ASoC: Add support for Rpi-DAC
ASoC: Add prompt for ICS43432 codec
Without a prompt string, a config setting can't be included in a
defconfig. Give CONFIG_SND_SOC_ICS43432 a prompt so that Pi soundcards
can use the driver.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Add IQaudIO Sound Card support for Raspberry Pi
Set a limit of 0dB on Digital Volume Control
The main volume control in the PCM512x DAC has a range up to
+24dB. This is dangerously loud and can potentially cause massive
clipping in the output stages. Therefore this sets a sensible
limit of 0dB for this control.
Allow up to 24dB digital gain to be applied when using IQAudIO DAC+
24db_digital_gain DT param can be used to specify that PCM512x
codec "Digital" volume control should not be limited to 0dB gain,
and if specified will allow the full 24dB gain.
Modify IQAudIO DAC+ ASoC driver to set card/dai config from dt
Add the ability to set the card name, dai name and dai stream name, from
dt config.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
IQaudIO: auto-mute for AMP+ and DigiAMP+
IQAudIO amplifier mute via GPIO22. Add dt params for "one-shot" unmute
and auto mute.
Revision 2, auto mute implementing HiassofT suggestion to mute/unmute
using set_bias_level, rather than startup/shutdown....
"By default DAPM waits 5 seconds (pmdown_time) before shutting down
playback streams so a close/stop immediately followed by open/start
doesn't trigger an amp mute+unmute."
Tested on both AMP+ (via DAC+) and DigiAMP+, with both options...
dtoverlay=iqaudio-dacplus,unmute_amp
"one-shot" unmute when kernel module loads.
dtoverlay=iqaudio-dacplus,auto_mute_amp
Unmute amp when ALSA device opened by a client. Mute, with 5 second delay
when ALSA device closed. (Re-opening the device within the 5 second close
window, will cancel mute.)
Revision 4, using gpiod.
Revision 5, clean-up formatting before adding mute code.
- Convert tab plus 4 space formatting to 2x tab
- Remove '// NOT USED' commented code
Revision 6, don't attempt to "one-shot" unmute amp, unless card is
successfully registered.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
ASoC: iqaudio-dac: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: iqaudio-dac: use modern dai_link style
Signed-off-by: Matthias Reichl <hias@horus.com>
Added support for HiFiBerry DAC+
The driver is based on the HiFiBerry DAC driver. However HiFiBerry DAC+ uses
a different codec chip (PCM5122), therefore a new driver is necessary.
Add support for the HiFiBerry DAC+ Pro.
The HiFiBerry DAC+ and DAC+ Pro products both use the existing bcm sound driver with the DAC+ Pro having a special clock device driver representing the two high precision oscillators.
An addition bug fix is included for the PCM512x codec where by the physical size of the sample frame is used in the calculation of the LRCK divisor as it was found to be wrong when using 24-bit depth sample contained in a little endian 4-byte sample frame.
Limit PCM512x "Digital" gain to 0dB by default with HiFiBerry DAC+
24db_digital_gain DT param can be used to specify that PCM512x
codec "Digital" volume control should not be limited to 0dB gain,
and if specified will allow the full 24dB gain.
Add dt param to force HiFiBerry DAC+ Pro into slave mode
"dtoverlay=hifiberry-dacplus,slave"
Add 'slave' param to use HiFiBerry DAC+ Pro in slave mode,
with Pi as master for bit and frame clock.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
Fixed a bug when using 352.8kHz sample rate
Signed-off-by: Daniel Matuschek <daniel@hifiberry.com>
ASoC: pcm512x: revert downstream changes
This partially reverts commit 185ea05465
which was added by https://github.com/raspberrypi/linux/pull/1152
The downstream pcm512x changes caused a regression, it broke normal
use of the 24bit format with the codec, eg when using simple-audio-card.
The actual bug with 24bit playback is the incorrect usage
of physical_width in various drivers in the downstream tree
which causes 24bit data to be transmitted with 32 clock
cycles. So it's not the pcm512x that needs fixing, it's the
soundcard drivers.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: hifiberry_dacplus: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: hifiberry_dacplus: transmit S24_LE with 64 BCLK cycles
Signed-off-by: Matthias Reichl <hias@horus.com>
hifiberry_dacplus: switch to snd_soc_dai_set_bclk_ratio
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: hifiberry_dacplus: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add driver for rpi-proto
Forward port of 3.10.x driver from https://github.com/koalo
We are using a custom board and would like to use rpi 3.18.x
kernel. Patch works fine for our embedded system.
URL to the audio chip:
http://www.mikroe.com/add-on-boards/audio-voice/audio-codec-proto/
Playback tested with devicetree enabled.
