commit 9f050c7f97 upstream.
Print the supported functions mask in addition to
the version. This is useful in debugging PX
problems since we can see what functions are available.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f53492f86 upstream.
The CP semaphore queue on CIK has a bug that triggers if uncompleted
waits use the same address while a signal is still pending. Work around
this by using different addresses for each sync.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d2cb9a54a upstream.
Each invocation of va_copy() must be matched by a corresponding
invocation of va_end() in the same function.
This regression has been introduced in
commit e29bb4ebbf
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Fri Sep 20 10:20:59 2013 +0100
drm/i915: Use a temporary va_list for two-pass string handling
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2cac613be8 upstream.
Atm we setup the HW panel power sequencer logic both for eDP and DP
ports. On eDP we then go on and start the power on sequence and commence
with link training when it's ready. On DP we don't do the power on
sequencing but do the link training immediately. At this point the DP
PHY block gets stuck, since - supposedly - it is waiting for the power
on sequence to finish. The actual register write that seems to hold off
the PHY is PIPEX_PP_ON_DELAYS[Panel Control Port Select]. Writing here
a non-0 value eventually sets PIPEX_PP_STATUS[Require Asset Status] to
1 and blocks the PHY until the panel power on is ready.
Fix this by not doing any PP sequencing setup for DP ports.
Thanks to Ville Syrjälä, Jesse Barnes and Todd Previte for the help in
tracking this down.
Note that on older gmch platforms (where we have lvds instead of edp)
we've hacked around this by writing the magic ABCD unlock key to PP
registers, which disables the hw sanity checks.
For edp all platforms thus far had the pch split, with the edp port in
the north display complex and the PP registers on the pch the hw
sanity checks (expressed through the "Require Asset Status" bit) was
never functional, hence never a real issue.
This regression has been introduce in
commit bf13e81b90
Author: Jani Nikula <jani.nikula@intel.com>
Date: Fri Sep 6 07:40:05 2013 +0300
drm/i915: add support for per-pipe power sequencing on vlv
Signed-off-by: Imre Deak <imre.deak@intel.com>
[danvet: Add note about the bigger story here.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 53dac83053 upstream.
In some cases we enter the cursor code with file_priv = NULL causing an oops,
we also can try to unpin something that isn't pinned, and this is a good fix for it.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0d00c488f3 upstream.
With dma compliance / IOMMU support added to the driver in kernel 3.13,
the dma addresses can exceed 44 bits, which is what we support in
32-bit mode and with GMR1.
So in 32-bit mode and optionally in 64-bit mode, restrict the dma
addresses to 44 bits, and strip the old GMR1 code.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f4b4718b61 upstream.
these 3 were checking in_interrupt but we have situations where
calling vunmap under this could cause a BUG to be hit in
smp_call_function_many. Use the drm_can_sleep macro instead,
which should stop this path from been taken in this case.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eb86301f29 upstream.
When setting a new frame buffer with the mode set base operation the
pitch value might change. Set the hardware plane pitch register at the
same time as the plane base address in the rcar_du_plane_update_base()
function to make sure the pitch value always matches the frame buffer.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ab11a2635 upstream.
At least drm/i915 expects that the obj->dev pointer is set even in
failure paths. Specifically when the shmem initialization fails we
call i915_gem_object_free which needs to deref obj->base.dev to get at
the slab pointer in the device private structure. And the shmem
allocation can easily fail when userspace is hitting open file limits.
Doing the structure init even when the shmem file allocation fails
prevents this Oops.
This is a regression from
commit 89c8233f82
Author: David Herrmann <dh.herrmann@gmail.com>
Date: Thu Jul 11 11:56:32 2013 +0200
drm/gem: simplify object initialization
v2: Add regression note which Chris supplied.
Testcase: igt/gem_fd_exhaustion
Reported-and-Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
References: http://lists.freedesktop.org/archives/intel-gfx/2014-January/038433.html
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Cc: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 372fbb8e39 upstream.
Currently we report through our error state only the rings that have
been initialised (as detected by ring->obj). This check is done after
the GPU reset and ring re-initialisation, which means that the software
state may not be the same as when we captured the hardware error and we
may not print out any of the vital information for debugging the hang.
