SoCs making use of Qcom PCIe controller IP v2.1.0 do not support hotplug
functionality. But the hotplug capability bit is set by default in the
hardware. This causes the kernel PCI core to register hotplug service for
the controller and send hotplug commands to it. But those commands will
timeout generating messages as below during boot and suspend/resume.
[ 5.782159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2020 msec ago)
[ 5.810161] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2048 msec ago)
[ 7.838162] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2020 msec ago)
[ 7.870159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2052 msec ago)
This not only spams the console output but also induces a delay of a
couple of seconds. To fix this issue, let's clear the HPC bit in
PCI_EXP_SLTCAP register as a part of the post init sequence to not
advertise the hotplug capability for the controller.
Link: https://lore.kernel.org/r/20230619150408.8468-10-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
SoCs making use of Qcom PCIe controller IP v1.0.0 do not support hotplug
functionality. But the hotplug capability bit is set by default in the
hardware. This causes the kernel PCI core to register hotplug service for
the controller and send hotplug commands to it. But those commands will
timeout generating messages as below during boot and suspend/resume.
[ 5.782159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2020 msec ago)
[ 5.810161] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2048 msec ago)
[ 7.838162] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2020 msec ago)
[ 7.870159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2052 msec ago)
This not only spams the console output but also induces a delay of a
couple of seconds. To fix this issue, let's clear the HPC bit in
PCI_EXP_SLTCAP register as a part of the post init sequence to not
advertise the hotplug capability for the controller.
Link: https://lore.kernel.org/r/20230619150408.8468-9-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
SoCs making use of Qcom PCIe controller IP v2.3.2 do not support hotplug
functionality. But the hotplug capability bit is set by default in the
hardware. This causes the kernel PCI core to register hotplug service for
the controller and send hotplug commands to it. But those commands will
timeout generating messages as below during boot and suspend/resume.
[ 5.782159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2020 msec ago)
[ 5.810161] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2048 msec ago)
[ 7.838162] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2020 msec ago)
[ 7.870159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2052 msec ago)
This not only spams the console output but also induces a delay of a
couple of seconds. To fix this issue, let's clear the HPC bit in
PCI_EXP_SLTCAP register as a part of the post init sequence to not
advertise the hotplug capability for the controller.
Link: https://lore.kernel.org/r/20230619150408.8468-7-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
SoCs making use of Qcom PCIe controller IPs v2.3.3 and v2.9.0 do not
support hotplug functionality. But the hotplug capability bit is set by
default in the hardware. This causes the kernel PCI core to register
hotplug service for the controller and send hotplug commands to it. But
those commands will timeout generating messages as below during boot
and suspend/resume.
[ 5.782159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2020 msec ago)
[ 5.810161] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2048 msec ago)
[ 7.838162] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2020 msec ago)
[ 7.870159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2052 msec ago)
This not only spams the console output but also induces a delay of a
couple of seconds. To fix this issue, let's not set the HPC bit in
PCI_EXP_SLTCAP register as a part of the post init sequence to not
advertise the hotplug capability for the controller.
Link: https://lore.kernel.org/r/20230619150408.8468-6-manivannan.sadhasivam@linaro.org
Tested-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
SoCs making use of Qcom PCIe controller IPs v2.7.0 and v1.9.0 do not
support hotplug functionality. But the hotplug capability bit is set by
default in the hardware. This causes the kernel PCI core to register
hotplug service for the controller and send hotplug commands to it. But
those commands will timeout generating messages as below during boot and
suspend/resume.
[ 5.782159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2020 msec ago)
[ 5.810161] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2048 msec ago)
[ 7.838162] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2020 msec ago)
[ 7.870159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2052 msec ago)
This not only spams the console output but also induces a delay of a
couple of seconds. To fix this issue, let's clear the HPC bit in
PCI_EXP_SLTCAP register as a part of the post init sequence to not
advertise the hotplug capability for the controller.
Link: https://lore.kernel.org/r/20230619150408.8468-5-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
SM8550 requires two additional clocks for proper working.
Add these two clocks as optional clocks (as only required by this
platform) and compatible for this platform.
While at it, let's also rename the reset variable to "rst" from
"pci_reset" to match the existing naming preference.
Link: https://lore.kernel.org/r/20230320144658.1794991-2-abel.vesa@linaro.org
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
[lpieralisi@kernel.org: commit log rewording]
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
During the system suspend, vote for minimal interconnect bandwidth (1KiB)
to keep the interconnect path active for config access and also turn OFF
the resources like clock and PHY if there are no active devices connected
to the controller. For the controllers with active devices, the resources
are kept ON as removing the resources will trigger access violation during
the late end of suspend cycle as kernel tries to access the config space of
PCIe devices to mask the MSIs.
Also, it is not desirable to put the link into L2/L3 state as that
implies VDD supply will be removed and the devices may go into powerdown
state. This will affect the lifetime of storage devices like NVMe.
