Merge remote-tracking branch 'stable/linux-4.4.y' into rpi-4.4.y

commit 72fd50e14e upstream.

The req_canceled() callback is used by tpm_transmit() periodically to
check whether the request has been canceled while it is receiving a
response from the TPM.

The TPM_CRB_CTRL_CANCEL register was cleared already in the crb_cancel
callback, which has two consequences:

* Cancel might not happen.
* req_canceled() always returns zero.

A better place to clear the register is when starting to send a new
command. The behavior of TPM_CRB_CTRL_CANCEL is described in the
section 5.5.3.6 of the PTP specification.

Fixes: 30fc8d138e ("tpm: TPM 2.0 CRB Interface")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Documentation/ABI/testing/sysfs-bus-iio-proximity-as3935

@@ -1,4 +1,4 @@
-What		/sys/bus/iio/devices/iio:deviceX/in_proximity_raw
+What		/sys/bus/iio/devices/iio:deviceX/in_proximity_input
 Date:		March 2014
 KernelVersion:	3.15
 Contact:	Matt Ranostay <mranostay@gmail.com>

Documentation/devicetree/bindings/ata/ahci-platform.txt

@@ -30,6 +30,10 @@ Optional properties:
 - target-supply     : regulator for SATA target power
 - phys              : reference to the SATA PHY node
 - phy-names         : must be "sata-phy"
+- ports-implemented : Mask that indicates which ports that the HBA supports
+		      are available for software to use. Useful if PORTS_IMPL
+		      is not programmed by the BIOS, which is true with
+		      some embedded SOC's.
 
 Required properties when using sub-nodes:
 - #address-cells    : number of cells to encode an address

Documentation/devicetree/bindings/clock/brcm,bcm2835-cprman.txt

@@ -16,7 +16,17 @@ Required properties:
 - #clock-cells:	Should be <1>. The permitted clock-specifier values can be
 		  found in include/dt-bindings/clock/bcm2835.h
 - reg:		Specifies base physical address and size of the registers
-- clocks:	The external oscillator clock phandle
+- clocks:	phandles to the parent clocks used as input to the module, in
+		  the following order:
+
+		  - External oscillator
+		  - DSI1 byte clock
+		  - DSI1 DDR2 clock
+		  - DSI1 DDR clock
+
+		  Only external oscillator is required.  The DSI clocks may
+		  not be present, in which case their children will be
+		  unusable.
 
 Example:
 

Documentation/devicetree/bindings/clock/imx35-clock.txt

@@ -94,6 +94,7 @@ clocks and IDs.
 	csi_sel			79
 	iim_gate		80
 	gpu2d_gate		81
+	ckli_gate		82
 
 Examples:
 

Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt

@@ -35,6 +35,22 @@ Optional properties for HDMI:
 		  as an interrupt/status bit in the HDMI controller
 		  itself).  See bindings/pinctrl/brcm,bcm2835-gpio.txt
 
+Required properties for DPI:
+- compatible:	Should be "brcm,bcm2835-dpi"
+- reg:		Physical base address and length of the registers
+- clocks:	a) core: The core clock the unit runs on
+		b) pixel: The pixel clock that feeds the pixelvalve
+- port:		Port node with a single endpoint connecting to the panel
+		  device, as defined in [1]
+
+Required properties for V3D:
+- compatible:	Should be "brcm,bcm2835-v3d"
+- reg:		Physical base address and length of the V3D's registers
+- interrupts:	The interrupt number
+		  See bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt
+
+[1] Documentation/devicetree/bindings/media/video-interfaces.txt
+
 Example:
 pixelvalve@7e807000 {
 	compatible = "brcm,bcm2835-pixelvalve2";
@@ -60,6 +76,38 @@ hdmi: hdmi@7e902000 {
 	clock-names = "pixel", "hdmi";
 };
 
+dpi: dpi@7e208000 {
+	compatible = "brcm,bcm2835-dpi";
+	reg = <0x7e208000 0x8c>;
+	clocks = <&clocks BCM2835_CLOCK_VPU>,
+	         <&clocks BCM2835_CLOCK_DPI>;
+	clock-names = "core", "pixel";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	port {
+		dpi_out: endpoint@0 {
+			remote-endpoint = <&panel_in>;
+		};
+	};
+};
+
+v3d: v3d@7ec00000 {
+	compatible = "brcm,bcm2835-v3d";
+	reg = <0x7ec00000 0x1000>;
+	interrupts = <1 10>;
+};
+
 vc4: gpu {
 	compatible = "brcm,bcm2835-vc4";
 };
+
+panel: panel {
+	compatible = "ontat,yx700wv03", "simple-panel";
+
+	port {
+		panel_in: endpoint {
+			remote-endpoint = <&dpi_out>;
+		};
+	};
+};

Documentation/devicetree/bindings/display/panel/ontat,yx700wv03.txt

@@ -0,0 +1,7 @@
+On Tat Industrial Company 7" DPI TFT panel.
+
+Required properties:
+- compatible: should be "ontat,yx700wv03"
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.

Documentation/devicetree/bindings/iio/adc/rockchip-saradc.txt

@@ -12,6 +12,11 @@ Required properties:
 - vref-supply: The regulator supply ADC reference voltage.
 - #io-channel-cells: Should be 1, see ../iio-bindings.txt
 
+Optional properties:
+- resets: Must contain an entry for each entry in reset-names if need support
+	  this option. See ../reset/reset.txt for details.
+- reset-names: Must include the name "saradc-apb".
+
 Example:
 	saradc: saradc@2006c000 {
 		compatible = "rockchip,saradc";
@@ -19,6 +24,8 @@ Example:
 		interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&cru SCLK_SARADC>, <&cru PCLK_SARADC>;
 		clock-names = "saradc", "apb_pclk";
+		resets = <&cru SRST_SARADC>;
+		reset-names = "saradc-apb";
 		#io-channel-cells = <1>;
 		vref-supply = <&vcc18>;
 	};

Documentation/devicetree/bindings/net/microchip,enc28j60.txt

@@ -0,0 +1,59 @@
+* Microchip ENC28J60
+
+This is a standalone 10 MBit ethernet controller with SPI interface.
+
+For each device connected to a SPI bus, define a child node within
+the SPI master node.
+
+Required properties:
+- compatible: Should be "microchip,enc28j60"
+- reg: Specify the SPI chip select the ENC28J60 is wired to
+- interrupt-parent: Specify the phandle of the source interrupt, see interrupt
+                    binding documentation for details. Usually this is the GPIO bank
+                    the interrupt line is wired to.
+- interrupts: Specify the interrupt index within the interrupt controller (referred
+              to above in interrupt-parent) and interrupt type. The ENC28J60 natively
+              generates falling edge interrupts, however, additional board logic
+              might invert the signal.
+- pinctrl-names: List of assigned state names, see pinctrl binding documentation.
+- pinctrl-0: List of phandles to configure the GPIO pin used as interrupt line,
+             see also generic and your platform specific pinctrl binding
+             documentation.
+
+Optional properties:
+- spi-max-frequency: Maximum frequency of the SPI bus when accessing the ENC28J60.
+  According to the ENC28J80 datasheet, the chip allows a maximum of 20 MHz, however,
+  board designs may need to limit this value.
+- local-mac-address: See ethernet.txt in the same directory.
+
+
+Example (for NXP i.MX28 with pin control stuff for GPIO irq):
+
+        ssp2: ssp@80014000 {
+                compatible = "fsl,imx28-spi";
+                pinctrl-names = "default";
+                pinctrl-0 = <&spi2_pins_b &spi2_sck_cfg>;
+                status = "okay";
+
+                enc28j60: ethernet@0 {
+                        compatible = "microchip,enc28j60";
+                        pinctrl-names = "default";
+                        pinctrl-0 = <&enc28j60_pins>;
+                        reg = <0>;
+                        interrupt-parent = <&gpio3>;
+                        interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
+                        spi-max-frequency = <12000000>;
+                };
+        };
+
+        pinctrl@80018000 {
+                enc28j60_pins: enc28j60_pins@0 {
+                        reg = <0>;
+                        fsl,pinmux-ids = <
+                                MX28_PAD_AUART0_RTS__GPIO_3_3    /* Interrupt */
+                        >;
+                        fsl,drive-strength = <MXS_DRIVE_4mA>;
+                        fsl,voltage = <MXS_VOLTAGE_HIGH>;
+                        fsl,pull-up = <MXS_PULL_DISABLE>;
+                };
+        };

Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt

@@ -81,9 +81,9 @@ pm8916:
 	l14, l15, l16, l17, l18
 
 pm8941:
-	s1, s2, s3, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13, l14,
-	l15, l16, l17, l18, l19, l20, l21, l22, l23, l24, lvs1, lvs2, lvs3,
-	mvs1, mvs2
+	s1, s2, s3, s4, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13,
+	l14, l15, l16, l17, l18, l19, l20, l21, l22, l23, l24, lvs1, lvs2, lvs3,
+	5vs1, 5vs2
 
 The content of each sub-node is defined by the standard binding for regulators -
 see regulator.txt - with additional custom properties described below:

Documentation/filesystems/proc.txt

@@ -346,7 +346,7 @@ address           perms offset  dev   inode      pathname
 a7cb1000-a7cb2000 ---p 00000000 00:00 0
 a7cb2000-a7eb2000 rw-p 00000000 00:00 0
 a7eb2000-a7eb3000 ---p 00000000 00:00 0
-a7eb3000-a7ed5000 rw-p 00000000 00:00 0          [stack:1001]
+a7eb3000-a7ed5000 rw-p 00000000 00:00 0
 a7ed5000-a8008000 r-xp 00000000 03:00 4222       /lib/libc.so.6
 a8008000-a800a000 r--p 00133000 03:00 4222       /lib/libc.so.6
 a800a000-a800b000 rw-p 00135000 03:00 4222       /lib/libc.so.6
@@ -378,7 +378,6 @@ is not associated with a file:
 
  [heap]                   = the heap of the program
  [stack]                  = the stack of the main process
- [stack:1001]             = the stack of the thread with tid 1001
  [vdso]                   = the "virtual dynamic shared object",
                             the kernel system call handler
 
@@ -386,10 +385,8 @@ is not associated with a file:
 
 The /proc/PID/task/TID/maps is a view of the virtual memory from the viewpoint
 of the individual tasks of a process. In this file you will see a mapping marked
-as [stack] if that task sees it as a stack. This is a key difference from the
-content of /proc/PID/maps, where you will see all mappings that are being used
-as stack by all of those tasks. Hence, for the example above, the task-level
-map, i.e. /proc/PID/task/TID/maps for thread 1001 will look like this:
+as [stack] if that task sees it as a stack. Hence, for the example above, the
+task-level map, i.e. /proc/PID/task/TID/maps for thread 1001 will look like this:
 
 08048000-08049000 r-xp 00000000 03:00 8312       /opt/test
 08049000-0804a000 rw-p 00001000 03:00 8312       /opt/test

Documentation/mic/mpssd/mpssd.c

@@ -1538,9 +1538,9 @@ set_cmdline(struct mic_info *mic)
 
 	len = snprintf(buffer, PATH_MAX,
 		"clocksource=tsc highres=off nohz=off ");
-	len += snprintf(buffer + len, PATH_MAX,
+	len += snprintf(buffer + len, PATH_MAX - len,
 		"cpufreq_on;corec6_off;pc3_off;pc6_off ");
-	len += snprintf(buffer + len, PATH_MAX,
+	len += snprintf(buffer + len, PATH_MAX - len,
 		"ifcfg=static;address,172.31.%d.1;netmask,255.255.255.0",
 		mic->id + 1);
 

Documentation/module-signing.txt

@@ -271,3 +271,9 @@ Since the private key is used to sign modules, viruses and malware could use
 the private key to sign modules and compromise the operating system.  The
 private key must be either destroyed or moved to a secure location and not kept
 in the root node of the kernel source tree.
+
+If you use the same private key to sign modules for multiple kernel
+configurations, you must ensure that the module version information is
+sufficient to prevent loading a module into a different kernel.  Either
+set CONFIG_MODVERSIONS=y or ensure that each configuration has a different
+kernel release string by changing EXTRAVERSION or CONFIG_LOCALVERSION.

Documentation/pinctrl.txt

@@ -831,7 +831,7 @@ separate memory range only intended for GPIO driving, and the register
 range dealing with pin config and pin multiplexing get placed into a
 different memory range and a separate section of the data sheet.
 
-A flag "strict" in struct pinctrl_desc is available to check and deny
+A flag "strict" in struct pinmux_ops is available to check and deny
 simultaneous access to the same pin from GPIO and pin multiplexing
 consumers on hardware of this type. The pinctrl driver should set this flag
 accordingly.

Documentation/scsi/scsi_eh.txt

@@ -263,19 +263,23 @@ scmd->allowed.
 
  3. scmd recovered
     ACTION: scsi_eh_finish_cmd() is invoked to EH-finish scmd
-	- shost->host_failed--
 	- clear scmd->eh_eflags
 	- scsi_setup_cmd_retry()
 	- move from local eh_work_q to local eh_done_q
     LOCKING: none
+    CONCURRENCY: at most one thread per separate eh_work_q to
+		 keep queue manipulation lockless
 
  4. EH completes
     ACTION: scsi_eh_flush_done_q() retries scmds or notifies upper
-	    layer of failure.
+	    layer of failure. May be called concurrently but must have
+	    a no more than one thread per separate eh_work_q to
+	    manipulate the queue locklessly
 	- scmd is removed from eh_done_q and scmd->eh_entry is cleared
 	- if retry is necessary, scmd is requeued using
           scsi_queue_insert()
 	- otherwise, scsi_finish_command() is invoked for scmd
+	- zero shost->host_failed
     LOCKING: queue or finish function performs appropriate locking
 
 

Documentation/serial/tty.txt

@@ -213,9 +213,6 @@ TTY_IO_ERROR		If set, causes all subsequent userspace read/write
 
 TTY_OTHER_CLOSED	Device is a pty and the other side has closed.
 
-TTY_OTHER_DONE		Device is a pty and the other side has closed and
-			all pending input processing has been completed.
-
 TTY_NO_WRITE_SPLIT	Prevent driver from splitting up writes into
 			smaller chunks.
 

Documentation/sysctl/fs.txt

@@ -32,6 +32,8 @@ Currently, these files are in /proc/sys/fs:
 - nr_open
 - overflowuid
 - overflowgid
+- pipe-user-pages-hard
+- pipe-user-pages-soft
 - protected_hardlinks
 - protected_symlinks
 - suid_dumpable
@@ -159,6 +161,27 @@ The default is 65534.
 
 ==============================================================
 
+pipe-user-pages-hard:
+
+Maximum total number of pages a non-privileged user may allocate for pipes.
+Once this limit is reached, no new pipes may be allocated until usage goes
+below the limit again. When set to 0, no limit is applied, which is the default
+setting.
+
+==============================================================
+
+pipe-user-pages-soft:
+
+Maximum total number of pages a non-privileged user may allocate for pipes
+before the pipe size gets limited to a single page. Once this limit is reached,
+new pipes will be limited to a single page in size for this user in order to
+limit total memory usage, and trying to increase them using fcntl() will be
+denied until usage goes below the limit again. The default value allows to
+allocate up to 1024 pipes at their default size. When set to 0, no limit is
+applied.
+
+==============================================================
+
 protected_hardlinks:
 
 A long-standing class of security issues is the hardlink-based

Documentation/x86/pat.txt

@@ -196,3 +196,35 @@ Another, more verbose way of getting PAT related debug messages is with
 "debugpat" boot parameter. With this parameter, various debug messages are
 printed to dmesg log.
 
+PAT Initialization
+------------------
+
+The following table describes how PAT is initialized under various
+configurations. The PAT MSR must be updated by Linux in order to support WC
+and WT attributes. Otherwise, the PAT MSR has the value programmed in it
+by the firmware. Note, Xen enables WC attribute in the PAT MSR for guests.
+
+ MTRR PAT   Call Sequence               PAT State  PAT MSR
+ =========================================================
+ E    E     MTRR -> PAT init            Enabled    OS
+ E    D     MTRR -> PAT init            Disabled    -
+ D    E     MTRR -> PAT disable         Disabled   BIOS
+ D    D     MTRR -> PAT disable         Disabled    -
+ -    np/E  PAT  -> PAT disable         Disabled   BIOS
+ -    np/D  PAT  -> PAT disable         Disabled    -
+ E    !P/E  MTRR -> PAT init            Disabled   BIOS
+ D    !P/E  MTRR -> PAT disable         Disabled   BIOS
+ !M   !P/E  MTRR stub -> PAT disable    Disabled   BIOS
+
+ Legend
+ ------------------------------------------------
+ E         Feature enabled in CPU
+ D	   Feature disabled/unsupported in CPU
+ np	   "nopat" boot option specified
+ !P	   CONFIG_X86_PAT option unset
+ !M	   CONFIG_MTRR option unset
+ Enabled   PAT state set to enabled
+ Disabled  PAT state set to disabled
+ OS        PAT initializes PAT MSR with OS setting
+ BIOS      PAT keeps PAT MSR with BIOS setting
+

MAINTAINERS

@@ -4097,8 +4097,8 @@ F:	Documentation/efi-stub.txt
 F:	arch/ia64/kernel/efi.c
 F:	arch/x86/boot/compressed/eboot.[ch]
 F:	arch/x86/include/asm/efi.h
-F:	arch/x86/platform/efi/*
-F:	drivers/firmware/efi/*
+F:	arch/x86/platform/efi/
+F:	drivers/firmware/efi/
 F:	include/linux/efi*.h
 
 EFI VARIABLE FILESYSTEM

Makefile

@@ -1,6 +1,6 @@
 VERSION = 4
 PATCHLEVEL = 4
-SUBLEVEL = 9
+SUBLEVEL = 26
 EXTRAVERSION =
 NAME = Blurry Fish Butt
 
@@ -128,6 +128,10 @@ _all:
 # Cancel implicit rules on top Makefile
 $(CURDIR)/Makefile Makefile: ;
 
+ifneq ($(words $(subst :, ,$(CURDIR))), 1)
+  $(error main directory cannot contain spaces nor colons)
+endif
+
 ifneq ($(KBUILD_OUTPUT),)
 # Invoke a second make in the output directory, passing relevant variables
 # check that the output directory actually exists
@@ -364,7 +368,7 @@ AFLAGS_MODULE   =
 LDFLAGS_MODULE  =
 CFLAGS_KERNEL	=
 AFLAGS_KERNEL	=
-CFLAGS_GCOV	= -fprofile-arcs -ftest-coverage
+CFLAGS_GCOV	= -fprofile-arcs -ftest-coverage -fno-tree-loop-im
 
 
 # Use USERINCLUDE when you must reference the UAPI directories only.
@@ -495,6 +499,12 @@ ifeq ($(KBUILD_EXTMOD),)
                 endif
         endif
 endif
+# install and module_install need also be processed one by one
+ifneq ($(filter install,$(MAKECMDGOALS)),)
+        ifneq ($(filter modules_install,$(MAKECMDGOALS)),)
+	        mixed-targets := 1
+        endif
+endif
 
 ifeq ($(mixed-targets),1)
 # ===========================================================================
@@ -606,12 +616,17 @@ ARCH_CFLAGS :=
 include arch/$(SRCARCH)/Makefile
 
 KBUILD_CFLAGS	+= $(call cc-option,-fno-delete-null-pointer-checks,)
+KBUILD_CFLAGS	+= $(call cc-disable-warning,maybe-uninitialized,)
 
 ifdef CONFIG_CC_OPTIMIZE_FOR_SIZE
-KBUILD_CFLAGS	+= -Os $(call cc-disable-warning,maybe-uninitialized,)
+KBUILD_CFLAGS	+= -Os
+else
+ifdef CONFIG_PROFILE_ALL_BRANCHES
+KBUILD_CFLAGS	+= -O2
 else
 KBUILD_CFLAGS   += -O2
 endif
+endif
 
 # Tell gcc to never replace conditional load with a non-conditional one
 KBUILD_CFLAGS	+= $(call cc-option,--param=allow-store-data-races=0)
@@ -682,9 +697,10 @@ KBUILD_CFLAGS += $(call cc-option, -mno-global-merge,)
 KBUILD_CFLAGS += $(call cc-option, -fcatch-undefined-behavior)
 else
 
-# This warning generated too much noise in a regular build.
-# Use make W=1 to enable this warning (see scripts/Makefile.build)
+# These warnings generated too much noise in a regular build.
+# Use make W=1 to enable them (see scripts/Makefile.build)
 KBUILD_CFLAGS += $(call cc-disable-warning, unused-but-set-variable)
+KBUILD_CFLAGS += $(call cc-disable-warning, unused-const-variable)
 endif
 
 ifdef CONFIG_FRAME_POINTER
@@ -1259,7 +1275,7 @@ help:
 	@echo  '  firmware_install- Install all firmware to INSTALL_FW_PATH'
 	@echo  '                    (default: $$(INSTALL_MOD_PATH)/lib/firmware)'
 	@echo  '  dir/            - Build all files in dir and below'
-	@echo  '  dir/file.[oisS] - Build specified target only'
+	@echo  '  dir/file.[ois]  - Build specified target only'
 	@echo  '  dir/file.lst    - Build specified mixed source/assembly target only'
 	@echo  '                    (requires a recent binutils and recent build (System.map))'
 	@echo  '  dir/file.ko     - Build module including final link'
@@ -1499,11 +1515,11 @@ image_name:
 # Clear a bunch of variables before executing the submake
 tools/: FORCE
 	$(Q)mkdir -p $(objtree)/tools
-	$(Q)$(MAKE) LDFLAGS= MAKEFLAGS="$(filter --j% -j,$(MAKEFLAGS))" O=$(O) subdir=tools -C $(src)/tools/
+	$(Q)$(MAKE) LDFLAGS= MAKEFLAGS="$(filter --j% -j,$(MAKEFLAGS))" O=$(shell cd $(objtree) && /bin/pwd) subdir=tools -C $(src)/tools/
 
 tools/%: FORCE
 	$(Q)mkdir -p $(objtree)/tools
-	$(Q)$(MAKE) LDFLAGS= MAKEFLAGS="$(filter --j% -j,$(MAKEFLAGS))" O=$(O) subdir=tools -C $(src)/tools/ $*
+	$(Q)$(MAKE) LDFLAGS= MAKEFLAGS="$(filter --j% -j,$(MAKEFLAGS))" O=$(shell cd $(objtree) && /bin/pwd) subdir=tools -C $(src)/tools/ $*
 
