[Why]
For some EDP to MIPI panel, disabling OTG when link is alive like boot
case, the converter might output garbage or show no display because our
GPU is not sending required pixel data.
Alos Dig fifo underflow was found which might cause garbage, when
resetting otg for other types of EDP panels.
[How]
Skipping resetting OTG if the dig fifo is on. Make sure that the otg for
the pipe is the one that the dig fifo is selecting via the FE mask.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Zhongwei <Zhongwei.Zhang@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The MPO plane will receive a flip but
desktop plane may not receive a flip when GSL is enabled.
As a result, system will be stuck waiting for a flip that was never sent.
[How]
Set update address update flag of all flip_immediate planes
if there are multiple planes.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Austin Zheng <Austin.Zheng@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Resync FIFO is a workaround to write the same value to
DENTIST_DISPCLK_CNTL register after programming OTG_PIXEL_RATE_DIV
register, in case seemless boot, there is no OTG_PIXEL_RATE_DIV register
update, so skip CRTC disable when resync FIFO to avoid random FIFO error
and garbage.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Fudongwang <Fudong.Wang@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dcn32_blank_phantom() does not consider the subVP+ODM case when blanking.
Only one of the pipes will get blanked. Remaining pipes are not blanked.
Will cause underflow in the phantom pipe when enabling the CRTC.
[How]
Use blank_pixel_data() instead of blank_phantom().
remove dcn32_blank_phantom() since logic is identical.
Different DPG dimensions get programmed when blanking phantom pipes.
Previously had phantom pipes use DPG dimensions of the main stream.
Now use DPG dimensions of the phantom streams
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Austin Zheng <Austin.Zheng@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reorganize kerneldoc parameter names to match the parameter
order in the function header.
Problems identified using Coccinelle.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DC 3.2.303 contains some improvements as summarized below:
* Improve brightness control
* Add support for UHBR10 eDP
* OPTC required only for DTBCLK_P for dcn401
* Fix TBT monitor resume issue
* Code cleanup
Reviewed-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DTBCLK_P is used to generate virtual pixel clock, and to drive the HPO
stream encoder clock. Programming the required clock when
enabling/disabling both components can cause issues.
For example, if HPO is being disabled and clock source is changed to
REFCLK, virtual pixel rate will then be wrong, causing issues in CRTC.
[HOW]
Only program the DTBCLK_P when programming CRTC, as its expected it will
be enabled prior to HPO, and disabled after HPO in all valid cases.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This enables starting and stopping IPS residency measurements
and querying the IPS residency information consisting of residency
percent, entry counter, total time active & inactive, and histograms
for the specified IPS mode.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Ovidiu Bunea <Ovidiu.Bunea@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT & HOW]
MacroTileSizeBytes is set to either 256 or 65535 and it is never
4096. Its branch is not taken, and should be removed. Similarly,
mode_422 is always 0 and thus ppe will always be 1. The ternary
operator should be removed.
This fixes 2 DEADCODE issues reported by Coverity.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Prioritize Aux-based over PWM-based brightness control
for more types of panels and introduce a new structure
to store and manage the type of brightness control used.
Reviewed-by: Anthony Koo <anthony.koo@amd.com>
Signed-off-by: Muyuan Yang <muyuan.yang@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If two monitors with TMDS signals were timing synced and one was
disconnected, the stream would go out of sync too early due to
the PLL turning off and the system could hang
[How]
On link disable output, change PHY FSM transition from TX_EN-to-PHY_OFF
to TX_EN-to-PLL_ON for TMDS
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Ryan Seto <ryanseto@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Current state should be used when waiting for DET update
instead of new context.
For any streams decreasing in DET, pipes used in the current state
should be checked since those pipes need to free their DET before
DET can be reallocated.
[How]
Pass in current_state instead of context.
Use pipe from current_state instead of context. This assumes that
pipe in the current_state is an OTG_MASTER pipe if the pipe in the context is an OTG_MASTER pipe.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Austin Zheng <Austin.Zheng@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In cases where an MPO plane is being dragged around partially off-screen,
it is possible to get a flip where the only scaling parameters to change
are the clip rect size and position. Currently, clip rect size changes
are considered medium updates, which can result in the clip rect being used
for HW programming being larger than the clip rect that was used for the
last DML validation. This can lead to mismatches in different parts of the
pipe and can result in a p-state hang.
[How]
- consider clip rect size changes scaling changes, therefore full updates
- refactor get_scaling_info_update_type for clarity
- remove clip_size_change update flag
Clip rect size changes were previously demoted from full updates as an
optimization when the MPO + ODM policy changed to always pre-allocate MPO
pipes, but it created the issue described above. Personally testing this
use case, the performance feels fine with full update spam, and we expect
this is a fairly infrequent use case. If the performance needs to be
optimized in the future, consider reworking the entire update type logic
to run a DML pass and determine the update type based on what DML says
will actually change.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why/How]
Certain transitions from HW to SW cursor can be missed, which will
result in black visual confirm instead of expected blue/red. Need to add
handling for cursor visual confirm to dc_update_visual_confirm_color.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Videos using YUV420 format may result in high power being used.
Disabling MPO may result in lower power usage.
Update interface that can be used to check power profile of a dc_state.
[How]
Allow pstate switching in VBlank as last entry in strategy candidates.
Add helper functions that can be used to determine power level:
-get power profile after a dc_state has undergone full validation
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Austin Zheng <Austin.Zheng@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The "dpp35_dppclk_control" routine is incorrectly disabling the register clock gater
when the DPP is enabled.
