The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
By changing the function brcmnand_remove() to return void several
drivers that use this function as remove callback can be converted to
.remove_new().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20231102220246.3336154-7-u.kleine-koenig@pengutronix.de
Pull mtd updates from Miquel Raynal:
"The main set of changes is related to Uwe's work converting platform
remove callbacks to return void. Comes next (in number of changes)
Kees' additional structures annotations to improve the sanitizers. The
usual amount of cleanups apply.
About the more substancial contribution, one main function of the
partitions core could return an error which was not checked, this is
now fixed. On the bindings side, fixed partitions can now have a
compression property. Finally, an erroneous situation is now always
avoided in the MAP RAM driver.
CFI:
- A several years old byte swap has been fixed.
NAND:
- The subsystem has, as usual, seen a bit of cleanup being done this
cycle, typically return values of platform_get_irq() and
devm_kasprintf(). There is also a better ECC check in the Arasan
driver. This comes with smaller misc changes.
- In the SPI-NAND world there is now support for Foresee F35SQA002G,
Winbond W25N and XTX XT26 chips.
SPI NOR:
- For SPI NOR we cleaned the flash info entries in order to have them
slimmer and self explanatory. In order to make the entries as slim
as possible, we introduced sane default values so that the actual
flash entries don't need to specify them. We now use a flexible
macro to specify the flash ID instead of the previous INFOx()
macros that had hardcoded ID lengths.
Instead of:
{ "w25q512nwm", INFO(0xef8020, 0, 64 * 1024, 0)
OTP_INFO(256, 3, 0x1000, 0x1000) },
We now use:
.id = SNOR_ID(0xef, 0x80, 0x20),
.name = "w25q512nwm",
.otp = SNOR_OTP(256, 3, 0x1000, 0x1000),
- We also removed some flash entries: the very old Catalyst SPI
EEPROMs that were introduced once with the SPI-NOR subsystem, and a
Fujitsu MRAM. Both should use the at25 EEPROM driver. The latter
even has device tree bindings for the at25 driver.
- We made sure that the conversion didn't introduce any unwanted
changes by comparing the .rodata segment before and after the
conversion. The patches landed in linux-next immediately after
v6.6-rc2, we haven't seen any regressions yet.
- Apart of the autumn cleaning we introduced a new flash entry,
at25ff321a, and added block protection support for mt25qu512a"
* tag 'mtd/for-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (91 commits)
mtd: cfi_cmdset_0001: Byte swap OTP info
mtd: rawnand: meson: check return value of devm_kasprintf()
mtd: rawnand: intel: check return value of devm_kasprintf()
mtd: rawnand: sh_flctl: Convert to module_platform_driver()
mtd: spi-nor: micron-st: use SFDP table for mt25qu512a
mtd: spi-nor: micron-st: enable lock/unlock for mt25qu512a
mtd: rawnand: Remove unused of_gpio.h inclusion
mtd: spinand: Add support for XTX XT26xxxDxxxxx
mtd: spinand: winbond: add support for serial NAND flash
mtd: rawnand: cadence: Annotate struct cdns_nand_chip with __counted_by
mtd: rawnand: Annotate struct mtk_nfc_nand_chip with __counted_by
mtd: spinand: add support for FORESEE F35SQA002G
mtd: rawnand: rockchip: Use struct_size()
mtd: rawnand: arasan: Include ECC syndrome along with in-band data while checking for ECC failure
mtd: Use device_get_match_data()
mtd: spi-nor: nxp-spifi: Convert to platform remove callback returning void
mtd: spi-nor: hisi-sfc: Convert to platform remove callback returning void
mtd: maps: sun_uflash: Convert to platform remove callback returning void
mtd: maps: sa1100-flash: Convert to platform remove callback returning void
mtd: maps: pxa2xx-flash: Convert to platform remove callback returning void
...
The raw NAND subsystem has, as usual, seen a bit of cleanup being done
this cycle, typically return values of platform_get_irq() and
devm_kasprintf(), plus structure annotations for sanitizers. There is
also a better ECC check in the Arasan driver. This comes with smaller
misc changes.
