config: recreate with savedefconfig

Depending on the connected IR circuitry it might be desirable to change the
gpios internal pull from it pull-down default behaviour. Add a module
parameter to allow the user to set it explicitly.

Signed-off-by: Julian Scheel <julian@jusst.de>

Documentation/devicetree/bindings/interrupt-controller/interrupts.txt

@@ -4,11 +4,13 @@ Specifying interrupt information for devices
 1) Interrupt client nodes
 -------------------------
 
-Nodes that describe devices which generate interrupts must contain an either an
-"interrupts" property or an "interrupts-extended" property. These properties
-contain a list of interrupt specifiers, one per output interrupt. The format of
-the interrupt specifier is determined by the interrupt controller to which the
-interrupts are routed; see section 2 below for details.
+Nodes that describe devices which generate interrupts must contain an
+"interrupts" property, an "interrupts-extended" property, or both. If both are
+present, the latter should take precedence; the former may be provided simply
+for compatibility with software that does not recognize the latter. These
+properties contain a list of interrupt specifiers, one per output interrupt. The
+format of the interrupt specifier is determined by the interrupt controller to
+which the interrupts are routed; see section 2 below for details.
 
   Example:
 	interrupt-parent = <&intc1>;

Documentation/devicetree/bindings/sound/adi,axi-spdif-tx.txt

@@ -1,7 +1,7 @@
 ADI AXI-SPDIF controller
 
 Required properties:
- - compatible : Must be "adi,axi-spdif-1.00.a"
+ - compatible : Must be "adi,axi-spdif-tx-1.00.a"
  - reg : Must contain SPDIF core's registers location and length
  - clocks : Pairs of phandle and specifier referencing the controller's clocks.
    The controller expects two clocks, the clock used for the AXI interface and

Documentation/devicetree/bindings/staging/imx-drm/ldb.txt

@@ -56,6 +56,9 @@ Required properties:
  - fsl,data-width : should be <18> or <24>
  - port: A port node with endpoint definitions as defined in
    Documentation/devicetree/bindings/media/video-interfaces.txt.
+   On i.MX5, the internal two-input-multiplexer is used.
+   Due to hardware limitations, only one port (port@[0,1])
+   can be used for each channel (lvds-channel@[0,1], respectively)
    On i.MX6, there should be four ports (port@[0-3]) that correspond
    to the four LVDS multiplexer inputs.
 
@@ -78,6 +81,8 @@ ldb: ldb@53fa8008 {
 		      "di0", "di1";
 
 	lvds-channel@0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
 		reg = <0>;
 		fsl,data-mapping = "spwg";
 		fsl,data-width = <24>;
@@ -86,7 +91,9 @@ ldb: ldb@53fa8008 {
 			/* ... */
 		};
 
-		port {
+		port@0 {
+			reg = <0>;
+
 			lvds0_in: endpoint {
 				remote-endpoint = <&ipu_di0_lvds0>;
 			};
@@ -94,6 +101,8 @@ ldb: ldb@53fa8008 {
 	};
 
 	lvds-channel@1 {
+		#address-cells = <1>;
+		#size-cells = <0>;
 		reg = <1>;
 		fsl,data-mapping = "spwg";
 		fsl,data-width = <24>;
@@ -102,7 +111,9 @@ ldb: ldb@53fa8008 {
 			/* ... */
 		};
 
-		port {
+		port@1 {
+			reg = <1>;
+
 			lvds1_in: endpoint {
 				remote-endpoint = <&ipu_di1_lvds1>;
 			};

Documentation/kernel-parameters.txt

@@ -3478,6 +3478,7 @@ bytes respectively. Such letter suffixes can also be entirely omitted.
 					bogus residue values);
 				s = SINGLE_LUN (the device has only one
 					Logical Unit);
+				u = IGNORE_UAS (don't bind to the uas driver);
 				w = NO_WP_DETECT (don't test whether the
 					medium is write-protected).
 			Example: quirks=0419:aaf5:rl,0421:0433:rc

Documentation/sound/alsa/ALSA-Configuration.txt

@@ -2026,8 +2026,8 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
   -------------------
 
     Module for sound cards based on the Asus AV66/AV100/AV200 chips,
-    i.e., Xonar D1, DX, D2, D2X, DS, Essence ST (Deluxe), Essence STX,
-    HDAV1.3 (Deluxe), and HDAV1.3 Slim.
+    i.e., Xonar D1, DX, D2, D2X, DS, DSX, Essence ST (Deluxe),
+    Essence STX (II), HDAV1.3 (Deluxe), and HDAV1.3 Slim.
 
     This module supports autoprobe and multiple cards.
 

Documentation/stable_kernel_rules.txt

@@ -29,6 +29,9 @@ Rules on what kind of patches are accepted, and which ones are not, into the
 
 Procedure for submitting patches to the -stable tree:
 
+ - If the patch covers files in net/ or drivers/net please follow netdev stable
+   submission guidelines as described in
+   Documentation/networking/netdev-FAQ.txt
  - Send the patch, after verifying that it follows the above rules, to
    stable@vger.kernel.org.  You must note the upstream commit ID in the
    changelog of your submission, as well as the kernel version you wish

Documentation/video4linux/bcm2835-v4l2.txt

@@ -0,0 +1,60 @@
+
+BCM2835 (aka Raspberry Pi) V4L2 driver
+======================================
+
+1. Copyright
+============
+
+Copyright © 2013 Raspberry Pi (Trading) Ltd.
+
+2. License
+==========
+
+This program is free software; you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation; either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program; if not, write to the Free Software
+Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+
+3. Quick Start
+==============
+
+You need a version 1.0 or later of v4l2-ctl, available from:
+	git://git.linuxtv.org/v4l-utils.git
+
+$ sudo modprobe bcm2835-v4l2
+
+Turn on the overlay:
+
+$ v4l2-ctl --overlay=1
+
+Turn off the overlay:
+
+$ v4l2-ctl --overlay=0
+
+Set the capture format for video:
+
+$ v4l2-ctl  --set-fmt-video=width=1920,height=1088,pixelformat=4
+
+(Note: 1088 not 1080).
+
+Capture:
+
+$ v4l2-ctl --stream-mmap=3 --stream-count=100 --stream-to=somefile.h264
+
+Stills capture:
+
+$ v4l2-ctl  --set-fmt-video=width=2592,height=1944,pixelformat=3
+$ v4l2-ctl --stream-mmap=3 --stream-count=1 --stream-to=somefile.jpg
+
+List of available formats:
+
+$ v4l2-ctl --list-formats

Documentation/virtual/kvm/api.txt

@@ -1869,7 +1869,8 @@ registers, find a list below:
   PPC   | KVM_REG_PPC_PID	| 64
   PPC   | KVM_REG_PPC_ACOP	| 64
   PPC   | KVM_REG_PPC_VRSAVE	| 32
-  PPC   | KVM_REG_PPC_LPCR	| 64
+  PPC   | KVM_REG_PPC_LPCR	| 32
+  PPC   | KVM_REG_PPC_LPCR_64	| 64
   PPC   | KVM_REG_PPC_PPR	| 64
   PPC   | KVM_REG_PPC_ARCH_COMPAT 32
   PPC   | KVM_REG_PPC_DABRX     | 32

Makefile

@@ -1,8 +1,8 @@
 VERSION = 3
 PATCHLEVEL = 16
-SUBLEVEL = 0
+SUBLEVEL = 5
 EXTRAVERSION =
-NAME = Shuffling Zombie Juror
+NAME = Museum of Fishiegoodies
 
 # *DOCUMENTATION*
 # To see a list of typical targets execute "make help"

arch/arm/Kconfig

@@ -374,6 +374,23 @@ config ARCH_AT91
 	  This enables support for systems based on Atmel
 	  AT91RM9200 and AT91SAM9* processors.
 
+config ARCH_BCM2708
+	bool "Broadcom BCM2708 family"
+	select CPU_V6
+	select ARM_AMBA
+	select HAVE_SCHED_CLOCK
+	select NEED_MACH_GPIO_H
+	select NEED_MACH_MEMORY_H
+	select COMMON_CLK
+	select ARCH_HAS_CPUFREQ
+	select GENERIC_CLOCKEVENTS
+	select ARM_ERRATA_411920
+	select MACH_BCM2708
+	select VC4
+	select FIQ
+	help
+	  This enables support for Broadcom BCM2708 boards.
+
 config ARCH_CLPS711X
 	bool "Cirrus Logic CLPS711x/EP721x/EP731x-based"
 	select ARCH_REQUIRE_GPIOLIB
@@ -1034,6 +1051,7 @@ source "arch/arm/plat-versatile/Kconfig"
 source "arch/arm/mach-vt8500/Kconfig"
 
 source "arch/arm/mach-w90x900/Kconfig"
+source "arch/arm/mach-bcm2708/Kconfig"
 
 source "arch/arm/mach-zynq/Kconfig"
 

arch/arm/Kconfig.debug

@@ -937,6 +937,14 @@ choice
 		  options; the platform specific options are deprecated
 		  and will be soon removed.
 
+	config DEBUG_BCM2708_UART0
+		bool "Broadcom BCM2708 UART0 (PL011)"
+		depends on MACH_BCM2708
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to UART 0. The port must have been initialised
+		  by the boot-loader before use.
+
 endchoice
 
 config DEBUG_EXYNOS_UART

arch/arm/Makefile

@@ -145,6 +145,7 @@ textofs-$(CONFIG_ARCH_AXXIA) := 0x00308000
 machine-$(CONFIG_ARCH_AT91)		+= at91
 machine-$(CONFIG_ARCH_AXXIA)		+= axxia
 machine-$(CONFIG_ARCH_BCM)		+= bcm
+machine-$(CONFIG_ARCH_BCM2708)		+= bcm2708
 machine-$(CONFIG_ARCH_BERLIN)		+= berlin
 machine-$(CONFIG_ARCH_CLPS711X)		+= clps711x
 machine-$(CONFIG_ARCH_CNS3XXX)		+= cns3xxx

arch/arm/boot/dts/Makefile

@@ -51,6 +51,7 @@ dtb-$(CONFIG_ARCH_AT91)	+= sama5d36ek.dtb
 
 dtb-$(CONFIG_ARCH_ATLAS6) += atlas6-evb.dtb
 dtb-$(CONFIG_ARCH_AXXIA) += axm5516-amarillo.dtb
+dtb-$(CONFIG_BCM2708_DT) += bcm2708-rpi-b.dtb
 dtb-$(CONFIG_ARCH_BCM2835) += bcm2835-rpi-b.dtb
 dtb-$(CONFIG_ARCH_BCM_5301X) += bcm4708-netgear-r6250.dtb
 dtb-$(CONFIG_ARCH_BCM_MOBILE) += bcm28155-ap.dtb \

arch/arm/boot/dts/am4372.dtsi

@@ -168,9 +168,6 @@
 			ti,hwmods = "mailbox";
 			ti,mbox-num-users = <4>;
 			ti,mbox-num-fifos = <8>;
-			ti,mbox-names = "wkup_m3";
-			ti,mbox-data = <0 0 0 0>;
-			status = "disabled";
 		};
 
 		timer1: timer@44e31000 {

arch/arm/boot/dts/bcm2708-rpi-b.dts

@@ -0,0 +1,64 @@
+/dts-v1/;
+
+/include/ "bcm2708.dtsi"
+
+/ {
+	compatible = "brcm,bcm2708";
+	model = "Raspberry Pi";
+
+	aliases {
+		spi0 = &spi0;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+	};
+};
+
+&gpio {
+	spi0_pins: spi0_pins {
+		brcm,pins = <7 8 9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins>;
+
+	spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <500000>;
+	};
+
+	spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <500000>;
+	};
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};

arch/arm/boot/dts/bcm2708.dtsi

@@ -0,0 +1,88 @@
+/include/ "skeleton.dtsi"
+
+/ {
+	compatible = "brcm,bcm2708";
+	model = "BCM2708";
+
+	interrupt-parent = <&intc>;
+
+	chosen {
+		/*
+		   bootargs must be 1024 characters long because the
+		   VC bootloader can't expand it
+		*/
+		bootargs = "console=ttyAMA0                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                 ";
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x7e000000 0x20000000 0x02000000>;
+
+		intc: interrupt-controller {
+			compatible = "brcm,bcm2708-armctrl-ic";
+			reg = <0x7e00b200 0x200>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio: gpio {
+			compatible = "brcm,bcm2708-pinctrl";
+			reg = <0x7e200000 0xb4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		spi0: spi@7e204000 {
+			compatible = "brcm,bcm2708-spi";
+			reg = <0x7e204000 0x1000>;
+			interrupts = <2 22>;
+			clocks = <&clk_spi>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c0: i2c@7e205000 {
+			compatible = "brcm,bcm2708-i2c";
+			reg = <0x7e205000 0x1000>;
+			interrupts = <2 21>;
+			clocks = <&clk_i2c>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c1: i2c@7e804000 {
+			compatible = "brcm,bcm2708-i2c";
+			reg = <0x7e804000 0x1000>;
+			interrupts = <2 21>;
+			clocks = <&clk_i2c>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+	};
+
+	clocks {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		clk_i2c: i2c {
+			compatible = "fixed-clock";
+			reg = <1>;
+			#clock-cells = <0>;
+			clock-frequency = <250000000>;
+		};
+
+		clk_spi: clock@2 {
+			compatible = "fixed-clock";
+			reg = <2>;
+			#clock-cells = <0>;
+			clock-output-names = "spi";
+			clock-frequency = <250000000>;
+		};
+	};
+};

arch/arm/boot/dts/dra7-evm.dts

@@ -50,13 +50,13 @@
 
 	mcspi1_pins: pinmux_mcspi1_pins {
 		pinctrl-single,pins = <
-			0x3a4 (PIN_INPUT | MUX_MODE0) /* spi2_clk */
-			0x3a8 (PIN_INPUT | MUX_MODE0) /* spi2_d1 */
-			0x3ac (PIN_INPUT | MUX_MODE0) /* spi2_d0 */
-			0x3b0 (PIN_INPUT_SLEW | MUX_MODE0) /* spi2_cs0 */
-			0x3b4 (PIN_INPUT_SLEW | MUX_MODE0) /* spi2_cs1 */
-			0x3b8 (PIN_INPUT_SLEW | MUX_MODE6) /* spi2_cs2 */
-			0x3bc (PIN_INPUT_SLEW | MUX_MODE6) /* spi2_cs3 */
+			0x3a4 (PIN_INPUT | MUX_MODE0) /* spi1_sclk */
+			0x3a8 (PIN_INPUT | MUX_MODE0) /* spi1_d1 */
+			0x3ac (PIN_INPUT | MUX_MODE0) /* spi1_d0 */
+			0x3b0 (PIN_INPUT_SLEW | MUX_MODE0) /* spi1_cs0 */
+			0x3b4 (PIN_INPUT_SLEW | MUX_MODE0) /* spi1_cs1 */
+			0x3b8 (PIN_INPUT_SLEW | MUX_MODE6) /* spi1_cs2.hdmi1_hpd */
+			0x3bc (PIN_INPUT_SLEW | MUX_MODE6) /* spi1_cs3.hdmi1_cec */
 		>;
 	};
 
@@ -427,22 +427,19 @@
 		gpmc,device-width = <2>;
 		gpmc,sync-clk-ps = <0>;
 		gpmc,cs-on-ns = <0>;
-		gpmc,cs-rd-off-ns = <40>;
-		gpmc,cs-wr-off-ns = <40>;
+		gpmc,cs-rd-off-ns = <80>;
+		gpmc,cs-wr-off-ns = <80>;
 		gpmc,adv-on-ns = <0>;
-		gpmc,adv-rd-off-ns = <30>;
-		gpmc,adv-wr-off-ns = <30>;
-		gpmc,we-on-ns = <5>;
-		gpmc,we-off-ns = <25>;
-		gpmc,oe-on-ns = <2>;
-		gpmc,oe-off-ns = <20>;
-		gpmc,access-ns = <20>;
-		gpmc,wr-access-ns = <40>;
-		gpmc,rd-cycle-ns = <40>;
-		gpmc,wr-cycle-ns = <40>;
-		gpmc,wait-pin = <0>;
-		gpmc,wait-on-read;
-		gpmc,wait-on-write;
+		gpmc,adv-rd-off-ns = <60>;
+		gpmc,adv-wr-off-ns = <60>;
+		gpmc,we-on-ns = <10>;
+		gpmc,we-off-ns = <50>;
+		gpmc,oe-on-ns = <4>;
+		gpmc,oe-off-ns = <40>;
+		gpmc,access-ns = <40>;
+		gpmc,wr-access-ns = <80>;
+		gpmc,rd-cycle-ns = <80>;
+		gpmc,wr-cycle-ns = <80>;
 		gpmc,bus-turnaround-ns = <0>;
 		gpmc,cycle2cycle-delay-ns = <0>;
 		gpmc,clk-activation-ns = <0>;

arch/arm/boot/dts/dra7.dtsi

@@ -172,7 +172,7 @@
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 		};
 
 		gpio2: gpio@48055000 {
@@ -183,7 +183,7 @@
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 		};
 
 		gpio3: gpio@48057000 {
@@ -194,7 +194,7 @@
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 		};
 
 		gpio4: gpio@48059000 {
@@ -205,7 +205,7 @@
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 		};
 
 		gpio5: gpio@4805b000 {
@@ -216,7 +216,7 @@
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 		};
 
 		gpio6: gpio@4805d000 {
@@ -227,7 +227,7 @@
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 		};
 
 		gpio7: gpio@48051000 {
@@ -238,7 +238,7 @@
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 		};
 
 		gpio8: gpio@48053000 {
@@ -249,7 +249,7 @@
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 		};
 
 		uart1: serial@4806a000 {

arch/arm/boot/dts/imx53-qsrb.dts

@@ -28,6 +28,12 @@
 				MX53_PAD_CSI0_DAT9__I2C1_SCL      0x400001ec
 			>;
 		};
+
+		pinctrl_pmic: pmicgrp {
+			fsl,pins = <
+				MX53_PAD_CSI0_DAT5__GPIO5_23	0x1e4 /* IRQ */
+			>;
+		};
 	};
 };
 
@@ -38,6 +44,8 @@
 
 	pmic: mc34708@8 {
 		compatible = "fsl,mc34708";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pmic>;
 		reg = <0x08>;
 		interrupt-parent = <&gpio5>;
 		interrupts = <23 0x8>;

arch/arm/boot/dts/imx53.dtsi

@@ -419,10 +419,14 @@
 				status = "disabled";
 
 				lvds-channel@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
 					reg = <0>;
 					status = "disabled";
 
-					port {
+					port@0 {
+						reg = <0>;
+
 						lvds0_in: endpoint {
 							remote-endpoint = <&ipu_di0_lvds0>;
 						};
@@ -430,10 +434,14 @@
 				};
 
 				lvds-channel@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
 					reg = <1>;
 					status = "disabled";
 
-					port {
+					port@1 {
+						reg = <1>;
+
 						lvds1_in: endpoint {
 							remote-endpoint = <&ipu_di1_lvds1>;
 						};
@@ -724,7 +732,7 @@
 				compatible = "fsl,imx53-vpu";
 				reg = <0x63ff4000 0x1000>;
 				interrupts = <9>;
-				clocks = <&clks IMX5_CLK_VPU_GATE>,
+				clocks = <&clks IMX5_CLK_VPU_REFERENCE_GATE>,
 				         <&clks IMX5_CLK_VPU_GATE>;
 				clock-names = "per", "ahb";
 				resets = <&src 1>;

arch/arm/boot/dts/omap3-n900.dts

@@ -353,7 +353,7 @@
 	};
 
 	twl_power: power {
-		compatible = "ti,twl4030-power-n900";
+		compatible = "ti,twl4030-power-n900", "ti,twl4030-power-idle-osc-off";
 		ti,use_poweroff;
 	};
 };

arch/arm/boot/dts/vf610-twr.dts

@@ -168,7 +168,7 @@
 		};
 
 		pinctrl_esdhc1: esdhc1grp {
-			fsl,fsl,pins = <
+			fsl,pins = <
 				VF610_PAD_PTA24__ESDHC1_CLK	0x31ef
 				VF610_PAD_PTA25__ESDHC1_CMD	0x31ef
 				VF610_PAD_PTA26__ESDHC1_DAT0	0x31ef

arch/arm/common/edma.c

@@ -1415,14 +1415,14 @@ void edma_clear_event(unsigned channel)
 EXPORT_SYMBOL(edma_clear_event);
 
 static int edma_setup_from_hw(struct device *dev, struct edma_soc_info *pdata,
-			      struct edma *edma_cc)
+			      struct edma *edma_cc, int cc_id)
 {
 	int i;
 	u32 value, cccfg;
 	s8 (*queue_priority_map)[2];
 
 	/* Decode the eDMA3 configuration from CCCFG register */
-	cccfg = edma_read(0, EDMA_CCCFG);
+	cccfg = edma_read(cc_id, EDMA_CCCFG);
 
 	value = GET_NUM_REGN(cccfg);
 	edma_cc->num_region = BIT(value);
@@ -1436,7 +1436,8 @@ static int edma_setup_from_hw(struct device *dev, struct edma_soc_info *pdata,
 	value = GET_NUM_EVQUE(cccfg);
 	edma_cc->num_tc = value + 1;
 
-	dev_dbg(dev, "eDMA3 HW configuration (cccfg: 0x%08x):\n", cccfg);
+	dev_dbg(dev, "eDMA3 CC%d HW configuration (cccfg: 0x%08x):\n", cc_id,
+		cccfg);
 	dev_dbg(dev, "num_region: %u\n", edma_cc->num_region);
 	dev_dbg(dev, "num_channel: %u\n", edma_cc->num_channels);
 	dev_dbg(dev, "num_slot: %u\n", edma_cc->num_slots);
@@ -1655,7 +1656,7 @@ static int edma_probe(struct platform_device *pdev)
 			return -ENOMEM;
 
 		/* Get eDMA3 configuration from IP */
-		ret = edma_setup_from_hw(dev, info[j], edma_cc[j]);
+		ret = edma_setup_from_hw(dev, info[j], edma_cc[j], j);
 		if (ret)
 			return ret;
 

arch/arm/configs/bcmrpi_cutdown_defconfig

@@ -0,0 +1,503 @@
+CONFIG_EXPERIMENTAL=y
+# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_SYSVIPC=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+# CONFIG_UID16 is not set
+# CONFIG_KALLSYMS is not set
+CONFIG_EMBEDDED=y
+# CONFIG_VM_EVENT_COUNTERS is not set
+# CONFIG_COMPAT_BRK is not set
+CONFIG_SLAB=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+CONFIG_MODULE_SRCVERSION_ALL=y
+# CONFIG_BLK_DEV_BSG is not set
+CONFIG_ARCH_BCM2708=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_AEABI=y
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_CMDLINE="dwc_otg.lpm_enable=0 console=ttyAMA0,115200 kgdboc=ttyAMA0,115200 root=/dev/mmcblk0p2 rootfstype=ext3 rootwait"
+CONFIG_CPU_IDLE=y
+CONFIG_VFP=y
+CONFIG_BINFMT_MISC=m
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_XFRM_USER=y
+CONFIG_NET_KEY=m
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_RARP=y
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_LRO is not set
+# CONFIG_INET_DIAG is not set
+# CONFIG_IPV6 is not set
+CONFIG_NET_PKTGEN=m
+CONFIG_IRDA=m
+CONFIG_IRLAN=m
+CONFIG_IRCOMM=m
+CONFIG_IRDA_ULTRA=y
+CONFIG_IRDA_CACHE_LAST_LSAP=y
+CONFIG_IRDA_FAST_RR=y
+CONFIG_IRTTY_SIR=m
+CONFIG_KINGSUN_DONGLE=m
+CONFIG_KSDAZZLE_DONGLE=m
+CONFIG_KS959_DONGLE=m
+CONFIG_USB_IRDA=m
+CONFIG_SIGMATEL_FIR=m
+CONFIG_MCS_FIR=m
+CONFIG_BT=m
+CONFIG_BT_L2CAP=y
+CONFIG_BT_SCO=y
+CONFIG_BT_RFCOMM=m
+CONFIG_BT_RFCOMM_TTY=y
+CONFIG_BT_BNEP=m
+CONFIG_BT_BNEP_MC_FILTER=y
+CONFIG_BT_BNEP_PROTO_FILTER=y
+CONFIG_BT_HIDP=m
+CONFIG_BT_HCIBTUSB=m
+CONFIG_BT_HCIBCM203X=m
+CONFIG_BT_HCIBPA10X=m
+CONFIG_BT_HCIBFUSB=m
+CONFIG_BT_HCIVHCI=m
+CONFIG_BT_MRVL=m
+CONFIG_BT_MRVL_SDIO=m
+CONFIG_BT_ATH3K=m
+CONFIG_CFG80211=m
+CONFIG_MAC80211=m
+CONFIG_MAC80211_RC_PID=y
+CONFIG_MAC80211_MESH=y
+CONFIG_WIMAX=m
+CONFIG_NET_9P=m
+CONFIG_NFC=m
+CONFIG_NFC_PN533=m
+CONFIG_DEVTMPFS=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_CRYPTOLOOP=m
+CONFIG_BLK_DEV_NBD=m
+CONFIG_BLK_DEV_RAM=y
+CONFIG_CDROM_PKTCDVD=m
+CONFIG_MISC_DEVICES=y
+CONFIG_SCSI=y
+# CONFIG_SCSI_PROC_FS is not set
+CONFIG_BLK_DEV_SD=m
+CONFIG_BLK_DEV_SR=m
+CONFIG_SCSI_MULTI_LUN=y
+# CONFIG_SCSI_LOWLEVEL is not set
+CONFIG_NETDEVICES=y
+CONFIG_TUN=m
+CONFIG_PHYLIB=m
+CONFIG_MDIO_BITBANG=m
+CONFIG_NET_ETHERNET=y
+# CONFIG_NETDEV_1000 is not set
+# CONFIG_NETDEV_10000 is not set
+CONFIG_LIBERTAS_THINFIRM=m
+CONFIG_LIBERTAS_THINFIRM_USB=m
+CONFIG_AT76C50X_USB=m
+CONFIG_USB_ZD1201=m
+CONFIG_USB_NET_RNDIS_WLAN=m
+CONFIG_RTL8187=m
+CONFIG_MAC80211_HWSIM=m
+CONFIG_ATH_COMMON=m
+CONFIG_ATH9K=m
+CONFIG_ATH9K_HTC=m
+CONFIG_CARL9170=m
+CONFIG_B43=m
+CONFIG_B43LEGACY=m
+CONFIG_HOSTAP=m
+CONFIG_IWM=m
+CONFIG_LIBERTAS=m
+CONFIG_LIBERTAS_USB=m
+CONFIG_LIBERTAS_SDIO=m
+CONFIG_P54_COMMON=m
+CONFIG_P54_USB=m
+CONFIG_RT2X00=m
+CONFIG_RT2500USB=m
+CONFIG_RT73USB=m
+CONFIG_RT2800USB=m
+CONFIG_RT2800USB_RT53XX=y
+CONFIG_RTL8192CU=m
+CONFIG_WL1251=m
+CONFIG_WL12XX_MENU=m
+CONFIG_ZD1211RW=m
+CONFIG_MWIFIEX=m
+CONFIG_MWIFIEX_SDIO=m
+CONFIG_WIMAX_I2400M_USB=m
+CONFIG_USB_CATC=m
+CONFIG_USB_KAWETH=m
+CONFIG_USB_PEGASUS=m
+CONFIG_USB_RTL8150=m
+CONFIG_USB_USBNET=y
+CONFIG_USB_NET_AX8817X=m
+CONFIG_USB_NET_CDCETHER=m
+CONFIG_USB_NET_CDC_EEM=m
+CONFIG_USB_NET_DM9601=m
+CONFIG_USB_NET_SMSC75XX=m
+CONFIG_USB_NET_SMSC95XX=y
+CONFIG_USB_NET_GL620A=m
+CONFIG_USB_NET_NET1080=m
+CONFIG_USB_NET_PLUSB=m
+CONFIG_USB_NET_MCS7830=m
+CONFIG_USB_NET_CDC_SUBSET=m
+CONFIG_USB_ALI_M5632=y
+CONFIG_USB_AN2720=y
+CONFIG_USB_KC2190=y
+# CONFIG_USB_NET_ZAURUS is not set
+CONFIG_USB_NET_CX82310_ETH=m
+CONFIG_USB_NET_KALMIA=m
+CONFIG_USB_NET_INT51X1=m
+CONFIG_USB_IPHETH=m
+CONFIG_USB_SIERRA_NET=m
+CONFIG_USB_VL600=m
+CONFIG_PPP=m
+CONFIG_PPP_ASYNC=m
+CONFIG_PPP_SYNC_TTY=m
+CONFIG_PPP_DEFLATE=m
+CONFIG_PPP_BSDCOMP=m
+CONFIG_SLIP=m
+CONFIG_SLIP_COMPRESSED=y
+CONFIG_NETCONSOLE=m
+CONFIG_INPUT_POLLDEV=m
+# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
+CONFIG_INPUT_JOYDEV=m
+CONFIG_INPUT_EVDEV=m
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+CONFIG_INPUT_MISC=y
+CONFIG_INPUT_AD714X=m
+CONFIG_INPUT_ATI_REMOTE=m
+CONFIG_INPUT_ATI_REMOTE2=m
+CONFIG_INPUT_KEYSPAN_REMOTE=m
+CONFIG_INPUT_POWERMATE=m
+CONFIG_INPUT_YEALINK=m
+CONFIG_INPUT_CM109=m
+CONFIG_INPUT_UINPUT=m
+CONFIG_INPUT_GPIO_ROTARY_ENCODER=m
+CONFIG_INPUT_ADXL34X=m
+CONFIG_INPUT_CMA3000=m
+CONFIG_SERIO=m
+CONFIG_SERIO_RAW=m
+CONFIG_GAMEPORT=m
+CONFIG_GAMEPORT_NS558=m
+CONFIG_GAMEPORT_L4=m
+CONFIG_VT_HW_CONSOLE_BINDING=y
+# CONFIG_LEGACY_PTYS is not set
+# CONFIG_DEVKMEM is not set
+CONFIG_SERIAL_AMBA_PL011=y
+CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
+# CONFIG_HW_RANDOM is not set
+CONFIG_RAW_DRIVER=y
+CONFIG_GPIO_SYSFS=y
+# CONFIG_HWMON is not set
+CONFIG_WATCHDOG=y
+CONFIG_BCM2708_WDT=m
+# CONFIG_MFD_SUPPORT is not set
+CONFIG_FB=y
+CONFIG_FB_BCM2708=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_LOGO=y
+# CONFIG_LOGO_LINUX_MONO is not set
+# CONFIG_LOGO_LINUX_VGA16 is not set
+CONFIG_SOUND=y
+CONFIG_SND=m
+CONFIG_SND_SEQUENCER=m
+CONFIG_SND_SEQ_DUMMY=m
+CONFIG_SND_MIXER_OSS=m
+CONFIG_SND_PCM_OSS=m
+CONFIG_SND_SEQUENCER_OSS=y
+CONFIG_SND_HRTIMER=m
+CONFIG_SND_DUMMY=m
+CONFIG_SND_ALOOP=m
+CONFIG_SND_VIRMIDI=m
+CONFIG_SND_MTPAV=m
+CONFIG_SND_SERIAL_U16550=m
+CONFIG_SND_MPU401=m
+CONFIG_SND_BCM2835=m
+CONFIG_SND_USB_AUDIO=m
+CONFIG_SND_USB_UA101=m
+CONFIG_SND_USB_CAIAQ=m
+CONFIG_SND_USB_6FIRE=m
+CONFIG_SOUND_PRIME=m
+CONFIG_HID_PID=y
+CONFIG_USB_HIDDEV=y
+CONFIG_HID_A4TECH=m
+CONFIG_HID_ACRUX=m
+CONFIG_HID_APPLE=m
+CONFIG_HID_BELKIN=m
+CONFIG_HID_CHERRY=m
+CONFIG_HID_CHICONY=m
+CONFIG_HID_CYPRESS=m
+CONFIG_HID_DRAGONRISE=m
+CONFIG_HID_EMS_FF=m
+CONFIG_HID_ELECOM=m
+CONFIG_HID_EZKEY=m
+CONFIG_HID_HOLTEK=m
+CONFIG_HID_KEYTOUCH=m
+CONFIG_HID_KYE=m
+CONFIG_HID_UCLOGIC=m
+CONFIG_HID_WALTOP=m
+CONFIG_HID_GYRATION=m
+CONFIG_HID_TWINHAN=m
+CONFIG_HID_KENSINGTON=m
+CONFIG_HID_LCPOWER=m
+CONFIG_HID_LOGITECH=m
+CONFIG_HID_MAGICMOUSE=m
+CONFIG_HID_MICROSOFT=m
+CONFIG_HID_MONTEREY=m
+CONFIG_HID_MULTITOUCH=m
+CONFIG_HID_NTRIG=m
+CONFIG_HID_ORTEK=m
+CONFIG_HID_PANTHERLORD=m
+CONFIG_HID_PETALYNX=m
+CONFIG_HID_PICOLCD=m
+CONFIG_HID_QUANTA=m
+CONFIG_HID_ROCCAT=m
+CONFIG_HID_SAMSUNG=m
+CONFIG_HID_SONY=m
+CONFIG_HID_SPEEDLINK=m
+CONFIG_HID_SUNPLUS=m
+CONFIG_HID_GREENASIA=m
+CONFIG_HID_SMARTJOYPLUS=m
+CONFIG_HID_TOPSEED=m
+CONFIG_HID_THRUSTMASTER=m
+CONFIG_HID_WACOM=m
+CONFIG_HID_WIIMOTE=m
+CONFIG_HID_ZEROPLUS=m
+CONFIG_HID_ZYDACRON=m
+CONFIG_USB=y
+CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
+CONFIG_USB_MON=m
+CONFIG_USB_DWCOTG=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_STORAGE_REALTEK=m
+CONFIG_USB_STORAGE_DATAFAB=m
+CONFIG_USB_STORAGE_FREECOM=m
+CONFIG_USB_STORAGE_ISD200=m
+CONFIG_USB_STORAGE_USBAT=m
+CONFIG_USB_STORAGE_SDDR09=m
+CONFIG_USB_STORAGE_SDDR55=m
+CONFIG_USB_STORAGE_JUMPSHOT=m
+CONFIG_USB_STORAGE_ALAUDA=m
+CONFIG_USB_STORAGE_ONETOUCH=m
+CONFIG_USB_STORAGE_KARMA=m
+CONFIG_USB_STORAGE_CYPRESS_ATACB=m
+CONFIG_USB_STORAGE_ENE_UB6250=m
+CONFIG_USB_UAS=m
+CONFIG_USB_LIBUSUAL=y
+CONFIG_USB_MDC800=m
+CONFIG_USB_MICROTEK=m
+CONFIG_USB_SERIAL=m
+CONFIG_USB_SERIAL_GENERIC=y
+CONFIG_USB_SERIAL_AIRCABLE=m
+CONFIG_USB_SERIAL_ARK3116=m
+CONFIG_USB_SERIAL_BELKIN=m
+CONFIG_USB_SERIAL_CH341=m
+CONFIG_USB_SERIAL_WHITEHEAT=m
+CONFIG_USB_SERIAL_DIGI_ACCELEPORT=m
+CONFIG_USB_SERIAL_CP210X=m
+CONFIG_USB_SERIAL_CYPRESS_M8=m
+CONFIG_USB_SERIAL_EMPEG=m
+CONFIG_USB_SERIAL_FTDI_SIO=m
+CONFIG_USB_SERIAL_FUNSOFT=m
+CONFIG_USB_SERIAL_VISOR=m
+CONFIG_USB_SERIAL_IPAQ=m
+CONFIG_USB_SERIAL_IR=m
+CONFIG_USB_SERIAL_EDGEPORT=m
+CONFIG_USB_SERIAL_EDGEPORT_TI=m
+CONFIG_USB_SERIAL_GARMIN=m
+CONFIG_USB_SERIAL_IPW=m
+CONFIG_USB_SERIAL_IUU=m
+CONFIG_USB_SERIAL_KEYSPAN_PDA=m
+CONFIG_USB_SERIAL_KEYSPAN=m
+CONFIG_USB_SERIAL_KLSI=m
+CONFIG_USB_SERIAL_KOBIL_SCT=m
+CONFIG_USB_SERIAL_MCT_U232=m
+CONFIG_USB_SERIAL_MOS7720=m
+CONFIG_USB_SERIAL_MOS7840=m
+CONFIG_USB_SERIAL_MOTOROLA=m
+CONFIG_USB_SERIAL_NAVMAN=m
+CONFIG_USB_SERIAL_PL2303=m
+CONFIG_USB_SERIAL_OTI6858=m
+CONFIG_USB_SERIAL_QCAUX=m
+CONFIG_USB_SERIAL_QUALCOMM=m
+CONFIG_USB_SERIAL_SPCP8X5=m
+CONFIG_USB_SERIAL_HP4X=m
+CONFIG_USB_SERIAL_SAFE=m
+CONFIG_USB_SERIAL_SIEMENS_MPI=m
+CONFIG_USB_SERIAL_SIERRAWIRELESS=m
+CONFIG_USB_SERIAL_SYMBOL=m
+CONFIG_USB_SERIAL_TI=m
+CONFIG_USB_SERIAL_CYBERJACK=m
+CONFIG_USB_SERIAL_XIRCOM=m
+CONFIG_USB_SERIAL_OPTION=m
+CONFIG_USB_SERIAL_OMNINET=m
+CONFIG_USB_SERIAL_OPTICON=m
+CONFIG_USB_SERIAL_VIVOPAY_SERIAL=m
+CONFIG_USB_SERIAL_ZIO=m
+CONFIG_USB_SERIAL_SSU100=m
+CONFIG_USB_SERIAL_DEBUG=m
+CONFIG_USB_EMI62=m
+CONFIG_USB_EMI26=m
+CONFIG_USB_ADUTUX=m
+CONFIG_USB_SEVSEG=m
+CONFIG_USB_RIO500=m
+CONFIG_USB_LEGOTOWER=m
+CONFIG_USB_LCD=m
+CONFIG_USB_LED=m
+CONFIG_USB_CYPRESS_CY7C63=m
+CONFIG_USB_CYTHERM=m
+CONFIG_USB_IDMOUSE=m
+CONFIG_USB_FTDI_ELAN=m
+CONFIG_USB_APPLEDISPLAY=m
+CONFIG_USB_LD=m
+CONFIG_USB_TRANCEVIBRATOR=m
+CONFIG_USB_IOWARRIOR=m
+CONFIG_USB_TEST=m
+CONFIG_USB_ISIGHTFW=m
+CONFIG_USB_YUREX=m
+CONFIG_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_PLTFM=y
+CONFIG_MMC_SDHCI_BCM2708=y
+CONFIG_MMC_SDHCI_BCM2708_DMA=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_TRIGGER_TIMER=m
+CONFIG_LEDS_TRIGGER_HEARTBEAT=m
+CONFIG_LEDS_TRIGGER_DEFAULT_ON=m
+CONFIG_UIO=m
+CONFIG_UIO_PDRV=m
+CONFIG_UIO_PDRV_GENIRQ=m
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_EXT4_FS=y
+CONFIG_EXT4_FS_POSIX_ACL=y
+CONFIG_EXT4_FS_SECURITY=y
+CONFIG_REISERFS_FS=m
+CONFIG_REISERFS_FS_XATTR=y
+CONFIG_REISERFS_FS_POSIX_ACL=y
+CONFIG_REISERFS_FS_SECURITY=y
+CONFIG_JFS_FS=m
+CONFIG_JFS_POSIX_ACL=y
+CONFIG_JFS_SECURITY=y
+CONFIG_XFS_FS=m
+CONFIG_XFS_QUOTA=y
+CONFIG_XFS_POSIX_ACL=y
+CONFIG_XFS_RT=y
+CONFIG_GFS2_FS=m
+CONFIG_OCFS2_FS=m
+CONFIG_BTRFS_FS=m
+CONFIG_BTRFS_FS_POSIX_ACL=y
+CONFIG_NILFS2_FS=m
+CONFIG_AUTOFS4_FS=y
+CONFIG_FUSE_FS=m
+CONFIG_CUSE=m
+CONFIG_FSCACHE=y
+CONFIG_CACHEFILES=y
+CONFIG_ISO9660_FS=m
+CONFIG_JOLIET=y
+CONFIG_ZISOFS=y
+CONFIG_UDF_FS=m
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_FAT_DEFAULT_IOCHARSET="ascii"
+CONFIG_NTFS_FS=m
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
+CONFIG_CONFIGFS_FS=y
+CONFIG_SQUASHFS=m
+CONFIG_SQUASHFS_XATTR=y
+CONFIG_SQUASHFS_LZO=y
+CONFIG_SQUASHFS_XZ=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+CONFIG_NFS_V3_ACL=y
+CONFIG_NFS_V4=y
+CONFIG_ROOT_NFS=y
+CONFIG_NFS_FSCACHE=y
+CONFIG_CIFS=m
+CONFIG_CIFS_WEAK_PW_HASH=y
+CONFIG_CIFS_XATTR=y
+CONFIG_CIFS_POSIX=y
+CONFIG_9P_FS=m
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_MAC_PARTITION=y
+CONFIG_EFI_PARTITION=y
+CONFIG_NLS_DEFAULT="utf8"
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_CODEPAGE_737=m
+CONFIG_NLS_CODEPAGE_775=m
+CONFIG_NLS_CODEPAGE_850=m
+CONFIG_NLS_CODEPAGE_852=m
+CONFIG_NLS_CODEPAGE_855=m
+CONFIG_NLS_CODEPAGE_857=m
+CONFIG_NLS_CODEPAGE_860=m
+CONFIG_NLS_CODEPAGE_861=m
+CONFIG_NLS_CODEPAGE_862=m
+CONFIG_NLS_CODEPAGE_863=m
+CONFIG_NLS_CODEPAGE_864=m
+CONFIG_NLS_CODEPAGE_865=m
+CONFIG_NLS_CODEPAGE_866=m
+CONFIG_NLS_CODEPAGE_869=m
+CONFIG_NLS_CODEPAGE_936=m
+CONFIG_NLS_CODEPAGE_950=m
+CONFIG_NLS_CODEPAGE_932=m
+CONFIG_NLS_CODEPAGE_949=m
+CONFIG_NLS_CODEPAGE_874=m
+CONFIG_NLS_ISO8859_8=m
+CONFIG_NLS_CODEPAGE_1250=m
+CONFIG_NLS_CODEPAGE_1251=m
+CONFIG_NLS_ASCII=y
+CONFIG_NLS_ISO8859_1=m
+CONFIG_NLS_ISO8859_2=m
+CONFIG_NLS_ISO8859_3=m
+CONFIG_NLS_ISO8859_4=m
+CONFIG_NLS_ISO8859_5=m
+CONFIG_NLS_ISO8859_6=m
+CONFIG_NLS_ISO8859_7=m
+CONFIG_NLS_ISO8859_9=m
+CONFIG_NLS_ISO8859_13=m
+CONFIG_NLS_ISO8859_14=m
+CONFIG_NLS_ISO8859_15=m
+CONFIG_NLS_KOI8_R=m
+CONFIG_NLS_KOI8_U=m
+CONFIG_NLS_UTF8=m
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_FTRACE is not set
+# CONFIG_ARM_UNWIND is not set
+CONFIG_CRYPTO_AUTHENC=m
+CONFIG_CRYPTO_SEQIV=m
+CONFIG_CRYPTO_CBC=y
+CONFIG_CRYPTO_HMAC=y
+CONFIG_CRYPTO_XCBC=m
+CONFIG_CRYPTO_MD5=y
+CONFIG_CRYPTO_SHA1=y
+CONFIG_CRYPTO_SHA256=m
+CONFIG_CRYPTO_SHA512=m
+CONFIG_CRYPTO_TGR192=m
+CONFIG_CRYPTO_WP512=m
+CONFIG_CRYPTO_CAST5=m
+CONFIG_CRYPTO_DES=y
+CONFIG_CRYPTO_DEFLATE=m
+# CONFIG_CRYPTO_ANSI_CPRNG is not set
+# CONFIG_CRYPTO_HW is not set
+CONFIG_CRC_ITU_T=y
+CONFIG_LIBCRC32C=y
+CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_COMPAT=y
+CONFIG_I2C_CHARDEV=m
+CONFIG_I2C_HELPER_AUTO=y
+CONFIG_I2C_BCM2708=m
+CONFIG_SPI=y
+CONFIG_SPI_MASTER=y
+CONFIG_SPI_BCM2708=m

