Pull "pxa-dt for v4.13" from Robert Jarzmik:
This device-tree pxa update brings :
- cpu operating points renaming from Viresh
* tag 'pxa-dt-4.13' of https://github.com/rjarzmik/linux:
ARM: pxa: Use - instead of @ for DT OPP entries
Pull "Samsung DeviceTree update for v4.13, part two" from Krzysztof Kozłowski:
1. Add needed property for CEC on Odroid U3,
2. Fix reset GPIO polarity on Rinato.
* tag 'samsung-dt-4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Fix polarity of panel reset gpio in Rinato
ARM: dts: exynos: add needs-hpd to &hdmicec for Odroid-U3
Compiling the DT file with W=1, DTC warns like follows:
Warning (unit_address_vs_reg): Node /opp_table0/opp@1000000000 has a
unit name, but no reg property
Fix this by replacing '@' with '-' as the OPP nodes will never have a
"reg" property.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
The i.MX device tree updates for 4.13:
- New board support: Gateworks Ventana GW5600, Technexion Pico i.MX7D
Board.
- A series from Alexandre Belloni to correct the vendor prefix for
rv4162 compatible.
- A patch-set from Andrey Smirnov ot enable PCIe support for i.MX7 and
imx7d-sdb board.
- Increase the SGTL5000 LRCLK pad strength to fix a random audio
channel swapping seen on imx6qdl-wandboard and imx6qdl-colibri
boards.
- Clean up non-existing property 'enable-active-low' from fixed
regulator device nodes.
- Correct GPIO polarity for Ethernet PHY and PCI reset lines, even
though device drivers do not use the polarity for now.
- Add Wifi and Bluetooth support for imx7d-sdb board.
- Adopt the i.MX6Q/DL DT to the new and more flexible GPC binding.
- Update zii-rdu2 device tree source to use #include "..." for local
inclusion.
- A series from Philipp Zabel and Steve Longerbeam to enable video
capture support for imx6qdl platforms.
- A number of small random updates on various board support.
* tag 'imx-dt-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (47 commits)
ARM: dts: imx6q-cm-fx6: add sdio wifi/bt nodes
ARM: dts: ls1021a: update the clockgen node
ARM: dts: imx6-sabreauto: add the ADV7180 video decoder
ARM: dts: imx6-sabreauto: add pinctrl for gpt input capture
ARM: dts: imx6-sabreauto: add reset-gpios property for max7310_b
ARM: dts: imx6-sabreauto: create i2cmux for i2c3
ARM: dts: imx6-sabresd: add OV5642 and OV5640 camera sensors
ARM: dts: imx6-sabrelite: add OV5642 and OV5640 camera sensors
ARM: dts: imx6qdl-sabrelite: remove erratum ERR006687 workaround
ARM: dts: imx6qdl: add capture-subsystem device
ARM: dts: imx6qdl: Add video multiplexers, mipi_csi, and their connections
ARM: dts: imx6qdl: Add compatible, clocks, irqs to MIPI CSI-2 node
ARM: dts: imx6qdl: add multiplexer controls
ARM: dts: imx6: Fix PCI GPIO reset polarity
ARM: dts: imx7d-sdb: Add Bluetooth support
ARM: dts: imx7d-sdb: Add Wifi support
ARM: dts: imx7d-sdb: Adjust the regulator nodes
ARM: dts: imx: Fix Ethernet PHY reset polarity
ARM: dts: imx7: Fix typo in watchdog pin name
ARM: dts: vf610-zii: Add switch eeprom-length properties
...
