Similar to what has already been changed for eMMC and the MMC_SEND_OP_COND
(CMD1), let's convert the SD_APP_OP_COND (ACMD41) for SD cards to use the
common __mmc_poll_for_busy() too.
This change means the initial delay period, that starts as 10ms will now
increase for every loop when being busy. The total accepted timeout for
being busy is 1s, which is according to the SD spec.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Felix Qin <xiaokeqinhealth@126.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Link: https://lore.kernel.org/r/20240425133034.79599-1-ulf.hansson@linaro.org
Some mmc host drivers may need to fixup a card-detection GPIO's config
to e.g. enable the GPIO controllers builtin pull-up resistor on devices
where the firmware description of the GPIO is broken (e.g. GpioInt with
PullNone instead of PullUp in ACPI DSDT).
Since this is the exception rather then the rule adding a config
parameter to mmc_gpiod_request_cd() seems undesirable, so instead
add a new mmc_gpiod_set_cd_config() function. This is simply a wrapper
to call gpiod_set_config() on the card-detect GPIO acquired through
mmc_gpiod_request_cd().
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240410191639.526324-2-hdegoede@redhat.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Modules registering driver with sdio_register_driver() might
forget to set .owner field. The field is used by some of other kernel
parts for reference counting (try_module_get()), so it is expected that
drivers will set it.
Solve the problem by moving this task away from the drivers to the core
code, just like we did for platform_driver in
commit 9447057eaf ("platform_device: use a macro instead of
platform_driver_register").
Since many drivers forget to set the .owner, this effectively will fix
them. Examples of fixed drivers are: ath6kl, b43, btsdio.c, ks7010,
libertas, MediaTek WiFi drivers, Realtek WiFi drivers, rsi, siano,
wilc1000, wl1251 and more.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20240329-module-owner-sdio-v1-1-e4010b11ccaa@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Per filesystems/sysfs.rst, show() should only use sysfs_emit()
or sysfs_emit_at() when formatting the value to be returned to user space.
coccinelle complains that there are still a couple of functions that use
snprintf(). Convert them to sysfs_emit().
sprintf() will be converted as weel if they have.
Generally, this patch is generated by
make coccicheck M=<path/to/file> MODE=patch \
COCCI=scripts/coccinelle/api/device_attr_show.cocci
No functional change intended
Signed-off-by: Li Zhijian <lizhijian@fujitsu.com>
Link: https://lore.kernel.org/r/20240314091512.1323650-1-lizhijian@fujitsu.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pull MMC updates from Ulf Hansson:
"MMC core:
- Drop the use of BLK_BOUNCE_HIGH
- Fix partition switch for GP3
- Remove usage of the deprecated ida_simple API
MMC host:
- cqhci: Update bouncing email-addresses in MAINTAINERS
- davinci_mmc: Use sg_miter for PIO
- dw_mmc-hi3798cv200: Convert the DT bindings to YAML
- dw_mmc-hi3798mv200: Add driver for the new dw_mmc variant
- fsl-imx-esdhc: A couple of corrections/updates to the DT bindings
- meson-mx-sdhc: Drop use of the ->card_hw_reset() callback
- moxart-mmc: Use sg_miter for PIO
- moxart-mmc: Fix accounting for DMA transfers
- mvsdio: Use sg_miter for PIO
- mxcmmc: Use sg_miter for PIO
- omap: Use sg_miter for PIO
- renesas,sdhi: Add support for R-Car V4M variant
- sdhci-esdhc-mcf: Use sg_miter for swapping
- sdhci-of-dwcmshc: Add support for Sophgo CV1800B and SG2002 variants
- sh_mmcif: Use sg_miter for PIO
- tmio: Avoid concurrent runs of mmc_request_done()"
* tag 'mmc-v6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (44 commits)
mmc: core: make mmc_host_class constant
mmc: core: Fix switch on gp3 partition
mmc: tmio: comment the ERR_PTR usage in this driver
mmc: mmc_spi: Don't mention DMA direction
mmc: dw_mmc: Remove unused of_gpio.h
mmc: dw_mmc: add support for hi3798mv200
dt-bindings: mmc: hisilicon,hi3798cv200-dw-mshc: add Hi3798MV200 binding
dt-bindings: mmc: dw-mshc-hi3798cv200: convert to YAML
mmc: dw_mmc-hi3798cv200: remove MODULE_ALIAS()
mmc: core: Use a struct device* as in-param to mmc_of_parse_clk_phase()
mmc: wmt-sdmmc: remove an incorrect release_mem_region() call in the .remove function
mmc: tmio: avoid concurrent runs of mmc_request_done()
dt-bindings: mmc: fsl-imx-mmc: Document the required clocks
mmc: sh_mmcif: Advance sg_miter before reading blocks
mmc: sh_mmcif: sg_miter must not be atomic
mmc: sdhci-esdhc-mcf: Flag the sg_miter as atomic
dt-bindings: mmc: fsl-imx-esdhc: add default and 100mhz state
mmc: core: constify the struct device_type usage
mmc: sdhci-of-dwcmshc: Add support for Sophgo CV1800B and SG2002
dt-bindings: mmc: sdhci-of-dwcmhsc: Add Sophgo CV1800B and SG2002 support
...
