Add initial 2 channel (stereo) support for Allo Piano DAC (2.0/2.1) boards,
using allo-piano-dac-pcm512x-audio overlay and allo-piano-dac ALSA ASoC
machine driver.
NB. The initial support is 2 channel (stereo) ONLY!
(The Piano DAC 2.1 will only support 2 channel (stereo) left/right output,
pending an update to the upstream pcm512x codec driver, which will have
to be submitted via upstream. With the initial downstream support,
provided by this patch, the Piano DAC 2.1 subwoofer outputs will
not function.)
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net>
Signed-off-by: Clive Messer <clive.messer@digitaldreamtime.co.uk>
Tested-by: Clive Messer <clive.messer@digitaldreamtime.co.uk>
Some evidence of curing disconnects with this disabled, so make it a default.
Can be overridden with module parameter roamoff=0
See: http://projectable.me/optimize-my-pi-wi-fi/
With the preceding commit:
bcm2835-sdhost: Don't exit cmd wait loop on error
it is safe to use the bcm2835-sdhost driver on the Compute Module.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The FAIL flag can be set in the CMD register before command processing
is complete, leading to spurious "failed to complete" errors. This has
the effect of promoting harmless CRC7 errors during CMD1 processing
into errors that can delay and even prevent booting.
Also:
1) Convert the last KERN_ERROR message in the register dumping to
KERN_INFO.
2) Remove an unnecessary reset call from bcm2835_sdhost_add_host.
See: https://github.com/raspberrypi/linux/pull/1492
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The bus rx sequence is not in order because that control and event
frames always cause immediate send, but data frames may be held
for glomming in firmware side. It is not actually an error as the
packets are still processed even if the RX sequence is not in order.
Therefore the error message is rephrased and changed to a debug
message.
[ Patch from Broadcom ]
See: https://github.com/raspberrypi/linux/issues/1313
When using nmap tool with FMAC, the nmap packets were be dropped by kernel
because the size was too short. The kernel message showed like
"nmap: packet size is too short (42 <= 50)". It is caused by the packet
length is shorter than ndev->hard_header_len. According to LL_RESERVED_SPACE()
and hard_header_len definition, we should use hard_header_len to reserve L2
header, like ethernet header(ETH_HLEN) in our case and use needed_headroom for
the additional headroom needed by hardware.
[ Patch from Broadcom ]
See: https://github.com/raspberrypi/linux/issues/1357
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The error message is given for something that is not an error here as
the drive strength configuration may not be applicable for specific
devices. Therefore the error message is rephrased and changed to a
debug message.
[ Patch from Broadcom ]
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
so that special/critical clocks can get enabled early on
in the boot process avoiding the risk of disabling a clock,
pll_divider or pll when a claiming driver fails to install
propperly - maybe it needs to defer.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Remove clk_core from device tree as it is no longer used.
Any "modification" to the core_clock in the bootloader is now
automatically detected via the cnew clockmgr.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
Moved uart0 to use new clock framework.
At the same time removed the fixed clock clk_uart0
and the corresponding references, as the clock is now
read directly from the configured clocks.
If it ever becomes necessary the following can get added
to modify the base clock rate later:
assigned-clocks = <&clocks BCM2835_CLOCK_UART>;
assigned-clock-rates = <X>;
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
Remove clk_core from device tree as it is no longer used.
Any "modification" to the core_clock in the bootloader is now
automatically detected via the cnew clockmgr.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Move the sdhost device to use the clock framework.
Unfortunately I can not test it on my CM, as it seem as if
there is no overlay that would enable sdhost and change the
gpio-mux to the correct ALT0 (from Alt3 from mmc).
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Move mmc to use clock framework.
For some reason the emmc clock dirver does not claim the
clock - enable count stays at 0 for the emmc clock.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Use clock manager instead of self-made clockmanager.
Also fix some error paths that showd up during development
(especially missing release of dma resources on rmmod)
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Move to new aux-uart driver (from upstream) and enable it correctly
in the device tree
Note that this may also solve the "serial not 115200 baud"
issue on the rpi3...
With an extension to the driver (requesting clock change
notifications) the driver could change the baud divider when
such a clock change occurs...
It still would require some communication between the firmware
and the kernel, so that this would get propagated.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Moved uart0 to use new clock framework.
At the same time removed the fixed clock clk_uart0
and the corresponding references, as the clock is now
read directly from the configured clocks.
If it ever becomes necessary the following can get added
to modify the base clock rate later:
assigned-clocks = <&clocks BCM2835_CLOCK_UART>;
assigned-clock-rates = <X>;
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Upstream mandates the use of "serial" as name inside the device-tree.
Note that this does not affect the use of the alias - there
uart0 and uart1 are permissible.
This also fixed the patch references inside the overlays for the rpi3.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
While the SDRAM is being driven by its dedicated PLL most of the time,
there is a little loop running in the firmware that periodically turns
on the CM SDRAM clock (using its pre-initialized parent) and switches
SDRAM to using the CM clock to do PVT recalibration.
This avoids system hangs if we choose SDRAM's parent for some other
clock, then disable that clock.
Signed-off-by: Eric Anholt <eric@anholt.net>
If the firmware had set up a clock to source from PLLC, go along with
it. But if we're looking for a new parent, we don't want to switch it
to PLLC because the firmware will force PLLC (and thus the AXI bus
clock) to different frequencies during over-temp/under-voltage,
without notification to Linux.
On my system, this moves the Linux-enabled HDMI state machine and DSI1
escape clock over to plld_per from pllc_per. EMMC still ends up on
pllc_per, because the firmware had set it up to use that.
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes: 41691b8862 ("clk: bcm2835: Add support for programming the audio domain clocks")
These divide off of PLLD_PER and are used for the ethernet and wifi
PHYs source PLLs. Neither of them is currently represented by a phy
device that would grab the clock for us.
This keeps other drivers from killing the networking PHYs when they
disable their own clocks and trigger PLLD_PER's refcount going to 0.
v2: Skip marking as critical if they aren't on at boot.
Signed-off-by: Eric Anholt <eric@anholt.net>
The VPU clock is also the clock for our AXI bus, so we really can't
disable it. This might have happened during boot if, for example,
uart1 (aux_uart clock) probed and was then disabled before the other
consumers of the VPU clock had probed.
v2: Rewrite to use a .flags in bcm2835_clock_data, since other clocks
will need this too.
Signed-off-by: Eric Anholt <eric@anholt.net>
To speed testing of the new sdhost driver that adapts to changes in
core_freq, hack the on-demand governor to treat io_is_busy=1 as
io_is_busy=0. The io_is_busy feature can still be forced using
io_is_busy=2.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Commit 73345fd212:
brcmfmac: Configure country code using device specific settings
prevents region codes from working on devices that lack a region code
translation table. In the event of an absent table, preserve the old
behaviour of using the provided code as-is.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Disable wireless power saving in the brcmfmac WLAN driver. This is a
temporary measure until the connectivity loss resulting from power
saving is resolved.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
This is a port of Pantelis Antoniou's v3 port that makes use of the
new upstreamed configfs support for binary attributes.
Original commit message:
Add a runtime interface to using configfs for generic device tree overlay
usage. With it its possible to use device tree overlays without having
to use a per-platform overlay manager.
Please see Documentation/devicetree/configfs-overlays.txt for more info.
Changes since v2:
- Removed ifdef CONFIG_OF_OVERLAY (since for now it's required)
- Created a documentation entry
- Slight rewording in Kconfig
Changes since v1:
- of_resolve() -> of_resolve_phandles().
Originally-signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
DT configfs: Fix build errors on other platforms
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
DT configfs: fix build error
There is an error when compiling rpi-4.6.y branch:
CC drivers/of/configfs.o
drivers/of/configfs.c:291:21: error: initialization from incompatible pointer type [-Werror=incompatible-pointer-types]
.default_groups = of_cfs_def_groups,
^
drivers/of/configfs.c:291:21: note: (near initialization for 'of_cfs_subsys.su_group.default_groups.next')
The .default_groups is linked list since commit
1ae1602de0.
This commit uses configfs_add_default_group to fix this problem.
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Add non-mainline source for rtl8192cu wireless driver version v4.0.2_9000 as
this is widely used. Disable older rtlwifi driver.
8192cu needs old wireless extensions
The obsolete WIRELESS_EXT configuration is used
by the old Realtek code and is needed for AP support.
8192cu: CONFIG_AP_MODE hardcoded in autoconf.h
rtl8192c_rf6052: PHY_RFShadowRefresh(): fix off-by-one
Signed-off-by: Marc Kleine-Budde <mkl@blackshift.org>
rtl8192cu: Add PID for D-Link DWA 131
The pl011 driver looks for DT aliases of the form "serial<n>",
and if found uses <n> as the device ID. This can cause
/dev/ttyAMA0 to become /dev/ttyAMA1, which is confusing if the
other serial port is provided by the 8250 driver which doesn't
use the same logic.
Add a mailbox-driven backlight controller for the Raspberry Pi DSI
touchscreen display. Requires updated GPU firmware to recognise the
mailbox request.
Signed-off-by: Gordon Hollingworth <gordon@raspberrypi.org>
commit cf5ef3a299 upstream.
This patch adds 32 bit word capability to the wm8731 driver. The wm8731
codec is capable of handling 32 bit word sizes, however that has not
previously been activated in the codec driver.
Signed-off-by: Matt Flax <flatmax@flatmax.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Support IQAudIO Digi board with iqaudio_digi machine driver and
iqaudio-digi-wm8804-audio overlay.
NB. Machine driver is a cut and paste of hifiberry_digi code, with format
and general cleanup to comply with kernel coding standards.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
Contains the sound/soc/bcm ALSA machine driver and necessary alterations to the Kconfig and Makefile.
Adds the dts overlay and updates the Makefile and README.
Updates the relevant defconfig files to enable building for the Raspberry Pi.
Thanks to Phil Elwell (pelwell) for the review, simple-card concepts and discussion. Thanks to Clive Messer for overlay naming suggestions.
Added support for headphones, microphone and bclk_ratio settings.
This patch adds headphone and microphone capability to the Audio Injector sound card. The patch also sets the bit clock ratio for use in the bcm2835-i2s driver. The bcm2835-i2s can't handle an 8 kHz sample rate when the bit clock is at 12 MHz because its register is only 10 bits wide which can't represent the ch2 offset of 1508. For that reason, the rate constraint is added.
This commit adds basic support for the codec usage including: Device tree overlay,
binding I2S bus and setting I2S mode, clock source and frequency setting according
to spec.
Signed-off-by: Andrey Grodzovsky <andrey2805@gmail.com>
justboom-dac: Adjust for ALSA API change
As of 4.4, snd_soc_limit_volume now takes a struct snd_soc_card *
rather than a struct snd_soc_codec *.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Jan Grulich <jan@grulich.eu>
config: fix RaspiDAC Rev.3x dependencies
Change depends to SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S
like the other I2S soundcard drivers.
Signed-off-by: Matthias Reichl <hias@horus.com>
The driver contains a low-level hardware driver for the TAS5713 and the
drivers for the Raspberry Pi I2S subsystem.
TAS5713: return error if initialisation fails
Existing TAS5713 driver logs errors during initialisation, but does not return
an error code. Therefore even if initialisation fails, the driver will still be
loaded, but won't work. This patch fixes this. I2C communication error will now
reported correctly by a non-zero return code.
HiFiBerry Amp: fix device-tree problems
Some code to load the driver based on device-tree-overlays was missing. This is added by this patch.
The driver is based on the HiFiBerry DAC driver. However HiFiBerry DAC+ uses
a different codec chip (PCM5122), therefore a new driver is necessary.
Add support for the HiFiBerry DAC+ Pro.
The HiFiBerry DAC+ and DAC+ Pro products both use the existing bcm sound driver with the DAC+ Pro having a special clock device driver representing the two high precision oscillators.
An addition bug fix is included for the PCM512x codec where by the physical size of the sample frame is used in the calculation of the LRCK divisor as it was found to be wrong when using 24-bit depth sample contained in a little endian 4-byte sample frame.
Limit PCM512x "Digital" gain to 0dB by default with HiFiBerry DAC+
24db_digital_gain DT param can be used to specify that PCM512x
codec "Digital" volume control should not be limited to 0dB gain,
and if specified will allow the full 24dB gain.
Add dt param to force HiFiBerry DAC+ Pro into slave mode
"dtoverlay=hifiberry-dacplus,slave"
Add 'slave' param to use HiFiBerry DAC+ Pro in slave mode,
with Pi as master for bit and frame clock.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
Set a limit of 0dB on Digital Volume Control
The main volume control in the PCM512x DAC has a range up to
+24dB. This is dangerously loud and can potentially cause massive
clipping in the output stages. Therefore this sets a sensible
limit of 0dB for this control.
Allow up to 24dB digital gain to be applied when using IQAudIO DAC+
24db_digital_gain DT param can be used to specify that PCM512x
codec "Digital" volume control should not be limited to 0dB gain,
and if specified will allow the full 24dB gain.
Modify IQAudIO DAC+ ASoC driver to set card/dai config from dt
Add the ability to set the card name, dai name and dai stream name, from
dt config.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
IQaudIO: auto-mute for AMP+ and DigiAMP+
IQAudIO amplifier mute via GPIO22. Add dt params for "one-shot" unmute
and auto mute.
Revision 2, auto mute implementing HiassofT suggestion to mute/unmute
using set_bias_level, rather than startup/shutdown....
"By default DAPM waits 5 seconds (pmdown_time) before shutting down
playback streams so a close/stop immediately followed by open/start
doesn't trigger an amp mute+unmute."
Tested on both AMP+ (via DAC+) and DigiAMP+, with both options...
dtoverlay=iqaudio-dacplus,unmute_amp
"one-shot" unmute when kernel module loads.
dtoverlay=iqaudio-dacplus,auto_mute_amp
Unmute amp when ALSA device opened by a client. Mute, with 5 second delay
when ALSA device closed. (Re-opening the device within the 5 second close
window, will cancel mute.)
Revision 4, using gpiod.
Revision 5, clean-up formatting before adding mute code.
- Convert tab plus 4 space formatting to 2x tab
- Remove '// NOT USED' commented code
Revision 6, don't attempt to "one-shot" unmute amp, unless card is
successfully registered.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
Signed-off-by: Daniel Matuschek <daniel@matuschek.net>
Add a parameter to turn off SPDIF output if no audio is playing
This patch adds the paramater auto_shutdown_output to the kernel module.
Default behaviour of the module is the same, but when auto_shutdown_output
is set to 1, the SPDIF oputput will shutdown if no stream is playing.
bugfix for 32kHz sample rate, was missing
HiFiBerry Digi: set SPDIF status bits for sample rate
The HiFiBerry Digi driver did not signal the sample rate in the SPDIF status bits.
While this is optional, some DACs and receivers do not accept this signal. This patch
adds the sample rate bits in the SPDIF status block.
This adds a machine driver for the HifiBerry DAC.
It is a sound card that can
be stacked onto the Raspberry Pi.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
The Raspberry Pi firmware manages the power-down and reboot
process. To do this it installs a pm_power_off handler, causing
the gpio-poweroff module to abort the probe function.
This patch introduces a "force" DT property that overrides that
behaviour, and also adds a DT overlay to enable and control it.
Note that running in an active-low configuration (DT parameter
"active_low") requires a custom dt-blob.bin and probably won't
allow a reboot without switching off, so an external inversion
of the trigger signal may be preferable.
Provide a __copy_from_user that uses memcpy. On BCM2708, use
optimised memcpy/memmove/memcmp/memset implementations.
arch/arm: Add mmiocpy/set aliases for memcpy/set
See: https://github.com/raspberrypi/linux/issues/1082
copy_from_user: CPU_SW_DOMAIN_PAN compatibility
The downstream copy_from_user acceleration must also play nice with
CONFIG_CPU_SW_DOMAIN_PAN.
See: https://github.com/raspberrypi/linux/issues/1381
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
1-wire: Add support for configuring pin for w1-gpio kernel module
See: https://github.com/raspberrypi/linux/pull/457
Add bitbanging pullups, use them for w1-gpio
Allows parasite power to work, uses module option pullup=1
bcm2708: Ensure 1-wire pullup is disabled by default, and expose as module parameter
Signed-off-by: Alex J Lennon <ajlennon@dynamicdevices.co.uk>
w1-gpio: Add gpiopin module parameter and correctly free up gpio pull-up pin, if set
Signed-off-by: Alex J Lennon <ajlennon@dynamicdevices.co.uk>
w1-gpio: Sort out the pullup/parasitic power tangle
Especially on platforms with a slower CPU but a relatively high
framebuffer fill bandwidth, like current ARM devices, the existing
console monochrome imageblit function used to draw console text is
suboptimal for common pixel depths such as 16bpp and 32bpp. The existing
code is quite general and can deal with several pixel depths. By creating
special case functions for 16bpp and 32bpp, by far the most common pixel
formats used on modern systems, a significant speed-up is attained
which can be readily felt on ARM-based devices like the Raspberry Pi
and the Allwinner platform, but should help any platform using the
fb layer.
The special case functions allow constant folding, eliminating a number
of instructions including divide operations, and allow the use of an
unrolled loop, eliminating instructions with a variable shift size,
reducing source memory access instructions, and eliminating excessive
branching. These unrolled loops also allow much better code optimization
by the C compiler. The code that selects which optimized variant is used
is also simplified, eliminating integer divide instructions.
The speed-up, measured by timing 'cat file.txt' in the console, varies
between 40% and 70%, when testing on the Raspberry Pi and Allwinner
ARM-based platforms, depending on font size and the pixel depth, with
the greater benefit for 32bpp.
Signed-off-by: Harm Hanemaaijer <fgenfb@yahoo.com>
Based on the patch authored by Ali Gholami Rudi at
https://lkml.org/lkml/2009/7/13/153
Provide an ioctl for userspace applications, but only if this operation
is hardware accelerated (otherwide it does not make any sense).
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
The "input" trigger makes the associated GPIO an input. This is to support
the Raspberry Pi PWR LED, which is driven by external hardware in normal use.
N.B. pwr_led is not available on Model A or B boards.
leds-gpio: Implement the brightness_get method
The power LED uses some clever logic that means it is driven
by a voltage measuring circuit when configured as input, otherwise
it is driven by the GPIO output value. This patch wires up the
brightness_get method for leds-gpio so that user-space can monitor
the LED value via /sys/class/gpio/led1/brightness. Using the input
trigger this returns an indication of the system power health,
otherwise it is just whatever value the trigger has written most
recently.
See: https://github.com/raspberrypi/linux/issues/1064
The EPAPR standard says to use "phandle" properties to store phandles,
rather than the deprecated "linux,phandle" version. By default, dtc
generates both, but adding "-H epapr" causes it to only generate
"phandle"s, saving some space and clutter.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Change the filenames and extensions to keep the pre-DDT style of
overlay (<name>-overlay.dtb) distinct from new ones that use a
different style of local fixups (<name>.dtbo), and to match other
platforms.
The RPi firmware uses the DDTK trailer atom to choose which type of
overlay to use for each kernel.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Add the bare minimum needed to boot BCM2708 from a Device Tree.
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
BCM2708: DT: change 'axi' nodename to 'soc'
Change DT node named 'axi' to 'soc' so it matches ARCH_BCM2835.
The VC4 bootloader fills in certain properties in the 'axi' subtree,
but since this is part of an upstreaming effort, the name is changed.
Signed-off-by: Noralf Tronnes notro@tronnes.org
BCM2708_DT: Correct length of the peripheral space
Use dts-dirs feature for overlays.
The kernel makefiles have a dts-dirs target that is for vendor subdirectories.
Using this fixes the install_dtbs target, which previously did not install the overlays.
BCM270X_DT: configure I2S DMA channels
Signed-off-by: Matthias Reichl <hias@horus.com>
BCM270X_DT: switch to bcm2835-i2s
I2S soundcard drivers with proper devicetree support (i.e. not linking
to the cpu_dai/platform via name but to cpu/platform via of_node)
will work out of the box without any modifications.
When the kernel is compiled without devicetree support the platform
code will instantiate the bcm2708-i2s driver and I2S soundcard drivers
will link to it via name, as before.
Signed-off-by: Matthias Reichl <hias@horus.com>
SDIO-overlay: add poll_once-boolean parameter
Add paramter to toggle sdio-device-polling
done every second or once at boot-time.
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
BCM270X_DT: Make mmc overlay compatible with current firmware
The original DT overlay logic followed a merge-then-patch procedure,
i.e. parameters are applied to the loaded overlay before the overlay
is merged into the base DTB. This sequence has been changed to
patch-then-merge, in order to support parameterised node names, and
to protect against bad overlays. As a result, overrides (parameters)
must only target labels in the overlay, but the overlay can obviously target nodes in the base DTB.
mmc-overlay.dts (that switches back to the original mmc sdcard
driver) is the only overlay violating that rule, and this patch
fixes it.
bcm270x_dt: Use the sdhost MMC controller by default
The "mmc" overlay reverts to using the other controller.
squash: Add cprman to dt
BCM270X_DT: Use clk_core for I2C interfaces
Includes the new localfixups format.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
scripts/dtc: Fix UMR causing corrupt dtbo overlay files
struct fixup_entry is allocated from the heap but it's member
local_fixup_generated was never initialized. This lead to
corrupted dtbo files.
Fix this by initializing local_fixup_generated to false.
Signed-off-by: Matthias Reichl <hias@horus.com>
scripts/dtc: Only emit local fixups for overlays
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The Raspberry Pi firmware looks for a trailer on the kernel image to
determine whether it was compiled with Device Tree support enabled.
If the firmware finds a kernel without this trailer, or which has a
trailer indicating that it isn't DT-capable, it disables DT support
and reverts to using ATAGs.
The mkknlimg utility adds that trailer, having first analysed the
image to look for signs of DT support and the kernel version string.
knlinfo displays the contents of the trailer in the given kernel image.
scripts/mkknlimg: Add support for ARCH_BCM2835
Add a new trailer field indicating whether this is an ARCH_BCM2835
build, as opposed to MACH_BCM2708/9. If the loader finds this flag
is set it changes the default base dtb file name from bcm270x...
to bcm283y...
Also update knlinfo to show the status of the field.
scripts/mkknlimg: Improve ARCH_BCM2835 detection
The board support code contains sufficient strings to be able to
distinguish 2708 vs. 2835 builds, so remove the check for
bcm2835-pm-wdt which could exist in either.
Also, since the canned configuration is no longer built in (it's
a module), remove the config string checking.
See: https://github.com/raspberrypi/linux/issues/1157
scripts: Multi-platform support for mkknlimg and knlinfo
The firmware uses tags in the kernel trailer to choose which dtb file
to load. Current firmware loads bcm2835-*.dtb if the '283x' tag is true,
otherwise it loads bcm270*.dtb. This scheme breaks if an image supports
multiple platforms.
This patch adds '270X' and '283X' tags to indicate support for RPi and
upstream platforms, respectively. '283x' (note lower case 'x') is left
for old firmware, and is only set if the image only supports upstream
builds.
scripts/mkknlimg: Append a trailer for all input
Now that the firmware assumes an unsigned kernel is DT-capable, it is
helpful to be able to mark a kernel as being non-DT-capable.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
scripts/knlinfo: Decode DDTK atom
Show the DDTK atom as being a boolean.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
- Supports raw YUV capture, preview, JPEG and H264.
- Uses videobuf2 for data transfer, using dma_buf.
- Uses 3.6.10 timestamping
- Camera power based on use
- Uses immutable input mode on video encoder
Signed-off-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Luke Diamand <luked@broadcom.com>
V4L2: Fixes from 6by9
V4L2: Fix EV values. Add manual shutter speed control
V4L2 EV values should be in units of 1/1000. Corrected.
Add support for V4L2_CID_EXPOSURE_ABSOLUTE which should
give manual shutter control. Requires manual exposure mode
to be selected first.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Correct JPEG Q-factor range
Should be 1-100, not 0-100
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Fix issue of driver jamming if STREAMON failed.
Fix issue where the driver was left in a partially enabled
state if STREAMON failed, and would then reject many IOCTLs
as it thought it was streaming.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Fix ISO controls.
Driver was passing the index to the GPU, and not the desired
ISO value.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Add flicker avoidance controls
Add support for V4L2_CID_POWER_LINE_FREQUENCY to set flicker
avoidance frequencies.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Add support for frame rate control.
Add support for frame rate (or time per frame as V4L2
inverts it) control via s_parm.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Improve G_FBUF handling so we pass conformance
Return some sane numbers for get framebuffer so that
we pass conformance.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Fix information advertised through g_vidfmt
Width and height were being stored based on incorrect
values.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Add support for inline H264 headers
Add support for V4L2_CID_MPEG_VIDEO_REPEAT_SEQ_HEADER
to control H264 inline headers.
Requires firmware fix to work correctly, otherwise format
has to be set to H264 before this parameter is set.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Fix JPEG timestamp issue
JPEG images were coming through from the GPU with timestamp
of 0. Detect this and give current system time instead
of some invalid value.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Fix issue when switching down JPEG resolution.
JPEG buffer size calculation is based on input resolution.
Input resolution was being configured after output port
format. Caused failures if switching from one JPEG resolution
to a smaller one.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Enable MJPEG encoding
Requires GPU firmware update to support MJPEG encoder.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Correct flag settings for compressed formats
Set flags field correctly on enum_fmt_vid_cap for compressed
image formats.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: H264 profile & level ctrls, FPS control and auto exp pri
Several control handling updates.
H264 profile and level controls.
Timeperframe/FPS reworked to add V4L2_CID_EXPOSURE_AUTO_PRIORITY to
select whether AE is allowed to override the framerate specified.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Correct BGR24 to RGB24 in format table
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Add additional pixel formats. Correct colourspace
Adds the other flavours of YUYV, and NV12.
Corrects the overlay advertised colourspace.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Drop logging msg from info to debug
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Initial pass at scene modes.
Only supports exposure mode and metering modes.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Add manual white balance control.
Adds support for V4L2_CID_RED_BALANCE and
V4L2_CID_BLUE_BALANCE. Only has an effect if
V4L2_CID_AUTO_N_PRESET_WHITE_BALANCE has
V4L2_WHITE_BALANCE_MANUAL selected.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
config: Enable V4L / MMAL driver
V4L2: Increase the MMAL timeout to 3sec
MJPEG codec flush is now taking longer and results
in a kernel panic if the driver has stopped waiting for
the result when it finally completes.
Increase the timeout value from 1 to 3secs.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Add support for setting H264_I_PERIOD
Adds support for the parameter V4L2_CID_MPEG_VIDEO_H264_I_PERIOD
to set the frequency with which I frames are produced.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Enable GPU function for removing padding from images.
GPU can now support arbitrary strides, although may require
additional processing to achieve it. Enable this feature
so that the images delivered are the size requested.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Add support for V4L2_PIX_FMT_BGR32
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Set the colourspace to avoid odd YUV-RGB conversions
Removes the amiguity from the conversion routines and stops
them dropping back to the SD vs HD choice of coeffs.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Make video/still threshold a run-time param
Move the define for at what resolution the driver
switches from a video mode capture to a stills mode
capture to module parameters.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Fix incorrect pool sizing
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Add option to disable enum_framesizes.
Gstreamer's handling of a driver that advertises
V4L2_FRMSIZE_TYPE_STEPWISE to define the supported
resolutions is broken. See bug
https://bugzilla.gnome.org/show_bug.cgi?id=726521
Optional parameter of gst_v4l2src_is_broken added.
If non-zero, the driver claims not to support that
ioctl, and gstreamer should be happy again (it
guesses a set of defaults for itself).
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Add support for more image formats
Adds YVU420 (YV12), YVU420SP (NV21), and BGR888.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Extend range for V4L2_CID_MPEG_VIDEO_H264_I_PERIOD
Request to extend the range from the fairly arbitrary
1000 frames (33 seconds at 30fps). Extend out to the
max range supported (int32 value).
Also allow 0, which is handled by the codec as only
send an I-frame on the first frame and never again.
There may be an exception if it detects a significant
scene change, but there's no easy way around that.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
bcm2835-camera: stop_streaming now has a void return
BCM2835-V4L2: Fix compliance test failures
VIDIOC_TRY_FMT and VIDIOC_S_FMT tests were faling due
to reporting V4L2_COLORSPACE_JPEG when the colour
format wasn't V4L2_PIX_FMT_JPEG.
Now reports V4L2_COLORSPACE_SMPTE170M for YUV formats.
bcm2835 camera planar/packed stride length
Added a field to the mmal_fmt struct used to compute the bytes per line
when using a particular format. This results in the correct stride being
calculated even when the format is planar.
Signed-off-by: Garrett Wilson <g@floft.net>
bcm2835: camera: check for scene not being found
static analysis by cppcheck detected some potential NULL pointer
dereference issues:
[drivers/media/platform/bcm2835/controls.c:854]: (error) Possible null
pointer dereference: scene
(and lines 858, 859 too)
it is possible that scene is not found because of an invalue ctrl->val
and is therefore NULL and hence causing a null pointer dereference.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
bcm2835: memcpy port data to m rather than rmsg
static analysis by cppcheck detected a memcpy to rmsg which is
not actually initialized at that point. The memcpy should be copying
to variable m instead.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
BCM2835-V4L2: Return buffers to videobuf2 on shutdown
https://github.com/raspberrypi/linux/issues/817
Fixes the kernel warning from videobuf2 as buffers
are now returned as they are being flushed on
stop_streaming.
squash: Fixup bcm2835-camera for changes in kernel 4.4 api
v4l2: Fix up driver to upstream timestamp changes
bcm2835-camera: fix a bug in computation of frame timestamp
Fixes#1318
V4L2 driver updates (#1393)
* BCM2835-V4L2: Correct ISO control and add V4L2_CID_ISO_SENSITIVITY_AUTO
https://github.com/raspberrypi/linux/issues/1251
V4L2_CID_ISO_SENSITIVITY was not advertising ISO*1000 as it should.
V4L2_CID_ISO_SENSITIVITY_AUTO was not implemented, so was taking
V4L2_CID_ISO_SENSITIVITY as 0 for auto mode.
Still accepts 0 for auto, but also abides by the new parameter.
Signed-off-by: Dave Stevenson <6by9@users.noreply.github.com>
* BCM2835-V4L2: Add a video_nr parameter.
Adds a kernel parameter "video_nr" to specify the preferred
/dev/videoX device node.
https://www.raspberrypi.org/forums/viewtopic.php?f=38&t=136120&p=905545
Signed-off-by: Dave Stevenson <6by9@users.noreply.github.com>
* BCM2835-V4L2: Add support for multiple cameras
Ask GPU on load how many cameras have been detected, and
enumerate that number of devices.
Only applicable on the Compute Module as no other device
exposes multiple CSI2 interfaces.
Signed-off-by: Dave Stevenson <6by9@users.noreply.github.com>
* BCM2835-V4L2: Add control of the overlay location and alpha.
Actually do something useful in vidioc_s_fmt_vid_overlay and
vidioc_try_fmt_vid_overlay, rather than effectively having
read-only fields.
Signed-off-by: Dave Stevenson <6by9@users.noreply.github.com>
* BCM2835-V4L2: V4L2-Compliance failure fix
VIDIOC_TRY_FMT was failing due to bytesperline not
being set correctly by default.
Signed-off-by: Dave Stevenson <6by9@users.noreply.github.com>
* BCM2835-V4L2: Make all module parameters static
Clean up to correct variable scope
Signed-off-by: Dave Stevenson <6by9@users.noreply.github.com>
V4L2: Request maximum resolution from GPU
Get resolution information about the sensors from the GPU
and advertise it correctly.
Signed-off-by: Dave Stevenson <6by9@users.noreply.github.com>
BCM2835-V4L2: Increase minimum resolution to 32x32
https://github.com/raspberrypi/linux/issues/1498 showed
up that 16x16 is failing to work on the GPU for some reason.
GPU bug being tracked on
https://github.com/raspberrypi/firmware/issues/607
Workaround here by increasing minimum resolution via V4L2
to 32x32.
Signed-off-by: Dave Stevenson <6by9@users.noreply.github.com>
[media]: bcm2835-camera: fix compilation error
There is an error when compiling rpi-4.6.y branch:
CC [M] drivers/media/platform/bcm2835/bcm2835-camera.o
drivers/media/platform/bcm2835/bcm2835-camera.c:639:17: error: initialization from incompatible pointer type [-Werror=incompatible-pointer-types]
.queue_setup = queue_setup,
^
drivers/media/platform/bcm2835/bcm2835-camera.c:639:17: note: (near initialization for 'bm2835_mmal_video_qops.queue_setup')
The const void *parg in setup_queue callback is not needed since commit:
df9ecb0cad.
This commit removes it.
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
bcm2835-camera: Fix max/min error when looping over cameras/resolutions
See: https://github.com/raspberrypi/linux/issues/1447#issuecomment-221303506
BCM2835-V4L2: Correct handling for BGR24 vs RGB24.
There was a bug in the GPU firmware that had reversed these
two formats.
Detect the old firmware, and reverse the formats if necessary.
Signed-off-by: Dave Stevenson <6by9@users.noreply.github.com>
Support booting without Device Tree.
Turn on USB power.
Load driver early because of lacking support for deferred probing
in many drivers.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Add module for accessing the mailbox property channel through
/dev/vcio. Was previously in bcm2708-vcio.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
i2c-bcm2708: fixed baudrate
Fixed issue where the wrong CDIV value was set for baudrates below 3815 Hz (for 250MHz bus clock).
In that case the computed CDIV value was more than 0xffff. However the CDIV register width is only 16 bits.
This resulted in incorrect setting of CDIV and higher baudrate than intended.
Example: 3500Hz -> CDIV=0x11704 -> CDIV(16bit)=0x1704 -> 42430Hz
After correction: 3500Hz -> CDIV=0x11704 -> CDIV(16bit)=0xffff -> 3815Hz
The correct baudrate is shown in the log after the cdiv > 0xffff correction.
Perform I2C combined transactions when possible
Perform I2C combined transactions whenever possible, within the
restrictions of the Broadcomm Serial Controller.
Disable DONE interrupt during TA poll
Prevent interrupt from being triggered if poll is missed and transfer
starts and finishes.
i2c: Make combined transactions optional and disabled by default
i2c: bcm2708: add device tree support
Add DT support to driver and add to .dtsi file.
Setup pins in .dts file.
i2c is disabled by default.
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
bcm2708: don't register i2c controllers when using DT
The devices for the i2c controllers are in the Device Tree.
Only register devices when not using DT.
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
I2C: Only register the I2C device for the current board revision
i2c_bcm2708: Fix clock reference counting
Fix grabbing lock from atomic context in i2c driver
2 main changes:
- check for timeouts in the bcm2708_bsc_setup function as indicated by this comment:
/* poll for transfer start bit (should only take 1-20 polls) */
This implies that the setup function can now fail so account for this everywhere it's called
- Removed the clk_get_rate call from inside the setup function as it locks a mutex and that's not ok since we call it from under a spin lock.
i2c-bcm2708: When using DT, leave the GPIO setup to pinctrl
i2c-bcm2708: Increase timeouts to allow larger transfers
Use the timeout value provided by the I2C_TIMEOUT ioctl when waiting
for completion. The default timeout is 1 second.
See: https://github.com/raspberrypi/linux/issues/260
i2c-bcm2708/BCM270X_DT: Add support for I2C2
The third I2C bus (I2C2) is normally reserved for HDMI use. Careless
use of this bus can break an attached display - use with caution.
It is recommended to disable accesses by VideoCore by setting
hdmi_ignore_edid=1 or hdmi_edid_file=1 in config.txt.
The interface is disabled by default - enable using the
i2c2_iknowwhatimdoing DT parameter.
bcm2708-spi: Don't use static pin configuration with DT
Also remove superfluous error checking - the SPI framework ensures the
validity of the chip_select value.
i2c-bcm2708: Remove non-DT support
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Set the BSC_CLKT clock streching timeout to 35ms as per SMBus specs.
BCM270x: Move thermal sensor to Device Tree
Add Device Tree support to bcm2835-thermal driver.
Add thermal sensor device to Device Tree.
Don't add platform device when booting in DT mode.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
lirc_rpi: Use read_current_timer to determine transmitter delay. Thanks to jjmz and others
See: https://github.com/raspberrypi/linux/issues/525
lirc: Remove restriction on gpio pins that can be used with lirc
Compute Module, for example could use different pins
lirc_rpi: Add parameter to specify input pin pull
Depending on the connected IR circuitry it might be desirable to change the
gpios internal pull from it pull-down default behaviour. Add a module
parameter to allow the user to set it explicitly.
Signed-off-by: Julian Scheel <julian@jusst.de>
lirc-rpi: Use the higher-level irq control functions
This module used to access the irq_chip methods of the
gpio controller directly, rather than going through the
standard enable_irq/irq_set_irq_type functions. This
caused problems on pinctrl-bcm2835 which only implements
the irq_enable/disable methods and not irq_unmask/mask.
lirc-rpi: Correct the interrupt usage
1) Correct the use of enable_irq (i.e. don't call it so often)
2) Correct the shutdown sequence.
3) Avoid a bcm2708_gpio driver quirk by setting the irq flags earlier
lirc-rpi: use getnstimeofday instead of read_current_timer
read_current_timer isn't guaranteed to return values in
microseconds, and indeed it doesn't on a Pi2.
Issue: linux#827
lirc-rpi: Add device tree support, and a suitable overlay
The overlay supports DT parameters that match the old module
parameters, except that gpio_in_pull should be set using the
strings "up", "down" or "off".
lirc-rpi: Also support pinctrl-bcm2835 in non-DT mode
fix auto-sense in lirc_rpi driver
On a Raspberry Pi 2, the lirc_rpi driver might receive spurious
interrupts and change it's low-active / high-active setting.
When this happens, the IR remote control stops working.
This patch disables this auto-detection if the 'sense' parameter
was set in the device tree, making the driver robust to such
spurious interrupts.
Add experimental support for the VideoCore shared memory service.
This allows user processes to allocate memory from VideoCore's
GPU relocatable heap and mmap the buffers. Additionally, the memory
handles can passed to other VideoCore services such as MMAL, OpenMax
and DispmanX
TODO
* This driver was originally released for BCM28155 which has a different
cache architecture to BCM2835. Consequently, in this release only
uncached mappings are supported. However, there's no fundamental
reason which cached mappings cannot be support or BCM2835
* More refactoring is required to remove the typedefs.
* Re-enable the some of the commented out debug-fs statistics which were
disabled when migrating code from proc-fs.
* There's a lot of code to support sharing of VCSM in order to support
Android. This could probably done more cleanly or perhaps just
removed.
Signed-off-by: Tim Gover <timgover@gmail.com>
config: Disable VC_SM for now to fix hang with cutdown kernel
vcsm: Use boolean as it cannot be built as module
On building the bcm_vc_sm as a module we get the following error:
v7_dma_flush_range and do_munmap are undefined in vc-sm.ko.
Fix by making it not an option to build as module
vcsm: Add ioctl for custom cache flushing
vc-sm: Move headers out of arch directory
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: popcornmix <popcornmix@gmail.com>
BCM270x: Move vc_mem
Make the vc_mem module available for ARCH_BCM2835 by moving it.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: popcornmix <popcornmix@gmail.com>
vchiq: create_pagelist copes with vmalloc memory
Signed-off-by: Daniel Stone <daniels@collabora.com>
vchiq: fix the shim message release
Signed-off-by: Daniel Stone <daniels@collabora.com>
vchiq: export additional symbols
Signed-off-by: Daniel Stone <daniels@collabora.com>
VCHIQ: Make service closure fully synchronous (drv)
This is one half of a two-part patch, the other half of which is to
the vchiq_lib user library. With these patches, calls to
vchiq_close_service and vchiq_remove_service won't return until any
associated callbacks have been delivered to the callback thread.
VCHIQ: Add per-service tracing
The new service option VCHIQ_SERVICE_OPTION_TRACE is a boolean that
toggles tracing for the specified service.
This commit also introduces vchi_service_set_option and the associated
option VCHI_SERVICE_OPTION_TRACE.
vchiq: Make the synchronous-CLOSE logic more tolerant
vchiq: Move logging control into debugfs
vchiq: Take care of a corner case tickled by VCSM
Closing a connection that isn't fully open requires care, since one
side does not know the other side's port number. Code was present to
handle the case where a CLOSE is sent immediately after an OPEN, i.e.
before the OPENACK has been received, but this was incorrectly being
used when an OPEN from a client using port 0 was rejected.
(In the observed failure, the host was attempting to use the VCSM
service, which isn't present in the 'cutdown' firmware. The failure
was intermittent because sometimes the keepalive service would
grab port 0.)
This case can be distinguished because the client's remoteport will
still be VCHIQ_PORT_FREE, and the srvstate will be OPENING. Either
condition is sufficient to differentiate it from the special case
described above.
vchiq: Avoid high load when blocked and unkillable
vchiq: Include SIGSTOP and SIGCONT in list of signals not-masked by vchiq to allow gdb to work
vchiq_arm: Complete support for SYNCHRONOUS mode
vchiq: Remove inline from suspend/resume
vchiq: Allocation does not need to be atomic
vchiq: Fix wrong condition check
The log level is checked from within the log call. Remove the check in the call.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
BCM270x: Add vchiq device to platform file and Device Tree
Prepare to turn the vchiq module into a driver.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2708: vchiq: Add Device Tree support
Turn vchiq into a driver and stop hardcoding resources.
Use devm_* functions in probe path to simplify cleanup.
A global variable is used to hold the register address. This is done
to keep this patch as small as possible.
Also make available on ARCH_BCM2835.
Based on work by Lubomir Rintel.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
vchiq: Change logging level for inbound data
vchiq_arm: Two cacheing fixes
1) Make fragment size vary with cache line size
Without this patch, non-cache-line-aligned transfers may corrupt
(or be corrupted by) adjacent data structures.
Both ARM and VC need to be updated to enable this feature. This is
ensured by having the loader apply a new DT parameter -
cache-line-size. The existence of this parameter guarantees that the
kernel is capable, and the parameter will only be modified from the
safe default if the loader is capable.
2) Flush/invalidate vmalloc'd memory, and invalidate after reads
vchiq: fix NULL pointer dereference when closing driver
The following code run as root will cause a null pointer dereference oops:
int fd = open("/dev/vc-cma", O_RDONLY);
if (fd < 0)
err(1, "open failed");
(void)close(fd);
[ 1704.877721] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[ 1704.877725] pgd = b899c000
[ 1704.877736] [00000000] *pgd=37fab831, *pte=00000000, *ppte=00000000
[ 1704.877748] Internal error: Oops: 817 [#1] PREEMPT SMP ARM
[ 1704.877765] Modules linked in: evdev i2c_bcm2708 uio_pdrv_genirq uio
[ 1704.877774] CPU: 2 PID: 3656 Comm: stress-ng-fstat Not tainted 3.19.1-12-generic-bcm2709 #12-Ubuntu
[ 1704.877777] Hardware name: BCM2709
[ 1704.877783] task: b8ab9b00 ti: b7e68000 task.ti: b7e68000
[ 1704.877798] PC is at __down_interruptible+0x50/0xec
[ 1704.877806] LR is at down_interruptible+0x5c/0x68
[ 1704.877813] pc : [<80630ee8>] lr : [<800704b0>] psr: 60080093
sp : b7e69e50 ip : b7e69e88 fp : b7e69e84
[ 1704.877817] r10: b88123c8 r9 : 00000010 r8 : 00000001
[ 1704.877822] r7 : b8ab9b00 r6 : 7fffffff r5 : 80a1cc34 r4 : 80a1cc34
[ 1704.877826] r3 : b7e69e50 r2 : 00000000 r1 : 00000000 r0 : 80a1cc34
[ 1704.877833] Flags: nZCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment user
[ 1704.877838] Control: 10c5387d Table: 3899c06a DAC: 00000015
[ 1704.877843] Process do-oops (pid: 3656, stack limit = 0xb7e68238)
[ 1704.877848] Stack: (0xb7e69e50 to 0xb7e6a000)
[ 1704.877856] 9e40: 80a1cc3c 00000000 00000010 b88123c8
[ 1704.877865] 9e60: b7e69e84 80a1cc34 fff9fee9 ffffffff b7e68000 00000009 b7e69ea4 b7e69e88
[ 1704.877874] 9e80: 800704b0 80630ea4 fff9fee9 60080013 80a1cc28 fff9fee9 b7e69edc b7e69ea8
[ 1704.877884] 9ea0: 8040f558 80070460 fff9fee9 ffffffff 00000000 00000000 00000009 80a1cb7c
[ 1704.877893] 9ec0: 00000000 80a1cb7c 00000000 00000010 b7e69ef4 b7e69ee0 803e1ba4 8040f514
[ 1704.877902] 9ee0: 00000e48 80a1cb7c b7e69f14 b7e69ef8 803e1c9c 803e1b74 b88123c0 b92acb18
[ 1704.877911] 9f00: b8812790 b8d815d8 b7e69f24 b7e69f18 803e2250 803e1bc8 b7e69f5c b7e69f28
[ 1704.877921] 9f20: 80167bac 803e222c 00000000 00000000 b7e69f54 b8ab9ffc 00000000 8098c794
[ 1704.877930] 9f40: b8ab9b00 8000efc4 b7e68000 00000000 b7e69f6c b7e69f60 80167d6c 80167b28
[ 1704.877939] 9f60: b7e69f8c b7e69f70 80047d38 80167d60 b7e68000 b7e68010 8000efc4 b7e69fb0
[ 1704.877949] 9f80: b7e69fac b7e69f90 80012820 80047c84 01155490 011549a8 00000001 00000006
[ 1704.877957] 9fa0: 00000000 b7e69fb0 8000ee5c 80012790 00000000 353d8c0f 7efc4308 00000000
[ 1704.877966] 9fc0: 01155490 011549a8 00000001 00000006 00000000 00000000 76cf3ba0 00000003
[ 1704.877975] 9fe0: 00000000 7efc42e4 0002272f 76e2ed66 60080030 00000003 00000000 00000000
[ 1704.877998] [<80630ee8>] (__down_interruptible) from [<800704b0>] (down_interruptible+0x5c/0x68)
[ 1704.878015] [<800704b0>] (down_interruptible) from [<8040f558>] (vchiu_queue_push+0x50/0xd8)
[ 1704.878032] [<8040f558>] (vchiu_queue_push) from [<803e1ba4>] (send_worker_msg+0x3c/0x54)
[ 1704.878045] [<803e1ba4>] (send_worker_msg) from [<803e1c9c>] (vc_cma_set_reserve+0xe0/0x1c4)
[ 1704.878057] [<803e1c9c>] (vc_cma_set_reserve) from [<803e2250>] (vc_cma_release+0x30/0x38)
[ 1704.878069] [<803e2250>] (vc_cma_release) from [<80167bac>] (__fput+0x90/0x1e0)
[ 1704.878082] [<80167bac>] (__fput) from [<80167d6c>] (____fput+0x18/0x1c)
[ 1704.878094] [<80167d6c>] (____fput) from [<80047d38>] (task_work_run+0xc0/0xf8)
[ 1704.878109] [<80047d38>] (task_work_run) from [<80012820>] (do_work_pending+0x9c/0xc4)
[ 1704.878123] [<80012820>] (do_work_pending) from [<8000ee5c>] (work_pending+0xc/0x20)
[ 1704.878133] Code: e50b1034 e3a01000 e50b2030 e580300c (e5823000)
..the fix is to ensure that we have actually initialized the queue before we attempt
to push any items onto it. This occurs if we do an open() followed by a close() without
any activity in between.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
vchiq_arm: Sort out the vmalloc case
See: https://github.com/raspberrypi/linux/issues/1055
vchiq: hack: Add include depecated dma include file
vchiq_arm: Tweak the logging output
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
vchiq_arm: Access the dequeue_pending flag locked
Reading through this code looking for another problem (now found in userland)
the use of dequeue_pending outside a lock didn't seem safe.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
vchiq_arm: Service callbacks must not fail
Service callbacks are not allowed to return an error. The internal callback
that delivers events and messages to user tasks does not enqueue them if
the service is closing, but this is not an error and should not be
reported as such.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
vchiq_arm: do not use page_cache_release(page) macro (#1403)
This macro is gone since 1fa64f198b.
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
vchiq: Upate to match get_user_pages prototype
vchiq_arm: Add completion records under the mutex
An issue was observed when flushing openmax components
which generate a large number of messages returning
buffers to host.
We occasionally found a duplicate message from 16
messages prior, resulting in a buffer returned twice.
While only one thread adds completions, without the
mutex you don't get the protection of the automatic
memory barrier you get with synchronisation objects.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: popcornmix <popcornmix@gmail.com>
alsa: add mmap support and some cleanups to bcm2835 ALSA driver
snd-bcm2835: Add support for spdif/hdmi passthrough
This adds a dedicated subdevice which can be used for passthrough of non-audio
formats (ie encoded a52) through the hdmi audio link. In addition to this
driver extension an appropriate card config is required to make alsa-lib
support the AES parameters for this device.
snd-bcm2708: Add mutex, improve logging
Fix for ALSA driver crash
Avoids an issue when closing and opening vchiq where a message can arrive before service handle has been written
alsa: reduce severity of expected warning message
snd-bcm2708: Fix dmesg spam for non-error case
alsa: Ensure mutexes are released through error paths
alsa: Make interrupted close paths quieter
BCM270x: Add onboard sound device to Device Tree
Add Device Tree support to alsa driver.
Add device to Device Tree.
Don't add platform devices when booting in DT mode.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2835: access controls under the audio mutex
I don't think the ALSA framework provides any kind of automatic
synchronization within the control callbacks. We most likely need
to ensure this manually, so add locking around all access to shared
mutable data. In particular, bcm2835_audio_set_ctls() should
probably always be called under our own audio lock.
Signed-off-by: popcornmix <popcornmix@gmail.com>
vc_cma: Make the vc_cma area the default contiguous DMA area
vc_cma: Provide empty functions when module is not built
Providing empty functions saves the users from guarding the
function call with an #if clause.
Move __init markings from prototypes to functions.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Some SD cards have been found that corrupt data when small blocks
are erased. Add a quirk to indicate that ERASE should not be used,
and set it for cards of that type.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
mmc: Apply QUIRK_BROKEN_ERASE to other capacities
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
mmc: Add card_quirks module parameter, log quirks
Use mmc_block.card_quirks to override the quirks for all SD or MMC
cards. The value is a bitfield using the bit positions defined in
include/linux/mmc/card.h. If the module parameter is placed in the
kernel command line (or bootargs) stored on the card then, assuming the
device only has one SD card interface, the override effectively becomes
card-specific.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM2835 has two SD card interfaces. This driver uses the other one.
bcm2835-sdhost: Error handling fix, and code clarification
bcm2835-sdhost: Adding overclocking option
Allow a different clock speed to be substitued for a requested 50MHz.
This option is exposed using the "overclock_50" DT parameter.
Note that the sdhost interface is restricted to integer divisions of
core_freq, and the highest sensible option for a core_freq of 250MHz
is 84 (250/3 = 83.3MHz), the next being 125 (250/2) which is much too
high.
Use at your own risk.
bcm2835-sdhost: Round up the overclock, so 62 works for 62.5Mhz
Also only warn once for each overclock setting.
bcm2835-sdhost: Improve error handling and recovery
1) Expose the hw_reset method to the MMC framework, removing many
internal calls by the driver.
2) Reduce overclock setting on error.
3) Increase timeout to cope with high capacity cards.
4) Add properties and parameters to control pio_limit and debug.
5) Reduce messages at probe time.
bcm2835-sdhost: Further improve overclock back-off
bcm2835-sdhost: Clear HBLC for PIO mode
Also update pio_limit default in overlay README.
bcm2835-sdhost: Add the ERASE capability
See: https://github.com/raspberrypi/linux/issues/1076
bcm2835-sdhost: Ignore CRC7 for MMC CMD1
It seems that the sdhost interface returns CRC7 errors for CMD1,
which is the MMC-specific SEND_OP_COND. Returning these errors to
the MMC layer causes a downward spiral, but ignoring them seems
to be harmless.
bcm2835-mmc/sdhost: Remove ARCH_BCM2835 differences
The bcm2835-mmc driver (and -sdhost driver that copied from it)
contains code to handle SDIO interrupts in a threaded interrupt
handler rather than waking the MMC framework thread. The change
follows a patch from Russell King that adds the facility as the
preferred way of working.
However, the new code path is only present in ARCH_BCM2835
builds, which I have taken to be a way of testing the waters
rather than making the change across the board; I can't see
any technical reason why it wouldn't be enabled for MACH_BCM270X
builds. So this patch standardises on the ARCH_BCM2835 code,
removing the old code paths.
bcm2835-sdhost: Don't log timeout errors unless debug=1
The MMC card-discovery process generates timeouts. This is
expected behaviour, so reporting it to the user serves no purpose.
Suppress the reporting of timeout errors unless the debug flag
is on.
bcm2835-sdhost: Add workaround for odd behaviour on some cards
For reasons not understood, the sdhost driver fails when reading
sectors very near the end of some SD cards. The problem could
be related to the similar issue that reading the final sector
of any card as part of a multiple read never completes, and the
workaround is an extension of the mechanism introduced to solve
that problem which ensures those sectors are always read singly.
bcm2835-sdhost: Major revision
This is a significant revision of the bcm2835-sdhost driver. It
improves on the original in a number of ways:
1) Through the use of CMD23 for reads it appears to avoid problems
reading some sectors on certain high speed cards.
2) Better atomicity to prevent crashes.
3) Higher performance.
4) Activity logging included, for easier diagnosis in the event
of a problem.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Restore ATOMIC flag to PIO sg mapping
Allocation problems have been seen in a wireless driver, and
this is the only change which might have been responsible.
SQUASH: bcm2835-sdhost: Only claim one DMA channel
With both MMC controllers enabled there are few DMA channels left. The
bcm2835-sdhost driver only uses DMA in one direction at a time, so it
doesn't need to claim two channels.
See: https://github.com/raspberrypi/linux/issues/1327
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Workaround for "slow" sectors
Some cards have been seen to cause timeouts after certain sectors are
read. This workaround enforces a minimum delay between the stop after
reading one of those sectors and a subsequent data command.
Using CMD23 (SET_BLOCK_COUNT) avoids this problem, so good cards will
not be penalised by this workaround.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Firmware manages the clock divisor
The bcm2835-sdhost driver hands control of the CDIV clock divisor
register to matching firmware, allowing it to adjust to a changing
core clock. This removes the need to use the performance governor or
to enable io_is_busy on the on-demand governor in order to get the
best SD performance.
N.B. As SD clocks must be an integer divisor of the core clock, it is
possible that the SD clock for "turbo" mode can be different (even
lower) than "normal" mode.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Reset the clock in task context
Since reprogramming the clock can now involve a round-trip to the
firmware it must not be done at atomic context, and a tasklet
is not a task.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
mmc: Disable CMD23 transfers on all cards
Pending wire-level investigation of these types of transfers
and associated errors on bcm2835-mmc, disable for now. Fallback of
CMD18/CMD25 transfers will be used automatically by the MMC layer.
Reported/Tested-by: Gellert Weisz <gellert@raspberrypi.org>
mmc: bcm2835-mmc: enable DT support for all architectures
Both ARCH_BCM2835 and ARCH_BCM270x are built with OF now.
Enable Device Tree support for all architectures.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
mmc: bcm2835-mmc: fix probe error handling
Probe error handling is broken in several places.
Simplify error handling by using device managed functions.
Replace pr_{err,info} with dev_{err,info}.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2835-mmc: Add locks when accessing sdhost registers
bcm2835-mmc: Add range of debug options for slowing things down
bcm2835-mmc: Add option to disable some delays
bcm2835-mmc: Add option to disable MMC_QUIRK_BLK_NO_CMD23
bcm2835-mmc: Default to disabling MMC_QUIRK_BLK_NO_CMD23
bcm2835-mmc: Adding overclocking option
Allow a different clock speed to be substitued for a requested 50MHz.
This option is exposed using the "overclock_50" DT parameter.
Note that the mmc interface is restricted to EVEN integer divisions of
250MHz, and the highest sensible option is 63 (250/4 = 62.5), the
next being 125 (250/2) which is much too high.
Use at your own risk.
bcm2835-mmc: Round up the overclock, so 62 works for 62.5Mhz
Also only warn once for each overclock setting.
mmc: bcm2835-mmc: Make available on ARCH_BCM2835
Make the bcm2835-mmc driver available for use on ARCH_BCM2835.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270x_DT: add bcm2835-mmc entry
Add Device Tree entry for bcm2835-mmc.
In non-DT mode, don't add the device in the board file.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2835-mmc: Don't overwrite MMC capabilities from DT
bcm2835-mmc: Don't override bus width capabilities from devicetree
Take out the force setting of the MMC_CAP_4_BIT_DATA host capability
so that the result read from devicetree via mmc_of_parse() is
preserved.
bcm2835-mmc: Only claim one DMA channel
With both MMC controllers enabled there are few DMA channels left. The
bcm2835-mmc driver only uses DMA in one direction at a time, so it
doesn't need to claim two channels.
See: https://github.com/raspberrypi/linux/issues/1327
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Add support for DMA controller of BCM2708 as used in the Raspberry Pi.
Currently it only supports cyclic DMA.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
dmaengine: expand functionality by supporting scatter/gather transfers sdhci-bcm2708 and dma.c: fix for LITE channels
DMA: fix cyclic LITE length overflow bug
dmaengine: bcm2708: Remove chancnt affectations
Mirror bcm2835-dma.c commit 9eba5536a7:
chancnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: overwrite dreq only if it is not set
dreq is set when the DMA channel is fetched from Device Tree.
slave_id is set using dmaengine_slave_config().
Only overwrite dreq with slave_id if it is not set.
dreq/slave_id in the cyclic DMA case is not touched, because I don't
have hardware to test with.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: do device registration in the board file
Don't register the device in the driver. Do it in the board file.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: don't restrict DT support to ARCH_BCM2835
Both ARCH_BCM2835 and ARCH_BCM270x are built with OF now.
Add Device Tree support to the non ARCH_BCM2835 case.
Use the same driver name regardless of architecture.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270x_DT: add bcm2835-dma entry
Add Device Tree entry for bcm2835-dma.
The entry doesn't contain any resources since they are handled
by the arch/arm/mach-bcm270x/dma.c driver.
In non-DT mode, don't add the device in the board file.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2708-dmaengine: Add debug options
BCM270x: Add memory and irq resources to dmaengine device and DT
Prepare for merging of the legacy DMA API arch driver dma.c
with bcm2708-dmaengine by adding memory and irq resources both
to platform file device and Device Tree node.
Don't use BCM_DMAMAN_DRIVER_NAME so we don't have to include mach/dma.h
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: Merge with arch dma.c driver and disable dma.c
Merge the legacy DMA API driver with bcm2708-dmaengine.
This is done so we can use bcm2708_fb on ARCH_BCM2835 (mailbox
driver is also needed).
Changes to the dma.c code:
- Use BIT() macro.
- Cutdown some comments to one line.
- Add mutex to vc_dmaman and use this, since the dev lock is locked
during probing of the engine part.
- Add global g_dmaman variable since drvdata is used by the engine part.
- Restructure for readability:
vc_dmaman_chan_alloc()
vc_dmaman_chan_free()
bcm_dma_chan_free()
- Restructure bcm_dma_chan_alloc() to simplify error handling.
- Use device irq resources instead of hardcoded bcm_dma_irqs table.
- Remove dev_dmaman_register() and code it directly.
- Remove dev_dmaman_deregister() and code it directly.
- Simplify bcm_dmaman_probe() using devm_* functions.
- Get dmachans from DT if available.
- Keep 'dma.dmachans' module argument name for backwards compatibility.
Make it available on ARCH_BCM2835 as well.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: set residue_granularity field
bcm2708-dmaengine supports residue reporting at burst level
but didn't report this via the residue_granularity field.
Without this field set properly we get playback issues with I2S cards.
dmaengine: bcm2708-dmaengine: Fix memory leak when stopping a running transfer
bcm2708-dmaengine: Use more DMA channels (but not 12)
1) Only the bcm2708_fb drivers uses the legacy DMA API, and
it requires a BULK-capable channel, so all other types
(FAST, NORMAL and LITE) can be made available to the regular
DMA API.
2) DMA channels 11-14 share an interrupt. The driver can't
handle this, so don't use channels 12-14 (12 was used, probably
because it appears to have an interrupt, but in reality that
interrupt is for activity on ANY channel). This may explain
a lockup encountered when running out of DMA channels.
The combined effect of this patch is to leave 7 DMA channels
available + channel 0 for bcm2708_fb via the legacy API.
See: https://github.com/raspberrypi/linux/issues/1110https://github.com/raspberrypi/linux/issues/1108
dmaengine: bcm2708: Make legacy API available for bcm2835-dma
bcm2708_fb uses the legacy DMA API, so in order to start using
bcm2835-dma, bcm2835-dma has to support the legacy API. Make this
possible by exporting bcm_dmaman_probe() and bcm_dmaman_remove().
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: Change DT compatible string
Both bcm2835-dma and bcm2708-dmaengine have the same compatible string.
So change compatible to "brcm,bcm2708-dma".
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: Remove driver but keep legacy API
Dropping non-DT support means we don't need this driver,
but we still need the legacy DMA API.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: popcornmix <popcornmix@gmail.com>
bcm2708_fb : Implement blanking support using the mailbox property interface
bcm2708_fb: Add pan and vsync controls
bcm2708_fb: DMA acceleration for fb_copyarea
Based on http://www.raspberrypi.org/phpBB3/viewtopic.php?p=62425#p62425
Also used Simon's dmaer_master module as a reference for tweaking DMA
settings for better performance.
For now busylooping only. IRQ support might be added later.
With non-overclocked Raspberry Pi, the performance is ~360 MB/s
for simple copy or ~260 MB/s for two-pass copy (used when dragging
windows to the right).
In the case of using DMA channel 0, the performance improves
to ~440 MB/s.
For comparison, VFP optimized CPU copy can only do ~114 MB/s in
the same conditions (hindered by reading uncached source buffer).
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
bcm2708_fb: report number of dma copies
Add a counter (exported via debugfs) reporting the
number of dma copies that the framebuffer driver
has done, in order to help evaluate different
optimization strategies.
Signed-off-by: Luke Diamand <luked@broadcom.com>
bcm2708_fb: use IRQ for DMA copies
The copyarea ioctl() uses DMA to speed things along. This
was busy-waiting for completion. This change supports using
an interrupt instead for larger transfers. For small
transfers, busy-waiting is still likely to be faster.
Signed-off-by: Luke Diamand <luke@diamand.org>
bcm2708: Make ioctl logging quieter
video: fbdev: bcm2708_fb: Don't panic on error
No need to panic the kernel if the video driver fails.
Just print a message and return an error.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
fbdev: bcm2708_fb: Add ARCH_BCM2835 support
Add Device Tree support.
Pass the device to dma_alloc_coherent() in order to get the
correct bus address on ARCH_BCM2835.
Use the new DMA legacy API header file.
Including <mach/platform.h> is not necessary.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270x_DT: Add bcm2708-fb device
Add bcm2708-fb to Device Tree and don't add the
platform device when booting in DT mode.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: popcornmix <popcornmix@gmail.com>
usb: dwc: fix lockdep false positive
Signed-off-by: Kari Suvanto <karis79@gmail.com>
usb: dwc: fix inconsistent lock state
Signed-off-by: Kari Suvanto <karis79@gmail.com>
Add FIQ patch to dwc_otg driver. Enable with dwc_otg.fiq_fix_enable=1. Should give about 10% more ARM performance.
Thanks to Gordon and Costas
Avoid dynamic memory allocation for channel lock in USB driver. Thanks ddv2005.
Add NAK holdoff scheme. Enabled by default, disable with dwc_otg.nak_holdoff_enable=0. Thanks gsh
Make sure we wait for the reset to finish
dwc_otg: fix bug in dwc_otg_hcd.c resulting in silent kernel
memory corruption, escalating to OOPS under high USB load.
dwc_otg: Fix unsafe access of QTD during URB enqueue
In dwc_otg_hcd_urb_enqueue during qtd creation, it was possible that the
transaction could complete almost immediately after the qtd was assigned
to a host channel during URB enqueue, which meant the qtd pointer was no
longer valid having been completed and removed. Usually, this resulted in
an OOPS during URB submission. By predetermining whether transactions
need to be queued or not, this unsafe pointer access is avoided.
This bug was only evident on the Pi model A where a device was attached
that had no periodic endpoints (e.g. USB pendrive or some wlan devices).
dwc_otg: Fix incorrect URB allocation error handling
If the memory allocation for a dwc_otg_urb failed, the kernel would OOPS
because for some reason a member of the *unallocated* struct was set to
zero. Error handling changed to fail correctly.
dwc_otg: fix potential use-after-free case in interrupt handler
If a transaction had previously aborted, certain interrupts are
enabled to track error counts and reset where necessary. On IN
endpoints the host generates an ACK interrupt near-simultaneously
with completion of transfer. In the case where this transfer had
previously had an error, this results in a use-after-free on
the QTD memory space with a 1-byte length being overwritten to
0x00.
dwc_otg: add handling of SPLIT transaction data toggle errors
Previously a data toggle error on packets from a USB1.1 device behind
a TT would result in the Pi locking up as the driver never handled
the associated interrupt. Patch adds basic retry mechanism and
interrupt acknowledgement to cater for either a chance toggle error or
for devices that have a broken initial toggle state (FT8U232/FT232BM).
dwc_otg: implement tasklet for returning URBs to usbcore hcd layer
The dwc_otg driver interrupt handler for transfer completion will spend
a very long time with interrupts disabled when a URB is completed -
this is because usb_hcd_giveback_urb is called from within the handler
which for a USB device driver with complicated processing (e.g. webcam)
will take an exorbitant amount of time to complete. This results in
missed completion interrupts for other USB packets which lead to them
being dropped due to microframe overruns.
This patch splits returning the URB to the usb hcd layer into a
high-priority tasklet. This will have most benefit for isochronous IN
transfers but will also have incidental benefit where multiple periodic
devices are active at once.
dwc_otg: fix NAK holdoff and allow on split transactions only
This corrects a bug where if a single active non-periodic endpoint
had at least one transaction in its qh, on frnum == MAX_FRNUM the qh
would get skipped and never get queued again. This would result in
a silent device until error detection (automatic or otherwise) would
either reset the device or flush and requeue the URBs.
Additionally the NAK holdoff was enabled for all transactions - this
would potentially stall a HS endpoint for 1ms if a previous error state
enabled this interrupt and the next response was a NAK. Fix so that
only split transactions get held off.
dwc_otg: Call usb_hcd_unlink_urb_from_ep with lock held in completion handler
usb_hcd_unlink_urb_from_ep must be called with the HCD lock held. Calling it
asynchronously in the tasklet was not safe (regression in
c4564d4a1a).
This change unlinks it from the endpoint prior to queueing it for handling in
the tasklet, and also adds a check to ensure the urb is OK to be unlinked
before doing so.
NULL pointer dereference kernel oopses had been observed in usb_hcd_giveback_urb
when a USB device was unplugged/replugged during data transfer. This effect
was reproduced using automated USB port power control, hundreds of replug
events were performed during active transfers to confirm that the problem was
eliminated.
USB fix using a FIQ to implement split transactions
This commit adds a FIQ implementaion that schedules
the split transactions using a FIQ so we don't get
held off by the interrupt latency of Linux
dwc_otg: fix device attributes and avoid kernel warnings on boot
dcw_otg: avoid logging function that can cause panics
See: https://github.com/raspberrypi/firmware/issues/21
Thanks to cleverca22 for fix
dwc_otg: mask correct interrupts after transaction error recovery
The dwc_otg driver will unmask certain interrupts on a transaction
that previously halted in the error state in order to reset the
QTD error count. The various fine-grained interrupt handlers do not
consider that other interrupts besides themselves were unmasked.
By disabling the two other interrupts only ever enabled in DMA mode
for this purpose, we can avoid unnecessary function calls in the
IRQ handler. This will also prevent an unneccesary FIQ interrupt
from being generated if the FIQ is enabled.
dwc_otg: fiq: prevent FIQ thrash and incorrect state passing to IRQ
In the case of a transaction to a device that had previously aborted
due to an error, several interrupts are enabled to reset the error
count when a device responds. This has the side-effect of making the
FIQ thrash because the hardware will generate multiple instances of
a NAK on an IN bulk/interrupt endpoint and multiple instances of ACK
on an OUT bulk/interrupt endpoint. Make the FIQ mask and clear the
associated interrupts.
Additionally, on non-split transactions make sure that only unmasked
interrupts are cleared. This caused a hard-to-trigger but serious
race condition when you had the combination of an endpoint awaiting
error recovery and a transaction completed on an endpoint - due to
the sequencing and timing of interrupts generated by the dwc_otg core,
it was possible to confuse the IRQ handler.
Fix function tracing
dwc_otg: whitespace cleanup in dwc_otg_urb_enqueue
dwc_otg: prevent OOPSes during device disconnects
The dwc_otg_urb_enqueue function is thread-unsafe. In particular the
access of urb->hcpriv, usb_hcd_link_urb_to_ep, dwc_otg_urb->qtd and
friends does not occur within a critical section and so if a device
was unplugged during activity there was a high chance that the
usbcore hub_thread would try to disable the endpoint with partially-
formed entries in the URB queue. This would result in BUG() or null
pointer dereferences.
Fix so that access of urb->hcpriv, enqueuing to the hardware and
adding to usbcore endpoint URB lists is contained within a single
critical section.
dwc_otg: prevent BUG() in TT allocation if hub address is > 16
A fixed-size array is used to track TT allocation. This was
previously set to 16 which caused a crash because
dwc_otg_hcd_allocate_port would read past the end of the array.
This was hit if a hub was plugged in which enumerated as addr > 16,
due to previous device resets or unplugs.
Also add #ifdef FIQ_DEBUG around hcd->hub_port_alloc[], which grows
to a large size if 128 hub addresses are supported. This field is
for debug only for tracking which frame an allocate happened in.
dwc_otg: make channel halts with unknown state less damaging
If the IRQ received a channel halt interrupt through the FIQ
with no other bits set, the IRQ would not release the host
channel and never complete the URB.
Add catchall handling to treat as a transaction error and retry.
dwc_otg: fiq_split: use TTs with more granularity
This fixes certain issues with split transaction scheduling.
- Isochronous multi-packet OUT transactions now hog the TT until
they are completed - this prevents hubs aborting transactions
if they get a periodic start-split out-of-order
- Don't perform TT allocation on non-periodic endpoints - this
allows simultaneous use of the TT's bulk/control and periodic
transaction buffers
This commit will mainly affect USB audio playback.
dwc_otg: fix potential sleep while atomic during urb enqueue
Fixes a regression introduced with eb1b482a. Kmalloc called from
dwc_otg_hcd_qtd_add / dwc_otg_hcd_qtd_create did not always have
the GPF_ATOMIC flag set. Force this flag when inside the larger
critical section.
dwc_otg: make fiq_split_enable imply fiq_fix_enable
Failing to set up the FIQ correctly would result in
"IRQ 32: nobody cared" errors in dmesg.
dwc_otg: prevent crashes on host port disconnects
Fix several issues resulting in crashes or inconsistent state
if a Model A root port was disconnected.
- Clean up queue heads properly in kill_urbs_in_qh_list by
removing the empty QHs from the schedule lists
- Set the halt status properly to prevent IRQ handlers from
using freed memory
- Add fiq_split related cleanup for saved registers
- Make microframe scheduling reclaim host channels if
active during a disconnect
- Abort URBs with -ESHUTDOWN status response, informing
device drivers so they respond in a more correct fashion
and don't try to resubmit URBs
- Prevent IRQ handlers from attempting to handle channel
interrupts if the associated URB was dequeued (and the
driver state was cleared)
dwc_otg: prevent leaking URBs during enqueue
A dwc_otg_urb would get leaked if the HCD enqueue function
failed for any reason. Free the URB at the appropriate points.
dwc_otg: Enable NAK holdoff for control split transactions
Certain low-speed devices take a very long time to complete a
data or status stage of a control transaction, producing NAK
responses until they complete internal processing - the USB2.0
spec limit is up to 500mS. This causes the same type of interrupt
storm as seen with USB-serial dongles prior to c8edb238.
In certain circumstances, usually while booting, this interrupt
storm could cause SD card timeouts.
dwc_otg: Fix for occasional lockup on boot when doing a USB reset
dwc_otg: Don't issue traffic to LS devices in FS mode
Issuing low-speed packets when the root port is in full-speed mode
causes the root port to stop responding. Explicitly fail when
enqueuing URBs to a LS endpoint on a FS bus.
Fix ARM architecture issue with local_irq_restore()
If local_fiq_enable() is called before a local_irq_restore(flags) where
the flags variable has the F bit set, the FIQ will be erroneously disabled.
Fixup arch_local_irq_restore to avoid trampling the F bit in CPSR.
Also fix some of the hacks previously implemented for previous dwc_otg
incarnations.
dwc_otg: fiq_fsm: Base commit for driver rewrite
This commit removes the previous FIQ fixes entirely and adds fiq_fsm.
This rewrite features much more complete support for split transactions
and takes into account several OTG hardware bugs. High-speed
isochronous transactions are also capable of being performed by fiq_fsm.
All driver options have been removed and replaced with:
- dwc_otg.fiq_enable (bool)
- dwc_otg.fiq_fsm_enable (bool)
- dwc_otg.fiq_fsm_mask (bitmask)
- dwc_otg.nak_holdoff (unsigned int)
Defaults are specified such that fiq_fsm behaves similarly to the
previously implemented FIQ fixes.
fiq_fsm: Push error recovery into the FIQ when fiq_fsm is used
If the transfer associated with a QTD failed due to a bus error, the HCD
would retry the transfer up to 3 times (implementing the USB2.0
three-strikes retry in software).
Due to the masking mechanism used by fiq_fsm, it is only possible to pass
a single interrupt through to the HCD per-transfer.
In this instance host channels would fall off the radar because the error
reset would function, but the subsequent channel halt would be lost.
Push the error count reset into the FIQ handler.
fiq_fsm: Implement timeout mechanism
For full-speed endpoints with a large packet size, interrupt latency
runs the risk of the FIQ starting a transaction too late in a full-speed
frame. If the device is still transmitting data when EOF2 for the
downstream frame occurs, the hub will disable the port. This change is
not reflected in the hub status endpoint and the device becomes
unresponsive.