arch/arm/configs/bcmrpi_emergency_defconfig

@@ -0,0 +1,532 @@
+CONFIG_EXPERIMENTAL=y
+# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_SYSVIPC=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_BSD_PROCESS_ACCT=y
+CONFIG_BSD_PROCESS_ACCT_V3=y
+CONFIG_FHANDLE=y
+CONFIG_AUDIT=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_INITRAMFS_SOURCE="../target_fs"
+CONFIG_CGROUP_FREEZER=y
+CONFIG_CGROUP_DEVICE=y
+CONFIG_CGROUP_CPUACCT=y
+CONFIG_RESOURCE_COUNTERS=y
+CONFIG_BLK_CGROUP=y
+CONFIG_NAMESPACES=y
+CONFIG_SCHED_AUTOGROUP=y
+CONFIG_EMBEDDED=y
+# CONFIG_COMPAT_BRK is not set
+CONFIG_SLAB=y
+CONFIG_PROFILING=y
+CONFIG_OPROFILE=m
+CONFIG_KPROBES=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+CONFIG_MODULE_SRCVERSION_ALL=y
+# CONFIG_BLK_DEV_BSG is not set
+CONFIG_BLK_DEV_THROTTLING=y
+CONFIG_CFQ_GROUP_IOSCHED=y
+CONFIG_ARCH_BCM2708=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_AEABI=y
+CONFIG_SECCOMP=y
+CONFIG_CC_STACKPROTECTOR=y
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_CMDLINE="dwc_otg.lpm_enable=0 console=ttyAMA0,115200 kgdboc=ttyAMA0,115200 root=/dev/mmcblk0p2 rootfstype=ext3 rootwait"
+CONFIG_KEXEC=y
+CONFIG_CPU_IDLE=y
+CONFIG_VFP=y
+CONFIG_BINFMT_MISC=m
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_XFRM_USER=y
+CONFIG_NET_KEY=m
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_RARP=y
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_LRO is not set
+# CONFIG_INET_DIAG is not set
+# CONFIG_IPV6 is not set
+CONFIG_NET_PKTGEN=m
+CONFIG_IRDA=m
+CONFIG_IRLAN=m
+CONFIG_IRCOMM=m
+CONFIG_IRDA_ULTRA=y
+CONFIG_IRDA_CACHE_LAST_LSAP=y
+CONFIG_IRDA_FAST_RR=y
+CONFIG_IRTTY_SIR=m
+CONFIG_KINGSUN_DONGLE=m
+CONFIG_KSDAZZLE_DONGLE=m
+CONFIG_KS959_DONGLE=m
+CONFIG_USB_IRDA=m
+CONFIG_SIGMATEL_FIR=m
+CONFIG_MCS_FIR=m
+CONFIG_BT=m
+CONFIG_BT_L2CAP=y
+CONFIG_BT_SCO=y
+CONFIG_BT_RFCOMM=m
+CONFIG_BT_RFCOMM_TTY=y
+CONFIG_BT_BNEP=m
+CONFIG_BT_BNEP_MC_FILTER=y
+CONFIG_BT_BNEP_PROTO_FILTER=y
+CONFIG_BT_HIDP=m
+CONFIG_BT_HCIBTUSB=m
+CONFIG_BT_HCIBCM203X=m
+CONFIG_BT_HCIBPA10X=m
+CONFIG_BT_HCIBFUSB=m
+CONFIG_BT_HCIVHCI=m
+CONFIG_BT_MRVL=m
+CONFIG_BT_MRVL_SDIO=m
+CONFIG_BT_ATH3K=m
+CONFIG_CFG80211=m
+CONFIG_MAC80211=m
+CONFIG_MAC80211_RC_PID=y
+CONFIG_MAC80211_MESH=y
+CONFIG_WIMAX=m
+CONFIG_NET_9P=m
+CONFIG_NFC=m
+CONFIG_NFC_PN533=m
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_CRYPTOLOOP=m
+CONFIG_BLK_DEV_NBD=m
+CONFIG_BLK_DEV_RAM=y
+CONFIG_CDROM_PKTCDVD=m
+CONFIG_MISC_DEVICES=y
+CONFIG_SCSI=y
+# CONFIG_SCSI_PROC_FS is not set
+CONFIG_BLK_DEV_SD=y
+CONFIG_BLK_DEV_SR=m
+CONFIG_SCSI_MULTI_LUN=y
+# CONFIG_SCSI_LOWLEVEL is not set
+CONFIG_MD=y
+CONFIG_NETDEVICES=y
+CONFIG_TUN=m
+CONFIG_PHYLIB=m
+CONFIG_MDIO_BITBANG=m
+CONFIG_NET_ETHERNET=y
+# CONFIG_NETDEV_1000 is not set
+# CONFIG_NETDEV_10000 is not set
+CONFIG_LIBERTAS_THINFIRM=m
+CONFIG_LIBERTAS_THINFIRM_USB=m
+CONFIG_AT76C50X_USB=m
+CONFIG_USB_ZD1201=m
+CONFIG_USB_NET_RNDIS_WLAN=m
+CONFIG_RTL8187=m
+CONFIG_MAC80211_HWSIM=m
+CONFIG_ATH_COMMON=m
+CONFIG_ATH9K=m
+CONFIG_ATH9K_HTC=m
+CONFIG_CARL9170=m
+CONFIG_B43=m
+CONFIG_B43LEGACY=m
+CONFIG_HOSTAP=m
+CONFIG_IWM=m
+CONFIG_LIBERTAS=m
+CONFIG_LIBERTAS_USB=m
+CONFIG_LIBERTAS_SDIO=m
+CONFIG_P54_COMMON=m
+CONFIG_P54_USB=m
+CONFIG_RT2X00=m
+CONFIG_RT2500USB=m
+CONFIG_RT73USB=m
+CONFIG_RT2800USB=m
+CONFIG_RT2800USB_RT53XX=y
+CONFIG_RTL8192CU=m
+CONFIG_WL1251=m
+CONFIG_WL12XX_MENU=m
+CONFIG_ZD1211RW=m
+CONFIG_MWIFIEX=m
+CONFIG_MWIFIEX_SDIO=m
+CONFIG_WIMAX_I2400M_USB=m
+CONFIG_USB_CATC=m
+CONFIG_USB_KAWETH=m
+CONFIG_USB_PEGASUS=m
+CONFIG_USB_RTL8150=m
+CONFIG_USB_USBNET=y
+CONFIG_USB_NET_AX8817X=m
+CONFIG_USB_NET_CDCETHER=m
+CONFIG_USB_NET_CDC_EEM=m
+CONFIG_USB_NET_DM9601=m
+CONFIG_USB_NET_SMSC75XX=m
+CONFIG_USB_NET_SMSC95XX=y
+CONFIG_USB_NET_GL620A=m
+CONFIG_USB_NET_NET1080=m
+CONFIG_USB_NET_PLUSB=m
+CONFIG_USB_NET_MCS7830=m
+CONFIG_USB_NET_CDC_SUBSET=m
+CONFIG_USB_ALI_M5632=y
+CONFIG_USB_AN2720=y
+CONFIG_USB_KC2190=y
+# CONFIG_USB_NET_ZAURUS is not set
+CONFIG_USB_NET_CX82310_ETH=m
+CONFIG_USB_NET_KALMIA=m
+CONFIG_USB_NET_INT51X1=m
+CONFIG_USB_IPHETH=m
+CONFIG_USB_SIERRA_NET=m
+CONFIG_USB_VL600=m
+CONFIG_PPP=m
+CONFIG_PPP_ASYNC=m
+CONFIG_PPP_SYNC_TTY=m
+CONFIG_PPP_DEFLATE=m
+CONFIG_PPP_BSDCOMP=m
+CONFIG_SLIP=m
+CONFIG_SLIP_COMPRESSED=y
+CONFIG_NETCONSOLE=m
+CONFIG_INPUT_POLLDEV=m
+# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
+CONFIG_INPUT_JOYDEV=m
+CONFIG_INPUT_EVDEV=m
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+CONFIG_INPUT_MISC=y
+CONFIG_INPUT_AD714X=m
+CONFIG_INPUT_ATI_REMOTE=m
+CONFIG_INPUT_ATI_REMOTE2=m
+CONFIG_INPUT_KEYSPAN_REMOTE=m
+CONFIG_INPUT_POWERMATE=m
+CONFIG_INPUT_YEALINK=m
+CONFIG_INPUT_CM109=m
+CONFIG_INPUT_UINPUT=m
+CONFIG_INPUT_GPIO_ROTARY_ENCODER=m
+CONFIG_INPUT_ADXL34X=m
+CONFIG_INPUT_CMA3000=m
+CONFIG_SERIO=m
+CONFIG_SERIO_RAW=m
+CONFIG_GAMEPORT=m
+CONFIG_GAMEPORT_NS558=m
+CONFIG_GAMEPORT_L4=m
+CONFIG_VT_HW_CONSOLE_BINDING=y
+# CONFIG_LEGACY_PTYS is not set
+# CONFIG_DEVKMEM is not set
+CONFIG_SERIAL_AMBA_PL011=y
+CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
+# CONFIG_HW_RANDOM is not set
+CONFIG_RAW_DRIVER=y
+CONFIG_GPIO_SYSFS=y
+# CONFIG_HWMON is not set
+CONFIG_WATCHDOG=y
+CONFIG_BCM2708_WDT=m
+# CONFIG_MFD_SUPPORT is not set
+CONFIG_FB=y
+CONFIG_FB_BCM2708=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_LOGO=y
+# CONFIG_LOGO_LINUX_MONO is not set
+# CONFIG_LOGO_LINUX_VGA16 is not set
+CONFIG_SOUND=y
+CONFIG_SND=m
+CONFIG_SND_SEQUENCER=m
+CONFIG_SND_SEQ_DUMMY=m
+CONFIG_SND_MIXER_OSS=m
+CONFIG_SND_PCM_OSS=m
+CONFIG_SND_SEQUENCER_OSS=y
+CONFIG_SND_HRTIMER=m
+CONFIG_SND_DUMMY=m
+CONFIG_SND_ALOOP=m
+CONFIG_SND_VIRMIDI=m
+CONFIG_SND_MTPAV=m
+CONFIG_SND_SERIAL_U16550=m
+CONFIG_SND_MPU401=m
+CONFIG_SND_BCM2835=m
+CONFIG_SND_USB_AUDIO=m
+CONFIG_SND_USB_UA101=m
+CONFIG_SND_USB_CAIAQ=m
+CONFIG_SND_USB_6FIRE=m
+CONFIG_SOUND_PRIME=m
+CONFIG_HID_PID=y
+CONFIG_USB_HIDDEV=y
+CONFIG_HID_A4TECH=m
+CONFIG_HID_ACRUX=m
+CONFIG_HID_APPLE=m
+CONFIG_HID_BELKIN=m
+CONFIG_HID_CHERRY=m
+CONFIG_HID_CHICONY=m
+CONFIG_HID_CYPRESS=m
+CONFIG_HID_DRAGONRISE=m
+CONFIG_HID_EMS_FF=m
+CONFIG_HID_ELECOM=m
+CONFIG_HID_EZKEY=m
+CONFIG_HID_HOLTEK=m
+CONFIG_HID_KEYTOUCH=m
+CONFIG_HID_KYE=m
+CONFIG_HID_UCLOGIC=m
+CONFIG_HID_WALTOP=m
+CONFIG_HID_GYRATION=m
+CONFIG_HID_TWINHAN=m
+CONFIG_HID_KENSINGTON=m
+CONFIG_HID_LCPOWER=m
+CONFIG_HID_LOGITECH=m
+CONFIG_HID_MAGICMOUSE=m
+CONFIG_HID_MICROSOFT=m
+CONFIG_HID_MONTEREY=m
+CONFIG_HID_MULTITOUCH=m
+CONFIG_HID_NTRIG=m
+CONFIG_HID_ORTEK=m
+CONFIG_HID_PANTHERLORD=m
+CONFIG_HID_PETALYNX=m
+CONFIG_HID_PICOLCD=m
+CONFIG_HID_QUANTA=m
+CONFIG_HID_ROCCAT=m
+CONFIG_HID_SAMSUNG=m
+CONFIG_HID_SONY=m
+CONFIG_HID_SPEEDLINK=m
+CONFIG_HID_SUNPLUS=m
+CONFIG_HID_GREENASIA=m
+CONFIG_HID_SMARTJOYPLUS=m
+CONFIG_HID_TOPSEED=m
+CONFIG_HID_THRUSTMASTER=m
+CONFIG_HID_WACOM=m
+CONFIG_HID_WIIMOTE=m
+CONFIG_HID_ZEROPLUS=m
+CONFIG_HID_ZYDACRON=m
+CONFIG_USB=y
+CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
+CONFIG_USB_MON=m
+CONFIG_USB_DWCOTG=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_STORAGE_REALTEK=m
+CONFIG_USB_STORAGE_DATAFAB=m
+CONFIG_USB_STORAGE_FREECOM=m
+CONFIG_USB_STORAGE_ISD200=m
+CONFIG_USB_STORAGE_USBAT=m
+CONFIG_USB_STORAGE_SDDR09=m
+CONFIG_USB_STORAGE_SDDR55=m
+CONFIG_USB_STORAGE_JUMPSHOT=m
+CONFIG_USB_STORAGE_ALAUDA=m
+CONFIG_USB_STORAGE_ONETOUCH=m
+CONFIG_USB_STORAGE_KARMA=m
+CONFIG_USB_STORAGE_CYPRESS_ATACB=m
+CONFIG_USB_STORAGE_ENE_UB6250=m
+CONFIG_USB_UAS=y
+CONFIG_USB_LIBUSUAL=y
+CONFIG_USB_MDC800=m
+CONFIG_USB_MICROTEK=m
+CONFIG_USB_SERIAL=m
+CONFIG_USB_SERIAL_GENERIC=y
+CONFIG_USB_SERIAL_AIRCABLE=m
+CONFIG_USB_SERIAL_ARK3116=m
+CONFIG_USB_SERIAL_BELKIN=m
+CONFIG_USB_SERIAL_CH341=m
+CONFIG_USB_SERIAL_WHITEHEAT=m
+CONFIG_USB_SERIAL_DIGI_ACCELEPORT=m
+CONFIG_USB_SERIAL_CP210X=m
+CONFIG_USB_SERIAL_CYPRESS_M8=m
+CONFIG_USB_SERIAL_EMPEG=m
+CONFIG_USB_SERIAL_FTDI_SIO=m
+CONFIG_USB_SERIAL_FUNSOFT=m
+CONFIG_USB_SERIAL_VISOR=m
+CONFIG_USB_SERIAL_IPAQ=m
+CONFIG_USB_SERIAL_IR=m
+CONFIG_USB_SERIAL_EDGEPORT=m
+CONFIG_USB_SERIAL_EDGEPORT_TI=m
+CONFIG_USB_SERIAL_GARMIN=m
+CONFIG_USB_SERIAL_IPW=m
+CONFIG_USB_SERIAL_IUU=m
+CONFIG_USB_SERIAL_KEYSPAN_PDA=m
+CONFIG_USB_SERIAL_KEYSPAN=m
+CONFIG_USB_SERIAL_KLSI=m
+CONFIG_USB_SERIAL_KOBIL_SCT=m
+CONFIG_USB_SERIAL_MCT_U232=m
+CONFIG_USB_SERIAL_MOS7720=m
+CONFIG_USB_SERIAL_MOS7840=m
+CONFIG_USB_SERIAL_MOTOROLA=m
+CONFIG_USB_SERIAL_NAVMAN=m
+CONFIG_USB_SERIAL_PL2303=m
+CONFIG_USB_SERIAL_OTI6858=m
+CONFIG_USB_SERIAL_QCAUX=m
+CONFIG_USB_SERIAL_QUALCOMM=m
+CONFIG_USB_SERIAL_SPCP8X5=m
+CONFIG_USB_SERIAL_HP4X=m
+CONFIG_USB_SERIAL_SAFE=m
+CONFIG_USB_SERIAL_SIEMENS_MPI=m
+CONFIG_USB_SERIAL_SIERRAWIRELESS=m
+CONFIG_USB_SERIAL_SYMBOL=m
+CONFIG_USB_SERIAL_TI=m
+CONFIG_USB_SERIAL_CYBERJACK=m
+CONFIG_USB_SERIAL_XIRCOM=m
+CONFIG_USB_SERIAL_OPTION=m
+CONFIG_USB_SERIAL_OMNINET=m
+CONFIG_USB_SERIAL_OPTICON=m
+CONFIG_USB_SERIAL_VIVOPAY_SERIAL=m
+CONFIG_USB_SERIAL_ZIO=m
+CONFIG_USB_SERIAL_SSU100=m
+CONFIG_USB_SERIAL_DEBUG=m
+CONFIG_USB_EMI62=m
+CONFIG_USB_EMI26=m
+CONFIG_USB_ADUTUX=m
+CONFIG_USB_SEVSEG=m
+CONFIG_USB_RIO500=m
+CONFIG_USB_LEGOTOWER=m
+CONFIG_USB_LCD=m
+CONFIG_USB_LED=m
+CONFIG_USB_CYPRESS_CY7C63=m
+CONFIG_USB_CYTHERM=m
+CONFIG_USB_IDMOUSE=m
+CONFIG_USB_FTDI_ELAN=m
+CONFIG_USB_APPLEDISPLAY=m
+CONFIG_USB_LD=m
+CONFIG_USB_TRANCEVIBRATOR=m
+CONFIG_USB_IOWARRIOR=m
+CONFIG_USB_TEST=m
+CONFIG_USB_ISIGHTFW=m
+CONFIG_USB_YUREX=m
+CONFIG_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_PLTFM=y
+CONFIG_MMC_SDHCI_BCM2708=y
+CONFIG_MMC_SDHCI_BCM2708_DMA=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_TRIGGER_TIMER=m
+CONFIG_LEDS_TRIGGER_HEARTBEAT=m
+CONFIG_LEDS_TRIGGER_DEFAULT_ON=m
+CONFIG_UIO=m
+CONFIG_UIO_PDRV=m
+CONFIG_UIO_PDRV_GENIRQ=m
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_EXT4_FS=y
+CONFIG_EXT4_FS_POSIX_ACL=y
+CONFIG_EXT4_FS_SECURITY=y
+CONFIG_REISERFS_FS=m
+CONFIG_REISERFS_FS_XATTR=y
+CONFIG_REISERFS_FS_POSIX_ACL=y
+CONFIG_REISERFS_FS_SECURITY=y
+CONFIG_JFS_FS=m
+CONFIG_JFS_POSIX_ACL=y
+CONFIG_JFS_SECURITY=y
+CONFIG_JFS_STATISTICS=y
+CONFIG_XFS_FS=m
+CONFIG_XFS_QUOTA=y
+CONFIG_XFS_POSIX_ACL=y
+CONFIG_XFS_RT=y
+CONFIG_GFS2_FS=m
+CONFIG_OCFS2_FS=m
+CONFIG_BTRFS_FS=m
+CONFIG_BTRFS_FS_POSIX_ACL=y
+CONFIG_NILFS2_FS=m
+CONFIG_FANOTIFY=y
+CONFIG_AUTOFS4_FS=y
+CONFIG_FUSE_FS=m
+CONFIG_CUSE=m
+CONFIG_FSCACHE=y
+CONFIG_FSCACHE_STATS=y
+CONFIG_FSCACHE_HISTOGRAM=y
+CONFIG_CACHEFILES=y
+CONFIG_ISO9660_FS=m
+CONFIG_JOLIET=y
+CONFIG_ZISOFS=y
+CONFIG_UDF_FS=m
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_FAT_DEFAULT_IOCHARSET="ascii"
+CONFIG_NTFS_FS=m
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
+CONFIG_CONFIGFS_FS=y
+CONFIG_SQUASHFS=m
+CONFIG_SQUASHFS_XATTR=y
+CONFIG_SQUASHFS_LZO=y
+CONFIG_SQUASHFS_XZ=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+CONFIG_NFS_V3_ACL=y
+CONFIG_NFS_V4=y
+CONFIG_ROOT_NFS=y
+CONFIG_NFS_FSCACHE=y
+CONFIG_CIFS=m
+CONFIG_CIFS_WEAK_PW_HASH=y
+CONFIG_CIFS_XATTR=y
+CONFIG_CIFS_POSIX=y
+CONFIG_9P_FS=m
+CONFIG_9P_FS_POSIX_ACL=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_MAC_PARTITION=y
+CONFIG_EFI_PARTITION=y
+CONFIG_NLS_DEFAULT="utf8"
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_CODEPAGE_737=m
+CONFIG_NLS_CODEPAGE_775=m
+CONFIG_NLS_CODEPAGE_850=m
+CONFIG_NLS_CODEPAGE_852=m
+CONFIG_NLS_CODEPAGE_855=m
+CONFIG_NLS_CODEPAGE_857=m
+CONFIG_NLS_CODEPAGE_860=m
+CONFIG_NLS_CODEPAGE_861=m
+CONFIG_NLS_CODEPAGE_862=m
+CONFIG_NLS_CODEPAGE_863=m
+CONFIG_NLS_CODEPAGE_864=m
+CONFIG_NLS_CODEPAGE_865=m
+CONFIG_NLS_CODEPAGE_866=m
+CONFIG_NLS_CODEPAGE_869=m
+CONFIG_NLS_CODEPAGE_936=m
+CONFIG_NLS_CODEPAGE_950=m
+CONFIG_NLS_CODEPAGE_932=m
+CONFIG_NLS_CODEPAGE_949=m
+CONFIG_NLS_CODEPAGE_874=m
+CONFIG_NLS_ISO8859_8=m
+CONFIG_NLS_CODEPAGE_1250=m
+CONFIG_NLS_CODEPAGE_1251=m
+CONFIG_NLS_ASCII=y
+CONFIG_NLS_ISO8859_1=m
+CONFIG_NLS_ISO8859_2=m
+CONFIG_NLS_ISO8859_3=m
+CONFIG_NLS_ISO8859_4=m
+CONFIG_NLS_ISO8859_5=m
+CONFIG_NLS_ISO8859_6=m
+CONFIG_NLS_ISO8859_7=m
+CONFIG_NLS_ISO8859_9=m
+CONFIG_NLS_ISO8859_13=m
+CONFIG_NLS_ISO8859_14=m
+CONFIG_NLS_ISO8859_15=m
+CONFIG_NLS_KOI8_R=m
+CONFIG_NLS_KOI8_U=m
+CONFIG_NLS_UTF8=m
+CONFIG_PRINTK_TIME=y
+CONFIG_DETECT_HUNG_TASK=y
+CONFIG_TIMER_STATS=y
+CONFIG_DEBUG_STACK_USAGE=y
+CONFIG_DEBUG_INFO=y
+CONFIG_DEBUG_MEMORY_INIT=y
+CONFIG_BOOT_PRINTK_DELAY=y
+CONFIG_LATENCYTOP=y
+CONFIG_SYSCTL_SYSCALL_CHECK=y
+CONFIG_IRQSOFF_TRACER=y
+CONFIG_SCHED_TRACER=y
+CONFIG_STACK_TRACER=y
+CONFIG_BLK_DEV_IO_TRACE=y
+CONFIG_FUNCTION_PROFILER=y
+CONFIG_KGDB=y
+CONFIG_KGDB_KDB=y
+CONFIG_KDB_KEYBOARD=y
+CONFIG_STRICT_DEVMEM=y
+CONFIG_CRYPTO_AUTHENC=m
+CONFIG_CRYPTO_SEQIV=m
+CONFIG_CRYPTO_CBC=y
+CONFIG_CRYPTO_HMAC=y
+CONFIG_CRYPTO_XCBC=m
+CONFIG_CRYPTO_MD5=y
+CONFIG_CRYPTO_SHA1=y
+CONFIG_CRYPTO_SHA256=m
+CONFIG_CRYPTO_SHA512=m
+CONFIG_CRYPTO_TGR192=m
+CONFIG_CRYPTO_WP512=m
+CONFIG_CRYPTO_CAST5=m
+CONFIG_CRYPTO_DES=y
+CONFIG_CRYPTO_DEFLATE=m
+# CONFIG_CRYPTO_ANSI_CPRNG is not set
+# CONFIG_CRYPTO_HW is not set
+CONFIG_CRC_ITU_T=y
+CONFIG_LIBCRC32C=y

arch/arm/configs/bcmrpi_quick_defconfig

@@ -0,0 +1,197 @@
+# CONFIG_ARM_PATCH_PHYS_VIRT is not set
+CONFIG_LOCALVERSION="-quick"
+# CONFIG_LOCALVERSION_AUTO is not set
+# CONFIG_SWAP is not set
+CONFIG_SYSVIPC=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_KALLSYMS_ALL=y
+CONFIG_EMBEDDED=y
+CONFIG_PERF_EVENTS=y
+# CONFIG_COMPAT_BRK is not set
+CONFIG_SLAB=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+CONFIG_MODULE_SRCVERSION_ALL=y
+# CONFIG_BLK_DEV_BSG is not set
+CONFIG_ARCH_BCM2708=y
+CONFIG_PREEMPT=y
+CONFIG_AEABI=y
+CONFIG_UACCESS_WITH_MEMCPY=y
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_CMDLINE="dwc_otg.lpm_enable=0 console=ttyAMA0,115200 kgdboc=ttyAMA0,115200 root=/dev/mmcblk0p2 rootfstype=ext4 rootwait"
+CONFIG_CPU_FREQ=y
+CONFIG_CPU_FREQ_DEFAULT_GOV_POWERSAVE=y
+CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
+CONFIG_CPU_FREQ_GOV_USERSPACE=y
+CONFIG_CPU_FREQ_GOV_ONDEMAND=y
+CONFIG_CPU_FREQ_GOV_CONSERVATIVE=y
+CONFIG_CPU_IDLE=y
+CONFIG_VFP=y
+CONFIG_BINFMT_MISC=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_RARP=y
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_LRO is not set
+# CONFIG_INET_DIAG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_WIRELESS is not set
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_RAM=y
+CONFIG_SCSI=y
+# CONFIG_SCSI_PROC_FS is not set
+# CONFIG_SCSI_LOWLEVEL is not set
+CONFIG_NETDEVICES=y
+# CONFIG_NET_VENDOR_BROADCOM is not set
+# CONFIG_NET_VENDOR_CIRRUS is not set
+# CONFIG_NET_VENDOR_FARADAY is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_WIZNET is not set
+CONFIG_USB_USBNET=y
+# CONFIG_USB_NET_AX8817X is not set
+# CONFIG_USB_NET_CDCETHER is not set
+# CONFIG_USB_NET_CDC_NCM is not set
+CONFIG_USB_NET_SMSC95XX=y
+# CONFIG_USB_NET_NET1080 is not set
+# CONFIG_USB_NET_CDC_SUBSET is not set
+# CONFIG_USB_NET_ZAURUS is not set
+# CONFIG_WLAN is not set
+# CONFIG_INPUT_MOUSEDEV is not set
+CONFIG_INPUT_EVDEV=y
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_SERIO is not set
+CONFIG_VT_HW_CONSOLE_BINDING=y
+# CONFIG_LEGACY_PTYS is not set
+# CONFIG_DEVKMEM is not set
+CONFIG_SERIAL_AMBA_PL011=y
+CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
+CONFIG_TTY_PRINTK=y
+CONFIG_HW_RANDOM=y
+CONFIG_HW_RANDOM_BCM2708=y
+CONFIG_RAW_DRIVER=y
+CONFIG_THERMAL=y
+CONFIG_THERMAL_BCM2835=y
+CONFIG_WATCHDOG=y
+CONFIG_BCM2708_WDT=y
+CONFIG_REGULATOR=y
+CONFIG_REGULATOR_DEBUG=y
+CONFIG_REGULATOR_FIXED_VOLTAGE=y
+CONFIG_REGULATOR_VIRTUAL_CONSUMER=y
+CONFIG_REGULATOR_USERSPACE_CONSUMER=y
+CONFIG_FB=y
+CONFIG_FB_BCM2708=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_LOGO=y
+# CONFIG_LOGO_LINUX_MONO is not set
+# CONFIG_LOGO_LINUX_VGA16 is not set
+CONFIG_SOUND=y
+CONFIG_SND=y
+CONFIG_SND_BCM2835=y
+# CONFIG_SND_USB is not set
+CONFIG_USB=y
+CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
+CONFIG_USB_DWCOTG=y
+CONFIG_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_PLTFM=y
+CONFIG_MMC_SDHCI_BCM2708=y
+CONFIG_MMC_SDHCI_BCM2708_DMA=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_TRIGGERS=y
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_EXT4_FS=y
+CONFIG_EXT4_FS_POSIX_ACL=y
+CONFIG_EXT4_FS_SECURITY=y
+CONFIG_AUTOFS4_FS=y
+CONFIG_FSCACHE=y
+CONFIG_CACHEFILES=y
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_FAT_DEFAULT_IOCHARSET="ascii"
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
+CONFIG_CONFIGFS_FS=y
+# CONFIG_MISC_FILESYSTEMS is not set
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3_ACL=y
+CONFIG_NFS_V4=y
+CONFIG_ROOT_NFS=y
+CONFIG_NFS_FSCACHE=y
+CONFIG_NLS_DEFAULT="utf8"
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_CODEPAGE_737=y
+CONFIG_NLS_CODEPAGE_775=y
+CONFIG_NLS_CODEPAGE_850=y
+CONFIG_NLS_CODEPAGE_852=y
+CONFIG_NLS_CODEPAGE_855=y
+CONFIG_NLS_CODEPAGE_857=y
+CONFIG_NLS_CODEPAGE_860=y
+CONFIG_NLS_CODEPAGE_861=y
+CONFIG_NLS_CODEPAGE_862=y
+CONFIG_NLS_CODEPAGE_863=y
+CONFIG_NLS_CODEPAGE_864=y
+CONFIG_NLS_CODEPAGE_865=y
+CONFIG_NLS_CODEPAGE_866=y
+CONFIG_NLS_CODEPAGE_869=y
+CONFIG_NLS_CODEPAGE_936=y
+CONFIG_NLS_CODEPAGE_950=y
+CONFIG_NLS_CODEPAGE_932=y
+CONFIG_NLS_CODEPAGE_949=y
+CONFIG_NLS_CODEPAGE_874=y
+CONFIG_NLS_ISO8859_8=y
+CONFIG_NLS_CODEPAGE_1250=y
+CONFIG_NLS_CODEPAGE_1251=y
+CONFIG_NLS_ASCII=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_NLS_ISO8859_2=y
+CONFIG_NLS_ISO8859_3=y
+CONFIG_NLS_ISO8859_4=y
+CONFIG_NLS_ISO8859_5=y
+CONFIG_NLS_ISO8859_6=y
+CONFIG_NLS_ISO8859_7=y
+CONFIG_NLS_ISO8859_9=y
+CONFIG_NLS_ISO8859_13=y
+CONFIG_NLS_ISO8859_14=y
+CONFIG_NLS_ISO8859_15=y
+CONFIG_NLS_UTF8=y
+CONFIG_PRINTK_TIME=y
+CONFIG_DEBUG_FS=y
+CONFIG_DETECT_HUNG_TASK=y
+# CONFIG_DEBUG_PREEMPT is not set
+# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_FTRACE is not set
+CONFIG_KGDB=y
+CONFIG_KGDB_KDB=y
+# CONFIG_ARM_UNWIND is not set
+CONFIG_CRYPTO_CBC=y
+CONFIG_CRYPTO_HMAC=y
+CONFIG_CRYPTO_MD5=y
+CONFIG_CRYPTO_SHA1=y
+CONFIG_CRYPTO_DES=y
+# CONFIG_CRYPTO_ANSI_CPRNG is not set
+# CONFIG_CRYPTO_HW is not set
+CONFIG_CRC_ITU_T=y
+CONFIG_LIBCRC32C=y

arch/arm/include/asm/cacheflush.h

@@ -472,7 +472,6 @@ static inline void __sync_cache_range_r(volatile void *p, size_t size)
 	"mcr	p15, 0, r0, c1, c0, 0	@ set SCTLR \n\t" \
 	"isb	\n\t" \
 	"bl	v7_flush_dcache_"__stringify(level)" \n\t" \
-	"clrex	\n\t" \
 	"mrc	p15, 0, r0, c1, c0, 1	@ get ACTLR \n\t" \
 	"bic	r0, r0, #(1 << 6)	@ disable local coherency \n\t" \
 	"mcr	p15, 0, r0, c1, c0, 1	@ set ACTLR \n\t" \

arch/arm/include/asm/dma-mapping.h

@@ -58,37 +58,21 @@ static inline int dma_set_mask(struct device *dev, u64 mask)
 #ifndef __arch_pfn_to_dma
 static inline dma_addr_t pfn_to_dma(struct device *dev, unsigned long pfn)
 {
-	if (dev)
-		pfn -= dev->dma_pfn_offset;
 	return (dma_addr_t)__pfn_to_bus(pfn);
 }
 
 static inline unsigned long dma_to_pfn(struct device *dev, dma_addr_t addr)
 {
-	unsigned long pfn = __bus_to_pfn(addr);
-
-	if (dev)
-		pfn += dev->dma_pfn_offset;
-
-	return pfn;
+	return __bus_to_pfn(addr);
 }
 
 static inline void *dma_to_virt(struct device *dev, dma_addr_t addr)
 {
-	if (dev) {
-		unsigned long pfn = dma_to_pfn(dev, addr);
-
-		return phys_to_virt(__pfn_to_phys(pfn));
-	}
-
 	return (void *)__bus_to_virt((unsigned long)addr);
 }
 
 static inline dma_addr_t virt_to_dma(struct device *dev, void *addr)
 {
-	if (dev)
-		return pfn_to_dma(dev, virt_to_pfn(addr));
-
 	return (dma_addr_t)__virt_to_bus((unsigned long)(addr));
 }
 

arch/arm/include/asm/irqflags.h

@@ -145,12 +145,22 @@ static inline unsigned long arch_local_save_flags(void)
 }
 
 /*
- * restore saved IRQ & FIQ state
+ * restore saved IRQ state
  */
 static inline void arch_local_irq_restore(unsigned long flags)
 {
+	unsigned long temp = 0;
+	flags &= ~(1 << 6);
 	asm volatile (
-		"	msr	" IRQMASK_REG_NAME_W ", %0	@ local_irq_restore"
+		" mrs %0, cpsr"
+		: "=r" (temp)
+		:
+		: "memory", "cc");
+		/* Preserve FIQ bit */
+		temp &= (1 << 6);
+		flags = flags | temp;
+	asm volatile (
+		"    msr    cpsr_c, %0    @ local_irq_restore"
 		:
 		: "r" (flags)
 		: "memory", "cc");

arch/arm/include/asm/tls.h

@@ -1,6 +1,9 @@
 #ifndef __ASMARM_TLS_H
 #define __ASMARM_TLS_H
 
+#include <linux/compiler.h>
+#include <asm/thread_info.h>
+
 #ifdef __ASSEMBLY__
 #include <asm/asm-offsets.h>
 	.macro switch_tls_none, base, tp, tpuser, tmp1, tmp2
@@ -50,6 +53,49 @@
 #endif
 
