mmc: Disable CMD23 transfers on all cards
Pending wire-level investigation of these types of transfers
and associated errors on bcm2835-mmc, disable for now. Fallback of
CMD18/CMD25 transfers will be used automatically by the MMC layer.
Reported/Tested-by: Gellert Weisz <gellert@raspberrypi.org>
mmc: bcm2835-mmc: enable DT support for all architectures
Both ARCH_BCM2835 and ARCH_BCM270x are built with OF now.
Enable Device Tree support for all architectures.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
mmc: bcm2835-mmc: fix probe error handling
Probe error handling is broken in several places.
Simplify error handling by using device managed functions.
Replace pr_{err,info} with dev_{err,info}.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2835-mmc: Add locks when accessing sdhost registers
bcm2835-mmc: Add range of debug options for slowing things down
bcm2835-mmc: Add option to disable some delays
bcm2835-mmc: Add option to disable MMC_QUIRK_BLK_NO_CMD23
bcm2835-mmc: Default to disabling MMC_QUIRK_BLK_NO_CMD23
bcm2835-mmc: Adding overclocking option
Allow a different clock speed to be substitued for a requested 50MHz.
This option is exposed using the "overclock_50" DT parameter.
Note that the mmc interface is restricted to EVEN integer divisions of
250MHz, and the highest sensible option is 63 (250/4 = 62.5), the
next being 125 (250/2) which is much too high.
Use at your own risk.
bcm2835-mmc: Round up the overclock, so 62 works for 62.5Mhz
Also only warn once for each overclock setting.
mmc: bcm2835-mmc: Make available on ARCH_BCM2835
Make the bcm2835-mmc driver available for use on ARCH_BCM2835.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270x_DT: add bcm2835-mmc entry
Add Device Tree entry for bcm2835-mmc.
In non-DT mode, don't add the device in the board file.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2835-mmc: Don't overwrite MMC capabilities from DT
bcm2835-mmc: Don't override bus width capabilities from devicetree
Take out the force setting of the MMC_CAP_4_BIT_DATA host capability
so that the result read from devicetree via mmc_of_parse() is
preserved.
bcm2835-mmc: Only claim one DMA channel
With both MMC controllers enabled there are few DMA channels left. The
bcm2835-mmc driver only uses DMA in one direction at a time, so it
doesn't need to claim two channels.
See: https://github.com/raspberrypi/linux/issues/1327
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-mmc: New timer API
mmc: bcm2835-mmc: Support underclocking
Support underclocking of the SD bus using the max-frequency DT property
(which currently has no DT parameter). The sd_overclock parameter
already provides another way to achieve the same thing which should be
equivalent in end result, but it is a bug not to support max-frequency
as well.
See: https://github.com/raspberrypi/linux/issues/2350
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
mmc/bcm2835: Recover from MMC_SEND_EXT_CSD
If the user issues an "mmc extcsd read", the SD controller receives
what it thinks is a SEND_IF_COND command with an unexpected data block.
The resulting operations leave the FSM stuck in READWAIT, a state which
persists until the MMC framework resets the controller, by which point
the root filesystem is likely to have been unmounted.
A less heavyweight solution is to detect the condition and nudge the
FSM by asserting the (self-clearing) FORCE_DATA_MODE bit.
N.B. This workaround was essentially discovered by accident and without
a full understanding the inner workings of the controller, so it is
fortunate that the "fix" only modifies error paths.
See: https://github.com/raspberrypi/linux/issues/2728
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-mmc: Fix DMA channel leak
The BCM2835 MMC host driver requests a DMA channel on probe but neglects
to release the channel in the probe error path and on driver unbind.
I'm seeing this happen on every boot of the Compute Module 3: On first
driver probe, DMA channel 2 is allocated and then leaked with a "could
not get clk, deferring probe" message. On second driver probe, channel 4
is allocated.
Fix it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
bcm2835-mmc: Fix struct mmc_host leak on probe
The BCM2835 MMC host driver requests the bus address of the host's
register map on probe. If that fails, the driver leaks the struct
mmc_host allocated earlier.
Fix it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
bcm2835-mmc: Fix duplicate free_irq() on remove
The BCM2835 MMC host driver requests its interrupt as a device-managed
resource, so the interrupt is automatically freed after the driver is
unbound.
However on driver unbind, bcm2835_mmc_remove() frees the interrupt
explicitly to avoid invocation of the interrupt handler after driver
structures have been torn down.
The interrupt is thus freed twice, leading to a WARN splat in
__free_irq(). Fix by not requesting the interrupt as a device-managed
resource.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
bcm2835-mmc: Handle mmc_add_host() errors
The BCM2835 MMC host driver calls mmc_add_host() but doesn't check its
return value. Errors occurring in that function are therefore not
handled. Fix it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
bcm2835-mmc: Deduplicate reset of driver data on remove
The BCM2835 MMC host driver sets the device's driver data pointer to
NULL on ->remove() even though the driver core subsequently does the
same in __device_release_driver(). Drop the duplicate assignment.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
bcm2835_mmc: Remove vestigial threaded IRQ
With SDIO processing now managed by the MMC framework with a
workqueue, the bcm2835_mmc driver no longer needs a threaded
IRQ.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Add missing dma_unmap_sg calls to free relevant swiotlb bounce buffers.
