commit b1d2e4e03f upstream.
Fixup the checksum for CHECKSUM_COMPLETE when pulling skbs on RX path.
Otherwise we get splats when tc mirred is used to redirect packets to ifb.
Before fix:
nic: hw csum failure
Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The format change from S24_LE to S24_3LE effectively disables 24-bit
mode as S24_3LE isn't supported by bcm2835-i2s. This causes issues
with drivers that want to use wm8804 in 24-bit mode.
Adding the S32_LE format is also incorrect, according to the datasheet
only 16-24 bit formats are supported.
Signed-off-by: Matthias Reichl <hias@horus.com>
Commit <eea52743eb5654ec6f52b0e8b4aefec952543697> upstream
Fixes: <b3e3893e1253> ("net: use core MTU range checking")
which patched only one of two functions used to setup the
USB Gadget Ethernet driver, causing a serious performance
regression in the ability to increase mtu size above 1500.
Signed-off-by: John Greb <h3x4m3r0n@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The SC16IS752 has an Enhanced Feature Register which is aliased at the
same address as the Interrupt Identification Register; accessing it
requires that a magic value is written to the Line Configuration
Register. If an interrupt is raised while the EFR is mapped in then
the ISR won't be able to access the IIR, leading to the "Unexpected
interrupt" error messages.
Avoid the problem by claiming a mutex around accesses to the EFR
register, also claiming the mutex in the interrupt handler work
item (this is equivalent to disabling interrupts to interlock against
a non-threaded interrupt handler).
See: https://github.com/raspberrypi/linux/issues/2529
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
It has been observed that a Pi with no SD card will poll the interface
continuously, using up to 10% CPU. Add some new parameters to the
sdtweak overlay to control this behaviour:
poll_once Only look for a card once, at boot time. If none is found
then the interface is effectively disabled.
enable Set to "off" or "no" to completely disable the interface.
See: https://github.com/raspberrypi/linux/issues/2567
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
WM8804 can run with PLL frequencies of 256xfs and 128xfs for most sample
rates. At 192kHz only 128xfs is supported. The existing driver selects
128xfs automatically for some lower samples rates. By using an
additional mclk_div divider, it is now possible to control the
behaviour. This allows using 256xfs PLL frequency on all sample rates up
to 96kHz. It should allow lower jitter and better signal quality. The
behavior has to be controlled by the sound card driver, because some
sample frequency share the same setting. e.g. 192kHz and 96kHz use
24.576MHz master clock. The only difference is the MCLK divider.
This also added support for 32bit data.
Signed-off-by: Daniel Matuschek <daniel@matuschek.net>
The published API to the dynamic overlay application mechanism now
takes a Flattened Device Tree blob as input so that it can manage the
lifetime of the unflattened tree. Conveniently, the new API call -
of_overlay_fdt_apply - is virtually a drop-in replacement for
create_overlay, which can now be deleted.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
ad83c7cb2f ("irqchip/irq-bcm2836: Add support for DT interrupt polarity")
changed the way that the BCM2836/7 local interrupts are mapped; instead
of being pre-mapped they are now mapped on-demand. A side effect of this
change is that the call to irq_of_parse_and_map from armctrl_of_init
creates a new mapping, forming a gap between the IRQs and the FIQs. This
gap breaks the FIQ<->IRQ mapping which up to now has been done by assuming:
1) that the value of FIQ_START is the same as the number of normal IRQs
that will be mapped (still true), and
2) that this value is also the offset between an IRQ and its equivalent
FIQ (which is no longer the case).
Remove both assumptions by measuring the interval between the last IRQ
and the last FIQ, passing it as the parameter to init_FIQ().
Fixes: https://github.com/raspberrypi/linux/issues/2432
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Register for reboot notifications, sending RPI_FIRMWARE_NOTIFY_REBOOT
over the mailbox interface on reception.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Upstream Linux deems using output GPIOs to generate IRQs as a bogus
use case, even though the BCM2835 GPIO controller is capable of doing
so. A number of users would like to make use of this facility, so
disable the checks.
See: https://github.com/raspberrypi/linux/issues/2527
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
With HW_VLAN_CTAG_RX enabled we don't observe the checksum
issue, so amend the workaround to only drop back to s/w
checksums if VLAN offload is disabled.
See #2458.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
The chip supports stripping the VLAN tag and reporting it
in metadata. Implement this as it also appears to solve the
issues observed in checksum computation.
See #2458.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
HW_VLAN_CTAG_FILTER was partially implemented, but not fully to Linux.
Complete the implementation of this.
See #2458.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
There appears to be some issue in the LAN78xx where the checksum
computed on a VLAN tagged packet is incorrect, or at least not
in the form that the kernel is after. This is most easily shown
by pinging a device via a VLAN tagged interface and it will dump
out the error message and stack trace from netdev_rx_csum_fault.
It has also been seen with standard TCP and UDP packets.
Until this is fully understood, request that the network stack
computes the checksum on packets signalled as having a VLAN tag
applied.
See https://github.com/raspberrypi/linux/issues/2458
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Enable EEE mode as soon as possible after connecting to the PHY, and
before phy_start. This avoids a second link negotiation, which speeds
up booting and stops the interface failing to become ready.
See: https://github.com/raspberrypi/linux/issues/2437
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The frame abort timeout being set by lan78xx_set_rx_max_frame_length
didn't account for any VLAN headers, resulting in very low
throughput if used with tagged VLANs.
Use VLAN_ETH_HLEN instead of ETH_HLEN to correct for this.
See https://github.com/raspberrypi/linux/issues/2458
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
The patch to set the lan78xx MAC address from DT does so regardless of
whether or not the interface already has a valid address. As the
initialisation function is called from the reset handler when the
interface is brought up, it is impossible to change the MAC address
in a way that persists across the interface being brought up.
Fix the problem by moving the DT reading code after the check for a
valid address.
See: https://www.raspberrypi.org/forums/viewtopic.php?f=28&t=209309
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Add support for DT property "microchip,led-modes", a vector of two
cells (u32s) in the range 0-15, each of which sets the mode for one
of the two LEDs. The possible values are:
0=link/activity 1=link1000/activity
2=link100/activity 3=link10/activity
4=link100/1000/activity 5=link10/1000/activity
6=link10/100/activity 14=off 15=on
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
By user request, add a switch to prevent the clocks being stopped when
the stream is paused, stopped or shutdown. Provide access to the switch
by adding a 'non-stop-clocks' parameter to the audioinjector-addons
overlay.
See: https://github.com/raspberrypi/linux/issues/2409
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
It seems that trying to go from unlatched to unlatched will time out
waiting for STOP, and we can just skip that.
Signed-off-by: Eric Anholt <eric@anholt.net>
We don't use the same async update path between fkms and normal kms,
and the normal kms workaround ended up making us wait. This became a
larger problem in rpi-4.14.y, as the USB HID update rate throttling
got (accidentally?) dropped.
Signed-off-by: Eric Anholt <eric@anholt.net>
The SMICS interrupt fires continuously, but since it's 1/100 the rate
of the USB interrupts, we don't really need a way to turn it off. We
do need to make sure that we don't tell DRM about it until DRM has
asked for the interrupt at least once, because otherwise it will throw
a warning at boot time.
Signed-off-by: Eric Anholt <eric@anholt.net>
The default LED modes put 1000Mb/activity on orange and 100Mb/activity
on green, but this leaves no indication for a 10Mb link. Change the
defaults to put 10Mb/100Mb/activity on green.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Add two new DT properties:
* microchip,eee-enabled - a boolean to enable EEE
* microchip,tx-lpi-timer - time in microseconds to wait before entering
low power state
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
This warning appears with GCC 6.4.0 from toolchains.bootlin.com:
../drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c: In function ‘vchiq_open’:
../drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c:1735:7: warning: unused variable ‘ret’ [-Wunused-variable]
int ret;
^~~
This variable's usage was removed by commit 3c980263c5 ("staging:
vchiq_arm: Make debugfs failure non-fatal"), making it useless.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
This warning appears with GCC 6.4.0 from toolchains.bootlin.com:
../sound/soc/bcm/allo-piano-dac-plus.c: In function ‘snd_allo_piano_dac_init’:
../sound/soc/bcm/allo-piano-dac-plus.c:711:30: warning: argument to ‘sizeof’ in ‘memset’ call is the same expression as the destination; did you mean to dereference it? [-Wsizeof-pointer-memaccess]
memset(glb_ptr, 0x00, sizeof(glb_ptr));
^
Suggested-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Under-voltage due to inadequate power supplies is a recurring problem for
new Raspberry Pi users. There are visual indications that an
under-voltage situation is occuring like blinking power led and a
lightning icon on the desktop (not shown when using the vc4 driver), but
for new users it's not obvious that this signifies a critical situation.
This patch provides a twofold improvement to the situation:
Firstly it logs under-voltage events to the kernel log. This provides
information also for headless installations.
Secondly it provides a sysfs file to read the value. This improves on
'vcgencmd' by providing change notification. Userspace can poll on the
file and be notified of changes to the value.
A script can poll the file and use dbus notification to put a windows on
the desktop with information about the severity with a recommendation to
change the power supply. A link to more information can also be provided.
Only changes to the sticky bits are reported (cleared between readings).
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Prevent voltage low warnings from filling log
Although the correct fix for low voltage warnings is to
improve the power supply, the current implementation
of the detection can fill the log if the warning
happens freqently. This replaces the logging with
slightly custom ratelimited logging.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
Reduce log spam when mailbox call not implemented
This changes the logging message when a mailbox call
fails to the dev_dbg level. In addition, it fixes the
low voltage detection logging code so that if the
mailbox call doies fails, it logs at error level
and flags so the call is no longer attempted.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
The SC16IS752 is a dual-channel device. The two channels are largely
independent, but the IRQ signals are wired together as an open-drain,
active low signal which will be driven low while either of the
channels requires attention, which can be for significant periods of
time until operations complete and the interrupt can be acknowledged.
In that respect it is should be treated as a true level-sensitive IRQ.
The kernel, however, needs to be able to exit interrupt context in
order to use I2C or SPI to access the device registers (which may
involve sleeping). Therefore the interrupt needs to be masked out or
paused in some way.
The usual way to manage sleeping from within an interrupt handler
is to use a threaded interrupt handler - a regular interrupt routine
does the minimum amount of work needed to triage the interrupt before
waking the interrupt service thread. If the threaded IRQ is marked as
IRQF_ONESHOT the kernel will automatically mask out the interrupt
until the thread runs to completion. The sc16is7xx driver used to
use a threaded IRQ, but a patch switched to using a kthread_worker
in order to set realtime priorities on the handler thread and for
other optimisations. The end result is non-threaded IRQ that
schedules some work then returns IRQ_HANDLED, making the kernel
think that all IRQ processing has completed.
The work-around to prevent a constant stream of interrupts is to
mark the interrupt as edge-sensitive rather than level-sensitive,
but interpreting an active-low source as a falling-edge source
requires care to prevent a total cessation of interrupts. Whereas
an edge-triggering source will generate a new edge for every interrupt
condition a level-triggering source will keep the signal at the
interrupting level until it no longer requires attention; in other
words, the host won't see another edge until all interrupt conditions
are cleared. It is therefore vital that the interrupt handler does not
exit with an outstanding interrupt condition, otherwise the kernel
will not receive another interrupt unless some other operation causes
the interrupt state on the device to be cleared.
The existing sc16is7xx driver has a very simple interrupt "thread"
(kthread_work job) that processes interrups on each channel in turn
until there are no more. If both channels are active and the first
channel starts interrupting while the handler for the second channel
is running then it will not be detected and an IRQ stall ensues. This
could be handled easily if there was a shared IRQ status register, or
a convenient way to determine if the IRQ had been deasserted for any
length of time, but both appear to be lacking.
Avoid this problem (or at least make it much less likely to happen)
by reducing the granularity of per-channel interrupt processing
to one condition per iteration, only exiting the overall loop when
both channels are no longer interrupting.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
I2C busses can be assigned specific bus numbers using aliases in
Device Tree - string properties where the name is the alias and the
value is the path to the node. The current DT parameter mechanism
does not allow property names to be derived from a parameter value
in any way, so it isn't possible to generate unique or matching
aliases for nodes from an overlay that can generate multiple
instances, e.g. i2c-gpio.
Work around this limitation (at least temporarily) by allowing
the i2c adapter number to be initialised from the "reg" property
if present.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
This ensures that the screen goes blank during DPMS (screensaver),
including the cursor. Planes don't necessarily get disabled during
CRTC disable, so we need to be careful to not leave them on or turn
them back on early.
Signed-off-by: Eric Anholt <eric@anholt.net>
In the rewrite of vc4_crtc.c for fkms, I dropped the part of the
CRTC's atomic flush handler that moved the completion event from the
proposed atomic state change to the CRTC's current state. That meant
that when full screen pageflipping happened (glxgears -fullscreen in
X, compton, por weston), the app would end up blocked firever waiting
to draw its next frame.
Signed-off-by: Eric Anholt <eric@anholt.net>
There is a new test in __irq_startup that the IRQ is activated, which
hasn't been the case for FIQs since they bypass some of the usual setup.
Augment enable_fiq to include a call to irq_activate to avoid the
warning.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The VideoCore bootloader passes in Serial number and
Revision number through Device Tree. Make these available to
userspace through /proc/cpuinfo.
Mainline status:
There is a commit in linux-next that standardize passing the serial
number through Device Tree (string: /serial-number):
ARM: 8355/1: arch: Show the serial number from devicetree in cpuinfo
There was an attempt to do the same with the revision number, but it
didn't get in:
[PATCH v2 1/2] arm: devtree: Set system_rev from DT revision
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Driver was using a fixed resolution, this commit
adds touchscreen size, and coordinate flip and swap
features via device tree overlays.
Adds overrides so the VC4 can adjust the DT parameters
appropriately; there is a newer version of the VC4 side
driver that can now set up the appropriate DT values
if required.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
The MCP2515 datasheet clearly describes a level-triggered interrupt
pin. Therefore the receiving interrupt controller must also be
configured for level-triggered operation otherwise there is a danger
of a missed interrupt condition blocking all subsequent interrupts.
The ONESHOT flag ensures that the interrupt is masked until the
threaded interrupt handler exits.
Rather than change the flags globally (they must have worked for at
least one user), allow the flags to be overridden from Device Tree
in the event that the device has a DT node.
See: https://github.com/raspberrypi/linux/issues/2175https://github.com/raspberrypi/linux/issues/2263
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Uses the debugfs I/F to provide access to the AXI
bus performance monitors.
Requires the new mailbox peripheral access for access
to the VPU performance registers, system bus access
is done using direct register reads.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
IRQ-CPU mapping is round robined on ARM64 to increase
concurrency and allow multiple interrupts to be serviced
at a time. This reduces the need for FIQ.
Signed-off-by: Michael Zoran <mzoran@crowfest.net>
In ARM64, the FIQ mechanism used by this driver is not current
implemented. As a workaround, reqular IRQ is used instead
of FIQ.
In a separate change, the IRQ-CPU mapping is round robined
on ARM64 to increase concurrency and allow multiple interrupts
to be serviced at a time. This reduces the need for FIQ.
Tests Run:
This mechanism is most likely to break when multiple USB devices
are attached at the same time. So the system was tested under
stress.
Devices:
1. USB Speakers playing back a FLAC audio through VLC
at 96KHz.(Higher then typically, but supported on my speakers).
2. sftp transferring large files through the buildin ethernet
connection which is connected through USB.
3. Keyboard and mouse attached and being used.
Although I do occasionally hear some glitches, the music seems to
play quite well.
Signed-off-by: Michael Zoran <mzoran@crowfest.net>
ARM64: Modify default config to get raspbian to boot (#1686)
1. Enable emulation of deprecated instructions.
2. Enable ARM 8.1 and 8.2 features which are not detected at runtime.
3. Switch the default governer to powersave.
4. Include the watchdog timer driver in the kernel image rather then a module.
Tested with raspbian-jessie 2016-09-23.
ARM64: Make it work again on 4.9 (#1790)
* Invoke the dtc compiler with the same options used in arm mode.
* ARM64 now uses the bcm2835 platform just like ARM32.
* ARM64: Update bcmrpi3_defconfig
Signed-off-by: Michael Zoran <mzoran@crowfest.net>
Update arm64 Makefile to compile bcm2710 dtb file
The line 'dtb-$(CONFIG_ARCH_BCM2835) += bcm2710-rpi-3-b.dtb' has been copied from previous rpi-4.14.y version into rpi-4.15.y arch/arm64/boot/dts/broadcom/Makefile to restore compilation of bcm2710-rpi-3-b.dtb device tree blob under 'make ARCH=arm64 dtbs' command.
Since we don't have any CLM-capable firmware yet, silence the warning
of its absence by using request_firmware_direct, which should also
be marginally quicker.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The brcmfmac WiFi driver always complains about the '00' country code.
Modify the driver to ignore '00' silently.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
brcmfmac: Disable power management
Disable wireless power saving in the brcmfmac WLAN driver. This is a
temporary measure until the connectivity loss resulting from power
saving is resolved.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
brcmfmac: Use original country code as a fallback
Commit 73345fd212:
brcmfmac: Configure country code using device specific settings
prevents region codes from working on devices that lack a region code
translation table. In the event of an absent table, preserve the old
behaviour of using the provided code as-is.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
brcmfmac: Plug memory leak in brcmf_fill_bss_param
See: https://github.com/raspberrypi/linux/issues/1471
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
brcmfmac: do not use internal roaming engine by default
Some evidence of curing disconnects with this disabled, so make it a default.
Can be overridden with module parameter roamoff=0
See: http://projectable.me/optimize-my-pi-wi-fi/
brcmfmac: Change stop_ap sequence
Patch from Broadcom/Cypress to resolve a customer error
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
This is a port of Pantelis Antoniou's v3 port that makes use of the
new upstreamed configfs support for binary attributes.
Original commit message:
Add a runtime interface to using configfs for generic device tree overlay
usage. With it its possible to use device tree overlays without having
to use a per-platform overlay manager.
Please see Documentation/devicetree/configfs-overlays.txt for more info.
Changes since v2:
- Removed ifdef CONFIG_OF_OVERLAY (since for now it's required)
- Created a documentation entry
- Slight rewording in Kconfig
Changes since v1:
- of_resolve() -> of_resolve_phandles().
Originally-signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
DT configfs: Fix build errors on other platforms
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
DT configfs: fix build error
There is an error when compiling rpi-4.6.y branch:
CC drivers/of/configfs.o
drivers/of/configfs.c:291:21: error: initialization from incompatible pointer type [-Werror=incompatible-pointer-types]
.default_groups = of_cfs_def_groups,
^
drivers/of/configfs.c:291:21: note: (near initialization for 'of_cfs_subsys.su_group.default_groups.next')
The .default_groups is linked list since commit
1ae1602de0.
This commit uses configfs_add_default_group to fix this problem.
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
configfs: New of_overlay API
These warnings appear with GCC 7.3.0 from toolchains.bootlin.com:
../drivers/net/wireless/realtek/rtl8192cu/core/rtw_mlme_ext.c: In function ‘mgt_dispatcher’:
../drivers/net/wireless/realtek/rtl8192cu/core/rtw_mlme_ext.c:734:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if(check_fwstate(pmlmepriv, WIFI_AP_STATE) == _TRUE)
^
../drivers/net/wireless/realtek/rtl8192cu/core/rtw_mlme_ext.c:739:3: note: here
case WIFI_ASSOCREQ:
^~~~
../drivers/net/wireless/realtek/rtl8192cu/hal/rtl8192c/rtl8192c_phycfg.c: In function ‘phy_TxPwrIdxToDbm’:
../drivers/net/wireless/realtek/rtl8192cu/hal/rtl8192c/rtl8192c_phycfg.c:2365:10: warning: this statement may fall through [-Wimplicit-fallthrough=]
Offset = -8;
~~~~~~~^~~~
../drivers/net/wireless/realtek/rtl8192cu/hal/rtl8192c/rtl8192c_phycfg.c:2366:2: note: here
default:
^~~~~~~
../drivers/net/wireless/realtek/rtl8192cu/hal/rtl8192c/usb/usb_halinit.c: In function ‘GetHwReg8192CU’:
../drivers/net/wireless/realtek/rtl8192cu/hal/rtl8192c/usb/usb_halinit.c:5694:20: warning: this statement may fall through [-Wimplicit-fallthrough=]
*((u16 *)(val)) = pHalData->BasicRateSet;
~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~
../drivers/net/wireless/realtek/rtl8192cu/hal/rtl8192c/usb/usb_halinit.c:5695:3: note: here
case HW_VAR_TXPAUSE:
^~~~
../drivers/net/wireless/realtek/rtl8192cu/os_dep/linux/ioctl_linux.c: In function ‘set_group_key’:
../drivers/net/wireless/realtek/rtl8192cu/os_dep/linux/ioctl_linux.c:7383:11: warning: this statement may fall through [-Wimplicit-fallthrough=]
keylen = 16;
~~~~~~~^~~~
../drivers/net/wireless/realtek/rtl8192cu/os_dep/linux/ioctl_linux.c:7384:3: note: here
default:
^~~~~~~
../drivers/net/wireless/realtek/rtl8192cu/os_dep/linux/ioctl_cfg80211.c: In function ‘set_group_key’:
../drivers/net/wireless/realtek/rtl8192cu/os_dep/linux/ioctl_cfg80211.c:822:11: warning: this statement may fall through [-Wimplicit-fallthrough=]
keylen = 16;
~~~~~~~^~~~
../drivers/net/wireless/realtek/rtl8192cu/os_dep/linux/ioctl_cfg80211.c:823:3: note: here
default:
^~~~~~~
None of them appear to be a real issue but it is trivial to make the
warnings go away.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
These warnings appear with GCC 6.4.0 from toolchains.bootlin.com:
../drivers/net/wireless/realtek/rtl8192cu/core/rtw_security.c: In function ‘aes_cipher’:
../drivers/net/wireless/realtek/rtl8192cu/core/rtw_security.c:1504:5: warning: this ‘for’ clause does not guard... [-Wmisleading-indentation]
for (j = 0; j < 8; j++)
^~~
../drivers/net/wireless/realtek/rtl8192cu/core/rtw_security.c:1507:2: note: ...this statement, but the latter is misleadingly indented as if it is guarded by the ‘for’
payload_index = hdrlen + 8;
^~~~~~~~~~~~~
../drivers/net/wireless/realtek/rtl8192cu/core/rtw_security.c: In function ‘aes_decipher’:
../drivers/net/wireless/realtek/rtl8192cu/core/rtw_security.c:1878:5: warning: this ‘for’ clause does not guard... [-Wmisleading-indentation]
for (j = 0; j < 8; j++)
^~~
../drivers/net/wireless/realtek/rtl8192cu/core/rtw_security.c:1881:2: note: ...this statement, but the latter is misleadingly indented as if it is guarded by the ‘for’
payload_index = hdrlen + 8;
^~~~~~~~~~~~~
../drivers/net/wireless/realtek/rtl8192cu/core/rtw_mlme_ext.c:5666:5: warning: this ‘if’ clause does not guard... [-Wmisleading-indentation]
if( _rtw_memcmp(pwdinfo->rx_prov_disc_info.peerDevAddr, empty_addr, ETH_ALEN) );
^~
../drivers/net/wireless/realtek/rtl8192cu/core/rtw_mlme_ext.c:5667:6: note: ...this statement, but the latter is misleadingly indented as if it is guarded by the ‘if’
_rtw_memcpy(pwdinfo->rx_prov_disc_info.peerDevAddr, GetAddr2Ptr(pframe), ETH_ALEN);
^~~~~~~~~~~
It appears to be due to tabs versus spaces.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
suppress spurious messages
Add #if for 3.14 kernel change (#87)
Fixes compiling after changes in f663dd9aaf and 99932d4fc0Fixes#86
Set dev_type to wlan
Fixes#23
Tentatively added support for more 8188CUS based devices.
Add support for more 8188CUS and 8192CUS devices
Add ProductId for the Netgear N150 - WNA1000M
Fixes CONFIG_CONCURRENT_MODE CONFIG_MULTI_VIR_IFACES
Fixes compatibility with 3.13
Enables warning in the compiler and fixes some issues, reference => https://github.com/diederikdehaas/rtl8812AU
Starts device in station mode instead of monitor, fixes NetworkManager issues
Enable cfg80211 support
Fix cfg80211 for kernel >= 4.7
Fixes rtl8192cu for kernel >= 4.8
rtl8192: Fixup build
fixup: rtl8192cu fixes from milhouse
rtl8192: switch to netdev->priv_destructor()
When trying to build from the rpi-4.11.y branch, I'm getting the
following error :
drivers/net/wireless/realtek/rtl8192cu/os_dep/linux/ioctl_cfg80211.c:3464:10: error: 'struct net_device' has no member named 'destructor'
It seems to occur since this upstream commit :
cf124db566
[...]
netdev->priv_destructor() performs all actions to free up the private
resources that used to be freed by netdev->destructor(), except for
free_netdev().
netdev->needs_free_netdev is a boolean that indicates whether
free_netdev() should be done at the end of unregister_netdevice().
Signed-off-by: Bilal Amarni <bilal.amarni@gmail.com>
ARM64: Fix build break for RTL8187/RTL8192CU wifi
These drivers use an ASM function from the base
system to compute the ipv6 checksum. These functions
are not available on ARM64, probably because nobody
has bother to write them. The base system does have
a generic "C" version, so a simple fix is to include
the header to use the generic version on ARM64 only.
A longer term solution would be to submit the necessary
ASM function to the upstream source.
With this change, these drivers now compile without
any errors on ARM64.
Signed-off-by: Michael Zoran <mzoran@crowfest.net>
Add non-mainline source for rtl8192cu wireless driver version v4.0.2_9000 as
this is widely used. Disable older rtlwifi driver.
8192cu needs old wireless extensions
The obsolete WIRELESS_EXT configuration is used
by the old Realtek code and is needed for AP support.
8192cu: CONFIG_AP_MODE hardcoded in autoconf.h
rtl8192c_rf6052: PHY_RFShadowRefresh(): fix off-by-one
Signed-off-by: Marc Kleine-Budde <mkl@blackshift.org>
rtl8192cu: Add PID for D-Link DWA 131
Add a mailbox-driven backlight controller for the Raspberry Pi DSI
touchscreen display. Requires updated GPU firmware to recognise the
mailbox request.
Signed-off-by: Gordon Hollingworth <gordon@raspberrypi.org>
Add Raspberry Pi firmware driver to the dependencies of backlight driver
Otherwise the backlight driver fails to build if the firmware
loading driver is not in the kernel
Signed-off-by: Alex Riesen <alexander.riesen@cetitec.com>
AudioInjector Octo: sample rates, regulators, reset
This patch adds new sample rates to the Audioinjector Octo sound card. The
new supported rates are (in kHz) :
96, 48, 32, 24, 16, 8, 88.2, 44.1, 29.4, 22.05, 14.7
Reference the bcm270x DT regulators in the overlay.
This patch adds a reset GPIO for the AudioInjector.net octo sound card.
Audioinjector octo : Make the playback and capture symmetric
This patch ensures that the sample rate and channel count of the audioinjector
octo sound card are symmetric.
Fe-Pi Audio Sound Card is based on NXP SGTL5000 codec.
Mechanical specification of the board is the same the Raspberry Pi Zero.
3.5mm jacks for Headphone/Mic, Line In, and Line Out.
Signed-off-by: Henry Kupis <fe-pi@cox.net>
Signed-off-by: Miquel Blauw <info@dionaudio.nl>
ASoC: dionaudio_loco-v2: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Also remove hw_params and ops as they are no longer needed.
Signed-off-by: Matthias Reichl <hias@horus.com>
Note: due to problems with deferred probing of regulators
the following softdep should be added to a modprobe.d file
softdep arizona-spi pre: arizona-ldo1
Signed-off-by: Matthias Reichl <hias@horus.com>
Pisound dynamic overlay (#1760)
Restructuring pisound-overlay.dts, so it can be loaded and unloaded dynamically using dtoverlay.
Print a logline when the kernel module is removed.
pisound improvements:
* Added a writable sysfs object to enable scripts / user space software
to blink MIDI activity LEDs for variable duration.
* Improved hw_param constraints setting.
* Added compatibility with S16_LE sample format.
* Exposed some simple placeholder volume controls, so the card appears
in volumealsa widget.
Add missing SND_PISOUND selects dependency to SND_RAWMIDI
Without it the Pisound module fails to compile.
See https://github.com/raspberrypi/linux/issues/2366
Updates for Pisound module code:
* Merged 'Fix a warning in DEBUG builds' (1c8b82b).
* Updating some strings and copyright information.
* Fix for handling high load of MIDI input and output.
* Use dual rate oversampling ratio for 96kHz instead of single
rate one.
Signed-off-by: Giedrius Trainavicius <giedrius@blokas.io>
Fixing memset call in pisound.c
Signed-off-by: Giedrius Trainavicius <giedrius@blokas.io>
Fix for Pisound's MIDI Input getting blocked for a while in rare cases.
There was a possible race condition which could lead to Input's FIFO queue
to be underflown, causing high amount of processing in the worker thread for
some period of time.
Signed-off-by: Giedrius Trainavicius <giedrius@blokas.io>
The Piano DAC 2.1 has support for 4 channels with subwoofer.
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net>
Reviewed-by: Vijay Kumar B. <vijaykumar@zilogic.com>
Reviewed-by: Raashid Muhammed <raashidmuhammed@zilogic.com>
Add clock changes and mute gpios (#1938)
Also improve code style and adhere to ALSA coding conventions.
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net>
Reviewed-by: Vijay Kumar B. <vijaykumar@zilogic.com>
Reviewed-by: Raashid Muhammed <raashidmuhammed@zilogic.com>
PianoPlus: Dual Mono & Dual Stereo features added (#2069)
allo-piano-dac-plus: Master volume added + fixes
Master volume added, which controls both DACs volumes.
See: https://github.com/raspberrypi/linux/pull/2149
Also fix initial max volume, default mode value, and unmute.
Signed-off-by: allocom <sparky-dev@allo.com>
ASoC: allo-piano-dac-plus: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Signed-off-by: Matthias Reichl <hias@horus.com>
Add initial 2 channel (stereo) support for Allo Piano DAC (2.0/2.1) boards,
using allo-piano-dac-pcm512x-audio overlay and allo-piano-dac ALSA ASoC
machine driver.
NB. The initial support is 2 channel (stereo) ONLY!
(The Piano DAC 2.1 will only support 2 channel (stereo) left/right output,
pending an update to the upstream pcm512x codec driver, which will have
to be submitted via upstream. With the initial downstream support,
provided by this patch, the Piano DAC 2.1 subwoofer outputs will
not function.)
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net>
Signed-off-by: Clive Messer <clive.messer@digitaldreamtime.co.uk>
Tested-by: Clive Messer <clive.messer@digitaldreamtime.co.uk>
ASoC: allo-piano-dac: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Also remove hw_params and ops as they are no longer needed.
Signed-off-by: Matthias Reichl <hias@horus.com>
Support IQAudIO Digi board with iqaudio_digi machine driver and
iqaudio-digi-wm8804-audio overlay.
NB. Machine driver is a cut and paste of hifiberry_digi code, with format
and general cleanup to comply with kernel coding standards.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
Contains the sound/soc/bcm ALSA machine driver and necessary alterations to the Kconfig and Makefile.
Adds the dts overlay and updates the Makefile and README.
Updates the relevant defconfig files to enable building for the Raspberry Pi.
Thanks to Phil Elwell (pelwell) for the review, simple-card concepts and discussion. Thanks to Clive Messer for overlay naming suggestions.
Added support for headphones, microphone and bclk_ratio settings.
This patch adds headphone and microphone capability to the Audio Injector sound card. The patch also sets the bit clock ratio for use in the bcm2835-i2s driver. The bcm2835-i2s can't handle an 8 kHz sample rate when the bit clock is at 12 MHz because its register is only 10 bits wide which can't represent the ch2 offset of 1508. For that reason, the rate constraint is added.
This commit adds basic support for the codec usage including: Device tree overlay,
binding I2S bus and setting I2S mode, clock source and frequency setting according
to spec.
Signed-off-by: Andrey Grodzovsky <andrey2805@gmail.com>
justboom-dac: Adjust for ALSA API change
As of 4.4, snd_soc_limit_volume now takes a struct snd_soc_card *
rather than a struct snd_soc_codec *.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
ASoC: justboom-dac: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Also remove hw_params as it's no longer needed.
Signed-off-by: Matthias Reichl <hias@horus.com>
The driver contains a low-level hardware driver for the TAS5713 and the
drivers for the Raspberry Pi I2S subsystem.
TAS5713: return error if initialisation fails
Existing TAS5713 driver logs errors during initialisation, but does not return
an error code. Therefore even if initialisation fails, the driver will still be
loaded, but won't work. This patch fixes this. I2C communication error will now
reported correctly by a non-zero return code.
HiFiBerry Amp: fix device-tree problems
Some code to load the driver based on device-tree-overlays was missing. This is added by this patch.
The driver is based on the HiFiBerry DAC driver. However HiFiBerry DAC+ uses
a different codec chip (PCM5122), therefore a new driver is necessary.
Add support for the HiFiBerry DAC+ Pro.
The HiFiBerry DAC+ and DAC+ Pro products both use the existing bcm sound driver with the DAC+ Pro having a special clock device driver representing the two high precision oscillators.
An addition bug fix is included for the PCM512x codec where by the physical size of the sample frame is used in the calculation of the LRCK divisor as it was found to be wrong when using 24-bit depth sample contained in a little endian 4-byte sample frame.
Limit PCM512x "Digital" gain to 0dB by default with HiFiBerry DAC+
24db_digital_gain DT param can be used to specify that PCM512x
codec "Digital" volume control should not be limited to 0dB gain,
and if specified will allow the full 24dB gain.
Add dt param to force HiFiBerry DAC+ Pro into slave mode
"dtoverlay=hifiberry-dacplus,slave"
Add 'slave' param to use HiFiBerry DAC+ Pro in slave mode,
with Pi as master for bit and frame clock.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
Fixed a bug when using 352.8kHz sample rate
Signed-off-by: Daniel Matuschek <daniel@hifiberry.com>
ASoC: pcm512x: revert downstream changes
This partially reverts commit 185ea05465
which was added by https://github.com/raspberrypi/linux/pull/1152
The downstream pcm512x changes caused a regression, it broke normal
use of the 24bit format with the codec, eg when using simple-audio-card.
The actual bug with 24bit playback is the incorrect usage
of physical_width in various drivers in the downstream tree
which causes 24bit data to be transmitted with 32 clock
cycles. So it's not the pcm512x that needs fixing, it's the
soundcard drivers.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: hifiberry_dacplus: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: hifiberry_dacplus: transmit S24_LE with 64 BCLK cycles
Signed-off-by: Matthias Reichl <hias@horus.com>
Set a limit of 0dB on Digital Volume Control
The main volume control in the PCM512x DAC has a range up to
+24dB. This is dangerously loud and can potentially cause massive
clipping in the output stages. Therefore this sets a sensible
limit of 0dB for this control.
Allow up to 24dB digital gain to be applied when using IQAudIO DAC+
24db_digital_gain DT param can be used to specify that PCM512x
codec "Digital" volume control should not be limited to 0dB gain,
and if specified will allow the full 24dB gain.
Modify IQAudIO DAC+ ASoC driver to set card/dai config from dt
Add the ability to set the card name, dai name and dai stream name, from
dt config.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
IQaudIO: auto-mute for AMP+ and DigiAMP+
IQAudIO amplifier mute via GPIO22. Add dt params for "one-shot" unmute
and auto mute.
Revision 2, auto mute implementing HiassofT suggestion to mute/unmute
using set_bias_level, rather than startup/shutdown....
"By default DAPM waits 5 seconds (pmdown_time) before shutting down
playback streams so a close/stop immediately followed by open/start
doesn't trigger an amp mute+unmute."
Tested on both AMP+ (via DAC+) and DigiAMP+, with both options...
dtoverlay=iqaudio-dacplus,unmute_amp
"one-shot" unmute when kernel module loads.
dtoverlay=iqaudio-dacplus,auto_mute_amp
Unmute amp when ALSA device opened by a client. Mute, with 5 second delay
when ALSA device closed. (Re-opening the device within the 5 second close
window, will cancel mute.)
Revision 4, using gpiod.
Revision 5, clean-up formatting before adding mute code.
- Convert tab plus 4 space formatting to 2x tab
- Remove '// NOT USED' commented code
Revision 6, don't attempt to "one-shot" unmute amp, unless card is
successfully registered.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
ASoC: iqaudio-dac: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Signed-off-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Daniel Matuschek <daniel@matuschek.net>
Add a parameter to turn off SPDIF output if no audio is playing
This patch adds the paramater auto_shutdown_output to the kernel module.
Default behaviour of the module is the same, but when auto_shutdown_output
is set to 1, the SPDIF oputput will shutdown if no stream is playing.
bugfix for 32kHz sample rate, was missing
HiFiBerry Digi: set SPDIF status bits for sample rate
The HiFiBerry Digi driver did not signal the sample rate in the SPDIF status bits.
While this is optional, some DACs and receivers do not accept this signal. This patch
adds the sample rate bits in the SPDIF status block.
Added HiFiBerry Digi+ Pro driver
Signed-off-by: Daniel Matuschek <daniel@hifiberry.com>
This adds a machine driver for the HifiBerry DAC.
It is a sound card that can
be stacked onto the Raspberry Pi.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
PCM512x can accept data padded with additional BCLK cycles
but the driver currently lacks an interface to configure this.
This leads to the problem that S24_LE format in master mode
can result in non-integer clock divisors and pcm512x running
at a rather off rate.
For example 48kHz with 48fs BCLK and SCLK at 24.576MHz uses
a divisor of 10 (rounded down from 10.6666) and results in a
51.2kHz LRCLK. With 64fs BCLK a divisor of 8 is used and
LRCLK runs at exactly 48kHz.
Fix this by providing a minimal set_tdm_slot implementation
so machine drivers can optionally configure custom BCLK ratios.
Signed-off-by: Matthias Reichl <hias@horus.com>
The Raspberry Pi firmware manages the power-down and reboot
process. To do this it installs a pm_power_off handler, causing
the gpio-poweroff module to abort the probe function.
This patch introduces a "force" DT property that overrides that
behaviour, and also adds a DT overlay to enable and control it.
Note that running in an active-low configuration (DT parameter
"active_low") requires a custom dt-blob.bin and probably won't
allow a reboot without switching off, so an external inversion
of the trigger signal may be preferable.
Provide a __copy_from_user that uses memcpy. On BCM2708, use
optimised memcpy/memmove/memcmp/memset implementations.
arch/arm: Add mmiocpy/set aliases for memcpy/set
See: https://github.com/raspberrypi/linux/issues/1082
copy_from_user: CPU_SW_DOMAIN_PAN compatibility
The downstream copy_from_user acceleration must also play nice with
CONFIG_CPU_SW_DOMAIN_PAN.
See: https://github.com/raspberrypi/linux/issues/1381
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Fix driver detection failure Check that the buffer response is non-zero meaning the touchscreen was detected
rpi-ft5406: Use firmware API
RPI-FT5406: Enable aarch64 support through explicit iomem interface
Signed-off-by: Gerhard de Clercq <gerharddeclercq@outlook.com>
Based on the patch authored by Ali Gholami Rudi at
https://lkml.org/lkml/2009/7/13/153
Provide an ioctl for userspace applications, but only if this operation
is hardware accelerated (otherwide it does not make any sense).
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
bcm2708_fb: Add ioctl for reading gpu memory through dma
The "input" trigger makes the associated GPIO an input. This is to support
the Raspberry Pi PWR LED, which is driven by external hardware in normal use.
N.B. pwr_led is not available on Model A or B boards.
leds-gpio: Implement the brightness_get method
The power LED uses some clever logic that means it is driven
by a voltage measuring circuit when configured as input, otherwise
it is driven by the GPIO output value. This patch wires up the
brightness_get method for leds-gpio so that user-space can monitor
the LED value via /sys/class/gpio/led1/brightness. Using the input
trigger this returns an indication of the system power health,
otherwise it is just whatever value the trigger has written most
recently.
See: https://github.com/raspberrypi/linux/issues/1064
Add the bare minimum needed to boot BCM2708 from a Device Tree.
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
BCM2708: DT: change 'axi' nodename to 'soc'
Change DT node named 'axi' to 'soc' so it matches ARCH_BCM2835.
The VC4 bootloader fills in certain properties in the 'axi' subtree,
but since this is part of an upstreaming effort, the name is changed.
Signed-off-by: Noralf Tronnes notro@tronnes.org
BCM2708_DT: Correct length of the peripheral space
Use dts-dirs feature for overlays.
The kernel makefiles have a dts-dirs target that is for vendor subdirectories.
Using this fixes the install_dtbs target, which previously did not install the overlays.
BCM270X_DT: configure I2S DMA channels
Signed-off-by: Matthias Reichl <hias@horus.com>
BCM270X_DT: switch to bcm2835-i2s
I2S soundcard drivers with proper devicetree support (i.e. not linking
to the cpu_dai/platform via name but to cpu/platform via of_node)
will work out of the box without any modifications.
When the kernel is compiled without devicetree support the platform
code will instantiate the bcm2708-i2s driver and I2S soundcard drivers
will link to it via name, as before.
Signed-off-by: Matthias Reichl <hias@horus.com>
SDIO-overlay: add poll_once-boolean parameter
Add paramter to toggle sdio-device-polling
done every second or once at boot-time.
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
BCM270X_DT: Make mmc overlay compatible with current firmware
The original DT overlay logic followed a merge-then-patch procedure,
i.e. parameters are applied to the loaded overlay before the overlay
is merged into the base DTB. This sequence has been changed to
patch-then-merge, in order to support parameterised node names, and
to protect against bad overlays. As a result, overrides (parameters)
must only target labels in the overlay, but the overlay can obviously target nodes in the base DTB.
mmc-overlay.dts (that switches back to the original mmc sdcard
driver) is the only overlay violating that rule, and this patch
fixes it.
bcm270x_dt: Use the sdhost MMC controller by default
The "mmc" overlay reverts to using the other controller.
squash: Add cprman to dt
BCM270X_DT: Use clk_core for I2C interfaces
BCM270X_DT: Use bcm283x.dtsi, bcm2835.dtsi and bcm2836.dtsi
The mainline Device Tree files are quite close to downstream now.
Let's use bcm283x.dtsi, bcm2835.dtsi and bcm2836.dtsi as base files
for our dts files.
Mainline dts files are based on these files:
bcm2835-rpi.dtsi
bcm2835.dtsi bcm2836.dtsi
bcm283x.dtsi
Current downstream are based on these:
bcm2708.dtsi bcm2709.dtsi bcm2710.dtsi
bcm2708_common.dtsi
This patch introduces this dependency:
bcm2708.dtsi bcm2709.dtsi
bcm2708-rpi.dtsi
bcm270x.dtsi
bcm2835.dtsi bcm2836.dtsi
bcm283x.dtsi
And:
bcm2710.dtsi
bcm2708-rpi.dtsi
bcm270x.dtsi
bcm283x.dtsi
bcm270x.dtsi contains the downstream bcm283x.dtsi diff.
bcm2708-rpi.dtsi is the downstream version of bcm2835-rpi.dtsi.
Other changes:
- The led node has moved from /soc/leds to /leds. This is not a problem
since the label is used to reference it.
- The clk_osc reg property changes from 6 to 3.
- The gpu nodes has their interrupt property set in the base file.
- the clocks label does not point to the /clocks node anymore, but
points to the cprman node. This is not a problem since the overlays
that use the clock node refer to it directly: target-path = "/clocks";
- some nodes now have 2 labels since mainline and downstream differs in
this respect: cprman/clocks, spi0/spi, gpu/vc4.
- some nodes doesn't have an explicit status = "okay" since they're not
disabled in the base file: watchdog and random.
- gpiomem doesn't need an explicit status = "okay".
- bcm2708-rpi-cm.dts got the hpd-gpios property from bcm2708_common.dtsi,
it's now set directly in that file.
- bcm2709-rpi-2-b.dts has the timer node moved from /soc/timer to /timer.
- Removed clock-frequency property on the bcm{2709,2710}.dtsi timer nodes.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270X_DT: Use raspberrypi-power to turn on USB power
Use the raspberrypi-power driver to turn on USB power.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270X_DT: Add a .dtbo target, use for overlays
Change the filenames and extensions to keep the pre-DDT style of
overlay (<name>-overlay.dtb) distinct from new ones that use a
different style of local fixups (<name>.dtbo), and to match other
platforms.
The RPi firmware uses the DDTK trailer atom to choose which type of
overlay to use for each kernel.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: Don't generate "linux,phandle" props
The EPAPR standard says to use "phandle" properties to store phandles,
rather than the deprecated "linux,phandle" version. By default, dtc
generates both, but adding "-H epapr" causes it to only generate
"phandle"s, saving some space and clutter.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: Add overlay for enc28j60 on SPI2
Works on SPI2 for compute module
BCM270X_DT: Add midi-uart0 overlay
MIDI requires 31.25kbaud, a baudrate unsupported by Linux. The
midi-uart0 overlay configures uart0 (ttyAMA0) to use a fake clock
so that requesting 38.4kbaud actually gets 31.25kbaud.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: Add i2c-sensor overlay
The i2c-sensor overlay is a container for various pressure and
temperature sensors, currently bmp085 and bmp280. The standalone
bmp085_i2c-sensor overlay is now deprecated.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: overlays/*-overlay.dtb -> overlays/*.dtbo (#1752)
We now create overlays as .dtbo files.
build: support for .dtbo files for dtb overlays
Kernel 4.4.6+ on RaspberryPi support .dtbo files for overlays, instead of .dtb.
Patch the kernel, which has faulty rules to generate .dtbo the way yocto does
Signed-off-by: Herve Jourdain <herve.jourdain@neuf.fr>
Signed-off-by: Khem Raj <raj.khem@gmail.com>
BCM270X: Drop position requirement for CMA in VC4 overlay.
No longer necessary since 2aefcd5761,
and will probably let peeople that want to choose a larger CMA
allocation (particularly on pi0/1).
Signed-off-by: Eric Anholt <eric@anholt.net>
BCM270X_DT: RPi Device Tree tidy
Use the upstream sdhost node, add thermal-zones, and factor out some
common elements.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
kbuild: Silence unhelpful DTC warnings
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The Raspberry Pi firmware looks for a trailer on the kernel image to
determine whether it was compiled with Device Tree support enabled.
If the firmware finds a kernel without this trailer, or which has a
trailer indicating that it isn't DT-capable, it disables DT support
and reverts to using ATAGs.
The mkknlimg utility adds that trailer, having first analysed the
image to look for signs of DT support and the kernel version string.
knlinfo displays the contents of the trailer in the given kernel image.
scripts/mkknlimg: Add support for ARCH_BCM2835
Add a new trailer field indicating whether this is an ARCH_BCM2835
build, as opposed to MACH_BCM2708/9. If the loader finds this flag
is set it changes the default base dtb file name from bcm270x...
to bcm283y...
Also update knlinfo to show the status of the field.
scripts/mkknlimg: Improve ARCH_BCM2835 detection
The board support code contains sufficient strings to be able to
distinguish 2708 vs. 2835 builds, so remove the check for
bcm2835-pm-wdt which could exist in either.
Also, since the canned configuration is no longer built in (it's
a module), remove the config string checking.
See: https://github.com/raspberrypi/linux/issues/1157
scripts: Multi-platform support for mkknlimg and knlinfo
The firmware uses tags in the kernel trailer to choose which dtb file
to load. Current firmware loads bcm2835-*.dtb if the '283x' tag is true,
otherwise it loads bcm270*.dtb. This scheme breaks if an image supports
multiple platforms.
This patch adds '270X' and '283X' tags to indicate support for RPi and
upstream platforms, respectively. '283x' (note lower case 'x') is left
for old firmware, and is only set if the image only supports upstream
builds.
scripts/mkknlimg: Append a trailer for all input
Now that the firmware assumes an unsigned kernel is DT-capable, it is
helpful to be able to mark a kernel as being non-DT-capable.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
scripts/knlinfo: Decode DDTK atom
Show the DDTK atom as being a boolean.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
mkknlimg: Retain downstream-kernel detection
With the death of ARCH_BCM2708 and ARCH_BCM2709, a new way is needed to
determine if this is a "downstream" build that wants the firmware to
load a bcm27xx .dtb. The vc_cma driver is used downstream but not
upstream, making vc_cma_init a suitable predicate symbol.
mkknlimg: Find some more downstream-only strings
See: https://github.com/raspberrypi/linux/issues/1920
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
scripts: Update mkknlimg, just in case
With the removal of the vc_cma driver, mkknlimg lost an indication that
the user had built a downstream kernel. Update the script, adding a few
more key strings, in case it is still being used.