Signed-off-by: Waldemar Brodkorb <wbrodkorb@conet.de>
ASoC: rpi-proto: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add Support for JustBoom Audio boards
justboom-dac: Adjust for ALSA API change
As of 4.4, snd_soc_limit_volume now takes a struct snd_soc_card *
rather than a struct snd_soc_codec *.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
ASoC: justboom-dac: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Also remove hw_params as it's no longer needed.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: justboom-dac: use modern dai_link style
Signed-off-by: Matthias Reichl <hias@horus.com>
New AudioInjector.net Pi soundcard with low jitter audio in and out.
Contains the sound/soc/bcm ALSA machine driver and necessary alterations to the Kconfig and Makefile.
Adds the dts overlay and updates the Makefile and README.
Updates the relevant defconfig files to enable building for the Raspberry Pi.
Thanks to Phil Elwell (pelwell) for the review, simple-card concepts and discussion. Thanks to Clive Messer for overlay naming suggestions.
Added support for headphones, microphone and bclk_ratio settings.
This patch adds headphone and microphone capability to the Audio Injector sound card. The patch also sets the bit clock ratio for use in the bcm2835-i2s driver. The bcm2835-i2s can't handle an 8 kHz sample rate when the bit clock is at 12 MHz because its register is only 10 bits wide which can't represent the ch2 offset of 1508. For that reason, the rate constraint is added.
ASoC: audioinjector-pi-soundcard: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
New driver for RRA DigiDAC1 soundcard using WM8741 + WM8804
ASoC: digidac1-soundcard: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add support for Dion Audio LOCO DAC-AMP HAT
Using dedicated machine driver and pcm5102a codec driver.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
ASoC: dionaudio_loco: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Allo Piano DAC boards: Initial 2 channel (stereo) support (#1645)
Add initial 2 channel (stereo) support for Allo Piano DAC (2.0/2.1) boards,
using allo-piano-dac-pcm512x-audio overlay and allo-piano-dac ALSA ASoC
machine driver.
NB. The initial support is 2 channel (stereo) ONLY!
(The Piano DAC 2.1 will only support 2 channel (stereo) left/right output,
pending an update to the upstream pcm512x codec driver, which will have
to be submitted via upstream. With the initial downstream support,
provided by this patch, the Piano DAC 2.1 subwoofer outputs will
not function.)
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net>
Signed-off-by: Clive Messer <clive.messer@digitaldreamtime.co.uk>
Tested-by: Clive Messer <clive.messer@digitaldreamtime.co.uk>
ASoC: allo-piano-dac: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Also remove hw_params and ops as they are no longer needed.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: allo-piano-dac: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add support for Allo Piano DAC 2.1 plus add-on board for Raspberry Pi.
The Piano DAC 2.1 has support for 4 channels with subwoofer.
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net>
Reviewed-by: Vijay Kumar B. <vijaykumar@zilogic.com>
Reviewed-by: Raashid Muhammed <raashidmuhammed@zilogic.com>
Add clock changes and mute gpios (#1938)
Also improve code style and adhere to ALSA coding conventions.
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net>
Reviewed-by: Vijay Kumar B. <vijaykumar@zilogic.com>
Reviewed-by: Raashid Muhammed <raashidmuhammed@zilogic.com>
PianoPlus: Dual Mono & Dual Stereo features added (#2069)
allo-piano-dac-plus: Master volume added + fixes
Master volume added, which controls both DACs volumes.
See: https://github.com/raspberrypi/linux/pull/2149
Also fix initial max volume, default mode value, and unmute.
Signed-off-by: allocom <sparky-dev@allo.com>
ASoC: allo-piano-dac-plus: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Signed-off-by: Matthias Reichl <hias@horus.com>
sound: bcm: Fix memset dereference warning
This warning appears with GCC 6.4.0 from toolchains.bootlin.com:
../sound/soc/bcm/allo-piano-dac-plus.c: In function ‘snd_allo_piano_dac_init’:
../sound/soc/bcm/allo-piano-dac-plus.c:711:30: warning: argument to ‘sizeof’ in ‘memset’ call is the same expression as the destination; did you mean to dereference it? [-Wsizeof-pointer-memaccess]
memset(glb_ptr, 0x00, sizeof(glb_ptr));
^
Suggested-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
ASoC: allo-piano-dac-plus: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add support for Allo Boss DAC add-on board for Raspberry Pi. (#1924)
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net>
Reviewed-by: Deepak <deepak@zilogic.com>
Reviewed-by: BabuSubashChandar <babusubashchandar@zilogic.com>
Add support for new clock rate and mute gpios.