Signed-off-by: Olof Johansson <olof@lixom.net>
mvebu dt for 4.13 (part 1)
- Add Linksys WRT3200ACM (Rango) support
- Add PWM properties for gpio on Aramda XP and 38x
- A couple of minor updates for the 98dx3236 and 98dx4251
* tag 'mvebu-dt-4.13-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: turris-omnia: Add generic compatible string for I2C EEPROM
ARM: dts: mvebu: add support for Linksys WRT3200ACM (Rango)
ARM: dts: armada-385-linksys: fixup button node names
ARM: dts: armada-385-linksys: group pins in pinctrl
ARM: dts: armada-385-linksys: partition layout is board specific
ARM: dts: armada-385-linksys: use binary unit prefixes
ARM: dts: armada-385-linksys: drop legacy DSA bindings
ARM: dts: armada-385-linksys: usb3 label cleanup
ARM: dts: armada-385-linksys: bm pools by label order
ARM: dts: armada-385-linksys: drop redundant properties in dependants
ARM: dts: armada-385-linksys: flatten dependants
ARM: dts: armada-385-linksys: label nodes
ARM: dts: armada-385-linksys: flatten dtsi
ARM: dts: mvebu: disable the rtc on 98dx3236 SoC
ARM: dts: mvebu: add missing interrupt to 98dx4251 switch
ARM: dts: armada-xp: Use pwm-fan rather than gpio-fan
ARM: dts: mvebu: Add PWM properties for armada-38x
ARM: dts: mvebu: Add PWM properties to .dtsi files
Signed-off-by: Olof Johansson <olof@lixom.net>
DT for 4.13
- Switch to the new NAND binding
- A few non urgent fixes
* tag 'at91-ab-4.13-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: dts: at91: sama5d2_xplained: remove wrong memory node
ARM: dts: at91: sama5d2_xplained: add pwm controller
ARM: dts: at91: Add the NOR flash available on sama5d3 dev kits
ARM: dts: at91: Switch to the new NAND bindings
ARM: dts: at91: Declare EBI/NAND controllers
dt-bindings: mtd: atmel-nand: Document the nfc-io bindings
ARM: dts: at91-sama5d4: use IRQ_TYPE_* to specify irq flags
dts: gpio_atmel: adapt binding doc to reality
ARM: dts: at91: sama5d2: add m_can nodes
ARM: dts: at91: Add generic compatible string for I2C EEPROM
Signed-off-by: Olof Johansson <olof@lixom.net>
Second Round of Renesas ARM Based SoC DT Updates for v4.13
Cleanup:
* Correct PCI bus dtc warnings for r8a779x SoCs
Enhancements:
* Add support for iWave G20D-Q7 board based on RZ/G1M SoC
* Add support for GR-Peach board based on r7s72100 SoC
* Add composite video and HDMI input to gose board
* tag 'renesas-dt2-for-v4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: dts: r8a779x: Fix PCI bus dtc warnings
ARM: dts: iwg20d-q7: Add support for iWave G20D-Q7 board based on RZ/G1M
ARM: dts: iwg20m: Add iWave RZG1M Qseven SOM
ARM: dts: gose: add composite video input
ARM: dts: r7s72100: Add support for GR-Peach
ARM: dts: gose: add HDMI input
Signed-off-by: Olof Johansson <olof@lixom.net>
Qualcomm Device Tree Changes for v4.13
* Fix IPQ4019 i2c0 node
* Add GSBI7 on IPQ8064
* Add misc APQ8060 devices
* Fixup USB related devices on APQ8064 and MSM8974
* tag 'qcom-dts-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
ARM: dts: add core I2C devices to the APQ8060 Dragonboard
ARM: dts: add GSBI8 defines to the MSM8660 family
ARM: dts: Qualcomm APQ8060 DragonBoard ALS sensor
ARM: dts: add XOADC and IIO HWMON to MSM8660/APQ8060
ARM: dts: qcom: ipq4019: fix i2c_0 node
ARM: dts: qcom: add gsbi7 serial to ipq8064 SoC device tree
ARM: dts: qcom-apq8064: Collapse usb support into one node
ARM: dts: qcom-msm8974: Add HS usb node and OTG detection mechanisms
ARM: dts: qcom: add charger otg regulator
ARM: dts: qcom: Remove s4/5vs1,2 from RPM pm8941 control
Signed-off-by: Olof Johansson <olof@lixom.net>
ARM: tegra: Device tree changes for v4.13-rc1
This removes support for the Whistler board, which only a handful of
people ever had access to and which doesn't provide any features over
other Tegra20 devices that we support.
