Pull drm updates from Dave Airlie:
"This is the main pull request for the drm subsystems for 6.10.
In drivers the main thing is a new driver for ARM Mali firmware based
GPUs, otherwise there are a lot of changes to amdgpu/xe/i915/msm and
scattered changes to everything else.
In the core a bunch of headers and Kconfig was refactored, along with
the addition of a new panic handler which is meant to provide a user
friendly message when a panic happens and graphical display is
enabled.
New drivers:
- panthor: ARM Mali/Immortalis CSF-based GPU driver
Core:
- add a CONFIG_DRM_WERROR option
- make more headers self-contained
- grab resv lock in pin/unpin
- fix vmap resv locking
- EDID/eDP panel matching
- Kconfig cleanups
- DT sound bindings
- Add SIZE_HINTS property for cursor planes
- Add struct drm_edid_product_id and helpers.
- Use drm device based logging in more drm functions.
- drop seq_file.h from a bunch of places
- use drm_edid driver conversions
dp:
- DP Tunnel documentation
- MST read sideband cap
- Adaptive sync SDP prep work
ttm:
- improve placement for TTM BOs in idle/busy handling
panic:
- Fixes for drm-panic, and option to test it.
- Add drm panic to simpledrm, mgag200, imx, ast
bridge:
- improve init ordering
- adv7511: allow GPIO pin sharing
- tc358775: add tc358675 support
panel:
- AUO B120XAN01.0
- Samsung s6e3fa7
- BOE NT116WHM-N44
- CMN N116BCA-EA1,
- CrystalClear CMT430B19N00
- Startek KD050HDFIA020-C020A
- powertip PH128800T006-ZHC01
- Innolux G121X1-L03
- LG sw43408
- Khadas TS050 V2
- EDO RM69380 OLED
- CSOT MNB601LS1-1
amdgpu:
- HDCP/ODM/RAS fixes
- Devcoredump improvements
- Expose VCN activity via sysfs
- SMY 13.0.x updates
- Enable fast updates on DCN 3.1.4
- Add dclk and vclk reporting on additional devices
- Add ACA RAS infrastructure
- Implement TLB flush fence
- EEPROM handling fixes
- SMUIO 14.0.2 support
- SMU 14.0.1 Updates
- SMU 14.0.2 support
- Sync page table freeing with TLB flushes
- DML2 refactor
- DC debug improvements
- DCN 3.5.x Updates
- GPU reset fixes
- HDP fix for second GFX pipe on GC 10.x
- Enable secondary GFX pipe on GC 10.3
- Refactor and clean up BACO/BOCO/BAMACO handling
- Remove invalid TTM resource start check
- UAF fix in VA IOCTL
- GPUVM page fault redirection to secondary IH rings for IH 6.x
- Initial support for mapping kernel queues via MES
- Fix VRAM memory accounting
amdkfd:
- MQD handling cleanup
- Preemption handling fixes for XCDs
- TLB flush fix for GC 9.4.2
- Properly clean up workqueue during module unload
- Fix memory leak process create failure
- Range check CP bad op exception targets to avoid reporting invalid exceptions to userspace
- Fix eviction fence handling
- Fix leak in GPU memory allocation failure case
- DMABuf import handling fix
- Enable SQ watchpoint for gfx10
i915:
- Adding new DG2 PCI ID
- add context hints for GT frequency
- enable only one CCS for compute workloads
- new workarounds
- Fix UAF on destroy against retire race and remove two earlier partial fixes
- Limit the reserved VM space to only the platforms that need it
- Fix gt reset with GuC submission is disable
- Add and use gt_to_guc() wrapper
i915/xe display:
- Lunar Lake display enabling, including cdclk and other refactors
- BIOS/VBT/opregion related refactor
- Digital port related refactor/clean-up
- Fix 2s boot time regression on DP panel replay init
- Remove duplication on audio enable/disable on SDVO and g4x+ DP