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net>
Reviewed-by: Deepak <deepak@zilogic.com>
Reviewed-by: BabuSubashChandar <babusubashchandar@zilogic.com>
ASoC: allo-boss-dac: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: allo-boss-dac: transmit S24_LE with 64 BCLK cycles
Signed-off-by: Matthias Reichl <hias@horus.com>
allo-boss-dac: switch to snd_soc_dai_set_bclk_ratio
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: allo-boss-dac: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Support for Blokas Labs pisound board
Pisound dynamic overlay (#1760)
Restructuring pisound-overlay.dts, so it can be loaded and unloaded dynamically using dtoverlay.
Print a logline when the kernel module is removed.
pisound improvements:
* Added a writable sysfs object to enable scripts / user space software
to blink MIDI activity LEDs for variable duration.
* Improved hw_param constraints setting.
* Added compatibility with S16_LE sample format.
* Exposed some simple placeholder volume controls, so the card appears
in volumealsa widget.
Add missing SND_PISOUND selects dependency to SND_RAWMIDI
Without it the Pisound module fails to compile.
See https://github.com/raspberrypi/linux/issues/2366
Updates for Pisound module code:
* Merged 'Fix a warning in DEBUG builds' (1c8b82b).
* Updating some strings and copyright information.
* Fix for handling high load of MIDI input and output.
* Use dual rate oversampling ratio for 96kHz instead of single
rate one.
Signed-off-by: Giedrius Trainavicius <giedrius@blokas.io>
Fixing memset call in pisound.c
Signed-off-by: Giedrius Trainavicius <giedrius@blokas.io>
Fix for Pisound's MIDI Input getting blocked for a while in rare cases.
There was a possible race condition which could lead to Input's FIFO queue
to be underflown, causing high amount of processing in the worker thread for
some period of time.
Signed-off-by: Giedrius Trainavicius <giedrius@blokas.io>
Fix for Pisound kernel module in Real Time kernel configuration.
When handler of data_available interrupt is fired, queue_work ends up
getting called and it can block on a spin lock which is not allowed in
interrupt context. The fix was to run the handler from a thread context
instead.
Pisound: Remove spinlock usage around spi_sync
ASoC: pisound: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
ASoC: pisound: fix the parameter for spi_device_match
Signed-off-by: Hui Wang <hui.wang@canonical.com>
ASoC: Add driver for Cirrus Logic Audio Card
Note: due to problems with deferred probing of regulators
the following softdep should be added to a modprobe.d file
softdep arizona-spi pre: arizona-ldo1
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: rpi-cirrus: use modern dai_link style
Signed-off-by: Matthias Reichl <hias@horus.com>
sound: Support for Dion Audio LOCO-V2 DAC-AMP HAT
Signed-off-by: Miquel Blauw <info@dionaudio.nl>
ASoC: dionaudio_loco-v2: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Also remove hw_params and ops as they are no longer needed.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: dionaudio_loco-v2: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add support for Fe-Pi audio sound card. (#1867)
Fe-Pi Audio Sound Card is based on NXP SGTL5000 codec.
Mechanical specification of the board is the same the Raspberry Pi Zero.
3.5mm jacks for Headphone/Mic, Line In, and Line Out.
Signed-off-by: Henry Kupis <fe-pi@cox.net>
ASoC: fe-pi-audio: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add support for the AudioInjector.net Octo sound card
AudioInjector Octo: sample rates, regulators, reset
This patch adds new sample rates to the Audioinjector Octo sound card. The
new supported rates are (in kHz) :
96, 48, 32, 24, 16, 8, 88.2, 44.1, 29.4, 22.05, 14.7
Reference the bcm270x DT regulators in the overlay.
This patch adds a reset GPIO for the AudioInjector.net octo sound card.
Audioinjector octo : Make the playback and capture symmetric
This patch ensures that the sample rate and channel count of the audioinjector
octo sound card are symmetric.
audioinjector-octo: Add continuous clock feature
By user request, add a switch to prevent the clocks being stopped when
the stream is paused, stopped or shutdown. Provide access to the switch
by adding a 'non-stop-clocks' parameter to the audioinjector-addons
overlay.
See: https://github.com/raspberrypi/linux/issues/2409
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
sound: Fixes for audioinjector-octo under 4.19
1. Move the DT alias declaration to the I2C shim in the cases
where the shim is enabled. This works around a problem caused by a
4.19 commit [1] that generates DT/OF uevents for I2C drivers.
2. Fix the diagnostics in an error path of the soundcard driver to
correctly identify the reason for the failure to load.
3. Move the declaration of the clock node in the overlay outside
the I2C node to avoid warnings.
4. Sort the overlay nodes so that dependencies are only to earlier
fragments, in an attempt to get runtime dtoverlay application to
work (it still doesn't...)