Also this cleans up some PCI related device tree content in preparation
for a future DTC release that has additional checks for the PCI bus.
* tag 'tegra-for-4.13-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: dts: tegra: fix PCI bus dtc warnings
ARM: tegra: remove Whistler support
Signed-off-by: Olof Johansson <olof@lixom.net>
Allwinner H3 changes for 4.13
This tag is about bringing the EMAC support to the H3 boards.
* tag 'sunxi-dt-h3-for-4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: sun8i: h3: Enable EMAC with external PHY on Orange Pi Plus 2E
arm: sun8i: orangepi-zero: Enable dwmac-sun8i
ARM: sun8i: bananapi-m2-plus: Enable dwmac-sun8i
ARM: sun8i: orangepi-plus: Enable dwmac-sun8i
arm: sun8i: nanopi-neo: Enable dwmac-sun8i
arm: sun8i: orangepi-pc-plus: Set EMAC activity LEDs to active high
arm: sun8i: orangepi-2: Enable dwmac-sun8i
arm: sun8i: orangepi-one: Enable dwmac-sun8i
arm: sun8i: orangepi-pc: Enable dwmac-sun8i
arm: sun8i: sunxi-h3-h5: add dwmac-sun8i ethernet driver
arm: sun8i: sunxi-h3-h5: Add dt node for the syscon control module
ARM: sunxi: h3-h5: Convert R_CCU raw numbers to macros
Signed-off-by: Olof Johansson <olof@lixom.net>
Allwinner DT changes for 4.13
The usual chunk of patches. The most notable improvements are the power
supplies improvements (battery and AC-IN), crypto support for the sun5i
family, HDMI support for the A10s, plus a lot of new things for the V3S and
the A83T.
* tag 'sunxi-dt-for-4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (47 commits)
ARM: sun6i: a31s: primo81: Enable battery power supply
ARM: sun6i: a31s: primo81: Change USB OTG to OTG mode
ARM: sun8i: a83t: Add dt node for the syscon control module
ARM: sun8i: a83t: Add device node for R_PIO
ARM: sun8i: v3s: add device nodes for DE2 display pipeline
ARM: dts: sunxi: add SoC specific compatibles for the crypto nodes
ARM: sun5i: add a cryptographic engine node
ARM: sun8i: a83t: Add device node for PRCM
ARM: dts: sun8i: h3: Add initial NanoPi M1 Plus support
ARM: dts: orange-pi-zero: add node for SPI NOR
ARM: sun7i: a20: cubietruck: Tie AXP209's USB power supply to USB PHY
ARM: sun6i: a31: hummingbird: Enable AXP221's ACIN power supply
ARM: sun4i: a10: cubieboard: Enable AXP209's ACIN power supply
ARM: sun7i: a20: bananapi-m1-plus: Enable AXP209's ACIN power supply
ARM: sun7i: a20: cubieboard2: Enable AXP209's ACIN power supply
ARM: sun7i: a20: cubieboard2: Move usb_otg node for alphabetical ordering
ARM: sun8i: a83t: cubietruck-plus: Enable SPDIF output
ARM: sun8i: a83t: cubietruck-plus: Add LED device nodes
ARM: sun8i: a83t: Add device node for SPDIF transmitter
ARM: sun8i: a83t: Add device node for DMA controller
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Amlogic 32-bit DT changes for v4.13:
- minor reorganization to support different busses
- add/use real clock controller
* tag 'amlogic-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM: dts: meson8: add and use the real clock controller
ARM: dts: meson: Extend L2 cache controller node for Meson8 and Meson8b
ARM: dts: meson8b: inherit meson.dtsi from meson8b.dtsi
ARM: dts: meson: organize devices in their corresponding busses
Signed-off-by: Olof Johansson <olof@lixom.net>
Gemini DTS patches for v4.13, take 2:
- Add DMA controller
- Add PATA controller and SATA bridge
* tag 'gemini-v4.13-dts-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: add Gemini PATA/SATA support
ARM: dts: Add Gemini DMA controller
Signed-off-by: Olof Johansson <olof@lixom.net>
This pull request contains Broadcom ARM-based Device Tree changes for 4.13.