 #ifndef __ASSEMBLY__
+
+static inline void set_tls(unsigned long val)
+{
+	struct thread_info *thread;
+
+	thread = current_thread_info();
+
+	thread->tp_value[0] = val;
+
+	/*
+	 * This code runs with preemption enabled and therefore must
+	 * be reentrant with respect to switch_tls.
+	 *
+	 * We need to ensure ordering between the shadow state and the
+	 * hardware state, so that we don't corrupt the hardware state
+	 * with a stale shadow state during context switch.
+	 *
+	 * If we're preempted here, switch_tls will load TPIDRURO from
+	 * thread_info upon resuming execution and the following mcr
+	 * is merely redundant.
+	 */
+	barrier();
+
+	if (!tls_emu) {
+		if (has_tls_reg) {
+			asm("mcr p15, 0, %0, c13, c0, 3"
+			    : : "r" (val));
+		} else {
+#ifdef CONFIG_KUSER_HELPERS
+			/*
+			 * User space must never try to access this
+			 * directly.  Expect your app to break
+			 * eventually if you do so.  The user helper
+			 * at 0xffff0fe0 must be used instead.  (see
+			 * entry-armv.S for details)
+			 */
+			*((unsigned int *)0xffff0ff0) = val;
+#endif
+		}
+
+	}
+}
+
 static inline unsigned long get_tpuser(void)
 {
 	unsigned long reg = 0;
@@ -59,5 +105,23 @@ static inline unsigned long get_tpuser(void)
 
 	return reg;
 }
+
+static inline void set_tpuser(unsigned long val)
+{
+	/* Since TPIDRURW is fully context-switched (unlike TPIDRURO),
+	 * we need not update thread_info.
+	 */
+	if (has_tls_reg && !tls_emu) {
+		asm("mcr p15, 0, %0, c13, c0, 2"
+		    : : "r" (val));
+	}
+}
+
+static inline void flush_tls(void)
+{
+	set_tls(0);
+	set_tpuser(0);
+}
+
 #endif
 #endif	/* __ASMARM_TLS_H */

arch/arm/include/asm/unistd.h

@@ -15,7 +15,17 @@
 
 #include <uapi/asm/unistd.h>
 
+/*
+ * This may need to be greater than __NR_last_syscall+1 in order to
+ * account for the padding in the syscall table
+ */
 #define __NR_syscalls  (384)
+
+/*
+ * *NOTE*: This is a ghost syscall private to the kernel.  Only the
+ * __kuser_cmpxchg code in entry-armv.S should be aware of its
+ * existence.  Don't ever use this from user code.
+ */
 #define __ARM_NR_cmpxchg		(__ARM_NR_BASE+0x00fff0)
 
 #define __ARCH_WANT_STAT64

arch/arm/include/uapi/asm/unistd.h

@@ -410,11 +410,6 @@
 #define __NR_sched_getattr		(__NR_SYSCALL_BASE+381)
 #define __NR_renameat2			(__NR_SYSCALL_BASE+382)
 
-/*
- * This may need to be greater than __NR_last_syscall+1 in order to
- * account for the padding in the syscall table
- */
-
 /*
  * The following SWIs are ARM private.
  */
@@ -425,12 +420,6 @@
 #define __ARM_NR_usr32			(__ARM_NR_BASE+4)
 #define __ARM_NR_set_tls		(__ARM_NR_BASE+5)
 
-/*
- * *NOTE*: This is a ghost syscall private to the kernel.  Only the
- * __kuser_cmpxchg code in entry-armv.S should be aware of its
- * existence.  Don't ever use this from user code.
- */
-
 /*
  * The following syscalls are obsolete and no longer available for EABI.
  */

arch/arm/kernel/entry-header.S

@@ -208,26 +208,21 @@
 #endif
 	.endif
 	msr	spsr_cxsf, \rpsr
-#if defined(CONFIG_CPU_V6)
-	ldr	r0, [sp]
-	strex	r1, r2, [sp]			@ clear the exclusive monitor
-	ldmib	sp, {r1 - pc}^			@ load r1 - pc, cpsr
-#elif defined(CONFIG_CPU_32v6K)
-	clrex					@ clear the exclusive monitor
-	ldmia	sp, {r0 - pc}^			@ load r0 - pc, cpsr
-#else
-	ldmia	sp, {r0 - pc}^			@ load r0 - pc, cpsr
+#if defined(CONFIG_CPU_V6) || defined(CONFIG_CPU_32v6K)
+	@ We must avoid clrex due to Cortex-A15 erratum #830321
+	sub	r0, sp, #4			@ uninhabited address
+	strex	r1, r2, [r0]			@ clear the exclusive monitor
 #endif
+	ldmia	sp, {r0 - pc}^			@ load r0 - pc, cpsr
 	.endm
 
 	.macro	restore_user_regs, fast = 0, offset = 0
 	ldr	r1, [sp, #\offset + S_PSR]	@ get calling cpsr
 	ldr	lr, [sp, #\offset + S_PC]!	@ get pc
 	msr	spsr_cxsf, r1			@ save in spsr_svc
-#if defined(CONFIG_CPU_V6)
+#if defined(CONFIG_CPU_V6) || defined(CONFIG_CPU_32v6K)
+	@ We must avoid clrex due to Cortex-A15 erratum #830321
 	strex	r1, r2, [sp]			@ clear the exclusive monitor
-#elif defined(CONFIG_CPU_32v6K)
-	clrex					@ clear the exclusive monitor
 #endif
 	.if	\fast
 	ldmdb	sp, {r1 - lr}^			@ get calling r1 - lr
@@ -267,7 +262,10 @@
 	.endif
 	ldr	lr, [sp, #S_SP]			@ top of the stack
 	ldrd	r0, r1, [sp, #S_LR]		@ calling lr and pc
-	clrex					@ clear the exclusive monitor
+
+	@ We must avoid clrex due to Cortex-A15 erratum #830321
+	strex	r2, r1, [sp, #S_LR]		@ clear the exclusive monitor
+
 	stmdb	lr!, {r0, r1, \rpsr}		@ calling lr and rfe context
 	ldmia	sp, {r0 - r12}
 	mov	sp, lr
@@ -288,13 +286,16 @@
 	.endm
 #else	/* ifdef CONFIG_CPU_V7M */
 	.macro	restore_user_regs, fast = 0, offset = 0
-	clrex					@ clear the exclusive monitor
 	mov	r2, sp
 	load_user_sp_lr r2, r3, \offset + S_SP	@ calling sp, lr
 	ldr	r1, [sp, #\offset + S_PSR]	@ get calling cpsr
 	ldr	lr, [sp, #\offset + S_PC]	@ get pc
 	add	sp, sp, #\offset + S_SP
 	msr	spsr_cxsf, r1			@ save in spsr_svc
+
+	@ We must avoid clrex due to Cortex-A15 erratum #830321
+	strex	r1, r2, [sp]			@ clear the exclusive monitor
+
 	.if	\fast
 	ldmdb	sp, {r1 - r12}			@ get calling r1 - r12
 	.else

arch/arm/kernel/fiqasm.S

@@ -47,3 +47,7 @@ ENTRY(__get_fiq_regs)
 	mov	r0, r0		@ avoid hazard prior to ARMv4
 	mov	pc, lr
 ENDPROC(__get_fiq_regs)
+
+ENTRY(__FIQ_Branch)
+	mov pc, r8
+ENDPROC(__FIQ_Branch)

arch/arm/kernel/irq.c

@@ -175,7 +175,7 @@ static bool migrate_one_irq(struct irq_desc *desc)
 	c = irq_data_get_irq_chip(d);
 	if (!c->irq_set_affinity)
 		pr_debug("IRQ%u: unable to set affinity\n", d->irq);
-	else if (c->irq_set_affinity(d, affinity, true) == IRQ_SET_MASK_OK && ret)
+	else if (c->irq_set_affinity(d, affinity, false) == IRQ_SET_MASK_OK && ret)
 		cpumask_copy(d->affinity, affinity);
 
 	return ret;

arch/arm/kernel/perf_event_cpu.c

@@ -76,21 +76,15 @@ static struct pmu_hw_events *cpu_pmu_get_cpu_events(void)
 
 static void cpu_pmu_enable_percpu_irq(void *data)
 {
-	struct arm_pmu *cpu_pmu = data;
-	struct platform_device *pmu_device = cpu_pmu->plat_device;
-	int irq = platform_get_irq(pmu_device, 0);
+	int irq = *(int *)data;
 
 	enable_percpu_irq(irq, IRQ_TYPE_NONE);
-	cpumask_set_cpu(smp_processor_id(), &cpu_pmu->active_irqs);
 }
 
 static void cpu_pmu_disable_percpu_irq(void *data)
 {
-	struct arm_pmu *cpu_pmu = data;
-	struct platform_device *pmu_device = cpu_pmu->plat_device;
-	int irq = platform_get_irq(pmu_device, 0);
+	int irq = *(int *)data;
 
-	cpumask_clear_cpu(smp_processor_id(), &cpu_pmu->active_irqs);
 	disable_percpu_irq(irq);
 }
 
@@ -103,7 +97,7 @@ static void cpu_pmu_free_irq(struct arm_pmu *cpu_pmu)
 
 	irq = platform_get_irq(pmu_device, 0);
 	if (irq >= 0 && irq_is_percpu(irq)) {
-		on_each_cpu(cpu_pmu_disable_percpu_irq, cpu_pmu, 1);
+		on_each_cpu(cpu_pmu_disable_percpu_irq, &irq, 1);
 		free_percpu_irq(irq, &percpu_pmu);
 	} else {
 		for (i = 0; i < irqs; ++i) {
@@ -138,7 +132,7 @@ static int cpu_pmu_request_irq(struct arm_pmu *cpu_pmu, irq_handler_t handler)
 				irq);
 			return err;
 		}
-		on_each_cpu(cpu_pmu_enable_percpu_irq, cpu_pmu, 1);
+		on_each_cpu(cpu_pmu_enable_percpu_irq, &irq, 1);
 	} else {
 		for (i = 0; i < irqs; ++i) {
 			err = 0;

arch/arm/kernel/perf_event_v7.c

@@ -157,6 +157,7 @@ static const unsigned armv7_a8_perf_map[PERF_COUNT_HW_MAX] = {
 	[PERF_COUNT_HW_BUS_CYCLES]		= HW_OP_UNSUPPORTED,
 	[PERF_COUNT_HW_STALLED_CYCLES_FRONTEND]	= ARMV7_A8_PERFCTR_STALL_ISIDE,
 	[PERF_COUNT_HW_STALLED_CYCLES_BACKEND]	= HW_OP_UNSUPPORTED,
+	[PERF_COUNT_HW_REF_CPU_CYCLES]	= HW_OP_UNSUPPORTED,
 };
 
 static const unsigned armv7_a8_perf_cache_map[PERF_COUNT_HW_CACHE_MAX]
@@ -281,6 +282,7 @@ static const unsigned armv7_a9_perf_map[PERF_COUNT_HW_MAX] = {
 	[PERF_COUNT_HW_BUS_CYCLES]		= HW_OP_UNSUPPORTED,
 	[PERF_COUNT_HW_STALLED_CYCLES_FRONTEND]	= ARMV7_A9_PERFCTR_STALL_ICACHE,
 	[PERF_COUNT_HW_STALLED_CYCLES_BACKEND]	= ARMV7_A9_PERFCTR_STALL_DISPATCH,
+	[PERF_COUNT_HW_REF_CPU_CYCLES]	= HW_OP_UNSUPPORTED,
 };
 
 static const unsigned armv7_a9_perf_cache_map[PERF_COUNT_HW_CACHE_MAX]
@@ -405,6 +407,7 @@ static const unsigned armv7_a5_perf_map[PERF_COUNT_HW_MAX] = {
 	[PERF_COUNT_HW_BUS_CYCLES]		= HW_OP_UNSUPPORTED,
 	[PERF_COUNT_HW_STALLED_CYCLES_FRONTEND]	= HW_OP_UNSUPPORTED,
 	[PERF_COUNT_HW_STALLED_CYCLES_BACKEND]	= HW_OP_UNSUPPORTED,
+	[PERF_COUNT_HW_REF_CPU_CYCLES] = HW_OP_UNSUPPORTED,
 };
 
 static const unsigned armv7_a5_perf_cache_map[PERF_COUNT_HW_CACHE_MAX]
@@ -527,6 +530,7 @@ static const unsigned armv7_a15_perf_map[PERF_COUNT_HW_MAX] = {
 	[PERF_COUNT_HW_BUS_CYCLES]		= ARMV7_PERFCTR_BUS_CYCLES,
 	[PERF_COUNT_HW_STALLED_CYCLES_FRONTEND]	= HW_OP_UNSUPPORTED,
 	[PERF_COUNT_HW_STALLED_CYCLES_BACKEND]	= HW_OP_UNSUPPORTED,
+	[PERF_COUNT_HW_REF_CPU_CYCLES] = HW_OP_UNSUPPORTED,
 };
 
 static const unsigned armv7_a15_perf_cache_map[PERF_COUNT_HW_CACHE_MAX]
@@ -651,6 +655,7 @@ static const unsigned armv7_a7_perf_map[PERF_COUNT_HW_MAX] = {
 	[PERF_COUNT_HW_BUS_CYCLES]		= ARMV7_PERFCTR_BUS_CYCLES,
 	[PERF_COUNT_HW_STALLED_CYCLES_FRONTEND]	= HW_OP_UNSUPPORTED,
 	[PERF_COUNT_HW_STALLED_CYCLES_BACKEND]	= HW_OP_UNSUPPORTED,
+	[PERF_COUNT_HW_REF_CPU_CYCLES] = HW_OP_UNSUPPORTED,
 };
 
 static const unsigned armv7_a7_perf_cache_map[PERF_COUNT_HW_CACHE_MAX]

arch/arm/kernel/process.c

@@ -171,6 +171,16 @@ void arch_cpu_idle_dead(void)
 }
 #endif
 
+char bcm2708_reboot_mode = 'h';
+
+int __init reboot_setup(char *str)
+{
+	bcm2708_reboot_mode = str[0];
+	return 1;
+}
+
+__setup("reboot=", reboot_setup);
+
 /*
  * Called by kexec, immediately prior to machine_kexec().
  *
@@ -334,6 +344,8 @@ void flush_thread(void)
 	memset(&tsk->thread.debug, 0, sizeof(struct debug_info));
 	memset(&thread->fpstate, 0, sizeof(union fp_state));
 
+	flush_tls();
+
 	thread_notify(THREAD_NOTIFY_FLUSH, thread);
 }
 

arch/arm/kernel/thumbee.c

@@ -45,7 +45,7 @@ static int thumbee_notifier(struct notifier_block *self, unsigned long cmd, void
 
 	switch (cmd) {
 	case THREAD_NOTIFY_FLUSH:
-		thread->thumbee_state = 0;
+		teehbr_write(0);
 		break;
 	case THREAD_NOTIFY_SWITCH:
 		current_thread_info()->thumbee_state = teehbr_read();

arch/arm/kernel/traps.c

@@ -579,7 +579,6 @@ do_cache_op(unsigned long start, unsigned long end, int flags)
 #define NR(x) ((__ARM_NR_##x) - __ARM_NR_BASE)
 asmlinkage int arm_syscall(int no, struct pt_regs *regs)
 {
-	struct thread_info *thread = current_thread_info();
 	siginfo_t info;
 
 	if ((no >> 16) != (__ARM_NR_BASE>> 16))
@@ -630,21 +629,7 @@ asmlinkage int arm_syscall(int no, struct pt_regs *regs)
 		return regs->ARM_r0;
 
 	case NR(set_tls):
-		thread->tp_value[0] = regs->ARM_r0;
-		if (tls_emu)
-			return 0;
-		if (has_tls_reg) {
-			asm ("mcr p15, 0, %0, c13, c0, 3"
-				: : "r" (regs->ARM_r0));
-		} else {
-			/*
-			 * User space must never try to access this directly.
-			 * Expect your app to break eventually if you do so.
-			 * The user helper at 0xffff0fe0 must be used instead.
-			 * (see entry-armv.S for details)
-			 */
-			*((unsigned int *)0xffff0ff0) = regs->ARM_r0;
-		}
+		set_tls(regs->ARM_r0);
 		return 0;
 
 #ifdef CONFIG_NEEDS_SYSCALL_FOR_CMPXCHG

arch/arm/kvm/handle_exit.c

@@ -93,6 +93,8 @@ static int kvm_handle_wfx(struct kvm_vcpu *vcpu, struct kvm_run *run)
 	else
 		kvm_vcpu_block(vcpu);
 
+	kvm_skip_instr(vcpu, kvm_vcpu_trap_il_is32bit(vcpu));
+
 	return 1;
 }
 

arch/arm/kvm/init.S

@@ -98,6 +98,10 @@ __do_hyp_init:
 	mrc	p15, 0, r0, c10, c2, 1
 	mcr	p15, 4, r0, c10, c2, 1
 
+	@ Invalidate the stale TLBs from Bootloader
+	mcr	p15, 4, r0, c8, c7, 0	@ TLBIALLH
+	dsb	ish
+
 	@ Set the HSCTLR to:
 	@  - ARM/THUMB exceptions: Kernel config (Thumb-2 kernel)
 	@  - Endianness: Kernel config

arch/arm/mach-bcm2708/Kconfig

@@ -0,0 +1,52 @@
+menu "Broadcom BCM2708 Implementations"
+	depends on ARCH_BCM2708
+
+config MACH_BCM2708
+	bool "Broadcom BCM2708 Development Platform"
+	select NEED_MACH_MEMORY_H
+	select NEED_MACH_IO_H
+	select CPU_V6
+	help
+	  Include support for the Broadcom(R) BCM2708 platform.
+
+config BCM2708_DT
+	bool "BCM2708 Device Tree support"
+	depends on MACH_BCM2708
+	default n
+	select USE_OF
+	select PINCTRL
+	select PINCTRL_BCM2708
+	select BCM2708_GPIO
+	help
+	  Enable Device Tree support for BCM2708
+
+config BCM2708_GPIO
+	bool "BCM2708 gpio support"
+	depends on MACH_BCM2708
+	select ARCH_REQUIRE_GPIOLIB
+        default y
+	help
+	  Include support for the Broadcom(R) BCM2708 gpio.
+
+config BCM2708_VCMEM
+	bool "Videocore Memory"
+	depends on MACH_BCM2708
+        default y
+        help
+          Helper for videocore memory access and total size allocation.
+
+config BCM2708_NOL2CACHE
+	bool "Videocore L2 cache disable"
+	depends on MACH_BCM2708
+        default n
+        help
+          Do not allow ARM to use GPU's L2 cache. Requires disable_l2cache in config.txt.
+
+config BCM2708_SPIDEV
+	bool "Bind spidev to SPI0 master"
+	depends on MACH_BCM2708 && !USE_OF
+	depends on SPI
+	default y
+	help
+	  Binds spidev driver to the SPI0 master
+endmenu

arch/arm/mach-bcm2708/Makefile

@@ -0,0 +1,7 @@
+#
+# Makefile for the linux kernel.
+#
+
+obj-$(CONFIG_MACH_BCM2708) 	+= bcm2708.o armctrl.o vcio.o power.o dma.o
+obj-$(CONFIG_BCM2708_GPIO)	+= bcm2708_gpio.o
+obj-$(CONFIG_BCM2708_VCMEM)	+= vc_mem.o

arch/arm/mach-bcm2708/Makefile.boot

@@ -0,0 +1,3 @@
+   zreladdr-y	:= 0x00008000
+params_phys-y	:= 0x00000100
+initrd_phys-y	:= 0x00800000

arch/arm/mach-bcm2708/armctrl.c

@@ -0,0 +1,316 @@
+/*
+ *  linux/arch/arm/mach-bcm2708/armctrl.c
+ *
+ *  Copyright (C) 2010 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+#include <linux/init.h>
+#include <linux/list.h>
+#include <linux/io.h>
+#include <linux/version.h>
+#include <linux/syscore_ops.h>
+#include <linux/interrupt.h>
+#include <linux/irqdomain.h>
+#include <linux/of.h>
+
+#include <asm/mach/irq.h>
+#include <mach/hardware.h>
+#include "armctrl.h"
+
+/* For support of kernels >= 3.0 assume only one VIC for now*/
+static unsigned int remap_irqs[(INTERRUPT_ARASANSDIO + 1) - INTERRUPT_JPEG] = {
+	INTERRUPT_VC_JPEG,
+	INTERRUPT_VC_USB,
+	INTERRUPT_VC_3D,
+	INTERRUPT_VC_DMA2,
+	INTERRUPT_VC_DMA3,
+	INTERRUPT_VC_I2C,
+	INTERRUPT_VC_SPI,
+	INTERRUPT_VC_I2SPCM,
+	INTERRUPT_VC_SDIO,
+	INTERRUPT_VC_UART,
+	INTERRUPT_VC_ARASANSDIO
+};
+
+static void armctrl_mask_irq(struct irq_data *d)
+{
+	static const unsigned int disables[4] = {
+		ARM_IRQ_DIBL1,
+		ARM_IRQ_DIBL2,
+		ARM_IRQ_DIBL3,
+		0
+	};
+
+	if (d->irq >= FIQ_START) {
+		writel(0, __io_address(ARM_IRQ_FAST));
+	} else {
+		unsigned int data = (unsigned int)irq_get_chip_data(d->irq);
+		writel(1 << (data & 0x1f), __io_address(disables[(data >> 5) & 0x3]));
+	}
+}
+
+static void armctrl_unmask_irq(struct irq_data *d)
+{
+	static const unsigned int enables[4] = {
+		ARM_IRQ_ENBL1,
+		ARM_IRQ_ENBL2,
+		ARM_IRQ_ENBL3,
+		0
+	};
+
+	if (d->irq >= FIQ_START) {
+		unsigned int data =
+		    (unsigned int)irq_get_chip_data(d->irq) - FIQ_START;
+		writel(0x80 | data, __io_address(ARM_IRQ_FAST));
+	} else {
+		unsigned int data = (unsigned int)irq_get_chip_data(d->irq);
+		writel(1 << (data & 0x1f), __io_address(enables[(data >> 5) & 0x3]));
+	}
+}
+
+#ifdef CONFIG_OF
+
+#define NR_IRQS_BANK0           21
+#define NR_BANKS                3 + 1 /* bank 3 is used for GPIO interrupts */
+#define IRQS_PER_BANK           32
+
+/* from drivers/irqchip/irq-bcm2835.c */
+static int armctrl_xlate(struct irq_domain *d, struct device_node *ctrlr,
+        const u32 *intspec, unsigned int intsize,
+        unsigned long *out_hwirq, unsigned int *out_type)
+{
+        if (WARN_ON(intsize != 2))
+                return -EINVAL;
+
+        if (WARN_ON(intspec[0] >= NR_BANKS))
+                return -EINVAL;
+
+        if (WARN_ON(intspec[1] >= IRQS_PER_BANK))
+                return -EINVAL;
+
+        if (WARN_ON(intspec[0] == 0 && intspec[1] >= NR_IRQS_BANK0))
+                return -EINVAL;
+
+	if (intspec[0] == 0)
+		*out_hwirq = ARM_IRQ0_BASE + intspec[1];
+	else if (intspec[0] == 1)
+		*out_hwirq = ARM_IRQ1_BASE + intspec[1];
+	else if (intspec[0] == 2)
+		*out_hwirq = ARM_IRQ2_BASE + intspec[1];
+	else
+		*out_hwirq = GPIO_IRQ_START + intspec[1];
+
+	/* reverse remap_irqs[] */
+	switch (*out_hwirq) {
+	case INTERRUPT_VC_JPEG:
+		*out_hwirq = INTERRUPT_JPEG;
+		break;
+	case INTERRUPT_VC_USB:
+		*out_hwirq = INTERRUPT_USB;
+		break;
+	case INTERRUPT_VC_3D:
+		*out_hwirq = INTERRUPT_3D;
+		break;
+	case INTERRUPT_VC_DMA2:
+		*out_hwirq = INTERRUPT_DMA2;
+		break;
+	case INTERRUPT_VC_DMA3:
+		*out_hwirq = INTERRUPT_DMA3;
+		break;
+	case INTERRUPT_VC_I2C:
+		*out_hwirq = INTERRUPT_I2C;
+		break;
+	case INTERRUPT_VC_SPI:
+		*out_hwirq = INTERRUPT_SPI;
+		break;
+	case INTERRUPT_VC_I2SPCM:
+		*out_hwirq = INTERRUPT_I2SPCM;
+		break;
+	case INTERRUPT_VC_SDIO:
+		*out_hwirq = INTERRUPT_SDIO;
+		break;
+	case INTERRUPT_VC_UART:
+		*out_hwirq = INTERRUPT_UART;
+		break;
+	case INTERRUPT_VC_ARASANSDIO:
+		*out_hwirq = INTERRUPT_ARASANSDIO;
+		break;
+	}
+
+        *out_type = IRQ_TYPE_NONE;
+        return 0;
+}
+
+static struct irq_domain_ops armctrl_ops = {
+        .xlate = armctrl_xlate
+};
+
+void __init armctrl_dt_init(void)
+{
+	struct device_node *np;
+	struct irq_domain *domain;
+
+	np = of_find_compatible_node(NULL, NULL, "brcm,bcm2708-armctrl-ic");
+	if (!np)
+		return;
+
+        domain = irq_domain_add_legacy(np, NR_IRQS, IRQ_ARMCTRL_START, 0,
+					&armctrl_ops, NULL);
+        WARN_ON(!domain);
+}
+#else
+void __init armctrl_dt_init(void) { }
+#endif /* CONFIG_OF */
+
+#if defined(CONFIG_PM)
+
+/* for kernels 3.xx use the new syscore_ops apis but for older kernels use the sys dev class */
+
+/* Static defines
+ * struct armctrl_device - VIC PM device (< 3.xx)
+ * @sysdev: The system device which is registered. (< 3.xx)
+ * @irq: The IRQ number for the base of the VIC.
+ * @base: The register base for the VIC.
+ * @resume_sources: A bitmask of interrupts for resume.
+ * @resume_irqs: The IRQs enabled for resume.
+ * @int_select: Save for VIC_INT_SELECT.
+ * @int_enable: Save for VIC_INT_ENABLE.
+ * @soft_int: Save for VIC_INT_SOFT.
+ * @protect: Save for VIC_PROTECT.
+ */
+struct armctrl_info {
+	void __iomem *base;
+	int irq;
+	u32 resume_sources;
+	u32 resume_irqs;
+	u32 int_select;
+	u32 int_enable;
+	u32 soft_int;
+	u32 protect;
+} armctrl;
+
+static int armctrl_suspend(void)
+{
+	return 0;
+}
+
+static void armctrl_resume(void)
+{
+	return;
+}
+
+/**
+ * armctrl_pm_register - Register a VIC for later power management control
+ * @base: The base address of the VIC.
+ * @irq: The base IRQ for the VIC.
+ * @resume_sources: bitmask of interrupts allowed for resume sources.
+ *
+ * For older kernels (< 3.xx) do -
+ * Register the VIC with the system device tree so that it can be notified
+ * of suspend and resume requests and ensure that the correct actions are
+ * taken to re-instate the settings on resume.
+ */
+static void __init armctrl_pm_register(void __iomem * base, unsigned int irq,
+				       u32 resume_sources)
+{
+	armctrl.base = base;
+	armctrl.resume_sources = resume_sources;
+	armctrl.irq = irq;
+}
+
+static int armctrl_set_wake(struct irq_data *d, unsigned int on)
+{
+	unsigned int off = d->irq & 31;
+	u32 bit = 1 << off;
+
+	if (!(bit & armctrl.resume_sources))
+		return -EINVAL;
+
+	if (on)
+		armctrl.resume_irqs |= bit;
+	else
+		armctrl.resume_irqs &= ~bit;
+
+	return 0;
+}
+
+#else
+static inline void armctrl_pm_register(void __iomem * base, unsigned int irq,
+				       u32 arg1)
+{
+}
+
+#define armctrl_suspend NULL
+#define armctrl_resume NULL
+#define armctrl_set_wake NULL
+#endif /* CONFIG_PM */
+
+static struct syscore_ops armctrl_syscore_ops = {
+	.suspend = armctrl_suspend,
+	.resume = armctrl_resume,
+};
+
+/**
+ * armctrl_syscore_init - initicall to register VIC pm functions
+ *
+ * This is called via late_initcall() to register
+ * the resources for the VICs due to the early
+ * nature of the VIC's registration.
+*/
+static int __init armctrl_syscore_init(void)
+{
+	register_syscore_ops(&armctrl_syscore_ops);
+	return 0;
+}
+
+late_initcall(armctrl_syscore_init);
+
+static struct irq_chip armctrl_chip = {
+	.name = "ARMCTRL",
+	.irq_ack = NULL,
+	.irq_mask = armctrl_mask_irq,
+	.irq_unmask = armctrl_unmask_irq,
+	.irq_set_wake = armctrl_set_wake,
+};
+
+/**
+ * armctrl_init - initialise a vectored interrupt controller
+ * @base: iomem base address
+ * @irq_start: starting interrupt number, must be muliple of 32
+ * @armctrl_sources: bitmask of interrupt sources to allow
+ * @resume_sources: bitmask of interrupt sources to allow for resume
+ */
+int __init armctrl_init(void __iomem * base, unsigned int irq_start,
+			u32 armctrl_sources, u32 resume_sources)
+{
+	unsigned int irq;
+
+	for (irq = 0; irq < NR_IRQS; irq++) {
+		unsigned int data = irq;
+		if (irq >= INTERRUPT_JPEG && irq <= INTERRUPT_ARASANSDIO)
+			data = remap_irqs[irq - INTERRUPT_JPEG];
+
+		irq_set_chip(irq, &armctrl_chip);
+		irq_set_chip_data(irq, (void *)data);
+		irq_set_handler(irq, handle_level_irq);
+		set_irq_flags(irq, IRQF_VALID | IRQF_PROBE | IRQF_DISABLED);
+	}
+
+	armctrl_pm_register(base, irq_start, resume_sources);
+	init_FIQ(FIQ_START);
+	armctrl_dt_init();
+	return 0;
+}

arch/arm/mach-bcm2708/armctrl.h

@@ -0,0 +1,27 @@
+/*
+ *  linux/arch/arm/mach-bcm2708/armctrl.h
+ *
+ *  Copyright (C) 2010 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#ifndef __BCM2708_ARMCTRL_H
+#define __BCM2708_ARMCTRL_H
+
+extern int __init armctrl_init(void __iomem * base, unsigned int irq_start,
+			       u32 armctrl_sources, u32 resume_sources);
+
+#endif

arch/arm/mach-bcm2708/bcm2708.h

@@ -0,0 +1,49 @@
+/*
+ * linux/arch/arm/mach-bcm2708/bcm2708.h
+ *
+ * BCM2708 machine support header
+ *
+ *  Copyright (C) 2010 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#ifndef __BCM2708_BCM2708_H
+#define __BCM2708_BCM2708_H
+
+#include <linux/amba/bus.h>
+
+extern void __init bcm2708_init(void);
+extern void __init bcm2708_init_irq(void);
+extern void __init bcm2708_map_io(void);
+extern struct sys_timer bcm2708_timer;
+extern unsigned int mmc_status(struct device *dev);
+
+#define AMBA_DEVICE(name, busid, base, plat)			\
+static struct amba_device name##_device = {			\
+	.dev		= {					\
+		.coherent_dma_mask = ~0,			\
+		.init_name = busid,				\
+		.platform_data = plat,				\
+	},							\
+	.res		= {					\
+		.start	= base##_BASE,		\
+		.end	= (base##_BASE) + SZ_4K - 1,\
+		.flags	= IORESOURCE_MEM,			\
+	},							\
+	.irq		= base##_IRQ,				\
+}
+
+#endif