The "DISPCLK_R_GATE_DISABLE" should never be set to 1 in the normal operating mode.
This will disable the clock gater and the DPPCLK register clock branch will always be running.
As a consequence, the dynamic power will be higher than expected.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Currently the absence of UHBR cable ID caps from USB-C PD does not block UHBR
rates. In situations where DPCD reports valid UHBR capability but USB-C PD
does not, such as using a USB-C to DP1.4 dongle connected to a native DP2.1
cable, link loss and lightup failures can be seen as a result.
Additionally, in edge cases where a platform supports cable ID but DMUB
doesn't correctly return cable ID caps, driver currently also allows UHBR.
[HOW]
Block UHBR rates over DP alt mode if cable id indicates no UHBR support.
Additionally, block UHBR rates if a cable ID supported platform receives no
reply from a DMUB cable id query.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Current pipe unlock order set within dcn401_interdependent_update_lock.
Separate the logic from the functionality to allow for unit testing
and make it easier to debug.
[How]
Add a flag to indicate if a pipe unlock order should be set.
Create function to determine unlock order.
Indicate which pipes should be unlocked first using
array stored in dc scratch memory.
Pipes indicated in array can be unlocked in any order.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Austin Zheng <Austin.Zheng@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Turning off OTG before DIG is on and backlight is on, might cause:
DIG FIFO underflow.
EDP output unexpected video data. That might violate EDP spec.
EDP spec requires black light should be off before validate
video data is turned off.
Currently garbage issue only occurs in one type of EDP to MIPI converter.
[How]
Add monitor patch to call blank_stream() before disable_crtc().
That will be no impact for current sequence.
If there are more types of EDP panels meeting this issue later,
we might remove this monitor patch and fix the current sequence.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Zhongwei <Zhongwei.Zhang@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
Before every full update we must wait for all pending updates to be
cleared - this is particularly important for minimal transitions
because if we don't wait for pending cleared, it will be as if
there was no minimal transition at all. In OTG we must read 3 different
status registers for pending cleared, one specifically for OTG updates,
one specifically for OPTC updates, and the last for surface related
updates.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix several copypaste mistakes in *_disable_link_output() functions where
an improper function pointer is checked before dereference.
Found by Linux Verification Center (linuxtesting.org) with Svace.
Signed-off-by: Vitaliy Shevtsov <v.shevtsov@maxima.ru>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch addresses warnings produced by the checkpatch script
related to unnecessary casts that could potentially hide bugs.
The specific warnings are as follows:
- Warning at drivers/gpu/drm/amd/display/dc/dml2/dml21/dml21_wrapper.c:16
- Warning at drivers/gpu/drm/amd/display/dc/dml2/dml21/dml21_wrapper.c:20
- Warning at drivers/gpu/drm/amd/display/dc/dml2/dml21/dml21_wrapper.c:30
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rohit Chavan <roheetchavan@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Correct the parameter descriptor for the function
`dc_process_dmub_dpia_set_tps_notification` to match the actual
parameters used.
Fixes the below with gcc W=1:
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc.c:5768: warning: Function parameter or struct member 'tps' not described in 'dc_process_dmub_dpia_set_tps_notification'
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc.c:5768: warning: Excess function parameter 'ts' description in 'dc_process_dmub_dpia_set_tps_notification'
Cc: Tom Chung <chiahsuan.chung@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Roman Li <roman.li@amd.com>
Cc: Alex Hung <alex.hung@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As set_drr() is called from IRQ context, it can happen that the
pipe context has been nulled by dc_state_destruct().
Apply the same protection here that is already present for
dcn35_set_drr() and dcn10_set_drr(). I.e. fetch the tg pointer
first (to avoid a race with dc_state_destruct()), and then
check the local copy before using it.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3142
Fixes: 06ad7e1642 ("drm/amd/display: Destroy DC context while keeping DML and DML2")
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Clear cached watermark after resume
- Update IPS default mode for DCN35/DCN351
- Use full update for swizzle mode change
- Skip to enable dsc if it has been off
- Fix underflow when setting underscan on DCN401
- Remove always-false branches
- Check null pointer before dereferencing se
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
1) We did linear/non linear transition properly long ago
2) We used that path to handle SystemDisplayEnable
3) We fixed a SystemDisplayEnable inability to fallback to passive by
impacting the transition flow generically
4) AFMF later relied on the generic transition behavior
Separating the two flows to make (3) non-generic is the best immediate
coarse of action.
DC can discern SSAMPO3 very easily from SDE.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Chris Park <chris.park@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
It makes DSC enable when we commit the stream which need
keep power off, and then it will skip to disable DSC if
pipe reset at this situation as power has been off. It may
cause the DSC unexpected enable on the pipe with the
next new stream which doesn't support DSC.
[HOW]
Check the DSC used on current pipe status when update stream.
Skip to enable if it has been off. The operation enable
DSC should happen when set power on.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Zhikai Zhai <zhikai.zhai@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT & HOW]
req128_c is always set to false and its branch is never taken.
Similarly, MacroTileSizeBytes is set to either 256 or 65535 and it is
never 4096 and it's branch is not taken.
Therefore, their branches are removed.
This fixes 3 DEADCODE issues reported by Coverity.
Acked-by: Alex Hung <alex.hung@amd.com>
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT & HOW]
se is null checked previously in the same function, indicating
it might be null; therefore, it must be checked when used again.
This fixes 1 FORWARD_NULL issue reported by Coverity.
Acked-by: Alex Hung <alex.hung@amd.com>
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