And finally, during resume, turn ON the resources if the controller was
truly suspended (resources OFF) and update the interconnect bandwidth
based on PCIe Gen speed.
Suggested-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
Link: https://lore.kernel.org/r/20230403154922.20704-2-manivannan.sadhasivam@linaro.org
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Dhruva Gole <d-gole@ti.com>
Qualcomm PCIe controllers have debug registers in the MHI region that
count PCIe link transitions. Expose them over debugfs to userspace to
help debug the low power issues.
Note that even though the registers are prefixed as PARF_, they don't
live under the "parf" register region. The register naming is following
the Qualcomm's internal documentation as like other registers.
While at it, let's arrange the local variables in probe function to follow
reverse XMAS tree order.
Link: https://lore.kernel.org/r/20230316081117.14288-20-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
All the resets are asserted and deasserted at the same time. So the bulk
reset APIs can be used to handle them together. This simplifies the code
a lot.
It should be noted that there were delays in-between the reset asserts and
deasserts. But going by the config used by other revisions, those delays
are not really necessary. So a single delay after all asserts and one after
deasserts is used.
The total number of resets supported is 12 but only ipq4019 is using all of
them.
Link: https://lore.kernel.org/r/20230316081117.14288-13-manivannan.sadhasivam@linaro.org
Tested-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
The PCIE part is redundant and 20 doesn't represent anything across the
SoCs supported now. So let's get rid of the prefix.
This involves adding the IP version suffix to one definition of
PARF_SLV_ADDR_SPACE_SIZE that defines offset specific to that version.
The other definition is generic for the rest of the versions.
Also, the register PCIE20_LNK_CONTROL2_LINK_STATUS2 is not used anywhere,
hence removed.
Link: https://lore.kernel.org/r/20230316081117.14288-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Qcom PCIe IP version v2.7.0 and its derivatives don't contain the
PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT register. Instead, they have the new
PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2 register. So fix the incorrect
register usage which is modifying a different register.
Also in this IP version, this register change doesn't depend on MSI
being enabled. So remove that check also.
Link: https://lore.kernel.org/r/20230316081117.14288-2-manivannan.sadhasivam@linaro.org
Fixes: ed8cc3b1fc ("PCI: qcom: Add support for SDM845 PCIe controller")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Cc: <stable@vger.kernel.org> # 5.6+
Pull phy updates from Vinod Koul:
"This tme we have again a big pile of qcom-qmp-* changes, one new
driver and bunch of new hardware support.
New hardware support:
- Allwinner H616 USB PHY and A100 DPHY support
- TI J721s2, J784s4 and J721e support
- Freescale i.MX8MP PCIe PHY support
- New driver for Renesas Ethernet SERDES supporting R-Car S4-8
- Qualcomm SM8450 PCIe1 PHY support in EP mode
- Qualcomm SC8280XP PCIe PHY support (including x4 mode)
- Fixed Qualcomm SC8280XP USB4-USB3-DP PHY DT bindings
Updates:
- A big pile of updates on qcom-qmp-* drivers following the driver
split and reorganization merged earlier
- Phy order of API calls documentation update"
* tag 'phy-for-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (174 commits)
phy: ti: phy-j721e-wiz: add j721s2-wiz-10g module support
dt-bindings: phy-j721e-wiz: add j721s2 compatible string
phy: use devm_platform_get_and_ioremap_resource()
phy: allwinner: phy-sun6i-mipi-dphy: Add the A100 DPHY variant
phy: allwinner: phy-sun6i-mipi-dphy: Add a variant power-on hook
phy: allwinner: phy-sun6i-mipi-dphy: Set the enable bit last
phy: allwinner: phy-sun6i-mipi-dphy: Make RX support optional
dt-bindings: sun6i-a31-mipi-dphy: Add the A100 DPHY variant
dt-bindings: sun6i-a31-mipi-dphy: Add the interrupts property
phy: qcom-qmp-pcie: drop redundant clock allocation
phy: qcom-qmp-usb: drop redundant clock allocation
phy: qcom-qmp: drop unused type header
phy: qcom-qmp-usb: drop sc8280xp reference-clock source
dt-bindings: phy: qcom,sc8280xp-qmp-usb3-uni: drop reference-clock source
phy: qcom-qmp-combo: add support for updated sc8280xp binding
phy: qcom-qmp-combo: rename DP_PHY register pointer
phy: qcom-qmp-combo: rename common-register pointers
phy: qcom-qmp-combo: clean up DP clock callbacks
phy: qcom-qmp-combo: separate clock and provider registration
phy: qcom-qmp-combo: add clock registration helper
...
On Qualcomm platforms like SC8280XP and SA8540P, interconnect bandwidth
must be requested before enabling interconnect clocks.
Add basic support for managing an optional "pcie-mem" interconnect path
by setting a low constraint before enabling clocks and updating it after
the link is up.