arch/arm/mach-bcm2708/bcm2708_gpio.c

@@ -0,0 +1,401 @@
+/*
+ *  linux/arch/arm/mach-bcm2708/bcm2708_gpio.c
+ *
+ *  Copyright (C) 2010 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/spinlock.h>
+#include <linux/module.h>
+#include <linux/delay.h>
+#include <linux/list.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/interrupt.h>
+#include <linux/slab.h>
+#include <mach/gpio.h>
+#include <linux/gpio.h>
+#include <linux/platform_device.h>
+#include <mach/platform.h>
+
+#include <linux/platform_data/bcm2708.h>
+
+#define BCM_GPIO_DRIVER_NAME "bcm2708_gpio"
+#define DRIVER_NAME BCM_GPIO_DRIVER_NAME
+#define BCM_GPIO_USE_IRQ 1
+
+#define GPIOFSEL(x)  (0x00+(x)*4)
+#define GPIOSET(x)   (0x1c+(x)*4)
+#define GPIOCLR(x)   (0x28+(x)*4)
+#define GPIOLEV(x)   (0x34+(x)*4)
+#define GPIOEDS(x)   (0x40+(x)*4)
+#define GPIOREN(x)   (0x4c+(x)*4)
+#define GPIOFEN(x)   (0x58+(x)*4)
+#define GPIOHEN(x)   (0x64+(x)*4)
+#define GPIOLEN(x)   (0x70+(x)*4)
+#define GPIOAREN(x)  (0x7c+(x)*4)
+#define GPIOAFEN(x)  (0x88+(x)*4)
+#define GPIOUD(x)    (0x94+(x)*4)
+#define GPIOUDCLK(x) (0x98+(x)*4)
+
+enum { GPIO_FSEL_INPUT, GPIO_FSEL_OUTPUT,
+	GPIO_FSEL_ALT5, GPIO_FSEL_ALT_4,
+	GPIO_FSEL_ALT0, GPIO_FSEL_ALT1,
+	GPIO_FSEL_ALT2, GPIO_FSEL_ALT3,
+};
+
+	/* Each of the two spinlocks protects a different set of hardware
+	 * regiters and data structurs. This decouples the code of the IRQ from
+	 * the GPIO code. This also makes the case of a GPIO routine call from
+	 * the IRQ code simpler.
+	 */
+static DEFINE_SPINLOCK(lock);	/* GPIO registers */
+
+struct bcm2708_gpio {
+	struct list_head list;
+	void __iomem *base;
+	struct gpio_chip gc;
+	unsigned long rising[(BCM2708_NR_GPIOS + 31) / 32];
+	unsigned long falling[(BCM2708_NR_GPIOS + 31) / 32];
+	unsigned long high[(BCM2708_NR_GPIOS + 31) / 32];
+	unsigned long low[(BCM2708_NR_GPIOS + 31) / 32];
+};
+
+static int bcm2708_set_function(struct gpio_chip *gc, unsigned offset,
+				int function)
+{
+	struct bcm2708_gpio *gpio = container_of(gc, struct bcm2708_gpio, gc);
+	unsigned long flags;
+	unsigned gpiodir;
+	unsigned gpio_bank = offset / 10;
+	unsigned gpio_field_offset = (offset - 10 * gpio_bank) * 3;
+
+//printk(KERN_ERR DRIVER_NAME ": bcm2708_gpio_set_function %p (%d,%d)\n", gc, offset, function);
+	if (offset >= BCM2708_NR_GPIOS)
+		return -EINVAL;
+
+	spin_lock_irqsave(&lock, flags);
+
+	gpiodir = readl(gpio->base + GPIOFSEL(gpio_bank));
+	gpiodir &= ~(7 << gpio_field_offset);
+	gpiodir |= function << gpio_field_offset;
+	writel(gpiodir, gpio->base + GPIOFSEL(gpio_bank));
+	spin_unlock_irqrestore(&lock, flags);
+	gpiodir = readl(gpio->base + GPIOFSEL(gpio_bank));
+
+	return 0;
+}
+
+static int bcm2708_gpio_dir_in(struct gpio_chip *gc, unsigned offset)
+{
+	return bcm2708_set_function(gc, offset, GPIO_FSEL_INPUT);
+}
+
+static void bcm2708_gpio_set(struct gpio_chip *gc, unsigned offset, int value);
+static int bcm2708_gpio_dir_out(struct gpio_chip *gc, unsigned offset,
+				int value)
+{
+	int ret;
+	ret = bcm2708_set_function(gc, offset, GPIO_FSEL_OUTPUT);
+	if (ret >= 0)
+		bcm2708_gpio_set(gc, offset, value);
+	return ret;
+}
+
+static int bcm2708_gpio_get(struct gpio_chip *gc, unsigned offset)
+{
+	struct bcm2708_gpio *gpio = container_of(gc, struct bcm2708_gpio, gc);
+	unsigned gpio_bank = offset / 32;
+	unsigned gpio_field_offset = (offset - 32 * gpio_bank);
+	unsigned lev;
+
+	if (offset >= BCM2708_NR_GPIOS)
+		return 0;
+	lev = readl(gpio->base + GPIOLEV(gpio_bank));
+//printk(KERN_ERR DRIVER_NAME ": bcm2708_gpio_get %p (%d)=%d\n", gc, offset, 0x1 & (lev>>gpio_field_offset));
+	return 0x1 & (lev >> gpio_field_offset);
+}
+
+static void bcm2708_gpio_set(struct gpio_chip *gc, unsigned offset, int value)
+{
+	struct bcm2708_gpio *gpio = container_of(gc, struct bcm2708_gpio, gc);
+	unsigned gpio_bank = offset / 32;
+	unsigned gpio_field_offset = (offset - 32 * gpio_bank);
+//printk(KERN_ERR DRIVER_NAME ": bcm2708_gpio_set %p (%d=%d)\n", gc, offset, value);
+	if (offset >= BCM2708_NR_GPIOS)
+		return;
+	if (value)
+		writel(1 << gpio_field_offset, gpio->base + GPIOSET(gpio_bank));
+	else
+		writel(1 << gpio_field_offset, gpio->base + GPIOCLR(gpio_bank));
+}
+
+/**********************
+ * extension to configure pullups
+ */
+int bcm2708_gpio_setpull(struct gpio_chip *gc, unsigned offset,
+		bcm2708_gpio_pull_t value)
+{
+	struct bcm2708_gpio *gpio = container_of(gc, struct bcm2708_gpio, gc);
+	unsigned gpio_bank = offset / 32;
+	unsigned gpio_field_offset = (offset - 32 * gpio_bank);
+
+	if (offset >= BCM2708_NR_GPIOS)
+		return -EINVAL;
+
+	switch (value) {
+	case BCM2708_PULL_UP:
+		writel(2, gpio->base + GPIOUD(0));
+		break;
+	case BCM2708_PULL_DOWN:
+		writel(1, gpio->base + GPIOUD(0));
+		break;
+	case BCM2708_PULL_OFF:
+		writel(0, gpio->base + GPIOUD(0));
+		break;
+	}
+
+	udelay(5);
+	writel(1 << gpio_field_offset, gpio->base + GPIOUDCLK(gpio_bank));
+	udelay(5);
+	writel(0, gpio->base + GPIOUD(0));
+	writel(0 << gpio_field_offset, gpio->base + GPIOUDCLK(gpio_bank));
+
+	return 0;
+}
+EXPORT_SYMBOL(bcm2708_gpio_setpull);
+
+/*************************************************************************************************************************
+ * bcm2708 GPIO IRQ
+ */
+
+#if BCM_GPIO_USE_IRQ
+
+static int bcm2708_gpio_to_irq(struct gpio_chip *chip, unsigned gpio)
+{
+	return gpio_to_irq(gpio);
+}
+
+static int bcm2708_gpio_irq_set_type(struct irq_data *d, unsigned type)
+{
+	unsigned irq = d->irq;
+	struct bcm2708_gpio *gpio = irq_get_chip_data(irq);
+	unsigned gn = irq_to_gpio(irq);
+	unsigned gb = gn / 32;
+	unsigned go = gn % 32;
+
+	gpio->rising[gb]  &= ~(1 << go);
+	gpio->falling[gb] &= ~(1 << go);
+	gpio->high[gb]    &= ~(1 << go);
+	gpio->low[gb]     &= ~(1 << go);
+
+	if (type & ~(IRQ_TYPE_EDGE_FALLING | IRQ_TYPE_EDGE_RISING | IRQ_TYPE_LEVEL_LOW | IRQ_TYPE_LEVEL_HIGH))
+		return -EINVAL;
+
+	if (type & IRQ_TYPE_EDGE_RISING)
+		gpio->rising[gb] |= (1 << go);
+	if (type & IRQ_TYPE_EDGE_FALLING)
+		gpio->falling[gb] |= (1 << go);
+	if (type & IRQ_TYPE_LEVEL_HIGH)
+		gpio->high[gb] |= (1 << go);
+	if (type & IRQ_TYPE_LEVEL_LOW)
+		gpio->low[gb] |= (1 << go);
+	return 0;
+}
+
+static void bcm2708_gpio_irq_mask(struct irq_data *d)
+{
+	unsigned irq = d->irq;
+	struct bcm2708_gpio *gpio = irq_get_chip_data(irq);
+	unsigned gn = irq_to_gpio(irq);
+	unsigned gb = gn / 32;
+	unsigned long rising  = readl(gpio->base + GPIOREN(gb));
+	unsigned long falling = readl(gpio->base + GPIOFEN(gb));
+	unsigned long high    = readl(gpio->base + GPIOHEN(gb));
+	unsigned long low     = readl(gpio->base + GPIOLEN(gb));
+
+	gn = gn % 32;
+
+	writel(rising  & ~(1 << gn), gpio->base + GPIOREN(gb));
+	writel(falling & ~(1 << gn), gpio->base + GPIOFEN(gb));
+	writel(high    & ~(1 << gn), gpio->base + GPIOHEN(gb));
+	writel(low     & ~(1 << gn), gpio->base + GPIOLEN(gb));
+}
+
+static void bcm2708_gpio_irq_unmask(struct irq_data *d)
+{
+	unsigned irq = d->irq;
+	struct bcm2708_gpio *gpio = irq_get_chip_data(irq);
+	unsigned gn = irq_to_gpio(irq);
+	unsigned gb = gn / 32;
+	unsigned go = gn % 32;
+	unsigned long rising  = readl(gpio->base + GPIOREN(gb));
+	unsigned long falling = readl(gpio->base + GPIOFEN(gb));
+	unsigned long high    = readl(gpio->base + GPIOHEN(gb));
+	unsigned long low     = readl(gpio->base + GPIOLEN(gb));
+
+	writel(1 << go, gpio->base + GPIOEDS(gb));
+
+	if (gpio->rising[gb] & (1 << go)) {
+		writel(rising |  (1 << go), gpio->base + GPIOREN(gb));
+	} else {
+		writel(rising & ~(1 << go), gpio->base + GPIOREN(gb));
+	}
+
+	if (gpio->falling[gb] & (1 << go)) {
+		writel(falling |  (1 << go), gpio->base + GPIOFEN(gb));
+	} else {
+		writel(falling & ~(1 << go), gpio->base + GPIOFEN(gb));
+	}
+
+	if (gpio->high[gb] & (1 << go)) {
+		writel(high |  (1 << go), gpio->base + GPIOHEN(gb));
+	} else {
+		writel(high & ~(1 << go), gpio->base + GPIOHEN(gb));
+	}
+
+	if (gpio->low[gb] & (1 << go)) {
+		writel(low |  (1 << go), gpio->base + GPIOLEN(gb));
+	} else {
+		writel(low & ~(1 << go), gpio->base + GPIOLEN(gb));
+	}
+}
+
+static struct irq_chip bcm2708_irqchip = {
+	.name = "GPIO",
+	.irq_enable = bcm2708_gpio_irq_unmask,
+	.irq_disable = bcm2708_gpio_irq_mask,
+	.irq_unmask = bcm2708_gpio_irq_unmask,
+	.irq_mask = bcm2708_gpio_irq_mask,
+	.irq_set_type = bcm2708_gpio_irq_set_type,
+};
+
+static irqreturn_t bcm2708_gpio_interrupt(int irq, void *dev_id)
+{
+	unsigned long edsr;
+	unsigned bank;
+	int i;
+	unsigned gpio;
+	for (bank = 0; bank <= 1; bank++) {
+		edsr = readl(__io_address(GPIO_BASE) + GPIOEDS(bank));
+		for_each_set_bit(i, &edsr, 32) {
+			gpio = i + bank * 32;
+			generic_handle_irq(gpio_to_irq(gpio));
+		}
+		writel(0xffffffff, __io_address(GPIO_BASE) + GPIOEDS(bank));
+	}
+	return IRQ_HANDLED;
+}
+
+static struct irqaction bcm2708_gpio_irq = {
+	.name = "BCM2708 GPIO catchall handler",
+	.flags = IRQF_DISABLED | IRQF_TIMER | IRQF_IRQPOLL,
+	.handler = bcm2708_gpio_interrupt,
+};
+
+static void bcm2708_gpio_irq_init(struct bcm2708_gpio *ucb)
+{
+	unsigned irq;
+
+	ucb->gc.to_irq = bcm2708_gpio_to_irq;
+
+	for (irq = GPIO_IRQ_START; irq < (GPIO_IRQ_START + GPIO_IRQS); irq++) {
+		irq_set_chip_data(irq, ucb);
+		irq_set_chip(irq, &bcm2708_irqchip);
+		set_irq_flags(irq, IRQF_VALID);
+	}
+	setup_irq(IRQ_GPIO3, &bcm2708_gpio_irq);
+}
+
+#else
+
+static void bcm2708_gpio_irq_init(struct bcm2708_gpio *ucb)
+{
+}
+
+#endif /* #if BCM_GPIO_USE_IRQ ***************************************************************************************************************** */
+
+static int bcm2708_gpio_probe(struct platform_device *dev)
+{
+	struct bcm2708_gpio *ucb;
+	struct resource *res;
+	int err = 0;
+
+	printk(KERN_INFO DRIVER_NAME ": bcm2708_gpio_probe %p\n", dev);
+
+	ucb = kzalloc(sizeof(*ucb), GFP_KERNEL);
+	if (NULL == ucb) {
+		printk(KERN_ERR DRIVER_NAME ": failed to allocate "
+		       "mailbox memory\n");
+		err = -ENOMEM;
+		goto err;
+	}
+
+	res = platform_get_resource(dev, IORESOURCE_MEM, 0);
+
+	platform_set_drvdata(dev, ucb);
+	ucb->base = __io_address(GPIO_BASE);
+
+	ucb->gc.label = "bcm2708_gpio";
+	ucb->gc.base = 0;
+	ucb->gc.ngpio = BCM2708_NR_GPIOS;
+	ucb->gc.owner = THIS_MODULE;
+
+	ucb->gc.direction_input = bcm2708_gpio_dir_in;
+	ucb->gc.direction_output = bcm2708_gpio_dir_out;
+	ucb->gc.get = bcm2708_gpio_get;
+	ucb->gc.set = bcm2708_gpio_set;
+	ucb->gc.can_sleep = 0;
+
+	bcm2708_gpio_irq_init(ucb);
+
+	err = gpiochip_add(&ucb->gc);
+	if (err)
+		goto err;
+
+err:
+	return err;
+
+}
+
+static int bcm2708_gpio_remove(struct platform_device *dev)
+{
+	int err = 0;
+	struct bcm2708_gpio *ucb = platform_get_drvdata(dev);
+
+	printk(KERN_ERR DRIVER_NAME ": bcm2708_gpio_remove %p\n", dev);
+
+	err = gpiochip_remove(&ucb->gc);
+
+	platform_set_drvdata(dev, NULL);
+	kfree(ucb);
+
+	return err;
+}
+
+static struct platform_driver bcm2708_gpio_driver = {
+	.probe = bcm2708_gpio_probe,
+	.remove = bcm2708_gpio_remove,
+	.driver = {
+		   .name = "bcm2708_gpio"},
+};
+
+static int __init bcm2708_gpio_init(void)
+{
+	return platform_driver_register(&bcm2708_gpio_driver);
+}
+
+static void __exit bcm2708_gpio_exit(void)
+{
+	platform_driver_unregister(&bcm2708_gpio_driver);
+}
+
+module_init(bcm2708_gpio_init);
+module_exit(bcm2708_gpio_exit);
+
+MODULE_DESCRIPTION("Broadcom BCM2708 GPIO driver");
+MODULE_LICENSE("GPL");

arch/arm/mach-bcm2708/dma.c

@@ -0,0 +1,409 @@
+/*
+ *  linux/arch/arm/mach-bcm2708/dma.c
+ *
+ *  Copyright (C) 2010 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/slab.h>
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <linux/module.h>
+#include <linux/scatterlist.h>
+
+#include <mach/dma.h>
+#include <mach/irqs.h>
+
+/*****************************************************************************\
+ *									     *
+ * Configuration							     *
+ *									     *
+\*****************************************************************************/
+
+#define CACHE_LINE_MASK 31
+#define DRIVER_NAME BCM_DMAMAN_DRIVER_NAME
+#define DEFAULT_DMACHAN_BITMAP 0x10  /* channel 4 only */
+
+/* valid only for channels 0 - 14, 15 has its own base address */
+#define BCM2708_DMA_CHAN(n)	((n)<<8) /* base address */
+#define BCM2708_DMA_CHANIO(dma_base, n) \
+   ((void __iomem *)((char *)(dma_base)+BCM2708_DMA_CHAN(n)))
+
+
+/*****************************************************************************\
+ *									     *
+ * DMA Auxilliary Functions						     *
+ *									     *
+\*****************************************************************************/
+
+/* A DMA buffer on an arbitrary boundary may separate a cache line into a
+   section inside the DMA buffer and another section outside it.
+   Even if we flush DMA buffers from the cache there is always the chance that
+   during a DMA someone will access the part of a cache line that is outside
+   the DMA buffer - which will then bring in unwelcome data.
+   Without being able to dictate our own buffer pools we must insist that
+   DMA buffers consist of a whole number of cache lines.
+*/
+
+extern int
+bcm_sg_suitable_for_dma(struct scatterlist *sg_ptr, int sg_len)
+{
+	int i;
+
+	for (i = 0; i < sg_len; i++) {
+		if (sg_ptr[i].offset & CACHE_LINE_MASK ||
+		    sg_ptr[i].length & CACHE_LINE_MASK)
+			return 0;
+	}
+
+	return 1;
+}
+EXPORT_SYMBOL_GPL(bcm_sg_suitable_for_dma);
+
+extern void
+bcm_dma_start(void __iomem *dma_chan_base, dma_addr_t control_block)
+{
+	dsb();	/* ARM data synchronization (push) operation */
+
+	writel(control_block,	     dma_chan_base + BCM2708_DMA_ADDR);
+	writel(BCM2708_DMA_ACTIVE,   dma_chan_base + BCM2708_DMA_CS);
+}
+
+extern void bcm_dma_wait_idle(void __iomem *dma_chan_base)
+{
+  dsb();
+
+  /* ugly busy wait only option for now */
+  while (readl(dma_chan_base + BCM2708_DMA_CS) & BCM2708_DMA_ACTIVE)
+    cpu_relax();
+}
+
+EXPORT_SYMBOL_GPL(bcm_dma_start);
+
+extern bool bcm_dma_is_busy(void __iomem *dma_chan_base)
+{
+	dsb();
+
+	return readl(dma_chan_base + BCM2708_DMA_CS) & BCM2708_DMA_ACTIVE;
+}
+EXPORT_SYMBOL_GPL(bcm_dma_is_busy);
+
+/* Complete an ongoing DMA (assuming its results are to be ignored)
+   Does nothing if there is no DMA in progress.
+   This routine waits for the current AXI transfer to complete before
+   terminating the current DMA.	 If the current transfer is hung on a DREQ used
+   by an uncooperative peripheral the AXI transfer may never complete.	In this
+   case the routine times out and return a non-zero error code.
+   Use of this routine doesn't guarantee that the ongoing or aborted DMA
+   does not produce an interrupt.
+*/
+extern int
+bcm_dma_abort(void __iomem *dma_chan_base)
+{
+	unsigned long int cs;
+	int rc = 0;
+
+	cs = readl(dma_chan_base + BCM2708_DMA_CS);
+
+	if (BCM2708_DMA_ACTIVE & cs) {
+		long int timeout = 10000;
+
+		/* write 0 to the active bit - pause the DMA */
+		writel(0, dma_chan_base + BCM2708_DMA_CS);
+
+		/* wait for any current AXI transfer to complete */
+		while (0 != (cs & BCM2708_DMA_ISPAUSED) && --timeout >= 0)
+			cs = readl(dma_chan_base + BCM2708_DMA_CS);
+
+		if (0 != (cs & BCM2708_DMA_ISPAUSED)) {
+			/* we'll un-pause when we set of our next DMA */
+			rc = -ETIMEDOUT;
+
+		} else if (BCM2708_DMA_ACTIVE & cs) {
+			/* terminate the control block chain */
+			writel(0, dma_chan_base + BCM2708_DMA_NEXTCB);
+
+			/* abort the whole DMA */
+			writel(BCM2708_DMA_ABORT | BCM2708_DMA_ACTIVE,
+			       dma_chan_base + BCM2708_DMA_CS);
+		}
+	}
+
+	return rc;
+}
+EXPORT_SYMBOL_GPL(bcm_dma_abort);
+
+
+/***************************************************************************** \
+ *									     *
+ * DMA Manager Device Methods						     *
+ *									     *
+\*****************************************************************************/
+
+struct vc_dmaman {
+	void __iomem *dma_base;
+	u32 chan_available; /* bitmap of available channels */
+	u32 has_feature[BCM_DMA_FEATURE_COUNT]; /* bitmap of feature presence */
+};
+
+static void vc_dmaman_init(struct vc_dmaman *dmaman, void __iomem *dma_base,
+			   u32 chans_available)
+{
+	dmaman->dma_base = dma_base;
+	dmaman->chan_available = chans_available;
+	dmaman->has_feature[BCM_DMA_FEATURE_FAST_ORD] = 0x0c;  /* chans 2 & 3 */
+	dmaman->has_feature[BCM_DMA_FEATURE_BULK_ORD] = 0x01;  /* chan 0 */
+	dmaman->has_feature[BCM_DMA_FEATURE_NORMAL_ORD] = 0xfe;  /* chans 1 to 7 */
+	dmaman->has_feature[BCM_DMA_FEATURE_LITE_ORD] = 0x7f00;  /* chans 8 to 14 */
+}
+
+static int vc_dmaman_chan_alloc(struct vc_dmaman *dmaman,
+				unsigned preferred_feature_set)
+{
+	u32 chans;
+	int feature;
+
+	chans = dmaman->chan_available;
+	for (feature = 0; feature < BCM_DMA_FEATURE_COUNT; feature++)
+		/* select the subset of available channels with the desired
+		   feature so long as some of the candidate channels have that
+		   feature */
+		if ((preferred_feature_set & (1 << feature)) &&
+		    (chans & dmaman->has_feature[feature]))
+			chans &= dmaman->has_feature[feature];
+
+	if (chans) {
+		int chan = 0;
+		/* return the ordinal of the first channel in the bitmap */
+		while (chans != 0 && (chans & 1) == 0) {
+			chans >>= 1;
+			chan++;
+		}
+		/* claim the channel */
+		dmaman->chan_available &= ~(1 << chan);
+		return chan;
+	} else
+		return -ENOMEM;
+}
+
+static int vc_dmaman_chan_free(struct vc_dmaman *dmaman, int chan)
+{
+	if (chan < 0)
+		return -EINVAL;
+	else if ((1 << chan) & dmaman->chan_available)
+		return -EIDRM;
+	else {
+		dmaman->chan_available |= (1 << chan);
+		return 0;
+	}
+}
+
+/*****************************************************************************\
+ *									     *
+ * DMA IRQs								     *
+ *									     *
+\*****************************************************************************/
+
+static unsigned char bcm_dma_irqs[] = {
+	IRQ_DMA0,
+	IRQ_DMA1,
+	IRQ_DMA2,
+	IRQ_DMA3,
+	IRQ_DMA4,
+	IRQ_DMA5,
+	IRQ_DMA6,
+	IRQ_DMA7,
+	IRQ_DMA8,
+	IRQ_DMA9,
+	IRQ_DMA10,
+	IRQ_DMA11,
+	IRQ_DMA12
+};
+
+
+/***************************************************************************** \
+ *									     *
+ * DMA Manager Monitor							     *
+ *									     *
+\*****************************************************************************/
+
+static struct device *dmaman_dev;	/* we assume there's only one! */
+
+extern int bcm_dma_chan_alloc(unsigned preferred_feature_set,
+			      void __iomem **out_dma_base, int *out_dma_irq)
+{
+	if (!dmaman_dev)
+		return -ENODEV;
+	else {
+		struct vc_dmaman *dmaman  = dev_get_drvdata(dmaman_dev);
+		int rc;
+
+		device_lock(dmaman_dev);
+		rc = vc_dmaman_chan_alloc(dmaman, preferred_feature_set);
+		if (rc >= 0) {
+			*out_dma_base = BCM2708_DMA_CHANIO(dmaman->dma_base,
+							   rc);
+			*out_dma_irq = bcm_dma_irqs[rc];
+		}
+		device_unlock(dmaman_dev);
+
+		return rc;
+	}
+}
+EXPORT_SYMBOL_GPL(bcm_dma_chan_alloc);
+
+extern int bcm_dma_chan_free(int channel)
+{
+	if (dmaman_dev) {
+		struct vc_dmaman *dmaman = dev_get_drvdata(dmaman_dev);
+		int rc;
+
+		device_lock(dmaman_dev);
+		rc = vc_dmaman_chan_free(dmaman, channel);
+		device_unlock(dmaman_dev);
+
+		return rc;
+	} else
+		return -ENODEV;
+}
+EXPORT_SYMBOL_GPL(bcm_dma_chan_free);
+
+static int dev_dmaman_register(const char *dev_name, struct device *dev)
+{
+	int rc = dmaman_dev ? -EINVAL : 0;
+	dmaman_dev = dev;
+	return rc;
+}
+
+static void dev_dmaman_deregister(const char *dev_name, struct device *dev)
+{
+	dmaman_dev = NULL;
+}
+
+/*****************************************************************************\
+ *									     *
+ * DMA Device								     *
+ *									     *
+\*****************************************************************************/
+
+static int dmachans = -1; /* module parameter */
+
+static int bcm_dmaman_probe(struct platform_device *pdev)
+{
+	int ret = 0;
+	struct vc_dmaman *dmaman;
+	struct resource *dma_res = NULL;
+	void __iomem *dma_base = NULL;
+	int have_dma_region = 0;
+
+	dmaman = kzalloc(sizeof(*dmaman), GFP_KERNEL);
+	if (NULL == dmaman) {
+		printk(KERN_ERR DRIVER_NAME ": failed to allocate "
+		       "DMA management memory\n");
+		ret = -ENOMEM;
+	} else {
+
+		dma_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+		if (dma_res == NULL) {
+			printk(KERN_ERR DRIVER_NAME ": failed to obtain memory "
+			       "resource\n");
+			ret = -ENODEV;
+		} else if (!request_mem_region(dma_res->start,
+					       resource_size(dma_res),
+					       DRIVER_NAME)) {
+			dev_err(&pdev->dev, "cannot obtain DMA region\n");
+			ret = -EBUSY;
+		} else {
+			have_dma_region = 1;
+			dma_base = ioremap(dma_res->start,
+					   resource_size(dma_res));
+			if (!dma_base) {
+				dev_err(&pdev->dev, "cannot map DMA region\n");
+				ret = -ENOMEM;
+			} else {
+				/* use module parameter if one was provided */
+				if (dmachans > 0)
+					vc_dmaman_init(dmaman, dma_base,
+						       dmachans);
+				else
+					vc_dmaman_init(dmaman, dma_base,
+						       DEFAULT_DMACHAN_BITMAP);
+
+				platform_set_drvdata(pdev, dmaman);
+				dev_dmaman_register(DRIVER_NAME, &pdev->dev);
+
+				printk(KERN_INFO DRIVER_NAME ": DMA manager "
+				       "at %p\n", dma_base);
+			}
+		}
+	}
+	if (ret != 0) {
+		if (dma_base)
+			iounmap(dma_base);
+		if (dma_res && have_dma_region)
+			release_mem_region(dma_res->start,
+					   resource_size(dma_res));
+		if (dmaman)
+			kfree(dmaman);
+	}
+	return ret;
+}
+
+static int bcm_dmaman_remove(struct platform_device *pdev)
+{
+	struct vc_dmaman *dmaman = platform_get_drvdata(pdev);
+
+	platform_set_drvdata(pdev, NULL);
+	dev_dmaman_deregister(DRIVER_NAME, &pdev->dev);
+	kfree(dmaman);
+
+	return 0;
+}
+
+static struct platform_driver bcm_dmaman_driver = {
+	.probe = bcm_dmaman_probe,
+	.remove = bcm_dmaman_remove,
+
+	.driver = {
+		   .name = DRIVER_NAME,
+		   .owner = THIS_MODULE,
+		   },
+};
+
+/*****************************************************************************\
+ *									     *
+ * Driver init/exit							     *
+ *									     *
+\*****************************************************************************/
+
+static int __init bcm_dmaman_drv_init(void)
+{
+	int ret;
+
+	ret = platform_driver_register(&bcm_dmaman_driver);
+	if (ret != 0) {
+		printk(KERN_ERR DRIVER_NAME ": failed to register "
+		       "on platform\n");
+	}
+
+	return ret;
+}
+
+static void __exit bcm_dmaman_drv_exit(void)
+{
+	platform_driver_unregister(&bcm_dmaman_driver);
+}
+
+module_init(bcm_dmaman_drv_init);
+module_exit(bcm_dmaman_drv_exit);
+
+module_param(dmachans, int, 0644);
+
+MODULE_AUTHOR("Gray Girling <grayg@broadcom.com>");
+MODULE_DESCRIPTION("DMA channel manager driver");
+MODULE_LICENSE("GPL");
+
+MODULE_PARM_DESC(dmachans, "Bitmap of DMA channels available to the ARM");

