[Why/How]
LTTPR are required to program DPCD 0000Eh to 0x4 (16ms) upon AUX read
reply to this register. Since old Sinks witih DPCD rev 1.1 and earlier
may not support this register, assume the mandatory value is programmed
by the LTTPR to avoid AUX timeout issues.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Urgent latency adjustment was disabled on DCN35 due to issues with P0
enablement on some platforms. Without urgent latency, underflows occur
when doing certain high timing configurations. After testing, we found
that reenabling urgent latency didn't reintroduce p0 support on multiple
platforms.
[How]
renable urgent latency on DCN35 and setting it to 3000 Mhz.
This reverts commit 3412860cc4.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Nicholas Susanto <nsusanto@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Large stack size observed in DCN4 mode support when compiling with clang.
Additional instrumentation added by compiler adds to stack size.
dml_core_mode_support ends up going over the stack size limit
due to the size of the function.
[How]
Move checks and calculations for prefetch to its own function.
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Austin Zheng <Austin.Zheng@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If the dummy values in `populate_dummy_dml_surface_cfg()` aren't updated
then they can lead to a divide by zero in downstream callers like
CalculateVMAndRowBytes()
[How]
Initialize dummy value to a value to avoid divide by zero.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For some pixel clock margin sensitive external monitor,
we could not keep original DP ref clock for the ASICs
supported SSC DP ref clock.
[How]
From slicon design team's comment,
we have to apply the adjusted DP ref clock for
DP devices.
DP 128b (DP2) signals uses the DTBCLK not DP ref.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Yiling Chen <yi-ling.chen2@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Probably a cut and paste error from using get_integrated_info_v8's comment.
This has to be get_integrated_info_v9
Signed-off-by: Alexandre Demers <alexandre.f.demers@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
i2c_speed_in_khz was set twice with the same values. Looking at other DCE
versions, we probably wanted to set the value for i2c_speed_in_khz_hdcp.
Signed-off-by: Alexandre Demers <alexandre.f.demers@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The prefix dce110 is used on all functions, but init_pipes() and
init_hw(). Under DCN, these sames functions are prefixed.
Let's keep thing coherent.
Signed-off-by: Alexandre Demers <alexandre.f.demers@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Classify DCE6 resource and sequencer as they are for other DCE versions
Put dce60_resource.c and .h under amd/display/dc/resource/dce60
Put and rename dce60_hw_sequencer.c and .h under amd/display/dc/hwss/dce60
v2: fix build when CONFIG_DRM_AMD_DC_SI=n (Alex)
Signed-off-by: Alexandre Demers <alexandre.f.demers@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In DCE6, DCE8, DCE10, DCE11, "hdp" is replaced by "hpd" and
replace "type" by "hpd" for a uniform parameter naming usage across DCEs.
In link_factory.c, there is a missing "p" to "types"
Signed-off-by: Alexandre Demers <alexandre.f.demers@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Summary:
* Optimize custom brightness curve
* Correct SSC enable detection for DCN351
* Turn off eDP lcdvdd and backlight if not required
* Use DMUB Fused IO interface for HDCP
* Extend eDP-on-DP1 quirk list
Reviewed-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Taimur Hassan <Syed.Hassan@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
fix was previously in 25.20 but was reverted out as it was accompanied
by other changes that caused regression.
[why&how]
Disabling dtb as the dto src during dpms off relies on in the same
instance being able to also alter the dto src bit to dpref (or not dtb
in general), but this was recently changed to only take place in
dcn31_program_pix_clk, as that is where we want to perform any dto src
changes because tg is off at that point, it is unsafe to do that
elsewhere. What this means is now instead of disabling dtb as dto src
and modifying source bit, we are left with the configuration for a given
tg that specifies dtb as dto src and dtb dto en simultaneously is unset.
dcn31_program_pix_clk can rectify this but its possible for us to
perform some tg dependant operation that would simply hang because when
we go to enable say crtc then, the clk we specify as dto src is "off" en
bit is cleared, source bit was never changed, and program_pix_clk hasnt
been called yet (as apart of dpms on)
We cant disable it as dto src during dpms off if we want the luxury of
performing tg dependant operation during dpms off and before dpms on.
Reviewed-by: Yihan Zhu <yihan.zhu@amd.com>
Signed-off-by: Ausef Yousof <Ausef.Yousof@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why&how]
It is possible for an update to acquire otg lock and begin programming
while the previous update has not completed and its values have not
latched. The correct way to go about this is to wait until the vupdate
pulses so we can be sure that previous updates have latched and we can
continue with the current update pipe programming, otherwise during
consecutive full updates we will have corruption flash on the screen.
