Pass the DRM connector name to any configured backlight
device so that userspace can associate the two items.
Ideally this should be in drm_panel, but it is bridge/panel
that creates the drm_connector and therefore knows the name.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The naming of backlight devices is not terribly useful for
associating a backlight controller with a display (assuming
it is attached to one).
Add a sysfs node that will return a display name that can be set
by other subsystems.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The camera sync parameter declarations include are invalid in that they
have both embedded string values and following cell values. The
intention here was to use the cell values, but the embedded "0" was
not removed as it should have been.
The implication of this mistake is that inverted sync flags would be
ignored because the 0 value corresponds to GPIO_ACTIVE_HIGH. The
extra cell value would be treated as the start of another override,
but then ignored because the end of the parameter is reached.
These errors should have been picked up by the automated checks, but
the base dts files weren't subjected to the same validation. This has
now been corrected.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
If a set of read requests are issued by an endpoint, they are streamed
into a resynchronisation FIFO prior to exiting the RC. This FIFO has an
edge case where it can drop QoS for a request to 0 if there's a single
outstanding read request in the FIFO, and another is pushed when the
FIFO is popped. Requests with a QoS of 0 can take hundreds of
microseconds to complete.
By adding an experimentally-determined amount of backpressure on the pop
side, the critical level transition can largely be avoided.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
The stride value reported for output image buffers should be at least
as large as any value that was passed in by the caller (subject to
correct alignment for the pixel format). If the value is zero (meaning
no value was passed), or is too small, the minimum acceptable value
will be substituted.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Interop testing with the M.2 HAT has revealed that there are many quirky
endpoint devices out there, so users should have a way of rapidly
iterating to find which quirk is causing reliability issues.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
L1 sub-states require the connection of the CLKREQ# auxiliary signal
which is a PCB-level decision, and also depends on the vagrancies of
adapters/interposers/slots that may exist between the chip and the
endpoint.
If this parameter is present, and the RC driver sees an L1 substate
capability in the endpoint, then the result is a broken link if CLKREQ#
isn't end-to-end connected - regardless of the state of the L1.x enable
bits in the RC.
Board-specific methods (HAT+ overlay, board DTB) should define this
property if required.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
There are no MEDIA_BUS_FMT_* defines for GRB or BRG, and adding
them is a pain.
Add a DT override to allow setting the order.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
As with many microcontrollers, the panel wants to use clock
stretching during a read so that the appropriate return value
can be generated and programmed into the hardware.
With Pi0-3 really not supporting clock stretching, this resulted
in the panel firmware dying.
Insert a delay between the write and the read to give the firmware
a chance to generate the relevant return value.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
commit 6cf3506587 upstream.
If kobject_add() is fail in bind_rdev_to_array(), 'rdev->serial' will be
alloc not be freed, and kmemleak occurs.
unreferenced object 0xffff88815a350000 (size 49152):
comm "mdadm", pid 789, jiffies 4294716910
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace (crc f773277a):
[<0000000058b0a453>] kmemleak_alloc+0x61/0xe0
[<00000000366adf14>] __kmalloc_large_node+0x15e/0x270
[<000000002e82961b>] __kmalloc_node.cold+0x11/0x7f
[<00000000f206d60a>] kvmalloc_node+0x74/0x150
[<0000000034bf3363>] rdev_init_serial+0x67/0x170
[<0000000010e08fe9>] mddev_create_serial_pool+0x62/0x220
[<00000000c3837bf0>] bind_rdev_to_array+0x2af/0x630
[<0000000073c28560>] md_add_new_disk+0x400/0x9f0
[<00000000770e30ff>] md_ioctl+0x15bf/0x1c10
[<000000006cfab718>] blkdev_ioctl+0x191/0x3f0
[<0000000085086a11>] vfs_ioctl+0x22/0x60
[<0000000018b656fe>] __x64_sys_ioctl+0xba/0xe0
[<00000000e54e675e>] do_syscall_64+0x71/0x150
[<000000008b0ad622>] entry_SYSCALL_64_after_hwframe+0x6c/0x74
Fixes: 963c555e75 ("md: introduce mddev_create/destroy_wb_pool for the change of member device")
Signed-off-by: Li Nan <linan122@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20240208085556.2412922-1-linan666@huaweicloud.com
[ mddev_destroy_serial_pool third parameter was removed in mainline,
where there is no need to suspend within this function anymore. ]
Signed-off-by: Jeremy Bongio <jbongio@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1db7959aac upstream.
[BUG]
There is a recent report that when memory pressure is high (including
cached pages), btrfs can spend most of its time on memory allocation in
btrfs_alloc_page_array() for compressed read/write.
[CAUSE]
For btrfs_alloc_page_array() we always go alloc_pages_bulk_array(), and
even if the bulk allocation failed (fell back to single page
allocation) we still retry but with extra memalloc_retry_wait().
If the bulk alloc only returned one page a time, we would spend a lot of
time on the retry wait.
The behavior was introduced in commit 395cb57e85 ("btrfs: wait between
incomplete batch memory allocations").
[FIX]
Although the commit mentioned that other filesystems do the wait, it's
not the case at least nowadays.
All the mainlined filesystems only call memalloc_retry_wait() if they
failed to allocate any page (not only for bulk allocation).
If there is any progress, they won't call memalloc_retry_wait() at all.
For example, xfs_buf_alloc_pages() would only call memalloc_retry_wait()
if there is no allocation progress at all, and the call is not for
metadata readahead.
So I don't believe we should call memalloc_retry_wait() unconditionally
for short allocation.
Call memalloc_retry_wait() if it fails to allocate any page for tree
block allocation (which goes with __GFP_NOFAIL and may not need the
special handling anyway), and reduce the latency for
btrfs_alloc_page_array().
Reported-by: Julian Taylor <julian.taylor@1und1.de>
Tested-by: Julian Taylor <julian.taylor@1und1.de>
Link: https://lore.kernel.org/all/8966c095-cbe7-4d22-9784-a647d1bf27c3@1und1.de/
Fixes: 395cb57e85 ("btrfs: wait between incomplete batch memory allocations")
CC: stable@vger.kernel.org # 6.1+
Reviewed-by: Sweet Tea Dorminy <sweettea-kernel@dorminy.me>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6827738dc6 upstream.
After the patch to restrict the use of mmap() to CAP_SYS_RAWIO for
the currently existing devices, most applications can no longer make
use of the accelerators as in production "you don't run things as root".
To keep the DSA and IAA accelerators usable, hook up a write() method
so that applications can still submit work. In the write method,
sufficient input validation is performed to avoid the security issue
that required the mmap CAP_SYS_RAWIO check.
One complication is that the DSA device allows for indirect ("batched")
descriptors. There is no reasonable way to do the input validation
on these indirect descriptors so the write() method will not allow these
to be submitted to the hardware on affected hardware, and the sysfs
enumeration of support for the opcode is also removed.
Early performance data shows that the performance delta for most common
cases is within the noise.
Signed-off-by: Nikhil Rao <nikhil.rao@intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e11452eb07 upstream.
On Sapphire Rapids and related platforms, the DSA and IAA devices have an
erratum that causes direct access (for example, by using the ENQCMD or
MOVDIR64 instructions) from untrusted applications to be a security problem.
To solve this, add a flag to the PCI device enumeration and device structures
to indicate the presence/absence of this security exposure. In the mmap()
method of the device, this flag is then used to enforce that the user
has the CAP_SYS_RAWIO capability.
In a future patch, a write() based method will be added that allows untrusted
applications submit work to the accelerator, where the kernel can do
sanity checking on the user input to ensure secure operation of the accelerator.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 95feb3160e upstream.
Due to an erratum with the SPR_DSA and SPR_IAX devices, it is not secure to assign
these devices to virtual machines. Add the PCI IDs of these devices to the VFIO
denylist to ensure that this is handled appropriately by the VFIO subsystem.
The SPR_DSA and SPR_IAX devices are on-SOC devices for the Sapphire Rapids
(and related) family of products that perform data movement and compression.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40d442f969 upstream.
A recent commit fixed the code that parses the firmware files before
downloading them to the controller but introduced a memory leak in case
the sanity checks ever fail.
Make sure to free the firmware buffer before returning on errors.
Fixes: f905ae0be4b7 ("Bluetooth: qca: add missing firmware sanity checks")
Cc: stable@vger.kernel.org # 4.19
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cda0d6a198 upstream.
Add the missing sanity checks and move the 255-byte build-id buffer off
the stack to avoid leaking stack data through debugfs in case the
build-info reply is malformed.
Fixes: c0187b0bd3 ("Bluetooth: btqca: Add support to read FW build version for WCN3991 BTSoC")
Cc: stable@vger.kernel.org # 5.12
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd336649ba upstream.
The default device address apparently comes from the NVM configuration
file and can differ quite a bit between controllers.
Store the default address when parsing the configuration file and use it
to determine whether the controller has been provisioned with an
address.
This makes sure that devices without a unique address start as
unconfigured unless a valid address has been provided in the devicetree.
Fixes: 32868e126c ("Bluetooth: qca: fix invalid device address check")
Cc: stable@vger.kernel.org # 6.5
Cc: Doug Anderson <dianders@chromium.org>
Cc: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a112d3c72a upstream.
The NVM configuration files used by WCN3988 and WCN3990/1/8 have two
sets of configuration tags that are enclosed by a type-length header of
type four which the current parser fails to account for.
Instead the driver happily parses random data as if it were valid tags,
something which can lead to the configuration data being corrupted if it
ever encounters the words 0x0011 or 0x001b.
As is clear from commit b63882549b ("Bluetooth: btqca: Fix the NVM
baudrate tag offcet for wcn3991") the intention has always been to
process the configuration data also for WCN3991 and WCN3998 which
encodes the baud rate at a different offset.
Fix the parser so that it can handle the WCN3xxx configuration files,
which has an enclosing type-length header of type four and two sets of
TLV tags enclosed by a type-length header of type two and three,
respectively.
Note that only the first set, which contains the tags the driver is
currently looking for, will be parsed for now.
With the parser fixed, the software in-band sleep bit will now be set
for WCN3991 and WCN3998 (as it is for later controllers) and the default
baud rate 3200000 may be updated by the driver also for WCN3xxx
controllers.
Notably the deep-sleep feature bit is already set by default in all
configuration files in linux-firmware.
Fixes: 4219d46868 ("Bluetooth: btqca: Add wcn3990 firmware download support.")
Cc: stable@vger.kernel.org # 4.19
Cc: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e4edfa1e2 upstream.
Add the missing sanity checks when parsing the firmware files before
downloading them to avoid accessing and corrupting memory beyond the
vmalloced buffer.
Fixes: 83e81961ff ("Bluetooth: btqca: Introduce generic QCA ROME support")
Cc: stable@vger.kernel.org # 4.10
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66c39332d0 upstream.
Qualcomm Bluetooth controllers may not have been provisioned with a
valid device address and instead end up using the default address
00:00:00:00:5a:ad.
This address is now used to determine if a controller has a valid
address or if one needs to be provided through devicetree or by user
space before the controller can be used.
It turns out that the WCN3991 controllers used in Chromium Trogdor
machines use a different default address, 39:98:00:00:5a:ad, which also
needs to be marked as invalid so that the correct address is fetched
from the devicetree.
Qualcomm has unfortunately not yet provided any answers as to whether
the 39:98 encodes a hardware id and if there are other variants of the
default address that needs to be handled by the driver.
For now, add the Trogdor WCN3991 default address to the device address
check to avoid having these controllers start with the default address
instead of their assigned addresses.
Fixes: 32868e126c ("Bluetooth: qca: fix invalid device address check")
Cc: stable@vger.kernel.org # 6.5
Cc: Doug Anderson <dianders@chromium.org>
Cc: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 32868e126c upstream.
Qualcomm Bluetooth controllers may not have been provisioned with a
valid device address and instead end up using the default address
00:00:00:00:5a:ad.
This was previously believed to be due to lack of persistent storage for
the address but it may also be due to integrators opting to not use the
on-chip OTP memory and instead store the address elsewhere (e.g. in
storage managed by secure world firmware).
According to Qualcomm, at least WCN6750, WCN6855 and WCN7850 have
on-chip OTP storage for the address.
As the device type alone cannot be used to determine when the address is
valid, instead read back the address during setup() and only set the
HCI_QUIRK_USE_BDADDR_PROPERTY flag when needed.
This specifically makes sure that controllers that have been provisioned
with an address do not start as unconfigured.
Reported-by: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Link: https://lore.kernel.org/r/124a7d54-5a18-4be7-9a76-a12017f6cce5@quicinc.com/
Fixes: 5971752de4 ("Bluetooth: hci_qca: Set HCI_QUIRK_USE_BDADDR_PROPERTY for wcn3990")
Fixes: e668eb1e15 ("Bluetooth: hci_core: Don't stop BT if the BD address missing in dts")
Fixes: 6945795bc8 ("Bluetooth: fix use-bdaddr-property quirk")
Cc: stable@vger.kernel.org # 6.5
Cc: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reported-by: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 22e61e15af upstream.
Treat the events directory the same as other directories when it comes to
permissions. The events directory was considered different because it's
dentry is persistent, whereas the other directory dentries are created
when accessed. But the way tracefs now does its ownership by using the
root dentry's permissions as the default permissions, the events directory
can get out of sync when a remount is performed setting the group and user
permissions.
Remove the special case for the events directory on setting the
attributes. This allows the updates caused by remount to work properly as
well as simplifies the code.
Link: https://lore.kernel.org/linux-trace-kernel/20240502200906.002923579@goodmis.org
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Fixes: 8186fff7ab ("tracefs/eventfs: Use root and instance inodes as default ownership")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6599bd5517 upstream.
If the instances directory's permissions were never change, then have it
and its children use the mount point permissions as the default.
Currently, the permissions of instance directories are determined by the
instance directory's permissions itself. But if the tracefs file system is
remounted and changes the permissions, the instance directory and its
children should use the new permission.
But because both the instance directory and its children use the instance
directory's inode for permissions, it misses the update.
To demonstrate this:
# cd /sys/kernel/tracing/
# mkdir instances/foo
# ls -ld instances/foo
drwxr-x--- 5 root root 0 May 1 19:07 instances/foo
# ls -ld instances
drwxr-x--- 3 root root 0 May 1 18:57 instances
# ls -ld current_tracer
-rw-r----- 1 root root 0 May 1 18:57 current_tracer
# mount -o remount,gid=1002 .
# ls -ld instances
drwxr-x--- 3 root root 0 May 1 18:57 instances
# ls -ld instances/foo/
drwxr-x--- 5 root root 0 May 1 19:07 instances/foo/
# ls -ld current_tracer
-rw-r----- 1 root lkp 0 May 1 18:57 current_tracer
Notice that changing the group id to that of "lkp" did not affect the
instances directory nor its children. It should have been:
# ls -ld current_tracer
-rw-r----- 1 root root 0 May 1 19:19 current_tracer
# ls -ld instances/foo/
drwxr-x--- 5 root root 0 May 1 19:25 instances/foo/
# ls -ld instances
drwxr-x--- 3 root root 0 May 1 19:19 instances
# mount -o remount,gid=1002 .
# ls -ld current_tracer
-rw-r----- 1 root lkp 0 May 1 19:19 current_tracer
# ls -ld instances
drwxr-x--- 3 root lkp 0 May 1 19:19 instances
# ls -ld instances/foo/
drwxr-x--- 5 root lkp 0 May 1 19:25 instances/foo/
Where all files were updated by the remount gid update.
Link: https://lore.kernel.org/linux-trace-kernel/20240502200905.686838327@goodmis.org
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Fixes: 8186fff7ab ("tracefs/eventfs: Use root and instance inodes as default ownership")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit baa23a8d43 upstream.
There's an inconsistency with the way permissions are handled in tracefs.
Because the permissions are generated when accessed, they default to the
root inode's permission if they were never set by the user. If the user
sets the permissions, then a flag is set and the permissions are saved via
the inode (for tracefs files) or an internal attribute field (for
eventfs).
But if a remount happens that specify the permissions, all the files that
were not changed by the user gets updated, but the ones that were are not.
If the user were to remount the file system with a given permission, then
all files and directories within that file system should be updated.
This can cause security issues if a file's permission was updated but the
admin forgot about it. They could incorrectly think that remounting with
permissions set would update all files, but miss some.
For example:
# cd /sys/kernel/tracing
# chgrp 1002 current_tracer
# ls -l
[..]
-rw-r----- 1 root root 0 May 1 21:25 buffer_size_kb
-rw-r----- 1 root root 0 May 1 21:25 buffer_subbuf_size_kb
-r--r----- 1 root root 0 May 1 21:25 buffer_total_size_kb
-rw-r----- 1 root lkp 0 May 1 21:25 current_tracer
-rw-r----- 1 root root 0 May 1 21:25 dynamic_events
-r--r----- 1 root root 0 May 1 21:25 dyn_ftrace_total_info
-r--r----- 1 root root 0 May 1 21:25 enabled_functions
Where current_tracer now has group "lkp".
# mount -o remount,gid=1001 .
# ls -l
-rw-r----- 1 root tracing 0 May 1 21:25 buffer_size_kb
-rw-r----- 1 root tracing 0 May 1 21:25 buffer_subbuf_size_kb
-r--r----- 1 root tracing 0 May 1 21:25 buffer_total_size_kb
-rw-r----- 1 root lkp 0 May 1 21:25 current_tracer
-rw-r----- 1 root tracing 0 May 1 21:25 dynamic_events
-r--r----- 1 root tracing 0 May 1 21:25 dyn_ftrace_total_info
-r--r----- 1 root tracing 0 May 1 21:25 enabled_functions
Everything changed but the "current_tracer".
Add a new link list that keeps track of all the tracefs_inodes which has
the permission flags that tell if the file/dir should use the root inode's
permission or not. Then on remount, clear all the flags so that the
default behavior of using the root inode's permission is done for all
files and directories.
Link: https://lore.kernel.org/linux-trace-kernel/20240502200905.529542160@goodmis.org
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Fixes: 8186fff7ab ("tracefs/eventfs: Use root and instance inodes as default ownership")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 691aae4f36 upstream.
This patch fix xfstests generic/070 test with smb2 leases = yes.
cifs.ko doesn't set parent lease key and epoch in create context v2 lease.
ksmbd suppose that parent lease and epoch are vaild if data length is
v2 lease context size and handle directory lease using this values.
ksmbd should hanle it as v1 lease not v2 lease if parent lease key and
epoch are not set in create context v2 lease.
Cc: stable@vger.kernel.org
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 97c2ec6466 upstream.
This patch fixes generic/011 when enable smb2 leases.
if ksmbd sends multiple notifications for a file, cifs increments
the reference count of the file but it does not decrement the count by
the failure of queue_work.
So even if the file is closed, cifs does not send a SMB2_CLOSE request.
Cc: stable@vger.kernel.org
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc00bc83f2 upstream.
ΕΛΕΝΗ reported that ksmbd binds to the IPV6 wildcard (::) by default for
ipv4 and ipv6 binding. So IPV4 connections are successful only when
the Linux system parameter bindv6only is set to 0 [default value].
If this parameter is set to 1, then the ipv6 wildcard only represents
any IPV6 address. Samba creates different sockets for ipv4 and ipv6
by default. This patch off sk_ipv6only to support IPV4/IPV6 connections
without creating two sockets.
Cc: stable@vger.kernel.org
Reported-by: ΕΛΕΝΗ ΤΖΑΒΕΛΛΑ <helentzavellas@yahoo.gr>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a4b49bb58 upstream.
regulator_get() may sometimes be called more than once for the same
consumer device, something which before commit dbe954d8f1 ("regulator:
core: Avoid debugfs: Directory ... already present! error") resulted in
errors being logged.
A couple of recent commits broke the handling of such cases so that
attributes are now erroneously created in the debugfs root directory the
second time a regulator is requested and the log is filled with errors
like:
debugfs: File 'uA_load' in directory '/' already present!
debugfs: File 'min_uV' in directory '/' already present!
debugfs: File 'max_uV' in directory '/' already present!
debugfs: File 'constraint_flags' in directory '/' already present!
on any further calls.
Fixes: 2715bb11cf ("regulator: core: Fix more error checking for debugfs_create_dir()")
Fixes: 08880713ce ("regulator: core: Streamline debugfs operations")
Cc: stable@vger.kernel.org
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240509133304.8883-1-johan+linaro@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d5887dc6b6 upstream.
Sandisk SN530 NVMe drives have broken MSIs. On systems without MSI-X
support, all commands time out resulting in the following message:
nvme nvme0: I/O tag 12 (100c) QID 0 timeout, completion polled
These timeouts cause the boot to take an excessively-long time (over 20
minutes) while the initial command queue is flushed.
Address this by adding a quirk for drives with buggy MSIs. The lspci
output for this device (recorded on a system with MSI-X support) is:
02:00.0 Non-Volatile memory controller: Sandisk Corp Device 5008 (rev 01) (prog-if 02 [NVM Express])
Subsystem: Sandisk Corp Device 5008
Flags: bus master, fast devsel, latency 0, IRQ 16, NUMA node 0
Memory at f7e00000 (64-bit, non-prefetchable) [size=16K]
Memory at f7e04000 (64-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 3
Capabilities: [90] MSI: Enable- Count=1/32 Maskable- 64bit+
Capabilities: [b0] MSI-X: Enable+ Count=17 Masked-
Capabilities: [c0] Express Endpoint, MSI 00
Capabilities: [100] Advanced Error Reporting
Capabilities: [150] Device Serial Number 00-00-00-00-00-00-00-00
Capabilities: [1b8] Latency Tolerance Reporting
Capabilities: [300] Secondary PCI Express
Capabilities: [900] L1 PM Substates
Kernel driver in use: nvme
Kernel modules: nvme
Cc: <stable@vger.kernel.org>
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c88033efe9 upstream.
Userfaultfd unregister includes a step to remove wr-protect bits from all
the relevant pgtable entries, but that only covered an explicit
UFFDIO_UNREGISTER ioctl, not a close() on the userfaultfd itself. Cover
that too. This fixes a WARN trace.
The only user visible side effect is the user can observe leftover
wr-protect bits even if the user close()ed on an userfaultfd when
releasing the last reference of it. However hopefully that should be
harmless, and nothing bad should happen even if so.
This change is now more important after the recent page-table-check
patch we merged in mm-unstable (446dd9ad37d0 ("mm/page_table_check:
support userfault wr-protect entries")), as we'll do sanity check on
uffd-wp bits without vma context. So it's better if we can 100%
guarantee no uffd-wp bit leftovers, to make sure each report will be
valid.
Link: https://lore.kernel.org/all/000000000000ca4df20616a0fe16@google.com/
Fixes: f369b07c86 ("mm/uffd: reset write protection when unregister with wp-mode")
Analyzed-by: David Hildenbrand <david@redhat.com>
Link: https://lkml.kernel.org/r/20240422133311.2987675-1-peterx@redhat.com
Reported-by: syzbot+d8426b591c36b21c750e@syzkaller.appspotmail.com
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Cc: Nadav Amit <nadav.amit@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e6423441b upstream.
In commit 0518dbe97f ("selftests/mm: fix cross compilation with LLVM")
the logic to detect the machine architecture in the Makefile was changed
to use ARCH, and only fallback to uname -m if ARCH is unset. However the
tests of ARCH were not updated to account for the fact that ARCH is
"powerpc" for powerpc builds, not "ppc64".
Fix it by changing the checks to look for "powerpc", and change the
uname -m logic to convert "ppc64.*" into "powerpc".
With that fixed the following tests now build for powerpc again:
* protection_keys
* va_high_addr_switch
* virtual_address_range
* write_to_hugetlbfs
Link: https://lkml.kernel.org/r/20240506115825.66415-1-mpe@ellerman.id.au
Fixes: 0518dbe97f ("selftests/mm: fix cross compilation with LLVM")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org> [6.4+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 720a22fd6c upstream.
With 'iommu=off' on the kernel command line and x2APIC enabled by the BIOS
the code which disables the x2APIC triggers an unchecked MSR access error:
RDMSR from 0x802 at rIP: 0xffffffff94079992 (native_apic_msr_read+0x12/0x50)
This is happens because default_acpi_madt_oem_check() selects an x2APIC
driver before the x2APIC is disabled.
When the x2APIC is disabled because interrupt remapping cannot be enabled
due to 'iommu=off' on the command line, x2apic_disable() invokes
apic_set_fixmap() which in turn tries to read the APIC ID. This triggers
the MSR warning because x2APIC is disabled, but the APIC driver is still
x2APIC based.
Prevent that by adding an argument to apic_set_fixmap() which makes the
APIC ID read out conditional and set it to false from the x2APIC disable
path. That's correct as the APIC ID has already been read out during early
discovery.
Fixes: d10a904435 ("x86/apic: Consolidate boot_cpu_physical_apicid initialization sites")
Reported-by: Adrian Huang <ahuang12@lenovo.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Adrian Huang <ahuang12@lenovo.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/875xw5t6r7.ffs@tglx
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a26ff37e62 upstream.
net_alloc_generic is called by net_alloc, which is called without any
locking. It reads max_gen_ptrs, which is changed under pernet_ops_rwsem. It
is read twice, first to allocate an array, then to set s.len, which is
later used to limit the bounds of the array access.
It is possible that the array is allocated and another thread is
registering a new pernet ops, increments max_gen_ptrs, which is then used
to set s.len with a larger than allocated length for the variable array.
Fix it by reading max_gen_ptrs only once in net_alloc_generic. If
max_gen_ptrs is later incremented, it will be caught in net_assign_generic.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com>
Fixes: 073862ba5d ("netns: fix net_alloc_generic()")
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240502132006.3430840-1-cascardo@igalia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 819fe8c96a upstream.
There are two issues with SDHC2 configuration for SA8155P-ADP,
which prevent use of SDHC2 and causes issues with ethernet:
- Card Detect pin for SHDC2 on SA8155P-ADP is connected to gpio4 of
PMM8155AU_1, not to SoC itself. SoC's gpio4 is used for DWMAC
TX. If sdhc driver probes after dwmac driver, it reconfigures
gpio4 and this breaks Ethernet MAC.
- pinctrl configuration mentions gpio96 as CD pin. It seems it was
copied from some SM8150 example, because as mentioned above,
correct CD pin is gpio4 on PMM8155AU_1.
This patch fixes both mentioned issues by providing correct pin handle
and pinctrl configuration.
Fixes: 0deb2624e2 ("arm64: dts: qcom: sa8155p-adp: Add support for uSD card")
Cc: stable@vger.kernel.org
Signed-off-by: Volodymyr Babchuk <volodymyr_babchuk@epam.com>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20240412190310.1647893-1-volodymyr_babchuk@epam.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 892b41b16f upstream.
[Why] DSC debugfs, such as dp_dsc_clock_en_read,
use aconnector->dc_link to find pipe_ctx for display.
Displays connected to MST hub share the same dc_link.
DSC instance is from pipe_ctx. This causes incorrect
DSC instance for display connected to MST hub.
[How] Add aconnector->sink check to find pipe_ctx.
CC: stable@vger.kernel.org
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 43b26bdd2e upstream.
Starting BDB version 239, hdr_dpcd_refresh_timeout is introduced to
backlight BDB data. Commit 700034566d ("drm/i915/bios: Define more BDB
contents") updated the backlight BDB data accordingly. This broke the
parsing of backlight BDB data in VBT for versions 236 - 238 (both
inclusive) and hence the backlight controls are not responding on units
with the concerned BDB version.
backlight_control information has been present in backlight BDB data
from at least BDB version 191 onwards, if not before. Hence this patch
extracts the backlight_control information for BDB version 191 or newer.
Tested on Chromebooks using Jasperlake SoC (reports bdb->version = 236).
Tested on Chromebooks using Raptorlake SoC (reports bdb->version = 251).
v2: removed checking the block size of the backlight BDB data
[vsyrjala: this is completely safe thanks to commit e163cfb4c9
("drm/i915/bios: Make copies of VBT data blocks")]
Fixes: 700034566d ("drm/i915/bios: Define more BDB contents")
Cc: stable@vger.kernel.org
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@chromium.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240221180622.v2.1.I0690aa3e96a83a43b3fc33f50395d334b2981826@changeid
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
(cherry picked from commit c286f6a973)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit be4a2a81b6 upstream.
We don't get the right offset in that case. The GPU has
an unused 4K area of the register BAR space into which you can
remap registers. We remap the HDP flush registers into this
space to allow userspace (CPU or GPU) to flush the HDP when it
updates VRAM. However, on systems with >4K pages, we end up
exposing PAGE_SIZE of MMIO space.
Fixes: d8e408a827 ("drm/amdkfd: Expose HDP registers to user space")
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a222a6470d upstream.
This reverts commit 52a6947bf5.
This causes loading failures in
[ 0.367379] nouveau 0000:01:00.0: NVIDIA GP104 (134000a1)
[ 0.474499] nouveau 0000:01:00.0: bios: version 86.04.50.80.13
[ 0.474620] nouveau 0000:01:00.0: pmu: firmware unavailable
[ 0.474977] nouveau 0000:01:00.0: fb: 8192 MiB GDDR5
[ 0.484371] nouveau 0000:01:00.0: sec2(acr): mbox 00000001 00000000
[ 0.484377] nouveau 0000:01:00.0: sec2(acr):load: boot failed: -5
[ 0.484379] nouveau 0000:01:00.0: acr: init failed, -5
[ 0.484466] nouveau 0000:01:00.0: init failed with -5
[ 0.484468] nouveau: DRM-master:00000000:00000080: init failed with -5
[ 0.484470] nouveau 0000:01:00.0: DRM-master: Device allocation failed: -5
[ 0.485078] nouveau 0000:01:00.0: probe with driver nouveau failed with error -50
I tried tracking it down but ran out of time this week, will revisit next week.
Reported-by: Dan Moulding <dan@danm.net>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d18ca8635d upstream.
When using davinci-mcasp as CPU DAI with simple-card, there are some
conditions that cause simple-card to finish registering a sound card before
davinci-mcasp finishes registering all sound components. This creates a
non-working sound card from userspace with no problem indication apart
from not being able to play/record audio on a PCM stream. The issue
arises during simultaneous probe execution of both drivers. Specifically,
the simple-card driver, awaiting a CPU DAI, proceeds as soon as
davinci-mcasp registers its DAI. However, this process can lead to the
client mutex lock (client_mutex in soc-core.c) being held or davinci-mcasp
being preempted before PCM DMA registration on davinci-mcasp finishes.
This situation occurs when the probes of both drivers run concurrently.
Below is the code path for this condition. To solve the issue, defer
davinci-mcasp CPU DAI registration to the last step in the audio part of
it. This way, simple-card CPU DAI parsing will be deferred until all
audio components are registered.
Fail Code Path:
simple-card.c: probe starts
simple-card.c: simple_dai_link_of: simple_parse_node(..,cpu,..) returns EPROBE_DEFER, no CPU DAI yet
davinci-mcasp.c: probe starts
davinci-mcasp.c: devm_snd_soc_register_component() register CPU DAI
simple-card.c: probes again, finish CPU DAI parsing and call devm_snd_soc_register_card()
simple-card.c: finish probe
davinci-mcasp.c: *dma_pcm_platform_register() register PCM DMA
davinci-mcasp.c: probe finish
Cc: stable@vger.kernel.org
Fixes: 9fbd58cf4a ("ASoC: davinci-mcasp: Choose PCM driver based on configured DMA controller")
Signed-off-by: Joao Paulo Goncalves <joao.goncalves@toradex.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Reviewed-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240417184138.1104774-1-jpaulo.silvagoncalves@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0d5e2a8223 upstream.
The UMAC_CMD register is written from different execution
contexts and has insufficient synchronization protections to
prevent possible corruption. Of particular concern are the
acceses from the phy_device delayed work context used by the
adjust_link call and the BH context that may be used by the
ndo_set_rx_mode call.
A spinlock is added to the driver to protect contended register
accesses (i.e. reg_lock) and it is used to synchronize accesses
to UMAC_CMD.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Cc: stable@vger.kernel.org
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2dbe5f1936 upstream.
The ndo_set_rx_mode function is synchronized with the
netif_addr_lock spinlock and BHs disabled. Since this
function is also invoked directly from the driver the
same synchronization should be applied.
Fixes: 72f9634762 ("net: bcmgenet: set Rx mode before starting netif")
Cc: stable@vger.kernel.org
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d85cf67a33 upstream.
The EXT_RGMII_OOB_CTRL register can be written from different
contexts. It is predominantly written from the adjust_link
handler which is synchronized by the phydev->lock, but can
also be written from a different context when configuring the
mii in bcmgenet_mii_config().
The chances of contention are quite low, but it is conceivable
that adjust_link could occur during resume when WoL is enabled
so use the phydev->lock synchronizer in bcmgenet_mii_config()
to be sure.
Fixes: afe3f907d2 ("net: bcmgenet: power on MII block for all MII modes")
Cc: stable@vger.kernel.org
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0e60f0b758 upstream.
Xtensa has two-argument MAKE_PC_FROM_RA macro to convert a0 to an actual
return address because when windowed ABI is used call{,x}{4,8,12}
opcodes stuff encoded window size into the top 2 bits of the register
that becomes a return address in the called function. Second argument of
that macro is supposed to be an address having these 2 topmost bits set
correctly, but the comment suggested that that could be the stack
address. However the stack doesn't have to be in the same 1GByte region
as the code, especially in noMMU XIP configurations.
Fix the comment and use either _text or regs->pc as the second argument
for the MAKE_PC_FROM_RA macro.
Cc: stable@vger.kernel.org
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 57a1592784 upstream.
There are 2 issues with interrupt handling in the mxc4005 driver:
1. mxc4005_set_trigger_state() writes MXC4005_REG_INT_MASK1_BIT_DRDYE
(0x01) to INT_MASK1 to enable the interrupt, but to disable the interrupt
it writes ~MXC4005_REG_INT_MASK1_BIT_DRDYE which is 0xfe, so it enables
all other interrupt sources in the INT_SRC1 register. On the MXC4005 this
is not an issue because only bit 0 of the register is used. On the MXC6655
OTOH this is a problem since bit7 is used as TC (Temperature Compensation)
disable bit and writing 1 to this disables Temperature Compensation which
should only be done when running self-tests on the chip.
Write 0 instead of ~MXC4005_REG_INT_MASK1_BIT_DRDYE to disable
the interrupts to fix this.
2. The datasheets for the MXC4005 / MXC6655 do not state what the reset
value for the INT_MASK0 and INT_MASK1 registers is and since these are
write only we also cannot learn this from the hw. Presumably the reset
value for both is all 0, which means all interrupts disabled.
Explicitly set both registers to 0 from mxc4005_chip_init() to ensure
both masks are actually set to 0.
Fixes: 79846e33aa ("iio: accel: mxc4005: add support for mxc6655")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240326113700.56725-2-hdegoede@redhat.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 57a01eafdc upstream.
With cpu_possible_mask=0-63 and cpu_online_mask=0-7 the following
kernel oops was observed:
smp: Bringing up secondary CPUs ...
smp: Brought up 1 node, 8 CPUs
Unable to handle kernel pointer dereference in virtual kernel address space
Failing address: 0000000000000000 TEID: 0000000000000803
[..]
Call Trace:
arch_vcpu_is_preempted+0x12/0x80
select_idle_sibling+0x42/0x560
select_task_rq_fair+0x29a/0x3b0
try_to_wake_up+0x38e/0x6e0
kick_pool+0xa4/0x198
__queue_work.part.0+0x2bc/0x3a8
call_timer_fn+0x36/0x160
__run_timers+0x1e2/0x328
__run_timer_base+0x5a/0x88
run_timer_softirq+0x40/0x78
__do_softirq+0x118/0x388
irq_exit_rcu+0xc0/0xd8
do_ext_irq+0xae/0x168
ext_int_handler+0xbe/0xf0
psw_idle_exit+0x0/0xc
default_idle_call+0x3c/0x110
do_idle+0xd4/0x158
cpu_startup_entry+0x40/0x48
rest_init+0xc6/0xc8
start_kernel+0x3c4/0x5e0
startup_continue+0x3c/0x50
The crash is caused by calling arch_vcpu_is_preempted() for an offline
CPU. To avoid this, select the cpu with cpumask_any_and_distribute()
to mask __pod_cpumask with cpu_online_mask. In case no cpu is left in
the pool, skip the assignment.
tj: This doesn't fully fix the bug as CPUs can still go down between picking
the target CPU and the wake call. Fixing that likely requires adding
cpu_online() test to either the sched or s390 arch code. However, regardless
of how that is fixed, workqueue shouldn't be picking a CPU which isn't
online as that would result in unpredictable and worse behavior.
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Fixes: 8639ecebc9 ("workqueue: Implement non-strict affinity scope for unbound workqueues")
Cc: stable@vger.kernel.org # v6.6+
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd7eb8f83f upstream.
Currently, if an automatically freed allocation is an error pointer that
will lead to a crash. An example of this is in wm831x_gpio_dbg_show().
171 char *label __free(kfree) = gpiochip_dup_line_label(chip, i);
172 if (IS_ERR(label)) {
173 dev_err(wm831x->dev, "Failed to duplicate label\n");
174 continue;
175 }
The auto clean up function should check for error pointers as well,
otherwise we're going to keep hitting issues like this.
Fixes: 54da6a0924 ("locking: Introduce __cleanup() based infrastructure")
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 63a6ce5a1a upstream.
[BUG]
When running generic/287, the following file extent items can be
generated:
item 16 key (258 EXTENT_DATA 2682880) itemoff 15305 itemsize 53
generation 9 type 1 (regular)
extent data disk byte 1378414592 nr 462848
extent data offset 0 nr 462848 ram 2097152
extent compression 0 (none)
Note that file extent item is not a compressed one, but its ram_bytes is
way larger than its disk_num_bytes.
According to btrfs on-disk scheme, ram_bytes should match disk_num_bytes
if it's not a compressed one.
[CAUSE]
Since commit b73a6fd1b1 ("btrfs: split partial dio bios before
submit"), for partial dio writes, we would split the ordered extent.
However the function btrfs_split_ordered_extent() doesn't update the
ram_bytes even it has already shrunk the disk_num_bytes.
Originally the function btrfs_split_ordered_extent() is only introduced
for zoned devices in commit d22002fd37 ("btrfs: zoned: split ordered
extent when bio is sent"), but later commit b73a6fd1b1 ("btrfs: split
partial dio bios before submit") makes non-zoned btrfs affected.
Thankfully for un-compressed file extent, we do not really utilize the
ram_bytes member, thus it won't cause any real problem.
[FIX]
Also update btrfs_ordered_extent::ram_bytes inside
btrfs_split_ordered_extent().
Fixes: d22002fd37 ("btrfs: zoned: split ordered extent when bio is sent")
CC: stable@vger.kernel.org # 5.15+
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ae11f04b45 upstream.
typec_register_partner() does not guarantee partner registration
to always succeed. In the event of failure, port->partner is set
to the error value or NULL. Given that port->partner validity is
not checked, this results in the following crash:
Unable to handle kernel NULL pointer dereference at virtual address xx
pc : run_state_machine+0x1bc8/0x1c08
lr : run_state_machine+0x1b90/0x1c08
..
Call trace:
run_state_machine+0x1bc8/0x1c08
tcpm_state_machine_work+0x94/0xe4
kthread_worker_fn+0x118/0x328
kthread+0x1d0/0x23c
ret_from_fork+0x10/0x20
To prevent the crash, check for port->partner validity before
derefencing it in all the call sites.
Cc: stable@vger.kernel.org
Fixes: c97cd0b4b5 ("usb: typec: tcpm: set initial svdm version based on pd revision")
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240427202812.3435268-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf20c69cf3 upstream.
When a Fast Role Swap control message attempt results in a transition
to ERROR_RECOVERY, the TCPC can still queue a TCPM_SOURCING_VBUS event.
If the event is queued but processed after the tcpm_reset_port() call
in the PORT_RESET state, then the following occurs:
1. tcpm_reset_port() calls tcpm_init_vbus() to reset the vbus sourcing and
sinking state
2. tcpm_pd_event_handler() turns VBUS on before the port is in the default
state.
3. The port resolves as a sink. In the SNK_DISCOVERY state,
tcpm_set_charge() cannot set vbus to charge.
Clear pd events within PORT_RESET to get rid of non-applicable events.
Fixes: b17dd57118 ("staging: typec: tcpm: Improve role swap with non PD capable partners")
Cc: stable@vger.kernel.org
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240423202715.3375827-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6d73572206 upstream.
GUSB3PIPECTL.SUSPENDENABLE and GUSB2PHYCFG.SUSPHY should be cleared
during initialization. Suspend during initialization can result in
undefined behavior due to clock synchronization failure, which often
seen as core soft reset timeout.
The programming guide recommended these bits to be cleared during
initialization for DWC_usb3.0 version 1.94 and above (along with
DWC_usb31 and DWC_usb32). The current check in the driver does not
account if it's set by default setting from coreConsultant.
This is especially the case for DRD when switching mode to ensure the
phy clocks are available to change mode. Depending on the
platforms/design, some may be affected more than others. This is noted
in the DWC_usb3x programming guide under the above registers.
Let's just disable them during driver load and mode switching. Restore
them when the controller initialization completes.
Note that some platforms workaround this issue by disabling phy suspend
through "snps,dis_u3_susphy_quirk" and "snps,dis_u2_susphy_quirk" when
they should not need to.
Cc: stable@vger.kernel.org
Fixes: 9ba3aca8fe ("usb: dwc3: Disable phy suspend after power-on reset")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20da4e5a0c4678c9587d3da23f83bdd6d77353e9.1713394973.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 24729b307e upstream.
FFS based applications can utilize the aio_cancel() callback to dequeue
pending USB requests submitted to the UDC. There is a scenario where the
FFS application issues an AIO cancel call, while the UDC is handling a
soft disconnect. For a DWC3 based implementation, the callstack looks
like the following:
DWC3 Gadget FFS Application
dwc3_gadget_soft_disconnect() ...
--> dwc3_stop_active_transfers()
--> dwc3_gadget_giveback(-ESHUTDOWN)
--> ffs_epfile_async_io_complete() ffs_aio_cancel()
--> usb_ep_free_request() --> usb_ep_dequeue()
There is currently no locking implemented between the AIO completion
handler and AIO cancel, so the issue occurs if the completion routine is
running in parallel to an AIO cancel call coming from the FFS application.
As the completion call frees the USB request (io_data->req) the FFS
application is also referencing it for the usb_ep_dequeue() call. This can
lead to accessing a stale/hanging pointer.
commit b566d38857 ("usb: gadget: f_fs: use io_data->status consistently")
relocated the usb_ep_free_request() into ffs_epfile_async_io_complete().
However, in order to properly implement locking to mitigate this issue, the
spinlock can't be added to ffs_epfile_async_io_complete(), as
usb_ep_dequeue() (if successfully dequeuing a USB request) will call the
function driver's completion handler in the same context. Hence, leading
into a deadlock.
Fix this issue by moving the usb_ep_free_request() back to
ffs_user_copy_worker(), and ensuring that it explicitly sets io_data->req
to NULL after freeing it within the ffs->eps_lock. This resolves the race
condition above, as the ffs_aio_cancel() routine will not continue
attempting to dequeue a request that has already been freed, or the
ffs_user_copy_work() not freeing the USB request until the AIO cancel is
done referencing it.
This fix depends on
commit b566d38857 ("usb: gadget: f_fs: use io_data->status
consistently")
Fixes: 2e4c7553cd ("usb: gadget: f_fs: add aio support")
Cc: stable <stable@kernel.org> # b566d38857 ("usb: gadget: f_fs: use io_data->status consistently")
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240409014059.6740-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 650ae71c80 upstream.
This commit fixes uvc gadget support on 32-bit platforms.
Commit 0df28607c5 ("usb: gadget: uvc: Generalise helper functions for
reuse") introduced a helper function __uvcg_iter_item_entries() to aid
with parsing lists of items on configfs attributes stores. This function
is a generalization of another very similar function, which used a
stack-allocated temporary buffer of fixed size for each item in the list
and used the sizeof() operator to check for potential buffer overruns.
The new function was changed to allocate the now variably sized temp
buffer on heap, but wasn't properly updated to also check for max buffer
size using the computed size instead of sizeof() operator.
As a result, the maximum item size was 7 (plus null terminator) on
64-bit platforms, and 3 on 32-bit ones. While 7 is accidentally just
barely enough, 3 is definitely too small for some of UVC configfs
attributes. For example, dwFrameInteval, specified in 100ns units,
usually has 6-digit item values, e.g. 166666 for 60fps.
Cc: stable@vger.kernel.org
Fixes: 0df28607c5 ("usb: gadget: uvc: Generalise helper functions for reuse")
Signed-off-by: Ivan Avdeev <me@provod.works>
Link: https://lore.kernel.org/r/20240413150124.1062026-1-me@provod.works
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ec6ce7075e upstream.
The OS descriptors logic had the high/low byte of w_value inverted, causing
the extended properties to not be accessible for interface != 0.
>From the Microsoft documentation:
https://learn.microsoft.com/en-us/windows-hardware/drivers/usbcon/microsoft-os-1-0-descriptors-specification
OS_Desc_CompatID.doc (w_index = 0x4):
- wValue:
High Byte = InterfaceNumber. InterfaceNumber is set to the number of the
interface or function that is associated with the descriptor, typically
0x00. Because a device can have only one extended compat ID descriptor,
it should ignore InterfaceNumber, regardless of the value, and simply
return the descriptor.
Low Byte = 0. PageNumber is used to retrieve descriptors that are larger
than 64 KB. The header section is 16 bytes, so PageNumber is set to 0 for
this request.
We currently do not support >64KB compat ID descriptors, so verify that the
low byte is 0.
OS_Desc_Ext_Prop.doc (w_index = 0x5):
- wValue:
High byte = InterfaceNumber. The high byte of wValue is set to the number
of the interface or function that is associated with the descriptor.
Low byte = PageNumber. The low byte of wValue is used to retrieve
descriptors that are larger than 64 KB. The header section is 10 bytes, so
PageNumber is set to 0 for this request.
We also don't support >64KB extended properties, so verify that the low byte
is 0 and use the high byte for the interface number.
Fixes: 37a3a53342 ("usb: gadget: OS Feature Descriptors support")
Cc: stable <stable@kernel.org>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Link: https://lore.kernel.org/r/20240404100635.3215340-1-peter@korsgaard.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe81f35484 upstream.
Testing ohci functionality with qemu's pci-ohci emulation often results
in ohci interface stalls, resulting in hung task timeouts.
The problem is caused by lost interrupts between the emulation and the
Linux kernel code. Additional interrupts raised while the ohci interrupt
handler in Linux is running and before the handler clears the interrupt
status are not handled. The fix for a similar problem in ehci suggests
that the problem is likely caused by edge-triggered MSI interrupts. See
commit 0b60557230 ("usb: ehci: Prevent missed ehci interrupts with
edge-triggered MSI") for details.
Ensure that the ohci interrupt code handles all pending interrupts before
returning to solve the problem.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: David Laight <David.Laight@aculab.com>
Cc: stable@vger.kernel.org
Fixes: 306c54d0ed ("usb: hcd: Try MSI interrupts on PCI devices")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Link: https://lore.kernel.org/r/20240429154010.1507366-1-linux@roeck-us.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 808a8b9e0b upstream.
The completion notification for the final SET_NOTIFICATION_ENABLE
command during initialization can include a connector change
notification. However, at the time this completion notification is
processed, the ucsi struct is not ready to handle this notification.
As a result the notification is ignored and the controller
never sends an interrupt again.
Re-check CCI for a pending connector state change after
initialization is complete. Adjust the corresponding debug
message accordingly.
Fixes: 71a1fa0df2 ("usb: typec: ucsi: Store the notification mask")
Cc: stable@vger.kernel.org
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Link: https://lore.kernel.org/r/20240320073927.1641788-3-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3628e0383d upstream.
This reverts commit 07ed11afb6.
Stephen Rostedt reports:
"I went to run my tests on my VMs and the tests hung on boot up.
Unfortunately, the most I ever got out was:
[ 93.607888] Testing event system initcall: OK
[ 93.667730] Running tests on all trace events:
[ 93.669757] Testing all events: OK
[ 95.631064] ------------[ cut here ]------------
Timed out after 60 seconds"
and further debugging points to a possible circular locking dependency
between the console_owner locking and the worker pool locking.
Reverting the commit allows Steve's VM to boot to completion again.
[ This may obviously result in the "[TTM] Buffer eviction failed"
messages again, which was the reason for that original revert. But at
this point this seems preferable to a non-booting system... ]
Reported-and-bisected-by: Steven Rostedt <rostedt@goodmis.org>
Link: https://lore.kernel.org/all/20240502081641.457aa25f@gandalf.local.home/
Acked-by: Maxime Ripard <mripard@kernel.org>
Cc: Alex Constantino <dreaming.about.electric.sheep@gmail.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Timo Lindfors <timo.lindfors@iki.fi>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 38762a0763 upstream.
Ensure that packet_buffer_get respects the user_length provided. If
the length of the head packet exceeds the user_length, packet_buffer_get
will now return 0 to signify to the user that no data were read
and a larger buffer size is required. Helps prevent user space overflows.
Signed-off-by: Thanassis Avgerinos <thanassis.avgerinos@gmail.com>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ff09b6b8c upstream.
When compiling with gcc version 14.0.0 20231220 (experimental)
and W=1, I've noticed the following warning:
fs/btrfs/send.c: In function 'btrfs_ioctl_send':
fs/btrfs/send.c:8208:44: warning: 'kvcalloc' sizes specified with 'sizeof'
in the earlier argument and not in the later argument [-Wcalloc-transposed-args]
8208 | sctx->clone_roots = kvcalloc(sizeof(*sctx->clone_roots),
| ^
Since 'n' and 'size' arguments of 'kvcalloc()' are multiplied to
calculate the final size, their actual order doesn't affect the result
and so this is not a bug. But it's still worth to fix it.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d3a9331a65 upstream.
This reverts drm/amdgpu: fix ftrace event amdgpu_bo_move always move
on same heap. The basic problem here is that after the move the old
location is simply not available any more.
Some fixes were suggested, but essentially we should call the move
notification before actually moving things because only this way we have
the correct order for DMA-buf and VM move notifications as well.
Also rework the statistic handling so that we don't update the eviction
counter before the move.
v2: add missing NULL check
Signed-off-by: Christian König <christian.koenig@amd.com>
Fixes: 94aeb41173 ("drm/amdgpu: fix ftrace event amdgpu_bo_move always move on same heap")
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3171
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
CC: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9a35d205f4 ]
New request from KMD/VBIOS in order to support new UMA carveout
model. This fixes a null dereference from accessing
Ctx->dc_bios->integrated_info while it was NULL.
DAL parses through the BIOS and extracts the necessary
integrated_info but was missing a case for the new BIOS
version 2.3.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Gabe Teeger <gabe.teeger@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee0166b637 ]
If a line is requested with debounce, and that results in debouncing
in software, and the line is subsequently reconfigured to enable edge
detection then the allocation of the kfifo to contain edge events is
overlooked. This results in events being written to and read from an
uninitialised kfifo. Read events are returned to userspace.
Initialise the kfifo in the case where the software debounce is
already active.
Fixes: 65cff70464 ("gpiolib: cdev: support setting debounce")
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Link: https://lore.kernel.org/r/20240510065342.36191-1-warthog618@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9344e34e79 ]
Store the debounce period for a requested line locally, rather than in
the debounce_period_us field in the gpiolib struct gpio_desc.
Add a global tree of lines containing supplemental line information
to make the debounce period available to be reported by the
GPIO_V2_GET_LINEINFO_IOCTL and the line change notifier.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Stable-dep-of: ee0166b637 ("gpiolib: cdev: fix uninitialised kfifo")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 02f6b0e1ec ]
The use-after-free issue occurs as follows: when the GPIO chip device file
is being closed by invoking gpio_chrdev_release(), watched_lines is freed
by bitmap_free(), but the unregistration of lineinfo_changed_nb notifier
chain failed due to waiting write rwsem. Additionally, one of the GPIO
chip's lines is also in the release process and holds the notifier chain's
read rwsem. Consequently, a race condition leads to the use-after-free of
watched_lines.
Here is the typical stack when issue happened:
[free]
gpio_chrdev_release()
--> bitmap_free(cdev->watched_lines) <-- freed
--> blocking_notifier_chain_unregister()
--> down_write(&nh->rwsem) <-- waiting rwsem
--> __down_write_common()
--> rwsem_down_write_slowpath()
--> schedule_preempt_disabled()
--> schedule()
[use]
st54spi_gpio_dev_release()
--> gpio_free()
--> gpiod_free()
--> gpiod_free_commit()
--> gpiod_line_state_notify()
--> blocking_notifier_call_chain()
--> down_read(&nh->rwsem); <-- held rwsem
--> notifier_call_chain()
--> lineinfo_changed_notify()
--> test_bit(xxxx, cdev->watched_lines) <-- use after free
The side effect of the use-after-free issue is that a GPIO line event is
being generated for userspace where it shouldn't. However, since the chrdev
is being closed, userspace won't have the chance to read that event anyway.
To fix the issue, call the bitmap_free() function after the unregistration
of lineinfo_changed_nb notifier chain.
Fixes: 51c1064e82 ("gpiolib: add new ioctl() for monitoring changes in line info")
Signed-off-by: Zhongqiu Han <quic_zhonhan@quicinc.com>
Link: https://lore.kernel.org/r/20240505141156.2944912-1-quic_zhonhan@quicinc.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f39bf3cf08 ]
As of commit de5c9bf40c ("net: phylink: require supported_interfaces to
be filled")
Marvell 88e6320/21 switches fail to be probed:
...
mv88e6085 30be0000.ethernet-1:00: phylink: error: empty supported_interfaces
error creating PHYLINK: -22
...
The problem stems from the use of mv88e6185_phylink_get_caps() to get
the device capabilities.
Since there are serdes only ports 0/1 included, create a new dedicated
phylink_get_caps for the 6320 and 6321 to properly support their
set of capabilities.
Fixes: de5c9bf40c ("net: phylink: require supported_interfaces to be filled")
Signed-off-by: Steffen Bätz <steffen@innosonix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20240508072944.54880-2-steffen@innosonix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 35d92abfba ]
The devlink reload process will access the hardware resources,
but the register operation is done before the hardware is initialized.
So, processing the devlink reload during initialization may lead to kernel
crash.
This patch fixes this by registering the devlink after
hardware initialization.
Fixes: cd6242991d ("net: hns3: add support for registering devlink for VF")
Fixes: 93305b77ff ("net: hns3: fix kernel crash when devlink reload during pf initialization")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f5db7a3b65 ]
According to hardware limitation, for device support modify
VLAN filter state but not support bypass port VLAN filter,
it should always disable the port VLAN filter. but the driver
enables port VLAN filter when initializing, if there is no
VLAN(except VLAN 0) id added, the driver will disable it
in service task. In most time, it works fine. But there is
a time window before the service task shceduled and net device
being registered. So if user adds VLAN at this time, the driver
will not update the VLAN filter state, and the port VLAN filter
remains enabled.
To fix the problem, if support modify VLAN filter state but not
support bypass port VLAN filter, set the port vlan filter to "off".
Fixes: 184cd221a8 ("net: hns3: disable port VLAN filter when support function level VLAN filter control")
Fixes: 2ba306627f ("net: hns3: add support for modify VLAN filter state")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 094c281228 ]
There is a memory barrier in followed case. When set the port down,
hclgevf_set_timmer will set DOWN in state. Meanwhile, the service task has
different behaviour based on whether the state is DOWN. Thus, to make sure
service task see DOWN, use smp_mb__after_atomic after calling set_bit().
CPU0 CPU1
========================== ===================================
hclgevf_set_timer_task() hclgevf_periodic_service_task()
set_bit(DOWN,state) test_bit(DOWN,state)
pf also has this issue.
Fixes: ff200099d2 ("net: hns3: remove unnecessary work in hclgevf_main")
Fixes: 1c6dfe6fc6 ("net: hns3: remove mailbox and reset work in hclge_main")
Signed-off-by: Peiyang Wang <wangpeiyang1@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 950aa42399 ]
During the PF initialization process, hclge_update_port_info may return an
error code for some reason. At this point, the ptp initialization has been
completed. To void memory leaks, the resources that are applied by ptp
should be released. Therefore, when hclge_update_port_info returns an error
code, hclge_ptp_uninit is called to release the corresponding resources.
Fixes: eaf83ae59e ("net: hns3: add querying fec ability from firmware")
Signed-off-by: Peiyang Wang <wangpeiyang1@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6639a7b953 ]
It provides nodemask_t to describe the numa node mask in kernel. To
improve transportability, change the type of numa_node_mask as nodemask_t.
Fixes: 38caee9d3e ("net: hns3: Add support of the HNAE3 framework")
Signed-off-by: Peiyang Wang <wangpeiyang1@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 669554c512 ]
Currently, the driver didn't return when receive a unknown
mailbox message, and continue checking whether need to
generate a response. It's unnecessary and may be incorrect.
Fixes: bb5790b71b ("net: hns3: refactor mailbox response scheme between PF and VF")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05eb60e964 ]
When a reset occurring, it's supposed to recover user's configuration.
Currently, the port info(speed, duplex and autoneg) is stored in hclge_mac
and will be scheduled updated. Consider the case that reset was happened
consecutively. During the first reset, the port info is configured with
a temporary value cause the PHY is reset and looking for best link config.
Second reset start and use pervious configuration which is not the user's.
The specific process is as follows:
+------+ +----+ +----+
| USER | | PF | | HW |
+---+--+ +-+--+ +-+--+
| ethtool --reset | |
+------------------->| reset command |
| ethtool --reset +-------------------->|
+------------------->| +---+
| +---+ | |
| | |reset currently | | HW RESET
| | |and wait to do | |
| |<--+ | |
| | send pervious cfg |<--+
| | (1000M FULL AN_ON) |
| +-------------------->|
| | read cfg(time task) |
| | (10M HALF AN_OFF) +---+
| |<--------------------+ | cfg take effect
| | reset command |<--+
| +-------------------->|
| | +---+
| | send pervious cfg | | HW RESET
| | (10M HALF AN_OFF) |<--+
| +-------------------->|
| | read cfg(time task) |
| | (10M HALF AN_OFF) +---+
| |<--------------------+ | cfg take effect
| | | |
| | read cfg(time task) |<--+
| | (10M HALF AN_OFF) |
| |<--------------------+
| | |
v v v
To avoid aboved situation, this patch introduced req_speed, req_duplex,
req_autoneg to store user's configuration and it only be used after
hardware reset and to recover user's configuration
Fixes: f5f2b3e4dc ("net: hns3: add support for imp-controlled PHYs")
Signed-off-by: Peiyang Wang <wangpeiyang1@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d289ab65b8 ]
disable_ipv6 is read locklessly, add appropriate READ_ONCE()
and WRITE_ONCE() annotations.
v2: do not preload net before rtnl_trylock() in
addrconf_disable_ipv6() (Jiri)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 4db783d68b ("ipv6: prevent NULL dereference in ip6_output()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4893b8b3ef ]
Up till now the code to start HSR announce timer, which triggers sending
supervisory frames, was assuming that hsr_netdev_notify() would be called
at least twice for hsrX interface. This was required to have different
values for old and current values of network device's operstate.
This is problematic for a case where hsrX interface is already in the
operational state when hsr_netdev_notify() is called, so timer is not
configured to trigger and as a result the hsrX is not sending supervisory
frames to HSR ring.
This error has been discovered when hsr_ping.sh script was run. To be
more specific - for the hsr1 and hsr2 the hsr_netdev_notify() was
called at least twice with different IF_OPER_{LOWERDOWN|DOWN|UP} states
assigned in hsr_check_carrier_and_operstate(hsr). As a result there was
no issue with sending supervisory frames.
However, with hsr3, the notify function was called only once with
operstate set to IF_OPER_UP and timer responsible for triggering
supervisory frames was not fired.
The solution is to use netif_oper_up() and netif_running() helper
functions to assess if network hsrX device is up.
Only then, when the timer is not already pending, it is started.
Otherwise it is deactivated.
Fixes: f421436a59 ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240507111214.3519800-1-lukma@denx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 004d138364 ]
operstate_show() can omit dev_base_lock acquisition only
to read dev->operstate.
Annotate accesses to dev->operstate.
Writers still acquire dev_base_lock for mutual exclusion.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 4893b8b3ef ("hsr: Simplify code for announcing HSR nodes timer setup")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc349b0771 ]
Several clocks as well as both sgmiisys phandles were added by mistake
to the Ethernet bindings for MT7988. Also, the total number of clocks
didn't match with the actual number of items listed.
This happened because the vendor driver which served as a reference uses
a high number of syscon phandles to access various parts of the SoC
which wasn't acceptable upstream. Hence several parts which have never
previously been supported (such SerDes PHY and USXGMII PCS) are going to
be implemented by separate drivers. As a result the device tree will
look much more sane.
Quickly align the bindings with the upcoming reality of the drivers
actually adding support for the remaining Ethernet-related features of
the MT7988 SoC.
Fixes: c94a9aabec ("dt-bindings: net: mediatek,net: add mt7988-eth binding")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/1569290b21cc787a424469ed74456a7e976b102d.1715084326.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 012b720691 ]
Only generate one ACK packet for all the subpackets in a jumbo packet. If
we would like to generate more than one ACK, we prioritise them base on
their reason code, in the order, highest first:
OutOfSeq > NoSpace > ExceedsWin > Duplicate > Requested > Delay > Idle
For the first four, we reference the lowest offending subpacket; for the
last three, the highest.
This reduces the number of ACKs we end up transmitting to one per UDP
packet transmitted to reduce network loading and packet parsing.
Fixes: 5d7edbc923 ("rxrpc: Get rid of the Rx ring")
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Reviewed-by: Jeffrey Altman <jaltman@auristor.com <mailto:jaltman@auristor.com>>
Link: https://lore.kernel.org/r/20240503150749.1001323-3-dhowells@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ba4e103848 ]
Make the following fixes to the congestion control algorithm:
(1) Don't vary the cwnd starting value by the size of RXRPC_TX_SMSS since
that's currently held constant - set to the size of a jumbo subpacket
payload so that we can create jumbo packets on the fly. The current
code invariably picks 3 as the starting value.
Further, the starting cwnd needs to be an even number because we ack
every other packet, so set it to 4.
(2) Don't cut ssthresh when we see an ACK come from the peer with a
receive window (rwind) less than ssthresh. ssthresh keeps track of
characteristics of the connection whereas rwind may be reduced by the
peer for any reason - and may be reduced to 0.
Fixes: 1fc4fa2ac9 ("rxrpc: Fix congestion management")
Fixes: 0851115090 ("rxrpc: Reduce ssthresh to peer's receive window")
Signed-off-by: David Howells <dhowells@redhat.com>
Suggested-by: Simon Wilkinson <sxw@auristor.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Reviewed-by: Jeffrey Altman <jaltman@auristor.com <mailto:jaltman@auristor.com>>
Link: https://lore.kernel.org/r/20240503150749.1001323-2-dhowells@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a169c267e ]
When creating the topology for the test, three veth pairs are created in
the initial network namespace before being moved to one of the network
namespaces created by the test.
On systems where systemd-udev uses MACAddressPolicy=persistent (default
since systemd version 242), this will result in some net devices having
the same MAC address since they were created with the same name in the
initial network namespace. In turn, this leads to arping / ndisc6
failing since packets are dropped by the bridge's loopback filter.
Fix by creating each net device in the correct network namespace instead
of moving it there from the initial network namespace.
Reported-by: Jakub Kicinski <kuba@kernel.org>
Closes: https://lore.kernel.org/netdev/20240426074015.251854d4@kernel.org/
Fixes: 7648ac72dc ("selftests: net: Add bridge neighbor suppression test")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/20240507113033.1732534-1-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e13d3a9c2 ]
As it was done in commit fc1092f515 ("ipv4: Fix uninit-value access in
__ip_make_skb()") for IPv4, check FLOWI_FLAG_KNOWN_NH on fl6->flowi6_flags
instead of testing HDRINCL on the socket to avoid a race condition which
causes uninit-value access.
Fixes: ea30388bae ("ipv6: Fix an uninit variable access bug in __ip6_make_skb()")
Signed-off-by: Shigeru Yoshida <syoshida@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86b29d830a ]
The change from skb_copy to pskb_copy unfortunately changed the data
copying to omit the ethernet header, since it was pulled before reaching
this point. Fix this by calling __skb_push/pull around pskb_copy.
Fixes: 59c878cbcd ("net: bridge: fix multicast-to-unicast with fraglist GSO")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d02abd57e7 ]
Through hidraw, userspace can cause a status report to be sent
from the device. The parsing in ccp_raw_event() may happen in
parallel to a send_usb_cmd() call (which resets the completion
for tracking the report) if it's running on a different CPU where
bottom half interrupts are not disabled.
Add a spinlock around the complete_all() in ccp_raw_event() and
reinit_completion() in send_usb_cmd() to prevent race issues.
Fixes: 40c3a44542 ("hwmon: add Corsair Commander Pro driver")
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Acked-by: Marius Zachmann <mail@mariuszachmann.de>
Link: https://lore.kernel.org/r/20240504092504.24158-4-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e0cd85dc66 ]
Introduce cmd_buffer, a separate buffer for storing only
the command that is sent to the device. Before this separation,
the existing buffer was shared for both the command and the
report received in ccp_raw_event(), which was copied into it.
However, because of hidraw, the raw event parsing may be triggered
in the middle of sending a command, resulting in outputting gibberish
to the device. Using a separate buffer resolves this.
Fixes: 40c3a44542 ("hwmon: add Corsair Commander Pro driver")
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Acked-by: Marius Zachmann <mail@mariuszachmann.de>
Link: https://lore.kernel.org/r/20240504092504.24158-2-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1aec77b2bb ]
Each attribute inside a nested IFLA_VF_VLAN_LIST is assumed to be a
struct ifla_vf_vlan_info so the size of such attribute needs to be at least
of sizeof(struct ifla_vf_vlan_info) which is 14 bytes.
The current size validation in do_setvfinfo is against NLA_HDRLEN (4 bytes)
which is less than sizeof(struct ifla_vf_vlan_info) so this validation
is not enough and a too small attribute might be cast to a
struct ifla_vf_vlan_info, this might result in an out of bands
read access when accessing the saved (casted) entry in ivvl.
Fixes: 79aab093a0 ("net: Update API for VF vlan protocol 802.1ad support")
Signed-off-by: Roded Zats <rzats@paloaltonetworks.com>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Link: https://lore.kernel.org/r/20240502155751.75705-1-rzats@paloaltonetworks.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e0863634bf ]
Currently the driver uses local_bh_disable()/local_bh_enable() in its
IRQ handler to avoid triggering net_rx_action() softirq on exit from
netif_rx(). The net_rx_action() could trigger this driver .start_xmit
callback, which is protected by the same lock as the IRQ handler, so
calling the .start_xmit from netif_rx() from the IRQ handler critical
section protected by the lock could lead to an attempt to claim the
already claimed lock, and a hang.
The local_bh_disable()/local_bh_enable() approach works only in case
the IRQ handler is protected by a spinlock, but does not work if the
IRQ handler is protected by mutex, i.e. this works for KS8851 with
Parallel bus interface, but not for KS8851 with SPI bus interface.
Remove the BH manipulation and instead of calling netif_rx() inside
the IRQ handler code protected by the lock, queue all the received
SKBs in the IRQ handler into a queue first, and once the IRQ handler
exits the critical section protected by the lock, dequeue all the
queued SKBs and push them all into netif_rx(). At this point, it is
safe to trigger the net_rx_action() softirq, since the netif_rx()
call is outside of the lock that protects the IRQ handler.
Fixes: be0384bf59 ("net: ks8851: Handle softirqs at the end of IRQ thread to fix hang")
Tested-by: Ronald Wahl <ronald.wahl@raritan.com> # KS8851 SPI
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240502183436.117117-1-marex@denx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d2706004a1 ]
Fix potential null-ptr-deref in hci_le_big_sync_established_evt().
Fixes: f777d88278 (Bluetooth: ISO: Notify user space about failed bis connections)
Signed-off-by: Sungwoo Kim <iam@sung-woo.kim>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 10f9f426ac ]
Tying the msft->data lifetime to hdev by freeing it in
hci_release_dev() to fix the following case:
[use]
msft_do_close()
msft = hdev->msft_data;
if (!msft) ...(1) <- passed.
return;
mutex_lock(&msft->filter_lock); ...(4) <- used after freed.
[free]
msft_unregister()
msft = hdev->msft_data;
hdev->msft_data = NULL; ...(2)
kfree(msft); ...(3) <- msft is freed.
==================================================================
BUG: KASAN: slab-use-after-free in __mutex_lock_common
kernel/locking/mutex.c:587 [inline]
BUG: KASAN: slab-use-after-free in __mutex_lock+0x8f/0xc30
kernel/locking/mutex.c:752
Read of size 8 at addr ffff888106cbbca8 by task kworker/u5:2/309
Fixes: bf6a4e30ff ("Bluetooth: disable advertisement filters during suspend")
Signed-off-by: Sungwoo Kim <iam@sung-woo.kim>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4238686f9 ]
We found below OOB crash:
[ 33.452494] ==================================================================
[ 33.453513] BUG: KASAN: stack-out-of-bounds in refresh_cpu_vm_stats.constprop.0+0xcc/0x2ec
[ 33.454660] Write of size 164 at addr c1d03d30 by task swapper/0/0
[ 33.455515]
[ 33.455767] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G O 6.1.25-mainline #1
[ 33.456880] Hardware name: Generic DT based system
[ 33.457555] unwind_backtrace from show_stack+0x18/0x1c
[ 33.458326] show_stack from dump_stack_lvl+0x40/0x4c
[ 33.459072] dump_stack_lvl from print_report+0x158/0x4a4
[ 33.459863] print_report from kasan_report+0x9c/0x148
[ 33.460616] kasan_report from kasan_check_range+0x94/0x1a0
[ 33.461424] kasan_check_range from memset+0x20/0x3c
[ 33.462157] memset from refresh_cpu_vm_stats.constprop.0+0xcc/0x2ec
[ 33.463064] refresh_cpu_vm_stats.constprop.0 from tick_nohz_idle_stop_tick+0x180/0x53c
[ 33.464181] tick_nohz_idle_stop_tick from do_idle+0x264/0x354
[ 33.465029] do_idle from cpu_startup_entry+0x20/0x24
[ 33.465769] cpu_startup_entry from rest_init+0xf0/0xf4
[ 33.466528] rest_init from arch_post_acpi_subsys_init+0x0/0x18
[ 33.467397]
[ 33.467644] The buggy address belongs to stack of task swapper/0/0
[ 33.468493] and is located at offset 112 in frame:
[ 33.469172] refresh_cpu_vm_stats.constprop.0+0x0/0x2ec
[ 33.469917]
[ 33.470165] This frame has 2 objects:
[ 33.470696] [32, 76) 'global_zone_diff'
[ 33.470729] [112, 276) 'global_node_diff'
[ 33.471294]
[ 33.472095] The buggy address belongs to the physical page:
[ 33.472862] page:3cd72da8 refcount:1 mapcount:0 mapping:00000000 index:0x0 pfn:0x41d03
[ 33.473944] flags: 0x1000(reserved|zone=0)
[ 33.474565] raw: 00001000 ed741470 ed741470 00000000 00000000 00000000 ffffffff 00000001
[ 33.475656] raw: 00000000
[ 33.476050] page dumped because: kasan: bad access detected
[ 33.476816]
[ 33.477061] Memory state around the buggy address:
[ 33.477732] c1d03c00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 33.478630] c1d03c80: 00 00 00 00 00 00 00 00 f1 f1 f1 f1 00 00 00 00
[ 33.479526] >c1d03d00: 00 04 f2 f2 f2 f2 00 00 00 00 00 00 f1 f1 f1 f1
[ 33.480415] ^
[ 33.481195] c1d03d80: 00 00 00 00 00 00 00 00 00 00 04 f3 f3 f3 f3 f3
[ 33.482088] c1d03e00: f3 f3 f3 f3 00 00 00 00 00 00 00 00 00 00 00 00
[ 33.482978] ==================================================================
We find the root cause of this OOB is that arm does not clear stale stack
poison in the case of cpuidle.
This patch refer to arch/arm64/kernel/sleep.S to resolve this issue.
From cited commit [1] that explain the problem
Functions which the compiler has instrumented for KASAN place poison on
the stack shadow upon entry and remove this poison prior to returning.
In the case of cpuidle, CPUs exit the kernel a number of levels deep in
C code. Any instrumented functions on this critical path will leave
portions of the stack shadow poisoned.
If CPUs lose context and return to the kernel via a cold path, we
restore a prior context saved in __cpu_suspend_enter are forgotten, and
we never remove the poison they placed in the stack shadow area by
functions calls between this and the actual exit of the kernel.
Thus, (depending on stackframe layout) subsequent calls to instrumented
functions may hit this stale poison, resulting in (spurious) KASAN
splats to the console.
To avoid this, clear any stale poison from the idle thread for a CPU
prior to bringing a CPU online.
From cited commit [2]
Extend to check for CONFIG_KASAN_STACK
[1] commit 0d97e6d802 ("arm64: kasan: clear stale stack poison")
[2] commit d56a9ef84b ("kasan, arm64: unpoison stack only with CONFIG_KASAN_STACK")
Signed-off-by: Boy Wu <boy.wu@mediatek.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Fixes: 5615f69bc2 ("ARM: 9016/2: Initialize the mapping of KASan shadow memory")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58fbfecab9 ]
The software GRO path for esp transport mode uses skb_mac_header_rebuild
prior to re-injecting the packet via the xfrm_napi_dev. This only
copies skb->mac_len bytes of header which may not be sufficient if the
packet contains 802.1Q tags or other VLAN tags. Worse copying only the
initial header will leave a packet marked as being VLAN tagged but
without the corresponding tag leading to mangling when it is later
untagged.
The VLAN tags are important when receiving the decrypted esp transport
mode packet after GRO processing to ensure it is received on the correct
interface.
Therefore record the full mac header length in xfrm*_transport_input for
later use in corresponding xfrm*_transport_finish to copy the entire mac
header when rebuilding the mac header for GRO. The skb->data pointer is
left pointing skb->mac_header bytes after the start of the mac header as
is expected by the network stack and network and transport header
offsets reset to this location.
Fixes: 7785bba299 ("esp: Add a software GRO codepath")
Signed-off-by: Paul Davey <paul.davey@alliedtelesis.co.nz>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa23317d02 ]
simple_recursive_removal() drops the pinning references to all positives
in subtree. For the cases when its argument has been kept alive by
the pinning alone that's exactly the right thing to do, but here
the argument comes from dcache lookup, that needs to be balanced by
explicit dput().
Fixes: e41d237818 "qib_fs: switch to simple_recursive_removal()"
Fucked-up-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 01bc4fda9e ]
In iocg_pay_debt(), warn is triggered if 'active_list' is empty, which
is intended to confirm iocg is active when it has debt. However, warn
can be triggered during a blkcg or disk removal, if iocg_waitq_timer_fn()
is run at that time:
WARNING: CPU: 0 PID: 2344971 at block/blk-iocost.c:1402 iocg_pay_debt+0x14c/0x190
Call trace:
iocg_pay_debt+0x14c/0x190
iocg_kick_waitq+0x438/0x4c0
iocg_waitq_timer_fn+0xd8/0x130
__run_hrtimer+0x144/0x45c
__hrtimer_run_queues+0x16c/0x244
hrtimer_interrupt+0x2cc/0x7b0
The warn in this situation is meaningless. Since this iocg is being
removed, the state of the 'active_list' is irrelevant, and 'waitq_timer'
is canceled after removing 'active_list' in ioc_pd_free(), which ensures
iocg is freed after iocg_waitq_timer_fn() returns.
Therefore, add the check if iocg was already offlined to avoid warn
when removing a blkcg or disk.
Signed-off-by: Li Nan <linan122@huawei.com>
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/20240419093257.3004211-1-linan666@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf52d7f9b2 ]
I didn't pay close enough attention the last time I tried to fix this
problem - while we currently do correctly take care to make sure we don't
probe a connected eDP port more then once, we don't do the same thing for
eDP ports we found to be disconnected.
So, fix this and make sure we only ever probe eDP ports once and then leave
them at that connector state forever (since without HPD, it's not going to
change on its own anyway). This should get rid of the last few GSP errors
getting spit out during runtime suspend and resume on some machines, as we
tried to reprobe eDP ports in response to ACPI hotplug probe events.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240404233736.7946-3-lyude@redhat.com
(cherry picked from commit fe6660b661)
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11baa36d31 ]
Add MODULE_DEVICE_TABLE(), so the module could be properly autoloaded
based on the alias from of_device_id table.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f63af7511 ]
We don't need to hold the prepare_lock when dropping a ref on a struct
clk_core. The release function is only freeing memory and any code with
a pointer reference has already unlinked anything pointing to the
clk_core. This reduces the holding area of the prepare_lock a bit.
Note that we also don't call free_clk() with the prepare_lock held.
There isn't any reason to do that.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20240325184204.745706-3-sboyd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ace0ebe5c9 ]
The GPIO library expects the drivers to return -ENOTSUPP in some
cases and not using analogue POSIX code. Make the driver to follow
this.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6963092601 ]
The chacha-p10-crypto module provides optimised chacha routines for
Power10. It also selects CRYPTO_ARCH_HAVE_LIB_CHACHA which says it
provides chacha_crypt_arch() to generic code.
Notably the module needs to provide chacha_crypt_arch() regardless of
whether it is loaded on Power10 or an older CPU.
The implementation of chacha_crypt_arch() already has a fallback to
chacha_crypt_generic(), however the module as a whole fails to load on
pre-Power10, because of the use of module_cpu_feature_match().
This breaks for example loading wireguard:
jostaberry-1:~ # modprobe -v wireguard
insmod /lib/modules/6.8.0-lp155.8.g7e0e887-default/kernel/arch/powerpc/crypto/chacha-p10-crypto.ko.zst
modprobe: ERROR: could not insert 'wireguard': No such device
Fix it by removing module_cpu_feature_match(), and instead check the
CPU feature manually. If the CPU feature is not found, the module
still loads successfully, but doesn't register the Power10 specific
algorithms. That allows chacha_crypt_generic() to remain available for
use, fixing the problem.
[root@fedora ~]# modprobe -v wireguard
insmod /lib/modules/6.8.0-00001-g786a790c4d79/kernel/net/ipv4/udp_tunnel.ko
insmod /lib/modules/6.8.0-00001-g786a790c4d79/kernel/net/ipv6/ip6_udp_tunnel.ko
insmod /lib/modules/6.8.0-00001-g786a790c4d79/kernel/lib/crypto/libchacha.ko
insmod /lib/modules/6.8.0-00001-g786a790c4d79/kernel/arch/powerpc/crypto/chacha-p10-crypto.ko
insmod /lib/modules/6.8.0-00001-g786a790c4d79/kernel/lib/crypto/libchacha20poly1305.ko
insmod /lib/modules/6.8.0-00001-g786a790c4d79/kernel/drivers/net/wireguard/wireguard.ko
[ 18.910452][ T721] wireguard: allowedips self-tests: pass
[ 18.914999][ T721] wireguard: nonce counter self-tests: pass
[ 19.029066][ T721] wireguard: ratelimiter self-tests: pass
[ 19.029257][ T721] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[ 19.029361][ T721] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
Reported-by: Michal Suchánek <msuchanek@suse.de>
Closes: https://lore.kernel.org/all/20240315122005.GG20665@kitsune.suse.cz/
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20240328130200.3041687-1-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a84602297 ]
9p is a remote network protocol, and it doesn't support asynchronous
notifications from the server. Ensure that we don't hand out any leases
since we can't guarantee they'll be broken when a file's contents
change.
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Eric Van Hensbergen <ericvh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e5d208cc9 ]
I'm not sure why this check was ever here. After updating to 6.6 I
suddenly found caching had been turned on by default and neither
cache=none nor the new directio would turn it off. After walking through
the new code very manually I realized that it's because the caching has
to be, in effect, turned off explicitly by setting P9L_DIRECT and
whenever a file has a flag, in my case QTAPPEND, it doesn't get set.
Setting aside QTDIR which seems to ignore the new fid->mode entirely,
the rest of these either should be subject to the same cache rules as
every other QTFILE or perhaps very explicitly not cached in the case of
QTAUTH.
Signed-off-by: Joakim Sindholt <opensource@zhasha.com>
Signed-off-by: Eric Van Hensbergen <ericvh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87de39e705 ]
This one hits both 9P2000 and .u as it appears v9fs has never translated
the O_TRUNC flag.
Signed-off-by: Joakim Sindholt <opensource@zhasha.com>
Signed-off-by: Eric Van Hensbergen <ericvh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd25e15e57 ]
Garbage in plain 9P2000's perm bits is allowed through, which causes it
to be able to set (among others) the suid bit. This was presumably not
the intent since the unix extended bits are handled explicitly and
conditionally on .u.
Signed-off-by: Joakim Sindholt <opensource@zhasha.com>
Signed-off-by: Eric Van Hensbergen <ericvh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 35f834265e ]
There are various use cases that are becoming more common in which password
changes are scheduled on a server(s) periodically but the clients connected
to this server need to stay connected (even in the face of brief network
reconnects) due to mounts which can not be easily unmounted and mounted at
will, and servers that do password rotation do not always have the ability
to tell the clients exactly when to the new password will be effective,
so add support for an alt password ("password2=") on mount (and also
remount) so that we can anticipate the upcoming change to the server
without risking breaking existing mounts.
An alternative would have been to use the kernel keyring for this but the
processes doing the reconnect do not have access to the keyring but do
have access to the ses structure.
Reviewed-by: Bharath SM <bharathsm@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 30d18df656 ]
In CoCo VMs it is possible for the untrusted host to cause
set_memory_encrypted() or set_memory_decrypted() to fail such that an
error is returned and the resulting memory is shared. Callers need to
take care to handle these errors to avoid returning decrypted (shared)
memory to the page allocator, which could lead to functional or security
issues.
The VMBus ring buffer code could free decrypted/shared pages if
set_memory_decrypted() fails. Check the decrypted field in the struct
vmbus_gpadl for the ring buffers to decide whether to free the memory.
Signed-off-by: Michael Kelley <mhklinux@outlook.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Link: https://lore.kernel.org/r/20240311161558.1310-6-mhklinux@outlook.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <20240311161558.1310-6-mhklinux@outlook.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 211f514ebf ]
In CoCo VMs it is possible for the untrusted host to cause
set_memory_encrypted() or set_memory_decrypted() to fail such that an
error is returned and the resulting memory is shared. Callers need to
take care to handle these errors to avoid returning decrypted (shared)
memory to the page allocator, which could lead to functional or security
issues.
In order to make sure callers of vmbus_establish_gpadl() and
vmbus_teardown_gpadl() don't return decrypted/shared pages to
allocators, add a field in struct vmbus_gpadl to keep track of the
decryption status of the buffers. This will allow the callers to
know if they should free or leak the pages.
Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Signed-off-by: Michael Kelley <mhklinux@outlook.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Link: https://lore.kernel.org/r/20240311161558.1310-3-mhklinux@outlook.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <20240311161558.1310-3-mhklinux@outlook.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0763613621 ]
The struct adjtimex freq field takes a signed value who's units are in
shifted (<<16) parts-per-million.
Unfortunately for negative adjustments, the straightforward use of:
freq = ppm << 16 trips undefined behavior warnings with clang:
valid-adjtimex.c:66:6: warning: shifting a negative signed value is undefined [-Wshift-negative-value]
-499<<16,
~~~~^
valid-adjtimex.c:67:6: warning: shifting a negative signed value is undefined [-Wshift-negative-value]
-450<<16,
~~~~^
..
Fix it by using a multiply by (1 << 16) instead of shifting negative values
in the valid-adjtimex test case. Align the values for better readability.
Reported-by: Lee Jones <joneslee@google.com>
Reported-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Signed-off-by: John Stultz <jstultz@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Link: https://lore.kernel.org/r/20240409202222.2830476-1-jstultz@google.com
Link: https://lore.kernel.org/lkml/0c6d4f0d-2064-4444-986b-1d1ed782135f@collabora.com/
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d06af584be ]
If there are more than one device doing reset in parallel, the first
device will call kfd_suspend_all_processes() to evict all processes
on all devices, this call takes time to finish. other device will
start reset and recover without waiting. if the process has not been
evicted before doing recover, it will be restored, then caused page
fault.
Signed-off-by: Zhigang Luo <Zhigang.Luo@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 60add818ab ]
Running turbostat on a 16 socket HPE Scale-up Compute 3200 (SapphireRapids) fails with:
turbostat: /sys/devices/system/cpu/intel_uncore_frequency/package_010_die_00/current_freq_khz: open failed: No such file or directory
We observe the sysfs uncore frequency directories named:
...
package_09_die_00/
package_10_die_00/
package_11_die_00/
...
package_15_die_00/
The culprit is an incorrect sprintf format string "package_0%d_die_0%d" used
with each instance of reading uncore frequency files. uncore-frequency-common.c
creates the sysfs directory with the format "package_%02d_die_%02d". Once the
package value reaches double digits, the formats diverge.
Change each instance of "package_0%d_die_0%d" to "package_%02d_die_%02d".
[lenb: deleted the probe part of this patch, as it was already fixed]
Signed-off-by: Justin Ernst <justin.ernst@hpe.com>
Reviewed-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4370b673cc ]
thread_info.syscall is used by syscall_get_nr to supply syscall nr
over a thread stack frame.
Previously, thread_info.syscall is only saved at syscall_trace_enter
when syscall tracing is enabled. However rest of the kernel code do
expect syscall_get_nr to be available without syscall tracing. The
previous design breaks collect_syscall.
Move saving process to syscall entry to fix it.
Reported-by: Xi Ruoyao <xry111@xry111.site>
Link: https://github.com/util-linux/util-linux/issues/2867
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit beaa51b360 ]
UBSAN catches undefined behavior in blk-iocost, where sometimes
iocg->delay is shifted right by a number that is too large,
resulting in undefined behavior on some architectures.
[ 186.556576] ------------[ cut here ]------------
UBSAN: shift-out-of-bounds in block/blk-iocost.c:1366:23
shift exponent 64 is too large for 64-bit type 'u64' (aka 'unsigned long long')
CPU: 16 PID: 0 Comm: swapper/16 Tainted: G S E N 6.9.0-0_fbk700_debug_rc2_kbuilder_0_gc85af715cac0 #1
Hardware name: Quanta Twin Lakes MP/Twin Lakes Passive MP, BIOS F09_3A23 12/08/2020
Call Trace:
<IRQ>
dump_stack_lvl+0x8f/0xe0
__ubsan_handle_shift_out_of_bounds+0x22c/0x280
iocg_kick_delay+0x30b/0x310
ioc_timer_fn+0x2fb/0x1f80
__run_timer_base+0x1b6/0x250
...
Avoid that undefined behavior by simply taking the
"delay = 0" branch if the shift is too large.
I am not sure what the symptoms of an undefined value
delay will be, but I suspect it could be more than a
little annoying to debug.
Signed-off-by: Rik van Riel <riel@surriel.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Josef Bacik <josef@toxicpanda.com>
Cc: Jens Axboe <axboe@kernel.dk>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/20240404123253.0f58010f@imladris.surriel.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 97a54ef596 ]
If the systemd-modules service loads the target module, the credentials of
that userspace process will be used to validate the access to the target db
directory. SELinux will prevent it, reporting an error like the following:
kernel: audit: type=1400 audit(1676301082.205:4): avc: denied { read }
for pid=1020 comm="systemd-modules" name="target" dev="dm-3"
ino=4657583 scontext=system_u:system_r:systemd_modules_load_t:s0
tcontext=system_u:object_r:targetd_etc_rw_t:s0 tclass=dir permissive=0
Fix the error by using the kernel credentials to access the db directory
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Link: https://lore.kernel.org/r/20240215143944.847184-2-mlombard@redhat.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e68de0bb0 ]
It is possible to clear a root's IN_TRANS tag from the radix tree, but
not clear its PERTRANS, if there is some error in between. Eliminate
that possibility by moving the free up to where we clear the tag.
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Boris Burkov <boris@bur.io>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c6f0c5ecc ]
Currently, this call site in btrfs_clear_delalloc_extent() only converts
the reservation. We are marking it not delalloc, so I don't think it
makes sense to keep the rsv around. This is a path where we are not
sure to join a transaction, so it leads to incorrect free-ing during
umount.
Helps with the pass rate of generic/269 and generic/475.
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Boris Burkov <boris@bur.io>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6fe938317 ]
Previously a failed read of /dev/cpu_dma_latency erroneously complained
turbostat: capget(CAP_SYS_ADMIN) failed, try "# setcap cap_sys_admin=ep ./turbostat
This went unnoticed because this file is typically visible to root,
and turbostat was typically run as root.
Going forward, when a non-root user can run turbostat...
Complain about failed read access to this file only if --debug is used.
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b13410b52 ]
The code calculates Bzy_MHz by multiplying TSC_delta * APERF_delta/MPERF_delta
The man page erroneously showed that TSC_delta was divided.
Signed-off-by: Peng Liu <liupeng17@lenovo.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ac1d14d05 ]
When running turbostat, a system with 512 cpus reaches the limit for
maximum number of file descriptors that can be opened. To solve this
problem, the limit is raised to 2^15, which is a large enough number.
Below data is collected from AMD server systems while running turbostat:
|-----------+-------------------------------|
| # of cpus | # of opened fds for turbostat |
|-----------+-------------------------------|
| 128 | 260 |
|-----------+-------------------------------|
| 192 | 388 |
|-----------+-------------------------------|
| 512 | 1028 |
|-----------+-------------------------------|
So, the new max limit would be sufficient up to 2^14 cpus (but this
also depends on how many counters are enabled).
Reviewed-by: Doug Smythies <dsmythies@telus.net>
Tested-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Wyes Karny <wyes.karny@amd.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 752e3c53de ]
In the FireWire OHCI interrupt handler, if a bus reset interrupt has
occurred, mask bus reset interrupts until bus_reset_work has serviced and
cleared the interrupt.
Normally, we always leave bus reset interrupts masked. We infer the bus
reset from the self-ID interrupt that happens shortly thereafter. A
scenario where we unmask bus reset interrupts was introduced in 2008 in
a007bb857e: If
OHCI_PARAM_DEBUG_BUSRESETS (8) is set in the debug parameter bitmask, we
will unmask bus reset interrupts so we can log them.
irq_handler logs the bus reset interrupt. However, we can't clear the bus
reset event flag in irq_handler, because we won't service the event until
later. irq_handler exits with the event flag still set. If the
corresponding interrupt is still unmasked, the first bus reset will
usually freeze the system due to irq_handler being called again each
time it exits. This freeze can be reproduced by loading firewire_ohci
with "modprobe firewire_ohci debug=-1" (to enable all debugging output).
Apparently there are also some cases where bus_reset_work will get called
soon enough to clear the event, and operation will continue normally.
This freeze was first reported a few months after a007bb85 was committed,
but until now it was never fixed. The debug level could safely be set
to -1 through sysfs after the module was loaded, but this would be
ineffectual in logging bus reset interrupts since they were only
unmasked during initialization.
irq_handler will now leave the event flag set but mask bus reset
interrupts, so irq_handler won't be called again and there will be no
freeze. If OHCI_PARAM_DEBUG_BUSRESETS is enabled, bus_reset_work will
unmask the interrupt after servicing the event, so future interrupts
will be caught as desired.
As a side effect to this change, OHCI_PARAM_DEBUG_BUSRESETS can now be
enabled through sysfs in addition to during initial module loading.
However, when enabled through sysfs, logging of bus reset interrupts will
be effective only starting with the second bus reset, after
bus_reset_work has executed.
Signed-off-by: Adam Goldman <adamg@pobox.com>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e85006ae74 ]
The call to clk_enable() in gemini_sata_start_bridge() can fail.
Add a check to detect such failure.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a6380cb4c ]
If the RBUF logic is not reset when the kernel starts then there
may be some data left over from any network boot loader. If the
64-byte packet headers are enabled then this can be fatal.
Extend bcmgenet_dma_disable to do perform the reset, but not when
called from bcmgenet_resume in order to preserve a wake packet.
N.B. This different handling of resume is just based on a hunch -
why else wouldn't one reset the RBUF as well as the TBUF? If this
isn't the case then it's easy to change the patch to make the RBUF
reset unconditional.
See: https://github.com/raspberrypi/linux/issues/3850
See: https://github.com/raspberrypi/firmware/issues/1882
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Maarten Vanraes <maarten@rmail.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6bc5e70b1c ]
When wl suspend error occurs, for example BKOP or SSU timeout, the host
triggers an error handler and returns -EBUSY to break the wl suspend
process. However, it is possible for the runtime PM to enter wl suspend
again before the error handler has finished, and return -EINVAL because the
device is in an error state. To address this, ensure that the rumtime PM
waits for the error handler to finish, or trigger the error handler in such
cases, because returning -EINVAL can cause the I/O to hang.
Signed-off-by: Peter Wang <peter.wang@mediatek.com>
Link: https://lore.kernel.org/r/20240329015036.15707-1-peter.wang@mediatek.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 54babdc034 ]
When KCSAN and CONSTRUCTORS are enabled, one can trigger the
"Unpatched return thunk in use. This should not happen!"
catch-all warning.
Usually, when objtool runs on the .o objects, it does generate a section
.return_sites which contains all offsets in the objects to the return
thunks of the functions present there. Those return thunks then get
patched at runtime by the alternatives.
KCSAN and CONSTRUCTORS add this to the object file's .text.startup
section:
-------------------
Disassembly of section .text.startup:
...
0000000000000010 <_sub_I_00099_0>:
10: f3 0f 1e fa endbr64
14: e8 00 00 00 00 call 19 <_sub_I_00099_0+0x9>
15: R_X86_64_PLT32 __tsan_init-0x4
19: e9 00 00 00 00 jmp 1e <__UNIQUE_ID___addressable_cryptd_alloc_aead349+0x6>
1a: R_X86_64_PLT32 __x86_return_thunk-0x4
-------------------
which, if it is built as a module goes through the intermediary stage of
creating a <module>.mod.c file which, when translated, receives a second
constructor:
-------------------
Disassembly of section .text.startup:
0000000000000010 <_sub_I_00099_0>:
10: f3 0f 1e fa endbr64
14: e8 00 00 00 00 call 19 <_sub_I_00099_0+0x9>
15: R_X86_64_PLT32 __tsan_init-0x4
19: e9 00 00 00 00 jmp 1e <_sub_I_00099_0+0xe>
1a: R_X86_64_PLT32 __x86_return_thunk-0x4
...
0000000000000030 <_sub_I_00099_0>:
30: f3 0f 1e fa endbr64
34: e8 00 00 00 00 call 39 <_sub_I_00099_0+0x9>
35: R_X86_64_PLT32 __tsan_init-0x4
39: e9 00 00 00 00 jmp 3e <__ksymtab_cryptd_alloc_ahash+0x2>
3a: R_X86_64_PLT32 __x86_return_thunk-0x4
-------------------
in the .ko file.
Objtool has run already so that second constructor's return thunk cannot
be added to the .return_sites section and thus the return thunk remains
unpatched and the warning rightfully fires.
Drop KCSAN flags from the mod.c generation stage as those constructors
do not contain data races one would be interested about.
Debugged together with David Kaplan <David.Kaplan@amd.com> and Nikolay
Borisov <nik.borisov@suse.com>.
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Closes: https://lore.kernel.org/r/0851a207-7143-417e-be31-8bf2b3afb57d@molgen.mpg.de
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de> # Dell XPS 13
Reviewed-by: Nikolay Borisov <nik.borisov@suse.com>
Reviewed-by: Marco Elver <elver@google.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ecab2e645 ]
The event filter function test has been failing in our internal test
farm:
| # not ok 33 event filter function - test event filtering on functions
Running the test in verbose mode indicates that this is because the test
erroneously determines that kmem_cache_free() is the most common caller
of kmem_cache_free():
# # + cut -d: -f3 trace
# # + sed s/call_site=([^+]*)+0x.*/1/
# # + sort
# # + uniq -c
# # + sort
# # + tail -n 1
# # + sed s/^[ 0-9]*//
# # + target_func=kmem_cache_free
... and as kmem_cache_free() doesn't call itself, setting this as the
filter function for kmem_cache_free() results in no hits, and
consequently the test fails:
# # + grep kmem_cache_free trace
# # + grep kmem_cache_free
# # + wc -l
# # + hitcnt=0
# # + grep kmem_cache_free trace
# # + grep -v kmem_cache_free
# # + wc -l
# # + misscnt=0
# # + [ 0 -eq 0 ]
# # + exit_fail
This seems to be because the system in question has tasks with ':' in
their name (which a number of kernel worker threads have). These show up
in the trace, e.g.
test:.sh-1299 [004] ..... 2886.040608: kmem_cache_free: call_site=putname+0xa4/0xc8 ptr=000000000f4d22f4 name=names_cache
... and so when we try to extact the call_site with:
cut -d: -f3 trace | sed 's/call_site=\([^+]*\)+0x.*/\1/'
... the 'cut' command will extrace the column containing
'kmem_cache_free' rather than the column containing 'call_site=...', and
the 'sed' command will leave this unchanged. Consequently, the test will
decide to use 'kmem_cache_free' as the filter function, resulting in the
failure seen above.
Fix this by matching the 'call_site=<func>' part specifically to extract
the function name.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reported-by: Aishwarya TCV <aishwarya.tcv@arm.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-kselftest@vger.kernel.org
Cc: linux-trace-kernel@vger.kernel.org
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a8d89feba7 ]
This patch adds a missing check to bloom filter creating, rejecting
values above KMALLOC_MAX_SIZE. This brings the bloom map in line with
many other map types.
The lack of this protection can cause kernel crashes for value sizes
that overflow int's. Such a crash was caught by syzkaller. The next
patch adds more guard-rails at a lower level.
Signed-off-by: Andrei Matei <andreimatei1@gmail.com>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/r/20240327024245.318299-2-andreimatei1@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0cac183b98 ]
Due to a CP interrupt bug, bad packet garbage exception codes are raised.
Do a range check so that the debugger and runtime do not receive garbage
codes.
Update the user api to guard exception code type checking as well.
Signed-off-by: Jonathan Kim <jonathan.kim@amd.com>
Tested-by: Jesse Zhang <jesse.zhang@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f1aeab9fc ]
When attempting to exclusive open a device which has no exclusive open
permission, such as a physical device associated with the flakey dm
device, the open operation will fail, resulting in a mount failure.
In this particular scenario, we erroneously return -EINVAL instead of the
correct error code provided by the bdev_open_by_path() function, which is
-EBUSY.
Fix this, by returning error code from the bdev_open_by_path() function.
With this correction, the mount error message will align with that of
ext4 and xfs.
Reviewed-by: Boris Burkov <boris@bur.io>
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 429846b4b6 ]
When the "storcli2 show" command is executed for eHBA-9600, mpi3mr driver
prints this WARNING message:
memcpy: detected field-spanning write (size 128) of single field "bsg_reply_buf->reply_buf" at drivers/scsi/mpi3mr/mpi3mr_app.c:1658 (size 1)
WARNING: CPU: 0 PID: 12760 at drivers/scsi/mpi3mr/mpi3mr_app.c:1658 mpi3mr_bsg_request+0x6b12/0x7f10 [mpi3mr]
The cause of the WARN is 128 bytes memcpy to the 1 byte size array "__u8
replay_buf[1]" in the struct mpi3mr_bsg_in_reply_buf. The array is intended
to be a flexible length array, so the WARN is a false positive.
To suppress the WARN, remove the constant number '1' from the array
declaration and clarify that it has flexible length. Also, adjust the
memory allocation size to match the change.
Suggested-by: Sathya Prakash Veerichetty <sathya.prakash@broadcom.com>
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Link: https://lore.kernel.org/r/20240323084155.166835-1-shinichiro.kawasaki@wdc.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2deb2e971 ]
sk->sk_rcvbuf in __sock_queue_rcv_skb() and __sk_receive_skb() can be
changed by other threads. Mark this as benign using READ_ONCE().
This patch is aimed at reducing the number of benign races reported by
KCSAN in order to focus future debugging effort on harmful races.
Signed-off-by: linke li <lilinke99@qq.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 774f8841f5 ]
Running kernel-doc on ieee80211_i.h flagged the following:
net/mac80211/ieee80211_i.h:145: warning: expecting prototype for enum ieee80211_corrupt_data_flags. Prototype was for enum ieee80211_bss_corrupt_data_flags instead
net/mac80211/ieee80211_i.h:162: warning: expecting prototype for enum ieee80211_valid_data_flags. Prototype was for enum ieee80211_bss_valid_data_flags instead
Fix these warnings.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://msgid.link/20240314-kdoc-ieee80211_i-v1-1-72b91b55b257@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c95346ac91 ]
In punch_hole(), when the offset lies in the final block for a given
height, there is no hole to punch, but the maximum size check fails to
detect that. Consequently, punch_hole() will try to punch a hole beyond
the end of the metadata and fail. Fix the maximum size check.
Signed-off-by: Andrew Price <anprice@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb01163143 ]
Typically when an out of resource CQE status is detected, the
lpfc_ramp_down_queue_handler() logic is called to help reduce I/O load by
reducing an sdev's queue_depth.
However, the current lpfc_rampdown_queue_depth() logic does not help reduce
queue_depth. num_cmd_success is never updated and is always zero, which
means new_queue_depth will always be set to sdev->queue_depth. So,
new_queue_depth = sdev->queue_depth - new_queue_depth always sets
new_queue_depth to zero. And, scsi_change_queue_depth(sdev, 0) is
essentially a no-op.
Change the lpfc_ramp_down_queue_handler() logic to set new_queue_depth
equal to sdev->queue_depth subtracted from number of times num_rsrc_err was
incremented. If num_rsrc_err is >= sdev->queue_depth, then set
new_queue_depth equal to 1. Eventually, the frequency of Good_Status
frames will signal SCSI upper layer to auto increase the queue_depth back
to the driver default of 64 via scsi_handle_queue_ramp_up().
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20240305200503.57317-5-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4623713e7a ]
IRQF_ONESHOT is found to mask HBA generated interrupts when thread_fn is
running. As a result, some EQEs/CQEs miss timely processing resulting in
SCSI layer attempts to abort commands due to io_timeout. Abort CQEs are
also not processed leading to the observations of hangs and spam of "0748
abort handler timed out waiting for aborting I/O" log messages.
Remove the IRQF_ONESHOT flag. The cmpxchg and xchg atomic operations on
lpfc_queue->queue_claimed already protect potential parallel access to an
EQ/CQ should the thread_fn get interrupted by the primary irq handler.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20240305200503.57317-4-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ddf01f2f1 ]
There are cases after NPIV deletion where the fabric switch still believes
the NPIV is logged into the fabric. This occurs when a vport is
unregistered before the Remove All DA_ID CT and LOGO ELS are sent to the
fabric.
Currently fc_remove_host(), which calls dev_loss_tmo for all D_IDs including
the fabric D_ID, removes the last ndlp reference and frees the ndlp rport
object. This sometimes causes the race condition where the final DA_ID and
LOGO are skipped from being sent to the fabric switch.
Fix by moving the fc_remove_host() and scsi_remove_host() calls after DA_ID
and LOGO are sent.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20240305200503.57317-3-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e7728c81a ]
When parsing a GICv2 attribute that contains a cpuid, handle this
as the vcpu_id, not a vcpu_idx, as userspace cannot really know
the mapping between the two. For this, use kvm_get_vcpu_by_id()
instead of kvm_get_vcpu().
Take this opportunity to get rid of the pointless check against
online_vcpus, which doesn't make much sense either, and switch
to FIELD_GET as a way to extract the vcpu_id.
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230927090911.3355209-5-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Stable-dep-of: 6ddb4f372f ("KVM: arm64: vgic-v2: Check for non-NULL vCPU in vgic_v2_parse_attr()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 75961ffb5c ]
Using restricted DMA pools (CONFIG_DMA_RESTRICTED_POOL=y) in conjunction
with dynamic SWIOTLB (CONFIG_SWIOTLB_DYNAMIC=y) leads to the following
crash when initialising the restricted pools at boot-time:
| Unable to handle kernel NULL pointer dereference at virtual address 0000000000000008
| Internal error: Oops: 0000000096000005 [#1] PREEMPT SMP
| pc : rmem_swiotlb_device_init+0xfc/0x1ec
| lr : rmem_swiotlb_device_init+0xf0/0x1ec
| Call trace:
| rmem_swiotlb_device_init+0xfc/0x1ec
| of_reserved_mem_device_init_by_idx+0x18c/0x238
| of_dma_configure_id+0x31c/0x33c
| platform_dma_configure+0x34/0x80
faddr2line reveals that the crash is in the list validation code:
include/linux/list.h:83
include/linux/rculist.h:79
include/linux/rculist.h:106
kernel/dma/swiotlb.c:306
kernel/dma/swiotlb.c:1695
because add_mem_pool() is trying to list_add_rcu() to a NULL
'mem->pools'.
Fix the crash by initialising the 'mem->pools' list_head in
rmem_swiotlb_device_init() before calling add_mem_pool().
Reported-by: Nikita Ioffe <ioffe@google.com>
Tested-by: Nikita Ioffe <ioffe@google.com>
Fixes: 1aaa736815 ("swiotlb: allocate a new memory pool when existing pools are full")
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49a940dbdc ]
At the time of LPAR boot up, partition firmware provides Open Firmware
property ibm,dma-window for the PE. This property is provided on the PCI
bus the PE is attached to.
There are execptions where the partition firmware might not provide this
property for the PE at the time of LPAR boot up. One of the scenario is
where the firmware has frozen the PE due to some error condition. This
PE is frozen for 24 hours or unless the whole system is reinitialized.
Within this time frame, if the LPAR is booted, the frozen PE will be
presented to the LPAR but ibm,dma-window property could be missing.
Today, under these circumstances, the LPAR oopses with NULL pointer
dereference, when configuring the PCI bus the PE is attached to.
BUG: Kernel NULL pointer dereference on read at 0x000000c8
Faulting instruction address: 0xc0000000001024c0
Oops: Kernel access of bad area, sig: 7 [#1]
LE PAGE_SIZE=64K MMU=Radix SMP NR_CPUS=2048 NUMA pSeries
Modules linked in:
Supported: Yes
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 6.4.0-150600.9-default #1
Hardware name: IBM,9043-MRX POWER10 (raw) 0x800200 0xf000006 of:IBM,FW1060.00 (NM1060_023) hv:phyp pSeries
NIP: c0000000001024c0 LR: c0000000001024b0 CTR: c000000000102450
REGS: c0000000037db5c0 TRAP: 0300 Not tainted (6.4.0-150600.9-default)
MSR: 8000000002009033 <SF,VEC,EE,ME,IR,DR,RI,LE> CR: 28000822 XER: 00000000
CFAR: c00000000010254c DAR: 00000000000000c8 DSISR: 00080000 IRQMASK: 0
...
NIP [c0000000001024c0] pci_dma_bus_setup_pSeriesLP+0x70/0x2a0
LR [c0000000001024b0] pci_dma_bus_setup_pSeriesLP+0x60/0x2a0
Call Trace:
pci_dma_bus_setup_pSeriesLP+0x60/0x2a0 (unreliable)
pcibios_setup_bus_self+0x1c0/0x370
__of_scan_bus+0x2f8/0x330
pcibios_scan_phb+0x280/0x3d0
pcibios_init+0x88/0x12c
do_one_initcall+0x60/0x320
kernel_init_freeable+0x344/0x3e4
kernel_init+0x34/0x1d0
ret_from_kernel_user_thread+0x14/0x1c
Fixes: b1fc44eaa9 ("pseries/iommu/ddw: Fix kdump to work in absence of ibm,dma-window")
Signed-off-by: Gaurav Batra <gbatra@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20240422205141.10662-1-gbatra@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5babae777c ]
GRO-GSO path is supposed to be transparent and as such L3 flush checks are
relevant to all UDP flows merging in GRO. This patch uses the same logic
and code from tcp_gro_receive, terminating merge if flush is non zero.
Fixes: e20cf8d3f1 ("udp: implement GRO for plain UDP sockets.")
Signed-off-by: Richard Gobert <richardbgobert@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ef31ea5d0 ]
Commits a602456 ("udp: Add GRO functions to UDP socket") and 57c67ff ("udp:
additional GRO support") introduce incorrect usage of {ip,ipv6}_hdr in the
complete phase of gro. The functions always return skb->network_header,
which in the case of encapsulated packets at the gro complete phase, is
always set to the innermost L3 of the packet. That means that calling
{ip,ipv6}_hdr for skbs which completed the GRO receive phase (both in
gro_list and *_gro_complete) when parsing an encapsulated packet's _outer_
L3/L4 may return an unexpected value.
This incorrect usage leads to a bug in GRO's UDP socket lookup.
udp{4,6}_lib_lookup_skb functions use ip_hdr/ipv6_hdr respectively. These
*_hdr functions return network_header which will point to the innermost L3,
resulting in the wrong offset being used in __udp{4,6}_lib_lookup with
encapsulated packets.
This patch adds network_offset and inner_network_offset to napi_gro_cb, and
makes sure both are set correctly.
To fix the issue, network_offsets union is used inside napi_gro_cb, in
which both the outer and the inner network offsets are saved.
Reproduction example:
Endpoint configuration example (fou + local address bind)
# ip fou add port 6666 ipproto 4
# ip link add name tun1 type ipip remote 2.2.2.1 local 2.2.2.2 encap fou encap-dport 5555 encap-sport 6666 mode ipip
# ip link set tun1 up
# ip a add 1.1.1.2/24 dev tun1
Netperf TCP_STREAM result on net-next before patch is applied:
net-next main, GRO enabled:
$ netperf -H 1.1.1.2 -t TCP_STREAM -l 5
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
131072 16384 16384 5.28 2.37
net-next main, GRO disabled:
$ netperf -H 1.1.1.2 -t TCP_STREAM -l 5
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
131072 16384 16384 5.01 2745.06
patch applied, GRO enabled:
$ netperf -H 1.1.1.2 -t TCP_STREAM -l 5
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
131072 16384 16384 5.01 2877.38
Fixes: a6024562ff ("udp: Add GRO functions to UDP socket")
Signed-off-by: Richard Gobert <richardbgobert@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dff0b0161a ]
The existing code always pulls the IPv6 header and sets the transport
offset initially. Then optionally again pulls any extension headers in
ipv6_gso_pull_exthdrs and sets the transport offset again on return from
that call. skb->data is set at the start of the first extension header
before calling ipv6_gso_pull_exthdrs, and must disable the frag0
optimization because that function uses pskb_may_pull/pskb_pull instead of
skb_gro_ helpers. It sets the GRO offset to the TCP header with
skb_gro_pull and sets the transport header. Then returns skb->data to its
position before this block.
This commit introduces a new helper function - ipv6_gro_pull_exthdrs -
which is used in ipv6_gro_receive to pull ipv6 ext headers instead of
ipv6_gso_pull_exthdrs. Thus, there is no modification of skb->data, all
operations use skb_gro_* helpers, and the frag0 fast path can be taken for
IPv6 packets with ext headers.
Signed-off-by: Richard Gobert <richardbgobert@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/504130f6-b56c-4dcc-882c-97942c59f5b7@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 5ef31ea5d0 ("net: gro: fix udp bad offset in socket lookup by adding {inner_}network_offset to napi_gro_cb")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc1092f515 ]
KMSAN reported uninit-value access in __ip_make_skb() [1]. __ip_make_skb()
tests HDRINCL to know if the skb has icmphdr. However, HDRINCL can cause a
race condition. If calling setsockopt(2) with IP_HDRINCL changes HDRINCL
while __ip_make_skb() is running, the function will access icmphdr in the
skb even if it is not included. This causes the issue reported by KMSAN.
Check FLOWI_FLAG_KNOWN_NH on fl4->flowi4_flags instead of testing HDRINCL
on the socket.
Also, fl4->fl4_icmp_type and fl4->fl4_icmp_code are not initialized. These
are union in struct flowi4 and are implicitly initialized by
flowi4_init_output(), but we should not rely on specific union layout.
Initialize these explicitly in raw_sendmsg().
[1]
BUG: KMSAN: uninit-value in __ip_make_skb+0x2b74/0x2d20 net/ipv4/ip_output.c:1481
__ip_make_skb+0x2b74/0x2d20 net/ipv4/ip_output.c:1481
ip_finish_skb include/net/ip.h:243 [inline]
ip_push_pending_frames+0x4c/0x5c0 net/ipv4/ip_output.c:1508
raw_sendmsg+0x2381/0x2690 net/ipv4/raw.c:654
inet_sendmsg+0x27b/0x2a0 net/ipv4/af_inet.c:851
sock_sendmsg_nosec net/socket.c:730 [inline]
__sock_sendmsg+0x274/0x3c0 net/socket.c:745
__sys_sendto+0x62c/0x7b0 net/socket.c:2191
__do_sys_sendto net/socket.c:2203 [inline]
__se_sys_sendto net/socket.c:2199 [inline]
__x64_sys_sendto+0x130/0x200 net/socket.c:2199
do_syscall_64+0xd8/0x1f0 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x6d/0x75
Uninit was created at:
slab_post_alloc_hook mm/slub.c:3804 [inline]
slab_alloc_node mm/slub.c:3845 [inline]
kmem_cache_alloc_node+0x5f6/0xc50 mm/slub.c:3888
kmalloc_reserve+0x13c/0x4a0 net/core/skbuff.c:577
__alloc_skb+0x35a/0x7c0 net/core/skbuff.c:668
alloc_skb include/linux/skbuff.h:1318 [inline]
__ip_append_data+0x49ab/0x68c0 net/ipv4/ip_output.c:1128
ip_append_data+0x1e7/0x260 net/ipv4/ip_output.c:1365
raw_sendmsg+0x22b1/0x2690 net/ipv4/raw.c:648
inet_sendmsg+0x27b/0x2a0 net/ipv4/af_inet.c:851
sock_sendmsg_nosec net/socket.c:730 [inline]
__sock_sendmsg+0x274/0x3c0 net/socket.c:745
__sys_sendto+0x62c/0x7b0 net/socket.c:2191
__do_sys_sendto net/socket.c:2203 [inline]
__se_sys_sendto net/socket.c:2199 [inline]
__x64_sys_sendto+0x130/0x200 net/socket.c:2199
do_syscall_64+0xd8/0x1f0 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x6d/0x75
CPU: 1 PID: 15709 Comm: syz-executor.7 Not tainted 6.8.0-11567-gb3603fcb79b1 #25
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-1.fc39 04/01/2014
Fixes: 99e5acae19 ("ipv4: Fix potential uninit variable access bug in __ip_make_skb()")
Reported-by: syzkaller <syzkaller@googlegroups.com>
Signed-off-by: Shigeru Yoshida <syoshida@redhat.com>
Link: https://lore.kernel.org/r/20240430123945.2057348-1-syoshida@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a2e4d37af ]
Symptom:
When the hsuid attribute is set for the first time on an IQD Layer3
device while the corresponding network interface is already UP,
the kernel will try to execute a napi function pointer that is NULL.
Example:
---------------------------------------------------------------------------
[ 2057.572696] illegal operation: 0001 ilc:1 [#1] SMP
[ 2057.572702] Modules linked in: af_iucv qeth_l3 zfcp scsi_transport_fc sunrpc nft_fib_inet nft_fib_ipv4 nft_fib_ipv6 nft_fib nft_reject_inet nf_reject_ipv4 nf_reject_ipv6
nft_reject nft_ct nf_tables_set nft_chain_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 ip_set nf_tables libcrc32c nfnetlink ghash_s390 prng xts aes_s390 des_s390 de
s_generic sha3_512_s390 sha3_256_s390 sha512_s390 vfio_ccw vfio_mdev mdev vfio_iommu_type1 eadm_sch vfio ext4 mbcache jbd2 qeth_l2 bridge stp llc dasd_eckd_mod qeth dasd_mod
qdio ccwgroup pkey zcrypt
[ 2057.572739] CPU: 6 PID: 60182 Comm: stress_client Kdump: loaded Not tainted 4.18.0-541.el8.s390x #1
[ 2057.572742] Hardware name: IBM 3931 A01 704 (LPAR)
[ 2057.572744] Krnl PSW : 0704f00180000000 0000000000000002 (0x2)
[ 2057.572748] R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:0 AS:3 CC:3 PM:0 RI:0 EA:3
[ 2057.572751] Krnl GPRS: 0000000000000004 0000000000000000 00000000a3b008d8 0000000000000000
[ 2057.572754] 00000000a3b008d8 cb923a29c779abc5 0000000000000000 00000000814cfd80
[ 2057.572756] 000000000000012c 0000000000000000 00000000a3b008d8 00000000a3b008d8
[ 2057.572758] 00000000bab6d500 00000000814cfd80 0000000091317e46 00000000814cfc68
[ 2057.572762] Krnl Code:#0000000000000000: 0000 illegal
>0000000000000002: 0000 illegal
0000000000000004: 0000 illegal
0000000000000006: 0000 illegal
0000000000000008: 0000 illegal
000000000000000a: 0000 illegal
000000000000000c: 0000 illegal
000000000000000e: 0000 illegal
[ 2057.572800] Call Trace:
[ 2057.572801] ([<00000000ec639700>] 0xec639700)
[ 2057.572803] [<00000000913183e2>] net_rx_action+0x2ba/0x398
[ 2057.572809] [<0000000091515f76>] __do_softirq+0x11e/0x3a0
[ 2057.572813] [<0000000090ce160c>] do_softirq_own_stack+0x3c/0x58
[ 2057.572817] ([<0000000090d2cbd6>] do_softirq.part.1+0x56/0x60)
[ 2057.572822] [<0000000090d2cc60>] __local_bh_enable_ip+0x80/0x98
[ 2057.572825] [<0000000091314706>] __dev_queue_xmit+0x2be/0xd70
[ 2057.572827] [<000003ff803dd6d6>] afiucv_hs_send+0x24e/0x300 [af_iucv]
[ 2057.572830] [<000003ff803dd88a>] iucv_send_ctrl+0x102/0x138 [af_iucv]
[ 2057.572833] [<000003ff803de72a>] iucv_sock_connect+0x37a/0x468 [af_iucv]
[ 2057.572835] [<00000000912e7e90>] __sys_connect+0xa0/0xd8
[ 2057.572839] [<00000000912e9580>] sys_socketcall+0x228/0x348
[ 2057.572841] [<0000000091514e1a>] system_call+0x2a6/0x2c8
[ 2057.572843] Last Breaking-Event-Address:
[ 2057.572844] [<0000000091317e44>] __napi_poll+0x4c/0x1d8
[ 2057.572846]
[ 2057.572847] Kernel panic - not syncing: Fatal exception in interrupt
-------------------------------------------------------------------------------------------
Analysis:
There is one napi structure per out_q: card->qdio.out_qs[i].napi
The napi.poll functions are set during qeth_open().
Since
commit 1cfef80d4c ("s390/qeth: Don't call dev_close/dev_open (DOWN/UP)")
qeth_set_offline()/qeth_set_online() no longer call dev_close()/
dev_open(). So if qeth_free_qdio_queues() cleared
card->qdio.out_qs[i].napi.poll while the network interface was UP and the
card was offline, they are not set again.
Reproduction:
chzdev -e $devno layer2=0
ip link set dev $network_interface up
echo 0 > /sys/bus/ccwgroup/devices/0.0.$devno/online
echo foo > /sys/bus/ccwgroup/devices/0.0.$devno/hsuid
echo 1 > /sys/bus/ccwgroup/devices/0.0.$devno/online
-> Crash (can be enforced e.g. by af_iucv connect(), ip link down/up, ...)
Note that a Completion Queue (CQ) is only enabled or disabled, when hsuid
is set for the first time or when it is removed.
Workarounds:
- Set hsuid before setting the device online for the first time
or
- Use chzdev -d $devno; chzdev $devno hsuid=xxx; chzdev -e $devno;
to set hsuid on an existing device. (this will remove and recreate the
network interface)
Fix:
There is no need to free the output queues when a completion queue is
added or removed.
card->qdio.state now indicates whether the inbound buffer pool and the
outbound queues are allocated.
card->qdio.c_q indicates whether a CQ is allocated.
Fixes: 1cfef80d4c ("s390/qeth: Don't call dev_close/dev_open (DOWN/UP)")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240430091004.2265683-1-wintera@linux.ibm.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f778941913 ]
Ensure the inner IP header is part of skb's linear data before reading
its ECN bits. Otherwise we might read garbage.
One symptom is the system erroneously logging errors like
"vxlan: non-ECT from xxx.xxx.xxx.xxx with TOS=xxxx".
Similar bugs have been fixed in geneve, ip_tunnel and ip6_tunnel (see
commit 1ca1ba465e ("geneve: make sure to pull inner header in
geneve_rx()") for example). So let's reuse the same code structure for
consistency. Maybe we'll can add a common helper in the future.
Fixes: d342894c5d ("vxlan: virtual extensible lan")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://lore.kernel.org/r/1239c8db54efec341dd6455c77e0380f58923a3c.1714495737.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8953285d7b ]
The find connection logic of Transarc's Rx was modified in the mid-1990s
to support multi-homed servers which might send a response packet from
an address other than the destination address in the received packet.
The rules for accepting a packet by an Rx initiator (RX_CLIENT_CONNECTION)
were altered to permit acceptance of a packet from any address provided
that the port number was unchanged and all of the connection identifiers
matched (Epoch, CID, SecurityClass, ...).
This change applies the same rules to the Linux implementation which makes
it consistent with IBM AFS 3.6, Arla, OpenAFS and AuriStorFS.
Fixes: 17926a7932 ("[AF_RXRPC]: Provide secure RxRPC sockets for use by userspace and kernel both")
Signed-off-by: Jeffrey Altman <jaltman@auristor.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Marc Dionne <marc.dionne@auristor.com>
Link: https://lore.kernel.org/r/20240419163057.4141728-1-marc.dionne@auristor.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d091e579b8 ]
SKB_GSO_FRAGLIST skbs must not be linearized, otherwise they become
invalid. Return NULL if such an skb is passed to skb_copy or
skb_copy_expand, in order to prevent a crash on a potential later
call to skb_gso_segment.
Fixes: 3a1296a38d ("net: Support GRO/GSO fraglist chaining.")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59c878cbcd ]
Calling skb_copy on a SKB_GSO_FRAGLIST skb is not valid, since it returns
an invalid linearized skb. This code only needs to change the ethernet
header, so pskb_copy is the right function to call here.
Fixes: 6db6f0eae6 ("bridge: multicast to unicast")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4756fa529b ]
If spi_sync() is called with the non-empty queue and the same spi_message
is then reused, the complete callback for the message remains set while
the context is cleared, leading to a null pointer dereference when the
callback is invoked from spi_finalize_current_message().
With function inlining disabled, the call stack might look like this:
_raw_spin_lock_irqsave from complete_with_flags+0x18/0x58
complete_with_flags from spi_complete+0x8/0xc
spi_complete from spi_finalize_current_message+0xec/0x184
spi_finalize_current_message from spi_transfer_one_message+0x2a8/0x474
spi_transfer_one_message from __spi_pump_transfer_message+0x104/0x230
__spi_pump_transfer_message from __spi_transfer_message_noqueue+0x30/0xc4
__spi_transfer_message_noqueue from __spi_sync+0x204/0x248
__spi_sync from spi_sync+0x24/0x3c
spi_sync from mcp251xfd_regmap_crc_read+0x124/0x28c [mcp251xfd]
mcp251xfd_regmap_crc_read [mcp251xfd] from _regmap_raw_read+0xf8/0x154
_regmap_raw_read from _regmap_bus_read+0x44/0x70
_regmap_bus_read from _regmap_read+0x60/0xd8
_regmap_read from regmap_read+0x3c/0x5c
regmap_read from mcp251xfd_alloc_can_err_skb+0x1c/0x54 [mcp251xfd]
mcp251xfd_alloc_can_err_skb [mcp251xfd] from mcp251xfd_irq+0x194/0xe70 [mcp251xfd]
mcp251xfd_irq [mcp251xfd] from irq_thread_fn+0x1c/0x78
irq_thread_fn from irq_thread+0x118/0x1f4
irq_thread from kthread+0xd8/0xf4
kthread from ret_from_fork+0x14/0x28
Fix this by also setting message->complete to NULL when the transfer is
complete.
Fixes: ae7d2346dc ("spi: Don't use the message queue if possible in spi_sync")
Signed-off-by: Mans Rullgard <mans@mansr.com>
Link: https://lore.kernel.org/r/20240430182705.13019-1-mans@mansr.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9067eccdd7 ]
The selftest for the driver sends a dummy packet and checks if the
packet will be received properly as it should be. The regular TX path
and the selftest can use the same network queue so locking is required
and was missing in the selftest path. This was addressed in the commit
cited below.
Unfortunately locking the TX queue requires BH to be disabled which is
not the case in selftest path which is invoked in process context.
Lockdep should be complaining about this.
Use __netif_tx_lock_bh() for TX queue locking.
Fixes: c650e04898 ("cxgb4: Fix race between loopback and normal Tx path")
Reported-by: "John B. Wyatt IV" <jwyatt@redhat.com>
Closes: https://lore.kernel.org/all/Zic0ot5aGgR-V4Ks@thinkpad2021/
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20240429091147.YWAaal4v@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c158cf9147 ]
The documentation for device_get_named_child_node() mentions this
important point:
"
The caller is responsible for calling fwnode_handle_put() on the
returned fwnode pointer.
"
Add fwnode_handle_put() to avoid a leaked reference.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Fixes: 08c2a4bc9f ("ALSA: hda: move Intel SoundWire ACPI scan to dedicated module")
Message-ID: <20240426152731.38420-1-pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6db26f9ea4 ]
Amlogic sound cards do create a lot of pcm interfaces, possibly more than
8. Some pcm interfaces are internal (like DPCM backends and c2c) and not
exposed to userspace.
Those interfaces still increase the number passed to snd_find_free_minor(),
which eventually exceeds 8 causing -EBUSY error on card registration if
CONFIG_SND_DYNAMIC_MINORS=n and the interface is exposed to userspace.
select CONFIG_SND_DYNAMIC_MINORS for Amlogic cards to avoid the problem.
Fixes: 7864a79f37 ("ASoC: meson: add axg sound card support")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20240426134150.3053741-1-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f949ed458a ]
So far, the formatters have been reset/enabled using the .prepare()
callback. This was done in this callback because walking the formatters use
a mutex. A mutex is used because formatter handling require dealing
possibly slow clock operation.
With the support of non-atomic, .trigger() callback may be used which also
allows to properly enable and disable formatters on start but also
pause/resume.
This solve a random shift on TDMIN as well repeated samples on for TDMOUT.
Fixes: d60e4f1e4b ("ASoC: meson: add tdm interface driver")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20240426152946.3078805-4-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b11d26660d ]
With the AXG audio subsystem, there is a possible random channel shift on
TDM capture, when the slot number per lane is more than 2, and there is
more than one lane used.
The problem has been there since the introduction of the axg audio support
but such scenario is pretty uncommon. This is why there is no loud
complains about the problem.
Solving the problem require to make the links non-atomic and use the
trigger() callback to start FEs and BEs in the appropriate order.
This was tried in the past and reverted because it caused the block irq to
sleep while atomic. However, instead of reverting, the solution is to call
snd_pcm_period_elapsed() in a non atomic context.
Use the bottom half of a threaded IRQ to do so.
Fixes: 6dc4fa179f ("ASoC: meson: add axg fifo base driver")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20240426152946.3078805-2-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b22ea4ef4c ]
VXLAN stores per-VNI statistics using vxlan_vnifilter_count().
These statistics were not updated when arp_reduce() failed its
pskb_may_pull() call.
Use vxlan_vnifilter_count() to update the VNI counter when that
happens.
Fixes: 4095e0e132 ("drivers: vxlan: vnifilter: per vni stats")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6dee402dab ]
VXLAN devices update their stats locklessly. Therefore these counters
should either be stored in per-cpu data structures or the updates
should be done using atomic increments.
Since the net_device_core_stats infrastructure is already used in
vxlan_rcv(), use it for the other rx_dropped and tx_dropped counter
updates. Update the other counters atomically using DEV_STATS_INC().
Fixes: d342894c5d ("vxlan: virtual extensible lan")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f26f719a36 ]
When calling qede_parse_actions() then the
return code was only used for a non-zero check,
and then -EINVAL was returned.
qede_parse_actions() can currently fail with:
* -EINVAL
* -EOPNOTSUPP
This patch changes the code to use the actual
return code, not just return -EINVAL.
The blaimed commit broke the implicit assumption
that only -EINVAL would ever be returned.
Only compile tested.
Fixes: 319a1d1947 ("flow_offload: check for basic action hw stats type")
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27b44414a3 ]
In qede_flow_spec_to_rule(), when calling
qede_parse_flow_attr() then the return code
was only used for a non-zero check, and then
-EINVAL was returned.
qede_parse_flow_attr() can currently fail with:
* -EINVAL
* -EOPNOTSUPP
* -EPROTONOSUPPORT
This patch changes the code to use the actual
return code, not just return -EINVAL.
The blaimed commit introduced qede_flow_spec_to_rule(),
and this call to qede_parse_flow_attr(), it looks
like it just duplicated how it was already used.
Only compile tested.
Fixes: 37c5d3efd7 ("qede: use ethtool_rx_flow_rule() to remove duplicated parser code")
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fcee2065a1 ]
In qede_add_tc_flower_fltr(), when calling
qede_parse_flow_attr() then the return code
was only used for a non-zero check, and then
-EINVAL was returned.
qede_parse_flow_attr() can currently fail with:
* -EINVAL
* -EOPNOTSUPP
* -EPROTONOSUPPORT
This patch changes the code to use the actual
return code, not just return -EINVAL.
The blaimed commit introduced these functions.
Only compile tested.
Fixes: 2ce9c93eac ("qede: Ingress tc flower offload (drop action) support.")
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e25714466a ]
Explicitly set 'rc' (return code), before jumping to the
unlock and return path.
By not having any code depend on that 'rc' remains at
it's initial value of -EINVAL, then we can re-use 'rc' for
the return code of function calls in subsequent patches.
Only compile tested.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: fcee2065a1 ("net: qede: use return from qede_parse_flow_attr() for flower")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8289fd3fa ]
A side effect of making the dock monitoring interrupt-driven was that
we'd be very quick to program a freshly connected dock. However, for
unclear reasons, the dock does not work when we do that - despite the
FPGA netlist upload going just fine. We work around this by adding a
delay before programming the dock; for safety, the value is several
times as much as was determined empirically.
Note that a badly timed dock hot-plug would have triggered the problem
even before the referenced commit - but now it would happen 100% instead
of about 3% of the time, thus making it impossible to work around by
re-plugging.
Fixes: fbb64eedf5 ("ALSA: emu10k1: make E-MU dock monitoring interrupt-driven")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218584
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <20240428093716.3198666-6-oswald.buddenhagen@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f848337cd8 ]
The actual event processing was already done by workqueue items. We can
move the event dispatching there as well, rather than doing it already
in the interrupt handler callback.
This change has a rather profound "side effect" on the reliability of
the FPGA programming: once we enter programming mode, we must not issue
any snd_emu1010_fpga_{read,write}() calls until we're done, as these
would badly mess up the programming protocol. But exactly that would
happen when trying to program the dock, as that triggers GPIO interrupts
as a side effect. This is mitigated by deferring the actual interrupt
handling, as workqueue items are not re-entrant.
To avoid scheduling the dispatcher on non-events, we now explicitly
ignore GPIO IRQs triggered by "uninteresting" pins, which happens a lot
as a side effect of calling snd_emu1010_fpga_{read,write}().
Fixes: fbb64eedf5 ("ALSA: emu10k1: make E-MU dock monitoring interrupt-driven")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218584
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <20240428093716.3198666-4-oswald.buddenhagen@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28deafd0fb ]
Pulled out of the next patch to improve its legibility.
As the function is now available, call it directly from
snd_emu10k1_emu1010_init(), thus making the MicroDock firmware loading
synchronous - there isn't really a reason not to. Note that this does
not affect the AudioDocks of rev1 cards, as these have no independent
power supplies, and thus come up only a while after the main card is
initialized.
As a drive-by, adjust the priorities of two messages to better reflect
their impact.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <20240428093716.3198666-3-oswald.buddenhagen@gmx.de>
Stable-dep-of: f848337cd8 ("ALSA: emu10k1: move the whole GPIO event handling to the workqueue")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 398321d753 ]
While there are two separate IRQ status bits for dock attach and detach,
the hardware appears to mix them up more or less randomly, making them
useless for tracking what actually happened. It is much safer to check
the dock status separately and proceed based on that, as the old polling
code did.
Note that the code assumes that only the dock can be hot-plugged - if
other option card bits changed, the logic would break.
Fixes: fbb64eedf5 ("ALSA: emu10k1: make E-MU dock monitoring interrupt-driven")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218584
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <20240428093716.3198666-2-oswald.buddenhagen@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b961ec10b9 ]
The return-address (RA) register r14 is specified as volatile in the
s390x ELF ABI [1]. Nevertheless proper CFI directives must be provided
for an unwinder to restore the return address, if the RA register
value is changed from its value at function entry, as it is the case.
[1]: s390x ELF ABI, https://github.com/IBM/s390x-abi/releases
Fixes: 4bff8cb545 ("s390: convert to GENERIC_VDSO")
Signed-off-by: Jens Remus <jremus@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 42f853b428 ]
Drop the flow-hash of the skb when forwarding to the L2TP netdev.
This avoids the L2TP qdisc from using the flow-hash from the outer
packet, which is identical for every flow within the tunnel.
This does not affect every platform but is specific for the ethernet
driver. It depends on the platform including L4 information in the
flow-hash.
One such example is the Mediatek Filogic MT798x family of networking
processors.
Fixes: d9e31d17ce ("l2tp: Add L2TP ethernet pseudowire support")
Acked-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240424171110.13701-1-mail@david-bauer.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b911a9690 ]
syzbot triggered various splats (see [0] and links) by a crafted GSO
packet of VIRTIO_NET_HDR_GSO_UDP layering the following protocols:
ETH_P_8021AD + ETH_P_NSH + ETH_P_IPV6 + IPPROTO_UDP
NSH can encapsulate IPv4, IPv6, Ethernet, NSH, and MPLS. As the inner
protocol can be Ethernet, NSH GSO handler, nsh_gso_segment(), calls
skb_mac_gso_segment() to invoke inner protocol GSO handlers.
nsh_gso_segment() does the following for the original skb before
calling skb_mac_gso_segment()
1. reset skb->network_header
2. save the original skb->{mac_heaeder,mac_len} in a local variable
3. pull the NSH header
4. resets skb->mac_header
5. set up skb->mac_len and skb->protocol for the inner protocol.
and does the following for the segmented skb
6. set ntohs(ETH_P_NSH) to skb->protocol
7. push the NSH header
8. restore skb->mac_header
9. set skb->mac_header + mac_len to skb->network_header
10. restore skb->mac_len
There are two problems in 6-7 and 8-9.
(a)
After 6 & 7, skb->data points to the NSH header, so the outer header
(ETH_P_8021AD in this case) is stripped when skb is sent out of netdev.
Also, if NSH is encapsulated by NSH + Ethernet (so NSH-Ethernet-NSH),
skb_pull() in the first nsh_gso_segment() will make skb->data point
to the middle of the outer NSH or Ethernet header because the Ethernet
header is not pulled by the second nsh_gso_segment().
(b)
While restoring skb->{mac_header,network_header} in 8 & 9,
nsh_gso_segment() does not assume that the data in the linear
buffer is shifted.
However, udp6_ufo_fragment() could shift the data and change
skb->mac_header accordingly as demonstrated by syzbot.
If this happens, even the restored skb->mac_header points to
the middle of the outer header.
It seems nsh_gso_segment() has never worked with outer headers so far.
At the end of nsh_gso_segment(), the outer header must be restored for
the segmented skb, instead of the NSH header.
To do that, let's calculate the outer header position relatively from
the inner header and set skb->{data,mac_header,protocol} properly.
[0]:
BUG: KMSAN: uninit-value in ipvlan_process_outbound drivers/net/ipvlan/ipvlan_core.c:524 [inline]
BUG: KMSAN: uninit-value in ipvlan_xmit_mode_l3 drivers/net/ipvlan/ipvlan_core.c:602 [inline]
BUG: KMSAN: uninit-value in ipvlan_queue_xmit+0xf44/0x16b0 drivers/net/ipvlan/ipvlan_core.c:668
ipvlan_process_outbound drivers/net/ipvlan/ipvlan_core.c:524 [inline]
ipvlan_xmit_mode_l3 drivers/net/ipvlan/ipvlan_core.c:602 [inline]
ipvlan_queue_xmit+0xf44/0x16b0 drivers/net/ipvlan/ipvlan_core.c:668
ipvlan_start_xmit+0x5c/0x1a0 drivers/net/ipvlan/ipvlan_main.c:222
__netdev_start_xmit include/linux/netdevice.h:4989 [inline]
netdev_start_xmit include/linux/netdevice.h:5003 [inline]
xmit_one net/core/dev.c:3547 [inline]
dev_hard_start_xmit+0x244/0xa10 net/core/dev.c:3563
__dev_queue_xmit+0x33ed/0x51c0 net/core/dev.c:4351
dev_queue_xmit include/linux/netdevice.h:3171 [inline]
packet_xmit+0x9c/0x6b0 net/packet/af_packet.c:276
packet_snd net/packet/af_packet.c:3081 [inline]
packet_sendmsg+0x8aef/0x9f10 net/packet/af_packet.c:3113
sock_sendmsg_nosec net/socket.c:730 [inline]
__sock_sendmsg net/socket.c:745 [inline]
__sys_sendto+0x735/0xa10 net/socket.c:2191
__do_sys_sendto net/socket.c:2203 [inline]
__se_sys_sendto net/socket.c:2199 [inline]
__x64_sys_sendto+0x125/0x1c0 net/socket.c:2199
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xcf/0x1e0 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x63/0x6b
Uninit was created at:
slab_post_alloc_hook mm/slub.c:3819 [inline]
slab_alloc_node mm/slub.c:3860 [inline]
__do_kmalloc_node mm/slub.c:3980 [inline]
__kmalloc_node_track_caller+0x705/0x1000 mm/slub.c:4001
kmalloc_reserve+0x249/0x4a0 net/core/skbuff.c:582
__alloc_skb+0x352/0x790 net/core/skbuff.c:651
skb_segment+0x20aa/0x7080 net/core/skbuff.c:4647
udp6_ufo_fragment+0xcab/0x1150 net/ipv6/udp_offload.c:109
ipv6_gso_segment+0x14be/0x2ca0 net/ipv6/ip6_offload.c:152
skb_mac_gso_segment+0x3e8/0x760 net/core/gso.c:53
nsh_gso_segment+0x6f4/0xf70 net/nsh/nsh.c:108
skb_mac_gso_segment+0x3e8/0x760 net/core/gso.c:53
__skb_gso_segment+0x4b0/0x730 net/core/gso.c:124
skb_gso_segment include/net/gso.h:83 [inline]
validate_xmit_skb+0x107f/0x1930 net/core/dev.c:3628
__dev_queue_xmit+0x1f28/0x51c0 net/core/dev.c:4343
dev_queue_xmit include/linux/netdevice.h:3171 [inline]
packet_xmit+0x9c/0x6b0 net/packet/af_packet.c:276
packet_snd net/packet/af_packet.c:3081 [inline]
packet_sendmsg+0x8aef/0x9f10 net/packet/af_packet.c:3113
sock_sendmsg_nosec net/socket.c:730 [inline]
__sock_sendmsg net/socket.c:745 [inline]
__sys_sendto+0x735/0xa10 net/socket.c:2191
__do_sys_sendto net/socket.c:2203 [inline]
__se_sys_sendto net/socket.c:2199 [inline]
__x64_sys_sendto+0x125/0x1c0 net/socket.c:2199
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xcf/0x1e0 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x63/0x6b
CPU: 1 PID: 5101 Comm: syz-executor421 Not tainted 6.8.0-rc5-syzkaller-00297-gf2e367d6ad3b #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/25/2024
Fixes: c411ed8545 ("nsh: add GSO support")
Reported-and-tested-by: syzbot+42a0dc856239de4de60e@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=42a0dc856239de4de60e
Reported-and-tested-by: syzbot+c298c9f0e46a3c86332b@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=c298c9f0e46a3c86332b
Link: https://lore.kernel.org/netdev/20240415222041.18537-1-kuniyu@amazon.com/
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20240424023549.21862-1-kuniyu@amazon.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f299ee709f ]
We try to access count + 1 byte from userspace with memdup_user(buffer,
count + 1). However, the userspace only provides buffer of count bytes and
only these count bytes are verified to be okay to access. To ensure the
copied buffer is NUL terminated, we use memdup_user_nul instead.
Fixes: 3a2eb515d1 ("octeontx2-af: Fix an off by one in rvu_dbg_qsize_write()")
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Link: https://lore.kernel.org/r/20240424-fix-oob-read-v2-6-f1f1b53a10f4@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c34096c7f ]
Currently, we allocate a nbytes-sized kernel buffer and copy nbytes from
userspace to that buffer. Later, we use sscanf on this buffer but we don't
ensure that the string is terminated inside the buffer, this can lead to
OOB read when using sscanf. Fix this issue by using memdup_user_nul
instead of memdup_user.
Fixes: 7afc5dbde0 ("bna: Add debugfs interface.")
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Link: https://lore.kernel.org/r/20240424-fix-oob-read-v2-2-f1f1b53a10f4@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5bcf0dcbf9 ]
When redirecting a packet using XDP, the bpf_redirect_map() helper will set
up the redirect destination information in struct bpf_redirect_info (using
the __bpf_xdp_redirect_map() helper function), and the xdp_do_redirect()
function will read this information after the XDP program returns and pass
the frame on to the right redirect destination.
When using the BPF_F_BROADCAST flag to do multicast redirect to a whole
map, __bpf_xdp_redirect_map() sets the 'map' pointer in struct
bpf_redirect_info to point to the destination map to be broadcast. And
xdp_do_redirect() reacts to the value of this map pointer to decide whether
it's dealing with a broadcast or a single-value redirect. However, if the
destination map is being destroyed before xdp_do_redirect() is called, the
map pointer will be cleared out (by bpf_clear_redirect_map()) without
waiting for any XDP programs to stop running. This causes xdp_do_redirect()
to think that the redirect was to a single target, but the target pointer
is also NULL (since broadcast redirects don't have a single target), so
this causes a crash when a NULL pointer is passed to dev_map_enqueue().
To fix this, change xdp_do_redirect() to react directly to the presence of
the BPF_F_BROADCAST flag in the 'flags' value in struct bpf_redirect_info
to disambiguate between a single-target and a broadcast redirect. And only
read the 'map' pointer if the broadcast flag is set, aborting if that has
been cleared out in the meantime. This prevents the crash, while keeping
the atomic (cmpxchg-based) clearing of the map pointer itself, and without
adding any more checks in the non-broadcast fast path.
Fixes: e624d4ed4a ("xdp: Extend xdp_redirect_map with broadcast support")
Reported-and-tested-by: syzbot+af9492708df9797198d6@syzkaller.appspotmail.com
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Stanislav Fomichev <sdf@google.com>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Link: https://lore.kernel.org/r/20240418071840.156411-1-toke@redhat.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 412050af2e ]
The function __storage_key_init_range() expects the end address to be
the first byte outside the range to be initialized. I.e. end - start
should be the size of the area to be initialized.
The current code works because __storage_key_init_range() will still loop
over every page in the range, but it is slower than using sske_frame().
Fixes: 3afdfca698 ("s390/mm: Clear skeys for newly mapped huge guest pmds")
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Link: https://lore.kernel.org/r/20240416114220.28489-3-imbrenda@linux.ibm.com
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 843c328068 ]
The function __storage_key_init_range() expects the end address to be
the first byte outside the range to be initialized. I.e. end - start
should be the size of the area to be initialized.
The current code works because __storage_key_init_range() will still loop
over every page in the range, but it is slower than using sske_frame().
Fixes: 964c2c05c9 ("s390/mm: Clear huge page storage keys on enable_skey")
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Link: https://lore.kernel.org/r/20240416114220.28489-2-imbrenda@linux.ibm.com
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4cbb5050bf ]
When creating controls attached to widgets, there are a lot of rules if
they get their name prefixed with widget name or not. Due to that
controls ended up with weirdly looking names like "ssp0_fe DSP Volume",
while topology set it to "DSP Volume".
Fix this by setting no_wname_in_kcontrol_name to true in avs topology
widgets which disables unwanted behaviour.
Fixes: be2b81b519 ("ASoC: Intel: avs: Parse control tuples")
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20240418142621.2487478-1-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0064db9ce4 ]
The version format string in the AXI SPI Engine driver was probably
intended to print the version number in the same format as the DT
compatible string (e.g. 1.00.a). However, the version just uses
semantic versioning so formatting the patch number as a character
is not correct and would result in printing control characters for
patch numbers less than 32.
Fixes: b1353d1c1d ("spi: Add Analog Devices AXI SPI Engine controller support")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20240412-axi-spi-engine-version-printf-v1-1-95e1e842c1a6@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f970ecb77 ]
This moves the message state in the AXI SPI Engine driver to a new
struct spi_engine_msg_state.
Previously, the driver state contained various pointers that pointed
to memory owned by a struct spi_message. However, it did not set any of
these pointers to NULL when a message was completed. This could lead to
use after free bugs.
Example of how this could happen:
1. SPI core calls into spi_engine_transfer_one_message() with msg1.
2. Assume something was misconfigured and spi_engine_tx_next() is not
called enough times in interrupt callbacks for msg1 such that
spi_engine->tx_xfer is never set to NULL before the msg1 completes.
3. SYNC interrupt is received and spi_finalize_current_message() is
called for msg1. spi_engine->msg is set to NULL but no other
message-specific state is reset.
4. Caller that sent msg1 is notified of the completion and frees msg1
and the associated xfers and tx/rx buffers.
4. SPI core calls into spi_engine_transfer_one_message() with msg2.
5. When spi_engine_tx_next() is called for msg2, spi_engine->tx_xfer is
still be pointing to an xfer from msg1, which was already freed.
spi_engine_xfer_next() tries to access xfer->transfer_list of one
of the freed xfers and we get a segfault or undefined behavior.
To avoid issues like this, instead of putting per-message state in the
driver state struct, we can make use of the struct spi_message::state
field to store a pointer to a new struct spi_engine_msg_state. This way,
all of the state that belongs to specific message stays with that
message and we don't have to remember to manually reset all aspects of
the message state when a message is completed. Rather, a new state is
allocated for each message.
Most of the changes are just renames where the state is accessed. One
place where this wasn't straightforward was the sync_id member. This
has been changed to use ida_alloc_range() since we needed to separate
the per-message sync_id from the per-controller next available sync_id.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20231117-axi-spi-engine-series-1-v1-9-cc59db999b87@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: 0064db9ce4 ("spi: axi-spi-engine: fix version format string")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e12cd96e8e ]
This modifies the AXI SPI Engine driver to use devm_spi_alloc_host()
instead of spi_alloc_host() to simplify the code a bit.
In addition to simplifying the error paths in the probe function, we
can also remove spi_controller_get/put() calls in the remove function
since devm_spi_alloc_host() sets a flag to no longer decrement the
controller reference count in the spi_unregister_controller() function.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20231117-axi-spi-engine-series-1-v1-4-cc59db999b87@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: 0064db9ce4 ("spi: axi-spi-engine: fix version format string")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a08199b309 ]
Since commit 7ef9651e97 ("clk: Provide new devm_clk helpers for prepared
and enabled clocks"), devm_clk_get() and clk_prepare_enable() can now be
replaced by devm_clk_get_enabled() when driver enables (and possibly
prepares) the clocks for the whole lifetime of the device. Moreover, it is
no longer necessary to unprepare and disable the clocks explicitly.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Link: https://lore.kernel.org/r/20230823133938.1359106-6-lizetao1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: 0064db9ce4 ("spi: axi-spi-engine: fix version format string")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 37eacb9f6e ]
Long ago a map file descriptor in a pseudo ldimm64 instruction could
only be present as an immediate value insn[0].imm, and thus this value
was used in a verbose verifier message printed when the file descriptor
wasn't valid. Since addition of BPF_PSEUDO_MAP_IDX_VALUE/BPF_PSEUDO_MAP_IDX
the insn[0].imm field can also contain an index pointing to the file
descriptor in the attr.fd_array array. However, if the file descriptor
is invalid, the verifier still prints the verbose message containing
value of insn[0].imm. Patch the verifier message to always print the
actual file descriptor value.
Fixes: 387544bfa2 ("bpf: Introduce fd_idx")
Signed-off-by: Anton Protopopov <aspsk@isovalent.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20240412141100.3562942-1-aspsk@isovalent.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0bc2e80b9b ]
Move the stray '.' that is currently at the end of the line after
newline '\n' to before newline character which is the right position.
Fixes: ce8d78616a ("nvme: warn about shared namespaces without CONFIG_NVME_MULTIPATH")
Signed-off-by: Yi Zhang <yi.zhang@redhat.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 70ee853eec ]
Add a regmap_read_bypassed() to allow reads from the hardware registers
while the regmap is in cache-only mode.
A typical use for this is to keep the cache in cache-only mode until
the hardware has reached a valid state, but one or more status registers
must be polled to determine when this state is reached.
For example, firmware download on the cs35l56 can take several seconds if
there are multiple amps sharing limited bus bandwidth. This is too long
to block in probe() so it is done as a background task. The device must
be soft-reset to reboot the firmware and during this time the registers are
not accessible, so the cache should be in cache-only. But the driver must
poll a register to detect when reboot has completed.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 8a731fd37f ("ASoC: cs35l56: Move utility functions to shared file")
Link: https://msgid.link/r/20240408101803.43183-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6648e61322 ]
Fix NULL pointer data-races in sk_psock_skb_ingress_enqueue() which
syzbot reported [1].
[1]
BUG: KCSAN: data-race in sk_psock_drop / sk_psock_skb_ingress_enqueue
write to 0xffff88814b3278b8 of 8 bytes by task 10724 on cpu 1:
sk_psock_stop_verdict net/core/skmsg.c:1257 [inline]
sk_psock_drop+0x13e/0x1f0 net/core/skmsg.c:843
sk_psock_put include/linux/skmsg.h:459 [inline]
sock_map_close+0x1a7/0x260 net/core/sock_map.c:1648
unix_release+0x4b/0x80 net/unix/af_unix.c:1048
__sock_release net/socket.c:659 [inline]
sock_close+0x68/0x150 net/socket.c:1421
__fput+0x2c1/0x660 fs/file_table.c:422
__fput_sync+0x44/0x60 fs/file_table.c:507
__do_sys_close fs/open.c:1556 [inline]
__se_sys_close+0x101/0x1b0 fs/open.c:1541
__x64_sys_close+0x1f/0x30 fs/open.c:1541
do_syscall_64+0xd3/0x1d0
entry_SYSCALL_64_after_hwframe+0x6d/0x75
read to 0xffff88814b3278b8 of 8 bytes by task 10713 on cpu 0:
sk_psock_data_ready include/linux/skmsg.h:464 [inline]
sk_psock_skb_ingress_enqueue+0x32d/0x390 net/core/skmsg.c:555
sk_psock_skb_ingress_self+0x185/0x1e0 net/core/skmsg.c:606
sk_psock_verdict_apply net/core/skmsg.c:1008 [inline]
sk_psock_verdict_recv+0x3e4/0x4a0 net/core/skmsg.c:1202
unix_read_skb net/unix/af_unix.c:2546 [inline]
unix_stream_read_skb+0x9e/0xf0 net/unix/af_unix.c:2682
sk_psock_verdict_data_ready+0x77/0x220 net/core/skmsg.c:1223
unix_stream_sendmsg+0x527/0x860 net/unix/af_unix.c:2339
sock_sendmsg_nosec net/socket.c:730 [inline]
__sock_sendmsg+0x140/0x180 net/socket.c:745
____sys_sendmsg+0x312/0x410 net/socket.c:2584
___sys_sendmsg net/socket.c:2638 [inline]
__sys_sendmsg+0x1e9/0x280 net/socket.c:2667
__do_sys_sendmsg net/socket.c:2676 [inline]
__se_sys_sendmsg net/socket.c:2674 [inline]
__x64_sys_sendmsg+0x46/0x50 net/socket.c:2674
do_syscall_64+0xd3/0x1d0
entry_SYSCALL_64_after_hwframe+0x6d/0x75
value changed: 0xffffffff83d7feb0 -> 0x0000000000000000
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 10713 Comm: syz-executor.4 Tainted: G W 6.8.0-syzkaller-08951-gfe46a7dd189e #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 02/29/2024
Prior to this, commit 4cd12c6065 ("bpf, sockmap: Fix NULL pointer
dereference in sk_psock_verdict_data_ready()") fixed one NULL pointer
similarly due to no protection of saved_data_ready. Here is another
different caller causing the same issue because of the same reason. So
we should protect it with sk_callback_lock read lock because the writer
side in the sk_psock_drop() uses "write_lock_bh(&sk->sk_callback_lock);".
To avoid errors that could happen in future, I move those two pairs of
lock into the sk_psock_data_ready(), which is suggested by John Fastabend.
Fixes: 604326b41a ("bpf, sockmap: convert to generic sk_msg interface")
Reported-by: syzbot+aa8c8ec2538929f18f2d@syzkaller.appspotmail.com
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Closes: https://syzkaller.appspot.com/bug?extid=aa8c8ec2538929f18f2d
Link: https://lore.kernel.org/all/20240329134037.92124-1-kerneljasonxing@gmail.com
Link: https://lore.kernel.org/bpf/20240404021001.94815-1-kerneljasonxing@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff33132605 ]
The devm_regulator_get_enable_optional() should be a 'call and forget'
API, meaning, when it is used to enable the regulators, the API does not
provide a handle to do any further control of the regulators. It gives
no real benefit to return an error from the stub if CONFIG_REGULATOR is
not set.
On the contrary, returning an error is causing problems to drivers when
hardware is such it works out just fine with no regulator control.
Returning an error forces drivers to specifically handle the case where
CONFIG_REGULATOR is not set, making the mere existence of the stub
questionalble.
Change the stub implementation for the
devm_regulator_get_enable_optional() to return Ok so drivers do not
separately handle the case where the CONFIG_REGULATOR is not set.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Fixes: da279e6965 ("regulator: Add devm helpers for get and enable")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/ZiedtOE00Zozd3XO@fedora
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 96e20adc43 ]
The devm_regulator_get_enable() should be a 'call and forget' API,
meaning, when it is used to enable the regulators, the API does not
provide a handle to do any further control of the regulators. It gives
no real benefit to return an error from the stub if CONFIG_REGULATOR is
not set.
On the contrary, returning and error is causing problems to drivers when
hardware is such it works out just fine with no regulator control.
Returning an error forces drivers to specifically handle the case where
CONFIG_REGULATOR is not set, making the mere existence of the stub
questionalble. Furthermore, the stub of the regulator_enable() seems to
be returning Ok.
Change the stub implementation for the devm_regulator_get_enable() to
return Ok so drivers do not separately handle the case where the
CONFIG_REGULATOR is not set.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reported-by: Aleksander Mazur <deweloper@wp.pl>
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Fixes: da279e6965 ("regulator: Add devm helpers for get and enable")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/ZiYF6d1V1vSPcsJS@drtxq0yyyyyyyyyyyyyby-3.rev.dnainternet.fi
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3cf8a1749 ]
The MT6360 regulator binding, the example in the MT6360 mfd binding, and
the devicetree users of those bindings are rightfully declaring MT6360
regulator subnodes with non-capital names, and luckily without using the
deprecated regulator-compatible property.
With this driver declaring capitalized BUCKx/LDOx as of_match string for
the node names, obviously no regulator gets probed: fix that by changing
the MT6360_REGULATOR_DESC macro to add a "match" parameter which gets
assigned to the of_match.
Fixes: d321571d5e ("regulator: mt6360: Add support for MT6360 regulator")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://msgid.link/r/20240409144438.410060-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e0fb11364 ]
The of_match shall correspond to the name of the regulator subnode,
or the deprecated `regulator-compatible` property must be used:
failing to do so, the regulator won't probe (and the driver will
as well not probe).
Since the devicetree binding for this driver is actually correct
and wants DTs to use the "usb-otg-vbus-regulator" subnode name,
fix this driver by aligning the `of_match` string to what the DT
binding wants.
Fixes: 0402e8ebb8 ("power: supply: mt6360_charger: add MT6360 charger support")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20240410084405.1389378-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 452d8950db ]
The rt9455_boost_voltage_values[] array is only used when USB PHY
support is enabled, causing a W=1 warning otherwise:
drivers/power/supply/rt9455_charger.c:200:18: error: 'rt9455_boost_voltage_values' defined but not used [-Werror=unused-const-variable=]
Enclose the definition in the same #ifdef as the references to it.
Fixes: e86d69dd78 ("power_supply: Add support for Richtek RT9455 battery charger")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240403080702.3509288-10-arnd@kernel.org
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fed6d9a8e6 ]
For all the "score" pin-groups all the intel_pingroup-s to select
the non GPIO function are re-used for byt_score_gpio_groups[].
But this is incorrect since a pin-group includes the mode setting,
which for the non GPIO functions generally is 1, where as to select
the GPIO function mode must be set to 0.
So the GPIO function needs separate intel_pingroup-s with their own mode
value of 0.
Add a new PIN_GROUP_GPIO macro which adds a foo_gpio entry to each
pin-group defined this way and update byt_score_gpio_groups[] to point
to the new foo_gpio entries.
The "sus" usb_oc_grp usb_ulpi_grp and pcu_spi_grp pin-groups are special
because these have a non 0 mode value to select the GPIO functions and
these already have matching foo_gpio pin-groups, leave these are unchanged.
The pmu_clk "sus" groups added in commit 2f46d7f7e9 ("pinctrl: baytrail:
Add pinconf group + function for the pmu_clk") do need to use the new
PIN_GROUP_GPIO macro.
Fixes: 2f46d7f7e9 ("pinctrl: baytrail: Add pinconf group + function for the pmu_clk")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1548036ef1 ]
Now that we're exposing the rpc stats on a per-network namespace basis,
move this struct into struct nfs_net and use that to make sure only the
per-network namespace stats are exposed.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Stable-dep-of: 24457f1be2 ("nfs: Handle error of rpc_proc_register() in nfs_net_init().")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d47151b79e ]
We're using nfs mounts inside of containers in production and noticed
that the nfs stats are not exposed in /proc. This is a problem for us
as we use these stats for monitoring, and have to do this awkward bind
mount from the main host into the container in order to get to these
states.
Add the rpc_proc_register call to the pernet operations entry and exit
points so these stats can be exposed inside of network namespaces.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Stable-dep-of: 24457f1be2 ("nfs: Handle error of rpc_proc_register() in nfs_net_init().")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2057a48d0d ]
We want to be able to have our rpc stats handled in a per network
namespace manner, so add an option to rpc_create_args to specify a
different rpc_stats struct instead of using the one on the rpc_program.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Stable-dep-of: 24457f1be2 ("nfs: Handle error of rpc_proc_register() in nfs_net_init().")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c5d3b64c56 ]
There is a misinterpretation of some of the PIN_CONFIG_* options in this
driver library. PIN_CONFIG_OUTPUT_ENABLE should refer to a buffer or
switch in the output direction of the electrical path. The MediaTek
hardware does not have such a thing. The driver incorrectly maps this
option to the GPIO function's direction.
Likewise, PIN_CONFIG_INPUT_ENABLE should refer to a buffer or switch in
the input direction. The hardware does have such a mechanism, and is
mapped to the IES bit. The driver however sets the direction in addition
to the IES bit, which is incorrect. On readback, the IES bit isn't even
considered.
Ironically, the driver does not support readback for PIN_CONFIG_OUTPUT,
while its readback of PIN_CONFIG_{INPUT,OUTPUT}_ENABLE is what it should
be doing for PIN_CONFIG_OUTPUT.
Rework support for these three options, so that PIN_CONFIG_OUTPUT_ENABLE
is completely removed, PIN_CONFIG_INPUT_ENABLE is only linked to the IES
bit, and PIN_CONFIG_OUTPUT is linked to the GPIO function's direction
and output level.
Fixes: 805250982b ("pinctrl: mediatek: add pinctrl-paris that implements the vendor dt-bindings")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Message-ID: <20240327091336.3434141-3-wenst@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08f66a8edd ]
In the generic pin config library, readback of some options are handled
differently compared to the setting of those options: the argument value
is used to convey enable/disable of an option in the set path, but
success or -EINVAL is used to convey if an option is enabled or disabled
in the debugfs readback path.
PIN_CONFIG_INPUT_SCHMITT_ENABLE is one such option. Fix the readback of
the option in the mediatek-paris library, so that the debugfs dump is
not showing "input schmitt enabled" for pins that don't have it enabled.
Fixes: 1bea6afbc8 ("pinctrl: mediatek: Refine mtk_pinconf_get()")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Message-ID: <20240327091336.3434141-2-wenst@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5038a66dad ]
The "pctldev" struct is allocated in devm_pinctrl_register_and_init().
It's a devm_ managed pointer that is freed by devm_pinctrl_dev_release(),
so freeing it in pinctrl_enable() will lead to a double free.
The devm_pinctrl_dev_release() function frees the pindescs and destroys
the mutex as well.
Fixes: 6118714275 ("pinctrl: core: Fix pinctrl_register_and_init() with pinctrl_enable()")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Message-ID: <578fbe56-44e9-487c-ae95-29b695650f7c@moroto.mountain>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7f8dedb4b ]
This patch adds support for QCA2066 firmware patch and NVM downloading.
as the RF performance of QCA2066 SOC chip from different foundries may
vary. Therefore we use different NVM to configure them based on board ID.
Changes in v2
- optimize the function qca_generate_hsp_nvm_name
- remove redundant debug code for function qca_read_fw_board_id
Signed-off-by: Tim Jiang <quic_tjiang@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Stable-dep-of: 32868e126c ("Bluetooth: qca: fix invalid device address check")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit caba40ec35 ]
The DDR3 SPD data structure advertises the presence of a thermal
sensor on a DDR3 module in byte 32, bit 7. Let's use this information
to explicitly instantiate the thermal sensor I2C client instead of
having to rely on class-based I2C probing.
The temp sensor i2c address can be derived from the SPD i2c address,
so we can directly instantiate the device and don't have to probe
for it. If the temp sensor has been instantiated already by other
means (e.g. class-based auto-detection), then the busy-check in
i2c_new_client_device will detect this.
Note: Thermal sensors on DDR4 DIMM's are instantiated from the
ee1004 driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/68113672-3724-44d5-9ff8-313dd6628f8c@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: f42c97027f ("eeprom: at24: fix memory corruption race condition")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7044dcff83 ]
The `module!` macro creates glue code that are called by C to initialize
the Rust modules using the `Module::init` function. Part of this glue
code are the local functions `__init` and `__exit` that are used to
initialize/destroy the Rust module.
These functions are safe and also visible to the Rust mod in which the
`module!` macro is invoked. This means that they can be called by other
safe Rust code. But since they contain `unsafe` blocks that rely on only
being called at the right time, this is a soundness issue.
Wrap these generated functions inside of two private modules, this
guarantees that the public functions cannot be called from the outside.
Make the safe functions `unsafe` and add SAFETY comments.
Cc: stable@vger.kernel.org
Reported-by: Björn Roy Baron <bjorn3_gh@protonmail.com>
Closes: https://github.com/Rust-for-Linux/linux/issues/629
Fixes: 1fbde52bde ("rust: add `macros` crate")
Signed-off-by: Benno Lossin <benno.lossin@proton.me>
Reviewed-by: Wedson Almeida Filho <walmeida@microsoft.com>
Link: https://lore.kernel.org/r/20240401185222.12015-1-benno.lossin@proton.me
[ Moved `THIS_MODULE` out of the private-in-private modules since it
should remain public, as Dirk Behme noticed [1]. Capitalized comments,
avoided newline in non-list SAFETY comments and reworded to add
Reported-by and newline. ]
Link: https://rust-for-linux.zulipchat.com/#narrow/stream/291565-Help/topic/x/near/433512583 [1]
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b6170ff7a ]
Currently Rust kernel modules have their init code placed in the `.text`
section of the .ko file. I don't think this causes any real problems
for Rust modules as long as all code called during initialization lives
in `.text`.
However, if a Rust `init_module()` function (that lives in `.text`)
calls a function marked with `__init` (in C) or
`#[link_section = ".init.text"]` (in Rust), then a warning is
generated by modpost because that function lives in `.init.text`.
For example:
WARNING: modpost: fs/bcachefs/bcachefs: section mismatch in reference: init_module+0x6 (section: .text) -> _RNvXCsj7d3tFpT5JS_15bcachefs_moduleNtB2_8BcachefsNtCsjDtqRIL3JAG_6kernel6Module4init (section: .init.text)
I ran into this while experimenting with converting the bcachefs kernel
module from C to Rust. The module's `init()`, written in Rust, calls C
functions like `bch2_vfs_init()` which are placed in `.init.text`.
This patch places the macro-generated `init_module()` Rust function in
the `.init.text` section. It also marks `init_module()` as unsafe--now
it may not be called after module initialization completes because it
may be freed already.
Note that this is not enough on its own to actually get all the module
initialization code in that section. The module author must still add
the `#[link_section = ".init.text"]` attribute to the Rust `init()` in
the `impl kernel::Module` block in order to then call `__init`
functions. However, this patch enables module authors do so, when
previously it would not be possible (without warnings).
Signed-off-by: Thomas Bertschinger <tahbertschinger@gmail.com>
Reviewed-by: Martin Rodriguez Reboredo <yakoyoku@gmail.com>
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Link: https://lore.kernel.org/r/20240206153806.567055-1-tahbertschinger@gmail.com
[ Reworded title to add prefix. ]
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Stable-dep-of: 7044dcff83 ("rust: macros: fix soundness issue in `module!` macro")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d2d73a6dd1 ]
MTD OTP logic is very fragile on parsing NVMEM cell and can be
problematic with some specific kind of devices.
The problem was discovered by e87161321a ("mtd: rawnand: macronix:
OTP access for MX30LFxG18AC") where OTP support was added to a NAND
device. With the case of NAND devices, it does require a node where ECC
info are declared and all the fixed partitions, and this cause the OTP
codepath to parse this node as OTP NVMEM cells, making probe fail and
the NAND device registration fail.
MTD OTP parsing should have been limited to always using compatible to
prevent this error by using node with compatible "otp-user" or
"otp-factory".
NVMEM across the years had various iteration on how cells could be
declared in DT, in some old implementation, no_of_node should have been
enabled but now add_legacy_fixed_of_cells should be used to disable
NVMEM to parse child node as NVMEM cell.
To fix this and limit any regression with other MTD that makes use of
declaring OTP as direct child of the dev node, disable
add_legacy_fixed_of_cells if we detect the MTD type is Nand.
With the following logic, the OTP NVMEM entry is correctly created with
no cells and the MTD Nand is correctly probed and partitions are
correctly exposed.
Fixes: 4b361cfa86 ("mtd: core: add OTP nvmem provider support")
Cc: <stable@vger.kernel.org> # v6.7+
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240412105030.1598-1-ansuelsmth@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2cc3b37f5b ]
Binding for fixed NVMEM cells defined directly as NVMEM device subnodes
has been deprecated. It has been replaced by the "fixed-layout" NVMEM
layout binding.
New syntax is meant to be clearer and should help avoiding imprecise
bindings.
NVMEM subsystem already supports the new binding. It should be a good
idea to limit support for old syntax to existing drivers that actually
support & use it (we can't break backward compatibility!). That way we
additionally encourage new bindings & drivers to ignore deprecated
binding.
It wasn't clear (to me) if rtc and w1 code actually uses old syntax
fixed cells. I enabled them to don't risk any breakage.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
[for meson-{efuse,mx-efuse}.c]
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
[for mtk-efuse.c, nvmem/core.c, nvmem-provider.h]
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
[MT8192, MT8195 Chromebooks]
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
[for microchip-otpc.c]
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
[SAMA7G5-EK]
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20231020105545.216052-3-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: d2d73a6dd1 ("mtd: limit OTP NVMEM cell parse to non-NAND devices")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit afc89870ea ]
This reverts commit 22a9d95858 ("dmaengine: pl330: issue_pending waits
until WFP state") as it seems to cause regression in pl330 driver.
Note the issue now exists in mainline so a fix to be done.
Cc: stable@vger.kernel.org
Reported-by: karthikeyan <karthikeyan@linumiz.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
noints mode disables 2 fragments that configure a GPIO to
be used for the interrupt line from the MCP23017, but fails
to remove the pinctrl-0 reference or pinctrl-names.
It therefore fails to load due to an invalid phandle.
Move the pinctrl-0 and pinctrl-names properties so they
also get disabled by the noints override.
https://forums.raspberrypi.com/viewtopic.php?t=370907
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
If PCIE1 is left with the default (zero) AXI QoS values, endpoints can
receive extremely poor service for non-posted transactions e.g. reads.
Such transactions can take milliseconds to complete on a contended
system.
Bump priorities for every TC above the non-realtime greedy peripherals
in BCM2712, to allow reasonable service without competing against hard
realtime peripherals.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
For video encoding, if the framerate was set after the component
was created, then it wasn't set correctly on the port, and an
old value was encoded in the bitstream.
Update the port status when the framerate is set.
https://github.com/raspberrypi/rpicam-apps/issues/664
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Even when configured to use only gpiod CS lines, the DW SPI controller
still expects a bit to be set in the SER register, otherwise transfers
stall. For the csgpiod case, nominate bit 0 for the job.
See: https://github.com/raspberrypi/linux/issues/6159
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The firmware needs 16 pixel alignment on RGBx 32bpp formats, which
would be 64 byte. The driver was only setting 32byte alignment.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
vc4_disable_vblank assumed that vc4_encoder was always assigned,
which isn't guaranteed.
If it isn't assigned then disable the interrupt anyway as it's
not connected.
https://github.com/raspberrypi/linux/issues/6146
Fixes: 63c0bcc4b7 ("drm/vc4: Add option to call from crtc to encoder on vblank")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Following the adoption upstream of a similar parameter but with another
name, update the dtparam definitions to use the new name and sense.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
commit 8ff05989b4 upstream.
Until now after a bcm2835 pin was freed its pinmux was set to GPIO_IN.
So in case it was configured as GPIO_OUT before the configured output
level also get lost. As long as GPIO sysfs was used this wasn't
actually a problem because the pins and their possible output level
were kept by sysfs.
Since more and more Raspberry Pi users start using libgpiod they are
confused about this behavior. So make the pin freeing behavior of
GPIO_OUT configurable via module parameter. In case
pinctrl-bcm2835.persist_gpio_outputs is set to 1, the output level is
kept.
This patch based on the downstream work of Phil Elwell.
Link: https://github.com/raspberrypi/linux/pull/6117
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Message-ID: <20240503062745.11298-1-wahrenst@gmx.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
commit 475747a193 upstream.
Omit rx_use_md_dst comment in upstream commit since macsec_ops is not
documented.
Cannot know whether a Rx skb missing md_dst is intended for MACsec or not
without knowing whether the device is able to update this field during an
offload. Assume that an offload to a MACsec device cannot support updating
md_dst by default. Capable devices can advertise that they do indicate that
an skb is related to a MACsec offloaded packet using the md_dst.
Cc: Sabrina Dubroca <sd@queasysnail.net>
Cc: stable@vger.kernel.org
Fixes: 860ead89b8 ("net/macsec: Add MACsec skb_metadata_dst Rx Data path support")
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Benjamin Poirier <bpoirier@nvidia.com>
Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://lore.kernel.org/r/20240423181319.115860-2-rrameshbabu@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 1d6cd2146c which was
mistakenly added into v6.6.y and the commit corresponding to the 'Fixes:'
tag is invalid. For more information, see link [1].
This will result in the loss of Crashkernel data in /proc/iomem, and kdump
failed:
```
Memory for crashkernel is not reserved
Please reserve memory by passing"crashkernel=Y@X" parameter to kernel
Then try to loading kdump kernel
```
After revert, kdump works fine. Tested on QEMU riscv.
Link: https://lore.kernel.org/linux-riscv/ZSiQRDGLZk7lpakE@MiWiFi-R3L-srv [1]
Cc: Baoquan He <bhe@redhat.com>
Cc: Chen Jiahao <chenjiahao16@huawei.com>
Signed-off-by: Mingzheng Xing <xingmingzheng@iscas.ac.cn>
Acked-by: Baoquan He <bhe@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bf6e4ee5c4 ]
The power_supply frame-work is not really designed for there to be
long living in kernel references to power_supply devices.
Specifically unregistering a power_supply while some other code has
a reference to it triggers a WARN in power_supply_unregister():
WARN_ON(atomic_dec_return(&psy->use_cnt));
Folllowed by the power_supply still getting removed and the
backing data freed anyway, leaving the tusb1210 charger-detect code
with a dangling reference, resulting in a crash the next time
tusb1210_get_online() is called.