Pull block updates from Jens Axboe:
- MD pull requests via Song:
- Cleanup redundant checks (Yu Kuai)
- Remove deprecated headers (Marc Zyngier, Song Liu)
- Concurrency fixes (Li Lingfeng)
- Memory leak fix (Li Nan)
- Refactor raid1 read_balance (Yu Kuai, Paul Luse)
- Clean up and fix for md_ioctl (Li Nan)
- Other small fixes (Gui-Dong Han, Heming Zhao)
- MD atomic limits (Christoph)
- NVMe pull request via Keith:
- RDMA target enhancements (Max)
- Fabrics fixes (Max, Guixin, Hannes)
- Atomic queue_limits usage (Christoph)
- Const use for class_register (Ricardo)
- Identification error handling fixes (Shin'ichiro, Keith)
- Improvement and cleanup for cached request handling (Christoph)
- Moving towards atomic queue limits. Core changes and driver bits so
far (Christoph)
- Fix UAF issues in aoeblk (Chun-Yi)
- Zoned fix and cleanups (Damien)
- s390 dasd cleanups and fixes (Jan, Miroslav)
- Block issue timestamp caching (me)
- noio scope guarding for zoned IO (Johannes)
- block/nvme PI improvements (Kanchan)
- Ability to terminate long running discard loop (Keith)
- bdev revalidation fix (Li)
- Get rid of old nr_queues hack for kdump kernels (Ming)
- Support for async deletion of ublk (Ming)
- Improve IRQ bio recycling (Pavel)
- Factor in CPU capacity for remote vs local completion (Qais)
- Add shared_tags configfs entry for null_blk (Shin'ichiro
- Fix for a regression in page refcounts introduced by the folio
unification (Tony)
- Misc fixes and cleanups (Arnd, Colin, John, Kunwu, Li, Navid,
Ricardo, Roman, Tang, Uwe)
* tag 'for-6.9/block-20240310' of git://git.kernel.dk/linux: (221 commits)
block: partitions: only define function mac_fix_string for CONFIG_PPC_PMAC
block/swim: Convert to platform remove callback returning void
cdrom: gdrom: Convert to platform remove callback returning void
block: remove disk_stack_limits
md: remove mddev->queue
md: don't initialize queue limits
md/raid10: use the atomic queue limit update APIs
md/raid5: use the atomic queue limit update APIs
md/raid1: use the atomic queue limit update APIs
md/raid0: use the atomic queue limit update APIs
md: add queue limit helpers
md: add a mddev_is_dm helper
md: add a mddev_add_trace_msg helper
md: add a mddev_trace_remap helper
bcache: move calculation of stripe_size and io_opt into bcache_device_init
virtio_blk: Do not use disk_set_max_open/active_zones()
aoe: fix the potential use-after-free problem in aoecmd_cfg_pkts
block: move capacity validation to blkpg_do_ioctl()
block: prevent division by zero in blk_rq_stat_sum()
drbd: atomically update queue limits in drbd_reconsider_queue_parameters
...
Merge the mmc fixes for v6.8-rc[n] into the next branch, to allow them to
get tested together with the new mmc changes that are targeted for v6.9.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit e7794c14fd ("mmc: rpmb: fixes pause retune on all RPMB
partitions.") added a mask check for 'part_type', but the mask used was
wrong leading to the code intended for rpmb also being executed for GP3.
