As there isn't currently a defined mechanism for selecting an
external trigger mode on image sensors, copy the imx477
approach of using a module parameter to enable ext trig.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Whilst the adv7180 driver support s_routing, nothing else
does, and there is a missing lump of framework code to
define the mapping from connectors on a board to the inputs
they represent on the ADV7180.
Add a nasty hack to take a module parameter that is passed in
to s_routing on any call to G_STD, or S_STD (or subdev
g_input_status call).
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
There is no obligation for all source devices on a video-mux to
require the same bus configuration, so read the configuration
from the sink ports, and relay via get_mbus_config on the source
port.
If the sources support get_mbus_config, then call that first.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The BCM54213PE identifier is a RPI-specific addition.
Populate the remainder of the driver functions, including the
required probe routine.
Add a version of bcm54xx_suspend, from upstream.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Also check for which HDMI devices are connected and only create
devices for those that are present.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
snd_bcm2835: disable HDMI audio when vc4 is used (#3640)
Things don't work too well when both the vc4 driver and the firmware
driver are trying to control the same audio output:
[ 763.569406] bcm2835_audio bcm2835_audio: vchi message timeout, msg=5
Hence, when the vc4 HDMI driver is used, let it control audio. This is done
by introducing a new device tree property to the audio node, and
extending the vc4-kms-v3d overlays to set it appropriately.
Signed-off-by: Hristo Venev <hristo@venev.name>
staging: bcm2835-audio: Add disable-headphones flag
Add a property to allow the headphone output to be disabled. Use an
integer property rather than a boolean so that an overlay can clear it.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
staging: bcm2835-audio: Find compatible firmware node
Commit "ARM: dts: Adopt the upstream snd_bcm2835 handling" removed the
audio section from the DT and the driver can no longer access the
referenced firmware node 'brcm,firmware'. Fix that by searching for a
compatible firmware node instead, similar to drivers/gpu/drm/vc4.
Fixes: b9e62329e096 ("ARM: dts: Adopt the upstream snd_bcm2835 handling")
Signed-off-by: Juerg Haefliger <juergh@proton.me>
staging: bcm2835-audio: Fix firmware node refcounting
Decrement firmware node refcounts on all exit paths in set_hdmi_enables().
Signed-off-by: Juerg Haefliger <juergh@proton.me>
staging: bcm2835-audio: Log errors in case of firmware query failures
The driver queries the firmware for the number of detected HDMI displays
and their IDs. Log error messages if queries fail.
Signed-off-by: Juerg Haefliger <juergh@proton.me>
staging: bcm2835-audio: Fix unused enable_hdmi module parameter
The commit "Add HDMI1 facility to the driver." made the enable_hdmi module
parameter unused. Fix that by making it a global switch for all available
HDMI audio outputs.
Fixes: 755f336608 ("Add HDMI1 facility to the driver.")
Signed-off-by: Juerg Haefliger <juergh@proton.me>
staging: bcm2835-audio: Fix unused enable_headphones module parameter
Since commit "staging: bcm2835-audio: Add disable-headphones flag" the
enabling/disabling of the headphones output is solely determined by the
presence of the DT property 'brcm,disable-headphones' and the
enable_headphones module parameter is unused. Fix that by making it a
global switch.
Fixes: ee90e47d88 ("staging: bcm2835-audio: Add disable-headphones flag")
Signed-off-by: Juerg Haefliger <juergh@proton.me>
Add a driver for the Arducam 64MP camera sensor.
Whilst the sensor supports 2 or 4 CSI2 data lanes, this driver
currently only supports 2 lanes.
The following Bayer modes are currently available:
9152x6944 10-bit @ 2.7fps
4624x3472 10-bit (binned) @ 10fps
3840x2160 10-bit (cropped/binned) @ 20fps
2312x1736 10-bit (binned) @ 30fps
1920x1080 10-bit (cropped/binned) @ 60fps
1280x720 10-bit (cropped/binned) @ 120fps
Signed-off-by: Lee Jackson <info@arducam.com>
media: i2c: arducam_64mp: Advertise embedded data node on media pad 1
This commit updates the arducam_64mp driver to adverise support for
embedded data streams.
The arducam_64mp sensor subdevice overloads the media pad to differentiate
between image stream (pad 0) and embedded data stream (pad 1) when
performing the v4l2_subdev_pad_ops functions.