- Disable AuxCCS framebuffers if built for Xe
- Make crtc disable more atomic
- Increase DP idle pattern wait timeout to 2ms
- Start using container_of_const() for some extra const safety
- Fix Jasper Lake boot freeze
- Enable MST mode for 128b/132b single-stream sideband
- Enable Adaptive Sync SDP Support for DP
- Fix MTL supported DP rates - removal of UHBR13.5
- PLL refactoring
- Limit eDP MSO pipe only for display version 20
- More display refactor towards independence from i915 dev_priv
- Convert i915/xe fbdev to DRM client
- More initial work to make display code more independent from i915
xe:
- improved error capture
- clean up some uAPI leftovers
- devcoredump update
- Add BMG mocs table
- Handle GSCCS ER interrupt
- Implement xe2- and GuC workarounds
- struct xe_device cleanup
- Hwmon updates
- Add LRC parsing for more GPU instruction
- Increase VM_BIND number of per-ioctl Ops
- drm/xe: Add XE_BO_GGTT_INVALIDATE flag
- Initial development for SR-IOV support
- Add new PCI IDs to DG2 platform
- Move userptr over to start using hmm_range_fault
msm:
- Switched to generating register header files during build process
instead of shipping pre-generated headers
- Merged DPU and MDP4 format databases.
- DP:
- Stop using compat string to distinguish DP and eDP cases
- Added support for X Elite platform (X1E80100)
- Reworked DP aux/audio support
- Added SM6350 DP to the bindings
- GPU:
- a7xx perfcntr reg fixes
- MAINTAINERS updates
- a750 devcoredump support
radeon:
- Silence UBSAN warnings related to flexible arrays
nouveau:
- move some uAPI objects to uapi headers
omapdrm:
- console fix
ast:
- add i2c polling
qaic:
- add debugfs entries
exynos:
- fix platform_driver .owner
- drop cleanup code
mediatek:
- Use devm_platform_get_and_ioremap_resource() in mtk_hdmi_ddc_probe()
- Add GAMMA 12-bit LUT support for MT8188
- Rename mtk_drm_* to mtk_*
- Drop driver owner initialization
- Correct calculation formula of PHY Timing"
* tag 'drm-next-2024-05-15' of https://gitlab.freedesktop.org/drm/kernel: (1477 commits)
drm/xe/ads: Use flexible-array
drm/xe: Use ordered WQ for G2H handler
drm/msm/gen_header: allow skipping the validation
drm/msm/a6xx: Cleanup indexed regs const'ness
drm/msm: Add devcoredump support for a750
drm/msm: Adjust a7xx GBIF debugbus dumping
drm/msm: Update a6xx registers XML
drm/msm: Fix imported a750 snapshot header for upstream
drm/msm: Import a750 snapshot registers from kgsl
MAINTAINERS: Add Konrad Dybcio as a reviewer for the Adreno driver
MAINTAINERS: Add a separate entry for Qualcomm Adreno GPU drivers
drm/msm/a6xx: Avoid a nullptr dereference when speedbin setting fails
drm/msm/adreno: fix CP cycles stat retrieval on a7xx
drm/msm/a7xx: allow writing to CP_BV counter selection registers
drm: zynqmp_dpsub: Always register bridge
Revert "drm/bridge: ti-sn65dsi83: Fix enable error path"
drm/fb_dma: Add checks in drm_fb_dma_get_scanout_buffer()
drm/fbdev-generic: Do not set physical framebuffer address
drm/panthor: Fix the FW reset logic
drm/panthor: Make sure we handle 'unknown group state' case properly
...
Linux 6.9-rc5
I've had a persistent msm failure on clang, and the fix is in fixes
so just pull it back to fix that.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The .bpc = 6 implies .bus_format = MEDIA_BUS_FMT_RGB666_1X7X3_SPWG ,
add the missing bus_format. Add missing connector type and bus_flags
as well.