arch/arm/mach-bcm2708/include/mach/arm_control.h

@@ -0,0 +1,419 @@
+/*
+ *  linux/arch/arm/mach-bcm2708/arm_control.h
+ *
+ *  Copyright (C) 2010 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#ifndef __BCM2708_ARM_CONTROL_H
+#define __BCM2708_ARM_CONTROL_H
+
+/*
+ * Definitions and addresses for the ARM CONTROL logic
+ * This file is manually generated.
+ */
+
+#define ARM_BASE  0x7E00B000
+
+/* Basic configuration */
+#define ARM_CONTROL0  HW_REGISTER_RW(ARM_BASE+0x000)
+#define ARM_C0_SIZ128M   0x00000000
+#define ARM_C0_SIZ256M   0x00000001
+#define ARM_C0_SIZ512M   0x00000002
+#define ARM_C0_SIZ1G     0x00000003
+#define ARM_C0_BRESP0    0x00000000
+#define ARM_C0_BRESP1    0x00000004
+#define ARM_C0_BRESP2    0x00000008
+#define ARM_C0_BOOTHI    0x00000010
+#define ARM_C0_UNUSED05  0x00000020 /* free */
+#define ARM_C0_FULLPERI  0x00000040
+#define ARM_C0_UNUSED78  0x00000180 /* free */
+#define ARM_C0_JTAGMASK  0x00000E00
+#define ARM_C0_JTAGOFF   0x00000000
+#define ARM_C0_JTAGBASH  0x00000800 /* Debug on GPIO off */
+#define ARM_C0_JTAGGPIO  0x00000C00 /* Debug on GPIO on */
+#define ARM_C0_APROTMSK  0x0000F000
+#define ARM_C0_DBG0SYNC  0x00010000 /* VPU0 halt sync */
+#define ARM_C0_DBG1SYNC  0x00020000 /* VPU1 halt sync */
+#define ARM_C0_SWDBGREQ  0x00040000 /* HW debug request */
+#define ARM_C0_PASSHALT  0x00080000 /* ARM halt passed to debugger */
+#define ARM_C0_PRIO_PER  0x00F00000 /* per priority mask */
+#define ARM_C0_PRIO_L2   0x0F000000
+#define ARM_C0_PRIO_UC   0xF0000000
+
+#define ARM_C0_APROTPASS  0x0000A000 /* Translate 1:1 */
+#define ARM_C0_APROTUSER  0x00000000 /* Only user mode */
+#define ARM_C0_APROTSYST  0x0000F000 /* Only system mode */
+
+
+#define ARM_CONTROL1  HW_REGISTER_RW(ARM_BASE+0x440)
+#define ARM_C1_TIMER     0x00000001 /* re-route timer IRQ  to VC */
+#define ARM_C1_MAIL      0x00000002 /* re-route Mail IRQ   to VC */
+#define ARM_C1_BELL0     0x00000004 /* re-route Doorbell 0 to VC */
+#define ARM_C1_BELL1     0x00000008 /* re-route Doorbell 1 to VC */
+#define ARM_C1_PERSON    0x00000100 /* peripherals on */
+#define ARM_C1_REQSTOP   0x00000200 /* ASYNC bridge request stop */
+
+#define ARM_STATUS    HW_REGISTER_RW(ARM_BASE+0x444)
+#define ARM_S_ACKSTOP    0x80000000 /* Bridge stopped */
+#define ARM_S_READPEND   0x000003FF /* pending reads counter */
+#define ARM_S_WRITPEND   0x000FFC00 /* pending writes counter */
+
+#define ARM_ERRHALT   HW_REGISTER_RW(ARM_BASE+0x448)
+#define ARM_EH_PERIBURST  0x00000001 /* Burst write seen on peri bus */
+#define ARM_EH_ILLADDRS1  0x00000002 /* Address bits 25-27 error */
+#define ARM_EH_ILLADDRS2  0x00000004 /* Address bits 31-28 error */
+#define ARM_EH_VPU0HALT   0x00000008 /* VPU0 halted & in debug mode */
+#define ARM_EH_VPU1HALT   0x00000010 /* VPU1 halted & in debug mode */
+#define ARM_EH_ARMHALT    0x00000020 /* ARM in halted debug mode */
+
+#define ARM_ID_SECURE HW_REGISTER_RW(ARM_BASE+0x00C)
+#define ARM_ID        HW_REGISTER_RW(ARM_BASE+0x44C)
+#define ARM_IDVAL        0x364D5241
+
+/* Translation memory */
+#define ARM_TRANSLATE HW_REGISTER_RW(ARM_BASE+0x100)
+/* 32 locations: 0x100.. 0x17F */
+/* 32 spare means we CAN go to 64 pages.... */
+
+
+/* Interrupts */
+#define ARM_IRQ_PEND0 HW_REGISTER_RW(ARM_BASE+0x200)        /* Top IRQ bits */
+#define ARM_I0_TIMER    0x00000001 /* timer IRQ */
+#define ARM_I0_MAIL     0x00000002 /* Mail IRQ */
+#define ARM_I0_BELL0    0x00000004 /* Doorbell 0 */
+#define ARM_I0_BELL1    0x00000008 /* Doorbell 1 */
+#define ARM_I0_BANK1    0x00000100 /* Bank1 IRQ */
+#define ARM_I0_BANK2    0x00000200 /* Bank2 IRQ */
+
+#define ARM_IRQ_PEND1 HW_REGISTER_RW(ARM_BASE+0x204) /* All bank1 IRQ bits */
+/* todo: all I1_interrupt sources */
+#define ARM_IRQ_PEND2 HW_REGISTER_RW(ARM_BASE+0x208) /* All bank2 IRQ bits */
+/* todo: all I2_interrupt sources */
+
+#define ARM_IRQ_FAST  HW_REGISTER_RW(ARM_BASE+0x20C) /* FIQ control */
+#define ARM_IF_INDEX    0x0000007F     /* FIQ select */
+#define ARM_IF_ENABLE   0x00000080     /* FIQ enable */
+#define ARM_IF_VCMASK   0x0000003F     /* FIQ = (index from VC source) */
+#define ARM_IF_TIMER    0x00000040     /* FIQ = ARM timer */
+#define ARM_IF_MAIL     0x00000041     /* FIQ = ARM Mail */
+#define ARM_IF_BELL0    0x00000042     /* FIQ = ARM Doorbell 0 */
+#define ARM_IF_BELL1    0x00000043     /* FIQ = ARM Doorbell 1 */
+#define ARM_IF_VP0HALT  0x00000044     /* FIQ = VPU0 Halt seen */
+#define ARM_IF_VP1HALT  0x00000045     /* FIQ = VPU1 Halt seen */
+#define ARM_IF_ILLEGAL  0x00000046     /* FIQ = Illegal access seen */
+
+#define ARM_IRQ_ENBL1 HW_REGISTER_RW(ARM_BASE+0x210) /* Bank1 enable bits */
+#define ARM_IRQ_ENBL2 HW_REGISTER_RW(ARM_BASE+0x214) /* Bank2 enable bits */
+#define ARM_IRQ_ENBL3 HW_REGISTER_RW(ARM_BASE+0x218) /* ARM irqs enable bits */
+#define ARM_IRQ_DIBL1 HW_REGISTER_RW(ARM_BASE+0x21C) /* Bank1 disable bits */
+#define ARM_IRQ_DIBL2 HW_REGISTER_RW(ARM_BASE+0x220) /* Bank2 disable bits */
+#define ARM_IRQ_DIBL3 HW_REGISTER_RW(ARM_BASE+0x224) /* ARM irqs disable bits */
+#define ARM_IE_TIMER    0x00000001     /* Timer IRQ */
+#define ARM_IE_MAIL     0x00000002     /* Mail IRQ */
+#define ARM_IE_BELL0    0x00000004     /* Doorbell 0 */
+#define ARM_IE_BELL1    0x00000008     /* Doorbell 1 */
+#define ARM_IE_VP0HALT  0x00000010     /* VPU0 Halt */
+#define ARM_IE_VP1HALT  0x00000020     /* VPU1 Halt */
+#define ARM_IE_ILLEGAL  0x00000040     /* Illegal access seen */
+
+/* Timer */
+/* For reg. fields see sp804 spec. */
+#define ARM_T_LOAD    HW_REGISTER_RW(ARM_BASE+0x400)
+#define ARM_T_VALUE   HW_REGISTER_RW(ARM_BASE+0x404)
+#define ARM_T_CONTROL HW_REGISTER_RW(ARM_BASE+0x408)
+#define ARM_T_IRQCNTL HW_REGISTER_RW(ARM_BASE+0x40C)
+#define ARM_T_RAWIRQ  HW_REGISTER_RW(ARM_BASE+0x410)
+#define ARM_T_MSKIRQ  HW_REGISTER_RW(ARM_BASE+0x414)
+#define ARM_T_RELOAD  HW_REGISTER_RW(ARM_BASE+0x418)
+#define ARM_T_PREDIV  HW_REGISTER_RW(ARM_BASE+0x41c)
+#define ARM_T_FREECNT HW_REGISTER_RW(ARM_BASE+0x420)
+
+#define TIMER_CTRL_ONESHOT  (1 << 0)
+#define TIMER_CTRL_32BIT    (1 << 1)
+#define TIMER_CTRL_DIV1     (0 << 2)
+#define TIMER_CTRL_DIV16    (1 << 2)
+#define TIMER_CTRL_DIV256   (2 << 2)
+#define TIMER_CTRL_IE       (1 << 5)
+#define TIMER_CTRL_PERIODIC (1 << 6)
+#define TIMER_CTRL_ENABLE   (1 << 7)
+#define TIMER_CTRL_DBGHALT  (1 << 8)
+#define TIMER_CTRL_ENAFREE  (1 << 9)
+#define TIMER_CTRL_FREEDIV_SHIFT 16)
+#define TIMER_CTRL_FREEDIV_MASK  0xff
+
+/* Semaphores, Doorbells, Mailboxes */
+#define ARM_SBM_OWN0  (ARM_BASE+0x800)
+#define ARM_SBM_OWN1  (ARM_BASE+0x900)
+#define ARM_SBM_OWN2  (ARM_BASE+0xA00)
+#define ARM_SBM_OWN3  (ARM_BASE+0xB00)
+
+/* MAILBOXES
+ * Register flags are common across all
+ * owner registers. See end of this section
+ *
+ * Semaphores, Doorbells, Mailboxes Owner 0
+ *
+ */
+
+#define ARM_0_SEMS       HW_REGISTER_RW(ARM_SBM_OWN0+0x00)
+#define ARM_0_SEM0       HW_REGISTER_RW(ARM_SBM_OWN0+0x00)
+#define ARM_0_SEM1       HW_REGISTER_RW(ARM_SBM_OWN0+0x04)
+#define ARM_0_SEM2       HW_REGISTER_RW(ARM_SBM_OWN0+0x08)
+#define ARM_0_SEM3       HW_REGISTER_RW(ARM_SBM_OWN0+0x0C)
+#define ARM_0_SEM4       HW_REGISTER_RW(ARM_SBM_OWN0+0x10)
+#define ARM_0_SEM5       HW_REGISTER_RW(ARM_SBM_OWN0+0x14)
+#define ARM_0_SEM6       HW_REGISTER_RW(ARM_SBM_OWN0+0x18)
+#define ARM_0_SEM7       HW_REGISTER_RW(ARM_SBM_OWN0+0x1C)
+#define ARM_0_BELL0      HW_REGISTER_RW(ARM_SBM_OWN0+0x40)
+#define ARM_0_BELL1      HW_REGISTER_RW(ARM_SBM_OWN0+0x44)
+#define ARM_0_BELL2      HW_REGISTER_RW(ARM_SBM_OWN0+0x48)
+#define ARM_0_BELL3      HW_REGISTER_RW(ARM_SBM_OWN0+0x4C)
+/* MAILBOX 0 access in Owner 0 area */
+/* Some addresses should ONLY be used by owner 0 */
+#define ARM_0_MAIL0_WRT  HW_REGISTER_RW(ARM_SBM_OWN0+0x80)  /* .. 0x8C (4 locations) */
+#define ARM_0_MAIL0_RD   HW_REGISTER_RW(ARM_SBM_OWN0+0x80)  /* .. 0x8C (4 locations) Normal read */
+#define ARM_0_MAIL0_POL  HW_REGISTER_RW(ARM_SBM_OWN0+0x90)  /* none-pop read */
+#define ARM_0_MAIL0_SND  HW_REGISTER_RW(ARM_SBM_OWN0+0x94)  /* Sender read (only LS 2 bits) */
+#define ARM_0_MAIL0_STA  HW_REGISTER_RW(ARM_SBM_OWN0+0x98)  /* Status read */
+#define ARM_0_MAIL0_CNF  HW_REGISTER_RW(ARM_SBM_OWN0+0x9C)  /* Config read/write */
+/* MAILBOX 1 access in Owner 0 area */
+/* Owner 0 should only WRITE to this mailbox */
+#define ARM_0_MAIL1_WRT  HW_REGISTER_RW(ARM_SBM_OWN0+0xA0)   /* .. 0xAC (4 locations) */
+/*#define ARM_0_MAIL1_RD   HW_REGISTER_RW(ARM_SBM_OWN0+0xA0) */ /* DO NOT USE THIS !!!!! */
+/*#define ARM_0_MAIL1_POL  HW_REGISTER_RW(ARM_SBM_OWN0+0xB0) */ /* DO NOT USE THIS !!!!! */
+/*#define ARM_0_MAIL1_SND  HW_REGISTER_RW(ARM_SBM_OWN0+0xB4) */ /* DO NOT USE THIS !!!!! */
+#define ARM_0_MAIL1_STA  HW_REGISTER_RW(ARM_SBM_OWN0+0xB8)   /* Status read */
+/*#define ARM_0_MAIL1_CNF  HW_REGISTER_RW(ARM_SBM_OWN0+0xBC) */ /* DO NOT USE THIS !!!!! */
+/* General SEM, BELL, MAIL config/status */
+#define ARM_0_SEMCLRDBG   HW_REGISTER_RW(ARM_SBM_OWN0+0xE0)  /* semaphore clear/debug register */
+#define ARM_0_BELLCLRDBG  HW_REGISTER_RW(ARM_SBM_OWN0+0xE4)  /* Doorbells clear/debug register */
+#define ARM_0_ALL_IRQS    HW_REGISTER_RW(ARM_SBM_OWN0+0xF8)  /* ALL interrupts */
+#define ARM_0_MY_IRQS     HW_REGISTER_RW(ARM_SBM_OWN0+0xFC)  /* IRQS pending for owner 0 */
+
+/* Semaphores, Doorbells, Mailboxes Owner 1 */
+#define ARM_1_SEMS       HW_REGISTER_RW(ARM_SBM_OWN1+0x00)
+#define ARM_1_SEM0       HW_REGISTER_RW(ARM_SBM_OWN1+0x00)
+#define ARM_1_SEM1       HW_REGISTER_RW(ARM_SBM_OWN1+0x04)
+#define ARM_1_SEM2       HW_REGISTER_RW(ARM_SBM_OWN1+0x08)
+#define ARM_1_SEM3       HW_REGISTER_RW(ARM_SBM_OWN1+0x0C)
+#define ARM_1_SEM4       HW_REGISTER_RW(ARM_SBM_OWN1+0x10)
+#define ARM_1_SEM5       HW_REGISTER_RW(ARM_SBM_OWN1+0x14)
+#define ARM_1_SEM6       HW_REGISTER_RW(ARM_SBM_OWN1+0x18)
+#define ARM_1_SEM7       HW_REGISTER_RW(ARM_SBM_OWN1+0x1C)
+#define ARM_1_BELL0      HW_REGISTER_RW(ARM_SBM_OWN1+0x40)
+#define ARM_1_BELL1      HW_REGISTER_RW(ARM_SBM_OWN1+0x44)
+#define ARM_1_BELL2      HW_REGISTER_RW(ARM_SBM_OWN1+0x48)
+#define ARM_1_BELL3      HW_REGISTER_RW(ARM_SBM_OWN1+0x4C)
+/* MAILBOX 0 access in Owner 0 area */
+/* Owner 1 should only WRITE to this mailbox */
+#define ARM_1_MAIL0_WRT  HW_REGISTER_RW(ARM_SBM_OWN1+0x80)  /* .. 0x8C (4 locations) */
+/*#define ARM_1_MAIL0_RD  HW_REGISTER_RW(ARM_SBM_OWN1+0x80) */ /* DO NOT USE THIS !!!!! */
+/*#define ARM_1_MAIL0_POL HW_REGISTER_RW(ARM_SBM_OWN1+0x90) */ /* DO NOT USE THIS !!!!! */
+/*#define ARM_1_MAIL0_SND HW_REGISTER_RW(ARM_SBM_OWN1+0x94) */ /* DO NOT USE THIS !!!!! */
+#define ARM_1_MAIL0_STA  HW_REGISTER_RW(ARM_SBM_OWN1+0x98)  /* Status read */
+/*#define ARM_1_MAIL0_CNF HW_REGISTER_RW(ARM_SBM_OWN1+0x9C) */ /* DO NOT USE THIS !!!!! */
+/* MAILBOX 1 access in Owner 0 area */
+#define ARM_1_MAIL1_WRT  HW_REGISTER_RW(ARM_SBM_OWN1+0xA0)  /* .. 0xAC (4 locations) */
+#define ARM_1_MAIL1_RD   HW_REGISTER_RW(ARM_SBM_OWN1+0xA0)  /* .. 0xAC (4 locations) Normal read */
+#define ARM_1_MAIL1_POL  HW_REGISTER_RW(ARM_SBM_OWN1+0xB0)  /* none-pop read */
+#define ARM_1_MAIL1_SND  HW_REGISTER_RW(ARM_SBM_OWN1+0xB4)  /* Sender read (only LS 2 bits) */
+#define ARM_1_MAIL1_STA  HW_REGISTER_RW(ARM_SBM_OWN1+0xB8)  /* Status read */
+#define ARM_1_MAIL1_CNF  HW_REGISTER_RW(ARM_SBM_OWN1+0xBC)
+/* General SEM, BELL, MAIL config/status */
+#define ARM_1_SEMCLRDBG   HW_REGISTER_RW(ARM_SBM_OWN1+0xE0)  /* semaphore clear/debug register */
+#define ARM_1_BELLCLRDBG  HW_REGISTER_RW(ARM_SBM_OWN1+0xE4)  /* Doorbells clear/debug register */
+#define ARM_1_MY_IRQS     HW_REGISTER_RW(ARM_SBM_OWN1+0xFC)  /* IRQS pending for owner 1 */
+#define ARM_1_ALL_IRQS    HW_REGISTER_RW(ARM_SBM_OWN1+0xF8)  /* ALL interrupts */
+
+/* Semaphores, Doorbells, Mailboxes Owner 2 */
+#define ARM_2_SEMS       HW_REGISTER_RW(ARM_SBM_OWN2+0x00)
+#define ARM_2_SEM0       HW_REGISTER_RW(ARM_SBM_OWN2+0x00)
+#define ARM_2_SEM1       HW_REGISTER_RW(ARM_SBM_OWN2+0x04)
+#define ARM_2_SEM2       HW_REGISTER_RW(ARM_SBM_OWN2+0x08)
+#define ARM_2_SEM3       HW_REGISTER_RW(ARM_SBM_OWN2+0x0C)
+#define ARM_2_SEM4       HW_REGISTER_RW(ARM_SBM_OWN2+0x10)
+#define ARM_2_SEM5       HW_REGISTER_RW(ARM_SBM_OWN2+0x14)
+#define ARM_2_SEM6       HW_REGISTER_RW(ARM_SBM_OWN2+0x18)
+#define ARM_2_SEM7       HW_REGISTER_RW(ARM_SBM_OWN2+0x1C)
+#define ARM_2_BELL0      HW_REGISTER_RW(ARM_SBM_OWN2+0x40)
+#define ARM_2_BELL1      HW_REGISTER_RW(ARM_SBM_OWN2+0x44)
+#define ARM_2_BELL2      HW_REGISTER_RW(ARM_SBM_OWN2+0x48)
+#define ARM_2_BELL3      HW_REGISTER_RW(ARM_SBM_OWN2+0x4C)
+/* MAILBOX 0 access in Owner 2 area */
+/* Owner 2 should only WRITE to this mailbox */
+#define ARM_2_MAIL0_WRT  HW_REGISTER_RW(ARM_SBM_OWN2+0x80)   /* .. 0x8C (4 locations) */
+/*#define ARM_2_MAIL0_RD  HW_REGISTER_RW(ARM_SBM_OWN2+0x80)  */ /* DO NOT USE THIS !!!!! */
+/*#define ARM_2_MAIL0_POL HW_REGISTER_RW(ARM_SBM_OWN2+0x90)  */ /* DO NOT USE THIS !!!!! */
+/*#define ARM_2_MAIL0_SND HW_REGISTER_RW(ARM_SBM_OWN2+0x94)  */ /* DO NOT USE THIS !!!!! */
+#define ARM_2_MAIL0_STA  HW_REGISTER_RW(ARM_SBM_OWN2+0x98)   /* Status read */
+/*#define ARM_2_MAIL0_CNF HW_REGISTER_RW(ARM_SBM_OWN2+0x9C)  */ /* DO NOT USE THIS !!!!! */
+/* MAILBOX 1 access in Owner 2 area */
+/* Owner 2 should only WRITE to this mailbox */
+#define ARM_2_MAIL1_WRT  HW_REGISTER_RW(ARM_SBM_OWN2+0xA0)   /* .. 0xAC (4 locations) */
+/*#define ARM_2_MAIL1_RD   HW_REGISTER_RW(ARM_SBM_OWN2+0xA0) */ /* DO NOT USE THIS !!!!! */
+/*#define ARM_2_MAIL1_POL  HW_REGISTER_RW(ARM_SBM_OWN2+0xB0) */ /* DO NOT USE THIS !!!!! */
+/*#define ARM_2_MAIL1_SND  HW_REGISTER_RW(ARM_SBM_OWN2+0xB4) */ /* DO NOT USE THIS !!!!! */
+#define ARM_2_MAIL1_STA  HW_REGISTER_RW(ARM_SBM_OWN2+0xB8)   /* Status read */
+/*#define ARM_2_MAIL1_CNF  HW_REGISTER_RW(ARM_SBM_OWN2+0xBC) */ /* DO NOT USE THIS !!!!! */
+/* General SEM, BELL, MAIL config/status */
+#define ARM_2_SEMCLRDBG   HW_REGISTER_RW(ARM_SBM_OWN2+0xE0)  /* semaphore clear/debug register */
+#define ARM_2_BELLCLRDBG  HW_REGISTER_RW(ARM_SBM_OWN2+0xE4)  /* Doorbells clear/debug register */
+#define ARM_2_MY_IRQS     HW_REGISTER_RW(ARM_SBM_OWN2+0xFC)  /* IRQS pending for owner 2 */
+#define ARM_2_ALL_IRQS    HW_REGISTER_RW(ARM_SBM_OWN2+0xF8)  /* ALL interrupts */
+
+/* Semaphores, Doorbells, Mailboxes Owner 3 */
+#define ARM_3_SEMS       HW_REGISTER_RW(ARM_SBM_OWN3+0x00)
+#define ARM_3_SEM0       HW_REGISTER_RW(ARM_SBM_OWN3+0x00)
+#define ARM_3_SEM1       HW_REGISTER_RW(ARM_SBM_OWN3+0x04)
+#define ARM_3_SEM2       HW_REGISTER_RW(ARM_SBM_OWN3+0x08)
+#define ARM_3_SEM3       HW_REGISTER_RW(ARM_SBM_OWN3+0x0C)
+#define ARM_3_SEM4       HW_REGISTER_RW(ARM_SBM_OWN3+0x10)
+#define ARM_3_SEM5       HW_REGISTER_RW(ARM_SBM_OWN3+0x14)
+#define ARM_3_SEM6       HW_REGISTER_RW(ARM_SBM_OWN3+0x18)
+#define ARM_3_SEM7       HW_REGISTER_RW(ARM_SBM_OWN3+0x1C)
+#define ARM_3_BELL0      HW_REGISTER_RW(ARM_SBM_OWN3+0x40)
+#define ARM_3_BELL1      HW_REGISTER_RW(ARM_SBM_OWN3+0x44)
+#define ARM_3_BELL2      HW_REGISTER_RW(ARM_SBM_OWN3+0x48)
+#define ARM_3_BELL3      HW_REGISTER_RW(ARM_SBM_OWN3+0x4C)
+/* MAILBOX 0 access in Owner 3 area */
+/* Owner 3 should only WRITE to this mailbox */
+#define ARM_3_MAIL0_WRT  HW_REGISTER_RW(ARM_SBM_OWN3+0x80)   /* .. 0x8C (4 locations) */
+/*#define ARM_3_MAIL0_RD  HW_REGISTER_RW(ARM_SBM_OWN3+0x80)  */ /* DO NOT USE THIS !!!!! */
+/*#define ARM_3_MAIL0_POL HW_REGISTER_RW(ARM_SBM_OWN3+0x90)  */ /* DO NOT USE THIS !!!!! */
+/*#define ARM_3_MAIL0_SND HW_REGISTER_RW(ARM_SBM_OWN3+0x94)  */ /* DO NOT USE THIS !!!!! */
+#define ARM_3_MAIL0_STA HW_REGISTER_RW(ARM_SBM_OWN3+0x98)    /* Status read */
+/*#define ARM_3_MAIL0_CNF HW_REGISTER_RW(ARM_SBM_OWN3+0x9C)  */ /* DO NOT USE THIS !!!!! */
+/* MAILBOX 1 access in Owner 3 area */
+/* Owner 3 should only WRITE to this mailbox */
+#define ARM_3_MAIL1_WRT  HW_REGISTER_RW(ARM_SBM_OWN3+0xA0)   /* .. 0xAC (4 locations) */
+/*#define ARM_3_MAIL1_RD   HW_REGISTER_RW(ARM_SBM_OWN3+0xA0) */ /* DO NOT USE THIS !!!!! */
+/*#define ARM_3_MAIL1_POL  HW_REGISTER_RW(ARM_SBM_OWN3+0xB0) */ /* DO NOT USE THIS !!!!! */
+/*#define ARM_3_MAIL1_SND  HW_REGISTER_RW(ARM_SBM_OWN3+0xB4) */ /* DO NOT USE THIS !!!!! */
+#define ARM_3_MAIL1_STA  HW_REGISTER_RW(ARM_SBM_OWN3+0xB8)   /* Status read */
+/*#define ARM_3_MAIL1_CNF  HW_REGISTER_RW(ARM_SBM_OWN3+0xBC) */ /* DO NOT USE THIS !!!!! */
+/* General SEM, BELL, MAIL config/status */
+#define ARM_3_SEMCLRDBG   HW_REGISTER_RW(ARM_SBM_OWN3+0xE0)  /* semaphore clear/debug register */
+#define ARM_3_BELLCLRDBG  HW_REGISTER_RW(ARM_SBM_OWN3+0xE4)  /* Doorbells clear/debug register */
+#define ARM_3_MY_IRQS     HW_REGISTER_RW(ARM_SBM_OWN3+0xFC)  /* IRQS pending for owner 3 */
+#define ARM_3_ALL_IRQS    HW_REGISTER_RW(ARM_SBM_OWN3+0xF8)  /* ALL interrupts */
+
+
+
+/*  Mailbox flags. Valid for all owners */
+
+/* Mailbox status register (...0x98) */
+#define ARM_MS_FULL       0x80000000
+#define ARM_MS_EMPTY      0x40000000
+#define ARM_MS_LEVEL      0x400000FF /* Max. value depdnds on mailbox depth parameter */
+
+/* MAILBOX config/status register (...0x9C) */
+/* ANY write to this register clears the error bits! */
+#define ARM_MC_IHAVEDATAIRQEN    0x00000001 /* mailbox irq enable:  has data */
+#define ARM_MC_IHAVESPACEIRQEN   0x00000002 /* mailbox irq enable:  has space */
+#define ARM_MC_OPPISEMPTYIRQEN   0x00000004 /* mailbox irq enable: Opp. is empty */
+#define ARM_MC_MAIL_CLEAR        0x00000008 /* mailbox clear write 1, then  0 */
+#define ARM_MC_IHAVEDATAIRQPEND  0x00000010 /* mailbox irq pending:  has space */
+#define ARM_MC_IHAVESPACEIRQPEND 0x00000020 /* mailbox irq pending: Opp. is empty */
+#define ARM_MC_OPPISEMPTYIRQPEND 0x00000040 /* mailbox irq pending */
+/* Bit 7 is unused */
+#define ARM_MC_ERRNOOWN   0x00000100 /* error : none owner read from mailbox */
+#define ARM_MC_ERROVERFLW 0x00000200 /* error : write to fill mailbox */
+#define ARM_MC_ERRUNDRFLW 0x00000400 /* error : read from empty mailbox */
+
+/* Semaphore clear/debug register (...0xE0) */
+#define ARM_SD_OWN0      0x00000003  /* Owner of sem 0 */
+#define ARM_SD_OWN1      0x0000000C  /* Owner of sem 1 */
+#define ARM_SD_OWN2      0x00000030  /* Owner of sem 2 */
+#define ARM_SD_OWN3      0x000000C0  /* Owner of sem 3 */
+#define ARM_SD_OWN4      0x00000300  /* Owner of sem 4 */
+#define ARM_SD_OWN5      0x00000C00  /* Owner of sem 5 */
+#define ARM_SD_OWN6      0x00003000  /* Owner of sem 6 */
+#define ARM_SD_OWN7      0x0000C000  /* Owner of sem 7 */
+#define ARM_SD_SEM0      0x00010000  /* Status of sem 0 */
+#define ARM_SD_SEM1      0x00020000  /* Status of sem 1 */
+#define ARM_SD_SEM2      0x00040000  /* Status of sem 2 */
+#define ARM_SD_SEM3      0x00080000  /* Status of sem 3 */
+#define ARM_SD_SEM4      0x00100000  /* Status of sem 4 */
+#define ARM_SD_SEM5      0x00200000  /* Status of sem 5 */
+#define ARM_SD_SEM6      0x00400000  /* Status of sem 6 */
+#define ARM_SD_SEM7      0x00800000  /* Status of sem 7 */
+
+/* Doorbells clear/debug register (...0xE4) */
+#define ARM_BD_OWN0      0x00000003  /* Owner of doorbell 0 */
+#define ARM_BD_OWN1      0x0000000C  /* Owner of doorbell 1 */
+#define ARM_BD_OWN2      0x00000030  /* Owner of doorbell 2 */
+#define ARM_BD_OWN3      0x000000C0  /* Owner of doorbell 3 */
+#define ARM_BD_BELL0     0x00000100  /* Status of doorbell 0 */
+#define ARM_BD_BELL1     0x00000200  /* Status of doorbell 1 */
+#define ARM_BD_BELL2     0x00000400  /* Status of doorbell 2 */
+#define ARM_BD_BELL3     0x00000800  /* Status of doorbell 3 */
+
+/* MY IRQS register (...0xF8) */
+#define ARM_MYIRQ_BELL   0x00000001  /* This owner has a doorbell IRQ */
+#define ARM_MYIRQ_MAIL   0x00000002  /* This owner has a mailbox  IRQ */
+
+/* ALL IRQS register (...0xF8) */
+#define ARM_AIS_BELL0 0x00000001  /* Doorbell 0 IRQ pending */
+#define ARM_AIS_BELL1 0x00000002  /* Doorbell 1 IRQ pending */
+#define ARM_AIS_BELL2 0x00000004  /* Doorbell 2 IRQ pending */
+#define ARM_AIS_BELL3 0x00000008  /* Doorbell 3 IRQ pending */
+#define ARM_AIS0_HAVEDATA 0x00000010  /* MAIL 0 has data IRQ pending */
+#define ARM_AIS0_HAVESPAC 0x00000020  /* MAIL 0 has space IRQ pending */
+#define ARM_AIS0_OPPEMPTY 0x00000040  /* MAIL 0 opposite is empty IRQ */
+#define ARM_AIS1_HAVEDATA 0x00000080  /* MAIL 1 has data IRQ pending */
+#define ARM_AIS1_HAVESPAC 0x00000100  /* MAIL 1 has space IRQ pending */
+#define ARM_AIS1_OPPEMPTY 0x00000200  /* MAIL 1 opposite is empty IRQ */
+/* Note   that bell-0, bell-1 and MAIL0 IRQ go only to the ARM */
+/* Whilst that bell-2, bell-3 and MAIL1 IRQ go only to the VC */
+/* */
+/* ARM JTAG BASH */
+/* */
+#define AJB_BASE 0x7e2000c0
+
+#define AJBCONF HW_REGISTER_RW(AJB_BASE+0x00)
+#define   AJB_BITS0    0x000000
+#define   AJB_BITS4    0x000004
+#define   AJB_BITS8    0x000008
+#define   AJB_BITS12   0x00000C
+#define   AJB_BITS16   0x000010
+#define   AJB_BITS20   0x000014
+#define   AJB_BITS24   0x000018
+#define   AJB_BITS28   0x00001C
+#define   AJB_BITS32   0x000020
+#define   AJB_BITS34   0x000022
+#define   AJB_OUT_MS   0x000040
+#define   AJB_OUT_LS   0x000000
+#define   AJB_INV_CLK  0x000080
+#define   AJB_D0_RISE  0x000100
+#define   AJB_D0_FALL  0x000000
+#define   AJB_D1_RISE  0x000200
+#define   AJB_D1_FALL  0x000000
+#define   AJB_IN_RISE  0x000400
+#define   AJB_IN_FALL  0x000000
+#define   AJB_ENABLE   0x000800
+#define   AJB_HOLD0    0x000000
+#define   AJB_HOLD1    0x001000
+#define   AJB_HOLD2    0x002000
+#define   AJB_HOLD3    0x003000
+#define   AJB_RESETN   0x004000
+#define   AJB_CLKSHFT  16
+#define   AJB_BUSY     0x80000000
+#define AJBTMS HW_REGISTER_RW(AJB_BASE+0x04)
+#define AJBTDI HW_REGISTER_RW(AJB_BASE+0x08)
+#define AJBTDO HW_REGISTER_RW(AJB_BASE+0x0c)
+
+#endif

arch/arm/mach-bcm2708/include/mach/arm_power.h

@@ -0,0 +1,62 @@
+/*
+ *  linux/arch/arm/mach-bcm2708/include/mach/arm_power.h
+ *
+ *  Copyright (C) 2010 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#ifndef _ARM_POWER_H
+#define _ARM_POWER_H
+
+/* Use meaningful names on each side */
+#ifdef __VIDEOCORE__
+#define PREFIX(x) ARM_##x
+#else
+#define PREFIX(x) BCM_##x
+#endif
+
+enum {
+	PREFIX(POWER_SDCARD_BIT),
+	PREFIX(POWER_UART_BIT),
+	PREFIX(POWER_MINIUART_BIT),
+	PREFIX(POWER_USB_BIT),
+	PREFIX(POWER_I2C0_BIT),
+	PREFIX(POWER_I2C1_BIT),
+	PREFIX(POWER_I2C2_BIT),
+	PREFIX(POWER_SPI_BIT),
+	PREFIX(POWER_CCP2TX_BIT),
+	PREFIX(POWER_DSI_BIT),
+
+	PREFIX(POWER_MAX)
+};
+
+enum {
+	PREFIX(POWER_SDCARD) = (1 << PREFIX(POWER_SDCARD_BIT)),
+	PREFIX(POWER_UART) = (1 << PREFIX(POWER_UART_BIT)),
+	PREFIX(POWER_MINIUART) = (1 << PREFIX(POWER_MINIUART_BIT)),
+	PREFIX(POWER_USB) = (1 << PREFIX(POWER_USB_BIT)),
+	PREFIX(POWER_I2C0) = (1 << PREFIX(POWER_I2C0_BIT)),
+	PREFIX(POWER_I2C1_MASK) = (1 << PREFIX(POWER_I2C1_BIT)),
+	PREFIX(POWER_I2C2_MASK) = (1 << PREFIX(POWER_I2C2_BIT)),
+	PREFIX(POWER_SPI_MASK) = (1 << PREFIX(POWER_SPI_BIT)),
+	PREFIX(POWER_CCP2TX_MASK) = (1 << PREFIX(POWER_CCP2TX_BIT)),
+	PREFIX(POWER_DSI) = (1 << PREFIX(POWER_DSI_BIT)),
+
+	PREFIX(POWER_MASK) = (1 << PREFIX(POWER_MAX)) - 1,
+	PREFIX(POWER_NONE) = 0
+};
+
+#endif

arch/arm/mach-bcm2708/include/mach/clkdev.h

@@ -0,0 +1,7 @@
+#ifndef __ASM_MACH_CLKDEV_H
+#define __ASM_MACH_CLKDEV_H
+
+#define __clk_get(clk) ({ 1; })
+#define __clk_put(clk) do { } while (0)
+
+#endif

arch/arm/mach-bcm2708/include/mach/debug-macro.S

@@ -0,0 +1,22 @@
+/* arch/arm/mach-bcm2708/include/mach/debug-macro.S
+ *
+ * Debugging macro include header
+ *
+ *  Copyright (C) 2010 Broadcom
+ *  Copyright (C) 1994-1999 Russell King
+ *  Moved from linux/arch/arm/kernel/debug.S by Ben Dooks
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+*/
+
+#include <mach/platform.h>
+
+		.macro	addruart, rp, rv, tmp
+		ldr	\rp, =UART0_BASE
+		ldr	\rv, =IO_ADDRESS(UART0_BASE)
+		.endm
+
+#include <debug/pl01x.S>

arch/arm/mach-bcm2708/include/mach/dma.h

@@ -0,0 +1,94 @@
+/*
+ *  linux/arch/arm/mach-bcm2708/include/mach/dma.h
+ *
+ *  Copyright (C) 2010 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+
+#ifndef _MACH_BCM2708_DMA_H
+#define _MACH_BCM2708_DMA_H
+
+#define BCM_DMAMAN_DRIVER_NAME "bcm2708_dma"
+
+/* DMA CS Control and Status bits */
+#define BCM2708_DMA_ACTIVE	(1 << 0)
+#define BCM2708_DMA_INT		(1 << 2)
+#define BCM2708_DMA_ISPAUSED	(1 << 4)  /* Pause requested or not active */
+#define BCM2708_DMA_ISHELD	(1 << 5)  /* Is held by DREQ flow control */
+#define BCM2708_DMA_ERR		(1 << 8)
+#define BCM2708_DMA_ABORT	(1 << 30) /* stop current CB, go to next, WO */
+#define BCM2708_DMA_RESET	(1 << 31) /* WO, self clearing */
+
+/* DMA control block "info" field bits */
+#define BCM2708_DMA_INT_EN	(1 << 0)
+#define BCM2708_DMA_TDMODE	(1 << 1)
+#define BCM2708_DMA_WAIT_RESP	(1 << 3)
+#define BCM2708_DMA_D_INC	(1 << 4)
+#define BCM2708_DMA_D_WIDTH	(1 << 5)
+#define BCM2708_DMA_D_DREQ	(1 << 6)
+#define BCM2708_DMA_S_INC	(1 << 8)
+#define BCM2708_DMA_S_WIDTH	(1 << 9)
+#define BCM2708_DMA_S_DREQ	(1 << 10)
+
+#define	BCM2708_DMA_BURST(x)	(((x)&0xf) << 12)
+#define	BCM2708_DMA_PER_MAP(x)	((x) << 16)
+#define	BCM2708_DMA_WAITS(x)	(((x)&0x1f) << 21)
+
+#define BCM2708_DMA_DREQ_EMMC	11
+#define BCM2708_DMA_DREQ_SDHOST	13
+
+#define BCM2708_DMA_CS		0x00 /* Control and Status */
+#define BCM2708_DMA_ADDR	0x04
+/* the current control block appears in the following registers - read only */
+#define BCM2708_DMA_INFO	0x08
+#define BCM2708_DMA_SOURCE_AD	0x0c
+#define BCM2708_DMA_DEST_AD	0x10
+#define BCM2708_DMA_NEXTCB	0x1C
+#define BCM2708_DMA_DEBUG	0x20
+
+#define BCM2708_DMA4_CS		(BCM2708_DMA_CHAN(4)+BCM2708_DMA_CS)
+#define BCM2708_DMA4_ADDR	(BCM2708_DMA_CHAN(4)+BCM2708_DMA_ADDR)
+
+#define BCM2708_DMA_TDMODE_LEN(w, h) ((h) << 16 | (w))
+
+struct bcm2708_dma_cb {
+	unsigned long info;
+	unsigned long src;
+	unsigned long dst;
+	unsigned long length;
+	unsigned long stride;
+	unsigned long next;
+	unsigned long pad[2];
+};
+struct scatterlist;
+
+extern int bcm_sg_suitable_for_dma(struct scatterlist *sg_ptr, int sg_len);
+extern void bcm_dma_start(void __iomem *dma_chan_base,
+			  dma_addr_t control_block);
+extern void bcm_dma_wait_idle(void __iomem *dma_chan_base);
+extern bool bcm_dma_is_busy(void __iomem *dma_chan_base);
+extern int /*rc*/ bcm_dma_abort(void __iomem *dma_chan_base);
+
+/* When listing features we can ask for when allocating DMA channels give
+   those with higher priority smaller ordinal numbers */
+#define BCM_DMA_FEATURE_FAST_ORD 0
+#define BCM_DMA_FEATURE_BULK_ORD 1
+#define BCM_DMA_FEATURE_NORMAL_ORD 2
+#define BCM_DMA_FEATURE_LITE_ORD 3
+#define BCM_DMA_FEATURE_FAST	 (1<<BCM_DMA_FEATURE_FAST_ORD)
+#define BCM_DMA_FEATURE_BULK	 (1<<BCM_DMA_FEATURE_BULK_ORD)
+#define BCM_DMA_FEATURE_NORMAL	 (1<<BCM_DMA_FEATURE_NORMAL_ORD)
+#define BCM_DMA_FEATURE_LITE	 (1<<BCM_DMA_FEATURE_LITE_ORD)
+#define BCM_DMA_FEATURE_COUNT	 4
+
+/* return channel no or -ve error */
+extern int bcm_dma_chan_alloc(unsigned preferred_feature_set,
+			      void __iomem **out_dma_base, int *out_dma_irq);
+extern int bcm_dma_chan_free(int channel);
+
+
+#endif /* _MACH_BCM2708_DMA_H */

arch/arm/mach-bcm2708/include/mach/entry-macro.S

@@ -0,0 +1,69 @@
+/*
+ * arch/arm/mach-bcm2708/include/mach/entry-macro.S
+ *
+ * Low-level IRQ helper macros for BCM2708 platforms
+ *
+ *  Copyright (C) 2010 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+#include <mach/hardware.h>
+
+		.macro	disable_fiq
+		.endm
+
+		.macro  get_irqnr_preamble, base, tmp
+		ldr	\base, =IO_ADDRESS(ARMCTRL_IC_BASE)
+		.endm
+
+		.macro  arch_ret_to_user, tmp1, tmp2
+		.endm
+
+		.macro	get_irqnr_and_base, irqnr, irqstat, base, tmp
+		/* get masked status */
+		ldr	\irqstat, [\base, #(ARM_IRQ_PEND0 - ARMCTRL_IC_BASE)]
+		mov	\irqnr, #(ARM_IRQ0_BASE + 31)
+		and	\tmp, \irqstat, #0x300		 @ save bits 8 and 9
+		/* clear bits 8 and 9, and test */
+		bics	\irqstat, \irqstat, #0x300
+		bne	1010f
+
+		tst	\tmp, #0x100
+		ldrne	\irqstat, [\base, #(ARM_IRQ_PEND1 - ARMCTRL_IC_BASE)]
+		movne \irqnr, #(ARM_IRQ1_BASE + 31)
+		@ Mask out the interrupts also present in PEND0 - see SW-5809
+		bicne \irqstat, #((1<<7) | (1<<9) | (1<<10))
+		bicne \irqstat, #((1<<18) | (1<<19))
+		bne	1010f
+
+		tst	\tmp, #0x200
+		ldrne \irqstat, [\base, #(ARM_IRQ_PEND2 - ARMCTRL_IC_BASE)]
+		movne \irqnr, #(ARM_IRQ2_BASE + 31)
+		@ Mask out the interrupts also present in PEND0 - see SW-5809
+		bicne \irqstat, #((1<<21) | (1<<22) | (1<<23) | (1<<24) | (1<<25))
+		bicne \irqstat, #((1<<30))
+		beq 1020f
+
+1010:
+		@ For non-zero x, LSB(x) = 31 - CLZ(x^(x-1))
+		@ N.B. CLZ is an ARM5 instruction.
+		sub	\tmp, \irqstat, #1
+		eor	\irqstat, \irqstat, \tmp
+		clz	\tmp, \irqstat
+		sub	\irqnr, \tmp
+
+1020:	@ EQ will be set if no irqs pending
+
+		.endm

arch/arm/mach-bcm2708/include/mach/frc.h

@@ -0,0 +1,38 @@
+/*
+ *  arch/arm/mach-bcm2708/include/mach/timex.h
+ *
+ *  BCM2708 free running counter (timer)
+ *
+ *  Copyright (C) 2010 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#ifndef _MACH_FRC_H
+#define _MACH_FRC_H
+
+#define FRC_TICK_RATE		(1000000)
+
+/*! Free running counter incrementing at the CLOCK_TICK_RATE
+    (slightly faster than frc_clock_ticks63()
+ */
+extern unsigned long frc_clock_ticks32(void);
+
+/*! Free running counter incrementing at the CLOCK_TICK_RATE
+ *  Note - top bit should be ignored (see cnt32_to_63)
+ */
+extern unsigned long long frc_clock_ticks63(void);
+
+#endif

arch/arm/mach-bcm2708/include/mach/gpio.h

@@ -0,0 +1,17 @@
+/*
+ * arch/arm/mach-bcm2708/include/mach/gpio.h
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifndef __ASM_ARCH_GPIO_H
+#define __ASM_ARCH_GPIO_H
+
+#define BCM2708_NR_GPIOS 54 // number of gpio lines
+
+#define gpio_to_irq(x)	((x) + GPIO_IRQ_START)
+#define irq_to_gpio(x)	((x) - GPIO_IRQ_START)
+
+#endif

arch/arm/mach-bcm2708/include/mach/hardware.h

@@ -0,0 +1,28 @@
+/*
+ *  arch/arm/mach-bcm2708/include/mach/hardware.h
+ *
+ *  This file contains the hardware definitions of the BCM2708 devices.
+ *
+ *  Copyright (C) 2010 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+#ifndef __ASM_ARCH_HARDWARE_H
+#define __ASM_ARCH_HARDWARE_H
+
+#include <asm/sizes.h>
+#include <mach/platform.h>
+
+#endif

arch/arm/mach-bcm2708/include/mach/io.h

@@ -0,0 +1,27 @@
+/*
+ *  arch/arm/mach-bcm2708/include/mach/io.h
+ *
+ *  Copyright (C) 2003 ARM Limited
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+#ifndef __ASM_ARM_ARCH_IO_H
+#define __ASM_ARM_ARCH_IO_H
+
+#define IO_SPACE_LIMIT 0xffffffff
+
+#define __io(a)		__typesafe_io(a)
+
+#endif

