[Why]
DTB DTO is programmed more correctly during
link enable. Programming them on CLK update
which may arrive frequently and sporadically
per flip throws off DTB DTO.
[How]
Remove DTB DTO programming on clock update.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Chris Park <Chris.Park@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
- When transitioning FRL / DP2 is not required, we will always request
DTBCLK = 0Mhz, but PMFW returns the min freq
- This causes us to make DTBCLK requests every time we call optimize
after transitioning from FRL to non-FRL
- If DTBCLK is not required, request the min instead (then we only need
to make 1 extra request at boot time)
- Also when programming PIPE_DTO_SRC_SEL, don't programming for DP
first, just programming once for the required selection (programming
DP on an HDMI connection then switching back causes corruption)
Reviewed-by: Dillon Varone <Dillon.Varone@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Even if we block Z9 based on crossover threshold it's possible to
allow for Z8.
[How]
There's support for this on DCN314, so update the support types to
include a z8 only and z8_z10 only state.
Update the decide_zstate_support function to allow for specifying
these modes based on the Z8 threshold.
DCN31 has z-state disabled, but still update the legacy code to
map z8_only = disallow and z10_z8_only = z10_only to keep the support
the same.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Assert on non-OK response from SMU is unnecessary.
It was replaced with respective log message on other asics
in the past with commit:
"drm/amd/display: Removing assert statements for Linux"
[How]
Remove assert and add dbg logging as on other DCNs.
Signed-off-by: Roman Li <roman.li@amd.com>
Reviewed-by: Saaem Rizvi <SyedSaaem.Rizvi@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
rn_vbios_smu_set_dcn_low_power_state() produces a valid warning with
gcc-13:
drivers/gpu/drm/amd/display/dc/clk_mgr/dcn21/rn_clk_mgr_vbios_smu.c:237:6: error: conflicting types for 'rn_vbios_smu_set_dcn_low_power_state' due to enum/integer mismatch; have 'void(struct clk_mgr_internal *, enum dcn_pwr_state)'
drivers/gpu/drm/amd/display/dc/clk_mgr/dcn21/rn_clk_mgr_vbios_smu.h:36:6: note: previous declaration of 'rn_vbios_smu_set_dcn_low_power_state' with type 'void(struct clk_mgr_internal *, int)'
I.e. the type of the 2nd parameter of
rn_vbios_smu_set_dcn_low_power_state() in the declaration is int, while
the definition spells enum dcn_pwr_state. Synchronize them to the
latter (and add a forward enum declaration).
Cc: Martin Liska <mliska@suse.cz>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "Pan, Xinhui" <Xinhui.Pan@amd.com>
Cc: David Airlie <airlied@gmail.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Diagnostics reports exceptions generated when timeout waiting for
DISPCLK frequency divider change expires when testing ODM4to1.
Diagnostics reports exceptions generated when timeout waiting for OTG
busy status expires when disabling OTG during ODM4to1 test.
[How]
Increase HW status waiting time for DISPCLK frequency divider change and
OTG busy status when disable OTG.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Ariel Bernstein <Eric.Bernstein@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Vladimir Stempen <vladimir.stempen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY?]
In some cases, DCFCLK hardmin requests are not acknowledged by SMU as
the requested clock does not have a compatible ratio with current FCLK,
and it cannot be changed as FCLK P-state is not allowed.
[HOW?]
Allow FCLK p-state change prior to changing DCFCLK hardmin.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For individual feature testing, PMFW may not report all clock
values back. Driver will default them to 0 but this will
cause the BB table to be skipped and default to one state
with max clocks.
[How]
Add helper function to scan through initial clock values and
populate them with default clock limits so that BB table
can be built.
Add dpm_enabled flag to check when DPM is not enabled and
to trigger helper function.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Samson Tam <samson.tam@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The DIO FIFO will underflow if we turn off the OTG before we turn
off the FIFO.
Since this happens as part of the OTG workaround and we don't reset
the FIFO afterwards we see the error persist.
[How]
Add disable FIFO before the disable CRTC and enable FIFO after enabling
the CRTC.
Reviewed-by: Syed Hassan <Syed.Hassan@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This shouldn't trigger during tiled display hotplug/unplug but it does
because one of the tiles can end up with a NULL plane state.
This also doesn't guard against the hang that it was originally trying
to resolve, and can instead cause DIO corruption due to OTG sync
being lost.
[How]
This was reverted at one point out of DCN31 so revert it here too.
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During hot plug of specific 5K tiled display, sometimes both the tiles
are not synchronized resulting in distortion. The reason is that otgs of
both the tiles goes out of sync when otg workaround (dcnxxx_disable_otg_wa)
is applied for bandwidth optimization. The otg workaround reenables otg
but otg synchronization context is not reset and hence dc_trigger_sync()
does not resynchronize otg again.
[How]
Implement reset_sync_context_for_pipe() to reset the otg synchronization
context for the disabled pipe and its slave pipes when otg workaround is
applied.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Depending on how the clock table is constructed from PMFW we can run
into issues where we don't think we have enough bandwidth available
due to FCLK too low - eg. when the FCLK table contains invalid entries
or a single entry.
We should always pick up the maximum clocks for each state as a final
state in this case to prevent validation from failing if the table is
malformed.
We should also contain sensible defaults in the case where values
are invalid.
