MT8173 is a 64-bit four core Soc.
And mt8173-evb is a evaluation board based on mt8173.
This commit add the devicetree binding document for
mediatek MT8173 SoC
MT8173 sysirq
MT8173 uart
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add r8a7779 specific support for IRLM bit configuration
in the INTC-IRQPIN driver. Without this code we need
special workaround code in arch/arm/mach-shmobile.
The IRLM bit for the INTC hardware exists on various
older SH-based SoCs and is used to select between two
modes for the external interrupt pins IRQ0 to IRQ3:
IRLM = 0: (default from reset on r8a7779)
In this mode the pins IRQ0 to IRQ3 are used together
to give a value between 0 and 15 to the SoC. External
logic is required for masking. This mode is not
supported by the INTC-IRQPIN driver.
IRLM = 1: (needs this patch or configuration elsewhere)
In this mode IRQ0 to IRQ3 operate as 4 individual
external interrupt pins. In this mode the SMSC ethernet
chip can be used via IRQ1 on r8a7779 Marzen. This mode
is the only supported mode by the INTC-IRQPIN driver.
For this patch to work the r8a7779 DTS needs to pass
the ICR0 register as the last register bank.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: horms@verge.net.au
Cc: jason@lakedaemon.net
Link: http://lkml.kernel.org/r/20141203121803.5936.35881.sendpatchset@w520
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This adds vendor prefix and root compatible property for following boards
- Firefly, Firefly-RK3288 boards (both beta and mass production version)
- ChipSPARK, Rayeager PX2 board
PX2 SoC is fully compatible with RK3066.
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Other drivers are following the following compatible string format for dts:
s/_/-/
Because some devices may still use the previous string, the new corrected
string is added to the of_device_id table.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Other drivers are following the following compatible string format for dts:
s/_/-/
Because some devices may still use the previous string, the new corrected
string is added to the of_device_id table.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
As no property for phy regulator was documented in this dt-binding documentation,
this commit adds an entry for the optional property phy-supply.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CLK_S_ICN_REG_0 hasn't existed for a while now. This was renamed
over a few commits, then finally removed in commit 5aa02b9 (ARM:
STi: DT: STiH415: Remove unused CLK_S_ICN_REG_0 fixed clock).
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch replaces all custom samsung,power-domain dt
properties with generic power domain bindings and updates
documentation Samsung's devices referring to old binding.
Suggested-by: Kevin Hilman <khilman@kernel.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
[javier.martinez@collabora.co.uk: tested on the Exynos5800 Peach Pi Chromebook]
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Merge "arm64: Add initial Tegra support" from Thierry Reding:
This adds support for the Tegra132 SoC, which is essentially a Tegra124
with a dual Denver CPU complex instead of the quad-Cortex-A15. There is
not much here, only the Kconfig entries, but it will allow us to more
easily get subsequent patches in (many of which have already been sent
for review).
* tag 'tegra-for-3.20-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: Add Tegra132 support
soc: tegra: Add thermal reset (thermtrip) support to PMC
ARM: tegra: Add PMC thermtrip programming to Jetson TK1 device tree
of: Add descriptions of thermtrip properties to Tegra PMC bindings
soc/tegra: pmc: Add Tegra132 support
soc/tegra: fuse: Add Tegra132 support
soc/tegra: fuse: Constify tegra_fuse_info structures
soc/tegra: Add Tegra132 support
clocksource: Build Tegra timer on 32-bit ARM only
soc/tegra: pmc: restrict compilation of suspend-related support to ARM
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull devicetree bug fixes and documentation updates from Grant Likely:
"A few bugfixes for the new DT overlay feature, documentation updates,
spelling corrections, and changes to MAINTAINERS. Nothing earth
shattering here"
* tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux:
of/unittest: Overlays with sub-devices tests
of/platform: Handle of_populate drivers in notifier
of/overlay: Do not generate duplicate nodes
devicetree: document the "qemu" and "virtio" vendor prefixes
devicetree: document ARM bindings for QEMU's Firmware Config interface
Documentation: of: fix typo in graph bindings
dma-mapping: fix debug print to display correct dma_pfn_offset
of: replace Asahi Kasei Corp vendor prefix
ARM: dt: GIC: Spelling s/specific/specifier/, s/flaggs/flags/
dt/bindings: arm-boards: Spelling s/pointong/pointing/
MAINTAINERS: Update DT website and git repository
MAINTAINERS: drop DT regex matching on of_get_property and of_match_table
Merge "ARM: tegra: Core code changes for v3.20" from Thierry Reding:
This contains a couple of preparatory patches for 64-bit support. A new
feature is implemented in the power-management controller which allows
it to switch off the SoC if it overheats.
