Pull MTD updates from Miquel Raynal:
"MTD:
- Simon Glass wanted to support binman's output properties in order
to check their validity using the binding checks and proposed
changes with the missing properties as well as a binman compatible.
- Krzysztof Kozlowski on his side shared a new yaml for describing
Samsung's OneNAND interface.
- The interface with NVMEM has also been slightly improved/fixed,
especially now that OTP are also supported in the NAND subsystem.
- Along with these changes, small cleanups have also been contributed
around ID tables, structure sizes, arithmetic checks and comments.
Raw NAND subsystem:
- Two small fixes, one in the Hynix vendor code for properly
returning an error which might have been ignored and another in the
Davinci driver to properly synchronize the controller with the gpio
domain.
SPI NOR subsystem:
- SPI NOR now uses div_u64() instead of div64_u64() in places where
the divisor is 32 bits. Many 32 bit architectures can optimize this
variant better than a full 64 bit divide"
* tag 'mtd/for-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: spi-nor: replace unnecessary div64_u64() with div_u64()
mtd: mchp23k256: drop unneeded MODULE_ALIAS
dt-bindings: mtd: fixed-partition: Add binman compatibles
dt-bindings: mtd: fixed-partitions: Add alignment properties
mtd: maps: sa1100-flash: Prefer struct_size over open coded arithmetic
mtd: core: Align comment with an action in mtd_otp_nvmem_add()
mtd: rawnand: hynix: fixed typo
mtd: rawnand: davinci: Add dummy read after sending command
mtd: partitions: redboot: Added conversion of operands to a larger type
dt-bindings: mtd: Add Samsung S5Pv210 OneNAND
mtd: core: Don't fail mtd_otp_nvmem_add() if OTP is unsupported
mtd: core: Report error if first mtd_otp_size() call fails in mtd_otp_nvmem_add()
I ran into a randconfig build failure with UBSAN using gcc-13.2:
arm-linux-gnueabi-ld: error: unplaced orphan section `.bss..Lubsan_data31' from `drivers/mtd/nand/raw/diskonchip.o'
I'm not entirely sure what is going on here, but I suspect this has something
to do with the check for the end of the doc_locations[] array that contains
an (unsigned long)0xffffffff element, which is compared against the signed
(int)0xffffffff. If this is the case, we should get a runtime check for
undefined behavior, but we instead get an unexpected build-time error.
I would have expected this to work fine on 32-bit architectures despite the
signed integer overflow, though on 64-bit architectures this likely won't
ever work.
Changing the contition to instead check for the size of the array makes the
code safe everywhere and avoids the ubsan check that leads to the link
error. The loop code goes back to before 2.6.12.
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240405143015.717429-1-arnd@kernel.org
While migrating to exec_ops in commit a82990c8a4 ("mtd: rawnand: qcom:
Add read/read_start ops in exec_op path"), OP_RESET_DEVICE command handling
got broken unintentionally. Right now for the OP_RESET_DEVICE command,
qcom_misc_cmd_type_exec() will simply return 0 without handling it. Even,
if that gets fixed, an unnecessary FLASH_STATUS read descriptor command is
being added in the middle and that seems to be causing the command to fail
on IPQ806x devices.
So let's fix the above two issues to make OP_RESET_DEVICE command working
again.
Fixes: a82990c8a4 ("mtd: rawnand: qcom: Add read/read_start ops in exec_op path")
Cc: stable@vger.kernel.org
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240404083157.940-1-ansuelsmth@gmail.com
The function hynix_nand_rr_init() should probably return an error code.
Judging by the usage, it seems that the return code is passed up
the call stack.
Right now, it always returns 0 and the function hynix_nand_cleanup()
in hynix_nand_init() has never been called.
Found by RASU JSC and Linux Verification Center (linuxtesting.org)
Fixes: 626994e074 ("mtd: nand: hynix: Add read-retry support for 1x nm MLC NANDs")
Signed-off-by: Maxim Korotkov <korotkov.maxim.s@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240313102721.1991299-1-korotkov.maxim.s@gmail.com
Sometimes, writes fail because the tWB_max is not correctly observed
after sending PAGEPROG. It leads to the R/B pin to be read as in
the "ready" state right after sending the command, thus preventing the
normal tPROG delay to be actually observed. This happens because the
ndelay() that waits for tWB_max starts before the command reaches the
NAND chip.
Add a dummy read when a delay is requested at the end of the executed
instruction to make sure that the sent command is received by the NAND
before starting the short ndelay() (<1us but rounded up to 1us in
practice). This read is done on the control register area because
doing it on the Async Data area would change the NAND's RE pin state.
This is not perfect as the two areas are behind two different
devm_ioremap_resource() and could possibly be located on different
interconnects (I did not find more details). This means either the
additional latency due to the load operation is enough impacting, or it
has the expected behavior of ensuring the write has been received.