Prevent high-bandwidth transactions from being started too late in a
frame. The mechanism is not guaranteed: a combination of bit stuffing
and hub latency may still result in a device overrunning.
fiq_fsm: fix bounce buffer utilisation for Isochronous OUT
Multi-packet isochronous OUT transactions were subject to a few bounday
bugs. Fix them.
Audio playback is now much more robust: however, an issue stands with
devices that have adaptive sinks - ALSA plays samples too fast.
dwc_otg: Return full-speed frame numbers in HS mode
The frame counter increments on every *microframe* in high-speed mode.
Most device drivers expect this number to be in full-speed frames - this
caused considerable confusion to e.g. snd_usb_audio which uses the
frame counter to estimate the number of samples played.
fiq_fsm: save PID on completion of interrupt OUT transfers
Also add edge case handling for interrupt transports.
Note that for periodic split IN, data toggles are unimplemented in the
OTG host hardware - it unconditionally accepts any PID.
fiq_fsm: add missing case for fiq_fsm_tt_in_use()
Certain combinations of bitrate and endpoint activity could
result in a periodic transaction erroneously getting started
while the previous Isochronous OUT was still active.
fiq_fsm: clear hcintmsk for aborted transactions
Prevents the FIQ from erroneously handling interrupts
on a timed out channel.
fiq_fsm: enable by default
fiq_fsm: fix dequeues for non-periodic split transactions
If a dequeue happened between the SSPLIT and CSPLIT phases of the
transaction, the HCD would never receive an interrupt.
fiq_fsm: Disable by default
fiq_fsm: Handle HC babble errors
The HCTSIZ transfer size field raises a babble interrupt if
the counter wraps. Handle the resulting interrupt in this case.
dwc_otg: fix interrupt registration for fiq_enable=0
Additionally make the module parameter conditional for wherever
hcd->fiq_state is touched.
fiq_fsm: Enable by default
dwc_otg: Fix various issues with root port and transaction errors
Process the host port interrupts correctly (and don't trample them).
Root port hotplug now functional again.
Fix a few thinkos with the transaction error passthrough for fiq_fsm.
fiq_fsm: Implement hack for Split Interrupt transactions
Hubs aren't too picky about which endpoint we send Control type split
transactions to. By treating Interrupt transfers as Control, it is
possible to use the non-periodic queue in the OTG core as well as the
non-periodic FIFOs in the hub itself. This massively reduces the
microframe exclusivity/contention that periodic split transactions
otherwise have to enforce.
It goes without saying that this is a fairly egregious USB specification
violation, but it works.
Original idea by Hans Petter Selasky @ FreeBSD.org.
dwc_otg: FIQ support on SMP. Set up FIQ stack and handler on Core 0 only.
dwc_otg: introduce fiq_fsm_spin(un|)lock()
SMP safety for the FIQ relies on register read-modify write cycles being
completed in the correct order. Several places in the DWC code modify
registers also touched by the FIQ. Protect these by a bare-bones lock
mechanism.
This also makes it possible to run the FIQ and IRQ handlers on different
cores.
fiq_fsm: fix build on bcm2708 and bcm2709 platforms
dwc_otg: put some barriers back where they should be for UP
bcm2709/dwc_otg: Setup FIQ on core 1 if >1 core active
dwc_otg: fixup read-modify-write in critical paths
Be more careful about read-modify-write on registers that the FIQ
also touches.
Guard fiq_fsm_spin_lock with fiq_enable check
fiq_fsm: Falling out of the state machine isn't fatal
This edge case can be hit if the port is disabled while the FIQ is
in the middle of a transaction. Make the effects less severe.
Also get rid of the useless return value.
squash: dwc_otg: Allow to build without SMP
usb: core: make overcurrent messages more prominent
Hub overcurrent messages are more serious than "debug". Increase loglevel.
usb: dwc_otg: Don't use dma_to_virt()
Commit 6ce0d20 changes dma_to_virt() which breaks this driver.
Open code the old dma_to_virt() implementation to work around this.
Limit the use of __bus_to_virt() to cases where transfer_buffer_length
is set and transfer_buffer is not set. This is done to increase the
chance that this driver will also work on ARCH_BCM2835.
transfer_buffer should not be NULL if the length is set, but the
comment in the code indicates that there are situations where this
might happen. drivers/usb/isp1760/isp1760-hcd.c also has a similar
comment pointing to a possible: 'usb storage / SCSI bug'.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: Fix crash when fiq_enable=0
dwc_otg: fiq_fsm: Make high-speed isochronous strided transfers work properly
Certain low-bandwidth high-speed USB devices (specialist audio devices,
compressed-frame webcams) have packet intervals > 1 microframe.
Stride these transfers in the FIQ by using the start-of-frame interrupt
to restart the channel at the right time.
dwc_otg: Force host mode to fix incorrect compute module boards
dwc_otg: Add ARCH_BCM2835 support
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: Simplify FIQ irq number code
Dropping ATAGS means we can simplify the FIQ irq number code.
Also add error checking on the returned irq number.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: Remove duplicate gadget probe/unregister function
dwc_otg: Properly set the HFIR
Douglas Anderson reported:
According to the most up to date version of the dwc2 databook, the FRINT
field of the HFIR register should be programmed to:
* 125 us * (PHY clock freq for HS) - 1
* 1000 us * (PHY clock freq for FS/LS) - 1
This is opposed to older versions of the doc that claimed it should be:
* 125 us * (PHY clock freq for HS)
* 1000 us * (PHY clock freq for FS/LS)
and reported lower timing jitter on a USB analyser
dcw_otg: trim xfer length when buffer larger than allocated size is received
dwc_otg: Don't free qh align buffers in atomic context
dwc_otg: Enable the hack for Split Interrupt transactions by default
dwc_otg.fiq_fsm_mask=0xF has long been a suggestion for users with audio stutters or other USB bandwidth issues.
So far we are aware of many success stories but no failure caused by this setting.
Make it a default to learn more.
See: https://www.raspberrypi.org/forums/viewtopic.php?f=28&t=70437
Signed-off-by: popcornmix <popcornmix@gmail.com>
This is a hack until a proper solution is agreed upon.
Martin Sperl is doing some work in this area.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Load driver early since at least bcm2708_fb doesn't support deferred
probing and even if it did, we don't want the video driver deferred.
Support the legacy DMA API which is needed by bcm2708_fb.
Don't mask out channel 2.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
The VideoCore bootloader passes in Serial number and
Revision number through Device Tree. Make these available to
userspace through /proc/cpuinfo.
Mainline status:
There is a commit in linux-next that standardize passing the serial
number through Device Tree (string: /serial-number):
ARM: 8355/1: arch: Show the serial number from devicetree in cpuinfo
There was an attempt to do the same with the revision number, but it
didn't get in:
[PATCH v2 1/2] arm: devtree: Set system_rev from DT revision
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
The spi-bcm2835 driver automatically uses GPIO chip-selects due to
some unreliability of the native ones. In doing so it chooses the
same pins as the native chip-selects would use, but the existing
code always uses pins 7 and 8, wherever the SPI function is mapped.
Search the pinctrl group assigned to the driver for pins that
correspond to native chip-selects, and use those for GPIO chip-
selects.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
When dynamically unloading overlays, it is important that freed pins are
restored to being inputs to prevent functions from being enabled in
multiple places at once.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Although the GPIO controller can generate three interrupts (four counting
the common one), the device tree files currently only specify two. In the
absence of the third, simply don't register that interrupt (as opposed to
registering 0), which has the effect of making it impossible to generate
interrupts for GPIOs 46-53 which, since they share pins with the SD card
interface, is unlikely to be a problem.
Contrary to the documentation, the BCM2835 GPIO controller actually has
four interrupt lines - one each for the three IRQ groups and one common. Rather
confusingly, the GPIO interrupt groups don't correspond directly with the GPIO
control banks. Instead, GPIOs 0-27 generate IRQ GPIO0, 28-45 GPIO1 and
46-53 GPIO2.
Awkwardly, the GPIOS for IRQ GPIO1 straddle two 32-entry GPIO banks, so it is
cleaner to split out a function to process the interrupts for a single GPIO
bank.
This bug has only just been observed because GPIOs above 27 can only be
accessed on an old Raspberry Pi with the optional P5 header fitted, where
the pins are often used for I2S instead.
Add a duplicate irq range with an offset on the hwirq's so the
driver can detect that enable_fiq() is used.
Tested with downstream dwc_otg USB controller driver.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
The old arch-specific IRQ macros included a dsb to ensure the
write to clear the mailbox interrupt completed before returning
from the interrupt. The BCM2836 irqchip driver needs the same
precaution to avoid spurious interrupts.
Spurious interrupts are still possible for other reasons,
though, so trap them early.
See commit dae803e165 -- the warning is
expected sometimes when using CMA. However, that commit still spams
my kernel log with these warnings.
Signed-off-by: Eric Anholt <eric@anholt.net>
tty_port_hangup sets a port's tty field to NULL (holding the port lock),
but uart_tx_stopped, called from __uart_start (with the port lock),
uses the tty field without checking for NULL.
Change uart_tx_stopped to treat a NULL tty field as another stopped
indication.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
smsc95xx is adjusting truesize when it shouldn't, and following a recent patch from Eric this is now triggering warnings.
This patch stops smsc95xx from changing truesize.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
commit 3932a86b4b upstream.
While debugging timeouts happening in my application workload (ScyllaDB), I have
observed calls to open() taking a long time, ranging everywhere from 2 seconds -
the first ones that are enough to time out my application - to more than 30
seconds.
The problem seems to happen because XFS may block on pending metadata updates
under certain circumnstances, and that's confirmed with the following backtrace
taken by the offcputime tool (iovisor/bcc):
ffffffffb90c57b1 finish_task_switch
ffffffffb97dffb5 schedule
ffffffffb97e310c schedule_timeout
ffffffffb97e1f12 __down
ffffffffb90ea821 down
ffffffffc046a9dc xfs_buf_lock
ffffffffc046abfb _xfs_buf_find
ffffffffc046ae4a xfs_buf_get_map
ffffffffc046babd xfs_buf_read_map
ffffffffc0499931 xfs_trans_read_buf_map
ffffffffc044a561 xfs_da_read_buf
ffffffffc0451390 xfs_dir3_leaf_read.constprop.16
ffffffffc0452b90 xfs_dir2_leaf_lookup_int
ffffffffc0452e0f xfs_dir2_leaf_lookup
ffffffffc044d9d3 xfs_dir_lookup
ffffffffc047d1d9 xfs_lookup
ffffffffc0479e53 xfs_vn_lookup
ffffffffb925347a path_openat
ffffffffb9254a71 do_filp_open
ffffffffb9242a94 do_sys_open
ffffffffb9242b9e sys_open
ffffffffb97e42b2 entry_SYSCALL_64_fastpath
00007fb0698162ed [unknown]
Inspecting my run with blktrace, I can see that the xfsaild kthread exhibit very
high "Dispatch wait" times, on the dozens of seconds range and consistent with
the open() times I have saw in that run.
Still from the blktrace output, we can after searching a bit, identify the
request that wasn't dispatched:
8,0 11 152 81.092472813 804 A WM 141698288 + 8 <- (8,1) 141696240
8,0 11 153 81.092472889 804 Q WM 141698288 + 8 [xfsaild/sda1]
8,0 11 154 81.092473207 804 G WM 141698288 + 8 [xfsaild/sda1]
8,0 11 206 81.092496118 804 I WM 141698288 + 8 ( 22911) [xfsaild/sda1]
<==== 'I' means Inserted (into the IO scheduler) ===================================>
8,0 0 289372 96.718761435 0 D WM 141698288 + 8 (15626265317) [swapper/0]
<==== Only 15s later the CFQ scheduler dispatches the request ======================>
As we can see above, in this particular example CFQ took 15 seconds to dispatch
this request. Going back to the full trace, we can see that the xfsaild queue
had plenty of opportunity to run, and it was selected as the active queue many
times. It would just always be preempted by something else (example):
8,0 1 0 81.117912979 0 m N cfq1618SN / insert_request
8,0 1 0 81.117913419 0 m N cfq1618SN / add_to_rr
8,0 1 0 81.117914044 0 m N cfq1618SN / preempt
8,0 1 0 81.117914398 0 m N cfq767A / slice expired t=1
8,0 1 0 81.117914755 0 m N cfq767A / resid=40
8,0 1 0 81.117915340 0 m N / served: vt=1948520448 min_vt=1948520448
8,0 1 0 81.117915858 0 m N cfq767A / sl_used=1 disp=0 charge=0 iops=1 sect=0
where cfq767 is the xfsaild queue and cfq1618 corresponds to one of the ScyllaDB
IO dispatchers.
The requests preempting the xfsaild queue are synchronous requests. That's a
characteristic of ScyllaDB workloads, as we only ever issue O_DIRECT requests.
While it can be argued that preempting ASYNC requests in favor of SYNC is part
of the CFQ logic, I don't believe that doing so for 15+ seconds is anyone's
goal.
Moreover, unless I am misunderstanding something, that breaks the expectation
set by the "fifo_expire_async" tunable, which in my system is set to the
default.
Looking at the code, it seems to me that the issue is that after we make
an async queue active, there is no guarantee that it will execute any request.
When the queue itself tests if it cfq_may_dispatch() it can bail if it sees SYNC
requests in flight. An incoming request from another queue can also preempt it
in such situation before we have the chance to execute anything (as seen in the
trace above).
This patch sets the must_dispatch flag if we notice that we have requests
that are already fifo_expired. This flag is always cleared after
cfq_dispatch_request() returns from cfq_dispatch_requests(), so it won't pin
the queue for subsequent requests (unless they are themselves expired)
Care is taken during preempt to still allow rt requests to preempt us
regardless.
Testing my workload with this patch applied produces much better results.
From the application side I see no timeouts, and the open() latency histogram
generated by systemtap looks much better, with the worst outlier at 131ms:
Latency histogram of xfs_buf_lock acquisition (microseconds):
value |-------------------------------------------------- count
0 | 11
1 |@@@@ 161
2 |@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ 1966
4 |@ 54
8 | 36
16 | 7
32 | 0
64 | 0
~
1024 | 0
2048 | 0
4096 | 1
8192 | 1
16384 | 2
32768 | 0
65536 | 0
131072 | 1
262144 | 0
524288 | 0
Signed-off-by: Glauber Costa <glauber@scylladb.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: linux-block@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Glauber Costa <glauber@scylladb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a818101d7b upstream.
An NULL-pointer dereference happens in cachefiles_mark_object_inactive()
when it tries to read i_blocks so that it can tell the cachefilesd daemon
how much space it's making available.
The problem is that cachefiles_drop_object() calls
cachefiles_mark_object_inactive() after calling cachefiles_delete_object()
because the object being marked active staves off attempts to (re-)use the
file at that filename until after it has been deleted. This means that
d_inode is NULL by the time we come to try to access it.
To fix the problem, have the caller of cachefiles_mark_object_inactive()
supply the number of blocks freed up.
Without this, the following oops may occur:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000098
IP: [<ffffffffa06c5cc1>] cachefiles_mark_object_inactive+0x61/0xb0 [cachefiles]
...
CPU: 11 PID: 527 Comm: kworker/u64:4 Tainted: G I ------------ 3.10.0-470.el7.x86_64 #1
Hardware name: Hewlett-Packard HP Z600 Workstation/0B54h, BIOS 786G4 v03.19 03/11/2011
Workqueue: fscache_object fscache_object_work_func [fscache]
task: ffff880035edaf10 ti: ffff8800b77c0000 task.ti: ffff8800b77c0000
RIP: 0010:[<ffffffffa06c5cc1>] cachefiles_mark_object_inactive+0x61/0xb0 [cachefiles]
RSP: 0018:ffff8800b77c3d70 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff8800bf6cc400 RCX: 0000000000000034
RDX: 0000000000000000 RSI: ffff880090ffc710 RDI: ffff8800bf761ef8
RBP: ffff8800b77c3d88 R08: 2000000000000000 R09: 0090ffc710000000
R10: ff51005d2ff1c400 R11: 0000000000000000 R12: ffff880090ffc600
R13: ffff8800bf6cc520 R14: ffff8800bf6cc400 R15: ffff8800bf6cc498
FS: 0000000000000000(0000) GS:ffff8800bb8c0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000098 CR3: 00000000019ba000 CR4: 00000000000007e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Stack:
ffff880090ffc600 ffff8800bf6cc400 ffff8800867df140 ffff8800b77c3db0
ffffffffa06c48cb ffff880090ffc600 ffff880090ffc180 ffff880090ffc658
ffff8800b77c3df0 ffffffffa085d846 ffff8800a96b8150 ffff880090ffc600
Call Trace:
[<ffffffffa06c48cb>] cachefiles_drop_object+0x6b/0xf0 [cachefiles]
[<ffffffffa085d846>] fscache_drop_object+0xd6/0x1e0 [fscache]
[<ffffffffa085d615>] fscache_object_work_func+0xa5/0x200 [fscache]
[<ffffffff810a605b>] process_one_work+0x17b/0x470
[<ffffffff810a6e96>] worker_thread+0x126/0x410
[<ffffffff810a6d70>] ? rescuer_thread+0x460/0x460
[<ffffffff810ae64f>] kthread+0xcf/0xe0
[<ffffffff810ae580>] ? kthread_create_on_node+0x140/0x140
[<ffffffff81695418>] ret_from_fork+0x58/0x90
[<ffffffff810ae580>] ? kthread_create_on_node+0x140/0x140
The oopsing code shows:
callq 0xffffffff810af6a0 <wake_up_bit>
mov 0xf8(%r12),%rax
mov 0x30(%rax),%rax
mov 0x98(%rax),%rax <---- oops here
lock add %rax,0x130(%rbx)
where this is:
d_backing_inode(object->dentry)->i_blocks
Fixes: a5b3a80b89 (CacheFiles: Provide read-and-reset release counters for cachefilesd)
Reported-by: Jianhong Yin <jiyin@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Steve Dickson <steved@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f2b20f6ee8 upstream.
This fixes a bug where the permission was not properly checked in
overlayfs. The testcase is ltp/utimensat01.
It is also cleaner and safer to do the permission checking in the vfs
helper instead of the caller.
This patch introduces an additional ia_valid flag ATTR_TOUCH (since
touch(1) is the most obvious user of utimes(NULL)) that is passed into
notify_change whenever the conditions for this special permission checking
mode are met.
Reported-by: Aihua Zhang <zhangaihua1@huawei.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Tested-by: Aihua Zhang <zhangaihua1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a8db79889 upstream.
After backporting commit ee44b4bc05 ("dlm: use sctp 1-to-1 API")
series to a kernel with an older workqueue which didn't use RCU yet, it
was noticed that we are freeing the workqueues in dlm_lowcomms_stop()
too early as free_conn() will try to access that memory for canceling
the queued works if any.
This issue was introduced by commit 0d737a8cfd as before it such
attempt to cancel the queued works wasn't performed, so the issue was
not present.
This patch fixes it by simply inverting the free order.
Fixes: 0d737a8cfd ("dlm: fix race while closing connections")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 80da44c29d upstream.
This patch changes the p8_ghash driver to use ghash-generic as a fixed
fallback implementation. This allows the correct value of descsize to be
defined directly in its shash_alg structure and avoids problems with
incorrect buffer sizes when its state is exported or imported.
Reported-by: Jan Stancek <jstancek@redhat.com>
Fixes: cc333cd68d ("crypto: vmx - Adding GHASH routines for VMX module")
Signed-off-by: Marcelo Cerri <marcelo.cerri@canonical.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a397ba829d upstream.
Move common values and types used by ghash-generic to a new header file
so drivers can directly use ghash-generic as a fallback implementation.
Fixes: cc333cd68d ("crypto: vmx - Adding GHASH routines for VMX module")
Signed-off-by: Marcelo Cerri <marcelo.cerri@canonical.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b623df614 upstream.
When zeroing blocks for DAX allocations, we also have to unmap aliases
in the block device mappings. Otherwise writeback can overwrite zeros
with stale data from block device page cache.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e81d44778d upstream.
The commit 6050d47adc: "ext4: bail out from make_indexed_dir() on
first error" could end up leaking bh2 in the error path.
[ Also avoid renaming bh2 to bh, which just confuses things --tytso ]
Signed-off-by: yangsheng <yngsion@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cca32b7eeb upstream.
Currently when doing a DAX hole punch with ext4 we fail to do a writeback.
This is because the logic around filemap_write_and_wait_range() in
ext4_punch_hole() only looks for dirty page cache pages in the radix tree,
not for dirty DAX exceptional entries.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e800c0359 upstream.
Pages clear buffers after ext4 delayed block allocation failed,
However, it does not clean its pte_dirty flag.
if the pages unmap ,in cording to the pte_dirty ,
unmap_page_range may try to call __set_page_dirty,
which may lead to the bugon at
mpage_prepare_extent_to_map:head = page_buffers(page);.
This patch just call clear_page_dirty_for_io to clean pte_dirty
at mpage_release_unused_pages for pages mmaped.
Steps to reproduce the bug:
（1） mmap a file in ext4
addr = (char *)mmap(NULL, 4096, PROT_READ|PROT_WRITE, MAP_SHARED,
fd, 0);
memset(addr, 'i', 4096);
（2） return EIO at
ext4_writepages->mpage_map_and_submit_extent->mpage_map_one_extent
which causes this log message to be print:
ext4_msg(sb, KERN_CRIT,
"Delayed block allocation failed for "
"inode %lu at logical offset %llu with"
" max blocks %u with error %d",
inode->i_ino,
(unsigned long long)map->m_lblk,
(unsigned)map->m_len, -err);
(3）Unmap the addr cause warning at
__set_page_dirty:WARN_ON_ONCE(warn && !PageUptodate(page));
(4) wait for a minute,then bugon happen.
Signed-off-by: wangguang <wangguang03@zte.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 93e3b4e663 upstream.
Now, ext4_do_update_inode() clears high 16-bit fields of uid/gid
of deleted and evicted inode to fix up interoperability with old
kernels. However, it checks only i_dtime of an inode to determine
whether the inode was deleted and evicted, and this is very risky,
because i_dtime can be used for the pointer maintaining orphan inode
list, too. We need to further check whether the i_dtime is being
used for the orphan inode list even if the i_dtime is not NULL.
We found that high 16-bit fields of uid/gid of inode are unintentionally
and permanently cleared when the inode truncation is just triggered,
but not finished, and the inode metadata, whose high uid/gid bits are
cleared, is written on disk, and the sudden power-off follows that
in order.
Signed-off-by: Daeho Jeong <daeho.jeong@samsung.com>
Signed-off-by: Hobin Woo <hobin.woo@samsung.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 14fbd4aa61 upstream.
Online defragging of encrypted files is not currently implemented.
However, the move extent ioctl can still return successfully when
called. For example, this occurs when xfstest ext4/020 is run on an
encrypted file system, resulting in a corrupted test file and a
corresponding test failure.
Until the proper functionality is implemented, fail the move extent
ioctl if either the original or donor file is encrypted.
Signed-off-by: Eric Whitney <enwlinux@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2a9737f45 upstream.
We triggered a deadloop in truncate_inode_pages_range() on 32 bits
architecture with the test case bellow:
...
fd = open();
write(fd, buf, 4096);
preadv64(fd, &iovec, 1, 0xffffffff000);
ftruncate(fd, 0);
...
Then ftruncate() will not return forever.
The filesystem used in this case is ubifs, but it can be triggered on
many other filesystems.
When preadv64() is called with offset=0xffffffff000, a page with
index=0xffffffff will be added to the radix tree of ->mapping. Then
this page can be found in ->mapping with pagevec_lookup(). After that,
truncate_inode_pages_range(), which is called in ftruncate(), will fall
into an infinite loop:
- find a page with index=0xffffffff, since index>=end, this page won't
be truncated
- index++, and index become 0
- the page with index=0xffffffff will be found again
The data type of index is unsigned long, so index won't overflow to 0 on
64 bits architecture in this case, and the dead loop won't happen.
Since truncate_inode_pages_range() is executed with holding lock of
inode->i_rwsem, any operation related with this lock will be blocked,
and a hung task will happen, e.g.:
INFO: task truncate_test:3364 blocked for more than 120 seconds.
...
call_rwsem_down_write_failed+0x17/0x30
generic_file_write_iter+0x32/0x1c0
ubifs_write_iter+0xcc/0x170
__vfs_write+0xc4/0x120
vfs_write+0xb2/0x1b0
SyS_write+0x46/0xa0
The page with index=0xffffffff added to ->mapping is useless. Fix this
by checking the read position before allocating pages.
Link: http://lkml.kernel.org/r/1475151010-40166-1-git-send-email-fangwei1@huawei.com
Signed-off-by: Wei Fang <fangwei1@huawei.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07d0e9a847 upstream.
If a VFC port gets unmapped in the VIOS, it may not respond with a CRQ
init complete following H_REG_CRQ. If this occurs, we can end up having
called scsi_block_requests and not a resulting unblock until the init
complete happens, which may never occur, and we end up hanging I/O
requests. This patch ensures the host action stay set to
IBMVFC_HOST_ACTION_TGT_DEL so we move all rports into devloss state and
unblock unless we receive an init complete.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61ab0d403b upstream.
In sst_prepare_and_post_msg(), when a response is received in "block",
the following code gets executed:
*data = kzalloc(block->size, GFP_KERNEL);
memcpy(data, (void *) block->data, block->size);
The memcpy() call overwrites the content of the *data pointer instead of
filling the newly-allocated memory (which pointer is hold by *data).
Fix this by merging kzalloc+memcpy into a single kmemdup() call.
Thanks Joe Perches for suggesting using kmemdup()
Fixes: 60dc8dbacb ("ASoC: Intel: sst: Add some helper functions")
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7f00ee2bbc upstream.
Flowrings contain skbs waiting for transmission that were passed to us
by netif. It means we checked every one of them looking for 802.1x
Ethernet type. When deleting flowring we have to use freeing function
that will check for 802.1x type as well.
Freeing skbs without a proper check was leading to counter not being
properly decreased. This was triggering a WARNING every time
brcmf_netdev_wait_pend8021x was called.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23e9c128ad upstream.
This function is called from get_station callback which means that every
time user space was getting/dumping station(s) we were leaking 2 KiB.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Fixes: 1f0dc59a6d ("brcmfmac: rework .get_station() callback")
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7703773ef1 upstream.
The struct cfg80211_pmksa defines its bssid field as:
const u8 *bssid;
contrary to struct brcmf_pmksa, which uses:
u8 bssid[ETH_ALEN];
Therefore in brcmf_cfg80211_del_pmksa(), &pmksa->bssid takes the address
of this field (of type u8**), not the one of its content (which would be
u8*). Remove the & operator to make brcmf_dbg("%pM") and memcmp()
behave as expected.
This bug have been found using a custom static checker (which checks the
usage of %p... attributes at build time). It has been introduced in
commit 6c404f34f2 ("brcmfmac: Cleanup pmksa cache handling code"),
which replaced pmksa->bssid by &pmksa->bssid while refactoring the code,
without modifying struct cfg80211_pmksa definition.
Replace &pmk[i].bssid with pmk[i].bssid too to make the code clearer,
this change does not affect the semantic.
Fixes: 6c404f34f2 ("brcmfmac: Cleanup pmksa cache handling code")
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit edfc23ee3e upstream.
Although rare, it's possible to hit PCI error early on device
probe, meaning possibly some structs are not entirely initialized,
and some might even be completely uninitialized, leading to NULL
pointer dereference.
The i40e driver currently presents a "bad" behavior if device hits
such early PCI error: firstly, the struct i40e_pf might not be
attached to pci_dev yet, leading to a NULL pointer dereference on
access to pf->state.
Even checking if the struct is NULL and avoiding the access in that
case isn't enough, since the driver cannot recover from PCI error
that early; in our experiments we saw multiple failures on kernel
log, like:
[549.664] i40e 0007:01:00.1: Initial pf_reset failed: -15
[549.664] i40e: probe of 0007:01:00.1 failed with error -15
[...]
[871.644] i40e 0007:01:00.1: The driver for the device stopped because the
device firmware failed to init. Try updating your NVM image.
[871.644] i40e: probe of 0007:01:00.1 failed with error -32
[...]
[872.516] i40e 0007:01:00.0: ARQ: Unknown event 0x0000 ignored
Between the first probe failure (error -15) and the second (error -32)
another PCI error happened due to the first bad probe. Also, driver
started to flood console with those ARQ event messages.
This patch will prevent these issues by allowing error recovery
mechanism to remove the failed device from the system instead of
trying to recover from early PCI errors during device probe.
Signed-off-by: Guilherme G Piccoli <gpiccoli@linux.vnet.ibm.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a09f99edde upstream.
Fuse allowed VFS to set mode in setattr in order to clear suid/sgid on
chown and truncate, and (since writeback_cache) write. The problem with
this is that it'll potentially restore a stale mode.
The poper fix would be to let the filesystems do the suid/sgid clearing on
the relevant operations. Possibly some are already doing it but there's no
way we can detect this.
So fix this by refreshing and recalculating the mode. Do this only if
ATTR_KILL_S[UG]ID is set to not destroy performance for writes. This is
still racy but the size of the window is reduced.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e2b8828ff upstream.
Without "default_permissions" the userspace filesystem's lookup operation
needs to perform the check for search permission on the directory.
If directory does not allow search for everyone (this is quite rare) then
userspace filesystem has to set entry timeout to zero to make sure
permissions are always performed.
Changing the mode bits of the directory should also invalidate the
(previously cached) dentry to make sure the next lookup will have a chance
of updating the timeout, if needed.
Reported-by: Jean-Pierre André <jean-pierre.andre@wanadoo.fr>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cb3ae6d25a upstream.
Make sure userspace filesystem is returning a well formed list of xattr
names (zero or more nonzero length, null terminated strings).
[Michael Theall: only verify in the nonzero size case]
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a0245eb76a upstream.
Original commit, which added support for Armada CP110 system controller
used global variables for storing all clock information. It worked
fine for Armada 7k SoC, with single CP110 block. After dual-CP110 Armada 8k
was introduced, the data got overwritten and corrupted.
This patch fixes the issue by allocating resources dynamically in the
driver probe and storing it as platform drvdata.
Fixes: d3da3eaef7 ("clk: mvebu: new driver for Armada CP110 system ...")
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ad715b268a upstream.
Armada CP110 system controller comprises its own routine responsble
for registering gate clocks. Among others 'flags' field in
struct clk_init_data was not set, using a random values, which
may cause an unpredicted behavior.
This patch fixes the problem by resetting all fields of clk_init_data
before assigning values for all gated clocks of Armada 7k/8k SoCs family.
Fixes: d3da3eaef7 ("clk: mvebu: new driver for Armada CP110 system ...")
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 72f53af265 upstream.
There is a a bug in defered ack stuff that causes a race with the
destroy of a QP.
A packet causes a defered ack to be pended by putting the QP
into an rcd queue.
A return from the driver interrupt processing will process that rcd
queue of QPs and attempt to do a direct send of the ack. At this
point no locks are held and the above QP could now be put in the reset
state in the qp destroy logic. A refcount protects the QP while it
is in the rcd queue so it isn't going anywhere yet.
If the direct send fails to allocate a pio buffer,
hfi1_schedule_send() is called to trigger sending an ack from the
send engine. There is no state test in that code path.
The refcount is then dropped from the driver.c caller
potentially allowing the qp destroy to continue from its
refcount wait in parallel with the workqueue scheduling of the qp.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e728ae271f upstream.
The device lock was unnecessary obtained in bus rescan work before the
amthif client search. That causes incorrect lock ordering and task
hang:
...
[88004.613213] INFO: task kworker/1:14:21832 blocked for more than 120 seconds.
...
[88004.645934] Workqueue: events mei_cl_bus_rescan_work
...
The correct lock order is
cl_bus_lock
device_lock
me_clients_rwsem
Move device_lock into amthif init function that called
after me_clients_rwsem is released.
This fixes regression introduced by commit:
commit 025fb792ba ("mei: split amthif client init from end of clients enumeration")
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6675df311d upstream.
There are two separate issues that can lead to corrupted free space
trees.
1. The free space tree bitmaps had an endianness issue on big-endian
systems which is fixed by an earlier patch in this series.
2. btrfs-progs before v4.7.3 modified filesystems without updating the
free space tree.
To catch both of these issues at once, we need to force the free space
tree to be rebuilt. To do so, add a FREE_SPACE_TREE_VALID compat_ro bit.
If the bit isn't set, we know that it was either produced by a broken
big-endian kernel or may have been corrupted by btrfs-progs.
This also provides us with a way to add rudimentary read-write support
for the free space tree to btrfs-progs: it can just clear this bit and
have the kernel rebuild the free space tree.
Tested-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Tested-by: Chandan Rajendra <chandan@linux.vnet.ibm.com>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2fe1d55134 upstream.
In convert_free_space_to_{bitmaps,extents}(), we buffer the free space
bitmaps in memory and copy them directly to/from the extent buffers with
{read,write}_extent_buffer(). The extent buffer bitmap helpers use byte
granularity, which is equivalent to a little-endian bitmap. This means
that on big-endian systems, the in-memory bitmaps will be written to
disk byte-swapped. To fix this, use byte-granularity for the bitmaps in
memory.
Fixes: a5ed918285 ("Btrfs: implement the free space B-tree")
Tested-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Tested-by: Chandan Rajendra <chandan@linux.vnet.ibm.com>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ee6d1cb39 upstream.
Ben Greear reported:
> I see lots of instability as soon as I load up the carl9710 NIC.
> My application is going to be poking at it's debugfs files...
>
> BUG: KASAN: slab-out-of-bounds in carl9170_debugfs_read+0xd5/0x2a0
> [carl9170] at addr 0xffff8801bc1208b0
> Read of size 8 by task btserver/5888
> =======================================================================
> BUG kmalloc-256 (Tainted: G W ): kasan: bad access detected
> -----------------------------------------------------------------------
>
> INFO: Allocated in seq_open+0x50/0x100 age=2690 cpu=2 pid=772
>...
This breakage was caused by the introduction of intermediate
fops in debugfs by commit 9fd4dcece4
("debugfs: prevent access to possibly dead file_operations at file open")
Thankfully, the original/real fops are still available in d_fsdata.
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9c4a45b17e upstream.
This patch fixes a crash that happens because b43legacy's
debugfs code expects file->f_op to be a pointer to its own
b43legacy_debugfs_fops struct. This is no longer the case
since commit 9fd4dcece4
("debugfs: prevent access to possibly dead file_operations at file open")
Reviewed-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 51b275a6fe upstream.
This patch fixes a crash that happens because b43's
debugfs code expects file->f_op to be a pointer to
its own b43_debugfs_fops struct. This is no longer
the case since commit 9fd4dcece4
("debugfs: prevent access to possibly dead file_operations at file open")
Reviewed-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 86f0e06767 upstream.
This patch introduces an accessor which can be used
by the users of debugfs (drivers, fs, ...) to get the
original file_operations struct. It also removes the
REAL_FOPS_DEREF macro in file.c and converts the code
to use the public version.
Previously, REAL_FOPS_DEREF was only available within
the file.c of debugfs. But having a public getter
available for debugfs users is important as some
drivers (carl9170 and b43) use the pointer of the
original file_operations in conjunction with container_of()
within their debugfs implementations.
Reviewed-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd5d38b052 upstream.
Commit d9676fa152 ("ARCv2: Enable LOCKDEP"), changed
local_save_flags() to not return raw STATUS32 but encoded in the form
such that it could be fed directly to CLRI/SETI instructions.
However the STATUS32.E[] was not captured correctly as it corresponds to
bits [4:1] in the register and not [3:0]
Fixes: d9676fa152 ("ARCv2: Enable LOCKDEP")
Cc: Evgeny Voevodin <evgeny.voevodin@intel.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bc0c7ece61 upstream.
In the end of "arc_init_IRQ" STATUS32.IE flag is going to be affected by
"flag" instruction but "flag" never touches IE flag on ARCv2. So "kflag"
instruction must be used instead of "flag".
Signed-off-by: Yuriy Kolerov <yuriy.kolerov@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b3965767d8 upstream.
There are calls to serial8250_rpm_{get|put}() in __do_stop_tx_rs485() that are
certainly placed in a wrong location. I dunno how it had been tested with
runtime PM enabled because it is obvious "sleep in atomic context" error.
Besides that serial8250_rpm_get() is called immediately after an IO just
happened. It implies that the device is already powered on, see implementation
of serial8250_em485_rts_after_send() and serial8250_clear_fifos() for the
details.
There is no bug have been seen due to, as I can guess, use of auto suspend mode
when scheduled transaction to suspend is invoked quite lately than it's needed
for a few writes to the port. It might be possible to trigger a warning if
stop_tx_timer fires when device is suspended.
Refactor the code to use runtime PM only in case of timer function.
Fixes: 0c66940d58 ("tty/serial/8250: fix RS485 half-duplex RX")
Cc: "Matwey V. Kornilov" <matwey@sai.msu.ru>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4b75f80003 upstream.
The USR2_DCDIN bit is tested for in register usr1. As the name
suggests the usr2 register should be used instead. This fixes
reading the Carrier detect status.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Fixes: 90ebc48386 ("serial: imx: repair and complete handshaking")
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 19be0eaffa upstream.
This is an ancient bug that was actually attempted to be fixed once
(badly) by me eleven years ago in commit 4ceb5db975 ("Fix
get_user_pages() race for write access") but that was then undone due to
problems on s390 by commit f33ea7f404 ("fix get_user_pages bug").
In the meantime, the s390 situation has long been fixed, and we can now
fix it by checking the pte_dirty() bit properly (and do it better). The
s390 dirty bit was implemented in abf09bed3c ("s390/mm: implement
software dirty bits") which made it into v3.9. Earlier kernels will
have to look at the page state itself.
Also, the VM has become more scalable, and what used a purely
theoretical race back then has become easier to trigger.
To fix it, we introduce a new internal FOLL_COW flag to mark the "yes,
we already did a COW" rather than play racy games with FOLL_WRITE that
is very fundamental, and then use the pte dirty flag to validate that
the FOLL_COW flag is still valid.
Reported-and-tested-by: Phil "not Paul" Oester <kernel@linuxace.com>
Acked-by: Hugh Dickins <hughd@google.com>
Reviewed-by: Michal Hocko <mhocko@suse.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Nick Piggin <npiggin@gmail.com>
Cc: Greg Thelen <gthelen@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 791cc43b36 upstream.
Commit 2a6fba6 "xfs: only return -errno or success from attr ->put_listent"
changes the returnvalue of __xfs_xattr_put_listen to 0 in case when there is
insufficient space in the buffer assuming that setting context->count to -1
would be enough, but all of the ->put_listent callers only check seen_enough.
This results in a failed assertion:
XFS: Assertion failed: context->count >= 0, file: fs/xfs/xfs_xattr.c, line: 175
in insufficient buffer size case.
This is only reproducible with at least 2 xattrs and only when the buffer
gets depleted before the last one.
Furthermore if buffersize is such that it is enough to hold the last xattr's
name, but not enough to hold the sum of preceeding xattr names listxattr won't
fail with ERANGE, but will suceed returning last xattr's name without the
first character. The first character end's up overwriting data stored at
(context->alist - 1).
Signed-off-by: Artem Savkov <asavkov@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Cc: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 72fd50e14e upstream.
The req_canceled() callback is used by tpm_transmit() periodically to
check whether the request has been canceled while it is receiving a
response from the TPM.
The TPM_CRB_CTRL_CANCEL register was cleared already in the crb_cancel
callback, which has two consequences:
* Cancel might not happen.
* req_canceled() always returns zero.
A better place to clear the register is when starting to send a new
command. The behavior of TPM_CRB_CTRL_CANCEL is described in the
section 5.5.3.6 of the PTP specification.
Fixes: 30fc8d138e ("tpm: TPM 2.0 CRB Interface")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d4816edfe7 upstream.
Unseal and load operations should be done as an atomic operation. This
commit introduces unlocked tpm_transmit() so that tpm2_unseal_trusted()
can do the locking by itself.
Fixes: 0fe5480303 ("keys, trusted: seal/unseal with TPM 2.0 chips")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e71b9dff06 upstream.
Ima tries to call ->setxattr() on overlayfs dentry after having locked
underlying inode, which results in a deadlock.
Reported-by: Krisztian Litkey <kli@iki.fi>
Fixes: 4bacc9c923 ("overlayfs: Make f_path always point to the overlay and f_inode to the underlay")
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Cc: Mimi Zohar <zohar@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca88696e8b upstream.
The Qualcomm PMIC GPIO and MPP lines are problematic: the
are fetched from the main MFD driver with platform_get_irq()
which means that at this point they will all be assigned the
flags set up for the interrupts in the device tree.
That is problematic since these are flagged as rising edge
and an this point the interrupt descriptor is assigned a
rising edge, while the only thing the GPIO/MPP drivers really
do is issue irq_get_irqchip_state() on the line to read it
out and to provide a .to_irq() helper for *other* IRQ
consumers.
If another device tree node tries to flag the same IRQ
for use as something else than rising edge, the kernel
irqdomain core will protest like this:
type mismatch, failed to map hwirq-NN for <FOO>!
Which is what happens when the device tree defines two
contradictory flags for the same interrupt line.
To work around this and alleviate the problem, assign 0
as flag for the interrupts taken by the PM GPIO and MPP
drivers. This will lead to the flag being unset, and a
second consumer requesting rising, falling, both or level
interrupts will be respected. This is what the qcom-pm*.dtsi
files already do.
Switched to using the symbolic name IRQ_TYPE_NONE so that
we get this more readable.
Fixes: bce3604696 ("ARM: dts: apq8064: add pm8921 mpp support")
Fixes: 874443fe9e ("ARM: dts: apq8064: Add pm8921 mfd and its gpio node")
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Björn Andersson <bjorn.andersson@linaro.org>
Cc: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 72b4f6a5e9 upstream.
On x86_32, when an interrupt happens from kernel space, SS and SP aren't
pushed and the existing stack is used. So pt_regs is effectively two
words shorter, and the previous stack pointer is normally the memory
after the shortened pt_regs, aka '®s->sp'.
But in the rare case where the interrupt hits right after the stack
pointer has been changed to point to an empty stack, like for example
when call_on_stack() is used, the address immediately after the
shortened pt_regs is no longer on the stack. In that case, instead of
'®s->sp', the previous stack pointer should be retrieved from the
beginning of the current stack page.
kernel_stack_pointer() wants to do that, but it forgets to dereference
the pointer. So instead of returning a pointer to the previous stack,
it returns a pointer to the beginning of the current stack.
Note that it's probably outside of kernel_stack_pointer()'s scope to be
switching stacks at all. The x86_64 version of this function doesn't do
it, and it would be better for the caller to do it if necessary. But
that's a patch for another day. This just fixes the original intent.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Byungchul Park <byungchul.park@lge.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nilay Vaish <nilayvaish@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 0788aa6a23 ("x86: Prepare removal of previous_esp from i386 thread_info structure")
Link: http://lkml.kernel.org/r/472453d6e9f6a2d4ab16aaed4935f43117111566.1471535549.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a51fe083e upstream.
When a CPU is physically added to a system then the MADT table is not
updated.
If subsequently a kdump kernel is started on that physically added CPU then
the ACPI enumeration fails to provide the information for this CPU which is
now the boot CPU of the kdump kernel.
As a consequence, generic_processor_info() is not invoked for that CPU so
the number of enumerated processors is 0 and none of the initializations,
including the logical package id management, are performed.
We have code which relies on the correctness of the logical package map and
other information which is initialized via generic_processor_info().
Executing such code will result in undefined behaviour or kernel crashes.
This problem applies only to the kdump kernel because a normal kexec will
switch to the original boot CPU, which is enumerated in MADT, before
jumping into the kexec kernel.
The boot code already has a check for num_processors equal 0 in
prefill_possible_map(). We can use that check as an indicator that the
enumeration of the boot CPU did not happen and invoke generic_processor_info()
for it. That initializes the relevant data for the boot CPU and therefore
prevents subsequent failure.
[ tglx: Refined the code and rewrote the changelog ]
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Fixes: 1f12e32f4c ("x86/topology: Create logical package id")
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Len Brown <len.brown@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: dyoung@redhat.com
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: kexec@lists.infradead.org
Link: http://lkml.kernel.org/r/1475514432-27682-1-git-send-email-prarit@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cff9ab2b29 upstream.
The array has a size of MAX_LOCAL_APIC, which can be as large as 32k, so it
can consume up to 128k.
The array has been there forever and was never used for anything useful
other than a version mismatch check which was introduced in 2009.
There is no reason to store the version in an array. The kernel is not
prepared to handle different APIC versions anyway, so the real important
part is to detect a version mismatch and warn about it, which can be done
with a single variable as well.
[ tglx: Massaged changelog ]
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: Andy Lutomirski <luto@amacapital.net>
CC: Borislav Petkov <bp@alien8.de>
CC: Brian Gerst <brgerst@gmail.com>
CC: Mike Travis <travis@sgi.com>
Link: http://lkml.kernel.org/r/20160913181232.30815-1-dvlasenk@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d4b05923f5 upstream.
Our XSAVE features are divided into two categories: those that
generate FPU exceptions, and those that do not. MPX and pkeys do
not generate FPU exceptions and thus can not be used lazily. We
disable them when lazy mode is forced on.
We have a pair of masks to collect these two sets of features, but
XFEATURE_MASK_PKRU was added to the wrong mask: XFEATURE_MASK_LAZY.
Fix it by moving the feature to XFEATURE_MASK_EAGER.
Note: this only causes problem if you boot with lazy FPU mode
(eagerfpu=off) which is *not* the default. It also only affects
hardware which is not currently publicly available. It looks like
eager mode is going away, but we still need this patch applied
to any kernel that has protection keys and lazy mode, which is 4.6
through 4.8 at this point, and 4.9 if the lazy removal isn't sent
to Linus for 4.9.
Fixes: c8df400984 ("x86/fpu, x86/mm/pkeys: Add PKRU xsave fields and data structures")
Signed-off-by: Dave Hansen <dave.hansen@intel.com>
Cc: Dave Hansen <dave@sr71.net>
Link: http://lkml.kernel.org/r/20161007162342.28A49813@viggo.jf.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit db91aa793f upstream.
When a CPU is about to be offlined we call fixup_irqs() that resets IRQ
affinities related to the CPU in question. The same thing is also done when
the system is suspended to S-states like S3 (mem).
For each IRQ we try to complete any on-going move regardless whether the
IRQ is actually part of x86_vector_domain. For each IRQ descriptor we fetch
its chip_data, assume it is of type struct apic_chip_data and manipulate it
by clearing old_domain mask etc. For irq_chips that are not part of the
x86_vector_domain, like those created by various GPIO drivers, will find
their chip_data being changed unexpectly.
Below is an example where GPIO chip owned by pinctrl-sunrisepoint.c gets
corrupted after resume:
# cat /sys/kernel/debug/gpio
gpiochip0: GPIOs 360-511, parent: platform/INT344B:00, INT344B:00:
gpio-511 ( |sysfs ) in hi
# rtcwake -s10 -mmem
<10 seconds passes>
# cat /sys/kernel/debug/gpio
gpiochip0: GPIOs 360-511, parent: platform/INT344B:00, INT344B:00:
gpio-511 ( |sysfs ) in ?
Note '?' in the output. It means the struct gpio_chip ->get function is
NULL whereas before suspend it was there.
Fix this by first checking that the IRQ belongs to x86_vector_domain before
we try to use the chip_data as struct apic_chip_data.
Reported-and-tested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: http://lkml.kernel.org/r/20161003101708.34795-1-mika.westerberg@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5e7307d9d upstream.
In some places, dump_backtrace() is called with a NULL tsk parameter,
e.g. in bug_handler() in arch/arm64, or indirectly via show_stack() in
core code. The expectation is that this is treated as if current were
passed instead of NULL. Similar is true of unwind_frame().
Commit a80a0eb70c ("arm64: make irq_stack_ptr more robust") didn't
take this into account. In dump_backtrace() it compares tsk against
current *before* we check if tsk is NULL, and in unwind_frame() we never
set tsk if it is NULL.
Due to this, we won't initialise irq_stack_ptr in either function. In
dump_backtrace() this results in calling dump_mem() for memory
immediately above the IRQ stack range, rather than for the relevant
range on the task stack. In unwind_frame we'll reject unwinding frames
on the IRQ stack.
In either case this results in incomplete or misleading backtrace
information, but is not otherwise problematic. The initial percpu areas
(including the IRQ stacks) are allocated in the linear map, and dump_mem
uses __get_user(), so we shouldn't access anything with side-effects,
and will handle holes safely.
This patch fixes the issue by having both functions handle the NULL tsk
case before doing anything else with tsk.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Fixes: a80a0eb70c ("arm64: make irq_stack_ptr more robust")
Acked-by: James Morse <james.morse@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yang Shi <yang.shi@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ac0e89bb47 upstream.
We use logical negate where bitwise negate was intended. It means that
we never return -EINVAL here.
Fixes: ce11e48b7f ('KVM: PPC: E500: Add userspace debug stub support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0099b7701f upstream.
If the vgic hasn't been created and initialized, we shouldn't attempt to
look at its data structures or flush/sync anything to the GIC hardware.
This fixes an issue reported by Alexander Graf when using a userspace
irqchip.
Fixes: 0919e84c0f ("KVM: arm/arm64: vgic-new: Add IRQ sync/flush framework")
Reported-by: Alexander Graf <agraf@suse.de>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6fe407f2d1 upstream.
If userspace creates a PMU for the VCPU, but doesn't create an in-kernel
irqchip, then we end up in a nasty path where we try to take an
uninitialized spinlock, which can lead to all sorts of breakages.
Luckily, QEMU always creates the VGIC before the PMU, so we can
establish this as ABI and check for the VGIC in the PMU init stage.
This can be relaxed at a later time if we want to support PMU with a
userspace irqchip.
Cc: Shannon Zhao <shannon.zhao@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 91e4f1b607 upstream.
When a guest TLB entry is replaced by TLBWI or TLBWR, we only invalidate
TLB entries on the local CPU. This doesn't work correctly on an SMP host
when the guest is migrated to a different physical CPU, as it could pick
up stale TLB mappings from the last time the vCPU ran on that physical
CPU.
Therefore invalidate both user and kernel host ASIDs on other CPUs,
which will cause new ASIDs to be generated when it next runs on those
CPUs.
We're careful only to do this if the TLB entry was already valid, and
only for the kernel ASID where the virtual address it mapped is outside
of the guest user address range.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fa73c3b25b upstream.
The MMCR2 register is available twice, one time with number 785
(privileged access), and one time with number 769 (unprivileged,
but it can be disabled completely). In former times, the Linux
kernel was using the unprivileged register 769 only, but since
commit 8dd75ccb57 ("powerpc: Use privileged SPR number
for MMCR2"), it uses the privileged register 785 instead.
The KVM-PR code then of course also switched to use the SPR 785,
but this is causing older guest kernels to crash, since these
kernels still access 769 instead. So to support older kernels
with KVM-PR again, we have to support register 769 in KVM-PR, too.
Fixes: 8dd75ccb57
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a6a198bc60 upstream.
Early during boot topology_update_package_map() computes
logical_pkg_ids for all present processors.
Later, when processors are brought up, identify_cpu() updates
these values based on phys_pkg_id which is a function of
initial_apicid. On PV guests the latter may point to a
non-existing node, causing logical_pkg_ids to be set to -1.
Intel's RAPL uses logical_pkg_id (as topology_logical_package_id())
to index its arrays and therefore in this case will point to index
65535 (since logical_pkg_id is a u16). This could lead to either a
crash or may actually access random memory location.
As a workaround, we recompute topology during CPU bringup to reset
logical_pkg_id to a valid value.
(The reason for initial_apicid being bogus is because it is
initial_apicid of the processor from which the guest is launched.
This value is CPUID(1).EBX[31:24])
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 88003fb10f upstream.
This fixes a compile failure:
drivers/built-in.o: In function `wm8350_i2c_probe':
core.c:(.text+0x828b0): undefined reference to `__devm_regmap_init_i2c'
Makefile:953: recipe for target 'vmlinux' failed
Fixes: 52b461b86a ("mfd: Add regmap cache support for wm8350")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a6dc64451 upstream.
set_bit() and clear_bit() take the bit number so this code is really
doing "1 << (1 << irq)" which is a double shift bug. It's done
consistently so it won't cause a problem unless "irq" is more than 4.
Fixes: 70c6cce040 ('mfd: Support 88pm80x in 80x driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c2469bc03 upstream.
readl_poll_timeout() calls usleep_range(), but
regmap_atmel_hlcdc_reg_write() is called in atomic context (regmap
spinlock held).
Replace the readl_poll_timeout() call by readl_poll_timeout_atomic().
Fixes: ea31c0cf9b ("mfd: atmel-hlcdc: Implement config synchronization")
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8dcc5ff8fc upstream.
Member "status" of struct usb_sg_request is managed by usb core. A
spin lock is used to serialize the change of it. The driver could
check the value of req->status, but should avoid changing it without
the hold of the spinlock. Otherwise, it could cause race or error
in usb core.
This patch could be backported to stable kernels with version later
than v3.14.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8da08ca03b upstream.
Currently, usb-line6 module exports an array of MIDI manufacturer ID and
usb-pod module uses it. However, the declaration is not the definition in
common header. The difference is explicit length of array. Although
compiler calculates it and everything goes well, it's better to use the
same representation between definition and declaration.
This commit fills the length of array for usb-line6 module. As a small
good sub-effect, this commit suppress below warnings from static analysis
by sparse v0.5.0.
sound/usb/line6/driver.c:274:43: error: cannot size expression
sound/usb/line6/driver.c:275:16: error: cannot size expression
sound/usb/line6/driver.c:276:16: error: cannot size expression
sound/usb/line6/driver.c:277:16: error: cannot size expression
Fixes: 705ececd1c ("Staging: add line6 usb driver")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eb1a74b7be upstream.
The DragonFly quirk added in 42e3121d90 ("ALSA: usb-audio: Add a more
accurate volume quirk for AudioQuest DragonFly") applies a custom dB map
on the volume control when its range is reported as 0..50 (0 .. 0.2dB).
However, there exists at least one other variant (hw v1.0c, as opposed
to the tested v1.2) which reports a different non-sensical volume range
(0..53) and the custom map is therefore not applied for that device.
This results in all of the volume change appearing close to 100% on
mixer UIs that utilize the dB TLV information.
Add a fallback case where no dB TLV is reported at all if the control
range is not 0..50 but still 0..N where N <= 1000 (3.9 dB). Also
restrict the quirk to only apply to the volume control as there is also
a mute control which would match the check otherwise.
Fixes: 42e3121d90 ("ALSA: usb-audio: Add a more accurate volume quirk for AudioQuest DragonFly")
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Reported-by: David W <regulars@d-dub.org.uk>
Tested-by: David W <regulars@d-dub.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit db68577966 upstream.
The pointer callbacks of ali5451 driver may return the value at the
boundary occasionally, and it results in the kernel warning like
snd_ali5451 0000:00:06.0: BUG: , pos = 16384, buffer size = 16384, period size = 1024
It seems that folding the position offset is enough for fixing the
warning and no ill-effect has been seen by that.
Reported-by: Enrico Mioso <mrkiko.rs@gmail.com>
Tested-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e6c88d28c upstream.
Commit 50c763f8c1 ("usb: dwc3: Set the ClearPendIN bit on Clear
Stall EP command") sets ClearPendIN bit for all IN endpoints of
v2.60a+ cores. This causes ClearStall command fails on 2.60+ cores
operating in HighSpeed mode.
In page 539 of 2.60a specification:
"When issuing Clear Stall command for IN endpoints in SuperSpeed
mode, the software must set the "ClearPendIN" bit to '1' to
clear any pending IN transcations, so that the device does not
expect any ACK TP from the host for the data sent earlier."
It's obvious that we only need to apply this rule to those IN
endpoints that currently operating in SuperSpeed mode.
Fixes: 50c763f8c1 ("usb: dwc3: Set the ClearPendIN bit on Clear Stall EP command")
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f38a8b9a4 upstream.
When cxl removes a vPHB, it's possible that the pci_controller may be freed
before all references to the devices on the vPHB have been released. This
in turn causes an invalid memory access when the devices are eventually
released, as pcibios_release_device() attempts to call the phb's
release_device hook.
In cxl_pci_vphb_remove(), remove the existing call to
pcibios_free_controller(). Instead, use
pcibios_free_controller_deferred() to free the pci_controller after all
devices have been released. Export pci_set_host_bridge_release() so we can
do this.
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2dd9c11b9d upstream.
This patch leverages 'struct pci_host_bridge' from the PCI subsystem
in order to free the pci_controller only after the last reference to
its devices is dropped (avoiding an oops in pcibios_release_device()
if the last reference is dropped after pcibios_free_controller()).
The patch relies on pci_host_bridge.release_fn() (and .release_data),
which is called automatically by the PCI subsystem when the root bus
is released (i.e., the last reference is dropped). Those fields are
set via pci_set_host_bridge_release() (e.g. in the platform-specific
implementation of pcibios_root_bridge_prepare()).
It introduces the 'pcibios_free_controller_deferred()' .release_fn()
and it expects .release_data to hold a pointer to the pci_controller.
The function implictly calls 'pcibios_free_controller()', so an user
must *NOT* explicitly call it if using the new _deferred() callback.
The functionality is enabled for pseries (although it isn't platform
specific, and may be used by cxl).
Details on not-so-elegant design choices:
- Use 'pci_host_bridge.release_data' field as pointer to associated
'struct pci_controller' so *not* to 'pci_bus_to_host(bridge->bus)'
in pcibios_free_controller_deferred().
That's because pci_remove_root_bus() sets 'host_bridge->bus = NULL'
(so, if the last reference is released after pci_remove_root_bus()
runs, which eventually reaches pcibios_free_controller_deferred(),
that would hit a null pointer dereference).
The cxl/vphb.c code calls pci_remove_root_bus(), and the cxl folks
are interested in this fix.
Test-case #1 (hold references)
# ls -ld /sys/block/sd* | grep -m1 0021:01:00.0
<...> /sys/block/sdaa -> ../devices/pci0021:01/0021:01:00.0/<...>
# ls -ld /sys/block/sd* | grep -m1 0021:01:00.1
<...> /sys/block/sdab -> ../devices/pci0021:01/0021:01:00.1/<...>
# cat >/dev/sdaa & pid1=$!
# cat >/dev/sdab & pid2=$!
# drmgr -w 5 -d 1 -c phb -s 'PHB 33' -r
Validating PHB DLPAR capability...yes.
[ 594.306719] pci_hp_remove_devices: PCI: Removing devices on bus 0021:01
[ 594.306738] pci_hp_remove_devices: Removing 0021:01:00.0...
...
[ 598.236381] pci_hp_remove_devices: Removing 0021:01:00.1...
...
[ 611.972077] pci_bus 0021:01: busn_res: [bus 01-ff] is released
[ 611.972140] rpadlpar_io: slot PHB 33 removed
# kill -9 $pid1
# kill -9 $pid2
[ 632.918088] pcibios_free_controller_deferred: domain 33, dynamic 1
Test-case #2 (don't hold references)
# drmgr -w 5 -d 1 -c phb -s 'PHB 33' -r
Validating PHB DLPAR capability...yes.
[ 916.357363] pci_hp_remove_devices: PCI: Removing devices on bus 0021:01
[ 916.357386] pci_hp_remove_devices: Removing 0021:01:00.0...
...
[ 920.566527] pci_hp_remove_devices: Removing 0021:01:00.1...
...
[ 933.955873] pci_bus 0021:01: busn_res: [bus 01-ff] is released
[ 933.955977] pcibios_free_controller_deferred: domain 33, dynamic 1
[ 933.955999] rpadlpar_io: slot PHB 33 removed
Suggested-By: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Tested-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com> # cxl
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0eec880966 upstream.
HP Spectre x360 with CX20724 codec has two speaker outputs while the
BIOS sets up only the bottom one (NID 0x17) and disables the top one
(NID 0x1d).
This patch adds a fixup simply defining the proper pincfg for NID 0x1d
so that the top speaker works as is.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=169071
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f640970a4 upstream.
One of the laptops has the codec ALC256 on it, applying the
ALC255_FIXUP_DELL1_MIC_NO_PRESENCE can fix the problem, the rest
of laptops have the codec ALC295 on them, they are similar to machines
with ALC225, applying the ALC269_FIXUP_DELL1_MIC_NO_PRESENCE can fix
the problem.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 392c9da24a upstream.
We have two new Dell laptop models, they have the same ALC255 pin
definition, but not in the pin quirk table yet, as a result, the
headset microphone can't work. After adding the definition in the
table, the headset microphone works well.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ab21b63e8a upstream.
This reverts commit e6c7efdcb7.
Turns out it was totally wrong. The memory is supposed to be bound to
the kref, as the original code was doing correctly, not the
device/driver binding as the devm_kzalloc() would cause.
This fixes an oops when read would be called after the device was
unbound from the driver.
Reported-by: Ladislav Michl <ladis@linux-mips.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 238b7bd91b upstream.
In v_recv_cmd_submit(), urb_p->urb->pipe has the type unsigned int
(which is 32-bit long on x86_64) but 11<<30 results in a 34-bit integer.
Therefore the 2 leading bits are truncated and
urb_p->urb->pipe &= ~(11 << 30);
has the same meaning as
urb_p->urb->pipe &= ~(3 << 30);
This second statement seems to be how the code was intended to be
written, as PIPE_ constants have values between 0 and 3.
The overflow has been detected with a clang warning:
drivers/usb/usbip/vudc_rx.c:145:27: warning: signed shift result
(0x2C0000000) requires 35 bits to represent, but 'int' only has 32
bits [-Wshift-overflow]
urb_p->urb->pipe &= ~(11 << 30);
~~ ^ ~~
Fixes: 79c02cb1fd ("usbip: vudc: Add vudc_rx")
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc1e2c8ea8 upstream.
Commit 367e8560e8 introduced a bug
in fbtft-core where fps is always 0, this is because variable
update_time is not assigned correctly.
Signed-off-by: Ksenija Stanojevic <ksenija.stanojevic@gmail.com>
Fixes: 367e8560e8 ("Staging: fbtbt: Replace timespec with ktime_t")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2fae9e5a7b upstream.
This patch fixes a NULL pointer dereference caused by a race codition in
the probe function of the legousbtower driver. It re-structures the
probe function to only register the interface after successfully reading
the board's firmware ID.
The probe function does not deregister the usb interface after an error
receiving the devices firmware ID. The device file registered
(/dev/usb/legousbtower%d) may be read/written globally before the probe
function returns. When tower_delete is called in the probe function
(after an r/w has been initiated), core dev structures are deleted while
the file operation functions are still running. If the 0 address is
mappable on the machine, this vulnerability can be used to create a
Local Priviege Escalation exploit via a write-what-where condition by
remapping dev->interrupt_out_buffer in tower_write. A forged USB device
and local program execution would be required for LPE. The USB device
would have to delay the control message in tower_probe and accept
the control urb in tower_open whilst guest code initiated a write to the
device file as tower_delete is called from the error in tower_probe.
This bug has existed since 2003. Patch tested by emulated device.
Reported-by: James Patrick-Evans <james@jmp-e.com>
Tested-by: James Patrick-Evans <james@jmp-e.com>
Signed-off-by: James Patrick-Evans <james@jmp-e.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7efb367320 upstream.
bio_alloc() can allocate a bio with at most BIO_MAX_PAGES (256) vector
entries. However, the incoming bio may have more vector entries if it
was allocated by other means. For example, bcache submits bios with
more than BIO_MAX_PAGES entries. This results in bio_alloc() failure.
To avoid the failure, change the code so that it allocates bio with at
most BIO_MAX_PAGES entries. If the incoming bio has more entries,
bio_add_page() will fail and a new bio will be allocated - the code that
handles bio_add_page() failure already exists in the dm-log-writes
target.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 22f6b4d34f upstream.
This ensures that do_mmap() won't implicitly make AIO memory mappings
executable if the READ_IMPLIES_EXEC personality flag is set. Such
behavior is problematic because the security_mmap_file LSM hook doesn't
catch this case, potentially permitting an attacker to bypass a W^X
policy enforced by SELinux.
I have tested the patch on my machine.
To test the behavior, compile and run this:
#define _GNU_SOURCE
#include <unistd.h>
#include <sys/personality.h>
#include <linux/aio_abi.h>
#include <err.h>
#include <stdlib.h>
#include <stdio.h>
#include <sys/syscall.h>
int main(void) {
personality(READ_IMPLIES_EXEC);
aio_context_t ctx = 0;
if (syscall(__NR_io_setup, 1, &ctx))
err(1, "io_setup");
char cmd[1000];
sprintf(cmd, "cat /proc/%d/maps | grep -F '/[aio]'",
(int)getpid());
system(cmd);
return 0;
}
In the output, "rw-s" is good, "rwxs" is bad.
Signed-off-by: Jann Horn <jann@thejh.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 422eac3f7d upstream.
On my Lenovo x250 the following situation occurs:
[18697.813871] tpm_crb MSFT0101:00: can't request region for resource
[mem 0xacdff080-0xacdfffff]
The mapping of the control area overlaps the mapping of the command
buffer. The control area is mapped over page, which is not right. It
should mapped over sizeof(struct crb_control_area).
Fixing this issue unmasks another issue. Command and response buffers
can overlap and they do interleave on this machine. According to the PTP
specification the overlapping means that they are mapped to the same
buffer.
The commit has been also on a Haswell NUC where things worked before
applying this fix so that the both code paths for response buffer
initialization are tested.
Cc: stable@vger.kernel.org
Fixes: 1bd047be37 ("tpm_crb: Use devm_ioremap_resource")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 14ddfbf488 upstream.
The iomem resource is needed only temporarily so it is better to pass
it on instead of storing it permanently. Named the variable as io_res
so that the code better documents itself.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7fae6655a0 upstream.
MAD_IFC command is supported only for physical functions (PF)
and when physical port is IB. The proposed fix enforces it.
Fixes: d603c809ef ("IB/mlx5: Fix decision on using MAD_IFC")
Reported-by: David Chang <dchang@suse.com>
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ec07bf8a8 upstream.
When sending QP1 MAD packets which use a GRH, the source GID
(which consists of the 64-bit subnet prefix, and the 64 bit port GUID)
must be included in the packet GRH.
For SR-IOV, a GID cache is used, since the source GID needs to be the
slave's source GID, and not the Hypervisor's GID. This cache also
included a subnet_prefix. Unfortunately, the subnet_prefix field in
the cache was never initialized (to the default subnet prefix 0xfe80::0).
As a result, this field remained all zeroes. Therefore, when SR-IOV
was active, all QP1 packets which included a GRH had a source GID
subnet prefix of all-zeroes.
However, the subnet-prefix should initially be 0xfe80::0 (the default
subnet prefix). In addition, if OpenSM modifies a port's subnet prefix,
the new subnet prefix must be used in the GRH when sending QP1 packets.
To fix this we now initialize the subnet prefix in the SR-IOV GID cache
to the default subnet prefix. We update the cached value if/when OpenSM
modifies the port's subnet prefix. We take this cached value when sending
QP1 packets when SR-IOV is active.
Note that the value is stored as an atomic64. This eliminates any need
for locking when the subnet prefix is being updated.
Note also that we depend on the FW generating the "port management change"
event for tracking subnet-prefix changes performed by OpenSM. If running
early FW (before 2.9.4630), subnet prefix changes will not be tracked (but
the default subnet prefix still will be stored in the cache; therefore
users who do not modify the subnet prefix will not have a problem).
IF there is a need for such tracking also for early FW, we will add that
capability in a subsequent patch.
Fixes: 1ffeb2eb8b ("IB/mlx4: SR-IOV IB context objects and proxy/tunnel SQP support")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit baa0be7026 upstream.
The indentation in the QP1 GRH flow in procedure build_mlx_header is
really confusing. Fix it, in preparation for a commit which touches
this code.
Fixes: 1ffeb2eb8b ("IB/mlx4: SR-IOV IB context objects and proxy/tunnel SQP support")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e5ac40cd66 upstream.
Because of an incorrect bit-masking done on the join state bits, when
handling a join request we failed to detect a difference between the
group join state and the request join state when joining as send only
full member (0x8). This caused the MC join request not to be sent.
This issue is relevant only when SRIOV is enabled and SM supports
send only full member.
This fix separates scope bits and join states bits a nibble each.
Fixes: b9c5d6a643 ('IB/mlx4: Add multicast group (MCG) paravirtualization for SR-IOV')
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 344bacca8c upstream.
This fix solves a race between light flush and on the fly joins.
Light flush doesn't set the device to down and unset IPOIB_OPER_UP
flag, this means that if while flushing we have a MC join in progress
and the QP was attached to BC MGID we can have a mismatches when
re-attaching a QP to the BC MGID.
The light flush would set the broadcast group to NULL causing an on
the fly join to rejoin and reattach to the BC MCG as well as adding
the BC MGID to the multicast list. The flush process would later on
remove the BC MGID and detach it from the QP. On the next flush
the BC MGID is present in the multicast list but not found when trying
to detach it because of the previous double attach and single detach.
[18332.714265] ------------[ cut here ]------------
[18332.717775] WARNING: CPU: 6 PID: 3767 at drivers/infiniband/core/verbs.c:280 ib_dealloc_pd+0xff/0x120 [ib_core]
...
[18332.775198] Hardware name: Red Hat KVM, BIOS Bochs 01/01/2011
[18332.779411] 0000000000000000 ffff8800b50dfbb0 ffffffff813fed47 0000000000000000
[18332.784960] 0000000000000000 ffff8800b50dfbf0 ffffffff8109add1 0000011832f58300
[18332.790547] ffff880226a596c0 ffff880032482000 ffff880032482830 ffff880226a59280
[18332.796199] Call Trace:
[18332.798015] [<ffffffff813fed47>] dump_stack+0x63/0x8c
[18332.801831] [<ffffffff8109add1>] __warn+0xd1/0xf0
[18332.805403] [<ffffffff8109aebd>] warn_slowpath_null+0x1d/0x20
[18332.809706] [<ffffffffa025d90f>] ib_dealloc_pd+0xff/0x120 [ib_core]
[18332.814384] [<ffffffffa04f3d7c>] ipoib_transport_dev_cleanup+0xfc/0x1d0 [ib_ipoib]
[18332.820031] [<ffffffffa04ed648>] ipoib_ib_dev_cleanup+0x98/0x110 [ib_ipoib]
[18332.825220] [<ffffffffa04e62c8>] ipoib_dev_cleanup+0x2d8/0x550 [ib_ipoib]
[18332.830290] [<ffffffffa04e656f>] ipoib_uninit+0x2f/0x40 [ib_ipoib]
[18332.834911] [<ffffffff81772a8a>] rollback_registered_many+0x1aa/0x2c0
[18332.839741] [<ffffffff81772bd1>] rollback_registered+0x31/0x40
[18332.844091] [<ffffffff81773b18>] unregister_netdevice_queue+0x48/0x80
[18332.848880] [<ffffffffa04f489b>] ipoib_vlan_delete+0x1fb/0x290 [ib_ipoib]
[18332.853848] [<ffffffffa04df1cd>] delete_child+0x7d/0xf0 [ib_ipoib]
[18332.858474] [<ffffffff81520c08>] dev_attr_store+0x18/0x30
[18332.862510] [<ffffffff8127fe4a>] sysfs_kf_write+0x3a/0x50
[18332.866349] [<ffffffff8127f4e0>] kernfs_fop_write+0x120/0x170
[18332.870471] [<ffffffff81207198>] __vfs_write+0x28/0xe0
[18332.874152] [<ffffffff810e09bf>] ? percpu_down_read+0x1f/0x50
[18332.878274] [<ffffffff81208062>] vfs_write+0xa2/0x1a0
[18332.881896] [<ffffffff812093a6>] SyS_write+0x46/0xa0
[18332.885632] [<ffffffff810039b7>] do_syscall_64+0x57/0xb0
[18332.889709] [<ffffffff81883321>] entry_SYSCALL64_slow_path+0x25/0x25
[18332.894727] ---[ end trace 09ebbe31f831ef17 ]---
Fixes: ee1e2c82c2 ("IPoIB: Refresh paths instead of flushing them on SM change events")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 835831c57e upstream.
Use scsi_is_sas_rphy() instead of is_sas_attached() to decide whether we
should obtain the SAS address from a scsi device or not. This will
prevent us from tripping on the BUG_ON() in sas_sdev_to_rdev() if the
rphy isn't attached to the SAS transport class, like it is with hpsa's
logical devices.
Fixes: 3f8d6f2a0 ('ses: fix discovery of SATA devices in SAS enclosures')
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1bc8da4e14 upstream.
When searching for a suitable node that should be used for inserting a new
register, which does not fall within the range of any existing node, we not
only looks for nodes which are directly adjacent to the new register, but
for nodes within a certain proximity. This is done to avoid creating lots
of small nodes with just a few registers spacing in between, which would
increase memory usage as well as tree traversal time.
This means there might be multiple node candidates which fall within the
proximity range of the new register. If we choose the first node we
encounter, under certain register insertion patterns it is possible to end
up with overlapping ranges. This will break order in the rbtree and can
cause the cached register value to become corrupted.
E.g. take the simplified example where the proximity range is 2 and the
register insertion sequence is 1, 4, 2, 3, 5.
* Insert of register 1 creates a new node, this is the root of the rbtree
* Insert of register 4 creates a new node, which is inserted to the right
of the root.
* Insert of register 2 gets inserted to the first node
* Insert of register 3 gets inserted to the first node
* Insert of register 5 also gets inserted into the first node since
this is the first node encountered and it is within the proximity range.
Now there are two overlapping nodes.
To avoid this always choose the node that is closest to the new register.
This will ensure that nodes will not overlap. The tree traversal is still
done as a binary search, we just don't stop at the first node found. So the
complexity of the algorithm stays within the same order.
Ideally if a new register is in the range of two adjacent blocks those
blocks should be merged, but that is a much more invasive change and left
for later.