 # Single targets
 # ---------------------------------------------------------------------------

arch/alpha/include/asm/uaccess.h

@@ -371,14 +371,6 @@ __copy_tofrom_user_nocheck(void *to, const void *from, long len)
 	return __cu_len;
 }
 
-extern inline long
-__copy_tofrom_user(void *to, const void *from, long len, const void __user *validate)
-{
-	if (__access_ok((unsigned long)validate, len, get_fs()))
-		len = __copy_tofrom_user_nocheck(to, from, len);
-	return len;
-}
-
 #define __copy_to_user(to, from, n)					\
 ({									\
 	__chk_user_ptr(to);						\
@@ -393,17 +385,22 @@ __copy_tofrom_user(void *to, const void *from, long len, const void __user *vali
 #define __copy_to_user_inatomic __copy_to_user
 #define __copy_from_user_inatomic __copy_from_user
 
-
 extern inline long
 copy_to_user(void __user *to, const void *from, long n)
 {
-	return __copy_tofrom_user((__force void *)to, from, n, to);
+	if (likely(__access_ok((unsigned long)to, n, get_fs())))
+		n = __copy_tofrom_user_nocheck((__force void *)to, from, n);
+	return n;
 }
 
 extern inline long
 copy_from_user(void *to, const void __user *from, long n)
 {
-	return __copy_tofrom_user(to, (__force void *)from, n, from);
+	if (likely(__access_ok((unsigned long)from, n, get_fs())))
+		n = __copy_tofrom_user_nocheck(to, (__force void *)from, n);
+	else
+		memset(to, 0, n);
+	return n;
 }
 
 extern void __do_clear_user(void);

arch/arc/Kconfig

@@ -387,7 +387,7 @@ config ARC_HAS_LLSC
 
 config ARC_STAR_9000923308
 	bool "Workaround for llock/scond livelock"
-	default y
+	default n
 	depends on ISA_ARCV2 && SMP && ARC_HAS_LLSC
 
 config ARC_HAS_SWAPE

arch/arc/Makefile

@@ -18,6 +18,20 @@ cflags-y	+= -fno-common -pipe -fno-builtin -D__linux__
 cflags-$(CONFIG_ISA_ARCOMPACT)	+= -mA7
 cflags-$(CONFIG_ISA_ARCV2)	+= -mcpu=archs
 
+is_700 = $(shell $(CC) -dM -E - < /dev/null | grep -q "ARC700" && echo 1 || echo 0)
+
+ifdef CONFIG_ISA_ARCOMPACT
+ifeq ($(is_700), 0)
+    $(error Toolchain not configured for ARCompact builds)
+endif
+endif
+
+ifdef CONFIG_ISA_ARCV2
+ifeq ($(is_700), 1)
+    $(error Toolchain not configured for ARCv2 builds)
+endif
+endif
+
 ifdef CONFIG_ARC_CURR_IN_REG
 # For a global register defintion, make sure it gets passed to every file
 # We had a customer reported bug where some code built in kernel was NOT using
@@ -48,8 +62,6 @@ endif
 
 endif
 
-cflags-$(CONFIG_ARC_DW2_UNWIND)		+= -fasynchronous-unwind-tables
-
 # By default gcc 4.8 generates dwarf4 which kernel unwinder can't grok
 ifeq ($(atleast_gcc48),y)
 cflags-$(CONFIG_ARC_DW2_UNWIND)		+= -gdwarf-2

arch/arc/include/asm/arcregs.h

@@ -374,12 +374,6 @@ static inline int is_isa_arcompact(void)
 	return IS_ENABLED(CONFIG_ISA_ARCOMPACT);
 }
 
-#if defined(CONFIG_ISA_ARCOMPACT) && !defined(_CPU_DEFAULT_A7)
-#error "Toolchain not configured for ARCompact builds"
-#elif defined(CONFIG_ISA_ARCV2) && !defined(_CPU_DEFAULT_HS)
-#error "Toolchain not configured for ARCv2 builds"
-#endif
-
 #endif /* __ASEMBLY__ */
 
 #endif /* _ASM_ARC_ARCREGS_H */

arch/arc/include/asm/entry.h

@@ -142,7 +142,7 @@
 
 #ifdef CONFIG_ARC_CURR_IN_REG
 	; Retrieve orig r25 and save it with rest of callee_regs
-	ld.as   r12, [r12, PT_user_r25]
+	ld	r12, [r12, PT_user_r25]
 	PUSH	r12
 #else
 	PUSH	r25
@@ -198,7 +198,7 @@
 
 	; SP is back to start of pt_regs
 #ifdef CONFIG_ARC_CURR_IN_REG
-	st.as   r12, [sp, PT_user_r25]
+	st	r12, [sp, PT_user_r25]
 #endif
 .endm
 

arch/arc/include/asm/io.h

@@ -13,6 +13,15 @@
 #include <asm/byteorder.h>
 #include <asm/page.h>
 
+#ifdef CONFIG_ISA_ARCV2
+#include <asm/barrier.h>
+#define __iormb()		rmb()
+#define __iowmb()		wmb()
+#else
+#define __iormb()		do { } while (0)
+#define __iowmb()		do { } while (0)
+#endif
+
 extern void __iomem *ioremap(unsigned long physaddr, unsigned long size);
 extern void __iomem *ioremap_prot(phys_addr_t offset, unsigned long size,
 				  unsigned long flags);
@@ -22,6 +31,15 @@ extern void iounmap(const void __iomem *addr);
 #define ioremap_wc(phy, sz)		ioremap(phy, sz)
 #define ioremap_wt(phy, sz)		ioremap(phy, sz)
 
+/*
+ * io{read,write}{16,32}be() macros
+ */
+#define ioread16be(p)		({ u16 __v = be16_to_cpu((__force __be16)__raw_readw(p)); __iormb(); __v; })
+#define ioread32be(p)		({ u32 __v = be32_to_cpu((__force __be32)__raw_readl(p)); __iormb(); __v; })
+
+#define iowrite16be(v,p)	({ __iowmb(); __raw_writew((__force u16)cpu_to_be16(v), p); })
+#define iowrite32be(v,p)	({ __iowmb(); __raw_writel((__force u32)cpu_to_be32(v), p); })
+
 /* Change struct page to physical address */
 #define page_to_phys(page)		(page_to_pfn(page) << PAGE_SHIFT)
 
@@ -99,15 +117,6 @@ static inline void __raw_writel(u32 w, volatile void __iomem *addr)
 
 }
 
-#ifdef CONFIG_ISA_ARCV2
-#include <asm/barrier.h>
-#define __iormb()		rmb()
-#define __iowmb()		wmb()
-#else
-#define __iormb()		do { } while (0)
-#define __iowmb()		do { } while (0)
-#endif
-
 /*
  * MMIO can also get buffered/optimized in micro-arch, so barriers needed
  * Based on ARM model for the typical use case

arch/arc/include/asm/irqflags-compact.h

@@ -188,10 +188,10 @@ static inline int arch_irqs_disabled(void)
 .endm
 
 .macro IRQ_ENABLE  scratch
+	TRACE_ASM_IRQ_ENABLE
 	lr	\scratch, [status32]
 	or	\scratch, \scratch, (STATUS_E1_MASK | STATUS_E2_MASK)
 	flag	\scratch
-	TRACE_ASM_IRQ_ENABLE
 .endm
 
 #endif	/* __ASSEMBLY__ */

arch/arc/include/asm/pgtable.h

@@ -110,7 +110,7 @@
 #define ___DEF (_PAGE_PRESENT | _PAGE_CACHEABLE)
 
 /* Set of bits not changed in pte_modify */
-#define _PAGE_CHG_MASK	(PAGE_MASK | _PAGE_ACCESSED | _PAGE_DIRTY)
+#define _PAGE_CHG_MASK	(PAGE_MASK | _PAGE_ACCESSED | _PAGE_DIRTY | _PAGE_SPECIAL)
 
 /* More Abbrevaited helpers */
 #define PAGE_U_NONE     __pgprot(___DEF)
@@ -277,8 +277,7 @@ static inline void pmd_set(pmd_t *pmdp, pte_t *ptep)
 
 #define mk_pte(page, prot)	pfn_pte(page_to_pfn(page), prot)
 #define pte_pfn(pte)		(pte_val(pte) >> PAGE_SHIFT)
-#define pfn_pte(pfn, prot)	(__pte(((pte_t)(pfn) << PAGE_SHIFT) | \
-				 pgprot_val(prot)))
+#define pfn_pte(pfn, prot)	(__pte(((pfn) << PAGE_SHIFT) | pgprot_val(prot)))
 #define __pte_index(addr)	(((addr) >> PAGE_SHIFT) & (PTRS_PER_PTE - 1))
 
 /*

arch/arc/include/asm/uaccess.h

@@ -83,7 +83,10 @@
 	"2:	;nop\n"				\
 	"	.section .fixup, \"ax\"\n"	\
 	"	.align 4\n"			\
-	"3:	mov %0, %3\n"			\
+	"3:	# return -EFAULT\n"		\
+	"	mov %0, %3\n"			\
+	"	# zero out dst ptr\n"		\
+	"	mov %1,  0\n"			\
 	"	j   2b\n"			\
 	"	.previous\n"			\
 	"	.section __ex_table, \"a\"\n"	\
@@ -101,7 +104,11 @@
 	"2:	;nop\n"				\
 	"	.section .fixup, \"ax\"\n"	\
 	"	.align 4\n"			\
-	"3:	mov %0, %3\n"			\
+	"3:	# return -EFAULT\n"		\
+	"	mov %0, %3\n"			\
+	"	# zero out dst ptr\n"		\
+	"	mov %1,  0\n"			\
+	"	mov %R1, 0\n"			\
 	"	j   2b\n"			\
 	"	.previous\n"			\
 	"	.section __ex_table, \"a\"\n"	\

arch/arc/kernel/setup.c

@@ -332,10 +332,6 @@ static void arc_chk_core_config(void)
 		pr_warn("CONFIG_ARC_FPU_SAVE_RESTORE needed for working apps\n");
 	else if (!cpu->extn.fpu_dp && fpu_enabled)
 		panic("FPU non-existent, disable CONFIG_ARC_FPU_SAVE_RESTORE\n");
-
-	if (is_isa_arcv2() && IS_ENABLED(CONFIG_SMP) && cpu->isa.atomic &&
-	    !IS_ENABLED(CONFIG_ARC_STAR_9000923308))
-		panic("llock/scond livelock workaround missing\n");
 }
 
 /*

arch/arc/kernel/stacktrace.c

@@ -142,7 +142,7 @@ arc_unwind_core(struct task_struct *tsk, struct pt_regs *regs,
 	 * prelogue is setup (callee regs saved and then fp set and not other
 	 * way around
 	 */
-	pr_warn("CONFIG_ARC_DW2_UNWIND needs to be enabled\n");
+	pr_warn_once("CONFIG_ARC_DW2_UNWIND needs to be enabled\n");
 	return 0;
 
 #endif

arch/arc/mm/cache.c

@@ -914,6 +914,15 @@ void arc_cache_init(void)
 
 	printk(arc_cache_mumbojumbo(0, str, sizeof(str)));
 
+	/*
+	 * Only master CPU needs to execute rest of function:
+	 *  - Assume SMP so all cores will have same cache config so
+	 *    any geomtry checks will be same for all
+	 *  - IOC setup / dma callbacks only need to be setup once
+	 */
+	if (cpu)
+		return;
+
 	if (IS_ENABLED(CONFIG_ARC_HAS_ICACHE)) {
 		struct cpuinfo_arc_cache *ic = &cpuinfo_arc700[cpu].icache;
 

arch/arm/boot/compressed/head.S

@@ -776,7 +776,7 @@ __armv7_mmu_cache_on:
 		orrne	r0, r0, #1		@ MMU enabled
 		movne	r1, #0xfffffffd		@ domain 0 = client
 		bic     r6, r6, #1 << 31        @ 32-bit translation system
-		bic     r6, r6, #3 << 0         @ use only ttbr0
+		bic     r6, r6, #(7 << 0) | (1 << 4)	@ use only ttbr0
 		mcrne	p15, 0, r3, c2, c0, 0	@ load page table pointer
 		mcrne	p15, 0, r1, c3, c0, 0	@ load domain access control
 		mcrne   p15, 0, r6, c2, c0, 2   @ load ttb control

arch/arm/boot/dts/Makefile

@@ -6,6 +6,7 @@ dtb-$(CONFIG_ARCH_BCM2708) += bcm2708-rpi-cm.dtb
 dtb-$(CONFIG_ARCH_BCM2835) += bcm2835-rpi-cm.dtb
 dtb-$(CONFIG_ARCH_BCM2709) += bcm2709-rpi-2-b.dtb
 dtb-$(CONFIG_ARCH_BCM2709) += bcm2710-rpi-3-b.dtb
+dtb-$(CONFIG_ARCH_BCM2709) += bcm2710-rpi-cm3.dtb
 
 # Raspberry Pi
 ifeq ($(CONFIG_ARCH_BCM2708),y)

arch/arm/boot/dts/armada-385-linksys.dtsi

@@ -58,8 +58,8 @@
 	soc {
 		ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
 			  MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000
-			  MBUS_ID(0x09, 0x09) 0 0xf1100000 0x10000
-			  MBUS_ID(0x09, 0x05) 0 0xf1110000 0x10000>;
+			  MBUS_ID(0x09, 0x19) 0 0xf1100000 0x10000
+			  MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000>;
 
 		internal-regs {
 
@@ -245,7 +245,7 @@
 		button@2 {
 			label = "Factory Reset Button";
 			linux,code = <KEY_RESTART>;
-			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+			gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
 		};
 	};
 
@@ -260,7 +260,7 @@
 		};
 
 		sata {
-			gpios = <&gpio1 22 GPIO_ACTIVE_HIGH>;
+			gpios = <&gpio1 22 GPIO_ACTIVE_LOW>;
 			default-state = "off";
 		};
 	};
@@ -313,7 +313,7 @@
 
 &pinctrl {
 	keys_pin: keys-pin {
-		marvell,pins = "mpp24", "mpp47";
+		marvell,pins = "mpp24", "mpp29";
 		marvell,function = "gpio";
 	};
 

arch/arm/boot/dts/armada-390.dtsi

@@ -47,6 +47,8 @@
 #include "armada-39x.dtsi"
 
 / {
+	compatible = "marvell,armada390";
+
 	soc {
 		internal-regs {
 			pinctrl@18000 {
@@ -55,3 +57,4 @@
 			};
 		};
 	};
+};

arch/arm/boot/dts/armada-xp-linksys-mamba.dts

@@ -304,13 +304,13 @@
 		button@1 {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
-			gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>;
+			gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
 		};
 
 		button@2 {
 			label = "Factory Reset Button";
 			linux,code = <KEY_RESTART>;
-			gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>;
+			gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
 		};
 	};
 

arch/arm/boot/dts/at91sam9x5.dtsi

@@ -106,7 +106,7 @@
 
 			pmc: pmc@fffffc00 {
 				compatible = "atmel,at91sam9x5-pmc", "syscon";
-				reg = <0xfffffc00 0x100>;
+				reg = <0xfffffc00 0x200>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
 				interrupt-controller;
 				#address-cells = <1>;

arch/arm/boot/dts/bcm2708-rpi-b-plus.dts

@@ -37,6 +37,11 @@
 		brcm,pins = <18 19 20 21>;
 		brcm,function = <4>; /* alt0 */
 	};
+
+	audio_pins: audio_pins {
+		brcm,pins = <40 45>;
+		brcm,function = <4>;
+	};
 };
 
 &sdhost {
@@ -116,6 +121,15 @@
 	};
 };
 
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+};
+
+&audio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&audio_pins>;
+};
+
 / {
 	__overrides__ {
 		uart0 = <&uart0>,"status";

arch/arm/boot/dts/bcm2708-rpi-b.dts

@@ -37,6 +37,11 @@
 		brcm,pins = <28 29 30 31>;
 		brcm,function = <6>; /* alt2 */
 	};
+
+	audio_pins: audio_pins {
+		brcm,pins = <40 45>;
+		brcm,function = <4>;
+	};
 };
 
 &sdhost {
@@ -110,6 +115,15 @@
 	};
 };
 
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
+};
+
+&audio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&audio_pins>;
+};
+
 / {
 	__overrides__ {
 		uart0 = <&uart0>,"status";

arch/arm/boot/dts/bcm2708-rpi-cm.dts

@@ -35,6 +35,11 @@
 		brcm,pins = <18 19 20 21>;
 		brcm,function = <4>; /* alt0 */
 	};
+
+	audio_pins: audio_pins {
+		brcm,pins;
+		brcm,function;
+	};
 };
 
 &spi0 {

arch/arm/boot/dts/bcm2708-rpi-cm.dtsi

@@ -23,9 +23,9 @@
 };
 
 
-&mmc {
+&sdhost {
 	pinctrl-names = "default";
-	pinctrl-0 = <&mmc_pins>;
+	pinctrl-0 = <&sdhost_pins>;
 	non-removable;
 	bus-width = <4>;
 	status = "okay";

arch/arm/boot/dts/bcm2708_common.dtsi

@@ -1,4 +1,8 @@
+#include "dt-bindings/clock/bcm2835.h"
 #include <dt-bindings/clock/bcm2835-aux.h>
+#include "dt-bindings/power/raspberrypi-power.h"
+#include "dt-bindings/gpio/gpio.h"
+#include "dt-bindings/pinctrl/bcm2835.h"
 #include "skeleton.dtsi"
 
 / {
@@ -53,10 +57,32 @@
 				     <1 24>,
 				     <1 25>,
 				     <1 26>,
-				     <1 27>;
+				     /* dma channel 11-14 share one irq */
+				     <1 27>,
+				     <1 27>,
+				     <1 27>,
+				     <1 27>,
+				     /* unused shared irq for all channels */
+				     <1 28>;
+			interrupt-names = "dma0",
+					  "dma1",
+					  "dma2",
+					  "dma3",
+					  "dma4",
+					  "dma5",
+					  "dma6",
+					  "dma7",
+					  "dma8",
+					  "dma9",
+					  "dma10",
+					  "dma11",
+					  "dma12",
+					  "dma13",
+					  "dma14",
+					  "dma-shared-all";
 
 			#dma-cells = <1>;
-			brcm,dma-channel-mask = <0x0f35>;
+			brcm,dma-channel-mask = <0x7f34>;
 		};
 
 		intc: interrupt-controller@7e00b200 {
@@ -85,9 +111,10 @@
 			reg = <0x7e101000 0x2000>;
 
 			/* CPRMAN derives everything from the platform's
-			 * oscillator.
+			 * oscillator except for a few clocks that may
+			 * derive from something else derived from CPRMAN..
 			 */
-			clocks = <&clk_osc>;
+			clocks = <&clk_osc>, <&dsi1 0>, <&dsi1 1>, <&dsi1 2>;
 			status = "disabled";
 		};
 
@@ -134,6 +161,7 @@
 
 		i2s: i2s@7e203000 {
 			compatible = "brcm,bcm2835-i2s";
+			#sound-dai-cells = <0>;
 			reg = <0x7e203000 0x24>,
 			      <0x7e101098 0x08>;
 
@@ -157,7 +185,7 @@
 			 * add more gpios if necessary as <&gpio 6 1>
 			 * (but do not forget to make them output!)
 			 */
-			cs-gpios = <0>, <0>;
+			cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
 		};
 
 		i2c0: i2c@7e205000 {
@@ -170,6 +198,29 @@
 			status = "disabled";
 		};
 
+		pixelvalve0: pixelvalve@7e206000 {
+			compatible = "brcm,bcm2835-pixelvalve0";
+			reg = <0x7e206000 0x100>;
+			status = "disabled";
+		};
+
+		dpi: dpi@7e208000 {
+			compatible = "brcm,bcm2835-dpi";
+			reg = <0x7e208000 0x8c>;
+			clocks = <&cprman BCM2835_CLOCK_VPU>,
+				 <&cprman BCM2835_CLOCK_DPI>;
+			clock-names = "core", "pixel";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		pixelvalve1: pixelvalve@7e207000 {
+			compatible = "brcm,bcm2835-pixelvalve1";
+			reg = <0x7e207000 0x100>;
+			status = "disabled";
+		};
+
 		pwm: pwm@7e20c000 {
 			compatible = "brcm,bcm2835-pwm";
 			reg = <0x7e20c000 0x28>;
@@ -227,6 +278,50 @@
 			status = "disabled";
 		};
 