In the SPI-NAND world there is now support for Foresee F35SQA002G,
Winbond W25N and XTX XT26 chips.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Pull gpio updates from Bartosz Golaszewski:
"We don't have any new drivers. The loongson driver is getting extended
with support for new models. There's a big refactor of gpio-pca953x
and many small improvements to others.
The GPIO code in the kernel has acquired a lot of cruft over the years
as well as many abusers of the API across the kernel tree. This
release cycle we have started a major cleanup and improvement effort
that will most likely span several releases. We have started by
converting external users of struct gpio_chip to accessing the wrapper
around it - struct gpio_device. This is because the latter is
reference counted while the former is removed when the provider is
unbound. We also removed several instances of drivers accessing
private GPIOLIB structures and including the private header from
drivers/gpio/.
To that end you'll see several commits aimed at different subsystems
(acked by relevant maintainers) as well as two merges from the
x86/platform tree.
We'll then rework the locking in GPIOLIB which currently uses a big
spinlock for many different things and could use becoming more
fine-grained, especially as it doesn't even get the locking right.
We'll also use SRCU for protecting the gpio_chip pointer against
in-kernel hot-unplug crashes similar to what we saw triggered from
user-space and fixed with semaphores in gpiolib-cdev. The core GPIOLIB
is still vulnerable to these use-cases. I'm just mentioning the plans
here, this is not part of this PR.
You'll see some new instances of using __free(). We've added a
gpio_device_put cleanup helper similar to the put_device one
introduced by Peter Zijlstra and used it according to the preferred
pattern except where it didn't make sense.
GPIOLIB core:
- provide interfaces allowing users to retrieve, manage and query the
reference counted GPIO device instead of accessing the private
gpio_chip structure
- replace gpiochip_find() with gpio_device_find()
- remove unused acpi_get_and_request_gpiod()
- improve the ignore_interrupt functionality in GPIO ACPI
- correct notifier return codes in gpiolib-of
- unexport gpiod_set_transitory() as it's unused outside of core GPIO
code
- while there are still external users accessing struct gpio_chip,
let's make gpiochip_get_desc() public so that they at least use the
preferred helper
- improve locking for lookup tables
- annotate struct linereq with __counted_by
- improve GPIOLIB docs
- add an OF quirk for LED trigger sources
Driver improvements:
- convert all GPIO drivers with .remove() callbacks to using the new
variant returning void instead of int
- stop accessing the GPIOLIB private structures in gpio-mockup,
i2c-mux-gpio, hte-tegra194, gpio-sim
- use the recommended pattern for autofree variables in gpio-sim
- add support for more models to gpio-loongson
- use a notifier chain to notify other blocks about interrupts in
gpio-eic-sprd instead of looking up GPIO devices on every interrupt
- convert gpio-pca953x and gpio-fx6408 to using the maple tree regmap
cache
- don't include GPIOLIB internal headers in drivers which don't need
them
- move the ingenic NAND quirk into gpiolib-of
- add an ignore interrupt quirk for Peaq C1010
- drop static GPIO base from gpio-omap, gpio-f7188x
- use the preferred device_get_match_data() function in drivers that
still don't
- refactor gpio-pca953x: switch to using DEFINE_SIMPLE_DEV_PM_OPS(),
use cleanup helpers, use dev_err_probe() where it makes sense,
fully convert to using devres and some other minor tweaks
DT bindings:
- add support for a new model to gpio-vf610 and update existing
properties
- add support for more loongson models
- add missing support for imx models that are used but undocumented
- convert bindings for Intel IXP4xx to schema
Minor stuff:
- deprecate gpio-mockup in favor of gpio-sim
- include missing headers here and there
- stop using gpiochip_find() in OMAP1 board files
- minor tweaks in gpio-vf610, gpio-hisi
- remove unneeded 'extern' specifiers from headers"
* tag 'gpio-updates-for-v6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (108 commits)
hte: tegra194: add GPIOLIB dependency
hte: tegra194: don't access struct gpio_chip
gpiolib: provide gpio_device_get_base()
i2c: mux: gpio: don't fiddle with GPIOLIB internals
gpiolib: provide gpiod_to_gpio_device()
gpiolib: provide gpio_device_to_device()
gpio: hisi: Fix format specifier
gpiolib: provide gpio_device_find_by_fwnode()
gpio: acpi: remove acpi_get_and_request_gpiod()
gpio: Use device_get_match_data()
gpio: vf610: update comment for i.MX8ULP and i.MX93 legacy compatibles
platform/x86: int3472: Switch to devm_get_gpiod()
platform/x86: int3472: Stop using gpiod_toggle_active_low()
platform/x86: int3472: Add new skl_int3472_gpiod_get_from_temp_lookup() helper
platform/x86: int3472: Add new skl_int3472_fill_gpiod_lookup() helper
gpio: vf610: simplify code by dropping data check
gpio: vf610: add i.MX8ULP of_device_id entry
dt-bindings: gpio: vf610: add i.MX95 compatible
dt-bindings: gpio: vf610: correct i.MX8ULP and i.MX93
dt-bindings: gpio: vf610: update gpio-ranges
...