The issue was initially introduced in commit 472fdec738 ("regmap: rbtree:
Reduce number of nodes, take 2"), but became much more exposed by commit
6399aea629 ("regmap: rbtree: When adding a reg do a bsearch for target
node") which changed the order in which nodes are looked-up.
Fixes: 6399aea629 ("regmap: rbtree: When adding a reg do a bsearch for target node")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 68c6bcdd8b upstream.
The function send_leave sets the member: group->query_id
(group->query_id = ret) after calling the sa_query, but leave_handler
can be executed before the setting and it might delete the group object,
and will get a memory corruption.
Additionally, this patch gets rid of group->query_id variable which is
not used.
Fixes: faec2f7b96 ('IB/sa: Track multicast join/leave requests')
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 546481c281 upstream.
When a new CM connection is being requested, ipoib driver copies data
from the path pointer in the CM/tx object, the path object might be
invalid at the point and memory corruption will happened later when now
the CM driver will try using that data.
The next scenario demonstrates it:
neigh_add_path --> ipoib_cm_create_tx -->
queue_work (pointer to path is in the cm/tx struct)
#while the work is still in the queue,
#the port goes down and causes the ipoib_flush_paths:
ipoib_flush_paths --> path_free --> kfree(path)
#at this point the work scheduled starts.
ipoib_cm_tx_start --> copy from the (invalid)path pointer:
(memcpy(&pathrec, &p->path->pathrec, sizeof pathrec);)
-> memory corruption.
To fix that the driver now starts the CM/tx connection only if that
specific path exists in the general paths database.
This check is protected with the relevant locks, and uses the gid from
the neigh member in the CM/tx object which is valid according to the ref
count that was taken by the CM/tx.
Fixes: 839fcaba35 ('IPoIB: Connected mode experimental support')
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f5aa88a7b upstream.
Commit f3c4ebe65e ("ceph: using hash value to compose dentry offset")
modified "if (fpos_frag(new_pos) != fi->frag)" to "if (fi->frag |=
fpos_frag(new_pos))" in need_reset_readdir(), thus replacing a
comparison operator with an assignment one.
This looks like a typo which is reported by clang when building the
kernel with some warning flags:
fs/ceph/dir.c:600:22: error: using the result of an assignment as a
condition without parentheses [-Werror,-Wparentheses]
} else if (fi->frag |= fpos_frag(new_pos)) {
~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~
fs/ceph/dir.c:600:22: note: place parentheses around the assignment
to silence this warning
} else if (fi->frag |= fpos_frag(new_pos)) {
^
( )
fs/ceph/dir.c:600:22: note: use '!=' to turn this compound
assignment into an inequality comparison
} else if (fi->frag |= fpos_frag(new_pos)) {
^~
!=
Fixes: f3c4ebe65e ("ceph: using hash value to compose dentry offset")
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dccbfcf52c upstream.
If vmcs12 does not intercept APIC_BASE writes, then KVM will handle the
write with vmcs02 as the current VMCS.
This will incorrectly apply modifications intended for vmcs01 to vmcs02
and L2 can use it to gain access to L0's x2APIC registers by disabling
virtualized x2APIC while using msr bitmap that assumes enabled.
Postpone execution of vmx_set_virtual_x2apic_mode until vmcs01 is the
current VMCS. An alternative solution would temporarily make vmcs01 the
current VMCS, but it requires more care.
Fixes: 8d14695f95 ("x86, apicv: add virtual x2apic support")
Reported-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6a8b0c6b18 upstream.
free_irq() expects the same device identity that was passed to
corresponding request_irq(), otherwise the IRQ is not freed.
Fixes: e1f7c9eee7 ("dmaengine: at_xdmac: creation of the atmel eXtended DMA Controller driver")
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e6173ba42b upstream.
Some versions of gcc don't like tests for the value of an undefined
preprocessor symbol, even in the #else branch of an #ifndef:
lib/test_hash.c:224:7: warning: "HAVE_ARCH__HASH_32" is not defined [-Wundef]
#elif HAVE_ARCH__HASH_32 != 1
^
lib/test_hash.c:229:7: warning: "HAVE_ARCH_HASH_32" is not defined [-Wundef]
#elif HAVE_ARCH_HASH_32 != 1
^
lib/test_hash.c:234:7: warning: "HAVE_ARCH_HASH_64" is not defined [-Wundef]
#elif HAVE_ARCH_HASH_64 != 1
^
Seen with gcc 4.9, not seen with 4.1.2.
Change the logic to only check the value inside an #ifdef to fix this.
Fixes: 468a942852 ("<linux/hash.h>: Add support for architecture-specific functions")
Link: http://lkml.kernel.org/r/20160829214952.1334674-4-arnd@arndb.de
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: George Spelvin <linux@sciencehorizons.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c8d477a77 upstream.
Putting the periodicity timer in the mirror instances is causing
non-scalable reporting behaviour and missed reporting intervals.
When you recall layouts and/or implement client side mirroring, it
leads to consecutive reports with only a few ms between RPC calls.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Fixes: d0379a5d06 ("pNFS/flexfiles: Support server-supplied...")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 16590a2281 upstream.
Using NFSv4.1 on RDMA should be safe, so broaden the new checks in
rpc_create().
WARN_ON_ONCE is used, matching most other WARN call sites in clnt.c.
Fixes: 39a9beab5a ("rpc: share one xps between all backchannels")
Fixes: d50039ea5e ("nfsd4/rpc: move backchannel create logic...")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: J. Bruce Fields <bfields@fieldses.org>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 735f2770a7 upstream.
Commit fec1d01152 ("[PATCH] Disable CLONE_CHILD_CLEARTID for abnormal
exit") has caused a subtle regression in nscd which uses
CLONE_CHILD_CLEARTID to clear the nscd_certainly_running flag in the
shared databases, so that the clients are notified when nscd is
restarted. Now, when nscd uses a non-persistent database, clients that
have it mapped keep thinking the database is being updated by nscd, when
in fact nscd has created a new (anonymous) one (for non-persistent
databases it uses an unlinked file as backend).
The original proposal for the CLONE_CHILD_CLEARTID change claimed
(https://lkml.org/lkml/2006/10/25/233):
: The NPTL library uses the CLONE_CHILD_CLEARTID flag on clone() syscalls
: on behalf of pthread_create() library calls. This feature is used to
: request that the kernel clear the thread-id in user space (at an address
: provided in the syscall) when the thread disassociates itself from the
: address space, which is done in mm_release().
:
: Unfortunately, when a multi-threaded process incurs a core dump (such as
: from a SIGSEGV), the core-dumping thread sends SIGKILL signals to all of
: the other threads, which then proceed to clear their user-space tids
: before synchronizing in exit_mm() with the start of core dumping. This
: misrepresents the state of process's address space at the time of the
: SIGSEGV and makes it more difficult for someone to debug NPTL and glibc
: problems (misleading him/her to conclude that the threads had gone away
: before the fault).
:
: The fix below is to simply avoid the CLONE_CHILD_CLEARTID action if a
: core dump has been initiated.
The resulting patch from Roland (https://lkml.org/lkml/2006/10/26/269)
seems to have a larger scope than the original patch asked for. It
seems that limitting the scope of the check to core dumping should work
for SIGSEGV issue describe above.
[Changelog partly based on Andreas' description]
Fixes: fec1d01152 ("[PATCH] Disable CLONE_CHILD_CLEARTID for abnormal exit")
Link: http://lkml.kernel.org/r/1471968749-26173-1-git-send-email-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Tested-by: William Preston <wpreston@suse.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Roland McGrath <roland@hack.frob.com>
Cc: Andreas Schwab <schwab@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23d70503ee upstream.
'work' and 'route->path_rec' are malloced in cma_resolve_iboe_route()
and should be freed before leaving from the error handling cases,
otherwise it will cause memory leak.
Fixes: 200298326b ('IB/core: Validate route when we init ah')
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Reviewed-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a871967068 upstream.
Fixes: ddd17531ad ("ASoC: omap-mcpdm: Clean up with devm_* function")
Managed irq request will not doing any good in ASoC probe level as it is
not going to free up the irq when the driver is unbound from the sound
card.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reported-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7d316a02f upstream.
We have scripts which write to certain fields on 3.18 kernels but this
seems to be failing on 4.4 kernels. An entry which we write to here is
xfrm_aevent_rseqth which is u32.
echo 4294967295 > /proc/sys/net/core/xfrm_aevent_rseqth
Commit 230633d109 ("kernel/sysctl.c: detect overflows when converting
to int") prevented writing to sysctl entries when integer overflow
occurs. However, this does not apply to unsigned integers.
Heinrich suggested that we introduce a new option to handle 64 bit
limits and set min as 0 and max as UINT_MAX. This might not work as it
leads to issues similar to __do_proc_doulongvec_minmax. Alternatively,
we would need to change the datatype of the entry to 64 bit.
static int __do_proc_doulongvec_minmax(void *data, struct ctl_table
{
i = (unsigned long *) data; //This cast is causing to read beyond the size of data (u32)
vleft = table->maxlen / sizeof(unsigned long); //vleft is 0 because maxlen is sizeof(u32) which is lesser than sizeof(unsigned long) on x86_64.
Introduce a new proc handler proc_douintvec. Individual proc entries
will need to be updated to use the new handler.
[akpm@linux-foundation.org: coding-style fixes]
Fixes: 230633d109 ("kernel/sysctl.c:detect overflows when converting to int")
Link: http://lkml.kernel.org/r/1471479806-5252-1-git-send-email-subashab@codeaurora.org
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Kees Cook <keescook@chromium.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66443efa83 upstream.
When booting from an OpenFirmware which supports it, we use the
"ibm,client-architecture-support" firmware call to communicate
our capabilities to firmware.
The format of the structure we pass to firmware is specified in
PAPR (Power Architecture Platform Requirements), or the public version
LoPAPR (Linux on Power Architecture Platform Reference).
Referring to table 244 in LoPAPR v1.1, option vector 5 contains a 4 byte
field at bytes 17-20 for the "Platform Facilities Enable". This is
followed by a 1 byte field at byte 21 for "Sub-Processor Represenation
Level".
Comparing to the code, there we have the Platform Facilities
options (OV5_PFO_*) at byte 17, but we fail to pad that field out to its
full width of 4 bytes. This means the OV5_SUB_PROCESSORS option is
incorrectly placed at byte 18.
Fix it by adding zero bytes for bytes 18, 19, 20, and comment the bytes
to hopefully make it clearer in future.
As far as I'm aware nothing actually consumes this value at this time,
so the effect of this bug is nil in practice.
It does mean we've been incorrectly setting bit 15 of the "Platform
Facilities Enable" option for the past ~3 1/2 years, so we should avoid
allocating that bit to anything else in future.
Fixes: df77c79920 ("powerpc/pseries: Update ibm,architecture.vec for PAPR 2.7/POWER8")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f823a2aa8f upstream.
wlc_phy_txpower_get_current() does a logical OR of power->flags, which
presumes that power.flags was initiliazed earlier by the caller,
unfortunately, this is not the case, so make sure we zero out the struct
tx_power before calling into wlc_phy_txpower_get_current().
Reported-by: coverity (CID 146011)
Fixes: 5b435de0d7 ("net: wireless: add brcm80211 drivers")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c5fa1f464 upstream.
In case dma_mapping_error() returns an error in dma_rxfill, we would be
leaking a packet that we allocated with brcmu_pkt_buf_get_skb().
Reported-by: coverity (CID 1081819)
Fixes: 67d0cf50bd ("brcmsmac: Fix WARNING caused by lack of calls to dma_mapping_error()")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3bdae81072 upstream.
In case brcmf_sdiod_recv_chain() cannot complete a succeful call to
brcmf_sdiod_buffrw, we would be leaking glom_skb and not free it as we
should, fix this.
Reported-by: coverity (CID 1164856)
Fixes: a413e39a38 ("brcmfmac: fix brcmf_sdcard_recv_chain() for host without sg support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 979cf59acc upstream.
Fix to return error code -ENODEV from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 87b2bdf022 ("ASoC: Intel: Skylake: Initialize NHLT table")
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Acked-By: Vinod Koul <vinod.kou@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 38f1932e60 upstream.
ib_unmap_fmr() takes a list of FMRs to unmap. However, it does not
remove the FMRs from this list as it processes them. Other
ib_unmap_fmr() call sites are careful to remove FMRs from the list
after ib_unmap_fmr() returns.
Since commit 7c7a5390dc ("xprtrdma: Add ro_unmap_sync method for FMR")
fmr_op_unmap_sync passes more than one FMR to ib_unmap_fmr(), but
it didn't bother to remove the FMRs from that list once the call was
complete.
I've noticed some instability that could be related to list
tangling by the new fmr_op_unmap_sync() logic. In an abundance
of caution, add some defensive logic to clean up properly after
ib_unmap_fmr().
Fixes: 7c7a5390dc ("xprtrdma: Add ro_unmap_sync method for FMR")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8fbaa51d43 upstream.
If kzalloc() fails when allocating adapter->guest in
cxl_guest_init_adapter(), we call free_adapter() before erroring out.
free_adapter() in turn attempts to dereference adapter->guest, which in
this case is NULL.
In free_adapter(), skip the adapter->guest cleanup if adapter->guest is
NULL.
Fixes: 14baf4d9c7 ("cxl: Add guest-specific code")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c10bbde10 upstream.
WDOG_HW_RUNNING indicates that the hardware watchdog is running while the
watchdog device is closed. The flag may be set by the driver when it is
instantiated to indicate that the watchdog is running, and that the
watchdog core needs to send heartbeat requests to the driver until the
watchdog device is opened.
When the watchdog device is closed, the flag can be used by the driver's
stop function to indicate to the watchdog core that it was unable to stop
the watchdog, and that the watchdog core needs to send heartbeat requests.
This only works if the flag is actually cleared when the watchdog is
stopped. To avoid having to clear the flag in each driver's stop function,
clear it in the watchdog core before calling the stop function.
Reported-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Fixes: ee142889e3 ("watchdog: Introduce WDOG_HW_RUNNING flag")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c001c87a63 upstream.
We should always do a layoutcommit after commit to DS, except if
the layout segment we're using has set FF_FLAGS_NO_LAYOUTCOMMIT.
Fixes: d67ae825a5 ("pnfs/flexfiles: Add the FlexFile Layout Driver")
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a4e187d83d upstream.
Before commit 778be232a2 ("NFS do not find client in NFSv4
pg_authenticate"), the Linux callback server replied with
RPC_AUTH_ERROR / RPC_AUTH_BADCRED, instead of dropping the CB
request. Let's restore that behavior so the server has a chance to
do something useful about it, and provide a warning that helps
admins correct the problem.
Fixes: 778be232a2 ("NFS do not find client in NFSv4 ...")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0533b13072 upstream.
If an RPC program does not set vs_dispatch and pc_func() returns
rpc_drop_reply, the server sends a reply anyway containing a single
word containing the value RPC_DROP_REPLY (in network byte-order, of
course). This is a nonsense RPC message.
Fixes: 9e701c6109 ("svcrpc: simpler request dropping")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca857cc1d4 upstream.
If a pNFS client sets hdr->pgio_done_cb, then we should not overwrite that
in nfs4_proc_read_setup()
Fixes: 75bf47ebf6 ("pNFS/flexfile: Fix erroneous fall back to...")
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4aa819c79b upstream.
When building this driver on arm64, we get a harmless type
mismatch warning:
drivers/dma/bcm2835-dma.c: In function 'bcm2835_dma_fill_cb_chain_with_sg':
include/linux/kernel.h:743:17: warning: comparison of distinct pointer types lacks a cast
(void) (&_min1 == &_min2); \
^
drivers/dma/bcm2835-dma.c:409:21: note: in expansion of macro 'min'
cb->cb->length = min(len, max_len);
This changes the type of the 'len' variable to size_t, which
avoids the problem.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 388cc7a281 ("dmaengine: bcm2835: add slave_sg support to bcm2835-dma")
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9ef3c51121 upstream.
tdev->signal is not set NULL after it's freed. This will cause random
exceptions when the stale pointer is accessed after tdev->signal is
freed. Also, since tdev->signal allocation is skipped the next time
it's written, this leads to continuous fault finally leading to the
total death of the system.
Fixes: d1c2f87c9a ("mailbox: mailbox-test: Prevent memory leak")
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aaab50fcea upstream.
The function ar9003_hw_apply_minccapwr_thresh takes as second parameter not
a pointer to the channel but a boolean value describing whether the channel
is 2.4GHz or not. This broke (according to the origin commit) the ETSI
regulatory compliance on 5GHz channels.
Fixes: 3533bf6b15 ("ath9k: Fix regulatory compliance")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Cc: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d7e92e15e9 upstream.
When CONFIG_INPUT is disabled, multiple gspca backend drivers
print compile-time warnings about unused variables:
media/usb/gspca/cpia1.c: In function 'sd_stopN':
media/usb/gspca/cpia1.c:1627:13: error: unused variable 'sd' [-Werror=unused-variable]
media/usb/gspca/konica.c: In function 'sd_stopN':
media/usb/gspca/konica.c:246:13: error: unused variable 'sd' [-Werror=unused-variable]
This annotates the variables as __maybe_unused, to let the compiler
know that they are declared intentionally.
Fixes: ee186fd96a ("[media] gscpa_t613: Add support for the camera button")
Fixes: c2f644aeeb ("[media] gspca_cpia1: Add support for button")
Fixes: b517af7228 ("V4L/DVB: gspca_konica: New gspca subdriver for konica chipset using cams")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d69e40fade upstream.
The vsp1_pipeline_reset() function loops over pipeline inputs and output
and resets them. When doing so it assumes both that the pipeline has
been correctly configured with an output, and that inputs are are stored
in the pipe inputs array at positions 0 to num_inputs-1.
Both the assumptions are incorrect. The pipeline might need to be reset
after a failed attempts to configure it, without any output specified.
Furthermore, inputs are stored in a positiong equal to their RPF index,
possibly creating holes in the inputs array if the RPFs are not used in
sequence.
Fix both issues by looping over the whole inputs array and skipping
unused entries, and ignoring the output when not set.
Fixes: ff7e97c94d ("[media] v4l: vsp1: Store pipeline pointer in rwpf")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e44c153b30 upstream.
The code is checking for negative returns but it should be checking for
zero.
Fixes: aab3125c43 ('[media] em28xx: add support for registering multiple i2c buses')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fa1ce54ea3 upstream.
drivers/nfc/fdp/fdp.c: In function ‘fdp_nci_patch_otp’:
drivers/nfc/fdp/fdp.c:373: warning: comparison is always false due to limited range of data type
drivers/nfc/fdp/fdp.c: In function ‘fdp_nci_patch_ram’:
drivers/nfc/fdp/fdp.c:444: warning: comparison is always false due to limited range of data type
fdp_nci_create_conn() may return a negative error code, which is
silently ignored by assigning it to a u8.
Change conn_id from u8 to int to fix this.
Fixes: a06347c04c ("NFC: Add Intel Fields Peak NFC solution driver")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 849a962729 upstream.
Currently the state sent in SF configuration is always
FULL_ON.
This commit sets the correct state (e.g. INIT_OFF
when station is not associated).
Fixes: commit f4a3ee493e ("iwlwifi: mvm: Always enable the smart FIFO")
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 34875887f3 upstream.
The index calculated when looping through the indir array passed to
fm10k_write_reta was incorrectly calculated as the first part i needs to
be multiplied by 4.
Fixes: 0cfea7a65738 ("fm10k: fix possible null pointer deref after kcalloc", 2016-04-13)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cdf8b46330 upstream.
AT_VECTOR_SIZE_ARCH should be defined with the maximum number of
NEW_AUX_ENT entries that ARCH_DLINFO can contain, but it wasn't defined
for tile at all even though ARCH_DLINFO will contain one NEW_AUX_ENT for
the VDSO address.
This shouldn't be a problem as AT_VECTOR_SIZE_BASE includes space for
AT_BASE_PLATFORM which tile doesn't use, but lets define it now and add
the comment above ARCH_DLINFO as found in several other architectures to
remind future modifiers of ARCH_DLINFO to keep AT_VECTOR_SIZE_ARCH up to
date.
Fixes: 4a556f4f56 ("tile: implement gettimeofday() via vDSO")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Signed-off-by: Chris Metcalf <cmetcalf@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 52d210d961 upstream.
In ee1d267423 ("pstore: add pstore unregister") I added:
.owner = THIS_MODULE,
in both pstore_fs_type and pstore_file_operations to increase a reference
count when pstore filesystem is mounted and pstore file is opened.
But, it's repetitive. There is no need to increase the opened reference
count. We only need to increase the mounted reference count. When a file
is opened, the filesystem can't be unmounted. Hence the pstore module
can't be unloaded either.
So I drop the opened reference count in this patch.
Fixes: ee1d267423 ("pstore: add pstore unregister")
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 52b9c330c6 upstream.
If ->queue_rq() returns BLK_MQ_RQ_QUEUE_OK, we use continue and skip
over the rest of the loop body. However, dptr is assigned later in the
loop body, and the BLK_MQ_RQ_QUEUE_OK case is exactly the case that we'd
want it for.
NVMe isn't actually using BLK_MQ_F_DEFER_ISSUE yet, nor is any other
in-tree driver, but if the code's going to be there, it might as well
work.
Fixes: 74c450521d ("blk-mq: add a 'list' parameter to ->queue_rq()")
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61dc0a446e upstream.
pm_runtime_get_sync does return a error value that must be checked for
error conditions, else, due to various reasons, the device maynot be
enabled and the system will crash due to lack of clock to the hardware
module.
Before:
12.562784] [00000000] *pgd=fe193835
12.562792] Internal error: : 1406 [#1] SMP ARM
[...]
12.562864] CPU: 1 PID: 241 Comm: modprobe Not tainted 4.7.0-rc4-next-20160624 #2
12.562867] Hardware name: Generic DRA74X (Flattened Device Tree)
12.562872] task: ed51f140 ti: ed44c000 task.ti: ed44c000
12.562886] PC is at omap4_rng_init+0x20/0x84 [omap_rng]
12.562899] LR is at set_current_rng+0xc0/0x154 [rng_core]
[...]
After the proper checks:
[ 94.366705] omap_rng 48090000.rng: _od_fail_runtime_resume: FIXME:
missing hwmod/omap_dev info
[ 94.375767] omap_rng 48090000.rng: Failed to runtime_get device -19
[ 94.382351] omap_rng 48090000.rng: initialization failed.
Fixes: 665d92fa85 ("hwrng: OMAP: convert to use runtime PM")
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ad8d52b897 upstream.
PCMCIA suspend/resume no longer works since the commit mentioned below,
as the callbacks are no longer made. Convert the driver to the new
dev_pm_ops, which restores the suspend/resume functionality. Tested on
the arm arch Assabet platform.
Fixes: aa8e54b559 ("PM / sleep: Go direct_complete if driver has no callbacks")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 06dfe5cc0c upstream.
SA1111 PCMCIA was broken when PCMCIA switched to using dev_pm_ops for
the PCMCIA socket class. PCMCIA used to handle suspend/resume via the
socket hosting device, which happened at normal device suspend/resume
time.
However, the referenced commit changed this: much of the resume now
happens much earlier, in the noirq resume handler of dev_pm_ops.
However, on SA1111, the PCMCIA device is not accessible as the SA1111
has not been resumed at _noirq time. It's slightly worse than that,
because the SA1111 has already been put to sleep at _noirq time, so
suspend doesn't work properly.
Fix this by converting the core SA1111 code to use dev_pm_ops as well,
and performing its own suspend/resume at noirq time.
This fixes these errors in the kernel log:
pcmcia_socket pcmcia_socket0: time out after reset
pcmcia_socket pcmcia_socket1: time out after reset
and the resulting lack of PCMCIA cards after a S2RAM cycle.
Fixes: d7646f7632 ("pcmcia: use dev_pm_ops for class pcmcia_socket_class")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2f321126e upstream.
The current implementation only works if the da9xxx devices are added
before their drivers are registered. Only then it can apply the fixes to
both devices. Otherwise, the driver for the first device gets probed
before the fix for the second device can be applied. This is what
fails when using the IP core switcher or when having the i2c master
driver as a module.
So, we need to disable both da9xxx once we detected one of them. We now
use i2c_transfer with hardcoded i2c_messages and device addresses, so we
don't need the da9xxx client devices to be instantiated. Because the
fixup is used on specific boards only, the addresses are not going to
change.
Fixes: 663fbb5215 ("ARM: shmobile: R-Car Gen2: Add da9063/da9210 regulator quirk")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> (r8a7791/koelsch)
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit da60626e7d upstream.
Clear the current reset status prior to rebooting the platform. This
adds the bit missing from 04fef228fb ("[ARM] pxa: introduce
reset_status and clear_reset_status for driver's usage").
Fixes: 04fef228fb ("[ARM] pxa: introduce reset_status and clear_reset_status for driver's usage")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 198b51e8a6 upstream.
Since we switched to use pxa_timer, we need to provide the OSTIMER0
clock. However, as the clock is initialised early, we need to provide
the clock early as well, so that pxa_timer can find it. Adding the
clock to the clkdev table at core_initcall() time is way too late.
Move the initialisation earlier.
Fixes: ee3a4020f7 ("ARM: 8250/1: sa1100: provide OSTIMER0 clock for pxa_timer")
Acked-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b9700be51b upstream.
In commit 99fc5ba0bf ("ARM: dts: imx6sx: add i.mx6sx sabreauto board
support") it should've been enable-sdio-wakeup (not -wakup). But that is
now considered a legacy name for wakeup-source, so directly use the new
name instead, as done in commit 26cefdd15d for the other occurrence.
Fixes: 26cefdd15d ("ARM: dts: imx: replace legacy wakeup property with 'wakeup-source'")
Signed-off-by: Andreas Färber <afaerber@suse.de>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c488f0071e upstream.
The voltage ranges listed here are wrong. The pma8084 pldo
supports three different overlapping voltage ranges with
differing step sizes and the pma8084 ftsmps supports two. These
ranges can be seen in the "native" spmi regulator driver
(qcom_spmi-regulator.c) at pldo_ranges[] and ftsmps_ranges[]
respectively. Port these ranges over to the RPM SMD regulator
driver so that we list the appropriate set of supported voltages
on these types of regulators.
Fixes: ee01d0c91e ("regulator: qcom-smd: Add support for PMA8084")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 290284776b upstream.
The voltage ranges listed here are wrong. The correct ranges can
be seen in the "native" spmi regulator driver
qcom_spmi-regulator.c at pldo_ranges[], ftsmps_ranges[] and
boost_ranges[] for the pldo, ftsmps, and boost type regulators.
Port these ranges over to the RPM SMD regulator driver so that we
list the appropriate set of supported voltages on pldos.
Doing this allows us to specify a voltage like 3075000 for l24,
whereas before that wasn't a supported voltage.
Fixes: da65e367b6 ("regulator: Regulator driver for the Qualcomm RPM")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 93bfe79b03 upstream.
The mvs1 and mvs2 switches are actually called 5vs1 and 5vs2 on
some datasheets. Let's rename them to match the datasheets and
also match the RPM based regulator driver which calls these by
their 5vs names (see qcom_smd-regulator.c). There aren't any
users of these regulators so far, so there aren't any concerns of
DT ABI breakage here. While we're here making updates to the
switches, also mandate usage of the OCP irq for these switches
too.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: e92a404741 ("regulator: Add QCOM SPMI regulator driver")
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c333dfe8db upstream.
The S4 supply is sometimes called the boost regulator because it
outputs 5V. Typically it's connected to the 5vs1 and 5vs2
switches for use in USB OTG and HDMI applications. Add support
for this regulator which was mistakenly left out from the initial
submission of this driver.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: e92a404741 ("regulator: Add QCOM SPMI regulator driver")
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2588393e6 upstream.
The original commit adding support for continuous voltage mode didn't
handle the regulator ramp delay properly. It treated the delay as a
fixed delay in uS despite the property being defined as uV / uS. Let's
adjust it. Luckily there appear to be no users of this ramp delay for
PWM regulators (as per grepping through device trees in linuxnext).
Note also that the upper bound of usleep_range probably shouldn't be a
full 1 ms longer than the lower bound since I've seen plenty of hardware
with a ramp rate of ~5000 uS / uV and for small jumps the total delays
are in the tens of uS. 1000 is way too much. We'll try to be dynamic
and use 10%.
NOTE: This commit doesn't add support for regulator-enable-ramp-delay.
That could be done in a future patch when someone has a user of that
featre.
Though this patch is shows as "fixing" a bug, there are no actual known
users of continuous mode PWM regulator w/ ramp delay in mainline and so
this likely won't have any effect on anyone unless they are working
out-of-tree with private patches. For anyone in this state, it is
highly encouraged to also pick Boris Brezillon's WIP patches to get
yourself a reliable and glitch-free regulator.
Fixes: 4773be185a ("regulator: pwm-regulator: Add support for continuous-voltage")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dbb50887c8 upstream.
During an audit for sk_filter(), we found that rx_busy_skb handling
in l2cap_sock_recv_cb() and l2cap_sock_recvmsg() looks not quite as
intended.
The assumption from commit e328140fda ("Bluetooth: Use event-driven
approach for handling ERTM receive buffer") is that errors returned
from sock_queue_rcv_skb() are due to receive buffer shortage. However,
nothing should prevent doing a setsockopt() with SO_ATTACH_FILTER on
the socket, that could drop some of the incoming skbs when handled in
sock_queue_rcv_skb().
In that case sock_queue_rcv_skb() will return with -EPERM, propagated
from sk_filter() and if in L2CAP_MODE_ERTM mode, wrong assumption was
that we failed due to receive buffer being full. From that point onwards,
due to the to-be-dropped skb being held in rx_busy_skb, we cannot make
any forward progress as rx_busy_skb is never cleared from l2cap_sock_recvmsg(),
due to the filter drop verdict over and over coming from sk_filter().
Meanwhile, in l2cap_sock_recv_cb() all new incoming skbs are being
dropped due to rx_busy_skb being occupied.
Instead, just use __sock_queue_rcv_skb() where an error really tells that
there's a receive buffer issue. Split the sk_filter() and enable it for
non-segmented modes at queuing time since at this point in time the skb has
already been through the ERTM state machine and it has been acked, so dropping
is not allowed. Instead, for ERTM and streaming mode, call sk_filter() in
l2cap_data_rcv() so the packet can be dropped before the state machine sees it.
Fixes: e328140fda ("Bluetooth: Use event-driven approach for handling ERTM receive buffer")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ae6c33ba6e upstream.
Commit bbeddf52ad ("printk: move braille console support into separate
braille.[ch] files") moved the parsing of braille-related options into
_braille_console_setup(), changing the type of variable str from char*
to char**. In this commit, memcmp(str, "brl,", 4) was correctly updated
to memcmp(*str, "brl,", 4) but not memcmp(str, "brl=", 4).
Update the code to make "brl=" option work again and replace memcmp()
with strncmp() to make the compiler able to detect such an issue.
Fixes: bbeddf52ad ("printk: move braille console support into separate braille.[ch] files")
Link: http://lkml.kernel.org/r/20160823165700.28952-1-nicolas.iooss_linux@m4x.org
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 305723ab43 upstream.
Malta boards used with CPU emulators feature a switch to disable use of
an IOCU. Software has to check this switch & ignore any present IOCU if
the switch is closed. The read used to do this was unsafe for 64 bit
kernels, as it simply casted the address 0xbf403000 to a pointer &
dereferenced it. Whilst in a 32 bit kernel this would access kseg1, in a
64 bit kernel this attempts to access xuseg & results in an address
error exception.
Fix by accessing a correctly formed ckseg1 address generated using the
CKSEG1ADDR macro.
Whilst modifying this code, define the name of the register and the bit
we care about within it, which indicates whether PCI DMA is routed to
the IOCU or straight to DRAM. The code previously checked that bit 0 was
also set, but the least significant 7 bits of the CONFIG_GEN0 register
contain the value of the MReqInfo signal provided to the IOCU OCP bus,
so singling out bit 0 makes little sense & that part of the check is
dropped.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: b6d92b4a6b ("MIPS: Add option to disable software I/O coherency.")
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14187/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ddabfa5c2e upstream.
Generic kernel code implements a weak version of set_orig_insn that
moves cached 'insn' from arch_uprobe to the original code location when
the trap is removed.
MIPS variant used arch_uprobe->orig_inst which was never initialised
properly, so this code only inserted a nop instead of the original
instruction. With that change orig_inst can also be safely removed.
Signed-off-by: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Fixes: 40e084a506 ('MIPS: Add uprobes support.')
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14299/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a402a7095 upstream.
When TIF_SINGLESTEP is set for a task, the single-step state machine is
enabled and we must take care not to reset it to the active-not-pending
state if it is already in the active-pending state.
Unfortunately, that's exactly what user_enable_single_step does, by
unconditionally setting the SS bit in the SPSR for the current task.
This causes failures in the GDB testsuite, where GDB ends up missing
expected step traps if the instruction being stepped generates another
trap, e.g. PTRACE_EVENT_FORK from an SVC instruction.
This patch fixes the problem by preserving the current state of the
stepping state machine when TIF_SINGLESTEP is set on the current thread.
Cc: <stable@vger.kernel.org>
Reported-by: Yao Qi <yao.qi@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 117e5e9c4c upstream.
If the bootloader uses the long descriptor format and jumps to
kernel decompressor code, TTBCR may not be in a right state.
Before enabling the MMU, it is required to clear the TTBCR.PD0
field to use TTBR0 for translation table walks.
The commit dbece45894 ("ARM: 7501/1: decompressor:
reset ttbcr for VMSA ARMv7 cores") does the reset of TTBCR.N, but
doesn't consider all the bits for the size of TTBCR.N.
Clear TTBCR.PD0 field and reset all the three bits of TTBCR.N to
indicate the use of TTBR0 and the correct base address width.
Fixes: dbece45894 ("ARM: 7501/1: decompressor: reset ttbcr for VMSA ARMv7 cores")
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Srinivas Ramana <sramana@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 727653d6ce upstream.
gic_raise_softirq() walks the list of cpus using for_each_cpu(), it calls
gic_compute_target_list() which advances the iterator by the number of
CPUs in the cluster.
If gic_compute_target_list() reaches the last CPU it leaves the iterator
pointing at the last CPU. This means the next time round the for_each_cpu()
loop cpumask_next() will be called with an invalid CPU.
This triggers a warning when built with CONFIG_DEBUG_PER_CPU_MAPS:
[ 3.077738] GICv3: CPU1: found redistributor 1 region 0:0x000000002f120000
[ 3.077943] CPU1: Booted secondary processor [410fd0f0]
[ 3.078542] ------------[ cut here ]------------
[ 3.078746] WARNING: CPU: 1 PID: 0 at ../include/linux/cpumask.h:121 gic_raise_softirq+0x12c/0x170
[ 3.078812] Modules linked in:
[ 3.078869]
[ 3.078930] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.8.0-rc5+ #5188
[ 3.078994] Hardware name: Foundation-v8A (DT)
[ 3.079059] task: ffff80087a1a0080 task.stack: ffff80087a19c000
[ 3.079145] PC is at gic_raise_softirq+0x12c/0x170
[ 3.079226] LR is at gic_raise_softirq+0xa4/0x170
[ 3.079296] pc : [<ffff0000083ead24>] lr : [<ffff0000083eac9c>] pstate: 200001c9
[ 3.081139] Call trace:
[ 3.081202] Exception stack(0xffff80087a19fbe0 to 0xffff80087a19fd10)
[ 3.082269] [<ffff0000083ead24>] gic_raise_softirq+0x12c/0x170
[ 3.082354] [<ffff00000808e614>] smp_send_reschedule+0x34/0x40
[ 3.082433] [<ffff0000080e80a0>] resched_curr+0x50/0x88
[ 3.082512] [<ffff0000080e89d0>] check_preempt_curr+0x60/0xd0
[ 3.082593] [<ffff0000080e8a60>] ttwu_do_wakeup+0x20/0xe8
[ 3.082672] [<ffff0000080e8bb8>] ttwu_do_activate+0x90/0xc0
[ 3.082753] [<ffff0000080ea9a4>] try_to_wake_up+0x224/0x370
[ 3.082836] [<ffff0000080eabc8>] default_wake_function+0x10/0x18
[ 3.082920] [<ffff000008103134>] __wake_up_common+0x5c/0xa0
[ 3.083003] [<ffff0000081031f4>] __wake_up_locked+0x14/0x20
[ 3.083086] [<ffff000008103f80>] complete+0x40/0x60
[ 3.083168] [<ffff00000808df7c>] secondary_start_kernel+0x15c/0x1d0
[ 3.083240] [<00000000808911a4>] 0x808911a4
[ 3.113401] Detected PIPT I-cache on CPU2
Avoid updating the iterator if the next call to cpumask_next() would
cause the for_each_cpu() loop to exit.
There is no change to gic_raise_softirq()'s behaviour, (cpumask_next()s
eventual call to _find_next_bit() will return early as start >= nbits),
this patch just silences the warning.
Fixes: 021f653791 ("irqchip: gic-v3: Initial support for GICv3")
Signed-off-by: James Morse <james.morse@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1474306155-3303-1-git-send-email-james.morse@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1e5d343b8f upstream.
The skb_reserve() call only reserved headroom for the mac header, but
not the elp packet header itself.
Fixing this by using skb_put()'ing towards the skb tail instead of
skb_push()'ing towards the skb head.
Fixes: d6f94d91f7 ("batman-adv: ELP - adding basic infrastructure")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 936523441b upstream.
batadv_find_router dereferences last_bonding_candidate from
orig_node without making sure that it has a valid reference. This reference
has to be retrieved by increasing the reference counter while holding
neigh_list_lock. The lock is required to avoid that
batadv_last_bonding_replace removes the current last_bonding_candidate,
reduces the reference counter and maybe destroys the object in this
process.
Fixes: f3b3d90189 ("batman-adv: add bonding again")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b71121b4b7 upstream.
Device notifications are not received after the first interface is
closed; since there is an unregister for notifications on every
interface close. Correct this by unregistering for device
notifications only when the last interface is closed. Also, make
all operations on the i40iw_notifiers_registered atomic as it
can be read/modified concurrently.
Fixes: 8e06af711b ("i40iw: add main, hdr, status")
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 866e0f4d73 upstream.
Update iwqp->hw_iwarp_state to reflect the new state of the CQP
modify QP operation. This avoids reissuing a CQP operation to
modify a QP to a state that it is already in.
Fixes: 4e9042e647 ("i40iw: add hw and utils files")
Reported-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07c72d7d54 upstream.
Send a zero length last streaming mode message for loopback
connections to synchronize between accepting QP and connecting QP.
This avoids data transfer to start on the accepting QP before
the connecting QP is in RTS. Also remove function i40iw_loopback_nop()
as it is no longer used.
Fixes: f27b4746f3 ("i40iw: add connection management code")
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5dfd5e5e3b upstream.
Add NULL check for pdata and pdata->addr before the memcpy in
i40iw_form_cm_frame(). This fixes a NULL pointer de-reference
which occurs when the MPA private data pointer is NULL. Also
only copy pdata->size bytes in the memcpy to prevent reading
past the length of the private data buffer provided by upper layer.
Fixes: f27b4746f3 ("i40iw: add connection management code")
Reported-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 433c58139f upstream.
iwpbl->iwmr points to the structure that contains iwpbl,
which is iwmr. Setting this to NULL would result in
writing to freed memory. So just free iwmr, and return.
Fixes: d374984179 ("i40iw: add files for iwarp interface")
Reported-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d41d0910d9 upstream.
Memory allocated for iwqp; iwqp->allocated_buffer is freed twice in
the create_qp error path. Correct this by having it freed only once in
i40iw_free_qp_resources().
Fixes: d374984179 ("i40iw: add files for iwarp interface")
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c7d46fdb8 upstream.
iwdev->mem_resources is incorrectly defined as an unsigned
long instead of u8. As a result, the offset into the dynamic
allocated structures in i40iw_initialize_hw_resources() is
incorrectly calculated and would lead to writing of memory
regions outside of the allocated buffer.
Fixes: 8e06af711b ("i40iw: add main, hdr, status")
Reported-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0b97a484e5 upstream.
The A-MSDU TX code (within TXQs) didn't always check the return value
of skb_linearize() properly, resulting in potentially passing a frag-
list SKB down to the driver even when it said it can't handle it. Fix
that.
Fixes: 6e0456b545 ("mac80211: add A-MSDU tx support")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 56beac95cb upstream.
ucb1x00 has used IRQ probing since it's dawn to find the GPIO interrupt
that it's connected to. However, commit 23393d49fb ("gpio: kill off
set_irq_flags usage") broke this by disabling IRQ probing on GPIO
interrupts. Fix this.
Fixes: 23393d49fb ("gpio: kill off set_irq_flags usage")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5a7d87da8d upstream.
gcc is apparently unablel to track the state of the local 'resp_v2'
variable across the kzalloc() function, and warns about the response
variable being used without an initialization:
drivers/net/wireless/intel/iwlwifi/mvm/nvm.c: In function ‘iwl_mvm_update_mcc’:
drivers/net/wireless/intel/iwlwifi/mvm/nvm.c:727:36: warning: ‘mcc_resp_v1’ may be used uninitialized in this function [-Wmaybe-uninitialized]
resp_cp->n_channels = mcc_resp_v1->n_channels;
drivers/net/wireless/intel/iwlwifi/mvm/nvm.c:721:3: warning: ‘mcc_resp’ may be used uninitialized in this function [-Wmaybe-uninitialized]
memcpy(resp_cp, mcc_resp, resp_len);
The warning showed up in x86 allmodconfig after my patch to
unhide -Wmaybe-uninitialized warnings by default was merged,
though it always existed in randconfig builds. I did not
catch the warning earlier because I was testing on ARM, which
never produced the warning.
This rearranges the code in a way that improves readability for
both humans and the compiler, and that avoids the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 6fa52430f0 ("iwlwifi: mvm: change mcc update API")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 60dec5233c upstream.
Restart flow zeroes the rx_ba_sessions counter. Mac80211 asks
driver to tear down of the session only afterwards, and as a
result driver didn't free the data. Fix it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Fixes: 10b2b2019d ("iwlwifi: mvm: add infrastructure for tracking BA session in driver")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d5d0689aef upstream.
This fixes a pretty ancient bug that hasn't manifested itself
until now.
The scratchbuf for command queue is allocated only for 32 slots
but is accessed with the queue write pointer - which can be
up to 256.
Since the scratch buf size was 16 and there are up to 256 TFDs
we never passed a page boundary when accessing the scratch buffer,
but when attempting to increase the size of the scratch buffer a
panic was quick to follow when trying to access the address resulted
in a page boundary.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Fixes: 38c0f334b3 ("iwlwifi: use coherent DMA memory for command header")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7c9bd1cc6 upstream.
The TX fifos are arranged consecutively in the SMEM, beginning
with the regular fifos, and tailed by the internal fifos.
In the current code, while trying to read the internal fifos,
we read the fifos beginning with the index zero.
By doing this we actually re-read the regular fifos.
In order to read the internal fifos, start the reading index
from the number of regular fifos configured by the fw.
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Fixes: 39654cb3a6 ("iwlwifi: don't access a nonexistent register upon assert")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c4a247e42 upstream.
Fix an issue where nullfunc frames and block ack requests
had the same tid as aggregation frames and were queued on
a non aggregation queue. The pending frames counter included
those frames but the check whether to decrement the pending
frames counter relied on the tid status and not on the txq id.
The result was an inconsistent state of the pending frames
counter followed by a failure to remove the station.
This failure triggered SYSASSERT 0x3421.
In addition, fix a situation in DQA mode where the number
of pending frames turned negative. This was due to the TX queue
being on the IWL_EMPTYING_HW_QUEUE_DELBA state and its frames
were still decremented.
Even though the SYSASSERT issue is fixed when DQA is disabled,
the issue is not completely solved when DQA is enabled and
should still be fixed.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Fixes: cf961e1662 ("iwlwifi: mvm: support dqa-mode agg on non-shared queue")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ecf5142415 upstream.
Our HW does not support checksum of fragmented packets.
Fix code accordingly to checksum those packets in the driver.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Fixes: 5e6a98dc48 ("iwlwifi: mvm: enable TCP/UDP checksum support for 9000 family")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c3ccf357c3 upstream.
The conversion from a look-up table to a calculation for clock generator
parameters forgot to take into account that BRDV x 1/1 is valid only if
BRPS is x 1/1 or x 1/2, leading to undefined behavior (e.g. arbitrary
clock rates).
This limitation is documented for the MSIOF module in all supported
SH/R-Mobile and R-Car Gen2/Gen3 ARM SoCs.
Tested on r8a7791/koelsch and r8a7795/salvator-x.
Fixes: 65d5665bb2 ("spi: sh-msiof: Update calculation of frequency dividing")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b53893aae4 upstream.
According to the datasheet you should only write 1 to this bit. If it is
not set, at least AIN3 will return bad values on newer silicon revisions.
Fixes: d84ca5b345 ("hwmon: Add driver for ADT7411 voltage and temperature sensor")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a6c5091250 upstream.
nvmem_cell_read() is declared as void * if CONFIG_NVMEM is enabled, and
as char * otherwise. This can result in a build warning if CONFIG_NVMEM
is not enabled and a caller asigns the result to a type other than char *
without using a typecast. Use a consistent declaration to avoid the
problem.
Fixes: e2a5402ec7 ("nvmem: Add nvmem_device based consumer apis.")
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f6aa3264a upstream.
To support UHS modes for Tegra an external regulator must be present
to adjust the IO voltage accordingly. Even if the regulator is not
present but the host supports the UHS modes and the device supports the
UHS modes, then we will attempt to switch to a high-speed mode. Without
an external regulator, Tegra will fail to switch to the high-speed
mode.
It has been found that with some SD cards, that once it has been switch
to operate at a high-speed mode, all subsequent commands issues to the
card will fail and so it will not be possible to switch back to a non
high-speed mode and so the SD card initialisation will fail.
The SDHCI core does not require that the host have an external regulator
when switching to UHS modes and therefore, the Tegra SDHCI host
controller should only advertise the UHS modes as being supported if the
regulator for the IO voltage is present. Fortunately, Tegra has a vendor
specific register which can be used to control which modes are
advertised via the SDHCI_CAPABILITIES register. Hence, if there is no IO
voltage regulator available for the Tegra SDHCI host, then don't
advertise the UHS modes.
Note that if the regulator is not available, we also don't advertise that
the SDHCI is compatible with v3.0 of the SDHCI specification because
this will read the SDHCI_CAPABILITIES_1 register which will enable other
UHS modes.
This fixes commit 7ad2ed1dfc ("mmc: tegra: enable UHS-I modes") which
enables UHS mode without checking if the board can support them.
Fixes: 7ad2ed1dfc ("mmc: tegra: enable UHS-I modes")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b6a3fe8fa upstream.
When tearing down an AUX buf for an event via perf_mmap_close(),
__perf_event_output_stop() is called on the event's CPU to ensure that
trace generation is halted before the process of unmapping and
freeing the buffer pages begins.
The callback is performed via cpu_function_call(), which ensures that it
runs with interrupts disabled and is therefore not preemptible.
Unfortunately, the current code grabs the per-cpu context pointer using
get_cpu_ptr(), which unnecessarily disables preemption and doesn't pair
the call with put_cpu_ptr(), leading to a preempt_count() imbalance and
a BUG when freeing the AUX buffer later on:
WARNING: CPU: 1 PID: 2249 at kernel/events/ring_buffer.c:539 __rb_free_aux+0x10c/0x120
Modules linked in:
[...]
Call Trace:
[<ffffffff813379dd>] dump_stack+0x4f/0x72
[<ffffffff81059ff6>] __warn+0xc6/0xe0
[<ffffffff8105a0c8>] warn_slowpath_null+0x18/0x20
[<ffffffff8112761c>] __rb_free_aux+0x10c/0x120
[<ffffffff81128163>] rb_free_aux+0x13/0x20
[<ffffffff8112515e>] perf_mmap_close+0x29e/0x2f0
[<ffffffff8111da30>] ? perf_iterate_ctx+0xe0/0xe0
[<ffffffff8115f685>] remove_vma+0x25/0x60
[<ffffffff81161796>] exit_mmap+0x106/0x140
[<ffffffff8105725c>] mmput+0x1c/0xd0
[<ffffffff8105cac3>] do_exit+0x253/0xbf0
[<ffffffff8105e32e>] do_group_exit+0x3e/0xb0
[<ffffffff81068d49>] get_signal+0x249/0x640
[<ffffffff8101c273>] do_signal+0x23/0x640
[<ffffffff81905f42>] ? _raw_write_unlock_irq+0x12/0x30
[<ffffffff81905f69>] ? _raw_spin_unlock_irq+0x9/0x10
[<ffffffff81901896>] ? __schedule+0x2c6/0x710
[<ffffffff810022a4>] exit_to_usermode_loop+0x74/0x90
[<ffffffff81002a56>] prepare_exit_to_usermode+0x26/0x30
[<ffffffff81906d1b>] retint_user+0x8/0x10
This patch uses this_cpu_ptr() instead of get_cpu_ptr(), since preemption is
already disabled by the caller.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Reviewed-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Fixes: 95ff4ca26c ("perf/core: Free AUX pages in unmap path")
Link: http://lkml.kernel.org/r/20160824091905.GA16944@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 753246840d upstream.
In case of a IRQ type mismatch in of_pmu_irq_cfg() the
device node for interrupt affinity isn't freed. So fix this
issue by calling of_node_put().
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: fa8ad7889d ("arm: perf: factor arm_pmu core out to drivers")
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit af06d4f74a upstream.
0day found a boot warning triggered in rcu_perf_writer() on !SMP kernel:
WARN_ON(rcu_gp_is_normal() && gp_exp);
, the root cause of which is trying to measure expedited grace
periods(by setting gp_exp to true by default) when all the grace periods
are normal(TINY RCU only has normal grace periods).
However, such a mis-setting would only result in failing to measure the
performance for a specific kind of grace periods, therefore using a
WARN_ON to check this is a little overkilling. We could handle this
inside rcuperf module via some error messages to tell users about the
mis-settings.
Therefore this patch removes the WARN_ON in rcu_perf_writer() and
handles those checkings in rcu_perf_init() with plain if() code.
Moreover, this patch changes the default value of gp_exp to 1) align
with rcutorture tests and 2) make the default setting work for all RCU
implementations by default.
Suggested-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Fixes: http://lkml.kernel.org/r/57411b10.mFvG0+AgcrMXGtcj%fengguang.wu@intel.com
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d248220f04 upstream.
Since commit 6ce0d20016 ("ARM: dma: Use dma_pfn_offset for dma address translation"),
dma_to_pfn() already returns the PFN with the physical memory start offset
so we don't need to add it again.
This fixes USB mass storage lock-up problem on systems that can't do DMA
over the entire physical memory range (e.g.) Keystone 2 systems with 4GB RAM
can only do DMA over the first 2GB. [K2E-EVM].
What happens there is that without this patch SCSI layer sets a wrong
bounce buffer limit in scsi_calculate_bounce_limit() for the USB mass
storage device. dma_max_pfn() evaluates to 0x8fffff and bounce_limit
is set to 0x8fffff000 whereas maximum DMA'ble physical memory on Keystone 2
is 0x87fffffff. This results in non DMA'ble pages being given to the
USB controller and hence the lock-up.
NOTE: in the above case, USB-SCSI-device's dma_pfn_offset was showing as 0.
This should have really been 0x780000 as on K2e, LOWMEM_START is 0x80000000
and HIGHMEM_START is 0x800000000. DMA zone is 2GB so dma_max_pfn should be
0x87ffff. The incorrect dma_pfn_offset for the USB storage device is because
USB devices are not correctly inheriting the dma_pfn_offset from the
USB host controller. This will be fixed by a separate patch.
Fixes: 6ce0d20016 ("ARM: dma: Use dma_pfn_offset for dma address translation")
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ba6dea4f7c upstream.
Whilst MPIDR values themselves are less than 32 bits, it is still
perfectly valid for a DT to have #address-cells > 1 in the CPUs node,
resulting in the "reg" property having leading zero cell(s). In that
situation, the big-endian nature of the data conspires with the current
behaviour of only reading the first cell to cause the kernel to think
all CPUs have ID 0, and become resoundingly unhappy as a consequence.
Take the full property length into account when parsing CPUs so as to
be correct under any circumstances.
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 90fd68dcf9 upstream.
The udl damage handler is supposed to render 'height' lines, but its
iterator has an obvious typo that makes it miss most lines if the
rectangle does not cover 0/0.
Fix the damage handler to correctly render all lines.
This is a fallout from:
commit e375882406
Author: Noralf Trønnes <noralf@tronnes.org>
Date: Thu Apr 28 17:18:37 2016 +0200
drm/udl: Use drm_fb_helper deferred_io support
Tested-by: poma <poma@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Eric Engestrom <eric.engestrom@imgtec.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9abefcb1aa upstream.
A timer was used to restart after the bus-off state, leading to a
relatively large can_restart() executed in an interrupt context,
which in turn sets up pinctrl. When this happens during system boot,
there is a high probability of grabbing the pinctrl_list_mutex,
which is locked already by the probe() of other device, making the
kernel suspect a deadlock condition [1].
To resolve this issue, the restart_timer is replaced by a delayed
work.
[1] https://github.com/victronenergy/venus/issues/24
Signed-off-by: Sergei Miroshnichenko <sergeimir@emcraft.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b398e416e upstream.
I hit the following hung task when runing a OOM LTP test case with 4.1
kernel.
Call trace:
[<ffffffc000086a88>] __switch_to+0x74/0x8c
[<ffffffc000a1bae0>] __schedule+0x23c/0x7bc
[<ffffffc000a1c09c>] schedule+0x3c/0x94
[<ffffffc000a1eb84>] rwsem_down_write_failed+0x214/0x350
[<ffffffc000a1e32c>] down_write+0x64/0x80
[<ffffffc00021f794>] __ksm_exit+0x90/0x19c
[<ffffffc0000be650>] mmput+0x118/0x11c
[<ffffffc0000c3ec4>] do_exit+0x2dc/0xa74
[<ffffffc0000c46f8>] do_group_exit+0x4c/0xe4
[<ffffffc0000d0f34>] get_signal+0x444/0x5e0
[<ffffffc000089fcc>] do_signal+0x1d8/0x450
[<ffffffc00008a35c>] do_notify_resume+0x70/0x78
The oom victim cannot terminate because it needs to take mmap_sem for
write while the lock is held by ksmd for read which loops in the page
allocator
ksm_do_scan
scan_get_next_rmap_item
down_read
get_next_rmap_item
alloc_rmap_item #ksmd will loop permanently.
There is no way forward because the oom victim cannot release any memory
in 4.1 based kernel. Since 4.6 we have the oom reaper which would solve
this problem because it would release the memory asynchronously.
Nevertheless we can relax alloc_rmap_item requirements and use
__GFP_NORETRY because the allocation failure is acceptable as ksm_do_scan
would just retry later after the lock got dropped.
Such a patch would be also easy to backport to older stable kernels which
do not have oom_reaper.
While we are at it add GFP_NOWARN so the admin doesn't have to be alarmed
by the allocation failure.
Link: http://lkml.kernel.org/r/1474165570-44398-1-git-send-email-zhongjiang@huawei.com
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Suggested-by: Hugh Dickins <hughd@google.com>
Suggested-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f6d7c1b559 upstream.
This fixes subpage writes when using 4-bit HW ECC.
There has been numerous reports about ECC errors with devices using this
driver for a while. Also the 4-bit ECC has been reported as broken with
subpages in [1] and with 16 bits NANDs in the driver and in mach* board
files both in mainline and in the vendor BSPs.
What I saw with 4-bit ECC on a 16bits NAND (on an LCDK) which got me to
try reinitializing the ECC engine:
- R/W on whole pages properly generates/checks RS code
- try writing the 1st subpage only of a blank page, the subpage is well
written and the RS code properly generated, re-reading the same page
the HW detects some ECC error, reading the same page again no ECC
error is detected
Note that the ECC engine is already reinitialized in the 1-bit case.
Tested on my LCDK with UBI+UBIFS using subpages.
This could potentially get rid of the issue workarounded in [1].
[1] 28c015a9da ("mtd: davinci-nand: disable subpage write for keystone-nand")
Fixes: 6a4123e581 ("mtd: nand: davinci_nand, 4-bit ECC for smallpage")
Signed-off-by: Karl Beldan <kbeldan@baylibre.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9157056da8 upstream.
On the v2 hierarchy, "cgroup.subtree_control" rejects controller
enables if the cgroup has processes in it. The enforcement of this
logic assumes that the cgroup wouldn't have any css_sets associated
with it if there are no tasks in the cgroup, which is no longer true
since a79a908fd2 ("cgroup: introduce cgroup namespaces").
When a cgroup namespace is created, it pins the css_set of the
creating task to use it as the root css_set of the namespace. This
extra reference stays as long as the namespace is around and makes
"cgroup.subtree_control" think that the namespace root cgroup is not
empty even when it is and thus reject controller enables.
Fix it by making cgroup_subtree_control() walk and test emptiness of
each css_set instead of testing whether the list_head is empty.
While at it, update the comment of cgroup_task_count() to indicate
that the returned value may be higher than the number of tasks, which
has always been true due to temporary references and doesn't break
anything.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Evgeny Vereshchagin <evvers@ya.ru>
Cc: Serge E. Hallyn <serge.hallyn@ubuntu.com>
Cc: Aditya Kali <adityakali@google.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Fixes: a79a908fd2 ("cgroup: introduce cgroup namespaces")
Link: https://github.com/systemd/systemd/pull/3589#issuecomment-249089541
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 28b89b9e6f upstream.
A discrepancy between cpu_online_mask and cpuset's effective_cpus
mask is inevitable during hotplug since cpuset defers updating of
effective_cpus mask using a workqueue, during which time nothing
prevents the system from more hotplug operations. For that reason
guarantee_online_cpus() walks up the cpuset hierarchy until it finds
an intersection under the assumption that top cpuset's effective_cpus
mask intersects with cpu_online_mask even with such a race occurring.
However a sequence of CPU hotplugs can open a time window, during which
none of the effective CPUs in the top cpuset intersect with
cpu_online_mask.
For example when there are 4 possible CPUs 0-3 and only CPU0 is online:
======================== ===========================
cpu_online_mask top_cpuset.effective_cpus
======================== ===========================
echo 1 > cpu2/online.
CPU hotplug notifier woke up hotplug work but not yet scheduled.
[0,2] [0]
echo 0 > cpu0/online.
The workqueue is still runnable.
[2] [0]
======================== ===========================
Now there is no intersection between cpu_online_mask and
top_cpuset.effective_cpus. Thus invoking sys_sched_setaffinity() at
this moment can cause following:
Unable to handle kernel NULL pointer dereference at virtual address 000000d0
------------[ cut here ]------------
Kernel BUG at ffffffc0001389b0 [verbose debug info unavailable]
Internal error: Oops - BUG: 96000005 [#1] PREEMPT SMP
Modules linked in:
CPU: 2 PID: 1420 Comm: taskset Tainted: G W 4.4.8+ #98
task: ffffffc06a5c4880 ti: ffffffc06e124000 task.ti: ffffffc06e124000
PC is at guarantee_online_cpus+0x2c/0x58
LR is at cpuset_cpus_allowed+0x4c/0x6c
<snip>
Process taskset (pid: 1420, stack limit = 0xffffffc06e124020)
Call trace:
[<ffffffc0001389b0>] guarantee_online_cpus+0x2c/0x58
[<ffffffc00013b208>] cpuset_cpus_allowed+0x4c/0x6c
[<ffffffc0000d61f0>] sched_setaffinity+0xc0/0x1ac
[<ffffffc0000d6374>] SyS_sched_setaffinity+0x98/0xac
[<ffffffc000085cb0>] el0_svc_naked+0x24/0x28
The top cpuset's effective_cpus are guaranteed to be identical to
cpu_online_mask eventually. Hence fall back to cpu_online_mask when
there is no intersection between top cpuset's effective_cpus and
cpu_online_mask.
Signed-off-by: Joonwoo Park <joonwoop@codeaurora.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: cgroups@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 15f6d33715 upstream.
On May 4th, Bjørn Mork provided patch 697bbc7b83 ("builddeb: include
objtool binary in headers package"). However, that one only works if
$srctree=$objtree, because the objtool binaries are not written to the
srctree, but to the objtree.
Signed-off-by: Wilfried Klaebe <linux-kernel@lebenslange-mailadresse.de>
Fixes: 697bbc7b83 ("builddeb: include objtool binary in headers package")
Signed-off-by: Michal Marek <mmarek@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 12eb5137ed upstream.
There exists a race where the application can setup a connection
and then disconnect it before iw_cxgb4 processes the fw4_ack
message. For passive side connections, the fw4_ack message is
used to know when to stop the ep timer for MPA_REPLY messages.
If the application disconnects before the fw4_ack is handled then
c4iw_ep_disconnect() needs to clean up the timer state and stop the
timer before restarting it for the disconnect timer. Failure to do this
results in a "timer already started" message and a premature stopping
of the disconnect timer.
Fixes: e4b76a2 ("RDMA/iw_cxgb4: stop_ep_timer() after MPA negotiation")
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4b3ec5a3f4 upstream.
Currently we call quarantine_reduce() for ___GFP_KSWAPD_RECLAIM (implied
by __GFP_RECLAIM) allocation. So, basically we call it on almost every
allocation. quarantine_reduce() sometimes is heavy operation, and
calling it with disabled interrupts may trigger hard LOCKUP:
NMI watchdog: Watchdog detected hard LOCKUP on cpu 2irq event stamp: 1411258
Call Trace:
<NMI> dump_stack+0x68/0x96
watchdog_overflow_callback+0x15b/0x190
__perf_event_overflow+0x1b1/0x540
perf_event_overflow+0x14/0x20
intel_pmu_handle_irq+0x36a/0xad0
perf_event_nmi_handler+0x2c/0x50
nmi_handle+0x128/0x480
default_do_nmi+0xb2/0x210
do_nmi+0x1aa/0x220
end_repeat_nmi+0x1a/0x1e
<<EOE>> __kernel_text_address+0x86/0xb0
print_context_stack+0x7b/0x100
dump_trace+0x12b/0x350
save_stack_trace+0x2b/0x50
set_track+0x83/0x140
free_debug_processing+0x1aa/0x420
__slab_free+0x1d6/0x2e0
___cache_free+0xb6/0xd0
qlist_free_all+0x83/0x100
quarantine_reduce+0x177/0x1b0
kasan_kmalloc+0xf3/0x100
Reduce the quarantine_reduce iff direct reclaim is allowed.
Fixes: 55834c59098d("mm: kasan: initial memory quarantine implementation")
Link: http://lkml.kernel.org/r/1470062715-14077-2-git-send-email-aryabinin@virtuozzo.com
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Acked-by: Alexander Potapenko <glider@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a83f1fc3f3 upstream.
Commit 0259f522e0 ('soc/tegra: pmc: Restore base address on probe
failure') fixes an issue where the PMC base address pointer is not
restored on probe failure. However, this fix creates another problem
where if early initialisation of the PMC driver fails and an initial
mapping for the PMC address space is not created, then when the PMC
device is probed, the PMC base address pointer will not be valid and
this will cause a crash when tegra_pmc_init() is called and attempts
to access a register.
Although the PMC address space is mapped a 2nd time during the probe
and so this could be fixed by populating the base address pointer
earlier during the probe, this adds more complexity to the code.
Moreover, the PMC probe also assumes the the soc data pointer is also
initialised when the device is probed and if not will also lead to a
crash when calling tegra_pmc_init_tsense_reset(). Given that if the
early initialisation does fail then something bad has happen, it seems
acceptable to allow the PMC device probe to fail as well. Therefore, if
the PMC base address pointer or soc data pointer are not valid when
probing the PMC device, WARN and return an error.
Fixes: 0259f522e0 ('soc/tegra: pmc: Restore base address on probe failure')
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0066c8b6f4 upstream.
Fix PHY delay compensation math in igb_ptp_tx_hwtstamp() and
igb_ptp_rx_rgtstamp. Add PHY delay compensation in
igb_ptp_rx_pktstamp().
In the IGB driver, there are two functions that retrieve timestamps
received by the PHY - igb_ptp_rx_rgtstamp() and igb_ptp_rx_pktstamp().
The previous commit only changed igb_ptp_rx_rgtstamp(), and the change
was incorrect.
There are two instances in which PHY delay compensations should be
made:
- Before the packet transmission over the PHY, the latency between
when the packet is timestamped and transmission of the packets,
should be an add operation, but it is currently a subtract.
- After the packets are received from the PHY, the latency between
the receiving and timestamping of the packets should be a subtract
operation, but it is currently an add.
Signed-off-by: Kshitiz Gupta <kshitiz.gupta@ni.com>
Fixes: 3f544d2 (igb: adjust ptp timestamps for tx/rx latency)
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d951822be upstream.
Back when I submitted the GSO code I messed up and dropped the support for
disabling the VLAN tag filtering via the feature bit. This patch
re-enables the use of the NETIF_F_HW_VLAN_CTAG_FILTER to enable/disable the
VLAN filtering independent of toggling promiscuous mode.
Fixes: b83e30104b ("ixgbe/ixgbevf: Add support for GSO partial")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f60439bc21 upstream.
When I was adding the code for enabling VLAN promiscuous mode with SR-IOV
enabled I had inadvertently left the VLNCTRL.VFE bit unchanged as I has
assumed there was code in another path that was setting it when we enabled
SR-IOV. This wasn't the case and as a result we were just disabling VLAN
filtering for all the VFs apparently.
Also the previous patches were always clearing CFIEN which was always set
to 0 by the hardware anyway so I am dropping the redundant bit clearing.
Fixes: 1636956491 ("ixgbe: Add support for VLAN promiscuous with SR-IOV")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5381cfb6f0 upstream.
The device's model download function returns the model data as
an array of u32s, which is later compared to the reference
model data. However, since the latter is an array of u16s,
the comparison does not happen correctly, and model verification
fails. This in turn breaks the POR initialization sequence.
Fixes: 39e7213edc ("max17042_battery: Support regmap to access device's registers")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sven Van Asbroeck <TheSven73@googlemail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 924d869675 upstream.
rtree_next_node() walks the linked list of leaf nodes to find the next
block of pages in the struct memory_bitmap. If it walks off the end of
the list of nodes, it walks the list of memory zones to find the next
region of memory. If it walks off the end of the list of zones, it
returns false.
This leaves the struct bm_position's node and zone pointers pointing
at their respective struct list_heads in struct mem_zone_bm_rtree.
memory_bm_find_bit() uses struct bm_position's node and zone pointers
to avoid walking lists and trees if the next bit appears in the same
node/zone. It handles these values being stale.
Swap rtree_next_node()s 'step then test' to 'test-next then step',
this means if we reach the end of memory we return false and leave
the node and zone pointers as they were.
This fixes a panic on resume using AMD Seattle with 64K pages:
[ 6.868732] Freezing user space processes ... (elapsed 0.000 seconds) done.
[ 6.875753] Double checking all user space processes after OOM killer disable... (elapsed 0.000 seconds)
[ 6.896453] PM: Using 3 thread(s) for decompression.
[ 6.896453] PM: Loading and decompressing image data (5339 pages)...
[ 7.318890] PM: Image loading progress: 0%
[ 7.323395] Unable to handle kernel paging request at virtual address 00800040
[ 7.330611] pgd = ffff000008df0000
[ 7.334003] [00800040] *pgd=00000083fffe0003, *pud=00000083fffe0003, *pmd=00000083fffd0003, *pte=0000000000000000
[ 7.344266] Internal error: Oops: 96000005 [#1] PREEMPT SMP
[ 7.349825] Modules linked in:
[ 7.352871] CPU: 2 PID: 1 Comm: swapper/0 Tainted: G W I 4.8.0-rc1 #4737
[ 7.360512] Hardware name: AMD Overdrive/Supercharger/Default string, BIOS ROD1002C 04/08/2016
[ 7.369109] task: ffff8003c0220000 task.stack: ffff8003c0280000
[ 7.375020] PC is at set_bit+0x18/0x30
[ 7.378758] LR is at memory_bm_set_bit+0x24/0x30
[ 7.383362] pc : [<ffff00000835bbc8>] lr : [<ffff0000080faf18>] pstate: 60000045
[ 7.390743] sp : ffff8003c0283b00
[ 7.473551]
[ 7.475031] Process swapper/0 (pid: 1, stack limit = 0xffff8003c0280020)
[ 7.481718] Stack: (0xffff8003c0283b00 to 0xffff8003c0284000)
[ 7.800075] Call trace:
[ 7.887097] [<ffff00000835bbc8>] set_bit+0x18/0x30
[ 7.891876] [<ffff0000080fb038>] duplicate_memory_bitmap.constprop.38+0x54/0x70
[ 7.899172] [<ffff0000080fcc40>] snapshot_write_next+0x22c/0x47c
[ 7.905166] [<ffff0000080fe1b4>] load_image_lzo+0x754/0xa88
[ 7.910725] [<ffff0000080ff0a8>] swsusp_read+0x144/0x230
[ 7.916025] [<ffff0000080fa338>] load_image_and_restore+0x58/0x90
[ 7.922105] [<ffff0000080fa660>] software_resume+0x2f0/0x338
[ 7.927752] [<ffff000008083350>] do_one_initcall+0x38/0x11c
[ 7.933314] [<ffff000008b40cc0>] kernel_init_freeable+0x14c/0x1ec
[ 7.939395] [<ffff0000087ce564>] kernel_init+0x10/0xfc
[ 7.944520] [<ffff000008082e90>] ret_from_fork+0x10/0x40
[ 7.949820] Code: d2800022 8b400c21 f9800031 9ac32043 (c85f7c22)
[ 7.955909] ---[ end trace 0024a5986e6ff323 ]---
[ 7.960529] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
Here struct mem_zone_bm_rtree's start_pfn has been returned instead of
struct rtree_node's addr as the node/zone pointers are corrupt after
we walked off the end of the lists during mark_unsafe_pages().
This behaviour was exposed by commit 6dbecfd345 ("PM / hibernate:
Simplify mark_unsafe_pages()"), which caused mark_unsafe_pages() to call
duplicate_memory_bitmap(), which uses memory_bm_find_bit() after walking
off the end of the memory bitmap.
Fixes: 3a20cb1779 (PM / Hibernate: Implement position keeping in radix tree)
Signed-off-by: James Morse <james.morse@arm.com>
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 62822e2ec4 upstream.
Restore the processor state before calling any other functions to
ensure per-CPU variables can be used with KASLR memory randomization.
Tracing functions use per-CPU variables (GS based on x86) and one was
called just before restoring the processor state fully. It resulted
in a double fault when both the tracing & the exception handler
functions tried to use a per-CPU variable.
Fixes: bb3632c610 (PM / sleep: trace events for suspend/resume)
Reported-and-tested-by: Borislav Petkov <bp@suse.de>
Reported-by: Jiri Kosina <jikos@kernel.org>
Tested-by: Rafael J. Wysocki <rafael@kernel.org>
Tested-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Thomas Garnier <thgarnie@google.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c22e853a2e upstream.
In case of error, the function ceph_alloc_page_vector() returns
ERR_PTR() and never returns NULL. The NULL test in the return value
check should be replaced with IS_ERR().
Fixes: 1907920324 ('libceph: support for sending notifies')
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 955818cd5b upstream.
ceph_llseek does not correctly return NXIO errors because the 'out' path
always returns 'offset'.
Fixes: 06222e491e ("fs: handle SEEK_HOLE/SEEK_DATA properly in all fs's that define their own llseek")
Signed-off-by: Phil Turnbull <phil.turnbull@oracle.com>
Signed-off-by: Yan, Zheng <zyan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a0f2b65275 upstream.
The genksyms helper in the kernel cannot parse a type definition
like "typeof(((type *)0)->keyfld)" that is used in the DEFINE_RB_FUNCS
helper, causing the following EXPORT_SYMBOL() statement to be ignored
when computing the crcs, and triggering a warning about this:
WARNING: "ceph_monc_do_statfs" [fs/ceph/ceph.ko] has no CRC
To work around the problem, we can rewrite the type to reference
an undefined 'extern' symbol instead of a NULL pointer. This is
evidently ok for genksyms, and it no longer complains about the
line when calling it with 'genksyms -w'.
I've looked briefly into extending genksyms instead, but it seems
really hard to do. Jan Beulich introduced basic support for 'typeof'
a while ago in dc53324060 ("genksyms: fix typeof() handling"),
but that is not sufficient for the expression we have here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: fcd00b68bb ("libceph: DEFINE_RB_FUNCS macro")
Cc: Jan Beulich <jbeulich@suse.com>
Cc: Michal Marek <mmarek@suse.cz>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 281dbe5db8 upstream.
An on-stack oid in ceph_ioctl_get_dataloc() is not initialized,
resulting in a WARN and a NULL pointer dereference later on. We will
have more of these on-stack in the future, so fix it with a convenience
macro.
Fixes: d30291b985 ("libceph: variable-sized ceph_object_id")
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e535ec0899 upstream.
There's a mixture of signed 32-bit and unsigned 32-bit and 64-bit data
types used for keeping track of how many pages have been mapped.
This leads to hangs during boot when mapping large numbers of pages
(multiple terabytes, as reported by Waiman) because those values are
interpreted as being negative.
commit 742563777e ("x86/mm/pat: Avoid truncation when converting
cpa->numpages to address") fixed one of those bugs, but there is
another lurking in __change_page_attr_set_clr().
Additionally, the return value type for the populate_*() functions can
return negative values when a large number of pages have been mapped,
triggering the error paths even though no error occurred.
Consistently use 64-bit types on 64-bit platforms when counting pages.
Even in the signed case this gives us room for regions 8PiB
(pebibytes) in size whilst still allowing the usual negative value
error checking idiom.
Reported-by: Waiman Long <waiman.long@hpe.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
CC: Theodore Ts'o <tytso@mit.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Scott J Norton <scott.norton@hpe.com>
Cc: Douglas Hatch <doug.hatch@hpe.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b244614a60 upstream.
cpu_has_fpu macro uses smp_processor_id() and is currently executed
with preemption enabled, that triggers the warning at runtime.
It is assumed throughout the kernel that if any CPU has an FPU, then all
CPUs would have an FPU as well, so it is safe to perform the check with
preemption enabled - change the code to use raw_ variant of the check to
avoid the warning.
