[Why]
When link training fails, the phy clock will be disabled. However, in
enable_streams, it is assumed that link training succeeded and the
mux selects the phy clock, causing a hang when a register write is made.
[How]
When enable_stream is hit, check if link training failed. If it did, fall
back to the ref clock to avoid a hang and keep the system in a recoverable
state.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Brendan Tam <Brendan.Tam@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
This version brings along following fixes:
- Use DPM table clk setting for dml2 soc dscclk
- Update static soc table
- Fix incorrect fw_state address in dmub_srv
- Use HW lock mgr for PSR1 when only one eDP
- Revert "Support for reg inbox0 for host->DMUB CMDs"
- Change notification of link BW allocation
- Fix message for support_edp0_on_dp1
- Guard against setting dispclk low for dcn31x
- Prevent VStartup Overflow
- Check pipe->stream before passing it to a function
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Taimur Hassan <Syed.Hassan@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DMUB locking is important to make sure that registers aren't accessed
while in PSR. Previously it was enabled but caused a deadlock in
situations with multiple eDP panels.
[HOW]
Detect if multiple eDP panels are in use to decide whether to use
lock. Refactor the function so that the first check is for PSR-SU
and then replay is in use to prevent having to look up number
of eDP panels for those configurations.
Fixes: f245b400a2 ("Revert "drm/amd/display: Use HW lock mgr for PSR1"")
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3965
Reviewed-by: ChiaHsuan Chung <chiahsuan.chung@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
The response of DP BW allocation is handled in Outbox ISR.
When it failed to request the DP BW allocation, it sent another
DPCD request in Outbox ISR immediately. The DP AUX reply also
uses the Outbox ISR. So, no AUX reply happened in this case.
Change to use HPD IRQ for the notification.
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Cruise Hung <Cruise.Hung@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We should never apply a minimum dispclk value while in
prepare_bandwidth or while displays are active. This is
always an optimizaiton for when all displays are disabled.
[HOW]
Defer dispclk optimization until safe_to_lower = true
and display_count reaches 0.
Since 0 has a special value in this logic (ie. no dispclk
required) we also need adjust the logic that clamps it for
the actual request to PMFW.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Chris Park <chris.park@amd.com>
Reviewed-by: Eric Yang <eric.yang@amd.com>
Signed-off-by: Jing Zhou <Jing.Zhou@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT & HOW]
dp_is_128b_132b_signal dereferences pipe->stream so it is necessary to
check it in advance.
Also fix erroneous spaces and move a variable declaration to top.
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We are trying to get rid of all multiplications from allocation
functions to prevent integer overflows. Here the multiplication is
probably safe, but using kcalloc() is more appropriate and improves
readability. This patch has no effect on runtime behavior.
Reviewed-by: Rodrigo Siqueira <siqueira@igalia.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Ethan Carter Edwards <ethan@ethancedwards.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We are trying to get rid of all multiplications from allocation
functions to prevent integer overflows. Here the multiplication is
probably safe, but using kcalloc() is more appropriate and improves
readability. This patch has no effect on runtime behavior.
Reviewed-by: Rodrigo Siqueira <siqueira@igalia.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Ethan Carter Edwards <ethan@ethancedwards.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We are trying to get rid of all multiplications from allocation
functions to prevent integer overflows. Here the multiplication is
probably safe, but using kcalloc() is more appropriate and improves
readability. This patch has no effect on runtime behavior.
Reviewed-by: Rodrigo Siqueira <siqueira@igalia.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Ethan Carter Edwards <ethan@ethancedwards.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We are trying to get rid of all multiplications from allocation
functions to prevent integer overflows. Here the multiplication is
probably safe, but using kcalloc() is more appropriate and improves
readability. This patch has no effect on runtime behavior.
Reviewed-by: Rodrigo Siqueira <siqueira@igalia.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Ethan Carter Edwards <ethan@ethancedwards.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For some VR headsets with large blanks, it's possible
to overflow the OTG_VSTARTUP_PARAM:VSTARTUP_START
register. This can lead to incorrect DML calculations
and underflow downstream.
[How]
Min the calcualted max_vstartup_lines with the max
value of the register.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Ryan Seto <ryanseto@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
stream->adjust will be overwritten by update->crtc_timing_adjust.