Following an ECC failure condition upon page reads, we shall distinguish
between a real ECC failure and an empty page. This is handled with a call
to nand_check_erased_ecc_chunk() which looks at the data and counts the
number of bits which are not 'ones'. If we get less zeros than the ECC
strength, we assume the page was erased and we are in the presence of
natural bitflips. Otherwise, if we are above, we assume some data was
written and the ECC engine could not recover it all, so we report an ECC
failure.
In order for this logic to be as close as the reality as we can (this is
already a simplified condition but we can hardly be more precise), we
should check all the data that is covered by the ECC step not only the
in-band data, so we should also include the ECC syndrome in the check.
Fixes: 88ffef1b65 ("mtd: rawnand: arasan: Support the hardware BCH ECC engine")
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230927055621.2906454-1-amit.kumar-mahapatra@amd.com
Both the JEDEC and ONFI specification say that read cache sequential
support is an optional command. This means that we not only need to
check whether the individual controller supports the command, we also
need to check the parameter pages for both ONFI and JEDEC NAND flashes
before enabling sequential cache reads.
This fixes support for NAND flashes which don't support enabling cache
reads, i.e. Samsung K9F4G08U0F or Toshiba TC58NVG0S3HTA00.
Sequential cache reads are now only available for ONFI and JEDEC
devices, if individual vendors implement this, it needs to be enabled
per vendor.
Tested on i.MX6Q with a Samsung NAND flash chip that doesn't support
sequential reads.
Fixes: 003fe4b954 ("mtd: rawnand: Support for sequential cache reads")
Cc: stable@vger.kernel.org
Signed-off-by: Rouven Czerwinski <r.czerwinski@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230922141717.35977-1-r.czerwinski@pengutronix.de
The NAND core complies with the ONFI specification, which itself
mentions that after any program or erase operation, a status check
should be performed to see whether the operation was finished *and*
successful.
The NAND core offers helpers to finish a page write (sending the
"PAGE PROG" command, waiting for the NAND chip to be ready again, and
checking the operation status). But in some cases, advanced controller
drivers might want to optimize this and craft their own page write
helper to leverage additional hardware capabilities, thus not always
using the core facilities.
Some drivers, like this one, do not use the core helper to finish a page
write because the final cycles are automatically managed by the
hardware. In this case, the additional care must be taken to manually
perform the final status check.
Let's read the NAND chip status at the end of the page write helper and
return -EIO upon error.
Cc: Michal Simek <michal.simek@amd.com>
Cc: stable@vger.kernel.org
Fixes: 08d8c62164 ("mtd: rawnand: pl353: Add support for the ARM PL353 SMC NAND controller")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/linux-mtd/20230717194221.229778-3-miquel.raynal@bootlin.com
The NAND core complies with the ONFI specification, which itself
mentions that after any program or erase operation, a status check
should be performed to see whether the operation was finished *and*
successful.