Signed-off-by: Lee Jackson <info@arducam.com>
media: i2c: arducam_64mp: Modify the line length of 1280x720 resolution
Arducam 64MP has specific requirements for the line length, and if these
conditions are not met, the camera will not function properly. Under the
previous configuration, once a stream off operation is performed, the
camera will not output any data, even if a stream on operation is
performed. This prevents us from switching from 1280x720 to another
resolution.
Signed-off-by: Lee Jackson <lee.jackson@arducam.com>
media: i2c: arducam_64mp: Add 8000x6000 resolution
Added 8000x6000 10-bit (cropped) @ 3fps mode for Arducam 64MP
Signed-off-by: Lee Jackson <lee.jackson@arducam.com>
media: i2c: arducam_64mp: Add PDAF support
Enable PDAF output for all modes, and also need to modify Embedded Line
Width to 11560 * 3 (two lines of Embedded Data + one line of PDAF).
Signed-off-by: Lee Jackson <lee.jackson@arducam.com>
drivers: media: arducam_64mp: Add V4L2_CID_LINK_FREQ control
Add V4L2_CID_LINK_FREQ as a read-only control with a value of 456 Mhz.
This will be used by the CFE driver to corretly setup the DPHY timing
parameters in the CSI-2 block.
Signed-off-by: Lee Jackson <lee.jackson@arducam.com>
[ I would like to pursue fixing this more directly first before actually
merging this, but I thought I'd send this to the list now anyway as a
the "backup" plan. If I can't figure out how to make headway on the
main plan in the next few days, it'll be easy to just do this. ]
Stephen reported that a static key warning splat appears during early
boot on systems that credit randomness from device trees that contain an
"rng-seed" property, because because setup_machine_fdt() is called
before jump_label_init() during setup_arch():
static_key_enable_cpuslocked(): static key '0xffffffe51c6fcfc0' used before call to jump_label_init()
WARNING: CPU: 0 PID: 0 at kernel/jump_label.c:166 static_key_enable_cpuslocked+0xb0/0xb8
Modules linked in:
CPU: 0 PID: 0 Comm: swapper Not tainted 5.18.0+ #224 44b43e377bfc84bc99bb5ab885ff694984ee09ff
pstate: 600001c9 (nZCv dAIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : static_key_enable_cpuslocked+0xb0/0xb8
lr : static_key_enable_cpuslocked+0xb0/0xb8
sp : ffffffe51c393cf0
x29: ffffffe51c393cf0 x28: 000000008185054c x27: 00000000f1042f10
x26: 0000000000000000 x25: 00000000f10302b2 x24: 0000002513200000
x23: 0000002513200000 x22: ffffffe51c1c9000 x21: fffffffdfdc00000
x20: ffffffe51c2f0831 x19: ffffffe51c6fcfc0 x18: 00000000ffff1020
x17: 00000000e1e2ac90 x16: 00000000000000e0 x15: ffffffe51b710708
x14: 0000000000000066 x13: 0000000000000018 x12: 0000000000000000
x11: 0000000000000000 x10: 00000000ffffffff x9 : 0000000000000000
x8 : 0000000000000000 x7 : 61632065726f6665 x6 : 6220646573752027
x5 : ffffffe51c641d25 x4 : ffffffe51c13142c x3 : ffff0a00ffffff05
x2 : 40000000ffffe003 x1 : 00000000000001c0 x0 : 0000000000000065
Call trace:
static_key_enable_cpuslocked+0xb0/0xb8
static_key_enable+0x2c/0x40
crng_set_ready+0x24/0x30
execute_in_process_context+0x80/0x90
_credit_init_bits+0x100/0x154
add_bootloader_randomness+0x64/0x78
early_init_dt_scan_chosen+0x140/0x184
early_init_dt_scan_nodes+0x28/0x4c
early_init_dt_scan+0x40/0x44
setup_machine_fdt+0x7c/0x120
setup_arch+0x74/0x1d8
start_kernel+0x84/0x44c
__primary_switched+0xc0/0xc8
---[ end trace 0000000000000000 ]---
random: crng init done
Machine model: Google Lazor (rev1 - 2) with LTE
A trivial fix went in to address this on arm64, 73e2d827a5 ("arm64:
Initialize jump labels before setup_machine_fdt()"). But it appears that
fixing it on other platforms might not be so trivial. Instead, defer the
setting of the static branch until later in the boot process.
