Introduce new capability - Low Latency Timestamping with Interrupt.
On supported devices, driver can request a single timestamp from FW
without polling the register afterwards. Instead, FW can issue
a dedicated interrupt when the timestamp was read from the PHY register
and its value is available to read from the register.
This eliminates the need of bottom half scheduling, which results in
minimal delay for timestamping.
For this mode, allocate TS indices sequentially, so that timestamps are
always completed in FIFO manner.
Co-developed-by: Yochai Hagvi <yochai.hagvi@intel.com>
Signed-off-by: Yochai Hagvi <yochai.hagvi@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Stop dividing the phase_offset value received from firmware. This fault
is present since the initial implementation.
The phase_offset value received from firmware is in 0.01ps resolution.
Dpll subsystem is using the value in 0.001ps, raw value is adjusted
before providing it to the user.
The user can observe the value of phase offset with response to
`pin-get` netlink message of dpll subsystem for an active pin:
$ ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/dpll.yaml \
--do pin-get --json '{"id":2}'
Where example of correct response would be:
{'board-label': 'C827_0-RCLKA',
'capabilities': 6,
'clock-id': 4658613174691613800,
'frequency': 1953125,
'id': 2,
'module-name': 'ice',
'parent-device': [{'direction': 'input',
'parent-id': 6,
'phase-offset': -216839550,
'prio': 9,
'state': 'connected'},
{'direction': 'input',
'parent-id': 7,
'phase-offset': -42930,
'prio': 8,
'state': 'connected'}],
'phase-adjust': 0,
'phase-adjust-max': 16723,
'phase-adjust-min': -16723,
'type': 'mux'}
Provided phase-offset value (-42930) shall be divided by the user with
DPLL_PHASE_OFFSET_DIVIDER to get actual value of -42.930 ps.
Before the fix, the response was not correct:
{'board-label': 'C827_0-RCLKA',
'capabilities': 6,
'clock-id': 4658613174691613800,
'frequency': 1953125,
'id': 2,
'module-name': 'ice',
'parent-device': [{'direction': 'input',
'parent-id': 6,
'phase-offset': -216839,
'prio': 9,
'state': 'connected'},
{'direction': 'input',
'parent-id': 7,
'phase-offset': -42,
'prio': 8,
'state': 'connected'}],
'phase-adjust': 0,
'phase-adjust-max': 16723,
'phase-adjust-min': -16723,
'type': 'mux'}
Where phase-offset value (-42), after division
(DPLL_PHASE_OFFSET_DIVIDER) would be: -0.042 ps.
Fixes: 8a3a565ff2 ("ice: add admin commands to access cgu configuration")
Fixes: 90e1c90750 ("ice: dpll: implement phase related callbacks")
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Refactor the ice driver to use FIELD_GET() for mask and shift reads,
which reduces lines of code and adds clarity of intent.
This code was generated by the following coccinelle/spatch script and
then manually repaired.
@get@
constant shift,mask;
type T;
expression a;
@@
-(((T)(a) & mask) >> shift)
+FIELD_GET(mask, a)
and applied via:
spatch --sp-file field_prep.cocci --in-place --dir \
drivers/net/ethernet/intel/
CC: Alexander Lobakin <aleksander.lobakin@intel.com>
Cc: Julia Lawall <Julia.Lawall@inria.fr>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Refactor ice driver to use FIELD_PREP(), which reduces lines of code
and adds clarity of intent.
This code was generated by the following coccinelle/spatch script and
then manually repaired.
Several places I changed to OR into a single variable with |= instead of
using a multi-line statement with trailing OR operators, as it
(subjectively) makes the code clearer.
A local variable vmvf_and_timeout was created and used to avoid multiple
logical ORs being __le16 converted, which shortened some lines and makes
the code cleaner.
Also clean up a couple of places where conversions were made to have the
code read more clearly/consistently.