The NAND core offers helpers to finish a page write (sending the
"PAGE PROG" command, waiting for the NAND chip to be ready again, and
checking the operation status). But in some cases, advanced controller
drivers might want to optimize this and craft their own page write
helper to leverage additional hardware capabilities, thus not always
using the core facilities.
Some drivers, like this one, do not use the core helper to finish a page
write because the final cycles are automatically managed by the
hardware. In this case, the additional care must be taken to manually
perform the final status check.
Let's read the NAND chip status at the end of the page write helper and
return -EIO upon error.
Cc: Michal Simek <michal.simek@amd.com>
Cc: stable@vger.kernel.org
Fixes: 88ffef1b65 ("mtd: rawnand: arasan: Support the hardware BCH ECC engine")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/linux-mtd/20230717194221.229778-2-miquel.raynal@bootlin.com
The NAND core complies with the ONFI specification, which itself
mentions that after any program or erase operation, a status check
should be performed to see whether the operation was finished *and*
successful.
The NAND core offers helpers to finish a page write (sending the
"PAGE PROG" command, waiting for the NAND chip to be ready again, and
checking the operation status). But in some cases, advanced controller
drivers might want to optimize this and craft their own page write
helper to leverage additional hardware capabilities, thus not always
using the core facilities.
Some drivers, like this one, do not use the core helper to finish a page
write because the final cycles are automatically managed by the
hardware. In this case, the additional care must be taken to manually
perform the final status check.
Let's read the NAND chip status at the end of the page write helper and
return -EIO upon error.
Cc: stable@vger.kernel.org
Fixes: 02f26ecf8c ("mtd: nand: add reworked Marvell NAND controller driver")
Reported-by: Aviram Dali <aviramd@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Ravi Chandra Minnikanti <rminnikanti@marvell.com>
Link: https://lore.kernel.org/linux-mtd/20230717194221.229778-1-miquel.raynal@bootlin.com
Pull MTD updates from Miquel Raynal:
"Core MTD changes:
- Use refcount to prevent corruption
- Call external _get and _put in right order
- Fix use-after-free in mtd release
- Explicitly include correct DT includes
- Clean refcounting with MTD_PARTITIONED_MASTER
- mtdblock: make warning messages ratelimited
- dt-bindings: Add SEAMA partition bindings
Device driver changes:
- Use devm helper functions
- Fix questionable cast, remove pointless ones.
- error handling fixes
- add support for new chip versions
- update DT bindings
- misc cleanups - fix typos, whitespace, indentation"
* tag 'mtd/for-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (105 commits)
dt-bindings: mtd: amlogic,meson-nand: drop unneeded quotes
mtd: spear_smi: Use helper function devm_clk_get_enabled()
mtd: rawnand: orion: Use helper function devm_clk_get_optional_enabled()
mtd: rawnand: vf610_nfc: Use helper function devm_clk_get_enabled()
mtd: rawnand: sunxi: Use helper function devm_clk_get_enabled()
mtd: rawnand: stm32_fmc2: Use helper function devm_clk_get_enabled()
mtd: rawnand: mtk: Use helper function devm_clk_get_enabled()
mtd: rawnand: mpc5121: Use helper function devm_clk_get_enabled()
mtd: rawnand: lpc32xx_slc: Use helper function devm_clk_get_enabled()
mtd: rawnand: intel: Use helper function devm_clk_get_enabled()
mtd: rawnand: fsmc: Use helper function devm_clk_get_enabled()
mtd: rawnand: arasan: Use helper function devm_clk_get_enabled()
mtd: rawnand: qcom: Add read/read_start ops in exec_op path
mtd: rawnand: qcom: Clear buf_count and buf_start in raw read
mtd: maps: fix -Wvoid-pointer-to-enum-cast warning
mtd: rawnand: fix -Wvoid-pointer-to-enum-cast warning
mtd: rawnand: fsmc: handle clk prepare error in fsmc_nand_resume()
mtd: rawnand: Propagate error and simplify ternary operators for brcmstb_nand_wait_for_completion()
mtd: rawnand: qcom: Sort includes alphabetically
mtd: rawnand: qcom: Do not override the error no of submit_descs()
...