Fixes: f5bda35fba ("random: use static branch for crng_ready()")
Reported-by: Stephen Boyd <swboyd@chromium.org>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
The driver had a number of issues, checkpatch warnings/errors,
and other limitations, so fix these up to make it usable.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
hwmon: emc2305: Add calls to initialise of cooling maps
Commit 46ef9d4ed2 ("hwmon: emc2305: fixups for driver submitted to
mailing lists") missed adding the call to thermal_of_cooling_device_register
required to configure any cooling maps for the device, hence stopping it
from actually ever changing speed.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
hwmon: emc2305: Change OF properties pwm-min & pwm-max to u8
There is no DT binding for emc2305 as mainline are still
discussing how to do a generic fan binding.
The 5.15 driver was reading the "emc2305," properties
"cooling-levels", "pwm-max", "pwm-min", and "pwm-channel" as u8.
The overlay was writing them as u16 (;) so it was working.
The 6.1 driver was reading as u32, which failed as there is
insufficient data.
As this is all downstream only, revert to u8 to match 5.15.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
It is quite common for the devm_thermal_zone_of_sensor_register
to need to defer, so avoid spamming the log by using
dev_err_probe instead of dev_err.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Add a driver for the Arducam Pivariety series CSI2 camera sensor.
Signed-off-by: Lee Jackson <info@arducam.com>
SQUASH: Fix VIDEO_ARDUCAM_PIVARIETY Kconfig entry
The cherry-pick from rpi-5.17.y put it in the wrong section, and failed
to update it for 5.18.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
media: i2c: arducam-pivariety: Add custom controls
Add support for strobe_shift, strobe_width and mode custom controls.
Signed-off-by: Lee Jackson <info@arducam.com>
media: i2c: arducam-pivariety: Fix mutex init and NULL pointer
The mutex used in arducam-pivariety was not properly initialized,
which could lead to undefined behavior. This also caused a NULL
pointer dereference under certain conditions.
This patch ensures the mutex is correctly initialized during probe
and prevents NULL pointer dereferences.
Signed-off-by: Yuriy Pasichnyk <yurijpasichnyk11@gmail.com>
Add YAML device tree binding for Arducam Pivariety CMOS image sensor, and
the relevant MAINTAINERS entries.
Signed-off-by: Lee Jackson <info@arducam.com>
On some platforms the cma area can be half the entire system memory,
meaning that allocations start happening in the cma area immediately.
This leads to fragmentation and subsequent fatal cma_alloc failures.
We introduce an "alloc_in_cma_threshold" parameter which requires that
this many sixteenths of the free pages must be in cma before it will
try to use them. By default this is set to 12, but the previous
behaviour can be restored by setting it to 8 on startup.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Adds a driver for the Analog Devices AD5398 10 bit
I2C DAC which is commonly used for driving VCM lens
mechanisms.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: i2c: Rename ad5398 to ad5398_vcm
There's already a regulator module called ad5398 that exposes
this device through the regulator API. That is meaningless in
the terms that it uses and how it maps to V4L2, so a new driver
was added. However the module name collision wasn't noted, so
rename it now.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Add a binding for Analog Devices AD5398 10bit current
sinking DAC when used as a lens VCM driver.
FIXME: Convert to YAML
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Omnivision OV2311 is a CSI2 1600x1300 global shutter image sensor.
Add a driver for it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: i2c: Update ov2311 Kconfig entry
Bring the OV2311 Kconfig declaration in line with upstream entries.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
media: i2c: ov2311: Fix uninitialized variable usage
Signed-off-by: Alexander Winkowski <dereference23@outlook.com>
"media: i2c: Remove .s_power() from ov7251" removed the call that
sent ov7251_global_init_setting to the sensor. Send it when starting
streaming.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The sck-idle-input property indicates that the spi-gpio driver should
return the SCK line to an input when the chip select signals are
inactive.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
https://github.com/raspberrypi/linux/issues/4440
Upstream has added additional device specific controls, so the
V4L2_CID_USER_BASE + 0x10e0 value that had been defined for use with
the ISP has been taken by something else (and +0x10f0 has been used as
well)
Duplicate the use on V4L2_CID_USER_BASE + 0x10e0 so that userspace
(libcamera) doesn't need to change. Once the driver is upstream, then
we'll update libcamera to adopt the new value as it then won't change.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Not all implementations wire up the enable GPIO and may just tie
it to a supply rail.