Signed-off-by: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14125/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b03c1e3b8e upstream.
Commit c1a0e9bc88 ("MIPS: Allow compact branch policy to be changed")
added Kconfig entries allowing for the compact branch policy used by the
compiler for MIPSr6 kernels to be specified. This can be useful for
debugging, particularly in systems where compact branches have recently
been introduced.
Unfortunately mainline gcc 5.x supports MIPSr6 but not the
-mcompact-branches compiler flag, leading to MIPSr6 kernels failing to
build with gcc 5.x with errors such as:
mipsel-linux-gnu-gcc: error: unrecognized command line option '-mcompact-branches=optimal'
make[2]: *** [kernel/bounds.s] Error 1
Fixing this by hiding the Kconfig entry behind another seems to be more
hassle than it's worth, as MIPSr6 & compact branches have been around
for a while now and if policy does need to be set for debug it can be
done easily enough with KCFLAGS. Therefore remove the compact branch
policy Kconfig entries & their handling in the Makefile.
This reverts commit c1a0e9bc88 ("MIPS: Allow compact branch policy to
be changed").
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: c1a0e9bc88 ("MIPS: Allow compact branch policy to be changed")
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14241/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 554af0c396 upstream.
The page structures associated with the vDSO pages in the kernel image
are calculated using virt_to_page(), which uses __pa() under the hood to
find the pfn associated with the virtual address. The vDSO data pointers
however point to kernel symbols, so __pa_symbol() should really be used
instead.
Since there is no equivalent to virt_to_page() which uses __pa_symbol(),
fix init_vdso_image() to work directly with pfns, calculated with
__phys_to_pfn(__pa_symbol(...)).
This issue broke the Malta Enhanced Virtual Addressing (EVA)
configuration which has a non-default implementation of __pa_symbol().
This is because it uses a physical alias so that the kernel executes
from KSeg0 (VA 0x80000000 -> PA 0x00000000), while RAM is provided to
the kernel in the KUSeg range (VA 0x00000000 -> PA 0x80000000) which
uses the same underlying RAM.
Since there are no page structures associated with the low physical
address region, some arbitrary kernel memory would be interpreted as a
page structure for the vDSO pages and badness ensues.
Fixes: ebb5e78cc6 ("MIPS: Initial implementation of a VDSO")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14229/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f46cca1e6 upstream.
This patch fixes the possibility of a deadlock when bringing up
secondary CPUs.
The deadlock occurs because the set_cpu_online() is called before
synchronise_count_slave(). This can cause a deadlock if the boot CPU,
having scheduled another thread, attempts to send an IPI to the
secondary CPU, which it sees has been marked online. The secondary is
blocked in synchronise_count_slave() waiting for the boot CPU to enter
synchronise_count_master(), but the boot cpu is blocked in
smp_call_function_many() waiting for the secondary to respond to it's
IPI request.
Fix this by marking the CPU online in cpu_callin_map and synchronising
counters before declaring the CPU online and calculating the maps for
IPIs.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Reported-by: Justin Chen <justinpopo6@gmail.com>
Tested-by: Justin Chen <justinpopo6@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14302/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e956304eb upstream.
In the mipsr2_decoder() function, used to emulate pre-MIPSr6
instructions that were removed in MIPSr6, the init_fpu() function is
called if a removed pre-MIPSr6 floating point instruction is the first
floating point instruction used by the task. However, init_fpu()
performs varous actions that rely upon not being migrated. For example
in the most basic case it sets the coprocessor 0 Status.CU1 bit to
enable the FPU & then loads FP register context into the FPU registers.
If the task were to migrate during this time, it may end up attempting
to load FP register context on a different CPU where it hasn't set the
CU1 bit, leading to errors such as:
do_cpu invoked from kernel context![#2]:
CPU: 2 PID: 7338 Comm: fp-prctl Tainted: G D 4.7.0-00424-g49b0c82 #2
task: 838e4000 ti: 88d38000 task.ti: 88d38000
$ 0 : 00000000 00000001 ffffffff 88d3fef8
$ 4 : 838e4000 88d38004 00000000 00000001
$ 8 : 3400fc01 801f8020 808e9100 24000000
$12 : dbffffff 807b69d8 807b0000 00000000
$16 : 00000000 80786150 00400fc4 809c0398
$20 : 809c0338 0040273c 88d3ff28 808e9d30
$24 : 808e9d30 00400fb4
$28 : 88d38000 88d3fe88 00000000 8011a2ac
Hi : 0040273c
Lo : 88d3ff28
epc : 80114178 _restore_fp+0x10/0xa0
ra : 8011a2ac mipsr2_decoder+0xd5c/0x1660
Status: 1400fc03 KERNEL EXL IE
Cause : 1080002c (ExcCode 0b)
PrId : 0001a920 (MIPS I6400)
Modules linked in:
Process fp-prctl (pid: 7338, threadinfo=88d38000, task=838e4000, tls=766527d0)
Stack : 00000000 00000000 00000000 88d3fe98 00000000 00000000 809c0398 809c0338
808e9100 00000000 88d3ff28 00400fc4 00400fc4 0040273c 7fb69e18 004a0000
004a0000 004a0000 7664add0 8010de18 00000000 00000000 88d3fef8 88d3ff28
808e9100 00000000 766527d0 8010e534 000c0000 85755000 8181d580 00000000
00000000 00000000 004a0000 00000000 766527d0 7fb69e18 004a0000 80105c20
...
Call Trace:
[<80114178>] _restore_fp+0x10/0xa0
[<8011a2ac>] mipsr2_decoder+0xd5c/0x1660
[<8010de18>] do_ri+0x90/0x6b8
[<80105c20>] ret_from_exception+0x0/0x10
Fix this by disabling preemption around the call to init_fpu(), ensuring
that it starts & completes on one CPU.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: b0a668fb20 ("MIPS: kernel: mips-r2-to-r6-emul: Add R2 emulator for MIPS R6")
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14305/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 331dcf421c upstream.
If the i2c device is already runtime suspended, if qup_i2c_suspend is
executed during suspend-to-idle or suspend-to-ram it will result in the
following splat:
WARNING: CPU: 3 PID: 1593 at drivers/clk/clk.c:476 clk_core_unprepare+0x80/0x90
Modules linked in:
CPU: 3 PID: 1593 Comm: bash Tainted: G W 4.8.0-rc3 #14
Hardware name: Qualcomm Technologies, Inc. APQ 8016 SBC (DT)
PC is at clk_core_unprepare+0x80/0x90
LR is at clk_unprepare+0x28/0x40
pc : [<ffff0000086eecf0>] lr : [<ffff0000086f0c58>] pstate: 60000145
Call trace:
clk_core_unprepare+0x80/0x90
qup_i2c_disable_clocks+0x2c/0x68
qup_i2c_suspend+0x10/0x20
platform_pm_suspend+0x24/0x68
...
This patch fixes the issue by executing qup_i2c_pm_suspend_runtime
conditionally in qup_i2c_suspend.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 463e8f845c upstream.
The cached value of the last selected channel prevents retries on the
next call, even on failure to update the selected channel. Fix that.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 371a015344 upstream.
the eg20t driver call request_irq() function before the pch_base_address,
base address of i2c controller's register, is assigned an effective value.
there is one possible scenario that an interrupt which isn't inside eg20t
arrives immediately after request_irq() is executed when i2c controller
shares an interrupt number with others. since the interrupt handler
pch_i2c_handler() has already active as shared action, it will be called
and read its own register to determine if this interrupt is from itself.
At that moment, since base address of i2c registers is not remapped
in kernel space yet,so the INT handler will access an illegal address
and then a error occurs.
Signed-off-by: Yadi.hu <yadi.hu@windriver.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e875bd66df upstream.
Since the device hierarchy domain was added by commit c98c1822ee
("irqchip/mips-gic: Add device hierarchy domain"), GIC local interrupts
have been broken.
Users attempting to setup a per-cpu local IRQ, for example the GIC timer
clock events code in drivers/clocksource/mips-gic-timer.c, the
setup_percpu_irq function would refuse with -EINVAL because the GIC
irqchip driver never called irq_set_percpu_devid so the
IRQ_PER_CPU_DEVID flag was never set for the IRQ. This happens because
irq_set_percpu_devid was being called from the gic_irq_domain_map
function which is no longer called.
Doing only that runs into further problems because gic_dev_domain_alloc
set the struct irq_chip for all interrupts, local or shared, to
gic_level_irq_controller despite that only being suitable for shared
interrupts. The typical outcome of this is that gic_level_irq_controller
callback functions are called for local interrupts, and then hwirq
number calculations overflow & the driver ends up attempting to access
some invalid register with an address calculated from an invalid hwirq
number. Best case scenario is that this then leads to a bus error. This
is fixed by abstracting the setup of the hwirq & chip to a new function
gic_setup_dev_chip which is used by both the root GIC IRQ domain & the
device domain.
Finally, decoding local interrupts failed because gic_dev_domain_alloc
only called irq_domain_alloc_irqs_parent for shared interrupts. Local
ones were therefore never associated with hwirqs in the root GIC IRQ
domain and the virq in gic_handle_local_int would always be 0. This is
fixed by calling irq_domain_alloc_irqs_parent unconditionally & having
gic_irq_domain_alloc handle both local & shared interrupts, which is
easy due to the aforementioned abstraction of chip setup into
gic_setup_dev_chip.
This fixes use of the MIPS GIC timer for clock events, which has been
broken since c98c1822ee ("irqchip/mips-gic: Add device hierarchy
domain") but hadn't been noticed due to a silent fallback to the MIPS
coprocessor 0 count/compare clock events device.
Fixes: c98c1822ee ("irqchip/mips-gic: Add device hierarchy domain")
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Qais Yousef <qsyousef@gmail.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Link: http://lkml.kernel.org/r/20160913165335.31389-1-paul.burton@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 325c50e3ce upstream.
If the subvol/snapshot create/destroy ioctls are passed a regular file
with execute permissions set, we'll eventually Oops while trying to do
inode->i_op->lookup via lookup_one_len.
This patch ensures that the file descriptor refers to a directory.
Fixes: cb8e70901d (Btrfs: Fix subvolume creation locking rules)
Fixes: 76dda93c6a (Btrfs: add snapshot/subvolume destroy ioctl)
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ad5987b47e upstream.
Due to an apparent copy/paste bug, the number of counters for the
beacon configuration were checked twice, instead of checking the
number of probe response counters. Fix this to check the number of
probe response counters before parsing those.
Fixes: 9a774c78e2 ("cfg80211: Support multiple CSA counters")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54c5ef2e93 upstream.
Off-channel action frames (such as ANQP frames) must be sent either on
the AUX queue or on the offchannel queue, otherwise the firmware will
cause a SYSASSERT.
In the current implementation, the queue to be used is correctly set in
the original skb, but this is done after it is copied. Thus the copy
remains with the original, incorrect queue.
Fix this by setting the queue in the original skb before copying it.
Fixes: commit 5c08b0f502 ("iwlwifi: mvm: don't override the rate with the AMSDU len")
Signed-off-by: Beni Lev <beni.lev@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d58790b83 upstream.
Configure the transmitter delay register at +0x1c to correctly handle
the CAN FD bitrate switch (BRS). This moves the SSP (secondary sample
point) to a proper offset, so that the TDC mechanism works and won't
generate error frames on the CAN link.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4de349e786 upstream.
On a imx6ul-pico board the following error is seen during system suspend:
dpm_run_callback(): platform_pm_resume+0x0/0x54 returns -110
PM: Device 2090000.flexcan failed to resume: error -110
The reason for this suspend error is because when the CAN interface is not
active the clocks are disabled and then flexcan_chip_enable() will
always fail due to a timeout error.
In order to fix this issue, only call flexcan_chip_enable/disable()
when the CAN interface is active.
Based on a patch from Dong Aisheng in the NXP kernel.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b385d21f27 upstream.
init_tlb_ubc() looked unnecessary to me: tlb_ubc is statically
initialized with zeroes in the init_task, and copied from parent to
child while it is quiescent in arch_dup_task_struct(); so I went to
delete it.
But inserted temporary debug WARN_ONs in place of init_tlb_ubc() to
check that it was always empty at that point, and found them firing:
because memcg reclaim can recurse into global reclaim (when allocating
biosets for swapout in my case), and arrive back at the init_tlb_ubc()
in shrink_node_memcg().
Resetting tlb_ubc.flush_required at that point is wrong: if the upper
level needs a deferred TLB flush, but the lower level turns out not to,
we miss a TLB flush. But fortunately, that's the only part of the
protocol that does not nest: with the initialization removed, cpumask
collects bits from upper and lower levels, and flushes TLB when needed.
Fixes: 72b252aed5 ("mm: send one IPI per CPU to TLB flush all entries after unmapping pages")
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1245800c0f upstream.
The iter->seq can be reset outside the protection of the mutex. So can
reading of user data. Move the mutex up to the beginning of the function.
Fixes: d7350c3f45 ("tracing/core: make the read callbacks reentrants")
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 85d5313ed7 upstream.
Since mac80211 doesn't currently support TSIDs 8-15 which can
only be used after QoS TSPEC negotiation (and not even after
WMM negotiation), reject attempts to set up aggregation
sessions for them, which might confuse drivers. In mac80211
we do correctly handle that, but the TSIDs should never get
used anyway, and drivers might not be able to handle it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e29385fab0 upstream.
The reset value of weekday is 0x1. This is wrong since
the reset values of the day/month/year make up to Jan 1 2001.
When computed weekday comes out to be Monday. On a scale
of 1-7(Sunday - Saturday) it should be 0x2. So we should not
be relying on the reset value.
Hence compute the wday using the current date/month/year values.
Check if reset wday is any different from the computed wday,
If different then set the wday which we computed using
date/month/year values.
Document Referred:
http://ww1.microchip.com/downloads/en/DeviceDoc/20002266F.pdf
Fixes: 1d1945d261 "drivers/rtc/rtc-ds1307.c: add alarm support for mcp7941x chips"
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 168d7c4e8b upstream.
Prior to commit 6c96f05c8b ("reset: Make [of_]reset_control_get[_foo]
functions wrappers"), the "optional" functions returned -ENOTSUPP when
CONFIG_RESET_CONTROLLER was not set.
Revert back to the old behavior by changing the new
__devm_reset_control_get() and __of_reset_control_get() functions to
return ERR_PTR(-ENOTSUPP) when compiled without CONFIG_RESET_CONTROLLER.
Otherwise they will return -EINVAL causing users to think that an error
occurred when CONFIG_RESET_CONTROLLER is not set.
Fixes: 6c96f05c8b ("reset: Make [of_]reset_control_get[_foo] functions wrappers")
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0658620471 upstream.
In stm_unlock(), the test to determine whether we've fully unlocked the
flash checks for the lock length to be equal to the flash size. That is
a typo/think-o -- the condition actually means the flash is completely
*locked.* We should be using the inverse condition -- that the lock
length is 0 (i.e., no protection).
The result of this bug is that we never actually turn off the Status
Register Write Disable bit, even if the flash is completely unlocked.
Now we can.
Fixes: 47b8edbf0d ("mtd: spi-nor: disallow further writes to SR if WP# is low")
Reported-by: Giorgio <giorgio.nicole@arcor.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 79ad07d457 upstream.
There is a cut and paste issue here. The bug is that we are allocating
more memory than necessary for msp_maps. We should be allocating enough
space for a map_info struct (144 bytes) but we instead allocate enough
for an mtd_info struct (1840 bytes). It's a small waste.
The other part of this is not harmful but when we allocated msp_flash
then we allocated enough space fro a map_info pointer instead of an
mtd_info pointer. But since pointers are the same size it works out
fine.
Anyway, I decided to clean up all three allocations a bit to make them
a bit more consistent and clear.
Fixes: 68aa0fa87f ('[MTD] PMC MSP71xx flash/rootfs mappings')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 38178e7b88 upstream.
commit a894cf6c5a ("mtd: nand: mxc: switch to mtd_ooblayout_ops")
introduced a regression accessing the OOB area from the mxc_nand
driver due to an Obiwan error in the mxc_nand_v[12]_ooblayout_free()
functions. They report a bogus oobregion { 64, 7 } which leads to
errors accessing bogus data when reading the oob area.
Prior to the commit the mtd-oobtest module could be run without any
errors. With the offending commit, this test fails with results like:
|Running mtd-oobtest
|
|=================================================
|mtd_oobtest: MTD device: 5
|mtd_oobtest: MTD device size 524288, eraseblock size 131072, page size 2048, count of eraseblocks 4, pages per eraseblock 64, OOB size 64
|mtd_test: scanning for bad eraseblocks
|mtd_test: scanned 4 eraseblocks, 0 are bad
|mtd_oobtest: test 1 of 5
|mtd_oobtest: writing OOBs of whole device
|mtd_oobtest: written up to eraseblock 0
|mtd_oobtest: written 4 eraseblocks
|mtd_oobtest: verifying all eraseblocks
|mtd_oobtest: error @addr[0x0:0x19] 0x9a -> 0x78 diff 0xe2
|mtd_oobtest: error @addr[0x0:0x1a] 0xcc -> 0x0 diff 0xcc
|mtd_oobtest: error @addr[0x0:0x1b] 0xe0 -> 0x85 diff 0x65
|mtd_oobtest: error @addr[0x0:0x1c] 0x60 -> 0x62 diff 0x2
|mtd_oobtest: error @addr[0x0:0x1d] 0x69 -> 0x45 diff 0x2c
|mtd_oobtest: error @addr[0x0:0x1e] 0xcd -> 0xa0 diff 0x6d
|mtd_oobtest: error @addr[0x0:0x1f] 0xf2 -> 0x60 diff 0x92
|mtd_oobtest: error: verify failed at 0x0
[...]
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Fixes: a894cf6c5a ("mtd: nand: mxc: switch to mtd_ooblayout_ops")
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 42857cf512 upstream.
The check for writing more than cb_max_size bytes does not 'goto out' so
it is a no-op which allows users to vmalloc an arbitrary amount.
Fixes: 03607ace80 ("configfs: implement binary attributes")
Signed-off-by: Phil Turnbull <phil.turnbull@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c18df0adab upstream.
The wq_numa_init() function makes a private CPU to node map by calling
cpu_to_node() early in the boot process, before the non-boot CPUs are
brought online. Since the default implementation of cpu_to_node()
returns zero for CPUs that have never been brought online, the
workqueue system's view is that *all* CPUs are on node zero.
When the unbound workqueue for a non-zero node is created, the
tsk_cpus_allowed() for the worker threads is the empty set because
there are, in the view of the workqueue system, no CPUs on non-zero
nodes. The code in try_to_wake_up() using this empty cpumask ends up
using the cpumask empty set value of NR_CPUS as an index into the
per-CPU area pointer array, and gets garbage as it is one past the end
of the array. This results in:
[ 0.881970] Unable to handle kernel paging request at virtual address fffffb1008b926a4
[ 1.970095] pgd = fffffc00094b0000
[ 1.973530] [fffffb1008b926a4] *pgd=0000000000000000, *pud=0000000000000000, *pmd=0000000000000000
[ 1.982610] Internal error: Oops: 96000004 [#1] SMP
[ 1.987541] Modules linked in:
[ 1.990631] CPU: 48 PID: 295 Comm: cpuhp/48 Tainted: G W 4.8.0-rc6-preempt-vol+ #9
[ 1.999435] Hardware name: Cavium ThunderX CN88XX board (DT)
[ 2.005159] task: fffffe0fe89cc300 task.stack: fffffe0fe8b8c000
[ 2.011158] PC is at try_to_wake_up+0x194/0x34c
[ 2.015737] LR is at try_to_wake_up+0x150/0x34c
[ 2.020318] pc : [<fffffc00080e7468>] lr : [<fffffc00080e7424>] pstate: 600000c5
[ 2.027803] sp : fffffe0fe8b8fb10
[ 2.031149] x29: fffffe0fe8b8fb10 x28: 0000000000000000
[ 2.036522] x27: fffffc0008c63bc8 x26: 0000000000001000
[ 2.041896] x25: fffffc0008c63c80 x24: fffffc0008bfb200
[ 2.047270] x23: 00000000000000c0 x22: 0000000000000004
[ 2.052642] x21: fffffe0fe89d25bc x20: 0000000000001000
[ 2.058014] x19: fffffe0fe89d1d00 x18: 0000000000000000
[ 2.063386] x17: 0000000000000000 x16: 0000000000000000
[ 2.068760] x15: 0000000000000018 x14: 0000000000000000
[ 2.074133] x13: 0000000000000000 x12: 0000000000000000
[ 2.079505] x11: 0000000000000000 x10: 0000000000000000
[ 2.084879] x9 : 0000000000000000 x8 : 0000000000000000
[ 2.090251] x7 : 0000000000000040 x6 : 0000000000000000
[ 2.095621] x5 : ffffffffffffffff x4 : 0000000000000000
[ 2.100991] x3 : 0000000000000000 x2 : 0000000000000000
[ 2.106364] x1 : fffffc0008be4c24 x0 : ffffff0ffffada80
[ 2.111737]
[ 2.113236] Process cpuhp/48 (pid: 295, stack limit = 0xfffffe0fe8b8c020)
[ 2.120102] Stack: (0xfffffe0fe8b8fb10 to 0xfffffe0fe8b90000)
[ 2.125914] fb00: fffffe0fe8b8fb80 fffffc00080e7648
.
.
.
[ 2.442859] Call trace:
[ 2.445327] Exception stack(0xfffffe0fe8b8f940 to 0xfffffe0fe8b8fa70)
[ 2.451843] f940: fffffe0fe89d1d00 0000040000000000 fffffe0fe8b8fb10 fffffc00080e7468
[ 2.459767] f960: fffffe0fe8b8f980 fffffc00080e4958 ffffff0ff91ab200 fffffc00080e4b64
[ 2.467690] f980: fffffe0fe8b8f9d0 fffffc00080e515c fffffe0fe8b8fa80 0000000000000000
[ 2.475614] f9a0: fffffe0fe8b8f9d0 fffffc00080e58e4 fffffe0fe8b8fa80 0000000000000000
[ 2.483540] f9c0: fffffe0fe8d10000 0000000000000040 fffffe0fe8b8fa50 fffffc00080e5ac4
[ 2.491465] f9e0: ffffff0ffffada80 fffffc0008be4c24 0000000000000000 0000000000000000
[ 2.499387] fa00: 0000000000000000 ffffffffffffffff 0000000000000000 0000000000000040
[ 2.507309] fa20: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
[ 2.515233] fa40: 0000000000000000 0000000000000000 0000000000000000 0000000000000018
[ 2.523156] fa60: 0000000000000000 0000000000000000
[ 2.528089] [<fffffc00080e7468>] try_to_wake_up+0x194/0x34c
[ 2.533723] [<fffffc00080e7648>] wake_up_process+0x28/0x34
[ 2.539275] [<fffffc00080d3764>] create_worker+0x110/0x19c
[ 2.544824] [<fffffc00080d69dc>] alloc_unbound_pwq+0x3cc/0x4b0
[ 2.550724] [<fffffc00080d6bcc>] wq_update_unbound_numa+0x10c/0x1e4
[ 2.557066] [<fffffc00080d7d78>] workqueue_online_cpu+0x220/0x28c
[ 2.563234] [<fffffc00080bd288>] cpuhp_invoke_callback+0x6c/0x168
[ 2.569398] [<fffffc00080bdf74>] cpuhp_up_callbacks+0x44/0xe4
[ 2.575210] [<fffffc00080be194>] cpuhp_thread_fun+0x13c/0x148
[ 2.581027] [<fffffc00080dfbac>] smpboot_thread_fn+0x19c/0x1a8
[ 2.586929] [<fffffc00080dbd64>] kthread+0xdc/0xf0
[ 2.591776] [<fffffc0008083380>] ret_from_fork+0x10/0x50
[ 2.597147] Code: b00057e1 91304021 91005021 b8626822 (b8606821)
[ 2.603464] ---[ end trace 58c0cd36b88802bc ]---
[ 2.608138] Kernel panic - not syncing: Fatal exception
Fix by moving call to numa_store_cpu_info() for all CPUs into
smp_prepare_cpus(), which happens before wq_numa_init(). Since
smp_store_cpu_info() now contains only a single function call,
simplify by removing the function and out-lining its contents.
Suggested-by: Robert Richter <rric@kernel.org>
Fixes: 1a2db30034 ("arm64, numa: Add NUMA support for arm64 platforms.")
Signed-off-by: David Daney <david.daney@cavium.com>
Reviewed-by: Robert Richter <rrichter@cavium.com>
Tested-by: Yisheng Xie <xieyisheng1@huawei.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e23d4159b1 upstream.
Switching iov_iter fault-in to multipages variants has exposed an old
bug in underlying fault_in_multipages_...(); they break if the range
passed to them wraps around. Normally access_ok() done by callers will
prevent such (and it's a guaranteed EFAULT - ERR_PTR() values fall into
such a range and they should not point to any valid objects).
However, on architectures where userland and kernel live in different
MMU contexts (e.g. s390) access_ok() is a no-op and on those a range
with a wraparound can reach fault_in_multipages_...().
Since any wraparound means EFAULT there, the fix is trivial - turn
those
while (uaddr <= end)
...
into
if (unlikely(uaddr > end))
return -EFAULT;
do
...
while (uaddr <= end);
Reported-by: Jan Stancek <jstancek@redhat.com>
Tested-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit db2ba40c27 upstream.
During cgroup2 rollout into production, we started encountering css
refcount underflows and css access crashes in the memory controller.
Splitting the heavily shared css reference counter into logical users
narrowed the imbalance down to the cgroup2 socket memory accounting.
The problem turns out to be the per-cpu charge cache. Cgroup1 had a
separate socket counter, but the new cgroup2 socket accounting goes
through the common charge path that uses a shared per-cpu cache for all
memory that is being tracked. Those caches are safe against scheduling
preemption, but not against interrupts - such as the newly added packet
receive path. When cache draining is interrupted by network RX taking
pages out of the cache, the resuming drain operation will put references
of in-use pages, thus causing the imbalance.
Disable IRQs during all per-cpu charge cache operations.
Fixes: f7e1cb6ec5 ("mm: memcontrol: account socket memory in unified hierarchy memory controller")
Link: http://lkml.kernel.org/r/20160914194846.11153-1-hannes@cmpxchg.org
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Vladimir Davydov <vdavydov@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 96d41019e3 upstream.
fanotify_get_response() calls fsnotify_remove_event() when it finds that
group is being released from fanotify_release() (bypass_perm is set).
However the event it removes need not be only in the group's notification
queue but it can have already moved to access_list (userspace read the
event before closing the fanotify instance fd) which is protected by a
different lock. Thus when fsnotify_remove_event() races with
fanotify_release() operating on access_list, the list can get corrupted.
Fix the problem by moving all the logic removing permission events from
the lists to one place - fanotify_release().
Fixes: 5838d4442b ("fanotify: fix double free of pending permission events")
Link: http://lkml.kernel.org/r/1473797711-14111-3-git-send-email-jack@suse.cz
Signed-off-by: Jan Kara <jack@suse.cz>
Reported-by: Miklos Szeredi <mszeredi@redhat.com>
Tested-by: Miklos Szeredi <mszeredi@redhat.com>
Reviewed-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c8de641b1e upstream.
Commit 62c230bc17 ("mm: add support for a filesystem to activate
swap files and use direct_IO for writing swap pages") replaced the
swap_aops dirty hook from __set_page_dirty_no_writeback() with
swap_set_page_dirty().
For normal cases without these special SWP flags code path falls back to
__set_page_dirty_no_writeback() so the behaviour is expected to be the
same as before.
But swap_set_page_dirty() makes use of the page_swap_info() helper to
get the swap_info_struct to check for the flags like SWP_FILE,
SWP_BLKDEV etc as desired for those features. This helper has
BUG_ON(!PageSwapCache(page)) which is racy and safe only for the
set_page_dirty_lock() path.
For the set_page_dirty() path which is often needed for cases to be
called from irq context, kswapd() can toggle the flag behind the back
while the call is getting executed when system is low on memory and
heavy swapping is ongoing.
This ends up with undesired kernel panic.
This patch just moves the check outside the helper to its users
appropriately to fix kernel panic for the described path. Couple of
users of helpers already take care of SwapCache condition so I skipped
them.
Link: http://lkml.kernel.org/r/1473460718-31013-1-git-send-email-santosh.shilimkar@oracle.com
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Joe Perches <joe@perches.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Rik van Riel <riel@redhat.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jens Axboe <axboe@fb.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 800b2694f8 upstream.
xfs_wait_buftarg() waits for all pending I/O, drains the ioend
completion workqueue and walks the LRU until all buffers in the cache
have been released. This is traditionally an unmount operation` but the
mechanism is also reused during filesystem freeze.
xfs_wait_buftarg() invokes drain_workqueue() as part of the quiesce,
which is intended more for a shutdown sequence in that it indicates to
the queue that new operations are not expected once the drain has begun.
New work jobs after this point result in a WARN_ON_ONCE() and are
otherwise dropped.
With filesystem freeze, however, read operations are allowed and can
proceed during or after the workqueue drain. If such a read occurs
during the drain sequence, the workqueue infrastructure complains about
the queued ioend completion work item and drops it on the floor. As a
result, the buffer remains on the LRU and the freeze never completes.
Despite the fact that the overall buffer cache cleanup is not necessary
during freeze, fix up this operation such that it is safe to invoke
during non-unmount quiesce operations. Replace the drain_workqueue()
call with flush_workqueue(), which runs a similar serialization on
pending workqueue jobs without causing new jobs to be dropped. This is
safe for unmount as unmount independently locks out new operations by
the time xfs_wait_buftarg() is invoked.
cc: <stable@vger.kernel.org>
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 377ccbb483 upstream.
With the latest gcc compilers, they give a warning if
__builtin_return_address() parameter is greater than 0. That is because if
it is used by a function called by a top level function (or in the case of
the kernel, by assembly), it can try to access stack frames outside the
stack and crash the system.
The tracing system uses __builtin_return_address() of up to 2! But it is
well aware of the dangers that it may have, and has even added precautions
to protect against it (see the thunk code in arch/x86/entry/thunk*.S)
Linus originally added KBUILD_CFLAGS that would suppress the warning for the
entire kernel, as simply adding KBUILD_CFLAGS to the tracing directory
wouldn't work. The tracing directory plays a bit with the CFLAGS and
requires a little more logic.
This adds that special logic to only suppress the warning for the tracing
directory. If it is used anywhere else outside of tracing, the warning will
still be triggered.
Link: http://lkml.kernel.org/r/20160728223043.51996267@grimm.local.home
Tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 124a3d88fa upstream.
Newer versions of gcc warn about the use of __builtin_return_address()
with a non-zero argument when "-Wall" is specified:
kernel/trace/trace_irqsoff.c: In function ‘stop_critical_timings’:
kernel/trace/trace_irqsoff.c:433:86: warning: calling ‘__builtin_return_address’ with a nonzero argument is unsafe [-Wframe-address]
stop_critical_timing(CALLER_ADDR0, CALLER_ADDR1);
[ .. repeats a few times for other similar cases .. ]
It is true that a non-zero argument is somewhat dangerous, and we do not
actually have very many uses of that in the kernel - but the ftrace code
does use it, and as Stephen Rostedt says:
"We are well aware of the danger of using __builtin_return_address() of
> 0. In fact that's part of the reason for having the "thunk" code in
x86 (See arch/x86/entry/thunk_{64,32}.S). [..] it adds extra frames
when tracking irqs off sections, to prevent __builtin_return_address()
from accessing bad areas. In fact the thunk_32.S states: 'Trampoline to
trace irqs off. (otherwise CALLER_ADDR1 might crash)'."
For now, __builtin_return_address() with a non-zero argument is the best
we can do, and the warning is not helpful and can end up making people
miss other warnings for real problems.
So disable the frame-address warning on compilers that need it.
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e8d666e92 upstream.
Several build configurations had already disabled this warning because
it generates a lot of false positives. But some had not, and it was
still enabled for "allmodconfig" builds, for example.
Looking at the warnings produced, every single one I looked at was a
false positive, and the warnings are frequent enough (and big enough)
that they can easily hide real problems that you don't notice in the
noise generated by -Wmaybe-uninitialized.
The warning is good in theory, but this is a classic case of a warning
that causes more problems than the warning can solve.
If gcc gets better at avoiding false positives, we may be able to
re-enable this warning. But as is, we're better off without it, and I
want to be able to see the *real* warnings.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7cbdb4a286 upstream.
Somewhere along the way the autofs expire operation has changed to hold
a spin lock over expired dentry selection. The autofs indirect mount
expired dentry selection is complicated and quite lengthy so it isn't
appropriate to hold a spin lock over the operation.
Commit 47be61845c ("fs/dcache.c: avoid soft-lockup in dput()") added a
might_sleep() to dput() causing a WARN_ONCE() about this usage to be
issued.
But the spin lock doesn't need to be held over this check, the autofs
dentry info. flags are enough to block walks into dentrys during the
expire.
I've left the direct mount expire as it is (for now) because it is much
simpler and quicker than the indirect mount expire and adding spin lock
release and re-aquires would do nothing more than add overhead.
Fixes: 47be61845c ("fs/dcache.c: avoid soft-lockup in dput()")
Link: http://lkml.kernel.org/r/20160912014017.1773.73060.stgit@pluto.themaw.net
Signed-off-by: Ian Kent <raven@themaw.net>
Reported-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Takashi Iwai <tiwai@suse.de>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: NeilBrown <neilb@suse.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d21c353d5e upstream.
If we punch a hole on a reflink such that following conditions are met:
1. start offset is on a cluster boundary
2. end offset is not on a cluster boundary
3. (end offset is somewhere in another extent) or
(hole range > MAX_CONTIG_BYTES(1MB)),
we dont COW the first cluster starting at the start offset. But in this
case, we were wrongly passing this cluster to
ocfs2_zero_range_for_truncate() to zero out. This will modify the
cluster in place and zero it in the source too.
Fix this by skipping this cluster in such a scenario.
To reproduce:
1. Create a random file of say 10 MB
xfs_io -c 'pwrite -b 4k 0 10M' -f 10MBfile
2. Reflink it
reflink -f 10MBfile reflnktest
3. Punch a hole at starting at cluster boundary with range greater that
1MB. You can also use a range that will put the end offset in another
extent.
fallocate -p -o 0 -l 1048615 reflnktest
4. sync
5. Check the first cluster in the source file. (It will be zeroed out).
dd if=10MBfile iflag=direct bs=<cluster size> count=1 | hexdump -C
Link: http://lkml.kernel.org/r/1470957147-14185-1-git-send-email-ashish.samant@oracle.com
Signed-off-by: Ashish Samant <ashish.samant@oracle.com>
Reported-by: Saar Maoz <saar.maoz@oracle.com>
Reviewed-by: Srinivas Eeda <srinivas.eeda@oracle.com>
Cc: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Joseph Qi <joseph.qi@huawei.com>
Cc: Eric Ren <zren@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e6f0c6e617 upstream.
Commit ac7cf246df ("ocfs2/dlm: fix race between convert and recovery")
checks if lockres master has changed to identify whether new master has
finished recovery or not. This will introduce a race that right after
old master does umount ( means master will change), a new convert
request comes.
In this case, it will reset lockres state to DLM_RECOVERING and then
retry convert, and then fail with lockres->l_action being set to
OCFS2_AST_INVALID, which will cause inconsistent lock level between
ocfs2 and dlm, and then finally BUG.
Since dlm recovery will clear lock->convert_pending in
dlm_move_lockres_to_recovery_list, we can use it to correctly identify
the race case between convert and recovery. So fix it.
Fixes: ac7cf246df ("ocfs2/dlm: fix race between convert and recovery")
Link: http://lkml.kernel.org/r/57CE1569.8010704@huawei.com
Signed-off-by: Joseph Qi <joseph.qi@huawei.com>
Signed-off-by: Jun Piao <piaojun@huawei.com>
Cc: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 53a5d5ddcc upstream.
The current implementation uses a global per-cpu array to store
data which are used to derive the next IV. This is insecure as
the attacker may change the stored data.
This patch removes all traces of chaining and replaces it with
multiplication of the salt and the sequence number.
Fixes: a10f554fa7 ("crypto: echainiv - Add encrypted chain IV...")
Reported-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit acdb04d0b3 upstream.
When we need to allocate a temporary blkcipher_walk_next and it
fails, the code is supposed to take the slow path of processing
the data block by block. However, due to an unrelated change
we instead end up dereferencing the NULL pointer.
This patch fixes it by moving the unrelated bsize setting out
of the way so that we enter the slow path as inteded.
Fixes: 7607bd8ff0 ("[CRYPTO] blkcipher: Added blkcipher_walk_virt_block")
Reported-by: xiakaixu <xiakaixu@huawei.com>
Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f82e90b286 upstream.
The AES-CTR glue code avoids calling into the blkcipher API for the
tail portion of the walk, by comparing the remainder of walk.nbytes
modulo AES_BLOCK_SIZE with the residual nbytes, and jumping straight
into the tail processing block if they are equal. This tail processing
block checks whether nbytes != 0, and does nothing otherwise.
However, in case of an allocation failure in the blkcipher layer, we
may enter this code with walk.nbytes == 0, while nbytes > 0. In this
case, we should not dereference the source and destination pointers,
since they may be NULL. So instead of checking for nbytes != 0, check
for (walk.nbytes % AES_BLOCK_SIZE) != 0, which implies the former in
non-error conditions.
Fixes: 86464859cc ("crypto: arm - AES in ECB/CBC/CTR/XTS modes using ARMv8 Crypto Extensions")
Reported-by: xiakaixu <xiakaixu@huawei.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2db34e78f1 upstream.
The AES-CTR glue code avoids calling into the blkcipher API for the
tail portion of the walk, by comparing the remainder of walk.nbytes
modulo AES_BLOCK_SIZE with the residual nbytes, and jumping straight
into the tail processing block if they are equal. This tail processing
block checks whether nbytes != 0, and does nothing otherwise.
However, in case of an allocation failure in the blkcipher layer, we
may enter this code with walk.nbytes == 0, while nbytes > 0. In this
case, we should not dereference the source and destination pointers,
since they may be NULL. So instead of checking for nbytes != 0, check
for (walk.nbytes % AES_BLOCK_SIZE) != 0, which implies the former in
non-error conditions.
Fixes: 49788fe2a1 ("arm64/crypto: AES-ECB/CBC/CTR/XTS using ARMv8 NEON and Crypto Extensions")
Reported-by: xiakaixu <xiakaixu@huawei.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 194dc870a5 upstream.
Some of our "for_each_xyz()" macro constructs make gcc unhappy about
lack of braces around if-statements inside or outside the loop, because
the loop construct itself has a "if-then-else" statement inside of it.
The resulting warnings look something like this:
drivers/gpu/drm/i915/i915_debugfs.c: In function ‘i915_dump_lrc’:
drivers/gpu/drm/i915/i915_debugfs.c:2103:6: warning: suggest explicit braces to avoid ambiguous ‘else’ [-Wparentheses]
if (ctx != dev_priv->kernel_context)
^
even if the code itself is fine.
Since the warning is fairly easy to avoid by adding a braces around the
if-statement near the for_each_xyz() construct, do so, rather than
disabling the otherwise potentially useful warning.
(The if-then-else statements used in the "for_each_xyz()" constructs are
designed to be inherently safe even with no braces, but in this case
it's quite understandable that gcc isn't really able to tell that).
This finally leaves the standard "allmodconfig" build with just a
handful of remaining warnings, so new and valid warnings hopefully will
stand out.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4364e1a29b upstream.
virq is not required to be the same for all msi descs. Use the base irq number
from the desc in the debug printk.
Reported-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2cce76c3fa upstream.
gcc-6 warns about code in il3945_hw_txq_ctx_free() being
somewhat ambiguous:
drivers/net/wireless/intel/iwlegacy/3945.c:1022:5: warning: suggest explicit braces to avoid ambiguous 'else' [-Wparentheses]
This adds a set of curly braces to avoid the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit acb2505d01 upstream.
... that should zero on faults. Also remove the <censored> helpful
logics wrt range truncation copied from ppc32. Where it had ever
been needed only in case of copy_from_user() *and* had not been merged
into the mainline until a month after the need had disappeared.
A decade before openrisc went into mainline, I might add...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2545e5da08 upstream.
... in all cases, including the failing access_ok()
Note that some architectures using asm-generic/uaccess.h have
__copy_from_user() not zeroing the tail on failure halfway
through. This variant works either way.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eb47e0293b upstream.
* copy_from_user() on access_ok() failure ought to zero the destination
* none of those primitives should skip the access_ok() check in case of
small constant size.
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3b8767a8f0 upstream.
It should check access_ok(). Otherwise a bunch of places turn into
trivially exploitable rootholes.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c685238922 upstream.
It could be done in exception-handling bits in __get_user_b() et.al.,
but the surgery involved would take more knowledge of sh64 details
than I have or _want_ to have.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c109fabbd upstream.
get_user_ex(x, ptr) should zero x on failure. It's not a lot of a leak
(at most we are leaking uninitialized 64bit value off the kernel stack,
and in a fairly constrained situation, at that), but the fix is trivial,
so...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[ This sat in different branch from the uaccess fixes since mid-August ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8630c32275 upstream.
really ugly, but apparently avr32 compilers turns access_ok() into
something so bad that they want it in assembler. Left that way,
zeroing added in inline wrapper.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ae50f4512 upstream.
Some ST platforms contain interconnect (ICN) clocks which must be handed
correctly in order to obtain full functionality of a given IP. In this
case, if the ICN clocks are not handled properly by the ST SDHCI driver
MMC will break and the following output can be observed:
[ 13.916949] mmc0: Timeout waiting for hardware interrupt.
[ 13.922349] sdhci: =========== REGISTER DUMP (mmc0)===========
[ 13.928175] sdhci: Sys addr: 0x00000000 | Version: 0x00001002
[ 13.933999] sdhci: Blk size: 0x00007040 | Blk cnt: 0x00000001
[ 13.939825] sdhci: Argument: 0x00fffff0 | Trn mode: 0x00000013
[ 13.945650] sdhci: Present: 0x1fff0206 | Host ctl: 0x00000011
[ 13.951475] sdhci: Power: 0x0000000f | Blk gap: 0x00000080
[ 13.957300] sdhci: Wake-up: 0x00000000 | Clock: 0x00003f07
[ 13.963126] sdhci: Timeout: 0x00000004 | Int stat: 0x00000000
[ 13.968952] sdhci: Int enab: 0x02ff008b | Sig enab: 0x02ff008b
[ 13.974777] sdhci: AC12 err: 0x00000000 | Slot int: 0x00000000
[ 13.980602] sdhci: Caps: 0x21ed3281 | Caps_1: 0x00000000
[ 13.986428] sdhci: Cmd: 0x0000063a | Max curr: 0x00000000
[ 13.992252] sdhci: Host ctl2: 0x00000000
[ 13.996166] sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0x7c048200
[ 14.001990] sdhci: ===========================================
[ 14.009802] mmc0: Got data interrupt 0x02000000 even though no data operation was in progress.
A decent point was raised about minimising the use of a local variable that
we 'could' do without. I've chosen consistency over the possibility of
reducing the local variable count by 1. Thinking that it's more important
for the code to be grouped and authoured in a similar manner/style for
greater maintainability/readability.
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 47a66e45d7 upstream.
Similar to struct drm_update_draw, struct drm_mode_fb_cmd2 has an
unaligned 64 bit field (modifier). This get packed differently between
32 bit and 64 bit modes on architectures that can handle unaligned 64
bit access (X86 and IA64). Other architectures pack the structs the
same and don't need the compat wrapper. Use the same condition for
drm_mode_fb_cmd2 as we use for drm_update_draw.
Note that only the modifier will be packed differently between compat
and non-compat versions.
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Kristian H. Kristensen <hoegsberg@chromium.org>
[seanpaul added not at bottom of commit msg re: modifier]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1473801645-116011-1-git-send-email-hoegsberg@chromium.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d31ed3f057 upstream.
The code is applying the same scaling for the X and Y components,
thus making the scaling feature only functional when both components
have the same scaling factor.
Do the s/_w/_h/ replacement where appropriate to fix vertical scaling.
Signed-off-by: Jan Leupold <leupold@rsi-elektrotechnik.de>
Fixes: 1a396789f6 ("drm: add Atmel HLCDC Display Controller support")
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 236dec0510 upstream.
Using "make tinyconfig" produces a couple of annoying warnings that show
up for build test machines all the time:
.config:966:warning: override: NOHIGHMEM changes choice state
.config:965:warning: override: SLOB changes choice state
.config:963:warning: override: KERNEL_XZ changes choice state
.config:962:warning: override: CC_OPTIMIZE_FOR_SIZE changes choice state
.config:933:warning: override: SLOB changes choice state
.config:930:warning: override: CC_OPTIMIZE_FOR_SIZE changes choice state
.config:870:warning: override: SLOB changes choice state
.config:868:warning: override: KERNEL_XZ changes choice state
.config:867:warning: override: CC_OPTIMIZE_FOR_SIZE changes choice state
I've made a previous attempt at fixing them and we discussed a number of
alternatives.
I tried changing the Makefile to use "merge_config.sh -n
$(fragment-list)" but couldn't get that to work properly.
This is yet another approach, based on the observation that we do want
to see a warning for conflicting 'choice' options, and that we can
simply make them non-conflicting by listing all other options as
disabled. This is a trivial patch that we can apply independent of
plans for other changes.
Link: http://lkml.kernel.org/r/20160829214952.1334674-2-arnd@arndb.de
Link: https://storage.kernelci.org/mainline/v4.7-rc6/x86-tinyconfig/build.loghttps://patchwork.kernel.org/patch/9212749/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3610a2add3 upstream.
The compilation emits a warning in function ‘snprintf’,
inlined from ‘set_cmdline’ at
../Documentation/mic/mpssd/mpssd.c:1541:9:
/usr/include/x86_64-linux-gnu/bits/stdio2.h:64:10:
warning: call to __builtin___snprintf_chk will always overflow
destination buffer
This was introduced in commit f4a66c2044 ("misc: mic: Update MIC host
daemon with COSM changes") and is fixed by reverting the changes to the
size argument of these snprintf statements.
Cc: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Mike Danese <mikedanese@google.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8540571e01 upstream.
Commit 7aef413656 ("powerpc32: rewrite csum_partial_copy_generic()
based on copy_tofrom_user()") introduced a bug when destination address
is odd and len is lower than cacheline size.
In that case the resulting csum value doesn't have to be rotated one
byte because the cache-aligned copy part is skipped so no alignment
is performed.
Fixes: 7aef413656 ("powerpc32: rewrite csum_partial_copy_generic() based on copy_tofrom_user()")
Cc: stable@vger.kernel.org # v4.6+
Reported-by: Alessio Igor Bogani <alessio.bogani@elettra.eu>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Tested-by: Alessio Igor Bogani <alessio.bogani@elettra.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1bc8b816cb upstream.
Commit 7aef413656 ("powerpc32: rewrite csum_partial_copy_generic()
based on copy_tofrom_user()") introduced a bug when destination
address is odd and initial csum is not null
In that (rare) case the initial csum value has to be rotated one byte
as well as the resulting value is
This patch also fixes related comments
Fixes: 7aef413656 ("powerpc32: rewrite csum_partial_copy_generic() based on copy_tofrom_user()")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d64934019f upstream.
The eboot code directly calls ExitBootServices. This is inadvisable as the
UEFI spec details a complex set of errors, race conditions, and API
interactions that the caller of ExitBootServices must get correct. The
eboot code attempts allocations after calling ExitBootSerives which is
not permitted per the spec. Call the efi_exit_boot_services() helper
intead, which handles the allocation scenario properly.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ed9cc156c4 upstream.
The FDT code directly calls ExitBootServices. This is inadvisable as the
UEFI spec details a complex set of errors, race conditions, and API
interactions that the caller of ExitBootServices must get correct. The
FDT code does not handle EFI_INVALID_PARAMETER as required by the spec,
which causes intermittent boot failures on the Qualcomm Technologies
QDF2432. Call the efi_exit_boot_services() helper intead, which handles
the EFI_INVALID_PARAMETER scenario properly.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc07716ba8 upstream.
The spec allows ExitBootServices to fail with EFI_INVALID_PARAMETER if a
race condition has occurred where the EFI has updated the memory map after
the stub grabbed a reference to the map. The spec defines a retry
proceedure with specific requirements to handle this scenario.
This scenario was previously observed on x86 - commit d3768d885c ("x86,
efi: retry ExitBootServices() on failure") but the current fix is not spec
compliant and the scenario is now observed on the Qualcomm Technologies
QDF2432 via the FDT stub which does not handle the error and thus causes
boot failures. The user will notice the boot failure as the kernel is not
executed and the system may drop back to a UEFI shell, but will be
unresponsive to input and the system will require a power cycle to recover.
Add a helper to the stub library that correctly adheres to the spec in the
case of EFI_INVALID_PARAMETER from ExitBootServices and can be universally
used across all stub implementations.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dadb57abc3 upstream.
efi_get_memory_map() allocates a buffer to store the memory map that it
retrieves. This buffer may need to be reused by the client after
ExitBootServices() is called, at which point allocations are not longer
permitted. To support this usecase, provide the allocated buffer size back
to the client, and allocate some additional headroom to account for any
reasonable growth in the map that is likely to happen between the call to
efi_get_memory_map() and the client reusing the buffer.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ab34380162 upstream.
Commit 8eb30be035 ("ipv6: Create ip6_tnl_xmit") unsets
flowi6_proto in ip4ip6_tnl_xmit() and ip6ip6_tnl_xmit().
Since xfrm_selector_match() relies on this info, IPv6 packets
sent by an ip6tunnel cannot be properly selected by their
protocols after removing it. This patch puts flowi6_proto back.
Fixes: 8eb30be035 ("ipv6: Create ip6_tnl_xmit")
Signed-off-by: Eli Cooper <elicooper@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 135e8c9250 upstream.
The origin of the issue I've seen is related to
a missing memory barrier between check for task->state and
the check for task->on_rq.
The task being woken up is already awake from a schedule()
and is doing the following:
do {
schedule()
set_current_state(TASK_(UN)INTERRUPTIBLE);
} while (!cond);
The waker, actually gets stuck doing the following in
try_to_wake_up():
while (p->on_cpu)
cpu_relax();
Analysis:
The instance I've seen involves the following race:
CPU1 CPU2
while () {
if (cond)
break;
do {
schedule();
set_current_state(TASK_UN..)
} while (!cond);
wakeup_routine()
spin_lock_irqsave(wait_lock)
raw_spin_lock_irqsave(wait_lock) wake_up_process()
} try_to_wake_up()
set_current_state(TASK_RUNNING); ..
list_del(&waiter.list);
CPU2 wakes up CPU1, but before it can get the wait_lock and set
current state to TASK_RUNNING the following occurs:
CPU3
wakeup_routine()
raw_spin_lock_irqsave(wait_lock)
if (!list_empty)
wake_up_process()
try_to_wake_up()
raw_spin_lock_irqsave(p->pi_lock)
..
if (p->on_rq && ttwu_wakeup())
..
while (p->on_cpu)
cpu_relax()
..
CPU3 tries to wake up the task on CPU1 again since it finds
it on the wait_queue, CPU1 is spinning on wait_lock, but immediately
after CPU2, CPU3 got it.
CPU3 checks the state of p on CPU1, it is TASK_UNINTERRUPTIBLE and
the task is spinning on the wait_lock. Interestingly since p->on_rq
is checked under pi_lock, I've noticed that try_to_wake_up() finds
p->on_rq to be 0. This was the most confusing bit of the analysis,
but p->on_rq is changed under runqueue lock, rq_lock, the p->on_rq
check is not reliable without this fix IMHO. The race is visible
(based on the analysis) only when ttwu_queue() does a remote wakeup
via ttwu_queue_remote. In which case the p->on_rq change is not
done uder the pi_lock.
The result is that after a while the entire system locks up on
the raw_spin_irqlock_save(wait_lock) and the holder spins infintely
Reproduction of the issue:
The issue can be reproduced after a long run on my system with 80
threads and having to tweak available memory to very low and running
memory stress-ng mmapfork test. It usually takes a long time to
reproduce. I am trying to work on a test case that can reproduce
the issue faster, but thats work in progress. I am still testing the
changes on my still in a loop and the tests seem OK thus far.
Big thanks to Benjamin and Nick for helping debug this as well.
Ben helped catch the missing barrier, Nick caught every missing
bit in my theory.
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
[ Updated comment to clarify matching barriers. Many
architectures do not have a full barrier in switch_to()
so that cannot be relied upon. ]
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Alexey Kardashevskiy <aik@ozlabs.ru>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nicholas Piggin <nicholas.piggin@gmail.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/e02cce7b-d9ca-1ad0-7a61-ea97c7582b37@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4d0bd46a4d upstream.
This reverts commit 3d5fdff46c.
Ben Hutchings pointed out that the commit isn't safe since it assumes
that the structure used by the driver is iw_point, when in fact there's
no way to know about that.
Fortunately, the only driver in the tree that ever runs this code path
is the wilc1000 staging driver, so it doesn't really matter.
Clearly I should have investigated this better before applying, sorry.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: 3d5fdff46c ("wext: Fix 32 bit iwpriv compatibility issue with 64 bit Kernel")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 080fe0b790 upstream.
While the Intel PMU monitors the LLC when perf enables the
HW_CACHE_REFERENCES and HW_CACHE_MISSES events, these events monitor
L1 instruction cache fetches (0x0080) and instruction cache misses
(0x0081) on the AMD PMU.
This is extremely confusing when monitoring the same workload across
Intel and AMD machines, since parameters like,
$ perf stat -e cache-references,cache-misses
measure completely different things.
Instead, make the AMD PMU measure instruction/data cache and TLB fill
requests to the L2 and instruction/data cache and TLB misses in the L2
when HW_CACHE_REFERENCES and HW_CACHE_MISSES are enabled,
respectively. That way the events measure unified caches on both
platforms.
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1472044328-21302-1-git-send-email-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 79d102cbfd upstream.
Yanqiu Zhang reported kernel panic when using mbm event
on system where CQM is detected but without mbm event
support, like with perf:
# perf stat -e 'intel_cqm/event=3/' -a
BUG: unable to handle kernel NULL pointer dereference at 0000000000000020
IP: [<ffffffff8100d64c>] update_sample+0xbc/0xe0
...
<IRQ>
[<ffffffff8100d688>] __intel_mbm_event_init+0x18/0x20
[<ffffffff81113d6b>] flush_smp_call_function_queue+0x7b/0x160
[<ffffffff81114853>] generic_smp_call_function_single_interrupt+0x13/0x60
[<ffffffff81052017>] smp_call_function_interrupt+0x27/0x40
[<ffffffff816fb06c>] call_function_interrupt+0x8c/0xa0
...
The reason is that we currently allow to init mbm event
even if mbm support is not detected. Adding checks for
both cqm and mbm events and support into cqm's event_init.
Fixes: 33c3cc7acf ("perf/x86/mbm: Add Intel Memory B/W Monitoring enumeration and init")
Reported-by: Yanqiu Zhang <yanqzhan@redhat.com>
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Vikas Shivappa <vikas.shivappa@linux.intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/1473089407-21857-1-git-send-email-jolsa@kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e34f2ff40e upstream.
A regression was introduced in commit id 79d4db1214 ("ath9k: cleanup
led_pin initial") that broken the WLAN status led on my laptop with
AR9287 after suspending and resuming.
Steps to reproduce:
* Suspend (laptop)
* Resume (laptop)
* Observe that the WLAN led no longer turns ON/OFF depending on the
status and is always red
Even though for my case it only needs to be set to OUT in ath9k_start
but for consistency bring back the IN direction setting as well.
Fixes: 79d4db1214 ("ath9k: cleanup led_pin initial")
Cc: Miaoqing Pan <miaoqing@codeaurora.org>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=151711
Signed-off-by: Giedrius Statkevičius <giedrius.statkevicius@gmail.com>
[kvalo@qca.qualcomm.com: improve commit log]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7711aaf08a upstream.
A station pointer can be passed to the driver on tx, before it has been
marked as associated. Since ath9k_sta_state was initializing the entry
too late, it resulted in some spurious crashes.
Fixes: df3c6eb34d ("ath9k: Use sta_state() callback")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 47a7b0d888 upstream.
The md-cluster is compiled as module by default,
if it is compiled by built-in way, then we can't
make md-cluster works.
[64782.630008] md/raid1:md127: active with 2 out of 2 mirrors
[64782.630528] md-cluster module not found.
[64782.630530] md127: Could not setup cluster service (-2)
Fixes: edb39c9 ("Introduce md_cluster_operations to handle cluster functions")
Reported-by: Marc Smith <marc.smith@mcc.edu>
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bcf42aa60c upstream.
The stop endpoint command has its own 5 second timeout timer.
If the timeout function is triggered between USB3 and USB2 host
removal it will try to call usb_hc_died(xhci_to_hcd(xhci)->primary_hcd)
the ->primary_hcd will be set to NULL at USB3 hcd removal.
Fix this by first checking if the PCI host is being removed, and
also by using only xhci_to_hcd() as it will always return the primary
hcd.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8fba54aebb upstream.
When reading from a loop device backed by a fuse file it deadlocks on
lock_page().
This is because the page is already locked by the read() operation done on
the loop device. In this case we don't want to either lock the page or
dirty it.
So do what fs/direct-io.c does: only dirty the page for ITER_IOVEC vectors.
Reported-by: Sheng Yang <sheng@yasker.org>
Fixes: aa4d86163e ("block: loop: switch to VFS ITER_BVEC")
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Reviewed-by: Sheng Yang <sheng@yasker.org>
Reviewed-by: Ashish Samant <ashish.samant@oracle.com>
Tested-by: Sheng Yang <sheng@yasker.org>
Tested-by: Ashish Samant <ashish.samant@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cbd60aa7cd upstream.
We use a btrfs_log_ctx structure to pass information into the
tree log commit, and get error values out. It gets added to a per
log-transaction list which we walk when things go bad.
Commit d1433debe added an optimization to skip waiting for the log
commit, but didn't take root_log_ctx out of the list. This
patch makes sure we remove things before exiting.
Signed-off-by: Chris Mason <clm@fb.com>
Fixes: d1433debe7
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0bd2223594 upstream.
When calling .import() on a cryptd ahash_request, the structure members
that describe the child transform in the shash_desc need to be initialized
like they are when calling .init()
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 872c63fbf9 upstream.
smp_mb__before_spinlock() is intended to upgrade a spin_lock() operation
to a full barrier, such that prior stores are ordered with respect to
loads and stores occuring inside the critical section.
Unfortunately, the core code defines the barrier as smp_wmb(), which
is insufficient to provide the required ordering guarantees when used in
conjunction with our load-acquire-based spinlock implementation.
This patch overrides the arm64 definition of smp_mb__before_spinlock()
to map to a full smp_mb().
Cc: Peter Zijlstra <peterz@infradead.org>
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23540d6e2f upstream.
A recent commit (inadvertently?) changed how failed probe of a gpmc
child node was handled. Instead of proceeding with setting up any other
children as before, a single error now aborts the whole process.
This change broke networking on some Overo boards due to probe failing
for an unrelated nand node. This second issue should obviously be
fixed, but let's restore the old behaviour of allowing child-node
probe to fail to avoid further similar breakage on other systems.
Fixes: d2d00862df ("memory: omap-gpmc: Support general purpose input
for WAITPINs")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 486095fae3 upstream.
PG8, PG9 is said to be the CTS/RTS pins for UART1 according to the A23/33
datasheets. However, the function is wrongly named "uart2" in the pinctrl
driver. This patch fixes this by modifying them to be named "uart1".
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a32ac2912f upstream.
A previous patch attempted to fix the pinmuxes for mfio 84 - 89, but it
omitted a change to pistachio_pin_group pistachio_groups, which results
in incorrect pll_lock signals being routed.
Apply the correct mux settings throughout the driver.
fixes: cefc03e599 ("pinctrl: Add Pistachio SoC pin control driver")
fixes: e9adb336d0 ("pinctrl: pistachio: fix mfio84-89 function description and pinmux.")
Signed-off-by: James Hartley <james.hartley@imgtec.com>
Reviewed-by: Sifan Naeem <Sifan.Naeem@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e870e948f upstream.
When dm-crypt processes writes, it allocates a new bio in
crypt_alloc_buffer(). The bio is allocated from a bio set and it can
have at most BIO_MAX_PAGES vector entries, however the incoming bio can be
larger (e.g. if it was allocated by bcache). If the incoming bio is
larger, bio_alloc_bioset() fails and an error is returned.
To avoid the error, we test for a too large bio in the function
crypt_map() and use dm_accept_partial_bio() to split the bio.
dm_accept_partial_bio() trims the current bio to the desired size and
asks DM core to send another bio with the rest of the data.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a5d60783df upstream.
Move log_one_block()'s atomic_inc(&lc->io_blocks) before bio_alloc() to
fix a bug that the target hangs if bio_alloc() fails. The error path
does put_io_block(lc), so atomic_inc(&lc->io_blocks) must occur before
invoking the error path to avoid underflow of lc->io_blocks.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d0be84ec0 upstream.
If crypt_alloc_tfms() had to allocate multiple tfms and it failed before
the last allocation, then it would call crypt_free_tfms() and could free
pointers from uninitialized memory -- due to the crypt_free_tfms() check
for non-zero cc->tfms[i]. Fix by allocating zeroed memory.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 91e630d9ae upstream.
The kthread_run() function returns either a valid task_struct or
ERR_PTR() value, check for NULL is invalid. This change fixes potential
for oops, e.g. in OOM situation.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b928466b21 upstream.
The code setting XP watchpoint comparator and mask registers should, in
order to be fully compliant with specification, zero one or more most
significant bits of each field. In both L cases it means zeroing bit 63.
The bitmask doing this was wrong, though, zeroing bit 60 instead.
Fortunately, due to a lucky coincidence, this turned out to be fairly
innocent with the existing hardware.
Fixed now.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b7c1beb278 upstream.
Fuzzing the CCN perf driver revealed a small but definitely dangerous
mistake in the event setup code. When a cycle counter is requested, the
driver should not reconfigure the events bus at all, otherwise it will
corrupt (in most but the simplest cases) its configuration and may end
up accessing XP array out of its bounds and corrupting control
registers.
Reported-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e486cba28 upstream.
The "Miscellaneous Node" fell through cracks of node initialisation,
as its ID is shared with HN-I.
This patch treats MN as a special case (which it is), adding separate
validation check for it and pre-defining the node ID in relevant events
descriptions. That way one can simply run:
# perf stat -a -e ccn/mn_ecbarrier/ <workload>
Additionally, direction in the MN pseudo-events XP watchpoint
definitions is corrected to be "TX" (1) as they are defined from the
crosspoint point of view (thus barriers are transmitted from XP to MN).
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 153b58ea93 upstream.
The gpmc ranges property for NAND at CS0 was being overridden by later
includes that defined gpmc ethernet nodes, effectively breaking NAND on
these systems:
omap-gpmc 6e000000.gpmc: /ocp/gpmc@6e000000/nand@0,0 has
malformed 'reg' property
Instead of redefining the NAND range in every such dtsi, define all
currently used ranges in omap3-overo-base.dtsi.
Fixes: 98ce6007ef ("ARM: dts: overo: Support PoP NAND")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e0568dfbf upstream.
The gpmc ranges property for NAND at CS0 has been broken since it was
first added.
This currently prevents the nand gpmc child node from being probed:
omap-gpmc 6e000000.gpmc: /ocp/gpmc@6e000000/nand@0,0 has
malformed 'reg' property
and consequently the NAND device from being registered.
Fixes: 98ce6007ef ("ARM: dts: overo: Support PoP NAND")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d9fd3c9181 upstream.
Currently, the ports as seen from the rear number as:
eth0 sfp lan5 lan4 lan3 lan2 lan1 lan6
which is illogical - this came about because the rev 2.0 boards have the
LEDs on the front for the DSA switch (lan5-1) reversed. Rev 2.1 boards
fixed the LED issue, and the Clearfog case numbers the lan ports
increasing from left to right.
Maintaining this illogical numbering causes confusion, with reports that
"my link isn't coming up" and "my connection negotiates 10base-Half"
both of which are due to people thinking that the port next to the SFP
is lan1.
Fix this by renumbering the ports to match people's expectations.
[gregory.clement@free-electrons.com: added the Fixes and stable tags]
Fixes: 4c945e8556 ("ARM: dts: Add SolidRun Armada 388 Clearfog A1 DT
file")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f065e9e4ad upstream.
Commit 833f2cbf70 ("ARM: dts: imx6: change the core clock of spdif")
changed many more clocks than only the SPDIF core clock as stated in
the commit message.
The MLB clock has been added and this causes SPDIF regression as
reported by Xavi Drudis Ferran and also in this forum post:
https://forum.digikey.com/thread/34240
The MX6Q Reference Manual does not mention that MLB is a clock related
to SPDIF, so change it back to a dummy clock to restore SPDIF
functionality.
Thanks to Ambika for providing the fix at:
https://community.nxp.com/thread/387131
Fixes: 833f2cbf70 ("ARM: dts: imx6: change the core clock of spdif")
Reported-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c721da1d05 upstream.
While converting PCIe node on kirkwood by using label, the following
commit eb13cf8345 ("ARM: dts: kirkwood: Fixup pcie DT warnings")
introduced a regression on the OpenRD boards: the PCIe didn't work
anymore. As reported by Aaro Koskinen, the display/framebuffer was
lost. This commit adds the forgotten label.
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Fixes: eb13cf8345 ("ARM: dts: kirkwood: Fixup pcie DT warnings")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b46211d6dc upstream.
Add missing sysconfig/sysstatus information
to OMAP3 hwmod. The information has been
checked against OMAP34xx and OMAP36xx TRM.
Without this change DSI block is not reset
during boot, which is required for working
Nokia N950 display.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8aade778f7 upstream.
i.MX6SX has bypass PMIC ready function, as this function
is normally NOT enabled on the board design, so we need
to bypass the PMIC ready pin check during DSM mode resume
flow, otherwise, the internal DSM resume logic will be
waiting for this signal to be ready forever and cause
resume fail.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Fixes: ff843d621b ("ARM: imx: add suspend support for i.mx6sx")
Tested-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f5a49057c7 upstream.
There is a missing BM_CLPCR_BYP_MMDC_CH0_LPM_HS setting for imx6ul,
without it, the "standby" mode can't work well, the system can't be
resumed.
With this commit, the "standby" mode works well.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Cc: Anson Huang <anson.huang@nxp.com>
Fixes: ee4a5f838c ("ARM: imx: add suspend/resume support for i.mx6ul")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b00ccf5b68 upstream.
pruss hwmod RSTST register wrongly points to PWRSTCTRL register in case of
am43xx. Fix the RSTST register offset value.
This can lead to setting of wrong power state values for PER domain.
Fixes: 1c7e224d ("ARM: OMAP2+: hwmod: AM335x: runtime register update")
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 06f4e94898 upstream.
A new task inherits cpus_allowed and mems_allowed masks from its parent,
but if someone changes cpuset's config by writing to cpuset.cpus/cpuset.mems
before this new task is inserted into the cgroup's task list, the new task
won't be updated accordingly.
Signed-off-by: Zefan Li <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1423661fed upstream.
The ethtool_ops .get_regs function attempts to read the nonexistent
register NIC_QSET_SQ_0_7_CNM_CHG, which produces a "bus error" type
OOPs.
Fix by not attempting to read, and removing the definition of,
NIC_QSET_SQ_0_7_CNM_CHG. A zero is written into the register dump to
keep the layout unchanged.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3e423945ea upstream.
In commit 8ead9dd547 ("devpts: more pty driver interface cleanups") I
made devpts_get_priv() just return the dentry->fs_data directly. And
because I thought it wouldn't happen, I added a warning if you ever saw
a pts node that wasn't on devpts.
And no, that warning never triggered under any actual real use, but you
can trigger it by creating nonsensical pts nodes by hand.
So just revert the warning, and make devpts_get_priv() return NULL for
that case like it used to.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: "Eric W Biederman" <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 08c5cd3748 upstream.
Some full-speed mceusb infrared transceivers contain invalid endpoint
descriptors for their interrupt endpoints, with bInterval set to 0.
In the past they have worked out okay with the mceusb driver, because
the driver sets the bInterval field in the descriptor to 1,
overwriting whatever value may have been there before. However, this
approach was never sanctioned by the USB core, and in fact it does not
work with xHCI controllers, because they use the bInterval value that
was present when the configuration was installed.
Currently usbcore uses 32 ms as the default interval if the value in
the endpoint descriptor is invalid. It turns out that these IR
transceivers don't work properly unless the interval is set to 10 ms
or below. To work around this mceusb problem, this patch changes the
endpoint-descriptor parsing routine, making the default interval value
be 10 ms rather than 32 ms.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Wade Berrier <wberrier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e9d2850a8 upstream.
The STiH4{07,10} platform contains some interconnect clocks which are used
by various IPs. If this clock isn't handled correctly by ST's EHCI/OHCI
drivers, their hub won't be found, the following error be shown and the
result will be non-working USB:
[ 97.221963] hub 2-1:1.0: hub_ext_port_status failed (err = -110)
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f3c4fb6d0 upstream.
Problems with the signal integrity of the high speed USB data lines or
noise on reference ground lines can cause the i.MX6 USB controller to
violate USB specs and exhibit unexpected behavior.
It was observed that USBi_UI interrupts were triggered first and when
isr_setup_status_phase was called, ci->status was NULL, which lead to a
NULL pointer dereference kernel panic.
This patch fixes the kernel panic, emits a warning once and returns
-EPIPE to halt the device and let the host get stalled.
It also adds a comment to point people, who are experiencing this issue,
to their USB hardware design.
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 519d8bd4b5 upstream.
The previous driver is possible to stop the transfer wrongly.
For example:
1) An interrupt happens, but not BRDY interruption.
2) Read INTSTS0. And than state->intsts0 is not set to BRDY.
3) BRDY is set to 1 here.
4) Read BRDYSTS.
5) Clear the BRDYSTS. And then. the BRDY is cleared wrongly.
Remarks:
- The INTSTS0.BRDY is read only.
- If any bits of BRDYSTS are set to 1, the BRDY is set to 1.
- If BRDYSTS is 0, the BRDY is set to 0.
So, this patch adds condition to avoid such situation. (And about
NRDYSTS, this is not used for now. But, avoiding any side effects,
this patch doesn't touch it.)
Fixes: d5c6a1e024 ("usb: renesas_usbhs: fixup interrupt status clear method")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b2f1eaaee5 upstream.
This driver should clear the bit. Otherwise, the VBUS will output
wrongly if the usb port on a board has VBUS output capability.
Fixes: 746bfe63bb ("usb: gadget: renesas_usb3: add support for
Renesas USB3.0 peripheral controller")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f190fd9245 upstream.
This patch adds support for Infineon flashloader 0x8087/0x0801.
The flashloader is used in Telit LE940B modem family with Telit
flashing application.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c8d192428f upstream.
Added devices ids for acces i/o products quad and octal serial cards
that make use of existing Pericom PI7C9X7954 and PI7C9X7958
configurations .
Signed-off-by: Jimi Damon <jdamon@accesio.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 47b34d2ef2 upstream.
Since the commit c1a67b48f6 ("serial: 8250_pci: replace switch-case by
formula for Intel MID"), the 8250 driver crashes in the byt_set_termios()
function with a divide error. This is caused by the fact that a baud rate of 0
(B0) is not handled properly. Fix it by falling back to B9600 in this case.
Reported-by: "Mendez Salinas, Fernando" <fernando.mendez.salinas@intel.com>
Fixes: c1a67b48f6 ("serial: 8250_pci: replace switch-case by formula for Intel MID")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5dba4b14ba upstream.
A recent fix to iio_buffer_read_first_n_outer removed ret from being set by
a return from wait_event_interruptible and also added a continue in a loop
which causes the variable ret to not be set when it reaches the end of the
loop. Fix this by initializing ret to zero.
Also remove extraneous white space at the end of the loop.
Fixes: fcf68f3c0b ("fix sched WARNING "do not call blocking ops when !TASK_RUNNING")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 171c009183 upstream.
7985e7c100 ("iio: Introduce a new fractional value type") introduced a
new IIO_VAL_FRACTIONAL value type meant to represent rational type numbers
expressed by a numerator and denominator combination.
Formating of IIO_VAL_FRACTIONAL values relies upon do_div() usage. This
fails handling negative values properly since parameters are reevaluated
as unsigned values.
Fix this by using div_s64_rem() instead. Computed integer part will carry
properly signed value. Formatted fractional part will always be positive.
Fixes: 7985e7c100 ("iio: Introduce a new fractional value type")
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 307fe9dd11 upstream.
All the scaling of the KXSD9 involves multiplication with a
fraction number < 1.
However the scaling value returned from IIO_INFO_SCALE was
unpredictable as only the micros of the value was assigned, and
not the integer part, resulting in scaling like this:
$cat in_accel_scale
-1057462640.011978
Fix this by assigning zero to the integer part.
Tested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c50084093 upstream.
In at least one known setup, the chip comes up in a state where reading
the chip ID returns garbage unless it's been reset, due to noise on the
wires during system boot.
All supported chips have the same reset method, and based on the
datasheets they all need 1.3 or 1.8ms to recover after reset. So, do
the conservative thing here and always reset the chip.
Signed-off-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0d9dcf8523 upstream.
Replace the i2c_smbus_read_byte commmands used to retrieve the sensor
data with an i2c_master_recv command.
The smbus read byte method fails because the device does not expect a
stop condition after sending the first byte. When we issue the second
read, we are getting the first byte again. Net effect is that of the 14
bits used for the measurement, the 8 most significant bits are correct,
the lower 6 are not.
None of the smbus read protocols follow the pattern this device requires
(S Addr Rd [A] Data [A] Data NA P), hence the switch to an i2c receive
transaction.
Applicable from original introduction of this driver, but will require
backporting due to churn in the code.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2ab447454 upstream.
The driver always assumes that an input device has been created when
reading channel 3. This causes a kernel panic when dereferencing
st->ts_input.
The change was introduced in
commit 84882b0603 ("iio: adc: at91_adc: Add support for touchscreens
without TSMR"). Earlier versions only entered that part of the if-else
statement if only the following flags are set:
AT91_ADC_IER_XRDY | AT91_ADC_IER_YRDY | AT91_ADC_IER_PRDY
Signed-off-by: Anders Darander <anders@chargestorm.se>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d3cc21dab upstream.