See: https://github.com/Audio-Injector/Octo/issues/14
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
[1] af503716ac ("i2c: core: report OF style module alias for devices registered via OF")
ASoC: audioinjector-octo-soundcard: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Driver support for Google voiceHAT soundcard.
ASoC: googlevoicehat-codec: Use correct device when grabbing GPIO
The fixup for the VoiceHAT in 4.18 incorrectly tried to find the
sdmode GPIO pin under the card device, not the codec device.
This failed, and therefore caused the device probe to fail.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
ASoC: googlevoicehat-codec: Reformat for kernel coding standards
Fix all whitespace, indentation, and bracing errors.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
ASoC: googlevoicehat-codec: Make driver function structure const
Make voicehat_component_driver a const structure.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
ASoC: googlevoicehat-codec: Only convert from ms to jiffies once
Minor optimisation and allows to become checkpatch clean.
A msec value is read out of DT or from a define, and convert once to
jiffies, rather than every time that it is used.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Driver and overlay for Allo Katana DAC
Allo Katana DAC: Updated default values
Signed-off-by: Jaikumar <jaikumar@cem-solutions.com>
Added mute stream func
Signed-off-by: Jaikumar <jaikumar@cem-solutions.net>
codecs: Correct Katana minimum volume
Update Katana minimum volume to get the exact 0.5 dB value in each step.
Signed-off-by: Sudeep Kumar <sudeepkumar@cem-solutions.net>
ASoC: Add generic RPI driver for simple soundcards.
The RPI simple sound card driver provides a generic ALSA SOC card driver
supporting a variety of Pi HAT soundcards. The intention is to avoid
the duplication of code for cards that can't be fully supported by
the soc simple/graph cards but are otherwise almost identical.
This initial commit adds support for the ADAU1977 ADC, Google VoiceHat,
HifiBerry AMP, HifiBerry DAC and RPI DAC.
Signed-off-by: Tim Gover <tim.gover@raspberrypi.org>
ASoC: Use correct card name in rpi-simple driver
Use the specific card name from drvdata instead of the snd_rpi_simple
rpi-simple-soundcard: Use nicer driver name "RPi-simple"
Rename the driver from "RPI simple soundcard" to "RPi-simple" so that
the driver name won't be mangled allowing to be used unaltered as the
card conf filename.
ASoC: rpi-simple-soundcard: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
ASoC: Add Kconfig and Makefile for sound/soc/bcm
Signed-off-by: popcornmix <popcornmix@gmail.com>
ASoC: Create a generic Pi Hat WM8804 driver
Reduce the amount of duplicated code by creating a generic driver for
Pi Hat digi cards using the WM8804 codec.
This replaces the
Allo DigiOne, Hifiberry Digi/Pro, JustBoom Digi and IQAudIO Digi
dedicate soundcard drivers with a generic driver.
There are no significant changes to the runtime behavior of the drivers
and end users should not have to change any configuration settings
after upgrading.
Minor changes
* Check the return value of snd_soc_component_update_bits
* Added some pr_debug tracing
* Various checkpatch tidyups
* Updated allodigi-one to use use 128FS at > 96 Khz. This appears to
be an omission in the original driver code so followed the Hifiberry
DAC driver approach.
ASoC: rpi-wm8804-soundcard: use modern dai_link style
Signed-off-by: Matthias Reichl <hias@horus.com>
rpi-wm8804-soundcard: drop PWRDN register writes
Since kernel 4.0 the PWRDN register bits are under DAPM
control from the wm8804 driver.
Drop code that modifies that register to avoid interfering
with DAPM.
Signed-off-by: Matthias Reichl <hias@horus.com>
rpi-wm8804-soundcard: configure wm8804 clocks only on rate change
This should avoid clicks when stopping and immediately afterwards
starting a stream with the same samplerate as before.
Signed-off-by: Matthias Reichl <hias@horus.com>
rpi-wm8804-soundcard: Fixed MCLKDIV for Allo Digione
The Allo Digione board wants a fixed MCLKDIV of 256.
See: https://github.com/raspberrypi/linux/issues/3296
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
ASoC: Add support for AudioSense-Pi add-on soundcard
AudioSense-Pi is a RPi HAT based on a TI's TLV320AIC32x4 stereo codec
This hardware provides multiple audio I/O capabilities to the RPi.
The codec connects to the RPi's SoC through the I2S Bus.