Fix this by only holding the reference in tusb1210_get_online()
freeing it at the end of the function. Note this still leaves
a theoretical race window, but it avoids the issue when manually
rmmod-ing the charger chip driver during development.
Fixes: 48969a5623 ("phy: ti: tusb1210: Add charger detection")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240406140821.18624-1-hdegoede@redhat.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aea702dde7 ]
commit 3335068f87 ("riscv: Use PUD/P4D/PGD pages for the linear
mapping") added logic to allow using RAM below the kernel load address.
However, this does not work for NOMMU, where PAGE_OFFSET is fixed to the
kernel load address. Since that range of memory corresponds to PFNs
below ARCH_PFN_OFFSET, mm initialization runs off the beginning of
mem_map and corrupts adjacent kernel memory. Fix this by restoring the
previous behavior for NOMMU kernels.
Fixes: 3335068f87 ("riscv: Use PUD/P4D/PGD pages for the linear mapping")
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Link: https://lore.kernel.org/r/20240227003630.3634533-3-samuel.holland@sifive.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac88ff6b9d ]
When below config items are set, compiler complained:
--------------------
CONFIG_CRASH_CORE=y
CONFIG_KEXEC_CORE=y
CONFIG_CRASH_DUMP=y
......
-----------------------
-------------------------------------------------------------------
arch/riscv/kernel/crash_core.c: In function 'arch_crash_save_vmcoreinfo':
arch/riscv/kernel/crash_core.c:11:58: warning: format '%lx' expects argument of type 'long unsigned int', but argument 2 has type 'int' [-Wformat=]
11 | vmcoreinfo_append_str("NUMBER(VMALLOC_START)=0x%lx\n", VMALLOC_START);
| ~~^
| |
| long unsigned int
| %x
----------------------------------------------------------------------
This is because on riscv macro VMALLOC_START has different type when
CONFIG_MMU is set or unset.
arch/riscv/include/asm/pgtable.h:
--------------------------------------------------
Changing it to _AC(0, UL) in case CONFIG_MMU=n can fix the warning.
Link: https://lkml.kernel.org/r/ZW7OsX4zQRA3mO4+@MiWiFi-R3L-srv
Signed-off-by: Baoquan He <bhe@redhat.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Cc: Eric DeVolder <eric_devolder@yahoo.com>
Cc: Ignat Korchagin <ignat@cloudflare.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Stable-dep-of: 6065e736f8 ("riscv: Fix TASK_SIZE on 64-bit NOMMU")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f221033f5c ]
During the removal of the idxd driver, registered offline callback is
invoked as part of the clean up process. However, on systems with only
one CPU online, no valid target is available to migrate the
perf context, resulting in a kernel oops:
BUG: unable to handle page fault for address: 000000000002a2b8
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
PGD 1470e1067 P4D 0
Oops: 0002 [#1] PREEMPT SMP NOPTI
CPU: 0 PID: 20 Comm: cpuhp/0 Not tainted 6.8.0-rc6-dsa+ #57
Hardware name: Intel Corporation AvenueCity/AvenueCity, BIOS BHSDCRB1.86B.2492.D03.2307181620 07/18/2023
RIP: 0010:mutex_lock+0x2e/0x50
...
Call Trace:
<TASK>
__die+0x24/0x70
page_fault_oops+0x82/0x160
do_user_addr_fault+0x65/0x6b0
__pfx___rdmsr_safe_on_cpu+0x10/0x10
exc_page_fault+0x7d/0x170
asm_exc_page_fault+0x26/0x30
mutex_lock+0x2e/0x50
mutex_lock+0x1e/0x50
perf_pmu_migrate_context+0x87/0x1f0
perf_event_cpu_offline+0x76/0x90 [idxd]
cpuhp_invoke_callback+0xa2/0x4f0
__pfx_perf_event_cpu_offline+0x10/0x10 [idxd]
cpuhp_thread_fun+0x98/0x150
smpboot_thread_fn+0x27/0x260
smpboot_thread_fn+0x1af/0x260
__pfx_smpboot_thread_fn+0x10/0x10
kthread+0x103/0x140
__pfx_kthread+0x10/0x10
ret_from_fork+0x31/0x50
__pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1b/0x30
<TASK>
Fix the issue by preventing the migration of the perf context to an
invalid target.
Fixes: 81dd4d4d61 ("dmaengine: idxd: Add IDXD performance monitor support")
Reported-by: Terrence Xu <terrence.xu@intel.com>
Tested-by: Terrence Xu <terrence.xu@intel.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Link: https://lore.kernel.org/r/20240313214031.1658045-1-fenghua.yu@intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5638de827 ]
drain_workqueue() cannot be called safely in a spinlocked context due to
possible task rescheduling. In the multi-task scenario, calling
queue_work() while drain_workqueue() will lead to a Call Trace as
pushing a work on a draining workqueue is not permitted in spinlocked
context.
Call Trace:
<TASK>
? __warn+0x7d/0x140
? __queue_work+0x2b2/0x440
? report_bug+0x1f8/0x200
? handle_bug+0x3c/0x70
? exc_invalid_op+0x18/0x70
? asm_exc_invalid_op+0x1a/0x20
? __queue_work+0x2b2/0x440
queue_work_on+0x28/0x30
idxd_misc_thread+0x303/0x5a0 [idxd]
? __schedule+0x369/0xb40
? __pfx_irq_thread_fn+0x10/0x10
? irq_thread+0xbc/0x1b0
irq_thread_fn+0x21/0x70
irq_thread+0x102/0x1b0
? preempt_count_add+0x74/0xa0
? __pfx_irq_thread_dtor+0x10/0x10
? __pfx_irq_thread+0x10/0x10
kthread+0x103/0x140
? __pfx_kthread+0x10/0x10
ret_from_fork+0x31/0x50
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1b/0x30
</TASK>
The current implementation uses a spinlock to protect event log workqueue
and will lead to the Call Trace due to potential task rescheduling.
To address the locking issue, convert the spinlock to mutex, allowing
the drain_workqueue() to be called in a safe mutex-locked context.
This change ensures proper synchronization when accessing the event log
workqueue, preventing potential Call Trace and improving the overall
robustness of the code.
Fixes: c40bd7d973 ("dmaengine: idxd: process user page faults for completion record")
Signed-off-by: Rex Zhang <rex.zhang@intel.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Fenghua Yu <fenghua.yu@intel.com>
Reviewed-by: Lijun Pan <lijun.pan@intel.com>
Link: https://lore.kernel.org/r/20240404223949.2885604-1-fenghua.yu@intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 47b3e2f391 ]
According to the 'qcom,ipq5332-usb-hsphy.yaml' schema, the 5V
supply regulator must be defined via the 'vdd-supply' property.
The driver however requests for the 'vdda-phy' regulator which
results in the following message when the driver is probed on
a IPQ5018 based board with a device tree matching to the schema:
qcom-m31usb-phy 5b000.phy: supply vdda-phy not found, using dummy regulator
qcom-m31usb-phy 5b000.phy: Registered M31 USB phy
This means that the regulator specified in the device tree never
gets enabled.
Change the driver to use the 'vdd' name for the regulator as per
defined in the schema in order to ensure that the corresponding
regulator gets enabled.
Fixes: 08e49af507 ("phy: qcom: Introduce M31 USB PHY driver")
Reviewed-by: Varadarajan Narayanan <quic_varada@quicinc.com>
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240406-phy-qcom-m31-regulator-fix-v2-1-c8e9795bc071@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d16d4002fe ]
The pcie1l0_sel and pcie1l1_sel bits in PCIESEL_CON configure the
mux for PCIe1L0 and PCIe1L1 to either the PIPE Combo PHYs or the
PCIe3 PHY. Thus this configuration interfers with the data-lanes
configuration done by the PCIe3 PHY.
RK3588 has three Combo PHYs. The first one has a dedicated PCIe
controller and is not affected by this. For the other two Combo
PHYs, there is one mux for each of them.
pcie1l0_sel selects if PCIe 1L0 is muxed to Combo PHY 1 when
bit is set to 0 or to the PCIe3 PHY when bit is set to 1.
pcie1l1_sel selects if PCIe 1L1 is muxed to Combo PHY 2 when
bit is set to 0 or to the PCIe3 PHY when bit is set to 1.
Currently the code always muxes 1L0 and 1L1 to the Combi PHYs
once one of them is being used in PCIe mode. This is obviously
wrong when at least one of the ports should be muxed to the
PCIe3 PHY.
Fix this by introducing Combo PHY identification and then only
setting up the required bit.
Fixes: a03c442772 ("phy: rockchip: Add naneng combo phy support for RK3588")
Reported-by: Michal Tomek <mtdev79b@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20240404-rk3588-pcie-bifurcation-fixes-v1-3-9907136eeafd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f8020dfb31 ]
So far all RK3588 boards use fully aggregated PCIe. CM3588 is one
of the few boards using this feature and apparently it is broken.
The PHY offers the following mapping options:
port 0 lane 0 - always mapped to controller 0 (4L)
port 0 lane 1 - to controller 0 or 2 (1L0)
port 1 lane 0 - to controller 0 or 1 (2L)
port 1 lane 1 - to controller 0, 1 or 3 (1L1)
The data-lanes DT property maps these as follows:
0 = no controller (unsupported by the HW)
1 = 4L
2 = 2L
3 = 1L0
4 = 1L1
That allows the following configurations with first column being the
mainline data-lane mapping, second column being the downstream name,
third column being PCIE3PHY_GRF_CMN_CON0 and PHP_GRF_PCIESEL register
values and final column being the user visible lane setup:
<1 1 1 1> = AGGREG = [4 0] = x4 (aggregation)
<1 1 2 2> = NANBNB = [0 0] = x2 x2 (no bif.)
<1 3 2 2> = NANBBI = [1 1] = x2 x1x1 (bif. of port 0)
<1 1 2 4> = NABINB = [2 2] = x1x1 x2 (bif. of port 1)
<1 3 2 4> = NABIBI = [3 3] = x1x1 x1x1 (bif. of both ports)
The driver currently does not program PHP_GRF_PCIESEL correctly, which
is fixed by this patch. As a side-effect the new logic is much simpler
than the old logic.
Fixes: 2e9bffc4f7 ("phy: rockchip: Support PCIe v3")
Signed-off-by: Michal Tomek <mtdev79b@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20240404-rk3588-pcie-bifurcation-fixes-v1-1-9907136eeafd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e4308bc22b ]
There is an out of bounds read access of 'gbe_phy_init_fix[fix_idx].addr'
every iteration after 'fix_idx' reaches 'ARRAY_SIZE(gbe_phy_init_fix)'.
Make sure 'gbe_phy_init[addr]' is used when all elements of
'gbe_phy_init_fix' array are handled.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 934337080c ("phy: marvell: phy-mvebu-a3700-comphy: Add native kernel implementation")
Signed-off-by: Mikhail Kobuk <m.kobuk@ispras.ru>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20240321164734.49273-1-m.kobuk@ispras.ru
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63dc588e7a ]
When SoundWire Wake interrupt is enabled along with SoundWire Wake
enable register, SoundWire wake interrupt will be reported
when SoundWire manager is in D3 state and ACP is in D3 state.
When SoundWire Wake interrupt is reported, it will invoke runtime
resume of the SoundWire manager device.
In case of system level suspend, for ClockStop Mode SoundWire Wake
interrupt should be disabled.
It should be enabled only for runtime suspend scenario.
Change wake interrupt enable/disable sequence for ClockStop Mode in
system level suspend and runtime suspend sceanrio.
Fixes: 9cf1efc5ed ("soundwire: amd: add pm_prepare callback and pm ops support")
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20240327063143.2266464-2-Vijendar.Mukunda@amd.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 30f0ced997 ]
The existing residual calculation returns an incorrect value when
bytes_xfer == bytes_req. This scenario occurs particularly with drivers
like UART where DMA is scheduled for maximum number of bytes and is
terminated when the bytes inflow stops. At higher baud rates, it could
request the tx_status while there is no bytes left to transfer. This will
lead to incorrect residual being set. Hence return residual as '0' when
bytes transferred equals to the bytes requested.
Fixes: ee17028009 ("dmaengine: tegra: Add tegra gpcdma driver")
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20240315124411.17582-1-akhilrajeev@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43c633ef93 ]
When building with 'make W=1', clang notices that the computed register
values are never actually written back but instead the wrong variable
is set:
drivers/dma/owl-dma.c:244:6: error: variable 'regval' set but not used [-Werror,-Wunused-but-set-variable]
244 | u32 regval;
| ^
drivers/dma/owl-dma.c:268:6: error: variable 'regval' set but not used [-Werror,-Wunused-but-set-variable]
268 | u32 regval;
| ^
Change these to what was most likely intended.
Fixes: 47e20577c2 ("dmaengine: Add Actions Semi Owl family S900 DMA driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Peter Korsgaard <peter@korsgaard.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240322132116.906475-1-arnd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5abed58a8b upstream.
Commit ec17373aeb ("phy: qcom: qmp-combo: extract common function to
setup clocks") changed the offset that is used to write to
DP_PHY_VCO_DIV from QSERDES_V3_DP_PHY_VCO_DIV to
QSERDES_V4_DP_PHY_VCO_DIV. Unfortunately, this offset is different
between v3 and v4 phys:
#define QSERDES_V3_DP_PHY_VCO_DIV 0x064
#define QSERDES_V4_DP_PHY_VCO_DIV 0x070
meaning that we write the wrong register on v3 phys now. Add another
generic register to 'regs' and use it here instead of a version specific
define to fix this.
This was discovered after Abhinav looked over register dumps with me
from sc7180 Trogdor devices that started failing to light up the
external display with v6.6 based kernels. It turns out that some
monitors are very specific about their link clk frequency and if the
default power on reset value is still there the monitor will show a
blank screen or a garbled display. Other monitors are perfectly happy to
get a bad clock signal.
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Abhinav Kumar <quic_abhinavk@quicinc.com>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: ec17373aeb ("phy: qcom: qmp-combo: extract common function to setup clocks")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240404234345.1446300-1-swboyd@chromium.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 21c9fb611c upstream.
I ran into a randconfig build failure with UBSAN using gcc-13.2:
arm-linux-gnueabi-ld: error: unplaced orphan section `.bss..Lubsan_data31' from `drivers/mtd/nand/raw/diskonchip.o'
I'm not entirely sure what is going on here, but I suspect this has something
to do with the check for the end of the doc_locations[] array that contains
an (unsigned long)0xffffffff element, which is compared against the signed
(int)0xffffffff. If this is the case, we should get a runtime check for
undefined behavior, but we instead get an unexpected build-time error.
I would have expected this to work fine on 32-bit architectures despite the
signed integer overflow, though on 64-bit architectures this likely won't
ever work.
Changing the contition to instead check for the size of the array makes the
code safe everywhere and avoids the ubsan check that leads to the link
error. The loop code goes back to before 2.6.12.
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240405143015.717429-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 78d9161d2b upstream.
With deferred IO enabled, a page fault happens when data is written to the
framebuffer device. Then driver determines which page is being updated by
calculating the offset of the written virtual address within the virtual
memory area, and uses this offset to get the updated page within the
internal buffer. This page is later copied to hardware (thus the name
"deferred IO").
This offset calculation is only correct if the virtual memory area is
mapped to the beginning of the internal buffer. Otherwise this is wrong.
For example, if users do:
mmap(ptr, 4096, PROT_WRITE, MAP_FIXED | MAP_SHARED, fd, 0xff000);
Then the virtual memory area will mapped at offset 0xff000 within the
internal buffer. This offset 0xff000 is not accounted for, and wrong page
is updated.
Correct the calculation by using vmf->pgoff instead. With this change, the
variable "offset" will no longer hold the exact offset value, but it is
rounded down to multiples of PAGE_SIZE. But this is still correct, because
this variable is only used to calculate the page offset.
Reported-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Closes: https://lore.kernel.org/linux-fbdev/271372d6-e665-4e7f-b088-dee5f4ab341a@oracle.com
Fixes: 56c134f7f1 ("fbdev: Track deferred-I/O pages in pageref struct")
Cc: <stable@vger.kernel.org>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20240423115053.4490-1-namcao@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f489c94802 upstream.
commit 2f4a4d63a1 ("ACPI: CPPC: Use access_width over bit_width for system
memory accesses") modified cpc_read()/cpc_write() to use access_width to
read CPC registers.
However, for PCC registers the access width field in the ACPI register
macro specifies the PCC subspace ID. For non-zero PCC subspace ID it is
incorrectly treated as access width. This causes errors when reading
from PCC registers in the CPPC driver.
For PCC registers, base the size of read/write on the bit width field.
The debug message in cpc_read()/cpc_write() is updated to print relevant
information for the address space type used to read the register.
Fixes: 2f4a4d63a1 ("ACPI: CPPC: Use access_width over bit_width for system memory accesses")
Signed-off-by: Vanshidhar Konda <vanshikonda@os.amperecomputing.com>
Tested-by: Jarred White <jarredwhite@linux.microsoft.com>
Reviewed-by: Jarred White <jarredwhite@linux.microsoft.com>
Reviewed-by: Easwar Hariharan <eahariha@linux.microsoft.com>
Cc: 5.15+ <stable@vger.kernel.org> # 5.15+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05d92ee782 upstream.
Commit 2f4a4d63a1 ("ACPI: CPPC: Use access_width over bit_width for
system memory accesses") neglected to properly wrap the bit_offset shift
when it comes to applying the mask. This may cause incorrect values to be
read and may cause the cpufreq module not be loaded.
[ 11.059751] cpu_capacity: CPU0 missing/invalid highest performance.
[ 11.066005] cpu_capacity: partial information: fallback to 1024 for all CPUs
Also, corrected the bitmask generation in GENMASK (extra bit being added).
Fixes: 2f4a4d63a1 ("ACPI: CPPC: Use access_width over bit_width for system memory accesses")
Signed-off-by: Jarred White <jarredwhite@linux.microsoft.com>
Cc: 5.15+ <stable@vger.kernel.org> # 5.15+
Reviewed-by: Vanshidhar Konda <vanshikonda@os.amperecomputing.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f4a4d63a1 upstream.
To align with ACPI 6.3+, since bit_width can be any 8-bit value, it
cannot be depended on to be always on a clean 8b boundary. This was
uncovered on the Cobalt 100 platform.
SError Interrupt on CPU26, code 0xbe000011 -- SError
CPU: 26 PID: 1510 Comm: systemd-udevd Not tainted 5.15.2.1-13 #1
Hardware name: MICROSOFT CORPORATION, BIOS MICROSOFT CORPORATION
pstate: 62400009 (nZCv daif +PAN -UAO +TCO -DIT -SSBS BTYPE=--)
pc : cppc_get_perf_caps+0xec/0x410
lr : cppc_get_perf_caps+0xe8/0x410
sp : ffff8000155ab730
x29: ffff8000155ab730 x28: ffff0080139d0038 x27: ffff0080139d0078
x26: 0000000000000000 x25: ffff0080139d0058 x24: 00000000ffffffff
x23: ffff0080139d0298 x22: ffff0080139d0278 x21: 0000000000000000
x20: ffff00802b251910 x19: ffff0080139d0000 x18: ffffffffffffffff
x17: 0000000000000000 x16: ffffdc7e111bad04 x15: ffff00802b251008
x14: ffffffffffffffff x13: ffff013f1fd63300 x12: 0000000000000006
x11: ffffdc7e128f4420 x10: 0000000000000000 x9 : ffffdc7e111badec
x8 : ffff00802b251980 x7 : 0000000000000000 x6 : ffff0080139d0028
x5 : 0000000000000000 x4 : ffff0080139d0018 x3 : 00000000ffffffff
x2 : 0000000000000008 x1 : ffff8000155ab7a0 x0 : 0000000000000000
Kernel panic - not syncing: Asynchronous SError Interrupt
CPU: 26 PID: 1510 Comm: systemd-udevd Not tainted
5.15.2.1-13 #1
Hardware name: MICROSOFT CORPORATION, BIOS MICROSOFT CORPORATION
Call trace:
dump_backtrace+0x0/0x1e0
show_stack+0x24/0x30
dump_stack_lvl+0x8c/0xb8
dump_stack+0x18/0x34
panic+0x16c/0x384
add_taint+0x0/0xc0
arm64_serror_panic+0x7c/0x90
arm64_is_fatal_ras_serror+0x34/0xa4
do_serror+0x50/0x6c
el1h_64_error_handler+0x40/0x74
el1h_64_error+0x7c/0x80
cppc_get_perf_caps+0xec/0x410
cppc_cpufreq_cpu_init+0x74/0x400 [cppc_cpufreq]
cpufreq_online+0x2dc/0xa30
cpufreq_add_dev+0xc0/0xd4
subsys_interface_register+0x134/0x14c
cpufreq_register_driver+0x1b0/0x354
cppc_cpufreq_init+0x1a8/0x1000 [cppc_cpufreq]
do_one_initcall+0x50/0x250
do_init_module+0x60/0x27c
load_module+0x2300/0x2570
__do_sys_finit_module+0xa8/0x114
__arm64_sys_finit_module+0x2c/0x3c
invoke_syscall+0x78/0x100
el0_svc_common.constprop.0+0x180/0x1a0
do_el0_svc+0x84/0xa0
el0_svc+0x2c/0xc0
el0t_64_sync_handler+0xa4/0x12c
el0t_64_sync+0x1a4/0x1a8
Instead, use access_width to determine the size and use the offset and
width to shift and mask the bits to read/write out. Make sure to add a
check for system memory since pcc redefines the access_width to
subspace id.
If access_width is not set, then fall back to using bit_width.
Signed-off-by: Jarred White <jarredwhite@linux.microsoft.com>
Reviewed-by: Easwar Hariharan <eahariha@linux.microsoft.com>
Cc: 5.15+ <stable@vger.kernel.org> # 5.15+
[ rjw: Subject and changelog edits, comment adjustments ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c26591afd3 upstream.
The error handling path in its_vpe_irq_domain_alloc() causes a double free
when its_vpe_init() fails after successfully allocating at least one
interrupt. This happens because its_vpe_irq_domain_free() frees the
interrupts along with the area bitmap and the vprop_page and
its_vpe_irq_domain_alloc() subsequently frees the area bitmap and the
vprop_page again.
Fix this by unconditionally invoking its_vpe_irq_domain_free() which
handles all cases correctly and by removing the bitmap/vprop_page freeing
from its_vpe_irq_domain_alloc().
[ tglx: Massaged change log ]
Fixes: 7d75bbb4bc ("irqchip/gic-v3-its: Add VPE irq domain allocation/teardown")
Signed-off-by: Guanrui Huang <guanrui.huang@linux.alibaba.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240418061053.96803-2-guanrui.huang@linux.alibaba.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit efb44ff64c upstream.
As with most architectures, allow handling of read faults in VMAs that
have VM_WRITE but without VM_READ (WRITE implies READ).
Otherwise, reading before writing a write-only memory will error while
reading after writing everything is fine.
BTW, move the VM_EXEC judgement before VM_READ/VM_WRITE to make logic a
little clearer.
Cc: stable@vger.kernel.org
Fixes: 09cfefb7fa ("LoongArch: Add memory management")
Signed-off-by: Jiantao Shan <shanjiantao@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe42754b94 upstream.
Rename x86's to CPU_MITIGATIONS, define it in generic code, and force it
on for all architectures exception x86. A recent commit to turn
mitigations off by default if SPECULATION_MITIGATIONS=n kinda sorta
missed that "cpu_mitigations" is completely generic, whereas
SPECULATION_MITIGATIONS is x86-specific.
Rename x86's SPECULATIVE_MITIGATIONS instead of keeping both and have it
select CPU_MITIGATIONS, as having two configs for the same thing is
unnecessary and confusing. This will also allow x86 to use the knob to
manage mitigations that aren't strictly related to speculative
execution.
Use another Kconfig to communicate to common code that CPU_MITIGATIONS
is already defined instead of having x86's menu depend on the common
CPU_MITIGATIONS. This allows keeping a single point of contact for all
of x86's mitigations, and it's not clear that other architectures *want*
to allow disabling mitigations at compile-time.
Fixes: f337a6a21e ("x86/cpu: Actually turn off mitigations by default for SPECULATION_MITIGATIONS=n")
Closes: https://lkml.kernel.org/r/20240413115324.53303a68%40canb.auug.org.au
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Acked-by: Josh Poimboeuf <jpoimboe@kernel.org>
Acked-by: Borislav Petkov (AMD) <bp@alien8.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240420000556.2645001-2-seanjc@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f7ef5bb4a upstream.
Syzbot reported the following information leak for in
btrfs_ioctl_logical_to_ino():
BUG: KMSAN: kernel-infoleak in instrument_copy_to_user include/linux/instrumented.h:114 [inline]
BUG: KMSAN: kernel-infoleak in _copy_to_user+0xbc/0x110 lib/usercopy.c:40
instrument_copy_to_user include/linux/instrumented.h:114 [inline]
_copy_to_user+0xbc/0x110 lib/usercopy.c:40
copy_to_user include/linux/uaccess.h:191 [inline]
btrfs_ioctl_logical_to_ino+0x440/0x750 fs/btrfs/ioctl.c:3499
btrfs_ioctl+0x714/0x1260
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:904 [inline]
__se_sys_ioctl+0x261/0x450 fs/ioctl.c:890
__x64_sys_ioctl+0x96/0xe0 fs/ioctl.c:890
x64_sys_call+0x1883/0x3b50 arch/x86/include/generated/asm/syscalls_64.h:17
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xcf/0x1e0 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Uninit was created at:
__kmalloc_large_node+0x231/0x370 mm/slub.c:3921
__do_kmalloc_node mm/slub.c:3954 [inline]
__kmalloc_node+0xb07/0x1060 mm/slub.c:3973
kmalloc_node include/linux/slab.h:648 [inline]
kvmalloc_node+0xc0/0x2d0 mm/util.c:634
kvmalloc include/linux/slab.h:766 [inline]
init_data_container+0x49/0x1e0 fs/btrfs/backref.c:2779
btrfs_ioctl_logical_to_ino+0x17c/0x750 fs/btrfs/ioctl.c:3480
btrfs_ioctl+0x714/0x1260
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:904 [inline]
__se_sys_ioctl+0x261/0x450 fs/ioctl.c:890
__x64_sys_ioctl+0x96/0xe0 fs/ioctl.c:890
x64_sys_call+0x1883/0x3b50 arch/x86/include/generated/asm/syscalls_64.h:17
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xcf/0x1e0 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Bytes 40-65535 of 65536 are uninitialized
Memory access of size 65536 starts at ffff888045a40000
This happens, because we're copying a 'struct btrfs_data_container' back
to user-space. This btrfs_data_container is allocated in
'init_data_container()' via kvmalloc(), which does not zero-fill the
memory.
Fix this by using kvzalloc() which zeroes out the memory on allocation.
CC: stable@vger.kernel.org # 4.14+
Reported-by: <syzbot+510a1abbb8116eeb341d@syzkaller.appspotmail.com>
Reviewed-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Johannes Thumshirn <Johannes.thumshirn@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7192833c4e upstream.
When btrfs scrub finds an error, it reads mirrors to find correct data. If
all the errors are fixed, sctx->error_bitmap is cleared for the stripe
range. However, in the zoned mode, it runs relocation to repair scrub
errors when the bitmap is *not* empty, which is a flipped condition.
Also, it runs the relocation even if the scrub is read-only. This was
missed by a fix in commit 1f2030ff6e ("btrfs: scrub: respect the
read-only flag during repair").
The repair is only necessary when there is a repaired sector and should be
done on read-write scrub. So, tweak the condition for both regular and
zoned case.
Fixes: 54765392a1 ("btrfs: scrub: introduce helper to queue a stripe for scrub")
Fixes: 1f2030ff6e ("btrfs: scrub: respect the read-only flag during repair")
CC: stable@vger.kernel.org # 6.6+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe1c6c7acc upstream.
[BUG]
During my extent_map cleanup/refactor, with extra sanity checks,
extent-map-tests::test_case_7() would not pass the checks.
The problem is, after btrfs_drop_extent_map_range(), the resulted
extent_map has a @block_start way too large.
Meanwhile my btrfs_file_extent_item based members are returning a
correct @disk_bytenr/@offset combination.
The extent map layout looks like this:
0 16K 32K 48K
| PINNED | | Regular |
The regular em at [32K, 48K) also has 32K @block_start.
Then drop range [0, 36K), which should shrink the regular one to be
[36K, 48K).
However the @block_start is incorrect, we expect 32K + 4K, but got 52K.
[CAUSE]
Inside btrfs_drop_extent_map_range() function, if we hit an extent_map
that covers the target range but is still beyond it, we need to split
that extent map into half:
|<-- drop range -->|
|<----- existing extent_map --->|
And if the extent map is not compressed, we need to forward
extent_map::block_start by the difference between the end of drop range
and the extent map start.
However in that particular case, the difference is calculated using
(start + len - em->start).
The problem is @start can be modified if the drop range covers any
pinned extent.
This leads to wrong calculation, and would be caught by my later
extent_map sanity checks, which checks the em::block_start against
btrfs_file_extent_item::disk_bytenr + btrfs_file_extent_item::offset.
This is a regression caused by commit c962098ca4 ("btrfs: fix
incorrect splitting in btrfs_drop_extent_map_range"), which removed the
@len update for pinned extents.
[FIX]
Fix it by avoiding using @start completely, and use @end - em->start
instead, which @end is exclusive bytenr number.
And update the test case to verify the @block_start to prevent such
problem from happening.
Thankfully this is not going to lead to any data corruption, as IO path
does not utilize btrfs_drop_extent_map_range() with @skip_pinned set.
So this fix is only here for the sake of consistency/correctness.
CC: stable@vger.kernel.org # 6.5+
Fixes: c962098ca4 ("btrfs: fix incorrect splitting in btrfs_drop_extent_map_range")
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 131a821a24 upstream.
In commit b4ccace878 ("btrfs: refactor submit_compressed_extents()"), if
an async extent compressed but failed to find enough space, we changed
from falling back to an uncompressed write to just failing the write
altogether. The principle was that if there's not enough space to write
the compressed version of the data, there can't possibly be enough space
to write the larger, uncompressed version of the data.
However, this isn't necessarily true: due to fragmentation, there could
be enough discontiguous free blocks to write the uncompressed version,
but not enough contiguous free blocks to write the smaller but
unsplittable compressed version.
This has occurred to an internal workload which relied on write()'s
return value indicating there was space. While rare, it has happened a
few times.
Thus, in order to prevent early ENOSPC, re-add a fallback to
uncompressed writing.
Fixes: b4ccace878 ("btrfs: refactor submit_compressed_extents()")
CC: stable@vger.kernel.org # 6.1+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Co-developed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Sweet Tea Dorminy <sweettea-kernel@dorminy.me>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9c0f59e47a upstream.
The flag I2C_HID_READ_PENDING is used to serialize I2C operations.
However, this is not necessary, because I2C core already has its own
locking for that.
More importantly, this flag can cause a lock-up: if the flag is set in
i2c_hid_xfer() and an interrupt happens, the interrupt handler
(i2c_hid_irq) will check this flag and return immediately without doing
anything, then the interrupt handler will be invoked again in an
infinite loop.
Since interrupt handler is an RT task, it takes over the CPU and the
flag-clearing task never gets scheduled, thus we have a lock-up.
Delete this unnecessary flag.
Reported-and-tested-by: Eva Kurchatova <nyandarknessgirl@gmail.com>
Closes: https://lore.kernel.org/r/CA+eeCSPUDpUg76ZO8dszSbAGn+UHjcyv8F1J-CUPVARAzEtW9w@mail.gmail.com
Fixes: 4a200c3b9a ("HID: i2c-hid: introduce HID over i2c specification implementation")
Cc: <stable@vger.kernel.org>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b61bb5bc2c upstream.
While migrating to exec_ops in commit a82990c8a4 ("mtd: rawnand: qcom:
Add read/read_start ops in exec_op path"), OP_RESET_DEVICE command handling
got broken unintentionally. Right now for the OP_RESET_DEVICE command,
qcom_misc_cmd_type_exec() will simply return 0 without handling it. Even,
if that gets fixed, an unnecessary FLASH_STATUS read descriptor command is
being added in the middle and that seems to be causing the command to fail
on IPQ806x devices.
So let's fix the above two issues to make OP_RESET_DEVICE command working
again.
Fixes: a82990c8a4 ("mtd: rawnand: qcom: Add read/read_start ops in exec_op path")
Cc: stable@vger.kernel.org
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240404083157.940-1-ansuelsmth@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ddb9de6af upstream.
Qualcomm ROME controllers can be registered from the Bluetooth line
discipline and in this case the HCI UART serdev pointer is NULL.
Add the missing sanity check to prevent a NULL-pointer dereference when
setup() is called for a non-serdev controller.
Fixes: e9b3e5b8c6 ("Bluetooth: hci_qca: only assign wakeup with serial port support")
Cc: stable@vger.kernel.org # 6.2
Cc: Zhengping Jiang <jiangzp@google.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 73e87c0a49 upstream.
Qualcomm ROME controllers can be registered from the Bluetooth line
discipline and in this case the HCI UART serdev pointer is NULL.
Add the missing sanity check to prevent a NULL-pointer dereference when
wakeup() is called for a non-serdev controller during suspend.
Just return true for now to restore the original behaviour and address
the crash with pre-6.2 kernels, which do not have commit e9b3e5b8c6
("Bluetooth: hci_qca: only assign wakeup with serial port support") that
causes the crash to happen already at setup() time.
Fixes: c1a74160ea ("Bluetooth: hci_qca: Add device_may_wakeup support")
Cc: stable@vger.kernel.org # 5.13
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9bf4e919cc upstream.
After an innocuous optimization change in LLVM main (19.0.0), x86_64
allmodconfig (which enables CONFIG_KCSAN / -fsanitize=thread) fails to
build due to the checks in check_copy_size():
In file included from net/bluetooth/sco.c:27:
In file included from include/linux/module.h:13:
In file included from include/linux/stat.h:19:
In file included from include/linux/time.h:60:
In file included from include/linux/time32.h:13:
In file included from include/linux/timex.h:67:
In file included from arch/x86/include/asm/timex.h:6:
In file included from arch/x86/include/asm/tsc.h:10:
In file included from arch/x86/include/asm/msr.h:15:
In file included from include/linux/percpu.h:7:
In file included from include/linux/smp.h:118:
include/linux/thread_info.h:244:4: error: call to '__bad_copy_from'
declared with 'error' attribute: copy source size is too small
244 | __bad_copy_from();
| ^
The same exact error occurs in l2cap_sock.c. The copy_to_user()
statements that are failing come from l2cap_sock_getsockopt_old() and
sco_sock_getsockopt_old(). This does not occur with GCC with or without
KCSAN or Clang without KCSAN enabled.
len is defined as an 'int' because it is assigned from
'__user int *optlen'. However, it is clamped against the result of
sizeof(), which has a type of 'size_t' ('unsigned long' for 64-bit
platforms). This is done with min_t() because min() requires compatible
types, which results in both len and the result of sizeof() being casted
to 'unsigned int', meaning len changes signs and the result of sizeof()
is truncated. From there, len is passed to copy_to_user(), which has a
third parameter type of 'unsigned long', so it is widened and changes
signs again. This excessive casting in combination with the KCSAN
instrumentation causes LLVM to fail to eliminate the __bad_copy_from()
call, failing the build.
The official recommendation from LLVM developers is to consistently use
long types for all size variables to avoid the unnecessary casting in
the first place. Change the type of len to size_t in both
l2cap_sock_getsockopt_old() and sco_sock_getsockopt_old(). This clears
up the error while allowing min_t() to be replaced with min(), resulting
in simpler code with no casts and fewer implicit conversions. While len
is a different type than optlen now, it should result in no functional
change because the result of sizeof() will clamp all values of optlen in
the same manner as before.
Cc: stable@vger.kernel.org
Closes: https://github.com/ClangBuiltLinux/linux/issues/2007
Link: https://github.com/llvm/llvm-project/issues/85647
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Justin Stitt <justinstitt@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ded103c7eb upstream.
If one attempts to build an essentially empty file somewhere in the
kernel tree, it leads to a build error because the compiler does not
recognize the `new_uninit` unstable feature:
error[E0635]: unknown feature `new_uninit`
--> <crate attribute>:1:9
|
1 | feature(new_uninit)
| ^^^^^^^^^^
The reason is that we pass `-Zcrate-attr='feature(new_uninit)'` (together
with `-Zallow-features=new_uninit`) to let non-`rust/` code use that
unstable feature.
However, the compiler only recognizes the feature if the `alloc` crate
is resolved (the feature is an `alloc` one). `--extern alloc`, which we
pass, is not enough to resolve the crate.
Introducing a reference like `use alloc;` or `extern crate alloc;`
solves the issue, thus this is not seen in normal files. For instance,
`use`ing the `kernel` prelude introduces such a reference, since `alloc`
is used inside.
While normal use of the build system is not impacted by this, it can still
be fairly confusing for kernel developers [1], thus use the unstable
`force` option of `--extern` [2] (added in Rust 1.71 [3]) to force the
compiler to resolve `alloc`.
This new unstable feature is only needed meanwhile we use the other
unstable feature, since then we will not need `-Zcrate-attr`.
Cc: stable@vger.kernel.org # v6.6+
Reported-by: Daniel Almeida <daniel.almeida@collabora.com>
Reported-by: Julian Stecklina <julian.stecklina@cyberus-technology.de>
Closes: https://rust-for-linux.zulipchat.com/#narrow/stream/288089-General/topic/x/near/424096982 [1]
Fixes: 2f7ab1267d ("Kbuild: add Rust support")
Link: https://github.com/rust-lang/rust/issues/111302 [2]
Link: https://github.com/rust-lang/rust/pull/109421 [3]
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Reviewed-by: Gary Guo <gary@garyguo.net>
Link: https://lore.kernel.org/r/20240422090644.525520-1-ojeda@kernel.org
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 49ceae68a0 upstream.
In Rust, producing an invalid value of any type is immediate undefined
behavior (UB); this includes via zeroing memory. Therefore, since an
uninhabited type has no valid values, producing any values at all for it is
UB.
The Rust standard library type `core::convert::Infallible` is uninhabited,
by virtue of having been declared as an enum with no cases, which always
produces uninhabited types in Rust.
The current kernel code allows this UB to be triggered, for example by code
like `Box::<core::convert::Infallible>::init(kernel::init::zeroed())`.
Thus, remove the implementation of `Zeroable` for `Infallible`, thereby
avoiding the unsoundness (potential for future UB).
Cc: stable@vger.kernel.org
Fixes: 38cde0bd7b ("rust: init: add `Zeroable` trait and `init::zeroed` function")
Closes: https://github.com/Rust-for-Linux/pinned-init/pull/13
Signed-off-by: Laine Taffin Altman <alexanderaltman@me.com>
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Reviewed-by: Boqun Feng <boqun.feng@gmail.com>
Reviewed-by: Benno Lossin <benno.lossin@proton.me>
Link: https://lore.kernel.org/r/CA160A4E-561E-4918-837E-3DCEBA74F808@me.com
[ Reformatted the comment slightly. ]
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d49f53af4 upstream.
This was originally part of commit 4b9a68f2e59a0 ("rust: add support for
static synchronisation primitives") from the old Rust branch, which used
module constructors to initialize globals containing various
synchronisation primitives with pin-init. That commit has never been
upstreamed, but the `select CONSTRUCTORS` statement ended up being
included in the patch that initially added Rust support to the Linux
Kernel.
We are not using module constructors, so let's remove the select.
Signed-off-by: Alice Ryhl <aliceryhl@google.com>
Reviewed-by: Benno Lossin <benno.lossin@proton.me>
Cc: stable@vger.kernel.org
Fixes: 2f7ab1267d ("Kbuild: add Rust support")
Link: https://lore.kernel.org/r/20240308-constructors-v1-1-4c811342391c@google.com
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b53c6bd5d2 upstream.
cpu_feature_enabled(X86_FEATURE_OSPKE) does not necessarily reflect
whether CR4.PKE is set on the CPU. In particular, they may differ on
non-BSP CPUs before setup_pku() is executed. In this scenario, RDPKRU
will #UD causing the system to hang.
Fix by checking CR4 for PKE enablement which is always correct for the
current CPU.
The scenario happens by inserting a WARN* before setup_pku() in
identiy_cpu() or some other diagnostic which would lead to calling
__show_regs().
[ bp: Massage commit message. ]
Signed-off-by: David Kaplan <david.kaplan@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20240421191728.32239-1-bp@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e3c9f9f3a upstream.
Currently the user_notification_addfd test checks what the next expected
file descriptor will be by incrementing a variable nextfd. This does not
account for file descriptors that may already be open before the test is
started and will cause the test to fail if any exist.
Replace nextfd++ with a function get_next_fd which will check and return
the next available file descriptor.
Signed-off-by: Terry Tritton <terry.tritton@linaro.org>
Link: https://lore.kernel.org/r/20240124141357.1243457-4-terry.tritton@linaro.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9253c54e01 ]
Syskiller has produced an out of bounds access in fill_meta_index().
That out of bounds access is ultimately caused because the inode
has an inode number with the invalid value of zero, which was not checked.
The reason this causes the out of bounds access is due to following
sequence of events:
1. Fill_meta_index() is called to allocate (via empty_meta_index())
and fill a metadata index. It however suffers a data read error
and aborts, invalidating the newly returned empty metadata index.
It does this by setting the inode number of the index to zero,
which means unused (zero is not a valid inode number).
2. When fill_meta_index() is subsequently called again on another
read operation, locate_meta_index() returns the previous index
because it matches the inode number of 0. Because this index
has been returned it is expected to have been filled, and because
it hasn't been, an out of bounds access is performed.
This patch adds a sanity check which checks that the inode number
is not zero when the inode is created and returns -EINVAL if it is.
[phillip@squashfs.org.uk: whitespace fix]
Link: https://lkml.kernel.org/r/20240409204723.446925-1-phillip@squashfs.org.uk
Link: https://lkml.kernel.org/r/20240408220206.435788-1-phillip@squashfs.org.uk
Signed-off-by: Phillip Lougher <phillip@squashfs.org.uk>
Reported-by: "Ubisectech Sirius" <bugreport@ubisectech.com>
Closes: https://lore.kernel.org/lkml/87f5c007-b8a5-41ae-8b57-431e924c5915.bugreport@ubisectech.com/
Cc: Christian Brauner <brauner@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6976f323a ]
We only pool write combined and uncached allocations because they
require extra overhead on allocation and release.
If we also pool cached NUMA it not only means some extra unnecessary
overhead, but also that under memory pressure it can happen that
pages from the wrong NUMA node enters the pool and are re-used
over and over again.
This can lead to performance reduction after running into memory
pressure.
v2: restructure and cleanup the code a bit from the internal hack to
test this.
Signed-off-by: Christian König <christian.koenig@amd.com>
Fixes: 4482d3c94d ("drm/ttm: add NUMA node id to the pool")
CC: stable@vger.kernel.org
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240415134821.1919-1-christian.koenig@amd.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6ff969fe9 ]
When we removed the hacky start code check we actually didn't took into
account that *all* VRAM pages needs to be CPU accessible.
Clean up the code and unify the handling into a single helper which
checks if the whole resource is CPU accessible.
The only place where a partial check would make sense is during
eviction, but that is neglitible.
Signed-off-by: Christian König <christian.koenig@amd.com>
Fixes: aed01a6804 ("drm/amdgpu: Remove TTM resource->start visible VRAM condition v2")
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
CC: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 631426ba1d ]
Darrick reports that in some cases where pread() would fail with -EIO and
mmap()+access would generate a SIGBUS signal, MADV_POPULATE_READ /
MADV_POPULATE_WRITE will keep retrying forever and not fail with -EFAULT.
While the madvise() call can be interrupted by a signal, this is not the
desired behavior. MADV_POPULATE_READ / MADV_POPULATE_WRITE should behave
like page faults in that case: fail and not retry forever.
A reproducer can be found at [1].
The reason is that __get_user_pages(), as called by
faultin_vma_page_range(), will not handle VM_FAULT_RETRY in a proper way:
it will simply return 0 when VM_FAULT_RETRY happened, making
madvise_populate()->faultin_vma_page_range() retry again and again, never
setting FOLL_TRIED->FAULT_FLAG_TRIED for __get_user_pages().
__get_user_pages_locked() does what we want, but duplicating that logic in
faultin_vma_page_range() feels wrong.
So let's use __get_user_pages_locked() instead, that will detect
VM_FAULT_RETRY and set FOLL_TRIED when retrying, making the fault handler
return VM_FAULT_SIGBUS (VM_FAULT_ERROR) at some point, propagating -EFAULT
from faultin_page() to __get_user_pages(), all the way to
madvise_populate().
But, there is an issue: __get_user_pages_locked() will end up re-taking
the MM lock and then __get_user_pages() will do another VMA lookup. In
the meantime, the VMA layout could have changed and we'd fail with
different error codes than we'd want to.
As __get_user_pages() will currently do a new VMA lookup either way, let
it do the VMA handling in a different way, controlled by a new
FOLL_MADV_POPULATE flag, effectively moving these checks from
madvise_populate() + faultin_page_range() in there.
With this change, Darricks reproducer properly fails with -EFAULT, as
documented for MADV_POPULATE_READ / MADV_POPULATE_WRITE.
[1] https://lore.kernel.org/all/20240313171936.GN1927156@frogsfrogsfrogs/
Link: https://lkml.kernel.org/r/20240314161300.382526-1-david@redhat.com
Link: https://lkml.kernel.org/r/20240314161300.382526-2-david@redhat.com
Fixes: 4ca9b3859d ("mm/madvise: introduce MADV_POPULATE_(READ|WRITE) to prefault page tables")
Signed-off-by: David Hildenbrand <david@redhat.com>
Reported-by: Darrick J. Wong <djwong@kernel.org>
Closes: https://lore.kernel.org/all/20240311223815.GW1927156@frogsfrogsfrogs/
Cc: Darrick J. Wong <djwong@kernel.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Jason Gunthorpe <jgg@nvidia.com>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de120e1d69 ]
Set the enable bits for general purpose counters in IA32_PERF_GLOBAL_CTRL
when refreshing the PMU to emulate the MSR's architecturally defined
post-RESET behavior. Per Intel's SDM:
IA32_PERF_GLOBAL_CTRL: Sets bits n-1:0 and clears the upper bits.
and
Where "n" is the number of general-purpose counters available in the processor.
AMD also documents this behavior for PerfMonV2 CPUs in one of AMD's many
PPRs.
Do not set any PERF_GLOBAL_CTRL bits if there are no general purpose
counters, although a literal reading of the SDM would require the CPU to
set either bits 63:0 or 31:0. The intent of the behavior is to globally
enable all GP counters; honor the intent, if not the letter of the law.
Leaving PERF_GLOBAL_CTRL '0' effectively breaks PMU usage in guests that
haven't been updated to work with PMUs that support PERF_GLOBAL_CTRL.
This bug was recently exposed when KVM added supported for AMD's
PerfMonV2, i.e. when KVM started exposing a vPMU with PERF_GLOBAL_CTRL to
guest software that only knew how to program v1 PMUs (that don't support
PERF_GLOBAL_CTRL).
Failure to emulate the post-RESET behavior results in such guests
unknowingly leaving all general purpose counters globally disabled (the
entire reason the post-RESET value sets the GP counter enable bits is to
maintain backwards compatibility).
The bug has likely gone unnoticed because PERF_GLOBAL_CTRL has been
supported on Intel CPUs for as long as KVM has existed, i.e. hardly anyone
is running guest software that isn't aware of PERF_GLOBAL_CTRL on Intel
PMUs. And because up until v6.0, KVM _did_ emulate the behavior for Intel
CPUs, although the old behavior was likely dumb luck.
Because (a) that old code was also broken in its own way (the history of
this code is a comedy of errors), and (b) PERF_GLOBAL_CTRL was documented
as having a value of '0' post-RESET in all SDMs before March 2023.
Initial vPMU support in commit f5132b0138 ("KVM: Expose a version 2
architectural PMU to a guests") *almost* got it right (again likely by
dumb luck), but for some reason only set the bits if the guest PMU was
advertised as v1:
if (pmu->version == 1) {
pmu->global_ctrl = (1 << pmu->nr_arch_gp_counters) - 1;
return;
}
Commit f19a0c2c2e ("KVM: PMU emulation: GLOBAL_CTRL MSR should be
enabled on reset") then tried to remedy that goof, presumably because
guest PMUs were leaving PERF_GLOBAL_CTRL '0', i.e. weren't enabling
counters.
pmu->global_ctrl = ((1 << pmu->nr_arch_gp_counters) - 1) |
(((1ull << pmu->nr_arch_fixed_counters) - 1) << X86_PMC_IDX_FIXED);
pmu->global_ctrl_mask = ~pmu->global_ctrl;
That was KVM's behavior up until commit c49467a45f ("KVM: x86/pmu:
Don't overwrite the pmu->global_ctrl when refreshing") removed
*everything*. However, it did so based on the behavior defined by the
SDM , which at the time stated that "Global Perf Counter Controls" is
'0' at Power-Up and RESET.
But then the March 2023 SDM (325462-079US), stealthily changed its
"IA-32 and Intel 64 Processor States Following Power-up, Reset, or INIT"
table to say:
IA32_PERF_GLOBAL_CTRL: Sets bits n-1:0 and clears the upper bits.
Note, kvm_pmu_refresh() can be invoked multiple times, i.e. it's not a
"pure" RESET flow. But it can only be called prior to the first KVM_RUN,
i.e. the guest will only ever observe the final value.
Note #2, KVM has always cleared global_ctrl during refresh (see commit
f5132b0138 ("KVM: Expose a version 2 architectural PMU to a guests")),
i.e. there is no danger of breaking existing setups by clobbering a value
set by userspace.
Reported-by: Babu Moger <babu.moger@amd.com>
Cc: Sandipan Das <sandipan.das@amd.com>
Cc: Like Xu <like.xu.linux@gmail.com>
Cc: Mingwei Zhang <mizhang@google.com>
Cc: Dapeng Mi <dapeng1.mi@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Dapeng Mi <dapeng1.mi@linux.intel.com>
Tested-by: Dapeng Mi <dapeng1.mi@linux.intel.com>
Link: https://lore.kernel.org/r/20240309013641.1413400-2-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f933b88e20 ]
Move the purging of common PMU metadata from intel_pmu_refresh() to
kvm_pmu_refresh(), and invoke the vendor refresh() hook if and only if
the VM is supposed to have a vPMU.
KVM already denies access to the PMU based on kvm->arch.enable_pmu, as
get_gp_pmc_amd() returns NULL for all PMCs in that case, i.e. KVM already
violates AMD's architecture by not virtualizing a PMU (kernels have long
since learned to not panic when the PMU is unavailable). But configuring
the PMU as if it were enabled causes unwanted side effects, e.g. calls to
kvm_pmu_trigger_event() waste an absurd number of cycles due to the
all_valid_pmc_idx bitmap being non-zero.
Fixes: b1d66dad65 ("KVM: x86/svm: Add module param to control PMU virtualization")
Reported-by: Konstantin Khorenko <khorenko@virtuozzo.com>
Closes: https://lore.kernel.org/all/20231109180646.2963718-2-khorenko@virtuozzo.com
Link: https://lore.kernel.org/r/20231110022857.1273836-2-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Stable-dep-of: de120e1d69 ("KVM: x86/pmu: Set enable bits for GP counters in PERF_GLOBAL_CTRL at "RESET"")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b9e743e92 ]
The CPTS, by design, captures the messageType (Sync, Delay_Req, etc.)
field from the second nibble of the PTP header which is defined in the
PTPv2 (1588-2008) specification. In the PTPv1 (1588-2002) specification
the first two bytes of the PTP header are defined as the versionType
which is always 0x0001. This means that any PTPv1 packets that are
tagged for TX timestamping by the CPTS will have their messageType set
to 0x0 which corresponds to a Sync message type. This causes issues
when a PTPv1 stack is expecting a Delay_Req (messageType: 0x1)
timestamp that never appears.
Fix this by checking if the ptp_class of the timestamped TX packet is
PTP_CLASS_V1 and then matching the PTP sequence ID to the stored
sequence ID in the skb->cb data structure. If the sequence IDs match
and the packet is of type PTPv1 then there is a chance that the
messageType has been incorrectly stored by the CPTS so overwrite the
messageType stored by the CPTS with the messageType from the skb->cb
data structure. This allows the PTPv1 stack to receive TX timestamps
for Delay_Req packets which are necessary to lock onto a PTP Leader.
Signed-off-by: Jason Reeder <jreeder@ti.com>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Tested-by: Ed Trexel <ed.trexel@hp.com>
Fixes: f6bd59526c ("net: ethernet: ti: introduce am654 common platform time sync driver")
Link: https://lore.kernel.org/r/20240424071626.32558-1-r-gunasekaran@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 96fdd1f6b4 ]
9f74a3dfcf ("ice: Fix VF Reset paths when interface in a failed over
aggregate"), the ice driver has acquired the LAG mutex in ice_reset_vf().
The commit placed this lock acquisition just prior to the acquisition of
the VF configuration lock.
If ice_reset_vf() acquires the configuration lock via the ICE_VF_RESET_LOCK
flag, this could deadlock with ice_vc_cfg_qs_msg() because it always
acquires the locks in the order of the VF configuration lock and then the
LAG mutex.
Lockdep reports this violation almost immediately on creating and then
removing 2 VF:
======================================================
WARNING: possible circular locking dependency detected
6.8.0-rc6 #54 Tainted: G W O
------------------------------------------------------
kworker/60:3/6771 is trying to acquire lock:
ff40d43e099380a0 (&vf->cfg_lock){+.+.}-{3:3}, at: ice_reset_vf+0x22f/0x4d0 [ice]
but task is already holding lock:
ff40d43ea1961210 (&pf->lag_mutex){+.+.}-{3:3}, at: ice_reset_vf+0xb7/0x4d0 [ice]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&pf->lag_mutex){+.+.}-{3:3}:
__lock_acquire+0x4f8/0xb40
lock_acquire+0xd4/0x2d0
__mutex_lock+0x9b/0xbf0
ice_vc_cfg_qs_msg+0x45/0x690 [ice]
ice_vc_process_vf_msg+0x4f5/0x870 [ice]
__ice_clean_ctrlq+0x2b5/0x600 [ice]
ice_service_task+0x2c9/0x480 [ice]
process_one_work+0x1e9/0x4d0
worker_thread+0x1e1/0x3d0
kthread+0x104/0x140
ret_from_fork+0x31/0x50
ret_from_fork_asm+0x1b/0x30
-> #0 (&vf->cfg_lock){+.+.}-{3:3}:
check_prev_add+0xe2/0xc50
validate_chain+0x558/0x800
__lock_acquire+0x4f8/0xb40
lock_acquire+0xd4/0x2d0
__mutex_lock+0x9b/0xbf0
ice_reset_vf+0x22f/0x4d0 [ice]
ice_process_vflr_event+0x98/0xd0 [ice]
ice_service_task+0x1cc/0x480 [ice]
process_one_work+0x1e9/0x4d0
worker_thread+0x1e1/0x3d0
kthread+0x104/0x140
ret_from_fork+0x31/0x50
ret_from_fork_asm+0x1b/0x30
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&pf->lag_mutex);
lock(&vf->cfg_lock);
lock(&pf->lag_mutex);
lock(&vf->cfg_lock);
*** DEADLOCK ***
4 locks held by kworker/60:3/6771:
#0: ff40d43e05428b38 ((wq_completion)ice){+.+.}-{0:0}, at: process_one_work+0x176/0x4d0
#1: ff50d06e05197e58 ((work_completion)(&pf->serv_task)){+.+.}-{0:0}, at: process_one_work+0x176/0x4d0
#2: ff40d43ea1960e50 (&pf->vfs.table_lock){+.+.}-{3:3}, at: ice_process_vflr_event+0x48/0xd0 [ice]
#3: ff40d43ea1961210 (&pf->lag_mutex){+.+.}-{3:3}, at: ice_reset_vf+0xb7/0x4d0 [ice]
stack backtrace:
CPU: 60 PID: 6771 Comm: kworker/60:3 Tainted: G W O 6.8.0-rc6 #54
Hardware name:
Workqueue: ice ice_service_task [ice]
Call Trace:
<TASK>
dump_stack_lvl+0x4a/0x80
check_noncircular+0x12d/0x150
check_prev_add+0xe2/0xc50
? save_trace+0x59/0x230
? add_chain_cache+0x109/0x450
validate_chain+0x558/0x800
__lock_acquire+0x4f8/0xb40
? lockdep_hardirqs_on+0x7d/0x100
lock_acquire+0xd4/0x2d0
? ice_reset_vf+0x22f/0x4d0 [ice]
? lock_is_held_type+0xc7/0x120
__mutex_lock+0x9b/0xbf0
? ice_reset_vf+0x22f/0x4d0 [ice]
? ice_reset_vf+0x22f/0x4d0 [ice]
? rcu_is_watching+0x11/0x50
? ice_reset_vf+0x22f/0x4d0 [ice]
ice_reset_vf+0x22f/0x4d0 [ice]
? process_one_work+0x176/0x4d0
ice_process_vflr_event+0x98/0xd0 [ice]
ice_service_task+0x1cc/0x480 [ice]
process_one_work+0x1e9/0x4d0
worker_thread+0x1e1/0x3d0
? __pfx_worker_thread+0x10/0x10
kthread+0x104/0x140
? __pfx_kthread+0x10/0x10
ret_from_fork+0x31/0x50
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1b/0x30
</TASK>
To avoid deadlock, we must acquire the LAG mutex only after acquiring the
VF configuration lock. Fix the ice_reset_vf() to acquire the LAG mutex only
after we either acquire or check that the VF configuration lock is held.
Fixes: 9f74a3dfcf ("ice: Fix VF Reset paths when interface in a failed over aggregate")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Dave Ertman <david.m.ertman@intel.com>
Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Tested-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240423182723.740401-5-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef3c313119 ]
If the MFS is set below the default (0x2600), a warning message is
reported like the following :
MFS for port 1 has been set below the default: 600
This message is a bit confusing as the number shown here (600) is in
fact an hexa number: 0x600 = 1536
Without any explicit "0x" prefix, this message is read like the MFS is
set to 600 bytes.
MFS, as per MTUs, are usually expressed in decimal base.
This commit reports both current and default MFS values in decimal
so it's less confusing for end-users.
A typical warning message looks like the following :
MFS for port 1 (1536) has been set below the default (9728)
Signed-off-by: Erwan Velu <e.velu@criteo.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fixes: 3a2c6ced90 ("i40e: Add a check to see if MFS is set")
Link: https://lore.kernel.org/r/20240423182723.740401-3-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c9cd59dbc ]
The DP83869 driver sets the MII bit (needed for PHY to work in MII mode)
only if the op-mode is either DP83869_100M_MEDIA_CONVERT or
DP83869_RGMII_100_BASE.
Some drivers i.e. ICSSG support MII mode with op-mode as
DP83869_RGMII_COPPER_ETHERNET for which the MII bit is not set in dp83869
driver. As a result MII mode on ICSSG doesn't work and below log is seen.
TI DP83869 300b2400.mdio:0f: selected op-mode is not valid with MII mode
icssg-prueth icssg1-eth: couldn't connect to phy ethernet-phy@0
icssg-prueth icssg1-eth: can't phy connect port MII0
Fix this by setting MII bit for DP83869_RGMII_COPPER_ETHERNET op-mode as
well.
Fixes: 94e86ef1b8 ("net: phy: dp83869: support mii mode when rgmii strap cfg is used")
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7301177307 ]
I added OOM and netpoll discard counters, naively assuming that
the cpr pointer is pointing to a common completion ring.
Turns out that is usually *a* completion ring but not *the*
completion ring which bnapi->cp_ring points to. bnapi->cp_ring
is where the stats are read from, so we end up reporting 0
thru ethtool -S and qstat even though the drop events have happened.
Make 100% sure we're recording statistics in the correct structure.
Fixes: 907fd4a294 ("bnxt: count discards due to memory allocation errors")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20240424002148.3937059-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb4e2b70a7 ]
The rehash delayed work is rescheduled with a delay if the number of
credits at end of the work is not negative as supposedly it means that
the migration ended. Otherwise, it is rescheduled immediately.
After "mlxsw: spectrum_acl_tcam: Fix possible use-after-free during
rehash" the above is no longer accurate as a non-negative number of
credits is no longer indicative of the migration being done. It can also
happen if the work encountered an error in which case the migration will
resume the next time the work is scheduled.
The significance of the above is that it is possible for the work to be
pending and associated with hints that were allocated when the migration
started. This leads to the hints being leaked [1] when the work is
canceled while pending as part of ACL region dismantle.
Fix by freeing the hints if hints are associated with a work that was
canceled while pending.
Blame the original commit since the reliance on not having a pending
work associated with hints is fragile.
[1]
unreferenced object 0xffff88810e7c3000 (size 256):
comm "kworker/0:16", pid 176, jiffies 4295460353
hex dump (first 32 bytes):
00 30 95 11 81 88 ff ff 61 00 00 00 00 00 00 80 .0......a.......
00 00 61 00 40 00 00 00 00 00 00 00 04 00 00 00 ..a.@...........
backtrace (crc 2544ddb9):
[<00000000cf8cfab3>] kmalloc_trace+0x23f/0x2a0
[<000000004d9a1ad9>] objagg_hints_get+0x42/0x390
[<000000000b143cf3>] mlxsw_sp_acl_erp_rehash_hints_get+0xca/0x400
[<0000000059bdb60a>] mlxsw_sp_acl_tcam_vregion_rehash_work+0x868/0x1160
[<00000000e81fd734>] process_one_work+0x59c/0xf20
[<00000000ceee9e81>] worker_thread+0x799/0x12c0
[<00000000bda6fe39>] kthread+0x246/0x300
[<0000000070056d23>] ret_from_fork+0x34/0x70
[<00000000dea2b93e>] ret_from_fork_asm+0x1a/0x30
Fixes: c9c9af91f1 ("mlxsw: spectrum_acl: Allow to interrupt/continue rehash work")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Alexander Zubkov <green@qrator.net>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/0cc12ebb07c4d4c41a1265ee2c28b392ff997a86.1713797103.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b377add0f0 ]
Both the function that migrates all the chunks within a region and the
function that migrates all the entries within a chunk call
list_first_entry() on the respective lists without checking that the
lists are not empty. This is incorrect usage of the API, which leads to
the following warning [1].
Fix by returning if the lists are empty as there is nothing to migrate
in this case.
[1]
WARNING: CPU: 0 PID: 6437 at drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c:1266 mlxsw_sp_acl_tcam_vchunk_migrate_all+0x1f1/0>
Modules linked in:
CPU: 0 PID: 6437 Comm: kworker/0:37 Not tainted 6.9.0-rc3-custom-00883-g94a65f079ef6 #39
Hardware name: Mellanox Technologies Ltd. MSN3700/VMOD0005, BIOS 5.11 01/06/2019
Workqueue: mlxsw_core mlxsw_sp_acl_tcam_vregion_rehash_work
RIP: 0010:mlxsw_sp_acl_tcam_vchunk_migrate_all+0x1f1/0x2c0
[...]
Call Trace:
<TASK>
mlxsw_sp_acl_tcam_vregion_rehash_work+0x6c/0x4a0
process_one_work+0x151/0x370
worker_thread+0x2cb/0x3e0
kthread+0xd0/0x100
ret_from_fork+0x34/0x50
ret_from_fork_asm+0x1a/0x30
</TASK>
Fixes: 6f9579d4e3 ("mlxsw: spectrum_acl: Remember where to continue rehash migration")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Alexander Zubkov <green@qrator.net>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/4628e9a22d1d84818e28310abbbc498e7bc31bc9.1713797103.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 743edc8547 ]
As previously explained, the rehash delayed work migrates filters from
one region to another. This is done by iterating over all chunks (all
the filters with the same priority) in the region and in each chunk
iterating over all the filters.
When the work runs out of credits it stores the current chunk and entry
as markers in the per-work context so that it would know where to resume
the migration from the next time the work is scheduled.
Upon error, the chunk marker is reset to NULL, but without resetting the
entry markers despite being relative to it. This can result in migration
being resumed from an entry that does not belong to the chunk being
migrated. In turn, this will eventually lead to a chunk being iterated
over as if it is an entry. Because of how the two structures happen to
be defined, this does not lead to KASAN splats, but to warnings such as
[1].
Fix by creating a helper that resets all the markers and call it from
all the places the currently only reset the chunk marker. For good
measures also call it when starting a completely new rehash. Add a
warning to avoid future cases.
[1]
WARNING: CPU: 7 PID: 1076 at drivers/net/ethernet/mellanox/mlxsw/core_acl_flex_keys.c:407 mlxsw_afk_encode+0x242/0x2f0
Modules linked in:
CPU: 7 PID: 1076 Comm: kworker/7:24 Tainted: G W 6.9.0-rc3-custom-00880-g29e61d91b77b #29
Hardware name: Mellanox Technologies Ltd. MSN3700/VMOD0005, BIOS 5.11 01/06/2019
Workqueue: mlxsw_core mlxsw_sp_acl_tcam_vregion_rehash_work
RIP: 0010:mlxsw_afk_encode+0x242/0x2f0
[...]
Call Trace:
<TASK>
mlxsw_sp_acl_atcam_entry_add+0xd9/0x3c0
mlxsw_sp_acl_tcam_entry_create+0x5e/0xa0
mlxsw_sp_acl_tcam_vchunk_migrate_all+0x109/0x290
mlxsw_sp_acl_tcam_vregion_rehash_work+0x6c/0x470
process_one_work+0x151/0x370
worker_thread+0x2cb/0x3e0
kthread+0xd0/0x100
ret_from_fork+0x34/0x50
</TASK>
Fixes: 6f9579d4e3 ("mlxsw: spectrum_acl: Remember where to continue rehash migration")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Alexander Zubkov <green@qrator.net>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/cc17eed86b41dd829d39b07906fec074a9ce580e.1713797103.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ca3f7a7b6 ]
The rehash delayed work migrates filters from one region to another.
This is done by iterating over all chunks (all the filters with the same
priority) in the region and in each chunk iterating over all the
filters.
If the migration fails, the code tries to migrate the filters back to
the old region. However, the rollback itself can also fail in which case
another migration will be erroneously performed. Besides the fact that
this ping pong is not a very good idea, it also creates a problem.
Each virtual chunk references two chunks: The currently used one
('vchunk->chunk') and a backup ('vchunk->chunk2'). During migration the
first holds the chunk we want to migrate filters to and the second holds
the chunk we are migrating filters from.
The code currently assumes - but does not verify - that the backup chunk
does not exist (NULL) if the currently used chunk does not reference the
target region. This assumption breaks when we are trying to rollback a
rollback, resulting in the backup chunk being overwritten and leaked
[1].
Fix by not rolling back a failed rollback and add a warning to avoid
future cases.
[1]
WARNING: CPU: 5 PID: 1063 at lib/parman.c:291 parman_destroy+0x17/0x20
Modules linked in:
CPU: 5 PID: 1063 Comm: kworker/5:11 Tainted: G W 6.9.0-rc2-custom-00784-gc6a05c468a0b #14
Hardware name: Mellanox Technologies Ltd. MSN3700/VMOD0005, BIOS 5.11 01/06/2019
Workqueue: mlxsw_core mlxsw_sp_acl_tcam_vregion_rehash_work
RIP: 0010:parman_destroy+0x17/0x20
[...]
Call Trace:
<TASK>
mlxsw_sp_acl_atcam_region_fini+0x19/0x60
mlxsw_sp_acl_tcam_region_destroy+0x49/0xf0
mlxsw_sp_acl_tcam_vregion_rehash_work+0x1f1/0x470
process_one_work+0x151/0x370
worker_thread+0x2cb/0x3e0
kthread+0xd0/0x100
ret_from_fork+0x34/0x50
ret_from_fork_asm+0x1a/0x30
</TASK>
Fixes: 8435005185 ("mlxsw: spectrum_acl: Do rollback as another call to mlxsw_sp_acl_tcam_vchunk_migrate_all()")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Alexander Zubkov <green@qrator.net>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/d5edd4f4503934186ae5cfe268503b16345b4e0f.1713797103.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5422598888 ]
The rehash delayed work migrates filters from one region to another
according to the number of available credits.
The migrated from region is destroyed at the end of the work if the
number of credits is non-negative as the assumption is that this is
indicative of migration being complete. This assumption is incorrect as
a non-negative number of credits can also be the result of a failed
migration.
The destruction of a region that still has filters referencing it can
result in a use-after-free [1].
Fix by not destroying the region if migration failed.
[1]
BUG: KASAN: slab-use-after-free in mlxsw_sp_acl_ctcam_region_entry_remove+0x21d/0x230
Read of size 8 at addr ffff8881735319e8 by task kworker/0:31/3858
CPU: 0 PID: 3858 Comm: kworker/0:31 Tainted: G W 6.9.0-rc2-custom-00782-gf2275c2157d8 #5
Hardware name: Mellanox Technologies Ltd. MSN3700/VMOD0005, BIOS 5.11 01/06/2019
Workqueue: mlxsw_core mlxsw_sp_acl_tcam_vregion_rehash_work
Call Trace:
<TASK>
dump_stack_lvl+0xc6/0x120
print_report+0xce/0x670
kasan_report+0xd7/0x110
mlxsw_sp_acl_ctcam_region_entry_remove+0x21d/0x230
mlxsw_sp_acl_ctcam_entry_del+0x2e/0x70
mlxsw_sp_acl_atcam_entry_del+0x81/0x210
mlxsw_sp_acl_tcam_vchunk_migrate_all+0x3cd/0xb50
mlxsw_sp_acl_tcam_vregion_rehash_work+0x157/0x1300
process_one_work+0x8eb/0x19b0
worker_thread+0x6c9/0xf70
kthread+0x2c9/0x3b0
ret_from_fork+0x4d/0x80
ret_from_fork_asm+0x1a/0x30
</TASK>
Allocated by task 174:
kasan_save_stack+0x33/0x60
kasan_save_track+0x14/0x30
__kasan_kmalloc+0x8f/0xa0
__kmalloc+0x19c/0x360
mlxsw_sp_acl_tcam_region_create+0xdf/0x9c0
mlxsw_sp_acl_tcam_vregion_rehash_work+0x954/0x1300
process_one_work+0x8eb/0x19b0
worker_thread+0x6c9/0xf70
kthread+0x2c9/0x3b0
ret_from_fork+0x4d/0x80
ret_from_fork_asm+0x1a/0x30
Freed by task 7:
kasan_save_stack+0x33/0x60
kasan_save_track+0x14/0x30
kasan_save_free_info+0x3b/0x60
poison_slab_object+0x102/0x170
__kasan_slab_free+0x14/0x30
kfree+0xc1/0x290
mlxsw_sp_acl_tcam_region_destroy+0x272/0x310
mlxsw_sp_acl_tcam_vregion_rehash_work+0x731/0x1300
process_one_work+0x8eb/0x19b0
worker_thread+0x6c9/0xf70
kthread+0x2c9/0x3b0
ret_from_fork+0x4d/0x80
ret_from_fork_asm+0x1a/0x30
Fixes: c9c9af91f1 ("mlxsw: spectrum_acl: Allow to interrupt/continue rehash work")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Alexander Zubkov <green@qrator.net>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/3e412b5659ec2310c5c615760dfe5eac18dd7ebd.1713797103.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79b5b4b18b ]
The rule activity update delayed work periodically traverses the list of
configured rules and queries their activity from the device.
As part of this task it accesses the entry pointed by 'ventry->entry',
but this entry can be changed concurrently by the rehash delayed work,
leading to a use-after-free [1].
Fix by closing the race and perform the activity query under the
'vregion->lock' mutex.
[1]
BUG: KASAN: slab-use-after-free in mlxsw_sp_acl_tcam_flower_rule_activity_get+0x121/0x140
Read of size 8 at addr ffff8881054ed808 by task kworker/0:18/181
CPU: 0 PID: 181 Comm: kworker/0:18 Not tainted 6.9.0-rc2-custom-00781-gd5ab772d32f7 #2
Hardware name: Mellanox Technologies Ltd. MSN3700/VMOD0005, BIOS 5.11 01/06/2019
Workqueue: mlxsw_core mlxsw_sp_acl_rule_activity_update_work
Call Trace:
<TASK>
dump_stack_lvl+0xc6/0x120
print_report+0xce/0x670
kasan_report+0xd7/0x110
mlxsw_sp_acl_tcam_flower_rule_activity_get+0x121/0x140
mlxsw_sp_acl_rule_activity_update_work+0x219/0x400
process_one_work+0x8eb/0x19b0
worker_thread+0x6c9/0xf70
kthread+0x2c9/0x3b0
ret_from_fork+0x4d/0x80
ret_from_fork_asm+0x1a/0x30
</TASK>
Allocated by task 1039:
kasan_save_stack+0x33/0x60
kasan_save_track+0x14/0x30
__kasan_kmalloc+0x8f/0xa0
__kmalloc+0x19c/0x360
mlxsw_sp_acl_tcam_entry_create+0x7b/0x1f0
mlxsw_sp_acl_tcam_vchunk_migrate_all+0x30d/0xb50
mlxsw_sp_acl_tcam_vregion_rehash_work+0x157/0x1300
process_one_work+0x8eb/0x19b0
worker_thread+0x6c9/0xf70
kthread+0x2c9/0x3b0
ret_from_fork+0x4d/0x80
ret_from_fork_asm+0x1a/0x30
Freed by task 1039:
kasan_save_stack+0x33/0x60
kasan_save_track+0x14/0x30
kasan_save_free_info+0x3b/0x60
poison_slab_object+0x102/0x170
__kasan_slab_free+0x14/0x30
kfree+0xc1/0x290
mlxsw_sp_acl_tcam_vchunk_migrate_all+0x3d7/0xb50
mlxsw_sp_acl_tcam_vregion_rehash_work+0x157/0x1300
process_one_work+0x8eb/0x19b0
worker_thread+0x6c9/0xf70
kthread+0x2c9/0x3b0
ret_from_fork+0x4d/0x80
ret_from_fork_asm+0x1a/0x30
Fixes: 2bffc5322f ("mlxsw: spectrum_acl: Don't take mutex in mlxsw_sp_acl_tcam_vregion_rehash_work()")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Alexander Zubkov <green@qrator.net>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/1fcce0a60b231ebeb2515d91022284ba7b4ffe7a.1713797103.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d90cfe2056 ]
The purpose of the rehash delayed work is to reduce the number of masks
(eRPs) used by an ACL region as the eRP bank is a global and limited
resource.
This is done in three steps:
1. Creating a new set of masks and a new ACL region which will use the
new masks and to which the existing filters will be migrated to. The
new region is assigned to 'vregion->region' and the region from which
the filters are migrated from is assigned to 'vregion->region2'.
2. Migrating all the filters from the old region to the new region.
3. Destroying the old region and setting 'vregion->region2' to NULL.
Only the second steps is performed under the 'vregion->lock' mutex
although its comments says that among other things it "Protects
consistency of region, region2 pointers".
This is problematic as the first step can race with filter insertion
from user space that uses 'vregion->region', but under the mutex.
Fix by holding the mutex across the entirety of the delayed work and not
only during the second step.
Fixes: 2bffc5322f ("mlxsw: spectrum_acl: Don't take mutex in mlxsw_sp_acl_tcam_vregion_rehash_work()")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Alexander Zubkov <green@qrator.net>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/1ec1d54edf2bad0a369e6b4fa030aba64e1f124b.1713797103.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 627f9c1bb8 ]
Region identifiers can be allocated both when user space tries to insert
a new tc filter and when filters are migrated from one region to another
as part of the rehash delayed work.
There is no lock protecting the bitmap from which these identifiers are
allocated from, which is racy and leads to bad parameter errors from the
device's firmware.
Fix by converting the bitmap to IDA which handles its own locking. For
consistency, do the same for the group identifiers that are part of the
same structure.
Fixes: 2bffc5322f ("mlxsw: spectrum_acl: Don't take mutex in mlxsw_sp_acl_tcam_vregion_rehash_work()")
Reported-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Alexander Zubkov <green@qrator.net>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/ce494b7940cadfe84f3e18da7785b51ef5f776e3.1713797103.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1267f7223b ]
mlxsw driver uses 'unsigned int' for reference counters in several
structures. Instead, use refcount_t type which allows us to catch overflow
and underflow issues. Change the type of the counters and use the
appropriate API.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Stable-dep-of: 627f9c1bb8 ("mlxsw: spectrum_acl_tcam: Fix race in region ID allocation")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ea7b72d4f ]
Since kfree_rcu, which is called in the hlist_for_each_entry_rcu traversal
of ovs_ct_limit_exit, is not part of the RCU read critical section, it
is possible that the RCU grace period will pass during the traversal and
the key will be free.
To prevent this, it should be changed to hlist_for_each_entry_safe.
Fixes: 11efd5cb04 ("openvswitch: Support conntrack zone limit")
Signed-off-by: Hyunwoo Kim <v4bel@theori.io>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Link: https://lore.kernel.org/r/ZiYvzQN/Ry5oeFQW@v4bel-B760M-AORUS-ELITE-AX
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e10d3ba4d4 ]
It was observed in the wild that pairs of consecutive packets would leave
the IPVS with the same wrong checksum, and the issue only went away when
disabling GSO.
IPVS needs to avoid computing the SCTP checksum when using GSO.
Fixes: 90017accff ("sctp: Add GSO support")
Co-developed-by: Firo Yang <firo.yang@suse.com>
Signed-off-by: Ismael Luceno <iluceno@suse.de>
Tested-by: Andreas Taschner <andreas.taschner@suse.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 88cd6e6b2d ]
Since the d883a4669a be introduced in v6.4, bluetooth daemon
got the following failed message of MGMT_OP_REMOVE_ADV_MONITOR
command when controller is power-off:
bluetoothd[20976]:
src/adapter.c:reset_adv_monitors_complete() Failed to reset Adv
Monitors: Failed>
Normally this situation is happened when the bluetoothd deamon
be started manually after system booting. Which means that
bluetoothd received MGMT_EV_INDEX_ADDED event after kernel
runs hci_power_off().
Base on doc/mgmt-api.txt, the MGMT_OP_REMOVE_ADV_MONITOR command
can be used when the controller is not powered. This patch changes
the code in remove_adv_monitor() to use hci_cmd_sync_submit()
instead of hci_cmd_sync_queue().
Fixes: d883a4669a ("Bluetooth: hci_sync: Only allow hci_cmd_sync_queue if running")
Cc: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Cc: Manish Mandlik <mmandlik@google.com>
Cc: Archie Pusaka <apusaka@chromium.org>
Cc: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Chun-Yi Lee <jlee@suse.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 18bdb386a1 ]
hci_devcd_append() would free the skb on error so the caller don't
have to free it again otherwise it would cause the double free of skb.
Fixes: 0b70151328 ("Bluetooth: btusb: mediatek: add MediaTek devcoredump support")
Reported-by : Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6eb5fcc416 ]
These commands don't require the adapter to be up and running so don't
use hci_cmd_sync_queue which would check that flag, instead use
hci_cmd_sync_submit which would ensure mgmt_class_complete is set
properly regardless if any command was actually run or not.
Link: https://github.com/bluez/bluez/issues/809
Fixes: d883a4669a ("Bluetooth: hci_sync: Only allow hci_cmd_sync_queue if running")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9a830a676 ]
The code shall always check if HCI_QUIRK_BROKEN_READ_ENC_KEY_SIZE has
been set before attempting to use HCI_OP_READ_ENC_KEY_SIZE.
Fixes: c569242cd4 ("Bluetooth: hci_event: set the conn encrypted before conn establishes")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b23d98d46d ]
btusb_coredump_qca() uses __hci_cmd_sync() to send a vendor-specific
command to trigger firmware coredump, but the command does not
have any event as its sync response, so it is not suitable to use
__hci_cmd_sync(), fixed by using __hci_cmd_send().
Fixes: 20981ce2d5 ("Bluetooth: btusb: Add WCN6855 devcoredump support")
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d806f474a9 ]
The controller has several register bits describing access control
information for a given GPIO pin. When SCR_SEC_[R|W]EN is unset, it
means we have full read/write access to all the registers for given GPIO
pin. When SCR_SEC[R|W]EN is set, it means we need to further check the
accompanying SCR_SEC_G1[R|W] bit to determine read/write access to all
the registers for given GPIO pin.
This check was previously declaring that a GPIO pin was accessible
only if either of the following conditions were met:
- SCR_SEC_REN + SCR_SEC_WEN both set
or
- SCR_SEC_REN + SCR_SEC_WEN both set and
SCR_SEC_G1R + SCR_SEC_G1W both set
Update the check to properly handle cases where only one of
SCR_SEC_REN or SCR_SEC_WEN is set.
Fixes: b2b56a1632 ("gpio: tegra186: Check GPIO pin permission before access.")
Signed-off-by: Prathamesh Shete <pshete@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20240424095514.24397-1-pshete@nvidia.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5b5f724b05 ]
Only blink if the link is up on a LED which is programmed to also
indicate link-status.
Otherwise, if both LEDs are in use to indicate different speeds, the
resulting blinking being inverted on LEDs which aren't switched on at
a specific speed is quite counter-intuitive.
Also make sure that state left behind by reset or the bootloader is
recognized correctly including the half-duplex and full-duplex bits as
well as the (unsupported by Linux netdev trigger semantics) link-down
bit.
Fixes: c66937b0f8 ("net: phy: mediatek-ge-soc: support PHY LEDs")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2a904107e ]
Since call_rcu, which is called in the hlist_for_each_entry_rcu traversal
of gtp_dellink, is not part of the RCU read critical section, it
is possible that the RCU grace period will pass during the traversal and
the key will be free.
To prevent this, it should be changed to hlist_for_each_entry_safe.
Fixes: 94dc550a50 ("gtp: fix an use-after-free in ipv4_pdp_find()")
Signed-off-by: Hyunwoo Kim <v4bel@theori.io>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3584718cf2 ]
Jonathan Heathcote reported a regression caused by blamed commit
on aarch64 architecture.
x86 happens to have irq-safe __this_cpu_add_return()
and __this_cpu_sub(), but this is not generic.
I think my confusion came from "struct sock" argument,
because these helpers are called with a locked socket.
But the memory accounting is per-proto (and per-cpu after
the blamed commit). We might cleanup these helpers later
to directly accept a "struct proto *proto" argument.
Switch to this_cpu_add_return() and this_cpu_xchg()
operations, and get rid of preempt_disable()/preempt_enable() pairs.
Fast path becomes a bit faster as a result :)
Many thanks to Jonathan Heathcote for his awesome report and
investigations.
Fixes: 3cd3399dd7 ("net: implement per-cpu reserves for memory_allocated")
Reported-by: Jonathan Heathcote <jonathan.heathcote@bbc.co.uk>
Closes: https://lore.kernel.org/netdev/VI1PR01MB42407D7947B2EA448F1E04EFD10D2@VI1PR01MB4240.eurprd01.prod.exchangelabs.com/
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Shakeel Butt <shakeel.butt@linux.dev>
Link: https://lore.kernel.org/r/20240421175248.1692552-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 12a686c2e7 ]
This patch adds /proc/sys/net/core/mem_pcpu_rsv sysctl file,
to make SK_MEMORY_PCPU_RESERV tunable.
Commit 3cd3399dd7 ("net: implement per-cpu reserves for
memory_allocated") introduced per-cpu forward alloc cache:
"Implement a per-cpu cache of +1/-1 MB, to reduce number
of changes to sk->sk_prot->memory_allocated, which
would otherwise be cause of false sharing."
sk_prot->memory_allocated points to global atomic variable:
atomic_long_t tcp_memory_allocated ____cacheline_aligned_in_smp;
If increasing the per-cpu cache size from 1MB to e.g. 16MB,
changes to sk->sk_prot->memory_allocated can be further reduced.
Performance may be improved on system with many cores.
Signed-off-by: Adam Li <adamli@os.amperecomputing.com>
Reviewed-by: Christoph Lameter (Ampere) <cl@linux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 3584718cf2 ("net: fix sk_memory_allocated_{add|sub} vs softirqs")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6bea4f03c6 ]
During module probe, regulator 'vin' and 'vdd-io' are used and enabled,
but the vdd-io regulator overwrites the 'vin' regulator pointer. During
remove, only the vdd-io is disabled, as the vin regulator pointer is not
available anymore. When regulator_put() is called during resource
cleanup a kernel warning is given, as the regulator is still enabled.
Store the two regulators in separate pointers and disable both the
regulators on module remove.
Fixes: 49d22c70aa ("NFC: trf7970a: Add device tree option of 1.8 Volt IO voltage")
Signed-off-by: Paul Geurts <paul_geurts@live.nl>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/DB7PR09MB26847A4EBF88D9EDFEB1DA0F950E2@DB7PR09MB2684.eurprd09.prod.outlook.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a4e3899065 ]
With the recent PHYLINK changes requiring supported_interfaces to be set,
MV88E6250 family switches like the 88E6020 fail to probe - cmode is
never initialized on these devices, so mv88e6250_phylink_get_caps() does
not set any supported_interfaces flags.
Instead of a cmode, on 88E6250 we have a read-only port mode value that
encodes similar information. There is no reason to bother mapping port
mode to the cmodes of other switch models; instead we introduce a
mv88e6250_setup_supported_interfaces() that is called directly from
mv88e6250_phylink_get_caps().
Fixes: de5c9bf40c ("net: phylink: require supported_interfaces to be filled")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20240417103737.166651-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b759dd576 ]
A recent change to cxl_mem_get_records_log() [1] highlighted a subtle
nuance of looping calls to cxl_internal_send_cmd(), i.e. that
cxl_internal_send_cmd() modifies the 'size_out' member of the @mbox_cmd
argument. That mechanism is useful for communicating underflow, but it
is unwanted when reusing @mbox_cmd for a subsequent submission. It turns
out that cxl_xfer_log() avoids this scenario by always redefining
@mbox_cmd each iteration.
Update cxl_mem_get_records_log() and cxl_mem_get_poison() to follow the
same style as cxl_xfer_log(), i.e. re-define @mbox_cmd each iteration.
The cxl_mem_get_records_log() change is just a style fixup, but the
cxl_mem_get_poison() change is a potential fix, per Alison [2]:
Poison list retrieval can hit this case if the MORE flag is set and
a follow on read of the list delivers more records than the previous
read. ie. device gives one record, sets the _MORE flag, then gives 5.
Not an urgent fix since this behavior has not been seen in the wild,
but worth tracking as a fix.
Cc: Kwangjin Ko <kwangjin.ko@sk.com>
Cc: Alison Schofield <alison.schofield@intel.com>
Fixes: ed83f7ca39 ("cxl/mbox: Add GET_POISON_LIST mailbox command")
Link: http://lore.kernel.org/r/20240402081404.1106-2-kwangjin.ko@sk.com [1]
Link: http://lore.kernel.org/r/ZhAhAL/GOaWFrauw@aschofie-mobl2 [2]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Alison Schofield <alison.schofield@intel.com>
Link: https://lore.kernel.org/r/171235441633.2716581.12330082428680958635.stgit@dwillia2-xfh.jf.intel.com
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a1acdc226b ]
We do not support two simultaneous recoveries so check for reset
flag, BNXT_STATE_IN_FW_RESET, and do not proceed with AER further.
When the pci channel state is pci_channel_io_frozen, the PCIe link
can not be trusted so we disable the traffic immediately and stop
BAR access by calling bnxt_fw_fatal_close(). BAR access after
AER fatal error can cause an NMI.
Fixes: f75d9a0aa9 ("bnxt_en: Re-write PCI BARs after PCI fatal error.")
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7474b1c82b ]
Introduce bnxt_fw_fatal_close() API which can be used
to stop data path and disable device when firmware
is in fatal state.
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: a1acdc226b ("bnxt_en: Fix the PCI-AER routines")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c58e88d490 ]
First problem is a double call to __in_dev_get_rcu(), because
the second one could return NULL.
if (__in_dev_get_rcu(dev) && __in_dev_get_rcu(dev)->ifa_list)
Second problem is a read from dev->ip6_ptr with no NULL check:
if (!list_empty(&rcu_dereference(dev->ip6_ptr)->addr_list))
Use the correct RCU API to fix these.
v2: add missing include <net/addrconf.h>
Fixes: d329ea5bd8 ("icmp: add response to RFC 8335 PROBE messages")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Andreas Roeseler <andreas.a.roeseler@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e027b71762 ]
By checking the pmic node with microchip,mcp16502.yaml#
'regulator-suspend-voltage' does not match any of the
regexes 'pinctrl-[0-9]+' from schema microchip,mcp16502.yaml#
which inherits regulator.yaml#. So replace regulator-suspend-voltage
with regulator-suspend-microvolt to avoid the inconsitency.
Fixes: 85b1304b9d ("ARM: dts: at91: sama7g5ek: set regulator voltages for standby state")
Signed-off-by: Andrei Simion <andrei.simion@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20240404123824.19182-2-andrei.simion@microchip.com
[claudiu.beznea: added a dot before starting the last sentence in commit
description]
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e2050a836 ]
The driver queries the Management Capabilities Mask (MCAM) register
during initialization to understand if it can read up to 128 bytes from
transceiver modules.
However, not all firmware versions support this register, leading to the
driver failing to load.
Fix by treating an error in the register query as an indication that the
feature is not supported.
Fixes: 1f4aea1f72 ("mlxsw: core_env: Read transceiver module EEPROM in 128 bytes chunks")
Reported-by: Tim 'mithro' Ansell <me@mith.ro>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/0afa8b2e8bac178f5f88211344429176dcc72281.1713446092.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 976c44af48 ]
The device's manual (PRM - Programmer's Reference Manual) classifies the
trap that is used to deliver EMAD responses as an "event trap". Among
other things, it means that the only actions that can be associated with
the trap are TRAP and FORWARD (NOP).
Currently, during driver de-initialization the driver unregisters the
trap by setting its action to DISCARD, which violates the above
guideline. Future firmware versions will prevent such misuses by
returning an error. This does not prevent the driver from working, but
an error will be printed to the kernel log during module removal /
devlink reload:
mlxsw_spectrum 0000:03:00.0: Reg cmd access status failed (status=7(bad parameter))
mlxsw_spectrum 0000:03:00.0: Reg cmd access failed (reg_id=7003(hpkt),type=write)
Suppress the error message by aligning the driver to the manual and use
a FORWARD (NOP) action when unregistering the trap.
Fixes: 4ec14b7634 ("mlxsw: Add interface to access registers and process events")
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Link: https://lore.kernel.org/r/753a89e14008fde08cb4a2c1e5f537b81d8eb2d6.1713446092.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f58f45c1e5 ]
The VXLAN driver currently does not check if the inner layer2
source-address is valid.
In case source-address snooping/learning is enabled, a entry in the FDB
for the invalid address is created with the layer3 address of the tunnel
endpoint.
If the frame happens to have a non-unicast address set, all this
non-unicast traffic is subsequently not flooded to the tunnel network
but sent to the learnt host in the FDB. To make matters worse, this FDB
entry does not expire.
Apply the same filtering for packets as it is done for bridges. This not
only drops these invalid packets but avoids them from being learnt into
the FDB.
Fixes: d342894c5d ("vxlan: virtual extensible lan")
Suggested-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69197dfc64 ]
driver needs queue msix vectors and one misc irq vector,
but only queue vectors need irq affinity.
when num_online_cpus is less than chip max msix vectors,
driver will acquire (num_online_cpus + 1) vecotrs, and
call pci_alloc_irq_vectors_affinity functions with affinity
params without setting pre_vectors or post_vectors, it will
cause return error code -ENOSPC.
Misc irq vector is vector 0, driver need to set affinity params
.pre_vectors = 1.
Fixes: 3f70318611 ("net: libwx: Add irq flow functions")
Signed-off-by: Duanqiang Wen <duanqiangwen@net-swift.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb55e08dba ]
If the AP removal timer is long, we don't really want to
remove the link immediately. However, we really should do
it _before_ the AP removes it (which happens at or after
count reaches 0), so subtract 1 from the countdown when
scheduling the timer. This causes the link removal work
to run just after the beacon with value 1 is received. If
the counter is already zero, do it immediately.
This fixes an issue where we do the removal too late and
receive a beacon from the AP that's no longer associated
with the MLD, but thus removed EHT and ML elements, and
then we disconnect instead from the whole MLD, since one
of the associated APs changed mode from EHT to HE.
Fixes: 8eb8dd2ffb ("wifi: mac80211: Support link removal using Reconfiguration ML element")
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240418105220.03ac4a09fa74.Ifb8c8d38e3402721a81ce5981568f47b5c5889cb@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c75cdcdf8 ]
Depending on the origin of the packets (and their SA), 802.11 + mesh headers
could be filled in differently. In order to properly deal with that, add a
new field to the lookup key, indicating the type (local, proxied or
forwarded). This can fix spurious packet drop issues that depend on the order
in which nodes/hosts communicate with each other.
Fixes: d5edb9ae8d ("wifi: mac80211: mesh fast xmit support")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://msgid.link/20240415121811.13391-1-nbd@nbd.name
[use sizeof_field() for key_len]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ba4b1fa312 ]
The assignment to pointer cache in function mesh_fast_tx_gc can
be made at the declaration time rather than a later assignment.
There are also 3 functions where pointer cache is being initialized
at declaration time and later re-assigned again with the same
value, these are redundant and can be removed.
Cleans up code and three clang scan build warnings:
warning: Value stored to 'cache' during its initialization is never
read [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://msgid.link/20240215232151.2075483-1-colin.i.king@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Stable-dep-of: 8c75cdcdf8 ("wifi: mac80211: split mesh fast tx cache into local/proxied/forwarded")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61231eb811 ]
"gmac" node stands for just an ordinary Ethernet controller,
which is by no means a provider of interrupts, i.e. it doesn't serve
as an interrupt controller, thus "#interrupt-cells" property doesn't
belong to it and so we remove it.
Fixes:
------------>8------------
DTC arch/arc/boot/dts/hsdk.dtb
arch/arc/boot/dts/hsdk.dts:207.23-235.5: Warning (interrupt_provider): /soc/ethernet@8000: '#interrupt-cells' found, but node is not an interrupt provider
arch/arc/boot/dts/hsdk.dtb: Warning (interrupt_map): Failed prerequisite 'interrupt_provider'
------------>8------------
Reported-by: Vineet Gupta <vgupta@kernel.org>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7d045025a2 ]
IRQ chip data contains a pointer to the GPIO chip. Luckily we have
the pointers the same, but strictly speaking it's not guaranteed.
Even though, still better to fix this.
Fixes: ccf6fd6dcc ("gpio: merrifield: Introduce GPIO driver to support Merrifield")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ecda830909 ]
The ACPI DSDT of the Surface Pro X (SQ2) specifies the interrupts for
the secondary UBS controller as
Name (_CRS, ResourceTemplate ()
{
Interrupt (ResourceConsumer, Level, ActiveHigh, Shared, ,, )
{
0x000000AA,
}
Interrupt (ResourceConsumer, Level, ActiveHigh, SharedAndWake, ,, )
{
0x000000A7, // hs_phy_irq: &intc GIC_SPI 136
}
Interrupt (ResourceConsumer, Level, ActiveHigh, SharedAndWake, ,, )
{
0x00000228, // ss_phy_irq: &pdc 40
}
Interrupt (ResourceConsumer, Edge, ActiveHigh, SharedAndWake, ,, )
{
0x0000020A, // dm_hs_phy_irq: &pdc 10
}
Interrupt (ResourceConsumer, Edge, ActiveHigh, SharedAndWake, ,, )
{
0x0000020B, // dp_hs_phy_irq: &pdc 11
}
})
Generally, the interrupts above 0x200 map to the PDC interrupts (as used
in the devicetree) as ACPI_NUMBER - 0x200. Note that this lines up with
dm_hs_phy_irq and dp_hs_phy_irq (as well as the interrupts for the
primary USB controller).
Based on the snippet above, ss_phy_irq should therefore be PDC 40 (=
0x28) and not PDC 7. The latter is according to ACPI instead used as
ss_phy_irq for port 0 of the multiport USB controller). Fix this by
setting ss_phy_irq to '&pdc 40'.
Fixes: b080f53a8f ("arm64: dts: qcom: sc8180x: Add remoteprocs, wifi and usb nodes")
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20240328022224.336938-1-luzmaximilian@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 433d54818f ]
With default dts configuration for BPI-R2Pro, the regulator for sd card is
powered off when reboot is commanded, and the only solution to detect the
sd card again, and therefore, allow rebooting from there, is to do a
hardware reset.
Configure the regulator for sd to be always on for BPI-R2Pro in order to
avoid this issue.
Fixes: f901aaadaa ("arm64: dts: rockchip: Add Bananapi R2 Pro")
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Link: https://lore.kernel.org/r/20240305143222.189413-1-jtornosm@redhat.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43853e843a ]
Remove a redundant node from the Pine64 Pinebook Pro dts, which is intended
to provide a value for the delay in PCI Express enumeration, but that isn't
supported without additional out-of-tree kernel patches.
There were already efforts to upstream those kernel patches, because they
reportedly make some PCI Express cards (such as LSI SAS HBAs) usable in
Pine64 RockPro64 (which is also based on the RK3399); otherwise, those PCI
Express cards fail to enumerate. However, providing the required background
and explanations proved to be a tough nut to crack, which is the reason why
those patches remain outside of the kernel mainline for now.
If those out-of-tree patches eventually become upstreamed, the resulting
device-tree changes will almost surely belong to the RK3399 SoC dtsi. Also,
the above-mentioned unusable-without-out-of-tree-patches PCI Express devices
are in all fairness not usable in a Pinebook Pro without some extensive
hardware modifications, which is another reason to delete this redundant
node. When it comes to the Pinebook Pro, only M.2 NVMe SSDs can be installed
out of the box (using an additional passive adapter PCB sold separately by
Pine64), which reportedly works fine with no additional patches.
Fixes: 5a65505a69 ("arm64: dts: rockchip: Add initial support for Pinebook Pro")
Signed-off-by: Dragan Simic <dsimic@manjaro.org>
Link: https://lore.kernel.org/r/0f82c3f97cb798d012270d13b34d8d15305ef293.1711923520.git.dsimic@manjaro.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 945a7c8570 ]
The PCIE_WAKE# has a diode used as a level-shifter, and is used as an
input pin. While the SoC default is to enable the pull-up, the core
rk3399 pinconf for this pin opted for pull-none. So as to not disturb
the behaviour of other boards which may rely on pull-none instead of
pull-up, set the needed pull-up only for RK3399 Puma.
Fixes: 60fd9f72ce ("arm64: dts: rockchip: add Haikou baseboard with RK3399-Q7 SoM")
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Link: https://lore.kernel.org/r/20240308-puma-diode-pu-v2-2-309f83da110a@theobroma-systems.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a2ac2a1b02 ]
The MT7531 switch listens on PHY address 0x1f on an MDIO bus. I've got two
findings that support this. There's no bootstrapping option to change the
PHY address of the switch. The Linux driver hardcodes 0x1f as the PHY
address of the switch. So the reg property on the device tree is currently
ignored by the Linux driver.
Therefore, describe the correct PHY address on Banana Pi BPI-R2 Pro that
has this switch.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Fixes: c1804463e5 ("arm64: dts: rockchip: Add mt7531 dsa node to BPI-R2-Pro board")
Link: https://lore.kernel.org/r/20240314-for-rockchip-mt7531-phy-address-v1-1-743b5873358f@arinc9.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21f28a7eb7 ]
You can bind whatever action you want to the mouse's reprogrammable
buttons using Windows application. Allow Linux to receive multimedia keycodes.
Fixes: 3ed224e273 ("HID: logitech-dj: Fix 064d:c52f receiver support")
Signed-off-by: Yaraslau Furman <yaro330@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92826905ae ]
The variable dev->devc in ish_dev_init was utilized by dev_err before it
was properly assigned. To rectify this, the assignment of dev->devc has
been moved to immediately follow memory allocation.
Without this change "(NULL device *)" is printed for device information.
Fixes: 8ae2f2b0a2 ("HID: intel-ish-hid: ipc: Fix potential use-after-free in work function")
Fixes: ae02e5d40d ("HID: intel-ish-hid: ipc layer")
Signed-off-by: Zhang Lixu <lixu.zhang@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77d8aa79ec ]
forceuid/forcegid should be enabled by default when uid=/gid= options are
specified, but commit 24e0a1eff9 ("cifs: switch to new mount api")
changed the behavior. Due to the change, a mounted share does not show
intentional uid/gid for files and directories even though uid=/gid=
options are specified since forceuid/forcegid are not enabled.
This patch reinstates original behavior that overrides uid/gid with
specified uid/gid by the options.
Fixes: 24e0a1eff9 ("cifs: switch to new mount api")
Signed-off-by: Takayuki Nagata <tnagata@redhat.com>
Acked-by: Paulo Alcantara (Red Hat) <pc@manguebit.com>
Acked-by: Ronnie Sahlberg <lsahlber@redhat.com>
Acked-by: Tom Talpey <tom@talpey.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 18d86965e3 ]
After commit 2c7d399e55 ("smb: client: reuse file lease key in
compound operations") the client started reusing lease keys for
rename, unlink and set path size operations to prevent it from
breaking its own leases and thus causing unnecessary lease breaks to
same connection.
The implementation relies on positive dentries and
cifsInodeInfo::lease_granted to decide whether reusing lease keys for
the compound requests. cifsInodeInfo::lease_granted was introduced by
commit 0ab95c2510 ("Defer close only when lease is enabled.") to
indicate whether lease caching is granted for a specific file, but
that can only happen until file is open, so
cifsInodeInfo::lease_granted was left uninitialised in ->alloc_inode
and then client started sending random lease keys for files that
hadn't any leases.
This fixes the following test case against samba:
mount.cifs //srv/share /mnt/1 -o ...,nosharesock
mount.cifs //srv/share /mnt/2 -o ...,nosharesock
touch /mnt/1/foo; tail -f /mnt/1/foo & pid=$!
mv /mnt/2/foo /mnt/2/bar # fails with -EIO
kill $pid
Fixes: 0ab95c2510 ("Defer close only when lease is enabled.")
Signed-off-by: Paulo Alcantara (Red Hat) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dad80c6bff ]
During mount, cifs_mount_get_tcon() gets a tcon resource connection record
and then attaches an fscache volume cookie to it. However, it does this
irrespective of whether or not the tcon returned from cifs_get_tcon() is a
new record or one that's already in use. This leads to a warning about a
volume cookie collision and a leaked volume cookie because tcon->fscache
gets reset.
Fix this be adding a mutex and a "we've already tried this" flag and only
doing it once for the lifetime of the tcon.
[!] Note: Looking at cifs_mount_get_tcon(), a more general solution may
actually be required. Reacquiring the volume cookie isn't the only thing
that function does: it also partially reinitialises the tcon record without
any locking - which may cause live filesystem ops already using the tcon
through a previous mount to malfunction.
This can be reproduced simply by something like:
mount //example.com/test /xfstest.test -o user=shares,pass=xxx,fsc
mount //example.com/test /mnt -o user=shares,pass=xxx,fsc
Fixes: 70431bfd82 ("cifs: Support fscache indexing rewrite")
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Paulo Alcantara (Red Hat) <pc@manguebit.com>
cc: Shyam Prasad N <sprasad@microsoft.com>
cc: linux-cifs@vger.kernel.org
cc: linux-fsdevel@vger.kernel.org
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
in-tech smart charging is now called chargebyte. Our product name
seems to be more stable than our company name, so drop them
where it's possible.
Signed-off-by: Stefan Wahren <stefan.wahren@chargebyte.com>
Adds a shutdown function to turn off the backlight, bridge, and
touch controller on shutdown.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The TC358762 bridge and panel decodes the mode differently on
DSI0 to DSI1 for no obvious reason, and results in a shift off
the screen.
Whilst it would be possible to change the compatible used for
the panel, that then messes up Pi5.
As it appears to be restricted to vc4 DSI0, fix up the mode
in vc4_dsi.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The Toshiba bridge is very fussy and doesn't like the CM3
output when being told to produce a 27.777MHz pixel clock, which
is an almost perfect match to the DSI link integer divider.
Increasing to 30MHz will switch the DSI link from 333MHz to 400MHz
and makes the bridge happy with the same video timing as works
on Pi4.
(Pi4 will be using a link frequency of 375MHz due to a 3GHz
parent PLL).
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The 7inch panel is one line off the screen both horizontally
and vertically.
Alter the panel mode to correct this.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
PLLD is considered more stable than PLLA as it doesn't get varied.
The clock muxing has been updated to driver DSI0 from PLLD, so
update DT to match.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
DSI0 can take the clock from either PLLA or PLLD. PLLA is
the default muxing, but PLLD is considered the more stable.
Switch to using PLLD.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The pixel to byte FIFO appears to not always reset correctly,
which can lead to colour errors and/or horizontal shifts.
Reset on every vblank to work around the issue.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
DSI0 is misbehaving and needs to action things on vblank to
work around it.
Add a new hook to call across during vblank.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The block must be enabled for the FIFO resets to be actioned,
so ensure this is the case.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The initialisation sequence differs slightly from the documentation
in that the clocks are meant to be running before resets and
similar.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reverts 8a4b2fc9c9 ("drm/bridge: tc358762: Split register programming from pre-enable to enable")
as we want the config commands sent before video starts.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The autodetection of resolution/timing by the TC358762 can lead
to the display being shifted by a pixel or two.
Program the TC358762 with the requested mode timing so that
it can reproduce it accurately.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
xHCI caches device and endpoint data after the interface is configured,
so an explicit command needs to be issued for any device driver wanting
to alter the polling interval of an endpoint.
Add usb_fixup_endpoint() to allow drivers to do this. The fixup must be
called after calculating endpoint bandwidth requirements but before any
URBs are submitted.
If polling intervals are shortened, any bandwidth reservations are no
longer valid but in practice polling intervals are only ever relaxed.
Limit the scope to interrupt transfers for now.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
commit 8cf9926c53 upstream.
There is no need to reset the USB4 host routers on resume because they
are reset already and this may cause problems if the link does not come
up soon enough. For this reason limit this to happen in non-USB4 host
routers only (that's Apple systems with Intel Thunderbolt controllers).
Fixes: 59a54c5f3d ("thunderbolt: Reset topology created by the boot firmware")
Cc: Sanath S <Sanath.S@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1e56086415 upstream.
A last minute revert in 6.7-final introduced a potential deadlock when
enabling ASPM during probe of Qualcomm PCIe controllers as reported by
lockdep:
============================================
WARNING: possible recursive locking detected
6.7.0 #40 Not tainted
--------------------------------------------
kworker/u16:5/90 is trying to acquire lock:
ffffacfa78ced000 (pci_bus_sem){++++}-{3:3}, at: pcie_aspm_pm_state_change+0x58/0xdc
but task is already holding lock:
ffffacfa78ced000 (pci_bus_sem){++++}-{3:3}, at: pci_walk_bus+0x34/0xbc
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(pci_bus_sem);
lock(pci_bus_sem);
*** DEADLOCK ***
Call trace:
print_deadlock_bug+0x25c/0x348
__lock_acquire+0x10a4/0x2064
lock_acquire+0x1e8/0x318
down_read+0x60/0x184
pcie_aspm_pm_state_change+0x58/0xdc
pci_set_full_power_state+0xa8/0x114
pci_set_power_state+0xc4/0x120
qcom_pcie_enable_aspm+0x1c/0x3c [pcie_qcom]
pci_walk_bus+0x64/0xbc
qcom_pcie_host_post_init_2_7_0+0x28/0x34 [pcie_qcom]
The deadlock can easily be reproduced on machines like the Lenovo ThinkPad
X13s by adding a delay to increase the race window during asynchronous
probe where another thread can take a write lock.
Add a new pci_set_power_state_locked() and associated helper functions that
can be called with the PCI bus semaphore held to avoid taking the read lock
twice.
Link: https://lore.kernel.org/r/ZZu0qx2cmn7IwTyQ@hovoldconsulting.com
Link: https://lore.kernel.org/r/20240130100243.11011-1-johan+linaro@kernel.org
Fixes: f93e71aea6 ("Revert "PCI/ASPM: Remove pcie_aspm_pm_state_change()"")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: <stable@vger.kernel.org> # 6.7
[bhelgaas: backported to v6.6.y, which contains 8cc22ba3f7 ("Revert
"PCI/ASPM: Remove pcie_aspm_pm_state_change()""), a backport of
f93e71aea6. This omits the drivers/pci/controller/dwc/pcie-qcom.c hunk
that updates qcom_pcie_enable_aspm(), which was added by 9f4f3dfad8
("PCI: qcom: Enable ASPM for platforms supporting 1.9.0 ops"), which is not
present in v6.6.28.]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0268a7cc7f upstream.
4byte padding cause the connection issue with the applications of MacOS.
smb2_close response size increases by 4 bytes by padding, And the smb
client of MacOS check it and stop the connection. This patch use
struct_group_attr instead of struct_group for network_open_info to use
__packed to avoid padding.
Fixes: 0015eb6e12 ("smb: client, common: fix fortify warnings")
Cc: stable@vger.kernel.org
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4973b04d3e upstream.
File overwrite case is explicitly handled, so it is not necessary to
pass RENAME_NOREPLACE to vfs_rename.
Clearing the flag fixes rename operations when the share is a ntfs-3g
mount. The latter uses an older version of fuse with no support for
flags in the ->rename op.
Cc: stable@vger.kernel.org
Signed-off-by: Marios Makassikis <mmakassikis@freebox.fr>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 17cf0c2794 upstream.
The response buffer should be allocated in smb2_allocate_rsp_buf
before validating request. But the fields in payload as well as smb2 header
is used in smb2_allocate_rsp_buf(). This patch add simple buffer size
validation to avoid potencial out-of-bounds in request buffer.
Cc: stable@vger.kernel.org
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c119f4ede3 upstream.
If ->ProtocolId is SMB2_TRANSFORM_PROTO_NUM, smb2 request size
validation could be skipped. if request size is smaller than
sizeof(struct smb2_query_info_req), slab-out-of-bounds read can happen in
smb2_allocate_rsp_buf(). This patch allocate response buffer after
decrypting transform request. smb3_decrypt_req() will validate transform
request size and avoid slab-out-of-bound in smb2_allocate_rsp_buf().
Reported-by: Norbert Szetei <norbert@doyensec.com>
Cc: stable@vger.kernel.org
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea73179e64 upstream.
Michael reported that we are seeing an ftrace bug on bootup when KASAN
is enabled and we are using -fpatchable-function-entry:
ftrace: allocating 47780 entries in 18 pages
ftrace-powerpc: 0xc0000000020b3d5c: No module provided for non-kernel address
------------[ ftrace bug ]------------
ftrace faulted on modifying
[<c0000000020b3d5c>] 0xc0000000020b3d5c
Initializing ftrace call sites
ftrace record flags: 0
(0)
expected tramp: c00000000008cef4
------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at kernel/trace/ftrace.c:2180 ftrace_bug+0x3c0/0x424
Modules linked in:
CPU: 0 PID: 0 Comm: swapper Not tainted 6.5.0-rc3-00120-g0f71dcfb4aef #860
Hardware name: IBM pSeries (emulated by qemu) POWER9 (raw) 0x4e1202 0xf000005 of:SLOF,HEAD hv:linux,kvm pSeries
NIP: c0000000003aa81c LR: c0000000003aa818 CTR: 0000000000000000
REGS: c0000000033cfab0 TRAP: 0700 Not tainted (6.5.0-rc3-00120-g0f71dcfb4aef)
MSR: 8000000002021033 <SF,VEC,ME,IR,DR,RI,LE> CR: 28028240 XER: 00000000
CFAR: c0000000002781a8 IRQMASK: 3
...
NIP [c0000000003aa81c] ftrace_bug+0x3c0/0x424
LR [c0000000003aa818] ftrace_bug+0x3bc/0x424
Call Trace:
ftrace_bug+0x3bc/0x424 (unreliable)
ftrace_process_locs+0x5f4/0x8a0
ftrace_init+0xc0/0x1d0
start_kernel+0x1d8/0x484
With CONFIG_FTRACE_MCOUNT_USE_PATCHABLE_FUNCTION_ENTRY=y and
CONFIG_KASAN=y, compiler emits nops in functions that it generates for
registering and unregistering global variables (unlike with -pg and
-mprofile-kernel where calls to _mcount() are not generated in those
functions). Those functions then end up in INIT_TEXT and EXIT_TEXT
respectively. We don't expect to see any profiled functions in
EXIT_TEXT, so ftrace_init_nop() assumes that all addresses that aren't
in the core kernel text belongs to a module. Since these functions do
not match that criteria, we see the above bug.
Address this by having ftrace ignore all locations in the text exit
sections of vmlinux.
Fixes: 0f71dcfb4a ("powerpc/ftrace: Add support for -fpatchable-function-entry")
Cc: stable@vger.kernel.org # v6.6+
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Naveen N Rao <naveen@kernel.org>
Reviewed-by: Benjamin Gray <bgray@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20240213175410.1091313-1-naveen@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 059a49aa2e upstream.
There is a bug when setting the RSS options in virtio_net that can break
the whole machine, getting the kernel into an infinite loop.
Running the following command in any QEMU virtual machine with virtionet
will reproduce this problem:
# ethtool -X eth0 hfunc toeplitz
This is how the problem happens:
1) ethtool_set_rxfh() calls virtnet_set_rxfh()
2) virtnet_set_rxfh() calls virtnet_commit_rss_command()
3) virtnet_commit_rss_command() populates 4 entries for the rss
scatter-gather
4) Since the command above does not have a key, then the last
scatter-gatter entry will be zeroed, since rss_key_size == 0.
sg_buf_size = vi->rss_key_size;
5) This buffer is passed to qemu, but qemu is not happy with a buffer
with zero length, and do the following in virtqueue_map_desc() (QEMU
function):
if (!sz) {
virtio_error(vdev, "virtio: zero sized buffers are not allowed");
6) virtio_error() (also QEMU function) set the device as broken
vdev->broken = true;
7) Qemu bails out, and do not repond this crazy kernel.
8) The kernel is waiting for the response to come back (function
virtnet_send_command())
9) The kernel is waiting doing the following :
while (!virtqueue_get_buf(vi->cvq, &tmp) &&
!virtqueue_is_broken(vi->cvq))
cpu_relax();
10) None of the following functions above is true, thus, the kernel
loops here forever. Keeping in mind that virtqueue_is_broken() does
not look at the qemu `vdev->broken`, so, it never realizes that the
vitio is broken at QEMU side.
Fix it by not sending RSS commands if the feature is not available in
the device.
Fixes: c7114b1249 ("drivers/net/virtio_net: Added basic RSS support.")
Cc: stable@vger.kernel.org
Cc: qemu-devel@nongnu.org
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Heng Qi <hengqi@linux.alibaba.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vlad Poenaru <vlad.wing@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 06dfcd4098 upstream.
The commit 40b5d2f15c ("net: dsa: mt7530: Add support for EEE features")
brought EEE support but did not enable EEE on MT7531 switch MACs. EEE is
enabled on MT7531 switch MACs by pulling the LAN2LED0 pin low on the board
(bootstrapping), unsetting the EEE_DIS bit on the trap register, or setting
the internal EEE switch bit on the CORE_PLL_GROUP4 register. Thanks to
SkyLake Huang (黃啟澤) from MediaTek for providing information on the
internal EEE switch bit.
There are existing boards that were not designed to pull the pin low.
Because of that, the EEE status currently depends on the board design.
The EEE_DIS bit on the trap pertains to the LAN2LED0 pin which is usually
used to control an LED. Once the bit is unset, the pin will be low. That
will make the active low LED turn on. The pin is controlled by the switch
PHY. It seems that the PHY controls the pin in the way that it inverts the
pin state. That means depending on the wiring of the LED connected to
LAN2LED0 on the board, the LED may be on without an active link.
To not cause this unwanted behaviour whilst enabling EEE on all boards, set
the internal EEE switch bit on the CORE_PLL_GROUP4 register.
My testing on MT7531 shows a certain amount of traffic loss when EEE is
enabled. That said, I haven't come across a board that enables EEE. So
enable EEE on the switch MACs but disable EEE advertisement on the switch
PHYs. This way, we don't change the behaviour of the majority of the boards
that have this switch. The mediatek-ge PHY driver already disables EEE
advertisement on the switch PHYs but my testing shows that it is somehow
enabled afterwards. Disabling EEE advertisement before the PHY driver
initialises keeps it off.
With this change, EEE can now be enabled using ethtool.
Fixes: 40b5d2f15c ("net: dsa: mt7530: Add support for EEE features")
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/20240408-for-net-mt7530-fix-eee-for-mt7531-mt7988-v3-1-84fdef1f008b@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5f563c31ff upstream.
The MT7530 switch after reset initialises with a core clock frequency that
works with a 25MHz XTAL connected to it. For 40MHz XTAL, the core clock
frequency must be set to 500MHz.
The mt7530_pll_setup() function is responsible of setting the core clock
frequency. Currently, it runs on MT7530 with 25MHz and 40MHz XTAL. This
causes MT7530 switch with 25MHz XTAL to egress and ingress frames
improperly.
Introduce a check to run it only on MT7530 with 40MHz XTAL.
The core clock frequency is set by writing to a switch PHY's register.
Access to the PHY's register is done via the MDIO bus the switch is also
on. Therefore, it works only when the switch makes switch PHYs listen on
the MDIO bus the switch is on. This is controlled either by the state of
the ESW_P1_LED_1 pin after reset deassertion or modifying bit 5 of the
modifiable trap register.
When ESW_P1_LED_1 is pulled high, PHY indirect access is used. That means
accessing PHY registers via the PHY indirect access control register of the
switch.
When ESW_P1_LED_1 is pulled low, PHY direct access is used. That means
accessing PHY registers via the MDIO bus the switch is on.
For MT7530 switch with 40MHz XTAL on a board with ESW_P1_LED_1 pulled high,
the core clock frequency won't be set to 500MHz, causing the switch to
egress and ingress frames improperly.
Run mt7530_pll_setup() after PHY direct access is set on the modifiable
trap register.
With these two changes, all MT7530 switches with 25MHz and 40MHz, and
P1_LED_1 pulled high or low, will egress and ingress frames properly.
Link: 4a5dd143f2/linux-mt/drivers/net/ethernet/mediatek/gsw_mt7623.c (L1039)
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20240320-for-net-mt7530-fix-25mhz-xtal-with-direct-phy-access-v1-1-d92f605f1160@arinc9.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fff1386cc8 upstream.
Running a lot of VK CTS in parallel against nouveau, once every
few hours you might see something like this crash.
BUG: kernel NULL pointer dereference, address: 0000000000000008
PGD 8000000114e6e067 P4D 8000000114e6e067 PUD 109046067 PMD 0
Oops: 0000 [#1] PREEMPT SMP PTI
CPU: 7 PID: 53891 Comm: deqp-vk Not tainted 6.8.0-rc6+ #27
Hardware name: Gigabyte Technology Co., Ltd. Z390 I AORUS PRO WIFI/Z390 I AORUS PRO WIFI-CF, BIOS F8 11/05/2021
RIP: 0010:gp100_vmm_pgt_mem+0xe3/0x180 [nouveau]
Code: c7 48 01 c8 49 89 45 58 85 d2 0f 84 95 00 00 00 41 0f b7 46 12 49 8b 7e 08 89 da 42 8d 2c f8 48 8b 47 08 41 83 c7 01 48 89 ee <48> 8b 40 08 ff d0 0f 1f 00 49 8b 7e 08 48 89 d9 48 8d 75 04 48 c1
RSP: 0000:ffffac20c5857838 EFLAGS: 00010202
RAX: 0000000000000000 RBX: 00000000004d8001 RCX: 0000000000000001
RDX: 00000000004d8001 RSI: 00000000000006d8 RDI: ffffa07afe332180
RBP: 00000000000006d8 R08: ffffac20c5857ad0 R09: 0000000000ffff10
R10: 0000000000000001 R11: ffffa07af27e2de0 R12: 000000000000001c
R13: ffffac20c5857ad0 R14: ffffa07a96fe9040 R15: 000000000000001c
FS: 00007fe395eed7c0(0000) GS:ffffa07e2c980000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000008 CR3: 000000011febe001 CR4: 00000000003706f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
...
? gp100_vmm_pgt_mem+0xe3/0x180 [nouveau]
? gp100_vmm_pgt_mem+0x37/0x180 [nouveau]
nvkm_vmm_iter+0x351/0xa20 [nouveau]
? __pfx_nvkm_vmm_ref_ptes+0x10/0x10 [nouveau]
? __pfx_gp100_vmm_pgt_mem+0x10/0x10 [nouveau]
? __pfx_gp100_vmm_pgt_mem+0x10/0x10 [nouveau]
? __lock_acquire+0x3ed/0x2170
? __pfx_gp100_vmm_pgt_mem+0x10/0x10 [nouveau]
nvkm_vmm_ptes_get_map+0xc2/0x100 [nouveau]
? __pfx_nvkm_vmm_ref_ptes+0x10/0x10 [nouveau]
? __pfx_gp100_vmm_pgt_mem+0x10/0x10 [nouveau]
nvkm_vmm_map_locked+0x224/0x3a0 [nouveau]
Adding any sort of useful debug usually makes it go away, so I hand
wrote the function in a line, and debugged the asm.
Every so often pt->memory->ptrs is NULL. This ptrs ptr is set in
the nv50_instobj_acquire called from nvkm_kmap.
If Thread A and Thread B both get to nv50_instobj_acquire around
the same time, and Thread A hits the refcount_set line, and in
lockstep thread B succeeds at refcount_inc_not_zero, there is a
chance the ptrs value won't have been stored since refcount_set
is unordered. Force a memory barrier here, I picked smp_mb, since
we want it on all CPUs and it's write followed by a read.
v2: use paired smp_rmb/smp_wmb.
Cc: <stable@vger.kernel.org>
Fixes: be55287aa5 ("drm/nouveau/imem/nv50: embed nvkm_instobj directly into nv04_instobj")
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240411011510.2546857-1-airlied@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca7c4507ba upstream.
The majority of those where removed in the commit aed01a6804
("drm/amdgpu: Remove TTM resource->start visible VRAM condition v2")
But this one was missed because it's working on the resource and not the
BO. Since we also no longer use a fake start address for visible BOs
this will now trigger invalid mapping errors.
v2: also remove the unused variable
Signed-off-by: Christian König <christian.koenig@amd.com>
Fixes: aed01a6804 ("drm/amdgpu: Remove TTM resource->start visible VRAM condition v2")
CC: stable@vger.kernel.org
Acked-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eb4b691b91 upstream.
FUSE attempts to detect server support for statx by trying it once and
setting no_statx=1 if it fails with ENOSYS, but consider the following
scenario:
- Userspace (e.g. sh) calls stat() on a file
* succeeds
- Userspace (e.g. lsd) calls statx(BTIME) on the same file
- request_mask = STATX_BASIC_STATS | STATX_BTIME
- first pass: sync=true due to differing cache_mask
- statx fails and returns ENOSYS
- set no_statx and retry
- retry sets mask = STATX_BASIC_STATS
- now mask == cache_mask; sync=false (time_before: still valid)
- so we take the "else if (stat)" path
- "err" is still ENOSYS from the failed statx call
Fix this by zeroing "err" before retrying the failed call.
Fixes: d3045530bd ("fuse: implement statx")
Cc: stable@vger.kernel.org # v6.6
Signed-off-by: Danny Lin <danny@orbstack.dev>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f737846aa upstream.
In order to minimize code size (CONFIG_CC_OPTIMIZE_FOR_SIZE=y),
compiler might choose to make a regular function call (out-of-line) for
shmem_is_huge() instead of inlining it. When transparent hugepages are
disabled (CONFIG_TRANSPARENT_HUGEPAGE=n), it can cause compilation
error.
mm/shmem.c: In function `shmem_getattr':
./include/linux/huge_mm.h:383:27: note: in expansion of macro `BUILD_BUG'
383 | #define HPAGE_PMD_SIZE ({ BUILD_BUG(); 0; })
| ^~~~~~~~~
mm/shmem.c:1148:33: note: in expansion of macro `HPAGE_PMD_SIZE'
1148 | stat->blksize = HPAGE_PMD_SIZE;
To prevent the possible error, always inline shmem_is_huge() when
transparent hugepages are disabled.
Link: https://lkml.kernel.org/r/20240409155407.2322714-1-sumanthk@linux.ibm.com
Signed-off-by: Sumanth Korikkar <sumanthk@linux.ibm.com>
Acked-by: David Hildenbrand <david@redhat.com>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ilya Leoshkevich <iii@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07a57a338a upstream.
Tony reported that the Machine check recovery was broken in v6.9-rc1, as
he was hitting a VM_BUG_ON when injecting uncorrectable memory errors to
DRAM.
After some more digging and debugging on his side, he realized that this
went back to v6.1, with the introduction of 'commit 0d206b5d2e
("mm/swap: add swp_offset_pfn() to fetch PFN from swap entry")'. That
commit, among other things, introduced swp_offset_pfn(), replacing
hwpoison_entry_to_pfn() in its favour.
The patch also introduced a VM_BUG_ON() check for is_pfn_swap_entry(), but
is_pfn_swap_entry() never got updated to cover hwpoison entries, which
means that we would hit the VM_BUG_ON whenever we would call
swp_offset_pfn() for such entries on environments with CONFIG_DEBUG_VM
set. Fix this by updating the check to cover hwpoison entries as well,
and update the comment while we are it.
Link: https://lkml.kernel.org/r/20240407130537.16977-1-osalvador@suse.de
Fixes: 0d206b5d2e ("mm/swap: add swp_offset_pfn() to fetch PFN from swap entry")
Signed-off-by: Oscar Salvador <osalvador@suse.de>
Reported-by: Tony Luck <tony.luck@intel.com>
Closes: https://lore.kernel.org/all/Zg8kLSl2yAlA3o5D@agluck-desk3/
Tested-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Acked-by: Miaohe Lin <linmiaohe@huawei.com>
Cc: <stable@vger.kernel.org> [6.1.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c5977c95df upstream.
After UFFDIO_POISON, there can be two kinds of hugetlb pte markers, either
the POISON one or UFFD_WP one.
Allow change protection to run on a poisoned marker just like !hugetlb
cases, ignoring the marker irrelevant of the permission.
Here the two bits are mutual exclusive. For example, when install a
poisoned entry it must not be UFFD_WP already (by checking pte_none()
before such install). And it also means if UFFD_WP is set there must have
no POISON bit set. It makes sense because UFFD_WP is a bit to reflect
permission, and permissions do not apply if the pte is poisoned and
destined to sigbus.
So here we simply check uffd_wp bit set first, do nothing otherwise.
Attach the Fixes to UFFDIO_POISON work, as before that it should not be
possible to have poison entry for hugetlb (e.g., hugetlb doesn't do swap,
so no chance of swapin errors).
Link: https://lkml.kernel.org/r/20240405231920.1772199-1-peterx@redhat.com
Link: https://lore.kernel.org/r/000000000000920d5e0615602dd1@google.com
Fixes: fc71884a5f ("mm: userfaultfd: add new UFFDIO_POISON ioctl")
Signed-off-by: Peter Xu <peterx@redhat.com>
Reported-by: syzbot+b07c8ac8eee3d4d8440f@syzkaller.appspotmail.com
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Axel Rasmussen <axelrasmussen@google.com>
Cc: <stable@vger.kernel.org> [6.6+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46dad3c1e5 upstream.
We allocate memory of size 'xlen + strlen(boot_command_line) + 1' for
static_command_line, but the strings copied into static_command_line are
extra_command_line and command_line, rather than extra_command_line and
boot_command_line.
When strlen(command_line) > strlen(boot_command_line), static_command_line
will overflow.
This patch just recovers strlen(command_line) which was miss-consolidated
with strlen(boot_command_line) in the commit f5c7310ac7 ("init/main: add
checks for the return value of memblock_alloc*()")
Link: https://lore.kernel.org/all/20240412081733.35925-2-ytcoode@gmail.com/
Fixes: f5c7310ac7 ("init/main: add checks for the return value of memblock_alloc*()")
Cc: stable@vger.kernel.org
Signed-off-by: Yuntao Wang <ytcoode@gmail.com>
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 34e526cb7d upstream.
Even though the boot protocol stipulates otherwise, an exception has
been made for the EFI stub, and entering the core kernel with the MMU
enabled is permitted. This allows a substantial amount of cache
maintenance to be elided, wich is significant when fast boot times are
critical (e.g., for booting micro-VMs)
Once the initial ID map has been populated, the MMU is disabled as part
of the logic sequence that puts all system registers into a known state.
Any code that needs to execute within the window where the MMU is off is
cleaned to the PoC explicitly, which includes all of HYP text when
entering at EL2.
However, the current sequence of initializing the EL2 system registers
is not safe: HCR_EL2 is set to its nVHE initial state before SCTLR_EL2
is reprogrammed, and this means that a VHE-to-nVHE switch may occur
while the MMU is enabled. This switch causes some system registers as
well as page table descriptors to be interpreted in a different way,
potentially resulting in spurious exceptions relating to MMU
translation.
So disable the MMU explicitly first when entering in EL2 with the MMU
and caches enabled.
Fixes: 6178617038 ("efi: arm64: enter with MMU and caches enabled")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Cc: <stable@vger.kernel.org> # 6.3.x
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240415075412.2347624-6-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 49ff3b4aec upstream.
On AMD and Hygon platforms, the local APIC does not automatically set
the mask bit of the LVTPC register when handling a PMI and there is
no need to clear it in the kernel's PMI handler.
For guests, the mask bit is currently set by kvm_apic_local_deliver()
and unless it is cleared by the guest kernel's PMI handler, PMIs stop
arriving and break use-cases like sampling with perf record.
This does not affect non-PerfMonV2 guests because PMIs are handled in
the guest kernel by x86_pmu_handle_irq() which always clears the LVTPC
mask bit irrespective of the vendor.
Before:
$ perf record -e cycles:u true
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.001 MB perf.data (1 samples) ]
After:
$ perf record -e cycles:u true
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.002 MB perf.data (19 samples) ]
Fixes: a16eb25b09 ("KVM: x86: Mask LVTPC when handling a PMI")
Cc: stable@vger.kernel.org
Signed-off-by: Sandipan Das <sandipan.das@amd.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
[sean: use is_intel_compatible instead of !is_amd_or_hygon()]
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-ID: <20240405235603.1173076-3-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9e985cbf29 upstream.
Drop support for virtualizing adaptive PEBS, as KVM's implementation is
architecturally broken without an obvious/easy path forward, and because
exposing adaptive PEBS can leak host LBRs to the guest, i.e. can leak
host kernel addresses to the guest.
Bug #1 is that KVM doesn't account for the upper 32 bits of
IA32_FIXED_CTR_CTRL when (re)programming fixed counters, e.g
fixed_ctrl_field() drops the upper bits, reprogram_fixed_counters()
stores local variables as u8s and truncates the upper bits too, etc.
Bug #2 is that, because KVM _always_ sets precise_ip to a non-zero value
for PEBS events, perf will _always_ generate an adaptive record, even if
the guest requested a basic record. Note, KVM will also enable adaptive
PEBS in individual *counter*, even if adaptive PEBS isn't exposed to the
guest, but this is benign as MSR_PEBS_DATA_CFG is guaranteed to be zero,
i.e. the guest will only ever see Basic records.
Bug #3 is in perf. intel_pmu_disable_fixed() doesn't clear the upper
bits either, i.e. leaves ICL_FIXED_0_ADAPTIVE set, and
intel_pmu_enable_fixed() effectively doesn't clear ICL_FIXED_0_ADAPTIVE
either. I.e. perf _always_ enables ADAPTIVE counters, regardless of what
KVM requests.
Bug #4 is that adaptive PEBS *might* effectively bypass event filters set
by the host, as "Updated Memory Access Info Group" records information
that might be disallowed by userspace via KVM_SET_PMU_EVENT_FILTER.
Bug #5 is that KVM doesn't ensure LBR MSRs hold guest values (or at least
zeros) when entering a vCPU with adaptive PEBS, which allows the guest
to read host LBRs, i.e. host RIPs/addresses, by enabling "LBR Entries"
records.
Disable adaptive PEBS support as an immediate fix due to the severity of
the LBR leak in particular, and because fixing all of the bugs will be
non-trivial, e.g. not suitable for backporting to stable kernels.
Note! This will break live migration, but trying to make KVM play nice
with live migration would be quite complicated, wouldn't be guaranteed to
work (i.e. KVM might still kill/confuse the guest), and it's not clear
that there are any publicly available VMMs that support adaptive PEBS,
let alone live migrate VMs that support adaptive PEBS, e.g. QEMU doesn't
support PEBS in any capacity.
Link: https://lore.kernel.org/all/20240306230153.786365-1-seanjc@google.com
Link: https://lore.kernel.org/all/ZeepGjHCeSfadANM@google.com
Fixes: c59a1f106f ("KVM: x86/pmu: Add IA32_PEBS_ENABLE MSR emulation for extended PEBS")
Cc: stable@vger.kernel.org
Cc: Like Xu <like.xu.linux@gmail.com>
Cc: Mingwei Zhang <mizhang@google.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Zhang Xiong <xiong.y.zhang@intel.com>
Cc: Lv Zhiyuan <zhiyuan.lv@intel.com>
Cc: Dapeng Mi <dapeng1.mi@intel.com>
Cc: Jim Mattson <jmattson@google.com>
Acked-by: Like Xu <likexu@tencent.com>
Link: https://lore.kernel.org/r/20240307005833.827147-1-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fd706c9b16 upstream.
Add kvm_vcpu_arch.is_amd_compatible to cache if a vCPU's vendor model is
compatible with AMD, i.e. if the vCPU vendor is AMD or Hygon, along with
helpers to check if a vCPU is compatible AMD vs. Intel. To handle Intel
vs. AMD behavior related to masking the LVTPC entry, KVM will need to
check for vendor compatibility on every PMI injection, i.e. querying for
AMD will soon be a moderately hot path.
Note! This subtly (or maybe not-so-subtly) makes "Intel compatible" KVM's
default behavior, both if userspace omits (or never sets) CPUID 0x0 and if
userspace sets a completely unknown vendor. One could argue that KVM
should treat such vCPUs as not being compatible with Intel *or* AMD, but
that would add useless complexity to KVM.
KVM needs to do *something* in the face of vendor specific behavior, and
so unless KVM conjured up a magic third option, choosing to treat unknown
vendors as neither Intel nor AMD means that checks on AMD compatibility
would yield Intel behavior, and checks for Intel compatibility would yield
AMD behavior. And that's far worse as it would effectively yield random
behavior depending on whether KVM checked for AMD vs. Intel vs. !AMD vs.
!Intel. And practically speaking, all x86 CPUs follow either Intel or AMD
architecture, i.e. "supporting" an unknown third architecture adds no
value.
Deliberately don't convert any of the existing guest_cpuid_is_intel()
checks, as the Intel side of things is messier due to some flows explicitly
checking for exactly vendor==Intel, versus some flows assuming anything
that isn't "AMD compatible" gets Intel behavior. The Intel code will be
cleaned up in the future.
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-ID: <20240405235603.1173076-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe90f3967b upstream.
Many architectures' switch_mm() (e.g. arm64) do not have an smp_mb()
which the core scheduler code has depended upon since commit:
commit 223baf9d17 ("sched: Fix performance regression introduced by mm_cid")
If switch_mm() doesn't call smp_mb(), sched_mm_cid_remote_clear() can
unset the actively used cid when it fails to observe active task after it
sets lazy_put.
There *is* a memory barrier between storing to rq->curr and _return to
userspace_ (as required by membarrier), but the rseq mm_cid has stricter
requirements: the barrier needs to be issued between store to rq->curr
and switch_mm_cid(), which happens earlier than:
- spin_unlock(),
- switch_to().
So it's fine when the architecture switch_mm() happens to have that
barrier already, but less so when the architecture only provides the
full barrier in switch_to() or spin_unlock().
It is a bug in the rseq switch_mm_cid() implementation. All architectures
that don't have memory barriers in switch_mm(), but rather have the full
barrier either in finish_lock_switch() or switch_to() have them too late
for the needs of switch_mm_cid().
Introduce a new smp_mb__after_switch_mm(), defined as smp_mb() in the
generic barrier.h header, and use it in switch_mm_cid() for scheduler
transitions where switch_mm() is expected to provide a memory barrier.
Architectures can override smp_mb__after_switch_mm() if their
switch_mm() implementation provides an implicit memory barrier.
Override it with a no-op on x86 which implicitly provide this memory
barrier by writing to CR3.
Fixes: 223baf9d17 ("sched: Fix performance regression introduced by mm_cid")
Reported-by: levi.yun <yeoreum.yun@arm.com>
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> # for arm64
Acked-by: Dave Hansen <dave.hansen@linux.intel.com> # for x86
Cc: <stable@vger.kernel.org> # 6.4.x
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lore.kernel.org/r/20240415152114.59122-2-mathieu.desnoyers@efficios.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a90bca2228 upstream.
The sysfs_break_active_protection() routine has an obvious reference
leak in its error path. If the call to kernfs_find_and_get() fails then
kn will be NULL, so the companion sysfs_unbreak_active_protection()
routine won't get called (and would only cause an access violation by
trying to dereference kn->parent if it was called). As a result, the
reference to kobj acquired at the start of the function will never be
released.
Fix the leak by adding an explicit kobject_put() call when kn is NULL.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: 2afc9166f7 ("scsi: sysfs: Introduce sysfs_{un,}break_active_protection()")
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: stable@vger.kernel.org
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/8a4d3f0f-c5e3-4b70-a188-0ca433f9e6f9@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6334b8e455 upstream.
When ncm function is working and then stop usb0 interface for link down,
eth_stop() is called. At this piont, accidentally if usb transport error
should happen in usb_ep_enable(), 'in_ep' and/or 'out_ep' may not be enabled.
After that, ncm_disable() is called to disable for ncm unbind
but gether_disconnect() is never called since 'in_ep' is not enabled.
As the result, ncm object is released in ncm unbind
but 'dev->port_usb' associated to 'ncm->port' is not NULL.
And when ncm bind again to recover netdev, ncm object is reallocated
but usb0 interface is already associated to previous released ncm object.
Therefore, once usb0 interface is up and eth_start_xmit() is called,
released ncm object is dereferrenced and it might cause use-after-free memory.
[function unlink via configfs]
usb0: eth_stop dev->port_usb=ffffff9b179c3200
--> error happens in usb_ep_enable().
NCM: ncm_disable: ncm=ffffff9b179c3200
--> no gether_disconnect() since ncm->port.in_ep->enabled is false.
NCM: ncm_unbind: ncm unbind ncm=ffffff9b179c3200
NCM: ncm_free: ncm free ncm=ffffff9b179c3200 <-- released ncm
[function link via configfs]
NCM: ncm_alloc: ncm alloc ncm=ffffff9ac4f8a000
NCM: ncm_bind: ncm bind ncm=ffffff9ac4f8a000
NCM: ncm_set_alt: ncm=ffffff9ac4f8a000 alt=0
usb0: eth_open dev->port_usb=ffffff9b179c3200 <-- previous released ncm
usb0: eth_start dev->port_usb=ffffff9b179c3200 <--
eth_start_xmit()
--> dev->wrap()
Unable to handle kernel paging request at virtual address dead00000000014f
This patch addresses the issue by checking if 'ncm->netdev' is not NULL at
ncm_disable() to call gether_disconnect() to deassociate 'dev->port_usb'.
It's more reasonable to check 'ncm->netdev' to call gether_connect/disconnect
rather than check 'ncm->port.in_ep->enabled' since it might not be enabled
but the gether connection might be established.
Signed-off-by: Norihiko Hama <Norihiko.Hama@alpsalpine.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20240327023550.51214-1-Norihiko.Hama@alpsalpine.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d920a2ed86 upstream.
SanDisks USB3 storage may disapper after system reboot:
usb usb2-port3: link state change
xhci_hcd 0000:00:14.0: clear port3 link state change, portsc: 0x2c0
usb usb2-port3: do warm reset, port only
xhci_hcd 0000:00:14.0: xhci_hub_status_data: stopping usb2 port polling
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2b0, return 0x2b0
usb usb2-port3: not warm reset yet, waiting 50ms
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2f0, return 0x2f0
usb usb2-port3: not warm reset yet, waiting 200ms
...
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x6802c0, return 0x7002c0
usb usb2-port3: not warm reset yet, waiting 200ms
xhci_hcd 0000:00:14.0: clear port3 reset change, portsc: 0x4802c0
xhci_hcd 0000:00:14.0: clear port3 warm(BH) reset change, portsc: 0x4002c0
xhci_hcd 0000:00:14.0: clear port3 link state change, portsc: 0x2c0
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2c0, return 0x2c0
usb usb2-port3: not enabled, trying warm reset again...
This is due to the USB device still cause port change event after xHCI is
shuted down:
xhci_hcd 0000:38:00.0: // Setting command ring address to 0xffffe001
xhci_hcd 0000:38:00.0: xhci_resume: starting usb3 port polling.
xhci_hcd 0000:38:00.0: xhci_hub_status_data: stopping usb4 port polling
xhci_hcd 0000:38:00.0: xhci_hub_status_data: stopping usb3 port polling
xhci_hcd 0000:38:00.0: hcd_pci_runtime_resume: 0
xhci_hcd 0000:38:00.0: xhci_shutdown: stopping usb3 port polling.
xhci_hcd 0000:38:00.0: // Halt the HC
xhci_hcd 0000:38:00.0: xhci_shutdown completed - status = 1
xhci_hcd 0000:00:14.0: xhci_shutdown: stopping usb1 port polling.
xhci_hcd 0000:00:14.0: // Halt the HC
xhci_hcd 0000:00:14.0: xhci_shutdown completed - status = 1
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x1203, return 0x203
xhci_hcd 0000:00:14.0: set port reset, actual port 2-3 status = 0x1311
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x201203, return 0x100203
xhci_hcd 0000:00:14.0: clear port3 reset change, portsc: 0x1203
xhci_hcd 0000:00:14.0: clear port3 warm(BH) reset change, portsc: 0x1203
xhci_hcd 0000:00:14.0: clear port3 link state change, portsc: 0x1203
xhci_hcd 0000:00:14.0: clear port3 connect change, portsc: 0x1203
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x1203, return 0x203
usb 2-3: device not accepting address 2, error -108
xhci_hcd 0000:00:14.0: xHCI dying or halted, can't queue_command
xhci_hcd 0000:00:14.0: Set port 2-3 link state, portsc: 0x1203, write 0x11261
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x1263, return 0x263
xhci_hcd 0000:00:14.0: set port reset, actual port 2-3 status = 0x1271
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x12b1, return 0x2b1
usb usb2-port3: not reset yet, waiting 60ms
ACPI: PM: Preparing to enter system sleep state S5
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x12f1, return 0x2f1
usb usb2-port3: not reset yet, waiting 200ms
reboot: Restarting system
The port change event is caused by LPM transition, so disabling LPM at shutdown
to make sure the device is in U0 for warmboot.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20240305065140.66801-1-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1aa4ad4eb6 upstream.
We are seeing start_tx being called after port shutdown as noted by Jiri.
This happens because we are missing the startup and shutdown related
functions for the serial base port.
Let's fix the issue by adding startup and shutdown functions for the
serial base port to block tx flushing for the serial base port when the
port is not in use.
Fixes: 84a9582fd2 ("serial: core: Start managing serial controllers to enable runtime PM")
Cc: stable <stable@kernel.org>
Reported-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20240411055848.38190-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9cf7ea2eeb upstream.
The circular buffer is NULLified in uart_tty_port_shutdown()
under the spin lock. However, the PM or other timer based callbacks
may still trigger after this event without knowning that buffer pointer
is not valid. Since the serial code is a bit inconsistent in checking
the buffer state (some rely on the head-tail positions, some on the
buffer pointer), it's better to have both aligned, i.e. buffer pointer
to be NULL and head-tail possitions to be the same, meaning it's empty.
This will prevent asynchronous calls to dereference NULL pointer as
reported recently in 8250 case:
BUG: kernel NULL pointer dereference, address: 00000cf5
Workqueue: pm pm_runtime_work
EIP: serial8250_tx_chars (drivers/tty/serial/8250/8250_port.c:1809)
...
? serial8250_tx_chars (drivers/tty/serial/8250/8250_port.c:1809)
__start_tx (drivers/tty/serial/8250/8250_port.c:1551)
serial8250_start_tx (drivers/tty/serial/8250/8250_port.c:1654)
serial_port_runtime_suspend (include/linux/serial_core.h:667 drivers/tty/serial/serial_port.c:63)
__rpm_callback (drivers/base/power/runtime.c:393)
? serial_port_remove (drivers/tty/serial/serial_port.c:50)
rpm_suspend (drivers/base/power/runtime.c:447)
The proposed change will prevent ->start_tx() to be called during
suspend on shut down port.
Fixes: 43066e3222 ("serial: port: Don't suspend if the port is still busy")
Cc: stable <stable@kernel.org>
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202404031607.2e92eebe-lkp@intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240404150034.41648-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54c4ec5f8c upstream.
The uart_handle_cts_change() function in serial_core expects the caller
to hold uport->lock. For example, I have seen the below kernel splat,
when the Bluetooth driver is loaded on an i.MX28 board.
[ 85.119255] ------------[ cut here ]------------
[ 85.124413] WARNING: CPU: 0 PID: 27 at /drivers/tty/serial/serial_core.c:3453 uart_handle_cts_change+0xb4/0xec
[ 85.134694] Modules linked in: hci_uart bluetooth ecdh_generic ecc wlcore_sdio configfs
[ 85.143314] CPU: 0 PID: 27 Comm: kworker/u3:0 Not tainted 6.6.3-00021-gd62a2f068f92 #1
[ 85.151396] Hardware name: Freescale MXS (Device Tree)
[ 85.156679] Workqueue: hci0 hci_power_on [bluetooth]
(...)
[ 85.191765] uart_handle_cts_change from mxs_auart_irq_handle+0x380/0x3f4
[ 85.198787] mxs_auart_irq_handle from __handle_irq_event_percpu+0x88/0x210
(...)
Cc: stable@vger.kernel.org
Fixes: 4d90bb147e ("serial: core: Document and assert lock requirements for irq helpers")
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Emil Kronborg <emil.kronborg@protonmail.com>
Link: https://lore.kernel.org/r/20240320121530.11348-1-emil.kronborg@protonmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d1718530e3 upstream.
While vmk80xx does have endpoint checking implemented, some things
can fall through the cracks. Depending on the hardware model,
URBs can have either bulk or interrupt type, and current version
of vmk80xx_find_usb_endpoints() function does not take that fully
into account. While this warning does not seem to be too harmful,
at the very least it will crash systems with 'panic_on_warn' set on
them.
Fix the issue found by Syzkaller [1] by somewhat simplifying the
endpoint checking process with usb_find_common_endpoints() and
ensuring that only expected endpoint types are present.
This patch has not been tested on real hardware.
[1] Syzkaller report:
usb 1-1: BOGUS urb xfer, pipe 1 != type 3
WARNING: CPU: 0 PID: 781 at drivers/usb/core/urb.c:504 usb_submit_urb+0xc4e/0x18c0 drivers/usb/core/urb.c:503
...
Call Trace:
<TASK>
usb_start_wait_urb+0x113/0x520 drivers/usb/core/message.c:59
vmk80xx_reset_device drivers/comedi/drivers/vmk80xx.c:227 [inline]
vmk80xx_auto_attach+0xa1c/0x1a40 drivers/comedi/drivers/vmk80xx.c:818
comedi_auto_config+0x238/0x380 drivers/comedi/drivers.c:1067
usb_probe_interface+0x5cd/0xb00 drivers/usb/core/driver.c:399
...
Similar issue also found by Syzkaller:
Link: https://syzkaller.appspot.com/bug?extid=5205eb2f17de3e01946e
Reported-and-tested-by: syzbot+5f29dc6a889fc42bd896@syzkaller.appspotmail.com
Cc: stable <stable@kernel.org>
Fixes: 49253d542c ("staging: comedi: vmk80xx: factor out usb endpoint detection")
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Link: https://lore.kernel.org/r/20240408171633.31649-1-n.zhandarovich@fintech.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c38fa07dc6 upstream.
Currently we don't configure correctly the wake events after unplug of device
router. What can happen is that the downstream ports of host router will be
configured to wake on: USB4-wake and wake-on-disconnect, but not on
wake-on-connect. This may cause the later plugged device not to wake the
domain and fail in enumeration. Fix this by clearing downstream port's "USB4
Port is Configured" bit, after unplug of a device router.
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dcd12acaf3 upstream.
Currently we notify PM core about occurred wakes after any resume. This
is not actually needed after resume from runtime suspend. Hence, notify
PM core about occurred wakes only after resume from system sleep. Also,
if the wake occurred in USB4 router upstream port, we don't notify the
PM core about it since it is not actually needed and can cause
unexpected autowake (e.g. if /sys/power/wakeup_count is used).
While there add the missing kernel-doc for tb_switch_resume().
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aaef73821a upstream.
Commit 6d98eb95b4 ("binder: avoid potential data leakage when copying
txn") introduced changes to how binder objects are copied. In doing so,
it unintentionally removed an offset alignment check done through calls
to binder_alloc_copy_from_buffer() -> check_buffer().
These calls were replaced in binder_get_object() with copy_from_user(),
so now an explicit offset alignment check is needed here. This avoids
later complications when unwinding the objects gets harder.
It is worth noting this check existed prior to commit 7a67a39320
("binder: add function to copy binder object from buffer"), likely
removed due to redundancy at the time.
Fixes: 6d98eb95b4 ("binder: avoid potential data leakage when copying txn")
Cc: stable@vger.kernel.org
Signed-off-by: Carlos Llamas <cmllamas@google.com>
Acked-by: Todd Kjos <tkjos@google.com>
Link: https://lore.kernel.org/r/20240330190115.1877819-1-cmllamas@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0553e753ea ]
Next patch will move devlink register to be first. Therefore, whenever
mlx5 will register a param, the user will be notified.
In order to notify the user, devlink is using the get() callback of
the param. Hence, resources that are being used by the get() callback
must be set before the devlink param is registered.
Therefore, store eswitch pointer inside mdev before registering the
param.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240409190820.227554-2-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9543f6e266 ]
Fix cpuid_deps[] to list the correct dependencies for GFNI, VAES, and
VPCLMULQDQ. These features don't depend on AVX512, and there exist CPUs
that support these features but not AVX512. GFNI actually doesn't even
depend on AVX.
This prevents GFNI from being unnecessarily disabled if AVX is disabled
to mitigate the GDS vulnerability.
This also prevents all three features from being unnecessarily disabled
if AVX512VL (or its dependency AVX512F) were to be disabled, but it
looks like there isn't any case where this happens anyway.
Fixes: c128dbfa0f ("x86/cpufeatures: Enable new SSE/AVX/AVX512 CPU features")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lore.kernel.org/r/20240417060434.47101-1-ebiggers@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f7b1d8b55 ]
mt8183-mfgcfg has a mutual dependency with genpd during the probing
stage, which leads to a deadlock in the following call stack:
CPU0: genpd_lock --> clk_prepare_lock
genpd_power_off_work_fn()
genpd_lock()
generic_pm_domain::power_off()
clk_unprepare()
clk_prepare_lock()
CPU1: clk_prepare_lock --> genpd_lock
clk_register()
__clk_core_init()
clk_prepare_lock()
clk_pm_runtime_get()
genpd_lock()
Do a runtime PM get at the probe function to make sure clk_register()
won't acquire the genpd lock. Instead of only modifying mt8183-mfgcfg,
do this on all mediatek clock controller probings because we don't
believe this would cause any regression.
Verified on MT8183 and MT8192 Chromebooks.
Fixes: acddfc2c26 ("clk: mediatek: Add MT8183 clock support")
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Link: https://lore.kernel.org/r/20240312115249.3341654-1-treapking@chromium.org
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d1e795f75 ]
Similar to the previous commit, we should make sure that all devices are
runtime resumed before printing the clk_summary through debugfs. Failure
to do so would result in a deadlock if the thread is resuming a device
to print clk state and that device is also runtime resuming in another
thread, e.g the screen is turning on and the display driver is starting
up. We remove the calls to clk_pm_runtime_{get,put}() in this path
because they're superfluous now that we know the devices are runtime
resumed. This also squashes a bug where the return value of
clk_pm_runtime_get() wasn't checked, leading to an RPM count underflow
on error paths.
Fixes: 1bb294a798 ("clk: Enable/Disable runtime PM for clk_summary")
Cc: Taniya Das <quic_tdas@quicinc.com>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20240325184204.745706-6-sboyd@kernel.org
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e581cf5d21 ]
Doug reported [1] the following hung task:
INFO: task swapper/0:1 blocked for more than 122 seconds.
Not tainted 5.15.149-21875-gf795ebc40eb8 #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:swapper/0 state:D stack: 0 pid: 1 ppid: 0 flags:0x00000008
Call trace:
__switch_to+0xf4/0x1f4
__schedule+0x418/0xb80
schedule+0x5c/0x10c
rpm_resume+0xe0/0x52c
rpm_resume+0x178/0x52c
__pm_runtime_resume+0x58/0x98
clk_pm_runtime_get+0x30/0xb0
clk_disable_unused_subtree+0x58/0x208
clk_disable_unused_subtree+0x38/0x208
clk_disable_unused_subtree+0x38/0x208
clk_disable_unused_subtree+0x38/0x208
clk_disable_unused_subtree+0x38/0x208
clk_disable_unused+0x4c/0xe4
do_one_initcall+0xcc/0x2d8
do_initcall_level+0xa4/0x148
do_initcalls+0x5c/0x9c
do_basic_setup+0x24/0x30
kernel_init_freeable+0xec/0x164
kernel_init+0x28/0x120
ret_from_fork+0x10/0x20
INFO: task kworker/u16:0:9 blocked for more than 122 seconds.
Not tainted 5.15.149-21875-gf795ebc40eb8 #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:kworker/u16:0 state:D stack: 0 pid: 9 ppid: 2 flags:0x00000008
Workqueue: events_unbound deferred_probe_work_func
Call trace:
__switch_to+0xf4/0x1f4
__schedule+0x418/0xb80
schedule+0x5c/0x10c
schedule_preempt_disabled+0x2c/0x48
__mutex_lock+0x238/0x488
__mutex_lock_slowpath+0x1c/0x28
mutex_lock+0x50/0x74
clk_prepare_lock+0x7c/0x9c
clk_core_prepare_lock+0x20/0x44
clk_prepare+0x24/0x30
clk_bulk_prepare+0x40/0xb0
mdss_runtime_resume+0x54/0x1c8
pm_generic_runtime_resume+0x30/0x44
__genpd_runtime_resume+0x68/0x7c
genpd_runtime_resume+0x108/0x1f4
__rpm_callback+0x84/0x144
rpm_callback+0x30/0x88
rpm_resume+0x1f4/0x52c
rpm_resume+0x178/0x52c
__pm_runtime_resume+0x58/0x98
__device_attach+0xe0/0x170
device_initial_probe+0x1c/0x28
bus_probe_device+0x3c/0x9c
device_add+0x644/0x814
mipi_dsi_device_register_full+0xe4/0x170
devm_mipi_dsi_device_register_full+0x28/0x70
ti_sn_bridge_probe+0x1dc/0x2c0
auxiliary_bus_probe+0x4c/0x94
really_probe+0xcc/0x2c8
__driver_probe_device+0xa8/0x130
driver_probe_device+0x48/0x110
__device_attach_driver+0xa4/0xcc
bus_for_each_drv+0x8c/0xd8
__device_attach+0xf8/0x170
device_initial_probe+0x1c/0x28
bus_probe_device+0x3c/0x9c
deferred_probe_work_func+0x9c/0xd8
process_one_work+0x148/0x518
worker_thread+0x138/0x350
kthread+0x138/0x1e0
ret_from_fork+0x10/0x20
The first thread is walking the clk tree and calling
clk_pm_runtime_get() to power on devices required to read the clk
hardware via struct clk_ops::is_enabled(). This thread holds the clk
prepare_lock, and is trying to runtime PM resume a device, when it finds
that the device is in the process of resuming so the thread schedule()s
away waiting for the device to finish resuming before continuing. The
second thread is runtime PM resuming the same device, but the runtime
resume callback is calling clk_prepare(), trying to grab the
prepare_lock waiting on the first thread.
This is a classic ABBA deadlock. To properly fix the deadlock, we must
never runtime PM resume or suspend a device with the clk prepare_lock
held. Actually doing that is near impossible today because the global
prepare_lock would have to be dropped in the middle of the tree, the
device runtime PM resumed/suspended, and then the prepare_lock grabbed
again to ensure consistency of the clk tree topology. If anything
changes with the clk tree in the meantime, we've lost and will need to
start the operation all over again.
Luckily, most of the time we're simply incrementing or decrementing the
runtime PM count on an active device, so we don't have the chance to
schedule away with the prepare_lock held. Let's fix this immediate
problem that can be triggered more easily by simply booting on Qualcomm
sc7180.
Introduce a list of clk_core structures that have been registered, or
are in the process of being registered, that require runtime PM to
operate. Iterate this list and call clk_pm_runtime_get() on each of them
without holding the prepare_lock during clk_disable_unused(). This way
we can be certain that the runtime PM state of the devices will be
active and resumed so we can't schedule away while walking the clk tree
with the prepare_lock held. Similarly, call clk_pm_runtime_put() without
the prepare_lock held to properly drop the runtime PM reference. We
remove the calls to clk_pm_runtime_{get,put}() in this path because
they're superfluous now that we know the devices are runtime resumed.
Reported-by: Douglas Anderson <dianders@chromium.org>
Closes: https://lore.kernel.org/all/20220922084322.RFC.2.I375b6b9e0a0a5348962f004beb3dafee6a12dfbb@changeid/ [1]
Closes: https://issuetracker.google.com/328070191
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Fixes: 9a34b45397 ("clk: Add support for runtime PM")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20240325184204.745706-5-sboyd@kernel.org
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d05ae531c ]
Initialize this kref once we allocate memory for the struct clk_core so
that we can reuse the release function to free any memory associated
with the structure. This mostly consolidates code, but also clarifies
that the kref lifetime exists once the container structure (struct
clk_core) is allocated instead of leaving it in a half-baked state for
most of __clk_core_init().
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20240325184204.745706-4-sboyd@kernel.org
Stable-dep-of: e581cf5d21 ("clk: Get runtime PM before walking tree during disable_unused")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8358a76cfb ]
Removing this assertion lets us move the kref_put() call outside the
prepare_lock section. We don't need to hold the prepare_lock here to
free memory and destroy the clk_core structure. We've already unlinked
the clk from the clk tree and by the time the release function runs
nothing holds a reference to the clk_core anymore so anything with the
pointer can't access the memory that's being freed anyway. Way back in
commit 496eadf821 ("clk: Use lockdep asserts to find missing hold of
prepare_lock") we didn't need to have this assertion either.
Fixes: 496eadf821 ("clk: Use lockdep asserts to find missing hold of prepare_lock")
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20240325184204.745706-2-sboyd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de1bf25b6d ]
The icc_lock mutex was split into separate icc_lock and icc_bw_lock
mutexes in [1] to avoid lockdep splats. However, this didn't adequately
protect access to icc_node::req_list.
The icc_set_bw() function will eventually iterate over req_list while
only holding icc_bw_lock, but req_list can be modified while only
holding icc_lock. This causes races between icc_set_bw(), of_icc_get(),
and icc_put().
Example A:
CPU0 CPU1
---- ----
icc_set_bw(path_a)
mutex_lock(&icc_bw_lock);
icc_put(path_b)
mutex_lock(&icc_lock);
aggregate_requests()
hlist_for_each_entry(r, ...
hlist_del(...
<r = invalid pointer>
Example B:
CPU0 CPU1
---- ----
icc_set_bw(path_a)
mutex_lock(&icc_bw_lock);
path_b = of_icc_get()
of_icc_get_by_index()
mutex_lock(&icc_lock);
path_find()
path_init()
aggregate_requests()
hlist_for_each_entry(r, ...
hlist_add_head(...
<r = invalid pointer>
Fix this by ensuring icc_bw_lock is always held before manipulating
icc_node::req_list. The additional places icc_bw_lock is held don't
perform any memory allocations, so we should still be safe from the
original lockdep splats that motivated the separate locks.
[1] commit af42269c35 ("interconnect: Fix locking for runpm vs reclaim")
Signed-off-by: Mike Tipton <quic_mdtipton@quicinc.com>
Fixes: af42269c35 ("interconnect: Fix locking for runpm vs reclaim")
Reviewed-by: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20240305225652.22872-1-quic_mdtipton@quicinc.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a1ccf0c72 ]
This patch introduces a new USB quirk,
USB_QUIRK_SHORT_SET_ADDRESS_REQ_TIMEOUT, which modifies the timeout value
for the SET_ADDRESS request. The standard timeout for USB request/command
is 5000 ms, as recommended in the USB 3.2 specification (section 9.2.6.1).
However, certain scenarios, such as connecting devices through an APTIV
hub, can lead to timeout errors when the device enumerates as full speed
initially and later switches to high speed during chirp negotiation.
In such cases, USB analyzer logs reveal that the bus suspends for
5 seconds due to incorrect chirp parsing and resumes only after two
consecutive timeout errors trigger a hub driver reset.
Packet(54) Dir(?) Full Speed J(997.100 us) Idle( 2.850 us)
_______| Time Stamp(28 . 105 910 682)
_______|_____________________________________________________________Ch0
Packet(55) Dir(?) Full Speed J(997.118 us) Idle( 2.850 us)
_______| Time Stamp(28 . 106 910 632)
_______|_____________________________________________________________Ch0
Packet(56) Dir(?) Full Speed J(399.650 us) Idle(222.582 us)
_______| Time Stamp(28 . 107 910 600)
_______|_____________________________________________________________Ch0
Packet(57) Dir Chirp J( 23.955 ms) Idle(115.169 ms)
_______| Time Stamp(28 . 108 532 832)
_______|_____________________________________________________________Ch0
Packet(58) Dir(?) Full Speed J (Suspend)( 5.347 sec) Idle( 5.366 us)
_______| Time Stamp(28 . 247 657 600)
_______|_____________________________________________________________Ch0
This 5-second delay in device enumeration is undesirable, particularly
in automotive applications where quick enumeration is crucial
(ideally within 3 seconds).
The newly introduced quirks provide the flexibility to align with a
3-second time limit, as required in specific contexts like automotive
applications.
By reducing the SET_ADDRESS request timeout to 500 ms, the
system can respond more swiftly to errors, initiate rapid recovery, and
ensure efficient device enumeration. This change is vital for scenarios
where rapid smartphone enumeration and screen projection are essential.
To use the quirk, please write "vendor_id:product_id:p" to
/sys/bus/usb/drivers/hub/module/parameter/quirks
For example,
echo "0x2c48:0x0132:p" > /sys/bus/usb/drivers/hub/module/parameters/quirks"
Signed-off-by: Hardik Gajjar <hgajjar@de.adit-jv.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20231027152029.104363-2-hgajjar@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a769154c7c ]
- The HCD address_device callback now accepts a user-defined timeout value
in milliseconds, providing better control over command execution times.
- The default timeout value for the address_device command has been set
to 5000 ms, aligning with the USB 3.2 specification. However, this
timeout can be adjusted as needed.
- The xhci_setup_device function has been updated to accept the timeout
value, allowing it to specify the maximum wait time for the command
operation to complete.
- The hub driver has also been updated to accommodate the newly added
timeout parameter during the SET_ADDRESS request.
Signed-off-by: Hardik Gajjar <hgajjar@de.adit-jv.com>
Reviewed-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231027152029.104363-1-hgajjar@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 5a1ccf0c72 ("usb: new quirk to reduce the SET_ADDRESS request timeout")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit efc3d7d203 ]
This driver was originally developed for the Focusrite Scarlett Gen 2
series. Since then Focusrite have used a similar protocol for their
Gen 3, Gen 4, Clarett USB, Clarett+, and Vocaster series.
Let's call this common protocol the "Scarlett 2 Protocol" and rename
the driver to scarlett2 to not imply that it is restricted to Gen 2
series devices.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/e1ad7f69a1e20cdb39094164504389160c1a0a0b.1698342632.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2b17b489e4 ]
It has been confirmed that all devices in the Focusrite Clarett USB
series work the same as the devices in the Clarett+ series. Add the
missing PIDs to enable support for the Clarett 2Pre and 4Pre USB.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/ZSFB8EVTG1PK1eq/@m.b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b61a3acada ]
The Focusrite Clarett+ series uses the same protocol as the Scarlett
Gen 2 and Gen 3 series. This patch adds support for the Clarett+ 2Pre
and Clarett+ 4Pre similarly to the existing 8Pre support by adding
appropriate entries to the scarlett2 driver.
The Clarett 2Pre USB and 4Pre USB presumably use the same protocol as
well, so support for them can easily be added if someone can test.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/ZRL7qjC3tYQllT3H@m.b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e743781d6 ]
This driver was originally developed for the Focusrite Scarlett Gen 2
series, but now also supports the Scarlett Gen 3 series, the
Clarett 8Pre USB, and the Clarett+ 8Pre. The messages output by the
driver on initialisation and error include the identifying text
"Scarlett Gen 2/3", but this is no longer accurate, and writing
"Scarlett Gen 2/3/Clarett USB/Clarett+" would be unwieldy.
Add series_name field to the scarlett2_device_entry struct so that
concise and accurate messages can be output.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/3774b9d35bf1fbdd6fdad9f3f4f97e9b82ac76bf.1694705811.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Stable-dep-of: b61a3acada ("ALSA: scarlett2: Add Focusrite Clarett+ 2Pre and 4Pre support")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc83058f59 ]
Early versions of this mixer driver did not work on all hardware, so
out of caution the driver was disabled by default and had to be
explicitly enabled with device_setup=1.
Since commit 764fa6e686 ("ALSA: usb-audio: scarlett2: Fix device
hang with ehci-pci") no more problems of this nature have been
reported. Therefore, enable the driver by default but provide a new
device_setup option to disable the driver in case that is needed.
- device_setup value of 0 now means "enable" rather than "disable".
- device_setup value of 1 is now ignored.
- device_setup value of 4 now means "disable".
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/89600a35b40307f2766578ad1ca2f21801286b58.1694705811.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Stable-dep-of: b61a3acada ("ALSA: scarlett2: Add Focusrite Clarett+ 2Pre and 4Pre support")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 59a54c5f3d upstream.
Boot firmware (typically BIOS) might have created tunnels of its own.
The tunnel configuration that it does might be sub-optimal. For instance
it may only support HBR2 monitors so the DisplayPort tunnels it created
may limit Linux graphics drivers. In addition there is an issue on some
AMD based systems where the BIOS does not allocate enough PCIe resources
for future topology extension. By resetting the USB4 topology the PCIe
links will be reset as well allowing Linux to re-allocate.
This aligns the behavior with Windows Connection Manager.
We already issued host router reset for USB4 v2 routers, now extend it
to USB4 v1 routers as well. For pre-USB4 (that's Apple systems) we leave
it as is and continue to discover the existing tunnels.
Suggested-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Sanath S <Sanath.S@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 319e6ac143 ]
The Pandora uses GPIO descriptors pretty much exclusively, but not
for ASoC, so let's fix it. Register the pins in a descriptor table
in the machine since the ASoC device is not using device tree.
Use static locals for the GPIO descriptors because I'm not able
to experient with better state storage on any real hardware. Others
using the Pandora can come afterwards and improve this.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Link: https://lore.kernel.org/r/20230926-descriptors-asoc-ti-v1-4-60cf4f8adbc5@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf92bb778e ]
When Output Resource (dcb->or) value is assigned in
fabricate_dcb_output(), there may be out of bounds access to
dac_users array in case dcb->or is zero because ffs(dcb->or) is
used as index there.
The 'or' argument of fabricate_dcb_output() must be interpreted as a
number of bit to set, not value.
Utilize macros from 'enum nouveau_or' in calls instead of hardcoding.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 2e5702aff3 ("drm/nouveau: fabricate DCB encoder table for iMac G4")
Fixes: 670820c0e6 ("drm/nouveau: Workaround incorrect DCB entry on a GeForce3 Ti 200.")
Signed-off-by: Mikhail Kobuk <m.kobuk@ispras.ru>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240411110854.16701-1-m.kobuk@ispras.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d8527f2f9 ]
A race condition exists in ccw_device_set_online() that can cause the
online process to fail, leaving the affected device in an inconsistent
state. As a result, subsequent attempts to set that device online fail
with return code ENODEV.
The problem occurs when a path verification request arrives after
a wait for final device state completed, but before the result state
is evaluated.
Fix this by ensuring that the CCW-device lock is held between
determining final state and checking result state.
Note that since:
commit 2297791c92 ("s390/cio: dont unregister subchannel from child-drivers")
path verification requests are much more likely to occur during boot,
resulting in an increased chance of this race condition occurring.
Fixes: 2297791c92 ("s390/cio: dont unregister subchannel from child-drivers")
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Vineeth Vijayan <vneethv@linux.ibm.com>
Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 607638faf2 ]
A deferred condition code 1 response indicates that I/O was not started
and should be retried. The current QDIO implementation handles a cc1
response as I/O error, resulting in a failed QDIO setup. This can happen
for example when a path verification request arrives at the same time
as QDIO setup I/O is started.
Fix this by retrying the QDIO setup I/O when a cc1 response is received.
Note that since
commit 2297791c92 ("s390/cio: dont unregister subchannel from child-drivers")
commit 5ef1dc40ff ("s390/cio: fix invalid -EBUSY on ccw_device_start")
deferred cc1 responses are much more likely to occur. See the commit
message of the latter for more background information.
Fixes: 2297791c92 ("s390/cio: dont unregister subchannel from child-drivers")
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c24cd679b0 ]
The TX and RX DMA Channels used by the driver to exchange data with CPSW
are not guaranteed to be in a clean state during driver initialization.
The Bootloader could have used the same DMA Channels without cleaning them
up in the event of failure. Thus, reset and disable the DMA Channels to
ensure that they are in a clean state before using them.
Fixes: 93a7653031 ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Reported-by: Schuyler Patton <spatton@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240417095425.2253876-1-s-vadapalli@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 94667949ec ]
The WLAN + WED reset sequence relies on being able to receive interrupts from
the card, in order to synchronize individual steps with the firmware.
When WED is stopped, leave interrupts running and rely on the driver turning
off unwanted ones.
WED DMA also needs to be disabled before resetting.
Fixes: f78cd9c783 ("net: ethernet: mtk_wed: update mtk_wed_stop")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20240416082330.82564-1-nbd@nbd.name
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69ffed4b62 ]
The flags in the software node properties are supposed to be
the GPIO lookup flags, which are provided by gpio/machine.h,
as the software nodes are the kernel internal thing and doesn't
need to rely to any of ABIs.
Fixes: e7f9ff5dc9 ("gpiolib: add support for software nodes")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 83781384a9 ]
Since [1], dma_alloc_coherent() does not accept requests for GFP_COMP
anymore, even on archs that may be able to fulfill this. Functionality that
relied on the receive buffer being a compound page broke at that point:
The SMC-D protocol, that utilizes the ism device driver, passes receive
buffers to the splice processor in a struct splice_pipe_desc with a
single entry list of struct pages. As the buffer is no longer a compound
page, the splice processor now rejects requests to handle more than a
page worth of data.
Replace dma_alloc_coherent() and allocate a buffer with folio_alloc and
create a DMA map for it with dma_map_page(). Since only receive buffers
on ISM devices use DMA, qualify the mapping as FROM_DEVICE.
Since ISM devices are available on arch s390, only, and on that arch all
DMA is coherent, there is no need to introduce and export some kind of
dma_sync_to_cpu() method to be called by the SMC-D protocol layer.
Analogously, replace dma_free_coherent by a two step dma_unmap_page,
then folio_put to free the receive buffer.
[1] https://lore.kernel.org/all/20221113163535.884299-1-hch@lst.de/
Fixes: c08004eede ("s390/ism: don't pass bogus GFP_ flags to dma_alloc_coherent")
Signed-off-by: Gerd Bayer <gbayer@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c606d1385 ]
The "MT7988A Wi-Fi 7 Generation Router Platform: Datasheet (Open Version)
v0.1" document shows bits 16 to 18 as the MIRROR_PORT field of the CPU
forward control register. Currently, the MT7530 DSA subdriver configures
bits 0 to 2 of the CPU forward control register which breaks the port
mirroring feature for the MT7988 SoC switch.
Fix this by using the MT7531_MIRROR_PORT_GET() and MT7531_MIRROR_PORT_SET()
macros which utilise the correct bits.
Fixes: 110c18bfed ("net: dsa: mt7530: introduce driver for MT7988 built-in switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d59cf049c8 ]
This switch intellectual property provides a bit on the ARL global control
register which controls allowing mirroring frames which are received on the
local port (monitor port). This bit is unset after reset.
This ability must be enabled to fully support the port mirroring feature on
this switch intellectual property.
Therefore, this patch fixes the traffic not being reflected on a port,
which would be configured like below:
tc qdisc add dev swp0 clsact
tc filter add dev swp0 ingress matchall skip_sw \
action mirred egress mirror dev swp0
As a side note, this configuration provides the hairpinning feature for a
single port.