The data buffer for captured mode for the ad799x driver is allocated in the
update_scan_mode() callback. This callback is not set in the iio_info
struct for the ad7791/ad7995/ad7999, which means that the data buffer is
not allocated when a captured transfer is started. As a result the driver
crashes when the first sample is received. To fix this properly set the
update_scan_mode() callback.
Fixes: d8dca33027 ("staging:iio:ad799x: Preallocate sample buffer")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 522caebb2c upstream.
The call to i2c_get_clientdata(client) returns a struct iio_dev*, not
the needed struct ads1015_data*. We need here an intermediate step as
in the function: void ads1015_get_channels_config(struct i2c_client *client).
Signed-off-by: Giorgio Dal Molin <giorgio.nicole@arcor.de>
Fixes: ecc24e72f4 ("iio: adc: Add TI ADS1015 ADC driver support")
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7175cce1c3 upstream.
Now that open delay and sample delay for each channel is configurable
via DT, the default IDLE_TIMEOUT value is not enough as this is
calculated based on hardcoded macros. This results in driver returning
EBUSY sometimes. Fix this by increasing the timeout
value based on maximum value possible to open delay and sample delays
for each channel.
Fixes: 5dc11e8106 ("iio: adc: ti_am335x_adc: make sample delay, open delay, averaging DT parameters")
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 90c43ec699 upstream.
It is possible that two or more ADC channels can be simultaneously
requested for raw samples, in which case there can be race in access to
FIFO data resulting in loss of samples.
If am335x_tsc_se_set_once() is called again from tiadc_read_raw(), when
ADC is still acquired to sample one of the channels, the second process
might be put into uninterruptible sleep state. Fix these issues, by
protecting FIFO access and channel configurations with a mutex. Since
tiadc_read_raw() might take anywhere between few microseconds to few
milliseconds to finish execution (depending on averaging and delay
values supplied via DT), its better to use mutex instead of spinlock.
Fixes: 7ca6740cd1 ("mfd: input: iio: ti_amm335x: Rework TSC/ADC synchronization")
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b2f0c09664 upstream.
Use the IS_ENABLED() helper macro to ensure that the configfs group is
initialized either when configfs is built-in or when configfs is built as a
module. Otherwise software trigger creation will result in undefined
behaviour when configfs is built as a mdoule since the configfs group for
the trigger is not properly initialized.
Fixes: b662f809d4 ("iio: core: Introduce IIO software triggers")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ac61a062f upstream.
Any readings from the raw interface of the KXSD9 driver will
return an empty string, because it does not return
IIO_VAL_INT but rather some random value from the accelerometer
to the caller.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b0eaf4506f upstream.
When userspace sends KVM_SET_LAPIC, KVM schedules a check between
the vCPU's IRR and ISR and the IOAPIC redirection table, in order
to re-establish the IOAPIC's dest_map (the list of CPUs servicing
the real-time clock interrupt with the corresponding vectors).
However, __rtc_irq_eoi_tracking_restore_one was forgetting to
set dest_map->vectors. Because of this, the IOAPIC did not process
the real-time clock interrupt EOI, ioapic->rtc_status.pending_eoi
got stuck at a non-zero value, and further RTC interrupts were
reported to userspace as coalesced.
Fixes: 9e4aabe2bb
Fixes: 4d99ba898d
Cc: Joerg Roedel <jroedel@suse.de>
Cc: David Gilbert <dgilbert@redhat.com>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 293f293637 upstream.
On arm/arm64, we depend on the kvm_unmap_hva* callbacks (via
mmu_notifiers::invalidate_*) to unmap the stage2 pagetables when
the userspace buffer gets unmapped. However, when the Hypervisor
process exits without explicit unmap of the guest buffers, the only
notifier we get is kvm_arch_flush_shadow_all() (via mmu_notifier::release
) which does nothing on arm. Later this causes us to access pages that
were already released [via exit_mmap() -> unmap_vmas()] when we actually
get to unmap the stage2 pagetable [via kvm_arch_destroy_vm() ->
kvm_free_stage2_pgd()]. This triggers crashes with CONFIG_DEBUG_PAGEALLOC,
which unmaps any free'd pages from the linear map.
[ 757.644120] Unable to handle kernel paging request at virtual address
ffff800661e00000
[ 757.652046] pgd = ffff20000b1a2000
[ 757.655471] [ffff800661e00000] *pgd=00000047fffe3003, *pud=00000047fcd8c003,
*pmd=00000047fcc7c003, *pte=00e8004661e00712
[ 757.666492] Internal error: Oops: 96000147 [#3] PREEMPT SMP
[ 757.672041] Modules linked in:
[ 757.675100] CPU: 7 PID: 3630 Comm: qemu-system-aar Tainted: G D
4.8.0-rc1 #3
[ 757.683240] Hardware name: AppliedMicro X-Gene Mustang Board/X-Gene Mustang Board,
BIOS 3.06.15 Aug 19 2016
[ 757.692938] task: ffff80069cdd3580 task.stack: ffff8006adb7c000
[ 757.698840] PC is at __flush_dcache_area+0x1c/0x40
[ 757.703613] LR is at kvm_flush_dcache_pmd+0x60/0x70
[ 757.708469] pc : [<ffff20000809dbdc>] lr : [<ffff2000080b4a70>] pstate: 20000145
...
[ 758.357249] [<ffff20000809dbdc>] __flush_dcache_area+0x1c/0x40
[ 758.363059] [<ffff2000080b6748>] unmap_stage2_range+0x458/0x5f0
[ 758.368954] [<ffff2000080b708c>] kvm_free_stage2_pgd+0x34/0x60
[ 758.374761] [<ffff2000080b2280>] kvm_arch_destroy_vm+0x20/0x68
[ 758.380570] [<ffff2000080aa330>] kvm_put_kvm+0x210/0x358
[ 758.385860] [<ffff2000080aa524>] kvm_vm_release+0x2c/0x40
[ 758.391239] [<ffff2000082ad234>] __fput+0x114/0x2e8
[ 758.396096] [<ffff2000082ad46c>] ____fput+0xc/0x18
[ 758.400869] [<ffff200008104658>] task_work_run+0x108/0x138
[ 758.406332] [<ffff2000080dc8ec>] do_exit+0x48c/0x10e8
[ 758.411363] [<ffff2000080dd5fc>] do_group_exit+0x6c/0x130
[ 758.416739] [<ffff2000080ed924>] get_signal+0x284/0xa18
[ 758.421943] [<ffff20000808a098>] do_signal+0x158/0x860
[ 758.427060] [<ffff20000808aad4>] do_notify_resume+0x6c/0x88
[ 758.432608] [<ffff200008083624>] work_pending+0x10/0x14
[ 758.437812] Code: 9ac32042 8b010001 d1000443 8a230000 (d50b7e20)
This patch fixes the issue by moving the kvm_free_stage2_pgd() to
kvm_arch_flush_shadow_all().
Tested-by: Itaru Kitayama <itaru.kitayama@riken.jp>
Reported-by: Itaru Kitayama <itaru.kitayama@riken.jp>
Reported-by: James Morse <james.morse@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a7d4b8f256 upstream.
As the meaning of these variables and pointers seems to change more
frequently, let's directly access our save area, instead of going via
current->thread.
Right now, this is broken for set/get_fpu. They simply overwrite the
host registers, as the pointers to the current save area were turned
into the static host save area.
Fixes: 3f6813b9a5 ("s390/fpu: allocate 'struct fpu' with the task_struct")
Reported-by: Hao QingFeng <haoqf@linux.vnet.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 15301a5707 upstream.
Łukasz Daniluk reported that on a RHEL kernel that his machine would lock up
after enabling function tracer. I asked him to bisect the functions within
available_filter_functions, which he did and it came down to three:
_paravirt_nop(), _paravirt_ident_32() and _paravirt_ident_64()
It was found that this is only an issue when noreplace-paravirt is added
to the kernel command line.
This means that those functions are most likely called within critical
sections of the funtion tracer, and must not be traced.
In newer kenels _paravirt_nop() is defined within gcc asm(), and is no
longer an issue. But both _paravirt_ident_{32,64}() causes the
following splat when they are traced:
mm/pgtable-generic.c:33: bad pmd ffff8800d2435150(0000000001d00054)
mm/pgtable-generic.c:33: bad pmd ffff8800d3624190(0000000001d00070)
mm/pgtable-generic.c:33: bad pmd ffff8800d36a5110(0000000001d00054)
mm/pgtable-generic.c:33: bad pmd ffff880118eb1450(0000000001d00054)
NMI watchdog: BUG: soft lockup - CPU#2 stuck for 22s! [systemd-journal:469]
Modules linked in: e1000e
CPU: 2 PID: 469 Comm: systemd-journal Not tainted 4.6.0-rc4-test+ #513
Hardware name: Hewlett-Packard HP Compaq Pro 6300 SFF/339A, BIOS K01 v02.05 05/07/2012
task: ffff880118f740c0 ti: ffff8800d4aec000 task.ti: ffff8800d4aec000
RIP: 0010:[<ffffffff81134148>] [<ffffffff81134148>] queued_spin_lock_slowpath+0x118/0x1a0
RSP: 0018:ffff8800d4aefb90 EFLAGS: 00000246
RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffff88011eb16d40
RDX: ffffffff82485760 RSI: 000000001f288820 RDI: ffffea0000008030
RBP: ffff8800d4aefb90 R08: 00000000000c0000 R09: 0000000000000000
R10: ffffffff821c8e0e R11: 0000000000000000 R12: ffff880000200fb8
R13: 00007f7a4e3f7000 R14: ffffea000303f600 R15: ffff8800d4b562e0
FS: 00007f7a4e3d7840(0000) GS:ffff88011eb00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f7a4e3f7000 CR3: 00000000d3e71000 CR4: 00000000001406e0
Call Trace:
_raw_spin_lock+0x27/0x30
handle_pte_fault+0x13db/0x16b0
handle_mm_fault+0x312/0x670
__do_page_fault+0x1b1/0x4e0
do_page_fault+0x22/0x30
page_fault+0x28/0x30
__vfs_read+0x28/0xe0
vfs_read+0x86/0x130
SyS_read+0x46/0xa0
entry_SYSCALL_64_fastpath+0x1e/0xa8
Code: 12 48 c1 ea 0c 83 e8 01 83 e2 30 48 98 48 81 c2 40 6d 01 00 48 03 14 c5 80 6a 5d 82 48 89 0a 8b 41 08 85 c0 75 09 f3 90 8b 41 08 <85> c0 74 f7 4c 8b 09 4d 85 c9 74 08 41 0f 18 09 eb 02 f3 90 8b
Reported-by: Łukasz Daniluk <lukasz.daniluk@intel.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9049771f7d upstream.
track_pfn_insert() in vmf_insert_pfn_pmd() is marking dax mappings as
uncacheable rendering them impractical for application usage. DAX-pte
mappings are cached and the goal of establishing DAX-pmd mappings is to
attain more performance, not dramatically less (3 orders of magnitude).
track_pfn_insert() relies on a previous call to reserve_memtype() to
establish the expected page_cache_mode for the range. While memremap()
arranges for reserve_memtype() to be called, devm_memremap_pages() does
not. So, teach track_pfn_insert() and untrack_pfn() how to handle
tracking without a vma, and arrange for devm_memremap_pages() to
establish the write-back-cache reservation in the memtype tree.
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Nilesh Choudhury <nilesh.choudhury@oracle.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: Toshi Kani <toshi.kani@hpe.com>
Reported-by: Kai Zhang <kai.ka.zhang@oracle.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5e7101954 upstream.
Active QSFP cables were reset only every alternate iteration of the
channel tuning algorithm instead of every iteration due to incorrect
reset of the flag that controlled QSFP reset, resulting in using stale
QSFP status in the channel tuning algorithm.
Fixes: 8ebd4cf185 ("Add active and optical cable support")
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Easwar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d1e09f304a upstream.
Fixes an oops that might happen if uverbs_close races with
remove_one.
Both contexts may run ib_uverbs_cleanup_ucontext, it depends
on the flow.
Currently, there is no protection for a case that remove_one
didn't make the cleanup it runs to its end, the underlying
ib_device was freed then uverbs_close will call
ib_uverbs_cleanup_ucontext and OOPs.
Above might happen if uverbs_close deleted the file from the list
then remove_one didn't find it and runs to its end.
Fixes to protect against that case by a new cleanup lock so that
ib_uverbs_cleanup_ucontext will be called always before that
remove_one is ended.
Fixes: 35d4a0b63d ("IB/uverbs: Fix race between ib_uverbs_open and remove_one")
Reported-by: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c62fb260a8 upstream.
The qp init function does a kzalloc() while holding the RCU
lock that encounters the following warning with a debug kernel
when a cat of the qp_stats is done:
[ 231.723948] rcu_scheduler_active = 1, debug_locks = 0
[ 231.731939] 3 locks held by cat/11355:
[ 231.736492] #0: (debugfs_srcu){......}, at: [<ffffffff813001a5>] debugfs_use_file_start+0x5/0x90
[ 231.746955] #1: (&p->lock){+.+.+.}, at: [<ffffffff81289a6c>] seq_read+0x4c/0x3c0
[ 231.755873] #2: (rcu_read_lock){......}, at: [<ffffffffa0a0c535>] _qp_stats_seq_start+0x5/0xd0 [hfi1]
[ 231.766862]
The init functions do an implicit next which requires the rcu read lock
before the kzalloc().
Fix for both drivers is to change the scope of the init function to only
do the allocation and the initialization of the just allocated iter.
The implict next is moved back into the respective start functions to fix
the issue.
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 299f6230bc upstream.
v4.8-rc3 commit 99f3c90d0d ("dm flakey: error READ bios during the
down_interval") overlooked the 'drop_writes' feature, which is meant to
allow reads to be issued rather than errored, during the down_interval.
Fixes: 99f3c90d0d ("dm flakey: error READ bios during the down_interval")
Reported-by: Qu Wenruo <quwenruo@cn.fujitsu.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5efc244346 upstream.
Prior to the change the function would blindly deference mm, exe_file
and exe_file->f_inode, each of which could have been NULL or freed.
Use get_task_exe_file to safely obtain stable exe_file.
Signed-off-by: Mateusz Guzik <mguzik@redhat.com>
Acked-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Acked-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd81a9170e upstream.
For more convenient access if one has a pointer to the task.
As a minor nit take advantage of the fact that only task lock + rcu are
needed to safely grab ->exe_file. This saves mm refcount dance.
Use the helper in proc_exe_link.
Signed-off-by: Mateusz Guzik <mguzik@redhat.com>
Acked-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Acked-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b4b3f6a06 upstream.
irq already contains the interrupt number for the port, don't add the
port index to it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: d684a90d38 ("ahci: per-port msix support")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c11600e4fe upstream.
KASAN allocates memory from the page allocator as part of
kmem_cache_free(), and that can reference current->mempolicy through any
number of allocation functions. It needs to be NULL'd out before the
final reference is dropped to prevent a use-after-free bug:
BUG: KASAN: use-after-free in alloc_pages_current+0x363/0x370 at addr ffff88010b48102c
CPU: 0 PID: 15425 Comm: trinity-c2 Not tainted 4.8.0-rc2+ #140
...
Call Trace:
dump_stack
kasan_object_err
kasan_report_error
__asan_report_load2_noabort
alloc_pages_current <-- use after free
depot_save_stack
save_stack
kasan_slab_free
kmem_cache_free
__mpol_put <-- free
do_exit
This patch sets current->mempolicy to NULL before dropping the final
reference.
Link: http://lkml.kernel.org/r/alpine.DEB.2.10.1608301442180.63329@chino.kir.corp.google.com
Fixes: cd11016e5f ("mm, kasan: stackdepot implementation. Enable stackdepot for SLAB")
Signed-off-by: David Rientjes <rientjes@google.com>
Reported-by: Vegard Nossum <vegard.nossum@oracle.com>
Acked-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 070c43eea5 upstream.
If kexec_apply_relocations fails, kexec_load_purgatory frees pi->sechdrs
and pi->purgatory_buf. This is redundant, because in case of error
kimage_file_prepare_segments calls kimage_file_post_load_cleanup, which
will also free those buffers.
This causes two warnings like the following, one for pi->sechdrs and the
other for pi->purgatory_buf:
kexec-bzImage64: Loading purgatory failed
------------[ cut here ]------------
WARNING: CPU: 1 PID: 2119 at mm/vmalloc.c:1490 __vunmap+0xc1/0xd0
Trying to vfree() nonexistent vm area (ffffc90000e91000)
Modules linked in:
CPU: 1 PID: 2119 Comm: kexec Not tainted 4.8.0-rc3+ #5
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Call Trace:
dump_stack+0x4d/0x65
__warn+0xcb/0xf0
warn_slowpath_fmt+0x4f/0x60
? find_vmap_area+0x19/0x70
? kimage_file_post_load_cleanup+0x47/0xb0
__vunmap+0xc1/0xd0
vfree+0x2e/0x70
kimage_file_post_load_cleanup+0x5e/0xb0
SyS_kexec_file_load+0x448/0x680
? putname+0x54/0x60
? do_sys_open+0x190/0x1f0
entry_SYSCALL_64_fastpath+0x13/0x8f
---[ end trace 158bb74f5950ca2b ]---
Fix by setting pi->sechdrs an pi->purgatory_buf to NULL, since vfree
won't try to free a NULL pointer.
Link: http://lkml.kernel.org/r/1472083546-23683-1-git-send-email-bauerman@linux.vnet.ibm.com
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Acked-by: Baoquan He <bhe@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Dave Young <dyoung@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b519d408ea upstream.
Ensure that we conform to the algorithm described in RFC5661, section
18.36.4 for when to bump the sequence id. In essence we do it for all
cases except when the RPC call timed out, or in case of the server returning
NFS4ERR_DELAY or NFS4ERR_STALE_CLIENTID.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf0291dd22 upstream.
According to RFC5661, the client is responsible for serialising
LAYOUTGET and LAYOUTRETURN to avoid ambiguity. Consider the case
where we send both in parallel.
Client Server
====== ======
LAYOUTGET(seqid=X)
LAYOUTRETURN(seqid=X)
LAYOUTGET return seqid=X+1
LAYOUTRETURN return seqid=X+2
Process LAYOUTRETURN
Forget layout stateid
Process LAYOUTGET
Set seqid=X+1
The client processes the layoutget/layoutreturn in the wrong order,
and since the result of the layoutreturn was to clear the only
existing layout segment, the client forgets the layout stateid.
When the LAYOUTGET comes in, it is treated as having a completely
new stateid, and so the client sets the wrong sequence id...
Fix is to check if there are outstanding LAYOUTGET requests
before we send the LAYOUTRETURN (note that LAYOUGET will already
wait if it sees an outstanding LAYOUTRETURN).
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 885848186f upstream.
nfsd4_release_lockowner finds a lock owner that has no lock state,
and drops cl_lock. Then release_lockowner picks up cl_lock and
unhashes the lock owner.
During the window where cl_lock is dropped, I don't see anything
preventing a concurrent nfsd4_lock from finding that same lock owner
and adding lock state to it.
Move release_lockowner() into nfsd4_release_lockowner and hang onto
the cl_lock until after the lock owner's state cannot be found
again.
Found by inspection, we don't currently have a reproducer.
Fixes: 2c41beb0e5 ("nfsd: reduce cl_lock thrashing in ... ")
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e09c978aae upstream.
The slot table hasn't been an array since v3.7. Ensure that we
use nfs4_lookup_slot() to access the slot correctly.
Fixes: 87dda67e73 ("NFSv4.1: Allow SEQUENCE to resize the slot table...")
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b88fa69eaa upstream.
Ensure that the client conforms to the normative behaviour described in
RFC5661 Section 12.7.2: "If a client believes its lease has expired,
it MUST NOT send I/O to the storage device until it has validated its
lease."
So ensure that we wait for the lease to be validated before using
the layout.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3dc147359e upstream.
If the attempt to connect to a DS fails inside ff_layout_pg_init_read or
ff_layout_pg_init_write, then we currently end up clearing the layout
segment carried by the struct nfs_pageio_descriptor, causing an Oops
when we later call into ff_layout_read_pagelist/ff_layout_write_pagelist.
The fix is to ensure we return the layout and then retry.
Fixes: 446ca21953 ("pNFS/flexfiles: When initing reads or writes, we...")
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df6a58c5c5 upstream.
kernfs_notify_workfn() sends out file modified events for the
scheduled kernfs_nodes. Because the modifications aren't from
userland, it doesn't have the matching file struct at hand and can't
use fsnotify_modify(). Instead, it looked up the inode and then used
d_find_any_alias() to find the dentry and used fsnotify_parent() and
fsnotify() directly to generate notifications.
The assumption was that the relevant dentries would have been pinned
if there are listeners, which isn't true as inotify doesn't pin
dentries at all and watching the parent doesn't pin the child dentries
even for dnotify. This led to, for example, inotify watchers not
getting notifications if the system is under memory pressure and the
matching dentries got reclaimed. It can also be triggered through
/proc/sys/vm/drop_caches or a remount attempt which involves shrinking
dcache.
fsnotify_parent() only uses the dentry to access the parent inode,
which kernfs can do easily. Update kernfs_notify_workfn() so that it
uses fsnotify() directly for both the parent and target inodes without
going through d_find_any_alias(). While at it, supply the target file
name to fsnotify() from kernfs_node->name.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Evgeny Vereshchagin <evvers@ya.ru>
Fixes: d911d98748 ("kernfs: make kernfs_notify() trigger inotify events too")
Cc: John McCutchan <john@johnmccutchan.com>
Cc: Robert Love <rlove@rlove.org>
Cc: Eric Paris <eparis@parisplace.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit caa58f8088 upstream.
In pnv_ioda_free_pe(), the PE object (including the associated PE
number) is cleared before resetting the corresponding bit in the
PE allocation bitmap. It means PE#0 is always released to the bitmap
wrongly.
This fixes above issue by caching the PE number before the PE object
is cleared.
Fixes: 1e9167726c ("powerpc/powernv: Use PE instead of number during setup and release"
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f077aaf075 upstream.
In commit c60ac5693c ("powerpc: Update kernel VSID range", 2013-03-13)
we lost a check on the region number (the top four bits of the effective
address) for addresses below PAGE_OFFSET. That commit replaced a check
that the top 18 bits were all zero with a check that bits 46 - 59 were
zero (performed for all addresses, not just user addresses).
This means that userspace can access an address like 0x1000_0xxx_xxxx_xxxx
and we will insert a valid SLB entry for it. The VSID used will be the
same as if the top 4 bits were 0, but the page size will be some random
value obtained by indexing beyond the end of the mm_ctx_high_slices_psize
array in the paca. If that page size is the same as would be used for
region 0, then userspace just has an alias of the region 0 space. If the
page size is different, then no HPTE will be found for the access, and
the process will get a SIGSEGV (since hash_page_mm() will refuse to create
a HPTE for the bogus address).
The access beyond the end of the mm_ctx_high_slices_psize can be at most
5.5MB past the array, and so will be in RAM somewhere. Since the access
is a load performed in real mode, it won't fault or crash the kernel.
At most this bug could perhaps leak a little bit of information about
blocks of 32 bytes of memory located at offsets of i * 512kB past the
paca->mm_ctx_high_slices_psize array, for 1 <= i <= 11.
Fixes: c60ac5693c ("powerpc: Update kernel VSID range")
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a9cbf0b219 upstream.
In a situation, where Linux kernel gets notified about duplicate error log
from OPAL, it is been observed that kernel fails to remove sysfs entries
(/sys/firmware/opal/elog/0xXXXXXXXX) of such error logs. This is because,
we currently search the error log/dump kobject in the kset list via
'kset_find_obj()' routine. Which eventually increment the reference count
by one, once it founds the kobject.
So, unless we decrement the reference count by one after it found the kobject,
we would not be able to release the kobject properly later.
This patch adds the 'kobject_put()' which was missing earlier.
Signed-off-by: Mukesh Ojha <mukesh02@linux.vnet.ibm.com>
Reviewed-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc7786d3ee upstream.
tabort_syscall runs with RI=1, so a nested recoverable machine
check will load the paca into r13 and overwrite what we loaded
it with, because exceptions returning to privileged mode do not
restore r13.
Fixes: b4b56f9eca (powerpc/tm: Abort syscalls in active transactions)
Signed-off-by: Nick Piggin <npiggin@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit db7196a0d0 ]
Commit 76174004a0
(tcp: do not slow start when cwnd equals ssthresh )
introduced regression in TCP YeAH. Using 100ms delay 1% loss virtual
ethernet link kernel 4.2 shows bandwidth ~500KB/s for single TCP
connection and kernel 4.3 and above (including 4.8-rc4) shows bandwidth
~100KB/s.
That is caused by stalled cwnd when cwnd equals ssthresh. This patch
fixes it by proper increasing cwnd in this case.
Signed-off-by: Artem Germanov <agermanov@anchorfree.com>
Acked-by: Dmitry Adamushko <d.adamushko@anchorfree.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cd17d230dd ]
Currently vlan tagged packets were not parsed correctly
and assumed to be regular IPv4/IPv6 packets.
We should check for 802.1Q/802.1ad tags and update the lro header
accordingly.
This fixes the use case where LRO is on and rxvlan is off
(vlan stripping is off).
Fixes: e586b3b0ba ('net/mlx5: Ethernet Datapath files')
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 76061f631c ]
When DATA and/or FIN are carried in a SYN/ACK message or SYN message,
we append an skb in socket receive queue, but we forget to call
sk_forced_mem_schedule().
Effect is that the socket has a negative sk->sk_forward_alloc as long as
the message is not read by the application.
Josh Hunt fixed a similar issue in commit d22e153718 ("tcp: fix tcp
fin memory accounting")
Fixes: 168a8f5805 ("tcp: TCP Fast Open Server - main code path")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Josh Hunt <johunt@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 751eb6b604 ]
In general, when DAD detected IPv6 duplicate address, ifp->state
will be set to INET6_IFADDR_STATE_ERRDAD and DAD is stopped by a
delayed work, the call tree should be like this:
ndisc_recv_ns
-> addrconf_dad_failure <- missing ifp put
-> addrconf_mod_dad_work
-> schedule addrconf_dad_work()
-> addrconf_dad_stop() <- missing ifp hold before call it
addrconf_dad_failure() called with ifp refcont holding but not put.
addrconf_dad_work() call addrconf_dad_stop() without extra holding
refcount. This will not cause any issue normally.
But the race between addrconf_dad_failure() and addrconf_dad_work()
may cause ifp refcount leak and netdevice can not be unregister,
dmesg show the following messages:
IPv6: eth0: IPv6 duplicate address fe80::XX:XXXX:XXXX:XX detected!
...
unregister_netdevice: waiting for eth0 to become free. Usage count = 1
Cc: stable@vger.kernel.org
Fixes: c15b1ccadb ("ipv6: move DAD and addrconf_verify processing
to workqueue")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9d13744bb7 ]
There is a code path where we are calling __iowrite64_copy() on
an address that is not 64-bit aligned. This causes an exception on
some architectures such as arm64. Fix that code path by using
__iowrite32_copy().
Reported-by: JD Zheng <jiandong.zheng@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 03c2778a93 ]
Neither the failure or success paths of ping_v6_sendmsg release
the dst it acquires. This leads to a flood of warnings from
"net/core/dst.c:288 dst_release" on older kernels that
don't have 8bf4ada2e2 backported.
That patch optimistically hoped this had been fixed post 3.10, but
it seems at least one case wasn't, where I've seen this triggered
a lot from machines doing unprivileged icmp sockets.
Cc: Martin Lau <kafai@fb.com>
Signed-off-by: Dave Jones <davej@codemonkey.org.uk>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6e1ce3c345 ]
Right now we use the 'readlock' both for protecting some of the af_unix
IO path and for making the bind be single-threaded.
The two are independent, but using the same lock makes for a nasty
deadlock due to ordering with regards to filesystem locking. The bind
locking would want to nest outside the VSF pathname locking, but the IO
locking wants to nest inside some of those same locks.
We tried to fix this earlier with commit c845acb324 ("af_unix: Fix
splice-bind deadlock") which moved the readlock inside the vfs locks,
but that caused problems with overlayfs that will then call back into
filesystem routines that take the lock in the wrong order anyway.
Splitting the locks means that we can go back to having the bind lock be
the outermost lock, and we don't have any deadlocks with lock ordering.
Acked-by: Rainer Weikusat <rweikusat@cyberadapt.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 38f7bd94a9 ]
This reverts commit c845acb324.
It turns out that it just replaces one deadlock with another one: we can
still get the wrong lock ordering with the readlock due to overlayfs
calling back into the filesystem layer and still taking the vfs locks
after the readlock.
The proper solution ends up being to just split the readlock into two
pieces: the bind lock (taken *outside* the vfs locks) and the IO lock
(taken *inside* the filesystem locks). The two locks are independent
anyway.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 24b27fc4cd ]
Following few steps will crash kernel -
(a) Create bonding master
> modprobe bonding miimon=50
(b) Create macvlan bridge on eth2
> ip link add link eth2 dev mvl0 address aa:0:0:0:0:01 \
type macvlan
(c) Now try adding eth2 into the bond
> echo +eth2 > /sys/class/net/bond0/bonding/slaves
<crash>
Bonding does lots of things before checking if the device enslaved is
busy or not.
In this case when the notifier call-chain sends notifications, the
bond_netdev_event() assumes that the rx_handler /rx_handler_data is
registered while the bond_enslave() hasn't progressed far enough to
register rx_handler for the new slave.
This patch adds a rx_handler check that can be performed right at the
beginning of the enslave code to avoid getting into this situation.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c0338aff22 ]
Dmitry reported a double free on kcm socket, which could
be easily reproduced by:
#include <unistd.h>
#include <sys/syscall.h>
int main()
{
int fd = syscall(SYS_socket, 0x29ul, 0x5ul, 0x0ul, 0, 0, 0);
syscall(SYS_ioctl, fd, 0x89e2ul, 0x20a98000ul, 0, 0, 0);
return 0;
}
This is because on the error path, after we install
the new socket file, we call sock_release() to clean
up the socket, which leaves the fd pointing to a freed
socket. Fix this by calling sys_close() on that fd
directly.
Fixes: ab7ac4eb98 ("kcm: Kernel Connection Multiplexor module")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9264251ee2 ]
commit bc8c20acae ("bridge: multicast: treat igmpv3 report with
INCLUDE and no sources as a leave") seems to have accidentally reverted
commit 47cc84ce0c ("bridge: fix parsing of MLDv2 reports"). This
commit brings back a change to br_ip6_multicast_mld2_report() where
parsing of MLDv2 reports stops when the first group is successfully
added to the MDB cache.
Fixes: bc8c20acae ("bridge: multicast: treat igmpv3 report with INCLUDE and no sources as a leave")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2fb04fdf30 ]
Commit b70661c708 ("net: smc91x: use run-time configuration on all ARM
machines") broke some ARM platforms through several mistakes. Firstly,
the access size must correspond to the following rule:
(a) at least one of 16-bit or 8-bit access size must be supported
(b) 32-bit accesses are optional, and may be enabled in addition to
the above.
Secondly, it provides no emulation of 16-bit accesses, instead blindly
making 16-bit accesses even when the platform specifies that only 8-bit
is supported.
Reorganise smc91x.h so we can make use of the existing 16-bit access
emulation already provided - if 16-bit accesses are supported, use
16-bit accesses directly, otherwise if 8-bit accesses are supported,
use the provided 16-bit access emulation. If neither, BUG(). This
exactly reflects the driver behaviour prior to the commit being fixed.
Since the conversion incorrectly cut down the available access sizes on
several platforms, we also need to go through every platform and fix up
the overly-restrictive access size: Arnd assumed that if a platform can
perform 32-bit, 16-bit and 8-bit accesses, then only a 32-bit access
size needed to be specified - not so, all available access sizes must
be specified.
This likely fixes some performance regressions in doing this: if a
platform does not support 8-bit accesses, 8-bit accesses have been
emulated by performing a 16-bit read-modify-write access.
Tested on the Intel Assabet/Neponset platform, which supports only 8-bit
accesses, which was broken by the original commit.
Fixes: b70661c708 ("net: smc91x: use run-time configuration on all ARM machines")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c3e70edd7c ]
This reverts:
commit 33c133cc75 ("phy: IRQ cannot be shared")
On hardware with multiple PHY devices hooked up to the same IRQ line, allow
them to share it.
Sergei Shtylyov says:
"I'm not sure now what was the reason I concluded that the IRQ sharing
was impossible... most probably I thought that the kernel IRQ handling
code exited the loop over the IRQ actions once IRQ_HANDLED was returned
-- which is obviously not so in reality..."
Signed-off-by: Xander Huff <xander.huff@ni.com>
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4f101c4779 ]
We kept shadow copies of which interrupt sources we have enabled and
disabled, but due to an order bug in how intrl2_mask_clear was defined,
we could run into the following scenario:
CPU0 CPU1
intrl2_1_mask_clear(..)
sets INTRL2_CPU_MASK_CLEAR
bcm_sf2_switch_1_isr
read INTRL2_CPU_STATUS and masks with stale
irq1_mask value
updates irq1_mask value
Which would make us loop again and again trying to process and interrupt
we are not clearing since our copy of whether it was enabled before
still indicates it was not. Fix this by updating the shadow copy first,
and then unasking at the HW level.
Fixes: 246d7f773c ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7b996243fa ]
Instead of using sock_tx_timestamp, use skb_tx_timestamp to record
software transmit timestamp of a packet.
sock_tx_timestamp resets and overrides the tx_flags of the skb.
The function is intended to be called from within the protocol
layer when creating the skb, not from a device driver. This is
inconsistent with other drivers and will cause issues for TCP.
In TCP, we intend to sample the timestamps for the last byte
for each sendmsg/sendpage. For that reason, tcp_sendmsg calls
tcp_tx_timestamp only with the last skb that it generates.
For example, if a 128KB message is split into two 64KB packets
we want to sample the SND timestamp of the last packet. The current
code in the tun driver, however, will result in sampling the SND
timestamp for both packets.
Also, when the last packet is split into smaller packets for
retranmission (see tcp_fragment), the tun driver will record
timestamps for all of the retransmitted packets and not only the
last packet.
Fixes: eda2977291 (tun: Support software transmit time stamping.)
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Francis Yan <francisyyan@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 232cb53a45 ]
The function sctp_diag_dump_one() currently performs a memcpy()
of 64 bytes from a 16 byte field into another 16 byte field. Fix
by using correct size, use sizeof to obtain correct size instead
of using a hard-coded constant.
Fixes: 8f840e47f1 ("sctp: add the sctp_diag.c file")
Signed-off-by: Lance Richardson <lrichard@redhat.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e83c6744e8 ]
Laura tracked poll() [and friends] regression caused by commit
e6afc8ace6 ("udp: remove headers from UDP packets before queueing")
udp_poll() needs to know if there is a valid packet in receive queue,
even if its payload length is 0.
Change first_packet_length() to return an signed int, and use -1
as the indication of an empty queue.
Fixes: e6afc8ace6 ("udp: remove headers from UDP packets before queueing")
Reported-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 28a10c426e ]
Encoding of the metadata was using the padded length as opposed to
the real length of the data which is a bug per specification.
This has not been an issue todate because all metadatum specified
so far has been 32 bit where aligned and data length are the same width.
This also includes a bug fix for validating the length of a u16 field.
But since there is no metadata of size u16 yes we are fine to include it
here.
While at it get rid of magic numbers.
Fixes: ef6980b6be ("net sched: introduce IFE action")
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1dbd0d373a ]
The wrong key is used when extracting the address type field set by
the flower offload code. We have to use the control key and not the
basic key, fix that.
Fixes: e3a2b7ed01 ('net/mlx5e: Support offload cls_flower with drop action')
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2c0f8ce1b5 ]
Set and verify signature calculates the signature for each of the
mailbox nodes, even for those that are unused (from cache). Added
a missing length check to set and verify only those which are used.
While here, also moved the setting of msg's nodes token to where we
already go over them. This saves a pass because checksum is disabled,
and the only useful thing remaining that set signature does is setting
the token.
Fixes: e126ba97db ('mlx5: Add driver for Mellanox Connect-IB
adapters')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1061c90f52 ]
When PCI error is detected we should save the state of the pci prior to
disabling it.
Also when receiving pci slot reset call we need to verify that the
device is responsive.
Fixes: 89d44f0a6c ('net/mlx5_core: Add pci error handlers to mlx5_core
driver')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bb1fceca22 ]
When tcp_sendmsg() allocates a fresh and empty skb, it puts it at the
tail of the write queue using tcp_add_write_queue_tail()
Then it attempts to copy user data into this fresh skb.
If the copy fails, we undo the work and remove the fresh skb.
Unfortunately, this undo lacks the change done to tp->highest_sack and
we can leave a dangling pointer (to a freed skb)
Later, tcp_xmit_retransmit_queue() can dereference this pointer and
access freed memory. For regular kernels where memory is not unmapped,
this might cause SACK bugs because tcp_highest_sack_seq() is buggy,
returning garbage instead of tp->snd_nxt, but with various debug
features like CONFIG_DEBUG_PAGEALLOC, this can crash the kernel.
This bug was found by Marco Grassi thanks to syzkaller.
Fixes: 6859d49475 ("[TCP]: Abstract tp->highest_sack accessing & point to next skb")
Reported-by: Marco Grassi <marco.gra@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bc561632dd ]
If IPv6 is disabled when the option is set to keep IPv6
addresses on link down, userspace is unaware of this as
there is no such indication via netlink. The solution is to
remove the IPv6 addresses in this case, which results in
netlink messages indicating removal of addresses in the
usual manner. This fix also makes the behavior consistent
with the case of having IPv6 disabled first, which stops
IPv6 addresses from being added.
Fixes: f1705ec197 ("net: ipv6: Make address flushing on ifdown optional")
Signed-off-by: Mike Manning <mmanning@brocade.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 54236ab09e ]
sctp_transport_seq_start() does not currently clear iter->start_fail on
success, but relies on it being zero when it is allocated (by
seq_open_net()).
This can be a problem in the following sequence:
open() // allocates iter (and implicitly sets iter->start_fail = 0)
read()
- iter->start() // fails and sets iter->start_fail = 1
- iter->stop() // doesn't call sctp_transport_walk_stop() (correct)
read() again
- iter->start() // succeeds, but doesn't change iter->start_fail
- iter->stop() // doesn't call sctp_transport_walk_stop() (wrong)
We should initialize sctp_ht_iter::start_fail to zero if ->start()
succeeds, otherwise it's possible that we leave an old value of 1 there,
which will cause ->stop() to not call sctp_transport_walk_stop(), which
causes all sorts of problems like not calling rcu_read_unlock() (and
preempt_enable()), eventually leading to more warnings like this:
BUG: sleeping function called from invalid context at mm/slab.h:388
in_atomic(): 0, irqs_disabled(): 0, pid: 16551, name: trinity-c2
Preemption disabled at:[<ffffffff819bceb6>] rhashtable_walk_start+0x46/0x150
[<ffffffff81149abb>] preempt_count_add+0x1fb/0x280
[<ffffffff83295892>] _raw_spin_lock+0x12/0x40
[<ffffffff819bceb6>] rhashtable_walk_start+0x46/0x150
[<ffffffff82ec665f>] sctp_transport_walk_start+0x2f/0x60
[<ffffffff82edda1d>] sctp_transport_seq_start+0x4d/0x150
[<ffffffff81439e50>] traverse+0x170/0x850
[<ffffffff8143aeec>] seq_read+0x7cc/0x1180
[<ffffffff814f996c>] proc_reg_read+0xbc/0x180
[<ffffffff813d0384>] do_loop_readv_writev+0x134/0x210
[<ffffffff813d2a95>] do_readv_writev+0x565/0x660
[<ffffffff813d6857>] vfs_readv+0x67/0xa0
[<ffffffff813d6c16>] do_preadv+0x126/0x170
[<ffffffff813d710c>] SyS_preadv+0xc/0x10
[<ffffffff8100334c>] do_syscall_64+0x19c/0x410
[<ffffffff83296225>] return_from_SYSCALL_64+0x0/0x6a
[<ffffffffffffffff>] 0xffffffffffffffff
Notice that this is a subtly different stacktrace from the one in commit
5fc382d875 ("net/sctp: terminate rhashtable walk correctly").
Cc: Xin Long <lucien.xin@gmail.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Acked-By: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5ba092efc7 ]
If iriap_register_lsap() fails to allocate memory, self->lsap is
set to NULL. However, none of the callers handle the failure and
irlmp_connect_request() will happily dereference it:
iriap_register_lsap: Unable to allocated LSAP!
================================================================================
UBSAN: Undefined behaviour in net/irda/irlmp.c:378:2
member access within null pointer of type 'struct lsap_cb'
CPU: 1 PID: 15403 Comm: trinity-c0 Not tainted 4.8.0-rc1+ #81
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.9.3-0-ge2fc41e-prebuilt.qemu-project.org
04/01/2014
0000000000000000 ffff88010c7e78a8 ffffffff82344f40 0000000041b58ab3
ffffffff84f98000 ffffffff82344e94 ffff88010c7e78d0 ffff88010c7e7880
ffff88010630ad00 ffffffff84a5fae0 ffffffff84d3f5c0 000000000000017a
Call Trace:
[<ffffffff82344f40>] dump_stack+0xac/0xfc
[<ffffffff8242f5a8>] ubsan_epilogue+0xd/0x8a
[<ffffffff824302bf>] __ubsan_handle_type_mismatch+0x157/0x411
[<ffffffff83b7bdbc>] irlmp_connect_request+0x7ac/0x970
[<ffffffff83b77cc0>] iriap_connect_request+0xa0/0x160
[<ffffffff83b77f48>] state_s_disconnect+0x88/0xd0
[<ffffffff83b78904>] iriap_do_client_event+0x94/0x120
[<ffffffff83b77710>] iriap_getvaluebyclass_request+0x3e0/0x6d0
[<ffffffff83ba6ebb>] irda_find_lsap_sel+0x1eb/0x630
[<ffffffff83ba90c8>] irda_connect+0x828/0x12d0
[<ffffffff833c0dfb>] SYSC_connect+0x22b/0x340
[<ffffffff833c7e09>] SyS_connect+0x9/0x10
[<ffffffff81007bd3>] do_syscall_64+0x1b3/0x4b0
[<ffffffff845f946a>] entry_SYSCALL64_slow_path+0x25/0x25
================================================================================
The bug seems to have been around since forever.
There's more problems with missing error checks in iriap_init() (and
indeed all of irda_init()), but that's a bigger problem that needs
very careful review and testing. This patch will fix the most serious
bug (as it's easily reached from unprivileged userspace).
I have tested my patch with a reproducer.
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0ed661d5a4 ]
Fix the bpf_try_make_writable() helper and all call sites we have in BPF,
it's currently defect with regards to skbs when the write_len spans into
non-linear parts, no matter if cloned or not.
There are multiple issues at once. First, using skb_store_bits() is not
correct since even if we have a cloned skb, page frags can still be shared.
To really make them private, we need to pull them in via __pskb_pull_tail()
first, which also gets us a private head via pskb_expand_head() implicitly.
This is for helpers like bpf_skb_store_bytes(), bpf_l3_csum_replace(),
bpf_l4_csum_replace(). Really, the only thing reasonable and working here
is to call skb_ensure_writable() before any write operation. Meaning, via
pskb_may_pull() it makes sure that parts we want to access are pulled in and
if not does so plus unclones the skb implicitly. If our write_len still fits
the headlen and we're cloned and our header of the clone is not writable,
then we need to make a private copy via pskb_expand_head(). skb_store_bits()
is a bit misleading and only safe to store into non-linear data in different
contexts such as 357b40a18b ("[IPV6]: IPV6_CHECKSUM socket option can
corrupt kernel memory").
For above BPF helper functions, it means after fixed bpf_try_make_writable(),
we've pulled in enough, so that we operate always based on skb->data. Thus,
the call to skb_header_pointer() and skb_store_bits() becomes superfluous.
In bpf_skb_store_bytes(), the len check is unnecessary too since it can
only pass in maximum of BPF stack size, so adding offset is guaranteed to
never overflow. Also bpf_l3/4_csum_replace() helpers must test for proper
offset alignment since they use __sum16 pointer for writing resulting csum.
The remaining helpers that change skb data not discussed here yet are
bpf_skb_vlan_push(), bpf_skb_vlan_pop() and bpf_skb_change_proto(). The
vlan helpers internally call either skb_ensure_writable() (pop case) and
skb_cow_head() (push case, for head expansion), respectively. Similarly,
bpf_skb_proto_xlat() takes care to not mangle page frags.
Fixes: 608cd71a9c ("tc: bpf: generalize pedit action")
Fixes: 91bc4822c3 ("tc: bpf: add checksum helpers")
Fixes: 3697649ff2 ("bpf: try harder on clones when writing into skb")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a5d0dc810a ]
When executing the script included below, the netns delete operation
hangs with the following message (repeated at 10 second intervals):
kernel:unregister_netdevice: waiting for lo to become free. Usage count = 1
This occurs because a reference to the lo interface in the "secure" netns
is still held by a dst entry in the xfrm bundle cache in the init netns.
Address this problem by garbage collecting the tunnel netns flow cache
when a cross-namespace vti interface receives a NETDEV_DOWN notification.
A more detailed description of the problem scenario (referencing commands
in the script below):
(1) ip link add vti_test type vti local 1.1.1.1 remote 1.1.1.2 key 1
The vti_test interface is created in the init namespace. vti_tunnel_init()
attaches a struct ip_tunnel to the vti interface's netdev_priv(dev),
setting the tunnel net to &init_net.
(2) ip link set vti_test netns secure
The vti_test interface is moved to the "secure" netns. Note that
the associated struct ip_tunnel still has tunnel->net set to &init_net.
(3) ip netns exec secure ping -c 4 -i 0.02 -I 192.168.100.1 192.168.200.1
The first packet sent using the vti device causes xfrm_lookup() to be
called as follows:
dst = xfrm_lookup(tunnel->net, skb_dst(skb), fl, NULL, 0);
Note that tunnel->net is the init namespace, while skb_dst(skb) references
the vti_test interface in the "secure" namespace. The returned dst
references an interface in the init namespace.
Also note that the first parameter to xfrm_lookup() determines which flow
cache is used to store the computed xfrm bundle, so after xfrm_lookup()
returns there will be a cached bundle in the init namespace flow cache
with a dst referencing a device in the "secure" namespace.
(4) ip netns del secure
Kernel begins to delete the "secure" namespace. At some point the
vti_test interface is deleted, at which point dst_ifdown() changes
the dst->dev in the cached xfrm bundle flow from vti_test to lo (still
in the "secure" namespace however).
Since nothing has happened to cause the init namespace's flow cache
to be garbage collected, this dst remains attached to the flow cache,
so the kernel loops waiting for the last reference to lo to go away.
<Begin script>
ip link add br1 type bridge
ip link set dev br1 up
ip addr add dev br1 1.1.1.1/8
ip netns add secure
ip link add vti_test type vti local 1.1.1.1 remote 1.1.1.2 key 1
ip link set vti_test netns secure
ip netns exec secure ip link set vti_test up
ip netns exec secure ip link s lo up
ip netns exec secure ip addr add dev lo 192.168.100.1/24
ip netns exec secure ip route add 192.168.200.0/24 dev vti_test
ip xfrm policy flush
ip xfrm state flush
ip xfrm policy add dir out tmpl src 1.1.1.1 dst 1.1.1.2 \
proto esp mode tunnel mark 1
ip xfrm policy add dir in tmpl src 1.1.1.2 dst 1.1.1.1 \
proto esp mode tunnel mark 1
ip xfrm state add src 1.1.1.1 dst 1.1.1.2 proto esp spi 1 \
mode tunnel enc des3_ede 0x112233445566778811223344556677881122334455667788
ip xfrm state add src 1.1.1.2 dst 1.1.1.1 proto esp spi 1 \
mode tunnel enc des3_ede 0x112233445566778811223344556677881122334455667788
ip netns exec secure ping -c 4 -i 0.02 -I 192.168.100.1 192.168.200.1
ip netns del secure
<End script>
Reported-by: Hangbin Liu <haliu@redhat.com>
Reported-by: Jan Tluka <jtluka@redhat.com>
Signed-off-by: Lance Richardson <lrichard@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1f415a74b0 ]
Using per-register incrementing ID can lead to
find_good_pkt_pointers() confusing registers which
have completely different values. Consider example:
0: (bf) r6 = r1
1: (61) r8 = *(u32 *)(r6 +76)
2: (61) r0 = *(u32 *)(r6 +80)
3: (bf) r7 = r8
4: (07) r8 += 32
5: (2d) if r8 > r0 goto pc+9
R0=pkt_end R1=ctx R6=ctx R7=pkt(id=0,off=0,r=32) R8=pkt(id=0,off=32,r=32) R10=fp
6: (bf) r8 = r7
7: (bf) r9 = r7
8: (71) r1 = *(u8 *)(r7 +0)
9: (0f) r8 += r1
10: (71) r1 = *(u8 *)(r7 +1)
11: (0f) r9 += r1
12: (07) r8 += 32
13: (2d) if r8 > r0 goto pc+1
R0=pkt_end R1=inv56 R6=ctx R7=pkt(id=0,off=0,r=32) R8=pkt(id=1,off=32,r=32) R9=pkt(id=1,off=0,r=32) R10=fp
14: (71) r1 = *(u8 *)(r9 +16)
15: (b7) r7 = 0
16: (bf) r0 = r7
17: (95) exit
We need to get a UNKNOWN_VALUE with imm to force id
generation so lines 0-5 make r7 a valid packet pointer.
We then read two different bytes from the packet and
add them to copies of the constructed packet pointer.
r8 (line 9) and r9 (line 11) will get the same id of 1,
independently. When either of them is validated (line
13) - find_good_pkt_pointers() will also mark the other
as safe. This leads to access on line 14 being mistakenly
considered safe.
Fixes: 969bf05eb3 ("bpf: direct packet access")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ba63f23d69 upstream.
Since setting an encryption policy requires writing metadata to the
filesystem, it should be guarded by mnt_want_write/mnt_drop_write.
Otherwise, a user could cause a write to a frozen or readonly
filesystem. This was handled correctly by f2fs but not by ext4. Make
fscrypt_process_policy() handle it rather than relying on the filesystem
to get it right.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Acked-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ba913e4f72 upstream.
When mapping a page into the guest we error check using is_error_pfn(),
however this doesn't detect a value of KVM_PFN_NOSLOT, indicating an
error HVA for the page. This can only happen on MIPS right now due to
unusual memslot management (e.g. being moved / removed / resized), or
with an Enhanced Virtual Memory (EVA) configuration where the default
KVM_HVA_ERR_* and kvm_is_error_hva() definitions are unsuitable (fixed
in a later patch). This case will be treated as a pfn of zero, mapping
the first page of physical memory into the guest.
It would appear the MIPS KVM port wasn't updated prior to being merged
(in v3.10) to take commit 81c52c56e2 ("KVM: do not treat noslot pfn as
a error pfn") into account (merged v3.8), which converted a bunch of
is_error_pfn() calls to is_error_noslot_pfn(). Switch to using
is_error_noslot_pfn() instead to catch this case properly.
Fixes: 858dd5d457 ("KVM/MIPS32: MMU/TLB operations for the Guest.")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[james.hogan@imgtec.com: Backport to v4.7.y]
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b53e7d000d upstream.
The bootloader (U-boot) sometimes uses this timer for various delays.
It uses it as a ongoing counter, and does comparisons on the current
counter value. The timer counter is never stopped.
In some cases when the user interacts with the bootloader, or lets
it idle for some time before loading Linux, the timer may expire,
and an interrupt will be pending. This results in an unexpected
interrupt when the timer interrupt is enabled by the kernel, at
which point the event_handler isn't set yet. This results in a NULL
pointer dereference exception, panic, and no way to reboot.
Clear any pending interrupts after we stop the timer in the probe
function to avoid this.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a87eeb900d upstream.
Commit 655ee63cf3 ("scsi constants: command, sense key + additional
sense string") added a "Completed" sense string with key 0xF to
snstext[], but failed to updated the upper bounds check of the sense key
in scsi_sense_key_string().
Fixes: 655ee63cf3 ("[SCSI] scsi constants: command, sense key + additional sense strings")
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9f8a7658bc upstream.
When a user timer instance is continued without the explicit start
beforehand, the system gets eventually zero-division error like:
divide error: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN
CPU: 1 PID: 27320 Comm: syz-executor Not tainted 4.8.0-rc3-next-20160825+ #8
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
task: ffff88003c9b2280 task.stack: ffff880027280000
RIP: 0010:[<ffffffff858e1a6c>] [< inline >] ktime_divns include/linux/ktime.h:195
RIP: 0010:[<ffffffff858e1a6c>] [<ffffffff858e1a6c>] snd_hrtimer_callback+0x1bc/0x3c0 sound/core/hrtimer.c:62
Call Trace:
<IRQ>
[< inline >] __run_hrtimer kernel/time/hrtimer.c:1238
[<ffffffff81504335>] __hrtimer_run_queues+0x325/0xe70 kernel/time/hrtimer.c:1302
[<ffffffff81506ceb>] hrtimer_interrupt+0x18b/0x420 kernel/time/hrtimer.c:1336
[<ffffffff8126d8df>] local_apic_timer_interrupt+0x6f/0xe0 arch/x86/kernel/apic/apic.c:933
[<ffffffff86e13056>] smp_apic_timer_interrupt+0x76/0xa0 arch/x86/kernel/apic/apic.c:957
[<ffffffff86e1210c>] apic_timer_interrupt+0x8c/0xa0 arch/x86/entry/entry_64.S:487
<EOI>
.....
Although a similar issue was spotted and a fix patch was merged in
commit [6b760bb2c6: ALSA: timer: fix division by zero after
SNDRV_TIMER_IOCTL_CONTINUE], it seems covering only a part of
iceberg.
In this patch, we fix the issue a bit more drastically. Basically the
continue of an uninitialized timer is supposed to be a fresh start, so
we do it for user timers. For the direct snd_timer_continue() call,
there is no way to pass the initial tick value, so we kick out for the
uninitialized case.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 11749e086b upstream.
I got this with syzkaller:
==================================================================
BUG: KASAN: null-ptr-deref on address 0000000000000020
Read of size 32 by task syz-executor/22519
CPU: 1 PID: 22519 Comm: syz-executor Not tainted 4.8.0-rc2+ #169
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.9.3-0-ge2fc41e-prebuilt.qemu-project.org 04/01/2
014
0000000000000001 ffff880111a17a00 ffffffff81f9f141 ffff880111a17a90
ffff880111a17c50 ffff880114584a58 ffff880114584a10 ffff880111a17a80
ffffffff8161fe3f ffff880100000000 ffff880118d74a48 ffff880118d74a68
Call Trace:
[<ffffffff81f9f141>] dump_stack+0x83/0xb2
[<ffffffff8161fe3f>] kasan_report_error+0x41f/0x4c0
[<ffffffff8161ff74>] kasan_report+0x34/0x40
[<ffffffff82c84b54>] ? snd_timer_user_read+0x554/0x790
[<ffffffff8161e79e>] check_memory_region+0x13e/0x1a0
[<ffffffff8161e9c1>] kasan_check_read+0x11/0x20
[<ffffffff82c84b54>] snd_timer_user_read+0x554/0x790
[<ffffffff82c84600>] ? snd_timer_user_info_compat.isra.5+0x2b0/0x2b0
[<ffffffff817d0831>] ? proc_fault_inject_write+0x1c1/0x250
[<ffffffff817d0670>] ? next_tgid+0x2a0/0x2a0
[<ffffffff8127c278>] ? do_group_exit+0x108/0x330
[<ffffffff8174653a>] ? fsnotify+0x72a/0xca0
[<ffffffff81674dfe>] __vfs_read+0x10e/0x550
[<ffffffff82c84600>] ? snd_timer_user_info_compat.isra.5+0x2b0/0x2b0
[<ffffffff81674cf0>] ? do_sendfile+0xc50/0xc50
[<ffffffff81745e10>] ? __fsnotify_update_child_dentry_flags+0x60/0x60
[<ffffffff8143fec6>] ? kcov_ioctl+0x56/0x190
[<ffffffff81e5ada2>] ? common_file_perm+0x2e2/0x380
[<ffffffff81746b0e>] ? __fsnotify_parent+0x5e/0x2b0
[<ffffffff81d93536>] ? security_file_permission+0x86/0x1e0
[<ffffffff816728f5>] ? rw_verify_area+0xe5/0x2b0
[<ffffffff81675355>] vfs_read+0x115/0x330
[<ffffffff81676371>] SyS_read+0xd1/0x1a0
[<ffffffff816762a0>] ? vfs_write+0x4b0/0x4b0
[<ffffffff82001c2c>] ? __this_cpu_preempt_check+0x1c/0x20
[<ffffffff8150455a>] ? __context_tracking_exit.part.4+0x3a/0x1e0
[<ffffffff816762a0>] ? vfs_write+0x4b0/0x4b0
[<ffffffff81005524>] do_syscall_64+0x1c4/0x4e0
[<ffffffff810052fc>] ? syscall_return_slowpath+0x16c/0x1d0
[<ffffffff83c3276a>] entry_SYSCALL64_slow_path+0x25/0x25
==================================================================
There are a couple of problems that I can see:
- ioctl(SNDRV_TIMER_IOCTL_SELECT), which potentially sets
tu->queue/tu->tqueue to NULL on memory allocation failure, so read()
would get a NULL pointer dereference like the above splat
- the same ioctl() can free tu->queue/to->tqueue which means read()
could potentially see (and dereference) the freed pointer
We can fix both by taking the ioctl_lock mutex when dereferencing
->queue/->tqueue, since that's always held over all the ioctl() code.
Just looking at the code I find it likely that there are more problems
here such as tu->qhead pointing outside the buffer if the size is
changed concurrently using SNDRV_TIMER_IOCTL_PARAMS.
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fd06c77eb9 upstream.
The subwoofer on Inspiron 7559 was disabled originally.
Applying a pin fixup to node 0x1b can enable it and make it work.
Old pin: 0x411111f0
New pin: 0x90170151
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 816f318b23 upstream.
When a seq-virmidi driver is initialized, it registers a rawmidi
instance with its callback to create an associated seq kernel client.
Currently it's done throughly in rawmidi's register_mutex context.
Recently it was found that this may lead to a deadlock another rawmidi
device that is being attached with the sequencer is accessed, as both
open with the same register_mutex. This was actually triggered by
syzkaller, as Dmitry Vyukov reported:
======================================================
[ INFO: possible circular locking dependency detected ]
4.8.0-rc1+ #11 Not tainted
-------------------------------------------------------
syz-executor/7154 is trying to acquire lock:
(register_mutex#5){+.+.+.}, at: [<ffffffff84fd6d4b>] snd_rawmidi_kernel_open+0x4b/0x260 sound/core/rawmidi.c:341
but task is already holding lock:
(&grp->list_mutex){++++.+}, at: [<ffffffff850138bb>] check_and_subscribe_port+0x5b/0x5c0 sound/core/seq/seq_ports.c:495
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&grp->list_mutex){++++.+}:
[<ffffffff8147a3a8>] lock_acquire+0x208/0x430 kernel/locking/lockdep.c:3746
[<ffffffff863f6199>] down_read+0x49/0xc0 kernel/locking/rwsem.c:22
[< inline >] deliver_to_subscribers sound/core/seq/seq_clientmgr.c:681
[<ffffffff85005c5e>] snd_seq_deliver_event+0x35e/0x890 sound/core/seq/seq_clientmgr.c:822
[<ffffffff85006e96>] > snd_seq_kernel_client_dispatch+0x126/0x170 sound/core/seq/seq_clientmgr.c:2418
[<ffffffff85012c52>] snd_seq_system_broadcast+0xb2/0xf0 sound/core/seq/seq_system.c:101
[<ffffffff84fff70a>] snd_seq_create_kernel_client+0x24a/0x330 sound/core/seq/seq_clientmgr.c:2297
[< inline >] snd_virmidi_dev_attach_seq sound/core/seq/seq_virmidi.c:383
[<ffffffff8502d29f>] snd_virmidi_dev_register+0x29f/0x750 sound/core/seq/seq_virmidi.c:450
[<ffffffff84fd208c>] snd_rawmidi_dev_register+0x30c/0xd40 sound/core/rawmidi.c:1645
[<ffffffff84f816d3>] __snd_device_register.part.0+0x63/0xc0 sound/core/device.c:164
[< inline >] __snd_device_register sound/core/device.c:162
[<ffffffff84f8235d>] snd_device_register_all+0xad/0x110 sound/core/device.c:212
[<ffffffff84f7546f>] snd_card_register+0xef/0x6c0 sound/core/init.c:749
[<ffffffff85040b7f>] snd_virmidi_probe+0x3ef/0x590 sound/drivers/virmidi.c:123
[<ffffffff833ebf7b>] platform_drv_probe+0x8b/0x170 drivers/base/platform.c:564
......
-> #0 (register_mutex#5){+.+.+.}:
[< inline >] check_prev_add kernel/locking/lockdep.c:1829
[< inline >] check_prevs_add kernel/locking/lockdep.c:1939
[< inline >] validate_chain kernel/locking/lockdep.c:2266
[<ffffffff814791f4>] __lock_acquire+0x4d44/0x4d80 kernel/locking/lockdep.c:3335
[<ffffffff8147a3a8>] lock_acquire+0x208/0x430 kernel/locking/lockdep.c:3746
[< inline >] __mutex_lock_common kernel/locking/mutex.c:521
[<ffffffff863f0ef1>] mutex_lock_nested+0xb1/0xa20 kernel/locking/mutex.c:621
[<ffffffff84fd6d4b>] snd_rawmidi_kernel_open+0x4b/0x260 sound/core/rawmidi.c:341
[<ffffffff8502e7c7>] midisynth_subscribe+0xf7/0x350 sound/core/seq/seq_midi.c:188
[< inline >] subscribe_port sound/core/seq/seq_ports.c:427
[<ffffffff85013cc7>] check_and_subscribe_port+0x467/0x5c0 sound/core/seq/seq_ports.c:510
[<ffffffff85015da9>] snd_seq_port_connect+0x2c9/0x500 sound/core/seq/seq_ports.c:579
[<ffffffff850079b8>] snd_seq_ioctl_subscribe_port+0x1d8/0x2b0 sound/core/seq/seq_clientmgr.c:1480
[<ffffffff84ffe9e4>] snd_seq_do_ioctl+0x184/0x1e0 sound/core/seq/seq_clientmgr.c:2225
[<ffffffff84ffeae8>] snd_seq_kernel_client_ctl+0xa8/0x110 sound/core/seq/seq_clientmgr.c:2440
[<ffffffff85027664>] snd_seq_oss_midi_open+0x3b4/0x610 sound/core/seq/oss/seq_oss_midi.c:375
[<ffffffff85023d67>] snd_seq_oss_synth_setup_midi+0x107/0x4c0 sound/core/seq/oss/seq_oss_synth.c:281
[<ffffffff8501b0a8>] snd_seq_oss_open+0x748/0x8d0 sound/core/seq/oss/seq_oss_init.c:274
[<ffffffff85019d8a>] odev_open+0x6a/0x90 sound/core/seq/oss/seq_oss.c:138
[<ffffffff84f7040f>] soundcore_open+0x30f/0x640 sound/sound_core.c:639
......
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&grp->list_mutex);
lock(register_mutex#5);
lock(&grp->list_mutex);
lock(register_mutex#5);
*** DEADLOCK ***
======================================================
The fix is to simply move the registration parts in
snd_rawmidi_dev_register() to the outside of the register_mutex lock.
The lock is needed only to manage the linked list, and it's not
necessarily to cover the whole initialization process.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b1ca4bcad upstream.
In hwdep interface of fireworks driver, accessing to user space is in a
critical section with disabled local interrupt. Depending on architecture,
accessing to user space can cause page fault exception. Then local
processor stores machine status and handles the synchronous event. A
handler corresponding to the event can call task scheduler to wait for
preparing pages. In a case of usage of single core processor, the state to
disable local interrupt is worse because it don't handle usual interrupts
from hardware.
This commit fixes this bug, performing the accessing outside spinlock. This
commit also gives up counting the number of queued response messages to
simplify ring-buffer management.
Reported-by: Vaishali Thakkar <vaishali.thakkar@oracle.com>
Fixes: 555e8a8f7f14('ALSA: fireworks: Add command/response functionality into hwdep interface')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 04b2d9c9c3 upstream.
In hwdep interface of firewire-tascam driver, accessing to user space is
in a critical section with disabled local interrupt. Depending on
architecture, accessing to user space can cause page fault exception. Then
local processor stores machine status and handle the synchronous event. A
handler corresponding to the event can call task scheduler to wait for
preparing pages. In a case of usage of single core processor, the state to
disable local interrupt is worse because it doesn't handle usual interrupts
from hardware.
This commit fixes this bug, by performing the accessing outside spinlock.
Reported-by: Vaishali Thakkar <vaishali.thakkar@oracle.com>
Fixes: e5e0c3dd257b('ALSA: firewire-tascam: add hwdep interface')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 83d9956b7e upstream.
Avoid getting sample rate on B850V3 CP2114 as it is unsupported and
causes noisy "current rate is different from the runtime rate" messages
when playback starts.
Signed-off-by: Ken Lin <ken.lin@advantech.com.tw>
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 002ced4be6 upstream.
The FS_IOC_SET_ENCRYPTION_POLICY ioctl allowed setting an encryption
policy on nondirectory files. This was unintentional, and in the case
of nonempty regular files did not behave as expected because existing
data was not actually encrypted by the ioctl.
In the case of ext4, the user could also trigger filesystem errors in
->empty_dir(), e.g. due to mismatched "directory" checksums when the
kernel incorrectly tried to interpret a regular file as a directory.
This bug affected ext4 with kernels v4.8-rc1 or later and f2fs with
kernels v4.6 and later. It appears that older kernels only permitted
directories and that the check was accidentally lost during the
refactoring to share the file encryption code between ext4 and f2fs.
This patch restores the !S_ISDIR() check that was present in older
kernels.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 163ae1c6ad upstream.
On an ext4 or f2fs filesystem with file encryption supported, a user
could set an encryption policy on any empty directory(*) to which they
had readonly access. This is obviously problematic, since such a
directory might be owned by another user and the new encryption policy
would prevent that other user from creating files in their own directory
(for example).
Fix this by requiring inode_owner_or_capable() permission to set an
encryption policy. This means that either the caller must own the file,
or the caller must have the capability CAP_FOWNER.
(*) Or also on any regular file, for f2fs v4.6 and later and ext4
v4.8-rc1 and later; a separate bug fix is coming for that.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b18e2359a upstream.
For algorithms that implement IV generators before the crypto ops,
the IV needed for decryption is initially located in req->src
scatterlist, not in req->iv.
Avoid copying the IV into req->iv by modifying the (givdecrypt)
descriptors to load it directly from req->src.
aead_givdecrypt() is no longer needed and goes away.
Fixes: 479bcc7c5b ("crypto: caam - Convert authenc to new AEAD interface")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 564471d2f2 upstream.
Clean up: FMR is about to replace the rpcrdma_map_one code with
scatterlists. Move the scatterlist fields out of the FRWR-specific
union and into the generic part of rpcrdma_mw.
One minor change: -EIO is now returned if FRWR registration fails.
The RPC is terminated immediately, since the problem is likely due
to a software bug, thus retrying likely won't help.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a77ec83a57 upstream.
The address of the iovec &vq->iov[out] is not guaranteed to contain the scsi
command's response iovec throughout the lifetime of the command. Rather, it
is more likely to contain an iovec from an immediately following command
after looping back around to vhost_get_vq_desc(). Pass along the iovec
entirely instead.
Fixes: 79c14141a4 ("vhost/scsi: Convert completion path to use copy_to_iter")
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2564970a38 upstream.
If an IRQ is setup using __setup_irq(), which is used by the
request_irq() family of functions, and we are using an SMP kernel then
the affinity of the IRQ will be set via setup_affinity() immediately
after the IRQ is enabled. This call to gic_set_affinity() will lead to
the interrupt being mapped to a VPE. However there are other ways to use
IRQs which don't cause affinity to be set, for example if it is used to
chain to another IRQ controller with irq_set_chained_handler_and_data().
The irq_set_chained_handler_and_data() code path will enable the IRQ,
but will not trigger a call to gic_set_affinity() and in this case
nothing will map the interrupt to a VPE, meaning that the interrupt is
never received.
Fix this by implementing the activate operation for the GIC device IRQ
domain, using gic_shared_irq_domain_map() to map the interrupt to the
correct pin of cpu 0.
Fixes: c98c1822ee ("irqchip/mips-gic: Add device hierarchy domain")
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Link: http://lkml.kernel.org/r/20160819170715.27820-2-paul.burton@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6a33fa2b87 upstream.
gic_shared_irq_domain_map() is called from gic_irq_domain_alloc() where
the wrong chip has been set, and is then overwritten. Tidy this up by
setting the correct chip the first time, and setting the
handle_level_irq handler from gic_irq_domain_alloc() too.
gic_shared_irq_domain_map() is also called from gic_irq_domain_map(),
which now calls irq_set_chip_and_handler() to retain its previous
behaviour.
This patch prepares for a follow-on which will call
gic_shared_irq_domain_map() from a callback where the lock on the struct
irq_desc is held, which without this change would cause the call to
irq_set_chip_and_handler() to lead to a deadlock.
Fixes: c98c1822ee ("irqchip/mips-gic: Add device hierarchy domain")
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Link: http://lkml.kernel.org/r/20160819170715.27820-1-paul.burton@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit acc9cf8c66 upstream.
This patch fixes a cachedev registration-time allocation deadlock.
This can deadlock on boot if your initrd auto-registeres bcache devices:
Allocator thread:
[ 720.727614] INFO: task bcache_allocato:3833 blocked for more than 120 seconds.
[ 720.732361] [<ffffffff816eeac7>] schedule+0x37/0x90
[ 720.732963] [<ffffffffa05192b8>] bch_bucket_alloc+0x188/0x360 [bcache]
[ 720.733538] [<ffffffff810e6950>] ? prepare_to_wait_event+0xf0/0xf0
[ 720.734137] [<ffffffffa05302bd>] bch_prio_write+0x19d/0x340 [bcache]
[ 720.734715] [<ffffffffa05190bf>] bch_allocator_thread+0x3ff/0x470 [bcache]
[ 720.735311] [<ffffffff816ee41c>] ? __schedule+0x2dc/0x950
[ 720.735884] [<ffffffffa0518cc0>] ? invalidate_buckets+0x980/0x980 [bcache]
Registration thread:
[ 720.710403] INFO: task bash:3531 blocked for more than 120 seconds.
[ 720.715226] [<ffffffff816eeac7>] schedule+0x37/0x90
[ 720.715805] [<ffffffffa05235cd>] __bch_btree_map_nodes+0x12d/0x150 [bcache]
[ 720.716409] [<ffffffffa0522d30>] ? bch_btree_insert_check_key+0x1c0/0x1c0 [bcache]
[ 720.717008] [<ffffffffa05236e4>] bch_btree_insert+0xf4/0x170 [bcache]
[ 720.717586] [<ffffffff810e6950>] ? prepare_to_wait_event+0xf0/0xf0
[ 720.718191] [<ffffffffa0527d9a>] bch_journal_replay+0x14a/0x290 [bcache]
[ 720.718766] [<ffffffff810cc90d>] ? ttwu_do_activate.constprop.94+0x5d/0x70
[ 720.719369] [<ffffffff810cf684>] ? try_to_wake_up+0x1d4/0x350
[ 720.719968] [<ffffffffa05317d0>] run_cache_set+0x580/0x8e0 [bcache]
[ 720.720553] [<ffffffffa053302e>] register_bcache+0xe2e/0x13b0 [bcache]
[ 720.721153] [<ffffffff81354cef>] kobj_attr_store+0xf/0x20
[ 720.721730] [<ffffffff812a2dad>] sysfs_kf_write+0x3d/0x50
[ 720.722327] [<ffffffff812a225a>] kernfs_fop_write+0x12a/0x180
[ 720.722904] [<ffffffff81225177>] __vfs_write+0x37/0x110
[ 720.723503] [<ffffffff81228048>] ? __sb_start_write+0x58/0x110
[ 720.724100] [<ffffffff812cedb3>] ? security_file_permission+0x23/0xa0
[ 720.724675] [<ffffffff812258a9>] vfs_write+0xa9/0x1b0
[ 720.725275] [<ffffffff8102479c>] ? do_audit_syscall_entry+0x6c/0x70
[ 720.725849] [<ffffffff81226755>] SyS_write+0x55/0xd0
[ 720.726451] [<ffffffff8106a390>] ? do_page_fault+0x30/0x80
[ 720.727045] [<ffffffff816f2cae>] system_call_fastpath+0x12/0x71
The fifo code in upstream bcache can't use the last element in the buffer,
which was the cause of the bug: if you asked for a power of two size,
it'd give you a fifo that could hold one less than what you asked for
rather than allocating a buffer twice as big.
Signed-off-by: Kent Overstreet <kent.overstreet@gmail.com>
Tested-by: Eric Wheeler <bcache@linux.ewheeler.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c0082e985f upstream.
An assertion in layout_in_gaps() verifies that the gap_lebs pointer is
below the maximum bound. When computing this maximum bound the idx_lebs
count is multiplied by sizeof(int), while C pointers arithmetic does take
into account the size of the pointed elements implicitly already. Remove
the multiplication to fix the assertion.
Fixes: 1e51764a3c ("UBIFS: add new flash file system")
Signed-off-by: Vincent Stehlé <vincent.stehle@intel.com>
Cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c57cac145 upstream.
Sunrise Point PCH with SPS Firmware doesn't expose working
MEI interface, we need to quirk it out.
The SPS Firmware is identifiable only on the first PCI function
of the device.
Tested-by: Sujith Pandel <sujith_pandel@dell.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e1ff3dd1ae upstream.
Workdir creation fails in latest kernel.
