Pi3 DT: Add dtparams for the SD interface

Add new base dtparams sd_overclock, sd_force_pio, sd_pio_limit
and sd_debug. These were missed out of the initial Pi3 DTB.

Signed-off-by: Phil Elwell <phil@raspberrypi.org>

Documentation/devicetree/bindings/clock/brcm,bcm2835-cprman.txt

@@ -0,0 +1,45 @@
+Broadcom BCM2835 CPRMAN clocks
+
+This binding uses the common clock binding:
+    Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+The CPRMAN clock controller generates clocks in the audio power domain
+of the BCM2835.  There is a level of PLLs deriving from an external
+oscillator, a level of PLL dividers that produce channels off of the
+few PLLs, and a level of mostly-generic clock generators sourcing from
+the PLL channels.  Most other hardware components source from the
+clock generators, but a few (like the ARM or HDMI) will source from
+the PLL dividers directly.
+
+Required properties:
+- compatible:	Should be "brcm,bcm2835-cprman"
+- #clock-cells:	Should be <1>. The permitted clock-specifier values can be
+		  found in include/dt-bindings/clock/bcm2835.h
+- reg:		Specifies base physical address and size of the registers
+- clocks:	The external oscillator clock phandle
+
+Example:
+
+	clk_osc: clock@3 {
+		compatible = "fixed-clock";
+		reg = <3>;
+		#clock-cells = <0>;
+		clock-output-names = "osc";
+		clock-frequency = <19200000>;
+	};
+
+	clocks: cprman@7e101000 {
+		compatible = "brcm,bcm2835-cprman";
+		#clock-cells = <1>;
+		reg = <0x7e101000 0x2000>;
+		clocks = <&clk_osc>;
+	};
+
+	i2c0: i2c@7e205000 {
+		compatible = "brcm,bcm2835-i2c";
+		reg = <0x7e205000 0x1000>;
+		interrupts = <2 21>;
+		clocks = <&clocks BCM2835_CLOCK_VPU>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};

Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt

@@ -0,0 +1,65 @@
+Broadcom VC4 (VideoCore4) GPU
+
+The VC4 device present on the Raspberry Pi includes a display system
+with HDMI output and the HVS (Hardware Video Scaler) for compositing
+display planes.
+
+Required properties for VC4:
+- compatible:	Should be "brcm,bcm2835-vc4"
+
+Required properties for Pixel Valve:
+- compatible:	Should be one of "brcm,bcm2835-pixelvalve0",
+		  "brcm,bcm2835-pixelvalve1", or "brcm,bcm2835-pixelvalve2"
+- reg:		Physical base address and length of the PV's registers
+- interrupts:	The interrupt number
+		  See bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt
+
+Required properties for HVS:
+- compatible:	Should be "brcm,bcm2835-hvs"
+- reg:		Physical base address and length of the HVS's registers
+- interrupts:	The interrupt number
+		  See bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt
+
+Required properties for HDMI
+- compatible:	Should be "brcm,bcm2835-hdmi"
+- reg:		Physical base address and length of the two register ranges
+		  ("HDMI" and "HD", in that order)
+- interrupts:	The interrupt numbers
+		  See bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt
+- ddc:		phandle of the I2C controller used for DDC EDID probing
+- clocks:	a) hdmi: The HDMI state machine clock
+		b) pixel: The pixel clock.
+
+Optional properties for HDMI:
+- hpd-gpio:	The GPIO pin for HDMI hotplug detect (if it doesn't appear
+		  as an interrupt/status bit in the HDMI controller
+		  itself).  See bindings/pinctrl/brcm,bcm2835-gpio.txt
+
+Example:
+pixelvalve@7e807000 {
+	compatible = "brcm,bcm2835-pixelvalve2";
+	reg = <0x7e807000 0x100>;
+	interrupts = <2 10>; /* pixelvalve */
+};
+
+hvs@7e400000 {
+	compatible = "brcm,bcm2835-hvs";
+	reg = <0x7e400000 0x6000>;
+	interrupts = <2 1>;
+};
+
+hdmi: hdmi@7e902000 {
+	compatible = "brcm,bcm2835-hdmi";
+	reg = <0x7e902000 0x600>,
+	      <0x7e808000 0x100>;
+	interrupts = <2 8>, <2 9>;
+	ddc = <&i2c2>;
+	hpd-gpio = <&gpio 46 GPIO_ACTIVE_HIGH>;
+	clocks = <&clocks BCM2835_PLLH_PIX>,
+		 <&clocks BCM2835_CLOCK_HSM>;
+	clock-names = "pixel", "hdmi";
+};
+
+vc4: gpu@7e4c0000 {
+	compatible = "brcm,bcm2835-vc4";
+};

Documentation/devicetree/bindings/dma/brcm,bcm2835-dma.txt

@@ -48,8 +48,8 @@ Example:
 
 bcm2835_i2s: i2s@7e203000 {
 	compatible = "brcm,bcm2835-i2s";
-	reg = <	0x7e203000 0x20>,
+	reg = <	0x7e203000 0x24>,
-	      < 0x7e101098 0x02>;
+	      < 0x7e101098 0x08>;
 
 	dmas = <&dma 2>,
 	       <&dma 3>;

Documentation/devicetree/bindings/input/touchscreen/focaltech-ft6236.txt

@@ -0,0 +1,35 @@
+* FocalTech FT6236 I2C touchscreen controller
+
+Required properties:
+ - compatible		  : "focaltech,ft6236"
+ - reg			  : I2C slave address of the chip (0x38)
+ - interrupt-parent	  : a phandle pointing to the interrupt controller
+			    serving the interrupt for this chip
+ - interrupts		  : interrupt specification for the touch controller
+			    interrupt
+ - reset-gpios		  : GPIO specification for the RSTN input
+ - touchscreen-size-x	  : horizontal resolution of touchscreen (in pixels)
+ - touchscreen-size-y	  : vertical resolution of touchscreen (in pixels)
+
+Optional properties:
+ - touchscreen-fuzz-x	  : horizontal noise value of the absolute input
+			    device (in pixels)
+ - touchscreen-fuzz-y	  : vertical noise value of the absolute input
+			    device (in pixels)
+ - touchscreen-inverted-x : X axis is inverted (boolean)
+ - touchscreen-inverted-y : Y axis is inverted (boolean)
+ - touchscreen-swapped-x-y: X and Y axis are swapped (boolean)
+			    Swapping is done after inverting the axis
+
+Example:
+
+	ft6x06@38 {
+		compatible = "focaltech,ft6236";
+		reg = <0x38>;
+		interrupt-parent = <&gpio>;
+		interrupts = <23 2>;
+		touchscreen-size-x = <320>;
+		touchscreen-size-y = <480>;
+		touchscreen-inverted-x;
+		touchscreen-swapped-x-y;
+	};

Documentation/devicetree/bindings/misc/brcm,bcm2835-smi-dev.txt

@@ -0,0 +1,17 @@
+* Broadcom BCM2835 SMI character device driver.
+
+SMI or secondary memory interface is a peripheral specific to certain Broadcom
+SOCs, and is helpful for talking to things like parallel-interface displays
+and NAND flashes (in fact, most things with a parallel register interface).
+
+This driver adds a character device which provides a user-space interface to
+an instance of the SMI driver.
+
+Required properties:
+- compatible: "brcm,bcm2835-smi-dev"
+- smi_handle: a phandle to the smi node.
+
+Optional properties:
+- None.
+
+

Documentation/devicetree/bindings/misc/brcm,bcm2835-smi.txt

@@ -0,0 +1,48 @@
+* Broadcom BCM2835 SMI driver.
+
+SMI or secondary memory interface is a peripheral specific to certain Broadcom
+SOCs, and is helpful for talking to things like parallel-interface displays
+and NAND flashes (in fact, most things with a parallel register interface).
+
+Required properties:
+- compatible: "brcm,bcm2835-smi"
+- reg: Should contain location and length of SMI registers and SMI clkman regs
+- interrupts: *the* SMI interrupt.
+- pinctrl-names: should be "default".
+- pinctrl-0: the phandle of the gpio pin node.
+- brcm,smi-clock-source: the clock source for clkman
+- brcm,smi-clock-divisor: the integer clock divisor for clkman
+- dmas: the dma controller phandle and the DREQ number (4 on a 2835)
+- dma-names: the name used by the driver to request its channel.
+  Should be "rx-tx".
+
+Optional properties:
+- None.
+
+Examples:
+
+8 data pin configuration:
+
+smi: smi@7e600000 {
+	compatible = "brcm,bcm2835-smi";
+	reg = <0x7e600000 0x44>, <0x7e1010b0 0x8>;
+	interrupts = <2 16>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&smi_pins>;
+	brcm,smi-clock-source = <6>;
+	brcm,smi-clock-divisor = <4>;
+	dmas = <&dma 4>;
+	dma-names = "rx-tx";
+
+	status = "okay";
+};
+
+smi_pins: smi_pins {
+	brcm,pins = <2 3 4 5 6 7 8 9 10 11 12 13 14 15>;
+	/* Alt 1: SMI */
+	brcm,function = <5 5 5 5 5 5 5 5 5 5 5 5 5 5>;
+	/* /CS, /WE and /OE are pulled high, as they are
+	   generally active low signals */
+	brcm,pull = <2 2 2 2 2 2 0 0 0 0 0 0 0 0>;
+};
+

Documentation/devicetree/bindings/mtd/brcm,bcm2835-smi-nand.txt

@@ -0,0 +1,42 @@
+* BCM2835 SMI NAND flash
+
+This driver is a shim between the BCM2835 SMI driver (SMI is a peripheral for
+talking to parallel register interfaces) and Linux's MTD layer.
+
+Required properties:
+- compatible: "brcm,bcm2835-smi-nand"
+- status: "okay"
+
+Optional properties:
+- partition@n, where n is an integer from a consecutive sequence starting at 0
+	- Difficult to store partition table on NAND device - normally put it
+	in the source code, kernel bootparams, or device tree (the best way!)
+	- Sub-properties:
+		- label: the partition name, as shown by mtdinfo /dev/mtd*
+		- reg: the size and offset of this partition.
+		- (optional) read-only: an empty property flagging as read only
+
+Example:
+
+nand: flash@0 {
+	compatible = "brcm,bcm2835-smi-nand";
+	status = "okay";
+
+	partition@0 {
+		label = "stage2";
+		// 128k
+		reg = <0 0x20000>;
+		read-only;
+	};
+	partition@1 {
+		label = "firmware";
+		// 16M
+		reg = <0x20000 0x1000000>;
+		read-only;
+	};
+	partition@2 {
+		label = "root";
+		// 2G
+		reg = <0x1020000 0x80000000>;
+	};
+};

Documentation/devicetree/bindings/sound/brcm,bcm2835-i2s.txt

@@ -16,8 +16,8 @@ Example:
 
 bcm2835_i2s: i2s@7e203000 {
 	compatible = "brcm,bcm2835-i2s";
-	reg = <0x7e203000 0x20>,
+	reg = <0x7e203000 0x24>,
-	      <0x7e101098 0x02>;
+	      <0x7e101098 0x08>;
 
 	dmas = <&dma 2>,
 	       <&dma 3>;

Documentation/devicetree/bindings/usb/dwc3.txt

@@ -35,6 +35,8 @@ Optional properties:
 			LTSSM during USB3 Compliance mode.
  - snps,dis_u3_susphy_quirk: when set core will disable USB3 suspend phy.
  - snps,dis_u2_susphy_quirk: when set core will disable USB2 suspend phy.
+ - snps,dis_enblslpm_quirk: when set clears the enblslpm in GUSB2PHYCFG,
+			disabling the suspend signal to the PHY.
  - snps,is-utmi-l1-suspend: true when DWC3 asserts output signal
 			utmi_l1_suspend_n, false when asserts utmi_sleep_n
  - snps,hird-threshold: HIRD threshold

Documentation/devicetree/bindings/vendor-prefixes.txt

@@ -82,6 +82,7 @@ everspin	Everspin Technologies, Inc.
 excito	Excito
 fcs	Fairchild Semiconductor
 firefly	Firefly
+focaltech	FocalTech Systems Co.,Ltd
 fsl	Freescale Semiconductor
 GEFanuc	GE Fanuc Intelligent Platforms Embedded Systems, Inc.
 gef	GE Fanuc Intelligent Platforms Embedded Systems, Inc.

Documentation/filesystems/proc.txt

@@ -140,7 +140,8 @@ Table 1-1: Process specific entries in /proc
  stat		Process status
  statm		Process memory status information
  status		Process status in human readable form
- wchan		If CONFIG_KALLSYMS is set, a pre-decoded wchan
+ wchan		Present with CONFIG_KALLSYMS=y: it shows the kernel function
+		symbol the task is blocked in - or "0" if not blocked.
  pagemap	Page table
  stack		Report full stack trace, enable via CONFIG_STACKTRACE
  smaps		a extension based on maps, showing the memory consumption of
@@ -310,7 +311,7 @@ Table 1-4: Contents of the stat files (as of 2.6.30-rc7)
   blocked       bitmap of blocked signals
   sigign        bitmap of ignored signals
   sigcatch      bitmap of caught signals
-  wchan         address where process went to sleep
+  0		(place holder, used to be the wchan address, use /proc/PID/wchan instead)
   0             (place holder)
   0             (place holder)
   exit_signal   signal to send to parent thread on exit

Documentation/video4linux/bcm2835-v4l2.txt

@@ -0,0 +1,60 @@
+
+BCM2835 (aka Raspberry Pi) V4L2 driver
+======================================
+
+1. Copyright
+============
+
+Copyright © 2013 Raspberry Pi (Trading) Ltd.
+
+2. License
+==========
+
+This program is free software; you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation; either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program; if not, write to the Free Software
+Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+
+3. Quick Start
+==============
+
+You need a version 1.0 or later of v4l2-ctl, available from:
+	git://git.linuxtv.org/v4l-utils.git
+
+$ sudo modprobe bcm2835-v4l2
+
+Turn on the overlay:
+
+$ v4l2-ctl --overlay=1
+
+Turn off the overlay:
+
+$ v4l2-ctl --overlay=0
+
+Set the capture format for video:
+
+$ v4l2-ctl  --set-fmt-video=width=1920,height=1088,pixelformat=4
+
+(Note: 1088 not 1080).
+
+Capture:
+
+$ v4l2-ctl --stream-mmap=3 --stream-count=100 --stream-to=somefile.h264
+
+Stills capture:
+
+$ v4l2-ctl  --set-fmt-video=width=2592,height=1944,pixelformat=3
+$ v4l2-ctl --stream-mmap=3 --stream-count=1 --stream-to=somefile.jpg
+
+List of available formats:
+
+$ v4l2-ctl --list-formats

Makefile

@@ -1,6 +1,6 @@
 VERSION = 4
 PATCHLEVEL = 3
-SUBLEVEL = 0
+SUBLEVEL = 3
 EXTRAVERSION =
 NAME = Blurry Fish Butt
 

arch/arm/Kconfig

@@ -315,6 +315,49 @@ choice
 	default ARCH_VERSATILE if !MMU
 	default ARCH_MULTIPLATFORM if MMU
 
+config ARCH_BCM2708
+	bool "Broadcom BCM2708 family"
+	select CPU_V6
+	select ARM_AMBA
+	select CLKSRC_MMIO
+	select CLKSRC_OF if OF
+	select HAVE_SCHED_CLOCK
+	select NEED_MACH_GPIO_H
+	select NEED_MACH_MEMORY_H
+	select COMMON_CLK
+	select ARCH_HAS_CPUFREQ
+	select GENERIC_CLOCKEVENTS
+	select ARM_ERRATA_411920
+	select MACH_BCM2708
+	select MULTI_IRQ_HANDLER
+	select SPARSE_IRQ
+	select VC4
+	select FIQ
+	help
+	  This enables support for Broadcom BCM2708 boards.
+
+config ARCH_BCM2709
+	bool "Broadcom BCM2709 family"
+	select CPU_V7
+	select HAVE_SMP
+	select ARM_AMBA
+	select MIGHT_HAVE_CACHE_L2X0
+	select HAVE_SCHED_CLOCK
+	select NEED_MACH_MEMORY_H
+	select NEED_MACH_IO_H
+	select COMMON_CLK
+	select ARCH_HAS_CPUFREQ
+	select GENERIC_CLOCKEVENTS
+	select MACH_BCM2709
+	select VC4
+	select FIQ
+	select USE_OF
+	select ARCH_REQUIRE_GPIOLIB
+	select PINCTRL
+	select PINCTRL_BCM2835
+	help
+	  This enables support for Broadcom BCM2709 boards.
+
 config ARCH_MULTIPLATFORM
 	bool "Allow multiple platforms to be selected"
 	depends on MMU
@@ -828,6 +871,9 @@ config ARCH_VIRT
 # Kconfigs may be included either alphabetically (according to the
 # plat- suffix) or along side the corresponding mach-* source.
 #
+source "arch/arm/mach-bcm2708/Kconfig"
+source "arch/arm/mach-bcm2709/Kconfig"
+
 source "arch/arm/mach-mvebu/Kconfig"
 
 source "arch/arm/mach-alpine/Kconfig"

arch/arm/Kconfig.debug

@@ -1247,6 +1247,14 @@ choice
 		  options; the platform specific options are deprecated
 		  and will be soon removed.
 
+	config DEBUG_BCM2708_UART0
+		bool "Broadcom BCM270X UART0 (PL011)"
+		depends on ARCH_BCM2708 || ARCH_BCM2709
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to UART 0. The port must have been initialised
+		  by the boot-loader before use.
+
 endchoice
 
 config DEBUG_AT91_UART

arch/arm/Makefile

@@ -154,6 +154,8 @@ textofs-$(CONFIG_ARCH_AXXIA) := 0x00308000
 
 # Machine directory name.  This list is sorted alphanumerically
 # by CONFIG_* macro name.
+machine-$(CONFIG_ARCH_BCM2708)		+= bcm2708
+machine-$(CONFIG_ARCH_BCM2709)		+= bcm2709
 machine-$(CONFIG_ARCH_ALPINE)		+= alpine
 machine-$(CONFIG_ARCH_AT91)		+= at91
 machine-$(CONFIG_ARCH_AXXIA)		+= axxia

arch/arm/boot/dts/Makefile

@@ -1,5 +1,26 @@
 ifeq ($(CONFIG_OF),y)
 
+dtb-$(CONFIG_ARCH_BCM2708) += bcm2708-rpi-b.dtb
+dtb-$(CONFIG_ARCH_BCM2708) += bcm2708-rpi-b-plus.dtb
+dtb-$(CONFIG_ARCH_BCM2708) += bcm2708-rpi-cm.dtb
+dtb-$(CONFIG_ARCH_BCM2835) += bcm2835-rpi-cm.dtb
+dtb-$(CONFIG_ARCH_BCM2709) += bcm2709-rpi-2-b.dtb
+dtb-$(CONFIG_ARCH_BCM2709) += bcm2710-rpi-3-b.dtb
+
+# Raspberry Pi
+ifeq ($(CONFIG_ARCH_BCM2708),y)
+   RPI_DT_OVERLAYS=y
+endif
+ifeq ($(CONFIG_ARCH_BCM2709),y)
+   RPI_DT_OVERLAYS=y
+endif
+ifeq ($(CONFIG_ARCH_BCM2835),y)
+   RPI_DT_OVERLAYS=y
+endif
+ifeq ($(RPI_DT_OVERLAYS),y)
+    dts-dirs += overlays
+endif
+
 dtb-$(CONFIG_ARCH_ALPINE) += \
 	alpine-db.dtb
 dtb-$(CONFIG_MACH_ASM9260) += \
@@ -738,7 +759,17 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += \
 	mt8127-moose.dtb \
 	mt8135-evbp1.dtb
 dtb-$(CONFIG_ARCH_ZX) += zx296702-ad1.dtb
+
+targets += dtbs dtbs_install
+targets += $(dtb-y)
+
 endif
 
 always		:= $(dtb-y)
+subdir-y	:= $(dts-dirs)
 clean-files	:= *.dtb
+
+# Enable fixups to support overlays on BCM2708 platforms
+ifeq ($(RPI_DT_OVERLAYS),y)
+	DTC_FLAGS ?= -@
+endif

arch/arm/boot/dts/bcm2708-rpi-b-plus.dts

@@ -0,0 +1,149 @@
+/dts-v1/;
+
+#include "bcm2708.dtsi"
+
+/ {
+	compatible = "brcm,bcm2708";
+	model = "Raspberry Pi Model B+";
+};
+
+&gpio {
+	sdhost_pins: sdhost_pins {
+		brcm,pins = <48 49 50 51 52 53>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_pins: spi0_pins {
+		brcm,pins = <9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_cs_pins: spi0_cs_pins {
+		brcm,pins = <8 7>;
+		brcm,function = <1>; /* output */
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+
+	i2s_pins: i2s {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <4>; /* alt0 */
+	};
+};
+
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_pins>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&fb {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
+	cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
+
+	spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <500000>;
+	};
+
+	spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <500000>;
+	};
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	#sound-dai-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+&random {
+	status = "okay";
+};
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "mmc0";
+		gpios = <&gpio 47 0>;
+	};
+
+	pwr_led: pwr {
+		label = "led1";
+		linux,default-trigger = "input";
+		gpios = <&gpio 35 0>;
+	};
+};
+
+/ {
+	__overrides__ {
+		uart0 = <&uart0>,"status";
+		uart0_clkrate = <&clk_uart0>,"clock-frequency:0";
+		i2s = <&i2s>,"status";
+		spi = <&spi0>,"status";
+		i2c0 = <&i2c0>,"status";
+		i2c1 = <&i2c1>,"status";
+		i2c2_iknowwhatimdoing = <&i2c2>,"status";
+		i2c0_baudrate = <&i2c0>,"clock-frequency:0";
+		i2c1_baudrate = <&i2c1>,"clock-frequency:0";
+		i2c2_baudrate = <&i2c2>,"clock-frequency:0";
+		core_freq = <&clk_core>,"clock-frequency:0";
+
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+
+		pwr_led_gpio = <&pwr_led>,"gpios:4";
+		pwr_led_activelow = <&pwr_led>,"gpios:8";
+		pwr_led_trigger = <&pwr_led>,"linux,default-trigger";
+
+		audio = <&audio>,"status";
+		watchdog = <&watchdog>,"status";
+		random = <&random>,"status";
+		sd_overclock = <&sdhost>,"brcm,overclock-50:0";
+		sd_force_pio = <&sdhost>,"brcm,force-pio?";
+		sd_pio_limit = <&sdhost>,"brcm,pio-limit:0";
+		sd_debug     = <&sdhost>,"brcm,debug";
+	};
+};

