This reverts commit 2566a89b9e which is
commit a2614140dc upstream.
The above change depends on upstream commit 0faf890fc5 ("net: dsa:
drop rtnl_lock from dsa_slave_switchdev_event_work"), which is not
present in linux-5.15.y. Without that change, waiting for the switchdev
workqueue causes deadlocks on the rtnl_mutex.
Backporting the dependency commit isn't trivial/desirable, since it
requires that the following dependencies of the dependency are also
backported:
df405910ab net: dsa: sja1105: wait for dynamic config command completion on writes too
eb016afd83 net: dsa: sja1105: serialize access to the dynamic config interface
2468346c56 net: mscc: ocelot: serialize access to the MAC table
f7eb4a1c08 net: dsa: b53: serialize access to the ARL table
cf231b436f net: dsa: lantiq_gswip: serialize access to the PCE registers
338a3a4745 net: dsa: introduce locking for the address lists on CPU and DSA ports
and then this bugfix on top:
8940e6b669 ("net: dsa: avoid call to __dev_set_promiscuity() while rtnl_mutex isn't held")
Reported-by: Daniel Suchy <danny@danysek.cz>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bd488afc3b ]
As explained in commits:
74b6d7d133 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3d ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The Seville VSC9959 switch is a platform device, so the initial set of
constraints that I thought would cause this (I2C or SPI buses which call
->remove on ->shutdown) do not apply. But there is one more which
applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the seville switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The seville driver has a code structure that could accommodate both the
mdiobus_unregister and mdiobus_free calls, but it has an external
dependency upon mscc_miim_setup() from mdio-mscc-miim.c, which calls
devm_mdiobus_alloc_size() on its behalf. So rather than restructuring
that, and exporting yet one more symbol mscc_miim_teardown(), let's work
with devres and replace of_mdiobus_register with the devres variant.
When we use all-devres, we can ensure that devres doesn't free a
still-registered bus (it either runs both callbacks, or none).
Fixes: ac3a68d566 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a2614140dc upstream.
mv88e6xxx is special among DSA drivers in that it requires the VTU to
contain the VID of the FDB entry it modifies in
mv88e6xxx_port_db_load_purge(), otherwise it will return -EOPNOTSUPP.
Sometimes due to races this is not always satisfied even if external
code does everything right (first deletes the FDB entries, then the
VLAN), because DSA commits to hardware FDB entries asynchronously since
commit c9eb3e0f87 ("net: dsa: Add support for learning FDB through
notification").
Therefore, the mv88e6xxx driver must close this race condition by
itself, by asking DSA to flush the switchdev workqueue of any FDB
deletions in progress, prior to exiting a VLAN.
Fixes: c9eb3e0f87 ("net: dsa: Add support for learning FDB through notification")
Reported-by: Rafael Richter <rafael.richter@gin.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6bb9681a43 upstream.
The reset input to the LAN9303 chip is active low, and devicetree
gpio handles reflect this. Therefore, the gpio should be requested
with an initial state of high in order for the reset signal to be
asserted. Other uses of the gpio already use the correct polarity.
Fixes: a1292595e0 ("net: dsa: add new DSA switch driver for the SMSC-LAN9303")
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fianelil <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220209145454.19749-1-mans@mansr.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 51a04ebf21 ]
Since struct mv88e6xxx_mdio_bus *mdio_bus is the bus->priv of something
allocated with mdiobus_alloc_size(), this means that mdiobus_free(bus)
will free the memory backing the mdio_bus as well. Therefore, the
mdio_bus->list element is freed memory, but we continue to iterate
through the list of MDIO buses using that list element.
To fix this, use the proper list iterator that handles element deletion
by keeping a copy of the list element next pointer.
Fixes: f53a2ce893 ("net: dsa: mv88e6xxx: don't use devres for mdiobus")
Reported-by: Rafael Richter <rafael.richter@gin.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220210174017.3271099-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d120dfb5d ]
As explained in commits:
74b6d7d133 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3d ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The GSWIP switch is a platform device, so the initial set of constraints
that I thought would cause this (I2C or SPI buses which call ->remove on
->shutdown) do not apply. But there is one more which applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the GSWIP switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The gswip driver has the code structure in place for orderly mdiobus
removal, so just replace devm_mdiobus_alloc() with the non-devres
variant, and add manual free where necessary, to ensure that we don't
let devres free a still-registered bus.
Fixes: ac3a68d566 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ffe3d09e3 ]
Nobody in this driver calls mdiobus_unregister(), which is necessary if
mdiobus_register() completes successfully. So if the devres callbacks
that free the mdiobus get invoked (this is the case when unbinding the
driver), mdiobus_free() will BUG if the mdiobus is still registered,
which it is.
My speculation is that this is due to the fact that prior to commit
ac3a68d566 ("net: phy: don't abuse devres in devm_mdiobus_register()")
from June 2020, _devm_mdiobus_free() used to call mdiobus_unregister().
But at the time that the mt7530 support was introduced in May 2021, the
API was already changed. It's therefore likely that the blamed patch was
developed on an older tree, and incorrectly adapted to net-next. This
makes the Fixes: tag correct.
Fix the problem by using the devres variant of mdiobus_register.
