Pass the DRM connector name to any configured backlight
device so that userspace can associate the two items.
Ideally this should be in drm_panel, but it is bridge/panel
that creates the drm_connector and therefore knows the name.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The naming of backlight devices is not terribly useful for
associating a backlight controller with a display (assuming
it is attached to one).
Add a sysfs node that will return a display name that can be set
by other subsystems.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The camera sync parameter declarations include are invalid in that they
have both embedded string values and following cell values. The
intention here was to use the cell values, but the embedded "0" was
not removed as it should have been.
The implication of this mistake is that inverted sync flags would be
ignored because the 0 value corresponds to GPIO_ACTIVE_HIGH. The
extra cell value would be treated as the start of another override,
but then ignored because the end of the parameter is reached.
These errors should have been picked up by the automated checks, but
the base dts files weren't subjected to the same validation. This has
now been corrected.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
If a set of read requests are issued by an endpoint, they are streamed
into a resynchronisation FIFO prior to exiting the RC. This FIFO has an
edge case where it can drop QoS for a request to 0 if there's a single
outstanding read request in the FIFO, and another is pushed when the
FIFO is popped. Requests with a QoS of 0 can take hundreds of
microseconds to complete.
By adding an experimentally-determined amount of backpressure on the pop
side, the critical level transition can largely be avoided.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
The stride value reported for output image buffers should be at least
as large as any value that was passed in by the caller (subject to
correct alignment for the pixel format). If the value is zero (meaning
no value was passed), or is too small, the minimum acceptable value
will be substituted.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Interop testing with the M.2 HAT has revealed that there are many quirky
endpoint devices out there, so users should have a way of rapidly
iterating to find which quirk is causing reliability issues.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
L1 sub-states require the connection of the CLKREQ# auxiliary signal
which is a PCB-level decision, and also depends on the vagrancies of
adapters/interposers/slots that may exist between the chip and the
endpoint.
If this parameter is present, and the RC driver sees an L1 substate
capability in the endpoint, then the result is a broken link if CLKREQ#
isn't end-to-end connected - regardless of the state of the L1.x enable
bits in the RC.
Board-specific methods (HAT+ overlay, board DTB) should define this
property if required.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
There are no MEDIA_BUS_FMT_* defines for GRB or BRG, and adding
them is a pain.
Add a DT override to allow setting the order.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
As with many microcontrollers, the panel wants to use clock
stretching during a read so that the appropriate return value
can be generated and programmed into the hardware.
With Pi0-3 really not supporting clock stretching, this resulted
in the panel firmware dying.
Insert a delay between the write and the read to give the firmware
a chance to generate the relevant return value.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
commit 6cf3506587 upstream.
If kobject_add() is fail in bind_rdev_to_array(), 'rdev->serial' will be
alloc not be freed, and kmemleak occurs.
unreferenced object 0xffff88815a350000 (size 49152):
comm "mdadm", pid 789, jiffies 4294716910
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace (crc f773277a):
[<0000000058b0a453>] kmemleak_alloc+0x61/0xe0
[<00000000366adf14>] __kmalloc_large_node+0x15e/0x270
[<000000002e82961b>] __kmalloc_node.cold+0x11/0x7f
[<00000000f206d60a>] kvmalloc_node+0x74/0x150
[<0000000034bf3363>] rdev_init_serial+0x67/0x170
[<0000000010e08fe9>] mddev_create_serial_pool+0x62/0x220
[<00000000c3837bf0>] bind_rdev_to_array+0x2af/0x630
[<0000000073c28560>] md_add_new_disk+0x400/0x9f0
[<00000000770e30ff>] md_ioctl+0x15bf/0x1c10
[<000000006cfab718>] blkdev_ioctl+0x191/0x3f0
[<0000000085086a11>] vfs_ioctl+0x22/0x60
[<0000000018b656fe>] __x64_sys_ioctl+0xba/0xe0
[<00000000e54e675e>] do_syscall_64+0x71/0x150
[<000000008b0ad622>] entry_SYSCALL_64_after_hwframe+0x6c/0x74
Fixes: 963c555e75 ("md: introduce mddev_create/destroy_wb_pool for the change of member device")
Signed-off-by: Li Nan <linan122@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20240208085556.2412922-1-linan666@huaweicloud.com
[ mddev_destroy_serial_pool third parameter was removed in mainline,
where there is no need to suspend within this function anymore. ]
Signed-off-by: Jeremy Bongio <jbongio@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1db7959aac upstream.