Make it optional.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The I2C to the Atmel is very fussy, and locks up easily on
Pi0-3 particularly on reads.
The LCD power status is controlled solely by this driver, so
rather than reading it back from the Atmel, use the cached
status last set.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
regulator/rpi-panel: Power off display on shutdown
Adds a shutdown function to turn off the backlight, bridge, and
touch controller on shutdown.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
regulator/rpi-panel: Remove the ID read
Reading from the Atmel has always been troublesome due to
clock stretching, and the driver does nothing with it anyway.
Remove the read and assume that if the overlay has been
configured (most likely through the firmware autodetection)
that the hardware is present.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
As happens occasionally, an upstream change has once again prevented
spidev from being loaded via Device Tree. We now need "spidev" to be
included in the new spi_device_id list, otherwise although the
spidev driver gets loaded no /dev/spidev*.* entries will appear.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
An unwanted side effect of enabling the BRCMDBG config setting is
redefining brcmf_info to be brcmf_err. This can be alarming to users
and makes it harder to spot real errors, so don't do it.
See: https://github.com/raspberrypi/linux/issues/4663
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
For cases where spare PWM outputs are available, but are desired
to be addressed a standard outputs instead.
Wraps a PWM channel as a new GPIO chip with the one output.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
pwm: gpio-pwm: follow pwm_apply_might_sleep() rename
Fixes: 03286093be68("drivers/gpio: Add a driver that wraps the PWM API as a GPIO controller")
Signed-off-by: Ratchanan Srirattanamet <peathot@hotmail.com>
Some platforms include a fan-speed register that reports RPM directly
as an alternative to counting interrupts from the fan tachometer input.
Add support for reading a register at a given offset (rpm-offset) within
a block declared in another node (rpm-regmap). This indirection allows
the usual address mapping to be performed, and for address sharing with
another driver.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Should we go through the timeout failure case with port_disable
not returning all buffers for whatever reason, the
buffers_with_vpu counter gets left at a non-zero value, which
will cause reference counting issues should the instance be
reused.
Reset the count when the port is enabled again, but before
any buffers have been sent to the VPU.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The firmware can only use I2C0 if the kernel isn't, therefore
with libcamera and DRM using it the PoE HAT fan control needs
to move to the kernel.
Add the option for the driver to be created by the PoE HAT core
MFD driver, and use the I2C regmap that provides to control fan
functions.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The Raspbery Pi PoE+ HAT exposes a fan controller and power
supply status reporting via a single I2C address.
Create an MFD device that allows loading of the relevant
sub-drivers, with a shared I2C regmap.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Serge Schneider <serge@raspberrypi.com>
power: rpi-poe: Drop CURRENT_AVG as it is not hardware averaged
As documented the _AVG parameters are meant to be hardware
averaged, but the implementation for the PoE+ HAT was done in
software in the firmware.
Drop the property.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
power: rpi-poe: Add option of being created by MFD or FW
The firmware can only use I2C0 if the kernel isn't, therefore
with libcamera and DRM using it the PoE HAT fan control needs
to move to the kernel.
Add the option for the driver to be created by the PoE HAT core
MFD driver, and use the I2C regmap that provides to control fan
functions.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
power: rpi-poe: FIXUP DRIVER.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
As we're wanting to wrap the image_fx component for deinterlacing,
add the deinterlace algorithm values to enum mmal_parameter_imagefx
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Adds enum mmal_interlace_type and struct
mmal_parameter_video_interlace_type to allow for querying the
interlacing mode on decoders.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Bindings for the panel-dsi specific additions to panel-simple.
Allow for DSI specific bus settings and panel timing
to be define in devicetree. Very similar to panel-dpi.
Signed-off-by: Timon Skerutsch <kernel@diodes-delight.com>
The Geekworm MZP280 panel is a 480x640 (portrait) panel with a
capacitive touch interface and a 40 pin header meant to interface
directly with the Raspberry Pi. The screen is 2.8 inches diagonally,
and there appear to be at least 4 distinct versions all with the same
panel timings.