Note that Baruch's changes are fixes that are currently included in v4.12-rc2,
but they are also included here in order to keep this tag based off v4.12-rc1.
Please pull the following:
- Rafal adds CPU and thermal zones to the Northstar (BCM5301X) Device Tree and he
also adds the MDIO controller nodes for later use by USB PHYs
- Eric adds support for the V3D engine and Ethernet switch on the Cygnus
platforms, he also adds a set of Device Tree sources and include files for the
Raspberry Pi 3 (BCM2837) to be used with the ARM/Linux kernel,
- Jon adds CPU and thermal zones to the Northstar Plus Device Tree files
- Stefan updates the Raspberry Pi DTS files with thermal trip points and zones,
adds support for the USB OTG on the Raspberry Pi Zero which includes the
proper dwc2 configuration, a generic USB PHY and finally the enabling of the
OTG controller by including the proper DTS include file
- Gerd switches the Raspberry Pi DTS files to use the SDHOST controller (faster
than the SDHCI)
* tag 'arm-soc/for-4.13/devicetree' of http://github.com/Broadcom/stblinux:
ARM: dts: bcm2835-rpi-zero: Enable OTG mode
ARM: dts: bcm283x: Add generic USB PHY
ARM: dts: bcm283x: Add dtsi for OTG mode
ARM: dts: Cygnus: Add the ethernet switch and ethernet PHY
ARM: dts: NSP: Add Thermal Support
ARM: dts: Cygnus: Add BCM11360's V3D device
ARM: dts: BCM5301X: Specify MDIO bus in the DT
ARM: dts: BCM5301X: Add CPU thermal sensor and zone
ARM: dts: bcm283x: switch from &sdhci to &sdhost
ARM: dts: bcm283x: Add CPU thermal zone with 1 trip point
ARM: dts: Add devicetree for the Raspberry Pi 3, for arm32 (v6)
Signed-off-by: Olof Johansson <olof@lixom.net>
UniPhier ARM SoC DT updates for v4.13
- fix W=1 build warnings
- use SPDX License Identifier
- add generic compatible string for I2C EEPROM
* tag 'uniphier-dt-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
ARM: dts: uniphier: Add generic compatible string for I2C EEPROM
ARM: dts: uniphier: use SPDX-License-Identifier
ARM: dts: uniphier: fix simple-bus unit address format error
ARM: dts: uniphier: Use - instead of @ for DT OPP entries
Signed-off-by: Olof Johansson <olof@lixom.net>
ARM: dts: Keystone K2G ICE EVM support for v4.13
* tag 'keystone_dts_for_4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
ARM: dts: keystone: Add minimum support for K2G ICE evm
ARM: keystone: Create new binding for K2G ICE evm
ARM: dts: k2g-evm: Add unit address to memory node
ARM: dts: keystone-k2g: Remove skeleton.dtsi
Signed-off-by: Olof Johansson <olof@lixom.net>
Samsung DeviceTree update for v4.13:
1. Add HDMI CEC to Exynos5 SoCs.
2. Minor cleanups and readability improvements.
* tag 'samsung-dt-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Use human-friendly symbols for GIC interrupt properties
ARM: dts: exynos: Use human-friendly symbols for interrupt flags in board sources
ARM: dts: exynos: Add HDMI CEC device to Exynos5 SoC family
ARM: dts: exynos: Remove MFC reserved buffers
Signed-off-by: Olof Johansson <olof@lixom.net>
A bunch of changes including mali gpu nodes for rk3288 boards
following (and including) the new Mali Midgard binding; a lot of
improvements for the rk3228/rk3229 socs (tsadc, operating points,
usb, clock-rates, pinctrl, watchdog); finalizing the rk1108->rv1108
rename and adc buttons for the rk3288 firefly boards.