We should set update->crtc_timing_adjust->timing_adjust_pending
and then overwrite stream->adjust.
Reset update->crtc_timing_adjust->timing_adjust_pending after
the assignment.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Zhongwei Zhang <Zhongwei.Zhang@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
In some cases the remain de-tile buffer segments will be greater
than zero if we don't add the non-top pipe to calculate, at
this time the override de-tile buffer size will be valid and used.
But it makes the de-tile buffer segments used finally for all of pipes
exceed the maximum.
[HOW]
Add the non-top pipe to calculate the remain de-tile buffer segments.
Don't set override size to use the average according to pipe count
if the value exceed the maximum.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Zhikai Zhai <zhikai.zhai@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Sometimes visual confirm color is updated, but the
background color is not changed. This causes visual
confrim to show incorrect colors.
[HOW]
Update background color when visual confirm color changes.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Leo Zeng <Leo.Zeng@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
A warning message "WARNING: CPU: 4 PID: 459 at ... /dc_resource.c:3397
calculate_phy_pix_clks+0xef/0x100 [amdgpu]" occurs because the
display_color_depth == COLOR_DEPTH_141414 is not handled. This is
observed in Radeon RX 6600 XT.
It is fixed by assigning pix_clk * (14 * 3) / 24 - same as the rests.
Also fixes the indentation in get_norm_pix_clk.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DCN4+ supports a new register based mailbox for sending messages
from host to DMCUB. This mailbox supports 64 byte commands, which makes
it compatible with the same structure as the frame buffer based mailbox.
[HOW]
The intention for reg_inbox0 is to be slot in replacement for the frame
buffer based mailbox (Inbox1). It supports all of the required features:
- Supports all messages handled by FB Inbox1
- Supports multi command batching
Reviewed-by: Joshua Aberback <joshua.aberback@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
The clear_dsc_setting at boot logic was based on dcn version
check.
As such new ASIC lost this DSC clear up logic, change the
assumption to BIOS support eDP DSC for new ASIC.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why/How]
DP spec has been updated recently to make regulated autonomous mode more
well-defined. In case any PCON vendors choose to implement regulated
autonomous mode in the future, pre-emptively add handling for the
regulated autonomous mode based on current spec.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When analyzing some crash dumps, not all of the expected DMUB info was
available, so we want to add in-object storage for this data.
[How]
- dmub_srv_debug (renamed to dmub_timeout_info) is already a member of
dmub_diagnostic_data, therefore keep a dmub_diagnostic_data directly in
dmub_srv
- use dmub_srv->debug when collecting diagnostic info instead of stack
object to allow for easy inspection in crash dumps
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Starting from 6.11, AMDGPU driver, while being loaded with amdgpu.dc=1,
due to lack of .is_two_pixels_per_container function in dce60_tg_funcs,
causes a NULL pointer dereference on PCs with old GPUs, such as R9 280X.
So this fix adds missing .is_two_pixels_per_container to dce60_tg_funcs.
Reported-by: Rosen Penev <rosenp@gmail.com>
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3942
Fixes: e6a901a008 ("drm/amd/display: use even ODM slice width for two pixels per container")
Signed-off-by: Aliaksei Urbanski <aliaksei.urbanski@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
print__rq_dlg_params_st() was added in 2017 by
commit 061bfa06a4 ("drm/amdgpu/display: Add dml support for DCN")
but has remained unused.
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
pre_surface_trace() has been unused since 2017's
commit 745cc746da ("drm/amd/display: remove
dc_pre_update_surfaces_to_stream from dc use")
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
- Various cleanups to amdgpu dm
- Add DP tunneling IRQ handler
- Fix display corruption for dcn35
- Fix dmcub reset problem
- Adjust BW determination for PCON
- DIO encoder refactor
- Fix performance with SubVP under gaming
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Taimur Hassan <Syed.Hassan@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
USB4 DP BW Allocation uses DP_TUNNELING_IRQ to indicate the status update.
The DP_TUNNELING_IRQ is defined in LINK_SERVICE_IRQ_VECTOR_ESI0. When
receiving DP HPD IRQ in USB4, read the LINK_SERVICE_IRQ_VECTOR_ESI0.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Cruise Hung <Cruise.Hung@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We want to add a visual confirm mode for DCC and MCache for
debugging purpose.