@prep2@
constant shift,mask;
type T;
expression a;
@@
-(((T)(a) << shift) & mask)
+FIELD_PREP(mask, a)
@prep@
constant shift,mask;
type T;
expression a;
@@
-((T)((a) << shift) & mask)
+FIELD_PREP(mask, a)
Cc: Julia Lawall <Julia.Lawall@inria.fr>
CC: Alexander Lobakin <aleksander.lobakin@intel.com>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Users want the ability to debug FW issues by retrieving the
FW logs from the E8xx devices. Use debugfs to allow the user to
configure the log level and number of messages for FW logging.
If FW logging is supported on the E8xx then the file 'fwlog' will be
created under the PCI device ID for the ice driver. If the file does not
exist then either the E8xx doesn't support FW logging or debugfs is not
enabled on the system.
One thing users want to do is control which events are reported. The
user can read and write the 'fwlog/modules/<module name>' to get/set
the log levels. Each module in the FW that supports logging ht as a file
under 'fwlog/modules' that supports reading (to see what the current log
level is) and writing (to change the log level).
The format to set the log levels for a module are:
# echo <log level> > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/modules/<module>
The supported log levels are:
* none
* error
* warning
* normal
* verbose
Each level includes the messages from the previous/lower level
The modules that are supported are:
* general
* ctrl
* link
* link_topo
* dnl
* i2c
* sdp
* mdio
* adminq
* hdma
* lldp
* dcbx
* dcb
* xlr
* nvm
* auth
* vpd
* iosf
* parser
* sw
* scheduler
* txq
* rsvd
* post
* watchdog
* task_dispatch
* mng
* synce
* health
* tsdrv
* pfreg
* mdlver
* all
The module 'all' is a special module which allows the user to read or
write to all of the modules.
The following example command would set the DCB module to the 'normal'
log level:
# echo normal > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/modules/dcb
If the user wants to set the DCB, Link, and the AdminQ modules to
'verbose' then the commands are:
# echo verbose > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/modules/dcb
# echo verbose > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/modules/link
# echo verbose > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/modules/adminq
If the user wants to set all modules to the 'warning' level then the
command is:
# echo warning > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/modules/all
If the user wants to disable logging for a module then they can set the
level to 'none'. An example setting the 'watchdog' module is:
# echo none > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/modules/watchdog
If the user wants to see what the log level is for a specific module
then the command is:
# cat /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/modules/dcb
This will return the log level for the DCB module. If the user wants to
see the log level for all the modules then the command is:
# cat /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/modules/all
Writing to the module file will update the configuration, but NOT enable the
configuration (that is a separate command).
In addition to configuring the modules, the user can also configure the
number of log messages (nr_messages) to include in a single Admin Receive
Queue (ARQ) event.The range is 1-128 (1 means push every log message, 128
means push only when the max AQ command buffer is full). The suggested
value is 10.
To see/change the resolution the user can read/write the
'fwlog/nr_messages' file. An example changing the value to 50 is
# echo 50 > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/nr_messages
To see the current value of 'nr_messages' then the command is:
# cat /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/nr_messages
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The FW logging code doesn't work because there is no way to set
cq_ena or uart_ena so remove the code. This code is the original
(v1) way of FW logging so it should be replaced with the v2 way.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The recent support for DPLL introduced by commit 8a3a565ff2 ("ice: add
admin commands to access cgu configuration") and commit d7999f5ea6 ("ice:
implement dpll interface to control cgu") broke linking the ice driver if
CONFIG_PTP_1588_CLOCK=n:
ld: vmlinux.o: in function `ice_init_feature_support':
(.text+0x8702b8): undefined reference to `ice_is_phy_rclk_present'
ld: (.text+0x8702cd): undefined reference to `ice_is_cgu_present'
ld: (.text+0x8702d9): undefined reference to `ice_is_clock_mux_present_e810t'
ld: vmlinux.o: in function `ice_dpll_init_info_direct_pins':
ice_dpll.c:(.text+0x894167): undefined reference to `ice_cgu_get_pin_freq_supp'
ld: ice_dpll.c:(.text+0x894197): undefined reference to `ice_cgu_get_pin_name'
ld: ice_dpll.c:(.text+0x8941a8): undefined reference to `ice_cgu_get_pin_type'
ld: vmlinux.o: in function `ice_dpll_update_state':
ice_dpll.c:(.text+0x894494): undefined reference to `ice_get_cgu_state'
ld: vmlinux.o: in function `ice_dpll_init':
(.text+0x8953d5): undefined reference to `ice_get_cgu_rclk_pin_info'
The first commit broke things by calling functions in
ice_init_feature_support that are compiled as part of ice_ptp_hw.o,
including:
* ice_is_phy_rclk_present
* ice_is_clock_mux_present_e810t
* ice_is_cgU_present
The second commit continued the break by calling several CGU functions
defined in ice_ptp_hw.c in the DPLL code.