arch/arm/mach-bcm2708/include/mach/irqs.h

@@ -0,0 +1,197 @@
+/*
+ *  arch/arm/mach-bcm2708/include/mach/irqs.h
+ *
+ *  Copyright (C) 2010 Broadcom
+ *  Copyright (C) 2003 ARM Limited
+ *  Copyright (C) 2000 Deep Blue Solutions Ltd.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#ifndef _BCM2708_IRQS_H_
+#define _BCM2708_IRQS_H_
+
+#include <mach/platform.h>
+
+/*
+ *  IRQ interrupts definitions are the same as the INT definitions
+ *  held within platform.h
+ */
+#define IRQ_ARMCTRL_START     0
+#define IRQ_TIMER0            (IRQ_ARMCTRL_START + INTERRUPT_TIMER0)
+#define IRQ_TIMER1            (IRQ_ARMCTRL_START + INTERRUPT_TIMER1)
+#define IRQ_TIMER2            (IRQ_ARMCTRL_START + INTERRUPT_TIMER2)
+#define IRQ_TIMER3            (IRQ_ARMCTRL_START + INTERRUPT_TIMER3)
+#define IRQ_CODEC0            (IRQ_ARMCTRL_START + INTERRUPT_CODEC0)
+#define IRQ_CODEC1            (IRQ_ARMCTRL_START + INTERRUPT_CODEC1)
+#define IRQ_CODEC2            (IRQ_ARMCTRL_START + INTERRUPT_CODEC2)
+#define IRQ_JPEG              (IRQ_ARMCTRL_START + INTERRUPT_JPEG)
+#define IRQ_ISP               (IRQ_ARMCTRL_START + INTERRUPT_ISP)
+#define IRQ_USB               (IRQ_ARMCTRL_START + INTERRUPT_USB)
+#define IRQ_3D                (IRQ_ARMCTRL_START + INTERRUPT_3D)
+#define IRQ_TRANSPOSER        (IRQ_ARMCTRL_START + INTERRUPT_TRANSPOSER)
+#define IRQ_MULTICORESYNC0    (IRQ_ARMCTRL_START + INTERRUPT_MULTICORESYNC0)
+#define IRQ_MULTICORESYNC1    (IRQ_ARMCTRL_START + INTERRUPT_MULTICORESYNC1)
+#define IRQ_MULTICORESYNC2    (IRQ_ARMCTRL_START + INTERRUPT_MULTICORESYNC2)
+#define IRQ_MULTICORESYNC3    (IRQ_ARMCTRL_START + INTERRUPT_MULTICORESYNC3)
+#define IRQ_DMA0              (IRQ_ARMCTRL_START + INTERRUPT_DMA0)
+#define IRQ_DMA1              (IRQ_ARMCTRL_START + INTERRUPT_DMA1)
+#define IRQ_DMA2              (IRQ_ARMCTRL_START + INTERRUPT_DMA2)
+#define IRQ_DMA3              (IRQ_ARMCTRL_START + INTERRUPT_DMA3)
+#define IRQ_DMA4              (IRQ_ARMCTRL_START + INTERRUPT_DMA4)
+#define IRQ_DMA5              (IRQ_ARMCTRL_START + INTERRUPT_DMA5)
+#define IRQ_DMA6              (IRQ_ARMCTRL_START + INTERRUPT_DMA6)
+#define IRQ_DMA7              (IRQ_ARMCTRL_START + INTERRUPT_DMA7)
+#define IRQ_DMA8              (IRQ_ARMCTRL_START + INTERRUPT_DMA8)
+#define IRQ_DMA9              (IRQ_ARMCTRL_START + INTERRUPT_DMA9)
+#define IRQ_DMA10             (IRQ_ARMCTRL_START + INTERRUPT_DMA10)
+#define IRQ_DMA11             (IRQ_ARMCTRL_START + INTERRUPT_DMA11)
+#define IRQ_DMA12             (IRQ_ARMCTRL_START + INTERRUPT_DMA12)
+#define IRQ_AUX               (IRQ_ARMCTRL_START + INTERRUPT_AUX)
+#define IRQ_ARM               (IRQ_ARMCTRL_START + INTERRUPT_ARM)
+#define IRQ_VPUDMA            (IRQ_ARMCTRL_START + INTERRUPT_VPUDMA)
+#define IRQ_HOSTPORT          (IRQ_ARMCTRL_START + INTERRUPT_HOSTPORT)
+#define IRQ_VIDEOSCALER       (IRQ_ARMCTRL_START + INTERRUPT_VIDEOSCALER)
+#define IRQ_CCP2TX            (IRQ_ARMCTRL_START + INTERRUPT_CCP2TX)
+#define IRQ_SDC               (IRQ_ARMCTRL_START + INTERRUPT_SDC)
+#define IRQ_DSI0              (IRQ_ARMCTRL_START + INTERRUPT_DSI0)
+#define IRQ_AVE               (IRQ_ARMCTRL_START + INTERRUPT_AVE)
+#define IRQ_CAM0              (IRQ_ARMCTRL_START + INTERRUPT_CAM0)
+#define IRQ_CAM1              (IRQ_ARMCTRL_START + INTERRUPT_CAM1)
+#define IRQ_HDMI0             (IRQ_ARMCTRL_START + INTERRUPT_HDMI0)
+#define IRQ_HDMI1             (IRQ_ARMCTRL_START + INTERRUPT_HDMI1)
+#define IRQ_PIXELVALVE1       (IRQ_ARMCTRL_START + INTERRUPT_PIXELVALVE1)
+#define IRQ_I2CSPISLV         (IRQ_ARMCTRL_START + INTERRUPT_I2CSPISLV)
+#define IRQ_DSI1              (IRQ_ARMCTRL_START + INTERRUPT_DSI1)
+#define IRQ_PWA0              (IRQ_ARMCTRL_START + INTERRUPT_PWA0)
+#define IRQ_PWA1              (IRQ_ARMCTRL_START + INTERRUPT_PWA1)
+#define IRQ_CPR               (IRQ_ARMCTRL_START + INTERRUPT_CPR)
+#define IRQ_SMI               (IRQ_ARMCTRL_START + INTERRUPT_SMI)
+#define IRQ_GPIO0             (IRQ_ARMCTRL_START + INTERRUPT_GPIO0)
+#define IRQ_GPIO1             (IRQ_ARMCTRL_START + INTERRUPT_GPIO1)
+#define IRQ_GPIO2             (IRQ_ARMCTRL_START + INTERRUPT_GPIO2)
+#define IRQ_GPIO3             (IRQ_ARMCTRL_START + INTERRUPT_GPIO3)
+#define IRQ_I2C               (IRQ_ARMCTRL_START + INTERRUPT_I2C)
+#define IRQ_SPI               (IRQ_ARMCTRL_START + INTERRUPT_SPI)
+#define IRQ_I2SPCM            (IRQ_ARMCTRL_START + INTERRUPT_I2SPCM)
+#define IRQ_SDIO              (IRQ_ARMCTRL_START + INTERRUPT_SDIO)
+#define IRQ_UART              (IRQ_ARMCTRL_START + INTERRUPT_UART)
+#define IRQ_SLIMBUS           (IRQ_ARMCTRL_START + INTERRUPT_SLIMBUS)
+#define IRQ_VEC               (IRQ_ARMCTRL_START + INTERRUPT_VEC)
+#define IRQ_CPG               (IRQ_ARMCTRL_START + INTERRUPT_CPG)
+#define IRQ_RNG               (IRQ_ARMCTRL_START + INTERRUPT_RNG)
+#define IRQ_ARASANSDIO        (IRQ_ARMCTRL_START + INTERRUPT_ARASANSDIO)
+#define IRQ_AVSPMON           (IRQ_ARMCTRL_START + INTERRUPT_AVSPMON)
+
+#define IRQ_ARM_TIMER         (IRQ_ARMCTRL_START + INTERRUPT_ARM_TIMER)
+#define IRQ_ARM_MAILBOX       (IRQ_ARMCTRL_START + INTERRUPT_ARM_MAILBOX)
+#define IRQ_ARM_DOORBELL_0    (IRQ_ARMCTRL_START + INTERRUPT_ARM_DOORBELL_0)
+#define IRQ_ARM_DOORBELL_1    (IRQ_ARMCTRL_START + INTERRUPT_ARM_DOORBELL_1)
+#define IRQ_VPU0_HALTED       (IRQ_ARMCTRL_START + INTERRUPT_VPU0_HALTED)
+#define IRQ_VPU1_HALTED       (IRQ_ARMCTRL_START + INTERRUPT_VPU1_HALTED)
+#define IRQ_ILLEGAL_TYPE0     (IRQ_ARMCTRL_START + INTERRUPT_ILLEGAL_TYPE0)
+#define IRQ_ILLEGAL_TYPE1     (IRQ_ARMCTRL_START + INTERRUPT_ILLEGAL_TYPE1)
+#define IRQ_PENDING1          (IRQ_ARMCTRL_START + INTERRUPT_PENDING1)
+#define IRQ_PENDING2          (IRQ_ARMCTRL_START + INTERRUPT_PENDING2)
+
+#define FIQ_START             HARD_IRQS
+
+/*
+ *  FIQ interrupts definitions are the same as the INT definitions.
+ */
+#define FIQ_TIMER0            (FIQ_START+INTERRUPT_TIMER0)
+#define FIQ_TIMER1            (FIQ_START+INTERRUPT_TIMER1)
+#define FIQ_TIMER2            (FIQ_START+INTERRUPT_TIMER2)
+#define FIQ_TIMER3            (FIQ_START+INTERRUPT_TIMER3)
+#define FIQ_CODEC0            (FIQ_START+INTERRUPT_CODEC0)
+#define FIQ_CODEC1            (FIQ_START+INTERRUPT_CODEC1)
+#define FIQ_CODEC2            (FIQ_START+INTERRUPT_CODEC2)
+#define FIQ_JPEG              (FIQ_START+INTERRUPT_JPEG)
+#define FIQ_ISP               (FIQ_START+INTERRUPT_ISP)
+#define FIQ_USB               (FIQ_START+INTERRUPT_USB)
+#define FIQ_3D                (FIQ_START+INTERRUPT_3D)
+#define FIQ_TRANSPOSER        (FIQ_START+INTERRUPT_TRANSPOSER)
+#define FIQ_MULTICORESYNC0    (FIQ_START+INTERRUPT_MULTICORESYNC0)
+#define FIQ_MULTICORESYNC1    (FIQ_START+INTERRUPT_MULTICORESYNC1)
+#define FIQ_MULTICORESYNC2    (FIQ_START+INTERRUPT_MULTICORESYNC2)
+#define FIQ_MULTICORESYNC3    (FIQ_START+INTERRUPT_MULTICORESYNC3)
+#define FIQ_DMA0              (FIQ_START+INTERRUPT_DMA0)
+#define FIQ_DMA1              (FIQ_START+INTERRUPT_DMA1)
+#define FIQ_DMA2              (FIQ_START+INTERRUPT_DMA2)
+#define FIQ_DMA3              (FIQ_START+INTERRUPT_DMA3)
+#define FIQ_DMA4              (FIQ_START+INTERRUPT_DMA4)
+#define FIQ_DMA5              (FIQ_START+INTERRUPT_DMA5)
+#define FIQ_DMA6              (FIQ_START+INTERRUPT_DMA6)
+#define FIQ_DMA7              (FIQ_START+INTERRUPT_DMA7)
+#define FIQ_DMA8              (FIQ_START+INTERRUPT_DMA8)
+#define FIQ_DMA9              (FIQ_START+INTERRUPT_DMA9)
+#define FIQ_DMA10             (FIQ_START+INTERRUPT_DMA10)
+#define FIQ_DMA11             (FIQ_START+INTERRUPT_DMA11)
+#define FIQ_DMA12             (FIQ_START+INTERRUPT_DMA12)
+#define FIQ_AUX               (FIQ_START+INTERRUPT_AUX)
+#define FIQ_ARM               (FIQ_START+INTERRUPT_ARM)
+#define FIQ_VPUDMA            (FIQ_START+INTERRUPT_VPUDMA)
+#define FIQ_HOSTPORT          (FIQ_START+INTERRUPT_HOSTPORT)
+#define FIQ_VIDEOSCALER       (FIQ_START+INTERRUPT_VIDEOSCALER)
+#define FIQ_CCP2TX            (FIQ_START+INTERRUPT_CCP2TX)
+#define FIQ_SDC               (FIQ_START+INTERRUPT_SDC)
+#define FIQ_DSI0              (FIQ_START+INTERRUPT_DSI0)
+#define FIQ_AVE               (FIQ_START+INTERRUPT_AVE)
+#define FIQ_CAM0              (FIQ_START+INTERRUPT_CAM0)
+#define FIQ_CAM1              (FIQ_START+INTERRUPT_CAM1)
+#define FIQ_HDMI0             (FIQ_START+INTERRUPT_HDMI0)
+#define FIQ_HDMI1             (FIQ_START+INTERRUPT_HDMI1)
+#define FIQ_PIXELVALVE1       (FIQ_START+INTERRUPT_PIXELVALVE1)
+#define FIQ_I2CSPISLV         (FIQ_START+INTERRUPT_I2CSPISLV)
+#define FIQ_DSI1              (FIQ_START+INTERRUPT_DSI1)
+#define FIQ_PWA0              (FIQ_START+INTERRUPT_PWA0)
+#define FIQ_PWA1              (FIQ_START+INTERRUPT_PWA1)
+#define FIQ_CPR               (FIQ_START+INTERRUPT_CPR)
+#define FIQ_SMI               (FIQ_START+INTERRUPT_SMI)
+#define FIQ_GPIO0             (FIQ_START+INTERRUPT_GPIO0)
+#define FIQ_GPIO1             (FIQ_START+INTERRUPT_GPIO1)
+#define FIQ_GPIO2             (FIQ_START+INTERRUPT_GPIO2)
+#define FIQ_GPIO3             (FIQ_START+INTERRUPT_GPIO3)
+#define FIQ_I2C               (FIQ_START+INTERRUPT_I2C)
+#define FIQ_SPI               (FIQ_START+INTERRUPT_SPI)
+#define FIQ_I2SPCM            (FIQ_START+INTERRUPT_I2SPCM)
+#define FIQ_SDIO              (FIQ_START+INTERRUPT_SDIO)
+#define FIQ_UART              (FIQ_START+INTERRUPT_UART)
+#define FIQ_SLIMBUS           (FIQ_START+INTERRUPT_SLIMBUS)
+#define FIQ_VEC               (FIQ_START+INTERRUPT_VEC)
+#define FIQ_CPG               (FIQ_START+INTERRUPT_CPG)
+#define FIQ_RNG               (FIQ_START+INTERRUPT_RNG)
+#define FIQ_ARASANSDIO        (FIQ_START+INTERRUPT_ARASANSDIO)
+#define FIQ_AVSPMON           (FIQ_START+INTERRUPT_AVSPMON)
+
+#define FIQ_ARM_TIMER         (FIQ_START+INTERRUPT_ARM_TIMER)
+#define FIQ_ARM_MAILBOX       (FIQ_START+INTERRUPT_ARM_MAILBOX)
+#define FIQ_ARM_DOORBELL_0    (FIQ_START+INTERRUPT_ARM_DOORBELL_0)
+#define FIQ_ARM_DOORBELL_1    (FIQ_START+INTERRUPT_ARM_DOORBELL_1)
+#define FIQ_VPU0_HALTED       (FIQ_START+INTERRUPT_VPU0_HALTED)
+#define FIQ_VPU1_HALTED       (FIQ_START+INTERRUPT_VPU1_HALTED)
+#define FIQ_ILLEGAL_TYPE0     (FIQ_START+INTERRUPT_ILLEGAL_TYPE0)
+#define FIQ_ILLEGAL_TYPE1     (FIQ_START+INTERRUPT_ILLEGAL_TYPE1)
+#define FIQ_PENDING1          (FIQ_START+INTERRUPT_PENDING1)
+#define FIQ_PENDING2          (FIQ_START+INTERRUPT_PENDING2)
+
+#define HARD_IRQS	      (64 + 21)
+#define FIQ_IRQS        (64 + 21)
+#define GPIO_IRQ_START  (HARD_IRQS + FIQ_IRQS)
+#define GPIO_IRQS	      (32*5)
+#define SPARE_IRQS		  (64)
+#define NR_IRQS		      (HARD_IRQS+FIQ_IRQS+GPIO_IRQS+SPARE_IRQS)
+
+#endif /* _BCM2708_IRQS_H_ */

arch/arm/mach-bcm2708/include/mach/memory.h

@@ -0,0 +1,57 @@
+/*
+ *  arch/arm/mach-bcm2708/include/mach/memory.h
+ *
+ *  Copyright (C) 2010 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+#ifndef __ASM_ARCH_MEMORY_H
+#define __ASM_ARCH_MEMORY_H
+
+/* Memory overview:
+
+   [ARMcore] <--virtual addr-->
+   [ARMmmu] <--physical addr-->
+   [GERTmap] <--bus add-->
+   [VCperiph]
+
+*/
+
+/*
+ * Physical DRAM offset.
+ */
+#define PLAT_PHYS_OFFSET	UL(0x00000000)
+#define VC_ARMMEM_OFFSET	UL(0x00000000)   /* offset in VC of ARM memory */
+
+#ifdef CONFIG_BCM2708_NOL2CACHE
+ #define _REAL_BUS_OFFSET UL(0xC0000000)   /* don't use L1 or L2 caches */
+#else
+ #define _REAL_BUS_OFFSET UL(0x40000000)   /* use L2 cache */
+#endif
+
+/* We're using the memory at 64M in the VideoCore for Linux - this adjustment
+ * will provide the offset into this area as well as setting the bits that
+ * stop the L1 and L2 cache from being used
+ *
+ * WARNING: this only works because the ARM is given memory at a fixed location
+ *          (ARMMEM_OFFSET)
+ */
+#define BUS_OFFSET          (VC_ARMMEM_OFFSET + _REAL_BUS_OFFSET)
+#define __virt_to_bus(x)    ((x) + (BUS_OFFSET - PAGE_OFFSET))
+#define __bus_to_virt(x)    ((x) - (BUS_OFFSET - PAGE_OFFSET))
+#define __pfn_to_bus(x)     (__pfn_to_phys(x) + (BUS_OFFSET - PLAT_PHYS_OFFSET))
+#define __bus_to_pfn(x)     __phys_to_pfn((x) - (BUS_OFFSET - PLAT_PHYS_OFFSET))
+
+#endif

arch/arm/mach-bcm2708/include/mach/platform.h

@@ -0,0 +1,228 @@
+/*
+ * arch/arm/mach-bcm2708/include/mach/platform.h
+ *
+ * Copyright (C) 2010 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#ifndef _BCM2708_PLATFORM_H
+#define _BCM2708_PLATFORM_H
+
+
+/* macros to get at IO space when running virtually */
+#define IO_ADDRESS(x)	(((x) & 0x0fffffff) + (((x) >> 4) & 0x0f000000) + 0xf0000000)
+
+#define __io_address(n)     IOMEM(IO_ADDRESS(n))
+
+
+/*
+ *  SDRAM
+ */
+#define BCM2708_SDRAM_BASE           0x00000000
+
+/*
+ *  Logic expansion modules
+ *
+ */
+
+
+/* ------------------------------------------------------------------------
+ *  BCM2708 ARMCTRL Registers
+ * ------------------------------------------------------------------------
+ */
+
+#define HW_REGISTER_RW(addr) (addr)
+#define HW_REGISTER_RO(addr) (addr)
+
+#include "arm_control.h"
+#undef ARM_BASE
+
+/*
+ * Definitions and addresses for the ARM CONTROL logic
+ * This file is manually generated.
+ */
+
+#define BCM2708_PERI_BASE        0x20000000
+#define IC0_BASE                 (BCM2708_PERI_BASE + 0x2000)
+#define ST_BASE                  (BCM2708_PERI_BASE + 0x3000)   /* System Timer */
+#define MPHI_BASE		 (BCM2708_PERI_BASE + 0x6000)	/* Message -based Parallel Host Interface */
+#define DMA_BASE		 (BCM2708_PERI_BASE + 0x7000)	/* DMA controller */
+#define ARM_BASE                 (BCM2708_PERI_BASE + 0xB000)	 /* BCM2708 ARM control block */
+#define PM_BASE			 (BCM2708_PERI_BASE + 0x100000) /* Power Management, Reset controller and Watchdog registers */
+#define PCM_CLOCK_BASE           (BCM2708_PERI_BASE + 0x101098) /* PCM Clock */
+#define RNG_BASE                 (BCM2708_PERI_BASE + 0x104000) /* Hardware RNG */
+#define GPIO_BASE                (BCM2708_PERI_BASE + 0x200000) /* GPIO */
+#define UART0_BASE               (BCM2708_PERI_BASE + 0x201000)	/* Uart 0 */
+#define MMCI0_BASE               (BCM2708_PERI_BASE + 0x202000) /* MMC interface */
+#define I2S_BASE                 (BCM2708_PERI_BASE + 0x203000) /* I2S */
+#define SPI0_BASE		 (BCM2708_PERI_BASE + 0x204000) /* SPI0 */
+#define BSC0_BASE		 (BCM2708_PERI_BASE + 0x205000) /* BSC0 I2C/TWI */
+#define UART1_BASE               (BCM2708_PERI_BASE + 0x215000) /* Uart 1 */
+#define EMMC_BASE                (BCM2708_PERI_BASE + 0x300000) /* eMMC interface */
+#define SMI_BASE		 (BCM2708_PERI_BASE + 0x600000) /* SMI */
+#define BSC1_BASE		 (BCM2708_PERI_BASE + 0x804000) /* BSC1 I2C/TWI */
+#define USB_BASE                 (BCM2708_PERI_BASE + 0x980000) /* DTC_OTG USB controller */
+#define MCORE_BASE               (BCM2708_PERI_BASE + 0x0000)   /* Fake frame buffer device (actually the multicore sync block*/
+
+#define ARMCTRL_BASE             (ARM_BASE + 0x000)
+#define ARMCTRL_IC_BASE          (ARM_BASE + 0x200)           /* ARM interrupt controller */
+#define ARMCTRL_TIMER0_1_BASE    (ARM_BASE + 0x400)           /* Timer 0 and 1 */
+#define ARMCTRL_0_SBM_BASE       (ARM_BASE + 0x800)           /* User 0 (ARM)'s Semaphores Doorbells and Mailboxes */
+
+
+/*
+ * Interrupt assignments
+ */
+
+#define ARM_IRQ1_BASE                  0
+#define INTERRUPT_TIMER0               (ARM_IRQ1_BASE + 0)
+#define INTERRUPT_TIMER1               (ARM_IRQ1_BASE + 1)
+#define INTERRUPT_TIMER2               (ARM_IRQ1_BASE + 2)
+#define INTERRUPT_TIMER3               (ARM_IRQ1_BASE + 3)
+#define INTERRUPT_CODEC0               (ARM_IRQ1_BASE + 4)
+#define INTERRUPT_CODEC1               (ARM_IRQ1_BASE + 5)
+#define INTERRUPT_CODEC2               (ARM_IRQ1_BASE + 6)
+#define INTERRUPT_VC_JPEG              (ARM_IRQ1_BASE + 7)
+#define INTERRUPT_ISP                  (ARM_IRQ1_BASE + 8)
+#define INTERRUPT_VC_USB               (ARM_IRQ1_BASE + 9)
+#define INTERRUPT_VC_3D                (ARM_IRQ1_BASE + 10)
+#define INTERRUPT_TRANSPOSER           (ARM_IRQ1_BASE + 11)
+#define INTERRUPT_MULTICORESYNC0       (ARM_IRQ1_BASE + 12)
+#define INTERRUPT_MULTICORESYNC1       (ARM_IRQ1_BASE + 13)
+#define INTERRUPT_MULTICORESYNC2       (ARM_IRQ1_BASE + 14)
+#define INTERRUPT_MULTICORESYNC3       (ARM_IRQ1_BASE + 15)
+#define INTERRUPT_DMA0                 (ARM_IRQ1_BASE + 16)
+#define INTERRUPT_DMA1                 (ARM_IRQ1_BASE + 17)
+#define INTERRUPT_VC_DMA2              (ARM_IRQ1_BASE + 18)
+#define INTERRUPT_VC_DMA3              (ARM_IRQ1_BASE + 19)
+#define INTERRUPT_DMA4                 (ARM_IRQ1_BASE + 20)
+#define INTERRUPT_DMA5                 (ARM_IRQ1_BASE + 21)
+#define INTERRUPT_DMA6                 (ARM_IRQ1_BASE + 22)
+#define INTERRUPT_DMA7                 (ARM_IRQ1_BASE + 23)
+#define INTERRUPT_DMA8                 (ARM_IRQ1_BASE + 24)
+#define INTERRUPT_DMA9                 (ARM_IRQ1_BASE + 25)
+#define INTERRUPT_DMA10                (ARM_IRQ1_BASE + 26)
+#define INTERRUPT_DMA11                (ARM_IRQ1_BASE + 27)
+#define INTERRUPT_DMA12                (ARM_IRQ1_BASE + 28)
+#define INTERRUPT_AUX                (ARM_IRQ1_BASE + 29)
+#define INTERRUPT_ARM                  (ARM_IRQ1_BASE + 30)
+#define INTERRUPT_VPUDMA               (ARM_IRQ1_BASE + 31)
+
+#define ARM_IRQ2_BASE                  32
+#define INTERRUPT_HOSTPORT             (ARM_IRQ2_BASE + 0)
+#define INTERRUPT_VIDEOSCALER          (ARM_IRQ2_BASE + 1)
+#define INTERRUPT_CCP2TX               (ARM_IRQ2_BASE + 2)
+#define INTERRUPT_SDC                  (ARM_IRQ2_BASE + 3)
+#define INTERRUPT_DSI0                 (ARM_IRQ2_BASE + 4)
+#define INTERRUPT_AVE                  (ARM_IRQ2_BASE + 5)
+#define INTERRUPT_CAM0                 (ARM_IRQ2_BASE + 6)
+#define INTERRUPT_CAM1                 (ARM_IRQ2_BASE + 7)
+#define INTERRUPT_HDMI0                (ARM_IRQ2_BASE + 8)
+#define INTERRUPT_HDMI1                (ARM_IRQ2_BASE + 9)
+#define INTERRUPT_PIXELVALVE1          (ARM_IRQ2_BASE + 10)
+#define INTERRUPT_I2CSPISLV            (ARM_IRQ2_BASE + 11)
+#define INTERRUPT_DSI1                 (ARM_IRQ2_BASE + 12)
+#define INTERRUPT_PWA0                 (ARM_IRQ2_BASE + 13)
+#define INTERRUPT_PWA1                 (ARM_IRQ2_BASE + 14)
+#define INTERRUPT_CPR                  (ARM_IRQ2_BASE + 15)
+#define INTERRUPT_SMI                  (ARM_IRQ2_BASE + 16)
+#define INTERRUPT_GPIO0                (ARM_IRQ2_BASE + 17)
+#define INTERRUPT_GPIO1                (ARM_IRQ2_BASE + 18)
+#define INTERRUPT_GPIO2                (ARM_IRQ2_BASE + 19)
+#define INTERRUPT_GPIO3                (ARM_IRQ2_BASE + 20)
+#define INTERRUPT_VC_I2C               (ARM_IRQ2_BASE + 21)
+#define INTERRUPT_VC_SPI               (ARM_IRQ2_BASE + 22)
+#define INTERRUPT_VC_I2SPCM            (ARM_IRQ2_BASE + 23)
+#define INTERRUPT_VC_SDIO              (ARM_IRQ2_BASE + 24)
+#define INTERRUPT_VC_UART              (ARM_IRQ2_BASE + 25)
+#define INTERRUPT_SLIMBUS              (ARM_IRQ2_BASE + 26)
+#define INTERRUPT_VEC                  (ARM_IRQ2_BASE + 27)
+#define INTERRUPT_CPG                  (ARM_IRQ2_BASE + 28)
+#define INTERRUPT_RNG                  (ARM_IRQ2_BASE + 29)
+#define INTERRUPT_VC_ARASANSDIO        (ARM_IRQ2_BASE + 30)
+#define INTERRUPT_AVSPMON              (ARM_IRQ2_BASE + 31)
+
+#define ARM_IRQ0_BASE                  64
+#define INTERRUPT_ARM_TIMER            (ARM_IRQ0_BASE + 0)
+#define INTERRUPT_ARM_MAILBOX          (ARM_IRQ0_BASE + 1)
+#define INTERRUPT_ARM_DOORBELL_0       (ARM_IRQ0_BASE + 2)
+#define INTERRUPT_ARM_DOORBELL_1       (ARM_IRQ0_BASE + 3)
+#define INTERRUPT_VPU0_HALTED          (ARM_IRQ0_BASE + 4)
+#define INTERRUPT_VPU1_HALTED          (ARM_IRQ0_BASE + 5)
+#define INTERRUPT_ILLEGAL_TYPE0        (ARM_IRQ0_BASE + 6)
+#define INTERRUPT_ILLEGAL_TYPE1        (ARM_IRQ0_BASE + 7)
+#define INTERRUPT_PENDING1             (ARM_IRQ0_BASE + 8)
+#define INTERRUPT_PENDING2             (ARM_IRQ0_BASE + 9)
+#define INTERRUPT_JPEG                 (ARM_IRQ0_BASE + 10)
+#define INTERRUPT_USB                  (ARM_IRQ0_BASE + 11)
+#define INTERRUPT_3D                   (ARM_IRQ0_BASE + 12)
+#define INTERRUPT_DMA2                 (ARM_IRQ0_BASE + 13)
+#define INTERRUPT_DMA3                 (ARM_IRQ0_BASE + 14)
+#define INTERRUPT_I2C                  (ARM_IRQ0_BASE + 15)
+#define INTERRUPT_SPI                  (ARM_IRQ0_BASE + 16)
+#define INTERRUPT_I2SPCM               (ARM_IRQ0_BASE + 17)
+#define INTERRUPT_SDIO                 (ARM_IRQ0_BASE + 18)
+#define INTERRUPT_UART                 (ARM_IRQ0_BASE + 19)
+#define INTERRUPT_ARASANSDIO           (ARM_IRQ0_BASE + 20)
+
+#define MAXIRQNUM                      (32 + 32 + 20)
+#define MAXFIQNUM                      (32 + 32 + 20)
+
+#define MAX_TIMER                       2
+#define MAX_PERIOD                      699050
+#define TICKS_PER_uSEC                  1
+
+/*
+ *  These are useconds NOT ticks.
+ *
+ */
+#define mSEC_1                          1000
+#define mSEC_5                          (mSEC_1 * 5)
+#define mSEC_10                         (mSEC_1 * 10)
+#define mSEC_25                         (mSEC_1 * 25)
+#define SEC_1                           (mSEC_1 * 1000)
+
+/*
+ * Watchdog
+ */
+#define PM_RSTC			       (PM_BASE+0x1c)
+#define PM_RSTS			       (PM_BASE+0x20)
+#define PM_WDOG			       (PM_BASE+0x24)
+
+#define PM_WDOG_RESET                                         0000000000
+#define PM_PASSWORD		       0x5a000000
+#define PM_WDOG_TIME_SET	       0x000fffff
+#define PM_RSTC_WRCFG_CLR              0xffffffcf
+#define PM_RSTC_WRCFG_SET              0x00000030
+#define PM_RSTC_WRCFG_FULL_RESET       0x00000020
+#define PM_RSTC_RESET                  0x00000102
+
+#define PM_RSTS_HADPOR_SET                                 0x00001000
+#define PM_RSTS_HADSRH_SET                                 0x00000400
+#define PM_RSTS_HADSRF_SET                                 0x00000200
+#define PM_RSTS_HADSRQ_SET                                 0x00000100
+#define PM_RSTS_HADWRH_SET                                 0x00000040
+#define PM_RSTS_HADWRF_SET                                 0x00000020
+#define PM_RSTS_HADWRQ_SET                                 0x00000010
+#define PM_RSTS_HADDRH_SET                                 0x00000004
+#define PM_RSTS_HADDRF_SET                                 0x00000002
+#define PM_RSTS_HADDRQ_SET                                 0x00000001
+
+#define UART0_CLOCK      3000000
+
+#endif
+
+/* END */

arch/arm/mach-bcm2708/include/mach/power.h

@@ -0,0 +1,26 @@
+/*
+ *  linux/arch/arm/mach-bcm2708/power.h
+ *
+ *  Copyright (C) 2010 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This device provides a shared mechanism for controlling the power to
+ * VideoCore subsystems.
+ */
+
+#ifndef _MACH_BCM2708_POWER_H
+#define _MACH_BCM2708_POWER_H
+
+#include <linux/types.h>
+#include <mach/arm_power.h>
+
+typedef unsigned int BCM_POWER_HANDLE_T;
+
+extern int bcm_power_open(BCM_POWER_HANDLE_T *handle);
+extern int bcm_power_request(BCM_POWER_HANDLE_T handle, uint32_t request);
+extern int bcm_power_close(BCM_POWER_HANDLE_T handle);
+
+#endif

arch/arm/mach-bcm2708/include/mach/system.h

@@ -0,0 +1,38 @@
+/*
+ *  arch/arm/mach-bcm2708/include/mach/system.h
+ *
+ *  Copyright (C) 2010 Broadcom
+ *  Copyright (C) 2003 ARM Limited
+ *  Copyright (C) 2000 Deep Blue Solutions Ltd
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+#ifndef __ASM_ARCH_SYSTEM_H
+#define __ASM_ARCH_SYSTEM_H
+
+#include <linux/io.h>
+#include <mach/hardware.h>
+#include <mach/platform.h>
+
+static inline void arch_idle(void)
+{
+	/*
+	 * This should do all the clock switching
+	 * and wait for interrupt tricks
+	 */
+	cpu_do_idle();
+}
+
+#endif

arch/arm/mach-bcm2708/include/mach/timex.h

@@ -0,0 +1,23 @@
+/*
+ *  arch/arm/mach-bcm2708/include/mach/timex.h
+ *
+ *  BCM2708 sysem clock frequency
+ *
+ *  Copyright (C) 2010 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#define CLOCK_TICK_RATE		(1000000)

arch/arm/mach-bcm2708/include/mach/uncompress.h

@@ -0,0 +1,84 @@
+/*
+ *  arch/arm/mach-bcn2708/include/mach/uncompress.h
+ *
+ *  Copyright (C) 2010 Broadcom
+ *  Copyright (C) 2003 ARM Limited
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#include <linux/io.h>
+#include <linux/amba/serial.h>
+#include <mach/hardware.h>
+
+#define UART_BAUD 115200
+
+#define BCM2708_UART_DR   __io(UART0_BASE + UART01x_DR)
+#define BCM2708_UART_FR   __io(UART0_BASE + UART01x_FR)
+#define BCM2708_UART_IBRD __io(UART0_BASE + UART011_IBRD)
+#define BCM2708_UART_FBRD __io(UART0_BASE + UART011_FBRD)
+#define BCM2708_UART_LCRH __io(UART0_BASE + UART011_LCRH)
+#define BCM2708_UART_CR   __io(UART0_BASE + UART011_CR)
+
+/*
+ * This does not append a newline
+ */
+static inline void putc(int c)
+{
+	while (__raw_readl(BCM2708_UART_FR) & UART01x_FR_TXFF)
+		barrier();
+
+	__raw_writel(c, BCM2708_UART_DR);
+}
+
+static inline void flush(void)
+{
+	int fr;
+
+	do {
+		fr = __raw_readl(BCM2708_UART_FR);
+		barrier();
+	} while ((fr & (UART011_FR_TXFE | UART01x_FR_BUSY)) != UART011_FR_TXFE);
+}
+
+static inline void arch_decomp_setup(void)
+{
+	int temp, div, rem, frac;
+
+	temp = 16 * UART_BAUD;
+	div = UART0_CLOCK / temp;
+	rem = UART0_CLOCK % temp;
+	temp = (8 * rem) / UART_BAUD;
+	frac = (temp >> 1) + (temp & 1);
+
+	/* Make sure the UART is disabled before we start */
+	__raw_writel(0, BCM2708_UART_CR);
+
+	/* Set the baud rate */
+	__raw_writel(div, BCM2708_UART_IBRD);
+	__raw_writel(frac, BCM2708_UART_FBRD);
+
+	/* Set the UART to 8n1, FIFO enabled */
+	__raw_writel(UART01x_LCRH_WLEN_8 | UART01x_LCRH_FEN, BCM2708_UART_LCRH);
+
+	/* Enable the UART */
+	__raw_writel(UART01x_CR_UARTEN | UART011_CR_TXE | UART011_CR_RXE,
+			BCM2708_UART_CR);
+}
+
+/*
+ * nothing to do
+ */
+#define arch_decomp_wdog()

arch/arm/mach-bcm2708/include/mach/vc_mem.h

@@ -0,0 +1,35 @@
+/*****************************************************************************
+* Copyright 2010 - 2011 Broadcom Corporation.  All rights reserved.
+*
+* Unless you and Broadcom execute a separate written software license
+* agreement governing use of this software, this software is licensed to you
+* under the terms of the GNU General Public License version 2, available at
+* http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
+*
+* Notwithstanding the above, under no circumstances may you combine this
+* software in any way with any other Broadcom software provided under a
+* license other than the GPL, without Broadcom's express prior written
+* consent.
+*****************************************************************************/
+
+#if !defined( VC_MEM_H )
+#define VC_MEM_H
+
+#include <linux/ioctl.h>
+
+#define VC_MEM_IOC_MAGIC  'v'
+
+#define VC_MEM_IOC_MEM_PHYS_ADDR    _IOR( VC_MEM_IOC_MAGIC, 0, unsigned long )
+#define VC_MEM_IOC_MEM_SIZE         _IOR( VC_MEM_IOC_MAGIC, 1, unsigned int )
+#define VC_MEM_IOC_MEM_BASE         _IOR( VC_MEM_IOC_MAGIC, 2, unsigned int )
+#define VC_MEM_IOC_MEM_LOAD         _IOR( VC_MEM_IOC_MAGIC, 3, unsigned int )
+
+#if defined( __KERNEL__ )
+#define VC_MEM_TO_ARM_ADDR_MASK 0x3FFFFFFF
+
+extern unsigned long mm_vc_mem_phys_addr;
+extern unsigned int  mm_vc_mem_size;
+extern int vc_mem_get_current_size( void );
+#endif
+
+#endif  /* VC_MEM_H */

arch/arm/mach-bcm2708/include/mach/vc_sm_defs.h

@@ -0,0 +1,181 @@
+/*****************************************************************************
+* Copyright 2011 Broadcom Corporation.  All rights reserved.
+*
+* Unless you and Broadcom execute a separate written software license
+* agreement governing use of this software, this software is licensed to you
+* under the terms of the GNU General Public License version 2, available at
+* http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
+*
+* Notwithstanding the above, under no circumstances may you combine this
+* software in any way with any other Broadcom software provided under a
+* license other than the GPL, without Broadcom's express prior written
+* consent.
+*****************************************************************************/
+
+#ifndef __VC_SM_DEFS_H__INCLUDED__
+#define __VC_SM_DEFS_H__INCLUDED__
+
+/* FourCC code used for VCHI connection */
+#define VC_SM_SERVER_NAME MAKE_FOURCC("SMEM")
+
+/* Maximum message length */
+#define VC_SM_MAX_MSG_LEN (sizeof(VC_SM_MSG_UNION_T) + \
+	sizeof(VC_SM_MSG_HDR_T))
+#define VC_SM_MAX_RSP_LEN (sizeof(VC_SM_MSG_UNION_T))
+
+/* Resource name maximum size */
+#define VC_SM_RESOURCE_NAME 32
+
+/* All message types supported for HOST->VC direction */
+typedef enum {
+	/* Allocate shared memory block */
+	VC_SM_MSG_TYPE_ALLOC,
+	/* Lock allocated shared memory block */
+	VC_SM_MSG_TYPE_LOCK,
+	/* Unlock allocated shared memory block */
+	VC_SM_MSG_TYPE_UNLOCK,
+	/* Unlock allocated shared memory block, do not answer command */
+	VC_SM_MSG_TYPE_UNLOCK_NOANS,
+	/* Free shared memory block */
+	VC_SM_MSG_TYPE_FREE,
+	/* Resize a shared memory block */
+	VC_SM_MSG_TYPE_RESIZE,
+	/* Walk the allocated shared memory block(s) */
+	VC_SM_MSG_TYPE_WALK_ALLOC,
+
+	/* A previously applied action will need to be reverted */
+	VC_SM_MSG_TYPE_ACTION_CLEAN,
+	VC_SM_MSG_TYPE_MAX
+} VC_SM_MSG_TYPE;
+
+/* Type of memory to be allocated */
+typedef enum {
+	VC_SM_ALLOC_CACHED,
+	VC_SM_ALLOC_NON_CACHED,
+
+} VC_SM_ALLOC_TYPE_T;
+
+/* Message header for all messages in HOST->VC direction */
+typedef struct {
+	int32_t type;
+	uint32_t trans_id;
+	uint8_t body[0];
+
+} VC_SM_MSG_HDR_T;
+
+/* Request to allocate memory (HOST->VC) */
+typedef struct {
+	/* type of memory to allocate */
+	VC_SM_ALLOC_TYPE_T type;
+	/* byte amount of data to allocate per unit */
+	uint32_t base_unit;
+	/* number of unit to allocate */
+	uint32_t num_unit;
+	/* alignement to be applied on allocation */
+	uint32_t alignement;
+	/* identity of who allocated this block */
+	uint32_t allocator;
+	/* resource name (for easier tracking on vc side) */
+	char name[VC_SM_RESOURCE_NAME];
+
+} VC_SM_ALLOC_T;
+
+/* Result of a requested memory allocation (VC->HOST) */
+typedef struct {
+	/* Transaction identifier */
+	uint32_t trans_id;
+
+	/* Resource handle */
+	uint32_t res_handle;
+	/* Pointer to resource buffer */
+	void *res_mem;
+	/* Resource base size (bytes) */
+	uint32_t res_base_size;
+	/* Resource number */
+	uint32_t res_num;
+
+} VC_SM_ALLOC_RESULT_T;
+
+/* Request to free a previously allocated memory (HOST->VC) */
+typedef struct {
+	/* Resource handle (returned from alloc) */
+	uint32_t res_handle;
+	/* Resource buffer (returned from alloc) */
+	void *res_mem;
+
+} VC_SM_FREE_T;
+
+/* Request to lock a previously allocated memory (HOST->VC) */
+typedef struct {
+	/* Resource handle (returned from alloc) */
+	uint32_t res_handle;
+	/* Resource buffer (returned from alloc) */
+	void *res_mem;
+
+} VC_SM_LOCK_UNLOCK_T;
+
+/* Request to resize a previously allocated memory (HOST->VC) */
+typedef struct {
+	/* Resource handle (returned from alloc) */
+	uint32_t res_handle;
+	/* Resource buffer (returned from alloc) */
+	void *res_mem;
+	/* Resource *new* size requested (bytes) */
+	uint32_t res_new_size;
+
+} VC_SM_RESIZE_T;
+
+/* Result of a requested memory lock (VC->HOST) */
+typedef struct {
+	/* Transaction identifier */
+	uint32_t trans_id;
+
+	/* Resource handle */
+	uint32_t res_handle;
+	/* Pointer to resource buffer */
+	void *res_mem;
+	/* Pointer to former resource buffer if the memory
+	 * was reallocated */
+	void *res_old_mem;
+
+} VC_SM_LOCK_RESULT_T;
+
+/* Generic result for a request (VC->HOST) */
+typedef struct {
+	/* Transaction identifier */
+	uint32_t trans_id;
+
+	int32_t success;
+
+} VC_SM_RESULT_T;
+
+/* Request to revert a previously applied action (HOST->VC) */
+typedef struct {
+	/* Action of interest */
+	VC_SM_MSG_TYPE res_action;
+	/* Transaction identifier for the action of interest */
+	uint32_t action_trans_id;
+
+} VC_SM_ACTION_CLEAN_T;
+
+/* Request to remove all data associated with a given allocator (HOST->VC) */
+typedef struct {
+	/* Allocator identifier */
+	uint32_t allocator;
+
+} VC_SM_FREE_ALL_T;
+
+/* Union of ALL messages */
+typedef union {
+	VC_SM_ALLOC_T alloc;
+	VC_SM_ALLOC_RESULT_T alloc_result;
+	VC_SM_FREE_T free;
+	VC_SM_ACTION_CLEAN_T action_clean;
+	VC_SM_RESIZE_T resize;
+	VC_SM_LOCK_RESULT_T lock_result;
+	VC_SM_RESULT_T result;
+	VC_SM_FREE_ALL_T free_all;
+
+} VC_SM_MSG_UNION_T;
+
+#endif /* __VC_SM_DEFS_H__INCLUDED__ */