This (and the implied object leak) is a regression from
commit 3d57e5bd12
Author: Ben Widawsky <ben@bwidawsk.net>
Date: Mon Oct 14 10:01:36 2013 -0700
drm/i915: Do a fuller init after reset
Note that we are already starting to get bug reports with incomplete
error states from 3.13, which also hampers debugging userspace driver
issues.
v2: Prevent a NULL dereference on 830gm/845g after a GPU reset where
the scratch obj may be NULL.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=74094
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Add a bit of fluff to make it clear we need this expedited in
stable.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 22accca017 upstream.
Not removing pm qos request and free memory for it can cause crash,
when some other driver use pm qos. For example, this oops:
BUG: unable to handle kernel paging request at fffffffffffffff8
IP: [<ffffffff81307a6b>] plist_add+0x5b/0xd0
Call Trace:
[<ffffffff810acf25>] pm_qos_update_target+0x125/0x1e0
[<ffffffff810ad071>] pm_qos_add_request+0x91/0x100
[<ffffffffa053ec14>] e1000_open+0xe4/0x5b0 [e1000e]
was caused by earlier i915 probe failure:
[drm:i915_report_and_clear_eir] *ERROR* EIR stuck: 0x00000010, masking
[drm:init_ring_common] *ERROR* render ring initialization failed ctl 0001f001 head 00003004 tail 00000000 start 00003000
[drm:i915_driver_load] *ERROR* failed to init modeset
i915: probe of 0000:00:02.0 failed with error -5
Bug report:
http://bugzilla.redhat.com/show_bug.cgi?id=1057533
Reported-by: Giandomenico De Tullio <ghisha@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
[danvet: Drop unnecessary code movement.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 232a6ee9af upstream.
Add new definitions for hotplug live status bits for VLV2 since they're
in reverse order from the gen4x ones.
Changelog:
- Restored gen4 bit definitions
- Added new definitions for VLV2
- Added platform check for IS_VALLEYVIEW() in dp_detect to use the correct
bit defintions
- Replaced a lost trailing brace for the added switch()
Signed-off-by: Todd Previte <tprevite@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=73951
[danvet: Switch to _VLV postfix instead of prefix and regroupg
comments again so that the g4x warning is right next to those defines.
Also add a _G4X suffix for those special ones. Also cc stable.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ec14ba4779 upstream.
The 'offset' field of the 'scatterlist' structure was wrongly
programmed with the offset value from the base of stolen area,
whereas this field indicates the offset from where the interested
data starts within the first PAGE pointed to by 'scattterlist'
structure. As a result when a new GEM object allocated from stolen
area is mapped to GTT, it could lead to an overwrite of GTT entries
as the page count calculation will go wrong, refer the function
'sg_page_count'.
v2: Modified the commit message. (Chris)
Signed-off-by: Akash Goel <akash.goel@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=71908
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=69104
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 304d695c3d upstream.
In very rare cases (such as a memory failure stress test) it is possible
to fill the entire ring without emitting a request. Under this
circumstance, the outstanding request is flushed and waited upon. After
space on the ring is cleared, we return to emitting the new command -
except that we just cleared the seqno allocated for this operation and
trigger the sanity check that a request is only ever emitted with a
valid seqno. The fix is to rearrange the code to make sure the
allocation of the seqno for this operation is after any required flushes
of outstanding operations.
The bug exists since the preallocation was introduced in
commit 9d7730914f
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Tue Nov 27 16:22:52 2012 +0000
drm/i915: Preallocate next seqno before touching the ring
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 90d6db1635 upstream.
Some firmware images may be large (64K), so using kmalloc memory is
inappropriate for them. Use vmalloc instead, to avoid high-order
allocation failures.
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 78fe9e545c upstream.
Some DCE8 boards have a funky BlankCrtc table that results
in a timeout when trying to blank the display. The
timeout is harmless (all operations needed from the table
are complete), but wastes time and is confusing to users so
work around it.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=73420
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9a321c6b2 upstream.
DCE5 and newer hardware only has 1 DAC. Use the correct
offset. This may fix display problems on certain board
configurations.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 10e9ffae46 upstream.
We need to set the engine bit to select the ME and
also set the full cache bit. Should help stability
on TN and cayman.
V2: fix up surface sync in ib execute as well
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