Fixes: 37feab6076 ("net: dsa: mt7530: add support for port mirroring")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f8bbc07ac5 ]
vhost_worker will call tun call backs to receive packets. If too many
illegal packets arrives, tun_do_read will keep dumping packet contents.
When console is enabled, it will costs much more cpu time to dump
packet and soft lockup will be detected.
net_ratelimit mechanism can be used to limit the dumping rate.
PID: 33036 TASK: ffff949da6f20000 CPU: 23 COMMAND: "vhost-32980"
#0 [fffffe00003fce50] crash_nmi_callback at ffffffff89249253
#1 [fffffe00003fce58] nmi_handle at ffffffff89225fa3
#2 [fffffe00003fceb0] default_do_nmi at ffffffff8922642e
#3 [fffffe00003fced0] do_nmi at ffffffff8922660d
#4 [fffffe00003fcef0] end_repeat_nmi at ffffffff89c01663
[exception RIP: io_serial_in+20]
RIP: ffffffff89792594 RSP: ffffa655314979e8 RFLAGS: 00000002
RAX: ffffffff89792500 RBX: ffffffff8af428a0 RCX: 0000000000000000
RDX: 00000000000003fd RSI: 0000000000000005 RDI: ffffffff8af428a0
RBP: 0000000000002710 R8: 0000000000000004 R9: 000000000000000f
R10: 0000000000000000 R11: ffffffff8acbf64f R12: 0000000000000020
R13: ffffffff8acbf698 R14: 0000000000000058 R15: 0000000000000000
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
#5 [ffffa655314979e8] io_serial_in at ffffffff89792594
#6 [ffffa655314979e8] wait_for_xmitr at ffffffff89793470
#7 [ffffa65531497a08] serial8250_console_putchar at ffffffff897934f6
#8 [ffffa65531497a20] uart_console_write at ffffffff8978b605
#9 [ffffa65531497a48] serial8250_console_write at ffffffff89796558
#10 [ffffa65531497ac8] console_unlock at ffffffff89316124
#11 [ffffa65531497b10] vprintk_emit at ffffffff89317c07
#12 [ffffa65531497b68] printk at ffffffff89318306
#13 [ffffa65531497bc8] print_hex_dump at ffffffff89650765
#14 [ffffa65531497ca8] tun_do_read at ffffffffc0b06c27 [tun]
#15 [ffffa65531497d38] tun_recvmsg at ffffffffc0b06e34 [tun]
#16 [ffffa65531497d68] handle_rx at ffffffffc0c5d682 [vhost_net]
#17 [ffffa65531497ed0] vhost_worker at ffffffffc0c644dc [vhost]
#18 [ffffa65531497f10] kthread at ffffffff892d2e72
#19 [ffffa65531497f50] ret_from_fork at ffffffff89c0022f
Fixes: ef3db4a595 ("tun: avoid BUG, dump packet on GSO errors")
Signed-off-by: Lei Chen <lei.chen@smartx.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://lore.kernel.org/r/20240415020247.2207781-1-lei.chen@smartx.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2cca35f5dd ]
Add missing FLOW_DISSECTOR_KEY_ENC_* checks to TC flower filter parsing.
Without these checks, it would be possible to add filters with tunnel
options on non-tunnel devices. enc_* options are only valid for tunnel
devices.
Example:
devlink dev eswitch set $PF1_PCI mode switchdev
echo 1 > /sys/class/net/$PF1/device/sriov_numvfs
tc qdisc add dev $VF1_PR ingress
ethtool -K $PF1 hw-tc-offload on
tc filter add dev $VF1_PR ingress flower enc_ttl 12 skip_sw action drop
Fixes: 9e300987d4 ("ice: VXLAN and Geneve TC support")
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7327871572 ]
The check for flags is done to not pass empty lookups to adding switch
rule functions. Since metadata is always added to lookups there is no
need to check against the flag.
It is also fixing the problem with such rule:
$ tc filter add dev gtp_dev ingress protocol ip prio 0 flower \
enc_dst_port 2123 action drop
Switch block in case of GTP can't parse the destination port, because it
should always be set to GTP specific value. The same with ethertype. The
result is that there is no other matching criteria than GTP tunnel. In
this case flags is 0, rule can't be added only because of defensive
check against flags.
Fixes: 9a225f81f5 ("ice: Support GTP-U and GTP-C offload in switchdev")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 428051600c ]
In case of traffic going from the VF (so ingress for port representor)
source VSI should be consider during packet classification. It is
needed for hardware to not match packets from different ports with
filters added on other port.
It is only for "from VF" traffic, because other traffic direction
doesn't have source VSI.
Set correct ::src_vsi in rule_info to pass it to the hardware filter.
For example this rule should drop only ipv4 packets from eth10, not from
the others VF PRs. It is needed to check source VSI in this case.
$tc filter add dev eth10 ingress protocol ip flower skip_sw action drop
Fixes: 0d08a441fb ("ice: ndo_setup_tc implementation for PF")
Reviewed-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9cb54af214 ]
Here is the list of the MAC capabilities specific to the particular DW MAC
IP-cores currently supported by the driver:
DW MAC100: MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
MAC_10 | MAC_100
DW GMAC: MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
MAC_10 | MAC_100 | MAC_1000
Allwinner sun8i MAC: MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
MAC_10 | MAC_100 | MAC_1000
DW QoS Eth: MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
MAC_10 | MAC_100 | MAC_1000 | MAC_2500FD
if there is more than 1 active Tx/Rx queues:
MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
MAC_10FD | MAC_100FD | MAC_1000FD | MAC_2500FD
DW XGMAC: MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
MAC_1000FD | MAC_2500FD | MAC_5000FD | MAC_10000FD
DW XLGMAC: MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
MAC_1000FD | MAC_2500FD | MAC_5000FD | MAC_10000FD |
MAC_25000FD | MAC_40000FD | MAC_50000FD | MAC_100000FD
As you can see there are only two common capabilities:
MAC_ASYM_PAUSE | MAC_SYM_PAUSE.
Meanwhile what is currently implemented defines 10/100/1000 link speeds
for all IP-cores, which is definitely incorrect for DW MAC100, DW XGMAC
and DW XLGMAC devices.
Seeing the flow-control is implemented as a callback for each MAC IP-core
(see dwmac100_flow_ctrl(), dwmac1000_flow_ctrl(), sun8i_dwmac_flow_ctrl(),
etc) and since the MAC-specific setup() method is supposed to be called
for each available DW MAC-based device, the capabilities initialization
can be freely moved to these setup() functions, thus correctly setting up
the MAC-capabilities for each IP-core (including the Allwinner Sun8i). A
new stmmac_link::caps field was specifically introduced for that so to
have all link-specific info preserved in a single structure.
Note the suggested change fixes three earlier commits at a time. The
commit 5b0d7d7da6 ("net: stmmac: Add the missing speeds that XGMAC
supports") permitted the 10-100 link speeds and 1G half-duplex mode for DW
XGMAC IP-core even though it doesn't support them. The commit df7699c70c
("net: stmmac: Do not cut down 1G modes") incorrectly added the MAC1000
capability to the DW MAC100 IP-core. Similarly to the DW XGMAC the commit
8a880936e9 ("net: stmmac: Add XLGMII support") incorrectly permitted the
10-100 link speeds and 1G half-duplex mode for DW XLGMAC IP-core.
Fixes: 5b0d7d7da6 ("net: stmmac: Add the missing speeds that XGMAC supports")
Fixes: df7699c70c ("net: stmmac: Do not cut down 1G modes")
Fixes: 8a880936e9 ("net: stmmac: Add XLGMII support")
Suggested-by: Russell King (Oracle) <linux@armlinux.org.uk>
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Romain Gantois <romain.gantois@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59c3d6ca6c ]
It's possible to have the maximum link speed being artificially limited on
the platform-specific basis. It's done either by setting up the
plat_stmmacenet_data::max_speed field or by specifying the "max-speed"
DT-property. In such cases it's required that any specific
MAC-capabilities re-initializations would take the limit into account. In
particular the link speed capabilities may change during the number of
active Tx/Rx queues re-initialization. But the currently implemented
procedure doesn't take the speed limit into account.
Fix that by calling phylink_limit_mac_speed() in the
stmmac_reinit_queues() method if the speed limitation was required in the
same way as it's done in the stmmac_phy_setup() function.
Fixes: 95201f36f3 ("net: stmmac: update MAC capabilities when tx queues are updated")
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Romain Gantois <romain.gantois@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ebd96f5da ]
There are three DW MAC IP-cores which can have the multiple Tx/Rx queues
enabled:
DW GMAC v3.7+ with AV feature,
DW QoS Eth v4.x/v5.x,
DW XGMAC/XLGMAC
Based on the respective HW databooks, only the DW QoS Eth IP-core doesn't
support the half-duplex link mode in case if more than one queues enabled:
"In multiple queue/channel configurations, for half-duplex operation,
enable only the Q0/CH0 on Tx and Rx. For single queue/channel in
full-duplex operation, any queue/channel can be enabled."
The rest of the IP-cores don't have such constraint. Thus in order to have
the constraint applied for the DW QoS Eth MACs only, let's move the it'
implementation to the respective MAC-capabilities getter and make sure the
getter is called in the queues re-init procedure.
Fixes: b6cfffa7ad ("stmmac: fix DMA channel hang in half-duplex mode")
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Romain Gantois <romain.gantois@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 75ce9506ee ]
Upon reviewing the flower control flags handling in
this driver, I notice that the key wasn't being used,
only the mask.
Ie. `tc flower ... ip_flags nofrag` was hardware
offloaded as `... ip_flags frag`.
Only compile tested, no access to HW.
Fixes: c672e37279 ("octeontx2-pf: Add support to filter packet based on IP fragment")
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1382e3b6a3 ]
The commit fc8b2a6194
("net: more strict VIRTIO_NET_HDR_GSO_UDP_L4 validation")
adds check of potential number of UDP segments vs
UDP_MAX_SEGMENTS in linux/virtio_net.h.
After this change certification test of USO guest-to-guest
transmit on Windows driver for virtio-net device fails,
for example with packet size of ~64K and mss of 536 bytes.
In general the USO should not be more restrictive than TSO.
Indeed, in case of unreasonably small mss a lot of segments
can cause queue overflow and packet loss on the destination.
Limit of 128 segments is good for any practical purpose,
with minimal meaningful mss of 536 the maximal UDP packet will
be divided to ~120 segments.
The number of segments for UDP packets is validated vs
UDP_MAX_SEGMENTS also in udp.c (v4,v6), this does not affect
quest-to-guest path but does affect packets sent to host, for
example.
It is important to mention that UDP_MAX_SEGMENTS is kernel-only
define and not available to user mode socket applications.
In order to request MSS smaller than MTU the applications
just uses setsockopt with SOL_UDP and UDP_SEGMENT and there is
no limitations on socket API level.
Fixes: fc8b2a6194 ("net: more strict VIRTIO_NET_HDR_GSO_UDP_L4 validation")
Signed-off-by: Yuri Benditovich <yuri.benditovich@daynix.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fef965764c ]
When disabling aRFS under the `priv->state_lock`, any scheduled
aRFS works are canceled using the `cancel_work_sync` function,
which waits for the work to end if it has already started.
However, while waiting for the work handler, the handler will
try to acquire the `state_lock` which is already acquired.
The worker acquires the lock to delete the rules if the state
is down, which is not the worker's responsibility since
disabling aRFS deletes the rules.
Add an aRFS state variable, which indicates whether the aRFS is
enabled and prevent adding rules when the aRFS is disabled.
Kernel log:
======================================================
WARNING: possible circular locking dependency detected
6.7.0-rc4_net_next_mlx5_5483eb2 #1 Tainted: G I
------------------------------------------------------
ethtool/386089 is trying to acquire lock:
ffff88810f21ce68 ((work_completion)(&rule->arfs_work)){+.+.}-{0:0}, at: __flush_work+0x74/0x4e0
but task is already holding lock:
ffff8884a1808cc0 (&priv->state_lock){+.+.}-{3:3}, at: mlx5e_ethtool_set_channels+0x53/0x200 [mlx5_core]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&priv->state_lock){+.+.}-{3:3}:
__mutex_lock+0x80/0xc90
arfs_handle_work+0x4b/0x3b0 [mlx5_core]
process_one_work+0x1dc/0x4a0
worker_thread+0x1bf/0x3c0
kthread+0xd7/0x100
ret_from_fork+0x2d/0x50
ret_from_fork_asm+0x11/0x20
-> #0 ((work_completion)(&rule->arfs_work)){+.+.}-{0:0}:
__lock_acquire+0x17b4/0x2c80
lock_acquire+0xd0/0x2b0
__flush_work+0x7a/0x4e0
__cancel_work_timer+0x131/0x1c0
arfs_del_rules+0x143/0x1e0 [mlx5_core]
mlx5e_arfs_disable+0x1b/0x30 [mlx5_core]
mlx5e_ethtool_set_channels+0xcb/0x200 [mlx5_core]
ethnl_set_channels+0x28f/0x3b0
ethnl_default_set_doit+0xec/0x240
genl_family_rcv_msg_doit+0xd0/0x120
genl_rcv_msg+0x188/0x2c0
netlink_rcv_skb+0x54/0x100
genl_rcv+0x24/0x40
netlink_unicast+0x1a1/0x270
netlink_sendmsg+0x214/0x460
__sock_sendmsg+0x38/0x60
__sys_sendto+0x113/0x170
__x64_sys_sendto+0x20/0x30
do_syscall_64+0x40/0xe0
entry_SYSCALL_64_after_hwframe+0x46/0x4e
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&priv->state_lock);
lock((work_completion)(&rule->arfs_work));
lock(&priv->state_lock);
lock((work_completion)(&rule->arfs_work));
*** DEADLOCK ***
3 locks held by ethtool/386089:
#0: ffffffff82ea7210 (cb_lock){++++}-{3:3}, at: genl_rcv+0x15/0x40
#1: ffffffff82e94c88 (rtnl_mutex){+.+.}-{3:3}, at: ethnl_default_set_doit+0xd3/0x240
#2: ffff8884a1808cc0 (&priv->state_lock){+.+.}-{3:3}, at: mlx5e_ethtool_set_channels+0x53/0x200 [mlx5_core]
stack backtrace:
CPU: 15 PID: 386089 Comm: ethtool Tainted: G I 6.7.0-rc4_net_next_mlx5_5483eb2 #1
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x60/0xa0
check_noncircular+0x144/0x160
__lock_acquire+0x17b4/0x2c80
lock_acquire+0xd0/0x2b0
? __flush_work+0x74/0x4e0
? save_trace+0x3e/0x360
? __flush_work+0x74/0x4e0
__flush_work+0x7a/0x4e0
? __flush_work+0x74/0x4e0
? __lock_acquire+0xa78/0x2c80
? lock_acquire+0xd0/0x2b0
? mark_held_locks+0x49/0x70
__cancel_work_timer+0x131/0x1c0
? mark_held_locks+0x49/0x70
arfs_del_rules+0x143/0x1e0 [mlx5_core]
mlx5e_arfs_disable+0x1b/0x30 [mlx5_core]
mlx5e_ethtool_set_channels+0xcb/0x200 [mlx5_core]
ethnl_set_channels+0x28f/0x3b0
ethnl_default_set_doit+0xec/0x240
genl_family_rcv_msg_doit+0xd0/0x120
genl_rcv_msg+0x188/0x2c0
? ethnl_ops_begin+0xb0/0xb0
? genl_family_rcv_msg_dumpit+0xf0/0xf0
netlink_rcv_skb+0x54/0x100
genl_rcv+0x24/0x40
netlink_unicast+0x1a1/0x270
netlink_sendmsg+0x214/0x460
__sock_sendmsg+0x38/0x60
__sys_sendto+0x113/0x170
? do_user_addr_fault+0x53f/0x8f0
__x64_sys_sendto+0x20/0x30
do_syscall_64+0x40/0xe0
entry_SYSCALL_64_after_hwframe+0x46/0x4e
</TASK>
Fixes: 45bf454ae8 ("net/mlx5e: Enabling aRFS mechanism")
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240411115444.374475-7-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 37cc10da3a ]
The cited patch introduces the concept of buckets in LAG in hash mode.
However, the patch doesn't clear the number of buckets in the LAG
deactivation. This results in using the wrong number of buckets in
case user create a hash mode LAG and afterwards create a non-hash
mode LAG.
Hence, restore buckets number to default after hash mode LAG
deactivation.
Fixes: 352899f384 ("net/mlx5: Lag, use buckets in hash mode")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240411115444.374475-2-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68aba00483 ]
I noticed that only 3 out of the 4 input bits were used,
mt.key->flags & FLOW_DIS_IS_FRAGMENT was never checked.
In order to avoid a complicated maze, I converted it to
use a 16 byte mapping table.
As shown in the table below the old heuristics doesn't
always do the right thing, ie. when FLOW_DIS_IS_FRAGMENT=1/1
then it used to only match follow-up fragment packets.
Here are all the combinations, and their resulting new/old
VCAP key/mask filter:
/- FLOW_DIS_IS_FRAGMENT (key/mask)
| /- FLOW_DIS_FIRST_FRAG (key/mask)
| | /-- new VCAP fragment (key/mask)
v v v v- old VCAP fragment (key/mask)
0/0 0/0 -/- -/- impossible (due to entry cond. on mask)
0/0 0/1 -/- 0/3 !! invalid (can't match non-fragment + follow-up frag)
0/0 1/0 -/- -/- impossible (key > mask)
0/0 1/1 1/3 1/3 first fragment
0/1 0/0 0/3 3/3 !! not fragmented
0/1 0/1 0/3 3/3 !! not fragmented (+ not first fragment)
0/1 1/0 -/- -/- impossible (key > mask)
0/1 1/1 -/- 1/3 !! invalid (non-fragment and first frag)
1/0 0/0 -/- -/- impossible (key > mask)
1/0 0/1 -/- -/- impossible (key > mask)
1/0 1/0 -/- -/- impossible (key > mask)
1/0 1/1 -/- -/- impossible (key > mask)
1/1 0/0 1/1 3/3 !! some fragment
1/1 0/1 3/3 3/3 follow-up fragment
1/1 1/0 -/- -/- impossible (key > mask)
1/1 1/1 1/3 1/3 first fragment
In the datasheet the VCAP fragment values are documented as:
0 = no fragment
1 = initial fragment
2 = suspicious fragment
3 = valid follow-up fragment
Result: 3 combinations match the old behavior,
3 combinations have been corrected,
2 combinations are now invalid, and fail,
8 combinations are impossible.
It should now be aligned with how FLOW_DIS_IS_FRAGMENT
and FLOW_DIS_FIRST_FRAG is set in __skb_flow_dissect() in
net/core/flow_dissector.c
Since the VCAP fragment values are not a bitfield, we have
to ignore the suspicious fragment value, eg. when matching
on any kind of fragment with FLOW_DIS_IS_FRAGMENT=1/1.
Only compile tested, and logic tested in userspace, as I
unfortunately don't have access to this switch chip (yet).
Fixes: d6c2964db3 ("net: microchip: sparx5: Adding more tc flower keys for the IS2 VCAP")
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Tested-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20240411111321.114095-1-ast@fiberby.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 22dd70eb2c ]
Currently, we can read OOB data without MSG_OOB by using MSG_PEEK
when OOB data is sitting on the front row, which is apparently
wrong.
>>> from socket import *
>>> c1, c2 = socketpair(AF_UNIX, SOCK_STREAM)
>>> c1.send(b'a', MSG_OOB)
1
>>> c2.recv(1, MSG_PEEK | MSG_DONTWAIT)
b'a'
If manage_oob() is called when no data has been copied, we only
check if the socket enables SO_OOBINLINE or MSG_PEEK is not used.
Otherwise, the skb is returned as is.
However, here we should return NULL if MSG_PEEK is set and no data
has been copied.
Also, in such a case, we should not jump to the redo label because
we will be caught in the loop and hog the CPU until normal data
comes in.
Then, we need to handle skb == NULL case with the if-clause below
the manage_oob() block.
With this patch:
>>> from socket import *
>>> c1, c2 = socketpair(AF_UNIX, SOCK_STREAM)
>>> c1.send(b'a', MSG_OOB)
1
>>> c2.recv(1, MSG_PEEK | MSG_DONTWAIT)
Traceback (most recent call last):
File "<stdin>", line 1, in <module>
BlockingIOError: [Errno 11] Resource temporarily unavailable
Fixes: 314001f0bf ("af_unix: Add OOB support")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20240410171016.7621-3-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 283454c8a1 ]
When we call recv() for AF_UNIX socket, we first peek one skb and
calls manage_oob() to check if the skb is sent with MSG_OOB.
However, when we fetch the next (and the following) skb, manage_oob()
is not called now, leading a wrong behaviour.
Let's say a socket send()s "hello" with MSG_OOB and the peer tries
to recv() 5 bytes with MSG_PEEK. Here, we should get only "hell"
without 'o', but actually not:
>>> from socket import *
>>> c1, c2 = socketpair(AF_UNIX, SOCK_STREAM)
>>> c1.send(b'hello', MSG_OOB)
5
>>> c2.recv(5, MSG_PEEK)
b'hello'
The first skb fills 4 bytes, and the next skb is peeked but not
properly checked by manage_oob().
Let's move up the again label to call manage_oob() for evry skb.
With this patch:
>>> from socket import *
>>> c1, c2 = socketpair(AF_UNIX, SOCK_STREAM)
>>> c1.send(b'hello', MSG_OOB)
5
>>> c2.recv(5, MSG_PEEK)
b'hell'
Fixes: 314001f0bf ("af_unix: Add OOB support")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20240410171016.7621-2-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6db5dc7b35 ]
pppoe traffic reaching ingress path does not match the flowtable entry
because the pppoe header is expected to be at the network header offset.
This bug causes a mismatch in the flow table lookup, so pppoe packets
enter the classical forwarding path.
Fixes: 72efd585f7 ("netfilter: flowtable: add pppoe support")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87b3593bed ]
Ensure there is sufficient room to access the protocol field of the
PPPoe header. Validate it once before the flowtable lookup, then use a
helper function to access protocol field.
Reported-by: syzbot+b6f07e1c07ef40199081@syzkaller.appspotmail.com
Fixes: 72efd585f7 ("netfilter: flowtable: add pppoe support")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3cfc9ec039 ]
Pablo reports a crash with large batches of elements with a
back-to-back add/remove pattern. Quoting Pablo:
add_elem("00000000") timeout 100 ms
...
add_elem("0000000X") timeout 100 ms
del_elem("0000000X") <---------------- delete one that was just added
...
add_elem("00005000") timeout 100 ms
1) nft_pipapo_remove() removes element 0000000X
Then, KASAN shows a splat.
Looking at the remove function there is a chance that we will drop a
rule that maps to a non-deactivated element.
Removal happens in two steps, first we do a lookup for key k and return the
to-be-removed element and mark it as inactive in the next generation.
Then, in a second step, the element gets removed from the set/map.
The _remove function does not work correctly if we have more than one
element that share the same key.
This can happen if we insert an element into a set when the set already
holds an element with same key, but the element mapping to the existing
key has timed out or is not active in the next generation.
In such case its possible that removal will unmap the wrong element.
If this happens, we will leak the non-deactivated element, it becomes
unreachable.
The element that got deactivated (and will be freed later) will
remain reachable in the set data structure, this can result in
a crash when such an element is retrieved during lookup (stale
pointer).
Add a check that the fully matching key does in fact map to the element
that we have marked as inactive in the deactivation step.
If not, we need to continue searching.
Add a bug/warn trap at the end of the function as well, the remove
function must not ever be called with an invisible/unreachable/non-existent
element.
v2: avoid uneeded temporary variable (Stefano)
Fixes: 3c4287f620 ("nf_tables: Add set type for arbitrary concatenation of ranges")
Reported-by: Pablo Neira Ayuso <pablo@netfilter.org>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d78d867dce ]
nft_unregister_obj() can concurrent with __nft_obj_type_get(),
and there is not any protection when iterate over nf_tables_objects
list in __nft_obj_type_get(). Therefore, there is potential data-race
of nf_tables_objects list entry.
Use list_for_each_entry_rcu() to iterate over nf_tables_objects
list in __nft_obj_type_get(), and use rcu_read_lock() in the caller
nft_obj_type_get() to protect the entire type query process.
Fixes: e50092404c ("netfilter: nf_tables: add stateful objects")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f969eb84ce ]
nft_unregister_expr() can concurrent with __nft_expr_type_get(),
and there is not any protection when iterate over nf_tables_expressions
list in __nft_expr_type_get(). Therefore, there is potential data-race
of nf_tables_expressions list entry.
Use list_for_each_entry_rcu() to iterate over nf_tables_expressions
list in __nft_expr_type_get(), and use rcu_read_lock() in the caller
nft_expr_type_get() to protect the entire type query process.
Fixes: ef1f7df917 ("netfilter: nf_tables: expression ops overloading")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e3ba51ab24 upstream.
KVM/arm64 relies on TLBI RANGE feature to flush TLBs when the dirty
pages are collected by VMM and the page table entries become write
protected during live migration. Unfortunately, the operand passed
to the TLBI RANGE instruction isn't correctly sorted out due to the
commit 117940aa6e ("KVM: arm64: Define kvm_tlb_flush_vmid_range()").
It leads to crash on the destination VM after live migration because
TLBs aren't flushed completely and some of the dirty pages are missed.
For example, I have a VM where 8GB memory is assigned, starting from
0x40000000 (1GB). Note that the host has 4KB as the base page size.
In the middile of migration, kvm_tlb_flush_vmid_range() is executed
to flush TLBs. It passes MAX_TLBI_RANGE_PAGES as the argument to
__kvm_tlb_flush_vmid_range() and __flush_s2_tlb_range_op(). SCALE#3
and NUM#31, corresponding to MAX_TLBI_RANGE_PAGES, isn't supported
by __TLBI_RANGE_NUM(). In this specific case, -1 has been returned
from __TLBI_RANGE_NUM() for SCALE#3/2/1/0 and rejected by the loop
in the __flush_tlb_range_op() until the variable @scale underflows
and becomes -9, 0xffff708000040000 is set as the operand. The operand
is wrong since it's sorted out by __TLBI_VADDR_RANGE() according to
invalid @scale and @num.
Fix it by extending __TLBI_RANGE_NUM() to support the combination of
SCALE#3 and NUM#31. With the changes, [-1 31] instead of [-1 30] can
be returned from the macro, meaning the TLBs for 0x200000 pages in the
above example can be flushed in one shoot with SCALE#3 and NUM#31. The
macro TLBI_RANGE_MASK is dropped since no one uses it any more. The
comments are also adjusted accordingly.
Fixes: 117940aa6e ("KVM: arm64: Define kvm_tlb_flush_vmid_range()")
Cc: stable@kernel.org # v6.6+
Reported-by: Yihuang Yu <yihyu@redhat.com>
Suggested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Ryan Roberts <ryan.roberts@arm.com>
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Reviewed-by: Shaoqin Huang <shahuang@redhat.com>
Link: https://lore.kernel.org/r/20240405035852.1532010-2-gshan@redhat.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e2768b798a upstream.
In preparation for adding support for LPA2 to the tlb invalidation
routines, modify the algorithm used by range-based tlbi to start at the
highest 'scale' and decrement instead of starting at the lowest 'scale'
and incrementing. This new approach makes it possible to maintain 64K
alignment as we work through the range, until the last op (at scale=0).
This is required when LPA2 is enabled. (This part will be added in a
subsequent commit).
This change is separated into its own patch because it will also impact
non-LPA2 systems, and I want to make it easy to bisect in case it leads
to performance regression (see below for benchmarks that suggest this
should not be a problem).
The original commit (d1d3aa98 "arm64: tlb: Use the TLBI RANGE feature in
arm64") stated this as the reason for _incrementing_ scale:
However, in most scenarios, the pages = 1 when flush_tlb_range() is
called. Start from scale = 3 or other proper value (such as scale
=ilog2(pages)), will incur extra overhead. So increase 'scale' from 0
to maximum.
But pages=1 is already special cased by the non-range invalidation path,
which will take care of it the first time through the loop (both in the
original commit and in my change), so I don't think switching to
decrement scale should have any extra performance impact after all.
Indeed benchmarking kernel compilation, a TLBI-heavy workload, suggests
that this new approach actually _improves_ performance slightly (using a
virtual machine on Apple M2):
Table shows time to execute kernel compilation workload with 8 jobs,
relative to baseline without this patch (more negative number is
bigger speedup). Repeated 9 times across 3 system reboots:
| counter | mean | stdev |
|:----------|-----------:|----------:|
| real-time | -0.6% | 0.0% |
| kern-time | -1.6% | 0.5% |
| user-time | -0.4% | 0.1% |
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20231127111737.1897081-2-ryan.roberts@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 56f78615bc upstream.
After the commit d2689b6a86 ("net: usb: ax88179_178a: avoid two
consecutive device resets"), reset operation, in which the default mac
address from the device is read, is not executed from bind operation and
the random address, that is pregenerated just in case, is direclty written
the first time in the device, so the default one from the device is not
even read. This writing is not dangerous because is volatile and the
default mac address is not missed.
In order to avoid this and keep the simplification to have only one
reset and reduce the delays, restore the reset from bind operation and
remove the reset that is commanded from open operation. The behavior is
the same but everything is ready for usbnet_probe.
Tested with ASIX AX88179 USB Gigabit Ethernet devices.
Restore the old behavior for the rest of possible devices because I don't
have the hardware to test.
cc: stable@vger.kernel.org # 6.6+
Fixes: d2689b6a86 ("net: usb: ax88179_178a: avoid two consecutive device resets")
Reported-by: Jarkko Palviainen <jarkko.palviainen@gmail.com>
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Link: https://lore.kernel.org/r/20240417085524.219532-1-jtornosm@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e871abcda3 upstream.
The entropy accounting changes a static key when the RNG has
initialized, since it only ever initializes once. Static key changes,
however, cannot be made from atomic context, so depending on where the
last creditable entropy comes from, the static key change might need to
be deferred to a worker.
Previously the code used the execute_in_process_context() helper
function, which accounts for whether or not the caller is
in_interrupt(). However, that doesn't account for the case where the
caller is actually in process context but is holding a spinlock.
This turned out to be the case with input_handle_event() in
drivers/input/input.c contributing entropy:
[<ffffffd613025ba0>] die+0xa8/0x2fc
[<ffffffd613027428>] bug_handler+0x44/0xec
[<ffffffd613016964>] brk_handler+0x90/0x144
[<ffffffd613041e58>] do_debug_exception+0xa0/0x148
[<ffffffd61400c208>] el1_dbg+0x60/0x7c
[<ffffffd61400c000>] el1h_64_sync_handler+0x38/0x90
[<ffffffd613011294>] el1h_64_sync+0x64/0x6c
[<ffffffd613102d88>] __might_resched+0x1fc/0x2e8
[<ffffffd613102b54>] __might_sleep+0x44/0x7c
[<ffffffd6130b6eac>] cpus_read_lock+0x1c/0xec
[<ffffffd6132c2820>] static_key_enable+0x14/0x38
[<ffffffd61400ac08>] crng_set_ready+0x14/0x28
[<ffffffd6130df4dc>] execute_in_process_context+0xb8/0xf8
[<ffffffd61400ab30>] _credit_init_bits+0x118/0x1dc
[<ffffffd6138580c8>] add_timer_randomness+0x264/0x270
[<ffffffd613857e54>] add_input_randomness+0x38/0x48
[<ffffffd613a80f94>] input_handle_event+0x2b8/0x490
[<ffffffd613a81310>] input_event+0x6c/0x98
According to Guoyong, it's not really possible to refactor the various
drivers to never hold a spinlock there. And in_atomic() isn't reliable.
So, rather than trying to be too fancy, just punt the change in the
static key to a workqueue always. There's basically no drawback of doing
this, as the code already needed to account for the static key not
changing immediately, and given that it's just an optimization, there's
not exactly a hurry to change the static key right away, so deferal is
fine.
Reported-by: Guoyong Wang <guoyong.wang@mediatek.com>
Cc: stable@vger.kernel.org
Fixes: f5bda35fba ("random: use static branch for crng_ready()")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a4ea83a6e upstream.
While sched* events being traced and sched* events continuously happen,
"[xx] event tracing - enable/disable with subsystem level files" would
not stop as on some slower systems it seems to take forever.
Select the first 100 lines of output would be enough to judge whether
there are more than 3 types of sched events.
Fixes: 815b18ea66 ("ftracetest: Add basic event tracing test cases")
Cc: stable@vger.kernel.org
Signed-off-by: Yuanhe Shu <xiangzao@linux.alibaba.com>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Acked-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a4833e3aba upstream.
The rpcgss_context trace event acceptor field is a dynamically sized
string that records the "data" parameter. But this parameter is also
dependent on the "len" field to determine the size of the data.
It needs to use __string_len() helper macro where the length can be passed
in. It also incorrectly uses strncpy() to save it instead of
__assign_str(). As these macros can change, it is not wise to open code
them in trace events.
As of commit c759e60903 ("tracing: Remove __assign_str_len()"),
__assign_str() can be used for both __string() and __string_len() fields.
Before that commit, __assign_str_len() is required to be used. This needs
to be noted for backporting. (In actuality, commit c1fa617cae ("tracing:
Rework __assign_str() and __string() to not duplicate getting the string")
is the commit that makes __string_str_len() obsolete).
Cc: stable@vger.kernel.org
Fixes: 0c77668ddb ("SUNRPC: Introduce trace points in rpc_auth_gss.ko")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0e45882ca8 upstream.
Object debugging tools were sporadically reporting illegal attempts to
free a still active i915 VMA object when parking a GT believed to be idle.
[161.359441] ODEBUG: free active (active state 0) object: ffff88811643b958 object type: i915_active hint: __i915_vma_active+0x0/0x50 [i915]
[161.360082] WARNING: CPU: 5 PID: 276 at lib/debugobjects.c:514 debug_print_object+0x80/0xb0
...
[161.360304] CPU: 5 PID: 276 Comm: kworker/5:2 Not tainted 6.5.0-rc1-CI_DRM_13375-g003f860e5577+ #1
[161.360314] Hardware name: Intel Corporation Rocket Lake Client Platform/RocketLake S UDIMM 6L RVP, BIOS RKLSFWI1.R00.3173.A03.2204210138 04/21/2022
[161.360322] Workqueue: i915-unordered __intel_wakeref_put_work [i915]
[161.360592] RIP: 0010:debug_print_object+0x80/0xb0
...
[161.361347] debug_object_free+0xeb/0x110
[161.361362] i915_active_fini+0x14/0x130 [i915]
[161.361866] release_references+0xfe/0x1f0 [i915]
[161.362543] i915_vma_parked+0x1db/0x380 [i915]
[161.363129] __gt_park+0x121/0x230 [i915]
[161.363515] ____intel_wakeref_put_last+0x1f/0x70 [i915]
That has been tracked down to be happening when another thread is
deactivating the VMA inside __active_retire() helper, after the VMA's
active counter has been already decremented to 0, but before deactivation
of the VMA's object is reported to the object debugging tool.
We could prevent from that race by serializing i915_active_fini() with
__active_retire() via ref->tree_lock, but that wouldn't stop the VMA from
being used, e.g. from __i915_vma_retire() called at the end of
__active_retire(), after that VMA has been already freed by a concurrent
i915_vma_destroy() on return from the i915_active_fini(). Then, we should
rather fix the issue at the VMA level, not in i915_active.
Since __i915_vma_parked() is called from __gt_park() on last put of the
GT's wakeref, the issue could be addressed by holding the GT wakeref long
enough for __active_retire() to complete before that wakeref is released
and the GT parked.
I believe the issue was introduced by commit d939397303 ("drm/i915:
Remove the vma refcount") which moved a call to i915_active_fini() from
a dropped i915_vma_release(), called on last put of the removed VMA kref,
to i915_vma_parked() processing path called on last put of a GT wakeref.
However, its visibility to the object debugging tool was suppressed by a
bug in i915_active that was fixed two weeks later with commit e92eb246fe
("drm/i915/active: Fix missing debug object activation").
A VMA associated with a request doesn't acquire a GT wakeref by itself.
Instead, it depends on a wakeref held directly by the request's active
intel_context for a GT associated with its VM, and indirectly on that
intel_context's engine wakeref if the engine belongs to the same GT as the
VMA's VM. Those wakerefs are released asynchronously to VMA deactivation.
Fix the issue by getting a wakeref for the VMA's GT when activating it,
and putting that wakeref only after the VMA is deactivated. However,
exclude global GTT from that processing path, otherwise the GPU never goes
idle. Since __i915_vma_retire() may be called from atomic contexts, use
async variant of wakeref put. Also, to avoid circular locking dependency,
take care of acquiring the wakeref before VM mutex when both are needed.
v7: Add inline comments with justifications for:
- using untracked variants of intel_gt_pm_get/put() (Nirmoy),
- using async variant of _put(),
- not getting the wakeref in case of a global GTT,
- always getting the first wakeref outside vm->mutex.
v6: Since __i915_vma_active/retire() callbacks are not serialized, storing
a wakeref tracking handle inside struct i915_vma is not safe, and
there is no other good place for that. Use untracked variants of
intel_gt_pm_get/put_async().
v5: Replace "tile" with "GT" across commit description (Rodrigo),
- avoid mentioning multi-GT case in commit description (Rodrigo),
- explain why we need to take a temporary wakeref unconditionally inside
i915_vma_pin_ww() (Rodrigo).
v4: Refresh on top of commit 5e4e06e408 ("drm/i915: Track gt pm
wakerefs") (Andi),
- for more easy backporting, split out removal of former insufficient
workarounds and move them to separate patches (Nirmoy).
- clean up commit message and description a bit.
v3: Identify root cause more precisely, and a commit to blame,
- identify and drop former workarounds,
- update commit message and description.
v2: Get the wakeref before VM mutex to avoid circular locking dependency,
- drop questionable Fixes: tag.
Fixes: d939397303 ("drm/i915: Remove the vma refcount")
Closes: https://gitlab.freedesktop.org/drm/intel/issues/8875
Signed-off-by: Janusz Krzysztofik <janusz.krzysztofik@linux.intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Cc: Nirmoy Das <nirmoy.das@intel.com>
Cc: Andi Shyti <andi.shyti@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: stable@vger.kernel.org # v5.19+
Reviewed-by: Nirmoy Das <nirmoy.das@intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240305143747.335367-6-janusz.krzysztofik@linux.intel.com
(cherry picked from commit f3c71b2ded)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Janusz Krzysztofik <janusz.krzysztofik@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 350ab13e13 ]
The vb2 read support requests 1 buffer, leaving it to the driver
to increase this number to something that works.
Unfortunately, drivers do not deal with this reliably, and in fact
this caused problems for the bttv driver and reading from /dev/vbiX,
causing every other VBI frame to be all 0.
Instead, request as the number of buffers whatever is the maximum of
2 and q->min_buffers_needed+1.
In order to start streaming you need at least q->min_buffers_needed
queued buffers, so add 1 buffer for processing. And if that field
is 0, then choose 2 (again, one buffer is being filled while the
other one is being processed).
This certainly makes more sense than requesting just 1 buffer, and
the VBI bttv support is now working again.
It turns out that the old videobuf1 behavior of bttv was to allocate
8 (video) and 4 (vbi) buffers when used with read(). After the vb2
conversion that changed to 2 for both. With this patch it is 3, which
is really all you need.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: b7ec3212a7 ("media: bttv: convert to vb2")
Tested-by: Dr. David Alan Gilbert <dave@treblig.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46b1f1b839 ]
The function _dpu_hw_sspp_setup_scaler3() passes and
dpu_hw_setup_scaler3() uses scaler_blk.version to determine in which way
the scaler (QSEED3) block should be programmed. However up to now we
were not setting this field. Set it now, splitting the vig_sblk data
which has different version fields.
Reported-by: Marijn Suijten <marijn.suijten@somainline.org>
Fixes: 9b6f4fedaa ("drm/msm/dpu: Add SM6125 support")
Fixes: 27f0df03f3 ("drm/msm/dpu: Add SM6375 support")
Fixes: 3186acba5c ("drm/msm/dpu: Add SM6350 support")
Fixes: efcd010772 ("drm/msm/dpu: add support for SM8550")
Fixes: 4a352c2fc1 ("drm/msm/dpu: Introduce SC8280XP")
Fixes: 0e91bcbb00 ("drm/msm/dpu: Add SM8350 to hw catalog")
Fixes: 100d7ef699 ("drm/msm/dpu: add support for SM8450")
Fixes: 3581b7062c ("drm/msm/disp/dpu1: add support for display on SM6115")
Fixes: dabfdd89ea ("drm/msm/disp/dpu1: add inline rotation support for sc7280")
Fixes: f3af2d6ee9 ("drm/msm/dpu: Add SC8180x to hw catalog")
Fixes: 94391a14fc ("drm/msm/dpu1: Add MSM8998 to hw catalog")
Fixes: af776a3e1c ("drm/msm/dpu: add SM8250 to hw catalog")
Fixes: 386fced3f7 ("drm/msm/dpu: add SM8150 to hw catalog")
Fixes: b75ab05a34 ("msm:disp:dpu1: add scaler support on SC7180 display")
Fixes: 25fdd5933e ("drm/msm: Add SDM845 DPU support")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/570098/
Link: https://lore.kernel.org/r/20231201234234.2065610-2-dmitry.baryshkov@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d029c25b7 ]
check_timer_distribution() runs ten threads in a busy loop and tries to
test that the kernel distributes a process posix CPU timer signal to every
thread over time.
There is not guarantee that this is true even after commit bcb7ee7902
("posix-timers: Prefer delivery of signals to the current thread") because
that commit only avoids waking up the sleeping process leader thread, but
that has nothing to do with the actual signal delivery.
As the signal is process wide the first thread which observes sigpending
and wins the race to lock sighand will deliver the signal. Testing shows
that this hangs on a regular base because some threads never win the race.
The comment "This primarily tests that the kernel does not favour any one."
is wrong. The kernel does favour a thread which hits the timer interrupt
when CLOCK_PROCESS_CPUTIME_ID expires.
Rewrite the test so it only checks that the group leader sleeping in join()
never receives SIGALRM and the thread which burns CPU cycles receives all
signals.
In older kernels which do not have commit bcb7ee7902 ("posix-timers:
Prefer delivery of signals to the current thread") the test-case fails
immediately, the very 1st tick wakes the leader up. Otherwise it quickly
succeeds after 100 ticks.
CI testing wants to use newer selftest versions on stable kernels. In this
case the test is guaranteed to fail.
So check in the failure case whether the kernel version is less than v6.3
and skip the test result in that case.
[ tglx: Massaged change log, renamed the version check helper ]
Fixes: e797203fb3 ("selftests/timers/posix_timers: Test delivery of signals across threads")
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240409133802.GD29396@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 071af0c9e5 ]
Currently the posix_timers test does not produce KTAP output but rather a
custom format. This means that we only get a pass/fail for the suite, not
for each individual test that the suite does. Convert to using the standard
kselftest output functions which result in KTAP output being generated.
As part of this fix the printing of diagnostics in the unlikely event that
the pthread APIs fail, these were using perror() but the API functions
directly return an error code instead of setting errno.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Stable-dep-of: 6d029c25b7 ("selftests/timers/posix_timers: Reimplement check_timer_distribution()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 825edc8bc7 ]
Make the seamless_m_n flag more like the update_pipe fastset
flag, ie. the flag will only be set if we need to do the seamless
M/N update, and in all other cases the flag is cleared. Also
rename the flag to update_m_n to make it more clear it's similar
to update_pipe.
I believe special casing seamless_m_n like this makes sense
as it also affects eg. vblank evasion. We can potentially avoid
some vblank evasion tricks, simplify some checks, and hopefully
will help with the VRR vs. M/N mess.
Cc: Manasi Navare <navaremanasi@chromium.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230901130440.2085-6-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <navaremanasi@chromium.org>
Stable-dep-of: 4a36e46df7 ("drm/i915: Disable live M/N updates when using bigjoiner")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 691dec86ac ]
In order to reconcile seamless M/N updates with VRR we'll
need to defer the fastset VRR enable to happen after the
seamless M/N update (which happens during the vblank evade
critical section). So just push the VRR enable to be the last
thing during the update.
This will also affect the vblank evasion as the transcoder
will now still be running with the old VRR state during
the vblank evasion. So just grab the timings always from the
old crtc state during any non-modeset commit, and also grab
the current state of VRR from the active timings (as we disable
VRR before vblank evasion during fastsets).
This also fixes vblank evasion for seamless M/N updates as
we now properly account for the fact that the M/N update
happens after vblank evasion.
Cc: Manasi Navare <navaremanasi@chromium.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230901130440.2085-5-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <navaremanasi@chromium.org>
Reviewed-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Stable-dep-of: 4a36e46df7 ("drm/i915: Disable live M/N updates when using bigjoiner")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6154cc9177 ]
Currently we only consider the relationship of the
old and new CDCLK frequencies when determining whether
to do the repgramming from intel_set_cdclk_pre_plane_update()
or intel_set_cdclk_post_plane_update().
It is technically possible to have a situation where the
CDCLK frequency is decreasing, but the voltage_level is
increasing due a DDI port. In this case we should bump
the voltage level already in intel_set_cdclk_pre_plane_update()
(so that the voltage_level will have been increased by the
time the port gets enabled), while leaving the CDCLK frequency
unchanged (as active planes/etc. may still depend on it).
We can then reduce the CDCLK frequency to its final value
from intel_set_cdclk_post_plane_update().
In order to handle that correctly we shall construct a
suitable amalgam of the old and new cdclk states in
intel_set_cdclk_pre_plane_update().
And we can simply call intel_set_cdclk() unconditionally
in both places as it will not do anything if nothing actually
changes vs. the current hw state.
v2: Handle cdclk_state->disable_pipes
v3: Only synchronize the cd2x update against the pipe's vblank
when the cdclk frequency is changing during the current
commit phase (Gustavo)
Cc: stable@vger.kernel.org
Cc: Gustavo Sousa <gustavo.sousa@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240402155016.13733-3-ville.syrjala@linux.intel.com
(cherry picked from commit 34d127e2bd)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a05ad21d7 ]
Avoid refreshing DFS referral with refpath_lock acquired as the I/O
could block for a while due to a potentially disconnected or slow DFS
root server and then making other threads - that use same @server and
don't require a DFS root server - unable to make any progress.
Cc: stable@vger.kernel.org # 6.4+
Signed-off-by: Paulo Alcantara (Red Hat) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d8392c203e ]
In analyzing problems, one missing piece of debug data is when the
mount occurred. A related problem is when collecting stats we don't
know the period of time the stats covered, ie when this set of stats
for the tcon started to be collected. To make debugging easier track
the stats begin time. Set it when the mount occurred at mount time,
and reset it to current time whenever stats are reset. For example,
...
1) \\localhost\test
SMBs: 14 since 2024-01-17 22:17:30 UTC
Bytes read: 0 Bytes written: 0
Open files: 0 total (local), 0 open on server
TreeConnects: 1 total 0 failed
TreeDisconnects: 0 total 0 failed
...
2) \\localhost\scratch
SMBs: 24 since 2024-01-17 22:16:04 UTC
Bytes read: 0 Bytes written: 0
Open files: 0 total (local), 0 open on server
TreeConnects: 1 total 0 failed
TreeDisconnects: 0 total 0 failed
...
Note the time "since ... UTC" is now displayed in /proc/fs/cifs/Stats
for each share that is mounted.
Suggested-by: Shyam Prasad N <sprasad@microsoft.com>
Reviewed-by: Bharath SM <bharathsm@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Stable-dep-of: 062a7f0ff4 ("smb: client: guarantee refcounted children from parent session")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24a9799aa8 ]
The UAF bug is due to smb2_reconnect_server() accessing a session that
is already being teared down by another thread that is executing
__cifs_put_smb_ses(). This can happen when (a) the client has
connection to the server but no session or (b) another thread ends up
setting @ses->ses_status again to something different than
SES_EXITING.
To fix this, we need to make sure to unconditionally set
@ses->ses_status to SES_EXITING and prevent any other threads from
setting a new status while we're still tearing it down.
The following can be reproduced by adding some delay to right after
the ipc is freed in __cifs_put_smb_ses() - which will give
smb2_reconnect_server() worker a chance to run and then accessing
@ses->ipc:
kinit ...
mount.cifs //srv/share /mnt/1 -o sec=krb5,nohandlecache,echo_interval=10
[disconnect srv]
ls /mnt/1 &>/dev/null
sleep 30
kdestroy
[reconnect srv]
sleep 10
umount /mnt/1
...
CIFS: VFS: Verify user has a krb5 ticket and keyutils is installed
CIFS: VFS: \\srv Send error in SessSetup = -126
CIFS: VFS: Verify user has a krb5 ticket and keyutils is installed
CIFS: VFS: \\srv Send error in SessSetup = -126
general protection fault, probably for non-canonical address
0x6b6b6b6b6b6b6b6b: 0000 [#1] PREEMPT SMP NOPTI
CPU: 3 PID: 50 Comm: kworker/3:1 Not tainted 6.9.0-rc2 #1
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-1.fc39
04/01/2014
Workqueue: cifsiod smb2_reconnect_server [cifs]
RIP: 0010:__list_del_entry_valid_or_report+0x33/0xf0
Code: 4f 08 48 85 d2 74 42 48 85 c9 74 59 48 b8 00 01 00 00 00 00 ad
de 48 39 c2 74 61 48 b8 22 01 00 00 00 00 74 69 <48> 8b 01 48 39 f8 75
7b 48 8b 72 08 48 39 c6 0f 85 88 00 00 00 b8
RSP: 0018:ffffc900001bfd70 EFLAGS: 00010a83
RAX: dead000000000122 RBX: ffff88810da53838 RCX: 6b6b6b6b6b6b6b6b
RDX: 6b6b6b6b6b6b6b6b RSI: ffffffffc02f6878 RDI: ffff88810da53800
RBP: ffff88810da53800 R08: 0000000000000001 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000001 R12: ffff88810c064000
R13: 0000000000000001 R14: ffff88810c064000 R15: ffff8881039cc000
FS: 0000000000000000(0000) GS:ffff888157c00000(0000)
knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fe3728b1000 CR3: 000000010caa4000 CR4: 0000000000750ef0
PKRU: 55555554
Call Trace:
<TASK>
? die_addr+0x36/0x90
? exc_general_protection+0x1c1/0x3f0
? asm_exc_general_protection+0x26/0x30
? __list_del_entry_valid_or_report+0x33/0xf0
__cifs_put_smb_ses+0x1ae/0x500 [cifs]
smb2_reconnect_server+0x4ed/0x710 [cifs]
process_one_work+0x205/0x6b0
worker_thread+0x191/0x360
? __pfx_worker_thread+0x10/0x10
kthread+0xe2/0x110
? __pfx_kthread+0x10/0x10
ret_from_fork+0x34/0x50
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1a/0x30
</TASK>
Cc: stable@vger.kernel.org
Signed-off-by: Paulo Alcantara (Red Hat) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c37ed2d7d0 ]
If @ses->chan_count <= 1, then for-loop body will not be executed so
no need to check it twice.
Reviewed-by: Shyam Prasad N <sprasad@microsoft.com>
Signed-off-by: Paulo Alcantara (SUSE) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Stable-dep-of: 24a9799aa8 ("smb: client: fix UAF in smb2_reconnect_server()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
The OV5647 declares that it wants a non-continuous clock in its endpoint
configuration. However, it does not expose this information via
get_mbus_config. Even if it would implement get_mbus_config the
bcm2835-unicam driver would not evaluate the flags field of it.
By also specifying clock-noncontinuous on the CSI endpoint itself, the
CSI driver properly picks up the requests and enables the non-continuous
clock mode.
Signed-off-by: Christian Speich <christian@spei.ch>
Support a wider range of pixel clock rates. The driver will round
pixclock up to 108MHz/n but tries to honour the desired image width
and position (of the centre of the display relative to HSYNC_STARTs).
This adds complexity but removes the need for separate 13.5MHz and
15.428MHz modes.
Support "fake" double-rate progressive modes (in which only every
2nd scanline is displayed). To work around aspect ratio issues.
Add Monochrome TV mode support. Add "vintage" modes (544x380i for
System A; 848x738i for System E) when configured for Monochrome.
Add a way to create a "custom" display mode from a module parameter.
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
The framework now handles reading orientation from DT, therefore
remove the custom get_orientation hook from panel-simple.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
"rotation" is listed as a standard property of panels in panel-common.yaml,
therefore it would be logical to process that from within the core
code should a panel driver not implement the get_orientation hook.
Call of_drm_get_panel_orientation from
drm_connector_set_orientation_from_panel to get that information.
This removes the need for any boiler-plate in panel drivers for calling
drm_connector_set_orientation_from_panel or
drm_connector_set_panel_orientation.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Escape clock divider was fixed at 5, which is correct at 800Mbps/lane
but increasingly out of spec for higher rates. Compute it correctly.
High speed timeout was fixed at 5*512 == 2560 byte-clocks per lane.
Compute it conservatively to be 8/7 times the line period (assuming
there will be a transition to LP some time during each scanline?)
keeping the old value as a lower bound. Increase LPRX TO to 1024,
and BTA TO to 0xb00 (same value as in bridge/synopsys/dw-mipi-dsi).
(No change to LP_CMD_TIM. To do: compute this correctly.)
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
The intention of the vc4.force_hotplug setting is to
ignore hotplug completely.
It can be used when a display toggles hotplug when
switching AV inputs, going into standby or changing a
KVM switch, and some side effect of that is unwanted.
It turns out while vc4.force_hotplug currently makes
hotplug always read as asserted, that isn't enough to
stop drm doing lots of stuff, including re-reading
the edid.
An example of what drm does with a hotplug deasert/assert
and vc4.force_hotplug=1 currently is:
https://paste.debian.net/hidden/dc07434b/
That is unwanted. Lets ignore the hotplug interrupt
completely so drm is blissfully unaware of the hotplug change.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
The 8-bit and 16-bit mono formats were missing the appropriate remap
entries in the format table.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
This code:
for_each_sg(sgl, sg, sg_len, i)
num_sgs += DIV_ROUND_UP(sg_dma_len(sg), axi_block_len);
determines how many hw_desc are allocated.
If sg_dma_len(sg)=0 we don't allocate for this sgl.
However in the next loop, we will increment loop
for this case, and loop gets higher than num_sgs
and we trample memory.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Setting strict_gpiod disables the GPIO output persistence, such that
pins are returned to being inputs when they are released. Note that
this applies to the GPIO/pinctrl driver for the user-facing GPIOs,
not the SoC GPIOs on Pi 5.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Setting strict_gpiod to Y makes libgpiod and the gpiod utilities behave
as documented, i.e. pins are returned to being GPIO inputs when they are
released.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Setting strict_gpiod to Y makes libgpiod and the gpiod utilities behave
as documented, i.e. pins are returned to being GPIO inputs when they are
released.
drivers/pinctrl/bcm/pinctrl-bcm2835.c
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
gpio-ranges declares a relationship between pinctrl and GPIO
controllers. It is required for "strict" mode to work.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Unicam now takes an optional GPIO to expose frame start/end timing,
so add an override to configure that.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The firmware stops vc4-kms-v3d and vc4-fkms-v3d loading if the
system has less than 512MB of RAM. It can work if gpu_mem and
CMA heap size are set appropriately, but can't be guaranteed.
Document this restriction.
Also drops Eric's name from the overlay description as it
isn't relevant or accurate anymore.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The magic required to make requesting a GPIO automatically change the
pinmux settings is currently absent. Work around that by explicitly
requesting that the ANT pins be in GPIO mode.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Requesting a GPIO as an interrupt source does not automatically make it
an input (or even a GPIO pin). Add the necessary pinctrl nodes to the
overlays that don't already do this.
See: https://github.com/raspberrypi/linux/issues/6106
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The soundcard drivers originally used snd_pcm_format_physical_width,
but a later commit changed that to snd_pcm_format_width because the
in-memory sample storage width should not be a factor in determining
the bclk_ratio. However, the physical width rounds the sample bits up
to the nearest power of 2, which makes it easier to find integer clock
divisors.
Restore the old behaviour, but with an implementation that makes it
clear what is going on.
See: https://github.com/raspberrypi/linux/issues/6104
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The property should be a u8, and should target the non-periodic
SuperSpeed transmit FIFO not the periodic one.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
commit 7b1f6b5aae upstream.
Currently we always reprogram CDCLK from the
intel_set_cdclk_pre_plane_update() when using squash/crawl.
The code only works correctly for the cd2x update or full
modeset cases, and it was simply never updated to deal with
squash/crawl.
If the CDCLK frequency is increasing we must reprogram it
before we do anything else that might depend on the new
higher frequency, and conversely we must not decrease
the frequency until everything that might still depend
on the old higher frequency has been dealt with.
Since cdclk_state->pipe is only relevant when doing a cd2x
update we can't use it to determine the correct sequence
during squash/crawl. To that end introduce cdclk_state->disable_pipes
which simply indicates that we must perform the update
while the pipes are disable (ie. during
intel_set_cdclk_pre_plane_update()). Otherwise we use the
same old vs. new CDCLK frequency comparsiong as for cd2x
updates.
The only remaining problem case is when the voltage_level
needs to increase due to a DDI port, but the CDCLK frequency
is decreasing (and not all pipes are being disabled). The
current approach will not bump the voltage level up until
after the port has already been enabled, which is too late.
But we'll take care of that case separately.
v2: Don't break the "must disable pipes case"
v3: Keep the on stack 'pipe' for future use
Cc: stable@vger.kernel.org
Fixes: d62686ba3b ("drm/i915/adl_p: CDCLK crawl support for ADL")
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240402155016.13733-2-ville.syrjala@linux.intel.com
(cherry picked from commit 3aecee90ac)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0485730d2 upstream.
So we are using the 'ia32_cap' value in a number of places,
which got its name from MSR_IA32_ARCH_CAPABILITIES MSR register.
But there's very little 'IA32' about it - this isn't 32-bit only
code, nor does it originate from there, it's just a historic
quirk that many Intel MSR names are prefixed with IA32_.
This is already clear from the helper method around the MSR:
x86_read_arch_cap_msr(), which doesn't have the IA32 prefix.
So rename 'ia32_cap' to 'x86_arch_cap_msr' to be consistent with
its role and with the naming of the helper function.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Nikolay Borisov <nik.borisov@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Sean Christopherson <seanjc@google.com>
Link: https://lore.kernel.org/r/9592a18a814368e75f8f4b9d74d3883aa4fd1eaf.1712813475.git.jpoimboe@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ce344beac upstream.
When done from a virtual machine, instructions that touch APIC memory
must be emulated. By convention, MMIO accesses are typically performed
via io.h helpers such as readl() or writeq() to simplify instruction
emulation/decoding (ex: in KVM hosts and SEV guests) [0].
Currently, native_apic_mem_read() does not follow this convention,
allowing the compiler to emit instructions other than the MOV
instruction generated by readl(). In particular, when the kernel is
compiled with clang and run as a SEV-ES or SEV-SNP guest, the compiler
would emit a TESTL instruction which is not supported by the SEV-ES
emulator, causing a boot failure in that environment. It is likely the
same problem would happen in a TDX guest as that uses the same
instruction emulator as SEV-ES.
To make sure all emulators can emulate APIC memory reads via MOV, use
the readl() function in native_apic_mem_read(). It is expected that any
emulator would support MOV in any addressing mode as it is the most
generic and is what is usually emitted currently.
The TESTL instruction is emitted when native_apic_mem_read() is inlined
into apic_mem_wait_icr_idle(). The emulator comes from
insn_decode_mmio() in arch/x86/lib/insn-eval.c. It's not worth it to
extend insn_decode_mmio() to support more instructions since, in theory,
the compiler could choose to output nearly any instruction for such
reads which would bloat the emulator beyond reason.
[0] https://lore.kernel.org/all/20220405232939.73860-12-kirill.shutemov@linux.intel.com/
[ bp: Massage commit message, fix typos. ]
Signed-off-by: Adam Dunlap <acdunlap@google.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Kevin Loughlin <kevinloughlin@google.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20240318230927.2191933-1-acdunlap@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ed366de8ec upstream.
Building with clang results in the following warning:
posix_timers.c:69:6: warning: absolute value function 'abs' given an
argument of type 'long long' but has parameter of type 'int' which may
cause truncation of value [-Wabsolute-value]
if (abs(diff - DELAY * USECS_PER_SEC) > USECS_PER_SEC / 2) {
^
So switch to using llabs() instead.
Fixes: 0bc4b0cf15 ("selftests: add basic posix timers selftests")
Signed-off-by: John Stultz <jstultz@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240410232637.4135564-3-jstultz@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f337a6a21e upstream.
Initialize cpu_mitigations to CPU_MITIGATIONS_OFF if the kernel is built
with CONFIG_SPECULATION_MITIGATIONS=n, as the help text quite clearly
states that disabling SPECULATION_MITIGATIONS is supposed to turn off all
mitigations by default.
│ If you say N, all mitigations will be disabled. You really
│ should know what you are doing to say so.
As is, the kernel still defaults to CPU_MITIGATIONS_AUTO, which results in
some mitigations being enabled in spite of SPECULATION_MITIGATIONS=n.
Fixes: f43b9876e8 ("x86/retbleed: Add fine grained Kconfig knobs")
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Daniel Sneddon <daniel.sneddon@linux.intel.com>
Cc: stable@vger.kernel.org
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lore.kernel.org/r/20240409175108.1512861-2-seanjc@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dec8ced871 upstream.
On x86 each struct cpu_hw_events maintains a table for counter assignment but
it missed to update one for the deleted event in x86_pmu_del(). This
can make perf_clear_dirty_counters() reset used counter if it's called
before event scheduling or enabling. Then it would return out of range
data which doesn't make sense.
The following code can reproduce the problem.
$ cat repro.c
#include <pthread.h>
#include <stdio.h>
#include <stdlib.h>
#include <unistd.h>
#include <linux/perf_event.h>
#include <sys/ioctl.h>
#include <sys/mman.h>
#include <sys/syscall.h>
struct perf_event_attr attr = {
.type = PERF_TYPE_HARDWARE,
.config = PERF_COUNT_HW_CPU_CYCLES,
.disabled = 1,
};
void *worker(void *arg)
{
int cpu = (long)arg;
int fd1 = syscall(SYS_perf_event_open, &attr, -1, cpu, -1, 0);
int fd2 = syscall(SYS_perf_event_open, &attr, -1, cpu, -1, 0);
void *p;
do {
ioctl(fd1, PERF_EVENT_IOC_ENABLE, 0);
p = mmap(NULL, 4096, PROT_READ, MAP_SHARED, fd1, 0);
ioctl(fd2, PERF_EVENT_IOC_ENABLE, 0);
ioctl(fd2, PERF_EVENT_IOC_DISABLE, 0);
munmap(p, 4096);
ioctl(fd1, PERF_EVENT_IOC_DISABLE, 0);
} while (1);
return NULL;
}
int main(void)
{
int i;
int n = sysconf(_SC_NPROCESSORS_ONLN);
pthread_t *th = calloc(n, sizeof(*th));
for (i = 0; i < n; i++)
pthread_create(&th[i], NULL, worker, (void *)(long)i);
for (i = 0; i < n; i++)
pthread_join(th[i], NULL);
free(th);
return 0;
}
And you can see the out of range data using perf stat like this.
Probably it'd be easier to see on a large machine.
$ gcc -o repro repro.c -pthread
$ ./repro &
$ sudo perf stat -A -I 1000 2>&1 | awk '{ if (length($3) > 15) print }'
1.001028462 CPU6 196,719,295,683,763 cycles # 194290.996 GHz (71.54%)
1.001028462 CPU3 396,077,485,787,730 branch-misses # 15804359784.80% of all branches (71.07%)
1.001028462 CPU17 197,608,350,727,877 branch-misses # 14594186554.56% of all branches (71.22%)
2.020064073 CPU4 198,372,472,612,140 cycles # 194681.113 GHz (70.95%)
2.020064073 CPU6 199,419,277,896,696 cycles # 195720.007 GHz (70.57%)
2.020064073 CPU20 198,147,174,025,639 cycles # 194474.654 GHz (71.03%)
2.020064073 CPU20 198,421,240,580,145 stalled-cycles-frontend # 100.14% frontend cycles idle (70.93%)
3.037443155 CPU4 197,382,689,923,416 cycles # 194043.065 GHz (71.30%)
3.037443155 CPU20 196,324,797,879,414 cycles # 193003.773 GHz (71.69%)
3.037443155 CPU5 197,679,956,608,205 stalled-cycles-backend # 1315606428.66% backend cycles idle (71.19%)
3.037443155 CPU5 198,571,860,474,851 instructions # 13215422.58 insn per cycle
It should move the contents in the cpuc->assign as well.
Fixes: 5471eea5d3 ("perf/x86: Reset the dirty counter to prevent the leak for an RDPMC task")
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240306061003.1894224-1-namhyung@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df9ace7647 upstream.
A smp_rmb() has been missed in vhost_enable_notify(), inspired by
Will. Otherwise, it's not ensured the available ring entries pushed
by guest can be observed by vhost in time, leading to stale available
ring entries fetched by vhost in vhost_get_vq_desc(), as reported by
Yihuang Yu on NVidia's grace-hopper (ARM64) platform.
/home/gavin/sandbox/qemu.main/build/qemu-system-aarch64 \
-accel kvm -machine virt,gic-version=host -cpu host \
-smp maxcpus=1,cpus=1,sockets=1,clusters=1,cores=1,threads=1 \
-m 4096M,slots=16,maxmem=64G \
-object memory-backend-ram,id=mem0,size=4096M \
: \
-netdev tap,id=vnet0,vhost=true \
-device virtio-net-pci,bus=pcie.8,netdev=vnet0,mac=52:54:00:f1:26:b0
:
guest# netperf -H 10.26.1.81 -l 60 -C -c -t UDP_STREAM
virtio_net virtio0: output.0:id 100 is not a head!
Add the missed smp_rmb() in vhost_enable_notify(). When it returns true,
it means there's still pending tx buffers. Since it might read indices,
so it still can bypass the smp_rmb() in vhost_get_vq_desc(). Note that
it should be safe until vq->avail_idx is changed by commit d3bb267bbd
("vhost: cache avail index in vhost_enable_notify()").
Fixes: d3bb267bbd ("vhost: cache avail index in vhost_enable_notify()")
Cc: <stable@kernel.org> # v5.18+
Reported-by: Yihuang Yu <yihyu@redhat.com>
Suggested-by: Will Deacon <will@kernel.org>
Signed-off-by: Gavin Shan <gshan@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20240328002149.1141302-3-gshan@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 22e1992cf7 upstream.
A smp_rmb() has been missed in vhost_vq_avail_empty(), spotted by
Will. Otherwise, it's not ensured the available ring entries pushed
by guest can be observed by vhost in time, leading to stale available
ring entries fetched by vhost in vhost_get_vq_desc(), as reported by
Yihuang Yu on NVidia's grace-hopper (ARM64) platform.
/home/gavin/sandbox/qemu.main/build/qemu-system-aarch64 \
-accel kvm -machine virt,gic-version=host -cpu host \
-smp maxcpus=1,cpus=1,sockets=1,clusters=1,cores=1,threads=1 \
-m 4096M,slots=16,maxmem=64G \
-object memory-backend-ram,id=mem0,size=4096M \
: \
-netdev tap,id=vnet0,vhost=true \
-device virtio-net-pci,bus=pcie.8,netdev=vnet0,mac=52:54:00:f1:26:b0
:
guest# netperf -H 10.26.1.81 -l 60 -C -c -t UDP_STREAM
virtio_net virtio0: output.0:id 100 is not a head!
Add the missed smp_rmb() in vhost_vq_avail_empty(). When tx_can_batch()
returns true, it means there's still pending tx buffers. Since it might
read indices, so it still can bypass the smp_rmb() in vhost_get_vq_desc().
Note that it should be safe until vq->avail_idx is changed by commit
275bf960ac ("vhost: better detection of available buffers").
Fixes: 275bf960ac ("vhost: better detection of available buffers")
Cc: <stable@kernel.org> # v4.11+
Reported-by: Yihuang Yu <yihyu@redhat.com>
Suggested-by: Will Deacon <will@kernel.org>
Signed-off-by: Gavin Shan <gshan@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20240328002149.1141302-2-gshan@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d86c2b394 upstream.
lpcg's arg0 should use clock indices instead of index.
pwm0_lpcg: clock-controller@5d400000 {
... // Col1 Col2
clocks = <&clk IMX_SC_R_PWM_0 IMX_SC_PM_CLK_PER>, // 0 0
<&clk IMX_SC_R_PWM_0 IMX_SC_PM_CLK_PER>, // 1 1
<&clk IMX_SC_R_PWM_0 IMX_SC_PM_CLK_PER>, // 2 4
<&lsio_bus_clk>, // 3 5
<&clk IMX_SC_R_PWM_0 IMX_SC_PM_CLK_PER>; // 4 6
clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_1>,
<IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_5>,
<IMX_LPCG_CLK_6>;
};
Col1: index, which existing dts try to get.
Col2: actual index in lpcg driver.
pwm1 {
....
clocks = <&pwm1_lpcg 4>, <&pwm1_lpcg 1>;
^^ ^^
should be:
clocks = <&pwm1_lpcg IMX_LPCG_CLK_6>, <&pwm1_lpcg IMX_LPCG_CLK_1>;
};
Arg0 is divided by 4 in lpcg driver, so index 0 and 1 will be get by pwm
driver, which are same as IMX_LPCG_CLK_6 and IMX_LPCG_CLK_1. Even it can
work, but code logic is wrong. Fixed it by use correct indices.
Cc: stable@vger.kernel.org
Fixes: 23fa99b205 ("arm64: dts: freescale: imx8-ss-lsio: add support for lsio_pwm0-3")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 325f3fb551 upstream.
When unloading a module, its state is changing MODULE_STATE_LIVE ->
MODULE_STATE_GOING -> MODULE_STATE_UNFORMED. Each change will take
a time. `is_module_text_address()` and `__module_text_address()`
works with MODULE_STATE_LIVE and MODULE_STATE_GOING.
If we use `is_module_text_address()` and `__module_text_address()`
separately, there is a chance that the first one is succeeded but the
next one is failed because module->state becomes MODULE_STATE_UNFORMED
between those operations.
In `check_kprobe_address_safe()`, if the second `__module_text_address()`
is failed, that is ignored because it expected a kernel_text address.
But it may have failed simply because module->state has been changed
to MODULE_STATE_UNFORMED. In this case, arm_kprobe() will try to modify
non-exist module text address (use-after-free).
To fix this problem, we should not use separated `is_module_text_address()`
and `__module_text_address()`, but use only `__module_text_address()`
once and do `try_module_get(module)` which is only available with
MODULE_STATE_LIVE.
Link: https://lore.kernel.org/all/20240410015802.265220-1-zhengyejian1@huawei.com/
Fixes: 28f6c37a29 ("kprobes: Forbid probing on trampoline and BPF code areas")
Cc: stable@vger.kernel.org
Signed-off-by: Zheng Yejian <zhengyejian1@huawei.com>
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 211de93367 upstream.
The transaction is only able to free PERTRANS reservations for a root
once that root has been recorded with the TRANS tag on the roots radix
tree. Therefore, until we are sure that this root will get tagged, it
isn't safe to convert. Generally, this is not an issue as *some*
transaction will likely tag the root before long and this reservation
will get freed in that transaction, but technically it could stick
around until unmount and result in a warning about leaked metadata
reservation space.
This path is most exercised by running the generic/269 fstest with
CONFIG_BTRFS_DEBUG.
Fixes: a649684967 ("btrfs: fix start transaction qgroup rsv double free")
CC: stable@vger.kernel.org # 6.6+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Boris Burkov <boris@bur.io>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 71537e35c3 upstream.
When running delayed inode updates, we do not record the inode's root in
the transaction, but we do allocate PREALLOC and thus converted PERTRANS
space for it. To be sure we free that PERTRANS meta rsv, we must ensure
that we record the root in the transaction.
Fixes: 4f5427ccce ("btrfs: delayed-inode: Use new qgroup meta rsv for delayed inode and item")
CC: stable@vger.kernel.org # 6.1+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Boris Burkov <boris@bur.io>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 74e9795812 upstream.
Create subvolume, create snapshot and delete subvolume all use
btrfs_subvolume_reserve_metadata() to reserve metadata for the changes
done to the parent subvolume's fs tree, which cannot be mediated in the
normal way via start_transaction. When quota groups (squota or qgroups)
are enabled, this reserves qgroup metadata of type PREALLOC. Once the
operation is associated to a transaction, we convert PREALLOC to
PERTRANS, which gets cleared in bulk at the end of the transaction.
However, the error paths of these three operations were not implementing
this lifecycle correctly. They unconditionally converted the PREALLOC to
PERTRANS in a generic cleanup step regardless of errors or whether the
operation was fully associated to a transaction or not. This resulted in
error paths occasionally converting this rsv to PERTRANS without calling
record_root_in_trans successfully, which meant that unless that root got
recorded in the transaction by some other thread, the end of the
transaction would not free that root's PERTRANS, leaking it. Ultimately,
this resulted in hitting a WARN in CONFIG_BTRFS_DEBUG builds at unmount
for the leaked reservation.
The fix is to ensure that every qgroup PREALLOC reservation observes the
following properties:
1. any failure before record_root_in_trans is called successfully
results in freeing the PREALLOC reservation.
2. after record_root_in_trans, we convert to PERTRANS, and now the
transaction owns freeing the reservation.
This patch enforces those properties on the three operations. Without
it, generic/269 with squotas enabled at mkfs time would fail in ~5-10
runs on my system. With this patch, it ran successfully 1000 times in a
row.
Fixes: e85fde5162 ("btrfs: qgroup: fix qgroup meta rsv leak for subvolume operations")
CC: stable@vger.kernel.org # 6.1+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Boris Burkov <boris@bur.io>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 141fb8cd20 upstream.
We use add_root_meta_rsv and sub_root_meta_rsv to track prealloc and
pertrans reservations for subvolumes when quotas are enabled. The
convert function does not properly increment pertrans after decrementing
prealloc, so the count is not accurate.
Note: we check that the fs is not read-only to mirror the logic in
qgroup_convert_meta, which checks that before adding to the pertrans rsv.
Fixes: 8287475a20 ("btrfs: qgroup: Use root::qgroup_meta_rsv_* to record qgroup meta reserved space")
CC: stable@vger.kernel.org # 6.1+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Boris Burkov <boris@bur.io>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7c42bf4d3 upstream.
This patch uses addition assignment operator (+=) to append strings
instead of duplicating the variable name in mptcp_connect.sh and
mptcp_join.sh.
This can make the statements shorter.
Note: in mptcp_connect.sh, add a local variable extra in do_transfer to
save the various extra warning logs, using += to append it. And add a
new variable tc_info to save various tc info, also using += to append it.
This can make the code more readable and prepare for the next commit.
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://lore.kernel.org/r/20240308-upstream-net-next-20240308-selftests-mptcp-unification-v1-8-4f42c347b653@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
[ Conflicts in mptcp_connect.sh: this commit was supposed to be
backported before commit 7a1b3490f4 ("mptcp: don't account accept()
of non-MPC client as fallback to TCP"). The new condition added by
this commit was then not expected, and was in fact at the wrong place
in v6.6: in case of issue, the problem would not have been reported
correctly. ]
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 36a1ca01f0 ]
The patch mentioned in the `Fixes` tag removed the explicit assignment
of tx_info->xdpf to NULL with the justification that there's no need
to set tx_info->xdpf to NULL and tx_info->num_of_bufs to 0 in case
of a mapping error. Both values won't be used once the mapping function
returns an error, and their values would be overridden by the next
transmitted packet.
While both values do indeed get overridden in the next transmission
call, the value of tx_info->xdpf is also used to check whether a TX
descriptor's transmission has been completed (i.e. a completion for it
was polled).
An example scenario:
1. Mapping failed, tx_info->xdpf wasn't set to NULL
2. A VF reset occurred leading to IO resource destruction and
a call to ena_free_tx_bufs() function
3. Although the descriptor whose mapping failed was freed by the
transmission function, it still passes the check
if (!tx_info->skb)
(skb and xdp_frame are in a union)
4. The xdp_frame associated with the descriptor is freed twice
This patch returns the assignment of NULL to tx_info->xdpf to make the
cleaning function knows that the descriptor is already freed.
Fixes: 504fd6a539 ("net: ena: fix DMA mapping function issues in XDP")
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David Arinzon <darinzon@amazon.com>
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 911a8c9601 ]
When an XDP program is loaded the existing channels in the driver split
into two halves:
- The first half of the channels contain RX and TX rings, these queues
are used for receiving traffic and sending packets originating from
kernel.
- The second half of the channels contain only a TX ring. These queues
are used for sending packets that were redirected using XDP_TX
or XDP_REDIRECT.
Referring to the queues in the second half of the channels as "xdp_ring"
can be confusing and may give the impression that ENA has the capability
to generate an additional special queue.
This patch ensures that the xdp_ring field is exclusively used to
describe the XDP TX queue that a specific RX queue needs to utilize when
forwarding packets with XDP TX and XDP REDIRECT, preserving the
integrity of the xdp_ring field in ena_ring.
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David Arinzon <darinzon@amazon.com>
Link: https://lore.kernel.org/r/20240101190855.18739-6-darinzon@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 36a1ca01f0 ("net: ena: Set tx_info->xdpf value to NULL")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39a044f4dc ]
This change will enable the ability to use ena_xmit_common()
in functions that don't have a net_device pointer.
While it can be retrieved by dereferencing
ena_adapter (adapter->netdev), there's no reason to do it in
fast path code where this pointer is only needed for
debug prints.
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David Arinzon <darinzon@amazon.com>
Link: https://lore.kernel.org/r/20240101190855.18739-3-darinzon@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 36a1ca01f0 ("net: ena: Set tx_info->xdpf value to NULL")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d000574d02 ]
XDP system has a very large footprint in the driver's overall code.
makes the whole driver's code much harder to read.
Moving XDP code to dedicated files.
This patch doesn't make any changes to the code itself and only
cut-pastes the code into ena_xdp.c and ena_xdp.h files so the change
is purely cosmetic.
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David Arinzon <darinzon@amazon.com>
Link: https://lore.kernel.org/r/20240101190855.18739-2-darinzon@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 36a1ca01f0 ("net: ena: Set tx_info->xdpf value to NULL")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf02d9fe00 ]
ENA has two types of TX queues:
- queues which only process TX packets arriving from the network stack
- queues which only process TX packets forwarded to it by XDP_REDIRECT
or XDP_TX instructions
The ena_free_tx_bufs() cycles through all descriptors in a TX queue
and unmaps + frees every descriptor that hasn't been acknowledged yet
by the device (uncompleted TX transactions).
The function assumes that the processed TX queue is necessarily from
the first category listed above and ends up using napi_consume_skb()
for descriptors belonging to an XDP specific queue.
This patch solves a bug in which, in case of a VF reset, the
descriptors aren't freed correctly, leading to crashes.
Fixes: 548c4940b9 ("net: ena: Implement XDP_TX action")
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David Arinzon <darinzon@amazon.com>
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f7e4171806 ]
Missing IO completions check is called every second (HZ jiffies).
This commit fixes several issues with this check:
1. Duplicate queues check:
Max of 4 queues are scanned on each check due to monitor budget.
Once reaching the budget, this check exits under the assumption that
the next check will continue to scan the remainder of the queues,
but in practice, next check will first scan the last already scanned
queue which is not necessary and may cause the full queue scan to
last a couple of seconds longer.
The fix is to start every check with the next queue to scan.
For example, on 8 IO queues:
Bug: [0,1,2,3], [3,4,5,6], [6,7]
Fix: [0,1,2,3], [4,5,6,7]
2. Unbalanced queues check:
In case the number of active IO queues is not a multiple of budget,
there will be checks which don't utilize the full budget
because the full scan exits when reaching the last queue id.
The fix is to run every TX completion check with exact queue budget
regardless of the queue id.
For example, on 7 IO queues:
Bug: [0,1,2,3], [4,5,6], [0,1,2,3]
Fix: [0,1,2,3], [4,5,6,0], [1,2,3,4]
The budget may be lowered in case the number of IO queues is less
than the budget (4) to make sure there are no duplicate queues on
the same check.
For example, on 3 IO queues:
Bug: [0,1,2,0], [1,2,0,1]
Fix: [0,1,2], [0,1,2]
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Amit Bernstein <amitbern@amazon.com>
Signed-off-by: David Arinzon <darinzon@amazon.com>
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 713a85195a ]
Small unsigned types are promoted to larger signed types in
the case of multiplication, the result of which may overflow.
In case the result of such a multiplication has its MSB
turned on, it will be sign extended with '1's.
This changes the multiplication result.
Code example of the phenomenon:
-------------------------------
u16 x, y;
size_t z1, z2;
x = y = 0xffff;
printk("x=%x y=%x\n",x,y);
z1 = x*y;
z2 = (size_t)x*y;
printk("z1=%lx z2=%lx\n", z1, z2);
Output:
-------
x=ffff y=ffff
z1=fffffffffffe0001 z2=fffe0001
The expected result of ffff*ffff is fffe0001, and without the
explicit casting to avoid the unwanted sign extension we got
fffffffffffe0001.
This commit adds an explicit casting to avoid the sign extension
issue.
Fixes: 689b2bdaaa ("net: ena: add functions for handling Low Latency Queues in ena_com")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David Arinzon <darinzon@amazon.com>
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 47d8ac011f ]
Garbage collector does not take into account the risk of embryo getting
enqueued during the garbage collection. If such embryo has a peer that
carries SCM_RIGHTS, two consecutive passes of scan_children() may see a
different set of children. Leading to an incorrectly elevated inflight
count, and then a dangling pointer within the gc_inflight_list.
sockets are AF_UNIX/SOCK_STREAM
S is an unconnected socket
L is a listening in-flight socket bound to addr, not in fdtable
V's fd will be passed via sendmsg(), gets inflight count bumped
connect(S, addr) sendmsg(S, [V]); close(V) __unix_gc()
---------------- ------------------------- -----------
NS = unix_create1()
skb1 = sock_wmalloc(NS)
L = unix_find_other(addr)
unix_state_lock(L)
unix_peer(S) = NS
// V count=1 inflight=0
NS = unix_peer(S)
skb2 = sock_alloc()
skb_queue_tail(NS, skb2[V])
// V became in-flight
// V count=2 inflight=1
close(V)
// V count=1 inflight=1
// GC candidate condition met
for u in gc_inflight_list:
if (total_refs == inflight_refs)
add u to gc_candidates
// gc_candidates={L, V}
for u in gc_candidates:
scan_children(u, dec_inflight)
// embryo (skb1) was not
// reachable from L yet, so V's
// inflight remains unchanged
__skb_queue_tail(L, skb1)
unix_state_unlock(L)
for u in gc_candidates:
if (u.inflight)
scan_children(u, inc_inflight_move_tail)
// V count=1 inflight=2 (!)
If there is a GC-candidate listening socket, lock/unlock its state. This
makes GC wait until the end of any ongoing connect() to that socket. After
flipping the lock, a possibly SCM-laden embryo is already enqueued. And if
there is another embryo coming, it can not possibly carry SCM_RIGHTS. At
this point, unix_inflight() can not happen because unix_gc_lock is already
taken. Inflight graph remains unaffected.
Fixes: 1fd05ba5a2 ("[AF_UNIX]: Rewrite garbage collector, fixes race.")
Signed-off-by: Michal Luczaj <mhal@rbox.co>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20240409201047.1032217-1-mhal@rbox.co
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 17c5601132 ]
In Clause 5 of IEEE Std 802-2014, two sublayers of the data link layer
(DLL) of the Open Systems Interconnection basic reference model (OSI/RM)
are described; the medium access control (MAC) and logical link control
(LLC) sublayers. The MAC sublayer is the one facing the physical layer.
In 8.2 of IEEE Std 802.1Q-2022, the Bridge architecture is described. A
Bridge component comprises a MAC Relay Entity for interconnecting the Ports
of the Bridge, at least two Ports, and higher layer entities with at least
a Spanning Tree Protocol Entity included.
Each Bridge Port also functions as an end station and shall provide the MAC
Service to an LLC Entity. Each instance of the MAC Service is provided to a
distinct LLC Entity that supports protocol identification, multiplexing,
and demultiplexing, for protocol data unit (PDU) transmission and reception
by one or more higher layer entities.
It is described in 8.13.9 of IEEE Std 802.1Q-2022 that in a Bridge, the LLC
Entity associated with each Bridge Port is modeled as being directly
connected to the attached Local Area Network (LAN).
On the switch with CPU port architecture, CPU port functions as Management
Port, and the Management Port functionality is provided by software which
functions as an end station. Software is connected to an IEEE 802 LAN that
is wholly contained within the system that incorporates the Bridge.
Software provides access to the LLC Entity associated with each Bridge Port
by the value of the source port field on the special tag on the frame
received by software.
We call frames that carry control information to determine the active
topology and current extent of each Virtual Local Area Network (VLAN),
i.e., spanning tree or Shortest Path Bridging (SPB) and Multiple VLAN
Registration Protocol Data Units (MVRPDUs), and frames from other link
constrained protocols, such as Extensible Authentication Protocol over LAN
(EAPOL) and Link Layer Discovery Protocol (LLDP), link-local frames. They
are not forwarded by a Bridge. Permanently configured entries in the
filtering database (FDB) ensure that such frames are discarded by the
Forwarding Process. In 8.6.3 of IEEE Std 802.1Q-2022, this is described in
detail:
Each of the reserved MAC addresses specified in Table 8-1
(01-80-C2-00-00-[00,01,02,03,04,05,06,07,08,09,0A,0B,0C,0D,0E,0F]) shall be
permanently configured in the FDB in C-VLAN components and ERs.
Each of the reserved MAC addresses specified in Table 8-2
(01-80-C2-00-00-[01,02,03,04,05,06,07,08,09,0A,0E]) shall be permanently
configured in the FDB in S-VLAN components.
Each of the reserved MAC addresses specified in Table 8-3
(01-80-C2-00-00-[01,02,04,0E]) shall be permanently configured in the FDB
in TPMR components.
The FDB entries for reserved MAC addresses shall specify filtering for all
Bridge Ports and all VIDs. Management shall not provide the capability to
modify or remove entries for reserved MAC addresses.
The addresses in Table 8-1, Table 8-2, and Table 8-3 determine the scope of
propagation of PDUs within a Bridged Network, as follows:
The Nearest Bridge group address (01-80-C2-00-00-0E) is an address that
no conformant Two-Port MAC Relay (TPMR) component, Service VLAN (S-VLAN)
component, Customer VLAN (C-VLAN) component, or MAC Bridge can forward.
PDUs transmitted using this destination address, or any other addresses
that appear in Table 8-1, Table 8-2, and Table 8-3
(01-80-C2-00-00-[00,01,02,03,04,05,06,07,08,09,0A,0B,0C,0D,0E,0F]), can
therefore travel no further than those stations that can be reached via a
single individual LAN from the originating station.
The Nearest non-TPMR Bridge group address (01-80-C2-00-00-03), is an
address that no conformant S-VLAN component, C-VLAN component, or MAC
Bridge can forward; however, this address is relayed by a TPMR component.
PDUs using this destination address, or any of the other addresses that
appear in both Table 8-1 and Table 8-2 but not in Table 8-3
(01-80-C2-00-00-[00,03,05,06,07,08,09,0A,0B,0C,0D,0F]), will be relayed
by any TPMRs but will propagate no further than the nearest S-VLAN
component, C-VLAN component, or MAC Bridge.
The Nearest Customer Bridge group address (01-80-C2-00-00-00) is an
address that no conformant C-VLAN component, MAC Bridge can forward;
however, it is relayed by TPMR components and S-VLAN components. PDUs
using this destination address, or any of the other addresses that appear
in Table 8-1 but not in either Table 8-2 or Table 8-3
(01-80-C2-00-00-[00,0B,0C,0D,0F]), will be relayed by TPMR components and
S-VLAN components but will propagate no further than the nearest C-VLAN
component or MAC Bridge.
Because the LLC Entity associated with each Bridge Port is provided via CPU
port, we must not filter these frames but forward them to CPU port.
In a Bridge, the transmission Port is majorly decided by ingress and egress
rules, FDB, and spanning tree Port State functions of the Forwarding
Process. For link-local frames, only CPU port should be designated as
destination port in the FDB, and the other functions of the Forwarding
Process must not interfere with the decision of the transmission Port. We
call this process trapping frames to CPU port.
Therefore, on the switch with CPU port architecture, link-local frames must
be trapped to CPU port, and certain link-local frames received by a Port of
a Bridge comprising a TPMR component or an S-VLAN component must be
excluded from it.
A Bridge of the switch with CPU port architecture cannot comprise a
Two-Port MAC Relay (TPMR) component as a TPMR component supports only a
subset of the functionality of a MAC Bridge. A Bridge comprising two Ports
(Management Port doesn't count) of this architecture will either function
as a standard MAC Bridge or a standard VLAN Bridge.
Therefore, a Bridge of this architecture can only comprise S-VLAN
components, C-VLAN components, or MAC Bridge components. Since there's no
TPMR component, we don't need to relay PDUs using the destination addresses
specified on the Nearest non-TPMR section, and the proportion of the
Nearest Customer Bridge section where they must be relayed by TPMR
components.
One option to trap link-local frames to CPU port is to add static FDB
entries with CPU port designated as destination port. However, because that
Independent VLAN Learning (IVL) is being used on every VID, each entry only
applies to a single VLAN Identifier (VID). For a Bridge comprising a MAC
Bridge component or a C-VLAN component, there would have to be 16 times
4096 entries. This switch intellectual property can only hold a maximum of
2048 entries. Using this option, there also isn't a mechanism to prevent
link-local frames from being discarded when the spanning tree Port State of
the reception Port is discarding.
The remaining option is to utilise the BPC, RGAC1, RGAC2, RGAC3, and RGAC4
registers. Whilst this applies to every VID, it doesn't contain all of the
reserved MAC addresses without affecting the remaining Standard Group MAC
Addresses. The REV_UN frame tag utilised using the RGAC4 register covers
the remaining 01-80-C2-00-00-[04,05,06,07,08,09,0A,0B,0C,0D,0F] destination
addresses. It also includes the 01-80-C2-00-00-22 to 01-80-C2-00-00-FF
destination addresses which may be relayed by MAC Bridges or VLAN Bridges.
The latter option provides better but not complete conformance.
This switch intellectual property also does not provide a mechanism to trap
link-local frames with specific destination addresses to CPU port by
Bridge, to conform to the filtering rules for the distinct Bridge
components.
Therefore, regardless of the type of the Bridge component, link-local
frames with these destination addresses will be trapped to CPU port:
01-80-C2-00-00-[00,01,02,03,0E]
In a Bridge comprising a MAC Bridge component or a C-VLAN component:
Link-local frames with these destination addresses won't be trapped to
CPU port which won't conform to IEEE Std 802.1Q-2022:
01-80-C2-00-00-[04,05,06,07,08,09,0A,0B,0C,0D,0F]
In a Bridge comprising an S-VLAN component:
Link-local frames with these destination addresses will be trapped to CPU
port which won't conform to IEEE Std 802.1Q-2022:
01-80-C2-00-00-00
Link-local frames with these destination addresses won't be trapped to
CPU port which won't conform to IEEE Std 802.1Q-2022:
01-80-C2-00-00-[04,05,06,07,08,09,0A]
Currently on this switch intellectual property, if the spanning tree Port
State of the reception Port is discarding, link-local frames will be
discarded.
To trap link-local frames regardless of the spanning tree Port State, make
the switch regard them as Bridge Protocol Data Units (BPDUs). This switch
intellectual property only lets the frames regarded as BPDUs bypass the
spanning tree Port State function of the Forwarding Process.
With this change, the only remaining interference is the ingress rules.
When the reception Port has no PVID assigned on software, VLAN-untagged
frames won't be allowed in. There doesn't seem to be a mechanism on the
switch intellectual property to have link-local frames bypass this function
of the Forwarding Process.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20240409-b4-for-net-mt7530-fix-link-local-when-stp-discarding-v2-1-07b1150164ac@arinc9.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f436f1869 ]
When creating a new HTB class while the interface is down,
the variable that follows the number of QoS SQs (htb_max_qos_sqs)
may not be consistent with the number of HTB classes.
Previously, we compared these two values to ensure that
the node_qid is lower than the number of QoS SQs, and we
allocated stats for that SQ when they are equal.
Change the check to compare the node_qid with the current
number of leaf nodes and fix the checking conditions to
ensure allocation of stats_list and stats for each node.
Fixes: 214baf2287 ("net/mlx5e: Support HTB offload")
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240409190820.227554-9-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9eca93f4d5 ]
struct mlx5_pkt_reformat contains a naked union of a u32 id and a
dr_action pointer which is used when the action is SW-managed (when
pkt_reformat.owner is set to MLX5_FLOW_RESOURCE_OWNER_SW). Using id
directly in that case is incorrect, as it maps to the least significant
32 bits of the 64-bit pointer in mlx5_fs_dr_action and not to the pkt
reformat id allocated in firmware.
For the purpose of comparing whether two rules are identical,
interpreting the least significant 32 bits of the mlx5_fs_dr_action
pointer as an id mostly works... until it breaks horribly and produces
the outcome described in [1].
This patch fixes mlx5_flow_dests_cmp to correctly compare ids using
mlx5_fs_dr_action_get_pkt_reformat_id for the SW-managed rules.
Link: https://lore.kernel.org/netdev/ea5264d6-6b55-4449-a602-214c6f509c1e@163.com/T/#u [1]
Fixes: 6a48faeeca ("net/mlx5: Add direct rule fs_cmd implementation")
Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240409190820.227554-6-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c6782ad49 ]
Previously, add_rule_fg would only add newly created rules from the
handle into the tree when they had a refcount of 1. On the other hand,
create_flow_handle tries hard to find and reference already existing
identical rules instead of creating new ones.
These two behaviors can result in a situation where create_flow_handle
1) creates a new rule and references it, then
2) in a subsequent step during the same handle creation references it
again,
resulting in a rule with a refcount of 2 that is not linked into the
tree, will have a NULL parent and root and will result in a crash when
the flow group is deleted because del_sw_hw_rule, invoked on rule
deletion, assumes node->parent is != NULL.
This happened in the wild, due to another bug related to incorrect
handling of duplicate pkt_reformat ids, which lead to the code in
create_flow_handle incorrectly referencing a just-added rule in the same
flow handle, resulting in the problem described above. Full details are
at [1].
This patch changes add_rule_fg to add new rules without parents into
the tree, properly initializing them and avoiding the crash. This makes
it more consistent with how rules are added to an FTE in
create_flow_handle.
Fixes: 74491de937 ("net/mlx5: Add multi dest support")
Link: https://lore.kernel.org/netdev/ea5264d6-6b55-4449-a602-214c6f509c1e@163.com/T/#u [1]
Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240409190820.227554-5-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c6e77aa9dd ]
In case device is having a non fatal FW error during probe, the
driver will report the error to user via devlink. This will trigger
a WARN_ON, since mlx5 is calling devlink_register() last.
In order to avoid the WARN_ON[1], change mlx5 to invoke devl_register()
first under devlink lock.
[1]
WARNING: CPU: 5 PID: 227 at net/devlink/health.c:483 devlink_recover_notify.constprop.0+0xb8/0xc0
CPU: 5 PID: 227 Comm: kworker/u16:3 Not tainted 6.4.0-rc5_for_upstream_min_debug_2023_06_12_12_38 #1
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
Workqueue: mlx5_health0000:08:00.0 mlx5_fw_reporter_err_work [mlx5_core]
RIP: 0010:devlink_recover_notify.constprop.0+0xb8/0xc0
Call Trace:
<TASK>
? __warn+0x79/0x120
? devlink_recover_notify.constprop.0+0xb8/0xc0
? report_bug+0x17c/0x190
? handle_bug+0x3c/0x60
? exc_invalid_op+0x14/0x70
? asm_exc_invalid_op+0x16/0x20
? devlink_recover_notify.constprop.0+0xb8/0xc0
devlink_health_report+0x4a/0x1c0
mlx5_fw_reporter_err_work+0xa4/0xd0 [mlx5_core]
process_one_work+0x1bb/0x3c0
? process_one_work+0x3c0/0x3c0
worker_thread+0x4d/0x3c0
? process_one_work+0x3c0/0x3c0
kthread+0xc6/0xf0
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x1f/0x30
</TASK>
Fixes: cf53021740 ("devlink: Notify users when objects are accessible")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240409190820.227554-3-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 137cef6d55 ]
When PF/VF teardown is called the driver sets the flag
MLX5_BREAK_FW_WAIT to stop waiting for FW loading and initializing. Same
should be applied to SF driver teardown to cut waiting time. On
mlx5_sf_dev_remove() set the flag before draining health WQ as recovery
flow may also wait for FW reloading while it is not relevant anymore.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Stable-dep-of: c6e77aa9dd ("net/mlx5: Register devlink first under devlink lock")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65acf6e050 ]
In my recent commit, I missed that do_replace() handlers
use copy_from_sockptr() (which I fixed), followed
by unsafe copy_from_sockptr_offset() calls.
In all functions, we can perform the @optlen validation
before even calling xt_alloc_table_info() with the following
check:
if ((u64)optlen < (u64)tmp.size + sizeof(tmp))
return -EINVAL;
Fixes: 0c83842df4 ("netfilter: validate user input for expected length")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Pablo Neira Ayuso <pablo@netfilter.org>
Link: https://lore.kernel.org/r/20240409120741.3538135-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 600b0bbe73 ]
The bit is set and tested inside mgmt_device_connected(), therefore we
must not set it just outside the function.
Fixes: eeda1bf97b ("Bluetooth: hci_event: Fix not indicating new connection for BIG Sync")
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Manish Mandlik <mmandlik@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51eda36d33 ]
syzbot reported sco_sock_setsockopt() is copying data without
checking user input length.
BUG: KASAN: slab-out-of-bounds in copy_from_sockptr_offset
include/linux/sockptr.h:49 [inline]
BUG: KASAN: slab-out-of-bounds in copy_from_sockptr
include/linux/sockptr.h:55 [inline]
BUG: KASAN: slab-out-of-bounds in sco_sock_setsockopt+0xc0b/0xf90
net/bluetooth/sco.c:893
Read of size 4 at addr ffff88805f7b15a3 by task syz-executor.5/12578
Fixes: ad10b1a487 ("Bluetooth: Add Bluetooth socket voice option")
Fixes: b96e9c671b ("Bluetooth: Add BT_DEFER_SETUP option to sco socket")
Fixes: 00398e1d51 ("Bluetooth: Add support for BT_PKT_STATUS CMSG data for SCO connections")
Fixes: f6873401a6 ("Bluetooth: Allow setting of codec for HFP offload use case")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 53cb4197e6 ]
Coded PHY recommended intervals are 3 time bigger than the 1M PHY so
this aligns with that by multiplying by 3 the values given to 1M PHY
since the code already used recommended values for that.
Fixes: 288c90224e ("Bluetooth: Enable all supported LE PHY by default")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 22cbf4f84c ]
This used the hci_conn QoS to determine which PHY to scan when creating
a PA Sync.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Stable-dep-of: 53cb4197e6 ("Bluetooth: hci_sync: Fix using the same interval and window for Coded PHY")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b37cab587a ]
Consider certain values (0x00) as unset and load proper default if
an application has not set them properly.
Fixes: 0fe8c8d071 ("Bluetooth: Split bt_iso_qos into dedicated structures")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 42ed95de82 ]
This aligns broadcast sync_timeout with existing connection timeouts
which are 20 seconds long.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Stable-dep-of: b37cab587a ("Bluetooth: ISO: Don't reject BT_ISO_QOS if parameters are unset")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf1b7201df ]
The log_martians variable is only used in an #ifdef, causing a 'make W=1'
warning with gcc:
net/ipv4/route.c: In function 'ip_rt_send_redirect':
net/ipv4/route.c:880:13: error: variable 'log_martians' set but not used [-Werror=unused-but-set-variable]
Change the #ifdef to an equivalent IS_ENABLED() to let the compiler
see where the variable is used.
Fixes: 30038fc61a ("net: ip_rt_send_redirect() optimization")
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240408074219.3030256-2-arnd@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit faf2300618 ]
NIX SQ mode and link backpressure configuration is required for
all platforms. But in current driver this code is wrongly placed
under specific platform check. This patch fixes the issue by
moving the code out of platform check.
Fixes: 5d9b976d44 ("octeontx2-af: Support fixed transmit scheduler topology")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Link: https://lore.kernel.org/r/20240408063643.26288-1-gakula@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b46f4eaa4f ]
syzkaller started to report deadlock of unix_gc_lock after commit
4090fa373f ("af_unix: Replace garbage collection algorithm."), but
it just uncovers the bug that has been there since commit 314001f0bf
("af_unix: Add OOB support").
The repro basically does the following.
from socket import *
from array import array
c1, c2 = socketpair(AF_UNIX, SOCK_STREAM)
c1.sendmsg([b'a'], [(SOL_SOCKET, SCM_RIGHTS, array("i", [c2.fileno()]))], MSG_OOB)
c2.recv(1) # blocked as no normal data in recv queue
c2.close() # done async and unblock recv()
c1.close() # done async and trigger GC
A socket sends its file descriptor to itself as OOB data and tries to
receive normal data, but finally recv() fails due to async close().
The problem here is wrong handling of OOB skb in manage_oob(). When
recvmsg() is called without MSG_OOB, manage_oob() is called to check
if the peeked skb is OOB skb. In such a case, manage_oob() pops it
out of the receive queue but does not clear unix_sock(sk)->oob_skb.
This is wrong in terms of uAPI.
Let's say we send "hello" with MSG_OOB, and "world" without MSG_OOB.
The 'o' is handled as OOB data. When recv() is called twice without
MSG_OOB, the OOB data should be lost.
>>> from socket import *
>>> c1, c2 = socketpair(AF_UNIX, SOCK_STREAM, 0)
>>> c1.send(b'hello', MSG_OOB) # 'o' is OOB data
5
>>> c1.send(b'world')
5
>>> c2.recv(5) # OOB data is not received
b'hell'
>>> c2.recv(5) # OOB date is skipped
b'world'
>>> c2.recv(5, MSG_OOB) # This should return an error
b'o'
In the same situation, TCP actually returns -EINVAL for the last
recv().
Also, if we do not clear unix_sk(sk)->oob_skb, unix_poll() always set
EPOLLPRI even though the data has passed through by previous recv().
To avoid these issues, we must clear unix_sk(sk)->oob_skb when dequeuing
it from recv queue.
The reason why the old GC did not trigger the deadlock is because the
old GC relied on the receive queue to detect the loop.
When it is triggered, the socket with OOB data is marked as GC candidate
because file refcount == inflight count (1). However, after traversing
all inflight sockets, the socket still has a positive inflight count (1),
thus the socket is excluded from candidates. Then, the old GC lose the
chance to garbage-collect the socket.
With the old GC, the repro continues to create true garbage that will
never be freed nor detected by kmemleak as it's linked to the global
inflight list. That's why we couldn't even notice the issue.
Fixes: 314001f0bf ("af_unix: Add OOB support")
Reported-by: syzbot+7f7f201cc2668a8fd169@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=7f7f201cc2668a8fd169
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240405221057.2406-1-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be0384bf59 ]
The ks8851_irq() thread may call ks8851_rx_pkts() in case there are
any packets in the MAC FIFO, which calls netif_rx(). This netif_rx()
implementation is guarded by local_bh_disable() and local_bh_enable().
The local_bh_enable() may call do_softirq() to run softirqs in case
any are pending. One of the softirqs is net_rx_action, which ultimately
reaches the driver .start_xmit callback. If that happens, the system
hangs. The entire call chain is below:
ks8851_start_xmit_par from netdev_start_xmit
netdev_start_xmit from dev_hard_start_xmit
dev_hard_start_xmit from sch_direct_xmit
sch_direct_xmit from __dev_queue_xmit
__dev_queue_xmit from __neigh_update
__neigh_update from neigh_update
neigh_update from arp_process.constprop.0
arp_process.constprop.0 from __netif_receive_skb_one_core
__netif_receive_skb_one_core from process_backlog
process_backlog from __napi_poll.constprop.0
__napi_poll.constprop.0 from net_rx_action
net_rx_action from __do_softirq
__do_softirq from call_with_stack
call_with_stack from do_softirq
do_softirq from __local_bh_enable_ip
__local_bh_enable_ip from netif_rx
netif_rx from ks8851_irq
ks8851_irq from irq_thread_fn
irq_thread_fn from irq_thread
irq_thread from kthread
kthread from ret_from_fork
The hang happens because ks8851_irq() first locks a spinlock in
ks8851_par.c ks8851_lock_par() spin_lock_irqsave(&ksp->lock, ...)
and with that spinlock locked, calls netif_rx(). Once the execution
reaches ks8851_start_xmit_par(), it calls ks8851_lock_par() again
which attempts to claim the already locked spinlock again, and the
hang happens.
Move the do_softirq() call outside of the spinlock protected section
of ks8851_irq() by disabling BHs around the entire spinlock protected
section of ks8851_irq() handler. Place local_bh_enable() outside of
the spinlock protected section, so that it can trigger do_softirq()
without the ks8851_par.c ks8851_lock_par() spinlock being held, and
safely call ks8851_start_xmit_par() without attempting to lock the
already locked spinlock.
Since ks8851_irq() is protected by local_bh_disable()/local_bh_enable()
now, replace netif_rx() with __netif_rx() which is not duplicating the
local_bh_disable()/local_bh_enable() calls.
Fixes: 797047f875 ("net: ks8851: Implement Parallel bus operations")
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20240405203204.82062-2-marex@denx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f96f700449 ]
Both ks8851_rx_skb_par() and ks8851_rx_skb_spi() call netif_rx(skb),
inline the netif_rx(skb) call directly into ks8851_common.c and drop
the .rx_skb callback and ks8851_rx_skb() wrapper. This removes one
indirect call from the driver, no functional change otherwise.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20240405203204.82062-1-marex@denx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: be0384bf59 ("net: ks8851: Handle softirqs at the end of IRQ thread to fix hang")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit faa12ca245 ]
It is possible that during error recovery and firmware reset,
there is a pending TX PTP packet waiting for the timestamp.
We need to reset this condition so that after recovery, the
tx_avail count for PTP is reset back to the initial value.
Otherwise, we may not accept any PTP TX timestamps after
recovery.
Fixes: 118612d519 ("bnxt_en: Add PTP clock APIs, ioctls, and ethtool methods")
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b5ea7d33ba ]
Since runtime MSIXs vector allocation/free has been removed,
the L2 driver needs to repopulate the MSIX entries for the
ulp client as the irq table may change during the recovery
process.
Fixes: 3034322113 ("bnxt_en: Remove runtime interrupt vector allocation")
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ac10c7d72 ]
If ulp = kzalloc() fails, the allocated edev will leak because it is
not properly assigned and the cleanup path will not be able to free it.
Fix it by assigning it properly immediately after allocation.
Fixes: 3034322113 ("bnxt_en: Remove runtime interrupt vector allocation")
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58effa3476 ]
Since [1], dma_alloc_coherent() does not accept requests for GFP_COMP
anymore, even on archs that may be able to fulfill this. Functionality that
relied on the receive buffer being a compound page broke at that point:
The SMC-D protocol, that utilizes the ism device driver, passes receive
buffers to the splice processor in a struct splice_pipe_desc with a
single entry list of struct pages. As the buffer is no longer a compound
page, the splice processor now rejects requests to handle more than a
page worth of data.
Replace dma_alloc_coherent() and allocate a buffer with folio_alloc and
create a DMA map for it with dma_map_page(). Since only receive buffers
on ISM devices use DMA, qualify the mapping as FROM_DEVICE.
Since ISM devices are available on arch s390, only and on that arch all
DMA is coherent, there is no need to introduce and export some kind of
dma_sync_to_cpu() method to be called by the SMC-D protocol layer.
Analogously, replace dma_free_coherent by a two step dma_unmap_page,
then folio_put to free the receive buffer.
[1] https://lore.kernel.org/all/20221113163535.884299-1-hch@lst.de/
Fixes: c08004eede ("s390/ism: don't pass bogus GFP_ flags to dma_alloc_coherent")
Signed-off-by: Gerd Bayer <gbayer@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d8a6213d70 ]
syzbot is able to trigger an uninit-value in geneve_xmit() [1]
Problem : While most ip tunnel helpers (like ip_tunnel_get_dsfield())
uses skb_protocol(skb, true), pskb_inet_may_pull() is only using
skb->protocol.
If anything else than ETH_P_IPV6 or ETH_P_IP is found in skb->protocol,
pskb_inet_may_pull() does nothing at all.
If a vlan tag was provided by the caller (af_packet in the syzbot case),
the network header might not point to the correct location, and skb
linear part could be smaller than expected.
Add skb_vlan_inet_prepare() to perform a complete mac validation.
Use this in geneve for the moment, I suspect we need to adopt this
more broadly.
v4 - Jakub reported v3 broke l2_tos_ttl_inherit.sh selftest
- Only call __vlan_get_protocol() for vlan types.
Link: https://lore.kernel.org/netdev/20240404100035.3270a7d5@kernel.org/
v2,v3 - Addressed Sabrina comments on v1 and v2
Link: https://lore.kernel.org/netdev/Zg1l9L2BNoZWZDZG@hog/
[1]
BUG: KMSAN: uninit-value in geneve_xmit_skb drivers/net/geneve.c:910 [inline]
BUG: KMSAN: uninit-value in geneve_xmit+0x302d/0x5420 drivers/net/geneve.c:1030
geneve_xmit_skb drivers/net/geneve.c:910 [inline]
geneve_xmit+0x302d/0x5420 drivers/net/geneve.c:1030
__netdev_start_xmit include/linux/netdevice.h:4903 [inline]
netdev_start_xmit include/linux/netdevice.h:4917 [inline]
xmit_one net/core/dev.c:3531 [inline]
dev_hard_start_xmit+0x247/0xa20 net/core/dev.c:3547
__dev_queue_xmit+0x348d/0x52c0 net/core/dev.c:4335
dev_queue_xmit include/linux/netdevice.h:3091 [inline]
packet_xmit+0x9c/0x6c0 net/packet/af_packet.c:276
packet_snd net/packet/af_packet.c:3081 [inline]
packet_sendmsg+0x8bb0/0x9ef0 net/packet/af_packet.c:3113
sock_sendmsg_nosec net/socket.c:730 [inline]
__sock_sendmsg+0x30f/0x380 net/socket.c:745
__sys_sendto+0x685/0x830 net/socket.c:2191
__do_sys_sendto net/socket.c:2203 [inline]
__se_sys_sendto net/socket.c:2199 [inline]
__x64_sys_sendto+0x125/0x1d0 net/socket.c:2199
do_syscall_64+0xd5/0x1f0
entry_SYSCALL_64_after_hwframe+0x6d/0x75
Uninit was created at:
slab_post_alloc_hook mm/slub.c:3804 [inline]
slab_alloc_node mm/slub.c:3845 [inline]
kmem_cache_alloc_node+0x613/0xc50 mm/slub.c:3888
kmalloc_reserve+0x13d/0x4a0 net/core/skbuff.c:577
__alloc_skb+0x35b/0x7a0 net/core/skbuff.c:668
alloc_skb include/linux/skbuff.h:1318 [inline]
alloc_skb_with_frags+0xc8/0xbf0 net/core/skbuff.c:6504
sock_alloc_send_pskb+0xa81/0xbf0 net/core/sock.c:2795
packet_alloc_skb net/packet/af_packet.c:2930 [inline]
packet_snd net/packet/af_packet.c:3024 [inline]
packet_sendmsg+0x722d/0x9ef0 net/packet/af_packet.c:3113
sock_sendmsg_nosec net/socket.c:730 [inline]
__sock_sendmsg+0x30f/0x380 net/socket.c:745
__sys_sendto+0x685/0x830 net/socket.c:2191
__do_sys_sendto net/socket.c:2203 [inline]
__se_sys_sendto net/socket.c:2199 [inline]
__x64_sys_sendto+0x125/0x1d0 net/socket.c:2199
do_syscall_64+0xd5/0x1f0
entry_SYSCALL_64_after_hwframe+0x6d/0x75
CPU: 0 PID: 5033 Comm: syz-executor346 Not tainted 6.9.0-rc1-syzkaller-00005-g928a87efa423 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 02/29/2024
Fixes: d13f048dd4 ("net: geneve: modify IP header check in geneve6_xmit_skb and geneve_xmit_skb")
Reported-by: syzbot+9ee20ec1de7b3168db09@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/netdev/000000000000d19c3a06152f9ee4@google.com/
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Phillip Potter <phil@philpotter.co.uk>
Cc: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Phillip Potter <phil@philpotter.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b8ace0803 ]
Multiple gendisk instances can allocated/added for single request queue
in case of disk rebind. blkg may still stay in q->blkg_list when calling
blkcg_init_disk() for rebind, then q->blkg_list becomes corrupted.
Fix the list corruption issue by:
- add blkg_init_queue() to initialize q->blkg_list & q->blkcg_mutex only
- move calling blkg_init_queue() into blk_alloc_queue()
The list corruption should be started since commit f1c006f1c6 ("blk-cgroup:
synchronize pd_free_fn() from blkg_free_workfn() and blkcg_deactivate_policy()")
which delays removing blkg from q->blkg_list into blkg_free_workfn().
Fixes: f1c006f1c6 ("blk-cgroup: synchronize pd_free_fn() from blkg_free_workfn() and blkcg_deactivate_policy()")
Fixes: 1059699f87 ("block: move blkcg initialization/destroy into disk allocation/release handler")
Cc: Yu Kuai <yukuai3@huawei.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Link: https://lore.kernel.org/r/20240407125910.4053377-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bccb798e07 ]
Inorder to support shaping and scheduling, Upon class creation
Netdev driver allocates trasmit schedulers.
The previous patch which added support for Round robin scheduling has
a bug due to which driver is not freeing transmit schedulers post
class deletion.
This patch fixes the same.
Fixes: 47a9656f16 ("octeontx2-pf: htb offload support for Round Robin scheduling")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 237f3cf13b ]
syzbot reported an illegal copy in xsk_setsockopt() [1]
Make sure to validate setsockopt() @optlen parameter.
[1]
BUG: KASAN: slab-out-of-bounds in copy_from_sockptr_offset include/linux/sockptr.h:49 [inline]
BUG: KASAN: slab-out-of-bounds in copy_from_sockptr include/linux/sockptr.h:55 [inline]
BUG: KASAN: slab-out-of-bounds in xsk_setsockopt+0x909/0xa40 net/xdp/xsk.c:1420
Read of size 4 at addr ffff888028c6cde3 by task syz-executor.0/7549
CPU: 0 PID: 7549 Comm: syz-executor.0 Not tainted 6.8.0-syzkaller-08951-gfe46a7dd189e #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 03/27/2024
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x241/0x360 lib/dump_stack.c:114
print_address_description mm/kasan/report.c:377 [inline]
print_report+0x169/0x550 mm/kasan/report.c:488
kasan_report+0x143/0x180 mm/kasan/report.c:601
copy_from_sockptr_offset include/linux/sockptr.h:49 [inline]
copy_from_sockptr include/linux/sockptr.h:55 [inline]
xsk_setsockopt+0x909/0xa40 net/xdp/xsk.c:1420
do_sock_setsockopt+0x3af/0x720 net/socket.c:2311
__sys_setsockopt+0x1ae/0x250 net/socket.c:2334
__do_sys_setsockopt net/socket.c:2343 [inline]
__se_sys_setsockopt net/socket.c:2340 [inline]
__x64_sys_setsockopt+0xb5/0xd0 net/socket.c:2340
do_syscall_64+0xfb/0x240
entry_SYSCALL_64_after_hwframe+0x6d/0x75
RIP: 0033:0x7fb40587de69
Code: 28 00 00 00 75 05 48 83 c4 28 c3 e8 e1 20 00 00 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b0 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007fb40665a0c8 EFLAGS: 00000246 ORIG_RAX: 0000000000000036
RAX: ffffffffffffffda RBX: 00007fb4059abf80 RCX: 00007fb40587de69
RDX: 0000000000000005 RSI: 000000000000011b RDI: 0000000000000006
RBP: 00007fb4058ca47a R08: 0000000000000002 R09: 0000000000000000
R10: 0000000020001980 R11: 0000000000000246 R12: 0000000000000000
R13: 000000000000000b R14: 00007fb4059abf80 R15: 00007fff57ee4d08
</TASK>
Allocated by task 7549:
kasan_save_stack mm/kasan/common.c:47 [inline]
kasan_save_track+0x3f/0x80 mm/kasan/common.c:68
poison_kmalloc_redzone mm/kasan/common.c:370 [inline]
__kasan_kmalloc+0x98/0xb0 mm/kasan/common.c:387
kasan_kmalloc include/linux/kasan.h:211 [inline]
__do_kmalloc_node mm/slub.c:3966 [inline]
__kmalloc+0x233/0x4a0 mm/slub.c:3979
kmalloc include/linux/slab.h:632 [inline]
__cgroup_bpf_run_filter_setsockopt+0xd2f/0x1040 kernel/bpf/cgroup.c:1869
do_sock_setsockopt+0x6b4/0x720 net/socket.c:2293
__sys_setsockopt+0x1ae/0x250 net/socket.c:2334
__do_sys_setsockopt net/socket.c:2343 [inline]
__se_sys_setsockopt net/socket.c:2340 [inline]
__x64_sys_setsockopt+0xb5/0xd0 net/socket.c:2340
do_syscall_64+0xfb/0x240
entry_SYSCALL_64_after_hwframe+0x6d/0x75
The buggy address belongs to the object at ffff888028c6cde0
which belongs to the cache kmalloc-8 of size 8
The buggy address is located 1 bytes to the right of
allocated 2-byte region [ffff888028c6cde0, ffff888028c6cde2)
The buggy address belongs to the physical page:
page:ffffea0000a31b00 refcount:1 mapcount:0 mapping:0000000000000000 index:0xffff888028c6c9c0 pfn:0x28c6c
anon flags: 0xfff00000000800(slab|node=0|zone=1|lastcpupid=0x7ff)
page_type: 0xffffffff()
raw: 00fff00000000800 ffff888014c41280 0000000000000000 dead000000000001
raw: ffff888028c6c9c0 0000000080800057 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
page_owner tracks the page as allocated
page last allocated via order 0, migratetype Unmovable, gfp_mask 0x112cc0(GFP_USER|__GFP_NOWARN|__GFP_NORETRY), pid 6648, tgid 6644 (syz-executor.0), ts 133906047828, free_ts 133859922223
set_page_owner include/linux/page_owner.h:31 [inline]
post_alloc_hook+0x1ea/0x210 mm/page_alloc.c:1533
prep_new_page mm/page_alloc.c:1540 [inline]
get_page_from_freelist+0x33ea/0x3580 mm/page_alloc.c:3311
__alloc_pages+0x256/0x680 mm/page_alloc.c:4569
__alloc_pages_node include/linux/gfp.h:238 [inline]
alloc_pages_node include/linux/gfp.h:261 [inline]
alloc_slab_page+0x5f/0x160 mm/slub.c:2175
allocate_slab mm/slub.c:2338 [inline]
new_slab+0x84/0x2f0 mm/slub.c:2391
___slab_alloc+0xc73/0x1260 mm/slub.c:3525
__slab_alloc mm/slub.c:3610 [inline]
__slab_alloc_node mm/slub.c:3663 [inline]
slab_alloc_node mm/slub.c:3835 [inline]
__do_kmalloc_node mm/slub.c:3965 [inline]
__kmalloc_node+0x2db/0x4e0 mm/slub.c:3973
kmalloc_node include/linux/slab.h:648 [inline]
__vmalloc_area_node mm/vmalloc.c:3197 [inline]
__vmalloc_node_range+0x5f9/0x14a0 mm/vmalloc.c:3392
__vmalloc_node mm/vmalloc.c:3457 [inline]
vzalloc+0x79/0x90 mm/vmalloc.c:3530
bpf_check+0x260/0x19010 kernel/bpf/verifier.c:21162
bpf_prog_load+0x1667/0x20f0 kernel/bpf/syscall.c:2895
__sys_bpf+0x4ee/0x810 kernel/bpf/syscall.c:5631
__do_sys_bpf kernel/bpf/syscall.c:5738 [inline]
__se_sys_bpf kernel/bpf/syscall.c:5736 [inline]
__x64_sys_bpf+0x7c/0x90 kernel/bpf/syscall.c:5736
do_syscall_64+0xfb/0x240
entry_SYSCALL_64_after_hwframe+0x6d/0x75
page last free pid 6650 tgid 6647 stack trace:
reset_page_owner include/linux/page_owner.h:24 [inline]
free_pages_prepare mm/page_alloc.c:1140 [inline]
free_unref_page_prepare+0x95d/0xa80 mm/page_alloc.c:2346
free_unref_page_list+0x5a3/0x850 mm/page_alloc.c:2532
release_pages+0x2117/0x2400 mm/swap.c:1042
tlb_batch_pages_flush mm/mmu_gather.c:98 [inline]
tlb_flush_mmu_free mm/mmu_gather.c:293 [inline]
tlb_flush_mmu+0x34d/0x4e0 mm/mmu_gather.c:300
tlb_finish_mmu+0xd4/0x200 mm/mmu_gather.c:392
exit_mmap+0x4b6/0xd40 mm/mmap.c:3300
__mmput+0x115/0x3c0 kernel/fork.c:1345
exit_mm+0x220/0x310 kernel/exit.c:569
do_exit+0x99e/0x27e0 kernel/exit.c:865
do_group_exit+0x207/0x2c0 kernel/exit.c:1027
get_signal+0x176e/0x1850 kernel/signal.c:2907
arch_do_signal_or_restart+0x96/0x860 arch/x86/kernel/signal.c:310
exit_to_user_mode_loop kernel/entry/common.c:105 [inline]
exit_to_user_mode_prepare include/linux/entry-common.h:328 [inline]
__syscall_exit_to_user_mode_work kernel/entry/common.c:201 [inline]
syscall_exit_to_user_mode+0xc9/0x360 kernel/entry/common.c:212
do_syscall_64+0x10a/0x240 arch/x86/entry/common.c:89
entry_SYSCALL_64_after_hwframe+0x6d/0x75
Memory state around the buggy address:
ffff888028c6cc80: fa fc fc fc fa fc fc fc fa fc fc fc fa fc fc fc
ffff888028c6cd00: fa fc fc fc fa fc fc fc 00 fc fc fc 06 fc fc fc
>ffff888028c6cd80: fa fc fc fc fa fc fc fc fa fc fc fc 02 fc fc fc
^
ffff888028c6ce00: fa fc fc fc fa fc fc fc fa fc fc fc fa fc fc fc
ffff888028c6ce80: fa fc fc fc fa fc fc fc fa fc fc fc fa fc fc fc
Fixes: 423f38329d ("xsk: add umem fill queue support and mmap")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: "Björn Töpel" <bjorn@kernel.org>
Cc: Magnus Karlsson <magnus.karlsson@intel.com>
Cc: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Cc: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/r/20240404202738.3634547-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4539f91f2a ]
On startup, ovs-vswitchd probes different datapath features including
support for timeout policies. While probing, it tries to execute
certain operations with OVS_PACKET_ATTR_PROBE or OVS_FLOW_ATTR_PROBE
attributes set. These attributes tell the openvswitch module to not
log any errors when they occur as it is expected that some of the
probes will fail.
For some reason, setting the timeout policy ignores the PROBE attribute
and logs a failure anyway. This is causing the following kernel log
on each re-start of ovs-vswitchd:
kernel: Failed to associated timeout policy `ovs_test_tp'
Fix that by using the same logging macro that all other messages are
using. The message will still be printed at info level when needed
and will be rate limited, but with a net rate limiter instead of
generic printk one.
The nf_ct_set_timeout() itself will still print some info messages,
but at least this change makes logging in openvswitch module more
consistent.
Fixes: 06bd2bdf19 ("openvswitch: Add timeout support to ct action")
Signed-off-by: Ilya Maximets <i.maximets@ovn.org>
Acked-by: Eelco Chaudron <echaudro@redhat.com>
Link: https://lore.kernel.org/r/20240403203803.2137962-1-i.maximets@ovn.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 185fdb4697 ]
Calling a function through an incompatible pointer type causes breaks
kcfi, so clang warns about the assignment:
drivers/gpu/drm/nouveau/nvkm/subdev/bios/shadowof.c:73:10: error: cast from 'void (*)(const void *)' to 'void (*)(void *)' converts to incompatible function type [-Werror,-Wcast-function-type-strict]
73 | .fini = (void(*)(void *))kfree,
Avoid this with a trivial wrapper.
Fixes: c39f472e9f ("drm/nouveau: remove symlinks, move core/ to nvkm/ (no code changes)")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240404160234.2923554-1-arnd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f7c52345cc ]
Since mbox_cmd.size_out is overwritten with the actual output size in
the function below, it needs to be initialized every time.
cxl_internal_send_cmd -> __cxl_pci_mbox_send_cmd
Problem scenario:
1) The size_out variable is initially set to the size of the mailbox.
2) Read an event.
- size_out is set to 160 bytes(header 32B + one event 128B).
- Two event are created while reading.
3) Read the new *two* events.
- size_out is still set to 160 bytes.
- Although the value of out_len is 288 bytes, only 160 bytes are
copied from the mailbox register to the local variable.
- record_count is set to 2.
- Accessing records[1] will result in reading incorrect data.
Fixes: 6ebe28f9ec ("cxl/mem: Read, trace, and clear events on driver load")
Tested-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Kwangjin Ko <kwangjin.ko@sk.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c88a9ccd4 ]
In the error path, map->reg_type is being used for kernel warning
before its value is setup. Found by code inspection. Exposure to
user is wrong reg_type being emitted via kernel log. Use a local
var for reg_type and retrieve value for usage.
Fixes: 6c7f4f1e51 ("cxl/core/regs: Make cxl_map_{component, device}_regs() device generic")
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Davidlohr Bueso <dave@stgolabs.net>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b7c59b038c ]
The dev_dbg info for Clear Event Records mailbox command would report
the handle of the next record to clear not the current one.
This was because the index 'i' had incremented before printing the
current handle value.
Fixes: 6ebe28f9ec ("cxl/mem: Read, trace, and clear events on driver load")
Signed-off-by: Yuquan Wang <wangyuquan1236@phytium.com.cn>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 894ad61b85 ]
Commit e519f0bb64 ("ARM/mmc: Convert old mmci-omap to GPIO descriptors")
moved Nokia N810 MMC power up/down from the board file into the MMC driver.
The change removed some delays, and ordering without a valid reason.
Restore power up/down to match the original code. This matters only on N810
where the 2nd GPIO is in use. Other boards will see an additional delay but
that should be a lesser concern than omitting delays altogether.
Fixes: e519f0bb64 ("ARM/mmc: Convert old mmci-omap to GPIO descriptors")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Message-ID: <20240223181439.1099750-6-aaro.koskinen@iki.fi>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ce5d241c3a upstream.
The valid_la is used to check the length requirements,
including special cases of Timer Status. If the length is
shorter than 5, that means no Duration Available is returned,
the message will be forced to be invalid.
However, the description of Duration Available in the spec
is that this parameter may be returned when these cases, or
that it can be optionally return when these cases. The key
words in the spec description are flexible choices.
Remove the special length check of Timer Status to fit the
spec which is not compulsory about that.
Signed-off-by: Nini Song <nini.song@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c89a068bf upstream.
s2idle works like a regular suspend with freezing processes and freezing
devices. All CPUs except the control CPU go into idle. Once this is
completed the control CPU kicks all other CPUs out of idle, so that they
reenter the idle loop and then enter s2idle state. The control CPU then
issues an swait() on the suspend state and therefore enters the idle loop
as well.
Due to being kicked out of idle, the other CPUs leave their NOHZ states,
which means the tick is active and the corresponding hrtimer is programmed
to the next jiffie.
On entering s2idle the CPUs shut down their local clockevent device to
prevent wakeups. The last CPU which enters s2idle shuts down its local
clockevent and freezes timekeeping.
On resume, one of the CPUs receives the wakeup interrupt, unfreezes
timekeeping and its local clockevent and starts the resume process. At that
point all other CPUs are still in s2idle with their clockevents switched
off. They only resume when they are kicked by another CPU or after resuming
devices and then receiving a device interrupt.
That means there is no guarantee that all CPUs will wakeup directly on
resume. As a consequence there is no guarantee that timers which are queued
on those CPUs and should expire directly after resume, are handled. Also
timer list timers which are remotely queued to one of those CPUs after
resume will not result in a reprogramming IPI as the tick is
active. Queueing a hrtimer will also not result in a reprogramming IPI
because the first hrtimer event is already in the past.
The recent introduction of the timer pull model (7ee9887703 ("timers:
Implement the hierarchical pull model")) amplifies this problem, if the
current migrator is one of the non woken up CPUs. When a non pinned timer
list timer is queued and the queuing CPU goes idle, it relies on the still
suspended migrator CPU to expire the timer which will happen by chance.
The problem exists since commit 8d89835b04 ("PM: suspend: Do not pause
cpuidle in the suspend-to-idle path"). There the cpuidle_pause() call which
in turn invoked a wakeup for all idle CPUs was moved to a later point in
the resume process. This might not be reached or reached very late because
it waits on a timer of a still suspended CPU.
Address this by kicking all CPUs out of idle after the control CPU returns
from swait() so that they resume their timers and restore consistent system
state.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218641
Fixes: 8d89835b04 ("PM: suspend: Do not pause cpuidle in the suspend-to-idle path")
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Mario Limonciello <mario.limonciello@amd.com>
Cc: 5.16+ <stable@kernel.org> # 5.16+
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d730192ff0 upstream.
On the Toshiba Encore WT10-A tablet the BATC battery ACPI device depends
on 3 other devices:
Name (_DEP, Package (0x03) // _DEP: Dependencies
{
I2C1,
GPO2,
GPO0
})
acpi_scan_check_dep() adds all 3 of these to the acpi_dep_list and then
before an acpi_device is created for the BATC handle (and thus before
acpi_scan_dep_init() runs) acpi_scan_clear_dep() gets called for both
GPIO depenencies, with free_when_met not set for the dependencies.
Since there is no adev for BATC yet, there also is no dep_unmet to
decrement. The only result of acpi_scan_clear_dep() in this case is
dep->met getting set.
Soon after acpi_scan_clear_dep() has been called for the GPIO dependencies
the acpi_device gets created for the BATC handle and acpi_scan_dep_init()
runs, this sees 3 dependencies on the acpi_dep_list and initializes
unmet_dep to 3. Later when the dependency for I2C1 is met unmet_dep
becomes 2, but since the 2 GPIO deps where already met it never becomes 0
causing battery monitoring to not work.
Fix this by modifying acpi_scan_dep_init() to not increase dep_met for
dependencies which have already been marked as being met.
Fixes: 3ba12d8de3 ("ACPI: scan: Reduce overhead related to devices with dependencies")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: 6.5+ <stable@vger.kernel.org> # 6.5+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e700b384e upstream.
The cros_ec_uart_probe() function calls devm_serdev_device_open() before
it calls serdev_device_set_client_ops(). This can trigger a NULL pointer
dereference:
BUG: kernel NULL pointer dereference, address: 0000000000000000
...
Call Trace:
<TASK>
...
? ttyport_receive_buf
A simplified version of crashing code is as follows:
static inline size_t serdev_controller_receive_buf(struct serdev_controller *ctrl,
const u8 *data,
size_t count)
{
struct serdev_device *serdev = ctrl->serdev;
if (!serdev || !serdev->ops->receive_buf) // CRASH!
return 0;
return serdev->ops->receive_buf(serdev, data, count);
}
It assumes that if SERPORT_ACTIVE is set and serdev exists, serdev->ops
will also exist. This conflicts with the existing cros_ec_uart_probe()
logic, as it first calls devm_serdev_device_open() (which sets
SERPORT_ACTIVE), and only later sets serdev->ops via
serdev_device_set_client_ops().
Commit 01f95d42b8 ("platform/chrome: cros_ec_uart: fix race
condition") attempted to fix a similar race condition, but while doing
so, made the window of error for this race condition to happen much
wider.
Attempt to fix the race condition again, making sure we fully setup
before calling devm_serdev_device_open().
Fixes: 01f95d42b8 ("platform/chrome: cros_ec_uart: fix race condition")
Cc: stable@vger.kernel.org
Signed-off-by: Noah Loomans <noah@noahloomans.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Link: https://lore.kernel.org/r/20240410182618.169042-2-noah@noahloomans.com
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 31729e8c21 upstream.
While doing multiple S4 stress tests, GC/RLC/PMFW get into
an invalid state resulting into hard hangs.
Adding a GFX reset as workaround just before sending the
MP1_UNLOAD message avoids this failure.
Signed-off-by: Tim Huang <Tim.Huang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Mario Limonciello <superm1@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ffe3986fec upstream.
The "buffer_percent" logic that is used by the ring buffer splice code to
only wake up the tasks when there's no data after the buffer is filled to
the percentage of the "buffer_percent" file is dependent on three
variables that determine the amount of data that is in the ring buffer:
1) pages_read - incremented whenever a new sub-buffer is consumed
2) pages_lost - incremented every time a writer overwrites a sub-buffer
3) pages_touched - incremented when a write goes to a new sub-buffer
The percentage is the calculation of:
(pages_touched - (pages_lost + pages_read)) / nr_pages
Basically, the amount of data is the total number of sub-bufs that have been
touched, minus the number of sub-bufs lost and sub-bufs consumed. This is
divided by the total count to give the buffer percentage. When the
percentage is greater than the value in the "buffer_percent" file, it
wakes up splice readers waiting for that amount.
It was observed that over time, the amount read from the splice was
constantly decreasing the longer the trace was running. That is, if one
asked for 60%, it would read over 60% when it first starts tracing, but
then it would be woken up at under 60% and would slowly decrease the
amount of data read after being woken up, where the amount becomes much
less than the buffer percent.
This was due to an accounting of the pages_touched incrementation. This
value is incremented whenever a writer transfers to a new sub-buffer. But
the place where it was incremented was incorrect. If a writer overflowed
the current sub-buffer it would go to the next one. If it gets preempted
by an interrupt at that time, and the interrupt performs a trace, it too
will end up going to the next sub-buffer. But only one should increment
the counter. Unfortunately, that was not the case.
Change the cmpxchg() that does the real switch of the tail-page into a
try_cmpxchg(), and on success, perform the increment of pages_touched. This
will only increment the counter once for when the writer moves to a new
sub-buffer, and not when there's a race and is incremented for when a
writer and its preempting writer both move to the same new sub-buffer.
Link: https://lore.kernel.org/linux-trace-kernel/20240409151309.0d0e5056@gandalf.local.home
Cc: stable@vger.kernel.org
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Fixes: 2c2b0a78b3 ("ring-buffer: Add percentage of ring buffer full to wake up reader")
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fcf3f7e2fc upstream.
r1_bio->bios[] is used to record new bios that will be issued to
underlying disks, however, in raid1_write_request(), r1_bio->bios[]
will set to the original bio temporarily. Meanwhile, if blocked rdev
is set, free_r1bio() will be called causing that all r1_bio->bios[]
to be freed:
raid1_write_request()
r1_bio = alloc_r1bio(mddev, bio); -> r1_bio->bios[] is NULL
for (i = 0; i < disks; i++) -> for each rdev in conf
// first rdev is normal
r1_bio->bios[0] = bio; -> set to original bio
// second rdev is blocked
if (test_bit(Blocked, &rdev->flags))
break
if (blocked_rdev)
free_r1bio()
put_all_bios()
bio_put(r1_bio->bios[0]) -> original bio is freed
Test scripts:
mdadm -CR /dev/md0 -l1 -n4 /dev/sd[abcd] --assume-clean
fio -filename=/dev/md0 -ioengine=libaio -rw=write -bs=4k -numjobs=1 \
-iodepth=128 -name=test -direct=1
echo blocked > /sys/block/md0/md/rd2/state
Test result:
BUG bio-264 (Not tainted): Object already free
-----------------------------------------------------------------------------
Allocated in mempool_alloc_slab+0x24/0x50 age=1 cpu=1 pid=869
kmem_cache_alloc+0x324/0x480
mempool_alloc_slab+0x24/0x50
mempool_alloc+0x6e/0x220
bio_alloc_bioset+0x1af/0x4d0
blkdev_direct_IO+0x164/0x8a0
blkdev_write_iter+0x309/0x440
aio_write+0x139/0x2f0
io_submit_one+0x5ca/0xb70
__do_sys_io_submit+0x86/0x270
__x64_sys_io_submit+0x22/0x30
do_syscall_64+0xb1/0x210
entry_SYSCALL_64_after_hwframe+0x6c/0x74
Freed in mempool_free_slab+0x1f/0x30 age=1 cpu=1 pid=869
kmem_cache_free+0x28c/0x550
mempool_free_slab+0x1f/0x30
mempool_free+0x40/0x100
bio_free+0x59/0x80
bio_put+0xf0/0x220
free_r1bio+0x74/0xb0
raid1_make_request+0xadf/0x1150
md_handle_request+0xc7/0x3b0
md_submit_bio+0x76/0x130
__submit_bio+0xd8/0x1d0
submit_bio_noacct_nocheck+0x1eb/0x5c0
submit_bio_noacct+0x169/0xd40
submit_bio+0xee/0x1d0
blkdev_direct_IO+0x322/0x8a0
blkdev_write_iter+0x309/0x440
aio_write+0x139/0x2f0
Since that bios for underlying disks are not allocated yet, fix this
problem by using mempool_free() directly to free the r1_bio.
Fixes: 992db13a4a ("md/raid1: free the r1bio before waiting for blocked rdev")
Cc: stable@vger.kernel.org # v6.6+
Reported-by: Coly Li <colyli@suse.de>
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Tested-by: Coly Li <colyli@suse.de>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20240308093726.1047420-1-yukuai1@huaweicloud.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b1f532a3b1 upstream.
If the MTU of one of an attached interface becomes too small to transmit
the local translation table then it must be resized to fit inside all
fragments (when enabled) or a single packet.
But if the MTU becomes too low to transmit even the header + the VLAN
specific part then the resizing of the local TT will never succeed. This
can for example happen when the usable space is 110 bytes and 11 VLANs are
on top of batman-adv. In this case, at least 116 byte would be needed.
There will just be an endless spam of
batman_adv: batadv0: Forced to purge local tt entries to fit new maximum fragment MTU (110)
in the log but the function will never finish. Problem here is that the
timeout will be halved all the time and will then stagnate at 0 and
therefore never be able to reduce the table even more.
There are other scenarios possible with a similar result. The number of
BATADV_TT_CLIENT_NOPURGE entries in the local TT can for example be too
high to fit inside a packet. Such a scenario can therefore happen also with
only a single VLAN + 7 non-purgable addresses - requiring at least 120
bytes.
While this should be handled proactively when:
* interface with too low MTU is added
* VLAN is added
* non-purgeable local mac is added
* MTU of an attached interface is reduced
* fragmentation setting gets disabled (which most likely requires dropping
attached interfaces)
not all of these scenarios can be prevented because batman-adv is only
consuming events without the the possibility to prevent these actions
(non-purgable MAC address added, MTU of an attached interface is reduced).
It is therefore necessary to also make sure that the code is able to handle
also the situations when there were already incompatible system
configuration are present.
Cc: stable@vger.kernel.org
Fixes: a19d3d85e1 ("batman-adv: limit local translation table max size")
Reported-by: syzbot+a6a4b5bb3da165594cff@syzkaller.appspotmail.com
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7933650478 upstream.
Commit 0c76106cb9 ("scsi: sd: Fix TCG OPAL unlock on system resume")
incorrectly handles failures of scsi_resume_device() in
ata_scsi_dev_rescan(), leading to a double call to
spin_unlock_irqrestore() to unlock a device port. Fix this by redefining
the goto labels used in case of errors and only unlock the port
scsi_scan_mutex when scsi_resume_device() fails.
Bug found with the Smatch static checker warning:
drivers/ata/libata-scsi.c:4774 ata_scsi_dev_rescan()
error: double unlocked 'ap->lock' (orig line 4757)
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Fixes: 0c76106cb9 ("scsi: sd: Fix TCG OPAL unlock on system resume")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c0297e7dd5 upstream.
Even though the command duration limits (CDL) feature was first added
in ACS-5 (major version 12), there are some ACS-4 (major version 11)
drives that implement CDL as well.
IDENTIFY_DEVICE, SUPPORTED_CAPABILITIES, and CURRENT_SETTINGS log pages
are mandatory in the ACS-4 standard so it should be safe to read these
log pages on older drives implementing the ACS-4 standard.
Fixes: 62e4a60e0c ("scsi: ata: libata: Detect support for command duration limits")
Cc: stable@vger.kernel.org
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the 6.6 kernel, devices that use the raspberrypi firmware driver
should be children of the firmware node.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
This commit fixes uvc gadget support on 32-bit platforms.
Commit 0df28607c5 ("usb: gadget: uvc: Generalise helper functions for
reuse") introduced a helper function __uvcg_iter_item_entries() to aid
with parsing lists of items on configfs attributes stores. This function
is a generalization of another very similar function, which used a
stack-allocated temporary buffer of fixed size for each item in the list
and used the sizeof() operator to check for potential buffer overruns.
The new function was changed to allocate the now variably sized temp
buffer on heap, but wasn't properly updated to also check for max buffer
size using the computed size instead of sizeof() operator.
As a result, the maximum item size was 7 (plus null terminator) on
64-bit platforms, and 3 on 32-bit ones. While 7 is accidentally just
barely enough, 3 is definitely too small for some of UVC configfs
attributes. For example, dwFrameInteval, specified in 100ns units,
usually has 6-digit item values, e.g. 166666 for 60fps.
Fixes: 0df28607c5 ("usb: gadget: uvc: Generalise helper functions for reuse")
Signed-off-by: Ivan Avdeev <me@provod.works>
commit 025f8ad20f upstream.
mpls_gso_segment() assumes skb_inner_network_header() returns
a valid result:
mpls_hlen = skb_inner_network_header(skb) - skb_network_header(skb);
if (unlikely(!mpls_hlen || mpls_hlen % MPLS_HLEN))
goto out;
if (unlikely(!pskb_may_pull(skb, mpls_hlen)))
With syzbot reproducer, skb_inner_network_header() yields 0,
skb_network_header() returns 108, so this will
"pskb_may_pull(skb, -108)))" which triggers a newly added
DEBUG_NET_WARN_ON_ONCE() check:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 5068 at include/linux/skbuff.h:2723 pskb_may_pull_reason include/linux/skbuff.h:2723 [inline]
WARNING: CPU: 0 PID: 5068 at include/linux/skbuff.h:2723 pskb_may_pull include/linux/skbuff.h:2739 [inline]
WARNING: CPU: 0 PID: 5068 at include/linux/skbuff.h:2723 mpls_gso_segment+0x773/0xaa0 net/mpls/mpls_gso.c:34
[..]
skb_mac_gso_segment+0x383/0x740 net/core/gso.c:53
nsh_gso_segment+0x40a/0xad0 net/nsh/nsh.c:108
skb_mac_gso_segment+0x383/0x740 net/core/gso.c:53
__skb_gso_segment+0x324/0x4c0 net/core/gso.c:124
skb_gso_segment include/net/gso.h:83 [inline]
[..]
sch_direct_xmit+0x11a/0x5f0 net/sched/sch_generic.c:327
[..]
packet_sendmsg+0x46a9/0x6130 net/packet/af_packet.c:3113
[..]
First iteration of this patch made mpls_hlen signed and changed
test to error out to "mpls_hlen <= 0 || ..".
Eric Dumazet said:
> I was thinking about adding a debug check in skb_inner_network_header()
> if inner_network_header is zero (that would mean it is not 'set' yet),
> but this would trigger even after your patch.
So add new skb_inner_network_header_was_set() helper and use that.
The syzbot reproducer injects data via packet socket. The skb that gets
allocated and passed down the stack has ->protocol set to NSH (0x894f)
and gso_type set to SKB_GSO_UDP | SKB_GSO_DODGY.
This gets passed to skb_mac_gso_segment(), which sees NSH as ptype to
find a callback for. nsh_gso_segment() retrieves next type:
proto = tun_p_to_eth_p(nsh_hdr(skb)->np);
... which is MPLS (TUN_P_MPLS_UC). It updates skb->protocol and then
calls mpls_gso_segment(). Inner offsets are all 0, so mpls_gso_segment()
ends up with a negative header size.
In case more callers rely on silent handling of such large may_pull values
we could also 'legalize' this behaviour, either replacing the debug check
with (len > INT_MAX) test or removing it and instead adding a comment
before existing
if (unlikely(len > skb->len))
return SKB_DROP_REASON_PKT_TOO_SMALL;
test in pskb_may_pull_reason(), saying that this check also implicitly
takes care of callers that miscompute header sizes.
Cc: Simon Horman <horms@kernel.org>
Fixes: 219eee9c0d ("net: skbuff: add overflow debug check to pull/push helpers")
Reported-by: syzbot+99d15fcdb0132a1e1a82@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/netdev/00000000000043b1310611e388aa@google.com/raw
Signed-off-by: Florian Westphal <fw@strlen.de>
Link: https://lore.kernel.org/r/20240222140321.14080-1-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 434e5781d8 ]
ACER Vivobook Flip (TP401NAS) virtual intel switch is implemented as
follow:
Device (VGBI)
{
Name (_HID, EisaId ("INT33D6") ...
Name (VBDS, Zero)
Method (_STA, 0, Serialized) // _STA: Status ...
Method (VBDL, 0, Serialized)
{
PB1E |= 0x20
VBDS |= 0x40
}
Method (VGBS, 0, Serialized)
{
Return (VBDS) /* \_SB_.PCI0.SBRG.EC0_.VGBI.VBDS */
}
...
}
By default VBDS is set to 0. At boot it is set to clamshell (bit 6 set)
only after method VBDL is executed.
Since VBDL is now evaluated in the probe routine later, after the device
is registered, the retrieved value of VBDS was still 0 ("tablet mode")
when setting up the virtual switch.
Make sure to evaluate VGBS after VBDL, to ensure the
convertible boots in clamshell mode, the expected default.
Fixes: 26173179fa ("platform/x86: intel-vbtn: Eval VBDL after registering our notifier")
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240329143206.2977734-3-gwendal@chromium.org
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2d953276b ]
The expression htotal * vtotal can have a zero value on
overflow. It is necessary to prevent division by zero like in
fb_var_to_videomode().
Found by Linux Verification Center (linuxtesting.org) with Svace.
Signed-off-by: Roman Smirnov <r.smirnov@omp.ru>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e89086c43f ]
This commit adds NVME_QUIRK_NO_DEEPEST_PS and NVME_QUIRK_BOGUS_NID for
device [126f:2262], which appears to be a generic VID:PID pair used for
many SSDs based on the Silicon Motion SM2262/SM2262EN controller.
Two of my SSDs with this VID:PID pair exhibit the same behavior:
* They frequently have trouble exiting the deepest power state (5),
resulting in the entire disk unresponsive.
Verified by setting nvme_core.default_ps_max_latency_us=10000 and
observing them behaving normally.
* They produce all-zero nguid and eui64 with `nvme id-ns` command.
The offending products are:
* HP SSD EX950 1TB
* HIKVISION C2000Pro 2TB
Signed-off-by: Jiawei Fu <i@ibugone.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23dfd914d2 ]
If the find_fromsym() call fails and returns NULL, the warn() call
will dereference this NULL pointer and cause the program to crash.
This happened when I tried to build with "test_user_copy" module.
With this fix, it prints lots of warnings like this:
WARNING: modpost: lib/test_user_copy: section mismatch in reference: (unknown)+0x4 (section: .text.fixup) -> (unknown) (section: .init.text)
masahiroy@kernel.org:
The issue is reproduced with ARCH=arm allnoconfig + CONFIG_MODULES=y +
CONFIG_RUNTIME_TESTING_MENU=y + CONFIG_TEST_USER_COPY=m
Signed-off-by: Max Kellermann <max.kellermann@ionos.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e21e1c45e1 ]
If failure happens before the opcode prep handler is called, ensure that
we clear the opcode specific area of the request, which holds data
specific to that request type. This prevents errors where opcode
handlers either don't get to clear per-request private data since prep
isn't even called.
Reported-and-tested-by: syzbot+f8e9a371388aa62ecab4@syzkaller.appspotmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc87bb342f ]
There are some actions with value 'tmp' but 'dst_addr' is checked instead.
It is obvious that a copy-paste error was made here and the value
of variable 'tmp' should be checked here.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Aleksandr Burakov <a.burakov@rosalinux.ru>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 38620fc4e8 ]
When running as PVH or HVM Linux will use holes in the memory map as scratch
space to map grants, foreign domain pages and possibly miscellaneous other
stuff. However the usage of such memory map holes for Xen purposes can be
problematic. The request of holesby Xen happen quite early in the kernel boot
process (grant table setup already uses scratch map space), and it's possible
that by then not all devices have reclaimed their MMIO space. It's not
unlikely for chunks of Xen scratch map space to end up using PCI bridge MMIO
window memory, which (as expected) causes quite a lot of issues in the system.
At least for PVH dom0 we have the possibility of using regions marked as
UNUSABLE in the e820 memory map. Either if the region is UNUSABLE in the
native memory map, or it has been converted into UNUSABLE in order to hide RAM
regions from dom0, the second stage translation page-tables can populate those
areas without issues.
PV already has this kind of logic, where the balloon driver is inflated at
boot. Re-use the current logic in order to also inflate it when running as
PVH. onvert UNUSABLE regions up to the ratio specified in EXTRA_MEM_RATIO to
RAM, while reserving them using xen_add_extra_mem() (which is also moved so
it's no longer tied to CONFIG_PV).
[jgross: fixed build for CONFIG_PVH without CONFIG_XEN_PVH]
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20240220174341.56131-1-roger.pau@citrix.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23fb6bc269 ]
When pcm_runtime is adding platform components it will scan all
registered components. In case of DPCM FE/BE some DAI links will
configure dummy platform. However both dummy codec and dummy platform
are using "snd-soc-dummy" as component->name. Dummy codec should be
skipped when adding platforms otherwise there'll be overflow and UBSAN
complains.
Reported-by: Zhipeng Wang <zhipeng.wang_1@nxp.com>
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Link: https://msgid.link/r/20240305065606.3778642-1-chancel.liu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a75e0684ef ]
If a DiplayPort cable is directly connected to the host routers USB4
port, there is no tunnel involved but the port is in "redrive" mode
meaning that it is re-driving the DisplayPort signals from its
DisplayPort source. In this case we need to keep the domain powered on
otherwise once the domain enters D3cold the connected monitor blanks
too.
Since this happens only on Intel Barlow Ridge add a quirk that takes
runtime PM reference if we detect that the USB4 port entered redrive
mode (and release it once it exits the mode).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4207b556e6 ]
The BPF helper bpf_cgroup_from_id() calls kernfs_find_and_get_node_by_id()
which acquires kernfs_idr_lock, which is an non-raw non-IRQ-safe lock. This
can lead to deadlocks as bpf_cgroup_from_id() can be called from any BPF
programs including e.g. the ones that attach to functions which are holding
the scheduler rq lock.
Consider the following BPF program:
SEC("fentry/__set_cpus_allowed_ptr_locked")
int BPF_PROG(__set_cpus_allowed_ptr_locked, struct task_struct *p,
struct affinity_context *affn_ctx, struct rq *rq, struct rq_flags *rf)
{
struct cgroup *cgrp = bpf_cgroup_from_id(p->cgroups->dfl_cgrp->kn->id);
if (cgrp) {
bpf_printk("%d[%s] in %s", p->pid, p->comm, cgrp->kn->name);
bpf_cgroup_release(cgrp);
}
return 0;
}
__set_cpus_allowed_ptr_locked() is called with rq lock held and the above
BPF program calls bpf_cgroup_from_id() within leading to the following
lockdep warning:
=====================================================
WARNING: HARDIRQ-safe -> HARDIRQ-unsafe lock order detected
6.7.0-rc3-work-00053-g07124366a1d7-dirty #147 Not tainted
-----------------------------------------------------
repro/1620 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire:
ffffffff833b3688 (kernfs_idr_lock){+.+.}-{2:2}, at: kernfs_find_and_get_node_by_id+0x1e/0x70
and this task is already holding:
ffff888237ced698 (&rq->__lock){-.-.}-{2:2}, at: task_rq_lock+0x4e/0xf0
which would create a new lock dependency:
(&rq->__lock){-.-.}-{2:2} -> (kernfs_idr_lock){+.+.}-{2:2}
...
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(kernfs_idr_lock);
local_irq_disable();
lock(&rq->__lock);
lock(kernfs_idr_lock);
<Interrupt>
lock(&rq->__lock);
*** DEADLOCK ***
...
Call Trace:
dump_stack_lvl+0x55/0x70
dump_stack+0x10/0x20
__lock_acquire+0x781/0x2a40
lock_acquire+0xbf/0x1f0
_raw_spin_lock+0x2f/0x40
kernfs_find_and_get_node_by_id+0x1e/0x70
cgroup_get_from_id+0x21/0x240
bpf_cgroup_from_id+0xe/0x20
bpf_prog_98652316e9337a5a___set_cpus_allowed_ptr_locked+0x96/0x11a
bpf_trampoline_6442545632+0x4f/0x1000
__set_cpus_allowed_ptr_locked+0x5/0x5a0
sched_setaffinity+0x1b3/0x290
__x64_sys_sched_setaffinity+0x4f/0x60
do_syscall_64+0x40/0xe0
entry_SYSCALL_64_after_hwframe+0x46/0x4e
Let's fix it by protecting kernfs_node and kernfs_root with RCU and making
kernfs_find_and_get_node_by_id() acquire rcu_read_lock() instead of
kernfs_idr_lock.
This adds an rcu_head to kernfs_node making it larger by 16 bytes on 64bit.
Combined with the preceding rearrange patch, the net increase is 8 bytes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Andrea Righi <andrea.righi@canonical.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20240109214828.252092-4-tj@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bce3f77068 ]
When processing a SYSERR, if the device does not respond to the MHI_RESET
from the host, the host will be stuck in a difficult to recover state.
The host will remain in MHI_PM_SYS_ERR_PROCESS and not clean up the host
channels. Clients will not be notified of the SYSERR via the destruction
of their channel devices, which means clients may think that the device is
still up. Subsequent SYSERR events such as a device fatal error will not
be processed as the state machine cannot transition from PROCESS back to
DETECT. The only way to recover from this is to unload the mhi module
(wipe the state machine state) or for the mhi controller to initiate
SHUTDOWN.
This issue was discovered by stress testing soc_reset events on AIC100
via the sysfs node.
soc_reset is processed entirely in hardware. When the register write
hits the endpoint hardware, it causes the soc to reset without firmware
involvement. In stress testing, there is a rare race where soc_reset N
will cause the soc to reset and PBL to signal SYSERR (fatal error). If
soc_reset N+1 is triggered before PBL can process the MHI_RESET from the
host, then the soc will reset again, and re-run PBL from the beginning.
This will cause PBL to lose all state. PBL will be waiting for the host
to respond to the new syserr, but host will be stuck expecting the
previous MHI_RESET to be processed.
Additionally, the AMSS EE firmware (QSM) was hacked to synthetically
reproduce the issue by simulating a FW hang after the QSM issued a
SYSERR. In this case, soc_reset would not recover the device.
For this failure case, to recover the device, we need a state similar to
PROCESS, but can transition to DETECT. There is not a viable existing
state to use. POR has the needed transitions, but assumes the device is
in a good state and could allow the host to attempt to use the device.
Allowing PROCESS to transition to DETECT invites the possibility of
parallel SYSERR processing which could get the host and device out of
sync.
Thus, invent a new state - MHI_PM_SYS_ERR_FAIL
This essentially a holding state. It allows us to clean up the host
elements that are based on the old state of the device (channels), but
does not allow us to directly advance back to an operational state. It
does allow the detection and processing of another SYSERR which may
recover the device, or allows the controller to do a clean shutdown.
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Carl Vanderlip <quic_carlv@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240112180800.536733-1-quic_jhugo@quicinc.com
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 07283c1873 ]
The test type "make_warnings_file" should have no mandatory configuration
parameters other than the ones required by the "build" test type, because
its purpose is to create a file with build warnings that may or may not be
used by other subsequent tests. Currently, the only way to use it as a
stand-alone test is by setting POWER_CYCLE, CONSOLE, SSH_USER,
BUILD_TARGET, TARGET_IMAGE, REBOOT_TYPE and GRUB_MENU.
Link: https://lkml.kernel.org/r/20240315-ktest-v2-1-c5c20a75f6a3@marliere.net
Cc: John Hawley <warthog9@eaglescrag.net>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b714a59b7 ]
The speakers on the Lenovo Yoga 9 14IMH9 are similar to previous generations
such as the 14IAP7, and the bass speakers can be fixed using similar methods
with one caveat: 14IMH9 uses CS35L41 amplifiers which need to be activated
separately.
Signed-off-by: Jichi Zhang <i@jichi.ca>
Message-ID: <20240315081954.45470-3-i@jichi.ca>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 96d9cbe2f2 ]
Add timeout to cm_destroy_id, so that userspace can trigger any data
collection that would help in analyzing the cause of delay in destroying
the cm_id.
New noinline function helps dtrace/ebpf programs to hook on to it.
Existing functionality isn't changed except triggering a probe-able new
function at every timeout interval.
We have seen cases where CM messages stuck with MAD layer (either due to
software bug or faulty HCA), leading to cm_id getting stuck in the
following call stack. This patch helps in resolving such issues faster.
kernel: ... INFO: task XXXX:56778 blocked for more than 120 seconds.
...
Call Trace:
__schedule+0x2bc/0x895
schedule+0x36/0x7c
schedule_timeout+0x1f6/0x31f
? __slab_free+0x19c/0x2ba
wait_for_completion+0x12b/0x18a
? wake_up_q+0x80/0x73
cm_destroy_id+0x345/0x610 [ib_cm]
ib_destroy_cm_id+0x10/0x20 [ib_cm]
rdma_destroy_id+0xa8/0x300 [rdma_cm]
ucma_destroy_id+0x13e/0x190 [rdma_ucm]
ucma_write+0xe0/0x160 [rdma_ucm]
__vfs_write+0x3a/0x16d
vfs_write+0xb2/0x1a1
? syscall_trace_enter+0x1ce/0x2b8
SyS_write+0x5c/0xd3
do_syscall_64+0x79/0x1b9
entry_SYSCALL_64_after_hwframe+0x16d/0x0
Signed-off-by: Manjunath Patil <manjunath.b.patil@oracle.com>
Link: https://lore.kernel.org/r/20240309063323.458102-1-manjunath.b.patil@oracle.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e10b6976f6 ]
HiSilicon UC PMU v2 suffers the erratum 162700402 that the PMU counter
cannot be set due to the lack of clock under power saving mode. This will
lead to error or inaccurate counts. The clock can be enabled by the PMU
global enabling control.
This patch tries to fix this by set the UC PMU enable before set event
period to turn on the clock, and then restore the UC PMU configuration.
The counter register can hold its value without a clock.
Signed-off-by: Junhao He <hejunhao3@huawei.com>
Reviewed-by: Yicong Yang <yangyicong@hisilicon.com>
Link: https://lore.kernel.org/r/20240227125231.53127-1-hejunhao3@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1947b92464 ]
Parallel testing appears to show a race between allocating and setting
evsel ids. As there is a bounds check on the xyarray it yields a segv
like:
```
AddressSanitizer:DEADLYSIGNAL
=================================================================
==484408==ERROR: AddressSanitizer: SEGV on unknown address 0x000000000010
==484408==The signal is caused by a WRITE memory access.
==484408==Hint: address points to the zero page.
#0 0x55cef5d4eff4 in perf_evlist__id_hash tools/lib/perf/evlist.c:256
#1 0x55cef5d4f132 in perf_evlist__id_add tools/lib/perf/evlist.c:274
#2 0x55cef5d4f545 in perf_evlist__id_add_fd tools/lib/perf/evlist.c:315
#3 0x55cef5a1923f in store_evsel_ids util/evsel.c:3130
#4 0x55cef5a19400 in evsel__store_ids util/evsel.c:3147
#5 0x55cef5888204 in __run_perf_stat tools/perf/builtin-stat.c:832
#6 0x55cef5888c06 in run_perf_stat tools/perf/builtin-stat.c:960
#7 0x55cef58932db in cmd_stat tools/perf/builtin-stat.c:2878
...
```
Avoid this crash by early exiting the perf_evlist__id_add_fd and
perf_evlist__id_add is the access is out-of-bounds.
Signed-off-by: Ian Rogers <irogers@google.com>
Cc: Yang Jihong <yangjihong1@huawei.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Link: https://lore.kernel.org/r/20240229070757.796244-1-irogers@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cdea98bf1f ]
The Asus B1400 with original shipped firmware versions and VMD disabled
cannot resume from suspend: the NVMe device becomes unresponsive and
inaccessible.
This appears to be an untested D3cold transition by the vendor; Intel
socwatch shows that Windows leaves the NVMe device and parent bridge in D0
during suspend, even though these firmware versions have StorageD3Enable=1.
The NVMe device and parent PCI bridge both share the same "PXP" ACPI power
resource, which gets turned off as both devices are put into D3cold during
suspend. The _OFF() method calls DL23() which sets a L23E bit at offset
0xe2 into the PCI configuration space for this root port. This is the
specific write that the _ON() routine is unable to recover from. This
register is not documented in the public chipset datasheet.
Disallow D3cold on the PCI bridge to enable successful suspend/resume.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215742
Link: https://lore.kernel.org/r/20240228075316.7404-1-drake@endlessos.org
Signed-off-by: Daniel Drake <drake@endlessos.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jian-Hong Pan <jhp@endlessos.org>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb4f139888 ]
This ensures that the memory mapped by ioremap for adev->rmmio, is
properly handled in amdgpu_device_init(). If the function exits early
due to an error, the memory is unmapped. If the function completes
successfully, the memory remains mapped.
Reported by smatch:
drivers/gpu/drm/amd/amdgpu/amdgpu_device.c:4337 amdgpu_device_init() warn: 'adev->rmmio' from ioremap() not released on lines: 4035,4045,4051,4058,4068,4337
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a5b1521e2 ]
Internal touchscreen on Trogdor Pompom (AKA Dynabook Chromebook C1)
supports USI stylus. Unfortunately the HID descriptor for the stylus
interface does not contain "Stylus" physical collection, which makes
the kernel to try and pull battery information, resulting in errors.
Apply HID_BATTERY_QUIRK_AVOID_QUERY to the device.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c94612a72a ]
I believe RX FIFO depth define 0 is incorrect on Wangxun 10Gb NIC. It
must be at least 1 since code is able to read received data from the
DW_IC_DATA_CMD register.
For now this define is irrelevant since the txgbe_i2c_dw_xfer_quirk()
doesn't use the rx_fifo_depth member variable of struct dw_i2c_dev but
is needed when converting code into generic polling mode implementation.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d8b945fa47 ]
There's issue as follows When do IO fault injection test:
Quota error (device dm-3): find_block_dqentry: Quota for id 101 referenced but not present
Quota error (device dm-3): qtree_read_dquot: Can't read quota structure for id 101
Quota error (device dm-3): do_check_range: Getting block 2021161007 out of range 1-186
Quota error (device dm-3): qtree_read_dquot: Can't read quota structure for id 661
Now, ext4_write_dquot()/ext4_acquire_dquot()/ext4_release_dquot() may commit
inconsistent quota data even if process failed. This may lead to filesystem
corruption.
To ensure filesystem consistent when errors=remount-ro there is need to call
ext4_handle_error() to abort journal.
Signed-off-by: Ye Bin <yebin10@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20240119062908.3598806-1-yebin10@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68ee261fb1 ]
If one group is marked as block bitmap corrupted, its free blocks cannot
be used and its free count is also deducted from the global
sbi->s_freeclusters_counter. User might be confused about the absent
free space because we can't query the information about corrupted block
groups except unreliable error messages in syslog. So add a hint to show
block bitmap corrupted groups in mb_groups.
Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20240119061154.1525781-1-yi.zhang@huaweicloud.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3de49ae81c ]
clang-16 warns about casting incompatible function pointers:
drivers/media/pci/sta2x11/sta2x11_vip.c:1057:6: error: cast from 'irqreturn_t (*)(int, struct sta2x11_vip *)' (aka 'enum irqreturn (*)(int, struct sta2x11_vip *)') to 'irq_handler_t' (aka 'enum irqreturn (*)(int, void *)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
Change the prototype of the irq handler to the regular version with a
local variable to adjust the argument type.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil: update argument documentation]
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2eb52fa890 ]
The context-switch-time check for RCU Tasks Trace quiescence expects
current->trc_reader_special.b.need_qs to be zero, and if so, updates
it to TRC_NEED_QS_CHECKED. This is backwards, because if this value
is zero, there is no RCU Tasks Trace grace period in flight, an thus
no need for a quiescent state. Instead, when a grace period starts,
this field is set to TRC_NEED_QS.
This commit therefore changes the check from zero to TRC_NEED_QS.
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Tested-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4243bf80c7 ]
I have a CD copy of the original Tom Clancy's Ghost Recon game from
2001. The disc mounts without error on Windows, but on Linux mounting
fails with the message "isofs_fill_super: get root inode failed". The
error originates in isofs_read_inode, which returns -EIO because de_len
is 0. The superblock on this disc appears to be intentionally corrupt as
a form of copy protection.
When the root inode is unusable, instead of giving up immediately, try
to continue with the Joliet file table. This fixes the Ghost Recon CD
and probably other copy-protected CDs too.
Signed-off-by: Alex Henrie <alexhenrie24@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Message-Id: <20240208022134.451490-1-alexhenrie24@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f123dc8638 ]
syzbot is reporting sleep in atomic context in SysV filesystem [1], for
sb_bread() is called with rw_spinlock held.
A "write_lock(&pointers_lock) => read_lock(&pointers_lock) deadlock" bug
and a "sb_bread() with write_lock(&pointers_lock)" bug were introduced by
"Replace BKL for chain locking with sysvfs-private rwlock" in Linux 2.5.12.
Then, "[PATCH] err1-40: sysvfs locking fix" in Linux 2.6.8 fixed the
former bug by moving pointers_lock lock to the callers, but instead
introduced a "sb_bread() with read_lock(&pointers_lock)" bug (which made
this problem easier to hit).
Al Viro suggested that why not to do like get_branch()/get_block()/
find_shared() in Minix filesystem does. And doing like that is almost a
revert of "[PATCH] err1-40: sysvfs locking fix" except that get_branch()
from with find_shared() is called without write_lock(&pointers_lock).
Reported-by: syzbot <syzbot+69b40dc5fd40f32c199f@syzkaller.appspotmail.com>
Link: https://syzkaller.appspot.com/bug?extid=69b40dc5fd40f32c199f
Suggested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Link: https://lore.kernel.org/r/0d195f93-a22a-49a2-0020-103534d6f7f6@I-love.SAKURA.ne.jp
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3803584a4e ]
If the number of provided enum IDs in a variable width config register
description does not match the expected number, the checker uses the
expected number for validating the individual enum IDs.
However, this may cause out-of-bounds accesses on the array holding the
enum IDs, leading to bogus enum_id conflict warnings. Worse, if the bug
is an incorrect bit field description (e.g. accidentally using "12"
instead of "-12" for a reserved field), thousands of warnings may be
printed, overflowing the kernel log buffer.
Fix this by limiting the enum ID check to the number of provided enum
IDs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/c7385f44f2faebb8856bcbb4e908d846fc1531fb.1705930809.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 48201a3b3f ]
The ATS2851 controller erroneously reports support for the "Read
Encryption Key Length" HCI command. This makes it unable to connect
to any devices, since this command is issued by the kernel during the
connection process in response to an "Encryption Change" HCI event.
Add a new quirk (HCI_QUIRK_BROKEN_ENC_KEY_SIZE) to hint that the command
is unsupported, preventing it from interrupting the connection process.
This is the error log from btmon before this patch:
> HCI Event: Encryption Change (0x08) plen 4
Status: Success (0x00)
Handle: 2048 Address: ...
Encryption: Enabled with E0 (0x01)
< HCI Command: Read Encryption Key Size (0x05|0x0008) plen 2
Handle: 2048 Address: ...
> HCI Event: Command Status (0x0f) plen 4
Read Encryption Key Size (0x05|0x0008) ncmd 1
Status: Unknown HCI Command (0x01)
Signed-off-by: Vinicius Peixoto <nukelet64@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3e465a07cd ]
Since dracut refers to the module info for defining the required
firmware files and btmtk driver doesn't provide the firmware info for
MT7922, the generate initrd misses the firmware, resulting in the
broken Bluetooth.
This patch simply adds the MODULE_FIRMWARE() for the missing entry
for covering that.
Link: https://bugzilla.suse.com/show_bug.cgi?id=1214133
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11fbb1bfb5 ]
When initializing over virtchnl, the PF is required to pass a VSI ID to the
VF as part of its capabilities exchange. The VF driver reports this value
back to the PF in a variety of commands. The PF driver validates that this
value matches the value it sent to the VF.
Some hardware families such as the E700 series could use this value when
reading RSS registers or communicating directly with firmware over the
Admin Queue.
However, E800 series hardware does not support any of these interfaces and
the VF's only use for this value is to report it back to the PF. Thus,
there is no requirement that this value be an actual VSI ID value of any
kind.
The PF driver already does not trust that the VF sends it a real VSI ID.
The VSI structure is always looked up from the VF structure. The PF does
validate that the VSI ID provided matches a VSI associated with the VF, but
otherwise does not use the VSI ID for any purpose.
Instead of reporting the VSI number relative to the PF space, report a
fixed value of 1. When communicating with the VF over virtchnl, validate
that the VSI number is returned appropriately.
This avoids leaking information about the firmware of the PF state.
Currently the ice driver only supplies a VF with a single VSI. However, it
appears that virtchnl has some support for allowing multiple VSIs. I did
not attempt to implement this. However, space is left open to allow further
relative indexes if additional VSIs are provided in future feature
development. For this reason, keep the ice_vc_isvalid_vsi_id function in
place to allow extending it for multiple VSIs in the future.
This change will also simplify handling of live migration in a future
series. Since we no longer will provide a real VSI number to the VF, there
will be no need to keep track of this number when migrating to a new host.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c6ee34c6f ]
Change BUG_ON to proper error handling if building the path buffer
fails. The pointers are not printed so we don't accidentally leak kernel
addresses.
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26b66d1d36 ]
The get_parent handler looks up a parent of a given dentry, this can be
either a subvolume or a directory. The search is set up with offset -1
but it's never expected to find such item, as it would break allowed
range of inode number or a root id. This means it's a corruption (ext4
also returns this error code).
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7411055db5 ]
The unhandled case in btrfs_relocate_sys_chunks() loop is a corruption,
as it could be caused only by two impossible conditions:
- at first the search key is set up to look for a chunk tree item, with
offset -1, this is an inexact search and the key->offset will contain
the correct offset upon a successful search, a valid chunk tree item
cannot have an offset -1
- after first successful search, the found_key corresponds to a chunk
item, the offset is decremented by 1 before the next loop, it's
impossible to find a chunk item there due to alignment and size
constraints
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd1ebf2467 ]
A common use of type_max() is to find the max for the type of a
variable. Using the pattern type_max(typeof(var)) is needlessly
verbose. Instead, since typeof(type) == type we can just explicitly
call typeof() on the argument to type_max() and type_min(). Add
wrappers for readability.
We can do some replacements right away:
$ git grep '\btype_\(min\|max\)(typeof' | wc -l
11
Link: https://lore.kernel.org/r/20240301062221.work.840-kees@kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4d61a529d ]
Offlining a CPU and bringing it back online is a common operation and it
happens frequently during system suspend/resume, where the non-boot CPUs
are hotplugged out during suspend and brought back at resume.
The cpufreq core already tries to make this path as fast as possible as
the changes are only temporary in nature and full cleanup of resources
isn't required in this case. For example the drivers can implement
online()/offline() callbacks to avoid a lot of tear down of resources.
On similar lines, there is no need to unregister the cpufreq cooling
device during suspend / resume, but only while the policy is getting
removed.
Moreover, unregistering the cpufreq cooling device is resulting in an
unwanted outcome, where the system suspend is eventually aborted in the
process. Currently, during system suspend the cpufreq core unregisters
the cooling device, which in turn removes a kobject using device_del()
and that generates a notification to the userspace via uevent broadcast.
This causes system suspend to abort in some setups.
This was also earlier reported (indirectly) by Roman [1]. Maybe there is
another way around to fixing that problem properly, but this change
makes sense anyways.
Move the registering and unregistering of the cooling device to policy
creation and removal times onlyy.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218521
Reported-by: Manaf Meethalavalappu Pallikunhi <quic_manafm@quicinc.com>
Reported-by: Roman Stratiienko <r.stratiienko@gmail.com>
Link: https://patchwork.kernel.org/project/linux-pm/patch/20220710164026.541466-1-r.stratiienko@gmail.com/ [1]
Tested-by: Manaf Meethalavalappu Pallikunhi <quic_manafm@quicinc.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1cca1bddf9 ]
Currently buf_len field of ath11k_mhi_config_qca6390 is assigned
with 0, making MHI use a default size, 64KB, to allocate channel
buffers. This is likely to fail in some scenarios where system
memory is highly fragmented and memory compaction or reclaim is
not allowed.