Fixes: ba751e28d4 ("net: dsa: mt7530: add interrupt support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 209bdb7ec6 ]
As explained in commits:
74b6d7d133 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3d ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The Felix VSC9959 switch is a PCI device, so the initial set of
constraints that I thought would cause this (I2C or SPI buses which call
->remove on ->shutdown) do not apply. But there is one more which
applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the felix switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The felix driver has the code structure in place for orderly mdiobus
removal, so just replace devm_mdiobus_alloc_size() with the non-devres
variant, and add manual free where necessary, to ensure that we don't
let devres free a still-registered bus.
Fixes: ac3a68d566 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08f1a20822 ]
As explained in commits:
74b6d7d133 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3d ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The Starfighter 2 is a platform device, so the initial set of
constraints that I thought would cause this (I2C or SPI buses which call
->remove on ->shutdown) do not apply. But there is one more which
applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the bcm_sf2 switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The bcm_sf2 driver has the code structure in place for orderly mdiobus
removal, so just replace devm_mdiobus_alloc() with the non-devres
variant, and add manual free where necessary, to ensure that we don't
let devres free a still-registered bus.
Fixes: ac3a68d566 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50facd86e9 ]
As explained in commits:
74b6d7d133 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3d ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The ar9331 is an MDIO device, so the initial set of constraints that I
thought would cause this (I2C or SPI buses which call ->remove on
->shutdown) do not apply. But there is one more which applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the ar9331 switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The ar9331 driver doesn't have a complex code structure for mdiobus
removal, so just replace of_mdiobus_register with the devres variant in
order to be all-devres and ensure that we don't free a still-registered
bus.
Fixes: ac3a68d566 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f53a2ce893 ]
As explained in commits:
74b6d7d133 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3d ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The mv88e6xxx is an MDIO device, so the initial set of constraints that
I thought would cause this (I2C or SPI buses which call ->remove on
->shutdown) do not apply. But there is one more which applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the Marvell switch driver on shutdown.
systemd-shutdown[1]: Powering off.
mv88e6085 0x0000000008b96000:00 sw_gl0: Link is Down
fsl-mc dpbp.9: Removing from iommu group 7
fsl-mc dpbp.8: Removing from iommu group 7
------------[ cut here ]------------
kernel BUG at drivers/net/phy/mdio_bus.c:677!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 PID: 1 Comm: systemd-shutdow Not tainted 5.16.5-00040-gdc05f73788e5 #15
pc : mdiobus_free+0x44/0x50
lr : devm_mdiobus_free+0x10/0x20
Call trace:
mdiobus_free+0x44/0x50
devm_mdiobus_free+0x10/0x20
devres_release_all+0xa0/0x100
__device_release_driver+0x190/0x220
device_release_driver_internal+0xac/0xb0
device_links_unbind_consumers+0xd4/0x100
__device_release_driver+0x4c/0x220
device_release_driver_internal+0xac/0xb0
device_links_unbind_consumers+0xd4/0x100
__device_release_driver+0x94/0x220
device_release_driver+0x28/0x40
bus_remove_device+0x118/0x124
device_del+0x174/0x420
fsl_mc_device_remove+0x24/0x40
__fsl_mc_device_remove+0xc/0x20
device_for_each_child+0x58/0xa0
dprc_remove+0x90/0xb0
fsl_mc_driver_remove+0x20/0x5c
__device_release_driver+0x21c/0x220
device_release_driver+0x28/0x40
bus_remove_device+0x118/0x124
device_del+0x174/0x420
fsl_mc_bus_remove+0x80/0x100
fsl_mc_bus_shutdown+0xc/0x1c
platform_shutdown+0x20/0x30
device_shutdown+0x154/0x330
kernel_power_off+0x34/0x6c
__do_sys_reboot+0x15c/0x250
__arm64_sys_reboot+0x20/0x30
invoke_syscall.constprop.0+0x4c/0xe0
do_el0_svc+0x4c/0x150
el0_svc+0x24/0xb0
el0t_64_sync_handler+0xa8/0xb0
el0t_64_sync+0x178/0x17c
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The Marvell driver already has a good structure for mdiobus removal, so
just plug in mdiobus_free and get rid of devres.
Fixes: ac3a68d566 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Reported-by: Rafael Richter <Rafael.Richter@gin.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Daniel Klauer <daniel.klauer@gin.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cad1798d2d ]
Allow PTP peer delay measurements on blocked ports by STP. In case of topology
changes the PTP stack can directly start with the correct delays.
Fixes: ddd56dfe52 ("net: dsa: hellcreek: Add PTP clock support")
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b7ade35eb5 ]
Treat STP as management traffic. STP traffic is designated for the CPU port
only. In addition, STP traffic has to pass blocked ports.
Fixes: e4b27ebc78 ("net: dsa: Add DSA driver for Hirschmann Hellcreek switches")
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4db4c3ea56 ]
The insertion of static FDB entries ignores the pass_blocked bit. That bit is
evaluated with regards to STP. Add the missing functionality.
Fixes: e4b27ebc78 ("net: dsa: Add DSA driver for Hirschmann Hellcreek switches")
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e08cdf6304 ]
Debug print uses invalid check to detect if speed is unforced:
(speed != SPEED_UNFORCED) should be used instead of (!speed).