arch/arm/boot/dts/bcm2708-rpi-b.dts

@@ -0,0 +1,139 @@
+/dts-v1/;
+
+#include "bcm2708.dtsi"
+
+/ {
+	compatible = "brcm,bcm2708";
+	model = "Raspberry Pi Model B";
+};
+
+&gpio {
+	sdhost_pins: sdhost_pins {
+		brcm,pins = <48 49 50 51 52 53>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_pins: spi0_pins {
+		brcm,pins = <9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_cs_pins: spi0_cs_pins {
+		brcm,pins = <8 7>;
+		brcm,function = <1>; /* output */
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+
+	i2s_pins: i2s {
+		brcm,pins = <28 29 30 31>;
+		brcm,function = <6>; /* alt2 */
+	};
+};
+
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_pins>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&fb {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
+	cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
+
+	spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <500000>;
+	};
+
+	spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <500000>;
+	};
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	#sound-dai-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+&random {
+	status = "okay";
+};
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "mmc0";
+		gpios = <&gpio 16 1>;
+	};
+};
+
+/ {
+	__overrides__ {
+		uart0 = <&uart0>,"status";
+		uart0_clkrate = <&clk_uart0>,"clock-frequency:0";
+		i2s = <&i2s>,"status";
+		spi = <&spi0>,"status";
+		i2c0 = <&i2c0>,"status";
+		i2c1 = <&i2c1>,"status";
+		i2c2_iknowwhatimdoing = <&i2c2>,"status";
+		i2c0_baudrate = <&i2c0>,"clock-frequency:0";
+		i2c1_baudrate = <&i2c1>,"clock-frequency:0";
+		i2c2_baudrate = <&i2c2>,"clock-frequency:0";
+		core_freq = <&clk_core>,"clock-frequency:0";
+
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+
+		audio = <&audio>,"status";
+		watchdog = <&watchdog>,"status";
+		random = <&random>,"status";
+		sd_overclock = <&sdhost>,"brcm,overclock-50:0";
+		sd_force_pio = <&sdhost>,"brcm,force-pio?";
+		sd_pio_limit = <&sdhost>,"brcm,pio-limit:0";
+		sd_debug     = <&sdhost>,"brcm,debug";
+	};
+};

arch/arm/boot/dts/bcm2708-rpi-cm.dts

@@ -0,0 +1,101 @@
+/dts-v1/;
+
+#include "bcm2708-rpi-cm.dtsi"
+
+/ {
+	model = "Raspberry Pi Compute Module";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&gpio {
+	spi0_pins: spi0_pins {
+		brcm,pins = <9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_cs_pins: spi0_cs_pins {
+		brcm,pins = <8 7>;
+		brcm,function = <1>; /* output */
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+
+	i2s_pins: i2s {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <4>; /* alt0 */
+	};
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
+	cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
+
+	spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <500000>;
+	};
+
+	spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <500000>;
+	};
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	#sound-dai-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+&random {
+	status = "okay";
+};
+
+/ {
+	__overrides__ {
+		uart0 = <&uart0>,"status";
+		uart0_clkrate = <&clk_uart0>,"clock-frequency:0";
+		i2s = <&i2s>,"status";
+		spi = <&spi0>,"status";
+		i2c0 = <&i2c0>,"status";
+		i2c1 = <&i2c1>,"status";
+		i2c2_iknowwhatimdoing = <&i2c2>,"status";
+		i2c0_baudrate = <&i2c0>,"clock-frequency:0";
+		i2c1_baudrate = <&i2c1>,"clock-frequency:0";
+		i2c2_baudrate = <&i2c2>,"clock-frequency:0";
+	};
+};

arch/arm/boot/dts/bcm2708-rpi-cm.dtsi

@@ -0,0 +1,53 @@
+#include "bcm2708.dtsi"
+
+&gpio {
+	sdhost_pins: sdhost_pins {
+		brcm,pins = <48 49 50 51 52 53>;
+		brcm,function = <4>; /* alt0 */
+	};
+};
+
+&gpio {
+	sdhost_pins: sdhost_pins {
+		brcm,pins = <48 49 50 51 52 53>;
+		brcm,function = <4>; /* alt0 */
+	};
+};
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "mmc0";
+		gpios = <&gpio 47 0>;
+	};
+};
+
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_pins>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+};
+
+&fb {
+	status = "okay";
+};
+
+/ {
+	__overrides__ {
+		core_freq = <&clk_core>,"clock-frequency:0";
+
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+
+		audio = <&audio>,"status";
+		watchdog = <&watchdog>,"status";
+		random = <&random>,"status";
+		sd_overclock = <&sdhost>,"brcm,overclock-50:0";
+		sd_force_pio = <&sdhost>,"brcm,force-pio?";
+		sd_pio_limit = <&sdhost>,"brcm,pio-limit:0";
+		sd_debug     = <&sdhost>,"brcm,debug";
+	};
+};

arch/arm/boot/dts/bcm2708.dtsi

@@ -0,0 +1,40 @@
+#include "bcm2708_common.dtsi"
+
+/ {
+	compatible = "brcm,bcm2708";
+	model = "BCM2708";
+
+	chosen {
+		/* No padding required - the boot loader can do that. */
+		bootargs = "";
+	};
+
+	soc {
+		ranges = <0x7e000000 0x20000000 0x01000000>;
+
+		timer@7e003000 {
+			compatible = "brcm,bcm2835-system-timer";
+			reg = <0x7e003000 0x1000>;
+			interrupts = <1 0>, <1 1>, <1 2>, <1 3>;
+			clock-frequency = <1000000>;
+		};
+
+		arm-pmu {
+			compatible = "arm,arm1176-pmu";
+		};
+
+		gpiomem {
+			compatible = "brcm,bcm2835-gpiomem";
+			reg = <0x7e200000 0x1000>;
+			status = "okay";
+		};
+	};
+};
+
+&intc {
+	compatible = "brcm,bcm2835-armctrl-ic";
+};
+
+&watchdog {
+	status = "okay";
+};

arch/arm/boot/dts/bcm2708_common.dtsi

@@ -0,0 +1,349 @@
+#include "skeleton.dtsi"
+
+/ {
+	interrupt-parent = <&intc>;
+
+	aliases {
+		audio = &audio;
+		sound = &sound;
+		soc = &soc;
+		dma = &dma;
+		intc = &intc;
+		watchdog = &watchdog;
+		random = &random;
+		mailbox = &mailbox;
+		gpio = &gpio;
+		uart0 = &uart0;
+		sdhost = &sdhost;
+		i2s  = &i2s;
+		spi0 = &spi0;
+		i2c0 = &i2c0;
+		uart1 = &uart1;
+		mmc = &mmc;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
+		usb = &usb;
+		leds = &leds;
+		fb = &fb;
+		vchiq = &vchiq;
+		thermal = &thermal;
+		clocks = &clocks;
+	};
+
+	/* Onboard audio */
+	audio: audio {
+		compatible = "brcm,bcm2835-audio";
+		brcm,pwm-channels = <8>;
+		status = "disabled";
+	};
+
+	/* External sound card */
+	sound: sound {
+	};
+
+	soc: soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		dma: dma@7e007000 {
+			compatible = "brcm,bcm2835-dma";
+			reg = <0x7e007000 0xf00>;
+			interrupts = <1 16>,
+				     <1 17>,
+				     <1 18>,
+				     <1 19>,
+				     <1 20>,
+				     <1 21>,
+				     <1 22>,
+				     <1 23>,
+				     <1 24>,
+				     <1 25>,
+				     <1 26>,
+				     <1 27>;
+
+			#dma-cells = <1>;
+			brcm,dma-channel-mask = <0x0f35>;
+		};
+
+		intc: interrupt-controller@7e00b200 {
+			compatible = "brcm,bcm2708-armctrl-ic";
+			reg = <0x7e00b200 0x200>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		mailbox: mailbox@7e00b800 {
+			compatible = "brcm,bcm2835-mbox";
+			reg = <0x7e00b880 0x40>;
+			interrupts = <0 1>;
+			#mbox-cells = <0>;
+		};
+
+		watchdog: watchdog@7e100000 {
+			compatible = "brcm,bcm2835-pm-wdt";
+			reg = <0x7e100000 0x28>;
+			status = "disabled";
+		};
+
+		cprman: cprman@7e101000 {
+			compatible = "brcm,bcm2835-cprman";
+			#clock-cells = <1>;
+			reg = <0x7e101000 0x2000>;
+
+			/* CPRMAN derives everything from the platform's
+			 * oscillator.
+			 */
+			clocks = <&clk_osc>;
+			status = "disabled";
+		};
+
+		random: rng@7e104000 {
+			compatible = "brcm,bcm2835-rng";
+			reg = <0x7e104000 0x10>;
+			status = "disabled";
+		};
+
+		gpio: gpio@7e200000 {
+			compatible = "brcm,bcm2835-gpio";
+			reg = <0x7e200000 0xb4>;
+			interrupts = <2 17>, <2 18>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		uart0: uart@7e201000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x7e201000 0x1000>;
+			interrupts = <2 25>;
+			clocks = <&clk_uart0 &clk_apb_p>;
+			clock-names = "uartclk","apb_pclk";
+			arm,primecell-periphid = <0x00241011>; // For an explanation, see
+			// https://github.com/raspberrypi/linux/commit/13731d862cf5219216533a3b0de052cee4cc5038
+			status = "disabled";
+		};
+
+		sdhost: sdhost@7e202000 {
+			compatible = "brcm,bcm2835-sdhost";
+			reg = <0x7e202000 0x100>;
+			interrupts = <2 24>;
+			clocks = <&clk_core>;
+			dmas = <&dma 13>,
+			       <&dma 13>;
+			dma-names = "tx", "rx";
+			brcm,overclock-50 = <0>;
+			brcm,pio-limit = <1>;
+			status = "disabled";
+		};
+
+		i2s: i2s@7e203000 {
+			compatible = "brcm,bcm2835-i2s";
+			reg = <0x7e203000 0x24>,
+			      <0x7e101098 0x08>;
+
+			dmas = <&dma 2>, <&dma 3>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
+		spi0: spi@7e204000 {
+			compatible = "brcm,bcm2835-spi";
+			reg = <0x7e204000 0x1000>;
+			interrupts = <2 22>;
+			clocks = <&clk_core>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+			/* the dma channels */
+			dmas = <&dma 6>, <&dma 7>;
+			dma-names = "tx", "rx";
+			/* the chipselects used - <0> means native GPIO
+			 * add more gpios if necessary as <&gpio 6 1>
+			 * (but do not forget to make them output!)
+			 */
+			cs-gpios = <0>, <0>;
+		};
+
+		i2c0: i2c@7e205000 {
+			compatible = "brcm,bcm2708-i2c";
+			reg = <0x7e205000 0x1000>;
+			interrupts = <2 21>;
+			clocks = <&clk_core>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		pwm: pwm@7e20c000 {
+			compatible = "brcm,bcm2835-pwm";
+			reg = <0x7e20c000 0x28>;
+			clocks = <&clk_pwm>;
+			#pwm-cells = <2>;
+			status = "disabled";
+		};
+
+		uart1: uart@7e215040 {
+			compatible = "brcm,bcm2835-aux-uart", "ns16550";
+			reg = <0x7e215040 0x40>;
+			interrupts = <1 29>;
+			clocks = <&clk_uart1>;
+			reg-shift = <2>;
+			no-loopback-test;
+			status = "disabled";
+	        };
+
+		mmc: mmc@7e300000 {
+			compatible = "brcm,bcm2835-mmc";
+			reg = <0x7e300000 0x100>;
+			interrupts = <2 30>;
+			clocks = <&clk_mmc>;
+			dmas = <&dma 11>,
+			       <&dma 11>;
+			dma-names = "tx", "rx";
+			brcm,overclock-50 = <0>;
+			status = "disabled";
+		};
+
+		i2c1: i2c@7e804000 {
+			compatible = "brcm,bcm2708-i2c";
+			reg = <0x7e804000 0x1000>;
+			interrupts = <2 21>;
+			clocks = <&clk_core>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c2: i2c@7e805000 {
+			// Beware - this is shared with the HDMI module.
+			// Careless use may break (really) your display.
+			// Caveat emptor.
+			compatible = "brcm,bcm2708-i2c";
+			reg = <0x7e805000 0x1000>;
+			interrupts = <2 21>;
+			clocks = <&clk_core>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		smi: smi@7e600000 {
+			compatible = "brcm,bcm2835-smi";
+			reg = <0x7e600000 0x44>, <0x7e1010b0 0x8>;
+			interrupts = <2 16>;
+			brcm,smi-clock-source = <6>;
+			brcm,smi-clock-divisor = <4>;
+			dmas = <&dma 4>;
+			dma-names = "rx-tx";
+			status = "disabled";
+		};
+
+		usb: usb@7e980000 {
+			compatible = "brcm,bcm2708-usb";
+			reg = <0x7e980000 0x10000>,
+			      <0x7e006000 0x1000>;
+			interrupts = <2 0>,
+				     <1 9>;
+		};
+
+		firmware: firmware {
+			compatible = "raspberrypi,bcm2835-firmware";
+			mboxes = <&mailbox>;
+		};
+
+		leds: leds {
+			compatible = "gpio-leds";
+		};
+
+		fb: fb {
+			compatible = "brcm,bcm2708-fb";
+			firmware = <&firmware>;
+			status = "disabled";
+		};
+
+		vchiq: vchiq {
+			compatible = "brcm,bcm2835-vchiq";
+			reg = <0x7e00b840 0xf>;
+			interrupts = <0 2>;
+			cache-line-size = <32>;
+			firmware = <&firmware>;
+		};
+
+		thermal: thermal {
+			compatible = "brcm,bcm2835-thermal";
+			firmware = <&firmware>;
+		};
+	};
+
+	clocks: clocks {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		clk_core: clock@0 {
+			compatible = "fixed-clock";
+			reg = <0>;
+			#clock-cells = <0>;
+			clock-output-names = "core";
+			clock-frequency = <250000000>;
+		};
+
+		clk_mmc: clock@1 {
+			compatible = "fixed-clock";
+			reg = <1>;
+			#clock-cells = <0>;
+			clock-output-names = "mmc";
+			clock-frequency = <250000000>;
+		};
+
+		clk_uart0: clock@2 {
+			compatible = "fixed-clock";
+			reg = <2>;
+			#clock-cells = <0>;
+			clock-output-names = "uart0_pclk";
+			clock-frequency = <3000000>;
+		};
+
+		clk_apb_p: clock@3 {
+			compatible = "fixed-clock";
+			reg = <3>;
+			#clock-cells = <0>;
+			clock-output-names = "apb_pclk";
+			clock-frequency = <126000000>;
+		};
+
+		clk_pwm: clock@4 {
+			compatible = "fixed-clock";
+			reg = <4>;
+			#clock-cells = <0>;
+			clock-output-names = "pwm";
+			clock-frequency = <100000000>;
+		};
+
+		clk_uart1: clock@5 {
+			compatible = "fixed-factor-clock";
+			reg = <5>;
+			clocks = <&clk_core>;
+			#clock-cells = <0>;
+			clock-div = <1>;
+			clock-mult = <2>;
+		};
+
+		/* The oscillator is the root of the clock tree. */
+		clk_osc: clock@6 {
+			compatible = "fixed-clock";
+			reg = <6>;
+			#clock-cells = <0>;
+			clock-output-names = "osc";
+			clock-frequency = <19200000>;
+		};
+	};
+
+	__overrides__ {
+		cache_line_size = <&vchiq>, "cache-line-size:0";
+	};
+};

arch/arm/boot/dts/bcm2709-rpi-2-b.dts

@@ -0,0 +1,149 @@
+/dts-v1/;
+
+#include "bcm2709.dtsi"
+
+/ {
+	compatible = "brcm,bcm2709";
+	model = "Raspberry Pi 2 Model B";
+};
+
+&gpio {
+	sdhost_pins: sdhost_pins {
+		brcm,pins = <48 49 50 51 52 53>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_pins: spi0_pins {
+		brcm,pins = <9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_cs_pins: spi0_cs_pins {
+		brcm,pins = <8 7>;
+		brcm,function = <1>; /* output */
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+
+	i2s_pins: i2s {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <4>; /* alt0 */
+	};
+};
+
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_pins>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&fb {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
+	cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
+
+	spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <500000>;
+	};
+
+	spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <500000>;
+	};
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	#sound-dai-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+&random {
+	status = "okay";
+};
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "mmc0";
+		gpios = <&gpio 47 0>;
+	};
+
+	pwr_led: pwr {
+		label = "led1";
+		linux,default-trigger = "input";
+		gpios = <&gpio 35 0>;
+	};
+};
+
+/ {
+	__overrides__ {
+		uart0 = <&uart0>,"status";
+		uart0_clkrate = <&clk_uart0>,"clock-frequency:0";
+		i2s = <&i2s>,"status";
+		spi = <&spi0>,"status";
+		i2c0 = <&i2c0>,"status";
+		i2c1 = <&i2c1>,"status";
+		i2c2_iknowwhatimdoing = <&i2c2>,"status";
+		i2c0_baudrate = <&i2c0>,"clock-frequency:0";
+		i2c1_baudrate = <&i2c1>,"clock-frequency:0";
+		i2c2_baudrate = <&i2c2>,"clock-frequency:0";
+		core_freq = <&clk_core>,"clock-frequency:0";
+
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+
+		pwr_led_gpio = <&pwr_led>,"gpios:4";
+		pwr_led_activelow = <&pwr_led>,"gpios:8";
+		pwr_led_trigger = <&pwr_led>,"linux,default-trigger";
+
+		audio = <&audio>,"status";
+		watchdog = <&watchdog>,"status";
+		random = <&random>,"status";
+		sd_overclock = <&sdhost>,"brcm,overclock-50:0";
+		sd_force_pio = <&sdhost>,"brcm,force-pio?";
+		sd_pio_limit = <&sdhost>,"brcm,pio-limit:0";
+		sd_debug     = <&sdhost>,"brcm,debug";
+	};
+};

arch/arm/boot/dts/bcm2709.dtsi

@@ -0,0 +1,80 @@
+#include "bcm2708_common.dtsi"
+
+/ {
+	compatible = "brcm,bcm2709";
+	model = "BCM2709";
+
+	chosen {
+		/* No padding required - the boot loader can do that. */
+		bootargs = "";
+	};
+
+	soc {
+		ranges = <0x7e000000 0x3f000000 0x01000000>;
+
+		arm-pmu {
+			compatible = "arm,cortex-a7-pmu";
+			interrupts = <3 9>;
+		};
+
+		gpiomem {
+			compatible = "brcm,bcm2835-gpiomem";
+			reg = <0x7e200000 0x1000>;
+			status = "okay";
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		clock-frequency = <19200000>;
+		interrupts = <3 0>, // PHYS_SECURE_PPI
+			     <3 1>, // PHYS_NONSECURE_PPI
+			     <3 3>, // VIRT_PPI
+			     <3 2>; // HYP_PPI
+		always-on;
+	};
+
+	cpus: cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		v7_cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0xf00>;
+			clock-frequency = <800000000>;
+		};
+
+		v7_cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0xf01>;
+			clock-frequency = <800000000>;
+		};
+
+		v7_cpu2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0xf02>;
+			clock-frequency = <800000000>;
+		};
+
+		v7_cpu3: cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0xf03>;
+			clock-frequency = <800000000>;
+		};
+	};
+
+	__overrides__ {
+		arm_freq = <&v7_cpu0>, "clock-frequency:0",
+		       <&v7_cpu1>, "clock-frequency:0",
+		       <&v7_cpu2>, "clock-frequency:0",
+		       <&v7_cpu3>, "clock-frequency:0";
+	};
+};
+
+&watchdog {
+	status = "okay";
+};

arch/arm/boot/dts/bcm2710-rpi-3-b.dts

@@ -0,0 +1,190 @@
+/dts-v1/;
+
+#include "bcm2710.dtsi"
+
+/ {
+	model = "Raspberry Pi 3 Model B";
+};
+
+&gpio {
+	sdhost_pins: sdhost_pins {
+		brcm,pins = <48 49 50 51 52 53>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_pins: spi0_pins {
+		brcm,pins = <7 8 9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+
+	i2s_pins: i2s {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	sdio_pins: sdio_pins {
+		brcm,pins =     <34 35 36 37 38 39>;
+		brcm,function = <7 7 7 7 7 7>; /* alt3 = SD1 */
+		brcm,pull =     <0 2 2 2 2 2>;
+	};
+
+	bt_pins: bt_pins {
+		brcm,pins =     <28 29 30 31 43>;
+		brcm,function = <6 6 6 6 4>;   /* alt2:PCM alt0:GPCLK2 */
+		brcm,pull =     <0 0 0 0 0>;
+	};
+
+	uart0_pins: uart0_pins {
+		brcm,pins = <32 33>;
+		brcm,function = <7>; /* alt3=UART0 */
+		brcm,pull = <0 0>;
+	};
+
+	uart1_pins: uart1_pins {
+		brcm,pins = <14 15>;
+		brcm,function = <2>; /* alt5=UART1 */
+		brcm,pull = <0 0>;
+	};
+};
+
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_pins>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&mmc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdio_pins>;
+	non-removable;
+	bus-width = <4>;
+	status = "okay";
+	brcm,overclock-50 = <0>;
+};
+
+&soc {
+	virtgpio: virtgpio {
+		compatible = "brcm,bcm2835-virtgpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+		firmware = <&firmware>;
+		status = "okay";
+	};
+};
+
+&fb {
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins &bt_pins>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins>;
+	cs-gpios = <0 0>;
+
+	spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <500000>;
+	};
+
+	spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <500000>;
+	};
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	#sound-dai-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+&random {
+	status = "okay";
+};
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "mmc0";
+		gpios = <&virtgpio 0 0>;
+	};
+};
+
+/ {
+	chosen {
+		bootargs = "8250.nr_uarts=1";
+	};
+};
+
+/ {
+	__overrides__ {
+		uart0 = <&uart0>,"status";
+		uart0_clkrate = <&clk_uart0>,"clock-frequency:0";
+		i2s = <&i2s>,"status";
+		spi = <&spi0>,"status";
+		i2c0 = <&i2c0>,"status";
+		i2c1 = <&i2c1>,"status";
+		i2c2_iknowwhatimdoing = <&i2c2>,"status";
+		i2c0_baudrate = <&i2c0>,"clock-frequency:0";
+		i2c1_baudrate = <&i2c1>,"clock-frequency:0";
+		i2c2_baudrate = <&i2c2>,"clock-frequency:0";
+		core_freq = <&clk_core>,"clock-frequency:0";
+
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+
+		audio = <&audio>,"status";
+		watchdog = <&watchdog>,"status";
+		random = <&random>,"status";
+		sd_overclock = <&sdhost>,"brcm,overclock-50:0";
+		sd_force_pio = <&sdhost>,"brcm,force-pio?";
+		sd_pio_limit = <&sdhost>,"brcm,pio-limit:0";
+		sd_debug     = <&sdhost>,"brcm,debug";
+	};
+};

arch/arm/boot/dts/bcm2710.dtsi

@@ -0,0 +1,76 @@
+#include "bcm2708_common.dtsi"
+
+/ {
+	compatible = "brcm,bcm2710","brcm,bcm2709";
+	model = "BCM2710";
+
+	chosen {
+		/* No padding required - the boot loader can do that. */
+		bootargs = "";
+	};
+
+	soc {
+		ranges = <0x7e000000 0x3f000000 0x01000000>;
+
+		arm-pmu {
+			compatible = "arm,cortex-a7-pmu";
+			interrupts = <3 9>;
+		};
+
+		gpiomem {
+			compatible = "brcm,bcm2835-gpiomem";
+			reg = <0x7e200000 0x1000>;
+			status = "okay";
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		clock-frequency = <19200000>;
+		interrupts = <3 0>, // PHYS_SECURE_PPI
+			     <3 1>, // PHYS_NONSECURE_PPI
+			     <3 3>, // VIRT_PPI
+			     <3 2>; // HYP_PPI
+		always-on;
+	};
+
+	cpus: cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		v7_cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x000>;
+			clock-frequency = <800000000>;
+		};
+
+		v7_cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x001>;
+			clock-frequency = <800000000>;
+		};
+
+		v7_cpu2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x002>;
+			clock-frequency = <800000000>;
+		};
+
+		v7_cpu3: cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x003>;
+			clock-frequency = <800000000>;
+		};
+	};
+
+	__overrides__ {
+		arm_freq = <&v7_cpu0>, "clock-frequency:0",
+		       <&v7_cpu1>, "clock-frequency:0",
+		       <&v7_cpu2>, "clock-frequency:0",
+		       <&v7_cpu3>, "clock-frequency:0";
+	};
+};

arch/arm/boot/dts/bcm2835-rpi-b-plus.dts

@@ -1,30 +1,128 @@
 /dts-v1/;
-#include "bcm2835-rpi.dtsi"
+#include "bcm2835.dtsi"
 
