This device is a gray USB parallel port adapter with "F5U002" imprinted
on the plastic and a sticker that says both "F5U002" and "P80453-A".
It's identified in lsusb as "05ab:1001 In-System Design BAYI Printer
Class Support". It's subtly different from the other gray cable I have
that has "F5U002 Rev 2" and "P80453-B" on its sticker and device ID
050d:0002.
The uss720 driver appears to work flawlessly with this device, although
the device evidently does not support ECP.
Signed-off-by: Alex Henrie <alexhenrie24@gmail.com>
Link: https://lore.kernel.org/r/20240326150723.99939-4-alexhenrie24@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The XMOS XVF3500 VocalFusion Voice Processor[1] is a low-latency, 32-bit
multicore controller for voice processing.
This device requires a specific power sequence, which consists of
enabling the regulators that control the 3V3 and 1V0 device supplies,
and a reset de-assertion after a delay of at least 100ns.
Once in normal operation, the XVF3500 registers itself as a USB device,
and it does not require any device-specific operations in the driver.
[1] https://www.xmos.com/xvf3500/
Acked-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Javier Carrasco <javier.carrasco@wolfvision.net>
Link: https://lore.kernel.org/r/20240325-onboard_xvf3500-v8-8-29e3f9222922@wolfvision.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most of the functionality this driver provides can be used by non-hub
devices as well.
To account for the hub-specific code, add a flag to the device data
structure and check its value for hub-specific code.
The 'always_powered_in_supend' attribute is only available for hub
devices, keeping the driver's default behavior for non-hub devices (keep
on in suspend).
Acked-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Javier Carrasco <javier.carrasco@wolfvision.net>
Link: https://lore.kernel.org/r/20240325-onboard_xvf3500-v8-6-29e3f9222922@wolfvision.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch prepares onboad_hub to support non-hub devices by renaming
the driver files and their content, the headers and their references.
The comments and descriptions have been slightly modified to keep
coherence and account for the specific cases that only affect onboard
hubs (e.g. peer-hub).
The "hub" variables in functions where "dev" (and similar names) variables
already exist have been renamed to onboard_dev for clarity, which adds a
few lines in cases where more than 80 characters are used.
No new functionality has been added.
Acked-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Javier Carrasco <javier.carrasco@wolfvision.net>
Link: https://lore.kernel.org/r/20240325-onboard_xvf3500-v8-2-29e3f9222922@wolfvision.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When auxiliary_device_add() returns error and then calls
auxiliary_device_uninit(), callback function ljca_auxdev_release
calls kfree(auxdev->dev.platform_data) to free the parameter data
of the function ljca_new_client_device. The callers of
ljca_new_client_device shouldn't call kfree() again
in the error handling path to free the platform data.
Fix this by cleaning up the redundant kfree() in all callers and
adding kfree() the passed in platform_data on errors which happen
before auxiliary_device_init() succeeds .
Fixes: acd6199f19 ("usb: Add support for Intel LJCA device")
Cc: stable <stable@kernel.org>
Signed-off-by: Yongzhi Liu <hyperlyzcs@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240311125748.28198-1-hyperlyzcs@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is usbdrv_wrap in struct usb_driver and usb_device_driver, it
contains device_driver and for_devices. for_devices is used to
distinguish between device drivers and interface drivers.
Like the is_usb_device(), it tests the type of the device. We can test
that if the probe of device_driver is equal to usb_probe_device in
is_usb_device_driver(), and then the struct usbdrv_wrap is no longer
needed.
Clean up struct usbdrv_wrap, use device_driver directly in struct
usb_driver and usb_device_driver. This makes the code cleaner.
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240104032822.1896596-1-yajun.deng@linux.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a general misunderstanding amongst engineers that {v}snprintf()
returns the length of the data *actually* encoded into the destination
array. However, as per the C99 standard {v}snprintf() really returns
the length of the data that *would have been* written if there were
enough space for it. This misunderstanding has led to buffer-overruns
in the past. It's generally considered safer to use the {v}scnprintf()
variants in their place (or even sprintf() in simple cases). So let's
do that.
Whilst we're at it, let's define some magic numbers to increase
readability and ease of maintenance.
Link: https://lwn.net/Articles/69419/
Link: https://github.com/KSPP/linux/issues/105
Cc: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20231213164246.1021885-9-lee@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Cypress CY7C6563x is a 2/4-port USB 2.0 hub. Add support for
this hub in the driver in order to bring up reset, supply or clock
dependencies.
There is no reset pulse width given in the datasheet so we expect
a minimal value of 1us to be enough. This hasn't been tested though
due to lack of hardware which has the reset connected to a GPIO.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/r/20231127112234.109073-3-frieder@fris.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most onboard USB hubs have a dedicated crystal oscillator but on some
boards the clock signal for the hub is provided by the SoC.