* tag 'v4.13-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: enable usb for rk3229 evb board
ARM: dts: rockchip: add usb nodes on rk322x
ARM: dts: rockchip: add adc button for Firefly
ARM: dts: rockchip: enable ARM Mali GPU on rk3288-veyron
ARM: dts: rockchip: enable ARM Mali GPU on rk3288-firefly
ARM: dts: rockchip: enable ARM Mali GPU on rk3288-rock2-som
ARM: dts: rockchip: add ARM Mali GPU node for rk3288
dt-bindings: gpu: add bindings for the ARM Mali Midgard GPU
ARM: dts: rockchip: set a sane frequence for tsadc on rk322x
ARM: dts: rockchip: add operating-points-v2 for cpu on rk322x
ARM: dts: rockchip: set default rates for core clocks on rk322x
ARM: dts: rockchip: add second uart2 pinctrl on rk322x
ARM: dts: rockchip: correct rk322x uart2 pinctrl
ARM: dts: rockchip: add watchdog device node on rk322x
clk: rockchip: add clock-ids for more rk3228 clocks
clk: rockchip: add ids for camera on rk3399
ARM: dts: rockchip: fix rk322x i2s1 pinctrl error
ARM: dts: rockchip: rename RK1108-evb to RV1108-evb
ARM: dts: rockchip: rename core dtsi from RK1108 to RV1108
ARM: dts: rockchip: Setup usb vbus-supply on rk3288-rock2
Signed-off-by: Olof Johansson <olof@lixom.net>
Miscellaneous DT support updates for DA850. Includes Lego mindstorms
EV3 battery support, DMA support for MUSB, and non-critical fixes to
GPIO nodes of DA850's GPIO controller and GPIO expander available on
DA850 EVM.
* tag 'davinci-for-v4.13/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850-evm: fix tca6416 for use with GPIO hogs
ARM: dts: da850: Add interrupt-controller property to gpio node
ARM: dts: da850: Add CPPI 4.1 DMA to USB OTG controller
ARM: dts: da850-lego-ev3: Add node for LEGO MINDSTORMS EV3 Battery
Signed-off-by: Olof Johansson <olof@lixom.net>
Device tree changes for omaps for v4.13 merge window.
This adds support for am335x-boneblue. The rest of
the changes are for enabling features on various
devices with the git shortlog describing the changes.
* tag 'omap-for-v4.13/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
arm: dts: am33xx: Remove redundant interrupt-parent property
ARM: dts: bonegreen-wireless: add WL1835 Bluetooth device node
ARM: dts: AM43XX: Remove min and max voltage values for dcdc3
ARM: dts: Add am335x-boneblue
ARM: dts: twl4030: Add missing madc reference for bci subnode
ARM: dts: am43xx-clocks: Add support for CLKOUT2
ARM: dts: Configure USB host for 37xx-evm
ARM: dts: omap: Add generic compatible string for I2C EEPROM
ARM: dts: Enable earlycon stdout path for LogicPD torpedo
ARM: dts: Enable earlycon stdout path for duovero
arm: dts: boneblack-wireless: add WL1835 Bluetooth device node
ARM: dts: am571x-idk: Enable the system mailboxes 5 and 6
ARM: dts: am572x-idk: Enable the system mailboxes 5 and 6
ARM: dts: omap4-devkit8000: fix gpmc ranges property
ARM: dts: omap3: Remove 'enable-active-low' property
ARM: dts: OMAP5: uevm: add µSD card detect
ARM: dts: omap4-droid4: Add bluetooth
ARM: dts: dra7x-evm: Enable dual-role mode for USB1
ARM: dts: Use - instead of @ for DT OPP entries for TI SoCs
ARM: dts: am335x-phycore-som: fix rv4162 compatible
Signed-off-by: Olof Johansson <olof@lixom.net>
The cm-fx6 module has an on-board AW-NH387 WiFi/BT module which is
based on Marvell's SD8787 chip and is connected to the usdhc1
controller.