+		hvs: hvs@7e400000 {
+			compatible = "brcm,bcm2835-hvs";
+			reg = <0x7e400000 0x6000>;
+			status = "disabled";
+		};
+
+		firmwarekms: firmwarekms@7e600000 {
+			compatible = "raspberrypi,rpi-firmware-kms";
+			/* SMI interrupt reg */
+			reg = <0x7e600000 0x100>;
+			interrupts = <2 16>;
+			brcm,firmware = <&firmware>;
+			status = "disabled";
+		};
+
+		smi: smi@7e600000 {
+			compatible = "brcm,bcm2835-smi";
+			reg = <0x7e600000 0x44>, <0x7e1010b0 0x8>;
+			interrupts = <2 16>;
+			brcm,smi-clock-source = <6>;
+			brcm,smi-clock-divisor = <4>;
+			dmas = <&dma 4>;
+			dma-names = "rx-tx";
+			status = "disabled";
+		};
+
+		dsi1: dsi@7e700000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#clock-cells = <1>;
+
+			compatible = "brcm,bcm2835-dsi1";
+			reg = <0x7e700000 0x8c>;
+			interrupts = <2 12>;
+
+			clocks = <&cprman BCM2835_PLLD_DSI1>,
+				 <&cprman BCM2835_CLOCK_DSI1E>,
+				 <&cprman BCM2835_CLOCK_DSI1P>;
+			clock-names = "phy", "escape", "pixel";
+			clock-output-names = "dsi1_byte", "dsi1_ddr2", "dsi1_ddr";
+			status = "disabled";
+			power-domains = <&power RPI_POWER_DOMAIN_DSI1>;
+		};
+
 		i2c1: i2c@7e804000 {
 			compatible = "brcm,bcm2708-i2c";
 			reg = <0x7e804000 0x1000>;
@@ -250,14 +345,21 @@
 			status = "disabled";
 		};
 
-		smi: smi@7e600000 {
-			compatible = "brcm,bcm2835-smi";
-			reg = <0x7e600000 0x44>, <0x7e1010b0 0x8>;
-			interrupts = <2 16>;
-			brcm,smi-clock-source = <6>;
-			brcm,smi-clock-divisor = <4>;
-			dmas = <&dma 4>;
-			dma-names = "rx-tx";
+		pixelvalve2: pixelvalve@7e807000 {
+			compatible = "brcm,bcm2835-pixelvalve2";
+			reg = <0x7e807000 0x100>;
+			status = "disabled";
+		};
+
+		hdmi: hdmi@7e902000 {
+			compatible = "brcm,bcm2835-hdmi";
+			reg = <0x7e902000 0x600>,
+			      <0x7e808000 0x100>;
+			ddc = <&i2c2>;
+			clocks = <&cprman BCM2835_PLLH_PIX>,
+				 <&cprman BCM2835_CLOCK_HSM>;
+			clock-names = "pixel", "hdmi";
+			power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
 			status = "disabled";
 		};
 
@@ -269,6 +371,13 @@
 				     <1 9>;
 		};
 
+		v3d: v3d@7ec00000 {
+			compatible = "brcm,vc4-v3d";
+			reg = <0x7ec00000 0x1000>;
+			power-domains = <&power RPI_POWER_DOMAIN_V3D>;
+			status = "disabled";
+		};
+
 		firmware: firmware {
 			compatible = "raspberrypi,bcm2835-firmware";
 			mboxes = <&mailbox>;
@@ -303,6 +412,11 @@
 			firmware = <&firmware>;
 		};
 
+		gpu: gpu {
+			compatible = "brcm,bcm2835-vc4";
+			status = "disabled";
+		};
+
 		/* Onboard audio */
 		audio: audio {
 			compatible = "brcm,bcm2835-audio";

arch/arm/boot/dts/bcm2709-rpi-2-b.dts

@@ -37,6 +37,11 @@
 		brcm,pins = <18 19 20 21>;
 		brcm,function = <4>; /* alt0 */
 	};
+
+	audio_pins: audio_pins {
+		brcm,pins = <40 45>;
+		brcm,function = <4>;
+	};
 };
 
 &sdhost {
@@ -116,6 +121,15 @@
 	};
 };
 
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+};
+
+&audio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&audio_pins>;
+};
+
 / {
 	__overrides__ {
 		uart0 = <&uart0>,"status";

arch/arm/boot/dts/bcm2710-rpi-3-b.dts

@@ -61,6 +61,11 @@
 		brcm,function;
 		brcm,pull;
 	};
+
+	audio_pins: audio_pins {
+		brcm,pins = <40 41>;
+		brcm,function = <4>;
+	};
 };
 
 &sdhost {
@@ -161,6 +166,11 @@
 	};
 };
 
+&audio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&audio_pins>;
+};
+
 / {
 	chosen {
 		bootargs = "8250.nr_uarts=1";

arch/arm/boot/dts/bcm2710-rpi-cm3.dts

@@ -0,0 +1,163 @@
+/dts-v1/;
+
+#include "bcm2710.dtsi"
+
+/ {
+	compatible = "brcm,bcm2710","brcm,bcm2709";
+	model = "Raspberry Pi Compute Module 3";
+};
+
+&gpio {
+	sdhost_pins: sdhost_pins {
+		brcm,pins = <48 49 50 51 52 53>;
+		brcm,function = <4>; /* alt0 */
+		brcm,pull = <0 2 2 2 2 2>;
+	};
+
+	spi0_pins: spi0_pins {
+		brcm,pins = <9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_cs_pins: spi0_cs_pins {
+		brcm,pins = <8 7>;
+		brcm,function = <1>; /* output */
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+
+	i2s_pins: i2s {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	audio_pins: audio_pins {
+		brcm,pins;
+		brcm,function;
+	};
+};
+
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_pins>;
+	non-removable;
+	bus-width = <4>;
+	status = "okay";
+	brcm,overclock-50 = <0>;
+};
+
+&soc {
+	virtgpio: virtgpio {
+		compatible = "brcm,bcm2835-virtgpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+		firmware = <&firmware>;
+		status = "okay";
+	};
+};
+
+&fb {
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
+	cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
+
+	spidev0: spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <500000>;
+	};
+
+	spidev1: spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <500000>;
+	};
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	#sound-dai-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+&random {
+	status = "okay";
+};
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "mmc0";
+		gpios = <&virtgpio 0 0>;
+	};
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+};
+
+&audio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&audio_pins>;
+};
+
+/ {
+	__overrides__ {
+		uart0 = <&uart0>,"status";
+		uart0_clkrate = <&clk_uart0>,"clock-frequency:0";
+		uart1 = <&uart1>,"status";
+		i2s = <&i2s>,"status";
+		spi = <&spi0>,"status";
+		i2c0 = <&i2c0>,"status";
+		i2c1 = <&i2c1>,"status";
+		i2c2_iknowwhatimdoing = <&i2c2>,"status";
+		i2c0_baudrate = <&i2c0>,"clock-frequency:0";
+		i2c1_baudrate = <&i2c1>,"clock-frequency:0";
+		i2c2_baudrate = <&i2c2>,"clock-frequency:0";
+		core_freq = <&clk_core>,"clock-frequency:0";
+
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+
+		audio = <&audio>,"status";
+		watchdog = <&watchdog>,"status";
+		random = <&random>,"status";
+		sd_overclock = <&sdhost>,"brcm,overclock-50:0";
+		sd_force_pio = <&sdhost>,"brcm,force-pio?";
+		sd_pio_limit = <&sdhost>,"brcm,pio-limit:0";
+		sd_debug     = <&sdhost>,"brcm,debug";
+	};
+};

arch/arm/boot/dts/exynos4210-trats.dts

@@ -298,6 +298,8 @@
 		compatible = "maxim,max8997-pmic";
 
 		reg = <0x66>;
+		interrupt-parent = <&gpx0>;
+		interrupts = <7 0>;
 
 		max8997,pmic-buck1-uses-gpio-dvs;
 		max8997,pmic-buck2-uses-gpio-dvs;

arch/arm/boot/dts/imx6qdl.dtsi

@@ -221,7 +221,7 @@
 					clocks = <&clks IMX6QDL_CLK_SPDIF_GCLK>, <&clks IMX6QDL_CLK_OSC>,
 						 <&clks IMX6QDL_CLK_SPDIF>, <&clks IMX6QDL_CLK_ASRC>,
 						 <&clks IMX6QDL_CLK_DUMMY>, <&clks IMX6QDL_CLK_ESAI_EXTAL>,
-						 <&clks IMX6QDL_CLK_IPG>, <&clks IMX6QDL_CLK_MLB>,
+						 <&clks IMX6QDL_CLK_IPG>, <&clks IMX6QDL_CLK_DUMMY>,
 						 <&clks IMX6QDL_CLK_DUMMY>, <&clks IMX6QDL_CLK_SPBA>;
 					clock-names = "core",  "rxtx0",
 						      "rxtx1", "rxtx2",

arch/arm/boot/dts/kirkwood-ib62x0.dts

@@ -113,7 +113,7 @@
 
 	partition@e0000 {
 		label = "u-boot environment";
-		reg = <0xe0000 0x100000>;
+		reg = <0xe0000 0x20000>;
 	};
 
 	partition@100000 {

arch/arm/boot/dts/omap3-overo-base.dtsi

@@ -223,7 +223,9 @@
 };
 
 &gpmc {
-	ranges = <0 0 0x00000000 0x20000000>;
+	ranges = <0 0 0x30000000 0x1000000>,	/* CS0 */
+		 <4 0 0x2b000000 0x1000000>,	/* CS4 */
+		 <5 0 0x2c000000 0x1000000>;	/* CS5 */
 
 	nand@0,0 {
 		linux,mtd-name= "micron,mt29c4g96maz";

arch/arm/boot/dts/omap3-overo-chestnut43-common.dtsi

@@ -55,8 +55,6 @@
 #include "omap-gpmc-smsc9221.dtsi"
 
 &gpmc {
-	ranges = <5 0 0x2c000000 0x1000000>;	/* CS5 */
-
 	ethernet@gpmc {
 		reg = <5 0 0xff>;
 		interrupt-parent = <&gpio6>;

arch/arm/boot/dts/omap3-overo-tobi-common.dtsi

@@ -27,8 +27,6 @@
 #include "omap-gpmc-smsc9221.dtsi"
 
 &gpmc {
-	ranges = <5 0 0x2c000000 0x1000000>;	/* CS5 */
-
 	ethernet@gpmc {
 		reg = <5 0 0xff>;
 		interrupt-parent = <&gpio6>;

arch/arm/boot/dts/omap3-overo-tobiduo-common.dtsi

@@ -15,9 +15,6 @@
 #include "omap-gpmc-smsc9221.dtsi"
 
 &gpmc {
-	ranges = <4 0 0x2b000000 0x1000000>,	/* CS4 */
-		 <5 0 0x2c000000 0x1000000>;	/* CS5 */
-
 	smsc1: ethernet@gpmc {
 		reg = <5 0 0xff>;
 		interrupt-parent = <&gpio6>;

arch/arm/boot/dts/overlays/Makefile

@@ -12,16 +12,21 @@ ifeq ($(CONFIG_ARCH_BCM2835),y)
    RPI_DT_OVERLAYS=y
 endif
 
+dtbo-$(RPI_DT_OVERLAYS) += adau1977-adc.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += ads1015.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += ads7846.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += akkordion-iqdacplus.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += allo-piano-dac-pcm512x-audio.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += at86rf233.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += audioinjector-wm8731-audio.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += audremap.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += bmp085_i2c-sensor.dtbo
-dtbo-$(RPI_DT_OVERLAYS) += boomberry-dac.dtbo
-dtbo-$(RPI_DT_OVERLAYS) += boomberry-digi.dtbo
-dtbo-$(RPI_DT_OVERLAYS) += dpi24.dtbo
-dtbo-$(RPI_DT_OVERLAYS) += dwc2.dtbo
-dtbo-$(RPI_DT_OVERLAYS) += dwc-otg.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += dht11.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += dionaudio-loco.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += dpi18.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += dpi24.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += dwc-otg.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += dwc2.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += enc28j60.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += gpio-ir.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += gpio-poweroff.dtbo
@@ -29,19 +34,25 @@ dtbo-$(RPI_DT_OVERLAYS) += hifiberry-amp.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += hifiberry-dac.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += hifiberry-dacplus.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += hifiberry-digi.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += hifiberry-digi-pro.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += hy28a.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += hy28b.dtbo
-dtbo-$(RPI_DT_OVERLAYS) += i2c-rtc.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += i2c-gpio.dtbo
-dtbo-$(RPI_DT_OVERLAYS) += i2c-mux-pca9548a.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += i2c-mux.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += i2c-pwm-pca9685a.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += i2c-rtc.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += i2c0-bcm2708.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += i2c1-bcm2708.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += i2s-gpio28-31.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += i2s-mmap.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += iqaudio-dac.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += iqaudio-dacplus.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += iqaudio-digi-wm8804-audio.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += justboom-dac.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += justboom-digi.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += lirc-rpi.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += mcp23017.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += mcp23s17.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += mcp2515-can0.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += mcp2515-can1.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += mmc.dtbo
@@ -54,6 +65,7 @@ dtbo-$(RPI_DT_OVERLAYS) += piscreen2r.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += pitft22.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += pitft28-capacitive.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += pitft28-resistive.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += pitft35-resistive.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += pps-gpio.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += pwm.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += pwm-2chan.dtbo
@@ -65,22 +77,28 @@ dtbo-$(RPI_DT_OVERLAYS) += rpi-display.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += rpi-ft5406.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += rpi-proto.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += rpi-sense.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += rra-digidac1-wm8741-audio.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += sc16is750-i2c.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += sc16is752-spi1.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += sdhost.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += sdio.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += sdio-1bit.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += sdtweak.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += smi.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += smi-dev.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += smi-nand.dtbo
-dtbo-$(RPI_DT_OVERLAYS) += smi.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += spi-gpio35-39.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += spi-rtc.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += spi0-hw-cs.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += spi1-1cs.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += spi1-2cs.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += spi1-3cs.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += spi2-1cs.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += spi2-2cs.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += spi2-3cs.dtbo
-dtbo-$(RPI_DT_OVERLAYS) += spi-gpio35-39.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += tinylcd35.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += uart1.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += vc4-fkms-v3d.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += vc4-kms-v3d.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += vga666.dtbo
 dtbo-$(RPI_DT_OVERLAYS) += w1-gpio.dtbo

arch/arm/boot/dts/overlays/README

@@ -161,6 +161,35 @@ Params:
         and the other i2c baudrate parameters.
 
 
+Name:   adau1977-adc
+Info:   Overlay for activation of ADAU1977 ADC codec over I2C for control
+        and I2S for data.
+Load:   dtoverlay=adau1977-adc
+Params: <None>
+
+
+Name:   ads1015
+Info:   Overlay for activation of Texas Instruments ADS1015 ADC over I2C
+Load:   dtoverlay=ads1015,<param>=<val>
+Params: addr                    I2C bus address of device. Set based on how the
+                                addr pin is wired. (default=0x48 assumes addr
+                                is pulled to GND)
+        cha_enable              Enable virtual channel a. (default=true)
+        cha_cfg                 Set the configuration for virtual channel a.
+                                (default=4 configures this channel for the
+                                voltage at A0 with respect to GND)
+        cha_datarate            Set the datarate (samples/sec) for this channel.
+                                (default=4 sets 1600 sps)
+        cha_gain                Set the gain of the Programmable Gain
+                                Amplifier for this channel. (default=2 sets the
+                                full scale of the channel to 2.048 Volts)
+
+        Channel (ch) parameters can be set for each enabled channel.
+        A maximum of 4 channels can be enabled (letters a thru d).
+        For more information refer to the device datasheet at:
+        http://www.ti.com/lit/ds/symlink/ads1015.pdf
+
+
 Name:   ads7846
 Info:   ADS7846 Touch controller
 Load:   dtoverlay=ads7846,<param>=<val>
@@ -206,6 +235,26 @@ Params: 24db_digital_gain       Allow gain to be applied via the PCM512x codec
                                 that does not result in clipping/distortion!)
 
 
+Name:   allo-piano-dac-pcm512x-audio
+Info:   Configures the Allo Piano DAC (2.0/2.1) audio cards.
+        (NB. This initial support is for 2.0 channel audio ONLY! ie. stereo.
+        The subwoofer outputs on the Piano 2.1 are not currently supported!)
+Load:   dtoverlay=allo-piano-dac-pcm512x-audio,<param>
+Params: 24db_digital_gain       Allow gain to be applied via the PCM512x codec
+                                Digital volume control.
+                                (The default behaviour is that the Digital
+                                volume control is limited to a maximum of
+                                0dB. ie. it can attenuate but not provide
+                                gain. For most users, this will be desired
+                                as it will prevent clipping. By appending
+                                the 24db_digital_gain parameter, the Digital
+                                volume control will allow up to 24dB of
+                                gain. If this parameter is enabled, it is the
+                                responsibility of the user to ensure that
+                                the Digital volume control is set to a value
+                                that does not result in clipping/distortion!)
+
+
 Name:   at86rf233
 Info:   Configures the Atmel AT86RF233 802.15.4 low-power WPAN transceiver,
         connected to spi0.0
@@ -218,6 +267,21 @@ Params: interrupt               GPIO used for INT (default 23)
                                 arrays (0=+0pF, 15=+4.5pF, default 15)
 
 
+Name:   audioinjector-wm8731-audio
+Info:   Configures the audioinjector.net audio add on soundcard
+Load:   dtoverlay=audioinjector-wm8731-audio
+Params: <None>
+
+
+Name:   audremap
+Info:   Switches PWM sound output to pins 12 (Right) & 13 (Left)
+Load:   dtoverlay=audremap,<param>=<val>
+Params: swap_lr                 Reverse the channel allocation, which will also
+                                swap the audio jack outputs (default off)
+        enable_jack             Don't switch off the audio jack output
+                                (default off)
+
+
 Name:   bmp085_i2c-sensor
 Info:   Configures the BMP085/BMP180 digital barometric pressure and temperature
         sensors from Bosch Sensortec
@@ -225,32 +289,6 @@ Load:   dtoverlay=bmp085_i2c-sensor
 Params: <None>
 
 
-Name:   boomberry-dac
-Info:   Configures the BoomBerry DAC HAT, Amp HAT, DAC Zero and Amp Zero audio
-        cards
-Load:   dtoverlay=boomberry-dac,<param>=<val>
-Params: 24db_digital_gain       Allow gain to be applied via the PCM512x codec
-                                Digital volume control. Enable with
-                                "dtoverlay=boomberry-dac,24db_digital_gain"
-                                (The default behaviour is that the Digital
-                                volume control is limited to a maximum of
-                                0dB. ie. it can attenuate but not provide
-                                gain. For most users, this will be desired
-                                as it will prevent clipping. By appending
-                                the 24dB_digital_gain parameter, the Digital
-                                volume control will allow up to 24dB of
-                                gain. If this parameter is enabled, it is the
-                                responsibility of the user to ensure that
-                                the Digital volume control is set to a value
-                                that does not result in clipping/distortion!)
-
-
-Name:   boomberry-digi
-Info:   Configures the BoomBerry Digi HAT and Digi Zero audio cards
-Load:   dtoverlay=boomberry-digi
-Params: <None>
-
-
 Name:   dht11
 Info:   Overlay for the DHT11/DHT21/DHT22 humidity/temperature sensors
         Also sometimes found with the part number(s) AM230x.
@@ -259,6 +297,20 @@ Params: gpiopin                 GPIO connected to the sensor's DATA output.
                                 (default 4)
 
 
+Name:   dionaudio-loco
+Info:   Configures the Dion Audio LOCO DAC-AMP
+Load:   dtoverlay=dionaudio-loco
+Params: <None>
+
+
+Name:   dpi18
+Info:   Overlay for a generic 18-bit DPI display
+        This uses GPIOs 0-21 (so no I2C, uart etc.), and activates the output
+        2-3 seconds after the kernel has started.
+Load:   dtoverlay=dpi18
+Params: <None>
+
+
 Name:   dpi24
 Info:   Overlay for a generic 24-bit DPI display
         This uses GPIOs 0-27 (so no I2C, uart etc.), and activates the output
@@ -316,7 +368,7 @@ Params: gpio_pin                Input pin number. Default is 18.
 
 
 Name:   gpio-poweroff
-Info:   Drives a GPIO high or low on reboot
+Info:   Drives a GPIO high or low on poweroff (including halt)
 Load:   dtoverlay=gpio-poweroff,<param>=<val>
 Params: gpiopin                 GPIO for signalling (default 26)
 
@@ -357,14 +409,22 @@ Params: 24db_digital_gain       Allow gain to be applied via the PCM512x codec
                                 responsibility of the user to ensure that
                                 the Digital volume control is set to a value
                                 that does not result in clipping/distortion!)
+        slave                   Force DAC+ Pro into slave mode, using Pi as
+                                master for bit clock and frame clock.
 