* tag 'tegra-for-3.20-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc: tegra: Add thermal reset (thermtrip) support to PMC
ARM: tegra: Add PMC thermtrip programming to Jetson TK1 device tree
of: Add descriptions of thermtrip properties to Tegra PMC bindings
soc/tegra: pmc: Add Tegra132 support
soc/tegra: fuse: Add Tegra132 support
soc/tegra: fuse: Constify tegra_fuse_info structures
soc/tegra: Add Tegra132 support
clocksource: Build Tegra timer on 32-bit ARM only
soc/tegra: pmc: restrict compilation of suspend-related support to ARM
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "ARM: imx: device tree changes for 3.20" from Shawn Guo:
The i.MX device tree update for 3.20:
- Update i.MX6 operating-points setting in device tree to match the
latest i.MX6 data sheet
- Add i.MX6SX sabreauto board support
- Add imx6dl-udoo board support based off imx6q-udoo
- Update sabrelite board to include I2C and HDMI support
- Update the VPU compatible strings to also use cnm,coda<model>
- Remove the ocram clock from the VPU node, as the clock is already
provided inside the ocram node
- Add system reset controller and syscon-reboot for VF610
- Update VF610 device tree to use zero based naming for GPIO nodes,
so that the number scheme matches hardware manual
- A number of random device additions like watchdog for VF610, sahara
for i.MX53, QSPI for imx6sx-sdb board, etc.
Note: the branch imx/soc was merged into imx/dt because the SNVS device
tree node needs to refer to the new clock ID added by the imx/soc patch.
* tag 'imx-dt-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (28 commits)
ARM: dts: imx28-evk: remove duplicate property
ARM: vf610: use zero based naming for GPIO nodes
ARM: dts: imx6q: enable dma for ecspi5
ARM: dts: vfxxx: Add SNVS node
ARM: imx: clk-vf610: Add clock for SNVS
ARM: imx: clk-vf610: Add clock for UART4 and UART5
ARM: imx: drop CPUIDLE_FLAG_TIME_VALID from cpuidle-imx6sx
ARM: dts: imx6dl-udoo: Add board support based off imx6q-udoo
ARM: imx: support arm power off in cpuidle for i.mx6sx
ARM: imx: remove unnecessary setting for DSM
ARM: dts: imx6sx: add i.mx6sx sabreauto board support
ARM: dts: imx6sx-sdb: Add QSPI support
ARM: dts: imx6qdl: Remove OCRAM clock from VPU node
ARM: imx: apf51dev: add gpio-backlight support
ARM: imx: correct the hardware clock gate setting for shared nodes
ARM: imx: pllv3: add shift for frequency multiplier
ARM vf610: add compatibilty strings of supported Vybrid SoC's
ARM: i.MX53: dts: add sahara module
ARM: dts: imx6dl: correct cpufreq volt/freq table
ARM: dts: imx6q: update cpufreq volt/freq table
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "ARM: imx: soc changes for 3.20" from Shawn Guo:
The i.MX SoC changes for 3.20:
- Add .disable_unused function hook for shared gate clock to ensure
the clock tree use count matches the hardware state
- Add a deeper idle state for i.MX6SX cpuidle driver powering off the
ARM core
- One correction on i.MX6Q esai_ipg parent clock setting
- Add a missing iounmap call for imx6q_opp_check_speed_grading()
- Add missing clocks for VF610 UART4, UART5 and SNVS blocks
- Expand VF610 device tree compatible matching table to cover more
Vybrid family SoCs
- Expand i.MX clk-pllv3 a bit with the shift for frequency multiplier
to support Vybrid's USB PLL oddity
* tag 'imx-soc-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: clk-imx6q: refine esai_ipg's parent
ARM i.MX6q: unmap memory mapped at imx6q_opp_check_speed_grading()
ARM: imx: clk-vf610: Add clock for SNVS
ARM: imx: clk-vf610: Add clock for UART4 and UART5
ARM: imx: drop CPUIDLE_FLAG_TIME_VALID from cpuidle-imx6sx
ARM: imx: support arm power off in cpuidle for i.mx6sx
ARM: imx: remove unnecessary setting for DSM
ARM: imx: correct the hardware clock gate setting for shared nodes
ARM: imx: pllv3: add shift for frequency multiplier
ARM vf610: add compatibilty strings of supported Vybrid SoC's
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "mvebu/dt #2" from Andrew Lunn:
Second set of dt patches for mvebu for v3.20.
