Starting from ICL, the default for MIPI GPIO sequences seems to be using
native GPIOs i.e. GPIOs available in the GPU. These native GPIOs reuse
many pins that quite frankly seem scary to poke based on the VBT
sequences. We pretty much have to trust that the board is configured
such that the relevant HPD, PP_CONTROL and GPIO bits aren't used for
anything else.
MIPI sequence v4 also adds a flag to fall back to non-native sequences.
v5:
- Wrap SHOTPLUG_CTL_DDI modification in spin_lock() in icp_irq_handler()
too (Ville)
- References instead of Closes issue 6131 because this does not fix everything
v4:
- Wrap SHOTPLUG_CTL_DDI modification in spin_lock_irq() (Ville)
v3:
- Fix -Wbitwise-conditional-parentheses (kernel test robot <lkp@intel.com>)
v2:
- Fix HPD pin output set (impacts GPIOs 0 and 5)
- Fix GPIO data output direction set (impacts GPIOs 4 and 9)
- Reduce register accesses to single intel_de_rwm()
References: https://gitlab.freedesktop.org/drm/intel/-/issues/6131
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221219105955.4014451-1-jani.nikula@intel.com
(cherry picked from commit f087cfe6fc)
Cc: stable@vger.kernel.org # 6.1
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
bigjoiner_pipes() doesn't consider that:
- RKL only has three pipes
- some pipes may be fused off
This means that intel_atomic_check_bigjoiner() won't reject
all configurations that would need a non-existent pipe.
Instead we just keep on rolling witout actually having
reserved the slave pipe we need.
It's possible that we don't outright explode anywhere due to
this since eg. for_each_intel_crtc_in_pipe_mask() will only
walk the crtcs we've registered even though the passed in
pipe_mask asks for more of them. But clearly the thing won't
do what is expected of it when the required pipes are not
present.
Fix the problem by consulting the device info pipe_mask already
in bigjoiner_pipes().
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221118185201.10469-1-ville.syrjala@linux.intel.com
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
(cherry picked from commit f1c87a94a1)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
GVT Changes:
- gvt-next stuff mostly with refactor for the new MDEV interface.
i915 Changes:
- PSR fixes and improvements (Jouni)
- DP DSC fixes (Vinod, Jouni)
- More general display cleanups (Jani)
- More display collor management cleanup targetting degamma (Ville)
- remove circ_buf.h includes (Jiri)
- wait power off delay at driver remove to optimize probe (Jani)
- More audio cleanup targeting the ELD precompute readout (Ville)
- Enable DC power states on all eDP ports (Imre)
- RPL-P stepping info (Matt Atwood)
- MTL enabling patches (RK)
- Removal of DG2 force_probe (Matt)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/Y3f71obyEkImXoUF@intel.com
Factor out functions to get/put the AUX_IO power domain for the main
link on DDI ports.
While at it clarify the corresponding code comment.
No functional change.
v2:
- s/(get/put)_aux_power_for_main_link/main_link_aux_power_domain_(get/put)
(Jani)
- Clarify in the code comment that AUX_IO is needed only by TypeC besides
eDP/PSR.
v3:
- Rebased on checking intel_encoder_can_psr() instead of crtc->has_psr.
v4:
- Don't call fetch_and_zero() with side-effect during variable
declaration. (Ville)
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221114122251.21327-9-imre.deak@intel.com
Starting with TGL eDP is supported on ports B+ (besides port A), so make
sure DC states are not blocked on any such ports. For this add an
AUX_IO_<port> power domain for each port with eDP support. These domains
similarly to AUX_IO_A enable only the AUX_IO_<port> power well for an
enabled port, whereas the existing AUX_<port> domains enable both the
AUX_IO_<port> and the DC_OFF power wells as required by DP AUX transfers.
v2: (Ville)
- Split the change using AUX vs. AUX_IO on port A to a separate patch.
- Select AUX_IO vs. AUX based on crtc_state->has_psr instead of
is_edp().
v3:
- Rebased on checking intel_encoder_can_psr() instead of crtc->has_psr.
v4:
- Fix warn in intel_display_power_aux_io_domain(). (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221114122251.21327-6-imre.deak@intel.com
Use the AUX_IO_A display power domain only for eDP on port A where PSR
is also supported. This is the case where DC states need to be enabled
while the output is enabled - ensured by AUX_IO_A domain not enabling
the DC_OFF power well. Otherwise port A can be treated the same way as
other ports with an external DP output: using the AUX_<port> domain
which disables the unrequired DC states.
This change prepares for the next patch enabling DC states on all ports
supporting eDP/PSR besides port A.
v2:
- Check the encoder PSR capability instead of PSR being enabled in the
crtc_state, as the latter can be changed with a fastset.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221114122251.21327-5-imre.deak@intel.com
When doing HDMI+non-HDMI cloning the other sink can't get
the infoframes/etc. so stuff like limited range output is
not a good idea.