In order to support this, we add the possibility of specifying a
clock in the devicetree that gets enabled/disabled when the hub
is powered up/down.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/r/20231127112234.109073-2-frieder@fris.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the USB/PHY/Thunderbolt fixes in here as well for later patches
to build on top of.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable io_res is being assigned a value that is never read, it is
either being re-assigned a new value that is read later or it's not used
depending on the cases in the following switch statement. The assignment
is redundant and can be removed. Cleans up clang scan build warning:
drivers/usb/misc/iowarrior.c:504:2: warning: Value stored to 'io_res'
is never read [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20231111202656.339103-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implements the USB part of Intel USB-I2C/GPIO/SPI adapter device
named "La Jolla Cove Adapter" (LJCA).
The communication between the various LJCA module drivers and the
hardware will be muxed/demuxed by this driver. Three modules (
I2C, GPIO, and SPI) are supported currently.
Each sub-module of LJCA device is identified by type field within
the LJCA message header.
The sub-modules of LJCA can use ljca_transfer() to issue a transfer
between host and hardware. And ljca_register_event_cb is exported
to LJCA sub-module drivers for hardware event subscription.
The minimum code in ASL that covers this board is
Scope (\_SB.PCI0.DWC3.RHUB.HS01)
{
Device (GPIO)
{
Name (_ADR, Zero)
Name (_STA, 0x0F)
}
Device (I2C)
{
Name (_ADR, One)
Name (_STA, 0x0F)
}
Device (SPI)
{
Name (_ADR, 0x02)
Name (_STA, 0x0F)
}
}
Signed-off-by: Wentong Wu <wentong.wu@intel.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/1696833205-16716-2-git-send-email-wentong.wu@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the USB fixes in here for testing and for other patches to be
applied on top of.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The HX3 comes in different variants (up to 4 USB 3.0 ports; multi-TT),
e.g. CYUSB330x/CYUSB331x/CYUSB332x/CYUSB230x. It operates with two
different power supplies: 1V2 and 3V3.
Add the support for this hub, for controlling the reset pin and the
power supplies.
Reset time is extracted from data sheet, page 24:
"The RESETN pin can be tied to VDD_IO through an external resistor and
to ground (GND) through an external capacitor (minimum 5 ms time
constant)."
V_IH min is given at 0.7 * 3V3 (page 34), therefore use 10ms.
Also add USB PIDs for the USB 2.0 and USB 3.0 root hub.
Acked-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Benjamin Bara <benjamin.bara@skidata.com>
Link: https://lore.kernel.org/r/20230620-hx3-v7-2-f79b4b22a1bf@skidata.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Acked-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230718143027.1064731-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Genesys Logic GL3523 is a 4-port USB 3.1 hub that has a reset pin to
toggle and a 5.0V core supply exported though an integrated LDO is
available for powering it.
Add the support for this hub, for controlling the reset pin and the core
power supply.
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
[m.felsch@pengutronix.de: include review feedback & port to 6.4]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20230623142228.4069084-2-m.felsch@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If onboard_hub_power_off() called by onboard_hub_remove() fails it emits
an error message. Forwarding the returned error value to the driver core
results in another error message. As the return value is otherwise
ignored, just drop the return value. There is no side effect apart from
suppressing the core's warning.
Instead of returning zero unconditionally, convert to .remove_new()
which has the same semantics as .remove() that unconditionally returns
zero.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230530073633.2193618-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230517230239.187727-88-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Link: https://lore.kernel.org/r/20230517230239.187727-87-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USS720 parport driver source code is in drivers/usb/misc/, the
corresponding config is defined in drivers/usb/Kconfig. Some digging in the
kernel's history revealed no good reason why it needs to be defined in
USB's top-level Kconfig file, and why the config for the USS720 parport
driver should be the first in the list of USB port drivers, while all other
configs for drivers in drivers/usb/misc are in the USB Miscellaneous driver
configuration file.
Most probably, it was simply considered a bit more special when the USB
Miscellaneous driver configuration file (drivers/usb/misc/Config.in back
then) was initially created, and this config simply survived to remain at
the top-level USB Kconfig file with all further code/Kconfig
transformations and additions later on. Users rarely notice this config
being at this position, as CONFIG_PARPORT (Parallel port support) needs to
be enabled and only few users enable that. Nowadays, this USB_USS720 driver
is probably not that special that it needs to be listed as first item of
the USB port drivers.
Move the configuration of the USS720 parport driver to the top of the USB
Miscellaneous drivers section, as the configurations does not have a lot of
specific ordering USB Miscellaneous drivers. This way, the USS720 parport
driver is moved to the comment "USB Miscellaneous drivers", fitting to the
driver's source code location, but still is at the top of the list for
those few acquainted users of Kconfig UIs that might be looking for the
config that was once at the top of the list of the USB port drivers.
Put this config definition to a more local place. No semantic change.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20230329075125.32352-1-lukas.bulwahn@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the USB fixes here, and the USB gadget update for future
development patches to be based on.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver didn't see real maintainance since several years. It has
several trivial issues (check $(scripts/checkpatch.pl -f
drivers/usb/misc/ftdi-elan.c)) and some harder ones (difficult locking,
explict kref handling, ...). Also today it's hard to find hardware to
make actually use of such a card and I suspect the driver is completely
unused.
So remove it.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230321150919.351947-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