The following devices can be connected through a 3.5mm jack
1. Line-In: Plain old audio in from mobile phones, PCs, etc.,
2. Mic-In: Connect a microphone
3. Line-Out: Connect the output to a speaker
4. Headphones: Connect a Headphone w or w/o microphones
Multiple Inputs:
It supports the following combinations
1. Two stereo Line-Inputs and a microphone
2. One stereo Line-Input and two microphones
3. Two stereo Line-Inputs, a microphone and
one mono line-input (with h/w hack)
4. One stereo Line-Input, two microphones and
one mono line-input (with h/w hack)
Multiple Outputs:
Audio output can be routed to the headphones or
speakers (with additional hardware)
Signed-off-by: b-ak <anur.bhargav@gmail.com>
ASoC: audiosense-pi: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Added driver for the HiFiBerry DAC+ ADC (#2694)
Signed-off-by: Daniel Matuschek <daniel@hifiberry.com>
hifiberry_dacplusadc: switch to snd_soc_dai_set_bclk_ratio
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: hifiberry_dacplusadc: fix DAI link setup
The driver only defines a single DAI link and the code that tries
to setup the second (non-existent) DAI link looks wrong - using dmic
as a CPU/platform driver doesn't make any sense.
The DT overlay doesn't define a dmic property, so the code was never
executed (otherwise it would have resulted in a memory corruption).
So drop the offending code to prevent issues if a dmic property
should be added to the DT overlay.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: hifiberry_dacplusadc: use modern dai_link style
Signed-off-by: Matthias Reichl <hias@horus.com>
Audiophonics I-Sabre 9038Q2M DAC driver
Signed-off-by: Audiophonics <contact@audiophonics.fr>
ASoC: i-sabre-q2m: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Added IQaudIO Pi-Codec board support (#2969)
Add support for the IQaudIO Pi-Codec board.
Signed-off-by: Gordon <gordon@iqaudio.com>
Fixed 48k timing issue
ASoC: iqaudio-codec: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
adds the Hifiberry DAC+ADC PRO version
This adds the driver for the DAC+ADC PRO version of the Hifiberry soundcard with software controlled PCM1863 ADC
Signed-off-by: Joerg Schambacher joerg@i2audio.com
Add Hifiberry DAC+DSP soundcard driver (#3224)
Adds the driver for the Hifiberry DAC+DSP. It supports capture and
playback depending on the DSP firmware.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
Allow simultaneous use of JustBoom DAC and Digi
Signed-off-by: Johannes Krude <johannes@krude.de>
Pisound: MIDI communication fixes for scaled down CPU.
* Increased maximum SPI communication speed to avoid running too slow
when the CPU is scaled down and losing MIDI data.
* Keep track of buffer usage in millibytes for higher precision.
Signed-off-by: Giedrius Trainavičius <giedrius@blokas.io>
sound: Add the HiFiBerry DAC+HD version
This adds the driver for the DAC+HD version supporting HiFiBerry's
PCM179x based DACs. It also adds PLL control for clock generation.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
Fix master mode settings of HiFiBerry DAC+ADC PRO card (#3424)
This patch fixes the board DAI setting when in master-mode.
Wrong setting could have caused random pop noise.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
adds LED OFF feature to HiFiBerry DAC+ADC PRO sound card
This adds a DT overlay parameter 'leds_off' which allows
to switch off the onboard activity LEDs at all times
which has been requested by some users.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
adds LED OFF feature to HiFiBerry DAC+ADC sound card
This adds a DT overlay parameter 'leds_off' which allows
to switch off the onboard activity LEDs at all times
which has been requested by some users.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
adds LED OFF feature to HiFiBerry DAC+/DAC+PRO sound cards
This adds a DT overlay parameter 'leds_off' which allows
to switch off the onboard activity LEDs at all times
which has been requested by some users.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
pisound: Added reading Pisound board hardware revision and exposing it (#3425)
pisound: Added reading Pisound board hardware revision and exposing it in kernel log and sysfs file:
/sys/kernel/pisound/hw_version
Signed-off-by: Giedrius <giedrius@blokas.io>
Added driver for HiFiBerry Amp amplifier add-on board
The driver contains a low-level hardware driver for the TAS5713 and the
drivers for the Raspberry Pi I2S subsystem.
TAS5713: return error if initialisation fails
Existing TAS5713 driver logs errors during initialisation, but does not return
an error code. Therefore even if initialisation fails, the driver will still be
loaded, but won't work. This patch fixes this. I2C communication error will now
reported correctly by a non-zero return code.
HiFiBerry Amp: fix device-tree problems
Some code to load the driver based on device-tree-overlays was missing. This is added by this patch.
According to 5713 pdf doc CLOCK_CTRL is a readonly status register, and it behaves so. Remove useless setting
sound: pcm512x-codec: Adding 352.8kHz samplerate support
sound/soc: only first codec is master in multicodec setup
When using multiple codecs, at most one codec should generate the master
clock. All codecs except the first are therefore configured for slave
mode.
