Must be called in a non-atomic context, after the endpoint
has been registered with the hardware via xhci_add_endpoint
and before the first URB is submitted for the endpoint.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
xHCI caches device and endpoint data after the interface is configured,
so an explicit command needs to be issued for any device driver wanting
to alter the polling interval of an endpoint.
Add usb_fixup_endpoint() to allow drivers to do this. The fixup must be
called after calculating endpoint bandwidth requirements but before any
URBs are submitted.
If polling intervals are shortened, any bandwidth reservations are no
longer valid but in practice polling intervals are only ever relaxed.
Limit the scope to interrupt transfers for now.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
This falls under the same "we can reprogram glitch-free as long as we
pause generation" rule as updating the div/frac fields. This can be
used for runtime reclocking of V3D to manage power leakage.
Signed-off-by: Eric Anholt <eric@anholt.net>
Without the actual power management part any more, there's a lot less
to set up for V3D. We just need to clear the RSTN field for the power
domain, and expose the reset controller for toggling it again.
This is definitely incomplete -- the old ISP and H264 is in the old
bridge, but since we have no consumers of it I've just done the
minimum to get V3D working.
Signed-off-by: Eric Anholt <eric@anholt.net>
There are several warts surrounding bcmgenet_mii_probe() as this
function is called from ndo_open, but it's calling registration-type
functions. The probe should be called at probe time and refactored
such that the PHY device data can be extracted to limit the scope
of this flag to Broadcom PHYs.
For now, pass this flag in as it puts our attached PHY into a low-power
state when disconnected.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Set defaults for TX and RX packet coalescing to be equivalent to:
# ethtool -C eth0 tx-frames 10
# ethtool -C eth0 rx-usecs 50
This may be something we want to set via DT parameters in the
future.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The HWRNG on the BCM2838 is compatible to iproc-rng200, so add the
support to this driver instead of bcm2835-rng.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
hwrng: iproc-rng200: Correct SoC name
The Pi 4 SoC is called BCM2711, not BCM2838.
Fixes: "hwrng: iproc-rng200: Add BCM2838 support"
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The legacy peripherals can only address the first gigabyte of RAM, so
ensure that DMA allocations are restricted to that region.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The ioremapping creates mappings within the vmalloc area. The
equivalent early function, create_mapping, now checks that the
requested explicit virtual address is between VMALLOC_START and
VMALLOC_END. As there is no reason to have any correlation between
the physical and virtual addresses, put the required mappings at
VMALLOC_START and above.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
On error, vchiq_mmal_component_init could leave the
event context allocated for ports.
Clean them up in the error path.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
vchiq_mmal_component_init calls init_event_context for the
control port, but vchiq_mmal_component_finalise didn't free
it, causing a memory leak..
Add the free call.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
mmal_parameters.h hasn't been updated to reflect additions made
over the last few years. Update it to reflect the currently
supported parameters.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
The list of formats was copied before Bayer support was added.
The ISP supports Bayer and is being supported by the bcm2835_codec
driver, so add in the encodings for them.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
The debug text for how many clocks have been registered
uses "%d" with a size_t. Correct it to "%zd".
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
The MMAL client_component field is used with the event
mechanism to allow the client to identify the component for
which the event is generated.
The field is only 32bits in size, therefore we can't use a
pointer to the component in a 64 bit kernel.
Component handles are already held in an array per VCHI
instance, so use the array index as the client_component handle
to avoid having to create a new IDR for this purpose.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
videobuf2 only allowed exporting a dmabuf as a file descriptor,
but there are instances where having the struct dma_buf is
useful within the kernel.
Split the current implementation into two, one step which
exports a struct dma_buf, and the second which converts that
into an fd.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Add the ability to send data to ports. This only supports
zero copy mode as the required bulk transfer setup calls
are not done.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
(Preparation for the codec driver).
The codec uses the event mechanism to report things such as
resolution changes. It is signalled by the cmd field of the buffer
being non-zero.
Add support for passing this information out to the client.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Fixes up a checkpatch error "Avoid using bool structure members
because of possible alignment issues".
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
When calling tc358743_set_fmt, the code was calling tc358743_get_fmt
to choose a valid format. However that sets the colorspace
based on what was read back from the chip. When you set the format,
then the driver would choose and program the colorspace based
on the format code.
The result was that if you called try or set format for UYVY
when the current format was RGB3 then you would get told sRGB,
and try RGB3 when current was UYVY and you would get told
SMPTE170M.