[BUG]
There is a recent report that when memory pressure is high (including
cached pages), btrfs can spend most of its time on memory allocation in
btrfs_alloc_page_array() for compressed read/write.
[CAUSE]
For btrfs_alloc_page_array() we always go alloc_pages_bulk_array(), and
even if the bulk allocation failed (fell back to single page
allocation) we still retry but with extra memalloc_retry_wait().
If the bulk alloc only returned one page a time, we would spend a lot of
time on the retry wait.
The behavior was introduced in commit 395cb57e85 ("btrfs: wait between
incomplete batch memory allocations").
[FIX]
Although the commit mentioned that other filesystems do the wait, it's
not the case at least nowadays.
All the mainlined filesystems only call memalloc_retry_wait() if they
failed to allocate any page (not only for bulk allocation).
If there is any progress, they won't call memalloc_retry_wait() at all.
For example, xfs_buf_alloc_pages() would only call memalloc_retry_wait()
if there is no allocation progress at all, and the call is not for
metadata readahead.
So I don't believe we should call memalloc_retry_wait() unconditionally
for short allocation.
Call memalloc_retry_wait() if it fails to allocate any page for tree
block allocation (which goes with __GFP_NOFAIL and may not need the
special handling anyway), and reduce the latency for
btrfs_alloc_page_array().
Reported-by: Julian Taylor <julian.taylor@1und1.de>
Tested-by: Julian Taylor <julian.taylor@1und1.de>
Link: https://lore.kernel.org/all/8966c095-cbe7-4d22-9784-a647d1bf27c3@1und1.de/
Fixes: 395cb57e85 ("btrfs: wait between incomplete batch memory allocations")
CC: stable@vger.kernel.org # 6.1+
Reviewed-by: Sweet Tea Dorminy <sweettea-kernel@dorminy.me>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6827738dc6 upstream.
After the patch to restrict the use of mmap() to CAP_SYS_RAWIO for
the currently existing devices, most applications can no longer make
use of the accelerators as in production "you don't run things as root".
To keep the DSA and IAA accelerators usable, hook up a write() method
so that applications can still submit work. In the write method,
sufficient input validation is performed to avoid the security issue
that required the mmap CAP_SYS_RAWIO check.
One complication is that the DSA device allows for indirect ("batched")
descriptors. There is no reasonable way to do the input validation
on these indirect descriptors so the write() method will not allow these
to be submitted to the hardware on affected hardware, and the sysfs
enumeration of support for the opcode is also removed.
Early performance data shows that the performance delta for most common
cases is within the noise.
Signed-off-by: Nikhil Rao <nikhil.rao@intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e11452eb07 upstream.
On Sapphire Rapids and related platforms, the DSA and IAA devices have an
erratum that causes direct access (for example, by using the ENQCMD or
MOVDIR64 instructions) from untrusted applications to be a security problem.
To solve this, add a flag to the PCI device enumeration and device structures
to indicate the presence/absence of this security exposure. In the mmap()
method of the device, this flag is then used to enforce that the user
has the CAP_SYS_RAWIO capability.
In a future patch, a write() based method will be added that allows untrusted
applications submit work to the accelerator, where the kernel can do
sanity checking on the user input to ensure secure operation of the accelerator.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 95feb3160e upstream.
Due to an erratum with the SPR_DSA and SPR_IAX devices, it is not secure to assign
these devices to virtual machines. Add the PCI IDs of these devices to the VFIO
denylist to ensure that this is handled appropriately by the VFIO subsystem.