* tag 'mvebu-dt-3.20-2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: make DTS comments reflect DEBUG_LL changes
ARM: mvebu: Armada 385 GP: Add regulators to the SATA port
ARM: Kirkwood: Added support for pogoplug e02 (pink/gray)
ARM: mvebu: fix compatible strings of MBus on Armada 375 and Armada 38x
dt: bindings: update mvebu-mbus DT binding with new compatible properties
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "ARM: rockchip: soc updates for v3.20" from Heiko Stübner:
SoC parts of basic suspend support and removal of
Cortex-A9 reference from the machine name.
* tag 'v3.20-rockchip-soc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: rockchip: remove cpu-core name from machine name
ARM: rockchip: Add pmu-sram binding
ARM: rockchip: add suspend and resume for RK3288
Signed-off-by: Olof Johansson <olof@lixom.net>
Add i2c-mux-idle-disconnect device tree property to PCA954x mux driver. The new
property forces the multiplexer to disconnect child buses in idle state. This is
used, for example, when there are several multiplexers on the same bus and the
devices on the underlying buses might have same I2C addresses.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nsn.com>
[wsa: added a newline]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Hardware-triggered thermal reset requires configuring the I2C
reset procedure. This configuration is read from the device tree,
so document the relevant properties in the binding documentation.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add binding for the Qualcomm Resource Power Manager (RPM) found in 8660,
8960 and 8064 based devices.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This adds the devicetree binding documentation for the LTC2941 and LTC2943
driver. These are I2C connected battery gas gauge ICs.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The register bit fields are a little different, so add an entry and a
compatible string to accommodate them.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Backmerge Linus tree after rc5 + drm-fixes went in.
There were a few amdkfd conflicts I wanted to avoid,
and Ben requested this for nouveau also.
Conflicts:
drivers/gpu/drm/amd/amdkfd/Makefile
drivers/gpu/drm/amd/amdkfd/kfd_chardev.c
drivers/gpu/drm/amd/amdkfd/kfd_mqd_manager.c
drivers/gpu/drm/amd/amdkfd/kfd_priv.h
drivers/gpu/drm/amd/include/kgd_kfd_interface.h
drivers/gpu/drm/i915/intel_runtime_pm.c
drivers/gpu/drm/radeon/radeon_kfd.c
The pogoplug differs from the SheevaPlug only by a
few details, but especially in the led assignments.
This patch was tested under Gentoo Linux and is
based on dts files from Arch Linux ARM and OpenWrt.
Suggested-by: Felix Kaechele <heffer@fedoraproject.org>
Suggested-by: Oleg Rakhmanov <moonman.ca@gmail.com>
Signed-off-by: Christoph Junghans <ottxor@gentoo.org>
[Andrew Lunn <andrew@lunn.ch>: Fixed subject line]
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
This patch enable the last big hardware feature of my driver: the
connector for panel.
Like for HMDI and HDA, Digital Video Out (DVO) create brige, encoder
and connector
drm objects.