[HOW]
color pipes based on whether DCC is enabled and what MCache id
is used.
black - DCC disabled
red - DCC enabled
grey - 2 different MCaches used
other colors - 1 MCache used
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Leo Zeng <Leo.Zeng@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why/How]
Certain PCON will clear the FRL_MODE bit despite supporting the link BW
indicated in the other bits.
Thus, skip checking the FRL_MODE bit when interpreting the
hdmi_encoded_link_bw struct.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
These are left required changes for dio encoder refactor.
[HOW]
1. original logic is separated by config option
2. new link encoder dp enable/disable code for dcn35
3. process fec only for DP 8b10b encoding
Reviewed-by: Cruise Hung <cruise.hung@amd.com>
Signed-off-by: Peichen Huang <PeiChen.Huang@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY&HOW]
P-state type would remain on previously used when unsupported which
causes confusion in logging and visual confirm, so set back to zero
when unsupported.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When SubVP is active the HW cursor size is limited to 64x64, and
anything larger will force composition which is bad for gaming on
DCN3.2 if the game uses a larger cursor.
[how]
If HW cursor is requested, typically by a fullscreen game, do not
enable SubVP so that up to 256x256 cursor sizes are available for
DCN3.2.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Aric Cyr <Aric.Cyr@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is a type mismatch between what CalculateDynamicMetadataParameters()
takes and what is passed to it. Currently this function accepts several
args as signed long but it's called with unsigned integers and integer. On
some systems where long is 32 bits and one of these unsigned int params is
greater than INT_MAX it may cause passing input params as negative values.
Fix this by changing these argument types from long to unsigned int and to
int respectively. Also this will align the function's definition with
similar functions in other dcn* drivers.
Found by Linux Verification Center (linuxtesting.org) with Svace.
Fixes: 6725a88f88 ("drm/amd/display: Add DCN3 DML")
Signed-off-by: Vitaliy Shevtsov <v.shevtsov@mt-integration.ru>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Null pointer dereference issue could occur when pipe_ctx->plane_state
is null. The fix adds a check to ensure 'pipe_ctx->plane_state' is not
null before accessing. This prevents a null pointer dereference.
Found by code review.
Fixes: 3be5262e35 ("drm/amd/display: Rename more dc_surface stuff to plane_state")
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The last use of optc3_fpu_set_vrr_m_const() was removed in 2022's
commit 64f991590f ("drm/amd/display: Fix a compilation failure on PowerPC
caused by FPU code")
which removed the only caller (with a similar) name.
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
All dce command_table_helper's shares a copy-pasted collection
of copy-pasted functions, which are: phy_id_to_atom,
clock_source_id_to_atom_phy_clk_src_id, and engine_bp_to_atom.
This patch removes the multiple copy-pasted by moving them to
the command_table_helper.c and make the command_table_helper's
calls the functions implemented by the command_table_helper.c
instead.
The changes were not tested on actual hardware. I am only able
to verify that the changes keep the code compileable and do my
best to to look repeatedly if I am not actually changing any code.
This is the version 4 of the PATCH, fixed comments about
licence in the new files and the matches From email to
Signed-off-by email. Fixed comments about using
command_table_helper instead of creating a dce_common
Signed-off-by: Luan Icaro Pinto Arcanjo <luanicaro@usp.br>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Transitioning from low to high resolutions at high refresh rates caused grey corruption.
During the transition state, there is a period where plane size is based on low resultion
state and ODM slices are based on high resoultion state, causing the entire plane to be
contained in one ODM slice. DML2 would turn off the pipe for the ODM slice with no plane,
causing an underflow since the pixel rate for the higher resolution cannot be supported on
one pipe. This change stops DML2 from turning off pipes that are mapped to an ODM slice
with no plane. This is possible to do without negative consequences because pipes can now
take the minimum viewport and draw with zero recout size, removing the need to have the
pipe turned off.
[How]
In map_pipes_from_plane(), remove "check" that skips ODM slices that are not covered by
the plane. This prevents the pipes for those ODM slices from being freed.
Reviewed-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Signed-off-by: Mike Katsnelson <mike.katsnelson@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
