DMA has been enabled on RP1's UART0, but with mixed success. Transmits
seem to work, but the DMA interface is not well suited to receiving
arbitrary amounts of data. In particular, the PL011 driver is slow to
pass on the received data, batching it into large blocks.
On balance, it's better to just disable the DMA support. As with the
other UARTs, the required runes are left in the DTS as comments.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
A forthcoming overlaycheck update looks for dormant fragments with no
parameters to enable them. The test discovered some real errors, which
this patch fixes, and one case where some fragments aren't yet being
used, which this comments out until they are.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
In addition to the standard reset controller, V3D 7.x requires configuring
the V3D_SMS registers for proper power on/off and reset. Add the new
registers to `v3d_regs.h` and ensure they are properly configured during
device probing, removal, and reset.
This change fixes GPU reset issues on the Raspberry Pi 5 (BCM2712).
Without exposing these registers, a GPU reset causes the GPU to hang,
stopping any further job execution and freezing the desktop GUI. The same
issue occurs when unloading and loading the v3d driver.
Link: https://github.com/raspberrypi/linux/issues/6660
Signed-off-by: Maíra Canal <mcanal@igalia.com>
V3D 7.1 exposes a new register block, called V3D_SMS. As BCM2712 has a
V3D 7.1 core, add a new register item to the list. Similar to the GCA
and bridge register, SMS is optional and should only be added for V3D
7.1 variants.
Cc: Krzysztof Kozlowski <krzk+dt@kernel.org>
Cc: Conor Dooley <conor+dt@kernel.org>
Cc: Nicolas Saenz Julienne <nsaenz@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Maíra Canal <mcanal@igalia.com>
The V3D driver currently determines the GPU tech version (33, 41...)
by reading a register. This approach has worked so far since this
information wasn’t needed before powering on the GPU.
V3D 7.1 introduces new registers that must be written to power on the
GPU, requiring us to know the V3D version beforehand. To address this,
associate each supported SoC with the corresponding VideoCore GPU version
as part of the device data.
To prevent possible mistakes, add an assertion to verify that the version
specified in the device data matches the one reported by the hardware.
If there is a mismatch, the kernel will trigger a warning.
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Similar to commit e4b5ccd392 ("drm/v3d: Ensure job pointer is set to
NULL after job completion"), ensure the job pointer is set to `NULL` when
a job's fence has an error. Failing to do so can trigger kernel warnings
in specific scenarios, such as:
1. v3d_csd_job_run() assigns `v3d->csd_job = job`
2. CSD job exceeds hang limit, causing a timeout → v3d_gpu_reset_for_timeout()
3. GPU reset
4. drm_sched_resubmit_jobs() sets the job's fence to `-ECANCELED`.
5. v3d_csd_job_run() detects the fence error and returns NULL, not
submitting the job to the GPU
6. User-space runs `modprobe -r v3d`
7. v3d_gem_destroy()
v3d_gem_destroy() triggers a warning indicating that the CSD job never
ended, as we didn't set `v3d->csd_job` to NULL after the timeout. The same
can also happen to BIN, RENDER, and TFU jobs.
Signed-off-by: Maíra Canal <mcanal@igalia.com>
The V3D driver still relies on `drm_sched_increase_karma()` and
`drm_sched_resubmit_jobs()` for resubmissions when a timeout occurs.
The function `drm_sched_increase_karma()` marks the job as guilty, while
`drm_sched_resubmit_jobs()` sets an error (-ECANCELED) in the DMA fence of
that guilty job.
Because of this, we must check whether the job’s DMA fence has been
flagged with an error before executing the job. Otherwise, the same guilty
job may be resubmitted indefinitely, causing repeated GPU resets.
This patch adds a check for an error on the job's fence to prevent running
a guilty job that was previously flagged when the GPU timed out.
Note that the CPU and CACHE_CLEAN queues do not require this check, as
their jobs are executed synchronously once the DRM scheduler starts them.
Cc: stable@vger.kernel.org
Fixes: d223f98f02 ("drm/v3d: Add support for compute shader dispatch.")
Fixes: 1584f16ca9 ("drm/v3d: Add support for submitting jobs to the TFU.")