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Andrey Eremeev <Axtone4all@yandex.ru>
Fixes: 96a2b40c7b ("net: dsa: mv88e6xxx: add port's MAC speed setter")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d591fc028 ]
Commit 64d47d50be ("net: dsa: mv88e6xxx: configure interface settings
in mac_config") removed forcing of speed and duplex from
mv88e6xxx_mac_config(), where the link is forced down, and left it only
in mv88e6xxx_mac_link_up(), by which time link is unforced.
It seems that (at least on 88E6190) when changing cmode to 2500base-x,
if the link is not forced down, but the speed or duplex are still
forced, the forcing of new settings for speed & duplex doesn't take in
mv88e6xxx_mac_link_up().
Fix this by unforcing speed & duplex in mv88e6xxx_mac_link_down().
Fixes: 64d47d50be ("net: dsa: mv88e6xxx: configure interface settings in mac_config")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 04ec4e6250 upstream.
Martyn Welch reports that his CPU port is unable to link where it has
been necessary to use one of the switch ports with an internal PHY for
the CPU port. The reason behind this is the port control register is
left forcing the link down, preventing traffic flow.
This occurs because during initialisation, phylink expects the link to
be down, and DSA forces the link down by synthesising a call to the
DSA drivers phylink_mac_link_down() method, but we don't touch the
forced-link state when we later reconfigure the port.
Resolve this by also unforcing the link state when we are operating in
PHY mode and the PPU is set to poll the PHY to retrieve link status
information.
Reported-by: Martyn Welch <martyn.welch@collabora.com>
Tested-by: Martyn Welch <martyn.welch@collabora.com>
Fixes: 3be98b2d5f ("net: dsa: Down cpu/dsa ports phylink will control")
Cc: <stable@vger.kernel.org> # 5.7: 2b29cb9e3f: net: dsa: mv88e6xxx: fix "don't use PHY_DETECT on internal PHY's"
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1mvFhP-00F8Zb-Ul@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b29cb9e3f upstream.
This commit fixes a misunderstanding in commit 4a3e0aeddf ("net: dsa:
mv88e6xxx: don't use PHY_DETECT on internal PHY's").
For Marvell DSA switches with the PHY_DETECT bit (for non-6250 family
devices), controls whether the PPU polls the PHY to retrieve the link,
speed, duplex and pause status to update the port configuration. This
applies for both internal and external PHYs.
For some switches such as 88E6352 and 88E6390X, PHY_DETECT has an
additional function of enabling auto-media mode between the internal
PHY and SERDES blocks depending on which first gains link.
The original intention of commit 5d5b231da7 (net: dsa: mv88e6xxx: use
PHY_DETECT in mac_link_up/mac_link_down) was to allow this bit to be
used to detect when this propagation is enabled, and allow software to
update the port configuration. This has found to be necessary for some
switches which do not automatically propagate status from the SERDES to
the port, which includes the 88E6390. However, commit 4a3e0aeddf
("net: dsa: mv88e6xxx: don't use PHY_DETECT on internal PHY's") breaks
this assumption.
Maarten Zanders has confirmed that the issue he was addressing was for
an 88E6250 switch, which does not have a PHY_DETECT bit in bit 12, but
instead a link status bit. Therefore, mv88e6xxx_port_ppu_updates() does
not report correctly.
This patch resolves the above issues by reverting Maarten's change and
instead making mv88e6xxx_port_ppu_updates() indicate whether the port
is internal for the 88E6250 family of switches.
Yes, you're right, I'm targeting the 6250 family. And yes, your
suggestion would solve my case and is a better implementation for
the other devices (as far as I can see).
Fixes: 4a3e0aeddf ("net: dsa: mv88e6xxx: don't use PHY_DETECT on internal PHY's")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Maarten Zanders <maarten.zanders@mind.be>
Link: https://lore.kernel.org/r/E1muXm7-00EwJB-7n@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 88362ebfd7 upstream.
Currently autoloading for SPI devices does not use the DT ID table, it
uses SPI modalises. Supporting OF modalises is going to be difficult if
not impractical, an attempt was made but has been reverted, so ensure
that module autoloading works for this driver by adding an id_table
listing the SPI IDs for everything.
Fixes: 96c8395e21 ("spi: Revert modalias changes")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ede359d884 upstream.
Function mv88e6xxx_serdes_pcs_get_state() currently does not report link
up if AN is enabled, Link bit is set, but Speed and Duplex Resolved bit
is not set, which testing shows is the case for when auto-negotiation
was bypassed (we have AN enabled but link partner does not).
An example of such link partner is Marvell 88X3310 PHY, when put into
the mode where host interface changes between 10gbase-r, 5gbase-r,
2500base-x and sgmii according to copper speed. The 88X3310 does not
enable AN in 2500base-x, and so SerDes on mv88e6xxx currently does not
link with it.
Fix this.
Fixes: a5a6858b79 ("net: dsa: mv88e6xxx: extend phylink to Serdes PHYs")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 163000dbc7 upstream.
Inband AN is broken on Amethyst in 2500base-x mode when set by standard
mechanism (via cmode).
(There probably is some weird setting done by default in the switch for
this mode that make it cycle in some state or something, because when
the peer is the mvneta controller, it receives link change interrupts
every ~0.3ms, but the link is always down.)
Get around this by configuring the PCS mode to 1000base-x (where inband
AN works), and then changing the SerDes frequency while SerDes
transmitter and receiver are disabled, before enabling SerDes PHY. After
disabling SerDes PHY, change the PCS mode back to 2500base-x, to avoid
confusing the device (if we leave it at 1000base-x PCS mode but with
different frequency, and then change cmode to sgmii, the device won't
change the frequency because it thinks it already has the correct one).
