commit 25de4ce5ed upstream.
There is a timer wrap issue on dra7 for the ARM architected timer.
In a typical clock configuration the timer fails to wrap after 388 days.
To work around the issue, we need to use timer-ti-dm percpu timers instead.
Let's configure dmtimer3 and 4 as percpu timers by default, and warn about
the issue if the dtb is not configured properly.
Let's do this as a single patch so it can be backported to v5.8 and later
kernels easily. Note that this patch depends on earlier timer-ti-dm
systimer posted mode fixes, and a preparatory clockevent patch
"clocksource/drivers/timer-ti-dm: Prepare to handle dra7 timer wrap issue".
For more information, please see the errata for "AM572x Sitara Processors
Silicon Revisions 1.1, 2.0":
https://www.ti.com/lit/er/sprz429m/sprz429m.pdf
The concept is based on earlier reference patches done by Tero Kristo and
Keerthy.
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <kristo@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210323074326.28302-3-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9ba585cc5b ]
UniPhier PXs2 boards have RTL8211E ethernet phy, and the phy have the RX/TX
delays of RGMII interface using pull-ups on the RXDLY and TXDLY pins.
After the commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e rx/tx
delay config"), the delays are working correctly, however, "rgmii" means
no delay and the phy doesn't work. So need to set the phy-mode to
"rgmii-id" to show that RX/TX delays are enabled.
Fixes: e3cc931921 ("ARM: dts: uniphier: add AVE ethernet node")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d5d46a1ad ]
The si7021 was incorrectly placed at 0x20 on i2c bus 7. It is at 0x40.
Fixes: 9c44db7096 ("ARM: dts: aspeed: rainier: Add i2c devices")
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a1429f3d30 ]
Modify usart 2 & 3 pins to allow wake up from low power mode while the
hardware flow control is activated. UART RTS pin need to stay configure
in idle mode to receive characters in order to wake up.
Fixes: 842ed898a7 ("ARM: dts: stm32: add usart2, usart3 and uart7 pins in stm32mp15-pinctrl")
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8987efbb17 ]
The Maxim PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Additionally, the interrupt line is shared so using level sensitive
interrupt is here especially important to avoid races.
Fixes: c61248afa8 ("ARM: dts: Add max77686 RTC interrupt to cros5250-common")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212534.216197-9-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f6368c6056 ]
The Maxim PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Additionally, the interrupt line is shared so using level sensitive
interrupt is here especially important to avoid races.
Fixes: 47580e8d94 ("ARM: dts: Specify MAX77686 pmic interrupt for exynos5250-smdk5250")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212534.216197-8-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6503c568e9 ]
The Maxim PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Additionally, the interrupt line is shared so using level sensitive
interrupt is here especially important to avoid races.
Fixes: eea6653aae ("ARM: dts: Enable PMIC interrupts for exynos4412-odroid-common")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212534.216197-6-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e52dcd6e70 ]
The Maxim PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Additionally, the interrupt line is shared so using level sensitive
interrupt is here especially important to avoid races.
Fixes: 15dfdfad2d ("ARM: dts: Add basic dts for Exynos4412-based Trats 2 board")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212534.216197-5-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15107e443a ]
The Maxim MUIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Additionally, the interrupt line is shared so using level sensitive
interrupt is here especially important to avoid races.
Fixes: 7eec126675 ("ARM: dts: Add Maxim 77693 PMIC to exynos4412-trats2")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212534.216197-4-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a45f33bd3 ]
The Maxim fuel gauge datasheets describe the interrupt line as active
low with a requirement of acknowledge from the CPU. The falling edge
interrupt will mostly work but it's not correct.
Fixes: e8614292cd ("ARM: dts: Add Maxim 77693 fuel gauge node for exynos4412-trats2")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212534.216197-3-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4679980213 ]
The Maxim fuel gauge datasheets describe the interrupt line as active
low with a requirement of acknowledge from the CPU. The falling edge
interrupt will mostly work but it's not correct.