Signed-off-by: Maíra Canal <mcanal@igalia.com>
The previous change to make ov9281 always run in continuous clock
mode causes problems on Pi3 for reasons that aren't fully
understood. Pi4 is quite happy with it.
Change the default back to being non-continuous clock, and add
an override to select continuous clock mode and its slightly
greater max frame rate.
https://forums.raspberrypi.com/viewtopic.php?p=2300215
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Fast transfer mode requires that the first bit of data is clocked with a
rising edge. This can cause extra bits of data to be clocked on hardware
where the clock signal uses a pull-up. This change ensures that clk is
driven low before fast data transfer mode is entered.
Signed-off-by: Richard Oliver <richard.oliver@raspberrypi.com>
In some circumstances, devm_gpiod_get_array_optional() can return
PTR_ERR rather than NULL to indicate failure. Handle these cases.
Signed-off-by: Richard Oliver <richard.oliver@raspberrypi.com>
On Pi5 5, GPIOs 46/48 are made available on the 'CAM/DISP 1' connector as
'CD1_IO0_MICCLK'/'CD1_IO1_MICDAT1'. These GPIOs are not connected on
CM5.
Add hogs for GPIO 46/48 on CM5 to prevent camera drivers from
inadvertently using them when connected to 'CAM/DISP 1'
Signed-off-by: Richard Oliver <richard.oliver@raspberrypi.com>
Support for the RP1 firmware mailbox API is rolling out to Pi 5 EEPROM
images. For most users, the fact that the PIO is not available is no
cause for alarm. Change the message to a warning, so that it does not
appear with "quiet" in cmdline.txt.
Link: https://github.com/raspberrypi/linux/issues/6642
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The mutex used in arducam-pivariety was not properly initialized,
which could lead to undefined behavior. This also caused a NULL
pointer dereference under certain conditions.
This patch ensures the mutex is correctly initialized during probe
and prevents NULL pointer dereferences.
Signed-off-by: Yuriy Pasichnyk <yurijpasichnyk11@gmail.com>
commit 73b42dc69b upstream.
Re-introduce the "split" x2APIC ICR storage that KVM used prior to Intel's
IPI virtualization support, but only for AMD. While not stated anywhere
in the APM, despite stating the ICR is a single 64-bit register, AMD CPUs
store the 64-bit ICR as two separate 32-bit values in ICR and ICR2. When
IPI virtualization (IPIv on Intel, all AVIC flavors on AMD) is enabled,
KVM needs to match CPU behavior as some ICR ICR writes will be handled by
the CPU, not by KVM.
Add a kvm_x86_ops knob to control the underlying format used by the CPU to
store the x2APIC ICR, and tune it to AMD vs. Intel regardless of whether
or not x2AVIC is enabled. If KVM is handling all ICR writes, the storage
format for x2APIC mode doesn't matter, and having the behavior follow AMD
versus Intel will provide better test coverage and ease debugging.
Fixes: 4d1d7942e3 ("KVM: SVM: Introduce logic to (de)activate x2AVIC mode")
Cc: stable@vger.kernel.org
Cc: Maxim Levitsky <mlevitsk@redhat.com>
Cc: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Link: https://lore.kernel.org/r/20240719235107.3023592-4-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
[JH: fixed conflict with vmx_x86_ops reshuffle due to missing commit 5f18c642ff]
Signed-off-by: James Houghton <jthoughton@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4b7c3f6d04 upstream.
Ignore the userspace provided x2APIC ID when fixing up APIC state for
KVM_SET_LAPIC, i.e. make the x2APIC fully readonly in KVM. Commit
a92e2543d6 ("KVM: x86: use hardware-compatible format for APIC ID
register"), which added the fixup, didn't intend to allow userspace to
modify the x2APIC ID. In fact, that commit is when KVM first started
treating the x2APIC ID as readonly, apparently to fix some race:
static inline u32 kvm_apic_id(struct kvm_lapic *apic)
{
- return (kvm_lapic_get_reg(apic, APIC_ID) >> 24) & 0xff;
+ /* To avoid a race between apic_base and following APIC_ID update when
+ * switching to x2apic_mode, the x2apic mode returns initial x2apic id.