Signed-off-by: Johannes Krude <johannes@krude.de>
ASoC: Fix snd_soc_get_pcm_runtime usage
Commit [1] changed the snd_soc_get_pcm_runtime to take a dai_link
pointer instead of a string. Patch up the downstream drivers to use
the modified API.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
[1] 4468189ff3 ("ASoC: soc-core: find rtd via dai_link pointer at snd_soc_get_pcm_runtime()")
Add support for the AudioInjector.net Isolated sound card
This patch adds support for the Audio Injector Isolated sound card.
Signed-off-by: Matt Flax <flatmax@flatmax.org>
Add support for merus-amp soundcard and ma120x0p codec
Add 96KHz rate support to MA120X0P codec and make enable and mute gpio
pins optional.
Signed-off-by: AMuszkat <ariel.muszkat@gmail.com>
Fixes a problem with clock settings of HiFiBerry DAC+ADC PRO (#3545)
This patch fixes a problem of the re-calculation of
i2s-clock and -parameter settings when only the ADC is activated.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
configs: Enable the AD193x codecs
See: https://github.com/raspberrypi/linux/issues/2850
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Switch to snd_soc_dai_set_bclk_ratio
Replaces obsolete function snd_soc_dai_set_tdm_slot
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
Enhances the DAC+ driver to control the optional headphone amplifier
Probes on the I2C bus for TPA6130A2, if successful, it sets DT-parameter
'status' from 'disabled' to 'okay' using change_sets to enable
the headphone control.
Signed-off-by: Joerg Schambacher joerg@i2audio.com
Update Allo Piano Dac Driver
Add unique names to the individual dac coded drivers
Remove some of the codec controls that are not used.
Signed-off-by: Paul Hermann <paul@picoreplayer.org>
Fixes an onboard clock detection problem of the PRO versions
Increasing the sleep time after clock selection to 3-4ms
allows the correct detection of all combinations of DAC+ Pro
and DAC+ADC Pro sound cards and the various PI revisions.
Signed-off-by: Joerg Schambacher <joerg@hifiberry.com>
At present there is no mechanism to specify driver load order,
which can lead to deferrals and repeated retries until successful.
Since this situation is expected, reduce the dmesg level to
INFO and mention that the operation will be retried.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
'component' is allocated in snd_soc_register_component(), but component->list
is not initalized, this may cause snd_soc_del_component_unlocked() deref null
ptr in the error handing case.
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
RIP: 0010:__list_del_entry_valid+0x81/0xf0
Call Trace:
snd_soc_del_component_unlocked+0x69/0x1b0 [snd_soc_core]
snd_soc_add_component.cold+0x54/0x6c [snd_soc_core]
snd_soc_register_component+0x70/0x90 [snd_soc_core]
devm_snd_soc_register_component+0x5e/0xd0 [snd_soc_core]
tas2552_probe+0x265/0x320 [snd_soc_tas2552]
? tas2552_component_probe+0x1e0/0x1e0 [snd_soc_tas2552]
i2c_device_probe+0xa31/0xbe0
Fix by adding INIT_LIST_HEAD() to snd_soc_component_initialize().
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20211009065840.3196239-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC: Updates for v5.14
This release sees a nice new feature in the core from Morimoto-san,
support for automatic negotiation of DAI formats between the components
on the link. Otherwise the big highlight was the merging of the Tegra
machine drivers into a single driver avoiding a bunch of duplication.
- Support for automatic negotiation of DAI formats.
- Accessory detection support for several Qualcomm parts.
- Support for IEC958 control with hdmi-codec.
- Merging of Tegra machine drivers into a single driver.
- Support for AmLogic SM1 TOACODEC, Intel AlderLake-M, several NXP
i.MX8 variants, NXP TFA1 and TDF9897, Rockchip RK817, Qualcomm
Quinary MI2S, Texas Instruments TAS2505
ASoC: Fixes for v5.13
A final batch of fixes for v5.13, this is larger than I'd like due to
the fixes for a series of suspend issues that Intel turned up in their
testing this week.
snd_soc_of_parse_daifmt() parses daifmt, but bitclock/frame provider
parsing part is one of headacke, because we are assuming below both cases.
A) node {
bitclock-master;
frame-master;
...
};
B) link {
bitclock-master = <&xxx>;
frame-master = <&xxx>;
...
};
The original was style A), and style B) was added later
by commit b3ca11ff59 ("ASoC: simple-card: Move dai-link level
properties away from dai subnodes").
snd_soc_of_parse_daifmt() parses it as style A),
and user need to update it to style B) if needed.
