[ Upstream commit 4ed2f3545c ]
The error handling code of fsl_ifc_ctrl_probe is problematic. When
fsl_ifc_ctrl_init fails or request_irq of fsl_ifc_ctrl_dev->irq fails,
it forgets to free the irq and nand_irq. Meanwhile, if request_irq of
fsl_ifc_ctrl_dev->nand_irq fails, it will still free nand_irq even if
the request_irq is not successful.
Fix this by refactoring the error handling code.
Fixes: d2ae2e20fb ("driver/memory:Move Freescale IFC driver to a common driver")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Link: https://lore.kernel.org/r/20210925151434.8170-1-mudongliangabcd@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit fff53a551d upstream.
This patch fixes 2 problems:
[1] The output warning logs and data loss when performing
mount/umount then remount the device with jffs2 format.
[2] The access width of SMWDR[0:1]/SMRDR[0:1] register is wrong.
This is the sample warning logs when performing mount/umount then
remount the device with jffs2 format:
jffs2: jffs2_scan_inode_node(): CRC failed on node at 0x031c51d4:
Read 0x00034e00, calculated 0xadb272a7
The reason for issue [1] is that the writing data seems to
get messed up.
Data is only completed when the number of bytes is divisible by 4.
If you only have 3 bytes of data left to write, 1 garbage byte
is inserted after the end of the write stream.
If you only have 2 bytes of data left to write, 2 bytes of '00'
are added into the write stream.
If you only have 1 byte of data left to write, 2 bytes of '00'
are added into the write stream. 1 garbage byte is inserted after
the end of the write stream.
To solve problem [1], data must be written continuously in serial
and the write stream ends when data is out.
Following HW manual 62.2.15, access to SMWDR0 register should be
in the same size as the transfer size specified in the SPIDE[3:0]
bits in the manual mode enable setting register (SMENR).
Be sure to access from address 0.
So, in 16-bit transfer (SPIDE[3:0]=b'1100), SMWDR0 should be
accessed by 16-bit width.
Similar to SMWDR1, SMDDR0/1 registers.
In current code, SMWDR0 register is accessed by regmap_write()
that only set up to do 32-bit width.
To solve problem [2], data must be written 16-bit or 8-bit when
transferring 1-byte or 2-byte.
Fixes: ca7d8b980b ("memory: add Renesas RPC-IF driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Duc Nguyen <duc.nguyen.ub@renesas.com>
[wsa: refactored to use regmap only via reg_read/reg_write]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210922091007.5516-1-wsa+renesas@sang-engineering.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tegra186_mc_client_sid_override() is only called from
an #ifdef block:
drivers/memory/tegra/tegra186.c:74:13: error: 'tegra186_mc_client_sid_override' defined but not used [-Werror=unused-function]
74 | static void tegra186_mc_client_sid_override(struct tegra_mc *mc,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Add another #ifdef around the called function.
Fixes: 393d66fd2c ("memory: tegra: Implement SID override programming")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20210722090748.1157470-1-arnd@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Memory controller drivers for v5.14 - Tegra SoC, part two
Second set of changes for Tegra SoC memory controller drivers,
containing patchset from Thierry Reding:
"The goal here is to avoid early identity mappings altogether and instead
postpone the need for the identity mappings to when devices are attached
to the SMMU. This works by making the SMMU driver coordinate with the
memory controller driver on when to start enforcing SMMU translations.
This makes Tegra behave in a more standard way and pushes the code to
deal with the Tegra-specific programming into the NVIDIA SMMU
implementation."
This pulls a dependency from Will Deacon (ARM SMMU driver) and contains
further ARM SMMU driver patches to resolve complex dependencies between
different patchsets. The pull from Will contains only one patch
("Implement ->probe_finalize()"). Further work in Will's tree might
depend on this patch, therefore patch was applied there.
On the other hand, this ("Implement ->probe_finalize()") patch is also a
dependency for ARM SMMU driver changes for Tegra. These changes,
bringing seamless transition from the firmware framebuffer to the OS
framebuffer, depend on earlier Tegra memory controller driver patches.