Fixes: 8620cc2f99 ("ARM: dts: exynos: Add devicetree file for the Galaxy S2")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212534.216197-1-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
Update the symbol as well as the alias so that other overlays will
then be applied against the right node.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
[ Upstream commit aeceecd40d ]
The TVK1281618 R3 sensors are different from the R2 board,
some incorrectness is fixed and some new sensors added, we
also rename the nodes appropriately with accelerometer@
etc.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b27b9689e1 ]
Rename avdd supply to vdda of the touchscreen node. The old supply name
was incorrect.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
This is a simple overlay based on the simple-audio-card and the dmic
codec. It has the speciality that it is configured to use the codec
as a master I2S device. It works for example with the Si468x DAB
receiver on the uGreen DABBoard.
See: https://github.com/raspberrypi/linux/issues/4304
Signed-off-by: Christoph Orth <c.orth@ugreen.eu>
[ Upstream commit a1ebdb3741 ]
Also some omap3 devices like n900 seem to have eMMC and micro-sd swapped
around with commit 21b2cec61c ("mmc: Set PROBE_PREFER_ASYNCHRONOUS for
drivers that existed in v4.4").
Let's fix the issue with aliases as discussed on the mailing lists. While
the mmc aliases should be board specific, let's first fix the issue with
minimal changes.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
There is no reason not to support multiple gpio-shutdown signals,
so add the necessary __override__ magic.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The VEC's DAC on BCM2711 is slightly different compared to the one on
BCM283x and needs different configuration. In particular, bit 3
(mask 0x8) switches the BCM2711 DAC input to "self-test input data",
which makes the output unusable. Separating two compatible variants in
devicetrees and the DRM driver was therefore necessary.
The configurations used for both variants have been borrowed from
Raspberry Pi (model 3B for BCM283x, 4B for BCM2711) firmware defaults.
Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
The VEC has a different address (0x7ec13000) on the BCM2711 (used in
e.g. Raspberry Pi 4) compared to BCM238x (e.g. Pi 3 and earlier). This
was erroneously not taken account for.
Definition of the VEC in the devicetrees had to be moved from
bcm283x.dtsi to bcm2711.dtsi and bcm2835-common.dtsi to allow for this
differentiation.
Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
Extend the spi-rtc overlay to support the ds3232 and ds3234 RTCs, as
well as adding parameters to select difference SPI controllers and
chip selects.
N.B. The default CS is now active-low - use the "cs_high" parameter to
override this.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
[ Upstream commit 77335a0401 ]
Fix moving mmc devices with dts aliases as discussed on the lists.
Without this we now have internal eMMC mmc1 show up as mmc2 compared
to the earlier order of devices.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 140a776833 ]
We have a duplicate legacy clock defined for sha2md5_fck that can
sometimes race with clk_disable() with the dts configured clock
for OMAP4_SHA2MD5_CLKCTRL when unused clocks are disabled during
boot causing an "Unhandled fault: imprecise external abort".
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Credit to forum member gizmomouse on
https://www.raspberrypi.org/forums/viewtopic.php?f=98&t=253912 and
Andrey Vostrukhin of Harlab for these overlays.
See https://github.com/harlab/CM4_LCD_LT070ME05000 for
schematics and docs for the adapter board to connect this panel which
is found in the Asus/Google 2013 Nexus 7" tablet and therefore
relatively easily available.
Note that this uses 4 DSI data lanes, and therefore MUST be used
with DISP1 on a Compute Module. It can not be used on a standard
Pi.
There are two versions of the adapter board. V1 connects the
display controls to Pi GPIOs, whilst v2 uses an I2C GPIO expander
so needs no additional connections beyond the FFC and power.
The touchscreen overlay for these panels varies, so that part
is not configured.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
[ Upstream commit f57011e72f ]
Setting the vmmc supplies is crucial since otherwise the supplying
regulators get disabled and the SD interfaces are no longer powered
which leads to system failures if the system is booted from that SD
interface.