Timings were derived from drivers posted on the github located here:
https://github.com/tianyoujian/MZDPI/tree/master/vga
Additional details about this panel family can be found here:
https://wiki.geekworm.com/2.8_inch_Touch_Screen_for_Pi_zero
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
The regulator of the Waveshare DSI-TOUCH series panels is different.
Add a new driver for this regulator.
Signed-off-by: Waveshare_Team <support@waveshare.com>
drivers/regulator : Adjust power enable sequence
Avoid direct enabling of LCD power here.
Certain screens require immediate initialization after power-on
to prevent polarization.
Signed-off-by: Waveshare_Team <support@waveshare.com>
Waveshare sell a range of DSI panels of varying sizes, all
using a common MCU to control the panel and backlight.
Add a panel driver that supports these panels.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm/panel: waveshare: Fix up timings for 10.1" panel
The 10.1" panel doesn't work with the timings defined. vc4
will always have been fixing up the timing due to the limited
integer divider, so compute the fixed up mode and use it
directly.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drivers/gpu/drm/panel:fix waveshare panel software restart/shutdown display is abnormal
Fixed the screen stays white when the user restarts or shuts down
Signed-off-by: eng33 <eng33@waveshare.com>
drivers/gpu/drm/panel:Modify the DSI mode to fix the problem that 7.9inch cannot be displayed
Signed-off-by: eng33 <eng33@waveshare.com>
drivers/gpu/drm/panel:Modified the timing of 11.9inch to fix the issue that 11.9inch was displayed abnormally
Signed-off-by: eng33 <eng33@waveshare.com>
Driver:add waveshare 4inch dsi lcd (C) driver
Signed-off-by: Eng33 <eng33@waveshare.net>
drivers:gpu:drm:panel: Added waveshare 5.0inch, 6.25inch, and 8.8inch dsi screen devices
Signed-off-by: eng33 <eng33@waveshare.com>
drm: panel: Added waveshare 13.3inch panel
Signed-off-by: eng33 <eng33@waveshare.com>
drm: panel: Added waveshare 7.0inch h dsi screen support
Signed-off-by: Waveshare_Team <support@waveshare.com>
drivers/gpu/drm/panel : Add the device for the Waveshare DSI-TOUCH series panels.
the driver are provided for the Waveshare DSI-TOUCH series panels,
modelled after the other Ilitek controller drivers,
but not limited to Ilitek series controllers.
The aim is to offer a more consistent operation and
experience for the Waveshare DSI-TOUCH series panels.
Signed-off-by: Waveshare_Team <support@waveshare.com>
drivers/gpu/drm/panel : Update display driver
1) Add LCD power control
2) Added support for:
A) Add support for 3.4-DSI-TOUCH-C
B) Add support for 4-DSI-TOUCH-C
C) Add support for 8-DSI-TOUCH-A
D) Add support for 9-DSI-TOUCH-B
E) Add support for 10.1-DSI-TOUCH-B
F) Add support for 12.3-DSI-TOUCH-A
Signed-off-by: Waveshare_Team <support@waveshare.com>
The Top DisplayOptoelectronics (TDO) T17B driver chip is used
in the TL040HDS20CT panel (found in the Pimoroni HyperPixel4
Square display) and potentially other displays.
The driver chip supports SPI for configuration and DPI
video data.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
This new panel uses the ILI9881C IC but needs an alternate
init sequence, and therefore requires a new compatible string.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Penk Chen <penk@cutiepi.io>
drm/panel: ilitek-ili9881c: Clean up on mipi_dsi_attach failure
mipi_dsi_attach is allowed to fail, and currently the probe
code doesn't clean up (mainly drm_panel_remove) if this happens.
Add cleanup code on failure.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm/panel: panel-ilitek9881c: Use cansleep methods
Use cansleep version of gpiod_set_value so external IO drivers (like
via I2C) can be used.
Signed-off-by: Mark Williams <mwp@mwp.id.au>
drm/panel: panel-ilitek9881c: Crystalfontz support
Add support for Crystalfontz CFAF7201280A0-050Tx panel.
Signed-off-by: Mark Williams <mwp@mwp.id.au>
drm/panel: ili9881: Add configuration for the new panels
Add configuration for the 5" and 7" Raspberry Pi 720x1280
DSI panels based on ili9881.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Update panel-ilitek-ili9881c.c
Correcting display dimension typo
ILI9881C: Update timings for CFAF7201280A0-050TX
Update of ILI9881C CFAF7201280A0-050TX panel timing to work with the CM5.