+ */
+ if (apic_x2apic_mode(apic))
+ return apic->vcpu->vcpu_id;
+
+ return kvm_lapic_get_reg(apic, APIC_ID) >> 24;
}
Furthermore, KVM doesn't support delivering interrupts to vCPUs with a
modified x2APIC ID, but KVM *does* return the modified value on a guest
RDMSR and for KVM_GET_LAPIC. I.e. no remotely sane setup can actually
work with a modified x2APIC ID.
Making the x2APIC ID fully readonly fixes a WARN in KVM's optimized map
calculation, which expects the LDR to align with the x2APIC ID.
WARNING: CPU: 2 PID: 958 at arch/x86/kvm/lapic.c:331 kvm_recalculate_apic_map+0x609/0xa00 [kvm]
CPU: 2 PID: 958 Comm: recalc_apic_map Not tainted 6.4.0-rc3-vanilla+ #35
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Arch Linux 1.16.2-1-1 04/01/2014
RIP: 0010:kvm_recalculate_apic_map+0x609/0xa00 [kvm]
Call Trace:
<TASK>
kvm_apic_set_state+0x1cf/0x5b0 [kvm]
kvm_arch_vcpu_ioctl+0x1806/0x2100 [kvm]
kvm_vcpu_ioctl+0x663/0x8a0 [kvm]
__x64_sys_ioctl+0xb8/0xf0
do_syscall_64+0x56/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
RIP: 0033:0x7fade8b9dd6f
Unfortunately, the WARN can still trigger for other CPUs than the current
one by racing against KVM_SET_LAPIC, so remove it completely.
Reported-by: Michal Luczaj <mhal@rbox.co>
Closes: https://lore.kernel.org/all/814baa0c-1eaa-4503-129f-059917365e80@rbox.co
Reported-by: Haoyu Wu <haoyuwu254@gmail.com>
Closes: https://lore.kernel.org/all/20240126161633.62529-1-haoyuwu254@gmail.com
Reported-by: syzbot+545f1326f405db4e1c3e@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/000000000000c2a6b9061cbca3c3@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-ID: <20240802202941.344889-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: James Houghton <jthoughton@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b06f388994 upstream.
lockdep detects the following circular locking dependency:
CPU 0 CPU 1
========================== ============================
cdns_uart_isr() printk()
uart_port_lock(port) console_lock()
cdns_uart_console_write()
if (!port->sysrq)
uart_port_lock(port)
uart_handle_break()
port->sysrq = ...
uart_handle_sysrq_char()
printk()
console_lock()
The fixed commit attempts to avoid this situation by only taking the
port lock in cdns_uart_console_write if port->sysrq unset. However, if
(as shown above) cdns_uart_console_write runs before port->sysrq is set,
then it will try to take the port lock anyway. This may result in a
deadlock.
Fix this by splitting sysrq handling into two parts. We use the prepare
helper under the port lock and defer handling until we release the lock.
Fixes: 74ea66d4ca ("tty: xuartps: Improve sysrq handling")
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Cc: stable@vger.kernel.org # c980248179: serial: xilinx_uartps: Use port lock wrappers
Acked-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20250110213822.2107462-1-sean.anderson@linux.dev
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc31744a29 upstream.
When ident_pud_init() uses only GB pages to create identity maps, large
ranges of addresses not actually requested can be included in the resulting
table; a 4K request will map a full GB. This can include a lot of extra
address space past that requested, including areas marked reserved by the
BIOS. That allows processor speculation into reserved regions, that on UV
systems can cause system halts.
Only use GB pages when map creation requests include the full GB page of
space. Fall back to using smaller 2M pages when only portions of a GB page
are included in the request.
No attempt is made to coalesce mapping requests. If a request requires a
map entry at the 2M (pmd) level, subsequent mapping requests within the
same 1G region will also be at the pmd level, even if adjacent or
overlapping such requests could have been combined to map a full GB page.
Existing usage starts with larger regions and then adds smaller regions, so
this should not have any great consequence.
Signed-off-by: Steve Wahl <steve.wahl@hpe.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Pavin Joseph <me@pavinjoseph.com>
Tested-by: Sarah Brofeldt <srhb@dbc.dk>
Tested-by: Eric Hagberg <ehagberg@gmail.com>
Link: https://lore.kernel.org/all/20240717213121.3064030-3-steve.wahl@hpe.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Fixes commit is a backport renaming a variable, from AF_INET6 to
MPTCP_LIB_AF_INET6.