This has been tested on two platforms designed off of the
DAVINCI/OMAP-L138. The first uses a Toshiba NAND Flash (TC58NYG2S3EBAI5),
the other a Macronix one (MX30UF4G18AC).
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240308074609.9056-1-bastien.curutchet@bootlin.com
Pull MTD updates from Miquel Raynal:
"MTD:
- The Carillo Ranch driver has been removed
- Top level mtd bindings have received a couple of improvements
(references, selects)
- The ssfdc driver received few minor adjustments
- The usual load of misc/small improvements and fixes
Raw NAND:
- The main series brought is an update of the Broadcom support to
support all BCMBCA SoCs and their specificity (ECC, write
protection, configuration straps), plus a few misc fixes and
changes in the main driver. Device tree updates are also part of
this PR, initially because of a misunderstanding on my side.
- The STM32_FMC2 controller driver is also upgraded to properly
support MP1 and MP25 SoCs.
- A new compatible is added for an Atmel flavor.
- Among all these feature changes, there is as well a load of
continuous read related fixes, avoiding more corner conditions and
clarifying the logic. Finally a few miscellaneous fixes are made to
the core, the lpx32xx_mlc, fsl_lbc, Meson and Atmel controller
driver, as well as final one in the Hynix vendor driver.
SPI-NAND:
- The ESMT support has been extended to match 5 bytes ID to avoid
collisions. Winbond support on its side receives support for
W25N04KV chips.
SPI NOR:
- SPI NOR gets the non uniform erase code cleaned. We stopped using
bitmasks for erase types and flags, and instead introduced
dedicated members. We then passed the SPI NOR erase map to MTD.
Users can now determine the erase regions and make informed
decisions on partitions size.
- An optional interrupt property is now described in the bindings"
* tag 'mtd/for-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (50 commits)
mtd: rawnand: Ensure continuous reads are well disabled
mtd: rawnand: Constrain even more when continuous reads are enabled
mtd: rawnand: brcmnand: Add support for getting ecc setting from strap
mtd: rawnand: brcmnand: fix sparse warnings
mtd: nand: raw: atmel: Fix comment in timings preparation
mtd: rawnand: Ensure all continuous terms are always in sync
mtd: rawnand: Add a helper for calculating a page index
mtd: rawnand: Fix and simplify again the continuous read derivations
mtd: rawnand: hynix: remove @nand_technology kernel-doc description
dt-bindings: atmel-nand: add microchip,sam9x7-pmecc
mtd: rawnand: brcmnand: Support write protection setting from dts
mtd: rawnand: brcmnand: Add BCMBCA read data bus interface
mtd: rawnand: brcmnand: Rename bcm63138 nand driver
arm64: dts: broadcom: bcmbca: Update router boards
arm64: dts: broadcom: bcmbca: Add NAND controller node
ARM: dts: broadcom: bcmbca: Add NAND controller node
mtd: spi-nor: core: correct type of i
mtd: spi-nor: core: set mtd->eraseregions for non-uniform erase map
mtd: spi-nor: core: get rid of SNOR_OVERLAID_REGION flag
mtd: spi-nor: core: get rid of SNOR_LAST_REGION flag
...
The cont_read.ongoing flag should only be enabled at the beginning of a
read operation, and also disabled at its end, so we never end up
triggering nasty side effects outside of this scope. The mtd core being
highly serialized, we should not be bothered by parallel accesses
anyway.
In case we reach the end of a read operation and the boolean was not
properly disabled, it's a bug, but it's totally manageable. So warn, and
then fix the boolean state.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240307115315.1942678-2-miquel.raynal@bootlin.com
As a matter of fact, continuous reads require additional handling at the
operation level in order for them to work properly. The core helpers do
have this additional logic now, but any time a controller implements its
own page helper, this extra logic is "lost". This means we need another
level of per-controller driver checks to ensure they can leverage
continuous reads. This is for now unsupported, so in order to ensure
continuous reads are enabled only when fully using the core page
helpers, we need to add more initial checks.
Also, as performance is not relevant during raw accesses, we also
prevent these from enabling the feature.
This should solve the issue seen with controllers such as the STM32 FMC2
when in sequencer mode. In this case, the continuous read feature would
be enabled but not leveraged, and most importantly not disabled, leading
to further operations to fail.
Reported-by: Christophe Kerello <christophe.kerello@foss.st.com>
Fixes: 003fe4b954 ("mtd: rawnand: Support for sequential cache reads")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Christophe Kerello <christophe.kerello@foss.st.com>
Link: https://lore.kernel.org/linux-mtd/20240307115315.1942678-1-miquel.raynal@bootlin.com
While crossing a LUN boundary, it is probably safer (and clearer) to
keep all members of the continuous read structure aligned, including the
pause page (which is the last page of the lun or the last page of the
continuous read). Once these members properly in sync, we can use the
rawnand_cap_cont_reads() helper everywhere to "prepare" the next
continuous read if there is one.