* 'drm-sti-next-add-dvo' of git://git.linaro.org/people/benjamin.gaignard/kernel:
drm: sti: add DVO output connector
Merge "ARM: STi: SoC changes for v3.20, round 1" from Maxime Coquelin:
Highlights:
-----------
- Add support for STiH418 SoC
* tag 'sti-soc-for-v3.20-1' of git://git.stlinux.com/devel/kernel/linux-sti:
ARM: STi: Add STiH418 SoC support
Signed-off-by: Olof Johansson <olof@lixom.net>
Add dts file for Hisilicon hip01 ca9x2 board
Signed-off-by: Wang Long <long.wanglong@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
[olof: Folded in smp enable-method from a different patch]
Signed-off-by: Olof Johansson <olof@lixom.net>
Based on Arnds review comments here https://lkml.org/lkml/2014/11/13/161,
update the phy driver to not use the reg property to access the sysconfig
register offsets.
This is because other phy's (miphy28, miphy365) have a combination of
memory mapped registers and sysconfig control regs, and we shouldn't
be mixing address spaces in the reg property. In addition we would
ideally like the sysconfig offsets to be passed via DT in a uniform way.
This new method will also allow us to support devices which have sysconfig
registers in different banks more easily and it is also analagous to how
keystone and bcm7745 platforms pass there syscon offsets in DT.
This breaks DT compatibility, but this platform is considered WIP, and
is only used by a few developers who are upstreaming support for it.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Based on Arnds review comments here https://lkml.org/lkml/2014/11/13/161,
update the miphy28lp phy driver to access sysconfig register offsets via
syscfg dt property.
This is because the reg property should not be mixing address spaces like
it does currently for miphy28lp. This change then also aligns us to how other
platforms such as keystone and bcm7445 pass there syscon offsets via DT.
I have updated the miphy28lp phy driver same way as Peter's implementation.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The Atmel HLCDC (HLCD Controller) IP available on some Atmel SoCs (i.e.
at91sam9n12, at91sam9x5 family or sama5d3 family) provides a display
controller device.
The HLCDC block provides a single RGB output port, and only supports LCD
panels connection to LCD panels for now.
The atmel,panel property link the HLCDC RGB output with the LCD panel
connected on this port (note that the HLCDC RGB connector implementation
makes use of the DRM panel framework).
Connection to other external devices (DRM bridges) might be added later by
mean of a new atmel,xxx (atmel,bridge) property.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Jonathan writes:
First round of IIO new drivers, cleanups and functionality for the 3.20 cycle take 2
Updated pull request with Daniel's fix on top for the power management
Kconfig changes that had snuck in since last update of the IIO tree
worked it's way through from mainline.
Original pull message
New device support
* jsa1212 proxmity / ambient light sensor
* SM08500 supported added to the kxcjk-1013 accelerometer driver
* KMX61 Accelerometer/Magnetometer. This took a somewhat rocky path
being first merged, then reverted for a rewrite after a discussion of
how to support additional functionality and finally being merged prior
to some last reviews coming in, with resultant follow up patches.
* Freescale mma9551l driver (minor follow up warning supression patch).
* Semtech SX9500 proximity device driver.
* ak8975 gains support for ak09911 and ak09912 and drop the standalone driver
for the ak09911.
New functionality
* Dummy driver gains some virtual registers making it more flexible.
* IIO_ACTIVITY channel types, with modifiers running, walking etc. This is
to support on chip motion clasifiers. As such it is in the form of a
confidence percentage. The only devices so far only do binary decisions
but this gives us room when other devices give more nuanced clasification.
* IIO_EV_DIR_NONE type for events where there is no obvious direction.
First case is step detection.
* IIO_STEPS channel type for pedometers.
* ENABLE mask element used to control turning on counting types such as
the pedometer that need a 'start point'.
* INSTANCE event type to support things that happen once.
* info element for height calibration (used in various motion estimation
algorithms). Note heigh tof use
* dummy driver demonstration of the use of all the new bits above.
* event monitor support for the new events.
