[ Upstream commit deb24e64c8 ]
[Why & How]
Observe that we try to access DPCD 0x600h of disconnected DP ports.
In order not to wasting time on retrying these ports, call
dpcd_write_rx_power_ctrl() after checking its connection status.
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c1a467372 ]
[Why & How]
When MST config is unplugged/replugged too quickly, it can potentially
result in a scenario where previous DC state has not been reset before
the HPD link detection sequence begins. In this case, driver will
disable the streams/link prior to re-enabling the link for link
training.
There is a bug in the current logic that does not account for the fact
that current_state can be released and cleared prior to swapping to a
new state (resulting in the pipe_ctx stream pointers to be cleared) in
between disabling streams.
To resolve this, cache the original streams prior to committing any
stream updates.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 1561782686)
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a7fde4332 ]
[Why]
DP spec updated to have the CR AUX RD interval match the EQ AUX RD
interval interpretation of DPCD 0000Eh/0220Eh for 8b/10b non-LTTPR mode
and LTTPR transparent mode cases.
[How]
Update interpretation of DPCD 0000Eh/0220Eh for CR AUX RD interval
during 8b/10b link training.
Reviewed-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8bffa52e0 ]
[Why]
Setting link DPMS off in response to HPD disconnect creates AUX
transactions on a link that is supposed to be disconnected. This can
cause issues in some cases when the sink re-asserts HPD and expects
source to re-enable the link.
[How]
Avoid AUX transactions on disconnected link.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de84d58012 ]
[Why]
The latest DP spec requires the DP TX to read DPCD F0000h through F0009h
when detecting LTTPR capabilities for the first time.
[How]
Update LTTPR cap retrieval to read up to F0009h (two more bytes than the
previous F0007h), and store the LTTPR ALPM capabilities.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0584bbcf0c ]
[Why/How]
Certain PCON will clear the FRL_MODE bit despite supporting the link BW
indicated in the other bits.
Thus, skip checking the FRL_MODE bit when interpreting the
hdmi_encoded_link_bw struct.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[WHY]
We intend to consolidate dp tunneling and conventional dp link training.
[HOW]
1. Use the same link training entry for both dp and dpia
2. Move SET_CONFIG of non-transparent mode to dmub side
3. Add set_tps_notification dmub_cmd to notify tps request for
non-transparent dpia link training
4. Check dpcd request result and abort link training early if dpia
aux tunneling fails
5. Add option to avoid affect old product
6. Separately handle wait_time_microsec for dpia
Reviewed-by: Cruise Hung <cruise.hung@amd.com>
Reviewed-by: George Shen <george.shen@amd.com>
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Peichen Huang <PeiChen.Huang@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
There are some monitor timings that seem to be supported without
DSC but actually require DSC to be displayed. A VESA SCR introduced
a new max uncompressed pixel rate cap register that we can use to
handle these edge cases.
[HOW]
SST: Read caps from link and invalidate timings that exceed the
max limit but do not support DSC. Then check for options override
when determining BPP.
MST: Read caps from virtual DPCD peer device or daisy chained SST
monitor and set validation set BPPs to max if pixel rate exceeds
uncompressed limit. Validation set optimization continues as normal.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Ryan Seto <ryanseto@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Supporting UHBR10 link rate on eDP leverages
the existing DP2.0 code but need to add some small
adjustments in code.
[how]
Acknowledge the given DPCD caps for UHBR10
link rate support and allow DP2.0 programming
sequence and link training for eDP.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Sung Joon Kim <Sungjoon.Kim@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
eDP 2.0 is introducing support for UHBR link rates, however current eDP ILR
link optimization does not account for UHBR capabilities.
Either UHBR capabilities will be provided via the same 128b/132b rate DPCD caps
that are currently used on DP2.1, or Table 4-13 may be updated to include UHBR
rates.
[HOW]
Add extra Supported Link Rates table translations for UHBR10/13.5/20.
Update eDP link setting optimization search to be aware of 128b/132b DPCD
rate caps in order to unblock UHBR on panels with Supported Link Rates table.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Previous multi-display HPO fix moved where HPO I/O enable/disable is performed.
The codepath now taken to enable/disable HPO I/O is not used for compliance
test automation, meaning that if a compliance box being driven at a DP1 rate
requests retrain at UHBR, HPO I/O will remain off if it was previously off.
[HOW]
Explicitly update HPO I/O after allocating encoders for test request.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Under autonomous mode, source reads dpcd DP_PCON_HDMI_POST_FRL_STATUS
for the frl link status.
Without dsc passthrough, it serves as bw bottleneck on the entire link,
compared with the dp link from source to the converter where dsc is
available.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
sampling_rate is an uint8_t but is assigned an unsigned int, and thus it
can overflow. As a result, sampling_rate is changed to uint32_t.
