[ Upstream commit dcabb06bf1 ]
UniPhier LD20 and PXs3 boards have RTL8211E ethernet phy, and the phy have
the RX/TX delays of RGMII interface using pull-ups on the RXDLY and TXDLY
pins.
After the commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e rx/tx
delay config"), the delays are working correctly, however, "rgmii" means
no delay and the phy doesn't work. So need to set the phy-mode to
"rgmii-id" to show that RX/TX delays are enabled.
Fixes: c73730ee4c ("arm64: dts: uniphier: add AVE ethernet node")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e526cb03e2 ]
The last cell of 'gpio-ranges' should be number of GPIO pins, and in
case of qcom platform it should match msm_pinctrl_soc_data.ngpio rather
than msm_pinctrl_soc_data.ngpio - 1.
This fixes the problem that when the last GPIO pin in the range is
configured with the following call sequence, it always fails with
-EPROBE_DEFER.
pinctrl_gpio_set_config()
pinctrl_get_device_gpio_range()
pinctrl_match_gpio_range()
Fixes: 16951b490b ("arm64: dts: qcom: sm8250: Add TLMM pinctrl node")
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20210303033106.549-4-shawn.guo@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de3abdf3d1 ]
The last cell of 'gpio-ranges' should be number of GPIO pins, and in
case of qcom platform it should match msm_pinctrl_soc_data.ngpio rather
than msm_pinctrl_soc_data.ngpio - 1.
This fixes the problem that when the last GPIO pin in the range is
configured with the following call sequence, it always fails with
-EPROBE_DEFER.
pinctrl_gpio_set_config()
pinctrl_get_device_gpio_range()
pinctrl_match_gpio_range()
Fixes: e13c6d144f ("arm64: dts: qcom: sm8150: Add base dts file")
Cc: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20210303033106.549-3-shawn.guo@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 02058fc383 ]
The last cell of 'gpio-ranges' should be number of GPIO pins, and in
case of qcom platform it should match msm_pinctrl_soc_data.ngpio rather
than msm_pinctrl_soc_data.ngpio - 1.
This fixes the problem that when the last GPIO pin in the range is
configured with the following call sequence, it always fails with
-EPROBE_DEFER.
pinctrl_gpio_set_config()
pinctrl_get_device_gpio_range()
pinctrl_match_gpio_range()
Fixes: bc2c806293 ("arm64: dts: qcom: sdm845: Add gpio-ranges to TLMM node")
Cc: Evan Green <evgreen@chromium.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20210303033106.549-2-shawn.guo@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a362b0cc94 ]
Commit 99e71c0292 ("arm64: dts: imx8mq-librem5: Don't mark buck3 as always on")
removed always-on marking from GPU regulator, which is great for power
saving - however it introduces additional i2c0 traffic which can be deadly
for devices from the Dogwood batch.
To workaround the i2c0 shutdown issue on Dogwood, this commit marks
buck3 as always-on again - but only for Dogwood (r3).
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4d09ccc4a8 ]
Commit 941432d007 ("arm64: dts: allwinner: Drop non-removable from
SoPine/LTS SD card") enabled the card detect GPIO for the SOPine module,
along the way with the Pine64-LTS, which share the same base .dtsi.
This was based on the observation that the Pine64-LTS has as "push-push"
SD card socket, and that the schematic mentions the card detect GPIO.
After having received two reports about failing SD card access with that
patch, some more research and polls on that subject revealed that there
are at least two different versions of the Pine64-LTS out there:
- On some boards (including mine) the card detect pin is "stuck" at
high, regardless of an microSD card being inserted or not.
- On other boards the card-detect is working, but is active-high, by
virtue of an explicit inverter circuit, as shown in the schematic.
To cover all versions of the board out there, and don't take any chances,
let's revert the introduction of the active-low CD GPIO, but let's use
the broken-cd property for the Pine64-LTS this time. That should avoid
regressions and should work for everyone, even allowing SD card changes
now.
The SOPine card detect has proven to be working, so let's keep that
GPIO in place.
Fixes: 941432d007 ("arm64: dts: allwinner: Drop non-removable from SoPine/LTS SD card")
Reported-by: Michael Weiser <michael.weiser@gmx.de>
Reported-by: Daniel Kulesz <kuleszdl@posteo.org>
Suggested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Michael Weiser <michael.weiser@gmx.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210414104740.31497-1-andre.przywara@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a2f6e69e9 ]
Although every Beelink GS1 seems to have external 32768 Hz oscillator,
it works only on one from four tested. There are more reports of RTC
issues elsewhere, like Armbian forum.
One Beelink GS1 owner read RTC osc status register on Android which
shipped with the box. Reported value indicated problems with external
oscillator.
In order to fix RTC and related issues (HDMI-CEC and suspend/resume with
Crust) on all boards, switch to internal oscillator.