There is a fail report which is caused by it:
kworker/u32:45: page allocation failure: order:4, mode:0x40c00(GFP_NOIO|__GFP_COMP), nodemask=(null),cpuset=/,mems_allowed=0
CPU: 0 PID: 19318 Comm: kworker/u32:45 Not tainted 6.8.0-rc3-1.gae4495f-default #1 openSUSE Tumbleweed (unreleased) 493b6d5b382c603654d7a81fc3c144d59a1dfceb
Workqueue: events_unbound async_run_entry_fn
Call Trace:
<TASK>
dump_stack_lvl+0x47/0x60
warn_alloc+0x13a/0x1b0
? srso_alias_return_thunk+0x5/0xfbef5
? __alloc_pages_direct_compact+0xab/0x210
__alloc_pages_slowpath.constprop.0+0xd3e/0xda0
__alloc_pages+0x32d/0x350
? mhi_prepare_channel+0x127/0x2d0 [mhi 40df44e07c05479f7a6e7b90fba9f0e0031a7814]
__kmalloc_large_node+0x72/0x110
__kmalloc+0x37c/0x480
? mhi_map_single_no_bb+0x77/0xf0 [mhi 40df44e07c05479f7a6e7b90fba9f0e0031a7814]
? mhi_prepare_channel+0x127/0x2d0 [mhi 40df44e07c05479f7a6e7b90fba9f0e0031a7814]
mhi_prepare_channel+0x127/0x2d0 [mhi 40df44e07c05479f7a6e7b90fba9f0e0031a7814]
__mhi_prepare_for_transfer+0x44/0x80 [mhi 40df44e07c05479f7a6e7b90fba9f0e0031a7814]
? __pfx_____mhi_prepare_for_transfer+0x10/0x10 [mhi 40df44e07c05479f7a6e7b90fba9f0e0031a7814]
device_for_each_child+0x5c/0xa0
? __pfx_pci_pm_resume+0x10/0x10
ath11k_core_resume+0x65/0x100 [ath11k a5094e22d7223135c40d93c8f5321cf09fd85e4e]
? srso_alias_return_thunk+0x5/0xfbef5
ath11k_pci_pm_resume+0x32/0x60 [ath11k_pci 830b7bfc3ea80ebef32e563cafe2cb55e9cc73ec]
? srso_alias_return_thunk+0x5/0xfbef5
dpm_run_callback+0x8c/0x1e0
device_resume+0x104/0x340
? __pfx_dpm_watchdog_handler+0x10/0x10
async_resume+0x1d/0x30
async_run_entry_fn+0x32/0x120
process_one_work+0x168/0x330
worker_thread+0x2f5/0x410
? __pfx_worker_thread+0x10/0x10
kthread+0xe8/0x120
? __pfx_kthread+0x10/0x10
ret_from_fork+0x34/0x50
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1b/0x30
</TASK>
Actually those buffers are used only by QMI target -> host communication.
And for WCN6855 and QCA6390, the largest packet size for that is less
than 6KB. So change buf_len field to 8KB, which results in order 1
allocation if page size is 4KB. In this way, we can at least save some
memory, and as well as decrease the possibility of allocation failure
in those scenarios.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Reported-by: Vlastimil Babka <vbabka@suse.cz>
Closes: https://lore.kernel.org/ath11k/96481a45-3547-4d23-ad34-3a8f1d90c1cd@suse.cz/
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240223053111.29170-1-quic_bqiang@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b9fa16949d ]
On TDX it is possible for the untrusted host to cause
set_memory_encrypted() or set_memory_decrypted() to fail such that an
error is returned and the resulting memory is shared. Callers need to
take care to handle these errors to avoid returning decrypted (shared)
memory to the page allocator, which could lead to functional or security
issues.
DMA could free decrypted/shared pages if dma_set_decrypted() fails. This
should be a rare case. Just leak the pages in this case instead of
freeing them.
Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f5151005d3 ]
In particular the xpcs_soft_reset() and xpcs_do_config() functions
currently return -1 if invalid auto-negotiation mode is specified. That
value might be then passed to the generic kernel subsystems which require
a standard kernel errno value. Even though the erroneous conditions are
very specific (memory corruption or buggy driver implementation) using a
hard-coded -1 literal doesn't seem correct anyway especially when it comes
to passing it higher to the network subsystem or printing to the system
log. Convert the hard-coded error values to -EINVAL then.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f85450f134 ]
In function get_pkg_num() if fopen_or_die() succeeds it returns a file
pointer to be used. But fclose() is never called before returning from
the function.
Signed-off-by: Samasth Norway Ananda <samasth.norway.ananda@oracle.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c86e17455 ]
Some recent(ish) Dell AIO devices have a backlight controller board
connected to an UART.
This UART has a DELL0501 HID with CID set to PNP0501 so that the UART is
still handled by 8250_pnp.c. Unfortunately there is no separate ACPI device
with an UartSerialBusV2() resource to model the backlight-controller.
The next patch in this series will use acpi_quirk_skip_serdev_enumeration()
to still create a serdev for this for a backlight driver to bind to
instead of creating a /dev/ttyS0.
This new acpi_quirk_skip_serdev_enumeration() use is not limited to Android
X86 tablets, so move it out of the ifdef CONFIG_X86_ANDROID_TABLETS block.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3687854d3e ]
A race condition was observed when accessing mapped registers, so add
locking to protect against concurrent access.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0937f95ab0 ]
Sicne the mapping is global, mapped register access needs to be protected
against concurrent access, otherwise a race condition might cause the reads
or writes to go towards the wrong register
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 32167707aa ]
The ACEPC W5 Pro HDMI stick contains quite generic names in the sys_vendor
and product_name DMI strings, without this patch brcmfmac will try to load:
"brcmfmac43455-sdio.$(DEFAULT_STRING)-$(DEFAULT_STRING).txt" as nvram file
which is both too generic and messy with the $ symbols in the name.
The ACEPC W5 Pro uses the same Ampak AP6255 module as the ACEPC T8
and the nvram for the T8 is already in linux-firmware, so point the new
DMI nvram filename quirk to the T8 nvram file.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240216213649.251718-1-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1315848f1f ]
The kfree() function was called in one case by
the get_filename() function during error handling
even if the passed variable contained a null pointer.
This issue was detected by using the Coccinelle software.
Thus return directly after a call of the function “kzalloc” failed
at the beginning.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 219eee9c0d ]
syzbot managed to trigger following splat:
BUG: KASAN: use-after-free in __skb_flow_dissect+0x4a3b/0x5e50
Read of size 1 at addr ffff888208a4000e by task a.out/2313
[..]
__skb_flow_dissect+0x4a3b/0x5e50
__skb_get_hash+0xb4/0x400
ip_tunnel_xmit+0x77e/0x26f0
ipip_tunnel_xmit+0x298/0x410
..
Analysis shows that the skb has a valid ->head, but bogus ->data
pointer.
skb->data gets its bogus value via the neigh layer, which does:
1556 __skb_pull(skb, skb_network_offset(skb));
... and the skb was already dodgy at this point:
skb_network_offset(skb) returns a negative value due to an
earlier overflow of skb->network_header (u16). __skb_pull thus
"adjusts" skb->data by a huge offset, pointing outside skb->head
area.
Allow debug builds to splat when we try to pull/push more than
INT_MAX bytes.
After this, the syzkaller reproducer yields a more precise splat
before the flow dissector attempts to read off skb->data memory:
WARNING: CPU: 5 PID: 2313 at include/linux/skbuff.h:2653 neigh_connected_output+0x28e/0x400
ip_finish_output2+0xb25/0xed0
iptunnel_xmit+0x4ff/0x870
ipgre_xmit+0x78e/0xbb0
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240216113700.23013-1-fw@strlen.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 697624ee8a ]
According to i.MX8MP RM and HDMI ADD, the fdcc clock is part of
hdmi rx verification IP that should not enable for HDMI TX.
But actually if the clock is disabled before HDMI/LCDIF probe,
LCDIF will not get pixel clock from HDMI PHY and print the error
logs:
[CRTC:39:crtc-2] vblank wait timed out
WARNING: CPU: 2 PID: 9 at drivers/gpu/drm/drm_atomic_helper.c:1634 drm_atomic_helper_wait_for_vblanks.part.0+0x23c/0x260
Add fdcc clock to LCDIF and HDMI TX power domains to fix the issue.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Sandor Yu <Sandor.yu@nxp.com>
Link: https://lore.kernel.org/r/20240203165307.7806-5-aford173@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 88390dd788 ]
In detail:
In C language, when you perform a multiplication operation, if
both operands are of int type, the multiplication operation is
performed on the int type, and then the result is converted to
the target type. This means that if the product of int type
multiplication exceeds the range that int type can represent,
an overflow will occur even if you store the result in a
variable of int64_t type.
For a multiplication of two int values, it is better to use
mul_u32_u32() rather than s->exit_latency_ns = s->exit_latency *
NSEC_PER_USEC to avoid potential overflow happenning.
Signed-off-by: C Cheng <C.Cheng@mediatek.com>
Signed-off-by: Bo Ye <bo.ye@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
[ rjw: New subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d988d9a9b9 ]
If the kernel crashes in a context where printk() calls always
defer printing (such as in NMI or inside a printk_safe section)
then the final panic messages will be deferred to irq_work. But
if irq_work is not available, the messages will not get printed
unless explicitly flushed. The result is that the final
"end Kernel panic" banner does not get printed.
Add one final flush after the last printk() call to make sure
the final panic messages make it out as well.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20240207134103.1357162-14-john.ogness@linutronix.de
Signed-off-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ab7cdd004 ]
Currently @suppress_panic_printk is checked along with
non-matching @panic_cpu and current CPU. This works
because @suppress_panic_printk is only set when
panic_in_progress() is true.
Rather than relying on the @suppress_panic_printk semantics,
use the concise helper function other_cpu_in_progress(). The
helper function exists to avoid open coding such tests.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20240207134103.1357162-7-john.ogness@linutronix.de
Signed-off-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 19b070fefd ]
Syzkaller hit 'WARNING in dg_dispatch_as_host' bug.
memcpy: detected field-spanning write (size 56) of single field "&dg_info->msg"
at drivers/misc/vmw_vmci/vmci_datagram.c:237 (size 24)
WARNING: CPU: 0 PID: 1555 at drivers/misc/vmw_vmci/vmci_datagram.c:237
dg_dispatch_as_host+0x88e/0xa60 drivers/misc/vmw_vmci/vmci_datagram.c:237
Some code commentry, based on my understanding:
544 #define VMCI_DG_SIZE(_dg) (VMCI_DG_HEADERSIZE + (size_t)(_dg)->payload_size)
/// This is 24 + payload_size
memcpy(&dg_info->msg, dg, dg_size);
Destination = dg_info->msg ---> this is a 24 byte
structure(struct vmci_datagram)
Source = dg --> this is a 24 byte structure (struct vmci_datagram)
Size = dg_size = 24 + payload_size
{payload_size = 56-24 =32} -- Syzkaller managed to set payload_size to 32.
35 struct delayed_datagram_info {
36 struct datagram_entry *entry;
37 struct work_struct work;
38 bool in_dg_host_queue;
39 /* msg and msg_payload must be together. */
40 struct vmci_datagram msg;
41 u8 msg_payload[];
42 };
So those extra bytes of payload are copied into msg_payload[], a run time
warning is seen while fuzzing with Syzkaller.
One possible way to fix the warning is to split the memcpy() into
two parts -- one -- direct assignment of msg and second taking care of payload.
Gustavo quoted:
"Under FORTIFY_SOURCE we should not copy data across multiple members
in a structure."
Reported-by: syzkaller <syzkaller@googlegroups.com>
Suggested-by: Vegard Nossum <vegard.nossum@oracle.com>
Suggested-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/20240105164001.2129796-2-harshit.m.mogalapalli@oracle.com
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c108b4a50d ]
Hardware puts RX descriptor and packet in RX DMA buffer, so it could be
over one buffer size if packet size is 11454, and then it will be split
into two segments. WiFi 7 chips use larger size of RX descriptor, so
enlarge DMA buffer size according to RX descriptor to have better
performance and simple flow.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240121071826.10159-5-pkshih@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5642c82b94 ]
A potential string truncation was reported in bnx2x_fill_fw_str(),
when a long bp->fw_ver and a long phy_fw_ver might coexist, but seems
unlikely with real-world hardware.
Use scnprintf() to indicate the intent that truncations are tolerated.
While reading this code, I found a collection of various buffer size
counting issues. None looked like they might lead to a buffer overflow
with current code (the small buffers are 20 bytes and might only ever
consume 10 bytes twice with a trailing %NUL). However, early truncation
(due to a %NUL in the middle of the string) might be happening under
likely rare conditions. Regardless fix the formatters and related
functions:
- Switch from a separate strscpy() to just adding an additional "%s" to
the format string that immediately follows it in bnx2x_fill_fw_str().
- Use sizeof() universally instead of using unbound defines.
- Fix bnx2x_7101_format_ver() and bnx2x_null_format_ver() to report the
number of characters written, not including the trailing %NUL (as
already done with the other firmware formatting functions).
- Require space for at least 1 byte in bnx2x_get_ext_phy_fw_version()
for the trailing %NUL.
- Correct the needed buffer size in bnx2x_3_seq_format_ver().
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202401260858.jZN6vD1k-lkp@intel.com/
Cc: Ariel Elior <aelior@marvell.com>
Cc: Sudarsana Kalluru <skalluru@marvell.com>
Cc: Manish Chopra <manishc@marvell.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20240126041044.work.220-kees@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
CI builds are done with debug info disabled, but this removes some
members from struct module. This causes builds to fail if there is an
ABI reference for the current ABI.
Define these members unconditionally, so that there is no ABI change.
commit 95a6ccbdc7 upstream.
BHI mitigation mode spectre_bhi=auto does not deploy the software
mitigation by default. In a cloud environment, it is a likely scenario
where userspace is trusted but the guests are not trusted. Deploying
system wide mitigation in such cases is not desirable.
Update the auto mode to unconditionally mitigate against malicious
guests. Deploy the software sequence at VMexit in auto mode also, when
hardware mitigation is not available. Unlike the force =on mode,
software sequence is not deployed at syscalls in auto mode.
Suggested-by: Alexandre Chartre <alexandre.chartre@oracle.com>
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Daniel Sneddon <daniel.sneddon@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexandre Chartre <alexandre.chartre@oracle.com>
Reviewed-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Daniel Sneddon <daniel.sneddon@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ec9404e40e upstream.
Branch history clearing software sequences and hardware control
BHI_DIS_S were defined to mitigate Branch History Injection (BHI).
Add cmdline spectre_bhi={on|off|auto} to control BHI mitigation:
auto - Deploy the hardware mitigation BHI_DIS_S, if available.
on - Deploy the hardware mitigation BHI_DIS_S, if available,
otherwise deploy the software sequence at syscall entry and
VMexit.
off - Turn off BHI mitigation.
The default is auto mode which does not deploy the software sequence
mitigation. This is because of the hardening done in the syscall
dispatch path, which is the likely target of BHI.
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Daniel Sneddon <daniel.sneddon@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexandre Chartre <alexandre.chartre@oracle.com>
Reviewed-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Daniel Sneddon <daniel.sneddon@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7390db8aea upstream.
Branch History Injection (BHI) attacks may allow a malicious application to
influence indirect branch prediction in kernel by poisoning the branch
history. eIBRS isolates indirect branch targets in ring0. The BHB can
still influence the choice of indirect branch predictor entry, and although
branch predictor entries are isolated between modes when eIBRS is enabled,
the BHB itself is not isolated between modes.
Alder Lake and new processors supports a hardware control BHI_DIS_S to
mitigate BHI. For older processors Intel has released a software sequence
to clear the branch history on parts that don't support BHI_DIS_S. Add
support to execute the software sequence at syscall entry and VMexit to
overwrite the branch history.
For now, branch history is not cleared at interrupt entry, as malicious
applications are not believed to have sufficient control over the
registers, since previous register state is cleared at interrupt
entry. Researchers continue to poke at this area and it may become
necessary to clear at interrupt entry as well in the future.
This mitigation is only defined here. It is enabled later.
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Co-developed-by: Daniel Sneddon <daniel.sneddon@linux.intel.com>
Signed-off-by: Daniel Sneddon <daniel.sneddon@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexandre Chartre <alexandre.chartre@oracle.com>
Reviewed-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Daniel Sneddon <daniel.sneddon@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1e3ad78334 upstream.
Make <asm/syscall.h> build a switch statement instead, and the compiler can
either decide to generate an indirect jump, or - more likely these days due
to mitigations - just a series of conditional branches.
Yes, the conditional branches also have branch prediction, but the branch
prediction is much more controlled, in that it just causes speculatively
running the wrong system call (harmless), rather than speculatively running
possibly wrong random less controlled code gadgets.
This doesn't mitigate other indirect calls, but the system call indirection
is the first and most easily triggered case.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Daniel Sneddon <daniel.sneddon@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Daniel Sneddon <daniel.sneddon@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd0d9d92c8 upstream.
The early SME/SEV code parses the command line very early, in order to
decide whether or not memory encryption should be enabled, which needs
to occur even before the initial page tables are created.
This is problematic for a number of reasons:
- this early code runs from the 1:1 mapping provided by the decompressor
or firmware, which uses a different translation than the one assumed by
the linker, and so the code needs to be built in a special way;
- parsing external input while the entire kernel image is still mapped
writable is a bad idea in general, and really does not belong in
security minded code;
- the current code ignores the built-in command line entirely (although
this appears to be the case for the entire decompressor)
Given that the decompressor/EFI stub is an intrinsic part of the x86
bootable kernel image, move the command line parsing there and out of
the core kernel. This removes the need to build lib/cmdline.o in a
special way, or to use RIP-relative LEA instructions in inline asm
blocks.
This involves a new xloadflag in the setup header to indicate
that mem_encrypt=on appeared on the kernel command line.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lore.kernel.org/r/20240227151907.387873-17-ardb+git@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9c55461040 upstream.
Currently, the EFI stub invokes the EFI memory attributes protocol to
strip any NX restrictions from the entire loaded kernel, resulting in
all code and data being mapped read-write-execute.
The point of the EFI memory attributes protocol is to remove the need
for all memory allocations to be mapped with both write and execute
permissions by default, and make it the OS loader's responsibility to
transition data mappings to code mappings where appropriate.
Even though the UEFI specification does not appear to leave room for
denying memory attribute changes based on security policy, let's be
cautious and avoid relying on the ability to create read-write-execute
mappings. This is trivially achievable, given that the amount of kernel
code executing via the firmware's 1:1 mapping is rather small and
limited to the .head.text region. So let's drop the NX restrictions only
on that subregion, but not before remapping it as read-only first.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 48204aba80 upstream.
The .head.text section is the initial primary entrypoint of the core
kernel, and is entered with the CPU executing from a 1:1 mapping of
memory. Such code must never access global variables using absolute
references, as these are based on the kernel virtual mapping which is
not active yet at this point.
Given that the SME startup code is also called from this early execution
context, move it into .head.text as well. This will allow more thorough
build time checks in the future to ensure that early startup code only
uses RIP-relative references to global variables.
Also replace some occurrences of __pa_symbol() [which relies on the
compiler generating an absolute reference, which is not guaranteed] and
an open coded RIP-relative access with RIP_REL_REF().
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lore.kernel.org/r/20240227151907.387873-18-ardb+git@google.com
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a80dbcb2d upstream.
BPF link for some program types is passed as a "context" which can be
used by those BPF programs to look up additional information. E.g., for
multi-kprobes and multi-uprobes, link is used to fetch BPF cookie values.
Because of this runtime dependency, when bpf_link refcnt drops to zero
there could still be active BPF programs running accessing link data.
This patch adds generic support to defer bpf_link dealloc callback to
after RCU GP, if requested. This is done by exposing two different
deallocation callbacks, one synchronous and one deferred. If deferred
one is provided, bpf_link_free() will schedule dealloc_deferred()
callback to happen after RCU GP.
BPF is using two flavors of RCU: "classic" non-sleepable one and RCU
tasks trace one. The latter is used when sleepable BPF programs are
used. bpf_link_free() accommodates that by checking underlying BPF
program's sleepable flag, and goes either through normal RCU GP only for
non-sleepable, or through RCU tasks trace GP *and* then normal RCU GP
(taking into account rcu_trace_implies_rcu_gp() optimization), if BPF
program is sleepable.
We use this for multi-kprobe and multi-uprobe links, which dereference
link during program run. We also preventively switch raw_tp link to use
deferred dealloc callback, as upcoming changes in bpf-next tree expose
raw_tp link data (specifically, cookie value) to BPF program at runtime
as well.
Fixes: 0dcac27254 ("bpf: Add multi kprobe link")
Fixes: 89ae89f53d ("bpf: Add multi uprobe link")
Reported-by: syzbot+981935d9485a560bfbcb@syzkaller.appspotmail.com
Reported-by: syzbot+2cb5a6c573e98db598cc@syzkaller.appspotmail.com
Reported-by: syzbot+62d8b26793e8a2bd0516@syzkaller.appspotmail.com
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/r/20240328052426.3042617-2-andrii@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9c856cabe upstream.
There is no need to delay putting either path or task to deallocation
step. It can be done right after bpf_uprobe_unregister. Between release
and dealloc, there could be still some running BPF programs, but they
don't access either task or path, only data in link->uprobes, so it is
safe to do.
On the other hand, doing path_put() in dealloc callback makes this
dealloc sleepable because path_put() itself might sleep. Which is
problematic due to the need to call uprobe's dealloc through call_rcu(),
which is what is done in the next bug fix patch. So solve the problem by
releasing these resources early.
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/r/20240328052426.3042617-1-andrii@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e2b8a9fa5 upstream.
Eric Dumazet suggests:
> The fact that mptcp_is_tcpsk() was able to write over sock->ops was a
> bit strange to me.
> mptcp_is_tcpsk() should answer a question, with a read-only argument.
re-factor code to avoid overwriting sock_ops inside that function. Also,
change the helper name to reflect the semantics and to disambiguate from
its dual, sk_is_mptcp(). While at it, collapse mptcp_stream_accept() and
mptcp_accept() into a single function, where fallback / non-fallback are
separated into a single sk_is_mptcp() conditional.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/432
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Matthieu Baerts <matttbe@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e3aae1098f upstream.
shellcheck recently helped to prevent issues. It is then good to fix the
other harmless issues in order to spot "real" ones later.
Here, two categories of warnings are now ignored:
- SC2317: Command appears to be unreachable. The cleanup() function is
invoked indirectly via the EXIT trap.
- SC2086: Double quote to prevent globbing and word splitting. This is
recommended, but the current usage is correct and there is no need to
do all these modifications to be compliant with this rule.
For the modifications:
- SC2034: ksft_skip appears unused.
- SC2181: Check exit code directly with e.g. 'if mycmd;', not
indirectly with $?.
- SC2004: $/${} is unnecessary on arithmetic variables.
- SC2155: Declare and assign separately to avoid masking return
values.
- SC2166: Prefer [ p ] && [ q ] as [ p -a q ] is not well defined.
- SC2059: Don't use variables in the printf format string. Use printf
'..%s..' "$foo".
Now this script is shellcheck (0.9.0) compliant. We can easily spot new
issues.
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://lore.kernel.org/r/20240306-upstream-net-next-20240304-selftests-mptcp-shared-code-shellcheck-v2-8-bc79e6e5e6a0@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a1aa5390cc upstream.
In of_modalias(), we can get passed the str and len parameters which would
cause a kernel oops in vsnprintf() since it only allows passing a NULL ptr
when the length is also 0. Also, we need to filter out the negative values
of the len parameter as these will result in a really huge buffer since
snprintf() takes size_t parameter while ours is ssize_t...
Found by Linux Verification Center (linuxtesting.org) with the Svace static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1d211023-3923-685b-20f0-f3f90ea56e1f@omp.ru
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 173217bd73 upstream.
In the current implementation, CIFS close sends a close to the
server and does not check for the success of the server close.
This patch adds functionality to check for server close return
status and retries in case of an EBUSY or EAGAIN error.
This can help avoid handle leaks
Cc: stable@vger.kernel.org
Signed-off-by: Ritvik Budhiraja <rbudhiraja@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d14fa1fcf6 upstream.
childregs represents the registers which are active for the new thread
in user context. For a kernel thread, childregs->gp is never used since
the kernel gp is not touched by switch_to. For a user mode helper, the
gp value can be observed in user space after execve or possibly by other
means.
[From the email thread]
The /* Kernel thread */ comment is somewhat inaccurate in that it is also used
for user_mode_helper threads, which exec a user process, e.g. /sbin/init or
when /proc/sys/kernel/core_pattern is a pipe. Such threads do not have
PF_KTHREAD set and are valid targets for ptrace etc. even before they exec.
childregs is the *user* context during syscall execution and it is observable
from userspace in at least five ways:
1. kernel_execve does not currently clear integer registers, so the starting
register state for PID 1 and other user processes started by the kernel has
sp = user stack, gp = kernel __global_pointer$, all other integer registers
zeroed by the memset in the patch comment.
This is a bug in its own right, but I'm unwilling to bet that it is the only
way to exploit the issue addressed by this patch.
2. ptrace(PTRACE_GETREGSET): you can PTRACE_ATTACH to a user_mode_helper thread
before it execs, but ptrace requires SIGSTOP to be delivered which can only
happen at user/kernel boundaries.
3. /proc/*/task/*/syscall: this is perfectly happy to read pt_regs for
user_mode_helpers before the exec completes, but gp is not one of the
registers it returns.
4. PERF_SAMPLE_REGS_USER: LOCKDOWN_PERF normally prevents access to kernel
addresses via PERF_SAMPLE_REGS_INTR, but due to this bug kernel addresses
are also exposed via PERF_SAMPLE_REGS_USER which is permitted under
LOCKDOWN_PERF. I have not attempted to write exploit code.
5. Much of the tracing infrastructure allows access to user registers. I have
not attempted to determine which forms of tracing allow access to user
registers without already allowing access to kernel registers.
Fixes: 7db91e57a0 ("RISC-V: Task implementation")
Cc: stable@vger.kernel.org
Signed-off-by: Stefan O'Rear <sorear@fastmail.com>
Reviewed-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Link: https://lore.kernel.org/r/20240327061258.2370291-1-sorear@fastmail.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 65291dcfcf upstream.
folio_is_secretmem() currently relies on secretmem folios being LRU
folios, to save some cycles.
However, folios might reside in a folio batch without the LRU flag set, or
temporarily have their LRU flag cleared. Consequently, the LRU flag is
unreliable for this purpose.
In particular, this is the case when secretmem_fault() allocates a fresh
page and calls filemap_add_folio()->folio_add_lru(). The folio might be
added to the per-cpu folio batch and won't get the LRU flag set until the
batch was drained using e.g., lru_add_drain().
Consequently, folio_is_secretmem() might not detect secretmem folios and
GUP-fast can succeed in grabbing a secretmem folio, crashing the kernel
when we would later try reading/writing to the folio, because the folio
has been unmapped from the directmap.
Fix it by removing that unreliable check.
Link: https://lkml.kernel.org/r/20240326143210.291116-2-david@redhat.com
Fixes: 1507f51255 ("mm: introduce memfd_secret system call to create "secret" memory areas")
Signed-off-by: David Hildenbrand <david@redhat.com>
Reported-by: xingwei lee <xrivendell7@gmail.com>
Reported-by: yue sun <samsun1006219@gmail.com>
Closes: https://lore.kernel.org/lkml/CABOYnLyevJeravW=QrH0JUPYEcDN160aZFb7kwndm-J2rmz0HQ@mail.gmail.com/
Debugged-by: Miklos Szeredi <miklos@szeredi.hu>
Tested-by: Miklos Szeredi <mszeredi@redhat.com>
Reviewed-by: Mike Rapoport (IBM) <rppt@kernel.org>
Cc: Lorenzo Stoakes <lstoakes@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b017a0cea6 upstream.
The SVE register sets have two different formats, one of which is a wrapped
version of the standard FPSIMD register set and another with actual SVE
register data. At present we check TIF_SVE to see if full SVE register
state should be provided when reading the SVE regset but if we were in a
syscall we may have saved only floating point registers even though that is
set.
Fix this and simplify the logic by checking and using the format which we
recorded when deciding if we should use FPSIMD or SVE format.
Fixes: 8c845e2731 ("arm64/sve: Leave SVE enabled on syscall if we don't context switch")
Cc: <stable@vger.kernel.org> # 6.2.x
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20240325-arm64-ptrace-fp-type-v1-1-8dc846caf11f@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 312be9fc22 upstream.
The MSR_PEBS_DATA_CFG MSR register is used to configure which data groups
should be generated into a PEBS record, and it's shared among all counters.
If there are different configurations among counters, perf combines all the
configurations.
The first perf command as below requires a complete PEBS record
(including memory info, GPRs, XMMs, and LBRs). The second perf command
only requires a basic group. However, after the second perf command is
running, the MSR_PEBS_DATA_CFG register is cleared. Only a basic group is
generated in a PEBS record, which is wrong. The required information
for the first perf command is missed.
$ perf record --intr-regs=AX,SP,XMM0 -a -C 8 -b -W -d -c 100000003 -o /dev/null -e cpu/event=0xd0,umask=0x81/upp &
$ sleep 5
$ perf record --per-thread -c 1 -e cycles:pp --no-timestamp --no-tid taskset -c 8 ./noploop 1000
The first PEBS event is a system-wide PEBS event. The second PEBS event
is a per-thread event. When the thread is scheduled out, the
intel_pmu_pebs_del() function is invoked to update the PEBS state.
Since the system-wide event is still available, the cpuc->n_pebs is 1.
The cpuc->pebs_data_cfg is cleared. The data configuration for the
system-wide PEBS event is lost.
The (cpuc->n_pebs == 1) check was introduced in commit:
b6a32f023f ("perf/x86: Fix PEBS threshold initialization")
At that time, it indeed didn't hurt whether the state was updated
during the removal, because only the threshold is updated.
The calculation of the threshold takes the last PEBS event into
account.
However, since commit:
b752ea0c28 ("perf/x86/intel/ds: Flush PEBS DS when changing PEBS_DATA_CFG")
we delay the threshold update, and clear the PEBS data config, which triggers
the bug.
The PEBS data config update scope should not be shrunk during removal.
[ mingo: Improved the changelog & comments. ]
Fixes: b752ea0c28 ("perf/x86/intel/ds: Flush PEBS DS when changing PEBS_DATA_CFG")
Reported-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240401133320.703971-1-kan.liang@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 99485c4c02 upstream.
There are few uses of CoCo that don't rely on working cryptography and
hence a working RNG. Unfortunately, the CoCo threat model means that the
VM host cannot be trusted and may actively work against guests to
extract secrets or manipulate computation. Since a malicious host can
modify or observe nearly all inputs to guests, the only remaining source
of entropy for CoCo guests is RDRAND.
If RDRAND is broken -- due to CPU hardware fault -- the RNG as a whole
is meant to gracefully continue on gathering entropy from other sources,
but since there aren't other sources on CoCo, this is catastrophic.
This is mostly a concern at boot time when initially seeding the RNG, as
after that the consequences of a broken RDRAND are much more
theoretical.
So, try at boot to seed the RNG using 256 bits of RDRAND output. If this
fails, panic(). This will also trigger if the system is booted without
RDRAND, as RDRAND is essential for a safe CoCo boot.
Add this deliberately to be "just a CoCo x86 driver feature" and not
part of the RNG itself. Many device drivers and platforms have some
desire to contribute something to the RNG, and add_device_randomness()
is specifically meant for this purpose.
Any driver can call it with seed data of any quality, or even garbage
quality, and it can only possibly make the quality of the RNG better or
have no effect, but can never make it worse.
Rather than trying to build something into the core of the RNG, consider
the particular CoCo issue just a CoCo issue, and therefore separate it
all out into driver (well, arch/platform) code.
[ bp: Massage commit message. ]
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Elena Reshetova <elena.reshetova@intel.com>
Reviewed-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240326160735.73531-1-Jason@zx2c4.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ddf944b32 upstream.
Modifying a MCA bank's MCA_CTL bits which control which error types to
be reported is done over
/sys/devices/system/machinecheck/
├── machinecheck0
│ ├── bank0
│ ├── bank1
│ ├── bank10
│ ├── bank11
...
sysfs nodes by writing the new bit mask of events to enable.
When the write is accepted, the kernel deletes all current timers and
reinits all banks.
Doing that in parallel can lead to initializing a timer which is already
armed and in the timer wheel, i.e., in use already:
ODEBUG: init active (active state 0) object: ffff888063a28000 object
type: timer_list hint: mce_timer_fn+0x0/0x240 arch/x86/kernel/cpu/mce/core.c:2642
WARNING: CPU: 0 PID: 8120 at lib/debugobjects.c:514
debug_print_object+0x1a0/0x2a0 lib/debugobjects.c:514
Fix that by grabbing the sysfs mutex as the rest of the MCA sysfs code
does.
Reported by: Yue Sun <samsun1006219@gmail.com>
Reported by: xingwei lee <xrivendell7@gmail.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Cc: <stable@kernel.org>
Link: https://lore.kernel.org/r/CAEkJfYNiENwQY8yV1LYJ9LjJs%2Bx_-PqMv98gKig55=2vbzffRw@mail.gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 04c35ab3bd upstream.
PAT handling won't do the right thing in COW mappings: the first PTE (or,
in fact, all PTEs) can be replaced during write faults to point at anon
folios. Reliably recovering the correct PFN and cachemode using
follow_phys() from PTEs will not work in COW mappings.
Using follow_phys(), we might just get the address+protection of the anon
folio (which is very wrong), or fail on swap/nonswap entries, failing
follow_phys() and triggering a WARN_ON_ONCE() in untrack_pfn() and
track_pfn_copy(), not properly calling free_pfn_range().
In free_pfn_range(), we either wouldn't call memtype_free() or would call
it with the wrong range, possibly leaking memory.
To fix that, let's update follow_phys() to refuse returning anon folios,
and fallback to using the stored PFN inside vma->vm_pgoff for COW mappings
if we run into that.
We will now properly handle untrack_pfn() with COW mappings, where we
don't need the cachemode. We'll have to fail fork()->track_pfn_copy() if
the first page was replaced by an anon folio, though: we'd have to store
the cachemode in the VMA to make this work, likely growing the VMA size.
For now, lets keep it simple and let track_pfn_copy() just fail in that
case: it would have failed in the past with swap/nonswap entries already,
and it would have done the wrong thing with anon folios.
Simple reproducer to trigger the WARN_ON_ONCE() in untrack_pfn():
<--- C reproducer --->
#include <stdio.h>
#include <sys/mman.h>
#include <unistd.h>
#include <liburing.h>
int main(void)
{
struct io_uring_params p = {};
int ring_fd;
size_t size;
char *map;
ring_fd = io_uring_setup(1, &p);
if (ring_fd < 0) {
perror("io_uring_setup");
return 1;
}
size = p.sq_off.array + p.sq_entries * sizeof(unsigned);
/* Map the submission queue ring MAP_PRIVATE */
map = mmap(0, size, PROT_READ | PROT_WRITE, MAP_PRIVATE,
ring_fd, IORING_OFF_SQ_RING);
if (map == MAP_FAILED) {
perror("mmap");
return 1;
}
/* We have at least one page. Let's COW it. */
*map = 0;
pause();
return 0;
}
<--- C reproducer --->
On a system with 16 GiB RAM and swap configured:
# ./iouring &
# memhog 16G
# killall iouring
[ 301.552930] ------------[ cut here ]------------
[ 301.553285] WARNING: CPU: 7 PID: 1402 at arch/x86/mm/pat/memtype.c:1060 untrack_pfn+0xf4/0x100
[ 301.553989] Modules linked in: binfmt_misc nft_fib_inet nft_fib_ipv4 nft_fib_ipv6 nft_fib nft_reject_g
[ 301.558232] CPU: 7 PID: 1402 Comm: iouring Not tainted 6.7.5-100.fc38.x86_64 #1
[ 301.558772] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.16.3-0-ga6ed6b701f0a-prebu4
[ 301.559569] RIP: 0010:untrack_pfn+0xf4/0x100
[ 301.559893] Code: 75 c4 eb cf 48 8b 43 10 8b a8 e8 00 00 00 3b 6b 28 74 b8 48 8b 7b 30 e8 ea 1a f7 000
[ 301.561189] RSP: 0018:ffffba2c0377fab8 EFLAGS: 00010282
[ 301.561590] RAX: 00000000ffffffea RBX: ffff9208c8ce9cc0 RCX: 000000010455e047
[ 301.562105] RDX: 07fffffff0eb1e0a RSI: 0000000000000000 RDI: ffff9208c391d200
[ 301.562628] RBP: 0000000000000000 R08: ffffba2c0377fab8 R09: 0000000000000000
[ 301.563145] R10: ffff9208d2292d50 R11: 0000000000000002 R12: 00007fea890e0000
[ 301.563669] R13: 0000000000000000 R14: ffffba2c0377fc08 R15: 0000000000000000
[ 301.564186] FS: 0000000000000000(0000) GS:ffff920c2fbc0000(0000) knlGS:0000000000000000
[ 301.564773] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 301.565197] CR2: 00007fea88ee8a20 CR3: 00000001033a8000 CR4: 0000000000750ef0
[ 301.565725] PKRU: 55555554
[ 301.565944] Call Trace:
[ 301.566148] <TASK>
[ 301.566325] ? untrack_pfn+0xf4/0x100
[ 301.566618] ? __warn+0x81/0x130
[ 301.566876] ? untrack_pfn+0xf4/0x100
[ 301.567163] ? report_bug+0x171/0x1a0
[ 301.567466] ? handle_bug+0x3c/0x80
[ 301.567743] ? exc_invalid_op+0x17/0x70
[ 301.568038] ? asm_exc_invalid_op+0x1a/0x20
[ 301.568363] ? untrack_pfn+0xf4/0x100
[ 301.568660] ? untrack_pfn+0x65/0x100
[ 301.568947] unmap_single_vma+0xa6/0xe0
[ 301.569247] unmap_vmas+0xb5/0x190
[ 301.569532] exit_mmap+0xec/0x340
[ 301.569801] __mmput+0x3e/0x130
[ 301.570051] do_exit+0x305/0xaf0
...
Link: https://lkml.kernel.org/r/20240403212131.929421-3-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Reported-by: Wupeng Ma <mawupeng1@huawei.com>
Closes: https://lkml.kernel.org/r/20240227122814.3781907-1-mawupeng1@huawei.com
Fixes: b1a86e15dc ("x86, pat: remove the dependency on 'vm_pgoff' in track/untrack pfn vma routines")
Fixes: 5899329b19 ("x86: PAT: implement track/untrack of pfnmap regions for x86 - v3")
Acked-by: Ingo Molnar <mingo@kernel.org>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8917e73853 upstream.
In the following sequence:
1) of_platform_depopulate()
2) of_overlay_remove()
During the step 1, devices are destroyed and devlinks are removed.
During the step 2, OF nodes are destroyed but
__of_changeset_entry_destroy() can raise warnings related to missing
of_node_put():
ERROR: memory leak, expected refcount 1 instead of 2 ...
Indeed, during the devlink removals performed at step 1, the removal
itself releasing the device (and the attached of_node) is done by a job
queued in a workqueue and so, it is done asynchronously with respect to
function calls.
When the warning is present, of_node_put() will be called but wrongly
too late from the workqueue job.
In order to be sure that any ongoing devlink removals are done before
the of_node destruction, synchronize the of_changeset_destroy() with the
devlink removals.
Fixes: 80dd33cf72 ("drivers: base: Fix device link removal")
Cc: stable@vger.kernel.org
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Saravana Kannan <saravanak@google.com>
Tested-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240325152140.198219-3-herve.codina@bootlin.com
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0462c56c29 upstream.
The commit 80dd33cf72 ("drivers: base: Fix device link removal")
introduces a workqueue to release the consumer and supplier devices used
in the devlink.
In the job queued, devices are release and in turn, when all the
references to these devices are dropped, the release function of the
device itself is called.
Nothing is present to provide some synchronisation with this workqueue
in order to ensure that all ongoing releasing operations are done and
so, some other operations can be started safely.
For instance, in the following sequence:
1) of_platform_depopulate()
2) of_overlay_remove()
During the step 1, devices are released and related devlinks are removed
(jobs pushed in the workqueue).
During the step 2, OF nodes are destroyed but, without any
synchronisation with devlink removal jobs, of_overlay_remove() can raise
warnings related to missing of_node_put():
ERROR: memory leak, expected refcount 1 instead of 2
Indeed, the missing of_node_put() call is going to be done, too late,
from the workqueue job execution.
Introduce device_link_wait_removal() to offer a way to synchronize
operations waiting for the end of devlink removals (i.e. end of
workqueue jobs).
Also, as a flushing operation is done on the workqueue, the workqueue
used is moved from a system-wide workqueue to a local one.
Cc: stable@vger.kernel.org
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Tested-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Reviewed-by: Saravana Kannan <saravanak@google.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240325152140.198219-2-herve.codina@bootlin.com
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 561e4f9451 upstream.
If we look up the kbuf, ensure that it doesn't get unregistered until
after we're done with it. Since we're inside mmap, we cannot safely use
the io_uring lock. Rely on the fact that we can lookup the buffer list
under RCU now and grab a reference to it, preventing it from being
unregistered until we're done with it. The lookup returns the
io_buffer_list directly with it referenced.
Cc: stable@vger.kernel.org # v6.4+
Fixes: 5cf4f52e6d ("io_uring: free io_buffer_list entries via RCU")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b69c4ab4f upstream.
No functional changes in this patch, just in preparation for being able
to keep the buffer list alive outside of the ctx->uring_lock.
Cc: stable@vger.kernel.org # v6.4+
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3b80cff5a4 upstream.
Now that xarray is being exclusively used for the buffer_list lookup,
this check is no longer needed. Get rid of it and the is_ready member.
Cc: stable@vger.kernel.org # v6.4+
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1576f263ee upstream.
This patch addresses an issue with the Panasonic CF-SZ6's existing quirk,
specifically its headset microphone functionality. Previously, the quirk
used ALC269_FIXUP_HEADSET_MODE, which does not support the CF-SZ6's design
of a single 3.5mm jack for both mic and audio output effectively. The
device uses pin 0x19 for the headset mic without jack detection.
Following verification on the CF-SZ6 and discussions with the original
patch author, i determined that the update to
ALC269_FIXUP_ASPIRE_HEADSET_MIC is the appropriate solution. This change
is custom-designed for the CF-SZ6's unique hardware setup, which includes
a single 3.5mm jack for both mic and audio output, connecting the headset
microphone to pin 0x19 without the use of jack detection.
Fixes: 0fca97a29b ("ALSA: hda/realtek - Add Panasonic CF-SZ6 headset jack quirk")
Signed-off-by: I Gede Agastya Darma Laksana <gedeagas22@gmail.com>
Cc: <stable@vger.kernel.org>
Message-ID: <20240401174602.14133-1-gedeagas22@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a677ebd8ca upstream.
If installing malicious ksmbd-tools, ksmbd.mountd can return invalid ipc
response to ksmbd kernel server. ksmbd should validate payload size of
ipc response from ksmbd.mountd to avoid memory overrun or
slab-out-of-bounds. This patch validate 3 ipc response that has payload.
Cc: stable@vger.kernel.org
Reported-by: Chao Ma <machao2019@gmail.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 83092341e1 upstream.
When adding sanitization of the label, the path through
edge_detector_setup() that leads to debounce_setup() was overlooked.
A request taking this path does not allocate a new label and the
request label is freed twice when the request is released, resulting
in memory corruption.
Add label sanitization to debounce_setup().
Cc: stable@vger.kernel.org
Fixes: b34490879b ("gpio: cdev: sanitize the label before requesting the interrupt")
Signed-off-by: Kent Gibson <warthog618@gmail.com>
[Bartosz: rebased on top of the fix for empty GPIO labels]
Co-developed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b377c66ae3 upstream.
srso_alias_untrain_ret() is special code, even if it is a dummy
which is called in the !SRSO case, so annotate it like its real
counterpart, to address the following objtool splat:
vmlinux.o: warning: objtool: .export_symbol+0x2b290: data relocation to !ENDBR: srso_alias_untrain_ret+0x0
Fixes: 4535e1a417 ("x86/bugs: Fix the SRSO mitigation on Zen3/4")
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lore.kernel.org/r/20240405144637.17908-1-bp@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 10396f4df8 ]
Currently the CB_RECALL_ANY job takes a cl_rpc_users reference to the
client. While a callback job is technically an RPC that counter is
really more for client-driven RPCs, and this has the effect of
preventing the client from being unhashed until the callback completes.
If nfsd decides to send a CB_RECALL_ANY just as the client reboots, we
can end up in a situation where the callback can't complete on the (now
dead) callback channel, but the new client can't connect because the old
client can't be unhashed. This usually manifests as a NFS4ERR_DELAY
return on the CREATE_SESSION operation.
The job is only holding a reference to the client so it can clear a flag
after the RPC completes. Fix this by having CB_RECALL_ANY instead hold a
reference to the cl_nfsdfs.cl_ref. Typically we only take that sort of
reference when dealing with the nfsdfs info files, but it should work
appropriately here to ensure that the nfs4_client doesn't disappear.
Fixes: 44df6f439a ("NFSD: add delegation reaper to react to low memory condition")
Reported-by: Vladimir Benes <vbenes@redhat.com>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05258a0a69 ]
Jan Schunk reports that his small NFS servers suffer from memory
exhaustion after just a few days. A bisect shows that commit
e18e157bb5 ("SUNRPC: Send RPC message on TCP with a single
sock_sendmsg() call") is the first bad commit.
That commit assumed that sock_sendmsg() releases all the pages in
the underlying bio_vec array, but the reality is that it doesn't.
svc_xprt_release() releases the rqst's response pages, but the
record marker page fragment isn't one of those, so it is never
released.
This is a narrow fix that can be applied to stable kernels. A
more extensive fix is in the works.
Reported-by: Jan Schunk <scpcom@gmx.de>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218671
Fixes: e18e157bb5 ("SUNRPC: Send RPC message on TCP with a single sock_sendmsg() call")
Cc: Alexander Duyck <alexander.duyck@gmail.com>
Cc: Jakub Kacinski <kuba@kernel.org>
Cc: David Howells <dhowells@redhat.com>
Reviewed-by: David Howells <dhowells@redhat.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b9846a3867 ]
Before ACP firmware loading, DSP interrupts are not expected.
Sometimes after reboot, it's observed that before ACP firmware is loaded
false DSP interrupt is reported.
Registering the interrupt handler before acp initialization causing false
interrupts sometimes on reboot as ACP reset is not applied.
Correct the sequence by invoking acp initialization sequence prior to
registering interrupt handler.
Fixes: 738a2b5e2c ("ASoC: SOF: amd: Add IPC support for ACP IP block")
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://msgid.link/r/20240404041717.430545-1-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3137b83a90 ]
Building with W=1 shows a warning for an unused variable when CONFIG_PCI
is diabled:
drivers/ata/sata_mv.c:790:35: error: unused variable 'mv_pci_tbl' [-Werror,-Wunused-const-variable]
static const struct pci_device_id mv_pci_tbl[] = {
Move the table into the same block that containsn the pci_driver
definition.
Fixes: 7bb3c5290c ("sata_mv: Remove PCI dependency")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1f886a7bfb ]
In function pci1xxxx_spi_probe, there is a potential null pointer that
may be caused by a failed memory allocation by the function devm_kzalloc.
Hence, a null pointer check needs to be added to prevent null pointer
dereferencing later in the code.
To fix this issue, spi_bus->spi_int[iter] should be checked. The memory
allocated by devm_kzalloc will be automatically released, so just directly
return -ENOMEM without worrying about memory leaks.
Fixes: 1cc0cbea71 ("spi: microchip: pci1xxxx: Add driver for SPI controller of PCI1XXXX PCIe switch")
Signed-off-by: Huai-Yuan Liu <qq810974084@gmail.com>
Link: https://msgid.link/r/20240403014221.969801-1-qq810974084@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e9e62243a3 ]
When we're engaged in local caching of a cifs filesystem, we cannot perform
caching of a partially written cache granule unless we can read the rest of
the granule. This can result in unexpected access errors being reported to
the user.
Fix this by the following: if a file is opened O_WRONLY locally, but the
mount was given the "-o fsc" flag, try first opening the remote file with
GENERIC_READ|GENERIC_WRITE and if that returns -EACCES, try dropping the
GENERIC_READ and doing the open again. If that last succeeds, invalidate
the cache for that file as for O_DIRECT.
Fixes: 70431bfd82 ("cifs: Support fscache indexing rewrite")
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Steve French <sfrench@samba.org>
cc: Shyam Prasad N <nspmangalore@gmail.com>
cc: Rohith Surabattula <rohiths.msft@gmail.com>
cc: Jeff Layton <jlayton@kernel.org>
cc: linux-cifs@vger.kernel.org
cc: netfs@lists.linux.dev
cc: linux-fsdevel@vger.kernel.org
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03f56ed4ea ]
As already anticipated in the original commit, playback was broken for
very short samples. I just didn't expect it to be an actual problem,
because we're talking about less than 1.5 milliseconds here. But clearly
such wavetable samples do actually exist.
The problem was that for such short samples we'd set the current
position beyond the end of the loop, so we'd run off the end of the
sample and play garbage.
This is a bigger (more audible) problem than the original one, which was
that we'd start playback with garbage (whatever was still in the cache),
which would be mostly masked by the note's attack phase.
So revert to the old behavior for now. We'll subsequently fix it
properly with a bigger patch series.
Note that this isn't a full revert - the dead code is not re-introduced,
because that would be silly.
Fixes: df335e9a8b ("ALSA: emu10k1: fix synthesizer sample playback position and caching")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218625
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Message-ID: <20240401145805.528794-1-oswald.buddenhagen@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1197c5b209 ]
The myrb and myrs drivers use an odd way of implementing their sysfs files,
calling snprintf() with a fixed length of 32 bytes to print into a page
sized buffer. One of the strings is actually longer than 32 bytes, which
clang can warn about:
drivers/scsi/myrb.c:1906:10: error: 'snprintf' will always be truncated; specified size is 32, but format string expands to at least 34 [-Werror,-Wformat-truncation]
drivers/scsi/myrs.c:1089:10: error: 'snprintf' will always be truncated; specified size is 32, but format string expands to at least 34 [-Werror,-Wformat-truncation]
These could all be plain sprintf() without a length as the buffer is always
long enough. On the other hand, sysfs files should not be overly long
either, so just double the length to make sure the longest strings don't
get truncated here.
Fixes: 7726618639 ("scsi: myrs: Add Mylex RAID controller (SCSI interface)")
Fixes: 081ff398c5 ("scsi: myrb: Add Mylex RAID controller (block interface)")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240326223825.4084412-8-arnd@kernel.org
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 52f80bb181 ]
gcc warns about a memcpy() with overlapping pointers because of an
incorrect size calculation:
In file included from include/linux/string.h:369,
from drivers/ata/sata_sx4.c:66:
In function 'memcpy_fromio',
inlined from 'pdc20621_get_from_dimm.constprop' at drivers/ata/sata_sx4.c:962:2:
include/linux/fortify-string.h:97:33: error: '__builtin_memcpy' accessing 4294934464 bytes at offsets 0 and [16, 16400] overlaps 6442385281 bytes at offset -2147450817 [-Werror=restrict]
97 | #define __underlying_memcpy __builtin_memcpy
| ^
include/linux/fortify-string.h:620:9: note: in expansion of macro '__underlying_memcpy'
620 | __underlying_##op(p, q, __fortify_size); \
| ^~~~~~~~~~~~~
include/linux/fortify-string.h:665:26: note: in expansion of macro '__fortify_memcpy_chk'
665 | #define memcpy(p, q, s) __fortify_memcpy_chk(p, q, s, \
| ^~~~~~~~~~~~~~~~~~~~
include/asm-generic/io.h:1184:9: note: in expansion of macro 'memcpy'
1184 | memcpy(buffer, __io_virt(addr), size);
| ^~~~~~
The problem here is the overflow of an unsigned 32-bit number to a
negative that gets converted into a signed 'long', keeping a large
positive number.
Replace the complex calculation with a more readable min() variant
that avoids the warning.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a3d3eab627 ]
If the SPI data size is smaller than FIFO, it operates in PIO mode,
and if it is larger than FIFO size, it oerates in DMA mode.
If the SPI data size is equal to fifo, it operates in PIO mode and it is
separated to 2 transfers. To prevent it, it must operate in DMA mode
from the case where the data size and the fifo size are the same.
Fixes: 1ee806718d ("spi: s3c64xx: support interrupt based pio mode")
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20240329085840.65856-1-jaewon02.kim@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d6911cf27e ]
The driver is wrong because is using partial register field masks for the
SPI_STATUS.{RX, TX}_FIFO_LVL register fields.
We see s3c64xx_spi_port_config.fifo_lvl_mask with different values for
different instances of the same IP. Take s5pv210_spi_port_config for
example, it defines:
.fifo_lvl_mask = { 0x1ff, 0x7F },
fifo_lvl_mask is used to determine the FIFO depth of the instance of the
IP. In this case, the integrator uses a 256 bytes FIFO for the first SPI
instance of the IP, and a 64 bytes FIFO for the second instance. While
the first mask reflects the SPI_STATUS.{RX, TX}_FIFO_LVL register
fields, the second one is two bits short. Using partial field masks is
misleading and can hide problems of the driver's logic.
Allow platforms to specify the full FIFO mask, regardless of the FIFO
depth.
Introduce {rx, tx}_fifomask to represent the SPI_STATUS.{RX, TX}_FIFO_LVL
register fields. It's a shifted mask defining the field's length and
position. We'll be able to deprecate the use of @rx_lvl_offset, as the
shift value can be determined from the mask. The existing compatibles
shall start using {rx, tx}_fifomask so that they use the full field mask
and to avoid shifting the mask to position, and then shifting it back to
zero in the {TX, RX}_FIFO_LVL macros.
@rx_lvl_offset will be deprecated in a further patch, after we have the
infrastructure to deprecate @fifo_lvl_mask as well.
No functional change intended.
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://msgid.link/r/20240216070555.2483977-4-tudor.ambarus@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: a3d3eab627 ("spi: s3c64xx: Use DMA mode from fifo size")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc563aa900 ]
In snd_soc_info_volsw(), mask is generated by figuring out the index of
the most significant bit set in max and converting the index to a
bitmask through bit shift 1. Unintended wraparound occurs when max is an
integer value with msb bit set. Since the bit shift value 1 is treated
as an integer type, the left shift operation will wraparound and set
mask to 0 instead of all 1's. In order to fix this, we type cast 1 as
`1ULL` to prevent the wraparound.
Fixes: 7077148fb5 ("ASoC: core: Split ops out of soc-core.c")
Signed-off-by: Stephen Lee <slee08177@gmail.com>
Link: https://msgid.link/r/20240326010131.6211-1-slee08177@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be141849ec ]
dEQP-VK.sparse_resources.image_rebind.2d_array.r64i.128_128_8
was causing a remap operation like the below.
op_remap: prev: 0000003fffed0000 00000000000f0000 00000000a5abd18a 0000000000000000
op_remap: next:
op_remap: unmap: 0000003fffed0000 0000000000100000 0
op_map: map: 0000003ffffc0000 0000000000010000 000000005b1ba33c 00000000000e0000
This was resulting in an unmap operation from 0x3fffed0000+0xf0000, 0x100000
which was corrupting the pagetables and oopsing the kernel.
Fixes the prev + unmap range calcs to use start/end and map back to addr/range.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fixes: b88baab828 ("drm/nouveau: implement new VM_BIND uAPI")
Cc: Danilo Krummrich <dakr@redhat.com>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240328024317.2041851-1-airlied@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2bd02f5a0b ]
Increase the timeout value to prevent system logs on Amlogic boards flooding
with power transition warnings:
[ 13.047638] panfrost ffe40000.gpu: shader power transition timeout
[ 13.048674] panfrost ffe40000.gpu: l2 power transition timeout
[ 13.937324] panfrost ffe40000.gpu: shader power transition timeout
[ 13.938351] panfrost ffe40000.gpu: l2 power transition timeout
...
[39829.506904] panfrost ffe40000.gpu: shader power transition timeout
[39829.507938] panfrost ffe40000.gpu: l2 power transition timeout
[39949.508369] panfrost ffe40000.gpu: shader power transition timeout
[39949.509405] panfrost ffe40000.gpu: l2 power transition timeout
The 2000 value has been found through trial and error testing with devices
using G52 and G31 GPUs.
Fixes: 22aa1a2090 ("drm/panfrost: Really power off GPU cores in panfrost_gpu_power_off()")
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240322164525.2617508-1-christianshewitt@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d0401ee38 ]
Adding the ACPI HIDs to the match table triggers the cs35l56-hda modules
to be loaded on boot so that Serial Multi Instantiate can add the
devices to the bus and begin the driver init sequence.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Fixes: 73cfbfa9ca ("ALSA: hda/cs35l56: Add driver for Cirrus Logic CS35L56 amplifier")
Message-ID: <20240328121355.18972-1-simont@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 00bb549d7d ]
When keeping the upper end of a cache block entry, the entry[] array
must be indexed by the offset from the base register of the block,
i.e. max - mas.index.
The code was indexing entry[] by only the register address, leading
to an out-of-bounds access that copied some part of the kernel
memory over the cache contents.
This bug was not detected by the regmap KUnit test because it only
tests with a block of registers starting at 0, so mas.index == 0.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: f033c26de5 ("regmap: Add maple tree based register cache")
Link: https://msgid.link/r/20240327114406.976986-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f193957b0f ]
wm_adsp_write_ctl() must hold the pwr_lock mutex when calling
cs_dsp_get_ctl().
This was previously partially fixed by commit 781118bc2f
("ASoC: wm_adsp: Fix missing locking in wm_adsp_[read|write]_ctl()")
but this only put locking around the call to cs_dsp_coeff_write_ctrl(),
missing the call to cs_dsp_get_ctl().
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 781118bc2f ("ASoC: wm_adsp: Fix missing locking in wm_adsp_[read|write]_ctl()")
Link: https://msgid.link/r/20240307110227.41421-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be3193e58e ]
Previous conversion to iov missed these debug statements which would now
always print the requested size instead of the actual server reply.
Write also added a loop in a much older commit but we didn't report
these, while reads do report each iteration -- it's more coherent to
keep reporting all requests to server so move that at the same time.
Fixes: 7f02464739 ("9p: convert to advancing variant of iov_iter_get_pages_alloc()")
Signed-off-by: Dominique Martinet <asmadeus@codewreck.org>
Message-ID: <20240109-9p-rw-trace-v1-1-327178114257@codewreck.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 055ca83559 ]
When you try to splice between a normal pipe and a notification pipe,
get_pipe_info(..., true) fails, so splice() falls back to treating the
notification pipe like a normal pipe - so we end up in
iter_file_splice_write(), which first locks the input pipe, then calls
vfs_iter_write(), which locks the output pipe.
Lockdep complains about that, because we're taking a pipe lock while
already holding another pipe lock.
I think this probably (?) can't actually lead to deadlocks, since you'd
need another way to nest locking a normal pipe into locking a
watch_queue pipe, but the lockdep annotations don't make that clear.
Bail out earlier in pipe_write() for notification pipes, before taking
the pipe lock.
Reported-and-tested-by: <syzbot+011e4ea1da6692cf881c@syzkaller.appspotmail.com>
Closes: https://syzkaller.appspot.com/bug?extid=011e4ea1da6692cf881c
Fixes: c73be61ced ("pipe: Add general notification queue support")
Signed-off-by: Jann Horn <jannh@google.com>
Link: https://lore.kernel.org/r/20231124150822.2121798-1-jannh@google.com
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 466eec4a22 ]
Convert all local ASID variables and parameters throughout the SEV code
from signed integers to unsigned integers. As ASIDs are fundamentally
unsigned values, and the global min/max variables are appropriately
unsigned integers, too.
Functionally, this is a glorified nop as KVM guarantees min_sev_asid is
non-zero, and no CPU supports -1u as the _only_ asid, i.e. the signed vs.
unsigned goof won't cause problems in practice.
Opportunistically use sev_get_asid() in sev_flush_encrypted_page() instead
of open coding an equivalent.
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lore.kernel.org/r/20240131235609.4161407-3-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Stable-dep-of: 0aa6b90ef9 ("KVM: SVM: Add support for allowing zero SEV ASIDs")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 101b76418d ]
The error statistics should be updated each time the poll function is
called, even if the full RX work budget has been consumed. This prevents
the counts from becoming stuck when RX bandwidth usage is high.
This also ensures that error counters are not updated after we've
re-enabled interrupts as that could result in a race condition.
Also drop an unnecessary space.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20240402145305.82148-2-paul.barker.ct@bp.renesas.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2b993bfdb4 ]
ravb_poll() initial code used to interrogate the first descriptor of the
RX queue in case gPTP is false to determine if ravb_rx() should be called.
This is done for non-gPTP IPs. For gPTP IPs the driver PTP-specific
information was used to determine if receive function should be called. As
every IP has its own receive function that interrogates the RX descriptors
list in the same way the ravb_poll() was doing there is no need to double
check this in ravb_poll(). Removing the code from ravb_poll() leads to a
cleaner code.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Stable-dep-of: 596a425491 ("net: ravb: Always process TX descriptor ring")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 861e808602 ]
Forcing SMBUS inside the ULP enabling flow leads to sporadic PHY loss on
some systems. It is suspected to be caused by initiating PHY transactions
before the interface settles.
Separating this configuration from the ULP enabling flow and moving it to
the shutdown function allows enough time for the interface to settle and
avoids adding a delay.
Fixes: 6607c99e70 ("e1000e: i219 - fix to enable both ULP and EEE in Sx state")
Co-developed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6dbdd4de03 ]
On some Meteor Lake systems accessing the PHY via the MDIO interface may
result in an MDI error. This issue happens sporadically and in most cases
a second access to the PHY via the MDIO interface results in success.
As a workaround, introduce a retry counter which is set to 3 on Meteor
Lake systems. The driver will only return an error if 3 consecutive PHY
access attempts fail. The retry mechanism is disabled in specific flows,
where MDI errors are expected.
Fixes: cc23f4f0b6 ("e1000e: Add support for Meteor Lake")
Suggested-by: Nikolay Mushayev <nikolay.mushayev@intel.com>
Co-developed-by: Nir Efrati <nir.efrati@intel.com>
Signed-off-by: Nir Efrati <nir.efrati@intel.com>
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b9a4525450 ]
Refactor several older Intel drivers to use FIELD_GET(), which reduces
lines of code and adds clarity of intent.
This code was generated by the following coccinelle/spatch script and
then manually repaired.
@get@
constant shift,mask;
type T;
expression a;
@@
(
-((T)((a) & mask) >> shift)
+FIELD_GET(mask, a)
and applied via:
spatch --sp-file field_prep.cocci --in-place --dir \
drivers/net/ethernet/intel/
Cc: Julia Lawall <Julia.Lawall@inria.fr>
CC: Alexander Lobakin <aleksander.lobakin@intel.com>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Stable-dep-of: 6dbdd4de03 ("e1000e: Workaround for sporadic MDI error on Meteor Lake systems")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3314f2097d ]
This series is introducing the use of FIELD_GET and FIELD_PREP which
requires bitfield.h to be included. Fix all the includes in this one
change, and rearrange includes into alphabetical order to ease
readability and future maintenance.
virtchnl.h and it's usage was modified to have it's own includes as it
should. This required including bits.h for virtchnl.h.
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Stable-dep-of: 6dbdd4de03 ("e1000e: Workaround for sporadic MDI error on Meteor Lake systems")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 56df345917 ]
Similarly as for ice driver [1] there are also circular header
dependencies in i40e driver:
i40e.h -> i40e_virtchnl_pf.h -> i40e.h
Another issue is that i40e header files does not contain their own
dependencies on other header files (both private and standard) so their
inclusion in .c file require to add these deps in certain order to
that .c file to make it compilable.
Fix both issues by removal the mentioned circular dependency, by filling
i40e headers with their dependencies so they can be placed anywhere in
a source code. Additionally remove bunch of includes from i40e.h super
header file that are not necessary and include i40e.h only in .c files
that really require it.
[1] 649c87c6ff ("ice: remove circular header dependencies on ice.h")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Stable-dep-of: 6dbdd4de03 ("e1000e: Workaround for sporadic MDI error on Meteor Lake systems")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7151d87a17 ]
The <linux/avf/virtchnl.h> uses BIT, struct_size and ETH_ALEN macros
but does not include appropriate header files that defines them.
Add these dependencies so this header file can be included anywhere.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Stable-dep-of: 6dbdd4de03 ("e1000e: Workaround for sporadic MDI error on Meteor Lake systems")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8196b5fd6c ]
The macros I40E_MDIO_CLAUSE22* and I40E_MDIO_CLAUSE45* are using I40E_MASK
together with the same values I40E_GLGEN_MSCA_STCODE_SHIFT and
I40E_GLGEN_MSCA_OPCODE_SHIFT to define masks.
Introduce I40E_GLGEN_MSCA_OPCODE_MASK and I40E_GLGEN_MSCA_STCODE_MASK
for both shifts in i40e_register.h and use them to refactor the macros
mentioned above.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Stable-dep-of: 6dbdd4de03 ("e1000e: Workaround for sporadic MDI error on Meteor Lake systems")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39ec612acf ]
The .back field placed in i40e_hw is used to get pointer to i40e_pf
instance but it is not necessary as the i40e_hw is a part of i40e_pf
and containerof macro can be used to obtain the pointer to i40e_pf.
Remove .back field from i40e_hw structure, introduce i40e_hw_to_pf()
and i40e_hw_to_dev() helpers and use them.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Stable-dep-of: 6dbdd4de03 ("e1000e: Workaround for sporadic MDI error on Meteor Lake systems")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea558de723 ]
As for ice bug fixed by commit b7306b42be ("ice: manage interrupts
during poll exit") followed by commit 23be7075b3 ("ice: fix software
generating extra interrupts") I'm seeing the similar issue also with
i40e driver.
In certain situation when busy-loop is enabled together with adaptive
coalescing, the driver occasionally misses that there are outstanding
descriptors to clean when exiting busy poll.
Try to catch the remaining work by triggering a software interrupt
when exiting busy poll. No extra interrupts will be generated when
busy polling is not used.
The issue was found when running sockperf ping-pong tcp test with
adaptive coalescing and busy poll enabled (50 as value busy_pool
and busy_read sysctl knobs) and results in huge latency spikes
with more than 100000us.
The fix is inspired from the ice driver and do the following:
1) During napi poll exit in case of busy-poll (napo_complete_done()
returns false) this is recorded to q_vector that we were in busy
loop.
2) Extends i40e_buildreg_itr() to be able to add an enforced software
interrupt into built value
2) In i40e_update_enable_itr() enforces a software interrupt trigger
if we are exiting busy poll to catch any pending clean-ups
3) Reuses unused 3rd ITR (interrupt throttle) index and set it to
20K interrupts per second to limit the number of these sw interrupts.
Test results
============
Prior:
[root@dell-per640-07 net]# sockperf ping-pong -i 10.9.9.1 --tcp -m 1000 --mps=max -t 120
sockperf: == version #3.10-no.git ==
sockperf[CLIENT] send on:sockperf: using recvfrom() to block on socket(s)
[ 0] IP = 10.9.9.1 PORT = 11111 # TCP
sockperf: Warmup stage (sending a few dummy messages)...
sockperf: Starting test...
sockperf: Test end (interrupted by timer)
sockperf: Test ended
sockperf: [Total Run] RunTime=119.999 sec; Warm up time=400 msec; SentMessages=2438563; ReceivedMessages=2438562
sockperf: ========= Printing statistics for Server No: 0
sockperf: [Valid Duration] RunTime=119.549 sec; SentMessages=2429473; ReceivedMessages=2429473
sockperf: ====> avg-latency=24.571 (std-dev=93.297, mean-ad=4.904, median-ad=1.510, siqr=1.063, cv=3.797, std-error=0.060, 99.0% ci=[24.417, 24.725])
sockperf: # dropped messages = 0; # duplicated messages = 0; # out-of-order messages = 0
sockperf: Summary: Latency is 24.571 usec
sockperf: Total 2429473 observations; each percentile contains 24294.73 observations
sockperf: ---> <MAX> observation = 103294.331
sockperf: ---> percentile 99.999 = 45.633
sockperf: ---> percentile 99.990 = 37.013
sockperf: ---> percentile 99.900 = 35.910
sockperf: ---> percentile 99.000 = 33.390
sockperf: ---> percentile 90.000 = 28.626
sockperf: ---> percentile 75.000 = 27.741
sockperf: ---> percentile 50.000 = 26.743
sockperf: ---> percentile 25.000 = 25.614
sockperf: ---> <MIN> observation = 12.220
After:
[root@dell-per640-07 net]# sockperf ping-pong -i 10.9.9.1 --tcp -m 1000 --mps=max -t 120
sockperf: == version #3.10-no.git ==
sockperf[CLIENT] send on:sockperf: using recvfrom() to block on socket(s)
[ 0] IP = 10.9.9.1 PORT = 11111 # TCP
sockperf: Warmup stage (sending a few dummy messages)...
sockperf: Starting test...
sockperf: Test end (interrupted by timer)
sockperf: Test ended
sockperf: [Total Run] RunTime=119.999 sec; Warm up time=400 msec; SentMessages=2400055; ReceivedMessages=2400054
sockperf: ========= Printing statistics for Server No: 0
sockperf: [Valid Duration] RunTime=119.549 sec; SentMessages=2391186; ReceivedMessages=2391186
sockperf: ====> avg-latency=24.965 (std-dev=5.934, mean-ad=4.642, median-ad=1.485, siqr=1.067, cv=0.238, std-error=0.004, 99.0% ci=[24.955, 24.975])
sockperf: # dropped messages = 0; # duplicated messages = 0; # out-of-order messages = 0
sockperf: Summary: Latency is 24.965 usec
sockperf: Total 2391186 observations; each percentile contains 23911.86 observations
sockperf: ---> <MAX> observation = 195.841
sockperf: ---> percentile 99.999 = 45.026
sockperf: ---> percentile 99.990 = 39.009
sockperf: ---> percentile 99.900 = 35.922
sockperf: ---> percentile 99.000 = 33.482
sockperf: ---> percentile 90.000 = 28.902
sockperf: ---> percentile 75.000 = 27.821
sockperf: ---> percentile 50.000 = 26.860
sockperf: ---> percentile 25.000 = 25.685
sockperf: ---> <MIN> observation = 12.277
Fixes: 0bcd952fee ("ethernet/intel: consolidate NAPI and NAPI exit")
Reported-by: Hugo Ferreira <hferreir@redhat.com>
Reviewed-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb11ca3233 ]
If any IP blocks allocate memory during their hw_fini() sequence
this can cause the suspend to fail under memory pressure. Introduce
a new phase that IP blocks can use to allocate memory before suspend
starts so that it can potentially be evicted into swap instead.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stable-dep-of: ca299b4512 ("drm/amd: Flush GFXOFF requests in prepare stage")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5095d54181 ]
Linux PM core has a prepare() callback run before suspend.
If the system is under high memory pressure, the resources may need
to be evicted into swap instead. If the storage backing for swap
is offlined during the suspend() step then such a call may fail.
So move this step into prepare() to move evict majority of
resources and update all non-pmops callers to call the same callback.
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2362
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stable-dep-of: ca299b4512 ("drm/amd: Flush GFXOFF requests in prepare stage")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f5e9bda03a ]
When orientation switch is enabled in ucsi glink, there is a xhci
probe failure seen when booting up in host mode in reverse
orientation.
During bootup the following things happen in multiple drivers:
a) DWC3 controller driver initializes the core in device mode when the
dr_mode is set to DRD. It relies on role_switch call to change role to
host.
b) QMP driver initializes the lanes to TYPEC_ORIENTATION_NORMAL as a
normal routine. It relies on the typec_switch_set call to get notified
of orientation changes.
c) UCSI core reads the UCSI_GET_CONNECTOR_STATUS via the glink and
provides initial role switch to dwc3 controller.
When booting up in host mode with orientation TYPEC_ORIENTATION_REVERSE,
then we see the following things happening in order:
a) UCSI gives initial role as host to dwc3 controller ucsi_register_port.
Upon receiving this notification, the dwc3 core needs to program GCTL from
PRTCAP_DEVICE to PRTCAP_HOST and as part of this change, it asserts GCTL
Core soft reset and waits for it to be completed before shifting it to
host. Only after the reset is done will the dwc3_host_init be invoked and
xhci is probed. DWC3 controller expects that the usb phy's are stable
during this process i.e., the phy init is already done.
b) During the 100ms wait for GCTL core soft reset, the actual notification
from PPM is received by ucsi_glink via pmic glink for changing role to
host. The pmic_glink_ucsi_notify routine first sends the orientation
change to QMP and then sends role to dwc3 via ucsi framework. This is
happening exactly at the time GCTL core soft reset is being processed.
c) When QMP driver receives typec switch to TYPEC_ORIENTATION_REVERSE, it
then re-programs the phy at the instant GCTL core soft reset has been
asserted by dwc3 controller due to which the QMP PLL lock fails in
qmp_combo_usb_power_on.
d) After the 100ms of GCTL core soft reset is completed, the dwc3 core
goes for initializing the host mode and invokes xhci probe. But at this
point the QMP is non-responsive and as a result, the xhci plat probe fails
during xhci_reset.
Fix this by passing orientation switch to available ucsi instances if
their gpio configuration is available before ucsi_register is invoked so
that by the time, the pmic_glink_ucsi_notify provides typec_switch to QMP,
the lane is already configured and the call would be a NOP thus not racing
with role switch.
Cc: stable@vger.kernel.org
Fixes: c6165ed2f4 ("usb: ucsi: glink: use the connector orientation GPIO to provide switch events")
Suggested-by: Wesley Cheng <quic_wcheng@quicinc.com>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240301040914.458492-1-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f37c4eac99 upstream.
To fix the regression introduced by commit 52424f974b, which causes
servers hang in very hard to reproduce conditions with resets races.
Using two sources for the information is the root cause.
In this function before the fix bumping v didn't mean bumping vf
pointer. But the code used this variables interchangeably, so stale vf
could point to different/not intended vf.
Remove redundant "v" variable and iterate via single VF pointer across
whole function instead to guarantee VF pointer validity.
Fixes: 52424f974b ("i40e: Fix VF hang when reset is triggered on another VF")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eb58c598ce upstream.
The bug usually affects untrusted VFs, because they are limited to 18 MACs,
it affects them badly, not letting to create MAC all filters.
Not stable to reproduce, it happens when VF user creates MAC filters
when other MACVLAN operations are happened in parallel.
But consequence is that VF can't receive desired traffic.
Fix counter to be bumped only for new or active filters.
Fixes: 621650cabe ("i40e: Refactoring VF MAC filters counting to make more reliable")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef15ddeeb6 upstream.
In rvu_map_cgx_lmac_pf() the 'iter', which is used as an array index, can reach
value (up to 14) that exceed the size (MAX_LMAC_COUNT = 8) of the array.
Fix this bug by adding 'iter' value check.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 91c6945ea1 ("octeontx2-af: cn10k: Add RPM MAC support")
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0ba80d9658 upstream.
The current implementation for loading coalesced KPU profiles has
a limitation. The "offset" field, which is used to locate profiles
within the profile is restricted to a u16.
This restricts the number of profiles that can be loaded. This patch
addresses this limitation by increasing the size of the "offset" field.
Fixes: 11c730bfbf ("octeontx2-af: support for coalescing KPU profiles")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 64235eabc4 upstream.
GRO has a fundamental issue with UDP tunnel packets as it can't detect
those in a foolproof way and GRO could happen before they reach the
tunnel endpoint. Previous commits have fixed issues when UDP tunnel
packets come from a remote host, but if those packets are issued locally
they could run into checksum issues.
If the inner packet has a partial checksum the information will be lost
in the GRO logic, either in udp4/6_gro_complete or in
udp_gro_complete_segment and packets will have an invalid checksum when
leaving the host.
Prevent local UDP tunnel packets from ever being GROed at the outer UDP
level.
Due to skb->encapsulation being wrongly used in some drivers this is
actually only preventing UDP tunnel packets with a partial checksum to
be GROed (see iptunnel_handle_offloads) but those were also the packets
triggering issues so in practice this should be sufficient.
Fixes: 9fd1ff5d2a ("udp: Support UDP fraglist GRO/GSO.")
Fixes: 36707061d6 ("udp: allow forwarding of plain (non-fraglisted) UDP GRO packets")
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f0b8c30345 upstream.
UDP GRO validates checksums and in udp4/6_gro_complete fraglist packets
are converted to CHECKSUM_UNNECESSARY to avoid later checks. However
this is an issue for CHECKSUM_PARTIAL packets as they can be looped in
an egress path and then their partial checksums are not fixed.
Different issues can be observed, from invalid checksum on packets to
traces like:
gen01: hw csum failure
skb len=3008 headroom=160 headlen=1376 tailroom=0
mac=(106,14) net=(120,40) trans=160
shinfo(txflags=0 nr_frags=0 gso(size=0 type=0 segs=0))
csum(0xffff232e ip_summed=2 complete_sw=0 valid=0 level=0)
hash(0x77e3d716 sw=1 l4=1) proto=0x86dd pkttype=0 iif=12
...
Fix this by only converting CHECKSUM_NONE packets to
CHECKSUM_UNNECESSARY by reusing __skb_incr_checksum_unnecessary. All
other checksum types are kept as-is, including CHECKSUM_COMPLETE as
fraglist packets being segmented back would have their skb->csum valid.
Fixes: 9fd1ff5d2a ("udp: Support UDP fraglist GRO/GSO.")
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d010c8031 upstream.
When rx-udp-gro-forwarding is enabled UDP packets might be GROed when
being forwarded. If such packets might land in a tunnel this can cause
various issues and udp_gro_receive makes sure this isn't the case by
looking for a matching socket. This is performed in
udp4/6_gro_lookup_skb but only in the current netns. This is an issue
with tunneled packets when the endpoint is in another netns. In such
cases the packets will be GROed at the UDP level, which leads to various
issues later on. The same thing can happen with rx-gro-list.
We saw this with geneve packets being GROed at the UDP level. In such
case gso_size is set; later the packet goes through the geneve rx path,
the geneve header is pulled, the offset are adjusted and frag_list skbs
are not adjusted with regard to geneve. When those skbs hit
skb_fragment, it will misbehave. Different outcomes are possible
depending on what the GROed skbs look like; from corrupted packets to
kernel crashes.
One example is a BUG_ON[1] triggered in skb_segment while processing the
frag_list. Because gso_size is wrong (geneve header was pulled)
skb_segment thinks there is "geneve header size" of data in frag_list,
although it's in fact the next packet. The BUG_ON itself has nothing to
do with the issue. This is only one of the potential issues.
Looking up for a matching socket in udp_gro_receive is fragile: the
lookup could be extended to all netns (not speaking about performances)
but nothing prevents those packets from being modified in between and we
could still not find a matching socket. It's OK to keep the current
logic there as it should cover most cases but we also need to make sure
we handle tunnel packets being GROed too early.
This is done by extending the checks in udp_unexpected_gso: GSO packets
lacking the SKB_GSO_UDP_TUNNEL/_CSUM bits and landing in a tunnel must
be segmented.
[1] kernel BUG at net/core/skbuff.c:4408!
RIP: 0010:skb_segment+0xd2a/0xf70
__udp_gso_segment+0xaa/0x560
Fixes: 9fd1ff5d2a ("udp: Support UDP fraglist GRO/GSO.")
Fixes: 36707061d6 ("udp: allow forwarding of plain (non-fraglisted) UDP GRO packets")
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e864d90b2 upstream.
On devices that support DASH, the current code in the "rtl_loop_wait" function
raises false alarms when DASH is disabled. This occurs because the function
attempts to wait for the DASH firmware to be ready, even though it's not
relevant in this case.
r8169 0000:0c:00.0 eth0: RTL8168ep/8111ep, 38:7c:76:49:08:d9, XID 502, IRQ 86
r8169 0000:0c:00.0 eth0: jumbo features [frames: 9194 bytes, tx checksumming: ko]
r8169 0000:0c:00.0 eth0: DASH disabled
...
r8169 0000:0c:00.0 eth0: rtl_ep_ocp_read_cond == 0 (loop: 30, delay: 10000).
This patch modifies the driver start/stop functions to skip checking the DASH
firmware status when DASH is explicitly disabled. This prevents unnecessary
delays and false alarms.
The patch has been tested on several ThinkStation P8/PX workstations.
Fixes: 0ab0c45d8a ("r8169: add handling DASH when DASH is disabled")
Signed-off-by: Atlas Yu <atlas.yu@canonical.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/20240328055152.18443-1-atlas.yu@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09ba28e1cd upstream.
The mlxbf_gige driver intermittantly encounters a NULL pointer
exception while the system is shutting down via "reboot" command.
The mlxbf_driver will experience an exception right after executing
its shutdown() method. One example of this exception is:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000070
Mem abort info:
ESR = 0x0000000096000004
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x04: level 0 translation fault
Data abort info:
ISV = 0, ISS = 0x00000004
CM = 0, WnR = 0
user pgtable: 4k pages, 48-bit VAs, pgdp=000000011d373000
[0000000000000070] pgd=0000000000000000, p4d=0000000000000000
Internal error: Oops: 96000004 [#1] SMP
CPU: 0 PID: 13 Comm: ksoftirqd/0 Tainted: G S OE 5.15.0-bf.6.gef6992a #1
Hardware name: https://www.mellanox.com BlueField SoC/BlueField SoC, BIOS 4.0.2.12669 Apr 21 2023
pstate: 20400009 (nzCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : mlxbf_gige_handle_tx_complete+0xc8/0x170 [mlxbf_gige]
lr : mlxbf_gige_poll+0x54/0x160 [mlxbf_gige]
sp : ffff8000080d3c10
x29: ffff8000080d3c10 x28: ffffcce72cbb7000 x27: ffff8000080d3d58
x26: ffff0000814e7340 x25: ffff331cd1a05000 x24: ffffcce72c4ea008
x23: ffff0000814e4b40 x22: ffff0000814e4d10 x21: ffff0000814e4128
x20: 0000000000000000 x19: ffff0000814e4a80 x18: ffffffffffffffff
x17: 000000000000001c x16: ffffcce72b4553f4 x15: ffff80008805b8a7
x14: 0000000000000000 x13: 0000000000000030 x12: 0101010101010101
x11: 7f7f7f7f7f7f7f7f x10: c2ac898b17576267 x9 : ffffcce720fa5404
x8 : ffff000080812138 x7 : 0000000000002e9a x6 : 0000000000000080
x5 : ffff00008de3b000 x4 : 0000000000000000 x3 : 0000000000000001
x2 : 0000000000000000 x1 : 0000000000000000 x0 : 0000000000000000
Call trace:
mlxbf_gige_handle_tx_complete+0xc8/0x170 [mlxbf_gige]
mlxbf_gige_poll+0x54/0x160 [mlxbf_gige]
__napi_poll+0x40/0x1c8
net_rx_action+0x314/0x3a0
__do_softirq+0x128/0x334
run_ksoftirqd+0x54/0x6c
smpboot_thread_fn+0x14c/0x190
kthread+0x10c/0x110
ret_from_fork+0x10/0x20
Code: 8b070000 f9000ea0 f95056c0 f86178a1 (b9407002)
---[ end trace 7cc3941aa0d8e6a4 ]---
Kernel panic - not syncing: Oops: Fatal exception in interrupt
Kernel Offset: 0x4ce722520000 from 0xffff800008000000
PHYS_OFFSET: 0x80000000
CPU features: 0x000005c1,a3330e5a
Memory Limit: none
---[ end Kernel panic - not syncing: Oops: Fatal exception in interrupt ]---
During system shutdown, the mlxbf_gige driver's shutdown() is always executed.
However, the driver's stop() method will only execute if networking interface
configuration logic within the Linux distribution has been setup to do so.
If shutdown() executes but stop() does not execute, NAPI remains enabled
and this can lead to an exception if NAPI is scheduled while the hardware
interface has only been partially deinitialized.
The networking interface managed by the mlxbf_gige driver must be properly
stopped during system shutdown so that IFF_UP is cleared, the hardware
interface is put into a clean state, and NAPI is fully deinitialized.
Fixes: f92e1869d7 ("Add Mellanox BlueField Gigabit Ethernet driver")
Signed-off-by: David Thompson <davthompson@nvidia.com>
Link: https://lore.kernel.org/r/20240325210929.25362-1-davthompson@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fd819ad3ec upstream.
When the ax25 device is detaching, the ax25_dev_device_down()
calls ax25_ds_del_timer() to cleanup the slave_timer. When
the timer handler is running, the ax25_ds_del_timer() that
calls del_timer() in it will return directly. As a result,
the use-after-free bugs could happen, one of the scenarios
is shown below:
(Thread 1) | (Thread 2)
| ax25_ds_timeout()
ax25_dev_device_down() |
ax25_ds_del_timer() |
del_timer() |
ax25_dev_put() //FREE |
| ax25_dev-> //USE
In order to mitigate bugs, when the device is detaching, use
timer_shutdown_sync() to stop the timer.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240329015023.9223-1-duoming@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d91ef1e1b5 upstream.
Jianguo Wu reported another bind() regression introduced by bhash2.
Calling bind() for the following 3 addresses on the same port, the
3rd one should fail but now succeeds.
1. 0.0.0.0 or ::ffff:0.0.0.0
2. [::] w/ IPV6_V6ONLY
3. IPv4 non-wildcard address or v4-mapped-v6 non-wildcard address
The first two bind() create tb2 like this:
bhash2 -> tb2(:: w/ IPV6_V6ONLY) -> tb2(0.0.0.0)
The 3rd bind() will match with the IPv6 only wildcard address bucket
in inet_bind2_bucket_match_addr_any(), however, no conflicting socket
exists in the bucket. So, inet_bhash2_conflict() will returns false,
and thus, inet_bhash2_addr_any_conflict() returns false consequently.
As a result, the 3rd bind() bypasses conflict check, which should be
done against the IPv4 wildcard address bucket.
So, in inet_bhash2_addr_any_conflict(), we must iterate over all buckets.
Note that we cannot add ipv6_only flag for inet_bind2_bucket as it
would confuse the following patetrn.
1. [::] w/ SO_REUSE{ADDR,PORT} and IPV6_V6ONLY
2. [::] w/ SO_REUSE{ADDR,PORT}
3. IPv4 non-wildcard address or v4-mapped-v6 non-wildcard address
The first bind() would create a bucket with ipv6_only flag true,
the second bind() would add the [::] socket into the same bucket,
and the third bind() could succeed based on the wrong assumption
that ipv6_only bucket would not conflict with v4(-mapped-v6) address.
Fixes: 28044fc1d4 ("net: Add a bhash2 table hashed by port and address")
Diagnosed-by: Jianguo Wu <wujianguo106@163.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20240326204251.51301-3-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 31974122cf upstream.
The netdev CI runs in a VM and captures serial, so stdout and
stderr get combined. Because there's a missing new line in
stderr the test ends up corrupting KTAP:
# Successok 1 selftests: net: reuseaddr_conflict
which should have been:
# Success
ok 1 selftests: net: reuseaddr_conflict
Fixes: 422d8dc6fd ("selftest: add a reuseaddr test")
Reviewed-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Link: https://lore.kernel.org/r/20240329160559.249476-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea2a1cfc3b upstream.
Commit 73d9629e1c ("i40e: Do not allow untrusted VF to remove
administratively set MAC") fixed an issue where untrusted VF was
allowed to remove its own MAC address although this was assigned
administratively from PF. Unfortunately the introduced check
is wrong because it causes that MAC filters for other MAC addresses
including multi-cast ones are not removed.
<snip>
if (ether_addr_equal(addr, vf->default_lan_addr.addr) &&
i40e_can_vf_change_mac(vf))
was_unimac_deleted = true;
else
continue;
if (i40e_del_mac_filter(vsi, al->list[i].addr)) {
...
</snip>
The else path with `continue` effectively skips any MAC filter
removal except one for primary MAC addr when VF is allowed to do so.
Fix the check condition so the `continue` is only done for primary
MAC address.
Fixes: 73d9629e1c ("i40e: Do not allow untrusted VF to remove administratively set MAC")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240329180638.211412-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8edfc7a40e upstream.
ice_port_vlan_on/off() was introduced in commit 2946204b3f ("ice:
implement bridge port vlan"). But ice_port_vlan_on() incorrectly assigns
ena_rx_filtering to inner_vlan_ops in DVM mode.
This causes an error when rx_filtering cannot be enabled in legacy mode.
Reproducer:
echo 1 > /sys/class/net/$PF/device/sriov_numvfs
ip link set $PF vf 0 spoofchk off trust on vlan 3
dmesg:
ice 0000:41:00.0: failed to enable Rx VLAN filtering for VF 0 VSI 9 during VF rebuild, error -95
Fixes: 2946204b3f ("ice: implement bridge port vlan")
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ed4cccef64 upstream.
If packets are GROed with fraglist they might be segmented later on and
continue their journey in the stack. In skb_segment_list those skbs can
be reused as-is. This is an issue as their destructor was removed in
skb_gro_receive_list but not the reference to their socket, and then
they can't be orphaned. Fix this by also removing the reference to the
socket.
For example this could be observed,
kernel BUG at include/linux/skbuff.h:3131! (skb_orphan)
RIP: 0010:ip6_rcv_core+0x11bc/0x19a0
Call Trace:
ipv6_list_rcv+0x250/0x3f0
__netif_receive_skb_list_core+0x49d/0x8f0
netif_receive_skb_list_internal+0x634/0xd40
napi_complete_done+0x1d2/0x7d0
gro_cell_poll+0x118/0x1f0
A similar construction is found in skb_gro_receive, apply the same
change there.
Fixes: 5e10da5385 ("skbuff: allow 'slow_gro' for skb carring sock reference")
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0fb101be97 upstream.
UDP tunnel packets can't be GRO in-between their endpoints as this
causes different issues. The UDP GRO fwd vxlan tests were relying on
this and their expectations have to be fixed.
We keep both vxlan tests and expected no GRO from happening. The vxlan
UDP GRO bench test was removed as it's not providing any valuable
information now.
Fixes: a062260a9d ("selftests: net: add UDP GRO forwarding self-tests")
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cbc17e7802 upstream.
Setting mac_managed_pm during interface up is too late.
In situations where the link is not brought up yet and the system suspends
the regular PHY power management will run. Since the FEC ETHEREN control
bit is cleared (automatically) on suspend the controller is off in resume.
When the regular PHY power management resume path runs in this context it
will write to the MII_DATA register but nothing will be transmitted on the
MDIO bus.
This can be observed by the following log:
fec 5b040000.ethernet eth0: MDIO read timeout
Microchip LAN87xx T1 5b040000.ethernet-1:04: PM: dpm_run_callback(): mdio_bus_phy_resume+0x0/0xc8 returns -110
Microchip LAN87xx T1 5b040000.ethernet-1:04: PM: failed to resume: error -110
The data written will however remain in the MII_DATA register.
When the link later is set to administrative up it will trigger a call to
fec_restart() which will restore the MII_SPEED register. This triggers the
quirk explained in f166f890c8 ("net: ethernet: fec: Replace interrupt
driven MDIO with polled IO") causing an extra MII_EVENT.
This extra event desynchronizes all the MDIO register reads, causing them
to complete too early. Leading all reads to read as 0 because
fec_enet_mdio_wait() returns too early.
When a Microchip LAN8700R PHY is connected to the FEC, the 0 reads causes
the PHY to be initialized incorrectly and the PHY will not transmit any
ethernet signal in this state. It cannot be brought out of this state
without a power cycle of the PHY.
Fixes: 557d5dc83f ("net: fec: use mac-managed PHY PM")
Closes: https://lore.kernel.org/netdev/1f45bdbe-eab1-4e59-8f24-add177590d27@actia.se/
Signed-off-by: Wei Fang <wei.fang@nxp.com>
[jernberg: commit message]
Signed-off-by: John Ernberg <john.ernberg@actia.se>
Link: https://lore.kernel.org/r/20240328155909.59613-2-john.ernberg@actia.se
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit de99e1ea3a upstream.
There are 2 issues with the blamed commit.
1. When the phy is initialized, it would enable the disabled of UDPv4
checksums. The UDPv6 checksum is already enabled by default. So when
1-step is configured then it would clear these flags.
2. After the 1-step is configured, then if 2-step is configured then the
1-step would be still configured because it is not clearing the flag.
So the sync frames will still have origin timestamps set.
Fix this by reading first the value of the register and then
just change bit 12 as this one determines if the timestamp needs to
be inserted in the frame, without changing any other bits.
Fixes: ece1950283 ("net: phy: micrel: 1588 support for LAN8814 phy")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Divya Koppera <divya.koppera@microchip.com>
Link: https://lore.kernel.org/r/20240402071634.2483524-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b3da86d432 upstream.
The driver should ensure that same priority is not mapped to multiple
rx queues. From DesignWare Cores Ethernet Quality-of-Service
Databook, section 17.1.29 MAC_RxQ_Ctrl2:
"[...]The software must ensure that the content of this field is
mutually exclusive to the PSRQ fields for other queues, that is,
the same priority is not mapped to multiple Rx queues[...]"
Previously rx_queue_priority() function was:
- clearing all priorities from a queue
- adding new priorities to that queue
After this patch it will:
- first assign new priorities to a queue
- then remove those priorities from all other queues
- keep other priorities previously assigned to that queue
Fixes: a8f5102af2 ("net: stmmac: TX and RX queue priority configuration")
Fixes: 2142754f8b ("net: stmmac: Add MAC related callbacks for XGMAC2")
Signed-off-by: Piotr Wejman <piotrwejman90@gmail.com>
Link: https://lore.kernel.org/r/20240401192239.33942-1-piotrwejman90@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c36a15673 upstream.
When zapping a table entry in stage2_try_break_pte(), we issue range
TLB invalidation for the region that was mapped by the table. However,
we neglect to align the base address down to the granule size and so
if we ended up reaching the table entry via a misaligned address then
we will accidentally skip invalidation for some prefix of the affected
address range.
Align 'ctx->addr' down to the granule size when performing TLB
invalidation for an unmapped table in stage2_try_break_pte().
Cc: Raghavendra Rao Ananta <rananta@google.com>
Cc: Gavin Shan <gshan@redhat.com>
Cc: Shaoqin Huang <shahuang@redhat.com>
Cc: Quentin Perret <qperret@google.com>
Fixes: defc8cc7ab ("KVM: arm64: Invalidate the table entries upon a range")
Signed-off-by: Will Deacon <will@kernel.org>
Reviewed-by: Shaoqin Huang <shahuang@redhat.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240327124853.11206-5-will@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0e11073247 upstream.
The srso_alias_untrain_ret() dummy thunk in the !CONFIG_MITIGATION_SRSO
case is there only for the altenative in CALL_UNTRAIN_RET to have
a symbol to resolve.
However, testing with kernels which don't have CONFIG_MITIGATION_SRSO
enabled, leads to the warning in patch_return() to fire:
missing return thunk: srso_alias_untrain_ret+0x0/0x10-0x0: eb 0e 66 66 2e
WARNING: CPU: 0 PID: 0 at arch/x86/kernel/alternative.c:826 apply_returns (arch/x86/kernel/alternative.c:826
Put in a plain "ret" there so that gcc doesn't put a return thunk in
in its place which special and gets checked.
In addition:
ERROR: modpost: "srso_alias_untrain_ret" [arch/x86/kvm/kvm-amd.ko] undefined!
make[2]: *** [scripts/Makefile.modpost:145: Module.symvers] Chyba 1
make[1]: *** [/usr/src/linux-6.8.3/Makefile:1873: modpost] Chyba 2
make: *** [Makefile:240: __sub-make] Chyba 2
since !SRSO builds would use the dummy return thunk as reported by
petr.pisar@atlas.cz, https://bugzilla.kernel.org/show_bug.cgi?id=218679.
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202404020901.da75a60f-oliver.sang@intel.com
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/all/202404020901.da75a60f-oliver.sang@intel.com/
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1bc83a019b upstream.
Hook unregistration is deferred to the commit phase, same occurs with
hook updates triggered by the table dormant flag. When both commands are
combined, this results in deleting a basechain while leaving its hook
still registered in the core.
Fixes: 179d9ba555 ("netfilter: nf_tables: fix table flag updates")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 24225011d8 upstream.
nft_unregister_flowtable_type() within nf_flow_inet_module_exit() can
concurrent with __nft_flowtable_type_get() within nf_tables_newflowtable().
And thhere is not any protection when iterate over nf_tables_flowtables
list in __nft_flowtable_type_get(). Therefore, there is pertential
data-race of nf_tables_flowtables list entry.
Use list_for_each_entry_rcu() to iterate over nf_tables_flowtables list
in __nft_flowtable_type_get(), and use rcu_read_lock() in the caller
nft_flowtable_type_get() to protect the entire type query process.
Fixes: 3b49e2e94e ("netfilter: nf_tables: add flow table netlink frontend")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 4535e1a417 upstream.
The original version of the mitigation would patch in the calls to the
untraining routines directly. That is, the alternative() in UNTRAIN_RET
will patch in the CALL to srso_alias_untrain_ret() directly.
However, even if commit e7c25c441e ("x86/cpu: Cleanup the untrain
mess") meant well in trying to clean up the situation, due to micro-
architectural reasons, the untraining routine srso_alias_untrain_ret()
must be the target of a CALL instruction and not of a JMP instruction as
it is done now.
Reshuffle the alternative macros to accomplish that.
Fixes: e7c25c441e ("x86/cpu: Cleanup the untrain mess")
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b32a09ea7c upstream.
Commit 82dfb540ae ("VSOCK: Add virtio vsock vsockmon hooks") added
virtio_transport_deliver_tap_pkt() for handing packets to the
vsockmon device. However, in virtio_transport_send_pkt_work(),
the function is called before actually sending the packet (i.e.
before placing it in the virtqueue with virtqueue_add_sgs() and checking
whether it returned successfully).
Queuing the packet in the virtqueue can fail even multiple times.
However, in virtio_transport_deliver_tap_pkt() we deliver the packet
to the monitoring tap interface only the first time we call it.
This certainly avoids seeing the same packet replicated multiple times
in the monitoring interface, but it can show the packet sent with the
wrong timestamp or even before we succeed to queue it in the virtqueue.
Move virtio_transport_deliver_tap_pkt() after calling virtqueue_add_sgs()
and making sure it returned successfully.
Fixes: 82dfb540ae ("VSOCK: Add virtio vsock vsockmon hooks")
Cc: stable@vge.kernel.org
Signed-off-by: Marco Pinna <marco.pinn95@gmail.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/r/20240329161259.411751-1-marco.pinn95@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c0de6ab920 upstream.
mana_get_rxbuf_cfg() aligns the RX buffer's DMA datasize to be
multiple of 64. So a packet slightly bigger than mtu+14, say 1536,
can be received and cause skb_over_panic.
Sample dmesg:
[ 5325.237162] skbuff: skb_over_panic: text:ffffffffc043277a len:1536 put:1536 head:ff1100018b517000 data:ff1100018b517100 tail:0x700 end:0x6ea dev:<NULL>
[ 5325.243689] ------------[ cut here ]------------
[ 5325.245748] kernel BUG at net/core/skbuff.c:192!
[ 5325.247838] invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
[ 5325.258374] RIP: 0010:skb_panic+0x4f/0x60
[ 5325.302941] Call Trace:
[ 5325.304389] <IRQ>
[ 5325.315794] ? skb_panic+0x4f/0x60
[ 5325.317457] ? asm_exc_invalid_op+0x1f/0x30
[ 5325.319490] ? skb_panic+0x4f/0x60
[ 5325.321161] skb_put+0x4e/0x50
[ 5325.322670] mana_poll+0x6fa/0xb50 [mana]
[ 5325.324578] __napi_poll+0x33/0x1e0
[ 5325.326328] net_rx_action+0x12e/0x280
As discussed internally, this alignment is not necessary. To fix
this bug, remove it from the code. So oversized packets will be
marked as CQE_RX_TRUNCATED by NIC, and dropped.
Cc: stable@vger.kernel.org
Fixes: 2fbbd712ba ("net: mana: Enable RX path to handle various MTU sizes")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Link: https://lore.kernel.org/r/1712087316-20886-1-git-send-email-haiyangz@microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e91bb99b9 upstream.
After the commit d2689b6a86 ("net: usb: ax88179_178a: avoid two
consecutive device resets"), reset is not executed from bind operation and
mac address is not read from the device registers or the devicetree at that
moment. Since the check to configure if the assigned mac address is random
or not for the interface, happens after the bind operation from
usbnet_probe, the interface keeps configured as random address, although the
address is correctly read and set during open operation (the only reset
now).
In order to keep only one reset for the device and to avoid the interface
always configured as random address, after reset, configure correctly the
suitable field from the driver, if the mac address is read successfully from
the device registers or the devicetree. Take into account if a locally
administered address (random) was previously stored.
cc: stable@vger.kernel.org # 6.6+
Fixes: d2689b6a86 ("net: usb: ax88179_178a: avoid two consecutive device resets")
Reported-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240403132158.344838-1-jtornosm@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 62fc3357e0 upstream.
cp might be null, calling cp->cp_conn would produce null dereference
[Simon Horman adds:]
Analysis:
* cp is a parameter of __rds_rdma_map and is not reassigned.
* The following call-sites pass a NULL cp argument to __rds_rdma_map()
- rds_get_mr()
- rds_get_mr_for_dest
* Prior to the code above, the following assumes that cp may be NULL
(which is indicative, but could itself be unnecessary)
trans_private = rs->rs_transport->get_mr(
sg, nents, rs, &mr->r_key, cp ? cp->cp_conn : NULL,
args->vec.addr, args->vec.bytes,
need_odp ? ODP_ZEROBASED : ODP_NOT_NEEDED);
* The code modified by this patch is guarded by IS_ERR(trans_private),
where trans_private is assigned as per the previous point in this analysis.
The only implementation of get_mr that I could locate is rds_ib_get_mr()
which can return an ERR_PTR if the conn (4th) argument is NULL.
* ret is set to PTR_ERR(trans_private).
rds_ib_get_mr can return ERR_PTR(-ENODEV) if the conn (4th) argument is NULL.
Thus ret may be -ENODEV in which case the code in question will execute.
Conclusion:
* cp may be NULL at the point where this patch adds a check;
this patch does seem to address a possible bug
Fixes: c055fc00c0 ("net/rds: fix WARNING in rds_conn_connect_if_down")
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Mahmoud Adam <mngyadam@amazon.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240326153132.55580-1-mngyadam@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0d459e2ffb upstream.
The commit mutex should not be released during the critical section
between nft_gc_seq_begin() and nft_gc_seq_end(), otherwise, async GC
worker could collect expired objects and get the released commit lock
within the same GC sequence.
nf_tables_module_autoload() temporarily releases the mutex to load
module dependencies, then it goes back to replay the transaction again.
Move it at the end of the abort phase after nft_gc_seq_end() is called.
Cc: stable@vger.kernel.org
Fixes: 720344340f ("netfilter: nf_tables: GC transaction race with abort path")
Reported-by: Kuan-Ting Chen <hexrabbit@devco.re>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a45e688957 upstream.
Unlike early commit path stage which triggers a call to abort, an
explicit release of the batch is required on abort, otherwise mutex is
released and commit_list remains in place.
Add WARN_ON_ONCE to ensure commit_list is empty from the abort path
before releasing the mutex.
After this patch, commit_list is always assumed to be empty before
grabbing the mutex, therefore
03c1f1ef15 ("netfilter: Cleanup nft_net->module_list from nf_tables_exit_net()")
only needs to release the pending modules for registration.
Cc: stable@vger.kernel.org
Fixes: c0391b6ab8 ("netfilter: nf_tables: missing validation from the abort path")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7835fcfd13 upstream.
struct hci_dev members conn_info_max_age, conn_info_min_age,
le_conn_max_interval, le_conn_min_interval, le_adv_max_interval,
and le_adv_min_interval can be modified from the HCI core code, as well
through debugfs.
The debugfs implementation, that's only available to privileged users,
will check for boundaries, making sure that the minimum value being set
is strictly above the maximum value that already exists, and vice-versa.
However, as both minimum and maximum values can be changed concurrently
to us modifying them, we need to make sure that the value we check is
the value we end up using.
For example, with ->conn_info_max_age set to 10, conn_info_min_age_set()
gets called from vfs handlers to set conn_info_min_age to 8.
In conn_info_min_age_set(), this goes through:
if (val == 0 || val > hdev->conn_info_max_age)
return -EINVAL;
Concurrently, conn_info_max_age_set() gets called to set to set the
conn_info_max_age to 7:
if (val == 0 || val > hdev->conn_info_max_age)
return -EINVAL;
That check will also pass because we used the old value (10) for
conn_info_max_age.
After those checks that both passed, the struct hci_dev access
is mutex-locked, disabling concurrent access, but that does not matter
because the invalid value checks both passed, and we'll end up with
conn_info_min_age = 8 and conn_info_max_age = 7
To fix this problem, we need to lock the structure access before so the
check and assignment are not interrupted.
This fix was originally devised by the BassCheck[1] team, and
considered the problem to be an atomicity one. This isn't the case as
there aren't any concerns about the variable changing while we check it,
but rather after we check it parallel to another change.
This patch fixes CVE-2024-24858 and CVE-2024-24857.
[1] https://sites.google.com/view/basscheck/
Co-developed-by: Gui-Dong Han <2045gemini@gmail.com>
Signed-off-by: Gui-Dong Han <2045gemini@gmail.com>
Link: https://lore.kernel.org/linux-bluetooth/20231222161317.6255-1-2045gemini@gmail.com/
Link: https://nvd.nist.gov/vuln/detail/CVE-2024-24858
Link: https://lore.kernel.org/linux-bluetooth/20231222162931.6553-1-2045gemini@gmail.com/
Link: https://lore.kernel.org/linux-bluetooth/20231222162310.6461-1-2045gemini@gmail.com/
Link: https://nvd.nist.gov/vuln/detail/CVE-2024-24857
Fixes: 31ad169148 ("Bluetooth: Add conn info lifetime parameters to debugfs")
Fixes: 729a1051da ("Bluetooth: Expose default LE advertising interval via debugfs")
Fixes: 71c3b60ec6 ("Bluetooth: Move BR/EDR debugfs file creation into hci_debugfs.c")
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c569242cd4 upstream.
We have a BT headset (Lenovo Thinkplus XT99), the pairing and
connecting has no problem, once this headset is paired, bluez will
remember this device and will auto re-connect it whenever the device
is powered on. The auto re-connecting works well with Windows and
Android, but with Linux, it always fails. Through debugging, we found
at the rfcomm connection stage, the bluetooth stack reports
"Connection refused - security block (0x0003)".
For this device, the re-connecting negotiation process is different
from other BT headsets, it sends the Link_KEY_REQUEST command before
the CONNECT_REQUEST completes, and it doesn't send ENCRYPT_CHANGE
command during the negotiation. When the device sends the "connect
complete" to hci, the ev->encr_mode is 1.
So here in the conn_complete_evt(), if ev->encr_mode is 1, link type
is ACL and HCI_CONN_ENCRYPT is not set, we set HCI_CONN_ENCRYPT to
this conn, and update conn->enc_key_size accordingly.
After this change, this BT headset could re-connect with Linux
successfully. This is the btmon log after applying the patch, after
receiving the "Connect Complete" with "Encryption: Enabled", will send
the command to read encryption key size:
> HCI Event: Connect Request (0x04) plen 10
Address: 8C:3C:AA:D8:11:67 (OUI 8C-3C-AA)
Class: 0x240404
Major class: Audio/Video (headset, speaker, stereo, video, vcr)
Minor class: Wearable Headset Device
Rendering (Printing, Speaker)
Audio (Speaker, Microphone, Headset)
Link type: ACL (0x01)
...
> HCI Event: Link Key Request (0x17) plen 6
Address: 8C:3C:AA:D8:11:67 (OUI 8C-3C-AA)
< HCI Command: Link Key Request Reply (0x01|0x000b) plen 22
Address: 8C:3C:AA:D8:11:67 (OUI 8C-3C-AA)
Link key: ${32-hex-digits-key}
...
> HCI Event: Connect Complete (0x03) plen 11
Status: Success (0x00)
Handle: 256
Address: 8C:3C:AA:D8:11:67 (OUI 8C-3C-AA)
Link type: ACL (0x01)
Encryption: Enabled (0x01)
< HCI Command: Read Encryption Key... (0x05|0x0008) plen 2
Handle: 256
< ACL Data TX: Handle 256 flags 0x00 dlen 10
L2CAP: Information Request (0x0a) ident 1 len 2
Type: Extended features supported (0x0002)
> HCI Event: Command Complete (0x0e) plen 7
Read Encryption Key Size (0x05|0x0008) ncmd 1
Status: Success (0x00)
Handle: 256
Key size: 16
Cc: stable@vger.kernel.org
Link: https://github.com/bluez/bluez/issues/704
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 39646f29b1 upstream.
Some Bluetooth controllers lack persistent storage for the device
address and instead one can be provided by the boot firmware using the
'local-bd-address' devicetree property.
The Bluetooth devicetree bindings clearly states that the address should
be specified in little-endian order, but due to a long-standing bug in
the Qualcomm driver which reversed the address some boot firmware has
been providing the address in big-endian order instead.
Add a new quirk that can be set on platforms with broken firmware and
use it to reverse the address when parsing the property so that the
underlying driver bug can be fixed.
Fixes: 5c0a1001c8 ("Bluetooth: hci_qca: Add helper to set device address")
Cc: stable@vger.kernel.org # 5.1
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 77f45cca8b upstream.
The WCN6855 firmware on the Lenovo ThinkPad X13s expects the Bluetooth
device address in big-endian order when setting it using the
EDL_WRITE_BD_ADDR_OPCODE command.
Presumably, this is the case for all non-ROME devices which all use the
EDL_WRITE_BD_ADDR_OPCODE command for this (unlike the ROME devices which
use a different command and expect the address in little-endian order).
Reverse the little-endian address before setting it to make sure that
the address can be configured using tools like btmgmt or using the
'local-bd-address' devicetree property.
Note that this can potentially break systems with boot firmware which
has started relying on the broken behaviour and is incorrectly passing
the address via devicetree in big-endian order.
The only device affected by this should be the WCN3991 used in some
Chromebooks. As ChromeOS updates the kernel and devicetree in lockstep,
the new 'qcom,local-bd-address-broken' property can be used to determine
if the firmware is buggy so that the underlying driver bug can be fixed
without breaking backwards compatibility.
Set the HCI_QUIRK_BDADDR_PROPERTY_BROKEN quirk for such platforms so
that the address is reversed when parsing the address property.
Fixes: 5c0a1001c8 ("Bluetooth: hci_qca: Add helper to set device address")
Cc: stable@vger.kernel.org # 5.1
Cc: Balakrishna Godavarthi <quic_bgodavar@quicinc.com>
Cc: Matthias Kaehlcke <mka@chromium.org>
Tested-by: Nikita Travkin <nikita@trvn.ru> # sc7180
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e12e28009e upstream.
Several Qualcomm Bluetooth controllers lack persistent storage for the
device address and instead one can be provided by the boot firmware
using the 'local-bd-address' devicetree property.
The Bluetooth bindings clearly states that the address should be
specified in little-endian order, but due to a long-standing bug in the
Qualcomm driver which reversed the address some boot firmware has been
providing the address in big-endian order instead.
The boot firmware in SC7180 Trogdor Chromebooks is known to be affected
so mark the 'local-bd-address' property as broken to maintain backwards
compatibility with older firmware when fixing the underlying driver bug.
Note that ChromeOS always updates the kernel and devicetree in lockstep
so that there is no need to handle backwards compatibility with older
devicetrees.
Fixes: 7ec3e67307 ("arm64: dts: qcom: sc7180-trogdor: add initial trogdor and lazor dt")
Cc: stable@vger.kernel.org # 5.10
Cc: Rob Clark <robdclark@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4790a73ace upstream.
This reverts commit 7dcd3e014a.
Qualcomm Bluetooth controllers like WCN6855 do not have persistent
storage for the Bluetooth address and must therefore start as
unconfigured to allow the user to set a valid address unless one has
been provided by the boot firmware in the devicetree.
A recent change snuck into v6.8-rc7 and incorrectly started marking the
default (non-unique) address as valid. This specifically also breaks the
Bluetooth setup for some user of the Lenovo ThinkPad X13s.
Note that this is the second time Qualcomm breaks the driver this way
and that this was fixed last year by commit 6945795bc8 ("Bluetooth:
fix use-bdaddr-property quirk"), which also has some further details.
Fixes: 7dcd3e014a ("Bluetooth: hci_qca: Set BDA quirk bit if fwnode exists in DT")
Cc: stable@vger.kernel.org # 6.8
Cc: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reported-by: Clayton Craft <clayton@craftyguy.net>
Tested-by: Clayton Craft <clayton@craftyguy.net>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8cb4a9a82b upstream.
Add CPUID_LNX_5 to track cpufeatures' word 21, and add the appropriate
compile-time assert in KVM to prevent direct lookups on the features in
CPUID_LNX_5. KVM uses X86_FEATURE_* flags to manage guest CPUID, and so
must translate features that are scattered by Linux from the Linux-defined
bit to the hardware-defined bit, i.e. should never try to directly access
scattered features in guest CPUID.
Opportunistically add NR_CPUID_WORDS to enum cpuid_leafs, along with a
compile-time assert in KVM's CPUID infrastructure to ensure that future
additions update cpuid_leafs along with NCAPINTS.
No functional change intended.
Fixes: 7f274e609f ("x86/cpufeatures: Add new word for scattered features")
Cc: Sandipan Das <sandipan.das@amd.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 37801a36b4 upstream.
In case kern_mount() fails and returns an error pointer return in the
error branch instead of continuing and dereferencing the error pointer.
While on it drop the never read static variable selinuxfs_mount.
Cc: stable@vger.kernel.org
Fixes: 0619f0f5e3 ("selinux: wrap selinuxfs state")
Signed-off-by: Christian Göttsche <cgzones@googlemail.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e89c928bed upstream.
Programming PMU events in the host that count during guest execution is
a feature supported by perf, e.g.
perf stat -e cpu_cycles:G ./lkvm run
While this works for VHE, the guest/host event bitmaps are not carried
through to the hypervisor in the nVHE configuration. Make
kvm_pmu_update_vcpu_events() conditional on whether or not _hardware_
supports PMUv3 rather than if the vCPU as vPMU enabled.
Cc: stable@vger.kernel.org
Fixes: 84d751a019 ("KVM: arm64: Pass pmu events to hyp via vcpu")
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240305184840.636212-3-oliver.upton@linux.dev
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e936e9871 upstream.
The reads to APLIC in_clrip[x] registers returns rectified input values
of the interrupt sources.
A rectified input value of an interrupt source is defined by the section
"4.5.2 Source configurations (sourcecfg[1]–sourcecfg[1023])" of the
RISC-V AIA specification as:
rectified input value = (incoming wire value) XOR (source is inverted)
Update the riscv_aplic_input() implementation to match the above.
Cc: stable@vger.kernel.org
Fixes: 74967aa208 ("RISC-V: KVM: Add in-kernel emulation of AIA APLIC")
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
Link: https://lore.kernel.org/r/20240321085041.1955293-3-apatel@ventanamicro.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d8dd9f113e upstream.
The writes to setipnum_le/be register for APLIC in MSI-mode have special
consideration for level-triggered interrupts as-per the section "4.9.2
Special consideration for level-sensitive interrupt sources" of the RISC-V
AIA specification.
Particularly, the below text from the RISC-V AIA specification defines
the behaviour of writes to setipnum_le/be register for level-triggered
interrupts:
"A second option is for the interrupt service routine to write the
APLIC’s source identity number for the interrupt to the domain’s
setipnum register just before exiting. This will cause the interrupt’s
pending bit to be set to one again if the source is still asserting
an interrupt, but not if the source is not asserting an interrupt."
Fix setipnum_le/be write emulation for in-kernel APLIC by implementing
the above behaviour in aplic_write_pending() function.
Cc: stable@vger.kernel.org
Fixes: 74967aa208 ("RISC-V: KVM: Add in-kernel emulation of AIA APLIC")
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
Link: https://lore.kernel.org/r/20240321085041.1955293-2-apatel@ventanamicro.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b34490879b upstream.
When an interrupt is requested, a procfs directory is created under
"/proc/irq/<irqnum>/<label>" where <label> is the string passed to one of
the request_irq() variants.
What follows is that the string must not contain the "/" character or
the procfs mkdir operation will fail. We don't have such constraints for
GPIO consumer labels which are used verbatim as interrupt labels for
GPIO irqs. We must therefore sanitize the consumer string before
requesting the interrupt.
Let's replace all "/" with ":".
Cc: stable@vger.kernel.org
Reported-by: Stefan Wahren <wahrenst@gmx.net>
Closes: https://lore.kernel.org/linux-gpio/39fe95cb-aa83-4b8b-8cab-63947a726754@gmx.net/
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1102f9f85b ]
As mentioned in commit 397586506c ("modpost: Add '.ltext' and
'.ltext.*' to TEXT_SECTIONS"), modpost can result in a segmentation
fault due to a NULL pointer dereference in default_mismatch_handler().
find_tosym() can return the original symbol pointer instead of NULL
if a better one is not found.
This fixes the reported segmentation fault.
Fixes: a23e7584ec ("modpost: unify 'sym' and 'to' in default_mismatch_handler()")
Reported-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4074532758 ]
Modify modpost to use binary search for converting addresses back
into symbol references. Previously it used linear search.
This change saves a few seconds of wall time for defconfig builds,
but can save several minutes on allyesconfigs.
Before:
$ make LLVM=1 -j128 allyesconfig vmlinux -s KCFLAGS="-Wno-error"
$ time scripts/mod/modpost -M -m -a -N -o vmlinux.symvers vmlinux.o
198.38user 1.27system 3:19.71elapsed
After:
$ make LLVM=1 -j128 allyesconfig vmlinux -s KCFLAGS="-Wno-error"
$ time scripts/mod/modpost -M -m -a -N -o vmlinux.symvers vmlinux.o
11.91user 0.85system 0:12.78elapsed
Signed-off-by: Jack Brennen <jbrennen@google.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Stable-dep-of: 1102f9f85b ("modpost: do not make find_tosym() return NULL")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 598c2fafc0 ]
Currently, the LBR code assumes that LBR Freeze is supported on all processors
when X86_FEATURE_AMD_LBR_V2 is available i.e. CPUID leaf 0x80000022[EAX]
bit 1 is set. This is incorrect as the availability of the feature is
additionally dependent on CPUID leaf 0x80000022[EAX] bit 2 being set,
which may not be set for all Zen 4 processors.
Define a new feature bit for LBR and PMC freeze and set the freeze enable bit
(FLBRI) in DebugCtl (MSR 0x1d9) conditionally.
It should still be possible to use LBR without freeze for profile-guided
optimization of user programs by using an user-only branch filter during
profiling. When the user-only filter is enabled, branches are no longer
recorded after the transition to CPL 0 upon PMI arrival. When branch
entries are read in the PMI handler, the branch stack does not change.
E.g.
$ perf record -j any,u -e ex_ret_brn_tkn ./workload
Since the feature bit is visible under flags in /proc/cpuinfo, it can be
used to determine the feasibility of use-cases which require LBR Freeze
to be supported by the hardware such as profile-guided optimization of
kernels.
Fixes: ca5b7c0d96 ("perf/x86/amd/lbr: Add LbrExtV2 branch record support")
Signed-off-by: Sandipan Das <sandipan.das@amd.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/69a453c97cfd11c6f2584b19f937fe6df741510f.1711091584.git.sandipan.das@amd.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 978b63f746 ]
For fiemap we recently stopped locking the target extent range for the
whole duration of the fiemap call, in order to avoid a deadlock in a
scenario where the fiemap buffer happens to be a memory mapped range of
the same file. This use case is very unlikely to be useful in practice but
it may be triggered by fuzz testing (syzbot, etc).
This however introduced a race that makes us miss delalloc ranges for
file regions that are currently holes, so the caller of fiemap will not
be aware that there's data for some file regions. This can be quite
serious for some use cases - for example in coreutils versions before 9.0,
the cp program used fiemap to detect holes and data in the source file,
copying only regions with data (extents or delalloc) from the source file
to the destination file in order to preserve holes (see the documentation
for its --sparse command line option). This means that if cp was used
with a source file that had delalloc in a hole, the destination file could
end up without that data, which is effectively a data loss issue, if it
happened to hit the race described below.
The race happens like this:
1) Fiemap is called, without the FIEMAP_FLAG_SYNC flag, for a file that
has delalloc in the file range [64M, 65M[, which is currently a hole;
2) Fiemap locks the inode in shared mode, then starts iterating the
inode's subvolume tree searching for file extent items, without having
the whole fiemap target range locked in the inode's io tree - the
change introduced recently by commit b0ad381fa7 ("btrfs: fix
deadlock with fiemap and extent locking"). It only locks ranges in
the io tree when it finds a hole or prealloc extent since that
commit;
3) Note that fiemap clones each leaf before using it, and this is to
avoid deadlocks when locking a file range in the inode's io tree and
the fiemap buffer is memory mapped to some file, because writing
to the page with btrfs_page_mkwrite() will wait on any ordered extent
for the page's range and the ordered extent needs to lock the range
and may need to modify the same leaf, therefore leading to a deadlock
on the leaf;
4) While iterating the file extent items in the cloned leaf before
finding the hole in the range [64M, 65M[, the delalloc in that range
is flushed and its ordered extent completes - meaning the corresponding
file extent item is in the inode's subvolume tree, but not present in
the cloned leaf that fiemap is iterating over;
5) When fiemap finds the hole in the [64M, 65M[ range by seeing the gap in
the cloned leaf (or a file extent item with disk_bytenr == 0 in case
the NO_HOLES feature is not enabled), it will lock that file range in
the inode's io tree and then search for delalloc by checking for the
EXTENT_DELALLOC bit in the io tree for that range and ordered extents
(with btrfs_find_delalloc_in_range()). But it finds nothing since the
delalloc in that range was already flushed and the ordered extent
completed and is gone - as a result fiemap will not report that there's
delalloc or an extent for the range [64M, 65M[, so user space will be
mislead into thinking that there's a hole in that range.
This could actually be sporadically triggered with test case generic/094
from fstests, which reports a missing extent/delalloc range like this:
# generic/094 2s ... - output mismatch (see /home/fdmanana/git/hub/xfstests/results//generic/094.out.bad)
# --- tests/generic/094.out 2020-06-10 19:29:03.830519425 +0100
# +++ /home/fdmanana/git/hub/xfstests/results//generic/094.out.bad 2024-02-28 11:00:00.381071525 +0000
# @@ -1,3 +1,9 @@
# QA output created by 094
# fiemap run with sync
# fiemap run without sync
# +ERROR: couldn't find extent at 7
# +map is 'HHDDHPPDPHPH'
# +logical: [ 5.. 6] phys: 301517.. 301518 flags: 0x800 tot: 2
# +logical: [ 8.. 8] phys: 301520.. 301520 flags: 0x800 tot: 1
# ...
# (Run 'diff -u /home/fdmanana/git/hub/xfstests/tests/generic/094.out /home/fdmanana/git/hub/xfstests/results//generic/094.out.bad' to see the entire diff)
So in order to fix this, while still avoiding deadlocks in the case where
the fiemap buffer is memory mapped to the same file, change fiemap to work
like the following:
1) Always lock the whole range in the inode's io tree before starting to
iterate the inode's subvolume tree searching for file extent items,
just like we did before commit b0ad381fa7 ("btrfs: fix deadlock with
fiemap and extent locking");
2) Now instead of writing to the fiemap buffer every time we have an extent
to report, write instead to a temporary buffer (1 page), and when that
buffer becomes full, stop iterating the file extent items, unlock the
range in the io tree, release the search path, submit all the entries
kept in that buffer to the fiemap buffer, and then resume the search
for file extent items after locking again the remainder of the range in
the io tree.
The buffer having a size of a page, allows for 146 entries in a system
with 4K pages. This is a large enough value to have a good performance
by avoiding too many restarts of the search for file extent items.
In other words this preserves the huge performance gains made in the
last two years to fiemap, while avoiding the deadlocks in case the
fiemap buffer is memory mapped to the same file (useless in practice,
but possible and exercised by fuzz testing and syzbot).
Fixes: b0ad381fa7 ("btrfs: fix deadlock with fiemap and extent locking")
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 418b090277 ]
When FIEMAP_FLAG_SYNC is given to fiemap the expectation is that that
are no concurrent writes and we get a stable view of the inode's extent
layout.
When the flag is given we flush all IO (and wait for ordered extents to
complete) and then lock the inode in shared mode, however that leaves open
the possibility that a write might happen right after the flushing and
before locking the inode. So fix this by flushing again after locking the
inode - we leave the initial flushing before locking the inode to avoid
holding the lock and blocking other RO operations while waiting for IO
and ordered extents to complete. The second flushing while holding the
inode's lock will most of the time do nothing or very little since the
time window for new writes to have happened is small.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Stable-dep-of: 978b63f746 ("btrfs: fix race when detecting delalloc ranges during fiemap")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e91c23423 ]
Depending on the value of CONFIG_HZ, clang complains about a pointless
comparison:
drivers/md/dm-integrity.c:4085:12: error: result of comparison of
constant 42949672950 with expression of type
'unsigned int' is always false
[-Werror,-Wtautological-constant-out-of-range-compare]
if (val >= (uint64_t)UINT_MAX * 1000 / HZ) {
As the check remains useful for other configurations, shut up the
warning by adding a second type cast to uint64_t.
Fixes: 468dfca38b ("dm integrity: add a bitmap mode")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Justin Stitt <justinstitt@google.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 14128d6409 ]
Many of the IS_METEORLAKE conditions throughout the driver are supposed
to be checks for Xe_LPG and/or Xe_LPM+ IP, not for the MTL platform
specifically. Update those checks to ensure that the code will still
operate properly if/when these IP versions show up on future platforms.
v2:
- Update two more conditions (one for pg_enable, one for MTL HuC
compatibility).
v3:
- Don't change GuC/HuC compatibility check, which sounds like it truly
is specific to the MTL platform. (Gustavo)
- Drop a non-lineage workaround number for the OA timestamp frequency
workaround. (Gustavo)
Cc: Gustavo Sousa <gustavo.sousa@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230821180619.650007-20-matthew.d.roper@intel.com
Stable-dep-of: 186bce6827 ("drm/i915/mtl: Update workaround 14018575942")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a213086a0 ]
Several workarounds are guarded by IS_MTL_GRAPHICS_STEP. However none
of these workarounds are actually tied to MTL as a platform; they only
relate to the Xe_LPG graphics IP, regardless of what platform it appears
in. At the moment MTL is the only platform that uses Xe_LPG with IP
versions 12.70 and 12.71, but we can't count on this being true in the
future. Switch these to use a new IS_GFX_GT_IP_STEP() macro instead
that is purely based on IP version. IS_GFX_GT_IP_STEP() is also
GT-based rather than device-based, which will help prevent mistakes
where we accidentally try to apply Xe_LPG graphics workarounds to the
Xe_LPM+ media GT and vice-versa.
v2:
- Switch to a more generic and shorter IS_GT_IP_STEP macro that can be
used for both graphics and media IP (and any other kind of GTs that
show up in the future).
v3:
- Switch back to long-form IS_GFX_GT_IP_STEP macro. (Jani)
- Move macro to intel_gt.h. (Andi)
v4:
- Build IS_GFX_GT_IP_STEP on top of IS_GFX_GT_IP_RANGE and
IS_GRAPHICS_STEP building blocks and name the parameters from/until
rather than begin/fixed. (Jani)
- Fix usage examples in comment.
v5:
- Tweak comment on macro. (Gustavo)
Cc: Gustavo Sousa <gustavo.sousa@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Andi Shyti <andi.shyti@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230821180619.650007-15-matthew.d.roper@intel.com
Stable-dep-of: 186bce6827 ("drm/i915/mtl: Update workaround 14018575942")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f7696ded7c ]
Although some of our Xe_LPG workarounds were already being applied based
on IP version correctly, others were matching on MTL as a base platform,
which is incorrect. Although MTL is the only platform right now that
uses Xe_LPG IP, this may not always be the case. If a future platform
re-uses this graphics IP, the same workarounds should be applied, even
if it isn't a "MTL" platform.
We were also incorrectly applying Xe_LPG workarounds/tuning to the
Xe_LPM+ media IP in one or two places; we should make sure that we don't
try to apply graphics workarounds to the media GT and vice versa where
they don't belong. A new helper macro IS_GT_IP_RANGE() is added to help
ensure this is handled properly -- it checks that the GT matches the IP
type being tested as well as the IP version falling in the proper range.
Note that many of the stepping-based workarounds are still incorrectly
checking for a MTL base platform; that will be remedied in a later
patch.
v2:
- Rework macro into a slightly more generic IS_GT_IP_RANGE() that can
be used for either GFX or MEDIA checks.
v3:
- Switch back to separate macros for gfx and media. (Jani)
- Move macro to intel_gt.h. (Andi)
Cc: Gustavo Sousa <gustavo.sousa@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230821180619.650007-14-matthew.d.roper@intel.com
Stable-dep-of: 186bce6827 ("drm/i915/mtl: Update workaround 14018575942")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eaeb4b3614 ]
DG2 first production steppings were C0 (for DG2-G10), B1 (for DG2-G11),
and A1 (for DG2-G12). Several workarounds that apply onto to
pre-production hardware can be dropped. Furthermore, several
workarounds that apply to all production steppings can have their
conditions simplified to no longer check the GT stepping.
v2:
- Keep Wa_16011777198 in place for now; it will be removed separately
in a follow-up patch to keep review easier.
Bspec: 44477
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Matt Atwood <matthew.s.atwood@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230816214201.534095-10-matthew.d.roper@intel.com
Stable-dep-of: 186bce6827 ("drm/i915/mtl: Update workaround 14018575942")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 18685451fc ]
ip_local_out() and other functions can pass skb->sk as function argument.
If the skb is a fragment and reassembly happens before such function call
returns, the sk must not be released.
This affects skb fragments reassembled via netfilter or similar
modules, e.g. openvswitch or ct_act.c, when run as part of tx pipeline.
Eric Dumazet made an initial analysis of this bug. Quoting Eric:
Calling ip_defrag() in output path is also implying skb_orphan(),
which is buggy because output path relies on sk not disappearing.
A relevant old patch about the issue was :
8282f27449 ("inet: frag: Always orphan skbs inside ip_defrag()")
[..]
net/ipv4/ip_output.c depends on skb->sk being set, and probably to an
inet socket, not an arbitrary one.
If we orphan the packet in ipvlan, then downstream things like FQ
packet scheduler will not work properly.
We need to change ip_defrag() to only use skb_orphan() when really
needed, ie whenever frag_list is going to be used.
Eric suggested to stash sk in fragment queue and made an initial patch.
However there is a problem with this:
If skb is refragmented again right after, ip_do_fragment() will copy
head->sk to the new fragments, and sets up destructor to sock_wfree.
IOW, we have no choice but to fix up sk_wmem accouting to reflect the
fully reassembled skb, else wmem will underflow.
This change moves the orphan down into the core, to last possible moment.
As ip_defrag_offset is aliased with sk_buff->sk member, we must move the
offset into the FRAG_CB, else skb->sk gets clobbered.
This allows to delay the orphaning long enough to learn if the skb has
to be queued or if the skb is completing the reasm queue.
In the former case, things work as before, skb is orphaned. This is
safe because skb gets queued/stolen and won't continue past reasm engine.
In the latter case, we will steal the skb->sk reference, reattach it to
the head skb, and fix up wmem accouting when inet_frag inflates truesize.
Fixes: 7026b1ddb6 ("netfilter: Pass socket pointer down through okfn().")
Diagnosed-by: Eric Dumazet <edumazet@google.com>
Reported-by: xingwei lee <xrivendell7@gmail.com>
Reported-by: yue sun <samsun1006219@gmail.com>
Reported-by: syzbot+e5167d7144a62715044c@syzkaller.appspotmail.com
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240326101845.30836-1-fw@strlen.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 40d4b4807c ]
The Octeontx2 MAC block (CGX) has separate data paths (SMU and GMP) for
different speeds, allowing for efficient data transfer.
The previous patch which added pause frame configuration has a bug due
to which pause frame feature is not working in GMP mode.
This patch fixes the issue by configurating appropriate registers.
Fixes: f7e086e754 ("octeontx2-af: Pause frame configuration at cgx")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240326052720.4441-1-hkelam@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dfd222e2ae ]
The unimac requires the PHY RX clk during reset or it may be put
into a bad state. Bring up the unimac after link up to ensure the
PHY RX clk exists.
Fixes: 490cb41200 ("net: bcmasp: Add support for ASP2.0 Ethernet controller")
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 216e7bf740 ]
Skip hook unregistration when adding or deleting devices from an
existing netdev basechain. Otherwise, commit/abort path try to
unregister hooks which not enabled.
Fixes: b9703ed44f ("netfilter: nf_tables: support for adding new devices to an existing netdev chain")
Fixes: 7d937b1071 ("netfilter: nf_tables: support for deleting devices in an existing netdev chain")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e1fb6f00f ]
netdev basechain updates are stored in the transaction object hook list.
When setting on the table dormant flag, it iterates over the existing
hooks in the basechain. Thus, skipping the hooks that are being
added/deleted in this transaction, which leaves hook registration in
inconsistent state.
Reject table flag updates in combination with netdev basechain updates
in the same batch:
- Update table flags and add/delete basechain: Check from basechain update
path if there are pending flag updates for this table.
- add/delete basechain and update table flags: Iterate over the transaction
list to search for basechain updates from the table update path.
In both cases, the batch is rejected. Based on suggestion from Florian Westphal.
Fixes: b9703ed44f ("netfilter: nf_tables: support for adding new devices to an existing netdev chain")
Fixes: 7d937b1071 ("netfilter: nf_tables: support for deleting devices in an existing netdev chain")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b32ca27fa2 ]
Report EOPNOTSUPP if NFT_MSG_DESTROYCHAIN is used to delete hooks in an
existing netdev basechain, thus, only NFT_MSG_DELCHAIN is allowed.
Fixes: 7d937b1071 ("netfilter: nf_tables: support for deleting devices in an existing netdev chain")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8876a37277 ]
fscache emits a lot of duplicate cookie warnings with cifs because the
index key for the fscache cookies does not include everything that the
cifs_find_inode() function does. The latter is used with iget5_locked() to
distinguish between inodes in the local inode cache.
Fix this by adding the creation time and file type to the fscache cookie
key.
Additionally, add a couple of comments to note that if one is changed the
other must be also.
Signed-off-by: David Howells <dhowells@redhat.com>
Fixes: 70431bfd82 ("cifs: Support fscache indexing rewrite")
cc: Shyam Prasad N <nspmangalore@gmail.com>
cc: Rohith Surabattula <rohiths.msft@gmail.com>
cc: Jeff Layton <jlayton@kernel.org>
cc: linux-cifs@vger.kernel.org
cc: netfs@lists.linux.dev
cc: linux-fsdevel@vger.kernel.org
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 85eef9a41d ]
process_rx_list may not copy as many bytes as we want to the userspace
buffer, for example in case we hit an EFAULT during the copy. If this
happens, we should only count the bytes that were actually copied,
which may be 0.
Subtracting async_copy_bytes is correct in both peek and !peek cases,
because decrypted == async_copy_bytes + peeked for the peek case: peek
is always !ZC, and we can go through either the sync or async path. In
the async case, we add chunk to both decrypted and
async_copy_bytes. In the sync case, we add chunk to both decrypted and
peeked. I missed that in commit 6caaf10442 ("tls: fix peeking with
sync+async decryption").
Fixes: 4d42cd6bc2 ("tls: rx: fix return value for async crypto")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/1b5a1eaab3c088a9dd5d9f1059ceecd7afe888d1.1711120964.git.sd@queasysnail.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5bd088d6c2 ]
Currently, loopback test may be skipped when resetting, but the test
result will still show as 'PASS', because the driver doesn't set
ETH_TEST_FL_FAILED flag. Fix it by setting the flag and
initializating the value to UNEXECUTED.
Fixes: 4c8dab1c70 ("net: hns3: reconstruct function hns3_self_test")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 93305b77ff ]
The devlink reload process will access the hardware resources,
but the register operation is done before the hardware is initialized.
So, processing the devlink reload during initialization may lead to kernel
crash. This patch fixes this by taking devl_lock during initialization.
Fixes: b741269b27 ("net: hns3: add support for registering devlink for PF")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 40e2710860 ]
ACPICA commit 9061cd9aa131205657c811a52a9f8325a040c6c9
Errors in acpi_evaluate_object() can lead to incorrect state of buffer.
This can lead to access to data in previously ACPI_FREEd buffer and
secondary ACPI_FREE to the same buffer later.
Handle errors in acpi_evaluate_object the same way it is done earlier
with acpi_ns_handle_to_pathname.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Link: https://github.com/acpica/acpica/commit/9061cd9a
Fixes: 5fd033288a ("ACPICA: debugger: add command to dump all fields of particular subtype")
Signed-off-by: Nikita Kiryushin <kiryushin@ancud.ru>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f1425529c3 ]
Locally generated IP multicast packets (such as the ones used in the
test) do not perform routing and simply egress the bound device.
However, as explained in commit 8bcfb4ae4d ("selftests: forwarding:
Fix failing tests with old libnet"), old versions of libnet (used by
mausezahn) do not use the "SO_BINDTODEVICE" socket option. Specifically,
the library started using the option for IPv6 sockets in version 1.1.6
and for IPv4 sockets in version 1.2. This explains why on Ubuntu - which
uses version 1.1.6 - the IPv4 overlay tests are failing whereas the IPv6
ones are passing.
Fix by specifying the source and destination MAC of the packets which
will cause mausezahn to use a packet socket instead of an IP socket.
Fixes: 62199e3f16 ("selftests: net: Add VXLAN MDB test")
Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Closes: https://lore.kernel.org/netdev/5bb50349-196d-4892-8ed2-f37543aa863f@alu.unizg.hr/
Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/20240325075030.2379513-1-idosch@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 151c9c724d ]
We had various syzbot reports about tcp timers firing after
the corresponding netns has been dismantled.
Fortunately Josef Bacik could trigger the issue more often,
and could test a patch I wrote two years ago.
When TCP sockets are closed, we call inet_csk_clear_xmit_timers()
to 'stop' the timers.
inet_csk_clear_xmit_timers() can be called from any context,
including when socket lock is held.
This is the reason it uses sk_stop_timer(), aka del_timer().
This means that ongoing timers might finish much later.
For user sockets, this is fine because each running timer
holds a reference on the socket, and the user socket holds
a reference on the netns.
For kernel sockets, we risk that the netns is freed before
timer can complete, because kernel sockets do not hold
reference on the netns.
This patch adds inet_csk_clear_xmit_timers_sync() function
that using sk_stop_timer_sync() to make sure all timers
are terminated before the kernel socket is released.
Modules using kernel sockets close them in their netns exit()
handler.
Also add sock_not_owned_by_me() helper to get LOCKDEP
support : inet_csk_clear_xmit_timers_sync() must not be called
while socket lock is held.
It is very possible we can revert in the future commit
3a58f13a88 ("net: rds: acquire refcount on TCP sockets")
which attempted to solve the issue in rds only.
(net/smc/af_smc.c and net/mptcp/subflow.c have similar code)
We probably can remove the check_net() tests from
tcp_out_of_resources() and __tcp_close() in the future.
Reported-by: Josef Bacik <josef@toxicpanda.com>
Closes: https://lore.kernel.org/netdev/20240314210740.GA2823176@perftesting/
Fixes: 26abe14379 ("net: Modify sk_alloc to not reference count the netns of kernel sockets.")
Fixes: 8a68173691 ("net: sk_clone_lock() should only do get_net() if the parent is not a kernel socket")
Link: https://lore.kernel.org/bpf/CANn89i+484ffqb93aQm1N-tjxxvb3WDKX0EbD7318RwRgsatjw@mail.gmail.com/
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Josef Bacik <josef@toxicpanda.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Link: https://lore.kernel.org/r/20240322135732.1535772-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b11c81731c ]
commit e748d0fd66 ("net: hsr: Disable promiscuous mode in
offload mode") disables promiscuous mode of slave devices
while creating an HSR interface. But while deleting the
HSR interface, it does not take care of it. It decreases the
promiscuous mode count, which eventually enables promiscuous
mode on the slave devices when creating HSR interface again.
Fix this by not decrementing the promiscuous mode count while
deleting the HSR interface when offload is enabled.
Fixes: e748d0fd66 ("net: hsr: Disable promiscuous mode in offload mode")
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20240322100447.27615-1-r-gunasekaran@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit afb373ff3f ]
The IO subsystem expects a driver to retry a ccw_device_start, when the
subsequent interrupt response block (irb) contains a deferred
condition code 1.
Symptoms before this commit:
On the read channel we always trigger the next read anyhow, so no
different behaviour here.
On the write channel we may experience timeout errors, because the
expected reply will never be received without the retry.
Other callers of qeth_send_control_data() may wrongly assume that the ccw
was successful, which may cause problems later.
Note that since
commit 2297791c92 ("s390/cio: dont unregister subchannel from child-drivers")
and
commit 5ef1dc40ff ("s390/cio: fix invalid -EBUSY on ccw_device_start")
deferred CC1s are much more likely to occur. See the commit message of the
latter for more background information.
Fixes: 2297791c92 ("s390/cio: dont unregister subchannel from child-drivers")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Co-developed-by: Thorsten Winkler <twinkler@linux.ibm.com>
Signed-off-by: Thorsten Winkler <twinkler@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Link: https://lore.kernel.org/r/20240321115337.3564694-1-wintera@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 47ce2956c7 ]
The initial igc Tx timestamping implementation used only one register for
retrieving Tx timestamps. Commit 3ed247e789 ("igc: Add support for
multiple in-flight TX timestamps") added support for utilizing all four of
them e.g., for multiple domain support. Remove the stale comment/FIXME.
Fixes: 3ed247e789 ("igc: Add support for multiple in-flight TX timestamps")
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aec806fb4a ]
Change kzalloc() flags used in ixgbe_ipsec_vf_add_sa() to GFP_ATOMIC, to
avoid sleeping in IRQ context.
Dan Carpenter, with the help of Smatch, has found following issue:
The patch eda0333ac2: "ixgbe: add VF IPsec management" from Aug 13,
2018 (linux-next), leads to the following Smatch static checker
warning: drivers/net/ethernet/intel/ixgbe/ixgbe_ipsec.c:917 ixgbe_ipsec_vf_add_sa()
warn: sleeping in IRQ context
The call tree that Smatch is worried about is:
ixgbe_msix_other() <- IRQ handler
-> ixgbe_msg_task()
-> ixgbe_rcv_msg_from_vf()
-> ixgbe_ipsec_vf_add_sa()
Fixes: eda0333ac2 ("ixgbe: add VF IPsec management")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/intel-wired-lan/db31a0b0-4d9f-4e6b-aed8-88266eb5665c@moroto.mountain
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1cb7fdb1df ]
The ice driver would previously panic after suspend. This is caused
from the driver *only* calling the ice_vsi_free_q_vectors() function by
itself, when it is suspending. Since commit b3e7b3a6ee ("ice: prevent
NULL pointer deref during reload") the driver has zeroed out
num_q_vectors, and only restored it in ice_vsi_cfg_def().
This further causes the ice_rebuild() function to allocate a zero length
buffer, after which num_q_vectors is updated, and then the new value of
num_q_vectors is used to index into the zero length buffer, which
corrupts memory.
The fix entails making sure all the code referencing num_q_vectors only
does so after it has been reset via ice_vsi_cfg_def().
I didn't perform a full bisect, but I was able to test against 6.1.77
kernel and that ice driver works fine for suspend/resume with no panic,
so sometime since then, this problem was introduced.
Also clean up an un-needed init of a local variable in the function
being modified.
PANIC from 6.8.0-rc1:
[1026674.915596] PM: suspend exit
[1026675.664697] ice 0000:17:00.1: PTP reset successful
[1026675.664707] ice 0000:17:00.1: 2755 msecs passed between update to cached PHC time
[1026675.667660] ice 0000:b1:00.0: PTP reset successful
[1026675.675944] ice 0000:b1:00.0: 2832 msecs passed between update to cached PHC time
[1026677.137733] ixgbe 0000:31:00.0 ens787: NIC Link is Up 1 Gbps, Flow Control: None
[1026677.190201] BUG: kernel NULL pointer dereference, address: 0000000000000010
[1026677.192753] ice 0000:17:00.0: PTP reset successful
[1026677.192764] ice 0000:17:00.0: 4548 msecs passed between update to cached PHC time
[1026677.197928] #PF: supervisor read access in kernel mode
[1026677.197933] #PF: error_code(0x0000) - not-present page
[1026677.197937] PGD 1557a7067 P4D 0
[1026677.212133] ice 0000:b1:00.1: PTP reset successful
[1026677.212143] ice 0000:b1:00.1: 4344 msecs passed between update to cached PHC time
[1026677.212575]
[1026677.243142] Oops: 0000 [#1] PREEMPT SMP NOPTI
[1026677.247918] CPU: 23 PID: 42790 Comm: kworker/23:0 Kdump: loaded Tainted: G W 6.8.0-rc1+ #1
[1026677.257989] Hardware name: Intel Corporation M50CYP2SBSTD/M50CYP2SBSTD, BIOS SE5C620.86B.01.01.0005.2202160810 02/16/2022
[1026677.269367] Workqueue: ice ice_service_task [ice]
[1026677.274592] RIP: 0010:ice_vsi_rebuild_set_coalesce+0x130/0x1e0 [ice]
[1026677.281421] Code: 0f 84 3a ff ff ff 41 0f b7 74 ec 02 66 89 b0 22 02 00 00 81 e6 ff 1f 00 00 e8 ec fd ff ff e9 35 ff ff ff 48 8b 43 30 49 63 ed <41> 0f b7 34 24 41 83 c5 01 48 8b 3c e8 66 89 b7 aa 02 00 00 81 e6
[1026677.300877] RSP: 0018:ff3be62a6399bcc0 EFLAGS: 00010202
[1026677.306556] RAX: ff28691e28980828 RBX: ff28691e41099828 RCX: 0000000000188000
[1026677.314148] RDX: 0000000000000000 RSI: 0000000000000010 RDI: ff28691e41099828
[1026677.321730] RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000
[1026677.329311] R10: 0000000000000007 R11: ffffffffffffffc0 R12: 0000000000000010
[1026677.336896] R13: 0000000000000000 R14: 0000000000000000 R15: ff28691e0eaa81a0
[1026677.344472] FS: 0000000000000000(0000) GS:ff28693cbffc0000(0000) knlGS:0000000000000000
[1026677.353000] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[1026677.359195] CR2: 0000000000000010 CR3: 0000000128df4001 CR4: 0000000000771ef0
[1026677.366779] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[1026677.374369] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[1026677.381952] PKRU: 55555554
[1026677.385116] Call Trace:
[1026677.388023] <TASK>
[1026677.390589] ? __die+0x20/0x70
[1026677.394105] ? page_fault_oops+0x82/0x160
[1026677.398576] ? do_user_addr_fault+0x65/0x6a0
[1026677.403307] ? exc_page_fault+0x6a/0x150
[1026677.407694] ? asm_exc_page_fault+0x22/0x30
[1026677.412349] ? ice_vsi_rebuild_set_coalesce+0x130/0x1e0 [ice]
[1026677.418614] ice_vsi_rebuild+0x34b/0x3c0 [ice]
[1026677.423583] ice_vsi_rebuild_by_type+0x76/0x180 [ice]
[1026677.429147] ice_rebuild+0x18b/0x520 [ice]
[1026677.433746] ? delay_tsc+0x8f/0xc0
[1026677.437630] ice_do_reset+0xa3/0x190 [ice]
[1026677.442231] ice_service_task+0x26/0x440 [ice]
[1026677.447180] process_one_work+0x174/0x340
[1026677.451669] worker_thread+0x27e/0x390
[1026677.455890] ? __pfx_worker_thread+0x10/0x10
[1026677.460627] kthread+0xee/0x120
[1026677.464235] ? __pfx_kthread+0x10/0x10
[1026677.468445] ret_from_fork+0x2d/0x50
[1026677.472476] ? __pfx_kthread+0x10/0x10
[1026677.476671] ret_from_fork_asm+0x1b/0x30
[1026677.481050] </TASK>
Fixes: b3e7b3a6ee ("ice: prevent NULL pointer deref during reload")
Reported-by: Robert Elliott <elliott@hpe.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5995ef88e3 ]
Previously only case when queues amount is lower was covered. Implement
realloc for case when queues amount is higher than previous one. Use
krealloc() function and zero new allocated elements.
It has to be done before ice_vsi_def_cfg(), because stats element for
ring is set there.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Stable-dep-of: 1cb7fdb1df ("ice: fix memory corruption bug with suspend and rebuild")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 817b18965b ]
According to the datasheet, the recipe association data is an 8-byte
little-endian value. It is described as 'Bitmap of the recipe indexes
associated with this profile', it is from 24 to 31 byte area in FW.
Therefore, it is defined to '__le64 recipe_assoc' in struct
ice_aqc_recipe_to_profile. And then fix the bitmap casting issue, as we
must never ever use castings for bitmap type.
Fixes: 1e0f9881ef ("ice: Flesh out implementation of support for SRIOV on bonded interface")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Andrii Staikov <andrii.staikov@intel.com>
Reviewed-by: Jan Sokolowski <jan.sokolowski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Steven Zou <steven.zou@intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 29fa9a984b ]
Multi rx queue allows to spread the load of the Rx streams on different
CPUs. 9000 series required complex synchronization mechanisms from the
driver side since the hardware / firmware is not able to provide
information about duplicate packets and timeouts inside the reordering
buffer.
Users have complained that for newer devices, all those synchronization
mechanisms have caused spurious packet drops. Those packet drops
disappeared if we simplify the code, but unfortunately, we can't have
RSS enabled on 9000 series without this complex code.
Remove support for RSS on 9000 so that we can make the code much simpler
for newer devices and fix the bugs for them.
The down side of this patch is a that all the Rx path will be routed to
a single CPU, but this has never been an issue, the modern CPUs are just
fast enough to cope with all the traffic.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231017115047.2917eb8b7af9.Iddd7dcf335387ba46fcbbb6067ef4ff9cd3755a7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Stable-dep-of: e78d787730 ("wifi: iwlwifi: mvm: include link ID when releasing frames")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d6c30c5a16 ]
The mlxbf_gige_open() routine starts the PHY as part of normal
initialization. The mlxbf_gige_open() routine must stop the
PHY during its error paths.
Fixes: f92e1869d7 ("Add Mellanox BlueField Gigabit Ethernet driver")
Signed-off-by: David Thompson <davthompson@nvidia.com>
Reviewed-by: Asmaa Mnebhi <asmaa@nvidia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 114b5b3b4b ]
A64_LDRSW() takes three registers: Xt, Xn, Xm as arguments and it loads
and sign extends the value at address Xn + Xm into register Xt.
Currently, the offset is being directly used in place of the tmp
register which has the offset already loaded by the last emitted
instruction.
This will cause JIT failures. The easiest way to reproduce this is to
test the following code through test_bpf module:
{
"BPF_LDX_MEMSX | BPF_W",
.u.insns_int = {
BPF_LD_IMM64(R1, 0x00000000deadbeefULL),
BPF_LD_IMM64(R2, 0xffffffffdeadbeefULL),
BPF_STX_MEM(BPF_DW, R10, R1, -7),
BPF_LDX_MEMSX(BPF_W, R0, R10, -7),
BPF_JMP_REG(BPF_JNE, R0, R2, 1),
BPF_ALU64_IMM(BPF_MOV, R0, 0),
BPF_EXIT_INSN(),
},
INTERNAL,
{ },
{ { 0, 0 } },
.stack_depth = 7,
},
We need to use the offset as -7 to trigger this code path, there could
be other valid ways to trigger this from proper BPF programs as well.
This code is rejected by the JIT because -7 is passed to A64_LDRSW() but
it expects a valid register (0 - 31).
roott@pjy:~# modprobe test_bpf test_name="BPF_LDX_MEMSX | BPF_W"
[11300.490371] test_bpf: test_bpf: set 'test_bpf' as the default test_suite.
[11300.491750] test_bpf: #345 BPF_LDX_MEMSX | BPF_W
[11300.493179] aarch64_insn_encode_register: unknown register encoding -7
[11300.494133] aarch64_insn_encode_register: unknown register encoding -7
[11300.495292] FAIL to select_runtime err=-524
[11300.496804] test_bpf: Summary: 0 PASSED, 1 FAILED, [0/0 JIT'ed]
modprobe: ERROR: could not insert 'test_bpf': Invalid argument
Applying this patch fixes the issue.
root@pjy:~# modprobe test_bpf test_name="BPF_LDX_MEMSX | BPF_W"
[ 292.837436] test_bpf: test_bpf: set 'test_bpf' as the default test_suite.
[ 292.839416] test_bpf: #345 BPF_LDX_MEMSX | BPF_W jited:1 156 PASS
[ 292.844794] test_bpf: Summary: 1 PASSED, 0 FAILED, [1/1 JIT'ed]
Fixes: cc88f540da ("bpf, arm64: Support sign-extension load instructions")
Signed-off-by: Puranjay Mohan <puranjay12@gmail.com>
Message-ID: <20240312235917.103626-1-puranjay12@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ded842b35 ]
Kui-Feng Lee reported a crash on s390x triggered by the
dummy_st_ops/dummy_init_ptr_arg test [1]:
[<0000000000000002>] 0x2
[<00000000009d5cde>] bpf_struct_ops_test_run+0x156/0x250
[<000000000033145a>] __sys_bpf+0xa1a/0xd00
[<00000000003319dc>] __s390x_sys_bpf+0x44/0x50
[<0000000000c4382c>] __do_syscall+0x244/0x300
[<0000000000c59a40>] system_call+0x70/0x98
This is caused by GCC moving memcpy() after assignments in
bpf_jit_plt(), resulting in NULL pointers being written instead of
the return and the target addresses.
Looking at the GCC internals, the reordering is allowed because the
alias analysis thinks that the memcpy() destination and the assignments'
left-hand-sides are based on different objects: new_plt and
bpf_plt_ret/bpf_plt_target respectively, and therefore they cannot
alias.
This is in turn due to a violation of the C standard:
When two pointers are subtracted, both shall point to elements of the
same array object, or one past the last element of the array object
...
From the C's perspective, bpf_plt_ret and bpf_plt are distinct objects
and cannot be subtracted. In the practical terms, doing so confuses the
GCC's alias analysis.
The code was written this way in order to let the C side know a few
offsets defined in the assembly. While nice, this is by no means
necessary. Fix the noncompliance by hardcoding these offsets.
[1] https://lore.kernel.org/bpf/c9923c1d-971d-4022-8dc8-1364e929d34c@gmail.com/
Fixes: f1d5df84cd ("s390/bpf: Implement bpf_arch_text_poke()")
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Message-ID: <20240320015515.11883-1-iii@linux.ibm.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5384cc0d1a ]
When getting kernel version via make, the result may be polluted by other
output, like directory change info. e.g.
$ export MAKEFLAGS="-w"
$ make kernelversion
make: Entering directory '/home/net'
6.8.0
make: Leaving directory '/home/net'
This will distort the reStructuredText output and make latter rst2man
failed like:
[...]
bpf-helpers.rst:20: (WARNING/2) Field list ends without a blank line; unexpected unindent.
[...]
Using silent mode would help. e.g.
$ make -s --no-print-directory kernelversion
6.8.0
Fixes: fd0a38f9c3 ("scripts/bpf: Set version attribute for bpf-helpers(7) man page")
Signed-off-by: Michael Hofmann <mhofmann@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Quentin Monnet <qmo@kernel.org>
Acked-by: Alejandro Colomar <alx@kernel.org>
Link: https://lore.kernel.org/bpf/20240315023443.2364442-1-liuhangbin@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Enhanced Strobe and clock gating are set in the SDHCI_VENDOR register,
so make the driver aware it needs to do this for this controller.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Samsung EVO Plus, Pro Plus and Evo Ultimate cards of this era appear to
have a broken cache-flush implementation when operating in CQ mode.
Unfortunately the cards seem to use a separate CID name string for every
variant and capacity, so nobble the cache feature for this MANFID, OEMID
and year. Turning this off seems to have negligible impact on
random-write throughput in non-CQ mode.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Applying MMC_QUIRK_BROKEN_SD_CACHE is broken, as the card's extended
registers are parsed prior to the quirk being applied in mmc_blk.
Split this out into an SD-specific list of quirks and apply in
mmc_sd_init_card instead.
Fixes: c467c8f081 ("mmc: Add MMC_QUIRK_BROKEN_SD_CACHE for Kingston Canvas Go Plus from 11/2019")
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Commit 7d239fbf9d broke 802.1X authentication by setting
profile->use_fwsup = NONE whenever PSK is not used. However
802.1X does not use PSK and requires profile->use_fwsup set
to 1X, or brcmf_cfg80211_set_pmk() fails. Fix this by checking
that profile->use_fwsup is not already set to 1X and avoid
setting it to NONE in that case.
Fixes: 7d239fbf9d (brcmfmac: Fix interoperating DPP and other encryption network access)
Fixes: https://github.com/raspberrypi/linux/issues/5964
1. If firmware supports 4-way handshake offload but not supports DPP
4-way offload, when user first connects encryption network, driver will
set "sup_wpa 1" to firmware, but it will further result in DPP
connection failure since firmware won't send EAPOL frame to host.
2. Fix DPP AP mode handling action frames.
3. For some firmware without fwsup support, the join procedure will be
skipped due to "sup_wpa" iovar returning not-support. Check the fwsup
feature before do such iovar.
Signed-off-by: Kurt Lee <kurt.lee@cypress.com>
Signed-off-by: Double Lo <double.lo@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
This supports reading and writing OTP using the firmware
mailbox interface.
It needs supporting firmware to run.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
When setting the interrupt type, it is unlikely that any latched events
are of interest, so clear them.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Support the use of the brcm,pins property for GPIOs in banks 1 and 2,
but only for inputs and outputs - no other legacy mapping.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
commit 0f4a1e8098 upstream.
SEV-SNP requires encrypted memory to be validated before access.
Because the ROM memory range is not part of the e820 table, it is not
pre-validated by the BIOS. Therefore, if a SEV-SNP guest kernel wishes
to access this range, the guest must first validate the range.
The current SEV-SNP code does indeed scan the ROM range during early
boot and thus attempts to validate the ROM range in probe_roms().
However, this behavior is neither sufficient nor necessary for the
following reasons:
* With regards to sufficiency, if EFI_CONFIG_TABLES are not enabled and
CONFIG_DMI_SCAN_MACHINE_NON_EFI_FALLBACK is set, the kernel will
attempt to access the memory at SMBIOS_ENTRY_POINT_SCAN_START (which
falls in the ROM range) prior to validation.
For example, Project Oak Stage 0 provides a minimal guest firmware
that currently meets these configuration conditions, meaning guests
booting atop Oak Stage 0 firmware encounter a problematic call chain
during dmi_setup() -> dmi_scan_machine() that results in a crash
during boot if SEV-SNP is enabled.
* With regards to necessity, SEV-SNP guests generally read garbage
(which changes across boots) from the ROM range, meaning these scans
are unnecessary. The guest reads garbage because the legacy ROM range
is unencrypted data but is accessed via an encrypted PMD during early
boot (where the PMD is marked as encrypted due to potentially mapping
actually-encrypted data in other PMD-contained ranges).
In one exceptional case, EISA probing treats the ROM range as
unencrypted data, which is inconsistent with other probing.
Continuing to allow SEV-SNP guests to use garbage and to inconsistently
classify ROM range encryption status can trigger undesirable behavior.
For instance, if garbage bytes appear to be a valid signature, memory
may be unnecessarily reserved for the ROM range. Future code or other
use cases may result in more problematic (arbitrary) behavior that
should be avoided.
While one solution would be to overhaul the early PMD mapping to always
treat the ROM region of the PMD as unencrypted, SEV-SNP guests do not
currently rely on data from the ROM region during early boot (and even
if they did, they would be mostly relying on garbage data anyways).
As a simpler solution, skip the ROM range scans (and the otherwise-
necessary range validation) during SEV-SNP guest early boot. The
potential SEV-SNP guest crash due to lack of ROM range validation is
thus avoided by simply not accessing the ROM range.
In most cases, skip the scans by overriding problematic x86_init
functions during sme_early_init() to SNP-safe variants, which can be
likened to x86_init overrides done for other platforms (ex: Xen); such
overrides also avoid the spread of cc_platform_has() checks throughout
the tree.
In the exceptional EISA case, still use cc_platform_has() for the
simplest change, given (1) checks for guest type (ex: Xen domain status)
are already performed here, and (2) these checks occur in a subsys
initcall instead of an x86_init function.
[ bp: Massage commit message, remove "we"s. ]
Fixes: 9704c07bf9 ("x86/kernel: Validate ROM memory before accessing when SEV-SNP is active")
Signed-off-by: Kevin Loughlin <kevinloughlin@google.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Cc: <stable@kernel.org>
Link: https://lore.kernel.org/r/20240313121546.2964854-1-kevinloughlin@google.com
Signed-off-by: Kevin Loughlin <kevinloughlin@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e68a458bc upstream.
As of commit d8649fc1c5 ("scsi: libsas: Do discovery on empty PHY to
update PHY info"), do discovery will send a new SMP_DISCOVER and update
phy->phy_change_count. We found that if the disk is reconnected and phy
change_count changes at this time, the disk scanning process will not be
triggered.
Therefore, call sas_set_ex_phy() to update the PHY info with the results of
the last query. And because the previous phy info will be used when calling
sas_unregister_devs_sas_addr(), sas_unregister_devs_sas_addr() should be
called before sas_set_ex_phy().
Fixes: d8649fc1c5 ("scsi: libsas: Do discovery on empty PHY to update PHY info")
Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Link: https://lore.kernel.org/r/20240307141413.48049-3-yangxingui@huawei.com
Reviewed-by: John Garry <john.g.garry@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 532a0c57d7 upstream.
This was reverts commit 8009479ee9.
It was originally in x86/urgent, but was deemed wrong so got zapped.
But in the meantime, x86/urgent had been merged into x86/apic to
resolve a conflict. I didn't notice the merge so didn't zap it
from x86/apic and it managed to make it up with the x86/apic
material.
The reverted commit is known to cause some KASAN problems.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6aaceb7d9c upstream.
Some DELL systems don't like UCSI_ACK_CC_CI commands with the
UCSI_ACK_CONNECTOR_CHANGE but not the UCSI_ACK_COMMAND_COMPLETE
bit set. The current quirk still leaves room for races because
it requires two consecutive ACK commands to be sent.
Refactor and significantly simplify the quirk to fix this:
Send a dummy command and bundle the connector change ack with the
command completion ack in a single UCSI_ACK_CC_CI command.
This removes the need to probe for the quirk.
While there define flag bits for struct ucsi_acpi->flags in ucsi_acpi.c
and don't re-use definitions from ucsi.h for struct ucsi->flags.
Fixes: f3be347ea4 ("usb: ucsi_acpi: Quirk to ack a connector change ack cmd")
Cc: stable@vger.kernel.org
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Link: https://lore.kernel.org/r/20240320073927.1641788-5-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 15b2e71b46 upstream.
Suppose we sleep on the PPM lock after clearing the EVENT_PENDING
bit because the thread for another connector is executing a command.
In this case the command completion of the other command will still
report the connector change for our connector.
Clear the EVENT_PENDING bit under the PPM lock to avoid another
useless call to ucsi_handle_connector_change() in this case.
Fixes: c9aed03a0a ("usb: ucsi: Add missing ppm_lock")
Cc: stable <stable@kernel.org>
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Link: https://lore.kernel.org/r/20240320073927.1641788-2-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a587a0352 upstream.
It is possible trigger below warning message from mass storage function,
WARNING: CPU: 6 PID: 3839 at drivers/usb/gadget/udc/core.c:294 usb_ep_queue+0x7c/0x104
pc : usb_ep_queue+0x7c/0x104
lr : fsg_main_thread+0x494/0x1b3c
Root cause is mass storage function try to queue request from main thread,
but other thread may already disable ep when function disable.
As there is no function failure in the driver, in order to avoid effort
to fix warning, change WARN_ON_ONCE() in usb_ep_queue() to pr_debug().
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
Signed-off-by: yuan linyu <yuanlinyu@hihonor.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240315020144.2715575-1-yuanlinyu@hihonor.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f4d1960764 upstream.
The show and store callback routines for the "disable" sysfs attribute
file in port.c acquire the device lock for the port's parent hub
device. This can cause problems if another process has locked the hub
to remove it or change its configuration:
Removing the hub or changing its configuration requires the
hub interface to be removed, which requires the port device
to be removed, and device_del() waits until all outstanding
sysfs attribute callbacks for the ports have returned. The
lock can't be released until then.
But the disable_show() or disable_store() routine can't return
until after it has acquired the lock.
The resulting deadlock can be avoided by calling
sysfs_break_active_protection(). This will cause the sysfs core not
to wait for the attribute's callback routine to return, allowing the
removal to proceed. The disadvantage is that after making this call,
there is no guarantee that the hub structure won't be deallocated at
any moment. To prevent this, we have to acquire a reference to it
first by calling hub_get().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/f7a8c135-a495-4ce6-bd49-405a45e7ea9a@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 80ba43e9f7 upstream.
Among the attribute file callback routines in
drivers/usb/core/sysfs.c, the interface_authorized_store() function is
the only one which acquires a device lock on an ancestor device: It
calls usb_deauthorize_interface(), which locks the interface's parent
USB device.
The will lead to deadlock if another process already owns that lock
and tries to remove the interface, whether through a configuration
change or because the device has been disconnected. As part of the
removal procedure, device_del() waits for all ongoing sysfs attribute
callbacks to complete. But usb_deauthorize_interface() can't complete
until the device lock has been released, and the lock won't be
released until the removal has finished.
The mechanism provided by sysfs to prevent this kind of deadlock is
to use the sysfs_break_active_protection() function, which tells sysfs
not to wait for the attribute callback.
Reported-and-tested by: Yue Sun <samsun1006219@gmail.com>
Reported by: xingwei lee <xrivendell7@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/linux-usb/CAEkJfYO6jRVC8Tfrd_R=cjO0hguhrV31fDPrLrNOOHocDkPoAA@mail.gmail.com/#r
Fixes: 310d2b4124 ("usb: interface authorization: SysFS part of USB interface authorization")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1c37eea1-9f56-4534-b9d8-b443438dc869@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef25725b7f upstream.
gcc-14 warns about this strncpy() that results in a non-terminated
string for an overflow:
In file included from include/linux/string.h:369,
from drivers/staging/vc04_services/vchiq-mmal/mmal-vchiq.c:20:
In function 'strncpy',
inlined from 'create_component' at drivers/staging/vc04_services/vchiq-mmal/mmal-vchiq.c:940:2:
include/linux/fortify-string.h:108:33: error: '__builtin_strncpy' specified bound 128 equals destination size [-Werror=stringop-truncation]
Change it to strscpy_pad(), which produces a properly terminated and
zero-padded string.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/20240313163712.224585-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f23a4d6e07 upstream.
Commit fc663711b9 ("scsi: core: Remove the /proc/scsi/${proc_name}
directory earlier") fixed a bug related to modules loading/unloading, by
adding a call to scsi_proc_hostdir_rm() on scsi_remove_host(). But that led
to a potential duplicate call to the hostdir_rm() routine, since it's also
called from scsi_host_dev_release(). That triggered a regression report,
which was then fixed by commit be03df3d4b ("scsi: core: Fix a procfs host
directory removal regression"). The fix just dropped the hostdir_rm() call
from dev_release().
But it happens that this proc directory is created on scsi_host_alloc(),
and that function "pairs" with scsi_host_dev_release(), while
scsi_remove_host() pairs with scsi_add_host(). In other words, it seems the
reason for removing the proc directory on dev_release() was meant to cover
cases in which a SCSI host structure was allocated, but the call to
scsi_add_host() didn't happen. And that pattern happens to exist in some
error paths, for example.
Syzkaller causes that by using USB raw gadget device, error'ing on
usb-storage driver, at usb_stor_probe2(). By checking that path, we can see
that the BadDevice label leads to a scsi_host_put() after a SCSI host
allocation, but there's no call to scsi_add_host() in such path. That leads
to messages like this in dmesg (and a leak of the SCSI host proc
structure):
usb-storage 4-1:87.51: USB Mass Storage device detected
proc_dir_entry 'scsi/usb-storage' already registered
WARNING: CPU: 1 PID: 3519 at fs/proc/generic.c:377 proc_register+0x347/0x4e0 fs/proc/generic.c:376
The proper fix seems to still call scsi_proc_hostdir_rm() on dev_release(),
but guard that with the state check for SHOST_CREATED; there is even a
comment in scsi_host_dev_release() detailing that: such conditional is
meant for cases where the SCSI host was allocated but there was no calls to
{add,remove}_host(), like the usb-storage case.
This is what we propose here and with that, the error path of usb-storage
does not trigger the warning anymore.
Reported-by: syzbot+c645abf505ed21f931b5@syzkaller.appspotmail.com
Fixes: be03df3d4b ("scsi: core: Fix a procfs host directory removal regression")
Cc: stable@vger.kernel.org
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: John Garry <john.g.garry@oracle.com>
Cc: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@igalia.com>
Link: https://lore.kernel.org/r/20240313113006.2834799-1-gpiccoli@igalia.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c76106cb9 upstream.
Commit 3cc2ffe5c1 ("scsi: sd: Differentiate system and runtime start/stop
management") introduced the manage_system_start_stop scsi_device flag to
allow libata to indicate to the SCSI disk driver that nothing should be
done when resuming a disk on system resume. This change turned the
execution of sd_resume() into a no-op for ATA devices on system
resume. While this solved deadlock issues during device resume, this change
also wrongly removed the execution of opal_unlock_from_suspend(). As a
result, devices with TCG OPAL locking enabled remain locked and
inaccessible after a system resume from sleep.
To fix this issue, introduce the SCSI driver resume method and implement it
with the sd_resume() function calling opal_unlock_from_suspend(). The
former sd_resume() function is renamed to sd_resume_common() and modified
to call the new sd_resume() function. For non-ATA devices, this result in
no functional changes.
In order for libata to explicitly execute sd_resume() when a device is
resumed during system restart, the function scsi_resume_device() is
introduced. libata calls this function from the revalidation work executed
on devie resume, a state that is indicated with the new device flag
ATA_DFLAG_RESUMING. Doing so, locked TCG OPAL enabled devices are unlocked
on resume, allowing normal operation.
Fixes: 3cc2ffe5c1 ("scsi: sd: Differentiate system and runtime start/stop management")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218538
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240319071209.1179257-1-dlemoal@kernel.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 051e0840ff upstream.
The dreamcastcard->timer could schedule the spu_dma_work and the
spu_dma_work could also arm the dreamcastcard->timer.
When the snd_pcm_substream is closing, the aica_channel will be
deallocated. But it could still be dereferenced in the worker
thread. The reason is that del_timer() will return directly
regardless of whether the timer handler is running or not and
the worker could be rescheduled in the timer handler. As a result,
the UAF bug will happen. The racy situation is shown below:
(Thread 1) | (Thread 2)
snd_aicapcm_pcm_close() |
... | run_spu_dma() //worker
| mod_timer()
flush_work() |
del_timer() | aica_period_elapsed() //timer
kfree(dreamcastcard->channel) | schedule_work()
| run_spu_dma() //worker
... | dreamcastcard->channel-> //USE
In order to mitigate this bug and other possible corner cases,
call mod_timer() conditionally in run_spu_dma(), then implement
PCM sync_stop op to cancel both the timer and worker. The sync_stop
op will be called from PCM core appropriately when needed.
Fixes: 198de43d75 ("[ALSA] Add ALSA support for the SEGA Dreamcast PCM device")
Suggested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Message-ID: <20240326094238.95442-1-duoming@zju.edu.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 457f730825 ]
It's possible the migration file is accessed after reset when it has
been cleaned up, especially when it's initiated by the device. This is
because the driver doesn't rip out the filep when cleaning up it only
frees the related page structures and sets its local struct
pds_vfio_lm_file pointer to NULL. This can cause a NULL pointer
dereference, which is shown in the example below during a restore after
a device initiated reset:
BUG: kernel NULL pointer dereference, address: 000000000000000c
PF: supervisor read access in kernel mode
PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 [#1] PREEMPT SMP NOPTI
RIP: 0010:pds_vfio_get_file_page+0x5d/0xf0 [pds_vfio_pci]
[...]
