[ Upstream commit a1429f3d30 ]
Modify usart 2 & 3 pins to allow wake up from low power mode while the
hardware flow control is activated. UART RTS pin need to stay configure
in idle mode to receive characters in order to wake up.
Fixes: 842ed898a7 ("ARM: dts: stm32: add usart2, usart3 and uart7 pins in stm32mp15-pinctrl")
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Add support for Seeed Studio's stm32mp157c odyssey board.
Board consists of SoM with stm32mp157c with 4GB eMMC and 512 MB DDR3 RAM
and carrier board with USB and ETH interfaces, SD card connector,
wifi and BT chip AP6236.
In this patch only basic kernel boot is supported and interfacing
SD card and on-board eMMC.
Signed-off-by: Marcin Sloniewski <marcin.sloniewski@gmail.com>
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Move spi4_pins_a nodes from pinctrl_z to pinctrl as the associated pins
are not in BANK Z.
Fixes: 498a701498 ("ARM: dts: stm32: Add missing pinctrl entries for STM32MP15")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Adds usart2_pins_c, usart3_pins_b, usart3_pins_c and uart7_pins_c pins
configurations in stm32mp15-pinctrl.
- usart2_pins_c pins are connected to Bluetooth chip on dk2 board.
- usart3_pins_b pins are connected to GPIO expansion connector on evx board.
- usart3_pins_c pins are connected to GPIO expansion connector on dkx board.
- uart7_pins_c pins are connected to Arduino Uno connector on dkx board.
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Sleep pin configuration is refined for low power modes:
- "sleep" (no wakeup & console suspend enabled): put pins in analog state
to optimize power
- "idle" (wakeup capability): keep Rx pin in alternate function
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
These pinctrl definitions will be used by Stinger96/IoTBox boards
from Shiratech.
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The Linux Automation MC-1 is a SBC built around the Octavo Systems
OSD32MP15x SiP. The SiP features up to 1 GB DDR3 RAM, EEPROM and
a PMIC. The board has eMMC and a SD slot for storage and GbE
for both connectivity and power.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
While all sleep pinctrl group labels now follow a fixed naming scheme,
node _names_ for these groups don't:
- Some use ${dev}-[0-9], where the suffix is the normal group suffix + 1
- Some use ${dev}-sleep-[0-9], where suffix is the normal group suffix
- The <dc node uses ${dev}-[a-z]-[0-9], where the letter matches the
phandle and the number suffix is the normal group's suffix + 1
For uniformity, standardize on using ${dev}-[0-9]+ for all normal
pinctrl groups and ${dev}-sleep-[0-9]+ for all sleep pinctrl groups.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Some labels follow the *_sleep_pins_* naming scheme, but some also use
*_pins_sleep_*. Because most labels use the former and for uniformity
with variants like sdmmc1_b4_pins_a and sdmmc1_dir_pins_a, adopt the
*_sleep_pins_* scheme throughout.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add pinctrl definition for USB High-Speed OTG ID pin and USB Full-Speed OTG
DP and DM lines that can be used on stm32mp15.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
In order to cover the STM32MP15 SOCs family this commit updates pinctrl
file names (group definition and packages files).
This family includes: STM32MP151, STM32MP153 and STM32MP157.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