The SPR_DSA and SPR_IAX devices are on-SOC devices for the Sapphire Rapids
(and related) family of products that perform data movement and compression.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40d442f969 upstream.
A recent commit fixed the code that parses the firmware files before
downloading them to the controller but introduced a memory leak in case
the sanity checks ever fail.
Make sure to free the firmware buffer before returning on errors.
Fixes: f905ae0be4b7 ("Bluetooth: qca: add missing firmware sanity checks")
Cc: stable@vger.kernel.org # 4.19
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cda0d6a198 upstream.
Add the missing sanity checks and move the 255-byte build-id buffer off
the stack to avoid leaking stack data through debugfs in case the
build-info reply is malformed.
Fixes: c0187b0bd3 ("Bluetooth: btqca: Add support to read FW build version for WCN3991 BTSoC")
Cc: stable@vger.kernel.org # 5.12
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd336649ba upstream.
The default device address apparently comes from the NVM configuration
file and can differ quite a bit between controllers.
Store the default address when parsing the configuration file and use it
to determine whether the controller has been provisioned with an
address.
This makes sure that devices without a unique address start as
unconfigured unless a valid address has been provided in the devicetree.
Fixes: 32868e126c ("Bluetooth: qca: fix invalid device address check")
Cc: stable@vger.kernel.org # 6.5
Cc: Doug Anderson <dianders@chromium.org>
Cc: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a112d3c72a upstream.
The NVM configuration files used by WCN3988 and WCN3990/1/8 have two
sets of configuration tags that are enclosed by a type-length header of
type four which the current parser fails to account for.
Instead the driver happily parses random data as if it were valid tags,
something which can lead to the configuration data being corrupted if it
ever encounters the words 0x0011 or 0x001b.
As is clear from commit b63882549b ("Bluetooth: btqca: Fix the NVM
baudrate tag offcet for wcn3991") the intention has always been to
process the configuration data also for WCN3991 and WCN3998 which
encodes the baud rate at a different offset.
Fix the parser so that it can handle the WCN3xxx configuration files,
which has an enclosing type-length header of type four and two sets of
TLV tags enclosed by a type-length header of type two and three,
respectively.
Note that only the first set, which contains the tags the driver is
currently looking for, will be parsed for now.
With the parser fixed, the software in-band sleep bit will now be set
for WCN3991 and WCN3998 (as it is for later controllers) and the default
baud rate 3200000 may be updated by the driver also for WCN3xxx
controllers.
Notably the deep-sleep feature bit is already set by default in all
configuration files in linux-firmware.
Fixes: 4219d46868 ("Bluetooth: btqca: Add wcn3990 firmware download support.")
Cc: stable@vger.kernel.org # 4.19
Cc: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e4edfa1e2 upstream.
Add the missing sanity checks when parsing the firmware files before
downloading them to avoid accessing and corrupting memory beyond the
vmalloced buffer.
Fixes: 83e81961ff ("Bluetooth: btqca: Introduce generic QCA ROME support")
Cc: stable@vger.kernel.org # 4.10
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66c39332d0 upstream.
Qualcomm Bluetooth controllers may not have been provisioned with a
valid device address and instead end up using the default address
00:00:00:00:5a:ad.
This address is now used to determine if a controller has a valid
address or if one needs to be provided through devicetree or by user
space before the controller can be used.
It turns out that the WCN3991 controllers used in Chromium Trogdor
machines use a different default address, 39:98:00:00:5a:ad, which also
needs to be marked as invalid so that the correct address is fetched
from the devicetree.
Qualcomm has unfortunately not yet provided any answers as to whether
the 39:98 encodes a hardware id and if there are other variants of the
default address that needs to be handled by the driver.
For now, add the Trogdor WCN3991 default address to the device address
check to avoid having these controllers start with the default address
instead of their assigned addresses.