Note that mkknlimg is now deprecated, except to tag kernels as upstream
(283x), and thus requiring upstream DTBs.
See: https://github.com/raspberrypi/linux/issues/2239
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Support booting without Device Tree.
Turn on USB power.
Load driver early because of lacking support for deferred probing
in many drivers.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
firmware: bcm2835: Don't turn on USB power
The raspberrypi-power driver is now used to turn on USB power.
This partly reverts commit:
firmware: bcm2835: Support ARCH_BCM270x
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Add module for accessing the mailbox property channel through
/dev/vcio. Was previously in bcm2708-vcio.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
i2c-bcm2708: fixed baudrate
Fixed issue where the wrong CDIV value was set for baudrates below 3815 Hz (for 250MHz bus clock).
In that case the computed CDIV value was more than 0xffff. However the CDIV register width is only 16 bits.
This resulted in incorrect setting of CDIV and higher baudrate than intended.
Example: 3500Hz -> CDIV=0x11704 -> CDIV(16bit)=0x1704 -> 42430Hz
After correction: 3500Hz -> CDIV=0x11704 -> CDIV(16bit)=0xffff -> 3815Hz
The correct baudrate is shown in the log after the cdiv > 0xffff correction.
Perform I2C combined transactions when possible
Perform I2C combined transactions whenever possible, within the
restrictions of the Broadcomm Serial Controller.
Disable DONE interrupt during TA poll
Prevent interrupt from being triggered if poll is missed and transfer
starts and finishes.
i2c: Make combined transactions optional and disabled by default
i2c: bcm2708: add device tree support
Add DT support to driver and add to .dtsi file.
Setup pins in .dts file.
i2c is disabled by default.
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
bcm2708: don't register i2c controllers when using DT
The devices for the i2c controllers are in the Device Tree.
Only register devices when not using DT.
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
I2C: Only register the I2C device for the current board revision
i2c_bcm2708: Fix clock reference counting
Fix grabbing lock from atomic context in i2c driver
2 main changes:
- check for timeouts in the bcm2708_bsc_setup function as indicated by this comment:
/* poll for transfer start bit (should only take 1-20 polls) */
This implies that the setup function can now fail so account for this everywhere it's called
- Removed the clk_get_rate call from inside the setup function as it locks a mutex and that's not ok since we call it from under a spin lock.
i2c-bcm2708: When using DT, leave the GPIO setup to pinctrl
i2c-bcm2708: Increase timeouts to allow larger transfers
Use the timeout value provided by the I2C_TIMEOUT ioctl when waiting
for completion. The default timeout is 1 second.
See: https://github.com/raspberrypi/linux/issues/260
i2c-bcm2708/BCM270X_DT: Add support for I2C2
The third I2C bus (I2C2) is normally reserved for HDMI use. Careless
use of this bus can break an attached display - use with caution.
It is recommended to disable accesses by VideoCore by setting
hdmi_ignore_edid=1 or hdmi_edid_file=1 in config.txt.
The interface is disabled by default - enable using the
i2c2_iknowwhatimdoing DT parameter.
bcm2708-spi: Don't use static pin configuration with DT
Also remove superfluous error checking - the SPI framework ensures the
validity of the chip_select value.
i2c-bcm2708: Remove non-DT support
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Set the BSC_CLKT clock streching timeout to 35ms as per SMBus specs.
Fixes i2c_bcm2708: Write to FIFO correctly - v2 (#1574)
* i2c: fix i2c_bcm2708: Clear FIFO before sending data
Make sure FIFO gets cleared before trying to send
data in case of a repeated start (COMBINED=Y).
* i2c: fix i2c_bcm2708: Only write to FIFO when not full
Check if FIFO can accept data before writing.
To avoid a peripheral read on the last iteration of a loop,
both bcm2708_bsc_fifo_fill and ~drain are changed as well.
Use clock manager instead of self-made clockmanager.
Also fix some error paths that showd up during development
(especially missing release of dma resources on rmmod)
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Add experimental support for the VideoCore shared memory service.
This allows user processes to allocate memory from VideoCore's
GPU relocatable heap and mmap the buffers. Additionally, the memory
handles can passed to other VideoCore services such as MMAL, OpenMax
and DispmanX
TODO
* This driver was originally released for BCM28155 which has a different
cache architecture to BCM2835. Consequently, in this release only
uncached mappings are supported. However, there's no fundamental
reason which cached mappings cannot be support or BCM2835
* More refactoring is required to remove the typedefs.
* Re-enable the some of the commented out debug-fs statistics which were
disabled when migrating code from proc-fs.
* There's a lot of code to support sharing of VCSM in order to support
Android. This could probably done more cleanly or perhaps just
removed.
Signed-off-by: Tim Gover <timgover@gmail.com>
config: Disable VC_SM for now to fix hang with cutdown kernel
vcsm: Use boolean as it cannot be built as module
On building the bcm_vc_sm as a module we get the following error:
v7_dma_flush_range and do_munmap are undefined in vc-sm.ko.
Fix by making it not an option to build as module
vcsm: Add ioctl for custom cache flushing
vc-sm: Move headers out of arch directory
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
vcsm: Treat EBUSY as success rather than SIGBUS
Currently if two cores access the same page concurrently one will return VM_FAULT_NOPAGE
and the other VM_FAULT_SIGBUS crashing the user code.
Also report when mapping fails.
Signed-off-by: popcornmix <popcornmix@gmail.com>
vcsm: Provide new ioctl to clean/invalidate a 2D block
vcsm: Convert to loading via device tree.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
VCSM: New option to import a DMABUF for VPU use
Takes a dmabuf, and then calls over to the VPU to wrap
it into a suitable handle.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
vcsm: fix multi-platform build
vcsm: add macros for cache functions
vcsm: use dma APIs for cache functions
* Will handle multi-platform builds
vcsm: Fix up macros to avoid breaking numbers used by existing apps
vcsm: Define cache operation constants in user header
Without this change, users have to use raw values (1, 2, 3) to specify
cache operation.
Signed-off-by: Sugizaki Yukimasa <i.can.speak.c.and.basic@gmail.com>
vcsm: Support for finding user/vc handle in memory pool
vmcs_sm_{usr,vc}_handle_from_pid_and_address() were failing to find
handle if specified user pointer is not exactly the one that the memory
locking call returned even if the pointer is in range of map/resource.
So fixed the functions to match the range.
Signed-off-by: Sugizaki Yukimasa <i.can.speak.c.and.basic@gmail.com>
vcsm: Unify cache manipulating functions
Signed-off-by: Sugizaki Yukimasa <i.can.speak.c.and.basic@gmail.com>
vcsm: Fix obscure conditions
Signed-off-by: Sugizaki Yukimasa <i.can.speak.c.and.basic@gmail.com>
vcsm: Fix memory leaking on clean_invalid2 ioctl handler
Signed-off-by: Sugizaki Yukimasa <i.can.speak.c.and.basic@gmail.com>
vcsm: Describe the use of cache operation constants
Signed-off-by: Sugizaki Yukimasa <i.can.speak.c.and.basic@gmail.com>
vcsm: Fix obscure conditions again
Signed-off-by: Sugizaki Yukimasa <i.can.speak.c.and.basic@gmail.com>
vcsm: Add no-op cache operation constant
Signed-off-by: Sugizaki Yukimasa <i.can.speak.c.and.basic@gmail.com>
vcsm: Revert to do page-table-walk-based cache manipulating on some ioctl calls
On FLUSH, INVALID, CLEAN_INVALID ioctl calls, cache operations based on
page table walk were used in case that the buffer of the cache is not
pinned. So reverted to do page-table-based cache manipulating.
Signed-off-by: Sugizaki Yukimasa <i.can.speak.c.and.basic@gmail.com>
vcsm: Define cache operation constants in user header
Without this change, users have to use raw values (1, 2, 3) to specify
cache operation.
Signed-off-by: Sugizaki Yukimasa <i.can.speak.c.and.basic@gmail.com>
Signed-off-by: popcornmix <popcornmix@gmail.com>
BCM270x: Move vc_mem
Make the vc_mem module available for ARCH_BCM2835 by moving it.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM2835 has two SD card interfaces. This driver uses the other one.
bcm2835-sdhost: Error handling fix, and code clarification
bcm2835-sdhost: Adding overclocking option
Allow a different clock speed to be substitued for a requested 50MHz.
This option is exposed using the "overclock_50" DT parameter.
Note that the sdhost interface is restricted to integer divisions of
core_freq, and the highest sensible option for a core_freq of 250MHz
is 84 (250/3 = 83.3MHz), the next being 125 (250/2) which is much too
high.
Use at your own risk.
bcm2835-sdhost: Round up the overclock, so 62 works for 62.5Mhz
Also only warn once for each overclock setting.
bcm2835-sdhost: Improve error handling and recovery
1) Expose the hw_reset method to the MMC framework, removing many
internal calls by the driver.
2) Reduce overclock setting on error.
3) Increase timeout to cope with high capacity cards.
4) Add properties and parameters to control pio_limit and debug.
5) Reduce messages at probe time.
bcm2835-sdhost: Further improve overclock back-off
bcm2835-sdhost: Clear HBLC for PIO mode
Also update pio_limit default in overlay README.
bcm2835-sdhost: Add the ERASE capability
See: https://github.com/raspberrypi/linux/issues/1076
bcm2835-sdhost: Ignore CRC7 for MMC CMD1
It seems that the sdhost interface returns CRC7 errors for CMD1,
which is the MMC-specific SEND_OP_COND. Returning these errors to
the MMC layer causes a downward spiral, but ignoring them seems
to be harmless.
bcm2835-mmc/sdhost: Remove ARCH_BCM2835 differences
The bcm2835-mmc driver (and -sdhost driver that copied from it)
contains code to handle SDIO interrupts in a threaded interrupt
handler rather than waking the MMC framework thread. The change
follows a patch from Russell King that adds the facility as the
preferred way of working.
However, the new code path is only present in ARCH_BCM2835
builds, which I have taken to be a way of testing the waters
rather than making the change across the board; I can't see
any technical reason why it wouldn't be enabled for MACH_BCM270X
builds. So this patch standardises on the ARCH_BCM2835 code,
removing the old code paths.
bcm2835-sdhost: Don't log timeout errors unless debug=1
The MMC card-discovery process generates timeouts. This is
expected behaviour, so reporting it to the user serves no purpose.
Suppress the reporting of timeout errors unless the debug flag
is on.
bcm2835-sdhost: Add workaround for odd behaviour on some cards
For reasons not understood, the sdhost driver fails when reading
sectors very near the end of some SD cards. The problem could
be related to the similar issue that reading the final sector
of any card as part of a multiple read never completes, and the
workaround is an extension of the mechanism introduced to solve
that problem which ensures those sectors are always read singly.
bcm2835-sdhost: Major revision
This is a significant revision of the bcm2835-sdhost driver. It
improves on the original in a number of ways:
1) Through the use of CMD23 for reads it appears to avoid problems
reading some sectors on certain high speed cards.
2) Better atomicity to prevent crashes.
3) Higher performance.
4) Activity logging included, for easier diagnosis in the event
of a problem.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Restore ATOMIC flag to PIO sg mapping
Allocation problems have been seen in a wireless driver, and
this is the only change which might have been responsible.
SQUASH: bcm2835-sdhost: Only claim one DMA channel
With both MMC controllers enabled there are few DMA channels left. The
bcm2835-sdhost driver only uses DMA in one direction at a time, so it
doesn't need to claim two channels.
See: https://github.com/raspberrypi/linux/issues/1327
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Workaround for "slow" sectors
Some cards have been seen to cause timeouts after certain sectors are
read. This workaround enforces a minimum delay between the stop after
reading one of those sectors and a subsequent data command.
Using CMD23 (SET_BLOCK_COUNT) avoids this problem, so good cards will
not be penalised by this workaround.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Firmware manages the clock divisor
The bcm2835-sdhost driver hands control of the CDIV clock divisor
register to matching firmware, allowing it to adjust to a changing
core clock. This removes the need to use the performance governor or
to enable io_is_busy on the on-demand governor in order to get the
best SD performance.
N.B. As SD clocks must be an integer divisor of the core clock, it is
possible that the SD clock for "turbo" mode can be different (even
lower) than "normal" mode.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Reset the clock in task context
Since reprogramming the clock can now involve a round-trip to the
firmware it must not be done at atomic context, and a tasklet
is not a task.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Don't exit cmd wait loop on error
The FAIL flag can be set in the CMD register before command processing
is complete, leading to spurious "failed to complete" errors. This has
the effect of promoting harmless CRC7 errors during CMD1 processing
into errors that can delay and even prevent booting.
Also:
1) Convert the last KERN_ERROR message in the register dumping to
KERN_INFO.
2) Remove an unnecessary reset call from bcm2835_sdhost_add_host.
See: https://github.com/raspberrypi/linux/pull/1492
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: mmc_card_blockaddr fix
Get the definition of mmc_card_blockaddr from drivers/mmc/core/card.h.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: New timer API
mmc: bcm2835-sdhost: Support underclocking
Support underclocking of the SD bus in two ways:
1. using the max-frequency DT property (which currently has no DT
parameter), and
2. using the exiting sd_overclock parameter.
The two methods differ slightly - in the former the MMC subsystem is
aware of the underclocking, while in the latter it isn't - but the
end results should be the same.
See: https://github.com/raspberrypi/linux/issues/2350
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
mmc: bcm2835-sdhost: Add include
highmem.h (needed for kmap_atomic) is pulled in by one of the other
include files, but only with some CONFIG settings. Make the inclusion
explicit to cater for cases where the CONFIG setting is absent.
See: https://github.com/raspberrypi/linux/issues/2366
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
mmc: Disable CMD23 transfers on all cards
Pending wire-level investigation of these types of transfers
and associated errors on bcm2835-mmc, disable for now. Fallback of
CMD18/CMD25 transfers will be used automatically by the MMC layer.
Reported/Tested-by: Gellert Weisz <gellert@raspberrypi.org>
mmc: bcm2835-mmc: enable DT support for all architectures
Both ARCH_BCM2835 and ARCH_BCM270x are built with OF now.
Enable Device Tree support for all architectures.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
mmc: bcm2835-mmc: fix probe error handling
Probe error handling is broken in several places.
Simplify error handling by using device managed functions.
Replace pr_{err,info} with dev_{err,info}.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2835-mmc: Add locks when accessing sdhost registers
bcm2835-mmc: Add range of debug options for slowing things down
bcm2835-mmc: Add option to disable some delays
bcm2835-mmc: Add option to disable MMC_QUIRK_BLK_NO_CMD23
bcm2835-mmc: Default to disabling MMC_QUIRK_BLK_NO_CMD23
bcm2835-mmc: Adding overclocking option
Allow a different clock speed to be substitued for a requested 50MHz.
This option is exposed using the "overclock_50" DT parameter.
Note that the mmc interface is restricted to EVEN integer divisions of
250MHz, and the highest sensible option is 63 (250/4 = 62.5), the
next being 125 (250/2) which is much too high.
Use at your own risk.
bcm2835-mmc: Round up the overclock, so 62 works for 62.5Mhz
Also only warn once for each overclock setting.
mmc: bcm2835-mmc: Make available on ARCH_BCM2835
Make the bcm2835-mmc driver available for use on ARCH_BCM2835.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270x_DT: add bcm2835-mmc entry
Add Device Tree entry for bcm2835-mmc.
In non-DT mode, don't add the device in the board file.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2835-mmc: Don't overwrite MMC capabilities from DT
bcm2835-mmc: Don't override bus width capabilities from devicetree
Take out the force setting of the MMC_CAP_4_BIT_DATA host capability
so that the result read from devicetree via mmc_of_parse() is
preserved.
bcm2835-mmc: Only claim one DMA channel
With both MMC controllers enabled there are few DMA channels left. The
bcm2835-mmc driver only uses DMA in one direction at a time, so it
doesn't need to claim two channels.
See: https://github.com/raspberrypi/linux/issues/1327
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-mmc: New timer API
mmc: bcm2835-mmc: Support underclocking
Support underclocking of the SD bus using the max-frequency DT property
(which currently has no DT parameter). The sd_overclock parameter
already provides another way to achieve the same thing which should be
equivalent in end result, but it is a bug not to support max-frequency
as well.
See: https://github.com/raspberrypi/linux/issues/2350
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Add support for DMA controller of BCM2708 as used in the Raspberry Pi.
Currently it only supports cyclic DMA.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
dmaengine: expand functionality by supporting scatter/gather transfers sdhci-bcm2708 and dma.c: fix for LITE channels
DMA: fix cyclic LITE length overflow bug
dmaengine: bcm2708: Remove chancnt affectations
Mirror bcm2835-dma.c commit 9eba5536a7:
chancnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: overwrite dreq only if it is not set
dreq is set when the DMA channel is fetched from Device Tree.
slave_id is set using dmaengine_slave_config().
Only overwrite dreq with slave_id if it is not set.
dreq/slave_id in the cyclic DMA case is not touched, because I don't
have hardware to test with.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: do device registration in the board file
Don't register the device in the driver. Do it in the board file.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: don't restrict DT support to ARCH_BCM2835
Both ARCH_BCM2835 and ARCH_BCM270x are built with OF now.
Add Device Tree support to the non ARCH_BCM2835 case.
Use the same driver name regardless of architecture.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270x_DT: add bcm2835-dma entry
Add Device Tree entry for bcm2835-dma.
The entry doesn't contain any resources since they are handled
by the arch/arm/mach-bcm270x/dma.c driver.
In non-DT mode, don't add the device in the board file.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2708-dmaengine: Add debug options
BCM270x: Add memory and irq resources to dmaengine device and DT
Prepare for merging of the legacy DMA API arch driver dma.c
with bcm2708-dmaengine by adding memory and irq resources both
to platform file device and Device Tree node.
Don't use BCM_DMAMAN_DRIVER_NAME so we don't have to include mach/dma.h
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: Merge with arch dma.c driver and disable dma.c
Merge the legacy DMA API driver with bcm2708-dmaengine.
This is done so we can use bcm2708_fb on ARCH_BCM2835 (mailbox
driver is also needed).
Changes to the dma.c code:
- Use BIT() macro.
- Cutdown some comments to one line.
- Add mutex to vc_dmaman and use this, since the dev lock is locked
during probing of the engine part.
- Add global g_dmaman variable since drvdata is used by the engine part.
- Restructure for readability:
vc_dmaman_chan_alloc()
vc_dmaman_chan_free()
bcm_dma_chan_free()
- Restructure bcm_dma_chan_alloc() to simplify error handling.
- Use device irq resources instead of hardcoded bcm_dma_irqs table.
- Remove dev_dmaman_register() and code it directly.
- Remove dev_dmaman_deregister() and code it directly.
- Simplify bcm_dmaman_probe() using devm_* functions.
- Get dmachans from DT if available.
- Keep 'dma.dmachans' module argument name for backwards compatibility.
Make it available on ARCH_BCM2835 as well.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: set residue_granularity field
bcm2708-dmaengine supports residue reporting at burst level
but didn't report this via the residue_granularity field.
Without this field set properly we get playback issues with I2S cards.
dmaengine: bcm2708-dmaengine: Fix memory leak when stopping a running transfer
bcm2708-dmaengine: Use more DMA channels (but not 12)
1) Only the bcm2708_fb drivers uses the legacy DMA API, and
it requires a BULK-capable channel, so all other types
(FAST, NORMAL and LITE) can be made available to the regular
DMA API.
2) DMA channels 11-14 share an interrupt. The driver can't
handle this, so don't use channels 12-14 (12 was used, probably
because it appears to have an interrupt, but in reality that
interrupt is for activity on ANY channel). This may explain
a lockup encountered when running out of DMA channels.
The combined effect of this patch is to leave 7 DMA channels
available + channel 0 for bcm2708_fb via the legacy API.
See: https://github.com/raspberrypi/linux/issues/1110https://github.com/raspberrypi/linux/issues/1108
dmaengine: bcm2708: Make legacy API available for bcm2835-dma
bcm2708_fb uses the legacy DMA API, so in order to start using
bcm2835-dma, bcm2835-dma has to support the legacy API. Make this
possible by exporting bcm_dmaman_probe() and bcm_dmaman_remove().
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: Change DT compatible string
Both bcm2835-dma and bcm2708-dmaengine have the same compatible string.
So change compatible to "brcm,bcm2708-dma".
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: Remove driver but keep legacy API
Dropping non-DT support means we don't need this driver,
but we still need the legacy DMA API.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2708-dmaengine - Fix arm64 portability/build issues
dma-bcm2708: Fix module compilation of CONFIG_DMA_BCM2708
bcm2708-dmaengine.c defines functions like bcm_dma_start which are
defined as well in dma-bcm2708.h as inline versions when
CONFIG_DMA_BCM2708 is not defined. This works fine when
CONFIG_DMA_BCM2708 is built in, but when it is selected as module build
fails with redefinition errors because in the build system when
CONFIG_DMA_BCM2708 is selected as module, the macro becomes
CONFIG_DMA_BCM2708_MODULE.
This patch makes the header use CONFIG_DMA_BCM2708_MODULE too when
available.
Fixes https://github.com/raspberrypi/linux/issues/2056
Signed-off-by: Andrei Gherzan <andrei@gherzan.com>
Especially on platforms with a slower CPU but a relatively high
framebuffer fill bandwidth, like current ARM devices, the existing
console monochrome imageblit function used to draw console text is
suboptimal for common pixel depths such as 16bpp and 32bpp. The existing
code is quite general and can deal with several pixel depths. By creating
special case functions for 16bpp and 32bpp, by far the most common pixel
formats used on modern systems, a significant speed-up is attained
which can be readily felt on ARM-based devices like the Raspberry Pi
and the Allwinner platform, but should help any platform using the
fb layer.
The special case functions allow constant folding, eliminating a number
of instructions including divide operations, and allow the use of an
unrolled loop, eliminating instructions with a variable shift size,
reducing source memory access instructions, and eliminating excessive
branching. These unrolled loops also allow much better code optimization
by the C compiler. The code that selects which optimized variant is used
is also simplified, eliminating integer divide instructions.
The speed-up, measured by timing 'cat file.txt' in the console, varies
between 40% and 70%, when testing on the Raspberry Pi and Allwinner
ARM-based platforms, depending on font size and the pixel depth, with
the greater benefit for 32bpp.
Signed-off-by: Harm Hanemaaijer <fgenfb@yahoo.com>
Signed-off-by: popcornmix <popcornmix@gmail.com>
bcm2708_fb : Implement blanking support using the mailbox property interface
bcm2708_fb: Add pan and vsync controls
bcm2708_fb: DMA acceleration for fb_copyarea
Based on http://www.raspberrypi.org/phpBB3/viewtopic.php?p=62425#p62425
Also used Simon's dmaer_master module as a reference for tweaking DMA
settings for better performance.
For now busylooping only. IRQ support might be added later.
With non-overclocked Raspberry Pi, the performance is ~360 MB/s
for simple copy or ~260 MB/s for two-pass copy (used when dragging
windows to the right).
In the case of using DMA channel 0, the performance improves
to ~440 MB/s.
For comparison, VFP optimized CPU copy can only do ~114 MB/s in
the same conditions (hindered by reading uncached source buffer).
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
bcm2708_fb: report number of dma copies
Add a counter (exported via debugfs) reporting the
number of dma copies that the framebuffer driver
has done, in order to help evaluate different
optimization strategies.
Signed-off-by: Luke Diamand <luked@broadcom.com>
bcm2708_fb: use IRQ for DMA copies
The copyarea ioctl() uses DMA to speed things along. This
was busy-waiting for completion. This change supports using
an interrupt instead for larger transfers. For small
transfers, busy-waiting is still likely to be faster.
Signed-off-by: Luke Diamand <luke@diamand.org>
bcm2708: Make ioctl logging quieter
video: fbdev: bcm2708_fb: Don't panic on error
No need to panic the kernel if the video driver fails.
Just print a message and return an error.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
fbdev: bcm2708_fb: Add ARCH_BCM2835 support
Add Device Tree support.
Pass the device to dma_alloc_coherent() in order to get the
correct bus address on ARCH_BCM2835.
Use the new DMA legacy API header file.
Including <mach/platform.h> is not necessary.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270x_DT: Add bcm2708-fb device
Add bcm2708-fb to Device Tree and don't add the
platform device when booting in DT mode.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Cleanup of bcm2708_fb file to kernel coding standards
Some minor change to function - remove a use of
in_atomic, plus replacing various debug messages
that manually specify the function name with
("%s",.__func__)
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
Signed-off-by: popcornmix <popcornmix@gmail.com>
usb: dwc: fix lockdep false positive
Signed-off-by: Kari Suvanto <karis79@gmail.com>
usb: dwc: fix inconsistent lock state
Signed-off-by: Kari Suvanto <karis79@gmail.com>
Add FIQ patch to dwc_otg driver. Enable with dwc_otg.fiq_fix_enable=1. Should give about 10% more ARM performance.
Thanks to Gordon and Costas
Avoid dynamic memory allocation for channel lock in USB driver. Thanks ddv2005.
Add NAK holdoff scheme. Enabled by default, disable with dwc_otg.nak_holdoff_enable=0. Thanks gsh
Make sure we wait for the reset to finish
dwc_otg: fix bug in dwc_otg_hcd.c resulting in silent kernel
memory corruption, escalating to OOPS under high USB load.
dwc_otg: Fix unsafe access of QTD during URB enqueue
In dwc_otg_hcd_urb_enqueue during qtd creation, it was possible that the
transaction could complete almost immediately after the qtd was assigned
to a host channel during URB enqueue, which meant the qtd pointer was no
longer valid having been completed and removed. Usually, this resulted in
an OOPS during URB submission. By predetermining whether transactions
need to be queued or not, this unsafe pointer access is avoided.
This bug was only evident on the Pi model A where a device was attached
that had no periodic endpoints (e.g. USB pendrive or some wlan devices).
dwc_otg: Fix incorrect URB allocation error handling
If the memory allocation for a dwc_otg_urb failed, the kernel would OOPS
because for some reason a member of the *unallocated* struct was set to
zero. Error handling changed to fail correctly.
dwc_otg: fix potential use-after-free case in interrupt handler
If a transaction had previously aborted, certain interrupts are
enabled to track error counts and reset where necessary. On IN
endpoints the host generates an ACK interrupt near-simultaneously
with completion of transfer. In the case where this transfer had
previously had an error, this results in a use-after-free on
the QTD memory space with a 1-byte length being overwritten to
0x00.
dwc_otg: add handling of SPLIT transaction data toggle errors
Previously a data toggle error on packets from a USB1.1 device behind
a TT would result in the Pi locking up as the driver never handled
the associated interrupt. Patch adds basic retry mechanism and
interrupt acknowledgement to cater for either a chance toggle error or
for devices that have a broken initial toggle state (FT8U232/FT232BM).
dwc_otg: implement tasklet for returning URBs to usbcore hcd layer
The dwc_otg driver interrupt handler for transfer completion will spend
a very long time with interrupts disabled when a URB is completed -
this is because usb_hcd_giveback_urb is called from within the handler
which for a USB device driver with complicated processing (e.g. webcam)
will take an exorbitant amount of time to complete. This results in
missed completion interrupts for other USB packets which lead to them
being dropped due to microframe overruns.
This patch splits returning the URB to the usb hcd layer into a
high-priority tasklet. This will have most benefit for isochronous IN
transfers but will also have incidental benefit where multiple periodic
devices are active at once.
dwc_otg: fix NAK holdoff and allow on split transactions only
This corrects a bug where if a single active non-periodic endpoint
had at least one transaction in its qh, on frnum == MAX_FRNUM the qh
would get skipped and never get queued again. This would result in
a silent device until error detection (automatic or otherwise) would
either reset the device or flush and requeue the URBs.
Additionally the NAK holdoff was enabled for all transactions - this
would potentially stall a HS endpoint for 1ms if a previous error state
enabled this interrupt and the next response was a NAK. Fix so that
only split transactions get held off.
dwc_otg: Call usb_hcd_unlink_urb_from_ep with lock held in completion handler
usb_hcd_unlink_urb_from_ep must be called with the HCD lock held. Calling it
asynchronously in the tasklet was not safe (regression in
c4564d4a1a).
This change unlinks it from the endpoint prior to queueing it for handling in
the tasklet, and also adds a check to ensure the urb is OK to be unlinked
before doing so.
NULL pointer dereference kernel oopses had been observed in usb_hcd_giveback_urb
when a USB device was unplugged/replugged during data transfer. This effect
was reproduced using automated USB port power control, hundreds of replug
events were performed during active transfers to confirm that the problem was
eliminated.
USB fix using a FIQ to implement split transactions
This commit adds a FIQ implementaion that schedules
the split transactions using a FIQ so we don't get
held off by the interrupt latency of Linux
dwc_otg: fix device attributes and avoid kernel warnings on boot
dcw_otg: avoid logging function that can cause panics
See: https://github.com/raspberrypi/firmware/issues/21
Thanks to cleverca22 for fix
dwc_otg: mask correct interrupts after transaction error recovery
The dwc_otg driver will unmask certain interrupts on a transaction
that previously halted in the error state in order to reset the
QTD error count. The various fine-grained interrupt handlers do not
consider that other interrupts besides themselves were unmasked.
By disabling the two other interrupts only ever enabled in DMA mode
for this purpose, we can avoid unnecessary function calls in the
IRQ handler. This will also prevent an unneccesary FIQ interrupt
from being generated if the FIQ is enabled.
dwc_otg: fiq: prevent FIQ thrash and incorrect state passing to IRQ
In the case of a transaction to a device that had previously aborted
due to an error, several interrupts are enabled to reset the error
count when a device responds. This has the side-effect of making the
FIQ thrash because the hardware will generate multiple instances of
a NAK on an IN bulk/interrupt endpoint and multiple instances of ACK
on an OUT bulk/interrupt endpoint. Make the FIQ mask and clear the
associated interrupts.
Additionally, on non-split transactions make sure that only unmasked
interrupts are cleared. This caused a hard-to-trigger but serious
race condition when you had the combination of an endpoint awaiting
error recovery and a transaction completed on an endpoint - due to
the sequencing and timing of interrupts generated by the dwc_otg core,
it was possible to confuse the IRQ handler.
Fix function tracing
dwc_otg: whitespace cleanup in dwc_otg_urb_enqueue
dwc_otg: prevent OOPSes during device disconnects
The dwc_otg_urb_enqueue function is thread-unsafe. In particular the
access of urb->hcpriv, usb_hcd_link_urb_to_ep, dwc_otg_urb->qtd and
friends does not occur within a critical section and so if a device
was unplugged during activity there was a high chance that the
usbcore hub_thread would try to disable the endpoint with partially-
formed entries in the URB queue. This would result in BUG() or null
pointer dereferences.
Fix so that access of urb->hcpriv, enqueuing to the hardware and
adding to usbcore endpoint URB lists is contained within a single
critical section.
dwc_otg: prevent BUG() in TT allocation if hub address is > 16
A fixed-size array is used to track TT allocation. This was
previously set to 16 which caused a crash because
dwc_otg_hcd_allocate_port would read past the end of the array.
This was hit if a hub was plugged in which enumerated as addr > 16,
due to previous device resets or unplugs.
Also add #ifdef FIQ_DEBUG around hcd->hub_port_alloc[], which grows
to a large size if 128 hub addresses are supported. This field is
for debug only for tracking which frame an allocate happened in.
dwc_otg: make channel halts with unknown state less damaging
If the IRQ received a channel halt interrupt through the FIQ
with no other bits set, the IRQ would not release the host
channel and never complete the URB.
Add catchall handling to treat as a transaction error and retry.
dwc_otg: fiq_split: use TTs with more granularity
This fixes certain issues with split transaction scheduling.
- Isochronous multi-packet OUT transactions now hog the TT until
they are completed - this prevents hubs aborting transactions
if they get a periodic start-split out-of-order
- Don't perform TT allocation on non-periodic endpoints - this
allows simultaneous use of the TT's bulk/control and periodic
transaction buffers
This commit will mainly affect USB audio playback.
dwc_otg: fix potential sleep while atomic during urb enqueue
Fixes a regression introduced with eb1b482a. Kmalloc called from
dwc_otg_hcd_qtd_add / dwc_otg_hcd_qtd_create did not always have
the GPF_ATOMIC flag set. Force this flag when inside the larger
critical section.
dwc_otg: make fiq_split_enable imply fiq_fix_enable
Failing to set up the FIQ correctly would result in
"IRQ 32: nobody cared" errors in dmesg.
dwc_otg: prevent crashes on host port disconnects
Fix several issues resulting in crashes or inconsistent state
if a Model A root port was disconnected.
- Clean up queue heads properly in kill_urbs_in_qh_list by
removing the empty QHs from the schedule lists
- Set the halt status properly to prevent IRQ handlers from
using freed memory
- Add fiq_split related cleanup for saved registers
- Make microframe scheduling reclaim host channels if
active during a disconnect
- Abort URBs with -ESHUTDOWN status response, informing
device drivers so they respond in a more correct fashion
and don't try to resubmit URBs
- Prevent IRQ handlers from attempting to handle channel
interrupts if the associated URB was dequeued (and the
driver state was cleared)
dwc_otg: prevent leaking URBs during enqueue
A dwc_otg_urb would get leaked if the HCD enqueue function
failed for any reason. Free the URB at the appropriate points.
dwc_otg: Enable NAK holdoff for control split transactions
Certain low-speed devices take a very long time to complete a
data or status stage of a control transaction, producing NAK
responses until they complete internal processing - the USB2.0
spec limit is up to 500mS. This causes the same type of interrupt
storm as seen with USB-serial dongles prior to c8edb238.
In certain circumstances, usually while booting, this interrupt
storm could cause SD card timeouts.
dwc_otg: Fix for occasional lockup on boot when doing a USB reset
dwc_otg: Don't issue traffic to LS devices in FS mode
Issuing low-speed packets when the root port is in full-speed mode
causes the root port to stop responding. Explicitly fail when
enqueuing URBs to a LS endpoint on a FS bus.
Fix ARM architecture issue with local_irq_restore()
If local_fiq_enable() is called before a local_irq_restore(flags) where
the flags variable has the F bit set, the FIQ will be erroneously disabled.
Fixup arch_local_irq_restore to avoid trampling the F bit in CPSR.
Also fix some of the hacks previously implemented for previous dwc_otg
incarnations.
dwc_otg: fiq_fsm: Base commit for driver rewrite
This commit removes the previous FIQ fixes entirely and adds fiq_fsm.
This rewrite features much more complete support for split transactions
and takes into account several OTG hardware bugs. High-speed
isochronous transactions are also capable of being performed by fiq_fsm.
All driver options have been removed and replaced with:
- dwc_otg.fiq_enable (bool)
- dwc_otg.fiq_fsm_enable (bool)
- dwc_otg.fiq_fsm_mask (bitmask)
- dwc_otg.nak_holdoff (unsigned int)
Defaults are specified such that fiq_fsm behaves similarly to the
previously implemented FIQ fixes.
fiq_fsm: Push error recovery into the FIQ when fiq_fsm is used
If the transfer associated with a QTD failed due to a bus error, the HCD
would retry the transfer up to 3 times (implementing the USB2.0
three-strikes retry in software).
Due to the masking mechanism used by fiq_fsm, it is only possible to pass
a single interrupt through to the HCD per-transfer.
In this instance host channels would fall off the radar because the error
reset would function, but the subsequent channel halt would be lost.
Push the error count reset into the FIQ handler.
fiq_fsm: Implement timeout mechanism
For full-speed endpoints with a large packet size, interrupt latency
runs the risk of the FIQ starting a transaction too late in a full-speed
frame. If the device is still transmitting data when EOF2 for the
downstream frame occurs, the hub will disable the port. This change is
not reflected in the hub status endpoint and the device becomes
unresponsive.
Prevent high-bandwidth transactions from being started too late in a
frame. The mechanism is not guaranteed: a combination of bit stuffing
and hub latency may still result in a device overrunning.
fiq_fsm: fix bounce buffer utilisation for Isochronous OUT
Multi-packet isochronous OUT transactions were subject to a few bounday
bugs. Fix them.
Audio playback is now much more robust: however, an issue stands with
devices that have adaptive sinks - ALSA plays samples too fast.
dwc_otg: Return full-speed frame numbers in HS mode
The frame counter increments on every *microframe* in high-speed mode.
Most device drivers expect this number to be in full-speed frames - this
caused considerable confusion to e.g. snd_usb_audio which uses the
frame counter to estimate the number of samples played.
fiq_fsm: save PID on completion of interrupt OUT transfers
Also add edge case handling for interrupt transports.
Note that for periodic split IN, data toggles are unimplemented in the
OTG host hardware - it unconditionally accepts any PID.
fiq_fsm: add missing case for fiq_fsm_tt_in_use()
Certain combinations of bitrate and endpoint activity could
result in a periodic transaction erroneously getting started
while the previous Isochronous OUT was still active.
fiq_fsm: clear hcintmsk for aborted transactions
Prevents the FIQ from erroneously handling interrupts
on a timed out channel.
fiq_fsm: enable by default
fiq_fsm: fix dequeues for non-periodic split transactions
If a dequeue happened between the SSPLIT and CSPLIT phases of the
transaction, the HCD would never receive an interrupt.
fiq_fsm: Disable by default
fiq_fsm: Handle HC babble errors
The HCTSIZ transfer size field raises a babble interrupt if
the counter wraps. Handle the resulting interrupt in this case.
dwc_otg: fix interrupt registration for fiq_enable=0
Additionally make the module parameter conditional for wherever
hcd->fiq_state is touched.
fiq_fsm: Enable by default
dwc_otg: Fix various issues with root port and transaction errors
Process the host port interrupts correctly (and don't trample them).
Root port hotplug now functional again.
Fix a few thinkos with the transaction error passthrough for fiq_fsm.
fiq_fsm: Implement hack for Split Interrupt transactions
Hubs aren't too picky about which endpoint we send Control type split
transactions to. By treating Interrupt transfers as Control, it is
possible to use the non-periodic queue in the OTG core as well as the
non-periodic FIFOs in the hub itself. This massively reduces the
microframe exclusivity/contention that periodic split transactions
otherwise have to enforce.
It goes without saying that this is a fairly egregious USB specification
violation, but it works.
Original idea by Hans Petter Selasky @ FreeBSD.org.
dwc_otg: FIQ support on SMP. Set up FIQ stack and handler on Core 0 only.
dwc_otg: introduce fiq_fsm_spin(un|)lock()
SMP safety for the FIQ relies on register read-modify write cycles being
completed in the correct order. Several places in the DWC code modify
registers also touched by the FIQ. Protect these by a bare-bones lock
mechanism.
This also makes it possible to run the FIQ and IRQ handlers on different
cores.
fiq_fsm: fix build on bcm2708 and bcm2709 platforms
dwc_otg: put some barriers back where they should be for UP
bcm2709/dwc_otg: Setup FIQ on core 1 if >1 core active
dwc_otg: fixup read-modify-write in critical paths
Be more careful about read-modify-write on registers that the FIQ
also touches.
Guard fiq_fsm_spin_lock with fiq_enable check
fiq_fsm: Falling out of the state machine isn't fatal
This edge case can be hit if the port is disabled while the FIQ is
in the middle of a transaction. Make the effects less severe.
Also get rid of the useless return value.
squash: dwc_otg: Allow to build without SMP
usb: core: make overcurrent messages more prominent
Hub overcurrent messages are more serious than "debug". Increase loglevel.
usb: dwc_otg: Don't use dma_to_virt()
Commit 6ce0d20 changes dma_to_virt() which breaks this driver.
Open code the old dma_to_virt() implementation to work around this.
Limit the use of __bus_to_virt() to cases where transfer_buffer_length
is set and transfer_buffer is not set. This is done to increase the
chance that this driver will also work on ARCH_BCM2835.
transfer_buffer should not be NULL if the length is set, but the
comment in the code indicates that there are situations where this
might happen. drivers/usb/isp1760/isp1760-hcd.c also has a similar
comment pointing to a possible: 'usb storage / SCSI bug'.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: Fix crash when fiq_enable=0
dwc_otg: fiq_fsm: Make high-speed isochronous strided transfers work properly
Certain low-bandwidth high-speed USB devices (specialist audio devices,
compressed-frame webcams) have packet intervals > 1 microframe.
Stride these transfers in the FIQ by using the start-of-frame interrupt
to restart the channel at the right time.
dwc_otg: Force host mode to fix incorrect compute module boards
dwc_otg: Add ARCH_BCM2835 support
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: Simplify FIQ irq number code
Dropping ATAGS means we can simplify the FIQ irq number code.
Also add error checking on the returned irq number.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: Remove duplicate gadget probe/unregister function
dwc_otg: Properly set the HFIR
Douglas Anderson reported:
According to the most up to date version of the dwc2 databook, the FRINT
field of the HFIR register should be programmed to:
* 125 us * (PHY clock freq for HS) - 1
* 1000 us * (PHY clock freq for FS/LS) - 1
This is opposed to older versions of the doc that claimed it should be:
* 125 us * (PHY clock freq for HS)
* 1000 us * (PHY clock freq for FS/LS)
and reported lower timing jitter on a USB analyser
dcw_otg: trim xfer length when buffer larger than allocated size is received
dwc_otg: Don't free qh align buffers in atomic context
dwc_otg: Enable the hack for Split Interrupt transactions by default
dwc_otg.fiq_fsm_mask=0xF has long been a suggestion for users with audio stutters or other USB bandwidth issues.
So far we are aware of many success stories but no failure caused by this setting.
Make it a default to learn more.
See: https://www.raspberrypi.org/forums/viewtopic.php?f=28&t=70437
Signed-off-by: popcornmix <popcornmix@gmail.com>
dwc_otg: Use kzalloc when suitable
dwc_otg: Pass struct device to dma_alloc*()
This makes it possible to get the bus address from Device Tree.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: fix summarize urb->actual_length for isochronous transfers
Kernel does not copy input data of ISO transfers to userspace
if actual_length is set only in ISO transfers and not summarized
in urb->actual_length. Fixesraspberrypi/linux#903
fiq_fsm: Use correct states when starting isoc OUT transfers
In fiq_fsm_start_next_periodic() if an isochronous OUT transfer
was selected, no regard was given as to whether this was a single-packet
transfer or a multi-packet staged transfer.
For single-packet transfers, this had the effect of repeatedly sending
OUT packets with bogus data and lengths.
Eventually if the channel was repeatedly enabled enough times, this
would lock up the OTG core and no further bus transfers would happen.
Set the FSM state up properly if we select a single-packet transfer.
Fixes https://github.com/raspberrypi/linux/issues/1842
dwc_otg: make nak_holdoff work as intended with empty queues
If URBs reading from non-periodic split endpoints were dequeued and
the last transfer from the endpoint was a NAK handshake, the resulting
qh->nak_frame value was stale which would result in unnecessarily long
polling intervals for the first subsequent transfer with a fresh URB.
Fixup qh->nak_frame in dwc_otg_hcd_urb_dequeue and also guard against
a case where a single URB is submitted to the endpoint, a NAK was
received on the transfer immediately prior to receiving data and the
device subsequently resubmits another URB past the qh->nak_frame interval.
Fixes https://github.com/raspberrypi/linux/issues/1709
dwc_otg: fix split transaction data toggle handling around dequeues
See https://github.com/raspberrypi/linux/issues/1709
Fix several issues regarding endpoint state when URBs are dequeued
- If the HCD is disconnected, flush FIQ-enabled channels properly
- Save the data toggle state for bulk endpoints if the last transfer
from an endpoint where URBs were dequeued returned a data packet
- Reset hc->start_pkt_count properly in assign_and_init_hc()
dwc_otg: fix several potential crash sources
On root port disconnect events, the host driver state is cleared and
in-progress host channels are forcibly stopped. This doesn't play
well with the FIQ running in the background, so:
- Guard the disconnect callback with both the host spinlock and FIQ
spinlock
- Move qtd dereference in dwc_otg_handle_hc_fsm() after the early-out
so we don't dereference a qtd that has gone away
- Turn catch-all BUG()s in dwc_otg_handle_hc_fsm() into warnings.
dwc_otg: delete hcd->channel_lock
The lock serves no purpose as it is only held while the HCD spinlock
is already being held.
dwc_otg: remove unnecessary dma-mode channel halts on disconnect interrupt
Host channels are already halted in kill_urbs_in_qh_list() with the
subsequent interrupt processing behaving as if the URB was dequeued
via HCD callback.
There's no need to clobber the host channel registers a second time
as this exposes races between the driver and host channel resulting
in hcd->free_hc_list becoming corrupted.
dwcotg: Allow to build without FIQ on ARM64
Signed-off-by: popcornmix <popcornmix@gmail.com>
dwc_otg: make periodic scheduling behave properly for FS buses
If the root port is in full-speed mode, transfer times at 12mbit/s
would be calculated but matched against high-speed quotas.
Reinitialise hcd->frame_usecs[i] on each port enable event so that
full-speed bandwidth can be tracked sensibly.
Also, don't bother using the FIQ for transfers when in full-speed
mode - at the slower bus speed, interrupt frequency is reduced by
an order of magnitude.
Related issue: https://github.com/raspberrypi/linux/issues/2020
dwc_otg: fiq_fsm: Make isochronous compatibility checks work properly
Get rid of the spammy printk and local pointer mangling.
Also, there is a nominal benefit for using fiq_fsm for isochronous
transfers in FS mode (~1.1k IRQs per second vs 2.1k IRQs per second)
so remove the root port speed check.
dwc_otg: add module parameter int_ep_interval_min
Add a module parameter (defaulting to ignored) that clamps the polling rate
of high-speed Interrupt endpoints to a minimum microframe interval.
The parameter is modifiable at runtime as it is used when activating new
endpoints (such as on device connect).
dwc_otg: fiq_fsm: Add non-periodic TT exclusivity constraints
Certain hub types do not discriminate between pipe direction (IN or OUT)
when considering non-periodic transfers. Therefore these hubs get confused
if multiple transfers are issued in different directions with the same
device address and endpoint number.
Constrain queuing non-periodic split transactions so they are performed
serially in such cases.
Related: https://github.com/raspberrypi/linux/issues/2024
dwc_otg: Fixup change to DRIVER_ATTR interface
dwc_otg: Fix compilation warnings
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
USB_DWCOTG: Disable building dwc_otg as a module (#2265)
When dwc_otg is built as a module, build will fail with the following
error:
ERROR: "DWC_TASK_HI_SCHEDULE" [drivers/usb/host/dwc_otg/dwc_otg.ko] undefined!
scripts/Makefile.modpost:91: recipe for target '__modpost' failed
make[1]: *** [__modpost] Error 1
Makefile:1199: recipe for target 'modules' failed
make: *** [modules] Error 2
Even if the error is solved by including the missing
DWC_TASK_HI_SCHEDULE function, the kernel will panic when loading
dwc_otg.
As a workaround, simply prevent user from building dwc_otg as a module
as the current kernel does not support it.
See: https://github.com/raspberrypi/linux/issues/2258
Signed-off-by: Malik Olivier Boussejra <malik@boussejra.com>
dwc_otg: New timer API
dwc_otg: Fix removed ACCESS_ONCE->READ_ONCE
dwc_otg: don't unconditionally force host mode in dwc_otg_cil_init()
Add the ability to disable force_host_mode for those that want to use
dwc_otg in both device and host modes.
dwc_otg: Fix a regression when dequeueing isochronous transfers
In 282bed95 (dwc_otg: make nak_holdoff work as intended with empty queues)
the dequeue mechanism was changed to leave FIQ-enabled transfers to run
to completion - to avoid leaving hub TT buffers with stale packets lying
around.
This broke FIQ-accelerated isochronous transfers, as this then meant that
dozens of transfers were performed after the dequeue function returned.
Restore the state machine fence for isochronous transfers.
fiq_fsm: rewind DMA pointer for OUT transactions that fail (#2288)
See: https://github.com/raspberrypi/linux/issues/2140
dwc_otg: add smp_mb() to prevent driver state corruption on boot
Occasional crashes have been seen where the FIQ code dereferences
invalid/random pointers immediately after being set up, leading to
panic on boot.