Fix by allowing EOPNOTSUPP as a valid return value from
vfs_removexattr(XATTR_NAME_POSIX_ACL_*). Upper filesystem may not support
ACL and still be perfectly able to support overlayfs.
Reported-by: Martin Ziegler <ziegler@uni-freiburg.de>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Fixes: c11b9fdd6a ("ovl: remove posix_acl_default from workdir")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7cb35119d0 upstream.
Be defensive about what underlying fs provides us in the returned xattr
list buffer. If it's not properly null terminated, bail out with a warning
insead of BUG.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c11b9fdd6a upstream.
Clear out posix acl xattrs on workdir and also reset the mode after
creation so that an inherited sgid bit is cleared.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0956254a2d upstream.
When a copy up of a directory occurs which has the opaque xattr set, the
xattr remains in the upper directory. The immediate behavior with overlayfs
is that the upper directory is not treated as opaque, however after a
remount the opaque flag is used and upper directory is treated as opaque.
This causes files created in the lower layer to be hidden when using
multiple lower directories.
Fix by not copying up the opaque flag.
To reproduce:
----8<---------8<---------8<---------8<---------8<---------8<----
mkdir -p l/d/s u v w mnt
mount -t overlay overlay -olowerdir=l,upperdir=u,workdir=w mnt
rm -rf mnt/d/
mkdir -p mnt/d/n
umount mnt
mount -t overlay overlay -olowerdir=u:l,upperdir=v,workdir=w mnt
touch mnt/d/foo
umount mnt
mount -t overlay overlay -olowerdir=u:l,upperdir=v,workdir=w mnt
ls mnt/d
----8<---------8<---------8<---------8<---------8<---------8<----
output should be: "foo n"
Reported-by: Derek McGowan <dmcg@drizz.net>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=151291
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eea2fb4851 upstream.
When mounting overlayfs it needs a clean "work" directory under the
supplied workdir.
Previously the mount code removed this directory if it already existed and
created a new one. If the removal failed (e.g. directory was not empty)
then it fell back to a read-only mount not using the workdir.
While this has never been reported, it is possible to get a non-empty
"work" dir from a previous mount of overlayfs in case of crash in the
middle of an operation using the work directory.
In this case the left over state should be discarded and the overlay
filesystem will be consistent, guaranteed by the atomicity of operations on
moving to/from the workdir to the upper layer.
This patch implements cleaning out any files left in workdir. It is
implemented using real recursion for simplicity, but the depth is limited
to 2, because the worst case is that of a directory containing whiteouts
under "work".
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 27727df240 upstream.
When I added some extra sanity checking in timekeeping_get_ns() under
CONFIG_DEBUG_TIMEKEEPING, I missed that the NMI safe __ktime_get_fast_ns()
method was using timekeeping_get_ns().
Thus the locking added to the debug checks broke the NMI-safety of
__ktime_get_fast_ns().
This patch open-codes the timekeeping_get_ns() logic for
__ktime_get_fast_ns(), so can avoid any deadlocks in NMI.
Fixes: 4ca22c2648 "timekeeping: Add warnings when overflows or underflows are observed"
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Reported-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Link: http://lkml.kernel.org/r/1471993702-29148-2-git-send-email-john.stultz@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a4f8f6667f upstream.
It was reported that hibernation could fail on the 2nd attempt, where the
system hangs at hibernate() -> syscore_resume() -> i8237A_resume() ->
claim_dma_lock(), because the lock has already been taken.
However there is actually no other process would like to grab this lock on
that problematic platform.
Further investigation showed that the problem is triggered by setting
/sys/power/pm_trace to 1 before the 1st hibernation.
Since once pm_trace is enabled, the rtc becomes unmeaningful after suspend,
and meanwhile some BIOSes would like to adjust the 'invalid' RTC (e.g, smaller
than 1970) to the release date of that motherboard during POST stage, thus
after resumed, it may seem that the system had a significant long sleep time
which is a completely meaningless value.
Then in timekeeping_resume -> tk_debug_account_sleep_time, if the bit31 of the
sleep time happened to be set to 1, fls() returns 32 and we add 1 to
sleep_time_bin[32], which causes an out of bounds array access and therefor
memory being overwritten.
As depicted by System.map:
0xffffffff81c9d080 b sleep_time_bin
0xffffffff81c9d100 B dma_spin_lock
the dma_spin_lock.val is set to 1, which caused this problem.
This patch adds a sanity check in tk_debug_account_sleep_time()
to ensure we don't index past the sleep_time_bin array.
[jstultz: Problem diagnosed and original patch by Chen Yu, I've solved the
issue slightly differently, but borrowed his excelent explanation of the
issue here.]
Fixes: 5c83545f24 "power: Add option to log time spent in suspend"
Reported-by: Janek Kozicki <cosurgi@gmail.com>
Reported-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Cc: linux-pm@vger.kernel.org
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Xunlei Pang <xpang@redhat.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Zhang Rui <rui.zhang@intel.com>
Link: http://lkml.kernel.org/r/1471993702-29148-3-git-send-email-john.stultz@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f3d7ebdeb2 upstream.
From inspection, the superblock sb_inprogress check is done in the
verifier and triggered only for the primary superblock via a
"bp->b_bn == XFS_SB_DADDR" check.
Unfortunately, the primary superblock is an uncached buffer, and
hence it is configured by xfs_buf_read_uncached() with:
bp->b_bn = XFS_BUF_DADDR_NULL; /* always null for uncached buffers */
And so this check never triggers. Fix it.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3e103a6551 upstream.
commit cbaadf0f90 ("ASoC: atmel_ssc_dai: refactor the startup and
shutdown") refactored code such that the SSC is reset on every
startup; this breaks duplex audio (e.g. first start audio playback,
then start record, causing the playback to stop/hang)
Fixes: cbaadf0f90 (ASoC: atmel_ssc_dai: refactor the startup and shutdown)
Signed-off-by: Christoph Huber <c.huber@bct-electronic.com>
Signed-off-by: Peter Meerwald-Stadler <p.meerwald@bct-electronic.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 552416c146 upstream.
We'd end up NULL pointer dereferencing because we didn't take the
error path out in the parent. Fixes igt vc4_lookup_fail test.
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes: d5b1a78a77 ("drm/vc4: Add support for drawing 3D frames.")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9326e6f255 upstream.
Overflow memory handling is tricky: While it's still referenced by the
BPO registers, we want to keep it from being freed. When we are
putting a new set of overflow memory in the registers, we need to
assign the old one to the last rendering job using it.
We were looking at "what's currently running in the binner", but since
the bin/render submission split, we may end up with the binner
completing and having no new job while the renderer is still
processing. So, if we don't find a bin job at all, look at the
highest-seqno (last) render job to attach our overflow to.
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes: ca26d28bba ("drm/vc4: improve throughput by pipelining binning and rendering jobs")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d5fb46e0e3 upstream.
If you managed to exceed the limit to switch to vmalloc, we'd use the
wrong free.
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes: d5b1a78a77 ("drm/vc4: Add support for drawing 3D frames.")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f00975c61 upstream.
Somehow this one slipped through, which means drivers without modeset
support can be oopsed (since those also don't call
drm_mode_config_init, which means the crtc lookup will chase an
uninitalized idr).
Reported-by: Alexander Potapenko <glider@google.com>
Cc: Alexander Potapenko <glider@google.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit add1fa7510 upstream.
Due to assigning the 'replaced' value instead of or'ing it,
if drm_atomic_crtc_set_property() gets called multiple times,
the last call will define the color_mgmt_changed flag, so
a non-updating call to a property can reset the flag and
prevent actual hw state updates required by preceding
property updates.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is an alternative to eccf2a4e6b
which inadvertedly fixes an oops in probe by a device returning
malformed descriptors. The problem allows a malicious device to
attack the kernel.
That patch in v4.8 is too extensive to backport to stable.
Thus this alternative fix is needed up to v4.7
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reported-by: Binyamin Sharet <bsharet@cisco.com>
Tested-by: Binyamin Sharet <bsharet@cisco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 568ac88821 upstream.
cgroup_threadgroup_rwsem is acquired in read mode during process exit
and fork. It is also grabbed in write mode during
__cgroups_proc_write(). I've recently run into a scenario with lots
of memory pressure and OOM and I am beginning to see
systemd
__switch_to+0x1f8/0x350
__schedule+0x30c/0x990
schedule+0x48/0xc0
percpu_down_write+0x114/0x170
__cgroup_procs_write.isra.12+0xb8/0x3c0
cgroup_file_write+0x74/0x1a0
kernfs_fop_write+0x188/0x200
__vfs_write+0x6c/0xe0
vfs_write+0xc0/0x230
SyS_write+0x6c/0x110
system_call+0x38/0xb4
This thread is waiting on the reader of cgroup_threadgroup_rwsem to
exit. The reader itself is under memory pressure and has gone into
reclaim after fork. There are times the reader also ends up waiting on
oom_lock as well.
__switch_to+0x1f8/0x350
__schedule+0x30c/0x990
schedule+0x48/0xc0
jbd2_log_wait_commit+0xd4/0x180
ext4_evict_inode+0x88/0x5c0
evict+0xf8/0x2a0
dispose_list+0x50/0x80
prune_icache_sb+0x6c/0x90
super_cache_scan+0x190/0x210
shrink_slab.part.15+0x22c/0x4c0
shrink_zone+0x288/0x3c0
do_try_to_free_pages+0x1dc/0x590
try_to_free_pages+0xdc/0x260
__alloc_pages_nodemask+0x72c/0xc90
alloc_pages_current+0xb4/0x1a0
page_table_alloc+0xc0/0x170
__pte_alloc+0x58/0x1f0
copy_page_range+0x4ec/0x950
copy_process.isra.5+0x15a0/0x1870
_do_fork+0xa8/0x4b0
ppc_clone+0x8/0xc
In the meanwhile, all processes exiting/forking are blocked almost
stalling the system.
This patch moves the threadgroup_change_begin from before
cgroup_fork() to just before cgroup_canfork(). There is no nee to
worry about threadgroup changes till the task is actually added to the
threadgroup. This avoids having to call reclaim with
cgroup_threadgroup_rwsem held.
tj: Subject and description edits.
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Acked-by: Zefan Li <lizefan@huawei.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4d70dca4ea upstream.
After arbitrary bio size was introduced, the incoming bio may
be very big. We have to split the bio into small bios so that
each holds at most BIO_MAX_PAGES bvecs for safety reason, such
as bio_clone().
This patch fixes the following kernel crash:
> [ 172.660142] BUG: unable to handle kernel NULL pointer dereference at 0000000000000028
> [ 172.660229] IP: [<ffffffff811e53b4>] bio_trim+0xf/0x2a
> [ 172.660289] PGD 7faf3e067 PUD 7f9279067 PMD 0
> [ 172.660399] Oops: 0000 [#1] SMP
> [...]
> [ 172.664780] Call Trace:
> [ 172.664813] [<ffffffffa007f3be>] ? raid1_make_request+0x2e8/0xad7 [raid1]
> [ 172.664846] [<ffffffff811f07da>] ? blk_queue_split+0x377/0x3d4
> [ 172.664880] [<ffffffffa005fb5f>] ? md_make_request+0xf6/0x1e9 [md_mod]
> [ 172.664912] [<ffffffff811eb860>] ? generic_make_request+0xb5/0x155
> [ 172.664947] [<ffffffffa0445c89>] ? prio_io+0x85/0x95 [bcache]
> [ 172.664981] [<ffffffffa0448252>] ? register_cache_set+0x355/0x8d0 [bcache]
> [ 172.665016] [<ffffffffa04497d3>] ? register_bcache+0x1006/0x1174 [bcache]
The issue can be reproduced by the following steps:
- create one raid1 over two virtio-blk
- build bcache device over the above raid1 and another cache device
and bucket size is set as 2Mbytes
- set cache mode as writeback
- run random write over ext4 on the bcache device
Fixes: 54efd50(block: make generic_make_request handle arbitrarily sized bios)
Reported-by: Sebastian Roesner <sroesner-kernelorg@roesner-online.de>
Reported-by: Eric Wheeler <bcache@lists.ewheeler.net>
Cc: Shaohua Li <shli@fb.com>
Acked-by: Kent Overstreet <kent.overstreet@gmail.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b85608681 upstream.
blk_set_queue_dying() can be called while another thread is
submitting I/O or changing queue flags, e.g. through dm_stop_queue().
Hence protect the QUEUE_FLAG_DYING flag change with locking.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b47820edd1 upstream.
We temporally change checksum fields in buffers of some types of
metadata into '0' for verifying the checksum values. By doing this
without locking the buffer, some metadata's checksums, which are
being committed or written back to the storage, could be damaged.
In our test, several metadata blocks were found with damaged metadata
checksum value during recovery process. When we only verify the
checksum value, we have to avoid modifying checksum fields directly.
Signed-off-by: Daeho Jeong <daeho.jeong@samsung.com>
Signed-off-by: Youngjin Gil <youngjin.gil@samsung.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Cc: Török Edwin <edwin@etorok.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e81a4eeed upstream.
When we need to move xattrs into external xattr block, we call
ext4_xattr_block_set() from ext4_expand_extra_isize_ea(). That may end
up calling ext4_mark_inode_dirty() again which will recurse back into
the inode expansion code leading to deadlocks.
Protect from recursion using EXT4_STATE_NO_EXPAND inode flag and move
its management into ext4_expand_extra_isize_ea() since its manipulation
is safe there (due to xattr_sem) from possible races with
ext4_xattr_set_handle() which plays with it as well.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 443a8c41cd upstream.
We did not count with the padding of xattr value when computing desired
shift of xattrs in the inode when expanding i_extra_isize. As a result
we could create unaligned start of inline xattrs. Account for alignment
properly.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 418c12d08d upstream.
When multiple xattrs need to be moved out of inode, we did not properly
recompute total size of xattr headers in the inode and the new header
position. Thus when moving the second and further xattr we asked
ext4_xattr_shift_entries() to move too much and from the wrong place,
resulting in possible xattr value corruption or general memory
corruption.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0141191a2 upstream.
The code in ext4_expand_extra_isize_ea() treated new_extra_isize
argument sometimes as the desired target i_extra_isize and sometimes as
the amount by which we need to grow current i_extra_isize. These happen
to coincide when i_extra_isize is 0 which used to be the common case and
so nobody noticed this until recently when we added i_projid to the
inode and so i_extra_isize now needs to grow from 28 to 32 bytes.
The result of these bugs was that we sometimes unnecessarily decided to
move xattrs out of inode even if there was enough space and we often
ended up corrupting in-inode xattrs because arguments to
ext4_xattr_shift_entries() were just wrong. This could demonstrate
itself as BUG_ON in ext4_xattr_shift_entries() triggering.
Fix the problem by introducing new isize_diff variable and use it where
appropriate.
Reported-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 829fa70ddd upstream.
A number of fuzzing failures seem to be caused by allocation bitmaps
or other metadata blocks being pointed at the superblock.
This can cause kernel BUG or WARNings once the superblock is
overwritten, so validate the group descriptor blocks to make sure this
doesn't happen.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2d7f9e2ad3 upstream.
Filesystem uids which don't map into a user namespace may result
in inode->i_uid being INVALID_UID. A symlink and its parent
could have different owners in the filesystem can both get
mapped to INVALID_UID, which may result in following a symlink
when this would not have otherwise been permitted when protected
symlinks are enabled.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d6e0d30644 upstream.
The capability check should not be audited since it is only being used
to determine the inode permissions. A failed check does not indicate a
violation of security policy but, when an LSM is enabled, a denial audit
message was being generated.
The denial audit message caused confusion for some application authors
because root-running Go applications always triggered the denial. To
prevent this confusion, the capability check in net_ctl_permissions() is
switched to the noaudit variant.
BugLink: https://launchpad.net/bugs/1465724
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Acked-by: Serge E. Hallyn <serge.hallyn@ubuntu.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 98f368e9e2 upstream.
When checking the current cred for a capability in a specific user
namespace, it isn't always desirable to have the LSMs audit the check.
This patch adds a noaudit variant of ns_capable() for when those
situations arise.
The common logic between ns_capable() and the new ns_capable_noaudit()
is moved into a single, shared function to keep duplicated code to a
minimum and ease maintainability.
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Acked-by: Serge E. Hallyn <serge.hallyn@ubuntu.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit de7c4cc947 upstream.
When finding a child profile via an rcu critical section, the profile
may be put and scheduled for deletion after the child is found but
before its refcount is incremented.
Protect against this by repeating the lookup if the profiles refcount
is 0 and is one its way to deletion.
Signed-off-by: John Johansen <john.johansen@canonical.com>
Acked-by: Seth Arnold <seth.arnold@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bdc54d8e3c upstream.
If there were less than 2 entries in the multipath list, then
xprt_iter_next_entry_multiple() would never advance beyond the
first entry, which is correct for round robin behaviour, but not
for the list iteration.
The end result would be infinite looping in rpc_clnt_iterate_for_each_xprt()
as we would never see the xprt == NULL condition fulfilled.
Reported-by: Oleg Drokin <green@linuxhacker.ru>
Fixes: 80b14d5e61 ("SUNRPC: Add a structure to track multiple transports")
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Cc: Jason L Tibbitts III <tibbs@math.uh.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 17d0774f80 upstream.
Attributes declared with __ATTR_PREALLOC use sysfs_kf_read() which returns
zero bytes for non-zero offset. This breaks script checkarray in mdadm tool
in debian where /bin/sh is 'dash' because its builtin 'read' reads only one
byte at a time. Script gets 'i' instead of 'idle' when reads current action
from /sys/block/$dev/md/sync_action and as a result does nothing.
This patch adds trivial implementation of partial read: generate whole
string and move required part into buffer head.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Fixes: 4ef67a8c95 ("sysfs/kernfs: make read requests on pre-alloc files use the buffer.")
Link: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=787950
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b027d11263 upstream.
The commit 02fc76f6a changed base of the sysfs attributes from device to card.
The "show" callbacks dereferenced wrong objects because of this.
Fixes: 02fc76f6a7 ('ALSA: line6: Create sysfs via snd_card_add_dev_attr()')
Reviewed-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Andrej Krutak <dev@andree.sk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e4379eae0 upstream.
If there's an error, pcm is released in line6_pcm_acquire already.
Fixes: 247d95ee6d ('ALSA: line6: Handle error from line6_pcm_acquire()')
Reviewed-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Andrej Krutak <dev@andree.sk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5331d9cab3 upstream.
Commit e647b53227 ("ACPI: Add early device probing infrastructure")
introduced code that allows inserting driver specific
struct acpi_probe_entry probe entries into ACPI linker sections
(one per-subsystem, eg irqchip, clocksource) that are then walked
to retrieve the data and function hooks required to probe the
respective kernel components.
Probing for all entries in a section is triggered through
the __acpi_probe_device_table() function, that in turn, according
to the table ID a given probe entry reports parses the table
with the function retrieved from the respective section structures
(ie struct acpi_probe_entry). Owing to the current ACPI table
parsing implementation, the __acpi_probe_device_table() function
has to share global variables with the acpi_match_madt() function, so
in order to guarantee mutual exclusion locking is required
between the two functions.
Current kernel code implements the locking through the acpi_probe_lock
spinlock; this has the side effect of requiring all code called
within the lock (ie struct acpi_probe_entry.probe_{table/subtbl} hooks)
not to sleep.
However, kernel subsystems that make use of the early probing
infrastructure are relying on kernel APIs that may sleep (eg
irq_domain_alloc_fwnode(), among others) in the function calls
pointed at by struct acpi_probe_entry.{probe_table/subtbl} entries
(eg gic_v2_acpi_init()), which is a bug.
Since __acpi_probe_device_table() is called from context
that is allowed to sleep the acpi_probe_lock spinlock can be replaced
with a mutex; this fixes the issue whilst still guaranteeing
mutual exclusion.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Fixes: e647b53227 (ACPI: Add early device probing infrastructure)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3feab13c91 upstream.
When the ACPI_DECLARE_PROBE_ENTRY macro was added in
commit e647b53227 ("ACPI: Add early device probing infrastructure"),
a stub macro adding an unused entry was added for the !CONFIG_ACPI
Kconfig option case to make sure kernel code making use of the
macro did not require to be guarded within CONFIG_ACPI in order to
be compiled.
The stub macro was never used since all kernel code that defines
ACPI_DECLARE_PROBE_ENTRY entries is currently guarded within
CONFIG_ACPI; it contains a typo that should be nonetheless fixed.
Fix the typo in the stub (ie !CONFIG_ACPI) ACPI_DECLARE_PROBE_ENTRY()
macro so that it can actually be used if needed.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Fixes: e647b53227 (ACPI: Add early device probing infrastructure)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ca05345c5 upstream.
For counter subdevices, the `s->insn_write` handler is being set to the
wrong function, `ni_tio_insn_read()`. It should be
`ni_tio_insn_write()`.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reported-by: Éric Piel <piel@delmic.com>
Fixes: 10f74377ee ("staging: comedi: ni_tio: make ni_tio_winsn() a
proper comedi (*insn_write)"
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f0f4b0cc3a upstream.
Commit ebb657babf ("staging: comedi: ni_mio_common: clarify the
cmd->start_arg validation and use") introduced a backwards compatibility
issue in the use of asynchronous commands on the AO subdevice when
`start_src` is `TRIG_EXT`. Valid values for `start_src` are `TRIG_INT`
(for internal, software trigger), and `TRIG_EXT` (for external trigger).
When set to `TRIG_EXT`. In both cases, the driver relies on an
internal, software trigger to set things up (allowing the user
application to write sufficient samples to the data buffer before the
trigger), so it acts as a software "pre-trigger" in the `TRIG_EXT` case.
The software trigger is handled by `ni_ao_inttrig()`.
Prior to the above change, when `start_src` was `TRIG_INT`, `start_arg`
was required to be 0, and `ni_ao_inttrig()` checked that the software
trigger number was also 0. After the above change, when `start_src` was
`TRIG_INT`, any value was allowed for `start_arg`, and `ni_ao_inttrig()`
checked that the software trigger number matched this `start_arg` value.
The backwards compatibility issue is that the internal trigger number
now has to match `start_arg` when `start_src` is `TRIG_EXT` when it
previously had to be 0.
Fix the backwards compatibility issue in `ni_ao_inttrig()` by always
allowing software trigger number 0 when `start_src` is something other
than `TRIG_INT`.
Thanks to Spencer Olson for reporting the issue.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reported-by: Spencer Olson <olsonse@umich.edu>
Fixes: ebb657babf ("staging: comedi: ni_mio_common: clarify the cmd->start_arg validation and use")
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 403fe7f34e upstream.
Commit 73e0e4dfed ("staging: comedi: comedi_test: fix timer lock-up")
fixed a lock-up in the timer routine `waveform_ai_timer()` (which was
called `waveform_ai_interrupt()` at the time) caused by
commit 2405124744 ("staging: comedi: comedi_test: use
comedi_handle_events()"). However, it introduced a race condition that
can result in the timer routine misbehaving, such as accessing freed
memory or dereferencing a NULL pointer.
73e0... changed the timer routine to do nothing unless a
`WAVEFORM_AI_RUNNING` flag was set, and changed `waveform_ai_cancel()`
to clear the flag and replace a call to `del_timer_sync()` with a call
to `del_timer()`. `waveform_ai_cancel()` may be called from the timer
routine itself (via `comedi_handle_events()`), or from `do_cancel()`.
(`do_cancel()` is called as a result of a file operation (usually a
`COMEDI_CANCEL` ioctl command, or a release), or during device removal.)
When called from `do_cancel()`, the call to `waveform_ai_cancel()` is
followed by a call to `do_become_nonbusy()`, which frees up stuff for
the current asynchronous command under the assumption that it is now
safe to do so. The race condition occurs when the timer routine
`waveform_ai_timer()` checks the `WAVEFORM_AI_RUNNING` flag just before
it is cleared by `waveform_ai_cancel()`, and is still running during the
call to `do_become_nonbusy()`. In particular, it can lead to a NULL
pointer dereference:
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffffc0c63add>] waveform_ai_timer+0x17d/0x290 [comedi_test]
That corresponds to this line in `waveform_ai_timer()`:
unsigned int chanspec = cmd->chanlist[async->cur_chan];
but `do_become_nonbusy()` frees `cmd->chanlist` and sets it to `NULL`.
Fix the race by calling `del_timer_sync()` instead of `del_timer()` in
`waveform_ai_cancel()` when not in an interrupt context. The only time
`waveform_ai_cancel()` is called in an interrupt context is when it is
called from the timer routine itself, via `comedi_handle_events()`.
There is no longer any need for the `WAVEFORM_AI_RUNNING` flag, so get
rid of it.
The bug was copied from the AI subdevice to the AO when support for
commands on the AO subdevice was added by commit 0cf55bbef2 ("staging:
comedi: comedi_test: implement commands on AO subdevice"). That
involves the timer routine `waveform_ao_timer()`, the comedi "cancel"
routine `waveform_ao_cancel()`, and the flag `WAVEFORM_AO_RUNNING`. Fix
it in the same way as for the AI subdevice.
Fixes: 73e0e4dfed ("staging: comedi: comedi_test: fix timer lock-up")
Fixes: 0cf55bbef2 ("staging: comedi: comedi_test: implement commands
on AO subdevice")
Reported-by: Éric Piel <piel@delmic.com>
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: Éric Piel <piel@delmic.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 80e162ee9b upstream.
`daqboard2000_find_boardinfo()` is supposed to check if the
DaqBoard/2000 series model is supported, based on the PCI subvendor and
subdevice ID. The current code is wrong as it is comparing the PCI
device's subdevice ID to an expected, fixed value for the subvendor ID.
It should be comparing the PCI device's subvendor ID to this fixed
value. Correct it.
Fixes: 7e8401b23e ("staging: comedi: daqboard2000: add back subsystem_device check")
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 99f1c01319 upstream.
Right now, if it's an open of a negative dentry, a race is possible
with several openers who all try to instantiate/rehash the same
dentry and would hit a BUG_ON in d_add.
But in fact if we got a negative dentry in atomic_open, that means
we just revalidated it so no point in talking to MDS at all,
just return ENOENT and make the race go away completely.
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3b7c7e52ef upstream.
There is an allocation with GFP_KERNEL flag in mos7840_write(),
while it may be called from interrupt context.
Follow-up for commit 1912528376 ("USB: kobil_sct: fix non-atomic
allocation in write path")
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5a5a1d6142 upstream.
There is an allocation with GFP_KERNEL flag in mos7720_write(),
while it may be called from interrupt context.
Follow-up for commit 1912528376 ("USB: kobil_sct: fix non-atomic
allocation in write path")
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c73358c83 upstream.
The maximum value allowed for wMaxPacketSize of a high-speed interrupt
endpoint is 1024 bytes, not 1023.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: aed9d65ac3 ("USB: validate wMaxPacketValue entries in endpoint descriptors")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c4e9417498 upstream.
When the controller is configured to be dual role and it's in host mode,
if bind udc and gadgt driver, those gadget operations will do gadget
disconnect and finally pull down DP line, which will break host function.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 53e5f36fbd upstream.
UBSAN complains about a left shift by -1 in proc_do_submiturb(). This
can occur when an URB is submitted for a bulk or control endpoint on
a high-speed device, since the code doesn't bother to check the
endpoint type; normally only interrupt or isochronous endpoints have
a nonzero bInterval value.
Aside from the fact that the operation is illegal, it shouldn't matter
because the result isn't used. Still, in theory it could cause a
hardware exception or other problem, so we should work around it.
This patch avoids doing the left shift unless the shift amount is >= 0.
The same piece of code has another problem. When checking the device
speed (the exponential encoding for interrupt endpoints is used only
by high-speed or faster devices), we need to look for speed >=
USB_SPEED_SUPER as well as speed == USB_SPEED HIGH. The patch adds
this check.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Vittorio Zecca <zeccav@gmail.com>
Tested-by: Vittorio Zecca <zeccav@gmail.com>
Suggested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 626d2f07de upstream.
The USB-DMAC's interruption happens even if the CHCR.DE is not set to 1
because CHCR.NULLE is set to 1. So, this driver should call
usb_dmac_isr_transfer_end() if the DE bit is set to 1 only. Otherwise,
the desc is possible to be NULL in the usb_dmac_isr_transfer_end().
Fixes: 0c1c8ff32f ("dmaengine: usb-dmac: Add Renesas USB DMA Controller (USB-DMAC) driver)
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e514cc0a49 upstream.
The props->ap[] array is defined like this:
struct alg_props ap[NX_MAX_FC][NX_MAX_MODE][3];
So we can see that if msc->fc and msc->mode are == to NX_MAX_FC or
NX_MAX_MODE then we're off by one.
Fixes: ae0222b728 ('powerpc/crypto: nx driver code supporting nx encryption')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 47af45d684 upstream.
The commit 4097461897 ("Input: i8042 - break load dependency ...")
correctly set up ps2_cmd_mutex pointer for the KBD port but forgot to do
the same for AUX port(s), which results in communication on KBD and AUX
ports to clash with each other.
Fixes: 4097461897 ("Input: i8042 - break load dependency ...")
Reported-by: Bruno Wolff III <bruno@wolff.to>
Tested-by: Bruno Wolff III <bruno@wolff.to>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4097461897 upstream.
As explained in 1407814240-4275-1-git-send-email-decui@microsoft.com we
have a hard load dependency between i8042 and atkbd which prevents
keyboard from working on Gen2 Hyper-V VMs.
> hyperv_keyboard invokes serio_interrupt(), which needs a valid serio
> driver like atkbd.c. atkbd.c depends on libps2.c because it invokes
> ps2_command(). libps2.c depends on i8042.c because it invokes
> i8042_check_port_owner(). As a result, hyperv_keyboard actually
> depends on i8042.c.
>
> For a Generation 2 Hyper-V VM (meaning no i8042 device emulated), if a
> Linux VM (like Arch Linux) happens to configure CONFIG_SERIO_I8042=m
> rather than =y, atkbd.ko can't load because i8042.ko can't load(due to
> no i8042 device emulated) and finally hyperv_keyboard can't work and
> the user can't input: https://bugs.archlinux.org/task/39820
> (Ubuntu/RHEL/SUSE aren't affected since they use CONFIG_SERIO_I8042=y)
To break the dependency we move away from using i8042_check_port_owner()
and instead allow serio port owner specify a mutex that clients should use
to serialize PS/2 command stream.
Reported-by: Mark Laws <mdl@60hz.org>
Tested-by: Mark Laws <mdl@60hz.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 35bbb97fc8 upstream.
commit 909c3a22da (Btrfs: fix loading of orphan roots leading to BUG_ON)
avoids the BUG_ON but can add an aliased root to the dead_roots list or
leak the root.
Since we've already been loading roots into the radix tree, we should
use it before looking the root up on disk.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d2c609b834 upstream.
The qgroup_flags field is overloaded such that it reflects the on-disk
status of qgroups and the runtime state. The BTRFS_QGROUP_STATUS_FLAG_RESCAN
flag is used to indicate that a rescan operation is in progress, but if
the file system is unmounted while a rescan is running, the rescan
operation is paused. If the file system is then mounted read-only,
the flag will still be present but the rescan operation will not have
been resumed. When we go to umount, btrfs_qgroup_wait_for_completion
will see the flag and interpret it to mean that the rescan worker is
still running and will wait for a completion that will never come.
This patch uses a separate flag to indicate when the worker is
running. The locking and state surrounding the qgroup rescan worker
needs a lot of attention beyond this patch but this is enough to
avoid a hung umount.
Signed-off-by; Jeff Mahoney <jeffm@suse.com>
Reviewed-by: Qu Wenruo <quwenruo@cn.fujitsu.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Chris Mason <clm@fb.com>
commit d06f23d6a9 upstream.
We wait on qgroup rescan completion in three places: file system
shutdown, the quota disable ioctl, and the rescan wait ioctl. If the
user sends a signal while we're waiting, we continue happily along. This
is expected behavior for the rescan wait ioctl. It's racy in the shutdown
path but mostly works due to other unrelated synchronization points.
In the quota disable path, it Oopses the kernel pretty much immediately.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0e5845561 upstream.
The data offset for a dax region needs to account for a reservation in
the resource range. Otherwise, device-dax is allowing mappings directly
into the memmap or device-info-block area with crash signatures like the
following:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
IP: get_zone_device_page+0x11/0x30
Call Trace:
follow_devmap_pmd+0x298/0x2c0
follow_page_mask+0x275/0x530
__get_user_pages+0xe3/0x750
__gfn_to_pfn_memslot+0x1b2/0x450 [kvm]
tdp_page_fault+0x130/0x280 [kvm]
kvm_mmu_page_fault+0x5f/0xf0 [kvm]
handle_ept_violation+0x94/0x180 [kvm_intel]
vmx_handle_exit+0x1d3/0x1440 [kvm_intel]
kvm_arch_vcpu_ioctl_run+0x81d/0x16a0 [kvm]
kvm_vcpu_ioctl+0x33c/0x620 [kvm]
do_vfs_ioctl+0xa2/0x5d0
SyS_ioctl+0x79/0x90
entry_SYSCALL_64_fastpath+0x1a/0xa4
Fixes: ab68f26221 ("/dev/dax, pmem: direct access to persistent memory")
Link: http://lkml.kernel.org/r/147205536732.1606.8994275381938837346.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reported-by: Abhilash Kumar Mulumudi <m.abhilash-kumar@hpe.com>
Reported-by: Toshi Kani <toshi.kani@hpe.com>
Tested-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 804dd15046 upstream.
While adding proper userfaultfd_wp support with bits in pagetable and
swap entry to avoid false positives WP userfaults through swap/fork/
KSM/etc, I've been adding a framework that mostly mirrors soft dirty.
So I noticed in one place I had to add uffd_wp support to the pagetables
that wasn't covered by soft_dirty and I think it should have.
Example: in the THP migration code migrate_misplaced_transhuge_page()
pmd_mkdirty is called unconditionally after mk_huge_pmd.
entry = mk_huge_pmd(new_page, vma->vm_page_prot);
entry = maybe_pmd_mkwrite(pmd_mkdirty(entry), vma);
That sets soft dirty too (it's a false positive for soft dirty, the soft
dirty bit could be more finegrained and transfer the bit like uffd_wp
will do.. pmd/pte_uffd_wp() enforces the invariant that when it's set
pmd/pte_write is not set).
However in the THP split there's no unconditional pmd_mkdirty after
mk_huge_pmd and pte_swp_mksoft_dirty isn't called after the migration
entry is created. The code sets the dirty bit in the struct page
instead of setting it in the pagetable (which is fully equivalent as far
as the real dirty bit is concerned, as the whole point of pagetable bits
is to be eventually flushed out of to the page, but that is not
equivalent for the soft-dirty bit that gets lost in translation).
This was found by code review only and totally untested as I'm working
to actually replace soft dirty and I don't have time to test potential
soft dirty bugfixes as well :).
Transfer the soft_dirty from pmd to pte during THP splits.
This fix avoids losing the soft_dirty bit and avoids userland memory
corruption in the checkpoint.
Fixes: eef1b3ba05 ("thp: implement split_huge_pmd()")
Link: http://lkml.kernel.org/r/1471610515-30229-2-git-send-email-aarcange@redhat.com
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Acked-by: Pavel Emelyanov <xemul@virtuozzo.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 088bf2ff5d upstream.
seq_read() is a nasty piece of work, not to mention buggy.
It has (I think) an old bug which allows unprivileged userspace to read
beyond the end of m->buf.
I was getting these:
BUG: KASAN: slab-out-of-bounds in seq_read+0xcd2/0x1480 at addr ffff880116889880
Read of size 2713 by task trinity-c2/1329
CPU: 2 PID: 1329 Comm: trinity-c2 Not tainted 4.8.0-rc1+ #96
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.9.3-0-ge2fc41e-prebuilt.qemu-project.org 04/01/2014
Call Trace:
kasan_object_err+0x1c/0x80
kasan_report_error+0x2cb/0x7e0
kasan_report+0x4e/0x80
check_memory_region+0x13e/0x1a0
kasan_check_read+0x11/0x20
seq_read+0xcd2/0x1480
proc_reg_read+0x10b/0x260
do_loop_readv_writev.part.5+0x140/0x2c0
do_readv_writev+0x589/0x860
vfs_readv+0x7b/0xd0
do_readv+0xd8/0x2c0
SyS_readv+0xb/0x10
do_syscall_64+0x1b3/0x4b0
entry_SYSCALL64_slow_path+0x25/0x25
Object at ffff880116889100, in cache kmalloc-4096 size: 4096
Allocated:
PID = 1329
save_stack_trace+0x26/0x80
save_stack+0x46/0xd0
kasan_kmalloc+0xad/0xe0
__kmalloc+0x1aa/0x4a0
seq_buf_alloc+0x35/0x40
seq_read+0x7d8/0x1480
proc_reg_read+0x10b/0x260
do_loop_readv_writev.part.5+0x140/0x2c0
do_readv_writev+0x589/0x860
vfs_readv+0x7b/0xd0
do_readv+0xd8/0x2c0
SyS_readv+0xb/0x10
do_syscall_64+0x1b3/0x4b0
return_from_SYSCALL_64+0x0/0x6a
Freed:
PID = 0
(stack is not available)
Memory state around the buggy address:
ffff88011688a000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffff88011688a080: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>ffff88011688a100: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
^
ffff88011688a180: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff88011688a200: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
==================================================================
Disabling lock debugging due to kernel taint
This seems to be the same thing that Dave Jones was seeing here:
https://lkml.org/lkml/2016/8/12/334
There are multiple issues here:
1) If we enter the function with a non-empty buffer, there is an attempt
to flush it. But it was not clearing m->from after doing so, which
means that if we try to do this flush twice in a row without any call
to traverse() in between, we are going to be reading from the wrong
place -- the splat above, fixed by this patch.
2) If there's a short write to userspace because of page faults, the
buffer may already contain multiple lines (i.e. pos has advanced by
more than 1), but we don't save the progress that was made so the
next call will output what we've already returned previously. Since
that is a much less serious issue (and I have a headache after
staring at seq_read() for the past 8 hours), I'll leave that for now.
Link: http://lkml.kernel.org/r/1471447270-32093-1-git-send-email-vegard.nossum@oracle.com
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2527ecc919 upstream.
The UserMode (UM) Linux build was failing in gpiolib-of as it requires
ioremap()/iounmap() to exist, which is absent from UM. The non-existence
of IO memory is negatively defined as CONFIG_NO_IOMEM which means we
need to depend on HAS_IOMEM.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3295235fd7 upstream.
In case of error, the function usb_get_phy() returns ERR_PTR() and never
returns NULL. The NULL test in the return value check should be replaced
with IS_ERR().
Fixes: b5a2875605 ("usb: renesas_usbhs: Allow an OTG PHY driver to
provide VBUS")
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7f851684e upstream.
Found one megaraid_sas HBA probe fails,
[ 187.235190] scsi host2: Avago SAS based MegaRAID driver
[ 191.112365] megaraid_sas 0000:89:00.0: BAR 0: can't reserve [io 0x0000-0x00ff]
[ 191.120548] megaraid_sas 0000:89:00.0: IO memory region busy!
and the card has resource like,
[ 125.097714] pci 0000:89:00.0: [1000:005d] type 00 class 0x010400
[ 125.104446] pci 0000:89:00.0: reg 0x10: [io 0x0000-0x00ff]
[ 125.110686] pci 0000:89:00.0: reg 0x14: [mem 0xce400000-0xce40ffff 64bit]
[ 125.118286] pci 0000:89:00.0: reg 0x1c: [mem 0xce300000-0xce3fffff 64bit]
[ 125.125891] pci 0000:89:00.0: reg 0x30: [mem 0xce200000-0xce2fffff pref]
that does not io port resource allocated from BIOS, and kernel can not
assign one as io port shortage.
The driver is only looking for MEM, and should not fail.
It turns out megasas_init_fw() etc are using bar index as mask. index 1
is used as mask 1, so that pci_request_selected_regions() is trying to
request BAR0 instead of BAR1.
Fix all related reference.
Fixes: b6d5d8808b ("megaraid_sas: Use lowest memory bar for SR-IOV VF support")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4d01d88019 upstream.
cros_ec_cmd_xfer returns success status if the command transport
completes successfully, but the execution result is incorrectly ignored.
In many cases, the execution result is assumed to be successful, leading
to ignored errors and operating on uninitialized data.
We've recently introduced the cros_ec_cmd_xfer_status() helper to avoid these
problems. Let's use it.
[Regarding the 'Fixes' tag; there is significant refactoring since the driver's
introduction, but the underlying logical error exists throughout I believe]
Fixes: 9d230c9e4f ("i2c: ChromeOS EC tunnel driver")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fa00c437ee upstream.
In aacraid's ioctl_send_fib() we do two fetches from userspace, one the
get the fib header's size and one for the fib itself. Later we use the
size field from the second fetch to further process the fib. If for some
reason the size from the second fetch is different than from the first
fix, we may encounter an out-of- bounds access in aac_fib_send(). We
also check the sender size to insure it is not out of bounds. This was
reported in https://bugzilla.kernel.org/show_bug.cgi?id=116751 and was
assigned CVE-2016-6480.
Reported-by: Pengfei Wang <wpengfeinudt@gmail.com>
Fixes: 7c00ffa31 '[SCSI] 2.6 aacraid: Variable FIB size (updated patch)'
Signed-off-by: Dave Carroll <david.carroll@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45c3b08a11 upstream.
For resources shared by all cores such as SLC and IOC, only the master
core needs to do any setups / enabling / disabling etc.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 18b43e89d2 upstream.
trace_hardirqs_on_caller() in lockdep.c expects to be called before, not
after interrupts are actually enabled.
The following comment in kernel/locking/lockdep.c substantiates this
claim:
"
/*
* We're enabling irqs and according to our state above irqs weren't
* already enabled, yet we find the hardware thinks they are in fact
* enabled.. someone messed up their IRQ state tracing.
*/
"
An example can be found in include/linux/irqflags.h:
do { trace_hardirqs_on(); raw_local_irq_enable(); } while (0)
Without this change, we hit the following DEBUG_LOCKS_WARN_ON.
[ 7.760000] ------------[ cut here ]------------
[ 7.760000] WARNING: CPU: 0 PID: 1 at kernel/locking/lockdep.c:2711 resume_user_mode_begin+0x48/0xf0
[ 7.770000] DEBUG_LOCKS_WARN_ON(!irqs_disabled())
[ 7.780000] Modules linked in:
[ 7.780000] CPU: 0 PID: 1 Comm: init Not tainted 4.7.0-00003-gc668bb9-dirty #366
[ 7.790000]
[ 7.790000] Stack Trace:
[ 7.790000] arc_unwind_core.constprop.1+0xa4/0x118
[ 7.800000] warn_slowpath_fmt+0x72/0x158
[ 7.800000] resume_user_mode_begin+0x48/0xf0
[ 7.810000] ---[ end trace 6f6a7a8fae20d2f0 ]---
Signed-off-by: Daniel Mentz <danielmentz@google.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c3c909303 upstream.
| CC mm/memory.o
| In file included from ../mm/memory.c:53:0:
| ../include/linux/pfn_t.h: In function ‘pfn_t_pte’:
| ../include/linux/pfn_t.h:78:2: error: conversion to non-scalar type requested
| return pfn_pte(pfn_t_to_pfn(pfn), pgprot);
With STRICT_MM_TYPECHECKS pte_t is a struct and the offending code
forces a cast which ends up shifting a struct and hence the gcc warning.
Note that in recent past some of the arches (aarch64, s390) made
STRICT_MM_TYPECHECKS default, but we don't for ARC as this leads to slightly
worse generated code, given ARC ABI definition of returning structs
(which pte_t would become)
Quoting from ARC ABI...
"Results of type struct are returned in a caller-supplied temporary
variable whose address is passed in r0.
For such functions, the arguments are shifted so that they are
passed in r1 and up."
So
- struct to be returned would be allocated on stack requiring extra
code at call sites
- callee updates stack memory to facilitate the return (vs. simple
MOV into return reg r0)
Hence STRICT_MM_TYPECHECKS is not enabled by default for ARC
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 86147e3cfa upstream.
User mode callee regs are explicitly collected before signal delivery or
breakpoint trap. r25 is special for kernel as it serves as task pointer,
so user mode value is clobbered very early. It is saved in pt_regs where
generally only scratch (aka caller saved) regs are saved.
The code to access the corresponding pt_regs location had a subtle bug as
it was using load/store with scaling of offset, whereas the offset was already
byte wise correct. So fix this by replacing LD.AS with a standard LD
Signed-off-by: Liav Rehana <liavr@mellanox.com>
Reviewed-by: Alexey Brodkin <abrodkin@synopsys.com>
[vgupta: rewrote title and commit log]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 84c8e0963d upstream.
Unfortunately, there's two situations where we lose hpd right now:
- Runtime suspend
- When we've shut off all of the power wells on Valleyview/Cherryview
While it would be nice if this didn't cause issues, this has the
ability to get us in some awkward states where a user won't be able to
get their display to turn on. For instance; if we boot a Valleyview
system without any monitors connected, it won't need any of it's power
wells and thus shut them off. Since this causes us to lose HPD, this
means that unless the user knows how to ssh into their machine and do a
manual reprobe for monitors, none of the monitors they connect after
booting will actually work.
Eventually we should come up with a better fix then having to enable
polling for this, since this makes rpm a lot less useful, but for now
the infrastructure in i915 just isn't there yet to get hpd in these
situations.
Changes since v1:
- Add comment explaining the addition of the if
(!mode_config->poll_running) in intel_hpd_init()
- Remove unneeded if (!dev->mode_config.poll_enabled) in
i915_hpd_poll_init_work()
- Call to drm_helper_hpd_irq_event() after we disable polling
- Add cancel_work_sync() call to intel_hpd_cancel_work()
Changes since v2:
- Apparently dev->mode_config.poll_running doesn't actually reflect
whether or not a poll is currently in progress, and is actually used
for dynamic module paramter enabling/disabling. So now we instead
keep track of our own poll_running variable in dev_priv->hotplug
- Clean i915_hpd_poll_init_work() a little bit
Changes since v3:
- Remove the now-redundant connector loop in intel_hpd_init(), just
rely on intel_hpd_poll_enable() for setting connector->polled
correctly on each connector
- Get rid of poll_running
- Don't assign enabled in i915_hpd_poll_init_work before we actually
lock dev->mode_config.mutex
- Wrap enabled assignment in i915_hpd_poll_init_work() in READ_ONCE()
for doc purposes
- Do the same for dev_priv->hotplug.poll_enabled with WRITE_ONCE in
intel_hpd_poll_enable()
- Add some comments about racing not mattering in intel_hpd_poll_enable
Changes since v4:
- Rename intel_hpd_poll_enable() to intel_hpd_poll_init()
- Drop the bool argument from intel_hpd_poll_init()
- Remove redundant calls to intel_hpd_poll_init()
- Rename poll_enable_work to poll_init_work
- Add some kerneldoc for intel_hpd_poll_init()
- Cross-reference intel_hpd_poll_init() in intel_hpd_init()
- Just copy the loop from intel_hpd_init() in intel_hpd_poll_init()
Changes since v5:
- Minor kerneldoc nitpicks
Cc: stable@vger.kernel.org
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Lyude <cpaul@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 19625e85c6)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 21842ea84f upstream.
One of the things preventing us from using polling is the fact that
calling valleyview_crt_detect_hotplug() when there's a VGA cable
connected results in sending another hotplug. With polling enabled when
HPD is disabled, this results in a scenario like this:
- We enable power wells and reset the ADPA
- output_poll_exec does force probe on VGA, triggering a hpd
- HPD handler waits for poll to unlock dev->mode_config.mutex
- output_poll_exec shuts off the ADPA, unlocks dev->mode_config.mutex
- HPD handler runs, resets ADPA and brings us back to the start
This results in an endless irq storm getting sent from the ADPA
whenever a VGA connector gets detected in the middle of polling.
Somewhat based off of the "drm/i915: Disable CRT HPD around force
trigger" patch Ville Syrjälä sent a while back
Cc: stable@vger.kernel.org
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Lyude <cpaul@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit b236d7c842)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c732e6ee9 upstream.
While VGA hotplugging worked(ish) before, it looks like that was mainly
because we'd unintentionally enable it in
valleyview_crt_detect_hotplug() when we did a force trigger. This
doesn't work reliably enough because whenever the display powerwell on
vlv gets disabled, the values set in VLV_ADPA get cleared and
consequently VGA hotplugging gets disabled. This causes bugs such as one
we found on an Intel NUC, where doing the following sequence of
hotplugs:
- Disconnect all monitors
- Connect VGA
- Disconnect VGA
- Connect HDMI
Would result in VGA hotplugging becoming disabled, due to the powerwells
getting toggled in the process of connecting HDMI.
Changes since v3:
- Expose intel_crt_reset() through intel_drv.h and call that in
vlv_display_power_well_init() instead of
encoder->base.funcs->reset(&encoder->base);
Changes since v2:
- Use intel_encoder structs instead of drm_encoder structs
Changes since v1:
- Instead of handling the register writes ourself, we just reuse
intel_crt_detect()
- Instead of resetting the ADPA during display IRQ installation, we now
reset them in vlv_display_power_well_init()
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Lyude <cpaul@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Rebase over dev_priv/drm_device embedding.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 9504a89247)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fcf68f3c0b upstream.
When using CONFIG_DEBUG_ATOMIC_SLEEP, the scheduler nicely points out
that we're calling sleeping primitives within the wait_event loop, which
means we might clobber the task state:
[ 10.831289] do not call blocking ops when !TASK_RUNNING; state=1 set at [<ffffffc00026b610>]
[ 10.845531] ------------[ cut here ]------------
[ 10.850161] WARNING: at kernel/sched/core.c:7630
...
[ 12.164333] ---[ end trace 45409966a9a76438 ]---
[ 12.168942] Call trace:
[ 12.171391] [<ffffffc00024ed44>] __might_sleep+0x64/0x90
[ 12.176699] [<ffffffc000954774>] mutex_lock_nested+0x50/0x3fc
[ 12.182440] [<ffffffc0007b9424>] iio_kfifo_buf_data_available+0x28/0x4c
[ 12.189043] [<ffffffc0007b76ac>] iio_buffer_ready+0x60/0xe0
[ 12.194608] [<ffffffc0007b7834>] iio_buffer_read_first_n_outer+0x108/0x1a8
[ 12.201474] [<ffffffc000370d48>] __vfs_read+0x58/0x114
[ 12.206606] [<ffffffc000371740>] vfs_read+0x94/0x118
[ 12.211564] [<ffffffc0003720f8>] SyS_read+0x64/0xb4
[ 12.216436] [<ffffffc000203cb4>] el0_svc_naked+0x24/0x28
To avoid this, we should (a la https://lwn.net/Articles/628628/) use the
wait_woken() function, which avoids the nested sleeping while still
handling races between waiting / wake-events.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 173be9a14f upstream.
Mike reports:
Roughly 10% of the time, ltp testcase getrusage04 fails:
getrusage04 0 TINFO : Expected timers granularity is 4000 us
getrusage04 0 TINFO : Using 1 as multiply factor for max [us]time increment (1000+4000us)!
getrusage04 0 TINFO : utime: 0us; stime: 179us
getrusage04 0 TINFO : utime: 3751us; stime: 0us
getrusage04 1 TFAIL : getrusage04.c:133: stime increased > 5000us:
And tracked it down to the case where the task simply doesn't get
_any_ [us]time ticks.
Update the code to assume all rtime is utime when we lack information,
thus ensuring a task that elides the tick gets time accounted.
Reported-by: Mike Galbraith <umgwanakikbuti@gmail.com>
Tested-by: Mike Galbraith <umgwanakikbuti@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Fredrik Markstrom <fredrik.markstrom@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Radim <rkrcmar@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: Wanpeng Li <wanpeng.li@hotmail.com>
Fixes: 9d7fb04276 ("sched/cputime: Guarantee stime + utime == rtime")
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 34276bb062 upstream.
The called of_graph_get_next_endpoint() already decrements the refcount
of the prev node, so it is wrong to do it again in the calling function.
Use the for_each_endpoint_of_node() helper to interate through the
endpoint OF nodes, which already does the right thing and simplifies
the code a bit.
Fixes: 8ccd0d0ca0
(of: add helper for getting endpoint node of specific identifiers)
Reported-by: David Jander <david@protonic.nl>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 744c6c37cc upstream.
Changes to make the resume from cpu_suspend() code behave more like
secondary boot caused debug exceptions to be unmasked early by
__cpu_setup(). We then go on to restore mdscr_el1 in cpu_do_resume(),
potentially taking break or watch points based on uninitialised registers.
Mask debug exceptions in cpu_do_resume(), which is specific to resume
from cpu_suspend(). Debug exceptions will be restored to their original
state by local_dbg_restore() in cpu_suspend(), which runs after
hw_breakpoint_restore() has re-initialised the other registers.
Reported-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Fixes: cabe1c81ea ("arm64: Change cpu_resume() to enable mmu early then access sleep_sp by va")
Signed-off-by: James Morse <james.morse@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fd363bd417 upstream.
When CONFIG_RANDOMIZE_BASE is selected, we modify the page tables to remap the
kernel at a newly-chosen VA range. We do this with the MMU disabled, but do not
invalidate TLBs prior to re-enabling the MMU with the new tables. Thus the old
mappings entries may still live in TLBs, and we risk violating
Break-Before-Make requirements, leading to TLB conflicts and/or other issues.
We invalidate TLBs when we uninsall the idmap in early setup code, but prior to
this we are subject to issues relating to the Break-Before-Make violation.
Avoid these issues by invalidating the TLBs before the new mappings can be
used by the hardware.
Fixes: f80fb3a3d5 ("arm64: add support for kernel ASLR")
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bc9f3d7788 upstream.
Literal loads of virtual addresses are subject to runtime relocation when
CONFIG_RELOCATABLE=y, and given that the relocation routines run with the
MMU and caches enabled, literal loads of relocated values performed with
the MMU off are not guaranteed to return the latest value unless the
memory covering the literal is cleaned to the PoC explicitly.
So defer the literal load until after the MMU has been enabled, just like
we do for primary_switch() and secondary_switch() in head.S.
Fixes: 1e48ef7fcc ("arm64: add support for building vmlinux as a relocatable PIE binary")
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b07d9ca9b upstream.
The code currently assumes that buffered multicast PS frames don't have
a pending ACK frame for tx status reporting.
However, hostapd sends a broadcast deauth frame on teardown for which tx
status is requested. This can lead to the "Have pending ack frames"
warning on module reload.
Fix this by using ieee80211_free_txskb/ieee80211_purge_tx_queue.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9ba333dc55 upstream.
When a device is in a status where CIO has killed all I/O by itself the
interrupt for a clear request may not contain an irb to determine the
clear function. Instead it contains an error pointer -EIO.
This was ignored by the DASD int_handler leading to a hanging device
waiting for a clear interrupt.
Handle -EIO error pointer correctly for requests that are clear pending and
treat the clear as successful.
Signed-off-by: Stefan Haberland <sth@linux.vnet.ibm.com>
Reviewed-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c5b48fa7e2 upstream.
On Intel Xeon Phi Knights Landing processor family the channels of the
memory controller have untypical arrangement - MC0 is mapped to CH3,4,5
and MC1 is mapped to CH0,1,2. This causes the EDAC driver to report the
channel name incorrectly.
We missed this change earlier, so the code already contains similar
comment, but the translation function is incorrect.
Without this patch:
errors in DIMM_A and DIMM_D were reported in DIMM_D
errors in DIMM_B and DIMM_E were reported in DIMM_E
errors in DIMM_C and DIMM_F were reported in DIMM_F
Correct this.
Hubert Chrzaniuk:
- rebased to 4.8
- comments and code cleanup
Fixes: d0cdf90031 ("sb_edac: Add Knights Landing (Xeon Phi gen 2) support")
Reviewed-by: Tony Luck <tony.luck@intel.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Hubert Chrzaniuk <hubert.chrzaniuk@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: lukasz.anaczkowski@intel.com
Cc: lukasz.odzioba@intel.com
Cc: mchehab@kernel.org
Link: http://lkml.kernel.org/r/1469231089-22837-1-git-send-email-lukasz.odzioba@intel.com
Signed-off-by: Lukasz Odzioba <lukasz.odzioba@intel.com>
[ Boris: Simplify a bit by removing char mc. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce8cb803d8 upstream.
We also need to revert the dynamic OF change, so we get a consistent
state again. Otherwise, we might have two devices enabled e.g. after
pinctrl setup fails.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8cf4345575 upstream.
In the function amd_gpio_irq_enable() and
amd_gpio_direction_input(), remove the code which is setting
the default de-bounce time to 2.75ms.
The driver code shall use the same settings as specified in
BIOS. Any default assignment impacts TouchPad behaviour when
the LevelTrig is set to EDGE FALLING.
Reviewed-by: Ken Xue <Ken.Xue@amd.com>
Signed-off-by: Nitesh Kumar Agrawal <Nitesh-kumar.Agrawal@amd.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b236d0fde upstream.
It's not necessary to unregister pin controller device registered
with devm_pinctrl_register() and using pinctrl_unregister() leads
to a double free.
This is detected by Coccinelle semantic patch.
Fixes: e649f7ec8c ("pinctrl: meson: Use devm_pinctrl_register() for pinctrl registration")
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5bc0a11664 upstream.
The disable_bypass cmdline option changes the SMMUv3 driver to put down
faulting stream table entries by default, as opposed to bypassing
transactions from unconfigured devices.
In this mode of operation, it is entirely expected to see aborting
entries in the stream table if and when we come to installing a valid
translation, so don't trigger a BUG() as a result of misdiagnosing these
entries as stream table corruption.
Fixes: 48ec83bcbc ("iommu/arm-smmu: Add initial driver support for ARM SMMUv3 devices")
Tested-by: Robin Murphy <robin.murphy@arm.com>
Reported-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3714ce1d66 upstream.
Enabling stalling faults can result in hardware deadlock on poorly
designed systems, particularly those with a PCI root complex upstream of
the SMMU.
Although it's not really Linux's job to save hardware integrators from
their own misfortune, it *is* our job to stop userspace (e.g. VFIO
clients) from hosing the system for everybody else, even if they might
already be required to have elevated privileges.
Given that the fault handling code currently executes entirely in IRQ
context, there is nothing that can sensibly be done to recover from
things like page faults anyway, so let's rip this code out for now and
avoid the potential for deadlock.
Fixes: 48ec83bcbc ("iommu/arm-smmu: Add initial driver support for ARM SMMUv3 devices")
Reported-by: Matt Evans <matt.evans@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aea2037e0d upstream.
In the unlikely event of a global command queue error, the ARM SMMUv3
driver attempts to convert the problematic command into a CMD_SYNC and
resume the command queue. Unfortunately, this code is pretty badly
broken:
1. It uses the index into the error string table as the CMDQ index,
so we probably read the wrong entry out of the queue
2. The arguments to queue_write are the wrong way round, so we end up
writing from the queue onto the stack.
These happily cancel out, so the kernel is likely to stay alive, but
the command queue will probably fault again when we resume.
This patch fixes the error handling code to use the correct queue index
and write back the CMD_SYNC to the faulting entry.
Fixes: 48ec83bcbc ("iommu/arm-smmu: Add initial driver support for ARM SMMUv3 devices")
Reported-by: Diwakar Subraveti <Diwakar.Subraveti@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e633fc7a13 upstream.
Due to the attribute bits being all over the place in the different
types of short-descriptor PTEs, when remapping an existing entry, e.g.
splitting a section into pages, we take the approach of decomposing
the PTE attributes back to the IOMMU API flags to start from scratch.
On inspection, though, the existing code seems to have got the read-only
bit backwards and ignored the XN bit. How embarrassing...
Fortunately the primary user so far, the Mediatek IOMMU, both never
splits blocks (because it only serves non-overlapping DMA API calls) and
also ignores permissions anyway, but let's put things right before any
future users trip up.
Fixes: e5fc9753b1 ("iommu/io-pgtable: Add ARMv7 short descriptor support")
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ec60043f7 upstream.
Due to the limitations of having to wait until we see a device's DMA
restrictions before we know how we want an IOVA domain initialised,
there is a window for error if a DMA ops domain is allocated but later
freed without ever being used. In that case, init_iova_domain() was
never called, so calling put_iova_domain() from iommu_put_dma_cookie()
ends up trying to take an uninitialised lock and crashing.
Make things robust by skipping the call unless the IOVA domain actually
has been initialised, as we probably should have done from the start.
Fixes: 0db2e5d18f ("iommu: Implement common IOMMU ops for DMA mapping")
Reported-by: Nate Watterson <nwatters@codeaurora.org>
Reviewed-by: Nate Watterson <nwatters@codeaurora.org>
Tested-by: Nate Watterson <nwatters@codeaurora.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 33da54fa86 upstream.
Michael reported 'perf mem -t store record' being broken. The reason is
latest rework of this area:
commit acbe613e0c ("perf tools: Add monitored events array")
We don't mark perf_mem_events store record when -t store option is
specified.
Committer notes:
Before:
# perf mem -t store record usleep 1
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.020 MB perf.data (7 samples) ]
# perf evlist
cycles:ppp
#
After:
# perf mem -t store record usleep 1
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.020 MB perf.data (7 samples) ]
# perf evlist
cpu/mem-stores/P
#
Reported-by: Michael Petlan <mpetlan@redhat.com>
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Fixes: acbe613e0c ("perf tools: Add monitored events array")
Link: http://lkml.kernel.org/r/1470905457-18311-1-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 50de1a0c54 upstream.
Commit 73cdf0c6ea ("perf symbols: Record text offset in dso
to calculate objdump address") started storing the offset of
the text section for all DSOs:
if (elf_section_by_name(elf, &ehdr, &tshdr, ".text", NULL))
dso->text_offset = tshdr.sh_addr - tshdr.sh_offset;
Unfortunately this breaks debuginfo files, because we need to calculate
the offset of the text section in the associated executable file. As a
result perf annotate returns junk for all debuginfo files.
Fix this by using runtime_ss->elf which should point at the executable
when parsing a debuginfo file.
Signed-off-by: Anton Blanchard <anton@samba.org>
Reviewed-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Tested-by: Wang Nan <wangnan0@huawei.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Fixes: 73cdf0c6ea ("perf symbols: Record text offset in dso to calculate objdump address")
Link: http://lkml.kernel.org/r/20160813115533.6de17912@kryten
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6977495c06 upstream.
Ivium Technologies uses the FTDI VID with custom PIDs for their line of
electrochemical interfaces and the PalmSens they developed for PalmSens
BV.
Signed-off-by: Robert Delien <robert@delien.nl>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ae34d12cc1 upstream.
BCM20706V2_EVAL is a WICED dev board designed with FT2232H USB 2.0
UART/FIFO IC.
To support BCM920706V2_EVAL dev board for WICED development on Linux.
Add the VID(0a5c) and PID(6422) to ftdi_sio driver to allow loading
ftdi_sio for this board.
Signed-off-by: Sheng-Hui J. Chu <s.jeffrey.chu@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cf1b18030d upstream.
The device has four interfaces; the three serial ports ought to be
handled by this driver:
00 Diagnostic interface serial port
01 NMEA device serial port
02 Mass storage (sd card)
03 Modem serial port
The other product ids listed in the Windows driver are present already.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 647024a7df upstream.
udriver struct allocated by kzalloc() will not be freed
if usb_register() and next calls fail. This patch fixes this
by adding one more step with kfree(udriver) in error path.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f1f6d9a8b5 upstream.
Remove the hcd after checking for the xhci last quirks, not before.
This caused a hang on a Alpine Ridge xhci based maching which remove
the whole xhci controller when unplugging the last usb device
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 88716a9376 upstream.
After a device is disconnected, xhci_stop_device() will be invoked
in xhci_bus_suspend().
Also the "disconnect" IRQ will have ISR to invoke
xhci_free_virt_device() in this sequence.
xhci_irq -> xhci_handle_event -> handle_cmd_completion ->
xhci_handle_cmd_disable_slot -> xhci_free_virt_device
If xhci->devs[slot_id] has been assigned to NULL in
xhci_free_virt_device(), then virt_dev->eps[i].ring in
xhci_stop_device() may point to an invlid address to cause kernel
panic.
virt_dev = xhci->devs[slot_id];
:
if (virt_dev->eps[i].ring && virt_dev->eps[i].ring->dequeue)
[] Unable to handle kernel paging request at virtual address 00001a68
[] pgd=ffffffc001430000
[] [00001a68] *pgd=000000013c807003, *pud=000000013c807003,
*pmd=000000013c808003, *pte=0000000000000000
[] Internal error: Oops: 96000006 [#1] PREEMPT SMP
[] CPU: 0 PID: 39 Comm: kworker/0:1 Tainted: G U
[] Workqueue: pm pm_runtime_work
[] task: ffffffc0bc0e0bc0 ti: ffffffc0bc0ec000 task.ti:
ffffffc0bc0ec000
[] PC is at xhci_stop_device.constprop.11+0xb4/0x1a4
This issue is found when running with realtek ethernet device
(0bda:8153).
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 33be126510 upstream.
Fix "Command completion event does not match command" errors by always
handling the command ring stopped events.
The command ring stopped event is generated as a result of aborting
or stopping the command ring with a register write. It is not caused
by a command in the command queue, and thus won't have a matching command
in the comman list.
Solve it by handling the command ring stopped event before checking for a
matching command.
In most command time out cases we abort the command ring, and get
a command ring stopped event. The events command pointer will point at
the current command ring dequeue, which in most cases matches the timed
out command in the command list, and no error messages are seen.
If we instead get a command aborted event before the command ring stopped
event, the abort event will increse the command ring dequeue pointer, and
the following command ring stopped events command pointer will point at the
next, not yet queued command. This case triggered the error message
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aed9d65ac3 upstream.
Erroneous or malicious endpoint descriptors may have non-zero bits in
reserved positions, or out-of-bounds values. This patch helps prevent
these from causing problems by bounds-checking the wMaxPacketValue
entries in endpoint descriptors and capping the values at the maximum
allowed.
This issue was first discovered and tests were conducted by Jake Lamberson
<jake.lamberson1@gmail.com>, an intern working for Rosie Hall.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: roswest <roswest@cisco.com>
Tested-by: roswest <roswest@cisco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e0cb1b8416 upstream.
According to the datasheet, SDn clocks are from the SDSRC clock. And
the SDSRC has a 1/2 divider. So, we should have ".sdsrc" as an internal
core clock. Otherwise, since the sdhi driver will calculate clock for
a sd card using the wrong parent clock rate, and then performance will
be not good.
Fixes: 90c073e539 ("clk: shmobile: r8a7795: Add SD divider support")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 700aa7ff8d upstream.
This patch fixes an issue that isochronous transfer's data is possible to
be lost as a workaround. Since this driver uses a workqueue to start
the dmac, the transfer is possible to be delayed when system load is high.
Fixes: 6e4b74e469 ("usb: renesas: fix scheduling in atomic context bug")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9ab967e6db upstream.
This patch fixes an issue that unexpected BRDY interruption happens
when the usb_ep_{enable,disable}() are called with different direction.
In this case, the driver will cause the following message:
renesas_usbhs e6590000.usb: irq_ready run_error 1 : -16
This issue causes the followings:
1) A pipe is enabled as transmission
2) The pipe sent a data
3) The pipe is disabled and re-enabled as reception.
4) The pipe got a queue
Since the driver doesn't clear the BRDYSTS flags after 2) above, the issue
happens. If we add such clearing the flags into the driver, the code will
become complicate. So, this patch clears the BRDYSTS flag of reception in
usbhsg_ep_enable() to avoid complicate.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 772ce81264 upstream.
Since R-Car Gen3 SoC has the USB-DMAC, this driver should set
dparam->has_usb_dmac to 1. Otherwise, behavior of this driver and
the usb-dmac driver will be mismatch, then sometimes receiving data will
be corrupt.
Fixes: de18757e27 ("usb: renesas_usbhs: add R-Car Gen3 power control")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07d316a22e upstream.
The locking in hub_activate() is not adequate to provide full mutual
exclusion with hub_quiesce(). The subroutine locks the hub's
usb_interface, but the callers of hub_quiesce() (such as
hub_pre_reset() and hub_event()) hold the lock to the hub's
usb_device.
This patch changes hub_activate() to make it acquire the same lock as
those other routines.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca5cbc8b02 upstream.
The early-exit pathway in hub_activate, added by commit e50293ef97
("USB: fix invalid memory access in hub_activate()") needs
improvement. It duplicates code that is already present at the end of
the subroutine, and it neglects to undo the effect of a
usb_autopm_get_interface_no_resume() call.
This patch fixes both problems by making the early-exit pathway jump
directly to the end of the subroutine. It simplifies the code at the
end by merging two conditionals that actually test the same condition
although they appear different: If type < HUB_INIT3 then type must be
either HUB_INIT2 or HUB_INIT, and it can't be HUB_INIT because in that
case the subroutine would have exited earlier.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6bb47e8ab9 upstream.
Memory leak and unbalanced reference count:
If the hub gets disconnected while the core is still activating it, this
can result in leaking memory of few USB structures.
This will happen if we have done a kref_get() from hub_activate() and
scheduled a delayed work item for HUB_INIT2/3. Now if hub_disconnect()
gets called before the delayed work expires, then we will cancel the
work from hub_quiesce(), but wouldn't do a kref_put(). And so the
unbalance.
kmemleak reports this as (with the commit e50293ef97 backported to
3.10 kernel with other changes, though the same is true for mainline as
well):
unreferenced object 0xffffffc08af5b800 (size 1024):
comm "khubd", pid 73, jiffies 4295051211 (age 6482.350s)
hex dump (first 32 bytes):
30 68 f3 8c c0 ff ff ff 00 a0 b2 2e c0 ff ff ff 0h..............
01 00 00 00 00 00 00 00 00 94 7d 40 c0 ff ff ff ..........}@....
backtrace:
[<ffffffc0003079ec>] create_object+0x148/0x2a0
[<ffffffc000cc150c>] kmemleak_alloc+0x80/0xbc
[<ffffffc000303a7c>] kmem_cache_alloc_trace+0x120/0x1ac
[<ffffffc0006fa610>] hub_probe+0x120/0xb84
[<ffffffc000702b20>] usb_probe_interface+0x1ec/0x298
[<ffffffc0005d50cc>] driver_probe_device+0x160/0x374
[<ffffffc0005d5308>] __device_attach+0x28/0x4c
[<ffffffc0005d3164>] bus_for_each_drv+0x78/0xac
[<ffffffc0005d4ee0>] device_attach+0x6c/0x9c
[<ffffffc0005d42b8>] bus_probe_device+0x28/0xa0
[<ffffffc0005d23a4>] device_add+0x324/0x604
[<ffffffc000700fcc>] usb_set_configuration+0x660/0x6cc
[<ffffffc00070a350>] generic_probe+0x44/0x84
[<ffffffc000702914>] usb_probe_device+0x54/0x74
[<ffffffc0005d50cc>] driver_probe_device+0x160/0x374
[<ffffffc0005d5308>] __device_attach+0x28/0x4c
Deadlocks:
If the hub gets disconnected early enough (i.e. before INIT2/INIT3 are
finished and the init_work is still queued), the core may call
hub_quiesce() after acquiring interface device locks and it will wait
for the work to be cancelled synchronously. But if the work handler is
already running in parallel, it may try to acquire the same interface
device lock and this may result in deadlock.
Fix both the issues by removing the call to cancel_delayed_work_sync().
Fixes: e50293ef97 ("USB: fix invalid memory access in hub_activate()")
Reported-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e5b36ae2f8 upstream.
DWC3 has one interesting peculiarity with chained
transfers. If we setup N chained transfers and we
get a short packet before processing all N TRBs,
DWC3 will (conditionally) issue a XferComplete or
XferInProgress event and retire all TRBs from the
one which got a short packet to the last without
clearing their HWO bits.
This means SW must clear HWO bit manually, which
this patch is doing.
Cc: Brian E Rogers <brian.e.rogers@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c7de573471 upstream.
When using SG lists, we would end up setting
request->actual to:
num_mapped_sgs * (request->length - count)
Let's fix that up by incrementing request->actual
only once.
Reported-by: Brian E Rogers <brian.e.rogers@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 528d28138f upstream.
For case 14 and case 21, their correct return value is the number
of bytes transferred, so it is a positive integer. But in usbtest_ioctl,
it takes non-zero as false return value for usbtest_do_ioctl, so
it will treat the correct test as wrong test, then the time on
tests will be the minus value.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Fixes: 18fc4ebdc7 ("usb: misc: usbtest: Remove timeval usage")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5395875118 upstream.
In sg_timeout(), req->status is set to "-ETIMEDOUT" before calling
into usb_sg_cancel(). usb_sg_cancel() will do nothing and return
directly if req->status has been set to a non-zero value. This will
cause driver hang whenever transfer time out is triggered.
This patch fixes this issue. It could be backported to stable kernel
with version later than v3.15.
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 70f7ca9a02 upstream.
usbdev_mmap allocates a buffer. The size of the buffer is determined
by a user. So with this code (no need to be root):
int fd = open("/dev/bus/usb/001/001", O_RDONLY);
mmap(NULL, 0x800000, PROT_READ, MAP_SHARED, fd, 0);
we can see a warning:
WARNING: CPU: 0 PID: 21771 at ../mm/page_alloc.c:3563 __alloc_pages_slowpath+0x1036/0x16e0()
...
Call Trace:
[<ffffffff8117a3ae>] ? warn_slowpath_null+0x2e/0x40
[<ffffffff815178b6>] ? __alloc_pages_slowpath+0x1036/0x16e0
[<ffffffff81516880>] ? warn_alloc_failed+0x250/0x250
[<ffffffff8151226b>] ? get_page_from_freelist+0x75b/0x28b0
[<ffffffff815184e3>] ? __alloc_pages_nodemask+0x583/0x6b0
[<ffffffff81517f60>] ? __alloc_pages_slowpath+0x16e0/0x16e0
[<ffffffff810565d4>] ? dma_generic_alloc_coherent+0x104/0x220
[<ffffffffa0269e56>] ? hcd_buffer_alloc+0x1d6/0x3e0 [usbcore]
[<ffffffffa0269c80>] ? hcd_buffer_destroy+0xa0/0xa0 [usbcore]
[<ffffffffa0228f05>] ? usb_alloc_coherent+0x65/0x90 [usbcore]
[<ffffffffa0275c05>] ? usbdev_mmap+0x1a5/0x770 [usbcore]
...