 
 Name:   hifiberry-digi
-Info:   Configures the HifiBerry Digi audio card
+Info:   Configures the HifiBerry Digi and Digi+ audio card
 Load:   dtoverlay=hifiberry-digi
 Params: <None>
 
 
+Name:   hifiberry-digi-pro
+Info:   Configures the HifiBerry Digi+ Pro audio card
+Load:   dtoverlay=hifiberry-digi-pro
+Params: <None>
+
+
 Name:   hy28a
 Info:   HY28A - 2.8" TFT LCD Display Module by HAOYU Electronics
         Default values match Texy's display shield
@@ -414,10 +474,19 @@ Params: i2c_gpio_sda            GPIO used for I2C data (default "23")
                                 (default "2" = ~100kHz)
 
 
-Name:   i2c-mux-pca9548a
-Info:   Adds support for an NXP PCA9548A I2C multiplexer on i2c_arm
-Load:   dtoverlay=i2c-mux-pca9548a,<param>=<val>
-Params: addr                    I2C address of PCA9548A (default 0x70)
+Name:   i2c-mux
+Info:   Adds support for a number of I2C bus multiplexers on i2c_arm
+Load:   dtoverlay=i2c-mux,<param>=<val>
+Params: pca9542                 Select the NXP PCA9542 device
+
+        pca9545                 Select the NXP PCA9545 device
+
+        pca9548                 Select the NXP PCA9548 device
+
+        addr                    Change I2C address of the device (default 0x70)
+
+
+[ The i2c-mux-pca9548a overlay has been deleted. See i2c-mux. ]
 
 
 Name:   i2c-pwm-pca9685a
@@ -447,6 +516,9 @@ Params: ds1307                  Select the DS1307 device
 
         trickle-resistor-ohms   Resistor value for trickle charge (DS1339-only)
 
+        wakeup-source           Specify that the RTC can be used as a wakeup
+                                source
+
 
 Name:   i2c0-bcm2708
 Info:   Enable the i2c_bcm2708 driver for the i2c0 bus. Not all pin combinations
@@ -483,8 +555,21 @@ Params: <None>
 
 Name:   iqaudio-dac
 Info:   Configures the IQaudio DAC audio card
-Load:   dtoverlay=iqaudio-dac
-Params: <None>
+Load:   dtoverlay=iqaudio-dac,<param>
+Params: 24db_digital_gain       Allow gain to be applied via the PCM512x codec
+                                Digital volume control. Enable with
+                                "dtoverlay=iqaudio-dac,24db_digital_gain"
+                                (The default behaviour is that the Digital
+                                volume control is limited to a maximum of
+                                0dB. ie. it can attenuate but not provide
+                                gain. For most users, this will be desired
+                                as it will prevent clipping. By appending
+                                the 24db_digital_gain parameter, the Digital
+                                volume control will allow up to 24dB of
+                                gain. If this parameter is enabled, it is the
+                                responsibility of the user to ensure that
+                                the Digital volume control is set to a value
+                                that does not result in clipping/distortion!)
 
 
 Name:   iqaudio-dacplus
@@ -504,6 +589,45 @@ Params: 24db_digital_gain       Allow gain to be applied via the PCM512x codec
                                 responsibility of the user to ensure that
                                 the Digital volume control is set to a value
                                 that does not result in clipping/distortion!)
+        auto_mute_amp           If specified, unmute/mute the IQaudIO amp when
+                                starting/stopping audio playback.
+        unmute_amp              If specified, unmute the IQaudIO amp once when
+                                the DAC driver module loads.
+
+
+Name:   iqaudio-digi-wm8804-audio
+Info:   Configures the IQAudIO Digi WM8804 audio card
+Load:   dtoverlay=iqaudio-digi-wm8804-audio,<param>=<val>
+Params: card_name               Override the default, "IQAudIODigi", card name.
+        dai_name                Override the default, "IQAudIO Digi", dai name.
+        dai_stream_name         Override the default, "IQAudIO Digi HiFi",
+                                dai stream name.
+
+
+Name:   justboom-dac
+Info:   Configures the JustBoom DAC HAT, Amp HAT, DAC Zero and Amp Zero audio
+        cards
+Load:   dtoverlay=justboom-dac,<param>=<val>
+Params: 24db_digital_gain       Allow gain to be applied via the PCM512x codec
+                                Digital volume control. Enable with
+                                "dtoverlay=justboom-dac,24db_digital_gain"
+                                (The default behaviour is that the Digital
+                                volume control is limited to a maximum of
+                                0dB. ie. it can attenuate but not provide
+                                gain. For most users, this will be desired
+                                as it will prevent clipping. By appending
+                                the 24dB_digital_gain parameter, the Digital
+                                volume control will allow up to 24dB of
+                                gain. If this parameter is enabled, it is the
+                                responsibility of the user to ensure that
+                                the Digital volume control is set to a value
+                                that does not result in clipping/distortion!)
+
+
+Name:   justboom-digi
+Info:   Configures the JustBoom Digi HAT and Digi Zero audio cards
+Load:   dtoverlay=justboom-digi
+Params: <None>
 
 
 Name:   lirc-rpi
@@ -532,6 +656,39 @@ Params: gpio_out_pin            GPIO for output (default "17")
                                 (default "off")
 
 
+Name:   mcp23017
+Info:   Configures the MCP23017 I2C GPIO expander
+Load:   dtoverlay=mcp23017,<param>=<val>
+Params: gpiopin                 Gpio pin connected to the INTA output of the
+                                MCP23017 (default: 4)
+
+        addr                    I2C address of the MCP23017 (default: 0x20)
+
+
+Name:   mcp23s17
+Info:   Configures the MCP23S08/17 SPI GPIO expanders.
+        If devices are present on SPI1 or SPI2, those interfaces must be enabled
+        with one of the spi1-1/2/3cs and/or spi2-1/2/3cs overlays.
+        If interrupts are enabled for a device on a given CS# on a SPI bus, that
+        device must be the only one present on that SPI bus/CS#.
+Load:   dtoverlay=mcp23s17,<param>=<val>
+Params: s08-spi<n>-<m>-present  4-bit integer, bitmap indicating MCP23S08
+                                devices present on SPI<n>, CS#<m>
+
+        s17-spi<n>-<m>-present  8-bit integer, bitmap indicating MCP23S17
+                                devices present on SPI<n>, CS#<m>
+
+        s08-spi<n>-<m>-int-gpio integer, enables interrupts on a single
+                                MCP23S08 device on SPI<n>, CS#<m>, specifies
+                                the GPIO pin to which INT output of MCP23S08
+                                is connected.
+
+        s17-spi<n>-<m>-int-gpio integer, enables mirrored interrupts on a
+                                single MCP23S17 device on SPI<n>, CS#<m>,
+                                specifies the GPIO pin to which either INTA
+                                or INTB output of MCP23S17 is connected.
+
+
 Name:   mcp2515-can0
 Info:   Configures the MCP2515 CAN controller on spi0.0
 Load:   dtoverlay=mcp2515-can0,<param>=<val>
@@ -616,7 +773,9 @@ Info:   Switch Pi3 Bluetooth function to use the mini-UART (ttyS0) and restore
         N.B. It is also necessary to edit /lib/systemd/system/hciuart.service
         and replace ttyAMA0 with ttyS0, unless you have a system with udev rules
         that create /dev/serial0 and /dev/serial1, in which case use
-        /dev/serial1 instead because it will always be correct.
+        /dev/serial1 instead because it will always be correct. Furthermore,
+        you must also set core_freq=250 in config.txt or the miniuart will not
+        work.
 Load:   dtoverlay=pi3-miniuart-bt
 Params: <None>
 
@@ -695,10 +854,24 @@ Params: speed                   Display SPI bus speed
         debug                   Debug output level {0-7}
 
 
+Name:   pitft35-resistive
+Info:   Adafruit PiTFT 3.5" resistive touch screen
+Load:   dtoverlay=pitft35-resistive,<param>=<val>
+Params: speed                   Display SPI bus speed
+
+        rotate                  Display rotation {0,90,180,270}
+
+        fps                     Delay between frame updates
+
+        debug                   Debug output level {0-7}
+
+
 Name:   pps-gpio
 Info:   Configures the pps-gpio (pulse-per-second time signal via GPIO).
 Load:   dtoverlay=pps-gpio,<param>=<val>
 Params: gpiopin                 Input GPIO (default "18")
+        assert_falling_edge     When present, assert is indicated by a falling
+                                edge, rather than by a rising edge
 
 
 Name:   pwm
@@ -796,6 +969,32 @@ Load:   dtoverlay=rpi-sense
 Params: <None>
 
 
+Name:   rra-digidac1-wm8741-audio
+Info:   Configures the Red Rocks Audio DigiDAC1 soundcard
+Load:   dtoverlay=rra-digidac1-wm8741-audio
+Params: <None>
+
+
+Name:   sc16is750-i2c
+Info:   Overlay for the NXP SC16IS750 UART with I2C Interface
+        Enables the chip on I2C1 at 0x48. To select another address,
+        please refer to table 10 in reference manual.
+
+Load:   dtoverlay=sc16is750-i2c,<param>=<val>
+Params: int_pin                 GPIO used for IRQ (default 24)
+        addr                    Address (default 0x48)
+
+
+Name:   sc16is752-spi1
+Info:   Overlay for the NXP SC16IS752 Dual UART with SPI Interface
+        Enables the chip on SPI1.
+        N.B.: spi1 is only accessible on devices with a 40pin header, eg:
+              A+, B+, Zero and PI2 B; as well as the Compute Module.
+
+Load:   dtoverlay=sc16is752-spi1,<param>=<val>
+Params: int_pin                 GPIO used for IRQ (default 24)
+
+
 Name:   sdhost
 Info:   Selects the bcm2835-sdhost SD/MMC driver, optionally with overclock.
         N.B. This overlay is designed for situations where the mmc driver is
@@ -898,6 +1097,18 @@ Load:   dtoverlay=spi-gpio35-39
 Params: <None>
 
 
+Name:   spi-rtc
+Info:   Adds support for a number of SPI Real Time Clock devices
+Load:   dtoverlay=spi-rtc,<param>=<val>
+Params: pcf2123                 Select the PCF2123 device
+
+
+Name:   spi0-hw-cs
+Info:   Re-enables hardware CS/CE (chip selects) for SPI0
+Load:   dtoverlay=spi0-hw-cs
+Params: <None>
+
+
 Name:   spi1-1cs
 Info:   Enables spi1 with a single chip select (CS) line and associated spidev
         dev node. The gpio pin number for the CS line and spidev device node
@@ -1036,6 +1247,17 @@ Params: txd1_pin                GPIO pin for TXD1 (14, 32 or 40 - default 14)
         rxd1_pin                GPIO pin for RXD1 (15, 33 or 41 - default 15)
 
 
+Name:   vc4-fkms-v3d
+Info:   Enable Eric Anholt's DRM VC4 V3D driver on top of the dispmanx
+        display stack.
+Load:   dtoverlay=vc4-fkms-v3d,<param>
+Params: cma-256                 CMA is 256MB, 256MB-aligned (needs 1GB)
+        cma-192                 CMA is 192MB, 256MB-aligned (needs 1GB)
+        cma-128                 CMA is 128MB, 128MB-aligned
+        cma-96                  CMA is 96MB, 128MB-aligned
+        cma-64                  CMA is 64MB, 64MB-aligned
+
+
 Name:   vc4-kms-v3d
 Info:   Enable Eric Anholt's DRM VC4 HDMI/HVS/V3D driver. Running startx or
         booting to GUI while this overlay is in use will cause interesting

arch/arm/boot/dts/overlays/adau1977-adc-overlay.dts

@@ -0,0 +1,53 @@
+// Definitions for ADAU1977 ADC
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+    
+	fragment@0 {
+		target = <&soc>;
+		
+		__overlay__ {
+			codec_supply: fixedregulator@0 {
+				compatible = "regulator-fixed";
+				regulator-name = "AVDD";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+		};
+	};
+	
+	fragment@1 {
+        	target = <&i2c>;
+        	
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+			
+			adau1977: codec@11 {
+                        	compatible = "adi,adau1977";
+                        	reg = <0x11>;
+                        	reset-gpios = <&gpio 5 0>;
+                        	AVDD-supply = <&codec_supply>;
+                	};
+        	};
+	};
+
+	fragment@2 {
+		target = <&i2s>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@3 {
+		target = <&sound>;
+		__overlay__ {
+			compatible = "adi,adau1977-adc";
+			i2s-controller = <&i2s>;
+			status = "okay";
+		};
+	};
+};

arch/arm/boot/dts/overlays/ads1015-overlay.dts

@@ -0,0 +1,98 @@
+/*
+ * 2016 - Erik Sejr
+ */
+/dts-v1/;
+/plugin/;
+
+/ {
+    compatible = "brcm,bcm2708";
+    /* ----------- ADS1015 ------------ */
+    fragment@0 {
+        target = <&i2c_arm>;
+        __overlay__ {
+            #address-cells = <1>;
+            #size-cells = <0>;
+            status = "okay";
+            ads1015: ads1015 {
+                compatible = "ti,ads1015";
+                status = "okay";
+                #address-cells = <1>;
+                #size-cells = <0>;
+                reg = <0x48>;
+            };
+        };
+    };
+
+    fragment@1 {
+        target-path = "i2c_arm/ads1015";
+        __overlay__ {
+            #address-cells = <1>;
+            #size-cells = <0>;
+            channel_a: channel_a {
+                reg = <4>;
+                ti,gain = <2>;
+                ti,datarate = <4>;
+            };
+        };
+    };
+
+    fragment@2 {
+        target-path = "i2c_arm/ads1015";
+        __dormant__ {
+            #address-cells = <1>;
+            #size-cells = <0>;
+            channel_b: channel_b {
+                reg = <5>;
+                ti,gain = <2>;
+                ti,datarate = <4>;
+            };
+        };
+    };
+
+    fragment@3 {
+        target-path = "i2c_arm/ads1015";
+        __dormant__ {
+            #address-cells = <1>;
+            #size-cells = <0>;
+            channel_c: channel_c {
+                reg = <6>;
+                ti,gain = <2>;
+                ti,datarate = <4>;
+            };
+        };
+    };
+
+    fragment@4 {
+        target-path = "i2c_arm/ads1015";
+        __dormant__ {
+            #address-cells = <1>;
+            #size-cells = <0>;
+            channel_d: channel_d {
+                reg = <7>;
+                ti,gain = <2>;
+                ti,datarate = <4>;
+            };
+        };
+    };
+
+    __overrides__ {
+        addr =            <&ads1015>,"reg:0";
+        cha_enable =      <0>,"=1";
+        cha_cfg =         <&channel_a>,"reg:0";
+        cha_gain =        <&channel_a>,"ti,gain:0";
+        cha_datarate =    <&channel_a>,"ti,datarate:0";
+        chb_enable =      <0>,"=2";
+        chb_cfg =         <&channel_b>,"reg:0";
+        chb_gain =        <&channel_b>,"ti,gain:0";
+        chb_datarate =    <&channel_b>,"ti,datarate:0";
+        chc_enable =      <0>,"=3";
+        chc_cfg =         <&channel_c>,"reg:0";
+        chc_gain =        <&channel_c>,"ti,gain:0";
+        chc_datarate =    <&channel_c>,"ti,datarate:0";
+        chd_enable =      <0>,"=4";
+        chd_cfg =         <&channel_d>,"reg:0";
+        chd_gain =        <&channel_d>,"ti,gain:0";
+        chd_datarate =    <&channel_d>,"ti,datarate:0";
+   };
+
+};

arch/arm/boot/dts/overlays/allo-piano-dac-pcm512x-audio-overlay.dts

@@ -0,0 +1,54 @@
+/*
+ * Definitions for Allo Piano DAC (2.0/2.1) boards
+ *
+ * NB. The Piano DAC 2.1 board contains 2x TI PCM5142 DAC's. One DAC is stereo
+ * (left/right) and the other provides a subwoofer output, using DSP on the
+ * chip for digital high/low pass crossover.
+ * The initial support for this hardware, that doesn't require any codec driver
+ * modifications, uses only one DAC chip for stereo (left/right) output, the
+ * chip with 0x4c slave address. The other chip at 0x4d is currently ignored!
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&i2s>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&i2c1>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			pcm5142@4c {
+				#sound-dai-cells = <0>;
+				compatible = "ti,pcm5142";
+				reg = <0x4c>;
+				status = "okay";
+			};
+		};
+	};
+
+	fragment@2 {
+		target = <&sound>;
+		piano_dac: __overlay__ {
+			compatible = "allo,piano-dac";
+			i2s-controller = <&i2s>;
+			status = "okay";
+		};
+	};
+
+	__overrides__ {
+		24db_digital_gain =
+			<&piano_dac>,"allo,24db_digital_gain?";
+	};
+};

arch/arm/boot/dts/overlays/audioinjector-wm8731-audio-overlay.dts

@@ -0,0 +1,39 @@
+// Definitions for audioinjector.net audio add on soundcard
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&i2s>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&i2c1>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			wm8731@1a {
+				#sound-dai-cells = <0>;
+				compatible = "wlf,wm8731";
+				reg = <0x1a>;
+				status = "okay";
+			};
+		};
+	};
+
+	fragment@2 {
+		target = <&sound>;
+		__overlay__ {
+			compatible = "ai,audioinjector-pi-soundcard";
+			i2s-controller = <&i2s>;
+			status = "okay";
+		};
+	};
+};

arch/arm/boot/dts/overlays/audremap-overlay.dts

@@ -0,0 +1,19 @@
+/dts-v1/;
+/plugin/;
+
+/ {
+        compatible = "brcm,bcm2708";
+
+        fragment@0 {
+                target = <&audio_pins>;
+                frag0: __overlay__ {
+                        brcm,pins = < 12 13 >;
+                        brcm,function = < 4 >; /* alt0 alt0 */
+                };
+        };
+
+	__overrides__ {
+		swap_lr = <&frag0>, "swap_lr?";
+		enable_jack = <&frag0>, "enable_jack?";
+	};
+};

arch/arm/boot/dts/overlays/dionaudio-loco-overlay.dts

@@ -0,0 +1,39 @@
+// Definitions for Dion Audio LOCO DAC-AMP
+
+/*
+ * PCM5242 DAC (in hardware mode) and TPA3118 AMP.
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&i2s>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target-path = "/";
+		__overlay__ {
+			pcm5102a-codec {
+				#sound-dai-cells = <0>;
+				compatible = "ti,pcm5102a";
+				status = "okay";
+			};
+		};
+	};
+
+	fragment@2 {
+		target = <&sound>;
+		__overlay__ {
+			compatible = "dionaudio,loco-pcm5242-tpa3118";
+			i2s-controller = <&i2s>;
+			status = "okay";
+		};
+	};
+};

arch/arm/boot/dts/overlays/dpi18-overlay.dts

@@ -0,0 +1,31 @@
+/dts-v1/;
+/plugin/;
+
+/{
+	compatible = "brcm,bcm2708";
+
+	// There is no DPI driver module, but we need a platform device
+	// node (that doesn't already use pinctrl) to hang the pinctrl
+	// reference on - leds will do
+
+	fragment@0 {
+		target = <&leds>;
+		__overlay__ {
+			pinctrl-names = "default";
+			pinctrl-0 = <&dpi18_pins>;
+		};
+	};
+
+	fragment@1 {
+		target = <&gpio>;
+		__overlay__ {
+			dpi18_pins: dpi18_pins {
+				brcm,pins = <0 1 2 3 4 5 6 7 8 9 10 11
+					     12 13 14 15 16 17 18 19 20
+					     21>;
+				brcm,function = <6>; /* alt2 */
+				brcm,pull = <0>; /* no pull */
+			};
+		};
+	};
+};

arch/arm/boot/dts/overlays/gpio-ir-overlay.dts

@@ -36,8 +36,7 @@
         __overrides__ {
                 // parameters
                 gpio_pin =      <&gpio_ir>,"gpios:4",
-                                        <&gpio_ir_pins>,"brcm,pins:0",
-                                        <&gpio_ir_pins>,"brcm,pull:0";  // pin number
+                                        <&gpio_ir_pins>,"brcm,pins:0";  // pin number
                 gpio_pull = <&gpio_ir_pins>,"brcm,pull:0";              // pull-up/down state
 
                 rc-map-name = <&gpio_ir>,"linux,rc-map-name";           // default rc map

arch/arm/boot/dts/overlays/hifiberry-dacplus-overlay.dts

@@ -41,7 +41,7 @@
 
 	fragment@3 {
 		target = <&sound>;
-		frag3: __overlay__ {
+		hifiberry_dacplus: __overlay__ {
 			compatible = "hifiberry,hifiberry-dacplus";
 			i2s-controller = <&i2s>;
 			status = "okay";
@@ -49,6 +49,8 @@
 	};
 