Fixes: 32868e126c ("Bluetooth: qca: fix invalid device address check")
Cc: stable@vger.kernel.org # 6.5
Cc: Doug Anderson <dianders@chromium.org>
Cc: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 32868e126c upstream.
Qualcomm Bluetooth controllers may not have been provisioned with a
valid device address and instead end up using the default address
00:00:00:00:5a:ad.
This was previously believed to be due to lack of persistent storage for
the address but it may also be due to integrators opting to not use the
on-chip OTP memory and instead store the address elsewhere (e.g. in
storage managed by secure world firmware).
According to Qualcomm, at least WCN6750, WCN6855 and WCN7850 have
on-chip OTP storage for the address.
As the device type alone cannot be used to determine when the address is
valid, instead read back the address during setup() and only set the
HCI_QUIRK_USE_BDADDR_PROPERTY flag when needed.
This specifically makes sure that controllers that have been provisioned
with an address do not start as unconfigured.
Reported-by: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Link: https://lore.kernel.org/r/124a7d54-5a18-4be7-9a76-a12017f6cce5@quicinc.com/
Fixes: 5971752de4 ("Bluetooth: hci_qca: Set HCI_QUIRK_USE_BDADDR_PROPERTY for wcn3990")
Fixes: e668eb1e15 ("Bluetooth: hci_core: Don't stop BT if the BD address missing in dts")
Fixes: 6945795bc8 ("Bluetooth: fix use-bdaddr-property quirk")
Cc: stable@vger.kernel.org # 6.5
Cc: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reported-by: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 22e61e15af upstream.
Treat the events directory the same as other directories when it comes to
permissions. The events directory was considered different because it's
dentry is persistent, whereas the other directory dentries are created
when accessed. But the way tracefs now does its ownership by using the
root dentry's permissions as the default permissions, the events directory
can get out of sync when a remount is performed setting the group and user
permissions.
Remove the special case for the events directory on setting the
attributes. This allows the updates caused by remount to work properly as
well as simplifies the code.
Link: https://lore.kernel.org/linux-trace-kernel/20240502200906.002923579@goodmis.org
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Fixes: 8186fff7ab ("tracefs/eventfs: Use root and instance inodes as default ownership")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6599bd5517 upstream.
If the instances directory's permissions were never change, then have it
and its children use the mount point permissions as the default.
Currently, the permissions of instance directories are determined by the
instance directory's permissions itself. But if the tracefs file system is
remounted and changes the permissions, the instance directory and its
children should use the new permission.
But because both the instance directory and its children use the instance
directory's inode for permissions, it misses the update.
To demonstrate this:
# cd /sys/kernel/tracing/
# mkdir instances/foo
# ls -ld instances/foo
drwxr-x--- 5 root root 0 May 1 19:07 instances/foo
# ls -ld instances
drwxr-x--- 3 root root 0 May 1 18:57 instances
# ls -ld current_tracer
-rw-r----- 1 root root 0 May 1 18:57 current_tracer
# mount -o remount,gid=1002 .
# ls -ld instances
drwxr-x--- 3 root root 0 May 1 18:57 instances
# ls -ld instances/foo/
drwxr-x--- 5 root root 0 May 1 19:07 instances/foo/
# ls -ld current_tracer
-rw-r----- 1 root lkp 0 May 1 18:57 current_tracer
Notice that changing the group id to that of "lkp" did not affect the
instances directory nor its children. It should have been:
# ls -ld current_tracer
-rw-r----- 1 root root 0 May 1 19:19 current_tracer
# ls -ld instances/foo/
drwxr-x--- 5 root root 0 May 1 19:25 instances/foo/
# ls -ld instances
drwxr-x--- 3 root root 0 May 1 19:19 instances
# mount -o remount,gid=1002 .
# ls -ld current_tracer
-rw-r----- 1 root lkp 0 May 1 19:19 current_tracer
# ls -ld instances
drwxr-x--- 3 root lkp 0 May 1 19:19 instances
# ls -ld instances/foo/
drwxr-x--- 5 root lkp 0 May 1 19:25 instances/foo/
Where all files were updated by the remount gid update.