The commit has been applied without conflicts, except that it missed one
extra variable that was in v6.6, but not in the version linked to the
Fixes commit.
This variable has then been renamed too to avoid these errors:
LISTENER_CREATED 10.0.2.1:10100 ./mptcp_join.sh: line 2944: [: 2: unary operator expected
LISTENER_CLOSED 10.0.2.1:10100 ./mptcp_join.sh: line 2944: [: 2: unary operator expected
Fixes: a17d141912 ("selftests: mptcp: declare event macros in mptcp_lib")
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 31ad74b202 upstream.
At present, the object->file has the NULL pointer dereference problem in
ondemand-mode. The root cause is that the allocated fd and object->file
lifetime are inconsistent, and the user-space invocation to anon_fd uses
object->file. Following is the process that triggers the issue:
[write fd] [umount]
cachefiles_ondemand_fd_write_iter
fscache_cookie_state_machine
cachefiles_withdraw_cookie
if (!file) return -ENOBUFS
cachefiles_clean_up_object
cachefiles_unmark_inode_in_use
fput(object->file)
object->file = NULL
// file NULL pointer dereference!
__cachefiles_write(..., file, ...)
Fix this issue by add an additional reference count to the object->file
before write/llseek, and decrement after it finished.
Fixes: c838305450 ("cachefiles: notify the user daemon when looking up cookie")
Signed-off-by: Zizhi Wo <wozizhi@huawei.com>
Link: https://lore.kernel.org/r/20241107110649.3980193-5-wozizhi@huawei.com
Reviewed-by: David Howells <dhowells@redhat.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Bin Lan <lanbincn@qq.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c8507c63f upstream.
This commit re-attempts the backport of the change to the linux-6.6.y
branch. Commit 6e1a822593 ("btrfs: avoid monopolizing a core when
activating a swap file") on this branch was reverted.
During swap activation we iterate over the extents of a file and we can
have many thousands of them, so we can end up in a busy loop monopolizing
a core. Avoid this by doing a voluntary reschedule after processing each
extent.
CC: stable@vger.kernel.org # 5.4+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 6e1a822593.
The backport for linux-6.6.y, commit 6e1a822593 ("btrfs: avoid
monopolizing a core when activating a swap file"), inserted
cond_resched() in the wrong location.
Revert it now; a subsequent commit will re-backport the original patch.
Fixes: 6e1a822593 ("btrfs: avoid monopolizing a core when activating a swap file") # linux-6.6.y
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05d91cdb1f upstream.
Copy of the rationale from 790071347a:
Change ndo_set_mac_address to dev_set_mac_address because
dev_set_mac_address provides a way to notify network layer about MAC
change. In other case, services may not aware about MAC change and keep
using old one which set from network adapter driver.
As example, DHCP client from systemd do not update MAC address without
notification from net subsystem which leads to the problem with acquiring
the right address from DHCP server.
Since dev_set_mac_address requires RTNL lock the operation can not be
performed directly in the response handler, see
9e2bbab94b.
The way of selecting the first suitable MAC address from the list is
changed, instead of having the driver check it this patch just assumes
any valid MAC should be good.
Fixes: b8291cf3d1 ("net/ncsi: Add NC-SI 1.2 Get MC MAC Address command")
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit be92ab2de0 upstream.
The QSPI peripheral control and status registers are
accessible via the SoC's APB bus, whereas MMIO transactions'
data travels on the AHB bus.
Microchip documentation and even sample code from Atmel
emphasises the need for a memory barrier before the first
MMIO transaction to the AHB-connected QSPI, and before the
last write to its registers via APB. This is achieved by
the following lines in `atmel_qspi_transfer()`:
/* Dummy read of QSPI_IFR to synchronize APB and AHB accesses */
(void)atmel_qspi_read(aq, QSPI_IFR);
However, the current documentation makes no mention to
synchronization requirements in the other direction, i.e.
after the last data written via AHB, and before the first
register access on APB.