Fixes: bbcd80f53a ("mtd: rawnand: Prevent crossing LUN boundaries during sequential reads")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240223115545.354541-4-miquel.raynal@bootlin.com
clang-16 warns about mismatched function prototypes:
drivers/mtd/nand/raw/lpc32xx_mlc.c:783:29: error: cast from 'irqreturn_t (*)(int, struct lpc32xx_nand_host *)' (aka 'enum irqreturn (*)(int, struct lpc32xx_nand_host *)') to 'irq_handler_t' (aka 'enum irqreturn (*)(int, void *)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
Change the interrupt handler to the normal way of just passing
a void* pointer and converting it inside the function..
Fixes: 70f7cb78ec ("mtd: add LPC32xx MLC NAND driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240213100146.455811-1-arnd@kernel.org
The check in nand_base.c, nand_scan_tail() : has the following code:
(ecc->steps * ecc->size != mtd->writesize) which fails for some NAND chips.
Remove ECC entries in this driver which are not integral multiplications,
and adjust the number of chunks for entries which fails the above
calculation so it will calculate correctly (this was previously done
automatically before the check and was removed in a later commit).
Fixes: 68c18dae68 ("mtd: rawnand: marvell: add missing layouts")
Cc: stable@vger.kernel.org
Signed-off-by: Elad Nachman <enachman@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
* Raw NAND
The most meaningful change being the conversion of the brcmnand driver
to the ->exec_op() API, this series brought additional changes to the
core in order to help controller drivers to handle themselves the WP pin
during destructive operations when relevant.
As always, there is as well a whole bunch of miscellaneous W=1 fixes,
together with a few runtime fixes (double free, timeout value, OOB
layout, missing register initialization) and the usual load of remove
callbacks turned into void (which led to switch the txx9ndfmc driver to
use module_platform_driver()).
The current logic is probably fine but is a bit convoluted. Plus, we
don't want partial pages to be part of the sequential operation just in
case the core would optimize the page read with a subpage read (which
would break the sequence). This may happen on the first and last page
only, so if the start offset or the end offset is not aligned with a
page boundary, better avoid them to prevent any risk.
Cc: stable@vger.kernel.org
Fixes: 003fe4b954 ("mtd: rawnand: Support for sequential cache reads")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Martin Hundebøll <martin@geanix.com>
Link: https://lore.kernel.org/linux-mtd/20231215123208.516590-5-miquel.raynal@bootlin.com
The ONFI specification states that devices do not need to support
sequential reads across LUN boundaries. In order to prevent such event
from happening and possibly failing, let's introduce the concept of
"pause" in the sequential read to handle these cases. The first/last
pages remain the same but any time we cross a LUN boundary we will end
and restart (if relevant) the sequential read operation.
Cc: stable@vger.kernel.org
Fixes: 003fe4b954 ("mtd: rawnand: Support for sequential cache reads")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Martin Hundebøll <martin@geanix.com>
Link: https://lore.kernel.org/linux-mtd/20231215123208.516590-2-miquel.raynal@bootlin.com
When nand_scan() fails, it has cleaned up related resources
in its error paths. Therefore, the following nand_cleanup()
may lead to a double-free. One possible trace is:
doc_probe
|-> nand_scan
| |-> nand_scan_with_ids
| |-> nand_scan_tail
| |-> kfree(chip->data_buf) [First free]
|
|-> nand_cleanup
|-> kfree(chip->data_buf) [Double free here]
Fix this by removing nand_cleanup() on failure of
nand_scan().
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20231214072946.10285-1-dinghao.liu@zju.edu.cn
Under heavy load it is likely that the controller is done
with its own task but the thread unlocking the wait is not
scheduled in time. Increasing IFC_TIMEOUT_MSECS allows the
controller to respond within allowable timeslice of 1 sec.
fsl,ifc-nand 7e800000.nand: Controller is not responding
[<804b2047>] (nand_get_device) from [<804b5335>] (nand_write_oob+0x1b/0x4a)
[<804b5335>] (nand_write_oob) from [<804a3585>] (mtd_write+0x41/0x5c)
[<804a3585>] (mtd_write) from [<804c1d47>] (ubi_io_write+0x17f/0x22c)
[<804c1d47>] (ubi_io_write) from [<804c047b>] (ubi_eba_write_leb+0x5b/0x1d0)
Fixes: 82771882d9 ("NAND Machine support for Integrated Flash Controller")
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ronald Monthero <debug.penguin32@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20231118083156.776887-1-debug.penguin32@gmail.com
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20231102220246.3336154-10-u.kleine-koenig@pengutronix.de