The value programmed into the chip is determined by this driver,
therefore there is no need to read back the value. Return the
colorspace based on the format set/tried instead.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Document the DT bindings for the CSI2/CCP2 receiver peripheral
(known as Unicam) on BCM283x SoCs.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Acked-by: Rob Herring <robh@kernel.org>
New helper defines that allow printing of a FOURCC using
printf(V4L2_FOURCC_CONV, V4L2_FOURCC_CONV_ARGS(fourcc));
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
The ADV7282M can support YPbPr on AIN1-3, but this was
not selectable from the driver. Add it to the list of
supported input modes.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
The hardware default is differential CVBS on AIN1 & 2, which
isn't very useful.
Select the first input that is defined as valid for the
chip variant (typically CVBS_AIN1).
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
The probe for the TC358743 reads the CHIPID register from
the device and compares it to the expected value of 0.
If the I2C request fails then that also returns 0, so
the driver loads thinking that the device is there.
Generally I2C communications are reliable so there is
limited need to check the return value on every transfer,
therefore only amend the one read during probe to check
for I2C errors.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Adds register setups for running the CSI lanes at 972Mbit/s,
which allows 1080P50 UYVY down 2 lanes.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
g_mbus_config was supposed to indicate all supported lane numbers, not
only the number of those currently in active use. Since the TC358743
can dynamically reduce the number of active lanes if the required
bandwidth allows for it, report all lane numbers up to the connected
number of lanes as supported in pdata mode.
In device tree mode, do not report lane count and clock mode at all, as
the receiver driver can determine these from the device tree.
To allow communicating the number of currently active lanes, add a new
bitfield to the v4l2_mbus_config flags. This is a temporary fix, to be
used only until a better solution is found.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The existing fixed value of 16 worked for UYVY 720P60 over
2 lanes at 594MHz, or UYVY 1080P60 over 4 lanes. (RGB888
1080P60 needs 6 lanes at 594MHz).
It doesn't allow for lower resolutions to work as the FIFO
underflows.
374 is required for 1080P24-30 UYVY over 2 lanes @ 972Mbit/s, but
>374 means that the FIFO underflows on 1080P50 UYVY over 2 lanes
@ 972Mbit/s.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
The lan78xx uses a 12-byte hardware rx header, so there is no need
to allocate SKBs with NET_IP_ALIGN set. Removes alignment faults
in both dwc_otg and in ipv6 processing.
Add the ability to interpret the high bits of the dreq specifier as
flags to be included in the DMA_CS register. The motivation for this
change is the ability to set the DISDEBUG flag for SD card transfers
to avoid corruption when using the VPU debugger.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The bInterval is set to 4 (i.e. 8 microframes => 1ms) and the only bit
that the driver pays attention to is "link was reset". If there's a
flapping status bit in that endpoint data, (such as if PHY negotiation
needs a few tries to get a stable link) then polling at a slower rate
would act as a de-bounce.
See: https://github.com/raspberrypi/linux/issues/2447
The driver already reported the firmware build date during probe.
The mailbox calls have been extended to also report the variant
1 = standard start.elf
2 = start_x.elf (includes camera stack)
3 = start_db.elf (includes assert logging)
4 = start_cd.elf (cutdown version for smallest memory footprint).
Log the variant during probe.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
firmware: raspberrypi: Report the fw git hash during probe
The firmware can now report the git hash from which it was built
via the mailbox, so report it during probe.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Ethernet cables with faulty or missing pairs (specifically pairs C and
D) allow auto-negotiation to 1000Mbs, but do not support the successful
establishment of a link. Add a DT property, "microchip,downshift-after",
to configure the number of auto-negotiation failures after which it
falls back to 100Mbs. Valid values are 2, 3, 4, 5 and 0, where 0 means
never downshift.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Step wise governor increases the mitigation level when the temperature
goes above a threshold and will decrease the mitigation when the
temperature falls below the threshold. If it were a case, where the
temperature hovers around a threshold, the mitigation will be applied
and removed at every iteration. This reaction to the temperature is
inefficient for performance.
The use of hysteresis temperature could avoid this ping-pong of
mitigation by relaxing the mitigation to happen only when the
temperature goes below this lower hysteresis value.
Signed-off-by: Ram Chandrasekar <rkumbako@codeaurora.org>
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Avoid a hard userspace ABI change by adding a compatible get_throttled
sysfs entry. Its value is now feed by the GET_THROTTLED requests of the
new hwmon driver. The first access to get_throttled will generate
a warning.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