On some MMCs (but not all) this would make gp3 partition inaccessible:
armadillo:~# head -c 1 < /dev/mmcblk2gp3
head: standard input: I/O error
armadillo:~# dmesg -c
[ 422.976583] mmc2: running CQE recovery
[ 423.058182] mmc2: running CQE recovery
[ 423.137607] mmc2: running CQE recovery
[ 423.137802] blk_update_request: I/O error, dev mmcblk2gp3, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 0
[ 423.237125] mmc2: running CQE recovery
[ 423.318206] mmc2: running CQE recovery
[ 423.397680] mmc2: running CQE recovery
[ 423.397837] blk_update_request: I/O error, dev mmcblk2gp3, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 423.408287] Buffer I/O error on dev mmcblk2gp3, logical block 0, async page read
the part_type values of interest here are defined as follow:
main 0
boot0 1
boot1 2
rpmb 3
gp0 4
gp1 5
gp2 6
gp3 7
so mask with EXT_CSD_PART_CONFIG_ACC_MASK (7) to correctly identify rpmb
Fixes: e7794c14fd ("mmc: rpmb: fixes pause retune on all RPMB partitions.")
Cc: stable@vger.kernel.org
Cc: Jorge Ramirez-Ortiz <jorge@foundries.io>
Signed-off-by: Dominique Martinet <dominique.martinet@atmark-techno.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240306-mmc-partswitch-v1-1-bf116985d950@codewreck.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pass the queue limit set at initialization time directly to
blk_mq_alloc_disk instead of updating it right after the allocation.
This requires refactoring the code a bit so that what was mmc_setup_queue
before also allocates the gendisk now and actually sets all limits.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20240215070300.2200308-18-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Merge the mmc fixes for v6.8-rc[n] into the next branch, to allow them to
get tested together with the new mmc changes that are targeted for v6.9.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Initializing an eMMC that's connected via a 1-bit bus is current failing,
if the HW (DT) informs that 4-bit bus is supported. In fact this is a
regression, as we were earlier capable of falling back to 1-bit mode, when
switching to 4/8-bit bus failed. Therefore, let's restore the behaviour.
Log for Samsung eMMC 5.1 chip connected via 1bit bus (only D0 pin)
Before patch:
[134509.044225] mmc0: switch to bus width 4 failed
[134509.044509] mmc0: new high speed MMC card at address 0001
[134509.054594] mmcblk0: mmc0:0001 BGUF4R 29.1 GiB
[134509.281602] mmc0: switch to bus width 4 failed
[134509.282638] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.282657] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[134509.284598] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.284602] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[134509.284609] ldm_validate_partition_table(): Disk read failed.
[134509.286495] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.286500] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[134509.288303] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.288308] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[134509.289540] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.289544] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[134509.289553] mmcblk0: unable to read partition table
[134509.289728] mmcblk0boot0: mmc0:0001 BGUF4R 31.9 MiB
[134509.290283] mmcblk0boot1: mmc0:0001 BGUF4R 31.9 MiB
[134509.294577] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2
[134509.295835] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.295841] Buffer I/O error on dev mmcblk0, logical block 0, async page read
After patch:
[134551.089613] mmc0: switch to bus width 4 failed
[134551.090377] mmc0: new high speed MMC card at address 0001
[134551.102271] mmcblk0: mmc0:0001 BGUF4R 29.1 GiB
[134551.113365] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 p19 p20 p21
[134551.114262] mmcblk0boot0: mmc0:0001 BGUF4R 31.9 MiB
[134551.114925] mmcblk0boot1: mmc0:0001 BGUF4R 31.9 MiB
Fixes: 577fb13199 ("mmc: rework selection of bus speed mode")
Cc: stable@vger.kernel.org
Signed-off-by: Ivan Semenov <ivan@semenov.dev>
Link: https://lore.kernel.org/r/20240206172845.34316-1-ivan@semenov.dev
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MMC core sets BLK_BOUNCE_HIGH for devices where dma_mask
is unassigned.
For the majority of MMC hosts this path is never taken: the
OF core will unconditionally assign a 32-bit mask to any
OF device, and most MMC hosts are probed from device tree,
see drivers/of/platform.c:
of_platform_device_create_pdata()
dev->dev.coherent_dma_mask = DMA_BIT_MASK(32);
if (!dev->dev.dma_mask)
dev->dev.dma_mask = &dev->dev.coherent_dma_mask;
of_amba_device_create()
dev->dev.coherent_dma_mask = DMA_BIT_MASK(32);
dev->dev.dma_mask = &dev->dev.coherent_dma_mask;
MMC devices that are probed from ACPI or PCI will likewise
have a proper dma_mask assigned.