* tag 'memory-controller-drv-tegra-5.14-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl: (37 commits)
iommu/arm-smmu: Use Tegra implementation on Tegra186
iommu/arm-smmu: tegra: Implement SID override programming
iommu/arm-smmu: tegra: Detect number of instances at runtime
dt-bindings: arm-smmu: Add Tegra186 compatible string
memory: tegra: Delete dead debugfs checking code
iommu/arm-smmu: Implement ->probe_finalize()
memory: tegra: Implement SID override programming
memory: tegra: Split Tegra194 data into separate file
memory: tegra: Add memory client IDs to tables
memory: tegra: Unify drivers
memory: tegra: Only initialize reset controller if available
memory: tegra: Make IRQ support opitonal
memory: tegra: Parameterize interrupt handler
memory: tegra: Extract setup code into callback
memory: tegra: Make per-SoC setup more generic
memory: tegra: Push suspend/resume into SoC drivers
memory: tegra: Introduce struct tegra_mc_ops
memory: tegra: Unify struct tegra_mc across SoC generations
memory: tegra: Consolidate register fields
memory: tegra30-emc: Use devm_tegra_core_dev_init_opp_table()
...
Link: https://lore.kernel.org/r/20210614195200.21657-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Memory controller drivers for v5.14 - PL353
Bigger work around ARM Primecell PL35x SMC memory controller driver by
Miquel Raynal built on previous series from Naga Sureshkumar Relli.
This includes bindings cleanup and correction, converting these to
dtschema and several cleanyps in pl353-smc driver.
* tag 'memory-controller-drv-pl353-5.14' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl:
dt-binding: memory: pl353-smc: Convert to yaml
MAINTAINERS: Add PL353 SMC entry
memory: pl353-smc: Declare variables following a reverse christmas tree order
memory: pl353-smc: Avoid useless acronyms in descriptions
memory: pl353-smc: Let lower level controller drivers handle inits
memory: pl353-smc: Rename goto labels
memory: pl353-smc: Fix style
dt-binding: memory: pl353-smc: Fix the NAND controller node in the example
dt-binding: memory: pl353-smc: Drop unsupported nodes from the example
dt-binding: memory: pl353-smc: Fix the example syntax and style
dt-binding: memory: pl353-smc: Describe the child reg property
dt-binding: memory: pl353-smc: Drop the partitioning section
dt-binding: memory: pl353-smc: Document the range property
dt-binding: memory: pl353-smc: Rephrase the binding
Link: https://lore.kernel.org/r/20210611140659.61980-2-krzysztof.kozlowski@canonical.com
Signed-off-by: Olof Johansson <olof@lixom.net>
There is no point in having all these definitions at the SMC bus level,
these are extremely tight to the NAND controller driver implementation,
are not particularly generic, imply more boilerplate than needed, do
not really follow the device model by receiving no argument and some of
them are actually buggy.
Let's get rid of these right now as there is no current user and keep
this driver at a simple level: only the SMC bare initializations.
The NAND controller driver which I am going to introduce will take care
of redefining properly all these helpers and using them directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210610082040.2075611-13-miquel.raynal@bootlin.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
The driver defined several functions related to handling of frequency
and voltage changes:
- freq_post_notify_handling
- freq_pre_notify_handling
- volt_notify_handling
All these are static, not used inside or outside of driver, and marked
as unused with comment: "TODO: voltage notify handling should be hooked
up to regulator framework as soon as the necessary support is available
in mainline kernel. This function is un-used right now.".
These have been added with commit a93de288aa ("memory: emif: handle
frequency and voltage change events") in 2012 and are unused since then.
Additionally mentioned regulator and clock hooking did not happen since
then. If it did not happen for nine years, let's assume it will not
happen suddenly now.
Remove all unused functions which also allows removal of "t_ck" static
variable "t_ck" and "addressing" member of private structure.
No functionality is lost.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210527154101.80556-1-krzysztof.kozlowski@canonical.com
The debugfs_create_dir() function does not return NULL, it returns error
pointers. But in normal situations like this where the caller is not
dereferencing "emc->debugfs.root" then we are not supposed to check the
return. So instead of fixing these checks, we should delete them.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YMCQDTSyG8UuQoh0@mwanda
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Instead of programming all SID overrides during early boot, perform the
operation on-demand after the SMMU translations have been set up for a
device. This reuses data from device tree to match memory clients for a
device and programs the SID specified in device tree, which corresponds
to the SID used for the SMMU context banks for the device.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210603164632.1000458-2-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
The Tegra210 (and earlier) driver now supports all the functionality
that the Tegra186 (and later) driver does, so they can be unified.