The crash occurs as the FIQ code races against hcd_init_fiq() and
the hcd_init_fiq() code races against the outstanding memory stores
from dwc_otg_hcd_init(). Use explicit barriers after touching
driver state.
usb: dwc_otg: fix memory corruption in dwc_otg driver
[Upstream commit 51b1b64917]
The move from the staging tree to the main tree exposed a
longstanding memory corruption bug in the dwc2 driver. The
reordering of the driver initialization caused the dwc2 driver
to corrupt the initialization data of the sdhci driver on the
Raspberry Pi platform, which made the bug show up.
The error is in calling to_usb_device(hsotg->dev), since ->dev
is not a member of struct usb_device. The easiest fix is to
just remove the offending code, since it is not really needed.
Thanks to Stephen Warren for tracking down the cause of this.
Reported-by: Andre Heider <a.heider@gmail.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[lukas: port from upstream dwc2 to out-of-tree dwc_otg driver]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
usb: dwb_otg: Fix unreachable switch statement warning
This warning appears with GCC 7.3.0 from toolchains.bootlin.com:
../drivers/usb/host/dwc_otg/dwc_otg_fiq_fsm.c: In function ‘fiq_fsm_update_hs_isoc’:
../drivers/usb/host/dwc_otg/dwc_otg_fiq_fsm.c:595:61: warning: statement will never be executed [-Wswitch-unreachable]
st->hctsiz_copy.b.xfersize = nrpackets * st->hcchar_copy.b.mps;
~~~~~~~~~~~~~~~~~^~~~
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: popcornmix <popcornmix@gmail.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2709: Drop platform smp and timer init code
irq-bcm2836 handles this through these functions:
bcm2835_init_local_timer_frequency()
bcm2836_arm_irqchip_smp_init()
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm270x: Use watchdog for reboot/poweroff
The watchdog driver already has support for reboot/poweroff.
Make use of this and remove the code from the platform files.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
board_bcm2835: Remove coherent dma pool increase - API has gone
It can be useful to be able to open multiple vchiq instances in a
single process. This currently fails due to a debugfs collision,
so make such a failure non-fatal.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The BCM2835 PL011 implementation seems to have a bug that can lead to a
transmission lockup if CTS changes frequently. A workaround was added to
the driver with a vendor-specific flag to enable it, but this flag is
currently not set for ARM implementations.
Add a "cts-event-workaround" property to Pi DTBs and use the presence
of that property to force the flag to be enabled in the driver.
See: https://github.com/raspberrypi/linux/issues/1280
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The pl011 register accessor functions use the _relaxed versions of the
standard readl() and writel() functions, meaning that there are no
automatic memory barriers. When polling a FIFO status register to check
for fullness, it is necessary to ensure that any outstanding writes have
completed; otherwise the flags are effectively stale, making it possible
that the next write is to a full FIFO.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The UART clock is initialised to be as close to the requested
frequency as possible without exceeding it. Now that there is a
clock manager that returns the actual frequencies, an expected
48MHz clock is reported as 47999625. If the requested baudrate
== requested clock/16, there is no headroom and the slight
reduction in actual clock rate results in failure.
Detect cases where it looks like a "round" clock was chosen and
adjust the reported clock to match that "round" value. As the
code comment says:
/*
* If increasing a clock by less than 0.1% changes it
* from ..999.. to ..000.., round up.
*/
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The pl011 driver looks for DT aliases of the form "serial<n>",
and if found uses <n> as the device ID. This can cause
/dev/ttyAMA0 to become /dev/ttyAMA1, which is confusing if the
other serial port is provided by the 8250 driver which doesn't
use the same logic.
For applications of the LAN78xx that don't have valid programmed
EEPROMs or OTPs, enabling both LEDs and auto-negotiation by default
seems reasonable.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
There is a standard mechanism for locating and using a MAC address from
the Device Tree. Use this facility in the lan78xx driver to support
applications without programmed EEPROM or OTP.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The syscon node defines a register range that duplicates that used by
the local_intc node on bcm2836/7. Since irq-bcm2835 and irq-bcm2836 are
built in and always present together (both drivers are enabled by
CONFIG_ARCH_BCM2835), it is possible to replace the syscon usage with a
global variable that simplifies the code. Doing so does lose the
locking provided by regmap, but as only one side is using the regmap
interface (irq-bcm2835 uses readl and write) there is no loss of
atomicity.
See: https://github.com/raspberrypi/firmware/issues/926
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Without a prompt string, a config setting can't be included in a
defconfig. Give CONFIG_SND_SOC_ICS43432 a prompt so that Pi soundcards
can use the driver.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
See commit dae803e165 -- the warning is
expected sometimes when using CMA. However, that commit still spams
my kernel log with these warnings.
Signed-off-by: Eric Anholt <eric@anholt.net>
This adds a debug module parameter to aid in debugging transfer issues
by printing info to the kernel log. When enabled, status values are
collected in the interrupt routine and msg info in
bcm2835_i2c_start_transfer(). This is done in a way that tries to avoid
affecting timing. Having printk in the isr can mask issues.
debug values (additive):
1: Print info on error
2: Print info on all transfers
3: Print messages before transfer is started
The value can be changed at runtime:
/sys/module/i2c_bcm2835/parameters/debug
Example output, debug=3:
[ 747.114448] bcm2835_i2c_xfer: msg(1/2) write addr=0x54, len=2 flags= [i2c1]
[ 747.114463] bcm2835_i2c_xfer: msg(2/2) read addr=0x54, len=32 flags= [i2c1]
[ 747.117809] start_transfer: msg(1/2) write addr=0x54, len=2 flags= [i2c1]
[ 747.117825] isr: remain=2, status=0x30000055 : TA TXW TXD TXE [i2c1]
[ 747.117839] start_transfer: msg(2/2) read addr=0x54, len=32 flags= [i2c1]
[ 747.117849] isr: remain=32, status=0xd0000039 : TA RXR TXD RXD [i2c1]
[ 747.117861] isr: remain=20, status=0xd0000039 : TA RXR TXD RXD [i2c1]
[ 747.117870] isr: remain=8, status=0x32 : DONE TXD RXD [i2c1]
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Christopher Alexander Tobias Schulze - May 2, 2015, 11:57 a.m.
This patch fixes a problem with VFP state save and restore related
to exception handling (panic with message "BUG: unsupported FP
instruction in kernel mode") present on VFP11 floating point units
(as used with ARM1176JZF-S CPUs, e.g. on first generation Raspberry
Pi boards). This patch was developed and discussed on
https://github.com/raspberrypi/linux/issues/859
A precondition to see the crashes is that floating point exception
traps are enabled. In this case, the VFP11 might determine that a FPU
operation needs to trap at a point in time when it is not possible to
signal this to the ARM11 core any more. The VFP11 will then set the
FPEXC.EX bit and store the trapped opcode in FPINST. (In some cases,
a second opcode might have been accepted by the VFP11 before the
exception was detected and could be reported to the ARM11 - in this
case, the VFP11 also sets FPEXC.FP2V and stores the second opcode in
FPINST2.)
If FPEXC.EX is set, the VFP11 will "bounce" the next FPU opcode issued
by the ARM11 CPU, which will be seen by the ARM11 as an undefined opcode
trap. The VFP support code examines the FPEXC.EX and FPEXC.FP2V bits
to decide what actions to take, i.e., whether to emulate the opcodes
found in FPINST and FPINST2, and whether to retry the bounced instruction.
If a user space application has left the VFP11 in this "pending trap"
state, the next FPU opcode issued to the VFP11 might actually be the
VSTMIA operation vfp_save_state() uses to store the FPU registers
to memory (in our test cases, when building the signal stack frame).
In this case, the kernel crashes as described above.
This patch fixes the problem by making sure that vfp_save_state() is
always entered with FPEXC.EX cleared. (The current value of FPEXC has
already been saved, so this does not corrupt the context. Clearing
FPEXC.EX has no effects on FPINST or FPINST2. Also note that many
callers already modify FPEXC by setting FPEXC.EN before invoking
vfp_save_state().)
This patch also addresses a second problem related to FPEXC.EX: After
returning from signal handling, the kernel reloads the VFP context
from the user mode stack. However, the current code explicitly clears
both FPEXC.EX and FPEXC.FP2V during reload. As VFP11 requires these
bits to be preserved, this patch disables clearing them for VFP
implementations belonging to architecture 1. There should be no
negative side effects: the user can set both bits by executing FPU
opcodes anyway, and while user code may now place arbitrary values
into FPINST and FPINST2 (e.g., non-VFP ARM opcodes) the VFP support
code knows which instructions can be emulated, and rejects other
opcodes with "unhandled bounce" messages, so there should be no
security impact from allowing reloading FPEXC.EX and FPEXC.FP2V.
Signed-off-by: Christopher Alexander Tobias Schulze <cat.schulze@alice-dsl.net>
At present there is no mechanism to specify driver load order,
which can lead to deferrals and repeated retries until successful.
Since this situation is expected, reduce the dmesg level to
INFO and mention that the operation will be retried.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
These divide off of PLLD_PER and are used for the ethernet and wifi
PHYs source PLLs. Neither of them is currently represented by a phy
device that would grab the clock for us.
This keeps other drivers from killing the networking PHYs when they
disable their own clocks and trigger PLLD_PER's refcount going to 0.
v2: Skip marking as critical if they aren't on at boot.
Signed-off-by: Eric Anholt <eric@anholt.net>
The VPU is responsible for managing the core clock, usually under
direction from the bcm2835-cpufreq driver but not via the clk-bcm2835
driver. Since the core frequency can change without warning, it is
safer to report the maximum clock rate to users of the core clock -
I2C, SPI and the mini UART - to err on the safe side when calculating
clock divisors.
If the DT node for the clock driver includes a reference to the
firmware node, use the firmware API to query the maximum core clock
instead of reading the divider registers.
Prior to this patch, a "100KHz" I2C bus was sometimes clocked at about
160KHz. In particular, switching to the 4.9 kernel was likely to break
SenseHAT usage on a Pi3.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The claim-clocks property can be used to prevent PLLs and dividers
from being marked as critical. It contains a vector of clock IDs,
as defined by dt-bindings/clock/bcm2835.h.
Use this mechanism to claim PLLD_DSI0, PLLD_DSI1, PLLH_AUX and
PLLH_PIX for the vc4_kms_v3d driver.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The VPU configures and relies on several PLLs and dividers. Mark all
enabled dividers and their PLLs as CRITICAL to prevent the kernel from
switching them off.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The Raspberry Pi firmware looks at the RSTS register to know which
partition to boot from. The reboot syscall command
LINUX_REBOOT_CMD_RESTART2 supports passing in a string argument.
Add support for passing in a partition number 0..63 to boot from.
Partition 63 is a special partiton indicating halt.
If the partition doesn't exist, the firmware falls back to partition 0.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Load driver early since at least bcm2708_fb doesn't support deferred
probing and even if it did, we don't want the video driver deferred.
Support the legacy DMA API which is needed by bcm2708_fb.
Don't mask out channel 2.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
The spi-bcm2835 driver automatically uses GPIO chip-selects due to
some unreliability of the native ones. In doing so it chooses the
same pins as the native chip-selects would use, but the existing
code always uses pins 7 and 8, wherever the SPI function is mapped.
Search the pinctrl group assigned to the driver for pins that
correspond to native chip-selects, and use those for GPIO chip-
selects.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Add a duplicate irq range with an offset on the hwirq's so the
driver can detect that enable_fiq() is used.
Tested with downstream dwc_otg USB controller driver.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
The old arch-specific IRQ macros included a dsb to ensure the
write to clear the mailbox interrupt completed before returning
from the interrupt. The BCM2836 irqchip driver needs the same
precaution to avoid spurious interrupts.
Spurious interrupts are still possible for other reasons,
though, so trap them early.
smsc95xx is adjusting truesize when it shouldn't, and following a recent patch from Eric this is now triggering warnings.
This patch stops smsc95xx from changing truesize.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
commit a13f085d11 upstream.
This fixes the following issues:
- When a buffer size is supplied to reiserfs_listxattr() such that each
individual name fits, but the concatenation of all names doesn't fit,
reiserfs_listxattr() overflows the supplied buffer. This leads to a
kernel heap overflow (verified using KASAN) followed by an out-of-bounds
usercopy and is therefore a security bug.
- When a buffer size is supplied to reiserfs_listxattr() such that a
name doesn't fit, -ERANGE should be returned. But reiserfs instead just
truncates the list of names; I have verified that if the only xattr on a
file has a longer name than the supplied buffer length, listxattr()
incorrectly returns zero.
With my patch applied, -ERANGE is returned in both cases and the memory
corruption doesn't happen anymore.
Credit for making me clean this code up a bit goes to Al Viro, who pointed
out that the ->actor calling convention is suboptimal and should be
changed.
Link: http://lkml.kernel.org/r/20180802151539.5373-1-jannh@google.com
Fixes: 48b32a3553 ("reiserfs: use generic xattr handlers")
Signed-off-by: Jann Horn <jannh@google.com>
Acked-by: Jeff Mahoney <jeffm@suse.com>
Cc: Eric Biggers <ebiggers@google.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bed4ff1ed4 upstream.
This fixes a race condition, where the DMAEN bit ends up being set after
I2C slave has transmitted a byte following the dummy read. When that
happens, an interrupt is generated instead, and no DMA request is generated
to kickstart the DMA read, and a timeout happens after DMA_TIMEOUT (1 sec).
Fixed by setting the DMAEN bit before the dummy read.
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c463a158cb upstream.
acpi_gsb_i2c_write_bytes() returns i2c_transfer()'s return value, which
is the number of transfers executed on success, so 1.
The ACPI code expects us to store 0 in gsb->status for success, not 1.
Specifically this breaks the following code in the Thinkpad 8 DSDT:
ECWR = I2CW = ECWR /* \_SB_.I2C1.BAT0.ECWR */
If ((ECST == Zero))
{
ECRD = I2CR /* \_SB_.I2C1.I2CR */
}
Before this commit we set ECST to 1, causing the read to never happen
breaking battery monitoring on the Thinkpad 8.
This commit makes acpi_gsb_i2c_write_bytes() return 0 when i2c_transfer()
returns 1, so the single write transfer completed successfully, and
makes it return -EIO on for other (unexpected) return values >= 0.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1204e35bed upstream.
Commit b440bde74f ("PCI: Add pci_ignore_hotplug() to ignore hotplug
events for a device") iterates over the devices on a hotplug port's
subordinate bus in pciehp's IRQ handler without acquiring pci_bus_sem.
It is thus possible for a user to cause a crash by concurrently
manipulating the device list, e.g. by disabling slot power via sysfs
on a different CPU or by initiating a remove/rescan via sysfs.
This can't be fixed by acquiring pci_bus_sem because it may sleep.
The simplest fix is to avoid the list iteration altogether and just
check the ignore_hotplug flag on the port itself. This works because
pci_ignore_hotplug() sets the flag both on the device as well as on its
parent bridge.
We do lose the ability to print the name of the device blocking hotplug
in the debug message, but that's probably bearable.
Fixes: b440bde74f ("PCI: Add pci_ignore_hotplug() to ignore hotplug events for a device")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 281e878eab upstream.
When pciehp is unbound (e.g. on unplug of a Thunderbolt device), the
hotplug_slot struct is deregistered and thus freed before freeing the
IRQ. The IRQ handler and the work items it schedules print the slot
name referenced from the freed structure in various informational and
debug log messages, each time resulting in a quadruple dereference of
freed pointers (hotplug_slot -> pci_slot -> kobject -> name).
At best the slot name is logged as "(null)", at worst kernel memory is
exposed in logs or the driver crashes:
pciehp 0000:10:00.0:pcie204: Slot((null)): Card not present
An attacker may provoke the bug by unplugging multiple devices on a
Thunderbolt daisy chain at once. Unplugging can also be simulated by
powering down slots via sysfs. The bug is particularly easy to trigger
in poll mode.
It has been present since the driver's introduction in 2004:
https://git.kernel.org/tglx/history/c/c16b4b14d980
Fix by rearranging teardown such that the IRQ is freed first. Run the
work items queued by the IRQ handler to completion before freeing the
hotplug_slot struct by draining the work queue from the ->release_slot
callback which is invoked by pci_hp_deregister().
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v2.6.4
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3dbe97efe8 upstream.
PCIe r4.0, sec 9.3.5.4, "Device Control Register", shows both
Max_Payload_Size (MPS) and Max_Read_request_Size (MRRS) to be 'RsvdP' for
VFs. Just prior to the table it states:
"PF and VF functionality is defined in Section 7.5.3.4 except where
noted in Table 9-16. For VF fields marked 'RsvdP', the PF setting
applies to the VF."
All of which implies that with respect to Max_Payload_Size Supported
(MPSS), MPS, and MRRS values, we should not be paying any attention to the
VF's fields, but rather only to the PF's. Only looking at the PF's fields
also logically makes sense as it's the sole physical interface to the PCIe
bus.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200527
Fixes: 27d868b5e6 ("PCI: Set MPS to match upstream bridge")
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # 4.3+
Cc: Keith Busch <keith.busch@intel.com>
Cc: Sinan Kaya <okaya@kernel.org>
Cc: Dongdong Liu <liudongdong3@huawei.com>
Cc: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4ce6435820 upstream.
If addition of sysfs files fails on registration of a hotplug slot, the
struct pci_slot as well as the entry in the slot_list is leaked. The
issue has been present since the hotplug core was introduced in 2002:
https://git.kernel.org/tglx/history/c/a8a2069f432c
Perhaps the idea was that even though sysfs addition fails, the slot
should still be usable. But that's not how drivers use the interface,
they abort probe if a non-zero value is returned.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v2.4.15+
Cc: Greg Kroah-Hartman <greg@kroah.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9d64b539b7 upstream.
Commit 26112ddc25 (PCI / ACPI / PM: Resume bridges w/o drivers on
suspend-to-RAM) attempted to fix a functional regression resulting
from commit c62ec4610c (PM / core: Fix direct_complete handling
for devices with no callbacks) by resuming PCI bridges without
drivers (that is, "parallel PCI" ones) during system-wide suspend if
the target system state is not ACPI S0 (working state).
That turns out insufficient, however, as it is reported that, at
least in one case, the platform firmware gets confused if a PCIe
root port is suspended before entering the ACPI S3 sleep state.
That issue was exposed by commit 77b3729ca03 (PCI / PM: Use
SMART_SUSPEND and LEAVE_SUSPENDED flags for PCIe ports) that allowed
PCIe ports to stay in runtime suspend during system-wide suspend
(which is OK for suspend-to-idle, but turns out to be problematic
otherwise).
For this reason, drop the driver check from acpi_pci_need_resume()
and resume all bridges (including PCIe ports with drivers) during
system-wide suspend if the target system state is not ACPI S0.
[If the target system state is ACPI S0, it means suspend-to-idle
and the platform firmware is not going to be invoked to actually
suspend the system, so there is no need to resume the bridges in
that case.]
Fixes: 77b3729ca03 (PCI / PM: Use SMART_SUSPEND and LEAVE_SUSPENDED flags for PCIe ports)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200675
Reported-by: teika kazura <teika@gmx.com>
Tested-by: teika kazura <teika@gmx.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: 4.16+ <stable@vger.kernel.org> # 4.16+: 26112ddc25 (PCI / ACPI / PM: Resume bridges ...)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit caa21e19e0 upstream.
Invoking shutdown for a socket in state SMC_LISTEN does not make
sense. Nevertheless programs like syzbot fuzzing the kernel may
try to do this. For SMC this means a socket refcounting problem.
This patch makes sure a shutdown call for an SMC socket in state
SMC_LISTEN simply returns with -ENOTCONN.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4576cd469d upstream.
TPACKET_V3 stores variable length frames in fixed length blocks.
Blocks must be able to store a block header, optional private space
and at least one minimum sized frame.
Frames, even for a zero snaplen packet, store metadata headers and
optional reserved space.
In the block size bounds check, ensure that the frame of the
chosen configuration fits. This includes sockaddr_ll and optional
tp_reserve.
Syzbot was able to construct a ring with insuffient room for the
sockaddr_ll in the header of a zero-length frame, triggering an
out-of-bounds write in dev_parse_header.
Convert the comparison to less than, as zero is a valid snap len.
This matches the test for minimum tp_frame_size immediately below.
Fixes: f6fb8f100b ("af-packet: TPACKET_V3 flexible buffer implementation.")
Fixes: eb73190f4f ("net/packet: refine check for priv area size")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6613b6173d upstream.
When first DCCP packet is SYNC or SYNCACK, we insert a new conntrack
that has an un-initialized timeout value, i.e. such entry could be
reaped at any time.
Mark them as INVALID and only ignore SYNC/SYNCACK when connection had
an old state.
Reported-by: syzbot+6f18401420df260e37ed@syzkaller.appspotmail.com
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7797167ffd upstream.
Now that we use a sync prior to releasing the locks in syscall.S, we don't need
the PA 2.0 ordered stores used to release some locks. Using an ordered store,
potentially slows the release and subsequent code.
There are a number of other ordered stores and loads that serve no purpose. I
have converted these to normal stores.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org # 4.0+
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3b885ac1dc upstream.
Now that mb() is an instruction barrier, it will slow performance if we issue
unnecessary barriers.
The spinlock defines have a number of unnecessary barriers. The __ldcw()
define is both a hardware and compiler barrier. The mb() barriers in the
routines using __ldcw() serve no purpose.
The only barrier needed is the one in arch_spin_unlock(). We need to ensure
all accesses are complete prior to releasing the lock.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org # 4.0+
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ddf74e79a5 upstream.
idx can be indirectly controlled by user-space, hence leading to a
potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/gpu/drm/amd/amdgpu/amdgpu_pm.c:408 amdgpu_set_pp_force_state()
warn: potential spectre issue 'data.states'
Fix this by sanitizing idx before using it to index data.states
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit de5372da60 upstream.
info.index can be indirectly controlled by user-space, hence leading
to a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/gpu/drm/i915/gvt/kvmgt.c:1232 intel_vgpu_ioctl() warn:
potential spectre issue 'vgpu->vdev.region' [r]
Fix this by sanitizing info.index before indirectly using it to index
vgpu->vdev.region
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a5d5e5d51 upstream.
'ac->ac_g_ex.fe_len' is a user-controlled value which is used in the
derivation of 'ac->ac_2order'. 'ac->ac_2order', in turn, is used to
index arrays which makes it a potential spectre gadget. Fix this by
sanitizing the value assigned to 'ac->ac2_order'. This covers the
following accesses found with the help of smatch:
* fs/ext4/mballoc.c:1896 ext4_mb_simple_scan_group() warn: potential
spectre issue 'grp->bb_counters' [w] (local cap)
* fs/ext4/mballoc.c:445 mb_find_buddy() warn: potential spectre issue
'EXT4_SB(e4b->bd_sb)->s_mb_offsets' [r] (local cap)
* fs/ext4/mballoc.c:446 mb_find_buddy() warn: potential spectre issue
'EXT4_SB(e4b->bd_sb)->s_mb_maxs' [r] (local cap)
Suggested-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Jeremy Cline <jcline@redhat.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c40a56a781 upstream.
The kernel image is mapped into two places in the virtual address space
(addresses without KASLR, of course):
1. The kernel direct map (0xffff880000000000)
2. The "high kernel map" (0xffffffff81000000)
We actually execute out of #2. If we get the address of a kernel symbol,
it points to #2, but almost all physical-to-virtual translations point to
Parts of the "high kernel map" alias are mapped in the userspace page
tables with the Global bit for performance reasons. The parts that we map
to userspace do not (er, should not) have secrets. When PTI is enabled then
the global bit is usually not set in the high mapping and just used to
compensate for poor performance on systems which lack PCID.
This is fine, except that some areas in the kernel image that are adjacent
to the non-secret-containing areas are unused holes. We free these holes
back into the normal page allocator and reuse them as normal kernel memory.
The memory will, of course, get *used* via the normal map, but the alias
mapping is kept.
This otherwise unused alias mapping of the holes will, by default keep the
Global bit, be mapped out to userspace, and be vulnerable to Meltdown.
Remove the alias mapping of these pages entirely. This is likely to
fracture the 2M page mapping the kernel image near these areas, but this
should affect a minority of the area.
The pageattr code changes *all* aliases mapping the physical pages that it
operates on (by default). We only want to modify a single alias, so we
need to tweak its behavior.
This unmapping behavior is currently dependent on PTI being in place.
Going forward, we should at least consider doing this for all
configurations. Having an extra read-write alias for memory is not exactly
ideal for debugging things like random memory corruption and this does
undercut features like DEBUG_PAGEALLOC or future work like eXclusive Page
Frame Ownership (XPFO).
Before this patch:
current_kernel:---[ High Kernel Mapping ]---
current_kernel-0xffffffff80000000-0xffffffff81000000 16M pmd
current_kernel-0xffffffff81000000-0xffffffff81e00000 14M ro PSE GLB x pmd
current_kernel-0xffffffff81e00000-0xffffffff81e11000 68K ro GLB x pte
current_kernel-0xffffffff81e11000-0xffffffff82000000 1980K RW NX pte
current_kernel-0xffffffff82000000-0xffffffff82600000 6M ro PSE GLB NX pmd
current_kernel-0xffffffff82600000-0xffffffff82c00000 6M RW PSE NX pmd
current_kernel-0xffffffff82c00000-0xffffffff82e00000 2M RW NX pte
current_kernel-0xffffffff82e00000-0xffffffff83200000 4M RW PSE NX pmd
current_kernel-0xffffffff83200000-0xffffffffa0000000 462M pmd
current_user:---[ High Kernel Mapping ]---
current_user-0xffffffff80000000-0xffffffff81000000 16M pmd
current_user-0xffffffff81000000-0xffffffff81e00000 14M ro PSE GLB x pmd
current_user-0xffffffff81e00000-0xffffffff81e11000 68K ro GLB x pte
current_user-0xffffffff81e11000-0xffffffff82000000 1980K RW NX pte
current_user-0xffffffff82000000-0xffffffff82600000 6M ro PSE GLB NX pmd
current_user-0xffffffff82600000-0xffffffffa0000000 474M pmd
After this patch:
current_kernel:---[ High Kernel Mapping ]---
current_kernel-0xffffffff80000000-0xffffffff81000000 16M pmd
current_kernel-0xffffffff81000000-0xffffffff81e00000 14M ro PSE GLB x pmd
current_kernel-0xffffffff81e00000-0xffffffff81e11000 68K ro GLB x pte
current_kernel-0xffffffff81e11000-0xffffffff82000000 1980K pte
current_kernel-0xffffffff82000000-0xffffffff82400000 4M ro PSE GLB NX pmd
current_kernel-0xffffffff82400000-0xffffffff82488000 544K ro NX pte
current_kernel-0xffffffff82488000-0xffffffff82600000 1504K pte
current_kernel-0xffffffff82600000-0xffffffff82c00000 6M RW PSE NX pmd
current_kernel-0xffffffff82c00000-0xffffffff82c0d000 52K RW NX pte
current_kernel-0xffffffff82c0d000-0xffffffff82dc0000 1740K pte
current_user:---[ High Kernel Mapping ]---
current_user-0xffffffff80000000-0xffffffff81000000 16M pmd
current_user-0xffffffff81000000-0xffffffff81e00000 14M ro PSE GLB x pmd
current_user-0xffffffff81e00000-0xffffffff81e11000 68K ro GLB x pte
current_user-0xffffffff81e11000-0xffffffff82000000 1980K pte
current_user-0xffffffff82000000-0xffffffff82400000 4M ro PSE GLB NX pmd
current_user-0xffffffff82400000-0xffffffff82488000 544K ro NX pte
current_user-0xffffffff82488000-0xffffffff82600000 1504K pte
current_user-0xffffffff82600000-0xffffffffa0000000 474M pmd
[ tglx: Do not unmap on 32bit as there is only one mapping ]
Fixes: 0f561fce4d ("x86/pti: Enable global pages for shared areas")
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Kees Cook <keescook@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Joerg Roedel <jroedel@suse.de>
Link: https://lkml.kernel.org/r/20180802225831.5F6A2BFC@viggo.jf.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 490fc05386 ]
Like vm_area_dup(), it initializes the anon_vma_chain head, and the
basic mm pointer.
The rest of the fields end up being different for different users,
although the plan is to also initialize the 'vm_ops' field to a dummy
entry.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 95faf6992d ]
.. and re-initialize th eanon_vma_chain head.
This removes some boiler-plate from the users, and also makes it clear
why it didn't need use the 'zalloc()' version.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3928d4f5ee ]
The vm_area_struct is one of the most fundamental memory management
objects, but the management of it is entirely open-coded evertwhere,
ranging from allocation and freeing (using kmem_cache_[z]alloc and
kmem_cache_free) to initializing all the fields.
We want to unify this in order to end up having some unified
initialization of the vmas, and the first step to this is to at least
have basic allocation functions.
Right now those functions are literally just wrappers around the
kmem_cache_*() calls. This is a purely mechanical conversion:
# new vma:
kmem_cache_zalloc(vm_area_cachep, GFP_KERNEL) -> vm_area_alloc()
# copy old vma
kmem_cache_alloc(vm_area_cachep, GFP_KERNEL) -> vm_area_dup(old)
# free vma
kmem_cache_free(vm_area_cachep, vma) -> vm_area_free(vma)
to the point where the old vma passed in to the vm_area_dup() function
isn't even used yet (because I've left all the old manual initialization
alone).
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9b38276813 ]
The old code in nvme_user_cmd() passed the userspace virtual address
from nvme_passthru_cmd.metadata as the length of the metadata buffer
as well as the address to nvme_submit_user_cmd().
Fixes: 63263d60 ("nvme: Use metadata for passthrough commands")
Signed-off-by: Roland Dreier <roland@purestorage.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2502e5a025 ]
Fix return code check for "max brightness" ACPI call.
The Dell laptop ACPI video brightness control is not present on dell
laptops anymore, but was present in older kernel versions.
The code that checks the return value is incorrect since the SMM
refactoring.
The old code was:
if (buffer->output[0] == 0)
Which was changed to:
ret = dell_send_request(...)
if (ret)
However, dell_send_request() will return 0 if buffer->output[0] == 0,
so we must change the check to:
if (ret == 0)
This issue was found on a Dell M4800 laptop, and the fix tested on it
as well.
Fixes: 549b4930f0 ("dell-smbios: Introduce dispatcher for SMM calls")
Signed-off-by: Damien Thébault <damien@dtbo.net>
Tested-by: Damien Thébault <damien@dtbo.net>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e01a06c808 ]
The Marvell switches report their interrupts in a level sensitive way.
When using edge sensitive detection a race condition in the interrupt
handler of the swich might result in the OS to miss all future events
which might make the switch non-functional.
The problem is that both mv88e6xxx_g2_irq_thread_fn() and
mv88e6xxx_g1_irq_thread_work() sample the irq cause register
(MV88E6XXX_G2_INT_SRC and MV88E6XXX_G1_STS respectively) once and then
handle the observed sources. If after sampling but before all observed
irq sources are handled a new irq source gets active this is not noticed
by the handler which returns unsuspecting, but the interrupt line stays
active which prevents the edge detector to kick in.
All device trees but imx6qdl-zii-rdu2 get this right (most of them by
not specifying an interrupt parent). So fix imx6qdl-zii-rdu2
accordingly.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Fixes: f64992d1a9 ("ARM: dts: imx6: RDU2: Add Switch interrupts")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2c4d6baf1b ]
The ec_no_wakeup matcher added for Thinkpad X1 Carbon 6th gen systems
beyond matched only a single DMI model (20KGS3JF01), that didn't cover
my laptop (20KH002JUS). Change to match based on DMI product family to
cover all X1 6th gen systems.
Signed-off-by: Robin H. Johnson <robbat2@gentoo.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e56b8ce363 ]
Attempt to make cryptic TCP seq number error messages clearer by
(1) identifying the source of the message as "TCP", (2) identifying the
errors as "seq # bug", and (3) grouping the field identifiers and values
by separating them with commas.
E.g., the following message is changed from:
recvmsg bug 2: copied 73BCB6CD seq 70F17CBE rcvnxt 73BCB9AA fl 0
WARNING: CPU: 2 PID: 1501 at /linux/net/ipv4/tcp.c:1881 tcp_recvmsg+0x649/0xb90
to:
TCP recvmsg seq # bug 2: copied 73BCB6CD, seq 70F17CBE, rcvnxt 73BCB9AA, fl 0
WARNING: CPU: 2 PID: 1501 at /linux/net/ipv4/tcp.c:2011 tcp_recvmsg+0x694/0xba0
Suggested-by: 積丹尼 Dan Jacobson <jidanni@jidanni.org>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 711c62dfa6 ]
In case the SPI thread is not running, a simple reset of sync
state won't fix the transmit timeout. We also need to wake up the kernel
thread.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: ed7d42e24e ("net: qca_spi: fix transmit queue timeout handling")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b2bab426dc ]
As long as the synchronization with the QCA7000 isn't finished, we
cannot accept packets from the upper layers. So let the SPI thread
enable the TX queue after sync and avoid unwanted packet drop.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: 291ab06ecf ("net: qualcomm: new Ethernet over SPI driver for QCA7000")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f6bdc42f02 ]
During clc handshake the receive timeout is set to CLC_WAIT_TIME.
Remember and reset the original timeout value after the receive calls,
and remove a duplicate assignment of CLC_WAIT_TIME.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e10f780503 ]
Inside a nested guest, access to hardware can be slow enough that
tsc_read_refs always return ULLONG_MAX, causing tsc_refine_calibration_work
to be called periodically and the nested guest to spend a lot of time
reading the ACPI timer.
However, if the TSC frequency is available from the pvclock page,
we can just set X86_FEATURE_TSC_KNOWN_FREQ and avoid the recalibration.
'refine' operation.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Peng Hao <peng.hao2@zte.com.cn>
[Commit message rewritten. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3a9b045506 ]
This driver can spam the kernel log with multiple messages of:
net eth0: eth0: allmulti set
Usually 4 or 8 at a time (probably because of using ConnMan).
This message doesn't seem useful, so let's demote it from dev_info()
to dev_dbg().
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4aac0b4347 ]
octeon_mgmt driver doesn't drop RX frames that are 1-4 bytes bigger than
MTU set for the corresponding interface. The problem is in the
AGL_GMX_RX0/1_FRM_MAX register setting, which should not account for VLAN
tagging.
According to Octeon HW manual:
"For tagged frames, MAX increases by four bytes for each VLAN found up to a
maximum of two VLANs, or MAX + 8 bytes."
OCTEON_FRAME_HEADER_LEN "define" is fine for ring buffer management, but
should not be used for AGL_GMX_RX0/1_FRM_MAX.
The problem could be easily reproduced using "ping" command. If affected
system has default MTU 1500, other host (having MTU >= 1504) can
successfully "ping" the affected system with payload size 1473-1476,
resulting in IP packets of size 1501-1504 accepted by the mgmt driver.
Fixed system still accepts IP packets of 1500 bytes even with VLAN tagging,
because the limits are lifted in HW as expected, for every VLAN tag.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 665d4953cd ]
In commit ac0b4145d6 ("btrfs: scrub: Don't use inode pages for device
replace") we removed the branch of copy_nocow_pages() to avoid
corruption for compressed nodatasum extents.
However above commit only solves the problem in scrub_extent(), if
during scrub_pages() we failed to read some pages,
sctx->no_io_error_seen will be non-zero and we go to fixup function
scrub_handle_errored_block().
In scrub_handle_errored_block(), for sctx without csum (no matter if
we're doing replace or scrub) we go to scrub_fixup_nodatasum() routine,
which does the similar thing with copy_nocow_pages(), but does it
without the extra check in copy_nocow_pages() routine.
So for test cases like btrfs/100, where we emulate read errors during
replace/scrub, we could corrupt compressed extent data again.
This patch will fix it just by avoiding any "optimization" for
nodatasum, just falls back to the normal fixup routine by try read from
any good copy.
This also solves WARN_ON() or dead lock caused by lame backref iteration
in scrub_fixup_nodatasum() routine.
The deadlock or WARN_ON() won't be triggered before commit ac0b4145d6
("btrfs: scrub: Don't use inode pages for device replace") since
copy_nocow_pages() have better locking and extra check for data extent,
and it's already doing the fixup work by try to read data from any good
copy, so it won't go scrub_fixup_nodatasum() anyway.
This patch disables the faulty code and will be removed completely in a
followup patch.
Fixes: ac0b4145d6 ("btrfs: scrub: Don't use inode pages for device replace")
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d3f6daede2 ]
pwm node should not be under gpio6 node in the device tree.
This fixes detection of the pwm on Droid 4.
Fixes: 6d7bdd328d ("ARM: dts: omap4-droid4: update touchscreen")
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
[tony@atomide.com: added fixes tag]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3578a7ecb6 ]
Testing has uncovered a failure case that is not handled properly. In the
event that a login fails and we are not able to recover on the spot, we
return 0 from do_reset, preventing any error recovery code from being
triggered. Additionally, the state is set to "probed" meaning that when we
are able to trigger the error recovery, the driver always comes up in the
probed state. To handle the case properly, we need to return a failure code
here and set the adapter state to the state that we entered the reset in
indicating the state that we would like to come out of the recovery reset
in.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c133459765 ]
CC [M] drivers/net/ethernet/freescale/fman/fman.o
In file included from ../drivers/net/ethernet/freescale/fman/fman.c:35:
../include/linux/fsl/guts.h: In function 'guts_set_dmacr':
../include/linux/fsl/guts.h:165:2: error: implicit declaration of function 'clrsetbits_be32' [-Werror=implicit-function-declaration]
clrsetbits_be32(&guts->dmacr, 3 << shift, device << shift);
^~~~~~~~~~~~~~~
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Madalin Bucur <madalin.bucur@nxp.com>
Cc: netdev@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 916c5e1413 ]
The netvsc device may need to fallback to running in single queue
mode if host side only wants to support single queue.
Recent change for handling mtu broke this in setup logic.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 3ffe64f1a6 ("hv_netvsc: split sub-channel setup into async and sync")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2d14d37952 ]
During a device failover, there may be latency between the loss
of the current backing device and a notification from firmware that
a failover has occurred. This latency can result in a large amount of
error printouts as firmware returns outgoing traffic with a generic
error code. These are not necessarily errors in this case as the
firmware is busy swapping in a new backing adapter and is not ready
to send packets yet. This patch reclassifies those error codes as
warnings with an explanation that a failover may be pending. All
other return codes will be considered errors.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b9952b5218 ]
A comment in the review of the patch adding the phandle cache said that
the cache would have to be updated when modules are applied and removed.
This patch implements the cache updates.
Fixes: 0b3ce78e90 ("of: cache phandle nodes to reduce cost of of_find_node_by_phandle()")
Reported-by: Alan Tull <atull@kernel.org>
Suggested-by: Alan Tull <atull@kernel.org>
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e117cb52bd ]
Mark noticed that syzkaller is able to reliably trigger the following warning:
dl_rq->running_bw > dl_rq->this_bw
WARNING: CPU: 1 PID: 153 at kernel/sched/deadline.c:124 switched_from_dl+0x454/0x608
Kernel panic - not syncing: panic_on_warn set ...
CPU: 1 PID: 153 Comm: syz-executor253 Not tainted 4.18.0-rc3+ #29
Hardware name: linux,dummy-virt (DT)
Call trace:
dump_backtrace+0x0/0x458
show_stack+0x20/0x30
dump_stack+0x180/0x250
panic+0x2dc/0x4ec
__warn_printk+0x0/0x150
report_bug+0x228/0x2d8
bug_handler+0xa0/0x1a0
brk_handler+0x2f0/0x568
do_debug_exception+0x1bc/0x5d0
el1_dbg+0x18/0x78
switched_from_dl+0x454/0x608
__sched_setscheduler+0x8cc/0x2018
sys_sched_setattr+0x340/0x758
el0_svc_naked+0x30/0x34
syzkaller reproducer runs a bunch of threads that constantly switch
between DEADLINE and NORMAL classes while interacting through futexes.
The splat above is caused by the fact that if a DEADLINE task is setattr
back to NORMAL while in non_contending state (blocked on a futex -
inactive timer armed), its contribution to running_bw is not removed
before sub_rq_bw() gets called (!task_on_rq_queued() branch) and the
latter sees running_bw > this_bw.
Fix it by removing a task contribution from running_bw if the task is
not queued and in non_contending state while switched to a different
class.
Reported-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Juri Lelli <juri.lelli@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Daniel Bristot de Oliveira <bristot@redhat.com>
Reviewed-by: Luca Abeni <luca.abeni@santannapisa.it>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: claudio@evidence.eu.com
Cc: rostedt@goodmis.org
Link: http://lkml.kernel.org/r/20180711072948.27061-1-juri.lelli@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c29e9da56b ]
platform_get_resource() may fail and return NULL, so we should
better check it's return value to avoid a NULL pointer dereference
a bit later in the code.
This is detected by Coccinelle semantic patch.
@@
expression pdev, res, n, t, e, e1, e2;
@@
res = platform_get_resource(pdev, t, n);
+ if (!res)
+ return -EINVAL;
... when != res == NULL
e = devm_ioremap_nocache(e1, res->start, e2);
Fixes: cc4fa83f66 ("pinctrl: nsp: add pinmux driver support for Broadcom NSP SoC")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 993675a310 ]
If variable length link layer headers result in a packet shorter
than dev->hard_header_len, reset the network header offset. Else
skb->mac_len may exceed skb->len after skb_mac_reset_len.
packet_sendmsg_spkt already has similar logic.
Fixes: b84bbaf7a6 ("packet: in packet_snd start writing at link layer allocation")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 193f20033c ]
We should take and release the filter_sem consistently during the
reset process, in the same manner as the mac_lock and reset_lock.
For lockdep consistency we also take the filter_sem for write around
other calls to efx->type->init().
Fixes: c2bebe37c6 ("sfc: give ef10 its own rwsem in the filter table instead of filter_lock")
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1c56c0994a ]
In some situations we may end up calling down_read while already
holding the semaphore for write, thus hanging. This has been seen
when setting the MAC address for the interface. The hung task log
in this situation includes this stack:
down_read
efx_ef10_filter_insert
efx_ef10_filter_insert_addr_list
efx_ef10_filter_vlan_sync_rx_mode
efx_ef10_filter_add_vlan
efx_ef10_filter_table_probe
efx_ef10_set_mac_address
efx_set_mac_address
dev_set_mac_address
In addition, lockdep rightly points out that nested calling of
down_read is incorrect.
Fixes: c2bebe37c6 ("sfc: give ef10 its own rwsem in the filter table instead of filter_lock")
Tested-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8d4235f715 ]
[Why]
When a dce100 asic was suspended, the clocks were not set to 0.
Upon resume, the new clock was compared to the existing clock,
they were found to be the same, and so the clock was not set.
This resulted in a pernicious blackscreen.
[How]
In atomic commit, check to see if there are any active pipes.
If no, set clocks to 0
Signed-off-by: David Francis <David.Francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d14c780c11 ]
This change makes it so that we are much more explicit about the ordering
of updates to the receive address register (RAR) table. Prior to this patch
I believe we may have been updating the table while entries were still
active, or possibly allowing for reordering of things since we weren't
explicitly flushing writes to either the lower or upper portion of the
register prior to accessing the other half.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Reviewed-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 923847413f ]
The AM3517 has a different OTG controller location than the OMAP3,
which is included from omap3.dtsi. This results in a hwmod error.
Since the AM3517 has a different OTG controller address, this patch
disabes one that is isn't available.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2f8b5b2183 ]
Call secure services to enable ACTLR[0] (Enable invalidates of BTB with
ICIALLU) when branch hardening is enabled for kernel.
On GP devices OMAP5/DRA7, there is no possibility to update secure
side since "secure world" is ROM and there are no override mechanisms
possible. On HS devices, appropriate PPA should do the workarounds as
well.
However, the configuration is only done for secondary core, since it is
expected that firmware/bootloader will have enabled the required
configuration for the primary boot core (note: bootloaders typically
will NOT enable secondary processors, since it has no need to do so).
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 576cd32082 ]
It was been observed that with a particular order of initialisation,
the netdev can be up, but the SFP module still has its TX_DISABLE
signal asserted. This occurs when the network device brought up before
the SFP kernel module has been inserted by userspace.
This occurs because sfp-bus layer does not hear about the change in
network device state, and so assumes that it is still down. Set
netdev->sfp when the upstream is registered to work around this problem.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b4c7e2bd2e ]
Dynamic ftrace requires modifying the code segments that are usually
set to read-only. To do this, a per arch function is called both before
and after the ftrace modifications are performed. The "before" function
will set kernel code text to read-write to allow for ftrace to make the
modifications, and the "after" function will set the kernel code text
back to "read-only" to keep the kernel code text protected.
The issue happens when dynamic ftrace is tested at boot up. The test is
done before the kernel code text has been set to read-only. But the
"before" and "after" calls are still performed. The "after" call will
change the kernel code text to read-only prematurely, and other boot
code that expects this code to be read-write will fail.
The solution is to add a variable that is set when the kernel code text
is expected to be converted to read-only, and make the ftrace "before"
and "after" calls do nothing if that variable is not yet set. This is
similar to the x86 solution from commit 1623963097 ("ftrace, x86:
make kernel text writable only for conversions").
Link: http://lkml.kernel.org/r/20180620212906.24b7b66e@vmware.local.home
Reported-by: Stefan Agner <stefan@agner.ch>
Tested-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ee6581ceba ]
Incremental patch to fix the unchecked dereference in acpi_nfit_ctl.
Reported by Dan Carpenter:
"acpi/nfit: fix cmd_rc for acpi_nfit_ctl to
always return a value" from Jun 28, 2018, leads to the following
Smatch complaint:
drivers/acpi/nfit/core.c:578 acpi_nfit_ctl()
warn: variable dereferenced before check 'cmd_rc' (see line 411)
drivers/acpi/nfit/core.c
410
411 *cmd_rc = -EINVAL;
^^^^^^^^^^^^^^^^^^
Patch adds unchecked dereference.
Fixes: c1985cefd8 ("acpi/nfit: fix cmd_rc for acpi_nfit_ctl to always return a value")
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 32aa928a7b ]
Builds started failing in Fedora on Python 3.7 with:
`.gnu.debuglto_.debug_macro' referenced in section
`.gnu.debuglto_.debug_macro' of
util/scripting-engines/trace-event-python.o: defined in discarded
section
In Fedora, Python 3.7 added -flto to the list of --cflags and since it
was only applied to util/scripting-engines/trace-event-python.c and
scripts/python/Perf-Trace-Util/Context.c, linking failed.
It's not the first time the addition of flags has broken builds: commit
c6707fdef7 ("perf tools: Fix up build in hardnened environments")
appears to have fixed a similar problem. "python-config --includes"
provides the proper -I flags and doesn't introduce additional CFLAGS.
Signed-off-by: Jeremy Cline <jcline@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20180710154612.6285-1-jcline@redhat.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit db0ba84c04 ]
The dictionaries are attached to the parameter tuple that steals the
references and takes care of releasing them when appropriate. The code
should not decrement the reference counts explicitly. E.g. if libpython
has been built with reference debugging enabled, the superfluous DECREFs
will trigger this error when running perf script:
Fatal Python error: Objects/tupleobject.c:238 object at
0x7f10f2041b40 has negative ref count -1
Aborted (core dumped)
If the reference debugging is not enabled, the superfluous DECREFs might
cause the dict objects to be silently released while they are still in
use. This may trigger various other assertions or just cause perf
crashes and/or weird and unexpected data changes in the stored Python
objects.
Signed-off-by: Janne Huttunen <janne.huttunen@nokia.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jaroslav Skarvada <jskarvad@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1531133990-17485-1-git-send-email-janne.huttunen@nokia.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a09603f851 ]
We are getting following warnings on gcc8 that break compilation:
$ make
CC jvmti/jvmti_agent.o
jvmti/jvmti_agent.c: In function ‘jvmti_open’:
jvmti/jvmti_agent.c:252:35: error: ‘/jit-’ directive output may be truncated \
writing 5 bytes into a region of size between 1 and 4096 [-Werror=format-truncation=]
snprintf(dump_path, PATH_MAX, "%s/jit-%i.dump", jit_path, getpid());
There's no point in checking the result of snprintf call in
jvmti_open, the following open call will fail in case the
name is mangled or too long.
Using tools/lib/ function scnprintf that touches the return value from
the snprintf() calls and thus get rid of those warnings.