 / {
 	compatible = "raspberrypi,model-b-plus", "brcm,bcm2835";
 	model = "Raspberry Pi Model B+";
-
-	leds {
-		act {
-			gpios = <&gpio 47 0>;
-		};
-
-		pwr {
-			label = "PWR";
-			gpios = <&gpio 35 0>;
-			default-state = "keep";
-			linux,default-trigger = "default-on";
-		};
-	};
 };
 
 &gpio {
-	pinctrl-0 = <&gpioout &alt0 &i2s_alt0 &alt3>;
+	spi0_pins: spi0_pins {
+		brcm,pins = <7 8 9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
 
-	/* I2S interface */
+	i2c0_pins: i2c0 {
-	i2s_alt0: i2s_alt0 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+
+	i2s_pins: i2s {
 		brcm,pins = <18 19 20 21>;
-		brcm,function = <BCM2835_FSEL_ALT0>;
+		brcm,function = <4>; /* alt0 */
+	};
+};
+
+&mmc {
+	status = "okay";
+	bus-width = <4>;
+};
+
+&fb {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins>;
+
+	spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <500000>;
+	};
+
+	spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <500000>;
+	};
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	#sound-dai-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "mmc0";
+		gpios = <&gpio 47 0>;
+	};
+
+	pwr_led: pwr {
+		label = "led1";
+		linux,default-trigger = "input";
+		gpios = <&gpio 35 0>;
+	};
+};
+
+/ {
+	__overrides__ {
+		uart0 = <&uart0>,"status";
+		uart0_clkrate = <&clk_uart0>,"clock-frequency:0";
+		uart1_clkrate = <&uart1>,"clock-frequency:0";
+		i2s = <&i2s>,"status";
+		spi = <&spi0>,"status";
+		i2c0 = <&i2c0>,"status";
+		i2c1 = <&i2c1>,"status";
+		i2c2_iknowwhatimdoing = <&i2c2>,"status";
+		i2c0_baudrate = <&i2c0>,"clock-frequency:0";
+		i2c1_baudrate = <&i2c1>,"clock-frequency:0";
+		i2c2_baudrate = <&i2c2>,"clock-frequency:0";
+		core_freq = <&clk_core>,"clock-frequency:0";
+
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+
+		pwr_led_gpio = <&pwr_led>,"gpios:4";
+		pwr_led_activelow = <&pwr_led>,"gpios:8";
+		pwr_led_trigger = <&pwr_led>,"linux,default-trigger";
+
+		audio = <&audio>,"status";
+		watchdog = <&watchdog>,"status";
+		random = <&random>,"status";
 	};
 };

arch/arm/boot/dts/bcm2835-rpi-b.dts

@@ -1,23 +1,118 @@
 /dts-v1/;
-#include "bcm2835-rpi.dtsi"
+#include "bcm2835.dtsi"
 
 / {
 	compatible = "raspberrypi,model-b", "brcm,bcm2835";
 	model = "Raspberry Pi Model B";
-
-	leds {
-		act {
-			gpios = <&gpio 16 1>;
-		};
-	};
 };
 
 &gpio {
-	pinctrl-0 = <&gpioout &alt0 &i2s_alt2 &alt3>;
+	spi0_pins: spi0_pins {
+		brcm,pins = <7 8 9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
 
-	/* I2S interface */
+	i2c0_pins: i2c0 {
-	i2s_alt2: i2s_alt2 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+
+	i2s_pins: i2s {
 		brcm,pins = <28 29 30 31>;
-		brcm,function = <BCM2835_FSEL_ALT2>;
+		brcm,function = <6>; /* alt2 */
+	};
+};
+
+&mmc {
+	status = "okay";
+	bus-width = <4>;
+};
+
+&fb {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins>;
+
+	spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <500000>;
+	};
+
+	spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <500000>;
+	};
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	#sound-dai-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "mmc0";
+		gpios = <&gpio 16 1>;
+	};
+};
+
+/ {
+	__overrides__ {
+		uart0 = <&uart0>,"status";
+		uart0_clkrate = <&clk_uart0>,"clock-frequency:0";
+		uart1_clkrate = <&uart1>,"clock-frequency:0";
+		i2s = <&i2s>,"status";
+		spi = <&spi0>,"status";
+		i2c0 = <&i2c0>,"status";
+		i2c1 = <&i2c1>,"status";
+		i2c2_iknowwhatimdoing = <&i2c2>,"status";
+		i2c0_baudrate = <&i2c0>,"clock-frequency:0";
+		i2c1_baudrate = <&i2c1>,"clock-frequency:0";
+		i2c2_baudrate = <&i2c2>,"clock-frequency:0";
+		core_freq = <&clk_core>,"clock-frequency:0";
+
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+
+		audio = <&audio>,"status";
+		watchdog = <&watchdog>,"status";
+		random = <&random>,"status";
 	};
 };

arch/arm/boot/dts/bcm2835-rpi-cm.dts

@@ -0,0 +1,93 @@
+/dts-v1/;
+
+#include "bcm2835-rpi-cm.dtsi"
+
+/ {
+	model = "Raspberry Pi Compute Module";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&gpio {
+	spi0_pins: spi0_pins {
+		brcm,pins = <7 8 9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+
+	i2s_pins: i2s {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <4>; /* alt0 */
+	};
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins>;
+
+	spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <500000>;
+	};
+
+	spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <500000>;
+	};
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	#sound-dai-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+/ {
+	__overrides__ {
+		uart0 = <&uart0>,"status";
+		uart0_clkrate = <&clk_uart0>,"clock-frequency:0";
+		uart1_clkrate = <&uart1>,"clock-frequency:0";
+		i2s = <&i2s>,"status";
+		spi = <&spi0>,"status";
+		i2c0 = <&i2c0>,"status";
+		i2c1 = <&i2c1>,"status";
+		i2c2_iknowwhatimdoing = <&i2c2>,"status";
+		i2c0_baudrate = <&i2c0>,"clock-frequency:0";
+		i2c1_baudrate = <&i2c1>,"clock-frequency:0";
+		i2c2_baudrate = <&i2c2>,"clock-frequency:0";
+		core_freq = <&clk_core>,"clock-frequency:0";
+	};
+};

arch/arm/boot/dts/bcm2835-rpi-cm.dtsi

@@ -0,0 +1,30 @@
+#include "bcm2835.dtsi"
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "mmc0";
+		gpios = <&gpio 47 0>;
+	};
+};
+
+&mmc {
+	status = "okay";
+	bus-width = <4>;
+};
+
+&fb {
+	status = "okay";
+};
+
+/ {
+	__overrides__ {
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+
+		audio = <&audio>,"status";
+		watchdog = <&watchdog>,"status";
+		random = <&random>,"status";
+	};
+};

arch/arm/boot/dts/bcm2835.dtsi

@@ -1,20 +1,15 @@
-#include <dt-bindings/pinctrl/bcm2835.h>
+#include "bcm2708_common.dtsi"
-#include "skeleton.dtsi"
 
 / {
 	compatible = "brcm,bcm2835";
 	model = "BCM2835";
-	interrupt-parent = <&intc>;
 
 	chosen {
-		bootargs = "earlyprintk console=ttyAMA0";
+		bootargs = "";
 	};
 
 	soc {
-		compatible = "simple-bus";
+		ranges = <0x7e000000 0x20000000 0x01000000>;
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges = <0x7e000000 0x20000000 0x02000000>;
 		dma-ranges = <0x40000000 0x00000000 0x20000000>;
 
 		timer@7e003000 {
@@ -24,169 +19,21 @@
 			clock-frequency = <1000000>;
 		};
 
-		dma: dma@7e007000 {
-			compatible = "brcm,bcm2835-dma";
-			reg = <0x7e007000 0xf00>;
-			interrupts = <1 16>,
-				     <1 17>,
-				     <1 18>,
-				     <1 19>,
-				     <1 20>,
-				     <1 21>,
-				     <1 22>,
-				     <1 23>,
-				     <1 24>,
-				     <1 25>,
-				     <1 26>,
-				     <1 27>,
-				     <1 28>;
-
-			#dma-cells = <1>;
-			brcm,dma-channel-mask = <0x7f35>;
-		};
-
-		intc: interrupt-controller@7e00b200 {
-			compatible = "brcm,bcm2835-armctrl-ic";
-			reg = <0x7e00b200 0x200>;
-			interrupt-controller;
-			#interrupt-cells = <2>;
-		};
-
-		watchdog@7e100000 {
-			compatible = "brcm,bcm2835-pm-wdt";
-			reg = <0x7e100000 0x28>;
-		};
-
-		rng@7e104000 {
-			compatible = "brcm,bcm2835-rng";
-			reg = <0x7e104000 0x10>;
-		};
-
-		mailbox: mailbox@7e00b800 {
-			compatible = "brcm,bcm2835-mbox";
-			reg = <0x7e00b880 0x40>;
-			interrupts = <0 1>;
-			#mbox-cells = <0>;
-		};
-
-		gpio: gpio@7e200000 {
-			compatible = "brcm,bcm2835-gpio";
-			reg = <0x7e200000 0xb4>;
-			/*
-			 * The GPIO IP block is designed for 3 banks of GPIOs.
-			 * Each bank has a GPIO interrupt for itself.
-			 * There is an overall "any bank" interrupt.
-			 * In order, these are GIC interrupts 17, 18, 19, 20.
-			 * Since the BCM2835 only has 2 banks, the 2nd bank
-			 * interrupt output appears to be mirrored onto the
-			 * 3rd bank's interrupt signal.
-			 * So, a bank0 interrupt shows up on 17, 20, and
-			 * a bank1 interrupt shows up on 18, 19, 20!
-			 */
-			interrupts = <2 17>, <2 18>, <2 19>, <2 20>;
-
-			gpio-controller;
-			#gpio-cells = <2>;
-
-			interrupt-controller;
-			#interrupt-cells = <2>;
-		};
-
-		uart@7e201000 {
-			compatible = "brcm,bcm2835-pl011", "arm,pl011", "arm,primecell";
-			reg = <0x7e201000 0x1000>;
-			interrupts = <2 25>;
-			clock-frequency = <3000000>;
-			arm,primecell-periphid = <0x00241011>;
-		};
-
-		i2s: i2s@7e203000 {
-			compatible = "brcm,bcm2835-i2s";
-			reg = <0x7e203000 0x20>,
-			      <0x7e101098 0x02>;
-
-			dmas = <&dma 2>,
-			       <&dma 3>;
-			dma-names = "tx", "rx";
-			status = "disabled";
-		};
-
-		spi: spi@7e204000 {
-			compatible = "brcm,bcm2835-spi";
-			reg = <0x7e204000 0x1000>;
-			interrupts = <2 22>;
-			clocks = <&clk_spi>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			status = "disabled";
-		};
-
-		i2c0: i2c@7e205000 {
-			compatible = "brcm,bcm2835-i2c";
-			reg = <0x7e205000 0x1000>;
-			interrupts = <2 21>;
-			clocks = <&clk_i2c>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			status = "disabled";
-		};
-
-		sdhci: sdhci@7e300000 {
-			compatible = "brcm,bcm2835-sdhci";
-			reg = <0x7e300000 0x100>;
-			interrupts = <2 30>;
-			clocks = <&clk_mmc>;
-			status = "disabled";
-		};
-
-		i2c1: i2c@7e804000 {
-			compatible = "brcm,bcm2835-i2c";
-			reg = <0x7e804000 0x1000>;
-			interrupts = <2 21>;
-			clocks = <&clk_i2c>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			status = "disabled";
-		};
-
-		usb@7e980000 {
-			compatible = "brcm,bcm2835-usb";
-			reg = <0x7e980000 0x10000>;
-			interrupts = <1 9>;
-		};
-
 		arm-pmu {
 			compatible = "arm,arm1176-pmu";
 		};
+
+		aux_enable: aux_enable@0x7e215004 {
+			compatible = "bcrm,bcm2835-aux-enable";
+			reg = <0x7e215004 0x04>;
+		};
+	};
 };
 
-	clocks {
+&intc {
-		compatible = "simple-bus";
+	compatible = "brcm,bcm2835-armctrl-ic";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		clk_mmc: clock@0 {
-			compatible = "fixed-clock";
-			reg = <0>;
-			#clock-cells = <0>;
-			clock-output-names = "mmc";
-			clock-frequency = <100000000>;
 };
 
-		clk_i2c: clock@1 {
+&watchdog {
-			compatible = "fixed-clock";
+	status = "okay";
-			reg = <1>;
-			#clock-cells = <0>;
-			clock-output-names = "i2c";
-			clock-frequency = <250000000>;
-		};
-
-		clk_spi: clock@2 {
-			compatible = "fixed-clock";
-			reg = <2>;
-			#clock-cells = <0>;
-			clock-output-names = "spi";
-			clock-frequency = <250000000>;
-		};
-	};
 };

arch/arm/boot/dts/exynos3250-monk.dts

@@ -161,6 +161,7 @@
 };
 
 &exynos_usbphy {
+	vbus-supply = <&safeout_reg>;
 	status = "okay";
 };
 

arch/arm/boot/dts/exynos3250-rinato.dts

@@ -153,6 +153,7 @@
 
 &exynos_usbphy {
 	status = "okay";
+	vbus-supply = <&safeout_reg>;
 };
 
 &hsotg {

arch/arm/boot/dts/exynos4210-trats.dts

@@ -251,6 +251,7 @@
 
 &exynos_usbphy {
 	status = "okay";
+	vbus-supply = <&safe1_sreg>;
 };
 
 &fimd {
@@ -448,7 +449,6 @@
 
 			safe1_sreg: ESAFEOUT1 {
 			     regulator-name = "SAFEOUT1";
-			     regulator-always-on;
 			};
 
 			safe2_sreg: ESAFEOUT2 {

arch/arm/boot/dts/exynos4210-universal_c210.dts

@@ -248,6 +248,7 @@
 
 &exynos_usbphy {
 	status = "okay";
+	vbus-supply = <&safeout1_reg>;
 };
 
 &fimd {
@@ -486,7 +487,6 @@
 
 			safeout1_reg: ESAFEOUT1 {
 				regulator-name = "SAFEOUT1";
-				regulator-always-on;
 			};
 
 			safeout2_reg: ESAFEOUT2 {

arch/arm/boot/dts/exynos4412-trats2.dts

@@ -391,6 +391,7 @@
 };
 
 &exynos_usbphy {
+	vbus-supply = <&esafeout1_reg>;
 	status = "okay";
 };
 

arch/arm/boot/dts/imx27.dtsi

@@ -486,7 +486,10 @@
 				compatible = "fsl,imx27-usb";
 				reg = <0x10024000 0x200>;
 				interrupts = <56>;
-				clocks = <&clks IMX27_CLK_USB_IPG_GATE>;
+				clocks = <&clks IMX27_CLK_USB_IPG_GATE>,
+					<&clks IMX27_CLK_USB_AHB_GATE>,
+					<&clks IMX27_CLK_USB_DIV>;
+				clock-names = "ipg", "ahb", "per";
 				fsl,usbmisc = <&usbmisc 0>;
 				status = "disabled";
 			};
@@ -495,7 +498,10 @@
 				compatible = "fsl,imx27-usb";
 				reg = <0x10024200 0x200>;
 				interrupts = <54>;
-				clocks = <&clks IMX27_CLK_USB_IPG_GATE>;
+				clocks = <&clks IMX27_CLK_USB_IPG_GATE>,
+					<&clks IMX27_CLK_USB_AHB_GATE>,
+					<&clks IMX27_CLK_USB_DIV>;
+				clock-names = "ipg", "ahb", "per";
 				fsl,usbmisc = <&usbmisc 1>;
 				dr_mode = "host";
 				status = "disabled";
@@ -505,7 +511,10 @@
 				compatible = "fsl,imx27-usb";
 				reg = <0x10024400 0x200>;
 				interrupts = <55>;
-				clocks = <&clks IMX27_CLK_USB_IPG_GATE>;
+				clocks = <&clks IMX27_CLK_USB_IPG_GATE>,
+					<&clks IMX27_CLK_USB_AHB_GATE>,
+					<&clks IMX27_CLK_USB_DIV>;
+				clock-names = "ipg", "ahb", "per";
 				fsl,usbmisc = <&usbmisc 2>;
 				dr_mode = "host";
 				status = "disabled";
@@ -515,7 +524,6 @@
 				#index-cells = <1>;
 				compatible = "fsl,imx27-usbmisc";
 				reg = <0x10024600 0x200>;
-				clocks = <&clks IMX27_CLK_USB_AHB_GATE>;
 			};
 
 			sahara2: sahara@10025000 {

arch/arm/boot/dts/omap5-uevm.dts

@@ -31,6 +31,24 @@
 		regulator-max-microvolt = <3000000>;
 	};
 
+	mmc3_pwrseq: sdhci0_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&clk32kgaudio>;
+		clock-names = "ext_clock";
+	};
+
+	vmmcsdio_fixed: fixedregulator-mmcsdio {
+		compatible = "regulator-fixed";
+		regulator-name = "vmmcsdio_fixed";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&gpio5 12 GPIO_ACTIVE_HIGH>;	/* gpio140 WLAN_EN */
+		enable-active-high;
+		startup-delay-us = <70000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_pins>;
+	};
+
 	/* HS USB Host PHY on PORT 2 */
 	hsusb2_phy: hsusb2_phy {
 		compatible = "usb-nop-xceiv";
@@ -197,12 +215,20 @@
 		>;
 	};
 
-	mcspi4_pins: pinmux_mcspi4_pins {
+	mmc3_pins: pinmux_mmc3_pins {
 		pinctrl-single,pins = <
-			0x164 (PIN_INPUT | MUX_MODE1)		/*  mcspi4_clk */
+			OMAP5_IOPAD(0x01a4, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_clk */
-			0x168 (PIN_INPUT | MUX_MODE1)		/*  mcspi4_simo */
+			OMAP5_IOPAD(0x01a6, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_cmd */
-			0x16a (PIN_INPUT | MUX_MODE1)		/*  mcspi4_somi */
+			OMAP5_IOPAD(0x01a8, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data0 */
-			0x16c (PIN_INPUT | MUX_MODE1)		/*  mcspi4_cs0 */
+			OMAP5_IOPAD(0x01aa, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data1 */
+			OMAP5_IOPAD(0x01ac, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data2 */
+			OMAP5_IOPAD(0x01ae, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data3 */
+		>;
+	};
+
+	wlan_pins: pinmux_wlan_pins {
+		pinctrl-single,pins = <
+			OMAP5_IOPAD(0x1bc, PIN_OUTPUT | MUX_MODE6) /* mcspi1_clk.gpio5_140 */
 		>;
 	};
 
@@ -276,6 +302,12 @@
 			0x1A (PIN_OUTPUT | MUX_MODE0) /* fref_clk1_out, USB hub clk */
 		>;
 	};
+
+	wlcore_irq_pin: pinmux_wlcore_irq_pin {
+		pinctrl-single,pins = <
+			OMAP5_IOPAD(0x040, WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE6)	/* llia_wakereqin.gpio1_wk14 */
+		>;
+	};
 };
 
 &mmc1 {
@@ -290,8 +322,25 @@
 };
 
 &mmc3 {
+	vmmc-supply = <&vmmcsdio_fixed>;
+	mmc-pwrseq = <&mmc3_pwrseq>;
 	bus-width = <4>;
-	ti,non-removable;
+	non-removable;
+	cap-power-off-card;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc3_pins &wlcore_irq_pin>;
+	interrupts-extended = <&gic GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH
+			       &omap5_pmx_core 0x168>;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+	wlcore: wlcore@2 {
+		compatible = "ti,wl1271";
+		reg = <2>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <14 IRQ_TYPE_LEVEL_HIGH>;	/* gpio 14 */
+		ref-clock-frequency = <26000000>;
+	};
 };
 
 &mmc4 {
@@ -598,11 +647,6 @@
 	pinctrl-0 = <&mcspi3_pins>;
 };
 