Documentation [1] 1.4 GENERAL SPECIFICATI0NS indicates this panel is
capable of both RGB 18bit/24bit panel, the current configuration uses
18bit mode, .bus_format = MEDIA_BUS_FMT_RGB666_1X7X3_SPWG , .bpc = 6.
Support for the 24bit mode would require another entry in panel-simple
with .bus_format = MEDIA_BUS_FMT_RGB666_1X7X4_SPWG and .bpc = 8, which
is out of scope of this fix.
[1] https://www.distec.de/fileadmin/pdf/produkte/TFT-Displays/Innolux/G121X1-L03_Datasheet.pdf
Fixes: f8fa17ba81 ("drm/panel: simple: Add support for Innolux G121X1-L03")
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240328102746.17868-2-marex@denx.de
If we're using the AUX channel for eDP backlight and it fails to probe
for some reason, let's _not_ fail the panel probe.
At least one case where we could fail to init the backlight is because
of a dead or physically missing panel. As talked about in detail in
the earlier patch in this series, ("drm/panel-edp: If we fail to
powerup/get EDID, use conservative timings"), this can cause the
entire system's display pipeline to fail to come up and that's
non-ideal.
If we fail to init the backlight for some transitory reason, we should
dig in and see if there's a way to fix this (perhaps retries?). Even
in that case, though, having a panel whose backlight is stuck at 100%
(the default, at least in the panel Samsung ATNA33XC20 I tested) is
better than having no panel at all.
Reviewed-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240325145626.3.I552e8af0ddb1691cc0fe5d27ea3d8020e36f7006@changeid
If at boot we fail to power up the eDP panel (most often happens if
the eDP panel never asserts HPD to us) or if we are unable to read the
EDID at bootup to figure out the panel's ID then let's use the
conservative eDP panel powerup/powerdown timings but _not_ fail the
probe.
It might seem strange to _not_ fail the probe in this case since we
were unable to powerup the panel and confirm it's there. However,
there is a reason to do this. Specifically, if we fail to probe the
panel then it really throws the whole display pipeline for loop. Most
DRM subsystems are written so that they wait until all components
(including the panel) have probed before they set everything up. When
the panel doesn't come up then this never happens. As a side effect of
not setting everything up then other display adapters don't get
initialized. As a practical example, I can see that if I open up a
sc7180-trogdor based Chromebook that's using the generic "edp-panel"
and unplug the eDP panel that it causes the _external_ DP monitor not
to function. This is obviously bad because it means that a device with
a dead eDP panel becomes e-waste when it could instead still be given
useful life with an external display.
NOTES:
- When we fail to probe like this, boot is a bit slow because we try
several times to power the panel up. This doesn't feel horrible
because it'll eventually work and the retries are known to help
bring some panels up.
- In the case where we hit the condition of failing to power up, the
display will likely _never_ have a chance to work again until
reboot. Once the panel-edp pm_runtime resume function fails it
doesn't ever seem to retry. This is probably for the best given that
we don't have any real timing/modes. eDP isn't expected to be
"hotplugged" so this makes some sense.
- It turns out that this makes panel-edp behave more similarly for
users of the generic "edp-panel" compatible string and the old fixed
panel compatible string. With the old fixed panel compatible string
we don't talk to the panel during probe so we'd actually behave much
the same way that we'll now behave for the generic "edp-panel".
Reviewed-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240325145626.2.Ia7a55a9657b0b6aa4644fd497a0bc595a771258c@changeid
Most of our helpers have relied on being selected so far through
Kconfig, but that creates issues when we have multiple layers of helpers
with some depending on others.
Indeed, select doesn't select a dependency's dependencies, and thus
isn't super intuitive. Depends on however doesn't have that limitation,
so we can just switch all the drivers that were selecting
DRM_DISPLAY_DP_HELPER to depend on it.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://lore.kernel.org/r/20240327-kms-kconfig-helpers-v3-10-eafee11b84b3@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Most of our helpers have relied on being selected so far through
Kconfig, but that creates issues when we have multiple layers of helpers
with some depending on others.