The register which changes the frequency is undocumented. I discovered
it by going through all registers in the ranges 4.f000-4.f100 and
1e.8000-1e.8200 for all SerDes cmodes (sgmii, 1000base-x, 2500base-x,
5gbase-r, 10gbase-r, usxgmii) and filtering out registers that didn't
make sense (the value was the same for modes which have different
frequency). The result of this was:
reg sgmii 1000base-x 2500base-x 5gbase-r 10gbase-r usxgmii
04.f002 005b 0058 0059 005c 005d 005f
04.f076 3000 0000 1000 4000 5000 7000
04.f07c 0950 0950 1850 0550 0150 0150
1e.8000 0059 0059 0058 0055 0051 0051
1e.8140 0e20 0e20 0e28 0e21 0e42 0e42
Register 04.f002 is the documented Port Operational Confiuration
register, it's last 3 bits select PCS type, so changing this register
also changes the frequency to the appropriate value.
Registers 04.f076 and 04.f07c are not writable.
Undocumented register 1e.8000 was the one: changing bits 3:0 from 9 to 8
changed SerDes frequency to 3.125 GHz, while leaving the value of PCS
mode in register 04.f002.2:0 at 1000base-x. Inband autonegotiation
started working correctly.
(I didn't try anything with register 1e.8140 since 1e.8000 solved the
problem.)
Since I don't have documentation for this register 1e.8000.3:0, I am
using the constants without names, but my hypothesis is that this
register selects PHY frequency. If in the future I have access to an
oscilloscope able to handle these frequencies, I will try to test this
hypothesis.
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 93fd8207be upstream.
Add fix for erratum 5.2 of the 88E6393X (Amethyst) family: for 10gbase-r
mode, some undocumented registers need to be written some special
values.
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c3318b487 upstream.
The check for lane is unnecessary, since the function is called only
with allowed lane argument.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 21635d9203 upstream.
According to SERDES scripts for 88E6393X, erratum 4.8 has to be applied
every time before SerDes is powered on.
Split the code for erratum 4.8 into separate function and call it in
mv88e6393x_serdes_power().
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 92f62485b3 ]
Normally it is expected that the dsa_device_ops :: rcv() method finishes
parsing the DSA tag and consumes it, then never looks at it again.
But commit c0bcf53766 ("net: dsa: ocelot: add hardware timestamping
support for Felix") added support for RX timestamping in a very
unconventional way. On this switch, a partial timestamp is available in
the DSA header, but the driver got away with not parsing that timestamp
right away, but instead delayed that parsing for a little longer:
dsa_switch_rcv():
nskb = cpu_dp->rcv(skb, dev); <------------- not here
-> ocelot_rcv()
...
skb = nskb;
skb_push(skb, ETH_HLEN);
skb->pkt_type = PACKET_HOST;
skb->protocol = eth_type_trans(skb, skb->dev);
...
if (dsa_skb_defer_rx_timestamp(p, skb)) <--- but here
-> felix_rxtstamp()
return 0;
When in felix_rxtstamp(), this driver accounted for the fact that
eth_type_trans() happened in the meanwhile, so it got a hold of the
extraction header again by subtracting (ETH_HLEN + OCELOT_TAG_LEN) bytes
from the current skb->data.
This worked for quite some time but was quite fragile from the very
beginning. Not to mention that having DSA tag parsing split in two
different files, under different folders (net/dsa/tag_ocelot.c vs
drivers/net/dsa/ocelot/felix.c) made it quite non-obvious for patches to
come that they might break this.
Finally, the blamed commit does the following: at the end of
ocelot_rcv(), it checks whether the skb payload contains a VLAN header.
If it does, and this port is under a VLAN-aware bridge, that VLAN ID
might not be correct in the sense that the packet might have suffered
VLAN rewriting due to TCAM rules (VCAP IS1). So we consume the VLAN ID
from the skb payload using __skb_vlan_pop(), and take the classified
VLAN ID from the DSA tag, and construct a hwaccel VLAN tag with the
classified VLAN, and the skb payload is VLAN-untagged.
The big problem is that __skb_vlan_pop() does:
memmove(skb->data + VLAN_HLEN, skb->data, 2 * ETH_ALEN);
__skb_pull(skb, VLAN_HLEN);
aka it moves the Ethernet header 4 bytes to the right, and pulls 4 bytes
from the skb headroom (effectively also moving skb->data, by definition).
So for felix_rxtstamp()'s fragile logic, all bets are off now.
Instead of having the "extraction" pointer point to the DSA header,
it actually points to 4 bytes _inside_ the extraction header.
Corollary, the last 4 bytes of the "extraction" header are in fact 4
stale bytes of the destination MAC address from the Ethernet header,
from prior to the __skb_vlan_pop() movement.
So of course, RX timestamps are completely bogus when the system is
configured in this way.
The fix is actually very simple: just don't structure the code like that.
For better or worse, the DSA PTP timestamping API does not offer a
straightforward way for drivers to present their RX timestamps, but
other drivers (sja1105) have established a simple mechanism to carry
their RX timestamp from dsa_device_ops :: rcv() all the way to
dsa_switch_ops :: port_rxtstamp() and even later. That mechanism is to
simply save the partial timestamp to the skb->cb, and complete it later.