 	__overrides__ {
-		24db_digital_gain = <&frag3>,"hifiberry,24db_digital_gain?";
+		24db_digital_gain =
+			<&hifiberry_dacplus>,"hifiberry,24db_digital_gain?";
+		slave = <&hifiberry_dacplus>,"hifiberry-dacplus,slave?";
 	};
 };

arch/arm/boot/dts/overlays/hifiberry-digi-pro-overlay.dts

@@ -0,0 +1,41 @@
+// Definitions for HiFiBerry Digi Pro
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&i2s>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&i2c1>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			wm8804@3b {
+				#sound-dai-cells = <0>;
+				compatible = "wlf,wm8804";
+				reg = <0x3b>;
+				status = "okay";
+			};
+		};
+	};
+
+	fragment@2 {
+		target = <&sound>;
+		__overlay__ {
+			compatible = "hifiberry,hifiberry-digi";
+			i2s-controller = <&i2s>;
+			status = "okay";
+			clock44-gpio = <&gpio 5 0>;
+			clock48-gpio = <&gpio 6 0>;
+		};
+	};
+};

arch/arm/boot/dts/overlays/i2c-gpio-overlay.dts

@@ -19,6 +19,21 @@
 			};
 		};
 	};
+
+	fragment@1 {
+		target-path = "/aliases";
+		__overlay__ {
+			i2c_gpio = "/i2c@0";
+		};
+	};
+
+	fragment@2 {
+		target-path = "/__symbols__";
+		__overlay__ {
+			i2c_gpio = "/i2c@0";
+		};
+	};
+
 	__overrides__ {
 		i2c_gpio_sda = <&i2c_gpio>,"gpios:4";
 		i2c_gpio_scl = <&i2c_gpio>,"gpios:16";

arch/arm/boot/dts/overlays/i2c-mux-overlay.dts

@@ -0,0 +1,139 @@
+// Umbrella I2C Mux overlay
+
+/dts-v1/;
+/plugin/;
+
+/{
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&i2c_arm>;
+		__dormant__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			pca9542: mux@70 {
+				compatible = "nxp,pca9542";
+				reg = <0x70>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+				i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+			};
+		};
+	};
+
+	fragment@1 {
+		target = <&i2c_arm>;
+		__dormant__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			pca9545: mux@70 {
+				compatible = "nxp,pca9545";
+				reg = <0x70>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+				i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+				i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+				i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+			};
+		};
+	};
+
+	fragment@2 {
+		target = <&i2c_arm>;
+		__dormant__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			pca9548: mux@70 {
+				compatible = "nxp,pca9548";
+				reg = <0x70>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+				i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+				i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+				i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+				i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+				i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+				i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+				i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+		};
+	};
+
+	__overrides__ {
+		pca9542 = <0>, "+0";
+		pca9545 = <0>, "+1";
+		pca9548 = <0>, "+2";
+
+		addr =  <&pca9542>,"reg:0",
+			<&pca9545>,"reg:0",
+			<&pca9548>,"reg:0";
+	};
+};

arch/arm/boot/dts/overlays/i2c-mux-pca9548a-overlay.dts

@@ -1,67 +0,0 @@
-// Definitions for NXP PCA9548A I2C mux on ARM I2C bus.
-/dts-v1/;
-/plugin/;
-
-/{
-	compatible = "brcm,bcm2708";
-
-	fragment@0 {
-		target = <&i2c_arm>;
-		__overlay__ {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			status = "okay";
-
-			i2cmux: mux@70 {
-				compatible = "nxp,pca9548";
-				reg = <0x70>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				i2c@0 {
-					#address-cells = <1>;
-					#size-cells = <0>;
-					reg = <0>;
-				};
-				i2c@1 {
-					#address-cells = <1>;
-					#size-cells = <0>;
-					reg = <1>;
-				};
-				i2c@2 {
-					#address-cells = <1>;
-					#size-cells = <0>;
-					reg = <2>;
-				};
-				i2c@3 {
-					#address-cells = <1>;
-					#size-cells = <0>;
-					reg = <3>;
-				};
-				i2c@4 {
-					#address-cells = <1>;
-					#size-cells = <0>;
-					reg = <4>;
-				};
-				i2c@5 {
-					#address-cells = <1>;
-					#size-cells = <0>;
-					reg = <5>;
-				};
-				i2c@6 {
-					#address-cells = <1>;
-					#size-cells = <0>;
-					reg = <6>;
-				};
-				i2c@7 {
-					#address-cells = <1>;
-					#size-cells = <0>;
-					reg = <7>;
-				};
-			};
-		};
-	};
-	__overrides__ {
-		addr = <&i2cmux>,"reg:0";
-	};
-};

arch/arm/boot/dts/overlays/i2c-rtc-overlay.dts

@@ -65,5 +65,9 @@
 		pcf8523 = <&pcf8523>,"status";
 		pcf8563 = <&pcf8563>,"status";
 		trickle-resistor-ohms = <&ds1339>,"trickle-resistor-ohms:0";
+		wakeup-source = <&ds1339>,"wakeup-source?",
+				<&ds3231>,"wakeup-source?",
+				<&mcp7940x>,"wakeup-source?",
+				<&mcp7941x>,"wakeup-source?";
 	};
 };

arch/arm/boot/dts/overlays/iqaudio-dac-overlay.dts

@@ -30,10 +30,14 @@
 
 	fragment@2 {
 		target = <&sound>;
-		__overlay__ {
+		frag2: __overlay__ {
 			compatible = "iqaudio,iqaudio-dac";
 			i2s-controller = <&i2s>;
 			status = "okay";
 		};
 	};
+
+	__overrides__ {
+		24db_digital_gain = <&frag2>,"iqaudio,24db_digital_gain?";
+	};
 };

arch/arm/boot/dts/overlays/iqaudio-dacplus-overlay.dts

@@ -30,14 +30,17 @@
 
 	fragment@2 {
 		target = <&sound>;
-		frag2: __overlay__ {
+		iqaudio_dac: __overlay__ {
 			compatible = "iqaudio,iqaudio-dac";
 			i2s-controller = <&i2s>;
+			mute-gpios = <&gpio 22 0>;
 			status = "okay";
 		};
 	};
 
 	__overrides__ {
-		24db_digital_gain = <&frag2>,"iqaudio,24db_digital_gain?";
+		24db_digital_gain = <&iqaudio_dac>,"iqaudio,24db_digital_gain?";
+		auto_mute_amp = <&iqaudio_dac>,"iqaudio-dac,auto-mute-amp?";
+		unmute_amp = <&iqaudio_dac>,"iqaudio-dac,unmute-amp?";
 	};
 };

arch/arm/boot/dts/overlays/iqaudio-digi-wm8804-audio-overlay.dts

@@ -0,0 +1,47 @@
+// Definitions for IQAudIO Digi WM8804 audio board
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&i2s>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&i2c1>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			wm8804@3b {
+				#sound-dai-cells = <0>;
+				compatible = "wlf,wm8804";
+				reg = <0x3b>;
+				status = "okay";
+				// DVDD-supply = <&reg_3v3>;
+				// PVDD-supply = <&reg_3v3>;
+			};
+		};
+	};
+
+	fragment@2 {
+		target = <&sound>;
+		wm8804_digi: __overlay__ {
+			compatible = "iqaudio,wm8804-digi";
+			i2s-controller = <&i2s>;
+			status = "okay";
+		};
+	};
+
+	__overrides__ {
+		card_name = <&wm8804_digi>,"wm8804-digi,card-name";
+		dai_name = <&wm8804_digi>,"wm8804-digi,dai-name";
+		dai_stream_name = <&wm8804_digi>,"wm8804-digi,dai-stream-name";
+	};
+};

arch/arm/boot/dts/overlays/justboom-dac-overlay.dts

@@ -1,4 +1,4 @@
-// Definitions for BoomBerry DAC
+// Definitions for JustBoom DAC
 /dts-v1/;
 /plugin/;
 
@@ -31,13 +31,13 @@
 	fragment@2 {
 		target = <&sound>;
 		frag2: __overlay__ {
-			compatible = "boomberry,boomberry-dac";
+			compatible = "justboom,justboom-dac";
 			i2s-controller = <&i2s>;
 			status = "okay";
 		};
 	};
 
 	__overrides__ {
-		24db_digital_gain = <&frag2>,"boomberry,24db_digital_gain?";
+		24db_digital_gain = <&frag2>,"justboom,24db_digital_gain?";
 	};
 };

arch/arm/boot/dts/overlays/justboom-digi-overlay.dts

@@ -1,4 +1,4 @@
-// Definitions for BoomBerry Digi
+// Definitions for JustBoom Digi
 /dts-v1/;
 /plugin/;
 
@@ -31,7 +31,7 @@
 	fragment@2 {
 		target = <&sound>;
 		__overlay__ {
-			compatible = "boomberry,boomberry-digi";
+			compatible = "justboom,justboom-digi";
 			i2s-controller = <&i2s>;
 			status = "okay";
 		};

arch/arm/boot/dts/overlays/mcp23017-overlay.dts

@@ -0,0 +1,54 @@
+// Definitions for MCP23017 Gpio Extender from Microchip Semiconductor
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
+
+	fragment@0 {
+		target = <&i2c1>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&gpio>;
+		__overlay__ {
+			mcp23017_pins: mcp23017_pins {
+				brcm,pins = <4>;
+				brcm,function = <0>;
+			};
+		};
+	};
+
+	fragment@2 {
+		target = <&i2c1>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			mcp23017: mcp@20 {
+				compatible = "microchip,mcp23017";
+				reg = <0x20>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				#interrupt-cells=<2>;
+				interrupt-parent = <&gpio>;
+				interrupts = <4 2>;
+				interrupt-controller;
+				microchip,irq-mirror;
+
+				status = "okay";
+			};
+		};
+	};
+	
+	__overrides__ {
+		gpiopin = <&mcp23017_pins>,"brcm,pins:0",
+				<&mcp23017>,"interrupts:0";
+		addr = <&mcp23017>,"reg:0";
+	};
+};
+