-&mcspi4 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mcspi4_pins>;
-};
-
 &uart1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart1_pins>;

arch/arm/boot/dts/overlays/Makefile

@@ -0,0 +1,80 @@
+ifeq ($(CONFIG_OF),y)
+
+# Overlays for the Raspberry Pi platform
+
+ifeq ($(CONFIG_ARCH_BCM2708),y)
+   RPI_DT_OVERLAYS=y
+endif
+ifeq ($(CONFIG_ARCH_BCM2709),y)
+   RPI_DT_OVERLAYS=y
+endif
+ifeq ($(CONFIG_ARCH_BCM2835),y)
+   RPI_DT_OVERLAYS=y
+endif
+
+dtb-$(RPI_DT_OVERLAYS) += ads7846-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += at86rf233-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += bmp085_i2c-sensor-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += dht11-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += enc28j60-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += gpio-ir-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += gpio-poweroff-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += hifiberry-amp-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += hifiberry-dac-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += hifiberry-dacplus-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += hifiberry-digi-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += hy28a-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += hy28b-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += i2c-rtc-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += i2c-gpio-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += i2c0-bcm2708-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += i2c1-bcm2708-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += i2s-mmap-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += iqaudio-dac-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += iqaudio-dacplus-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += lirc-rpi-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += mcp2515-can0-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += mcp2515-can1-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += mmc-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += mz61581-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += pi3-disable-bt-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += pi3-miniuart-bt-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += piscreen-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += piscreen2r-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += pitft28-capacitive-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += pitft28-resistive-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += pps-gpio-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += pwm-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += pwm-2chan-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += raspidac3-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += rpi-backlight-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += rpi-dac-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += rpi-display-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += rpi-ft5406-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += rpi-proto-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += rpi-sense-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += sdhost-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += sdio-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += smi-dev-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += smi-nand-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += smi-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += spi-gpio35-39-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += tinylcd35-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += uart1-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += vc4-kms-v3d-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += vga666-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += w1-gpio-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += w1-gpio-pullup-overlay.dtb
+
+targets += dtbs dtbs_install
+targets += $(dtb-y)
+
+endif
+
+always		:= $(dtb-y)
+clean-files	:= *.dtb
+
+# Enable fixups to support overlays on BCM2708 platforms
+ifeq ($(RPI_DT_OVERLAYS),y)
+	DTC_FLAGS ?= -@
+endif

arch/arm/boot/dts/overlays/README

@@ -0,0 +1,812 @@
+Introduction
+============
+
+This directory contains Device Tree overlays. Device Tree makes it possible
+to support many hardware configurations with a single kernel and without the
+need to explicitly load or blacklist kernel modules. Note that this isn't a
+"pure" Device Tree configuration (c.f. MACH_BCM2835) - some on-board devices
+are still configured by the board support code, but the intention is to
+eventually reach that goal.
+
+On Raspberry Pi, Device Tree usage is controlled from /boot/config.txt. By
+default, the Raspberry Pi kernel boots with device tree enabled. You can
+completely disable DT usage (for now) by adding:
+
+    device_tree=
+
+to your config.txt, which should cause your Pi to revert to the old way of
+doing things after a reboot.
+
+In /boot you will find a .dtb for each base platform. This describes the
+hardware that is part of the Raspberry Pi board. The loader (start.elf and its
+siblings) selects the .dtb file appropriate for the platform by name, and reads
+it into memory. At this point, all of the optional interfaces (i2c, i2s, spi)
+are disabled, but they can be enabled using Device Tree parameters:
+
+    dtparam=i2c=on,i2s=on,spi=on
+
+However, this shouldn't be necessary in many use cases because loading an
+overlay that requires one of those interfaces will cause it to be enabled
+automatically, and it is advisable to only enable interfaces if they are
+needed.
+
+Configuring additional, optional hardware is done using Device Tree overlays
+(see below).
+
+raspi-config
+============
+
+The Advanced Options section of the raspi-config utility can enable and disable
+Device Tree use, as well as toggling the I2C and SPI interfaces. Note that it
+is possible to both enable an interface and blacklist the driver, if for some
+reason you should want to defer the loading.
+
+Modules
+=======
+
+As well as describing the hardware, Device Tree also gives enough information
+to allow suitable driver modules to be located and loaded, with the corollary
+that unneeded modules are not loaded. As a result it should be possible to
+remove lines from /etc/modules, and /etc/modprobe.d/raspi-blacklist.conf can
+have its contents deleted (or commented out).
+
+Using Overlays
+==============
+
+Overlays are loaded using the "dtoverlay" directive. As an example, consider
+the popular lirc-rpi module, the Linux Infrared Remote Control driver. In the
+pre-DT world this would be loaded from /etc/modules, with an explicit
+"modprobe lirc-rpi" command, or programmatically by lircd. With DT enabled,
+this becomes a line in config.txt:
+
+    dtoverlay=lirc-rpi
+
+This causes the file /boot/overlays/lirc-rpi-overlay.dtb to be loaded. By
+default it will use GPIOs 17 (out) and 18 (in), but this can be modified using
+DT parameters:
+
+    dtoverlay=lirc-rpi,gpio_out_pin=17,gpio_in_pin=13
+
+Parameters always have default values, although in some cases (e.g. "w1-gpio")
+it is necessary to provided multiple overlays in order to get the desired
+behaviour. See the list of overlays below for a description of the parameters
+and their defaults.
+
+The Overlay and Parameter Reference
+===================================
+
+N.B. When editing this file, please preserve the indentation levels to make it
+simple to parse programmatically. NO HARD TABS.
+
+
+Name:   <The base DTB>
+Info:   Configures the base Raspberry Pi hardware
+Load:   <loaded automatically>
+Params:
+        audio                   Set to "on" to enable the onboard ALSA audio
+                                interface (default "off")
+
+        i2c_arm                 Set to "on" to enable the ARM's i2c interface
+                                (default "off")
+
+        i2c_vc                  Set to "on" to enable the i2c interface
+                                usually reserved for the VideoCore processor
+                                (default "off")
+
+        i2c                     An alias for i2c_arm
+
+        i2c_arm_baudrate        Set the baudrate of the ARM's i2c interface
+                                (default "100000")
+
+        i2c_vc_baudrate         Set the baudrate of the VideoCore i2c interface
+                                (default "100000")
+
+        i2c_baudrate            An alias for i2c_arm_baudrate
+
+        i2s                     Set to "on" to enable the i2s interface
+                                (default "off")
+
+        spi                     Set to "on" to enable the spi interfaces
+                                (default "off")
+
+        random                  Set to "on" to enable the hardware random
+                                number generator (default "on")
+
+        sd_overclock            Clock (in MHz) to use when the MMC framework
+                                requests 50MHz
+
+        sd_force_pio            Disable DMA support for SD driver (default off)
+
+        sd_pio_limit            Number of blocks above which to use DMA for
+                                SD card (default 1)
+
+        sd_debug                Enable debug output from SD driver (default off)
+
+        uart0                   Set to "off" to disable uart0 (default "on")
+
+        watchdog                Set to "on" to enable the hardware watchdog
+                                (default "off")
+
+        act_led_trigger         Choose which activity the LED tracks.
+                                Use "heartbeat" for a nice load indicator.
+                                (default "mmc")
+
+        act_led_activelow       Set to "on" to invert the sense of the LED
+                                (default "off")
+
+        act_led_gpio            Set which GPIO to use for the activity LED
+                                (in case you want to connect it to an external
+                                device)
+                                (default "16" on a non-Plus board, "47" on a
+                                Plus or Pi 2)
+
+        pwr_led_trigger
+        pwr_led_activelow
+        pwr_led_gpio
+                                As for act_led_*, but using the PWR LED.
+                                Not available on Model A/B boards.
+
+        N.B. It is recommended to only enable those interfaces that are needed.
+        Leaving all interfaces enabled can lead to unwanted behaviour (i2c_vc
+        interfering with Pi Camera, I2S and SPI hogging GPIO pins, etc.)
+        Note also that i2c, i2c_arm and i2c_vc are aliases for the physical
+        interfaces i2c0 and i2c1. Use of the numeric variants is still possible
+        but deprecated because the ARM/VC assignments differ between board
+        revisions. The same board-specific mapping applies to i2c_baudrate,
+        and the other i2c baudrate parameters.
+
+
+Name:   ads7846
+Info:   ADS7846 Touch controller
+Load:   dtoverlay=ads7846,<param>=<val>
+Params: cs                      SPI bus Chip Select (default 1)
+        speed                   SPI bus speed (default 2MHz, max 3.25MHz)
+        penirq                  GPIO used for PENIRQ. REQUIRED
+        penirq_pull             Set GPIO pull (default 0=none, 2=pullup)
+        swapxy                  Swap x and y axis
+        xmin                    Minimum value on the X axis (default 0)
+        ymin                    Minimum value on the Y axis (default 0)
+        xmax                    Maximum value on the X axis (default 4095)
+        ymax                    Maximum value on the Y axis (default 4095)
+        pmin                    Minimum reported pressure value (default 0)
+        pmax                    Maximum reported pressure value (default 65535)
+        xohms                   Touchpanel sensitivity (X-plate resistance)
+                                (default 400)
+
+        penirq is required and usually xohms (60-100) has to be set as well.
+        Apart from that, pmax (255) and swapxy are also common.
+        The rest of the calibration can be done with xinput-calibrator.
+        See: github.com/notro/fbtft/wiki/FBTFT-on-Raspian
+        Device Tree binding document:
+        www.kernel.org/doc/Documentation/devicetree/bindings/input/ads7846.txt
+
+
+Name:   at86rf233
+Info:   Configures the Atmel AT86RF233 802.15.4 low-power WPAN transceiver,
+        connected to spi0.0
+Load:   dtoverlay=at86rf233,<param>=<val>
+Params: interrupt               GPIO used for INT (default 23)
+        reset                   GPIO used for Reset (default 24)
+        sleep                   GPIO used for Sleep (default 25)
+        speed                   SPI bus speed in Hz (default 3000000)
+        trim                    Fine tuning of the internal capacitance
+                                arrays (0=+0pF, 15=+4.5pF, default 15)
+
+
+Name:   bmp085_i2c-sensor
+Info:   Configures the BMP085/BMP180 digital barometric pressure and temperature
+        sensors from Bosch Sensortec
+Load:   dtoverlay=bmp085_i2c-sensor
+Params: <None>
+
+
+Name:   dht11
+Info:   Overlay for the DHT11/DHT21/DHT22 humidity/temperature sensors
+        Also sometimes found with the part number(s) AM230x.
+Load:   dtoverlay=dht11,<param>=<val>
+Params: gpiopin                 GPIO connected to the sensor's DATA output.
+                                (default 4)
+
+
+[ The ds1307-rtc overlay has been deleted. See i2c-rtc. ]
+
+
+Name:   enc28j60
+Info:   Overlay for the Microchip ENC28J60 Ethernet Controller (SPI)
+Load:   dtoverlay=enc28j60,<param>=<val>
+Params: int_pin                 GPIO used for INT (default 25)
+
+        speed                   SPI bus speed (default 12000000)
+
+
+Name:   gpio-ir
+Info:   Use GPIO pin as rc-core style infrared receiver input. The rc-core-
+        based gpio_ir_recv driver maps received keys directly to a
+        /dev/input/event* device, all decoding is done by the kernel - LIRC is
+        not required! The key mapping and other decoding parameters can be
+        configured by "ir-keytable" tool.
+Load:   dtoverlay=gpio-ir,<param>=<val>
+Params: gpio_pin                Input pin number. Default is 18.
+
+        gpio_pull               Desired pull-up/down state (off, down, up)
+                                Default is "down".
+
+        rc-map-name             Default rc keymap (can also be changed by
+                                ir-keytable), defaults to "rc-rc6-mce"
+
+
+Name:   gpio-poweroff
+Info:   Drives a GPIO high or low on reboot
+Load:   dtoverlay=gpio-poweroff,<param>=<val>
+Params: gpiopin                 GPIO for signalling (default 26)
+
+        active_low              Set if the power control device requires a
+                                high->low transition to trigger a power-down.
+                                Note that this will require the support of a
+                                custom dt-blob.bin to prevent a power-down
+                                during the boot process, and that a reboot
+                                will also cause the pin to go low.
+
+
+Name:   hifiberry-amp
+Info:   Configures the HifiBerry Amp and Amp+ audio cards
+Load:   dtoverlay=hifiberry-amp
+Params: <None>
+
+
+Name:   hifiberry-dac
+Info:   Configures the HifiBerry DAC audio card
+Load:   dtoverlay=hifiberry-dac
+Params: <None>
+
+
+Name:   hifiberry-dacplus
+Info:   Configures the HifiBerry DAC+ audio card
+Load:   dtoverlay=hifiberry-dacplus,<param>=<val>
+Params: 24db_digital_gain       Allow gain to be applied via the PCM512x codec
+                                Digital volume control. Enable with
+                                "dtoverlay=hifiberry-dacplus,24db_digital_gain"
+                                (The default behaviour is that the Digital
+                                volume control is limited to a maximum of
+                                0dB. ie. it can attenuate but not provide
+                                gain. For most users, this will be desired
+                                as it will prevent clipping. By appending
+                                the 24dB_digital_gain parameter, the Digital
+                                volume control will allow up to 24dB of
+                                gain. If this parameter is enabled, it is the
+                                responsibility of the user to ensure that
+                                the Digital volume control is set to a value
+                                that does not result in clipping/distortion!)
+
+
+Name:   hifiberry-digi
+Info:   Configures the HifiBerry Digi audio card
+Load:   dtoverlay=hifiberry-digi
+Params: <None>
+
+
+Name:   hy28a
+Info:   HY28A - 2.8" TFT LCD Display Module by HAOYU Electronics
+        Default values match Texy's display shield
+Load:   dtoverlay=hy28a,<param>=<val>
+Params: speed                   Display SPI bus speed
+
+        rotate                  Display rotation {0,90,180,270}
+
+        fps                     Delay between frame updates
+
+        debug                   Debug output level {0-7}
+
+        xohms                   Touchpanel sensitivity (X-plate resistance)
+
+        resetgpio               GPIO used to reset controller
+
+        ledgpio                 GPIO used to control backlight
+
+
+Name:   hy28b
+Info:   HY28B - 2.8" TFT LCD Display Module by HAOYU Electronics
+        Default values match Texy's display shield
+Load:   dtoverlay=hy28b,<param>=<val>
+Params: speed                   Display SPI bus speed
+
+        rotate                  Display rotation {0,90,180,270}
+
+        fps                     Delay between frame updates
+
+        debug                   Debug output level {0-7}
+
+        xohms                   Touchpanel sensitivity (X-plate resistance)
+
+        resetgpio               GPIO used to reset controller
+
+        ledgpio                 GPIO used to control backlight
+
+
+Name:   i2c-gpio
+Info:   Adds support for software i2c controller on gpio pins
+Load:   dtoverlay=i2c-gpio,<param>=<val>
+Params: i2c_gpio_sda            GPIO used for I2C data (default "23")
+
+        i2c_gpio_scl            GPIO used for I2C clock (default "24")
+
+        i2c_gpio_delay_us       Clock delay in microseconds
+                                (default "2" = ~100kHz)
+
+
+Name:   i2c-rtc
+Info:   Adds support for a number of I2C Real Time Clock devices
+Load:   dtoverlay=i2c-rtc,<param>=<val>
+Params: ds1307                  Select the DS1307 device
+
+        ds3231                  Select the DS3231 device
+
+        mcp7941x                Select the MCP7941x device
+
+        pcf2127                 Select the PCF2127 device
+
+        pcf8523                 Select the PCF8523 device
+
+        pcf8563                 Select the PCF8563 device
+
+
+Name:   i2c0-bcm2708
+Info:   Enable the i2c_bcm2708 driver for the i2c0 bus
+Load:   dtoverlay=i2c0-bcm2708,<param>=<val>
+Params: sda0_pin                GPIO pin for SDA0 (0, 28 [or 44] - default 0)
+        scl0_pin                GPIO pin for SCL0 (1, 29 [or 45] - default 1)
+
+
+Name:   i2c1-bcm2708
+Info:   Enable the i2c_bcm2708 driver for the i2c1 bus
+Load:   dtoverlay=i2c1-bcm2708,<param>=<val>
+Params: sda1_pin                GPIO pin for SDA1 (2 or 44 - default 2)
+        scl1_pin                GPIO pin for SCL1 (3 or 45 - default 3)
+        pin_func                Alternative pin function (4 (alt0), 6 (alt2) -
+                                default 4)
+
+
+Name:   i2s-mmap
+Info:   Enables mmap support in the bcm2708-i2s driver
+Load:   dtoverlay=i2s-mmap
+Params: <None>
+
+
+Name:   iqaudio-dac
+Info:   Configures the IQaudio DAC audio card
+Load:   dtoverlay=iqaudio-dac
+Params: <None>
+
+
+Name:   iqaudio-dacplus
+Info:   Configures the IQaudio DAC+ audio card
+Load:   dtoverlay=iqaudio-dacplus,<param>=<val>
+Params: 24db_digital_gain       Allow gain to be applied via the PCM512x codec
+                                Digital volume control. Enable with
+                                "dtoverlay=iqaudio-dacplus,24db_digital_gain"
+                                (The default behaviour is that the Digital
+                                volume control is limited to a maximum of
+                                0dB. ie. it can attenuate but not provide
+                                gain. For most users, this will be desired
+                                as it will prevent clipping. By appending
+                                the 24db_digital_gain parameter, the Digital
+                                volume control will allow up to 24dB of
+                                gain. If this parameter is enabled, it is the
+                                responsibility of the user to ensure that
+                                the Digital volume control is set to a value
+                                that does not result in clipping/distortion!)
+
+
+Name:   lirc-rpi
+Info:   Configures lirc-rpi (Linux Infrared Remote Control for Raspberry Pi)
+        Consult the module documentation for more details.
+Load:   dtoverlay=lirc-rpi,<param>=<val>
+Params: gpio_out_pin            GPIO for output (default "17")
+
+        gpio_in_pin             GPIO for input (default "18")
+
+        gpio_in_pull            Pull up/down/off on the input pin
+                                (default "down")
+
+        sense                   Override the IR receive auto-detection logic:
+                                  "0" = force active-high
+                                  "1" = force active-low
+                                  "-1" = use auto-detection
+                                (default "-1")
+
+        softcarrier             Turn the software carrier "on" or "off"
+                                (default "on")
+
+        invert                  "on" = invert the output pin (default "off")
+
+        debug                   "on" = enable additional debug messages
+                                (default "off")
+
+
+Name:   mcp2515-can0
+Info:   Configures the MCP2515 CAN controller on spi0.0
+Load:   dtoverlay=mcp2515-can0,<param>=<val>
+Params: oscillator              Clock frequency for the CAN controller (Hz)
+
+        spimaxfrequency         Maximum SPI frequence (Hz)
+
+        interrupt               GPIO for interrupt signal
+
+
+Name:   mcp2515-can1
+Info:   Configures the MCP2515 CAN controller on spi0.1
+Load:   dtoverlay=mcp2515-can1,<param>=<val>
+Params: oscillator              Clock frequency for the CAN controller (Hz)
+
+        spimaxfrequency         Maximum SPI frequence (Hz)
+
+        interrupt               GPIO for interrupt signal
+
+
+Name:   mmc
+Info:   Selects the bcm2835-mmc SD/MMC driver, optionally with overclock
+Load:   dtoverlay=mmc,<param>=<val>
+Params: overclock_50            Clock (in MHz) to use when the MMC framework
+                                requests 50MHz
+
+
+Name:   mz61581
+Info:   MZ61581 display by Tontec
+Load:   dtoverlay=mz61581,<param>=<val>
+Params: speed                   Display SPI bus speed
+
+        rotate                  Display rotation {0,90,180,270}
+
+        fps                     Delay between frame updates
+
+        txbuflen                Transmit buffer length (default 32768)
+
+        debug                   Debug output level {0-7}
+
+        xohms                   Touchpanel sensitivity (X-plate resistance)
+
+
+[ The pcf2127-rtc overlay has been deleted. See i2c-rtc. ]
+
+
+[ The pcf8523-rtc overlay has been deleted. See i2c-rtc. ]
+
+
+[ The pcf8563-rtc overlay has been deleted. See i2c-rtc. ]
+
+
+Name:   pi3-disable-bt
+Info:   Disable Pi3 Bluetooth and restore UART0/ttyAMA0 over GPIOs 14 & 15
+        N.B. To disable the systemd service that initialises the modem so it
+        doesn't use the UART, use 'sudo systemctl disable hciuart'.
+Load:   dtoverlay=pi3-disable-bt
+Params: <None>
+
+
+Name:   pi3-miniuart-bt
+Info:   Switch Pi3 Bluetooth function to use the mini-UART (ttyS0) and restore
+        UART0/ttyAMA0 over GPIOs 14 & 15. Note that this may reduce the maximum
+        usable baudrate.
+        N.B. It is also necessary to edit /lib/systemd/system/hciuart.server
+        and replace ttyAMA0 with ttyS0.
+Load:   dtoverlay=pi3-miniuart-bt
+Params: <None>
+
+
+Name:   piscreen
+Info:   PiScreen display by OzzMaker.com
+Load:   dtoverlay=piscreen,<param>=<val>
+Params: speed                   Display SPI bus speed
+
+        rotate                  Display rotation {0,90,180,270}
+
+        fps                     Delay between frame updates
+
+        debug                   Debug output level {0-7}
+
+        xohms                   Touchpanel sensitivity (X-plate resistance)
+
+
+Name:   piscreen2r
+Info:   PiScreen 2 with resistive TP display by OzzMaker.com
+Load:   dtoverlay=piscreen2r,<param>=<val>
+Params: speed                   Display SPI bus speed
+
+        rotate                  Display rotation {0,90,180,270}
+
+        fps                     Delay between frame updates
+
+        debug                   Debug output level {0-7}
+
+        xohms                   Touchpanel sensitivity (X-plate resistance)
+
+
+Name:   pitft28-capacitive
+Info:   Adafruit PiTFT 2.8" capacitive touch screen
+Load:   dtoverlay=pitft28-capacitive,<param>=<val>
+Params: speed                   Display SPI bus speed
+
+        rotate                  Display rotation {0,90,180,270}
+
+        fps                     Delay between frame updates
+
+        debug                   Debug output level {0-7}
+
+        touch-sizex             Touchscreen size x (default 240)
+
+        touch-sizey             Touchscreen size y (default 320)
+
+        touch-invx              Touchscreen inverted x axis
+
+        touch-invy              Touchscreen inverted y axis
+
+        touch-swapxy            Touchscreen swapped x y axis
+
+
+Name:   pitft28-resistive
+Info:   Adafruit PiTFT 2.8" resistive touch screen
+Load:   dtoverlay=pitft28-resistive,<param>=<val>
+Params: speed                   Display SPI bus speed
+
+        rotate                  Display rotation {0,90,180,270}
+
+        fps                     Delay between frame updates
+
+        debug                   Debug output level {0-7}
+
+
+Name:   pps-gpio
+Info:   Configures the pps-gpio (pulse-per-second time signal via GPIO).
+Load:   dtoverlay=pps-gpio,<param>=<val>
+Params: gpiopin                 Input GPIO (default "18")
+
+
+Name:   pwm
+Info:   Configures a single PWM channel
+        Legal pin,function combinations for each channel:
+          PWM0: 12,4(Alt0) 18,2(Alt5) 40,4(Alt0)            52,5(Alt1)
+          PWM1: 13,4(Alt0) 19,2(Alt5) 41,4(Alt0) 45,4(Alt0) 53,5(Alt1)
+        N.B.:
+          1) Pin 18 is the only one available on all platforms, and
+             it is the one used by the I2S audio interface.
+             Pins 12 and 13 might be better choices on an A+, B+ or Pi2.
+          2) The onboard analogue audio output uses both PWM channels.
+          3) So be careful mixing audio and PWM.
+          4) Currently the clock must have been enabled and configured
+             by other means.
+Load:   dtoverlay=pwm,<param>=<val>
+Params: pin                     Output pin (default 18) - see table
+        func                    Pin function (default 2 = Alt5) - see above
+        clock                   PWM clock frequency (informational)
+
+
+Name:   pwm-2chan
+Info:   Configures both PWM channels
+        Legal pin,function combinations for each channel:
+          PWM0: 12,4(Alt0) 18,2(Alt5) 40,4(Alt0)            52,5(Alt1)
+          PWM1: 13,4(Alt0) 19,2(Alt5) 41,4(Alt0) 45,4(Alt0) 53,5(Alt1)
+        N.B.:
+          1) Pin 18 is the only one available on all platforms, and
+             it is the one used by the I2S audio interface.
+             Pins 12 and 13 might be better choices on an A+, B+ or Pi2.
+          2) The onboard analogue audio output uses both PWM channels.
+          3) So be careful mixing audio and PWM.
+          4) Currently the clock must have been enabled and configured
+             by other means.
+Load:   dtoverlay=pwm-2chan,<param>=<val>
+Params: pin                     Output pin (default 18) - see table
+        pin2                    Output pin for other channel (default 19)
+        func                    Pin function (default 2 = Alt5) - see above
+        func2                   Function for pin2 (default 2 = Alt5)
+        clock                   PWM clock frequency (informational)
+
+
+Name:   raspidac3
+Info:   Configures the RaspiDAV Rev.3x audio card
+Load:   dtoverlay=raspidac3
+Params: <None>
+
+
+Name:   rpi-backlight
+Info:   Raspberry Pi official display backlight driver
+Load:   dtoverlay=rpi-backlight
+Params: <None>
+
+
+Name:   rpi-dac
+Info:   Configures the RPi DAC audio card
+Load:   dtoverlay=rpi-dac
+Params: <None>
+
+
+Name:   rpi-display
+Info:   RPi-Display - 2.8" Touch Display by Watterott
+Load:   dtoverlay=rpi-display,<param>=<val>
+Params: speed                   Display SPI bus speed
+
+        rotate                  Display rotation {0,90,180,270}
+
+        fps                     Delay between frame updates
+
+        debug                   Debug output level {0-7}
+
+        xohms                   Touchpanel sensitivity (X-plate resistance)
+
+
+Name:   rpi-ft5406
+Info:   Official Raspberry Pi display touchscreen
+Load:   dtoverlay=rpi-ft5406
+Params: <None>
+
+
+Name:   rpi-proto
+Info:   Configures the RPi Proto audio card
+Load:   dtoverlay=rpi-proto
+Params: <None>
+
+
+Name:   rpi-sense
+Info:   Raspberry Pi Sense HAT
+Load:   dtoverlay=rpi-sense
+Params: <None>
+
+
+Name:   sdhost
+Info:   Selects the bcm2835-sdhost SD/MMC driver, optionally with overclock
+Load:   dtoverlay=sdhost,<param>=<val>
+Params: overclock_50            Clock (in MHz) to use when the MMC framework
+                                requests 50MHz
+
+        force_pio               Disable DMA support (default off)
+
+        pio_limit               Number of blocks above which to use DMA
+                                (default 1)
+
+        debug                   Enable debug output (default off)
+
+
+Name:   sdio
+Info:   Selects the bcm2835-sdhost SD/MMC driver, optionally with overclock,
+        and enables SDIO via GPIOs 22-27.
+Load:   dtoverlay=sdio,<param>=<val>
+Params: overclock_50            SD Clock (in MHz) to use when the MMC framework
+                                requests 50MHz
+
+        sdio_overclock          SDIO Clock (in MHz) to use when the MMC
+                                framework requests 50MHz
+
+        force_pio               Disable DMA support (default off)
+
+        pio_limit               Number of blocks above which to use DMA
+                                (default 1)
+
+        debug                   Enable debug output (default off)
+
+        poll_once               Disable SDIO-device polling every second
+                                (default on: polling once at boot-time)
+
+        bus_width               Set the SDIO host bus width (default 4 bits)
+
+
+Name:   smi
+Info:   Enables the Secondary Memory Interface peripheral. Uses GPIOs 2-25!
+Load:   dtoverlay=smi
+Params: <None>
+
+
+Name:   smi-dev
+Info:   Enables the userspace interface for the SMI driver
+Load:   dtoverlay=smi-dev
+Params: <None>
+
+
+Name:   smi-nand
+Info:   Enables access to NAND flash via the SMI interface
+Load:   dtoverlay=smi-nand
+Params: <None>
+
+
+Name:   spi-gpio35-39
+Info:   move SPI function block to GPIO 35 to 39
+Load:   dtoverlay=spi-gpio35-39
+Params: <None>
+
+
+Name:   tinylcd35
+Info:   3.5" Color TFT Display by www.tinylcd.com
+        Options: Touch, RTC, keypad
+Load:   dtoverlay=tinylcd35,<param>=<val>
+Params: speed                   Display SPI bus speed
+
+        rotate                  Display rotation {0,90,180,270}
+
+        fps                     Delay between frame updates
+
+        debug                   Debug output level {0-7}
+
+        touch                   Enable touch panel
+
+        touchgpio               Touch controller IRQ GPIO
+
+        xohms                   Touchpanel: Resistance of X-plate in ohms
+
+        rtc-pcf                 PCF8563 Real Time Clock
+
+        rtc-ds                  DS1307 Real Time Clock
+
+        keypad                  Enable keypad
+
+        Examples:
+            Display with touchpanel, PCF8563 RTC and keypad:
+                dtoverlay=tinylcd35,touch,rtc-pcf,keypad
+            Old touch display:
+                dtoverlay=tinylcd35,touch,touchgpio=3
+
+
+Name:   uart1
+Info:   Enable uart1 in place of uart0
+Load:   dtoverlay=uart1,<param>=<val>
+Params: txd1_pin                GPIO pin for TXD1 (14, 32 or 40 - default 14)
+
+        rxd1_pin                GPIO pin for RXD1 (15, 33 or 41 - default 15)
+
+
+Name:   vc4-kms-v3d
+Info:   Enable Eric Anholt's DRM VC4 HDMI/HVS/V3D driver. Running startx or
+        booting to GUI while this overlay is in use will cause interesting
+        lockups.
+Load:   dtoverlay=vc4-kms-v3d
+Params: <None>
+
+
+Name:   vga666
+Info:   Overlay for the Fen Logic VGA666 board
+        This uses GPIOs 2-21 (so no I2C), and activates the output 2-3 seconds
+        after the kernel has started.
+Load:   dtoverlay=vga666
+Params: <None>
+
+
+Name:   w1-gpio
+Info:   Configures the w1-gpio Onewire interface module.
+        Use this overlay if you *don't* need a GPIO to drive an external pullup.
+Load:   dtoverlay=w1-gpio,<param>=<val>
+Params: gpiopin                 GPIO for I/O (default "4")
+
+        pullup                  Non-zero, "on", or "y" to enable the parasitic
+                                power (2-wire, power-on-data) feature
+
+
+Name:   w1-gpio-pullup
+Info:   Configures the w1-gpio Onewire interface module.
+        Use this overlay if you *do* need a GPIO to drive an external pullup.
+Load:   dtoverlay=w1-gpio-pullup,<param>=<val>
+Params: gpiopin                 GPIO for I/O (default "4")
+
+        pullup                  Non-zero, "on", or "y" to enable the parasitic
+                                power (2-wire, power-on-data) feature
+
+        extpullup               GPIO for external pullup (default "5")
+
+
+Troubleshooting
+===============
+
+If you are experiencing problems that you think are DT-related, enable DT
+diagnostic output by adding this to /boot/config.txt:
+
+    dtdebug=on
+
+and rebooting. Then run:
+
+    sudo vcdbg log msg
+
+and look for relevant messages.
+
+Further reading
+===============
+
+This is only meant to be a quick introduction to the subject of Device Tree on
+Raspberry Pi. There is a more complete explanation here:
+
+http://www.raspberrypi.org/documentation/configuration/device-tree.md