$ make DEBUG=1
CC arch/x86/util/perf_regs.o
arch/x86/util/perf_regs.c: In function ‘arch_sdt_arg_parse_op’:
arch/x86/util/perf_regs.c:229:4: error: ‘strncpy’ output truncated before terminating nul
copying 2 bytes from a string of the same length [-Werror=stringop-truncation]
strncpy(prefix, "+0", 2);
^~~~~~~~~~~~~~~~~~~~~~~~
Using scnprintf instead of the strncpy (which we know is safe in here)
to get rid of that warning.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20180702134202.17745-1-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b9626f45ab ]
The below path error can occur:
# ./xdp2skb_meta.sh --dev eth0 --list
./xdp2skb_meta.sh: line 61: /usr/sbin/tc: No such file or directory
So just use command names instead of absolute paths of tc and ip.
In addition, it allow callers to redefine $TC and $IP paths
Fixes: 36e04a2d78 ("samples/bpf: xdp2skb_meta shows transferring info from XDP to SKB")
Reviewed-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Taeung Song <treeze.taeung@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 30f529473e ]
Calling bnxt_set_max_func_irqs() to modify the max IRQ count requested or
freed by the RDMA driver is flawed. The max IRQ count is checked when
re-initializing the IRQ vectors and this can happen multiple times
during ifup or ethtool -L. If the max IRQ is reduced and the RDMA
driver is operational, we may not initailize IRQs correctly. This
problem shows up on VFs with very small number of MSIX.
There is no other logic that relies on the IRQ count excluding the ones
used by RDMA. So we fix it by just removing the call to subtract or
add the IRQs used by RDMA.
Fixes: a588e4580a ("bnxt_en: Add interface to support RDMA driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 78f058a4aa ]
The current code returns -ENOMEM and does not bother to set the output
parameters to 0 when no rings are available. Some callers, such as
bnxt_get_channels() will display garbage ring numbers when that happens.
Fix it by always setting the output parameters.
Fixes: 6e6c5a57fb ("bnxt_en: Modify bnxt_get_max_rings() to support shared or non shared rings.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 07f4fde53d ]
If there aren't enough RX rings available, the driver will attempt to
use a single RX ring without the aggregation ring. If that also
fails, the BNXT_FLAG_AGG_RINGS flag is cleared but the other ring
parameters are not set consistently to reflect that. If more RX
rings become available at the next open, the RX rings will be in
an inconsistent state and may crash when freeing the RX rings.
Fix it by restoring the BNXT_FLAG_AGG_RINGS if not enough RX rings are
available to run without aggregation rings.
Fixes: bdbd1eb59c ("bnxt_en: Handle no aggregation ring gracefully.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e32d4e60b3 ]
It is possible that OVS may set don’t care for DEI/CFI bit in
vlan_tci mask. Hence, checking for vlan_tci exact match will endup
in a vlan flow rejection.
This patch fixes the problem by checking for vlan_pcp and vid
separately, instead of checking for the entire vlan_tci.
Fixes: e85a9be93c (bnxt_en: do not allow wildcard matches for L2 flows)
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e8708786d4 ]
This is used in configs lacking hardware atomics to emulate atomic r-m-w
for user space, implemented by disabling preemption in kernel.
However there are issues in current implementation:
1. Process not terminated if invalid user pointer passed:
i.e. __get_user() failed.
2. The reason for this patch was __put_user() failure not being handled
either, specifically for the COW break scenario.
The zero page is initially wired up and read from __get_user()
succeeds. A subsequent write by __put_user() induces a
Protection Violation, but COW can't finish as Linux page fault
handler is disabled due to preempt disable.
And what's worse is we silently return the stale value to user space.
Fix this specific case by re-enabling preemption and explicitly
fixing up the fault and retrying the whole sequence over.
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: linux-arch@vger.kernel.org
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
[vgupta: rewrote the changelog]
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ec58ba16e1 ]
In case of HSDK we have intermediate INTC in for of DW APB GPIO controller
which is used as a de-bounce logic for interrupt wires that come from
outside the board.
We cannot use existing "irq-dw-apb-ictl" driver here because all input
lines are routed to corresponding output lines but not muxed into one
line (this is configured in RTL and we cannot change this in software).
But even if we add such a feature to "irq-dw-apb-ictl" driver that won't
benefit us as higher-level INTC (in case of HSDK it is IDU) anyways has
per-input control so adding fully-controller intermediate INTC will only
bring some overhead on interrupt processing but no other benefits.
Thus we just do one-time configuration of DW APB GPIO controller and
forget about it.
Based on implementation available on arch/arc/plat-axs10x/axs10x.c file.
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2045cdfa1b ]
Loading the nf_conntrack module with doubled hashsize parameter, i.e.
modprobe nf_conntrack hashsize=12345 hashsize=12345
causes NULL-ptr deref.
If 'hashsize' specified twice, the nf_conntrack_set_hashsize() function
will be called also twice.
The first nf_conntrack_set_hashsize() call will set the
'nf_conntrack_htable_size' variable:
nf_conntrack_set_hashsize()
...
/* On boot, we can set this without any fancy locking. */
if (!nf_conntrack_htable_size)
return param_set_uint(val, kp);
But on the second invocation, the nf_conntrack_htable_size is already set,
so the nf_conntrack_set_hashsize() will take a different path and call
the nf_conntrack_hash_resize() function. Which will crash on the attempt
to dereference 'nf_conntrack_hash' pointer:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
RIP: 0010:nf_conntrack_hash_resize+0x255/0x490 [nf_conntrack]
Call Trace:
nf_conntrack_set_hashsize+0xcd/0x100 [nf_conntrack]
parse_args+0x1f9/0x5a0
load_module+0x1281/0x1a50
__se_sys_finit_module+0xbe/0xf0
do_syscall_64+0x7c/0x390
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Fix this, by checking !nf_conntrack_hash instead of
!nf_conntrack_htable_size. nf_conntrack_hash will be initialized only
after the module loaded, so the second invocation of the
nf_conntrack_set_hashsize() won't crash, it will just reinitialize
nf_conntrack_htable_size again.
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 21d5e07819 ]
iptables-nft never requests these, but make this explicitly illegal.
If it were quested, kernel could oops as ->eval is NULL, furthermore,
the builtin targets have no owning module so its possible to rmmod
eb/ip/ip6_tables module even if they would be loaded.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 92298c1cd8 ]
Add the missing locks to the IRQ enable/disable paths, and fix a comment
in the interrupt handler: reading the ISR clears down the status bits,
but does not reset the interrupt so it can signal again. That seems to
require a write.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5265f0338b ]
Here we are checking for the buffer length, not an offset for writing
to, so using > is correct. The current code incorrectly rejects a
command buffer ending at the memory buffer's end.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4466b1f0e0 ]
Host1x's CDMA can't access the command buffers if IOMMU and Host1x
firewall are enabled in the kernels config because firewall doesn't map
the copied buffer into IOVA space. Fix this by skipping IOMMU
initialization if firewall is enabled as firewall merges sparse cmdbufs
into a single contiguous buffer and hence IOMMU isn't needed in this case.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8a81388ec2 ]
Instead of having the function name hard-coded (it might change and we
forgot to update them in the debug output) we can use __func__ instead
and also shorter the line so we do not need to break it. Also fix an
extra blank line while being here.
Found by checkpatch.
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f6f2a4a2eb ]
Setting the low threshold to 0 has no effect on frags allocation,
we need to clear high_thresh instead.
The code was pre-existent to commit 648700f76b ("inet: frags:
use rhashtables for reassembly units"), but before the above,
such assignment had a different role: prevent concurrent eviction
from the worker and the netns cleanup helper.
Fixes: 648700f76b ("inet: frags: use rhashtables for reassembly units")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0c6bc6e531 ]
Multiple BPF helpers in use by sk_skb programs calculate the max
skb length using the __bpf_skb_max_len function. However, this
calculates the max length using the skb->dev pointer which can be
NULL when an sk_skb program is paired with an sk_msg program.
To force this a sk_msg program needs to redirect into the ingress
path of a sock with an attach sk_skb program. Then the the sk_skb
program would need to call one of the helpers that adjust the skb
size.
To fix the null ptr dereference use SKB_MAX_ALLOC size if no dev
is available.
Fixes: 8934ce2fd0 ("bpf: sockmap redirect ingress support")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 87ed1405ef ]
In commit ca04d9d3e1 ("phy: qcom-qusb2: New driver for QUSB2 PHY on
Qcom chips") you can see a call like:
devm_nvmem_cell_get(dev, NULL);
Note that the cell ID passed to the function is NULL. This is because
the qcom-qusb2 driver is expected to work only on systems where the
PHY node is hooked up via device-tree and is nameless.
This works OK for the most part. The first thing nvmem_cell_get()
does is to call of_nvmem_cell_get() and there it's documented that a
NULL name is fine. The problem happens when the call to
of_nvmem_cell_get() returns -EINVAL. In such a case we'll fall back
to nvmem_cell_get_from_list() and eventually might (if nvmem_cells
isn't an empty list) crash with something that looks like:
strcmp
nvmem_find_cell
__nvmem_device_get
nvmem_cell_get_from_list
nvmem_cell_get
devm_nvmem_cell_get
qusb2_phy_probe
There are several different ways we could fix this problem:
One could argue that perhaps the qcom-qusb2 driver should be changed
to use of_nvmem_cell_get() which is allowed to have a NULL name. In
that case, we'd need to add a patche to introduce
devm_of_nvmem_cell_get() since the qcom-qusb2 driver is using devm
managed resources.
One could also argue that perhaps we could just add a name to
qcom-qusb2. That would be OK but I believe it effectively changes the
device tree bindings, so maybe it's a no-go.
In this patch I have chosen to fix the problem by simply not crashing
when a NULL cell_id is passed to nvmem_cell_get().
NOTE: that for the qcom-qusb2 driver the "nvmem-cells" property is
defined to be optional and thus it's expected to be a common case that
we would hit this crash and this is more than just a theoretical fix.
Fixes: ca04d9d3e1 ("phy: qcom-qusb2: New driver for QUSB2 PHY on Qcom chips")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0c1049dcb4 ]
PXA3xx platforms have 56 interrupts that are stored in two ICMR
registers. The code in pxa_irq_suspend() and pxa_irq_resume() however
does a simple division by 32 which only leads to one register being
saved at suspend and restored at resume time. The NAND interrupt
setting, for instance, is lost.
Fix this by using DIV_ROUND_UP() instead.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 843789f6dd ]
t4_get_flash_params() fails in a fatal fashion if the FLASH part isn't
one of the recognized parts. But this leads to desperate efforts to update
drivers when various FLASH parts which we are using suddenly become
unavailable and we need to substitute new FLASH parts. This has lead to
more than one Customer Field Emergency when a Customer has an old driver
and suddenly can't use newly shipped adapters.
This commit fixes this by simply assuming that the FLASH part is 4MB in
size if it can't be identified. Note that all Chelsio adapters will have
flash parts which are at least 4MB in size.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9faa89d4ed ]
The setting of the node address is not thread safe, meaning that
two discoverers may decide to set it simultanously, with a duplicate
entry in the name table as result. We fix that with this commit.
Fixes: 25b0b9c4e8 ("tipc: handle collisions of 32-bit node address hash values")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 92018c7ca9 ]
The duplicate address discovery protocol is not safe against two
discoverers running in parallel. The one executing first after the
trial period is over will set the node address and change its own
message type to DSC_REQ_MSG. The one executing last may find that the
node address is already set, and never change message type, with the
result that its links may never be established.
In this commmit we ensure that the message type always is set correctly
after the trial period is over.
Fixes: 25b0b9c4e8 ("tipc: handle collisions of 32-bit node address hash values")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e415577f57 ]
With the duplicate address discovery protocol for tipc nodes addresses
we introduced a one second trial period before a node is allocated a
hash number to use as address.
Unfortunately, we miss to handle the case when a regular LINK REQUEST/
RESPONSE arrives from a cluster node during the trial period. Such
messages are not ignored as they should be, leading to links setup
attempts while the node still has no address.
Fixes: 25b0b9c4e8 ("tipc: handle collisions of 32-bit node address hash values")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2a57f18242 ]
The function for checking if there is an node address conflict is
supposed to return a suggestion for a new address if it finds a
conflict, and zero otherwise. But in case the peer being checked
is previously unknown it does instead return a "suggestion" for
the checked address itself. This results in a DSC_TRIAL_FAIL_MSG
being sent unecessarily to the peer, and sometimes makes the trial
period starting over again.
Fixes: 25b0b9c4e8 ("tipc: handle collisions of 32-bit node address hash values")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 05925e52a7 ]
The change fixes sleep in atomic context bug, which is encountered
every time when link settings are changed by ethtool.
Since commit 35b5f6b1a8 ("PHYLIB: Locking fixes for PHY I/O
potentially sleeping") phy_start_aneg() function utilizes a mutex
to serialize changes to phy state, however that helper function is
called in atomic context under a grabbed spinlock, because
phy_start_aneg() is called by phy_ethtool_ksettings_set() and by
replaced phy_ethtool_sset() helpers from phylib.
Now duplex mode setting is enforced in ravb_adjust_link() only, also
now RX/TX is disabled when link is put down or modifications to E-MAC
registers ECMR and GECMR are expected for both cases of checked and
ignored link status pin state from E-MAC interrupt handler.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0973a4dd79 ]
Since commit 35b5f6b1a8 ("PHYLIB: Locking fixes for PHY I/O
potentially sleeping") phy_start_aneg() function utilizes a mutex
to serialize changes to phy state, however the helper function is
called in atomic context.
The bug can be reproduced by running "ethtool -r" command, the bug
is reported if CONFIG_DEBUG_ATOMIC_SLEEP build option is enabled.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5cb3f52a11 ]
The change fixes sleep in atomic context bug, which is encountered
every time when link settings are changed by ethtool.
Since commit 35b5f6b1a8 ("PHYLIB: Locking fixes for PHY I/O
potentially sleeping") phy_start_aneg() function utilizes a mutex
to serialize changes to phy state, however that helper function is
called in atomic context under a grabbed spinlock, because
phy_start_aneg() is called by phy_ethtool_ksettings_set() and by
replaced phy_ethtool_sset() helpers from phylib.
Now duplex mode setting is enforced in sh_eth_adjust_link() only,
also now RX/TX is disabled when link is put down or modifications
to E-MAC registers ECMR and GECMR are expected for both cases of
checked and ignored link status pin state from E-MAC interrupt handler.
For reference the change is a partial rework of commit 1e1b812bbe
("sh_eth: fix handling of no LINK signal").
Fixes: dc19e4e5e0 ("sh: sh_eth: Add support ethtool")
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 53a710b504 ]
Since commit 35b5f6b1a8 ("PHYLIB: Locking fixes for PHY I/O
potentially sleeping") phy_start_aneg() function utilizes a mutex
to serialize changes to phy state, however the helper function is
called in atomic context.
The bug can be reproduced by running "ethtool -r" command, the bug
is reported if CONFIG_DEBUG_ATOMIC_SLEEP build option is enabled.
Fixes: dc19e4e5e0 ("sh: sh_eth: Add support ethtool")
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d27e77a3de ]
All the control messages broadcast to remote routers are using
QRTR_NODE_BCAST instead of using local router NODE ID which cause
the packets to be dropped on remote router due to invalid NODE ID.
Signed-off-by: Arun Kumar Neelakantam <aneela@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a9ba23d48d ]
At present the ipv6_renew_options_kern() function ends up calling into
access_ok() which is problematic if done from inside an interrupt as
access_ok() calls WARN_ON_IN_IRQ() on some (all?) architectures
(x86-64 is affected). Example warning/backtrace is shown below:
WARNING: CPU: 1 PID: 3144 at lib/usercopy.c:11 _copy_from_user+0x85/0x90
...
Call Trace:
<IRQ>
ipv6_renew_option+0xb2/0xf0
ipv6_renew_options+0x26a/0x340
ipv6_renew_options_kern+0x2c/0x40
calipso_req_setattr+0x72/0xe0
netlbl_req_setattr+0x126/0x1b0
selinux_netlbl_inet_conn_request+0x80/0x100
selinux_inet_conn_request+0x6d/0xb0
security_inet_conn_request+0x32/0x50
tcp_conn_request+0x35f/0xe00
? __lock_acquire+0x250/0x16c0
? selinux_socket_sock_rcv_skb+0x1ae/0x210
? tcp_rcv_state_process+0x289/0x106b
tcp_rcv_state_process+0x289/0x106b
? tcp_v6_do_rcv+0x1a7/0x3c0
tcp_v6_do_rcv+0x1a7/0x3c0
tcp_v6_rcv+0xc82/0xcf0
ip6_input_finish+0x10d/0x690
ip6_input+0x45/0x1e0
? ip6_rcv_finish+0x1d0/0x1d0
ipv6_rcv+0x32b/0x880
? ip6_make_skb+0x1e0/0x1e0
__netif_receive_skb_core+0x6f2/0xdf0
? process_backlog+0x85/0x250
? process_backlog+0x85/0x250
? process_backlog+0xec/0x250
process_backlog+0xec/0x250
net_rx_action+0x153/0x480
__do_softirq+0xd9/0x4f7
do_softirq_own_stack+0x2a/0x40
</IRQ>
...
While not present in the backtrace, ipv6_renew_option() ends up calling
access_ok() via the following chain:
access_ok()
_copy_from_user()
copy_from_user()
ipv6_renew_option()
The fix presented in this patch is to perform the userspace copy
earlier in the call chain such that it is only called when the option
data is actually coming from userspace; that place is
do_ipv6_setsockopt(). Not only does this solve the problem seen in
the backtrace above, it also allows us to simplify the code quite a
bit by removing ipv6_renew_options_kern() completely. We also take
this opportunity to cleanup ipv6_renew_options()/ipv6_renew_option()
a small amount as well.
This patch is heavily based on a rough patch by Al Viro. I've taken
his original patch, converted a kmemdup() call in do_ipv6_setsockopt()
to a memdup_user() call, made better use of the e_inval jump target in
the same function, and cleaned up the use ipv6_renew_option() by
ipv6_renew_options().
CC: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d376bef9c2 ]
nft_compat relies on xt_request_find_match to increment
refcount of the module that provides the match/target.
The (builtin) icmp matches did't set the module owner so it
was possible to rmmod ip(6)tables while icmp extensions were still in use.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a6032120d3 ]
Without CONFIG_GPIOLIB, some headers are not included implicitly,
leading to a build failure:
drivers/net/ieee802154/mcr20a.c: In function 'mcr20a_probe':
drivers/net/ieee802154/mcr20a.c:1347:13: error: implicit declaration of function 'irq_get_trigger_type'; did you mean 'irq_get_irqchip_state'? [-Werror=implicit-function-declaration]
This includes gpio/consumer.h and irq.h directly rather through the
gpiolib header.
Fixes: 8c6ad9cc51 ("ieee802154: Add NXP MCR20A IEEE 802.15.4 transceiver driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Xue Liu <liuxuenetmail@gmail.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 492b7e8945 ]
To avoid the below build warning message,
use new generate_load() checking the return value.
ignoring return value of ‘system’, declared with attribute warn_unused_result
And it also refactors the duplicate code of both
test_perf_event_all_cpu() and test_perf_event_task()
Cc: Teng Qin <qinteng@fb.com>
Signed-off-by: Taeung Song <treeze.taeung@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4d5d33a085 ]
This fixes build error regarding redefinition:
CLANG-bpf samples/bpf/parse_varlen.o
samples/bpf/parse_varlen.c:111:8: error: redefinition of 'vlan_hdr'
struct vlan_hdr {
^
./include/linux/if_vlan.h:38:8: note: previous definition is here
So remove duplicate 'struct vlan_hdr' in sample code and include if_vlan.h
Signed-off-by: Taeung Song <treeze.taeung@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8606544890 ]
This file has never existed in the upstream kernel, but it's guarded by
an #ifdef that's also never existed in the upstream kernel. As a part
of our interrupt controller refactoring this header is no longer
necessary, but this reference managed to sneak in anyway.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d461e3da90 ]
In certain conditions, the device may not be able to link in gigabit mode. This software workaround ensures that the device will not enter the failure state.
Fixes: d0cad87170 ("SMSC75XX USB 2.0 Gigabit Ethernet Devices")
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1e8e18f694 ]
There is a special case that the size is "(N << KASAN_SHADOW_SCALE_SHIFT)
Pages plus X", the value of X is [1, KASAN_SHADOW_SCALE_SIZE-1]. The
operation "size >> KASAN_SHADOW_SCALE_SHIFT" will drop X, and the
roundup operation can not retrieve the missed one page. For example:
size=0x28006, PAGE_SIZE=0x1000, KASAN_SHADOW_SCALE_SHIFT=3, we will get
shadow_size=0x5000, but actually we need 6 pages.
shadow_size = round_up(size >> KASAN_SHADOW_SCALE_SHIFT, PAGE_SIZE);
This can lead to a kernel crash when kasan is enabled and the value of
mod->core_layout.size or mod->init_layout.size is like above. Because
the shadow memory of X has not been allocated and mapped.
move_module:
ptr = module_alloc(mod->core_layout.size);
...
memset(ptr, 0, mod->core_layout.size); //crashed
Unable to handle kernel paging request at virtual address ffff0fffff97b000
......
Call trace:
__asan_storeN+0x174/0x1a8
memset+0x24/0x48
layout_and_allocate+0xcd8/0x1800
load_module+0x190/0x23e8
SyS_finit_module+0x148/0x180
Link: http://lkml.kernel.org/r/1529659626-12660-1-git-send-email-thunder.leizhen@huawei.com
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Reviewed-by: Dmitriy Vyukov <dvyukov@google.com>
Acked-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Hanjun Guo <guohanjun@huawei.com>
Cc: Libin <huawei.libin@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 26b68dd2f4 ]
Silence warnings (triggered at W=1) by adding relevant __printf attributes.
CC kernel/trace/trace.o
kernel/trace/trace.c: In function ‘__trace_array_vprintk’:
kernel/trace/trace.c:2979:2: warning: function might be possible candidate for ‘gnu_printf’ format attribute [-Wsuggest-attribute=format]
len = vscnprintf(tbuffer, TRACE_BUF_SIZE, fmt, args);
^~~
AR kernel/trace/built-in.o
Link: http://lkml.kernel.org/r/20180308205843.27447-1-malat@debian.org
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 52ee6ef36e ]
The current code does not inspect the return value of skb_to_sgvec. This
can cause a nullptr kernel panic when the malformed sgvec is passed into
the crypto request.
Checking the return value of skb_to_sgvec and skipping decryption if it
is negative fixes this problem.
Fixes: c46234ebb4 ("tls: RX path for ktls")
Acked-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: Doron Roberts-Kedes <doronrk@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3b8d573586 ]
The touch sensors on the 2nd-gen Intuos tablets don't use a 4096x4096
sensor like other similar tablets (3rd-gen Bamboo, Intuos5, etc.).
The incorrect maximum XY values don't normally affect userspace since
touch input from these devices is typically relative rather than
absolute. It does, however, cause problems when absolute distances
need to be measured, e.g. for gesture recognition. Since the resolution
of the touch sensor on these devices is 10 units / mm (versus 100 for
the pen sensor), the proper maximum values can be calculated by simply
dividing by 10.
Fixes: b5fd2a3e92 ("Input: wacom - add support for three new Intuos devices")
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1cef1150ef ]
Gaurav reports that commit:
85f1abe001 ("kthread, sched/wait: Fix kthread_parkme() completion issue")
isn't working for him. Because of the following race:
> controller Thread CPUHP Thread
> takedown_cpu
> kthread_park
> kthread_parkme
> Set KTHREAD_SHOULD_PARK
> smpboot_thread_fn
> set Task interruptible
>
>
> wake_up_process
> if (!(p->state & state))
> goto out;
>
> Kthread_parkme
> SET TASK_PARKED
> schedule
> raw_spin_lock(&rq->lock)
> ttwu_remote
> waiting for __task_rq_lock
> context_switch
>
> finish_lock_switch
>
>
>
> Case TASK_PARKED
> kthread_park_complete
>
>
> SET Running
Furthermore, Oleg noticed that the whole scheduler TASK_PARKED
handling is buggered because the TASK_DEAD thing is done with
preemption disabled, the current code can still complete early on
preemption :/
So basically revert that earlier fix and go with a variant of the
alternative mentioned in the commit. Promote TASK_PARKED to special
state to avoid the store-store issue on task->state leading to the
WARN in kthread_unpark() -> __kthread_bind().
But in addition, add wait_task_inactive() to kthread_park() to ensure
the task really is PARKED when we return from kthread_park(). This
avoids the whole kthread still gets migrated nonsense -- although it
would be really good to get this done differently.
Reported-by: Gaurav Kohli <gkohli@codeaurora.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 85f1abe001 ("kthread, sched/wait: Fix kthread_parkme() completion issue")
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3482d98bbc ]
When a cfs_rq is throttled, parent cfs_rq->nr_running is decreased and
everything happens at cfs_rq level. Currently util_est stays unchanged
in such case and it keeps accounting the utilization of throttled tasks.
This can somewhat make sense as we don't dequeue tasks but only throttled
cfs_rq.
If a task of another group is enqueued/dequeued and root cfs_rq becomes
idle during the dequeue, util_est will be cleared whereas it was
accounting util_est of throttled tasks before. So the behavior of util_est
is not always the same regarding throttled tasks and depends of side
activity. Furthermore, util_est will not be updated when the cfs_rq is
unthrottled as everything happens at cfs_rq level. Main results is that
util_est will stay null whereas we now have running tasks. We have to wait
for the next dequeue/enqueue of the previously throttled tasks to get an
up to date util_est.
Remove the assumption that cfs_rq's estimated utilization of a CPU is 0
if there is no running task so the util_est of a task remains until the
latter is dequeued even if its cfs_rq has been throttled.
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Patrick Bellasi <patrick.bellasi@arm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 7f65ea42eb ("sched/fair: Add util_est on top of PELT")
Link: http://lkml.kernel.org/r/1528972380-16268-1-git-send-email-vincent.guittot@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 512ac999d2 ]
I noticed that cgroup task groups constantly get throttled even
if they have low CPU usage, this causes some jitters on the response
time to some of our business containers when enabling CPU quotas.
It's very simple to reproduce:
mkdir /sys/fs/cgroup/cpu/test
cd /sys/fs/cgroup/cpu/test
echo 100000 > cpu.cfs_quota_us
echo $$ > tasks
then repeat:
cat cpu.stat | grep nr_throttled # nr_throttled will increase steadily
After some analysis, we found that cfs_rq::runtime_remaining will
be cleared by expire_cfs_rq_runtime() due to two equal but stale
"cfs_{b|q}->runtime_expires" after period timer is re-armed.
The current condition to judge clock drift in expire_cfs_rq_runtime()
is wrong, the two runtime_expires are actually the same when clock
drift happens, so this condtion can never hit. The orginal design was
correctly done by this commit:
a9cf55b286 ("sched: Expire invalid runtime")
... but was changed to be the current implementation due to its locking bug.
This patch introduces another way, it adds a new field in both structures
cfs_rq and cfs_bandwidth to record the expiration update sequence, and
uses them to figure out if clock drift happens (true if they are equal).
Signed-off-by: Xunlei Pang <xlpang@linux.alibaba.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Ben Segall <bsegall@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 51f2176d74 ("sched/fair: Fix unlocked reads of some cfs_b->quota/period")
Link: http://lkml.kernel.org/r/20180620101834.24455-1-xlpang@linux.alibaba.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d9c0ffcabd ]
Some people have reported that the warning in sched_tick_remote()
occasionally triggers, especially in favour of some RCU-Torture
pressure:
WARNING: CPU: 11 PID: 906 at kernel/sched/core.c:3138 sched_tick_remote+0xb6/0xc0
Modules linked in:
CPU: 11 PID: 906 Comm: kworker/u32:3 Not tainted 4.18.0-rc2+ #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014
Workqueue: events_unbound sched_tick_remote
RIP: 0010:sched_tick_remote+0xb6/0xc0
Code: e8 0f 06 b8 00 c6 03 00 fb eb 9d 8b 43 04 85 c0 75 8d 48 8b 83 e0 0a 00 00 48 85 c0 75 81 eb 88 48 89 df e8 bc fe ff ff eb aa <0f> 0b eb
+c5 66 0f 1f 44 00 00 bf 17 00 00 00 e8 b6 2e fe ff 0f b6
Call Trace:
process_one_work+0x1df/0x3b0
worker_thread+0x44/0x3d0
kthread+0xf3/0x130
? set_worker_desc+0xb0/0xb0
? kthread_create_worker_on_cpu+0x70/0x70
ret_from_fork+0x35/0x40
This happens when the remote tick applies on an idle task. Usually the
idle_cpu() check avoids that, but it is performed before we lock the
runqueue and it is therefore racy. It was intended to be that way in
order to prevent from useless runqueue locks since idle task tick
callback is a no-op.
Now if the racy check slips out of our hands and we end up remotely
ticking an idle task, the empty task_tick_idle() is harmless. Still
it won't pass the WARN_ON_ONCE() test that ensures rq_clock_task() is
not too far from curr->se.exec_start because update_curr_idle() doesn't
update the exec_start value like other scheduler policies. Hence the
reported false positive.
So let's have another check, while the rq is locked, to make sure we
don't remote tick on an idle task. The lockless idle_cpu() still applies
to avoid unecessary rq lock contention.
Reported-by: Jacek Tomaka <jacekt@dug.com>
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reported-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1530203381-31234-1-git-send-email-frederic@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6897e6ecb3 ]
We found that the original implementation will only use the built-in dtb
pointer instead of the pointer pass from bootloader. This bug is fixed
by this patch.
Signed-off-by: Greentime Hu <greentime@andestech.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 74cb319bd9 ]
pm_runtime_put_sync() gets called everytime in xhci_dbc_stop().
If dbc is not started, this makes the runtime PM counter incorrectly
becomes 0, and calls autosuspend function. Then we'll keep seeing this:
[54664.762220] xhci_hcd 0000:00:14.0: Root hub is not suspended
So only calls pm_runtime_put_sync() when dbc was started.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5dc2d3996a ]
After we change the ipvlan mode from l3 to l2, or vice versa, we only
reset IFF_NOARP flag, but don't flush the ARP table cache, which will
cause eth->h_dest to be equal to eth->h_source in ipvlan_xmit_mode_l2().
Then the message will not come out of host.
Here is the reproducer on local host:
ip link set eth1 up
ip addr add 192.168.1.1/24 dev eth1
ip link add link eth1 ipvlan1 type ipvlan mode l3
ip netns add net1
ip link set ipvlan1 netns net1
ip netns exec net1 ip link set ipvlan1 up
ip netns exec net1 ip addr add 192.168.2.1/24 dev ipvlan1
ip route add 192.168.2.0/24 via 192.168.1.2
ping 192.168.2.2 -c 2
ip netns exec net1 ip link set ipvlan1 type ipvlan mode l2
ping 192.168.2.2 -c 2
Add the same configuration on remote host. After we set the mode to l2,
we could find that the src/dst MAC addresses are the same on eth1:
21:26:06.648565 00:b7:13:ad:d3:05 > 00:b7:13:ad:d3:05, ethertype IPv4 (0x0800), length 98: (tos 0x0, ttl 64, id 58356, offset 0, flags [DF], proto ICMP (1), length 84)
192.168.2.1 > 192.168.2.2: ICMP echo request, id 22686, seq 1, length 64
Fix this by calling dev_change_flags(), which will call netdevice notifier
with flag change info.
v2:
a) As pointed out by Wang Cong, check return value for dev_change_flags() when
change dev flags.
b) As suggested by Stefano and Sabrina, move flags setting before l3mdev_ops.
So we don't need to redo ipvlan_{, un}register_nf_hook() again in err path.
Reported-by: Jianlin Shi <jishi@redhat.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Fixes: 2ad7bf3638 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 08b393d01c ]
Since the following commit:
cd77849a69 ("objtool: Fix GCC 8 cold subfunction detection for aliased functions")
... if the kernel is built with EXTRA_CFLAGS='-fno-reorder-functions',
objtool can get stuck in an infinite loop.
That flag causes the new GCC 8 cold subfunctions to be placed in .text
instead of .text.unlikely. But it also has an unfortunate quirk: in the
symbol table, the subfunction (e.g., nmi_panic.cold.7) is nested inside
the parent (nmi_panic).
That function overlap confuses objtool, and causes it to get into an
infinite loop in next_insn_same_func(). Here's Allan's description of
the loop:
"Objtool iterates through the instructions in nmi_panic using
next_insn_same_func. Once it reaches the end of nmi_panic at 0x534 it
jumps to 0x528 as that's the start of nmi_panic.cold.7. However, since
the instructions starting at 0x528 are still associated with nmi_panic
objtool will get stuck in a loop, continually jumping back to 0x528
after reaching 0x534."
Fix it by shortening the length of the parent function so that the
functions no longer overlap.
Reported-and-analyzed-by: Allan Xavier <allan.x.xavier@oracle.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Allan Xavier <allan.x.xavier@oracle.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/9e704c52bee651129b036be14feda317ae5606ae.1530136978.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ecd60532e0 ]
Booting a ColdFire m68k core with MMU enabled causes a "bad page state"
oops since commit 1d40a5ea01 ("mm: mark pages in use for page tables"):
BUG: Bad page state in process sh pfn:01ce2
page:004fefc8 count:0 mapcount:-1024 mapping:00000000 index:0x0
flags: 0x0()
raw: 00000000 00000000 00000000 fffffbff 00000000 00000100 00000200 00000000
raw: 039c4000
page dumped because: nonzero mapcount
Modules linked in:
CPU: 0 PID: 22 Comm: sh Not tainted 4.17.0-07461-g1d40a5ea01d5 #13
Fix by calling pgtable_page_dtor() in our __pte_free_tlb() code path,
so that the PG_table flag is cleared before we free the pte page.
Note that I had to change the type of pte_free() to be static from
extern. Otherwise you get a lot of warnings like this:
./arch/m68k/include/asm/mcf_pgalloc.h:80:2: warning: ‘pgtable_page_dtor’ is static but used in inline function ‘pte_free’ which is not static
pgtable_page_dtor(page);
^
And making it static is consistent with our use of this in the other
m68k pgalloc definitions of pte_free().
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
CC: Matthew Wilcox <willy@infradead.org>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a068b94d74 ]
Building the kernel with CONFIG_THUMB2_KERNEL=y and
CONFIG_CRYPTO_SPECK_NEON set fails with the following errors:
arch/arm/crypto/speck-neon-core.S: Assembler messages:
arch/arm/crypto/speck-neon-core.S:419: Error: r13 not allowed here -- `bic sp,#0xf'
arch/arm/crypto/speck-neon-core.S:423: Error: r13 not allowed here -- `bic sp,#0xf'
arch/arm/crypto/speck-neon-core.S:427: Error: r13 not allowed here -- `bic sp,#0xf'
arch/arm/crypto/speck-neon-core.S:431: Error: r13 not allowed here -- `bic sp,#0xf'
The problem is that the 'bic' instruction can't operate on the 'sp'
register in Thumb2 mode. Fix it by using a temporary register. This
isn't in the main loop, so the performance difference is negligible.
This also matches what aes-neonbs-core.S does.
Reported-by: Stefan Agner <stefan@agner.ch>
Fixes: ede9622162 ("crypto: arm/speck - add NEON-accelerated implementation of Speck-XTS")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ae15a41a64 ]
Originally in patch e6d20c55a4 ("openrisc: entry: Fix delay slot
detection") I fixed delay slot detection, but only for QEMU. We missed
that hardware delay slot detection using delay slot exception flag (DSX)
was still broken. This was because QEMU set the DSX flag in both
pre-exception supervision register (ESR) and supervision register (SR)
register, but on real hardware the DSX flag is only set on the SR
register during exceptions.
Fix this by carrying the DSX flag into the SR register during exception.
We also update the DSX flag read locations to read the value from the SR
register not the pt_regs SR register which represents ESR. The ESR
should never have the DSX flag set.
In the process I updated/removed a few comments to match the current
state. Including removing a comment saying that the DSX detection logic
was inefficient and needed to be rewritten.
I have tested this on QEMU with a patch ensuring it matches the hardware
specification.
Link: https://lists.gnu.org/archive/html/qemu-devel/2018-07/msg00000.html
Fixes: e6d20c55a4 ("openrisc: entry: Fix delay slot detection")
Signed-off-by: Stafford Horne <shorne@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1273c253c3 ]
Commit 546eb0317c "libnvdimm, pmem: Do not flush power-fail protected CPU caches"
fixed the write_cache detection to correctly show the lack of a write
cache based on the platform capabilities described in the ACPI NFIT. The
nfit_test unit tests expected a write cache to be present, so change the
nfit test namespaces to only advertise a persistence domain limited to
the memory controller. This allows the kernel to show a write_cache
attribute, and the test behaviour remains unchanged.
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c1985cefd8 ]
cmd_rc is passed in by reference to the acpi_nfit_ctl() function and the
caller expects a value returned. However, when the package is pass through
via the ND_CMD_CALL command, cmd_rc is not touched. Make sure cmd_rc is
always set.
Fixes: aef2533822 ("libnvdimm, nfit: centralize command status translation")
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d025da9eb1 ]
commit e830baa9c3 ("qeth: restore device features after recovery") and
commit ce34435641 ("s390/qeth: rely on kernel for feature recovery")
made sure that the HW functions for device features get re-programmed
after recovery.
But we missed that the same handling is also required when a card is
first set offline (destroying all HW context), and then online again.
Fix this by moving the re-enable action out of the recovery-only path.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 595e802e53 ]
The DPAA HW requires that at least 256 bytes from the start of the
first scatter-gather table entry are allocated and accessible. The
hardware reads the maximum size the table can have in one access,
thus requiring that the allocation and mapping to be done for the
maximum size of 256B even if there is a smaller number of entries
in the table.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b95f6fbc8e ]
The FMan hardware parser needs to be configured to remove the
short frame padding from the checksum calculation, otherwise
short UDP and TCP frames are likely to be marked as having a
bad checksum.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 484c016d93 ]
Driver performs the internal reload when it receives tx-timeout event from
the OS. Internal reload might fail in some scenarios e.g., fatal HW issues.
In such cases OS still see the link, which would result in undesirable
functionalities such as re-generation of tx-timeouts.
The patch addresses this issue by indicating the link-down to OS when
tx-timeout is detected, and keeping the link in down state till the
internal reload is successful.
Please consider applying it to 'net' branch.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3dc6ddfedc ]
The call to of_get_next_child() returns a node pointer with refcount
incremented thus it must be explicitly decremented here in the error
path and after the last usage.
Fixes: d3c68e0a7e ("PCI: faraday: Add Faraday Technology FTPCI100 PCI Host Bridge driver")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 342639d996 ]
The call to of_get_next_child() returns a node pointer with
refcount incremented thus it must be explicitly decremented
here after the last usage.
Fixes: ab597d35ef ("PCI: xilinx-nwl: Add support for Xilinx NWL PCIe Host Controller")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8c3f9bd851 ]
The call to of_get_next_child() returns a node pointer with refcount
incremented thus it must be explicitly decremented here after the last
usage.
Fixes: 8961def568 ("PCI: xilinx: Add Xilinx AXI PCIe Host Bridge IP driver")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
[lorenzo.pieralisi@arm.com: reworked commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f605ce5eb2 ]
If we would ever fail in the bpf_jit_prog() pass that writes the
actual insns to the image after we got header via bpf_jit_binary_alloc()
then we also need to make sure to free it through bpf_jit_binary_free()
again when bailing out. Given we had prior bpf_jit_prog() passes to
initially probe for clobbered registers, program size and to fill in
addrs arrray for jump targets, this is more of a theoretical one,
but at least make sure this doesn't break with future changes.
Fixes: 0546231057 ("s390/bpf: Add s390x eBPF JIT compiler backend")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1f57f8d442 ]
Some devices have different queue limits depending on the type of IO. A
classic case is SATA NCQ, where some commands can queue, but others
cannot. If we have NCQ commands inflight and encounter a non-queueable
command, the driver returns busy. Currently we attempt to dispatch more
from the scheduler, if we were able to queue some commands. But for the
case where we ended up stopping due to BUSY, we should not attempt to
retrieve more from the scheduler. If we do, we can get into a situation
where we attempt to queue a non-queueable command, get BUSY, then
successfully retrieve more commands from that scheduler and queue those.
This can repeat forever, starving the non-queuable command indefinitely.
Fix this by NOT attempting to pull more commands from the scheduler, if
we get a BUSY return. This should also be more optimal in terms of
letting requests stay in the scheduler for as long as possible, if we
get a BUSY due to the regular out-of-tags condition.
Reviewed-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dd209ef809 ]
Fix following issues related to planar YUV pixel format configuration:
- NV16/61 modes were incorrectly programmed as NV12/21,
- YVU420 was programmed as YUV420 on source,
- YVU420 and YUV422 were programmed as YUV420 on output.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 188f60ab8e ]
Commit 9757235f45, "nl80211: correct checks for
NL80211_MESHCONF_HT_OPMODE value") relaxed the range for the HT
operation field in meshconf, while also adding checks requiring
the non-greenfield and non-ht-sta bits to be set in certain
circumstances. The latter bit is actually reserved for mesh BSSes
according to Table 9-168 in 802.11-2016, so in fact it should not
be set.
wpa_supplicant sets these bits because the mesh and AP code share
the same implementation, but authsae does not. As a result, some
meshconf updates from authsae which set only the NONHT_MIXED
protection bits were being rejected.
In order to avoid breaking userspace by changing the rules again,
simply accept the values with or without the bits set, and mask
off the reserved bit to match the spec.
While in here, update the 802.11-2012 reference to 802.11-2016.
Fixes: 9757235f45 ("nl80211: correct checks for NL80211_MESHCONF_HT_OPMODE value")
Cc: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Bob Copeland <bobcopeland@fb.com>
Reviewed-by: Masashi Honma <masashi.honma@gmail.com>
Reviewed-by: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e7441c9274 ]
On pre-emption enabled kernels the following print was being seen due to
missing local_bh_disable/local_bh_enable calls. mac80211 assumes that
pre-emption is disabled in the data path.
BUG: using smp_processor_id() in preemptible [00000000] code: iwd/517
caller is __ieee80211_subif_start_xmit+0x144/0x210 [mac80211]
[...]
Call Trace:
dump_stack+0x5c/0x80
check_preemption_disabled.cold.0+0x46/0x51
__ieee80211_subif_start_xmit+0x144/0x210 [mac80211]
Fixes: 9118064914 ("mac80211: Add support for tx_control_port")
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
[commit message rewrite, fixes tag]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bda3153998 ]
During assemble, the spare marked for replacement is not checked.
conf->fullsync cannot be updated to be 1. As a result, recovery will
treat it as a clean array. All recovering sectors are skipped. Original
device is replaced with the not-recovered spare.
mdadm -C /dev/md0 -l10 -n4 -pn2 /dev/loop[0123]
mdadm /dev/md0 -a /dev/loop4
mdadm /dev/md0 --replace /dev/loop0
mdadm -S /dev/md0 # stop array during recovery
mdadm -A /dev/md0 /dev/loop[01234]
After reassemble, you can see recovery go on, but it completes
immediately. In fact, recovery is not actually processed.
To solve this problem, we just add the missing logics for replacment
spares. (In raid1.c or raid5.c, they have already been checked.)
Reported-by: Alex Chen <alexchen@synology.com>
Reviewed-by: Alex Wu <alexwu@synology.com>
Reviewed-by: Chung-Chiang Cheng <cccheng@synology.com>
Signed-off-by: BingJing Chang <bingjingc@synology.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9191fc2a43 ]
In the case of Station connects to AP with narrower bandwidth at beginning.
And later the AP changes the bandwidth to winder bandwidth, the AP will
beacon with wider bandwidth IE, eg VHT20->VHT40->VHT80 or VHT40->VHT80.
Since the supported BANDWIDTH will be limited by the PHYMODE, so while
Station receives the bandwidth change request, it will also need to
reconfigure the PHYMODE setting to firmware instead of just configuring
the BANDWIDTH info, otherwise it'll trigger a firmware crash with
non-support bandwidth.
The issue was observed in WLAN.RM.4.4.1-00051-QCARMSWP-1, QCA6174 with
below scenario:
AP xxx changed bandwidth, new config is 5200 MHz, width 2 (5190/0 MHz)
disconnect from AP xxx for new auth to yyy
RX ReassocResp from xxx (capab=0x1111 status=0 aid=102)
associated
....
AP xxx changed bandwidth, new config is 5200 MHz, width 2 (5190/0 MHz)
AP xxx changed bandwidth, new config is 5200 MHz, width 3 (5210/0 MHz)
....
firmware register dump:
[00]: 0x05030000 0x000015B3 0x00987291 0x00955B31
[04]: 0x00987291 0x00060730 0x00000004 0x00000001
[08]: 0x004089F0 0x00955A00 0x000A0B00 0x00400000
[12]: 0x00000009 0x00000000 0x00952CD0 0x00952CE6
[16]: 0x00952CC4 0x0098E25F 0x00000000 0x0091080D
[20]: 0x40987291 0x0040E7A8 0x00000000 0x0041EE3C
[24]: 0x809ABF05 0x0040E808 0x00000000 0xC0987291
[28]: 0x809A650C 0x0040E948 0x0041FE40 0x004345C4
[32]: 0x809A5C63 0x0040E988 0x0040E9AC 0x0042D1A8
[36]: 0x8091D252 0x0040E9A8 0x00000002 0x00000001
[40]: 0x809FDA9D 0x0040EA58 0x0043D554 0x0042D554
[44]: 0x809F8B22 0x0040EA78 0x0043D554 0x00000001
[48]: 0x80911210 0x0040EAC8 0x00000010 0x004041D0
[52]: 0x80911154 0x0040EB28 0x00400000 0x00000000
[56]: 0x8091122D 0x0040EB48 0x00000000 0x00400600
Reported-by: Rouven Czerwinski <rouven@czerwinskis.de>
Tested-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Ryan Hsu <ryanhsu@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e3f329c600 ]
The reported residue is already calculated in BURST unit granularity, so
advertise this capability properly to other devices in the system.
Fixes: aee4d1fac8 ("dmaengine: pl330: improve pl330_tx_status() function")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1c38f4afd5 ]
meson-gxl-mali.dtsi is only used on GXL SoCs. Thus it should use the GXL
specific compatible string instead of the GXBB one.
For now this is purely cosmetic since the (out-of-tree) lima driver for
this GPU currently uses the "arm,mali-450" match instead of the SoC
specific one. However, update the .dts to match the documentation since
this driver behavior might change in the future.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6d28d57751 ]
Like the odroid-c2 and wetek, the s400 uses the RTL8211F and seems to
suffer from the kind of stability issue.
Doing an iperf3 download test, we can see a significant number of LPI
interrupts on the tx path. After a short while (5 to 15 seconds), the
network connection dies. If using rootfs over NFS, the connection may
also break during the boot sequence.
We still don't have a real explanation for this problem so let's disable
EEE once again.
Fixes: f6f6ac914b ("ARM64: dts: meson-axg: enable ethernet for A113D S400 board")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 429388682d ]
The implementation of flush_icache_range() includes instruction sequences
which are themselves patched at runtime, so it is not safe to call from
the patching framework.
This patch reworks the alternatives cache-flushing code so that it rolls
its own internal D-cache maintenance using DC CIVAC before invalidating
the entire I-cache after all alternatives have been applied at boot.
Modules don't cause any issues, since flush_icache_range() is safe to
call by the time they are loaded.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reported-by: Rohit Khanna <rokhanna@nvidia.com>
Cc: Alexander Van Brunt <avanbrunt@nvidia.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 86676c4685 ]
This patch fixes wrong name of headphone widget for receiving events
of insert/remove headphone plug from simple-card or audio-graph-card.
If we use wrong widget name then we get warning messages such as
"asoc-audio-graph-card sound: ASoC: DAPM unknown pin Headphones"
when the plug is inserted or removed from headphone jack.
Fixes: fb21a0acaa ("arm64: dts: uniphier: add sound node")
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3eb1b955cd ]
The intc #interrupt-cells is equal to 1. Currently gpio
node has 2 cells per IRQ which is wrong. Remove the additional
cell for each of the interrupts.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Fixes: 2e38b946dc ("ARM: davinci: da850: add GPIO DT node")
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c809195f55 ]
The RDS core module creates rds_connections based on callbacks
from rds_loop_transport when sending/receiving packets to local
addresses.