arch/arm/mach-bcm2708/include/mach/vc_sm_knl.h

@@ -0,0 +1,55 @@
+/*****************************************************************************
+* Copyright 2011 Broadcom Corporation.  All rights reserved.
+*
+* Unless you and Broadcom execute a separate written software license
+* agreement governing use of this software, this software is licensed to you
+* under the terms of the GNU General Public License version 2, available at
+* http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
+*
+* Notwithstanding the above, under no circumstances may you combine this
+* software in any way with any other Broadcom software provided under a
+* license other than the GPL, without Broadcom's express prior written
+* consent.
+*****************************************************************************/
+
+#ifndef __VC_SM_KNL_H__INCLUDED__
+#define __VC_SM_KNL_H__INCLUDED__
+
+#if !defined(__KERNEL__)
+#error "This interface is for kernel use only..."
+#endif
+
+/* Type of memory to be locked (ie mapped) */
+typedef enum {
+	VC_SM_LOCK_CACHED,
+	VC_SM_LOCK_NON_CACHED,
+
+} VC_SM_LOCK_CACHE_MODE_T;
+
+/* Allocate a shared memory handle and block.
+*/
+int vc_sm_alloc(VC_SM_ALLOC_T *alloc, int *handle);
+
+/* Free a previously allocated shared memory handle and block.
+*/
+int vc_sm_free(int handle);
+
+/* Lock a memory handle for use by kernel.
+*/
+int vc_sm_lock(int handle, VC_SM_LOCK_CACHE_MODE_T mode,
+	       long unsigned int *data);
+
+/* Unlock a memory handle in use by kernel.
+*/
+int vc_sm_unlock(int handle, int flush, int no_vc_unlock);
+
+/* Get an internal resource handle mapped from the external one.
+*/
+int vc_sm_int_handle(int handle);
+
+/* Map a shared memory region for use by kernel.
+*/
+int vc_sm_map(int handle, unsigned int sm_addr, VC_SM_LOCK_CACHE_MODE_T mode,
+	      long unsigned int *data);
+
+#endif /* __VC_SM_KNL_H__INCLUDED__ */

arch/arm/mach-bcm2708/include/mach/vc_vchi_sm.h

@@ -0,0 +1,82 @@
+/*****************************************************************************
+* Copyright 2011 Broadcom Corporation.  All rights reserved.
+*
+* Unless you and Broadcom execute a separate written software license
+* agreement governing use of this software, this software is licensed to you
+* under the terms of the GNU General Public License version 2, available at
+* http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
+*
+* Notwithstanding the above, under no circumstances may you combine this
+* software in any way with any other Broadcom software provided under a
+* license other than the GPL, without Broadcom's express prior written
+* consent.
+*****************************************************************************/
+
+#ifndef __VC_VCHI_SM_H__INCLUDED__
+#define __VC_VCHI_SM_H__INCLUDED__
+
+#include "interface/vchi/vchi.h"
+
+#include "vc_sm_defs.h"
+
+/* Forward declare.
+*/
+typedef struct sm_instance *VC_VCHI_SM_HANDLE_T;
+
+/* Initialize the shared memory service, opens up vchi connection to talk to it.
+*/
+VC_VCHI_SM_HANDLE_T vc_vchi_sm_init(VCHI_INSTANCE_T vchi_instance,
+				    VCHI_CONNECTION_T **vchi_connections,
+				    uint32_t num_connections);
+
+/* Terminates the shared memory service.
+*/
+int vc_vchi_sm_stop(VC_VCHI_SM_HANDLE_T *handle);
+
+/* Ask the shared memory service to allocate some memory on videocre and
+** return the result of this allocation (which upon success will be a pointer
+** to some memory in videocore space).
+*/
+int vc_vchi_sm_alloc(VC_VCHI_SM_HANDLE_T handle,
+		     VC_SM_ALLOC_T *alloc,
+		     VC_SM_ALLOC_RESULT_T *alloc_result, uint32_t *trans_id);
+
+/* Ask the shared memory service to free up some memory that was previously
+** allocated by the vc_vchi_sm_alloc function call.
+*/
+int vc_vchi_sm_free(VC_VCHI_SM_HANDLE_T handle,
+		    VC_SM_FREE_T *free, uint32_t *trans_id);
+
+/* Ask the shared memory service to lock up some memory that was previously
+** allocated by the vc_vchi_sm_alloc function call.
+*/
+int vc_vchi_sm_lock(VC_VCHI_SM_HANDLE_T handle,
+		    VC_SM_LOCK_UNLOCK_T *lock_unlock,
+		    VC_SM_LOCK_RESULT_T *lock_result, uint32_t *trans_id);
+
+/* Ask the shared memory service to unlock some memory that was previously
+** allocated by the vc_vchi_sm_alloc function call.
+*/
+int vc_vchi_sm_unlock(VC_VCHI_SM_HANDLE_T handle,
+		      VC_SM_LOCK_UNLOCK_T *lock_unlock,
+		      uint32_t *trans_id, uint8_t wait_reply);
+
+/* Ask the shared memory service to resize some memory that was previously
+** allocated by the vc_vchi_sm_alloc function call.
+*/
+int vc_vchi_sm_resize(VC_VCHI_SM_HANDLE_T handle,
+		      VC_SM_RESIZE_T *resize, uint32_t *trans_id);
+
+/* Walk the allocated resources on the videocore side, the allocation will
+** show up in the log.  This is purely for debug/information and takes no
+** specific actions.
+*/
+int vc_vchi_sm_walk_alloc(VC_VCHI_SM_HANDLE_T handle);
+
+/* Clean up following a previously interrupted action which left the system
+** in a bad state of some sort.
+*/
+int vc_vchi_sm_clean_up(VC_VCHI_SM_HANDLE_T handle,
+			VC_SM_ACTION_CLEAN_T *action_clean);
+
+#endif /* __VC_VCHI_SM_H__INCLUDED__ */

arch/arm/mach-bcm2708/include/mach/vcio.h

@@ -0,0 +1,165 @@
+/*
+ *  arch/arm/mach-bcm2708/include/mach/vcio.h
+ *
+ *  Copyright (C) 2010 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+#ifndef _MACH_BCM2708_VCIO_H
+#define _MACH_BCM2708_VCIO_H
+
+/* Routines to handle I/O via the VideoCore "ARM control" registers
+ * (semaphores, doorbells, mailboxes)
+ */
+
+#define BCM_VCIO_DRIVER_NAME "bcm2708_vcio"
+
+/* Constants shared with the ARM identifying separate mailbox channels */
+#define MBOX_CHAN_POWER    0 /* for use by the power management interface */
+#define MBOX_CHAN_FB       1 /* for use by the frame buffer */
+#define MBOX_CHAN_VCHIQ    3 /* for use by the VCHIQ interface */
+#define MBOX_CHAN_PROPERTY 8 /* for use by the property channel */
+#define MBOX_CHAN_COUNT    9
+
+enum {
+	VCMSG_PROCESS_REQUEST 		= 0x00000000
+};
+enum {
+	VCMSG_REQUEST_SUCCESSFUL 	= 0x80000000,
+	VCMSG_REQUEST_FAILED 		= 0x80000001
+};
+/* Mailbox property tags */
+enum {
+	VCMSG_PROPERTY_END               = 0x00000000,
+	VCMSG_GET_FIRMWARE_REVISION      = 0x00000001,
+	VCMSG_GET_BOARD_MODEL            = 0x00010001,
+	VCMSG_GET_BOARD_REVISION	 = 0x00010002,
+	VCMSG_GET_BOARD_MAC_ADDRESS	 = 0x00010003,
+	VCMSG_GET_BOARD_SERIAL		 = 0x00010004,
+	VCMSG_GET_ARM_MEMORY		 = 0x00010005,
+	VCMSG_GET_VC_MEMORY		 = 0x00010006,
+	VCMSG_GET_CLOCKS		 = 0x00010007,
+	VCMSG_GET_COMMAND_LINE           = 0x00050001,
+	VCMSG_GET_DMA_CHANNELS           = 0x00060001,
+	VCMSG_GET_POWER_STATE            = 0x00020001,
+	VCMSG_GET_TIMING		 = 0x00020002,
+	VCMSG_SET_POWER_STATE            = 0x00028001,
+	VCMSG_GET_CLOCK_STATE            = 0x00030001,
+	VCMSG_SET_CLOCK_STATE            = 0x00038001,
+	VCMSG_GET_CLOCK_RATE             = 0x00030002,
+	VCMSG_SET_CLOCK_RATE             = 0x00038002,
+	VCMSG_GET_VOLTAGE                = 0x00030003,
+	VCMSG_SET_VOLTAGE                = 0x00038003,
+	VCMSG_GET_MAX_CLOCK              = 0x00030004,
+	VCMSG_GET_MAX_VOLTAGE            = 0x00030005,
+	VCMSG_GET_TEMPERATURE            = 0x00030006,
+	VCMSG_GET_MIN_CLOCK              = 0x00030007,
+	VCMSG_GET_MIN_VOLTAGE            = 0x00030008,
+	VCMSG_GET_TURBO                  = 0x00030009,
+	VCMSG_GET_MAX_TEMPERATURE        = 0x0003000a,
+	VCMSG_GET_STC                    = 0x0003000b,
+	VCMSG_SET_TURBO                  = 0x00038009,
+	VCMSG_SET_ALLOCATE_MEM           = 0x0003000c,
+	VCMSG_SET_LOCK_MEM               = 0x0003000d,
+	VCMSG_SET_UNLOCK_MEM             = 0x0003000e,
+	VCMSG_SET_RELEASE_MEM            = 0x0003000f,
+	VCMSG_SET_EXECUTE_CODE           = 0x00030010,
+	VCMSG_SET_EXECUTE_QPU            = 0x00030011,
+	VCMSG_SET_ENABLE_QPU             = 0x00030012,
+	VCMSG_GET_RESOURCE_HANDLE        = 0x00030014,
+	VCMSG_GET_EDID_BLOCK             = 0x00030020,
+	VCMSG_GET_CUSTOMER_OTP           = 0x00030021,
+	VCMSG_SET_CUSTOMER_OTP           = 0x00038021,
+	VCMSG_SET_ALLOCATE_BUFFER        = 0x00040001,
+	VCMSG_SET_RELEASE_BUFFER         = 0x00048001,
+	VCMSG_SET_BLANK_SCREEN           = 0x00040002,
+	VCMSG_TST_BLANK_SCREEN           = 0x00044002,
+	VCMSG_GET_PHYSICAL_WIDTH_HEIGHT  = 0x00040003,
+	VCMSG_TST_PHYSICAL_WIDTH_HEIGHT  = 0x00044003,
+	VCMSG_SET_PHYSICAL_WIDTH_HEIGHT  = 0x00048003,
+	VCMSG_GET_VIRTUAL_WIDTH_HEIGHT   = 0x00040004,
+	VCMSG_TST_VIRTUAL_WIDTH_HEIGHT   = 0x00044004,
+	VCMSG_SET_VIRTUAL_WIDTH_HEIGHT   = 0x00048004,
+	VCMSG_GET_DEPTH                  = 0x00040005,
+	VCMSG_TST_DEPTH                  = 0x00044005,
+	VCMSG_SET_DEPTH                  = 0x00048005,
+	VCMSG_GET_PIXEL_ORDER            = 0x00040006,
+	VCMSG_TST_PIXEL_ORDER            = 0x00044006,
+	VCMSG_SET_PIXEL_ORDER            = 0x00048006,
+	VCMSG_GET_ALPHA_MODE             = 0x00040007,
+	VCMSG_TST_ALPHA_MODE             = 0x00044007,
+	VCMSG_SET_ALPHA_MODE             = 0x00048007,
+	VCMSG_GET_PITCH                  = 0x00040008,
+	VCMSG_TST_PITCH                  = 0x00044008,
+	VCMSG_SET_PITCH                  = 0x00048008,
+	VCMSG_GET_VIRTUAL_OFFSET         = 0x00040009,
+	VCMSG_TST_VIRTUAL_OFFSET         = 0x00044009,
+	VCMSG_SET_VIRTUAL_OFFSET         = 0x00048009,
+	VCMSG_GET_OVERSCAN               = 0x0004000a,
+	VCMSG_TST_OVERSCAN               = 0x0004400a,
+	VCMSG_SET_OVERSCAN               = 0x0004800a,
+	VCMSG_GET_PALETTE                = 0x0004000b,
+	VCMSG_TST_PALETTE                = 0x0004400b,
+	VCMSG_SET_PALETTE                = 0x0004800b,
+	VCMSG_GET_LAYER                  = 0x0004000c,
+	VCMSG_TST_LAYER                  = 0x0004400c,
+	VCMSG_SET_LAYER                  = 0x0004800c,
+	VCMSG_GET_TRANSFORM              = 0x0004000d,
+	VCMSG_TST_TRANSFORM              = 0x0004400d,
+	VCMSG_SET_TRANSFORM              = 0x0004800d,
+	VCMSG_TST_VSYNC                  = 0x0004400e,
+	VCMSG_SET_VSYNC                  = 0x0004800e,
+	VCMSG_SET_CURSOR_INFO            = 0x00008010,
+	VCMSG_SET_CURSOR_STATE           = 0x00008011,
+};
+
+extern int /*rc*/ bcm_mailbox_read(unsigned chan, uint32_t *data28);
+extern int /*rc*/ bcm_mailbox_write(unsigned chan, uint32_t data28);
+extern int /*rc*/ bcm_mailbox_property(void *data, int size);
+
+#include <linux/ioctl.h>
+
+/*
+ * The major device number. We can't rely on dynamic
+ * registration any more, because ioctls need to know
+ * it.
+ */
+#define MAJOR_NUM 100
+
+/*
+ * Set the message of the device driver
+ */
+#define IOCTL_MBOX_PROPERTY _IOWR(MAJOR_NUM, 0, char *)
+/*
+ * _IOWR means that we're creating an ioctl command
+ * number for passing information from a user process
+ * to the kernel module and from the kernel module to user process
+ *
+ * The first arguments, MAJOR_NUM, is the major device
+ * number we're using.
+ *
+ * The second argument is the number of the command
+ * (there could be several with different meanings).
+ *
+ * The third argument is the type we want to get from
+ * the process to the kernel.
+ */
+
+/*
+ * The name of the device file
+ */
+#define DEVICE_FILE_NAME "vcio"
+
+#endif

arch/arm/mach-bcm2708/include/mach/vmalloc.h

@@ -0,0 +1,20 @@
+/*
+ *  arch/arm/mach-bcm2708/include/mach/vmalloc.h
+ *
+ *  Copyright (C) 2010 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+#define VMALLOC_END		(0xe8000000)

arch/arm/mach-bcm2708/include/mach/vmcs_sm_ioctl.h

@@ -0,0 +1,233 @@
+/*****************************************************************************
+*  Copyright 2011 Broadcom Corporation.  All rights reserved.
+*
+*  Unless you and Broadcom execute a separate written software license
+*  agreement governing use of this software, this software is licensed to you
+*  under the terms of the GNU General Public License version 2, available at
+*  http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
+*
+*  Notwithstanding the above, under no circumstances may you combine this
+*  software in any way with any other Broadcom software provided under a
+*  license other than the GPL, without Broadcom's express prior written
+*  consent.
+*
+*****************************************************************************/
+
+#if !defined(__VMCS_SM_IOCTL_H__INCLUDED__)
+#define __VMCS_SM_IOCTL_H__INCLUDED__
+
+/* ---- Include Files ---------------------------------------------------- */
+
+#if defined(__KERNEL__)
+#include <linux/types.h>	/* Needed for standard types */
+#else
+#include <stdint.h>
+#endif
+
+#include <linux/ioctl.h>
+
+/* ---- Constants and Types ---------------------------------------------- */
+
+#define VMCS_SM_RESOURCE_NAME               32
+#define VMCS_SM_RESOURCE_NAME_DEFAULT       "sm-host-resource"
+
+/* Type define used to create unique IOCTL number */
+#define VMCS_SM_MAGIC_TYPE                  'I'
+
+/* IOCTL commands */
+enum vmcs_sm_cmd_e {
+	VMCS_SM_CMD_ALLOC = 0x5A,	/* Start at 0x5A arbitrarily */
+	VMCS_SM_CMD_ALLOC_SHARE,
+	VMCS_SM_CMD_LOCK,
+	VMCS_SM_CMD_LOCK_CACHE,
+	VMCS_SM_CMD_UNLOCK,
+	VMCS_SM_CMD_RESIZE,
+	VMCS_SM_CMD_UNMAP,
+	VMCS_SM_CMD_FREE,
+	VMCS_SM_CMD_FLUSH,
+	VMCS_SM_CMD_INVALID,
+
+	VMCS_SM_CMD_SIZE_USR_HANDLE,
+	VMCS_SM_CMD_CHK_USR_HANDLE,
+
+	VMCS_SM_CMD_MAPPED_USR_HANDLE,
+	VMCS_SM_CMD_MAPPED_USR_ADDRESS,
+	VMCS_SM_CMD_MAPPED_VC_HDL_FROM_ADDR,
+	VMCS_SM_CMD_MAPPED_VC_HDL_FROM_HDL,
+	VMCS_SM_CMD_MAPPED_VC_ADDR_FROM_HDL,
+
+	VMCS_SM_CMD_VC_WALK_ALLOC,
+	VMCS_SM_CMD_HOST_WALK_MAP,
+	VMCS_SM_CMD_HOST_WALK_PID_ALLOC,
+	VMCS_SM_CMD_HOST_WALK_PID_MAP,
+
+	VMCS_SM_CMD_LAST	/* Do no delete */
+};
+
+/* Cache type supported, conveniently matches the user space definition in
+** user-vcsm.h.
+*/
+enum vmcs_sm_cache_e {
+	VMCS_SM_CACHE_NONE,
+	VMCS_SM_CACHE_HOST,
+	VMCS_SM_CACHE_VC,
+	VMCS_SM_CACHE_BOTH,
+};
+
+/* IOCTL Data structures */
+struct vmcs_sm_ioctl_alloc {
+	/* user -> kernel */
+	unsigned int size;
+	unsigned int num;
+	enum vmcs_sm_cache_e cached;
+	char name[VMCS_SM_RESOURCE_NAME];
+
+	/* kernel -> user */
+	unsigned int handle;
+	/* unsigned int base_addr; */
+};
+
+struct vmcs_sm_ioctl_alloc_share {
+	/* user -> kernel */
+	unsigned int handle;
+	unsigned int size;
+};
+
+struct vmcs_sm_ioctl_free {
+	/* user -> kernel */
+	unsigned int handle;
+	/* unsigned int base_addr; */
+};
+
+struct vmcs_sm_ioctl_lock_unlock {
+	/* user -> kernel */
+	unsigned int handle;
+
+	/* kernel -> user */
+	unsigned int addr;
+};
+
+struct vmcs_sm_ioctl_lock_cache {
+	/* user -> kernel */
+	unsigned int handle;
+	enum vmcs_sm_cache_e cached;
+};
+
+struct vmcs_sm_ioctl_resize {
+	/* user -> kernel */
+	unsigned int handle;
+	unsigned int new_size;
+
+	/* kernel -> user */
+	unsigned int old_size;
+};
+
+struct vmcs_sm_ioctl_map {
+	/* user -> kernel */
+	/* and kernel -> user */
+	unsigned int pid;
+	unsigned int handle;
+	unsigned int addr;
+
+	/* kernel -> user */
+	unsigned int size;
+};
+
+struct vmcs_sm_ioctl_walk {
+	/* user -> kernel */
+	unsigned int pid;
+};
+
+struct vmcs_sm_ioctl_chk {
+	/* user -> kernel */
+	unsigned int handle;
+
+	/* kernel -> user */
+	unsigned int addr;
+	unsigned int size;
+	enum vmcs_sm_cache_e cache;
+};
+
+struct vmcs_sm_ioctl_size {
+	/* user -> kernel */
+	unsigned int handle;
+
+	/* kernel -> user */
+	unsigned int size;
+};
+
+struct vmcs_sm_ioctl_cache {
+	/* user -> kernel */
+	unsigned int handle;
+	unsigned int addr;
+	unsigned int size;
+};
+
+/* IOCTL numbers */
+#define VMCS_SM_IOCTL_MEM_ALLOC\
+	_IOR(VMCS_SM_MAGIC_TYPE, VMCS_SM_CMD_ALLOC,\
+	 struct vmcs_sm_ioctl_alloc)
+#define VMCS_SM_IOCTL_MEM_ALLOC_SHARE\
+	_IOR(VMCS_SM_MAGIC_TYPE, VMCS_SM_CMD_ALLOC_SHARE,\
+	 struct vmcs_sm_ioctl_alloc_share)
+#define VMCS_SM_IOCTL_MEM_LOCK\
+	_IOR(VMCS_SM_MAGIC_TYPE, VMCS_SM_CMD_LOCK,\
+	 struct vmcs_sm_ioctl_lock_unlock)
+#define VMCS_SM_IOCTL_MEM_LOCK_CACHE\
+	_IOR(VMCS_SM_MAGIC_TYPE, VMCS_SM_CMD_LOCK_CACHE,\
+	 struct vmcs_sm_ioctl_lock_cache)
+#define VMCS_SM_IOCTL_MEM_UNLOCK\
+	_IOR(VMCS_SM_MAGIC_TYPE, VMCS_SM_CMD_UNLOCK,\
+	 struct vmcs_sm_ioctl_lock_unlock)
+#define VMCS_SM_IOCTL_MEM_RESIZE\
+	_IOR(VMCS_SM_MAGIC_TYPE, VMCS_SM_CMD_RESIZE,\
+	 struct vmcs_sm_ioctl_resize)
+#define VMCS_SM_IOCTL_MEM_FREE\
+	_IOR(VMCS_SM_MAGIC_TYPE, VMCS_SM_CMD_FREE,\
+	 struct vmcs_sm_ioctl_free)
+#define VMCS_SM_IOCTL_MEM_FLUSH\
+	_IOR(VMCS_SM_MAGIC_TYPE, VMCS_SM_CMD_FLUSH,\
+	 struct vmcs_sm_ioctl_cache)
+#define VMCS_SM_IOCTL_MEM_INVALID\
+	_IOR(VMCS_SM_MAGIC_TYPE, VMCS_SM_CMD_INVALID,\
+	 struct vmcs_sm_ioctl_cache)
+
+#define VMCS_SM_IOCTL_SIZE_USR_HDL\
+	_IOR(VMCS_SM_MAGIC_TYPE, VMCS_SM_CMD_SIZE_USR_HANDLE,\
+	 struct vmcs_sm_ioctl_size)
+#define VMCS_SM_IOCTL_CHK_USR_HDL\
+	_IOR(VMCS_SM_MAGIC_TYPE, VMCS_SM_CMD_CHK_USR_HANDLE,\
+	 struct vmcs_sm_ioctl_chk)
+
+#define VMCS_SM_IOCTL_MAP_USR_HDL\
+	_IOR(VMCS_SM_MAGIC_TYPE, VMCS_SM_CMD_MAPPED_USR_HANDLE,\
+	 struct vmcs_sm_ioctl_map)
+#define VMCS_SM_IOCTL_MAP_USR_ADDRESS\
+	_IOR(VMCS_SM_MAGIC_TYPE, VMCS_SM_CMD_MAPPED_USR_ADDRESS,\
+	 struct vmcs_sm_ioctl_map)
+#define VMCS_SM_IOCTL_MAP_VC_HDL_FR_ADDR\
+	_IOR(VMCS_SM_MAGIC_TYPE, VMCS_SM_CMD_MAPPED_VC_HDL_FROM_ADDR,\
+	 struct vmcs_sm_ioctl_map)
+#define VMCS_SM_IOCTL_MAP_VC_HDL_FR_HDL\
+	_IOR(VMCS_SM_MAGIC_TYPE, VMCS_SM_CMD_MAPPED_VC_HDL_FROM_HDL,\
+	 struct vmcs_sm_ioctl_map)
+#define VMCS_SM_IOCTL_MAP_VC_ADDR_FR_HDL\
+	_IOR(VMCS_SM_MAGIC_TYPE, VMCS_SM_CMD_MAPPED_VC_ADDR_FROM_HDL,\
+	 struct vmcs_sm_ioctl_map)
+
+#define VMCS_SM_IOCTL_VC_WALK_ALLOC\
+	_IO(VMCS_SM_MAGIC_TYPE, VMCS_SM_CMD_VC_WALK_ALLOC)
+#define VMCS_SM_IOCTL_HOST_WALK_MAP\
+	_IO(VMCS_SM_MAGIC_TYPE, VMCS_SM_CMD_HOST_WALK_MAP)
+#define VMCS_SM_IOCTL_HOST_WALK_PID_ALLOC\
+	_IOR(VMCS_SM_MAGIC_TYPE, VMCS_SM_CMD_HOST_WALK_PID_ALLOC,\
+	 struct vmcs_sm_ioctl_walk)
+#define VMCS_SM_IOCTL_HOST_WALK_PID_MAP\
+	_IOR(VMCS_SM_MAGIC_TYPE, VMCS_SM_CMD_HOST_WALK_PID_MAP,\
+	 struct vmcs_sm_ioctl_walk)
+
+/* ---- Variable Externs ------------------------------------------------- */
+
+/* ---- Function Prototypes ---------------------------------------------- */
+
+#endif /* __VMCS_SM_IOCTL_H__INCLUDED__ */

arch/arm/mach-bcm2708/power.c

@@ -0,0 +1,194 @@
+/*
+ *	 linux/arch/arm/mach-bcm2708/power.c
+ *
+ *	 Copyright (C) 2010 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This device provides a shared mechanism for controlling the power to
+ * VideoCore subsystems.
+ */
+
+#include <linux/module.h>
+#include <linux/semaphore.h>
+#include <linux/bug.h>
+#include <mach/power.h>
+#include <mach/vcio.h>
+#include <mach/arm_power.h>
+
+#define DRIVER_NAME "bcm2708_power"
+
+#define BCM_POWER_MAXCLIENTS 4
+#define BCM_POWER_NOCLIENT (1<<31)
+
+/* Some drivers expect there devices to be permanently powered */
+#define BCM_POWER_ALWAYS_ON (BCM_POWER_USB)
+
+#if 1
+#define DPRINTK printk
+#else
+#define DPRINTK if (0) printk
+#endif
+
+struct state_struct {
+	uint32_t global_request;
+	uint32_t client_request[BCM_POWER_MAXCLIENTS];
+	struct semaphore client_mutex;
+	struct semaphore mutex;
+} g_state;
+
+int bcm_power_open(BCM_POWER_HANDLE_T *handle)
+{
+	BCM_POWER_HANDLE_T i;
+	int ret = -EBUSY;
+
+	down(&g_state.client_mutex);
+
+	for (i = 0; i < BCM_POWER_MAXCLIENTS; i++) {
+		if (g_state.client_request[i] == BCM_POWER_NOCLIENT) {
+			g_state.client_request[i] = BCM_POWER_NONE;
+			*handle = i;
+			ret = 0;
+			break;
+		}
+	}
+
+	up(&g_state.client_mutex);
+
+	DPRINTK("bcm_power_open() -> %d\n", *handle);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(bcm_power_open);
+
+int bcm_power_request(BCM_POWER_HANDLE_T handle, uint32_t request)
+{
+	int rc = 0;
+
+	DPRINTK("bcm_power_request(%d, %x)\n", handle, request);
+
+	if ((handle < BCM_POWER_MAXCLIENTS) &&
+	    (g_state.client_request[handle] != BCM_POWER_NOCLIENT)) {
+		if (down_interruptible(&g_state.mutex) != 0) {
+			DPRINTK("bcm_power_request -> interrupted\n");
+			return -EINTR;
+		}
+
+		if (request != g_state.client_request[handle]) {
+			uint32_t others_request = 0;
+			uint32_t global_request;
+			BCM_POWER_HANDLE_T i;
+
+			for (i = 0; i < BCM_POWER_MAXCLIENTS; i++) {
+				if (i != handle)
+					others_request |=
+					    g_state.client_request[i];
+			}
+			others_request &= ~BCM_POWER_NOCLIENT;
+
+			global_request = request | others_request;
+			if (global_request != g_state.global_request) {
+				uint32_t actual;
+
+				/* Send a request to VideoCore */
+				bcm_mailbox_write(MBOX_CHAN_POWER,
+						  global_request << 4);
+
+				/* Wait for a response during power-up */
+				if (global_request & ~g_state.global_request) {
+					rc = bcm_mailbox_read(MBOX_CHAN_POWER,
+							      &actual);
+					DPRINTK
+					    ("bcm_mailbox_read -> %08x, %d\n",
+					     actual, rc);
+					actual >>= 4;
+				} else {
+					rc = 0;
+					actual = global_request;
+				}
+
+				if (rc == 0) {
+					if (actual != global_request) {
+						printk(KERN_ERR
+						     "%s: prev global %x, new global %x, actual %x, request %x, others_request %x\n",
+						     __func__,
+						     g_state.global_request,
+						     global_request, actual, request, others_request);
+						/* A failure */
+						BUG_ON((others_request & actual)
+						       != others_request);
+						request &= actual;
+						rc = -EIO;
+					}
+
+					g_state.global_request = actual;
+					g_state.client_request[handle] =
+					    request;
+				}
+			}
+		}
+		up(&g_state.mutex);
+	} else {
+		rc = -EINVAL;
+	}
+	DPRINTK("bcm_power_request -> %d\n", rc);
+	return rc;
+}
+EXPORT_SYMBOL_GPL(bcm_power_request);
+
+int bcm_power_close(BCM_POWER_HANDLE_T handle)
+{
+	int rc;
+
+	DPRINTK("bcm_power_close(%d)\n", handle);
+
+	rc = bcm_power_request(handle, BCM_POWER_NONE);
+	if (rc == 0)
+		g_state.client_request[handle] = BCM_POWER_NOCLIENT;
+
+	return rc;
+}
+EXPORT_SYMBOL_GPL(bcm_power_close);
+
+static int __init bcm_power_init(void)
+{
+#if defined(BCM_POWER_ALWAYS_ON)
+	BCM_POWER_HANDLE_T always_on_handle;
+#endif
+	int rc = 0;
+	int i;
+
+	printk(KERN_INFO "bcm_power: Broadcom power driver\n");
+	bcm_mailbox_write(MBOX_CHAN_POWER, 0);
+
+	for (i = 0; i < BCM_POWER_MAXCLIENTS; i++)
+		g_state.client_request[i] = BCM_POWER_NOCLIENT;
+
+	sema_init(&g_state.client_mutex, 1);
+	sema_init(&g_state.mutex, 1);
+
+	g_state.global_request = 0;
+
+#if defined(BCM_POWER_ALWAYS_ON)
+	if (BCM_POWER_ALWAYS_ON) {
+		bcm_power_open(&always_on_handle);
+		bcm_power_request(always_on_handle, BCM_POWER_ALWAYS_ON);
+	}
+#endif
+
+	return rc;
+}
+
+static void __exit bcm_power_exit(void)
+{
+	bcm_mailbox_write(MBOX_CHAN_POWER, 0);
+}
+
+arch_initcall(bcm_power_init);	/* Initialize early */
+module_exit(bcm_power_exit);
+
+MODULE_AUTHOR("Phil Elwell");
+MODULE_DESCRIPTION("Interface to BCM2708 power management");
+MODULE_LICENSE("GPL");

arch/arm/mach-bcm2708/vc_mem.c

@@ -0,0 +1,432 @@
+/*****************************************************************************
+* Copyright 2010 - 2011 Broadcom Corporation.  All rights reserved.
+*
+* Unless you and Broadcom execute a separate written software license
+* agreement governing use of this software, this software is licensed to you
+* under the terms of the GNU General Public License version 2, available at
+* http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
+*
+* Notwithstanding the above, under no circumstances may you combine this
+* software in any way with any other Broadcom software provided under a
+* license other than the GPL, without Broadcom's express prior written
+* consent.
+*****************************************************************************/
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/fs.h>
+#include <linux/device.h>
+#include <linux/cdev.h>
+#include <linux/mm.h>
+#include <linux/slab.h>
+#include <linux/debugfs.h>
+#include <asm/uaccess.h>
+#include <linux/dma-mapping.h>
+
+#ifdef CONFIG_ARCH_KONA
+#include <chal/chal_ipc.h>
+#elif CONFIG_ARCH_BCM2708
+#else
+#include <csp/chal_ipc.h>
+#endif
+
+#include "mach/vc_mem.h"
+#include <mach/vcio.h>
+
+#define DRIVER_NAME  "vc-mem"
+
+// Device (/dev) related variables
+static dev_t vc_mem_devnum = 0;
+static struct class *vc_mem_class = NULL;
+static struct cdev vc_mem_cdev;
+static int vc_mem_inited = 0;
+
+#ifdef CONFIG_DEBUG_FS
+static struct dentry *vc_mem_debugfs_entry;
+#endif
+
+/*
+ * Videocore memory addresses and size
+ *
+ * Drivers that wish to know the videocore memory addresses and sizes should
+ * use these variables instead of the MM_IO_BASE and MM_ADDR_IO defines in
+ * headers. This allows the other drivers to not be tied down to a a certain
+ * address/size at compile time.
+ *
+ * In the future, the goal is to have the videocore memory virtual address and
+ * size be calculated at boot time rather than at compile time. The decision of
+ * where the videocore memory resides and its size would be in the hands of the
+ * bootloader (and/or kernel). When that happens, the values of these variables
+ * would be calculated and assigned in the init function.
+ */
+// in the 2835 VC in mapped above ARM, but ARM has full access to VC space
+unsigned long mm_vc_mem_phys_addr = 0x00000000;
+unsigned int mm_vc_mem_size = 0;
+unsigned int mm_vc_mem_base = 0;
+
+EXPORT_SYMBOL(mm_vc_mem_phys_addr);
+EXPORT_SYMBOL(mm_vc_mem_size);
+EXPORT_SYMBOL(mm_vc_mem_base);
+
+static uint phys_addr = 0;
+static uint mem_size = 0;
+static uint mem_base = 0;
+
+
+/****************************************************************************
+*
+*   vc_mem_open
+*
+***************************************************************************/
+
+static int
+vc_mem_open(struct inode *inode, struct file *file)
+{
+	(void) inode;
+	(void) file;
+
+	pr_debug("%s: called file = 0x%p\n", __func__, file);
+
+	return 0;
+}
+
+/****************************************************************************
+*
+*   vc_mem_release
+*
+***************************************************************************/
+
+static int
+vc_mem_release(struct inode *inode, struct file *file)
+{
+	(void) inode;
+	(void) file;
+
+	pr_debug("%s: called file = 0x%p\n", __func__, file);
+
+	return 0;
+}
+
+/****************************************************************************
+*
+*   vc_mem_get_size
+*
+***************************************************************************/
+
+static void
+vc_mem_get_size(void)
+{
+}
+
+/****************************************************************************
+*
+*   vc_mem_get_base
+*
+***************************************************************************/
+
+static void
+vc_mem_get_base(void)
+{
+}
+
+/****************************************************************************
+*
+*   vc_mem_get_current_size
+*
+***************************************************************************/
+
+int
+vc_mem_get_current_size(void)
+{
+	return mm_vc_mem_size;
+}
+
+EXPORT_SYMBOL_GPL(vc_mem_get_current_size);
+
+/****************************************************************************
+*
+*   vc_mem_ioctl
+*
+***************************************************************************/
+
+static long
+vc_mem_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
+{
+	int rc = 0;
+
+	(void) cmd;
+	(void) arg;
+
+	pr_debug("%s: called file = 0x%p\n", __func__, file);
+
+	switch (cmd) {
+	case VC_MEM_IOC_MEM_PHYS_ADDR:
+		{
+			pr_debug("%s: VC_MEM_IOC_MEM_PHYS_ADDR=0x%p\n",
+				__func__, (void *) mm_vc_mem_phys_addr);
+
+			if (copy_to_user((void *) arg, &mm_vc_mem_phys_addr,
+					 sizeof (mm_vc_mem_phys_addr)) != 0) {
+				rc = -EFAULT;
+			}
+			break;
+		}
+	case VC_MEM_IOC_MEM_SIZE:
+		{
+			// Get the videocore memory size first
+			vc_mem_get_size();
+
+			pr_debug("%s: VC_MEM_IOC_MEM_SIZE=%u\n", __func__,
+				mm_vc_mem_size);
+
+			if (copy_to_user((void *) arg, &mm_vc_mem_size,
+					 sizeof (mm_vc_mem_size)) != 0) {
+				rc = -EFAULT;
+			}
+			break;
+		}
+	case VC_MEM_IOC_MEM_BASE:
+		{
+			// Get the videocore memory base
+			vc_mem_get_base();
+
+			pr_debug("%s: VC_MEM_IOC_MEM_BASE=%u\n", __func__,
+				mm_vc_mem_base);
+
+			if (copy_to_user((void *) arg, &mm_vc_mem_base,
+					 sizeof (mm_vc_mem_base)) != 0) {
+				rc = -EFAULT;
+			}
+			break;
+		}
+	case VC_MEM_IOC_MEM_LOAD:
+		{
+			// Get the videocore memory base
+			vc_mem_get_base();
+
+			pr_debug("%s: VC_MEM_IOC_MEM_LOAD=%u\n", __func__,
+				mm_vc_mem_base);
+
+			if (copy_to_user((void *) arg, &mm_vc_mem_base,
+					 sizeof (mm_vc_mem_base)) != 0) {
+				rc = -EFAULT;
+			}
+			break;
+		}
+	default:
+		{
+			return -ENOTTY;
+		}
+	}
+	pr_debug("%s: file = 0x%p returning %d\n", __func__, file, rc);
+
+	return rc;
+}
+
+/****************************************************************************
+*
+*   vc_mem_mmap
+*
+***************************************************************************/
+
+static int
+vc_mem_mmap(struct file *filp, struct vm_area_struct *vma)
+{
+	int rc = 0;
+	unsigned long length = vma->vm_end - vma->vm_start;
+	unsigned long offset = vma->vm_pgoff << PAGE_SHIFT;
+
+	pr_debug("%s: vm_start = 0x%08lx vm_end = 0x%08lx vm_pgoff = 0x%08lx\n",
+		__func__, (long) vma->vm_start, (long) vma->vm_end,
+		(long) vma->vm_pgoff);
+
+	if (offset + length > mm_vc_mem_size) {
+		pr_err("%s: length %ld is too big\n", __func__, length);
+		return -EINVAL;
+	}
+	// Do not cache the memory map
+	vma->vm_page_prot = pgprot_noncached(vma->vm_page_prot);
+
+	rc = remap_pfn_range(vma, vma->vm_start,
+			     (mm_vc_mem_phys_addr >> PAGE_SHIFT) +
+			     vma->vm_pgoff, length, vma->vm_page_prot);
+	if (rc != 0) {
+		pr_err("%s: remap_pfn_range failed (rc=%d)\n", __func__, rc);
+	}
+
+	return rc;
+}
+
+/****************************************************************************
+*
+*   File Operations for the driver.
+*
+***************************************************************************/
+
+static const struct file_operations vc_mem_fops = {
+	.owner = THIS_MODULE,
+	.open = vc_mem_open,
+	.release = vc_mem_release,
+	.unlocked_ioctl = vc_mem_ioctl,
+	.mmap = vc_mem_mmap,
+};
+
+#ifdef CONFIG_DEBUG_FS
+static void vc_mem_debugfs_deinit(void)
+{
+	debugfs_remove_recursive(vc_mem_debugfs_entry);
+	vc_mem_debugfs_entry = NULL;
+}
+
+
+static int vc_mem_debugfs_init(
+	struct device *dev)
+{
+	vc_mem_debugfs_entry = debugfs_create_dir(DRIVER_NAME, NULL);
+	if (!vc_mem_debugfs_entry) {
+		dev_warn(dev, "could not create debugfs entry\n");
+		return -EFAULT;
+	}
+
+	if (!debugfs_create_x32("vc_mem_phys_addr",
+				0444,
+				vc_mem_debugfs_entry,
+				(u32 *)&mm_vc_mem_phys_addr)) {
+		dev_warn(dev, "%s:could not create vc_mem_phys entry\n",
+			__func__);
+		goto fail;
+	}
+
+	if (!debugfs_create_x32("vc_mem_size",
+				0444,
+				vc_mem_debugfs_entry,
+				(u32 *)&mm_vc_mem_size)) {
+		dev_warn(dev, "%s:could not create vc_mem_size entry\n",
+			__func__);
+		goto fail;
+	}
+
+	if (!debugfs_create_x32("vc_mem_base",
+				0444,
+				vc_mem_debugfs_entry,
+				(u32 *)&mm_vc_mem_base)) {
+		dev_warn(dev, "%s:could not create vc_mem_base entry\n",
+			 __func__);
+		goto fail;
+	}
+
+	return 0;
+
+fail:
+	vc_mem_debugfs_deinit();
+	return -EFAULT;
+}
+
+#endif /* CONFIG_DEBUG_FS */
+
+
+/****************************************************************************
+*
+*   vc_mem_init
+*
+***************************************************************************/
+
+static int __init
+vc_mem_init(void)
+{
+	int rc = -EFAULT;
+	struct device *dev;
+
+	pr_debug("%s: called\n", __func__);
+
+	mm_vc_mem_phys_addr = phys_addr;
+	mm_vc_mem_size = mem_size;
+	mm_vc_mem_base = mem_base;
+
+	vc_mem_get_size();
+
+	pr_info("vc-mem: phys_addr:0x%08lx mem_base=0x%08x mem_size:0x%08x(%u MiB)\n",
+		mm_vc_mem_phys_addr, mm_vc_mem_base, mm_vc_mem_size, mm_vc_mem_size / (1024 * 1024));
+
+	if ((rc = alloc_chrdev_region(&vc_mem_devnum, 0, 1, DRIVER_NAME)) < 0) {
+		pr_err("%s: alloc_chrdev_region failed (rc=%d)\n",
+		       __func__, rc);
+		goto out_err;
+	}
+
+	cdev_init(&vc_mem_cdev, &vc_mem_fops);
+	if ((rc = cdev_add(&vc_mem_cdev, vc_mem_devnum, 1)) != 0) {
+		pr_err("%s: cdev_add failed (rc=%d)\n", __func__, rc);
+		goto out_unregister;
+	}
+
+	vc_mem_class = class_create(THIS_MODULE, DRIVER_NAME);
+	if (IS_ERR(vc_mem_class)) {
+		rc = PTR_ERR(vc_mem_class);
+		pr_err("%s: class_create failed (rc=%d)\n", __func__, rc);
+		goto out_cdev_del;
+	}
+
+	dev = device_create(vc_mem_class, NULL, vc_mem_devnum, NULL,
+			    DRIVER_NAME);
+	if (IS_ERR(dev)) {
+		rc = PTR_ERR(dev);
+		pr_err("%s: device_create failed (rc=%d)\n", __func__, rc);
+		goto out_class_destroy;
+	}
+
+#ifdef CONFIG_DEBUG_FS
+	/* don't fail if the debug entries cannot be created */
+	vc_mem_debugfs_init(dev);
+#endif
+
+	vc_mem_inited = 1;
+	return 0;
+
+	device_destroy(vc_mem_class, vc_mem_devnum);
+
+      out_class_destroy:
+	class_destroy(vc_mem_class);
+	vc_mem_class = NULL;
+
+      out_cdev_del:
+	cdev_del(&vc_mem_cdev);
+
+      out_unregister:
+	unregister_chrdev_region(vc_mem_devnum, 1);
+
+      out_err:
+	return -1;
+}
+
+/****************************************************************************
+*
+*   vc_mem_exit
+*
+***************************************************************************/
+
+static void __exit
+vc_mem_exit(void)
+{
+	pr_debug("%s: called\n", __func__);
+
+	if (vc_mem_inited) {
+#if CONFIG_DEBUG_FS
+		vc_mem_debugfs_deinit();
+#endif
+		device_destroy(vc_mem_class, vc_mem_devnum);
+		class_destroy(vc_mem_class);
+		cdev_del(&vc_mem_cdev);
+		unregister_chrdev_region(vc_mem_devnum, 1);
+	}
+}
+
+module_init(vc_mem_init);
+module_exit(vc_mem_exit);
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Broadcom Corporation");
+
+module_param(phys_addr, uint, 0644);
+module_param(mem_size, uint, 0644);
+module_param(mem_base, uint, 0644);
+