* inv_mpu6050 gains an i2c mux to allow bypassing the device to access
additional devices connected on the other side of it. Note that in
Windows these are handled by firmware on the device and not exposed
directly.
* inv_mpu6050 gains ACPI enumeration.
* inkern interface gains iio_write_channel_raw to allow in kernel users
of DAC functionality via a simple wrapper.
* Document input current readings in the ABI docs.
* Add an error message when we get an out of range error in device tree
processing for the in kernel interfaces. Basically a device tree debugging
aid.
* Add a sanity check that a scan index for a channel is unique during
registration. There to help catch bugs as this should never happen
in a bug free driver.
Cleanups and fixlets
A rework of buffer registration from Lars - a precursor to some other
upcoming new stuff (a few patches from others rolled in here as well).
* Ensure all drivers register the same channels for the device and buffer.
* Move buffer registration into the core rather than using the old
two step approach. Now we have simple ways of using a unified set channels
for both without requiring channels be exposed by both interface, this
removes a fair bit of boilerplate.
* Stop sca3000 and ad5933 (both in staging) enabling buffer channels by
default. It has long be convention in IIO to startup with no channels
enabled and leave it up to userspace to say what goes in the buffer.
Getting rid of these allows us to drop export of iio_scan_mask_set.
* Drop get_bytes_per_datum from iio_buffer_access_funcs as not been used
for a while.
* Allocate standard buffer attributes in the core rather than in every
driver with a buffer.
* Make the length attribute read only when a driver is not able to set
the length.
* Drop the get_length callback for buffers as it is already available in
struct iio_buffer.
* Drop an unused arguement form iio_kfifo_allocate and add devm allocator
for it.
* some kconfig entries gain anotation with the resulting module name.
* Fix a resulting compile issue in dummy driver due to a stub taking
wrong parameters as a result of the above rework.
* Fix an off by 2 error in copying the core assigned buffer attributes.
Other cleanups,
* Trivial space before comma fixups.
* ak8975 fixlets - none critical. Rework to allow more device support.
* Drop unnecessary sizeof(u8) calls.
* bmp280 - refactor the compensation code to reduce copy operations and
code length. A second patch futher optimized this and performed some
other minor cleanups.
* kxcjk-1013 - various power control cleanups to avoid unnecessary enable
/ disable of device. Make sure it is only controlled at all if CONFIG_PM
is enabled. Also som cleanups of error paths.
* Small cleanups in adf4530 driver - pointless message and unnecessary braces.
* Clarifiy the proximity ABI docs to make it clear it should get bigger
as we move futher away.
* Drop a misleading comment form industrialio-core.c
* Trivial white space cleanups.
* sca3000 looses an unused debug function.
* Fix char unsigned ordering in ad8366
* Increase the sleep time in ad9523 to make it predictable (value didn't
really matter so make it more than 20 msecs)
* mxs-lradc touchscreen property cleanups in device tree are fixed to ensure
the meet all the 'interesting' documentation.
* A couple of cleanups for the staging ad5933 driver to avoid unnecessary
conversion to a processed temperature vlaue in kernel and remove
platform data form the state structure as not needed after probe.
* Fix a wrong scale factor in the docs.
Misc
* Add IIO include files to the maintainers entry.