Call Trace:
<TASK>
pds_vfio_restore_write+0xf6/0x160 [pds_vfio_pci]
vfs_write+0xc9/0x3f0
? __fget_light+0xc9/0x110
ksys_write+0xb5/0xf0
__x64_sys_write+0x1a/0x20
do_syscall_64+0x38/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
[...]
Add a disabled flag to the driver's struct pds_vfio_lm_file that gets
set during cleanup. Then make sure to check the flag when the migration
file is accessed via its file_operations. By default this flag will be
false as the memory for struct pds_vfio_lm_file is kzalloc'd, which means
the struct pds_vfio_lm_file is enabled and accessible. Also, since the
file_operations and driver's migration file cleanup happen under the
protection of the same pds_vfio_lm_file.lock, using this flag is thread
safe.
Fixes: 8512ed2563 ("vfio/pds: Always clear the save/restore FDs on reset")
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: Brett Creeley <brett.creeley@amd.com>
Link: https://lore.kernel.org/r/20240308182149.22036-2-brett.creeley@amd.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7bdbfb4e36 ]
[Why]
If an OPP is used for a different OPTC without first being disconnected
from the previous OPTC, unexpected behaviour can occur. This also
applies to phantom pipes, which is what the current logic missed.
[How]
Disconnect OPPs from OPTC for phantom pipes before disabling OTG master.
Also move the disconnection to before the OTG master disable, since the
register is double buffered.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stable-dep-of: b4e05bb1de ("drm/amd/display: Clear OPTC mem select on disable")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e7b2b108cd ]
[Why]
Under some circumstances, disabling an OPTC and attempting to reclaim
its OPP(s) for a different OPTC could cause a hang/underflow due to OPPs
not being properly disconnected from the disabled OPTC.
[How]
Ensure that all OPPs are unassigned from an OPTC when it gets disabled.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Ilya Bakoulin <ilya.bakoulin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stable-dep-of: b4e05bb1de ("drm/amd/display: Clear OPTC mem select on disable")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit cd5432c712 upstream.
In the scenario of entering hibernation with udisk in the system, if the
udisk was gone or resume fail in the thaw phase of hibernation. Its state
will be set to NOTATTACHED. At this point, usb_hub_wq was already freezed
and can't not handle disconnect event. Next, in the poweroff phase of
hibernation, SYNCHRONIZE_CACHE SCSI command will be sent to this udisk
when poweroff this scsi device, which will cause uas_submit_urbs to be
called to submit URB for sense/data/cmd pipe. However, these URBs will
submit fail as device was set to NOTATTACHED state. Then, uas_submit_urbs
will return a value SCSI_MLQUEUE_DEVICE_BUSY to the caller. That will lead
the SCSI layer go into an ugly loop and system fail to go into hibernation.
On the other hand, when we specially check for -ENODEV in function
uas_queuecommand_lck, returning DID_ERROR to SCSI layer will cause device
poweroff fail and system shutdown instead of entering hibernation.
To fix this issue, let uas_submit_urbs to return original generic error
when submitting URB failed. At the same time, we need to translate -ENODEV
to DID_NOT_CONNECT for the SCSI layer.
Suggested-by: Oliver Neukum <oneukum@suse.com>
Cc: stable@vger.kernel.org
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Link: https://lore.kernel.org/r/20240306180814.4897-1-WeitaoWang-oc@zhaoxin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 34a956739d upstream.
E.g. ESMT chips will return an identification code with a length of 5
bytes. In order to prevent ambiguity, flash chips would actually need to
return IDs that are up to 17 or more bytes long due to JEDEC's
continuation scheme. I understand that if a manufacturer ID is located
in bank N of JEDEC's database (there are currently 16 banks), N - 1
continuation codes (7Fh) need to be added to the identification code
(comprising of manufacturer ID and device ID). However, most flash chip
manufacturers don't seem to implement this (correctly).
Signed-off-by: Ezra Buehler <ezra.buehler@husqvarnagroup.com>
Reviewed-by: Martin Kurbanov <mmkurbanov@salutedevices.com>
Tested-by: Martin Kurbanov <mmkurbanov@salutedevices.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240125200108.24374-2-ezra@easyb.ch
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c3366abdbe884be62e5a7502b4db758aa3974c6 upstream.
hci_cmd_sync_cancel_sync shall check the error passed to it since it
will be propagated using req_result which is __u32 it needs to be
properly set to a positive value if it was passed as negative othertise
IS_ERR will not trigger as -(errno) would be converted to a positive
value.
Fixes: 63298d6e75 ("Bluetooth: hci_core: Cancel request on command timeout")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Reported-and-tested-by: Thorsten Leemhuis <linux@leemhuis.info>
Closes: https://lore.kernel.org/all/08275279-7462-4f4a-a0ee-8aa015f829bc@leemhuis.info/
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e41d769f1a upstream.
Since commit 0c65dc0626 ("drm/i915/jsl: s/JSL/JASPERLAKE for
platform/subplatform defines"), boot freezes on a Jasper Lake tablet
(Librem 11), usually with graphical corruption on the eDP display,
but sometimes just a black screen. This commit was included in 6.6 and
later.
That commit was intended to refactor EHL and JSL macros, but the change
to ehl_combo_pll_div_frac_wa_needed() started matching JSL incorrectly
when it was only intended to match EHL.
It replaced:
return ((IS_PLATFORM(i915, INTEL_ELKHARTLAKE) &&
IS_JSL_EHL_DISPLAY_STEP(i915, STEP_B0, STEP_FOREVER)) ||
with:
return (((IS_ELKHARTLAKE(i915) || IS_JASPERLAKE(i915)) &&
IS_DISPLAY_STEP(i915, STEP_B0, STEP_FOREVER)) ||
Remove IS_JASPERLAKE() to fix the regression.
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
Cc: stable@vger.kernel.org
Fixes: 0c65dc0626 ("drm/i915/jsl: s/JSL/JASPERLAKE for platform/subplatform defines")
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240313135424.3731410-1-jonathon.hall@puri.sm
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit 1ef4885931)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 18846627ef upstream.
Reinstate commit 88b065943c ("drm/i915/dsi: Do display on
sequence later on icl+"), for the most part. Turns out some
machines (eg. Chuwi Minibook X) really do need that updated order.
It is also the order the Windows driver uses.
However we can't just undo the revert since that would again
break Lenovo 82TQ. After staring at the VBT sequences for both
machines I've concluded that the Lenovo 82TQ sequences look
somewhat broken:
- INIT_OTP is not present at all
- what should be in INIT_OTP is found in DISPLAY_ON
- what should be in DISPLAY_ON is found in BACKLIGHT_ON
(along with the actual backlight stuff)
The Chuwi Minibook X on the other hand has a full complement
of sequences in its VBT.
So let's try to deal with the broken sequences in the
Lenovo 82TQ VBT by simply swapping the (non-existent)
INIT_OTP sequence with the DISPLAY_ON sequence. Thus we
execute DISPLAY_ON when intending to execute INIT_OTP,
and execute nothing at all when intending to execute
DISPLAY_ON. That should be 100% equivalent to the
revert, for such broken VBTs.
Cc: stable@vger.kernel.org
Fixes: 6992eb815d ("Revert "drm/i915/dsi: Do display on sequence later on icl+"")
References: https://gitlab.freedesktop.org/drm/intel/-/issues/10071
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/10334
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240305083659.8396-1-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit 94ae4612ea)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a38a829c8 upstream.
The function platform_get_resource was replaced with
devm_platform_ioremap_resource_byname and is called using 0 as name.
This eventually ends up in platform_get_resource_byname in the call
stack, where it causes a null pointer in strcmp.
if (type == resource_type(r) && !strcmp(r->name, name))
It should have been replaced with devm_platform_ioremap_resource.
Fixes: bd69058f50 ("net: ll_temac: Use devm_platform_ioremap_resource_byname()")
Signed-off-by: Claus Hansen Ries <chr@terma.com>
Cc: stable@vger.kernel.org
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/cca18f9c630a41c18487729770b492bb@terma.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 16e87fe23d upstream.
The kcalloc() in nouveau_dmem_evict_chunk() will return null if
the physical memory has run out. As a result, if we dereference
src_pfns, dst_pfns or dma_addrs, the null pointer dereference bugs
will happen.
Moreover, the GPU is going away. If the kcalloc() fails, we could not
evict all pages mapping a chunk. So this patch adds a __GFP_NOFAIL
flag in kcalloc().
Finally, as there is no need to have physically contiguous memory,
this patch switches kcalloc() to kvcalloc() in order to avoid
failing allocations.
CC: <stable@vger.kernel.org> # v6.1
Fixes: 249881232e ("nouveau/dmem: evict device private memory during release")
Suggested-by: Danilo Krummrich <dakr@redhat.com>
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240306050104.11259-1-duoming@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a26de34b3c upstream.
The issue occurs when the devfreq cooling device uses the EM power model
and the get_real_power() callback is provided by the driver.
The EM power table is sorted ascending，can't index the table by cooling
device state，so convert cooling state to performance state by
dfc->max_state - dfc->capped_state.
Fixes: 615510fe13 ("thermal: devfreq_cooling: remove old power model and use EM")
Cc: 5.11+ <stable@vger.kernel.org> # 5.11+
Signed-off-by: Ye Zhang <ye.zhang@rock-chips.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 55251fbdf0 upstream.
This reverts commit 748dc0b65e.
Partial zone append completions cannot be supported as there is no
guarantees that the fragmented data will be written sequentially in the
same manner as with a full command. Commit 748dc0b65e ("block: fix
partial zone append completion handling in req_bio_endio()") changed
req_bio_endio() to always advance a partially failed BIO by its full
length, but this can lead to incorrect accounting. So revert this
change and let low level device drivers handle this case by always
failing completely zone append operations. With this revert, users will
still see an IO error for a partially completed zone append BIO.
Fixes: 748dc0b65e ("block: fix partial zone append completion handling in req_bio_endio()")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240328004409.594888-2-dlemoal@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9e2a5b00a upstream.
"PM runtime functions" was been added in sdhci-omap driver in commit
f433e8aac6 ("mmc: sdhci-omap: Implement PM runtime functions") along
with "card power off and enable aggressive PM" in commit 3edf588e7f
("mmc: sdhci-omap: Allow SDIO card power off and enable aggressive PM").
Since then, the sdhci-omap driver doesn't work using mmc-hs200 mode
due to the tuning values being lost during a pm transition.
As for the sdhci_am654 driver, request a new tuning sequence before
suspend (sdhci_omap_runtime_suspend()), otherwise the device will
trigger cache flush error:
mmc1: cache flush error -110 (ETIMEDOUT)
mmc1: error -110 doing aggressive suspend
followed by I/O errors produced by fdisk -l /dev/mmcblk1boot1:
I/O error, dev mmcblk1boot0, sector 64384 op 0x0:(READ) flags 0x80700 phys_seg 1
prio class 2
I/O error, dev mmcblk1boot1, sector 64384 op 0x0:(READ) flags 0x80700 phys_seg 1
prio class 2
I/O error, dev mmcblk1boot1, sector 64384 op 0x0:(READ) flags 0x0 phys_seg 1
prio class 2
Buffer I/O error on dev mmcblk1boot1, logical block 8048, async page read
I/O error, dev mmcblk1boot0, sector 64384 op 0x0:(READ) flags 0x0 phys_seg 1
prio class 2
Buffer I/O error on dev mmcblk1boot0, logical block 8048, async page read
Don't re-tune if auto retuning is supported in HW (when SDHCI_TUNING_MODE_3
is available).
Link: https://lore.kernel.org/all/2e5f1997-564c-44e4-b357-6343e0dae7ab@smile.fr
Fixes: f433e8aac6 ("mmc: sdhci-omap: Implement PM runtime functions")
Signed-off-by: Romain Naour <romain.naour@skf.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240315234444.816978-1-romain.naour@smile.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c864371b2 upstream.
Following issue was observed while running the uffd-unit-tests selftest
on ARM devices. On x86_64 no issues were detected:
pthread_create followed by fork caused deadlock in certain cases wherein
fork required some work to be completed by the created thread. Used
synchronization to ensure that created thread's start function has started
before invoking fork.
[edliaw@google.com: refactored to use atomic_bool]
Link: https://lkml.kernel.org/r/20240325194100.775052-1-edliaw@google.com
Fixes: 760aee0b71 ("selftests/mm: add tests for RO pinning vs fork()")
Signed-off-by: Lokesh Gidra <lokeshgidra@google.com>
Signed-off-by: Edward Liaw <edliaw@google.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d5d39c707a upstream.
When cachestat on shmem races with swapping and invalidation, there
are two possible bugs:
1) A swapin error can have resulted in a poisoned swap entry in the
shmem inode's xarray. Calling get_shadow_from_swap_cache() on it
will result in an out-of-bounds access to swapper_spaces[].
Validate the entry with non_swap_entry() before going further.
2) When we find a valid swap entry in the shmem's inode, the shadow
entry in the swapcache might not exist yet: swap IO is still in
progress and we're before __remove_mapping; swapin, invalidation,
or swapoff have removed the shadow from swapcache after we saw the
shmem swap entry.
This will send a NULL to workingset_test_recent(). The latter
purely operates on pointer bits, so it won't crash - node 0, memcg
ID 0, eviction timestamp 0, etc. are all valid inputs - but it's a
bogus test. In theory that could result in a false "recently
evicted" count.
Such a false positive wouldn't be the end of the world. But for
code clarity and (future) robustness, be explicit about this case.
Bail on get_shadow_from_swap_cache() returning NULL.
Link: https://lkml.kernel.org/r/20240315095556.GC581298@cmpxchg.org
Fixes: cf264e1329 ("cachestat: implement cachestat syscall")
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reported-by: Chengming Zhou <chengming.zhou@linux.dev> [Bug #1]
Reported-by: Jann Horn <jannh@google.com> [Bug #2]
Reviewed-by: Chengming Zhou <chengming.zhou@linux.dev>
Reviewed-by: Nhat Pham <nphamcs@gmail.com>
Cc: <stable@vger.kernel.org> [v6.5+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2aea94ac14 upstream.
In NOMMU kernel the value of linux_binprm::p is the offset inside the
temporary program arguments array maintained in separate pages in the
linux_binprm::page. linux_binprm::exec being a copy of linux_binprm::p
thus must be adjusted when that array is copied to the user stack.
Without that adjustment the value passed by the NOMMU kernel to the ELF
program in the AT_EXECFN entry of the aux array doesn't make any sense
and it may break programs that try to access memory pointed to by that
entry.
Adjust linux_binprm::exec before the successful return from the
transfer_args_to_stack().
Cc: <stable@vger.kernel.org>
Fixes: b6a2fea393 ("mm: variable length argument support")
Fixes: 5edc2a5123 ("binfmt_elf_fdpic: wire up AT_EXECFD, AT_EXECFN, AT_SECURE")
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Link: https://lore.kernel.org/r/20240320182607.1472887-1-jcmvbkbc@gmail.com
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit be23b2d7c3 upstream.
Wireless extensions are already disabled if MLO is enabled,
given that we cannot support MLO there with all the hard-
coded assumptions about BSSID etc.
However, the WiFi7 ecosystem is still stabilizing, and some
devices may need MLO disabled while that happens. In that
case, we might end up with a device that supports wext (but
not MLO) in one kernel, and then breaks wext in the future
(by enabling MLO), which is not desirable.
Add a flag to let such drivers/devices disable wext even if
MLO isn't yet enabled.
Cc: stable@vger.kernel.org
Link: https://msgid.link/20240314110951.b50f1dc4ec21.I656ddd8178eedb49dc5c6c0e70f8ce5807afb54f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8b70c7f86 upstream.
Commit f4a9f21941 ("btrfs: do not delete unused block group if it may be
used soon") changed the behaviour of deleting unused block-groups on zoned
filesystems. Starting with this commit, we're using
btrfs_space_info_used() to calculate the number of used bytes in a
space_info. But btrfs_space_info_used() also accounts
btrfs_space_info::bytes_zone_unusable as used bytes.
So if a block group is 100% zone_unusable it is skipped from the deletion
step.
In order not to skip fully zone_unusable block-groups, also check if the
block-group has bytes left that can be used on a zoned filesystem.
Fixes: f4a9f21941 ("btrfs: do not delete unused block group if it may be used soon")
CC: stable@vger.kernel.org # 6.1+
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef1e68236b upstream.
There are reports from tree-checker that detects corrupted nodes,
without any obvious pattern so possibly an overwrite in memory.
After some debugging it turns out there's a race when reading an extent
buffer the uptodate status can be missed.
To prevent concurrent reads for the same extent buffer,
read_extent_buffer_pages() performs these checks:
/* (1) */
if (test_bit(EXTENT_BUFFER_UPTODATE, &eb->bflags))
return 0;
/* (2) */
if (test_and_set_bit(EXTENT_BUFFER_READING, &eb->bflags))
goto done;
At this point, it seems safe to start the actual read operation. Once
that completes, end_bbio_meta_read() does
/* (3) */
set_extent_buffer_uptodate(eb);
/* (4) */
clear_bit(EXTENT_BUFFER_READING, &eb->bflags);
Normally, this is enough to ensure only one read happens, and all other
callers wait for it to finish before returning. Unfortunately, there is
a racey interleaving:
Thread A | Thread B | Thread C
---------+----------+---------
(1) | |
| (1) |
(2) | |
(3) | |
(4) | |
| (2) |
| | (1)
When this happens, thread B kicks of an unnecessary read. Worse, thread
C will see UPTODATE set and return immediately, while the read from
thread B is still in progress. This race could result in tree-checker
errors like this as the extent buffer is concurrently modified:
BTRFS critical (device dm-0): corrupted node, root=256
block=8550954455682405139 owner mismatch, have 11858205567642294356
expect [256, 18446744073709551360]
Fix it by testing UPTODATE again after setting the READING bit, and if
it's been set, skip the unnecessary read.
Fixes: d7172f52e9 ("btrfs: use per-buffer locking for extent_buffer reading")
Link: https://lore.kernel.org/linux-btrfs/CAHk-=whNdMaN9ntZ47XRKP6DBes2E5w7fi-0U3H2+PS18p+Pzw@mail.gmail.com/
Link: https://lore.kernel.org/linux-btrfs/f51a6d5d7432455a6a858d51b49ecac183e0bbc9.1706312914.git.wqu@suse.com/
Link: https://lore.kernel.org/linux-btrfs/c7241ea4-fcc6-48d2-98c8-b5ea790d6c89@gmx.com/
CC: stable@vger.kernel.org # 6.5+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tavian Barnes <tavianator@tavianator.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ minor update of changelog ]
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0a69b6b3a0 upstream.
A syzkaller reproducer found a race while attempting to remove dquot
information from the rb tree.
Fetching the rb_tree root node must also be protected by the
dqopt->dqio_sem, otherwise, giving the right timing, shmem_release_dquot()
will trigger a warning because it couldn't find a node in the tree, when
the real reason was the root node changing before the search starts:
Thread 1 Thread 2
- shmem_release_dquot() - shmem_{acquire,release}_dquot()
- fetch ROOT - Fetch ROOT
- acquire dqio_sem
- wait dqio_sem
- do something, triger a tree rebalance
- release dqio_sem
- acquire dqio_sem
- start searching for the node, but
from the wrong location, missing
the node, and triggering a warning.
Link: https://lkml.kernel.org/r/20240320124011.398847-1-cem@kernel.org
Fixes: eafc474e20 ("shmem: prepare shmem quota infrastructure")
Signed-off-by: Carlos Maiolino <cmaiolino@redhat.com>
Reported-by: Ubisectech Sirius <bugreport@ubisectech.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Hugh Dickins <hughd@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit decd347c2a upstream.
Commit
8117961d98 ("x86/efi: Disregard setup header of loaded image")
dropped the memcopy of the image's setup header into the boot_params
struct provided to the core kernel, on the basis that EFI boot does not
need it and should rely only on a single protocol to interface with the
boot chain. It is also a prerequisite for being able to increase the
section alignment to 4k, which is needed to enable memory protections
when running in the boot services.
So only the setup_header fields that matter to the core kernel are
populated explicitly, and everything else is ignored. One thing was
overlooked, though: the initrd_addr_max field in the setup_header is not
used by the core kernel, but it is used by the EFI stub itself when it
loads the initrd, where its default value of INT_MAX is used as the soft
limit for memory allocation.
This means that, in the old situation, the initrd was virtually always
loaded in the lower 2G of memory, but now, due to initrd_addr_max being
0x0, the initrd may end up anywhere in memory. This should not be an
issue principle, as most systems can deal with this fine. However, it
does appear to tickle some problems in older UEFI implementations, where
the memory ends up being corrupted, resulting in errors when unpacking
the initramfs.
So set the initrd_addr_max field to INT_MAX like it was before.
Fixes: 8117961d98 ("x86/efi: Disregard setup header of loaded image")
Reported-by: Radek Podgorny <radek@podgorny.cz>
Closes: https://lore.kernel.org/all/a99a831a-8ad5-4cb0-bff9-be637311f771@podgorny.cz
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61d130f261 upstream.
Avoid a type mismatch warning in max() by switching to max_t() and
providing the type explicitly.
Fixes: 3cb4a48275 ("efi/libstub: fix efi_random_alloc() ...")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d21f5a59ea upstream.
The pure EFI stub entry point does not take a struct boot_params from
the boot loader, but creates it from scratch, and populates only the
fields that still have meaning in this context (command line, initrd
base and size, etc)
The original mixed mode implementation used the EFI handover protocol
instead, where the boot loader (i.e., GRUB) populates a boot_params
struct and passes it to a special Linux specific EFI entry point that
takes the boot_params pointer as its third argument.
When the new mixed mode implementation was introduced, using a special
32-bit PE entrypoint in the 64-bit kernel, it adopted the pure approach,
and relied on the EFI stub to create the struct boot_params. This is
preferred because it makes the bootloader side much easier to implement,
as it does not need any x86-specific knowledge on how struct boot_params
and struct setup_header are put together. This mixed mode implementation
was adopted by systemd-boot version 252 and later.
When commit
e2ab9eab32 ("x86/boot/compressed: Move 32-bit entrypoint code into .text section")
refactored this code and moved it out of head_64.S, the fact that ESI
was populated with the address of the base of the image was overlooked,
and to simplify the code flow, ESI is now zeroed and stored to memory
unconditionally in shared code, so that the NULL-ness of that variable
can still be used later to determine which mixed mode boot protocol is
in use.
With ESI pointing to the base of the image, it can serve as a struct
boot_params pointer for startup_32(), which only accesses the init_data
and kernel_alignment fields (and the scratch field as a temporary
stack). Zeroing ESI means that those accesses produce garbage now, even
though things appear to work if the first page of memory happens to be
zeroed, and the region right before LOAD_PHYSICAL_ADDR (== 16 MiB)
happens to be free.
The solution is to pass a special, temporary struct boot_params to
startup_32() via ESI, one that is sufficient for getting it to create
the page tables correctly and is discarded right after. This involves
setting a minimal alignment of 4k, only to get the statically allocated
page tables line up correctly, and setting init_size to the executable
image size (_end - startup_32). This ensures that the page tables are
covered by the static footprint of the PE image.
Given that EFI boot no longer calls the decompressor and no longer pads
the image to permit the decompressor to execute in place, the same
temporary struct boot_params should be used in the EFI handover protocol
based mixed mode implementation as well, to prevent the page tables from
being placed outside of allocated memory.
Fixes: e2ab9eab32 ("x86/boot/compressed: Move 32-bit entrypoint code into .text section")
Cc: <stable@kernel.org> # v6.1+
Closes: https://lore.kernel.org/all/20240321150510.GI8211@craftyguy.net/
Reported-by: Clayton Craft <clayton@craftyguy.net>
Tested-by: Clayton Craft <clayton@craftyguy.net>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ae065d0ce9 upstream.
The "Speaker Digital Gain" kcontrol controls the TAS2781_DVC_LVL (0x1A)
register. Unfortunately the tas2563 does not have DVC_LVL, but has
INT_MASK0 in 0x1A, which has been misused so far.
Since commit c1947ce61f ("ALSA: hda/realtek: tas2781: enable subwoofer
volume control") the volume of the tas2781 amplifiers can be controlled
by the master volume, so this digital gain kcontrol is not needed.
Remove it.
Fixes: 5be27f1e3e ("ALSA: hda/tas2781: Add tas2781 HDA driver")
CC: stable@vger.kernel.org
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Message-ID: <741fc21db994efd58f83e7aef38931204961e5b2.1711469583.git.soyer@irl.hu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5fa695e7da upstream.
perf top errors out on a hybrid machine
$perf top
Error:
The cycles:P event is not supported.
The perf top expects that the "cycles" is collected on all CPUs in the
system. But for hybrid there is no single "cycles" event which can cover
all CPUs. Perf has to split it into two cycles events, e.g.,
cpu_core/cycles/ and cpu_atom/cycles/. Each event has its own CPU mask.
If a event is opened on the unsupported CPU. The open fails. That's the
reason of the above error out.
Perf should only open the cycles event on the corresponding CPU. The
commit ef91871c96 ("perf evlist: Propagate user CPU maps intersecting
core PMU maps") intersect the requested CPU map with the CPU map of the
PMU. Use the evsel's cpus to replace user_requested_cpus.
The evlist's threads are also propagated to the evsel's threads in
__perf_evlist__propagate_maps(). For a system-wide event, perf appends
a dummy event and assign it to the evsel's threads. For a per-thread
event, the evlist's thread_map is assigned to the evsel's threads. The
same as the other tools, e.g., perf record, using the evsel's threads
when opening an event.
Reported-by: Arnaldo Carvalho de Melo <acme@kernel.org>
Reviewed-by: Ian Rogers <irogers@google.com>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Hector Martin <marcan@marcan.st>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Closes: https://lore.kernel.org/linux-perf-users/ZXNnDrGKXbEELMXV@kernel.org/
Link: https://lore.kernel.org/r/20231214144612.1092028-1-kan.liang@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8b65ef5ad4 ]
Add missing flags argument to open(2) call with O_CREAT.
Some tests fail to compile if _FORTIFY_SOURCE is defined (to any valid
value) (together with -O), resulting in similar error messages such as:
In file included from /usr/include/fcntl.h:342,
from gup_test.c:1:
In function 'open',
inlined from 'main' at gup_test.c:206:10:
/usr/include/bits/fcntl2.h:50:11: error: call to '__open_missing_mode' declared with attribute error: open with O_CREAT or O_TMPFILE in second argument needs 3 arguments
50 | __open_missing_mode ();
| ^~~~~~~~~~~~~~~~~~~~~~
_FORTIFY_SOURCE is enabled by default in some distributions, so the
tests are not built by default and are skipped.
open(2) man-page warns about missing flags argument: "if it is not
supplied, some arbitrary bytes from the stack will be applied as the
file mode."
Link: https://lkml.kernel.org/r/20240318023445.3192922-1-vt@altlinux.org
Fixes: aeb85ed4f4 ("tools/testing/selftests/vm/gup_benchmark.c: allow user specified file")
Fixes: fbe37501b2 ("mm: huge_memory: debugfs for file-backed THP split")
Fixes: c942f5bd17 ("selftests: soft-dirty: add test for mprotect")
Signed-off-by: Vitaly Chikunov <vt@altlinux.org>
Reviewed-by: Zi Yan <ziy@nvidia.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Cc: Keith Busch <kbusch@kernel.org>
Cc: Peter Xu <peterx@redhat.com>
Cc: Yang Shi <shy828301@gmail.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Nadav Amit <nadav.amit@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9eb05877db ]
22e8e19 has introduced a regression in the imgchip->pwm_clk lookup, whereas
the clock name has also been renamed to "imgchip". This causes the driver
failing to load:
[ 0.546905] img-pwm 18101300.pwm: failed to get imgchip clock
[ 0.553418] img-pwm: probe of 18101300.pwm failed with error -2
Fix this lookup by reverting the clock name back to "pwm".
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Link: https://lore.kernel.org/r/20240320083602.81592-1-wigyori@uid0.hu
Fixes: 22e8e19a46 ("pwm: img: Rename variable pointing to driver private data")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62b71cd73d ]
Check if get_next_variable() is actually valid pointer before
calling it. In kdump kernel this method is set to NULL that causes
panic during the kexec-ed kernel boot.
Tested with QEMU and OVMF firmware.
Fixes: bad267f9e1 ("efi: verify that variable services are supported")
Signed-off-by: Oleksandr Tymoshenko <ovt@google.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 10e4b5166d ]
Commit 672365477a ("x86/fpu: Update XFD state where required") and
commit 8bf26758ca ("x86/fpu: Add XFD state to fpstate") introduced a
per CPU variable xfd_state to keep the MSR_IA32_XFD value cached, in
order to avoid unnecessary writes to the MSR.
On CPU hotplug MSR_IA32_XFD is reset to the init_fpstate.xfd, which
wipes out any stale state. But the per CPU cached xfd value is not
reset, which brings them out of sync.
As a consequence a subsequent xfd_update_state() might fail to update
the MSR which in turn can result in XRSTOR raising a #NM in kernel
space, which crashes the kernel.
To fix this, introduce xfd_set_state() to write xfd_state together
with MSR_IA32_XFD, and use it in all places that set MSR_IA32_XFD.
Fixes: 672365477a ("x86/fpu: Update XFD state where required")
Signed-off-by: Adamos Ttofari <attofari@amazon.de>
Signed-off-by: Chang S. Bae <chang.seok.bae@intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240322230439.456571-1-chang.seok.bae@intel.com
Closes: https://lore.kernel.org/lkml/20230511152818.13839-1-attofari@amazon.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3cb4a48275 ]
Following warning is sometimes observed while booting my servers:
[ 3.594838] DMA: preallocated 4096 KiB GFP_KERNEL pool for atomic allocations
[ 3.602918] swapper/0: page allocation failure: order:10, mode:0xcc1(GFP_KERNEL|GFP_DMA), nodemask=(null),cpuset=/,mems_allowed=0-1
...
[ 3.851862] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA pool for atomic allocation
If 'nokaslr' boot option is set, the warning always happens.
On x86, ZONE_DMA is small zone at the first 16MB of physical address
space. When this problem happens, most of that space seems to be used by
decompressed kernel. Thereby, there is not enough space at DMA_ZONE to
meet the request of DMA pool allocation.
The commit 2f77465b05 ("x86/efistub: Avoid placing the kernel below
LOAD_PHYSICAL_ADDR") tried to fix this problem by introducing lower
bound of allocation.
But the fix is not complete.
efi_random_alloc() allocates pages by following steps.
1. Count total available slots ('total_slots')
2. Select a slot ('target_slot') to allocate randomly
3. Calculate a starting address ('target') to be included target_slot
4. Allocate pages, which starting address is 'target'
In step 1, 'alloc_min' is used to offset the starting address of memory
chunk. But in step 3 'alloc_min' is not considered at all. As the
result, 'target' can be miscalculated and become lower than 'alloc_min'.
When KASLR is disabled, 'target_slot' is always 0 and the problem
happens everytime if the EFI memory map of the system meets the
condition.
Fix this problem by calculating 'target' considering 'alloc_min'.
Cc: linux-efi@vger.kernel.org
Cc: Tom Englund <tomenglund26@gmail.com>
Cc: linux-kernel@vger.kernel.org
Fixes: 2f77465b05 ("x86/efistub: Avoid placing the kernel below LOAD_PHYSICAL_ADDR")
Signed-off-by: Kazuma Kondo <kazuma-kondo@nec.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e51653d5d ]
Read from an unsafe address with copy_from_kernel_nofault() in
arch_adjust_kprobe_addr() because this function is used before checking
the address is in text or not. Syzcaller bot found a bug and reported
the case if user specifies inaccessible data area,
arch_adjust_kprobe_addr() will cause a kernel panic.
[ mingo: Clarified the comment. ]
Fixes: cc66bb9145 ("x86/ibt,kprobes: Cure sym+0 equals fentry woes")
Reported-by: Qiang Zhang <zzqq0103.hey@gmail.com>
Tested-by: Jinghao Jia <jinghao7@illinois.edu>
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/171042945004.154897.2221804961882915806.stgit@devnote2
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 853a603030 ]
RZ/G2L interrupt chips require that the interrupt is masked before changing
the NMI, IRQ, TINT interrupt settings. Aside of that, after setting an edge
trigger type it is required to clear the interrupt status register in order
to avoid spurious interrupts.
The current implementation fails to do either of that and therefore is
prone to generate spurious interrupts when setting the trigger type.
Address this by:
- Ensuring that the interrupt is masked at the chip level across the
update for the TINT chip
- Clearing the interrupt status register after updating the trigger mode
for edge type interrupts
[ tglx: Massaged changelog and reverted the spin_lock_irqsave() change as
the set_type() callback is always called with interrupts disabled. ]
Fixes: 3fed09559c ("irqchip: Add RZ/G2L IA55 Interrupt Controller driver")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9eec61df55 ]
The irq_eoi() callback of the RZ/G2L interrupt chip clears the relevant
interrupt cause bit in the TSCR register by writing to it.
This write is not sufficient because the write is posted and therefore not
guaranteed to immediately clear the bit. Due to that delay the CPU can
raise the just handled interrupt again.
Prevent this by reading the register back which causes the posted write to
be flushed to the hardware before the read completes.
Fixes: 3fed09559c ("irqchip: Add RZ/G2L IA55 Interrupt Controller driver")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef88eefb1a ]
The RZ/G2L manual (chapter "IRQ Status Control Register (ISCR)") describes
the operation to clear interrupts through the ISCR register as follows:
[Write operation]
When "Falling-edge detection", "Rising-edge detection" or
"Falling/Rising-edge detection" is set in IITSR:
- In case ISTAT is 1
0: IRQn interrupt detection status is cleared.
1: Invalid to write.
- In case ISTAT is 0
Invalid to write.
When "Low-level detection" is set in IITSR.:
Invalid to write.
Take the interrupt type into account when clearing interrupts through the
ISCR register to avoid writing the ISCR when the interrupt type is level.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231120111820.87398-6-claudiu.beznea.uj@bp.renesas.com
Stable-dep-of: 9eec61df55 ("irqchip/renesas-rzg2l: Flush posted write in irq_eoi()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit afc5aa46ed ]
The swiotlb does not support a mapping size > swiotlb_max_mapping_size().
On the other hand, with a 64KB PAGE_SIZE configuration, it's observed that
an NVME device can map a size between 300KB~512KB, which certainly failed
the swiotlb mappings, though the default pool of swiotlb has many slots:
systemd[1]: Started Journal Service.
=> nvme 0000:00:01.0: swiotlb buffer is full (sz: 327680 bytes), total 32768 (slots), used 32 (slots)
note: journal-offline[392] exited with irqs disabled
note: journal-offline[392] exited with preempt_count 1
Call trace:
[ 3.099918] swiotlb_tbl_map_single+0x214/0x240
[ 3.099921] iommu_dma_map_page+0x218/0x328
[ 3.099928] dma_map_page_attrs+0x2e8/0x3a0
[ 3.101985] nvme_prep_rq.part.0+0x408/0x878 [nvme]
[ 3.102308] nvme_queue_rqs+0xc0/0x300 [nvme]
[ 3.102313] blk_mq_flush_plug_list.part.0+0x57c/0x600
[ 3.102321] blk_add_rq_to_plug+0x180/0x2a0
[ 3.102323] blk_mq_submit_bio+0x4c8/0x6b8
[ 3.103463] __submit_bio+0x44/0x220
[ 3.103468] submit_bio_noacct_nocheck+0x2b8/0x360
[ 3.103470] submit_bio_noacct+0x180/0x6c8
[ 3.103471] submit_bio+0x34/0x130
[ 3.103473] ext4_bio_write_folio+0x5a4/0x8c8
[ 3.104766] mpage_submit_folio+0xa0/0x100
[ 3.104769] mpage_map_and_submit_buffers+0x1a4/0x400
[ 3.104771] ext4_do_writepages+0x6a0/0xd78
[ 3.105615] ext4_writepages+0x80/0x118
[ 3.105616] do_writepages+0x90/0x1e8
[ 3.105619] filemap_fdatawrite_wbc+0x94/0xe0
[ 3.105622] __filemap_fdatawrite_range+0x68/0xb8
[ 3.106656] file_write_and_wait_range+0x84/0x120
[ 3.106658] ext4_sync_file+0x7c/0x4c0
[ 3.106660] vfs_fsync_range+0x3c/0xa8
[ 3.106663] do_fsync+0x44/0xc0
Since untrusted devices might go down the swiotlb pathway with dma-iommu,
these devices should not map a size larger than swiotlb_max_mapping_size.
To fix this bug, add iommu_dma_max_mapping_size() for untrusted devices to
take into account swiotlb_max_mapping_size() v.s. iova_rcache_range() from
the iommu_dma_opt_mapping_size().
Fixes: 82612d66d5 ("iommu: Allow the dma-iommu api to use bounce buffers")
Link: https://lore.kernel.org/r/ee51a3a5c32cf885b18f6416171802669f4a718a.1707851466.git.nicolinc@nvidia.com
Signed-off-by: Nicolin Chen <nicolinc@nvidia.com>
[will: Drop redundant is_swiotlb_active(dev) check]
Signed-off-by: Will Deacon <will@kernel.org>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Nicolin Chen <nicolinc@nvidia.com>
Tested-by: Michael Kelley <mhklinux@outlook.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51b30ecb73 ]
Nicolin reports that swiotlb buffer allocations fail for an NVME device
behind an IOMMU using 64KiB pages. This is because we end up with a
minimum allocation alignment of 64KiB (for the IOMMU to map the buffer
safely) but a minimum DMA alignment mask corresponding to a 4KiB NVME
page (i.e. preserving the 4KiB page offset from the original allocation).
If the original address is not 4KiB-aligned, the allocation will fail
because swiotlb_search_pool_area() erroneously compares these unmasked
bits with the 64KiB-aligned candidate allocation.
Tweak swiotlb_search_pool_area() so that the DMA alignment mask is
reduced based on the required alignment of the allocation.
Fixes: 82612d66d5 ("iommu: Allow the dma-iommu api to use bounce buffers")
Link: https://lore.kernel.org/r/cover.1707851466.git.nicolinc@nvidia.com
Reported-by: Nicolin Chen <nicolinc@nvidia.com>
Signed-off-by: Will Deacon <will@kernel.org>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Tested-by: Nicolin Chen <nicolinc@nvidia.com>
Tested-by: Michael Kelley <mhklinux@outlook.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cbf53074a5 ]
core-api/dma-api-howto.rst states the following properties of
dma_alloc_coherent():
| The CPU virtual address and the DMA address are both guaranteed to
| be aligned to the smallest PAGE_SIZE order which is greater than or
| equal to the requested size.
However, swiotlb_alloc() passes zero for the 'alloc_align_mask'
parameter of swiotlb_find_slots() and so this property is not upheld.
Instead, allocations larger than a page are aligned to PAGE_SIZE,
Calculate the mask corresponding to the page order suitable for holding
the allocation and pass that to swiotlb_find_slots().
Fixes: e81e99bacc ("swiotlb: Support aligned swiotlb buffers")
Signed-off-by: Will Deacon <will@kernel.org>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Reviewed-by: Petr Tesarik <petr.tesarik1@huawei-partners.com>
Tested-by: Nicolin Chen <nicolinc@nvidia.com>
Tested-by: Michael Kelley <mhklinux@outlook.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04867a7a33 ]
Commit bbb73a103f ("swiotlb: fix a braino in the alignment check fix"),
which was a fix for commit 0eee5ae102 ("swiotlb: fix slot alignment
checks"), causes a functional regression with vsock in a virtual machine
using bouncing via a restricted DMA SWIOTLB pool.
When virtio allocates the virtqueues for the vsock device using
dma_alloc_coherent(), the SWIOTLB search can return page-unaligned
allocations if 'area->index' was left unaligned by a previous allocation
from the buffer:
# Final address in brackets is the SWIOTLB address returned to the caller
| virtio-pci 0000:00:07.0: orig_addr 0x0 alloc_size 0x2000, iotlb_align_mask 0x800 stride 0x2: got slot 1645-1649/7168 (0x98326800)
| virtio-pci 0000:00:07.0: orig_addr 0x0 alloc_size 0x2000, iotlb_align_mask 0x800 stride 0x2: got slot 1649-1653/7168 (0x98328800)
| virtio-pci 0000:00:07.0: orig_addr 0x0 alloc_size 0x2000, iotlb_align_mask 0x800 stride 0x2: got slot 1653-1657/7168 (0x9832a800)
This ends badly (typically buffer corruption and/or a hang) because
swiotlb_alloc() is expecting a page-aligned allocation and so blindly
returns a pointer to the 'struct page' corresponding to the allocation,
therefore double-allocating the first half (2KiB slot) of the 4KiB page.
Fix the problem by treating the allocation alignment separately to any
additional alignment requirements from the device, using the maximum
of the two as the stride to search the buffer slots and taking care
to ensure a minimum of page-alignment for buffers larger than a page.
This also resolves swiotlb allocation failures occuring due to the
inclusion of ~PAGE_MASK in 'iotlb_align_mask' for large allocations and
resulting in alignment requirements exceeding swiotlb_max_mapping_size().
Fixes: bbb73a103f ("swiotlb: fix a braino in the alignment check fix")
Fixes: 0eee5ae102 ("swiotlb: fix slot alignment checks")
Signed-off-by: Will Deacon <will@kernel.org>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Reviewed-by: Petr Tesarik <petr.tesarik1@huawei-partners.com>
Tested-by: Nicolin Chen <nicolinc@nvidia.com>
Tested-by: Michael Kelley <mhklinux@outlook.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb13b11d53 ]
When a probe is registered at the trace_sys_enter() tracepoint, and that
probe changes the system call number, the old system call still gets
executed. This worked correctly until commit b6ec413461 ("core/entry:
Report syscall correctly for trace and audit"), which removed the
re-evaluation of the syscall number after the trace point.
Restore the original semantics by re-evaluating the system call number
after trace_sys_enter().
The performance impact of this re-evaluation is minimal because it only
takes place when a trace point is active, and compared to the actual trace
point overhead the read from a cache hot variable is negligible.
Fixes: b6ec413461 ("core/entry: Report syscall correctly for trace and audit")
Signed-off-by: André Rösti <an.roesti@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240311211704.7262-1-an.roesti@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c66c6f4e2 ]
Since commit a4d5613c4d ("arm: extend pfn_valid to take into account
freed memory map alignment") changes the semantics of pfn_valid() to check
presence of the memory map for a PFN. A valid page for an address which
is reserved but not mapped by the kernel[1], the system crashed during
some uio test with the following memory layout:
node 0: [mem 0x00000000c0a00000-0x00000000cc8fffff]
node 0: [mem 0x00000000d0000000-0x00000000da1fffff]
the uio layout is：0xc0900000, 0x100000
the crash backtrace like:
Unable to handle kernel paging request at virtual address bff00000
[...]
CPU: 1 PID: 465 Comm: startapp.bin Tainted: G O 5.10.0 #1
Hardware name: Generic DT based system
PC is at b15_flush_kern_dcache_area+0x24/0x3c
LR is at __sync_icache_dcache+0x6c/0x98
[...]
(b15_flush_kern_dcache_area) from (__sync_icache_dcache+0x6c/0x98)
(__sync_icache_dcache) from (set_pte_at+0x28/0x54)
(set_pte_at) from (remap_pfn_range+0x1a0/0x274)
(remap_pfn_range) from (uio_mmap+0x184/0x1b8 [uio])
(uio_mmap [uio]) from (__mmap_region+0x264/0x5f4)
(__mmap_region) from (__do_mmap_mm+0x3ec/0x440)
(__do_mmap_mm) from (do_mmap+0x50/0x58)
(do_mmap) from (vm_mmap_pgoff+0xfc/0x188)
(vm_mmap_pgoff) from (ksys_mmap_pgoff+0xac/0xc4)
(ksys_mmap_pgoff) from (ret_fast_syscall+0x0/0x5c)
Code: e0801001 e2423001 e1c00003 f57ff04f (ee070f3e)
---[ end trace 09cf0734c3805d52 ]---
Kernel panic - not syncing: Fatal exception
So check if PG_reserved was set to solve this issue.
[1]: https://lore.kernel.org/lkml/Zbtdue57RO0QScJM@linux.ibm.com/
Fixes: a4d5613c4d ("arm: extend pfn_valid to take into account freed memory map alignment")
Suggested-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Yongqiang Liu <liuyongqiang13@huawei.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b9920fdd5a ]
PJ4 is a v7 core that incorporates a iWMMXt coprocessor. However, GCC
does not support this combination (its iWMMXt configuration always
implies v5te), and so there is no v6/v7 user space that actually makes
use of this, beyond generic support for things like setjmp() that
preserve/restore the iWMMXt register file using generic LDC/STC
instructions emitted in assembler. As [0] appears to imply, this logic
is triggered for the init process at boot, and so most user threads will
have a iWMMXt register context associated with it, even though it is
never used.
At this point, it is highly unlikely that such GCC support will ever
materialize (and Clang does not implement support for iWMMXt to begin
with).
This means that advertising iWMMXt support on these cores results in
context switch overhead without any associated benefit, and so it is
better to simply ignore the iWMMXt unit on these systems. So rip out the
support. Doing so also fixes the issue reported in [0] related to UNDEF
handling of co-processor #0/#1 instructions issued from user space
running in Thumb2 mode.
The PJ4 cores are used in four platforms: Armada 370/xp, Dove (Cubox,
d2plug), MMP2 (xo-1.75) and Berlin (Google TV). Out of these, only the
first is still widely used, but that one actually doesn't have iWMMXt
but instead has only VFPV3-D16, and so it is not impacted by this
change.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218427 [0]
Fixes: 8bcba70cb5 ("ARM: entry: Disregard Thumb undef exception ...")
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Reviewed-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1c811d403a upstream.
The early startup code executes from a 1:1 mapping of memory, which
differs from the mapping that the code was linked and/or relocated to
run at. The latter mapping is not active yet at this point, and so
symbol references that rely on it will fault.
Given that the core kernel is built without -fPIC, symbol references are
typically emitted as absolute, and so any such references occuring in
the early startup code will therefore crash the kernel.
While an attempt was made to work around this for the early SEV/SME
startup code, by forcing RIP-relative addressing for certain global
SEV/SME variables via inline assembly (see snp_cpuid_get_table() for
example), RIP-relative addressing must be pervasively enforced for
SEV/SME global variables when accessed prior to page table fixups.
__startup_64() already handles this issue for select non-SEV/SME global
variables using fixup_pointer(), which adjusts the pointer relative to a
`physaddr` argument. To avoid having to pass around this `physaddr`
argument across all functions needing to apply pointer fixups, introduce
a macro RIP_RELATIVE_REF() which generates a RIP-relative reference to
a given global variable. It is used where necessary to force
RIP-relative accesses to global variables.
For backporting purposes, this patch makes no attempt at cleaning up
other occurrences of this pattern, involving either inline asm or
fixup_pointer(). Those will be addressed later.
[ bp: Call it "rip_rel_ref" everywhere like other code shortens
"rIP-relative reference" and make the asm wrapper __always_inline. ]
Co-developed-by: Kevin Loughlin <kevinloughlin@google.com>
Signed-off-by: Kevin Loughlin <kevinloughlin@google.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Cc: <stable@kernel.org>
Link: https://lore.kernel.org/all/20240130220845.1978329-1-kevinloughlin@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7447d911af upstream.
The eventfd_ctx trigger pointer of the vfio_fsl_mc_irq object is
initially NULL and may become NULL if the user sets the trigger
eventfd to -1. The interrupt handler itself is guaranteed that
trigger is always valid between request_irq() and free_irq(), but
the loopback testing mechanisms to invoke the handler function
need to test the trigger. The triggering and setting ioctl paths
both make use of igate and are therefore mutually exclusive.
The vfio-fsl-mc driver does not make use of irqfds, nor does it
support any sort of masking operations, therefore unlike vfio-pci
and vfio-platform, the flow can remain essentially unchanged.
Cc: Diana Craciun <diana.craciun@oss.nxp.com>
Cc: <stable@vger.kernel.org>
Fixes: cc0ee20bd9 ("vfio/fsl-mc: trigger an interrupt via eventfd")
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/r/20240308230557.805580-8-alex.williamson@redhat.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 675daf435e upstream.
The vfio-platform SET_IRQS ioctl currently allows loopback triggering of
an interrupt before a signaling eventfd has been configured by the user,
which thereby allows a NULL pointer dereference.
Rather than register the IRQ relative to a valid trigger, register all
IRQs in a disabled state in the device open path. This allows mask
operations on the IRQ to nest within the overall enable state governed
by a valid eventfd signal. This decouples @masked, protected by the
@locked spinlock from @trigger, protected via the @igate mutex.
In doing so, it's guaranteed that changes to @trigger cannot race the
IRQ handlers because the IRQ handler is synchronously disabled before
modifying the trigger, and loopback triggering of the IRQ via ioctl is
safe due to serialization with trigger changes via igate.
For compatibility, request_irq() failures are maintained to be local to
the SET_IRQS ioctl rather than a fatal error in the open device path.
This allows, for example, a userspace driver with polling mode support
to continue to work regardless of moving the request_irq() call site.
This necessarily blocks all SET_IRQS access to the failed index.
Cc: Eric Auger <eric.auger@redhat.com>
Cc: <stable@vger.kernel.org>
Fixes: 57f972e2b3 ("vfio/platform: trigger an interrupt via eventfd")
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/r/20240308230557.805580-7-alex.williamson@redhat.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 18c198c96a upstream.
A vulnerability exists where the eventfd for INTx signaling can be
deconfigured, which unregisters the IRQ handler but still allows
eventfds to be signaled with a NULL context through the SET_IRQS ioctl
or through unmask irqfd if the device interrupt is pending.
Ideally this could be solved with some additional locking; the igate
mutex serializes the ioctl and config space accesses, and the interrupt
handler is unregistered relative to the trigger, but the irqfd path
runs asynchronous to those. The igate mutex cannot be acquired from the
atomic context of the eventfd wake function. Disabling the irqfd
relative to the eventfd registration is potentially incompatible with
existing userspace.
As a result, the solution implemented here moves configuration of the
INTx interrupt handler to track the lifetime of the INTx context object
and irq_type configuration, rather than registration of a particular
trigger eventfd. Synchronization is added between the ioctl path and
eventfd_signal() wrapper such that the eventfd trigger can be
dynamically updated relative to in-flight interrupts or irqfd callbacks.
Cc: <stable@vger.kernel.org>
Fixes: 89e1f7d4c6 ("vfio: Add PCI device driver")
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/r/20240308230557.805580-5-alex.williamson@redhat.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b620ecbd17 upstream.
In order to synchronize changes that can affect the thread callback,
introduce an interface to force a flush of the inject workqueue. The
irqfd pointer is only valid under spinlock, but the workqueue cannot
be flushed under spinlock. Therefore the flush work for the irqfd is
queued under spinlock. The vfio_irqfd_cleanup_wq workqueue is re-used
for queuing this work such that flushing the workqueue is also ordered
relative to shutdown.
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/r/20240308230557.805580-4-alex.williamson@redhat.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Stable-dep-of: 18c198c96a ("vfio/pci: Create persistent INTx handler")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b0ad381fa7 upstream.
While working on the patchset to remove extent locking I got a lockdep
splat with fiemap and pagefaulting with my new extent lock replacement
lock.
This deadlock exists with our normal code, we just don't have lockdep
annotations with the extent locking so we've never noticed it.
Since we're copying the fiemap extent to user space on every iteration
we have the chance of pagefaulting. Because we hold the extent lock for
the entire range we could mkwrite into a range in the file that we have
mmap'ed. This would deadlock with the following stack trace
[<0>] lock_extent+0x28d/0x2f0
[<0>] btrfs_page_mkwrite+0x273/0x8a0
[<0>] do_page_mkwrite+0x50/0xb0
[<0>] do_fault+0xc1/0x7b0
[<0>] __handle_mm_fault+0x2fa/0x460
[<0>] handle_mm_fault+0xa4/0x330
[<0>] do_user_addr_fault+0x1f4/0x800
[<0>] exc_page_fault+0x7c/0x1e0
[<0>] asm_exc_page_fault+0x26/0x30
[<0>] rep_movs_alternative+0x33/0x70
[<0>] _copy_to_user+0x49/0x70
[<0>] fiemap_fill_next_extent+0xc8/0x120
[<0>] emit_fiemap_extent+0x4d/0xa0
[<0>] extent_fiemap+0x7f8/0xad0
[<0>] btrfs_fiemap+0x49/0x80
[<0>] __x64_sys_ioctl+0x3e1/0xb50
[<0>] do_syscall_64+0x94/0x1a0
[<0>] entry_SYSCALL_64_after_hwframe+0x6e/0x76
I wrote an fstest to reproduce this deadlock without my replacement lock
and verified that the deadlock exists with our existing locking.
To fix this simply don't take the extent lock for the entire duration of
the fiemap. This is safe in general because we keep track of where we
are when we're searching the tree, so if an ordered extent updates in
the middle of our fiemap call we'll still emit the correct extents
because we know what offset we were on before.
The only place we maintain the lock is searching delalloc. Since the
delalloc stuff can change during writeback we want to lock the extent
range so we have a consistent view of delalloc at the time we're
checking to see if we need to set the delalloc flag.
With this patch applied we no longer deadlock with my testcase.
CC: stable@vger.kernel.org # 6.1+
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 881f78f472 upstream.
[backport: resolve merge conflicts due to refactoring rtbitmap/summary
macros and accessors]
I mistakenly turned off CONFIG_XFS_RT in the Kconfig file for arm64
variant of the djwong-wtf git branch. Unfortunately, it took me a good
hour to figure out that RT wasn't built because this is what got printed
to dmesg:
XFS (sda2): realtime geometry sanity check failed
XFS (sda2): Metadata corruption detected at xfs_sb_read_verify+0x170/0x190 [xfs], xfs_sb block 0x0
Whereas I would have expected:
XFS (sda2): Not built with CONFIG_XFS_RT
XFS (sda2): RT mount failed
The root cause of these problems is the conditional compilation of the
new functions xfs_validate_rtextents and xfs_compute_rextslog that I
introduced in the two commits listed below. The !RT versions of these
functions return false and 0, respectively, which causes primary
superblock validation to fail, which explains the first message.
Move the two functions to other parts of libxfs that are not
conditionally defined by CONFIG_XFS_RT and remove the broken stubs so
that validation works again.
Fixes: e14293803f ("xfs: don't allow overly small or large realtime volumes")
Fixes: a6a38f309a ("xfs: make rextslog computation consistent with mkfs")
Signed-off-by: "Darrick J. Wong" <djwong@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Chandan Babu R <chandanbabu@kernel.org>
Signed-off-by: Catherine Hoang <catherine.hoang@oracle.com>
Acked-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 82ef1a5356 upstream.
In XFS_DAS_NODE_REMOVE_ATTR case, xfs_attr_mode_remove_attr() sets
filter to XFS_ATTR_INCOMPLETE. The filter is then reset in
xfs_attr_complete_op() if XFS_DA_OP_REPLACE operation is performed.
The filter is not reset though if XFS just removes the attribute
(args->value == NULL) with xfs_attr_defer_remove(). attr code goes
to XFS_DAS_DONE state.
Fix this by always resetting XFS_ATTR_INCOMPLETE filter. The replace
operation already resets this filter in anyway and others are
completed at this step hence don't need it.
Fixes: fdaf1bb3ca ("xfs: ATTR_REPLACE algorithm with LARP enabled needs rework")
Signed-off-by: Andrey Albershteyn <aalbersh@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Chandan Babu R <chandanbabu@kernel.org>
Signed-off-by: Catherine Hoang <catherine.hoang@oracle.com>
Acked-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5759aa4f95 upstream.
xfs_da3_swap_lastblock() copy the last block content to the dead block,
but do not update the metadata in it. We need update some metadata
for some kinds of type block, such as dir3 leafn block records its
blkno, we shall update it to the dead block blkno. Otherwise,
before write the xfs_buf to disk, the verify_write() will fail in
blk_hdr->blkno != xfs_buf->b_bn, then xfs will be shutdown.
We will get this warning:
XFS (dm-0): Metadata corruption detected at xfs_dir3_leaf_verify+0xa8/0xe0 [xfs], xfs_dir3_leafn block 0x178
XFS (dm-0): Unmount and run xfs_repair
XFS (dm-0): First 128 bytes of corrupted metadata buffer:
00000000e80f1917: 00 80 00 0b 00 80 00 07 3d ff 00 00 00 00 00 00 ........=.......
000000009604c005: 00 00 00 00 00 00 01 a0 00 00 00 00 00 00 00 00 ................
000000006b6fb2bf: e4 44 e3 97 b5 64 44 41 8b 84 60 0e 50 43 d9 bf .D...dDA..`.PC..
00000000678978a2: 00 00 00 00 00 00 00 83 01 73 00 93 00 00 00 00 .........s......
00000000b28b247c: 99 29 1d 38 00 00 00 00 99 29 1d 40 00 00 00 00 .).8.....).@....
000000002b2a662c: 99 29 1d 48 00 00 00 00 99 49 11 00 00 00 00 00 .).H.....I......
00000000ea2ffbb8: 99 49 11 08 00 00 45 25 99 49 11 10 00 00 48 fe .I....E%.I....H.
0000000069e86440: 99 49 11 18 00 00 4c 6b 99 49 11 20 00 00 4d 97 .I....Lk.I. ..M.
XFS (dm-0): xfs_do_force_shutdown(0x8) called from line 1423 of file fs/xfs/xfs_buf.c. Return address = 00000000c0ff63c1
XFS (dm-0): Corruption of in-memory data detected. Shutting down filesystem
XFS (dm-0): Please umount the filesystem and rectify the problem(s)
>>From the log above, we know xfs_buf->b_no is 0x178, but the block's hdr record
its blkno is 0x1a0.
Fixes: 24df33b45e ("xfs: add CRC checking to dir2 leaf blocks")
Signed-off-by: Zhang Tianci <zhangtianci.1997@bytedance.com>
Suggested-by: Dave Chinner <david@fromorbit.com>
Reviewed-by: "Darrick J. Wong" <djwong@kernel.org>
Signed-off-by: Chandan Babu R <chandanbabu@kernel.org>
Signed-off-by: Catherine Hoang <catherine.hoang@oracle.com>
Acked-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e6af9c98cb upstream.
In the case of returning -ENOSPC, ensure logflagsp is initialized by 0.
Otherwise the caller __xfs_bunmapi will set uninitialized illegal
tmp_logflags value into xfs log, which might cause unpredictable error
in the log recovery procedure.
Also, remove the flags variable and set the *logflagsp directly, so that
the code should be more robust in the long run.
Fixes: 1b24b633aa ("xfs: move some more code into xfs_bmap_del_extent_real")
Signed-off-by: Jiachen Zhang <zhangjiachen.jaycee@bytedance.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: "Darrick J. Wong" <djwong@kernel.org>
Signed-off-by: Chandan Babu R <chandanbabu@kernel.org>
Signed-off-by: Catherine Hoang <catherine.hoang@oracle.com>
Acked-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7823921887 upstream.
During growfs, if new ag in memory has been initialized, however
sb_agcount has not been updated, if an error occurs at this time it
will cause perag leaks as follows, these new AGs will not been freed
during umount , because of these new AGs are not visible(that is
included in mp->m_sb.sb_agcount).
unreferenced object 0xffff88810be40200 (size 512):
comm "xfs_growfs", pid 857, jiffies 4294909093
hex dump (first 32 bytes):
00 c0 c1 05 81 88 ff ff 04 00 00 00 00 00 00 00 ................
01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace (crc 381741e2):
[<ffffffff8191aef6>] __kmalloc+0x386/0x4f0
[<ffffffff82553e65>] kmem_alloc+0xb5/0x2f0
[<ffffffff8238dac5>] xfs_initialize_perag+0xc5/0x810
[<ffffffff824f679c>] xfs_growfs_data+0x9bc/0xbc0
[<ffffffff8250b90e>] xfs_file_ioctl+0x5fe/0x14d0
[<ffffffff81aa5194>] __x64_sys_ioctl+0x144/0x1c0
[<ffffffff83c3d81f>] do_syscall_64+0x3f/0xe0
[<ffffffff83e00087>] entry_SYSCALL_64_after_hwframe+0x62/0x6a
unreferenced object 0xffff88810be40800 (size 512):
comm "xfs_growfs", pid 857, jiffies 4294909093
hex dump (first 32 bytes):
20 00 00 00 00 00 00 00 57 ef be dc 00 00 00 00 .......W.......
10 08 e4 0b 81 88 ff ff 10 08 e4 0b 81 88 ff ff ................
backtrace (crc bde50e2d):
[<ffffffff8191b43a>] __kmalloc_node+0x3da/0x540
[<ffffffff81814489>] kvmalloc_node+0x99/0x160
[<ffffffff8286acff>] bucket_table_alloc.isra.0+0x5f/0x400
[<ffffffff8286bdc5>] rhashtable_init+0x405/0x760
[<ffffffff8238dda3>] xfs_initialize_perag+0x3a3/0x810
[<ffffffff824f679c>] xfs_growfs_data+0x9bc/0xbc0
[<ffffffff8250b90e>] xfs_file_ioctl+0x5fe/0x14d0
[<ffffffff81aa5194>] __x64_sys_ioctl+0x144/0x1c0
[<ffffffff83c3d81f>] do_syscall_64+0x3f/0xe0
[<ffffffff83e00087>] entry_SYSCALL_64_after_hwframe+0x62/0x6a
Factor out xfs_free_unused_perag_range() from xfs_initialize_perag(),
used for freeing unused perag within a specified range in error handling,
included in the error path of the growfs failure.
Fixes: 1c1c6ebcf5 ("xfs: Replace per-ag array with a radix tree")
Signed-off-by: Long Li <leo.lilong@huawei.com>
Reviewed-by: "Darrick J. Wong" <djwong@kernel.org>
Signed-off-by: Chandan Babu R <chandanbabu@kernel.org>
Signed-off-by: Catherine Hoang <catherine.hoang@oracle.com>
Acked-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07afd3173d upstream.
Take mp->m_perag_lock for deletions from the perag radix tree in
xfs_initialize_perag to prevent racing with tagging operations.
Lookups are fine - they are RCU protected so already deal with the
tree changing shape underneath the lookup - but tagging operations
require the tree to be stable while the tags are propagated back up
to the root.
Right now there's nothing stopping radix tree tagging from operating
while a growfs operation is progress and adding/removing new entries
into the radix tree.
Hence we can have traversals that require a stable tree occurring at
the same time we are removing unused entries from the radix tree which
causes the shape of the tree to change.
Likely this hasn't caused a problem in the past because we are only
doing append addition and removal so the active AG part of the tree
is not changing shape, but that doesn't mean it is safe. Just making
the radix tree modifications serialise against each other is obviously
correct.
Signed-off-by: Long Li <leo.lilong@huawei.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: "Darrick J. Wong" <djwong@kernel.org>
Signed-off-by: Chandan Babu R <chandanbabu@kernel.org>
Signed-off-by: Catherine Hoang <catherine.hoang@oracle.com>
Acked-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 84712492e6 upstream.
Although xfs_growfs_data() doesn't call xfs_growfs_data_private()
if in->newblocks == mp->m_sb.sb_dblocks, xfs_growfs_data_private()
further massages the new block count so that we don't i.e. try
to create a too-small new AG.
This may lead to a delta of "0" in xfs_growfs_data_private(), so
we end up in the shrink case and emit the EXPERIMENTAL warning
even if we're not changing anything at all.
Fix this by returning straightaway if the block delta is zero.
(nb: in older kernels, the result of entering the shrink case
with delta == 0 may actually let an -ENOSPC escape to userspace,
which is confusing for users.)
Fixes: fb2fc17201 ("xfs: support shrinking unused space in the last AG")
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: "Darrick J. Wong" <djwong@kernel.org>
Signed-off-by: Chandan Babu R <chandanbabu@kernel.org>
Signed-off-by: Catherine Hoang <catherine.hoang@oracle.com>
Acked-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0573676fdd upstream.
Alexander Potapenko report that KMSAN was issuing these warnings:
kmalloc-ed xlog buffer of size 512 : ffff88802fc26200
kmalloc-ed xlog buffer of size 368 : ffff88802fc24a00
kmalloc-ed xlog buffer of size 648 : ffff88802b631000
kmalloc-ed xlog buffer of size 648 : ffff88802b632800
kmalloc-ed xlog buffer of size 648 : ffff88802b631c00
xlog_write_iovec: copying 12 bytes from ffff888017ddbbd8 to ffff88802c300400
xlog_write_iovec: copying 28 bytes from ffff888017ddbbe4 to ffff88802c30040c
xlog_write_iovec: copying 68 bytes from ffff88802fc26274 to ffff88802c300428
xlog_write_iovec: copying 188 bytes from ffff88802fc262bc to ffff88802c30046c
=====================================================
BUG: KMSAN: uninit-value in xlog_write_iovec fs/xfs/xfs_log.c:2227
BUG: KMSAN: uninit-value in xlog_write_full fs/xfs/xfs_log.c:2263
BUG: KMSAN: uninit-value in xlog_write+0x1fac/0x2600 fs/xfs/xfs_log.c:2532
xlog_write_iovec fs/xfs/xfs_log.c:2227
xlog_write_full fs/xfs/xfs_log.c:2263
xlog_write+0x1fac/0x2600 fs/xfs/xfs_log.c:2532
xlog_cil_write_chain fs/xfs/xfs_log_cil.c:918
xlog_cil_push_work+0x30f2/0x44e0 fs/xfs/xfs_log_cil.c:1263
process_one_work kernel/workqueue.c:2630
process_scheduled_works+0x1188/0x1e30 kernel/workqueue.c:2703
worker_thread+0xee5/0x14f0 kernel/workqueue.c:2784
kthread+0x391/0x500 kernel/kthread.c:388
ret_from_fork+0x66/0x80 arch/x86/kernel/process.c:147
ret_from_fork_asm+0x11/0x20 arch/x86/entry/entry_64.S:242
Uninit was created at:
slab_post_alloc_hook+0x101/0xac0 mm/slab.h:768
slab_alloc_node mm/slub.c:3482
__kmem_cache_alloc_node+0x612/0xae0 mm/slub.c:3521
__do_kmalloc_node mm/slab_common.c:1006
__kmalloc+0x11a/0x410 mm/slab_common.c:1020
kmalloc ./include/linux/slab.h:604
xlog_kvmalloc fs/xfs/xfs_log_priv.h:704
xlog_cil_alloc_shadow_bufs fs/xfs/xfs_log_cil.c:343
xlog_cil_commit+0x487/0x4dc0 fs/xfs/xfs_log_cil.c:1574
__xfs_trans_commit+0x8df/0x1930 fs/xfs/xfs_trans.c:1017
xfs_trans_commit+0x30/0x40 fs/xfs/xfs_trans.c:1061
xfs_create+0x15af/0x2150 fs/xfs/xfs_inode.c:1076
xfs_generic_create+0x4cd/0x1550 fs/xfs/xfs_iops.c:199
xfs_vn_create+0x4a/0x60 fs/xfs/xfs_iops.c:275
lookup_open fs/namei.c:3477
open_last_lookups fs/namei.c:3546
path_openat+0x29ac/0x6180 fs/namei.c:3776
do_filp_open+0x24d/0x680 fs/namei.c:3809
do_sys_openat2+0x1bc/0x330 fs/open.c:1440
do_sys_open fs/open.c:1455
__do_sys_openat fs/open.c:1471
__se_sys_openat fs/open.c:1466
__x64_sys_openat+0x253/0x330 fs/open.c:1466
do_syscall_x64 arch/x86/entry/common.c:51
do_syscall_64+0x4f/0x140 arch/x86/entry/common.c:82
entry_SYSCALL_64_after_hwframe+0x63/0x6b arch/x86/entry/entry_64.S:120
Bytes 112-115 of 188 are uninitialized
Memory access of size 188 starts at ffff88802fc262bc
This is caused by the struct xfs_log_dinode not having the di_crc
field initialised. Log recovery never uses this field (it is only
present these days for on-disk format compatibility reasons) and so
it's value is never checked so nothing in XFS has caught this.
Further, none of the uninitialised memory access warning tools have
caught this (despite catching other uninit memory accesses in the
struct xfs_log_dinode back in 2017!) until recently. Alexander
annotated the XFS code to get the dump of the actual bytes that were
detected as uninitialised, and from that report it took me about 30s
to realise what the issue was.
The issue was introduced back in 2016 and every inode that is logged
fails to initialise this field. This is no actual bad behaviour
caused by this issue - I find it hard to even classify it as a
bug...
Reported-and-tested-by: Alexander Potapenko <glider@google.com>
Fixes: f8d55aa052 ("xfs: introduce inode log format object")
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: "Darrick J. Wong" <djwong@kernel.org>
Signed-off-by: Chandan Babu R <chandanbabu@kernel.org>
Signed-off-by: Catherine Hoang <catherine.hoang@oracle.com>
Acked-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 13ae04d8d4 upstream.
While stress-testing online repair of btrees, I noticed periodic
assertion failures from the buffer cache about buffers with incorrect
DELWRI_Q state. Looking further, I observed this race between the AIL
trying to write out a btree block and repair zapping a btree block after
the fact:
AIL: Repair0:
pin buffer X
delwri_queue:
set DELWRI_Q
add to delwri list
stale buf X:
clear DELWRI_Q
does not clear b_list
free space X
commit
delwri_submit # oops
Worse yet, I discovered that running the same repair over and over in a
tight loop can result in a second race that cause data integrity
problems with the repair:
AIL: Repair0: Repair1:
pin buffer X
delwri_queue:
set DELWRI_Q
add to delwri list
stale buf X:
clear DELWRI_Q
does not clear b_list
free space X
commit
find free space X
get buffer
rewrite buffer
delwri_queue:
set DELWRI_Q
already on a list, do not add
commit
BAD: committed tree root before all blocks written
delwri_submit # too late now
I traced this to my own misunderstanding of how the delwri lists work,
particularly with regards to the AIL's buffer list. If a buffer is
logged and committed, the buffer can end up on that AIL buffer list. If
btree repairs are run twice in rapid succession, it's possible that the
first repair will invalidate the buffer and free it before the next time
the AIL wakes up. Marking the buffer stale clears DELWRI_Q from the
buffer state without removing the buffer from its delwri list. The
buffer doesn't know which list it's on, so it cannot know which lock to
take to protect the list for a removal.
If the second repair allocates the same block, it will then recycle the
buffer to start writing the new btree block. Meanwhile, if the AIL
wakes up and walks the buffer list, it will ignore the buffer because it
can't lock it, and go back to sleep.
When the second repair calls delwri_queue to put the buffer on the
list of buffers to write before committing the new btree, it will set
DELWRI_Q again, but since the buffer hasn't been removed from the AIL's
buffer list, it won't add it to the bulkload buffer's list.
This is incorrect, because the bulkload caller relies on delwri_submit
to ensure that all the buffers have been sent to disk /before/
committing the new btree root pointer. This ordering requirement is
required for data consistency.
Worse, the AIL won't clear DELWRI_Q from the buffer when it does finally
drop it, so the next thread to walk through the btree will trip over a
debug assertion on that flag.
To fix this, create a new function that waits for the buffer to be
removed from any other delwri lists before adding the buffer to the
caller's delwri list. By waiting for the buffer to clear both the
delwri list and any potential delwri wait list, we can be sure that
repair will initiate writes of all buffers and report all write errors
back to userspace instead of committing the new structure.
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Catherine Hoang <catherine.hoang@oracle.com>
Acked-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c0e37f07d2 upstream.
Overall, this function tries to find and invalidate all buffers for a
given extent of space on the data device. The inner for loop in this
function tries to find all xfs_bufs for a given daddr. The lengths of
all possible cached buffers range from 1 fsblock to the largest needed
to contain a 64k xattr value (~17fsb). The scan is capped to avoid
looking at anything buffer going past the given extent.
Unfortunately, the loop continuation test is wrong -- max_fsbs is the
largest size we want to scan, not one past that. Put another way, this
loop is actually 1-indexed, not 0-indexed. Therefore, the continuation
test should use <=, not <.
As a result, online repairs of btree blocks fails to stale any buffers
for btrees that are being torn down, which causes later assertions in
the buffer cache when another thread creates a different-sized buffer.
This happens in xfs/709 when allocating an inode cluster buffer:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 3346128 at fs/xfs/xfs_message.c:104 assfail+0x3a/0x40 [xfs]
CPU: 0 PID: 3346128 Comm: fsstress Not tainted 6.7.0-rc4-djwx #rc4
RIP: 0010:assfail+0x3a/0x40 [xfs]
Call Trace:
<TASK>
_xfs_buf_obj_cmp+0x4a/0x50
xfs_buf_get_map+0x191/0xba0
xfs_trans_get_buf_map+0x136/0x280
xfs_ialloc_inode_init+0x186/0x340
xfs_ialloc_ag_alloc+0x254/0x720
xfs_dialloc+0x21f/0x870
xfs_create_tmpfile+0x1a9/0x2f0
xfs_rename+0x369/0xfd0
xfs_vn_rename+0xfa/0x170
vfs_rename+0x5fb/0xc30
do_renameat2+0x52d/0x6e0
__x64_sys_renameat2+0x4b/0x60
do_syscall_64+0x3b/0xe0
entry_SYSCALL_64_after_hwframe+0x46/0x4e
A later refactoring patch in the online repair series fixed this by
accident, which is why I didn't notice this until I started testing only
the patches that are likely to end up in 6.8.
Fixes: 1c7ce115e5 ("xfs: reap large AG metadata extents when possible")
Signed-off-by: "Darrick J. Wong" <djwong@kernel.org>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Chandan Babu R <chandanbabu@kernel.org>
Signed-off-by: Catherine Hoang <catherine.hoang@oracle.com>
Acked-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 578bd4ce71 upstream.
While playing with growfs to create a 20TB realtime section on a
filesystem that didn't previously have an rt section, I noticed that
growfs would occasionally shut down the log due to a transaction
reservation overflow.
xfs_calc_growrtfree_reservation uses the current size of the realtime
summary file (m_rsumsize) to compute the transaction reservation for a
growrtfree transaction. The reservations are computed at mount time,
which means that m_rsumsize is zero when growfs starts "freeing" the new
realtime extents into the rt volume. As a result, the transaction is
undersized and fails.
Fix this by recomputing the transaction reservations every time we
change m_rsumsize.
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Catherine Hoang <catherine.hoang@oracle.com>
Acked-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c8ecd1cfd upstream.
Remove these unused fields since nobody uses them. They should have
been removed years ago in a different cleanup series from Christoph
Hellwig.
Fixes: daf83964a3 ("xfs: move the per-fork nextents fields into struct xfs_ifork")
Fixes: f7e67b20ec ("xfs: move the fork format fields into struct xfs_ifork")
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Catherine Hoang <catherine.hoang@oracle.com>
Acked-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f113c2739 upstream.
When scrub is trying to iget an inode, ensure that it won't end up
deadlocked on a cycle in the inode btree by using an empty transaction
to store all the buffers.
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Catherine Hoang <catherine.hoang@oracle.com>
Acked-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e14293803f upstream.
[backport: resolve merge conflicts due to refactoring rtbitmap/summary
macros and accessors]
Don't allow realtime volumes that are less than one rt extent long.
This has been broken across 4 LTS kernels with nobody noticing, so let's
just disable it.
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Catherine Hoang <catherine.hoang@oracle.com>
Acked-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cf8f0e6c14 upstream.
It's quite reasonable that some customer somewhere will want to
configure a realtime volume with more than 2^32 extents. If they try to
do this, the highbit32() call will truncate the upper bits of the
xfs_rtbxlen_t and produce the wrong value for rextslog. This in turn
causes the rsumlevels to be wrong, which results in a realtime summary
file that is the wrong length. Fix that.
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Catherine Hoang <catherine.hoang@oracle.com>
Acked-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a6a38f309a upstream.
[backport: resolve merge conflicts due to refactoring rtbitmap/summary
macros and accessors]
There's a weird discrepancy in xfsprogs dating back to the creation of
the Linux port -- if there are zero rt extents, mkfs will set
sb_rextents and sb_rextslog both to zero:
sbp->sb_rextslog =
(uint8_t)(rtextents ?
libxfs_highbit32((unsigned int)rtextents) : 0);
However, that's not the check that xfs_repair uses for nonzero rtblocks:
if (sb->sb_rextslog !=
libxfs_highbit32((unsigned int)sb->sb_rextents))
The difference here is that xfs_highbit32 returns -1 if its argument is
zero. Unfortunately, this means that in the weird corner case of a
realtime volume shorter than 1 rt extent, xfs_repair will immediately
flag a freshly formatted filesystem as corrupt. Because mkfs has been
writing ondisk artifacts like this for decades, we have to accept that
as "correct". TBH, zero rextslog for zero rtextents makes more sense to
me anyway.
Regrettably, the superblock verifier checks created in commit copied
xfs_repair even though mkfs has been writing out such filesystems for
ages. Fix the superblock verifier to accept what mkfs spits out; the
userspace version of this patch will have to fix xfs_repair as well.
Note that the new helper leaves the zeroday bug where the upper 32 bits
of sb_rextents is ripped off and fed to highbit32. This leads to a
seriously undersized rt summary file, which immediately breaks mkfs:
$ hugedisk.sh foo /dev/sdc $(( 0x100000080 * 4096))B
$ /sbin/mkfs.xfs -f /dev/sda -m rmapbt=0,reflink=0 -r rtdev=/dev/mapper/foo
meta-data=/dev/sda isize=512 agcount=4, agsize=1298176 blks
= sectsz=512 attr=2, projid32bit=1
= crc=1 finobt=1, sparse=1, rmapbt=0
= reflink=0 bigtime=1 inobtcount=1 nrext64=1
data = bsize=4096 blocks=5192704, imaxpct=25
= sunit=0 swidth=0 blks
naming =version 2 bsize=4096 ascii-ci=0, ftype=1
log =internal log bsize=4096 blocks=16384, version=2
= sectsz=512 sunit=0 blks, lazy-count=1
realtime =/dev/mapper/foo extsz=4096 blocks=4294967424, rtextents=4294967424
Discarding blocks...Done.
mkfs.xfs: Error initializing the realtime space [117 - Structure needs cleaning]
The next patch will drop support for rt volumes with fewer than 1 or
more than 2^32-1 rt extents, since they've clearly been broken forever.
Fixes: f8e566c0f5 ("xfs: validate the realtime geometry in xfs_validate_sb_common")
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Catherine Hoang <catherine.hoang@oracle.com>
Acked-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit deb4cd8ba8 upstream.
Now that we pass the xfs_defer_pending object into the intent item
recovery functions, we know exactly when ownership of the sole refcount
passes from the recovery context to the intent done item. At that
point, we need to null out dfp_intent so that the recovery mechanism
won't release it. This should fix the UAF problem reported by Long Li.
Note that we still want to recreate the full deferred work state. That
will be addressed in the next patches.
Fixes: 2e76f188fd ("xfs: cancel intents immediately if process_intents fails")
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Catherine Hoang <catherine.hoang@oracle.com>
Acked-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a050acdfa8 upstream.
Now that log intent item recovery recreates the xfs_defer_pending state,
we should pass that into the ->iop_recover routines so that the intent
item can finish the recreation work.
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Catherine Hoang <catherine.hoang@oracle.com>
Acked-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 03f7767c9f upstream.
One thing I never quite got around to doing is porting the log intent
item recovery code to reconstruct the deferred pending work state. As a
result, each intent item open codes xfs_defer_finish_one in its recovery
method, because that's what the EFI code did before xfs_defer.c even
existed.
This is a gross thing to have left unfixed -- if an EFI cannot proceed
due to busy extents, we end up creating separate new EFIs for each
unfinished work item, which is a change in behavior from what runtime
would have done.
Worse yet, Long Li pointed out that there's a UAF in the recovery code.
The ->commit_pass2 function adds the intent item to the AIL and drops
the refcount. The one remaining refcount is now owned by the recovery
mechanism (aka the log intent items in the AIL) with the intent of
giving the refcount to the intent done item in the ->iop_recover
function.
However, if something fails later in recovery, xlog_recover_finish will
walk the recovered intent items in the AIL and release them. If the CIL
hasn't been pushed before that point (which is possible since we don't
force the log until later) then the intent done release will try to free
its associated intent, which has already been freed.
This patch starts to address this mess by having the ->commit_pass2
functions recreate the xfs_defer_pending state. The next few patches
will fix the recovery functions.
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Catherine Hoang <catherine.hoang@oracle.com>
Acked-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07bcbdf020 upstream.
If recovery finds an xattr log intent item calling for the removal of an
attribute and the file doesn't even have an attr fork, we know that the
removal is trivially complete. However, we can't just exit the recovery
function without doing something about the recovered log intent item --
it's still on the AIL, and not logging an attrd item means it stays
there forever.
This has likely not been seen in practice because few people use LARP
and the runtime code won't log the attri for a no-attrfork removexattr
operation. But let's fix this anyway.
Also we shouldn't really be testing the attr fork presence until we've
taken the ILOCK, though this doesn't matter much in recovery, which is
single threaded.
Fixes: fdaf1bb3ca ("xfs: ATTR_REPLACE algorithm with LARP enabled needs rework")
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Catherine Hoang <catherine.hoang@oracle.com>
Acked-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 944df75958 upstream.
[backport: resolve merge conflict due to missing xfs_rtxlen_t type]
minlen is the lower bound on the extent length that the caller can
accept, and maxlen is at this point the maximal available length.
This means a minlen extent is perfectly fine to use, so do it. This
matches the equivalent logic in xfs_rtallocate_extent_exact that also
accepts a minlen sized extent.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: "Darrick J. Wong" <djwong@kernel.org>
Signed-off-by: Chandan Babu R <chandanbabu@kernel.org>
Signed-off-by: Catherine Hoang <catherine.hoang@oracle.com>
Acked-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f29c3e745d upstream.
XFS uses xfs_rtblock_t for many different uses, which makes it much more
difficult to perform a unit analysis on the codebase. One of these
(ab)uses is when we need to store the length of a free space extent as
stored in the realtime bitmap. Because there can be up to 2^64 realtime
extents in a filesystem, we need a new type that is larger than
xfs_rtxlen_t for callers that are querying the bitmap directly. This
means scrub and growfs.
Create this type as "xfs_rtbxlen_t" and use it to store 64-bit rtx
lengths. 'b' stands for 'bitmap' or 'big'; reader's choice.
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Catherine Hoang <catherine.hoang@oracle.com>
Acked-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 605d7c0b05 upstream.
Clear bit 8 of REG_SYS_STATUS1 after MAC power on.
Without this, some RTL8821CU and RTL8811CU cannot connect to any
network:
Feb 19 13:33:11 ideapad2 kernel: wlp3s0f3u2: send auth to
90:55:de:__:__:__ (try 1/3)
Feb 19 13:33:13 ideapad2 kernel: wlp3s0f3u2: send auth to
90:55:de:__:__:__ (try 2/3)
Feb 19 13:33:14 ideapad2 kernel: wlp3s0f3u2: send auth to
90:55:de:__:__:__ (try 3/3)
Feb 19 13:33:15 ideapad2 kernel: wlp3s0f3u2: authentication with
90:55:de:__:__:__ timed out
The RTL8822CU and RTL8822BU out-of-tree drivers do this as well, so do
it for all three types of chips.
Tested with RTL8811CU (Tenda U9 V2.0).
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/aeeefad9-27c8-4506-a510-ef9a9a8731a4@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cefcd4fe2e upstream.
Normally, the EFI stub calls into the EFI boot services using the stack
that was live when the stub was entered. According to the UEFI spec,
this stack needs to be at least 128k in size - this might seem large but
all asynchronous processing and event handling in EFI runs from the same
stack and so quite a lot of space may be used in practice.
In mixed mode, the situation is a bit different: the bootloader calls
the 32-bit EFI stub entry point, which calls the decompressor's 32-bit
entry point, where the boot stack is set up, using a fixed allocation
of 16k. This stack is still in use when the EFI stub is started in
64-bit mode, and so all calls back into the EFI firmware will be using
the decompressor's limited boot stack.
Due to the placement of the boot stack right after the boot heap, any
stack overruns have gone unnoticed. However, commit
5c4feadb00 ("x86/decompressor: Move global symbol references to C code")
moved the definition of the boot heap into C code, and now the boot
stack is placed right at the base of BSS, where any overruns will
corrupt the end of the .data section.
While it would be possible to work around this by increasing the size of
the boot stack, doing so would affect all x86 systems, and mixed mode
systems are a tiny (and shrinking) fraction of the x86 installed base.
So instead, record the firmware stack pointer value when entering from
the 32-bit firmware, and switch to this stack every time a EFI boot
service call is made.
Cc: <stable@kernel.org> # v6.1+
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0b385be4c3 upstream.
The icl+ power well code currently assumes that every AUX power
well maps to an encoder which is using said power well. That is
by no menas guaranteed as we:
- only register encoders for ports declared in the VBT
- combo PHY HDMI-only encoder no longer get an AUX CH since
commit 9856308c94 ("drm/i915: Only populate aux_ch if really needed")
However we have places such as intel_power_domains_sanitize_state()
that blindly traverse all the possible power wells. So these bits
of code may very well encounbter an aux power well with no associated
encoder.
In this particular case the BIOS seems to have left one AUX power
well enabled even though we're dealing with a HDMI only encoder
on a combo PHY. We then proceed to turn off said power well and
explode when we can't find a matching encoder. As a short term fix
we should be able to just skip the PHY related parts of the power
well programming since we know this situation can only happen with
combo PHYs.
Another option might be to go back to always picking an AUX CH for
all encoders. However I'm a bit wary about that since we might in
theory end up conflicting with the VBT AUX CH assignment. Also
that wouldn't help with encoders not declared in the VBT, should
we ever need to poke the corresponding power wells.
Longer term we need to figure out what the actual relationship
is between the PHY vs. AUX CH vs. AUX power well. Currently this
is entirely unclear.
Cc: stable@vger.kernel.org
Fixes: 9856308c94 ("drm/i915: Only populate aux_ch if really needed")
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/10184
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240223203216.15210-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
(cherry picked from commit 6a8c66bf0e)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ceb013b2d9 upstream.
If registering the platform device fails, the lookup table is
removed in the error path. On module removal we would try to
remove the lookup table again. Fix this by setting priv->lookup
only if registering the platform device was successful.
In addition free the memory allocated for the lookup table in
the error path.
Fixes: d308dfbf62 ("i2c: mux/i801: Switch to use descriptor passing")
Cc: stable@vger.kernel.org
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a1c6a8bf4 upstream.
Limit the WiFi PCIe link speed to Gen2 speed (500 MB/s), which is the
speed that the boot firmware has brought up the link at (and that
Windows uses).
This is specifically needed to avoid a large amount of link errors when
restarting the link during boot (but which are currently not reported).
This also appears to fix intermittent failures to download the ath11k
firmware during boot which can be seen when there is a longer delay
between restarting the link and loading the WiFi driver (e.g. when using
full disk encryption).
Fixes: 123b30a756 ("arm64: dts: qcom: sc8280xp-x13s: enable WiFi controller")
Cc: stable@vger.kernel.org # 6.2
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240223152124.20042-8-johan+linaro@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 803de9000f upstream.
Sven reports an infinite loop in __alloc_pages_slowpath() for costly order
__GFP_RETRY_MAYFAIL allocations that are also GFP_NOIO. Such combination
can happen in a suspend/resume context where a GFP_KERNEL allocation can
have __GFP_IO masked out via gfp_allowed_mask.
Quoting Sven:
1. try to do a "costly" allocation (order > PAGE_ALLOC_COSTLY_ORDER)
with __GFP_RETRY_MAYFAIL set.
2. page alloc's __alloc_pages_slowpath tries to get a page from the
freelist. This fails because there is nothing free of that costly
order.
3. page alloc tries to reclaim by calling __alloc_pages_direct_reclaim,
which bails out because a zone is ready to be compacted; it pretends
to have made a single page of progress.
4. page alloc tries to compact, but this always bails out early because
__GFP_IO is not set (it's not passed by the snd allocator, and even
if it were, we are suspending so the __GFP_IO flag would be cleared
anyway).
5. page alloc believes reclaim progress was made (because of the
pretense in item 3) and so it checks whether it should retry
compaction. The compaction retry logic thinks it should try again,
because:
a) reclaim is needed because of the early bail-out in item 4
b) a zonelist is suitable for compaction
6. goto 2. indefinite stall.
(end quote)
The immediate root cause is confusing the COMPACT_SKIPPED returned from
__alloc_pages_direct_compact() (step 4) due to lack of __GFP_IO to be
indicating a lack of order-0 pages, and in step 5 evaluating that in
should_compact_retry() as a reason to retry, before incrementing and
limiting the number of retries. There are however other places that
wrongly assume that compaction can happen while we lack __GFP_IO.
To fix this, introduce gfp_compaction_allowed() to abstract the __GFP_IO
evaluation and switch the open-coded test in try_to_compact_pages() to use
it.
Also use the new helper in:
- compaction_ready(), which will make reclaim not bail out in step 3, so
there's at least one attempt to actually reclaim, even if chances are
small for a costly order
- in_reclaim_compaction() which will make should_continue_reclaim()
return false and we don't over-reclaim unnecessarily
- in __alloc_pages_slowpath() to set a local variable can_compact,
which is then used to avoid retrying reclaim/compaction for costly
allocations (step 5) if we can't compact and also to skip the early
compaction attempt that we do in some cases
Link: https://lkml.kernel.org/r/20240221114357.13655-2-vbabka@suse.cz
Fixes: 3250845d05 ("Revert "mm, oom: prevent premature OOM killer invocation for high order request"")
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Reported-by: Sven van Ashbrook <svenva@chromium.org>
Closes: https://lore.kernel.org/all/CAG-rBihs_xMKb3wrMO1%2B-%2Bp4fowP9oy1pa_OTkfxBzPUVOZF%2Bg@mail.gmail.com/
Tested-by: Karthikeyan Ramasubramanian <kramasub@chromium.org>
Cc: Brian Geffon <bgeffon@google.com>
Cc: Curtis Malainey <cujomalainey@chromium.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b0a5a8a39 upstream.
Since commit bfac19e239 ("fbdev: mx3fb: Remove the driver") backlight
is no longer functional.
The fbdev mx3fb driver used to automatically select
CONFIG_BACKLIGHT_CLASS_DEVICE.
Now that the mx3fb driver has been removed, enable the
CONFIG_BACKLIGHT_CLASS_DEVICE option so that backlight can still work
by default.
Tested on a imx6dl-sabresd board.
Cc: stable@vger.kernel.org
Fixes: bfac19e239 ("fbdev: mx3fb: Remove the driver")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Tested-by: Francesco Dolcini <francesco.dolcini@toradex.com> # Toradex Colibri iMX7
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d9319c27c upstream.
This reverts commit 5c7e105cd1.
As identified by KASAN, the simplification done by the cleanup patch
was not legal.
>From tracing through the code, it can be seen that we're transmitting
from a 4096-byte circular buffer. We copy anywhere from 1-4 bytes from
it each time. The simplification runs into trouble when we get near
the end of the circular buffer. For instance, we might start out with
xmit->tail = 4094 and we want to transfer 4 bytes. With the code
before simplification this was no problem. We'd read buf[4094],
buf[4095], buf[0], and buf[1]. With the new code we'll do a
memcpy(&buf[4094], 4) which reads 2 bytes past the end of the buffer
and then skips transmitting what's at buf[0] and buf[1].
KASAN isn't 100% consistent at reporting this for me, but to be extra
confident in the analysis, I added traces of the tail and tx_bytes and
then wrote a test program:
while true; do
echo -n "abcdefghijklmnopqrstuvwxyz0" > /dev/ttyMSM0
sleep .1
done
I watched the traces over SSH and saw:
qcom_geni_serial_send_chunk_fifo: 4093 4
qcom_geni_serial_send_chunk_fifo: 1 3
Which indicated that one byte should be missing. Sure enough the
output that should have been:
abcdefghijklmnopqrstuvwxyz0
In one case was actually missing a byte:
abcdefghijklmnopqrstuvwyz0
Running "ls -al" on large directories also made the missing bytes
obvious since columns didn't line up.
While the original code may not be the most elegant, we only talking
about copying up to 4 bytes here. Let's just go back to the code that
worked.
Fixes: 5c7e105cd1 ("tty: serial: simplify qcom_geni_serial_send_chunk_fifo()")
Cc: stable <stable@kernel.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240304174952.1.I920a314049b345efd1f69d708e7f74d2213d0b49@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 43066e3222 upstream.
We accidently met the issue that the bash prompt is not shown after the
previous command done and until the next input if there's only one CPU
(In our issue other CPUs are isolated by isolcpus=). Further analysis
shows it's because the port entering runtime suspend even if there's
still pending chars in the buffer and the pending chars will only be
processed in next device resuming. We are using amba-pl011 and the
problematic flow is like below:
Bash kworker
tty_write()
file_tty_write()
n_tty_write()
uart_write()
__uart_start()
pm_runtime_get() // wakeup waker
queue_work()
pm_runtime_work()
rpm_resume()
status = RPM_RESUMING
serial_port_runtime_resume()
port->ops->start_tx()
pl011_tx_chars()
uart_write_wakeup()
[…]
__uart_start()
pm_runtime_get() < 0 // because runtime status = RPM_RESUMING
// later data are not commit to the port driver
status = RPM_ACTIVE
rpm_idle() -> rpm_suspend()
This patch tries to fix this by checking the port busy before entering
runtime suspending. A runtime_suspend callback is added for the port
driver. When entering runtime suspend the callback is invoked, if there's
still pending chars in the buffer then flush the buffer.
Fixes: 84a9582fd2 ("serial: core: Start managing serial controllers to enable runtime PM")
Cc: stable <stable@kernel.org>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Link: https://lore.kernel.org/r/20240226152351.40924-1-yangyicong@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a283d7f179 upstream.
For CMA memory allocation, ownership is assigned to DSP to make it
accessible by the PD running on the DSP. With current implementation
HLOS VM is stored in the channel structure during rpmsg_probe and
this VM is passed to qcom_scm call as the source VM.
The qcom_scm call will overwrite the passed source VM with the next
VM which would cause a problem in case the scm call is again needed.
Adding a local copy of source VM whereever scm call is made to avoid
this problem.
Fixes: 0871561055 ("misc: fastrpc: Add support for audiopd")
Cc: stable <stable@kernel.org>
Signed-off-by: Ekansh Gupta <quic_ekangupt@quicinc.com>
Reviewed-by: Elliot Berman <quic_eberman@quicinc.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20240224114247.85953-2-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ac3e038407 upstream.
When not configured for wakeup lis3lv02d_i2c_suspend() will call
lis3lv02d_poweroff() even if the device has already been turned off
by the runtime-suspend handler and if configured for wakeup and
the device is runtime-suspended at this point then it is not turned
back on to serve as a wakeup source.
Before commit b1b9f7a494 ("misc: lis3lv02d_i2c: Add missing setting
of the reg_ctrl callback"), lis3lv02d_poweroff() failed to disable
the regulators which as a side effect made calling poweroff() twice ok.
Now that poweroff() correctly disables the regulators, doing this twice
triggers a WARN() in the regulator core:
unbalanced disables for regulator-dummy
WARNING: CPU: 1 PID: 92 at drivers/regulator/core.c:2999 _regulator_disable
...
Fix lis3lv02d_i2c_suspend() to not call poweroff() a second time if
already runtime-suspended and add a poweron() call when necessary to
make wakeup work.
lis3lv02d_i2c_resume() has similar issues, with an added weirness that
it always powers on the device if it is runtime suspended, after which
the first runtime-resume will call poweron() again, causing the enabled
count for the regulator to increase by 1 every suspend/resume. These
unbalanced regulator_enable() calls cause the regulator to never
be turned off and trigger the following WARN() on driver unbind:
WARNING: CPU: 1 PID: 1724 at drivers/regulator/core.c:2396 _regulator_put
Fix this by making lis3lv02d_i2c_resume() mirror the new suspend().
Fixes: b1b9f7a494 ("misc: lis3lv02d_i2c: Add missing setting of the reg_ctrl callback")
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Closes: https://lore.kernel.org/regressions/5fc6da74-af0a-4aac-b4d5-a000b39a63a5@molgen.mpg.de/
Cc: stable@vger.kernel.org
Cc: regressions@lists.linux.dev
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de> # Dell XPS 15 7590
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Link: https://lore.kernel.org/r/20240220190035.53402-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 74cb7e0355 upstream.
If the remote uart device is not connected or not enabled after booting
up, the CTS line is high by default. At this time, if we enable the flow
control when opening the device(for example, using “stty -F /dev/ttyLP4
crtscts” command), there will be a pending idle preamble(first writing 0
and then writing 1 to UARTCTRL_TE will queue an idle preamble) that
cannot be sent out, resulting in the uart port fail to close(waiting for
TX empty), so the user space stty will have to wait for a long time or
forever.
This is an LPUART IP bug(idle preamble has higher priority than CTS),
here add a workaround patch to enable TX CTS after enabling UARTCTRL_TE,
so that the idle preamble does not get stuck due to CTS is deasserted.
Fixes: 380c966c09 ("tty: serial: fsl_lpuart: add 32-bit register interface support")
Cc: stable <stable@kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Link: https://lore.kernel.org/r/20240305015706.1050769-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b234c70fef upstream.
Ring expansion checker may incorrectly assume a completely full ring
is empty, missing the need for expansion.
This is due to a special empty ring case where the dequeue ends up
ahead of the enqueue pointer. This is seen when enqueued TRBs fill up
exactly a segment, with enqueue then pointing to the end link TRB.
Once those TRBs are handled the dequeue pointer will follow the link
TRB and end up pointing to the first entry on the next segment, past
the enqueue.
This same enqueue - dequeue condition can be true if a ring is full,
with enqueue ending on that last link TRB before the dequeue pointer
on the next segment.
This can be seen when queuing several ~510 small URBs via usbfs in
one go before a single one is handled (i.e. dequeue not moved from first
entry in segment).
Expand the ring already when enqueue reaches the link TRB before the
dequeue segment, instead of expanding it when enqueue moves into the
dequeue segment.
Reported-by: Chris Yokum <linux-usb@mail.totalphase.com>
Closes: https://lore.kernel.org/all/949223224.833962.1709339266739.JavaMail.zimbra@totalphase.com
Tested-by: Chris Yokum <linux-usb@mail.totalphase.com>
Fixes: f5af638f06 ("xhci: Fix transfer ring expansion size calculation")
Cc: stable@vger.kernel.org # v6.5+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240305132312.955171-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f90ce1e04c upstream.
While connecting to a Linux host with CDC_NCM_NTB_DEF_SIZE_TX
set to 65536, it has been observed that we receive short packets,
which come at interval of 5-10 seconds sometimes and have block
length zero but still contain 1-2 valid datagrams present.
According to the NCM spec:
"If wBlockLength = 0x0000, the block is terminated by a
short packet. In this case, the USB transfer must still
be shorter than dwNtbInMaxSize or dwNtbOutMaxSize. If
exactly dwNtbInMaxSize or dwNtbOutMaxSize bytes are sent,
and the size is a multiple of wMaxPacketSize for the
given pipe, then no ZLP shall be sent.
wBlockLength= 0x0000 must be used with extreme care, because
of the possibility that the host and device may get out of
sync, and because of test issues.
wBlockLength = 0x0000 allows the sender to reduce latency by
starting to send a very large NTB, and then shortening it when
the sender discovers that there’s not sufficient data to justify
sending a large NTB"
However, there is a potential issue with the current implementation,
as it checks for the occurrence of multiple NTBs in a single
giveback by verifying if the leftover bytes to be processed is zero
or not. If the block length reads zero, we would process the same
NTB infintely because the leftover bytes is never zero and it leads
to a crash. Fix this by bailing out if block length reads zero.
Cc: stable@vger.kernel.org
Fixes: 427694cfaa ("usb: gadget: ncm: Handle decoding of multiple NTB's in unwrap call")
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20240228115441.2105585-1-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 165376f6b2 upstream.
The DisplayPort driver's sysfs nodes may be present to the userspace before
typec_altmode_set_drvdata() completes in dp_altmode_probe. This means that
a sysfs read can trigger a NULL pointer error by deferencing dp->hpd in
hpd_show or dp->lock in pin_assignment_show, as dev_get_drvdata() returns
NULL in those cases.
Remove manual sysfs node creation in favor of adding attribute group as
default for devices bound to the driver. The ATTRIBUTE_GROUPS() macro is
not used here otherwise the path to the sysfs nodes is no longer compliant
with the ABI.
Fixes: 0e3bb7d689 ("usb: typec: Add driver for DisplayPort alternate mode")
Cc: stable@vger.kernel.org
Signed-off-by: RD Babiera <rdbabiera@google.com>
Link: https://lore.kernel.org/r/20240229001101.3889432-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 672448ccf9 upstream.
When about to transmit the function imx_uart_start_tx is called and in
some RS485 configurations this function will call imx_uart_stop_rx. The
problem is that imx_uart_stop_rx will enable loopback in order to
release the RS485 bus, but when loopback is enabled transmitted data
will just be looped to RX.
This patch fixes the above problem by not enabling loopback when about
to transmit.
This driver now works well when used for RS485 half duplex master
configurations.
Fixes: 79d0224f6b ("tty: serial: imx: Handle RS485 DE signal active high")
Cc: stable <stable@kernel.org>
Signed-off-by: Rickard x Andersson <rickaran@axis.com>
Tested-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Link: https://lore.kernel.org/r/20240221115304.509811-1-rickaran@axis.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e5d7c19165 upstream.
The .release() function does not get called until all readers of a file
descriptor are finished.
If a thread is blocked on reading a file descriptor in ring_buffer_wait(),
and another thread closes the file descriptor, it will not wake up the
other thread as ring_buffer_wake_waiters() is called by .release(), and
that will not get called until the .read() is finished.
The issue originally showed up in trace-cmd, but the readers are actually
other processes with their own file descriptors. So calling close() would wake
up the other tasks because they are blocked on another descriptor then the
one that was closed(). But there's other wake ups that solve that issue.
When a thread is blocked on a read, it can still hang even when another
thread closed its descriptor.
This is what the .flush() callback is for. Have the .flush() wake up the
readers.
Link: https://lore.kernel.org/linux-trace-kernel/20240308202432.107909457@goodmis.org
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linke li <lilinke99@qq.com>
Cc: Rabin Vincent <rabin@rab.in>
Fixes: f3ddb74ad0 ("tracing: Wake up ring buffer waiters on closing of the file")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5abf6dceb0 upstream.
The DebugSwap feature of SEV-ES provides a way for confidential guests to use
data breakpoints. However, because the status of the DebugSwap feature is
recorded in the VMSA, enabling it by default invalidates the attestation
signatures. In 6.10 we will introduce a new API to create SEV VMs that
will allow enabling DebugSwap based on what the user tells KVM to do.
Contextually, we will change the legacy KVM_SEV_ES_INIT API to never
enable DebugSwap.
For compatibility with kernels that pre-date the introduction of DebugSwap,
as well as with those where KVM_SEV_ES_INIT will never enable it, do not enable
the feature by default. If anybody wants to use it, for now they can enable
the sev_es_debug_swap_enabled module parameter, but this will result in a
warning.
Fixes: d1f85fbe83 ("KVM: SEV: Enable data breakpoints in SEV-ES")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ef1d8c1dd upstream.
Do the cache flush of converted pages in svm_register_enc_region() before
dropping kvm->lock to fix use-after-free issues where region and/or its
array of pages could be freed by a different task, e.g. if userspace has
__unregister_enc_region_locked() already queued up for the region.
Note, the "obvious" alternative of using local variables doesn't fully
resolve the bug, as region->pages is also dynamically allocated. I.e. the
region structure itself would be fine, but region->pages could be freed.
Flushing multiple pages under kvm->lock is unfortunate, but the entire
flow is a rare slow path, and the manual flush is only needed on CPUs that
lack coherency for encrypted memory.
Fixes: 19a23da539 ("Fix unsynchronized access to sev members through svm_register_enc_region")
Reported-by: Gabe Kirkpatrick <gkirkpatrick@google.com>
Cc: Josh Eads <josheads@google.com>
Cc: Peter Gonda <pgonda@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20240217013430.2079561-1-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 910c57dfa4 upstream.
When emulating an atomic access on behalf of the guest, mark the target
gfn dirty if the CMPXCHG by KVM is attempted and doesn't fault. This
fixes a bug where KVM effectively corrupts guest memory during live
migration by writing to guest memory without informing userspace that the
page is dirty.
Marking the page dirty got unintentionally dropped when KVM's emulated
CMPXCHG was converted to do a user access. Before that, KVM explicitly
mapped the guest page into kernel memory, and marked the page dirty during
the unmap phase.
Mark the page dirty even if the CMPXCHG fails, as the old data is written
back on failure, i.e. the page is still written. The value written is
guaranteed to be the same because the operation is atomic, but KVM's ABI
is that all writes are dirty logged regardless of the value written. And
more importantly, that's what KVM did before the buggy commit.
Huge kudos to the folks on the Cc list (and many others), who did all the
actual work of triaging and debugging.
Fixes: 1c2361f667 ("KVM: x86: Use __try_cmpxchg_user() to emulate atomic accesses")
Cc: stable@vger.kernel.org
Cc: David Matlack <dmatlack@google.com>
Cc: Pasha Tatashin <tatashin@google.com>
Cc: Michael Krebs <mkrebs@google.com>
base-commit: 6769ea8da8a93ed4630f1ce64df6aafcaabfce64
Reviewed-by: Jim Mattson <jmattson@google.com>
Link: https://lore.kernel.org/r/20240215010004.1456078-2-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 575801663c upstream.
Commit 5a95f1ded2 ("firewire: ohci: use devres for requested IRQ")
also removed the call to free_irq() in pci_remove(), leading to a
leftover irq of devm_request_irq() at pci_disable_msi() in pci_remove()
when unbinding the driver from the device
remove_proc_entry: removing non-empty directory 'irq/136', leaking at
least 'firewire_ohci'
Call Trace:
? remove_proc_entry+0x19c/0x1c0
? __warn+0x81/0x130
? remove_proc_entry+0x19c/0x1c0
? report_bug+0x171/0x1a0
? console_unlock+0x78/0x120
? handle_bug+0x3c/0x80
? exc_invalid_op+0x17/0x70
? asm_exc_invalid_op+0x1a/0x20
? remove_proc_entry+0x19c/0x1c0
unregister_irq_proc+0xf4/0x120
free_desc+0x3d/0xe0
? kfree+0x29f/0x2f0
irq_free_descs+0x47/0x70
msi_domain_free_locked.part.0+0x19d/0x1d0
msi_domain_free_irqs_all_locked+0x81/0xc0
pci_free_msi_irqs+0x12/0x40
pci_disable_msi+0x4c/0x60
pci_remove+0x9d/0xc0 [firewire_ohci
01b483699bebf9cb07a3d69df0aa2bee71db1b26]
pci_device_remove+0x37/0xa0
device_release_driver_internal+0x19f/0x200
unbind_store+0xa1/0xb0
remove irq with devm_free_irq() before pci_disable_msi()
also remove it in fail_msi: of pci_probe() as this would lead to
an identical leak
Cc: stable@vger.kernel.org
Fixes: 5a95f1ded2 ("firewire: ohci: use devres for requested IRQ")
Signed-off-by: Edmund Raile <edmund.raile@proton.me>
Link: https://lore.kernel.org/r/20240229144723.13047-2-edmund.raile@proton.me
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 25125a4762 upstream.
The update_cpumask(), checks for newly requested cpumask by calling
validate_change(), which returns an error on passing an invalid set
of cpu(s). Independent of the error returned, update_cpumask() always
returns zero, suppressing the error and returning success to the user
on writing an invalid cpu range for a cpuset. Fix it by returning
retval instead, which is returned by validate_change().
Fixes: 99fe36ba6f ("cgroup/cpuset: Improve temporary cpumasks handling")
Signed-off-by: Kamalesh Babulal <kamalesh.babulal@oracle.com>
Reviewed-by: Waiman Long <longman@redhat.com>
Cc: stable@vger.kernel.org # v6.6+
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 197331b27a upstream.
While commit 69f89168b3 ("usb: typec: tpcm: Fix issues with power being
removed during reset") fixes the boot issues for bus powered devices such
as LibreTech Renegade Elite/Firefly, it trades off the CC pins NOT being
Hi-Zed during errory recovery (i.e PORT_RESET) for devices which are NOT
bus powered(a.k.a self powered). This change Hi-Zs the CC pins only for
self powered devices, thus preventing brown out for bus powered devices
Adhering to spec is gaining more importance due to the Common charger
initiative enforced by the European Union.
Quoting from the spec:
4.5.2.2.2.1 ErrorRecovery State Requirements
The port shall not drive VBUS or VCONN, and shall present a
high-impedance to ground (above zOPEN) on its CC1 and CC2 pins.
Hi-Zing the CC pins is the inteded behavior for PORT_RESET.
CC pins are set to default state after tErrorRecovery in
PORT_RESET_WAIT_OFF.
4.5.2.2.2.2 Exiting From ErrorRecovery State
A Sink shall transition to Unattached.SNK after tErrorRecovery.
A Source shall transition to Unattached.SRC after tErrorRecovery.
Fixes: 69f89168b3 ("usb: typec: tpcm: Fix issues with power being removed during reset")
Cc: stable@vger.kernel.org
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Tested-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20240228000512.746252-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45bcc03465 upstream.
The test counter 'test_cnt' should not be returned in diag.sh, e.g. what
if only the 4th test fail? Will do 'exit 4' which is 'exit ${KSFT_SKIP}',
the whole test will be marked as skipped instead of 'failed'!
So we should do ret=${KSFT_FAIL} instead.
Fixes: df62f2ec3d ("selftests/mptcp: add diag interface tests")
Cc: stable@vger.kernel.org
Fixes: 42fb6cddec ("selftests: mptcp: more stable diag tests")
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc0c8f9089 upstream.
When debugging issues with a workload using SysV shmem, Michal Hocko has
come up with a reproducer that shows how a series of mprotect() operations
can result in an elevated shm_nattch and thus leak of the resource.
The problem is caused by wrong assumptions in vma_merge() commit
714965ca82 ("mm/mmap: start distinguishing if vma can be removed in
mergeability test"). The shmem vmas have a vma_ops->close callback that
decrements shm_nattch, and we remove the vma without calling it.
vma_merge() has thus historically avoided merging vma's with
vma_ops->close and commit 714965ca82 was supposed to keep it that way.
It relaxed the checks for vma_ops->close in can_vma_merge_after() assuming
that it is never called on a vma that would be a candidate for removal.
However, the vma_merge() code does also use the result of this check in
the decision to remove a different vma in the merge case 7.
A robust solution would be to refactor vma_merge() code in a way that the
vma_ops->close check is only done for vma's that are actually going to be
removed, and not as part of the preliminary checks. That would both solve
the existing bug, and also allow additional merges that the checks
currently prevent unnecessarily in some cases.
However to fix the existing bug first with a minimized risk, and for
easier stable backports, this patch only adds a vma_ops->close check to
the buggy case 7 specifically. All other cases of vma removal are covered
by the can_vma_merge_before() check that includes the test for
vma_ops->close.
The reproducer code, adapted from Michal Hocko's code:
int main(int argc, char *argv[]) {
int segment_id;
size_t segment_size = 20 * PAGE_SIZE;
char * sh_mem;
struct shmid_ds shmid_ds;
key_t key = 0x1234;
segment_id = shmget(key, segment_size,
IPC_CREAT | IPC_EXCL | S_IRUSR | S_IWUSR);
sh_mem = (char *)shmat(segment_id, NULL, 0);
mprotect(sh_mem + 2*PAGE_SIZE, PAGE_SIZE, PROT_NONE);
mprotect(sh_mem + PAGE_SIZE, PAGE_SIZE, PROT_WRITE);
mprotect(sh_mem + 2*PAGE_SIZE, PAGE_SIZE, PROT_WRITE);
shmdt(sh_mem);
shmctl(segment_id, IPC_STAT, &shmid_ds);
printf("nattch after shmdt(): %lu (expected: 0)\n", shmid_ds.shm_nattch);
if (shmctl(segment_id, IPC_RMID, 0))
printf("IPCRM failed %d\n", errno);
return (shmid_ds.shm_nattch) ? 1 : 0;
}
Link: https://lkml.kernel.org/r/20240222215930.14637-2-vbabka@suse.cz
Fixes: 714965ca82 ("mm/mmap: start distinguishing if vma can be removed in mergeability test")
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Reported-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com>
Reviewed-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a807e46aa upstream.
After a couple recent changes in LLVM, there is a warning (or error with
CONFIG_WERROR=y or W=e) from the compile time fortify source routines,
specifically the memset() in copy_to_user_tmpl().
In file included from net/xfrm/xfrm_user.c:14:
...
include/linux/fortify-string.h:438:4: error: call to '__write_overflow_field' declared with 'warning' attribute: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror,-Wattribute-warning]
438 | __write_overflow_field(p_size_field, size);
| ^
1 error generated.
While ->xfrm_nr has been validated against XFRM_MAX_DEPTH when its value
is first assigned in copy_templates() by calling validate_tmpl() first
(so there should not be any issue in practice), LLVM/clang cannot really
deduce that across the boundaries of these functions. Without that
knowledge, it cannot assume that the loop stops before i is greater than
XFRM_MAX_DEPTH, which would indeed result a stack buffer overflow in the
memset().
To make the bounds of ->xfrm_nr clear to the compiler and add additional
defense in case copy_to_user_tmpl() is ever used in a path where
->xfrm_nr has not been properly validated against XFRM_MAX_DEPTH first,
add an explicit bound check and early return, which clears up the
warning.
Cc: stable@vger.kernel.org
Link: https://github.com/ClangBuiltLinux/linux/issues/1985
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1834200384 upstream.
sun8i_ce_cipher_unprepare should be called before
crypto_finalize_skcipher_request, because client callbacks may
immediately free memory, that isn't needed anymore. But it will be
used by unprepare after free. Before removing prepare/unprepare
callbacks it was handled by crypto engine in crypto_finalize_request.
Usually that results in a pointer dereference problem during a in
crypto selftest.
Unable to handle kernel NULL pointer dereference at
virtual address 0000000000000030
Mem abort info:
ESR = 0x0000000096000004
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x04: level 0 translation fault
Data abort info:
ISV = 0, ISS = 0x00000004, ISS2 = 0x00000000
CM = 0, WnR = 0, TnD = 0, TagAccess = 0
GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0
user pgtable: 4k pages, 48-bit VAs, pgdp=000000004716d000
[0000000000000030] pgd=0000000000000000, p4d=0000000000000000
Internal error: Oops: 0000000096000004 [#1] SMP
This problem is detected by KASAN as well.
==================================================================
BUG: KASAN: slab-use-after-free in sun8i_ce_cipher_do_one+0x6e8/0xf80 [sun8i_ce]
Read of size 8 at addr ffff00000dcdc040 by task 1c15000.crypto-/373
Hardware name: Pine64 PinePhone (1.2) (DT)
Call trace:
dump_backtrace+0x9c/0x128
show_stack+0x20/0x38
dump_stack_lvl+0x48/0x60
print_report+0xf8/0x5d8
kasan_report+0x90/0xd0
__asan_load8+0x9c/0xc0
sun8i_ce_cipher_do_one+0x6e8/0xf80 [sun8i_ce]
crypto_pump_work+0x354/0x620 [crypto_engine]
kthread_worker_fn+0x244/0x498
kthread+0x168/0x178
ret_from_fork+0x10/0x20
Allocated by task 379:
kasan_save_stack+0x3c/0x68
kasan_set_track+0x2c/0x40
kasan_save_alloc_info+0x24/0x38
__kasan_kmalloc+0xd4/0xd8
__kmalloc+0x74/0x1d0
alg_test_skcipher+0x90/0x1f0
alg_test+0x24c/0x830
cryptomgr_test+0x38/0x60
kthread+0x168/0x178
ret_from_fork+0x10/0x20
Freed by task 379:
kasan_save_stack+0x3c/0x68
kasan_set_track+0x2c/0x40
kasan_save_free_info+0x38/0x60
__kasan_slab_free+0x100/0x170
slab_free_freelist_hook+0xd4/0x1e8
__kmem_cache_free+0x15c/0x290
kfree+0x74/0x100
kfree_sensitive+0x80/0xb0
alg_test_skcipher+0x12c/0x1f0
alg_test+0x24c/0x830
cryptomgr_test+0x38/0x60
kthread+0x168/0x178
ret_from_fork+0x10/0x20
The buggy address belongs to the object at ffff00000dcdc000
which belongs to the cache kmalloc-256 of size 256
The buggy address is located 64 bytes inside of
freed 256-byte region [ffff00000dcdc000, ffff00000dcdc100)
Signed-off-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Fixes: 4136212ab1 ("crypto: sun8i-ce - Remove prepare/unprepare request")
Cc: <stable@vger.kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b820954429 upstream.
The VMBUS_RING_SIZE macro adds space for a ring buffer header to the
requested ring buffer size. The header size is always 1 page, and so
its size varies based on the PAGE_SIZE for which the kernel is built.
If the requested ring buffer size is a large power-of-2 size and the header
size is small, the resulting size is inefficient in its use of memory.
For example, a 512 Kbyte ring buffer with a 4 Kbyte page size results in
a 516 Kbyte allocation, which is rounded to up 1 Mbyte by the memory
allocator, and wastes 508 Kbytes of memory.
In such situations, the exact size of the ring buffer isn't that important,
and it's OK to allocate the 4 Kbyte header at the beginning of the 512
Kbytes, leaving the ring buffer itself with just 508 Kbytes. The memory
allocation can be 512 Kbytes instead of 1 Mbyte and nothing is wasted.
Update VMBUS_RING_SIZE to implement this approach for "large" ring buffer
sizes. "Large" is somewhat arbitrarily defined as 8 times the size of
the ring buffer header (which is of size PAGE_SIZE). For example, for
4 Kbyte PAGE_SIZE, ring buffers of 32 Kbytes and larger use the first
4 Kbytes as the ring buffer header. For 64 Kbyte PAGE_SIZE, ring buffers
of 512 Kbytes and larger use the first 64 Kbytes as the ring buffer
header. In both cases, smaller sizes add space for the header so
the ring size isn't reduced too much by using part of the space for
the header. For example, with a 64 Kbyte page size, we don't want
a 128 Kbyte ring buffer to be reduced to 64 Kbytes by allocating half
of the space for the header. In such a case, the memory allocation
is less efficient, but it's the best that can be done.
While the new algorithm slightly changes the amount of space allocated
for ring buffers by drivers that use VMBUS_RING_SIZE, the devices aren't
known to be sensitive to small changes in ring buffer size, so there
shouldn't be any effect.
Fixes: c1135c7fd0 ("Drivers: hv: vmbus: Introduce types of GPADL")
Fixes: 6941f67ad3 ("hv_netvsc: Calculate correct ring size when PAGE_SIZE is not 4 Kbytes")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218502
Cc: stable@vger.kernel.org
Signed-off-by: Michael Kelley <mhklinux@outlook.com>
Reviewed-by: Saurabh Sengar <ssengar@linux.microsoft.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Tested-by: Souradeep Chakrabarti <schakrabarti@linux.microsoft.com>
Link: https://lore.kernel.org/r/20240229004533.313662-1-mhklinux@outlook.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <20240229004533.313662-1-mhklinux@outlook.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5f4fc4bd5c upstream.
This set combination is weird: it allows for elements to be
added/deleted, but once bound to the rule it cannot be updated anymore.
Eventually, all elements expire, leading to an empty set which cannot
be updated anymore. Reject this flags combination.
Cc: stable@vger.kernel.org
Fixes: 761da2935d ("netfilter: nf_tables: add set timeout API support")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 16603605b6 upstream.
Anonymous sets are never used with timeout from userspace, reject this.
Exception to this rule is NFT_SET_EVAL to ensure legacy meters still work.
Cc: stable@vger.kernel.org
Fixes: 761da2935d ("netfilter: nf_tables: add set timeout API support")
Reported-by: lonial con <kongln9170@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 552705a365 upstream.
While the rhashtable set gc runs asynchronously, a race allows it to
collect elements from anonymous sets with timeouts while it is being
released from the commit path.
Mingi Cho originally reported this issue in a different path in 6.1.x
with a pipapo set with low timeouts which is not possible upstream since
7395dfacff ("netfilter: nf_tables: use timestamp to check for set
element timeout").
Fix this by setting on the dead flag for anonymous sets to skip async gc
in this case.
According to 08e4c8c591 ("netfilter: nf_tables: mark newset as dead on
transaction abort"), Florian plans to accelerate abort path by releasing
objects via workqueue, therefore, this sets on the dead flag for abort
path too.
Cc: stable@vger.kernel.org
Fixes: 5f68718b34 ("netfilter: nf_tables: GC transaction API to avoid race with control plane")
Reported-by: Mingi Cho <mgcho.minic@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b4a11b2033 upstream.
Reproduce environment:
network with 3 VM linuxs is connected as below:
VM1<---->VM2(latest kernel 6.5.0-rc7)<---->VM3
VM1: eth0 ip: 192.168.122.207 MTU 1500
VM2: eth0 ip: 192.168.122.208, eth1 ip: 192.168.123.224 MTU 1500
VM3: eth0 ip: 192.168.123.240 MTU 1500
Reproduce:
VM1 send 1400 bytes UDP data to VM3 using tools scapy with flags=0.
scapy command:
send(IP(dst="192.168.123.240",flags=0)/UDP()/str('0'*1400),count=1,
inter=1.000000)
Result:
Before IP data is sent.
----------------------------------------------------------------------
root@qemux86-64:~# cat /proc/net/snmp
Ip: Forwarding DefaultTTL InReceives InHdrErrors InAddrErrors
ForwDatagrams InUnknownProtos InDiscards InDelivers OutRequests
OutDiscards OutNoRoutes ReasmTimeout ReasmReqds ReasmOKs ReasmFails
FragOKs FragFails FragCreates
Ip: 1 64 11 0 3 4 0 0 4 7 0 0 0 0 0 0 0 0 0
......
----------------------------------------------------------------------
After IP data is sent.
----------------------------------------------------------------------
root@qemux86-64:~# cat /proc/net/snmp
Ip: Forwarding DefaultTTL InReceives InHdrErrors InAddrErrors
ForwDatagrams InUnknownProtos InDiscards InDelivers OutRequests
OutDiscards OutNoRoutes ReasmTimeout ReasmReqds ReasmOKs ReasmFails
FragOKs FragFails FragCreates
Ip: 1 64 12 0 3 5 0 0 4 8 0 0 0 0 0 0 0 0 0
......
----------------------------------------------------------------------
"ForwDatagrams" increase from 4 to 5 and "OutRequests" also increase
from 7 to 8.
Issue description and patch:
IPSTATS_MIB_OUTPKTS("OutRequests") is counted with IPSTATS_MIB_OUTOCTETS
("OutOctets") in ip_finish_output2().
According to RFC 4293, it is "OutOctets" counted with "OutTransmits" but
not "OutRequests". "OutRequests" does not include any datagrams counted
in "ForwDatagrams".
ipSystemStatsOutOctets OBJECT-TYPE
DESCRIPTION
"The total number of octets in IP datagrams delivered to the
lower layers for transmission. Octets from datagrams
counted in ipIfStatsOutTransmits MUST be counted here.
ipSystemStatsOutRequests OBJECT-TYPE
DESCRIPTION
"The total number of IP datagrams that local IP user-
protocols (including ICMP) supplied to IP in requests for
transmission. Note that this counter does not include any
datagrams counted in ipSystemStatsOutForwDatagrams.
So do patch to define IPSTATS_MIB_OUTPKTS to "OutTransmits" and add
IPSTATS_MIB_OUTREQUESTS for "OutRequests".
Add IPSTATS_MIB_OUTREQUESTS counter in __ip_local_out() for ipv4 and add
IPSTATS_MIB_OUT counter in ip6_finish_output2() for ipv6.
Test result with patch:
Before IP data is sent.
----------------------------------------------------------------------
root@qemux86-64:~# cat /proc/net/snmp
Ip: Forwarding DefaultTTL InReceives InHdrErrors InAddrErrors
ForwDatagrams InUnknownProtos InDiscards InDelivers OutRequests
OutDiscards OutNoRoutes ReasmTimeout ReasmReqds ReasmOKs ReasmFails
FragOKs FragFails FragCreates OutTransmits
Ip: 1 64 9 0 5 1 0 0 3 3 0 0 0 0 0 0 0 0 0 4
......
root@qemux86-64:~# cat /proc/net/netstat
......
IpExt: InNoRoutes InTruncatedPkts InMcastPkts OutMcastPkts InBcastPkts
OutBcastPkts InOctets OutOctets InMcastOctets OutMcastOctets
InBcastOctets OutBcastOctets InCsumErrors InNoECTPkts InECT1Pkts
InECT0Pkts InCEPkts ReasmOverlaps
IpExt: 0 0 0 0 0 0 2976 1896 0 0 0 0 0 9 0 0 0 0
----------------------------------------------------------------------
After IP data is sent.
----------------------------------------------------------------------
root@qemux86-64:~# cat /proc/net/snmp
Ip: Forwarding DefaultTTL InReceives InHdrErrors InAddrErrors
ForwDatagrams InUnknownProtos InDiscards InDelivers OutRequests
OutDiscards OutNoRoutes ReasmTimeout ReasmReqds ReasmOKs ReasmFails
FragOKs FragFails FragCreates OutTransmits
Ip: 1 64 10 0 5 2 0 0 3 3 0 0 0 0 0 0 0 0 0 5
......
root@qemux86-64:~# cat /proc/net/netstat
......
IpExt: InNoRoutes InTruncatedPkts InMcastPkts OutMcastPkts InBcastPkts
OutBcastPkts InOctets OutOctets InMcastOctets OutMcastOctets
InBcastOctets OutBcastOctets InCsumErrors InNoECTPkts InECT1Pkts
InECT0Pkts InCEPkts ReasmOverlaps
IpExt: 0 0 0 0 0 0 4404 3324 0 0 0 0 0 10 0 0 0 0
----------------------------------------------------------------------
"ForwDatagrams" increase from 1 to 2 and "OutRequests" is keeping 3.
"OutTransmits" increase from 4 to 5 and "OutOctets" increase 1428.
Signed-off-by: Heng Guo <heng.guo@windriver.com>
Reviewed-by: Kun Song <Kun.Song@windriver.com>
Reviewed-by: Filip Pudak <filip.pudak@windriver.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported-by: Vitezslav Samel <vitezslav@samel.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8318d6a636 upstream.
Since we have set the WQ_NAME_LEN to 32, decrease the name of
events_freezable_power_efficient so that it does not trip the name length
warning when the workqueue is created.
Signed-off-by: Audra Mitchell <audra@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 71ce046327 ]
Some drivers require the mapped tt pages to be decrypted. In an ideal
world this would have been handled by the dma layer, but the TTM page
fault handling would have to be rewritten to able to do that.
A side-effect of the TTM page fault handling is using a dma allocation
per order (via ttm_pool_alloc_page) which makes it impossible to just
trivially use dma_mmap_attrs. As a result ttm has to be very careful
about trying to make its pgprot for the mapped tt pages match what
the dma layer thinks it is. At the ttm layer it's possible to
deduce the requirement to have tt pages decrypted by checking
whether coherent dma allocations have been requested and the system
is running with confidential computing technologies.
This approach isn't ideal but keeping TTM matching DMAs expectations
for the page properties is in general fragile, unfortunately proper
fix would require a rewrite of TTM's page fault handling.
Fixes vmwgfx with SEV enabled.
v2: Explicitly include cc_platform.h
v3: Use CC_ATTR_GUEST_MEM_ENCRYPT instead of CC_ATTR_MEM_ENCRYPT to
limit the scope to guests and log when memory decryption is enabled.
Signed-off-by: Zack Rusin <zack.rusin@broadcom.com>
Fixes: 3bf3710e37 ("drm/ttm: Add a generic TTM memcpy move for page-based iomem")
Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Acked-by: Christian König <christian.koenig@amd.com>
Cc: Huang Rui <ray.huang@amd.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Cc: <stable@vger.kernel.org> # v5.14+
Link: https://patchwork.freedesktop.org/patch/msgid/20230926040359.3040017-1-zack@kde.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 85da8f71aa ]
People are getting spooked by brcmfmac errors on their boot console.
There's no reason for these messages to be errors.
Cc: stable@vger.kernel.org # 6.2.x
Fixes: d6a5c56221 ("wifi: brcmfmac: add support for vendor-specific firmware api")
Signed-off-by: Hector Martin <marcan@marcan.st>
[arend.vanspriel@broadcom.com: remove attach/detach vendor callbacks]
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240106103835.269149-2-arend.vanspriel@broadcom.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f7861c56b ]
Using the WSEC command instead of sae_password seems to be the supported
mechanism on newer firmware, and also how the brcmdhd driver does it.
The existing firmware mechanism intended for (some) Cypress chips has
been separated from the new firmware mechanism using the multi-vendor
framework. Depending on the device it will select the appropriate
firmware mechanism.
This makes WPA3 work with iwd, or with wpa_supplicant pending a support
patchset [2].
[1] https://rachelbythebay.com/w/2023/11/06/wpa3/
[2] http://lists.infradead.org/pipermail/hostap/2023-July/041653.html
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Neal Gompa <neal@gompa.dev>
[arend.vanspriel@broadcom.com: use multi-vendor framework]
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240103095704.135651-5-arend.vanspriel@broadcom.com
Stable-dep-of: 85da8f71aa ("wifi: brcmfmac: Demote vendor-specific attach/detach messages to info")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 14e1391b71 ]
Adding a .feat_attach() callback allowing per-vendor overrides
of the driver feature flags. In this patch the callback is only
provided by BCA vendor to disable SAE feature as it has not been
confirmed yet. BCA chips generally do not have the in-driver
supplicant (idsup) feature so they rely on NL80211_CMD_EXTERNAL_AUTH
to trigger user-space authentication.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240103095704.135651-3-arend.vanspriel@broadcom.com
Stable-dep-of: 85da8f71aa ("wifi: brcmfmac: Demote vendor-specific attach/detach messages to info")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3f269ed0a ]
Since:
7ee18d6779 ("x86/power: Make restore_processor_context() sane")
kmemleak reports this issue:
unreferenced object 0xf68241e0 (size 32):
comm "swapper/0", pid 1, jiffies 4294668610 (age 68.432s)
hex dump (first 32 bytes):
00 cc cc cc 29 10 01 c0 00 00 00 00 00 00 00 00 ....)...........
00 42 82 f6 cc cc cc cc cc cc cc cc cc cc cc cc .B..............
backtrace:
[<461c1d50>] __kmem_cache_alloc_node+0x106/0x260
[<ea65e13b>] __kmalloc+0x54/0x160
[<c3858cd2>] msr_build_context.constprop.0+0x35/0x100
[<46635aff>] pm_check_save_msr+0x63/0x80
[<6b6bb938>] do_one_initcall+0x41/0x1f0
[<3f3add60>] kernel_init_freeable+0x199/0x1e8
[<3b538fde>] kernel_init+0x1a/0x110
[<938ae2b2>] ret_from_fork+0x1c/0x28
Which is a false positive.
Reproducer:
- Run rsync of whole kernel tree (multiple times if needed).
- start a kmemleak scan
- Note this is just an example: a lot of our internal tests hit these.
The root cause is similar to the fix in:
b0b592cf08 x86/pm: Fix false positive kmemleak report in msr_build_context()
ie. the alignment within the packed struct saved_context
which has everything unaligned as there is only "u16 gs;" at start of
struct where in the past there were four u16 there thus aligning
everything afterwards. The issue is with the fact that Kmemleak only
searches for pointers that are aligned (see how pointers are scanned in
kmemleak.c) so when the struct members are not aligned it doesn't see
them.
Testing:
We run a lot of tests with our CI, and after applying this fix we do not
see any kmemleak issues any more whilst without it we see hundreds of
the above report. From a single, simple test run consisting of 416 individual test
cases on kernel 5.10 x86 with kmemleak enabled we got 20 failures due to this,
which is quite a lot. With this fix applied we get zero kmemleak related failures.
Fixes: 7ee18d6779 ("x86/power: Make restore_processor_context() sane")
Signed-off-by: Anton Altaparmakov <anton@tuxera.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: stable@vger.kernel.org
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lore.kernel.org/r/20240314142656.17699-1-anton@tuxera.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c6064cbe5 ]
Otherwise after the GTT bo is released, the GTT and gart space is freed
but amdgpu_ttm_backend_unbind will not clear the gart page table entry
and leave valid mapping entry pointing to the stale system page. Then
if GPU access the gart address mistakely, it will read undefined value
instead page fault, harder to debug and reproduce the real issue.
Cc: stable@vger.kernel.org
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6cd8adc3e1 ]
Previously, patches have been added to limit the reported count of SATA
ports for asm1064 and asm1166 SATA controllers, as those controllers do
report more ports than physically having.
While it is allowed to report more ports than physically having in CAP.NP,
it is not allowed to report more ports than physically having in the PI
(Ports Implemented) register, which is what these HBAs do.
(This is a AHCI spec violation.)
Unfortunately, it seems that the PMP implementation in these ASMedia HBAs
is also violating the AHCI and SATA-IO PMP specification.
What these HBAs do is that they do not report that they support PMP
(CAP.SPM (Supports Port Multiplier) is not set).
Instead, they have decided to add extra "virtual" ports in the PI register
that is used if a port multiplier is connected to any of the physical
ports of the HBA.
Enumerating the devices behind the PMP as specified in the AHCI and
SATA-IO specifications, by using PMP READ and PMP WRITE commands to the
physical ports of the HBA is not possible, you have to use the "virtual"
ports.
This is of course bad, because this gives us no way to detect the device
and vendor ID of the PMP actually connected to the HBA, which means that
we can not apply the proper PMP quirks for the PMP that is connected to
the HBA.
Limiting the port map will thus stop these controllers from working with
SATA Port Multipliers.
This patch reverts both patches for asm1064 and asm1166, so old behavior
is restored and SATA PMP will work again, but it will also reintroduce the
(minutes long) extra boot time for the ASMedia controllers that do not
have a PMP connected (either on the PCIe card itself, or an external PMP).
However, a longer boot time for some, is the lesser evil compared to some
other users not being able to detect their drives at all.
Fixes: 0077a504e1 ("ahci: asm1166: correct count of reported ports")
Fixes: 9815e39617 ("ahci: asm1064: correct count of reported ports")
Cc: stable@vger.kernel.org
Reported-by: Matt <cryptearth@googlemail.com>
Signed-off-by: Conrad Kostecki <conikost@gentoo.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
[cassel: rewrote commit message]
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e995f5dd9a ]
This option is needed to continue booting with QEMU. Recent changes that
made this optional meant that it gets unset in the test harness, and so
WireGuard CI has been broken. Fix this by simply setting this option.
Cc: stable@vger.kernel.org
Fixes: 496ea826d1 ("RISC-V: provide Kconfig & commandline options to control parsing "riscv,isa"")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 71cbd32e3d ]
The previous commit fixed a bug that led to a NULL peer->device being
dereferenced. It's actually easier and faster performance-wise to
instead get the device from ctx->wg. This semantically makes more sense
too, since ctx->wg->peer_allowedips.seq is compared with
ctx->allowedips_seq, basing them both in ctx. This also acts as a
defence in depth provision against freed peers.
Cc: stable@vger.kernel.org
Fixes: e7096c131e ("net: WireGuard secure network tunnel")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55b6c73867 ]
If all peers are removed via wg_peer_remove_all(), rather than setting
peer_list to empty, the peer is added to a temporary list with a head on
the stack of wg_peer_remove_all(). If a netlink dump is resumed and the
cursored peer is one that has been removed via wg_peer_remove_all(), it
will iterate from that peer and then attempt to dump freed peers.
Fix this by instead checking peer->is_dead, which was explictly created
for this purpose. Also move up the device_update_lock lockdep assertion,
since reading is_dead relies on that.
It can be reproduced by a small script like:
echo "Setting config..."
ip link add dev wg0 type wireguard
wg setconf wg0 /big-config
(
while true; do
echo "Showing config..."
wg showconf wg0 > /dev/null
done
) &
sleep 4
wg setconf wg0 <(printf "[Peer]\nPublicKey=$(wg genkey)\n")
Resulting in:
BUG: KASAN: slab-use-after-free in __lock_acquire+0x182a/0x1b20
Read of size 8 at addr ffff88811956ec70 by task wg/59
CPU: 2 PID: 59 Comm: wg Not tainted 6.8.0-rc2-debug+ #5
Call Trace:
<TASK>
dump_stack_lvl+0x47/0x70
print_address_description.constprop.0+0x2c/0x380
print_report+0xab/0x250
kasan_report+0xba/0xf0
__lock_acquire+0x182a/0x1b20
lock_acquire+0x191/0x4b0
down_read+0x80/0x440
get_peer+0x140/0xcb0
wg_get_device_dump+0x471/0x1130
Cc: stable@vger.kernel.org
Fixes: e7096c131e ("net: WireGuard secure network tunnel")
Reported-by: Lillian Berry <lillian@star-ark.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fea1c949f6 ]
The LoongArch CRC32 hw acceleration is based on arch/mips/crypto/
crc32-mips.c. While the MIPS code supports both MIPS32 and MIPS64,
but LoongArch32 lacks the CRC instruction. As a result, the line
"len -= sizeof(u32)" is unnecessary.
Removing it can make context code style more unified and improve
code readability.
Cc: stable@vger.kernel.org
Reviewed-by: WANG Xuerui <git@xen0n.name>
Suggested-by: Wentao Guan <guanwentao@uniontech.com>
Signed-off-by: Yuli Wang <wangyuli@uniontech.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c68ece8b2 ]
Commit fb24ea52f7 ("drivers: Remove explicit invocations of
mmiowb()") remove all mmiowb() in drivers, but it says:
"NOTE: mmiowb() has only ever guaranteed ordering in conjunction with
spin_unlock(). However, pairing each mmiowb() removal in this patch with
the corresponding call to spin_unlock() is not at all trivial, so there
is a small chance that this change may regress any drivers incorrectly
relying on mmiowb() to order MMIO writes between CPUs using lock-free
synchronisation."
The mmio in radeon_ring_commit() is protected by a mutex rather than a
spinlock, but in the mutex fastpath it behaves similar to spinlock. We
can add mmiowb() calls in the radeon driver but the maintainer says he
doesn't like such a workaround, and radeon is not the only example of
mutex protected mmio.
So we should extend the mmiowb tracking system from spinlock to mutex,
and maybe other locking primitives. This is not easy and error prone, so
we solve it in the architectural code, by simply defining the __io_aw()
hook as mmiowb(). And we no longer need to override queued_spin_unlock()
so use the generic definition.
Without this, we get such an error when run 'glxgears' on weak ordering
architectures such as LoongArch:
radeon 0000:04:00.0: ring 0 stalled for more than 10324msec
radeon 0000:04:00.0: ring 3 stalled for more than 10240msec
radeon 0000:04:00.0: GPU lockup (current fence id 0x000000000001f412 last fence id 0x000000000001f414 on ring 3)
radeon 0000:04:00.0: GPU lockup (current fence id 0x000000000000f940 last fence id 0x000000000000f941 on ring 0)
radeon 0000:04:00.0: scheduling IB failed (-35).
[drm:radeon_gem_va_ioctl [radeon]] *ERROR* Couldn't update BO_VA (-35)
radeon 0000:04:00.0: scheduling IB failed (-35).
[drm:radeon_gem_va_ioctl [radeon]] *ERROR* Couldn't update BO_VA (-35)
radeon 0000:04:00.0: scheduling IB failed (-35).
[drm:radeon_gem_va_ioctl [radeon]] *ERROR* Couldn't update BO_VA (-35)
radeon 0000:04:00.0: scheduling IB failed (-35).
[drm:radeon_gem_va_ioctl [radeon]] *ERROR* Couldn't update BO_VA (-35)
radeon 0000:04:00.0: scheduling IB failed (-35).
[drm:radeon_gem_va_ioctl [radeon]] *ERROR* Couldn't update BO_VA (-35)
radeon 0000:04:00.0: scheduling IB failed (-35).
[drm:radeon_gem_va_ioctl [radeon]] *ERROR* Couldn't update BO_VA (-35)
radeon 0000:04:00.0: scheduling IB failed (-35).
[drm:radeon_gem_va_ioctl [radeon]] *ERROR* Couldn't update BO_VA (-35)
Link: https://lore.kernel.org/dri-devel/29df7e26-d7a8-4f67-b988-44353c4270ac@amd.com/T/#t
Link: https://lore.kernel.org/linux-arch/20240301130532.3953167-1-chenhuacai@loongson.cn/T/#t
Cc: stable@vger.kernel.org
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c87e12e0e8 ]
From GCC commit 3f13154553f8546a ("df-scan: remove ad-hoc handling of
global regs in asms"), global registers will no longer be forced to add
to the def-use chain. Then current_thread_info(), current_stack_pointer
and __my_cpu_offset may be lifted out of the loop because they are no
longer treated as "volatile variables".
This optimization is still correct for the current_thread_info() and
current_stack_pointer usages because they are associated to a thread.
However it is wrong for __my_cpu_offset because it is associated to a
CPU rather than a thread: if the thread migrates to a different CPU in
the loop, __my_cpu_offset should be changed.
Change __my_cpu_offset definition to treat it as a "volatile variable",
in order to avoid such a mis-optimization.
Cc: stable@vger.kernel.org
Reported-by: Xiaotian Wu <wuxiaotian@loongson.cn>
Reported-by: Miao Wang <shankerwangmiao@gmail.com>
Signed-off-by: Xing Li <lixing@loongson.cn>
Signed-off-by: Hongchen Zhang <zhanghongchen@loongson.cn>
Signed-off-by: Rui Wang <wangrui@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 310227f428 ]
Currently, we don't reenable the config if freezing the device failed.
For example, virtio-mem currently doesn't support suspend+resume, and
trying to freeze the device will always fail. Afterwards, the device
will no longer respond to resize requests, because it won't get notified
about config changes.
Let's fix this by re-enabling the config if freezing fails.
Fixes: 22b7050a02 ("virtio: defer config changed notifications")
Cc: <stable@kernel.org>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20240213135425.795001-1-david@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c87126096 ]
The TP_STRUCT__entry that gets assigned the region name, or an
empty string if no region is present, is erroneously initialized
to the cxl_region pointer. It needs to be properly initialized
otherwise it's length is wrong and garbage chars can appear in
the kernel trace output: /sys/kernel/tracing/trace
The bad initialization was due in part to a naming conflict with
the parameter: struct cxl_region *region. The field 'region' is
already exposed externally as the region name, so changing that
to something logical, like 'region_name' is not an option. Instead
rename the internal only struct cxl_region to the commonly used
'cxlr'.
Impact is that tooling depending on that trace data can miss
picking up a valid event when searching by region name. The
TP_printk() output, if enabled, does emit the correct region
names in the dmesg log.
This was found during testing of the cxl-list option to report
media-errors for a region.
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Jonathan Cameron <jonathan.cameron@huawei.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: stable@vger.kernel.org
Fixes: ddf49d57b8 ("cxl/trace: Add TRACE support for CXL media-error records")
Signed-off-by: Alison Schofield <alison.schofield@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f9952e8d8 ]
The __string() and __assign_str() helper macros of the TRACE_EVENT() macro
are going through some optimizations where only the source string of
__string() will be used and the __assign_str() source will be ignored and
later removed.
To make sure that there's no issues, a new check is added between the
__string() src argument and the __assign_str() src argument that does a
strcmp() to make sure they are the same string.
The hclgevf trace events have:
__assign_str(devname, &hdev->nic.kinfo.netdev->name);
Which triggers the warning:
hclgevf_trace.h:34:39: error: passing argument 1 of ‘strcmp’ from incompatible pointer type [-Werror=incompatible-pointer-types]
34 | __assign_str(devname, &hdev->nic.kinfo.netdev->name);
[..]
arch/x86/include/asm/string_64.h:75:24: note: expected ‘const char *’ but argument is of type ‘char (*)[16]’
75 | int strcmp(const char *cs, const char *ct);
| ~~~~~~~~~~~~^~
Because __assign_str() now has:
WARN_ON_ONCE(__builtin_constant_p(src) ? \
strcmp((src), __data_offsets.dst##_ptr_) : \
(src) != __data_offsets.dst##_ptr_); \
The problem is the '&' on hdev->nic.kinfo.netdev->name. That's because
that name is:
char name[IFNAMSIZ]
Where passing an address '&' of a char array is not compatible with strcmp().
The '&' is not necessary, remove it.
Link: https://lore.kernel.org/linux-trace-kernel/20240313093454.3909afe7@gandalf.local.home
Cc: netdev <netdev@vger.kernel.org>
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Cc: Salil Mehta <salil.mehta@huawei.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Yufeng Mo <moyufeng@huawei.com>
Cc: Huazhong Tan <tanhuazhong@huawei.com>
Cc: stable@vger.kernel.org
Acked-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Jijie Shao <shaojijie@huawei.com>
Fixes: d8355240cf ("net: hns3: add trace event support for PF/VF mailbox")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9388a2aa45 ]
I'm working on restructuring the __string* macros so that it doesn't need
to recalculate the string twice. That is, it will save it off when
processing __string() and the __assign_str() will not need to do the work
again as it currently does.
Currently __string_len(item, src, len) doesn't actually use "src", but my
changes will require src to be correct as that is where the __assign_str()
will get its value from.
The event class nfsd_clid_class has:
__string_len(name, name, clp->cl_name.len)
But the second "name" does not exist and causes my changes to fail to
build. That second parameter should be: clp->cl_name.data.
Link: https://lore.kernel.org/linux-trace-kernel/20240222122828.3d8d213c@gandalf.local.home
Cc: Neil Brown <neilb@suse.de>
Cc: Olga Kornievskaia <kolga@netapp.com>
Cc: Dai Ngo <Dai.Ngo@oracle.com>
Cc: Tom Talpey <tom@talpey.com>
Cc: stable@vger.kernel.org
Fixes: d27b74a867 ("NFSD: Use new __string_len C macros for nfsd_clid_class")
Acked-by: Chuck Lever <chuck.lever@oracle.com>
Acked-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3198822c6 ]
When the skb is reorganized during esp_output (!esp->inline), the pages
coming from the original skb fragments are supposed to be released back
to the system through put_page. But if the skb fragment pages are
originating from a page_pool, calling put_page on them will trigger a
page_pool leak which will eventually result in a crash.
This leak can be easily observed when using CONFIG_DEBUG_VM and doing
ipsec + gre (non offloaded) forwarding:
BUG: Bad page state in process ksoftirqd/16 pfn:1451b6
page:00000000de2b8d32 refcount:0 mapcount:0 mapping:0000000000000000 index:0x1451b6000 pfn:0x1451b6
flags: 0x200000000000000(node=0|zone=2)
page_type: 0xffffffff()
raw: 0200000000000000 dead000000000040 ffff88810d23c000 0000000000000000
raw: 00000001451b6000 0000000000000001 00000000ffffffff 0000000000000000
page dumped because: page_pool leak
Modules linked in: ip_gre gre mlx5_ib mlx5_core xt_conntrack xt_MASQUERADE nf_conntrack_netlink nfnetlink iptable_nat nf_nat xt_addrtype br_netfilter rpcrdma rdma_ucm ib_iser libiscsi scsi_transport_iscsi ib_umad rdma_cm ib_ipoib iw_cm ib_cm ib_uverbs ib_core overlay zram zsmalloc fuse [last unloaded: mlx5_core]
CPU: 16 PID: 96 Comm: ksoftirqd/16 Not tainted 6.8.0-rc4+ #22
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x36/0x50
bad_page+0x70/0xf0
free_unref_page_prepare+0x27a/0x460
free_unref_page+0x38/0x120
esp_ssg_unref.isra.0+0x15f/0x200
esp_output_tail+0x66d/0x780
esp_xmit+0x2c5/0x360
validate_xmit_xfrm+0x313/0x370
? validate_xmit_skb+0x1d/0x330
validate_xmit_skb_list+0x4c/0x70
sch_direct_xmit+0x23e/0x350
__dev_queue_xmit+0x337/0xba0
? nf_hook_slow+0x3f/0xd0
ip_finish_output2+0x25e/0x580
iptunnel_xmit+0x19b/0x240
ip_tunnel_xmit+0x5fb/0xb60
ipgre_xmit+0x14d/0x280 [ip_gre]
dev_hard_start_xmit+0xc3/0x1c0
__dev_queue_xmit+0x208/0xba0
? nf_hook_slow+0x3f/0xd0
ip_finish_output2+0x1ca/0x580
ip_sublist_rcv_finish+0x32/0x40
ip_sublist_rcv+0x1b2/0x1f0
? ip_rcv_finish_core.constprop.0+0x460/0x460
ip_list_rcv+0x103/0x130
__netif_receive_skb_list_core+0x181/0x1e0
netif_receive_skb_list_internal+0x1b3/0x2c0
napi_gro_receive+0xc8/0x200
gro_cell_poll+0x52/0x90
__napi_poll+0x25/0x1a0
net_rx_action+0x28e/0x300
__do_softirq+0xc3/0x276
? sort_range+0x20/0x20
run_ksoftirqd+0x1e/0x30
smpboot_thread_fn+0xa6/0x130
kthread+0xcd/0x100
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x31/0x50
? kthread_complete_and_exit+0x20/0x20
ret_from_fork_asm+0x11/0x20
</TASK>
The suggested fix is to introduce a new wrapper (skb_page_unref) that
covers page refcounting for page_pool pages as well.
Cc: stable@vger.kernel.org
Fixes: 6a5bcd84e8 ("page_pool: Allow drivers to hint on SKB recycling")
Reported-and-tested-by: Anatoli N.Chechelnickiy <Anatoli.Chechelnickiy@m.interpipe.biz>
Reported-by: Ian Kumlien <ian.kumlien@gmail.com>
Link: https://lore.kernel.org/netdev/CAA85sZvvHtrpTQRqdaOx6gd55zPAVsqMYk_Lwh4Md5knTq7AyA@mail.gmail.com
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: Mina Almasry <almasrymina@google.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d2399501c2 ]
Commit 0499a78369 ("ARM64: Dynamically allocate cpumasks and increase
supported CPUs to 512") changed the handling of cpumasks on ARM 64bit,
what resulted in the strange issues and warnings during cpufreq-dt
initialization on some big.LITTLE platforms.
This was caused by mixing OPPs between big and LITTLE cores, because
OPP-sharing information between big and LITTLE cores is computed on
cpumask, which in turn was not zeroed on allocation. Fix this by
switching to zalloc_cpumask_var() call.
Fixes: dc279ac6e5 ("cpufreq: dt: Refactor initialization to handle probe deferral properly")
CC: stable@vger.kernel.org # v5.10+
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Christoph Lameter (Ampere) <cl@linux.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78ffbefba8 ]
As a matter of fact, continuous reads require additional handling at the
operation level in order for them to work properly. The core helpers do
have this additional logic now, but any time a controller implements its
own page helper, this extra logic is "lost". This means we need another
level of per-controller driver checks to ensure they can leverage
continuous reads. This is for now unsupported, so in order to ensure
continuous reads are enabled only when fully using the core page
helpers, we need to add more initial checks.
Also, as performance is not relevant during raw accesses, we also
prevent these from enabling the feature.
This should solve the issue seen with controllers such as the STM32 FMC2
when in sequencer mode. In this case, the continuous read feature would
be enabled but not leveraged, and most importantly not disabled, leading
to further operations to fail.
Reported-by: Christophe Kerello <christophe.kerello@foss.st.com>
Fixes: 003fe4b954 ("mtd: rawnand: Support for sequential cache reads")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Christophe Kerello <christophe.kerello@foss.st.com>
Link: https://lore.kernel.org/linux-mtd/20240307115315.1942678-1-miquel.raynal@bootlin.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 16a57d7681 ]
Several users have reported this log getting dumped too regularly to
kernel log. The likely root cause has been identified, and it suggests
that this situation is expected for some configurations
(for example SMB2.1).
Since the function returns appropriately even for such cases, it is
fairly harmless to make this a debug log. When needed, the verbosity
can be increased to capture this log.
Cc: stable@vger.kernel.org
Reported-by: Jan Čermák <sairon@sairon.cz>
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d606c311b ]
The return values for cifs_chan_update_iface() didn't match what the
documentation said and nothing was checking them anyway. Just make it
a void function.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Stable-dep-of: 16a57d7681 ("cifs: reduce warning log level for server not advertising interfaces")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3a11c0ec6 ]
We return early if "iface" is NULL so there is no need to check here.
Delete those checks.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Stable-dep-of: 16a57d7681 ("cifs: reduce warning log level for server not advertising interfaces")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 12d1e301bd ]
cifs_chan_update_iface is meant to check and update the server
interface used for a channel when the existing server interface
is no longer available.
So far, this handler had the code to remove an interface entry
even if a new candidate interface is not available. Allowing
this leads to several corner cases to handle.
This change makes the logic much simpler by not deallocating
the current channel interface entry if a new interface is not
found to replace it with.
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Stable-dep-of: 16a57d7681 ("cifs: reduce warning log level for server not advertising interfaces")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 13c0a74747 ]
Some code paths for querying server interfaces make a false
assumption that it will only get called for SMB3+. Since this
function now can get called from a generic code paths, the correct
thing to do is to have specific handler for this functionality
per SMB dialect, and call this handler.
This change adds such a handler and implements this handler only
for SMB 3.0 and 3.1.1.
Cc: stable@vger.kernel.org
Cc: Jan Čermák <sairon@sairon.cz>
Reported-by: Paulo Alcantara <pc@manguebit.com>
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4cf6e1101a ]
We were passing 0 as the xid for the call to query
server interfaces. This is not great for debugging.
This change adds a real xid.
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com>
Reviewed-by: Bharath SM <bharathsm@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Stable-dep-of: 13c0a74747 ("cifs: make sure server interfaces are requested only for SMB3+")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 269cdf353b ]
Fix a bug where nilfs_get_block() returns a successful status when
searching and inserting the specified block both fail inconsistently. If
this inconsistent behavior is not due to a previously fixed bug, then an
unexpected race is occurring, so return a temporary error -EAGAIN instead.
This prevents callers such as __block_write_begin_int() from requesting a
read into a buffer that is not mapped, which would cause the BUG_ON check
for the BH_Mapped flag in submit_bh_wbc() to fail.
Link: https://lkml.kernel.org/r/20240313105827.5296-3-konishi.ryusuke@gmail.com
Fixes: 1f5abe7e7d ("nilfs2: replace BUG_ON and BUG calls triggerable from ioctl")
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2f26b4a84 ]
Patch series "nilfs2: fix kernel bug at submit_bh_wbc()".
This resolves a kernel BUG reported by syzbot. Since there are two
flaws involved, I've made each one a separate patch.
The first patch alone resolves the syzbot-reported bug, but I think
both fixes should be sent to stable, so I've tagged them as such.
This patch (of 2):
Syzbot has reported a kernel bug in submit_bh_wbc() when writing file data
to a nilfs2 file system whose metadata is corrupted.
There are two flaws involved in this issue.
The first flaw is that when nilfs_get_block() locates a data block using
btree or direct mapping, if the disk address translation routine
nilfs_dat_translate() fails with internal code -ENOENT due to DAT metadata
corruption, it can be passed back to nilfs_get_block(). This causes
nilfs_get_block() to misidentify an existing block as non-existent,
causing both data block lookup and insertion to fail inconsistently.
The second flaw is that nilfs_get_block() returns a successful status in
this inconsistent state. This causes the caller __block_write_begin_int()
or others to request a read even though the buffer is not mapped,
resulting in a BUG_ON check for the BH_Mapped flag in submit_bh_wbc()
failing.
This fixes the first issue by changing the return value to code -EINVAL
when a conversion using DAT fails with code -ENOENT, avoiding the
conflicting condition that leads to the kernel bug described above. Here,
code -EINVAL indicates that metadata corruption was detected during the
block lookup, which will be properly handled as a file system error and
converted to -EIO when passing through the nilfs2 bmap layer.
Link: https://lkml.kernel.org/r/20240313105827.5296-1-konishi.ryusuke@gmail.com
Link: https://lkml.kernel.org/r/20240313105827.5296-2-konishi.ryusuke@gmail.com
Fixes: c3a7abf06c ("nilfs2: support contiguous lookup of blocks")
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Reported-by: syzbot+cfed5b56649bddf80d6e@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=cfed5b56649bddf80d6e
Tested-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 74b0ebcbdd ]
In f2fs_do_write_data_page, FI_ATOMIC_FILE flag selects the target inode
between the original inode and COW inode. When aborting atomic write and
writeback occur simultaneously, invalid data can be written to original
inode if the FI_ATOMIC_FILE flag is cleared meanwhile.
To prevent the problem, let's truncate all pages before clearing the flag
Atomic write thread Writeback thread
f2fs_abort_atomic_write
clear_inode_flag(inode, FI_ATOMIC_FILE)
__writeback_single_inode
do_writepages
f2fs_do_write_data_page
- use dn of original inode
truncate_inode_pages_final
Fixes: 3db1de0e58 ("f2fs: change the current atomic write way")
Cc: stable@vger.kernel.org #v5.19+
Reviewed-by: Sungjong Seo <sj1557.seo@samsung.com>
Reviewed-by: Yeongjin Gil <youngjin.gil@samsung.com>
Signed-off-by: Sunmin Jeong <s_min.jeong@samsung.com>
Reviewed-by: Daeho Jeong <daehojeong@google.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4bf7832234 ]
In f2fs_update_inode, i_size of the atomic file isn't updated until
FI_ATOMIC_COMMITTED flag is set. When committing atomic write right
after the writeback of the inode, i_size of the raw inode will not be
updated. It can cause the atomicity corruption due to a mismatch between
old file size and new data.
To prevent the problem, let's mark inode dirty for FI_ATOMIC_COMMITTED
Atomic write thread Writeback thread
__writeback_single_inode
write_inode
f2fs_update_inode
- skip i_size update
f2fs_ioc_commit_atomic_write
f2fs_commit_atomic_write
set_inode_flag(inode, FI_ATOMIC_COMMITTED)
f2fs_do_sync_file
f2fs_fsync_node_pages
- skip f2fs_update_inode since the inode is clean
Fixes: 3db1de0e58 ("f2fs: change the current atomic write way")
Cc: stable@vger.kernel.org #v5.19+
Reviewed-by: Sungjong Seo <sj1557.seo@samsung.com>
Reviewed-by: Yeongjin Gil <youngjin.gil@samsung.com>
Signed-off-by: Sunmin Jeong <s_min.jeong@samsung.com>
Reviewed-by: Daeho Jeong <daehojeong@google.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 584c2a9184 ]
smp_call_function_single disables IRQs when executing the callback. To
prevent deadlocks, we must disable IRQs when taking cgr_lock elsewhere.
This is already done by qman_update_cgr and qman_delete_cgr; fix the
other lockers.
Fixes: 96f413f476 ("soc/fsl/qbman: fix issue in qman_delete_cgr_safe()")
CC: stable@vger.kernel.org
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Reviewed-by: Camelia Groza <camelia.groza@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8145f1c35f ]
If a reader of the ring buffer is doing a poll, and waiting for the ring
buffer to hit a specific watermark, there could be a case where it gets
into an infinite ping-pong loop.
The poll code has:
rbwork->full_waiters_pending = true;
if (!cpu_buffer->shortest_full ||
cpu_buffer->shortest_full > full)
cpu_buffer->shortest_full = full;
The writer will see full_waiters_pending and check if the ring buffer is
filled over the percentage of the shortest_full value. If it is, it calls
an irq_work to wake up all the waiters.
But the code could get into a circular loop:
CPU 0 CPU 1
----- -----
[ Poll ]
[ shortest_full = 0 ]
rbwork->full_waiters_pending = true;
if (rbwork->full_waiters_pending &&
[ buffer percent ] > shortest_full) {
rbwork->wakeup_full = true;
[ queue_irqwork ]
cpu_buffer->shortest_full = full;
[ IRQ work ]
if (rbwork->wakeup_full) {
cpu_buffer->shortest_full = 0;
wakeup poll waiters;
[woken]
if ([ buffer percent ] > full)
break;
rbwork->full_waiters_pending = true;
if (rbwork->full_waiters_pending &&
[ buffer percent ] > shortest_full) {
rbwork->wakeup_full = true;
[ queue_irqwork ]
cpu_buffer->shortest_full = full;
[ IRQ work ]
if (rbwork->wakeup_full) {
cpu_buffer->shortest_full = 0;
wakeup poll waiters;
[woken]
[ Wash, rinse, repeat! ]
In the poll, the shortest_full needs to be set before the
full_pending_waiters, as once that is set, the writer will compare the
current shortest_full (which is incorrect) to decide to call the irq_work,
which will reset the shortest_full (expecting the readers to update it).
Also move the setting of full_waiters_pending after the check if the ring
buffer has the required percentage filled. There's no reason to tell the
writer to wake up waiters if there are no waiters.
Link: https://lore.kernel.org/linux-trace-kernel/20240312131952.630922155@goodmis.org
Cc: stable@vger.kernel.org
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Fixes: 42fb0a1e84 ("tracing/ring-buffer: Have polling block on watermark")
Reviewed-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68282dd930 ]
The "shortest_full" variable is used to keep track of the waiter that is
waiting for the smallest amount on the ring buffer before being woken up.
When a tasks waits on the ring buffer, it passes in a "full" value that is
a percentage. 0 means wake up on any data. 1-100 means wake up from 1% to
100% full buffer.
As all waiters are on the same wait queue, the wake up happens for the
waiter with the smallest percentage.
The problem is that the smallest_full on the cpu_buffer that stores the
smallest amount doesn't get reset when all the waiters are woken up. It
does get reset when the ring buffer is reset (echo > /sys/kernel/tracing/trace).
This means that tasks may be woken up more often then when they want to
be. Instead, have the shortest_full field get reset just before waking up
all the tasks. If the tasks wait again, they will update the shortest_full
before sleeping.
Also add locking around setting of shortest_full in the poll logic, and
change "work" to "rbwork" to match the variable name for rb_irq_work
structures that are used in other places.
Link: https://lore.kernel.org/linux-trace-kernel/20240308202431.948914369@goodmis.org
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linke li <lilinke99@qq.com>
Cc: Rabin Vincent <rabin@rab.in>
Fixes: 2c2b0a78b3 ("ring-buffer: Add percentage of ring buffer full to wake up reader")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Stable-dep-of: 8145f1c35f ("ring-buffer: Fix full_waiters_pending in poll")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 761d9473e2 ]
The rb_watermark_hit() checks if the amount of data in the ring buffer is
above the percentage level passed in by the "full" variable. If it is, it
returns true.
But it also sets the "shortest_full" field of the cpu_buffer that informs
writers that it needs to call the irq_work if the amount of data on the
ring buffer is above the requested amount.
The rb_watermark_hit() always sets the shortest_full even if the amount in
the ring buffer is what it wants. As it is not going to wait, because it
has what it wants, there's no reason to set shortest_full.
Link: https://lore.kernel.org/linux-trace-kernel/20240312115641.6aa8ba08@gandalf.local.home
Cc: stable@vger.kernel.org
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Fixes: 42fb0a1e84 ("tracing/ring-buffer: Have polling block on watermark")
Reviewed-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b359457368 ]
A task can wait on a ring buffer for when it fills up to a specific
watermark. The writer will check the minimum watermark that waiters are
waiting for and if the ring buffer is past that, it will wake up all the
waiters.
The waiters are in a wait loop, and will first check if a signal is
pending and then check if the ring buffer is at the desired level where it
should break out of the loop.
If a file that uses a ring buffer closes, and there's threads waiting on
the ring buffer, it needs to wake up those threads. To do this, a
"wait_index" was used.
Before entering the wait loop, the waiter will read the wait_index. On
wakeup, it will check if the wait_index is different than when it entered
the loop, and will exit the loop if it is. The waker will only need to
update the wait_index before waking up the waiters.
This had a couple of bugs. One trivial one and one broken by design.
The trivial bug was that the waiter checked the wait_index after the
schedule() call. It had to be checked between the prepare_to_wait() and
the schedule() which it was not.
The main bug is that the first check to set the default wait_index will
always be outside the prepare_to_wait() and the schedule(). That's because
the ring_buffer_wait() doesn't have enough context to know if it should
break out of the loop.
The loop itself is not needed, because all the callers to the
ring_buffer_wait() also has their own loop, as the callers have a better
sense of what the context is to decide whether to break out of the loop
or not.
Just have the ring_buffer_wait() block once, and if it gets woken up, exit
the function and let the callers decide what to do next.
Link: https://lore.kernel.org/all/CAHk-=whs5MdtNjzFkTyaUy=vHi=qwWgPi0JgTe6OYUYMNSRZfg@mail.gmail.com/
Link: https://lore.kernel.org/linux-trace-kernel/20240308202431.792933613@goodmis.org
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linke li <lilinke99@qq.com>
Cc: Rabin Vincent <rabin@rab.in>
Fixes: e30f53aad2 ("tracing: Do not busy wait in buffer splice")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Stable-dep-of: 761d9473e2 ("ring-buffer: Do not set shortest_full when full target is hit")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 810cd4bb53 ]
Mask operations through config space changes to DisINTx may race INTx
configuration changes via ioctl. Create wrappers that add locking for
paths outside of the core interrupt code.
In particular, irq_type is updated holding igate, therefore testing
is_intx() requires holding igate. For example clearing DisINTx from
config space can otherwise race changes of the interrupt configuration.
This aligns interfaces which may trigger the INTx eventfd into two
camps, one side serialized by igate and the other only enabled while
INTx is configured. A subsequent patch introduces synchronization for
the latter flows.
Cc: <stable@vger.kernel.org>
Fixes: 89e1f7d4c6 ("vfio: Add PCI device driver")
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/r/20240308230557.805580-3-alex.williamson@redhat.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe9a708268 ]
Currently for devices requiring masking at the irqchip for INTx, ie.
devices without DisINTx support, the IRQ is enabled in request_irq()
and subsequently disabled as necessary to align with the masked status
flag. This presents a window where the interrupt could fire between
these events, resulting in the IRQ incrementing the disable depth twice.
This would be unrecoverable for a user since the masked flag prevents
nested enables through vfio.
Instead, invert the logic using IRQF_NO_AUTOEN such that exclusive INTx
is never auto-enabled, then unmask as required.
Cc: <stable@vger.kernel.org>
Fixes: 89e1f7d4c6 ("vfio: Add PCI device driver")
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/r/20240308230557.805580-2-alex.williamson@redhat.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1eb537bf4 ]
There are cases where a session is disconnected and password has changed
on the server (or expired) for this user and this currently can not
be fixed without unmount and mounting again. This patch allows
remount to change the password (for the non Kerberos case, Kerberos
ticket refresh is handled differently) when the session is disconnected
and the user can not reconnect due to still using old password.
Future patches should also allow us to setup the keyring (cifscreds)
to have an "alternate password" so we would be able to change
the password before the session drops (without the risk of races
between when the password changes and the disconnect occurs -
ie cases where the old password is still needed because the new
password has not fully rolled out to all servers yet).
Cc: stable@vger.kernel.org
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e4b61f3b1c ]
In cases of large directories, the readdir operation may span multiple
round trips to retrieve contents. This introduces a potential race
condition in case of concurrent write and readdir operations. If the
readdir operation initiates before a write has been processed by the
server, it may update the file size attribute to an older value.
Address this issue by avoiding file size updates from readdir when we
have read/write lease.
Scenario:
1) process1: open dir xyz
2) process1: readdir instance 1 on xyz
3) process2: create file.txt for write
4) process2: write x bytes to file.txt
5) process2: close file.txt
6) process2: open file.txt for read
7) process1: readdir 2 - overwrites file.txt inode size to 0
8) process2: read contents of file.txt - bug, short read with 0 bytes
Cc: stable@vger.kernel.org
Reviewed-by: Shyam Prasad N <sprasad@microsoft.com>
Signed-off-by: Bharath SM <bharathsm@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d039984c1 ]
Query dir responses don't provide enough information on reparse points
such as major/minor numbers and symlink targets other than reparse
tags, however we don't need to unconditionally revalidate them only
because they are reparse points. Instead, revalidate them only when
their ctime or reparse tag has changed.
For instance, Windows Server updates ctime of reparse points when
their data have changed.
Signed-off-by: Paulo Alcantara (SUSE) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Stable-dep-of: e4b61f3b1c ("cifs: prevent updating file size from server if we have a read/write lease")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b5ff74c1ef ]
For a physical PCI device that is passed through to a Hyper-V guest VM,
current code specifies the VMBus ring buffer size as 4 pages. But this
is an inappropriate dependency, since the amount of ring buffer space
needed is unrelated to PAGE_SIZE. For example, on x86 the ring buffer
size ends up as 16 Kbytes, while on ARM64 with 64 Kbyte pages, the ring
size bloats to 256 Kbytes. The ring buffer for PCI pass-thru devices
is used for only a few messages during device setup and removal, so any
space above a few Kbytes is wasted.
Fix this by declaring the ring buffer size to be a fixed 16 Kbytes.
Furthermore, use the VMBUS_RING_SIZE() macro so that the ring buffer
header is properly accounted for, and so the size is rounded up to a
page boundary, using the page size for which the kernel is built. While
w/64 Kbyte pages this results in a 64 Kbyte ring buffer header plus a
64 Kbyte ring buffer, that's the smallest possible with that page size.
It's still 128 Kbytes better than the current code.
Link: https://lore.kernel.org/linux-pci/20240216202240.251818-1-mhklinux@outlook.com
Signed-off-by: Michael Kelley <mhklinux@outlook.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Ilpo Jarvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Long Li <longli@microsoft.com>
Cc: <stable@vger.kernel.org> # 5.15.x
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 72e34b8593 ]
The commit message in commit fc9a77040b ("PCI: designware-ep: Configure
Resizable BAR cap to advertise the smallest size") claims that it modifies
the Resizable BAR capability to only advertise support for 1 MB size BARs.
However, the commit writes all zeroes to PCI_REBAR_CAP (the register which
contains the possible BAR sizes that a BAR be resized to).
According to the spec, it is illegal to not have a bit set in
PCI_REBAR_CAP, and 1 MB is the smallest size allowed.
Set bit 4 in PCI_REBAR_CAP, so that we actually advertise support for a
1 MB BAR size.
Before:
Capabilities: [2e8 v1] Physical Resizable BAR
BAR 0: current size: 1MB
BAR 1: current size: 1MB
BAR 2: current size: 1MB
BAR 3: current size: 1MB
BAR 4: current size: 1MB
BAR 5: current size: 1MB
After:
Capabilities: [2e8 v1] Physical Resizable BAR
BAR 0: current size: 1MB, supported: 1MB
BAR 1: current size: 1MB, supported: 1MB
BAR 2: current size: 1MB, supported: 1MB
BAR 3: current size: 1MB, supported: 1MB
BAR 4: current size: 1MB, supported: 1MB
BAR 5: current size: 1MB, supported: 1MB
Fixes: fc9a77040b ("PCI: designware-ep: Configure Resizable BAR cap to advertise the smallest size")
Link: https://lore.kernel.org/linux-pci/20240307111520.3303774-1-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: <stable@vger.kernel.org> # 5.2
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf79e33cdd ]
Qcom SoCs making use of ARM SMMU require BDF to SID translation table in
the driver to properly map the SID for the PCIe devices based on their BDF
identifier. This is currently achieved with the help of
qcom_pcie_config_sid_1_9_0() function for SoCs supporting the 1_9_0 config.
But With newer Qcom SoCs starting from SM8450, BDF to SID translation is
set to bypass mode by default in hardware. Due to this, the translation
table that is set in the qcom_pcie_config_sid_1_9_0() is essentially
unused and the default SID is used for all endpoints in SoCs starting from
SM8450.
This is a security concern and also warrants swapping the DeviceID in DT
while using the GIC ITS to handle MSIs from endpoints. The swapping is
currently done like below in DT when using GIC ITS:
/*
* MSIs for BDF (1:0.0) only works with Device ID 0x5980.
* Hence, the IDs are swapped.
*/
msi-map = <0x0 &gic_its 0x5981 0x1>,
<0x100 &gic_its 0x5980 0x1>;
Here, swapping of the DeviceIDs ensure that the endpoint with BDF (1:0.0)
gets the DeviceID 0x5980 which is associated with the default SID as per
the iommu mapping in DT. So MSIs were delivered with IDs swapped so far.
But this also means the Root Port (0:0.0) won't receive any MSIs (for PME,
AER etc...)
So let's fix these issues by clearing the BDF to SID bypass mode for all
SoCs making use of the 1_9_0 config. This allows the PCIe devices to use
the correct SID, thus avoiding the DeviceID swapping hack in DT and also
achieving the isolation between devices.
