[Why]
Even if we block Z9 based on crossover threshold it's possible to
allow for Z8.
[How]
There's support for this on DCN314, so update the support types to
include a z8 only and z8_z10 only state.
Update the decide_zstate_support function to allow for specifying
these modes based on the Z8 threshold.
DCN31 has z-state disabled, but still update the legacy code to
map z8_only = disallow and z10_z8_only = z10_only to keep the support
the same.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Assert on non-OK response from SMU is unnecessary.
It was replaced with respective log message on other asics
in the past with commit:
"drm/amd/display: Removing assert statements for Linux"
[How]
Remove assert and add dbg logging as on other DCNs.
Signed-off-by: Roman Li <roman.li@amd.com>
Reviewed-by: Saaem Rizvi <SyedSaaem.Rizvi@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The DIO FIFO will underflow if we turn off the OTG before we turn
off the FIFO.
Since this happens as part of the OTG workaround and we don't reset
the FIFO afterwards we see the error persist.
[How]
Add disable FIFO before the disable CRTC and enable FIFO after enabling
the CRTC.
Reviewed-by: Syed Hassan <Syed.Hassan@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This shouldn't trigger during tiled display hotplug/unplug but it does
because one of the tiles can end up with a NULL plane state.
This also doesn't guard against the hang that it was originally trying
to resolve, and can instead cause DIO corruption due to OTG sync
being lost.
[How]
This was reverted at one point out of DCN31 so revert it here too.
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During hot plug of specific 5K tiled display, sometimes both the tiles
are not synchronized resulting in distortion. The reason is that otgs of
both the tiles goes out of sync when otg workaround (dcnxxx_disable_otg_wa)
is applied for bandwidth optimization. The otg workaround reenables otg
but otg synchronization context is not reset and hence dc_trigger_sync()
does not resynchronize otg again.
[How]
Implement reset_sync_context_for_pipe() to reset the otg synchronization
context for the disabled pipe and its slave pipes when otg workaround is
applied.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Depending on how the clock table is constructed from PMFW we can run
into issues where we don't think we have enough bandwidth available
due to FCLK too low - eg. when the FCLK table contains invalid entries
or a single entry.
We should always pick up the maximum clocks for each state as a final
state in this case to prevent validation from failing if the table is
malformed.
We should also contain sensible defaults in the case where values
are invalid.
Redfine the clock table structures by adding a 314 prefix to make
debugging these issues easier by avoiding symbol name clashes.
Overall this policy more closely aligns to how we did things for 315,
but because of how the voltage rail is setup we should favor keeping
DCFCLK low rather than DISPCLK or DPPCLK - so use the max for those
in every entry.
Reviewed-by: Daniel Miess <daniel.miess@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need a way to retain default clock table to aid
the investigation into why 8k@30 display not
lighting up on dcn314
[How]
Use flag to prevent execution of bw_params helper
function and function for updating bw_bounding_box
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Daniel Miess <Daniel.Miess@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