Fixes: 32507b8681 ("arm64: dts: allwinner: h6: Move ext. oscillator to board DTs")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210330184218.279738-1-jernej.skrabec@siol.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3dd4ce4185 ]
Commit 941432d007 ("arm64: dts: allwinner: Drop non-removable from
SoPine/LTS SD card") enabled the card detect GPIO for the SOPine module,
along the way with the Pine64-LTS, which share the same base .dtsi.
However while both boards indeed have a working CD GPIO on PF6, the
polarity is different: the SOPine modules uses a "push-pull" socket,
which has an active-high switch, while the Pine64-LTS use the more
traditional push-push socket and the common active-low switch.
Fix the polarity in the sopine.dtsi, and overwrite it in the LTS
board .dts, to make the SD card work again on systems using SOPine
modules.
Fixes: 941432d007 ("arm64: dts: allwinner: Drop non-removable from SoPine/LTS SD card")
Reported-by: Ashley <contact@victorianfox.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210316144219.5973-1-andre.przywara@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5cfad4f458 ]
Fix address of the pad control register
(IOMUXC_SW_PAD_CTL_PAD_SD1_DATA0) for SD1_DATA0_GPIO2_IO2. This seems
to be a typo but it leads to an exception when pinctrl is applied due to
wrong memory address access.
Signed-off-by: Oliver Stäbler <oliver.staebler@bytesatwork.ch>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Fixes: c1c9d41319 ("dt-bindings: imx: Add pinctrl binding doc for imx8mm")
Fixes: 748f908cc8 ("arm64: add basic DTS for i.MX8MQ")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ba8da03fa7 upstream.
Crypto engine (CAAM) on LS1012A platform is configured HW-coherent,
mark accordingly the DT node.
Lack of "dma-coherent" property for an IP that is configured HW-coherent
can lead to problems, similar to what has been reported for LS1046A.
Cc: <stable@vger.kernel.org> # v4.12+
Fixes: 85b85c5695 ("arm64: dts: ls1012a: add crypto node")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a9d9bfcadf ]
The partition called "u-boot" in reality contains TF-A and U-Boot, and
TF-A is before U-Boot.
Rename this parition to "a53-firmware" to avoid confusion for users,
since they cannot simply build U-Boot from U-Boot repository and flash
the resulting image there. Instead they have to build the firmware with
the sources from the mox-boot-builder repository [1] and flash the
a53-firmware.bin binary there.
[1] https://gitlab.nic.cz/turris/mox-boot-builder
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes: 7109d817db ("arm64: dts: marvell: add DTS for Turris Mox")
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c6433083f5 ]
The gmac2phy is integrated with the PHY within the SoC. Any properties
related to this integration can be included in the .dtsi file, instead
of having board dts files specify them separately.
Add the clock_in_out property to specify the direction of the PHY clock.
This is the minimum required to have gmac2phy working on Linux. Other
examples include assigned-clocks, assigned-clock-rates, and
assigned-clock-parents properties, but the hardware default plus the
implementation requesting the appropriate clock rate also works.
Fixes: 9c4cc910fe ("ARM64: dts: rockchip: Add gmac2phy node support for rk3328")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20210117100710.4857-2-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3716a583fe ]
When the BMC150 accelerometer/magnetometer was added to the device tree,
the sensors were working without specifying any regulator supplies,
likely because the regulators were on by default and then never turned off.
For some reason, this is no longer the case for pm8916_l17, which prevents
the sensors from working in some cases.
Now that the bmc150_accel/bmc150_magn drivers can enable necessary
regulators, declare the necessary regulator supplies to make the sensors
work again.
Fixes: 079f81acf1 ("arm64: dts: qcom: msm8916-samsung-a2015: Add accelerometer/magnetometer")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210111175358.97171-1-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 948c657cc4 ]
In contrast to the H6 (and later) manuals, the A64 datasheet does not
specify any limitations in the maximum possible frequency for eMMC
controllers.
However experimentation has found that a 150 MHz limit similar to other
SoCs and also the MMC0 and MMC1 controllers on the A64 seems to exist
for the MMC2 controller.
Limit the frequency for the MMC2 controller to 150 MHz in the SoC .dtsi.
The Pinebook seems to be the an odd exception, since it apparently seems
to work with 200 MHz as well, so overwrite this in its board .dts file.
Tested on a Pine64-LTS: 200 MHz HS-200 fails, 150 MHz HS-200 works.
Fixes: 22be992fae ("arm64: allwinner: a64: Increase the MMC max frequency")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210113152630.28810-7-andre.przywara@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cfe6c487b9 ]
The H6 manual explicitly lists a frequency limit of 150 MHz for the bus
frequency of the MMC controllers. So far we had no explicit limits in the
DT, which limited eMMC to the spec defined frequencies, or whatever the
driver defines (both Linux and FreeBSD use 52 MHz here).