Because the ice_dpll.c file is compiled unconditionally, it will not
link when CONFIG_PTP_1588_CLOCK=n.
It might be possible to break this dependency and expose those functions
without CONFIG_PTP_1588_CLOCK, but that is not clear to me.
For the DPLL case, simply compile ice_dpll.o only when we have
CONFIG_PTP_1588_CLOCK. Add stub no-op implementation of ice_dpll_init() and
ice_dpll_uninit() when CONFIG_PTP_1588_CLOCK=n into ice_dpll.h
The other functions are part of checking the netlist to see if hardware
features are enabled. These checks don't really belong in ice_ptp_hw.c, and
make more sense as part of the ice_common.c file. We already have
ice_is_gps_in_netlist() in ice_common.c which is doing a similar check.
Move the functions into ice_common.c and rename them to have the similar
postfix of "in_netlist()" to be more expressive of what they are actually
checking.
This also makes the ice_find_netlist_node only called from within
ice_common.c, so its safe to mark it static and stop declaring it in the
ice_common.h header as well.
Fixes: 8a3a565ff2 ("ice: add admin commands to access cgu configuration")
Fixes: d7999f5ea6 ("ice: implement dpll interface to control cgu")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202309191214.TaYEct4H-lkp@intel.com
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Simon Horman <horms@kernel.org> # build-tested
Link: https://lore.kernel.org/r/20231002185132.1575271-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The only feature using the Firmware (FW) shared parameters was the PTP
clock ID. Since this ID is now shared using auxiliary buss - remove the
FW shared parameters from the code.
Signed-off-by: Michal Michalik <michal.michalik@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Similar to the change made for ICE_F_SMA_CTRL, check the netlist before
enabling support for ICE_F_GNSS. This ensures that the driver only enables
the GNSS feature on devices which actually have the feature enabled in the
firmware device configuration.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add firmware admin command to access clock generation unit
configuration, it is required to enable Extended PTP and SyncE features
in the driver.
Add definitions of possible hardware variations of input and output pins
related to clock generation unit and functions to access the data.
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop @num_entries and @cd params, latter of which was always NULL.
Number of entities to alloc is passed in internal buffer, the outer layer
(that @num_entries was assigned to) meaning is closer to "the number of
requests", which was =1 in all cases.
ice_free_hw_res() was always called with 1 as its @num arg.
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Refactor __ice_aq_get_set_rss_lut() to improve reader experience and limit
misuse scenarios (undesired LUT size for given LUT type).
Allow only 3 RSS LUT type+size variants:
PF LUT sized 2048, GLOBAL LUT sized 512, and VSI LUT sized 64, which were
used on default flows prior to this commit.
Prior to the change, code was mixing the meaning of @params->lut_size and
@params->lut_type, flag assigning logic was cryptic, while long defines
made everything harder to follow.
Fix that by extracting some code out to separate helpers.
Drop some of "shift by 0" statements that originated from Intel's
internal HW documentation.
Drop some redundant VSI masks (since ice_is_vsi_valid() gives "valid" for
up to 0x300 VSIs).
After sweeping all the defines out of struct ice_aqc_get_set_rss_lut,
it fits into 7 lines.
Finally apply some cleanup to the callsite
(use of the new enums, tmp var for lengthy bit extraction).
Note that flags for 128 and 64 sized VSI LUT are the same,
and 64 is used everywhere in the code (updated to new enum here), it just
happened that there was 128 in flag name.
__ice_aq_get_set_rss_key() uses the same VSI valid bit, make constant
common for it and __ice_aq_get_set_rss_lut().