Similarly when doing HDMI+HDMI cloning on g4x (only platform
where we allow it) only one of the ports can receive infoframes
and so again using any fancy stuff is a bad idea. We also don't
track the inforames/audio state per-port so we'd end up with
some kind of random mismash state when multipled encoders try
to compute the same stuff. And the hardware will in fact
automagically disable audio/infoframe transmission if you try
to enable it for multiple HDMI ports at the same time.
Thus disable all HDMI specific features when cloning.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221107194604.15227-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Panel power off delay is the time the panel power needs to remain off
after being switched off, before it can be switched on again.
For the purpose of respecting panel power off delay at driver probe,
assuming the panel was last switched off at driver probe is overly
pessimistic. If the panel was never on, we'd end up waiting for no
reason.
We don't know what has happened before kernel boot, but we can make some
assumptions:
- The panel may have been switched off right before kernel boot by some
pre-os environment.
- After kernel boot, the panel may only be switched off by i915.
- At i915 driver probe, only a previously loaded and removed i915 may
have switched the panel power off.
With these assumptions, we can initialize the last power off time to
kernel boot time, if we also ensure i915 driver remove waits for the
panel power off delay after switching panel power off.
This shaves off the time it takes from kernel boot to i915 probe from
the first panel enable, if (and only if) the panel was not already
enabled at boot.
The encoder destroy hook is pretty much the last place where we can
wait, right after we've ensured the panel power has been switched off,
and before the whole encoder is destroyed.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/7417
Cc: Lee Shawn C <shawn.c.lee@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Lee Shawn C <shawn.c.lee@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221116150657.1347504-1-jani.nikula@intel.com
Turns out many of the files that need i915_reg.h get it implicitly via
{display/intel_de.h, gt/intel_context.h} -> i915_trace.h -> i915_irq.h
-> i915_reg.h. Since i915_trace.h doesn't actually need i915_irq.h,
makes sense to drop it, but that requires adding quite a few new
includes all over the place.
Prefer including i915_reg.h where needed instead of adding another
implicit include, because eventually we'll want to split up i915_reg.h
and only include the specific registers at each place.
Also some places actually needed i915_irq.h too.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6e78a2e0ac1bffaf5af3b5ccc21dff05e6518cef.1668008071.git.jani.nikula@intel.com
Currently when opeating in split gamma mode we do the
"skip ever other sw LUT entry" trick in the low level
LUT programming/readout functions. That is very annoying
and a big hinderance to revamping the color management
uapi.
Let's get rid of that problem by making half sized copies
of the software LUTs and plugging those into the internal
{pre,post}_csc_lut attachment points (instead of the sticking
the uapi provide sw LUTs there directly).
With this the low level stuff will operate purely in terms
the hardware LUT sizes, and all uapi nonsense is contained
to the atomic check phase. The one thing we do lose is
intel_color_assert_luts() since we no longer have a way to
check that the uapi LUTs were correctly used when generating
the internal copies. But that seems like a price worth paying.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221026113906.10551-12-ville.syrjala@linux.intel.com
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Implement the fbdev's read/write helpers with the same functions. Use
the generic fbdev's code as template. Convert all drivers.
DRM's fb helpers must implement regular I/O functionality in struct
fb_ops and possibly perform a damage update. Handle all this in the
same functions and convert drivers. The functionality has been used
as part of the generic fbdev code for some time. The drivers don't
set struct drm_fb_helper.fb_dirty, so they will not be affected by
damage handling.
For I/O memory, fb helpers now provide drm_fb_helper_cfb_read() and
drm_fb_helper_cfb_write(). Several drivers require these. Until now
tegra used I/O read and write, although the memory buffer appears to
be in system memory. So use _sys_ helpers now.
v3:
* fix docs (Javier)
v2:
* rebase onto vmwgfx changes
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221103151446.2638-18-tzimmermann@suse.de
Driver Changes:
- Fix for #7306: [Arc A380] white flickering when using arc as a
secondary gpu (Matt A)
- Add Wa_18017747507 for DG2 (Wayne)
- Avoid spurious WARN on DG1 due to incorrect cache_dirty flag
(Niranjana, Matt A)
- Corrections to CS timestamp support for Gen5 and earlier (Ville)
- Fix a build error used with clang compiler on hwmon (GG)
- Improvements to LMEM handling with RPM (Anshuman, Matt A)
- Cleanups in dmabuf code (Mike)
- Selftest improvements (Matt A)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/Y2N11wu175p6qeEN@jlahtine-mobl.ger.corp.intel.com
