- in device_resume, sriov configure interrupt should be in full access,
so release_full_gpu should be done after kfd_resume.
- remove the previous workaround solution for sriov.
Fixes: ec4927d463 ("drm/amdgpu: fix for suspend/resume sequence under sriov")
Signed-off-by: Shikang Fan <shikang.fan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If CONFIG_DRM_AMDGPU=y and CONFIG_DRM_AMD_DC is not set,
gcc complained about unused-function :
drivers/gpu/drm/amd/amdgpu/amdgpu_discovery.c:1705:13: error: ‘amdgpu_discovery_set_sriov_display’ defined but not used [-Werror=unused-function]
static void amdgpu_discovery_set_sriov_display(struct amdgpu_device *adev)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
To fix this error, use CONFIG_DRM_AMD_DC to wrap
the definition of amdgpu_discovery_set_sriov_display().
Fixes: 25263da376 ("drm/amdgpu: rework SR-IOV virtual display handling")
Signed-off-by: Ren Zhijie <renzhijie2@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
root cause that S2A need to use deduct offset flag.
after setting this flag, vcn0 doorbell value works.
so return it as before
Signed-off-by: Jane Jian <Jane.Jian@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As comment of pci_get_domain_bus_and_slot() says, it returns
a pci device with refcount increment, when finish using it,
the caller must decrement the reference count by calling
pci_dev_put().
So before returning from amdgpu_device_resume|suspend_display_audio(),
pci_dev_put() is called to avoid refcount leak.
Fixes: 3f12acc8d6 ("drm/amdgpu: put the audio codec into suspend state before gpu reset V3")
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
root cause that S2A need to use deduct offset flag.
after setting this flag, vcn0 doorbell value works.
so return it as before
Signed-off-by: Jane Jian <Jane.Jian@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amd-drm-next-6.2-2022-11-18:
amdgpu:
- SR-IOV fixes
- Clean up DC checks
- DCN 3.2.x fixes
- DCN 3.1.x fixes
- Don't enable degamma on asics which don't support it
- IP discovery fixes
- BACO fixes
- Fix vbios allocation handling when vkms is enabled
- Drop buggy tdr advanced mode GPU reset handling
- Fix the build when DCN is not set in kconfig
- MST DSC fixes
- Userptr fixes
- FRU and RAS EEPROM fixes
- VCN 4.x RAS support
- Aldrebaran CU occupancy reporting fix
- PSP ring cleanup
amdkfd:
- Memory limit fix
- Enable cooperative launch on gfx 10.3
amd-drm-next-6.2-2022-11-11:
amdgpu:
- SMU 13.x updates
- GPUVM TLB race fix
- DCN 3.1.4 updates
- DCN 3.2.x updates
- PSR fixes
- Kerneldoc fix
- Vega10 fan fix
- GPUVM locking fixes in error pathes
- BACO fix for Beige Goby
- EEPROM I2C address cleanup
- GFXOFF fix
- Fix DC memory leak in error pathes
- Flexible array updates
- Mtype fix for GPUVM PTEs
- Move Kconfig into amdgpu directory
- SR-IOV updates
- Fix possible memory leak in CS IOCTL error path
amdkfd:
- Fix possible memory overrun
- CRIU fixes
radeon:
- ACPI ref count fix
- HDA audio notifier support
- Move Kconfig into radeon directory
UAPI:
- Add new GEM_CREATE flags to help to transition more KFD functionality to the DRM UAPI.
These are used internally in the driver to align location based memory coherency
requirements from memory allocated in the KFD with how we manage GPUVM PTEs. They
are currently blocked in the GEM_CREATE IOCTL as we don't have a user right now.
They are just used internally in the kernel driver for now for existing KFD memory
allocations. So a change to the UAPI header, but no functional change in the UAPI.
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221118170807.6505-1-alexander.deucher@amd.com
Signed-off-by: Dave Airlie <airlied@redhat.com>
The basic problem here is that it's not allowed to page fault while
holding the reservation lock.
So it can happen that multiple processes try to validate an userptr
at the same time.