These connections will need to be cleaned up when they are
created from a netns that is not init_net, and that netns is deleted.
Add the changes aligned with the changes from
commit ebeeb1ad9b ("rds: tcp: use rds_destroy_pending() to synchronize
netns/module teardown and rds connection/workq management") for
rds_loop_transport
Reported-and-tested-by: syzbot+4c20b3866171ce8441d2@syzkaller.appspotmail.com
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a8d70a054a ]
In smartnic env, if the host (PF) driver is not an e-switch manager, we
are not allowed to apply eswitch ports setups such as vlan (VST),
spoof-checks, min/max rate or state.
Make sure we are eswitch manager when coming to issue these callbacks
and err otherwise.
Also fix the definition of ESW_ALLOWED to rely on eswitch_manager
capability and on the vport_group_manger.
Operations on the VF nic vport context, such as setting a mac or reading
the vport counters are allowed to the PF in this scheme.
The modify nic vport guid code was modified to omit checking the
nic_vport_node_guid_modify eswitch capability.
The reason for doing so is that modifying node guid requires vport group
manager capability, and there's no need to check further capabilities.
1. set_vf_vlan - disallowed
2. set_vf_spoofchk - disallowed
3. set_vf_mac - allowed
4. get_vf_config - allowed
5. set_vf_trust - disallowed
6. set_vf_rate - disallowed
7. get_vf_stat - allowed
8. set_vf_link_state - disallowed
Fixes: f942380c12 ('net/mlx5: E-Switch, Vport ingress/egress ACLs rules for spoofchk')
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Tested-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dffd22aed2 ]
When proc_dostring() is called with a non-zero offset in strict mode, it
doesn't just write to the ->data buffer, it also reads. Make sure it
doesn't read uninitialized data.
Fixes: c6ac37d8d8 ("netfilter: nf_log: fix error on write NONE to [...]")
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1b6fe9798a ]
When booting from MMC/SD in rw mode on DA850 EVM, the system
crashes because the write protect pin should be active high
and not active low. This patch fixes the polarity of the WP pin.
Fixes: bdf0e8364f ("ARM: davinci: da850-evm: use gpio descriptor for mmc pins")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 90f26cc6bb ]
The commit 4e88d4c083 ("usb: add a flag to skip PHY
initialization to struct usb_hcd") delete the assignment
for hcd->usb_phy, it causes usb_phy_notify_connect{disconnect)
are not called, the USB PHY driver is not notified of hot plug
event, then the disconnection will not be detected by hardware.
Fixes: 4e88d4c083 ("usb: add a flag to skip PHY initialization
to struct usb_hcd")
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reported-by: Mats Karrman <mats.dev.list@gmail.com>
Tested-by: Mats Karrman <mats.dev.list@gmail.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 983107072b ]
Currently we can hit following assert when running numa bench:
$ perf bench numa mem -p 3 -t 1 -P 512 -s 100 -zZ0cm --thp 1
perf: bench/numa.c:1577: __bench_numa: Assertion `!(!(((wait_stat) & 0x7f) == 0))' failed.
The assertion is correct, because we hit the SIGFPE in following line:
Thread 2.2 "thread 0/0" received signal SIGFPE, Arithmetic exception.
[Switching to Thread 0x7fffd28c6700 (LWP 11750)]
0x000.. in worker_thread (__tdata=0x7.. ) at bench/numa.c:1257
1257 td->speed_gbs = bytes_done / (td->runtime_ns / NSEC_PER_SEC) / 1e9;
We don't check if the runtime is actually bigger than 1 second,
and thus this might end up with zero division within FPU.
Adding the check to prevent this.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20180620094036.17278-1-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c6555c1457 ]
Arnaldo reported the perf build failure with latest llvm/clang compiler
(7.0).
$ make LIBCLANGLLVM=1 -C tools/perf/
<SNIP>
CC /tmp/tmp.t53Qo38zci/tests/kmod-path.o
util/c++/clang.cpp: In function ‘std::unique_ptr<llvm::SmallVectorImpl<char> >
perf::getBPFObjectFromModule(llvm::Module*)’:
util/c++/clang.cpp:150:43: error: no matching function for call to
‘llvm::TargetMachine::addPassesToEmitFile(llvm::legacy::PassManager&,
llvm::raw_svector_ostream&, llvm::TargetMachine::CodeGenFileType)’
TargetMachine::CGFT_ObjectFile)) {
^
In file included from util/c++/clang.cpp:25:0:
/usr/local/include/llvm/Target/TargetMachine.h:254:16: note: candidate:
virtual bool llvm::TargetMachine::addPassesToEmitFile(
llvm::legacy::PassManagerBase&, llvm::raw_pwrite_stream&,
llvm::raw_pwrite_stream*, llvm::TargetMachine::CodeGenFileType, bool,
llvm::MachineModuleInfo*)
virtual bool addPassesToEmitFile(PassManagerBase &, raw_pwrite_stream &,
^~~~~~~~~~~~~~~~~~~
/usr/local/include/llvm/Target/TargetMachine.h:254:16: note:
candidate expects 6 arguments, 3 provided
mv: cannot stat '/tmp/tmp.t53Qo38zci/util/c++/.clang.o.tmp': No such file or directory
make[7]: *** [/home/acme/git/perf/tools/build/Makefile.build:101:
/tmp/tmp.t53Qo38zci/util/c++/clang.o] Error 1
make[6]: *** [/home/acme/git/perf/tools/build/Makefile.build:139: c++] Error 2
make[5]: *** [/home/acme/git/perf/tools/build/Makefile.build:139: util] Error 2
make[5]: *** Waiting for unfinished jobs....
CC /tmp/tmp.t53Qo38zci/tests/thread-map.o
The function addPassesToEmitFile signature changed in llvm 7.0 and such
a change caused the failure. This patch fixed the issue with using
proper function signatures under different compiler versions.
Reported-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Yonghong Song <yhs@fb.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexei Starovoitov <ast@fb.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/20180616174739.1076733-1-yhs@fb.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 933ccf2002 ]
Add missing error handling for parse_events calls in test_event function
that led to following segfault on s390:
running test 52 'intel_pt//u'
perf: Segmentation fault
...
/lib64/libc.so.6(vasprintf+0xe6) [0x3fffca3f106]
/lib64/libc.so.6(asprintf+0x46) [0x3fffca1aa96]
./perf(parse_events_add_pmu+0xb8) [0x80132088]
./perf(parse_events_parse+0xc62) [0x8019529a]
./perf(parse_events+0x98) [0x801341c0]
./perf(test__parse_events+0x48) [0x800cd140]
./perf(cmd_test+0x26a) [0x800bd44a]
test child interrupted
Adding the struct parse_events_error argument to parse_events call. Also
adding parse_events_print_error to get more details on the parsing
failures, like:
# perf test 6 -v
running test 52 'intel_pt//u'failed to parse event 'intel_pt//u', err 1, str 'Cannot find PMU `intel_pt'. Missing kernel support?'
event syntax error: 'intel_pt//u'
\___ Cannot find PMU `intel_pt'. Missing kernel support?
Committer note:
Use named initializers in the struct parse_events_error variable to
avoid breaking the build on centos5, 6 and others with a similar gcc:
cc1: warnings being treated as errors
tests/parse-events.c: In function 'test_event':
tests/parse-events.c:1696: error: missing initializer
tests/parse-events.c:1696: error: (near initialization for 'err.str')
Reported-by: Kim Phillips <kim.phillips@arm.com>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Kim Phillips <kim.phillips@arm.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Richter <tmricht@linux.ibm.com>
Link: http://lkml.kernel.org/r/20180611093422.1005-1-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 143c99f6ac ]
For some cases, the callchain provided by the kernel may be empty. So,
the callchain ip filtering code will cause a crash if we do not check
whether the struct ip_callchain pointer is NULL before accessing any
members.
This can be observed on a powerpc64le system running Fedora 27 as shown
below.
# perf record -b -e cycles:u ls
Before:
# perf report --branch-history
perf: Segmentation fault
-------- backtrace --------
perf[0x1027615c]
linux-vdso64.so.1(__kernel_sigtramp_rt64+0x0)[0x7fff856304d8]
perf(arch_skip_callchain_idx+0x44)[0x10257c58]
perf[0x1017f2e4]
perf(thread__resolve_callchain+0x124)[0x1017ff5c]
perf(sample__resolve_callchain+0xf0)[0x10172788]
...
After:
# perf report --branch-history
Samples: 25 of event 'cycles:u', Event count (approx.): 2306870
Overhead Source:Line Symbol Shared Object
+ 11.60% _init+35736 [.] _init ls
+ 9.84% strcoll_l.c:137 [.] __strcoll_l libc-2.26.so
+ 9.16% memcpy.S:175 [.] __memcpy_power7 libc-2.26.so
+ 9.01% gconv_charset.h:54 [.] _nl_find_locale libc-2.26.so
+ 8.87% dl-addr.c:52 [.] _dl_addr libc-2.26.so
+ 8.83% _init+236 [.] _init ls
...
Reported-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Signed-off-by: Sandipan Das <sandipan@linux.ibm.com>
Acked-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/20180611104049.11048-1-sandipan@linux.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b930e62ecd ]
On s390 this test case fails because the socket identifiction numbers
assigned to the CPU are higher than the CPU identification numbers.
F/ix this by adding the platform architecture into the perf data header
flag information. This helps identifiing the test platform and handles
s390 specifics in process_cpu_topology().
Before:
[root@p23lp27 perf]# perf test -vvvvv -F 39
39: Session topology :
--- start ---
templ file: /tmp/perf-test-iUv755
socket_id number is too big.You may need to upgrade the perf tool.
---- end ----
Session topology: Skip
[root@p23lp27 perf]#
After:
[root@p23lp27 perf]# perf test -vvvvv -F 39
39: Session topology :
--- start ---
templ file: /tmp/perf-test-8X8VTs
CPU 0, core 0, socket 6
CPU 1, core 1, socket 3
---- end ----
Session topology: Ok
[root@p23lp27 perf]#
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Reviewed-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fixes: c84974ed9f ("perf test: Add entry to test cpu topology")
Link: http://lkml.kernel.org/r/20180611073153.15592-2-tmricht@linux.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0176622953 ]
On s390 the socket identifier assigned to a CPU identifier is random and
(depending on the configuration of the LPAR) may be higher than the CPU
identifier. This is currently not supported.
Fix this by allowing arbitrary socket identifiers being assigned to
CPU id.
Output before:
[root@p23lp27 perf]# ./perf report --header -I -v
...
socket_id number is too big.You may need to upgrade the perf tool.
Error:
The perf.data file has no samples!
# ========
# captured on : Tue May 29 09:29:57 2018
# header version : 1
...
# Core ID and Socket ID information is not available
...
[root@p23lp27 perf]#
Output after:
[root@p23lp27 perf]# ./perf report --header -I -v
...
Error:
The perf.data file has no samples!
# ========
# captured on : Tue May 29 09:29:57 2018
# header version : 1
...
# CPU 0: Core ID 0, Socket ID 6
# CPU 1: Core ID 1, Socket ID 3
# CPU 2: Core ID -1, Socket ID -1
...
[root@p23lp27 perf]#
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Reviewed-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Link: http://lkml.kernel.org/r/20180611073153.15592-1-tmricht@linux.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b2d00d7c61 ]
The line numers for if-entries in the menu tree are off by one or more
lines which is confusing when debugging for correctness of unrelated changes.
According to the git log, commit a02f0570ae (kconfig: improve
error handling in the parser) was the last one that changed that part
of the parser and replaced
"if_entry: T_IF expr T_EOL"
by
"if_entry: T_IF expr nl"
but the commit message does not state why this has been done.
When reverting that part of the commit, only the line numers are
corrected (checked with cdebug = DEBUG_PARSE in zconf.y), otherwise
the menu tree remains unchanged (checked with zconfdump() enabled in
conf.c).
An example for the corrected line numbers:
drivers/soc/Kconfig:15:source drivers/soc/tegra/Kconfig
drivers/soc/tegra/Kconfig:4:if
drivers/soc/tegra/Kconfig:6:if
changes to:
drivers/soc/Kconfig:15:source drivers/soc/tegra/Kconfig
drivers/soc/tegra/Kconfig:1:if
drivers/soc/tegra/Kconfig:4:if
Signed-off-by: Dirk Gouders <dirk@gouders.net>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 36eb93509c ]
Initialize the 'err' variate to remove the build warning,
the warning is shown as below:
drivers/usb/host/xhci-tegra.c: In function 'tegra_xusb_mbox_thread':
drivers/usb/host/xhci-tegra.c:552:6: warning: 'err' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/host/xhci-tegra.c:482:6: note: 'err' was declared here
Fixes: e84fce0f88 ("usb: xhci: Add NVIDIA Tegra XUSB controller driver")
Signed-off-by: Dongjiu Geng <gengdongjiu@huawei.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 68d676a089 ]
Stopping offload completely if replace of program failed dates
back to days of transparent offload. Back then we wanted to
silently fall back to the in-driver processing. Today we mark
programs for offload when they are loaded into the kernel, so
the transparent offload is no longer a reality.
Flags check in the driver will only allow replace of a driver
program with another driver program or an offload program with
another offload program.
When driver program is replaced stopping offload is a no-op,
because driver program isn't offloaded. When replacing
offloaded program if the offload fails the entire operation
will fail all the way back to user space and we should continue
using the old program. IOW when replacing a driver program
stopping offload is unnecessary and when replacing offloaded
program - it's a bug, old program should continue to run.
In practice this bug would mean that if offload operation was to
fail (either due to FW communication error, kernel OOM or new
program being offloaded but for a different netdev) driver
would continue reporting that previous XDP program is offloaded
but in fact no program will be loaded in hardware. The failure
is fairly unlikely (found by inspection, when working on the code)
but it's unpleasant.
Backport note: even though the bug was introduced in commit
cafa92ac25 ("nfp: bpf: add support for XDP_FLAGS_HW_MODE"),
this fix depends on commit 441a33031f ("net: xdp: don't allow
device-bound programs in driver mode"), so this fix is sufficient
only in v4.15 or newer. Kernels v4.13.x and v4.14.x do need to
stop offload if it was transparent/opportunistic, i.e. if
XDP_FLAGS_HW_MODE was not set on running program.
Fixes: cafa92ac25 ("nfp: bpf: add support for XDP_FLAGS_HW_MODE")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c9a4c63888 ]
The kernel may spew a WARNING with UBSAN undefined behavior at
handling ALSA sequencer ioctl SNDRV_SEQ_IOCTL_QUERY_NEXT_CLIENT:
UBSAN: Undefined behaviour in sound/core/seq/seq_clientmgr.c:2007:14
signed integer overflow:
2147483647 + 1 cannot be represented in type 'int'
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x122/0x1c8 lib/dump_stack.c:113
ubsan_epilogue+0x12/0x86 lib/ubsan.c:159
handle_overflow+0x1c2/0x21f lib/ubsan.c:190
__ubsan_handle_add_overflow+0x2a/0x31 lib/ubsan.c:198
snd_seq_ioctl_query_next_client+0x1ac/0x1d0 sound/core/seq/seq_clientmgr.c:2007
snd_seq_ioctl+0x264/0x3d0 sound/core/seq/seq_clientmgr.c:2144
....
It happens only when INT_MAX is passed there, as we're incrementing it
unconditionally. So the fix is trivial, check the value with
INT_MAX. Although the bug itself is fairly harmless, it's better to
fix it so that fuzzers won't hit this again later.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=200211
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dc0f0a026d ]
When kcs_bmc_handle_event calls kcs_force_abort function to handle the
not open (no user running) KCS channel transaction, the returned status
value -ENODEV causes the low level IRQ handler indicating that the irq
was not for him by returning IRQ_NONE. After some time, this IRQ will
be treated to be spurious one, and the exception dump happens.
irq 30: nobody cared (try booting with the "irqpoll" option)
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.10.15-npcm750 #1
Hardware name: NPCMX50 Chip family
[<c010b264>] (unwind_backtrace) from [<c0106930>] (show_stack+0x20/0x24)
[<c0106930>] (show_stack) from [<c03dad38>] (dump_stack+0x8c/0xa0)
[<c03dad38>] (dump_stack) from [<c0168810>] (__report_bad_irq+0x3c/0xdc)
[<c0168810>] (__report_bad_irq) from [<c0168c34>] (note_interrupt+0x29c/0x2ec)
[<c0168c34>] (note_interrupt) from [<c0165c80>] (handle_irq_event_percpu+0x5c/0x68)
[<c0165c80>] (handle_irq_event_percpu) from [<c0165cd4>] (handle_irq_event+0x48/0x6c)
[<c0165cd4>] (handle_irq_event) from [<c0169664>] (handle_fasteoi_irq+0xc8/0x198)
[<c0169664>] (handle_fasteoi_irq) from [<c016529c>] (__handle_domain_irq+0x90/0xe8)
[<c016529c>] (__handle_domain_irq) from [<c01014bc>] (gic_handle_irq+0x58/0x9c)
[<c01014bc>] (gic_handle_irq) from [<c010752c>] (__irq_svc+0x6c/0x90)
Exception stack(0xc0a01de8 to 0xc0a01e30)
1de0: 00002080 c0a6fbc0 00000000 00000000 00000000 c096d294
1e00: 00000000 00000001 dc406400 f03ff100 00000082 c0a01e94 c0a6fbc0 c0a01e38
1e20: 00200102 c01015bc 60000113 ffffffff
[<c010752c>] (__irq_svc) from [<c01015bc>] (__do_softirq+0xbc/0x358)
[<c01015bc>] (__do_softirq) from [<c011c798>] (irq_exit+0xb8/0xec)
[<c011c798>] (irq_exit) from [<c01652a0>] (__handle_domain_irq+0x94/0xe8)
[<c01652a0>] (__handle_domain_irq) from [<c01014bc>] (gic_handle_irq+0x58/0x9c)
[<c01014bc>] (gic_handle_irq) from [<c010752c>] (__irq_svc+0x6c/0x90)
Exception stack(0xc0a01ef8 to 0xc0a01f40)
1ee0: 00000000 000003ae
1f00: dcc0f338 c0111060 c0a00000 c0a0cc44 c0a0cbe4 c0a1c22b c07bc218 00000001
1f20: dcffca40 c0a01f54 c0a01f58 c0a01f48 c0103524 c0103528 60000013 ffffffff
[<c010752c>] (__irq_svc) from [<c0103528>] (arch_cpu_idle+0x48/0x4c)
[<c0103528>] (arch_cpu_idle) from [<c0681390>] (default_idle_call+0x30/0x3c)
[<c0681390>] (default_idle_call) from [<c0156f24>] (do_idle+0xc8/0x134)
[<c0156f24>] (do_idle) from [<c015722c>] (cpu_startup_entry+0x28/0x2c)
[<c015722c>] (cpu_startup_entry) from [<c067ad74>] (rest_init+0x84/0x88)
[<c067ad74>] (rest_init) from [<c0900d44>] (start_kernel+0x388/0x394)
[<c0900d44>] (start_kernel) from [<0000807c>] (0x807c)
handlers:
[<c041c5dc>] npcm7xx_kcs_irq
Disabling IRQ #30
It needs to change the returned status from -ENODEV to 0. The -ENODEV
was originally used to tell the low level IRQ handler that no user was
running, but not consider the IRQ handling desgin.
And multiple KCS channels share one IRQ handler, it needs to check the
IBF flag before doing force abort. If the IBF is set, after handling,
return 0 to low level IRQ handler to indicate that the IRQ is handled.
Signed-off-by: Haiyue Wang <haiyue.wang@linux.intel.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 13399ff25f ]
According to IIO ABI relative humidity reading should be
returned in milli percent.
This patch addresses that by applying proper scaling and
returning integer instead of fractional format type specifier.
Note that the fixes tag is before the driver was heavily refactored
to introduce spi support, so the patch won't apply that far back.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Fixes: 14beaa8f5a ("iio: pressure: bmp280: add humidity support")
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a44ebeff6b ]
When a (broken) node wrongly sends multicast TT entries with a ROAM
flag then this causes any receiving node to drop all entries for the
same multicast MAC address announced by other nodes, leading to
packet loss.
Fix this DoS vector by only storing TT sync flags. For multicast TT
non-sync'ing flag bits like ROAM are unused so far anyway.
Fixes: 1d8ab8d3c1 ("batman-adv: Modified forwarding behaviour for multicast packets")
Reported-by: Leonardo Mörlein <me@irrelefant.net>
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4a519b83da ]
Since commit 54e22f265e ("batman-adv: fix TT sync flag inconsistencies")
TT sync flags and TT non-sync'd flags are supposed to be stored
separately.
The previous patch missed to apply this separation on a TT entry with
only a single TT orig entry.
This is a minor fix because with only a single TT orig entry the DDoS
issue the former patch solves does not apply.
Fixes: 54e22f265e ("batman-adv: fix TT sync flag inconsistencies")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6da7be7d24 ]
batman-adv is creating special debugfs directories in the init
net_namespace for each created soft-interface (batadv net_device). But it
is possible to rename a net_device to a completely different name then the
original one.
It can therefore happen that a user registers a new batadv net_device with
the name "bat0". batman-adv is then also adding a new directory under
$debugfs/batman-adv/ with the name "wlan0".
The user then decides to rename this device to "bat1" and registers a
different batadv device with the name "bat0". batman-adv will then try to
create a directory with the name "bat0" under $debugfs/batman-adv/ again.
But there already exists one with this name under this path and thus this
fails. batman-adv will detect a problem and rollback the registering of
this device.
batman-adv must therefore take care of renaming the debugfs directories for
soft-interfaces whenever it detects such a net_device rename.
Fixes: c6c8fea297 ("net: Add batman-adv meshing protocol")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 36dc621cec ]
batman-adv is creating special debugfs directories in the init
net_namespace for each valid hard-interface (net_device). But it is
possible to rename a net_device to a completely different name then the
original one.
It can therefore happen that a user registers a new net_device which gets
the name "wlan0" assigned by default. batman-adv is also adding a new
directory under $debugfs/batman-adv/ with the name "wlan0".
The user then decides to rename this device to "wl_pri" and registers a
different device. The kernel may now decide to use the name "wlan0" again
for this new device. batman-adv will detect it as a valid net_device and
tries to create a directory with the name "wlan0" under
$debugfs/batman-adv/. But there already exists one with this name under
this path and thus this fails. batman-adv will detect a problem and
rollback the registering of this device.
batman-adv must therefore take care of renaming the debugfs directories
for hard-interfaces whenever it detects such a net_device rename.
Fixes: 5bc7c1eb44 ("batman-adv: add debugfs structure for information per interface")
Reported-by: John Soros <sorosj@gmail.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9713cb0cf1 ]
A reference for the best gateway is taken when the list of gateways in the
mesh is sent via netlink. This is necessary to check whether the currently
dumped entry is the currently selected gateway or not. This information is
then transferred as flag BATADV_ATTR_FLAG_BEST.
After the comparison of the current entry is done,
batadv_v_gw_dump_entry() has to decrease the reference counter again.
Otherwise the reference will be held and thus prevents a proper shutdown of
the batman-adv interfaces (and some of the interfaces enslaved in it).
Fixes: b71bb6f924 ("batman-adv: add B.A.T.M.A.N. V bat_gw_dump implementations")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b5685d2687 ]
A reference for the best gateway is taken when the list of gateways in the
mesh is sent via netlink. This is necessary to check whether the currently
dumped entry is the currently selected gateway or not. This information is
then transferred as flag BATADV_ATTR_FLAG_BEST.
After the comparison of the current entry is done,
batadv_iv_gw_dump_entry() has to decrease the reference counter again.
Otherwise the reference will be held and thus prevents a proper shutdown of
the batman-adv interfaces (and some of the interfaces enslaved in it).
Fixes: efb766af06 ("batman-adv: add B.A.T.M.A.N. IV bat_gw_dump implementations")
Reported-by: Andreas Ziegler <dev@andreas-ziegler.de>
Tested-by: Andreas Ziegler <dev@andreas-ziegler.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7b4e88434c ]
Smack: Mark inode instant in smack_task_to_inode
/proc clean-up in commit 1bbc55131e
resulted in smack_task_to_inode() being called before smack_d_instantiate.
This resulted in the smk_inode value being ignored, even while present
for files in /proc/self. Marking the inode as instant here fixes that.
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6c6da92808 ]
After recieving MLD querys, we update idev->mc_maxdelay with max_delay
from query header. This make the later unsolicited reports have the same
interval with mc_maxdelay, which means we may send unsolicited reports with
long interval time instead of default configured interval time.
Also as we will not call ipv6_mc_reset() after device up. This issue will
be there even after leave the group and join other groups.
Fixes: fc4eba58b4 ("ipv6: make unsolicited report intervals configurable for mld")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cbdceb9b3e ]
With gcc 4.1.2 when compiling for 32-bit:
drivers/mtd/devices/mtd_dataflash.c:736: warning: integer constant is too large for ‘long’ type
drivers/mtd/devices/mtd_dataflash.c:737: warning: integer constant is too large for ‘long’ type
Add the missing "ULL" suffixes to fix this.
Fixes: 67e4145ebf ("mtd: dataflash: Add flash_info for AT45DB641E")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 81e167c2a2 ]
The test_kmod.sh script require root privilege for the successful
execution of the test.
This patch is to notify the user about the privilege the script
demands for the successful execution of the test.
Signed-off-by: Jeffrin Jose T (Rajagiri SET) <ahiliation@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 12f8c553a5 ]
We had commit 06e226c7fb ("clk: sunxi-ng: Move all clock types to a
library") and commit 799c434154 ("kbuild: thin archives make default
for all archs") in the same development cycle, from different trees.
With migration to the thin archive, the entire drivers/clk/sunxi-ng/lib.a
is linked to the vmlinux. This does not break build, but we do not get
any size saving.
However, we do not need to go back to the individual Kconfig options.
The default configuration pulls in all (or most) of the CCU parts anyway.
Also, once we enable CONFIG_LD_DEAD_CODE_DATA_ELIMINATION, we can simply
list all files with obj-y, and the linker will drop all unused functions
by itself.
After the long discussion [1], people there agreed to fix this, but
nobody sent a patch after all. I am doing it now.
I lifted up CONFIG_SUNXI_CCU to drivers/clk/Makefile because everything
in drivers/clk/sunxi-ng/ depends on SUNXI_CCU.
[1] https://patchwork.kernel.org/patch/9796521/
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9f9cafc140 ]
There is race between nvme_remove and nvme_reset_work that can
lead to io hang.
nvme_remove nvme_reset_work
-> nvme_remove_dead_ctrl
-> nvme_dev_disable
-> quiesce request_queue
-> queue remove_work
-> cancel_work_sync reset_work
-> nvme_remove_namespaces
-> splice ctrl->namespaces
nvme_remove_dead_ctrl_work
-> nvme_kill_queues
-> nvme_ns_remove do nothing
-> blk_cleanup_queue
-> blk_freeze_queue
Finally, the request_queue is quiesced state when wait freeze,
we will get io hang here. To fix it, move the nvme_kill_queues
from nvme_remove_dead_ctrl_work to nvme_remove_dead_ctrl.
Suggested-by: Keith Busch <keith.busch@linux.intel.com>
Signed-off-by: Jianchao Wang <jianchao.w.wang@oracle.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ba56bc3a07 ]
When booting a 64 KB pages kernel on a ACPI GICv3 system that
implements support for v2 emulation, the following warning is
produced
GICV size 0x2000 not a multiple of page size 0x10000
and support for v2 emulation is disabled, preventing GICv2 VMs
from being able to run on such hosts.
The reason is that vgic_v3_probe() performs a sanity check on the
size of the window (it should be a multiple of the page size),
while the ACPI MADT parsing code hardcodes the size of the window
to 8 KB. This makes sense, considering that ACPI does not bother
to describe the size in the first place, under the assumption that
platforms implementing ACPI will follow the architecture and not
put anything else in the same 64 KB window.
So let's just drop the sanity check altogether, and assume that
the window is at least 64 KB in size.
Fixes: 9097773245 ("KVM: arm/arm64: vgic-new: vgic_init: implement kvm_vgic_hyp_init")
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fedb1bd3d2 ]
Currently it is incrementing SctpFragUsrMsgs when the user message size
is of the exactly same size as the maximum fragment size, which is wrong.
The fix is to increment it only when user message is bigger than the
maximum fragment size.
Fixes: bfd2e4b873 ("sctp: refactor sctp_datamsg_from_user")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ea0820bb77 ]
Device tree based systems without of_dev_auxdata will have the mdio
device named differently than "davinci_mdio(.0)". In this case use the
device's parent's compatible string for matching
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 08ba91ee6e ]
If NBD_DISCONNECT_ON_CLOSE is set on a device, then the driver will
issue a disconnect from nbd_release if the device has no remaining
bdev->bd_openers.
Fix ret val so reconfigure with only setting the flag succeeds.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Doron Roberts-Kedes <doronrk@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2f24ef7413 ]
machine_desc->init_per_cpu() hook is supposed to be per cpu
initialization and would seem to apply equally to UP and/or SMP.
Infact the comment in header file seems to suggest it works for
UP too, which was not the case and this patch.
This enables !CONFIG_SMP build for platforms such as hsdk.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
[vgupta: trimmeed changelog]
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d68a90e148 ]
Controllers that are not yet enabled should not really enforce keep alive
timeouts, but we still want to track a timeout and cleanup in case a host
died before it enabled the controller. Hence, simply reset the keep
alive timer when the controller is enabled.
Suggested-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c947657b15 ]
The race is between completing the request at error recovery work and
rdma completions. If we cancel the request before getting the good
rdma completion we get a NULL deref of the request MR at
nvme_rdma_process_nvme_rsp().
When Canceling the request we return its mr to the mr pool (set mr to
NULL) and also unmap its data. Canceling the requests while the rdma
queues are active is not safe. Because rdma queues are active and we
get good rdma completions that can use the mr pointer which may be NULL.
Completing the request too soon may lead also to performing DMA to/from
user buffers which might have been already unmapped.
The commit fixes the race by draining the QP before starting the abort
commands mechanism.
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3d0641015b ]
Failures after nvme_init_ctrl will defer resource cleanups to .free_ctrl
when the reference is released, hence we should not free the controller
queues for these failures.
Fix that by moving controller queues allocation before controller
initialization and correctly freeing them for failures before
initialization and skip them for failures after initialization.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bc8a2d9bcb ]
The Stratix10 platform has an additional reset line, OCP(Open Core Protocol),
that also needs to get deasserted for the stmmac ethernet controller to work.
Thus we need to update the Kconfig to include ARCH_STRATIX10 in order to build
dwmac-socfpga.
Also, remove the redundant check for the reset controller pointer. The
reset driver already checks for the pointer and returns 0 if the pointer
is NULL.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4e8439aa34 ]
The array bpq_eth_addr is only used to get the size of an
address, whereas the bcast_addr is used to set the broadcast
address. This leads to a warning when using clang:
drivers/net/hamradio/bpqether.c:94:13: warning: variable 'bpq_eth_addr' is not
needed and will not be emitted [-Wunneeded-internal-declaration]
static char bpq_eth_addr[6];
^
Remove both variables and use the common eth_broadcast_addr
to set the broadcast address.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3256d29fc7 ]
lockdep spotted that we are using rfs_h.lock in enic_get_rxnfc() without
initializing. rfs_h.lock is initialized in enic_open(). But ethtool_ops
can be called when interface is down.
Move enic_rfs_flw_tbl_init to enic_probe.
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 18 PID: 1189 Comm: ethtool Not tainted 4.17.0-rc7-devel+ #27
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.0-20171110_100015-anatol 04/01/2014
Call Trace:
dump_stack+0x85/0xc0
register_lock_class+0x550/0x560
? __handle_mm_fault+0xa8b/0x1100
__lock_acquire+0x81/0x670
lock_acquire+0xb9/0x1e0
? enic_get_rxnfc+0x139/0x2b0 [enic]
_raw_spin_lock_bh+0x38/0x80
? enic_get_rxnfc+0x139/0x2b0 [enic]
enic_get_rxnfc+0x139/0x2b0 [enic]
ethtool_get_rxnfc+0x8d/0x1c0
dev_ethtool+0x16c8/0x2400
? __mutex_lock+0x64d/0xa00
? dev_load+0x6a/0x150
dev_ioctl+0x253/0x4b0
sock_do_ioctl+0x9a/0x130
sock_ioctl+0x1af/0x350
do_vfs_ioctl+0x8e/0x670
? syscall_trace_enter+0x1e2/0x380
ksys_ioctl+0x60/0x90
__x64_sys_ioctl+0x16/0x20
do_syscall_64+0x5a/0x170
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ff54d5cd9e ]
Do not advertise DCBX_LLD_MANAGED capability i.e., do not allow
external agent to manage the dcbx/lldp negotiation. MFW acts as lldp agent
for qed* devices, and no other lldp agent is allowed to coexist with mfw.
Also updated a debug print, to not to display the redundant info.
Fixes: a1d8d8a51 ("qed: Add dcbnl support.")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4f9de4df90 ]
Memory for packet buffers need to be freed in the error paths as there is
no consumer (e.g., upper layer) for such packets and that memory will never
get freed.
The issue was uncovered when port was attacked with flood of isatap
packets, these are multicast packets hence were directed at all the PFs.
For foce PF, this meant they were routed to the ll2 module which in turn
drops such packets.
Fixes: 0a7fb11c ("qed: Add Light L2 support")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b154886f78 ]
We can't call function trace hook before setup percpu offset.
When entering secondary_start_kernel(), percpu offset has not
been initialized. So this lead hotplug malfunction.
Here is the flow to reproduce this bug:
echo 0 > /sys/devices/system/cpu/cpu1/online
echo function > /sys/kernel/debug/tracing/current_tracer
echo 1 > /sys/kernel/debug/tracing/tracing_on
echo 1 > /sys/devices/system/cpu/cpu1/online
Acked-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Zhizhou Zhang <zhizhouzhang@asrmicro.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dd65a941f6 ]
dma_alloc_*() buffers might be exposed to userspace via mmap() call, so
they should be cleared on allocation. In case of IOMMU-based dma-mapping
implementation such buffer clearing was missing in the code path for
DMA_ATTR_FORCE_CONTIGUOUS flag handling, because dma_alloc_from_contiguous()
doesn't honor __GFP_ZERO flag. This patch fixes this issue. For more
information on clearing buffers allocated by dma_alloc_* functions,
see commit 6829e274a6 ("arm64: dma-mapping: always clear allocated
buffers").
Fixes: 44176bb38f ("arm64: Add support for DMA_ATTR_FORCE_CONTIGUOUS to IOMMU")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2dbf8dffbf ]
Right now, we can call nfs_commit_inode() while holding the session slot,
which could lead to NFSv4 deadlocks. Ensure we only keep the slot if
the server returned a layout that we have to process.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit de6e5d3841 ]
Marking CPUs stopped by smp_send_stop as offline can cause warnings
due to cross-CPU wakeups. This trace was noticed on a busy system
running a sysrq+c crash test, after the injected crash:
WARNING: CPU: 51 PID: 1546 at kernel/sched/core.c:1179 set_task_cpu+0x22c/0x240
CPU: 51 PID: 1546 Comm: kworker/u352:1 Tainted: G D
Workqueue: mlx5e mlx5e_update_stats_work [mlx5_core]
[...]
NIP [c00000000017c21c] set_task_cpu+0x22c/0x240
LR [c00000000017d580] try_to_wake_up+0x230/0x720
Call Trace:
[c000000001017700] runqueues+0x0/0xb00 (unreliable)
[c00000000017d580] try_to_wake_up+0x230/0x720
[c00000000015a214] insert_work+0x104/0x140
[c00000000015adb0] __queue_work+0x230/0x690
[c000003fc5007910] [c00000000015b26c] queue_work_on+0x5c/0x90
[c0080000135fc8f8] mlx5_cmd_exec+0x538/0xcb0 [mlx5_core]
[c008000013608fd0] mlx5_core_access_reg+0x140/0x1d0 [mlx5_core]
[c00800001362777c] mlx5e_update_pport_counters.constprop.59+0x6c/0x90 [mlx5_core]
[c008000013628868] mlx5e_update_ndo_stats+0x28/0x90 [mlx5_core]
[c008000013625558] mlx5e_update_stats_work+0x68/0xb0 [mlx5_core]
[c00000000015bcec] process_one_work+0x1bc/0x5f0
[c00000000015ecac] worker_thread+0xac/0x6b0
[c000000000168338] kthread+0x168/0x1b0
[c00000000000b628] ret_from_kernel_thread+0x5c/0xb4
This happens because firstly the CPU is not really offline in the
usual sense, processes and interrupts have not been migrated away.
Secondly smp_send_stop does not happen atomically on all CPUs, so
one CPU can have marked itself offline, while another CPU is still
running processes or interrupts which can affect the first CPU.
Fix this by just not marking the CPU as offline. It's more like
frozen in time, so offline does not really reflect its state properly
anyway. There should be nothing in the crash/panic path that walks
online CPUs and synchronously waits for them, so this change should
not introduce new hangs.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 70c3c8cb83 ]
If isoc split in transfer with no data (the length of DATA0
packet is zero), we can't simply return immediately. Because
the DATA0 can be the first transaction or the second transaction
for the isoc split in transaction. If the DATA0 packet with no
data is in the first transaction, we can return immediately.
But if the DATA0 packet with no data is in the second transaction
of isoc split in transaction sequence, we need to increase the
qtd->isoc_frame_index and giveback urb to device driver if needed,
otherwise, the MDATA packet will be lost.
A typical test case is that connect the dwc2 controller with an
usb hs Hub (GL852G-12), and plug an usb fs audio device (Plantronics
headset) into the downstream port of Hub. Then use the usb mic
to record, we can find noise when playback.
In the case, the isoc split in transaction sequence like this:
- SSPLIT IN transaction
- CSPLIT IN transaction
- MDATA packet (176 bytes)
- CSPLIT IN transaction
- DATA0 packet (0 byte)
This patch use both the length of DATA0 and qtd->isoc_split_offset
to check if the DATA0 is in the second transaction.
Tested-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Minas Harutyunyan hminas@synopsys.com>
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit af424a4107 ]
The commit 3bc04e28a0 ("usb: dwc2: host: Get aligned DMA in
a more supported way") rips out a lot of code to simply the
allocation of aligned DMA. However, it also introduces a new
issue when use isoc split in transfer.
In my test case, I connect the dwc2 controller with an usb hs
Hub (GL852G-12), and plug an usb fs audio device (Plantronics
headset) into the downstream port of Hub. Then use the usb mic
to record, we can find noise when playback.
It's because that the usb Hub uses an MDATA for the first
transaction and a DATA0 for the second transaction for the isoc
split in transaction. An typical isoc split in transaction sequence
like this:
- SSPLIT IN transaction
- CSPLIT IN transaction
- MDATA packet
- CSPLIT IN transaction
- DATA0 packet
The DMA address of MDATA (urb->dma) is always DWORD-aligned, but
the DMA address of DATA0 (urb->dma + qtd->isoc_split_offset) may
not be DWORD-aligned, it depends on the qtd->isoc_split_offset (the
length of MDATA). In my test case, the length of MDATA is usually
unaligned, this cause DATA0 packet transmission error.
This patch use kmem_cache to allocate aligned DMA buf for isoc
split in transaction. Note that according to usb 2.0 spec, the
maximum data payload size is 1023 bytes for each fs isoc ep,
and the maximum allowable interrupt data payload size is 64 bytes
or less for fs interrupt ep. So we set the size of object to be
1024 bytes in the kmem cache.
Tested-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Minas Harutyunyan hminas@synopsys.com>
Signed-off-by: William Wu <william.wu@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 22bb5cfdf1 ]
In case when a hub is connected to DWC2 host
auto suspend occurs and host goes to
hibernation. When any device connected to hub
host hibernation exiting incorrectly.
- Added dwc2_hcd_rem_wakeup() function call to
exit from suspend state by remote wakeup.
- Increase timeout value for port suspend bit to be set.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c9bd0946da ]
Commit 0198d7bb8a ("ASoC: omap-mcbsp: Convert to use the sdma-pcm
instead of omap-pcm") resulted in broken audio playback on OMAP1510
(discovered on Amstrad Delta).
When running on OMAP1510, omap-pcm used to obtain DMA offset from
snd_dmaengine_pcm_pointer_no_residue() based on DMA interrupt triggered
software calculations instead of snd_dmaengine_pcm_pointer() which
depended on residue value calculated from omap_dma_get_src_pos().
Similar code path is still available in now used
sound/soc/soc-generic-dmaengine-pcm.c but it is not triggered.
It was verified already before that omap_get_dma_src_pos() from
arch/arm/plat-omap/dma.c didn't work correctly for OMAP1510 - see
commit 1bdd741991 ("ASoC: OMAP: fix OMAP1510 broken PCM pointer
callback") for details. Apparently the same applies to its successor,
omap_dma_get_src_pos() from drivers/dma/ti/omap-dma.c.
On the other hand, snd_dmaengine_pcm_pointer_no_residue() is described
as depreciated and discouraged for use in new drivers because of its
unreliable accuracy. However, it seems the only working option for
OPAM1510 now, as long as a software calculated residue is not
implemented as OMAP1510 fallback in omap-dma.
Using snd_dmaengine_pcm_pointer_no_residue() code path instead of
snd_dmaengine_pcm_pointer() in sound/soc/soc-generic-dmaengine-pcm.c
can be triggered in two ways:
- by passing pcm->flags |= SND_DMAENGINE_PCM_FLAG_NO_RESIDUE from
sound/soc/omap/sdma-pcm.c,
- by passing dma_caps.residue_granularity =
DMA_RESIDUE_GRANULARITY_DESCRIPTOR from DMA engine.
Let's do the latter.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fae2a63737 ]
Currently smatch warns of possible Spectre-V1 issue in ahci_led_store():
drivers/ata/libahci.c:1150 ahci_led_store() warn: potential spectre issue 'pp->em_priv' (local cap)
Userspace controls @pmp from following callchain:
em_message->store()
->ata_scsi_em_message_store()
-->ap->ops->em_store()
--->ahci_led_store()
After the mask+shift @pmp is effectively an 8b value, which is used to
index into an array of length 8, so sanitize the array index.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 375dc53d03 ]
Run the completer task to post a work completion after processing
a memory registration or invalidate work request. This covers the
case where the memory registration or invalidate was the last work
request posted to the qp.
Signed-off-by: Vijay Immanuel <vijayi@attalasystems.com>
Reviewed-by: Yonatan Cohen <yonatanc@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 89610dc2c2 ]
In the situation that DE and SE aren’t shared the same interrupt number,
the Global SE interrupts mask bit MASK_IRQ_EN in MASKIRQ must be set, or
else other mask bits will not work and no SE interrupt will occur. This
patch enables MASK_IRQ_EN for SE to fix this problem.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 109c4d18e5 ]
One needs to ensure that the crtcs are shutdown so that the
drm_crtc_state->connector_mask reflects that no connectors
are currently active. Further, it reduces the reference
count for each connector. This ensures that the connectors
and encoders can be cleanly removed either when _unbind
is called for the corresponding drivers or by
drm_mode_config_cleanup().
We need drm_atomic_helper_shutdown() to be called before
component_unbind_all() otherwise the connectors attached to the
component device will have the wrong reference count value and will not
be cleanly removed.
Signed-off-by: Ayan Kumar Halder <ayan.halder@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a45fc268db ]
This patch fixes the below parser error of the IOB SLOW PMU.
# perf stat -a -e iob-slow0/cycle-count/ sleep 1
evenf syntax error: 'iob-slow0/cycle-count/'
\___ parser error
It replaces the "-" character by "_" character inside the PMU name.
Signed-off-by: Hoan Tran <hoan.tran@amperecomputing.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dbe4a39331 ]
The i2c and PCIe controllers had an incorrect type which should have
been set to IRQ_TYPE_LEVEL_HIGH, fix that.
Fixes: b9099ec754 ("ARM: dts: Add Broadcom Hurricane 2 DTS include file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 403fde6448 ]
The interrupts for the PCIe controllers should all be of type
IRQ_TYPE_LEVEL_HIGH instead of IRQ_TYPE_NONE.
Fixes: d71eb94120 ("ARM: dts: NSP: Add MSI support on PCI")
Fixes: 522199029f ("ARM: dts: NSP: Fix PCIE DT issue")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d6a3e55131 ]
Unless the software synchronization objects (CONFIG_SW_SYNC) is enabled,
the sync test will be skipped:
TAP version 13
1..0 # Skipped: Sync framework not supported by kernel
Add a config fragment file to be able to run "make kselftest-merge" to
enable relevant configuration required in order to run the sync test.
Signed-off-by: Fathi Boudra <fathi.boudra@linaro.org>
Link: https://lkml.org/lkml/2017/5/5/14
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a4d7537789 ]
When vm test is skipped because of unmet dependencies and/or unsupported
configuration, it exits with error which is treated as a fail by the
Kselftest framework. This leads to false negative result even when the
test could not be run.
Change it to return kselftest skip code when a test gets skipped to
clearly report that the test could not be run.
Kselftest framework SKIP code is 4 and the framework prints appropriate
messages to indicate that the test is skipped.
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Acked-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 685814466b ]
When zram test is skipped because of unmet dependencies and/or
unsupported configuration, it exits with error which is treated as
a fail by the Kselftest framework. This leads to false negative result
even when the test could not be run.
Change it to return kselftest skip code when a test gets skipped to
clearly report that the test could not be run.
Kselftest framework SKIP code is 4 and the framework prints appropriate
messages to indicate that the test is skipped.
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d7d5311d4a ]
When user test is skipped because of unmet dependencies and/or
unsupported configuration, it exits with error which is treated as
a fail by the Kselftest framework. This leads to false negative result
even when the test could not be run.
Change it to return kselftest skip code when a test gets skipped to
clearly report that the test could not be run. Add an explicit check
for module presence and return skip code if module isn't present.
Kselftest framework SKIP code is 4 and the framework prints appropriate
messages to indicate that the test is skipped.
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c7db6ffb83 ]
When sysctl test is skipped because of unmet dependencies and/or
unsupported configuration, it exits with error which is treated as
a fail by the Kselftest framework. This leads to false negative result
even when the test could not be run.
Change it to return kselftest skip code when a test gets skipped to
clearly report that the test could not be run.
Changed return code to kselftest skip code in skip error legs that check
requirements and module probe test error leg.
Kselftest framework SKIP code is 4 and the framework prints appropriate
messages to indicate that the test is skipped.
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8781578087 ]
When static_keys test is skipped because of unmet dependencies and/or
unsupported configuration, it exits with error which is treated as a fail
by the Kselftest framework. This leads to false negative result even when
the test could not be run.
Change it to return kselftest skip code when a test gets skipped to clearly
report that the test could not be run.
Added an explicit searches for test_static_key_base and test_static_keys
modules and return skip code if they aren't found to differentiate between
the failure to load the module condition and module not found condition.
Kselftest framework SKIP code is 4 and the framework prints appropriate
messages to indicate that the test is skipped.
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 856e7c4b61 ]
When pstore_post_reboot test gets skipped because of unmet dependencies
and/or unsupported configuration, it returns 0 which is treated as a pass
by the Kselftest framework. This leads to false positive result even when
the test could not be run.
Change it to return kselftest skip code when a test gets skipped to clearly
report that the test could not be run.
Kselftest framework SKIP code is 4 and the framework prints appropriate
messages to indicate that the test is skipped.
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ad9852af97 ]
The helper module would be unloaded after nf_conntrack_helper_unregister,
so it may cause a possible panic caused by race.
nf_ct_iterate_destroy(unhelp, me) reset the helper of conntrack as NULL,
but maybe someone has gotten the helper pointer during this period. Then
it would panic, when it accesses the helper and the module was unloaded.
Take an example as following:
CPU0 CPU1
ctnetlink_dump_helpinfo
helper = rcu_dereference(help->helper);
unhelp
set helper as NULL
unload helper module
helper->to_nlattr(skb, ct);
As above, the cpu0 tries to access the helper and its module is unloaded,
then the panic happens.
Signed-off-by: Gao Feng <gfree.wind@vip.163.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9ce7bc036a ]
It is a waste of memory to use a full "struct netns_sysctl_ipv6"
while only one pointer is really used, considering netns_sysctl_ipv6
keeps growing.
Also, since "struct netns_frags" has cache line alignment,
it is better to move the frags_hdr pointer outside, otherwise
we spend a full cache line for this pointer.