arch/arm/boot/dts/overlays/mcp23s17-overlay.dts

@@ -0,0 +1,732 @@
+// Overlay for MCP23S08/17 GPIO Extenders from Microchip Semiconductor
+
+// dtparams:
+//     s08-spi<n>-<m>-present  - 4-bit integer, bitmap indicating MCP23S08 devices present on SPI<n>, CS#<m>.
+//     s17-spi<n>-<m>-present  - 8-bit integer, bitmap indicating MCP23S17 devices present on SPI<n>, CS#<m>.
+//     s08-spi<n>-<m>-int-gpio - integer, enables interrupts on a single MCP23S08 device on SPI<n>, CS#<m>, specifies the GPIO pin to which INT output is connected.
+//     s17-spi<n>-<m>-int-gpio - integer, enables mirrored interrupts on a single MCP23S17 device on SPI<n>, CS#<m>, specifies the GPIO pin to which either INTA or INTB output is connected.
+//
+// If devices are present on SPI1 or SPI2, those interfaces must be enabled with one of the spi1-1/2/3cs and/or spi2-1/2/3cs overlays.
+// If interrupts are enabled for a device on a given CS# on a SPI bus, that device must be the only one present on that SPI bus/CS#.
+//
+// Example 1: A single MCP23S17 device on SPI0, CS#0 with its SPI addr set to 0 and INTA output connected to GPIO25:
+// dtoverlay=mcp23s17:s17-spi0-0-present=1,s17-spi0-0-int-gpio=25
+//
+// Example 2: Two MCP23S08 devices on SPI1, CS#0 with their addrs set to 2 and 3. Three MCP23S17 devices on SPI1, CS#1 with their addrs set to 0, 1 and 7:
+// dtoverlay=spi1-2cs
+// dtoverlay=mcp23s17:s08-spi1-0-present=12,s17-spi1-1-present=131
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
+
+	// disable spi-dev on spi0.0
+	fragment@0 {
+		target = <&spidev0>;
+		__dormant__ {
+			status = "disabled";
+		};
+	};
+
+	// disable spi-dev on spi0.1
+	fragment@1 {
+		target = <&spidev1>;
+		__dormant__ {
+			status = "disabled";
+		};
+	};
+
+	// disable spi-dev on spi1.0
+	fragment@2 {
+		target-path = "spi1/spidev@0";
+		__dormant__ {
+			status = "disabled";
+		};
+	};
+
+	// disable spi-dev on spi1.1
+	fragment@3 {
+		target-path = "spi1/spidev@1";
+		__dormant__ {
+			status = "disabled";
+		};
+	};
+
+	// disable spi-dev on spi1.2
+	fragment@4 {
+		target-path = "spi1/spidev@2";
+		__dormant__ {
+			status = "disabled";
+		};
+	};
+
+	// disable spi-dev on spi2.0
+	fragment@5 {
+		target-path = "spi2/spidev@0";
+		__dormant__ {
+			status = "disabled";
+		};
+	};
+
+	// disable spi-dev on spi2.1
+	fragment@6 {
+		target-path = "spi2/spidev@1";
+		__dormant__ {
+			status = "disabled";
+		};
+	};
+
+	// disable spi-dev on spi2.2
+	fragment@7 {
+		target-path = "spi2/spidev@2";
+		__dormant__ {
+			status = "disabled";
+		};
+	};
+
+	// enable one or more mcp23s08s on spi0.0
+	fragment@8 {
+		target = <&spi0>;
+		__dormant__ {
+			status = "okay";
+                        #address-cells = <1>;
+                        #size-cells = <0>;
+			mcp23s08_00: mcp23s08@0 {
+				compatible = "microchip,mcp23s08";
+  				gpio-controller;
+  				#gpio-cells = <2>;
+    				microchip,spi-present-mask = <0x00>;  /* overwritten by mcp23s08-spi0-0-present parameter */
+     				reg = <0>;
+    				spi-max-frequency = <500000>;
+				status = "okay";
+				#interrupt-cells=<2>;
+				interrupts = <0 2>;  /* 1st word overwritten by mcp23s08-spi0-0-int-gpio parameter */
+			};
+		};
+	};
+
+	// enable one or more mcp23s08s on spi0.1
+	fragment@9 {
+		target = <&spi0>;
+		__dormant__ {
+			status = "okay";
+                        #address-cells = <1>;
+                        #size-cells = <0>;
+			mcp23s08_01: mcp23s08@1 {
+				compatible = "microchip,mcp23s08";
+  				gpio-controller;
+  				#gpio-cells = <2>;
+    				microchip,spi-present-mask = <0x00>;  /* overwritten by mcp23s08-spi0-1-present parameter */
+     				reg = <1>;
+    				spi-max-frequency = <500000>;
+				status = "okay";
+				#interrupt-cells=<2>;
+				interrupts = <0 2>;  /* 1st word overwritten by mcp23s08-spi0-1-int-gpio parameter */
+			};
+		};
+	};
+
+	// enable one or more mcp23s08s on spi1.0
+	fragment@10 {
+		target = <&spi1>;
+		__dormant__ {
+			status = "okay";
+                        #address-cells = <1>;
+                        #size-cells = <0>;
+			mcp23s08_10: mcp23s08@0 {
+				compatible = "microchip,mcp23s08";
+  				gpio-controller;
+  				#gpio-cells = <2>;
+    				microchip,spi-present-mask = <0x00>;  /* overwritten by mcp23s08-spi1-0-present parameter */
+     				reg = <0>;
+    				spi-max-frequency = <500000>;
+				status = "okay";
+				#interrupt-cells=<2>;
+				interrupts = <0 2>;  /* 1st word overwritten by mcp23s08-spi1-0-int-gpio parameter */
+			};
+		};
+	};
+
+	// enable one or more mcp23s08s on spi1.1
+	fragment@11 {
+		target = <&spi1>;
+		__dormant__ {
+			status = "okay";
+                        #address-cells = <1>;
+                        #size-cells = <0>;
+			mcp23s08_11: mcp23s08@1 {
+				compatible = "microchip,mcp23s08";
+  				gpio-controller;
+  				#gpio-cells = <2>;
+    				microchip,spi-present-mask = <0x00>;  /* overwritten by mcp23s08-spi1-1-present parameter */
+     				reg = <1>;
+    				spi-max-frequency = <500000>;
+				status = "okay";
+				#interrupt-cells=<2>;
+				interrupts = <0 2>;  /* 1st word overwritten by mcp23s08-spi1-1-int-gpio parameter */
+			};
+		};
+	};
+
+	// enable one or more mcp23s08s on spi1.2
+	fragment@12 {
+		target = <&spi1>;
+		__dormant__ {
+			status = "okay";
+                        #address-cells = <1>;
+                        #size-cells = <0>;
+			mcp23s08_12: mcp23s08@2 {
+				compatible = "microchip,mcp23s08";
+  				gpio-controller;
+  				#gpio-cells = <2>;
+    				microchip,spi-present-mask = <0x00>;  /* overwritten by mcp23s08-spi1-2-present parameter */
+     				reg = <2>;
+    				spi-max-frequency = <500000>;
+				status = "okay";
+				#interrupt-cells=<2>;
+				interrupts = <0 2>;  /* 1st word overwritten by mcp23s08-spi1-2-int-gpio parameter */
+			};
+		};
+	};
+
+	// enable one or more mcp23s08s on spi2.0
+	fragment@13 {
+		target = <&spi2>;
+		__dormant__ {
+			status = "okay";
+                        #address-cells = <1>;
+                        #size-cells = <0>;
+			mcp23s08_20: mcp23s08@0 {
+				compatible = "microchip,mcp23s08";
+  				gpio-controller;
+  				#gpio-cells = <2>;
+    				microchip,spi-present-mask = <0x00>;  /* overwritten by mcp23s08-spi2-0-present parameter */
+     				reg = <0>;
+    				spi-max-frequency = <500000>;
+				status = "okay";
+				#interrupt-cells=<2>;
+				interrupts = <0 2>;  /* 1st word overwritten by mcp23s08-spi2-0-int-gpio parameter */
+			};
+		};
+	};
+
+	// enable one or more mcp23s08s on spi2.1
+	fragment@14 {
+		target = <&spi2>;
+		__dormant__ {
+			status = "okay";
+                        #address-cells = <1>;
+                        #size-cells = <0>;
+			mcp23s08_21: mcp23s08@1 {
+				compatible = "microchip,mcp23s08";
+  				gpio-controller;
+  				#gpio-cells = <2>;
+    				microchip,spi-present-mask = <0x00>;  /* overwritten by mcp23s08-spi2-1-present parameter */
+     				reg = <1>;
+    				spi-max-frequency = <500000>;
+				status = "okay";
+				#interrupt-cells=<2>;
+				interrupts = <0 2>;  /* 1st word overwritten by mcp23s08-spi2-1-int-gpio parameter */
+			};
+		};
+	};
+
+	// enable one or more mcp23s08s on spi2.2
+	fragment@15 {
+		target = <&spi2>;
+		__dormant__ {
+			status = "okay";
+                        #address-cells = <1>;
+                        #size-cells = <0>;
+			mcp23s08_22: mcp23s08@2 {
+				compatible = "microchip,mcp23s08";
+  				gpio-controller;
+  				#gpio-cells = <2>;
+    				microchip,spi-present-mask = <0x00>;  /* overwritten by mcp23s08-spi2-2-present parameter */
+     				reg = <2>;
+    				spi-max-frequency = <500000>;
+				status = "okay";
+				#interrupt-cells=<2>;
+				interrupts = <0 2>;  /* 1st word overwritten by mcp23s08-spi2-2-int-gpio parameter */
+			};
+		};
+	};
+
+	// enable one or more mcp23s17s on spi0.0
+	fragment@16 {
+		target = <&spi0>;
+		__dormant__ {
+			status = "okay";
+                        #address-cells = <1>;
+                        #size-cells = <0>;
+			mcp23s17_00: mcp23s17@0 {
+				compatible = "microchip,mcp23s17";
+  				gpio-controller;
+  				#gpio-cells = <2>;
+    				microchip,spi-present-mask = <0x00>;  /* overwritten by mcp23s17-spi0-0-present parameter */
+     				reg = <0>;
+    				spi-max-frequency = <500000>;
+				status = "okay";
+				#interrupt-cells=<2>;
+				interrupts = <0 2>;  /* 1st word overwritten by mcp23s17-spi0-0-int-gpio parameter */
+			};
+		};
+	};
+
+	// enable one or more mcp23s17s on spi0.1
+	fragment@17 {
+		target = <&spi0>;
+		__dormant__ {
+			status = "okay";
+                        #address-cells = <1>;
+                        #size-cells = <0>;
+			mcp23s17_01: mcp23s17@1 {
+				compatible = "microchip,mcp23s17";
+  				gpio-controller;
+  				#gpio-cells = <2>;
+    				microchip,spi-present-mask = <0x00>;  /* overwritten by mcp23s17-spi0-1-present parameter */
+     				reg = <1>;
+    				spi-max-frequency = <500000>;
+				status = "okay";
+				#interrupt-cells=<2>;
+				interrupts = <0 2>;  /* 1st word overwritten by mcp23s17-spi0-1-int-gpio parameter */
+			};
+		};
+	};
+
+	// enable one or more mcp23s17s on spi1.0
+	fragment@18 {
+		target = <&spi1>;
+		__dormant__ {
+			status = "okay";
+                        #address-cells = <1>;
+                        #size-cells = <0>;
+			mcp23s17_10: mcp23s17@0 {
+				compatible = "microchip,mcp23s17";
+  				gpio-controller;
+  				#gpio-cells = <2>;
+    				microchip,spi-present-mask = <0x00>;  /* overwritten by mcp23s17-spi1-0-present parameter */
+     				reg = <0>;
+    				spi-max-frequency = <500000>;
+				status = "okay";
+				#interrupt-cells=<2>;
+				interrupts = <0 2>;  /* 1st word overwritten by mcp23s17-spi1-0-int-gpio parameter */
+			};
+		};
+	};
+
+	// enable one or more mcp23s17s on spi1.1
+	fragment@19 {
+		target = <&spi1>;
+		__dormant__ {
+			status = "okay";
+                        #address-cells = <1>;
+                        #size-cells = <0>;
+			mcp23s17_11: mcp23s17@1 {
+				compatible = "microchip,mcp23s17";
+  				gpio-controller;
+  				#gpio-cells = <2>;
+    				microchip,spi-present-mask = <0x00>;  /* overwritten by mcp23s17-spi1-1-present parameter */
+     				reg = <1>;
+    				spi-max-frequency = <500000>;
+				status = "okay";
+				#interrupt-cells=<2>;
+				interrupts = <0 2>;  /* 1st word overwritten by mcp23s17-spi1-1-int-gpio parameter */
+			};
+		};
+	};
+
+	// enable one or more mcp23s17s on spi1.2
+	fragment@20 {
+		target = <&spi1>;
+		__dormant__ {
+			status = "okay";
+                        #address-cells = <1>;
+                        #size-cells = <0>;
+			mcp23s17_12: mcp23s17@2 {
+				compatible = "microchip,mcp23s17";
+  				gpio-controller;
+  				#gpio-cells = <2>;
+    				microchip,spi-present-mask = <0x00>;  /* overwritten by mcp23s17-spi1-2-present parameter */
+     				reg = <2>;
+    				spi-max-frequency = <500000>;
+				status = "okay";
+				#interrupt-cells=<2>;
+				interrupts = <0 2>;  /* 1st word overwritten by mcp23s17-spi1-2-int-gpio parameter */
+			};
+		};
+	};
+
+	// enable one or more mcp23s17s on spi2.0
+	fragment@21 {
+		target = <&spi2>;
+		__dormant__ {
+			status = "okay";
+                        #address-cells = <1>;
+                        #size-cells = <0>;
+			mcp23s17_20: mcp23s17@0 {
+				compatible = "microchip,mcp23s17";
+  				gpio-controller;
+  				#gpio-cells = <2>;
+    				microchip,spi-present-mask = <0x00>;  /* overwritten by mcp23s17-spi2-0-present parameter */
+     				reg = <0>;
+    				spi-max-frequency = <500000>;
+				status = "okay";
+				#interrupt-cells=<2>;
+				interrupts = <0 2>;  /* 1st word overwritten by mcp23s17-spi2-0-int-gpio parameter */
+			};
+		};
+	};
+
+	// enable one or more mcp23s17s on spi2.1
+	fragment@22 {
+		target = <&spi2>;
+		__dormant__ {
+			status = "okay";
+                        #address-cells = <1>;
+                        #size-cells = <0>;
+			mcp23s17_21: mcp23s17@1 {
+				compatible = "microchip,mcp23s17";
+  				gpio-controller;
+  				#gpio-cells = <2>;
+    				microchip,spi-present-mask = <0x00>;  /* overwritten by mcp23s17-spi2-1-present parameter */
+     				reg = <1>;
+    				spi-max-frequency = <500000>;
+				status = "okay";
+				#interrupt-cells=<2>;
+				interrupts = <0 2>;  /* 1st word overwritten by mcp23s17-spi2-1-int-gpio parameter */
+			};
+		};
+	};
+
+	// enable one or more mcp23s17s on spi2.2
+	fragment@23 {
+		target = <&spi2>;
+		__dormant__ {
+			status = "okay";
+                        #address-cells = <1>;
+                        #size-cells = <0>;
+			mcp23s17_22: mcp23s17@2 {
+				compatible = "microchip,mcp23s17";
+  				gpio-controller;
+  				#gpio-cells = <2>;
+    				microchip,spi-present-mask = <0x00>;  /* overwritten by mcp23s17-spi2-2-present parameter */
+     				reg = <2>;
+    				spi-max-frequency = <500000>;
+				status = "okay";
+				#interrupt-cells=<2>;
+				interrupts = <0 2>;  /* 1st word overwritten by mcp23s17-spi2-2-int-gpio parameter */
+			};
+		};
+	};
+
+	// Configure GPIO pin connected to INT(A/B) output of mcp23s08/17 on spi0.0 as a input with no pull-up/down
+	fragment@24 {
+		target = <&gpio>;
+		__dormant__ {
+			spi0_0_int_pins: spi0_0_int_pins {
+				brcm,pins = <0>;  /* overwritten by mcp23s08/17-spi0-0-int-gpio parameter */
+				brcm,function = <0>;
+				brcm,pull = <0>;
+			};
+		};
+	};
+
+	// Configure GPIO pin connected to INT(A/B) output of mcp23s08/17 on spi0.1 as a input with no pull-up/down
+	fragment@25 {
+		target = <&gpio>;
+		__dormant__ {
+			spi0_1_int_pins: spi0_1_int_pins {
+				brcm,pins = <0>;  /* overwritten by mcp23s08/17-spi0-1-int-gpio parameter */
+				brcm,function = <0>;
+				brcm,pull = <0>;
+			};
+		};
+	};
+
+	// Configure GPIO pin connected to INT(A/B) output of mcp23s08/17 on spi1.0 as a input with no pull-up/down
+	fragment@26 {
+		target = <&gpio>;
+		__dormant__ {
+			spi1_0_int_pins: spi1_0_int_pins {
+				brcm,pins = <0>;  /* overwritten by mcp23s08/17-spi1-0-int-gpio parameter */
+				brcm,function = <0>;
+				brcm,pull = <0>;
+			};
+		};
+	};
+
+	// Configure GPIO pin connected to INT(A/B) output of mcp23s08/17 on spi1.1 as a input with no pull-up/down
+	fragment@27 {
+		target = <&gpio>;
+		__dormant__ {
+			spi1_1_int_pins: spi1_1_int_pins {
+				brcm,pins = <0>;  /* overwritten by mcp23s08/17-spi1-1-int-gpio parameter */
+				brcm,function = <0>;
+				brcm,pull = <0>;
+			};
+		};
+	};
+
+	// Configure GPIO pin connected to INT(A/B) output of mcp23s08/17 on spi1.2 as a input with no pull-up/down
+	fragment@28 {
+		target = <&gpio>;
+		__dormant__ {
+			spi1_2_int_pins: spi1_2_int_pins {
+				brcm,pins = <0>;  /* overwritten by mcp23s08/17-spi1-2-int-gpio parameter */
+				brcm,function = <0>;
+				brcm,pull = <0>;
+			};
+		};
+	};
+
+	// Configure GPIO pin connected to INT(A/B) output of mcp23s08/17 on spi2.0 as a input with no pull-up/down
+	fragment@29 {
+		target = <&gpio>;
+		__dormant__ {
+			spi2_0_int_pins: spi2_0_int_pins {
+				brcm,pins = <0>;  /* overwritten by mcp23s08/17-spi2-0-int-gpio parameter */
+				brcm,function = <0>;
+				brcm,pull = <0>;
+			};
+		};
+	};
+
+	// Configure GPIO pin connected to INT(A/B) output of mcp23s08/17 on spi2.1 as a input with no pull-up/down
+	fragment@30 {
+		target = <&gpio>;
+		__dormant__ {
+			spi2_1_int_pins: spi2_1_int_pins {
+				brcm,pins = <0>;  /* overwritten by mcp23s08/17-spi2-1-int-gpio parameter */
+				brcm,function = <0>;
+				brcm,pull = <0>;
+			};
+		};
+	};
+
+	// Configure GPIO pin connected to INT(A/B) output of mcp23s08/17 on spi2.2 as a input with no pull-up/down
+	fragment@31 {
+		target = <&gpio>;
+		__dormant__ {
+			spi2_2_int_pins: spi2_2_int_pins {
+				brcm,pins = <0>;  /* overwritten by mcp23s08/17-spi2-2-int-gpio parameter */
+				brcm,function = <0>;
+				brcm,pull = <0>;
+			};
+		};
+	};
+
+	// Enable interrupts for a mcp23s08 on spi0.0.
+	// Use default active low interrupt signalling.
+	fragment@32 {
+		target = <&mcp23s08_00>;
+		__dormant__ {
+			interrupt-parent = <&gpio>;
+			interrupt-controller;
+		};
+	};
+
+	// Enable interrupts for a mcp23s08 on spi0.1.
+	// Use default active low interrupt signalling.
+	fragment@33 {
+		target = <&mcp23s08_01>;
+		__dormant__ {
+			interrupt-parent = <&gpio>;
+			interrupt-controller;
+		};
+	};
+
+	// Enable interrupts for a mcp23s08 on spi1.0.
+	// Use default active low interrupt signalling.
+	fragment@34 {
+		target = <&mcp23s08_10>;
+		__dormant__ {
+			interrupt-parent = <&gpio>;
+			interrupt-controller;
+		};
+	};
+
+	// Enable interrupts for a mcp23s08 on spi1.1.
+	// Use default active low interrupt signalling.
+	fragment@35 {
+		target = <&mcp23s08_11>;
+		__dormant__ {
+			interrupt-parent = <&gpio>;
+			interrupt-controller;
+		};
+	};
+
+	// Enable interrupts for a mcp23s08 on spi1.2.
+	// Use default active low interrupt signalling.
+	fragment@36 {
+		target = <&mcp23s08_12>;
+		__dormant__ {
+			interrupt-parent = <&gpio>;
+			interrupt-controller;
+		};
+	};
+
+	// Enable interrupts for a mcp23s08 on spi2.0.
+	// Use default active low interrupt signalling.
+	fragment@37 {
+		target = <&mcp23s08_20>;
+		__dormant__ {
+			interrupt-parent = <&gpio>;
+			interrupt-controller;
+		};
+	};
+
+	// Enable interrupts for a mcp23s08 on spi2.1.
+	// Use default active low interrupt signalling.
+	fragment@38 {
+		target = <&mcp23s08_21>;
+		__dormant__ {
+			interrupt-parent = <&gpio>;
+			interrupt-controller;
+		};
+	};
+
+	// Enable interrupts for a mcp23s08 on spi2.2.
+	// Use default active low interrupt signalling.
+	fragment@39 {
+		target = <&mcp23s08_22>;
+		__dormant__ {
+			interrupt-parent = <&gpio>;
+			interrupt-controller;
+		};
+	};
+
+	// Enable interrupts for a mcp23s17 on spi0.0.
+	// Enable mirroring so that either INTA or INTB output of mcp23s17 can be connected to the GPIO pin.
+	// Use default active low interrupt signalling.
+	fragment@40 {
+		target = <&mcp23s17_00>;
+		__dormant__ {
+			interrupt-parent = <&gpio>;
+			interrupt-controller;
+			microchip,irq-mirror;
+		};
+	};
+
+	// Enable interrupts for a mcp23s17 on spi0.1.
+	// Enable mirroring so that either INTA or INTB output of mcp23s17 can be connected to the GPIO pin.
+	// Configure INTA/B outputs of mcp23s08/17 as active low.
+	fragment@41 {
+		target = <&mcp23s17_01>;
+		__dormant__ {
+			interrupt-parent = <&gpio>;
+			interrupt-controller;
+			microchip,irq-mirror;
+		};
+	};
+
+	// Enable interrupts for a mcp23s17 on spi1.0.
+	// Enable mirroring so that either INTA or INTB output of mcp23s17 can be connected to the GPIO pin.
+	// Configure INTA/B outputs of mcp23s08/17 as active low.
+	fragment@42 {
+		target = <&mcp23s17_10>;
+		__dormant__ {
+			interrupt-parent = <&gpio>;
+			interrupt-controller;
+			microchip,irq-mirror;
+		};
+	};
+
+	// Enable interrupts for a mcp23s17 on spi1.1.
+	// Enable mirroring so that either INTA or INTB output of mcp23s17 can be connected to the GPIO pin.
+	// Configure INTA/B outputs of mcp23s08/17 as active low.
+	fragment@43 {
+		target = <&mcp23s17_11>;
+		__dormant__ {
+			interrupt-parent = <&gpio>;
+			interrupt-controller;
+			microchip,irq-mirror;
+		};
+	};
+
+	// Enable interrupts for a mcp23s17 on spi1.2.
+	// Enable mirroring so that either INTA or INTB output of mcp23s17 can be connected to the GPIO pin.
+	// Configure INTA/B outputs of mcp23s08/17 as active low.
+	fragment@44 {
+		target = <&mcp23s17_12>;
+		__dormant__ {
+			interrupt-parent = <&gpio>;
+			interrupt-controller;
+			microchip,irq-mirror;
+		};
+	};
+
+	// Enable interrupts for a mcp23s17 on spi2.0.
+	// Enable mirroring so that either INTA or INTB output of mcp23s17 can be connected to the GPIO pin.
+	// Configure INTA/B outputs of mcp23s08/17 as active low.
+	fragment@45 {
+		target = <&mcp23s17_20>;
+		__dormant__ {
+			interrupt-parent = <&gpio>;
+			interrupt-controller;
+			microchip,irq-mirror;
+		};
+	};
+
+	// Enable interrupts for a mcp23s17 on spi2.1.
+	// Enable mirroring so that either INTA or INTB output of mcp23s17 can be connected to the GPIO pin.
+	// Configure INTA/B outputs of mcp23s08/17 as active low.
+	fragment@46 {
+		target = <&mcp23s17_21>;
+		__dormant__ {
+			interrupt-parent = <&gpio>;
+			interrupt-controller;
+			microchip,irq-mirror;
+		};
+	};
+
+	// Enable interrupts for a mcp23s17 on spi2.2.
+	// Enable mirroring so that either INTA or INTB output of mcp23s17 can be connected to the GPIO pin.
+	// Configure INTA/B outputs of mcp23s08/17 as active low.
+	fragment@47 {
+		target = <&mcp23s17_22>;
+		__dormant__ {
+			interrupt-parent = <&gpio>;
+			interrupt-controller;
+			microchip,irq-mirror;
+		};
+	};
+
+	__overrides__ {
+		s08-spi0-0-present = <0>,"+0+8",  <&mcp23s08_00>,"microchip,spi-present-mask:0";
+		s08-spi0-1-present = <0>,"+1+9",  <&mcp23s08_01>,"microchip,spi-present-mask:0";
+		s08-spi1-0-present = <0>,"+2+10", <&mcp23s08_10>,"microchip,spi-present-mask:0";
+		s08-spi1-1-present = <0>,"+3+11", <&mcp23s08_11>,"microchip,spi-present-mask:0";
+		s08-spi1-2-present = <0>,"+4+12", <&mcp23s08_12>,"microchip,spi-present-mask:0";
+		s08-spi2-0-present = <0>,"+5+13", <&mcp23s08_20>,"microchip,spi-present-mask:0";
+		s08-spi2-1-present = <0>,"+6+14", <&mcp23s08_21>,"microchip,spi-present-mask:0";
+		s08-spi2-2-present = <0>,"+7+15", <&mcp23s08_22>,"microchip,spi-present-mask:0";
+		s17-spi0-0-present = <0>,"+0+16", <&mcp23s17_00>,"microchip,spi-present-mask:0";
+		s17-spi0-1-present = <0>,"+1+17", <&mcp23s17_01>,"microchip,spi-present-mask:0";
+		s17-spi1-0-present = <0>,"+2+18", <&mcp23s17_10>,"microchip,spi-present-mask:0";
+		s17-spi1-1-present = <0>,"+3+19", <&mcp23s17_11>,"microchip,spi-present-mask:0";
+		s17-spi1-2-present = <0>,"+4+20", <&mcp23s17_12>,"microchip,spi-present-mask:0";
+		s17-spi2-0-present = <0>,"+5+21", <&mcp23s17_20>,"microchip,spi-present-mask:0";
+		s17-spi2-1-present = <0>,"+6+22", <&mcp23s17_21>,"microchip,spi-present-mask:0";
+		s17-spi2-2-present = <0>,"+7+23", <&mcp23s17_22>,"microchip,spi-present-mask:0";
+		s08-spi0-0-int-gpio = <0>,"+24+32", <&spi0_0_int_pins>,"brcm,pins:0", <&mcp23s08_00>,"interrupts:0";
+		s08-spi0-1-int-gpio = <0>,"+25+33", <&spi0_1_int_pins>,"brcm,pins:0", <&mcp23s08_01>,"interrupts:0";
+		s08-spi1-0-int-gpio = <0>,"+26+34", <&spi1_0_int_pins>,"brcm,pins:0", <&mcp23s08_10>,"interrupts:0";
+		s08-spi1-1-int-gpio = <0>,"+27+35", <&spi1_1_int_pins>,"brcm,pins:0", <&mcp23s08_11>,"interrupts:0";
+		s08-spi1-2-int-gpio = <0>,"+28+36", <&spi1_2_int_pins>,"brcm,pins:0", <&mcp23s08_12>,"interrupts:0";
+		s08-spi2-0-int-gpio = <0>,"+29+37", <&spi2_0_int_pins>,"brcm,pins:0", <&mcp23s08_20>,"interrupts:0";
+		s08-spi2-1-int-gpio = <0>,"+30+38", <&spi2_1_int_pins>,"brcm,pins:0", <&mcp23s08_21>,"interrupts:0";
+		s08-spi2-2-int-gpio = <0>,"+31+39", <&spi2_2_int_pins>,"brcm,pins:0", <&mcp23s08_22>,"interrupts:0";
+		s17-spi0-0-int-gpio = <0>,"+24+40", <&spi0_0_int_pins>,"brcm,pins:0", <&mcp23s17_00>,"interrupts:0";
+		s17-spi0-1-int-gpio = <0>,"+25+41", <&spi0_1_int_pins>,"brcm,pins:0", <&mcp23s17_01>,"interrupts:0";
+		s17-spi1-0-int-gpio = <0>,"+26+42", <&spi1_0_int_pins>,"brcm,pins:0", <&mcp23s17_10>,"interrupts:0";
+		s17-spi1-1-int-gpio = <0>,"+27+43", <&spi1_1_int_pins>,"brcm,pins:0", <&mcp23s17_11>,"interrupts:0";
+		s17-spi1-2-int-gpio = <0>,"+28+44", <&spi1_2_int_pins>,"brcm,pins:0", <&mcp23s17_12>,"interrupts:0";
+		s17-spi2-0-int-gpio = <0>,"+29+45", <&spi2_0_int_pins>,"brcm,pins:0", <&mcp23s17_20>,"interrupts:0";
+		s17-spi2-1-int-gpio = <0>,"+30+46", <&spi2_1_int_pins>,"brcm,pins:0", <&mcp23s17_21>,"interrupts:0";
+		s17-spi2-2-int-gpio = <0>,"+31+47", <&spi2_2_int_pins>,"brcm,pins:0", <&mcp23s17_22>,"interrupts:0";
+	};
+};
+

arch/arm/boot/dts/overlays/pitft35-resistive-overlay.dts

@@ -0,0 +1,121 @@
+/*
+ * Device Tree overlay for Adafruit PiTFT 3.5" resistive touch screen
+ *
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
+
+	fragment@0 {
+		target = <&spi0>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&spidev0>;
+		__overlay__ {
+			status = "disabled";
+		};
+	};
+
+	fragment@2 {
+		target = <&spidev1>;
+		__overlay__ {
+			status = "disabled";
+		};
+	};
+
+	fragment@3 {
+		target = <&gpio>;
+		__overlay__ {
+			pitft_pins: pitft_pins {
+				brcm,pins = <24 25>;
+				brcm,function = <0 1>; /* in out */
+				brcm,pull = <2 0>; /* pullup none */
+			};
+		};
+	};
+
+	fragment@4 {
+		target = <&spi0>;
+		__overlay__ {
+			/* needed to avoid dtc warning */
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			pitft: pitft@0{
+				compatible = "himax,hx8357d";
+				reg = <0>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pitft_pins>;
+
+				spi-max-frequency = <32000000>;
+				rotate = <90>;
+				fps = <25>;
+				bgr;
+				buswidth = <8>;
+				dc-gpios = <&gpio 25 0>;
+				debug = <0>;
+			};
+
+			pitft_ts@1 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stmpe610";
+				reg = <1>;
+
+				spi-max-frequency = <500000>;
+				irq-gpio = <&gpio 24 0x2>; /* IRQF_TRIGGER_FALLING */
+				interrupts = <24 2>; /* high-to-low edge triggered */
+				interrupt-parent = <&gpio>;
+				interrupt-controller;
+
+				stmpe_touchscreen {
+					compatible = "st,stmpe-ts";
+					st,sample-time = <4>;
+					st,mod-12b = <1>;
+					st,ref-sel = <0>;
+					st,adc-freq = <2>;
+					st,ave-ctrl = <3>;
+					st,touch-det-delay = <4>;
+					st,settling = <2>;
+					st,fraction-z = <7>;
+					st,i-drive = <0>;
+				};
+
+				stmpe_gpio: stmpe_gpio {
+					#gpio-cells = <2>;
+					compatible = "st,stmpe-gpio";
+					/*
+					 * only GPIO2 is wired/available
+					 * and it is wired to the backlight
+					 */
+					st,norequest-mask = <0x7b>;
+				};
+			};
+		};
+	};
+
+	fragment@5 {
+		target-path = "/soc";
+		__overlay__ {
+			backlight {
+				compatible = "gpio-backlight";
+				gpios = <&stmpe_gpio 2 0>;
+				default-on;
+			};
+		};
+	};
+
+	__overrides__ {
+		speed =   <&pitft>,"spi-max-frequency:0";
+		rotate =  <&pitft>,"rotate:0";
+		fps =     <&pitft>,"fps:0";
+		debug =   <&pitft>,"debug:0";
+	};
+};

arch/arm/boot/dts/overlays/pps-gpio-overlay.dts

@@ -30,5 +30,6 @@
 	__overrides__ {
 		gpiopin = <&pps>,"gpios:4",
 			  <&pps_pins>,"brcm,pins:0";
+		assert_falling_edge = <&pps>,"assert-falling-edge?";
 	};
 };

arch/arm/boot/dts/overlays/rpi-dac-overlay.dts

@@ -13,7 +13,7 @@
 	};
 
 	fragment@1 {
-		target = <&soc>;
+		target-path = "/";
 		__overlay__ {
 			pcm1794a-codec {
 				#sound-dai-cells = <0>;