Work around that by putting the HMM range object into the mutex
protected bo list for now.
v2: make sure range is set to NULL in case of an error
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
CC: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
All of the IP specific versions are the same now, so
we can just use a common function.
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This matches what we do for psp 3.1 and makes ring_init
common for all PSP versions.
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Allow user to know number of compute units (CU) that are in use at any
given moment. Enable access to the method kgd_gfx_v9_get_cu_occupancy
that computes CU occupancy.
Signed-off-by: Ramesh Errabolu <Ramesh.Errabolu@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Don't assume FRU MCU memory locations for the FRU data fields, or their sizes,
instead read and interpret the IPMI data, as stipulated in the IPMI spec
version 1.0 rev 1.2.
Extract the Product Name, Product Part/Model Number, and the Product Serial
Number by interpreting the IPMI data.
Check the checksums of the stored IPMI data to make sure we don't read and
give corrupted data back the the user.
Eliminate small I2C reads, and instead read the whole Product Info Area in one
go, and then extract the information we're seeking from it.
Eliminates a whole function, making this file smaller.
v2: Clarify changes in the commit message.
Cc: Alex Deucher <Alexander.Deucher@amd.com>
Cc: Kent Russell <kent.russell@amd.com>
Signed-off-by: Luben Tuikov <luben.tuikov@amd.com>
Tested-by: Kent Russell <kent.russell@amd.com>
Reviewed-by: Kent Russell <kent.russell@amd.com>
Reviewed-by: Alex Deucher <Alexander.Deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm-misc-fixes for v6.1-rc6:
- Fix error handling in vc4_atomic_commit_tail()
- Set bpc for logictechno panels.
- Fix potential memory leak in drm_dev_init()
- Fix potential null-ptr-deref in drm_vblank_destroy_worker()
- Set lima's clkname corrrectly when regulator is missing.
- Small amdgpu fix to gang submission.
- Revert hiding unregistered connectors from userspace, as it breaks on DP-MST.
- Add workaround for DP++ dual mode adaptors that don't support
i2c subaddressing.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/c7d02936-c550-199b-6cb7-cbf6cf104e4a@linux.intel.com
The basic problem here is that it's not allowed to page fault while
holding the reservation lock.
So it can happen that multiple processes try to validate an userptr
at the same time.
Work around that by putting the HMM range object into the mutex
protected bo list for now.
v2: make sure range is set to NULL in case of an error
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
CC: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Re-submitting IBs by the kernel has many problems because pre-
requisite state is not automatically re-created as well. In
other words neither binary semaphores nor things like ring
buffer pointers are in the state they should be when the
hardware starts to work on the IBs again.
Additional to that even after more than 5 years of
developing this feature it is still not stable and we have
massively problems getting the reference counts right.
As discussed with user space developers this behavior is not
helpful in the first place. For graphics and multimedia
workloads it makes much more sense to either completely
re-create the context or at least re-submitting the IBs
from userspace.
For compute use cases re-submitting is also not very
helpful since userspace must rely on the accuracy of
the result.
Because of this we stop this practice and instead just
properly note that the fence submission was canceled. The
only use case we keep the re-submission for now is SRIOV
and function level resets.
v2: as suggested by Sshaoyun stop resubmitting jobs even for SRIOV
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit e6c6338f39.
This feature basically re-submits one job after another to
figure out which one was the one causing a hang.
This is obviously incompatible with gang-submit which requires
that multiple jobs run at the same time. It's also absolutely
not helpful to crash the hardware multiple times if a clean
recovery is desired.
For testing and debugging environments we should rather disable
recovery alltogether to be able to inspect the state with a hw
debugger.
Additional to that the sw implementation is clearly buggy and causes
reference count issues for the hardware fence.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Amdgpu_ras_set_error_query_ready is called at the start of
amdgpu_device_gpu_recover to disable query ras error, but the
code behind only enables query ras error in full reset path,
but not in soft reset path, emergency restart path and skip
the hardware reset path.
Signed-off-by: YiPeng Chai <YiPeng.Chai@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