Fixes: 1e44d3f880 ("ARM i.MX6Q: dts: Enable I2C1 with EEPROM and PMIC on Phytec phyFLEX-i.MX6 Ouad module")
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a26c56ae67 upstream.
Use the `marvell,reg-init` DT property to configure the LED[2]/INTn pin
of the Marvell 88E1514 ethernet PHY on Turris Omnia into interrupt mode.
Without this the pin is by default in LED[2] mode, and the Marvell PHY
driver configures LED[2] into "On - Link, Blink - Activity" mode.
This fixes the issue where the pca9538 GPIO/interrupt controller (which
can't mask interrupts in HW) received too many interrupts and after a
time started ignoring the interrupt with error message:
IRQ 71: nobody cared
There is a work in progress to have the Marvell PHY driver support
parsing PHY LED nodes from OF and registering the LEDs as Linux LED
class devices. Once this is done the PHY driver can also automatically
set the pin into INTn mode if it does not find LED[2] in OF.
Until then, though, we fix this via `marvell,reg-init` DT property.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reported-by: Rui Salvaterra <rsalvaterra@gmail.com>
Fixes: 26ca8b52d6 ("ARM: dts: add support for Turris Omnia")
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: <stable@vger.kernel.org>
Tested-by: Rui Salvaterra <rsalvaterra@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9bbce32a20 ]
Without DT aliases, the numbering of mmc interfaces is unpredictable.
Adding them makes it possible to refer to devices consistently. The
popular suggestion to use UUIDs obviously doesn't work with a blank
device fresh from the factory.
See commit fa2d0aa969 ("mmc: core: Allow setting slot index via
device tree alias") for more discussion.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Neither CM4 nor Pi 400 have appeared upstream yet, and as a result
they have missed out on improvements to the Pi 4B platform.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
ARM: dts: Bring bcm2711-rpi-400.dts up-to-date
Pi 400 support has not appeared upstream yet, and as a result it has
missed out on improvements to the other Pi 4 platforms.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
[ Upstream commit e4817a1b6b ]
For NAND Ecc layout, there is a dependency from old kernel's nand driver
setting and current. if old kernel use 4 bit ecc , we should use 4 bit
in new kernel either. else will run into following error at filesystem
mounting.
So, enable fsl,use-minimum-ecc from device tree, to fix this mismatch
[ 9.449265] ubi0: scanning is finished
[ 9.463968] ubi0 warning: ubi_io_read: error -74 (ECC error) while reading
22528 bytes from PEB 513:4096, read only 22528 bytes, retry
[ 9.486940] ubi0 warning: ubi_io_read: error -74 (ECC error) while reading
22528 bytes from PEB 513:4096, read only 22528 bytes, retry
[ 9.509906] ubi0 warning: ubi_io_read: error -74 (ECC error) while reading
22528 bytes from PEB 513:4096, read only 22528 bytes, retry
[ 9.532845] ubi0 error: ubi_io_read: error -74 (ECC error) while reading
22528 bytes from PEB 513:4096, read 22528 bytes
Fixes: f9ecf10cb8 ("ARM: dts: imx6ull: add MYiR MYS-6ULX SBC")
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 221c3a09dd upstream.
Fix the phy address to 7 for Ethernet PHY on SAMA5D27 SOM1. No
connection established if phy address 0 is used.
The board uses the 24 pins version of the KSZ8081RNA part, KSZ8081RNA
pin 16 REFCLK as PHYAD bit [2] has weak internal pull-down. But at
reset, connected to PD09 of the MPU it's connected with an internal
pull-up forming PHYAD[2:0] = 7.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Fixes: 2f61929eb1 ("ARM: dts: at91: at91-sama5d27_som1: fix PHY ID")
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: <stable@vger.kernel.org> # 4.14+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1. Reduce the delay between RELAY1 and RELAY2 to 1000ms.
2. Rename the states to simplify LED control by an external script.
3. Claim all the required GPIOs, enabling pull-ups on the input.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
