There could be multiple qgv and psf gv points with similar values.
Apparently pcode's handling of psf and qgv points are different. For
qgv case, pcode sets whatever is asked by the driver. But in case
of psf gv points, it compares the bw from points before setting the
mask. This can cause problems in scenarios where we have to disable
sagv by setting the highest bw point and there could be multiple
points with highest bw. So to set the maximum psf gv point, find
out all the points with the highest bw and set all together.
v1: - use the same treatment to qgv points as well (Vinod)
v2: - pcode confirms that for qgv points, it sets whatever the
driver sets (Vinod)
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240405113533.338553-6-vinod.govindapillai@intel.com
Problem is that on some platforms, we do get QGV point mask in wrong
state on boot. However driver assumes it is set to 0
(i.e all points allowed), however in reality we might get them all
restricted, causing issues.
Lets disable SAGV initially to force proper QGV point state.
If more QGV points are available, driver will recalculate and update
those then after next commit.
v2: - Added trace to see which QGV/PSF GV point is used when SAGV is
disabled.
v3: - Move force disable function to intel_bw_init in order to initialize
bw state as well, so that hw/sw are immediately in sync after init.
v4: - Don't try sending PCode request, seems like it is not possible at
intel_bw_init, however assigning bw->state to be restricted as if
SAGV is off, still forces driveer to send PCode request anyway on
next modeset, so the solution still works.
However we still need to address the case, when no display is
connected, which anyway requires much more changes.
v5: - Put PCode request back and apply temporary hack to make the
request succeed(in case if there 2 PSF GV points with same BW, PCode
accepts only if both points are restricted/unrestricted same time)
- Fix argument sequence for adl_qgv_bw(Ville Syrjälä)
v6: - Fix wrong platform checks, not to break everything else.
v7: - Split the handling of quplicate QGV/PSF GV points (Vinod)
Restrict force disable to display version below 14 (Vinod)
v8: - Simplify icl_force_disable_sagv (Vinod)
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240405113533.338553-5-vinod.govindapillai@intel.com
We need that in order to force disable SAGV in next patch.
Also it is beneficial to separate that code, as in majority cases,
when SAGV is enabled, we don't even need those calculations.
Also we probably need to determine max PSF GV point as well, however
currently we don't do that when we disable SAGV, which might be
actually causing some issues in that case.
v2: - Introduce helper adl_qgv_bw(counterpart to adl_psf_bw)
(Ville Syrjälä)
- Don't restrict psf gv points for SAGV disable case
(Ville Syrjälä)
v3: - Update icl_max_bw_qgv_point_mask to return max qgv point
mask (Vinod)
v4: - Minor changes in icl_find_qgv_points (Vinod)
v5: - use max_bw_point instead of max_bw_point_mask (stan)
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240405113533.338553-3-vinod.govindapillai@intel.com
For debug purposes we need those - error path won't flood the log,
however there has been already numerous cases, when due to lack
of debugs, we couldn't immediately tell what was the problem on
customer machine, which slowed down the investigation, requiring
to get access to target device and adding those traces manually.
v2: - Make the debug more generic and move it to intel_dram_detect
(Gustavo Sousa)
v3: - Use %u for unsigned variable in debug prints (Gustavo)
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240405113533.338553-2-vinod.govindapillai@intel.com
Use the >= and < operators for the DISPLAY_VER checks everywhere.
This is what most of the code does, but especially recently random
pieces of code have started doing this differently for no good reason.
Conversion done with the following cocci:
@find@
expression i915;
constant ver;
@@
(
DISPLAY_VER(i915) <= ver
|
DISPLAY_VER(i915) > ver
)
@script:python inc@
old_ver << find.ver;
new_ver;
@@
coccinelle.new_ver = str(int(old_ver) + 1)
@@
expression find.i915;
constant find.ver;
identifier inc.new_ver;
@@
(
- DISPLAY_VER(i915) <= ver
+ DISPLAY_VER(i915) < new_ver
|
- DISPLAY_VER(i915) > ver
+ DISPLAY_VER(i915) >= new_ver
)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231127145028.4899-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
From Meteorlake, Latency Level, SAGV bloack time are read from
LATENCY_SAGV register instead of the GT driver pcode mailbox. DDR type
and QGV information are also to be read from Mem SS registers.