In our case, we were facing an issue where the QSPI peripheral
would cease to send any new CSR (nCS Rise) interrupts,
leading to a timeout in `atmel_qspi_wait_for_completion()`
and ultimately this panic in higher levels:
ubi0 error: ubi_io_write: error -110 while writing 63108 bytes
to PEB 491:128, written 63104 bytes
After months of extensive research of the codebase, fiddling
around the debugger with kgdb, and back-and-forth with
Microchip, we came to the conclusion that the issue is
probably that the peripheral is still busy receiving on AHB
when the LASTXFER bit is written to its Control Register
on APB, therefore this write gets lost, and the peripheral
still thinks there is more data to come in the MMIO transfer.
This was first formulated when we noticed that doubling the
write() of QSPI_CR_LASTXFER seemed to solve the problem.
Ultimately, the solution is to introduce memory barriers
after the AHB-mapped MMIO transfers, to ensure ordering.
Fixes: d5433def31 ("mtd: spi-nor: atmel-quadspi: Add spi-mem support to atmel-quadspi")
Cc: Hari.PrasathGE@microchip.com
Cc: Mahesh.Abotula@microchip.com
Cc: Marco.Cardellini@microchip.com
Cc: stable@vger.kernel.org # c0a0203cf5: ("spi: atmel-quadspi: Create `atmel_qspi_ops`"...)
Cc: stable@vger.kernel.org # 6.x.y
Signed-off-by: Bence Csókás <csokas.bence@prolan.hu>
Link: https://patch.msgid.link/20241219091258.395187-1-csokas.bence@prolan.hu
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ddd068d814 upstream.
Declare ftrace_get_parent_ra_addr() as static to suppress clang
compiler warning that 'no previous prototype'. This function is
not intended to be called from other parts.
Fix follow error with clang-19:
arch/mips/kernel/ftrace.c:251:15: error: no previous prototype for function 'ftrace_get_parent_ra_addr' [-Werror,-Wmissing-prototypes]
251 | unsigned long ftrace_get_parent_ra_addr(unsigned long self_ra, unsigned long
| ^
arch/mips/kernel/ftrace.c:251:1: note: declare 'static' if the function is not intended to be used outside of this translation unit
251 | unsigned long ftrace_get_parent_ra_addr(unsigned long self_ra, unsigned long
| ^
| static
1 error generated.
Signed-off-by: WangYuli <wangyuli@uniontech.com>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 459915f555 upstream.
Commit 50ebd19e35 ("pinctrl: samsung: drop pin banks references on
error paths") fixed the pin bank references on the error paths of the
probe function, but there is still an error path where this is not done.
If samsung_pinctrl_get_soc_data() does not fail, the child references
will have acquired, and they will need to be released in the error path
of platform_get_irq_optional(), as it is done in the following error
paths within the probe function.
Replace the direct return in the error path with a goto instruction to
the cleanup function.
Cc: stable@vger.kernel.org
Fixes: a382d568f1 ("pinctrl: samsung: Use platform_get_irq_optional() to get the interrupt")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://lore.kernel.org/r/20241106-samsung-pinctrl-put-v1-1-de854e26dd03@gmail.com
[krzysztof: change Fixes SHA to point to commit introducing the return
leading to OF node leak]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a4dfce7559 upstream.
Currently, when either SIGINT from the user or SIGALRM from the duration
timer is caught by rtla-timerlat, stop_tracing is set to break out of
the main loop. This is not sufficient for cases where the timerlat
tracer is producing more data than rtla can consume, since in that case,
rtla is looping indefinitely inside tracefs_iterate_raw_events, never
reaches the check of stop_tracing and hangs.
In addition to setting stop_tracing, also stop the timerlat tracer on
received signal (SIGINT or SIGALRM). This will stop new samples so that
the existing samples may be processed and tracefs_iterate_raw_events
eventually exits.
Cc: stable@vger.kernel.org
Cc: John Kacur <jkacur@redhat.com>
Cc: Luis Goncalves <lgoncalv@redhat.com>
Cc: Gabriele Monaco <gmonaco@redhat.com>
Link: https://lore.kernel.org/20250116144931.649593-4-tglozar@redhat.com
Fixes: a828cd18bc ("rtla: Add timerlat tool and timelart top mode")
Signed-off-by: Tomas Glozar <tglozar@redhat.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c73cab9dbe upstream.