This saves 192 bytes of memory per netns.
Fixes: c038a767cd ("ipv6: add a new namespace for nf_conntrack_reasm")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8195a655e5 ]
On this system EC interrupt triggers constantly kicking devices out of
low power states and thus blocking power management. The system also has
a PCIe root port hosting Alpine Ridge Thunderbolt controller and it
never gets a chance to go to D3cold because of this.
Since the power button works the same regardless if EC interrupt is
enabled or not during s2idle, add a quirk for this machine that sets
ec_no_wakeup=true preventing spurious wakeups.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 896e518883 ]
The clocks have already been explicitly disabled and put as part of
remove() so the runtime suspend callback must not be run when balancing
the runtime PM usage count before returning.
Fixes: 16adc674d0 ("usb: dwc3: add generic OF glue layer")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3637f12faf ]
Correct MIPI/PCIe/USB_HSIC's PGC offset based on
design RTL, the values in the Reference Manual
(Rev. 1, 01/2018 and the older ones) are incorrect.
The correct offset values should be as below:
0x800 ~ 0x83F: PGC for core0 of A7 platform;
0x840 ~ 0x87F: PGC for core1 of A7 platform;
0x880 ~ 0x8BF: PGC for SCU of A7 platform;
0xA00 ~ 0xA3F: PGC for fastmix/megamix;
0xC00 ~ 0xC3F: PGC for MIPI PHY;
0xC40 ~ 0xC7F: PGC for PCIe_PHY;
0xC80 ~ 0xCBF: PGC for USB OTG1 PHY;
0xCC0 ~ 0xCFF: PGC for USB OTG2 PHY;
0xD00 ~ 0xD3F: PGC for USB HSIC PHY;
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Fixes: 03aa12629f ("soc: imx: Add GPCv2 power gating driver")
Acked-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 91bb8f45f7 ]
Commit cc66b30382 ("hwmon: (nct6775) Rework temperature source and label
handling") changed a loop limit from "data->temp_label_num - 1" to "32",
as part of moving from a string array to a bit mask. This results in the
following error, reported by UBSAN.
UBSAN: Undefined behaviour in drivers/hwmon/nct6775.c:4179:27
shift exponent 32 is too large for 32-bit type 'long unsigned int'
Similar to the original loop, the limit has to be one less than the
number of bits.
Fixes: cc66b30382 ("hwmon: (nct6775) Rework temperature source and label handling")
Reported-by: Paul Menzel <pmenzel+linux-hwmon@molgen.mpg.de>
Cc: Paul Menzel <pmenzel+linux-hwmon@molgen.mpg.de>
Tested-by: Paul Menzel <pmenzel+linux-hwmon@molgen.mpg.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d409014e4f ]
Compared to other clients the Linux smb3 client ramps up
credits very slowly, taking more than 128 operations before a
maximum size write could be sent (since the number of credits
requested is only 2 per small operation, causing the credit
limit to grow very slowly).
This lack of credits initially would impact large i/o performance,
when large i/o is tried early before enough credits are built up.
Signed-off-by: Steve French <sfrench@gmail.com>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 47cf52a246 ]
Modern distroes increasingly make use of BPF programs. Default
Ubuntu 18.04 installation boots with a number of cgroup_skb
programs loaded.
test_offloads.py tries to check if programs and maps are not
leaked on error paths by confirming the list of programs on the
system is empty between tests.
Since we can no longer expect the system to have no BPF objects
at boot try to remember the programs and maps present at the start,
and skip those when scanning the system.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 74c11e300c ]
GCC built for arc*-*-linux has "-mmedium-calls" implicitly enabled by default
thus we don't see any problems during Linux kernel compilation.
----------------------------->8------------------------
arc-linux-gcc -mcpu=arc700 -Q --help=target | grep calls
-mlong-calls [disabled]
-mmedium-calls [enabled]
----------------------------->8------------------------
But if we try to use so-called Elf32 toolchain with GCC configured for
arc*-*-elf* then we'd see the following failure:
----------------------------->8------------------------
init/do_mounts.o: In function 'init_rootfs':
do_mounts.c:(.init.text+0x108): relocation truncated to fit: R_ARC_S21W_PCREL
against symbol 'unregister_filesystem' defined in .text section in fs/filesystems.o
arc-elf32-ld: final link failed: Symbol needs debug section which does not exist
make: *** [vmlinux] Error 1
----------------------------->8------------------------
That happens because neither "-mmedium-calls" nor "-mlong-calls" are enabled in
Elf32 GCC:
----------------------------->8------------------------
arc-elf32-gcc -mcpu=arc700 -Q --help=target | grep calls
-mlong-calls [disabled]
-mmedium-calls [disabled]
----------------------------->8------------------------
Now to make it possible to use Elf32 toolchain for building Linux kernel
we're explicitly add "-mmedium-calls" to CFLAGS.
And since we add "-mmedium-calls" to the global CFLAGS there's no point in
having per-file copies thus removing them.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3dc7c7badb ]
Before returning -EPERM we should release some resources, as already done
in the other error handling path of the function.
Fixes: d8f9cc328c ("IB/mlx4: Mark user MR as writable if actual virtual memory is writable")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 645a397d32 ]
The documentation for the touchscreen-swapped-x-y property states that
swapping is done after inverting if both are used. RMI4 did it the other
way around, leading to inconsistent behavior with regard to other
touchscreens.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 425cf5c135 ]
Some RoCE specific code in qedr_modify_qp was run over an iWARP device
when running perftest benchmarks without the -R option.
The commit 3e44e0ee08 ("IB/providers: Avoid null netdev check for RoCE")
exposed this. Dropping the check for NULL pointer on ndev in
qedr_modify_qp lead to a null pointer dereference when running over
iWARP. Before the code would identify ndev as being NULL and return an
error.
Fixes: 3e44e0ee08 ("IB/providers: Avoid null netdev check for RoCE")
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 828d810550 ]
In rxe_send, when network_type is not RDMA_NETWORK_IPV4 or
RDMA_NETWORK_IPV6, skb is freed and -EINVAL is returned.
Then rxe_xmit_packet will return -EINVAL, too. In rxe_requester,
this skb is double freed.
In rxe_requester, kfree_skb is needed only after fill_packet fails.
So kfree_skb is moved from label err to test fill_packet.
Fixes: 5793b46521 ("IB/rxe: remove unnecessary skb_clone in xmit")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0f5c6c30a0 ]
The mvneta Ethernet driver is used on a few different Marvell SoCs.
Some SoCs have per cpu interrupts for Ethernet events, the driver uses
a per CPU napi structure for this case. Some SoCs such as armada 3700
have a single interrupt for Ethernet events, the driver uses a global
napi structure for this case.
Current mvneta_config_rss() always operates the per cpu napi structure.
Fix it by operating a global napi for "single interrupt" case, and per
cpu napi structure for remaining cases.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Fixes: 2636ac3cc2 ("net: mvneta: Add network support for Armada 3700 SoC")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7a86f05faf ]
The mvneta Ethernet driver is used on a few different Marvell SoCs.
Some SoCs have per cpu interrupts for Ethernet events. Some SoCs have
a single interrupt, independent of the CPU. The driver handles this by
having a per CPU napi structure when there are per CPU interrupts, and
a global napi structure when there is a single interrupt.
When the napi core calls mvneta_poll(), it passes the napi
instance. This was not being propagated through the call chain, and
instead the per-cpu napi instance was passed to napi_gro_receive()
call. This breaks when there is a single global napi instance.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 2636ac3cc2 ("net: mvneta: Add network support for Armada 3700 SoC")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7bb05b85bc ]
Found the ethernet network on ASUS X441UAR doesn't come back on resume
from suspend when using MSI-X. The chip is RTL8106e - version 39.
[ 21.848357] libphy: r8169: probed
[ 21.848473] r8169 0000:02:00.0 eth0: RTL8106e, 0c:9d:92:32:67:b4, XID
44900000, IRQ 127
[ 22.518860] r8169 0000:02:00.0 enp2s0: renamed from eth0
[ 29.458041] Generic PHY r8169-200:00: attached PHY driver [Generic
PHY] (mii_bus:phy_addr=r8169-200:00, irq=IGNORE)
[ 63.227398] r8169 0000:02:00.0 enp2s0: Link is Up - 100Mbps/Full -
flow control off
[ 124.514648] Generic PHY r8169-200:00: attached PHY driver [Generic
PHY] (mii_bus:phy_addr=r8169-200:00, irq=IGNORE)
Here is the ethernet controller in detail:
02:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd.
RTL8101/2/6E PCI Express Fast/Gigabit Ethernet controller [10ec:8136]
(rev 07)
Subsystem: ASUSTeK Computer Inc. RTL810xE PCI Express Fast
Ethernet controller [1043:200f]
Flags: bus master, fast devsel, latency 0, IRQ 16
I/O ports at e000 [size=256]
Memory at ef100000 (64-bit, non-prefetchable) [size=4K]
Memory at e0000000 (64-bit, prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: r8169
Kernel modules: r8169
Falling back to MSI fixes the issue.
Fixes: 6c6aa15fde ("r8169: improve interrupt handling")
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5e22002aa8 ]
It was possible to directly leak the kernel address where the isdn_dev
structure pointer was stored. This is a kernel ASLR bypass for anyone
with access to the ioctl. The code had been present since the beginning
of git history, though this shouldn't ever be needed for normal operation,
therefore remove it.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Karsten Keil <isdn@linux-pingi.de>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f294d00961 upstream.
Make sure to disable clocks and deregister any exported partitions
before returning on late probe errors.
Note that since commit ee895ccdf7 ("misc: sram: fix enabled clock leak
on error path"), partitions are deliberately exported before enabling
the clock so we stick to that logic here. A follow up patch will address
this.
Cc: stable <stable@vger.kernel.org> # 4.9
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dfcab6ba57 upstream.
dw8250_set_termios() doesn't set baud rate if the arg "old ktermios" is
NULL. This happens during resume.
Call Trace:
...
[ 54.928108] dw8250_set_termios+0x162/0x170
[ 54.928114] serial8250_set_termios+0x17/0x20
[ 54.928117] uart_change_speed+0x64/0x160
[ 54.928119] uart_resume_port
...
So the baud rate is not restored after S3 and breaks the apps who use
UART, for example, console and bluetooth etc.
We address this issue by setting the baud rate irrespective of arg
"old", just like the drivers for other 8250 IPs. This is tested with
Intel Broxton platform.
Signed-off-by: Chen Hu <hu1.chen@intel.com>
Fixes: 4e26b134bd ("serial: 8250_dw: clock rate handling for all ACPI platforms")
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 60ab0fafc4 upstream.
The sleep wake-up refactoring that I introduced in
commit c7e1b40590 ("tty: serial: exar: Relocate sleep wake-up handling")
did not account for devices with a slave device on the expansion port.
This patch pokes the INT0 register in the slave device, if present, in
order to ensure that MSI interrupts don't get permanently "stuck"
because of a sleep wake-up interrupt as described here:
commit 2c0ac5b48a ("serial: exar: Fix stuck MSIs")
This also converts an ioread8() to readb() in order to provide visual
consistency with the MMIO-only accessors used elsewhere in the driver.
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Fixes: c7e1b40590 ("tty: serial: exar: Relocate sleep wake-up handling")
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 47ac76662c upstream.
Revert commit ecb988a3b7: tty: serial:
8250: 8250_core: NXP SC16C2552 workaround
The above commit causes userland application to no longer write
correctly its first write to a dumb terminal connected to /dev/ttyS0.
This commit seems to be the culprit. It's as though the TX FIFO is being
reset during that write. What should be displayed is:
PSW 80000000 INST 00000000 HALT
//
What is displayed is some variation of:
T 00000000 HAL//
Reverting this commit via this patch fixes my problem.
Signed-off-by: Mark Hounschell <dmarkh@cfl.rr.com>
Fixes: ecb988a3b7 ("tty: serial: 8250: 8250_core: NXP SC16C2552 workaround")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 231f941500 upstream.
Every time I tried to upgrade my laptop from 3.10.x to 4.x I faced an
issue by which the fan would run at full speed upon resume. Bisecting
it showed me the issue was introduced in 3.17 by commit 821d6f0359
(ACPI / sleep: Do not save NVS for new machines to accelerate S3). This
code only affects machines built starting as of 2012, but this Asus
1025C laptop was made in 2012 and apparently needs the NVS data to be
saved, otherwise the CPU's thermal state is not properly reported on
resume and the fan runs at full speed upon resume.
Here's a very simple way to check if such a machine is affected :
# cat /sys/class/thermal/thermal_zone0/temp
55000
( now suspend, wait one second and resume )
# cat /sys/class/thermal/thermal_zone0/temp
0
(and after ~15 seconds the fan starts to spin)
Let's apply the same quirk as commit cbc00c13 (ACPI: save NVS memory
for Lenovo G50-45) and reuse the function it provides. Note that this
commit was already backported to 4.9.x but not 4.4.x.
Cc: 3.17+ <stable@vger.kernel.org> # 3.17+: requires cbc00c13
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e60870012e upstream.
The portdata spinlock can be taken in interrupt context (via
sierra_outdat_callback()).
Disable interrupts when taking the portdata spinlock when discarding
deferred URBs during close to prevent a possible deadlock.
Fixes: 014333f77c ("USB: sierra: fix urb and memory leak on disconnect")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
[ johan: amend commit message and add fixes and stable tags ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a49a71f6e2 upstream.
The sanity checks in ALSA sequencer and OSS sequencer emulation codes
return falsely -ENXIO from poll callback. They should be EPOLLERR
instead.
This was caught thanks to the recent change to the return value.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3acd3e3bab upstream.
The endian conversions used in vxp_dma_read() and vxp_dma_write() are
superfluous and even wrong on big-endian machines, as inw() and outw()
already do conversions. Kill them.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dfef01e150 upstream.
snd_dma_alloc_pages_fallback() tries to allocate pages again when the
allocation fails with reduced size. But the first try actually
*increases* the size to power-of-two, which may give back a larger
chunk than the requested size. This confuses the callers, e.g. sgbuf
assumes that the size is equal or less, and it may result in a bad
loop due to the underflow and eventually lead to Oops.
The code of this function seems incorrectly assuming the usage of
get_order(). We need to decrease at first, then align to
power-of-two.
Reported-and-tested-by: he, bo <bo.he@intel.com>
Reported-by: zhang jun <jun.zhang@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 69756930f2 upstream.
One place in cs5535audio_build_dma_packets() does an extra conversion
via cpu_to_le32(); namely jmpprd_addr is passed to setup_prd() ops,
which writes the value via cs_writel(). That is, the callback does
the conversion by itself, and we don't need to convert beforehand.
This patch fixes that bogus conversion.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 50e9ffb199 upstream.
The virmidi output trigger tries to parse the all available bytes and
process sequencer events as much as possible. In a normal situation,
this is supposed to be relatively short, but a program may give a huge
buffer and it'll take a long time in a single spin lock, which may
eventually lead to a soft lockup.
This patch simply adds a workaround, a cond_resched() call in the loop
if applicable. A better solution would be to move the event processor
into a work, but let's put a duct-tape quickly at first.
Reported-and-tested-by: Dae R. Jeong <threeearcat@gmail.com>
Reported-by: syzbot+619d9f40141d826b097e@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fff71a4c05 upstream.
The endian conversions used in vx2_dma_read() and vx2_dma_write() are
superfluous and even wrong on big-endian machines, as inl() and outl()
already do conversions. Kill them.
Spotted by sparse, a warning like:
sound/pci/vx222/vx222_ops.c:278:30: warning: incorrect type in argument 1 (different base types)
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d77a4b4a5b upstream.
As an equivalent codec with CX20724,
CX8200 is also subject to the reboot bug.
Late 2017 and 2018 LG Gram and some HP Spectre laptops are known victims
to this issue, causing extremely loud noises upon reboot.
Now that we know that this bug is subject to multiple codecs,
fix the comment as well.
Signed-off-by: Park Ju Hyung <qkrwngud825@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f59cf9a055 upstream.
On rare occasions, we are still noticing that the internal speaker
spitting out spurious noises even after adding the problematic codec
to the list.
Adding a 10ms artificial delay before rebooting fixes the issue entirely.
Patch for Realtek codecs also adds the same amount of delay after
entering D3.
Signed-off-by: Park Ju Hyung <qkrwngud825@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 330bdcfadc ]
AF_RXRPC has a keepalive message generator that generates a message for a
peer ~20s after the last transmission to that peer to keep firewall ports
open. The implementation is incorrect in the following ways:
(1) It mixes up ktime_t and time64_t types.
(2) It uses ktime_get_real(), the output of which may jump forward or
backward due to adjustments to the time of day.
(3) If the current time jumps forward too much or jumps backwards, the
generator function will crank the base of the time ring round one slot
at a time (ie. a 1s period) until it catches up, spewing out VERSION
packets as it goes.
Fix the problem by:
(1) Only using time64_t. There's no need for sub-second resolution.
(2) Use ktime_get_seconds() rather than ktime_get_real() so that time
isn't perceived to go backwards.
(3) Simplifying rxrpc_peer_keepalive_worker() by splitting it into two
parts:
(a) The "worker" function that manages the buckets and the timer.
(b) The "dispatch" function that takes the pending peers and
potentially transmits a keepalive packet before putting them back
in the ring into the slot appropriate to the revised last-Tx time.
(4) Taking everything that's pending out of the ring and splicing it into
a temporary collector list for processing.
In the case that there's been a significant jump forward, the ring
gets entirely emptied and then the time base can be warped forward
before the peers are processed.
The warping can't happen if the ring isn't empty because the slot a
peer is in is keepalive-time dependent, relative to the base time.
(5) Limit the number of iterations of the bucket array when scanning it.
(6) Set the timer to skip any empty slots as there's no point waking up if
there's nothing to do yet.
This can be triggered by an incoming call from a server after a reboot with
AF_RXRPC and AFS built into the kernel causing a peer record to be set up
before userspace is started. The system clock is then adjusted by
userspace, thereby potentially causing the keepalive generator to have a
meltdown - which leads to a message like:
watchdog: BUG: soft lockup - CPU#0 stuck for 23s! [kworker/0:1:23]
...
Workqueue: krxrpcd rxrpc_peer_keepalive_worker
EIP: lock_acquire+0x69/0x80
...
Call Trace:
? rxrpc_peer_keepalive_worker+0x5e/0x350
? _raw_spin_lock_bh+0x29/0x60
? rxrpc_peer_keepalive_worker+0x5e/0x350
? rxrpc_peer_keepalive_worker+0x5e/0x350
? __lock_acquire+0x3d3/0x870
? process_one_work+0x110/0x340
? process_one_work+0x166/0x340
? process_one_work+0x110/0x340
? worker_thread+0x39/0x3c0
? kthread+0xdb/0x110
? cancel_delayed_work+0x90/0x90
? kthread_stop+0x70/0x70
? ret_from_fork+0x19/0x24
Fixes: ace45bec6d ("rxrpc: Fix firewall route keepalive")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7c53a72245 ]
There have been two reports that network doesn't come back on resume
from suspend when using MSI-X. Both cases affect the same chip version
(RTL8168g - version 40), on different systems. Falling back to MSI
fixes the issue.
Even though we don't really have a proof yet that the network chip
version is to blame, let's disable MSI-X for this version.
Reported-by: Steve Dodd <steved424@gmail.com>
Reported-by: Lou Reed <gogen@disroot.org>
Tested-by: Steve Dodd <steved424@gmail.com>
Tested-by: Lou Reed <gogen@disroot.org>
Fixes: 6c6aa15fde ("r8169: improve interrupt handling")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 816f670623 ]
The current check relies on function BDF addresses and can get
us wrong e.g when two VFs are assigned into a VM and the PCI
v-address is set by the hypervisor.
Fixes: 5c65c564c9 ('net/mlx5e: Support offloading TC NIC hairpin flows')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Alaa Hleihel <alaa@mellanox.com>
Tested-by: Alaa Hleihel <alaa@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit caebd1b389 ]
In previous patch mlxsw_afa_resource_del() was added to avoid a duplicate
resource detruction scenario.
For mirror actions, such duplicate destruction leads to a crash as in:
# tc qdisc add dev swp49 ingress
# tc filter add dev swp49 parent ffff: \
protocol ip chain 100 pref 10 \
flower skip_sw dst_ip 192.168.101.1 action drop
# tc filter add dev swp49 parent ffff: \
protocol ip pref 10 \
flower skip_sw dst_ip 192.168.101.1 action goto chain 100 \
action mirred egress mirror dev swp4
Therefore add a call to mlxsw_afa_resource_del() in
mlxsw_afa_mirror_destroy() in order to clear that resource
from rule's resources.
Fixes: d0d13c1858 ("mlxsw: spectrum_acl: Add support for mirror action")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7cc6169493 ]
Each tc flower rule uses a hidden count action. As counter resource may
not be available due to limited HW resources, update _counter_create()
and _counter_destroy() pair to follow previously introduced symmetric
error condition handling, add a call to mlxsw_afa_resource_del() as part
of the counter resource destruction.
Fixes: c18c1e186b ("mlxsw: core: Make counter index allocated inside the action append")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dda0a3a3fb ]
Some ACL actions require the allocation of a separate resource
prior to applying the action itself. When facing an error condition
during the setup phase of the action, resource should be destroyed.
For such actions the destruction was done twice which is dangerous
and lead to a potential crash.
The destruction took place first upon error on action setup phase
and then as the rule was destroyed.
The following sequence generated a crash:
# tc qdisc add dev swp49 ingress
# tc filter add dev swp49 parent ffff: \
protocol ip chain 100 pref 10 \
flower skip_sw dst_ip 192.168.101.1 action drop
# tc filter add dev swp49 parent ffff: \
protocol ip pref 10 \
flower skip_sw dst_ip 192.168.101.1 action goto chain 100 \
action mirred egress mirror dev swp4
Therefore add mlxsw_afa_resource_del() as a complement of
mlxsw_afa_resource_add() to add symmetry to resource_list membership
handling. Call this from mlxsw_afa_fwd_entry_ref_destroy() to make the
_fwd_entry_ref_create() and _fwd_entry_ref_destroy() pair of calls a
NOP.
Fixes: 140ce42121 ("mlxsw: core: Convert fwd_entry_ref list to be generic per-block resource list")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 82a40777de ]
According to RFC791, 68 bytes is the minimum size of IPv4 datagram every
device must be able to forward without further fragmentation while 576
bytes is the minimum size of IPv4 datagram every device has to be able
to receive, so in ip6_tnl_xmit(), 68(IPV4_MIN_MTU) should be the right
value for the ipv4 min mtu check in ip6_tnl_xmit.
While at it, change to use max() instead of if statement.
Fixes: c9fefa0819 ("ip6_tunnel: get the min mtu properly in ip6_tnl_xmit")
Reported-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 11ba961c91 ]
It was noticed that NIC always pass all multicast traffic to the host
regardless of IFF_ALLMULTI flag on the interface.
The rule in MC Filter Table in NIC, that is configured to accept any
multicast packets, is turning on if IFF_MULTICAST flag is set on the
interface. It leads to passing all multicast traffic to the host.
This fix changes the condition to turn on that rule by checking
IFF_ALLMULTI flag as it should.
Fixes: b21f502f84 ("net:ethernet:aquantia: Fix for multicast filter handling.")
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3757b255bf ]
Spectrum switch ACL action set is built in groups of three actions
which may point to additional actions. A group holds a single record
which can be set as goto record for pointing at a following group
or can be set to mark the termination of the lookup. This is perfectly
adequate for handling a series of actions to be executed on a packet.
While the SW model allows configuration of conflicting actions
where it is clear that some actions will never execute, the mlxsw
driver must block such configurations as it creates a conflict
over the single terminate/goto record value.
For a conflicting actions configuration such as:
# tc filter add dev swp49 parent ffff: \
protocol ip pref 10 \
flower skip_sw dst_ip 192.168.101.1 \
action goto chain 100 \
action mirred egress mirror dev swp4
Where it is clear that the last action will never execute, the
mlxsw driver was issuing a warning instead of returning an error.
Therefore replace that warning with an error for this specific
case.
Fixes: 4cda7d8d70 ("mlxsw: core: Introduce flexible actions support")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 455f05ecd2 ]
syzbot reported that we reinitialize an active delayed
work in vsock_stream_connect():
ODEBUG: init active (active state 0) object type: timer_list hint:
delayed_work_timer_fn+0x0/0x90 kernel/workqueue.c:1414
WARNING: CPU: 1 PID: 11518 at lib/debugobjects.c:329
debug_print_object+0x16a/0x210 lib/debugobjects.c:326
The pattern is apparently wrong, we should only initialize
the dealyed work once and could repeatly schedule it. So we
have to move out the initializations to allocation side.
And to avoid confusion, we can split the shared dwork
into two, instead of re-using the same one.
Fixes: d021c34405 ("VSOCK: Introduce VM Sockets")
Reported-by: <syzbot+8a9b1bd330476a4f3db6@syzkaller.appspotmail.com>
Cc: Andy king <acking@vmware.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0dcb82254d ]
llc_sap_put() decreases the refcnt before deleting sap
from the global list. Therefore, there is a chance
llc_sap_find() could find a sap with zero refcnt
in this global list.
Close this race condition by checking if refcnt is zero
or not in llc_sap_find(), if it is zero then it is being
removed so we can just treat it as gone.
Reported-by: <syzbot+278893f3f7803871f7ce@syzkaller.appspotmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 61ef4b07fc ]
The shift of 'cwnd' with '(now - hc->tx_lsndtime) / hc->tx_rto' value
can lead to undefined behavior [1].
In order to fix this use a gradual shift of the window with a 'while'
loop, similar to what tcp_cwnd_restart() is doing.
When comparing delta and RTO there is a minor difference between TCP
and DCCP, the last one also invokes dccp_cwnd_restart() and reduces
'cwnd' if delta equals RTO. That case is preserved in this change.
[1]:
[40850.963623] UBSAN: Undefined behaviour in net/dccp/ccids/ccid2.c:237:7
[40851.043858] shift exponent 67 is too large for 32-bit type 'unsigned int'
[40851.127163] CPU: 3 PID: 15940 Comm: netstress Tainted: G W E 4.18.0-rc7.x86_64 #1
...
[40851.377176] Call Trace:
[40851.408503] dump_stack+0xf1/0x17b
[40851.451331] ? show_regs_print_info+0x5/0x5
[40851.503555] ubsan_epilogue+0x9/0x7c
[40851.548363] __ubsan_handle_shift_out_of_bounds+0x25b/0x2b4
[40851.617109] ? __ubsan_handle_load_invalid_value+0x18f/0x18f
[40851.686796] ? xfrm4_output_finish+0x80/0x80
[40851.739827] ? lock_downgrade+0x6d0/0x6d0
[40851.789744] ? xfrm4_prepare_output+0x160/0x160
[40851.845912] ? ip_queue_xmit+0x810/0x1db0
[40851.895845] ? ccid2_hc_tx_packet_sent+0xd36/0x10a0 [dccp]
[40851.963530] ccid2_hc_tx_packet_sent+0xd36/0x10a0 [dccp]
[40852.029063] dccp_xmit_packet+0x1d3/0x720 [dccp]
[40852.086254] dccp_write_xmit+0x116/0x1d0 [dccp]
[40852.142412] dccp_sendmsg+0x428/0xb20 [dccp]
[40852.195454] ? inet_dccp_listen+0x200/0x200 [dccp]
[40852.254833] ? sched_clock+0x5/0x10
[40852.298508] ? sched_clock+0x5/0x10
[40852.342194] ? inet_create+0xdf0/0xdf0
[40852.388988] sock_sendmsg+0xd9/0x160
...
Fixes: 113ced1f52 ("dccp ccid-2: Perform congestion-window validation")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f19f5c49bb upstream.
It turns out that we should *not* invert all not-present mappings,
because the all zeroes case is obviously special.
clear_page() does not undergo the XOR logic to invert the address bits,
i.e. PTE, PMD and PUD entries that have not been individually written
will have val=0 and so will trigger __pte_needs_invert(). As a result,
{pte,pmd,pud}_pfn() will return the wrong PFN value, i.e. all ones
(adjusted by the max PFN mask) instead of zero. A zeroed entry is ok
because the page at physical address 0 is reserved early in boot
specifically to mitigate L1TF, so explicitly exempt them from the
inversion when reading the PFN.
Manifested as an unexpected mprotect(..., PROT_NONE) failure when called
on a VMA that has VM_PFNMAP and was mmap'd to as something other than
PROT_NONE but never used. mprotect() sends the PROT_NONE request down
prot_none_walk(), which walks the PTEs to check the PFNs.
prot_none_pte_entry() gets the bogus PFN from pte_pfn() and returns
-EACCES because it thinks mprotect() is trying to adjust a high MMIO
address.
[ This is a very modified version of Sean's original patch, but all
credit goes to Sean for doing this and also pointing out that
sometimes the __pte_needs_invert() function only gets the protection
bits, not the full eventual pte. But zero remains special even in
just protection bits, so that's ok. - Linus ]
Fixes: f22cc87f6c ("x86/speculation/l1tf: Invert all not present mappings")
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e0fb5df2e upstream.
ioremap() calls pud_free_pmd_page() / pmd_free_pte_page() when it creates
a pud / pmd map. The following preconditions are met at their entry.
- All pte entries for a target pud/pmd address range have been cleared.
- System-wide TLB purges have been peformed for a target pud/pmd address
range.
The preconditions assure that there is no stale TLB entry for the range.
Speculation may not cache TLB entries since it requires all levels of page
entries, including ptes, to have P & A-bits set for an associated address.
However, speculation may cache pud/pmd entries (paging-structure caches)
when they have P-bit set.
Add a system-wide TLB purge (INVLPG) to a single page after clearing
pud/pmd entry's P-bit.
SDM 4.10.4.1, Operation that Invalidate TLBs and Paging-Structure Caches,
states that:
INVLPG invalidates all paging-structure caches associated with the
current PCID regardless of the liner addresses to which they correspond.
Fixes: 28ee90fe60 ("x86/mm: implement free pmd/pte page interfaces")
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: mhocko@suse.com
Cc: akpm@linux-foundation.org
Cc: hpa@zytor.com
Cc: cpandya@codeaurora.org
Cc: linux-mm@kvack.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: Joerg Roedel <joro@8bytes.org>
Cc: stable@vger.kernel.org
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20180627141348.21777-4-toshi.kani@hpe.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8088d3dd4d upstream.
scatterwalk_done() is only meant to be called after a nonzero number of
bytes have been processed, since scatterwalk_pagedone() will flush the
dcache of the *previous* page. But in the error case of
skcipher_walk_done(), e.g. if the input wasn't an integer number of
blocks, scatterwalk_done() was actually called after advancing 0 bytes.
This caused a crash ("BUG: unable to handle kernel paging request")
during '!PageSlab(page)' on architectures like arm and arm64 that define
ARCH_IMPLEMENTS_FLUSH_DCACHE_PAGE, provided that the input was
page-aligned as in that case walk->offset == 0.
Fix it by reorganizing skcipher_walk_done() to skip the
scatterwalk_advance() and scatterwalk_done() if an error has occurred.
This bug was found by syzkaller fuzzing.
Reproducer, assuming ARCH_IMPLEMENTS_FLUSH_DCACHE_PAGE:
#include <linux/if_alg.h>
#include <sys/socket.h>
#include <unistd.h>
int main()
{
struct sockaddr_alg addr = {
.salg_type = "skcipher",
.salg_name = "cbc(aes-generic)",
};
char buffer[4096] __attribute__((aligned(4096))) = { 0 };
int fd;
fd = socket(AF_ALG, SOCK_SEQPACKET, 0);
bind(fd, (void *)&addr, sizeof(addr));
setsockopt(fd, SOL_ALG, ALG_SET_KEY, buffer, 16);
fd = accept(fd, NULL, NULL);
write(fd, buffer, 15);
read(fd, buffer, 15);
}
Reported-by: Liu Chao <liuchao741@huawei.com>
Fixes: b286d8b1a6 ("crypto: skcipher - Add skcipher walk interface")
Cc: <stable@vger.kernel.org> # v4.10+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 318abdfbe7 upstream.
Like the skcipher_walk and blkcipher_walk cases:
scatterwalk_done() is only meant to be called after a nonzero number of
bytes have been processed, since scatterwalk_pagedone() will flush the
dcache of the *previous* page. But in the error case of
ablkcipher_walk_done(), e.g. if the input wasn't an integer number of
blocks, scatterwalk_done() was actually called after advancing 0 bytes.
This caused a crash ("BUG: unable to handle kernel paging request")
during '!PageSlab(page)' on architectures like arm and arm64 that define
ARCH_IMPLEMENTS_FLUSH_DCACHE_PAGE, provided that the input was
page-aligned as in that case walk->offset == 0.
Fix it by reorganizing ablkcipher_walk_done() to skip the
scatterwalk_advance() and scatterwalk_done() if an error has occurred.
Reported-by: Liu Chao <liuchao741@huawei.com>
Fixes: bf06099db1 ("crypto: skcipher - Add ablkcipher_walk interfaces")
Cc: <stable@vger.kernel.org> # v2.6.35+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0868def3e4 upstream.
Like the skcipher_walk case:
scatterwalk_done() is only meant to be called after a nonzero number of
bytes have been processed, since scatterwalk_pagedone() will flush the
dcache of the *previous* page. But in the error case of
blkcipher_walk_done(), e.g. if the input wasn't an integer number of
blocks, scatterwalk_done() was actually called after advancing 0 bytes.
This caused a crash ("BUG: unable to handle kernel paging request")
during '!PageSlab(page)' on architectures like arm and arm64 that define
ARCH_IMPLEMENTS_FLUSH_DCACHE_PAGE, provided that the input was
page-aligned as in that case walk->offset == 0.
Fix it by reorganizing blkcipher_walk_done() to skip the
scatterwalk_advance() and scatterwalk_done() if an error has occurred.
This bug was found by syzkaller fuzzing.
Reproducer, assuming ARCH_IMPLEMENTS_FLUSH_DCACHE_PAGE:
#include <linux/if_alg.h>
#include <sys/socket.h>
#include <unistd.h>
int main()
{
struct sockaddr_alg addr = {
.salg_type = "skcipher",
.salg_name = "ecb(aes-generic)",
};
char buffer[4096] __attribute__((aligned(4096))) = { 0 };
int fd;
fd = socket(AF_ALG, SOCK_SEQPACKET, 0);
bind(fd, (void *)&addr, sizeof(addr));
setsockopt(fd, SOL_ALG, ALG_SET_KEY, buffer, 16);
fd = accept(fd, NULL, NULL);
write(fd, buffer, 15);
read(fd, buffer, 15);
}
Reported-by: Liu Chao <liuchao741@huawei.com>
Fixes: 5cde0af2a9 ("[CRYPTO] cipher: Added block cipher type")
Cc: <stable@vger.kernel.org> # v2.6.19+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb29648102 upstream.
syzbot reported a crash in vmac_final() when multiple threads
concurrently use the same "vmac(aes)" transform through AF_ALG. The bug
is pretty fundamental: the VMAC template doesn't separate per-request
state from per-tfm (per-key) state like the other hash algorithms do,
but rather stores it all in the tfm context. That's wrong.
Also, vmac_final() incorrectly zeroes most of the state including the
derived keys and cached pseudorandom pad. Therefore, only the first
VMAC invocation with a given key calculates the correct digest.
Fix these bugs by splitting the per-tfm state from the per-request state
and using the proper init/update/final sequencing for requests.
Reproducer for the crash:
#include <linux/if_alg.h>
#include <sys/socket.h>
#include <unistd.h>
int main()
{
int fd;
struct sockaddr_alg addr = {
.salg_type = "hash",
.salg_name = "vmac(aes)",
};
char buf[256] = { 0 };
fd = socket(AF_ALG, SOCK_SEQPACKET, 0);
bind(fd, (void *)&addr, sizeof(addr));
setsockopt(fd, SOL_ALG, ALG_SET_KEY, buf, 16);
fork();
fd = accept(fd, NULL, NULL);
for (;;)
write(fd, buf, 256);
}
The immediate cause of the crash is that vmac_ctx_t.partial_size exceeds
VMAC_NHBYTES, causing vmac_final() to memset() a negative length.
Reported-by: syzbot+264bca3a6e8d645550d3@syzkaller.appspotmail.com
Fixes: f1939f7c56 ("crypto: vmac - New hash algorithm for intel_txt support")
Cc: <stable@vger.kernel.org> # v2.6.32+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 73bf20ef3d upstream.
The VMAC template assumes the block cipher has a 128-bit block size, but
it failed to check for that. Thus it was possible to instantiate it
using a 64-bit block size cipher, e.g. "vmac(cast5)", causing
uninitialized memory to be used.
Add the needed check when instantiating the template.
Fixes: f1939f7c56 ("crypto: vmac - New hash algorithm for intel_txt support")
Cc: <stable@vger.kernel.org> # v2.6.32+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f426d2b20f upstream.
The wait_event() function is used to detect command completion. The
interrupt handler will set the wait condition variable when the interrupt
is triggered. However, the variable used for wait_event() is initialized
after the command has been submitted, which can create a race condition
with the interrupt handler and result in the wait_event() never returning.
Move the initialization of the wait condition variable to just before
command submission.
Fixes: 200664d523 ("crypto: ccp: Add Secure Encrypted Virtualization (SEV) command support")
Cc: <stable@vger.kernel.org> # 4.16.x-
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Reviewed-by: Brijesh Singh <brijesh.singh@amd.com>
Acked-by: Gary R Hook <gary.hook@amd.com>
Acked-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit afb31cd2d1 upstream.
Should the PSP initialization fail, the PSP data structure will be
freed and the value contained in the sp_device struct set to NULL.
At module unload, psp_dev_destroy() does not check if the pointer
value is NULL and will end up dereferencing a NULL pointer.
Add a pointer check of the psp_data field in the sp_device struct
in psp_dev_destroy() and return immediately if it is NULL.
Cc: <stable@vger.kernel.org> # 4.16.x-
Fixes: 2a6170dfe7 ("crypto: ccp: Add Platform Security Processor (PSP) device support")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Acked-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 00904aa0cd upstream.
We were copying our last cipher block into the request for use as IV for
all modes of operations. Fix this by discerning the behaviour based on
the mode of operation used: copy ciphertext for CBC, update counter for
CTR.
CC: stable@vger.kernel.org
Fixes: 63ee04c8b4 ("crypto: ccree - add skcipher support")
Reported by: Hadar Gat <hadar.gat@arm.com>
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 405c018a25 upstream.
Commit d94a155c59 ("x86/cpu: Prevent cpuinfo_x86::x86_phys_bits
adjustment corruption") has moved the query and calculation of the
x86_virt_bits and x86_phys_bits fields of the cpuinfo_x86 struct
from the get_cpu_cap function to a new function named
get_cpu_address_sizes.
One of the call sites related to Xen PV VMs was unfortunately missed
in the aforementioned commit. This prevents successful boot-up of
kernel versions 4.17 and up in Xen PV VMs if CONFIG_DEBUG_VIRTUAL
is enabled, due to the following code path:
enlighten_pv.c::xen_start_kernel
mmu_pv.c::xen_reserve_special_pages
page.h::__pa
physaddr.c::__phys_addr
physaddr.h::phys_addr_valid
phys_addr_valid uses boot_cpu_data.x86_phys_bits to validate physical
addresses. boot_cpu_data.x86_phys_bits is no longer populated before
the call to xen_reserve_special_pages due to the aforementioned commit
though, so the validation performed by phys_addr_valid fails, which
causes __phys_addr to trigger a BUG, preventing boot-up.
Signed-off-by: M. Vefa Bicakci <m.v.b@runbox.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: xen-devel@lists.xenproject.org
Cc: x86@kernel.org
Cc: stable@vger.kernel.org # for v4.17 and up
Fixes: d94a155c59 ("x86/cpu: Prevent cpuinfo_x86::x86_phys_bits adjustment corruption")
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eac7073aa6 upstream.
The kernel image starts out with the Global bit set across the entire
kernel image. The bit is cleared with set_memory_nonglobal() in the
configurations with PCIDs where the performance benefits of the Global bit
are not needed.
However, this is fragile. It means that we are stuck opting *out* of the
less-secure (Global bit set) configuration, which seems backwards. Let's
start more secure (Global bit clear) and then let things opt back in if
they want performance, or are truly mapping common data between kernel and
userspace.
This fixes a bug. Before this patch, there are areas that are unmapped
from the user page tables (like like everything above 0xffffffff82600000 in
the example below). These have the hallmark of being a wrong Global area:
they are not identical in the 'current_kernel' and 'current_user' page
table dumps. They are also read-write, which means they're much more
likely to contain secrets.
Before this patch:
current_kernel:---[ High Kernel Mapping ]---
current_kernel-0xffffffff80000000-0xffffffff81000000 16M pmd
current_kernel-0xffffffff81000000-0xffffffff81e00000 14M ro PSE GLB x pmd
current_kernel-0xffffffff81e00000-0xffffffff81e11000 68K ro GLB x pte
current_kernel-0xffffffff81e11000-0xffffffff82000000 1980K RW GLB NX pte
current_kernel-0xffffffff82000000-0xffffffff82600000 6M ro PSE GLB NX pmd
current_kernel-0xffffffff82600000-0xffffffff82c00000 6M RW PSE GLB NX pmd
current_kernel-0xffffffff82c00000-0xffffffff82e00000 2M RW GLB NX pte
current_kernel-0xffffffff82e00000-0xffffffff83200000 4M RW PSE GLB NX pmd
current_kernel-0xffffffff83200000-0xffffffffa0000000 462M pmd
current_user:---[ High Kernel Mapping ]---
current_user-0xffffffff80000000-0xffffffff81000000 16M pmd
current_user-0xffffffff81000000-0xffffffff81e00000 14M ro PSE GLB x pmd
current_user-0xffffffff81e00000-0xffffffff81e11000 68K ro GLB x pte
current_user-0xffffffff81e11000-0xffffffff82000000 1980K RW GLB NX pte
current_user-0xffffffff82000000-0xffffffff82600000 6M ro PSE GLB NX pmd
current_user-0xffffffff82600000-0xffffffffa0000000 474M pmd
After this patch:
current_kernel:---[ High Kernel Mapping ]---
current_kernel-0xffffffff80000000-0xffffffff81000000 16M pmd
current_kernel-0xffffffff81000000-0xffffffff81e00000 14M ro PSE GLB x pmd
current_kernel-0xffffffff81e00000-0xffffffff81e11000 68K ro GLB x pte
current_kernel-0xffffffff81e11000-0xffffffff82000000 1980K RW NX pte
current_kernel-0xffffffff82000000-0xffffffff82600000 6M ro PSE GLB NX pmd
current_kernel-0xffffffff82600000-0xffffffff82c00000 6M RW PSE NX pmd
current_kernel-0xffffffff82c00000-0xffffffff82e00000 2M RW NX pte
current_kernel-0xffffffff82e00000-0xffffffff83200000 4M RW PSE NX pmd
current_kernel-0xffffffff83200000-0xffffffffa0000000 462M pmd
current_user:---[ High Kernel Mapping ]---
current_user-0xffffffff80000000-0xffffffff81000000 16M pmd
current_user-0xffffffff81000000-0xffffffff81e00000 14M ro PSE GLB x pmd
current_user-0xffffffff81e00000-0xffffffff81e11000 68K ro GLB x pte
current_user-0xffffffff81e11000-0xffffffff82000000 1980K RW NX pte
current_user-0xffffffff82000000-0xffffffff82600000 6M ro PSE GLB NX pmd
current_user-0xffffffff82600000-0xffffffffa0000000 474M pmd
Fixes: 0f561fce4d ("x86/pti: Enable global pages for shared areas")
Reported-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: keescook@google.com
Cc: aarcange@redhat.com
Cc: jgross@suse.com
Cc: jpoimboe@redhat.com
Cc: gregkh@linuxfoundation.org
Cc: peterz@infradead.org
Cc: torvalds@linux-foundation.org
Cc: bp@alien8.de
Cc: luto@kernel.org
Cc: ak@linux.intel.com
Cc: Kees Cook <keescook@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Link: https://lkml.kernel.org/r/20180802225825.A100C071@viggo.jf.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0a957467c5 upstream.
i8259.h uses inb/outb and thus needs to include asm/io.h to avoid the
following build error, as seen with x86_64:defconfig and CONFIG_SMP=n.
In file included from drivers/rtc/rtc-cmos.c:45:0:
arch/x86/include/asm/i8259.h: In function 'inb_pic':
arch/x86/include/asm/i8259.h:32:24: error:
implicit declaration of function 'inb'
arch/x86/include/asm/i8259.h: In function 'outb_pic':
arch/x86/include/asm/i8259.h:45:2: error:
implicit declaration of function 'outb'
Reported-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Suggested-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Fixes: 447ae31667 ("x86: Don't include linux/irq.h from asm/hardirq.h")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 792adb90fa upstream.
The introduction of generic_max_swapfile_size and arch-specific versions has
broken linking on x86 with CONFIG_SWAP=n due to undefined reference to
'generic_max_swapfile_size'. Fix it by compiling the x86-specific
max_swapfile_size() only with CONFIG_SWAP=y.
Reported-by: Tomas Pruzina <pruzinat@gmail.com>
Fixes: 377eeaa8e1 ("x86/speculation/l1tf: Limit swap file size to MAX_PA/2")
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 269777aa53 upstream.
Commit 0cc3cd2165 ("cpu/hotplug: Boot HT siblings at least once")
breaks non-SMP builds.
[ I suspect the 'bool' fields should just be made to be bitfields and be
exposed regardless of configuration, but that's a separate cleanup
that I'll leave to the owners of this file for later. - Linus ]
Fixes: 0cc3cd2165 ("cpu/hotplug: Boot HT siblings at least once")
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Abel Vesa <abelvesa@linux.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0055f351e upstream.
The function has an inline "return false;" definition with CONFIG_SMP=n
but the "real" definition is also visible leading to "redefinition of
‘apic_id_is_primary_thread’" compiler error.
Guard it with #ifdef CONFIG_SMP
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Fixes: 6a4d2657e0 ("x86/smp: Provide topology_is_primary_thread()")
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07d981ad4c upstream
The kernel unnecessarily prevents late microcode loading when SMT is
disabled. It should be safe to allow it if all the primary threads are
online.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 63b89a19cc upstream
To pick up changes from:
$ git log --oneline -2 -i include/uapi/linux/prctl.h
356e4bfff2 prctl: Add force disable speculation
b617cfc858 prctl: Add speculation control prctls
$ tools/perf/trace/beauty/prctl_option.sh > before.c
$ cp include/uapi/linux/prctl.h tools/include/uapi/linux/prctl.h
$ tools/perf/trace/beauty/prctl_option.sh > after.c
$ diff -u before.c after.c
# --- before.c 2018-06-01 10:39:53.834073962 -0300
# +++ after.c 2018-06-01 10:42:11.307985394 -0300
@@ -35,6 +35,8 @@
[42] = "GET_THP_DISABLE",
[45] = "SET_FP_MODE",
[46] = "GET_FP_MODE",
+ [52] = "GET_SPECULATION_CTRL",
+ [53] = "SET_SPECULATION_CTRL",
};
static const char *prctl_set_mm_options[] = {
[1] = "START_CODE",
$
This will be used by 'perf trace' to show these strings when beautifying
the prctl syscall args. At some point we'll be able to say something
like:
'perf trace --all-cpus -e prctl(option=*SPEC*)'
To filter by arg by name.
This silences this warning when building tools/perf:
Warning: Kernel ABI header at 'tools/include/uapi/linux/prctl.h' differs from latest version at 'include/uapi/linux/prctl.h'
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wang Nan <wangnan0@huawei.com>
Link: https://lkml.kernel.org/n/tip-zztsptwhc264r8wg44tqh5gp@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1063711b57 upstream
The mmio tracer sets io mapping PTEs and PMDs to non present when enabled
without inverting the address bits, which makes the PTE entry vulnerable
for L1TF.
Make it use the right low level macros to actually invert the address bits
to protect against L1TF.
In principle this could be avoided because MMIO tracing is not likely to be
enabled on production machines, but the fix is straigt forward and for
consistency sake it's better to get rid of the open coded PTE manipulation.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 958f79b9ee upstream
set_memory_np() is used to mark kernel mappings not present, but it has
it's own open coded mechanism which does not have the L1TF protection of
inverting the address bits.