v2:
- Simplify MTL_MEM_SS_INFO_QGV_POINT macro(MattR)
- Nit: Rearrange the bit def's from higher to lower(MattR)
- Restore platform definition for ADL-P(MattR)
- Move back intel_qgv_point def to intel_bw.c(Jani)
v3:
- Rebase
Bspec: 64636, 64608
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Original Author: Caz Yokoyama
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220902060342.151824-9-radhakrishna.sripada@intel.com
Each gt contains an independent instance of pcode. Extend pcode functions
to interface with pcode on different gt's. To avoid creating dependency of
display functionality on intel_gt, pcode function interfaces are exposed in
terms of uncore rather than intel_gt. Callers have been converted to pass
in the appropritate (i915 or intel_gt) uncore to the pcode functions.
v2: Expose pcode functions in terms of uncore rather than gt (Jani/Rodrigo)
v3: Retain previous function names to eliminate needless #defines (Rodrigo)
v4: Move out i915_pcode_init() to a separate patch (Tvrtko)
Remove duplicated drm_err/drm_dbg from intel_pcode_init() (Tvrtko)
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220519085732.1276255-2-tvrtko.ursulin@linux.intel.com
[tursulin: fixup merge conflict]
Make the dbuf bandwidth min cdclk calculations match the spec
more closely. Supposedly the arbiter can only guarantee an equal
share of the total bandwidth of the slice to each active plane
on that slice. So we take the max bandwidth of any of the planes
on each slice and multiply that by the number of active planes
on the slice to get a worst case estimate on how much bandwidth
we require.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220303191207.27931-9-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Let's store the plane allocation in a manner which more closely
matches how the hw operates. That is, we store the packed/CbCr
ddb in one struct, and the Y ddb in another. Currently we're
storing packed/Y in one struct, CbCr in the other.
This also works pretty well for icl+ where the UV plane is
the main plane and the Y plane is subservient to it. Although
in this case we do not even use ddb_y as we do the ddb allocation
in terms of hw planes.
v2: Rebase
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220303191207.27931-2-ville.syrjala@linux.intel.com
If the only thing that is changing is SAGV vs. no SAGV but
the number of active planes and the total data rates end up
unchanged we currently bail out of intel_bw_atomic_check()
early and forget to actually compute the new WGV point
mask and thus won't actually enable/disable SAGV as requested.
This ends up poorly if we end up running with SAGV enabled
when we shouldn't. Usually ends up in underruns.
To fix this let's go through the QGV point mask computation
if either the data rates/number of planes, or the state
of SAGV is changing.
v2: Check more carefully if things are changing to avoid
the extra calculations/debugs from introducing unwanted
overhead
Cc: stable@vger.kernel.org
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> #v1
Fixes: 20f505f225 ("drm/i915: Restrict qgv points which don't have enough bandwidth.")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220218064039.12834-3-ville.syrjala@linux.intel.com
Registers that exist within the MCH BAR and are mirrored into the GPU's
MMIO space are a good candidate to separate out into their own header.
For reference, the mirror of the MCH BAR starts at the following
locations in the graphics MMIO space (the end of the MCHBAR range
differs slightly on each platform):
* Pre-gen6: 0x10000
* Gen6-Gen11 + RKL: 0x140000
v2:
- Create separate patch to swtich a few register definitions to be
relative to the MCHBAR mirror base.
- Drop upper bound of MCHBAR mirror from commit message; there are too
many different combinations between various platforms to list out,
and the documentation is spotty for the older pre-gen6 platforms
anyway.
Bspec: 134, 51771
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220215061342.2055952-2-matthew.d.roper@intel.com
Several of our i915 header files, have been including i915_reg.h. This
means that any change to i915_reg.h will trigger a full rebuild of
pretty much every file of the driver, even those that don't have any
kind of register access. Let's delete the i915_reg.h include from all
headers and add an explicit include from the .c files that truly
need the register definitions; those that need a definition of
i915_reg_t for a function definition can get it from i915_reg_defs.h
instead.