arch/arm/boot/dts/overlays/rra-digidac1-wm8741-audio-overlay.dts

@@ -0,0 +1,81 @@
+// Definitions for RRA DigiDAC1 Audio card
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target-path = "/";
+		__overlay__ {
+			aliases {
+				ldo0 = &ldo0;
+				ldo1 = &ldo1;
+			};
+		};
+	};
+
+	fragment@1 {
+		target-path = "/soc";
+		__overlay__ {
+
+			ldo1: ldo1 {
+				compatible = "regulator-fixed";
+				regulator-name = "DC_5V";
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5000000>;
+				regulator-always-on;
+			};
+
+			ldo0: ldo0 {
+				compatible = "regulator-fixed";
+				regulator-name = "DC_3V3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+		};
+	};
+
+	fragment@2 {
+		target = <&i2s>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@3 {
+		target = <&i2c1>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			wm8804@3b {
+				#sound-dai-cells = <0>;
+				compatible = "wlf,wm8804";
+				reg = <0x3b>;
+				status = "okay";
+				PVDD-supply = <&ldo0>;
+				DVDD-supply = <&ldo0>;
+			};
+
+			wm8742: wm8741@1a {
+				compatible = "wlf,wm8741";
+				reg = <0x1a>;
+				status = "okay";
+				AVDD-supply = <&ldo1>;
+				DVDD-supply = <&ldo0>;
+			};
+		};
+	};
+
+	fragment@4 {
+		target = <&sound>;
+		__overlay__ {
+			compatible = "rra,digidac1-soundcard";
+			i2s-controller = <&i2s>;
+			status = "okay";
+		};
+	};
+};

arch/arm/boot/dts/overlays/sc16is750-i2c-overlay.dts

@@ -0,0 +1,37 @@
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
+
+	fragment@0 {
+		target = <&i2c_arm>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			sc16is750: sc16is750@48 {
+				compatible = "nxp,sc16is750";
+				reg = <0x48>; /* address */
+				clocks = <&sc16is750_clk>;
+				interrupt-parent = <&gpio>;
+				interrupts = <24 2>; /* IRQ_TYPE_EDGE_FALLING */
+				#gpio-cells = <2>;
+
+				sc16is750_clk: sc16is750_clk {
+					compatible = "fixed-clock";
+					#clock-cells = <0>;
+					clock-frequency = <14745600>;
+				};
+			};
+		};
+	};
+
+
+	__overrides__ {
+		int_pin = <&sc16is750>,"interrupts:0";
+		addr = <&sc16is750>,"reg:0";
+	};
+
+};

arch/arm/boot/dts/overlays/sc16is752-spi1-overlay.dts

@@ -0,0 +1,61 @@
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
+
+	fragment@0 {
+		target = <&gpio>;
+		__overlay__ {
+			spi1_pins: spi1_pins {
+				brcm,pins = <19 20 21>;
+				brcm,function = <3>; /* alt4 */
+			};
+
+			spi1_cs_pins: spi1_cs_pins {
+				brcm,pins = <18>;
+				brcm,function = <1>; /* output */
+			};
+		};
+	};
+
+	fragment@1 {
+		target = <&spi1>;
+		frag1: __overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&spi1_pins &spi1_cs_pins>;
+			cs-gpios = <&gpio 18 1>;
+			status = "okay";
+
+			sc16is752: sc16is752@0 {
+				compatible = "nxp,sc16is752";
+				reg = <0>; /* CE0 */
+				clocks = <&sc16is752_clk>;
+				interrupt-parent = <&gpio>;
+				interrupts = <24 2>; /* IRQ_TYPE_EDGE_FALLING */
+				#gpio-controller;
+				#gpio-cells = <2>;
+				spi-max-frequency = <4000000>;
+
+				sc16is752_clk: sc16is752_clk {
+					compatible = "fixed-clock";
+					#clock-cells = <0>;
+					clock-frequency = <14745600>;
+				};
+			};
+		};
+	};
+
+	fragment@2 {
+		target = <&aux>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+    __overrides__ {
+      int_pin = <&sc16is752>,"interrupts:0";
+    };
+};

arch/arm/boot/dts/overlays/spi-gpio35-39-overlay.dts

@@ -18,14 +18,14 @@
 	fragment@1 {
 		target = <&spi0_cs_pins>;
 		__overlay__ {
-			bcrm,pins = <36 35>;
+			brcm,pins = <36 35>;
 		};
 	};
 
 	fragment@2 {
 		target = <&spi0_pins>;
 		__overlay__ {
-			bcrm,pins = <37 38 39>;
+			brcm,pins = <37 38 39>;
 		};
 	};
 };

arch/arm/boot/dts/overlays/spi-rtc-overlay.dts

@@ -0,0 +1,33 @@
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&spidev0>;
+		__dormant__ {
+			status = "disabled";
+		};
+	};
+
+	fragment@1 {
+		target = <&spi0>;
+		__dormant__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			rtc-pcf2123@0 {
+				compatible = "nxp,rtc-pcf2123";
+				spi-max-frequency = <5000000>;
+				spi-cs-high = <1>;
+				reg = <0>;
+			};
+		};
+	};
+
+	__overrides__ {
+		pcf2123 = <0>, "=0=1";
+	};
+};

arch/arm/boot/dts/overlays/spi0-hw-cs-overlay.dts

@@ -0,0 +1,26 @@
+/*
+ * Device tree overlay to re-enable hardware CS for SPI0
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2835", "brcm,bcm2836", "brcm,bcm2708", "brcm,bcm2709";
+
+	fragment@0 {
+		target = <&spi0>;
+		__overlay__ {
+			cs-gpios = <0>, <0>;
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&spi0_cs_pins>;
+		__overlay__ {
+			brcm,pins = <8 7>;
+			brcm,function = <4>; /* alt0 */
+		};
+	};
+};

arch/arm/boot/dts/overlays/tinylcd35-overlay.dts

@@ -132,28 +132,32 @@
 
 	fragment@5 {
 		target = <&i2c1>;
-		__overlay__ {
+		__dormant__ {
 			#address-cells = <1>;
 			#size-cells = <0>;
 
+			status = "okay";
+
 			pcf8563: pcf8563@51 {
 				compatible = "nxp,pcf8563";
 				reg = <0x51>;
-				status = "disabled";
+				status = "okay";
 			};
 		};
 	};
 
 	fragment@6 {
 		target = <&i2c1>;
-		__overlay__ {
+		__dormant__ {
 			#address-cells = <1>;
 			#size-cells = <0>;
 
+			status = "okay";
+
 			ds1307: ds1307@68 {
 				compatible = "maxim,ds1307";
 				reg = <0x68>;
-				status = "disabled";
+				status = "okay";
 			};
 		};
 	};
@@ -213,10 +217,8 @@
 			     <&tinylcd35_ts>,"interrupts:0",
 			     <&tinylcd35_ts>,"pendown-gpio:4";
 		xohms =      <&tinylcd35_ts>,"ti,x-plate-ohms;0";
-		rtc-pcf =    <&i2c1>,"status",
-			     <&pcf8563>,"status";
-		rtc-ds =     <&i2c1>,"status",
-			     <&ds1307>,"status";
+		rtc-pcf =    <0>,"=5";
+		rtc-ds =     <0>,"=6";
 		keypad =     <&keypad>,"status";
 	};
 };

arch/arm/boot/dts/overlays/vc4-fkms-v3d-overlay.dts

@@ -0,0 +1,89 @@
+/*
+ * vc4-fkms-v3d-overlay.dts
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
+
+	fragment@0 {
+		target-path = "/chosen";
+		__overlay__ {
+			bootargs = "cma=256M@256M";
+		};
+	};
+
+	fragment@1 {
+		target-path = "/chosen";
+		__dormant__ {
+			bootargs = "cma=192M@256M";
+		};
+	};
+
+	fragment@2 {
+		target-path = "/chosen";
+		__dormant__ {
+			bootargs = "cma=128M@128M";
+		};
+	};
+
+	fragment@3 {
+		target-path = "/chosen";
+		__dormant__ {
+			bootargs = "cma=96M@128M";
+		};
+	};
+
+	fragment@4 {
+		target-path = "/chosen";
+		__dormant__ {
+			bootargs = "cma=64M@64M";
+		};
+	};
+
+	fragment@5 {
+		target = <&fb>;
+		__overlay__  {
+			status = "disabled";
+		};
+	};
+
+	fragment@6 {
+		target = <&firmwarekms>;
+		__overlay__  {
+			status = "okay";
+		};
+	};
+
+	fragment@7 {
+		target = <&v3d>;
+		__overlay__  {
+			interrupts = <1 10>;
+			status = "okay";
+		};
+	};
+
+	fragment@8 {
+		target = <&gpu>;
+		__overlay__  {
+			status = "okay";
+		};
+	};
+
+	fragment@9 {
+		target-path = "/soc/dma";
+		__overlay__ {
+			brcm,dma-channel-mask = <0x7f35>;
+		};
+	};
+
+	__overrides__ {
+		cma-256 = <0>,"+0-1-2-3-4";
+		cma-192 = <0>,"-0+1-2-3-4";
+		cma-128 = <0>,"-0-1+2-3-4";
+		cma-96  = <0>,"-0-1-2+3-4";
+		cma-64  = <0>,"-0-1-2-3+4";
+	};
+};

arch/arm/boot/dts/overlays/vc4-kms-v3d-overlay.dts

@@ -5,129 +5,148 @@
 /dts-v1/;
 /plugin/;
 
-#include "dt-bindings/clock/bcm2835.h"
-#include "dt-bindings/power/raspberrypi-power.h"
-#include "dt-bindings/gpio/gpio.h"
-
 / {
 	compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
 
 	fragment@0 {
-		target = <&i2c2>;
-		__overlay__  {
-			status = "okay";
-		};
-	};
-
-	fragment@1 {
-		target = <&cprman>;
-		__overlay__  {
-			status = "okay";
-		};
-	};
-
-	fragment@2 {
-		target = <&fb>;
-		__overlay__  {
-			status = "disabled";
-		};
-	};
-
-	fragment@3 {
-		target = <&soc>;
-		__overlay__  {
-			#address-cells = <1>;
-			#size-cells = <1>;
-
-			pixelvalve@7e206000 {
-				compatible = "brcm,bcm2835-pixelvalve0";
-				reg = <0x7e206000 0x100>;
-				interrupts = <2 13>; /* pwa0 */
-			};
-
-			pixelvalve@7e207000 {
-				compatible = "brcm,bcm2835-pixelvalve1";
-				reg = <0x7e207000 0x100>;
-				interrupts = <2 14>; /* pwa1 */
-			};
-
-			hvs@7e400000 {
-				compatible = "brcm,bcm2835-hvs";
-				reg = <0x7e400000 0x6000>;
-				interrupts = <2 1>;
-			};
-
-			pixelvalve@7e807000 {
-				compatible = "brcm,bcm2835-pixelvalve2";
-				reg = <0x7e807000 0x100>;
-				interrupts = <2 10>; /* pixelvalve */
-			};
-
-			hdmi@7e902000 {
-				compatible = "brcm,bcm2835-hdmi";
-				reg = <0x7e902000 0x600>,
-				      <0x7e808000 0x100>;
-				interrupts = <2 8>, <2 9>;
-				ddc = <&i2c2>;
-				hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
-				clocks = <&cprman BCM2835_PLLH_PIX>,
-					 <&cprman BCM2835_CLOCK_HSM>;
-				clock-names = "pixel", "hdmi";
-				power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
-			};
-
-			v3d@7ec00000 {
-				compatible = "brcm,vc4-v3d";
-				reg = <0x7ec00000 0x1000>;
-				interrupts = <1 10>;
-			};
-
-			gpu@7e4c0000 {
-				compatible = "brcm,bcm2835-vc4";
-			};
-		};
-	};
-
-	fragment@4 {
 		target-path = "/chosen";
 		__overlay__ {
 			bootargs = "cma=256M@256M";
 		};
 	};
 
-	fragment@5 {
+	fragment@1 {
 		target-path = "/chosen";
 		__dormant__ {
 			bootargs = "cma=192M@256M";
 		};
 	};
 
-	fragment@6 {
+	fragment@2 {
 		target-path = "/chosen";
 		__dormant__ {
 			bootargs = "cma=128M@128M";
 		};
 	};
 
-	fragment@7 {
+	fragment@3 {
 		target-path = "/chosen";
 		__dormant__ {
 			bootargs = "cma=96M@128M";
 		};
 	};
 
-	fragment@8 {
+	fragment@4 {
 		target-path = "/chosen";
 		__dormant__ {
 			bootargs = "cma=64M@64M";
 		};
 	};
 
+	fragment@5 {
+		target = <&i2c2>;
+		__overlay__  {
+			status = "okay";
+		};
+	};
+
+	fragment@6 {
+		target = <&cprman>;
+		__overlay__  {
+			status = "okay";
+		};
+	};
+
+	fragment@7 {
+		target = <&fb>;
+		__overlay__  {
+			status = "disabled";
+		};
+	};
+
+	fragment@8 {
+		target = <&pixelvalve0>;
+		__overlay__  {
+			interrupts = <2 13>; /* pwa0 */
+			status = "okay";
+		};
+	};
+
+	fragment@9 {
+		target = <&pixelvalve1>;
+		__overlay__  {
+			interrupts = <2 14>; /* pwa1 */
+			status = "okay";
+		};
+	};
+
+	fragment@10 {
+		target = <&pixelvalve2>;
+		__overlay__  {
+			interrupts = <2 10>; /* pixelvalve */
+			status = "okay";
+		};
+	};
+
+	fragment@11 {
+		target = <&hvs>;
+		__overlay__  {
+			interrupts = <2 1>;
+			status = "okay";
+		};
+	};
+
+	fragment@12 {
+		target = <&hdmi>;
+		__overlay__  {
+			interrupts = <2 8>, <2 9>;
+			status = "okay";
+		};
+	};
+
+	fragment@13 {
+		target = <&v3d>;
+		__overlay__  {
+			interrupts = <1 10>;
+			status = "okay";
+		};
+	};
+
+	fragment@14 {
+		target = <&gpu>;
+		__overlay__  {
+			status = "okay";
+		};
+	};
+
+	fragment@15 {
+		target-path = "/soc/dma";
+		__overlay__ {
+			brcm,dma-channel-mask = <0x7f35>;
+		};
+	};
+
+	fragment@16 {
+		target = <&dsi1>;
+		__overlay__  {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			brcm,panel = <&pitouchscreen>;
+
+			pitouchscreen: panel {
+				compatible = "raspberrypi,touchscreen";
+				reg = <0>;
+			};
+		};
+	};
+
 	__overrides__ {
-		cma-256 = <0>,"+4-5-6-7-8";
-		cma-192 = <0>,"-4+5-6-7-8";
-		cma-128 = <0>,"-4-5+6-7-8";
-		cma-96  = <0>,"-4-5-6+7-8";
-		cma-64  = <0>,"-4-5-6-7+8";
+		cma-256 = <0>,"+0-1-2-3-4";
+		cma-192 = <0>,"-0+1-2-3-4";
+		cma-128 = <0>,"-0-1+2-3-4";
+		cma-96  = <0>,"-0-1-2+3-4";
+		cma-64  = <0>,"-0-1-2-3+4";
 	};
 };

arch/arm/boot/dts/qcom-apq8064.dtsi

@@ -5,6 +5,7 @@
 #include <dt-bindings/reset/qcom,gcc-msm8960.h>
 #include <dt-bindings/clock/qcom,mmcc-msm8960.h>
 #include <dt-bindings/soc/qcom,gsbi.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 / {
 	model = "Qualcomm APQ8064";
@@ -354,22 +355,50 @@
 
 					compatible = "qcom,pm8921-gpio";
 					reg = <0x150>;
-					interrupts = <192 1>, <193 1>, <194 1>,
-						     <195 1>, <196 1>, <197 1>,
-						     <198 1>, <199 1>, <200 1>,
-						     <201 1>, <202 1>, <203 1>,
-						     <204 1>, <205 1>, <206 1>,
-						     <207 1>, <208 1>, <209 1>,
-						     <210 1>, <211 1>, <212 1>,
-						     <213 1>, <214 1>, <215 1>,
-						     <216 1>, <217 1>, <218 1>,
-						     <219 1>, <220 1>, <221 1>,
-						     <222 1>, <223 1>, <224 1>,
-						     <225 1>, <226 1>, <227 1>,
-						     <228 1>, <229 1>, <230 1>,
-						     <231 1>, <232 1>, <233 1>,
-						     <234 1>, <235 1>;
-
+					interrupts = <192 IRQ_TYPE_NONE>,
+						     <193 IRQ_TYPE_NONE>,
+						     <194 IRQ_TYPE_NONE>,
+						     <195 IRQ_TYPE_NONE>,
+						     <196 IRQ_TYPE_NONE>,
+						     <197 IRQ_TYPE_NONE>,
+						     <198 IRQ_TYPE_NONE>,
+						     <199 IRQ_TYPE_NONE>,
+						     <200 IRQ_TYPE_NONE>,
+						     <201 IRQ_TYPE_NONE>,
+						     <202 IRQ_TYPE_NONE>,
+						     <203 IRQ_TYPE_NONE>,
+						     <204 IRQ_TYPE_NONE>,
+						     <205 IRQ_TYPE_NONE>,
+						     <206 IRQ_TYPE_NONE>,
+						     <207 IRQ_TYPE_NONE>,
+						     <208 IRQ_TYPE_NONE>,
+						     <209 IRQ_TYPE_NONE>,
+						     <210 IRQ_TYPE_NONE>,
+						     <211 IRQ_TYPE_NONE>,
+						     <212 IRQ_TYPE_NONE>,
+						     <213 IRQ_TYPE_NONE>,
+						     <214 IRQ_TYPE_NONE>,
+						     <215 IRQ_TYPE_NONE>,
+						     <216 IRQ_TYPE_NONE>,
+						     <217 IRQ_TYPE_NONE>,
+						     <218 IRQ_TYPE_NONE>,
+						     <219 IRQ_TYPE_NONE>,
+						     <220 IRQ_TYPE_NONE>,
+						     <221 IRQ_TYPE_NONE>,
+						     <222 IRQ_TYPE_NONE>,
+						     <223 IRQ_TYPE_NONE>,
+						     <224 IRQ_TYPE_NONE>,
+						     <225 IRQ_TYPE_NONE>,
+						     <226 IRQ_TYPE_NONE>,
+						     <227 IRQ_TYPE_NONE>,
+						     <228 IRQ_TYPE_NONE>,
+						     <229 IRQ_TYPE_NONE>,
+						     <230 IRQ_TYPE_NONE>,
+						     <231 IRQ_TYPE_NONE>,
+						     <232 IRQ_TYPE_NONE>,
+						     <233 IRQ_TYPE_NONE>,
+						     <234 IRQ_TYPE_NONE>,
+						     <235 IRQ_TYPE_NONE>;
 					gpio-controller;
 					#gpio-cells = <2>;
 