Replace the open coded PTE manipulation with the L1TF protecting low level
PTE routines.
Passes the CPA self test.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0768f91530 upstream
Some cases in THP like:
- MADV_FREE
- mprotect
- split
mark the PMD non present for temporarily to prevent races. The window for
an L1TF attack in these contexts is very small, but it wants to be fixed
for correctness sake.
Use the proper low level functions for pmd/pud_mknotpresent() to address
this.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f22cc87f6c upstream
For kernel mappings PAGE_PROTNONE is not necessarily set for a non present
mapping, but the inversion logic explicitely checks for !PRESENT and
PROT_NONE.
Remove the PROT_NONE check and make the inversion unconditional for all not
present mappings.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bc2d8d262c upstream
Josh reported that the late SMT evaluation in cpu_smt_state_init() sets
cpu_smt_control to CPU_SMT_NOT_SUPPORTED in case that 'nosmt' was supplied
on the kernel command line as it cannot differentiate between SMT disabled
by BIOS and SMT soft disable via 'nosmt'. That wreckages the state and
makes the sysfs interface unusable.
Rework this so that during bringup of the non boot CPUs the availability of
SMT is determined in cpu_smt_allowed(). If a newly booted CPU is not a
'primary' thread then set the local cpu_smt_available marker and evaluate
this explicitely right after the initial SMP bringup has finished.
SMT evaulation on x86 is a trainwreck as the firmware has all the
information _before_ booting the kernel, but there is no interface to query
it.
Fixes: 73d5e2b472 ("cpu/hotplug: detect SMT disabled by BIOS")
Reported-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b76a3cff0 upstream
When nested virtualization is in use, VMENTER operations from the nested
hypervisor into the nested guest will always be processed by the bare metal
hypervisor, and KVM's "conditional cache flushes" mode in particular does a
flush on nested vmentry. Therefore, include the "skip L1D flush on
vmentry" bit in KVM's suggested ARCH_CAPABILITIES setting.
Add the relevant Documentation.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e0b2b9166 upstream
Bit 3 of ARCH_CAPABILITIES tells a hypervisor that L1D flush on vmentry is
not needed. Add a new value to enum vmx_l1d_flush_state, which is used
either if there is no L1TF bug at all, or if bit 3 is set in ARCH_CAPABILITIES.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea156d192f upstream
Three changes to the content of the sysfs file:
- If EPT is disabled, L1TF cannot be exploited even across threads on the
same core, and SMT is irrelevant.
- If mitigation is completely disabled, and SMT is enabled, print "vulnerable"
instead of "vulnerable, SMT vulnerable"
- Reorder the two parts so that the main vulnerability state comes first
and the detail on SMT is second.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 18b57ce2eb upstream
For VMEXITs caused by external interrupts, vmx_handle_external_intr()
indirectly calls into the interrupt handlers through the host's IDT.
It follows that these interrupts get accounted for in the
kvm_cpu_l1tf_flush_l1d per-cpu flag.
The subsequently executed vmx_l1d_flush() will thus be aware that some
interrupts have happened and conduct a L1d flush anyway.
Setting l1tf_flush_l1d from vmx_handle_external_intr() isn't needed
anymore. Drop it.
Signed-off-by: Nicolai Stange <nstange@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ffcba43ff6 upstream
The last missing piece to having vmx_l1d_flush() take interrupts after
VMEXIT into account is to set the kvm_cpu_l1tf_flush_l1d per-cpu flag on
irq entry.
Issue calls to kvm_set_cpu_l1tf_flush_l1d() from entering_irq(),
ipi_entering_ack_irq(), smp_reschedule_interrupt() and
uv_bau_message_interrupt().
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Nicolai Stange <nstange@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 447ae31667 upstream
The next patch in this series will have to make the definition of
irq_cpustat_t available to entering_irq().
Inclusion of asm/hardirq.h into asm/apic.h would cause circular header
dependencies like
asm/smp.h
asm/apic.h
asm/hardirq.h
linux/irq.h
linux/topology.h
linux/smp.h
asm/smp.h
or
linux/gfp.h
linux/mmzone.h
asm/mmzone.h
asm/mmzone_64.h
asm/smp.h
asm/apic.h
asm/hardirq.h
linux/irq.h
linux/irqdesc.h
linux/kobject.h
linux/sysfs.h
linux/kernfs.h
linux/idr.h
linux/gfp.h
and others.
This causes compilation errors because of the header guards becoming
effective in the second inclusion: symbols/macros that had been defined
before wouldn't be available to intermediate headers in the #include chain
anymore.
A possible workaround would be to move the definition of irq_cpustat_t
into its own header and include that from both, asm/hardirq.h and
asm/apic.h.
However, this wouldn't solve the real problem, namely asm/harirq.h
unnecessarily pulling in all the linux/irq.h cruft: nothing in
asm/hardirq.h itself requires it. Also, note that there are some other
archs, like e.g. arm64, which don't have that #include in their
asm/hardirq.h.
Remove the linux/irq.h #include from x86' asm/hardirq.h.
Fix resulting compilation errors by adding appropriate #includes to *.c
files as needed.
Note that some of these *.c files could be cleaned up a bit wrt. to their
set of #includes, but that should better be done from separate patches, if
at all.
Signed-off-by: Nicolai Stange <nstange@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45b575c00d upstream
Part of the L1TF mitigation for vmx includes flushing the L1D cache upon
VMENTRY.
L1D flushes are costly and two modes of operations are provided to users:
"always" and the more selective "conditional" mode.
If operating in the latter, the cache would get flushed only if a host side
code path considered unconfined had been traversed. "Unconfined" in this
context means that it might have pulled in sensitive data like user data
or kernel crypto keys.
The need for L1D flushes is tracked by means of the per-vcpu flag
l1tf_flush_l1d. KVM exit handlers considered unconfined set it. A
vmx_l1d_flush() subsequently invoked before the next VMENTER will conduct a
L1d flush based on its value and reset that flag again.
Currently, interrupts delivered "normally" while in root operation between
VMEXIT and VMENTER are not taken into account. Part of the reason is that
these don't leave any traces and thus, the vmx code is unable to tell if
any such has happened.
As proposed by Paolo Bonzini, prepare for tracking all interrupts by
introducing a new per-cpu flag, "kvm_cpu_l1tf_flush_l1d". It will be in
strong analogy to the per-vcpu ->l1tf_flush_l1d.
A later patch will make interrupt handlers set it.
For the sake of cache locality, group kvm_cpu_l1tf_flush_l1d into x86'
per-cpu irq_cpustat_t as suggested by Peter Zijlstra.
Provide the helpers kvm_set_cpu_l1tf_flush_l1d(),
kvm_clear_cpu_l1tf_flush_l1d() and kvm_get_cpu_l1tf_flush_l1d(). Make them
trivial resp. non-existent for !CONFIG_KVM_INTEL as appropriate.
Let vmx_l1d_flush() handle kvm_cpu_l1tf_flush_l1d in the same way as
l1tf_flush_l1d.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Nicolai Stange <nstange@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9aee5f8a7e upstream
An upcoming patch will extend KVM's L1TF mitigation in conditional mode
to also cover interrupts after VMEXITs. For tracking those, stores to a
new per-cpu flag from interrupt handlers will become necessary.
In order to improve cache locality, this new flag will be added to x86's
irq_cpustat_t.
Make some space available there by shrinking the ->softirq_pending bitfield
from 32 to 16 bits: the number of bits actually used is only NR_SOFTIRQS,
i.e. 10.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Nicolai Stange <nstange@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b6ccc6c3b upstream
Currently, vmx_vcpu_run() checks if l1tf_flush_l1d is set and invokes
vmx_l1d_flush() if so.
This test is unncessary for the "always flush L1D" mode.
Move the check to vmx_l1d_flush()'s conditional mode code path.
Notes:
- vmx_l1d_flush() is likely to get inlined anyway and thus, there's no
extra function call.
- This inverts the (static) branch prediction, but there hadn't been any
explicit likely()/unlikely() annotations before and so it stays as is.
Signed-off-by: Nicolai Stange <nstange@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 427362a142 upstream
The vmx_l1d_flush_always static key is only ever evaluated if
vmx_l1d_should_flush is enabled. In that case however, there are only two
L1d flushing modes possible: "always" and "conditional".
The "conditional" mode's implementation tends to require more sophisticated
logic than the "always" mode.
Avoid inverted logic by replacing the 'vmx_l1d_flush_always' static key
with a 'vmx_l1d_flush_cond' one.
There is no change in functionality.
Signed-off-by: Nicolai Stange <nstange@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 379fd0c7e6 upstream
vmx_l1d_flush() gets invoked only if l1tf_flush_l1d is true. There's no
point in setting l1tf_flush_l1d to true from there again.
Signed-off-by: Nicolai Stange <nstange@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 73d5e2b472 upstream
If SMT is disabled in BIOS, the CPU code doesn't properly detect it.
The /sys/devices/system/cpu/smt/control file shows 'on', and the 'l1tf'
vulnerabilities file shows SMT as vulnerable.
Fix it by forcing 'cpu_smt_control' to CPU_SMT_NOT_SUPPORTED in such a
case. Unfortunately the detection can only be done after bringing all
the CPUs online, so we have to overwrite any previous writes to the
variable.
Reported-by: Joe Mario <jmario@redhat.com>
Tested-by: Jiri Kosina <jkosina@suse.cz>
Fixes: f048c399e0 ("x86/topology: Provide topology_smt_supported()")
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 288d152c23 upstream
The slow path in vmx_l1d_flush() reads from vmx_l1d_flush_pages in order
to evict the L1d cache.
However, these pages are never cleared and, in theory, their data could be
leaked.
More importantly, KSM could merge a nested hypervisor's vmx_l1d_flush_pages
to fewer than 1 << L1D_CACHE_ORDER host physical pages and this would break
the L1d flushing algorithm: L1D on x86_64 is tagged by physical addresses.
Fix this by initializing the individual vmx_l1d_flush_pages with a
different pattern each.
Rename the "empty_zp" asm constraint identifier in vmx_l1d_flush() to
"flush_pages" to reflect this change.
Fixes: a47dd5f067 ("x86/KVM/VMX: Add L1D flush algorithm")
Signed-off-by: Nicolai Stange <nstange@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c26fcd2ab upstream
pfn_modify_allowed() and arch_has_pfn_modify_check() are outside of the
!__ASSEMBLY__ section in include/asm-generic/pgtable.h, which confuses
assembler on archs that don't have __HAVE_ARCH_PFN_MODIFY_ALLOWED (e.g.
ia64) and breaks build:
include/asm-generic/pgtable.h: Assembler messages:
include/asm-generic/pgtable.h:538: Error: Unknown opcode `static inline bool pfn_modify_allowed(unsigned long pfn,pgprot_t prot)'
include/asm-generic/pgtable.h:540: Error: Unknown opcode `return true'
include/asm-generic/pgtable.h:543: Error: Unknown opcode `static inline bool arch_has_pfn_modify_check(void)'
include/asm-generic/pgtable.h:545: Error: Unknown opcode `return false'
arch/ia64/kernel/entry.S:69: Error: `mov' does not fit into bundle
Move those two static inlines into the !__ASSEMBLY__ section so that they
don't confuse the asm build pass.
Fixes: 42e4089c78 ("x86/speculation/l1tf: Disallow non privileged high MMIO PROT_NONE mappings")
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d90a7a0ec8 upstream
Introduce the 'l1tf=' kernel command line option to allow for boot-time
switching of mitigation that is used on processors affected by L1TF.
The possible values are:
full
Provides all available mitigations for the L1TF vulnerability. Disables
SMT and enables all mitigations in the hypervisors. SMT control via
/sys/devices/system/cpu/smt/control is still possible after boot.
Hypervisors will issue a warning when the first VM is started in
a potentially insecure configuration, i.e. SMT enabled or L1D flush
disabled.
full,force
Same as 'full', but disables SMT control. Implies the 'nosmt=force'
command line option. sysfs control of SMT and the hypervisor flush
control is disabled.
flush
Leaves SMT enabled and enables the conditional hypervisor mitigation.
Hypervisors will issue a warning when the first VM is started in a
potentially insecure configuration, i.e. SMT enabled or L1D flush
disabled.
flush,nosmt
Disables SMT and enables the conditional hypervisor mitigation. SMT
control via /sys/devices/system/cpu/smt/control is still possible
after boot. If SMT is reenabled or flushing disabled at runtime
hypervisors will issue a warning.
flush,nowarn
Same as 'flush', but hypervisors will not warn when
a VM is started in a potentially insecure configuration.
off
Disables hypervisor mitigations and doesn't emit any warnings.
Default is 'flush'.
Let KVM adhere to these semantics, which means:
- 'lt1f=full,force' : Performe L1D flushes. No runtime control
possible.
- 'l1tf=full'
- 'l1tf-flush'
- 'l1tf=flush,nosmt' : Perform L1D flushes and warn on VM start if
SMT has been runtime enabled or L1D flushing
has been run-time enabled
- 'l1tf=flush,nowarn' : Perform L1D flushes and no warnings are emitted.
- 'l1tf=off' : L1D flushes are not performed and no warnings
are emitted.
KVM can always override the L1D flushing behavior using its 'vmentry_l1d_flush'
module parameter except when lt1f=full,force is set.
This makes KVM's private 'nosmt' option redundant, and as it is a bit
non-systematic anyway (this is something to control globally, not on
hypervisor level), remove that option.
Add the missing Documentation entry for the l1tf vulnerability sysfs file
while at it.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Jiri Kosina <jkosina@suse.cz>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lkml.kernel.org/r/20180713142323.202758176@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fee0aede6f upstream
The CPU_SMT_NOT_SUPPORTED state is set (if the processor does not support
SMT) when the sysfs SMT control file is initialized.
That was fine so far as this was only required to make the output of the
control file correct and to prevent writes in that case.
With the upcoming l1tf command line parameter, this needs to be set up
before the L1TF mitigation selection and command line parsing happens.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Jiri Kosina <jkosina@suse.cz>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lkml.kernel.org/r/20180713142323.121795971@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7db92e165a upstream
In preparation of allowing run time control for L1D flushing, move the
setup code to the module parameter handler.
In case of pre module init parsing, just store the value and let vmx_init()
do the actual setup after running kvm_init() so that enable_ept is having
the correct state.
During run-time invoke it directly from the parameter setter to prepare for
run-time control.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Jiri Kosina <jkosina@suse.cz>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lkml.kernel.org/r/20180713142322.694063239@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f055947ae upstream
The VMX module parameter to control the L1D flush should become
writeable.
The MSR list is set up at VM init per guest VCPU, but the run time
switching is based on a static key which is global. Toggling the MSR list
at run time might be feasible, but for now drop this optimization and use
the regular MSR write to make run-time switching possible.
The default mitigation is the conditional flush anyway, so for extra
paranoid setups this will add some small overhead, but the extra code
executed is in the noise compared to the flush itself.
Aside of that the EPT disabled case is not handled correctly at the moment
and the MSR list magic is in the way for fixing that as well.
If it's really providing a significant advantage, then this needs to be
revisited after the code is correct and the control is writable.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Jiri Kosina <jkosina@suse.cz>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lkml.kernel.org/r/20180713142322.516940445@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 215af5499d upstream
Writing 'off' to /sys/devices/system/cpu/smt/control offlines all SMT
siblings. Writing 'on' merily enables the abilify to online them, but does
not online them automatically.
Make 'on' more useful by onlining all offline siblings.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 390d975e0c upstream
If the L1D flush module parameter is set to 'always' and the IA32_FLUSH_CMD
MSR is available, optimize the VMENTER code with the MSR save list.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 989e3992d2 upstream
The IA32_FLUSH_CMD MSR needs only to be written on VMENTER. Extend
add_atomic_switch_msr() with an entry_only parameter to allow storing the
MSR only in the guest (ENTRY) MSR array.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 33966dd6b2 upstream
There is no semantic change but this change allows an unbalanced amount of
MSRs to be loaded on VMEXIT and VMENTER, i.e. the number of MSRs to save or
restore on VMEXIT or VMENTER may be different.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c595ceee45 upstream
Add the logic for flushing L1D on VMENTER. The flush depends on the static
key being enabled and the new l1tf_flush_l1d flag being set.
The flags is set:
- Always, if the flush module parameter is 'always'
- Conditionally at:
- Entry to vcpu_run(), i.e. after executing user space
- From the sched_in notifier, i.e. when switching to a vCPU thread.
- From vmexit handlers which are considered unsafe, i.e. where
sensitive data can be brought into L1D:
- The emulator, which could be a good target for other speculative
execution-based threats,
- The MMU, which can bring host page tables in the L1 cache.
- External interrupts
- Nested operations that require the MMU (see above). That is
vmptrld, vmptrst, vmclear,vmwrite,vmread.
- When handling invept,invvpid
[ tglx: Split out from combo patch and reduced to a single flag ]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3fa045be4c upstream
336996-Speculative-Execution-Side-Channel-Mitigations.pdf defines a new MSR
(IA32_FLUSH_CMD aka 0x10B) which has similar write-only semantics to other
MSRs defined in the document.
The semantics of this MSR is to allow "finer granularity invalidation of
caching structures than existing mechanisms like WBINVD. It will writeback
and invalidate the L1 data cache, including all cachelines brought in by
preceding instructions, without invalidating all caches (eg. L2 or
LLC). Some processors may also invalidate the first level level instruction
cache on a L1D_FLUSH command. The L1 data and instruction caches may be
shared across the logical processors of a core."
Use it instead of the loop based L1 flush algorithm.
A copy of this document is available at
https://bugzilla.kernel.org/show_bug.cgi?id=199511
[ tglx: Avoid allocating pages when the MSR is available ]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a47dd5f067 upstream
To mitigate the L1 Terminal Fault vulnerability it's required to flush L1D
on VMENTER to prevent rogue guests from snooping host memory.
CPUs will have a new control MSR via a microcode update to flush L1D with a
single MSR write, but in the absence of microcode a fallback to a software
based flush algorithm is required.
Add a software flush loop which is based on code from Intel.
[ tglx: Split out from combo patch ]
[ bpetkov: Polish the asm code ]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a399477e52 upstream
Add a mitigation mode parameter "vmentry_l1d_flush" for CVE-2018-3620, aka
L1 terminal fault. The valid arguments are:
- "always" L1D cache flush on every VMENTER.
- "cond" Conditional L1D cache flush, explained below
- "never" Disable the L1D cache flush mitigation
"cond" is trying to avoid L1D cache flushes on VMENTER if the code executed
between VMEXIT and VMENTER is considered safe, i.e. is not bringing any
interesting information into L1D which might exploited.
[ tglx: Split out from a larger patch ]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26acfb666a upstream
If the L1TF CPU bug is present we allow the KVM module to be loaded as the
major of users that use Linux and KVM have trusted guests and do not want a
broken setup.
Cloud vendors are the ones that are uncomfortable with CVE 2018-3620 and as
such they are the ones that should set nosmt to one.
Setting 'nosmt' means that the system administrator also needs to disable
SMT (Hyper-threading) in the BIOS, or via the 'nosmt' command line
parameter, or via the /sys/devices/system/cpu/smt/control. See commit
05736e4ac1 ("cpu/hotplug: Provide knobs to control SMT").
Other mitigations are to use task affinity, cpu sets, interrupt binding,
etc - anything to make sure that _only_ the same guests vCPUs are running
on sibling threads.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0cc3cd2165 upstream
Due to the way Machine Check Exceptions work on X86 hyperthreads it's
required to boot up _all_ logical cores at least once in order to set the
CR4.MCE bit.
So instead of ignoring the sibling threads right away, let them boot up
once so they can configure themselves. After they came out of the initial
boot stage check whether its a "secondary" sibling and cancel the operation
which puts the CPU back into offline state.
Reported-by: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 506a66f374 upstream
Dave Hansen reported, that it's outright dangerous to keep SMT siblings
disabled completely so they are stuck in the BIOS and wait for SIPI.
The reason is that Machine Check Exceptions are broadcasted to siblings and
the soft disabled sibling has CR4.MCE = 0. If a MCE is delivered to a
logical core with CR4.MCE = 0, it asserts IERR#, which shuts down or
reboots the machine. The MCE chapter in the SDM contains the following
blurb:
Because the logical processors within a physical package are tightly
coupled with respect to shared hardware resources, both logical
processors are notified of machine check errors that occur within a
given physical processor. If machine-check exceptions are enabled when
a fatal error is reported, all the logical processors within a physical
package are dispatched to the machine-check exception handler. If
machine-check exceptions are disabled, the logical processors enter the
shutdown state and assert the IERR# signal. When enabling machine-check
exceptions, the MCE flag in control register CR4 should be set for each
logical processor.
Reverting the commit which ignores siblings at enumeration time solves only
half of the problem. The core cpuhotplug logic needs to be adjusted as
well.
This thoughtful engineered mechanism also turns the boot process on all
Intel HT enabled systems into a MCE lottery. MCE is enabled on the boot CPU
before the secondary CPUs are brought up. Depending on the number of
physical cores the window in which this situation can happen is smaller or
larger. On a HSW-EX it's about 750ms:
MCE is enabled on the boot CPU:
[ 0.244017] mce: CPU supports 22 MCE banks
The corresponding sibling #72 boots:
[ 1.008005] .... node #0, CPUs: #72
That means if an MCE hits on physical core 0 (logical CPUs 0 and 72)
between these two points the machine is going to shutdown. At least it's a
known safe state.
It's obvious that the early boot can be hit by an MCE as well and then runs
into the same situation because MCEs are not yet enabled on the boot CPU.
But after enabling them on the boot CPU, it does not make any sense to
prevent the kernel from recovering.
Adjust the nosmt kernel parameter documentation as well.
Reverts: 2207def700 ("x86/apic: Ignore secondary threads if nosmt=force")
Reported-by: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e14d7dfb41 upstream
Jan has noticed that pte_pfn and co. resp. pfn_pte are incorrect for
CONFIG_PAE because phys_addr_t is wider than unsigned long and so the
pte_val reps. shift left would get truncated. Fix this up by using proper
types.
Fixes: 6b28baca9b ("x86/speculation/l1tf: Protect PROT_NONE PTEs against speculation")
Reported-by: Jan Beulich <JBeulich@suse.com>
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0d0f624905 upstream
The PAE 3-level paging code currently doesn't mitigate L1TF by flipping the
offset bits, and uses the high PTE word, thus bits 32-36 for type, 37-63 for
offset. The lower word is zeroed, thus systems with less than 4GB memory are
safe. With 4GB to 128GB the swap type selects the memory locations vulnerable
to L1TF; with even more memory, also the swap offfset influences the address.
This might be a problem with 32bit PAE guests running on large 64bit hosts.
By continuing to keep the whole swap entry in either high or low 32bit word of
PTE we would limit the swap size too much. Thus this patch uses the whole PAE
PTE with the same layout as the 64bit version does. The macros just become a
bit tricky since they assume the arch-dependent swp_entry_t to be 32bit.
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ce2f0393e upstream
The TOPOEXT reenablement is a workaround for broken BIOSen which didn't
enable the CPUID bit. amd_get_topology_early(), however, relies on
that bit being set so that it can read out the CPUID leaf and set
smp_num_siblings properly.
Move the reenablement up to early_init_amd(). While at it, simplify
amd_get_topology_early().
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 11e34e64e4 upstream
336996-Speculative-Execution-Side-Channel-Mitigations.pdf defines a new MSR
(IA32_FLUSH_CMD) which is detected by CPUID.7.EDX[28]=1 bit being set.
This new MSR "gives software a way to invalidate structures with finer
granularity than other architectual methods like WBINVD."
A copy of this document is available at
https://bugzilla.kernel.org/show_bug.cgi?id=199511
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a7ed1ba4b upstream
The previous patch has limited swap file size so that large offsets cannot
clear bits above MAX_PA/2 in the pte and interfere with L1TF mitigation.
It assumed that offsets are encoded starting with bit 12, same as pfn. But
on x86_64, offsets are encoded starting with bit 9.
Thus the limit can be raised by 3 bits. That means 16TB with 42bit MAX_PA
and 256TB with 46bit MAX_PA.
Fixes: 377eeaa8e1 ("x86/speculation/l1tf: Limit swap file size to MAX_PA/2")
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2207def700 upstream
nosmt on the kernel command line merely prevents the onlining of the
secondary SMT siblings.
nosmt=force makes the APIC detection code ignore the secondary SMT siblings
completely, so they even do not show up as possible CPUs. That reduces the
amount of memory allocations for per cpu variables and saves other
resources from being allocated too large.
This is not fully equivalent to disabling SMT in the BIOS because the low
level SMT enabling in the BIOS can result in partitioning of resources
between the siblings, which is not undone by just ignoring them. Some CPUs
can use the full resources when their sibling is not onlined, but this is
depending on the CPU family and model and it's not well documented whether
this applies to all partitioned resources. That means depending on the
workload disabling SMT in the BIOS might result in better performance.
Linus analysis of the Intel manual:
The intel optimization manual is not very clear on what the partitioning
rules are.
I find:
"In general, the buffers for staging instructions between major pipe
stages are partitioned. These buffers include µop queues after the
execution trace cache, the queues after the register rename stage, the
reorder buffer which stages instructions for retirement, and the load
and store buffers.
In the case of load and store buffers, partitioning also provided an
easier implementation to maintain memory ordering for each logical
processor and detect memory ordering violations"
but some of that partitioning may be relaxed if the HT thread is "not
active":
"In Intel microarchitecture code name Sandy Bridge, the micro-op queue
is statically partitioned to provide 28 entries for each logical
processor, irrespective of software executing in single thread or
multiple threads. If one logical processor is not active in Intel
microarchitecture code name Ivy Bridge, then a single thread executing
on that processor core can use the 56 entries in the micro-op queue"
but I do not know what "not active" means, and how dynamic it is. Some of
that partitioning may be entirely static and depend on the early BIOS
disabling of HT, and even if we park the cores, the resources will just be
wasted.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1e1d7e25fd upstream
To support force disabling of SMT it's required to know the number of
thread siblings early. amd_get_topology() cannot be called before the APIC
driver is selected, so split out the part which initializes
smp_num_siblings and invoke it from amd_early_init().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 119bff8a9c upstream
Old code used to check whether CPUID ext max level is >= 0x80000008 because
that last leaf contains the number of cores of the physical CPU. The three
functions called there now do not depend on that leaf anymore so the check
can go.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1910ad5624 upstream
Make use of the new early detection function to initialize smp_num_siblings
on the boot cpu before the MP-Table or ACPI/MADT scan happens. That's
required for force disabling SMT.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 95f3d39ccf upstream
To support force disabling of SMT it's required to know the number of
thread siblings early. detect_extended_topology() cannot be called before
the APIC driver is selected, so split out the part which initializes
smp_num_siblings.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 545401f444 upstream
To support force disabling of SMT it's required to know the number of
thread siblings early. detect_ht() cannot be called before the APIC driver
is selected, so split out the part which initializes smp_num_siblings.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 55e6d279ab upstream
The value of this printout is dubious at best and there is no point in
having it in two different places along with convoluted ways to reach it.
Remove it completely.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05736e4ac1 upstream
Provide a command line and a sysfs knob to control SMT.
The command line options are:
'nosmt': Enumerate secondary threads, but do not online them
'nosmt=force': Ignore secondary threads completely during enumeration
via MP table and ACPI/MADT.
The sysfs control file has the following states (read/write):
'on': SMT is enabled. Secondary threads can be freely onlined
'off': SMT is disabled. Secondary threads, even if enumerated
cannot be onlined
'forceoff': SMT is permanentely disabled. Writes to the control
file are rejected.
'notsupported': SMT is not supported by the CPU
The command line option 'nosmt' sets the sysfs control to 'off'. This
can be changed to 'on' to reenable SMT during runtime.
The command line option 'nosmt=force' sets the sysfs control to
'forceoff'. This cannot be changed during runtime.
When SMT is 'on' and the control file is changed to 'off' then all online
secondary threads are offlined and attempts to online a secondary thread
later on are rejected.
When SMT is 'off' and the control file is changed to 'on' then secondary
threads can be onlined again. The 'off' -> 'on' transition does not
automatically online the secondary threads.
When the control file is set to 'forceoff', the behaviour is the same as
setting it to 'off', but the operation is irreversible and later writes to
the control file are rejected.
When the control status is 'notsupported' then writes to the control file
are rejected.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc1fe215e1 upstream
Split out the inner workings of do_cpu_down() to allow reuse of that
function for the upcoming SMT disabling mechanism.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c4de65696d upstream
The asymmetry caused a warning to trigger if the bootup was stopped in state
CPUHP_AP_ONLINE_IDLE. The warning no longer triggers as kthread_park() can
now be invoked on already or still parked threads. But there is still no
reason to have this be asymmetric.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6a4d2657e0 upstream
If the CPU is supporting SMT then the primary thread can be found by
checking the lower APIC ID bits for zero. smp_num_siblings is used to build
the mask for the APIC ID bits which need to be taken into account.
This uses the MPTABLE or ACPI/MADT supplied APIC ID, which can be different
than the initial APIC ID in CPUID. But according to AMD the lower bits have
to be consistent. Intel gave a tentative confirmation as well.
Preparatory patch to support disabling SMT at boot/runtime.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ba2591a599 upstream
The static key sched_smt_present is only updated at boot time when SMT
siblings have been detected. Booting with maxcpus=1 and bringing the
siblings online after boot rebuilds the scheduling domains correctly but
does not update the static key, so the SMT code is not enabled.
Let the key be updated in the scheduler CPU hotplug code to fix this.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 56563f53d3 upstream
The pr_warn in l1tf_select_mitigation would have used the prior pr_fmt
which was defined as "Spectre V2 : ".
Move the function to be past SSBD and also define the pr_fmt.
Fixes: 17dbca1193 ("x86/speculation/l1tf: Add sysfs reporting for l1tf")
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 377eeaa8e1 upstream
For the L1TF workaround its necessary to limit the swap file size to below
MAX_PA/2, so that the higher bits of the swap offset inverted never point
to valid memory.
Add a mechanism for the architecture to override the swap file size check
in swapfile.c and add a x86 specific max swapfile check function that
enforces that limit.
The check is only enabled if the CPU is vulnerable to L1TF.
In VMs with 42bit MAX_PA the typical limit is 2TB now, on a native system
with 46bit PA it is 32TB. The limit is only per individual swap file, so
it's always possible to exceed these limits with multiple swap files or
partitions.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 42e4089c78 upstream
For L1TF PROT_NONE mappings are protected by inverting the PFN in the page
table entry. This sets the high bits in the CPU's address space, thus
making sure to point to not point an unmapped entry to valid cached memory.
Some server system BIOSes put the MMIO mappings high up in the physical
address space. If such an high mapping was mapped to unprivileged users
they could attack low memory by setting such a mapping to PROT_NONE. This
could happen through a special device driver which is not access
protected. Normal /dev/mem is of course access protected.
To avoid this forbid PROT_NONE mappings or mprotect for high MMIO mappings.
Valid page mappings are allowed because the system is then unsafe anyways.
It's not expected that users commonly use PROT_NONE on MMIO. But to
minimize any impact this is only enforced if the mapping actually refers to
a high MMIO address (defined as the MAX_PA-1 bit being set), and also skip
the check for root.
For mmaps this is straight forward and can be handled in vm_insert_pfn and
in remap_pfn_range().
For mprotect it's a bit trickier. At the point where the actual PTEs are
accessed a lot of state has been changed and it would be difficult to undo
on an error. Since this is a uncommon case use a separate early page talk
walk pass for MMIO PROT_NONE mappings that checks for this condition
early. For non MMIO and non PROT_NONE there are no changes.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 17dbca1193 upstream
L1TF core kernel workarounds are cheap and normally always enabled, However
they still should be reported in sysfs if the system is vulnerable or
mitigated. Add the necessary CPU feature/bug bits.
- Extend the existing checks for Meltdowns to determine if the system is
vulnerable. All CPUs which are not vulnerable to Meltdown are also not
vulnerable to L1TF
- Check for 32bit non PAE and emit a warning as there is no practical way
for mitigation due to the limited physical address bits
- If the system has more than MAX_PA/2 physical memory the invert page
workarounds don't protect the system against the L1TF attack anymore,
because an inverted physical address will also point to valid
memory. Print a warning in this case and report that the system is
vulnerable.
Add a function which returns the PFN limit for the L1TF mitigation, which
will be used in follow up patches for sanity and range checks.
[ tglx: Renamed the CPU feature bit to L1TF_PTEINV ]
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 10a70416e1 upstream
The L1TF workaround doesn't make any attempt to mitigate speculate accesses
to the first physical page for zeroed PTEs. Normally it only contains some
data from the early real mode BIOS.
It's not entirely clear that the first page is reserved in all
configurations, so add an extra reservation call to make sure it is really
reserved. In most configurations (e.g. with the standard reservations)
it's likely a nop.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b28baca9b upstream
When PTEs are set to PROT_NONE the kernel just clears the Present bit and
preserves the PFN, which creates attack surface for L1TF speculation
speculation attacks.
This is important inside guests, because L1TF speculation bypasses physical
page remapping. While the host has its own migitations preventing leaking
data from other VMs into the guest, this would still risk leaking the wrong
page inside the current guest.
This uses the same technique as Linus' swap entry patch: while an entry is
is in PROTNONE state invert the complete PFN part part of it. This ensures
that the the highest bit will point to non existing memory.
The invert is done by pte/pmd_modify and pfn/pmd/pud_pte for PROTNONE and
pte/pmd/pud_pfn undo it.
This assume that no code path touches the PFN part of a PTE directly
without using these primitives.
This doesn't handle the case that MMIO is on the top of the CPU physical
memory. If such an MMIO region was exposed by an unpriviledged driver for
mmap it would be possible to attack some real memory. However this
situation is all rather unlikely.
For 32bit non PAE the inversion is not done because there are really not
enough bits to protect anything.
Q: Why does the guest need to be protected when the HyperVisor already has
L1TF mitigations?
A: Here's an example:
Physical pages 1 2 get mapped into a guest as
GPA 1 -> PA 2
GPA 2 -> PA 1
through EPT.
The L1TF speculation ignores the EPT remapping.
Now the guest kernel maps GPA 1 to process A and GPA 2 to process B, and
they belong to different users and should be isolated.
A sets the GPA 1 PA 2 PTE to PROT_NONE to bypass the EPT remapping and
gets read access to the underlying physical page. Which in this case
points to PA 2, so it can read process B's data, if it happened to be in
L1, so isolation inside the guest is broken.
There's nothing the hypervisor can do about this. This mitigation has to
be done in the guest itself.
[ tglx: Massaged changelog ]
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f22b4cd45 upstream
With L1 terminal fault the CPU speculates into unmapped PTEs, and resulting
side effects allow to read the memory the PTE is pointing too, if its
values are still in the L1 cache.
For swapped out pages Linux uses unmapped PTEs and stores a swap entry into
them.
To protect against L1TF it must be ensured that the swap entry is not
pointing to valid memory, which requires setting higher bits (between bit
36 and bit 45) that are inside the CPUs physical address space, but outside
any real memory.
To do this invert the offset to make sure the higher bits are always set,
as long as the swap file is not too big.
Note there is no workaround for 32bit !PAE, or on systems which have more
than MAX_PA/2 worth of memory. The later case is very unlikely to happen on
real systems.
[AK: updated description and minor tweaks by. Split out from the original
patch ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Andi Kleen <ak@linux.intel.com>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bcd11afa7a upstream
If pages are swapped out, the swap entry is stored in the corresponding
PTE, which has the Present bit cleared. CPUs vulnerable to L1TF speculate
on PTE entries which have the present bit set and would treat the swap
entry as phsyical address (PFN). To mitigate that the upper bits of the PTE
must be set so the PTE points to non existent memory.
The swap entry stores the type and the offset of a swapped out page in the
PTE. type is stored in bit 9-13 and offset in bit 14-63. The hardware
ignores the bits beyond the phsyical address space limit, so to make the
mitigation effective its required to start 'offset' at the lowest possible
bit so that even large swap offsets do not reach into the physical address
space limit bits.
Move offset to bit 9-58 and type to bit 59-63 which are the bits that
hardware generally doesn't care about.
That, in turn, means that if you on desktop chip with only 40 bits of
physical addressing, now that the offset starts at bit 9, there needs to be
30 bits of offset actually *in use* until bit 39 ends up being set, which
means when inverted it will again point into existing memory.
So that's 4 terabyte of swap space (because the offset is counted in pages,
so 30 bits of offset is 42 bits of actual coverage). With bigger physical
addressing, that obviously grows further, until the limit of the offset is
hit (at 50 bits of offset - 62 bits of actual swap file coverage).
This is a preparatory change for the actual swap entry inversion to protect
against L1TF.
[ AK: Updated description and minor tweaks. Split into two parts ]
[ tglx: Massaged changelog ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Andi Kleen <ak@linux.intel.com>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 50896e180c upstream
L1 Terminal Fault (L1TF) is a speculation related vulnerability. The CPU
speculates on PTE entries which do not have the PRESENT bit set, if the
content of the resulting physical address is available in the L1D cache.
The OS side mitigation makes sure that a !PRESENT PTE entry points to a
physical address outside the actually existing and cachable memory
space. This is achieved by inverting the upper bits of the PTE. Due to the
address space limitations this only works for 64bit and 32bit PAE kernels,
but not for 32bit non PAE.
This mitigation applies to both host and guest kernels, but in case of a
64bit host (hypervisor) and a 32bit PAE guest, inverting the upper bits of
the PAE address space (44bit) is not enough if the host has more than 43
bits of populated memory address space, because the speculation treats the
PTE content as a physical host address bypassing EPT.
The host (hypervisor) protects itself against the guest by flushing L1D as
needed, but pages inside the guest are not protected against attacks from
other processes inside the same guest.
For the guest the inverted PTE mask has to match the host to provide the
full protection for all pages the host could possibly map into the
guest. The hosts populated address space is not known to the guest, so the
mask must cover the possible maximal host address space, i.e. 52 bit.
On 32bit PAE the maximum PTE mask is currently set to 44 bit because that
is the limit imposed by 32bit unsigned long PFNs in the VMs. This limits
the mask to be below what the host could possible use for physical pages.
The L1TF PROT_NONE protection code uses the PTE masks to determine which
bits to invert to make sure the higher bits are set for unmapped entries to
prevent L1TF speculation attacks against EPT inside guests.
In order to invert all bits that could be used by the host, increase
__PHYSICAL_PAGE_SHIFT to 52 to match 64bit.
The real limit for a 32bit PAE kernel is still 44 bits because all Linux
PTEs are created from unsigned long PFNs, so they cannot be higher than 44
bits on a 32bit kernel. So these extra PFN bits should be never set. The
only users of this macro are using it to look at PTEs, so it's safe.
[ tglx: Massaged changelog ]
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5800dc5c19 upstream.
Nadav reported that on guests we're failing to rewrite the indirect
calls to CALLEE_SAVE paravirt functions. In particular the
pv_queued_spin_unlock() call is left unpatched and that is all over the
place. This obviously wrecks Spectre-v2 mitigation (for paravirt
guests) which relies on not actually having indirect calls around.
The reason is an incorrect clobber test in paravirt_patch_call(); this
function rewrites an indirect call with a direct call to the _SAME_
function, there is no possible way the clobbers can be different
because of this.
Therefore remove this clobber check. Also put WARNs on the other patch
failure case (not enough room for the instruction) which I've not seen
trigger in my (limited) testing.
Three live kernel image disassemblies for lock_sock_nested (as a small
function that illustrates the problem nicely). PRE is the current
situation for guests, POST is with this patch applied and NATIVE is with
or without the patch for !guests.
PRE:
(gdb) disassemble lock_sock_nested
Dump of assembler code for function lock_sock_nested:
0xffffffff817be970 <+0>: push %rbp
0xffffffff817be971 <+1>: mov %rdi,%rbp
0xffffffff817be974 <+4>: push %rbx
0xffffffff817be975 <+5>: lea 0x88(%rbp),%rbx
0xffffffff817be97c <+12>: callq 0xffffffff819f7160 <_cond_resched>
0xffffffff817be981 <+17>: mov %rbx,%rdi
0xffffffff817be984 <+20>: callq 0xffffffff819fbb00 <_raw_spin_lock_bh>
0xffffffff817be989 <+25>: mov 0x8c(%rbp),%eax
0xffffffff817be98f <+31>: test %eax,%eax
0xffffffff817be991 <+33>: jne 0xffffffff817be9ba <lock_sock_nested+74>
0xffffffff817be993 <+35>: movl $0x1,0x8c(%rbp)
0xffffffff817be99d <+45>: mov %rbx,%rdi
0xffffffff817be9a0 <+48>: callq *0xffffffff822299e8
0xffffffff817be9a7 <+55>: pop %rbx
0xffffffff817be9a8 <+56>: pop %rbp
0xffffffff817be9a9 <+57>: mov $0x200,%esi
0xffffffff817be9ae <+62>: mov $0xffffffff817be993,%rdi
0xffffffff817be9b5 <+69>: jmpq 0xffffffff81063ae0 <__local_bh_enable_ip>
0xffffffff817be9ba <+74>: mov %rbp,%rdi
0xffffffff817be9bd <+77>: callq 0xffffffff817be8c0 <__lock_sock>
0xffffffff817be9c2 <+82>: jmp 0xffffffff817be993 <lock_sock_nested+35>
End of assembler dump.
POST:
(gdb) disassemble lock_sock_nested
Dump of assembler code for function lock_sock_nested:
0xffffffff817be970 <+0>: push %rbp
0xffffffff817be971 <+1>: mov %rdi,%rbp
0xffffffff817be974 <+4>: push %rbx
0xffffffff817be975 <+5>: lea 0x88(%rbp),%rbx
0xffffffff817be97c <+12>: callq 0xffffffff819f7160 <_cond_resched>
0xffffffff817be981 <+17>: mov %rbx,%rdi
0xffffffff817be984 <+20>: callq 0xffffffff819fbb00 <_raw_spin_lock_bh>
0xffffffff817be989 <+25>: mov 0x8c(%rbp),%eax
0xffffffff817be98f <+31>: test %eax,%eax
0xffffffff817be991 <+33>: jne 0xffffffff817be9ba <lock_sock_nested+74>
0xffffffff817be993 <+35>: movl $0x1,0x8c(%rbp)
0xffffffff817be99d <+45>: mov %rbx,%rdi
0xffffffff817be9a0 <+48>: callq 0xffffffff810a0c20 <__raw_callee_save___pv_queued_spin_unlock>
0xffffffff817be9a5 <+53>: xchg %ax,%ax
0xffffffff817be9a7 <+55>: pop %rbx
0xffffffff817be9a8 <+56>: pop %rbp
0xffffffff817be9a9 <+57>: mov $0x200,%esi
0xffffffff817be9ae <+62>: mov $0xffffffff817be993,%rdi
0xffffffff817be9b5 <+69>: jmpq 0xffffffff81063aa0 <__local_bh_enable_ip>
0xffffffff817be9ba <+74>: mov %rbp,%rdi
0xffffffff817be9bd <+77>: callq 0xffffffff817be8c0 <__lock_sock>
0xffffffff817be9c2 <+82>: jmp 0xffffffff817be993 <lock_sock_nested+35>
End of assembler dump.
NATIVE:
(gdb) disassemble lock_sock_nested
Dump of assembler code for function lock_sock_nested:
0xffffffff817be970 <+0>: push %rbp
0xffffffff817be971 <+1>: mov %rdi,%rbp
0xffffffff817be974 <+4>: push %rbx
0xffffffff817be975 <+5>: lea 0x88(%rbp),%rbx
0xffffffff817be97c <+12>: callq 0xffffffff819f7160 <_cond_resched>
0xffffffff817be981 <+17>: mov %rbx,%rdi
0xffffffff817be984 <+20>: callq 0xffffffff819fbb00 <_raw_spin_lock_bh>
0xffffffff817be989 <+25>: mov 0x8c(%rbp),%eax
0xffffffff817be98f <+31>: test %eax,%eax
0xffffffff817be991 <+33>: jne 0xffffffff817be9ba <lock_sock_nested+74>
0xffffffff817be993 <+35>: movl $0x1,0x8c(%rbp)
0xffffffff817be99d <+45>: mov %rbx,%rdi
0xffffffff817be9a0 <+48>: movb $0x0,(%rdi)
0xffffffff817be9a3 <+51>: nopl 0x0(%rax)
0xffffffff817be9a7 <+55>: pop %rbx
0xffffffff817be9a8 <+56>: pop %rbp
0xffffffff817be9a9 <+57>: mov $0x200,%esi
0xffffffff817be9ae <+62>: mov $0xffffffff817be993,%rdi
0xffffffff817be9b5 <+69>: jmpq 0xffffffff81063ae0 <__local_bh_enable_ip>
0xffffffff817be9ba <+74>: mov %rbp,%rdi
0xffffffff817be9bd <+77>: callq 0xffffffff817be8c0 <__lock_sock>
0xffffffff817be9c2 <+82>: jmp 0xffffffff817be993 <lock_sock_nested+35>
End of assembler dump.
Fixes: 63f70270cc ("[PATCH] i386: PARAVIRT: add common patching machinery")
Fixes: 3010a0663f ("x86/paravirt, objtool: Annotate indirect calls")
Reported-by: Nadav Amit <namit@vmware.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1bcfe05640 upstream.
Use the correct IRQ line for the MSI controller in the PCIe host
controller. Apparently a different IRQ line is used compared to other
i.MX6 variants. Without this change MSI IRQs aren't properly propagated
to the upstream interrupt controller.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Fixes: b1d17f68e5 ("ARM: dts: imx: add initial imx6sx device tree source")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 119e1ef80e upstream.
__legitimize_mnt() has two problems - one is that in case of success
the check of mount_lock is not ordered wrt preceding increment of
refcount, making it possible to have successful __legitimize_mnt()
on one CPU just before the otherwise final mntpu() on another,
with __legitimize_mnt() not seeing mntput() taking the lock and
mntput() not seeing the increment done by __legitimize_mnt().
Solved by a pair of barriers.
Another is that failure of __legitimize_mnt() on the second
read_seqretry() leaves us with reference that'll need to be
dropped by caller; however, if that races with final mntput()
we can end up with caller dropping rcu_read_lock() and doing
mntput() to release that reference - with the first mntput()
having freed the damn thing just as rcu_read_lock() had been
dropped. Solution: in "do mntput() yourself" failure case
grab mount_lock, check if MNT_DOOMED has been set by racing
final mntput() that has missed our increment and if it has -
undo the increment and treat that as "failure, caller doesn't
need to drop anything" case.
It's not easy to hit - the final mntput() has to come right
after the first read_seqretry() in __legitimize_mnt() *and*
manage to miss the increment done by __legitimize_mnt() before
the second read_seqretry() in there. The things that are almost
impossible to hit on bare hardware are not impossible on SMP
KVM, though...
Reported-by: Oleg Nesterov <oleg@redhat.com>
Fixes: 48a066e72d ("RCU'd vsfmounts")
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9ea0a46ca2 upstream.
mntput_no_expire() does the calculation of total refcount under mount_lock;
unfortunately, the decrement (as well as all increments) are done outside
of it, leading to false positives in the "are we dropping the last reference"
test. Consider the following situation:
* mnt is a lazy-umounted mount, kept alive by two opened files. One
of those files gets closed. Total refcount of mnt is 2. On CPU 42
mntput(mnt) (called from __fput()) drops one reference, decrementing component
* After it has looked at component #0, the process on CPU 0 does
mntget(), incrementing component #0, gets preempted and gets to run again -
on CPU 69. There it does mntput(), which drops the reference (component #69)
and proceeds to spin on mount_lock.
* On CPU 42 our first mntput() finishes counting. It observes the
decrement of component #69, but not the increment of component #0. As the
result, the total it gets is not 1 as it should've been - it's 0. At which
point we decide that vfsmount needs to be killed and proceed to free it and
shut the filesystem down. However, there's still another opened file
on that filesystem, with reference to (now freed) vfsmount, etc. and we are
screwed.
It's not a wide race, but it can be reproduced with artificial slowdown of
the mnt_get_count() loop, and it should be easier to hit on SMP KVM setups.
Fix consists of moving the refcount decrement under mount_lock; the tricky
part is that we want (and can) keep the fast case (i.e. mount that still
has non-NULL ->mnt_ns) entirely out of mount_lock. All places that zero
mnt->mnt_ns are dropping some reference to mnt and they call synchronize_rcu()
before that mntput(). IOW, if mntput() observes (under rcu_read_lock())
a non-NULL ->mnt_ns, it is guaranteed that there is another reference yet to
be dropped.