Note that previously the Tegra186 (and later) driver could be unloaded,
even if that was perhaps not very useful. Older chips don't support that
yet, but once they do this code can be reenabled.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-11-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
The current per-SoC setup code runs at a fairly arbitrary point during
probe, thereby making it less flexible for other SoC generations. Move
the call around slightly (after only the very basic, common setup that
applies to all SoC generations has been performed), which will allow
it to be used for other implementations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-6-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
As another step towards unifying both the Tegra210 (and earlier) and
Tegra186 (and later) memory controller drivers, unify the structures
that are used to represent them.
Note that this comes at a slight space penalty since some fields are
not used on all generations, but the benefits of unifying the driver
outweigh the downsides.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-3-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Fix compilation warning on 64bit platforms caused by implicit promotion
of 32bit signed integer to a 64bit unsigned value which happens after
enabling compile-testing of the EMC drivers.
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Early exits from for_each_available_child_of_node() should decrement the
node reference counter. Reported by Coccinelle:
drivers/memory/atmel-ebi.c:593:1-33: WARNING:
Function "for_each_available_child_of_node" should have of_node_put() before return around line 604.
Fixes: 6a4ec4cd08 ("memory: add Atmel EBI (External Bus Interface) driver")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210423101815.119341-2-krzysztof.kozlowski@canonical.com
Pull power management updates from Rafael Wysocki:
"These add some new hardware support (for example, IceLake-D idle
states in intel_idle), fix some issues (for example, the handling of
negative "sleep length" values in cpuidle governors), add new
functionality to the existing drivers (for example, scale-invariance
support in the ACPI CPPC cpufreq driver) and clean up code all over.
Specifics:
- Add idle states table for IceLake-D to the intel_idle driver and
update IceLake-X C6 data in it (Artem Bityutskiy).
- Fix the C7 idle state on Tegra114 in the tegra cpuidle driver and
drop the unused do_idle() firmware call from it (Dmitry Osipenko).
- Fix cpuidle-qcom-spm Kconfig entry (He Ying).
- Fix handling of possible negative tick_nohz_get_next_hrtimer()
return values of in cpuidle governors (Rafael Wysocki).
- Add support for frequency-invariance to the ACPI CPPC cpufreq
driver and update the frequency-invariance engine (FIE) to use it
as needed (Viresh Kumar).
- Simplify the default delay_us setting in the ACPI CPPC cpufreq
driver (Tom Saeger).
- Clean up frequency-related computations in the intel_pstate cpufreq
driver (Rafael Wysocki).
- Fix TBG parent setting for load levels in the armada-37xx cpufreq
driver and drop the CPU PM clock .set_parent method for armada-37xx
(Marek Behún).
- Fix multiple issues in the armada-37xx cpufreq driver (Pali Rohár).
- Fix handling of dev_pm_opp_of_cpumask_add_table() return values in
cpufreq-dt to take the -EPROBE_DEFER one into acconut as
appropriate (Quanyang Wang).
- Fix format string in ia64-acpi-cpufreq (Sergei Trofimovich).
- Drop the unused for_each_policy() macro from cpufreq (Shaokun
Zhang).
- Simplify computations in the schedutil cpufreq governor to avoid
unnecessary overhead (Yue Hu).
- Fix typos in the s5pv210 cpufreq driver (Bhaskar Chowdhury).
- Fix cpufreq documentation links in Kconfig (Alexander Monakov).
- Fix PCI device power state handling in pci_enable_device_flags() to
avoid issuse in some cases when the device depends on an ACPI power
resource (Rafael Wysocki).
- Add missing documentation of pm_runtime_resume_and_get() (Alan
Stern).
- Add missing static inline stub for pm_runtime_has_no_callbacks() to
pm_runtime.h and drop the unused try_to_freeze_nowarn() definition
(YueHaibing).
- Drop duplicate struct device declaration from pm.h and fix a
structure type declaration in intel_rapl.h (Wan Jiabing).
- Use dev_set_name() instead of an open-coded equivalent of it in the
wakeup sources code and drop a redundant local variable
initialization from it (Andy Shevchenko, Colin Ian King).
- Use crc32 instead of md5 for e820 memory map integrity check during
resume from hibernation on x86 (Chris von Recklinghausen).
- Fix typos in comments in the system-wide and hibernation support
code (Lu Jialin).
- Modify the generic power domains (genpd) code to avoid resuming
devices in the "prepare" phase of system-wide suspend and
hibernation (Ulf Hansson).
- Add Hygon Fam18h RAPL support to the intel_rapl power capping
driver (Pu Wen).
- Add MAINTAINERS entry for the dynamic thermal power management
(DTPM) code (Daniel Lezcano).