Raw NAND core changes:
* Fix -Wvoid-pointer-to-enum-cast warning
* Export 'nand_exit_status_op()'
* dt-bindings: Fix nand-controller.yaml license
Raw NAND controller driver changes:
* Omap, Omap2, Samsung, Atmel, fsl_upm, lpc32xx_slc, lpc32xx_mlc, STM32_FMC2,
sh_ftlctl, MXC, Sunxi:
- Use devm_platform_get_and_ioremap_resource()
* Orion, vf610_nfc, Sunxi, STM32_FMC2, MTK, mpc5121, lpc32xx_slc, Intel,
FSMC, Arasan:
- Use helper function devm_clk_get_optional_enabled()
* Brcmnand:
- Use devm_platform_ioremap_resource_byname()
- Propagate init error -EPROBE_DEFER up
- Propagate error and simplify ternary operators
- Fix mtd oobsize
- Fix potential out-of-bounds access in oob write
- Fix crash during the panic_write
- Fix potential false time out warning
- Fix ECC level field setting for v7.2 controller
* fsmc: Handle clk prepare error in fsmc_nand_resume()
* Marvell: Add support for AC5 SoC
* Meson:
- Support for 512B ECC step size
- Fix build error
- Use NAND core API to check status
- dt-bindings:
* Make ECC properties dependent
* Support for 512B ECC step size
* Drop unneeded quotes
* Oxnas: Remove driver and bindings
* Qcom:
- Conversion to ->exec_op()
- Removal of the legacy interface
- Two full series of improvements/misc fixes
* Use the BIT() macro
* Use u8 instead of uint8_t
* Fix alignment with open parenthesis
* Fix the spacing
* Fix wrong indentation
* Fix a typo
* Early structure initialization
* Fix address parsing within ->exec_op()
* Remove superfluous initialization of "ret"
* Rename variables in qcom_op_cmd_mapping()
* Handle unsupported opcode in qcom_op_cmd_mapping()
* Fix the opcode check in qcom_check_op()
* Use EOPNOTSUPP instead of ENOTSUPP
* Wrap qcom_nand_exec_op() to 80 columns
* Unmap sg_list and free desc within submic_descs()
* Simplify the call to nand_prog_page_end_op()
* Do not override the error no of submit_descs()
* Sort includes alphabetically
* Clear buf_count and buf_start in raw read
* Add read/read_start ops in exec_op path
* vf610_nfc: Do not check 0 for platform_get_irq()
SPI-NAND changes:
* gigadevice: Add support for GD5F1GQ{4,5}RExxH
* esmt: Add support for F50D2G41KA
* toshiba: Add support for T{C,H}58NYG{0,2}S3HBAI4 and TH58NYG3S0HBAI6
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Since commit 7ef9651e97 ("clk: Provide new devm_clk helpers for prepared
and enabled clocks"), devm_clk_get_optional() and clk_prepare_enable() can
now be replaced by devm_clk_get_optional_enabled() when driver enables
(and possibly prepares) the clocks for the whole lifetime of the device.
Moreover, it is no longer necessary to unprepare and disable the clocks
explicitly, so drop the label "no_dev".
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230821031737.1973183-13-lizetao1@huawei.com
Since commit 7ef9651e97 ("clk: Provide new devm_clk helpers for prepared
and enabled clocks"), devm_clk_get() and clk_prepare_enable() can now be
replaced by devm_clk_get_enabled() when driver enables (and possibly
prepares) the clocks for the whole lifetime of the device. Moreover, it is
no longer necessary to unprepare and disable the clocks explicitly, so drop
the label "err_disable_clk".
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Since commit 7ef9651e97 ("clk: Provide new devm_clk helpers for prepared
and enabled clocks"), devm_clk_get() and clk_prepare_enable() can now be
replaced by devm_clk_get_enabled() when driver enables (and possibly
prepares) the clocks for the whole lifetime of the device. Moreover, it is
no longer necessary to unprepare and disable the clocks explicitly, so drop
the label "out_mod_clk_unprepare" and "out_ahb_clk_unprepare".