Signed-off-by: Mark Williams <mark@crystalfontz.com>
There is no reason why the control GPIOs for the panel can not
be connected to I2C or similar GPIO interfaces that may need to
sleep, therefore switch from gpiod_set_value to
gpiod_set_value_cansleep calls to configure them.
Without that you get complaints from gpiolib every time the state
is changed.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm: panel: jdi-lt070me05000: Add prepare_upstream_first flag
The panel driver wants to send DCS commands from the prepare
hook, therefore the DSI host wants to be pre_enabled first.
Set the flag to achieve this.
https://forums.raspberrypi.com/viewtopic.php?t=354708
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The Raspberry Pi 7" 800x480 panel uses a Toshiba TC358762 DSI
to DPI bridge chip, so there is a requirement for the timings
to be specified for the end panel. Add such a definition.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm/panel-simple: Populate bpc when using panel-dpi
panel-dpi doesn't know the bit depth, so in the same way that
DPI is guessed for the connector type, guess that it'll be 8bpc.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm/panel-simple: Allow the bus format to be read from DT for panel-dpi
The "panel-dpi" compatible string configures panel from device tree,
but it doesn't provide any way of configuring the bus format (colour
representation), nor does it populate it.
Add a DT parameter "bus-format" that allows the MEDIA_BUS_FMT_xxx value
to be specified from device tree.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm/panel: simple: add Geekworm MZP280 Panel
Add support for the Geekworm MZP280 Panel
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Maxime Ripard <maxime@cerno.tech>
drm/panel: simple: Add Innolux AT056tN53V1 5.6" VGA
Add support for the Innolux AT056tN53V1 5.6" VGA (640x480) TFT LCD
panel.
Signed-off-by: Joerg Quinten <aBUGSworstnightmare@gmail.com>
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
drm/panel: simple: Alter the timing for the Pi 7" DSI display
vc4 has always fixed up the timing, so the values defined have
never actually appeared on the wire.
The display appears to want a slightly longer HFP, so extend
the timings and recompute the clock to give the same frame rate.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm/panel: add panel-dsi
Equivalent to panel-dpi for configuring a simple DSI panel with
device tree side timings and bus settings.
Motiviation is the same as for panel-dpi of wanting to support
new simple panels without needing to patch the kernel.
Signed-off-by: Timon Skerutsch <kernel@diodes-delight.com>
drm/panel-simple: Remove custom handling of orientation
The framework now handles reading orientation from DT, therefore
remove the custom get_orientation hook from panel-simple.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm/panel-simple: Fix 7inch panel mode for misalignment
The 7inch panel is one line off the screen both horizontally
and vertically.
Alter the panel mode to correct this.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm/panel-simple: Increase pixel clock on Pi 7inch panel
The Toshiba bridge is very fussy and doesn't like the CM3
output when being told to produce a 27.777MHz pixel clock, which
is an almost perfect match to the DSI link integer divider.
Increasing to 30MHz will switch the DSI link from 333MHz to 400MHz
and makes the bridge happy with the same video timing as works
on Pi4.
(Pi4 will be using a link frequency of 375MHz due to a 3GHz
parent PLL).
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
We now have the hardware I2C controller pinmuxed to the drive the
display I2C, but this controller does not support clock stretching.
The Atmel micro-controller in the panel requires clock stretching
to allow it to prepare any data to be read.
Split the rpi_touchscreen_i2c_read into two independent transactions with
a delay between them for the Atmel to prepare the data.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm/panel/raspberrypi-ts: Insert delay before polling for startup state
In switching to the hardware I2C controller there is an issue
where we seem to not get back the correct state from the Pi
touchscreen.
Insert a delay before polling to avoid this condition.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm/panel/raspberrypi-touchscreen: Handle I2C errors.
rpi_touchscreen_i2c_read returns any errors from i2c_transfer,
or the 8 bit received value.
Check for error values before trying to process the data as
valid.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm/panel/raspberrypi-touchscreen: Insert more delays.
This avoids failures in cases where the panel is enabled
or re-probed very soon after being disabled or probed.
These can occur because the Atmel device can mis-behave
over I2C for a few ms after any write to the POWERON register.