Put those maximum frequencies in the SoC .dtsi, to allow higher speed
modes (which still would need to be explicitly enabled, per board).
Tested with an eMMC using HS-200 on a Pine H64. Running at the spec'ed
200 MHz indeed fails with I/O errors, but 150 MHz seems to work stably.
Fixes: 8f54bd1595 ("arm64: allwinner: h6: add device tree nodes for MMC controllers")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210113152630.28810-6-andre.przywara@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 941432d007 ]
The SD card on the SoPine SoM module is somewhat concealed, so was
originally defined as "non-removable".
However there is a working card-detect pin (tested on two different
SoM versions), and in certain SoM base boards it might be actually
accessible at runtime.
Also the Pine64-LTS shares the SoPine base .dtsi, so inherited the
non-removable flag, even though the SD card slot is perfectly accessible
and usable there. (It turns out that just *my* board has a broken card
detect switch, so I originally thought CD wouldn't work on the LTS.)
Drop the "non-removable" flag to describe the SD card slot properly.
Fixes: c3904a2698 ("arm64: allwinner: a64: add DTSI file for SoPine SoM")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210113152630.28810-5-andre.przywara@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da2fb8457f ]
In recent Allwinner SoCs the first USB host controller (HCI0) shares
the first PHY with the MUSB controller. Probably to make this sharing
work, we were avoiding to declare this in the DT. This has two
shortcomings:
- U-Boot (which uses the same .dts) cannot use this port in host mode
without a PHY linked, so we were loosing one USB port there.
- It requires the MUSB driver to be enabled and loaded, although we
don't actually use it.
To avoid those issues, let's add this PHY link to the H6 .dtsi file.
After all PHY port 0 *is* connected to HCI0, so we should describe
it as this.
This makes it work in U-Boot, also improves compatiblity when no MUSB
driver is loaded (for instance in distribution installers).
Fixes: eabb3d424b ("arm64: dts: allwinner: h6: add USB2-related device nodes")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210113152630.28810-3-andre.przywara@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc72570747 ]
In recent Allwinner SoCs the first USB host controller (HCI0) shares
the first PHY with the MUSB controller. Probably to make this sharing
work, we were avoiding to declare this in the DT. This has two
shortcomings:
- U-Boot (which uses the same .dts) cannot use this port in host mode
without a PHY linked, so we were loosing one USB port there.
- It requires the MUSB driver to be enabled and loaded, although we
don't actually use it.
To avoid those issues, let's add this PHY link to the A64 .dtsi file.
After all PHY port 0 *is* connected to HCI0, so we should describe
it as this. Remove the part from the Pinebook DTS which already had
this property.
This makes it work in U-Boot, also improves compatiblity when no MUSB
driver is loaded (for instance in distribution installers).
Fixes: dc03a047df ("arm64: allwinner: a64: add EHCI0/OHCI0 nodes to A64 DTSI")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210113152630.28810-2-andre.przywara@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 826e6faf49 ]
Unlike most MSM8916 boards, samsung-a5u uses WCN3660B instead of
WCN3620 to support the 5 GHz band additionally.
WCN3660B has similar requirements as WCN3620, but it needs the XO
clock to run at 48 MHz instead of 19.2 MHz. So far it was possible
to describe that configuration using the qcom,wcn3680 compatible.
However, as of commit 8490987bdb ("wcn36xx: Hook and identify RF_IRIS_WCN3680"),
the wcn36xx driver will now use the qcom,wcn3680 compatible
to enable functionality specific to WCN3680. In particular,
WCN3680 supports 802.11ac, which is not available in WCN3660B.
Use the new qcom,wcn3660b compatible to describe the chip properly.
Fixes: 0d70519991 ("arm64: dts: msm8916-samsung-a5u: Override iris compatible")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210106102134.59801-4-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1fea2eb2f5 ]
The Samsung PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Fixes: 9589f7721e ("arm64: dts: Add S2MPS15 PMIC node on exynos7-espresso")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212903.216728-8-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e98e2367df ]
The Samsung PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Fixes: 01e5d23521 ("arm64: dts: exynos: Add dts file for Exynos5433-based TM2 board")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20201210212903.216728-7-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db030c5a96 ]
The Bluetooth chip is capable of operating at 4Mbps, but the
max-speed setting was on the UART node instead of the Bluetooth
node, so the chip didn't operate at the correct speed resulting
in choppy audio. Fix this by setting the max-speed in the proper
node.
Fixes: a1d8a344f1 ("arm64: dts: renesas: Introduce r8a774a1-beacon-rzg2m-kit")
Signed-off-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20201213183759.223246-3-aford173@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