Question: why don't we simply populate the skb's struct
skb_shared_hwtstamps from ocelot_rcv(), and bother with this
complication of propagating the timestamp to felix_rxtstamp()?
Answer: dsa_switch_ops :: port_rxtstamp() answers the question whether
PTP packets need sleepable context to retrieve the full RX timestamp.
Currently felix_rxtstamp() answers "no, thanks" to that question, and
calls ocelot_ptp_gettime64() from softirq atomic context. This is
understandable, since Felix VSC9959 is a PCIe memory-mapped switch, so
hardware access does not require sleeping. But the felix driver is
preparing for the introduction of other switches where hardware access
is over a slow bus like SPI or MDIO:
https://lore.kernel.org/lkml/20210814025003.2449143-1-colin.foster@in-advantage.com/
So I would like to keep this code structure, so the rework needed when
that driver will need PTP support will be minimal (answer "yes, I need
deferred context for this skb's RX timestamp", then the partial
timestamp will still be found in the skb->cb.
Fixes: ea440cd2d9 ("net: dsa: tag_ocelot: use VLAN information from tagging header when available")
Reported-by: Po Liu <po.liu@nxp.com>
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f5f12f5d4 ]
The max VLAN number with non-4K VLAN activated is 15, and the
range is 0..15. Not 16.
The impact should be low since we by default have 4K VLAN and
thus have 4095 VLANs to play with in this switch. There will
not be a problem unless the code is rewritten to only use
16 VLANs.
Fixes: d8652956cf ("net: dsa: realtek-smi: Add Realtek SMI driver")
Cc: Mauri Sandberg <sandberg@mailfence.com>
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Setting ds->num_ports to DSA_MAX_PORTS made DSA core allocate unnecessary
dsa_port's and call mt7530_port_disable for non-existent ports.
Set it to MT7530_NUM_PORTS to fix that, and dsa_is_user_port check in
port_enable/disable is no longer required.
Cc: stable@vger.kernel.org
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I compared the register definitions with the D-Link DWR-966
GPL sources and found that the PUAFD field definition was
incorrect. This definition is unused and causes no issues.
Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NXP LS1028A switch has two Ethernet ports towards the CPU, but only
one of them is capable of acting as an NPI port at a time (inject and
extract packets using DSA tags).
However, using the alternative ocelot-8021q tagging protocol, it should
be possible to use both CPU ports symmetrically, but for that we need to
mark both ports in the device tree as DSA masters.
In the process of doing that, it can be seen that traffic to/from the
network stack gets broken, and this is because the Felix driver iterates
through all DSA CPU ports and configures them as NPI ports. But since
there can only be a single NPI port, we effectively end up in a
situation where DSA thinks the default CPU port is the first one, but
the hardware port configured to be an NPI is the last one.
I would like to treat this as a bug, because if the updated device trees
are going to start circulating, it would be really good for existing
kernels to support them, too.
Fixes: adb3dccf09 ("net: dsa: felix: convert to the new .change_tag_protocol DSA API")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
At present, when a PTP packet which requires TX timestamping gets
dropped under congestion by the switch, things go downhill very fast.
The driver keeps a clone of that skb in a queue of packets awaiting TX
timestamp interrupts, but interrupts will never be raised for the
dropped packets.
Moreover, matching timestamped packets to timestamps is done by a 2-bit
timestamp ID, and this can wrap around and we can match on the wrong skb.
Since with the default NPI-based tagging protocol, we get no notification
about packet drops, the best we can do is eventually recover from the
drop of a PTP frame: its skb will be dead memory until another skb which
was assigned the same timestamp ID happens to find it.
However, with the ocelot-8021q tagger which injects packets using the
manual register interface, it appears that we can check for more
information, such as:
- whether the input queue has reached the high watermark or not
- whether the injection group's FIFO can accept additional data or not
so we know that a PTP frame is likely to get dropped before actually
sending it, and drop it ourselves (because DSA uses NETIF_F_LLTX, so it
can't return NETDEV_TX_BUSY to ask the qdisc to requeue the packet).
But when we do that, we can also remove the skb from the timestamping
queue, because there surely won't be any timestamp that matches it.
Fixes: 0a6f17c6ae ("net: dsa: tag_ocelot_8021q: add support for PTP timestamping")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Michael reported that when using the "ocelot-8021q" tagging protocol,
the switch driver module must be manually loaded before the tagging
protocol can be loaded/is available.
This appears to be the same problem described here:
https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/
where due to the fact that DSA tagging protocols make use of symbols
exported by the switch drivers, circular dependencies appear and this
breaks module autoloading.
The ocelot_8021q driver needs the ocelot_can_inject() and
ocelot_port_inject_frame() functions from the switch library. Previously
the wrong approach was taken to solve that dependency: shims were
provided for the case where the ocelot switch library was compiled out,
but that turns out to be insufficient, because the dependency when the
switch lib _is_ compiled is problematic too.
We cannot declare ocelot_can_inject() and ocelot_port_inject_frame() as
static inline functions, because these access I/O functions like
__ocelot_write_ix() which is called by ocelot_write_rix(). Making those
static inline basically means exposing the whole guts of the ocelot
switch library, not ideal...
