Use pm_runtime_get_if_in_use() in s_ctrl to apply controls
only when the device is powered on.
Rework the control set function to balance the
pm_runtime_get_if_in_use() call with
pm_runtime_put() at the end of the function.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rework the s_stream() operation to turn the sensor on and
off at stream enable/disable time using the pm_runtime infrastructure.
Protect the stream on/off from being called multiple times in
sequence with a 'streaming' flag.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for the V4L2_CID_HBLANK read-only control.
The implementation has been upported from RaspberryPi BSP commit:
commit d82f202156 ("media: i2c: ov5647: Set V4L2_SUBDEV_FL_HAS_EVENTS flag")
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Now that the driver supports more than a single mode, implement the
.set_fmt pad operation and adjust the existing .get_fmt one to report
the currently applied format.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The SBGGR10_1X10 formats support more resolutions than SBGGR8_1X8.
Make it the default sensor format and set 2x2 binned 640x480 resolution
as default sensor size as it maximizes the FOV and framerate.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Before adding new modes, rename the only existing one to report
the bit depth to distinguish it from future additions.
While at it, briefly describe the mode.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Support the get_selection() pad operation to report the device
full pixel array size, the currently applied analogue crop rectangle and
the active pixel array dimensions.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Break format handling out from the main driver structure.
This commit prepares for the introduction of more sensor formats and
resolutions by instrumenting the existing operation to work on multiple
modes instead of assuming a single supported one.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The driver structure name is referred to with different names ('ov5647',
'state', 'sensor') in different functions in the driver.
Polish this up by using 'struct ov5647 *sensor' everywhere.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the driver mutex to protect s_stream() operations.
This will become more relevant once the sensor will support more formats
and set_format() could be issue concurrently to s_stream().
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Implement the .enum_frame_size subdev pad operation.
As the driver only supports one format and one resolution at the moment
the implementation is trivial.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rename __sensor_init() function to ov5647_set_mode() as the function
is a regular one and the double underscores prefix shall be removed, and
then move it to program the mode at s_stream(1) time, not at sensor power
up.
Break out from __sensor_init() the stream_off() operation call at sensor
power up to coax the lanes in LP-11 state.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The ov5647_read()/ov5647_write() return in case of success the number
of bytes read or written respectively. This requires callers to check
if the return value is less than zero to detect an error. Unfortunately,
in several places, callers directly return the result of a read/write
call, causing issues when the returned valued is checked to be different
from zero to detect an error.
Fix this by returning zero if i2c_master_send() and i2c_master_read()
return a positive value (the number of bytes written or read).
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The driver has some obvious style issues which are worth fixing before
expanding the driver capabilities.
Fix:
- Variable declaration order
- Function parameters alignment
- Multi-line comments and spurious line breaks
- Use lowercase for hexadecimal values
- > 80 cols lines
Cosmetic change, no functional changes intended.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix obtaining CCS static data version minor part correctly. Instead, the
upper 8 bits were obtained from the major version number.
Fixes: a6b396f410 ("media: ccs: Add CCS static data parser library")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The highest fundamental frequency signal for C-PHY is half of the symbol
rate which is similar to D-PHY. Take this into account in ccs-pll.
Also remove the outdated comment.
Fixes: 8030aa4f9c ("media: ccs-pll: Add C-PHY support")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Try parsing the firmware also as C-PHY. Do this only after D-PHY as older
firmware may not explicitly specify bus-type in which case D-PHY is the
default.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Print pixel rates on CSI-2 bus as well as in pixel array as the variation
allowed in PLL capabilities makes this non-trivial to figure out
otherwise.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Support dual data rate operational system and pixel clocks by conveying
the flags to the PLL calculator and updating how the link rate is
calculated.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for dual data rate operational system and pixel clocks. This
is implemented using two PLL flags.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for sensors that either require dual PLL or support single or
dual PLL but use dual PLL as default.
Use sensor default configuration for sensors that support both modes.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for sensors that have separate VT and OP domain PLLs.
This support is trivial in the sense that it aims for the same VT pixel
rate than that on the CSI-2 bus. The vast majority of sensors is better
supported by higher frequencies in VT domain in binned and possibly scaled
configurations.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Separate VT divisor limit calculation from the rest of the VT PLL branch
calculation. This way it can be used for dual PLL support as well.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The PLL calculator only searched even total divisor values apart from one,
but this is wrong: the total divisor is odd in cases where system divisor
is one. Fix this by including odd total PLL values where system divisor is
one to the search.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Refactor bounds checks so that the caller can decide what to check. This
allows doing the checks early, when the values are available.
This also adds front OP PLL configuration and limits.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Print information on PLL tree configuration based on the flags. This also
adds support for printing dual PLL trees, and better separates between OP
and VT PLL trees.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Some sensors support derating (VT domain speed faster than OP) or
overrating (VT domain speed slower than OP). While this was supported for
the driver, the hardware support for the feature was never verified. Do
that now, and for those devices without that support, VT and OP speeds
have to match.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Split off the VT sub clock tree calculation from the rest, into its own
function. Also call the op_pll_fr argument pll_fr, since soon these may
not be OP tree values.
This paves way for additional features in the future such as dual PLL
support.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Flexible OP PLL pixel clock divider allows a higher OP pixel clock than
what the bus can transfer. This generally makes it easier to select pixel
clock dividers.
This changes how the pixel rate on the bus and minimum VT divisor are
calculated, as the pixel rate is no longer directly determined by the
OP pixel clock and the number of the lanes.
Also add a sanity check for sensors that do not support flexible OP PLL
pixel clock divider. This could have caused the PLL calculator to come up
with an invalid configuration for those devices.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The l parameter defines the number of clock cycles to process a single
pixel per OP lane. It is calculated based on a new register
op_bits_per_lane.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
CCS allows odd PLL dividers other than 1, granted that the corresponding
capability bit is set. Support this both in the PLL calculator and the CCS
driver.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