Indeed, select doesn't select a dependency's dependencies, and thus
isn't super intuitive. Depends on however doesn't have that limitation,
so we can just switch all the drivers that were selecting
DRM_DISPLAY_DP_AUX_BUS to depend on it.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://lore.kernel.org/r/20240327-kms-kconfig-helpers-v3-9-eafee11b84b3@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Most of our helpers have relied on being selected so far through
Kconfig, but that creates issues when we have multiple layers of helpers
with some depending on others.
Indeed, select doesn't select a dependency's dependencies, and thus
isn't super intuitive. Depends on however doesn't have that limitation,
so we can just switch all the drivers that were selecting
DRM_DISPLAY_HELPER to depend on it.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://lore.kernel.org/r/20240327-kms-kconfig-helpers-v3-8-eafee11b84b3@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
It's found that some panels have variants that they share the same panel id
although their EDID and names are different. Besides panel id, now we need
more information from the EDID base block to distinguish these panel
variants.
Add drm_edid_read_base_block() to return the EDID base block, which is
wrapped in struct drm_edid.
Caller can further use it to get panel id or check if the block contains
certain strings, such as panel name.
Merge drm_edid_get_panel_id() and edid_extract_panel_id() into one
function.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240307230653.1807557-2-hsinyi@chromium.org
Pull drm updates from Dave Airlie:
"Highlights are usual, more AMD IP blocks for future hw, i915/xe
changes, Displayport tunnelling support for i915, msm YUV over DP
changes, new tests for ttm, but its mostly a lot of stuff all over the
place from lots of people.
core:
- EDID cleanups
- scheduler error handling fixes
- managed: add drmm_release_action() with tests
- add ratelimited drm debug print
- DPCD PSR early transport macro
- DP tunneling and bandwidth allocation helpers
- remove built-in edids
- dp: Avoid AUX transfers on powered-down displays
- dp: Add VSC SDP helpers
cross drivers:
- use new drm print helpers
- switch to ->read_edid callback
- gem: add stats for shared buffers plus updates to amdgpu, i915, xe
syncobj:
- fixes to waiting and sleeping
ttm:
- add tests
- fix errno codes
- simply busy-placement handling
- fix page decryption
media:
- tc358743: fix v4l device registration
video:
- move all kernel parameters for video behind CONFIG_VIDEO
sound:
- remove <drm/drm_edid.h> include from header
ci:
- add tests for msm
- fix apq8016 runner
efifb:
- use copy of global screen_info state
vesafb:
- use copy of global screen_info state
simplefb:
- fix logging
bridge:
- ite-6505: fix DP link-training bug
- samsung-dsim: fix error checking in probe
- samsung-dsim: add bsh-smm-s2/pro boards
- tc358767: fix regmap usage
- imx: add i.MX8MP HDMI PVI plus DT bindings
- imx: add i.MX8MP HDMI TX plus DT bindings
- sii902x: fix probing and unregistration
- tc358767: limit pixel PLL input range
- switch to new drm_bridge_read_edid() interface
panel:
- ltk050h3146w: error-handling fixes
- panel-edp: support delay between power-on and enable; use put_sync
in unprepare; support Mediatek MT8173 Chromebooks, BOE NV116WHM-N49
V8.0, BOE NV122WUM-N41, CSO MNC207QS1-1 plus DT bindings
- panel-lvds: support EDT ETML0700Z9NDHA plus DT bindings
- panel-novatek: FRIDA FRD400B25025-A-CTK plus DT bindings
- add BOE TH101MB31IG002-28A plus DT bindings