Redfine the clock table structures by adding a 314 prefix to make
debugging these issues easier by avoiding symbol name clashes.
Overall this policy more closely aligns to how we did things for 315,
but because of how the voltage rail is setup we should favor keeping
DCFCLK low rather than DISPCLK or DPPCLK - so use the max for those
in every entry.
Reviewed-by: Daniel Miess <daniel.miess@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need a way to retain default clock table to aid
the investigation into why 8k@30 display not
lighting up on dcn314
[How]
Use flag to prevent execution of bw_params helper
function and function for updating bw_bounding_box
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Daniel Miess <Daniel.Miess@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Since "rn_clk_mgr.h" needs ‘struct clk_mgr_internal’ which is declared
in "clk_mgr_internal.h", include "clk_mgr_internal.h" in "rn_clk_mgr.h"
instead of in its source file.
Because of the change above, change the order of '#include
"rn_clk_mgr.h"', so that the necessary structs are visible to
dcn20_clk_mgr.h.
Signed-off-by: Magali Lemes <magalilemes00@gmail.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Maíra Canal <mairacanal@riseup.net>
Reviewed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The -mno-gnu-attribute option in dcn301 clk mgr makefile hides a soft vs
hard fp error for powerpc. After removing this flag, we can see some FPU
code remains there:
gcc-11.3.0-nolibc/powerpc64-linux/bin/powerpc64-linux-ld:
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/display_mode_lib.o uses
hard float,
drivers/gpu/drm/amd/amdgpu/../display/dc/clk_mgr/dcn301/vg_clk_mgr.o
uses soft float
Therefore, remove the -mno-gnu-attribute flag for dcn301/powerpc and
move FPU-associated code to DML folder.
Signed-off-by: Melissa Wen <mwen@igalia.com>
Reviewed-by: Maíra Canal <mairacanal@riseup.net>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The -mno-gnu-attribute option in clk mgr makefile for dcn30 hides a soft
vs hard fp error for powerpc. After removing this flag, we can see some
FPU code remains there:
gcc-11.3.0-nolibc/powerpc64-linux/bin/powerpc64-linux-ld:
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/display_mode_lib.o uses
hard float,
drivers/gpu/drm/amd/amdgpu/../display/dc/clk_mgr/dcn30/dcn30_clk_mgr.o
uses soft float
Therefore, remove the -mno-gnu-attribute flag for dcn30/powerpc and move
FPU-associated code to DML folder.
Signed-off-by: Melissa Wen <mwen@igalia.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The -mno-gnu-attribute option in dcn21 clk mgr makefile hides a soft vs
hard fp error for powerpc. After removing this flag, we can see some FPU
code remains there:
/gcc-11.3.0-nolibc/powerpc64-linux/bin/powerpc64-linux-ld:
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/display_mode_lib.o uses
hard float,
drivers/gpu/drm/amd/amdgpu/../display/dc/clk_mgr/dcn21/rn_clk_mgr.o uses
soft float
Therefore, remove the -mno-gnu-attribute flag for dcn21/powerpc and move
FPU-associated code to DML folder.
Signed-off-by: Melissa Wen <mwen@igalia.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We are working to isolate FPU operations inside the DML folder, and the
file dcn32_clk_mgr has some of these operations. This commit moves the
FPU operations inside the clock manager and creates the dcn32_fpu file
to aggregate those operations. Note that there is no functional change
ere, just moving code from one part to another.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For Pixel Rate control, when on HDMI, HDMI DTO should be selected
instead of DP DTO.
[How]
Pass HDMI parameter for HDMI stream, and select correct DTO.
Signed-off-by: Chris Park <chris.park@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This commit enables the SubVP feature. To achieve that, we need to:
- Don't force p-state disallow on SubVP (can't block dummy p-state)
- Send calculated watermark to DMCUB for SubVP
- Adjust CAB mode message to PMFW
- Add a proper locking sequence for SubVP
- Various fixes to SubVP static analysis and determining SubVP config
- Currently SubVP not supported with pipe split so merge all pipes
before setting up SubVp
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Sometimes when trying to enable some feature, we have to define some
values with educated guesses, but we mark those values as TBD, which
means "To Be Determined". However, the correct way to approach it is by
loading that information from the firmware. Anyway, some of the values
that we were experimenting with caused this issue:
ERROR: modpost: "__muldf3" [drivers/gpu/drm/amd/amdgpu/amdgpu.ko] undefined!
This commit fixes this issue by removing the division by two since it is
harmless in this case.
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Fixes: 265280b998 ("drm/amd/display: add CLKMGR changes for DCN32/321")
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clang warns:
drivers/gpu/drm/amd/amdgpu/../display/dc/clk_mgr/dcn32/dcn32_clk_mgr.c:549:4: warning: misleading indentation; statement is not part of the previous 'else' [-Wmisleading-indentation]
pll_req = dc_fixpt_from_int(pll_req_reg & clk_mgr->clk_mgr_mask->FbMult_int);
^
drivers/gpu/drm/amd/amdgpu/../display/dc/clk_mgr/dcn32/dcn32_clk_mgr.c:542:3: note: previous statement is here
else
^
1 warning generated.
Indent this statement to the left, as it was clearly intended to be
called unconditionally, which will fix the warning.
Link: https://github.com/ClangBuiltLinux/linux/issues/1655
Fixes: 3e838f7ccf ("drm/amd/display: Get VCO frequency from registers")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