Note that it is not possible for a controller driver to set anything but
a maximum peak bandwidth as expected average bandwidth will vary with
use case and actual use (and power policy?). This very much remains an
unresolved problem with the interconnect framework.
Also note that no constraint is set for the SC8280XP/SA8540P "cpu-pcie"
path for now as it is not clear what an appropriate constraint would be
(and the system does not crash when left unspecified).
Link: https://lore.kernel.org/r/20221102090705.23634-3-johan+linaro@kernel.org
Fixes: 70574511f3 ("PCI: qcom: Add support for SC8280XP")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Brian Masney <bmasney@redhat.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
The various IP versions have different configurations that are encoded
in separate sets of operation callbacks. Currently, there is no need for
also maintaining corresponding sets of data parameters, but it is
conceivable that these may again be found useful (e.g. to implement
minor variations of the operation callbacks).
Rename the default configuration structures after the IP version they
apply to so that they can more easily be reused by different SoCs.
Note that SoC specific configurations can be added later if need arises
(e.g. cfg_sc8280xp).
Link: https://lore.kernel.org/r/20220714071348.6792-8-johan+linaro@kernel.org
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Brian Masney <bmasney@redhat.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
The kernel is not a devicetree validator and does not need to re-encode
information which is already available in the devicetree.
This is specifically true for the optional PCIe clocks, some of which
are really interconnect clocks.
Treat also the 2.7.0 optional clocks as truly optional instead of
maintaining a list of clocks per compatible (including two compatible
strings for the two identical controllers on sm8450) just to validate
the devicetree.
Link: https://lore.kernel.org/r/20220714071348.6792-7-johan+linaro@kernel.org
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Brian Masney <bmasney@redhat.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
The SC8280XP platform has seven PCIe controllers: two used with USB4,
two 4-lane, two 2-lane and one 1-lane.
Add a new "qcom,pcie-sc8280xp" compatible string and reuse the 1.9.0
ops.
Note that the SC8280XP controllers need two or three interconnect
clocks to be enabled. Model these as optional clocks to avoid encoding
devicetree data in the PCIe driver.
Note that the same could be done for the SM8450 interconnect clocks and
possibly also for the TBU clocks.
Link: https://lore.kernel.org/r/20220714071348.6792-5-johan+linaro@kernel.org
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
- Add PHY clock source implementation (Dmitry Baryshkov)
- Use new clk_regmap_phy_mux_ops for gcc-sm8450 and gcc-sc7280 PCIe pipe
clocks (Dmitry Baryshkov)
- Set up rev 2.1.0 PARF_PHY before enabling clocks (Christian Marangi)
- Power on PHY before accessing IPQ8074 DBI registers to avoid boot hangs
(Robert Marko)
- Power on PHY before accessing DBI registers on all variants for
consistency (Robert Marko)
- Remove unnecessary pipe_clk handling since this is done in PHY drivers
(Dmitry Baryshkov)
- Drop manual pipe_clk_src handling (Dmitry Baryshkov)
- Move GEN3_RELATED DBI definitions to common dwc header (Baruch Siach)
- Define slot capabilities using generic PCI_EXP_SLTCAP_* macros (Baruch
Siach)
- Add IPQ60xx support (Selvam Sathappan Periakaruppan)
- Fix DT description typo (Baruch Siach)
- Fix DT "compatibles" typo (Johan Hovold)
- Allow ASPM L1 and substates for 2.7.0 (Krishna chaitanya chundru)
* pci/ctrl/qcom:
PCI: qcom: Allow ASPM L1 and substates for 2.7.0
dt-bindings: PCI: qcom: Fix reset conditional
dt-bindings: PCI: qcom: Fix description typo
PCI: qcom: Add IPQ60xx support
PCI: qcom: Define slot capabilities using PCI_EXP_SLTCAP_*
PCI: dwc: Move GEN3_RELATED DBI definitions to common header
PCI: qcom: Drop manual pipe_clk_src handling
PCI: qcom: Remove unnecessary pipe_clk handling
PCI: qcom: Power on PHY before DBI register accesses
PCI: qcom: Power on PHY before IPQ8074 DBI register accesses
PCI: qcom: Set up rev 2.1.0 PARF_PHY before enabling clocks
clk: qcom: gcc-sc7280: use new clk_regmap_phy_mux_ops for PCIe pipe clocks
clk: qcom: gcc-sm8450: use new clk_regmap_phy_mux_ops for PCIe pipe clocks
clk: qcom: regmap: add PHY clock source implementation
IPQ8074 requires the PHY to be powered on before accessing DBI registers.
It's not clear whether other variants have the same dependency, but there
seems to be no reason for them to be different, so move all the DBI
accesses from .init() to .post_init() so they are all after phy_power_on().
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20220623155004.688090-2-robimarko@gmail.com
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