- add EDT ETML1010G3DRA plus DT bindings
- add Novatek NT36672E LCD DSI plus DT bindings
- nt36523: support 120Hz timings, fix includes
- simple: fix display timings on RK32FN48H
- visionox-vtdr6130: fix initialization
- add Powkiddy RGB10MAX3 plus DT bindings
- st7703: support panel rotation plus DT bindings
- add Himax HX83112A plus DT bindings
- ltk500hd1829: add support for ltk101b4029w and admatec 9904370
- simple: add BOE BP082WX1-100 8.2" panel plus DT bindungs
panel-orientation-quirks:
- GPD Win Mini
amdgpu:
- Validate DMABuf imports in compute VMs
- Add RAS ACA framework
- PSP 13 fixes
- Misc code cleanups
- Replay fixes
- Atom interpretor PS, WS bounds checking
- DML2 fixes
- Audio fixes
- DCN 3.5 Z state fixes
- Remove deprecated ida_simple usage
- UBSAN fixes
- RAS fixes
- Enable seq64 infrastructure
- DC color block enablement
- Documentation updates
- DC documentation updates
- DMCUB updates
- ATHUB 4.1 support
- LSDMA 7.0 support
- JPEG DPG support
- IH 7.0 support
- HDP 7.0 support
- VCN 5.0 support
- SMU 13.0.6 updates
- NBIO 7.11 updates
- SDMA 6.1 updates
- MMHUB 3.3 updates
- DCN 3.5.1 support
- NBIF 6.3.1 support
- VPE 6.1.1 support
amdkfd:
- Validate DMABuf imports in compute VMs
- SVM fixes
- Trap handler updates and enhancements
- Fix cache size reporting
- Relocate the trap handler
radeon:
- Atom interpretor PS, WS bounds checking
- Misc code cleanups
xe:
- new query for GuC submission version
- Remove unused persistent exec_queues
- Add vram frequency sysfs attributes
- Add the flag XE_VM_BIND_FLAG_DUMPABLE
- Drop pre-production workarounds
- Drop kunit tests for unsupported platforms
- Start pumbling SR-IOV support with memory based interrupts for VF
- Allow to map BO in GGTT with PAT index corresponding to XE_CACHE_UC
to work with memory based interrupts
- Add GuC Doorbells Manager as prep work SR-IOV
- Implement additional workarounds for xe2 and MTL
- Program a few registers according to perfomance guide spec for Xe2
- Fix remaining 32b build issues and enable it back
- Fix build with CONFIG_DEBUG_FS=n
- Fix warnings from GuC ABI headers
- Introduce Relay Communication for SR-IOV for VF <-> GuC <-> PF
- Release mmap mappings on rpm suspend
- Disable mid-thread preemption when not properly supported by
hardware
- Fix xe_exec by reserving extra fence slot for CPU bind
- Fix xe_exec with full long running exec queue
- Canonicalize addresses where needed for Xe2 and add to devcoredum
- Toggle USM support for Xe2
- Only allow 1 ufence per exec / bind IOCTL
- Add GuC firmware loading for Lunar Lake
- Add XE_VMA_PTE_64K VMA flag
i915:
- Add more ADL-N PCI IDs
- Enable fastboot also on older platforms
- Early transport for panel replay and PSR
- New ARL PCI IDs
- DP TPS4 PHY test pattern support
- Unify and improve VSC SDP for PSR and non-PSR cases
- Refactor memory regions and improve debug logging
- Rework global state serialization
- Remove unused CDCLK divider fields
- Unify HDCP connector logging format
- Use display instead of graphics version in display code
- Move VBT and opregion debugfs next to the implementation
- Abstract opregion interface, use opaque type
- MTL fixes
- HPD handling fixes
- Add GuC submission interface version query
- Atomically invalidate userptr on mmu-notifier
- Update handling of MMIO triggered reports
- Don't make assumptions about intel_wakeref_t type
- Extend driver code of Xe_LPG to Xe_LPG+
- Add flex arrays to struct i915_syncmap
- Allow for very slow HuC loading
- DP tunneling and bandwidth allocation support
msm:
- Correct bindings for MSM8976 and SM8650 platforms
- Start migration of MDP5 platforms to DPU driver
- X1E80100 MDSS support
- DPU:
- Improve DSC allocation, fixing several important corner cases
- Add support for SDM630/SDM660 platforms
- Simplify dpu_encoder_phys_ops
- Apply fixes targeting DSC support with a single DSC encoder
- Apply fixes for HCTL_EN timing configuration
- X1E80100 support
- Add support for YUV420 over DP
- GPU:
- fix sc7180 UBWC config
- fix a7xx LLC config
- new gpu support: a305B, a750, a702
- machine support: SM7150 (different power levels than other a618)
- a7xx devcoredump support
habanalabs:
- configure IRQ affinity according to NUMA node
- move HBM MMU page tables inside the HBM
- improve device reset
- check extended PCIe errors
ivpu:
- updates to firmware API
- refactor BO allocation
imx:
- use devm_ functions during init
hisilicon:
- fix EDID includes
mgag200:
- improve ioremap usage
- convert to struct drm_edid
- Work around PCI write bursts
nouveau:
- disp: use kmemdup()
- fix EDID includes
- documentation fixes
qaic:
- fixes to BO handling
- make use of DRM managed release
- fix order of remove operations
rockchip:
- analogix_dp: get encoder port from DT
- inno_hdmi: support HDMI for RK3128
- lvds: error-handling fixes
ssd130x:
- support SSD133x plus DT bindings
tegra:
- fix error handling
tilcdc:
- make use of DRM managed release
v3d:
- show memory stats in debugfs
- Support display MMU page size
vc4:
- fix error handling in plane prepare_fb
- fix framebuffer test in plane helpers
virtio:
- add venus capset defines
vkms:
- fix OOB access when programming the LUT
- Kconfig improvements
vmwgfx:
- unmap surface before changing plane state
- fix memory leak in error handling
- documentation fixes
- list command SVGA_3D_CMD_DEFINE_GB_SURFACE_V4 as invalid
- fix null-pointer deref in execbuf
- refactor display-mode probing
- fix fencing for creating cursor MOBs
- fix cursor-memory lifetime
xlnx:
- fix live video input for ZynqMP DPSUB
lima:
- fix memory leak
loongson:
- fail if no VRAM present
meson:
- switch to new drm_bridge_read_edid() interface
renesas:
- add RZ/G2L DU support plus DT bindings
mxsfb:
- Use managed mode config
sun4i:
- HDMI: updates to atomic mode setting
mediatek:
- Add display driver for MT8188 VDOSYS1
- DSI driver cleanups
- Filter modes according to hardware capability
- Fix a null pointer crash in mtk_drm_crtc_finish_page_flip
etnaviv:
- enhancements for NPU and MRT support"
* tag 'drm-next-2024-03-13' of https://gitlab.freedesktop.org/drm/kernel: (1420 commits)
drm/amd/display: Removed redundant @ symbol to fix kernel-doc warnings in -next repo
drm/amd/pm: wait for completion of the EnableGfxImu message
drm/amdgpu/soc21: add mode2 asic reset for SMU IP v14.0.1
drm/amdgpu: add smu 14.0.1 support
drm/amdgpu: add VPE 6.1.1 discovery support
drm/amdgpu/vpe: add VPE 6.1.1 support
drm/amdgpu/vpe: don't emit cond exec command under collaborate mode
drm/amdgpu/vpe: add collaborate mode support for VPE
drm/amdgpu/vpe: add PRED_EXE and COLLAB_SYNC OPCODE
drm/amdgpu/vpe: add multi instance VPE support
drm/amdgpu/discovery: add nbif v6_3_1 ip block
drm/amdgpu: Add nbif v6_3_1 ip block support
drm/amdgpu: Add pcie v6_1_0 ip headers (v5)
drm/amdgpu: Add nbif v6_3_1 ip headers (v5)
arch/powerpc: Remove <linux/fb.h> from backlight code
macintosh/via-pmu-backlight: Include <linux/backlight.h>
fbdev/chipsfb: Include <linux/backlight.h>
drm/etnaviv: Restore some id values
drm/amdkfd: make kfd_class constant
drm/amdgpu: add ring timeout information in devcoredump
...