We also remove two non-register #define's (VLV_DISPLAY_BASE and
GEN12_SFC_DONE_MAX) into i915_reg_defs.h to allow us to drop the
i915_reg.h include from a couple of headers.
There's probably a lot more header dependency optimization possible, but
the changes here roughly cut the number of files compiled after 'touch
i915_reg.h' in half --- a good first step.
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220127234334.4016964-7-matthew.d.roper@intel.com
Catch-up with 5.17-rc2 and trying to align with drm-intel-gt-next
for a possible topic branch for merging the split of i915_regs...
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
With both integrated and discrete Intel GPUs in a system, the current
global check of intel_iommu_gfx_mapped, as done from intel_vtd_active()
may not be completely accurate.
In this patch we add i915 parameter to intel_vtd_active() in order to
prepare it for multiple GPUs and we also change the check away from Intel
specific intel_iommu_gfx_mapped (global exported by the Intel IOMMU
driver) to probing the presence of IOMMU on a specific device using
device_iommu_mapped().
This will return true both for IOMMU pass-through and address translation
modes which matches the current behaviour. If in the future we wanted to
distinguish between these two modes we could either use
iommu_get_domain_for_dev() and check for __IOMMU_DOMAIN_PAGING bit
indicating address translation, or ask for a new API to be exported from
the IOMMU core code.
v2:
* Check for dmar translation specifically, not just iommu domain. (Baolu)
v3:
* Go back to plain "any domain" check for now, rewrite commit message.
v4:
* Use device_iommu_mapped. (Robin, Baolu)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211126141424.493753-1-tvrtko.ursulin@linux.intel.com
The formulae has been updated to include more variables. Make
sure the code carries the same.
Bspec: 64631, 54023
v2: Make GEN11 follow the default route and fix calculation of
maxdebw(RK)
v3: Fix div by zero on default case
Correct indent for fallthrough(Jani)
v4: Fix div by zero on gen11.
v5: Fix 0 max_numchannels case
v6:
- Split gen11/gen12 algorithms
- Fix RKL deburst value
- Fix difference b/ween ICL and TGL algorithms
- Protect deinterleave from being 0
- Warn when numchannels exceeds max_numchannels
- Fix scaling of clk_max from different units
- s/deinterleave/channelwidth/ in calculating peakbw
- Fix off by one for num_planes TGL+
- Fix SAGV check
v7: Fix div by zero error on gen11
v8: Even though the algorithm for gen11 says that we need to return
derated bw for a qgv point whose planes are less than no of active
planes, we return 0 for deratedbw when only one plane is allowed.
We modify the algorithm to accommodate the case where no of active
planes are same as the min no of planes supported by a qgv point.
v9: Fix dclk scaling for dg1
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211015210041.16858-1-radhakrishna.sripada@intel.com
PSF GV points are an additional factor that can limit the
bandwidth available to display, separate from the traditional
QGV points. Whereas traditional QGV points represent possible
memory clock frequencies, PSF GV points reflect possible
frequencies of the memory fabric.
Switching between PSF GV points has the advantage of incurring
almost no memory access block time and thus does not need to be
accounted for in watermark calculations.
This patch adds support for those on top of regular QGV points.
Those are supposed to be used simultaneously, i.e we are always
at some QGV and some PSF GV point, based on the current video
mode requirements.
Bspec: 64631, 53998
v2: Seems that initial assumption made during ml conversation
was wrong, PCode rejects any masks containing points beyond
the ones returned, so even though BSpec says we have around
8 points theoretically, we can mask/unmask only those which
are returned, trying to manipulate those beyond causes a
failure from PCode. So switched back to generating mask
from 1 - num_qgv_points, where num_qgv_points is the actual
amount of points, advertised by PCode.
v3: - Extended restricted qgv point mask to 0xf, as we have now
3:2 bits for PSF GV points(Matt Roper)
- Replaced val2 with NULL from PCode request, since its not being
used(Matt Roper)
- Replaced %d to 0x%x for better readability(thanks for spotting)
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210531064845.4389-2-stanislav.lisovskiy@intel.com