Link: https://lore.kernel.org/linux-trace-kernel/20240502200905.686838327@goodmis.org
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Fixes: 8186fff7ab ("tracefs/eventfs: Use root and instance inodes as default ownership")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit baa23a8d43 upstream.
There's an inconsistency with the way permissions are handled in tracefs.
Because the permissions are generated when accessed, they default to the
root inode's permission if they were never set by the user. If the user
sets the permissions, then a flag is set and the permissions are saved via
the inode (for tracefs files) or an internal attribute field (for
eventfs).
But if a remount happens that specify the permissions, all the files that
were not changed by the user gets updated, but the ones that were are not.
If the user were to remount the file system with a given permission, then
all files and directories within that file system should be updated.
This can cause security issues if a file's permission was updated but the
admin forgot about it. They could incorrectly think that remounting with
permissions set would update all files, but miss some.
For example:
# cd /sys/kernel/tracing
# chgrp 1002 current_tracer
# ls -l
[..]
-rw-r----- 1 root root 0 May 1 21:25 buffer_size_kb
-rw-r----- 1 root root 0 May 1 21:25 buffer_subbuf_size_kb
-r--r----- 1 root root 0 May 1 21:25 buffer_total_size_kb
-rw-r----- 1 root lkp 0 May 1 21:25 current_tracer
-rw-r----- 1 root root 0 May 1 21:25 dynamic_events
-r--r----- 1 root root 0 May 1 21:25 dyn_ftrace_total_info
-r--r----- 1 root root 0 May 1 21:25 enabled_functions
Where current_tracer now has group "lkp".
# mount -o remount,gid=1001 .
# ls -l
-rw-r----- 1 root tracing 0 May 1 21:25 buffer_size_kb
-rw-r----- 1 root tracing 0 May 1 21:25 buffer_subbuf_size_kb
-r--r----- 1 root tracing 0 May 1 21:25 buffer_total_size_kb
-rw-r----- 1 root lkp 0 May 1 21:25 current_tracer
-rw-r----- 1 root tracing 0 May 1 21:25 dynamic_events
-r--r----- 1 root tracing 0 May 1 21:25 dyn_ftrace_total_info
-r--r----- 1 root tracing 0 May 1 21:25 enabled_functions
Everything changed but the "current_tracer".
Add a new link list that keeps track of all the tracefs_inodes which has
the permission flags that tell if the file/dir should use the root inode's
permission or not. Then on remount, clear all the flags so that the
default behavior of using the root inode's permission is done for all
files and directories.
Link: https://lore.kernel.org/linux-trace-kernel/20240502200905.529542160@goodmis.org
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Fixes: 8186fff7ab ("tracefs/eventfs: Use root and instance inodes as default ownership")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 691aae4f36 upstream.
This patch fix xfstests generic/070 test with smb2 leases = yes.
cifs.ko doesn't set parent lease key and epoch in create context v2 lease.
ksmbd suppose that parent lease and epoch are vaild if data length is
v2 lease context size and handle directory lease using this values.
ksmbd should hanle it as v1 lease not v2 lease if parent lease key and
epoch are not set in create context v2 lease.
Cc: stable@vger.kernel.org
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 97c2ec6466 upstream.
This patch fixes generic/011 when enable smb2 leases.
if ksmbd sends multiple notifications for a file, cifs increments
the reference count of the file but it does not decrement the count by
the failure of queue_work.
So even if the file is closed, cifs does not send a SMB2_CLOSE request.
Cc: stable@vger.kernel.org
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc00bc83f2 upstream.
ΕΛΕΝΗ reported that ksmbd binds to the IPV6 wildcard (::) by default for
ipv4 and ipv6 binding. So IPV4 connections are successful only when
the Linux system parameter bindv6only is set to 0 [default value].