To handle it more flexibile, this patch adds new functions
which separates snd_soc_of_parse_daifmt() helper function.
snd_soc_daifmt_parse_format() :for DAI format
snd_soc_daifmt_parse_clock_provider_as_flag() :for style A)
snd_soc_daifmt_parse_clock_provider_as_phandl() :for style B)
snd_soc_daifmt_parse_clock_provider_as_bitmap() :use with _from_bitmap
This means
snd_soc_of_parse_daifmt() ==
snd_soc_daifmt_parse_format() |
snd_soc_daifmt_parse_clock_provider_as_flag()
This patch also indicate relatesionship comment for
snd_soc_daifmt_clock_provider_from_bitmap().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/877dixw9ej.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC is using dai_link which specify DAI format (= dai_link->dai_fmt),
and it is selected by "Sound Card" driver in corrent implementation.
In other words, Sound Card *needs* to setup it.
But, it should be possible to automatically selected from CPU and
Codec driver settings.
This patch adds new .auto_selectable_formats support
at snd_soc_dai_ops.
By this patch, dai_fmt can be automatically selected from each
driver if both CPU / Codec driver had it.
Automatically selectable *field* is depends on each drivers.
For example, some driver want to select format "automatically",
but want to select other fields "manually", because of complex limitation.
Or other example, in case of both CPU and Codec are possible to be
clock provider, but the quality was different.
In these case, user need/want to *manually* select each fields
from Sound Card driver.
This .auto_selectable_formats can set priority.
For example, no limitaion format can be HI priority,
supported but has picky limitation format can be next priority, etc.
It uses Sound Card specified fields preferentially, and try to select
non-specific fields from CPU and Codec driver automatically
if all drivers have .auto_selectable_formats.
In other words, we can select all dai_fmt via Sound Card driver
same as before.
Link: https://lore.kernel.org/r/871rb3hypy.wl-kuninori.morimoto.gx@renesas.com
Link: https://lore.kernel.org/r/871racbx0w.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87h7ionc8s.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck warning:
sound/soc/soc-core.c:2784:6: style: Condition '!num_routes' is always
false [knownConditionTrueFalse]
if (!num_routes) {
^
sound/soc/soc-core.c:2777:17: note: Assuming that condition
'num_routes<0' is not redundant
if (num_routes < 0 || num_routes & 1) {
^
sound/soc/soc-core.c:2783:2: note: Compound assignment '/=', assigned
value is 0
num_routes /= 2;
^
sound/soc/soc-core.c:2784:6: note: Condition '!num_routes' is always
false
if (!num_routes) {
^
The documentation for of_property_count_string reads
"
* Returns the number of strings on
* success, -EINVAL if the property does not exist, -ENODATA if property
* does not have a value, and -EILSEQ if the string is not null-terminated
* within the length of the property data.
"
Since the case for num_routes == 0 is not possible, let's remove this
test.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@gmail.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20210416191144.27006-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A DAI link has 3 components:
* CPU
* platform
* codec(s)
A component is specified via:
* name
* of_node
* dai_name
In order to avoid confusion when building a sound card we disallow
matching by both name and of_node (1).
soc_check_tplg_fes allows overriding certain BE links by overriding
BE link name. This doesn't work well if BE link was specified via DT,
because we end up with a link with both name and of_node specified
which is conflicting with (1).
In order to fix this we need to:
* override of_node if component was specified via DT
* override name, otherwise.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20210414101212.65573-1-daniel.baluta@oss.nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We don't need to mind freeing for rtd,
because it was created from devm_kzalloc(dev, xxx) which is rtd->dev.
This means, if rtd->dev was freed, rtd will be also freed
automatically.
soc_new_pcm_runtime(...)
{
...
rtd = devm_kzalloc(dev, ...);
rtd->dev = dev;
...
}
This explanation was missing at soc_free_pcm_runtime() comment.
This patch indicates it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87sg4dxldn.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
All snd_soc_component_xxx() and snd_soc_pcm_component_xxx() itself
indicate error message if failed.
Its caller doesn't need to indicate duplicated error message.
This patch removes it.
All snd_soc_component_xxx() indicate error message if failed.
Its caller doesn't need to indicate duplicated error message.
This patch removes it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/878s6puta6.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When DMI information is not present, trying to assign the card long
name results in the following warning.
WARNING KERN tegra-audio-graph-card sound: ASoC: no DMI vendor name!
The initial solution suggested was to test if the card device is an
ACPI one. This causes a regression visible to userspace on all Intel
platforms, with UCM unable to load card profiles based on DMI
information: the card devices are not necessarily ACPI ones, e.g. when
the parent creates platform devices on Intel devices.
To fix this problem, this patch exports the existing dmi_available
variable and tests it in the ASoC core.