arch/arm/boot/dts/overlays/ads7846-overlay.dts

@@ -0,0 +1,83 @@
+/*
+ * Generic Device Tree overlay for the ADS7846 touch controller
+ *
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
+
+	fragment@0 {
+		target = <&spi0>;
+		__overlay__ {
+			status = "okay";
+
+			spidev@0{
+				status = "disabled";
+			};
+
+			spidev@1{
+				status = "disabled";
+			};
+		};
+	};
+
+	fragment@1 {
+		target = <&gpio>;
+		__overlay__ {
+			ads7846_pins: ads7846_pins {
+				brcm,pins = <255>; /* illegal default value */
+				brcm,function = <0>; /* in */
+				brcm,pull = <0>; /* none */
+			};
+		};
+	};
+
+	fragment@2 {
+		target = <&spi0>;
+		__overlay__ {
+			/* needed to avoid dtc warning */
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			ads7846: ads7846@1 {
+				compatible = "ti,ads7846";
+				reg = <1>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&ads7846_pins>;
+
+				spi-max-frequency = <2000000>;
+				interrupts = <255 2>; /* high-to-low edge triggered */
+				interrupt-parent = <&gpio>;
+				pendown-gpio = <&gpio 255 0>;
+
+				/* driver defaults */
+				ti,x-min = /bits/ 16 <0>;
+				ti,y-min = /bits/ 16 <0>;
+				ti,x-max = /bits/ 16 <0x0FFF>;
+				ti,y-max = /bits/ 16 <0x0FFF>;
+				ti,pressure-min = /bits/ 16 <0>;
+				ti,pressure-max = /bits/ 16 <0xFFFF>;
+				ti,x-plate-ohms = /bits/ 16 <400>;
+			};
+		};
+	};
+	__overrides__ {
+		cs =     <&ads7846>,"reg:0";
+		speed =  <&ads7846>,"spi-max-frequency:0";
+		penirq = <&ads7846_pins>,"brcm,pins:0", /* REQUIRED */
+			 <&ads7846>,"interrupts:0",
+			 <&ads7846>,"pendown-gpio:4";
+		penirq_pull = <&ads7846_pins>,"brcm,pull:0";
+		swapxy = <&ads7846>,"ti,swap-xy?";
+		xmin =   <&ads7846>,"ti,x-min;0";
+		ymin =   <&ads7846>,"ti,y-min;0";
+		xmax =   <&ads7846>,"ti,x-max;0";
+		ymax =   <&ads7846>,"ti,y-max;0";
+		pmin =   <&ads7846>,"ti,pressure-min;0";
+		pmax =   <&ads7846>,"ti,pressure-max;0";
+		xohms =  <&ads7846>,"ti,x-plate-ohms;0";
+	};
+};

arch/arm/boot/dts/overlays/at86rf233-overlay.dts

@@ -0,0 +1,54 @@
+/dts-v1/;
+/plugin/;
+
+/* Overlay for Atmel AT86RF233 IEEE 802.15.4 WPAN transceiver on spi0.0 */
+
+/ {
+	compatible = "brcm,bcm2835", "brcm,bcm2836", "brcm,bcm2708", "brcm,bcm2709";
+
+	fragment@0 {
+		target = <&spi0>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "okay";
+
+			spidev@0{
+				status = "disabled";
+			};
+
+			lowpan0: at86rf233@0 {
+				compatible = "atmel,at86rf233";
+				reg = <0>;
+				interrupt-parent = <&gpio>;
+				interrupts = <23 4>; /* active high */
+				reset-gpio = <&gpio 24 1>;
+				sleep-gpio = <&gpio 25 1>;
+				spi-max-frequency = <3000000>;
+				xtal-trim = /bits/ 8 <0xf>;
+			};
+		};
+	};
+
+	fragment@1 {
+		target = <&gpio>;
+		__overlay__ {
+			lowpan0_pins: lowpan0_pins {
+				brcm,pins = <23 24 25>;
+				brcm,function = <0 1 1>; /* in out out */
+			};
+		};
+	};
+
+	__overrides__ {
+		interrupt = <&lowpan0>, "interrupts:0",
+			<&lowpan0_pins>, "brcm,pins:0";
+		reset     = <&lowpan0>, "reset-gpio:4",
+			<&lowpan0_pins>, "brcm,pins:4";
+		sleep     = <&lowpan0>, "sleep-gpio:4",
+			<&lowpan0_pins>, "brcm,pins:8";
+		speed     = <&lowpan0>, "spi-max-frequency:0";
+		trim      = <&lowpan0>, "xtal-trim.0";
+	};
+};

arch/arm/boot/dts/overlays/bmp085_i2c-sensor-overlay.dts

@@ -0,0 +1,23 @@
+// Definitions for BMP085/BMP180 digital barometric pressure and temperature sensors from Bosch Sensortec
+/dts-v1/;
+/plugin/;
+
+/ {
+        compatible = "brcm,bcm2708";
+
+        fragment@0 {
+                target = <&i2c_arm>;
+                __overlay__ {
+                        #address-cells = <1>;
+                        #size-cells = <0>;
+                        status = "okay";
+
+                        bmp085@77 {
+                                compatible = "bosch,bmp085";
+                                reg = <0x77>;
+                                default-oversampling = <3>;
+                                status = "okay";
+                        };
+                };
+        };
+};

arch/arm/boot/dts/overlays/dht11-overlay.dts

@@ -0,0 +1,39 @@
+/*
+ * Overlay for the DHT11/21/22 humidity/temperature sensor modules.
+ */
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target-path = "/";
+		__overlay__ {
+
+			dht11: dht11@0 {
+				compatible = "dht11";
+				pinctrl-names = "default";
+				pinctrl-0 = <&dht11_pins>;
+				gpios = <&gpio 4 0>;
+				status = "okay";
+			};
+		};
+	};
+
+	fragment@1 {
+		target = <&gpio>;
+		__overlay__ {
+			dht11_pins: dht11_pins {
+				brcm,pins = <4>;
+				brcm,function = <0>; // in
+				brcm,pull = <0>; // off
+			};
+		};
+	};
+
+	__overrides__ {
+		gpiopin = <&dht11_pins>,"brcm,pins:0",
+			<&dht11>,"gpios:4";
+	};
+};

arch/arm/boot/dts/overlays/enc28j60-overlay.dts

@@ -0,0 +1,50 @@
+// Overlay for the Microchip ENC28J60 Ethernet Controller
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&spi0>;
+		__overlay__ {
+			/* needed to avoid dtc warning */
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "okay";
+
+			spidev@0{
+				status = "disabled";
+			};
+
+			eth1: enc28j60@0{
+				compatible = "microchip,enc28j60";
+				reg = <0>; /* CE0 */
+				pinctrl-names = "default";
+				pinctrl-0 = <&eth1_pins>;
+				interrupt-parent = <&gpio>;
+				interrupts = <25 0x2>; /* falling edge */
+				spi-max-frequency = <12000000>;
+				status = "okay";
+			};
+		};
+	};
+
+	fragment@1 {
+		target = <&gpio>;
+		__overlay__ {
+			eth1_pins: eth1_pins {
+				brcm,pins = <25>;
+				brcm,function = <0>; /* in */
+				brcm,pull = <0>; /* none */
+			};
+		};
+	};
+
+	__overrides__ {
+		int_pin = <&eth1>, "interrupts:0",
+		          <&eth1_pins>, "brcm,pins:0";
+		speed   = <&eth1>, "spi-max-frequency:0";
+	};
+};

arch/arm/boot/dts/overlays/gpio-ir-overlay.dts

@@ -0,0 +1,45 @@
+// Definitions for ir-gpio module
+/dts-v1/;
+/plugin/;
+
+/ {
+        compatible = "brcm,bcm2708";
+
+        fragment@0 {
+                target-path = "/";
+                __overlay__ {
+                        gpio_ir: ir-receiver {
+                                compatible = "gpio-ir-receiver";
+
+                                // pin number, high or low
+                                gpios = <&gpio 18 1>;
+
+                                // parameter for keymap name
+                                linux,rc-map-name = "rc-rc6-mce";
+
+                                status = "okay";
+                        };
+                };
+        };
+
+        fragment@1 {
+                target = <&gpio>;
+                __overlay__ {
+                        gpio_ir_pins: gpio_ir_pins {
+                                brcm,pins = <18>;                       // pin 18
+                                brcm,function = <0>;                    // in
+                                brcm,pull = <1>;                        // down
+                        };
+                };
+        };
+
+        __overrides__ {
+                // parameters
+                gpio_pin =      <&gpio_ir>,"gpios:4",
+                                        <&gpio_ir_pins>,"brcm,pins:0",
+                                        <&gpio_ir_pins>,"brcm,pull:0";  // pin number
+                gpio_pull = <&gpio_ir_pins>,"brcm,pull:0";              // pull-up/down state
+
+                rc-map-name = <&gpio_ir>,"linux,rc-map-name";           // default rc map
+        };
+};

arch/arm/boot/dts/overlays/gpio-poweroff-overlay.dts

@@ -0,0 +1,34 @@
+// Definitions for gpio-poweroff module
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target-path = "/";
+		__overlay__ {
+			power_ctrl: power_ctrl {
+				compatible = "gpio-poweroff";
+				gpios = <&gpio 26 0>;
+				force;
+			};
+		};
+	};
+
+	fragment@1 {
+		target = <&gpio>;
+		__overlay__ {
+			power_ctrl_pins: power_ctrl_pins {
+				brcm,pins = <26>;
+				brcm,function = <1>; // out
+			};
+		};
+	};
+
+	__overrides__ {
+		gpiopin =       <&power_ctrl>,"gpios:4",
+				<&power_ctrl_pins>,"brcm,pins:0";
+		active_low =    <&power_ctrl>,"gpios:8";
+	};
+};

arch/arm/boot/dts/overlays/hifiberry-amp-overlay.dts

@@ -0,0 +1,39 @@
+// Definitions for HiFiBerry Amp/Amp+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&sound>;
+		__overlay__ {
+			compatible = "hifiberry,hifiberry-amp";
+			i2s-controller = <&i2s>;
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&i2s>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@2 {
+		target = <&i2c1>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			tas5713@1b {
+				#sound-dai-cells = <0>;
+				compatible = "ti,tas5713";
+				reg = <0x1b>;
+				status = "okay";
+			};
+		};
+	};
+};

arch/arm/boot/dts/overlays/hifiberry-dac-overlay.dts

@@ -0,0 +1,34 @@
+// Definitions for HiFiBerry DAC
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&sound>;
+		__overlay__ {
+			compatible = "hifiberry,hifiberry-dac";
+			i2s-controller = <&i2s>;
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&i2s>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@2 {
+		target-path = "/";
+		__overlay__ {
+			pcm5102a-codec {
+				#sound-dai-cells = <0>;
+				compatible = "ti,pcm5102a";
+				status = "okay";
+			};
+		};
+	};
+};

arch/arm/boot/dts/overlays/hifiberry-dacplus-overlay.dts

@@ -0,0 +1,54 @@
+// Definitions for HiFiBerry DAC+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target-path = "/clocks";
+		__overlay__ {
+			dacpro_osc: dacpro_osc {
+				compatible = "hifiberry,dacpro-clk";
+				#clock-cells = <0>;
+			};
+		};
+	};
+
+	fragment@1 {
+		target = <&sound>;
+		frag1: __overlay__ {
+			compatible = "hifiberry,hifiberry-dacplus";
+			i2s-controller = <&i2s>;
+			status = "okay";
+		};
+	};
+
+	fragment@2 {
+		target = <&i2s>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@3 {
+		target = <&i2c1>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			pcm5122@4d {
+				#sound-dai-cells = <0>;
+				compatible = "ti,pcm5122";
+				reg = <0x4d>;
+				clocks = <&dacpro_osc>;
+				status = "okay";
+			};
+		};
+	};
+
+	__overrides__ {
+		24db_digital_gain = <&frag1>,"hifiberry,24db_digital_gain?";
+	};
+};

arch/arm/boot/dts/overlays/hifiberry-digi-overlay.dts

@@ -0,0 +1,39 @@
+// Definitions for HiFiBerry Digi
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&sound>;
+		__overlay__ {
+			compatible = "hifiberry,hifiberry-digi";
+			i2s-controller = <&i2s>;
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&i2s>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@2 {
+		target = <&i2c1>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			wm8804@3b {
+				#sound-dai-cells = <0>;
+				compatible = "wlf,wm8804";
+				reg = <0x3b>;
+				status = "okay";
+			};
+		};
+	};
+};