The corruption flash occurs specifically on configs that require odm
combine, and its local to a specific pipe (will not flash across whole
screen). This ticket is across the otg slave, but it may also appear
across master.
Reviewed-by: Leo Chen <leo.chen@amd.com>
Signed-off-by: Ausef Yousof <Ausef.Yousof@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A variety of the 3DLUT handling functions check
`debug.enable_mem_low_power.bits.cm` both in the caller and function.
This is unnecessary overhead.
[How]
For each of them reduce to just checking just in caller or function.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HDCP locality check has strict timing requirements, currently broken
due to reliance on msleep which does not guarantee accuracy.
The PR moves the write-poll-read sequence into DMUB using new generic
Fused IO interface, where the timing accuracy is greatly improved.
New flow is enabled using DCN resource capability bit (none for now),
or using a debug flag.
[How]
* Extended mod_hdcp_config with new function for requesting DMUB
to execute a sequence of fused I2C/AUX commands and synchronously
wait until an outbox reply arrives or a timeout expires.
* If the timeout expires, send an abort to DMUB.
* Update HDCP to use the DMUB for locality check if supported.
* Add DC_HDCP_LC_FORCE_FW_ENABLE and DC_HDCP_LC_ENABLE_SW_FALLBACK.
* Make the first enable new flow regardless of resource capabilities.
* Make the second enable fallback to old SW flow.
* Clean up makefile source file listings for easier updates.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Dominik Kaszewski <dominik.kaszewski@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Due to very small clock register delta between DCN35 and DCN351, clock
spread is being checked on the wrong register for DCN351, causing the
display driver to believe that DPREFCLK downspread to be disabled when
in some stacks it is enabled. This causes the clock values for audio to
be incorrect.
[How]
Both DCN351 and DCN35 use the same clk_mgr, so we modify the DCN35
function that checks for SSC enable to read CLK6 instead of CLK5 when
using DCN351. This allows us to read for DPREFCLK downspread correctly
so the clock can properly compensate when setting values.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Kevin Gao <kevin.gao3@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Static analysis shows that pointer "timing" cannot be NULL because it
points to the object "struct dc_crtc_timing".
Remove the extra NULL check. It is meaningless and harms the readability
of the code.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Andrey Vatoropin <a.vatoropin@crpt.ru>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY&HOW]
DCN401 uses a different structure to store the VStartup offset used to
calculate the VUpdate position, so adjust the calculations to use this
value.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DCN4+ supports a new register based mailbox for sending messages
from host to DMCUB. This mailbox supports 64 byte commands, which makes
it compatible with the same structure as the frame buffer based mailbox.
[HOW]
The intention for reg_inbox0 is to be slot in replacement for the frame
buffer based mailbox (Inbox1). It supports all of the required features:
- Supports all messages handled by FB Inbox1
- Supports multi command batching
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Replay need special policy for the scenario Teams,
add a flag to imply apply special policy or not.
[How]
Add a config option intended for future use for video conferencing applications.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: ChunTao Tso <ChunTao.Tso@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This array was initially defined as size 50. There were array overflow
issues so the size was increased to 100. To ensure such issues are
avoided in the future, the size should be set based on the possible
contents instead of an arbitrary value.
[How]
- upper bound, assume every update occurs on max number of pipes
- define array sizes for function parameters, for static analysis
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Mapping of ODM enum is different for DML2.0 vs DML2.1.
Configs using DML2.1 will incorrectly trigger an assert meant for DML2.0.
[How]
Use if/else to seperate logic between DML2.0 and DML2.1.
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Austin Zheng <Austin.Zheng@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It makes DSC enable when we commit the stream which need
keep power off.And then it will skip to disable DSC if
pipe reset at this situation as power has been off. It may
cause the DSC unexpected enable on the pipe with the
next new stream which doesn't support DSC.
[HOW]
Check the DSC used on current pipe status when update stream.
Skip to enable if it has been off. The operation enable
DSC should happen when set power on.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Paul Hsieh <Paul.Hsieh@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We want to output visual confirm color based on stream.
[HOW]
If visual confirm is for DMUB, use DMUB to get color.
Otherwise, find plane with highest layer index, output visual confirm color
of pipe that contains plane with highest index.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Leo Zeng <Leo.Zeng@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We want to allow the display manager to override the visual
confirm color in DC when required.
[HOW]
Add new visual confirm mode VISUAL_CONFIRM_EXPLICIT, check mode before
setting visual confirm color.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Leo Zeng <Leo.Zeng@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