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Arpana Arland <arpanax.arland@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add defines needed for interaction with the FW admin queue interface
in relation to supporting LAG and SRIOV VFs interacting.
Add code, or make non-static previously static functions, to access
the new and changed admin queue calls for LAG.
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add the defines, fields, and detection code for FW support of LAG for
SRIOV. Also exposes some previously static functions to allow access
in the lag code.
Clean up code that is unused or not needed for LAG support. Also add
an ordered workqueue for processing LAG events.
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_alloc_lan_q_ctx function allocates the queue context array for a
given traffic class. This function uses devm_kcalloc which will
zero-allocate the structure. Thus, prior to any queue being setup by
ice_ena_vsi_txq, the q_ctx structure will have a q_handle of 0 and a q_teid
of 0. These are potentially valid values.
Modify the ice_alloc_lan_q_ctx function to initialize every member of the
q_ctx array to have invalid values. Modify ice_dis_vsi_txq to ensure that
it assigns q_teid to an invalid value when it assigns q_handle to the
invalid value as well.
This will allow other code to check whether the queue context is currently
valid before operating on it.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The current ice driver's GNSS write implementation buffers writes and
works through them asynchronously in a kthread. That's bad because:
- The GNSS write_raw operation is supposed to be synchronous[1][2].
- There is no upper bound on the number of pending writes.
Userspace can submit writes much faster than the driver can process,
consuming unlimited amounts of kernel memory.
A patch that's currently on review[3] ("[v3,net] ice: Write all GNSS
buffers instead of first one") would add one more problem:
- The possibility of waiting for a very long time to flush the write
work when doing rmmod, softlockups.
To fix these issues, simplify the implementation: Drop the buffering,
the write_work, and make the writes synchronous.
I tested this with gpsd and ubxtool.
[1] https://events19.linuxfoundation.org/wp-content/uploads/2017/12/The-GNSS-Subsystem-Johan-Hovold-Hovold-Consulting-AB.pdf
"User interface" slide.
[2] A comment in drivers/gnss/core.c:gnss_write():
/* Ignoring O_NONBLOCK, write_raw() is synchronous. */
[3] https://patchwork.ozlabs.org/project/intel-wired-lan/patch/20230217120541.16745-1-karol.kolacinski@intel.com/
Fixes: d6b98c8d24 ("ice: add write functionality for GNSS TTY")
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
10 ms is a lot of time to spend busy-waiting. Sleeping is clearly
allowed here, because we have just returned from ice_sq_send_cmd(),
which takes a mutex.
On kernels with HZ=100, this msleep may be twice as long, but I don't
think it matters.
I did not actually observe any retries happening here.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The 'buf_cpy'-related code in ice_sq_send_cmd_retry() looks broken.
'buf' is nowhere copied into 'buf_cpy'.
The reason this does not cause problems is that all commands for which
'is_cmd_for_retry' is true go with a NULL buf.
Let's remove 'buf_cpy'. Add a WARN_ON in case the assumption no longer
holds in the future.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver polls for ice_sq_done() with a 100 µs period for up to 1 s
and it uses udelay to do that.
Let's use usleep_range instead. We know sleeping is allowed here,
because we're holding a mutex (cq->sq_lock). To preserve the total
max waiting time, measure the timeout in jiffies.
ICE_CTL_Q_SQ_CMD_TIMEOUT is used also in ice_release_res(), but there
the polling period is 1 ms (i.e. 10 times longer). Since the timeout was
expressed in terms of the number of loops, the total timeout in this
function is 10 s. I do not know if this is intentional. This patch keeps
it.
The patch lowers the CPU usage of the ice-gnss-<dev_name> kernel thread
on my system from ~8 % to less than 1 %.
I received a report of high CPU usage with ptp4l where the busy-waiting
in ice_sq_send_cmd dominated the profile. This patch has been tested in
that usecase too and it made a huge improvement there.
Tested-by: Brent Rowsell <browsell@redhat.com>
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Part of code from probe can be reused in reload flow. Move this code to
separate function. Create unroll functions for each part of
initialization, like: ice_init_dev() and ice_deinit_dev(). It
simplifies unrolling and can be used in remove flow.