We already have one tagging protocol driver which calls into the switch
driver during xmit but not using any exported symbol: sja1105_defer_xmit.
We can do the same thing here: create a kthread worker and one work item
per skb, and let the switch driver itself do the register accesses to
send the skb, and then consume it.
Fixes: 0a6f17c6ae ("net: dsa: tag_ocelot_8021q: add support for PTP timestamping")
Reported-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
PTP packets with 2-step TX timestamp requests are matched to packets
based on the egress port number and a 6-bit timestamp identifier.
All PTP timestamps are held in a common FIFO that is 128 entry deep.
This patch ensures that back-to-back timestamping requests cannot exceed
the hardware FIFO capacity. If that happens, simply send the packets
without requesting a TX timestamp to be taken (in the case of felix,
since the DSA API has a void return code in ds->ops->port_txtstamp) or
drop them (in the case of ocelot).
I've moved the ts_id_lock from a per-port basis to a per-switch basis,
because we need separate accounting for both numbers of PTP frames in
flight. And since we need locking to inc/dec the per-switch counter,
that also offers protection for the per-port counter and hence there is
no reason to have a per-port counter anymore.
Fixes: 4e3b0468e6 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It's nice to be able to test a tagging protocol with dsa_loop, but not
at the cost of losing the ability of building the tagging protocol and
switch driver as modules, because as things stand, there is a circular
dependency between the two. Tagging protocol drivers cannot depend on
switch drivers, that is a hard fact.
The reasoning behind the blamed patch was that accessing dp->priv should
first make sure that the structure behind that pointer is what we really
think it is.
Currently the "sja1105" and "sja1110" tagging protocols only operate
with the sja1105 switch driver, just like any other tagging protocol and
switch combination. The only way to mix and match them is by modifying
the code, and this applies to dsa_loop as well (by default that uses
DSA_TAG_PROTO_NONE). So while in principle there is an issue, in
practice there isn't one.
Until we extend dsa_loop to allow user space configuration, treat the
problem as a non-issue and just say that DSA ports found by tag_sja1105
are always sja1105 ports, which is in fact true. But keep the
dsa_port_is_sja1105 function so that it's easy to patch it during
testing, and rely on dead code elimination.
Fixes: 994d2cbb08 ("net: dsa: tag_sja1105: be dsa_loop-safe")
Link: https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The problem is that DSA tagging protocols really must not depend on the
switch driver, because this creates a circular dependency at insmod
time, and the switch driver will effectively not load when the tagging
protocol driver is missing.
The code was structured in the way it was for a reason, though. The DSA
driver-facing API for PTP timestamping relies on the assumption that
two-step TX timestamps are provided by the hardware in an out-of-band
manner, typically by raising an interrupt and making that timestamp
available inside some sort of FIFO which is to be accessed over
SPI/MDIO/etc.
So the API puts .port_txtstamp into dsa_switch_ops, because it is
expected that the switch driver needs to save some state (like put the
skb into a queue until its TX timestamp arrives).
On SJA1110, TX timestamps are provided by the switch as Ethernet
packets, so this makes them be received and processed by the tagging
protocol driver. This in itself is great, because the timestamps are
full 64-bit and do not require reconstruction, and since Ethernet is the
fastest I/O method available to/from the switch, PTP timestamps arrive
very quickly, no matter how bottlenecked the SPI connection is, because
SPI interaction is not needed at all.
DSA's code structure and strict isolation between the tagging protocol
driver and the switch driver break the natural code organization.
When the tagging protocol driver receives a packet which is classified
as a metadata packet containing timestamps, it passes those timestamps
one by one to the switch driver, which then proceeds to compare them
based on the recorded timestamp ID that was generated in .port_txtstamp.
The communication between the tagging protocol and the switch driver is
done through a method exported by the switch driver, sja1110_process_meta_tstamp.
To satisfy build requirements, we force a dependency to build the
tagging protocol driver as a module when the switch driver is a module.
However, as explained in the first paragraph, that causes the circular
dependency.
To solve this, move the skb queue from struct sja1105_private :: struct
sja1105_ptp_data to struct sja1105_private :: struct sja1105_tagger_data.
The latter is a data structure for which hacks have already been put
into place to be able to create persistent storage per switch that is
accessible from the tagging protocol driver (see sja1105_setup_ports).
With the skb queue directly accessible from the tagging protocol driver,
we can now move sja1110_process_meta_tstamp into the tagging driver
itself, and avoid exporting a symbol.
Fixes: 566b18c8b7 ("net: dsa: sja1105: implement TX timestamping for SJA1110")
Link: https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the ksz module is installed and removed using rmmod, kernel crashes
with null pointer dereferrence error. During rmmod, ksz_switch_remove
function tries to cancel the mib_read_workqueue using
cancel_delayed_work_sync routine and unregister switch from dsa.
During dsa_unregister_switch it calls ksz_mac_link_down, which in turn
reschedules the workqueue since mib_interval is non-zero.
Due to which queue executed after mib_interval and it tries to access
dp->slave. But the slave is unregistered in the ksz_switch_remove
function. Hence kernel crashes.