arch/arm/mach-bcm2708/vcio.c

@@ -0,0 +1,474 @@
+/*
+ *  linux/arch/arm/mach-bcm2708/vcio.c
+ *
+ *  Copyright (C) 2010 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This device provides a shared mechanism for writing to the mailboxes,
+ * semaphores, doorbells etc. that are shared between the ARM and the
+ * VideoCore processor
+ */
+
+#if defined(CONFIG_SERIAL_BCM_MBOX_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
+#define SUPPORT_SYSRQ
+#endif
+
+#include <linux/module.h>
+#include <linux/console.h>
+#include <linux/serial_core.h>
+#include <linux/serial.h>
+#include <linux/errno.h>
+#include <linux/device.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/dma-mapping.h>
+#include <linux/platform_device.h>
+#include <linux/sysrq.h>
+#include <linux/delay.h>
+#include <linux/slab.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+
+#include <linux/io.h>
+
+#include <mach/vcio.h>
+#include <mach/platform.h>
+
+#include <asm/uaccess.h>
+
+
+#define DRIVER_NAME BCM_VCIO_DRIVER_NAME
+
+/* ----------------------------------------------------------------------
+ *	Mailbox
+ * -------------------------------------------------------------------- */
+
+/* offsets from a mail box base address */
+#define MAIL_WRT	0x00	/* write - and next 4 words */
+#define MAIL_RD		0x00	/* read - and next 4 words */
+#define MAIL_POL	0x10	/* read without popping the fifo */
+#define MAIL_SND	0x14	/* sender ID (bottom two bits) */
+#define MAIL_STA	0x18	/* status */
+#define MAIL_CNF	0x1C	/* configuration */
+
+#define MBOX_MSG(chan, data28)		(((data28) & ~0xf) | ((chan) & 0xf))
+#define MBOX_MSG_LSB(chan, data28) (((data28) << 4) | ((chan) & 0xf))
+#define MBOX_CHAN(msg)			((msg) & 0xf)
+#define MBOX_DATA28(msg)		((msg) & ~0xf)
+#define MBOX_DATA28_LSB(msg)		(((uint32_t)msg) >> 4)
+
+#define MBOX_MAGIC 0xd0d0c0de
+
+struct vc_mailbox {
+	struct device *dev;	/* parent device */
+	void __iomem *status;
+	void __iomem *config;
+	void __iomem *read;
+	void __iomem *write;
+	uint32_t msg[MBOX_CHAN_COUNT];
+	struct semaphore sema[MBOX_CHAN_COUNT];
+	uint32_t magic;
+};
+
+static void mbox_init(struct vc_mailbox *mbox_out, struct device *dev,
+		      uint32_t addr_mbox)
+{
+	int i;
+
+	mbox_out->dev = dev;
+	mbox_out->status = __io_address(addr_mbox + MAIL_STA);
+	mbox_out->config = __io_address(addr_mbox + MAIL_CNF);
+	mbox_out->read = __io_address(addr_mbox + MAIL_RD);
+	/* Write to the other mailbox */
+	mbox_out->write =
+	    __io_address((addr_mbox ^ ARM_0_MAIL0_WRT ^ ARM_0_MAIL1_WRT) +
+			 MAIL_WRT);
+
+	for (i = 0; i < MBOX_CHAN_COUNT; i++) {
+		mbox_out->msg[i] = 0;
+		sema_init(&mbox_out->sema[i], 0);
+	}
+
+	/* Enable the interrupt on data reception */
+	writel(ARM_MC_IHAVEDATAIRQEN, mbox_out->config);
+
+	mbox_out->magic = MBOX_MAGIC;
+}
+
+static int mbox_write(struct vc_mailbox *mbox, unsigned chan, uint32_t data28)
+{
+	int rc;
+
+	if (mbox->magic != MBOX_MAGIC)
+		rc = -EINVAL;
+	else {
+		/* wait for the mailbox FIFO to have some space in it */
+		while (0 != (readl(mbox->status) & ARM_MS_FULL))
+			cpu_relax();
+
+		writel(MBOX_MSG(chan, data28), mbox->write);
+		rc = 0;
+	}
+	return rc;
+}
+
+static int mbox_read(struct vc_mailbox *mbox, unsigned chan, uint32_t *data28)
+{
+	int rc;
+
+	if (mbox->magic != MBOX_MAGIC)
+		rc = -EINVAL;
+	else {
+		down(&mbox->sema[chan]);
+		*data28 = MBOX_DATA28(mbox->msg[chan]);
+		mbox->msg[chan] = 0;
+		rc = 0;
+	}
+	return rc;
+}
+
+static irqreturn_t mbox_irq(int irq, void *dev_id)
+{
+	/* wait for the mailbox FIFO to have some data in it */
+	struct vc_mailbox *mbox = (struct vc_mailbox *) dev_id;
+	int status = readl(mbox->status);
+	int ret = IRQ_NONE;
+
+	while (!(status & ARM_MS_EMPTY)) {
+		uint32_t msg = readl(mbox->read);
+		int chan = MBOX_CHAN(msg);
+		if (chan < MBOX_CHAN_COUNT) {
+			if (mbox->msg[chan]) {
+				/* Overflow */
+				printk(KERN_ERR DRIVER_NAME
+				       ": mbox chan %d overflow - drop %08x\n",
+				       chan, msg);
+			} else {
+				mbox->msg[chan] = (msg | 0xf);
+				up(&mbox->sema[chan]);
+			}
+		} else {
+			printk(KERN_ERR DRIVER_NAME
+			       ": invalid channel selector (msg %08x)\n", msg);
+		}
+		ret = IRQ_HANDLED;
+		status = readl(mbox->status);
+	}
+	return ret;
+}
+
+static struct irqaction mbox_irqaction = {
+	.name = "ARM Mailbox IRQ",
+	.flags = IRQF_DISABLED | IRQF_IRQPOLL,
+	.handler = mbox_irq,
+};
+
+/* ----------------------------------------------------------------------
+ *	Mailbox Methods
+ * -------------------------------------------------------------------- */
+
+static struct device *mbox_dev;	/* we assume there's only one! */
+
+static int dev_mbox_write(struct device *dev, unsigned chan, uint32_t data28)
+{
+	int rc;
+
+	struct vc_mailbox *mailbox = dev_get_drvdata(dev);
+	device_lock(dev);
+	rc = mbox_write(mailbox, chan, data28);
+	device_unlock(dev);
+
+	return rc;
+}
+
+static int dev_mbox_read(struct device *dev, unsigned chan, uint32_t *data28)
+{
+	int rc;
+
+	struct vc_mailbox *mailbox = dev_get_drvdata(dev);
+	device_lock(dev);
+	rc = mbox_read(mailbox, chan, data28);
+	device_unlock(dev);
+
+	return rc;
+}
+
+extern int bcm_mailbox_write(unsigned chan, uint32_t data28)
+{
+	if (mbox_dev)
+		return dev_mbox_write(mbox_dev, chan, data28);
+	else
+		return -ENODEV;
+}
+EXPORT_SYMBOL_GPL(bcm_mailbox_write);
+
+extern int bcm_mailbox_read(unsigned chan, uint32_t *data28)
+{
+	if (mbox_dev)
+		return dev_mbox_read(mbox_dev, chan, data28);
+	else
+		return -ENODEV;
+}
+EXPORT_SYMBOL_GPL(bcm_mailbox_read);
+
+static void dev_mbox_register(const char *dev_name, struct device *dev)
+{
+	mbox_dev = dev;
+}
+
+static int mbox_copy_from_user(void *dst, const void *src, int size)
+{
+	if ( (uint32_t)src < TASK_SIZE)
+	{
+		return copy_from_user(dst, src, size);
+	}
+	else
+	{
+		memcpy( dst, src, size );
+		return 0;
+	}
+}
+
+static int mbox_copy_to_user(void *dst, const void *src, int size)
+{
+	if ( (uint32_t)dst < TASK_SIZE)
+	{
+		return copy_to_user(dst, src, size);
+	}
+	else
+	{
+		memcpy( dst, src, size );
+		return 0;
+	}
+}
+
+static DEFINE_MUTEX(mailbox_lock);
+extern int bcm_mailbox_property(void *data, int size)
+{
+	uint32_t success;
+	dma_addr_t mem_bus;				/* the memory address accessed from videocore */
+	void *mem_kern;					/* the memory address accessed from driver */
+	int s = 0;
+
+        mutex_lock(&mailbox_lock);
+	/* allocate some memory for the messages communicating with GPU */
+	mem_kern = dma_alloc_coherent(NULL, PAGE_ALIGN(size), &mem_bus, GFP_ATOMIC);
+	if (mem_kern) {
+		/* create the message */
+		mbox_copy_from_user(mem_kern, data, size);
+
+		/* send the message */
+		wmb();
+		s = bcm_mailbox_write(MBOX_CHAN_PROPERTY, (uint32_t)mem_bus);
+		if (s == 0) {
+			s = bcm_mailbox_read(MBOX_CHAN_PROPERTY, &success);
+		}
+		if (s == 0) {
+			/* copy the response */
+			rmb();
+			mbox_copy_to_user(data, mem_kern, size);
+		}
+		dma_free_coherent(NULL, PAGE_ALIGN(size), mem_kern, mem_bus);
+	} else {
+		s = -ENOMEM;
+	}
+	if (s != 0)
+		printk(KERN_ERR DRIVER_NAME ": %s failed (%d)\n", __func__, s);
+
+        mutex_unlock(&mailbox_lock);
+	return s;
+}
+EXPORT_SYMBOL_GPL(bcm_mailbox_property);
+
+/* ----------------------------------------------------------------------
+ *	Platform Device for Mailbox
+ * -------------------------------------------------------------------- */
+
+/*
+ * Is the device open right now? Used to prevent
+ * concurent access into the same device
+ */
+static int Device_Open = 0;
+
+/*
+ * This is called whenever a process attempts to open the device file
+ */
+static int device_open(struct inode *inode, struct file *file)
+{
+	/*
+	 * We don't want to talk to two processes at the same time
+	 */
+	if (Device_Open)
+		return -EBUSY;
+
+	Device_Open++;
+	/*
+	 * Initialize the message
+	 */
+	try_module_get(THIS_MODULE);
+	return 0;
+}
+
+static int device_release(struct inode *inode, struct file *file)
+{
+	/*
+	 * We're now ready for our next caller
+	 */
+	Device_Open--;
+
+	module_put(THIS_MODULE);
+	return 0;
+}
+
+/*
+ * This function is called whenever a process tries to do an ioctl on our
+ * device file. We get two extra parameters (additional to the inode and file
+ * structures, which all device functions get): the number of the ioctl called
+ * and the parameter given to the ioctl function.
+ *
+ * If the ioctl is write or read/write (meaning output is returned to the
+ * calling process), the ioctl call returns the output of this function.
+ *
+ */
+static long device_ioctl(struct file *file,	/* see include/linux/fs.h */
+		 unsigned int ioctl_num,	/* number and param for ioctl */
+		 unsigned long ioctl_param)
+{
+	unsigned size;
+	/*
+	 * Switch according to the ioctl called
+	 */
+	switch (ioctl_num) {
+	case IOCTL_MBOX_PROPERTY:
+		/*
+		 * Receive a pointer to a message (in user space) and set that
+		 * to be the device's message.  Get the parameter given to
+		 * ioctl by the process.
+		 */
+		mbox_copy_from_user(&size, (void *)ioctl_param, sizeof size);
+		return bcm_mailbox_property((void *)ioctl_param, size);
+		break;
+	default:
+		printk(KERN_ERR DRIVER_NAME "unknown ioctl: %d\n", ioctl_num);
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+/* Module Declarations */
+
+/*
+ * This structure will hold the functions to be called
+ * when a process does something to the device we
+ * created. Since a pointer to this structure is kept in
+ * the devices table, it can't be local to
+ * init_module. NULL is for unimplemented functios.
+ */
+struct file_operations fops = {
+	.unlocked_ioctl = device_ioctl,
+	.open = device_open,
+	.release = device_release,	/* a.k.a. close */
+};
+
+static int bcm_vcio_probe(struct platform_device *pdev)
+{
+	int ret = 0;
+	struct vc_mailbox *mailbox;
+
+	mailbox = kzalloc(sizeof(*mailbox), GFP_KERNEL);
+	if (NULL == mailbox) {
+		printk(KERN_ERR DRIVER_NAME ": failed to allocate "
+		       "mailbox memory\n");
+		ret = -ENOMEM;
+	} else {
+		struct resource *res;
+
+		res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+		if (res == NULL) {
+			printk(KERN_ERR DRIVER_NAME ": failed to obtain memory "
+			       "resource\n");
+			ret = -ENODEV;
+			kfree(mailbox);
+		} else {
+			/* should be based on the registers from res really */
+			mbox_init(mailbox, &pdev->dev, ARM_0_MAIL0_RD);
+
+			platform_set_drvdata(pdev, mailbox);
+			dev_mbox_register(DRIVER_NAME, &pdev->dev);
+
+			mbox_irqaction.dev_id = mailbox;
+			setup_irq(IRQ_ARM_MAILBOX, &mbox_irqaction);
+			printk(KERN_INFO DRIVER_NAME ": mailbox at %p\n",
+			       __io_address(ARM_0_MAIL0_RD));
+		}
+	}
+
+	if (ret == 0) {
+		/*
+		 * Register the character device
+		 */
+		ret = register_chrdev(MAJOR_NUM, DEVICE_FILE_NAME, &fops);
+
+		/*
+		 * Negative values signify an error
+		 */
+		if (ret < 0) {
+			printk(KERN_ERR DRIVER_NAME
+			       "Failed registering the character device %d\n", ret);
+			return ret;
+		}
+	}
+	return ret;
+}
+
+static int bcm_vcio_remove(struct platform_device *pdev)
+{
+	struct vc_mailbox *mailbox = platform_get_drvdata(pdev);
+
+	platform_set_drvdata(pdev, NULL);
+	kfree(mailbox);
+
+	return 0;
+}
+
+static struct platform_driver bcm_mbox_driver = {
+	.probe = bcm_vcio_probe,
+	.remove = bcm_vcio_remove,
+
+	.driver = {
+		   .name = DRIVER_NAME,
+		   .owner = THIS_MODULE,
+		   },
+};
+
+static int __init bcm_mbox_init(void)
+{
+	int ret;
+
+	printk(KERN_INFO "mailbox: Broadcom VideoCore Mailbox driver\n");
+
+	ret = platform_driver_register(&bcm_mbox_driver);
+	if (ret != 0) {
+		printk(KERN_ERR DRIVER_NAME ": failed to register "
+		       "on platform\n");
+	}
+
+	return ret;
+}
+
+static void __exit bcm_mbox_exit(void)
+{
+	platform_driver_unregister(&bcm_mbox_driver);
+}
+
+arch_initcall(bcm_mbox_init);	/* Initialize early */
+module_exit(bcm_mbox_exit);
+
+MODULE_AUTHOR("Gray Girling");
+MODULE_DESCRIPTION("ARM I/O to VideoCore processor");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:bcm-mbox");

arch/arm/mach-exynos/mcpm-exynos.c

@@ -39,7 +39,6 @@
 	"mcr	p15, 0, r0, c1, c0, 0	@ set SCTLR\n\t" \
 	"isb\n\t"\
 	"bl	v7_flush_dcache_"__stringify(level)"\n\t" \
-	"clrex\n\t"\
 	"mrc	p15, 0, r0, c1, c0, 1	@ get ACTLR\n\t" \
 	"bic	r0, r0, #(1 << 6)	@ disable local coherency\n\t" \
 	/* Dummy Load of a device register to avoid Erratum 799270 */ \

arch/arm/mach-imx/clk-gate2.c

@@ -97,7 +97,7 @@ static int clk_gate2_is_enabled(struct clk_hw *hw)
 	struct clk_gate2 *gate = to_clk_gate2(hw);
 
 	if (gate->share_count)
-		return !!(*gate->share_count);
+		return !!__clk_get_enable_count(hw->clk);
 	else
 		return clk_gate2_reg_is_enabled(gate->reg, gate->bit_idx);
 }
@@ -127,10 +127,6 @@ struct clk *clk_register_gate2(struct device *dev, const char *name,
 	gate->bit_idx = bit_idx;
 	gate->flags = clk_gate2_flags;
 	gate->lock = lock;
-
-	/* Initialize share_count per hardware state */
-	if (share_count)
-		*share_count = clk_gate2_reg_is_enabled(reg, bit_idx) ? 1 : 0;
 	gate->share_count = share_count;
 
 	init.name = name;

arch/arm/mach-imx/suspend-imx6.S

@@ -172,6 +172,8 @@ ENTRY(imx6_suspend)
 	ldr	r6, [r11, #0x0]
 	ldr	r11, [r0, #PM_INFO_MX6Q_GPC_V_OFFSET]
 	ldr	r6, [r11, #0x0]
+	ldr	r11, [r0, #PM_INFO_MX6Q_IOMUXC_V_OFFSET]
+	ldr	r6, [r11, #0x0]
 
 	/* use r11 to store the IO address */
 	ldr	r11, [r0, #PM_INFO_MX6Q_SRC_V_OFFSET]

arch/arm/mach-omap2/control.c

@@ -314,7 +314,8 @@ void omap3_save_scratchpad_contents(void)
 		scratchpad_contents.public_restore_ptr =
 			virt_to_phys(omap3_restore_3630);
 	else if (omap_rev() != OMAP3430_REV_ES3_0 &&
-					omap_rev() != OMAP3430_REV_ES3_1)
+					omap_rev() != OMAP3430_REV_ES3_1 &&
+					omap_rev() != OMAP3430_REV_ES3_1_2)
 		scratchpad_contents.public_restore_ptr =
 			virt_to_phys(omap3_restore);
 	else

arch/arm/mach-omap2/omap_hwmod.c

@@ -2185,6 +2185,8 @@ static int _enable(struct omap_hwmod *oh)
 			 oh->mux->pads_dynamic))) {
 		omap_hwmod_mux(oh->mux, _HWMOD_STATE_ENABLED);
 		_reconfigure_io_chain();
+	} else if (oh->flags & HWMOD_FORCE_MSTANDBY) {
+		_reconfigure_io_chain();
 	}
 
 	_add_initiator_dep(oh, mpu_oh);
@@ -2291,6 +2293,8 @@ static int _idle(struct omap_hwmod *oh)
 	if (oh->mux && oh->mux->pads_dynamic) {
 		omap_hwmod_mux(oh->mux, _HWMOD_STATE_IDLE);
 		_reconfigure_io_chain();
+	} else if (oh->flags & HWMOD_FORCE_MSTANDBY) {
+		_reconfigure_io_chain();
 	}
 
 	oh->_state = _HWMOD_STATE_IDLE;
@@ -3345,6 +3349,9 @@ int __init omap_hwmod_register_links(struct omap_hwmod_ocp_if **ois)
 	if (!ois)
 		return 0;
 
+	if (ois[0] == NULL) /* Empty list */
+		return 0;
+
 	if (!linkspace) {
 		if (_alloc_linkspace(ois)) {
 			pr_err("omap_hwmod: could not allocate link space\n");

arch/arm/mach-omap2/omap_hwmod_7xx_data.c

@@ -35,6 +35,7 @@
 #include "i2c.h"
 #include "mmc.h"
 #include "wd_timer.h"
+#include "soc.h"
 
 /* Base offset for all DRA7XX interrupts external to MPUSS */
 #define DRA7XX_IRQ_GIC_START	32
@@ -2705,7 +2706,6 @@ static struct omap_hwmod_ocp_if *dra7xx_hwmod_ocp_ifs[] __initdata = {
 	&dra7xx_l4_per3__usb_otg_ss1,
 	&dra7xx_l4_per3__usb_otg_ss2,
 	&dra7xx_l4_per3__usb_otg_ss3,
-	&dra7xx_l4_per3__usb_otg_ss4,
 	&dra7xx_l3_main_1__vcp1,
 	&dra7xx_l4_per2__vcp1,
 	&dra7xx_l3_main_1__vcp2,
@@ -2714,8 +2714,26 @@ static struct omap_hwmod_ocp_if *dra7xx_hwmod_ocp_ifs[] __initdata = {
 	NULL,
 };
 
+static struct omap_hwmod_ocp_if *dra74x_hwmod_ocp_ifs[] __initdata = {
+	&dra7xx_l4_per3__usb_otg_ss4,
+	NULL,
+};
+
+static struct omap_hwmod_ocp_if *dra72x_hwmod_ocp_ifs[] __initdata = {
+	NULL,
+};
+
 int __init dra7xx_hwmod_init(void)
 {
+	int ret;
+
 	omap_hwmod_init();
-	return omap_hwmod_register_links(dra7xx_hwmod_ocp_ifs);
+	ret = omap_hwmod_register_links(dra7xx_hwmod_ocp_ifs);
+
+	if (!ret && soc_is_dra74x())
+		return omap_hwmod_register_links(dra74x_hwmod_ocp_ifs);
+	else if (!ret && soc_is_dra72x())
+		return omap_hwmod_register_links(dra72x_hwmod_ocp_ifs);
+
+	return ret;
 }

arch/arm/mach-omap2/soc.h

@@ -245,6 +245,8 @@ IS_AM_SUBCLASS(437x, 0x437)
 #define soc_is_omap54xx()		0
 #define soc_is_omap543x()		0
 #define soc_is_dra7xx()			0
+#define soc_is_dra74x()			0
+#define soc_is_dra72x()			0
 
 #if defined(MULTI_OMAP2)
 # if defined(CONFIG_ARCH_OMAP2)
@@ -393,7 +395,11 @@ IS_OMAP_TYPE(3430, 0x3430)
 
 #if defined(CONFIG_SOC_DRA7XX)
 #undef soc_is_dra7xx
+#undef soc_is_dra74x
+#undef soc_is_dra72x
 #define soc_is_dra7xx()	(of_machine_is_compatible("ti,dra7"))
+#define soc_is_dra74x()	(of_machine_is_compatible("ti,dra74"))
+#define soc_is_dra72x()	(of_machine_is_compatible("ti,dra72"))
 #endif
 
 /* Various silicon revisions for omap2 */

arch/arm/mm/Kconfig

@@ -358,7 +358,7 @@ config CPU_PJ4B
 
 # ARMv6
 config CPU_V6
-	bool "Support ARM V6 processor" if ARCH_INTEGRATOR || MACH_REALVIEW_EB || MACH_REALVIEW_PBX
+	bool "Support ARM V6 processor" if ARCH_INTEGRATOR || MACH_REALVIEW_EB || MACH_REALVIEW_PBX || MACH_BCM2708
 	select CPU_32v6
 	select CPU_ABRT_EV6
 	select CPU_CACHE_V6

arch/arm/mm/abort-ev6.S

@@ -17,12 +17,6 @@
  */
 	.align	5
 ENTRY(v6_early_abort)
-#ifdef CONFIG_CPU_V6
-	sub	r1, sp, #4			@ Get unused stack location
-	strex	r0, r1, [r1]			@ Clear the exclusive monitor
-#elif defined(CONFIG_CPU_32v6K)
-	clrex
-#endif
 	mrc	p15, 0, r1, c5, c0, 0		@ get FSR
 	mrc	p15, 0, r0, c6, c0, 0		@ get FAR
 /*

arch/arm/mm/abort-ev7.S

@@ -13,12 +13,6 @@
  */
 	.align	5
 ENTRY(v7_early_abort)
-	/*
-	 * The effect of data aborts on on the exclusive access monitor are
-	 * UNPREDICTABLE. Do a CLREX to clear the state
-	 */
-	clrex
-
 	mrc	p15, 0, r1, c5, c0, 0		@ get FSR
 	mrc	p15, 0, r0, c6, c0, 0		@ get FAR
 

arch/arm/mm/alignment.c

@@ -41,6 +41,7 @@
  * This code is not portable to processors with late data abort handling.
  */
 #define CODING_BITS(i)	(i & 0x0e000000)
+#define COND_BITS(i)	(i & 0xf0000000)
 
 #define LDST_I_BIT(i)	(i & (1 << 26))		/* Immediate constant	*/
 #define LDST_P_BIT(i)	(i & (1 << 24))		/* Preindex		*/
@@ -819,6 +820,8 @@ do_alignment(unsigned long addr, unsigned int fsr, struct pt_regs *regs)
 		break;
 
 	case 0x04000000:	/* ldr or str immediate */
+		if (COND_BITS(instr) == 0xf0000000) /* NEON VLDn, VSTn */
+			goto bad;
 		offset.un = OFFSET_BITS(instr);
 		handler = do_alignment_ldrstr;
 		break;

arch/arm/mm/proc-v6.S

@@ -73,10 +73,19 @@ ENDPROC(cpu_v6_reset)
  *
  *	IRQs are already disabled.
  */
+
+/* See jira SW-5991 for details of this workaround */
 ENTRY(cpu_v6_do_idle)
-	mov	r1, #0
-	mcr	p15, 0, r1, c7, c10, 4		@ DWB - WFI may enter a low-power mode
-	mcr	p15, 0, r1, c7, c0, 4		@ wait for interrupt
+	.align 5
+	mov     r1, #2
+1:	subs	r1, #1
+	nop
+	mcreq	p15, 0, r1, c7, c10, 4		@ DWB - WFI may enter a low-power mode
+	mcreq	p15, 0, r1, c7, c0, 4		@ wait for interrupt
+	nop
+	nop
+	nop
+	bne 1b
 	mov	pc, lr
 
 ENTRY(cpu_v6_dcache_clean_area)

arch/arm/tools/mach-types

@@ -522,6 +522,7 @@ torbreck		MACH_TORBRECK		TORBRECK		3090
 prima2_evb		MACH_PRIMA2_EVB		PRIMA2_EVB		3103
 paz00			MACH_PAZ00		PAZ00			3128
 acmenetusfoxg20		MACH_ACMENETUSFOXG20	ACMENETUSFOXG20		3129
+bcm2708			MACH_BCM2708		BCM2708			3138
 ag5evm			MACH_AG5EVM		AG5EVM			3189
 ics_if_voip		MACH_ICS_IF_VOIP	ICS_IF_VOIP		3206
 wlf_cragg_6410		MACH_WLF_CRAGG_6410	WLF_CRAGG_6410		3207

arch/arm64/include/asm/cacheflush.h

@@ -138,19 +138,10 @@ static inline void __flush_icache_all(void)
 #define flush_icache_page(vma,page)	do { } while (0)
 
 /*
- * flush_cache_vmap() is used when creating mappings (eg, via vmap,
- * vmalloc, ioremap etc) in kernel space for pages.  On non-VIPT
- * caches, since the direct-mappings of these pages may contain cached
- * data, we need to do a full cache flush to ensure that writebacks
- * don't corrupt data placed into these pages via the new mappings.
+ * Not required on AArch64 (PIPT or VIPT non-aliasing D-cache).
  */
 static inline void flush_cache_vmap(unsigned long start, unsigned long end)
 {
-	/*
-	 * set_pte_at() called from vmap_pte_range() does not
-	 * have a DSB after cleaning the cache line.
-	 */
-	dsb(ish);
 }
 
 static inline void flush_cache_vunmap(unsigned long start, unsigned long end)

arch/arm64/include/asm/hw_breakpoint.h

@@ -79,7 +79,6 @@ static inline void decode_ctrl_reg(u32 reg,
  */
 #define ARM_MAX_BRP		16
 #define ARM_MAX_WRP		16
-#define ARM_MAX_HBP_SLOTS	(ARM_MAX_BRP + ARM_MAX_WRP)
 
 /* Virtual debug register bases. */
 #define AARCH64_DBG_REG_BVR	0

arch/arm64/include/asm/pgtable.h

@@ -138,6 +138,8 @@ extern struct page *empty_zero_page;
 
 #define pte_valid_user(pte) \
 	((pte_val(pte) & (PTE_VALID | PTE_USER)) == (PTE_VALID | PTE_USER))
+#define pte_valid_not_user(pte) \
+	((pte_val(pte) & (PTE_VALID | PTE_USER)) == PTE_VALID)
 
 static inline pte_t pte_wrprotect(pte_t pte)
 {
@@ -184,6 +186,15 @@ static inline pte_t pte_mkspecial(pte_t pte)
 static inline void set_pte(pte_t *ptep, pte_t pte)
 {
 	*ptep = pte;
+
+	/*
+	 * Only if the new pte is valid and kernel, otherwise TLB maintenance
+	 * or update_mmu_cache() have the necessary barriers.
+	 */
+	if (pte_valid_not_user(pte)) {
+		dsb(ishst);
+		isb();
+	}
 }
 
 extern void __sync_icache_dcache(pte_t pteval, unsigned long addr);
@@ -303,6 +314,7 @@ static inline void set_pmd(pmd_t *pmdp, pmd_t pmd)
 {
 	*pmdp = pmd;
 	dsb(ishst);
+	isb();
 }
 
 static inline void pmd_clear(pmd_t *pmdp)
@@ -333,6 +345,7 @@ static inline void set_pud(pud_t *pudp, pud_t pud)
 {
 	*pudp = pud;
 	dsb(ishst);
+	isb();
 }
 
 static inline void pud_clear(pud_t *pudp)

arch/arm64/include/asm/ptrace.h

@@ -137,7 +137,7 @@ struct pt_regs {
 	(!((regs)->pstate & PSR_F_BIT))
 
 #define user_stack_pointer(regs) \
-	(!compat_user_mode(regs)) ? ((regs)->sp) : ((regs)->compat_sp)
+	(!compat_user_mode(regs) ? (regs)->sp : (regs)->compat_sp)
 
 static inline unsigned long regs_return_value(struct pt_regs *regs)
 {

arch/arm64/include/asm/tlbflush.h

@@ -122,6 +122,7 @@ static inline void flush_tlb_kernel_range(unsigned long start, unsigned long end
 	for (addr = start; addr < end; addr += 1 << (PAGE_SHIFT - 12))
 		asm("tlbi vaae1is, %0" : : "r"(addr));
 	dsb(ish);
+	isb();
 }
 
 /*
@@ -131,8 +132,8 @@ static inline void update_mmu_cache(struct vm_area_struct *vma,
 				    unsigned long addr, pte_t *ptep)
 {
 	/*
-	 * set_pte() does not have a DSB, so make sure that the page table
-	 * write is visible.
+	 * set_pte() does not have a DSB for user mappings, so make sure that
+	 * the page table write is visible.
 	 */
 	dsb(ishst);
 }

arch/arm64/kernel/debug-monitors.c

@@ -315,12 +315,7 @@ static int brk_handler(unsigned long addr, unsigned int esr,
 {
 	siginfo_t info;
 
-	if (call_break_hook(regs, esr) == DBG_HOOK_HANDLED)
-		return 0;
-
-	if (!user_mode(regs))
-		return -EFAULT;
-
+	if (user_mode(regs)) {
 		info = (siginfo_t) {
 			.si_signo = SIGTRAP,
 			.si_errno = 0,
@@ -329,6 +324,11 @@ static int brk_handler(unsigned long addr, unsigned int esr,
 		};
 
 		force_sig_info(SIGTRAP, &info, current);
+	} else if (call_break_hook(regs, esr) != DBG_HOOK_HANDLED) {
+		pr_warning("Unexpected kernel BRK exception at EL1\n");
+		return -EFAULT;
+	}
+
 	return 0;
 }
 

arch/arm64/kernel/efi.c

@@ -464,6 +464,8 @@ static int __init arm64_enter_virtual_mode(void)
 
 	set_bit(EFI_RUNTIME_SERVICES, &efi.flags);
 
+	efi.runtime_version = efi.systab->hdr.revision;
+
 	return 0;
 }
 early_initcall(arm64_enter_virtual_mode);

arch/arm64/kernel/irq.c

@@ -97,19 +97,15 @@ static bool migrate_one_irq(struct irq_desc *desc)
 	if (irqd_is_per_cpu(d) || !cpumask_test_cpu(smp_processor_id(), affinity))
 		return false;
 
-	if (cpumask_any_and(affinity, cpu_online_mask) >= nr_cpu_ids)
-		ret = true;
-
-	/*
-	 * when using forced irq_set_affinity we must ensure that the cpu
-	 * being offlined is not present in the affinity mask, it may be
-	 * selected as the target CPU otherwise
-	 */
+	if (cpumask_any_and(affinity, cpu_online_mask) >= nr_cpu_ids) {
 		affinity = cpu_online_mask;
+		ret = true;
+	}
+
 	c = irq_data_get_irq_chip(d);
 	if (!c->irq_set_affinity)
 		pr_debug("IRQ%u: unable to set affinity\n", d->irq);
-	else if (c->irq_set_affinity(d, affinity, true) == IRQ_SET_MASK_OK && ret)
+	else if (c->irq_set_affinity(d, affinity, false) == IRQ_SET_MASK_OK && ret)
 		cpumask_copy(d->affinity, affinity);
 
 	return ret;