Currently, when either SIGINT from the user or SIGALRM from the duration
timer is caught by rtla-timerlat, stop_tracing is set to break out of
the main loop. This is not sufficient for cases where the timerlat
tracer is producing more data than rtla can consume, since in that case,
rtla is looping indefinitely inside tracefs_iterate_raw_events, never
reaches the check of stop_tracing and hangs.
In addition to setting stop_tracing, also stop the timerlat tracer on
received signal (SIGINT or SIGALRM). This will stop new samples so that
the existing samples may be processed and tracefs_iterate_raw_events
eventually exits.
Cc: stable@vger.kernel.org
Cc: John Kacur <jkacur@redhat.com>
Cc: Luis Goncalves <lgoncalv@redhat.com>
Cc: Gabriele Monaco <gmonaco@redhat.com>
Link: https://lore.kernel.org/20250116144931.649593-3-tglozar@redhat.com
Fixes: 1eeb6328e8 ("rtla/timerlat: Add timerlat hist mode")
Signed-off-by: Tomas Glozar <tglozar@redhat.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 217f0b1e99 upstream.
When using rtla timerlat with userspace threads (-u or -U), rtla
disables the OSNOISE_WORKLOAD option in
/sys/kernel/tracing/osnoise/options. This option is not re-enabled in a
subsequent run with kernel-space threads, leading to rtla collecting no
results if the previous run exited abnormally:
$ rtla timerlat top -u
^\Quit (core dumped)
$ rtla timerlat top -k -d 1s
Timer Latency
0 00:00:01 | IRQ Timer Latency (us) | Thread Timer Latency (us)
CPU COUNT | cur min avg max | cur min avg max
The issue persists until OSNOISE_WORKLOAD is set manually by running:
$ echo OSNOISE_WORKLOAD > /sys/kernel/tracing/osnoise/options
Set OSNOISE_WORKLOAD when running rtla with kernel-space threads if
available to fix the issue.
Cc: stable@vger.kernel.org
Cc: John Kacur <jkacur@redhat.com>
Cc: Luis Goncalves <lgoncalv@redhat.com>
Link: https://lore.kernel.org/20250107144823.239782-4-tglozar@redhat.com
Fixes: cdca4f4e5e ("rtla/timerlat_top: Add timerlat user-space support")
Signed-off-by: Tomas Glozar <tglozar@redhat.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d8d866171a upstream.
When using rtla timerlat with userspace threads (-u or -U), rtla
disables the OSNOISE_WORKLOAD option in
/sys/kernel/tracing/osnoise/options. This option is not re-enabled in a
subsequent run with kernel-space threads, leading to rtla collecting no
results if the previous run exited abnormally:
$ rtla timerlat hist -u
^\Quit (core dumped)
$ rtla timerlat hist -k -d 1s
Index
over:
count:
min:
avg:
max:
ALL: IRQ Thr Usr
count: 0 0 0
min: - - -
avg: - - -
max: - - -
The issue persists until OSNOISE_WORKLOAD is set manually by running:
$ echo OSNOISE_WORKLOAD > /sys/kernel/tracing/osnoise/options
Set OSNOISE_WORKLOAD when running rtla with kernel-space threads if
available to fix the issue.
Cc: stable@vger.kernel.org
Cc: John Kacur <jkacur@redhat.com>
Cc: Luis Goncalves <lgoncalv@redhat.com>
Link: https://lore.kernel.org/20250107144823.239782-3-tglozar@redhat.com
Fixes: ed774f7481 ("rtla/timerlat_hist: Add timerlat user-space support")
Signed-off-by: Tomas Glozar <tglozar@redhat.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e3ff424592 upstream.
If a timerlat tracer is started with the osnoise option OSNOISE_WORKLOAD
disabled, but then that option is enabled and timerlat is removed, the
tracepoints that were enabled on timerlat registration do not get
disabled. If the option is disabled again and timelat is started, then it
triggers a warning in the tracepoint code due to registering the
tracepoint again without ever disabling it.
Do not use the same user space defined options to know to disable the
tracepoints when timerlat is removed. Instead, set a global flag when it
is enabled and use that flag to know to disable the events.