To avoid this crash, before canceling the workqueue, resetted the
mib_interval to 0.
v1 -> v2:
-Removed the if condition in ksz_mib_read_work
Fixes: 469b390e1b ("net: dsa: microchip: use delayed_work instead of timer + work")
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx_port_ppu_updates() interpretes data in the PORT_STS
register incorrectly for internal ports (ie no PPU). In these
cases, the PHY_DETECT bit indicates link status. This results
in forcing the MAC state whenever the PHY link goes down which
is not intended. As a side effect, LED's configured to show
link status stay lit even though the physical link is down.
Add a check in mac_link_down and mac_link_up to see if it
concerns an external port and only then, look at PPU status.
Fixes: 5d5b231da7 (net: dsa: mv88e6xxx: use PHY_DETECT in mac_link_up/mac_link_down)
Reported-by: Maarten Zanders <m.zanders@televic.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Maarten Zanders <maarten.zanders@mind.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to commit 6087175b79 ("net: dsa: mt7530: use independent VLAN
learning on VLAN-unaware bridges"), software forwarding between an
unoffloaded LAG port (a bonding interface with an unsupported policy)
and a mv88e6xxx user port directly under a bridge is broken.
We adopt the same strategy, which is to make the standalone ports not
find any ATU entry learned on a bridge port.
Theory: the mv88e6xxx ATU is looked up by FID and MAC address. There are
as many FIDs as VIDs (4096). The FID is derived from the VID when
possible (the VTU maps a VID to a FID), with a fallback to the port
based default FID value when not (802.1Q Mode is disabled on the port,
or the classified VID isn't present in the VTU).
The mv88e6xxx driver makes the following use of FIDs and VIDs:
- the port's DefaultVID (to which untagged & pvid-tagged packets get
classified) is 0 and is absent from the VTU, so this kind of packets is
processed in FID 0, the default FID assigned by mv88e6xxx_setup_port.
- every time a bridge VLAN is created, mv88e6xxx_port_vlan_join() ->
mv88e6xxx_atu_new() associates a FID with that VID which increases
linearly starting from 1. Like this:
bridge vlan add dev lan0 vid 100 # FID 1
bridge vlan add dev lan1 vid 100 # still FID 1
bridge vlan add dev lan2 vid 1024 # FID 2
The FID allocation made by the driver is sub-optimal for the following
reasons:
(a) A standalone port has a DefaultPVID of 0 and a default FID of 0 too.
A VLAN-unaware bridged port has a DefaultPVID of 0 and a default FID
of 0 too. The difference is that the bridged ports may learn ATU
entries, while the standalone port has the requirement that it must
not, and must not find them either. Standalone ports must not use
the same FID as ports belonging to a bridge. All standalone ports
can use the same FID, since the ATU will never have an entry in
that FID.
(b) Multiple VLAN-unaware bridges will all use a DefaultPVID of 0 and a
default FID of 0 on all their ports. The FDBs will not be isolated
between these bridges. Every VLAN-unaware bridge must use the same
FID on all its ports, different from the FID of other bridge ports.
(c) Each bridge VLAN uses a unique FID which is useful for Independent
VLAN Learning, but the same VLAN ID on multiple VLAN-aware bridges
will result in the same FID being used by mv88e6xxx_atu_new().
The correct behavior is for VLAN 1 in br0 to have a different FID
compared to VLAN 1 in br1.
This patch cannot fix all the above. Traditionally the DSA framework did
not care about this, and the reality is that DSA core involvement is
needed for the aforementioned issues to be solved. The only thing we can
solve here is an issue which does not require API changes, and that is
issue (a), aka use a different FID for standalone ports vs ports under
VLAN-unaware bridges.
The first step is deciding what VID and FID to use for standalone ports,
and what VID and FID for bridged ports. The 0/0 pair for standalone
ports is what they used up till now, let's keep using that. For bridged
ports, there are 2 cases:
- VLAN-aware ports will never end up using the port default FID, because
packets will always be classified to a VID in the VTU or dropped
otherwise. The FID is the one associated with the VID in the VTU.
- On VLAN-unaware ports, we _could_ leave their DefaultVID (pvid) at
zero (just as in the case of standalone ports), and just change the
port's default FID from 0 to a different number (say 1).
However, Tobias points out that there is one more requirement to cater to:
cross-chip bridging. The Marvell DSA header does not carry the FID in
it, only the VID. So once a packet crosses a DSA link, if it has a VID
of zero it will get classified to the default FID of that cascade port.
Relying on a port default FID for upstream cascade ports results in
contradictions: a default FID of 0 breaks ATU isolation of bridged ports
on the downstream switch, a default FID of 1 breaks standalone ports on
the downstream switch.
So not only must standalone ports have different FIDs compared to
bridged ports, they must also have different DefaultVID values.
IEEE 802.1Q defines two reserved VID values: 0 and 4095. So we simply
choose 4095 as the DefaultVID of ports belonging to VLAN-unaware
bridges, and VID 4095 maps to FID 1.
For the xmit operation to look up the same ATU database, we need to put
VID 4095 in DSA tags sent to ports belonging to VLAN-unaware bridges
too. All shared ports are configured to map this VID to the bridging
FID, because they are members of that VLAN in the VTU. Shared ports
don't need to have 802.1QMode enabled in any way, they always parse the
VID from the DSA header, they don't need to look at the 802.1Q header.
We install VID 4095 to the VTU in mv88e6xxx_setup_port(), with the
mention that mv88e6xxx_vtu_setup() which was located right below that
call was flushing the VTU so those entries wouldn't be preserved.