arch/arm/boot/dts/overlays/hy28a-overlay.dts

@@ -0,0 +1,87 @@
+/*
+ * Device Tree overlay for HY28A display
+ *
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
+
+	fragment@0 {
+		target = <&spi0>;
+		__overlay__ {
+			status = "okay";
+
+			spidev@0{
+				status = "disabled";
+			};
+
+			spidev@1{
+				status = "disabled";
+			};
+		};
+	};
+
+	fragment@1 {
+		target = <&gpio>;
+		__overlay__ {
+			hy28a_pins: hy28a_pins {
+				brcm,pins = <17 25 18>;
+				brcm,function = <0 1 1>; /* in out out */
+			};
+		};
+	};
+
+	fragment@2 {
+		target = <&spi0>;
+		__overlay__ {
+			/* needed to avoid dtc warning */
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			hy28a: hy28a@0{
+				compatible = "ilitek,ili9320";
+				reg = <0>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&hy28a_pins>;
+
+				spi-max-frequency = <32000000>;
+				spi-cpol;
+				spi-cpha;
+				rotate = <270>;
+				bgr;
+				fps = <50>;
+				buswidth = <8>;
+				startbyte = <0x70>;
+				reset-gpios = <&gpio 25 0>;
+				led-gpios = <&gpio 18 1>;
+				debug = <0>;
+			};
+
+			hy28a_ts: hy28a-ts@1 {
+				compatible = "ti,ads7846";
+				reg = <1>;
+
+				spi-max-frequency = <2000000>;
+				interrupts = <17 2>; /* high-to-low edge triggered */
+				interrupt-parent = <&gpio>;
+				pendown-gpio = <&gpio 17 0>;
+				ti,x-plate-ohms = /bits/ 16 <100>;
+				ti,pressure-max = /bits/ 16 <255>;
+			};
+		};
+	};
+	__overrides__ {
+		speed =		<&hy28a>,"spi-max-frequency:0";
+		rotate =	<&hy28a>,"rotate:0";
+		fps =		<&hy28a>,"fps:0";
+		debug =		<&hy28a>,"debug:0";
+		xohms =		<&hy28a_ts>,"ti,x-plate-ohms;0";
+		resetgpio =	<&hy28a>,"reset-gpios:4",
+				<&hy28a_pins>, "brcm,pins:1";
+		ledgpio =	<&hy28a>,"led-gpios:4",
+				<&hy28a_pins>, "brcm,pins:2";
+	};
+};

arch/arm/boot/dts/overlays/hy28b-overlay.dts

@@ -0,0 +1,142 @@
+/*
+ * Device Tree overlay for HY28b display shield by Texy
+ *
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
+
+	fragment@0 {
+		target = <&spi0>;
+		__overlay__ {
+			status = "okay";
+
+			spidev@0{
+				status = "disabled";
+			};
+
+			spidev@1{
+				status = "disabled";
+			};
+		};
+	};
+
+	fragment@1 {
+		target = <&gpio>;
+		__overlay__ {
+			hy28b_pins: hy28b_pins {
+				brcm,pins = <17 25 18>;
+				brcm,function = <0 1 1>; /* in out out */
+			};
+		};
+	};
+
+	fragment@2 {
+		target = <&spi0>;
+		__overlay__ {
+			/* needed to avoid dtc warning */
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			hy28b: hy28b@0{
+				compatible = "ilitek,ili9325";
+				reg = <0>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&hy28b_pins>;
+
+				spi-max-frequency = <48000000>;
+				spi-cpol;
+				spi-cpha;
+				rotate = <270>;
+				bgr;
+				fps = <50>;
+				buswidth = <8>;
+				startbyte = <0x70>;
+				reset-gpios = <&gpio 25 0>;
+				led-gpios = <&gpio 18 1>;
+
+				gamma = "04 1F 4 7 7 0 7 7 6 0\n0F 00 1 7 4 0 0 0 6 7";
+
+				init = <0x10000e7 0x0010
+					0x1000000 0x0001
+					0x1000001 0x0100
+					0x1000002 0x0700
+				        0x1000003 0x1030
+					0x1000004 0x0000
+					0x1000008 0x0207
+					0x1000009 0x0000
+				        0x100000a 0x0000
+					0x100000c 0x0001
+					0x100000d 0x0000
+					0x100000f 0x0000
+				        0x1000010 0x0000
+					0x1000011 0x0007
+					0x1000012 0x0000
+					0x1000013 0x0000
+				        0x2000032
+					0x1000010 0x1590
+					0x1000011 0x0227
+				        0x2000032
+					0x1000012 0x009c
+				        0x2000032
+				        0x1000013 0x1900
+					0x1000029 0x0023
+					0x100002b 0x000e
+				        0x2000032
+				        0x1000020 0x0000
+					0x1000021 0x0000
+				        0x2000032
+					0x1000050 0x0000
+				        0x1000051 0x00ef
+					0x1000052 0x0000
+					0x1000053 0x013f
+					0x1000060 0xa700
+				        0x1000061 0x0001
+					0x100006a 0x0000
+					0x1000080 0x0000
+					0x1000081 0x0000
+				        0x1000082 0x0000
+					0x1000083 0x0000
+					0x1000084 0x0000
+					0x1000085 0x0000
+				        0x1000090 0x0010
+					0x1000092 0x0000
+					0x1000093 0x0003
+					0x1000095 0x0110
+				        0x1000097 0x0000
+					0x1000098 0x0000
+					0x1000007 0x0133
+					0x1000020 0x0000
+				        0x1000021 0x0000
+				        0x2000064>;
+				debug = <0>;
+			};
+
+			hy28b_ts: hy28b-ts@1 {
+				compatible = "ti,ads7846";
+				reg = <1>;
+
+				spi-max-frequency = <2000000>;
+				interrupts = <17 2>; /* high-to-low edge triggered */
+				interrupt-parent = <&gpio>;
+				pendown-gpio = <&gpio 17 0>;
+				ti,x-plate-ohms = /bits/ 16 <100>;
+				ti,pressure-max = /bits/ 16 <255>;
+			};
+		};
+	};
+	__overrides__ {
+		speed = 	<&hy28b>,"spi-max-frequency:0";
+		rotate = 	<&hy28b>,"rotate:0";
+		fps = 		<&hy28b>,"fps:0";
+		debug = 	<&hy28b>,"debug:0";
+		xohms =		<&hy28b_ts>,"ti,x-plate-ohms;0";
+		resetgpio =	<&hy28b>,"reset-gpios:4",
+				<&hy28b_pins>, "brcm,pins:1";
+		ledgpio =	<&hy28b>,"led-gpios:4",
+				<&hy28b_pins>, "brcm,pins:2";
+	};
+};

arch/arm/boot/dts/overlays/i2c-gpio-overlay.dts

@@ -0,0 +1,28 @@
+// Overlay for i2c_gpio bitbanging host bus.
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target-path = "/";
+		__overlay__ {
+			i2c_gpio: i2c@0 {
+				compatible = "i2c-gpio";
+				gpios = <&gpio 23 0 /* sda */
+					 &gpio 24 0 /* scl */
+					>;
+				i2c-gpio,delay-us = <2>;        /* ~100 kHz */
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+	__overrides__ {
+		i2c_gpio_sda = <&i2c_gpio>,"gpios:4";
+		i2c_gpio_scl = <&i2c_gpio>,"gpios:16";
+		i2c_gpio_delay_us = <&i2c_gpio>,"i2c-gpio,delay-us:0";
+	};
+};
+

arch/arm/boot/dts/overlays/i2c-rtc-overlay.dts

@@ -0,0 +1,55 @@
+// Definitions for several I2C based Real Time Clocks
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&i2c_arm>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			ds1307: ds1307@68 {
+				compatible = "maxim,ds1307";
+				reg = <0x68>;
+				status = "disable";
+			};
+			mcp7941x: mcp7941x@6f {
+				compatible = "microchip,mcp7941x";
+				reg = <0x6f>;
+				status = "disable";
+			};
+			ds3231: ds3231@68 {
+				compatible = "maxim,ds3231";
+				reg = <0x68>;
+				status = "disable";
+			};
+			pcf2127: pcf2127@51 {
+				compatible = "nxp,pcf2127";
+				reg = <0x51>;
+				status = "disable";
+			};
+			pcf8523: pcf8523@68 {
+				compatible = "nxp,pcf8523";
+				reg = <0x68>;
+				status = "disable";
+			};
+			pcf8563: pcf8563@51 {
+				compatible = "nxp,pcf8563";
+				reg = <0x51>;
+				status = "disable";
+			};
+		};
+	};
+	__overrides__ {
+		ds1307 = <&ds1307>,"status";
+		ds3231 = <&ds3231>,"status";
+		mcp7941x = <&mcp7941x>,"status";
+		pcf2127 = <&pcf2127>,"status";
+		pcf8523 = <&pcf8523>,"status";
+		pcf8563 = <&pcf8563>,"status";
+	};
+};

arch/arm/boot/dts/overlays/i2c0-bcm2708-overlay.dts

@@ -0,0 +1,36 @@
+/*
+ * Device tree overlay for i2c_bcm2708, i2c0 bus
+ *
+ * Compile:
+ * dtc -@ -I dts -O dtb -o i2c0-bcm2708-overlay.dtb i2c0-bcm2708-overlay.dts
+ */
+
+/dts-v1/;
+/plugin/;
+
+/{
+   compatible = "brcm,bcm2708";
+
+   fragment@0 {
+      target = <&i2c0>;
+      __overlay__ {
+         pinctrl-0 = <&i2c0_pins>;
+         status = "okay";
+      };
+   };
+
+   fragment@1 {
+      target = <&gpio>;
+      __overlay__ {
+         i2c0_pins: i2c0 {
+            brcm,pins = <0 1>;
+            brcm,function = <4>; /* alt0 */
+         };
+      };
+   };
+
+   __overrides__ {
+      sda0_pin = <&i2c0_pins>,"brcm,pins:0";
+      scl0_pin = <&i2c0_pins>,"brcm,pins:4";
+   };
+};

arch/arm/boot/dts/overlays/i2c1-bcm2708-overlay.dts

@@ -0,0 +1,37 @@
+/*
+ * Device tree overlay for i2c_bcm2708, i2c1 bus
+ *
+ * Compile:
+ * dtc -@ -I dts -O dtb -o i2c1-bcm2708-overlay.dtb i2c1-bcm2708-overlay.dts
+ */
+
+/dts-v1/;
+/plugin/;
+
+/{
+   compatible = "brcm,bcm2708";
+
+   fragment@0 {
+      target = <&i2c1>;
+      __overlay__ {
+         pinctrl-0 = <&i2c1_pins>;
+         status = "okay";
+      };
+   };
+
+   fragment@1 {
+      target = <&gpio>;
+      __overlay__ {
+         i2c1_pins: i2c1 {
+            brcm,pins = <2 3>;
+            brcm,function = <4>; /* alt0 */
+         };
+      };
+   };
+
+   __overrides__ {
+      sda1_pin = <&i2c1_pins>,"brcm,pins:0";
+      scl1_pin = <&i2c1_pins>,"brcm,pins:4";
+      pin_func = <&i2c1_pins>,"brcm,function:0";
+   };
+};

arch/arm/boot/dts/overlays/i2s-mmap-overlay.dts

@@ -0,0 +1,13 @@
+/dts-v1/;
+/plugin/;
+
+/{
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&i2s>;
+		__overlay__ {
+			brcm,enable-mmap;
+		};
+	};
+};

arch/arm/boot/dts/overlays/iqaudio-dac-overlay.dts

@@ -0,0 +1,39 @@
+// Definitions for IQaudIO DAC
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&sound>;
+		__overlay__ {
+			compatible = "iqaudio,iqaudio-dac";
+			i2s-controller = <&i2s>;
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&i2s>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@2 {
+		target = <&i2c1>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			pcm5122@4c {
+				#sound-dai-cells = <0>;
+				compatible = "ti,pcm5122";
+				reg = <0x4c>;
+				status = "okay";
+			};
+		};
+	};
+};

arch/arm/boot/dts/overlays/iqaudio-dacplus-overlay.dts

@@ -0,0 +1,43 @@
+// Definitions for IQaudIO DAC+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&sound>;
+		frag0: __overlay__ {
+			compatible = "iqaudio,iqaudio-dac";
+			i2s-controller = <&i2s>;
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&i2s>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@2 {
+		target = <&i2c1>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			pcm5122@4c {
+				#sound-dai-cells = <0>;
+				compatible = "ti,pcm5122";
+				reg = <0x4c>;
+				status = "okay";
+			};
+		};
+	};
+
+	__overrides__ {
+		24db_digital_gain = <&frag0>,"iqaudio,24db_digital_gain?";
+	};
+};

arch/arm/boot/dts/overlays/lirc-rpi-overlay.dts

@@ -0,0 +1,57 @@
+// Definitions for lirc-rpi module
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target-path = "/";
+		__overlay__ {
+			lirc_rpi: lirc_rpi {
+				compatible = "rpi,lirc-rpi";
+				pinctrl-names = "default";
+				pinctrl-0 = <&lirc_pins>;
+				status = "okay";
+
+				// Override autodetection of IR receiver circuit
+				// (0 = active high, 1 = active low, -1 = no override )
+				rpi,sense = <0xffffffff>;
+
+				// Software carrier
+				// (0 = off, 1 = on)
+				rpi,softcarrier = <1>;
+
+				// Invert output
+				// (0 = off, 1 = on)
+				rpi,invert = <0>;
+
+				// Enable debugging messages
+				// (0 = off, 1 = on)
+				rpi,debug = <0>;
+			};
+		};
+	};
+
+	fragment@1 {
+		target = <&gpio>;
+		__overlay__ {
+			lirc_pins: lirc_pins {
+				brcm,pins = <17 18>;
+				brcm,function = <1 0>; // out in
+				brcm,pull = <0 1>; // off down
+			};
+		};
+	};
+
+	__overrides__ {
+		gpio_out_pin =  <&lirc_pins>,"brcm,pins:0";
+		gpio_in_pin =   <&lirc_pins>,"brcm,pins:4";
+		gpio_in_pull =  <&lirc_pins>,"brcm,pull:4";
+
+		sense =         <&lirc_rpi>,"rpi,sense:0";
+		softcarrier =   <&lirc_rpi>,"rpi,softcarrier:0";
+		invert =        <&lirc_rpi>,"rpi,invert:0";
+		debug =         <&lirc_rpi>,"rpi,debug:0";
+	};
+};

arch/arm/boot/dts/overlays/mcp2515-can0-overlay.dts

@@ -0,0 +1,69 @@
+/*
+ * Device tree overlay for mcp251x/can0 on spi0.0
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+    compatible = "brcm,bcm2835", "brcm,bcm2836", "brcm,bcm2708", "brcm,bcm2709";
+    /* disable spi-dev for spi0.0 */
+    fragment@0 {
+        target = <&spi0>;
+        __overlay__ {
+            status = "okay";
+            spidev@0{
+                status = "disabled";
+            };
+        };
+    };
+
+    /* the interrupt pin of the can-controller */
+    fragment@1 {
+        target = <&gpio>;
+        __overlay__ {
+            can0_pins: can0_pins {
+                brcm,pins = <25>;
+                brcm,function = <0>; /* input */
+            };
+        };
+    };
+
+    /* the clock/oscillator of the can-controller */
+    fragment@2 {
+        target-path = "/clocks";
+        __overlay__ {
+            /* external oscillator of mcp2515 on SPI0.0 */
+            can0_osc: can0_osc {
+                compatible = "fixed-clock";
+                #clock-cells = <0>;
+                clock-frequency  = <16000000>;
+            };
+        };
+    };
+
+    /* the spi config of the can-controller itself binding everything together */
+    fragment@3 {
+        target = <&spi0>;
+        __overlay__ {
+            /* needed to avoid dtc warning */
+            #address-cells = <1>;
+            #size-cells = <0>;
+            can0: mcp2515@0 {
+                reg = <0>;
+                compatible = "microchip,mcp2515";
+                pinctrl-names = "default";
+                pinctrl-0 = <&can0_pins>;
+                spi-max-frequency = <10000000>;
+                interrupt-parent = <&gpio>;
+                interrupts = <25 0x2>;
+                clocks = <&can0_osc>;
+            };
+        };
+    };
+    __overrides__ {
+        oscillator = <&can0_osc>,"clock-frequency:0";
+        spimaxfrequency = <&can0>,"spi-max-frequency:0";
+        interrupt = <&can0_pins>,"brcm,pins:0",<&can0>,"interrupts:0";
+    };
+};

arch/arm/boot/dts/overlays/mcp2515-can1-overlay.dts

@@ -0,0 +1,69 @@
+/*
+ * Device tree overlay for mcp251x/can1 on spi0.1 edited by petit_miner
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+    compatible = "brcm,bcm2835", "brcm,bcm2836", "brcm,bcm2708", "brcm,bcm2709";
+    /* disable spi-dev for spi0.1 */
+    fragment@0 {
+        target = <&spi0>;
+        __overlay__ {
+            status = "okay";
+            spidev@1{
+                status = "disabled";
+            };
+        };
+    };
+
+    /* the interrupt pin of the can-controller */
+    fragment@1 {
+        target = <&gpio>;
+        __overlay__ {
+            can1_pins: can1_pins {
+                brcm,pins = <25>;
+                brcm,function = <0>; /* input */
+            };
+        };
+    };
+
+    /* the clock/oscillator of the can-controller */
+    fragment@2 {
+        target-path = "/clocks";
+        __overlay__ {
+            /* external oscillator of mcp2515 on spi0.1 */
+            can1_osc: can1_osc {
+                compatible = "fixed-clock";
+                #clock-cells = <0>;
+                clock-frequency  = <16000000>;
+            };
+        };
+    };
+
+    /* the spi config of the can-controller itself binding everything together */
+    fragment@3 {
+        target = <&spi0>;
+        __overlay__ {
+            /* needed to avoid dtc warning */
+            #address-cells = <1>;
+            #size-cells = <0>;
+            can1: mcp2515@1 {
+                reg = <1>;
+                compatible = "microchip,mcp2515";
+                pinctrl-names = "default";
+                pinctrl-0 = <&can1_pins>;
+                spi-max-frequency = <10000000>;
+                interrupt-parent = <&gpio>;
+                interrupts = <25 0x2>;
+                clocks = <&can1_osc>;
+            };
+        };
+    };
+    __overrides__ {
+        oscillator = <&can1_osc>,"clock-frequency:0";
+        spimaxfrequency = <&can1>,"spi-max-frequency:0";
+        interrupt = <&can1_pins>,"brcm,pins:0",<&can1>,"interrupts:0";
+    };
+};

arch/arm/boot/dts/overlays/mmc-overlay.dts

@@ -0,0 +1,38 @@
+/dts-v1/;
+/plugin/;
+
+/{
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&mmc>;
+		frag0: __overlay__ {
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc_pins>;
+			bus-width = <4>;
+			brcm,overclock-50 = <0>;
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&gpio>;
+		__overlay__ {
+			mmc_pins: mmc_pins {
+				brcm,pins = <48 49 50 51 52 53>;
+				brcm,function = <7>; /* alt3 */
+			};
+		};
+	};
+
+	fragment@2 {
+		target = <&sdhost>;
+		__overlay__ {
+			status = "disabled";
+		};
+	};
+
+	__overrides__ {
+		overclock_50     = <&frag0>,"brcm,overclock-50:0";
+	};
+};

arch/arm/boot/dts/overlays/mz61581-overlay.dts

@@ -0,0 +1,111 @@
+/*
+ * Device Tree overlay for MZ61581-PI-EXT 2014.12.28 by Tontec
+ *
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
+
+	fragment@0 {
+		target = <&spi0>;
+		__overlay__ {
+			status = "okay";
+
+			spidev@0{
+				status = "disabled";
+			};
+
+			spidev@1{
+				status = "disabled";
+			};
+		};
+	};
+
+	fragment@1 {
+		target = <&gpio>;
+		__overlay__ {
+			mz61581_pins: mz61581_pins {
+				brcm,pins = <4 15 18 25>;
+				brcm,function = <0 1 1 1>; /* in out out out */
+			};
+		};
+	};
+
+	fragment@2 {
+		target = <&spi0>;
+		__overlay__ {
+			/* needed to avoid dtc warning */
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			mz61581: mz61581@0{
+				compatible = "samsung,s6d02a1";
+				reg = <0>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&mz61581_pins>;
+
+				spi-max-frequency = <128000000>;
+				spi-cpol;
+				spi-cpha;
+
+				width = <320>;
+				height = <480>;
+				rotate = <270>;
+				bgr;
+				fps = <30>;
+				buswidth = <8>;
+				txbuflen = <32768>;
+
+				reset-gpios = <&gpio 15 0>;
+				dc-gpios = <&gpio 25 0>;
+				led-gpios = <&gpio 18 0>;
+
+				init = <0x10000b0 00
+					0x1000011
+					0x20000ff
+					0x10000b3 0x02 0x00 0x00 0x00
+					0x10000c0 0x13 0x3b 0x00 0x02 0x00 0x01 0x00 0x43
+					0x10000c1 0x08 0x16 0x08 0x08
+					0x10000c4 0x11 0x07 0x03 0x03
+					0x10000c6 0x00
+					0x10000c8 0x03 0x03 0x13 0x5c 0x03 0x07 0x14 0x08 0x00 0x21 0x08 0x14 0x07 0x53 0x0c 0x13 0x03 0x03 0x21 0x00
+					0x1000035 0x00
+					0x1000036 0xa0
+					0x100003a 0x55
+					0x1000044 0x00 0x01
+					0x10000d0 0x07 0x07 0x1d 0x03
+					0x10000d1 0x03 0x30 0x10
+					0x10000d2 0x03 0x14 0x04
+					0x1000029
+					0x100002c>;
+
+				/* This is a workaround to make sure the init sequence slows down and doesn't fail */
+				debug = <3>;
+			};
+
+			mz61581_ts: mz61581_ts@1 {
+				compatible = "ti,ads7846";
+				reg = <1>;
+
+				spi-max-frequency = <2000000>;
+				interrupts = <4 2>; /* high-to-low edge triggered */
+				interrupt-parent = <&gpio>;
+				pendown-gpio = <&gpio 4 0>;
+
+				ti,x-plate-ohms = /bits/ 16 <60>;
+				ti,pressure-max = /bits/ 16 <255>;
+			};
+		};
+	};
+	__overrides__ {
+		speed =   <&mz61581>, "spi-max-frequency:0";
+		rotate =  <&mz61581>, "rotate:0";
+		fps =     <&mz61581>, "fps:0";
+		txbuflen = <&mz61581>, "txbuflen:0";
+		debug =   <&mz61581>, "debug:0";
+		xohms =   <&mz61581_ts>,"ti,x-plate-ohms;0";
+	};
+};