Fixes: c014170408 ("ASoC: soc-core: Prevent warning if no DMI table is present")
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Jean Delvare <jdelvare@suse.de>
Link: https://lore.kernel.org/r/20210310193928.108850-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The pointer to of_phandle_args passed to snd_soc_get_dai_name() and
of_xlate_dai_name() implementations is not modified. Since it is being
used only to translate passed OF node to a DAI name, it should not be
modified, so mark it as const for correctness and safer code.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20210221153024.453583-1-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Many systems do not use ACPI and hence do not provide a DMI table. On
non-ACPI systems a warning, such as the following, is printed on boot.
WARNING KERN tegra-audio-graph-card sound: ASoC: no DMI vendor name!
The variable 'dmi_available' is not exported and so currently cannot be
used by kernel modules without adding an accessor. However, it is
possible to use the function is_acpi_device_node() to determine if the
sound card is an ACPI device and hence indicate if we expect a DMI table
to be present. Therefore, call is_acpi_device_node() to see if we are
using ACPI and only parse the DMI table if we are booting with ACPI.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20210303115526.419458-1-jonathanh@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Auxiliary Bus support tag for 5.11-rc1
This is a signed tag for other subsystems to be able to pull in the
auxiliary bus support into their trees for the 5.11-rc1 merge.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "prefix" can be defined in DAI link node or it can be specified as
part of the component node itself. Currently "sound-name-prefix" defined
in a component is not taking effect. Actually the property is not getting
parsed. It can be fixed by parsing "sound-name-prefix" property whenever
"prefix" is missing in DAI link Codec node.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Link: https://lore.kernel.org/r/1604329814-24779-2-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current fmt_single_name code limits maximum name of a DAI or component
to 32 bytes. On some systems corresponding device names might be longer
than that (e.g.
17300000.remoteproc:glink-edge:apr:apr-service@8:routing). This will
result in duplicate DAI/component names. Rewrite fmt_single_name() to
remove such length limitations.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20200827205100.1479331-1-dmitry.baryshkov@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 25612477d2 ("ASoC: soc-dai: set dai_link dpcm_ flags with a helper")
added snd_soc_dai_link_set_capabilities().
But it is using snd_soc_find_dai() (A) which is required client_mutex (B).
And client_mutex is soc-core.c local.
struct snd_soc_dai *snd_soc_find_dai(xxx)
{
...
(B) lockdep_assert_held(&client_mutex);
...
}
void snd_soc_dai_link_set_capabilities(xxx)
{
...
for_each_pcm_streams(direction) {
...
for_each_link_cpus(dai_link, i, cpu) {
(A) dai = snd_soc_find_dai(cpu);
...
}
...
for_each_link_codecs(dai_link, i, codec) {
(A) dai = snd_soc_find_dai(codec);
...
}
}
...
}
Because of these background, we will get WARNING if .config has CONFIG_LOCKDEP.
WARNING: CPU: 2 PID: 53 at sound/soc/soc-core.c:814 snd_soc_find_dai+0xf8/0x100
CPU: 2 PID: 53 Comm: kworker/2:1 Not tainted 5.7.0-rc1+ #328
Hardware name: Renesas H3ULCB Kingfisher board based on r8a77951 (DT)
Workqueue: events deferred_probe_work_func
pstate: 60000005 (nZCv daif -PAN -UAO)
pc : snd_soc_find_dai+0xf8/0x100
lr : snd_soc_find_dai+0xf4/0x100
...
Call trace:
snd_soc_find_dai+0xf8/0x100
snd_soc_dai_link_set_capabilities+0xa0/0x16c
graph_dai_link_of_dpcm+0x390/0x3c0
graph_for_each_link+0x134/0x200
graph_probe+0x144/0x230
platform_drv_probe+0x5c/0xb0
really_probe+0xe4/0x430
driver_probe_device+0x60/0xf4
snd_soc_find_dai() will be used from (X) CPU/Codec/Platform driver with
mutex lock, and (Y) Card driver without mutex lock.
This snd_soc_dai_link_set_capabilities() is for Card driver,
this means called without mutex.
This patch adds snd_soc_find_dai_with_mutex() to solve it.
Fixes: 25612477d2 ("ASoC: soc-dai: set dai_link dpcm_ flags with a helper")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87blixvuab.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
simple-card.c and meson-card-utils.c use pretty much the same
helper function to parse auxiliary devices from the device tree.
Make it easier for other drivers to parse these from the device tree
as well by adding a shared helper function to soc-core.c.
snd_soc_of_parse_aux_devs() is pretty much a copy of
meson_card_add_aux_devices() from meson-card-utils.c
with two minor changes:
- Make property name configurable as parameter
- Change dev_err() message slightly for consistency with other
error messages in soc-core.c
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20200801100257.22658-1-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