Similarly, LINK_QUAL_PATTERN_SET has a size of 2 bits, and it should
only be assigned to a value less or equal than 4.
This fixes 2 INTEGER_OVERFLOW issues reported by Coverity.
Signed-off-by: Alex Hung <alex.hung@amd.com>
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT & HOW]
Functions dp_enable_link_phy and dp_disable_link_phy can pass link_res
without initializing hpo_dp_link_enc and it is necessary to check for
null before dereferencing.
This fixes 1 FORWARD_NULL issue reported by Coverity.
Fixes: 0beca868cd ("drm/amd/display: Check link_res->hpo_dp_link_enc before using it")
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT & HOW]
Poniters, such as stream_enc and dc->bw_vbios, are null checked previously
in the same function, so Coverity warns "implies that stream_enc and
dc->bw_vbios might be null". They are used multiple times in the
subsequent code and need to be checked.
This fixes 10 FORWARD_NULL issues reported by Coverity.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT & HOW]
Poniters, such as dc->clk_mgr, are null checked previously in the same
function, so Coverity warns "implies that "dc->clk_mgr" might be null".
As a result, these pointers need to be checked when used again.
This fixes 10 FORWARD_NULL issues reported by Coverity.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT & HOW]
Functions dp_enable_link_phy and dp_disable_link_phy can pass link_res
without initializing hpo_dp_link_enc and it is necessary to check for
null before dereferencing.
This fixes 2 FORWARD_NULL issues reported by Coverity.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Hotplugging with a DVI-DP dongle on pre-rdna embedded platform
working about half the time. The regression was found to be the
setting of link->type here.
[what]
Reverts fix besides the logging added.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Gabe Teeger <gabe.teeger@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The mux to switch between refclk and dto_dsc_clk is non double buffered.
However dto dsc clk's phase and modulo divider registers are currently
configured as double buffered update. This causes a problem when we switch to
use dto dsc clk and program phase and modulo in the same sequence. In this
sequence dsc clk is switched to dto but the clock divider programming doesn't
take effect until next frame. When we try to program DSCC registers, SMN bus
will hang because dto dsc clk divider phase is set to 0.
[how]
Configure phase and modulo to take effect immediately. Always switch to dto dsc
clk before DSC clock is unagted. Switch back to refclk after DSC clock is gated.
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Reviewed-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When assert in dp_retrieve_lttpr_cap() is hit, dmesg has traces like:
RIP: 0010:dp_retrieve_lttpr_cap+0xcc/0x1a0 [amdgpu]
Call Trace:
<TASK>
dp_retrieve_lttpr_cap+0xcc/0x1a0 [amdgpu]
report_bug+0x1e8/0x240
handle_bug+0x46/0x80
link_detect+0x35/0x580 [amdgpu]
It happens when LTTPRs fail to increment dpcd repeater count.
We have a recovery action in place for such cases.
Assert is misleading, an indicative error in dmesg is more useful.
[How]
Remove ASSERT and use DC_LOG_ERROR instead.
Reviewed-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When building the kernel-doc, it complains with the below warning:
./drivers/gpu/drm/amd/display/dc/link/hwss/link_hwss_dio.h:1: warning: no structured comments found
./drivers/gpu/drm/amd/display/dc/link/hwss/link_hwss_dio.h:1: warning: no structured comments found
This warning was caused by the wrong use of the ':export:' and the lack
of function documentation in the file pointed under the ':internal:'.
This commit addresses those issues by relocating the overview
documentation to the correct C file, removing the ':export:' options,
and adding two simple kernel-doc to ensure that ':internal:' does not
have any warning.
Cc: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/dri-devel/20240715085918.68f5ecc9@canb.auug.org.au/
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT & HOW]
Integer multiplies integer may overflow in context that expects an
expression of unsigned/siged long long (64 bits). This can be fixed
by casting integer to unsigned/siged long long to force 64 bits results.
This fixes 26 OVERFLOW_BEFORE_WIDEN issues reported by Coverity.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT & HOW]
Function return values must be checked before data can be used
in subsequent functions.
This fixes 4 CHECKED_RETURN issues reported by Coverity.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT & HOW]
The null checks for pipe_ctx->stream and pipe_ctx->stream_res.tg
are redundant as they were already dereferenced previously, as
reported by Coverity; therefore the null checks are removed.