If this parameter is set to 1, then the ipv6 wildcard only represents
any IPV6 address. Samba creates different sockets for ipv4 and ipv6
by default. This patch off sk_ipv6only to support IPV4/IPV6 connections
without creating two sockets.
Cc: stable@vger.kernel.org
Reported-by: ΕΛΕΝΗ ΤΖΑΒΕΛΛΑ <helentzavellas@yahoo.gr>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a4b49bb58 upstream.
regulator_get() may sometimes be called more than once for the same
consumer device, something which before commit dbe954d8f1 ("regulator:
core: Avoid debugfs: Directory ... already present! error") resulted in
errors being logged.
A couple of recent commits broke the handling of such cases so that
attributes are now erroneously created in the debugfs root directory the
second time a regulator is requested and the log is filled with errors
like:
debugfs: File 'uA_load' in directory '/' already present!
debugfs: File 'min_uV' in directory '/' already present!
debugfs: File 'max_uV' in directory '/' already present!
debugfs: File 'constraint_flags' in directory '/' already present!
on any further calls.
Fixes: 2715bb11cf ("regulator: core: Fix more error checking for debugfs_create_dir()")
Fixes: 08880713ce ("regulator: core: Streamline debugfs operations")
Cc: stable@vger.kernel.org
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240509133304.8883-1-johan+linaro@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d5887dc6b6 upstream.
Sandisk SN530 NVMe drives have broken MSIs. On systems without MSI-X
support, all commands time out resulting in the following message:
nvme nvme0: I/O tag 12 (100c) QID 0 timeout, completion polled
These timeouts cause the boot to take an excessively-long time (over 20
minutes) while the initial command queue is flushed.
Address this by adding a quirk for drives with buggy MSIs. The lspci
output for this device (recorded on a system with MSI-X support) is:
02:00.0 Non-Volatile memory controller: Sandisk Corp Device 5008 (rev 01) (prog-if 02 [NVM Express])
Subsystem: Sandisk Corp Device 5008
Flags: bus master, fast devsel, latency 0, IRQ 16, NUMA node 0
Memory at f7e00000 (64-bit, non-prefetchable) [size=16K]
Memory at f7e04000 (64-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 3
Capabilities: [90] MSI: Enable- Count=1/32 Maskable- 64bit+
Capabilities: [b0] MSI-X: Enable+ Count=17 Masked-
Capabilities: [c0] Express Endpoint, MSI 00
Capabilities: [100] Advanced Error Reporting
Capabilities: [150] Device Serial Number 00-00-00-00-00-00-00-00
Capabilities: [1b8] Latency Tolerance Reporting
Capabilities: [300] Secondary PCI Express
Capabilities: [900] L1 PM Substates
Kernel driver in use: nvme
Kernel modules: nvme
Cc: <stable@vger.kernel.org>
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c88033efe9 upstream.
Userfaultfd unregister includes a step to remove wr-protect bits from all
the relevant pgtable entries, but that only covered an explicit
UFFDIO_UNREGISTER ioctl, not a close() on the userfaultfd itself. Cover
that too. This fixes a WARN trace.
The only user visible side effect is the user can observe leftover
wr-protect bits even if the user close()ed on an userfaultfd when
releasing the last reference of it. However hopefully that should be
harmless, and nothing bad should happen even if so.
This change is now more important after the recent page-table-check
patch we merged in mm-unstable (446dd9ad37d0 ("mm/page_table_check:
support userfault wr-protect entries")), as we'll do sanity check on
uffd-wp bits without vma context. So it's better if we can 100%
guarantee no uffd-wp bit leftovers, to make sure each report will be
valid.
Link: https://lore.kernel.org/all/000000000000ca4df20616a0fe16@google.com/
Fixes: f369b07c86 ("mm/uffd: reset write protection when unregister with wp-mode")
Analyzed-by: David Hildenbrand <david@redhat.com>
Link: https://lkml.kernel.org/r/20240422133311.2987675-1-peterx@redhat.com
Reported-by: syzbot+d8426b591c36b21c750e@syzkaller.appspotmail.com
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Cc: Nadav Amit <nadav.amit@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e6423441b upstream.