Fixes: 4c93988221 ("PCI: qcom: Add support for configuring BDF to SID mapping for SM8250")
Link: https://lore.kernel.org/linux-pci/20240307-pci-bdf-sid-fix-v1-1-9423a7e2d63c@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Cc: stable@vger.kernel.org # 5.11
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 75b5ab134b ]
Clang enables -Wenum-enum-conversion and -Wenum-compare-conditional
under -Wenum-conversion. A recent change in Clang strengthened these
warnings and they appear frequently in common builds, primarily due to
several instances in common headers but there are quite a few drivers
that have individual instances as well.
include/linux/vmstat.h:508:43: warning: arithmetic between different enumeration types ('enum zone_stat_item' and 'enum numa_stat_item') [-Wenum-enum-conversion]
508 | return vmstat_text[NR_VM_ZONE_STAT_ITEMS +
| ~~~~~~~~~~~~~~~~~~~~~ ^
509 | item];
| ~~~~
drivers/net/wireless/intel/iwlwifi/mvm/mac-ctxt.c:955:24: warning: conditional expression between different enumeration types ('enum iwl_mac_beacon_flags' and 'enum iwl_mac_beacon_flags_v1') [-Wenum-compare-conditional]
955 | flags |= is_new_rate ? IWL_MAC_BEACON_CCK
| ^ ~~~~~~~~~~~~~~~~~~
956 | : IWL_MAC_BEACON_CCK_V1;
| ~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/intel/iwlwifi/mvm/mac-ctxt.c:1120:21: warning: conditional expression between different enumeration types ('enum iwl_mac_beacon_flags' and 'enum iwl_mac_beacon_flags_v1') [-Wenum-compare-conditional]
1120 | 0) > 10 ?
| ^
1121 | IWL_MAC_BEACON_FILS :
| ~~~~~~~~~~~~~~~~~~~
1122 | IWL_MAC_BEACON_FILS_V1;
| ~~~~~~~~~~~~~~~~~~~~~~
Doing arithmetic between or returning two different types of enums could
be a bug, so each of the instance of the warning needs to be evaluated.
Unfortunately, as mentioned above, there are many instances of this
warning in many different configurations, which can break the build when
CONFIG_WERROR is enabled.
To avoid introducing new instances of the warnings while cleaning up the
disruption for the majority of users, disable these warnings for the
default build while leaving them on for W=1 builds.
Cc: stable@vger.kernel.org
Closes: https://github.com/ClangBuiltLinux/linux/issues/2002
Link: 8c2ae42b3e
Acked-by: Yonghong Song <yonghong.song@linux.dev>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 17f46b803d ]
In production we have been hitting the following warning consistently
------------[ cut here ]------------
refcount_t: underflow; use-after-free.
WARNING: CPU: 17 PID: 1800359 at lib/refcount.c:28 refcount_warn_saturate+0x9c/0xe0
Workqueue: nfsiod nfs_direct_write_schedule_work [nfs]
RIP: 0010:refcount_warn_saturate+0x9c/0xe0
PKRU: 55555554
Call Trace:
<TASK>
? __warn+0x9f/0x130
? refcount_warn_saturate+0x9c/0xe0
? report_bug+0xcc/0x150
? handle_bug+0x3d/0x70
? exc_invalid_op+0x16/0x40
? asm_exc_invalid_op+0x16/0x20
? refcount_warn_saturate+0x9c/0xe0
nfs_direct_write_schedule_work+0x237/0x250 [nfs]
process_one_work+0x12f/0x4a0
worker_thread+0x14e/0x3b0
? ZSTD_getCParams_internal+0x220/0x220
kthread+0xdc/0x120
? __btf_name_valid+0xa0/0xa0
ret_from_fork+0x1f/0x30
This is because we're completing the nfs_direct_request twice in a row.
The source of this is when we have our commit requests to submit, we
process them and send them off, and then in the completion path for the
commit requests we have
if (nfs_commit_end(cinfo.mds))
nfs_direct_write_complete(dreq);
However since we're submitting asynchronous requests we sometimes have
one that completes before we submit the next one, so we end up calling
complete on the nfs_direct_request twice.
The only other place we use nfs_generic_commit_list() is in
__nfs_commit_inode, which wraps this call in a
nfs_commit_begin();
nfs_commit_end();
Which is a common pattern for this style of completion handling, one
that is also repeated in the direct code with get_dreq()/put_dreq()
calls around where we process events as well as in the completion paths.
Fix this by using the same pattern for the commit requests.
Before with my 200 node rocksdb stress running this warning would pop
every 10ish minutes. With my patch the stress test has been running for
several hours without popping.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Cc: stable@vger.kernel.org
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit deaef31bc1 ]
If we loop for multishot receive on the initial attempt, and then abort
later on to wait for more, we miss a case where we should be copying the
io_async_msghdr from the stack to stable storage. This leads to the next
retry potentially failing, if the application had the msghdr on the
stack.
Cc: stable@vger.kernel.org
Fixes: 9bb66906f2 ("io_uring: support multishot in recvmsg")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 002bf2fbc0 ]
PM runtime can be done simultaneously with AER error handling. Avoid that
by using pm_runtime_get_sync() before and pm_runtime_put() after reset in
pcie_do_recovery() for all recovering devices.
pm_runtime_get_sync() will increase dev->power.usage_count counter to
prevent any possible future request to runtime suspend a device. It will
also resume a device, if it was previously in D3hot state.
I tested with igc device by doing simultaneous aer_inject and rpm
suspend/resume via /sys/bus/pci/devices/PCI_ID/power/control and can
reproduce:
igc 0000:02:00.0: not ready 65535ms after bus reset; giving up
pcieport 0000:00:1c.2: AER: Root Port link has been reset (-25)
pcieport 0000:00:1c.2: AER: subordinate device reset failed
pcieport 0000:00:1c.2: AER: device recovery failed
igc 0000:02:00.0: Unable to change power state from D3hot to D0, device inaccessible
The problem disappears when this patch is applied.
Link: https://lore.kernel.org/r/20240212120135.146068-1-stanislaw.gruszka@linux.intel.com
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6c8dafc9d ]
When userland echoes 8bit characters to /dev/synth with e.g.
echo -e '\xe9' > /dev/synth
synth_write would get characters beyond 0x7f, and thus negative when
char is signed. When given to synth_buffer_add which takes a u16, this
would sign-extend and produce a U+ffxy character rather than U+xy.
Users thus get garbled text instead of accents in their output.
Let's fix this by making sure that we read unsigned characters.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Fixes: 89fc2ae80b ("speakup: extend synth buffer to 16bit unicode characters")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240204155736.2oh4ot7tiaa2wpbh@begin
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84fa943d93 ]
This commit resolves an issue in the tegra-xudc USB gadget driver that
incorrectly fetched USB3 PHY instances. The problem stemmed from the
assumption of a one-to-one correspondence between USB2 and USB3 PHY
names and their association with physical USB ports in the device tree.
Previously, the driver associated USB3 PHY names directly with the USB3
instance number, leading to mismatches when mapping the physical USB
ports. For instance, if using USB3-1 PHY, the driver expect the
corresponding PHY name as 'usb3-1'. However, the physical USB ports in
the device tree were designated as USB2-0 and USB3-0 as we only have
one device controller, causing a misalignment.
This commit rectifies the issue by adjusting the PHY naming logic.
Now, the driver correctly correlates the USB2 and USB3 PHY instances,
allowing the USB2-0 and USB3-1 PHYs to form a physical USB port pair
while accurately reflecting their configuration in the device tree by
naming them USB2-0 and USB3-0, respectively.
The change ensures that the PHY and PHY names align appropriately,
resolving the mismatch between physical USB ports and their associated
names in the device tree.
Fixes: b4e19931c9 ("usb: gadget: tegra-xudc: Support multiple device modes")
Cc: stable@vger.kernel.org
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20240307030328.1487748-3-waynec@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6b3bfe176 ]
We observed a corruption during on-line resize of a file system that is
larger than 16 TiB with 4k block size. With having more then 2^32 blocks
resize_inode is turned off by default by mke2fs. The issue can be
reproduced on a smaller file system for convenience by explicitly
turning off resize_inode. An on-line resize across an 8 GiB boundary (the
size of a meta block group in this setup) then leads to a corruption:
dev=/dev/<some_dev> # should be >= 16 GiB
mkdir -p /corruption
/sbin/mke2fs -t ext4 -b 4096 -O ^resize_inode $dev $((2 * 2**21 - 2**15))
mount -t ext4 $dev /corruption
dd if=/dev/zero bs=4096 of=/corruption/test count=$((2*2**21 - 4*2**15))
sha1sum /corruption/test
# 79d2658b39dcfd77274e435b0934028adafaab11 /corruption/test
/sbin/resize2fs $dev $((2*2**21))
# drop page cache to force reload the block from disk
echo 1 > /proc/sys/vm/drop_caches
sha1sum /corruption/test
# 3c2abc63cbf1a94c9e6977e0fbd72cd832c4d5c3 /corruption/test
2^21 = 2^15*2^6 equals 8 GiB whereof 2^15 is the number of blocks per
block group and 2^6 are the number of block groups that make a meta
block group.
The last checksum might be different depending on how the file is laid
out across the physical blocks. The actual corruption occurs at physical
block 63*2^15 = 2064384 which would be the location of the backup of the
meta block group's block descriptor. During the on-line resize the file
system will be converted to meta_bg starting at s_first_meta_bg which is
2 in the example - meaning all block groups after 16 GiB. However, in
ext4_flex_group_add we might add block groups that are not part of the
first meta block group yet. In the reproducer we achieved this by
substracting the size of a whole block group from the point where the
meta block group would start. This must be considered when updating the
backup block group descriptors to follow the non-meta_bg layout. The fix
is to add a test whether the group to add is already part of the meta
block group or not.
Fixes: 01f795f9e0 ("ext4: add online resizing support for meta_bg and 64-bit file systems")
Cc: <stable@vger.kernel.org>
Signed-off-by: Maximilian Heyne <mheyne@amazon.de>
Tested-by: Srivathsa Dara <srivathsa.d.dara@oracle.com>
Reviewed-by: Srivathsa Dara <srivathsa.d.dara@oracle.com>
Link: https://lore.kernel.org/r/20240215155009.94493-1-mheyne@amazon.de
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f003fda98 ]
Add of_match table for "ti,amc6821" compatible string.
This fixes automatic driver loading by userspace when using device-tree,
and if built as a module like major linux distributions do.
While devices probe just fine with i2c_device_id table, userspace can't
match the "ti,amc6821" compatible string from dt with the plain
"amc6821" device id. As a result, the kernel module can not be loaded.
Cc: stable@vger.kernel.org
Signed-off-by: Josua Mayer <josua@solid-run.com>
Link: https://lore.kernel.org/r/20240307-amc6821-of-match-v1-1-5f40464a3110@solid-run.com
[groeck: Cleaned up patch description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b735ee173f ]
The hwdb selection logic as a feature that allows it to mark some fields
as 'don't care'. If we match with such a field we memcpy(..)
the current etnaviv_chip_identity into ident.
This step can overwrite some id values read from the GPU with the
'don't care' value.
Fix this issue by restoring the affected values after the memcpy(..).
As this is crucial for user space to know when this feature works as
expected increment the minor version too.
Fixes: 4078a1186d ("drm/etnaviv: update hwdb selection logic")
Cc: stable@vger.kernel.org
Signed-off-by: Christian Gmeiner <cgmeiner@igalia.com>
Reviewed-by: Tomeu Vizoso <tomeu@tomeuvizoso.net>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 415798bc07 ]
Commit d5e01266e7 ("leds: trigger: netdev: add additional specific link
speed mode") in the various changes, reworked the way to set the LINKUP
mode in commit cee4bd16c3 ("leds: trigger: netdev: Recheck
NETDEV_LED_MODE_LINKUP on dev rename") and moved it to a generic function.
This changed the logic where, in the previous implementation the dev
from the trigger event was used to check if the carrier was ok, but in
the new implementation with the generic function, the dev in
trigger_data is used instead.
This is problematic and cause a possible kernel panic due to the fact
that the dev in the trigger_data still reference the old one as the
new one (passed from the trigger event) still has to be hold and saved
in the trigger_data struct (done in the NETDEV_REGISTER case).
On calling of get_device_state(), an invalid net_dev is used and this
cause a kernel panic.
To handle this correctly, move the call to get_device_state() after the
new net_dev is correctly set in trigger_data (in the NETDEV_REGISTER
case) and correctly parse the new dev.
Fixes: d5e01266e7 ("leds: trigger: netdev: add additional specific link speed mode")
Cc: stable@vger.kernel.org
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240203235413.1146-1-ansuelsmth@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 82b1c07a0a ]
There was previously a theoretical window where swapoff() could run and
teardown a swap_info_struct while a call to free_swap_and_cache() was
running in another thread. This could cause, amongst other bad
possibilities, swap_page_trans_huge_swapped() (called by
free_swap_and_cache()) to access the freed memory for swap_map.
This is a theoretical problem and I haven't been able to provoke it from a
test case. But there has been agreement based on code review that this is
possible (see link below).
Fix it by using get_swap_device()/put_swap_device(), which will stall
swapoff(). There was an extra check in _swap_info_get() to confirm that
the swap entry was not free. This isn't present in get_swap_device()
because it doesn't make sense in general due to the race between getting
the reference and swapoff. So I've added an equivalent check directly in
free_swap_and_cache().
Details of how to provoke one possible issue (thanks to David Hildenbrand
for deriving this):
--8<-----
__swap_entry_free() might be the last user and result in
"count == SWAP_HAS_CACHE".
swapoff->try_to_unuse() will stop as soon as soon as si->inuse_pages==0.
So the question is: could someone reclaim the folio and turn
si->inuse_pages==0, before we completed swap_page_trans_huge_swapped().
Imagine the following: 2 MiB folio in the swapcache. Only 2 subpages are
still references by swap entries.
Process 1 still references subpage 0 via swap entry.
Process 2 still references subpage 1 via swap entry.
Process 1 quits. Calls free_swap_and_cache().
-> count == SWAP_HAS_CACHE
[then, preempted in the hypervisor etc.]
Process 2 quits. Calls free_swap_and_cache().
-> count == SWAP_HAS_CACHE
Process 2 goes ahead, passes swap_page_trans_huge_swapped(), and calls
__try_to_reclaim_swap().
__try_to_reclaim_swap()->folio_free_swap()->delete_from_swap_cache()->
put_swap_folio()->free_swap_slot()->swapcache_free_entries()->
swap_entry_free()->swap_range_free()->
...
WRITE_ONCE(si->inuse_pages, si->inuse_pages - nr_entries);
What stops swapoff to succeed after process 2 reclaimed the swap cache
but before process1 finished its call to swap_page_trans_huge_swapped()?
--8<-----
Link: https://lkml.kernel.org/r/20240306140356.3974886-1-ryan.roberts@arm.com
Fixes: 7c00bafee8 ("mm/swap: free swap slots in batch")
Closes: https://lore.kernel.org/linux-mm/65a66eb9-41f8-4790-8db2-0c70ea15979f@redhat.com/
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: "Huang, Ying" <ying.huang@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8a1e58345 ]
mac802154_llsec_key_del() can free resources of a key directly without
following the RCU rules for waiting before the end of a grace period. This
may lead to use-after-free in case llsec_lookup_key() is traversing the
list of keys in parallel with a key deletion:
refcount_t: addition on 0; use-after-free.
WARNING: CPU: 4 PID: 16000 at lib/refcount.c:25 refcount_warn_saturate+0x162/0x2a0
Modules linked in:
CPU: 4 PID: 16000 Comm: wpan-ping Not tainted 6.7.0 #19
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.2-debian-1.16.2-1 04/01/2014
RIP: 0010:refcount_warn_saturate+0x162/0x2a0
Call Trace:
<TASK>
llsec_lookup_key.isra.0+0x890/0x9e0
mac802154_llsec_encrypt+0x30c/0x9c0
ieee802154_subif_start_xmit+0x24/0x1e0
dev_hard_start_xmit+0x13e/0x690
sch_direct_xmit+0x2ae/0xbc0
__dev_queue_xmit+0x11dd/0x3c20
dgram_sendmsg+0x90b/0xd60
__sys_sendto+0x466/0x4c0
__x64_sys_sendto+0xe0/0x1c0
do_syscall_64+0x45/0xf0
entry_SYSCALL_64_after_hwframe+0x6e/0x76
Also, ieee802154_llsec_key_entry structures are not freed by
mac802154_llsec_key_del():
unreferenced object 0xffff8880613b6980 (size 64):
comm "iwpan", pid 2176, jiffies 4294761134 (age 60.475s)
hex dump (first 32 bytes):
78 0d 8f 18 80 88 ff ff 22 01 00 00 00 00 ad de x.......".......
00 00 00 00 00 00 00 00 03 00 cd ab 00 00 00 00 ................
backtrace:
[<ffffffff81dcfa62>] __kmem_cache_alloc_node+0x1e2/0x2d0
[<ffffffff81c43865>] kmalloc_trace+0x25/0xc0
[<ffffffff88968b09>] mac802154_llsec_key_add+0xac9/0xcf0
[<ffffffff8896e41a>] ieee802154_add_llsec_key+0x5a/0x80
[<ffffffff8892adc6>] nl802154_add_llsec_key+0x426/0x5b0
[<ffffffff86ff293e>] genl_family_rcv_msg_doit+0x1fe/0x2f0
[<ffffffff86ff46d1>] genl_rcv_msg+0x531/0x7d0
[<ffffffff86fee7a9>] netlink_rcv_skb+0x169/0x440
[<ffffffff86ff1d88>] genl_rcv+0x28/0x40
[<ffffffff86fec15c>] netlink_unicast+0x53c/0x820
[<ffffffff86fecd8b>] netlink_sendmsg+0x93b/0xe60
[<ffffffff86b91b35>] ____sys_sendmsg+0xac5/0xca0
[<ffffffff86b9c3dd>] ___sys_sendmsg+0x11d/0x1c0
[<ffffffff86b9c65a>] __sys_sendmsg+0xfa/0x1d0
[<ffffffff88eadbf5>] do_syscall_64+0x45/0xf0
[<ffffffff890000ea>] entry_SYSCALL_64_after_hwframe+0x6e/0x76
Handle the proper resource release in the RCU callback function
mac802154_llsec_key_del_rcu().
Note that if llsec_lookup_key() finds a key, it gets a refcount via
llsec_key_get() and locally copies key id from key_entry (which is a
list element). So it's safe to call llsec_key_put() and free the list
entry after the RCU grace period elapses.
Found by Linux Verification Center (linuxtesting.org).
Fixes: 5d637d5aab ("mac802154: add llsec structures and mutators")
Cc: stable@vger.kernel.org
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Acked-by: Alexander Aring <aahringo@redhat.com>
Message-ID: <20240228163840.6667-1-pchelkin@ispras.ru>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 35f20786c4 ]
arch/powerpc/lib/xor_vmx.o is built with '-msoft-float' (from the main
powerpc Makefile) and '-maltivec' (from its CFLAGS), which causes an
error when building with clang after a recent change in main:
error: option '-msoft-float' cannot be specified with '-maltivec'
make[6]: *** [scripts/Makefile.build:243: arch/powerpc/lib/xor_vmx.o] Error 1
Explicitly add '-mhard-float' before '-maltivec' in xor_vmx.o's CFLAGS
to override the previous inclusion of '-msoft-float' (as the last option
wins), which matches how other areas of the kernel use '-maltivec', such
as AMDGPU.
Cc: stable@vger.kernel.org
Closes: https://github.com/ClangBuiltLinux/linux/issues/1986
Link: 4792f912b2
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20240127-ppc-xor_vmx-drop-msoft-float-v1-1-f24140e81376@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 95009ae904 ]
The lockdep assert is added by commit a448af25be ("md/raid10: remove
rcu protection to access rdev from conf") in print_conf(). And I didn't
notice that dm-raid is calling "pers->hot_add_disk" without holding
'reconfig_mutex'.
"pers->hot_add_disk" read and write many fields that is protected by
'reconfig_mutex', and raid_resume() already grab the lock in other
contex. Hence fix this problem by protecting "pers->host_add_disk"
with the lock.
Fixes: 9092c02d94 ("DM RAID: Add ability to restore transiently failed devices on resume")
Fixes: a448af25be ("md/raid10: remove rcu protection to access rdev from conf")
Cc: stable@vger.kernel.org # v6.7+
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Xiao Ni <xni@redhat.com>
Acked-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20240305072306.2562024-10-yukuai1@huaweicloud.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 627c6db207 ]
Commit 5459c0b704 ("PCI/DPC: Quirk PIO log size for certain Intel Root
Ports") and commit 3b8803494a ("PCI/DPC: Quirk PIO log size for Intel Ice
Lake Root Ports") add quirks for Ice, Tiger and Alder Lake Root Ports.
System firmware for Raptor Lake still has the bug, so Linux logs the
warning below on several Raptor Lake systems like Dell Precision 3581 with
Intel Raptor Lake processor (0W18NX) system firmware/BIOS version 1.10.1.
pci 0000:00:07.0: [8086:a76e] type 01 class 0x060400
pci 0000:00:07.0: DPC: RP PIO log size 0 is invalid
pci 0000:00:07.1: [8086:a73f] type 01 class 0x060400
pci 0000:00:07.1: DPC: RP PIO log size 0 is invalid
Apply the quirk for Raptor Lake Root Ports as well.
This also enables the DPC driver to dump the RP PIO Log registers when DPC
is triggered.
Link: https://lore.kernel.org/r/20240305113057.56468-1-pmenzel@molgen.mpg.de
Reported-by: Niels van Aert <nvaert1986@hotmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218560
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: <stable@vger.kernel.org>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Niels van Aert <nvaert1986@hotmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d5286d4e7 ]
A race condition between the .runtime_idle() callback and the .remove()
callback in the rtsx_pcr PCI driver leads to a kernel crash due to an
unhandled page fault [1].
The problem is that rtsx_pci_runtime_idle() is not expected to be running
after pm_runtime_get_sync() has been called, but the latter doesn't really
guarantee that. It only guarantees that the suspend and resume callbacks
will not be running when it returns.
However, if a .runtime_idle() callback is already running when
pm_runtime_get_sync() is called, the latter will notice that the runtime PM
status of the device is RPM_ACTIVE and it will return right away without
waiting for the former to complete. In fact, it cannot wait for
.runtime_idle() to complete because it may be called from that callback (it
arguably does not make much sense to do that, but it is not strictly
prohibited).
Thus in general, whoever is providing a .runtime_idle() callback needs
to protect it from running in parallel with whatever code runs after
pm_runtime_get_sync(). [Note that .runtime_idle() will not start after
pm_runtime_get_sync() has returned, but it may continue running then if it
has started earlier.]
One way to address that race condition is to call pm_runtime_barrier()
after pm_runtime_get_sync() (not before it, because a nonzero value of the
runtime PM usage counter is necessary to prevent runtime PM callbacks from
being invoked) to wait for the .runtime_idle() callback to complete should
it be running at that point. A suitable place for doing that is in
pci_device_remove() which calls pm_runtime_get_sync() before removing the
driver, so it may as well call pm_runtime_barrier() subsequently, which
will prevent the race in question from occurring, not just in the rtsx_pcr
driver, but in any PCI drivers providing .runtime_idle() callbacks.
Link: https://lore.kernel.org/lkml/20240229062201.49500-1-kai.heng.feng@canonical.com/ # [1]
Link: https://lore.kernel.org/r/5761426.DvuYhMxLoT@kreacher
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Ricky Wu <ricky_wu@realtek.com>
Acked-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d139ded8b9 ]
[BUG]
If qgroup is marked inconsistent (e.g. caused by operations needing full
subtree rescan, like creating a snapshot and assign to a higher level
qgroup), btrfs would immediately start leaking its data reserved space.
The following script can easily reproduce it:
mkfs.btrfs -O quota -f $dev
mount $dev $mnt
btrfs subvolume create $mnt/subv1
btrfs qgroup create 1/0 $mnt
# This snapshot creation would mark qgroup inconsistent,
# as the ownership involves different higher level qgroup, thus
# we have to rescan both source and snapshot, which can be very
# time consuming, thus here btrfs just choose to mark qgroup
# inconsistent, and let users to determine when to do the rescan.
btrfs subv snapshot -i 1/0 $mnt/subv1 $mnt/snap1
# Now this write would lead to qgroup rsv leak.
xfs_io -f -c "pwrite 0 64k" $mnt/file1
# And at unmount time, btrfs would report 64K DATA rsv space leaked.
umount $mnt
And we would have the following dmesg output for the unmount:
BTRFS info (device dm-1): last unmount of filesystem 14a3d84e-f47b-4f72-b053-a8a36eef74d3
BTRFS warning (device dm-1): qgroup 0/5 has unreleased space, type 0 rsv 65536
[CAUSE]
Since commit e15e9f43c7 ("btrfs: introduce
BTRFS_QGROUP_RUNTIME_FLAG_NO_ACCOUNTING to skip qgroup accounting"),
we introduce a mode for btrfs qgroup to skip the timing consuming
backref walk, if the qgroup is already inconsistent.
But this skip also covered the data reserved freeing, thus the qgroup
reserved space for each newly created data extent would not be freed,
thus cause the leakage.
[FIX]
Make the data extent reserved space freeing mandatory.
The qgroup reserved space handling is way cheaper compared to the
backref walking part, and we always have the super sensitive leak
detector, thus it's definitely worth to always free the qgroup
reserved data space.
Reported-by: Fabian Vogt <fvogt@suse.com>
Fixes: e15e9f43c7 ("btrfs: introduce BTRFS_QGROUP_RUNTIME_FLAG_NO_ACCOUNTING to skip qgroup accounting")
CC: stable@vger.kernel.org # 6.1+
Link: https://bugzilla.suse.com/show_bug.cgi?id=1216196
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 801410b26a ]
During the handoff from earlycon to the real console driver, we have
two separate drivers operating on the same device concurrently. In the
case of the 8250 driver these concurrent accesses cause problems due
to the driver's use of banked registers, controlled by LCR.DLAB. It is
possible for the setup(), config_port(), pm() and set_mctrl() callbacks
to set DLAB, which can cause the earlycon code that intends to access
TX to instead access DLL, leading to missed output and corruption on
the serial line due to unintended modifications to the baud rate.
In particular, for setup() we have:
univ8250_console_setup()
-> serial8250_console_setup()
-> uart_set_options()
-> serial8250_set_termios()
-> serial8250_do_set_termios()
-> serial8250_do_set_divisor()
For config_port() we have:
serial8250_config_port()
-> autoconfig()
For pm() we have:
serial8250_pm()
-> serial8250_do_pm()
-> serial8250_set_sleep()
For set_mctrl() we have (for some devices):
serial8250_set_mctrl()
-> omap8250_set_mctrl()
-> __omap8250_set_mctrl()
To avoid such problems, let's make it so that the console is locked
during pre-registration calls to these callbacks, which will prevent
the earlycon driver from running concurrently.
Remove the partial solution to this problem in the 8250 driver
that locked the console only during autoconfig_irq(), as this would
result in a deadlock with the new approach. The console continues
to be locked during autoconfig_irq() because it can only be called
through uart_configure_port().
Although this patch introduces more locking than strictly necessary
(and in particular it also locks during the call to rs485_config()
which is not affected by this issue as far as I can tell), it follows
the principle that it is the responsibility of the generic console
code to manage the earlycon handoff by ensuring that earlycon and real
console driver code cannot run concurrently, and not the individual
drivers.
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reviewed-by: John Ogness <john.ogness@linutronix.de>
Link: https://linux-review.googlesource.com/id/I7cf8124dcebf8618e6b2ee543fa5b25532de55d8
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240304214350.501253-1-pcc@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7bfb915a59 ]
If the circular buffer is empty, it just means we fit all characters to
send into the HW fifo, but not that the hardware finished transmitting
them.
So if we immediately call stop_tx() after that, this may abort any
pending characters in the HW fifo, and cause dropped characters on the
console.
Fix this by only stopping tx when the tx HW fifo is actually empty.
Fixes: 8275b48b27 ("tty: serial: introduce transmit helpers")
Cc: stable@vger.kernel.org
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Link: https://lore.kernel.org/r/20240303150807.68117-1-jonas.gorski@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6661befe41 ]
As runtime PM is enabled, the module can be runtime
suspended when .remove() is called.
Do a pm_runtime_get_sync() to make sure module is active
before doing any register operations.
Doing a pm_runtime_put_sync() should disable the refclk
so no need to disable it again.
Fixes the below warning at module removel.
[ 39.705310] ------------[ cut here ]------------
[ 39.710004] clk:162:3 already disabled
[ 39.713941] WARNING: CPU: 0 PID: 921 at drivers/clk/clk.c:1090 clk_core_disable+0xb0/0xb8
We called of_platform_populate() in .probe() so call the
cleanup function of_platform_depopulate() in .remove().
Get rid of the now unnnecessary dwc3_ti_remove_core().
Without this, module re-load doesn't work properly.
Fixes: e8784c0aec ("drivers: usb: dwc3: Add AM62 USB wrapper driver")
Cc: stable@vger.kernel.org # v5.19+
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240227-for-v6-9-am62-usb-errata-3-0-v4-1-0ada8ddb0767@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68ca1b49e4 ]
The root inode has a fixed nodeid and generation (1, 0).
Prior to the commit 15db16837a ("fuse: fix illegal access to inode with
reused nodeid") generation number on lookup was ignored. After this commit
lookup with the wrong generation number resulted in the inode being
unhashed. This is correct for non-root inodes, but replacing the root
inode is wrong and results in weird behavior.
Fix by reverting to the old behavior if ignoring the generation for the
root inode, but issuing a warning in dmesg.
Reported-by: Antonio SJ Musumeci <trapexit@spawn.link>
Closes: https://lore.kernel.org/all/CAOQ4uxhek5ytdN8Yz2tNEOg5ea4NkBb4nk0FGPjPk_9nz-VG3g@mail.gmail.com/
Fixes: 15db16837a ("fuse: fix illegal access to inode with reused nodeid")
Cc: <stable@vger.kernel.org> # v5.14
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e7a7681c85 ]
When driver uses pm_runtime_force_suspend() as the system suspend callback
function and registers the wake irq with reverse enable ordering, the wake
irq will be re-enabled when entering system suspend, triggering an
'Unbalanced enable for IRQ xxx' warning. In this scenario, the call
sequence during system suspend is as follows:
suspend_devices_and_enter()
-> dpm_suspend_start()
-> dpm_run_callback()
-> pm_runtime_force_suspend()
-> dev_pm_enable_wake_irq_check()
-> dev_pm_enable_wake_irq_complete()
-> suspend_enter()
-> dpm_suspend_noirq()
-> device_wakeup_arm_wake_irqs()
-> dev_pm_arm_wake_irq()
To fix this issue, complete the setting of WAKE_IRQ_DEDICATED_ENABLED flag
in dev_pm_enable_wake_irq_complete() to avoid redundant irq enablement.
Fixes: 8527beb120 ("PM: sleep: wakeirq: fix wake irq arming")
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Qingliang Li <qingliang.li@mediatek.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Cc: 5.16+ <stable@vger.kernel.org> # 5.16+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e62bf2bfa ]
Linux guests since commit b1c3497e60 ("x86/xen: Add support for
HVMOP_set_evtchn_upcall_vector") in v6.0 onwards will use the per-vCPU
upcall vector when it's advertised in the Xen CPUID leaves.
This upcall is injected through the guest's local APIC as an MSI, unlike
the older system vector which was merely injected by the hypervisor any
time the CPU was able to receive an interrupt and the upcall_pending
flags is set in its vcpu_info.
Effectively, that makes the per-CPU upcall edge triggered instead of
level triggered, which results in the upcall being lost if the MSI is
delivered when the local APIC is *disabled*.
Xen checks the vcpu_info->evtchn_upcall_pending flag when the local APIC
for a vCPU is software enabled (in fact, on any write to the SPIV
register which doesn't disable the APIC). Do the same in KVM since KVM
doesn't provide a way for userspace to intervene and trap accesses to
the SPIV register of a local APIC emulated by KVM.
Fixes: fde0451be8 ("KVM: x86/xen: Support per-vCPU event channel upcall via local APIC")
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Paul Durrant <paul@xen.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240227115648.3104-3-dwmw2@infradead.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a0d9d86849 ]
The radiation meter has the text MGP Instruments PDS-100G or PDS-100GN
produced by Mirion Technologies. Tested by forcing the driver
association with
echo 10c4 863c > /sys/bus/usb-serial/drivers/cp210x/new_id
and then setting the serial port in 115200 8N1 mode. The device
announces ID_USB_VENDOR_ENC=Silicon\x20Labs and ID_USB_MODEL_ENC=PDS100
Signed-off-by: Christian Häggström <christian.haggstrom@orexplore.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3fb7bc4f3a ]
The GMC IR-USB adapter cable utilizes a FTDI FT232R chip.
Add VID/PID for this adapter so it can be used as serial device via
ftdi_sio.
Signed-off-by: Daniel Vogelbacher <daniel@chaospixel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f491356b7 ]
Binutils 2.38 complains about the use of mfpmr when building
ppc6xx_defconfig:
CC arch/powerpc/kernel/pmc.o
{standard input}: Assembler messages:
{standard input}:45: Error: unrecognized opcode: `mfpmr'
{standard input}:56: Error: unrecognized opcode: `mtpmr'
This is because by default the kernel is built with -mcpu=powerpc, and
the mt/mfpmr instructions are not defined.
It can be avoided by enabling CONFIG_E300C3_CPU, but just adding that to
the defconfig will leave open the possibility of randconfig failures.
So add machine directives around the mt/mfpmr instructions to tell
binutils how to assemble them.
Cc: stable@vger.kernel.org
Reported-by: Jan-Benedict Glaw <jbglaw@lug-owl.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20240229122521.762431-3-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9bc4ffd32e ]
psci_init_system_suspend() invokes suspend_set_ops() very early during
bootup even before kernel command line for mem_sleep_default is setup.
This leads to kernel command line mem_sleep_default=s2idle not working
as mem_sleep_current gets changed to deep via suspend_set_ops() and never
changes back to s2idle.
Set mem_sleep_current along with mem_sleep_default during kernel command
line setup as default suspend mode.
Fixes: faf7ec4a92 ("drivers: firmware: psci: add system suspend support")
CC: stable@vger.kernel.org # 5.4+
Signed-off-by: Maulik Shah <quic_mkshah@quicinc.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d394abcb12 ]
Resolving a frequency to an efficient one should not transgress
policy->max (which can be set for thermal reason) and policy->min.
Currently, there is possibility where scaling_cur_freq can exceed
scaling_max_freq when scaling_max_freq is an inefficient frequency.
Add a check to ensure that resolving a frequency will respect
policy->min/max.
Cc: All applicable <stable@vger.kernel.org>
Fixes: 1f39fa0dcc ("cpufreq: Introducing CPUFREQ_RELATION_E")
Signed-off-by: Shivnandan Kumar <quic_kshivnan@quicinc.com>
[ rjw: Whitespace adjustment, changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe2562582b ]
Commit eaae75754d ("docs: turn off "smart quotes" in the HTML build")
disabled conversion of quote marks along with that of dashes.
Despite the short summary, the change affects not only HTML build
but also other build targets including PDF.
However, as "smart quotes" had been enabled for more than half a
decade already, quite a few readers of HTML pages are likely expecting
conversions of "foo" -> “foo” and 'bar' -> ‘bar’.
Furthermore, in LaTeX typesetting convention, it is common to use
distinct marks for opening and closing quote marks.
To satisfy such readers' expectation, restore conversion of quotes
only by setting smartquotes_action [1].
Link: [1] https://www.sphinx-doc.org/en/master/usage/configuration.html#confval-smartquotes_action
Cc: stable@vger.kernel.org # v6.4
Signed-off-by: Akira Yokosawa <akiyks@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20240225094600.65628-1-akiyks@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5b4e4b7203 ]
Some of the registers on the SARADCv2 have bits write protected except
if another bit is set. This is usually done by having the lowest 16 bits
store the data to write and the highest 16 bits specify which of the 16
lowest bits should have their value written to the hardware block.
The write_enable mask for the channel selection was incorrect because it
was just the value shifted by 16 bits, which means it would only ever
write bits and never clear them. So e.g. if someone starts a conversion
on channel 5, the lowest 4 bits would be 0x5, then starts a conversion
on channel 0, it would still be 5.
Instead of shifting the value by 16 as the mask, let's use the OR'ing of
the appropriate masks shifted by 16.
Note that this is not an issue currently because the only SARADCv2
currently supported has a reset defined in its Device Tree, that reset
resets the SARADC controller before starting a conversion on a channel.
However, this reset is handled as optional by the probe function and
thus proper masking should be used in the event an SARADCv2 without a
reset ever makes it upstream.
Fixes: 757953f8ec ("iio: adc: rockchip_saradc: Add support for RK3588")
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20240223-saradcv2-chan-mask-v1-2-84b06a0f623a@theobroma-systems.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dfd2bf4367 ]
In raid5_cache_count():
if (conf->max_nr_stripes < conf->min_nr_stripes)
return 0;
return conf->max_nr_stripes - conf->min_nr_stripes;
The current check is ineffective, as the values could change immediately
after being checked.
In raid5_set_cache_size():
...
conf->min_nr_stripes = size;
...
while (size > conf->max_nr_stripes)
conf->min_nr_stripes = conf->max_nr_stripes;
...
Due to intermediate value updates in raid5_set_cache_size(), concurrent
execution of raid5_cache_count() and raid5_set_cache_size() may lead to
inconsistent reads of conf->max_nr_stripes and conf->min_nr_stripes.
The current checks are ineffective as values could change immediately
after being checked, raising the risk of conf->min_nr_stripes exceeding
conf->max_nr_stripes and potentially causing an integer overflow.
This possible bug is found by an experimental static analysis tool
developed by our team. This tool analyzes the locking APIs to extract
function pairs that can be concurrently executed, and then analyzes the
instructions in the paired functions to identify possible concurrency bugs
including data races and atomicity violations. The above possible bug is
reported when our tool analyzes the source code of Linux 6.2.
To resolve this issue, it is suggested to introduce local variables
'min_stripes' and 'max_stripes' in raid5_cache_count() to ensure the
values remain stable throughout the check. Adding locks in
raid5_cache_count() fails to resolve atomicity violations, as
raid5_set_cache_size() may hold intermediate values of
conf->min_nr_stripes while unlocked. With this patch applied, our tool no
longer reports the bug, with the kernel configuration allyesconfig for
x86_64. Due to the lack of associated hardware, we cannot test the patch
in runtime testing, and just verify it according to the code logic.
Fixes: edbe83ab4c ("md/raid5: allow the stripe_cache to grow and shrink.")
Cc: stable@vger.kernel.org
Signed-off-by: Gui-Dong Han <2045gemini@gmail.com>
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20240112071017.16313-1-2045gemini@gmail.com
Signed-off-by: Song Liu <song@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0568b6f0d8 ]
IPv6 checksum tests with unaligned addresses on 64-bit builds result
in unexpected failures.
Expected expected == csum_result, but
expected == 46591 (0xb5ff)
csum_result == 46381 (0xb52d)
with alignment offset 1
Oddly enough, the problem disappeared after adding test code into
the beginning of csum_ipv6_magic().
As it turns out, the 'sum' parameter of csum_ipv6_magic() is declared as
__wsum, which is a 32-bit variable. However, it is treated as 64-bit
variable in the 64-bit assembler code. Tests showed that the upper 32 bit
of the register used to pass the variable are _not_ cleared when entering
the function. This can result in checksum calculation errors.
Clearing the upper 32 bit of 'sum' as first operation in the assembler
code fixes the problem.
Acked-by: Helge Deller <deller@gmx.de>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b75b12d70 ]
hppa 64-bit systems calculates the IPv6 checksum using 64-bit add
operations. The last add folds protocol and length fields into the 64-bit
result. While unlikely, this operation can overflow. The overflow can be
triggered with a code sequence such as the following.
/* try to trigger massive overflows */
memset(tmp_buf, 0xff, sizeof(struct in6_addr));
csum_result = csum_ipv6_magic((struct in6_addr *)tmp_buf,
(struct in6_addr *)tmp_buf,
0xffff, 0xff, 0xffffffff);
Fix the problem by adding any overflows from the final add operation into
the calculated checksum. Fortunately, we can do this without additional
cost by replacing the add operation used to fold the checksum into 32 bit
with "add,dc" to add in the missing carry.
Cc: Palmer Dabbelt <palmer@rivosinc.com>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Charlie Jenkins <charlie@rivosinc.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4408ba75e4 ]
Calculating the IPv6 checksum on 32-bit systems missed overflows when
adding the proto+len fields into the checksum. This results in the
following unit test failure.
# test_csum_ipv6_magic: ASSERTION FAILED at lib/checksum_kunit.c:506
Expected ( u64)csum_result == ( u64)expected, but
( u64)csum_result == 46722 (0xb682)
( u64)expected == 46721 (0xb681)
not ok 5 test_csum_ipv6_magic
This is probably rarely seen in the real world because proto+len are
usually small values which will rarely result in overflows when calculating
the checksum. However, the unit test code uses large values for the length
field, causing the test to fail.
Fix the problem by adding the missing carry into the final checksum.
Cc: Palmer Dabbelt <palmer@rivosinc.com>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Charlie Jenkins <charlie@rivosinc.com>
Reviewed-by: Charlie Jenkins <charlie@rivosinc.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a2abae8f0b ]
IP checksum unit tests report the following error when run on hppa/hppa64.
# test_ip_fast_csum: ASSERTION FAILED at lib/checksum_kunit.c:463
Expected ( u64)csum_result == ( u64)expected, but
( u64)csum_result == 33754 (0x83da)
( u64)expected == 10946 (0x2ac2)
not ok 4 test_ip_fast_csum
0x83da is the expected result if the IP header length is 20 bytes. 0x2ac2
is the expected result if the IP header length is 24 bytes. The test fails
with an IP header length of 24 bytes. It appears that ip_fast_csum()
always returns the checksum for a 20-byte header, no matter how long
the header actually is.
Code analysis shows a suspicious assembler sequence in ip_fast_csum().
" addc %0, %3, %0\n"
"1: ldws,ma 4(%1), %3\n"
" addib,< 0, %2, 1b\n" <---
While my understanding of HPPA assembler is limited, it does not seem
to make much sense to subtract 0 from a register and to expect the result
to ever be negative. Subtracting 1 from the length parameter makes more
sense. On top of that, the operation should be repeated if and only if
the result is still > 0, so change the suspicious instruction to
" addib,> -1, %2, 1b\n"
The IP checksum unit test passes after this change.
Cc: Palmer Dabbelt <palmer@rivosinc.com>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Charlie Jenkins <charlie@rivosinc.com>
Reviewed-by: Charlie Jenkins <charlie@rivosinc.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5db6a7457 ]
Convert to use real temp variables instead of clobbering processor
registers. This aligns the 64-bit inline assembly code with the 32-bit
assembly code which was rewritten with commit 427c1073a2
("parisc/unaligned: Rewrite 32-bit inline assembly of emulate_ldd()").
While at it, fix comment in 32-bit rewrite code. Temporary variables are
now used for both 32-bit and 64-bit code, so move their declarations
to the function header.
No functional change intended.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org # v6.0+
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d54e56f31a ]
Commit 344da544f1 ("x86/nmi: Print reasons why backtrace NMIs are
ignored") creates a super nice framework to diagnose NMIs.
Every time nmi_exc() is called, it increments a per_cpu counter
(nsp->idt_nmi_seq). At its exit, it also increments the same counter. By
reading this counter it can be seen how many times that function was called
(dividing by 2), and, if the function is still being executed, by checking
the idt_nmi_seq's least significant bit.
On the check side (nmi_backtrace_stall_check()), that variable is queried
to check if the NMI is still being executed, but, there is a mistake in the
bitwise operation. That code wants to check if the least significant bit of
the idt_nmi_seq is set or not, but does the opposite, and checks for all
the other bits, which will always be true after the first exc_nmi()
executed successfully.
This appends the misleading string to the dump "(CPU currently in NMI
handler function)"
Fix it by checking the least significant bit, and if it is set, append the
string.
Fixes: 344da544f1 ("x86/nmi: Print reasons why backtrace NMIs are ignored")
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Paul E. McKenney <paulmck@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240207165237.1048837-1-leitao@debian.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ecbd8ebb51 ]
Commit d7038f9518 ("md-bitmap: don't use ->index for pages backing the
bitmap file") removed page->index from bitmap code, but left wrong code
logic for clustered-md. current code never set slot offset for cluster
nodes, will sometimes cause crash in clustered env.
Call trace (partly):
md_bitmap_file_set_bit+0x110/0x1d8 [md_mod]
md_bitmap_startwrite+0x13c/0x240 [md_mod]
raid1_make_request+0x6b0/0x1c08 [raid1]
md_handle_request+0x1dc/0x368 [md_mod]
md_submit_bio+0x80/0xf8 [md_mod]
__submit_bio+0x178/0x300
submit_bio_noacct_nocheck+0x11c/0x338
submit_bio_noacct+0x134/0x614
submit_bio+0x28/0xdc
submit_bh_wbc+0x130/0x1cc
submit_bh+0x1c/0x28
Fixes: d7038f9518 ("md-bitmap: don't use ->index for pages backing the bitmap file")
Cc: stable@vger.kernel.org # v6.6+
Signed-off-by: Heming Zhao <heming.zhao@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20240223121128.28985-1-heming.zhao@suse.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f174ae4f3 ]
Now that the calculation of fastmap size in ubi_calc_fm_size() is
incorrect since it miss each user volume's ubi_fm_eba structure and the
Internal UBI volume info. Let's correct the calculation.
Cc: stable@vger.kernel.org
Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 723012cab7 ]
Page cache reads are lockless, so setting the freshly allocated page
uptodate before we've overwritten it with the data it's supposed to have
in it will allow a simultaneous reader to see old data. Move the call
to SetPageUptodate into ubifs_write_end(), which is after we copied the
new data into the page.
Fixes: 1e51764a3c ("UBIFS: add new flash file system")
Cc: stable@vger.kernel.org
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9511176bba ]
There were multiple issues with direct_io_allow_mmap:
- fuse_link_write_file() was missing, resulting in warnings in
fuse_write_file_get() and EIO from msync()
- "vma->vm_ops = &fuse_file_vm_ops" was not set, but especially
fuse_page_mkwrite is needed.
The semantics of invalidate_inode_pages2() is so far not clearly defined in
fuse_file_mmap. It dates back to commit 3121bfe763 ("fuse: fix
"direct_io" private mmap") Though, as direct_io_allow_mmap is a new
feature, that was for MAP_PRIVATE only. As invalidate_inode_pages2() is
calling into fuse_launder_folio() and writes out dirty pages, it should be
safe to call invalidate_inode_pages2 for MAP_PRIVATE and MAP_SHARED as
well.
Cc: Hao Xu <howeyxu@tencent.com>
Cc: stable@vger.kernel.org
Fixes: e78662e818 ("fuse: add a new fuse init flag to relax restrictions in no cache mode")
Signed-off-by: Bernd Schubert <bschubert@ddn.com>
Reviewed-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e10aea105e ]
The out-of-bounds test allocates an object that is three bytes too short
in order to validate the bounds checking. Starting with gcc-14, this
causes a compile-time warning as gcc has grown smart enough to understand
the sizeof() logic:
mm/kasan/kasan_test.c: In function 'kmalloc_oob_16':
mm/kasan/kasan_test.c:443:14: error: allocation of insufficient size '13' for type 'struct <anonymous>' with size '16' [-Werror=alloc-size]
443 | ptr1 = kmalloc(sizeof(*ptr1) - 3, GFP_KERNEL);
| ^
Hide the actual computation behind a RELOC_HIDE() that ensures
the compiler misses the intentional bug.
Link: https://lkml.kernel.org/r/20240212111609.869266-1-arnd@kernel.org
Fixes: 3f15801cdc ("lib: add kasan test module")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Andrey Konovalov <andreyknvl@gmail.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Marco Elver <elver@google.com>
Cc: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8f6f88d25 ]
Device mapper may create a non-zoned mapped device out of a zoned device
(e.g., the dm-zoned target). In such case, some queue limit such as the
max_zone_append_sectors and zone_write_granularity endup being non zero
values for a block device that is not zoned. Avoid this by clearing
these limits in blk_stack_limits() when the stacked zoned limit is
false.
Fixes: 3093a47972 ("block: inherit the zoned characteristics in blk_stack_limits")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240222131724.1803520-1-dlemoal@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4fbf8bc733 ]
When yangerkun review commit 93cdf49f6e ("ext4: Fix best extent lstart
adjustment logic in ext4_mb_new_inode_pa()"), it was found that the best
extent did not completely cover the original request after adjusting the
best extent lstart in ext4_mb_new_inode_pa() as follows:
original request: 2/10(8)
normalized request: 0/64(64)
best extent: 0/9(9)
When we check if best ex can be kept at start of goal, ac_o_ex.fe_logical
is 2 less than the adjusted best extent logical end 9, so we think the
adjustment is done. But obviously 0/9(9) doesn't cover 2/10(8), so we
should determine here if the original request logical end is less than or
equal to the adjusted best extent logical end.
In addition, add a comment stating when adjusted best_ex will not cover
the original request, and remove the duplicate assertion because adjusting
lstart makes no change to b_ex.fe_len.
Link: https://lore.kernel.org/r/3630fa7f-b432-7afd-5f79-781bc3b2c5ea@huawei.com
Fixes: 93cdf49f6e ("ext4: Fix best extent lstart adjustment logic in ext4_mb_new_inode_pa()")
Cc: <stable@kernel.org>
Signed-off-by: yangerkun <yangerkun@huawei.com>
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Ojaswin Mujoo <ojaswin@linux.ibm.com>
Link: https://lore.kernel.org/r/20240201141845.1879253-1-libaokun1@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 85506aca2e ]
While mq_perf_tests runs with the default kselftest timeout limit, which
is 45 seconds, the test takes about 60 seconds to complete on i3.metal
AWS instances. Hence, the test always times out. Increase the timeout
to 180 seconds.
Fixes: 852c8cbf34 ("selftests/kselftest/runner.sh: Add 45 second timeout per test")
Cc: <stable@vger.kernel.org> # 5.4.x
Signed-off-by: SeongJae Park <sj@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7d42e09760 ]
During the PCI AER system's error recovery process, the kernel driver
may encounter a race condition with freeing the reset_data structure's
memory. If the device restart will take more than 10 seconds the function
scheduling that restart will exit due to a timeout, and the reset_data
structure will be freed. However, this data structure is used for
completion notification after the restart is completed, which leads
to a UAF bug.
This results in a KFENCE bug notice.
BUG: KFENCE: use-after-free read in adf_device_reset_worker+0x38/0xa0 [intel_qat]
Use-after-free read at 0x00000000bc56fddf (in kfence-#142):
adf_device_reset_worker+0x38/0xa0 [intel_qat]
process_one_work+0x173/0x340
To resolve this race condition, the memory associated to the container
of the work_struct is freed on the worker if the timeout expired,
otherwise on the function that schedules the worker.
The timeout detection can be done by checking if the caller is
still waiting for completion or not by using completion_done() function.
Fixes: d8cba25d2c ("crypto: qat - Intel(R) QAT driver framework")
Cc: <stable@vger.kernel.org>
Signed-off-by: Damian Muszynski <damian.muszynski@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 903eb9fb85 ]
Only domain root packages can enumerate System (Psys) domain.
Whether a package is domain root or not is described in the Bit 0 of the
Domain Info register.
Add support for Domain Info register and fix the System domain probing
accordingly.
Fixes: 9eef7f9da9 ("powercap: intel_rapl: Introduce RAPL TPMI interface driver")
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Cc: 6.5+ <stable@vger.kernel.org> # 6.5+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit faa9130ce7 ]
Add the missing Domain Info register. This also fixes the bogus
definition of the Interrupt register.
Neither of these two registers was used previously.
Fixes: 9eef7f9da9 ("powercap: intel_rapl: Introduce RAPL TPMI interface driver")
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Cc: 6.5+ <stable@vger.kernel.org> # 6.5+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1aa09b9379 ]
The RAPL framework uses CPU hotplug locking to protect the rapl_packages
list and rp->lead_cpu to guarantee that
1. the RAPL package device is not unprobed and freed
2. the cached rp->lead_cpu is always valid
for operations like powercap sysfs accesses.
Current RAPL APIs assume being called from CPU hotplug callbacks which
hold the CPU hotplug lock, but TPMI RAPL driver invokes the APIs in the
driver's .probe() function without acquiring the CPU hotplug lock.
Fix the problem by providing both locked and lockless versions of RAPL
APIs.
Fixes: 9eef7f9da9 ("powercap: intel_rapl: Introduce RAPL TPMI interface driver")
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Cc: 6.5+ <stable@vger.kernel.org> # 6.5+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d1f5006ff ]
A NULL pointer dereference is triggered when probing the MMIO RAPL
driver on platforms with CPU ID not listed in intel_rapl_common CPU
model list.
This is because the intel_rapl_common module still probes on such
platforms even if 'defaults_msr' is not set after commit 1488ac990a
("powercap: intel_rapl: Allow probing without CPUID match"). Thus the
MMIO RAPL rp->priv->defaults is NULL when registering to RAPL framework.
Fix the problem by adding sanity check to ensure rp->priv->rapl_defaults
is always valid.
Fixes: 1488ac990a ("powercap: intel_rapl: Allow probing without CPUID match")
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Cc: 6.5+ <stable@vger.kernel.org> # 6.5+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7251b9e8a0 ]
CPU temperature can be negative in some cases. Thus the negative CPU
temperature should not be considered as a failure.
Fix intel_tcc_get_temp() and its users to support negative CPU
temperature.
Fixes: a3c1f066e1 ("thermal/intel: Introduce Intel TCC library")
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Cc: 6.3+ <stable@vger.kernel.org> # 6.3+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d75b8aa5c ]
Always flush the per-vCPU async #PF workqueue when a vCPU is clearing its
completion queue, e.g. when a VM and all its vCPUs is being destroyed.
KVM must ensure that none of its workqueue callbacks is running when the
last reference to the KVM _module_ is put. Gifting a reference to the
associated VM prevents the workqueue callback from dereferencing freed
vCPU/VM memory, but does not prevent the KVM module from being unloaded
before the callback completes.
Drop the misguided VM refcount gifting, as calling kvm_put_kvm() from
async_pf_execute() if kvm_put_kvm() flushes the async #PF workqueue will
result in deadlock. async_pf_execute() can't return until kvm_put_kvm()
finishes, and kvm_put_kvm() can't return until async_pf_execute() finishes:
WARNING: CPU: 8 PID: 251 at virt/kvm/kvm_main.c:1435 kvm_put_kvm+0x2d/0x320 [kvm]
Modules linked in: vhost_net vhost vhost_iotlb tap kvm_intel kvm irqbypass
CPU: 8 PID: 251 Comm: kworker/8:1 Tainted: G W 6.6.0-rc1-e7af8d17224a-x86/gmem-vm #119
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
Workqueue: events async_pf_execute [kvm]
RIP: 0010:kvm_put_kvm+0x2d/0x320 [kvm]
Call Trace:
<TASK>
async_pf_execute+0x198/0x260 [kvm]
process_one_work+0x145/0x2d0
worker_thread+0x27e/0x3a0
kthread+0xba/0xe0
ret_from_fork+0x2d/0x50
ret_from_fork_asm+0x11/0x20
</TASK>
---[ end trace 0000000000000000 ]---
INFO: task kworker/8:1:251 blocked for more than 120 seconds.
Tainted: G W 6.6.0-rc1-e7af8d17224a-x86/gmem-vm #119
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:kworker/8:1 state:D stack:0 pid:251 ppid:2 flags:0x00004000
Workqueue: events async_pf_execute [kvm]
Call Trace:
<TASK>
__schedule+0x33f/0xa40
schedule+0x53/0xc0
schedule_timeout+0x12a/0x140
__wait_for_common+0x8d/0x1d0
__flush_work.isra.0+0x19f/0x2c0
kvm_clear_async_pf_completion_queue+0x129/0x190 [kvm]
kvm_arch_destroy_vm+0x78/0x1b0 [kvm]
kvm_put_kvm+0x1c1/0x320 [kvm]
async_pf_execute+0x198/0x260 [kvm]
process_one_work+0x145/0x2d0
worker_thread+0x27e/0x3a0
kthread+0xba/0xe0
ret_from_fork+0x2d/0x50
ret_from_fork_asm+0x11/0x20
</TASK>
If kvm_clear_async_pf_completion_queue() actually flushes the workqueue,
then there's no need to gift async_pf_execute() a reference because all
invocations of async_pf_execute() will be forced to complete before the
vCPU and its VM are destroyed/freed. And that in turn fixes the module
unloading bug as __fput() won't do module_put() on the last vCPU reference
until the vCPU has been freed, e.g. if closing the vCPU file also puts the
last reference to the KVM module.
Note that kvm_check_async_pf_completion() may also take the work item off
the completion queue and so also needs to flush the work queue, as the
work will not be seen by kvm_clear_async_pf_completion_queue(). Waiting
on the workqueue could theoretically delay a vCPU due to waiting for the
work to complete, but that's a very, very small chance, and likely a very
small delay. kvm_arch_async_page_present_queued() unconditionally makes a
new request, i.e. will effectively delay entering the guest, so the
remaining work is really just:
trace_kvm_async_pf_completed(addr, cr2_or_gpa);
__kvm_vcpu_wake_up(vcpu);
mmput(mm);
and mmput() can't drop the last reference to the page tables if the vCPU is
still alive, i.e. the vCPU won't get stuck tearing down page tables.
Add a helper to do the flushing, specifically to deal with "wakeup all"
work items, as they aren't actually work items, i.e. are never placed in a
workqueue. Trying to flush a bogus workqueue entry rightly makes
__flush_work() complain (kudos to whoever added that sanity check).
Note, commit 5f6de5cbeb ("KVM: Prevent module exit until all VMs are
freed") *tried* to fix the module refcounting issue by having VMs grab a
reference to the module, but that only made the bug slightly harder to hit
as it gave async_pf_execute() a bit more time to complete before the KVM
module could be unloaded.
Fixes: af585b921e ("KVM: Halt vcpu if page it tries to access is swapped out")
Cc: stable@vger.kernel.org
Cc: David Matlack <dmatlack@google.com>
Reviewed-by: Xu Yilun <yilun.xu@intel.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Link: https://lore.kernel.org/r/20240110011533.503302-2-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b71021b2e ]
All the sink pads of the crossbar switch require an active link if
they're part of the pipeline. Mark them with the
MEDIA_PAD_FL_MUST_CONNECT flag to fail pipeline validation if they're
not connected. This allows removing a manual check when translating
streams.
Cc: stable@vger.kernel.org # 6.1
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3decc5ce7 ]
The MEDIA_PAD_FL_MUST_CONNECT flag indicates that the pad requires an
enabled link to stream, but only if it has any link at all. This makes
little sense, as if a pad is part of a pipeline, there are very few use
cases for an active link to be mandatory only if links exist at all. A
review of in-tree drivers confirms they all need an enabled link for
pads marked with the MEDIA_PAD_FL_MUST_CONNECT flag.
Expand the scope of the flag by rejecting pads that have no links at
all. This requires modifying the pipeline build code to add those pads
to the pipeline.
Cc: stable@vger.kernel.org # 6.1
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ec9109cf9 ]
The pad local variable in the media_pipeline_explore_next_link()
function is used to store the pad through which the entity has been
reached. Rename it to origin to reflect that and make the code easier to
read. This will be even more important in subsequent commits when
expanding the function with additional logic.
Cc: stable@vger.kernel.org # 6.1
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 422f7af75d ]
The media_create_pad_link() function doesn't correctly clear reject link
type flags, nor does it set the DATA_LINK flag. It only works because
the MEDIA_LNK_FL_DATA_LINK flag's value is 0.
Fix it by returning an error if any link type flag is set. This doesn't
introduce any regression, as nobody calls the media_create_pad_link()
function with link type flags (easily checked by grepping for the flag
in the source code, there are very few hits).
Set the MEDIA_LNK_FL_DATA_LINK explicitly, which is a no-op that the
compiler will optimize out, but is still useful to make the code more
explicit and easier to understand.
Cc: stable@vger.kernel.org # 6.1
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78f0daa026 ]
When building pipelines by following links, the
media_pipeline_explore_next_link() function only traverses enabled
links. The remote pad of a disabled link is not added to the pipeline,
and neither is the local pad. While the former is correct as disabled
links should not be followed, not adding the local pad breaks processing
of the MEDIA_PAD_FL_MUST_CONNECT flag.
The MEDIA_PAD_FL_MUST_CONNECT flag is checked in the
__media_pipeline_start() function that iterates over all pads after
populating the pipeline. If the pad is not present, the check gets
skipped, rendering it useless.
Fix this by adding the local pad of all links regardless of their state,
only skipping the remote pad for disabled links.
Cc: stable@vger.kernel.org # 6.1
Fixes: ae21987283 ("media: mc: entity: Rewrite media_pipeline_start()")
Reported-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Closes: https://lore.kernel.org/linux-media/7658a15a-80c5-219f-2477-2a94ba6c6ba1@kontron.de
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 36d503ad54 ]
In xc4000_get_frequency():
*freq = priv->freq_hz + priv->freq_offset;
The code accesses priv->freq_hz and priv->freq_offset without holding any
lock.
In xc4000_set_params():
// Code that updates priv->freq_hz and priv->freq_offset
...
xc4000_get_frequency() and xc4000_set_params() may execute concurrently,
risking inconsistent reads of priv->freq_hz and priv->freq_offset. Since
these related data may update during reading, it can result in incorrect
frequency calculation, leading to atomicity violations.
This possible bug is found by an experimental static analysis tool
developed by our team, BassCheck[1]. This tool analyzes the locking APIs
to extract function pairs that can be concurrently executed, and then
analyzes the instructions in the paired functions to identify possible
concurrency bugs including data races and atomicity violations. The above
possible bug is reported when our tool analyzes the source code of
Linux 6.2.
To address this issue, it is proposed to add a mutex lock pair in
xc4000_get_frequency() to ensure atomicity. With this patch applied, our
tool no longer reports the possible bug, with the kernel configuration
allyesconfig for x86_64. Due to the lack of associated hardware, we cannot
test the patch in runtime testing, and just verify it according to the
code logic.
[1] https://sites.google.com/view/basscheck/
Fixes: 4c07e32884 ("[media] xc4000: Fix get_frequency()")
Cc: stable@vger.kernel.org
Reported-by: BassCheck <bass@buaa.edu.cn>
Signed-off-by: Gui-Dong Han <2045gemini@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a9e8a7159 ]
The cleanup can be dispatched while the atomic update is still active,
which means that the memory acquired in the atomic update needs to
not be invalidated by the cleanup. The buffer objects in vmw_plane_state
instead of using the builtin map_and_cache were trying to handle
the lifetime of the mapped memory themselves, leading to crashes.
Use the map_and_cache instead of trying to manage the lifetime of the
buffer objects held by the vmw_plane_state.
Fixes kernel oops'es in IGT's kms_cursor_legacy forked-bo.
Signed-off-by: Zack Rusin <zack.rusin@broadcom.com>
Fixes: bb6780aa5a ("drm/vmwgfx: Diff cursors when using cmds")
Cc: <stable@vger.kernel.org> # v6.2+
Reviewed-by: Martin Krastev <martin.krastev@broadcom.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240126200804.732454-6-zack.rusin@broadcom.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d27056c24 ]
When trying to instantiate a max14830 device from userspace:
echo max14830 0x60 > /sys/bus/i2c/devices/i2c-2/new_device
we get the following error:
Unable to handle kernel NULL pointer dereference at virtual address...
...
Call trace:
max310x_i2c_probe+0x48/0x170 [max310x]
i2c_device_probe+0x150/0x2a0
...
Add check for validity of devtype to prevent the error, and abort probe
with a meaningful error message.
Fixes: 2e1f2d9a9b ("serial: max310x: implement I2C support")
Cc: stable@vger.kernel.org
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240118152213.2644269-2-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac02f007d6 ]
If the SMACK64TRANSMUTE xattr is provided, and the inode is a directory,
update the in-memory inode flags by setting SMK_INODE_TRANSMUTE.
Cc: stable@vger.kernel.org
Fixes: 5c6d1125f8 ("Smack: Transmute labels on specified directories") # v2.6.38.x
Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b327c72753 ]
Recovery remote processor failed when wdg irq received:
[ 0.842574] remoteproc remoteproc0: crash detected in cix-dsp-rproc: type watchdog
[ 0.842750] remoteproc remoteproc0: handling crash #1 in cix-dsp-rproc
[ 0.842824] remoteproc remoteproc0: recovering cix-dsp-rproc
[ 0.843342] remoteproc remoteproc0: stopped remote processor cix-dsp-rproc
[ 0.847901] rproc-virtio rproc-virtio.0.auto: Failed to associate buffer
[ 0.847979] remoteproc remoteproc0: failed to probe subdevices for cix-dsp-rproc: -16
The reason is that dma coherent mem would not be released when
recovering the remote processor, due to rproc_virtio_remove()
would not be called, where the mem released. It will fail when
it try to allocate and associate buffer again.
Releasing reserved memory from rproc_virtio_dev_release(), instead of
rproc_virtio_remove().
Fixes: 1d7b61c06d ("remoteproc: virtio: Create platform device for the remoteproc_virtio")
Signed-off-by: Joakim Zhang <joakim.zhang@cixtech.com>
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231217053659.3245745-1-joakim.zhang@cixtech.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87318b7092 ]
The imgu driver fails to probe with the following message because it
does not set the pad's flags before calling media_entity_pads_init().
[ 14.596315] ipu3-imgu 0000:00:05.0: failed initialize subdev media entity (-22)
[ 14.596322] ipu3-imgu 0000:00:05.0: failed to register subdev0 ret (-22)
[ 14.596327] ipu3-imgu 0000:00:05.0: failed to register pipes (-22)
[ 14.596331] ipu3-imgu 0000:00:05.0: failed to create V4L2 devices (-22)
Fix the initialization order so that the driver probe succeeds. The ops
initialization is also moved together for readability.
Fixes: a0ca1627b4 ("media: staging/intel-ipu3: Add v4l2 driver based on media framework")
Cc: <stable@vger.kernel.org> # 6.7
Cc: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Hidenori Kobayashi <hidenorik@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f7352557a ]
This is the candidate patch of CVE-2023-47233 :
https://nvd.nist.gov/vuln/detail/CVE-2023-47233
In brcm80211 driver,it starts with the following invoking chain
to start init a timeout worker:
->brcmf_usb_probe
->brcmf_usb_probe_cb
->brcmf_attach
->brcmf_bus_started
->brcmf_cfg80211_attach
->wl_init_priv
->brcmf_init_escan
->INIT_WORK(&cfg->escan_timeout_work,
brcmf_cfg80211_escan_timeout_worker);
If we disconnect the USB by hotplug, it will call
brcmf_usb_disconnect to make cleanup. The invoking chain is :
brcmf_usb_disconnect
->brcmf_usb_disconnect_cb
->brcmf_detach
->brcmf_cfg80211_detach
->kfree(cfg);
While the timeout woker may still be running. This will cause
a use-after-free bug on cfg in brcmf_cfg80211_escan_timeout_worker.
Fix it by deleting the timer and canceling the worker in
brcmf_cfg80211_detach.
Fixes: e756af5b30 ("brcmfmac: add e-scan support.")
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Cc: stable@vger.kernel.org
[arend.vanspriel@broadcom.com: keep timer delete as is and cancel work just before free]
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240107072504.392713-1-arend.vanspriel@broadcom.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 80c883db87 upstream.
Use a switch statement with macro-generated case statements to handle
translating feature flags in order to reduce the probability of runtime
errors due to copy+paste goofs, to make compile-time errors easier to
debug, and to make the code more readable.
E.g. the compiler won't directly generate an error for duplicate if
statements
if (x86_feature == X86_FEATURE_SGX1)
return KVM_X86_FEATURE_SGX1;
else if (x86_feature == X86_FEATURE_SGX2)
return KVM_X86_FEATURE_SGX1;
and so instead reverse_cpuid_check() will fail due to the untranslated
entry pointing at a Linux-defined leaf, which provides practically no
hint as to what is broken
arch/x86/kvm/reverse_cpuid.h:108:2: error: call to __compiletime_assert_450 declared with 'error' attribute:
BUILD_BUG_ON failed: x86_leaf == CPUID_LNX_4
BUILD_BUG_ON(x86_leaf == CPUID_LNX_4);
^
whereas duplicate case statements very explicitly point at the offending
code:
arch/x86/kvm/reverse_cpuid.h:125:2: error: duplicate case value '361'
KVM_X86_TRANSLATE_FEATURE(SGX2);
^
arch/x86/kvm/reverse_cpuid.h:124:2: error: duplicate case value '360'
KVM_X86_TRANSLATE_FEATURE(SGX1);
^
And without macros, the opposite type of copy+paste goof doesn't generate
any error at compile-time, e.g. this yields no complaints:
case X86_FEATURE_SGX1:
return KVM_X86_FEATURE_SGX1;
case X86_FEATURE_SGX2:
return KVM_X86_FEATURE_SGX1;
Note, __feature_translate() is forcibly inlined and the feature is known
at compile-time, so the code generation between an if-elif sequence and a
switch statement should be identical.
Signed-off-by: Jim Mattson <jmattson@google.com>
Link: https://lore.kernel.org/r/20231024001636.890236-2-jmattson@google.com
[sean: use a macro, rewrite changelog]
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eefe5e6682 upstream.
The low five bits {INTEL_PSFD, IPRED_CTRL, RRSBA_CTRL, DDPD_U, BHI_CTRL}
advertise the availability of specific bits in IA32_SPEC_CTRL. Since KVM
dynamically determines the legal IA32_SPEC_CTRL bits for the underlying
hardware, the hard work has already been done. Just let userspace know
that a guest can use these IA32_SPEC_CTRL bits.
The sixth bit (MCDT_NO) states that the processor does not exhibit MXCSR
Configuration Dependent Timing (MCDT) behavior. This is an inherent
property of the physical processor that is inherited by the virtual
CPU. Pass that information on to userspace.
Signed-off-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Chao Gao <chao.gao@intel.com>
Link: https://lore.kernel.org/r/20231024001636.890236-1-jmattson@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Newer versions of the DesignWare I2C block support the detection of
stuck signals, and a mechanism to recover from them. Add the required
software support to the driver.
This change was prompted by the observation that reading a single byte
from register 0 of a VEML7700 seems to cause it to issue an ACK too
early, and the controller to complain about losing arbitration. There
is a suspicion that this may be a more widespread problem, but at least
this patch prevents the bus from locking up.
See: https://github.com/raspberrypi/linux/issues/6057
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The spec allows for up to two 512-byte pages to be allocated for the
Extension Register General Info block, so allocate accordingly.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Don't attempt to turn on CQ if the other mandatory features are not
indicated as supported by the card. Also make sure that the register write
actually stuck, as some cards claim support but never report back that
the queue engine is enabled.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Certain status bits in these registers may need polling outside of
SD-specific code. Export in sd_ops.h
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
The eMMC spec says that in certain circumstances the controller can't
respond to a halt request - in practice, this occurs if a CMD
timeout happens (card went away/crashed).
Clear the halt request by writing 0 to CQHCI_CTL. Also fix a logic error
testing for halt in cqhci_request.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
[ Upstream commit df7ecce842 ]
Clearing BSS should only be done once, at the very beginning.
efi_pe_entry() is the entrypoint from the firmware, which may not clear
BSS and so it is done explicitly. However, efi_pe_entry() is also used
as an entrypoint by the mixed mode startup code, in which case BSS will
already have been cleared, and doing it again at this point will corrupt
global variables holding the firmware's GDT/IDT and segment selectors.
So make the memset() conditional on whether the EFI stub is running in
native mode.
Fixes: b3810c5a2c ("x86/efistub: Clear decompressor BSS in native EFI entrypoint")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3810c5a2c ]
The EFI stub on x86 no longer invokes the decompressor as a subsequent
boot stage, but calls into the decompression code directly while running
in the context of the EFI boot services.
This means that when using the native EFI entrypoint (as opposed to the
EFI handover protocol, which clears BSS explicitly), the firmware PE
image loader is being relied upon to ensure that BSS is zeroed before
the EFI stub is entered from the firmware.
As Radek's report proves, this is a bad idea. Not all loaders do this
correctly, which means some global variables that should be statically
initialized to 0x0 may have junk in them.
So clear BSS explicitly when entering via efi_pe_entry(). Note that
zeroing BSS from C code is not generally safe, but in this case, the
following assignment and dereference of a global pointer variable
ensures that the memset() cannot be deferred or reordered.
Cc: <stable@kernel.org> # v6.1+
Reported-by: Radek Podgorny <radek@podgorny.cz>
Closes: https://lore.kernel.org/all/a99a831a-8ad5-4cb0-bff9-be637311f771@podgorny.cz
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b4d78cfeb3 ]
It is possible to set up dm-integrity with smaller sector size than
the logical sector size of the underlying device. In this situation,
dm-integrity guarantees that the outgoing bios have the same alignment as
incoming bios (so, if you create a filesystem with 4k block size,
dm-integrity would send 4k-aligned bios to the underlying device).
This guarantee was broken when integrity_recheck was implemented.
integrity_recheck sends bio that is aligned to ic->sectors_per_block. So
if we set up integrity with 512-byte sector size on a device with logical
block size 4k, we would be sending unaligned bio. This triggered a bug in
one of our internal tests.
This commit fixes it by determining the actual alignment of the
incoming bio and then makes sure that the outgoing bio in
integrity_recheck has the same alignment.
Fixes: c88f5e553f ("dm-integrity: recheck the integrity tag after a failure")
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e5f0f6383 ]
Some IO will dispatch from kworker with different io_context settings
than the submitting task, we may need to specify a priority to avoid
losing priority.
Add IO priority parameter to dm_io() and update all callers.
Co-developed-by: Yibin Ding <yibin.ding@unisoc.com>
Signed-off-by: Yibin Ding <yibin.ding@unisoc.com>
Signed-off-by: Hongyu Jin <hongyu.jin@unisoc.com>
Reviewed-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Stable-dep-of: b4d78cfeb3 ("dm-integrity: align the outgoing bio in integrity_recheck")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e4137851d4 ]
The tests send 100 pings in 0.1 second intervals and force a timeout of
11 seconds, which is borderline (especially on debug kernels), resulting
in random failures in netdev CI [1].
Fix by increasing the timeout to 20 seconds. It should not prolong the
test unless something is wrong, in which case the test will rightfully
fail.
[1]
# selftests: net/forwarding: vxlan_bridge_1d_port_8472_ipv6.sh
# INFO: Running tests with UDP port 8472
# TEST: ping: local->local [ OK ]
# TEST: ping: local->remote 1 [FAIL]
# Ping failed
[...]
Fixes: b07e9957f2 ("selftests: forwarding: Add VxLAN tests with a VLAN-unaware bridge for IPv6")
Fixes: 728b35259e ("selftests: forwarding: Add VxLAN tests with a VLAN-aware bridge for IPv6")
Reported-by: Paolo Abeni <pabeni@redhat.com>
Closes: https://lore.kernel.org/netdev/24a7051fdcd1f156c3704bca39e4b3c41dfc7c4b.camel@redhat.com/
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20240320065717.4145325-1-idosch@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7eaf837a4e ]
If nft_netdev_register_hooks() fails, the memory associated with
nft_stats is not freed, causing a memory leak.
This patch fixes it by moving nft_stats_alloc() down after
nft_netdev_register_hooks() succeeds.
Fixes: b9703ed44f ("netfilter: nf_tables: support for adding new devices to an existing netdev chain")
Signed-off-by: Quan Tian <tianquan23@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69ddba9d17 ]
Currently, the MT753X switches treat frames with :01-0D and :0F MAC DAs as
regular multicast frames, therefore flooding them to user ports.
On page 205, section "8.6.3 Frame filtering" of the active standard, IEEE
Std 802.1Q™-2022, it is stated that frames with 01:80:C2:00:00:00-0F as MAC
DA must only be propagated to C-VLAN and MAC Bridge components. That means
VLAN-aware and VLAN-unaware bridges. On the switch designs with CPU ports,
these frames are supposed to be processed by the CPU (software). So we make
the switch only forward them to the CPU port. And if received from a CPU
port, forward to a single port. The software is responsible of making the
switch conform to the latter by setting a single port as destination port
on the special tag.
This switch intellectual property cannot conform to this part of the
standard fully. Whilst the REV_UN frame tag covers the remaining :04-0D and
:0F MAC DAs, it also includes :22-FF which the scope of propagation is not
supposed to be restricted for these MAC DAs.
Set frames with :01-03 MAC DAs to be trapped to the CPU port(s). Add a
comment for the remaining MAC DAs.
Note that the ingress port must have a PVID assigned to it for the switch
to forward untagged frames. A PVID is set by default on VLAN-aware and
VLAN-unaware ports. However, when the network interface that pertains to
the ingress port is attached to a vlan_filtering enabled bridge, the user
can remove the PVID assignment from it which would prevent the link-local
frames from being trapped to the CPU port. I am yet to see a way to forward
link-local frames while preventing other untagged frames from being
forwarded too.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8bf353577 ]
Whether VLAN-aware or not, on every VID VLAN table entry that has the CPU
port as a member of it, frames are set to egress the CPU port with the VLAN
tag stacked. This is so that VLAN tags can be appended after hardware
special tag (called DSA tag in the context of Linux drivers).
For user ports on a VLAN-unaware bridge, frame ingressing the user port
egresses CPU port with only the special tag.
For user ports on a VLAN-aware bridge, frame ingressing the user port
egresses CPU port with the special tag and the VLAN tag.
This causes issues with link-local frames, specifically BPDUs, because the
software expects to receive them VLAN-untagged.
There are two options to make link-local frames egress untagged. Setting
CONSISTENT or UNTAGGED on the EG_TAG bits on the relevant register.
CONSISTENT means frames egress exactly as they ingress. That means
egressing with the VLAN tag they had at ingress or egressing untagged if
they ingressed untagged. Although link-local frames are not supposed to be
transmitted VLAN-tagged, if they are done so, when egressing through a CPU
port, the special tag field will be broken.
BPDU egresses CPU port with VLAN tag egressing stacked, received on
software:
00:01:25.104821 AF Unknown (382365846), length 106:
| STAG | | VLAN |
0x0000: 0000 6c27 614d 4143 0001 0000 8100 0001 ..l'aMAC........
0x0010: 0026 4242 0300 0000 0000 0000 6c27 614d .&BB........l'aM
0x0020: 4143 0000 0000 0000 6c27 614d 4143 0000 AC......l'aMAC..
0x0030: 0000 1400 0200 0f00 0000 0000 0000 0000 ................
BPDU egresses CPU port with VLAN tag egressing untagged, received on
software:
00:23:56.628708 AF Unknown (25215488), length 64:
| STAG |
0x0000: 0000 6c27 614d 4143 0001 0000 0026 4242 ..l'aMAC.....&BB
0x0010: 0300 0000 0000 0000 6c27 614d 4143 0000 ........l'aMAC..
0x0020: 0000 0000 6c27 614d 4143 0000 0000 1400 ....l'aMAC......
0x0030: 0200 0f00 0000 0000 0000 0000 ............
BPDU egresses CPU port with VLAN tag egressing tagged, received on
software:
00:01:34.311963 AF Unknown (25215488), length 64:
| Mess |
0x0000: 0000 6c27 614d 4143 0001 0001 0026 4242 ..l'aMAC.....&BB
0x0010: 0300 0000 0000 0000 6c27 614d 4143 0000 ........l'aMAC..
0x0020: 0000 0000 6c27 614d 4143 0000 0000 1400 ....l'aMAC......
0x0030: 0200 0f00 0000 0000 0000 0000 ............
To prevent confusing the software, force the frame to egress UNTAGGED
instead of CONSISTENT. This way, frames can't possibly be received TAGGED
by software which would have the special tag field broken.
VLAN Tag Egress Procedure
For all frames, one of these options set the earliest in this order will
apply to the frame:
- EG_TAG in certain registers for certain frames.
This will apply to frame with matching MAC DA or EtherType.
- EG_TAG in the address table.
This will apply to frame at its incoming port.
- EG_TAG in the PVC register.
This will apply to frame at its incoming port.
- EG_CON and [EG_TAG per port] in the VLAN table.
This will apply to frame at its outgoing port.
- EG_TAG in the PCR register.
This will apply to frame at its outgoing port.
EG_TAG in certain registers for certain frames:
PPPoE Discovery_ARP/RARP: PPP_EG_TAG and ARP_EG_TAG in the APC register.
IGMP_MLD: IGMP_EG_TAG and MLD_EG_TAG in the IMC register.
BPDU and PAE: BPDU_EG_TAG and PAE_EG_TAG in the BPC register.
REV_01 and REV_02: R01_EG_TAG and R02_EG_TAG in the RGAC1 register.
REV_03 and REV_0E: R03_EG_TAG and R0E_EG_TAG in the RGAC2 register.
REV_10 and REV_20: R10_EG_TAG and R20_EG_TAG in the RGAC3 register.
REV_21 and REV_UN: R21_EG_TAG and RUN_EG_TAG in the RGAC4 register.
With this change, it can be observed that a bridge interface with stp_state
and vlan_filtering enabled will properly block ports now.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d6dbbb1124 ]
NAPI threads can keep polling packets under load. Currently it is only
calling cond_resched() before repolling, but it is not sufficient to
clear out the holdout of RCU tasks, which prevent BPF tracing programs
from detaching for long period. This can be reproduced easily with
following set up:
ip netns add test1
ip netns add test2
ip -n test1 link add veth1 type veth peer name veth2 netns test2
ip -n test1 link set veth1 up
ip -n test1 link set lo up
ip -n test2 link set veth2 up
ip -n test2 link set lo up
ip -n test1 addr add 192.168.1.2/31 dev veth1
ip -n test1 addr add 1.1.1.1/32 dev lo
ip -n test2 addr add 192.168.1.3/31 dev veth2
ip -n test2 addr add 2.2.2.2/31 dev lo
ip -n test1 route add default via 192.168.1.3
ip -n test2 route add default via 192.168.1.2
for i in `seq 10 210`; do
for j in `seq 10 210`; do
ip netns exec test2 iptables -I INPUT -s 3.3.$i.$j -p udp --dport 5201
done
done
ip netns exec test2 ethtool -K veth2 gro on
ip netns exec test2 bash -c 'echo 1 > /sys/class/net/veth2/threaded'
ip netns exec test1 ethtool -K veth1 tso off
Then run an iperf3 client/server and a bpftrace script can trigger it:
ip netns exec test2 iperf3 -s -B 2.2.2.2 >/dev/null&
ip netns exec test1 iperf3 -c 2.2.2.2 -B 1.1.1.1 -u -l 1500 -b 3g -t 100 >/dev/null&
bpftrace -e 'kfunc:__napi_poll{@=count();} interval:s:1{exit();}'
Report RCU quiescent states periodically will resolve the issue.
Fixes: 29863d41bb ("net: implement threaded-able napi poll loop support")
Reviewed-by: Jesper Dangaard Brouer <hawk@kernel.org>
Signed-off-by: Yan Zhai <yan@cloudflare.com>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Link: https://lore.kernel.org/r/4c3b0d3f32d3b18949d75b18e5e1d9f13a24f025.1710877680.git.yan@cloudflare.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a77557d48 ]
When under heavy load, network processing can run CPU-bound for many
tens of seconds. Even in preemptible kernels (non-RT kernel), this can
block RCU Tasks grace periods, which can cause trace-event removal to
take more than a minute, which is unacceptably long.
This commit therefore creates a new helper function that passes through
both RCU and RCU-Tasks quiescent states every 100 milliseconds. This
hard-coded value suffices for current workloads.
Suggested-by: Paul E. McKenney <paulmck@kernel.org>
Reviewed-by: Jesper Dangaard Brouer <hawk@kernel.org>
Signed-off-by: Yan Zhai <yan@cloudflare.com>
Reviewed-by: Paul E. McKenney <paulmck@kernel.org>
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Link: https://lore.kernel.org/r/90431d46ee112d2b0af04dbfe936faaca11810a5.1710877680.git.yan@cloudflare.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: d6dbbb1124 ("net: report RCU QS on threaded NAPI repolling")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0e256f3dd ]
Clone already always provides a current view of the lookup table, use it
to destroy the set, otherwise it is possible to destroy elements twice.
This fix requires:
212ed75dc5 ("netfilter: nf_tables: integrate pipapo into commit protocol")
which came after:
9827a0e6e2 ("netfilter: nft_set_pipapo: release elements in clone from abort path").
Fixes: 9827a0e6e2 ("netfilter: nft_set_pipapo: release elements in clone from abort path")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50e60de381 ]
For PF to AF interrupt vector and VF to AF vector same
interrupt handler is registered which is causing race condition.
When two interrupts are raised to two CPUs at same time
then two cores serve same event corrupting the data.
Fixes: 7304ac4567 ("octeontx2-af: Add mailbox IRQ and msg handlers")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dfcf6355f5 ]
When PF sending link status messages to VF, it is possible
that by the time link_event_task work function is executed
VF might have brought down. Hence before sending VF link
status message check whether VF is up to receive it.
Fixes: ad513ed938 ("octeontx2-vf: Link event notification support")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7558ce0d97 ]
Only one execution context for the workqueue used for PF and
VFs mailbox communication is incorrect since multiple works are
queued simultaneously by all the VFs and PF link UP messages.
Hence use default number of execution contexts by passing zero
as max_active to alloc_workqueue function. With this fix in place,
modify UP messages also to wait until completion.
Fixes: d424b6c024 ("octeontx2-pf: Enable SRIOV and added VF mbox handling")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cbf2f24939 ]
During VF driver remove, a message is sent to detach VF
resources to PF but VF is not waiting until message is
complete. Also mailbox interrupts need to be turned off
after the detach resource message is complete. This patch
fixes that problem.
Fixes: 05fcc9e089 ("octeontx2-pf: Attach NIX and NPA block LFs")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a88e0f936b ]
A single line of interrupt is used to receive up notifications
and down reply messages from AF to PF (similarly from PF to its VF).
PF acts as bridge and forwards VF messages to AF and sends respsones
back from AF to VF. When an async event like link event is received
by up message when PF is in middle of forwarding VF message then
mailbox errors occur because PF state machine is corrupted.
Since VF is a separate driver or VF driver can be in a VM it is
not possible to serialize from the start of communication at VF.
Hence to differentiate between type of messages at PF this patch makes
sender to set mbox data register with distinct values for up and down
messages. Sender also checks whether previous interrupt is received
before triggering current interrupt by waiting for mailbox data register
to become zero.
Fixes: 5a6d7c9dae ("octeontx2-pf: Mailbox communication with AF")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d27e2da94a ]
Fix race condition leading to system crash during EEH error handling
During EEH error recovery, the bnx2x driver's transmit timeout logic
could cause a race condition when handling reset tasks. The
bnx2x_tx_timeout() schedules reset tasks via bnx2x_sp_rtnl_task(),
which ultimately leads to bnx2x_nic_unload(). In bnx2x_nic_unload()
SGEs are freed using bnx2x_free_rx_sge_range(). However, this could
overlap with the EEH driver's attempt to reset the device using
bnx2x_io_slot_reset(), which also tries to free SGEs. This race
condition can result in system crashes due to accessing freed memory
locations in bnx2x_free_rx_sge()
799 static inline void bnx2x_free_rx_sge(struct bnx2x *bp,
800 struct bnx2x_fastpath *fp, u16 index)
801 {
802 struct sw_rx_page *sw_buf = &fp->rx_page_ring[index];
803 struct page *page = sw_buf->page;
....
where sw_buf was set to NULL after the call to dma_unmap_page()
by the preceding thread.
EEH: Beginning: 'slot_reset'
PCI 0011:01:00.0#10000: EEH: Invoking bnx2x->slot_reset()
bnx2x: [bnx2x_io_slot_reset:14228(eth1)]IO slot reset initializing...
bnx2x 0011:01:00.0: enabling device (0140 -> 0142)
bnx2x: [bnx2x_io_slot_reset:14244(eth1)]IO slot reset --> driver unload
Kernel attempted to read user page (0) - exploit attempt? (uid: 0)
BUG: Kernel NULL pointer dereference on read at 0x00000000
Faulting instruction address: 0xc0080000025065fc
Oops: Kernel access of bad area, sig: 11 [#1]
.....
Call Trace:
[c000000003c67a20] [c00800000250658c] bnx2x_io_slot_reset+0x204/0x610 [bnx2x] (unreliable)
[c000000003c67af0] [c0000000000518a8] eeh_report_reset+0xb8/0xf0
[c000000003c67b60] [c000000000052130] eeh_pe_report+0x180/0x550
[c000000003c67c70] [c00000000005318c] eeh_handle_normal_event+0x84c/0xa60
[c000000003c67d50] [c000000000053a84] eeh_event_handler+0xf4/0x170
[c000000003c67da0] [c000000000194c58] kthread+0x1c8/0x1d0
[c000000003c67e10] [c00000000000cf64] ret_from_kernel_thread+0x5c/0x64
To solve this issue, we need to verify page pool allocations before
freeing.
Fixes: 4cace675d6 ("bnx2x: Alloc 4k fragment for each rx ring buffer element")
Signed-off-by: Thinh Tran <thinhtr@linux.ibm.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20240315205535.1321-1-thinhtr@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55e565c42d ]
Memory for the "checksums" pointer will leak if the data is rechecked
after checksum failure (because the associated kfree won't happen due
to 'goto skip_io').
Fix this by freeing the checksums memory before recheck, and just use
the "checksum_onstack" memory for storing checksum during recheck.
Fixes: c88f5e553f ("dm-integrity: recheck the integrity tag after a failure")
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 32fa4366cc ]
read_poll_timeout inside phy_read_poll_timeout can set val negative
in some cases (for example, __mdiobus_read inside phy_read can return
-EOPNOTSUPP).
Supposedly, commit 4ec7329517 ("net: phylib: fix phy_read*_poll_timeout()")
should fix problems with wrong-signed vals, but I do not see how
as val is sent to phy_read as is and __val = phy_read (not val)
is checked for sign.
Change val type for signed to allow better error handling as done in other
phy_read_poll_timeout callers. This will not fix any error handling
by itself, but allows, for example, to modify cond with appropriate
sign check or check resulting val separately.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 014068dcb5 ("net: phy: genphy_loopback: add link speed configuration")
Signed-off-by: Nikita Kiryushin <kiryushin@ancud.ru>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240315175052.8049-1-kiryushin@ancud.ru
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1065da21e5 ]
If EOF is encountered, ceph_sync_read() return value is adjusted down
according to i_size, but the "to" iter is advanced by the actual number
of bytes read. Then, when retrying, the remainder of the range may be
skipped incorrectly.
Ensure that the "to" iter is advanced only until EOF.
[ idryomov: changelog ]
Fixes: c3d8e0b5de ("ceph: return the real size read when it hits EOF")
Reported-by: Frank Hsiao <frankhsiao@qnap.com>
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Tested-by: Frank Hsiao <frankhsiao@qnap.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c9b3b81716 ]
Since the referenced commit, the xfrm_inner_extract_output() function
uses the protocol field to determine the address family. So not setting
it for IPv4 raw sockets meant that such packets couldn't be tunneled via
IPsec anymore.
IPv6 raw sockets are not affected as they already set the protocol since
9c9c9ad5fa ("ipv6: set skb->protocol on tcp, raw and ip6_append_data
genereated skbs").
Fixes: f4796398f2 ("xfrm: Remove inner/outer modes from output path")
Signed-off-by: Tobias Brunner <tobias@strongswan.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Link: https://lore.kernel.org/r/c5d9a947-eb19-4164-ac99-468ea814ce20@strongswan.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1422f28826 ]
acquire/release_in_xmit() work as bit lock in rds_send_xmit(), so they
are expected to ensure acquire/release memory ordering semantics.
However, test_and_set_bit/clear_bit() don't imply such semantics, on
top of this, following smp_mb__after_atomic() does not guarantee release
ordering (memory barrier actually should be placed before clear_bit()).
Instead, we use clear_bit_unlock/test_and_set_bit_lock() here.
Fixes: 0f4b1c7e89 ("rds: fix rds_send_xmit() serialization")
Fixes: 1f9ecd7eac ("RDS: Pass rds_conn_path to rds_send_xmit()")
Signed-off-by: Yewon Choi <woni9911@gmail.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Link: https://lore.kernel.org/r/ZfQUxnNTO9AJmzwc@libra05
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5c0ed17fe ]
When use_dma_api and premapped are true, then the do_unmap is false.
Because the do_unmap is false, vring_unmap_extra_packed is not called by
detach_buf_packed.
if (unlikely(vq->do_unmap)) {
curr = id;
for (i = 0; i < state->num; i++) {
vring_unmap_extra_packed(vq,
&vq->packed.desc_extra[curr]);
curr = vq->packed.desc_extra[curr].next;
}
}
So the indirect desc table is not unmapped. This causes the unmap leak.
So here, we check vq->use_dma_api instead. Synchronously, dma info is
updated based on use_dma_api judgment
This bug does not occur, because no driver use the premapped with
indirect.
Fixes: b319940f83 ("virtio_ring: skip unmap for premapped")
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Message-Id: <20240223071833.26095-1-xuanzhuo@linux.alibaba.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 749a401683 ]
The MLX driver was not updating its control virtqueue size at set_vq_num
and instead always initialized to MLX5_CVQ_MAX_ENT (16) at
setup_cvq_vring.
Qemu would try to set the size to 64 by default, however, because the
CVQ size always was initialized to 16, an error would be thrown when
sending >16 control messages (as used-ring entry 17 is initialized to 0).
For example, starting a guest with x-svq=on and then executing the
following command would produce the error below:
# for i in {1..20}; do ifconfig eth0 hw ether XX:xx:XX:xx:XX:XX; done
qemu-system-x86_64: Insufficient written data (0)
[ 435.331223] virtio_net virtio0: Failed to set mac address by vq command.
SIOCSIFHWADDR: Invalid argument
Acked-by: Dragos Tatulea <dtatulea@nvidia.com>
Acked-by: Eugenio Pérez <eperezma@redhat.com>
Signed-off-by: Jonah Palmer <jonah.palmer@oracle.com>
Message-Id: <20240216142502.78095-1-jonah.palmer@oracle.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Lei Yang <leiyang@redhat.com>
Fixes: 5262912ef3 ("vdpa/mlx5: Add support for control VQ and MAC setting")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f490c492e9 ]
On MT7530, the HT_XTAL_FSEL field of the HWTRAP register stores a 2-bit
value that represents the frequency of the crystal oscillator connected to
the switch IC. The field is populated by the state of the ESW_P4_LED_0 and
ESW_P4_LED_0 pins, which is done right after reset is deasserted.
ESW_P4_LED_0 ESW_P3_LED_0 Frequency
-----------------------------------------
0 0 Reserved
0 1 20MHz
1 0 40MHz
1 1 25MHz
On MT7531, the XTAL25 bit of the STRAP register stores this. The LAN0LED0
pin is used to populate the bit. 25MHz when the pin is high, 40MHz when
it's low.
These pins are also used with LEDs, therefore, their state can be set to
something other than the bootstrapping configuration. For example, a link
may be established on port 3 before the DSA subdriver takes control of the
switch which would set ESW_P3_LED_0 to high.
Currently on mt7530_setup() and mt7531_setup(), 1000 - 1100 usec delay is
described between reset assertion and deassertion. Some switch ICs in real
life conditions cannot always have these pins set back to the bootstrapping
configuration before reset deassertion in this amount of delay. This causes
wrong crystal frequency to be selected which puts the switch in a
nonfunctional state after reset deassertion.
The tests below are conducted on an MT7530 with a 40MHz crystal oscillator
by Justin Swartz.
With a cable from an active peer connected to port 3 before reset, an
incorrect crystal frequency (0b11 = 25MHz) is selected:
[1] [3] [5]
: : :
_____________________________ __________________
ESW_P4_LED_0 |_______|
_____________________________
ESW_P3_LED_0 |__________________________
: : : :
: : [4]...:
: :
[2]................:
[1] Reset is asserted.
[2] Period of 1000 - 1100 usec.
[3] Reset is deasserted.
[4] Period of 315 usec. HWTRAP register is populated with incorrect
XTAL frequency.
[5] Signals reflect the bootstrapped configuration.
Increase the delay between reset_control_assert() and
reset_control_deassert(), and gpiod_set_value_cansleep(priv->reset, 0) and
gpiod_set_value_cansleep(priv->reset, 1) to 5000 - 5100 usec. This amount
ensures a higher possibility that the switch IC will have these pins back
to the bootstrapping configuration before reset deassertion.
With a cable from an active peer connected to port 3 before reset, the
correct crystal frequency (0b10 = 40MHz) is selected:
[1] [2-1] [3] [5]
: : : :
_____________________________ __________________
ESW_P4_LED_0 |_______|
___________________ _______
ESW_P3_LED_0 |_________| |__________________
: : : : :
: [2-2]...: [4]...:
[2]................:
[1] Reset is asserted.
[2] Period of 5000 - 5100 usec.
[2-1] ESW_P3_LED_0 goes low.
[2-2] Remaining period of 5000 - 5100 usec.
[3] Reset is deasserted.
[4] Period of 310 usec. HWTRAP register is populated with bootstrapped
XTAL frequency.
[5] Signals reflect the bootstrapped configuration.
ESW_P3_LED_0 low period before reset deassertion:
5000 usec
- 5100 usec
TEST RESET HOLD
# (usec)
---------------------
1 5410
2 5440
3 4375
4 5490
5 5475
6 4335
7 4370
8 5435
9 4205
10 4335
11 3750
12 3170
13 4395
14 4375
15 3515
16 4335
17 4220
18 4175
19 4175
20 4350
Min 3170
Max 5490
Median 4342.500
Avg 4466.500
Revert commit 2920dd92b9 ("net: dsa: mt7530: disable LEDs before reset").
Changing the state of pins via reset assertion is simpler and more
efficient than doing so by setting the LED controller off.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Fixes: c288575f78 ("net: dsa: mt7530: Add the support of MT7531 switch")
Co-developed-by: Justin Swartz <justin.swartz@risingedge.co.za>
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7db7775ea ]
Commit d3256efd8e ("veth: allow enabling NAPI even without XDP") tried to fix
the fact that GRO was not possible without XDP, because veth did not use NAPI
without XDP. However, it also introduced the behaviour that GRO is always
enabled, when XDP is enabled.
While it might be desired for most cases, it is confusing for the user at best
as the GRO flag suddenly changes, when an XDP program is attached. It also
introduces some complexities in state management as was partially addressed in
commit fe9f801355 ("net: veth: clear GRO when clearing XDP even when down").
But the biggest problem is that it is not possible to disable GRO at all, when
an XDP program is attached, which might be needed for some use cases.
Fix this by not touching the GRO flag on XDP enable/disable as the code already
supports switching to NAPI if either GRO or XDP is requested.
Link: https://lore.kernel.org/lkml/20240311124015.38106-1-ignat@cloudflare.com/
Fixes: d3256efd8e ("veth: allow enabling NAPI even without XDP")
Fixes: fe9f801355 ("net: veth: clear GRO when clearing XDP even when down")
Signed-off-by: Ignat Korchagin <ignat@cloudflare.com>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d277f9d828 ]
In bind_evtchn_to_irq_chip() don't increment the refcnt of the event
channel blindly. In case the event channel is NOT refcounted, issue a
warning instead.
Add an additional safety net by doing the refcnt increment only if the
caller has specified IRQF_SHARED in the irqflags parameter.
Fixes: 9e90e58c11 ("xen: evtchn: Allow shared registration of IRQ handers")
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com>
Link: https://lore.kernel.org/r/20240313071409.25913-3-jgross@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea80e3ed09 ]
A patch to resolve an issue was found in MediaTek's GPL-licensed SDK:
In the mtk_ppe_stop() function, the PPE scan mode is not disabled before
disabling the PPE. This can potentially lead to a hang during the process
of disabling the PPE.
Without this patch, the PPE may experience a hang during the reboot test.
Link: b40da332df
Fixes: ba37b7caf1 ("net: ethernet: mtk_eth_soc: add support for initializing the PPE")
Suggested-by: Bc-bocun Chen <bc-bocun.chen@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f1b85ef15a ]
Clearing bit MAC_MCR_FORCE_LINK which forces the link down too early
can result in MAC ending up in a broken/blocked state.
Fix this by handling this bit in the .mac_link_up and .mac_link_down
calls instead of in .mac_finish.
Fixes: b8fc9f3082 ("net: ethernet: mediatek: Add basic PHYLINK support")
Suggested-by: Mason-cw Chang <Mason-cw.Chang@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de105068fe ]
We found a issue on production environment while using NVMe over RDMA,
admin_q reconnect failed forever while remote target and network is ok.
After dig into it, we found it may caused by a ABBA deadlock due to tag
allocation. In my case, the tag was hold by a keep alive request
waiting inside admin_q, as we quiesced admin_q while reset ctrl, so the
request maked as idle and will not process before reset success. As
fabric_q shares tagset with admin_q, while reconnect remote target, we
need a tag for connect command, but the only one reserved tag was held
by keep alive command which waiting inside admin_q. As a result, we
failed to reconnect admin_q forever. In order to fix this issue, I
think we should keep two reserved tags for admin queue.
Fixes: ed01fee283 ("nvme-fabrics: only reserve a single tag")
Signed-off-by: Chunguang Xu <chunguang.xu@shopee.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 67d1189d10 ]
Looking at the error path of __io_uaddr_map, if we fail after pinning
the pages for any reasons, ret will be set to -EINVAL and the error
handler won't properly release the pinned pages.
I didn't manage to trigger it without forcing a failure, but it can
happen in real life when memory is heavily fragmented.
Signed-off-by: Gabriel Krisman Bertazi <krisman@suse.de>
Fixes: 223ef47431 ("io_uring: don't allow IORING_SETUP_NO_MMAP rings on highmem pages")
Link: https://lore.kernel.org/r/20240313213912.1920-1-krisman@suse.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f37a4d6b4a ]
In the existing code, per-policy flags don't have any impact i.e.
if cpufreq_driver boost is enabled and boost is disabled for one or
more of the policies, the cpufreq driver will behave as if boost is
enabled.
Fix this by incorporating per-policy boost flag in the policy->max
computation used in cpufreq_frequency_table_cpuinfo and setting the
default per-policy boost to mirror the cpufreq_driver boost flag.
Fixes: 218a06a79d ("cpufreq: Support per-policy performance boost")
Reported-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Tested-by:Yipeng Zou <zouyipeng@huawei.com> <mailto:zouyipeng@huawei.com>
Reviewed-by: Yipeng Zou <zouyipeng@huawei.com> <mailto:zouyipeng@huawei.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 72ebb41b88 ]
A previous bugfix added a call to kcalloc(), which starting in gcc-14
causes a harmless warning about the argument order:
drivers/soc/fsl/dpio/dpio-service.c: In function 'dpaa2_io_service_enqueue_multiple_desc_fq':
drivers/soc/fsl/dpio/dpio-service.c:526:29: error: 'kcalloc' sizes specified with 'sizeof' in the earlier argument and not in the later argument [-Werror=calloc-transposed-args]
526 | ed = kcalloc(sizeof(struct qbman_eq_desc), 32, GFP_KERNEL);
| ^~~~~~
drivers/soc/fsl/dpio/dpio-service.c:526:29: note: earlier argument should specify number of elements, later size of each element
Since the two are only multiplied, the order does not change the
behavior, so just fix it now to shut up the compiler warning.
Dmity independently came up with the same fix.
Fixes: 5c4a5999b2 ("soc: fsl: dpio: avoid stack usage warning")
Reported-by: Dmitry Antipov <dmantipov@yandex.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 367c50f784 ]
Current average steal timer calculation produces volatile and inflated
values. The only user of this value is KVM so far and it uses that to
decide whether or not to yield the vCPU which is seeing steal time.
KVM compares average steal timer to a threshold and if the threshold
is past then it does not allow CPU polling and yields it to host, else
it keeps the CPU by polling.
Since KVM's steal time threshold is very low by default (%10) it most
likely is not effected much by the bloated average steal timer values
because the operating region is pretty small. However there might be
new users in the future who might rely on this number. Fix average
steal timer calculation by changing the formula from:
avg_steal_timer = avg_steal_timer / 2 + steal_timer;
to the following:
avg_steal_timer = (avg_steal_timer + steal_timer) / 2;
This ensures that avg_steal_timer is actually a naive average of steal
timer values. It now closely follows steal timer values but of course
in a smoother manner.
Fixes: 152e9b8676 ("s390/vtime: steal time exponential moving average")
Signed-off-by: Mete Durlu <meted@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e642921dfe ]
Use wake_up API instead of wake_up_interruptible, since
wait_event_timeout API is used for waiting on command completion.
Fixes: 1463f382f5 ("octeontx2-af: Add support for CGX link management")
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2a750d6a5b ]
syzkaller reported a warning of netns tracker [0] followed by KASAN
splat [1] and another ref tracker warning [1].
syzkaller could not find a repro, but in the log, the only suspicious
sequence was as follows:
18:26:22 executing program 1:
r0 = socket$inet6_mptcp(0xa, 0x1, 0x106)
...
connect$inet6(r0, &(0x7f0000000080)={0xa, 0x4001, 0x0, @loopback}, 0x1c) (async)
The notable thing here is 0x4001 in connect(), which is RDS_TCP_PORT.
So, the scenario would be:
1. unshare(CLONE_NEWNET) creates a per netns tcp listener in
rds_tcp_listen_init().
2. syz-executor connect()s to it and creates a reqsk.
3. syz-executor exit()s immediately.
4. netns is dismantled. [0]
5. reqsk timer is fired, and UAF happens while freeing reqsk. [1]
6. listener is freed after RCU grace period. [2]
Basically, reqsk assumes that the listener guarantees netns safety
until all reqsk timers are expired by holding the listener's refcount.
However, this was not the case for kernel sockets.
Commit 740ea3c4a0 ("tcp: Clean up kernel listener's reqsk in
inet_twsk_purge()") fixed this issue only for per-netns ehash.
Let's apply the same fix for the global ehash.
[0]:
ref_tracker: net notrefcnt@0000000065449cc3 has 1/1 users at
sk_alloc (./include/net/net_namespace.h:337 net/core/sock.c:2146)
inet6_create (net/ipv6/af_inet6.c:192 net/ipv6/af_inet6.c:119)
__sock_create (net/socket.c:1572)
rds_tcp_listen_init (net/rds/tcp_listen.c:279)
rds_tcp_init_net (net/rds/tcp.c:577)
ops_init (net/core/net_namespace.c:137)
setup_net (net/core/net_namespace.c:340)
copy_net_ns (net/core/net_namespace.c:497)
create_new_namespaces (kernel/nsproxy.c:110)
unshare_nsproxy_namespaces (kernel/nsproxy.c:228 (discriminator 4))
ksys_unshare (kernel/fork.c:3429)
__x64_sys_unshare (kernel/fork.c:3496)
do_syscall_64 (arch/x86/entry/common.c:52 arch/x86/entry/common.c:83)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:129)
...
WARNING: CPU: 0 PID: 27 at lib/ref_tracker.c:179 ref_tracker_dir_exit (lib/ref_tracker.c:179)
[1]:
BUG: KASAN: slab-use-after-free in inet_csk_reqsk_queue_drop (./include/net/inet_hashtables.h:180 net/ipv4/inet_connection_sock.c:952 net/ipv4/inet_connection_sock.c:966)
Read of size 8 at addr ffff88801b370400 by task swapper/0/0
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014
Call Trace:
<IRQ>
dump_stack_lvl (lib/dump_stack.c:107 (discriminator 1))
print_report (mm/kasan/report.c:378 mm/kasan/report.c:488)
kasan_report (mm/kasan/report.c:603)
inet_csk_reqsk_queue_drop (./include/net/inet_hashtables.h:180 net/ipv4/inet_connection_sock.c:952 net/ipv4/inet_connection_sock.c:966)
reqsk_timer_handler (net/ipv4/inet_connection_sock.c:979 net/ipv4/inet_connection_sock.c:1092)
call_timer_fn (./arch/x86/include/asm/jump_label.h:27 ./include/linux/jump_label.h:207 ./include/trace/events/timer.h:127 kernel/time/timer.c:1701)
__run_timers.part.0 (kernel/time/timer.c:1752 kernel/time/timer.c:2038)
run_timer_softirq (kernel/time/timer.c:2053)
__do_softirq (./arch/x86/include/asm/jump_label.h:27 ./include/linux/jump_label.h:207 ./include/trace/events/irq.h:142 kernel/softirq.c:554)
irq_exit_rcu (kernel/softirq.c:427 kernel/softirq.c:632 kernel/softirq.c:644)
sysvec_apic_timer_interrupt (arch/x86/kernel/apic/apic.c:1076 (discriminator 14))
</IRQ>
Allocated by task 258 on cpu 0 at 83.612050s:
kasan_save_stack (mm/kasan/common.c:48)
kasan_save_track (mm/kasan/common.c:68)
__kasan_slab_alloc (mm/kasan/common.c:343)
kmem_cache_alloc (mm/slub.c:3813 mm/slub.c:3860 mm/slub.c:3867)
copy_net_ns (./include/linux/slab.h:701 net/core/net_namespace.c:421 net/core/net_namespace.c:480)
create_new_namespaces (kernel/nsproxy.c:110)
unshare_nsproxy_namespaces (kernel/nsproxy.c:228 (discriminator 4))
ksys_unshare (kernel/fork.c:3429)
__x64_sys_unshare (kernel/fork.c:3496)
do_syscall_64 (arch/x86/entry/common.c:52 arch/x86/entry/common.c:83)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:129)
Freed by task 27 on cpu 0 at 329.158864s:
kasan_save_stack (mm/kasan/common.c:48)
kasan_save_track (mm/kasan/common.c:68)
kasan_save_free_info (mm/kasan/generic.c:643)
__kasan_slab_free (mm/kasan/common.c:265)
kmem_cache_free (mm/slub.c:4299 mm/slub.c:4363)
cleanup_net (net/core/net_namespace.c:456 net/core/net_namespace.c:446 net/core/net_namespace.c:639)
process_one_work (kernel/workqueue.c:2638)
worker_thread (kernel/workqueue.c:2700 kernel/workqueue.c:2787)
kthread (kernel/kthread.c:388)
ret_from_fork (arch/x86/kernel/process.c:153)
ret_from_fork_asm (arch/x86/entry/entry_64.S:250)
The buggy address belongs to the object at ffff88801b370000
which belongs to the cache net_namespace of size 4352
The buggy address is located 1024 bytes inside of
freed 4352-byte region [ffff88801b370000, ffff88801b371100)
[2]:
WARNING: CPU: 0 PID: 95 at lib/ref_tracker.c:228 ref_tracker_free (lib/ref_tracker.c:228 (discriminator 1))
Modules linked in:
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014
RIP: 0010:ref_tracker_free (lib/ref_tracker.c:228 (discriminator 1))
...
Call Trace:
<IRQ>
__sk_destruct (./include/net/net_namespace.h:353 net/core/sock.c:2204)
rcu_core (./arch/x86/include/asm/preempt.h:26 kernel/rcu/tree.c:2165 kernel/rcu/tree.c:2433)
__do_softirq (./arch/x86/include/asm/jump_label.h:27 ./include/linux/jump_label.h:207 ./include/trace/events/irq.h:142 kernel/softirq.c:554)
irq_exit_rcu (kernel/softirq.c:427 kernel/softirq.c:632 kernel/softirq.c:644)
sysvec_apic_timer_interrupt (arch/x86/kernel/apic/apic.c:1076 (discriminator 14))
</IRQ>
Reported-by: syzkaller <syzkaller@googlegroups.com>
Suggested-by: Eric Dumazet <edumazet@google.com>
Fixes: 467fa15356 ("RDS-TCP: Support multiple RDS-TCP listen endpoints, one per netns.")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240308200122.64357-3-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c4e97dd2d ]
inet_twsk_purge() uses rcu to find TIME_WAIT and NEW_SYN_RECV
objects to purge.
These objects use SLAB_TYPESAFE_BY_RCU semantic and need special
care. We need to use refcount_inc_not_zero(&sk->sk_refcnt).
Reuse the existing correct logic I wrote for TIME_WAIT,
because both structures have common locations for
sk_state, sk_family, and netns pointer.
If after the refcount_inc_not_zero() the object fields longer match
the keys, use sock_gen_put(sk) to release the refcount.
Then we can call inet_twsk_deschedule_put() for TIME_WAIT,
inet_csk_reqsk_queue_drop_and_put() for NEW_SYN_RECV sockets,
with BH disabled.
Then we need to restart the loop because we had drop rcu_read_lock().
Fixes: 740ea3c4a0 ("tcp: Clean up kernel listener's reqsk in inet_twsk_purge()")
Link: https://lore.kernel.org/netdev/CANn89iLvFuuihCtt9PME2uS1WJATnf5fKjDToa1WzVnRzHnPfg@mail.gmail.com/T/#u
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240308200122.64357-2-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e2ab4b18e ]
The sample rates set by the rockchip_i2s_tdm driver in master mode are
inaccurate up to 5% in several cases, due to the driver logic to configure
clocks and a nasty interaction with the Common Clock Framework.
To understand what happens, here is the relevant section of the clock tree
(slightly simplified), along with the names used in the driver:
vpll0 _OR_ vpll1 "mclk_root"
clk_i2s2_8ch_tx_src "mclk_parent"
clk_i2s2_8ch_tx_mux
clk_i2s2_8ch_tx "mclk" or "mclk_tx"
This is what happens when playing back e.g. at 192 kHz using
audio-graph-card (when recording the same applies, only s/tx/rx/):
0. at probe, rockchip_i2s_tdm_set_sysclk() stores the passed frequency in
i2s_tdm->mclk_tx_freq (*) which is 50176000, and that is never modified
afterwards
1. when playback is started, rockchip_i2s_tdm_hw_params() is called and
does the following two calls
2. rockchip_i2s_tdm_calibrate_mclk():
2a. selects mclk_root0 (vpll0) as a parent for mclk_parent
(mclk_tx_src), which is OK because the vpll0 rate is a good for
192000 (and sumbultiple) rates
2b. sets the mclk_root frequency based on ppm calibration computations
2c. sets mclk_tx_src to 49152000 (= 256 * 192000), which is also OK as
it is a multiple of the required bit clock
3. rockchip_i2s_tdm_set_mclk()
3a. calls clk_set_rate() to set the rate of mclk_tx (clk_i2s2_8ch_tx)
to the value of i2s_tdm->mclk_tx_freq (*), i.e. 50176000 which is
not a multiple of the sampling frequency -- this is not OK
3a1. clk_set_rate() reacts by reparenting clk_i2s2_8ch_tx_src to
vpll1 -- this is not OK because the default vpll1 rate can be
divided to get 44.1 kHz and related rates, not 192 kHz
The result is that the driver does a lot of ad-hoc decisions about clocks
and ends up in using the wrong parent at an unoptimal rate.
Step 0 is one part of the problem: unless the card driver calls set_sysclk
at each stream start, whatever rate is set in mclk_tx_freq during boot will
be taken and used until reboot. Moreover the driver does not care if its
value is not a multiple of any audio frequency.
Another part of the problem is that the whole reparenting and clock rate
setting logic is conflicting with the CCF algorithms to achieve largely the
same goal: selecting the best parent and setting the closest clock
rate. And it turns out that only calling once clk_set_rate() on
clk_i2s2_8ch_tx picks the correct vpll and sets the correct rate.
The fix is based on removing the custom logic in the driver to select the
parent and set the various clocks, and just let the Clock Framework do it
all. As a side effect, the set_sysclk() op becomes useless because we now
let the CCF compute the appropriate value for the sampling rate. It also
implies that the whole calibration logic is now dead code and so it is
removed along with the "PCM Clock Compensation in PPM" kcontrol, which has
always been broken anyway. The handling of the 4 optional clocks also
becomes dead code and is removed.
The actual rates have been tested playing 30 seconds of audio at various
sampling rates before and after this change using sox:
time play -r <sample_rate> -n synth 30 sine 950 gain -3
The time reported in the table below is the 'real' value reported by the
'time' command in the above command line.
rate before after
--------- ------ ------
8000 Hz 30.60s 30.63s
11025 Hz 30.45s 30.51s
16000 Hz 30.47s 30.50s
22050 Hz 30.78s 30.41s
32000 Hz 31.02s 30.43s
44100 Hz 30.78s 30.41s
48000 Hz 29.81s 30.45s
88200 Hz 30.78s 30.41s
96000 Hz 29.79s 30.42s
176400 Hz 27.40s 30.41s
192000 Hz 29.79s 30.42s
While the tests are running the clock tree confirms that:
* without the patch, vpll1 is always used and clk_i2s2_8ch_tx always
produces 50176000 Hz, which cannot be divided for most audio rates
except the slowest ones, generating inaccurate rates
* with the patch:
- for 192000 Hz vpll0 is used
- for 176400 Hz vpll1 is used
- clk_i2s2_8ch_tx always produces (256 * <rate>) Hz
Tested on the RK3308 using the internal audio codec.
Fixes: 081068fd64 ("ASoC: rockchip: add support for i2s-tdm controller")
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://msgid.link/r/20240305-rk3308-audio-codec-v4-1-312acdbe628f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ae0ab0143 ]
fsl_lpspi_probe() is allocating/disposing memory manually with
spi_alloc_host()/spi_alloc_target(), but uses
devm_spi_register_controller(). In case of error after the latter call the
memory will be explicitly freed in the probe function by
spi_controller_put() call, but used afterwards by "devm" management outside
probe() (spi_unregister_controller() <- devm_spi_unregister() below).
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000070
...
Call trace:
kernfs_find_ns
kernfs_find_and_get_ns
sysfs_remove_group
sysfs_remove_groups
device_remove_attrs
device_del
spi_unregister_controller
devm_spi_unregister
release_nodes
devres_release_all
really_probe
driver_probe_device
__device_attach_driver
bus_for_each_drv
__device_attach
device_initial_probe
bus_probe_device
deferred_probe_work_func
process_one_work
worker_thread
kthread
ret_from_fork
Fixes: 5314987de5 ("spi: imx: add lpspi bus driver")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Link: https://msgid.link/r/20240312112050.2503643-1-alexander.sverdlin@siemens.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f0974eccb ]
This kind of state is per-syscall, and since we're doing the waiting off
entering the io_uring_enter(2) syscall, there's no way that iowait can
already be set for this case. Simplify it by setting it if we need to,
and always clearing it to 0 when done.
Fixes: 7b72d661f1 ("io_uring: gate iowait schedule on having pending requests")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f31e0d0c2c ]
Using __exit for the remove function results in the remove callback
being discarded with SND_SOC_TLV320ADC3XXX=y. When such a device gets
unbound (e.g. using sysfs or hotplug), the driver is just removed
without the cleanup being performed. This results in resource leaks. Fix
it by compiling in the remove callback unconditionally.
This also fixes a W=1 modpost warning:
WARNING: modpost: sound/soc/codecs/snd-soc-tlv320adc3xxx: section mismatch in reference: adc3xxx_i2c_driver+0x10 (section: .data) -> adc3xxx_i2c_remove (section: .exit.text)
(which only happens with SND_SOC_TLV320ADC3XXX=m).
Fixes: e9a3b57efd ("ASoC: codec: tlv320adc3xxx: New codec driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://msgid.link/r/20240310143852.397212-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 600556809f ]
Currently the variable irqflags is being set but is not being used,
it appears it should be used in the call to net2272_probe_fin
rather than IRQF_TRIGGER_LOW being used. Kudos to Uwe Kleine-König
for suggesting the fix.
Cleans up clang scan build warning:
drivers/usb/gadget/udc/net2272.c:2610:15: warning: variable 'irqflags'
set but not used [-Wunused-but-set-variable]
Fixes: ceb80363b2 ("USB: net2272: driver for PLX NET2272 USB device controller")
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240307181734.2034407-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 06226d120a ]
When perf_init_event() calls perf_try_init_event() to init pmu driver,
searches for the next pmu driver only when the return value is -ENOENT.
Therefore, hisi_ptt_pmu_event_init() needs to check the type at the
beginning of the function.
Otherwise, in the case of perf-task mode, perf_try_init_event() returns
-EOPNOTSUPP and skips subsequent pmu drivers, causes perf_init_event() to
fail.
Fixes: ff0de066b4 ("hwtracing: hisi_ptt: Add trace function support for HiSilicon PCIe Tune and Trace device")
Signed-off-by: Yang Jihong <yangjihong1@huawei.com>
Reviewed-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20240108121906.3514820-1-yangjihong1@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit af8bbce920 ]
A macro placed at the end of a file with no newline causes an infinite
loop.
[Test Kconfig]
$(info,hello)
\ No newline at end of file
I realized that flex-provided input() returns 0 instead of EOF when it
reaches the end of a file.
Fixes: 104daea149 ("kconfig: reference environment variables directly and remove 'option env='")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f68bbe4dcf ]
The linked commit reverts the change that accidentally used some sysfs
enable/disable functions from Perf which broke the refcounting, but it
also removes the fact that the sysfs disable function disabled the
helpers.
Add a new wrapper function that does both which is used by both Perf and
sysfs, and label the sysfs disable function appropriately. The naming of
all of the functions will be tidied up later to avoid this happening
again.
Fixes: 287e82cf69 ("coresight: Fix crash when Perf and sysfs modes are used concurrently")
Signed-off-by: James Clark <james.clark@arm.com>
Link: https://lore.kernel.org/r/20240129154050.569566-2-james.clark@arm.com
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c77b35ce66 ]
The sparse tool complains about the remove of the _iomem attribute.
stm32_rproc.c:660:17: warning: cast removes address space '__iomem' of expression
Add '__force' to explicitly specify that the cast is intentional.
This conversion is necessary to cast to addresses pointer,
which are then managed by the remoteproc core as a pointer to a
resource_table structure.
Fixes: 8a471396d2 ("remoteproc: stm32: Move resource table setup to rproc_ops")
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Link: https://lore.kernel.org/r/20240117135312.3381936-3-arnaud.pouliquen@foss.st.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a0776c214d upstream.
On Arrow Lake S systems, MEI is no longer strictly connected to bus 0,
while graphics remain exclusively on bus 0. Adapt the component
matching logic to accommodate this change:
Original behavior: Required both MEI and graphics to be on the same
bus 0.
New behavior: Only enforces graphics to be on bus 0 (integrated),
allowing MEI to reside on any bus.
This ensures compatibility with Arrow Lake S and maintains functionality
for the legacy systems.
Fixes: 1dd924f688 ("mei: gsc_proxy: add gsc proxy driver")
Cc: stable@vger.kernel.org # v6.3+
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20240220200020.231192-1-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f53641a6e8 upstream.
The comedi_test devices have a couple of timers (ai_timer and ao_timer)
that can be started to simulate hardware interrupts. Their expiry
functions normally reschedule the timer. The driver code calls either
del_timer_sync() or del_timer() to delete the timers from the queue, but
does not currently prevent the timers from rescheduling themselves so
synchronized deletion may be ineffective.
Add a couple of boolean members (one for each timer: ai_timer_enable and
ao_timer_enable) to the device private data structure to indicate
whether the timers are allowed to reschedule themselves. Set the member
to true when adding the timer to the queue, and to false when deleting
the timer from the queue in the waveform_ai_cancel() and
waveform_ao_cancel() functions.
The del_timer_sync() function is also called from the waveform_detach()
function, but the timer enable members will already be set to false when
that function is called, so no change is needed there.
Fixes: 403fe7f34e ("staging: comedi: comedi_test: fix timer race conditions")
Cc: stable@vger.kernel.org # 4.4+
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20240214100747.16203-1-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 719fcafe07 ]
We've been seeing the following panic in production
BUG: kernel NULL pointer dereference, address: 0000000000000065
PGD 2f485f067 P4D 2f485f067 PUD 2cc5d8067 PMD 0
RIP: 0010:ff_layout_cancel_io+0x3a/0x90 [nfs_layout_flexfiles]
Call Trace:
<TASK>
? __die+0x78/0xc0
? page_fault_oops+0x286/0x380
? __rpc_execute+0x2c3/0x470 [sunrpc]
? rpc_new_task+0x42/0x1c0 [sunrpc]
? exc_page_fault+0x5d/0x110
? asm_exc_page_fault+0x22/0x30
? ff_layout_free_layoutreturn+0x110/0x110 [nfs_layout_flexfiles]
? ff_layout_cancel_io+0x3a/0x90 [nfs_layout_flexfiles]
? ff_layout_cancel_io+0x6f/0x90 [nfs_layout_flexfiles]
pnfs_mark_matching_lsegs_return+0x1b0/0x360 [nfsv4]
pnfs_error_mark_layout_for_return+0x9e/0x110 [nfsv4]
? ff_layout_send_layouterror+0x50/0x160 [nfs_layout_flexfiles]
nfs4_ff_layout_prepare_ds+0x11f/0x290 [nfs_layout_flexfiles]
ff_layout_pg_init_write+0xf0/0x1f0 [nfs_layout_flexfiles]
__nfs_pageio_add_request+0x154/0x6c0 [nfs]
nfs_pageio_add_request+0x26b/0x380 [nfs]
nfs_do_writepage+0x111/0x1e0 [nfs]
nfs_writepages_callback+0xf/0x30 [nfs]
write_cache_pages+0x17f/0x380
? nfs_pageio_init_write+0x50/0x50 [nfs]
? nfs_writepages+0x6d/0x210 [nfs]
? nfs_writepages+0x6d/0x210 [nfs]
nfs_writepages+0x125/0x210 [nfs]
do_writepages+0x67/0x220
? generic_perform_write+0x14b/0x210
filemap_fdatawrite_wbc+0x5b/0x80
file_write_and_wait_range+0x6d/0xc0
nfs_file_fsync+0x81/0x170 [nfs]
? nfs_file_mmap+0x60/0x60 [nfs]
__x64_sys_fsync+0x53/0x90
do_syscall_64+0x3d/0x90
entry_SYSCALL_64_after_hwframe+0x46/0xb0
Inspecting the core with drgn I was able to pull this
>>> prog.crashed_thread().stack_trace()[0]
#0 at 0xffffffffa079657a (ff_layout_cancel_io+0x3a/0x84) in ff_layout_cancel_io at fs/nfs/flexfilelayout/flexfilelayout.c:2021:27
>>> prog.crashed_thread().stack_trace()[0]['idx']
(u32)1
>>> prog.crashed_thread().stack_trace()[0]['flseg'].mirror_array[1].mirror_ds
(struct nfs4_ff_layout_ds *)0xffffffffffffffed
This is clear from the stack trace, we call nfs4_ff_layout_prepare_ds()
which could error out initializing the mirror_ds, and then we go to
clean it all up and our check is only for if (!mirror->mirror_ds). This
is inconsistent with the rest of the users of mirror_ds, which have
if (IS_ERR_OR_NULL(mirror_ds))
to keep from tripping over this exact scenario. Fix this up in
ff_layout_cancel_io() to make sure we don't panic when we get an error.
I also spot checked all the other instances of checking mirror_ds and we
appear to be doing the correct checks everywhere, only unconditionally
dereferencing mirror_ds when we know it would be valid.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Fixes: b739a5bd9d ("NFSv4/flexfiles: Cancel I/O if the layout is recalled or revoked")
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f0c4a46be ]
Below race case can cause data corruption:
Thread A GC thread
- gc_data_segment
- ra_data_block
- locked meta_inode page
- f2fs_inplace_write_data
- invalidate_mapping_pages
: fail to invalidate meta_inode page
due to lock failure or dirty|writeback
status
- f2fs_submit_page_bio
: write last dirty data to old blkaddr
- move_data_block
- load old data from meta_inode page
- f2fs_submit_page_write
: write old data to new blkaddr
Because invalidate_mapping_pages() will skip invalidating page which
has unclear status including locked, dirty, writeback and so on, so
we need to use truncate_inode_pages_range() instead of
invalidate_mapping_pages() to make sure meta_inode page will be dropped.
Fixes: 6aa58d8ad2 ("f2fs: readahead encrypted block during GC")
Fixes: e3b49ea368 ("f2fs: invalidate META_MAPPING before IPU/DIO write")
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f6d721e14 ]
When a file only needs one direct_node, performing the following
operations will cause the file to be unrepairable:
unisoc # ./f2fs_io compress test.apk
unisoc #df -h | grep dm-48
/dev/block/dm-48 112G 112G 1.2M 100% /data
unisoc # ./f2fs_io release_cblocks test.apk
924
unisoc # df -h | grep dm-48
/dev/block/dm-48 112G 112G 4.8M 100% /data
unisoc # dd if=/dev/random of=file4 bs=1M count=3
3145728 bytes (3.0 M) copied, 0.025 s, 120 M/s
unisoc # df -h | grep dm-48
/dev/block/dm-48 112G 112G 1.8M 100% /data
unisoc # ./f2fs_io reserve_cblocks test.apk
F2FS_IOC_RESERVE_COMPRESS_BLOCKS failed: No space left on device
adb reboot
unisoc # df -h | grep dm-48
/dev/block/dm-48 112G 112G 11M 100% /data
unisoc # ./f2fs_io reserve_cblocks test.apk
0
This is because the file has only one direct_node. After returning
to -ENOSPC, reserved_blocks += ret will not be executed. As a result,
the reserved_blocks at this time is still 0, which is not the real
number of reserved blocks. Therefore, fsck cannot be set to repair
the file.
After this patch, the fsck flag will be set to fix this problem.
unisoc # df -h | grep dm-48
/dev/block/dm-48 112G 112G 1.8M 100% /data
unisoc # ./f2fs_io reserve_cblocks test.apk
F2FS_IOC_RESERVE_COMPRESS_BLOCKS failed: No space left on device
adb reboot then fsck will be executed
unisoc # df -h | grep dm-48
/dev/block/dm-48 112G 112G 11M 100% /data
unisoc # ./f2fs_io reserve_cblocks test.apk
924
Fixes: c75488fb4d ("f2fs: introduce F2FS_IOC_RESERVE_COMPRESS_BLOCKS")
Signed-off-by: Xiuhong Wang <xiuhong.wang@unisoc.com>
Signed-off-by: Zhiguo Niu <zhiguo.niu@unisoc.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b7d797d241 ]
The following f2fs_io test will get a "0" result instead of -EINVAL,
unisoc # ./f2fs_io compress file
unisoc # ./f2fs_io reserve_cblocks file
0
it's not reasonable, so the judgement of
atomic_read(&F2FS_I(inode)->i_compr_blocks) should be placed after
the judgement of is_inode_flag_set(inode, FI_COMPRESS_RELEASED).
Fixes: c75488fb4d ("f2fs: introduce F2FS_IOC_RESERVE_COMPRESS_BLOCKS")
Signed-off-by: Xiuhong Wang <xiuhong.wang@unisoc.com>
Signed-off-by: Zhiguo Niu <zhiguo.niu@unisoc.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a35518cae4 ]
Currently, even though xprtsec=tls is specified and used for operations
to MDS, any operations that go to DS travel over unencrypted connection.
Or additionally, if more than 1 DS can serve the data, then trunked
connections are also done unencrypted.
IN GETDEVINCEINFO, we get an entry for the DS which carries a protocol
type (which is TCP), then nfs4_set_ds_client() gets called with TCP
instead of TCP with TLS.
Currently, each trunked connection is created and uses clp->cl_hostname
value which if TLS is used would get passed up in the handshake upcall,
but instead we need to pass in the appropriate trunked address value.
Fixes: c8407f2e56 ("NFS: Add an "xprtsec=" NFS mount option")
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 698ad1a538 ]
The intent is to check if 'dest' is truncated or not. So, >= should be
used instead of >, because strlcat() returns the length of 'dest' and 'src'
excluding the trailing NULL.
Fixes: 56463e50d1 ("NFS: Use super.c for NFSROOT mount option parsing")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd5860ab63 ]
The loop inside nfs_netfs_issue_read() currently does not disable
interrupts while iterating through pages in the xarray to submit
for NFS read. This is not safe though since after taking xa_lock,
another page in the mapping could be processed for writeback inside
an interrupt, and deadlock can occur. The fix is simple and clean
if we use xa_for_each_range(), which handles the iteration with RCU
while reducing code complexity.
The problem is easily reproduced with the following test:
mount -o vers=3,fsc 127.0.0.1:/export /mnt/nfs
dd if=/dev/zero of=/mnt/nfs/file1.bin bs=4096 count=1
echo 3 > /proc/sys/vm/drop_caches
dd if=/mnt/nfs/file1.bin of=/dev/null
umount /mnt/nfs
On the console with a lockdep-enabled kernel a message similar to
the following will be seen:
================================
WARNING: inconsistent lock state
6.7.0-lockdbg+ #10 Not tainted
--------------------------------
inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage.
test5/1708 [HC0[0]:SC0[0]:HE1:SE1] takes:
ffff888127baa598 (&xa->xa_lock#4){+.?.}-{3:3}, at:
nfs_netfs_issue_read+0x1b2/0x4b0 [nfs]
{IN-SOFTIRQ-W} state was registered at:
lock_acquire+0x144/0x380
_raw_spin_lock_irqsave+0x4e/0xa0
__folio_end_writeback+0x17e/0x5c0
folio_end_writeback+0x93/0x1b0
iomap_finish_ioend+0xeb/0x6a0
blk_update_request+0x204/0x7f0
blk_mq_end_request+0x30/0x1c0
blk_complete_reqs+0x7e/0xa0
__do_softirq+0x113/0x544
__irq_exit_rcu+0xfe/0x120
irq_exit_rcu+0xe/0x20
sysvec_call_function_single+0x6f/0x90
asm_sysvec_call_function_single+0x1a/0x20
pv_native_safe_halt+0xf/0x20
default_idle+0x9/0x20
default_idle_call+0x67/0xa0
do_idle+0x2b5/0x300
cpu_startup_entry+0x34/0x40
start_secondary+0x19d/0x1c0
secondary_startup_64_no_verify+0x18f/0x19b
irq event stamp: 176891
hardirqs last enabled at (176891): [<ffffffffa67a0be4>]
_raw_spin_unlock_irqrestore+0x44/0x60
hardirqs last disabled at (176890): [<ffffffffa67a0899>]
_raw_spin_lock_irqsave+0x79/0xa0
softirqs last enabled at (176646): [<ffffffffa515d91e>]
__irq_exit_rcu+0xfe/0x120
softirqs last disabled at (176633): [<ffffffffa515d91e>]
__irq_exit_rcu+0xfe/0x120
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&xa->xa_lock#4);
<Interrupt>
lock(&xa->xa_lock#4);
*** DEADLOCK ***
2 locks held by test5/1708:
#0: ffff888127baa498 (&sb->s_type->i_mutex_key#22){++++}-{4:4}, at:
nfs_start_io_read+0x28/0x90 [nfs]
#1: ffff888127baa650 (mapping.invalidate_lock#3){.+.+}-{4:4}, at:
page_cache_ra_unbounded+0xa4/0x280
stack backtrace:
CPU: 6 PID: 1708 Comm: test5 Kdump: loaded Not tainted 6.7.0-lockdbg+
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-1.fc39
04/01/2014
Call Trace:
dump_stack_lvl+0x5b/0x90
mark_lock+0xb3f/0xd20
__lock_acquire+0x77b/0x3360
_raw_spin_lock+0x34/0x80
nfs_netfs_issue_read+0x1b2/0x4b0 [nfs]
netfs_begin_read+0x77f/0x980 [netfs]
nfs_netfs_readahead+0x45/0x60 [nfs]
nfs_readahead+0x323/0x5a0 [nfs]
read_pages+0xf3/0x5c0
page_cache_ra_unbounded+0x1c8/0x280
filemap_get_pages+0x38c/0xae0
filemap_read+0x206/0x5e0
nfs_file_read+0xb7/0x140 [nfs]
vfs_read+0x2a9/0x460
ksys_read+0xb7/0x140
Fixes: 000dbe0bec ("NFS: Convert buffered read paths to use netfs when fscache is enabled")
Suggested-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Dave Wysochanski <dwysocha@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: David Howells <dhowells@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7324858237 ]
@type in f2fs_allocate_data_block() indicates log header's type, it
can be CURSEG_COLD_DATA_PINNED or CURSEG_ALL_DATA_ATGC, rather than
type of data/node, however IS_DATASEG()/IS_NODESEG() only accept later
one, fix it.
Fixes: 093749e296 ("f2fs: support age threshold based garbage collection")
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dbd7c0088b ]
The driver never sets a default timeout value, therefore it is
initialized to zero. When CONFIG_WATCHDOG_HANDLE_BOOT_ENABLED is
enabled, the watchdog is started during probe. The kernel is supposed to
automatically ping the watchdog from this point until userspace takes
over, but this does not happen if the configured timeout is zero. A zero
timeout causes watchdog_need_worker() to return false, so the heartbeat
worker does not run and the system therefore resets soon after the
driver is probed.
This patch fixes this by setting an arbitrary non-zero default timeout.
The default could be read from the hardware instead, but I didn't see
any reason to add this complexity.
This has been tested on an STM32F746.
Fixes: 85fdc63fe2 ("drivers: watchdog: stm32_iwdg: set WDOG_HW_RUNNING at probe")
Signed-off-by: Ben Wolsieffer <ben.wolsieffer@hefring.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240228182723.12855-1-ben.wolsieffer@hefring.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7af2df0f67 ]
In cfd66bb715 ("f2fs: fix deadloop in foreground GC"), we needed to check
the number of blocks in a section instead of the segment.
Fixes: cfd66bb715 ("f2fs: fix deadloop in foreground GC")
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea59b12ac6 ]
It needs to check compress flag w/ .i_sem lock, otherwise, compressed
inode may be disabled after the check condition, it's not needed to
set compress option on non-compress inode.
Fixes: e1e8debec6 ("f2fs: add F2FS_IOC_SET_COMPRESS_OPTION ioctl")
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bcac8bff90 ]
Switch order of operations to avoid creating a short XDR buffer:
e.g., buflen = 12, old xdrlen = 12, new xdrlen = 20.
Having a short XDR buffer leads to lxa_maxcount be a few bytes
less than what is needed to retrieve the whole list when using
a buflen as returned by a call with size = 0:
buflen = listxattr(path, NULL, 0);
buf = malloc(buflen);
buflen = listxattr(path, buf, buflen);
For a file with one attribute (name = '123456'), the first call
with size = 0 will return buflen = 12 ('user.123456\x00').
The second call with size = 12, sends LISTXATTRS with
lxa_maxcount = 12 + 8 (cookie) + 4 (array count) = 24. The
XDR buffer needs 8 (cookie) + 4 (array count) + 4 (name count)
+ 6 (name len) + 2 (padding) + 4 (eof) = 28 which is 4 bytes
shorter than the lxa_maxcount provided in the call.
Fixes: 04a5da690e ("NFSv4.2: define limits and sizes for user xattr handling")
Signed-off-by: Jorge Mora <mora@netapp.com>
Reviewed-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 251a658bbf ]
A call to listxattr() with a buffer size = 0 returns the actual
size of the buffer needed for a subsequent call. When size > 0,
nfs4_listxattr() does not return an error because either
generic_listxattr() or nfs4_listxattr_nfs4_label() consumes
exactly all the bytes then size is 0 when calling
nfs4_listxattr_nfs4_user() which then triggers the following
kernel BUG:
[ 99.403778] kernel BUG at mm/usercopy.c:102!
[ 99.404063] Internal error: Oops - BUG: 00000000f2000800 [#1] SMP
[ 99.408463] CPU: 0 PID: 3310 Comm: python3 Not tainted 6.6.0-61.fc40.aarch64 #1
[ 99.415827] Call trace:
[ 99.415985] usercopy_abort+0x70/0xa0
[ 99.416227] __check_heap_object+0x134/0x158
[ 99.416505] check_heap_object+0x150/0x188
[ 99.416696] __check_object_size.part.0+0x78/0x168
[ 99.416886] __check_object_size+0x28/0x40
[ 99.417078] listxattr+0x8c/0x120
[ 99.417252] path_listxattr+0x78/0xe0
[ 99.417476] __arm64_sys_listxattr+0x28/0x40
[ 99.417723] invoke_syscall+0x78/0x100
[ 99.417929] el0_svc_common.constprop.0+0x48/0xf0
[ 99.418186] do_el0_svc+0x24/0x38
[ 99.418376] el0_svc+0x3c/0x110
[ 99.418554] el0t_64_sync_handler+0x120/0x130
[ 99.418788] el0t_64_sync+0x194/0x198
[ 99.418994] Code: aa0003e3 d000a3e0 91310000 97f49bdb (d4210000)
Issue is reproduced when generic_listxattr() returns 'system.nfs4_acl',
thus calling lisxattr() with size = 16 will trigger the bug.
Add check on nfs4_listxattr() to return ERANGE error when it is
called with size > 0 and the return value is greater than size.
Fixes: 012a211abd ("NFSv4.2: hook in the user extended attribute handlers")
Signed-off-by: Jorge Mora <mora@netapp.com>
Reviewed-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d6f4de70f7 ]
The intent is to check if the strings' are truncated or not. So, >= should
be used instead of >, because strlcat() and snprintf() return the length of
the output, excluding the trailing NULL.
Fixes: a02d692611 ("SUNRPC: Provide functions for managing universal addresses")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e39602da75 ]
f2fs only support to config zstd compress level w/ a positive number due
to layout design, but since commit e0c1b49f5b ("lib: zstd: Upgrade to
latest upstream zstd version 1.4.10"), zstd supports negative compress
level, so that zstd_min_clevel() may return a negative number, then w/
below mount option, .compress_level can be configed w/ a negative number,
which is not allowed to f2fs, let's add check condition to avoid it.
mount -o compress_algorithm=zstd:4294967295 /dev/sdx /mnt/f2fs
Fixes: 00e120b5e4 ("f2fs: assign default compression level")
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b69600231f ]
Some callback functions used here take a boolean argument, others take a
status argument. This breaks KCFI type checking, so clang now warns about
the function pointer cast:
drivers/scsi/bfa/bfad_bsg.c:2138:29: error: cast from 'void (*)(void *, enum bfa_status)' to 'bfa_cb_cbfn_t' (aka 'void (*)(void *, enum bfa_boolean)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
Assuming the code is actually correct here and the callers always match the
argument types of the callee, rework this to replace the explicit cast with
a union of the two pointer types. This does not change the behavior of the
code, so if something is actually broken here, a larger rework may be
necessary.
Fixes: 37ea0558b8 ("[SCSI] bfa: Added support to collect and reset fcport stats")
Fixes: 3ec4f2c8bf ("[SCSI] bfa: Added support to configure QOS and collect stats.")
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240222124433.2046570-1-arnd@kernel.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a8bccd8b2 ]
The mad_client will be initialized in enable_device_and_get(), while the
devices_rwsem will be downgraded to a read semaphore. There is a window
that leads to the failed initialization for cm_client, since it can not
get matched mad port from ib_mad_port_list, and the matched mad port will
be added to the list after that.
mad_client | cm_client
------------------|--------------------------------------------------------
ib_register_device|
enable_device_and_get
down_write(&devices_rwsem)
xa_set_mark(&devices, DEVICE_REGISTERED)
downgrade_write(&devices_rwsem)
|
|ib_cm_init
|ib_register_client(&cm_client)
|down_read(&devices_rwsem)
|xa_for_each_marked (&devices, DEVICE_REGISTERED)
|add_client_context
|cm_add_one
|ib_register_mad_agent
|ib_get_mad_port
|__ib_get_mad_port
|list_for_each_entry(entry, &ib_mad_port_list, port_list)
|return NULL
|up_read(&devices_rwsem)
|
add_client_context|
ib_mad_init_device|
ib_mad_port_open |
list_add_tail(&port_priv->port_list, &ib_mad_port_list)
up_read(&devices_rwsem)
|
Fix it by using down_write(&devices_rwsem) in ib_register_client().
Fixes: d0899892ed ("RDMA/device: Provide APIs from the core code to help unregistration")
Link: https://lore.kernel.org/r/20240203035313.98991-1-lishifeng@sangfor.com.cn
Suggested-by: Jason Gunthorpe <jgg@ziepe.ca>
Signed-off-by: Shifeng Li <lishifeng@sangfor.com.cn>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d20a7cf9f7 ]
Commit 27c5fd271d ("RDMA/hns: The UD mode can only be configured
with DCQCN") adds a check of congest control alorithm for UD. But
that patch causes a problem: hr_dev->caps.congest_type is global,
used by all QPs, so modifying this field to DCQCN for UD QPs causes
other QPs unable to use any other algorithm except DCQCN.
Revert the modification in commit 27c5fd271d ("RDMA/hns: The UD
mode can only be configured with DCQCN"). Add a new field cong_type
to struct hns_roce_qp and configure DCQCN for UD QPs.
Fixes: 27c5fd271d ("RDMA/hns: The UD mode can only be configured with DCQCN")
Fixes: f91696f2f0 ("RDMA/hns: Support congestion control type selection according to the FW")
Signed-off-by: Luoyouming <luoyouming@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://lore.kernel.org/r/20240219061805.668170-1-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f3dbcb563 ]
csiostor uses function pointer casts to keep the csio_ln_ev state machine
hidden, but this causes warnings about control flow integrity (KCFI)
violations in clang-16 and higher:
drivers/scsi/csiostor/csio_lnode.c:1098:33: error: cast from 'void (*)(struct csio_lnode *, enum csio_ln_ev)' to 'csio_sm_state_t' (aka 'void (*)(void *, unsigned int)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
1098 | return (csio_get_state(ln) == ((csio_sm_state_t)csio_lns_ready));
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/csiostor/csio_lnode.c:1369:29: error: cast from 'void (*)(struct csio_lnode *, enum csio_ln_ev)' to 'csio_sm_state_t' (aka 'void (*)(void *, unsigned int)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
1369 | if (csio_get_state(ln) == ((csio_sm_state_t)csio_lns_uninit)) {
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/csiostor/csio_lnode.c:1373:29: error: cast from 'void (*)(struct csio_lnode *, enum csio_ln_ev)' to 'csio_sm_state_t' (aka 'void (*)(void *, unsigned int)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
1373 | if (csio_get_state(ln) == ((csio_sm_state_t)csio_lns_ready)) {
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/csiostor/csio_lnode.c:1377:29: error: cast from 'void (*)(struct csio_lnode *, enum csio_ln_ev)' to 'csio_sm_state_t' (aka 'void (*)(void *, unsigned int)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
1377 | if (csio_get_state(ln) == ((csio_sm_state_t)csio_lns_offline)) {
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Move the enum into a shared header so the correct types can be used without
the need for casts.
Fixes: a3667aaed5 ("[SCSI] csiostor: Chelsio FCoE offload driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240213100518.457623-1-arnd@kernel.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21ec682348 ]
During recovery, if FAULT_BLOCK is on, it is possible that
f2fs_reserve_new_block() will return -ENOSPC during recovery,
then it may trigger panic.
Also, if fault injection rate is 1 and only FAULT_BLOCK fault
type is on, it may encounter deadloop in loop of block reservation.
Let's change as below to fix these issues:
- remove bug_on() to avoid panic.
- limit the loop count of block reservation to avoid potential
deadloop.
Fixes: 956fa1ddc1 ("f2fs: fix to check return value of f2fs_reserve_new_block()")
Reported-by: Zhiguo Niu <zhiguo.niu@unisoc.com>
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2034ef619 ]
BUG: kernel NULL pointer dereference, address: 0000000000000014
RIP: 0010:f2fs_submit_page_write+0x6cf/0x780 [f2fs]
Call Trace:
<TASK>
? show_regs+0x6e/0x80
? __die+0x29/0x70
? page_fault_oops+0x154/0x4a0
? prb_read_valid+0x20/0x30
? __irq_work_queue_local+0x39/0xd0
? irq_work_queue+0x36/0x70
? do_user_addr_fault+0x314/0x6c0
? exc_page_fault+0x7d/0x190
? asm_exc_page_fault+0x2b/0x30
? f2fs_submit_page_write+0x6cf/0x780 [f2fs]
? f2fs_submit_page_write+0x736/0x780 [f2fs]
do_write_page+0x50/0x170 [f2fs]
f2fs_outplace_write_data+0x61/0xb0 [f2fs]
f2fs_do_write_data_page+0x3f8/0x660 [f2fs]
f2fs_write_single_data_page+0x5bb/0x7a0 [f2fs]
f2fs_write_cache_pages+0x3da/0xbe0 [f2fs]
...
It is possible that other threads have added this fio to io->bio
and submitted the io->bio before entering f2fs_submit_page_write().
At this point io->bio = NULL.
If is_end_zone_blkaddr(sbi, fio->new_blkaddr) of this fio is true,
then an NULL pointer dereference error occurs at bio_get(io->bio).
The original code for determining zone end was after "out:",
which would have missed some fio who is zone end. I've moved
this code before "skip:" to make sure it's done for each fio.
Fixes: e067dc3c6b ("f2fs: maintain six open zones for zoned devices")
Signed-off-by: Wenjie Qi <qwjhust@gmail.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 536af82115 ]
It needs to check last zone_pending_bio and wait IO completion before
traverse next fio in io->io_list, otherwise, bio in next zone may be
submitted before all IO completion in current zone.
Fixes: e067dc3c6b ("f2fs: maintain six open zones for zoned devices")
Cc: Daeho Jeong <daehojeong@google.com>
Signed-off-by: Chao Yu <chao@kernel.org>
Reviewed-by: Daeho Jeong <daehojeong@google.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b896e302f7 ]
verify_blkaddr() will trigger panic once we inject fault into
f2fs_is_valid_blkaddr(), fix to remove this unnecessary f2fs_bug_on().
Fixes: 18792e64c8 ("f2fs: support fault injection for f2fs_is_valid_blkaddr()")
Reviewed-by: Daeho Jeong <daehojeong@google.com>
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5460749487 ]
In reserve_compress_blocks(), we update blkaddrs of dnode in prior to
inc_valid_block_count(), it may cause inconsistent status bewteen
i_blocks and blkaddrs once inc_valid_block_count() fails.
To fix this issue, it needs to reverse their invoking order.
Fixes: c75488fb4d ("f2fs: introduce F2FS_IOC_RESERVE_COMPRESS_BLOCKS")
Reviewed-by: Daeho Jeong <daehojeong@google.com>
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59d0d4c3ea ]
This patch allows caller to pass blkaddr to f2fs_set_data_blkaddr()
and let __set_data_blkaddr() inside f2fs_set_data_blkaddr() to update
dn->data_blkaddr w/ last value of blkaddr.
Just cleanup, no logic changes.
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Stable-dep-of: 5460749487 ("f2fs: compress: fix to avoid inconsistence bewteen i_blocks and dnode")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a539363613 ]
Commit 3c6c2bebef ("f2fs: avoid punch_hole overhead when releasing
volatile data") introduced FI_FIRST_BLOCK_WRITTEN as below reason:
This patch is to avoid some punch_hole overhead when releasing volatile
data. If volatile data was not written yet, we just can make the first
page as zero.
After commit 7bc155fec5 ("f2fs: kill volatile write support"), we
won't support volatile write, but it missed to remove obsolete
FI_FIRST_BLOCK_WRITTEN, delete it in this patch.
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Stable-dep-of: 5460749487 ("f2fs: compress: fix to avoid inconsistence bewteen i_blocks and dnode")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb8fbaa533 ]
Compressed cluster may not be released due to we can fail in
release_compress_blocks(), fix to handle reserved compressed
cluster correctly in reserve_compress_blocks().
Fixes: 4c8ff7095b ("f2fs: support data compression")
Signed-off-by: Sheng Yong <shengyong@oppo.com>
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd244524c2 ]
When we overwrite compressed cluster w/ normal cluster, we should
not unlock cp_rwsem during f2fs_write_raw_pages(), otherwise data
will be corrupted if partial blocks were persisted before CP & SPOR,
due to cluster metadata wasn't updated atomically.
Fixes: 4c8ff7095b ("f2fs: support data compression")
Reviewed-by: Daeho Jeong <daehojeong@google.com>
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a430dd49e ]
If data block in compressed cluster is not persisted with metadata
during checkpoint, after SPOR, the data may be corrupted, let's
guarantee to write compressed page by checkpoint.
Fixes: 4c8ff7095b ("f2fs: support data compression")
Reviewed-by: Daeho Jeong <daehojeong@google.com>
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c21a8870c9 ]
Upon rare occasions, KASAN reports a use-after-free Write
in srpt_refresh_port().
This seems to be because an event handler is registered before the
srpt device is fully setup and a race condition upon error may leave a
partially setup event handler in place.
Instead, only register the event handler after srpt device initialization
is complete.
Fixes: a42d985bd5 ("ib_srpt: Initial SRP Target merge for v3.3-rc1")
Signed-off-by: William Kucharski <william.kucharski@oracle.com>
Link: https://lore.kernel.org/r/20240202091549.991784-2-william.kucharski@oracle.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f51de7e30 ]
The runtime_resume function calls prmg_load and apply_calibration
functions, but system_resume also calls them, so calling
pm_runtime_force_resume before reset is unnecessary.
For consistency, do not call the pm_runtime_force_suspend in
system_suspend, as runtime_suspend does the same.
Fixes: 5be27f1e3e ("ALSA: hda/tas2781: Add tas2781 HDA driver")
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <d0b4cc1248b9d375d59c009563da42d60d69eac3.1709918447.git.soyer@irl.hu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bec7760a6c ]
The amplifier doesn't loose register state in software shutdown mode, so
there is no need to reset the cur_* values.
Without these resets, the amplifier can be turned on after
runtime_suspend without waiting for the program and
profile to be restored.
Fixes: 5be27f1e3e ("ALSA: hda/tas2781: Add tas2781 HDA driver")
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <aa27ae084150988bf6a0ead7e3403bc485d790f8.1709918447.git.soyer@irl.hu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c062166995 ]
Realtek codec on HP Envy laptop series are heavily modified by vendor.
Therefore, need intervention to make it work properly. The patch fixes:
- B&O soundbar speakers (between lid and keyboard) activation
- Enable LED on mute button
- Add missing process coefficient which affects the output amplifier
- Volume control synchronization between B&O soundbar and side speakers
- Unmute headset output on several HP Envy models
- Auto-enable headset mic when plugged
This patch was tested on HP Envy x360 13-AR0107AU with Realtek ALC285
The only unsolved problem is output amplifier of all built-in speakers
is too weak, which causes volume of built-in speakers cannot be loud
as vendor's proprietary driver due to missing _DSD parameter in the
firmware. The solution is currently on research. Expected to has another
patch in the future.
Potential fix to related issues, need test before close those issues:
- https://bugzilla.kernel.org/show_bug.cgi?id=189331
- https://bugzilla.kernel.org/show_bug.cgi?id=216632
- https://bugzilla.kernel.org/show_bug.cgi?id=216311
- https://bugzilla.kernel.org/show_bug.cgi?id=213507
Signed-off-by: Athaariq Ardhiansyah <foss@athaariq.my.id>
Message-ID: <20240310140249.3695-1-foss@athaariq.my.id>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3dc1bdb6b ]
cifs writeback doesn't correctly handle the case where
cifs_extend_writeback() hits a point where it is considering an additional
folio, but this would overrun the wsize - at which point it drops out of
the xarray scanning loop and calls xas_pause(). The problem is that
xas_pause() advances the loop counter - thereby skipping that page.
What needs to happen is for xas_reset() to be called any time we decide we
don't want to process the page we're looking at, but rather send the
request we are building and start a new one.
Fix this by copying and adapting the netfslib writepages code as a
temporary measure, with cifs writeback intending to be offloaded to
netfslib in the near future.
This also fixes the issue with the use of filemap_get_folios_tag() causing
retry of a bunch of pages which the extender already dealt with.
This can be tested by creating, say, a 64K file somewhere not on cifs
(otherwise copy-offload may get underfoot), mounting a cifs share with a
wsize of 64000, copying the file to it and then comparing the original file
and the copy:
dd if=/dev/urandom of=/tmp/64K bs=64k count=1
mount //192.168.6.1/test /mnt -o user=...,pass=...,wsize=64000
cp /tmp/64K /mnt/64K
cmp /tmp/64K /mnt/64K
Without the fix, the cmp fails at position 64000 (or shortly thereafter).
Fixes: d08089f649 ("cifs: Change the I/O paths to use an iterator rather than a page list")
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Steve French <sfrench@samba.org>
cc: Paulo Alcantara <pc@manguebit.com>
cc: Ronnie Sahlberg <ronniesahlberg@gmail.com>
cc: Shyam Prasad N <sprasad@microsoft.com>
cc: Tom Talpey <tom@talpey.com>
cc: Jeff Layton <jlayton@kernel.org>
cc: linux-cifs@vger.kernel.org
cc: samba-technical@lists.samba.org
cc: netfs@lists.linux.dev
cc: linux-fsdevel@vger.kernel.org
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c40497d823 ]
Filesystems should use folio->index and folio->mapping, instead of
folio_index(folio), folio_mapping() and folio_file_mapping() since
they know that it's in the pagecache.
Change this automagically with:
perl -p -i -e 's/folio_mapping[(]([^)]*)[)]/\1->mapping/g' fs/smb/client/*.c
perl -p -i -e 's/folio_file_mapping[(]([^)]*)[)]/\1->mapping/g' fs/smb/client/*.c
perl -p -i -e 's/folio_index[(]([^)]*)[)]/\1->index/g' fs/smb/client/*.c
Reported-by: Matthew Wilcox <willy@infradead.org>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Jeff Layton <jlayton@kernel.org>
cc: Steve French <sfrench@samba.org>
cc: Paulo Alcantara <pc@manguebit.com>
cc: Ronnie Sahlberg <lsahlber@redhat.com>
cc: Shyam Prasad N <sprasad@microsoft.com>
cc: Tom Talpey <tom@talpey.com>
cc: linux-cifs@vger.kernel.org
cc: linux-fsdevel@vger.kernel.org
Stable-dep-of: f3dc1bdb6b ("cifs: Fix writeback data corruption")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e97fe4901e ]
It is possible for clk_core_get to dereference a NULL in the following
sequence:
clk_core_get()
of_clk_get_hw_from_clkspec()
__of_clk_get_hw_from_provider()
__clk_get_hw()
__clk_get_hw() can return NULL which is dereferenced by clk_core_get() at
hw->core.
Prior to commit dde4eff47c ("clk: Look for parents with clkdev based
clk_lookups") the check IS_ERR_OR_NULL() was performed which would have
caught the NULL.
Reading the description of this function it talks about returning NULL but
that cannot be so at the moment.
Update the function to check for hw before dereferencing it and return NULL
if hw is NULL.
Fixes: dde4eff47c ("clk: Look for parents with clkdev based clk_lookups")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20240302-linux-next-24-03-01-simple-clock-fixes-v1-1-25f348a5982b@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20933531be ]
Move the prototypes into mpc10x.h which is included by all the relevant
C files, fixes:
arch/powerpc/platforms/embedded6xx/ls_uart.c:59:6: error: no previous prototype for 'avr_uart_configure'
arch/powerpc/platforms/embedded6xx/ls_uart.c:82:6: error: no previous prototype for 'avr_uart_send'
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20240305123410.3306253-1-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f8cd6c0a4 ]
The synchronization here is to ensure the ordering of freeing of a module
init so that it happens before W+X checking. It is worth noting it is not
that the freeing was not happening, it is just that our sanity checkers
raced against the permission checkers which assume init memory is already
gone.
Commit 1a7b7d9220 ("modules: Use vmalloc special flag") moved calling
do_free_init() into a global workqueue instead of relying on it being
called through call_rcu(..., do_free_init), which used to allowed us call
do_free_init() asynchronously after the end of a subsequent grace period.
The move to a global workqueue broke the gaurantees for code which needed
to be sure the do_free_init() would complete with rcu_barrier(). To fix
this callers which used to rely on rcu_barrier() must now instead use
flush_work(&init_free_wq).
Without this fix, we still could encounter false positive reports in W+X
checking since the rcu_barrier() here can not ensure the ordering now.
Even worse, the rcu_barrier() can introduce significant delay. Eric
Chanudet reported that the rcu_barrier introduces ~0.1s delay on a
PREEMPT_RT kernel.
[ 0.291444] Freeing unused kernel memory: 5568K
[ 0.402442] Run /sbin/init as init process
With this fix, the above delay can be eliminated.
Link: https://lkml.kernel.org/r/20240227023546.2490667-1-changbin.du@huawei.com
Fixes: 1a7b7d9220 ("modules: Use vmalloc special flag")
Signed-off-by: Changbin Du <changbin.du@huawei.com>
Tested-by: Eric Chanudet <echanude@redhat.com>
Acked-by: Luis Chamberlain <mcgrof@kernel.org>
Cc: Xiaoyi Su <suxiaoyi@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11b752ac5a ]
The following table shows the values of the 'halt_reg' and the
'enable_reg' fields from the pcie clocks defined in the current
driver:
clock halt_reg enable_reg
gcc_pcie0_ahb_clk 0x75010 0x75010
gcc_pcie0_aux_clk 0x75014 0x75014
gcc_pcie0_axi_m_clk 0x75008 0x75008
gcc_pcie0_axi_s_bridge_clk 0x75048 0x75048
gcc_pcie0_axi_s_clk 0x7500c 0x7500c
gcc_pcie0_pipe_clk 0x75018 0x75018
gcc_pcie1_ahb_clk 0x76010 0x76010
gcc_pcie1_aux_clk 0x76014 0x76014
gcc_pcie1_axi_m_clk 0x76008 0x76008
gcc_pcie1_axi_s_bridge_clk 0x76048 0x76048
gcc_pcie1_axi_s_clk 0x7600c 0x7600c
gcc_pcie1_pipe_clk 8* 0x76018
Based on the table, it is quite likely that the pcie0 and the pci1
clocks are using the same register layout, however it seems that
the value of the 'halt_reg' field in the 'gcc_pcie1_pipe_clk' clock
is wrong.
In the downstream driver [1], the same '0x76018' value is used for
both the 'halt_reg' and for the 'enable_reg' fields of the
'gcc_pcie1_pipe_clk' clock.
Update the current driver to use the same value used downstream as
probably that is the correct value.
1. https://git.codelinaro.org/clo/qsdk/oss/kernel/linux-ipq-5.4/-/blob/NHSS.QSDK.12.4.r4/drivers/clk/qcom/gcc-ipq5018.c?ref_type=heads#L2316
Fixes: e3fdbef1ba ("clk: qcom: Add Global Clock controller (GCC) driver for IPQ5018")
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Kathiravan Thirumoorthy <quic_kathirav@quicinc.com>
Link: https://lore.kernel.org/r/20240225-gcc-ipq5018-register-fixes-v1-2-3c191404d9f0@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f982adcc1b ]
The value of the 'enable_reg' field in the 'gcc_gmac0_sys_clk'
clock definition seems wrong as it is greater than the
'max_register' value defined in the regmap configuration.
Additionally, all other gmac specific branch clock definitions
within the driver uses the same value both for the 'enable_reg'
and for the 'halt_reg' fields.
Due to the lack of documentation the correct value is not known.
Looking into the downstream driver does not help either, as that
uses the same (presumably wrong) value [1].
Nevertheless, change the 'enable_reg' field of 'gcc_gmac0_sys_clk'
to use the value from the 'halt_reg' field so it follows the pattern
used in other gmac clock definitions. The change is based on the
assumption that the register layout of this clock is the same
as the other gmac clocks.
1. https://git.codelinaro.org/clo/qsdk/oss/kernel/linux-ipq-5.4/-/blob/NHSS.QSDK.12.4.r4/drivers/clk/qcom/gcc-ipq5018.c?ref_type=heads#L1889
Fixes: e3fdbef1ba ("clk: qcom: Add Global Clock controller (GCC) driver for IPQ5018")
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Kathiravan Thirumoorthy <quic_kathirav@quicinc.com>
Link: https://lore.kernel.org/r/20240225-gcc-ipq5018-register-fixes-v1-1-3c191404d9f0@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad86d7ee43 ]
Running event hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles,phys_processor_idx=0/
in one of the system throws below error:
---Logs---
# perf list | grep hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles
hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles,phys_processor_idx=?/[Kernel PMU event]
# perf stat -v -e hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles,phys_processor_idx=0/ sleep 2
Using CPUID 00800200
Control descriptor is not initialized
Warning:
hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles,phys_processor_idx=0/ event is not supported by the kernel.
failed to read counter hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles,phys_processor_idx=0/
Performance counter stats for 'system wide':
<not supported> hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles,phys_processor_idx=0/
2.000700771 seconds time elapsed
The above error is because of the hcall failure as required
permission "Enable Performance Information Collection" is not set.
Based on current code, single_gpci_request function did not check the
error type incase hcall fails and by default returns EINVAL. But we can
have other reasons for hcall failures like H_AUTHORITY/H_PARAMETER with
detail_rc as GEN_BUF_TOO_SMALL, for which we need to act accordingly.
Fix this issue by adding new checks in the single_gpci_request and
h_gpci_event_init functions.
Result after fix patch changes:
# perf stat -e hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles,phys_processor_idx=0/ sleep 2
Error:
No permission to enable hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles,phys_processor_idx=0/ event.
Fixes: 220a0c609a ("powerpc/perf: Add support for the hv gpci (get performance counter info) interface")
Reported-by: Akanksha J N <akanksha@linux.ibm.com>
Signed-off-by: Kajol Jain <kjain@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20240229122847.101162-1-kjain@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c958e86e9c ]
It's possible that mtk_crtc->event is NULL in
mtk_drm_crtc_finish_page_flip().
pending_needs_vblank value is set by mtk_crtc->event, but in
mtk_drm_crtc_atomic_flush(), it's is not guarded by the same
lock in mtk_drm_finish_page_flip(), thus a race condition happens.
Consider the following case:
CPU1 CPU2
step 1:
mtk_drm_crtc_atomic_begin()
mtk_crtc->event is not null,
step 1:
mtk_drm_crtc_atomic_flush:
mtk_drm_crtc_update_config(
!!mtk_crtc->event)
step 2:
mtk_crtc_ddp_irq ->
mtk_drm_finish_page_flip:
lock
mtk_crtc->event set to null,
pending_needs_vblank set to false
unlock
pending_needs_vblank set to true,
step 2:
mtk_crtc_ddp_irq ->
mtk_drm_finish_page_flip called again,
pending_needs_vblank is still true
//null pointer
Instead of guarding the entire mtk_drm_crtc_atomic_flush(), it's more
efficient to just check if mtk_crtc->event is null before use.
Fixes: 119f517362 ("drm/mediatek: Add DRM Driver for Mediatek SoC MT8173.")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20240223212404.3709690-1-hsinyi@chromium.org/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 53cf6b72e0 ]
Previously, the statement looked like:
slpm[x] &= ~BIT(g->grp.pins[i]);
Where:
- slpm is a unsigned int pointer;
- g->grp.pins[i] is a pin number. It can grow to more than 32.
The expected shift amount is a pin bank offset.
This bug does not occur on every group or pin: the altsetting must be
NMK_GPIO_ALT_C and the pin must be 32 or above. It might have occured.
For example, in pinctrl-nomadik-db8500.c, pin group i2c3_c_2 has the
right altsetting and pins 229 and 230.
Fixes: dbfe8ca259 ("pinctrl/nomadik: implement pin multiplexing")
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20240228-mbly-gpio-v2-5-3ba757474006@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b485b899e5 ]
Fix mask used for esm ctrl register to get pcie link
speed on smu_v11_0_3, smu_v13_0_2 & smu_v13_0_6
Fixes: 511a95552e ("drm/amd/pm: Add SMU 13.0.6 support")
Fixes: c05d1c4015 ("drm/amd/swsmu: add aldebaran smu13 ip support (v3)")
Fixes: f1c3785931 ("drm/amd/powerplay: add Arcturus support for gpu metrics export")
Signed-off-by: Asad Kamal <asad.kamal@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Le Ma <le.ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bfb1b99802 ]
The ipi handler here tries hard to maintain const-ness of its argument,
but by doing that causes a warning about function type casts:
drivers/media/platform/mediatek/vcodec/common/mtk_vcodec_fw_vpu.c:38:32: error: cast from 'mtk_vcodec_ipi_handler' (aka 'void (*)(void *, unsigned int, void *)') to 'ipi_handler_t' (aka 'void (*)(const void *, unsigned int, void *)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
38 | ipi_handler_t handler_const = (ipi_handler_t)handler;
| ^~~~~~~~~~~~~~~~~~~~~~
Remove the hack and just use a non-const argument.
Fixes: bf1d556ad4 ("media: mtk-vcodec: abstract firmware interface")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d0b07f712b ]
When saa7146_register_device and saa7146_vv_init fails, budget_av_attach
should free the resources it allocates, like the error-handling of
ttpci_budget_init does. Besides, there are two fixme comment refers to
such deallocations.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b9b683844b ]
In go7007_load_encoder, bounce(i.e. go->boot_fw), is allocated without
a deallocation thereafter. After the following call chain:
saa7134_go7007_init
|-> go7007_boot_encoder
|-> go7007_load_encoder
|-> kfree(go)
go is freed and thus bounce is leaked.
Fixes: 95ef39403f ("[media] go7007: remember boot firmware")
Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a4cf27d1f ]
A previous patch worked around a KASAN issue in stv0367, now a similar
problem showed up with clang:
drivers/media/dvb-frontends/stv0367.c:1222:12: error: stack frame size (3624) exceeds limit (2048) in 'stv0367ter_set_frontend' [-Werror,-Wframe-larger-than]
1214 | static int stv0367ter_set_frontend(struct dvb_frontend *fe)
Rework the stv0367_writereg() function to be simpler and mark both
register access functions as noinline_for_stack so the temporary
i2c_msg structures do not get duplicated on the stack when KASAN_STACK
is enabled.
Fixes: 3cd890dbe2 ("media: dvb-frontends: fix i2c access helpers for KASAN")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Justin Stitt <justinstitt@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bbf0dec306 ]
HPD sensor data is not populating properly because of wrong order of HPD
sensor structure elements. So update the order of structure elements to
match the HPD sensor data received from the firmware.
Fixes: 24a31ea949 ("HID: amd_sfh: Add initial support for HPD sensor")
Co-developed-by: Akshata MukundShetty <akshata.mukundshetty@amd.com>
Signed-off-by: Akshata MukundShetty <akshata.mukundshetty@amd.com>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59c6a3a43b ]
According to Amlogic datasheets for the SoCs supported by this driver, the
maximum bit clock rate is 100MHz.
The tdm interface allows the rates listed by the DAI driver, regardless of
the number slots or their width. However, these will impact the bit clock
rate.
Hitting the 100MHz limit is very unlikely for most use cases but it is
possible.
For example with 32 slots / 32 bits wide, the maximum rate is no longer
384kHz but ~96kHz.
Add the constraint accordingly if the component is not already active.
If it is active, the rate is already constrained by the first stream rate.
Fixes: d60e4f1e4b ("ASoC: meson: add tdm interface driver")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://msgid.link/r/20240223175116.2005407-3-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3741a8d28 ]
By default, when mclk-fs is not provided, the tdm-interface driver
requests an MCLK that is 4x the bit clock, SCLK.
However there is no justification for this:
* If the codec needs MCLK for its operation, mclk-fs is expected to be set
according to the codec requirements.
* If the codec does not need MCLK the minimum is 2 * SCLK, because this is
minimum the divider between SCLK and MCLK can do.
Multiplying by 4 may cause problems because the PLL limit may be reached
sooner than it should, so use 2x instead.
Fixes: d60e4f1e4b ("ASoC: meson: add tdm interface driver")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://msgid.link/r/20240223175116.2005407-2-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 347b828882 ]
clang-16 warns about mismatched function prototypes:
drivers/mtd/nand/raw/lpc32xx_mlc.c:783:29: error: cast from 'irqreturn_t (*)(int, struct lpc32xx_nand_host *)' (aka 'enum irqreturn (*)(int, struct lpc32xx_nand_host *)') to 'irq_handler_t' (aka 'enum irqreturn (*)(int, void *)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
Change the interrupt handler to the normal way of just passing
a void* pointer and converting it inside the function..
Fixes: 70f7cb78ec ("mtd: add LPC32xx MLC NAND driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240213100146.455811-1-arnd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c079e2e113 ]
A sync lost issue can be observed with two displays, when moving a plane
from one disabled display to an another disabled display, and then
enabling the display to which the plane was moved to. The exact
requirements for this to trigger are not clear.
It looks like the issue is that the layers are left enabled in the first
display's OVR registers. Even if the corresponding VP is disabled, it
still causes an issue, as if the disabled VP and its OVR would still be
in use, leading to the same VID being used by two OVRs. However, this is
just speculation based on testing the DSS behavior.
Experimentation shows that as a workaround, we can disable all the
layers in the OVR when disabling a VP. There should be no downside to
this, as the OVR is anyway effectively disabled if its VP is disabled,
and it seems to solve the sync lost issue.
However, there may be a bigger issue in play here, related to J721e
erratum i2097 ("DSS: Disabling a Layer Connected to Overlay May Result
in Synclost During the Next Frame"). Experimentation also shows that the
OVR's CHANNELIN field has similar issue. So we may need to revisit this
when we find out more about the core issue.
Fixes: 32a1795f57 ("drm/tidss: New driver for TI Keystone platform Display SubSystem")
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240213-tidss-fixes-v1-2-d709e8dfa505@ideasonboard.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ec948ccb2 ]
When the driver sets up the zpos property it sets the default zpos value
to the HW id of the plane. That is fine as such, but as on many DSS
versions the driver arranges the DRM planes in a different order than
the HW planes (to keep the non-scalable planes first), this leads to odd
initial zpos values. An example is J721e, where the initial zpos values
for DRM planes are 1, 3, 0, 2.