- Add devm variants of operating performance points (OPP) API
functions and switch over some users of the OPP framework to the
new resource-managed API (Yangtao Li and Dmitry Osipenko).
- Update devfreq core:
* Register devfreq devices as cooling devices on demand (Daniel
Lezcano).
* Add missing unlock opeation in devfreq_add_device() (Lukasz
Luba).
* Use the next frequency as resume_freq instead of the previous
frequency when using the opp-suspend property (Dong Aisheng).
* Check get_dev_status in devfreq_update_stats() (Dong Aisheng).
* Fix set_freq path for the userspace governor in Kconfig (Dong
Aisheng).
* Remove invalid description of get_target_freq() (Dong Aisheng).
- Update devfreq drivers:
* imx8m-ddrc: Remove imx8m_ddrc_get_dev_status() and unneeded
of_match_ptr() (Dong Aisheng, Fabio Estevam).
* rk3399_dmc: dt-bindings: Add rockchip,pmu phandle and drop
references to undefined symbols (Enric Balletbo i Serra, Gaël
PORTAY).
* rk3399_dmc: Use dev_err_probe() to simplify the code (Krzysztof
Kozlowski).
* imx-bus: Remove unneeded of_match_ptr() (Fabio Estevam).
- Fix kernel-doc warnings in three places (Pierre-Louis Bossart).
- Fix typo in the pm-graph utility code (Ricardo Ribalda)"
* tag 'pm-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (74 commits)
PM: wakeup: remove redundant assignment to variable retval
PM: hibernate: x86: Use crc32 instead of md5 for hibernation e820 integrity check
cpufreq: Kconfig: fix documentation links
PM: wakeup: use dev_set_name() directly
PM: runtime: Add documentation for pm_runtime_resume_and_get()
cpufreq: intel_pstate: Simplify intel_pstate_update_perf_limits()
cpufreq: armada-37xx: Fix module unloading
cpufreq: armada-37xx: Remove cur_frequency variable
cpufreq: armada-37xx: Fix determining base CPU frequency
cpufreq: armada-37xx: Fix driver cleanup when registration failed
clk: mvebu: armada-37xx-periph: Fix workaround for switching from L1 to L0
clk: mvebu: armada-37xx-periph: Fix switching CPU freq from 250 Mhz to 1 GHz
cpufreq: armada-37xx: Fix the AVS value for load L1
clk: mvebu: armada-37xx-periph: remove .set_parent method for CPU PM clock
cpufreq: armada-37xx: Fix setting TBG parent for load levels
cpuidle: Fix ARM_QCOM_SPM_CPUIDLE configuration
cpuidle: tegra: Remove do_idle firmware call
cpuidle: tegra: Fix C7 idling state on Tegra114
PM: sleep: fix typos in comments
cpufreq: Remove unused for_each_policy macro
...
Normally, If the smi-larb HW need work, we should enable the smi-common
HW power and clock firstly.
This patch adds device-link between the smi-larb dev and the smi-common
dev. then If pm_runtime_get_sync(smi-larb-dev), the pm_runtime_get_sync
(smi-common-dev) will be called automatically.
Also, Add DL_FLAG_STATELESS to avoid the smi-common clocks be gated when
probe.
CC: Matthias Brugger <matthias.bgg@gmail.com>
Suggested-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210410091128.31823-5-yong.wu@mediatek.com
Memory controller drivers for v5.13 - Tegra SoC
1. Few cleanups.
2. Add debug statistics to Tegra20 memory controller.
3. Update bindings and convert to dtschema. This update is not
backwards compatible (ABI break) however the broken part was added
recently (v5.11) and there are no users of it yet.
* tag 'memory-controller-drv-tegra-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl:
dt-bindings: memory: tegra20: mc: Convert to schema
dt-bindings: memory: tegra124: emc: Replace core regulator with power domain
dt-bindings: memory: tegra30: emc: Replace core regulator with power domain
dt-bindings: memory: tegra20: emc: Replace core regulator with power domain
memory: tegra: Print out info-level once per driver probe
memory: tegra20: Protect debug code with a lock
memory: tegra20: Correct comment to MC_STAT registers writes
memory: tegra20: Add debug statistics
memory: tegra: replace DEFINE_SIMPLE_ATTRIBUTE with DEFINE_DEBUGFS_ATTRIBUTE
Link: https://lore.kernel.org/r/20210407161333.73013-2-krzysztof.kozlowski@canonical.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