In commit 0518dbe97f ("selftests/mm: fix cross compilation with LLVM")
the logic to detect the machine architecture in the Makefile was changed
to use ARCH, and only fallback to uname -m if ARCH is unset. However the
tests of ARCH were not updated to account for the fact that ARCH is
"powerpc" for powerpc builds, not "ppc64".
Fix it by changing the checks to look for "powerpc", and change the
uname -m logic to convert "ppc64.*" into "powerpc".
With that fixed the following tests now build for powerpc again:
* protection_keys
* va_high_addr_switch
* virtual_address_range
* write_to_hugetlbfs
Link: https://lkml.kernel.org/r/20240506115825.66415-1-mpe@ellerman.id.au
Fixes: 0518dbe97f ("selftests/mm: fix cross compilation with LLVM")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org> [6.4+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 720a22fd6c upstream.
With 'iommu=off' on the kernel command line and x2APIC enabled by the BIOS
the code which disables the x2APIC triggers an unchecked MSR access error:
RDMSR from 0x802 at rIP: 0xffffffff94079992 (native_apic_msr_read+0x12/0x50)
This is happens because default_acpi_madt_oem_check() selects an x2APIC
driver before the x2APIC is disabled.
When the x2APIC is disabled because interrupt remapping cannot be enabled
due to 'iommu=off' on the command line, x2apic_disable() invokes
apic_set_fixmap() which in turn tries to read the APIC ID. This triggers
the MSR warning because x2APIC is disabled, but the APIC driver is still
x2APIC based.
Prevent that by adding an argument to apic_set_fixmap() which makes the
APIC ID read out conditional and set it to false from the x2APIC disable
path. That's correct as the APIC ID has already been read out during early
discovery.
Fixes: d10a904435 ("x86/apic: Consolidate boot_cpu_physical_apicid initialization sites")
Reported-by: Adrian Huang <ahuang12@lenovo.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Adrian Huang <ahuang12@lenovo.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/875xw5t6r7.ffs@tglx
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a26ff37e62 upstream.
net_alloc_generic is called by net_alloc, which is called without any
locking. It reads max_gen_ptrs, which is changed under pernet_ops_rwsem. It
is read twice, first to allocate an array, then to set s.len, which is
later used to limit the bounds of the array access.
It is possible that the array is allocated and another thread is
registering a new pernet ops, increments max_gen_ptrs, which is then used
to set s.len with a larger than allocated length for the variable array.
Fix it by reading max_gen_ptrs only once in net_alloc_generic. If
max_gen_ptrs is later incremented, it will be caught in net_assign_generic.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com>
Fixes: 073862ba5d ("netns: fix net_alloc_generic()")
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240502132006.3430840-1-cascardo@igalia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 819fe8c96a upstream.
There are two issues with SDHC2 configuration for SA8155P-ADP,
which prevent use of SDHC2 and causes issues with ethernet:
- Card Detect pin for SHDC2 on SA8155P-ADP is connected to gpio4 of
PMM8155AU_1, not to SoC itself. SoC's gpio4 is used for DWMAC
TX. If sdhc driver probes after dwmac driver, it reconfigures
gpio4 and this breaks Ethernet MAC.
- pinctrl configuration mentions gpio96 as CD pin. It seems it was
copied from some SM8150 example, because as mentioned above,
correct CD pin is gpio4 on PMM8155AU_1.
This patch fixes both mentioned issues by providing correct pin handle
and pinctrl configuration.
Fixes: 0deb2624e2 ("arm64: dts: qcom: sa8155p-adp: Add support for uSD card")
Cc: stable@vger.kernel.org
Signed-off-by: Volodymyr Babchuk <volodymyr_babchuk@epam.com>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20240412190310.1647893-1-volodymyr_babchuk@epam.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