Avoid freeing port info as it could be reused in reload path.
Will be freed in remove path since is allocated via devm_kzalloc().
Also clean the remove path to reflect the init steps.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In DCB Willing Mode (FW managed LLDP), when the link partner changes
configuration which requires fewer TCs, the TCs that are no longer
needed are suspended by EMP FW, removed, and never resumed. This occurs
before a MIB change event is indicated to SW. The permanent suspension and
removal of these TC nodes in the scheduler prevents RDMA from being able
to destroy QPs associated with this TC, requiring a CORE reset to recover.
A new DCBX configuration change flow is defined to allow SW driver and
other SW components (RDMA) to properly adjust to the configuration
changes before they are taking effect in HW. This flow includes a
two-way handshake between EMP FW<->LAN SW<->RDMA SW.
List of changes:
- Add 'Execute Pending LLDP MIB' AQC.
- Add 'Pending Event Enable' bit.
- Add additional logic to ignore Pending Event Enable' request
while 'LLDP MIB Chnage' event is disabled.
- Add 'Execute Pending LLDP MIB' AQC sending function to FW,
which is needed to take place MIB Event change.
Signed-off-by: Tsotne Chakhvadze <tsotne.chakhvadze@intel.com>
Co-developed-by: Karen Sornek <karen.sornek@intel.com>
Signed-off-by: Karen Sornek <karen.sornek@intel.com>
Co-developed-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Co-developed-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Tested-by: Arpana Arland <arpanax.arland@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver is currently using ICE_LINK_SPEED_* defines that mirror what
ethtool.h defines, with one exception ICE_LINK_SPEED_UNKNOWN.
This issue is fixed by the following changes:
1. replace ICE_LINK_SPEED_UNKNOWN with 0 because SPEED_UNKNOWN in
ethtool.h is "-1" and that doesn't match the driver's expected behavior
2. transform ICE_LINK_SPEED_*MBPS to SPEED_* using static tables and
fls()-1 to convert from BIT() to an index in a table.
Suggested-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Co-developed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
devlink-rate API requires a priv object to be allocated when node still
doesn't have a parent. This is problematic, because ice_sched_node can't
be currently created without a parent.
Add an option to pre-allocate memory for ice_sched_node struct. Add
new arguments to ice_sched_add() and ice_sched_add_elems() that allow
for pre-allocation of memory for ice_sched_node struct.
Signed-off-by: Michal Wilczynski <michal.wilczynski@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To support new devlink-rate API ice_sched_node struct needs to store
a number of additional parameters. This includes tx_max, tx_share,
tx_weight, and tx_priority.
Add new fields to ice_sched_node struct. Add new functions to configure
the hardware with new parameters. Introduce new xarray to identify
nodes uniquely.
Signed-off-by: Michal Wilczynski <michal.wilczynski@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Several functions in ice_common.c check the firmware API version to see if
the current API version meets some minimum requirement.
Improve the readability of these checks by introducing
ice_is_fw_api_min_ver, a helper function to perform that check.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add the possibility to write to connected i2c devices using the AQ
command. FW may reject the write if the device is not on allowlist.
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add a new ice_gnss.c file for holding the basic GNSS module functions.
If the device supports GNSS module, call the new ice_gnss_init and
ice_gnss_release functions where appropriate.
Implement basic functionality for reading the data from GNSS module
using TTY device.
Add I2C read AQ command. It is now required for controlling the external
physical connectors via external I2C port expander on E810-T adapters.
Future changes will introduce write functionality.
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Sudhansu Sekhar Mishra <sudhansu.mishra@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang static analysis reports this issues
ice_common.c:5008:21: warning: The left expression of the compound
assignment is an uninitialized value. The computed value will
also be garbage
ldo->phy_type_low |= ((u64)buf << (i * 16));
~~~~~~~~~~~~~~~~~ ^
When called from ice_cfg_phy_fec() ldo is the uninitialized local
variable tlv. So initialize.
Fixes: ea78ce4dab ("ice: add link lenient and default override support")
Signed-off-by: Tom Rix <trix@redhat.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