imx-drm mode fixup support, imx-hdmi bridge conversion and imx-drm cleanup
- Implement mode_fixup for a DI vertical timing limitation
- Use generic DRM OF helpers in DRM core
- Convert imx-hdmi to dw_hdmi drm_bridge and add rockchip
driver
- Add DC use counter to fix multi-display support
- Simplify handling of DI clock flags
- A few small fixes and cleanup
* tag 'imx-drm-next-2015-01-09' of git://git.pengutronix.de/git/pza/linux: (26 commits)
imx-drm: core: handling of DI clock flags to ipu_crtc_mode_set()
gpu: ipu-di: Switch to DIV_ROUND_CLOSEST for DI clock divider calc
gpu: ipu-v3: Use videomode in struct ipu_di_signal_cfg
imx-drm: encoder prepare/mode_set must use adjusted mode
imx-drm: ipuv3-crtc: Implement mode_fixup
drm_modes: add drm_display_mode_to_videomode
gpu: ipu-di: remove some non-functional code
gpu: ipu-di: Add ipu_di_adjust_videomode()
drm: rockchip: export functions needed by rockchip dw_hdmi bridge driver
drm: bridge/dw_hdmi: request interrupt only after initializing the mutes
drm: bridge/dw_hdmi: add rockchip rk3288 support
dt-bindings: Add documentation for rockchip dw hdmi
drm: bridge/dw_hdmi: add function dw_hdmi_phy_enable_spare
drm: bridge/dw_hdmi: clear i2cmphy_stat0 reg in hdmi_phy_wait_i2c_done
drm: bridge/dw_hdmi: add mode_valid support
drm: bridge/dw_hdmi: add support for multi-byte register width access
dt-bindings: add document for dw_hdmi
drm: imx: imx-hdmi: move imx-hdmi to bridge/dw_hdmi
drm: imx: imx-hdmi: split phy configuration to platform driver
drm: imx: imx-hdmi: convert imx-hdmi to drm_bridge mode
...
* 'drm/next/du' of git://linuxtv.org/pinchartl/fbdev:
drm: rcar-du: Implement support for interlaced modes
drm: rcar-du: Clamp DPMS states to on and off
drm: rcar-du: Enable hotplug detection on HDMI connector
drm: rcar-du: Output HSYNC instead of CSYNC
drm: rcar-du: Add support for external pixel clock
drm: rcar-du: Refactor DEFR8 feature
drm: rcar-du: Remove LVDS and HDMI encoders chaining restriction
drm: rcar-du: Configure pitch for chroma plane of multiplanar formats
drm: rcar-du: Don't fail probe in case of partial encoder init error
drm: adv7511: Remove interlaced mode check
Since in SAMA5D4 chip, the PMECC can correct bit flips in erased page.
So we add a DT property to indicate this hardware character.
If the PMECC support correct bitflip erased page (all data are 0xff).
Then we can use the PMECC correct the page and skip the erased page
check.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Freescale introduced new ARM-based socs which using the compatible
clock IP block with PowerPC-based socs'. So this driver can be used
on both platforms.
Updated relevant descriptions and renamed this driver to better
represent its meaning and keep the function of driver untouched.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
On dm816x the clocks are sourced from a FAPLL (Flying Adder PLL)
that does not seem to be used on the other omap variants.
There are four instances of the FAPLL on dm816x that each have three
to seven child synthesizers.
I've set up the FAPLL as a single fapll.c driver. Later on we could
potentially have the PLL code generic. To do that, we would have to
consider the following:
1. Setting the PLL to bypass mode also sets the child synthesizers
into bypass mode. As the bypass rate can also be generated by
the PLL in regular mode, there's no way for the child synthesizers
to detect the bypass mode based on the parent clock rate.
2. The PLL registers control the power for each of the child
syntheriser.
Note that the clocks are currently still missing the set_rate
implementation so things are still running based on the bootloader
values. That's OK for now as most of the outputs have dividers and
those can be set using the existing TI component clock code.
I have verified that the extclk rates are correct for a few clocks,
so adding the set_rate support should be fairly trivial later on.
This code is partially based on the TI81XX-LINUX-PSP-04.04.00.02
patches published at:
http://downloads.ti.com/dsps/dsps_public_sw/psp/LinuxPSP/TI81XX_04_04/04_04_00_02/index_FDS.html
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
On the A80 SoC, the 4 mmc controllers each have a separate register
controlling their register access clocks and reset controls. These
registers in turn share a ahb clock gate and reset control.
This patch adds a platform device driver for these controls. It
requires both clocks and reset controls to be available, so using
CLK_OF_DECLARE might not be the best way.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Document new device tree bindings for Maxim 77693 charger driver.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Document the fact that the trigger signal is now optional, and describe
the behavior when this is used.
While at it, fix a typo, and paraphrase a sentence to be less platform
specific.
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