~# echo NO_OSNOISE_WORKLOAD > /sys/kernel/tracing/osnoise/options
~# echo timerlat > /sys/kernel/tracing/current_tracer
~# echo OSNOISE_WORKLOAD > /sys/kernel/tracing/osnoise/options
~# echo nop > /sys/kernel/tracing/current_tracer
~# echo NO_OSNOISE_WORKLOAD > /sys/kernel/tracing/osnoise/options
~# echo timerlat > /sys/kernel/tracing/current_tracer
Triggers:
------------[ cut here ]------------
WARNING: CPU: 6 PID: 1337 at kernel/tracepoint.c:294 tracepoint_add_func+0x3b6/0x3f0
Modules linked in:
CPU: 6 UID: 0 PID: 1337 Comm: rtla Not tainted 6.13.0-rc4-test-00018-ga867c441128e-dirty #73
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
RIP: 0010:tracepoint_add_func+0x3b6/0x3f0
Code: 48 8b 53 28 48 8b 73 20 4c 89 04 24 e8 23 59 11 00 4c 8b 04 24 e9 36 fe ff ff 0f 0b b8 ea ff ff ff 45 84 e4 0f 84 68 fe ff ff <0f> 0b e9 61 fe ff ff 48 8b 7b 18 48 85 ff 0f 84 4f ff ff ff 49 8b
RSP: 0018:ffffb9b003a87ca0 EFLAGS: 00010202
RAX: 00000000ffffffef RBX: ffffffff92f30860 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffff9bf59e91ccd0 RDI: ffffffff913b6410
RBP: 000000000000000a R08: 00000000000005c7 R09: 0000000000000002
R10: ffffb9b003a87ce0 R11: 0000000000000002 R12: 0000000000000001
R13: ffffb9b003a87ce0 R14: ffffffffffffffef R15: 0000000000000008
FS: 00007fce81209240(0000) GS:ffff9bf6fdd00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000055e99b728000 CR3: 00000001277c0002 CR4: 0000000000172ef0
Call Trace:
<TASK>
? __warn.cold+0xb7/0x14d
? tracepoint_add_func+0x3b6/0x3f0
? report_bug+0xea/0x170
? handle_bug+0x58/0x90
? exc_invalid_op+0x17/0x70
? asm_exc_invalid_op+0x1a/0x20
? __pfx_trace_sched_migrate_callback+0x10/0x10
? tracepoint_add_func+0x3b6/0x3f0
? __pfx_trace_sched_migrate_callback+0x10/0x10
? __pfx_trace_sched_migrate_callback+0x10/0x10
tracepoint_probe_register+0x78/0xb0
? __pfx_trace_sched_migrate_callback+0x10/0x10
osnoise_workload_start+0x2b5/0x370
timerlat_tracer_init+0x76/0x1b0
tracing_set_tracer+0x244/0x400
tracing_set_trace_write+0xa0/0xe0
vfs_write+0xfc/0x570
? do_sys_openat2+0x9c/0xe0
ksys_write+0x72/0xf0
do_syscall_64+0x79/0x1c0
entry_SYSCALL_64_after_hwframe+0x76/0x7e
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Tomas Glozar <tglozar@redhat.com>
Cc: Gabriele Monaco <gmonaco@redhat.com>
Cc: Luis Goncalves <lgoncalv@redhat.com>
Cc: John Kacur <jkacur@redhat.com>
Link: https://lore.kernel.org/20250123204159.4450c88e@gandalf.local.home
Fixes: e88ed227f6 ("tracing/timerlat: Add user-space interface")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6bb194d036 upstream.
The NCSI state machine as it's currently implemented assumes that
transition to the next logical state is performed either explicitly by
calling `schedule_work(&ndp->work)` to re-queue itself or implicitly
after processing the predefined (ndp->pending_req_num) number of
replies. Thus to avoid the configuration FSM from advancing prematurely
and getting out of sync with the process it's essential to not skip
waiting for a reply.
This patch makes the code wait for reception of the Deselect Package
response for the last package probed before proceeding to channel
configuration.
Thanks go to Potin Lai and Cosmo Chou for the initial investigation and
testing.
Fixes: 8e13f70be0 ("net/ncsi: Probe single packages to avoid conflict")
Cc: stable@vger.kernel.org
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Link: https://patch.msgid.link/20250116152900.8656-1-fercerpav@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