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230821031737.1973183-10-lizetao1@huawei.com
Since commit 7ef9651e97 ("clk: Provide new devm_clk helpers for prepared
and enabled clocks"), devm_clk_get() and clk_prepare_enable() can now be
replaced by devm_clk_get_enabled() when driver enables (and possibly
prepares) the clocks for the whole lifetime of the device. Moreover, it is
no longer necessary to unprepare and disable the clocks explicitly, so drop
the label "err_clk_disable".
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230821031737.1973183-9-lizetao1@huawei.com
Since commit 7ef9651e97 ("clk: Provide new devm_clk helpers for prepared
and enabled clocks"), devm_clk_get() and clk_prepare_enable() can now be
replaced by devm_clk_get_enabled() when driver enables (and possibly
prepares) the clocks for the whole lifetime of the device. Moreover, it is
no longer necessary to unprepare and disable the clocks explicitly, so drop
the label "clk_disable". And both mtk_nfc_enable_clk() and
mtk_nfc_disable_clk() now have a single user, which is the resume or
suspend callback, so drop this two helper function and just move related
operations in the resume or suspend function.
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230821031737.1973183-8-lizetao1@huawei.com
Since commit 7ef9651e97 ("clk: Provide new devm_clk helpers for prepared
and enabled clocks"), devm_clk_get() and clk_prepare_enable() can now be
replaced by devm_clk_get_enabled() when driver enables (and possibly
prepares) the clocks for the whole lifetime of the device. Moreover, it is
no longer necessary to unprepare and disable the clocks explicitly, so drop
the label "unprepare_clk".
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230821031737.1973183-6-lizetao1@huawei.com
Since commit 7ef9651e97 ("clk: Provide new devm_clk helpers for prepared
and enabled clocks"), devm_clk_get() and clk_prepare_enable() can now be
replaced by devm_clk_get_enabled() when driver enables (and possibly
prepares) the clocks for the whole lifetime of the device. Moreover, it is
no longer necessary to unprepare and disable the clocks explicitly, so drop
the label "err_disable_unprepare_clk".
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230821031737.1973183-5-lizetao1@huawei.com
Since commit 7ef9651e97 ("clk: Provide new devm_clk helpers for prepared
and enabled clocks"), devm_clk_get() and clk_prepare_enable() can now be
replaced by devm_clk_get_enabled() when driver enables (and possibly
prepares) the clocks for the whole lifetime of the device. Moreover, it is
no longer necessary to unprepare and disable the clocks explicitly. The
label "disable_clk" no longer makes sense, rename it to "disable_fsmc".
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230821031737.1973183-4-lizetao1@huawei.com
Since commit 7ef9651e97 ("clk: Provide new devm_clk helpers for prepared
and enabled clocks"), devm_clk_get() and clk_prepare_enable() can now be
replaced by devm_clk_get_enabled() when driver enables (and possibly
prepares) the clocks for the whole lifetime of the device. Moreover, it is
no longer necessary to unprepare and disable the clocks explicitly, so drop
the label "disable_bus_clk" and "disable_controller_clk".
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230821031737.1973183-3-lizetao1@huawei.com
There are two types of dma descriptors being used in this driver allocated
by, prepare_bam_async_desc() and prep_adm_dma_desc() helper functions.
These functions map and prepare the descriptors to be used for dma
transfers.
And all the descriptors are submitted inside the submit_descs() function.
Once the transfer completion happens, those descriptors should be unmapped
and freed as a part of cleanup.
Currently, free_descs() function is doing the said cleanup of descriptors.
But the callers of submit_descs() are required to call free_descs() in both
the success and error cases.
Since there are no other transactions need to be done after submit_descs(),
let's just move the contents of free_descs() inside submit_descs() itself.
This makes sure that the cleanup is handled within the submit_descs()
thereby offloading the cleanup part from callers.
While at it, let's also rename the return variable from "r" to "ret".
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230805174146.57006-8-manivannan.sadhasivam@linaro.org