In theory the userspace should configure the zpos values properly when
using multiple planes, and in that sense the initial zpos values
shouldn't matter, but there's really no reason not to fix this and help
the userspace apps which don't handle zpos perfectly. In particular,
some versions of Weston seem to have issues dealing with the planes
with the current default zpos values.
So let's change the zpos values for the DRM planes to 0, 1, 2, 3.
Another option would be to configure the planes marked as primary planes
to zpos 0. On a two display system this would give us plane zpos values
of 0, 0, 1, 2. The end result and behavior would be very similar in this
option, and I'm not aware that this would actually help us in any way.
So, to keep the code simple, I opted for the 0, 1, 2, 3 values.
Fixes: 32a1795f57 ("drm/tidss: New driver for TI Keystone platform Display SubSystem")
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240213-tidss-fixes-v1-1-d709e8dfa505@ideasonboard.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df018f8200 ]
If a device is configured for data compression chaining (dcc), half of the
engines are loaded with the symmetric crypto image and the rest are loaded
with the compression image.
However, in such configuration all rings can handle compression requests.
Fix the ring to service mapping so that when a device is configured for
dcc, the ring to service mapping reports that all rings in a bank can
be used for compression.
Fixes: a238487f79 ("crypto: qat - fix ring to service map for QAT GEN4")
Signed-off-by: Damian Muszynski <damian.muszynski@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4db87a5f9e ]
Move the function get_service_enabled() from adf_4xxx_hw_data.c to
adf_cfg_services.c and rename it as adf_get_service_enabled().
This function is not specific to the 4xxx and will be used by
other QAT drivers.
This does not introduce any functional change.
Signed-off-by: Jie Wang <jie.wang@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Stable-dep-of: df018f8200 ("crypto: qat - fix ring to service map for dcc in 4xxx")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03c76e8e7a ]
The file adf_cfg_services.h cannot be included in header files since it
instantiates the structure adf_cfg_services. Move that structure to its
own file and export the symbol.
This does not introduce any functional change.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Damian Muszynski <damian.muszynski@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Stable-dep-of: df018f8200 ("crypto: qat - fix ring to service map for dcc in 4xxx")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f99fb7d660 ]
Check if delta_us is not zero and return -EINVAL if it is.
delta_us is unlikely to be zero as there is a sleep between the reads of
the two timestamps.
This is to fix the following warning when compiling the QAT driver
using clang scan-build:
drivers/crypto/intel/qat/qat_common/adf_clock.c:87:9: warning: Division by zero [core.DivideZero]
87 | temp = DIV_ROUND_CLOSEST_ULL(temp, delta_us);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: e2980ba57e ("crypto: qat - add measure clock frequency")
Signed-off-by: Adam Guerin <adam.guerin@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e8fca2f12 ]
Errors can potentially occur in the "processing" of PSP commands or
commands can be processed successfully but still return an error code in
the header.
This second case was being discarded because PSP communication worked but
the command returned an error code in the payload header.
Capture both cases and return them to the caller as -EIO for the caller
to investigate. The caller can detect the latter by looking at
`req->header->status`.
Reported-and-tested-by: Tim Van Patten <timvp@google.com>
Fixes: 7ccc4f4e2e ("crypto: ccp - Add support for an interface for platform features")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 53cc9baeb9 ]
clang-16 warns about casting between incompatible function types:
arch/arm/crypto/sha256_glue.c:37:5: error: cast from 'void (*)(u32 *, const void *, unsigned int)' (aka 'void (*)(unsigned int *, const void *, unsigned int)') to 'sha256_block_fn *' (aka 'void (*)(struct sha256_state *, const unsigned char *, int)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
37 | (sha256_block_fn *)sha256_block_data_order);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
arch/arm/crypto/sha512-glue.c:34:3: error: cast from 'void (*)(u64 *, const u8 *, int)' (aka 'void (*)(unsigned long long *, const unsigned char *, int)') to 'sha512_block_fn *' (aka 'void (*)(struct sha512_state *, const unsigned char *, int)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
34 | (sha512_block_fn *)sha512_block_data_order);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fix the prototypes for the assembler functions to match the typedef.
The code already relies on the digest being the first part of the
state structure, so there is no change in behavior.
Fixes: c80ae7ca37 ("crypto: arm/sha512 - accelerated SHA-512 using ARM generic ASM and NEON")
Fixes: b59e2ae369 ("crypto: arm/sha256 - move SHA-224/256 ASM/NEON implementation to base layer")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 25412c0364 ]
Currently the perf tool doesn't detect support for extended event types
on Apple M1/M2 systems, and will not auto-expand plain PERF_EVENT_TYPE
hardware events into per-PMU events. This is due to the detection of
extended event types not handling mandatory filters required by the
M1/M2 PMU driver.
PMU drivers and the core perf_events code can require that
perf_event_attr::exclude_* filters are configured in a specific way and
may reject certain configurations of filters, for example:
(a) Many PMUs lack support for any event filtering, and require all
perf_event_attr::exclude_* bits to be clear. This includes Alpha's
CPU PMU, and ARM CPU PMUs prior to the introduction of PMUv2 in
ARMv7,
(b) When /proc/sys/kernel/perf_event_paranoid >= 2, the perf core
requires that perf_event_attr::exclude_kernel is set.
(c) The Apple M1/M2 PMU requires that perf_event_attr::exclude_guest is
set as the hardware PMU does not count while a guest is running (but
might be extended in future to do so).
In is_event_supported(), we try to account for cases (a) and (b), first
attempting to open an event without any filters, and if this fails,
retrying with perf_event_attr::exclude_kernel set. We do not account for
case (c), or any other filters that drivers could theoretically require
to be set.
Thus is_event_supported() will fail to detect support for any events
targeting an Apple M1/M2 PMU, even where events would be supported with
perf_event_attr:::exclude_guest set.
Since commit:
82fe2e45cd ("perf pmus: Check if we can encode the PMU number in perf_event_attr.type")
... we use is_event_supported() to detect support for extended types,
with the PMU ID encoded into the perf_event_attr::type. As above, on an
Apple M1/M2 system this will always fail to detect that the event is
supported, and consequently we fail to detect support for extended types
even when these are supported, as they have been since commit:
5c81672865 ("arm_pmu: Add PERF_PMU_CAP_EXTENDED_HW_TYPE capability")
Due to this, the perf tool will not automatically expand plain
PERF_TYPE_HARDWARE events into per-PMU events, even when all the
necessary kernel support is present.
This patch updates is_event_supported() to additionally try opening
events with perf_event_attr::exclude_guest set, allowing support for
events to be detected on Apple M1/M2 systems. I believe that this is
sufficient for all contemporary CPU PMU drivers, though in future it may
be necessary to check for other combinations of filter bits.
I've deliberately changed the check to not expect a specific error code
for missing filters, as today ;the kernel may return a number of
different error codes for missing filters (e.g. -EACCESS, -EINVAL, or
-EOPNOTSUPP) depending on why and where the filter configuration is
rejected, and retrying for any error is more robust.
Note that this does not remove the need for commit:
a24d9d9dc0 ("perf parse-events: Make legacy events lower priority than sysfs/JSON")
... which is still necessary so that named-pmu/event/ events work on
kernels without extended type support, even if the event name happens to
be the same as a PERF_EVENT_TYPE_HARDWARE event (e.g. as is the case for
the M1/M2 PMU's 'cycles' and 'instructions' events).
Fixes: 82fe2e45cd ("perf pmus: Check if we can encode the PMU number in perf_event_attr.type")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Ian Rogers <irogers@google.com>
Tested-by: James Clark <james.clark@arm.com>
Tested-by: Marc Zyngier <maz@kernel.org>
Cc: Hector Martin <marcan@marcan.st>
Cc: James Clark <james.clark@arm.com>
Cc: John Garry <john.g.garry@oracle.com>
Cc: Leo Yan <leo.yan@linux.dev>
Cc: Mike Leach <mike.leach@linaro.org>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Thomas Richter <tmricht@linux.ibm.com>
Cc: Will Deacon <will@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Link: https://lore.kernel.org/r/20240126145605.1005472-1-mark.rutland@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d2b0680cf3 ]
of_parse_phandle() returns a device_node with refcount incremented, which
the callee needs to call of_node_put() on when done. We should only call
of_node_put() when the property argument is provided though as otherwise
nothing has taken a reference on the node.
Fixes: 45330bb434 ("mfd: syscon: Allow property as NULL in syscon_regmap_lookup_by_phandle")
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240220115012.471689-2-peter.griffin@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 48f5fd8967 ]
This patch swaps SINK and SOURCE pads of the MEI CSI sub-device. While
this does change the UAPI by swapping the pads, the driver has never been
usable in upstream kernel as the Intel IPU6 driver it depends on any
functionality has not yet been merged.
Fixes: 29006e196a ("media: pci: intel: ivsc: Add CSI submodule")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a65083fa66 ]
CLK_INFRA_SSPM_32K_SELF has the "f_f26m_ck" clock assigned as its parent.
This is inconsistent as the clock is part of a group that are all gates
without dividers, and this makes the kernel think it runs at 26 MHz.
After clarification from MediaTek engineers, the correct parent is
actually the system 32 KHz clock.
Fixes: 1eb8d61ac5 ("clk: mediatek: mt8183: Add back SSPM related clocks")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20240219105125.956278-1-wenst@chromium.org
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit baf67aefbe ]
Per PCIe r6.1, sec 2.2.6.2 and 7.5.3.4, a Requester may not use 8-bit Tags
unless its Extended Tag Field Enable is set, but all Receivers/Completers
must handle 8-bit Tags correctly regardless of their Extended Tag Field
Enable.
Some devices do not handle 8-bit Tags as Completers, so add a quirk for
them. If we find such a device, we disable Extended Tags for the entire
hierarchy to make peer-to-peer DMA possible.
The 3ware 9650SE seems to have issues with handling 8-bit tags. Mark it as
broken.
This fixes PCI Parity Errors like :
3w-9xxx: scsi0: ERROR: (0x06:0x000C): PCI Parity Error: clearing.
3w-9xxx: scsi0: ERROR: (0x06:0x000D): PCI Abort: clearing.
3w-9xxx: scsi0: ERROR: (0x06:0x000E): Controller Queue Error: clearing.
3w-9xxx: scsi0: ERROR: (0x06:0x0010): Microcontroller Error: clearing.
Link: https://lore.kernel.org/r/20240219132811.8351-1-joerg@wedekind.de
Fixes: 60db3a4d8c ("PCI: Enable PCIe Extended Tags if supported")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=202425
Signed-off-by: Jörg Wedekind <joerg@wedekind.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fae6f81550 ]
The register bits definitions for RGB666 formats are wrong in multiple
ways: first, in the DSI_PS_SEL bits region, the Packed 18-bits RGB666
format is selected with bit 1, while the Loosely Packed one is bit 2,
and second - the definition name "LOOSELY_PS_18BIT_RGB666" is wrong
because the loosely packed format is 24 bits instead!
Either way, functions mtk_dsi_ps_control_vact() and mtk_dsi_ps_control()
do not even agree on the DSI_PS_SEL bit to set in DSI_PSCTRL: one sets
loosely packed (24) on RGB666, the other sets packed (18), and the other
way around for RGB666_PACKED.
Fixing this entire stack of issues is done in one go:
- Use the correct bit for the Loosely Packed RGB666 definition
- Rename LOOSELY_PS_18BIT_RGB666 to LOOSELY_PS_24BIT_RGB666
- Change ps_bpp_mode in mtk_dsi_ps_control_vact() to set:
- Loosely Packed, 24-bits for MIPI_DSI_FMT_RGB666
- Packed, 18-bits for MIPI_DSI_FMT_RGB666_PACKED
Fixes: 2e54c14e31 ("drm/mediatek: Add DSI sub driver")
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20240215085316.56835-3-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f6aed043ee ]
In the first if statement, we're checking if 'replay' is NULL. But in
the second if statement, we're not checking if 'replay' is NULL again
before calling replay->funcs->replay_set_power_opt().
if (replay == NULL && force_static)
return false;
...
if (link->replay_settings.replay_feature_enabled &&
replay->funcs->replay_set_power_opt) {
replay->funcs->replay_set_power_opt(replay, *power_opts, panel_inst);
link->replay_settings.replay_power_opt_active = *power_opts;
}
If 'replay' is NULL, this will cause a null pointer dereference.
Fixes the below found by smatch:
drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_edp_panel_control.c:895 edp_set_replay_allow_active() error: we previously assumed 'replay' could be null (see line 887)
Fixes: c7ddc0a800 ("drm/amd/display: Add Functions to enable Freesync Panel Replay")
Cc: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Cc: Roman Li <roman.li@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Tom Chung <chiahsuan.chung@amd.com>
Suggested-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 30baa4a96b ]
clang-16 complains about a control flow integrity (KCFI) issue in pvrusb2,
which casts three different prototypes into pvr2_stream_callback:
drivers/media/usb/pvrusb2/pvrusb2-v4l2.c:1070:30: error: cast from 'void (*)(struct pvr2_v4l2_fh *)' to 'pvr2_stream_callback' (aka 'void (*)(void *)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
1070 | pvr2_stream_set_callback(sp,(pvr2_stream_callback)pvr2_v4l2_notify,fh);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/media/usb/pvrusb2/pvrusb2-context.c:110:6: error: cast from 'void (*)(struct pvr2_context *)' to 'void (*)(void *)' converts to incompatible function type [-Werror,-Wcast-function-type-strict]
110 | (void (*)(void *))pvr2_context_notify,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/media/usb/pvrusb2/pvrusb2-dvb.c:152:6: error: cast from 'void (*)(struct pvr2_dvb_adapter *)' to 'pvr2_stream_callback' (aka 'void (*)(void *)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
152 | (pvr2_stream_callback) pvr2_dvb_notify, adap);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Change the functions to actually take a void* argument so the cast is no longer
needed.
Fixes: bb8ce9d914 ("V4L/DVB (7682): pvrusb2-dvb: finish up stream & buffer handling")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 95ac1210fb ]
Pointer dip->stream cannot be NULL due to a shift, thus remove redundant
NULL check.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: c74e006268 ("V4L/DVB (5059): Pvrusb2: Be smarter about mode restoration")
Signed-off-by: Daniil Dulov <d.dulov@aladdin.ru>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b70530ee7 ]
If go7007_read_addr() returns error channel is not assigned a value.
In this case go to allocfail.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 866b8695d6 ("Staging: add the go7007 video driver")
Signed-off-by: Daniil Dulov <d.dulov@aladdin.ru>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 856525e8db ]
While there is no good explanation what this value does, vendor driver
uses value 31 for it. Align driver with it.
Fixes: a4260ea495 ("media: sun4i: Add H3 deinterlace driver")
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cff104e33b ]
According to user manual, reset line should be deasserted before clocks
are enabled. Also fix power down sequence to be reverse of that.
Fixes: a4260ea495 ("media: sun4i: Add H3 deinterlace driver")
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 794b581f8c ]
Currently coefficients are applied only once, since they don't change.
However, this is done before enable bit is set and thus it doesn't get
applied properly.
Fix that by applying coefficients after enable bit is set. While this
means that it will be done evey time, it doesn't bring much time
penalty.
Fixes: a4260ea495 ("media: sun4i: Add H3 deinterlace driver")
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a11887f7f ]
bit_size field holds size of slice, not slice + header. Because of HW
quirks, driver can't program in just slice, but also preceding header.
But that means that currently used bit_size is wrong (too small).
Instead, just use size of whole buffer. There is no harm in doing this.
Fixes: 86caab29da ("media: cedrus: Add HEVC/H.265 decoding support")
Suggested-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aebfdfe39b ]
If device_register() fails in ntb_register_device(), the device name
allocated by dev_set_name() should be freed. As per the comment in
device_register(), callers should use put_device() to give up the
reference in the error path. So fix this by calling put_device() in the
error path so that the name can be freed in kobject_cleanup().
As a result of this, put_device() in the error path of
ntb_register_device() is removed and the actual error is returned.
Fixes: a1bd3baeb2 ("NTB: Add NTB hardware abstraction layer")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20231201033057.1399131-1-yangyingliang@huaweicloud.com
[mani: reworded commit message]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c5aebb53b3 ]
arch_vmap_pud_supported() and arch_vmap_pmd_supported() are
expected to constant-fold to false when RADIX is not enabled.
Force inlining in order to avoid following failure which
leads to unexpected call of non-existing pud_set_huge() and
pmd_set_huge() on powerpc 8xx.
In function 'pud_huge_tests',
inlined from 'debug_vm_pgtable' at mm/debug_vm_pgtable.c:1399:2:
./arch/powerpc/include/asm/vmalloc.h:9:33: warning: inlining failed in call to 'arch_vmap_pud_supported.isra': call is unlikely and code size would grow [-Winline]
9 | #define arch_vmap_pud_supported arch_vmap_pud_supported
| ^~~~~~~~~~~~~~~~~~~~~~~
./arch/powerpc/include/asm/vmalloc.h:10:20: note: in expansion of macro 'arch_vmap_pud_supported'
10 | static inline bool arch_vmap_pud_supported(pgprot_t prot)
| ^~~~~~~~~~~~~~~~~~~~~~~
./arch/powerpc/include/asm/vmalloc.h:9:33: note: called from here
9 | #define arch_vmap_pud_supported arch_vmap_pud_supported
mm/debug_vm_pgtable.c:458:14: note: in expansion of macro 'arch_vmap_pud_supported'
458 | if (!arch_vmap_pud_supported(args->page_prot) ||
| ^~~~~~~~~~~~~~~~~~~~~~~
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202402131836.OU1TDuoi-lkp@intel.com/
Fixes: 8309c9d717 ("powerpc: inline huge vmap supported functions")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/bbd84ad52bf377e8d3b5865a906f2dc5d99964ba.1707832677.git.christophe.leroy@csgroup.eu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ad992c71b ]
clang-16 warns about casting functions to incompatible types, as is done
here to call clk_disable_unprepare:
sound/soc/meson/t9015.c:274:4: error: cast from 'void (*)(struct clk *)' to 'void (*)(void *)' converts to incompatible function type [-Werror,-Wcast-function-type-strict]
274 | (void(*)(void *))clk_disable_unprepare,
The pattern of getting, enabling and setting a disable callback for a
clock can be replaced with devm_clk_get_enabled(), which also fixes
this warning.
Fixes: 33901f5b9b ("ASoC: meson: add t9015 internal DAC driver")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Justin Stitt <justinstitt@google.com>
Link: https://msgid.link/r/20240213215807.3326688-3-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 98ac85a00f ]
clang-16 warns about casting functions to incompatible types, as is done
here to call clk_disable_unprepare:
sound/soc/meson/aiu.c:243:12: error: cast from 'void (*)(struct clk *)' to 'void (*)(void *)' converts to incompatible function type [-Werror,-Wcast-function-type-strict]
243 | (void(*)(void *))clk_disable_unprepare,
The pattern of getting, enabling and setting a disable callback for a
clock can be replaced with devm_clk_get_enabled(), which also fixes
this warning.
Fixes: 6ae9ca9ce9 ("ASoC: meson: aiu: add i2s and spdif support")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Justin Stitt <justinstitt@google.com>
Link: https://msgid.link/r/20240213215807.3326688-2-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7bf738098 ]
clang-16 points out a control flow integrity (kcfi) issue when event
callbacks get converted to incompatible types:
sound/core/seq/seq_midi.c:135:30: error: cast from 'int (*)(struct snd_rawmidi_substream *, const char *, int)' to 'snd_seq_dump_func_t' (aka 'int (*)(void *, void *, int)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
135 | snd_seq_dump_var_event(ev, (snd_seq_dump_func_t)dump_midi, substream);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
sound/core/seq/seq_virmidi.c:83:31: error: cast from 'int (*)(struct snd_rawmidi_substream *, const unsigned char *, int)' to 'snd_seq_dump_func_t' (aka 'int (*)(void *, void *, int)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
83 | snd_seq_dump_var_event(ev, (snd_seq_dump_func_t)snd_rawmidi_receive, vmidi->substream);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
For addressing those errors, introduce wrapper functions that are used
for callbacks and bridge to the actual function call with pointer
cast.
The code was originally added with the initial ALSA merge in linux-2.5.4.
[ the patch description shamelessly copied from Arnd's original patch
-- tiwai ]
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240213101020.459183-1-arnd@kernel.org
Link: https://lore.kernel.org/r/20240213135343.16411-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2a3cfb9a24 ]
Since 'adev->dm.dc' in amdgpu_dm_fini() might turn out to be NULL
before the call to dc_enable_dmub_notifications(), check
beforehand to ensure there will not be a possible NULL-ptr-deref
there.
Also, since commit 1e88eb1b2c ("drm/amd/display: Drop
CONFIG_DRM_AMD_DC_HDCP") there are two separate checks for NULL in
'adev->dm.dc' before dc_deinit_callbacks() and dc_dmub_srv_destroy().
Clean up by combining them all under one 'if'.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
Fixes: 81927e2808 ("drm/amd/display: Support for DMUB AUX")
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4891d979c ]
Clean up a typo in pr_err() erroneously printing NI MC 'rdev->mc_fw->size'
during SMC firmware load. Log 'rdev->smc_fw->size' instead.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
Fixes: 6596afd48a ("drm/radeon/kms: add dpm support for btc (v3)")
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ccb49011bb ]
Dquots pointed to from i_dquot arrays in inodes are protected by
dquot_srcu. Annotate them as such and change .get_dquots callback to
return properly annotated pointer to make sparse happy.
Fixes: b9ba6f94b2 ("quota: remove dqptr_sem")
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 179b8c97eb ]
Dquot pointers in i_dquot array in the inode are protected by
dquot_srcu. Annotate the array pointers with __rcu, perform the locked
dereferences with srcu_dereference_check() instead of plain reads, and
set the array elements with rcu_assign_pointer().
Fixes: b9ba6f94b2 ("quota: remove dqptr_sem")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202402061900.rTuYDlo6-lkp@intel.com/
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d0aa72604f ]
Below race may cause NULL pointer dereference
P1 P2
dquot_free_inode quota_off
drop_dquot_ref
remove_dquot_ref
dquots = i_dquot(inode)
dquots = i_dquot(inode)
srcu_read_lock
dquots[cnt]) != NULL (1)
dquots[type] = NULL (2)
spin_lock(&dquots[cnt]->dq_dqb_lock) (3)
....
If dquot_free_inode(or other routines) checks inode's quota pointers (1)
before quota_off sets it to NULL(2) and use it (3) after that, NULL pointer
dereference will be triggered.
So let's fix it by using a temporary pointer to avoid this issue.
Signed-off-by: Wang Jianjian <wangjianjian3@huawei.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Message-Id: <20240202081852.2514092-1-wangjianjian3@huawei.com>
Stable-dep-of: 179b8c97eb ("quota: Fix rcu annotations of inode dquot pointers")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cdb637d339 ]
The issue arises when the array 'adev->vcn.vcn_config' is accessed
before checking if the index 'adev->vcn.num_vcn_inst' is within the
bounds of the array.
The fix involves moving the bounds check before the array access. This
ensures that 'adev->vcn.num_vcn_inst' is within the bounds of the array
before it is used as an index.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/amdgpu_discovery.c:1289 amdgpu_discovery_reg_base_init() error: testing array offset 'adev->vcn.num_vcn_inst' after use.
Fixes: a0ccc717c4 ("drm/amdgpu/discovery: validate VCN and SDMA instances")
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c64f4cdf4 ]
In dvb_register_device, *pdvbdev is set equal to dvbdev, which is freed
in several error-handling paths. However, *pdvbdev is not set to NULL
after dvbdev's deallocation, causing use-after-frees in many places,
for example, in the following call chain:
budget_register
|-> dvb_dmxdev_init
|-> dvb_register_device
|-> dvb_dmxdev_release
|-> dvb_unregister_device
|-> dvb_remove_device
|-> dvb_device_put
|-> kref_put
When calling dvb_unregister_device, dmxdev->dvbdev (i.e. *pdvbdev in
dvb_register_device) could point to memory that had been freed in
dvb_register_device. Thereafter, this pointer is transferred to
kref_put and triggering a use-after-free.
Link: https://lore.kernel.org/linux-media/20240203134046.3120099-1-alexious@zju.edu.cn
Fixes: b619010247 ("V4L/DVB (5244): Dvbdev: fix illegal re-usage of fileoperations struct")
Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4bd14b2fd8 ]
According to the datasheets, the ESMT chips in question will return a 5
byte long identification code where the last 3 bytes are the JEDEC
continuation codes (7Fh). Although, I would have expected 4 continuation
codes as Powerchip Semiconductor (C8h, corresponding to the parameter
page data) is located in bank 5 of the JEDEC database.
By matching the full 5 bytes we can avoid clashes with GigaDevice NAND
flashes.
This fix allows the MT7688-based GARDENA smart Gateway to boot again.
Fixes: aa08bf187f ("mtd: spinand: esmt: add support for F50D2G41KA")
Signed-off-by: Ezra Buehler <ezra.buehler@husqvarnagroup.com>
Reviewed-by: Martin Kurbanov <mmkurbanov@salutedevices.com>
Tested-by: Martin Kurbanov <mmkurbanov@salutedevices.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240125200108.24374-3-ezra@easyb.ch
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f94b49a5b ]
The entity->name (i.e. name) is allocated in v4l2_m2m_register_entity
but isn't freed in its following error-handling paths. This patch
adds such deallocation to prevent memleak of entity->name.
Fixes: be2fff6563 ("media: add helpers for memory-to-memory media controller")
Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8cf9c50510 ]
In tpg_alloc, resources should be deallocated in each and every
error-handling paths, since they are allocated in for statements.
Otherwise there would be memleaks because tpg_free is called only when
tpg_alloc return 0.
Fixes: 63881df94d ("[media] vivid: add the Test Pattern Generator")
Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd61d77a3d ]
Static analyzers generate alerts for an unchecked call to
`media_device_register()`. However, in this case, the device will work
reliably without the media controller API.
Add a comment above the call to prevent future unnecessary changes.
Suggested-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Fixes: 37ecc7b127 ("[media] em28xx: add media controller support")
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 67c15187d4 ]
When SPI transfer is being prepared, the spi-s3c64xx driver will call
clk_set_rate() to change the rate of SPI source clock (IPCLK). But IPCLK
is a gate (leaf) clock, so it must propagate the rate change up the
clock tree, so that corresponding DIV clocks can actually change their
divider values. Add CLK_SET_RATE_PARENT flag to corresponding clocks for
all SPI instances in Exynos850 (spi_0, spi_1 and spi_2) to make it
possible. This change involves next clocks:
usi_spi_0:
Clock Block Div range
--------------------------------------------
gout_spi0_ipclk CMU_PERI -
dout_peri_spi0 CMU_PERI /1..32
mout_peri_spi_user CMU_PERI -
dout_peri_ip CMU_TOP /1..16
usi_cmgp0:
Clock Block Div range
--------------------------------------------
gout_cmgp_usi0_ipclk CMU_CMGP -
dout_cmgp_usi0 CMU_CMGP /1..32
mout_cmgp_usi0 CMU_CMGP -
gout_clkcmu_cmgp_bus CMU_APM -
dout_apm_bus CMU_APM /1..8
usi_cmgp1:
Clock Block Div range
--------------------------------------------
gout_cmgp_usi1_ipclk CMU_CMGP -
dout_cmgp_usi1 CMU_CMGP /1..32
mout_cmgp_usi1 CMU_CMGP -
gout_clkcmu_cmgp_bus CMU_APM -
dout_apm_bus CMU_APM /1..8
With input clock of 400 MHz, this scheme provides next IPCLK rate range,
for each SPI block:
SPI0: 781 kHz ... 400 MHz
SPI1/2: 1.6 MHz ... 400 MHz
Accounting for internal /4 divider in SPI blocks, and because the max
SPI frequency is limited at 50 MHz, it gives us next SPI SCK rates:
SPI0: 200 kHz ... 49.9 MHz
SPI1/2: 400 kHz ... 49.9 MHz
Which should cover all possible applications of SPI bus. Of course,
setting SPI frequency to values as low as 500 kHz will also affect the
common bus dividers (dout_apm_bus or dout_peri_ip), which in turn
effectively lowers the rates for all leaf bus clocks derived from those
dividers, like HSI2C and I3C clocks. But at least it gives the board
designer a choice, whether to keep all clocks (SPI/HSI2C/I3C) at high
frequencies, or make all those clocks have lower frequencies. Not
propagating the rate change to those common dividers would limit this
choice to "only high frequencies are allowed for SPI/HSI2C/I3C" option,
making the common dividers useless. This decision follows the "Worse is
better" approach, relying on the users/engineers to know the system
internals when working with such low-level features, instead of trying
to account for all possible use-cases.
Fixes: 7dd0557819 ("clk: samsung: Introduce Exynos850 clock driver")
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20240125013858.3986-2-semen.protsenko@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ccfe80d02 ]
The 'stream' pointer is used in dcn10_set_output_transfer_func() before
the check if 'stream' is NULL.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/../display/dc/hwss/dcn10/dcn10_hwseq.c:1892 dcn10_set_output_transfer_func() warn: variable dereferenced before check 'stream' (see line 1875)
Fixes: ddef02de0d ("drm/amd/display: add null checks before logging")
Cc: Wyatt Wood <wyatt.wood@amd.com>
Cc: Anthony Koo <Anthony.Koo@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24852ef2e2 ]
The msr PMU is a software one, meaning msr events may be grouped
with events in a hardware context. As the msr PMU isn't marked as a
software PMU by perf_pmu__is_software, groups with the msr PMU in
are broken and the msr events placed in a different group. This
may lead to multiplexing errors where a hardware event isn't
counted while the msr event, such as tsc, is. Fix all of this by
marking the msr PMU as software, which agrees with the driver.
Before:
```
$ perf stat -e '{slots,tsc}' -a true
WARNING: events were regrouped to match PMUs
Performance counter stats for 'system wide':
1,750,335 slots
4,243,557 tsc
0.001456717 seconds time elapsed
```
After:
```
$ perf stat -e '{slots,tsc}' -a true
Performance counter stats for 'system wide':
12,526,380 slots
3,415,163 tsc
0.001488360 seconds time elapsed
```
Fixes: 251aa04024 ("perf parse-events: Wildcard most "numeric" events")
Signed-off-by: Ian Rogers <irogers@google.com>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Cc: James Clark <james.clark@arm.com>
Cc: Caleb Biggers <caleb.biggers@intel.com>
Cc: Edward Baker <edward.baker@intel.com>
Cc: Perry Taylor <perry.taylor@intel.com>
Cc: Samantha Alt <samantha.alt@intel.com>
Cc: Weilin Wang <weilin.wang@intel.com>
Link: https://lore.kernel.org/r/20240124234200.1510417-1-irogers@google.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2814646f76 ]
Previous attempt to autodetect well-behaving patched firmware
introduced in commit 46a0a2c96f ("HID: lenovo: Detect quirk-free fw
on cptkbd and stop applying workaround") has shown that there are
false-positives on original firmware (on both 1st gen and 2nd gen
keyboards) which causes the middle button click workaround to be
mistakenly disabled.
This commit adds explicit parameter to sysfs to control this
workaround.
Fixes: 46a0a2c96f ("HID: lenovo: Detect quirk-free fw on cptkbd and stop applying workaround")
Fixes: 43527a0094 ("HID: lenovo: Restrict detection of patched firmware only to USB cptkbd")
Signed-off-by: Mikhail Khvainitski <me@khvoinitsky.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 02f9b50e04 ]
In pipe mode, no need to switch perf data output, therefore,
'--timestamp-filename' option should not take effect.
Check the conflict before recording and output WARNING.
In this case, the check pipe mode in perf_data__switch() can be removed.
Before:
# perf record --timestamp-filename -o- perf test -w noploop | perf report -i- --percent-limit=1
# To display the perf.data header info, please use --header/--header-only options.
#
[ perf record: Woken up 1 times to write data ]
[ perf record: Dump -.2024011812110182 ]
#
# Total Lost Samples: 0
#
# Samples: 4K of event 'cycles:P'
# Event count (approx.): 2176784359
#
# Overhead Command Shared Object Symbol
# ........ ....... .................... ......................................
#
97.83% perf perf [.] noploop
#
# (Tip: Print event counts in CSV format with: perf stat -x,)
#
After:
# perf record --timestamp-filename -o- perf test -w noploop | perf report -i- --percent-limit=1
WARNING: --timestamp-filename option is not available in pipe mode.
# To display the perf.data header info, please use --header/--header-only options.
#
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.000 MB - ]
#
# Total Lost Samples: 0
#
# Samples: 4K of event 'cycles:P'
# Event count (approx.): 2185575421
#
# Overhead Command Shared Object Symbol
# ........ ....... ..................... .............................................
#
97.75% perf perf [.] noploop
#
# (Tip: Profiling branch (mis)predictions with: perf record -b / perf report)
#
Fixes: ecfd7a9c04 ("perf record: Add '--timestamp-filename' option to append timestamp to output file name")
Signed-off-by: Yang Jihong <yangjihong1@huawei.com>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Link: https://lore.kernel.org/r/20240119040304.3708522-3-yangjihong1@huawei.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a61f89bf76 ]
It's hard to distinguish the default cycles events among hybrid PMUs.
For example,
$ perf top
Available samples
385 cycles:P
903 cycles:P
The other tool, e.g., perf record, uniforms the event name and adds the
hybrid PMU name before opening the event. So the events can be easily
distinguished. Apply the same methodology for the perf top as well.
The evlist__uniquify_name() will be invoked by both record and top.
Move it to util/evlist.c
With the patch:
$ perf top
Available samples
148 cpu_atom/cycles:P/
1K cpu_core/cycles:P/
Reviewed-by: Ian Rogers <irogers@google.com>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Hector Martin <marcan@marcan.st>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: https://lore.kernel.org/r/20231214144612.1092028-2-kan.liang@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Stable-dep-of: 02f9b50e04 ("perf record: Check conflict between '--timestamp-filename' option and pipe mode before recording")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6568d82512 ]
The TLP Prefix Log Register consists of multiple DWORDs (PCIe r6.1 sec
7.9.14.13) but the loop in dpc_process_rp_pio_error() keeps reading from
the first DWORD, so we print only the first PIO TLP Prefix (duplicated
several times), and we never print the second, third, etc., Prefixes.
Add the iteration count based offset calculation into the config read.
Fixes: f20c4ea49e ("PCI/DPC: Add eDPC support")
Link: https://lore.kernel.org/r/20240118110815.3867-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
[bhelgaas: add user-visible details to commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 448699c522 ]
Since commit 1029939b37 ("media: v4l: async: Simplify async sub-device fwnode matching"),
async connections are matched using the async sub-device fwnode, not that
of the endpoint. Fix this by using the fwnode of the connection match to
find the pad.
Fixes: 1029939b37 ("media: v4l: async: Simplify async sub-device fwnode matching")
Signed-off-by: Julien Massot <julien.massot@collabora.com>
Reviewed-by: Jai Luthra <j-luthra@ti.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65e8fbde64 ]
There is this reported crash when experimenting with the lvm2 testsuite.
The list corruption is caused by the fact that the postsuspend and resume
methods were not paired correctly; there were two consecutive calls to the
origin_postsuspend function. The second call attempts to remove the
"hash_list" entry from a list, while it was already removed by the first
call.
Fix __dm_internal_resume so that it calls the preresume and resume
methods of the table's targets.
If a preresume method of some target fails, we are in a tricky situation.
We can't return an error because dm_internal_resume isn't supposed to
return errors. We can't return success, because then the "resume" and
"postsuspend" methods would not be paired correctly. So, we set the
DMF_SUSPENDED flag and we fake normal suspend - it may confuse userspace
tools, but it won't cause a kernel crash.
------------[ cut here ]------------
kernel BUG at lib/list_debug.c:56!
invalid opcode: 0000 [#1] PREEMPT SMP
CPU: 1 PID: 8343 Comm: dmsetup Not tainted 6.8.0-rc6 #4
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-2 04/01/2014
RIP: 0010:__list_del_entry_valid_or_report+0x77/0xc0
<snip>
RSP: 0018:ffff8881b831bcc0 EFLAGS: 00010282
RAX: 000000000000004e RBX: ffff888143b6eb80 RCX: 0000000000000000
RDX: 0000000000000001 RSI: ffffffff819053d0 RDI: 00000000ffffffff
RBP: ffff8881b83a3400 R08: 00000000fffeffff R09: 0000000000000058
R10: 0000000000000000 R11: ffffffff81a24080 R12: 0000000000000001
R13: ffff88814538e000 R14: ffff888143bc6dc0 R15: ffffffffa02e4bb0
FS: 00000000f7c0f780(0000) GS:ffff8893f0a40000(0000) knlGS:0000000000000000
CS: 0010 DS: 002b ES: 002b CR0: 0000000080050033
CR2: 0000000057fb5000 CR3: 0000000143474000 CR4: 00000000000006b0
Call Trace:
<TASK>
? die+0x2d/0x80
? do_trap+0xeb/0xf0
? __list_del_entry_valid_or_report+0x77/0xc0
? do_error_trap+0x60/0x80
? __list_del_entry_valid_or_report+0x77/0xc0
? exc_invalid_op+0x49/0x60
? __list_del_entry_valid_or_report+0x77/0xc0
? asm_exc_invalid_op+0x16/0x20
? table_deps+0x1b0/0x1b0 [dm_mod]
? __list_del_entry_valid_or_report+0x77/0xc0
origin_postsuspend+0x1a/0x50 [dm_snapshot]
dm_table_postsuspend_targets+0x34/0x50 [dm_mod]
dm_suspend+0xd8/0xf0 [dm_mod]
dev_suspend+0x1f2/0x2f0 [dm_mod]
? table_deps+0x1b0/0x1b0 [dm_mod]
ctl_ioctl+0x300/0x5f0 [dm_mod]
dm_compat_ctl_ioctl+0x7/0x10 [dm_mod]
__x64_compat_sys_ioctl+0x104/0x170
do_syscall_64+0x184/0x1b0
entry_SYSCALL_64_after_hwframe+0x46/0x4e
RIP: 0033:0xf7e6aead
<snip>
---[ end trace 0000000000000000 ]---
Fixes: ffcc393641 ("dm: enhance internal suspend and resume interface")
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b25b8f4b8e ]
An empty flush doesn't have a payload, so it should never be looked at
when considering to possibly requeue a bio for the case when a reshape
is in progress.
Fixes: 9dbd1aa3a8 ("dm raid: add reshaping support to the target")
Reported-by: Patrick Plenefisch <simonpatp@gmail.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84e95149bd ]
The kmalloc_array() in nfp_fl_lag_do_work() will return null, if
the physical memory has run out. As a result, if we dereference
the acti_netdevs, the null pointer dereference bugs will happen.
This patch adds a check to judge whether allocation failure occurs.
If it happens, the delayed work will be rescheduled and try again.
Fixes: bb9a8d0311 ("nfp: flower: monitor and offload LAG groups")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Link: https://lore.kernel.org/r/20240308142540.9674-1-duoming@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d6eb8de201 ]
The 'len' variable can't be negative when assigned the result of
'min_t' because all 'min_t' parameters are cast to unsigned int,
and then the minimum one is chosen.
To fix the logic, check 'len' as read from 'optlen',
where the types of relevant variables are (signed) int.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ed5f41513 ]
The 'len' variable can't be negative when assigned the result of
'min_t' because all 'min_t' parameters are cast to unsigned int,
and then the minimum one is chosen.
To fix the logic, check 'len' as read from 'optlen',
where the types of relevant variables are (signed) int.
Fixes: ab7ac4eb98 ("kcm: Kernel Connection Multiplexor module")
Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4bb3ba7b74 ]
The 'len' variable can't be negative when assigned the result of
'min_t' because all 'min_t' parameters are cast to unsigned int,
and then the minimum one is chosen.
To fix the logic, check 'len' as read from 'optlen',
where the types of relevant variables are (signed) int.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 955e9876ba ]
The 'len' variable can't be negative when assigned the result of
'min_t' because all 'min_t' parameters are cast to unsigned int,
and then the minimum one is chosen.
To fix the logic, check 'len' as read from 'optlen',
where the types of relevant variables are (signed) int.
Fixes: 3557baabf2 ("[L2TP]: PPP over L2TP driver core")
Reviewed-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c3be3e0eb ]
The 'olr' variable can't be negative when assigned the result of
'min_t' because all 'min_t' parameters are cast to unsigned int,
and then the minimum one is chosen.
To fix the logic, check 'olr' as read from 'optlen',
where the types of relevant variables are (signed) int.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 716edc9706 ]
The 'len' variable can't be negative when assigned the result of
'min_t' because all 'min_t' parameters are cast to unsigned int,
and then the minimum one is chosen.
To fix the logic, check 'len' as read from 'optlen',
where the types of relevant variables are (signed) int.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru>
Reviewed-by: Jason Xing <kerneljasonxing@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28330ceb95 ]
If the kernel isn't built with interconnect support, icc_get_name()
returns NULL and we get following warning:
drivers/opp/debugfs.c: In function 'bw_name_read':
drivers/opp/debugfs.c:43:42: error: '%.62s' directive argument is null [-Werror=format-overflow=]
i = scnprintf(buf, sizeof(buf), "%.62s\n", icc_get_name(path));
Fix it.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202402141313.81ltVF5g-lkp@intel.com/
Fixes: 0430b1d570 ("opp: Expose bandwidth information via debugfs")
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f28be64d1 ]
Lockdep reported the following issue when mounting erofs with a domain_id:
============================================
WARNING: possible recursive locking detected
6.8.0-rc7-xfstests #521 Not tainted
--------------------------------------------
mount/396 is trying to acquire lock:
ffff907a8aaaa0e0 (&type->s_umount_key#50/1){+.+.}-{3:3},
at: alloc_super+0xe3/0x3d0
but task is already holding lock:
ffff907a8aaa90e0 (&type->s_umount_key#50/1){+.+.}-{3:3},
at: alloc_super+0xe3/0x3d0
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&type->s_umount_key#50/1);
lock(&type->s_umount_key#50/1);
*** DEADLOCK ***
May be due to missing lock nesting notation
2 locks held by mount/396:
#0: ffff907a8aaa90e0 (&type->s_umount_key#50/1){+.+.}-{3:3},
at: alloc_super+0xe3/0x3d0
#1: ffffffffc00e6f28 (erofs_domain_list_lock){+.+.}-{3:3},
at: erofs_fscache_register_fs+0x3d/0x270 [erofs]
stack backtrace:
CPU: 1 PID: 396 Comm: mount Not tainted 6.8.0-rc7-xfstests #521
Call Trace:
<TASK>
dump_stack_lvl+0x64/0xb0
validate_chain+0x5c4/0xa00
__lock_acquire+0x6a9/0xd50
lock_acquire+0xcd/0x2b0
down_write_nested+0x45/0xd0
alloc_super+0xe3/0x3d0
sget_fc+0x62/0x2f0
vfs_get_super+0x21/0x90
vfs_get_tree+0x2c/0xf0
fc_mount+0x12/0x40
vfs_kern_mount.part.0+0x75/0x90
kern_mount+0x24/0x40
erofs_fscache_register_fs+0x1ef/0x270 [erofs]
erofs_fc_fill_super+0x213/0x380 [erofs]
This is because the file_system_type of both erofs and the pseudo-mount
point of domain_id is erofs_fs_type, so two successive calls to
alloc_super() are considered to be using the same lock and trigger the
warning above.
Therefore add a nodev file_system_type called erofs_anon_fs_type in
fscache.c to silence this complaint. Because kern_mount() takes a
pointer to struct file_system_type, not its (string) name. So we don't
need to call register_filesystem(). In addition, call init_pseudo() in
erofs_anon_init_fs_context() as suggested by Al Viro, so that we can
remove erofs_fc_fill_pseudo_super(), erofs_fc_anon_get_tree(), and
erofs_anon_context_ops.
Suggested-by: Al Viro <viro@zeniv.linux.org.uk>
Fixes: a9849560c5 ("erofs: introduce a pseudo mnt to manage shared cookies")
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-and-tested-by: Jingbo Xu <jefflexu@linux.alibaba.com>
Reviewed-by: Yang Erkun <yangerkun@huawei.com>
Link: https://lore.kernel.org/r/20240307101018.2021925-1-libaokun1@huawei.com
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c88c16dc2 ]
if you have a variable that holds NULL or a pointer to live struct mount,
do not shove ERR_PTR() into it - not if you later treat "not NULL" as
"holds a pointer to object".
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Stable-dep-of: 0f28be64d1 ("erofs: fix lockdep false positives on initializing erofs_pseudo_mnt")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e719b4d156 ]
Create struct bdev_handle that contains all parameters that need to be
passed to blkdev_put() and provide bdev_open_* functions that return
this structure instead of plain bdev pointer. This will eventually allow
us to pass one more argument to blkdev_put() (renamed to bdev_release())
without too much hassle.
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20230927093442.25915-1-jack@suse.cz
Signed-off-by: Christian Brauner <brauner@kernel.org>
Stable-dep-of: 0f28be64d1 ("erofs: fix lockdep false positives on initializing erofs_pseudo_mnt")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ab3e8d67f ]
According to Section 1.2 of Core Specification Supplement Part A the
complete or short name strings are defined as utf8s, which should not
include the trailing NULL for variable length array as defined in Core
Specification Vol1 Part E Section 2.9.3.
Removing the trailing NULL allows PTS to retrieve the random address based
on device name, e.g. for SM/PER/KDU/BV-02-C, SM/PER/KDU/BV-08-C or
GAP/BROB/BCST/BV-03-C.
Fixes: f61851f64b ("Bluetooth: Fix append max 11 bytes of name to scan rsp data")
Signed-off-by: Frédéric Danis <frederic.danis@collabora.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11d80f79dd ]
Currently, the mac port is fixed to configured as full dplex mode in
hclge_mac_init() when driver initialization or reset restore. Users may
change the mode to half duplex with ethtool, so it may cause the user
configuration dropped after reset.
To fix it, don't change the duplex mode when resetting.
Fixes: 2d03eacc0b ("net: hns3: Only update mac configuation when necessary")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 07a1d6dc90 ]
In hns3_dcbnl_ieee_delapp, should check ieee_delapp not ieee_setapp.
This path fix the wrong judgment.
Fixes: 0ba22bcb22 ("net: hns3: add support config dscp map to tc")
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4469c0c5b1 ]
The phy_get_internal_delay function could try to access to an empty
array in the case that the driver is calling phy_get_internal_delay
without defining delay_values and rx-internal-delay-ps or
tx-internal-delay-ps is defined to 0 in the device-tree.
This will lead to "unable to handle kernel NULL pointer dereference at
virtual address 0". To avoid this kernel oops, the test should be delay
>= 0. As there is already delay < 0 test just before, the test could
only be size == 0.
Fixes: 92252eec91 ("net: phy: Add a helper to return the index for of the internal delay")
Co-developed-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Signed-off-by: Kévin L'hôpital <kevin.lhopital@savoirfairelinux.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4386ab4f6 ]
When rule policy is changed, ipv6 socket cache is not refreshed.
The sock's skb still uses a outdated route cache and was sent to
a wrong interface.
To avoid this error we should update fib node's version when
rule is changed. Then skb's route will be reroute checked as
route cache version is already different with fib node version.
The route cache is refreshed to match the latest rule.
Fixes: 101367c2f8 ("[IPV6]: Policy Routing Rules")
Signed-off-by: Shiming Cheng <shiming.cheng@mediatek.com>
Signed-off-by: Lena Wang <lena.wang@mediatek.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a4b21250b ]
The stackmap code relies on roundup_pow_of_two() to compute the number
of hash buckets, and contains an overflow check by checking if the
resulting value is 0. However, on 32-bit arches, the roundup code itself
can overflow by doing a 32-bit left-shift of an unsigned long value,
which is undefined behaviour, so it is not guaranteed to truncate
neatly. This was triggered by syzbot on the DEVMAP_HASH type, which
contains the same check, copied from the hashtab code.
The commit in the fixes tag actually attempted to fix this, but the fix
did not account for the UB, so the fix only works on CPUs where an
overflow does result in a neat truncation to zero, which is not
guaranteed. Checking the value before rounding does not have this
problem.
Fixes: 6183f4d3a0 ("bpf: Check for integer overflow when using roundup_pow_of_two()")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Reviewed-by: Bui Quang Minh <minhquangbui99@gmail.com>
Message-ID: <20240307120340.99577-4-toke@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6787d916c2 ]
The hashtab code relies on roundup_pow_of_two() to compute the number of
hash buckets, and contains an overflow check by checking if the
resulting value is 0. However, on 32-bit arches, the roundup code itself
can overflow by doing a 32-bit left-shift of an unsigned long value,
which is undefined behaviour, so it is not guaranteed to truncate
neatly. This was triggered by syzbot on the DEVMAP_HASH type, which
contains the same check, copied from the hashtab code. So apply the same
fix to hashtab, by moving the overflow check to before the roundup.
Fixes: daaf427c6a ("bpf: fix arraymap NULL deref and missing overflow and zero size checks")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Message-ID: <20240307120340.99577-3-toke@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 281d464a34 ]
The devmap code allocates a number hash buckets equal to the next power
of two of the max_entries value provided when creating the map. When
rounding up to the next power of two, the 32-bit variable storing the
number of buckets can overflow, and the code checks for overflow by
checking if the truncated 32-bit value is equal to 0. However, on 32-bit
arches the rounding up itself can overflow mid-way through, because it
ends up doing a left-shift of 32 bits on an unsigned long value. If the
size of an unsigned long is four bytes, this is undefined behaviour, so
there is no guarantee that we'll end up with a nice and tidy 0-value at
the end.
Syzbot managed to turn this into a crash on arm32 by creating a
DEVMAP_HASH with max_entries > 0x80000000 and then trying to update it.
Fix this by moving the overflow check to before the rounding up
operation.
Fixes: 6f9d451ab1 ("xdp: Add devmap_hash map type for looking up devices by hashed index")
Link: https://lore.kernel.org/r/000000000000ed666a0611af6818@google.com
Reported-and-tested-by: syzbot+8cd36f6b65f3cafd400a@syzkaller.appspotmail.com
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Message-ID: <20240307120340.99577-2-toke@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb0cd4ee11 ]
With commit 36bbc5b4ff ("cacheinfo: Allow early detection and population
of cache attributes") the shared cpu list for each cache level higher than
L1 is rebuilt even if the list already has been set up.
This is caused by the removal of the cpumask_empty() check within
cache_shared_cpu_map_setup().
However architectures can enforce that the shared cpu list is not rebuilt
by simply setting cpu_map_populated of the per cpu cache info structure to
true, which is also the fix for this problem.
Before:
$ cat /sys/devices/system/cpu/cpu1/cache/index2/shared_cpu_list
0-7
After:
$ cat /sys/devices/system/cpu/cpu1/cache/index2/shared_cpu_list
1
Fixes: 36bbc5b4ff ("cacheinfo: Allow early detection and population of cache attributes")
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 947ec0d002 ]
hci_send_cmd_sync first sends skb and then tries to clone it. However,
the driver may have already freed the skb at that point.
Fix by cloning the sent_cmd cloned just above, instead of the original.
Log:
================================================================
BUG: KASAN: slab-use-after-free in __copy_skb_header+0x1a/0x240
...
Call Trace: ..
__skb_clone+0x59/0x2c0
hci_cmd_work+0x3b3/0x3d0 [bluetooth]
process_one_work+0x459/0x900
...
Allocated by task 129: ...
__alloc_skb+0x1ae/0x220
__hci_cmd_sync_sk+0x44c/0x7a0 [bluetooth]
__hci_cmd_sync_status+0x24/0xb0 [bluetooth]
set_cig_params_sync+0x778/0x7d0 [bluetooth]
...
Freed by task 0: ...
kmem_cache_free+0x157/0x3c0
__usb_hcd_giveback_urb+0x11e/0x1e0
usb_giveback_urb_bh+0x1ad/0x2a0
tasklet_action_common.isra.0+0x259/0x4a0
__do_softirq+0x15b/0x5a7
================================================================
Fixes: 2615fd9a7c ("Bluetooth: hci_sync: Fix overwriting request callback")
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f7b94bdc1e ]
Attemting to do sock_lock on .recvmsg may cause a deadlock as shown
bellow, so instead of using sock_sock this uses sk_receive_queue.lock
on bt_sock_ioctl to avoid the UAF:
INFO: task kworker/u9:1:121 blocked for more than 30 seconds.
Not tainted 6.7.6-lemon #183
Workqueue: hci0 hci_rx_work
Call Trace:
<TASK>
__schedule+0x37d/0xa00
schedule+0x32/0xe0
__lock_sock+0x68/0xa0
? __pfx_autoremove_wake_function+0x10/0x10
lock_sock_nested+0x43/0x50
l2cap_sock_recv_cb+0x21/0xa0
l2cap_recv_frame+0x55b/0x30a0
? psi_task_switch+0xeb/0x270
? finish_task_switch.isra.0+0x93/0x2a0
hci_rx_work+0x33a/0x3f0
process_one_work+0x13a/0x2f0
worker_thread+0x2f0/0x410
? __pfx_worker_thread+0x10/0x10
kthread+0xe0/0x110
? __pfx_kthread+0x10/0x10
ret_from_fork+0x2c/0x50
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1b/0x30
</TASK>
Fixes: 2e07e8348e ("Bluetooth: af_bluetooth: Fix Use-After-Free in bt_sock_recvmsg")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79f4127a50 ]
This checks if CONFIG_DEV_COREDUMP is enabled before attempting to clone
the skb and also make sure btmtk_process_coredump frees the skb passed
following the same logic.
Fixes: 0b70151328 ("Bluetooth: btusb: mediatek: add MediaTek devcoredump support")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 41c56aa94c ]
The __hci_cmd_sync() function doesn't return NULL. Checking for NULL
doesn't make the code safer, it just confuses people.
When a function returns both error pointers and NULL then generally the
NULL is a kind of success case. For example, maybe we look up an item
then errors mean we ran out of memory but NULL means the item is not
found. Or if we request a feature, then error pointers mean that there
was an error but NULL means that the feature has been deliberately
turned off.
In this code it's different. The NULL is handled as if there is a bug
in __hci_cmd_sync() where it accidentally returns NULL instead of a
proper error code. This was done consistently until commit 9e14606d8f
("Bluetooth: msft: Extended monitor tracking by address filter") which
deleted the work around for the potential future bug and treated NULL as
success.
Predicting potential future bugs is complicated, but we should just fix
them instead of working around them. Instead of debating whether NULL
is failure or success, let's just say it's currently impossible and
delete the dead code.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Stable-dep-of: a6e06258f4 ("Bluetooth: msft: Fix memory leak")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 81137162bf ]
struct hci_dev_info has a fixed size name[8] field so in the event that
hdev->name is bigger than that strcpy would attempt to write past its
size, so this fixes this problem by switching to use strscpy.
Fixes: dcda165706 ("Bluetooth: hci_core: Fix build warnings")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a6d793e9c ]
In some cases uart-base drivers may need to use priv data. For
example, to store information needed for devcoredump.
Fixes: 044014ce85 ("Bluetooth: btrtl: Add Realtek devcoredump support")
Signed-off-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2615fd9a7c ]
In a few cases the stack may generate commands as responses to events
which would happen to overwrite the sent_cmd, so this attempts to store
the request in req_skb so even if sent_cmd is replaced with a new
command the pending request will remain in stored in req_skb.
Fixes: 6a98e3836f ("Bluetooth: Add helper for serialized HCI command execution")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63298d6e75 ]
If command has timed out call __hci_cmd_sync_cancel to notify the
hci_req since it will inevitably cause a timeout.
This also rework the code around __hci_cmd_sync_cancel since it was
wrongly assuming it needs to cancel timer as well, but sometimes the
timers have not been started or in fact they already had timed out in
which case they don't need to be cancel yet again.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Stable-dep-of: 2615fd9a7c ("Bluetooth: hci_sync: Fix overwriting request callback")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 56d074d26c ]
The optional variants for the gpiod_get() family of functions return NULL
if the GPIO in question is not associated with this device. They return
ERR_PTR() on any other error. NULL descriptors are graciously handled by
GPIOLIB and can be safely passed to any of the GPIO consumer interfaces
as they will return 0 and act as if the function succeeded. If one is
using the optional variant, then there's no point in checking for NULL.
Fixes: 6845667146 ("Bluetooth: hci_qca: Fix NULL vs IS_ERR_OR_NULL check in qca_serdev_probe")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eeda1bf97b ]
BIG Sync (aka. Broadcast sink) requires to inform that the device is
connected when a data path is active otherwise userspace could attempt
to free resources allocated to the device object while scanning.
Fixes: 1d11d70d1f ("Bluetooth: ISO: Pass BIG encryption info through QoS")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78e3639fc8 ]
The "pending connections" feature was originally introduced with commit
4c67bc74f0 ("[Bluetooth] Support concurrent connect requests") and
6bd5741612 ("[Bluetooth] Handling pending connect attempts after
inquiry") to handle controllers supporting only a single connection request
at a time. Later things were extended to also cancel ongoing inquiries on
connect() with commit 89e65975fe ("Bluetooth: Cancel Inquiry before
Create Connection").
With commit a9de924806 ("[Bluetooth] Switch from OGF+OCF to using only
opcodes"), hci_conn_check_pending() was introduced as a helper to
consolidate a few places where we check for pending connections (indicated
by the BT_CONNECT2 flag) and then try to connect.
This refactoring commit also snuck in two more calls to
hci_conn_check_pending():
- One is in the failure callback of hci_cs_inquiry(), this one probably
makes sense: If we send an "HCI Inquiry" command and then immediately
after a "Create Connection" command, the "Create Connection" command might
fail before the "HCI Inquiry" command, and then we want to retry the
"Create Connection" on failure of the "HCI Inquiry".
- The other added call to hci_conn_check_pending() is in the event handler
for the "Remote Name" event, this seems unrelated and is possibly a
copy-paste error, so remove that one.
Fixes: a9de924806 ("[Bluetooth] Switch from OGF+OCF to using only opcodes")
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fee054b757 ]
Queuing of power_off work was introduced in these functions with commits
8b064a3ad3 ("Bluetooth: Clean up HCI state when doing power off") and
c9910d0fb4 ("Bluetooth: Fix disconnecting connections in non-connected
states") in an effort to clean up state and do things like disconnecting
devices before actually powering off the device.
After that, commit a3172b7eb4 ("Bluetooth: Add timer to force power off")
introduced a timeout to ensure that the device actually got powered off,
even if some of the cleanup work would never complete.
This code later got refactored with commit cf75ad8b41 ("Bluetooth:
hci_sync: Convert MGMT_SET_POWERED"), which made powering off the device
synchronous and removed the need for initiating the power_off work from
other places. The timeout mentioned above got removed too, because we now
also made use of the command timeout during power on/off.
These days the power_off work still exists, but it only seems to only be
used for HCI_AUTO_OFF functionality, which is why we never noticed
those two leftover places where we queue power_off work. So let's remove
that code.
Fixes: cf75ad8b41 ("Bluetooth: hci_sync: Convert MGMT_SET_POWERED")
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 968667f2e0 ]
With commit cf75ad8b41 ("Bluetooth: hci_sync: Convert MGMT_SET_POWERED"),
the power off sequence got refactored so that this timeout was no longer
necessary, let's remove the leftover define from the header too.
Fixes: cf75ad8b41 ("Bluetooth: hci_sync: Convert MGMT_SET_POWERED")
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee14cc9ea1 ]
Fix "double" clearing of interrupts, which can cause external events
or timestamps to be missed.
The E1000_TSIRC Time Sync Interrupt Cause register can be cleared in two
ways, by either reading it or by writing '1' into the specific cause
bit. This is documented in section 8.16.1.
The following flow was used:
1. read E1000_TSIRC into 'tsicr';
2. handle the interrupts present into 'tsirc' and mark them in 'ack';
3. write 'ack' into E1000_TSICR;
As both (1) and (3) will clear the interrupt cause, if the same
interrupt happens again between (1) and (3) it will be ignored,
causing events to be missed.
Remove the extra clear in (3).
Fixes: 00c65578b4 ("igb: enable internal PPS for the i210")
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 244ae992e3 ]
Fix "double" clearing of interrupts, which can cause external events
or timestamps to be missed.
The IGC_TSIRC Time Sync Interrupt Cause register can be cleared in two
ways, by either reading it or by writing '1' into the specific cause
bit. This is documented in section 8.16.1.
The following flow was used:
1. read IGC_TSIRC into 'tsicr';
2. handle the interrupts present in 'tsirc' and mark them in 'ack';
3. write 'ack' into IGC_TSICR;
As both (1) and (3) will clear the interrupt cause, if the same
interrupt happens again between (1) and (3) it will be ignored,
causing events to be missed.
Remove the extra clear in (3).
Fixes: 2c344ae245 ("igc: Add support for TX timestamping")
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Kurt Kanzenbach <kurt@linutronix.de> # Intel i225
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1dfa21427 ]
Tenda U9 V2.0, which contains RTL8811CU, is practically unusable because
of frequent disconnections:
Feb 23 14:46:45 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-BEACON-LOSS
Feb 23 14:46:46 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-DISCONNECTED
bssid=90:55:de:__:__:__ reason=4 locally_generated=1
Feb 23 14:46:52 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-CONNECTED
- Connection to 90:55:de:__:__:__ completed [id=0 id_str=]
Feb 23 14:46:54 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-BEACON-LOSS
Feb 23 14:46:55 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-DISCONNECTED
bssid=90:55:de:__:__:__ reason=4 locally_generated=1
Feb 23 14:47:01 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-CONNECTED
- Connection to 90:55:de:__:__:__ completed [id=0 id_str=]
Feb 23 14:47:04 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-BEACON-LOSS
Feb 23 14:47:05 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-DISCONNECTED
bssid=90:55:de:__:__:__ reason=4 locally_generated=1
This is caused by a mistake in the chip initialisation. This version of
the chip requires loading an extra AGC table right after the main one,
but the extra table is being loaded at the wrong time, in
rtw_chip_board_info_setup().
Move the extra AGC table loading to the right place, in
rtw_phy_load_tables().
The rtw_chip_board_info_setup() can only do "software" things, and
rtw_phy_load_tables() can really do IO.
Fixes: 5d6651fe85 ("rtw88: 8821c: support RFE type2 wifi NIC")
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/276c31d8-b9a8-4e54-a3ac-09b74657aff7@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 41a7acb7dd ]
RTL8822CU, RTL8822BU, and RTL8821CU need an extra register write after
reading and writing certain addresses.
Without this, the firmware upload fails approximately more than 50% of
the time.
Tested with RTL8811CU (Tenda U9 V2.0) which is the same as RTL8821CU
but without Bluetooth.
Fixes: a82dfd33d1 ("wifi: rtw88: Add common USB chip support")
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/f12ed39d-28e8-4b8b-8d22-447bcf295afc@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a51ab63b29 ]
As there are some AMD processors which only support CPPC V2 firmware and
BIOS implementation, the amd_pstate driver will be failed to load when
system booting with below kernel warning message:
[ 0.477523] amd_pstate: the _CPC object is not present in SBIOS or ACPI disabled
To make the amd_pstate driver can be loaded on those TR40 processors, it
needs to match x86_model from 0x30 to 0x7F for family 17H.
With the change, the system can load amd_pstate driver as expected.
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reported-by: Gino Badouri <badouri.g@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218171
Fixes: fbd74d1689 ("ACPI: CPPC: Fix enabling CPPC on AMD systems with shared memory")
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3cfcfc102a ]
The creds and oa->data need to be freed in the error-handling paths after
their allocation. So this patch add these deallocations in the
corresponding paths.
Fixes: 1d658336b0 ("SUNRPC: Add RPC based upcall mechanism for RPCGSS auth")
Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e67b652d8e ]
The ctx->mech_used.data allocated by kmemdup is not freed in neither
gss_import_v2_context nor it only caller gss_krb5_import_sec_context,
which frees ctx on error.
Thus, this patch reform the last call of gss_import_v2_context to the
gss_krb5_import_ctx_v2, preventing the memleak while keepping the return
formation.
Fixes: 47d8480776 ("gss_krb5: handle new context format from gssd")
Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aaa8736370 ]
When building with CONFIG_XEN_PV=y, .text symbols are emitted into
the .notes section so that Xen can find the "startup_xen" entry point.
This information is used prior to booting the kernel, so relocations
are not useful. In fact, performing relocations against the .notes
section means that the KASLR base is exposed since /sys/kernel/notes
is world-readable.
To avoid leaking the KASLR base without breaking unprivileged tools that
are expecting to read /sys/kernel/notes, skip performing relocations in
the .notes section. The values readable in .notes are then identical to
those found in System.map.
Reported-by: Guixiong Wei <guixiongwei@gmail.com>
Closes: https://lore.kernel.org/all/20240218073501.54555-1-guixiongwei@gmail.com/
Fixes: 5ead97c84f ("xen: Core Xen implementation")
Fixes: da1a679cde ("Add /sys/kernel/notes")
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0fc19ab75a ]
The dtbscheck reports a warning for a wrong reset-names property for
the i2s2 controller on rk356x socs.
The other controllers on the soc provide tx and rx directions and hence
two resets and separate clocks for each direction, while i2s2 only
provides one reset. This was so far named just "m" which isn't part of
the binding.
The clock-names the controller uses all end in "tx", so use the matching
"tx-m" reset-name for the i2s controller.
Fixes: 755f37010f ("arm64: dts: rockchip: RK356x: Add I2S2 device node")
Acked-by: Uwe Kleine-König <ukleinek@debian.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20240227173526.710056-2-heiko@sntech.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 793551c965 ]
It is generally invalid to fail a Device Check notification if the scan
handler has not been attached to the given device after a bus rescan,
because there may be valid reasons for the scan handler to refuse
attaching to the device (for example, the device is not ready).
For this reason, modify acpi_scan_device_check() to return 0 in that
case without printing a warning.
While at it, reduce the log level of the "already enumerated" message
in the same function, because it is only interesting when debugging
notification handling
Fixes: 443fc82022 ("ACPI / hotplug: Rework generic code to handle suprise removals")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e23ad54fef ]
The Lunnen Ground 15 and 16 needs IRQ overriding for the keyboard to
work.
Adding an entries for these laptops to the override_table makes the
internal keyboard functional.
Signed-off-by: Alexey I. Froloff <raorn@raorn.name>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Stable-dep-of: 021a67d096 ("ACPI: resource: Add MAIBENBEN X577 to irq1_edge_low_force_override")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d776cfd5e ]
This devm API takes a consumer device as an argument to setup the devm
action, but throws it away when calling further into gpiolib. This leads
to odd debug messages like this:
(NULL device *): using DT '/gpio-keys/switch-pen-insert' for '(null)' GPIO lookup
Let's pass the consumer device down, by directly calling what
fwnode_gpiod_get_index() calls but pass the device used for devm. This
changes the message to look like this instead:
gpio-keys gpio-keys: using DT '/gpio-keys/switch-pen-insert' for '(null)' GPIO lookup
Note that callers of fwnode_gpiod_get_index() will still see the NULL
device pointer debug message, but there's not much we can do about that
because the API doesn't take a struct device.
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes: 8eb1f71e7a ("gpiolib: consolidate GPIO lookups")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ff08803ec ]
The hdmi@3d node's compatible string is "adi,adv7535" instead of
"adi,adv7533" or "adi,adv751*".
Fix the hdmi@3d node by means of:
* Use default register addresses for "cec", "edid" and "packet", because
there is no need to use a non-default address map.
* Add missing interrupt related properties.
* Drop "adi,input-*" properties which are only valid for adv751*.
* Add VEXT_3V3 fixed regulator.
* Add "*-supply" properties, since most are required.
* Fix label names - s/adv7533/adv7535/.
Fixes: 65344b9bed ("arm64: dts: imx8mp-evk: Add HDMI support")
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 13ab6f174a ]
The SPI NOR bus routing on this board cannot go above 50 MHz,
set the clock frequency to maximum of 40 MHz to be within a
safe margin. Remove the comment as well.
Fixes: 562d222f23 ("arm64: dts: imx8mp: Add support for Data Modul i.MX8M Plus eDM SBC")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79978bff2e ]
We identified that the PHYs actually do not work since commit 7da7b84fee
("ARM: dts: imx6dl-yapp4: Move phy reset into switch node") as
a coincidence of several circumstances.
The reset signal is kept asserted by a pull-down resistor on the board
unless it is deasserted by GPIO from the SoC. This is to keep the switch
dead until it is configured properly by the kernel and user space.
Prior to the referenced commit the switch was reset by the FEC driver
and the reset GPIO was actively deasserted. The mdio-bus was scanned
and the attached switch and its PHYs were found and configured.
With the referenced commit the switch is reset by the qca8k driver.
Because of another bug in the qca8k driver, functionality of the reset
pin depends on its pre-kernel configuration. See commit c44fc98f0a
("net: dsa: qca8k: fix illegal usage of GPIO")
The problem did not appear until we removed support for the switch
and configuration of its reset pin from the bootloader.
To fix that, properly describe the internal mdio-bus configuration of
the qca8334 switch. The PHYs are internal to the switch and sit on its
internal mdio-bus.
Fixes: 7da7b84fee ("ARM: dts: imx6dl-yapp4: Move phy reset into switch node")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 023bd910d3 ]
This change does not have any functional effect. The switch works just
fine without this patch as it has full access to all the addresses
on the bus. This is simply a clean-up to set the node name address
and reg address to the same value.
Fixes: 15b43e497f ("ARM: dts: imx6dl-yapp4: Use correct pseudo PHY address for the switch")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a43e0fc5e9 ]
Unloading a modular pstore backend with records in pstorefs would
trigger the dput() double-drop warning:
WARNING: CPU: 0 PID: 2569 at fs/dcache.c:762 dput.part.0+0x3f3/0x410
Using the combo of d_drop()/dput() (as mentioned in
Documentation/filesystems/vfs.rst) isn't the right approach here, and
leads to the reference counting problem seen above. Use d_invalidate()
and update the code to not bother checking for error codes that can
never happen.
Suggested-by: Alexander Viro <viro@zeniv.linux.org.uk>
Fixes: 609e28bb13 ("pstore: Remove filesystem records when backend is unregistered")
Signed-off-by: Kees Cook <keescook@chromium.org>
[ Upstream commit 1394c1dec1 ]
If we're fragmenting on local output, the original packet may contain
ext data for the MCTP flows. We'll want this in the resulting fragment
skbs too.
So, do a skb_ext_copy() in the fragmentation path, and implement the
MCTP-specific parts of an ext copy operation.
Fixes: 67737c4572 ("mctp: Pass flow data & flow release events to drivers")
Reported-by: Jian Zhang <zhangjian.3032@bytedance.com>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 07ce1d4637 ]
In some case, the MTCL table will exist, but MTDS table will not.
So the SAR will init fail. This patch make MTCL and MTDS can exist
with no dependence.
Fixes: f965333e49 ("mt76: mt7921: introduce ACPI SAR support")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Leon Yen <leon.yen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c957280ef6 ]
From commit a304e1b828 ("[PATCH] Debug shared irqs"), there is a test
to make sure the shared irq handler should be able to handle the unexpected
event after deregistration. For this case, let's apply MT76_REMOVED flag to
indicate the device was removed and do not run into the resource access
anymore.
BUG: KASAN: use-after-free in mt7921_irq_handler+0xd8/0x100 [mt7921e]
Read of size 8 at addr ffff88824a7d3b78 by task rmmod/11115
CPU: 28 PID: 11115 Comm: rmmod Tainted: G W L 5.17.0 #10
Hardware name: Micro-Star International Co., Ltd. MS-7D73/MPG B650I
EDGE WIFI (MS-7D73), BIOS 1.81 01/05/2024
Call Trace:
<TASK>
dump_stack_lvl+0x6f/0xa0
print_address_description.constprop.0+0x1f/0x190
? mt7921_irq_handler+0xd8/0x100 [mt7921e]
? mt7921_irq_handler+0xd8/0x100 [mt7921e]
kasan_report.cold+0x7f/0x11b
? mt7921_irq_handler+0xd8/0x100 [mt7921e]
mt7921_irq_handler+0xd8/0x100 [mt7921e]
free_irq+0x627/0xaa0
devm_free_irq+0x94/0xd0
? devm_request_any_context_irq+0x160/0x160
? kobject_put+0x18d/0x4a0
mt7921_pci_remove+0x153/0x190 [mt7921e]
pci_device_remove+0xa2/0x1d0
__device_release_driver+0x346/0x6e0
driver_detach+0x1ef/0x2c0
bus_remove_driver+0xe7/0x2d0
? __check_object_size+0x57/0x310
pci_unregister_driver+0x26/0x250
__do_sys_delete_module+0x307/0x510
? free_module+0x6a0/0x6a0
? fpregs_assert_state_consistent+0x4b/0xb0
? rcu_read_lock_sched_held+0x10/0x70
? syscall_enter_from_user_mode+0x20/0x70
? trace_hardirqs_on+0x1c/0x130
do_syscall_64+0x5c/0x80
? trace_hardirqs_on_prepare+0x72/0x160
? do_syscall_64+0x68/0x80
? trace_hardirqs_on_prepare+0x72/0x160
entry_SYSCALL_64_after_hwframe+0x44/0xae
Reported-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Closes: https://lore.kernel.org/linux-wireless/CABXGCsOdvVwdLmSsC8TZ1jF0UOg_F_W3wqLECWX620PUkvNk=A@mail.gmail.com/
Fixes: 9270270d62 ("wifi: mt76: mt7921: fix PCI DMA hang after reboot")
Tested-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de88827751 ]
Sync the value of HIF_TXD_V2_1 with firmware to let it correctly fill
TXD values for HW path.
Fixes: 98686cd216 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Benjamin Lin <benjamin-jw.lin@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3ad99be7c ]
The efuse data starts from the 48th bytes instead of 64th bytes in the
returned event skb.
Fixes: 98686cd216 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d52c97592f ]
The EHT MCS map subfield of 20 MHz-Only is not present in the EHT
capability of AP, so STA does not need to parse the subfield.
Moreover, AP should parse the subfield only if STA is 20 MHz-Only, which
can be confirmed by checking supported channel width in HE capability.
Fixes: 92aa2da9fa ("wifi: mt76: mt7996: enable EHT support in firmware")
Co-developed-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Benjamin Lin <benjamin-jw.lin@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c832c228f ]
This patch fixes the following TWT issues:
- Change table_mask to u16 to support up to 16 TWT stations
- Reject TWT flows for duplicated establishment
- Fix possible unaligned pointer
- Remove unsupported TWT_CONTROL_WAKE_DUR_UNIT flag
- The minimum TWT duration supported by mt7996 chipsets is 64. Reply
with TWT_SETUP_CMD_DICTATE if the min_twt_dur is smaller than 64
Fixes: 98686cd216 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51d915cbee ]
Some of the names for the Tegra234 DLA clients are not unique and do not
align with the name of the client ID definitions. Therefore, it is not
possible to determine the exact DLA client from messages that print the
client name. Fix this by correcting the DLA memory client names for
Tegra234 to align with the name of the corresponding memory client ID.
Note that although the client names are also used by the interconnect
framework, interconnect support for the DLA clients has not been added
and so this issue does not impact the interconnect support.
Fixes: 5cd24ca098 ("memory: tegra: Add DLA clients for Tegra234")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20240220124430.19072-1-jonathanh@nvidia.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3baa4c5143 ]
When the development chip ROM was added, the "direct-mapped" compatible
value was already obsolete. In addition, the device node lacked the
accompanying "probe-type" property, causing the old physmap_of_core
driver to fall back to trying all available probe types.
Unfortunately this fallback was lost when the DT and pdata cases were
merged.
Fix this by using the modern "mtd-rom" compatible value instead.
Fixes: 5c3f5edbe0 ("ARM: realview: add flash devices to the PB1176 DTS")
Fixes: 642b1e8dbe ("mtd: maps: Merge physmap_of.c into physmap-core.c")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3ec643947 ]
This reverts commit fcf690b0b4.
When using a wilc1000 chip over a spi bus, users can optionally define a
reset gpio and a chip enable gpio. The reset line of wilc1000 is active
low, so to hold the chip in reset, a low (physical) value must be applied.
The corresponding device tree binding documentation was introduced by
commit f31ee3c0a5 ("wilc1000: Document enable-gpios and reset-gpios
properties") and correctly indicates that the reset line is an active-low
signal. The corresponding driver part, brought by commit ec031ac479
("wilc1000: Add reset/enable GPIO support to SPI driver") was applying the
correct logic. But commit fcf690b0b4 ("wifi: wilc1000: use correct
sequence of RESET for chip Power-UP/Down") eventually flipped this logic
and started misusing the gpiod APIs, applying an inverted logic when
powering up/down the chip (for example, setting the reset line to a logic
"1" during power up, which in fact asserts the reset line when device tree
describes the reset line as GPIO_ACTIVE_LOW). As a consequence, any
platform currently using the driver in SPI mode must use a faulty reset
line description in device tree, or else chip will be maintained in reset
and will not even allow to bring up the chip.
Fix reset line usage by inverting back the gpiod APIs usage, setting the
reset line to the logic value "0" when powering the chip, and the logic
value "1" when powering off the chip.
Fixes: fcf690b0b4 ("wifi: wilc1000: use correct sequence of RESET for chip Power-UP/Down")
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240217-wilc_1000_reset_line-v2-1-b216f433d7d5@bootlin.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b6345e3fc ]
SDHCI nodes defined in the top-level AM64 SoC dtsi files are incomplete
and will not be functional unless they are extended.
As the attached SD/eMMC is only known about at the board integration level,
these nodes should only be enabled when provided with this information.
Disable the SDHCI nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20231117163339.89952-2-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Stable-dep-of: 379c7752bb ("arm64: dts: ti: k3-am64-main: Fix ITAP/OTAP values for MMC")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4669288219 ]
bootph-all as phase tag was added to dt-schema
(dtschema/schemas/bootph.yaml) to describe various node usage during
boot phases with DT.
Describe the same for AM642-sk boot devices.
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230911172902.1057417-4-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Stable-dep-of: 379c7752bb ("arm64: dts: ti: k3-am64-main: Fix ITAP/OTAP values for MMC")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 33830e0777 ]
bootph-all as phase tag was added to dt-schema
(dtschema/schemas/bootph.yaml) to describe various node usage during
boot phases with DT.
Describe the same for AM642-evm boot devices.
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230911172902.1057417-3-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Stable-dep-of: 379c7752bb ("arm64: dts: ti: k3-am64-main: Fix ITAP/OTAP values for MMC")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d29a6cf980 ]
Only Tx and Rx Signal lines for wkup_uart0 are brought out on
the J784S4 EVM from SoC, but CTS and RTS signal lines are not
brought on the EVM. Thus, remove pinmux for CTS and RTS signal
lines for wkup_uart0 in J784S4.
Fixes: 6fa5d37a2f ("arm64: dts: ti: k3-j784s4-evm: Add mcu and wakeup uarts")
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Link: https://lore.kernel.org/r/20240214105846.1096733-5-b-kapoor@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28e5b74d52 ]
Only Tx and Rx Signal lines for wkup_uart0 are brought out on
the Common Proc Board through SoM, but CTS and RTS signal lines
are not brought on the board. Thus, remove pinmux for CTS and RTS
signal lines for wkup_uart0 in J721S2.
Fixes: f5e9ee0b35 ("arm64: dts: ti: k3-j721s2-common-proc-board: Add uart pinmux")
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Link: https://lore.kernel.org/r/20240214105846.1096733-4-b-kapoor@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78e886ba2b ]
Avoid the following warnings by removing the ena_select_queue() function
and rely on the net core to do the queue selection, The issue happen
when an skb received from an interface with more queues than ena is
forwarded to the ena interface.
[ 1176.159959] eth0 selects TX queue 11, but real number of TX queues is 8
[ 1176.863976] eth0 selects TX queue 14, but real number of TX queues is 8
[ 1180.767877] eth0 selects TX queue 14, but real number of TX queues is 8
[ 1188.703742] eth0 selects TX queue 14, but real number of TX queues is 8
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Kamal Heib <kheib@redhat.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b50155cb0d ]
The caller of the function freq_qos_add_request() checks again a non
zero value but freq_qos_add_request() can return '1' if the request
already exists. Therefore, the setup function fails while the QoS
request actually did not failed.
Fix that by changing the check against a negative value like all the
other callers of the function.
Fixes: 0e8f68d7f0 ("Add CPU energy model based support")
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1ea6db35f ]
An old cleanup went a little too far and causes a warning with clang-16
and higher as it breaks control flow integrity (KCFI) rules:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy_shim.c:64:34: error: cast from 'void (*)(struct brcms_phy *)' to 'void (*)(void *)' converts to incompatible function type [-Werror,-Wcast-function-type-strict]
64 | brcms_init_timer(physhim->wl, (void (*)(void *))fn,
| ^~~~~~~~~~~~~~~~~~~~
Change this one instance back to passing a void pointer so it can be
used with the timer callback interface.
Fixes: d89a4c8060 ("staging: brcm80211: removed void * from softmac phy")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240213100548.457854-1-arnd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0feda94c86 ]
On many systems that have an AMD IOMMU the following sequence of
warnings is observed during bootup.
```
pci 0000:00:00.2 can't derive routing for PCI INT A
pci 0000:00:00.2: PCI INT A: not connected
```
This series of events happens because of the IOMMU initialization
sequence order and the lack of _PRT entries for the IOMMU.
During initialization the IOMMU driver first enables the PCI device
using pci_enable_device(). This will call acpi_pci_irq_enable()
which will check if the interrupt is declared in a PCI routing table
(_PRT) entry. According to the PCI spec [1] these routing entries
are only required under PCI root bridges:
The _PRT object is required under all PCI root bridges
The IOMMU is directly connected to the root complex, so there is no
parent bridge to look for a _PRT entry. The first warning is emitted
since no entry could be found in the hierarchy. The second warning is
then emitted because the interrupt hasn't yet been configured to any
value. The pin was configured in pci_read_irq() but the byte in
PCI_INTERRUPT_LINE return 0xff which means "Unknown".
After that sequence of events pci_enable_msi() is called and this
will allocate an interrupt.
That is both of these warnings are totally harmless because the IOMMU
uses MSI for interrupts. To avoid even trying to probe for a _PRT
entry mark the IOMMU as IRQ managed. This avoids both warnings.
Link: https://uefi.org/htmlspecs/ACPI_Spec_6_4_html/06_Device_Configuration/Device_Configuration.html?highlight=_prt#prt-pci-routing-table [1]
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Fixes: cffe0a2b5a ("x86, irq: Keep balance of IOAPIC pin reference count")
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Link: https://lore.kernel.org/r/20240122233400.1802-1-mario.limonciello@amd.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4acd21a45c ]
Update the architecture dependency to be the generic Tegra
because the driver works on the four latest Tegra generations
not just Tegra210, if you build a kernel with a specific
ARCH_TEGRA_xxx_SOC option that excludes Tegra210 you don't get
this driver.
Fixes: 46a88534af ("bus: Add support for Tegra ACONNECT")
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Jon Hunter <jonathanh@nvidia.com>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c99b337a8 ]
AM62 USB works with some devices, while failing to operate with others.
[ 560.189822] xhci-hcd xhci-hcd.4.auto: xHCI Host Controller
[ 560.195631] xhci-hcd xhci-hcd.4.auto: new USB bus registered, assigned bus number 2
[ 574.388509] xhci-hcd xhci-hcd.4.auto: can't setup: -110
[ 574.393814] xhci-hcd xhci-hcd.4.auto: USB bus 2 deregistered
[ 574.399544] xhci-hcd: probe of xhci-hcd.4.auto failed with error -110
This seems to be related to LPM (Link Power Management), and disabling it
turns USB into reliable working state.
As per AM62 reference manual:
> 4.8.2.1 USB2SS Unsupported Features
>
> The following features are not supported on this family of devices:
> ...
> - USB 2.0 ECN: Link Power Management (LPM)
> ...
Fixes: 2240f96cf3 ("arm64: dts: ti: k3-am62-main: Add support for USB")
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/20240209130213.38908-1-andrejs.cainikovs@gmail.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb5942b77c ]
wilc_netdev_cleanup currently triggers a KASAN warning, which can be
observed on interface registration error path, or simply by
removing the module/unbinding device from driver:
echo spi0.1 > /sys/bus/spi/drivers/wilc1000_spi/unbind
==================================================================
BUG: KASAN: slab-use-after-free in wilc_netdev_cleanup+0x508/0x5cc
Read of size 4 at addr c54d1ce8 by task sh/86
CPU: 0 PID: 86 Comm: sh Not tainted 6.8.0-rc1+ #117
Hardware name: Atmel SAMA5
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x34/0x58
dump_stack_lvl from print_report+0x154/0x500
print_report from kasan_report+0xac/0xd8
kasan_report from wilc_netdev_cleanup+0x508/0x5cc
wilc_netdev_cleanup from wilc_bus_remove+0xc8/0xec
wilc_bus_remove from spi_remove+0x8c/0xac
spi_remove from device_release_driver_internal+0x434/0x5f8
device_release_driver_internal from unbind_store+0xbc/0x108
unbind_store from kernfs_fop_write_iter+0x398/0x584
kernfs_fop_write_iter from vfs_write+0x728/0xf88
vfs_write from ksys_write+0x110/0x1e4
ksys_write from ret_fast_syscall+0x0/0x1c
[...]
Allocated by task 1:
kasan_save_track+0x30/0x5c
__kasan_kmalloc+0x8c/0x94
__kmalloc_node+0x1cc/0x3e4
kvmalloc_node+0x48/0x180
alloc_netdev_mqs+0x68/0x11dc
alloc_etherdev_mqs+0x28/0x34
wilc_netdev_ifc_init+0x34/0x8ec
wilc_cfg80211_init+0x690/0x910
wilc_bus_probe+0xe0/0x4a0
spi_probe+0x158/0x1b0
really_probe+0x270/0xdf4
__driver_probe_device+0x1dc/0x580
driver_probe_device+0x60/0x140
__driver_attach+0x228/0x5d4
bus_for_each_dev+0x13c/0x1a8
bus_add_driver+0x2a0/0x608
driver_register+0x24c/0x578
do_one_initcall+0x180/0x310
kernel_init_freeable+0x424/0x484
kernel_init+0x20/0x148
ret_from_fork+0x14/0x28
Freed by task 86:
kasan_save_track+0x30/0x5c
kasan_save_free_info+0x38/0x58
__kasan_slab_free+0xe4/0x140
kfree+0xb0/0x238
device_release+0xc0/0x2a8
kobject_put+0x1d4/0x46c
netdev_run_todo+0x8fc/0x11d0
wilc_netdev_cleanup+0x1e4/0x5cc
wilc_bus_remove+0xc8/0xec
spi_remove+0x8c/0xac
device_release_driver_internal+0x434/0x5f8
unbind_store+0xbc/0x108
kernfs_fop_write_iter+0x398/0x584
vfs_write+0x728/0xf88
ksys_write+0x110/0x1e4
ret_fast_syscall+0x0/0x1c
[...]
David Mosberger-Tan initial investigation [1] showed that this
use-after-free is due to netdevice unregistration during vif list
traversal. When unregistering a net device, since the needs_free_netdev has
been set to true during registration, the netdevice object is also freed,
and as a consequence, the corresponding vif object too, since it is
attached to it as private netdevice data. The next occurrence of the loop
then tries to access freed vif pointer to the list to move forward in the
list.
Fix this use-after-free thanks to two mechanisms:
- navigate in the list with list_for_each_entry_safe, which allows to
safely modify the list as we go through each element. For each element,
remove it from the list with list_del_rcu
- make sure to wait for RCU grace period end after each vif removal to make
sure it is safe to free the corresponding vif too (through
unregister_netdev)
Since we are in a RCU "modifier" path (not a "reader" path), and because
such path is expected not to be concurrent to any other modifier (we are
using the vif_mutex lock), we do not need to use RCU list API, that's why
we can benefit from list_for_each_entry_safe.
[1] https://lore.kernel.org/linux-wireless/ab077dbe58b1ea5de0a3b2ca21f275a07af967d2.camel@egauge.net/
Fixes: 8399918f30 ("staging: wilc1000: use RCU list to maintain vif interfaces list")
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240212-wilc_rework_deinit-v1-1-9203ae56c27f@bootlin.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3093fa3353 ]
It is still possible to compile-test a kernel without CONFIG_COMMON_CLK
for some ancient ARM boards or other architectures, but this causes a
link failure in the qcom-cpufreq-hw driver:
ERROR: modpost: "devm_clk_hw_register" [drivers/cpufreq/qcom-cpufreq-hw.ko] undefined!
ERROR: modpost: "devm_of_clk_add_hw_provider" [drivers/cpufreq/qcom-cpufreq-hw.ko] undefined!
ERROR: modpost: "of_clk_hw_onecell_get" [drivers/cpufreq/qcom-cpufreq-hw.ko] undefined!
Add a Kconfig dependency here to make sure this always work. Apparently
this bug has been in the kernel for a while without me running into it
on randconfig builds as COMMON_CLK is almost always enabled.
I have cross-checked by building an allmodconfig kernel with COMMON_CLK
disabled, which showed no other driver having this problem.
Fixes: 4370232c72 ("cpufreq: qcom-hw: Add CPU clock provider support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1af98c3e53 ]
The mtu3 usb controllers don't list the xhci clock, though they require
it, and thus rely on the bootloader leaving it on in order to work.
When booting with the upstream arm64 defconfig, the usb controllers will
defer probe until modules have loaded since they have an indirect
dependency on CONFIG_MTK_CMDQ, which is configured as a module. However
at the point where modules are loaded, unused clocks are also disabled,
causing the usb controllers to probe without the xhci clock enabled and
fail to probe:
mtu3 11201000.usb: clks of sts1 are not stable!
mtu3 11201000.usb: device enable failed -110
mtu3 11201000.usb: mtu3 hw init failed:-110
mtu3 11201000.usb: failed to initialize gadget
mtu3: probe of 11201000.usb failed with error -110
(and same for the one at 11281000)
Add the missing clock for the usb controllers so that they can
successfully probe without relying on the bootloader state.
Fixes: f6c3e61c54 ("arm64: dts: mediatek: mt8186: Add MTU3 nodes")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20240213-mt8186-ssusb-domain-clk-fix-v2-2-1f981d35f3fd@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a00d4a98af ]
The ssusb power domains currently don't list any clocks, despite
depending on some, and thus rely on the bootloader leaving the required
clocks on in order to work.
When booting with the upstream arm64 defconfig, the power domain
controller will defer probe until modules have loaded since it has an
indirect dependency on CONFIG_MTK_CMDQ, which is configured as a module.
However at the point where modules are loaded, unused clocks are also
disabled, causing the ssusb domains to fail to be enabled and
consequently the controller to fail probe:
mtk-power-controller 10006000.syscon:power-controller: /soc/syscon@10006000/power-controller/power-domain@4: failed to power on domain: -110
mtk-power-controller: probe of 10006000.syscon:power-controller failed with error -110
Add the missing clocks for the ssusb power domains so that they can
successfully probe without relying on the bootloader state.
Fixes: d9e43c1e7a ("arm64: dts: mt8186: Add power domains controller")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20240213-mt8186-ssusb-domain-clk-fix-v2-1-1f981d35f3fd@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 724c4bf0e4 ]
The qfprom actually is bigger than 0x1000, so adjust the reg.
Note that the non-ECC-corrected qfprom can be found at 0xfc4b8000
(-0x4000). The current reg points to the ECC-corrected qfprom block
which should have equivalent values at all offsets compared to the
non-corrected version.
[luca@z3ntu.xyz: extract to standalone patch and adjust for review
comments]
Fixes: c59ffb5193 ("arm: dts: msm8974: Add thermal zones, tsens and qfprom nodes")
Signed-off-by: Craig Tatlor <ctatlor97@gmail.com>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240210-msm8974-qfprom-v3-1-26c424160334@z3ntu.xyz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 178c54666f ]
Currently tracing is supposed not to allow for bpf_spin_{lock,unlock}()
helper calls. This is to prevent deadlock for the following cases:
- there is a prog (prog-A) calling bpf_spin_{lock,unlock}().
- there is a tracing program (prog-B), e.g., fentry, attached
to bpf_spin_lock() and/or bpf_spin_unlock().
- prog-B calls bpf_spin_{lock,unlock}().
For such a case, when prog-A calls bpf_spin_{lock,unlock}(),
a deadlock will happen.
The related source codes are below in kernel/bpf/helpers.c:
notrace BPF_CALL_1(bpf_spin_lock, struct bpf_spin_lock *, lock)
notrace BPF_CALL_1(bpf_spin_unlock, struct bpf_spin_lock *, lock)
notrace is supposed to prevent fentry prog from attaching to
bpf_spin_{lock,unlock}().
But actually this is not the case and fentry prog can successfully
attached to bpf_spin_lock(). Siddharth Chintamaneni reported
the issue in [1]. The following is the macro definition for
above BPF_CALL_1:
#define BPF_CALL_x(x, name, ...) \
static __always_inline \
u64 ____##name(__BPF_MAP(x, __BPF_DECL_ARGS, __BPF_V, __VA_ARGS__)); \
typedef u64 (*btf_##name)(__BPF_MAP(x, __BPF_DECL_ARGS, __BPF_V, __VA_ARGS__)); \
u64 name(__BPF_REG(x, __BPF_DECL_REGS, __BPF_N, __VA_ARGS__)); \
u64 name(__BPF_REG(x, __BPF_DECL_REGS, __BPF_N, __VA_ARGS__)) \
{ \
return ((btf_##name)____##name)(__BPF_MAP(x,__BPF_CAST,__BPF_N,__VA_ARGS__));\
} \
static __always_inline \
u64 ____##name(__BPF_MAP(x, __BPF_DECL_ARGS, __BPF_V, __VA_ARGS__))
#define BPF_CALL_1(name, ...) BPF_CALL_x(1, name, __VA_ARGS__)
The notrace attribute is actually applied to the static always_inline function
____bpf_spin_{lock,unlock}(). The actual callback function
bpf_spin_{lock,unlock}() is not marked with notrace, hence
allowing fentry prog to attach to two helpers, and this
may cause the above mentioned deadlock. Siddharth Chintamaneni
actually has a reproducer in [2].
To fix the issue, a new macro NOTRACE_BPF_CALL_1 is introduced which
will add notrace attribute to the original function instead of
the hidden always_inline function and this fixed the problem.
[1] https://lore.kernel.org/bpf/CAE5sdEigPnoGrzN8WU7Tx-h-iFuMZgW06qp0KHWtpvoXxf1OAQ@mail.gmail.com/
[2] https://lore.kernel.org/bpf/CAE5sdEg6yUc_Jz50AnUXEEUh6O73yQ1Z6NV2srJnef0ZrQkZew@mail.gmail.com/
Fixes: d83525ca62 ("bpf: introduce bpf_spin_lock")
Signed-off-by: Yonghong Song <yonghong.song@linux.dev>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/bpf/20240207070102.335167-1-yonghong.song@linux.dev
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b49cabe63 ]
The commit adding the ChromeOS EC to the Asurada Devicetree mistakenly
added a base detection node. While tablet mode detection is supported by
CrosEC and used by Hayato, it is done through the cros-ec-keyb driver.
The base detection node, which is handled by the hid-google-hammer
driver, also provides tablet mode detection but by checking base
attachment status on the CrosEC, which is not supported for Asurada.
Hence, remove the unused CrosEC base detection node for Asurada.
Fixes: eb188a2aaa ("arm64: dts: mediatek: asurada: Add ChromeOS EC")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20240207-mt8192-asurada-cbas-remove-v1-1-04cb65951975@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04bd6411f5 ]
The cbas node is used to describe base detection functionality in the
ChromeOS EC, which is used for units that have a detachable keyboard and
thus rely on this functionality to switch between tablet and laptop
mode.
Despite the original commit having added the cbas node to the
mt8183-kukui.dtsi, not all machines that include it are detachables. In
fact all machines that include from mt8183-kukui-jacuzzi.dtsi are either
clamshells (ie normal laptops) or convertibles, meaning the keyboard can
be flipped but not detached. The detection for the keyboard getting
flipped is handled by the driver bound to the keyboard-controller node
in the EC.
Move the base detection node from the base kukui dtsi to the dtsis where
all machines are detachables, and thus actually make use of the node.
Fixes: 4fa8492d1e ("arm64: dts: mt8183: add cbas node under cros_ec")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240116-mt8183-kukui-cbas-remove-v3-1-055e21406e86@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 17ef8efc00 ]
As discussed in the past (commit 2d3916f318 ("ipv6: fix skb drops
in igmp6_event_query() and igmp6_event_report()")) I think the
synchronize_net() call in ipv6_mc_down() is not needed.
Under load, synchronize_net() can last between 200 usec and 5 ms.
KASAN seems to agree as well.
Fixes: f185de28d9 ("mld: add new workqueues for process mld events")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Taehee Yoo <ap420073@gmail.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4acf4e62cd ]
The config file contains a partial kernel configuration to be used by
`virtme-configkernel --custom'. The presumption is that the config file
contains all Kconfig options needed by the selftests from the directory.
In net/forwarding/config, many are missing, which manifests as spurious
failures when running the selftests, with messages about unknown device
types, qdisc kinds or classifier actions. Add the missing configurations.
Tested the resulting configuration using virtme-ng as follows:
# vng -b -f tools/testing/selftests/net/forwarding/config
# vng --user root
(within the VM:)
# make -C tools/testing/selftests TARGETS=net/forwarding run_tests
Signed-off-by: Petr Machata <petrm@nvidia.com>
Link: https://lore.kernel.org/r/025abded7ff9cea5874a7fe35dcd3fd41bf5e6ac.1706286755.git.petrm@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Stable-dep-of: f0ddf15f0a ("selftests: forwarding: Add missing multicast routing config entries")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0628c03934 ]
'-fPIC' as an option to the linker does not do what it seems like it
should. With ld.bfd, it is treated as '-f PIC', which does not make
sense based on the meaning of '-f':
-f SHLIB, --auxiliary SHLIB Auxiliary filter for shared object symbol table
When building with ld.lld (currently under review in a GitHub pull
request), it just errors out because '-f' means nothing and neither does
'-fPIC':
ld.lld: error: unknown argument '-fPIC'
'-fPIC' was blindly copied from CFLAGS when the vDSO stopped being
linked with '$(CC)', it should not be needed. Remove it to clear up the
build failure with ld.lld.
Fixes: 2b2a25845d ("s390/vdso: Use $(LD) instead of $(CC) to link vDSO")
Link: https://github.com/llvm/llvm-project/pull/75643
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Fangrui Song <maskray@google.com>
Link: https://lore.kernel.org/r/20240130-s390-vdso-drop-fpic-from-ldflags-v1-1-094ad104fc55@kernel.org
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 225d09d6e5 ]
When the device drivers are initialized, a sysfs directory
is created. This contains many attributes which are allocated with
kzalloc(). Should it fail, the memory for the attributes already
created is freed in attr_event_free(). Its second parameter is number
of attribute elements to delete. This parameter is off by one.
When i. e. the 10th attribute fails to get created, attributes
numbered 0 to 9 should be deleted. Currently only attributes
numbered 0 to 8 are deleted.
Fixes: 39d62336f5 ("s390/pai: add support for cryptography counters")
Reported-by: Sumanth Korikkar <sumanthk@linux.ibm.com>
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Acked-by: Sumanth Korikkar <sumanthk@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5bd4041cd ]
The firmware (later) actually uses the values even for keys
that are invalid as far as the host is concerned, later in
rekeying, and then only sets the low 48 bits since the PNs
are only 48 bits over the air. It does, however, compare the
full 64 bits later, obviously causing problems.
Remove the memset and use kzalloc instead to avoid any old
heap data leaking to the firmware. We already init all the
other fields in the struct anyway. This leaves the data set
to zero for any unused fields, so the firmware can look at
them safely even if they're not used right now.
Fixes: 79e561f0f0 ("iwlwifi: mvm: d3: implement RSC command version 5")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240206175739.462101146fef.I10f3855b99417af4247cff04af78dcbc6cb75c9c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e0e766bd8 ]
When retrieving the queue index ("SCD SSN") from the TX response,
it's currently masked with 0xFFF. However, now that we have queues
longer than 4k, that became wrong, so make the mask depend on the
hardware family.
This fixes an issue where if we get a single frame reclaim while
in the top half of an 8k long queue, we'd reclaim-wrap the queue
twice (once on this and then again on the next non-single reclaim)
which at least triggers the WARN_ON_ONCE() in iwl_txq_reclaim(),
but could have other negative side effects (such as unmapping a
frame that wasn't transmitted yet, and then taking an IOMMU fault)
as well.
Fixes: 7b3e42ea2e ("iwlwifi: support multiple tfd queue max sizes for different devices")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240205211151.4148a6ef54e0.I733a70f679c25f9f99097a8dcb3a1f8165da6997@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 903fad4394 ]
The .BTF_ids section is pre-filled with zeroed BTF ID entries during the
build and afterwards patched by resolve_btfids with correct values.
Since resolve_btfids always writes in host-native endianness, it relies
on libelf to do the translation when the target ELF is cross-compiled to
a different endianness (this was introduced in commit 61e8aeda93
("bpf: Fix libelf endian handling in resolv_btfids")).
Unfortunately, the translation will corrupt the flags fields of SET8
entries because these were written during vmlinux compilation and are in
the correct endianness already. This will lead to numerous selftests
failures such as:
$ sudo ./test_verifier 502 502
#502/p sleepable fentry accept FAIL
Failed to load prog 'Invalid argument'!
bpf_fentry_test1 is not sleepable
verification time 34 usec
stack depth 0
processed 0 insns (limit 1000000) max_states_per_insn 0 total_states 0 peak_states 0 mark_read 0
Summary: 0 PASSED, 0 SKIPPED, 1 FAILED
Since it's not possible to instruct libelf to translate just certain
values, let's manually bswap the flags (both global and entry flags) in
resolve_btfids when needed, so that libelf then translates everything
correctly.
Fixes: ef2c6f370a ("tools/resolve_btfids: Add support for 8-byte BTF sets")
Signed-off-by: Viktor Malik <vmalik@redhat.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/7b6bff690919555574ce0f13d2a5996cacf7bf69.1707223196.git.vmalik@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9707ac4fe2 ]
Instead of using magic offsets to access BTF ID set data, leverage types
from btf_ids.h (btf_id_set and btf_id_set8) which define the actual
layout of the data. Thanks to this change, set sorting should also
continue working if the layout changes.
This requires to sync the definition of 'struct btf_id_set8' from
include/linux/btf_ids.h to tools/include/linux/btf_ids.h. We don't sync
the rest of the file at the moment, b/c that would require to also sync
multiple dependent headers and we don't need any other defs from
btf_ids.h.
Signed-off-by: Viktor Malik <vmalik@redhat.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Daniel Xu <dxu@dxuuu.xyz>
Link: https://lore.kernel.org/bpf/ff7f062ddf6a00815fda3087957c4ce667f50532.1707223196.git.vmalik@redhat.com
Stable-dep-of: 903fad4394 ("tools/resolve_btfids: Fix cross-compilation to non-host endianness")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f62383558 ]
The driver only used the number of pwm channels to set the pwm_chip's
npwm member. The result is that if there are more capture channels than
PWM channels specified in the device tree, only a part of the capture
channel is usable. Fix that by passing the bigger channel count to the
pwm framework. This makes it possible that the .apply() callback is
called with .hwpwm >= pwm_num_devs, catch that case and return an error
code.
Fixes: c97267ae83 ("pwm: sti: Add PWM capture callback")
Link: https://lore.kernel.org/r/20240204212043.2951852-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d04d5882cd ]
The commit d51507098f ("printk: disable optimistic spin
during panic") added checks to avoid becoming a console waiter
if a panic is in progress.
However, the transition to panic can occur while there is
already a waiter. The current owner should not pass the lock to
the waiter because it might get stopped or blocked anytime.
Also the panic context might pass the console lock owner to an
already stopped waiter by mistake. It might happen when
console_flush_on_panic() ignores the current lock owner, for
example:
CPU0 CPU1
---- ----
console_lock_spinning_enable()
console_trylock_spinning()
[CPU1 now console waiter]
NMI: panic()
panic_other_cpus_shutdown()
[stopped as console waiter]
console_flush_on_panic()
console_lock_spinning_enable()
[print 1 record]
console_lock_spinning_disable_and_check()
[handover to stopped CPU1]
This results in panic() not flushing the panic messages.
Fix these problems by disabling all spinning operations
completely during panic().
Another advantage is that it prevents possible deadlocks caused
by "console_owner_lock". The panic() context does not need to
take it any longer. The lockless checks are safe because the
functions become NOPs when they see the panic in progress. All
operations manipulating the state are still synchronized by the
lock even when non-panic CPUs would notice the panic
synchronously.
The current owner might stay spinning. But non-panic() CPUs
would get stopped anyway and the panic context will never start
spinning.
Fixes: dbdda842fe ("printk: Add console owner and waiter logic to load balance console writes")
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20240207134103.1357162-12-john.ogness@linutronix.de
Signed-off-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 019b58dcb6 ]
During calculate vdev_stats_id, will compare vdev_stats_id with
ATH12K_INVAL_VDEV_STATS_ID by '<='. If vdev_stats_id is relatively
small, then assign ATH12K_INVAL_VDEV_STATS_ID to vdev_stats_id.
This logic is incorrect. Firstly, should use '>=' instead of '<=' to
check if this u8 variable exceeds the max valid range.
Secondly, should use the maximum value as comparison value.
Correct comparison symbols and use the maximum value
ATH12K_MAX_VDEV_STATS_ID for comparison.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240130040303.370590-3-quic_kangyang@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92a871ab9f ]
When the feature_flags and xdp_zc_max_segs fields were added to the libbpf
bpf_xdp_query_opts, the code writing them did not use the OPTS_SET() macro.
This causes libbpf to write to those fields unconditionally, which means
that programs compiled against an older version of libbpf (with a smaller
size of the bpf_xdp_query_opts struct) will have its stack corrupted by
libbpf writing out of bounds.
The patch adding the feature_flags field has an early bail out if the
feature_flags field is not part of the opts struct (via the OPTS_HAS)
macro, but the patch adding xdp_zc_max_segs does not. For consistency, this
fix just changes the assignments to both fields to use the OPTS_SET()
macro.
Fixes: 13ce2daa25 ("xsk: add new netlink attribute dedicated for ZC max frags")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20240206125922.1992815-1-toke@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b802e7b7e7 ]
Currently in ath11k_peer_assoc_h_he() rx_mcs_80 and rx_mcs_160
are used to calculate max_nss, see
if (support_160)
max_nss = min(rx_mcs_80, rx_mcs_160);
else
max_nss = rx_mcs_80;
Kernel test robot complains on uninitialized symbols:
drivers/net/wireless/ath/ath11k/mac.c:2321 ath11k_peer_assoc_h_he() error: uninitialized symbol 'rx_mcs_80'.
drivers/net/wireless/ath/ath11k/mac.c:2321 ath11k_peer_assoc_h_he() error: uninitialized symbol 'rx_mcs_160'.
drivers/net/wireless/ath/ath11k/mac.c:2323 ath11k_peer_assoc_h_he() error: uninitialized symbol 'rx_mcs_80'.
This is because there are some code paths that never set them, so
the assignment of max_nss can come from uninitialized variables.
This could result in some unknown issues since a wrong peer_nss
might be passed to firmware.
Change to initialize them to an invalid value at the beginning. This
makes sense because even max_nss gets an invalid value, due to either
or both of them being invalid, we can get an valid peer_nss with
following guard:
arg->peer_nss = min(sta->deflink.rx_nss, max_nss)
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Fixes: 3db26ecf71 ("ath11k: calculate the correct NSS of peer for HE capabilities")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202401311243.NyXwWZxP-lkp@intel.com/
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240202023547.11141-1-quic_bqiang@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 843a8851e8 ]
lib/test_blackhole_dev.c sets a variable that is never read, causing
this following building warning:
lib/test_blackhole_dev.c:32:17: warning: variable 'ethh' set but not used [-Wunused-but-set-variable]
Remove the variable struct ethhdr *ethh, which is unused.
Fixes: 509e56b37c ("blackhole_dev: add a selftest")
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec2cb52fcf ]
The GW71xx does not have a gpio controlled vbus regulator but it does
require some pinctrl. Remove the regulator and move the valid pinctrl
into the usbotg1 node.
Fixes: bd306fdb4e ("arm64: dts: imx8mm-venice-gw71xx: fix USB OTG VBUS")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f575957882 ]
The vf610 gpio driver is enabled by default for all i.MX machines,
without any option to disable it in a board-specific config file.
Most i.MX chipsets have no hardware for this driver. Change the default
to enable GPIO_VF610 for SOC_VF610 and disable it otherwise.
Add a text description after the bool type, this makes the driver
selectable by make config etc.
Fixes: 30a35c07d9 ("gpio: vf610: drop the SOC_VF610 dependency for GPIO_VF610")
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3b2c6c65b ]
When connecting to an AP, we currently initialize the rate
control only after associating. Since we now use firmware
to assign rates to auth/assoc frames rather than using the
data in the station and the firmware doesn't know, they're
transmitted using low mandatory rates. However, if the AP
advertised only higher supported rates we want to use them
to be nicer (it still must receive mandatory rates though),
so send the information to the firmware earlier to have it
know about it and be able to use it.
Fixes: 499d027904 ("wifi: iwlwifi: Use FW rate for non-data frames")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240128084842.ed7ab1c859c2.I4b4d4fc3905c8d8470fc0fee4648f25c950c9bb7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 902700d55d ]
In QCN9274, RX packet's multicast and broadcast(MCBC) flag is fetched
from RX descriptor's msdu_end info5 member but it is not correct
for QCN9274. Due to this with encryption, ARP request packet is wrongly
marked as MCBC packet and it is sent to mac80211 without setting
RX_FLAG_PN_VALIDATED & RX_FLAG_DECRYPTED flag. This results in packet
getting dropped in mac80211. Hence ping initiated from station to AP
fails.
Fix this by fetching correct MCBC flag in case of QCN9274.
For QC9274 MCBC flag should be fetched from RX descriptor's mpdu_start
info6 member.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: 8f04852e90 ("wifi: ath12k: Use msdu_end to check MCBC")
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240129065724.2310207-5-quic_rajkbhag@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 413e20e82e ]
Currently when connecting to an AP with 11AX-HE phy mode, host sends
WMI_VDEV_PARAM_SET_HEMU_MODE parameter to firmware after
WMI_PEER_ASSOC_CMDID command. This results in TXBF not working, because
firmware calculates TXBF values while handling WMI_PEER_ASSOC_CMDID,
however at that time WMI_VDEV_PARAM_SET_HEMU_MODE has not been sent yet.
See below log:
AP sends "VHT/HE/EHT NDP Announcement" to station, and station sends
"Action no Ack" of category code HE to AP, the "Nc Index" and
"Codebook Information" are wrong:
Issued action:
IEEE 802.11 Action No Ack, Flags: ........
IEEE 802.11 wireless LAN
Fixed parameters
Category code: HE (30)
HE Action: HE Compressed Beamforming And CQI (0)
Total length: 152
HE MIMO Control: 0x0004008018
.... .... .... .... .... .... .... .... .... .000 = Nc Index: 1 Column (0)
.... .... .... .... .... .... .... ..0. .... .... = Codebook Information: 0
Change to send WMI_VDEV_PARAM_SET_HEMU_MODE before WMI_PEER_ASSOC_CMDID,
then firmware will calculate the TXBF values with valid parameters
instead of empty values. TXBF works well and throughput performance is
improved from 80 Mbps to 130 Mbps with this patch.
Good action after this patch:
IEEE 802.11 Action No Ack, Flags: ........
IEEE 802.11 wireless LAN
Fixed parameters
Category code: HE (30)
HE Action: HE Compressed Beamforming And CQI (0)
Total length: 409
HE MIMO Control: 0x0004008219
.... .... .... .... .... .... .... .... .... .001 = Nc Index: 2 Columns (1)
.... .... .... .... .... .... .... ..1. .... .... = Codebook Information: 1
This change applies to all chipsets.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Fixes: 38dfe775d0 ("wifi: ath11k: push MU-MIMO params from hostapd to hardware")
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240131021832.17298-1-quic_bqiang@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24355fcb0d ]
The ath9k_wmi_event_tasklet() used in ath9k_htc assumes that all the data
structures have been fully initialised by the time it runs. However, because of
the order in which things are initialised, this is not guaranteed to be the
case, because the device is exposed to the USB subsystem before the ath9k driver
initialisation is completed.
We already committed a partial fix for this in commit:
8b3046abc9 ("ath9k_htc: fix NULL pointer dereference at ath9k_htc_tx_get_packet()")
However, that commit only aborted the WMI_TXSTATUS_EVENTID command in the event
tasklet, pairing it with an "initialisation complete" bit in the TX struct. It
seems syzbot managed to trigger the race for one of the other commands as well,
so let's just move the existing synchronisation bit to cover the whole
tasklet (setting it at the end of ath9k_htc_probe_device() instead of inside
ath9k_tx_init()).
Link: https://lore.kernel.org/r/ed1d2c66-1193-4c81-9542-d514c29ba8b8.bugreport@ubisectech.com
Fixes: 8b3046abc9 ("ath9k_htc: fix NULL pointer dereference at ath9k_htc_tx_get_packet()")
Reported-by: Ubisectech Sirius <bugreport@ubisectech.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240126140218.1033443-1-toke@toke.dk
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0088205248 ]
Some signals have external pullup resistors on the board and don't need
the internal ones to be enabled. Due to silicon errata ERR050080 let's
disable the internal pull resistors whererever possible and prevent
any unwanted behavior in case they wear out.
Fixes: 8668d8b2e6 ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a940ba3e4 ]
Some signals have external pullup resistors on the board and don't need
the internal ones to be enabled. Due to silicon errata ERR050080 let's
disable the internal pull resistors whererever possible and prevent
any unwanted behavior in case they wear out.
Fixes: de9618e84f ("arm64: dts: Add support for Kontron SL/BL i.MX8MM OSM-S")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 162aadaa0d ]
These signals are actively driven by the SoC or by the onboard
transceiver. There's no need to enable the internal pull resistors
and due to silicon errata ERR050080 let's disable the internal ones
to prevent any unwanted behavior in case they wear out.
Fixes: 8668d8b2e6 ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c6d9b5672a ]
These signals are actively driven by the SoC or by the onboard
transceiver. There's no need to enable the internal pull resistors
and due to silicon errata ERR050080 let's disable the internal ones
to prevent any unwanted behavior in case they wear out.
Fixes: de9618e84f ("arm64: dts: Add support for Kontron SL/BL i.MX8MM OSM-S")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f19e5bb91d ]
There are external pullup resistors on the board and due to silicon
errata ERR050080 let's disable the internal ones to prevent any
unwanted behavior in case they wear out.
Fixes: 8668d8b2e6 ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 96293af54f ]
There are external pullup resistors on the board and due to silicon
errata ERR050080 let's disable the internal ones to prevent any
unwanted behavior in case they wear out.
Fixes: de9618e84f ("arm64: dts: Add support for Kontron SL/BL i.MX8MM OSM-S")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ef61296d2 ]
After a recent change in the vmtest runner, this test started failing
sporadically.
Investigation showed that this test was subject to race condition which
got exacerbated after the vm runner change. The symptoms being that the
logic that waited for an ICMPv4 packet is naive and will break if 5 or
more non-ICMPv4 packets make it to tap0.
When ICMPv6 is enabled, the kernel will generate traffic such as ICMPv6
router solicitation...
On a system with good performance, the expected ICMPv4 packet would very
likely make it to the network interface promptly, but on a system with
poor performance, those "guarantees" do not hold true anymore.
Given that the test is IPv4 only, this change disable IPv6 in the test
netns by setting `net.ipv6.conf.all.disable_ipv6` to 1.
This essentially leaves "ping" as the sole generator of traffic in the
network namespace.
If this test was to be made IPv6 compatible, the logic in
`wait_for_packet` would need to be modified.
In more details...
At a high level, the test does:
- create a new namespace
- in `setup_redirect_target` set up lo, tap0, and link_err interfaces as
well as add 2 routes that attaches ingress/egress sections of
`test_lwt_redirect.bpf.o` to the xmit path.
- in `send_and_capture_test_packets` send an ICMP packet and read off
the tap interface (using `wait_for_packet`) to check that a ICMP packet
with the right size is read.
`wait_for_packet` will try to read `max_retry` (5) times from the tap0
fd looking for an ICMPv4 packet matching some criteria.
The problem is that when we set up the `tap0` interface, because IPv6 is
enabled by default, traffic such as Router solicitation is sent through
tap0, as in:
# tcpdump -r /tmp/lwt_redirect.pc
reading from file /tmp/lwt_redirect.pcap, link-type EN10MB (Ethernet)
04:46:23.578352 IP6 :: > ff02::1:ffc0:4427: ICMP6, neighbor solicitation, who has fe80::fcba:dff:fec0:4427, length 32
04:46:23.659522 IP6 :: > ff02::16: HBH ICMP6, multicast listener report v2, 1 group record(s), length 28
04:46:24.389169 IP 10.0.0.1 > 20.0.0.9: ICMP echo request, id 122, seq 1, length 108
04:46:24.618599 IP6 fe80::fcba:dff:fec0:4427 > ff02::16: HBH ICMP6, multicast listener report v2, 1 group record(s), length 28
04:46:24.619985 IP6 fe80::fcba:dff:fec0:4427 > ff02::2: ICMP6, router solicitation, length 16
04:46:24.767326 IP6 fe80::fcba:dff:fec0:4427 > ff02::16: HBH ICMP6, multicast listener report v2, 1 group record(s), length 28
04:46:28.936402 IP6 fe80::fcba:dff:fec0:4427 > ff02::2: ICMP6, router solicitation, length 16
If `wait_for_packet` sees 5 non-ICMPv4 packets, it will return 0, which is what we see in:
2024-01-31T03:51:25.0336992Z test_lwt_redirect_run:PASS:netns_create 0 nsec
2024-01-31T03:51:25.0341309Z open_netns:PASS:malloc token 0 nsec
2024-01-31T03:51:25.0344844Z open_netns:PASS:open /proc/self/ns/net 0 nsec
2024-01-31T03:51:25.0350071Z open_netns:PASS:open netns fd 0 nsec
2024-01-31T03:51:25.0353516Z open_netns:PASS:setns 0 nsec
2024-01-31T03:51:25.0356560Z test_lwt_redirect_run:PASS:setns 0 nsec
2024-01-31T03:51:25.0360140Z open_tuntap:PASS:open(/dev/net/tun) 0 nsec
2024-01-31T03:51:25.0363822Z open_tuntap:PASS:ioctl(TUNSETIFF) 0 nsec
2024-01-31T03:51:25.0367402Z open_tuntap:PASS:fcntl(O_NONBLOCK) 0 nsec
2024-01-31T03:51:25.0371167Z setup_redirect_target:PASS:open_tuntap 0 nsec
2024-01-31T03:51:25.0375180Z setup_redirect_target:PASS:if_nametoindex 0 nsec
2024-01-31T03:51:25.0379929Z setup_redirect_target:PASS:ip link add link_err type dummy 0 nsec
2024-01-31T03:51:25.0384874Z setup_redirect_target:PASS:ip link set lo up 0 nsec
2024-01-31T03:51:25.0389678Z setup_redirect_target:PASS:ip addr add dev lo 10.0.0.1/32 0 nsec
2024-01-31T03:51:25.0394814Z setup_redirect_target:PASS:ip link set link_err up 0 nsec
2024-01-31T03:51:25.0399874Z setup_redirect_target:PASS:ip link set tap0 up 0 nsec
2024-01-31T03:51:25.0407731Z setup_redirect_target:PASS:ip route add 10.0.0.0/24 dev link_err encap bpf xmit obj test_lwt_redirect.bpf.o sec redir_ingress 0 nsec
2024-01-31T03:51:25.0419105Z setup_redirect_target:PASS:ip route add 20.0.0.0/24 dev link_err encap bpf xmit obj test_lwt_redirect.bpf.o sec redir_egress 0 nsec
2024-01-31T03:51:25.0427209Z test_lwt_redirect_normal:PASS:setup_redirect_target 0 nsec
2024-01-31T03:51:25.0431424Z ping_dev:PASS:if_nametoindex 0 nsec
2024-01-31T03:51:25.0437222Z send_and_capture_test_packets:FAIL:wait_for_epacket unexpected wait_for_epacket: actual 0 != expected 1
2024-01-31T03:51:25.0448298Z (/tmp/work/bpf/bpf/tools/testing/selftests/bpf/prog_tests/lwt_redirect.c:175: errno: Success) test_lwt_redirect_normal egress test fails
2024-01-31T03:51:25.0457124Z close_netns:PASS:setns 0 nsec
When running in a VM which potential resource contrains, the odds that calling
`ping` is not scheduled very soon after bringing `tap0` up increases,
and with this the chances to get our ICMP packet pushed to position 6+
in the network trace.
To confirm this indeed solves the issue, I ran the test 100 times in a
row with:
errors=0
successes=0
for i in `seq 1 100`
do
./test_progs -t lwt_redirect/lwt_redirect_normal
if [ $? -eq 0 ]; then
successes=$((successes+1))
else
errors=$((errors+1))
fi
done
echo "successes: $successes/errors: $errors"
While this test would at least fail a couple of time every 10 runs, here
it ran 100 times with no error.
Fixes: 43a7c3ef8a ("selftests/bpf: Add lwt_xmit tests for BPF_REDIRECT")
Signed-off-by: Manu Bretelle <chantr4@gmail.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20240131053212.2247527-1-chantr4@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eaffb10b51 ]
devm_regulator_get_optional() returns -ENODEV if no supply can be found.
By introducing its usage, commit 788715b5f2 ("cpufreq: mediatek-hw:
Wait for CPU supplies before probing") caused the driver to fail probe
if no supply was present in any of the CPU DT nodes.
Use devm_regulator_get() instead since the CPUs do require supplies
even if not described in the DT. It will gracefully return a dummy
regulator if none is found in the DT node, allowing probe to succeed.
Fixes: 788715b5f2 ("cpufreq: mediatek-hw: Wait for CPU supplies before probing")
Reported-by: kernelci.org bot <bot@kernelci.org>
Closes: https://linux.kernelci.org/test/case/id/65b0b169710edea22852a3fa/
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit afe9867a0c ]
Make it easier to understand what the reg in those nodes is by using the
constants provided by qcom,q6dsp-lpass-ports.h.
Name nodes according to dt-binding expectations.
Fix for
```
arch/arm64/boot/dts/qcom/sdm845-oneplus-enchilada.dtb: service@4: dais: Unevaluated properties are not allowed ('qi2s@22', 'qi2s@23' were unexpected)
```
Fixes: b7b7342868 ("arm64: dts: qcom: sdm845-oneplus-*: add audio devices")
Signed-off-by: David Heidelberg <david@ixit.cz>
Reviewed-by: Luca Weiss <luca@z3ntu.xyz>
Link: https://lore.kernel.org/r/20231229200245.259689-1-david@ixit.cz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce6f6cffae ]
After the previous patch that speeded up the test (by avoiding neigh
discovery in IPv6), the BPF CI occasionally hits this error:
rcv tstamp unexpected pkt rcv tstamp: actual 0 == expected 0
The test complains about the cmsg returned from the recvmsg() does not
have the rcv timestamp. Setting skb->tstamp or not is
controlled by a kernel static key "netstamp_needed_key". The static
key is enabled whenever this is at least one sk with the SOCK_TIMESTAMP
set.
The test_redirect_dtime does use setsockopt() to turn on
the SOCK_TIMESTAMP for the reading sk. In the kernel
net_enable_timestamp() has a delay to enable the "netstamp_needed_key"
when CONFIG_JUMP_LABEL is set. This potential delay is the likely reason
for packet missing rcv timestamp occasionally.
This patch is to create udp sockets with SOCK_TIMESTAMP set.
It sends and receives some packets until the received packet
has a rcv timestamp. It currently retries at most 5 times with 1s
in between. This should be enough to wait for the "netstamp_needed_key".
It then holds on to the socket and only closes it at the end of the test.
This guarantees that the test has the "netstamp_needed_key" key turned
on from the beginning.
To simplify the udp sockets setup, they are sending/receiving packets
in the same netns (ns_dst is used) and communicate over the "lo" dev.
Hence, the patch enables the "lo" dev in the ns_dst.
Fixes: c803475fd8 ("bpf: selftests: test skb->tstamp in redirect_neigh")
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20240120060518.3604920-2-martin.lau@linux.dev
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 177f1d083a ]
BPF CI has been reporting the tc_redirect_dtime test failing
from time to time:
test_inet_dtime:PASS:setns src 0 nsec
(network_helpers.c:253: errno: No route to host) Failed to connect to server
close_netns:PASS:setns 0 nsec
test_inet_dtime:FAIL:connect_to_fd unexpected connect_to_fd: actual -1 < expected 0
test_tcp_clear_dtime:PASS:tcp ip6 clear dtime ingress_fwdns_p100 0 nsec
The connect_to_fd failure (EHOSTUNREACH) is from the
test_tcp_clear_dtime() test and it is the very first IPv6 traffic
after setting up all the links, addresses, and routes.
The symptom is this first connect() is always slow. In my setup, it
could take ~3s.
After some tracing and tcpdump, the slowness is mostly spent in
the neighbor solicitation in the "ns_fwd" namespace while
the "ns_src" and "ns_dst" are fine.
I forced the kernel to drop the neighbor solicitation messages.
I can then reproduce EHOSTUNREACH. What actually happen could be:
- the neighbor advertisement came back a little slow.
- the "ns_fwd" namespace concluded a neighbor discovery failure
and triggered the ndisc_error_report() => ip6_link_failure() =>
icmpv6_send(skb, ICMPV6_DEST_UNREACH, ICMPV6_ADDR_UNREACH, 0)
- the client's connect() reports EHOSTUNREACH after receiving
the ICMPV6_DEST_UNREACH message.
The neigh table of both "ns_src" and "ns_dst" namespace has already
been manually populated but not the "ns_fwd" namespace. This patch
fixes it by manually populating the neigh table also in the "ns_fwd"
namespace.
Although the namespace configuration part had been existed before
the tc_redirect_dtime test, still Fixes-tagging the patch when
the tc_redirect_dtime test was added since it is the only test
hitting it so far.
Fixes: c803475fd8 ("bpf: selftests: test skb->tstamp in redirect_neigh")
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20240120060518.3604920-1-martin.lau@linux.dev
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 67a48d937f ]
Currently, the logic used to select the 6 GHz band is incorrect,
which may cause 6 GHz supported channels to not be updated properly.
This is because the 6 GHz Max frequency supported by the driver is
being compared to the Max frequency supported on the board. If in
some cases, the 6 GHz Max frequency supported on the board is less
than the defined 6 GHz Max frequency, all 6 GHz channels are disabled.
To address this, compare the max frequency supported by the board to
the defined 6 GHz Minimum frequency by the driver.
Similarly, when a dual mac card supports both 6 GHz and 5 GHz radios,
if the 5 GHz radio gets enumerated first before 6 GHz, the checks in
ath12k_mac_setup_channels_rates() can cause the 5 GHz channels which
were enabled earlier to get disabled when the 6 GHz channel list is
updated. This is because the Min 6 GHz frequency defined in the driver
is 5945 MHz, which should be 5925 MHz since channel 2 is not considered
currently, but the firmware can pass 5925 MHz as the minimum.
Hence, update the Min frequency supported by the driver to 5925 MHz.
In addition, ensure that the channel list update to firmware updates
only the channels that the current radio (ar) supports rather than
considering the wiphy support. This would be required when multiple pdevs
are supported in a wiphy and they support different ranges of frequencies
or bands as in single wiphy support.
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240117062628.8260-1-quic_srirrama@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f5f30386c7 ]
There exists the following warning when building bpftool:
CC prog.o
prog.c: In function ‘profile_open_perf_events’:
prog.c:2301:24: warning: ‘calloc’ sizes specified with ‘sizeof’ in the earlier argument and not in the later argument [-Wcalloc-transposed-args]
2301 | sizeof(int), obj->rodata->num_cpu * obj->rodata->num_metric);
| ^~~
prog.c:2301:24: note: earlier argument should specify number of elements, later size of each element
Tested with the latest upstream GCC which contains a new warning option
-Wcalloc-transposed-args. The first argument to calloc is documented to
be number of elements in array, while the second argument is size of each
element, just switch the first and second arguments of calloc() to silence
the build warning, compile tested only.
Fixes: 47c09d6a9f ("bpftool: Introduce "prog profile" command")
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Quentin Monnet <quentin@isovalent.com>
Link: https://lore.kernel.org/bpf/20240116061920.31172-1-yangtiezhu@loongson.cn
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit efd4025376 ]
__sock_diag_cmd() and sock_diag_bind() read sock_diag_handlers[family]
without a lock held.
Use READ_ONCE()/WRITE_ONCE() annotations to avoid potential issues.
Fixes: 8ef874bfc7 ("sock_diag: Move the sock_ code to net/core/")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 788715b5f2 ]
Before proceeding with the probe and enabling frequency scaling for the
CPUs, make sure that all supplies feeding the CPUs have probed.
This fixes an issue observed on MT8195-Tomato where if the
mediatek-cpufreq-hw driver enabled the hardware (by writing to
REG_FREQ_ENABLE) before the SPMI controller driver (spmi-mtk-pmif),
behind which lies the big CPU supply, probed the platform would hang
shortly after with "rcu: INFO: rcu_preempt detected stalls on
CPUs/tasks" being printed in the log.
Fixes: 4855e26bcf ("cpufreq: mediatek-hw: Add support for CPUFREQ HW")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f661017e6d ]
cpufreq_cpu_get may return NULL. To avoid NULL-dereference check it
and return 0 in case of error.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: de322e0859 ("cpufreq: brcmstb-avs-cpufreq: AVS CPUfreq driver for Broadcom STB SoCs")
Signed-off-by: Anastasia Belova <abelova@astralinux.ru>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50180c7f8e ]
debugfs_create_dir() returns ERR_PTR and never return NULL.
As Russell suggested, this patch removes the error checking for
debugfs_create_dir(). This is because the DebugFS kernel API is developed
in a way that the caller can safely ignore the errors that occur during
the creation of DebugFS nodes. The debugfs APIs have a IS_ERR() judge in
start_creating() which can handle it gracefully. So these checks are
unnecessary.
Fixes: 5e6e3a92b9 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Suggested-by: Russell King (Oracle) <linux@armlinux.org.uk>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20230903030216.1509013-3-ruanjinjie@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 12cfc9c8d3 ]
Adding then removing a second vif currently makes the first vif not working
anymore. This is visible for example when we have a first interface
connected to some access point:
- create a wpa_supplicant.conf with some AP credentials
- wpa_supplicant -Dnl80211 -c /etc/wpa_supplicant.conf -i wlan0
- dhclient wlan0
- iw phy phy0 interface add wlan1 type managed
- iw dev wlan1 del
wlan0 does not manage properly traffic anymore (eg: ping not working)
This is due to vif mode being incorrectly reconfigured with some default
values in del_virtual_intf, affecting by default first vif.
Prevent first vif from being affected on second vif removal by removing vif
mode change command in del_virtual_intf
Fixes: 9bc061e880 ("staging: wilc1000: added support to dynamically add/remove interfaces")
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Co-developed-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240115-wilc_1000_fixes-v1-5-54d29463a738@bootlin.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 328efda22a ]
Commit 09ed8bfc52 ("wilc1000: Rename workqueue from "WILC_wq" to
"NETDEV-wq"") moved workqueue creation in wilc_netdev_ifc_init in order to
set the interface name in the workqueue name. However, while the driver
needs only one workqueue, the wilc_netdev_ifc_init is called each time we
add an interface over a phy, which in turns overwrite the workqueue with a
new one. This can be observed with the following commands:
for i in $(seq 0 10)
do
iw phy phy0 interface add wlan1 type managed
iw dev wlan1 del
done
ps -eo pid,comm|grep wlan
39 kworker/R-wlan0
98 kworker/R-wlan1
102 kworker/R-wlan1
105 kworker/R-wlan1
108 kworker/R-wlan1
111 kworker/R-wlan1
114 kworker/R-wlan1
117 kworker/R-wlan1
120 kworker/R-wlan1
123 kworker/R-wlan1
126 kworker/R-wlan1
129 kworker/R-wlan1
Fix this leakage by putting back hif_workqueue allocation in
wilc_cfg80211_init. Regarding the workqueue name, it is indeed relevant to
set it lowercase, however it is not attached to a specific netdev, so
enforcing netdev name in the name is not so relevant. Still, enrich the
name with the wiphy name to make it clear which phy is using the workqueue.
Fixes: 09ed8bfc52 ("wilc1000: Rename workqueue from "WILC_wq" to "NETDEV-wq"")
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Co-developed-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240115-wilc_1000_fixes-v1-3-54d29463a738@bootlin.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 205c50306a ]
With lockdep enabled, calls to the connect function from cfg802.11 layer
lead to the following warning:
=============================
WARNING: suspicious RCU usage
6.7.0-rc1-wt+ #333 Not tainted
-----------------------------
drivers/net/wireless/microchip/wilc1000/hif.c:386
suspicious rcu_dereference_check() usage!
[...]
stack backtrace:
CPU: 0 PID: 100 Comm: wpa_supplicant Not tainted 6.7.0-rc1-wt+ #333
Hardware name: Atmel SAMA5
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x34/0x48
dump_stack_lvl from wilc_parse_join_bss_param+0x7dc/0x7f4
wilc_parse_join_bss_param from connect+0x2c4/0x648
connect from cfg80211_connect+0x30c/0xb74
cfg80211_connect from nl80211_connect+0x860/0xa94
nl80211_connect from genl_rcv_msg+0x3fc/0x59c
genl_rcv_msg from netlink_rcv_skb+0xd0/0x1f8
netlink_rcv_skb from genl_rcv+0x2c/0x3c
genl_rcv from netlink_unicast+0x3b0/0x550
netlink_unicast from netlink_sendmsg+0x368/0x688
netlink_sendmsg from ____sys_sendmsg+0x190/0x430
____sys_sendmsg from ___sys_sendmsg+0x110/0x158
___sys_sendmsg from sys_sendmsg+0xe8/0x150
sys_sendmsg from ret_fast_syscall+0x0/0x1c
This warning is emitted because in the connect path, when trying to parse
target BSS parameters, we dereference a RCU pointer whithout being in RCU
critical section.
Fix RCU dereference usage by moving it to a RCU read critical section. To
avoid wrapping the whole wilc_parse_join_bss_param under the critical
section, just use the critical section to copy ies data
Fixes: c460495ee0 ("staging: wilc1000: fix incorrent type in initializer")
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240105075733.36331-3-alexis.lothore@bootlin.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09795bded2 ]
bcm4331 seems to not function correctly with QoS support. This may be due
to issues with currently available firmware or potentially a device
specific issue.
When queues that are not of the default "best effort" priority are
selected, traffic appears to not transmit out of the hardware while no
errors are returned. This behavior is present among all the other priority
queues: video, voice, and background. While this can be worked around by
setting a kernel parameter, the default behavior is problematic for most
users and may be difficult to debug. This patch offers a working out-of-box
experience for bcm4331 users.
Log of the issue (using ssh low-priority traffic as an example):
ssh -T -vvvv git@github.com
OpenSSH_9.6p1, OpenSSL 3.0.12 24 Oct 2023
debug1: Reading configuration data /etc/ssh/ssh_config
debug2: checking match for 'host * exec "/nix/store/q1c2flcykgr4wwg5a6h450hxbk4ch589-bash-5.2-p15/bin/bash -c '/nix/store/c015armnkhr6v18za0rypm7sh1i8js8w-gnupg-2.4.1/bin/gpg-connect-agent --quiet updatestartuptty /bye >/dev/null 2>&1'"' host github.com originally github.com
debug3: /etc/ssh/ssh_config line 5: matched 'host "github.com"'
debug1: Executing command: '/nix/store/q1c2flcykgr4wwg5a6h450hxbk4ch589-bash-5.2-p15/bin/bash -c '/nix/store/c015armnkhr6v18za0rypm7sh1i8js8w-gnupg-2.4.1/bin/gpg-connect-agent --quiet updatestartuptty /bye >/dev/null 2>&1''
debug3: command returned status 0
debug3: /etc/ssh/ssh_config line 5: matched 'exec "/nix/store/q1c2flcykgr4wwg5a6h450hxbk4ch589-bash-5.2-p15/bin/bash -c '/nix/store/c015armnkhr6v18za0r"'
debug2: match found
debug1: /etc/ssh/ssh_config line 9: Applying options for *
debug3: expanded UserKnownHostsFile '~/.ssh/known_hosts' -> '/home/binary-eater/.ssh/known_hosts'
debug3: expanded UserKnownHostsFile '~/.ssh/known_hosts2' -> '/home/binary-eater/.ssh/known_hosts2'
debug2: resolving "github.com" port 22
debug3: resolve_host: lookup github.com:22
debug3: channel_clear_timeouts: clearing
debug3: ssh_connect_direct: entering
debug1: Connecting to github.com [192.30.255.113] port 22.
debug3: set_sock_tos: set socket 3 IP_TOS 0x48
Fixes: e6f5b934fb ("b43: Add QOS support")
Signed-off-by: Rahul Rameshbabu <sergeantsagara@protonmail.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231231050300.122806-5-sergeantsagara@protonmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23d04d8c6b ]
When picking a CPU on task wakeup, select_idle_core() has to take
into account the scheduling domain where the function looks for the CPU.
This is because the "isolcpus" kernel command line option can remove CPUs
from the domain to isolate them from other SMT siblings.
This change replaces the set of CPUs allowed to run the task from
p->cpus_ptr by the intersection of p->cpus_ptr and sched_domain_span(sd)
which is stored in the 'cpus' argument provided by select_idle_cpu().
Fixes: 9fe1f127b9 ("sched/fair: Merge select_idle_core/cpu()")
Signed-off-by: Keisuke Nishimura <keisuke.nishimura@inria.fr>
Signed-off-by: Julia Lawall <julia.lawall@inria.fr>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20240110131707.437301-2-keisuke.nishimura@inria.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8aeaffef8c ]
When picking a CPU on task wakeup, select_idle_smt() has to take
into account the scheduling domain of @target. This is because the
"isolcpus" kernel command line option can remove CPUs from the domain to
isolate them from other SMT siblings.
This fix checks if the candidate CPU is in the target scheduling domain.
Commit:
df3cb4ea1f ("sched/fair: Fix wrong cpu selecting from isolated domain")
... originally introduced this fix by adding the check of the scheduling
domain in the loop.
However, commit:
3e6efe87cd ("sched/fair: Remove redundant check in select_idle_smt()")
... accidentally removed the check. Bring it back.
Fixes: 3e6efe87cd ("sched/fair: Remove redundant check in select_idle_smt()")
Signed-off-by: Keisuke Nishimura <keisuke.nishimura@inria.fr>
Signed-off-by: Julia Lawall <julia.lawall@inria.fr>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Vincent Guittot <vincent.guittot@linaro.org>
Link: https://lore.kernel.org/r/20240110131707.437301-1-keisuke.nishimura@inria.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 14274d0bd3 ]
So far, get_device_system_crosststamp() unconditionally passes
system_counterval.cycles to timekeeping_cycles_to_ns(). But when
interpolating system time (do_interp == true), system_counterval.cycles is
before tkr_mono.cycle_last, contrary to the timekeeping_cycles_to_ns()
expectations.
On x86, CONFIG_CLOCKSOURCE_VALIDATE_LAST_CYCLE will mitigate on
interpolating, setting delta to 0. With delta == 0, xtstamp->sys_monoraw
and xtstamp->sys_realtime are then set to the last update time, as
implicitly expected by adjust_historical_crosststamp(). On other
architectures, the resulting nonsense xtstamp->sys_monoraw and
xtstamp->sys_realtime corrupt the xtstamp (ts) adjustment in
adjust_historical_crosststamp().
Fix this by deriving xtstamp->sys_monoraw and xtstamp->sys_realtime from
the last update time when interpolating, by using the local variable
"cycles". The local variable already has the right value when
interpolating, unlike system_counterval.cycles.
Fixes: 2c756feb18 ("time: Add history to cross timestamp interface supporting slower devices")
Signed-off-by: Peter Hilber <peter.hilber@opensynergy.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: John Stultz <jstultz@google.com>
Link: https://lore.kernel.org/r/20231218073849.35294-4-peter.hilber@opensynergy.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87a4113088 ]
The cycle_between() helper checks if parameter test is in the open interval
(before, after). Colloquially speaking, this also applies to the counter
wrap-around special case before > after. get_device_system_crosststamp()
currently uses cycle_between() at the first call site to decide whether to
interpolate for older counter readings.
get_device_system_crosststamp() has the following problem with
cycle_between() testing against an open interval: Assume that, by chance,
cycles == tk->tkr_mono.cycle_last (in the following, "cycle_last" for
brevity). Then, cycle_between() at the first call site, with effective
argument values cycle_between(cycle_last, cycles, now), returns false,
enabling interpolation. During interpolation,
get_device_system_crosststamp() will then call cycle_between() at the
second call site (if a history_begin was supplied). The effective argument
values are cycle_between(history_begin->cycles, cycles, cycles), since
system_counterval.cycles == interval_start == cycles, per the assumption.
Due to the test against the open interval, cycle_between() returns false
again. This causes get_device_system_crosststamp() to return -EINVAL.
This failure should be avoided, since get_device_system_crosststamp() works
both when cycles follows cycle_last (no interpolation), and when cycles
precedes cycle_last (interpolation). For the case cycles == cycle_last,
interpolation is actually unneeded.
Fix this by changing cycle_between() into timestamp_in_interval(), which
now checks against the closed interval, rather than the open interval.
This changes the get_device_system_crosststamp() behavior for three corner
cases:
1. Bypass interpolation in the case cycles == tk->tkr_mono.cycle_last,
fixing the problem described above.
2. At the first timestamp_in_interval() call site, cycles == now no longer
causes failure.
3. At the second timestamp_in_interval() call site, history_begin->cycles
== system_counterval.cycles no longer causes failure.
adjust_historical_crosststamp() also works for this corner case,
where partial_history_cycles == total_history_cycles.
These behavioral changes should not cause any problems.
Fixes: 2c756feb18 ("time: Add history to cross timestamp interface supporting slower devices")
Signed-off-by: Peter Hilber <peter.hilber@opensynergy.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20231218073849.35294-3-peter.hilber@opensynergy.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e814b59e6c ]
Commit
cbebd68f59 ("x86/mm: Fix use of uninitialized buffer in sme_enable()")
'fixed' an issue in sme_enable() detected by static analysis, and broke
the common case in the process.
cmdline_find_option() will return < 0 on an error, or when the command
line argument does not appear at all. In this particular case, the
latter is not an error condition, and so the early exit is wrong.
Instead, without mem_encrypt= on the command line, the compile time
default should be honoured, which could be to enable memory encryption,
and this is currently broken.
Fix it by setting sme_me_mask to a preliminary value based on the
compile time default, and only omitting the command line argument test
when cmdline_find_option() returns an error.
[ bp: Drop active_by_default while at it. ]
Fixes: cbebd68f59 ("x86/mm: Fix use of uninitialized buffer in sme_enable()")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lore.kernel.org/r/20240126163918.2908990-2-ardb+git@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2427e70c1 ]
The mba_MBps feedback loop increases throttling when a group is using
more bandwidth than the target set by the user in the schemata file, and
decreases throttling when below target.
To avoid possibly stepping throttling up and down on every poll a flag
"delta_comp" is set whenever throttling is changed to indicate that the
actual change in bandwidth should be recorded on the next poll in
"delta_bw". Throttling is only reduced if the current bandwidth plus
delta_bw is below the user target.
This algorithm works well if the workload has steady bandwidth needs.
But it can go badly wrong if the workload moves to a different phase
just as the throttling level changed. E.g. if the workload becomes
essentially idle right as throttling level is increased, the value
calculated for delta_bw will be more or less the old bandwidth level.
If the workload then resumes, Linux may never reduce throttling because
current bandwidth plus delta_bw is above the target set by the user.
Implement a simpler heuristic by assuming that in the worst case the
currently measured bandwidth is being controlled by the current level of
throttling. Compute how much it may increase if throttling is relaxed to
the next higher level. If that is still below the user target, then it
is ok to reduce the amount of throttling.
Fixes: ba0f26d852 ("x86/intel_rdt/mba_sc: Prepare for feedback loop")
Reported-by: Xiaochen Shen <xiaochen.shen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Xiaochen Shen <xiaochen.shen@intel.com>
Link: https://lore.kernel.org/r/20240122180807.70518-1-tony.luck@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 54e35eb861 ]
If the BMEC (Bandwidth Monitoring Event Configuration) feature is
supported, the bandwidth events can be configured. The maximum supported
bandwidth bitmask can be read from CPUID:
CPUID_Fn80000020_ECX_x03 [Platform QoS Monitoring Bandwidth Event Configuration]
Bits Description
31:7 Reserved
6:0 Identifies the bandwidth sources that can be tracked.
While at it, move the mask checking to mon_config_write() before
iterating over all the domains. Also, print the valid bitmask when the
user tries to configure invalid event configuration value.
The CPUID details are documented in the Processor Programming Reference
(PPR) Vol 1.1 for AMD Family 19h Model 11h B1 - 55901 Rev 0.25 in the
Link tag.
Fixes: dc2a3e8579 ("x86/resctrl: Add interface to read mbm_total_bytes_config")
Signed-off-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206537
Link: https://lore.kernel.org/r/669896fa512c7451319fa5ca2fdb6f7e015b5635.1705359148.git.babu.moger@amd.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0976783bb1 ]
The QOS Memory Bandwidth Enforcement Limit is reported by
CPUID_Fn80000020_EAX_x01 and CPUID_Fn80000020_EAX_x02:
Bits Description
31:0 BW_LEN: Size of the QOS Memory Bandwidth Enforcement Limit.
Newer processors can support higher bandwidth limit than the current
hard-coded value. Remove latter and detect using CPUID instead. Also,
update the register variables eax and edx to match the AMD CPUID
definition.
The CPUID details are documented in the Processor Programming Reference
(PPR) Vol 1.1 for AMD Family 19h Model 11h B1 - 55901 Rev 0.25 in the
Link tag below.
Fixes: 4d05bf71f1 ("x86/resctrl: Introduce AMD QOS feature")
Signed-off-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206537
Link: https://lore.kernel.org/r/c26a8ca79d399ed076cf8bf2e9fbc58048808289.1705359148.git.babu.moger@amd.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e5647a723 ]
On 64-bit platforms, the pfn_to_kaddr() macro requires that the input
value is 64 bits in order to ensure that valid address bits don't get
lost when shifting that input by PAGE_SHIFT to calculate the physical
address to provide a virtual address for.
One such example is in pvalidate_pages() (used by SEV-SNP guests), where
the GFN in the struct used for page-state change requests is a 40-bit
bit-field, so attempts to pass this GFN field directly into
pfn_to_kaddr() ends up causing guest crashes when dealing with addresses
above the 1TB range due to the above.
Fix this issue with SEV-SNP guests, as well as any similar cases that
might cause issues in current/future code, by using an inline function,
instead of a macro, so that the input is implicitly cast to the
expected 64-bit input type prior to performing the shift operation.
While it might be argued that the issue is on the caller side, other
archs/macros have taken similar approaches to deal with instances like
this, such as ARM explicitly casting the input to phys_addr_t:
e48866647b ("ARM: 8396/1: use phys_addr_t in pfn_to_kaddr()")
A C inline function is even better though.
[ mingo: Refined the changelog some more & added __always_inline. ]
Fixes: 6c32117963 ("x86/sev: Add SNP-specific unaccepted memory support")
Suggested-by: Dave Hansen <dave.hansen@intel.com>
Suggested-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Michael Roth <michael.roth@amd.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20231122163700.400507-1-michael.roth@amd.com
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@surriel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f98364e926 ]
This patch is against CVE-2023-6270. The description of cve is:
A flaw was found in the ATA over Ethernet (AoE) driver in the Linux
kernel. The aoecmd_cfg_pkts() function improperly updates the refcnt on
`struct net_device`, and a use-after-free can be triggered by racing
between the free on the struct and the access through the `skbtxq`
global queue. This could lead to a denial of service condition or
potential code execution.
In aoecmd_cfg_pkts(), it always calls dev_put(ifp) when skb initial
code is finished. But the net_device ifp will still be used in
later tx()->dev_queue_xmit() in kthread. Which means that the
dev_put(ifp) should NOT be called in the success path of skb
initial code in aoecmd_cfg_pkts(). Otherwise tx() may run into
use-after-free because the net_device is freed.
This patch removed the dev_put(ifp) in the success path in
aoecmd_cfg_pkts(), and added dev_put() after skb xmit in tx().
Link: https://nvd.nist.gov/vuln/detail/CVE-2023-6270
Fixes: 7562f876cd ("[NET]: Rework dev_base via list_head (v3)")
Signed-off-by: Chun-Yi Lee <jlee@suse.com>
Link: https://lore.kernel.org/r/20240305082048.25526-1-jlee@suse.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ede3db506 ]
The "controllen" variable is type size_t (unsigned long). Casting it
to int could lead to an integer underflow.
The check_add_overflow() function considers the type of the destination
which is type int. If we add two positive values and the result cannot
fit in an integer then that's counted as an overflow.
However, if we cast "controllen" to an int and it turns negative, then
negative values *can* fit into an int type so there is no overflow.
Good: 100 + (unsigned long)-4 = 96 <-- overflow
Bad: 100 + (int)-4 = 96 <-- no overflow
I deleted the cast of the sizeof() as well. That's not a bug but the
cast is unnecessary.
Fixes: 9b0fc3c054 ("io_uring: fix types in io_recvmsg_multishot_overflow")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/138bd2e2-ede8-4bcc-aa7b-f3d9de167a37@moroto.mountain
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c55978024d ]
Move the actual user_msghdr / compat_msghdr into the send and receive
sides, respectively, so we can move the uaddr receive handling into its
own handler, and ditto the multishot with buffer selection logic.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Stable-dep-of: 8ede3db506 ("io_uring/net: fix overflow check in io_recvmsg_mshot_prep()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 52307ac4f2 ]
For recvmsg, we roll our own since we support buffer selections. This
isn't the case for sendmsg right now, but in preparation for doing so,
make the recvmsg copy helpers generic so we can call them from the
sendmsg side as well.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Stable-dep-of: 8ede3db506 ("io_uring/net: fix overflow check in io_recvmsg_mshot_prep()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 133e267ef4 ]
'days' is a s64 (from div_s64), and so should use a %lld specifier.
This was found by extending KUnit's assertion macros to use gcc's
__printf attribute.
Fixes: 2760105516 ("time: Improve performance of time64_to_tm()")
Signed-off-by: David Gow <davidgow@google.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Justin Stitt <justinstitt@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a549ed22c ]
The 'i' passed as an assertion message is a size_t, so should use '%zu',
not '%d'.
This was found by annotating the _MSG() variants of KUnit's assertions
to let gcc validate the format strings.
Fixes: bb95ebbe89 ("lib: Introduce CONFIG_MEMCPY_KUNIT_TEST")
Signed-off-by: David Gow <davidgow@google.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Justin Stitt <justinstitt@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d2733a026f ]
The correct format specifier for p - n (both p and n are pointers) is
%td, as the type should be ptrdiff_t.
This was discovered by annotating KUnit assertion macros with gcc's
printf specifier, but note that gcc incorrectly suggested a %d or %ld
specifier (depending on the pointer size of the architecture being
built).
Fixes: 0ea0908311 ("lib/cmdline: Allow get_options() to take 0 to validate the input")
Signed-off-by: David Gow <davidgow@google.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Daniel Latypov <dlatypov@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f2f793fba ]
KUnit's executor_test logs the filter string in KUNIT_ASSERT_EQ_MSG(),
but passed a random character from the filter, rather than the whole
string.
This was found by annotating KUNIT_ASSERT_EQ_MSG() to let gcc validate
the format string.
Fixes: 76066f93f1 ("kunit: add tests for filtering attributes")
Signed-off-by: David Gow <davidgow@google.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Daniel Latypov <dlatypov@google.com>
Reviewed-by: Rae Moar <rmoar@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2824083db7 ]
overlayfs relies on the filesystem setting DCACHE_OP_HASH or
DCACHE_OP_COMPARE to reject mounting over case-insensitive directories.
Since commit bb9cd9106b ("fscrypt: Have filesystems handle their
d_ops"), we set ->d_op through a hook in ->d_lookup, which
means the root dentry won't have them, causing the mount to accidentally
succeed.
In v6.7-rc7, the following sequence will succeed to mount, but any
dentry other than the root dentry will be a "weird" dentry to ovl and
fail with EREMOTE.
mkfs.ext4 -O casefold lower.img
mount -O loop lower.img lower
mount -t overlay -o lowerdir=lower,upperdir=upper,workdir=work ovl /mnt
Mounting on a subdirectory fails, as expected, because DCACHE_OP_HASH
and DCACHE_OP_COMPARE are properly set by ->lookup.
Fix by explicitly rejecting superblocks that allow case-insensitive
dentries. Yes, this will be solved when we move d_op configuration back
to ->s_d_op. Yet, we better have an explicit fix to avoid messing up
again.
While there, re-sort the entries to have more descriptive error messages
first.
Fixes: bb9cd9106b ("fscrypt: Have filesystems handle their d_ops")
Acked-by: Amir Goldstein <amir73il@gmail.com>
Reviewed-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20240221171412.10710-2-krisman@suse.de
Signed-off-by: Gabriel Krisman Bertazi <krisman@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24e16e385f ]
Add new mount options lowerdir+ and datadir+ that can be used to add
layers to lower layers stack one by one.
Unlike the legacy lowerdir mount option, special characters (i.e. colons
and cammas) are not unescaped with these new mount options.
The new mount options can be repeated to compose a large stack of lower
layers, but they may not be mixed with the lagacy lowerdir mount option,
because for displaying lower layers in mountinfo, we do not want to mix
escaped with unescaped lower layers path syntax.
Similar to data-only layer rules with the lowerdir mount option, the
datadir+ option must follow at least one lowerdir+ option and the
lowerdir+ option must not follow the datadir+ option.
If the legacy lowerdir mount option follows lowerdir+ and datadir+
mount options, it overrides them. Sepcifically, calling:
fsconfig(FSCONFIG_SET_STRING, "lowerdir", "", 0);
can be used to reset previously setup lower layers.
Suggested-by: Miklos Szeredi <miklos@szeredi.hu>
Link: https://lore.kernel.org/r/CAJfpegt7VC94KkRtb1dfHG8+4OzwPBLYqhtc8=QFUxpFJE+=RQ@mail.gmail.com/
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Stable-dep-of: 2824083db7 ("ovl: Always reject mounting over case-insensitive directories")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0cea4c097d ]
We are about to add new mount options for adding lowerdir one by one,
but those mount options will not support escaping.
For the existing case, where lowerdir mount option is provided as a colon
separated list, store the user provided (possibly escaped) string and
display it as is when showing the lowerdir mount option.
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Stable-dep-of: 2824083db7 ("ovl: Always reject mounting over case-insensitive directories")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ddb9fd7a54 ]
A while ago, we changed the way that select() and poll() preallocate
a temporary buffer just under the size of the static warning limit of
1024 bytes, as clang was frequently going slightly above that limit.
The warnings have recently returned and I took another look. As it turns
out, clang is not actually inherently worse at reserving stack space,
it just happens to inline do_select() into core_sys_select(), while gcc
never inlines it.
Annotate do_select() to never be inlined and in turn remove the special
case for the allocation size. This should give the same behavior for
both clang and gcc all the time and once more avoids those warnings.
Fixes: ad312f95d4 ("fs/select: avoid clang stack usage warning")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240216202352.2492798-1-arnd@kernel.org
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e7539ffc9a ]
Just like is done for the kworker performing nodes initialization,
gracefully handle the possible allocation failure of the RCU expedited
grace period main kworker.
While at it perform a rename of the related checking functions to better
reflect the expedited specifics.
Reviewed-by: Kalesh Singh <kaleshsingh@google.com>
Fixes: 9621fbee44 ("rcu: Move expedited grace period (GP) work to RT kthread_worker")
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Reviewed-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a636c5e6f8 ]
Under CONFIG_RCU_EXP_KTHREAD=y, the nodes initialization for expedited
grace periods is queued to a kworker. However if the allocation of that
kworker failed, the nodes initialization is performed synchronously by
the caller instead.
Now the check for kworker initialization failure relies on the kworker
pointer to be NULL while its value might actually encapsulate an
allocation failure error.
Make sure to handle this case.
Reviewed-by: Kalesh Singh <kaleshsingh@google.com>
Fixes: 9621fbee44 ("rcu: Move expedited grace period (GP) work to RT kthread_worker")
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Reviewed-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79ae56fc47 ]
All log messages in dasd.c use the printk variants of pr_*(). They all
add the name of the affected device manually to the log message.
This can be simplified by using the dev_*() variants of printk, which
include the device information and make a separate call to dev_name()
unnecessary.
The KMSG_COMPONENT and the pr_fmt() definition can be dropped. Note that
this removes the "dasd: " prefix from the one pr_info() call in
dasd_init(). However, the log message already provides all relevant
information.
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://lore.kernel.org/r/20240208164248.540985-10-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Stable-dep-of: c3116e62dd ("s390/dasd: fix double module refcount decrement")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9fe3eaea4a ]
If we have a ton of notifications coming in, we can be looping in here
for a long time. This can be problematic for various reasons, mostly
because we can starve userspace. If the application is waiting on N
events, then only re-run if we need more events.
Fixes: c0e0d6ba25 ("io_uring: add IORING_SETUP_DEFER_TASKRUN")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 592b480543 ]
A previous commit added looping around handling traditional task_work
as an optimization, and while that may seem like a good idea, it's also
possible to run into application starvation doing so. If the task_work
generation is bursty, we can get very deep task_work queues, and we can
end up looping in here for a very long time.
One immediately observable problem with that is handling network traffic
using provided buffers, where flooding incoming traffic and looping
task_work handling will very quickly lead to buffer starvation as we
keep running task_work rather than returning to the application so it
can handle the associated CQEs and also provide buffers back.
Fixes: 3a0c037b0e ("io_uring: batch task_work")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ea1d9b4a8 ]
write_cache_pages always clear the page dirty bit before calling into the
file systems, and leaves folios with a writeback failure without the
dirty bit after return. We also clear the per-block writeback bits for
writeback failures unless no I/O has submitted, which will leave the
folio in an inconsistent state where it doesn't have the folio dirty,
but one or more per-block dirty bits. This seems to be due the place
where the iomap_clear_range_dirty call was inserted into the existing
not very clearly structured code when adding per-block dirty bit support
and not actually intentional. Switch to always clearing the dirty on
writeback failure.
Fixes: 4ce02c6797 ("iomap: Add per-block dirty state tracking to improve performance")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20231207072710.176093-2-hch@lst.de
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15930da42f ]
For wq_update_node_max_active(), @off_cpu of -1 indicates that no CPU is
going down. The function was incorrectly calling cpumask_test_cpu() with -1
CPU leading to oopses like the following on some archs:
Unable to handle kernel paging request at virtual address ffff0002100296e0
..
pc : wq_update_node_max_active+0x50/0x1fc
lr : wq_update_node_max_active+0x1f0/0x1fc
...
Call trace:
wq_update_node_max_active+0x50/0x1fc
apply_wqattrs_commit+0xf0/0x114
apply_workqueue_attrs_locked+0x58/0xa0
alloc_workqueue+0x5ac/0x774
workqueue_init_early+0x460/0x540
start_kernel+0x258/0x684
__primary_switched+0xb8/0xc0
Code: 9100a273 35000d01 53067f00 d0016dc1 (f8607a60)
---[ end trace 0000000000000000 ]---
Kernel panic - not syncing: Attempted to kill the idle task!
---[ end Kernel panic - not syncing: Attempted to kill the idle task! ]---
Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reported-by: Nathan Chancellor <nathan@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Link: http://lkml.kernel.org/r/91eacde0-df99-4d5c-a980-91046f66e612@samsung.com
Fixes: 5797b1c189 ("workqueue: Implement system-wide nr_active enforcement for unbound workqueues")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5797b1c189 ]
A pool_workqueue (pwq) represents the connection between a workqueue and a
worker_pool. One of the roles that a pwq plays is enforcement of the
max_active concurrency limit. Before 636b927eba ("workqueue: Make unbound
workqueues to use per-cpu pool_workqueues"), there was one pwq per each CPU
for per-cpu workqueues and per each NUMA node for unbound workqueues, which
was a natural result of per-cpu workqueues being served by per-cpu pools and
unbound by per-NUMA pools.
In terms of max_active enforcement, this was, while not perfect, workable.
For per-cpu workqueues, it was fine. For unbound, it wasn't great in that
NUMA machines would get max_active that's multiplied by the number of nodes
but didn't cause huge problems because NUMA machines are relatively rare and
the node count is usually pretty low.
However, cache layouts are more complex now and sharing a worker pool across
a whole node didn't really work well for unbound workqueues. Thus, a series
of commits culminating on 8639ecebc9 ("workqueue: Make unbound workqueues
to use per-cpu pool_workqueues") implemented more flexible affinity
mechanism for unbound workqueues which enables using e.g. last-level-cache
aligned pools. In the process, 636b927eba ("workqueue: Make unbound
workqueues to use per-cpu pool_workqueues") made unbound workqueues use
per-cpu pwqs like per-cpu workqueues.
While the change was necessary to enable more flexible affinity scopes, this
came with the side effect of blowing up the effective max_active for unbound
workqueues. Before, the effective max_active for unbound workqueues was
multiplied by the number of nodes. After, by the number of CPUs.
636b927eba ("workqueue: Make unbound workqueues to use per-cpu
pool_workqueues") claims that this should generally be okay. It is okay for
users which self-regulates concurrency level which are the vast majority;
however, there are enough use cases which actually depend on max_active to
prevent the level of concurrency from going bonkers including several IO
handling workqueues that can issue a work item for each in-flight IO. With
targeted benchmarks, the misbehavior can easily be exposed as reported in
http://lkml.kernel.org/r/dbu6wiwu3sdhmhikb2w6lns7b27gbobfavhjj57kwi2quafgwl@htjcc5oikcr3.
Unfortunately, there is no way to express what these use cases need using
per-cpu max_active. A CPU may issue most of in-flight IOs, so we don't want
to set max_active too low but as soon as we increase max_active a bit, we
can end up with unreasonable number of in-flight work items when many CPUs
issue IOs at the same time. ie. The acceptable lowest max_active is higher
than the acceptable highest max_active.
Ideally, max_active for an unbound workqueue should be system-wide so that
the users can regulate the total level of concurrency regardless of node and
cache layout. The reasons workqueue hasn't implemented that yet are:
- One max_active enforcement decouples from pool boundaires, chaining
execution after a work item finishes requires inter-pool operations which
would require lock dancing, which is nasty.
- Sharing a single nr_active count across the whole system can be pretty
expensive on NUMA machines.
- Per-pwq enforcement had been more or less okay while we were using
per-node pools.
It looks like we no longer can avoid decoupling max_active enforcement from
pool boundaries. This patch implements system-wide nr_active mechanism with
the following design characteristics:
- To avoid sharing a single counter across multiple nodes, the configured
max_active is split across nodes according to the proportion of each
workqueue's online effective CPUs per node. e.g. A node with twice more
online effective CPUs will get twice higher portion of max_active.
- Workqueue used to be able to process a chain of interdependent work items
which is as long as max_active. We can't do this anymore as max_active is
distributed across the nodes. Instead, a new parameter min_active is
introduced which determines the minimum level of concurrency within a node
regardless of how max_active distribution comes out to be.
It is set to the smaller of max_active and WQ_DFL_MIN_ACTIVE which is 8.
This can lead to higher effective max_weight than configured and also
deadlocks if a workqueue was depending on being able to handle chains of
interdependent work items that are longer than 8.
I believe these should be fine given that the number of CPUs in each NUMA
node is usually higher than 8 and work item chain longer than 8 is pretty
unlikely. However, if these assumptions turn out to be wrong, we'll need
to add an interface to adjust min_active.
- Each unbound wq has an array of struct wq_node_nr_active which tracks
per-node nr_active. When its pwq wants to run a work item, it has to
obtain the matching node's nr_active. If over the node's max_active, the
pwq is queued on wq_node_nr_active->pending_pwqs. As work items finish,
the completion path round-robins the pending pwqs activating the first
inactive work item of each, which involves some pool lock dancing and
kicking other pools. It's not the simplest code but doesn't look too bad.
v4: - wq_adjust_max_active() updated to invoke wq_update_node_max_active().
- wq_adjust_max_active() is now protected by wq->mutex instead of
wq_pool_mutex.
v3: - wq_node_max_active() used to calculate per-node max_active on the fly
based on system-wide CPU online states. Lai pointed out that this can
lead to skewed distributions for workqueues with restricted cpumasks.
Update the max_active distribution to use per-workqueue effective
online CPU counts instead of system-wide and cache the calculation
results in node_nr_active->max.
v2: - wq->min/max_active now uses WRITE/READ_ONCE() as suggested by Lai.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Naohiro Aota <Naohiro.Aota@wdc.com>
Link: http://lkml.kernel.org/r/dbu6wiwu3sdhmhikb2w6lns7b27gbobfavhjj57kwi2quafgwl@htjcc5oikcr3
Fixes: 636b927eba ("workqueue: Make unbound workqueues to use per-cpu pool_workqueues")
Reviewed-by: Lai Jiangshan <jiangshanlai@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91ccc6e723 ]
Currently, for both percpu and unbound workqueues, max_active applies
per-cpu, which is a recent change for unbound workqueues. The change for
unbound workqueues was a significant departure from the previous behavior of
per-node application. It made some use cases create undesirable number of
concurrent work items and left no good way of fixing them. To address the
problem, workqueue is implementing a NUMA node segmented global nr_active
mechanism, which will be explained further in the next patch.
As a preparation, this patch introduces struct wq_node_nr_active. It's a
data structured allocated for each workqueue and NUMA node pair and
currently only tracks the workqueue's number of active work items on the
node. This is split out from the next patch to make it easier to understand
and review.
Note that there is an extra wq_node_nr_active allocated for the invalid node
nr_node_ids which is used to track nr_active for pools which don't have NUMA
node associated such as the default fallback system-wide pool.
This doesn't cause any behavior changes visible to userland yet. The next
patch will expand to implement the control mechanism on top.
v4: - Fixed out-of-bound access when freeing per-cpu workqueues.
v3: - Use flexible array for wq->node_nr_active as suggested by Lai.
v2: - wq->max_active now uses WRITE/READ_ONCE() as suggested by Lai.
- Lai pointed out that pwq_tryinc_nr_active() incorrectly dropped
pwq->max_active check. Restored. As the next patch replaces the
max_active enforcement mechanism, this doesn't change the end result.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Lai Jiangshan <jiangshanlai@gmail.com>
Stable-dep-of: 5797b1c189 ("workqueue: Implement system-wide nr_active enforcement for unbound workqueues")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f66cff212 ]
wq->cpu_pwq is RCU protected but wq->dfl_pwq isn't. This is okay because
currently wq->dfl_pwq is used only accessed to install it into wq->cpu_pwq
which doesn't require RCU access. However, we want to be able to access
wq->dfl_pwq under RCU in the future to access its __pod_cpumask and the code
can be made easier to read by making the two pwq fields behave in the same
way.
- Make wq->dfl_pwq RCU protected.
- Add unbound_pwq_slot() and unbound_pwq() which can access both ->dfl_pwq
and ->cpu_pwq. The former returns the double pointer that can be used
access and update the pwqs. The latter performs locking check and
dereferences the double pointer.
- pwq accesses and updates are converted to use unbound_pwq[_slot]().
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Lai Jiangshan <jiangshanlai@gmail.com>
Stable-dep-of: 5797b1c189 ("workqueue: Implement system-wide nr_active enforcement for unbound workqueues")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c5404d4e6d ]
wq_adjust_max_active() needs to activate work items after max_active is
increased. Previously, it did that by visiting each pwq once activating all
that could be activated. While this makes sense with per-pwq nr_active,
nr_active will be shared across multiple pwqs for unbound wqs. Then, we'd
want to round-robin through pwqs to be fairer.
In preparation, this patch makes wq_adjust_max_active() round-robin pwqs
while activating. While the activation ordering changes, this shouldn't
cause user-noticeable behavior changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Lai Jiangshan <jiangshanlai@gmail.com>
Stable-dep-of: 5797b1c189 ("workqueue: Implement system-wide nr_active enforcement for unbound workqueues")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c270b79ce ]
__queue_work(), pwq_dec_nr_in_flight() and wq_adjust_max_active() were
open-coding nr_active handling, which is fine given that the operations are
trivial. However, the planned unbound nr_active update will make them more
complicated, so let's move them into helpers.
- pwq_tryinc_nr_active() is added. It increments nr_active if under
max_active limit and return a boolean indicating whether inc was
successful. Note that the function is structured to accommodate future
changes. __queue_work() is updated to use the new helper.
- pwq_activate_first_inactive() is updated to use pwq_tryinc_nr_active() and
thus no longer assumes that nr_active is under max_active and returns a
boolean to indicate whether a work item has been activated.
- wq_adjust_max_active() no longer tests directly whether a work item can be
activated. Instead, it's updated to use the return value of
pwq_activate_first_inactive() to tell whether a work item has been
activated.
- nr_active decrement and activating the first inactive work item is
factored into pwq_dec_nr_active().
v3: - WARN_ON_ONCE(!WORK_STRUCT_INACTIVE) added to __pwq_activate_work() as
now we're calling the function unconditionally from
pwq_activate_first_inactive().
v2: - wq->max_active now uses WRITE/READ_ONCE() as suggested by Lai.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Lai Jiangshan <jiangshanlai@gmail.com>
Stable-dep-of: 5797b1c189 ("workqueue: Implement system-wide nr_active enforcement for unbound workqueues")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4c6380305d ]
To prepare for unbound nr_active handling improvements, move work activation
part of pwq_activate_inactive_work() into __pwq_activate_work() and add
pwq_activate_work() which tests WORK_STRUCT_INACTIVE and updates nr_active.
pwq_activate_first_inactive() and try_to_grab_pending() are updated to use
pwq_activate_work(). The latter conversion is functionally identical. For
the former, this conversion adds an unnecessary WORK_STRUCT_INACTIVE
testing. This is temporary and will be removed by the next patch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Lai Jiangshan <jiangshanlai@gmail.com>
Stable-dep-of: 5797b1c189 ("workqueue: Implement system-wide nr_active enforcement for unbound workqueues")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a045a272d8 ]
max_active is a workqueue-wide setting and the configured value is stored in
wq->saved_max_active; however, the effective value was stored in
pwq->max_active. While this is harmless, it makes max_active update process
more complicated and gets in the way of the planned max_active semantic
updates for unbound workqueues.
This patches moves pwq->max_active to wq->max_active. This simplifies the
code and makes freezing and noop max_active updates cheaper too. No
user-visible behavior change is intended.
As wq->max_active is updated while holding wq mutex but read without any
locking, it now uses WRITE/READ_ONCE(). A new locking locking rule WO is
added for it.
v2: wq->max_active now uses WRITE/READ_ONCE() as suggested by Lai.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Lai Jiangshan <jiangshanlai@gmail.com>
Stable-dep-of: 5797b1c189 ("workqueue: Implement system-wide nr_active enforcement for unbound workqueues")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 31c8900728 ]
Currently we limit the size of the workqueue name to 24 characters due to
commit ecf6881ff3 ("workqueue: make workqueue->name[] fixed len")
Increase the size to 32 characters and print a warning in the event
the requested name is larger than the limit of 32 characters.
Signed-off-by: Audra Mitchell <audra@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Stable-dep-of: 5797b1c189 ("workqueue: Implement system-wide nr_active enforcement for unbound workqueues")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8688ab2170 ]
In packet offload, packets are not encrypted in XFRM stack, so
the next network layer which the packets will be forwarded to
should depend on where the packet came from (either xfrm4_output
or xfrm6_output) rather than the matched SA's family type.
Test: verified IPv6-in-IPv4 packets on Android device with
IPsec packet offload enabled
Signed-off-by: Mike Yu <yumike@google.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d4872d70fc ]
In current code, xfrm_bundle_create() always uses the matched
SA's family type to look up a xfrm child route for the skb.
The route returned by xfrm_dst_lookup() will eventually be
used in xfrm_output_resume() (skb_dst(skb)->ops->local_out()).
If packet offload is used, the above behavior can lead to
calling ip_local_out() for an IPv6 packet or calling
ip6_local_out() for an IPv4 packet, which is likely to fail.
This change fixes the behavior by checking if the matched SA
has packet offload enabled. If not, keep the same behavior;
if yes, use the matched SP's family type for the lookup.
Test: verified IPv6-in-IPv4 packets on Android device with
IPsec packet offload enabled
Signed-off-by: Mike Yu <yumike@google.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d0b06dc48f ]
When resetting the bus after a gap count error, use a long rather than
short bus reset.