This prevents DMA leaks.
Signed-off-by: Yaroslav Rosomakho <yaroslavros@gmail.com>
Limit max_req_size under arm64 (or any other platform that uses swiotlb) to prevent potential buffer overflow due to bouncing.
Signed-off-by: Yaroslav Rosomakho <yaroslavros@gmail.com>
mmc: sdhci: Silence MMC warnings
When the MMC isn't plugged in, the driver will spam the console which is
pretty annoying when using NFS.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
mmc: sdhci-iproc: Fix vmmc regulators on iProc
The Linux support for controlling card power via regulators appears to
be contentious. I would argue that the default behaviour is contrary to
the SDHCI spec - turning off the power writes a reserved value to the
SD Bus Voltage Select field of the Power Control Register, which
seems to kill the Arasan/iProc controller - but fortunately there is a
hook in sdhci_ops to override the behaviour. Borrow the implementation
from sdhci_arasan_set_power.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-mmc: uninitialized_var is no more
Not all source files which include quirks.h make use of the all of
the available fixup information. When this happens the compiler
complains that some constant variables are defined by never used.
We can fix this by telling the compiler that this intentional by
simply marking them as __maybe_unused.
Fixes the following W=1 kernel build warnings:
In file included from drivers/mmc/core/sdio.c:22:
drivers/mmc/core/quirks.h:105:31: warning: ‘mmc_ext_csd_fixups’ defined but not used [-Wunused-const-variable=]
105 | static const struct mmc_fixup mmc_ext_csd_fixups[] = {
| ^~~~~~~~~~~~~~~~~~
drivers/mmc/core/quirks.h:17:31: warning: ‘mmc_blk_fixups’ defined but not used [-Wunused-const-variable=]
17 | static const struct mmc_fixup mmc_blk_fixups[] = {
| ^~~~~~~~~~~~~~
In file included from drivers/mmc/core/mmc.c:25:
drivers/mmc/core/quirks.h:123:31: warning: ‘sdio_fixup_methods’ defined but not used [-Wunused-const-variable=]
123 | static const struct mmc_fixup sdio_fixup_methods[] = {
| ^~~~~~~~~~~~~~~~~~
drivers/mmc/core/quirks.h:17:31: warning: ‘mmc_blk_fixups’ defined but not used [-Wunused-const-variable=]
17 | static const struct mmc_fixup mmc_blk_fixups[] = {
| ^~~~~~~~~~~~~~
Cc: Andrei Warkentin <andreiw@motorola.com>
Cc: Martin Mares <mj@ucw.cz>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200701124702.908713-2-lee.jones@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Marvell SDIO device ID 0x9134 is used in SDIO Common CIS (Card Information
Structure) and not in SDIO wlan function (with ID 1). SDIO Common CIS is
accessed by function ID 0.
So change this misleading macro name to SDIO_DEVICE_ID_MARVELL_8887_F0 as
it does not refer to wlan function. It refers to function 0.
Wlan module on this SDIO card is available at function ID 1 and is
identified by different SDIO device ID 0x9135. Kernel quirks for SDIO
devices are matched against device ID from SDIO Common CIS. Therefore
device ID used in quirk is correct, just has misleading name.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200522144412.19712-2-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
wl1251 and wl1271 have different vendor id and device id.
So we need to handle both with sdio quirks.
Fixes: 884f386078 ("mmc: core: move some sdio IDs out of quirks file")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Cc: <stable@vger.kernel.org> # v4.11+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch uses limit clock rate quirk to reduce clock rate
for "SDR104" mode on IMX side for Marvell 8887
WiFi + Bluetooth chip side, as Marvell does not recommend
to use SDIO at the speed of higher than 150MHz.
Signed-off-by: Diwakar Sharma <diwakar.sharma@in.bosch.com>
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Certain Micron eMMC v4.5 cards might get broken when HPI feature is used
and hence this patch disables the HPI feature for such buggy cards.
In U-Boot, these cards are reported as
Manufacturer: Micron (ID: 0xFE)
OEM: 0x4E
Name: MMC32G
Revision: 19 (0x13)
Serial: 959241022 Manufact. date: 8/2015 (0x82) CRC: 0x00
Tran Speed: 52000000
Rd Block Len: 512
MMC version 4.5
High Capacity: Yes
Capacity: 29.1 GiB
Boot Partition Size: 16 MiB
Bus Width: 8-bit
According to JEDEC JEP106 manufacturer 0xFE is Numonyx, which was bought by
Micron.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Mark Craske <Mark_Craske@mentor.com>
Cc: <stable@vger.kernel.org> # 4.8+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's not appreciated to place quirks everywhere, let's
put them together just like what we do for USB, PCI etc.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Rename mmc_fixup_methods to sdio_fixup_methods to better
reflect that it's for sdio devices. So we could also pass
on it from sdio card's probe sequence just like what we do
for eMMC and block there.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Rename quirks.c to quirks.h, and include it for
individual C files which need it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