@@ -381,9 +410,18 @@
 					gpio-controller;
 					#gpio-cells = <2>;
 					interrupts =
-					<128 1>, <129 1>, <130 1>, <131 1>,
-					<132 1>, <133 1>, <134 1>, <135 1>,
-					<136 1>, <137 1>, <138 1>, <139 1>;
+					<128 IRQ_TYPE_NONE>,
+					<129 IRQ_TYPE_NONE>,
+					<130 IRQ_TYPE_NONE>,
+					<131 IRQ_TYPE_NONE>,
+					<132 IRQ_TYPE_NONE>,
+					<133 IRQ_TYPE_NONE>,
+					<134 IRQ_TYPE_NONE>,
+					<135 IRQ_TYPE_NONE>,
+					<136 IRQ_TYPE_NONE>,
+					<137 IRQ_TYPE_NONE>,
+					<138 IRQ_TYPE_NONE>,
+					<139 IRQ_TYPE_NONE>;
 				};
 
 				rtc@11d {

arch/arm/boot/dts/sama5d2-pinfunc.h

@@ -837,8 +837,8 @@
 #define PIN_PD23__ISC_FIELD		PINMUX_PIN(PIN_PD23, 6, 4)
 #define PIN_PD24			120
 #define PIN_PD24__GPIO			PINMUX_PIN(PIN_PD24, 0, 0)
-#define PIN_PD24__UTXD2			PINMUX_PIN(PIN_PD23, 1, 2)
-#define PIN_PD24__FLEXCOM4_IO3		PINMUX_PIN(PIN_PD23, 3, 3)
+#define PIN_PD24__UTXD2			PINMUX_PIN(PIN_PD24, 1, 2)
+#define PIN_PD24__FLEXCOM4_IO3		PINMUX_PIN(PIN_PD24, 3, 3)
 #define PIN_PD25			121
 #define PIN_PD25__GPIO			PINMUX_PIN(PIN_PD25, 0, 0)
 #define PIN_PD25__SPI1_SPCK		PINMUX_PIN(PIN_PD25, 1, 3)

arch/arm/boot/dts/stih407-family.dtsi

@@ -497,8 +497,9 @@
 			interrupt-names = "mmcirq";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_mmc0>;
-			clock-names = "mmc";
-			clocks = <&clk_s_c0_flexgen CLK_MMC_0>;
+			clock-names = "mmc", "icn";
+			clocks = <&clk_s_c0_flexgen CLK_MMC_0>,
+				 <&clk_s_c0_flexgen CLK_RX_ICN_HVA>;
 			bus-width = <8>;
 			non-removable;
 		};
@@ -512,8 +513,9 @@
 			interrupt-names = "mmcirq";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_sd1>;
-			clock-names = "mmc";
-			clocks = <&clk_s_c0_flexgen CLK_MMC_1>;
+			clock-names = "mmc", "icn";
+			clocks = <&clk_s_c0_flexgen CLK_MMC_1>,
+				 <&clk_s_c0_flexgen CLK_RX_ICN_HVA>;
 			resets = <&softreset STIH407_MMC1_SOFTRESET>;
 			bus-width = <4>;
 		};

arch/arm/boot/dts/stih410.dtsi

@@ -41,7 +41,8 @@
 			compatible = "st,st-ohci-300x";
 			reg = <0x9a03c00 0x100>;
 			interrupts = <GIC_SPI 180 IRQ_TYPE_NONE>;
-			clocks = <&clk_s_c0_flexgen CLK_TX_ICN_DISP_0>;
+			clocks = <&clk_s_c0_flexgen CLK_TX_ICN_DISP_0>,
+				 <&clk_s_c0_flexgen CLK_RX_ICN_DISP_0>;
 			resets = <&powerdown STIH407_USB2_PORT0_POWERDOWN>,
 				 <&softreset STIH407_USB2_PORT0_SOFTRESET>;
 			reset-names = "power", "softreset";
@@ -57,7 +58,8 @@
 			interrupts = <GIC_SPI 151 IRQ_TYPE_NONE>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb0>;
-			clocks = <&clk_s_c0_flexgen CLK_TX_ICN_DISP_0>;
+			clocks = <&clk_s_c0_flexgen CLK_TX_ICN_DISP_0>,
+				 <&clk_s_c0_flexgen CLK_RX_ICN_DISP_0>;
 			resets = <&powerdown STIH407_USB2_PORT0_POWERDOWN>,
 				 <&softreset STIH407_USB2_PORT0_SOFTRESET>;
 			reset-names = "power", "softreset";
@@ -71,7 +73,8 @@
 			compatible = "st,st-ohci-300x";
 			reg = <0x9a83c00 0x100>;
 			interrupts = <GIC_SPI 181 IRQ_TYPE_NONE>;
-			clocks = <&clk_s_c0_flexgen CLK_TX_ICN_DISP_0>;
+			clocks = <&clk_s_c0_flexgen CLK_TX_ICN_DISP_0>,
+				 <&clk_s_c0_flexgen CLK_RX_ICN_DISP_0>;
 			resets = <&powerdown STIH407_USB2_PORT1_POWERDOWN>,
 				 <&softreset STIH407_USB2_PORT1_SOFTRESET>;
 			reset-names = "power", "softreset";
@@ -87,7 +90,8 @@
 			interrupts = <GIC_SPI 153 IRQ_TYPE_NONE>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb1>;
-			clocks = <&clk_s_c0_flexgen CLK_TX_ICN_DISP_0>;
+			clocks = <&clk_s_c0_flexgen CLK_TX_ICN_DISP_0>,
+				 <&clk_s_c0_flexgen CLK_RX_ICN_DISP_0>;
 			resets = <&powerdown STIH407_USB2_PORT1_POWERDOWN>,
 				 <&softreset STIH407_USB2_PORT1_SOFTRESET>;
 			reset-names = "power", "softreset";

arch/arm/boot/dts/sun4i-a10-a1000.dts

@@ -84,6 +84,7 @@
 		regulator-name = "emac-3v3";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <20000>;
 		enable-active-high;
 		gpio = <&pio 7 15 GPIO_ACTIVE_HIGH>;
 	};

arch/arm/boot/dts/sun4i-a10-hackberry.dts

@@ -66,6 +66,7 @@
 		regulator-name = "emac-3v3";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <20000>;
 		enable-active-high;
 		gpio = <&pio 7 19 GPIO_ACTIVE_HIGH>;
 	};

arch/arm/boot/dts/sun4i-a10-jesurun-q5.dts

@@ -80,6 +80,7 @@
 		regulator-name = "emac-3v3";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <20000>;
 		enable-active-high;
 		gpio = <&pio 7 19 GPIO_ACTIVE_HIGH>;   /* PH19 */
 	};

arch/arm/boot/dts/sun5i-a10s-wobo-i5.dts

@@ -79,6 +79,7 @@
 		regulator-name = "emac-3v3";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <20000>;
 		enable-active-high;
 		gpio = <&pio 0 2 GPIO_ACTIVE_HIGH>;
 	};

arch/arm/boot/dts/sun5i-a13.dtsi

@@ -83,7 +83,7 @@
 			trips {
 				cpu_alert0: cpu_alert0 {
 					/* milliCelsius */
-					temperature = <850000>;
+					temperature = <85000>;
 					hysteresis = <2000>;
 					type = "passive";
 				};

arch/arm/boot/dts/sun5i-r8-chip.dts

@@ -52,7 +52,7 @@
 
 / {
 	model = "NextThing C.H.I.P.";
-	compatible = "nextthing,chip", "allwinner,sun5i-r8";
+	compatible = "nextthing,chip", "allwinner,sun5i-r8", "allwinner,sun5i-a13";
 
 	aliases {
 		i2c0 = &i2c0;

arch/arm/common/sa1111.c

@@ -869,9 +869,9 @@ struct sa1111_save_data {
 
 #ifdef CONFIG_PM
 
-static int sa1111_suspend(struct platform_device *dev, pm_message_t state)
+static int sa1111_suspend_noirq(struct device *dev)
 {
-	struct sa1111 *sachip = platform_get_drvdata(dev);
+	struct sa1111 *sachip = dev_get_drvdata(dev);
 	struct sa1111_save_data *save;
 	unsigned long flags;
 	unsigned int val;
@@ -934,9 +934,9 @@ static int sa1111_suspend(struct platform_device *dev, pm_message_t state)
  *	restored by their respective drivers, and must be called
  *	via LDM after this function.
  */
-static int sa1111_resume(struct platform_device *dev)
+static int sa1111_resume_noirq(struct device *dev)
 {
-	struct sa1111 *sachip = platform_get_drvdata(dev);
+	struct sa1111 *sachip = dev_get_drvdata(dev);
 	struct sa1111_save_data *save;
 	unsigned long flags, id;
 	void __iomem *base;
@@ -952,7 +952,7 @@ static int sa1111_resume(struct platform_device *dev)
 	id = sa1111_readl(sachip->base + SA1111_SKID);
 	if ((id & SKID_ID_MASK) != SKID_SA1111_ID) {
 		__sa1111_remove(sachip);
-		platform_set_drvdata(dev, NULL);
+		dev_set_drvdata(dev, NULL);
 		kfree(save);
 		return 0;
 	}
@@ -1003,8 +1003,8 @@ static int sa1111_resume(struct platform_device *dev)
 }
 
 #else
-#define sa1111_suspend NULL
-#define sa1111_resume  NULL
+#define sa1111_suspend_noirq NULL
+#define sa1111_resume_noirq  NULL
 #endif
 
 static int sa1111_probe(struct platform_device *pdev)
@@ -1038,6 +1038,11 @@ static int sa1111_remove(struct platform_device *pdev)
 	return 0;
 }
 
+static struct dev_pm_ops sa1111_pm_ops = {
+	.suspend_noirq = sa1111_suspend_noirq,
+	.resume_noirq = sa1111_resume_noirq,
+};
+
 /*
  *	Not sure if this should be on the system bus or not yet.
  *	We really want some way to register a system device at
@@ -1050,10 +1055,9 @@ static int sa1111_remove(struct platform_device *pdev)
 static struct platform_driver sa1111_device_driver = {
 	.probe		= sa1111_probe,
 	.remove		= sa1111_remove,
-	.suspend	= sa1111_suspend,
-	.resume		= sa1111_resume,
 	.driver		= {
 		.name	= "sa1111",
+		.pm	= &sa1111_pm_ops,
 	},
 };
 

arch/arm/configs/bcm2709_defconfig

@@ -223,6 +223,7 @@ CONFIG_NF_CONNTRACK_IPV4=m
 CONFIG_IP_NF_IPTABLES=m
 CONFIG_IP_NF_MATCH_AH=m
 CONFIG_IP_NF_MATCH_ECN=m
+CONFIG_IP_NF_MATCH_RPFILTER=m
 CONFIG_IP_NF_MATCH_TTL=m
 CONFIG_IP_NF_FILTER=m
 CONFIG_IP_NF_TARGET_REJECT=m
@@ -247,6 +248,7 @@ CONFIG_IP6_NF_MATCH_OPTS=m
 CONFIG_IP6_NF_MATCH_HL=m
 CONFIG_IP6_NF_MATCH_IPV6HEADER=m
 CONFIG_IP6_NF_MATCH_MH=m
+CONFIG_IP6_NF_MATCH_RPFILTER=m
 CONFIG_IP6_NF_MATCH_RT=m
 CONFIG_IP6_NF_TARGET_HL=m
 CONFIG_IP6_NF_FILTER=m
@@ -446,6 +448,8 @@ CONFIG_BONDING=m
 CONFIG_DUMMY=m
 CONFIG_IFB=m
 CONFIG_MACVLAN=m
+CONFIG_IPVLAN=m
+CONFIG_VXLAN=m
 CONFIG_NETCONSOLE=m
 CONFIG_TUN=m
 CONFIG_VETH=m
@@ -557,6 +561,7 @@ CONFIG_JOYSTICK_IFORCE=m
 CONFIG_JOYSTICK_IFORCE_USB=y
 CONFIG_JOYSTICK_XPAD=m
 CONFIG_JOYSTICK_XPAD_FF=y
+CONFIG_JOYSTICK_XPAD_LEDS=y
 CONFIG_JOYSTICK_RPISENSE=m
 CONFIG_INPUT_TOUCHSCREEN=y
 CONFIG_TOUCHSCREEN_ADS7846=m
@@ -597,6 +602,8 @@ CONFIG_SERIAL_8250_RUNTIME_UARTS=0
 CONFIG_SERIAL_AMBA_PL011=y
 CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
 CONFIG_SERIAL_OF_PLATFORM=y
+CONFIG_SERIAL_SC16IS7XX=m
+CONFIG_SERIAL_SC16IS7XX_SPI=y
 CONFIG_TTY_PRINTK=y
 CONFIG_HW_RANDOM=y
 CONFIG_RAW_DRIVER=y
@@ -616,6 +623,7 @@ CONFIG_GPIO_SYSFS=y
 CONFIG_GPIO_BCM_VIRT=y
 CONFIG_GPIO_ARIZONA=m
 CONFIG_GPIO_STMPE=y
+CONFIG_GPIO_MCP23S08=m
 CONFIG_W1=m
 CONFIG_W1_MASTER_DS2490=m
 CONFIG_W1_MASTER_DS2482=m
@@ -638,8 +646,10 @@ CONFIG_BATTERY_DS2760=m
 CONFIG_POWER_RESET=y
 CONFIG_POWER_RESET_GPIO=y
 CONFIG_HWMON=m
+CONFIG_SENSORS_LM75=m
 CONFIG_SENSORS_SHT21=m
 CONFIG_SENSORS_SHTC1=m
+CONFIG_SENSORS_INA2XX=m
 CONFIG_THERMAL=y
 CONFIG_THERMAL_BCM2835=y
 CONFIG_WATCHDOG=y
@@ -815,7 +825,10 @@ CONFIG_VIDEO_TW9906=m
 CONFIG_VIDEO_OV7640=m
 CONFIG_VIDEO_MT9V011=m
 CONFIG_DRM=m
+CONFIG_DRM_LOAD_EDID_FIRMWARE=y
 CONFIG_DRM_UDL=m
+CONFIG_DRM_PANEL_SIMPLE=m
+CONFIG_DRM_PANEL_RASPBERRYPI_TOUCHSCREEN=m
 CONFIG_DRM_VC4=m
 CONFIG_FB=y
 CONFIG_FB_BCM2708=y
@@ -857,10 +870,16 @@ CONFIG_SND_BCM2708_SOC_HIFIBERRY_DIGI=m
 CONFIG_SND_BCM2708_SOC_HIFIBERRY_AMP=m
 CONFIG_SND_BCM2708_SOC_RPI_DAC=m
 CONFIG_SND_BCM2708_SOC_RPI_PROTO=m
-CONFIG_SND_BCM2708_SOC_BOOMBERRY_DAC=m
-CONFIG_SND_BCM2708_SOC_BOOMBERRY_DIGI=m
+CONFIG_SND_BCM2708_SOC_JUSTBOOM_DAC=m
+CONFIG_SND_BCM2708_SOC_JUSTBOOM_DIGI=m
 CONFIG_SND_BCM2708_SOC_IQAUDIO_DAC=m
+CONFIG_SND_BCM2708_SOC_IQAUDIO_DIGI=m
 CONFIG_SND_BCM2708_SOC_RASPIDAC3=m
+CONFIG_SND_BCM2708_SOC_ADAU1977_ADC=m
+CONFIG_SND_AUDIOINJECTOR_PI_SOUNDCARD=m
+CONFIG_SND_DIGIDAC1_SOUNDCARD=m
+CONFIG_SND_BCM2708_SOC_DIONAUDIO_LOCO=m
+CONFIG_SND_BCM2708_SOC_ALLO_PIANO_DAC=m
 CONFIG_SND_SOC_ADAU1701=m
 CONFIG_SND_SOC_WM8804_I2C=m
 CONFIG_SND_SIMPLE_CARD=m
@@ -880,6 +899,7 @@ CONFIG_HID_EMS_FF=m
 CONFIG_HID_ELECOM=m
 CONFIG_HID_ELO=m
 CONFIG_HID_EZKEY=m
+CONFIG_HID_GEMBIRD=m
 CONFIG_HID_HOLTEK=m
 CONFIG_HID_KEYTOUCH=m
 CONFIG_HID_KYE=m
@@ -890,6 +910,10 @@ CONFIG_HID_TWINHAN=m
 CONFIG_HID_KENSINGTON=m
 CONFIG_HID_LCPOWER=m
 CONFIG_HID_LOGITECH=m
+CONFIG_HID_LOGITECH_DJ=m
+CONFIG_LOGITECH_FF=y
+CONFIG_LOGIRUMBLEPAD2_FF=y
+CONFIG_LOGIG940_FF=y
 CONFIG_HID_MAGICMOUSE=m
 CONFIG_HID_MICROSOFT=m
 CONFIG_HID_MONTEREY=m
@@ -1092,6 +1116,7 @@ CONFIG_FB_TFT_BD663474=m
 CONFIG_FB_TFT_HX8340BN=m
 CONFIG_FB_TFT_HX8347D=m
 CONFIG_FB_TFT_HX8353D=m
+CONFIG_FB_TFT_HX8357D=m
 CONFIG_FB_TFT_ILI9163=m
 CONFIG_FB_TFT_ILI9320=m
 CONFIG_FB_TFT_ILI9325=m

arch/arm/configs/bcmrpi_defconfig

@@ -216,6 +216,7 @@ CONFIG_NF_CONNTRACK_IPV4=m
 CONFIG_IP_NF_IPTABLES=m
 CONFIG_IP_NF_MATCH_AH=m
 CONFIG_IP_NF_MATCH_ECN=m
+CONFIG_IP_NF_MATCH_RPFILTER=m
 CONFIG_IP_NF_MATCH_TTL=m
 CONFIG_IP_NF_FILTER=m
 CONFIG_IP_NF_TARGET_REJECT=m
@@ -240,6 +241,7 @@ CONFIG_IP6_NF_MATCH_OPTS=m
 CONFIG_IP6_NF_MATCH_HL=m
 CONFIG_IP6_NF_MATCH_IPV6HEADER=m
 CONFIG_IP6_NF_MATCH_MH=m
+CONFIG_IP6_NF_MATCH_RPFILTER=m
 CONFIG_IP6_NF_MATCH_RT=m
 CONFIG_IP6_NF_TARGET_HL=m
 CONFIG_IP6_NF_FILTER=m
@@ -439,6 +441,8 @@ CONFIG_BONDING=m
 CONFIG_DUMMY=m
 CONFIG_IFB=m
 CONFIG_MACVLAN=m
+CONFIG_IPVLAN=m
+CONFIG_VXLAN=m
 CONFIG_NETCONSOLE=m
 CONFIG_TUN=m
 CONFIG_VETH=m
@@ -550,6 +554,7 @@ CONFIG_JOYSTICK_IFORCE=m
 CONFIG_JOYSTICK_IFORCE_USB=y
 CONFIG_JOYSTICK_XPAD=m
 CONFIG_JOYSTICK_XPAD_FF=y
+CONFIG_JOYSTICK_XPAD_LEDS=y
 CONFIG_JOYSTICK_RPISENSE=m
 CONFIG_INPUT_TOUCHSCREEN=y
 CONFIG_TOUCHSCREEN_ADS7846=m
@@ -590,6 +595,8 @@ CONFIG_SERIAL_8250_RUNTIME_UARTS=0
 CONFIG_SERIAL_AMBA_PL011=y
 CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
 CONFIG_SERIAL_OF_PLATFORM=y
+CONFIG_SERIAL_SC16IS7XX=m
+CONFIG_SERIAL_SC16IS7XX_SPI=y
 CONFIG_TTY_PRINTK=y
 CONFIG_HW_RANDOM=y
 CONFIG_RAW_DRIVER=y
@@ -608,6 +615,7 @@ CONFIG_PPS_CLIENT_GPIO=m
 CONFIG_GPIO_SYSFS=y
 CONFIG_GPIO_ARIZONA=m
 CONFIG_GPIO_STMPE=y
+CONFIG_GPIO_MCP23S08=m
 CONFIG_W1=m
 CONFIG_W1_MASTER_DS2490=m
 CONFIG_W1_MASTER_DS2482=m
@@ -630,8 +638,10 @@ CONFIG_BATTERY_DS2760=m
 CONFIG_POWER_RESET=y
 CONFIG_POWER_RESET_GPIO=y
 CONFIG_HWMON=m
+CONFIG_SENSORS_LM75=m
 CONFIG_SENSORS_SHT21=m
 CONFIG_SENSORS_SHTC1=m
+CONFIG_SENSORS_INA2XX=m
 CONFIG_THERMAL=y
 CONFIG_THERMAL_BCM2835=y
 CONFIG_WATCHDOG=y
@@ -807,7 +817,10 @@ CONFIG_VIDEO_TW9906=m
 CONFIG_VIDEO_OV7640=m
 CONFIG_VIDEO_MT9V011=m
 CONFIG_DRM=m
+CONFIG_DRM_LOAD_EDID_FIRMWARE=y
 CONFIG_DRM_UDL=m
+CONFIG_DRM_PANEL_SIMPLE=m
+CONFIG_DRM_PANEL_RASPBERRYPI_TOUCHSCREEN=m
 CONFIG_DRM_VC4=m
 CONFIG_FB=y
 CONFIG_FB_BCM2708=y
@@ -849,10 +862,16 @@ CONFIG_SND_BCM2708_SOC_HIFIBERRY_DIGI=m
 CONFIG_SND_BCM2708_SOC_HIFIBERRY_AMP=m
 CONFIG_SND_BCM2708_SOC_RPI_DAC=m
 CONFIG_SND_BCM2708_SOC_RPI_PROTO=m
-CONFIG_SND_BCM2708_SOC_BOOMBERRY_DAC=m
-CONFIG_SND_BCM2708_SOC_BOOMBERRY_DIGI=m
+CONFIG_SND_BCM2708_SOC_JUSTBOOM_DAC=m
+CONFIG_SND_BCM2708_SOC_JUSTBOOM_DIGI=m
 CONFIG_SND_BCM2708_SOC_IQAUDIO_DAC=m
+CONFIG_SND_BCM2708_SOC_IQAUDIO_DIGI=m
 CONFIG_SND_BCM2708_SOC_RASPIDAC3=m
+CONFIG_SND_BCM2708_SOC_ADAU1977_ADC=m
+CONFIG_SND_AUDIOINJECTOR_PI_SOUNDCARD=m
+CONFIG_SND_DIGIDAC1_SOUNDCARD=m
+CONFIG_SND_BCM2708_SOC_DIONAUDIO_LOCO=m
+CONFIG_SND_BCM2708_SOC_ALLO_PIANO_DAC=m
 CONFIG_SND_SOC_ADAU1701=m
 CONFIG_SND_SOC_WM8804_I2C=m
 CONFIG_SND_SIMPLE_CARD=m
@@ -872,6 +891,7 @@ CONFIG_HID_EMS_FF=m
 CONFIG_HID_ELECOM=m
 CONFIG_HID_ELO=m
 CONFIG_HID_EZKEY=m
+CONFIG_HID_GEMBIRD=m
 CONFIG_HID_HOLTEK=m
 CONFIG_HID_KEYTOUCH=m
 CONFIG_HID_KYE=m
@@ -882,6 +902,10 @@ CONFIG_HID_TWINHAN=m
 CONFIG_HID_KENSINGTON=m
 CONFIG_HID_LCPOWER=m
 CONFIG_HID_LOGITECH=m
+CONFIG_HID_LOGITECH_DJ=m
+CONFIG_LOGITECH_FF=y
+CONFIG_LOGIRUMBLEPAD2_FF=y
+CONFIG_LOGIG940_FF=y
 CONFIG_HID_MAGICMOUSE=m
 CONFIG_HID_MICROSOFT=m
 CONFIG_HID_MONTEREY=m
@@ -1099,6 +1123,7 @@ CONFIG_FB_TFT_BD663474=m
 CONFIG_FB_TFT_HX8340BN=m
 CONFIG_FB_TFT_HX8347D=m
 CONFIG_FB_TFT_HX8353D=m
+CONFIG_FB_TFT_HX8357D=m
 CONFIG_FB_TFT_ILI9163=m
 CONFIG_FB_TFT_ILI9320=m
 CONFIG_FB_TFT_ILI9325=m