So we need to relocate the VTU flushing prior to the port initialization
during ->setup(). Also note that this is why it is safe to assume that
VID 4095 will get associated with FID 1: the user ports haven't been
created, so there is no avenue for the user to create a bridge VLAN
which could otherwise race with the creation of another FID which would
otherwise use up the non-reserved FID value of 1.
[ Currently mv88e6xxx_port_vlan_join() doesn't have the option of
specifying a preferred FID, it always calls mv88e6xxx_atu_new(). ]
mv88e6xxx_port_db_load_purge() is the function to access the ATU for
FDB/MDB entries, and it used to determine the FID to use for
VLAN-unaware FDB entries (VID=0) using mv88e6xxx_port_get_fid().
But the driver only called mv88e6xxx_port_set_fid() once, during probe,
so no surprises, the port FID was always 0, the call to get_fid() was
redundant. As much as I would have wanted to not touch that code, the
logic is broken when we add a new FID which is not the port-based
default. Now the port-based default FID only corresponds to standalone
ports, and FDB/MDB entries belong to the bridging service. So while in
the future, when the DSA API will support FDB isolation, we will have to
figure out the FID based on the bridge number, for now there's a single
bridging FID, so hardcode that.
Lastly, the tagger needs to check, when it is transmitting a VLAN
untagged skb, whether it is sending it towards a bridged or a standalone
port. When we see it is bridged we assume the bridge is VLAN-unaware.
Not because it cannot be VLAN-aware but:
- if we are transmitting from a VLAN-aware bridge we are likely doing so
using TX forwarding offload. That code path guarantees that skbs have
a vlan hwaccel tag in them, so we would not enter the "else" branch
of the "if (skb->protocol == htons(ETH_P_8021Q))" condition.
- if we are transmitting on behalf of a VLAN-aware bridge but with no TX
forwarding offload (no PVT support, out of space in the PVT, whatever),
we would indeed be transmitting with VLAN 4095 instead of the bridge
device's pvid. However we would be injecting a "From CPU" frame, and
the switch won't learn from that - it only learns from "Forward" frames.
So it is inconsequential for address learning. And VLAN 4095 is
absolutely enough for the frame to exit the switch, since we never
remove that VLAN from any port.
Fixes: 57e661aae6 ("net: dsa: mv88e6xxx: Link aggregation support")
Reported-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The VLAN support in mv88e6xxx has a loaded history. Commit 2ea7a679ca
("net: dsa: Don't add vlans when vlan filtering is disabled") noticed
some issues with VLAN and decided the best way to deal with them was to
make the DSA core ignore VLANs added by the bridge while VLAN awareness
is turned off. Those issues were never explained, just presented as
"at least one corner case".
That approach had problems of its own, presented by
commit 54a0ed0df4 ("net: dsa: provide an option for drivers to always
receive bridge VLANs") for the DSA core, followed by
commit 1fb7419198 ("net: dsa: mv88e6xxx: fix vlan setup") which
applied ds->configure_vlan_while_not_filtering = true for mv88e6xxx in
particular.
We still don't know what corner case Andrew saw when he wrote
commit 2ea7a679ca ("net: dsa: Don't add vlans when vlan filtering is
disabled"), but Tobias now reports that when we use TX forwarding
offload, pinging an external station from the bridge device is broken if
the front-facing DSA user port has flooding turned off. The full
description is in the link below, but for short, when a mv88e6xxx port
is under a VLAN-unaware bridge, it inherits that bridge's pvid.
So packets ingressing a user port will be classified to e.g. VID 1
(assuming that value for the bridge_default_pvid), whereas when
tag_dsa.c xmits towards a user port, it always sends packets using a VID
of 0 if that port is standalone or under a VLAN-unaware bridge - or at
least it did so prior to commit d82f8ab0d8 ("net: dsa: tag_dsa:
offload the bridge forwarding process").
In any case, when there is a conversation between the CPU and a station
connected to a user port, the station's MAC address is learned in VID 1
but the CPU tries to transmit through VID 0. The packets reach the
intended station, but via flooding and not by virtue of matching the
existing ATU entry.
DSA has established (and enforced in other drivers: sja1105, felix,
mt7530) that a VLAN-unaware port should use a private pvid, and not
inherit the one from the bridge. The bridge's pvid should only be
inherited when that bridge is VLAN-aware, so all state transitions need
to be handled. On the other hand, all bridge VLANs should sit in the VTU
starting with the moment when the bridge offloads them via switchdev,
they are just not used.
This solves the problem that Tobias sees because packets ingressing on
VLAN-unaware user ports now get classified to VID 0, which is also the
VID used by tag_dsa.c on xmit.
Fixes: d82f8ab0d8 ("net: dsa: tag_dsa: offload the bridge forwarding process")
Link: https://patchwork.kernel.org/project/netdevbpf/patch/20211003222312.284175-2-vladimir.oltean@nxp.com/#24491503
Reported-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Same members of the Marvell Ethernet switches impose MTU restrictions
on ports used for connecting to the CPU or another switch for DSA. If
the MTU is set too low, tagged frames will be discarded. Ensure the
worst case tagger overhead is included in setting the MTU for DSA and
CPU ports.
Fixes: 1baf0fac10 ("net: dsa: mv88e6xxx: Use chip-wide max frame size for MTU")
Reported by: 曹煜 <cao88yu@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