The only remaining devices that could have a blank dma_mask
are platform devices instantiated from board files.
These are mostly used on systems without CONFIG_HIGHMEM
enabled which means the block layer will not bounce, and in
the few cases where it is enabled it is not used anyway:
for example some OMAP2 systems such as Nokia n800/n810 will
create a platform_device and not assign a dma_mask, however
they do not have any highmem, so no bouncing will happen
anyway: the block core checks if max_low_pfn >= max_pfn
and this will always be false.
Should it turn out there is a platform_device with blank
DMA mask actually using CONFIG_HIGHMEM somewhere out there
we should set dma_mask for it, not do this trickery.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240125-mmc-no-blk-bounce-high-v1-1-d0f92a30e085@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pull tty / serial updates from Greg KH:
"Here is the big set of tty and serial driver changes for 6.8-rc1.
As usual, Jiri has a bunch of refactoring and cleanups for the tty
core and drivers in here, along with the usual set of rs485 updates
(someday this might work properly...)
Along with those, in here are changes for:
- sc16is7xx serial driver updates
- platform driver removal api updates
- amba-pl011 driver updates
- tty driver binding updates
- other small tty/serial driver updates and changes
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (197 commits)
serial: sc16is7xx: refactor EFR lock
serial: sc16is7xx: reorder code to remove prototype declarations
serial: sc16is7xx: refactor FIFO access functions to increase commonality
serial: sc16is7xx: drop unneeded MODULE_ALIAS
serial: sc16is7xx: replace hardcoded divisor value with BIT() macro
serial: sc16is7xx: add explicit return for some switch default cases
serial: sc16is7xx: add macro for max number of UART ports
serial: sc16is7xx: add driver name to struct uart_driver
serial: sc16is7xx: use i2c_get_match_data()
serial: sc16is7xx: use spi_get_device_match_data()
serial: sc16is7xx: use DECLARE_BITMAP for sc16is7xx_lines bitfield
serial: sc16is7xx: improve do/while loop in sc16is7xx_irq()
serial: sc16is7xx: remove obsolete loop in sc16is7xx_port_irq()
serial: sc16is7xx: set safe default SPI clock frequency
serial: sc16is7xx: add check for unsupported SPI modes during probe
serial: sc16is7xx: fix invalid sc16is7xx_lines bitfield in case of probe error
serial: 8250_exar: Set missing rs485_supported flag
serial: omap: do not override settings for RS485 support
serial: core, imx: do not set RS485 enabled if it is not supported
serial: core: make sure RS485 cannot be enabled when it is not supported
...
Requesting a retune before switching to the RPMB partition has been
observed to cause CRC errors on the RPMB reads (-EILSEQ).
Since RPMB reads can not be retried, the clients would be directly
affected by the errors.
This commit disables the retune request prior to switching to the RPMB
partition: mmc_retune_pause() no longer triggers a retune before the
pause period begins.
This was verified with the sdhci-of-arasan driver (ZynqMP) configured
for HS200 using two separate eMMC cards (DG4064 and 064GB2). In both
cases, the error was easy to reproduce triggering every few tenths of
reads.
With this commit, systems that were utilizing OP-TEE to access RPMB
variables will experience an enhanced performance. Specifically, when
OP-TEE is configured to employ RPMB as a secure storage solution, it not
only writes the data but also the secure filesystem within the
partition. As a result, retrieving any variable involves multiple RPMB
reads, typically around five.
For context, on ZynqMP, each retune request consumed approximately
8ms. Consequently, reading any RPMB variable used to take at the very
minimum 40ms.
After droping the need to retune before switching to the RPMB partition,
this is no longer the case.
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Acked-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240103112911.2954632-1-jorge@foundries.io
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The eMMC card can be set into write-protected mode to prevent data from
being accidentally modified or deleted. Wp_grp_size (Write Protect Group
Size) refers to an attribute of the eMMC card, used to manage write
protection and is the CSD register [36:32] of the eMMC device. Wp_grp_size
(Write Protect Group Size) indicates how many eMMC blocks are contained in
each write protection group on the eMMC card.
To allow userspace easy access of the CSD register bits, let's add sysfs
node "wp_grp_size".