Allocations like this one should be marked as __GFP_NOWARN. So do so.
The size could be also clipped by something like:
if (size >= (1 << (MAX_ORDER + PAGE_SHIFT - 1)))
return -ENOMEM;
But I think the overall limit of 16M (by usbfs_increase_memory_usage)
is enough, so that we only silence the warning here.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Steinar H. Gunderson <sesse@google.com>
Cc: Markus Rechberger <mrechberger@gmail.com>
Fixes: f7d34b445a (USB: Add support for usbfs zerocopy.)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bc337b5150 upstream.
In ehci_turn_off_all_ports() all EHCI port registers are cleared to zero.
On some hardware, this can lead to an system hang,
when ehci_port_power() accesses the already cleared registers.
This patch changes the order of cleanup.
First call ehci_port_power() which respects the current bits in
port status registers
and afterwards cleanup the hard way by setting everything to zero.
Signed-off-by: Marc Ohlf <ohlf@mkt-sys.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ae141830b1 upstream.
Commit 54b6680090 (parisc: Add native high-resolution sched_clock()
implementation) added support to use the CPU-internal cr16 counters as reliable
clocksource with the help of HAVE_UNSTABLE_SCHED_CLOCK.
Sadly the commit missed to remove the hack which prevented cr16 to become the
default clocksource even on SMP systems.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2fdea258fd upstream.
To be able to generate shared descriptors for AEAD, the authentication size
needs to be known. However, there is no imposed order of calling .setkey,
.setauthsize callbacks.
Thus, in case authentication size is not known at .setkey time, defer it
until .setauthsize is called.
The authsize != 0 check was incorrectly removed when converting the driver
to the new AEAD interface.
Fixes: 479bcc7c5b ("crypto: caam - Convert authenc to new AEAD interface")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d2d87e81e upstream.
There are a few things missed by the conversion to the
new AEAD interface:
1 - echainiv(authenc) encrypt shared descriptor
The shared descriptor is incorrect: due to the order of operations,
at some point in time MATH3 register is being overwritten.
2 - buffer used for echainiv(authenc) encrypt shared descriptor
Encrypt and givencrypt shared descriptors (for AEAD ops) are mutually
exclusive and thus use the same buffer in context state: sh_desc_enc.
However, there's one place missed by s/sh_desc_givenc/sh_desc_enc,
leading to errors when echainiv(authenc(...)) algorithms are used:
DECO: desc idx 14: Header Error. Invalid length or parity, or
certain other problems.
While here, also fix a typo: dma_mapping_error() is checking
for validity of sh_desc_givenc_dma instead of sh_desc_enc_dma.
Fixes: 479bcc7c5b ("crypto: caam - Convert authenc to new AEAD interface")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a0118c8b2b upstream.
Since 6de62f15b5 ("crypto: algif_hash - Require setkey before
accept(2)"), the AF_ALG interface requires userspace to provide a key
to any algorithm that has a setkey method. However, the non-HMAC
algorithms are not keyed, so setting a key is unnecessary.
Fix this by removing the setkey method from the non-keyed hash
algorithms.
Fixes: 6de62f15b5 ("crypto: algif_hash - Require setkey before accept(2)")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f3b0946d62 upstream.
Bharat Kumar Gogada reported issues with the generic MSI code, where the
end-point ended up with garbage in its MSI configuration (both for the vector
and the message).
It turns out that the two MSI paths in the kernel are doing slightly different
things:
generic MSI: disable MSI -> allocate MSI -> enable MSI -> setup EP
PCI MSI: disable MSI -> allocate MSI -> setup EP -> enable MSI
And it turns out that end-points are allowed to latch the content of the MSI
configuration registers as soon as MSIs are enabled. In Bharat's case, the
end-point ends up using whatever was there already, which is not what you
want.
In order to make things converge, we introduce a new MSI domain flag
(MSI_FLAG_ACTIVATE_EARLY) that is unconditionally set for PCI/MSI. When set,
this flag forces the programming of the end-point as soon as the MSIs are
allocated.
A consequence of this is that we have an extra activate in irq_startup, but
that should be without much consequence.
tglx:
- Several people reported a VMWare regression with PCI/MSI-X passthrough. It
turns out that the patch also cures that issue.
- We need to have a look at the MSI disable interrupt path, where we write
the msg to all zeros without disabling MSI in the PCI device. Is that
correct?
Fixes: 52f518a3a7 "x86/MSI: Use hierarchical irqdomains to manage MSI interrupts"
Reported-and-tested-by: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com>
Reported-and-tested-by: Foster Snowhill <forst@forstwoof.ru>
Reported-by: Matthias Prager <linux@matthiasprager.de>
Reported-by: Jason Taylor <jason.taylor@simplivity.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
Link: http://lkml.kernel.org/r/1468426713-31431-1-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dad2232844 upstream.
Commit e41f501d39 ("vmlinux.lds: account for destructor sections")
added '.text.exit' to EXIT_TEXT which is discarded at link time by default.
This breaks compilation of UML:
`.text.exit' referenced in section `.fini_array' of
/usr/lib/gcc/x86_64-linux-gnu/6/../../../x86_64-linux-gnu/libc.a(sdlerror.o):
defined in discarded section `.text.exit' of
/usr/lib/gcc/x86_64-linux-gnu/6/../../../x86_64-linux-gnu/libc.a(sdlerror.o)
Apparently UML doesn't want to discard exit text, so let's place all EXIT_TEXT
sections in .exit.text.
Fixes: e41f501d39 ("vmlinux.lds: account for destructor sections")
Reported-by: Stefan Traby <stefan@hello-penguin.com>
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Acked-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2324d15447 upstream.
When CPPC fails to request a PCC channel, the CPC data is freed
and cpc_desc_ptr points to the invalid data.
Avoid this issue by moving the cpc_desc_ptr assignment after the PCC
channel request.
Signed-off-by: Hoan Tran <hotran@apm.com>
Acked-by: Ashwin Chaugule <ashwin.chaugule@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8343c40d3d upstream.
Based on 8.4.7.1 section of ACPI 6.1 specification, if the platform
supports CPPC, the _CPC object must exist under all processor objects.
If cpc_desc_ptr pointer is invalid on any CPUs, acpi_get_psd_map()
should return error and CPPC cpufreq driver can not be registered.
Signed-off-by: Hoan Tran <hotran@apm.com>
Reviewed-by: Prashanth Prakash <pprakash@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 68202c9f0a upstream.
The "NVDIMM Block Window Driver Writer's Guide":
http://pmem.io/documents/NVDIMM_DriverWritersGuide-July-2016.pdf
...defines the layout of the block window status register. For the July
2016 version of the spec linked to above, this happens in Figure 4 on
page 26.
The only bits defined in this spec are bits 31, 5, 4, 2, 1 and 0. The
rest of the bits in the status register are reserved, and there is a
warning following the diagram that says:
Note: The driver cannot assume the value of the RESERVED bits in the
status register are zero. These reserved bits need to be masked off, and
the driver must avoid checking the state of those bits.
This change ensures that for hardware implementations that set these
reserved bits in the status register, the driver won't incorrectly fail the
block I/Os.
Reviewed-by: Lee, Chun-Yi <jlee@suse.com>
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d918fb13a upstream.
In order to successfully decode Intel PT traces, context switch events
are needed from the moment the trace starts. Currently that is ensured
by using the 'immediate' flag which enables the switch event when it is
opened.
However, since commit 86c2786994 ("perf intel-pt: Add support for
PERF_RECORD_SWITCH") that might not always happen. When tracing
system-wide the context switch event is added to the tracking event
which was not set as 'immediate'. Change that so it is.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Fixes: 86c2786994 ("perf intel-pt: Add support for PERF_RECORD_SWITCH")
Link: http://lkml.kernel.org/r/1471245784-22580-1-git-send-email-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c87edb3611 upstream.
The symbols used in the tick_stop tracepoint were not being converted
properly into integers in the trace_stop format file. Instead we had this:
print fmt: "success=%d dependency=%s", REC->success,
__print_symbolic(REC->dependency, { 0, "NONE" },
{ (1 << TICK_DEP_BIT_POSIX_TIMER), "POSIX_TIMER" },
{ (1 << TICK_DEP_BIT_PERF_EVENTS), "PERF_EVENTS" },
{ (1 << TICK_DEP_BIT_SCHED), "SCHED" },
{ (1 << TICK_DEP_BIT_CLOCK_UNSTABLE), "CLOCK_UNSTABLE" })
User space tools have no idea how to parse "TICK_DEP_BIT_SCHED" or the other
symbols used to do the bit shifting. The reason is that the conversion was
done with using the TICK_DEP_MASK_* symbols which are just macros that
convert to the BIT shift itself (with the exception of NONE, which was
converted properly, because it doesn't use bits, and is defined as zero).
The TICK_DEP_BIT_* needs to be denoted by TRACE_DEFINE_ENUM() in order to
have this properly converted for user space tools to parse this event.
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Fixes: e6e6cc22e0 ("nohz: Use enum code for tick stop failure tracing message")
Reported-by: Luiz Capitulino <lcapitulino@redhat.com>
Tested-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c8952a7075 upstream.
There are multiple cases in vfio_pci_set_ctx_trigger_single() where
we assume we can safely read from our data pointer without actually
checking whether the user has passed any data via the count field.
VFIO_IRQ_SET_DATA_NONE in particular is entirely broken since we
attempt to pull an int32_t file descriptor out before even checking
the data type. The other data types assume the data pointer contains
one element of their type as well.
In part this is good news because we were previously restricted from
doing much sanitization of parameters because it was missed in the
past and we didn't want to break existing users. Clearly DATA_NONE
is completely broken, so it must not have any users and we can fix
it up completely. For DATA_BOOL and DATA_EVENTFD, we'll just
protect ourselves, returning error when count is zero since we
previously would have oopsed.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reported-by: Chris Thompson <the_cartographer@hotmail.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6039892396 upstream.
With debugobjects enabled and using SLAB_DESTROY_BY_RCU, when a
kmem_cache_node is destroyed the call_rcu() may trigger a slab
allocation to fill the debug object pool (__debug_object_init:fill_pool).
Everywhere but during kmem_cache_destroy(), discard_slab() is performed
outside of the kmem_cache_node->list_lock and avoids a lockdep warning
about potential recursion:
=============================================
[ INFO: possible recursive locking detected ]
4.8.0-rc1-gfxbench+ #1 Tainted: G U
---------------------------------------------
rmmod/8895 is trying to acquire lock:
(&(&n->list_lock)->rlock){-.-...}, at: [<ffffffff811c80d7>] get_partial_node.isra.63+0x47/0x430
but task is already holding lock:
(&(&n->list_lock)->rlock){-.-...}, at: [<ffffffff811cbda4>] __kmem_cache_shutdown+0x54/0x320
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&n->list_lock)->rlock);
lock(&(&n->list_lock)->rlock);
*** DEADLOCK ***
May be due to missing lock nesting notation
5 locks held by rmmod/8895:
#0: (&dev->mutex){......}, at: driver_detach+0x42/0xc0
#1: (&dev->mutex){......}, at: driver_detach+0x50/0xc0
#2: (cpu_hotplug.dep_map){++++++}, at: get_online_cpus+0x2d/0x80
#3: (slab_mutex){+.+.+.}, at: kmem_cache_destroy+0x3c/0x220
#4: (&(&n->list_lock)->rlock){-.-...}, at: __kmem_cache_shutdown+0x54/0x320
stack backtrace:
CPU: 6 PID: 8895 Comm: rmmod Tainted: G U 4.8.0-rc1-gfxbench+ #1
Hardware name: Gigabyte Technology Co., Ltd. H87M-D3H/H87M-D3H, BIOS F11 08/18/2015
Call Trace:
__lock_acquire+0x1646/0x1ad0
lock_acquire+0xb2/0x200
_raw_spin_lock+0x36/0x50
get_partial_node.isra.63+0x47/0x430
___slab_alloc.constprop.67+0x1a7/0x3b0
__slab_alloc.isra.64.constprop.66+0x43/0x80
kmem_cache_alloc+0x236/0x2d0
__debug_object_init+0x2de/0x400
debug_object_activate+0x109/0x1e0
__call_rcu.constprop.63+0x32/0x2f0
call_rcu+0x12/0x20
discard_slab+0x3d/0x40
__kmem_cache_shutdown+0xdb/0x320
shutdown_cache+0x19/0x60
kmem_cache_destroy+0x1ae/0x220
i915_gem_load_cleanup+0x14/0x40 [i915]
i915_driver_unload+0x151/0x180 [i915]
i915_pci_remove+0x14/0x20 [i915]
pci_device_remove+0x34/0xb0
__device_release_driver+0x95/0x140
driver_detach+0xb6/0xc0
bus_remove_driver+0x53/0xd0
driver_unregister+0x27/0x50
pci_unregister_driver+0x25/0x70
i915_exit+0x1a/0x1e2 [i915]
SyS_delete_module+0x193/0x1f0
entry_SYSCALL_64_fastpath+0x1c/0xac
Fixes: 52b4b950b5 ("mm: slab: free kmem_cache_node after destroy sysfs file")
Link: http://lkml.kernel.org/r/1470759070-18743-1-git-send-email-chris@chris-wilson.co.uk
Reported-by: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Dmitry Safonov <dsafonov@virtuozzo.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 58625edf9e upstream.
When using the indirect buffers feature, 'desc' is allocated in
virtqueue_add() but isn't freed before leaving on a ring full error,
causing a memory leak.
For example, it seems rather clear that this can trigger
with virtio net if mergeable buffers are not used.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3eb53b20d7 upstream.
When building gccgo in userspace, errno.h gets parsed and the go include file
sysinfo.go is generated.
Since EREFUSED is defined to the same value as ECONNREFUSED, and ECONNREFUSED
is defined later on in errno.h, this leads to go complaining that EREFUSED
isn't defined yet.
Fix this trivial problem by moving the define of EREFUSED down after
ECONNREFUSED in errno.h (and clean up the indenting while touching this line).
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3146bc64d1 upstream.
AT_VECTOR_SIZE_ARCH should be defined with the maximum number of
NEW_AUX_ENT entries that ARCH_DLINFO can contain, but it wasn't defined
for arm64 at all even though ARCH_DLINFO will contain one NEW_AUX_ENT
for the VDSO address.
This shouldn't be a problem as AT_VECTOR_SIZE_BASE includes space for
AT_BASE_PLATFORM which arm64 doesn't use, but lets define it now and add
the comment above ARCH_DLINFO as found in several other architectures to
remind future modifiers of ARCH_DLINFO to keep AT_VECTOR_SIZE_ARCH up to
date.
Fixes: f668cd1673 ("arm64: ELF definitions")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a52ff34e5e upstream.
For SKL and later Intel chips, we control the power well per codec
basis via link_power callback since the commit [03b135cebc: ALSA:
hda - remove dependency on i915 power well for SKL].
However, there are a few exceptional cases where the gfx registers are
accessed from the audio driver: namely the wakeup override bit
toggling at (both system and runtime) resume. This seems causing a
kernel warning when accessed during the power well down (and likely
resulting in the bogus register accesses).
This patch puts the proper power up / down sequence around the resume
code so that the wakeup bit is fiddled properly while the power is
up. (The other callback, sync_audio_rate, is used only in the PCM
callback, so it's guaranteed in the power-on.)
Also, by this proper power up/down, the instantaneous flip of wakeup
bit in the resume callback that was introduced by the commit
[033ea349a7: ALSA: hda - Fix Skylake codec timeout] becomes
superfluous, as snd_hdac_display_power() already does it. So we can
clean it up together.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96214
Fixes: 03b135cebc ('ALSA: hda - remove dependency on i915 power well for SKL')
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7627e40c66 upstream.
VF0610 does not support reading the sample rate which leads to many
lines of "cannot get freq at ep 0x82". This patch adds the USB ID
(0x041E:4080) to snd_usb_get_sample_rate_quirk() list.
Signed-off-by: Piotr Karasinski <peter.karasinski@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9130b8dbc6 upstream.
It's possible to have simultaneous upcalls for the same UIDs but
different GSS service. In that case, we need to allow for the
upcall to gssd to proceed so that not the same context is used
by two different GSS services. Some servers lock the use of context
to the GSS service.
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f4c17a03b upstream.
If the connect attempt immediately fails with an EADDRNOTAVAIL error, then
that means our choice of source port number was bad.
This error is expected when we set the SO_REUSEPORT socket option and we
have 2 sockets sharing the same source and destination address and port
combinations.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Fixes: 402e23b4ed ("SUNRPC: Fix stupid typo in xs_sock_set_reuseport")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d8d378fa1a upstream.
The unit tests crash when hotplug races the previous probe. This race
requires that the loading of the nfit_test module be terminated with
SIGTERM, and the module to be unloaded while the ars scan is still
running.
In contrast to the normal nfit driver, the unit test calls
acpi_nfit_init() twice to simulate hotplug, whereas the nominal case
goes through the acpi_nfit_notify() event handler. The
acpi_nfit_notify() path is careful to flush the previous region
registration before servicing the hotplug event. The unit test was
missing this guarantee.
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffff810cdce7>] pwq_activate_delayed_work+0x47/0x170
[..]
Call Trace:
[<ffffffff810ce186>] pwq_dec_nr_in_flight+0x66/0xa0
[<ffffffff810ce490>] process_one_work+0x2d0/0x680
[<ffffffff810ce331>] ? process_one_work+0x171/0x680
[<ffffffff810ce88e>] worker_thread+0x4e/0x480
[<ffffffff810ce840>] ? process_one_work+0x680/0x680
[<ffffffff810ce840>] ? process_one_work+0x680/0x680
[<ffffffff810d5343>] kthread+0xf3/0x110
[<ffffffff8199846f>] ret_from_fork+0x1f/0x40
[<ffffffff810d5250>] ? kthread_create_on_node+0x230/0x230
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f72075c9ed upstream.
This problem has actually been in the UV code for a while, but we didn't
catch it until recently, because we had been relying on EFI_OLD_MEMMAP
to allow our systems to boot for a period of time. We noticed the issue
when trying to kexec a recent community kernel, where we hit this NULL
pointer dereference in efi_sync_low_kernel_mappings():
[ 0.337515] BUG: unable to handle kernel NULL pointer dereference at 0000000000000880
[ 0.346276] IP: [<ffffffff8105df8d>] efi_sync_low_kernel_mappings+0x5d/0x1b0
The problem doesn't show up with EFI_OLD_MEMMAP because we skip the
chunk of setup_efi_state() that sets the efi_loader_signature for the
kexec'd kernel. When the kexec'd kernel boots, it won't set EFI_BOOT in
setup_arch, so we completely avoid the bug.
We always kexec with noefi on the command line, so this shouldn't be an
issue, but since we're not actually checking for efi_runtime_disabled in
uv_bios_init(), we end up trying to do EFI runtime callbacks when we
shouldn't be. This patch just adds a check for efi_runtime_disabled in
uv_bios_init() so that we don't map in uv_systab when runtime_disabled ==
true.
Signed-off-by: Alex Thorlton <athorlton@sgi.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Borislav Petkov <bp@suse.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Travis <travis@sgi.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russ Anderson <rja@sgi.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/1470912120-22831-2-git-send-email-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5cf0791da5 upstream.
There's a subtle preemption race on UP kernels:
Usually current->mm (and therefore mm->pgd) stays the same during the
lifetime of a task so it does not matter if a task gets preempted during
the read and write of the CR3.
But then, there is this scenario on x86-UP:
TaskA is in do_exit() and exit_mm() sets current->mm = NULL followed by:
-> mmput()
-> exit_mmap()
-> tlb_finish_mmu()
-> tlb_flush_mmu()
-> tlb_flush_mmu_tlbonly()
-> tlb_flush()
-> flush_tlb_mm_range()
-> __flush_tlb_up()
-> __flush_tlb()
-> __native_flush_tlb()
At this point current->mm is NULL but current->active_mm still points to
the "old" mm.
Let's preempt taskA _after_ native_read_cr3() by taskB. TaskB has its
own mm so CR3 has changed.
Now preempt back to taskA. TaskA has no ->mm set so it borrows taskB's
mm and so CR3 remains unchanged. Once taskA gets active it continues
where it was interrupted and that means it writes its old CR3 value
back. Everything is fine because userland won't need its memory
anymore.
Now the fun part:
Let's preempt taskA one more time and get back to taskB. This
time switch_mm() won't do a thing because oldmm (->active_mm)
is the same as mm (as per context_switch()). So we remain
with a bad CR3 / PGD and return to userland.
The next thing that happens is handle_mm_fault() with an address for
the execution of its code in userland. handle_mm_fault() realizes that
it has a PTE with proper rights so it returns doing nothing. But the
CPU looks at the wrong PGD and insists that something is wrong and
faults again. And again. And one more time…
This pagefault circle continues until the scheduler gets tired of it and
puts another task on the CPU. It gets little difficult if the task is a
RT task with a high priority. The system will either freeze or it gets
fixed by the software watchdog thread which usually runs at RT-max prio.
But waiting for the watchdog will increase the latency of the RT task
which is no good.
Fix this by disabling preemption across the critical code section.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Borislav Petkov <bp@suse.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/1470404259-26290-1-git-send-email-bigeasy@linutronix.de
[ Prettified the changelog. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b8612e517c upstream.
Signing a module should only make it trusted by the specific kernel it
was built for, not anything else. If a module signing key is used for
multiple ABI-incompatible kernels, the modules need to include enough
version information to distinguish them.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bca014caaa upstream.
Signing a module should only make it trusted by the specific kernel it
was built for, not anything else. Loading a signed module meant for a
kernel with a different ABI could have interesting effects.
Therefore, treat all signatures as invalid when a module is
force-loaded.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 99f3c90d0d upstream.
When the corrupt_bio_byte feature was introduced it caused READ bios to
no longer be errored with -EIO during the down_interval. This had to do
with the complexity of needing to submit READs if the corrupt_bio_byte
feature was used.
Fix it so READ bios are properly errored with -EIO; doing so early in
flakey_map() as long as there isn't a match for the corrupt_bio_byte
feature.
Fixes: a3998799fb ("dm flakey: add corrupt_bio_byte feature")
Reported-by: Akira Hayakawa <ruby.wktk@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 70c96dfac0 upstream.
As per code flow s3c_rtc_setfreq() will get called with rtc clock disabled
and in set_freq we perform h/w registers read/write, which results in a
kernel crash on exynos7 platform while probing rtc driver.
Below is code flow:
s3c_rtc_probe()
clk_prepare_enable(info->rtc_clk) // rtc clock enabled
s3c_rtc_gettime() // will enable clk if not done, and disable it upon exit
s3c_rtc_setfreq() //then this will be called with clk disabled
This patch take cares of such issue by adding s3c_rtc_{enable/disable}_clk in
s3c_rtc_setfreq().
Fixes: 24e1455493 ("drivers/rtc/rtc-s3c.c: delete duplicate clock control")
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Tested-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e1191bd4f6 upstream.
A regression is caused by the following commit:
Commit: 02b771b64b
Subject: ACPI / EC: Fix an issue caused by the serialized _Qxx evaluations
In this commit, using system workqueue causes that the maximum parallel
executions of _Qxx can exceed 255. This violates the method reentrancy
limit in ACPICA and generates the following error log:
ACPI Error: Method reached maximum reentrancy limit (255) (20150818/dsmethod-341)
This patch creates a seperate workqueue and limits the number of parallel
_Qxx evaluations down to a configurable value (can be tuned against number
of online CPUs).
Since EC events are handled after driver probe, we can create the workqueue
in acpi_ec_init().
Fixes: 02b771b64b (ACPI / EC: Fix an issue caused by the serialized _Qxx evaluations)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=135691
Reported-and-tested-by: Helen Buus <ubuntu@hbuus.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb27570525 upstream.
On Intel Merrifield platform several PCI devices have a bogus configuration,
i.e. the IRQ0 had been assigned to few of them. These are PCI root bridge,
eMMC0, HS UART common registers, PWM, and HDMI. The actual interrupt line can
be allocated to one device exclusively, in our case to eMMC0, the rest should
cope without it and basically known drivers for them are not using interrupt
line at all.
Rework IRQ0 workaround, which was previously done to avoid conflict between
eMMC0 and HS UART common registers, to behave differently based on the device
in question, i.e. allocate interrupt line to eMMC0, but silently skip interrupt
allocation for the rest except HS UART common registers which are not used
anyway. With this rework IOSF MBI driver in particular would be used.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Fixes: 39d9b77b8d ("x86/pci/intel_mid_pci: Work around for IRQ0 assignment")
Link: http://lkml.kernel.org/r/1465842481-136852-1-git-send-email-andriy.shevchenko@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9ac0108c2b upstream.
Similar to the AR93xx series, the AR94xx and the Qualcomm QCA988x also have
the same quirk for the Bus Reset.
Fixes: c3e59ee4e7 ("PCI: Mark Atheros AR93xx to avoid bus reset")
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ef0665398 upstream.
At first, we prefer to use mips clockevent device, so we decrease the
rating of hpet clockevent device.
For hpet, if HPET_MIN_PROG_DELTA (minimum delta of hpet programming) is
too small and HPET_MIN_CYCLES (threshold of -ETIME checking) is too
large, then hpet_next_event() can easily return -ETIME. After commit
c6eb3f70d4 ("hrtimer: Get rid of hrtimer softirq") this will cause
a RCU stall.
So, HPET_MIN_PROG_DELTA must be sufficient that we don't re-trip the
-ETIME check -- if we do, we will return -ETIME, forward the next event
time, try to set it, return -ETIME again, and basically lock the system
up. Meanwhile, HPET_MIN_CYCLES doesn't need to be too large, 16 cycles
is enough.
This solution is similar to commit f9eccf2461 ("clocksource/drivers
/vt8500: Increase the minimum delta").
By the way, this patch ensures hpet count/compare to be 32-bit long.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J . Hill <Steven.Hill@imgtec.com>
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13819/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit db1bb44c4c upstream.
We're always tracing IPv4 or IPv6 addresses, so we can save a lot
of space on the ringbuffer by allocating the correct sockaddr size.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Fixes: 83a712e0af "sunrpc: add some tracepoints around ..."
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2de4fcc646 upstream.
Some ASUS laptops were shipped with touchpads that require to be woken up
first, before trying to switch them into absolute reporting mode, otherwise
touchpad would fail to work while flooding the logs with:
elan_i2c i2c-ELAN1000:00: invalid report id data (1)
Among affected devices are Asus E202SA, N552VW, X456UF, UX305CA, and
others. We detect such devices by checking the IC type and product ID
numbers and adjusting order of operations accordingly.
Signed-off-by: KT Liao <kt.liao@emc.com.tw>
Reported-by: Chris Chiu <chiu@endlessm.com>
Reported-by: Vlad Glagolev <stealth@vaygr.net>
Tested-by: Vlad Glagolev <stealth@vaygr.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 57a05d83b1 upstream.
We are in atomic context and must not sleep.
Sleeping here is possible since malloc() maps
to kmalloc() with GFP_KERNEL.
Fixes: b6024b21 ("um: extend fpstate to _xstate to support YMM registers")
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 410c29dfbf upstream.
If a Simple command is sent with a failure, target_setup_cmd_from_cdb
returns with TCM_UNSUPPORTED_SCSI_OPCODE or TCM_INVALID_CDB_FIELD.
So in the cases where target_setup_cmd_from_cdb returns an error, we
never get far enough to call target_execute_cmd to increment simple_cmds.
Since simple_cmds isn't incremented, the result of the failure from
target_setup_cmd_from_cdb causes transport_generic_request_failure to
decrement simple_cmds, due to call to transport_complete_task_attr.
With this dev->simple_cmds or dev->dev_ordered_sync is now -1, not 0.
So when a subsequent command with an Ordered Task is sent, it causes
a hang, since dev->simple_cmds is at -1.
Tested-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Tested-by: Michael Cyr <mikecyr@linux.vnet.ibm.com>
Signed-off-by: Michael Cyr <mikecyr@linux.vnet.ibm.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea263c7fad upstream.
max_discard_sectors only 32bits, and some non scsi backend
devices will set this to the max 0xffffffff, so we can end up
overflowing during the max_unmap_lba_count calculation.
This fixes a regression caused by my patch:
commit 8a9ebe717a
Author: Mike Christie <mchristi@redhat.com>
Date: Mon Jan 18 14:09:27 2016 -0600
target: Fix WRITE_SAME/DISCARD conversion to linux 512b sectors
which can result in extra discards being sent to due the overflow
causing max_unmap_lba_count to be smaller than what the backing
device can actually support.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 064cdd2d91 upstream.
This patch fixes a race in iscsit_release_commands_from_conn() ->
iscsit_free_cmd() -> transport_generic_free_cmd() + wait_for_tasks=1,
where CMD_T_FABRIC_STOP could end up being set after the final
kref_put() is called from core_tmr_abort_task() context.
This results in transport_generic_free_cmd() blocking indefinately
on se_cmd->cmd_wait_comp, because the target_release_cmd_kref()
check for CMD_T_FABRIC_STOP returns false.
To address this bug, make iscsit_release_commands_from_conn()
do list_splice and set CMD_T_FABRIC_STOP early while holding
iscsi_conn->cmd_lock. Also make iscsit_aborted_task() only
remove iscsi_cmd_t if CMD_T_FABRIC_STOP has not already been
set.
Finally in target_release_cmd_kref(), only honor fabric_stop
if CMD_T_ABORTED has been set.
Cc: Mike Christie <mchristi@redhat.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Tested-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e2c956b8a upstream.
During transport_generic_free_cmd() with a concurrent TMR
ABORT_TASK and shutdown CMD_T_FABRIC_STOP bit set, the
caller will be blocked on se_cmd->cmd_wait_stop completion
until the final kref_put() -> target_release_cmd_kref()
has been invoked to call complete().
However, when ABORT_TASK is completed with FUNCTION_COMPLETE
in core_tmr_abort_task(), the aborted se_cmd will have already
been removed from se_sess->sess_cmd_list via list_del_init().
This results in target_release_cmd_kref() hitting the
legacy list_empty() == true check, invoking ->release_cmd()
but skipping complete() to wakeup se_cmd->cmd_wait_stop
blocked earlier in transport_generic_free_cmd() code.
To address this bug, it's safe to go ahead and drop the
original list_empty() check so that fabric_stop invokes
the complete() as expected, since list_del_init() can
safely be used on a empty list.
Cc: Mike Christie <mchristi@redhat.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Tested-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dff0ca9ea7 upstream.
If a command with a Simple task attribute is failed due to a Unit
Attention, then a subsequent command with an Ordered task attribute
will hang forever. The reason for this is that the Unit Attention
status is checked for in target_setup_cmd_from_cdb, before the call
to target_execute_cmd, which calls target_handle_task_attr, which
in turn increments dev->simple_cmds.
However, transport_generic_request_failure still calls
transport_complete_task_attr, which will decrement dev->simple_cmds.
In this case, simple_cmds is now -1. So when a command with the
Ordered task attribute is sent, target_handle_task_attr sees that
dev->simple_cmds is not 0, so it decides it can't execute the
command until all the (nonexistent) Simple commands have completed.
Reported-by: Michael Cyr <mikecyr@linux.vnet.ibm.com>
Tested-by: Michael Cyr <mikecyr@linux.vnet.ibm.com>
Reported-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Tested-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8abc718de6 upstream.
In MC/S scenario, the conn->sess has been set NULL in
iscsi_login_non_zero_tsih_s1 when the second connection comes here,
then kernel panic.
The conn->sess will be assigned in iscsi_login_non_zero_tsih_s2. So
we should check whether it's NULL before calling.
Signed-off-by: Feng Li <lifeng1519@gmail.com>
Tested-by: Sumit Rai <sumit.rai@calsoftinc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 714fb87e8b upstream.
Install the UBI device object before we arm sysfs.
Otherwise udev tries to read sysfs attributes before UBI is ready and
udev rules will not match.
Signed-off-by: Iosif Harutyunov <iharutyunov@sonicwall.com>
[rw: massaged commit message]
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bc743f34df upstream.
We cannot use ubi_* logging functions before the UBI
object is initialized.
Fixes: 3260870331 ("UBI: Extend UBI layer debug/messaging capabilities")
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4946784bd3 upstream.
When the volume resize operation shrinks a volume,
LEBs will be unmapped. Since unmapping will not erase these
LEBs immediately we have to wait for that operation to finish.
Otherwise in case of a power cut right after writing the new
volume table the UBI attach process can find more LEBs than the
volume table knows. This will render the UBI image unattachable.
Fix this issue by waiting for erase to complete and write the new
volume table afterward.
Reported-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d9fc880723 upstream.
Fix a memory leak resulting from memory allocation in safe_name().
This patch fixes all call sites of safe_name().
Mathieu Malaterre reported the memory leak on boot:
On my PowerMac device-tree would generate a duplicate name:
[ 0.023043] device-tree: Duplicate name in PowerPC,G4@0, renamed to "l2-cache#1"
in this case a newly allocated name is generated by `safe_name`. However
in this case it is never deallocated.
The bug was found using kmemleak reported as:
unreferenced object 0xdf532e60 (size 32):
comm "swapper", pid 1, jiffies 4294892300 (age 1993.532s)
hex dump (first 32 bytes):
6c 32 2d 63 61 63 68 65 23 31 00 dd e4 dd 1e c2 l2-cache#1......
ec d4 ba ce 04 ec cc de 8e 85 e9 ca c4 ec cc 9e ................
backtrace:
[<c02d3350>] kvasprintf+0x64/0xc8
[<c02d3400>] kasprintf+0x4c/0x5c
[<c0453814>] safe_name.isra.1+0x80/0xc4
[<c04545d8>] __of_attach_node_sysfs+0x6c/0x11c
[<c075f21c>] of_core_init+0x8c/0xf8
[<c0729594>] kernel_init_freeable+0xd4/0x208
[<c00047e8>] kernel_init+0x24/0x11c
[<c00158ec>] ret_from_kernel_thread+0x5c/0x64
Link: https://bugzilla.kernel.org/show_bug.cgi?id=120331
Signed-off-by: Frank Rowand <frank.rowand@am.sony.com>
Reported-by: mathieu.malaterre@gmail.com
Tested-by: Mathieu Malaterre <mathieu.malaterre@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b0ffeb537f upstream.
Number of outstanding_pi may overflow and as a result may indicate that
there are no elements in the queue. The effect of doing this is that the
MAD layer will get stuck waiting for completions. The MAD layer will
think that the QP is full - because it didn't receive these completions.
This fix changes it so the outstanding_pi number is increased
with 32-bit wraparound and is not limited to max_send_wr so
that the difference between outstanding_pi and outstanding_ci will
really indicate the number of outstanding completions.
Fixes: ea6dc20362 ('IB/mlx5: Reorder GSI completions')
Signed-off-by: Slava Shwartsman <slavash@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Haggai Eran <haggaie@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 59ec4b57bc upstream.
One of the machines has ALC255 on it, another one has ALC298 on it.
On the machine with the codec ALC298, it also has the speaker volume
problem, so we add the fixup chained to ALC298_FIXUP_SPK_VOLUME rather
than adding a group of pin definition in the pin quirk table, since
the speak volume problem does not happen on other machines yet.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd9aa335c8 upstream.
We have a Dell AIO on which we can't adjust its speaker's volume.
The problem is it is connected to a Audio Output node without Amp-out
capability. To fix it, we change it to be connnected to a node with
Amp-out capability.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 33baefe5e7 upstream.
krealloc() doesn't work always properly with __GFP_ZERO flag as
expected. For clearing the reallocated area, we need to clear
explicitly instead.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 144f4c9839 upstream.
nand_do_write_ops() determines if it is writing a partial page with the
formula:
part_pagewr = (column || writelen < (mtd->writesize - 1))
When 'writelen' is exactly 1 byte less than the NAND page size the formula
equates to zero, so the code doesn't process it as a partial write,
although it should.
As a consequence the function remains in the while(1) loop with 'writelen'
becoming 0xffffffff and iterating endlessly.
The bug may not be easy to reproduce in Linux since user space tools
usually force the padding or round-up the write size to a page-size
multiple.
This was discovered in U-Boot where the issue can be reproduced by
writing any size that is 1 byte less than a page-size multiple.
For example, on a NAND with 2K page (0x800):
=> nand erase.part <partition>
=> nand write $loadaddr <partition> 7ff
[Editor's note: the bug was added in commit 29072b9607, but moved
around in commit 66507c7bc8 ("mtd: nand: Add support to use nand_base
poi databuf as bounce buffer")]
Fixes: 29072b9607 ("[MTD] NAND: add subpage write support")
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff06db1efb upstream.
Commit 09954bad4 ("floppy: refactor open() flags handling"), as a
side-effect, causes open(/dev/fdX, O_ACCMODE) to fail. It turns out that
this is being used setfdprm userspace for ioctl-only open().
Reintroduce back the original behavior wrt !(FMODE_READ|FMODE_WRITE)
modes, while still keeping the original O_NDELAY bug fixed.
Reported-by: Wim Osterholt <wim@djo.tudelft.nl>
Tested-by: Wim Osterholt <wim@djo.tudelft.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df08c32ce3 upstream.
The name for a bdi of a gendisk is derived from the gendisk's devt.
However, since the gendisk is destroyed before the bdi it leaves a
window where a new gendisk could dynamically reuse the same devt while a
bdi with the same name is still live. Arrange for the bdi to hold a
reference against its "owner" disk device while it is registered.
Otherwise we can hit sysfs duplicate name collisions like the following:
WARNING: CPU: 10 PID: 2078 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x64/0x80
sysfs: cannot create duplicate filename '/devices/virtual/bdi/259:1'
Hardware name: HP ProLiant DL580 Gen8, BIOS P79 05/06/2015
0000000000000286 0000000002c04ad5 ffff88006f24f970 ffffffff8134caec
ffff88006f24f9c0 0000000000000000 ffff88006f24f9b0 ffffffff8108c351
0000001f0000000c ffff88105d236000 ffff88105d1031e0 ffff8800357427f8
Call Trace:
[<ffffffff8134caec>] dump_stack+0x63/0x87
[<ffffffff8108c351>] __warn+0xd1/0xf0
[<ffffffff8108c3cf>] warn_slowpath_fmt+0x5f/0x80
[<ffffffff812a0d34>] sysfs_warn_dup+0x64/0x80
[<ffffffff812a0e1e>] sysfs_create_dir_ns+0x7e/0x90
[<ffffffff8134faaa>] kobject_add_internal+0xaa/0x320
[<ffffffff81358d4e>] ? vsnprintf+0x34e/0x4d0
[<ffffffff8134ff55>] kobject_add+0x75/0xd0
[<ffffffff816e66b2>] ? mutex_lock+0x12/0x2f
[<ffffffff8148b0a5>] device_add+0x125/0x610
[<ffffffff8148b788>] device_create_groups_vargs+0xd8/0x100
[<ffffffff8148b7cc>] device_create_vargs+0x1c/0x20
[<ffffffff811b775c>] bdi_register+0x8c/0x180
[<ffffffff811b7877>] bdi_register_dev+0x27/0x30
[<ffffffff813317f5>] add_disk+0x175/0x4a0
Reported-by: Yi Zhang <yizhan@redhat.com>
Tested-by: Yi Zhang <yizhan@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed up missing 0 return in bdi_register_owner().
Signed-off-by: Jens Axboe <axboe@fb.com>
commit 20bd723ec6 upstream.
When a bio is cloned, the newly created bio must be associated with
the same blkcg as the original bio (if BLK_CGROUP is enabled). If
this operation is not performed, then the new bio is not associated
with any group, and the group of the current task is returned when
the group of the bio is requested.
Depending on the cloning frequency, this may cause a large
percentage of the bios belonging to a given group to be treated
as if belonging to other groups (in most cases as if belonging to
the root group). The expected group isolation may thereby be broken.
This commit adds the missing association in bio-cloning functions.
Fixes: da2f0f74cf ("Btrfs: add support for blkio controllers")
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Reviewed-by: Nikolay Borisov <kernel@kyup.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6154c187b9 upstream.
The LNKGET based atomic sequence in __cmpxchg_u32 has slightly incorrect
constraints for the return value which under certain circumstances can
allow an address unit register to be used as the first operand of a CMP
instruction. This isn't a valid instruction however as the encodings
only allow a data unit to be specified. This would result in an
assembler error like the following:
Error: failed to assemble instruction: "CMP A0.2,D0Ar6"
Fix by changing the constraint from "=&da" (assigned, early clobbered,
data or address unit register) to "=&d" (data unit register only).
The constraint for the second operand, "bd" (an op2 register where op1
is a data unit register and the instruction supports O2R) is already
correct assuming the first operand is a data unit register.
Other cases of CMP in inline asm have had their constraints checked, and
appear to all be fine.
Fixes: 6006c0d8ce ("metag: Atomics, locks and bitops")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-metag@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b2e1c26f0b upstream.
glibc recently did a sync up (94e73c95d9b5 "elf.h: Sync with the gabi
webpage") that added a #define for EM_METAG but did not add relocations
This triggers build errors:
scripts/recordmcount.c: In function 'do_file':
scripts/recordmcount.c:466:28: error: 'R_METAG_ADDR32' undeclared (first use in this function)
case EM_METAG: reltype = R_METAG_ADDR32;
^~~~~~~~~~~~~~
scripts/recordmcount.c:466:28: note: each undeclared identifier is reported only once for each function it appears in
scripts/recordmcount.c:468:20: error: 'R_METAG_NONE' undeclared (first use in this function)
rel_type_nop = R_METAG_NONE;
^~~~~~~~~~~~
Work around this change with some more #ifdefery for the relocations.
Fedora Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1354034
Link: http://lkml.kernel.org/r/1468005530-14757-1-git-send-email-labbott@redhat.com
Cc: James Hogan <james.hogan@imgtec.com>
Fixes: 00512bdd45 ("metag: ftrace support")
Reported-by: Ross Burton <ross.burton@intel.com>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 37cf99e08c upstream.
The balloon has a special mechanism that is subscribed to the oom
notification which leads to deflation for a fixed number of pages.
The number is always fixed even when the balloon is fully deflated.
But leak_balloon did not expect that the pages to deflate will be more
than taken, and raise a "BUG" in balloon_page_dequeue when page list
will be empty.
So, the simplest solution would be to check that the number of releases
pages is less or equal to the number taken pages.
Signed-off-by: Konstantin Neumoin <kneumoin@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 196f954e25 upstream.
This reverts commit 013dd9e038
("drm/i915/dp: fall back to 18 bpp when sink capability is unknown")
This commit introduced a regression into stable kernels,
as it reduces output color depth to 6 bpc for any video
sink connected to a Displayport connector if that sink
doesn't report a specific color depth via EDID, or if
our EDID parser doesn't actually recognize the proper
bpc from EDID.
Affected are active DisplayPort->VGA converters and
active DisplayPort->DVI converters. Both should be
able to handle 8 bpc, but are degraded to 6 bpc with
this patch.
The reverted commit was meant to fix
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=105331
A followup patch implements a fix for that specific bug,
which is caused by a faulty EDID of the affected DP panel
by adding a new EDID quirk for that panel.
DP 18 bpp fallback handling and other improvements to
DP sink bpc detection will be handled for future
kernels in a separate series of patches.
Please backport to stable.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e10aec652f upstream.
Bugzilla https://bugzilla.kernel.org/show_bug.cgi?id=105331
reports that the "AEO model 0" display is driven with 8 bpc
without dithering by default, which looks bad because that
panel is apparently a 6 bpc DP panel with faulty EDID.
A fix for this was made by commit 013dd9e038
("drm/i915/dp: fall back to 18 bpp when sink capability is unknown").
That commit triggers new regressions in precision for DP->DVI and
DP->VGA displays. A patch is out to revert that commit, but it will
revert video output for the AEO model 0 panel to 8 bpc without
dithering.
The EDID 1.3 of that panel, as decoded from the xrandr output
attached to that bugzilla bug report, is somewhat faulty, and beyond
other problems also sets the "DFP 1.x compliant TMDS" bit, which
according to DFP spec means to drive the panel with 8 bpc and
no dithering in absence of other colorimetry information.
Try to make the original bug reporter happy despite the
faulty EDID by adding a quirk to mark that panel as 6 bpc,
so 6 bpc output with dithering creates a nice picture.
Tested by injecting the edid from the fdo bug into a DP connector
via drm_kms_helper.edid_firmware and verifying the 6 bpc + dithering
is selected.
This patch should be backported to stable.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a1f5524a66 upstream.
Restore the correct behaviour (as in check msg.reply) when aux
->transfer() returns 0. It got removed in
commit 82922da391 ("drm/dp_helper: Retry aux transactions on all errors")
Now I can actually dump the "entire" DPCD on a Dell UP2314Q with
ddrescue. It has some offsets in the DPCD that can't be read
for some resaon, all you get is defers. Previously ddrescue would
just give up at the first unredable offset on account of
read() returning 0 means EOF. Here's the ddrescue log
for the interested:
0x00000000 0x00001400 +
0x00001400 0x00000030 -
0x00001430 0x000001D0 +
0x00001600 0x00000030 -
0x00001630 0x0001F9D0 +
0x00021000 0x00000001 -
0x00021001 0x000DEFFF +
Cc: Lyude <cpaul@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch
Fixes: 82922da391 ("drm/dp_helper: Retry aux transactions on all errors")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc0b408f5a upstream.
Because we are using a custom crtc_state structure, we must override the
reset helper to allocate the correct amount of memory.
Fixes: 4e257d9eee ("drm/rockchip: get rid of rockchip_drm_crtc_mode_config")
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7f1052a8fa upstream.
Update CDCLK_FREQ on BDW after changing the cdclk frequency. Not sure
if this is a late addition to the spec, or if I simply overlooked this
step when writing the original code.
This is what Bspec has to say about CDCLK_FREQ:
"Program this field to the CD clock frequency minus one. This is used to
generate a divided down clock for miscellaneous timers in display."
And the "Broadwell Sequences for Changing CD Clock Frequency" section
clarifies this further:
"For CD clock 337.5 MHz, program 337 decimal.
For CD clock 450 MHz, program 449 decimal.
For CD clock 540 MHz, program 539 decimal.
For CD clock 675 MHz, program 674 decimal."
Cc: Mika Kahola <mika.kahola@intel.com>
Fixes: b432e5cfd5 ("drm/i915: BDW clock change support")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461689194-6079-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 28668f43b8 upstream.
The patch f045f459d9 ("drm/nouveau/fbcon: fix out-of-bounds memory accesses")
tries to fix some out of memory accesses. Unfortunatelly, the patch breaks the
display when using fonts with width that is not divisiable by 8.
The monochrome bitmap for each character is stored in memory by lines from top
to bottom. Each line is padded to a full byte.
For example, for 22x11 font, each line is padded to 16 bits, so each
character is consuming 44 bytes total, that is 11 32-bit words. The patch
f045f459d9 changed the logic to "dsize = ALIGN(image->width *
image->height, 32) >> 5", that is just 8 words - this is incorrect and it
causes display corruption.
This patch adds the necesary padding of lines to 8 bytes.
This patch should be backported to stable kernels where f045f459d9 was
backported.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Fixes: f045f459d9 ("drm/nouveau/fbcon: fix out-of-bounds memory accesses")
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 14ff8d48f2 upstream.
DRM_CONNECTOR_POLL_CONNECT only enables polling for connections, not
disconnections. Because of this, we end up losing hotplug polling for
analog connectors once they get connected.
Easy way to reproduce:
- Grab a machine with a radeon GPU and a VGA port
- Plug a monitor into the VGA port, wait for it to update the connector
from disconnected to connected
- Disconnect the monitor on VGA, a hotplug event is never sent for the
removal of the connector.
Originally, only using DRM_CONNECTOR_POLL_CONNECT might have been a good
idea since doing VGA polling can sometimes result in having to mess with
the DAC voltages to figure out whether or not there's actually something
there since VGA doesn't have HPD. Doing this would have the potential of
showing visible artifacts on the screen every time we ran a poll while a
VGA display was connected. Luckily, radeon_vga_detect() only resorts to
this sort of polling if the poll is forced, and DRM's polling helper
doesn't force it's polls.
Additionally, this removes some assignments to connector->polled that
weren't actually doing anything.
Signed-off-by: Lyude <cpaul@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8a04c994d upstream.
Some of the checks didn't handle frev 2 tables properly.
amdgpu doesn't support any tables pre-frev 2, so drop
the checks.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23a1a9e54e upstream.
Just about all of amdgpu's connector probing functions try to acquire
runtime PM refs. If we try to do this in the context of
amdgpu_resume_kms by calling drm_helper_hpd_irq_event(), we end up
deadlocking the system.
Since we're guaranteed to be holding the spinlock for RPM in
amdgpu_resume_kms, and we already know the GPU is in working order, we
need to prevent the RPM helpers from trying to run during the initial
connector reprobe on resume.
There's a couple of solutions I've explored for fixing this, but this
one by far seems to be the simplest and most reliable (plus I'm pretty
sure that's what disable_depth is there for anyway).
Reproduction recipe:
- Get any laptop dual GPUs using PRIME
- Make sure runtime PM is enabled for amdgpu
- Boot the machine
- If the machine managed to boot without hanging, switch out of X to
another VT. This should definitely cause X to hang infinitely.
Changes since v1:
- add appropriate #ifdef checks for CONFIG_PM. This is not very
useful, but it appears some kernel test suites test compiling amdgpu
with CONFIG_PM disabled, which results in this patch breaking the builds
if we don't include this #ifdef
Cc: Alex Deucher <alexdeucher@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Lyude <cpaul@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b636a1b3d6 upstream.
DRM_CONNECTOR_POLL_CONNECT only enables polling for connections, not
disconnections. Because of this, we end up losing hotplug polling for
analog connectors once they get connected.
Easy way to reproduce:
- Grab a machine with an AMD GPU and a VGA port
- Plug a monitor into the VGA port, wait for it to update the connector
from disconnected to connected
- Disconnect the monitor on VGA, a hotplug event is never sent for the
removal of the connector.
Originally, only using DRM_CONNECTOR_POLL_CONNECT might have been a good
idea since doing VGA polling can sometimes result in having to mess with
the DAC voltages to figure out whether or not there's actually something
there since VGA doesn't have HPD. Doing this would have the potential of
showing visible artifacts on the screen every time we ran a poll while a
VGA display was connected. Luckily, amdgpu_vga_detect() only resorts to
this sort of polling if the poll is forced, and DRM's polling helper
doesn't force it's polls.
Additionally, this removes some assignments to connector->polled that
weren't actually doing anything.
Signed-off-by: Lyude <cpaul@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ecfaf0c42f upstream.
Commit e93762bbf6 ("w1: masters: omap_hdq: add support for 1-wire
mode") added a statement to clear the hdq_irqstatus flags in
hdq_read_byte().
If the hdq reading process is scheduled slowly or interrupts are
disabled for a while the hardware read activity might already be
finished on entry of hdq_read_byte(). And hdq_isr() already has set the
hdq_irqstatus to 0x6 (can be seen in debug mode) denoting that both, the
TXCOMPLETE and RXCOMPLETE interrupts occurred in parallel.
This means there is no need to wait and the hdq_read_byte() can just
read the byte from the hdq controller.
By resetting hdq_irqstatus to 0 the read process is forced to be always
waiting again (because the if statement always succeeds) but the
hardware will not issue another RXCOMPLETE interrupt. This results in a
false timeout.
After such a situation the hdq bus hangs.
Link: http://lkml.kernel.org/r/b724765f87ad276a69625bc19806c8c8844c4590.1469513669.git.hns@goldelico.com
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0e0e367740 upstream.
It seems risky to always rely on the caller to ensure the socket's
address family is correct before passing it to the NetLabel kAPI,
especially since we see at least one LSM which didn't. Add address
family checks to the *_delattr() functions to help prevent future
problems.
Reported-by: Maninder Singh <maninder1.s@samsung.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 63af8e44ea upstream.
The valid_entries index should not be incremented until after we have
acquired the pointer to the value, or we will read and write data one
item off.
Fixes: 50e9964141 ("soc: qcom: smp2p: Qualcomm Shared Memory Point to Point")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 726a4994b0 upstream.
Unprivileged users can't use hierarchies if they create them as they do not
have privilieges to the root directory.
Which means the only thing a hiearchy created by an unprivileged user
is good for is expanding the number of cgroup links in every css_set,
which is a DOS attack.
We could allow hierarchies to be created in namespaces in the initial
user namespace. Unfortunately there is only a single namespace for
the names of heirarchies, so that is likely to create more confusion
than not.
So do the simple thing and restrict hiearchy creation to the initial
cgroup namespace.
Fixes: a79a908fd2 ("cgroup: introduce cgroup namespaces")
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eedd0f4cbf upstream.
In most code paths involving cgroup migration cgroup_threadgroup_rwsem
is taken. There are two exceptions:
- remove_tasks_in_empty_cpuset calls cgroup_transfer_tasks
- vhost_attach_cgroups_work calls cgroup_attach_task_all
With cgroup_threadgroup_rwsem held it is guaranteed that cgroup_post_fork
and copy_cgroup_ns will reference the same css_set from the process calling
fork.
Without such an interlock there process after fork could reference one
css_set from it's new cgroup namespace and another css_set from
task->cgroups, which semantically is nonsensical.
Fixes: a79a908fd2 ("cgroup: introduce cgroup namespaces")
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7bd8830875 upstream.
If "clone(CLONE_NEWCGROUP...)" is called it results in a nice lockdep
valid splat.
In __cgroup_proc_write the lock ordering is:
cgroup_mutex -- through cgroup_kn_lock_live
cgroup_threadgroup_rwsem
In copy_process the guts of clone the lock ordering is:
cgroup_threadgroup_rwsem -- through threadgroup_change_begin
cgroup_mutex -- through copy_namespaces -- copy_cgroup_ns
lockdep reports some a different call chains for the first ordering of
cgroup_mutex and cgroup_threadgroup_rwsem but it is harder to trace.
This is most definitely deadlock potential under the right
circumstances.
Fix this by by skipping the cgroup_mutex and making the locking in
copy_cgroup_ns mirror the locking in cgroup_post_fork which also runs
during fork under the cgroup_threadgroup_rwsem.
Fixes: a79a908fd2 ("cgroup: introduce cgroup namespaces")
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a376ac11f upstream.
The patch that this was preparing for made it into neither v4.7 nor
v4.8, so we should back this out as well to avoid the opposite
warning:
arch/arm/configs/aspeed_g5_defconfig:62:warning: symbol value '1' invalid for PRINTK_TIME
arch/arm/configs/aspeed_g4_defconfig:61:warning: symbol value '1' invalid for PRINTK_TIME
Sorry for not catching this earlier.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 0ef659a300 ("ARM: aspeed: adapt defconfigs for new CONFIG_PRINTK_TIME")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5c86b7496 upstream.
c90bb7b enabled the high speed UARTs of the Jetson TK1. Due to a merge
quirk, wrong addresses were introduced. Fix it and use the correct
addresses.
Thierry let me know, that there is another patch (b5896f67ab in
linux-next) in preparation which removes all the '0,' prefixes of unit
addresses on Tegra124 and is planned to go upstream in 4.8, so
this patch will get reverted then.
But for the moment, this patch is necessary to fix current misbehaviour.
Fixes: c90bb7b9b9 ("ARM: tegra: Add high speed UARTs to Jetson TK1 device tree")
Signed-off-by: Ralf Ramsauer <ralf@ramses-pyramidenbau.de>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a20303725e upstream.
Clearly QEMU is very permissive in how its PL310 model may be set up,
but the real hardware turns out to be far more particular about things
actually being correct. Fix up the DT description so that the real
thing actually boots:
- The arm,data-latency and arm,tag-latency properties need 3 cells to
be valid, otherwise we end up retaining the default 8-cycle latencies
which leads pretty quickly to lockup.
- The arm,dirty-latency property is only relevant to L210/L220, so get
rid of it.
- The cache geometry override also leads to lockup and/or general
misbehaviour. Irritatingly, the manual doesn't state the actual PL310
configuration, but based on the boardfile code and poking registers
from the Boot Monitor, it would seem to be 8 sets of 16KB ways.
With that, we can successfully boot to enjoy the fun of mismatched FPUs...
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc51b632c7 upstream.
It seems that recent kernels have a shorter timeout when scanning for
ethernet phys causing us to hit a timeout on boards where the phy's
regulator gets enabled just before scanning, which leads to non working
ethernet.
A 10ms startup delay seems to be enough to fix it, this commit adds a
20ms startup delay just to be safe.
This has been tested on a sun4i-a10-a1000 and sun5i-a10s-wobo-i5 board,
both of which have non-working ethernet on recent kernels without this
fix.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f127089650 upstream.
When a L2 cache controller is used in a system that provides hardware
coherency, the entire outer cache operations are useless, and can be
skipped. Moreover, on some systems, it is harmful as it causes
deadlocks between the Marvell coherency mechanism, the Marvell PCIe
controller and the Cortex-A9.
In the current kernel implementation, the outer cache flush range
operation is triggered by the dma_alloc function.
This operation can be take place during runtime and in some
circumstances may lead to the PCIe/PL310 deadlock on Armada 375/38x
SoCs.
This patch extends the __dma_clear_buffer() function to receive a
boolean argument related to the coherency of the system. The same
things is done for the calling functions.
Reported-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 43761473c2 upstream.
There is a double fetch problem in audit_log_single_execve_arg()
where we first check the execve(2) argumnets for any "bad" characters
which would require hex encoding and then re-fetch the arguments for
logging in the audit record[1]. Of course this leaves a window of
opportunity for an unsavory application to munge with the data.
This patch reworks things by only fetching the argument data once[2]
into a buffer where it is scanned and logged into the audit
records(s). In addition to fixing the double fetch, this patch
improves on the original code in a few other ways: better handling
of large arguments which require encoding, stricter record length
checking, and some performance improvements (completely unverified,
but we got rid of some strlen() calls, that's got to be a good
thing).
As part of the development of this patch, I've also created a basic
regression test for the audit-testsuite, the test can be tracked on
GitHub at the following link:
* https://github.com/linux-audit/audit-testsuite/issues/25
[1] If you pay careful attention, there is actually a triple fetch
problem due to a strnlen_user() call at the top of the function.
[2] This is a tiny white lie, we do make a call to strnlen_user()
prior to fetching the argument data. I don't like it, but due to the
way the audit record is structured we really have no choice unless we
copy the entire argument at once (which would require a rather
wasteful allocation). The good news is that with this patch the
kernel no longer relies on this strnlen_user() value for anything
beyond recording it in the log, we also update it with a trustworthy
value whenever possible.
Reported-by: Pengfei Wang <wpengfeinudt@gmail.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3254de6bf7 upstream.
Not doing so might cause IO-Page-Faults when a device uses
an alias request-id and the alias-dte is left in a lower
page-mode which does not cover the address allocated from
the iova-allocator.
Fixes: 492667dacc ('x86/amd-iommu: Remove amd_iommu_pd_table')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b548e786ce upstream.
The default domain for a device might also be
identity-mapped. In this case the kernel would crash when
unity mappings are defined for the device. Fix that by
making sure the domain is a dma_ops domain.
Fixes: 0bb6e243d7 ('iommu/amd: Support IOMMU_DOMAIN_DMA type allocation')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cda7005ba2 upstream.
This domain type is not yet handled in the
iommu_ops->domain_free() call-back. Fix that.
Fixes: 0bb6e243d7 ('iommu/amd: Support IOMMU_DOMAIN_DMA type allocation')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c6d90e2bb upstream.
The implementation of iova_to_phys for the long-descriptor ARM
io-pgtable code always masks with the granule size when inserting the
low virtual address bits into the physical address determined from the
page tables. In cases where the leaf entry is found before the final
level of table (i.e. due to a block mapping), this results in rounding
down to the bottom page of the block mapping. Consequently, the physical
address range batching in the vfio_unmap_unpin is defeated and we end
up taking the long way home.
This patch fixes the problem by masking the virtual address with the
appropriate mask for the level at which the leaf descriptor is located.
The short-descriptor code already gets this right, so no change is
needed there.
Reported-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c365d18a7 upstream.
In 'commit <55d940430ab9> ("iommu/vt-d: Get rid of domain->iommu_lock")',
the error handling path is changed a little, which makes the function
always return 0.
This path fixes this.
Signed-off-by: Wei Yang <richard.weiyang@gmail.com>
Fixes: 55d940430a ('iommu/vt-d: Get rid of domain->iommu_lock')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b54b874fba upstream.
Removal of IOMMU driver cannot be done reliably, so Exynos IOMMU driver
doesn't support this operation. It is essential for system operation, so
it makes sense to prevent unbinding by disabling bind/unbind sysfs
feature for SYSMMU controller driver to avoid kernel ops or trashing
memory caused by such operation.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 783011b130 upstream.
unicore32 fails to compile with the following errors.
mm/memory.c: In function ‘__handle_mm_fault’:
mm/memory.c:3381: error:
too many arguments to function ‘arch_vma_access_permitted’
mm/gup.c: In function ‘check_vma_flags’:
mm/gup.c:456: error:
too many arguments to function ‘arch_vma_access_permitted’
mm/gup.c: In function ‘vma_permits_fault’:
mm/gup.c:640: error:
too many arguments to function ‘arch_vma_access_permitted’
Fixes: d61172b4b6 ("mm/core, x86/mm/pkeys: Differentiate instruction fetches")
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f7db0b2838 upstream.
We want to recover the open stateid if there is no layout stateid
and/or the stateid argument matches an open stateid.
Otherwise throw out the existing layout and recover from scratch, as
the layout stateid is bad.
Fixes: 183d9e7b11 ("pnfs: rework LAYOUTGET retry handling")
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66b53f3258 upstream.
Instead of giving up altogether and falling back to doing I/O
through the MDS, which may make the situation worse, wait for
2 lease periods for the callback to resolve itself, and then
try destroying the existing layout.
Only if this was an attempt at getting a first layout, do we
give up altogether, as the server is clearly crazy.
Fixes: 183d9e7b11 ("pnfs: rework LAYOUTGET retry handling")
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 56b38a1f7c upstream.
The non-retry error path is currently broken and ends up releasing the
reference to the layout twice. It also can end up clearing the
NFS_LAYOUT_FIRST_LAYOUTGET flag twice, causing a race.
In addition, the retry path will fail to decrement the plh_outstanding
counter.
Fixes: 183d9e7b11 ("pnfs: rework LAYOUTGET retry handling")
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd257933fa upstream.
nfsd4_lock will take the st_mutex before working with the stateid it
gets, but between the time when we drop the cl_lock and take the mutex,
the stateid could become unhashed (a'la FREE_STATEID). If that happens
the lock stateid returned to the client will be forgotten.
Fix this by first moving the st_mutex acquisition into
lookup_or_create_lock_state. Then, have it check to see if the lock
stateid is still hashed after taking the mutex. If it's not, then put
the stateid and try the find/create again.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Tested-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 42691398be upstream.
When running LTP's nfslock01 test, the Linux client can send a LOCK
and a FREE_STATEID request at the same time. The outcome is:
Frame 324 R OPEN stateid [2,O]
Frame 115004 C LOCK lockowner_is_new stateid [2,O] offset 672000 len 64
Frame 115008 R LOCK stateid [1,L]
Frame 115012 C WRITE stateid [0,L] offset 672000 len 64
Frame 115016 R WRITE NFS4_OK
Frame 115019 C LOCKU stateid [1,L] offset 672000 len 64
Frame 115022 R LOCKU NFS4_OK
Frame 115025 C FREE_STATEID stateid [2,L]
Frame 115026 C LOCK lockowner_is_new stateid [2,O] offset 672128 len 64
Frame 115029 R FREE_STATEID NFS4_OK
Frame 115030 R LOCK stateid [3,L]
Frame 115034 C WRITE stateid [0,L] offset 672128 len 64
Frame 115038 R WRITE NFS4ERR_BAD_STATEID
In other words, the server returns stateid L in a successful LOCK
reply, but it has already released it. Subsequent uses of stateid L
fail.
To address this, protect the generation check in nfsd4_free_stateid
with the st_mutex. This should guarantee that only one of two
outcomes occurs: either LOCK returns a fresh valid stateid, or
FREE_STATEID returns NFS4ERR_LOCKS_HELD.
Reported-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Fix-suggested-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 149a4fddd0 upstream.
NFS doesn't expect requests with wb_bytes set to zero and may make
unexpected decisions about how to handle that request at the page IO layer.
Skip request creation if we won't have any wb_bytes in the request.
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Reviewed-by: Weston Andros Adamson <dros@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b8b08cbfb upstream.
Commit 56244ef151 was almost but not quite enough to fix the
reservation math after btrfs_copy_from_user returned partial copies.
Some users are still seeing warnings in btrfs_destroy_inode, and with a
long enough test run I'm able to trigger them as well.
This patch fixes the accounting math again, bringing it much closer to
the way it was before the sectorsize conversion Chandan did. The
problem is accounting for the offset into the page/sector when we do a
partial copy. This one just uses the dirty_sectors variable which
should already be updated properly.
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6bcb80143e upstream.
At the start of __tm_recheckpoint() we save the kernel stack pointer
(r1) in SPRG SCRATCH0 (SPRG2) so that we can restore it after the
trecheckpoint.
Unfortunately, the same SPRG is used in the SLB miss handler. If an
SLB miss is taken between the save and restore of r1 to the SPRG, the
SPRG is changed and hence r1 is also corrupted. We can end up with
the following crash when we start using r1 again after the restore
from the SPRG:
Oops: Bad kernel stack pointer, sig: 6 [#1]
SMP NR_CPUS=2048 NUMA pSeries
CPU: 658 PID: 143777 Comm: htm_demo Tainted: G EL X 4.4.13-0-default #1
task: c0000b56993a7810 ti: c00000000cfec000 task.ti: c0000b56993bc000
NIP: c00000000004f188 LR: 00000000100040b8 CTR: 0000000010002570
REGS: c00000000cfefd40 TRAP: 0300 Tainted: G EL X (4.4.13-0-default)
MSR: 8000000300001033 <SF,ME,IR,DR,RI,LE> CR: 02000424 XER: 20000000
CFAR: c000000000008468 DAR: 00003ffd84e66880 DSISR: 40000000 SOFTE: 0
PACATMSCRATCH: 00003ffbc865e680
GPR00: fffffffcfabc4268 00003ffd84e667a0 00000000100d8c38 000000030544bb80
GPR04: 0000000000000002 00000000100cf200 0000000000000449 00000000100cf100
GPR08: 000000000000c350 0000000000002569 0000000000002569 00000000100d6c30
GPR12: 00000000100d6c28 c00000000e6a6b00 00003ffd84660000 0000000000000000
GPR16: 0000000000000003 0000000000000449 0000000010002570 0000010009684f20
GPR20: 0000000000800000 00003ffd84e5f110 00003ffd84e5f7a0 00000000100d0f40
GPR24: 0000000000000000 0000000000000000 0000000000000000 00003ffff0673f50
GPR28: 00003ffd84e5e960 00000000003d0f00 00003ffd84e667a0 00003ffd84e5e680
NIP [c00000000004f188] restore_gprs+0x110/0x17c
LR [00000000100040b8] 0x100040b8
Call Trace:
Instruction dump:
f8a1fff0 e8e700a8 38a00000 7ca10164 e8a1fff8 e821fff0 7c0007dd 7c421378
7db142a6 7c3242a6 38800002 7c810164 <e9c100e0> e9e100e8 ea0100f0 ea2100f8
We hit this on large memory machines (> 2TB) but it can also be hit on
smaller machines when 1TB segments are disabled.
To hit this, you also need to be virtualised to ensure SLBs are
periodically removed by the hypervisor.
This patches moves the saving of r1 to the SPRG to the region where we
are guaranteed not to take any further SLB misses.
Fixes: 98ae22e15b ("powerpc: Add helper functions for transactional memory context switching")
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b731bcfde upstream.
Propagate errors from kvm_mips_handle_kseg0_tlb_fault() and
kvm_mips_handle_mapped_seg_tlb_fault(), usually triggering an internal
error since they normally indicate the guest accessed bad physical
memory or the commpage in an unexpected way.
Fixes: 858dd5d457 ("KVM/MIPS32: MMU/TLB operations for the Guest.")
Fixes: e685c689f3 ("KVM/MIPS32: Privileged instruction/target branch emulation.")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: <stable@vger.kernel.org> # 3.10.x-
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
[james.hogan@imgtec.com: Backport to v4.7]
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8985d50382 upstream.
kvm_mips_handle_mapped_seg_tlb_fault() calculates the guest frame number
based on the guest TLB EntryLo values, however it is not range checked
to ensure it lies within the guest_pmap. If the physical memory the
guest refers to is out of range then dump the guest TLB and emit an
internal error.
Fixes: 858dd5d457 ("KVM/MIPS32: MMU/TLB operations for the Guest.")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: <stable@vger.kernel.org> # 3.10.x-
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
[james.hogan@imgtec.com: Backport to v4.7]
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c604cffa93 upstream.
kvm_mips_handle_mapped_seg_tlb_fault() appears to map the guest page at
virtual address 0 to PFN 0 if the guest has created its own mapping
there. The intention is unclear, but it may have been an attempt to
protect the zero page from being mapped to anything but the comm page in
code paths you wouldn't expect from genuine commpage accesses (guest
kernel mode cache instructions on that address, hitting trapping
instructions when executing from that address with a coincidental TLB
eviction during the KVM handling, and guest user mode accesses to that
address).
Fix this to check for mappings exactly at KVM_GUEST_COMMPAGE_ADDR (it
may not be at address 0 since commit 42aa12e74e ("MIPS: KVM: Move
commpage so 0x0 is unmapped")), and set the corresponding EntryLo to be
interpreted as 0 (invalid).
Fixes: 858dd5d457 ("KVM/MIPS32: MMU/TLB operations for the Guest.")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: <stable@vger.kernel.org> # 3.10.x-
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
[james.hogan@imgtec.com: Backport to v4.7]
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b4d008787 upstream.
Since systemd is consistently using /dev/urandom before it is
initialized, we can't see the other potentially dangerous users of
/dev/urandom immediately after boot. So print the first ten such
complaints instead.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3371f3da08 upstream.
If we have a hardware RNG and are using the in-kernel rngd, we should
use this to initialize the non-blocking pool so that getrandom(2)
doesn't block unnecessarily.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b1132deac0 upstream.
get_random_long() reads from the get_random_int_hash array using an
unsigned long pointer. For this code to be guaranteed correct on all
architectures, the array must be aligned to an unsigned long boundary.
Signed-off-by: Eric Biggers <ebiggers3@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4b44f2d18a upstream.
The Hyper-V Linux Integration Services use the VMBus implementation for
communication with the Hypervisor. VMBus registers its own interrupt
handler that completely bypasses the common Linux interrupt handling.
This implies that the interrupt entropy collector is not triggered.
This patch adds the interrupt entropy collection callback into the VMBus
interrupt handler function.
Signed-off-by: Stephan Mueller <stephan.mueller@atsec.com>
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7893242e24 upstream.
During following a symbolic link we received err_buf from SMB2_open().
While the validity of SMB2 error response is checked previously
in smb2_check_message() a symbolic link payload is not checked at all.
Fix it by adding such checks.
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Pavel Shilovsky <pshilovsky@samba.org>
Signed-off-by: Steve French <smfrench@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd975d1eea upstream.
The secmech hmac(md5) structures are present in the TCP_Server_Info
struct and can be shared among multiple CIFS sessions. However, the
server mutex is not currently held when these structures are allocated
and used, which can lead to a kernel crashes, as in the scenario below:
mount.cifs(8) #1 mount.cifs(8) #2
Is secmech.sdeschmaccmd5 allocated?
// false
Is secmech.sdeschmaccmd5 allocated?
// false
secmech.hmacmd = crypto_alloc_shash..
secmech.sdeschmaccmd5 = kzalloc..
sdeschmaccmd5->shash.tfm = &secmec.hmacmd;
secmech.sdeschmaccmd5 = kzalloc
// sdeschmaccmd5->shash.tfm
// not yet assigned
crypto_shash_update()
deref NULL sdeschmaccmd5->shash.tfm
Unable to handle kernel paging request at virtual address 00000030
epc : 8027ba34 crypto_shash_update+0x38/0x158
ra : 8020f2e8 setup_ntlmv2_rsp+0x4bc/0xa84
Call Trace:
crypto_shash_update+0x38/0x158
setup_ntlmv2_rsp+0x4bc/0xa84
build_ntlmssp_auth_blob+0xbc/0x34c
sess_auth_rawntlmssp_authenticate+0xac/0x248
CIFS_SessSetup+0xf0/0x178
cifs_setup_session+0x4c/0x84
cifs_get_smb_ses+0x2c8/0x314
cifs_mount+0x38c/0x76c
cifs_do_mount+0x98/0x440
mount_fs+0x20/0xc0
vfs_kern_mount+0x58/0x138
do_mount+0x1e8/0xccc
SyS_mount+0x88/0xd4
syscall_common+0x30/0x54
Fix this by locking the srv_mutex around the code which uses these
hmac(md5) structures. All the other secmech algos already have similar
locking.
Fixes: 95dc8dd14e ("Limit allocation of crypto mechanisms to dialect which requires")
Signed-off-by: Rabin Vincent <rabinv@axis.com>
Acked-by: Sachin Prabhu <sprabhu@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b782fcc1cb upstream.
adfeb3e0 ("cifs: Make echo interval tunable") added a comparison of
vol->echo_interval to server->echo_interval as a criterium to
match_server(), but:
(1) A default value is set for server->echo_interval but not for
vol->echo_interval, meaning these can never match if the echo_interval
option is not specified.
(2) vol->echo_interval is in seconds but server->echo_interval is in
jiffies, meaning these can never match even if the echo_interval option
is specified.
This broke TCP session reuse since match_server() can never return 1.
Fix it.
Fixes: adfeb3e0 ("cifs: Make echo interval tunable")
Signed-off-by: Rabin Vincent <rabinv@axis.com>
Acked-by: Sachin Prabhu <sprabhu@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d9535b6ef upstream.
When opening a file with O_CREAT flag, check to see if the file opened
is an existing directory.
This prevents the directory from being opened which subsequently causes
a crash when the close function for directories cifs_closedir() is called
which frees up the file->private_data memory while the file is still
listed on the open file list for the tcon.