arch/arm/boot/dts/overlays/pi3-disable-bt-overlay.dts

@@ -0,0 +1,48 @@
+/dts-v1/;
+/plugin/;
+
+/* Disable Bluetooth and restore UART0/ttyAMA0 over GPIOs 14 & 15.
+   To disable the systemd service that initialises the modem so it doesn't use
+   the UART:
+
+       sudo systemctl disable hciuart
+*/
+
+/{
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&uart1>;
+		__overlay__ {
+			status = "disabled";
+		};
+	};
+
+	fragment@1 {
+		target = <&uart0>;
+		__overlay__ {
+			pinctrl-names = "default";
+			pinctrl-0 = <&uart0_pins>;
+			status = "okay";
+		};
+	};
+
+	fragment@2 {
+		target = <&gpio>;
+		__overlay__ {
+			uart0_pins: uart0_pins {
+				brcm,pins = <14 15>;
+				brcm,function = <4>; /* alt0 */
+				brcm,pull = <0 2>;
+			};
+		};
+	};
+
+	fragment@3 {
+		target-path = "/aliases";
+		__overlay__ {
+			serial0 = "/soc/uart@7e201000";
+			serial1 = "/soc/uart@7e215040";
+		};
+	};
+};

arch/arm/boot/dts/overlays/pi3-miniuart-bt-overlay.dts

@@ -0,0 +1,61 @@
+/dts-v1/;
+/plugin/;
+
+/* Switch Pi3 Bluetooth function to use the mini-UART (ttyS0) and restore
+   UART0/ttyAMA0 over GPIOs 14 & 15. Note that this may reduce the maximum
+   usable baudrate.
+
+   It is also necessary to edit /lib/systemd/system/hciuart.server and
+   replace ttyAMA0 with ttyS0.
+
+   If cmdline.txt uses the alias serial0 to refer to the user-accessable port
+   then the firmware will replace with the appropriate port whether or not
+   this overlay is used.
+*/
+
+/{
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&uart0>;
+		__overlay__ {
+			pinctrl-names = "default";
+			pinctrl-0 = <&uart0_pins>;
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&uart1>;
+		__overlay__ {
+			pinctrl-names = "default";
+			pinctrl-0 = <&uart1_pins>;
+			status = "okay";
+		};
+	};
+
+	fragment@2 {
+		target = <&gpio>;
+		__overlay__ {
+			uart0_pins: uart0_pins {
+				brcm,pins = <14 15>;
+				brcm,function = <4>; /* alt0 */
+				brcm,pull = <0 2>;
+			};
+
+			uart1_pins: uart1_pins {
+				brcm,pins = <32 33>;
+				brcm,function = <2>; /* alt5=UART1 */
+				brcm,pull = <0 0>;
+			};
+		};
+	};
+
+	fragment@3 {
+		target-path = "/aliases";
+		__overlay__ {
+			serial0 = "/soc/uart@7e201000";
+			serial1 = "/soc/uart@7e215040";
+		};
+	};
+};

arch/arm/boot/dts/overlays/piscreen-overlay.dts

@@ -0,0 +1,96 @@
+/*
+ * Device Tree overlay for PiScreen 3.5" display shield by Ozzmaker
+ *
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
+
+	fragment@0 {
+		target = <&spi0>;
+		__overlay__ {
+			status = "okay";
+
+			spidev@0{
+				status = "disabled";
+			};
+
+			spidev@1{
+				status = "disabled";
+			};
+		};
+	};
+
+	fragment@1 {
+		target = <&gpio>;
+		__overlay__ {
+			piscreen_pins: piscreen_pins {
+				brcm,pins = <17 25 24 22>;
+				brcm,function = <0 1 1 1>; /* in out out out */
+			};
+		};
+	};
+
+	fragment@2 {
+		target = <&spi0>;
+		__overlay__ {
+			/* needed to avoid dtc warning */
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			piscreen: piscreen@0{
+				compatible = "ilitek,ili9486";
+				reg = <0>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&piscreen_pins>;
+
+				spi-max-frequency = <24000000>;
+				rotate = <270>;
+				bgr;
+				fps = <30>;
+				buswidth = <8>;
+				regwidth = <16>;
+				reset-gpios = <&gpio 25 0>;
+				dc-gpios = <&gpio 24 0>;
+				led-gpios = <&gpio 22 1>;
+				debug = <0>;
+
+				init = <0x10000b0 0x00
+				        0x1000011
+					0x20000ff
+					0x100003a 0x55
+					0x1000036 0x28
+					0x10000c2 0x44
+					0x10000c5 0x00 0x00 0x00 0x00
+					0x10000e0 0x0f 0x1f 0x1c 0x0c 0x0f 0x08 0x48 0x98 0x37 0x0a 0x13 0x04 0x11 0x0d 0x00
+					0x10000e1 0x0f 0x32 0x2e 0x0b 0x0d 0x05 0x47 0x75 0x37 0x06 0x10 0x03 0x24 0x20 0x00
+					0x10000e2 0x0f 0x32 0x2e 0x0b 0x0d 0x05 0x47 0x75 0x37 0x06 0x10 0x03 0x24 0x20 0x00
+					0x1000011
+					0x1000029>;
+			};
+
+			piscreen_ts: piscreen-ts@1 {
+				compatible = "ti,ads7846";
+				reg = <1>;
+
+				spi-max-frequency = <2000000>;
+				interrupts = <17 2>; /* high-to-low edge triggered */
+				interrupt-parent = <&gpio>;
+				pendown-gpio = <&gpio 17 0>;
+				ti,swap-xy;
+				ti,x-plate-ohms = /bits/ 16 <100>;
+				ti,pressure-max = /bits/ 16 <255>;
+			};
+		};
+	};
+	__overrides__ {
+		speed =		<&piscreen>,"spi-max-frequency:0";
+		rotate =	<&piscreen>,"rotate:0";
+		fps =		<&piscreen>,"fps:0";
+		debug =		<&piscreen>,"debug:0";
+		xohms =		<&piscreen_ts>,"ti,x-plate-ohms;0";
+	};
+};

arch/arm/boot/dts/overlays/piscreen2r-overlay.dts

@@ -0,0 +1,100 @@
+ /*
+ * Device Tree overlay for PiScreen2 3.5" TFT with resistive touch  by Ozzmaker.com
+ *
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
+
+	fragment@0 {
+		target = <&spi0>;
+		__overlay__ {
+			status = "okay";
+
+			spidev@0{
+				status = "disabled";
+			};
+
+			spidev@1{
+				status = "disabled";
+			};
+		};
+	};
+
+	fragment@1 {
+		target = <&gpio>;
+		__overlay__ {
+			piscreen2_pins: piscreen2_pins {
+				brcm,pins = <17 25 24 22>;
+				brcm,function = <0 1 1 1>; /* in out out out */
+			};
+		};
+	};
+
+	fragment@2 {
+		target = <&spi0>;
+		__overlay__ {
+			/* needed to avoid dtc warning */
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			piscreen2: piscreen2@0{
+				compatible = "ilitek,ili9486";
+				reg = <0>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&piscreen2_pins>;
+				bgr;
+				spi-max-frequency = <64000000>;
+				rotate = <90>;
+				fps = <30>;
+				buswidth = <8>;
+				regwidth = <16>;
+				txbuflen = <32768>;
+				reset-gpios = <&gpio 25 0>;
+				dc-gpios = <&gpio 24 0>;
+				led-gpios = <&gpio 22 1>;
+				debug = <0>;
+
+                                init = <0x10000b0 0x00
+                                        0x1000011
+                                        0x20000ff
+                                        0x100003a 0x55
+                                        0x1000036 0x28
+                                        0x10000c0 0x11 0x09
+                                        0x10000c1 0x41
+                                        0x10000c5 0x00 0x00 0x00 0x00
+                                        0x10000b6 0x00 0x02
+                                        0x10000f7 0xa9 0x51 0x2c 0x2
+                                        0x10000be 0x00 0x04
+                                        0x10000e9 0x00
+                                        0x1000011
+                                        0x1000029>;
+
+			};
+
+			piscreen2_ts: piscreen2-ts@1 {
+				compatible = "ti,ads7846";
+				reg = <1>;
+
+				spi-max-frequency = <2000000>;
+				interrupts = <17 2>; /* high-to-low edge triggered */
+				interrupt-parent = <&gpio>;
+				pendown-gpio = <&gpio 17 0>;
+				ti,swap-xy;
+				ti,x-plate-ohms = /bits/ 16 <100>;
+				ti,pressure-max = /bits/ 16 <255>;
+			};
+		};
+	};
+	__overrides__ {
+		speed =		<&piscreen2>,"spi-max-frequency:0";
+		rotate =	<&piscreen2>,"rotate:0";
+		fps =		<&piscreen2>,"fps:0";
+		debug =		<&piscreen2>,"debug:0";
+		xohms =		<&piscreen2_ts>,"ti,x-plate-ohms;0";
+	};
+};
+

arch/arm/boot/dts/overlays/pitft28-capacitive-overlay.dts

@@ -0,0 +1,88 @@
+/*
+ * Device Tree overlay for Adafruit PiTFT 2.8" capacitive touch screen
+ *
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+        compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
+
+        fragment@0 {
+                target = <&spi0>;
+                __overlay__ {
+                        status = "okay";
+
+                        spidev@0{
+                                status = "disabled";
+                        };
+                };
+        };
+
+        fragment@1 {
+                target = <&gpio>;
+                __overlay__ {
+                        pitft_pins: pitft_pins {
+                                brcm,pins = <24 25>;
+                                brcm,function = <0 1>; /* in out */
+                                brcm,pull = <2 0>; /* pullup none */
+                        };
+                };
+        };
+
+        fragment@2 {
+                target = <&spi0>;
+                __overlay__ {
+                        /* needed to avoid dtc warning */
+                        #address-cells = <1>;
+                        #size-cells = <0>;
+
+                        pitft: pitft@0{
+                                compatible = "ilitek,ili9340";
+                                reg = <0>;
+                                pinctrl-names = "default";
+                                pinctrl-0 = <&pitft_pins>;
+
+                                spi-max-frequency = <32000000>;
+                                rotate = <90>;
+                                fps = <25>;
+                                bgr;
+                                buswidth = <8>;
+                                dc-gpios = <&gpio 25 0>;
+                                debug = <0>;
+                        };
+                };
+        };
+
+        fragment@3 {
+                target = <&i2c1>;
+                __overlay__ {
+                        /* needed to avoid dtc warning */
+                        #address-cells = <1>;
+                        #size-cells = <0>;
+
+                        ft6236: ft6236@38 {
+                                compatible = "focaltech,ft6236";
+                                reg = <0x38>;
+
+                                interrupt-parent = <&gpio>;
+                                interrupts = <24 2>;
+                                touchscreen-size-x = <240>;
+                                touchscreen-size-y = <320>;
+                        };
+                };
+        };
+
+        __overrides__ {
+                speed =   <&pitft>,"spi-max-frequency:0";
+                rotate =  <&pitft>,"rotate:0";
+                fps =     <&pitft>,"fps:0";
+                debug =   <&pitft>,"debug:0";
+                touch-sizex = <&ft6236>,"touchscreen-size-x?";
+                touch-sizey = <&ft6236>,"touchscreen-size-y?";
+                touch-invx  = <&ft6236>,"touchscreen-inverted-x?";
+                touch-invy  = <&ft6236>,"touchscreen-inverted-y?";
+                touch-swapxy = <&ft6236>,"touchscreen-swapped-x-y?";
+        };
+};

arch/arm/boot/dts/overlays/pitft28-resistive-overlay.dts

@@ -0,0 +1,115 @@
+/*
+ * Device Tree overlay for Adafruit PiTFT 2.8" resistive touch screen
+ *
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
+
+	fragment@0 {
+		target = <&spi0>;
+		__overlay__ {
+			status = "okay";
+
+			spidev@0{
+				status = "disabled";
+			};
+
+			spidev@1{
+				status = "disabled";
+			};
+		};
+	};
+
+	fragment@1 {
+		target = <&gpio>;
+		__overlay__ {
+			pitft_pins: pitft_pins {
+				brcm,pins = <24 25>;
+				brcm,function = <0 1>; /* in out */
+				brcm,pull = <2 0>; /* pullup none */
+			};
+		};
+	};
+
+	fragment@2 {
+		target = <&spi0>;
+		__overlay__ {
+			/* needed to avoid dtc warning */
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			pitft: pitft@0{
+				compatible = "ilitek,ili9340";
+				reg = <0>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pitft_pins>;
+
+				spi-max-frequency = <32000000>;
+				rotate = <90>;
+				fps = <25>;
+				bgr;
+				buswidth = <8>;
+				dc-gpios = <&gpio 25 0>;
+				debug = <0>;
+			};
+
+			pitft_ts@1 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stmpe610";
+				reg = <1>;
+
+				spi-max-frequency = <500000>;
+				irq-gpio = <&gpio 24 0x2>; /* IRQF_TRIGGER_FALLING */
+				interrupts = <24 2>; /* high-to-low edge triggered */
+				interrupt-parent = <&gpio>;
+				interrupt-controller;
+
+				stmpe_touchscreen {
+					compatible = "st,stmpe-ts";
+					st,sample-time = <4>;
+					st,mod-12b = <1>;
+					st,ref-sel = <0>;
+					st,adc-freq = <2>;
+					st,ave-ctrl = <3>;
+					st,touch-det-delay = <4>;
+					st,settling = <2>;
+					st,fraction-z = <7>;
+					st,i-drive = <0>;
+				};
+
+				stmpe_gpio: stmpe_gpio {
+					#gpio-cells = <2>;
+					compatible = "st,stmpe-gpio";
+					/*
+					 * only GPIO2 is wired/available
+					 * and it is wired to the backlight
+					 */
+					st,norequest-mask = <0x7b>;
+				};
+			};
+		};
+	};
+
+	fragment@3 {
+		target-path = "/soc";
+		__overlay__ {
+			backlight {
+				compatible = "gpio-backlight";
+				gpios = <&stmpe_gpio 2 0>;
+				default-on;
+			};
+		};
+	};
+
+	__overrides__ {
+		speed =   <&pitft>,"spi-max-frequency:0";
+		rotate =  <&pitft>,"rotate:0";
+		fps =     <&pitft>,"fps:0";
+		debug =   <&pitft>,"debug:0";
+	};
+};

arch/arm/boot/dts/overlays/pps-gpio-overlay.dts

@@ -0,0 +1,34 @@
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+	fragment@0 {
+		target-path = "/";
+		__overlay__ {
+			pps: pps {
+				compatible = "pps-gpio";
+				pinctrl-names = "default";
+				pinctrl-0 = <&pps_pins>;
+				gpios = <&gpio 18 0>;
+				status = "okay";
+			};
+		};
+	};
+
+	fragment@1 {
+		target = <&gpio>;
+		__overlay__ {
+			pps_pins: pps_pins {
+				brcm,pins =     <18>;
+				brcm,function = <0>;    // in
+				brcm,pull =     <0>;    // off
+			};
+		};
+	};
+
+	__overrides__ {
+		gpiopin = <&pps>,"gpios:4",
+			  <&pps_pins>,"brcm,pins:0";
+	};
+};

arch/arm/boot/dts/overlays/pwm-2chan-overlay.dts

@@ -0,0 +1,46 @@
+/dts-v1/;
+/plugin/;
+
+/*
+This is the 2-channel overlay - only use it if you need both channels.
+
+Legal pin,function combinations for each channel:
+  PWM0: 12,4(Alt0) 18,2(Alt5) 40,4(Alt0)            52,5(Alt1)
+  PWM1: 13,4(Alt0) 19,2(Alt5) 41,4(Alt0) 45,4(Alt0) 53,5(Alt1)
+
+N.B.:
+  1) Pin 18 is the only one available on all platforms, and
+     it is the one used by the I2S audio interface.
+     Pins 12 and 13 might be better choices on an A+, B+ or Pi2.
+  2) The onboard analogue audio output uses both PWM channels.
+  3) So be careful mixing audio and PWM.
+*/
+
+/ {
+	fragment@0 {
+		target = <&gpio>;
+		__overlay__ {
+			pwm_pins: pwm_pins {
+				brcm,pins = <18 19>;
+				brcm,function = <2 2>; /* Alt5 */
+			};
+		};
+	};
+
+	fragment@1 {
+		target = <&pwm>;
+		__overlay__ {
+			pinctrl-names = "default";
+			pinctrl-0 = <&pwm_pins>;
+			status = "okay";
+		};
+	};
+
+	__overrides__ {
+		pin   = <&pwm_pins>,"brcm,pins:0";
+		pin2  = <&pwm_pins>,"brcm,pins:4";
+		func  = <&pwm_pins>,"brcm,function:0";
+		func2 = <&pwm_pins>,"brcm,function:4";
+		clock = <&clk_pwm>,"clock-frequency:0";
+	};
+};

arch/arm/boot/dts/overlays/pwm-overlay.dts

@@ -0,0 +1,42 @@
+/dts-v1/;
+/plugin/;
+
+/*
+Legal pin,function combinations for each channel:
+  PWM0: 12,4(Alt0) 18,2(Alt5) 40,4(Alt0)            52,5(Alt1)
+  PWM1: 13,4(Alt0) 19,2(Alt5) 41,4(Alt0) 45,4(Alt0) 53,5(Alt1)
+
+N.B.:
+  1) Pin 18 is the only one available on all platforms, and
+     it is the one used by the I2S audio interface.
+     Pins 12 and 13 might be better choices on an A+, B+ or Pi2.
+  2) The onboard analogue audio output uses both PWM channels.
+  3) So be careful mixing audio and PWM.
+*/
+
+/ {
+	fragment@0 {
+		target = <&gpio>;
+		__overlay__ {
+			pwm_pins: pwm_pins {
+				brcm,pins = <18>;
+				brcm,function = <2>; /* Alt5 */
+			};
+		};
+	};
+
+	fragment@1 {
+		target = <&pwm>;
+		__overlay__ {
+			pinctrl-names = "default";
+			pinctrl-0 = <&pwm_pins>;
+			status = "okay";
+		};
+	};
+
+	__overrides__ {
+		pin   = <&pwm_pins>,"brcm,pins:0";
+		func  = <&pwm_pins>,"brcm,function:0";
+		clock = <&clk_pwm>,"clock-frequency:0";
+	};
+};

arch/arm/boot/dts/overlays/raspidac3-overlay.dts

@@ -0,0 +1,45 @@
+// Definitions for RaspiDACv3
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&sound>;
+		__overlay__ {
+			compatible = "jg,raspidacv3";
+			i2s-controller = <&i2s>;
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&i2s>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@2 {
+		target = <&i2c1>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			pcm5122@4c {
+				#sound-dai-cells = <0>;
+				compatible = "ti,pcm5122";
+				reg = <0x4c>;
+				status = "okay";
+			};
+
+			tpa6130a2: tpa6130a2@60 {
+				compatible = "ti,tpa6130a2";
+				reg = <0x60>;
+				status = "okay";
+			};
+		};
+	};
+};

arch/arm/boot/dts/overlays/rpi-backlight-overlay.dts

@@ -0,0 +1,21 @@
+/*
+ * Devicetree overlay for mailbox-driven Raspberry Pi DSI Display
+ * backlight controller
+ */
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target-path = "/";
+		__overlay__ {
+			rpi_backlight: rpi_backlight {
+				compatible = "raspberrypi,rpi-backlight";
+				firmware = <&firmware>;
+				status = "okay";
+			};
+		};
+	};
+};

arch/arm/boot/dts/overlays/rpi-dac-overlay.dts

@@ -0,0 +1,34 @@
+// Definitions for RPi DAC
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&sound>;
+		__overlay__ {
+			compatible = "rpi,rpi-dac";
+			i2s-controller = <&i2s>;
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&i2s>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@2 {
+		target-path = "/";
+		__overlay__ {
+			pcm1794a-codec {
+				#sound-dai-cells = <0>;
+				compatible = "ti,pcm1794a";
+				status = "okay";
+			};
+		};
+	};
+};

arch/arm/boot/dts/overlays/rpi-display-overlay.dts

@@ -0,0 +1,82 @@
+/*
+ * Device Tree overlay for rpi-display by Watterott
+ *
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
+
+	fragment@0 {
+		target = <&spi0>;
+		__overlay__ {
+			status = "okay";
+
+			spidev@0{
+				status = "disabled";
+			};
+
+			spidev@1{
+				status = "disabled";
+			};
+		};
+	};
+
+	fragment@1 {
+		target = <&gpio>;
+		__overlay__ {
+			rpi_display_pins: rpi_display_pins {
+				brcm,pins = <18 23 24 25>;
+				brcm,function = <1 1 1 0>; /* out out out in */
+				brcm,pull = <0 0 0 2>; /* - - - up */
+			};
+		};
+	};
+
+	fragment@2 {
+		target = <&spi0>;
+		__overlay__ {
+			/* needed to avoid dtc warning */
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			rpidisplay: rpi-display@0{
+				compatible = "ilitek,ili9341";
+				reg = <0>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&rpi_display_pins>;
+
+				spi-max-frequency = <32000000>;
+				rotate = <270>;
+				bgr;
+				fps = <30>;
+				buswidth = <8>;
+				reset-gpios = <&gpio 23 0>;
+				dc-gpios = <&gpio 24 0>;
+				led-gpios = <&gpio 18 1>;
+				debug = <0>;
+			};
+
+			rpidisplay_ts: rpi-display-ts@1 {
+				compatible = "ti,ads7846";
+				reg = <1>;
+
+				spi-max-frequency = <2000000>;
+				interrupts = <25 2>; /* high-to-low edge triggered */
+				interrupt-parent = <&gpio>;
+				pendown-gpio = <&gpio 25 0>;
+				ti,x-plate-ohms = /bits/ 16 <60>;
+				ti,pressure-max = /bits/ 16 <255>;
+			};
+		};
+	};
+	__overrides__ {
+		speed =   <&rpidisplay>,"spi-max-frequency:0";
+		rotate =  <&rpidisplay>,"rotate:0";
+		fps =     <&rpidisplay>,"fps:0";
+		debug =   <&rpidisplay>,"debug:0";
+		xohms =   <&rpidisplay_ts>,"ti,x-plate-ohms;0";
+	};
+};

arch/arm/boot/dts/overlays/rpi-ft5406-overlay.dts

@@ -0,0 +1,17 @@
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target-path = "/";
+		__overlay__ {
+			rpi_ft5406: rpi_ft5406 {
+				compatible = "rpi,rpi-ft5406";
+				firmware = <&firmware>;
+				status = "okay";
+			};
+		};
+	};
+};

arch/arm/boot/dts/overlays/rpi-proto-overlay.dts

@@ -0,0 +1,39 @@
+// Definitions for Rpi-Proto
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&sound>;
+		__overlay__ {
+			compatible = "rpi,rpi-proto";
+			i2s-controller = <&i2s>;
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&i2s>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@2 {
+		target = <&i2c1>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			wm8731@1a {
+				#sound-dai-cells = <0>;
+				compatible = "wlf,wm8731";
+				reg = <0x1a>;
+				status = "okay";
+			};
+		};
+	};
+};