Signed-off-by: Lin Gui <lin.gui@mediatek.com>
Signed-off-by: Bo Ye <bo.ye@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20231218230532.82427-1-bo.ye@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a test to repeatedly re-tune in between random reads. The test is
non-destructive of data on the card and runs for 30 seconds. It can be
repeated to test for longer durations.
If re-tuning is not supported, the test is skipped.
Example:
# echo 'mmc1:0001' > /sys/bus/mmc/drivers/mmcblk/unbind
# echo 'mmc1:0001' > /sys/bus/mmc/drivers/mmc_test/bind
[ 36.642257] mmc_test mmc1:0001: Card claimed for testing.
# cat /sys/kernel/debug/mmc1/mmc1\:0001/testlist | grep tuning
52: Re-tuning reliability
# echo 52 > /sys/kernel/debug/mmc1/mmc1\:0001/test
[ 91.522555] mmc1: Starting tests of card mmc1:0001...
[ 91.528425] mmc1: Test case 52. Re-tuning reliability...
[ 121.536682] mmc1: Result: OK
[ 121.539572] mmc1: Tests completed.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20231214090902.43628-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Merge the mmc fixes for v6.7-rc[n] into the next branch, to allow them to
get tested together with the new mmc changes that are targeted for v6.8.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Merge the mmc fixes for v6.7-rc[n] into the next branch, to allow them to
get tested together with the new mmc changes that are targeted for v6.8.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When RPMB was converted to a character device, it added support for
multiple RPMB partitions (Commit 97548575be ("mmc: block: Convert RPMB to
a character device").
One of the changes in this commit was transforming the variable target_part
defined in __mmc_blk_ioctl_cmd into a bitmask. This inadvertently regressed
the validation check done in mmc_blk_part_switch_pre() and
mmc_blk_part_switch_post(), so let's fix it.
Fixes: 97548575be ("mmc: block: Convert RPMB to a character device")
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231201153143.1449753-1-jorge@foundries.io
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Field Firmware Update (ffu) may use close-ended or open ended sequence.
Each such sequence is comprised of a write commands enclosed between 2
switch commands - to and from ffu mode. So for the close-ended case, it
will be: cmd6->cmd23-cmd25-cmd6.
Some host controllers however, get confused when multi-block rw is sent
without sbc, and may generate auto-cmd12 which breaks the ffu sequence.
I encountered this issue while testing fwupd (github.com/fwupd/fwupd)
on HP Chromebook x2, a qualcomm based QC-7c, code name - strongbad.
Instead of a quirk, or hooking the request function of the msm ops,
it would be better to fix the ioctl handling and make it use mrq.sbc
instead of issuing SET_BLOCK_COUNT separately.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231129092535.3278-1-avri.altman@wdc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
During board verification, there is a need to test the various supported
eMMC/SD speed modes. However, since the framework chooses the best mode
supported by the card and the host controller's caps, this currently
necessitates changing the devicetree for every iteration.
Allow the various speed mode host capabilities to be modified via
debugfs in order to allow easier hardware verification. The values to
be written are the raw MMC_CAP* values from include/linux/mmc/host.h.
This is rather low-level, and these defines are not guaranteed to be
stable, but it is perhaps good enough for the intended use case.
MMC_CAP_AGGRESSIVE_PM can also be set, in order to be able to
re-initialize the card without having to physically remove and re-insert
it.
/sys/kernel/debug/mmc0# grep timing ios
timing spec: 9 (mmc HS200)
// Turn on MMC_CAP_AGGRESSIVE_PM and re-trigger runtime suspend
/sys/kernel/debug/mmc0# echo $(($(cat caps) | (1 << 7))) > caps
/sys/kernel/debug/mmc0# echo on > /sys/bus/mmc/devices/mmc0\:0001/power/control
/sys/kernel/debug/mmc0# echo auto > /sys/bus/mmc/devices/mmc0\:0001/power/control
// MMC_CAP2_HS200_1_8V_SDR
/sys/kernel/debug/mmc0# echo $(($(cat caps2) & ~(1 << 5))) > caps2
/sys/kernel/debug/mmc0# echo on > /sys/bus/mmc/devices/mmc0\:0001/power/control
/sys/kernel/debug/mmc0# grep timing ios
timing spec: 8 (mmc DDR52)
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20230929-mmc-caps-v2-2-11a4c2d94f15@axis.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