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Reported-by: Xiaoli Feng <xifeng@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a6b5058faf upstream.
if, when mounting //HOST/share/sub/dir/foo we can query /sub/dir/foo but
not any of the path components above:
- store the /sub/dir/foo prefix in the cifs super_block info
- in the superblock, set root dentry to the subpath dentry (instead of
the share root)
- set a flag in the superblock to remember it
- use prefixpath when building path from a dentry
fixes bso#8950
Signed-off-by: Aurelien Aptel <aaptel@suse.com>
Reviewed-by: Pavel Shilovsky <pshilovsky@samba.org>
Signed-off-by: Steve French <smfrench@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit abcfb5d979 upstream.
The jbd2 journal stores the commit time in 64-bit seconds and 32-bit
nanoseconds, which avoids an overflow in 2038, but it gets the numbers
from current_kernel_time(), which uses 'long' seconds on 32-bit
architectures.
This simply changes the code to call current_kernel_time64() so
we use 64-bit seconds consistently.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b4dff28740 upstream.
page should be calculated using physical address.
If platform uses non-trivial dma-to-phys memory translation,
dma_handle should be converted to physicval address before
calculation of page.
Failing to do so results in struct page * pointing to
wrong or non-existent memory.
Fixes: f2e3d55397 ("ARC: dma: reintroduce platform specific dma<->phys")
Signed-off-by: Vladimir Kondratiev <vladimir.kondratiev@intel.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3925a16ae9 upstream.
LTP madvise05 was generating mm splat
| [ARCLinux]# /sd/ltp/testcases/bin/madvise05
| BUG: Bad page map in process madvise05 pte:80e08211 pmd:9f7d4000
| page:9fdcfc90 count:1 mapcount:-1 mapping: (null) index:0x0 flags: 0x404(referenced|reserved)
| page dumped because: bad pte
| addr:200b8000 vm_flags:00000070 anon_vma: (null) mapping: (null) index:1005c
| file: (null) fault: (null) mmap: (null) readpage: (null)
| CPU: 2 PID: 6707 Comm: madvise05
And for newer kernels, the system was rendered unusable afterwards.
The problem was mprotect->pte_modify() clearing PTE_SPECIAL (which is
set to identify the special zero page wired to the pte).
When pte was finally unmapped, special casing for zero page was not
done, and instead it was treated as a "normal" page, tripping on the
map counts etc.
This fixes ARC STAR 9001053308
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d2e12e66a9 upstream.
rproc_add adds the newly created remoteproc to a list for use by
rproc_get_by_phandle and then does some additional processing to finish
adding the remoteproc. This leaves a small window of time in which the
rproc is available in the list but not yet fully initialized, so if
another driver comes along and gets a handle to the rproc, it will be
invalid. Rearrange the code in rproc_add to make sure the rproc is added
to the list only after it has been successfuly initialized.
Fixes: fec47d8635 ("remoteproc: introduce rproc_get_by_phandle API")
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 76bc8e2843 upstream.
This does not work and does not make sense. So instead of fixing it
(probably not hard) just disallow.
Reported-by: Andrei Vagin <avagin@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67f8ecc550 upstream.
Many devices use userspace bluetooth stacks like BlueZ or Bluedroid in combination
with uhid. If any of these stacks is used with a HID device for which the driver
performs a HID request as part .probe (or technically another HID operation),
this results in a deadlock situation. The deadlock results in a 5 second timeout
for I/O operations in HID drivers, so isn't fatal, but none of the I/O operations
have a chance of succeeding.
The root cause for the problem is that uhid only allows for one request to be
processed at a time per uhid instance and locks out other operations. This means
that if a user space is creating a new HID device through 'UHID_CREATE', which
ultimately triggers '.probe' through the HID layer. Then any HID request e.g. a
read for calibration data would trigger a HID operation on uhid again, but it
won't go out to userspace, because it is still stuck in UHID_CREATE.
In addition bluetooth stacks are typically single threaded, so they wouldn't be
able to handle any requests while waiting on uhid.
Lucikly the UHID spec is somewhat flexible and allows for fixing the issue,
without breaking user space. The idea which the patch implements as discussed
with David Herrmann is to decouple adding of a hid device (which triggers .probe)
from UHID_CREATE. The work will kick off roughly once UHID_CREATE completed (or
else will wait a tiny bit of time in .probe for a lock). A HID driver has to call
HID to call 'hid_hw_start()' as part of .probe once it is ready for I/O, which
triggers UHID_START to user space. Any HID operations should function now within
.probe and won't deadlock because userspace is stuck on UHID_CREATE.
We verified this patch on Bluedroid with Android 6.0 and on desktop Linux with
BlueZ stacks. Prior to the patch they had the deadlock issue.
[jkosina@suse.cz: reword subject]
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d9083160c2 upstream.
There was an issue reported by Lucz Geza on Dell Perc 6i. As per issue
reported, megaraid_sas driver goes into an infinite error reporting loop
as soon as there is a change in the status of one of the
arrays (degrade, resync online etc ). Below are the error logs reported
continuously-
Jun 25 08:49:30 ns8 kernel: [ 757.757017] megaraid_sas 0000:02:00.0: DCMD failed/not supported by firmware: megasas_get_pd_list 4115
Jun 25 08:49:30 ns8 kernel: [ 757.778017] megaraid_sas 0000:02:00.0: DCMD failed/not supported by firmware: megasas_get_pd_list 4115
Jun 25 08:49:30 ns8 kernel: [ 757.799017] megaraid_sas 0000:02:00.0: DCMD failed/not supported by firmware: megasas_get_pd_list 4115
Jun 25 08:49:30 ns8 kernel: [ 757.820018] megaraid_sas 0000:02:00.0: DCMD failed/not supported by firmware: megasas_get_pd_list 4115
Jun 25 08:49:30 ns8 kernel: [ 757.841018] megaraid_sas 0000:02:00.0: DCMD failed/not supported by firmware: megasas_get_pd_list 4115
This issue is very much specific to controllers which do not support
DCMD- MR_DCMD_PD_LIST_QUERY. In case of any hotplugging/rescanning of
drives, AEN thread will be scheduled by driver and fire DCMD-
MR_DCMD_PD_LIST_QUERY and if this DCMD is failed then driver will fail
this event processing and will not go ahead for further events. This
will cause infinite loop of same event getting retried infinitely and
causing above mentioned logs.
Fix for this problem is: not to fire DCMD MR_DCMD_PD_LIST_QUERY for
controllers which do not support it and send DCMD SUCCESS status to AEN
function so that it can go ahead with other event processing.
Reported-by: Lucz Geza <geza@lucz.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bba142957e upstream.
c44696fff0 ("EDAC: Remove arbitrary limit on number of channels")
lifted the arbitrary limit on memory controller channels in EDAC.
However, the dynamic channel attributes dynamic_csrow_dimm_attr and
dynamic_csrow_ce_count_attr remained 6.
This wasn't a problem except channels 6 and 7 weren't visible in sysfs
on machines with more than 6 channels after the conversion to static
attr groups with
2c1946b6d6 ("EDAC: Use static attribute groups for managing sysfs entries")
[ without that, we're exploding in edac_create_sysfs_mci_device()
because we're dereferencing out of the bounds of the
dynamic_csrow_dimm_attr array. ]
Add attributes for channels 6 and 7 along with a guard for the
future, should more channels be required and/or to sanity check for
misconfigured machines.
We still need to check against the number of channels present on the MC
first, as Thor reported.
Signed-off-by: Borislav Petkov <bp@suse.de>
Reported-by: Hironobu Ishii <ishii.hironobu@jp.fujitsu.com>
Tested-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23bc6ab0a0 upstream.
When we retrieve imtu value from userspace we should use 16 bit pointer
cast instead of 32 as it's defined that way in headers. Fixes setsockopt
calls on big-endian platforms.
Signed-off-by: Amadeusz Sławiński <amadeusz.slawinski@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 152bc19e2f upstream.
It seems the commit e5262d0568 ("spi: spi-pxa2xx: SPI support for Intel Quark
X1000") misses one place to be adapted for Intel Quark, i.e. in reset_sccr1().
Clear all RFT bits when call reset_sccr1() on Intel Quark.
Fixes: e5262d0568 ("spi: spi-pxa2xx: SPI support for Intel Quark X1000")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7dd91d52a8 upstream.
There is the only failure path in efm32_i2c_probe(),
where clk_disable_unprepare() is missed.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes: 1b5b23718b ("i2c: efm32: new bus driver")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1bea0512c3 upstream.
After discovering there are 2 very different 14e4:4365 PCI devices we
made ID tables less generic. Back then we believed there are only 2 such
devices:
1) 14e4:4365 1028:0016 with SoftMAC BCM43142 chipset
2) 14e4:4365 14e4:4365 with FullMAC BCM4366 chipset
>From the recent report it appears there is also 14e4:4365 105b:e092
which should be claimed by bcma. Add back support for it.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=121881
Fixes: 515b399c9a ("bcma: claim only 14e4:4365 PCI Dell card with SoftMAC BCM43142")
Reported-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f16c3ebfa6 upstream.
Upon firmware load interrupt (FH_TX), the ISR re-enables the
firmware load interrupt only to avoid races with other
flows as described in the commit below. When the firmware
is completely loaded, the thread that is loading the
firmware will enable all the interrupts to make sure that
the driver gets the ALIVE interrupt.
The problem with that is that the thread that is loading
the firmware is actually racing against the ISR and we can
get to the following situation:
CPU0 CPU1
iwl_pcie_load_given_ucode
...
iwl_pcie_load_firmware_chunk
wait_for_interrupt
<interrupt>
ISR handles CSR_INT_BIT_FH_TX
ISR wakes up the thread on CPU0
/* enable all the interrupts
* to get the ALIVE interrupt
*/
iwl_enable_interrupts
ISR re-enables CSR_INT_BIT_FH_TX only
/* start the firmware */
iwl_write32(trans, CSR_RESET, 0);
BUG! ALIVE interrupt will never arrive since it has been
masked by CPU1.
In order to fix that, change the ISR to first check if
STATUS_INT_ENABLED is set. If so, re-enable all the
interrupts. If STATUS_INT_ENABLED is clear, then we can
check what specific interrupt happened and re-enable only
that specific interrupt (RFKILL or FH_TX).
All the credit for the analysis goes to Kirtika who did the
actual debugging work.
Fixes: a6bd005fe9 ("iwlwifi: pcie: fix RF-Kill vs. firmware load race")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2aabdbdc17 upstream.
The NIC's CPU gets started after the firmware has been
written to its memory. The first thing it does is to
send an interrupt to let the driver know that it is
running. In order to get that interrupt, the driver needs
to make sure it is not masked. Of course, the interrupt
needs to be enabled in the driver before the CPU starts to
run.
I mistakenly inversed those two steps leading to races
which prevented the driver from getting the alive interrupt
from the firmware.
Fix that.
Fixes: a6bd005fe9 ("iwlwifi: pcie: fix RF-Kill vs. firmware load race")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 602d1657c6 upstream.
do_div was replaced with div64_u64 at some point, causing a bug with
block calculation due to incompatible semantics of the two functions.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Fixes: a739ff3f54 ("dm verity: add support for forward error correction")
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6311f1261f upstream.
When s5p_mfc_remove() calls put_device() for the reserved memory region
devs, the driver core warns that the dev doesn't have a release callback:
WARNING: CPU: 0 PID: 591 at drivers/base/core.c:251 device_release+0x8c/0x90
Device 's5p-mfc-l' does not have a release() function, it is broken and must be fixed.
Also, the declared DMA memory using dma_declare_coherent_memory() isn't
relased so add a dev .release that calls dma_release_declared_memory().
Fixes: 6e83e6e25e ("[media] s5p-mfc: Fix kernel warning on memory init")
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 29debab0a9 upstream.
The devices don't have a name set, so makes dev_name() returns NULL which
makes harder to identify the devices that are causing issues, for example:
WARNING: CPU: 2 PID: 616 at drivers/base/core.c:251 device_release+0x8c/0x90
Device '(null)' does not have a release() function, it is broken and must be fixed.
And after setting the device name:
WARNING: CPU: 0 PID: 591 at drivers/base/core.c:251 device_release+0x8c/0x90
Device 's5p-mfc-l' does not have a release() function, it is broken and must be fixed.
Fixes: 6e83e6e25e ("[media] s5p-mfc: Fix kernel warning on memory init")
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 28b783e47a upstream.
In xfs_finish_page_writeback(), we have a loop that looks like this:
do {
if (off < bvec->bv_offset)
goto next_bh;
if (off > end)
break;
bh->b_end_io(bh, !error);
next_bh:
off += bh->b_size;
} while ((bh = bh->b_this_page) != head);
The b_end_io function is end_buffer_async_write(), which will call
end_page_writeback() once all the buffers have marked as no longer
under IO. This issue here is that the only thing currently
protecting both the bufferhead chain and the page from being
reclaimed is the PageWriteback state held on the page.
While we attempt to limit the loop to just the buffers covered by
the IO, we still read from the buffer size and follow the next
pointer in the bufferhead chain. There is no guarantee that either
of these are valid after the PageWriteback flag has been cleared.
Hence, loops like this are completely unsafe, and result in
use-after-free issues. One such problem was caught by Calvin Owens
with KASAN:
.....
INFO: Freed in 0x103fc80ec age=18446651500051355200 cpu=2165122683 pid=-1
free_buffer_head+0x41/0x90
__slab_free+0x1ed/0x340
kmem_cache_free+0x270/0x300
free_buffer_head+0x41/0x90
try_to_free_buffers+0x171/0x240
xfs_vm_releasepage+0xcb/0x3b0
try_to_release_page+0x106/0x190
shrink_page_list+0x118e/0x1a10
shrink_inactive_list+0x42c/0xdf0
shrink_zone_memcg+0xa09/0xfa0
shrink_zone+0x2c3/0xbc0
.....
Call Trace:
<IRQ> [<ffffffff81e8b8e4>] dump_stack+0x68/0x94
[<ffffffff8153a995>] print_trailer+0x115/0x1a0
[<ffffffff81541174>] object_err+0x34/0x40
[<ffffffff815436e7>] kasan_report_error+0x217/0x530
[<ffffffff81543b33>] __asan_report_load8_noabort+0x43/0x50
[<ffffffff819d651f>] xfs_destroy_ioend+0x3bf/0x4c0
[<ffffffff819d69d4>] xfs_end_bio+0x154/0x220
[<ffffffff81de0c58>] bio_endio+0x158/0x1b0
[<ffffffff81dff61b>] blk_update_request+0x18b/0xb80
[<ffffffff821baf57>] scsi_end_request+0x97/0x5a0
[<ffffffff821c5558>] scsi_io_completion+0x438/0x1690
[<ffffffff821a8d95>] scsi_finish_command+0x375/0x4e0
[<ffffffff821c3940>] scsi_softirq_done+0x280/0x340
Where the access is occuring during IO completion after the buffer
had been freed from direct memory reclaim.
Prevent use-after-free accidents in this end_io processing loop by
pre-calculating the loop conditionals before calling bh->b_end_io().
The loop is already limited to just the bufferheads covered by the
IO in progress, so the offset checks are sufficient to prevent
accessing buffers in the chain after end_page_writeback() has been
called by the the bh->b_end_io() callout.
Yet another example of why Bufferheads Must Die.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reported-and-Tested-by: Calvin Owens <calvinowens@fb.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eaf9a7361f upstream.
Otherwise, there is potential for both DMF_SUSPENDED* and
DMF_NOFLUSH_SUSPENDING to not be set during dm_suspend() -- which is
definitely _not_ a valid state.
This fix, in conjuction with "dm rq: fix the starting and stopping of
blk-mq queues", addresses the potential for request-based DM multipath's
__multipath_map() to see !dm_noflush_suspending() during suspend.
Reported-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd9f55ea1c upstream.
Commit d548b34b06 ("dm: reduce the queue delay used in dm_request_fn
from 100ms to 10ms") always intended the value to be 10 msecs -- it
just expressed it in jiffies because earlier commit 7eaceaccab ("block:
remove per-queue plugging") did.
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Fixes: d548b34b06 ("dm: reduce the queue delay used in dm_request_fn from 100ms to 10ms")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 04c16b84e4 upstream.
This patch fixes some of the LDOs and BUCKs voltage range as per
user manual of s2mps15 (REV0.4).
Fixes: 51af206758 ("regulator: s2mps11: Add support for S2MPS15 regulators")
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bbdb34c90a upstream.
Fix RC5 decoding with Fintek CIR chipset
Commit e87b540be2 tightened up the RC5
decoding by adding a check for trailing silence to ensure a valid RC5
command had been received. Unfortunately the trailer length checked was
10 units and the Fintek CIR device does not want to provide details of a
space longer than 6350us. This meant that RC5 remotes working on a
Fintek setup on 3.16 failed on 3.17 and later. Fix this by shortening
the trailer check to 6 units (allowing for a previous space in the
received remote command).
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=117221
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 126f402984 upstream.
An earlier patch fixing an input validation issue introduced another
issue: vb2_core_dqbuf() is called with pb argument value NULL in some
cases, causing a NULL pointer dereference. Fix this by skipping the
verification as there's nothing to verify.
Fixes: e7e0c3e265 ("[media] videobuf2-core: Check user space planes array in dqbuf")
Signed-off-by: David R <david@unsolicited.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 83934b75c3 upstream.
When a buffer is being dequeued using VIDIOC_DQBUF IOCTL, the exact buffer
which will be dequeued is not known until the buffer has been removed from
the queue. The number of planes is specific to a buffer, not to the queue.
This does lead to the situation where multi-plane buffers may be requested
and queued with n planes, but VIDIOC_DQBUF IOCTL may be passed an argument
struct with fewer planes.
__fill_v4l2_buffer() however uses the number of planes from the dequeued
videobuf2 buffer, overwriting kernel memory (the m.planes array allocated
in video_usercopy() in v4l2-ioctl.c) if the user provided fewer
planes than the dequeued buffer had. Oops!
Fixes: b0e0e1f83d ("[media] media: videobuf2: Prepare to divide videobuf2")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5cac1f67ea upstream.
If a system configures the Nuvoton chip to use the alternative
EFM IO address (CR_EFIR2) then after probing the primary EFM IO
address (CR_EFIR) this region is not released.
If a driver for another function of the Nuvoton Super I/O
chip uses the same probing mechanism then it will hang if
loaded after the nuvoton-cir driver.
This was reported for the nct6775 hwmon driver.
Fix this by properly releasing the region after probing CR_EFIR.
This regression was introduced with kernel 4.6 so cc it to stable.
Reported-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca6e6126db upstream.
Implement memory barriers according to Documentation/circular-buffers.txt:
- use smp_store_release() to update ringbuffer read/write pointers
- use smp_load_acquire() to load write pointer on reader side
- use ACCESS_ONCE() to load read pointer on writer side
This fixes data stream corruptions observed e.g. on an ARM Cortex-A9
quad core system with different types (PCI, USB) of DVB tuners.
Signed-off-by: Soeren Moch <smoch@web.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a00932f08 upstream.
When disconnecting the usbtv device, the sound card is unregistered
from ALSA and the snd member of the usbtv struct is set to NULL. If
the usbtv snd_trigger work is running, this can cause a race condition
where the kernel will attempt to access free'd resources, shown in
[1].
This patch fixes the disconnection code by cancelling any snd_trigger
work before unregistering the sound card from ALSA and checking that
the snd member still exists in the work function.
[1]:
usb 3-1.2: USB disconnect, device number 6
BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
IP: [<ffffffff81093850>] process_one_work+0x30/0x480
PGD 405bbf067 PUD 405bbe067 PMD 0
Call Trace:
[<ffffffff81093ce8>] worker_thread+0x48/0x4e0
[<ffffffff81093ca0>] ? process_one_work+0x480/0x480
[<ffffffff81093ca0>] ? process_one_work+0x480/0x480
[<ffffffff81099998>] kthread+0xd8/0xf0
[<ffffffff815c73c2>] ret_from_fork+0x22/0x40
[<ffffffff810998c0>] ? kthread_worker_fn+0x170/0x170
---[ end trace 0f3dac5c1a38e610 ]---
Signed-off-by: Matthew Leach <matthew@mattleach.net>
Tested-by: Peter Sutton <foxxy@foxdogstudios.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f37be01e6d upstream.
The RPM has two sets of selectors (IPC bit fields): request and
acknowledge. Apparently, some models use 4*32 bit words for select
and some use 7*32 bit words for request, but all use 7*32 words
for acknowledge bits.
So apparently you can on the models with requests of 4*32 select
bits send 4*32 messages and get 7*32 different replies, so on ACK
interrupt, 7*32 bit words need to be read. This is how the vendor
code apparently works.
Reported-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9835f1b70b upstream.
The RPM in MSM8660/APQ8060 has different offsets to the selector
ACK and request context ACK registers. Make all these register
offsets part of the per-SoC data and assign the right values.
The bug was found by verifying backwards to the vendor tree in
the out-of-tree files <mach/rpm-[8660|8064|8960]>: all were using
offsets 3,11,15,23 and a select size of 4, except the MSM8660/APQ8060
which was using offsets 3,11,19,27 and a select size of 7.
All other platforms apart from msm8660 were affected by reading
excess registers, since 7 was hardcoded as the number of select
words, this patch makes also this part dynamic so we only write/read
as many select words as the platform actually use.
Symptoms of this bug when using msm8660: the first RPM transaction
would work, but the next would stall or raise an error since the
previous transaction was not properly ACKed as the ACK words were
read at the wrong offset.
Fixes: 58e214382b ("mfd: qcom-rpm: Driver for the Qualcomm RPM")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Björn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5fc8f707a2 upstream.
If MSR_CONFIG_TDP_CONTROL is locked, we currently try to address some
MSR 0x80000648 or so. Mask out the relevant level bits 0 and 1.
Found while running over the Jailhouse hypervisor which became upset
about this strange MSR index.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c427c42cd6 upstream.
Commit 1e133ab296 ("s390/mm: split arch/s390/mm/pgtable.c") changed
the return value of get_guest_storage_key to an unsigned char, resulting
in -EFAULT getting interpreted as a valid storage key.
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f045402984 upstream.
__tlb_flush_asce() should never be used if multiple asce belong to a mm.
As this function changes mm logic determining if local or global tlb
flushes will be neded, we might end up flushing only the gmap asce on all
CPUs and a follow up mm asce flushes will only flush on the local CPU,
although that asce ran on multiple CPUs.
The missing tlb flushes will provoke strange faults in user space and even
low address protections in user space, crashing the kernel.
Fixes: 1b948d6cae ("s390/mm,tlb: optimize TLB flushing for zEC12")
Reported-by: Sascha Silbe <silbe@linux.vnet.ibm.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f5d050cea upstream.
Prior to commit 1bc6664bdf a call to
enable_cmf for a device for which channel measurement was already
enabled resulted in a reset of the measurement data.
What looked like bugs at the time (a 2nd allocation was triggered
but failed, reset was called regardless of previous failures, and
errors have not been reported to userspace) was actually something
at least one userspace tool depended on. Restore that behavior in
a sane way.
Fixes: 1bc6664bdf ("s390/cio: use device_lock during cmb activation")
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c43203cab1 upstream.
If the processor exits to KVM while delivering an interrupt,
the hypervisor then requeues the interrupt for the next vmentry.
Trying to enter SMM in this same window causes to enter non-root
mode in emulated SMM (i.e. with IF=0) and with a request to
inject an IRQ (i.e. with a valid VM-entry interrupt info field).
This is invalid guest state (SDM 26.3.1.4 "Check on Guest RIP
and RFLAGS") and the processor fails vmentry.
The fix is to defer the injection from KVM_REQ_SMI to KVM_REQ_EVENT,
like we already do for e.g. NMIs. This patch doesn't change the
name of the process_smi function so that it can be applied to
stable releases. The next patch will modify the names so that
process_nmi and process_smi handle respectively KVM_REQ_NMI and
KVM_REQ_SMI.
This is especially common with Windows, probably due to the
self-IPI trick that it uses to deliver deferred procedure
calls (DPCs).
Reported-by: Laszlo Ersek <lersek@redhat.com>
Reported-by: Michał Zegan <webczat_200@poczta.onet.pl>
Fixes: 64d6067057
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f1fe81123 upstream.
When freeing the nested resources of a vcpu, there is an assumption that
the vcpu's vmcs01 is the current VMCS on the CPU that executes
nested_release_vmcs12(). If this assumption is violated, the vcpu's
vmcs01 may be made active on multiple CPUs at the same time, in
violation of Intel's specification. Moreover, since the vcpu's vmcs01 is
not VMCLEARed on every CPU on which it is active, it can linger in a
CPU's VMCS cache after it has been freed and potentially
repurposed. Subsequent eviction from the CPU's VMCS cache on a capacity
miss can result in memory corruption.
It is not sufficient for vmx_free_vcpu() to call vmx_load_vmcs01(). If
the vcpu in question was last loaded on a different CPU, it must be
migrated to the current CPU before calling vmx_load_vmcs01().
Signed-off-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b244c9fc25 upstream.
With PML enabled, guest will shut down if a PML full VMEXIT occurs during
event delivery. According to Intel SDM 27.2.3, PML full VMEXIT can occur when
event is being delivered through IDT, so KVM should not exit to user space
with error. Instead, it should let EXIT_REASON_PML_FULL go through and the
event will be re-injected on the next VMENTRY.
Signed-off-by: Lei Cao <lei.cao@stratus.com>
Fixes: 843e433057 ("KVM: VMX: Add PML support in VMX")
[Shortened the summary and Cc'd stable.]
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 93d17397e4 upstream.
It turns out that if the guest does a H_CEDE while the CPU is in
a transactional state, and the H_CEDE does a nap, and the nap
loses the architected state of the CPU (which is is allowed to do),
then we lose the checkpointed state of the virtual CPU. In addition,
the transactional-memory state recorded in the MSR gets reset back
to non-transactional, and when we try to return to the guest, we take
a TM bad thing type of program interrupt because we are trying to
transition from non-transactional to transactional with a hrfid
instruction, which is not permitted.
The result of the program interrupt occurring at that point is that
the host CPU will hang in an infinite loop with interrupts disabled.
Thus this is a denial of service vulnerability in the host which can
be triggered by any guest (and depending on the guest kernel, it can
potentially triggered by unprivileged userspace in the guest).
This vulnerability has been assigned the ID CVE-2016-5412.
To fix this, we save the TM state before napping and restore it
on exit from the nap, when handling a H_CEDE in real mode. The
case where H_CEDE exits to host virtual mode is already OK (as are
other hcalls which exit to host virtual mode) because the exit
path saves the TM state.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f024ee0984 upstream.
This moves the transactional memory state save and restore sequences
out of the guest entry/exit paths into separate procedures. This is
so that these sequences can be used in going into and out of nap
in a subsequent patch.
The only code changes here are (a) saving and restore LR on the
stack, since these new procedures get called with a bl instruction,
(b) explicitly saving r1 into the PACA instead of assuming that
HSTATE_HOST_R1(r13) is already set, and (c) removing an unnecessary
and redundant setting of MSR[TM] that should have been removed by
commit 9d4d0bdd9e0a ("KVM: PPC: Book3S HV: Add transactional memory
support", 2013-09-24) but wasn't.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dfbca61af0 upstream.
In create_safe_exec_page(), we create a copy of the hibernate exit text,
along with some page tables to map this via TTBR0. We then install the
new tables in TTBR0.
In swsusp_arch_resume() we call create_safe_exec_page() before trying a
number of operations which may fail (e.g. copying the linear map page
tables). If these fail, we bail out of swsusp_arch_resume() and return
an error code, but leave TTBR0 as-is. Subsequently, the core hibernate
code will call free_basic_memory_bitmaps(), which will free all of the
memory allocations we made, including the page tables installed in
TTBR0.
Thus, we may have TTBR0 pointing at dangling freed memory for some
period of time. If the hibernate attempt was triggered by a user
requesting a hibernate test via the reboot syscall, we may return to
userspace with the clobbered TTBR0 value.
Avoid these issues by reorganising swsusp_arch_resume() such that we
have no failure paths after create_safe_exec_page(). We also add a check
that the zero page allocation succeeded, matching what we have for other
allocations.
Fixes: 82869ac57b ("arm64: kernel: Add support for hibernate/suspend-to-disk")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: James Morse <james.morse@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0194e760f7 upstream.
In create_safe_exec_page we install a set of global mappings in TTBR0,
then subsequently invalidate TLBs. While TTBR0 points at the zero page,
and the TLBs should be free of stale global entries, we may have stale
ASID-tagged entries (e.g. from the EFI runtime services mappings) for
the same VAs. Per the ARM ARM these ASID-tagged entries may conflict
with newly-allocated global entries, and we must follow a
Break-Before-Make approach to avoid issues resulting from this.
This patch reworks create_safe_exec_page to invalidate TLBs while the
zero page is still in place, ensuring that there are no potential
conflicts when the new TTBR0 value is installed. As a single CPU is
online while this code executes, we do not need to perform broadcast TLB
maintenance, and can call local_flush_tlb_all(), which also subsumes
some barriers. The remaining assembly is converted to use write_sysreg()
and isb().
Other than this, we safely manipulate TTBRs in the hibernate dance. The
code we install as part of the new TTBR0 mapping (the hibernated
kernel's swsusp_arch_suspend_exit) installs a zero page into TTBR1,
invalidates TLBs, then installs its preferred value. Upon being restored
to the middle of swsusp_arch_suspend, the new image will call
__cpu_suspend_exit, which will call cpu_uninstall_idmap, installing the
zero page in TTBR0 and invalidating all TLB entries.
Fixes: 82869ac57b ("arm64: kernel: Add support for hibernate/suspend-to-disk")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: James Morse <james.morse@arm.com>
Tested-by: James Morse <james.morse@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 89581f06b2 upstream.
We need to set cpsr before determining the spsr bank, as the bank
depends on the target exception level of the injection, not the
current mode of the vcpu. Normally this is one in the same (EL1),
but not when we manage to trap an EL0 fault. It still doesn't really
matter for the 64-bit EL0 case though, as vcpu_spsr() unconditionally
uses the EL1 bank for that. However the 32-bit EL0 case gets fun, as
that path will lead to the BUG() in vcpu_spsr32().
This patch fixes the assignment order and also modifies some white
space in order to better group pairs of lines that have strict order.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d6732fc402 upstream.
Due to the untyped KIMAGE_VADDR constant, the linker may not notice
that the __rela_offset and __dynsym_offset expressions are absolute
values (i.e., are not subject to relocation). This does not matter for
KASLR, but it does confuse kallsyms in relative mode, since it uses
the lowest non-absolute symbol address as the anchor point, and expects
all other symbol addresses to be within 4 GB of it.
Fix this by qualifying these expressions as ABSOLUTE() explicitly.
Fixes: 0cd3defe0a ("arm64: kernel: perform relocation processing from ID map")
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 04a8481061 upstream.
As reported by Zijun, the fdt_check_header() call in __fixmap_remap_fdt()
is not safe since it is not guaranteed that the FDT header is mapped
completely. Due to the minimum alignment of 8 bytes, the only fields we
can assume to be mapped are 'magic' and 'totalsize'.
Since the OF layer is in charge of validating the FDT image, and we are
only interested in making reasonably sure that the size field contains
a meaningful value, replace the fdt_check_header() call with an explicit
comparison of the magic field's value against the expected value.
Reported-by: Zijun Hu <zijun_hu@htc.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ad1cfdf518 upstream.
The 2nd additional region is the GIC virtual cpu interface register
base and size.
As the gic400 of rk3368 says, the cpu interface register map as below
:
-0x0000 GICC_CTRL
.
.
.
-0x00fc GICC_IIDR
-0x1000 GICC_IDR
Obviously, the region size should be greater than 0x1000.
So we should make sure to include the GICC_IDR since the kernel will access
it in some cases.
Fixes: b790c2cab5 ("arm64: dts: add Rockchip rk3368 core dtsi and board dts for the r88 board")
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[added Fixes and stable-cc]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
commit 0bd50d719b upstream.
Due to a silicon issue on the Atom X5-Z8000 "Cherry Trail" processor
series, a common lock must be used to prevent concurrent accesses
across the 4 GPIO controllers managed by this driver.
See Intel Atom Z8000 Processor Series Specification Update
(Rev. 005), errata #CHT34, for further information.
Signed-off-by: Dan O'Donovan <dan@emutex.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd3b204af1 upstream.
The error handling is not correct since the commit 3f7dbfd8ee ("gpio:
intel-mid: switch to using gpiolib irqchip helpers"). Switch to devres API to
fix the potential resource leak.
Fixes: commit 3f7dbfd8ee ("gpio: intel-mid: switch to using gpiolib irqchip helpers")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3dbd3212f8 upstream.
The commit d56d6b3d7d ("gpio: langwell: add Intel Merrifield support")
doesn't look at all as a proper support for Intel Merrifield and I dare to say
that it distorts the behaviour of the hardware.
The register map is different on Intel Merrifield, i.e. only 6 out of 8
register have the same purpose but none of them has same location in the
address space. The current case potentially harmful to existing hardware since
it's poking registers on wrong offsets and may set some pin to be GPIO output
when connected hardware doesn't expect such.
Besides the above GPIO and pinctrl on Intel Merrifield have been located in
different IP blocks. The functionality has been extended as well, i.e. added
support of level interrupts, special registers for wake capable sources and
thus, in my opinion, requires a completele separate driver.
If someone wondering the existing gpio-intel-mid.c would be converted to actual
pinctrl (which by the fact it is now), though I wouldn't be a volunteer to do
that.
Fixes: d56d6b3d7d ("gpio: langwell: add Intel Merrifield support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a246b8198f upstream.
NBANK() macro assumes that ngpios is a multiple of 8(BANK_SZ) and
hence results in 0 banks for PCA9536 which has just 4 gpios. This is
wrong as PCA9356 has 1 bank with 4 gpios. This results in uninitialized
PCA953X_INVERT register. Fix this by using DIV_ROUND_UP macro in
NBANK().
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e51e4d8a18 upstream.
When the clk_get() of "uart" clock returns EPROBE_DEFER, the next re-probe
finishes with success but uses invalid (ERR_PTR) values. This leads to
dereferencing of ERR_PTR stored under ourport->clk:
12c30000.serial: Controller clock not found
(...)
12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 61, base_baud = 0) is a S3C6400/10
Unable to handle kernel paging request at virtual address fffffdfb
(clk_prepare) from [<c039f7d0>] (s3c24xx_serial_pm+0x20/0x128)
(s3c24xx_serial_pm) from [<c0395414>] (uart_change_pm+0x38/0x40)
(uart_change_pm) from [<c039689c>] (uart_add_one_port+0x31c/0x44c)
(uart_add_one_port) from [<c03a035c>] (s3c24xx_serial_probe+0x2a8/0x418)
(s3c24xx_serial_probe) from [<c03ee110>] (platform_drv_probe+0x50/0xb0)
(platform_drv_probe) from [<c03ecb44>] (driver_probe_device+0x1f4/0x2b0)
(driver_probe_device) from [<c03eb0c0>] (bus_for_each_drv+0x44/0x8c)
(bus_for_each_drv) from [<c03ec8c8>] (__device_attach+0x9c/0x100)
(__device_attach) from [<c03ebf54>] (bus_probe_device+0x84/0x8c)
(bus_probe_device) from [<c03ec388>] (deferred_probe_work_func+0x60/0x8c)
(deferred_probe_work_func) from [<c012fee4>] (process_one_work+0x120/0x328)
(process_one_work) from [<c0130150>] (worker_thread+0x2c/0x4ac)
(worker_thread) from [<c0135320>] (kthread+0xd8/0xf4)
(kthread) from [<c0107978>] (ret_from_fork+0x14/0x3c)
The first unsuccessful clk_get() causes s3c24xx_serial_init_port() to
exit with failure but the s3c24xx_uart_port is left half-configured
(e.g. port->mapbase is set, clk contains ERR_PTR). On next re-probe,
the function s3c24xx_serial_init_port() will exit early with success
because of configured port->mapbase and driver will use old values,
including the ERR_PTR as clock.
Fix this by cleaning the port->mapbase on error path so each re-probe
will initialize all of the port settings.
Fixes: 60e9357547 ("serial: samsung: enable clock before clearing pending interrupts during init")
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 30acf549ca upstream.
For dm uarts in pio mode tx data is transferred to the fifo register 4
bytes at a time, but care is not taken when these 4 bytes spans the end
of the xmit buffer so the loop might read up to 3 bytes past the buffer
and then skip the actual data at the beginning of the buffer.
Fix this by, analogous to the DMA case, make sure the chunk doesn't
wrap the xmit buffer.
Fixes: 3a878c430f ("tty: serial: msm: Add TX DMA support")
Cc: Ivan Ivanov <iivanov.xz@gmail.com>
Reported-by: Frank Rowand <frowand.list@gmail.com>
Reported-by: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Andy Gross <andy.gross@linaro.org>
Tested-by: Frank Rowand <frank.rowand@am.sony.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e75118a7b5 upstream.
Passing "nosmp" should boot the kernel with a single processor, without
provision to enable secondary CPUs even if they are present. "nosmp" is
implemented by setting maxcpus=0. At the moment we still mark the secondary
CPUs present even with nosmp, which allows the userspace to bring them
up. This patch corrects the smp_prepare_cpus() to honor the maxcpus == 0.
Commit 44dbcc93ab ("arm64: Fix behavior of maxcpus=N") fixed the
behavior for maxcpus >= 1, but broke maxcpus = 0.
Fixes: 44dbcc93ab ("arm64: Fix behavior of maxcpus=N")
Cc: Will Deacon <will.deacon@arm.com>
Cc: James Morse <james.morse@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
[catalin.marinas@arm.com: updated code comment]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b9c220b589 upstream.
Selecting CONFIG_RANDOMIZE_BASE=y and CONFIG_MODULES=n fails to build
the module PLTs support:
CC arch/arm64/kernel/module-plts.o
/work/Linux/linux-2.6-aarch64/arch/arm64/kernel/module-plts.c: In function ‘module_emit_plt_entry’:
/work/Linux/linux-2.6-aarch64/arch/arm64/kernel/module-plts.c:32:49: error: dereferencing pointer to incomplete type ‘struct module’
This patch selects ARM64_MODULE_PLTS conditionally only if MODULES is
enabled.
Fixes: f80fb3a3d5 ("arm64: add support for kernel ASLR")
Reported-by: Jeff Vander Stoep <jeffv@google.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9113c2aa05 upstream.
In smp_prepare_boot_cpu(), we invoke cpuinfo_store_boot_cpu to store
the cpuinfo in a per-cpu ptr, before initialising the per-cpu offset for
the boot CPU. This patch reorders the sequence to make sure we initialise
the per-cpu offset before accessing the per-cpu area.
Commit 4b998ff188 ("arm64: Delay cpuinfo_store_boot_cpu") fixed the
issue where we modified the per-cpu area even before the kernel initialises
the per-cpu areas, but failed to wait until the boot cpu updated it's
offset.
Fixes: 4b998ff188 ("arm64: Delay cpuinfo_store_boot_cpu")
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2ce39ad151 upstream.
Clearing PSTATE.D is one of the requirements for generating a debug
exception. The arm64 booting protocol requires that PSTATE.D is set,
since many of the debug registers (for example, the hw_breakpoint
registers) are UNKNOWN out of reset and could potentially generate
spurious, fatal debug exceptions in early boot code if PSTATE.D was
clear. Once the debug registers have been safely initialised, PSTATE.D
is cleared, however this is currently broken for two reasons:
(1) The boot CPU clears PSTATE.D in a postcore_initcall and secondary
CPUs clear PSTATE.D in secondary_start_kernel. Since the initcall
runs after SMP (and the scheduler) have been initialised, there is
no guarantee that it is actually running on the boot CPU. In this
case, the boot CPU is left with PSTATE.D set and is not capable of
generating debug exceptions.
(2) In a preemptible kernel, we may explicitly schedule on the IRQ
return path to EL1. If an IRQ occurs with PSTATE.D set in the idle
thread, then we may schedule the kthread_init thread, run the
postcore_initcall to clear PSTATE.D and then context switch back
to the idle thread before returning from the IRQ. The exception
return path will then restore PSTATE.D from the stack, and set it
again.
This patch fixes the problem by moving the clearing of PSTATE.D earlier
to proc.S. This has the desirable effect of clearing it in one place for
all CPUs, long before we have to worry about the scheduler or any
exception handling. We ensure that the previous reset of MDSCR_EL1 has
completed before unmasking the exception, so that any spurious
exceptions resulting from UNKNOWN debug registers are not generated.
Without this patch applied, the kprobes selftests have been seen to fail
under KVM, where we end up attempting to step the OOL instruction buffer
with PSTATE.D set and therefore fail to complete the step.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c47eb1c18 upstream.
The kprobe enablement work has uncovered that changes made by
a guest to MDSCR_EL1 were propagated to the host when VHE was
enabled, leading to unexpected exception being delivered.
Moving this register to the list of registers that are always
context-switched fixes the issue.
Fixes: 9c6c356832 ("arm64: KVM: VHE: Split save/restore of registers shared between guest and host")
Reported-by: Tirumalesh Chalamarla <Tirumalesh.Chalamarla@cavium.com>
Tested-by: Tirumalesh Chalamarla <Tirumalesh.Chalamarla@cavium.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4fdef69838 upstream.
This patch fixes an issue that the xfer_work() is possible to cause
NULL pointer dereference if the usb cable is disconnected while data
transfer is running.
In such case, a gadget driver may call usb_ep_disable()) before
xfer_work() is actually called. In this case, the usbhs_pkt_pop()
will call usbhsf_fifo_unselect(), and then usbhs_pipe_to_fifo()
in xfer_work() will return NULL.
Fixes: e73a989 ("usb: renesas_usbhs: add DMAEngine support")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c0415fa08 upstream.
This patch adds support for 0x1206 PID of Telit LE910.
Since the interfaces positions are the same than the ones for
0x1043 PID of Telit LE922, telit_le922_blacklist_usbcfg3 is used.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9cad39fe4e upstream.
commit f3af36511e ("usb: dwc3: gadget: always
enable IOC on bulk/interrupt transfers") ended up
regressing Isochronous endpoints by clearing
DWC3_EP_BUSY flag too early, which resulted in
choppy audio playback over USB.
Fix that by partially reverting original commit and
making sure that we check for isochronous endpoints.
Fixes: f3af36511e ("usb: dwc3: gadget: always enable IOC
on bulk/interrupt transfers")
Signed-off-by: Konrad Leszczynski <konrad.leszczynski@intel.com>
Signed-off-by: Rafal Redzimski <rafal.f.redzimski@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 15e4292a2d upstream.
This patch fixes an issue that the CFIFOSEL register value is possible
to be changed by usbhsg_ep_enable() wrongly. And then, a data transfer
using CFIFO may not work correctly.
For example:
# modprobe g_multi file=usb-storage.bin
# ifconfig usb0 192.168.1.1 up
(During the USB host is sending file to the mass storage)
# ifconfig usb0 down
In this case, since the u_ether.c may call usb_ep_enable() in
eth_stop(), if the renesas_usbhs driver is also using CFIFO for
mass storage, the mass storage may not work correctly.
So, this patch adds usbhs_lock() and usbhs_unlock() calling in
usbhsg_ep_enable() to protect CFIFOSEL register. This is because:
- CFIFOSEL.CURPIPE = 0 is also needed for the pipe configuration
- The CFIFOSEL (fifo->sel) is already protected by usbhs_lock()
Fixes: 97664a207b ("usb: renesas_usbhs: shrink spin lock area")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d23d16a88 upstream.
The above commit reordered spin_lock/unlock and now `&dev->lock' is acquired
(rather than released) before calling `dev->driver->disconnect',
`dev->driver->setup', `dev->driver->suspend', `usb_gadget_giveback_request', and
`usb_gadget_udc_reset'.
But this *may* not be the right way to fix the problem pointed by d3cb25a121.
Note that the other usb/gadget/udc drivers do release the lock before calling
these functions. There are also inconsistencies within pch_udc.c, where
`dev->driver->disconnect' is called while holding `&dev->lock' in lines 613 and
1184, but not in line 2739.
Finally, commit d3cb25a121 may have introduced several potential deadlocks.
For instance, EBA (https://github.com/models-team/eba) reports:
Double lock in drivers/usb/gadget/udc/pch_udc.c
first at 2791: spin_lock(& dev->lock); [pch_udc_isr]
second at 2694: spin_lock(& dev->lock); [pch_udc_svc_cfg_interrupt]
after calling from 2793: pch_udc_dev_isr(dev, dev_intr);
after calling from 2724: pch_udc_svc_cfg_interrupt(dev);
Similarly, other potential deadlocks are 2791 -> 2793 -> 2721 -> 2657; and
2791 -> 2793 -> 2711 -> 2573 -> 1499 -> 1480.
Fixes: d3cb25a121 ("usb: gadget: udc: fix spin_lock in pch_udc")
Signed-off-by: Iago Abal <mail@iagoabal.eu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ab2a92e7a6 upstream.
As a micro-power optimization, let's only resume the
USB2 PHY if we're working on <=HIGHSPEED. If we're
gonna work on SUPERSPEED or SUPERSPEED+, there's no
point in resuming the USB2 PHY.
Fixes: 2b0f11df84 ("usb: dwc3: gadget: clear SUSPHY bit before ep cmds")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 554a5ccc4e upstream.
If we hit this error when mounted with errors=continue or
errors=remount-ro:
EXT4-fs error (device loop0): ext4_mb_mark_diskspace_used:2940: comm ext4.exe: Allocating blocks 5090-6081 which overlap fs metadata
then ext4_mb_new_blocks() will call ext4_mb_release_context() and try to
continue. However, ext4_mb_release_context() is the wrong thing to call
here since we are still actually using the allocation context.
Instead, just error out. We could retry the allocation, but there is a
possibility of getting stuck in an infinite loop instead, so this seems
safer.
[ Fixed up so we don't return EAGAIN to userspace. --tytso ]
Fixes: 8556e8f3b6 ("ext4: Don't allow new groups to be added during block allocation")
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c65d5c6c81 upstream.
If we encounter a filesystem error during orphan cleanup, we should stop.
Otherwise, we may end up in an infinite loop where the same inode is
processed again and again.
EXT4-fs (loop0): warning: checktime reached, running e2fsck is recommended
EXT4-fs error (device loop0): ext4_mb_generate_buddy:758: group 2, block bitmap and bg descriptor inconsistent: 6117 vs 0 free clusters
Aborting journal on device loop0-8.
EXT4-fs (loop0): Remounting filesystem read-only
EXT4-fs error (device loop0) in ext4_free_blocks:4895: Journal has aborted
EXT4-fs error (device loop0) in ext4_do_update_inode:4893: Journal has aborted
EXT4-fs error (device loop0) in ext4_do_update_inode:4893: Journal has aborted
EXT4-fs error (device loop0) in ext4_ext_remove_space:3068: IO failure
EXT4-fs error (device loop0) in ext4_ext_truncate:4667: Journal has aborted
EXT4-fs error (device loop0) in ext4_orphan_del:2927: Journal has aborted
EXT4-fs error (device loop0) in ext4_do_update_inode:4893: Journal has aborted
EXT4-fs (loop0): Inode 16 (00000000618192a0): orphan list check failed!
[...]
EXT4-fs (loop0): Inode 16 (0000000061819748): orphan list check failed!
[...]
EXT4-fs (loop0): Inode 16 (0000000061819bf0): orphan list check failed!
[...]
See-also: c9eb13a910 ("ext4: fix hang when processing corrupted orphaned inode list")
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b9554dc5b upstream.
If s_reserved_gdt_blocks is extremely large, it's possible for
ext4_init_block_bitmap(), which is called when ext4 sets up an
uninitialized block bitmap, to corrupt random kernel memory. Add the
same checks which e2fsck has --- it must never be larger than
blocksize / sizeof(__u32) --- and then add a backup check in
ext4_init_block_bitmap() in case the superblock gets modified after
the file system is mounted.
Reported-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6a7fd522a7 upstream.
If ext4_fill_super() fails early, it's possible for ext4_evict_inode()
to call ext4_should_journal_data() before superblock options and flags
are fully set up. In that case, the iput() on the journal inode can
end up causing a BUG().
Work around this problem by reordering the tests so we only call
ext4_should_journal_data() after we know it's not the journal inode.
Fixes: 2d859db3e4 ("ext4: fix data corruption in inodes with journalled data")
Fixes: 2b405bfa84 ("ext4: fix data=journal fast mount/umount hang")
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 646caa9c8e upstream.
Commit 06bd3c36a7 (ext4: fix data exposure after a crash) uncovered a
deadlock in ext4_writepages() which was previously much harder to hit.
After this commit xfstest generic/130 reproduces the deadlock on small
filesystems.
The problem happens when ext4_do_update_inode() sets LARGE_FILE feature
and marks current inode handle as synchronous. That subsequently results
in ext4_journal_stop() called from ext4_writepages() to block waiting for
transaction commit while still holding page locks, reference to io_end,
and some prepared bio in mpd structure each of which can possibly block
transaction commit from completing and thus results in deadlock.
Fix the problem by releasing page locks, io_end reference, and
submitting prepared bio before calling ext4_journal_stop().
[ Changed to defer the call to ext4_journal_stop() only if the handle
is synchronous. --tytso ]
Reported-and-tested-by: Eryu Guan <eguan@redhat.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f70749ca42 upstream.
An extent with lblock = 4294967295 and len = 1 will pass the
ext4_valid_extent() test:
ext4_lblk_t last = lblock + len - 1;
if (len == 0 || lblock > last)
return 0;
since last = 4294967295 + 1 - 1 = 4294967295. This would later trigger
the BUG_ON(es->es_lblk + es->es_len < es->es_lblk) in ext4_es_end().
We can simplify it by removing the - 1 altogether and changing the test
to use lblock + len <= lblock, since now if len = 0, then lblock + 0 ==
lblock and it fails, and if len > 0 then lblock + len > lblock in order
to pass (i.e. it doesn't overflow).
Fixes: 5946d0893 ("ext4: check for overlapping extents in ext4_valid_extent_entries()")
Fixes: 2f974865f ("ext4: check for zero length extent explicitly")
Cc: Eryu Guan <guaneryu@gmail.com>
Signed-off-by: Phil Turnbull <phil.turnbull@oracle.com>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2c1659b4f upstream.
As suggested by the serial port infrastructure documentation, the IRQ is
requested in ->startup(). However, it is never freed in the ->shutdown()
hook.
With simple systems that open the serial port once for all and always
have at least one process that keep the serial port opened, there was no
problem. But with a more complicated system (*cough* systemd *cough*),
the serial port is opened/closed many times, which at some point no
processes having the serial port open at all. Due to this ->startup()
gets called again, tries to request_irq() again, which fails.
Fixes: 30530791a7 ("serial: mvebu-uart: initial support for Armada-3700 serial port")
Cc: Ofer Heifetz <oferh@marvell.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5f070e81be upstream.
When there is more data to be processed, the current test in
scatterwalk_done may prevent us from calling pagedone even when
we should.
In particular, if we're on an SG entry spanning multiple pages
where the last page is not a full page, we will incorrectly skip
calling pagedone on the second last page.
This patch fixes this by adding a separate test for whether we've
reached the end of a page.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b30bdfa864 upstream.
As it is if you ask for a sync gcm you may actually end up with
an async one because it does not filter out async implementations
of ghash.
This patch fixes this by adding the necessary filter when looking
for ghash.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit da7d3abe1c upstream.
This reverts commit 790d849bf8.
Using a v4.7-rc7 kernel on a HP ProLiant triggered following messages
pcc-cpufreq: (v1.10.00) driver loaded with frequency limits: 1200 MHz, 2800 MHz
cpufreq: ondemand governor failed, too long transition latency of HW, fallback to performance governor
The last line was shown for each CPU in the system.
Testing v4.5 (where commit 790d849b was integrated) triggered
similar messages. Same behaviour on a 2nd HP Proliant system.
So commit 790d849bf (cpufreq: pcc-cpufreq: update default value of
cpuinfo_transition_latency) causes the system to use performance
governor which, I guess, was not the intention of the patch.
Enabling debug output in pcc-cpufreq provides following verbose output:
pcc-cpufreq: (v1.10.00) driver loaded with frequency limits: 1200 MHz, 2800 MHz
pcc_get_offset: for CPU 0: pcc_cpu_data input_offset: 0x44, pcc_cpu_data output_offset: 0x48
init: policy->max is 2800000, policy->min is 1200000
get: get_freq for CPU 0
get: SUCCESS: (virtual) output_offset for cpu 0 is 0xffffc9000d7c0048, contains a value of: 0xff06. Speed is: 168000 MHz
cpufreq: ondemand governor failed, too long transition latency of HW, fallback to performance governor
target: CPU 0 should go to target freq: 2800000 (virtual) input_offset is 0xffffc9000d7c0044
target: was SUCCESSFUL for cpu 0
I am asking to revert 790d849bf to re-enable usage of ondemand
governor with pcc-cpufreq.
Fixes: 790d849bf (cpufreq: pcc-cpufreq: update default value of cpuinfo_transition_latency)
Signed-off-by: Andreas Herrmann <aherrmann@suse.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 47be61845c upstream.
We triggered soft-lockup under stress test which
open/access/write/close one file concurrently on more than
five different CPUs:
WARN: soft lockup - CPU#0 stuck for 11s! [who:30631]
...
[<ffffffc0003986f8>] dput+0x100/0x298
[<ffffffc00038c2dc>] terminate_walk+0x4c/0x60
[<ffffffc00038f56c>] path_lookupat+0x5cc/0x7a8
[<ffffffc00038f780>] filename_lookup+0x38/0xf0
[<ffffffc000391180>] user_path_at_empty+0x78/0xd0
[<ffffffc0003911f4>] user_path_at+0x1c/0x28
[<ffffffc00037d4fc>] SyS_faccessat+0xb4/0x230
->d_lock trylock may failed many times because of concurrently
operations, and dput() may execute a long time.
Fix this by replacing cpu_relax() with cond_resched().
dput() used to be sleepable, so make it sleepable again
should be safe.
Signed-off-by: Wei Fang <fangwei1@huawei.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e390b2b2f upstream.
This reverts commit f9054c70d2 ("mm, mempool: only set __GFP_NOMEMALLOC
if there are free elements").
There has been a report about OOM killer invoked when swapping out to a
dm-crypt device. The primary reason seems to be that the swapout out IO
managed to completely deplete memory reserves. Ondrej was able to
bisect and explained the issue by pointing to f9054c70d2 ("mm,
mempool: only set __GFP_NOMEMALLOC if there are free elements").
The reason is that the swapout path is not throttled properly because
the md-raid layer needs to allocate from the generic_make_request path
which means it allocates from the PF_MEMALLOC context. dm layer uses
mempool_alloc in order to guarantee a forward progress which used to
inhibit access to memory reserves when using page allocator. This has
changed by f9054c70d2 ("mm, mempool: only set __GFP_NOMEMALLOC if
there are free elements") which has dropped the __GFP_NOMEMALLOC
protection when the memory pool is depleted.
If we are running out of memory and the only way forward to free memory
is to perform swapout we just keep consuming memory reserves rather than
throttling the mempool allocations and allowing the pending IO to
complete up to a moment when the memory is depleted completely and there
is no way forward but invoking the OOM killer. This is less than
optimal.
The original intention of f9054c70d2 was to help with the OOM
situations where the oom victim depends on mempool allocation to make a
forward progress. David has mentioned the following backtrace:
schedule
schedule_timeout
io_schedule_timeout
mempool_alloc
__split_and_process_bio
dm_request
generic_make_request
submit_bio
mpage_readpages
ext4_readpages
__do_page_cache_readahead
ra_submit
filemap_fault
handle_mm_fault
__do_page_fault
do_page_fault
page_fault
We do not know more about why the mempool is depleted without being
replenished in time, though. In any case the dm layer shouldn't depend
on any allocations outside of the dedicated pools so a forward progress
should be guaranteed. If this is not the case then the dm should be
fixed rather than papering over the problem and postponing it to later
by accessing more memory reserves.
mempools are a mechanism to maintain dedicated memory reserves to
guaratee forward progress. Allowing them an unbounded access to the
page allocator memory reserves is going against the whole purpose of
this mechanism.
Bisected by Ondrej Kozina.
[akpm@linux-foundation.org: coding-style fixes]
Link: http://lkml.kernel.org/r/20160721145309.GR26379@dhcp22.suse.cz
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reported-by: Ondrej Kozina <okozina@redhat.com>
Reviewed-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: NeilBrown <neilb@suse.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Mikulas Patocka <mpatocka@redhat.com>
Cc: Ondrej Kozina <okozina@redhat.com>
Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Cc: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9ebce595f6 upstream.
fuse_flush() calls write_inode_now() that triggers writeback, but actual
writeback will happen later, on fuse_sync_writes(). If an error happens,
fuse_writepage_end() will set error bit in mapping->flags. So, we have to
check mapping->flags after fuse_sync_writes().
Signed-off-by: Maxim Patlasov <mpatlasov@virtuozzo.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Fixes: 4d99ff8f12 ("fuse: Turn writeback cache on")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ac7f052b9e upstream.
Due to implementation of fuse writeback filemap_write_and_wait_range() does
not catch errors. We have to do this directly after fuse_sync_writes()
Signed-off-by: Alexey Kuznetsov <kuznet@virtuozzo.com>
Signed-off-by: Maxim Patlasov <mpatlasov@virtuozzo.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Fixes: 4d99ff8f12 ("fuse: Turn writeback cache on")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4ce827b4cc upstream.
In kernel bug 150021, a kernel panic was reported when restoring a
hibernate image. Only a picture of the oops was reported, so I can't
paste the whole thing here. But here are the most interesting parts:
kernel tried to execute NX-protected page - exploit attempt? (uid: 0)
BUG: unable to handle kernel paging request at ffff8804615cfd78
...
RIP: ffff8804615cfd78
RSP: ffff8804615f0000
RBP: ffff8804615cfdc0
...
Call Trace:
do_signal+0x23
exit_to_usermode_loop+0x64
...
The RIP is on the same page as RBP, so it apparently started executing
on the stack.
The bug was bisected to commit ef0f3ed5a4 (x86/asm/power: Create
stack frames in hibernate_asm_64.S), which in retrospect seems quite
dangerous, since that code saves and restores the stack pointer from a
global variable ('saved_context').
There are a lot of moving parts in the hibernate save and restore paths,
so I don't know exactly what caused the panic. Presumably, a FRAME_END
was executed without the corresponding FRAME_BEGIN, or vice versa. That
would corrupt the return address on the stack and would be consistent
with the details of the above panic.
[ rjw: One major problem is that by the time the FRAME_BEGIN in
restore_registers() is executed, the stack pointer value may not
be valid any more. Namely, the stack area pointed to by it
previously may have been overwritten by some image memory contents
and that page frame may now be used for whatever different purpose
it had been allocated for before hibernation. In that case, the
FRAME_BEGIN will corrupt that memory. ]
Instead of doing the frame pointer save/restore around the bounds of the
affected functions, just do it around the call to swsusp_save().
That has the same effect of ensuring that if swsusp_save() sleeps, the
frame pointers will be correct. It's also a much more obviously safe
way to do it than the original patch. And objtool still doesn't report
any warnings.
Fixes: ef0f3ed5a4 (x86/asm/power: Create stack frames in hibernate_asm_64.S)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=150021
Reported-by: Andre Reinke <andre.reinke@mailbox.org>
Tested-by: Andre Reinke <andre.reinke@mailbox.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4b703305d9 upstream.
Usually, after we have found the proper microcode blob for the current
machine, we stash it away for later use with save_microcode_in_initrd().
However, with builtin microcode which doesn't come from the initrd, we
don't call that function because CONFIG_BLK_DEV_INITRD=n and even if
set, we don't have a valid initrd.
In order to fix this, let's make save_microcode_in_initrd() an
fs_initcall which runs before rootfs_initcall() as this was the time it
was called previously through:
rootfs_initcall(populate_rootfs)
|-> free_initrd()
|-> free_initrd_mem()
|-> save_microcode_in_initrd()
Also, we make it run independently from initrd functionality being
present or not.
And since it is called in the microcode loader only now, we can also
make it static.
Reported-and-tested-by: Jim Bos <jim876@xs4all.nl>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1465225850-7352-3-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05eb6e7263 upstream.
Radix trees may be used not only for storing page cache pages, so
unconditionally accounting radix tree nodes to the current memory cgroup
is bad: if a radix tree node is used for storing data shared among
different cgroups we risk pinning dead memory cgroups forever.
So let's only account radix tree nodes if it was explicitly requested by
passing __GFP_ACCOUNT to INIT_RADIX_TREE. Currently, we only want to
account page cache entries, so mark mapping->page_tree so.
Fixes: 58e698af4c ("radix-tree: account radix_tree_node to memory cgroup")
Link: http://lkml.kernel.org/r/1470057188-7864-1-git-send-email-vdavydov@virtuozzo.com
Signed-off-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 86a574de45 upstream.
Don't allow RNDADDTOENTCNT or RNDADDENTROPY to accept a negative
entropy value. It doesn't make any sense to subtract from the entropy
counter, and it can trigger a warning:
random: negative entropy/overflow: pool input count -40000
------------[ cut here ]------------
WARNING: CPU: 3 PID: 6828 at drivers/char/random.c:670[< none
>] credit_entropy_bits+0x21e/0xad0 drivers/char/random.c:670
Modules linked in:
CPU: 3 PID: 6828 Comm: a.out Not tainted 4.7.0-rc4+ #4
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
ffffffff880b58e0 ffff88005dd9fcb0 ffffffff82cc838f ffffffff87158b40
fffffbfff1016b1c 0000000000000000 0000000000000000 ffffffff87158b40
ffffffff83283dae 0000000000000009 ffff88005dd9fcf8 ffffffff8136d27f
Call Trace:
[< inline >] __dump_stack lib/dump_stack.c:15
[<ffffffff82cc838f>] dump_stack+0x12e/0x18f lib/dump_stack.c:51
[<ffffffff8136d27f>] __warn+0x19f/0x1e0 kernel/panic.c:516
[<ffffffff8136d48c>] warn_slowpath_null+0x2c/0x40 kernel/panic.c:551
[<ffffffff83283dae>] credit_entropy_bits+0x21e/0xad0 drivers/char/random.c:670
[< inline >] credit_entropy_bits_safe drivers/char/random.c:734
[<ffffffff8328785d>] random_ioctl+0x21d/0x250 drivers/char/random.c:1546
[< inline >] vfs_ioctl fs/ioctl.c:43
[<ffffffff8185316c>] do_vfs_ioctl+0x18c/0xff0 fs/ioctl.c:674
[< inline >] SYSC_ioctl fs/ioctl.c:689
[<ffffffff8185405f>] SyS_ioctl+0x8f/0xc0 fs/ioctl.c:680
[<ffffffff86a995c0>] entry_SYSCALL_64_fastpath+0x23/0xc1
arch/x86/entry/entry_64.S:207
---[ end trace 5d4902b2ba842f1f ]---
This was triggered using the test program:
// autogenerated by syzkaller (http://github.com/google/syzkaller)
int main() {
int fd = open("/dev/random", O_RDWR);
int val = -5000;
ioctl(fd, RNDADDTOENTCNT, &val);
return 0;
}
It's harmless in that (a) only root can trigger it, and (b) after
complaining the code never does let the entropy count go negative, but
it's better to simply not allow this userspace from passing in a
negative entropy value altogether.
Google-Bug-Id: #29575089
Reported-By: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f626300a3e ]
tcp_select_initial_window() intends to advertise a window
scaling for the maximum possible window size. To do so,
it considers the maximum of net.ipv4.tcp_rmem[2] and
net.core.rmem_max as the only possible upper-bounds.
However, users with CAP_NET_ADMIN can use SO_RCVBUFFORCE
to set the socket's receive buffer size to values
larger than net.ipv4.tcp_rmem[2] and net.core.rmem_max.
Thus, SO_RCVBUFFORCE is effectively ignored by
tcp_select_initial_window().
To fix this, consider the maximum of net.ipv4.tcp_rmem[2],
net.core.rmem_max and socket's initial buffer space.
Fixes: b0573dea1f ("[NET]: Introduce SO_{SND,RCV}BUFFORCE socket options")
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Suggested-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e3a3b62601 ]
macsec_decrypt() is not called when validation is disabled and so
macsec_skb_cb(skb)->rx_sa is not set; but it is used later in
macsec_post_decrypt(), ensure that it's always initialized.
Fixes: c09440f7dc ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Beniamino Galvani <bgalvani@redhat.com>
Acked-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5fc382d875 ]
I was seeing a lot of these:
BUG: sleeping function called from invalid context at mm/slab.h:388
in_atomic(): 0, irqs_disabled(): 0, pid: 14971, name: trinity-c2
Preemption disabled at:[<ffffffff819bcd46>] rhashtable_walk_start+0x46/0x150
[<ffffffff81149abb>] preempt_count_add+0x1fb/0x280
[<ffffffff83295722>] _raw_spin_lock+0x12/0x40
[<ffffffff811aac87>] console_unlock+0x2f7/0x930
[<ffffffff811ab5bb>] vprintk_emit+0x2fb/0x520
[<ffffffff811aba6a>] vprintk_default+0x1a/0x20
[<ffffffff812c171a>] printk+0x94/0xb0
[<ffffffff811d6ed0>] print_stack_trace+0xe0/0x170
[<ffffffff8115835e>] ___might_sleep+0x3be/0x460
[<ffffffff81158490>] __might_sleep+0x90/0x1a0
[<ffffffff8139b823>] kmem_cache_alloc+0x153/0x1e0
[<ffffffff819bca1e>] rhashtable_walk_init+0xfe/0x2d0
[<ffffffff82ec64de>] sctp_transport_walk_start+0x1e/0x60
[<ffffffff82edd8ad>] sctp_transport_seq_start+0x4d/0x150
[<ffffffff8143a82b>] seq_read+0x27b/0x1180
[<ffffffff814f97fc>] proc_reg_read+0xbc/0x180
[<ffffffff813d471b>] __vfs_read+0xdb/0x610
[<ffffffff813d4d3a>] vfs_read+0xea/0x2d0
[<ffffffff813d615b>] SyS_pread64+0x11b/0x150
[<ffffffff8100334c>] do_syscall_64+0x19c/0x410
[<ffffffff832960a5>] return_from_SYSCALL_64+0x0/0x6a
[<ffffffffffffffff>] 0xffffffffffffffff
Apparently we always need to call rhashtable_walk_stop(), even when
rhashtable_walk_start() fails:
* rhashtable_walk_start - Start a hash table walk
* @iter: Hash table iterator
*
* Start a hash table walk. Note that we take the RCU lock in all
* cases including when we return an error. So you must always call
* rhashtable_walk_stop to clean up.
otherwise we never call rcu_read_unlock() and we get the splat above.
Fixes: 53fa1036 ("sctp: fix some rhashtable functions using in sctp proc/diag")
See-also: 53fa1036 ("sctp: fix some rhashtable functions using in sctp proc/diag")
See-also: f2dba9c6 ("rhashtable: Introduce rhashtable_walk_*")
Cc: Xin Long <lucien.xin@gmail.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: stable@vger.kernel.org
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ea06f71764 ]
Default kernel behavior is to delete IPv6 addresses on link
down, which entails deletion of the multicast and the
subnet-router anycast addresses. These deletions do not
happen with sysctl setting to keep global IPv6 addresses on
link down, so every link down/up causes an increment of the
anycast and multicast refcounts. These bogus refcounts may
stop these addrs from being removed on subsequent calls to
delete them. The solution is to leave the groups for the
multicast and subnet anycast on link down for the callflow
when global IPv6 addresses are kept.
Fixes: f1705ec197 ("net: ipv6: Make address flushing on ifdown optional")
Signed-off-by: Mike Manning <mmanning@brocade.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit baedbe5588 ]
Commit 8626c56c82 ("bridge: fix potential use-after-free when hook
returns QUEUE or STOLEN verdict") caused LLDP packets arriving through a
bridge port to be re-injected to the Rx path with skb->dev set to the
bridge device, but this breaks the lldpad daemon.
The lldpad daemon opens a packet socket with protocol set to ETH_P_LLDP
for any valid device on the system, which doesn't not include soft
devices such as bridge and VLAN.
Since packet sockets (ptype_base) are processed in the Rx path after the
Rx handler, LLDP packets with skb->dev set to the bridge device never
reach the lldpad daemon.
Fix this by making the bridge's Rx handler re-inject LLDP packets with
RX_HANDLER_PASS, which effectively restores the behaviour prior to the
mentioned commit.
This means netfilter will never receive LLDP packets coming through a
bridge port, as I don't see a way in which we can have okfn() consume
the packet without breaking existing behaviour. I've already carried out
a similar fix for STP packets in commit 56fae404fb ("bridge: Fix
incorrect re-injection of STP packets").
Fixes: 8626c56c82 ("bridge: fix potential use-after-free when hook returns QUEUE or STOLEN verdict")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1533e77315 ]
When using an IPoIB bond currently only active-backup mode is a valid
use case and this commit strengthens it.
Since commit 2ab82852a2 ("net/bonding: Enable bonding to enslave
netdevices not supporting set_mac_address()") was introduced till
4.7-rc1, IPoIB didn't support the set_mac_address ndo, and hence the
fail over mac policy always applied to IPoIB bonds.
With the introduction of commit 492a7e67ff ("IB/IPoIB: Allow setting
the device address"), that doesn't hold and practically IPoIB bonds are
broken as of that. To fix it, lets go to fail over mac if the device
doesn't support the ndo OR this is IPoIB device.
As a by-product, this commit also prevents a stack corruption which
occurred when trying to copy 20 bytes (IPoIB) device address
to a sockaddr struct that has only 16 bytes of storage.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ba66bbe548 ]
After a612769774 ("udp: prevent bugcheck if filter truncates packet
too much"), there followed various other fixes for similar cases such
as f4979fcea7 ("rose: limit sk_filter trim to payload").
Latter introduced a new helper sk_filter_trim_cap(), where we can pass
the trim limit directly to the socket filter handling. Make use of it
here as well with sizeof(struct udphdr) as lower cap limit and drop the
extra skb->len test in UDP's input path.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1892c3776 upstream.
file_remove_privs() is called with inode lock on file_inode(), which
proceeds to calling notify_change() on file->f_path.dentry. Which triggers
the WARN_ON_ONCE(!inode_is_locked(inode)) in addition to deadlocking later
when ovl_setattr tries to lock the underlying inode again.
Fix this mess by not mixing the layers, but doing everything on underlying
dentry/inode.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Fixes: 07a2daab49 ("ovl: Copy up underlying inode's ->i_mode to overlay inode")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 10eec60ce7 upstream.
This prevents a double-fetch from user space that can lead to to an
undersized allocation and heap overflow.
Fixes: 54dbc15172 ("vfs: hoist the btrfs deduplication ioctl to the vfs")
Signed-off-by: Scott Bauer <sbauer@plzdonthack.me>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7bc9491645 upstream.
Although the extent tree depth of 5 should enough be for the worst
case of 2*32 extents of length 1, the extent tree code does not
currently to merge nodes which are less than half-full with a sibling
node, or to shrink the tree depth if possible. So it's possible, at
least in theory, for the tree depth to be greater than 5. However,
even in the worst case, a tree depth of 32 is highly unlikely, and if
the file system is maliciously corrupted, an insanely large eh_depth
can cause memory allocation failures that will trigger kernel warnings
(here, eh_depth = 65280):
JBD2: ext4.exe wants too many credits credits:195849 rsv_credits:0 max:256
------------[ cut here ]------------
WARNING: CPU: 0 PID: 50 at fs/jbd2/transaction.c:293 start_this_handle+0x569/0x580
CPU: 0 PID: 50 Comm: ext4.exe Not tainted 4.7.0-rc5+ #508
Stack:
604a8947 625badd8 0002fd09 00000000
60078643 00000000 62623910 601bf9bc
62623970 6002fc84 626239b0 900000125
Call Trace:
[<6001c2dc>] show_stack+0xdc/0x1a0
[<601bf9bc>] dump_stack+0x2a/0x2e
[<6002fc84>] __warn+0x114/0x140
[<6002fdff>] warn_slowpath_null+0x1f/0x30
[<60165829>] start_this_handle+0x569/0x580
[<60165d4e>] jbd2__journal_start+0x11e/0x220
[<60146690>] __ext4_journal_start_sb+0x60/0xa0
[<60120a81>] ext4_truncate+0x131/0x3a0
[<60123677>] ext4_setattr+0x757/0x840
[<600d5d0f>] notify_change+0x16f/0x2a0
[<600b2b16>] do_truncate+0x76/0xc0
[<600c3e56>] path_openat+0x806/0x1300
[<600c55c9>] do_filp_open+0x89/0xf0
[<600b4074>] do_sys_open+0x134/0x1e0
[<600b4140>] SyS_open+0x20/0x30
[<6001ea68>] handle_syscall+0x88/0x90
[<600295fd>] userspace+0x3fd/0x500
[<6001ac55>] fork_handler+0x85/0x90
---[ end trace 08b0b88b6387a244 ]---
[ Commit message modified and the extent tree depath check changed
from 5 to 32 -- tytso ]
Cc: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-16 09:34:57 +02:00
1515 changed files with 302220 additions and 6743 deletions
// s08-spi<n>-<m>-int-gpio - integer, enables interrupts on a single MCP23S08 device on SPI<n>, CS#<m>, specifies the GPIO pin to which INT output is connected.
// s17-spi<n>-<m>-int-gpio - integer, enables mirrored interrupts on a single MCP23S17 device on SPI<n>, CS#<m>, specifies the GPIO pin to which either INTA or INTB output is connected.
//
// If devices are present on SPI1 or SPI2, those interfaces must be enabled with one of the spi1-1/2/3cs and/or spi2-1/2/3cs overlays.
// If interrupts are enabled for a device on a given CS# on a SPI bus, that device must be the only one present on that SPI bus/CS#.
//
// Example 1: A single MCP23S17 device on SPI0, CS#0 with its SPI addr set to 0 and INTA output connected to GPIO25:
// Example 2: Two MCP23S08 devices on SPI1, CS#0 with their addrs set to 2 and 3. Three MCP23S17 devices on SPI1, CS#1 with their addrs set to 0, 1 and 7:
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