Unfortunately, the chip gets unresponsive if the Bluetooth AMP
(Alternate Mac/Phy) function gets probed but the loaded firmware
doesn't support it. For instance, this is the case for the most
recent firmware in linux-firmware (Version 14.66.35.p52).
Thus, just add the required nodes but leave the usdhc1 node disabled
explicitly. Users who disabled the Bluetooth (AMP) support of their
OS can then conveniently enable WiFi (or even plain Bluetooth) support
with a simple device tree overlay/bootloader configuration.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Linksys WRT3200ACM (Rango) is the lates Armada-385 based router in
the Linksys WRT AC Series which got released in October 2016.
Key differences to the earlier Armada-385 based devices in the series is
a bigger flash chip, next generation wireless modules (Marvell 88W8964)
in the mini pcie slots as well as a Marvell SD8887. Finally the CPU is
clocked at 1866 GHz by default.
The file armada-385-linksys-rango.dts is loosly based off of a DTS
authored by Imre Kaloz.
As Rango is part of the armada-385-linksys family of boards use the
armada-385-linksys.dtsi as basis. As for functional differences to Imre
Kaloz dts, the wlan LEDs aren't connected to the expander chip pca9635
but directly to GPIOs. Then mpp47 controls the USB2.0 port and not the
USB3.0 port, so use the correct GPIO mpp44 for it. Finally use
non-removable instead of broken-cd with the sdhci node to avoid polling.
Other changes can be categorized as just cleanup / reorganization due to
using the armada-385-linksys.dtsi.
URL: 0abc3fa5a9/target/linux/mvebu/files/arch/arm/boot/dts/armada-385-linksys-rango.dts
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Buttons don't have a reg property; drop pseudo address and fixup names
of individual button nodes. Also drop #address-cells and #size-cells
properties.
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
A pin group per node is sufficient, further specialization only serves
as documentation which can be a comment just as well. This simplifies
configuring pins for nodes in dependants.
Also use labels which end up right by the node they are intended for.
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Now that we use the reference for the USB3.0 port update the node name
and labels for the phy and vbus to match the label used by
armada-38x.dtsi.
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Flatten dts of individual boards to match the new style used in
armada-385-linksys.dtsi and for the Rango addition.
* Caiman - Linksys WRT1200AC v1 & v2
* Cobra - Linksys WRT1900AC v2
* Shelby - Linksys WRT1900ACS v1 & v2
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add labels to nodes used by dependants. Also rename node gpio_keys to
gpio-keys to match the style of the rest of the file as well as the
documented example.
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Since the addition of the spi reference two styles are used. Use
references instead of recreating the same structure over and over again.
This helps to distinguish which are changes to the underlying nodes and
which are new additions and helps maintainability in general.
Verified the resulting dtb to be binary identical.
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This reset gpio is active low, therefore fix from active high to low.
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The Odroid-U3 board has an IP4791CZ12 level shifter that is
disabled if the HPD is low, which means that the CEC pin is
disabled as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
qoriq clock driver has been updated to parse the clock configuration
information defined in driver itself not in dts.
Since the new implementation and the bindings have been merged,
it is time to update the clock related node and remove redundent clock
configuration information from the dts.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The MSI Primo81 tablet has a 3500 mAh 3.7V LiPo battery.
Enable the PMIC's battery power supply so the battery can be monitored.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we have support for the AXP221 PMIC's USB VBUS detection and
DRIVEVBUS vbus control, we can use the USB OTG port in proper OTG mode.
This patch enables the aforementioned PMIC functions, adds the OTG ID
detection pin to the USB PHY node, and changes the mode of USB OTG to
"otg".
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enables the ADV7180 decoder sensor. The ADV7180 connects to the
parallel-bus mux input on ipu1_csi0_mux.
The ADV7180 power pin is via max7310_b port expander.
Changes from Tim Harvey:
- Use IRQ_TYPE_LEVEL_LOW instead of 0x8 for interrupt type for clarity.
- For 8-bit parallel IPU1-CSI0 bus connection only data[12-19] are used.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