arch/arm/boot/dts/overlays/rpi-sense-overlay.dts

@@ -0,0 +1,47 @@
+// rpi-sense HAT
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708", "brcm,bcm2709";
+
+	fragment@0 {
+		target = <&i2c1>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			rpi-sense@46 {
+				compatible = "rpi,rpi-sense";
+				reg = <0x46>;
+				keys-int-gpios = <&gpio 23 1>;
+				status = "okay";
+			};
+
+			lsm9ds1-magn@1c {
+				compatible = "st,lsm9ds1-magn";
+				reg = <0x1c>;
+				status = "okay";
+			};
+
+			lsm9ds1-accel6a {
+				compatible = "st,lsm9ds1-accel";
+				reg = <0x6a>;
+				status = "okay";
+			};
+
+			lps25h-press@5c {
+				compatible = "st,lps25h-press";
+				reg = <0x5c>;
+				status = "okay";
+			};
+
+			hts221-humid@5f {
+				compatible = "st,hts221-humid";
+				reg = <0x5f>;
+				status = "okay";
+			};
+		};
+	};
+};

arch/arm/boot/dts/overlays/sdhost-overlay.dts

@@ -0,0 +1,31 @@
+/dts-v1/;
+/plugin/;
+
+/* Provide backwards compatible aliases for the old sdhost dtparams. */
+
+/{
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&sdhost>;
+		frag0: __overlay__ {
+			brcm,overclock-50 = <0>;
+			brcm,pio-limit = <1>;
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&mmc>;
+		__overlay__ {
+			status = "disabled";
+		};
+	};
+
+	__overrides__ {
+		overclock_50     = <&frag0>,"brcm,overclock-50:0";
+		force_pio        = <&frag0>,"brcm,force-pio?";
+		pio_limit        = <&frag0>,"brcm,pio-limit:0";
+		debug            = <&frag0>,"brcm,debug?";
+	};
+};

arch/arm/boot/dts/overlays/sdio-overlay.dts

@@ -0,0 +1,36 @@
+/* Enable SDIO from MMC interface via GPIOs 22-27. Includes sdhost overlay. */
+
+/include/ "sdhost-overlay.dts"
+
+/{
+	compatible = "brcm,bcm2708";
+
+	fragment@3 {
+		target = <&mmc>;
+		sdio_mmc: __overlay__ {
+			pinctrl-names = "default";
+			pinctrl-0 = <&sdio_pins>;
+			non-removable;
+			bus-width = <4>;
+			brcm,overclock-50 = <0>;
+			status = "okay";
+		};
+	};
+
+	fragment@4 {
+		target = <&gpio>;
+		__overlay__ {
+			sdio_pins: sdio_pins {
+				brcm,pins = <22 23 24 25 26 27>;
+				brcm,function = <7 7 7 7 7 7>; /* ALT3 = SD1 */
+				brcm,pull = <0 2 2 2 2 2>;
+			};
+		};
+	};
+
+	__overrides__ {
+		poll_once = <&sdio_mmc>,"non-removable?";
+		bus_width = <&sdio_mmc>,"bus-width:0";
+		sdio_overclock = <&sdio_mmc>,"brcm,overclock-50:0";
+	};
+};

arch/arm/boot/dts/overlays/smi-dev-overlay.dts

@@ -0,0 +1,18 @@
+// Description: Overlay to enable character device interface for SMI.
+// Author:	Luke Wren <luke@raspberrypi.org>
+
+/dts-v1/;
+/plugin/;
+
+/{
+	fragment@0 {
+		target = <&soc>;
+		__overlay__ {
+			smi_dev {
+				compatible = "brcm,bcm2835-smi-dev";
+				smi_handle = <&smi>;
+				status = "okay";
+			};
+		};
+	};
+};

arch/arm/boot/dts/overlays/smi-nand-overlay.dts

@@ -0,0 +1,69 @@
+// Description: Overlay to enable NAND flash through
+// the secondary memory interface
+// Author:	Luke Wren
+
+/dts-v1/;
+/plugin/;
+
+/{
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&smi>;
+		__overlay__ {
+			pinctrl-names = "default";
+			pinctrl-0 = <&smi_pins>;
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&soc>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			nand: flash@0 {
+				compatible = "brcm,bcm2835-smi-nand";
+				smi_handle = <&smi>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				status = "okay";
+
+				partition@0 {
+					label = "stage2";
+					// 128k
+					reg = <0 0x20000>;
+					read-only;
+				};
+				partition@1 {
+					label = "firmware";
+					// 16M
+					reg = <0x20000 0x1000000>;
+					read-only;
+				};
+				partition@2 {
+					label = "root";
+					// 2G (will need to use 64 bit for >=4G)
+					reg = <0x1020000 0x80000000>;
+				};
+			};
+		};
+	};
+
+	fragment@2 {
+		target = <&gpio>;
+		__overlay__ {
+			smi_pins: smi_pins {
+				brcm,pins = <0 1 2 3 4 5 6 7 8 9 10 11
+					12 13 14 15>;
+				/* Alt 1: SMI */
+				brcm,function = <5 5 5 5 5 5 5 5 5 5 5
+					5 5 5 5 5>;
+				/* /CS, /WE and /OE are pulled high, as they are
+				   generally active low signals */
+				brcm,pull = <2 2 2 2 2 2 2 2 0 0 0 0 0 0 0 0>;
+			};
+		};
+	};
+};

arch/arm/boot/dts/overlays/smi-overlay.dts

@@ -0,0 +1,37 @@
+// Description:	Overlay to enable the secondary memory interface peripheral
+// Author:	Luke Wren
+
+/dts-v1/;
+/plugin/;
+
+/{
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&smi>;
+		__overlay__ {
+			pinctrl-names = "default";
+			pinctrl-0 = <&smi_pins>;
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&gpio>;
+		__overlay__ {
+			smi_pins: smi_pins {
+				/* Don't configure the top two address bits, as
+				   these are already used as ID_SD and ID_SC */
+				brcm,pins = <2 3 4 5 6 7 8 9 10 11 12 13 14 15
+					     16 17 18 19 20 21 22 23 24 25>;
+				/* Alt 0: SMI */
+				brcm,function = <5 5 5 5 5 5 5 5 5 5 5 5 5 5 5
+						 5 5 5 5 5 5 5 5 5>;
+				/* /CS, /WE and /OE are pulled high, as they are
+				   generally active low signals */
+				brcm,pull = <2 2 2 2 2 2 0 0 0 0 0 0 0 0 0 0 0
+					     0 0 0 0 0 0 0>;
+			};
+		};
+	};
+};

arch/arm/boot/dts/overlays/spi-gpio35-39-overlay.dts

@@ -0,0 +1,31 @@
+/*
+ * Device tree overlay to move spi0 to gpio 35 to 39 on CM
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2835", "brcm,bcm2836", "brcm,bcm2708", "brcm,bcm2709";
+
+	fragment@0 {
+		target = <&spi0>;
+		__overlay__ {
+			cs-gpios = <&gpio 36 1>, <&gpio 35 1>;
+		};
+	};
+
+	fragment@1 {
+		target = <&spi0_cs_pins>;
+		__overlay__ {
+			bcrm,pins = <36 35>;
+		};
+	};
+
+	fragment@2 {
+		target = <&spi0_pins>;
+		__overlay__ {
+			bcrm,pins = <37 38 39>;
+		};
+	};
+};

arch/arm/boot/dts/overlays/tinylcd35-overlay.dts

@@ -0,0 +1,216 @@
+/*
+ * tinylcd35-overlay.dts
+ *
+ * -------------------------------------------------
+ * www.tinlylcd.com
+ * -------------------------------------------------
+ * Device---Driver-----BUS       GPIO's
+ * display  tinylcd35  spi0.0    25 24 18
+ * touch    ads7846    spi0.1    5
+ * rtc      ds1307     i2c1-0068
+ * rtc      pcf8563    i2c1-0051
+ * keypad   gpio-keys  --------- 17 22 27 23 28
+ *
+ *
+ * TinyLCD.com 3.5 inch TFT
+ *
+ *  Version 001
+ *  5/3/2015  -- Noralf Trønnes     Initial Device tree framework
+ *  10/3/2015 -- tinylcd@gmail.com  added ds1307 support.
+ *
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
+
+	fragment@0 {
+		target = <&spi0>;
+		__overlay__ {
+			status = "okay";
+
+			spidev@0{
+				status = "disabled";
+			};
+
+			spidev@1{
+				status = "disabled";
+			};
+		};
+	};
+
+	fragment@1 {
+		target = <&gpio>;
+		__overlay__ {
+			tinylcd35_pins: tinylcd35_pins {
+				brcm,pins = <25 24 18>;
+				brcm,function = <1>; /* out */
+			};
+			tinylcd35_ts_pins: tinylcd35_ts_pins {
+				brcm,pins = <5>;
+				brcm,function = <0>; /* in */
+			};
+			keypad_pins: keypad_pins {
+				brcm,pins = <4 17 22 23 27>;
+				brcm,function = <0>; /* in */
+				brcm,pull = <1>; /* down */
+			};
+		};
+	};
+
+	fragment@2 {
+		target = <&spi0>;
+		__overlay__ {
+			/* needed to avoid dtc warning */
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			tinylcd35: tinylcd35@0{
+				compatible = "neosec,tinylcd";
+				reg = <0>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&tinylcd35_pins>,
+					    <&tinylcd35_ts_pins>;
+
+				spi-max-frequency = <48000000>;
+				rotate = <270>;
+				fps = <20>;
+				bgr;
+				buswidth = <8>;
+				reset-gpios = <&gpio 25 0>;
+				dc-gpios = <&gpio 24 0>;
+				led-gpios = <&gpio 18 1>;
+				debug = <0>;
+
+				init = <0x10000B0 0x80
+					0x10000C0 0x0A 0x0A
+					0x10000C1 0x01 0x01
+					0x10000C2 0x33
+					0x10000C5 0x00 0x42 0x80
+					0x10000B1 0xD0 0x11
+					0x10000B4 0x02
+					0x10000B6 0x00 0x22 0x3B
+					0x10000B7 0x07
+					0x1000036 0x58
+					0x10000F0 0x36 0xA5 0xD3
+					0x10000E5 0x80
+					0x10000E5 0x01
+					0x10000B3 0x00
+					0x10000E5 0x00
+					0x10000F0 0x36 0xA5 0x53
+					0x10000E0 0x00 0x35 0x33 0x00 0x00 0x00 0x00 0x35 0x33 0x00 0x00 0x00
+					0x100003A 0x55
+					0x1000011
+					0x2000001
+					0x1000029>;
+			};
+
+			tinylcd35_ts: tinylcd35_ts@1 {
+				compatible = "ti,ads7846";
+				reg = <1>;
+				status = "disabled";
+
+				spi-max-frequency = <2000000>;
+				interrupts = <5 2>; /* high-to-low edge triggered */
+				interrupt-parent = <&gpio>;
+				pendown-gpio = <&gpio 5 0>;
+				ti,x-plate-ohms = /bits/ 16 <100>;
+				ti,pressure-max = /bits/ 16 <255>;
+			};
+		};
+	};
+
+	/*  RTC    */
+
+	fragment@3 {
+		target = <&i2c1>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			pcf8563: pcf8563@51 {
+				compatible = "nxp,pcf8563";
+				reg = <0x51>;
+				status = "disabled";
+			};
+		};
+	};
+
+	fragment@4 {
+		target = <&i2c1>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			ds1307: ds1307@68 {
+				compatible = "maxim,ds1307";
+				reg = <0x68>;
+				status = "disabled";
+			};
+		};
+	};
+
+	/*
+	 * Values for input event code is found under the
+	 * 'Keys and buttons' heading in include/uapi/linux/input.h
+	 */
+	fragment@5 {
+		target-path = "/soc";
+		__overlay__ {
+			keypad: keypad {
+				compatible = "gpio-keys";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&keypad_pins>;
+				status = "disabled";
+				autorepeat;
+
+				button@17 {
+					label = "GPIO KEY_UP";
+					linux,code = <103>;
+					gpios = <&gpio 17 0>;
+				};
+				button@22 {
+					label = "GPIO KEY_DOWN";
+					linux,code = <108>;
+					gpios = <&gpio 22 0>;
+				};
+				button@27 {
+					label = "GPIO KEY_LEFT";
+					linux,code = <105>;
+					gpios = <&gpio 27 0>;
+				};
+				button@23 {
+					label = "GPIO KEY_RIGHT";
+					linux,code = <106>;
+					gpios = <&gpio 23 0>;
+				};
+				button@4 {
+					label = "GPIO KEY_ENTER";
+					linux,code = <28>;
+					gpios = <&gpio 4 0>;
+				};
+			};
+		};
+	};
+
+	__overrides__ {
+		speed =      <&tinylcd35>,"spi-max-frequency:0";
+		rotate =     <&tinylcd35>,"rotate:0";
+		fps =        <&tinylcd35>,"fps:0";
+		debug =      <&tinylcd35>,"debug:0";
+		touch =      <&tinylcd35_ts>,"status";
+		touchgpio =  <&tinylcd35_ts_pins>,"brcm,pins:0",
+			     <&tinylcd35_ts>,"interrupts:0",
+			     <&tinylcd35_ts>,"pendown-gpio:4";
+		xohms =      <&tinylcd35_ts>,"ti,x-plate-ohms;0";
+		rtc-pcf =    <&i2c1>,"status",
+			     <&pcf8563>,"status";
+		rtc-ds =     <&i2c1>,"status",
+			     <&ds1307>,"status";
+		keypad =     <&keypad>,"status";
+	};
+};

arch/arm/boot/dts/overlays/uart1-overlay.dts

@@ -0,0 +1,38 @@
+/dts-v1/;
+/plugin/;
+
+/{
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&uart1>;
+		__overlay__ {
+			pinctrl-names = "default";
+			pinctrl-0 = <&uart1_pins>;
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&gpio>;
+		__overlay__ {
+			uart1_pins: uart1_pins {
+				brcm,pins = <14 15>;
+				brcm,function = <2>; /* alt5 */
+				brcm,pull = <0 2>;
+			};
+		};
+	};
+
+	fragment@2 {
+		target-path = "/chosen";
+		__overlay__ {
+			bootargs = "8250.nr_uarts=1";
+		};
+	};
+
+	__overrides__ {
+		txd1_pin = <&uart1_pins>,"brcm,pins:0";
+		rxd1_pin = <&uart1_pins>,"brcm,pins:4";
+	};
+};

arch/arm/boot/dts/overlays/vc4-kms-v3d-overlay.dts

@@ -0,0 +1,95 @@
+/*
+ * vc4-kms-v3d-overlay.dts
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include "dt-bindings/clock/bcm2835.h"
+#include "dt-bindings/gpio/gpio.h"
+
+/ {
+	compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
+
+	fragment@0 {
+		target = <&i2c2>;
+		__overlay__  {
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&cprman>;
+		__overlay__  {
+			status = "okay";
+		};
+	};
+
+	fragment@2 {
+		target = <&fb>;
+		__overlay__  {
+			status = "disabled";
+		};
+	};
+
+	fragment@3 {
+		target = <&soc>;
+		__overlay__  {
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			pixelvalve@7e206000 {
+				compatible = "brcm,bcm2835-pixelvalve0";
+				reg = <0x7e206000 0x100>;
+				interrupts = <2 13>; /* pwa0 */
+			};
+
+			pixelvalve@7e207000 {
+				compatible = "brcm,bcm2835-pixelvalve1";
+				reg = <0x7e207000 0x100>;
+				interrupts = <2 14>; /* pwa1 */
+			};
+
+			hvs@7e400000 {
+				compatible = "brcm,bcm2835-hvs";
+				reg = <0x7e400000 0x6000>;
+				interrupts = <2 1>;
+			};
+
+			pixelvalve@7e807000 {
+				compatible = "brcm,bcm2835-pixelvalve2";
+				reg = <0x7e807000 0x100>;
+				interrupts = <2 10>; /* pixelvalve */
+			};
+
+			hdmi@7e902000 {
+				compatible = "brcm,bcm2835-hdmi";
+				reg = <0x7e902000 0x600>,
+				      <0x7e808000 0x100>;
+				interrupts = <2 8>, <2 9>;
+				ddc = <&i2c2>;
+				hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
+				clocks = <&cprman BCM2835_PLLH_PIX>,
+					 <&cprman BCM2835_CLOCK_HSM>;
+				clock-names = "pixel", "hdmi";
+			};
+
+			v3d@7ec00000 {
+				compatible = "brcm,vc4-v3d";
+				reg = <0x7ec00000 0x1000>;
+				interrupts = <1 10>;
+			};
+
+			gpu@7e4c0000 {
+				compatible = "brcm,bcm2835-vc4";
+			};
+		};
+	};
+
+	fragment@4 {
+		target-path = "/chosen";
+		__overlay__ {
+			bootargs = "cma=256M@512M";
+		};
+	};
+};

arch/arm/boot/dts/overlays/vga666-overlay.dts

@@ -0,0 +1,30 @@
+/dts-v1/;
+/plugin/;
+
+/{
+	compatible = "brcm,bcm2708";
+
+	// There is no VGA driver module, but we need a platform device
+	// node (that doesn't already use pinctrl) to hang the pinctrl
+	// reference on - leds will do
+
+	fragment@0 {
+		target = <&leds>;
+		__overlay__ {
+			pinctrl-names = "default";
+			pinctrl-0 = <&vga666_pins>;
+		};
+	};
+
+	fragment@1 {
+		target = <&gpio>;
+		__overlay__ {
+			vga666_pins: vga666_pins {
+				brcm,pins = <2 3 4 5 6 7 8 9 10 11 12
+					     13 14 15 16 17 18 19 20 21>;
+				brcm,function = <6>; /* alt2 */
+				brcm,pull = <0>; /* no pull */
+			};
+		};
+	};
+};

arch/arm/boot/dts/overlays/w1-gpio-overlay.dts

@@ -0,0 +1,39 @@
+// Definitions for w1-gpio module (without external pullup)
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target-path = "/";
+		__overlay__ {
+
+			w1: onewire@0 {
+				compatible = "w1-gpio";
+				pinctrl-names = "default";
+				pinctrl-0 = <&w1_pins>;
+				gpios = <&gpio 4 0>;
+				rpi,parasitic-power = <0>;
+				status = "okay";
+			};
+		};
+	};
+
+	fragment@1 {
+		target = <&gpio>;
+		__overlay__ {
+			w1_pins: w1_pins {
+				brcm,pins = <4>;
+				brcm,function = <0>; // in (initially)
+				brcm,pull = <0>; // off
+			};
+		};
+	};
+
+	__overrides__ {
+		gpiopin =       <&w1>,"gpios:4",
+				<&w1_pins>,"brcm,pins:0";
+		pullup =        <&w1>,"rpi,parasitic-power:0";
+	};
+};

arch/arm/boot/dts/overlays/w1-gpio-pullup-overlay.dts

@@ -0,0 +1,41 @@
+// Definitions for w1-gpio module (with external pullup)
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target-path = "/";
+		__overlay__ {
+
+			w1: onewire@0 {
+				compatible = "w1-gpio";
+				pinctrl-names = "default";
+				pinctrl-0 = <&w1_pins>;
+				gpios = <&gpio 4 0>, <&gpio 5 1>;
+				rpi,parasitic-power = <0>;
+				status = "okay";
+			};
+		};
+	};
+
+	fragment@1 {
+		target = <&gpio>;
+		__overlay__ {
+			w1_pins: w1_pins {
+				brcm,pins = <4 5>;
+				brcm,function = <0 1>; // in out
+				brcm,pull = <0 0>; // off off
+			};
+		};
+	};
+
+	__overrides__ {
+		gpiopin =       <&w1>,"gpios:4",
+				<&w1_pins>,"brcm,pins:0";
+		extpullup =     <&w1>,"gpios:16",
+				<&w1_pins>,"brcm,pins:4";
+		pullup =        <&w1>,"rpi,parasitic-power:0";
+	};
+};

arch/arm/boot/dts/sama5d4.dtsi

@@ -939,11 +939,11 @@
 				reg = <0xf8018000 0x4000>;
 				interrupts = <33 IRQ_TYPE_LEVEL_HIGH 6>;
 				dmas = <&dma1
-					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1))
+					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
-					AT91_XDMAC_DT_PERID(4)>,
+					| AT91_XDMAC_DT_PERID(4))>,
 				       <&dma1
-					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1))
+					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
-					AT91_XDMAC_DT_PERID(5)>;
+					| AT91_XDMAC_DT_PERID(5))>;
 				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_i2c1>;

arch/arm/boot/dts/sun6i-a31-hummingbird.dts

@@ -184,20 +184,20 @@
 				regulator-name = "vcc-3v0";
 			};
 
-			vdd_cpu: dcdc2 {
+			vdd_gpu: dcdc2 {
-				regulator-always-on;
-				regulator-min-microvolt = <700000>;
-				regulator-max-microvolt = <1320000>;
-				regulator-name = "vdd-cpu";
-			};
-
-			vdd_gpu: dcdc3 {
 				regulator-always-on;
 				regulator-min-microvolt = <700000>;
 				regulator-max-microvolt = <1320000>;
 				regulator-name = "vdd-gpu";
 			};
 
+			vdd_cpu: dcdc3 {
+				regulator-always-on;
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1320000>;
+				regulator-name = "vdd-cpu";
+			};
+
 			vdd_sys_dll: dcdc4 {
 				regulator-always-on;
 				regulator-min-microvolt = <1100000>;

arch/arm/common/edma.c

@@ -406,7 +406,8 @@ static irqreturn_t dma_irq_handler(int irq, void *data)
 					BIT(slot));
 			if (edma_cc[ctlr]->intr_data[channel].callback)
 				edma_cc[ctlr]->intr_data[channel].callback(
-					channel, EDMA_DMA_COMPLETE,
+					EDMA_CTLR_CHAN(ctlr, channel),
+					EDMA_DMA_COMPLETE,
 					edma_cc[ctlr]->intr_data[channel].data);
 		}
 	} while (sh_ipr);
@@ -460,7 +461,8 @@ static irqreturn_t dma_ccerr_handler(int irq, void *data)
 					if (edma_cc[ctlr]->intr_data[k].
 								callback) {
 						edma_cc[ctlr]->intr_data[k].
-						callback(k,
+						callback(
+						EDMA_CTLR_CHAN(ctlr, k),
 						EDMA_DMA_CC_ERROR,
 						edma_cc[ctlr]->intr_data
 						[k].data);