This fixes 6 REVERSE_INULL issues reported by Coverity.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Coverity analysis of the Upstream display driver code
(amd-staging-drm-next) flagged these three functions as
containing 'CONSTANT_EXPRESSION_RESULT' errors, i. e. the
conditionals are reduntant since their result is predetermined.
fixpt31_32.c:
The two flagged 'ASSERT' lines redundant since they are always true:
- LONG_MAX equals to the largest 'signed long long' number
- res.value is type 'signed long long',
So, the condition inside the 'ASSERTS's is always
link_dp_training.c:
The flagged conditional statement is always false:
- 'max_requested.FFE_PRESET.settings.level' is 4 bits, so its max
possible value is 15
- 'DP_FFE_PRESET_MAX_LEVEL' equals to 15.
So, the conditional statement is always false and the wrapped code
never executes.
[HOW]
Removed lines flagged by Coverity analysis.
Reviewed-by: Sun peng Li <sunpeng.li@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Ivan Lipski <ivlipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
We set preferred link settings for virtual signal. However we don't support
virtual signal for UHBR link rate. If preferred is set to UHBR link rate, we
will allow virtual signal with UHBR link rate which causes system crashes.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Passive DP40 cables were updated in the latest DP spec to support
UHBR13.5 link rate. Current max link rate logic checks against the
cable ID DPCD even for passive cables.
[How]
Ignore UHBR13.5 cable ID DPCD cap in get_max_link_rate logic.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Some sinks are observed to return invalid LTTPR revision and/or invalid
LTTPR link rate capabilities.
[HOW]
Assume any LTTPR which reports invalid max link rate supports HBR3.
Don't validate LTTPR DPCD revision in dp_is_lttpr_present check.
Reviewed-by: George Shen <george.shen@amd.com>
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Needed for PHY patterns as well to perform electrical compliance.
Also need to increase wait time from 30ms to 50ms to resolve very
intermittent UHBR20 link training failures.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
In newer DCN's the programming of SYMCLK_FE_SRC_SEL depends on
the value of DIG_FE_SOURCE_SELECT. If DIG_FE_SOURCE_SELECT is not
already programmed at the time of PHY / DIG enable then the FW
sequence will program an incorrect SYMCLK source. Ensure that we
program DIG_FE_SOURCE_SELECT for all DIO scenarios (DVI in this
particular case) before going through the PHY / DIG enable sequence.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently there's an issue on DCN401 that prevents oled eDP panels from
being lit up that is still under investigation. To unblock dev work
while investigating, we can work around the issue by skipping toggling
the enablement of the backlight.
[How]
- new debug bit that will skip touching backlight enable DPCD for oled
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
In order to support glitchless display clock ramping for virtual stream,
we must
turn on symclk for stream encoder. The code will power on phy and enable
symclk
for dio encoder during virtual stream dpms sequence.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This commit modifies the construct_phy function to handle the case where
`bios->integrated_info` is NULL and to address a compiler warning about
a large stack allocation.
Upon examination, it was found that the local `integrated_info`
structure was just used to copy values which is large and was being
declared directly on the stack which could potentially lead to
performance issues. This commit changes the code to use
`bios->integrated_info` directly, which avoids the need for a large
stack allocation.
The function now checks if `bios->integrated_info` is NULL before
entering a for loop that uses it. If `bios->integrated_info` is NULL,
the function skips the for loop and continues executing the rest of the
code. This ensures that the function behaves correctly when
`bios->integrated_info` is NULL and improves compatibility with dGPUs.
Fixes the below with gcc W=1:
drivers/gpu/drm/amd/amdgpu/../display/dc/link/link_factory.c: In function ‘construct_phy’:
drivers/gpu/drm/amd/amdgpu/../display/dc/link/link_factory.c:743:1: warning: the frame size of 1056 bytes is larger than 1024 bytes [-Wframe-larger-than=]
Cc: Wenjing Liu <wenjing.liu@amd.com>
Cc: Jerry Zuo <jerry.zuo@amd.com>
Cc: Qingqing Zhuo <qingqing.zhuo@amd.com>
Cc: Tom Chung <chiahsuan.chung@amd.com>
Cc: Alvin Lee <alvin.lee2@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Roman Li <roman.li@amd.com>
Cc: Hersen Wu <hersenxs.wu@amd.com>
Cc: Alex Hung <alex.hung@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Suggested-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
'aux_payloads' is unused since
commit eae5ffa9bd ("drm/amd/display: Switch ddc to new aux interface")
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When the link BW is smaller than the request BW,
the DP LT just kept running and fallback to lower link config.
DP LT just aborted if is_hpd_pending bit is high.
But is_hpd_pending bit indicates a new HPD event received.
It doesn't mean the HPD is low.
[How]
Abort the DP LT if the link BW is smaller than the request BW.
Remove checking is_hpd_pending bit in DP LT.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Cruise <cruise.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
UHBR13.5 support is optional, even if UHBR20 is supported by the device.
If source supports max UHBR13.5 while sink, cable and LTTPR support
UHBR20 but not UHBR13.5, UHBR10 should be used as the max link cap.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
