Pull spi updates from Mark Brown:
"A busy enough release, but not for the core which has only seen very
small updates. The biggest addition is the readdition of support for
detailed configuration of the timings around chip selects. That had
been removed for lack of use but there's been applications found for
it on Atmel systems. Otherwise the updates are mostly feature
additions and cleanups to existing drivers.
Summary:
- Provide a helper for getting device match data in a way that
abstracts away which firmware interface is being used.
- Re-add the spi_set_cs_timing() API for detailed configuration of
the timing around chip select and support it on Atmel.
- Support for MediaTek MT7986, Microchip PCI1xxxx, Nuvoton WPCM450
FIU and Socionext F_OSPI"
* tag 'spi-v6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (66 commits)
spi: dt-bindings: Convert Synquacer SPI to DT schema
spi: spi-gpio: Don't set MOSI as an input if not 3WIRE mode
spi: spi-mtk-nor: Add recovery mechanism for dma read timeout
spi: spi-fsl-lpspi: add num-cs binding for lpspi
spi: spi-fsl-lpspi: support multiple cs for lpspi
spi: mtk-snfi: Add snfi support for MT7986 IC
spi: spidev: mask SPI_CS_HIGH in SPI_IOC_RD_MODE
spi: cadence-quadspi: Add minimum operable clock rate warning to baudrate divisor calculation
spi: microchip: pci1xxxx: Add suspend and resume support for PCI1XXXX SPI driver
spi: dt-bindings: nuvoton,wpcm450-fiu: Fix warning in example (missing reg property)
spi: dt-bindings: nuvoton,wpcm450-fiu: Fix error in example (bogus include)
spi: mediatek: Enable irq when pdata is ready
spi: spi-mtk-nor: Unify write buffer on/off
spi: intel: Add support for SFDP opcode
spi: intel: Take possible chip address into account in intel_spi_read/write_reg()
spi: intel: Implement adjust_op_size()
spi: intel: Use ->replacement_op in intel_spi_hw_cycle()
spi: cadence: Drop obsolete dependency on COMPILE_TEST
spi: Add Nuvoton WPCM450 Flash Interface Unit (FIU) bindings
spi: wpcm-fiu: Add direct map support
...
Between SPI transactions, all SPI pins are in HiZ state. When using the SS
signal from the SPICC controller it's not an issue because when the
transaction resumes all pins come back to the right state at the same time
as SS.
The problem is when we use CS as a GPIO. In fact, between the GPIO CS
state change and SPI pins state change from idle, you can have a missing or
spurious clock transition.
Set a bias on the clock depending on the clock polarity requested before CS
goes active, by passing a special "idle-low" and "idle-high" pinctrl state
and setting the right state at a start of a message
Reported-by: Da Xue <da@libre.computer>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
Link: https://lore.kernel.org/r/20221004-up-aml-fix-spi-v4-2-0342d8e10c49@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Since [1], controller's busy flag isn't set anymore when the
__spi_transfer_message_noqueue() is used instead of the
__spi_pump_transfer_message() logic for spi_sync transfers.
Since the pow2 clock ops were limited to only be available when a
transfer is ongoing (between prepare_transfer_hardware and
unprepare_transfer_hardware callbacks), the only way to track this
down is to check for the controller cur_msg.
[1] ae7d2346dc ("spi: Don't use the message queue if possible in spi_sync")
Fixes: 09992025da ("spi: meson-spicc: add local pow2 clock ops to preserve rate between messages")
Fixes: ae7d2346dc ("spi: Don't use the message queue if possible in spi_sync")
Reported-by: Markus Schneider-Pargmann <msp@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/r/20220908121803.919943-1-narmstrong@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
At the end of a message, the HW gets a reset in meson_spicc_unprepare_transfer(),
this resets the SPICC_CONREG register and notably the value set by the
Common Clock Framework.
This is problematic because:
- the register value CCF can be different from the corresponding CCF cached rate
- CCF is allowed to change the clock rate whenever the HW state
This introduces:
- local pow2 clock ops checking the HW state before allowing a clock operation
- separation of legacy pow2 clock patch and new enhanced clock path
- SPICC_CONREG datarate value is now value kepts across messages
It has been checked that:
- SPICC_CONREG datarate value is kept across messages
- CCF is only allowed to change the SPICC_CONREG datarate value when busy
- SPICC_CONREG datarate value is correct for each transfer
This didn't appear before commit 3e0cf4d3fc ("spi: meson-spicc: add a linear clock divider support")
because we recalculated and wrote the rate for each xfer.
Fixes: 3e0cf4d3fc ("spi: meson-spicc: add a linear clock divider support")
Reported-by: Da Xue <da@libre.computer>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220811134445.678446-1-narmstrong@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This check misses checking for platform_get_irq()'s call and may passes
the negative error codes to devm_request_irq(), which takes unsigned IRQ #,
causing it to fail with -EINVAL, overriding an original error code.
Stop calling devm_request_irq() with invalid IRQ #s.
Fixes: 454fa271bc ("spi: Add Meson SPICC driver")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220126110447.24549-1-linmq006@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If devm_spi_register_master() fails in meson_spicc_probe(),
spicc->core is left undisabled. The patch fixes that.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add new compatible string to support SPICC controller which
found at Amlogic Meson-AXG SoC. This is aiming at adding
a couple of enhanced feature patches.
Signed-off-by: Sunny Luo <sunny.luo@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPICC hardware block on the Amlogic SoCs is Communication oriented and
can do Full-Duplex 8- to 32-bit width SPI transfers up to 30MHz.
The current driver only supportd the PIO transfer mode since the DMA seems
broken on available hardware.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