IEEE 1394-1995 uses only long bus resets. IEEE 1394a adds the option of
short bus resets. When video or audio transmission is in progress and a
device is hot-plugged elsewhere on the bus, the resulting bus reset can
cause video frame drops or audio dropouts. Short bus resets reduce or
eliminate this problem. Accordingly, short bus resets are almost always
preferred.
However, on a mixed 1394/1394a bus, a short bus reset can trigger an
immediate additional bus reset. This double bus reset can be interpreted
differently by different nodes on the bus, resulting in an inconsistent gap
count after the bus reset. An inconsistent gap count will cause another bus
reset, leading to a neverending bus reset loop. This only happens for some
bus topologies, not for all mixed 1394/1394a buses.
By instead sending a long bus reset after a gap count inconsistency, we
avoid the doubled bus reset, restoring the bus to normal operation.
Signed-off-by: Adam Goldman <adamg@pobox.com>
Link: https://sourceforge.net/p/linux1394/mailman/message/58741624/
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0bd1fb5862 ]
LIMITED_DISCOVERABLE flag is not reset from Class of Device and
advertisement on limited discoverable timeout. This prevents to pass PTS
test GAP/DISC/LIMM/BV-02-C
Calling set_discoverable_sync as when the limited discovery is set
correctly update the Class of Device and advertisement.
Signed-off-by: Frédéric Danis <frederic.danis@collabora.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2535b848fa ]
During our fuzz testing of the connection and disconnection process at the
RFCOMM layer, we discovered this bug. By comparing the packets from a
normal connection and disconnection process with the testcase that
triggered a KASAN report. We analyzed the cause of this bug as follows:
1. In the packets captured during a normal connection, the host sends a
`Read Encryption Key Size` type of `HCI_CMD` packet
(Command Opcode: 0x1408) to the controller to inquire the length of
encryption key.After receiving this packet, the controller immediately
replies with a Command Completepacket (Event Code: 0x0e) to return the
Encryption Key Size.
2. In our fuzz test case, the timing of the controller's response to this
packet was delayed to an unexpected point: after the RFCOMM and L2CAP
layers had disconnected but before the HCI layer had disconnected.
3. After receiving the Encryption Key Size Response at the time described
in point 2, the host still called the rfcomm_check_security function.
However, by this time `struct l2cap_conn *conn = l2cap_pi(sk)->chan->conn;`
had already been released, and when the function executed
`return hci_conn_security(conn->hcon, d->sec_level, auth_type, d->out);`,
specifically when accessing `conn->hcon`, a null-ptr-deref error occurred.
To fix this bug, check if `sk->sk_state` is BT_CLOSED before calling
rfcomm_recv_frame in rfcomm_process_rx.
Signed-off-by: Yuxuan Hu <20373622@buaa.edu.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c671ec0131 ]
Currently, GPU resets can now be performed successfully on the Raven
series. While GPU reset is required for the S3 suspend abort case.
So now can enable gpu reset for S3 abort cases on the Raven series.
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee0017c3ed ]
If the driver detects that the controller is not ready before sending the
first IOC facts command, it will wait for a maximum of 10 seconds for it to
become ready. However, even if the controller becomes ready within 10
seconds, the driver will still issue a diagnostic reset.
Modify the driver to avoid sending a diag reset if the controller becomes
ready within the 10-second wait time.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20240221071724.14986-1-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 413dafc817 ]
When a station has not been uploaded yet, receiving SMPS or channel width
notification action frames can lead to rate_control_rate_update calling
drv_sta_rc_update with uninitialized driver private data.
Fix this by adding a missing check for sta->uploaded.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://msgid.link/20240221140535.16102-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7bb26b847 ]
At btrfs_use_block_rsv() we read the size of a block reserve without
locking its spinlock, which makes KCSAN complain because the size of a
block reserve is always updated while holding its spinlock. The report
from KCSAN is the following:
[653.313148] BUG: KCSAN: data-race in btrfs_update_delayed_refs_rsv [btrfs] / btrfs_use_block_rsv [btrfs]
[653.314755] read to 0x000000017f5871b8 of 8 bytes by task 7519 on cpu 0:
[653.314779] btrfs_use_block_rsv+0xe4/0x2f8 [btrfs]
[653.315606] btrfs_alloc_tree_block+0xdc/0x998 [btrfs]
[653.316421] btrfs_force_cow_block+0x220/0xe38 [btrfs]
[653.317242] btrfs_cow_block+0x1ac/0x568 [btrfs]
[653.318060] btrfs_search_slot+0xda2/0x19b8 [btrfs]
[653.318879] btrfs_del_csums+0x1dc/0x798 [btrfs]
[653.319702] __btrfs_free_extent.isra.0+0xc24/0x2028 [btrfs]
[653.320538] __btrfs_run_delayed_refs+0xd3c/0x2390 [btrfs]
[653.321340] btrfs_run_delayed_refs+0xae/0x290 [btrfs]
[653.322140] flush_space+0x5e4/0x718 [btrfs]
[653.322958] btrfs_preempt_reclaim_metadata_space+0x102/0x2f8 [btrfs]
[653.323781] process_one_work+0x3b6/0x838
[653.323800] worker_thread+0x75e/0xb10
[653.323817] kthread+0x21a/0x230
[653.323836] __ret_from_fork+0x6c/0xb8
[653.323855] ret_from_fork+0xa/0x30
[653.323887] write to 0x000000017f5871b8 of 8 bytes by task 576 on cpu 3:
[653.323906] btrfs_update_delayed_refs_rsv+0x1a4/0x250 [btrfs]
[653.324699] btrfs_add_delayed_data_ref+0x468/0x6d8 [btrfs]
[653.325494] btrfs_free_extent+0x76/0x120 [btrfs]
[653.326280] __btrfs_mod_ref+0x6a8/0x6b8 [btrfs]
[653.327064] btrfs_dec_ref+0x50/0x70 [btrfs]
[653.327849] walk_up_proc+0x236/0xa50 [btrfs]
[653.328633] walk_up_tree+0x21c/0x448 [btrfs]
[653.329418] btrfs_drop_snapshot+0x802/0x1328 [btrfs]
[653.330205] btrfs_clean_one_deleted_snapshot+0x184/0x238 [btrfs]
[653.330995] cleaner_kthread+0x2b0/0x2f0 [btrfs]
[653.331781] kthread+0x21a/0x230
[653.331800] __ret_from_fork+0x6c/0xb8
[653.331818] ret_from_fork+0xa/0x30
So add a helper to get the size of a block reserve while holding the lock.
Reading the field while holding the lock instead of using the data_race()
annotation is used in order to prevent load tearing.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e06cc89475 ]
At space_info.c we have several places where we access the ->reserved
field of a block reserve without taking the block reserve's spinlock
first, which makes KCSAN warn about a data race since that field is
always updated while holding the spinlock.
The reports from KCSAN are like the following:
[117.193526] BUG: KCSAN: data-race in btrfs_block_rsv_release [btrfs] / need_preemptive_reclaim [btrfs]
[117.195148] read to 0x000000017f587190 of 8 bytes by task 6303 on cpu 3:
[117.195172] need_preemptive_reclaim+0x222/0x2f0 [btrfs]
[117.195992] __reserve_bytes+0xbb0/0xdc8 [btrfs]
[117.196807] btrfs_reserve_metadata_bytes+0x4c/0x120 [btrfs]
[117.197620] btrfs_block_rsv_add+0x78/0xa8 [btrfs]
[117.198434] btrfs_delayed_update_inode+0x154/0x368 [btrfs]
[117.199300] btrfs_update_inode+0x108/0x1c8 [btrfs]
[117.200122] btrfs_dirty_inode+0xb4/0x140 [btrfs]
[117.200937] btrfs_update_time+0x8c/0xb0 [btrfs]
[117.201754] touch_atime+0x16c/0x1e0
[117.201789] filemap_read+0x674/0x728
[117.201823] btrfs_file_read_iter+0xf8/0x410 [btrfs]
[117.202653] vfs_read+0x2b6/0x498
[117.203454] ksys_read+0xa2/0x150
[117.203473] __s390x_sys_read+0x68/0x88
[117.203495] do_syscall+0x1c6/0x210
[117.203517] __do_syscall+0xc8/0xf0
[117.203539] system_call+0x70/0x98
[117.203579] write to 0x000000017f587190 of 8 bytes by task 11 on cpu 0:
[117.203604] btrfs_block_rsv_release+0x2e8/0x578 [btrfs]
[117.204432] btrfs_delayed_inode_release_metadata+0x7c/0x1d0 [btrfs]
[117.205259] __btrfs_update_delayed_inode+0x37c/0x5e0 [btrfs]
[117.206093] btrfs_async_run_delayed_root+0x356/0x498 [btrfs]
[117.206917] btrfs_work_helper+0x160/0x7a0 [btrfs]
[117.207738] process_one_work+0x3b6/0x838
[117.207768] worker_thread+0x75e/0xb10
[117.207797] kthread+0x21a/0x230
[117.207830] __ret_from_fork+0x6c/0xb8
[117.207861] ret_from_fork+0xa/0x30
So add a helper to get the reserved amount of a block reserve while
holding the lock. The value may be not be up to date anymore when used by
need_preemptive_reclaim() and btrfs_preempt_reclaim_metadata_space(), but
that's ok since the worst it can do is cause more reclaim work do be done
sooner rather than later. Reading the field while holding the lock instead
of using the data_race() annotation is used in order to prevent load
tearing.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 787f1b2800 ]
"struct bvec_iter" is defined with the __packed attribute, so it is
aligned on a single byte. On X86 (and on other architectures that support
unaligned addresses in hardware), "struct bvec_iter" is accessed using the
8-byte and 4-byte memory instructions, however these instructions are less
efficient if they operate on unaligned addresses.
(on RISC machines that don't have unaligned access in hardware, GCC
generates byte-by-byte accesses that are very inefficient - see [1])
This commit reorders the entries in "struct dm_verity_io" and "struct
convert_context", so that "struct bvec_iter" is aligned on 8 bytes.
[1] https://lore.kernel.org/all/ZcLuWUNRZadJr0tQ@fedora/T/
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb66b1d60c ]
Autodiscovered regions can fail to assemble if they are not discovered
in HPA decode order. The user will see failure messages like:
[] cxl region0: endpoint5: HPA order violation region1
[] cxl region0: endpoint5: failed to allocate region reference
The check that is causing the failure helps the CXL driver enforce
a CXL spec mandate that decoders be committed in HPA order. The
check is needless for autodiscovered regions since their decoders
are already programmed. Trying to enforce order in the assembly of
these regions is useless because they are assembled once all their
member endpoints arrive, and there is no guarantee on the order in
which endpoints are discovered during probe.
Keep the existing check, but for autodiscovered regions, allow the
out of order assembly after a sanity check that the lesser numbered
decoder has the lesser HPA starting address.
Signed-off-by: Alison Schofield <alison.schofield@intel.com>
Tested-by: Wonjae Lee <wj28.lee@samsung.com>
Link: https://lore.kernel.org/r/3dec69ee97524ab229a20c6739272c3000b18408.1706736863.git.alison.schofield@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 250f5402e6 ]
Fixes a bug revealed by -Wmissing-prototypes when
CONFIG_FUNCTION_GRAPH_TRACER is enabled but not CONFIG_DYNAMIC_FTRACE:
arch/parisc/kernel/ftrace.c:82:5: error: no previous prototype for 'ftrace_enable_ftrace_graph_caller' [-Werror=missing-prototypes]
82 | int ftrace_enable_ftrace_graph_caller(void)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
arch/parisc/kernel/ftrace.c:88:5: error: no previous prototype for 'ftrace_disable_ftrace_graph_caller' [-Werror=missing-prototypes]
88 | int ftrace_disable_ftrace_graph_caller(void)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Max Kellermann <max.kellermann@ionos.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b4ea9b6a18 ]
iucv_path_table is a dynamically allocated array of pointers to
struct iucv_path items. Yet, its size is calculated as if it was
an array of struct iucv_path items.
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 32019c659e ]
When trying to use copy_from_kernel_nofault() to read vsyscall page
through a bpf program, the following oops was reported:
BUG: unable to handle page fault for address: ffffffffff600000
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 3231067 P4D 3231067 PUD 3233067 PMD 3235067 PTE 0
Oops: 0000 [#1] PREEMPT SMP PTI
CPU: 1 PID: 20390 Comm: test_progs ...... 6.7.0+ #58
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996) ......
RIP: 0010:copy_from_kernel_nofault+0x6f/0x110
......
Call Trace:
<TASK>
? copy_from_kernel_nofault+0x6f/0x110
bpf_probe_read_kernel+0x1d/0x50
bpf_prog_2061065e56845f08_do_probe_read+0x51/0x8d
trace_call_bpf+0xc5/0x1c0
perf_call_bpf_enter.isra.0+0x69/0xb0
perf_syscall_enter+0x13e/0x200
syscall_trace_enter+0x188/0x1c0
do_syscall_64+0xb5/0xe0
entry_SYSCALL_64_after_hwframe+0x6e/0x76
</TASK>
......
---[ end trace 0000000000000000 ]---
The oops is triggered when:
1) A bpf program uses bpf_probe_read_kernel() to read from the vsyscall
page and invokes copy_from_kernel_nofault() which in turn calls
__get_user_asm().
2) Because the vsyscall page address is not readable from kernel space,
a page fault exception is triggered accordingly.
3) handle_page_fault() considers the vsyscall page address as a user
space address instead of a kernel space address. This results in the
fix-up setup by bpf not being applied and a page_fault_oops() is invoked
due to SMAP.
Considering handle_page_fault() has already considered the vsyscall page
address as a userspace address, fix the problem by disallowing vsyscall
page read for copy_from_kernel_nofault().
Originally-by: Thomas Gleixner <tglx@linutronix.de>
Reported-by: syzbot+72aa0161922eba61b50e@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/bpf/CAG48ez06TZft=ATH1qh2c5mpS5BT8UakwNkzi6nvK5_djC-4Nw@mail.gmail.com
Reported-by: xingwei lee <xrivendell7@gmail.com>
Closes: https://lore.kernel.org/bpf/CABOYnLynjBoFZOf3Z4BhaZkc5hx_kHfsjiW+UWLoB=w33LvScw@mail.gmail.com
Signed-off-by: Hou Tao <houtao1@huawei.com>
Reviewed-by: Sohil Mehta <sohil.mehta@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240202103935.3154011-3-houtao@huaweicloud.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be551ee157 ]
Relax DEVX access upon modify commands to be UVERBS_ACCESS_READ.
The kernel doesn't need to protect what firmware protects, or what
causes no damage to anyone but the user.
As firmware needs to protect itself from parallel access to the same
object, don't block parallel modify/query commands on the same object in
the kernel side.
This change will allow user space application to run parallel updates to
different entries in the same bulk object.
Tested-by: Tamar Mashiah <tmashiah@nvidia.com>
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Reviewed-by: Michael Guralnik <michaelgur@nvidia.com>
Link: https://lore.kernel.org/r/7407d5ed35dc427c1097699e12b49c01e1073406.1706433934.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2813926261 ]
Doug Anderson observed that ChromeOS crashes are being reported which
include failing allocations of order 7 during core dumps due to ptrace
allocating storage for regsets:
chrome: page allocation failure: order:7,
mode:0x40dc0(GFP_KERNEL|__GFP_COMP|__GFP_ZERO),
nodemask=(null),cpuset=urgent,mems_allowed=0
...
regset_get_alloc+0x1c/0x28
elf_core_dump+0x3d8/0xd8c
do_coredump+0xeb8/0x1378
with further investigation showing that this is:
[ 66.957385] DOUG: Allocating 279584 bytes
which is the maximum size of the SVE regset. As Doug observes it is not
entirely surprising that such a large allocation of contiguous memory might
fail on a long running system.
The SVE regset is currently sized to hold SVE registers with a VQ of
SVE_VQ_MAX which is 512, substantially more than the architectural maximum
of 16 which we might see even in a system emulating the limits of the
architecture. Since we don't expose the size we tell the regset core
externally let's define ARCH_SVE_VQ_MAX with the actual architectural
maximum and use that for the regset, we'll still overallocate most of the
time but much less so which will be helpful even if the core is fixed to
not require contiguous allocations.
Specify ARCH_SVE_VQ_MAX in terms of the maximum value that can be written
into ZCR_ELx.LEN (where this is set in the hardware). For consistency
update the maximum SME vector length to be specified in the same style
while we are at it.
We could also teach the ptrace core about runtime discoverable regset sizes
but that would be a more invasive change and this is being observed in
practical systems.
Reported-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20240213-arm64-sve-ptrace-regset-size-v2-1-c7600ca74b9b@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c40aad7c81 ]
When the system is suspended while audio is active, the
sof_ipc4_pcm_hw_free() is invoked to reset the pipelines since during
suspend the DSP is turned off, streams will be re-started after resume.
If the firmware crashes during while audio is running (or when we reset
the stream before suspend) then the sof_ipc4_set_multi_pipeline_state()
will fail with IPC error and the state change is interrupted.
This will cause misalignment between the kernel and firmware state on next
DSP boot resulting errors returned by firmware for IPC messages, eventually
failing the audio resume.
On stream close the errors are ignored so the kernel state will be
corrected on the next DSP boot, so the second boot after the DSP panic.
If sof_ipc4_trigger_pipelines() is called from sof_ipc4_pcm_hw_free() then
state parameter is SOF_IPC4_PIPE_RESET and only in this case.
Treat a forced pipeline reset similarly to how we treat a pcm_free by
ignoring error on state sending to allow the kernel's state to be
consistent with the state the firmware will have after the next boot.
Link: https://github.com/thesofproject/sof/issues/8721
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://msgid.link/r/20240213115233.15716-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d6e21ddf2 ]
Clear Cause.BD after we use instruction_pointer_set to override
EPC.
This can prevent exception_epc check against instruction code at
new return address.
It won't be considered as "in delay slot" after epc being overridden
anyway.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f0dbb24f7 ]
During the cache sync test we verify that values we expect to have been
written only to the cache do not appear in the hardware. This works most
of the time but since we randomly generate both the original and new values
there is a low probability that these values may actually be the same.
Wrap get_random_bytes() to ensure that the values are different, there
are other tests which should have similar verification that we actually
changed something.
While we're at it refactor the test to use three changed values rather
than attempting to use one of them twice, that just complicates checking
that our new values are actually new.
We use random generation to try to avoid data dependencies in the tests.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://msgid.link/r/20240211-regmap-kunit-random-change-v3-1-e387a9ea4468@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e57b77583 ]
As described in IEEE sta 802.11-2020, table 9-30 (Address
field contents), A-MSDU address 3 should contain the BSSID
address.
In TX_CMD we copy the MAC header from skb, and skb address 3
holds the destination address, but it may not be identical to
the BSSID.
Using the wrong destination address appears to work with (most)
receivers without MLO, but in MLO some devices are checking for
it carefully, perhaps as a consequence of link to MLD address
translation.
Replace address 3 in the TX_CMD MAC header with the correct
address while retaining the skb address 3 unchanged.
This ensures that skb address 3 will be utilized later for
constructing the A-MSDU subframes.
Note that we fill in the MLD address, but the firmware will do the
necessary translation to link address after encryption.
Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240204235836.4583a1bf9188.I3f8e7892bdf8f86b4daa28453771a8c9817b2416@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ffb635bb39 ]
The driver requests the interrupts as IRQF_SHARED, so the interrupt
handlers can be called at any time. If such a call happens while the ISP
is powered down, the SoC will hang as the driver tries to access the
ISP registers.
This can be reproduced even without the platform sharing the IRQ line:
Enable CONFIG_DEBUG_SHIRQ and unload the driver, and the board will
hang.
Fix this by adding a new field, 'irqs_enabled', which is used to bail
out from the interrupt handler when the ISP is not operational.
Link: https://lore.kernel.org/r/20231218-rkisp-shirq-fix-v1-2-173007628248@ideasonboard.com
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b979f2d50a upstream.
A recent DRM series purporting to simplify support for "transparent
bridges" and handling of probe deferrals ironically exposed a
use-after-free issue on pmic_glink_altmode probe deferral.
This has manifested itself as the display subsystem occasionally failing
to initialise and NULL-pointer dereferences during boot of machines like
the Lenovo ThinkPad X13s.
Specifically, the dp-hpd bridge is currently registered before all
resources have been acquired which means that it can also be
deregistered on probe deferrals.
In the meantime there is a race window where the new aux bridge driver
(or PHY driver previously) may have looked up the dp-hpd bridge and
stored a (non-reference-counted) pointer to the bridge which is about to
be deallocated.
When the display controller is later initialised, this triggers a
use-after-free when attaching the bridges:
dp -> aux -> dp-hpd (freed)
which may, for example, result in the freed bridge failing to attach:
[drm:drm_bridge_attach [drm]] *ERROR* failed to attach bridge /soc@0/phy@88eb000 to encoder TMDS-31: -16
or a NULL-pointer dereference:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
...
Call trace:
drm_bridge_attach+0x70/0x1a8 [drm]
drm_aux_bridge_attach+0x24/0x38 [aux_bridge]
drm_bridge_attach+0x80/0x1a8 [drm]
dp_bridge_init+0xa8/0x15c [msm]
msm_dp_modeset_init+0x28/0xc4 [msm]
The DRM bridge implementation is clearly fragile and implicitly built on
the assumption that bridges may never go away. In this case, the fix is
to move the bridge registration in the pmic_glink_altmode driver to
after all resources have been looked up.
Incidentally, with the new dp-hpd bridge implementation, which registers
child devices, this is also a requirement due to a long-standing issue
in driver core that can otherwise lead to a probe deferral loop (see
commit fbc35b45f9 ("Add documentation on meaning of -EPROBE_DEFER")).
[DB: slightly fixed commit message by adding the word 'commit']
Fixes: 080b4e2485 ("soc: qcom: pmic_glink: Introduce altmode support")
Fixes: 2bcca96abf ("soc: qcom: pmic-glink: switch to DRM_AUX_HPD_BRIDGE")
Cc: <stable@vger.kernel.org> # 6.3
Cc: Bjorn Andersson <andersson@kernel.org>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240217150228.5788-4-johan+linaro@kernel.org
[ johan: backport to 6.7 which does not have DRM aux bridge ]
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
This is dead code after we dropped support for passing io_uring fds
over SCM_RIGHTS, get rid of it.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit a4104821ad upstream.
Since we no longer allow sending io_uring fds over SCM_RIGHTS, move to
using io_is_uring_fops() to detect whether this is a io_uring fd or not.
With that done, kill off io_uring_get_socket() as nobody calls it
anymore.
This is in preparation to yanking out the rest of the core related to
unix gc with io_uring.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aec7d25b49 ]
On Goldmont p2sb_bar() only ever gets called for 2 devices, the actual P2SB
devfn 13,0 and the SPI controller which is part of the P2SB, devfn 13,2.
But the current p2sb code tries to cache BAR0 info for all of
devfn 13,0 to 13,7 . This involves calling pci_scan_single_device()
for device 13 functions 0-7 and the hw does not seem to like
pci_scan_single_device() getting called for some of the other hidden
devices. E.g. on an ASUS VivoBook D540NV-GQ065T this leads to continuous
ACPI errors leading to high CPU usage.
Fix this by only caching BAR0 info and thus only calling
pci_scan_single_device() for the P2SB and the SPI controller.
Fixes: 5913320eb0 ("platform/x86: p2sb: Allow p2sb_bar() calls during PCI device probe")
Reported-by: Danil Rybakov <danilrybakov249@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218531
Tested-by: Danil Rybakov <danilrybakov249@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240304134356.305375-2-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Since I noticed that sometimes changing sample rates causes some digital
quirks and noises, I've changed the function to mute the output before
performing the changes and then unmute it when an error occurs or the
parameters got set.
Signed-off-by: Alessandro Marcon <marconalessandro04@gmail.com>
The RPi5 firmware also supports exporting the customer
public key stored in flash via device-tree. Define the
node so that the firmware can populate it.
Signed-off-by: Tim Gover <tim.gover@raspberrypi.com>
The default was to have enable_bg_fill disabled and the first
plane set it if it wasn't opaque and covering the whole screen.
However that meant that if no planes were enabled, then the
background fill wasn't enabled, and would give a striped
output from the uninitialised output buffer.
Initialise it to enabled to avoid this.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
For unknown reasons the controller seems to reset the idle polling timer
interval on CQE enable/disable to 8 clocks which is extremely short.
Just use the reset value in the eMMC spec (4096 clock periods which at
200MHz is ~20uS).
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Command Queueing on Linux with SD cards is new, with the potential to cause
filesystem corruption due to bugs in software or card firmware(s).
Default to disabled unless a) we know the interface connects to an eMMC
device or b) we want it switched on.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Add a LED_FULL trigger equivalent to mmc_start_request() in
mmc_cqe_start_req(), otherwise it stays off forever.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
The Performance Extension register is regularly accessed in a hot path
to do write cache flushes. Don't invoke kmalloc/kfree for every access,
preallocate a 512B buffer for this purpose.
Also remove an unused alloc in sd_enable_cache().
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
CQHCI keeps track of tags in flight with internal timers, so the clock
frequency driving the timer needs to be specified. The config registers
default to 0 (100kHz) which means timeouts will be significantly shorter
than they should be. Assume the timer clock comes from the controller
base clock.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Application class A2 cards require CQ to be enabled to realise their
stated performance figures. Add support to enable/disable card CQ via
the Performance Enhancement extension register, and cater for the slight
differences in command set versus eMMC.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Make i2c_csi_dsi an alias for i2c_csi_dsi1, and remove the spurious
redefinition in the cm5 .dts files.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The upstream Pi DTS files select serial1 for stdout-path, but because of
the way the downstream kernel numbers UARTS, serial0 is required in the
downstream DTS. Using the wrong value breaks U-boot.
In the 6.6 kernel the downstream Pi 400 DTS was made closer to upstream,
inheriting most of its content from the Pi 4B DTS, but because of the
order of inclusion it lost the override for stdout-path. Restore that
override.
See: https://github.com/raspberrypi/firmware/issues/1875
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
As we have never released a (standard) DACplusADC board with onboard
clocks, we can simply use a fixed setup avoiding incompatibilities
with Pi5 during driver init. Setting 'hifiberry-dacplusadc,slave' in
the overlays disables the failing clock probing mechanism.
Removes 'slave' parameter description from README which is still
supported but not needed.
Signed-off-by: j-schambacher <joerg@hifiberry.com>
As the easy switching of the I2S module bewteen clock producer/consumer
on the PI5 is not possible, two specific DT-overlays are introduced.
The DAC+PRO boards with onboard clocks use the -PRO overlay, the boards
without oscillators the -STD version.
The "hifiberry-dacplus,slave" parameter in the -STD overlay disables
the automatic clock detection inside the hifiberry-dacplus driver.
The former hifiberry-dacplus overlay is kept for compatibility but
will be deprecated.
Signed-off-by: j-schambacher <joerg@hifiberry.com>
The /soc/sound node is not a feature of the bcm2712 hardware, rather a
Raspberry Pi convention of where to declare soundcards. Move it to
bcm2712-rpi.dtsi accordingly, at the same time marking it as disabled
so that runtime overlay application causes the soundcard device to be
created.
See: https://forums.raspberrypi.com/viewtopic.php?t=367530
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
[1] calculates timings for arbitrary clock speeds, but it does so aiming
for a 50% SCL duty cycle. This is the wrong goal, particularly for high
clock speeds, because it doesn't allow the device sufficient time to
pull the bus low to issue an ACK.
Change the algorithm to aim for the minimum SCL high time (tHIGH) for
the requested speed according to the I2C Specification, using linear
interpolation between the values for the standard speeds.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
[1] commit cea76e589d ("i2c: designware: Support non-standard bus speeds")
Also create generic overrides in camera-mux-N-port, that can be extended
to configure vsync modes for cameras supporting this.
Example usages (to be combined with camera_auto_detect=0):
dtoverlay=imx477,cam0,sync-source
dtoverlay=imx477,sync-sink
dtoverlay=camera-mux-2port,cam1-imx477,cam1-sync-sink
dtoverlay=camera-mux-4port,cam3-imx477,cam3-sync-sink
Signed-off-by: Erik Botö <erik.boto@gmail.com>
Allow trigger-mode to be overridden using device tree so that it can be
set per camera. Previously the mode could only be changed using a module
parameter, which would then affect all cameras.
Signed-off-by: Erik Botö <erik.boto@gmail.com>
commit 2a0180129d upstream.
Mitigation for RFDS requires RFDS_CLEAR capability which is enumerated
by MSR_IA32_ARCH_CAPABILITIES bit 27. If the host has it set, export it
to guests so that they can deploy the mitigation.
RFDS_NO indicates that the system is not vulnerable to RFDS, export it
to guests so that they don't deploy the mitigation unnecessarily. When
the host is not affected by X86_BUG_RFDS, but has RFDS_NO=0, synthesize
RFDS_NO to the guest.
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8076fcde01 upstream.
RFDS is a CPU vulnerability that may allow userspace to infer kernel
stale data previously used in floating point registers, vector registers
and integer registers. RFDS only affects certain Intel Atom processors.
Intel released a microcode update that uses VERW instruction to clear
the affected CPU buffers. Unlike MDS, none of the affected cores support
SMT.
Add RFDS bug infrastructure and enable the VERW based mitigation by
default, that clears the affected buffers just before exiting to
userspace. Also add sysfs reporting and cmdline parameter
"reg_file_data_sampling" to control the mitigation.
For details see:
Documentation/admin-guide/hw-vuln/reg-file-data-sampling.rst
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e95df4ec0c upstream.
Currently MMIO Stale Data mitigation for CPUs not affected by MDS/TAA is
to only deploy VERW at VMentry by enabling mmio_stale_data_clear static
branch. No mitigation is needed for kernel->user transitions. If such
CPUs are also affected by RFDS, its mitigation may set
X86_FEATURE_CLEAR_CPU_BUF to deploy VERW at kernel->user and VMentry.
This could result in duplicate VERW at VMentry.
Fix this by disabling mmio_stale_data_clear static branch when
X86_FEATURE_CLEAR_CPU_BUF is enabled.
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ab4443fe3c ]
ra_alloc_folio() marks a page that should trigger next round of async
readahead. However it rounds up computed index to the order of page being
allocated. This can however lead to multiple consecutive pages being
marked with readahead flag. Consider situation with index == 1, mark ==
1, order == 0. We insert order 0 page at index 1 and mark it. Then we
bump order to 1, index to 2, mark (still == 1) is rounded up to 2 so page
at index 2 is marked as well. Then we bump order to 2, index is
incremented to 4, mark gets rounded to 4 so page at index 4 is marked as
well. The fact that multiple pages get marked within a single readahead
window confuses the readahead logic and results in readahead window being
trimmed back to 1. This situation is triggered in particular when maximum
readahead window size is not a power of two (in the observed case it was
768 KB) and as a result sequential read throughput suffers.
Fix the problem by rounding 'mark' down instead of up. Because the index
is naturally aligned to 'order', we are guaranteed 'rounded mark' == index
iff 'mark' is within the page we are allocating at 'index' and thus
exactly one page is marked with readahead flag as required by the
readahead code and sequential read performance is restored.
This effectively reverts part of commit b9ff43dd27 ("mm/readahead: Fix
readahead with large folios"). The commit changed the rounding with the
rationale:
"... we were setting the readahead flag on the folio which contains the
last byte read from the block. This is wrong because we will trigger
readahead at the end of the read without waiting to see if a subsequent
read is going to use the pages we just read."
Although this is true, the fact is this was always the case with read
sizes not aligned to folio boundaries and large folios in the page cache
just make the situation more obvious (and frequent). Also for sequential
read workloads it is better to trigger the readahead earlier rather than
later. It is true that the difference in the rounding and thus earlier
triggering of the readahead can result in reading more for semi-random
workloads. However workloads really suffering from this seem to be rare.
In particular I have verified that the workload described in commit
b9ff43dd27 ("mm/readahead: Fix readahead with large folios") of reading
random 100k blocks from a file like:
[reader]
bs=100k
rw=randread
numjobs=1
size=64g
runtime=60s
is not impacted by the rounding change and achieves ~70MB/s in both cases.
[jack@suse.cz: fix one more place where mark rounding was done as well]
Link: https://lkml.kernel.org/r/20240123153254.5206-1-jack@suse.cz
Link: https://lkml.kernel.org/r/20240104085839.21029-1-jack@suse.cz
Fixes: b9ff43dd27 ("mm/readahead: Fix readahead with large folios")
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Guo Xuenan <guoxuenan@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe752331d4 ]
Right now it is possible to see gmap->private being zero in
kvm_s390_vsie_gmap_notifier resulting in a crash. This is due to the
fact that we add gmap->private == kvm after creation:
static int acquire_gmap_shadow(struct kvm_vcpu *vcpu,
struct vsie_page *vsie_page)
{
[...]
gmap = gmap_shadow(vcpu->arch.gmap, asce, edat);
if (IS_ERR(gmap))
return PTR_ERR(gmap);
gmap->private = vcpu->kvm;
Let children inherit the private field of the parent.
Reported-by: Marc Hartmayer <mhartmay@linux.ibm.com>
Fixes: a3508fbe9d ("KVM: s390: vsie: initial support for nested virtualization")
Cc: <stable@vger.kernel.org>
Cc: David Hildenbrand <david@redhat.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Link: https://lore.kernel.org/r/20231220125317.4258-1-borntraeger@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3235e2dd6 ]
The shadow gmap tracks memory of nested guests (guest-3). In certain
scenarios, the shadow gmap needs to be rebuilt, which is a costly operation
since it involves a SIE exit into guest-1 for every entry in the respective
shadow level.
Add kvm stat counters when new shadow structures are created at various
levels. Also add a counter gmap_shadow_create when a completely fresh
shadow gmap is created as well as a counter gmap_shadow_reuse when an
existing gmap is being reused.
Note that when several levels are shadowed at once, counters on all
affected levels will be increased.
Also note that not all page table levels need to be present and a ASCE
can directly point to e.g. a segment table. In this case, a new segment
table will always be equivalent to a new shadow gmap and hence will be
counted as gmap_shadow_create and not as gmap_shadow_segment.
Signed-off-by: Nico Boehr <nrb@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Link: https://lore.kernel.org/r/20231009093304.2555344-2-nrb@linux.ibm.com
Message-Id: <20231009093304.2555344-2-nrb@linux.ibm.com>
Stable-dep-of: fe752331d4 ("KVM: s390: vsie: fix race during shadow creation")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d380ce7005 ]
We need to protect the reader reading the sysctl value because the
value can be changed concurrently.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc76645ebd ]
We need to protect the reader reading the sysctl value because the
value can be changed concurrently.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b5dffcb8f7 ]
We need to protect the reader reading the sysctl value because the
value can be changed concurrently.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f99b494b40 ]
We need to protect the reader reading the sysctl value because the
value can be changed concurrently.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a2e7068414 ]
We need to protect the reader reading the sysctl value because the
value can be changed concurrently.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43547d8699 ]
We need to protect the reader reading the sysctl value because the
value can be changed concurrently.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 806f462ba9 ]
We need to protect the reader reading the sysctl value because the
value can be changed concurrently.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e799299aaf ]
We need to protect the reader reading the sysctl value because the
value can be changed concurrently.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 60a7a152ab ]
We need to protect the reader reading the sysctl value because the
value can be changed concurrently.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 119cae5ea3 ]
We need to protect the reader reading the sysctl value because the
value can be changed concurrently.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cfd9f4a740 ]
We need to protect the reader reading the sysctl value
because the value can be changed concurrently.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 958d6145a6 ]
We need to protect the reader reading sysctl_netrom_default_path_quality
because the value can be changed concurrently.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4127caee89 ]
There are mainly two reasons that thp_get_unmapped_area() should be
used for EROFS as other filesystems:
- It's needed to enable PMD mappings as a FSDAX filesystem, see
commit 74d2fad133 ("thp, dax: add thp_get_unmapped_area for pmd
mappings");
- It's useful together with large folios and
CONFIG_READ_ONLY_THP_FOR_FS which enable THPs for mmapped files
(e.g. shared libraries) even without FSDAX. See commit 1854bc6e24
("mm/readahead: Align file mappings for non-DAX").
Fixes: 06252e9ce0 ("erofs: dax support for non-tailpacking regular file")
Fixes: ce529cc25b ("erofs: enable large folios for iomap mode")
Fixes: e6687b8922 ("erofs: enable large folios for fscache mode")
Reviewed-by: Jingbo Xu <jefflexu@linux.alibaba.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Link: https://lore.kernel.org/r/20240306053138.2240206-1-hsiangkao@linux.alibaba.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 767146637e ]
UBSAN load reports an exception of BRK#5515 SHIFT_ISSUE:Bitwise shifts
that are out of bounds for their data type.
vmlinux get_bitmap(b=75) + 712
<net/netfilter/nf_conntrack_h323_asn1.c:0>
vmlinux decode_seq(bs=0xFFFFFFD008037000, f=0xFFFFFFD008037018, level=134443100) + 1956
<net/netfilter/nf_conntrack_h323_asn1.c:592>
vmlinux decode_choice(base=0xFFFFFFD0080370F0, level=23843636) + 1216
<net/netfilter/nf_conntrack_h323_asn1.c:814>
vmlinux decode_seq(f=0xFFFFFFD0080371A8, level=134443500) + 812
<net/netfilter/nf_conntrack_h323_asn1.c:576>
vmlinux decode_choice(base=0xFFFFFFD008037280, level=0) + 1216
<net/netfilter/nf_conntrack_h323_asn1.c:814>
vmlinux DecodeRasMessage() + 304
<net/netfilter/nf_conntrack_h323_asn1.c:833>
vmlinux ras_help() + 684
<net/netfilter/nf_conntrack_h323_main.c:1728>
vmlinux nf_confirm() + 188
<net/netfilter/nf_conntrack_proto.c:137>
Due to abnormal data in skb->data, the extension bitmap length
exceeds 32 when decoding ras message then uses the length to make
a shift operation. It will change into negative after several loop.
UBSAN load could detect a negative shift as an undefined behaviour
and reports exception.
So we add the protection to avoid the length exceeding 32. Or else
it will return out of range error and stop decoding.
Fixes: 5e35941d99 ("[NETFILTER]: Add H.323 conntrack/NAT helper")
Signed-off-by: Lena Wang <lena.wang@mediatek.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9999378996 ]
Following is rejected but should be allowed:
table inet t {
ct expectation exp1 {
[..]
l3proto ip
Valid combos are:
table ip t, l3proto ip
table ip6 t, l3proto ip6
table inet t, l3proto ip OR l3proto ip6
Disallow inet pseudeo family, the l3num must be a on-wire protocol known
to conntrack.
Retain NFPROTO_INET case to make it clear its rejected
intentionally rather as oversight.
Fixes: 8059918a13 ("netfilter: nft_ct: sanitize layer 3 and 4 protocol number in custom expectations")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b7fb7729c9 ]
This bug was noticed while re-implementing parts of the kernel
driver in userspace using spidev. The goal was to enable some
of the errata workarounds that Microchip describes in their
errata sheet [1].
Both the errata sheet and the regular datasheet of e.g. the KSZ8795
imply that you need to do this for indirect register accesses:
- write a 16-bit value to a control register pair (this value
consists of the indirect register table, and the offset inside
the table)
- either read or write an 8-bit value from the data storage
register (indicated by REG_IND_BYTE in the kernel)
The current implementation has the order swapped. It can be
proven, by reading back some indirect register with known content
(the EEE register modified in ksz8_handle_global_errata() is one of
these), that this implementation does not work.
Private discussion with Oleksij Rempel of Pengutronix has revealed
that the workaround was apparantly never tested on actual hardware.
[1] https://ww1.microchip.com/downloads/aemDocuments/documents/OTH/ProductDocuments/Errata/KSZ87xx-Errata-DS80000687C.pdf
Signed-off-by: Tobias Jakobi (Compleo) <tobias.jakobi.compleo@gmail.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Fixes: 7b6e6235b6 ("net: dsa: microchip: ksz8795: handle eee specif erratum")
Link: https://lore.kernel.org/r/20240304154135.161332-1-tobias.jakobi.compleo@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2487007aa3 ]
When running an XDP program that is attached to a cpumap entry, we don't
initialise the xdp_rxq_info data structure being used in the xdp_buff
that backs the XDP program invocation. Tobias noticed that this leads to
random values being returned as the xdp_md->rx_queue_index value for XDP
programs running in a cpumap.
This means we're basically returning the contents of the uninitialised
memory, which is bad. Fix this by zero-initialising the rxq data
structure before running the XDP program.
Fixes: 9216477449 ("bpf: cpumap: Add the possibility to attach an eBPF program to cpumap")
Reported-by: Tobias Böhm <tobias@aibor.de>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20240305213132.11955-1-toke@redhat.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f267f26281 ]
Commit 9b0ed890ac ("bonding: do not report NETDEV_XDP_ACT_XSK_ZEROCOPY")
changed the driver from reporting everything as supported before a device
was bonded into having the driver report that no XDP feature is supported
until a real device is bonded as it seems to be more truthful given
eventually real underlying devices decide what XDP features are supported.
The change however did not take into account when all slave devices get
removed from the bond device. In this case after 9b0ed890ac, the driver
keeps reporting a feature mask of 0x77, that is, NETDEV_XDP_ACT_MASK &
~NETDEV_XDP_ACT_XSK_ZEROCOPY whereas it should have reported a feature
mask of 0.
Fix it by resetting XDP feature flags in the same way as if no XDP program
is attached to the bond device. This was uncovered by the XDP bond selftest
which let BPF CI fail. After adjusting the starting masks on the latter
to 0 instead of NETDEV_XDP_ACT_MASK the test passes again together with
this fix.
Fixes: 9b0ed890ac ("bonding: do not report NETDEV_XDP_ACT_XSK_ZEROCOPY")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Magnus Karlsson <magnus.karlsson@intel.com>
Cc: Prashant Batra <prbatra.mail@gmail.com>
Cc: Toke Høiland-Jørgensen <toke@redhat.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Message-ID: <20240305090829.17131-1-daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e9a8e5a587 ]
When comparing current and cached states verifier should consider
bpf_func_state->callback_depth. Current state cannot be pruned against
cached state, when current states has more iterations left compared to
cached state. Current state has more iterations left when it's
callback_depth is smaller.
Below is an example illustrating this bug, minimized from mailing list
discussion [0] (assume that BPF_F_TEST_STATE_FREQ is set).
The example is not a safe program: if loop_cb point (1) is followed by
loop_cb point (2), then division by zero is possible at point (4).
struct ctx {
__u64 a;
__u64 b;
__u64 c;
};
static void loop_cb(int i, struct ctx *ctx)
{
/* assume that generated code is "fallthrough-first":
* if ... == 1 goto
* if ... == 2 goto
* <default>
*/
switch (bpf_get_prandom_u32()) {
case 1: /* 1 */ ctx->a = 42; return 0; break;
case 2: /* 2 */ ctx->b = 42; return 0; break;
default: /* 3 */ ctx->c = 42; return 0; break;
}
}
SEC("tc")
__failure
__flag(BPF_F_TEST_STATE_FREQ)
int test(struct __sk_buff *skb)
{
struct ctx ctx = { 7, 7, 7 };
bpf_loop(2, loop_cb, &ctx, 0); /* 0 */
/* assume generated checks are in-order: .a first */
if (ctx.a == 42 && ctx.b == 42 && ctx.c == 7)
asm volatile("r0 /= 0;":::"r0"); /* 4 */
return 0;
}
Prior to this commit verifier built the following checkpoint tree for
this example:
.------------------------------------- Checkpoint / State name
| .-------------------------------- Code point number
| | .---------------------------- Stack state {ctx.a,ctx.b,ctx.c}
| | | .------------------- Callback depth in frame #0
v v v v
- (0) {7P,7P,7},depth=0
- (3) {7P,7P,7},depth=1
- (0) {7P,7P,42},depth=1
- (3) {7P,7,42},depth=2
- (0) {7P,7,42},depth=2 loop terminates because of depth limit
- (4) {7P,7,42},depth=0 predicted false, ctx.a marked precise
- (6) exit
(a) - (2) {7P,7,42},depth=2
- (0) {7P,42,42},depth=2 loop terminates because of depth limit
- (4) {7P,42,42},depth=0 predicted false, ctx.a marked precise
- (6) exit
(b) - (1) {7P,7P,42},depth=2
- (0) {42P,7P,42},depth=2 loop terminates because of depth limit
- (4) {42P,7P,42},depth=0 predicted false, ctx.{a,b} marked precise
- (6) exit
- (2) {7P,7,7},depth=1 considered safe, pruned using checkpoint (a)
(c) - (1) {7P,7P,7},depth=1 considered safe, pruned using checkpoint (b)
Here checkpoint (b) has callback_depth of 2, meaning that it would
never reach state {42,42,7}.
While checkpoint (c) has callback_depth of 1, and thus
could yet explore the state {42,42,7} if not pruned prematurely.
This commit makes forbids such premature pruning,
allowing verifier to explore states sub-tree starting at (c):
(c) - (1) {7,7,7P},depth=1
- (0) {42P,7,7P},depth=1
...
- (2) {42,7,7},depth=2
- (0) {42,42,7},depth=2 loop terminates because of depth limit
- (4) {42,42,7},depth=0 predicted true, ctx.{a,b,c} marked precise
- (5) division by zero
[0] https://lore.kernel.org/bpf/9b251840-7cb8-4d17-bd23-1fc8071d8eef@linux.dev/
Fixes: bb124da69c ("bpf: keep track of max number of bpf_loop callback iterations")
Suggested-by: Yonghong Song <yonghong.song@linux.dev>
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
Acked-by: Yonghong Song <yonghong.song@linux.dev>
Link: https://lore.kernel.org/r/20240222154121.6991-2-eddyz87@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef27f655b4 ]
When a frame can not be transmitted in XDP_REDIRECT
(e.g. due to a full queue), it is necessary to free
it by calling xdp_return_frame_rx_napi.
However, this is the responsibility of the caller of
the ndo_xdp_xmit (see for example bq_xmit_all in
kernel/bpf/devmap.c) and thus calling it inside
igc_xdp_xmit (which is the ndo_xdp_xmit of the igc
driver) as well will lead to memory corruption.
In fact, bq_xmit_all expects that it can return all
frames after the last successfully transmitted one.
Therefore, break for the first not transmitted frame,
but do not call xdp_return_frame_rx_napi in igc_xdp_xmit.
This is equally implemented in other Intel drivers
such as the igb.
There are two alternatives to this that were rejected:
1. Return num_frames as all the frames would have been
transmitted and release them inside igc_xdp_xmit.
While it might work technically, it is not what
the return value is meant to represent (i.e. the
number of SUCCESSFULLY transmitted packets).
2. Rework kernel/bpf/devmap.c and all drivers to
support non-consecutively dropped packets.
Besides being complex, it likely has a negative
performance impact without a significant gain
since it is anyway unlikely that the next frame
can be transmitted if the previous one was dropped.
The memory corruption can be reproduced with
the following script which leads to a kernel panic
after a few seconds. It basically generates more
traffic than a i225 NIC can transmit and pushes it
via XDP_REDIRECT from a virtual interface to the
physical interface where frames get dropped.
#!/bin/bash
INTERFACE=enp4s0
INTERFACE_IDX=`cat /sys/class/net/$INTERFACE/ifindex`
sudo ip link add dev veth1 type veth peer name veth2
sudo ip link set up $INTERFACE
sudo ip link set up veth1
sudo ip link set up veth2
cat << EOF > redirect.bpf.c
SEC("prog")
int redirect(struct xdp_md *ctx)
{
return bpf_redirect($INTERFACE_IDX, 0);
}
char _license[] SEC("license") = "GPL";
EOF
clang -O2 -g -Wall -target bpf -c redirect.bpf.c -o redirect.bpf.o
sudo ip link set veth2 xdp obj redirect.bpf.o
cat << EOF > pass.bpf.c
SEC("prog")
int pass(struct xdp_md *ctx)
{
return XDP_PASS;
}
char _license[] SEC("license") = "GPL";
EOF
clang -O2 -g -Wall -target bpf -c pass.bpf.c -o pass.bpf.o
sudo ip link set $INTERFACE xdp obj pass.bpf.o
cat << EOF > trafgen.cfg
{
/* Ethernet Header */
0xe8, 0x6a, 0x64, 0x41, 0xbf, 0x46,
0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
const16(ETH_P_IP),
/* IPv4 Header */
0b01000101, 0, # IPv4 version, IHL, TOS
const16(1028), # IPv4 total length (UDP length + 20 bytes (IP header))
const16(2), # IPv4 ident
0b01000000, 0, # IPv4 flags, fragmentation off
64, # IPv4 TTL
17, # Protocol UDP
csumip(14, 33), # IPv4 checksum
/* UDP Header */
10, 0, 1, 1, # IP Src - adapt as needed
10, 0, 1, 2, # IP Dest - adapt as needed
const16(6666), # UDP Src Port
const16(6666), # UDP Dest Port
const16(1008), # UDP length (UDP header 8 bytes + payload length)
csumudp(14, 34), # UDP checksum
/* Payload */
fill('W', 1000),
}
EOF
sudo trafgen -i trafgen.cfg -b3000MB -o veth1 --cpp
Fixes: 4ff3203610 ("igc: Add support for XDP_REDIRECT action")
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 06e456a05d ]
The function ice_bridge_setlink() may encounter a NULL pointer dereference
if nlmsg_find_attr() returns NULL and br_spec is dereferenced subsequently
in nla_for_each_nested(). To address this issue, add a check to ensure that
br_spec is not NULL before proceeding with the nested attribute iteration.
Fixes: b1edc14a3f ("ice: Implement ice_bridge_getlink and ice_bridge_setlink")
Signed-off-by: Rand Deeb <rand.sec96@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2652b99e43 ]
The E800 series hardware uses the same iAVF driver as older devices,
including the virtchnl negotiation scheme.
This negotiation scheme includes a mechanism to determine what type of RSS
should be supported, including RSS over PF virtchnl messages, RSS over
firmware AdminQ messages, and RSS via direct register access.
The PF driver will always prefer VIRTCHNL_VF_OFFLOAD_RSS_PF if its
supported by the VF driver. However, if an older VF driver is loaded, it
may request only VIRTCHNL_VF_OFFLOAD_RSS_REG or VIRTCHNL_VF_OFFLOAD_RSS_AQ.
The ice driver happily agrees to support these methods. Unfortunately, the
underlying hardware does not support these mechanisms. The E800 series VFs
don't have the appropriate registers for RSS_REG. The mailbox queue used by
VFs for VF to PF communication blocks messages which do not have the
VF-to-PF opcode.
Stop lying to the VF that it could support RSS over AdminQ or registers, as
these interfaces do not work when the hardware is operating on an E800
series device.
In practice this is unlikely to be hit by any normal user. The iAVF driver
has supported RSS over PF virtchnl commands since 2016, and always defaults
to using RSS_PF if possible.
In principle, nothing actually stops the existing VF from attempting to
access the registers or send an AQ command. However a properly coded VF
will check the capability flags and will report a more useful error if it
detects a case where the driver does not support the RSS offloads that it
does.
Fixes: 1071a8358a ("ice: Implement virtchnl commands for AVF support")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Alan Brady <alan.brady@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89d72d4125 ]
Based on the static analyzis of the code it looks like when an entry
from the MAC table was removed, the entry was still used after being
freed. More precise the vid of the mac_entry was used after calling
devm_kfree on the mac_entry.
The fix consists in first using the vid of the mac_entry to delete the
entry from the HW and after that to free it.
Fixes: b37a1bae74 ("net: sparx5: add mactable support")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240301080608.3053468-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51270d573a ]
I'm updating __assign_str() and will be removing the second parameter. To
make sure that it does not break anything, I make sure that it matches the
__string() field, as that is where the string is actually going to be
saved in. To make sure there's nothing that breaks, I added a WARN_ON() to
make sure that what was used in __string() is the same that is used in
__assign_str().
In doing this change, an error was triggered as __assign_str() now expects
the string passed in to be a char * value. I instead had the following
warning:
include/trace/events/qdisc.h: In function ‘trace_event_raw_event_qdisc_reset’:
include/trace/events/qdisc.h:91:35: error: passing argument 1 of 'strcmp' from incompatible pointer type [-Werror=incompatible-pointer-types]
91 | __assign_str(dev, qdisc_dev(q));
That's because the qdisc_enqueue() and qdisc_reset() pass in qdisc_dev(q)
to __assign_str() and to __string(). But that function returns a pointer
to struct net_device and not a string.
It appears that these events are just saving the pointer as a string and
then reading it as a string as well.
Use qdisc_dev(q)->name to save the device instead.
Fixes: a34dac0b90 ("net_sched: add tracepoints for qdisc_reset() and qdisc_destroy()")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 90502d433c ]
The NAPI poll context is a softirq context. Do not use normal spinlock API
in this context to prevent concurrency issues.
Fixes: 3178308ad4 ("net/mlx5e: Make tx_port_ts logic resilient to out-of-order CQEs")
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
CC: Vadim Fedorenko <vadfed@meta.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b7cf07586c ]
Just simply reordering the functions mlx5e_ptp_metadata_map_put and
mlx5e_ptpsq_track_metadata in the mlx5e_txwqe_complete context is not good
enough since both the compiler and CPU are free to reorder these two
functions. If reordering does occur, the issue that was supposedly fixed by
7e3f3ba97e ("net/mlx5e: Track xmit submission to PTP WQ after populating
metadata map") will be seen. This will lead to NULL pointer dereferences in
mlx5e_ptpsq_mark_ts_cqes_undelivered in the NAPI polling context due to the
tracking list being populated before the metadata map.
Fixes: 7e3f3ba97e ("net/mlx5e: Track xmit submission to PTP WQ after populating metadata map")
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
CC: Vadim Fedorenko <vadfed@meta.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a71f2147b6 ]
The packet number attribute of the SA is incremented by the device rather
than the software stack when enabling hardware offload. Because the packet
number attribute is managed by the hardware, the software has no insight
into the value of the packet number attribute actually written by the
device.
Previously when MACsec offload was enabled, the hardware object for
handling the offload was destroyed when the SA was disabled. Re-enabling
the SA would lead to a new hardware object being instantiated. This new
hardware object would not have any recollection of the correct packet
number for the SA. Instead, destroy the flow steering rule when
deactivating the SA and recreate it upon reactivation, preserving the
original hardware object.
Fixes: 8ff0ac5be1 ("net/mlx5: Add MACsec offload Tx command support")
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd238b7020 ]
Downgrade the print from mlx5_core_warn() to mlx5_core_dbg(), as it
is just a statement of fact that firmware doesn't support ignore flow
level.
And change the wording to "firmware flow level support is missing", to
make it more accurate.
Fixes: ae2ee3be99 ("net/mlx5: CT: Remove warning of ignore_flow_level support for VFs")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Suggested-by: Elliott, Robert (Servers) <elliott@hpe.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5e6107b499 ]
Functions which can't access MFRL (Management Firmware Reset Level)
register, have no use of fw_reset structures or events. Remove fw_reset
structures allocation and registration for fw reset events notifications
for these functions.
Having the devlink param enable_remote_dev_reset on functions that don't
have this capability is misleading as these functions are not allowed to
influence the reset flow. Hence, this patch removes this parameter for
such functions.
In addition, return not supported on devlink reload action fw_activate
for these functions.
Fixes: 38b9f903f2 ("net/mlx5: Handle sync reset request event")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 85ea2c5c5e ]
The checking in the cited commit is not accurate. In the common case,
VF destination is internal, and uplink destination is external.
However, uplink destination with packet reformat is considered as
internal because firmware uses LB+hairpin to support it. Update the
checking so header rewrite rules with both internal and external
destinations are not allowed.
Fixes: e0e22d59b4 ("net/mlx5: E-switch, Add checking for flow rule destinations")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b7bbd698c9 ]
This reverts commit 4e25b661f4.
This Commit was mistakenly applied by pulling the wrong tag, remove it.
Fixes: 4e25b661f4 ("net/mlx5e: Check the number of elements before walk TC rhashtable")
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8deeefb247 ]
This reverts commit 662404b24a.
The revert is required due to the suspicion it is not good for anything
and cause crash.
Fixes: 662404b24a ("net/mlx5e: Block entering switchdev mode with ns inconsistency")
Signed-off-by: Gavin Li <gavinl@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 99099c6bc7 ]
ice_qp_dis() currently does things in very mixed way. Tx is stopped
before disabling IRQ on related queue vector, then it takes care of
disabling Rx and finally NAPI is disabled.
Let us start with disabling IRQs in the first place followed by turning
off NAPI. Then it is safe to handle queues.
One subtle change on top of that is that even though ice_qp_ena() looks
more sane, clear ICE_CFG_BUSY as the last thing there.
Fixes: 2d4238f556 ("ice: Add support for AF_XDP")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d562b11c1e ]
Disable NAPI before shutting down queues that this particular NAPI
contains so that the order of actions in i40e_queue_pair_disable()
mirrors what we do in i40e_queue_pair_enable().
Fixes: 123cecd427 ("i40e: added queue pair disable/enable functions")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cbf996f52c ]
Currently routines that are supposed to toggle state of ring pair do not
take care of associated interrupt with queue vector that these rings
belong to. This causes funky issues such as dead interface due to irq
misconfiguration, as per Pavel's report from Closes: tag.
Add a function responsible for disabling single IRQ in EIMC register and
call this as a very first thing when disabling ring pair during xsk_pool
setup. For enable let's reuse ixgbe_irq_enable_queues(). Besides this,
disable/enable NAPI as first/last thing when dealing with closing or
opening ring pair that xsk_pool is being configured on.
Reported-by: Pavel Vazharov <pavel@x3me.net>
Closes: https://lore.kernel.org/netdev/CAJEV1ijxNyPTwASJER1bcZzS9nMoZJqfR86nu_3jFFVXzZQ4NA@mail.gmail.com/
Fixes: 024aa5800f ("ixgbe: added Rx/Tx ring disable/enable functions")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1eecc7ab82 ]
Current driver has some asymmetry in the runtime PM calls. On lan78xx_open()
it will call usb_autopm_get() and unconditionally usb_autopm_put(). And
on lan78xx_stop() it will call only usb_autopm_put(). So far, it was
working only because this driver do not activate autosuspend by default,
so it was visible only by warning "Runtime PM usage count underflow!".
Since, with current driver, we can't use runtime PM with active link,
execute lan78xx_open()->usb_autopm_put() only in error case. Otherwise,
keep ref counting high as long as interface is open.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51d31149a8 ]
The addition of bal_rank_mask with encoding version 17 was merged
into ceph.git in Oct 2022 and made it into v18.2.0 release normally.
A few months later, the much delayed addition of max_xattr_size got
merged, also with encoding version 17, placed before bal_rank_mask
in the encoding -- but it didn't make v18.2.0 release.
The way this ended up being resolved on the MDS side is that
bal_rank_mask will continue to be encoded in version 17 while
max_xattr_size is now encoded in version 18. This does mean that
older kernels will misdecode version 17, but this is also true for
v18.2.0 and v18.2.1 clients in userspace.
The best we can do is backport this adjustment -- see ceph.git
commit 78abfeaff27fee343fb664db633de5b221699a73 for details.
[ idryomov: changelog ]
Cc: stable@vger.kernel.org
Link: https://tracker.ceph.com/issues/64440
Fixes: d93231a6bc ("ceph: prevent a client from exceeding the MDS maximum xattr size")
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: Patrick Donnelly <pdonnell@ibm.com>
Reviewed-by: Venky Shankar <vshankar@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e9b052582 ]
Introduce a common dt-bindings header file, fsl-edma.h, shared between
the driver and dts files. This addition aims to eliminate hardcoded values
in dts files, promoting maintainability and consistency.
DTS header file not support BIT() macro yet. Directly use 2^n number.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20231114154824.3617255-3-Frank.Li@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Stable-dep-of: a79f949a5c ("dmaengine: fsl-edma: correct max_segment_size setting")
Signed-off-by: Sasha Levin <sashal@kernel.org>
dw_axi_dma_interrupt disables interrupts for the duration of the channel
handling. It does so by clearing a bit in the DMA_CFG register - an
action that involves a read-modify-write. That in itself would be safe
because there will be no further interrupts, hence no reentrancy, were
it the only bit of code accessing that register.
The only neighbour of INT_EN is DMAC_EN - the main enable for the block.
That's not the sort of thing you would expect to be modified during the
normal course of operation, but bizarrely it is set at the start of the
transfer of every block, in axi_chan_block_xfer_star, by a call to
axi_dma_enable. This can lead to INT_EN being accidentally cleared,
which causes all DMA transfers to time out.
One might think that the enabling was being delayed until the first
transfer, but the probe function calls axi_dma_resume which in turn
calls axi_dma_enable, so that isn't the case.
Fix the atomicity problem by removing the spurious call to
axi_dma_enable.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Add a 'base' parameter to set an explicit bus number for the channels,
where the requested bus number is base + channel ID.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
i2c_mux_add_adapter takes a force_nr parameter that allows an explicit
bus number to be associated with a channel. However, only i2c-mux-reg
and i2c-mux-gpio make use of it.
To help with situations where it is desirable to have a fixed, known
base address for the channels of a mux, create a "base-nr" property.
When force_nr is 0 and base-nr is set and non-zero, form a force_nr
value from the sum of base-nr and the channel ID.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The driver has been converted to use gpiod, which will normalise
polarity based on DT.
The piscreen overlay (and others) incorrectly defines the pendown
GPIO as being ACTIVE_HIGH (0), althought triggering on the high-low
edge for pen down. It therefore tries reading the pen position when
not being touched, and stops when it is touched.
Tested with piscreen and ads7846 overlays. Also fixed on others
where the interrupt says high->low but the polarity was ACTIVE_HIGH.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
When running multiple muxes, in order to be able to reuse the
same address on child buses of different muxes you have to
disconnect the mux after every transaction.
Add an override to select that option.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
While waiting for random data, use sleeps that are proportional
to the amount of data expected. Prevent indefinite waits by
giving up if nothing is received for a second.
See: https://github.com/raspberrypi/linux/issues/5390
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
With the RP1 PWM configured to use the 50MHz oscillator clock source,
requesting a 100MHz clock will fail. Set the RP1 PWM clock rate to
50MHz, do the same to other Pi PWM blocks, and remove the default
clock override in the PWM overlays. However, an explicit
"clock=..." parameter is still supported.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Through emperical testing, the sensor can crop upto a 96x88 window to
produce a valid Bayer frame. Adjust the ROIWH1_MIN ROIWV1_MIN
appropriately for this limit.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Add support for setting horizontal and/or vertial flips in the IMX296
sensor through the V4L2_CID_HFLIP and V4L2_CID_VFLIP controls.
Add a new helper function to return the media bus format code that
depends on the sensor flips.
Grab the V4L2_CID_HFLIP and V4L2_CID_VFLIP controls on stream on, and
release on stream off to ensure flips cannot be changed while the sensor
is streaming.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Set the gain delay to 1 frame in the sensor. This avoids any race
condition or ambiguity over when the setting is applied through
userland.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Add a helper function to setup the horizontal blanking control. Update
the control limits on set_format as the horizontal blanking time must
remain constant regardless of sensor output width.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Add a missing register write (MIPIC_AREA3W) when setting up a crop
window in the sensor to get this functionality working.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
The DWC I2S driver treats the channel count register values as if they
encode a power of two (2, 4, 8, 16), but they actually encode a
multiple of 2 (2, 4, 6, 8).
Also improve the error message when asked for an unsupported number
of channels.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Not all panels use all 4 data lanes, so allow configuration based
on the compatible string.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
This new panel uses the ILI9881C IC but needs an alternate
init sequence, and therefore requires a new compatible string.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The newer Raspberry Pi 5" and 7" panels have a slightly different
register map to the original one.
Add a new driver for this regulator.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
commit 346c84e281 upstream.
Since commit 363d0e5628 ("media: pwm-ir-tx: Trigger edges from
hrtimer interrupt context"), pwm-ir-tx uses high resolution timers
for IR signal generation when the pwm can be used from atomic context.
Ensure they are available.
Fixes: 363d0e5628 ("media: pwm-ir-tx: Trigger edges from hrtimer interrupt context")
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
commit 363d0e5628 upstream.
This makes the generated IR much more precise. Before this change, the
driver is unreliable and many users opted to use gpio-ir-tx instead.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
commit fcc7607293 upstream.
clk_get_rate() may do a mutex lock. Fetch the clock rate once, and prevent
rate changes using clk_rate_exclusive_get().
Signed-off-by: Sean Young <sean@mess.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
commit 7170d3beaf upstream.
Some PWM devices require sleeping, for example if the pwm device is
connected over I2C. However, many PWM devices could be used from atomic
context, e.g. memory mapped PWM. This is useful for, for example, the
pwm-ir-tx driver which requires precise timing. Sleeping causes havoc
with the generated IR signal.
Since not all PWM devices can support atomic context, we also add a
pwm_might_sleep() function to check if is not supported.
Signed-off-by: Sean Young <sean@mess.org>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
commit c748a6d77c upstream.
In order to introduce a pwm api which can be used from atomic context,
we will need two functions for applying pwm changes:
int pwm_apply_might_sleep(struct pwm *, struct pwm_state *);
int pwm_apply_atomic(struct pwm *, struct pwm_state *);
This commit just deals with renaming pwm_apply_state(), a following
commit will introduce the pwm_apply_atomic() function.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> # for input
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Lee Jones <lee@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
commit 2ce7b7f670 upstream.
With devm_clk_get_enabled() the call to clk_disable_unprepare() can be
dropped from the error path and the remove callback. With
devm_pwmchip_add() pwmchip_remove() can be dropped. Then the remove
callback is empty and can go away, too. With bcm2835_pwm_remove() the only
user of platform_get_drvdata() is gone and so platform_set_drvdata() can
be dropped from .probe(), too.
Also use dev_err_probe() for simplified (and improved) error reporting.
Link: https://lore.kernel.org/r/20230929161918.2410424-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
commit 8077541288 upstream.
This patch adds a new helper chk_subflows_total(), in it use the newly
added counter mptcpi_subflows_total to get the "correct" amount of
subflows, including the initial one.
To be compatible with old 'ss' or kernel versions not supporting this
counter, get the total subflows by listing TCP connections that are
MPTCP subflows:
ss -ti state state established state syn-sent state syn-recv |
grep -c tcp-ulp-mptcp.
Reviewed-by: Matthieu Baerts <matttbe@kernel.org>
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <martineau@kernel.org>
Link: https://lore.kernel.org/r/20231128-send-net-next-2023107-v4-3-8d6b94150f6b@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 06848c0f34 upstream.
This patch adds a new helper get_info_value(), using 'sed' command to
parse the value of the given item name in the line with the given keyword,
to make chk_mptcp_info() and pedit_action_pkts() more readable.
Also add another helper evts_get_info() to use get_info_value() to parse
the output of 'pm_nl_ctl events' command, to make all the userspace pm
selftests more readable, both in mptcp_join.sh and userspace_pm.sh.
Reviewed-by: Matthieu Baerts <matttbe@kernel.org>
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <martineau@kernel.org>
Link: https://lore.kernel.org/r/20231128-send-net-next-2023107-v4-2-8d6b94150f6b@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 43fb862de8 upstream.
During VMentry VERW is executed to mitigate MDS. After VERW, any memory
access like register push onto stack may put host data in MDS affected
CPU buffers. A guest can then use MDS to sample host data.
Although likelihood of secrets surviving in registers at current VERW
callsite is less, but it can't be ruled out. Harden the MDS mitigation
by moving the VERW mitigation late in VMentry path.
Note that VERW for MMIO Stale Data mitigation is unchanged because of
the complexity of per-guest conditional VERW which is not easy to handle
that late in asm with no GPRs available. If the CPU is also affected by
MDS, VERW is unconditionally executed late in asm regardless of guest
having MMIO access.
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Sean Christopherson <seanjc@google.com>
Link: https://lore.kernel.org/all/20240213-delay-verw-v8-6-a6216d83edb7%40linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c7501722e upstream.
Mitigation for MDS is to use VERW instruction to clear any secrets in
CPU Buffers. Any memory accesses after VERW execution can still remain
in CPU buffers. It is safer to execute VERW late in return to user path
to minimize the window in which kernel data can end up in CPU buffers.
There are not many kernel secrets to be had after SWITCH_TO_USER_CR3.
Add support for deploying VERW mitigation after user register state is
restored. This helps minimize the chances of kernel data ending up into
CPU buffers after executing VERW.
Note that the mitigation at the new location is not yet enabled.
Corner case not handled
=======================
Interrupts returning to kernel don't clear CPUs buffers since the
exit-to-user path is expected to do that anyways. But, there could be
a case when an NMI is generated in kernel after the exit-to-user path
has cleared the buffers. This case is not handled and NMI returning to
kernel don't clear CPU buffers because:
1. It is rare to get an NMI after VERW, but before returning to userspace.
2. For an unprivileged user, there is no known way to make that NMI
less rare or target it.
3. It would take a large number of these precisely-timed NMIs to mount
an actual attack. There's presumably not enough bandwidth.
4. The NMI in question occurs after a VERW, i.e. when user state is
restored and most interesting data is already scrubbed. Whats left
is only the data that NMI touches, and that may or may not be of
any interest.
[ pawan: resolved conflict for hunk swapgs_restore_regs_and_return_to_usermode in backport ]
Suggested-by: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lore.kernel.org/all/20240213-delay-verw-v8-2-a6216d83edb7%40linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7838b46561 ]
In commit 19416123ab ("block: define 'struct bvec_iter' as packed"),
what we need is to save the 4byte padding, and avoid `bio` to spread on
one extra cache line.
It is enough to define it as '__packed __aligned(4)', as '__packed'
alone means byte aligned, and can cause compiler to generate horrible
code on architectures that don't support unaligned access in case that
bvec_iter is embedded in other structures.
Cc: Mikulas Patocka <mpatocka@redhat.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes: 19416123ab ("block: define 'struct bvec_iter' as packed")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 530b1dbd97 ]
Chip outputs are enabled[1] before actual reset is performed[2] which might
cause pin output value to flip flop if previous pin value was set to 1.
Fix that behavior by making sure chip is fully reset before all outputs are
enabled.
Flip-flop can be noticed when module is removed and inserted again and one of
the pins was changed to 1 before removal. 100 microsecond flipping is
noticeable on oscilloscope (100khz SPI bus).
For a properly reset chip - output is enabled around 100 microseconds (on 100khz
SPI bus) later during probing process hence should be irrelevant behavioral
change.
Fixes: 7ebc194d0f (gpio: 74x164: Introduce 'enable-gpios' property)
Link: https://elixir.bootlin.com/linux/v6.7.4/source/drivers/gpio/gpio-74x164.c#L130 [1]
Link: https://elixir.bootlin.com/linux/v6.7.4/source/drivers/gpio/gpio-74x164.c#L150 [2]
Signed-off-by: Arturas Moskvinas <arturas.moskvinas@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fad87dbd48 ]
The PAPR spec spells the function name as
"ibm,reset-pe-dma-windows"
but in practice firmware uses the singular form:
"ibm,reset-pe-dma-window"
in the device tree. Since we have the wrong spelling in the RTAS
function table, reverse lookups (token -> name) fail and warn:
unexpected failed lookup for token 86
WARNING: CPU: 1 PID: 545 at arch/powerpc/kernel/rtas.c:659 __do_enter_rtas_trace+0x2a4/0x2b4
CPU: 1 PID: 545 Comm: systemd-udevd Not tainted 6.8.0-rc4 #30
Hardware name: IBM,9105-22A POWER10 (raw) 0x800200 0xf000006 of:IBM,FW1060.00 (NL1060_028) hv:phyp pSeries
NIP [c0000000000417f0] __do_enter_rtas_trace+0x2a4/0x2b4
LR [c0000000000417ec] __do_enter_rtas_trace+0x2a0/0x2b4
Call Trace:
__do_enter_rtas_trace+0x2a0/0x2b4 (unreliable)
rtas_call+0x1f8/0x3e0
enable_ddw.constprop.0+0x4d0/0xc84
dma_iommu_dma_supported+0xe8/0x24c
dma_set_mask+0x5c/0xd8
mlx5_pci_init.constprop.0+0xf0/0x46c [mlx5_core]
probe_one+0xfc/0x32c [mlx5_core]
local_pci_probe+0x68/0x12c
pci_call_probe+0x68/0x1ec
pci_device_probe+0xbc/0x1a8
really_probe+0x104/0x570
__driver_probe_device+0xb8/0x224
driver_probe_device+0x54/0x130
__driver_attach+0x158/0x2b0
bus_for_each_dev+0xa8/0x120
driver_attach+0x34/0x48
bus_add_driver+0x174/0x304
driver_register+0x8c/0x1c4
__pci_register_driver+0x68/0x7c
mlx5_init+0xb8/0x118 [mlx5_core]
do_one_initcall+0x60/0x388
do_init_module+0x7c/0x2a4
init_module_from_file+0xb4/0x108
idempotent_init_module+0x184/0x34c
sys_finit_module+0x90/0x114
And oopses are possible when lockdep is enabled or the RTAS
tracepoints are active, since those paths dereference the result of
the lookup.
Use the correct spelling to match firmware's behavior, adjusting the
related constants to match.
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Fixes: 8252b88294 ("powerpc/rtas: improve function information lookups")
Reported-by: Gaurav Batra <gbatra@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20240222-rtas-fix-ibm-reset-pe-dma-window-v1-1-7aaf235ac63c@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09a3c1e461 ]
When kdump kernel tries to copy dump data over SR-IOV, LPAR panics due
to NULL pointer exception:
Kernel attempted to read user page (0) - exploit attempt? (uid: 0)
BUG: Kernel NULL pointer dereference on read at 0x00000000
Faulting instruction address: 0xc000000020847ad4
Oops: Kernel access of bad area, sig: 11 [#1]
LE PAGE_SIZE=64K MMU=Radix SMP NR_CPUS=2048 NUMA pSeries
Modules linked in: mlx5_core(+) vmx_crypto pseries_wdt papr_scm libnvdimm mlxfw tls psample sunrpc fuse overlay squashfs loop
CPU: 12 PID: 315 Comm: systemd-udevd Not tainted 6.4.0-Test102+ #12
Hardware name: IBM,9080-HEX POWER10 (raw) 0x800200 0xf000006 of:IBM,FW1060.00 (NH1060_008) hv:phyp pSeries
NIP: c000000020847ad4 LR: c00000002083b2dc CTR: 00000000006cd18c
REGS: c000000029162ca0 TRAP: 0300 Not tainted (6.4.0-Test102+)
MSR: 800000000280b033 <SF,VEC,VSX,EE,FP,ME,IR,DR,RI,LE> CR: 48288244 XER: 00000008
CFAR: c00000002083b2d8 DAR: 0000000000000000 DSISR: 40000000 IRQMASK: 1
...
NIP _find_next_zero_bit+0x24/0x110
LR bitmap_find_next_zero_area_off+0x5c/0xe0
Call Trace:
dev_printk_emit+0x38/0x48 (unreliable)
iommu_area_alloc+0xc4/0x180
iommu_range_alloc+0x1e8/0x580
iommu_alloc+0x60/0x130
iommu_alloc_coherent+0x158/0x2b0
dma_iommu_alloc_coherent+0x3c/0x50
dma_alloc_attrs+0x170/0x1f0
mlx5_cmd_init+0xc0/0x760 [mlx5_core]
mlx5_function_setup+0xf0/0x510 [mlx5_core]
mlx5_init_one+0x84/0x210 [mlx5_core]
probe_one+0x118/0x2c0 [mlx5_core]
local_pci_probe+0x68/0x110
pci_call_probe+0x68/0x200
pci_device_probe+0xbc/0x1a0
really_probe+0x104/0x540
__driver_probe_device+0xb4/0x230
driver_probe_device+0x54/0x130
__driver_attach+0x158/0x2b0
bus_for_each_dev+0xa8/0x130
driver_attach+0x34/0x50
bus_add_driver+0x16c/0x300
driver_register+0xa4/0x1b0
__pci_register_driver+0x68/0x80
mlx5_init+0xb8/0x100 [mlx5_core]
do_one_initcall+0x60/0x300
do_init_module+0x7c/0x2b0
At the time of LPAR dump, before kexec hands over control to kdump
kernel, DDWs (Dynamic DMA Windows) are scanned and added to the FDT.
For the SR-IOV case, default DMA window "ibm,dma-window" is removed from
the FDT and DDW added, for the device.
Now, kexec hands over control to the kdump kernel.
When the kdump kernel initializes, PCI busses are scanned and IOMMU
group/tables created, in pci_dma_bus_setup_pSeriesLP(). For the SR-IOV
case, there is no "ibm,dma-window". The original commit: b1fc44eaa9,
fixes the path where memory is pre-mapped (direct mapped) to the DDW.
When TCEs are direct mapped, there is no need to initialize IOMMU
tables.
iommu_table_setparms_lpar() only considers "ibm,dma-window" property
when initiallizing IOMMU table. In the scenario where TCEs are
dynamically allocated for SR-IOV, newly created IOMMU table is not
initialized. Later, when the device driver tries to enter TCEs for the
SR-IOV device, NULL pointer execption is thrown from iommu_area_alloc().
The fix is to initialize the IOMMU table with DDW property stored in the
FDT. There are 2 points to remember:
1. For the dedicated adapter, kdump kernel would encounter both
default and DDW in FDT. In this case, DDW property is used to
initialize the IOMMU table.
2. A DDW could be direct or dynamic mapped. kdump kernel would
initialize IOMMU table and mark the existing DDW as
"dynamic". This works fine since, at the time of table
initialization, iommu_table_clear() makes some space in the
DDW, for some predefined number of TCEs which are needed for
kdump to succeed.
Fixes: b1fc44eaa9 ("pseries/iommu/ddw: Fix kdump to work in absence of ibm,dma-window")
Signed-off-by: Gaurav Batra <gbatra@linux.vnet.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20240125203017.61014-1-gbatra@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ecec7c9f29 ]
head is defined in idxd->evl as a shadow of head in the EVLSTATUS register.
There are two issues related to the shadow head:
1. Mismatch between the shadow head and the state of the EVLSTATUS
register:
If Event Log is supported, upon completion of the Enable Device command,
the Event Log head in the variable idxd->evl->head should be cleared to
match the state of the EVLSTATUS register. But the variable is not reset
currently, leading mismatch between the variable and the register state.
The mismatch causes incorrect processing of Event Log entries.
2. Unnecessary shadow head definition:
The shadow head is unnecessary as head can be read directly from the
EVLSTATUS register. Reading head from the register incurs no additional
cost because event log head and tail are always read together and
tail is already read directly from the register as required by hardware.
Remove the shadow Event Log head stored in idxd->evl to address the
mentioned issues.
Fixes: 244da66cda ("dmaengine: idxd: setup event log configuration")
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20240215024931.1739621-1-fenghua.yu@intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd665bfc75 ]
The current check of ch_en enabled to know the maximum number of available
hardware channels is wrong as it check the number of ch_en register set
but all of them are unset at probe. This register is set at the
dw_hdma_v0_core_start function which is run lately before a DMA transfer.
The HDMA IP have no way to know the number of hardware channels available
like the eDMA IP, then let set it to maximum channels and let the platform
set the right number of channels.
Fixes: e74c39573d ("dmaengine: dw-edma: Add support for native HDMA")
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://lore.kernel.org/r/20240129-b4-feature_hdma_mainline-v7-1-8e8c1acb7a46@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit aa82ac51d6 upstream.
syzbot reported another task hung in __unix_gc(). [0]
The current while loop assumes that all of the left candidates
have oob_skb and calling kfree_skb(oob_skb) releases the remaining
candidates.
However, I missed a case that oob_skb has self-referencing fd and
another fd and the latter sk is placed before the former in the
candidate list. Then, the while loop never proceeds, resulting
the task hung.
__unix_gc() has the same loop just before purging the collected skb,
so we can call kfree_skb(oob_skb) there and let __skb_queue_purge()
release all inflight sockets.
[0]:
Sending NMI from CPU 0 to CPUs 1:
NMI backtrace for cpu 1
CPU: 1 PID: 2784 Comm: kworker/u4:8 Not tainted 6.8.0-rc4-syzkaller-01028-g71b605d32017 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/25/2024
Workqueue: events_unbound __unix_gc
RIP: 0010:__sanitizer_cov_trace_pc+0x0/0x70 kernel/kcov.c:200
Code: 89 fb e8 23 00 00 00 48 8b 3d 84 f5 1a 0c 48 89 de 5b e9 43 26 57 00 0f 1f 00 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 <f3> 0f 1e fa 48 8b 04 24 65 48 8b 0d 90 52 70 7e 65 8b 15 91 52 70
RSP: 0018:ffffc9000a17fa78 EFLAGS: 00000287
RAX: ffffffff8a0a6108 RBX: ffff88802b6c2640 RCX: ffff88802c0b3b80
RDX: 0000000000000000 RSI: 0000000000000002 RDI: 0000000000000000
RBP: ffffc9000a17fbf0 R08: ffffffff89383f1d R09: 1ffff1100ee5ff84
R10: dffffc0000000000 R11: ffffed100ee5ff85 R12: 1ffff110056d84ee
R13: ffffc9000a17fae0 R14: 0000000000000000 R15: ffffffff8f47b840
FS: 0000000000000000(0000) GS:ffff8880b9500000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007ffef5687ff8 CR3: 0000000029b34000 CR4: 00000000003506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<NMI>
</NMI>
<TASK>
__unix_gc+0xe69/0xf40 net/unix/garbage.c:343
process_one_work kernel/workqueue.c:2633 [inline]
process_scheduled_works+0x913/0x1420 kernel/workqueue.c:2706
worker_thread+0xa5f/0x1000 kernel/workqueue.c:2787
kthread+0x2ef/0x390 kernel/kthread.c:388
ret_from_fork+0x4b/0x80 arch/x86/kernel/process.c:147
ret_from_fork_asm+0x1b/0x30 arch/x86/entry/entry_64.S:242
</TASK>
Reported-and-tested-by: syzbot+ecab4d36f920c3574bf9@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=ecab4d36f920c3574bf9
Fixes: 25236c91b5 ("af_unix: Fix task hung while purging oob_skb in GC.")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when AOP_WRITEPAGE_ACTIVATE is returned (as NFS does when it detects
congestion) it is important that the folio is redirtied.
nfs_writepage_locked() doesn't do this, so files can become corrupted as
writes can be lost.
Note that this is not needed in v6.8 as AOP_WRITEPAGE_ACTIVATE cannot be
returned. It is needed for kernels v5.18..v6.7. Prior to 6.3 the patch
is different as it needs to mention "page", not "folio".
Reported-and-tested-by: Jacek Tomaka <Jacek.Tomaka@poczta.fm>
Fixes: 6df25e5853 ("nfs: remove reliance on bdi congestion")
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 10048689de upstream.
when MPTCP server accepts an incoming connection, it clones its listener
socket. However, the pointer to 'inet_opt' for the new socket has the same
value as the original one: as a consequence, on program exit it's possible
to observe the following splat:
BUG: KASAN: double-free in inet_sock_destruct+0x54f/0x8b0
Free of addr ffff888485950880 by task swapper/25/0
CPU: 25 PID: 0 Comm: swapper/25 Kdump: loaded Not tainted 6.8.0-rc1+ #609
Hardware name: Supermicro SYS-6027R-72RF/X9DRH-7TF/7F/iTF/iF, BIOS 3.0 07/26/2013
Call Trace:
<IRQ>
dump_stack_lvl+0x32/0x50
print_report+0xca/0x620
kasan_report_invalid_free+0x64/0x90
__kasan_slab_free+0x1aa/0x1f0
kfree+0xed/0x2e0
inet_sock_destruct+0x54f/0x8b0
__sk_destruct+0x48/0x5b0
rcu_do_batch+0x34e/0xd90
rcu_core+0x559/0xac0
__do_softirq+0x183/0x5a4
irq_exit_rcu+0x12d/0x170
sysvec_apic_timer_interrupt+0x6b/0x80
</IRQ>
<TASK>
asm_sysvec_apic_timer_interrupt+0x16/0x20
RIP: 0010:cpuidle_enter_state+0x175/0x300
Code: 30 00 0f 84 1f 01 00 00 83 e8 01 83 f8 ff 75 e5 48 83 c4 18 44 89 e8 5b 5d 41 5c 41 5d 41 5e 41 5f c3 cc cc cc cc fb 45 85 ed <0f> 89 60 ff ff ff 48 c1 e5 06 48 c7 43 18 00 00 00 00 48 83 44 2b
RSP: 0018:ffff888481cf7d90 EFLAGS: 00000202
RAX: 0000000000000000 RBX: ffff88887facddc8 RCX: 0000000000000000
RDX: 1ffff1110ff588b1 RSI: 0000000000000019 RDI: ffff88887fac4588
RBP: 0000000000000004 R08: 0000000000000002 R09: 0000000000043080
R10: 0009b02ea273363f R11: ffff88887fabf42b R12: ffffffff932592e0
R13: 0000000000000004 R14: 0000000000000000 R15: 00000022c880ec80
cpuidle_enter+0x4a/0xa0
do_idle+0x310/0x410
cpu_startup_entry+0x51/0x60
start_secondary+0x211/0x270
secondary_startup_64_no_verify+0x184/0x18b
</TASK>
Allocated by task 6853:
kasan_save_stack+0x1c/0x40
kasan_save_track+0x10/0x30
__kasan_kmalloc+0xa6/0xb0
__kmalloc+0x1eb/0x450
cipso_v4_sock_setattr+0x96/0x360
netlbl_sock_setattr+0x132/0x1f0
selinux_netlbl_socket_post_create+0x6c/0x110
selinux_socket_post_create+0x37b/0x7f0
security_socket_post_create+0x63/0xb0
__sock_create+0x305/0x450
__sys_socket_create.part.23+0xbd/0x130
__sys_socket+0x37/0xb0
__x64_sys_socket+0x6f/0xb0
do_syscall_64+0x83/0x160
entry_SYSCALL_64_after_hwframe+0x6e/0x76
Freed by task 6858:
kasan_save_stack+0x1c/0x40
kasan_save_track+0x10/0x30
kasan_save_free_info+0x3b/0x60
__kasan_slab_free+0x12c/0x1f0
kfree+0xed/0x2e0
inet_sock_destruct+0x54f/0x8b0
__sk_destruct+0x48/0x5b0
subflow_ulp_release+0x1f0/0x250
tcp_cleanup_ulp+0x6e/0x110
tcp_v4_destroy_sock+0x5a/0x3a0
inet_csk_destroy_sock+0x135/0x390
tcp_fin+0x416/0x5c0
tcp_data_queue+0x1bc8/0x4310
tcp_rcv_state_process+0x15a3/0x47b0
tcp_v4_do_rcv+0x2c1/0x990
tcp_v4_rcv+0x41fb/0x5ed0
ip_protocol_deliver_rcu+0x6d/0x9f0
ip_local_deliver_finish+0x278/0x360
ip_local_deliver+0x182/0x2c0
ip_rcv+0xb5/0x1c0
__netif_receive_skb_one_core+0x16e/0x1b0
process_backlog+0x1e3/0x650
__napi_poll+0xa6/0x500
net_rx_action+0x740/0xbb0
__do_softirq+0x183/0x5a4
The buggy address belongs to the object at ffff888485950880
which belongs to the cache kmalloc-64 of size 64
The buggy address is located 0 bytes inside of
64-byte region [ffff888485950880, ffff8884859508c0)
The buggy address belongs to the physical page:
page:0000000056d1e95e refcount:1 mapcount:0 mapping:0000000000000000 index:0xffff888485950700 pfn:0x485950
flags: 0x57ffffc0000800(slab|node=1|zone=2|lastcpupid=0x1fffff)
page_type: 0xffffffff()
raw: 0057ffffc0000800 ffff88810004c640 ffffea00121b8ac0 dead000000000006
raw: ffff888485950700 0000000000200019 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff888485950780: fa fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
ffff888485950800: fa fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
>ffff888485950880: fa fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
^
ffff888485950900: fa fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
ffff888485950980: 00 00 00 00 00 01 fc fc fc fc fc fc fc fc fc fc
Something similar (a refcount underflow) happens with CALIPSO/IPv6. Fix
this by duplicating IP / IPv6 options after clone, so that
ip{,6}_sock_destruct() doesn't end up freeing the same memory area twice.
Fixes: cf7da0d66c ("mptcp: Create SUBFLOW socket for incoming connections")
Cc: stable@vger.kernel.org
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://lore.kernel.org/r/20240223-upstream-net-20240223-misc-fixes-v1-8-162e87e48497@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b9cd26f640 upstream.
when inserting not contiguous data in the subflow write queue,
the protocol creates a new skb and prevent the TCP stack from
merging it later with already queued skbs by setting the EOR marker.
Still no push flag is explicitly set at the end of previous GSO
packet, making the aggregation on the receiver side sub-optimal -
and packetdrill self-tests less predictable.
Explicitly mark the end of not contiguous DSS with the push flag.
Fixes: 6d0060f600 ("mptcp: Write MPTCP DSS headers to outgoing data packets")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://lore.kernel.org/r/20240223-upstream-net-20240223-misc-fixes-v1-4-162e87e48497@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6890cb1ace upstream.
MKTME repurposes the high bit of physical address to key id for encryption
key and, even though MAXPHYADDR in CPUID[0x80000008] remains the same,
the valid bits in the MTRR mask register are based on the reduced number
of physical address bits.
detect_tme() in arch/x86/kernel/cpu/intel.c detects TME and subtracts
it from the total usable physical bits, but it is called too late.
Move the call to early_init_intel() so that it is called in setup_arch(),
before MTRRs are setup.
This fixes boot on TDX-enabled systems, which until now only worked with
"disable_mtrr_cleanup". Without the patch, the values written to the
MTRRs mask registers were 52-bit wide (e.g. 0x000fffff_80000800) and
the writes failed; with the patch, the values are 46-bit wide, which
matches the reduced MAXPHYADDR that is shown in /proc/cpuinfo.
Reported-by: Zixi Chen <zixchen@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc:stable@vger.kernel.org
Link: https://lore.kernel.org/all/20240131230902.1867092-3-pbonzini%40redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7fd817c906 upstream.
SETUP_RNG_SEED in setup_data is supplied by kexec and should
not be reserved in the e820 map.
Doing so reserves 16 bytes of RAM when booting with kexec.
(16 bytes because data->len is zeroed by parse_setup_data so only
sizeof(setup_data) is reserved.)
When kexec is used repeatedly, each boot adds two entries in the
kexec-provided e820 map as the 16-byte range splits a larger
range of usable memory. Eventually all of the 128 available entries
get used up. The next split will result in losing usable memory
as the new entries cannot be added to the e820 map.
Fixes: 68b8e9713c ("x86/setup: Use rng seeds from setup_data")
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: <stable@kernel.org>
Link: https://lore.kernel.org/r/ZbmOjKnARGiaYBd5@dwarf.suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a93c6cbd5 upstream.
Commit 'e3e56c050ab6 ("soc: qcom: rpmhpd: Make power_on actually enable
the domain")' aimed to make sure that a power-domain that is being
enabled without any particular performance-state requested will at least
turn the rail on, to avoid filling DeviceTree with otherwise unnecessary
required-opps properties.
But in the event that aggregation happens on a disabled power-domain, with
an enabled peer without performance-state, both the local and peer
corner are 0. The peer's enabled_corner is not considered, with the
result that the underlying (shared) resource is disabled.
One case where this can be observed is when the display stack keeps mmcx
enabled (but without a particular performance-state vote) in order to
access registers and sync_state happens in the rpmhpd driver. As mmcx_ao
is flushed the state of the peer (mmcx) is not considered and mmcx_ao
ends up turning off "mmcx.lvl" underneath mmcx. This has been observed
several times, but has been painted over in DeviceTree by adding an
explicit vote for the lowest non-disabled performance-state.
Fixes: e3e56c050a ("soc: qcom: rpmhpd: Make power_on actually enable the domain")
Reported-by: Johan Hovold <johan@kernel.org>
Closes: https://lore.kernel.org/linux-arm-msm/ZdMwZa98L23mu3u6@hovoldconsulting.com/
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240226-rpmhpd-enable-corner-fix-v1-1-68c004cec48c@quicinc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f45812cc23 upstream.
Work around a quirk in a few old (2011-ish) UEFI implementations, where
a call to `GetNextVariableName` with a buffer size larger than 512 bytes
will always return EFI_INVALID_PARAMETER.
There is some lore around EFI variable names being up to 1024 bytes in
size, but this has no basis in the UEFI specification, and the upper
bounds are typically platform specific, and apply to the entire variable
(name plus payload).
Given that Linux does not permit creating files with names longer than
NAME_MAX (255) bytes, 512 bytes (== 256 UTF-16 characters) is a
reasonable limit.
Cc: <stable@vger.kernel.org> # 6.1+
Signed-off-by: Tim Schumacher <timschumi@gmx.de>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aeb004c0cd upstream.
Syzkaller reported the following WARN_ON:
WARNING: CPU: 1 PID: 4738 at drivers/iommu/iommufd/io_pagetable.c:1360
Call Trace:
iommufd_access_change_ioas+0x2fe/0x4e0
iommufd_access_destroy_object+0x50/0xb0
iommufd_object_remove+0x2a3/0x490
iommufd_object_destroy_user
iommufd_access_destroy+0x71/0xb0
iommufd_test_staccess_release+0x89/0xd0
__fput+0x272/0xb50
__fput_sync+0x4b/0x60
__do_sys_close
__se_sys_close
__x64_sys_close+0x8b/0x110
do_syscall_x64
The mismatch between the access pointer in the list and the passed-in
pointer is resulting from an overwrite of access->iopt_access_list_id, in
iopt_add_access(). Called from iommufd_access_change_ioas() when
xa_alloc() succeeds but iopt_calculate_iova_alignment() fails.
Add a new_id in iopt_add_access() and only update iopt_access_list_id when
returning successfully.
Cc: stable@vger.kernel.org
Fixes: 9227da7816 ("iommufd: Add iommufd_access_change_ioas(_id) helpers")
Link: https://lore.kernel.org/r/2dda7acb25b8562ec5f1310de828ef5da9ef509c.1708636627.git.nicolinc@nvidia.com
Reported-by: Jason Gunthorpe <jgg@nvidia.com>
Suggested-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Nicolin Chen <nicolinc@nvidia.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 680341382d upstream.
CALLER_ADDRx returns caller's address at specified level, they are used
for several tracers. These macros eventually use
__builtin_return_address(n) to get the caller's address if arch doesn't
define their own implementation.
In RISC-V, __builtin_return_address(n) only works when n == 0, we need
to walk the stack frame to get the caller's address at specified level.
data.level started from 'level + 3' due to the call flow of getting
caller's address in RISC-V implementation. If we don't have additional
three iteration, the level is corresponding to follows:
callsite -> return_address -> arch_stack_walk -> walk_stackframe
| | | |
level 3 level 2 level 1 level 0
Fixes: 10626c32e3 ("riscv/ftrace: Add basic support")
Cc: stable@vger.kernel.org
Reviewed-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Signed-off-by: Zong Li <zong.li@sifive.com>
Link: https://lore.kernel.org/r/20240202015102.26251-1-zong.li@sifive.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3aff0c459e upstream.
Commit e4bb020f3d ("riscv: detect assembler support for .option arch")
added two tests, one for a valid value to '.option arch' that should
succeed and one for an invalid value that is expected to fail to make
sure that support for '.option arch' is properly detected because Clang
does not error when '.option arch' is not supported:
$ clang --target=riscv64-linux-gnu -Werror -x assembler -c -o /dev/null <(echo '.option arch, +m')
/dev/fd/63:1:9: warning: unknown option, expected 'push', 'pop', 'rvc', 'norvc', 'relax' or 'norelax'
.option arch, +m
^
$ echo $?
0
Unfortunately, the invalid test started being accepted by Clang after
the linked llvm-project change, which causes CONFIG_AS_HAS_OPTION_ARCH
and configurations that depend on it to be silently disabled, even
though those versions do support '.option arch'.
The invalid test can be avoided altogether by using
'-Wa,--fatal-warnings', which will turn all assembler warnings into
errors, like '-Werror' does for the compiler:
$ clang --target=riscv64-linux-gnu -Werror -Wa,--fatal-warnings -x assembler -c -o /dev/null <(echo '.option arch, +m')
/dev/fd/63:1:9: error: unknown option, expected 'push', 'pop', 'rvc', 'norvc', 'relax' or 'norelax'
.option arch, +m
^
$ echo $?
1
The as-instr macros have been updated to make use of this flag, so
remove the invalid test, which allows CONFIG_AS_HAS_OPTION_ARCH to work
for all compiler versions.
Cc: stable@vger.kernel.org
Fixes: e4bb020f3d ("riscv: detect assembler support for .option arch")
Link: 3ac9fe69f7
Reported-by: Eric Biggers <ebiggers@kernel.org>
Closes: https://lore.kernel.org/r/20240121011341.GA97368@sol.localdomain/
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Tested-by: Eric Biggers <ebiggers@google.com>
Tested-by: Andy Chiu <andybnac@gmail.com>
Reviewed-by: Andy Chiu <andybnac@gmail.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Masahiro Yamada <masahiroy@kernel.org>
Link: https://lore.kernel.org/r/20240125-fix-riscv-option-arch-llvm-18-v1-2-390ac9cc3cd0@kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff3206d218 upstream.
Initializing an eMMC that's connected via a 1-bit bus is current failing,
if the HW (DT) informs that 4-bit bus is supported. In fact this is a
regression, as we were earlier capable of falling back to 1-bit mode, when
switching to 4/8-bit bus failed. Therefore, let's restore the behaviour.
Log for Samsung eMMC 5.1 chip connected via 1bit bus (only D0 pin)
Before patch:
[134509.044225] mmc0: switch to bus width 4 failed
[134509.044509] mmc0: new high speed MMC card at address 0001
[134509.054594] mmcblk0: mmc0:0001 BGUF4R 29.1 GiB
[134509.281602] mmc0: switch to bus width 4 failed
[134509.282638] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.282657] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[134509.284598] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.284602] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[134509.284609] ldm_validate_partition_table(): Disk read failed.
[134509.286495] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.286500] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[134509.288303] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.288308] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[134509.289540] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.289544] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[134509.289553] mmcblk0: unable to read partition table
[134509.289728] mmcblk0boot0: mmc0:0001 BGUF4R 31.9 MiB
[134509.290283] mmcblk0boot1: mmc0:0001 BGUF4R 31.9 MiB
[134509.294577] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2
[134509.295835] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.295841] Buffer I/O error on dev mmcblk0, logical block 0, async page read
After patch:
[134551.089613] mmc0: switch to bus width 4 failed
[134551.090377] mmc0: new high speed MMC card at address 0001
[134551.102271] mmcblk0: mmc0:0001 BGUF4R 29.1 GiB
[134551.113365] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 p19 p20 p21
[134551.114262] mmcblk0boot0: mmc0:0001 BGUF4R 31.9 MiB
[134551.114925] mmcblk0boot1: mmc0:0001 BGUF4R 31.9 MiB
Fixes: 577fb13199 ("mmc: rework selection of bus speed mode")
Cc: stable@vger.kernel.org
Signed-off-by: Ivan Semenov <ivan@semenov.dev>
Link: https://lore.kernel.org/r/20240206172845.34316-1-ivan@semenov.dev
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b1ba3f904 upstream.
Turning on CONFIG_DMA_API_DEBUG_SG results in the following warning:
DMA-API: mmci-pl18x 48220000.mmc: cacheline tracking EEXIST,
overlapping mappings aren't supported
WARNING: CPU: 1 PID: 51 at kernel/dma/debug.c:568
add_dma_entry+0x234/0x2f4
Modules linked in:
CPU: 1 PID: 51 Comm: kworker/1:2 Not tainted 6.1.28 #1
Hardware name: STMicroelectronics STM32MP257F-EV1 Evaluation Board (DT)
Workqueue: events_freezable mmc_rescan
Call trace:
add_dma_entry+0x234/0x2f4
debug_dma_map_sg+0x198/0x350
__dma_map_sg_attrs+0xa0/0x110
dma_map_sg_attrs+0x10/0x2c
sdmmc_idma_prep_data+0x80/0xc0
mmci_prep_data+0x38/0x84
mmci_start_data+0x108/0x2dc
mmci_request+0xe4/0x190
__mmc_start_request+0x68/0x140
mmc_start_request+0x94/0xc0
mmc_wait_for_req+0x70/0x100
mmc_send_tuning+0x108/0x1ac
sdmmc_execute_tuning+0x14c/0x210
mmc_execute_tuning+0x48/0xec
mmc_sd_init_uhs_card.part.0+0x208/0x464
mmc_sd_init_card+0x318/0x89c
mmc_attach_sd+0xe4/0x180
mmc_rescan+0x244/0x320
DMA API debug brings to light leaking dma-mappings as dma_map_sg and
dma_unmap_sg are not correctly balanced.
If an error occurs in mmci_cmd_irq function, only mmci_dma_error
function is called and as this API is not managed on stm32 variant,
dma_unmap_sg is never called in this error path.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Fixes: 46b723dd86 ("mmc: mmci: add stm32 sdmmc variant")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240207143951.938144-1-christophe.kerello@foss.st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 87a39071e0 upstream.
Initialize the qDMA irqs after the registers are configured so that
interrupts that may have been pending from a primary kernel don't get
processed by the irq handler before it is ready to and cause panic with
the following trace:
Call trace:
fsl_qdma_queue_handler+0xf8/0x3e8
__handle_irq_event_percpu+0x78/0x2b0
handle_irq_event_percpu+0x1c/0x68
handle_irq_event+0x44/0x78
handle_fasteoi_irq+0xc8/0x178
generic_handle_irq+0x24/0x38
__handle_domain_irq+0x90/0x100
gic_handle_irq+0x5c/0xb8
el1_irq+0xb8/0x180
_raw_spin_unlock_irqrestore+0x14/0x40
__setup_irq+0x4bc/0x798
request_threaded_irq+0xd8/0x190
devm_request_threaded_irq+0x74/0xe8
fsl_qdma_probe+0x4d4/0xca8
platform_drv_probe+0x50/0xa0
really_probe+0xe0/0x3f8
driver_probe_device+0x64/0x130
device_driver_attach+0x6c/0x78
__driver_attach+0xbc/0x158
bus_for_each_dev+0x5c/0x98
driver_attach+0x20/0x28
bus_add_driver+0x158/0x220
driver_register+0x60/0x110
__platform_driver_register+0x44/0x50
fsl_qdma_driver_init+0x18/0x20
do_one_initcall+0x48/0x258
kernel_init_freeable+0x1a4/0x23c
kernel_init+0x10/0xf8
ret_from_fork+0x10/0x18
Cc: stable@vger.kernel.org
Fixes: b092529e0a ("dmaengine: fsl-qdma: Add qDMA controller driver for Layerscape SoCs")
Signed-off-by: Curtis Klein <curtis.klein@hpe.com>
Signed-off-by: Yi Zhao <yi.zhao@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240201220406.440145-1-Frank.Li@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df2515a179 upstream.
The PTDMA driver sets DMA masks in two different places for the same
device inconsistently. First call is in pt_pci_probe(), where it uses
48bit mask. The second call is in pt_dmaengine_register(), where it
uses a 64bit mask. Using 64bit dma mask causes IO_PAGE_FAULT errors
on DMA transfers between main memory and other devices.
Without the extra call it works fine. Additionally the second call
doesn't check the return value so it can silently fail.
Remove the superfluous dma_set_mask() call and only use 48bit mask.
Cc: stable@vger.kernel.org
Fixes: b0b4a6b105 ("dmaengine: ptdma: register PTDMA controller as a DMA resource")
Reviewed-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Tadeusz Struk <tstruk@gigaio.com>
Link: https://lore.kernel.org/r/20240222163053.13842-1-tstruk@gigaio.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c0cf6d196 upstream.
The bit-sliced implementation of AES-CTR operates on blocks of 128
bytes, and will fall back to the plain NEON version for tail blocks or
inputs that are shorter than 128 bytes to begin with.
It will call straight into the plain NEON asm helper, which performs all
memory accesses in granules of 16 bytes (the size of a NEON register).
For this reason, the associated plain NEON glue code will copy inputs
shorter than 16 bytes into a temporary buffer, given that this is a rare
occurrence and it is not worth the effort to work around this in the asm
code.
The fallback from the bit-sliced NEON version fails to take this into
account, potentially resulting in out-of-bounds accesses. So clone the
same workaround, and use a temp buffer for short in/outputs.
Fixes: fc074e1300 ("crypto: arm64/aes-neonbs-ctr - fallback to plain NEON for final chunk")
Cc: <stable@vger.kernel.org>
Reported-by: syzbot+f1ceaa1a09ab891e1934@syzkaller.appspotmail.com
Reviewed-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9d739bccf2 upstream.
There is chip (ls1028a) errata:
The SoC may hang on 16 byte unaligned read transactions by QDMA.
Unaligned read transactions initiated by QDMA may stall in the NOC
(Network On-Chip), causing a deadlock condition. Stalled transactions will
trigger completion timeouts in PCIe controller.
Workaround:
Enable prefetch by setting the source descriptor prefetchable bit
( SD[PF] = 1 ).
Implement this workaround.
Cc: stable@vger.kernel.org
Fixes: b092529e0a ("dmaengine: fsl-qdma: Add qDMA controller driver for Layerscape SoCs")
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240201215007.439503-1-Frank.Li@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5897710b28 upstream.
If we have a sparse file with a trailing hole (from the last extent's end
to i_size) and then create an extent in the file that ends before the
file's i_size, then when doing an incremental send we will issue a write
full of zeroes for the range that starts immediately after the new extent
ends up to i_size. While this isn't incorrect because the file ends up
with exactly the same data, it unnecessarily results in using extra space
at the destination with one or more extents full of zeroes instead of
having a hole. In same cases this results in using megabytes or even
gigabytes of unnecessary space.
Example, reproducer:
$ cat test.sh
#!/bin/bash
DEV=/dev/sdh
MNT=/mnt/sdh
mkfs.btrfs -f $DEV
mount $DEV $MNT
# Create 1G sparse file.
xfs_io -f -c "truncate 1G" $MNT/foobar
# Create base snapshot.
btrfs subvolume snapshot -r $MNT $MNT/mysnap1
# Create send stream (full send) for the base snapshot.
btrfs send -f /tmp/1.snap $MNT/mysnap1
# Now write one extent at the beginning of the file and one somewhere
# in the middle, leaving a gap between the end of this second extent
# and the file's size.
xfs_io -c "pwrite -S 0xab 0 128K" \
-c "pwrite -S 0xcd 512M 128K" \
$MNT/foobar
# Now create a second snapshot which is going to be used for an
# incremental send operation.
btrfs subvolume snapshot -r $MNT $MNT/mysnap2
# Create send stream (incremental send) for the second snapshot.
btrfs send -p $MNT/mysnap1 -f /tmp/2.snap $MNT/mysnap2
# Now recreate the filesystem by receiving both send streams and
# verify we get the same content that the original filesystem had
# and file foobar has only two extents with a size of 128K each.
umount $MNT
mkfs.btrfs -f $DEV
mount $DEV $MNT
btrfs receive -f /tmp/1.snap $MNT
btrfs receive -f /tmp/2.snap $MNT
echo -e "\nFile fiemap in the second snapshot:"
# Should have:
#
# 128K extent at file range [0, 128K[
# hole at file range [128K, 512M[
# 128K extent file range [512M, 512M + 128K[
# hole at file range [512M + 128K, 1G[
xfs_io -r -c "fiemap -v" $MNT/mysnap2/foobar
# File should be using 256K of data (two 128K extents).
echo -e "\nSpace used by the file: $(du -h $MNT/mysnap2/foobar | cut -f 1)"
umount $MNT
Running the test, we can see with fiemap that we get an extent for the
range [512M, 1G[, while in the source filesystem we have an extent for
the range [512M, 512M + 128K[ and a hole for the rest of the file (the
range [512M + 128K, 1G[):
$ ./test.sh
(...)
File fiemap in the second snapshot:
/mnt/sdh/mysnap2/foobar:
EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS
0: [0..255]: 26624..26879 256 0x0
1: [256..1048575]: hole 1048320
2: [1048576..2097151]: 2156544..3205119 1048576 0x1
Space used by the file: 513M
This happens because once we finish processing an inode, at
finish_inode_if_needed(), we always issue a hole (write operations full
of zeros) if there's a gap between the end of the last processed extent
and the file's size, even if that range is already a hole in the parent
snapshot. Fix this by issuing the hole only if the range is not already
a hole.
After this change, running the test above, we get the expected layout:
$ ./test.sh
(...)
File fiemap in the second snapshot:
/mnt/sdh/mysnap2/foobar:
EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS
0: [0..255]: 26624..26879 256 0x0
1: [256..1048575]: hole 1048320
2: [1048576..1048831]: 26880..27135 256 0x1
3: [1048832..2097151]: hole 1048320
Space used by the file: 256K
A test case for fstests will follow soon.
CC: stable@vger.kernel.org # 6.1+
Reported-by: Dorai Ashok S A <dash.btrfs@inix.me>
Link: https://lore.kernel.org/linux-btrfs/c0bf7818-9c45-46a8-b3d3-513230d0c86e@inix.me/
Reviewed-by: Sweet Tea Dorminy <sweettea-kernel@dorminy.me>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e2b54eaf28 upstream.
When creating a snapshot we may do a double free of an anonymous device
in case there's an error committing the transaction. The second free may
result in freeing an anonymous device number that was allocated by some
other subsystem in the kernel or another btrfs filesystem.
The steps that lead to this:
1) At ioctl.c:create_snapshot() we allocate an anonymous device number
and assign it to pending_snapshot->anon_dev;
2) Then we call btrfs_commit_transaction() and end up at
transaction.c:create_pending_snapshot();
3) There we call btrfs_get_new_fs_root() and pass it the anonymous device
number stored in pending_snapshot->anon_dev;
4) btrfs_get_new_fs_root() frees that anonymous device number because
btrfs_lookup_fs_root() returned a root - someone else did a lookup
of the new root already, which could some task doing backref walking;
5) After that some error happens in the transaction commit path, and at
ioctl.c:create_snapshot() we jump to the 'fail' label, and after
that we free again the same anonymous device number, which in the
meanwhile may have been reallocated somewhere else, because
pending_snapshot->anon_dev still has the same value as in step 1.
Recently syzbot ran into this and reported the following trace:
------------[ cut here ]------------
ida_free called for id=51 which is not allocated.
WARNING: CPU: 1 PID: 31038 at lib/idr.c:525 ida_free+0x370/0x420 lib/idr.c:525
Modules linked in:
CPU: 1 PID: 31038 Comm: syz-executor.2 Not tainted 6.8.0-rc4-syzkaller-00410-gc02197fc9076 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/25/2024
RIP: 0010:ida_free+0x370/0x420 lib/idr.c:525
Code: 10 42 80 3c 28 (...)
RSP: 0018:ffffc90015a67300 EFLAGS: 00010246
RAX: be5130472f5dd000 RBX: 0000000000000033 RCX: 0000000000040000
RDX: ffffc90009a7a000 RSI: 000000000003ffff RDI: 0000000000040000
RBP: ffffc90015a673f0 R08: ffffffff81577992 R09: 1ffff92002b4cdb4
R10: dffffc0000000000 R11: fffff52002b4cdb5 R12: 0000000000000246
R13: dffffc0000000000 R14: ffffffff8e256b80 R15: 0000000000000246
FS: 00007fca3f4b46c0(0000) GS:ffff8880b9500000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f167a17b978 CR3: 000000001ed26000 CR4: 0000000000350ef0
Call Trace:
<TASK>
btrfs_get_root_ref+0xa48/0xaf0 fs/btrfs/disk-io.c:1346
create_pending_snapshot+0xff2/0x2bc0 fs/btrfs/transaction.c:1837
create_pending_snapshots+0x195/0x1d0 fs/btrfs/transaction.c:1931
btrfs_commit_transaction+0xf1c/0x3740 fs/btrfs/transaction.c:2404
create_snapshot+0x507/0x880 fs/btrfs/ioctl.c:848
btrfs_mksubvol+0x5d0/0x750 fs/btrfs/ioctl.c:998
btrfs_mksnapshot+0xb5/0xf0 fs/btrfs/ioctl.c:1044
__btrfs_ioctl_snap_create+0x387/0x4b0 fs/btrfs/ioctl.c:1306
btrfs_ioctl_snap_create_v2+0x1ca/0x400 fs/btrfs/ioctl.c:1393
btrfs_ioctl+0xa74/0xd40
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:871 [inline]
__se_sys_ioctl+0xfe/0x170 fs/ioctl.c:857
do_syscall_64+0xfb/0x240
entry_SYSCALL_64_after_hwframe+0x6f/0x77
RIP: 0033:0x7fca3e67dda9
Code: 28 00 00 00 (...)
RSP: 002b:00007fca3f4b40c8 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
RAX: ffffffffffffffda RBX: 00007fca3e7abf80 RCX: 00007fca3e67dda9
RDX: 00000000200005c0 RSI: 0000000050009417 RDI: 0000000000000003
RBP: 00007fca3e6ca47a R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 000000000000000b R14: 00007fca3e7abf80 R15: 00007fff6bf95658
</TASK>
Where we get an explicit message where we attempt to free an anonymous
device number that is not currently allocated. It happens in a different
code path from the example below, at btrfs_get_root_ref(), so this change
may not fix the case triggered by syzbot.
To fix at least the code path from the example above, change
btrfs_get_root_ref() and its callers to receive a dev_t pointer argument
for the anonymous device number, so that in case it frees the number, it
also resets it to 0, so that up in the call chain we don't attempt to do
the double free.
CC: stable@vger.kernel.org # 5.10+
Link: https://lore.kernel.org/linux-btrfs/000000000000f673a1061202f630@google.com/
Fixes: e03ee2fe87 ("btrfs: do not ASSERT() if the newly created subvolume already got read")
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f78c137533 upstream.
It's currently possible to change the mesh ID when the
interface isn't yet in mesh mode, at the same time as
changing it into mesh mode. This leads to an overwrite
of data in the wdev->u union for the interface type it
currently has, causing cfg80211_change_iface() to do
wrong things when switching.
We could probably allow setting an interface to mesh
while setting the mesh ID at the same time by doing a
different order of operations here, but realistically
there's no userspace that's going to do this, so just
disallow changes in iftype when setting mesh ID.
Cc: stable@vger.kernel.org
Fixes: 29cbe68c51 ("cfg80211/mac80211: add mesh join/leave commands")
Reported-by: syzbot+dd4779978217b1973180@syzkaller.appspotmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e6a30d0c48 upstream.
The check in nand_base.c, nand_scan_tail() : has the following code:
(ecc->steps * ecc->size != mtd->writesize) which fails for some NAND chips.
Remove ECC entries in this driver which are not integral multiplications,
and adjust the number of chunks for entries which fails the above
calculation so it will calculate correctly (this was previously done
automatically before the check and was removed in a later commit).
Fixes: 68c18dae68 ("mtd: rawnand: marvell: add missing layouts")
Cc: stable@vger.kernel.org
Signed-off-by: Elad Nachman <enachman@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a75cb05d5 upstream.
In cachestat, we access the folio from the page cache's xarray to compute
its page offset, and check for its dirty and writeback flags. However, we
do not hold a reference to the folio before performing these actions,
which means the folio can concurrently be released and reused as another
folio/page/slab.
Get around this altogether by just using xarray's existing machinery for
the folio page offsets and dirty/writeback states.
This changes behavior for tmpfs files to now always report zeroes in their
dirty and writeback counters. This is okay as tmpfs doesn't follow
conventional writeback cache behavior: its pages get "cleaned" during
swapout, after which they're no longer resident etc.
Link: https://lkml.kernel.org/r/20240220153409.GA216065@cmpxchg.org
Fixes: cf264e1329 ("cachestat: implement cachestat syscall")
Reported-by: Jann Horn <jannh@google.com>
Suggested-by: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Nhat Pham <nphamcs@gmail.com>
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Tested-by: Jann Horn <jannh@google.com>
Cc: <stable@vger.kernel.org> [6.4+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d9818b3e90 upstream.
When linking or renaming a file, if only one of the source or
destination directory is backed by an S_PRIVATE inode, then the related
set of layer masks would be used as uninitialized by
is_access_to_paths_allowed(). This would result to indeterministic
access for one side instead of always being allowed.
This bug could only be triggered with a mounted filesystem containing
both S_PRIVATE and !S_PRIVATE inodes, which doesn't seem possible.
The collect_domain_accesses() calls return early if
is_nouser_or_private() returns false, which means that the directory's
superblock has SB_NOUSER or its inode has S_PRIVATE. Because rename or
link actions are only allowed on the same mounted filesystem, the
superblock is always the same for both source and destination
directories. However, it might be possible in theory to have an
S_PRIVATE parent source inode with an !S_PRIVATE parent destination
inode, or vice versa.
To make sure this case is not an issue, explicitly initialized both set
of layer masks to 0, which means to allow all actions on the related
side. If at least on side has !S_PRIVATE, then
collect_domain_accesses() and is_access_to_paths_allowed() check for the
required access rights.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Günther Noack <gnoack@google.com>
Cc: Jann Horn <jannh@google.com>
Cc: Shervin Oloumi <enlightened@chromium.org>
Cc: stable@vger.kernel.org
Fixes: b91c3e4ea7 ("landlock: Add support for file reparenting with LANDLOCK_ACCESS_FS_REFER")
Link: https://lore.kernel.org/r/20240219190345.2928627-1-mic@digikod.net
Signed-off-by: Mickaël Salaün <mic@digikod.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c17d2a7b21 upstream.
A recent commit restored the original (and still documented) semantics
for the HCI_QUIRK_USE_BDADDR_PROPERTY quirk so that the device address
is considered invalid unless an address is provided by firmware.
This specifically means that this flag must only be set for devices with
invalid addresses, but the Broadcom BCM4377 driver has so far been
setting this flag unconditionally.
Fortunately the driver already checks for invalid addresses during setup
and sets the HCI_QUIRK_INVALID_BDADDR flag, which can simply be replaced
with HCI_QUIRK_USE_BDADDR_PROPERTY to indicate that the default address
is invalid but can be overridden by firmware (long term, this should
probably just always be allowed).
Fixes: 6945795bc8 ("Bluetooth: fix use-bdaddr-property quirk")
Cc: stable@vger.kernel.org # 6.5
Reported-by: Felix Zhang <mrman@mrman314.tech>
Link: https://lore.kernel.org/r/77419ffacc5b4875e920e038332575a2a5bff29f.camel@mrman314.tech/
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reported-by: Felix Zhang <mrman@mrman314.tech>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1fdf4e8be7 upstream.
On my EliteBook 840 G8 Notebook PC (ProdId 5S7R6EC#ABD; built 2022 for
german market) the Mute LED is always on. The mute button itself works
as expected. alsa-info.sh shows a different subsystem-id 0x8ab9 for
Realtek ALC285 Codec, thus the existing quirks for HP 840 G8 don't work.
Therefore, add a new quirk for this type of EliteBook.
Signed-off-by: Hans Peter <flurry123@gmx.ch>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20240219164518.4099-1-flurry123@gmx.ch
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a1a4a9ca77 ]
For fiemap we recently stopped locking the target extent range for the
whole duration of the fiemap call, in order to avoid a deadlock in a
scenario where the fiemap buffer happens to be a memory mapped range of
the same file. This use case is very unlikely to be useful in practice but
it may be triggered by fuzz testing (syzbot, etc).
However by not locking the target extent range for the whole duration of
the fiemap call we can race with an ordered extent. This happens like
this:
1) The fiemap task finishes processing a file extent item that covers
the file range [512K, 1M[, and that file extent item is the last item
in the leaf currently being processed;
2) And ordered extent for the file range [768K, 2M[, in COW mode,
completes (btrfs_finish_one_ordered()) and the file extent item
covering the range [512K, 1M[ is trimmed to cover the range
[512K, 768K[ and then a new file extent item for the range [768K, 2M[
is inserted in the inode's subvolume tree;
3) The fiemap task calls fiemap_next_leaf_item(), which then calls
btrfs_next_leaf() to find the next leaf / item. This finds that the
the next key following the one we previously processed (its type is
BTRFS_EXTENT_DATA_KEY and its offset is 512K), is the key corresponding
to the new file extent item inserted by the ordered extent, which has
a type of BTRFS_EXTENT_DATA_KEY and an offset of 768K;
4) Later the fiemap code ends up at emit_fiemap_extent() and triggers
the warning:
if (cache->offset + cache->len > offset) {
WARN_ON(1);
return -EINVAL;
}
Since we get 1M > 768K, because the previously emitted entry for the
old extent covering the file range [512K, 1M[ ends at an offset that
is greater than the new extent's start offset (768K). This makes fiemap
fail with -EINVAL besides triggering the warning that produces a stack
trace like the following:
[1621.677651] ------------[ cut here ]------------
[1621.677656] WARNING: CPU: 1 PID: 204366 at fs/btrfs/extent_io.c:2492 emit_fiemap_extent+0x84/0x90 [btrfs]
[1621.677899] Modules linked in: btrfs blake2b_generic (...)
[1621.677951] CPU: 1 PID: 204366 Comm: pool Not tainted 6.8.0-rc5-btrfs-next-151+ #1
[1621.677954] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.2-0-gea1b7a073390-prebuilt.qemu.org 04/01/2014
[1621.677956] RIP: 0010:emit_fiemap_extent+0x84/0x90 [btrfs]
[1621.678033] Code: 2b 4c 89 63 (...)
[1621.678035] RSP: 0018:ffffab16089ffd20 EFLAGS: 00010206
[1621.678037] RAX: 00000000004fa000 RBX: ffffab16089ffe08 RCX: 0000000000009000
[1621.678039] RDX: 00000000004f9000 RSI: 00000000004f1000 RDI: ffffab16089ffe90
[1621.678040] RBP: 00000000004f9000 R08: 0000000000001000 R09: 0000000000000000
[1621.678041] R10: 0000000000000000 R11: 0000000000001000 R12: 0000000041d78000
[1621.678043] R13: 0000000000001000 R14: 0000000000000000 R15: ffff9434f0b17850
[1621.678044] FS: 00007fa6e20006c0(0000) GS:ffff943bdfa40000(0000) knlGS:0000000000000000
[1621.678046] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[1621.678048] CR2: 00007fa6b0801000 CR3: 000000012d404002 CR4: 0000000000370ef0
[1621.678053] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[1621.678055] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[1621.678056] Call Trace:
[1621.678074] <TASK>
[1621.678076] ? __warn+0x80/0x130
[1621.678082] ? emit_fiemap_extent+0x84/0x90 [btrfs]
[1621.678159] ? report_bug+0x1f4/0x200
[1621.678164] ? handle_bug+0x42/0x70
[1621.678167] ? exc_invalid_op+0x14/0x70
[1621.678170] ? asm_exc_invalid_op+0x16/0x20
[1621.678178] ? emit_fiemap_extent+0x84/0x90 [btrfs]
[1621.678253] extent_fiemap+0x766/0xa30 [btrfs]
[1621.678339] btrfs_fiemap+0x45/0x80 [btrfs]
[1621.678420] do_vfs_ioctl+0x1e4/0x870
[1621.678431] __x64_sys_ioctl+0x6a/0xc0
[1621.678434] do_syscall_64+0x52/0x120
[1621.678445] entry_SYSCALL_64_after_hwframe+0x6e/0x76
There's also another case where before calling btrfs_next_leaf() we are
processing a hole or a prealloc extent and we had several delalloc ranges
within that hole or prealloc extent. In that case if the ordered extents
complete before we find the next key, we may end up finding an extent item
with an offset smaller than (or equals to) the offset in cache->offset.
So fix this by changing emit_fiemap_extent() to address these three
scenarios like this:
1) For the first case, steps listed above, adjust the length of the
previously cached extent so that it does not overlap with the current
extent, emit the previous one and cache the current file extent item;
2) For the second case where he had a hole or prealloc extent with
multiple delalloc ranges inside the hole or prealloc extent's range,
and the current file extent item has an offset that matches the offset
in the fiemap cache, just discard what we have in the fiemap cache and
assign the current file extent item to the cache, since it's more up
to date;
3) For the third case where he had a hole or prealloc extent with
multiple delalloc ranges inside the hole or prealloc extent's range
and the offset of the file extent item we just found is smaller than
what we have in the cache, just skip the current file extent item
if its range end at or behind the cached extent's end, because we may
have emitted (to the fiemap user space buffer) delalloc ranges that
overlap with the current file extent item's range. If the file extent
item's range goes beyond the end offset of the cached extent, just
emit the cached extent and cache a subrange of the file extent item,
that goes from the end offset of the cached extent to the end offset
of the file extent item.
Dealing with those cases in those ways makes everything consistent by
reflecting the current state of file extent items in the btree and
without emitting extents that have overlapping ranges (which would be
confusing and violating expectations).
This issue could be triggered often with test case generic/561, and was
also hit and reported by Wang Yugui.
Reported-by: Wang Yugui <wangyugui@e16-tech.com>
Link: https://lore.kernel.org/linux-btrfs/20240223104619.701F.409509F4@e16-tech.com/
Fixes: b0ad381fa7 ("btrfs: fix deadlock with fiemap and extent locking")
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 16ab4646c9 ]
This reverts commit ce173474cf.
We cannot correctly deal with NAPOT mappings in vmalloc/vmap because if
some part of a NAPOT mapping is unmapped, the remaining mapping is not
updated accordingly. For example:
ptr = vmalloc_huge(64 * 1024, GFP_KERNEL);
vunmap_range((unsigned long)(ptr + PAGE_SIZE),
(unsigned long)(ptr + 64 * 1024));
leads to the following kernel page table dump:
0xffff8f8000ef0000-0xffff8f8000ef1000 0x00000001033c0000 4K PTE N .. .. D A G . . W R V
Meaning the first entry which was not unmapped still has the N bit set,
which, if accessed first and cached in the TLB, could allow access to the
unmapped range.
That's because the logic to break the NAPOT mapping does not exist and
likely won't. Indeed, to break a NAPOT mapping, we first have to clear
the whole mapping, flush the TLB and then set the new mapping ("break-
before-make" equivalent). That works fine in userspace since we can handle
any pagefault occurring on the remaining mapping but we can't handle a kernel
pagefault on such mapping.
So fix this by reverting the commit that introduced the vmap/vmalloc
support.
Fixes: ce173474cf ("riscv: mm: support Svnapot in huge vmap")
Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Link: https://lore.kernel.org/r/20240227205016.121901-2-alexghiti@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f7a076466 ]
If a directory has a block with only ".__afsXXXX" files in it (from
uncompleted silly-rename), these .__afsXXXX files are skipped but without
advancing the file position in the dir_context. This leads to
afs_dir_iterate() repeating the block again and again.
Fix this by making the code that skips the .__afsXXXX file also manually
advance the file position.
The symptoms are a soft lookup:
watchdog: BUG: soft lockup - CPU#3 stuck for 52s! [check:5737]
...
RIP: 0010:afs_dir_iterate_block+0x39/0x1fd
...
? watchdog_timer_fn+0x1a6/0x213
...
? asm_sysvec_apic_timer_interrupt+0x16/0x20
? afs_dir_iterate_block+0x39/0x1fd
afs_dir_iterate+0x10a/0x148
afs_readdir+0x30/0x4a
iterate_dir+0x93/0xd3
__do_sys_getdents64+0x6b/0xd4
This is almost certainly the actual fix for:
https://bugzilla.kernel.org/show_bug.cgi?id=218496
Fixes: 57e9d49c54 ("afs: Hide silly-rename files from userspace")
Signed-off-by: David Howells <dhowells@redhat.com>
Link: https://lore.kernel.org/r/786185.1708694102@warthog.procyon.org.uk
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: Markus Suvanto <markus.suvanto@gmail.com>
cc: linux-afs@lists.infradead.org
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 00d6a284fc ]
Commit a5a923038d (fbdev: fbcon: Properly revert changes when
vc_resize() failed) started restoring old font data upon failure (of
vc_resize()). But it performs so only for user fonts. It means that the
"system"/internal fonts are not restored at all. So in result, the very
first call to fbcon_do_set_font() performs no restore at all upon
failing vc_resize().
This can be reproduced by Syzkaller to crash the system on the next
invocation of font_get(). It's rather hard to hit the allocation failure
in vc_resize() on the first font_set(), but not impossible. Esp. if
fault injection is used to aid the execution/failure. It was
demonstrated by Sirius:
BUG: unable to handle page fault for address: fffffffffffffff8
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD cb7b067 P4D cb7b067 PUD cb7d067 PMD 0
Oops: 0000 [#1] PREEMPT SMP KASAN
CPU: 1 PID: 8007 Comm: poc Not tainted 6.7.0-g9d1694dc91ce #20
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014
RIP: 0010:fbcon_get_font+0x229/0x800 drivers/video/fbdev/core/fbcon.c:2286
Call Trace:
<TASK>
con_font_get drivers/tty/vt/vt.c:4558 [inline]
con_font_op+0x1fc/0xf20 drivers/tty/vt/vt.c:4673
vt_k_ioctl drivers/tty/vt/vt_ioctl.c:474 [inline]
vt_ioctl+0x632/0x2ec0 drivers/tty/vt/vt_ioctl.c:752
tty_ioctl+0x6f8/0x1570 drivers/tty/tty_io.c:2803
vfs_ioctl fs/ioctl.c:51 [inline]
...
So restore the font data in any case, not only for user fonts. Note the
later 'if' is now protected by 'old_userfont' and not 'old_data' as the
latter is always set now. (And it is supposed to be non-NULL. Otherwise
we would see the bug above again.)
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Fixes: a5a923038d ("fbdev: fbcon: Properly revert changes when vc_resize() failed")
Reported-and-tested-by: Ubisectech Sirius <bugreport@ubisectech.com>
Cc: Ubisectech Sirius <bugreport@ubisectech.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Helge Deller <deller@gmx.de>
Cc: linux-fbdev@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20240208114411.14604-1-jirislaby@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d82f32202e ]
Before attempting to support the pre-ratification version of vector
found on older T-Head CPUs, disallow "v" in riscv,isa on these
platforms. The deprecated property has no clear way to communicate
the specific version of vector that is supported and much of the vendor
provided software puts "v" in the isa string. riscv,isa-extensions
should be used instead. This should not be too much of a burden for
these systems, as the vendor shipped devicetrees and firmware do not
work with a mainline kernel and will require updating.
We can limit this restriction to only ignore v in riscv,isa on CPUs
that report T-Head's vendor ID and a zero marchid. Newer T-Head CPUs
that support the ratified version of vector should report non-zero
marchid, according to Guo Ren [1].
Link: https://lore.kernel.org/linux-riscv/CAJF2gTRy5eK73=d6s7CVy9m9pB8p4rAoMHM3cZFwzg=AuF7TDA@mail.gmail.com/ [1]
Fixes: dc6667a4e7 ("riscv: Extending cpufeature.c to detect V-extension")
Co-developed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Guo Ren <guoren@kernel.org>
Link: https://lore.kernel.org/r/20240223-tidings-shabby-607f086cb4d7@spud
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eba2eb2495 ]
snd_soc_card_get_kcontrol() must be holding a read lock on
card->controls_rwsem while walking the controls list.
Compare with snd_ctl_find_numid().
The existing function is renamed snd_soc_card_get_kcontrol_locked()
so that it can be called from contexts that are already holding
card->controls_rwsem (for example, control get/put functions).
There are few direct or indirect callers of
snd_soc_card_get_kcontrol(), and most are safe. Three require
changes, which have been included in this patch:
codecs/cs35l45.c:
cs35l45_activate_ctl() is called from a control put() function so
is changed to call snd_soc_card_get_kcontrol_locked().
codecs/cs35l56.c:
cs35l56_sync_asp1_mixer_widgets_with_firmware() is called from
control get()/put() functions so is changed to call
snd_soc_card_get_kcontrol_locked().
fsl/fsl_xcvr.c:
fsl_xcvr_activate_ctl() is called from three places, one of which
already holds card->controls_rwsem:
1. fsl_xcvr_mode_put(), a control put function, which will
already be holding card->controls_rwsem.
2. fsl_xcvr_startup(), a DAI startup function.
3. fsl_xcvr_shutdown(), a DAI shutdown function.
To fix this, fsl_xcvr_activate_ctl() has been changed to call
snd_soc_card_get_kcontrol_locked() so that it is safe to call
directly from fsl_xcvr_mode_put().
The fsl_xcvr_startup() and fsl_xcvr_shutdown() functions have been
changed to take a read lock on card->controls_rsem() around calls
to fsl_xcvr_activate_ctl(). While this is not very elegant, it
keeps the change small, to avoid this patch creating a large
collateral churn in fsl/fsl_xcvr.c.
Analysis of other callers of snd_soc_card_get_kcontrol() is that
they do not need any changes, they are not holding card->controls_rwsem
when they call snd_soc_card_get_kcontrol().
Direct callers of snd_soc_card_get_kcontrol():
fsl/fsl_spdif.c: fsl_spdif_dai_probe() - DAI probe function
fsl/fsl_micfil.c: voice_detected_fn() - IRQ handler
Indirect callers via soc_component_notify_control():
codecs/cs42l43: cs42l43_mic_shutter() - IRQ handler
codecs/cs42l43: cs42l43_spk_shutter() - IRQ handler
codecs/ak4118.c: ak4118_irq_handler() - IRQ handler
codecs/wm_adsp.c: wm_adsp_write_ctl() - not currently used
Indirect callers via snd_soc_limit_volume():
qcom/sc8280xp.c: sc8280xp_snd_init() - DAIlink init function
ti/rx51.c: rx51_aic34_init() - DAI init function
I don't have hardware to test the fsl/*, qcom/sc828xp.c, ti/rx51.c
and ak4118.c changes.
Backport note:
The fsl/, qcom/, cs35l45, cs35l56 and cs42l43 callers were added
since the Fixes commit so won't all be present on older kernels.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 209c6cdfd2 ("ASoC: soc-card: move snd_soc_card_get_kcontrol() to soc-card")
Link: https://lore.kernel.org/r/20240221123710.690224-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c14f09f010 ]
Rewrite the handling of ASP1 TX mixer mux initialization to prevent a
deadlock during component_remove().
The firmware can overwrite the ASP1 TX mixer registers with
system-specific settings. This is mainly for hardware that uses the
ASP as a chip-to-chip link controlled by the firmware. Because of this
the driver cannot know the starting state of the ASP1 mixer muxes until
the firmware has been downloaded and rebooted.
The original workaround for this was to queue a work function from the
dsp_work() job. This work then read the register values (populating the
regmap cache the first time around) and then called
snd_soc_dapm_mux_update_power(). The problem with this is that it was
ultimately triggered by cs35l56_component_probe() queueing dsp_work,
which meant that it would be running in parallel with the rest of the
ASoC component and card initialization. To prevent accessing DAPM before
it was fully initialized the work function took the card mutex. But this
would deadlock if cs35l56_component_remove() was called before the work job
had completed, because ASoC calls component_remove() with the card mutex
held.
This new version removes the work function. Instead the regmap cache and
DAPM mux widgets are initialized the first time any of the associated ALSA
controls is read or written.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 07f7d6e7a1 ("ASoC: cs35l56: Fix for initializing ASP1 mixer registers")
Link: https://lore.kernel.org/r/20240208123742.1278104-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f6c967941c ]
Put the silicon revision and secured flag in the wm_adsp fwf_name
string instead of including them in the part string.
This changes the format of the firmware name string from
cs35l56[s]-rev-misc[-system_name]
to
cs35l56-rev[-s]-misc[-system_name]
No firmware files have been published, so this doesn't cause a
compatibility break.
Silicon revision and secured flag are included in the firmware
filename to pick a firmware compatible with the part. These strings
were being added to the part string, but that is a misuse of the
string. The correct place for these is the fwf_name string, which
is specifically intended to select between multiple firmware files
for the same part.
Backport note:
This won't apply to kernels older than v6.6.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 608f1b0dbd ("ASoC: cs35l56: Move DSP part string generation so that it is done only once")
Link: https://msgid.link/r/20240129162737.497-12-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 07f7d6e7a1 ]
Defer initializing the state of the ASP1 mixer registers until
the firmware has been downloaded and rebooted.
On a SoundWire system the ASP is free for use as a chip-to-chip
interconnect. This can be either for the firmware on multiple
CS35L56 to share reference audio; or as a bridge to another
device. If it is a firmware interconnect it is owned by the
firmware and the Linux driver should avoid writing the registers.
However, if it is a bridge then Linux may take over and handle
it as a normal codec-to-codec link. Even if the ASP is used
as a firmware-firmware interconnect it is useful to have
ALSA controls for the ASP mixer. They are at least useful for
debugging.
CS35L56 is designed for SDCA and a generic SDCA driver would
know nothing about these chip-specific registers. So if the
ASP is being used on a SoundWire system the firmware sets up the
ASP mixer registers. This means that we can't assume the default
state of these registers. But we don't know the initial state
that the firmware set them to until after the firmware has been
downloaded and booted, which can take several seconds when
downloading multiple amps.
DAPM normally reads the initial state of mux registers during
probe() but this would mean blocking probe() for several seconds
until the firmware has initialized them. To avoid this, the
mixer muxes are set SND_SOC_NOPM to prevent DAPM trying to read
the register state. Custom get/set callbacks are implemented for
ALSA control access, and these can safely block waiting for the
firmware download.
After the firmware download has completed, the state of the
mux registers is known so a work job is queued to call
snd_soc_dapm_mux_update_power() on each of the mux widgets.
Backport note:
This won't apply cleanly to kernels older than v6.6.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: e496112529 ("ASoC: cs35l56: Add driver for Cirrus Logic CS35L56")
Link: https://msgid.link/r/20240129162737.497-11-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 07687cd053 ]
Move the call to cs35l56_set_patch() earlier in cs35l56_init() so
that it only adds the register patch on first-time initialization.
The call was after the post_soft_reset label, so every time this
function was run to re-initialize the hardware after a reset it would
call regmap_register_patch() and add the same reg_sequence again.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 898673b905 ("ASoC: cs35l56: Move shared data into a common data structure")
Link: https://msgid.link/r/20240129162737.497-6-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ae861c466e ]
The cs35l56->component pointer is used by the suspend-resume handling to
know whether the driver is fully instantiated. This is to prevent it
queuing dsp_work which would result in calling wm_adsp when the driver
is not an instantiated ASoC component. So this pointer must be cleared
by cs35l56_component_remove().
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: e496112529 ("ASoC: cs35l56: Add driver for Cirrus Logic CS35L56")
Link: https://msgid.link/r/20240129162737.497-4-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1382d8b551 ]
In the case where __lpass_get_dmactl_handle is called and the driver
id dai_id is invalid the pointer dmactl is not being assigned a value,
and dmactl contains a garbage value since it has not been initialized
and so the null check may not work. Fix this to initialize dmactl to
NULL. One could argue that modern compilers will set this to zero, but
it is useful to keep this initialized as per the same way in functions
__lpass_platform_codec_intf_init and lpass_cdc_dma_daiops_hw_params.
Cleans up clang scan build warning:
sound/soc/qcom/lpass-cdc-dma.c:275:7: warning: Branch condition
evaluates to a garbage value [core.uninitialized.Branch]
Fixes: b81af585ea ("ASoC: qcom: Add lpass CPU driver for codec dma control")
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://msgid.link/r/20240221134804.3475989-1-colin.i.king@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e33625c84b ]
The driver must write 0 to HALO_STATE before sending the SYSTEM_RESET
command to the firmware.
HALO_STATE is in DSP memory, which is preserved across a soft reset.
The SYSTEM_RESET command does not change the value of HALO_STATE.
There is period of time while the CS35L56 is resetting, before the
firmware has started to boot, where a read of HALO_STATE will return
the value it had before the SYSTEM_RESET. If the driver does not
clear HALO_STATE, this would return BOOT_DONE status even though the
firmware has not booted.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 8a731fd37f ("ASoC: cs35l56: Move utility functions to shared file")
Link: https://msgid.link/r/20240216140535.1434933-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2df70149e7 ]
The bq27xxx i2c-client may not have an IRQ, in which case
client->irq will be 0. bq27xxx_battery_i2c_probe() already has
an if (client->irq) check wrapping the request_threaded_irq().
But bq27xxx_battery_i2c_remove() unconditionally calls
free_irq(client->irq) leading to:
[ 190.310742] ------------[ cut here ]------------
[ 190.310843] Trying to free already-free IRQ 0
[ 190.310861] WARNING: CPU: 2 PID: 1304 at kernel/irq/manage.c:1893 free_irq+0x1b8/0x310
Followed by a backtrace when unbinding the driver. Add
an if (client->irq) to bq27xxx_battery_i2c_remove() mirroring
probe() to fix this.
Fixes: 444ff00734 ("power: supply: bq27xxx: Fix I2C IRQ race on remove")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240215155133.70537-1-hdegoede@redhat.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fccfa646ef ]
gcc-14 notices that the allocation with sizeof(void) on 32-bit architectures
is not enough for a 64-bit phys_addr_t:
drivers/firmware/efi/capsule-loader.c: In function 'efi_capsule_open':
drivers/firmware/efi/capsule-loader.c:295:24: error: allocation of insufficient size '4' for type 'phys_addr_t' {aka 'long long unsigned int'} with size '8' [-Werror=alloc-size]
295 | cap_info->phys = kzalloc(sizeof(void *), GFP_KERNEL);
| ^
Use the correct type instead here.
Fixes: f24c4d4780 ("efi/capsule-loader: Reinstate virtual capsule mapping")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 13114dc554 ]
When the decrypt request goes to the backlog and crypto_aead_decrypt
returns -EBUSY, tls_do_decryption will wait until all async
decryptions have completed. If one of them fails, tls_do_decryption
will return -EBADMSG and tls_decrypt_sg jumps to the error path,
releasing all the pages. But the pages have been passed to the async
callback, and have already been released by tls_decrypt_done.
The only true async case is when crypto_aead_decrypt returns
-EINPROGRESS. With -EBUSY, we already waited so we can tell
tls_sw_recvmsg that the data is available for immediate copy, but we
need to notify tls_decrypt_sg (via the new ->async_done flag) that the
memory has already been released.
Fixes: 8590541473 ("net: tls: handle backlogging of crypto requests")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://lore.kernel.org/r/4755dd8d9bebdefaa19ce1439b833d6199d4364c.1709132643.git.sd@queasysnail.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 41532b785e ]
If we're not doing async, the handling is much simpler. There's no
reference counting, we just need to wait for the completion to wake us
up and return its result.
We should preferably also use a separate crypto_wait. I'm not seeing a
UAF as I did in the past, I think aec7961916 ("tls: fix race between
async notify and socket close") took care of it.
This will make the next fix easier.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://lore.kernel.org/r/47bde5f649707610eaef9f0d679519966fc31061.1709132643.git.sd@queasysnail.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 13114dc554 ("tls: fix use-after-free on failed backlog decryption")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6caaf10442 ]
If we peek from 2 records with a currently empty rx_list, and the
first record is decrypted synchronously but the second record is
decrypted async, the following happens:
1. decrypt record 1 (sync)
2. copy from record 1 to the userspace's msg
3. queue the decrypted record to rx_list for future read(!PEEK)
4. decrypt record 2 (async)
5. queue record 2 to rx_list
6. call process_rx_list to copy data from the 2nd record
We currently pass copied=0 as skip offset to process_rx_list, so we
end up copying once again from the first record. We should skip over
the data we've already copied.
Seen with selftest tls.12_aes_gcm.recv_peek_large_buf_mult_recs
Fixes: 692d7b5d1f ("tls: Fix recvmsg() to be able to peek across multiple records")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://lore.kernel.org/r/1b132d2b2b99296bfde54e8a67672d90d6d16e71.1709132643.git.sd@queasysnail.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f7fa16d498 ]
With mixed sync/async decryption, or failures of crypto_aead_decrypt,
we increment decrypt_pending but we never do the corresponding
decrement since tls_decrypt_done will not be called. In this case, we
should decrement decrypt_pending immediately to avoid getting stuck.
For example, the prequeue prequeue test gets stuck with mixed
modes (one async decrypt + one sync decrypt).
Fixes: 94524d8fc9 ("net/tls: Add support for async decryption of tls records")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://lore.kernel.org/r/c56d5fc35543891d5319f834f25622360e1bfbec.1709132643.git.sd@queasysnail.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51dd4ee037 ]
Current HSR implementation uses following supervisory frame (even for
HSRv1 the HSR tag is not is not present):
00000000: 01 15 4e 00 01 2d XX YY ZZ 94 77 10 88 fb 00 01
00000010: 7e 1c 17 06 XX YY ZZ 94 77 10 1e 06 XX YY ZZ 94
00000020: 77 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00000030: 00 00 00 00 00 00 00 00 00 00 00 00
The current code adds extra two bytes (i.e. sizeof(struct hsr_sup_tlv))
when offset for skb_pull() is calculated.
This is wrong, as both 'struct hsrv1_ethhdr_sp' and 'hsrv0_ethhdr_sp'
already have 'struct hsr_sup_tag' defined in them, so there is no need
for adding extra two bytes.
This code was working correctly as with no RedBox support, the check for
HSR_TLV_EOT (0x00) was off by two bytes, which were corresponding to
zeroed padded bytes for minimal packet size.
Fixes: eafaa88b3e ("net: hsr: Add support for redbox supervision frames")
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20240228085644.3618044-1-lukma@denx.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 743ad091fb ]
In the commit d73ef2d69c ("rtnetlink: let rtnl_bridge_setlink checks
IFLA_BRIDGE_MODE length"), an adjustment was made to the old loop logic
in the function `rtnl_bridge_setlink` to enable the loop to also check
the length of the IFLA_BRIDGE_MODE attribute. However, this adjustment
removed the `break` statement and led to an error logic of the flags
writing back at the end of this function.
if (have_flags)
memcpy(nla_data(attr), &flags, sizeof(flags));
// attr should point to IFLA_BRIDGE_FLAGS NLA !!!
Before the mentioned commit, the `attr` is granted to be IFLA_BRIDGE_FLAGS.
However, this is not necessarily true fow now as the updated loop will let
the attr point to the last NLA, even an invalid NLA which could cause
overflow writes.
This patch introduces a new variable `br_flag` to save the NLA pointer
that points to IFLA_BRIDGE_FLAGS and uses it to resolve the mentioned
error logic.
Fixes: d73ef2d69c ("rtnetlink: let rtnl_bridge_setlink checks IFLA_BRIDGE_MODE length")
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20240227121128.608110-1-linma@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6c65eb20f ]
We never increment the group number iterator, so all groups
get recorded into index 0 of the mcast_groups[] array.
As a result YNL can only handle using the last group.
For example using the "netdev" sample on kernel with
page pool commands results in:
$ ./samples/netdev
YNL: Multicast group 'mgmt' not found
Most families have only one multicast group, so this hasn't
been noticed. Plus perhaps developers usually test the last
group which would have worked.
Fixes: 86878f14d7 ("tools: ynl: user space helpers")
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Link: https://lore.kernel.org/r/20240226214019.1255242-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62e7151ae3 ]
conntrack nf_confirm logic cannot handle cloned skbs referencing
the same nf_conn entry, which will happen for multicast (broadcast)
frames on bridges.
Example:
macvlan0
|
br0
/ \
ethX ethY
ethX (or Y) receives a L2 multicast or broadcast packet containing
an IP packet, flow is not yet in conntrack table.
1. skb passes through bridge and fake-ip (br_netfilter)Prerouting.
-> skb->_nfct now references a unconfirmed entry
2. skb is broad/mcast packet. bridge now passes clones out on each bridge
interface.
3. skb gets passed up the stack.
4. In macvlan case, macvlan driver retains clone(s) of the mcast skb
and schedules a work queue to send them out on the lower devices.
The clone skb->_nfct is not a copy, it is the same entry as the
original skb. The macvlan rx handler then returns RX_HANDLER_PASS.
5. Normal conntrack hooks (in NF_INET_LOCAL_IN) confirm the orig skb.
The Macvlan broadcast worker and normal confirm path will race.
This race will not happen if step 2 already confirmed a clone. In that
case later steps perform skb_clone() with skb->_nfct already confirmed (in
hash table). This works fine.
But such confirmation won't happen when eb/ip/nftables rules dropped the
packets before they reached the nf_confirm step in postrouting.
Pablo points out that nf_conntrack_bridge doesn't allow use of stateful
nat, so we can safely discard the nf_conn entry and let inet call
conntrack again.
This doesn't work for bridge netfilter: skb could have a nat
transformation. Also bridge nf prevents re-invocation of inet prerouting
via 'sabotage_in' hook.
Work around this problem by explicit confirmation of the entry at LOCAL_IN
time, before upper layer has a chance to clone the unconfirmed entry.
The downside is that this disables NAT and conntrack helpers.
Alternative fix would be to add locking to all code parts that deal with
unconfirmed packets, but even if that could be done in a sane way this
opens up other problems, for example:
-m physdev --physdev-out eth0 -j SNAT --snat-to 1.2.3.4
-m physdev --physdev-out eth1 -j SNAT --snat-to 1.2.3.5
For multicast case, only one of such conflicting mappings will be
created, conntrack only handles 1:1 NAT mappings.
Users should set create a setup that explicitly marks such traffic
NOTRACK (conntrack bypass) to avoid this, but we cannot auto-bypass
them, ruleset might have accept rules for untracked traffic already,
so user-visible behaviour would change.
Suggested-by: Pablo Neira Ayuso <pablo@netfilter.org>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217777
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e0f122c65 ]
Commit d0009effa8 ("netfilter: nf_tables: validate NFPROTO_* family") added
some validation of NFPROTO_* families in the nft_compat module, but it broke
the ability to use legacy iptables modules in dual-stack nftables.
While with legacy iptables one had to independently manage IPv4 and IPv6
tables, with nftables it is possible to have dual-stack tables sharing the
rules. Moreover, it was possible to use rules based on legacy iptables
match/target modules in dual-stack nftables.
As an example, the program from [2] creates an INET dual-stack family table
using an xt_bpf based rule, which looks like the following (the actual output
was generated with a patched nft tool as the current nft tool does not parse
dual stack tables with legacy match rules, so consider it for illustrative
purposes only):
table inet testfw {
chain input {
type filter hook prerouting priority filter; policy accept;
bytecode counter packets 0 bytes 0 accept
}
}
After d0009effa8 ("netfilter: nf_tables: validate NFPROTO_* family") we get
EOPNOTSUPP for the above program.
Fix this by allowing NFPROTO_INET for nft_(match/target)_validate(), but also
restrict the functions to classic iptables hooks.
Changes in v3:
* clarify that upstream nft will not display such configuration properly and
that the output was generated with a patched nft tool
* remove example program from commit description and link to it instead
* no code changes otherwise
Changes in v2:
* restrict nft_(match/target)_validate() to classic iptables hooks
* rewrite example program to use unmodified libnftnl
Fixes: d0009effa8 ("netfilter: nf_tables: validate NFPROTO_* family")
Link: https://lore.kernel.org/all/Zc1PfoWN38UuFJRI@calendula/T/#mc947262582c90fec044c7a3398cc92fac7afea72 [1]
Link: https://lore.kernel.org/all/20240220145509.53357-1-ignat@cloudflare.com/ [2]
Reported-by: Jordan Griege <jgriege@cloudflare.com>
Signed-off-by: Ignat Korchagin <ignat@cloudflare.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6abf9dd26b ]
hci_coredump_qca() uses __hci_cmd_sync() to send a vendor-specific command
to trigger firmware coredump, but the command does not have any event as
its sync response, so it is not suitable to use __hci_cmd_sync(), fixed by
using __hci_cmd_send().
Fixes: 06d3fdfcdf ("Bluetooth: hci_qca: Add qcom devcoredump support")
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7dcd3e014a ]
BT adapter going into UNCONFIGURED state during BT turn ON when
devicetree has no local-bd-address node.
Bluetooth will not work out of the box on such devices, to avoid this
problem, added check to set HCI_QUIRK_USE_BDADDR_PROPERTY based on
local-bd-address node entry.
When this quirk is not set, the public Bluetooth address read by host
from controller though HCI Read BD Address command is
considered as valid.
Fixes: e668eb1e15 ("Bluetooth: hci_core: Don't stop BT if the BD address missing in dts")
Signed-off-by: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e4b019515f ]
Right now Linux BT stack cannot pass test case "GAP/CONN/CPUP/BV-05-C
'Connection Parameter Update Procedure Invalid Parameters Central
Responder'" in Bluetooth Test Suite revision GAP.TS.p44. [0]
That was revoled by commit c49a8682fc ("Bluetooth: validate BLE
connection interval updates"), but later got reverted due to devices
like keyboards and mice may require low connection interval.
So only validate the max value connection interval to pass the Test
Suite, and let devices to request low connection interval if needed.
[0] https://www.bluetooth.org/docman/handlers/DownloadDoc.ashx?doc_id=229869
Fixes: 68d19d7d99 ("Revert "Bluetooth: validate BLE connection interval updates"")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61a5ab72ed ]
hci_store_wake_reason() wrongly parses event HCI_Connection_Request
as HCI_Connection_Complete and HCI_Connection_Complete as
HCI_Connection_Request, so causes recording wakeup BD_ADDR error and
potential stability issue, fix it by using the correct field.
Fixes: 2f20216c1d ("Bluetooth: Emit controller suspend and resume events")
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5469adb2a ]
During suspend, only wakeable devices can be in acceptlist, so if the
device was previously added it needs to be removed otherwise the device
can end up waking up the system prematurely.
Fixes: 3b42055388 ("Bluetooth: hci_sync: Fix attempting to suspend with unfiltered passive scan")
Signed-off-by: Clancy Shang <clancy.shang@quectel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2449007d3f ]
While handling the HCI_EV_HARDWARE_ERROR event, if the underlying
BT controller is not responding, the GPIO reset mechanism would
free the hci_dev and lead to a use-after-free in hci_error_reset.
Here's the call trace observed on a ChromeOS device with Intel AX201:
queue_work_on+0x3e/0x6c
__hci_cmd_sync_sk+0x2ee/0x4c0 [bluetooth <HASH:3b4a6>]
? init_wait_entry+0x31/0x31
__hci_cmd_sync+0x16/0x20 [bluetooth <HASH:3b4a 6>]
hci_error_reset+0x4f/0xa4 [bluetooth <HASH:3b4a 6>]
process_one_work+0x1d8/0x33f
worker_thread+0x21b/0x373
kthread+0x13a/0x152
? pr_cont_work+0x54/0x54
? kthread_blkcg+0x31/0x31
ret_from_fork+0x1f/0x30
This patch holds the reference count on the hci_dev while processing
a HCI_EV_HARDWARE_ERROR event to avoid potential crash.
Fixes: c7741d16a5 ("Bluetooth: Perform a power cycle when receiving hardware error event")
Signed-off-by: Ying Hsu <yinghsu@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b3899be24 ]
There's a very confusing mistake in the code starting a HCI inquiry: We're
calling hci_dev_test_flag() to test for HCI_INQUIRY, but hci_dev_test_flag()
checks hdev->dev_flags instead of hdev->flags. HCI_INQUIRY is a bit that's
set on hdev->flags, not on hdev->dev_flags though.
HCI_INQUIRY equals the integer 7, and in hdev->dev_flags, 7 means
HCI_BONDABLE, so we were actually checking for HCI_BONDABLE here.
The mistake is only present in the synchronous code for starting an inquiry,
not in the async one. Also devices are typically bondable while doing an
inquiry, so that might be the reason why nobody noticed it so far.
Fixes: abfeea476c ("Bluetooth: hci_sync: Convert MGMT_OP_START_DISCOVERY")
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8af411bbba ]
Currently when suspending driver and stopping workqueue it is checked whether
workqueue is not NULL and if so, it is destroyed.
Function destroy_workqueue() does drain queue and does clear variable, but
it does not set workqueue variable to NULL. This can cause kernel/module
panic if code attempts to clear workqueue that was not initialized.
This scenario is possible when resuming suspended driver in stmmac_resume(),
because there is no handling for failed stmmac_hw_setup(),
which can fail and return if DMA engine has failed to initialize,
and workqueue is initialized after DMA engine.
Should DMA engine fail to initialize, resume will proceed normally,
but interface won't work and TX queue will eventually timeout,
causing 'Reset adapter' error.
This then does destroy workqueue during reset process.
And since workqueue is initialized after DMA engine and can be skipped,
it will cause kernel/module panic.
To secure against this possible crash, set workqueue variable to NULL when
destroying workqueue.
Log/backtrace from crash goes as follows:
[88.031977]------------[ cut here ]------------
[88.031985]NETDEV WATCHDOG: eth0 (sxgmac): transmit queue 1 timed out
[88.032017]WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:477 dev_watchdog+0x390/0x398
<Skipping backtrace for watchdog timeout>
[88.032251]---[ end trace e70de432e4d5c2c0 ]---
[88.032282]sxgmac 16d88000.ethernet eth0: Reset adapter.
[88.036359]------------[ cut here ]------------
[88.036519]Call trace:
[88.036523] flush_workqueue+0x3e4/0x430
[88.036528] drain_workqueue+0xc4/0x160
[88.036533] destroy_workqueue+0x40/0x270
[88.036537] stmmac_fpe_stop_wq+0x4c/0x70
[88.036541] stmmac_release+0x278/0x280
[88.036546] __dev_close_many+0xcc/0x158
[88.036551] dev_close_many+0xbc/0x190
[88.036555] dev_close.part.0+0x70/0xc0
[88.036560] dev_close+0x24/0x30
[88.036564] stmmac_service_task+0x110/0x140
[88.036569] process_one_work+0x1d8/0x4a0
[88.036573] worker_thread+0x54/0x408
[88.036578] kthread+0x164/0x170
[88.036583] ret_from_fork+0x10/0x20
[88.036588]---[ end trace e70de432e4d5c2c1 ]---
[88.036597]Unable to handle kernel NULL pointer dereference at virtual address 0000000000000004
Fixes: 5a5586112b ("net: stmmac: support FPE link partner hand-shaking procedure")
Signed-off-by: Jakub Raczynski <j.raczynski@samsung.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c68b2c9eba ]
The MII code does not check the return value of mdio_read (among
others), and therefore no error code should be sent. A previous fix to
the use of an uninitialized variable propagates negative error codes,
that might lead to wrong operations by the MII library.
An example of such issues is the use of mii_nway_restart by the dm9601
driver. The mii_nway_restart function does not check the value returned
by mdio_read, which in this case might be a negative number which could
contain the exact bit the function checks (BMCR_ANENABLE = 0x1000).
Return zero in case of error, as it is common practice in users of
mdio_read to avoid wrong uses of the return value.
Fixes: 8f8abb863f ("net: usb: dm9601: fix uninitialized variable use in dm9601_mdio_read")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Peter Korsgaard <peter@korsgaard.com>
Link: https://lore.kernel.org/r/20240225-dm9601_ret_err-v1-1-02c1d959ea59@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e67899abf ]
Same as LAN7800, LAN7850 can be used without EEPROM. If EEPROM is not
present or not flashed, LAN7850 will fail to sync the speed detected by the PHY
with the MAC. In case link speed is 100Mbit, it will accidentally work,
otherwise no data can be transferred.
Better way would be to implement link_up callback, or set auto speed
configuration unconditionally. But this changes would be more intrusive.
So, for now, set it only if no EEPROM is found.
Fixes: e69647a19c ("lan78xx: Set ASD in MAC_CR when EEE is enabled.")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20240222123839.2816561-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 10bfd453da ]
It seems that if userspace provides a correct IFA_TARGET_NETNSID value
but no IFA_ADDRESS and IFA_LOCAL attributes, inet6_rtm_getaddr()
returns -EINVAL with an elevated "struct net" refcount.
Fixes: 6ecf4c37eb ("ipv6: enable IFA_TARGET_NETNSID for RTM_GETADDR")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Christian Brauner <brauner@kernel.org>
Cc: David Ahern <dsahern@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe9f801355 ]
veth sets NETIF_F_GRO automatically when XDP is enabled,
because both features use the same NAPI machinery.
The logic to clear NETIF_F_GRO sits in veth_disable_xdp() which
is called both on ndo_stop and when XDP is turned off.
To avoid the flag from being cleared when the device is brought
down, the clearing is skipped when IFF_UP is not set.
Bringing the device down should indeed not modify its features.
Unfortunately, this means that clearing is also skipped when
XDP is disabled _while_ the device is down. And there's nothing
on the open path to bring the device features back into sync.
IOW if user enables XDP, disables it and then brings the device
up we'll end up with a stray GRO flag set but no NAPI instances.
We don't depend on the GRO flag on the datapath, so the datapath
won't crash. We will crash (or hang), however, next time features
are sync'ed (either by user via ethtool or peer changing its config).
The GRO flag will go away, and veth will try to disable the NAPIs.
But the open path never created them since XDP was off, the GRO flag
was a stray. If NAPI was initialized before we'll hang in napi_disable().
If it never was we'll crash trying to stop uninitialized hrtimer.
Move the GRO flag updates to the XDP enable / disable paths,
instead of mixing them with the ndo_open / ndo_close paths.
Fixes: d3256efd8e ("veth: allow enabling NAPI even without XDP")
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Reported-by: syzbot+039399a9b96297ddedca@syzkaller.appspotmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f0a0fc10ab ]
There is a loophole in pstate limit clamping for the intel_cpufreq CPU
frequency scaling driver (intel_pstate in passive mode), schedutil CPU
frequency scaling governor, HWP (HardWare Pstate) control enabled, when
the adjust_perf call back path is used.
Fix it.
Fixes: a365ab6b9d cpufreq: intel_pstate: Implement the ->adjust_perf() callback
Signed-off-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 734f06db59 ]
Since commit 5d93cfcf73 ("net: dpaa: Convert to phylink"), we support
the "10gbase-r" phy-mode through a driver-based conversion of "xgmii",
but we still don't actually support it when the device tree specifies
"10gbase-r" proper.
This is because boards such as LS1046A-RDB do not define pcs-handle-names
(for whatever reason) in the ethernet@f0000 device tree node, and the
code enters through this code path:
err = of_property_match_string(mac_node, "pcs-handle-names", "xfi");
// code takes neither branch and falls through
if (err >= 0) {
(...)
} else if (err != -EINVAL && err != -ENODATA) {
goto _return_fm_mac_free;
}
(...)
/* For compatibility, if pcs-handle-names is missing, we assume this
* phy is the first one in pcsphy-handle
*/
err = of_property_match_string(mac_node, "pcs-handle-names", "sgmii");
if (err == -EINVAL || err == -ENODATA)
pcs = memac_pcs_create(mac_node, 0); // code takes this branch
else if (err < 0)
goto _return_fm_mac_free;
else
pcs = memac_pcs_create(mac_node, err);
// A default PCS is created and saved in "pcs"
// This determination fails and mistakenly saves the default PCS
// memac->sgmii_pcs instead of memac->xfi_pcs, because at this
// stage, mac_dev->phy_if == PHY_INTERFACE_MODE_10GBASER.
if (err && mac_dev->phy_if == PHY_INTERFACE_MODE_XGMII)
memac->xfi_pcs = pcs;
else
memac->sgmii_pcs = pcs;
In other words, in the absence of pcs-handle-names, the default
xfi_pcs assignment logic only works when in the device tree we have
PHY_INTERFACE_MODE_XGMII.
By reversing the order between the fallback xfi_pcs assignment and the
"xgmii" overwrite with "10gbase-r", we are able to support both values
in the device tree, with identical behavior.
Currently, it is impossible to make the s/xgmii/10gbase-r/ device tree
conversion, because it would break forward compatibility (new device
tree with old kernel). The only way to modify existing device trees to
phy-interface-mode = "10gbase-r" is to fix stable kernels to accept this
value and handle it properly.
One reason why the conversion is desirable is because with pre-phylink
kernels, the Aquantia PHY driver used to warn about the improper use
of PHY_INTERFACE_MODE_XGMII [1]. It is best to have a single (latest)
device tree that works with all supported stable kernel versions.
Note that the blamed commit does not constitute a regression per se.
Older stable kernels like 6.1 still do not work with "10gbase-r", but
for a different reason. That is a battle for another time.
[1] https://lore.kernel.org/netdev/20240214-ls1046-dts-use-10gbase-r-v1-1-8c2d68547393@concurrent-rt.com/
Fixes: 5d93cfcf73 ("net: dpaa: Convert to phylink")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3773d65ae5 ]
Currently, mctp_local_output only takes ownership of skb on success, and
we may leak an skb if mctp_local_output fails in specific states; the
skb ownership isn't transferred until the actual output routing occurs.
Instead, make mctp_local_output free the skb on all error paths up to
the route action, so it always consumes the passed skb.
Fixes: 833ef3b91d ("mctp: Populate socket implementation")
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240220081053.1439104-1-jk@codeconstruct.com.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ae1e9922b ]
syzkaller triggered following kasan splat:
BUG: KASAN: use-after-free in __skb_flow_dissect+0x19d1/0x7a50 net/core/flow_dissector.c:1170
Read of size 1 at addr ffff88812fb4000e by task syz-executor183/5191
[..]
kasan_report+0xda/0x110 mm/kasan/report.c:588
__skb_flow_dissect+0x19d1/0x7a50 net/core/flow_dissector.c:1170
skb_flow_dissect_flow_keys include/linux/skbuff.h:1514 [inline]
___skb_get_hash net/core/flow_dissector.c:1791 [inline]
__skb_get_hash+0xc7/0x540 net/core/flow_dissector.c:1856
skb_get_hash include/linux/skbuff.h:1556 [inline]
ip_tunnel_xmit+0x1855/0x33c0 net/ipv4/ip_tunnel.c:748
ipip_tunnel_xmit+0x3cc/0x4e0 net/ipv4/ipip.c:308
__netdev_start_xmit include/linux/netdevice.h:4940 [inline]
netdev_start_xmit include/linux/netdevice.h:4954 [inline]
xmit_one net/core/dev.c:3548 [inline]
dev_hard_start_xmit+0x13d/0x6d0 net/core/dev.c:3564
__dev_queue_xmit+0x7c1/0x3d60 net/core/dev.c:4349
dev_queue_xmit include/linux/netdevice.h:3134 [inline]
neigh_connected_output+0x42c/0x5d0 net/core/neighbour.c:1592
...
ip_finish_output2+0x833/0x2550 net/ipv4/ip_output.c:235
ip_finish_output+0x31/0x310 net/ipv4/ip_output.c:323
..
iptunnel_xmit+0x5b4/0x9b0 net/ipv4/ip_tunnel_core.c:82
ip_tunnel_xmit+0x1dbc/0x33c0 net/ipv4/ip_tunnel.c:831
ipgre_xmit+0x4a1/0x980 net/ipv4/ip_gre.c:665
__netdev_start_xmit include/linux/netdevice.h:4940 [inline]
netdev_start_xmit include/linux/netdevice.h:4954 [inline]
xmit_one net/core/dev.c:3548 [inline]
dev_hard_start_xmit+0x13d/0x6d0 net/core/dev.c:3564
...
The splat occurs because skb->data points past skb->head allocated area.
This is because neigh layer does:
__skb_pull(skb, skb_network_offset(skb));
... but skb_network_offset() returns a negative offset and __skb_pull()
arg is unsigned. IOW, we skb->data gets "adjusted" by a huge value.
The negative value is returned because skb->head and skb->data distance is
more than 64k and skb->network_header (u16) has wrapped around.
The bug is in the ip_tunnel infrastructure, which can cause
dev->needed_headroom to increment ad infinitum.
The syzkaller reproducer consists of packets getting routed via a gre
tunnel, and route of gre encapsulated packets pointing at another (ipip)
tunnel. The ipip encapsulation finds gre0 as next output device.
This results in the following pattern:
1). First packet is to be sent out via gre0.
Route lookup found an output device, ipip0.
2).
ip_tunnel_xmit for gre0 bumps gre0->needed_headroom based on the future
output device, rt.dev->needed_headroom (ipip0).
3).
ip output / start_xmit moves skb on to ipip0. which runs the same
code path again (xmit recursion).
4).
Routing step for the post-gre0-encap packet finds gre0 as output device
to use for ipip0 encapsulated packet.
tunl0->needed_headroom is then incremented based on the (already bumped)
gre0 device headroom.
This repeats for every future packet:
gre0->needed_headroom gets inflated because previous packets' ipip0 step
incremented rt->dev (gre0) headroom, and ipip0 incremented because gre0
needed_headroom was increased.
For each subsequent packet, gre/ipip0->needed_headroom grows until
post-expand-head reallocations result in a skb->head/data distance of
more than 64k.
Once that happens, skb->network_header (u16) wraps around when
pskb_expand_head tries to make sure that skb_network_offset() is unchanged
after the headroom expansion/reallocation.
After this skb_network_offset(skb) returns a different (and negative)
result post headroom expansion.
The next trip to neigh layer (or anything else that would __skb_pull the
network header) makes skb->data point to a memory location outside
skb->head area.
v2: Cap the needed_headroom update to an arbitarily chosen upperlimit to
prevent perpetual increase instead of dropping the headroom increment
completely.
Reported-and-tested-by: syzbot+bfde3bef047a81b8fde6@syzkaller.appspotmail.com
Closes: https://groups.google.com/g/syzkaller-bugs/c/fL9G6GtWskY/m/VKk_PR5FBAAJ
Fixes: 243aad830e ("ip_gre: include route header_len in max_headroom calculation")
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240220135606.4939-1-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a0d18853c ]
BUG: KMSAN: uninit-value in nla_validate_range_unsigned lib/nlattr.c:222 [inline]
BUG: KMSAN: uninit-value in nla_validate_int_range lib/nlattr.c:336 [inline]
BUG: KMSAN: uninit-value in validate_nla lib/nlattr.c:575 [inline]
BUG: KMSAN: uninit-value in __nla_validate_parse+0x2e20/0x45c0 lib/nlattr.c:631
nla_validate_range_unsigned lib/nlattr.c:222 [inline]
nla_validate_int_range lib/nlattr.c:336 [inline]
validate_nla lib/nlattr.c:575 [inline]
...
The message in question matches this policy:
[NFTA_TARGET_REV] = NLA_POLICY_MAX(NLA_BE32, 255),
but because NLA_BE32 size in minlen array is 0, the validation
code will read past the malformed (too small) attribute.
Note: Other attributes, e.g. BITFIELD32, SINT, UINT.. are also missing:
those likely should be added too.
Reported-by: syzbot+3f497b07aa3baf2fb4d0@syzkaller.appspotmail.com
Reported-by: xingwei lee <xrivendell7@gmail.com>
Closes: https://lore.kernel.org/all/CABOYnLzFYHSnvTyS6zGa-udNX55+izqkOt2sB9WDqUcEGW6n8w@mail.gmail.com/raw
Fixes: ecaf75ffd5 ("netlink: introduce bigendian integer types")
Signed-off-by: Florian Westphal <fw@strlen.de>
Link: https://lore.kernel.org/r/20240221172740.5092-1-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 32ce3bb57b ]
dev_get_drvdata() gets used to acquire the pointer to cqspi and the SPI
controller. Neither embed the other; this lead to memory corruption.
On a given platform (Mobileye EyeQ5) the memory corruption is hidden
inside cqspi->f_pdata. Also, this uninitialised memory is used as a
mutex (ctlr->bus_lock_mutex) by spi_controller_suspend().
Fixes: 2087e85bb6 ("spi: cadence-quadspi: fix suspend-resume implementations")
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://msgid.link/r/20240222-cdns-qspi-pm-fix-v4-1-6b6af8bcbf59@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 85248d670b ]
ublk_cancel_dev() just calls ublk_cancel_queue() to cancel all pending
io commands after ublk request queue is idle. The only protection is just
the read & write of ubq->nr_io_ready and avoid duplicated command cancel,
so add one per-queue lock with cancel flag for providing this protection,
meantime move ublk_cancel_dev() out of ub->mutex.
Then we needn't to call io_uring_cmd_complete_in_task() to cancel
pending command. And the same cancel logic will be re-used for
cancelable uring command.
This patch basically reverts commit ac5902f84b ("ublk: fix AB-BA lockdep warning").
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20231009093324.957829-4-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9f106c765 ]
When client send SMB2_CREATE_ALLOCATION_SIZE create context, ksmbd update
old size to ->AllocationSize in smb2 create response. ksmbd_vfs_getattr()
should be called after it to get updated stat result.
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6122b0b42 ]
This driver includes the legacy GPIO APIs <linux/gpio.h> and
<linux/of_gpio.h> but does not use any symbols from any of
them.
Drop the includes.
Further the driver is requesting "reset-gpios" rather than
just "reset" from the GPIO framework. This is wrong because
the gpiolib core will add "-gpios" before processing the
request from e.g. device tree. Drop the suffix.
The last problem means that the optional RESET GPIO has
never been properly retrieved and used even if it existed,
but nobody noticed.
Fixes: c1124c09e1 ("ASoC: cs35l34: Initial commit of the cs35l34 CODEC driver.")
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20231201-descriptors-sound-cirrus-v2-3-ee9f9d4655eb@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
* Compatible with the Google Coral Edge TPU (Single and Dual Edge).
*/
/dts-v1/;
/plugin/;
/ {
compatible = "brcm,bcm2712";
fragment@0 {
target = <&pcie1>;
__overlay__ {
msi-parent = <&pcie1>;
};
};
};
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