Reported-by: Jann Horn <jannh@google.com>
Tested-by: Jann Horn <jannh@google.com>
Fixes: 48a066e72d ("RCU'd vsfmounts")
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c0d7cd5c8 upstream.
RCU pathwalk relies upon the assumption that anything that changes
->d_inode of a dentry will invalidate its ->d_seq. That's almost
true - the one exception is that the final dput() of already unhashed
dentry does *not* touch ->d_seq at all. Unhashing does, though,
so for anything we'd found by RCU dcache lookup we are fine.
Unfortunately, we can *start* with an unhashed dentry or jump into
it.
We could try and be careful in the (few) places where that could
happen. Or we could just make the final dput() invalidate the damn
thing, unhashed or not. The latter is much simpler and easier to
backport, so let's do it that way.
Reported-by: "Dae R. Jeong" <threeearcat@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 90bad5e05b upstream.
Since mountpoint crossing can happen without leaving lazy mode,
root dentries do need the same protection against having their
memory freed without RCU delay as everything else in the tree.
It's partially hidden by RCU delay between detaching from the
mount tree and dropping the vfsmount reference, but the starting
point of pathwalk can be on an already detached mount, in which
case umount-caused RCU delay has already passed by the time the
lazy pathwalk grabs rcu_read_lock(). If the starting point
happens to be at the root of that vfsmount *and* that vfsmount
covers the entire filesystem, we get trouble.
Fixes: 48a066e72d ("RCU'd vsfmounts")
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5b1404d08 upstream.
This is purely a preparatory patch for upcoming changes during the 4.19
merge window.
We have a function called "boot_cpu_state_init()" that isn't really
about the bootup cpu state: that is done much earlier by the similarly
named "boot_cpu_init()" (note lack of "state" in name).
This function initializes some hotplug CPU state, and needs to run after
the percpu data has been properly initialized. It even has a comment to
that effect.
Except it _doesn't_ actually run after the percpu data has been properly
initialized. On x86 it happens to do that, but on at least arm and
arm64, the percpu base pointers are initialized by the arch-specific
'smp_prepare_boot_cpu()' hook, which ran _after_ boot_cpu_state_init().
This had some unexpected results, and in particular we have a patch
pending for the merge window that did the obvious cleanup of using
'this_cpu_write()' in the cpu hotplug init code:
- per_cpu_ptr(&cpuhp_state, smp_processor_id())->state = CPUHP_ONLINE;
+ this_cpu_write(cpuhp_state.state, CPUHP_ONLINE);
which is obviously the right thing to do. Except because of the
ordering issue, it actually failed miserably and unexpectedly on arm64.
So this just fixes the ordering, and changes the name of the function to
be 'boot_cpu_hotplug_init()' to make it obvious that it's about cpu
hotplug state, because the core CPU state was supposed to have already
been done earlier.
Marked for stable, since the (not yet merged) patch that will show this
problem is marked for stable.
Reported-by: Vlastimil Babka <vbabka@suse.cz>
Reported-by: Mian Yousaf Kaukab <yousaf.kaukab@suse.com>
Suggested-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1214fd7b49 upstream.
Surround scsi_execute() calls with scsi_autopm_get_device() and
scsi_autopm_put_device(). Note: removing sr_mutex protection from the
scsi_cd_get() and scsi_cd_put() calls is safe because the purpose of
sr_mutex is to serialize cdrom_*() calls.
This patch avoids that complaints similar to the following appear in the
kernel log if runtime power management is enabled:
INFO: task systemd-udevd:650 blocked for more than 120 seconds.
Not tainted 4.18.0-rc7-dbg+ #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
systemd-udevd D28176 650 513 0x00000104
Call Trace:
__schedule+0x444/0xfe0
schedule+0x4e/0xe0
schedule_preempt_disabled+0x18/0x30
__mutex_lock+0x41c/0xc70
mutex_lock_nested+0x1b/0x20
__blkdev_get+0x106/0x970
blkdev_get+0x22c/0x5a0
blkdev_open+0xe9/0x100
do_dentry_open.isra.19+0x33e/0x570
vfs_open+0x7c/0xd0
path_openat+0x6e3/0x1120
do_filp_open+0x11c/0x1c0
do_sys_open+0x208/0x2d0
__x64_sys_openat+0x59/0x70
do_syscall_64+0x77/0x230
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Maurizio Lombardi <mlombard@redhat.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <stable@vger.kernel.org>
Tested-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5121700b34 upstream.
While working on bpf_tcp_sendmsg() code, I noticed that when a
sk->sk_err is set we error out with err = sk->sk_err. However
this is problematic since sk->sk_err is a positive error value
and therefore we will neither go into sk_stream_error() nor will
we report an error back to user space. I had this case with EPIPE
and user space was thinking sendmsg() succeeded since EPIPE is
a positive value, thinking we submitted 32 bytes. Fix it by
negating the sk->sk_err value.
Fixes: 4f738adba3 ("bpf: create tcp_bpf_ulp allowing BPF to monitor socket TX/RX data")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c81c71730 upstream.
In bpf_tcp_sendmsg() the sk_alloc_sg() may fail. In the case of
ENOMEM, it may also mean that we've partially filled the scatterlist
entries with pages. Later jumping to sk_stream_wait_memory()
we could further fail with an error for several reasons, however
we miss to call free_start_sg() if the local sk_msg_buff was used.
Fixes: 4f738adba3 ("bpf: create tcp_bpf_ulp allowing BPF to monitor socket TX/RX data")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f7a7beaee upstream.
If zram supports writeback feature, it's no longer a
BD_CAP_SYNCHRONOUS_IO device beause zram does asynchronous IO operations
for incompressible pages.
Do not pretend to be synchronous IO device. It makes the system very
sluggish due to waiting for IO completion from upper layers.
Furthermore, it causes a user-after-free problem because swap thinks the
opearion is done when the IO functions returns so it can free the page
(e.g., lock_page_or_retry and goto out_release in do_swap_page) but in
fact, IO is asynchronous so the driver could access a just freed page
afterward.
This patch fixes the problem.
BUG: Bad page state in process qemu-system-x86 pfn:3dfab21
page:ffffdfb137eac840 count:0 mapcount:0 mapping:0000000000000000 index:0x1
flags: 0x17fffc000000008(uptodate)
raw: 017fffc000000008 dead000000000100 dead000000000200 0000000000000000
raw: 0000000000000001 0000000000000000 00000000ffffffff 0000000000000000
page dumped because: PAGE_FLAGS_CHECK_AT_PREP flag set
bad because of flags: 0x8(uptodate)
CPU: 4 PID: 1039 Comm: qemu-system-x86 Tainted: G B 4.18.0-rc5+ #1
Hardware name: Supermicro Super Server/X10SRL-F, BIOS 2.0b 05/02/2017
Call Trace:
dump_stack+0x5c/0x7b
bad_page+0xba/0x120
get_page_from_freelist+0x1016/0x1250
__alloc_pages_nodemask+0xfa/0x250
alloc_pages_vma+0x7c/0x1c0
do_swap_page+0x347/0x920
__handle_mm_fault+0x7b4/0x1110
handle_mm_fault+0xfc/0x1f0
__get_user_pages+0x12f/0x690
get_user_pages_unlocked+0x148/0x1f0
__gfn_to_pfn_memslot+0xff/0x3c0 [kvm]
try_async_pf+0x87/0x230 [kvm]
tdp_page_fault+0x132/0x290 [kvm]
kvm_mmu_page_fault+0x74/0x570 [kvm]
kvm_arch_vcpu_ioctl_run+0x9b3/0x1990 [kvm]
kvm_vcpu_ioctl+0x388/0x5d0 [kvm]
do_vfs_ioctl+0xa2/0x630
ksys_ioctl+0x70/0x80
__x64_sys_ioctl+0x16/0x20
do_syscall_64+0x55/0x100
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Link: https://lore.kernel.org/lkml/0516ae2d-b0fd-92c5-aa92-112ba7bd32fc@contabo.de/
Link: http://lkml.kernel.org/r/20180802051112.86174-1-minchan@kernel.org
[minchan@kernel.org: fix changelog, add comment]
Link: https://lore.kernel.org/lkml/0516ae2d-b0fd-92c5-aa92-112ba7bd32fc@contabo.de/
Link: http://lkml.kernel.org/r/20180802051112.86174-1-minchan@kernel.org
Link: http://lkml.kernel.org/r/20180805233722.217347-1-minchan@kernel.org
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Minchan Kim <minchan@kernel.org>
Reported-by: Tino Lehnig <tino.lehnig@contabo.de>
Tested-by: Tino Lehnig <tino.lehnig@contabo.de>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: <stable@vger.kernel.org> [4.15+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2610e88946 upstream.
This commit:
9fb8d5dc4b ("stop_machine, Disable preemption when waking two stopper threads")
does not fully address the race condition that can occur
as follows:
On one CPU, call it CPU 3, thread 1 invokes
cpu_stop_queue_two_works(2, 3,...), and the execution is such
that thread 1 queues the works for migration/2 and migration/3,
and is preempted after releasing the locks for migration/2 and
migration/3, but before waking the threads.
Then, On CPU 2, a kworker, call it thread 2, is running,
and it invokes cpu_stop_queue_two_works(1, 2,...), such that
thread 2 queues the works for migration/1 and migration/2.
Meanwhile, on CPU 3, thread 1 resumes execution, and wakes
migration/2 and migration/3. This means that when CPU 2
releases the locks for migration/1 and migration/2, but before
it wakes those threads, it can be preempted by migration/2.
If thread 2 is preempted by migration/2, then migration/2 will
execute the first work item successfully, since migration/3
was woken up by CPU 3, but when it goes to execute the second
work item, it disables preemption, calls multi_cpu_stop(),
and thus, CPU 2 will wait forever for migration/1, which should
have been woken up by thread 2. However migration/1 cannot be
woken up by thread 2, since it is a kworker, so it is affine to
CPU 2, but CPU 2 is running migration/2 with preemption
disabled, so thread 2 will never run.
Disable preemption after queueing works for stopper threads
to ensure that the operation of queueing the works and waking
the stopper threads is atomic.
Co-Developed-by: Prasad Sodagudi <psodagud@codeaurora.org>
Co-Developed-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Isaac J. Manjarres <isaacm@codeaurora.org>
Signed-off-by: Prasad Sodagudi <psodagud@codeaurora.org>
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: bigeasy@linutronix.de
Cc: gregkh@linuxfoundation.org
Cc: matt@codeblueprint.co.uk
Fixes: 9fb8d5dc4b ("stop_machine, Disable preemption when waking two stopper threads")
Link: http://lkml.kernel.org/r/1531856129-9871-1-git-send-email-isaacm@codeaurora.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c53776e29 upstream.
Way back in 4.9, we committed 4cd13c21b2 ("softirq: Let ksoftirqd do
its job"), and ever since we've had small nagging issues with it. For
example, we've had:
1ff688209e ("watchdog: core: make sure the watchdog_worker is not deferred")
8d5755b3f7 ("watchdog: softdog: fire watchdog even if softirqs do not get to run")
217f697436 ("net: busy-poll: allow preemption in sk_busy_loop()")
all of which worked around some of the effects of that commit.
The DVB people have also complained that the commit causes excessive USB
URB latencies, which seems to be due to the USB code using tasklets to
schedule USB traffic. This seems to be an issue mainly when already
living on the edge, but waiting for ksoftirqd to handle it really does
seem to cause excessive latencies.
Now Hanna Hawa reports that this issue isn't just limited to USB URB and
DVB, but also causes timeout problems for the Marvell SoC team:
"I'm facing kernel panic issue while running raid 5 on sata disks
connected to Macchiatobin (Marvell community board with Armada-8040
SoC with 4 ARMv8 cores of CA72) Raid 5 built with Marvell DMA engine
and async_tx mechanism (ASYNC_TX_DMA [=y]); the DMA driver (mv_xor_v2)
uses a tasklet to clean the done descriptors from the queue"
The latency problem causes a panic:
mv_xor_v2 f0400000.xor: dma_sync_wait: timeout!
Kernel panic - not syncing: async_tx_quiesce: DMA error waiting for transaction
We've discussed simply just reverting the original commit entirely, and
also much more involved solutions (with per-softirq threads etc). This
patch is intentionally stupid and fairly limited, because the issue
still remains, and the other solutions either got sidetracked or had
other issues.
We should probably also consider the timer softirqs to be synchronous
and not be delayed to ksoftirqd (since they were the issue with the
earlier watchdog problems), but that should be done as a separate patch.
This does only the tasklet cases.
Reported-and-tested-by: Hanna Hawa <hannah@marvell.com>
Reported-and-tested-by: Josef Griebichler <griebichler.josef@gmx.at>
Reported-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fedb8da963 upstream.
For years I thought all parisc machines executed loads and stores in
order. However, Jeff Law recently indicated on gcc-patches that this is
not correct. There are various degrees of out-of-order execution all the
way back to the PA7xxx processor series (hit-under-miss). The PA8xxx
series has full out-of-order execution for both integer operations, and
loads and stores.
This is described in the following article:
http://web.archive.org/web/20040214092531/http://www.cpus.hp.com/technical_references/advperf.shtml
For this reason, we need to define mb() and to insert a memory barrier
before the store unlocking spinlocks. This ensures that all memory
accesses are complete prior to unlocking. The ldcw instruction performs
the same function on entry.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org # 4.0+
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66509a276c upstream.
Enable the -mlong-calls compiler option by default, because otherwise in most
cases linking the vmlinux binary fails due to truncations of R_PARISC_PCREL22F
relocations. This fixes building the 64-bit defconfig.
Cc: stable@vger.kernel.org # 4.0+
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit afca6c5b25 upstream.
A recent fuzzed filesystem image cached random dcache corruption
when the reproducer was run. This often showed up as panics in
lookup_slow() on a null inode->i_ops pointer when doing pathwalks.
BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
....
Call Trace:
lookup_slow+0x44/0x60
walk_component+0x3dd/0x9f0
link_path_walk+0x4a7/0x830
path_lookupat+0xc1/0x470
filename_lookup+0x129/0x270
user_path_at_empty+0x36/0x40
path_listxattr+0x98/0x110
SyS_listxattr+0x13/0x20
do_syscall_64+0xf5/0x280
entry_SYSCALL_64_after_hwframe+0x42/0xb7
but had many different failure modes including deadlocks trying to
lock the inode that was just allocated or KASAN reports of
use-after-free violations.
The cause of the problem was a corrupt INOBT on a v4 fs where the
root inode was marked as free in the inobt record. Hence when we
allocated an inode, it chose the root inode to allocate, found it in
the cache and re-initialised it.
We recently fixed a similar inode allocation issue caused by inobt
record corruption problem in xfs_iget_cache_miss() in commit
ee457001ed ("xfs: catch inode allocation state mismatch
corruption"). This change adds similar checks to the cache-hit path
to catch it, and turns the reproducer into a corruption shutdown
situation.
Reported-by: Wen Xu <wen.xu@gatech.edu>
Signed-Off-By: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
[darrick: fix typos in comment]
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Cc: Eduardo Valentin <eduval@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb3d48dcf8 upstream.
xfs_attr3_leaf_create may have errored out before instantiating a buffer,
for example if the blkno is out of range. In that case there is no work
to do to remove it, and in fact xfs_da_shrink_inode will lead to an oops
if we try.
This also seems to fix a flaw where the original error from
xfs_attr3_leaf_create gets overwritten in the cleanup case, and it
removes a pointless assignment to bp which isn't used after this.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=199969
Reported-by: Xu, Wen <wen.xu@gatech.edu>
Tested-by: Xu, Wen <wen.xu@gatech.edu>
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Cc: Eduardo Valentin <eduval@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a32e236eb9 upstream.
It turns out that commit 721c7fc701 ("block: fail op_is_write()
requests to read-only partitions"), while obviously correct, causes
problems for some older lvm2 installations.
The reason is that the lvm snapshotting will continue to write to the
snapshow COW volume, even after the volume has been marked read-only.
End result: snapshot failure.
This has actually been fixed in newer version of the lvm2 tool, but the
old tools still exist, and the breakage was reported both in the kernel
bugzilla and in the Debian bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=200439https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=900442
The lvm2 fix is here
https://sourceware.org/git/?p=lvm2.git;a=commit;h=a6fdb9d9d70f51c49ad11a87ab4243344e6701a3
but until everybody has updated to recent versions, we'll have to weaken
the "never write to read-only partitions" check. It now allows the
write to happen, but causes a warning, something like this:
generic_make_request: Trying to write to read-only block-device dm-3 (partno X)
Modules linked in: nf_tables xt_cgroup xt_owner kvm_intel iwlmvm kvm irqbypass iwlwifi
CPU: 1 PID: 77 Comm: kworker/1:1 Not tainted 4.17.9-gentoo #3
Hardware name: LENOVO 20B6A019RT/20B6A019RT, BIOS GJET91WW (2.41 ) 09/21/2016
Workqueue: ksnaphd do_metadata
RIP: 0010:generic_make_request_checks+0x4ac/0x600
...
Call Trace:
generic_make_request+0x64/0x400
submit_bio+0x6c/0x140
dispatch_io+0x287/0x430
sync_io+0xc3/0x120
dm_io+0x1f8/0x220
do_metadata+0x1d/0x30
process_one_work+0x1b9/0x3e0
worker_thread+0x2b/0x3c0
kthread+0x113/0x130
ret_from_fork+0x35/0x40
Note that this is a "revert" in behavior only. I'm leaving alone the
actual code cleanups in commit 721c7fc701, but letting the previously
uncaught request go through with a warning instead of stopping it.
Fixes: 721c7fc701 ("block: fail op_is_write() requests to read-only partitions")
Reported-and-tested-by: WGH <wgh@torlan.ru>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Ilya Dryomov <idryomov@gmail.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Zdenek Kabelac <zkabelac@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd3599a0e1 upstream.
When we clone a range into a file we can end up dropping existing
extent maps (or trimming them) and replacing them with new ones if the
range to be cloned overlaps with a range in the destination inode.
When that happens we add the new extent maps to the list of modified
extents in the inode's extent map tree, so that a "fast" fsync (the flag
BTRFS_INODE_NEEDS_FULL_SYNC not set in the inode) will see the extent maps
and log corresponding extent items. However, at the end of range cloning
operation we do truncate all the pages in the affected range (in order to
ensure future reads will not get stale data). Sometimes this truncation
will release the corresponding extent maps besides the pages from the page
cache. If this happens, then a "fast" fsync operation will miss logging
some extent items, because it relies exclusively on the extent maps being
present in the inode's extent tree, leading to data loss/corruption if
the fsync ends up using the same transaction used by the clone operation
(that transaction was not committed in the meanwhile). An extent map is
released through the callback btrfs_invalidatepage(), which gets called by
truncate_inode_pages_range(), and it calls __btrfs_releasepage(). The
later ends up calling try_release_extent_mapping() which will release the
extent map if some conditions are met, like the file size being greater
than 16Mb, gfp flags allow blocking and the range not being locked (which
is the case during the clone operation) nor being the extent map flagged
as pinned (also the case for cloning).
The following example, turned into a test for fstests, reproduces the
issue:
$ mkfs.btrfs -f /dev/sdb
$ mount /dev/sdb /mnt
$ xfs_io -f -c "pwrite -S 0x18 9000K 6908K" /mnt/foo
$ xfs_io -f -c "pwrite -S 0x20 2572K 156K" /mnt/bar
$ xfs_io -c "fsync" /mnt/bar
# reflink destination offset corresponds to the size of file bar,
# 2728Kb minus 4Kb.
$ xfs_io -c ""reflink ${SCRATCH_MNT}/foo 0 2724K 15908K" /mnt/bar
$ xfs_io -c "fsync" /mnt/bar
$ md5sum /mnt/bar
95a95813a8c2abc9aa75a6c2914a077e /mnt/bar
<power fail>
$ mount /dev/sdb /mnt
$ md5sum /mnt/bar
207fd8d0b161be8a84b945f0df8d5f8d /mnt/bar
# digest should be 95a95813a8c2abc9aa75a6c2914a077e like before the
# power failure
In the above example, the destination offset of the clone operation
corresponds to the size of the "bar" file minus 4Kb. So during the clone
operation, the extent map covering the range from 2572Kb to 2728Kb gets
trimmed so that it ends at offset 2724Kb, and a new extent map covering
the range from 2724Kb to 11724Kb is created. So at the end of the clone
operation when we ask to truncate the pages in the range from 2724Kb to
2724Kb + 15908Kb, the page invalidation callback ends up removing the new
extent map (through try_release_extent_mapping()) when the page at offset
2724Kb is passed to that callback.
Fix this by setting the bit BTRFS_INODE_NEEDS_FULL_SYNC whenever an extent
map is removed at try_release_extent_mapping(), forcing the next fsync to
search for modified extents in the fs/subvolume tree instead of relying on
the presence of extent maps in memory. This way we can continue doing a
"fast" fsync if the destination range of a clone operation does not
overlap with an existing range or if any of the criteria necessary to
remove an extent map at try_release_extent_mapping() is not met (file
size not bigger then 16Mb or gfp flags do not allow blocking).
CC: stable@vger.kernel.org # 3.16+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 73c8d89455 upstream.
Maintain the tracing on/off setting of the ring_buffer when switching
to the trace buffer snapshot.
Taking a snapshot is done by swapping the backup ring buffer
(max_tr_buffer). But since the tracing on/off setting is defined
by the ring buffer, when swapping it, the tracing on/off setting
can also be changed. This causes a strange result like below:
/sys/kernel/debug/tracing # cat tracing_on
1
/sys/kernel/debug/tracing # echo 0 > tracing_on
/sys/kernel/debug/tracing # cat tracing_on
0
/sys/kernel/debug/tracing # echo 1 > snapshot
/sys/kernel/debug/tracing # cat tracing_on
1
/sys/kernel/debug/tracing # echo 1 > snapshot
/sys/kernel/debug/tracing # cat tracing_on
0
We don't touch tracing_on, but snapshot changes tracing_on
setting each time. This is an anomaly, because user doesn't know
that each "ring_buffer" stores its own tracing-enable state and
the snapshot is done by swapping ring buffers.
Link: http://lkml.kernel.org/r/153149929558.11274.11730609978254724394.stgit@devbox
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Tom Zanussi <tom.zanussi@linux.intel.com>
Cc: Hiraku Toyooka <hiraku.toyooka@cybertrust.co.jp>
Cc: stable@vger.kernel.org
Fixes: debdd57f51 ("tracing: Make a snapshot feature available from userspace")
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
[ Updated commit log and comment in the code ]
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0a0e0829f9 upstream.
The full nohz tick is reprogrammed in irq_exit() only if the exit is not in
a nesting interrupt. This stands as an optimization: whether a hardirq or a
softirq is interrupted, the tick is going to be reprogrammed when necessary
at the end of the inner interrupt, with even potential new updates on the
timer queue.
When soft interrupts are interrupted, it's assumed that they are executing
on the tail of an interrupt return. In that case tick_nohz_irq_exit() is
called after softirq processing to take care of the tick reprogramming.
But the assumption is wrong: softirqs can be processed inline as well, ie:
outside of an interrupt, like in a call to local_bh_enable() or from
ksoftirqd.
Inline softirqs don't reprogram the tick once they are done, as opposed to
interrupt tail softirq processing. So if a tick interrupts an inline
softirq processing, the next timer will neither be reprogrammed from the
interrupting tick's irq_exit() nor after the interrupted softirq
processing. This situation may leave the tick unprogrammed while timers are
armed.
To fix this, simply keep reprogramming the tick even if a softirq has been
interrupted. That can be optimized further, but for now correctness is more
important.
Note that new timers enqueued in nohz_full mode after a softirq gets
interrupted will still be handled just fine through self-IPIs triggered by
the timer code.
Reported-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Cc: stable@vger.kernel.org # 4.14+
Link: https://lkml.kernel.org/r/1533303094-15855-1-git-send-email-frederic@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 156c8b58ef upstream.
Masayoshi Mizuma reported that a warning message is shown while a CPU is
hot-removed on Broadwell servers:
WARNING: CPU: 126 PID: 6 at arch/x86/events/intel/uncore.c:988
uncore_pci_remove+0x10b/0x150
Call Trace:
pci_device_remove+0x42/0xd0
device_release_driver_internal+0x148/0x220
pci_stop_bus_device+0x76/0xa0
pci_stop_root_bus+0x44/0x60
acpi_pci_root_remove+0x1f/0x80
acpi_bus_trim+0x57/0x90
acpi_bus_trim+0x2e/0x90
acpi_device_hotplug+0x2bc/0x4b0
acpi_hotplug_work_fn+0x1a/0x30
process_one_work+0x174/0x3a0
worker_thread+0x4c/0x3d0
kthread+0xf8/0x130
This bug was introduced by:
commit 15a3e845b0 ("perf/x86/intel/uncore: Fix SBOX support for Broadwell CPUs")
The index of "QPI Port 2 filter" was hardcode to 2, but this conflicts with the
index of "PCU.3" which is "HSWEP_PCI_PCU_3", which equals to 2 as well.
To fix the conflict, the hardcoded index needs to be cleaned up:
- introduce a new enumerator "BDX_PCI_QPI_PORT2_FILTER" for "QPI Port 2
filter" on Broadwell,
- increase UNCORE_EXTRA_PCI_DEV_MAX by one,
- clean up the hardcoded index.
Debugged-by: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Suggested-by: Ingo Molnar <mingo@kernel.org>
Reported-by: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Tested-by: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: msys.mizuma@gmail.com
Cc: stable@vger.kernel.org
Fixes: 15a3e845b0 ("perf/x86/intel/uncore: Fix SBOX support for Broadwell CPUs")
Link: http://lkml.kernel.org/r/1532953688-15008-1-git-send-email-kan.liang@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d1f0301b33 upstream.
The support of force threading interrupts which are set up with both a
primary and a threaded handler wreckaged the setup of regular requested
threaded interrupts (primary handler == NULL).
The reason is that it does not check whether the primary handler is set to
the default handler which wakes the handler thread. Instead it replaces the
thread handler with the primary handler as it would do with force threaded
interrupts which have been requested via request_irq(). So both the primary
and the thread handler become the same which then triggers the warnon that
the thread handler tries to wakeup a not configured secondary thread.
Fortunately this only happens when the driver omits the IRQF_ONESHOT flag
when requesting the threaded interrupt, which is normaly caught by the
sanity checks when force irq threading is disabled.
Fix it by skipping the force threading setup when a regular threaded
interrupt is requested. As a consequence the interrupt request which lacks
the IRQ_ONESHOT flag is rejected correctly instead of silently wreckaging
it.
Fixes: 2a1d3ab898 ("genirq: Handle force threading of irqs with primary and thread handler")
Reported-by: Kurt Kanzenbach <kurt.kanzenbach@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Kurt Kanzenbach <kurt.kanzenbach@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 961b33c244 upstream.
Bart Massey reported what turned out to be a usercopy whitelist false
positive in JFS when symlink contents exceeded 128 bytes. The inline
inode data (i_inline) is actually designed to overflow into the "extended
area" following it (i_inline_ea) when needed. So the whitelist needed to
be expanded to include both i_inline and i_inline_ea (the whole size
of which is calculated internally using IDATASIZE, 256, instead of
sizeof(i_inline), 128).
$ cd /mnt/jfs
$ touch $(perl -e 'print "B" x 250')
$ ln -s B* b
$ ls -l >/dev/null
[ 249.436410] Bad or missing usercopy whitelist? Kernel memory exposure attempt detected from SLUB object 'jfs_ip' (offset 616, size 250)!
Reported-by: Bart Massey <bart.massey@gmail.com>
Fixes: 8d2704d382 ("jfs: Define usercopy region in jfs_ip slab cache")
Cc: Dave Kleikamp <shaggy@kernel.org>
Cc: jfs-discussion@lists.sourceforge.net
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b08abbd9f5 upstream.
During unload process, the chip can encounter problem where a FW dump would
be captured. For this case, the full reset sequence will be skip to bring
the chip back to full operational state.
Fixes: e315cd28b9 ("[SCSI] qla2xxx: Code changes for qla data structure refactoring")
Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e3dde080eb upstream.
In case of IOCB Queue full or system where memory is low and driver
receives large number of RSCN storm, the stale sp pointer can stay on
gpnid_list resulting in page_fault.
This patch fixes this issue by initializing the sp->elem list head and
removing sp->elem before memory is freed.
Following stack trace is seen
9 [ffff987b37d1bc60] page_fault at ffffffffad516768 [exception RIP: qla24xx_async_gpnid+496]
10 [ffff987b37d1bd10] qla24xx_async_gpnid at ffffffffc039866d [qla2xxx]
11 [ffff987b37d1bd80] qla2x00_do_work at ffffffffc036169c [qla2xxx]
12 [ffff987b37d1be38] qla2x00_do_dpc_all_vps at ffffffffc03adfed [qla2xxx]
13 [ffff987b37d1be78] qla2x00_do_dpc at ffffffffc036458a [qla2xxx]
14 [ffff987b37d1bec8] kthread at ffffffffacebae31
Fixes: 2d73ac6102 ("scsi: qla2xxx: Serialize GPNID for multiple RSCN")
Cc: <stable@vger.kernel.org> # v4.17+
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46d8c4b286 upstream.
This was detected by the self-test thanks to Ard's chunking patch.
I finally got around to testing this out on my ancient Via box. It
turns out that the workaround got the assembly wrong and we end up
doing count + initial cycles of the loop instead of just count.
This obviously causes corruption, either by overwriting the source
that is yet to be processed, or writing over the end of the buffer.
On CPUs that don't require the workaround only ECB is affected.
On Nano CPUs both ECB and CBC are affected.
This patch fixes it by doing the subtraction prior to the assembly.
Fixes: a76c1c23d0 ("crypto: padlock-aes - work around Nano CPU...")
Cc: <stable@vger.kernel.org>
Reported-by: Jamie Heilman <jamie@audible.transient.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit addb8a6559 upstream.
The commit cited below checked that the port numbers provided in the
primary and alt AVs are legal.
That is sufficient to prevent a kernel panic. However, it is not
sufficient for correct operation.
In Linux, AVs (both primary and alt) must be completely self-described.
We do not accept an AV from userspace without an embedded port number.
(This has been the case since kernel 3.14 commit dbf727de74
("IB/core: Use GID table in AH creation and dmac resolution")).
For the primary AV, this embedded port number must match the port number
specified with IB_QP_PORT.
We also expect the port number embedded in the alt AV to match the
alt_port_num value passed by the userspace driver in the modify_qp command
base structure.
Add these checks to modify_qp.
Cc: <stable@vger.kernel.org> # 4.16
Fixes: 5d4c05c3ee ("RDMA/uverbs: Sanitize user entered port numbers prior to access it")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 299b6365a3 upstream.
NVRAM is designed to work with Broadcom's SDK Linux kernel which fakes
PCI domain 0 for all internal MMIO devices. Since official Linux kernel
uses platform devices for that purpose there is a mismatch in numbering
PCI domains.
There used to be a fix for that problem but it was accidentally dropped
during the last firmware loading rework. That resulted in brcmfmac not
being able to extract device specific NVRAM content and all kind of
calibration problems.
Reported-by: Aditya Xavier <adityaxavier@gmail.com>
Fixes: 2baa3aaee2 ("brcmfmac: introduce brcmf_fw_alloc_request() function")
Cc: stable@vger.kernel.org # v4.17+
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eec3636ad1 upstream.
Commit 05ea88608d ("mm, hugetlbfs: introduce ->pagesize() to
vm_operations_struct") adds a new ->pagesize() function to
hugetlb_vm_ops, intended to cover all hugetlbfs backed files.
With System V shared memory model, if "huge page" is specified, the
"shared memory" is backed by hugetlbfs files, but the mappings initiated
via shmget/shmat have their original vm_ops overwritten with shm_vm_ops,
so we need to add a ->pagesize function to shm_vm_ops. Otherwise,
vma_kernel_pagesize() returns PAGE_SIZE given a hugetlbfs backed vma,
result in below BUG:
fs/hugetlbfs/inode.c
443 if (unlikely(page_mapped(page))) {
444 BUG_ON(truncate_op);
resulting in
hugetlbfs: oracle (4592): Using mlock ulimits for SHM_HUGETLB is deprecated
------------[ cut here ]------------
kernel BUG at fs/hugetlbfs/inode.c:444!
Modules linked in: nfsv3 rpcsec_gss_krb5 nfsv4 ...
CPU: 35 PID: 5583 Comm: oracle_5583_sbt Not tainted 4.14.35-1829.el7uek.x86_64 #2
RIP: 0010:remove_inode_hugepages+0x3db/0x3e2
....
Call Trace:
hugetlbfs_evict_inode+0x1e/0x3e
evict+0xdb/0x1af
iput+0x1a2/0x1f7
dentry_unlink_inode+0xc6/0xf0
__dentry_kill+0xd8/0x18d
dput+0x1b5/0x1ed
__fput+0x18b/0x216
____fput+0xe/0x10
task_work_run+0x90/0xa7
exit_to_usermode_loop+0xdd/0x116
do_syscall_64+0x187/0x1ae
entry_SYSCALL_64_after_hwframe+0x150/0x0
[jane.chu@oracle.com: relocate comment]
Link: http://lkml.kernel.org/r/20180731044831.26036-1-jane.chu@oracle.com
Link: http://lkml.kernel.org/r/20180727211727.5020-1-jane.chu@oracle.com
Fixes: 05ea88608d ("mm, hugetlbfs: introduce ->pagesize() to vm_operations_struct")
Signed-off-by: Jane Chu <jane.chu@oracle.com>
Suggested-by: Mike Kravetz <mike.kravetz@oracle.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Acked-by: Davidlohr Bueso <dave@stgolabs.net>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Jérôme Glisse <jglisse@redhat.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b305f7ed0f upstream.
The variable 'context->module.name' may be null pointer when
kmalloc return null, so it's better to check it before using
to avoid null dereference.
Another one more thing this patch does is using kstrdup instead
of (kmalloc + strcpy), and signal a lost record via audit_log_lost.
Cc: stable@vger.kernel.org # 4.11
Signed-off-by: Yi Wang <wang.yi59@zte.com.cn>
Reviewed-by: Jiang Biao <jiang.biao2@zte.com.cn>
Reviewed-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 63aff65573 upstream.
VPID for the nested vcpu is allocated at vmx_create_vcpu whenever nested
vmx is turned on with the module parameter.
However, it's only freed if the L1 guest has executed VMXON which is not
a given.
As a result, on a system with nested==on every creation+deletion of an
L1 vcpu without running an L2 guest results in leaking one vpid. Since
the total number of vpids is limited to 64k, they can eventually get
exhausted, preventing L2 from starting.
Delay allocation of the L2 vpid until VMXON emulation, thus matching its
freeing.
Fixes: 5c614b3583
Cc: stable@vger.kernel.org
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b3681dd548 upstream.
error_entry and error_exit communicate the user vs. kernel status of
the frame using %ebx. This is unnecessary -- the information is in
regs->cs. Just use regs->cs.
This makes error_entry simpler and makes error_exit more robust.
It also fixes a nasty bug. Before all the Spectre nonsense, the
xen_failsafe_callback entry point returned like this:
ALLOC_PT_GPREGS_ON_STACK
SAVE_C_REGS
SAVE_EXTRA_REGS
ENCODE_FRAME_POINTER
jmp error_exit
And it did not go through error_entry. This was bogus: RBX
contained garbage, and error_exit expected a flag in RBX.
Fortunately, it generally contained *nonzero* garbage, so the
correct code path was used. As part of the Spectre fixes, code was
added to clear RBX to mitigate certain speculation attacks. Now,
depending on kernel configuration, RBX got zeroed and, when running
some Wine workloads, the kernel crashes. This was introduced by:
commit 3ac6d8c787 ("x86/entry/64: Clear registers for exceptions/interrupts, to reduce speculation attack surface")
With this patch applied, RBX is no longer needed as a flag, and the
problem goes away.
I suspect that malicious userspace could use this bug to crash the
kernel even without the offending patch applied, though.
[ Historical note: I wrote this patch as a cleanup before I was aware
of the bug it fixed. ]
[ Note to stable maintainers: this should probably get applied to all
kernels. If you're nervous about that, a more conservative fix to
add xorl %ebx,%ebx; incl %ebx before the jump to error_exit should
also fix the problem. ]
Reported-and-tested-by: M. Vefa Bicakci <m.v.b@runbox.com>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Cc: xen-devel@lists.xenproject.org
Fixes: 3ac6d8c787 ("x86/entry/64: Clear registers for exceptions/interrupts, to reduce speculation attack surface")
Link: http://lkml.kernel.org/r/b5010a090d3586b2d6e06c7ad3ec5542d1241c45.1532282627.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c8e8cd579b upstream.
'call' is a user-controlled value, so sanitize the array index after the
bounds check to avoid speculating past the bounds of the 'nargs' array.
Found with the help of Smatch:
net/socket.c:2508 __do_sys_socketcall() warn: potential spectre issue
'nargs' [r] (local cap)
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jeremy Cline <jcline@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 72c05f32f4 upstream.
ems_usb_probe() allocates memory for dev->tx_msg_buffer, but there
is no its deallocation in ems_usb_disconnect().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 71755ee535 upstream.
The squashfs fragment reading code doesn't actually verify that the
fragment is inside the fragment table. The end result _is_ verified to
be inside the image when actually reading the fragment data, but before
that is done, we may end up taking a page fault because the fragment
table itself might not even exist.
Another report from Anatoly and his endless squashfs image fuzzing.
Reported-by: Анатолий Тросиненко <anatoly.trosinenko@gmail.com>
Acked-by:: Phillip Lougher <phillip.lougher@gmail.com>,
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d512584780 upstream.
Anatoly reports another squashfs fuzzing issue, where the decompression
parameters themselves are in a compressed block.
This causes squashfs_read_data() to be called in order to read the
decompression options before the decompression stream having been set
up, making squashfs go sideways.
Reported-by: Anatoly Trosinenko <anatoly.trosinenko@gmail.com>
Acked-by: Phillip Lougher <phillip.lougher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8e1d162d8e ]
After introduction of the cited commit, mlx5e_build_nic_params
receives the netdevice mtu in order to set the sw_mtu of mlx5e_params.
For enhanced IPoIB, the netdevice mtu is not set in this stage,
therefore, the initial sw_mtu equals zero. As a result, the hw_mtu
of the receive queue will be calculated incorrectly causing traffic
issues.
To fix this issue, query for port mtu before building the nic params.
Fixes: 472a1e44b3 ("net/mlx5e: Save MTU in channels params")
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2e8e70d249 ]
The hairpin offload code has dependency on the trust mode being PCP.
Hence we should set PCP as the default for handling cases where we are
disallowed to read the trust mode from the FW, or failed to initialize it.
Fixes: 106be53b6b ('net/mlx5e: Set per priority hairpin pairs')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5f5991f36d ]
Execute mlx5_eswitch_init() only if we have MLX5_ESWITCH_MANAGER
capabilities.
Do the same for mlx5_eswitch_cleanup().
Fixes: a9f7705ffd ("net/mlx5: Unify vport manager capability check")
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c01f6c9b32 ]
There just check the user call ID isn't already in use, hence should
compare user_call_ID with xcall->user_call_ID, which is current
node's user_call_ID.
Fixes: 540b1c48c3 ("rxrpc: Fix deadlock between call creation and sendmsg/recvmsg")
Suggested-by: David Howells <dhowells@redhat.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bc5b6c0b62 ]
'protocol' is a user-controlled value, so sanitize it after the bounds
check to avoid using it for speculative out-of-bounds access to arrays
indexed by it.
This addresses the following accesses detected with the help of smatch:
* net/netlink/af_netlink.c:654 __netlink_create() warn: potential
spectre issue 'nlk_cb_mutex_keys' [w]
* net/netlink/af_netlink.c:654 __netlink_create() warn: potential
spectre issue 'nlk_cb_mutex_key_strings' [w]
* net/netlink/af_netlink.c:685 netlink_create() warn: potential spectre
issue 'nl_table' [w] (local cap)
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Jeremy Cline <jcline@redhat.com>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a94c689e6c ]
If a DSA slave network device was previously disabled, there is no need
to suspend or resume it.
Fixes: 2446254915 ("net: dsa: allow switch drivers to implement suspend/resume hooks")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4672694bd4 ]
ip_frag_queue() might call pskb_pull() on one skb that
is already in the fragment queue.
We need to take care of possible truesize change, or we
might have an imbalance of the netns frags memory usage.
IPv6 is immune to this bug, because RFC5722, Section 4,
amended by Errata ID 3089 states :
When reassembling an IPv6 datagram, if
one or more its constituent fragments is determined to be an
overlapping fragment, the entire datagram (and any constituent
fragments) MUST be silently discarded.
Fixes: 158f323b98 ("net: adjust skb->truesize in pskb_expand_head()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 56e2c94f05 ]
We currently check current frags memory usage only when
a new frag queue is created. This allows attackers to first
consume the memory budget (default : 4 MB) creating thousands
of frag queues, then sending tiny skbs to exceed high_thresh
limit by 2 to 3 order of magnitude.
Note that before commit 648700f76b ("inet: frags: use rhashtables
for reassembly units"), work queue could be starved under DOS,
getting no cpu cycles.
After commit 648700f76b, only the per frag queue timer can eventually
remove an incomplete frag queue and its skbs.
Fixes: b13d3cbfb8 ("inet: frag: move eviction of queues to work queue")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jann Horn <jannh@google.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: Peter Oskolkov <posk@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 460a53106a upstream.
Previous change in the AML parser code blindly set all non-successful
dispatcher statuses to AE_OK. That approach is incorrect, though,
because successful control method invocations from module-level
return AE_CTRL_TRANSFER. Overwriting AE_OK to this status causes the
AML parser to think that there was no return value from the control
method invocation.
Fixes: 92c0f4af386 (ACPICA: AML Parser: ignore dispatcher error status during table load)
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 12864ff854 upstream.
Commit a09c591306 (ACPI / LPSS: Avoid PM quirks on suspend and
resume from S3) modified the ACPI driver for Intel SoCs (LPSS) to
avoid applying PM quirks on suspend and resume from S3 to address
system-wide suspend and resume problems on some systems, but it is
reported that the same issue also affects hibernation, so extend
the approach used by that commit to cover hibernation as well.
Fixes: a09c591306 (ACPI / LPSS: Avoid PM quirks on suspend and resume from S3)
Link: https://bugs.launchpad.net/bugs/1774950
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: 4.15+ <stable@vger.kernel.org> # 4.15+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 15ecbe94a4 ]
Larry Brakmo proposal ( https://patchwork.ozlabs.org/patch/935233/
tcp: force cwnd at least 2 in tcp_cwnd_reduction) made us rethink
about our recent patch removing ~16 quick acks after ECN events.
tcp_enter_quickack_mode(sk, 1) makes sure one immediate ack is sent,
but in the case the sender cwnd was lowered to 1, we do not want
to have a delayed ack for the next packet we will receive.
Fixes: 522040ea5f ("tcp: do not aggressively quick ack after ECN events")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Neal Cardwell <ncardwell@google.com>
Cc: Lawrence Brakmo <brakmo@fb.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 522040ea5f ]
ECN signals currently forces TCP to enter quickack mode for
up to 16 (TCP_MAX_QUICKACKS) following incoming packets.
We believe this is not needed, and only sending one immediate ack
for the current packet should be enough.
This should reduce the extra load noticed in DCTCP environments,
after congestion events.
This is part 2 of our effort to reduce pure ACK packets.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9a9c9b51e5 ]
We want to add finer control of the number of ACK packets sent after
ECN events.
This patch is not changing current behavior, it only enables following
change.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a3893637e1 ]
As explained in commit 9f9843a751 ("tcp: properly handle stretch
acks in slow start"), TCP stacks have to consider how many packets
are acknowledged in one single ACK, because of GRO, but also
because of ACK compression or losses.
We plan to add SACK compression in the following patch, we
must therefore not call tcp_enter_quickack_mode()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 61f4b23769 ]
On i386 nlk->ngroups might be 32 or 0. Which leads to UB, resulting in
hang during boot.
Check for 0 ngroups and use (unsigned long long) as a type to shift.
Fixes: 7acf9d4237 ("netlink: Do not subscribe to non-existent groups").
Reported-by: kernel test robot <rong.a.chen@intel.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7effaf06c3 ]
Fix dev_change_tx_queue_len so it rolls back original value
upon a failure in dev_qdisc_change_tx_queue_len.
This is already done for notifirers' failures, share the code.
In case of failure in dev_qdisc_change_tx_queue_len, some tx queues
would still be of the new length, while they should be reverted.
Currently, the revert is not done, and is marked with a TODO label
in dev_qdisc_change_tx_queue_len, and should find some nice solution
to do it.
Yet it is still better to not apply the newly requested value.
Fixes: 48bfd55e7e ("net_sched: plug in qdisc ops change_tx_queue_len")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Reported-by: Ran Rozenstein <ranro@mellanox.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 942a656f1f ]
Break statements were missing for Geneve case in
ndo_udp_tunnel_{add/del}, thereby raw mac matchall
entries were not getting added.
Fixes: c746fc0e8b2d("cxgb4: add geneve offload support for T6")
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 822fb18a82 ]
When loading module manually, after call xenbus_switch_state to initializes
the state of the netfront device, the driver state did not change so fast
that may lead no dev created in latest kernel. This patch adds wait to make
sure xenbus knows the driver is not in closed/unknown state.
Current state:
[vm]# ethtool eth0
Settings for eth0:
Link detected: yes
[vm]# modprobe -r xen_netfront
[vm]# modprobe xen_netfront
[vm]# ethtool eth0
Settings for eth0:
Cannot get device settings: No such device
Cannot get wake-on-lan settings: No such device
Cannot get message level: No such device
Cannot get link status: No such device
No data available
With the patch installed.
[vm]# ethtool eth0
Settings for eth0:
Link detected: yes
[vm]# modprobe -r xen_netfront
[vm]# modprobe xen_netfront
[vm]# ethtool eth0
Settings for eth0:
Link detected: yes
Signed-off-by: Xiao Liang <xiliang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ecbc42ca5d ]
When received packets are dropped in virtio_net driver, received packets
counter is incremented but bytes counter is not.
As a result, for instance if we drop all packets by XDP, only received
is counted and bytes stays 0, which looks inconsistent.
IMHO received packets/bytes should be counted if packets are produced by
the hypervisor, like what common NICs on physical machines are doing.
So fix the bytes counter.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 383d470936 ]
For some very small BDPs (with just a few packets) there was a
quantization effect where the target number of packets in flight
during the super-unity-gain (1.25x) phase of gain cycling was
implicitly truncated to a number of packets no larger than the normal
unity-gain (1.0x) phase of gain cycling. This meant that in multi-flow
scenarios some flows could get stuck with a lower bandwidth, because
they did not push enough packets inflight to discover that there was
more bandwidth available. This was really only an issue in multi-flow
LAN scenarios, where RTTs and BDPs are low enough for this to be an
issue.
This fix ensures that gain cycling can raise inflight for small BDPs
by ensuring that in PROBE_BW mode target inflight values with a
super-unity gain are always greater than inflight values with a gain
<= 1. Importantly, this applies whether the inflight value is
calculated for use as a cwnd value, or as a target inflight value for
the end of the super-unity phase in bbr_is_next_cycle_phase() (both
need to be bigger to ensure we can probe with more packets in flight
reliably).
This is a candidate fix for stable releases.
Fixes: 0f8782ea14 ("tcp_bbr: add BBR congestion control")
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Priyaranjan Jha <priyarjha@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9939a46d90 ]
As for today STMMAC_ALIGN macro (which is used to align DMA stuff)
relies on L1 line length (L1_CACHE_BYTES).
This isn't correct in case of system with several cache levels
which might have L1 cache line length smaller than L2 line. This
can lead to sharing one cache line between DMA buffer and other
data, so we can lose this data while invalidate DMA buffer before
DMA transaction.
Fix that by using SMP_CACHE_BYTES instead of L1_CACHE_BYTES for
aligning.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b0753408aa ]
mdio_mux_iproc_probe() uses platform_set_drvdata() to store md pointer
in device, whereas mdio_mux_iproc_remove() restores md pointer by
dev_get_platdata(&pdev->dev). This leads to wrong resources release.
The patch replaces getter to platform_get_drvdata.
Fixes: 98bc865a1e ("net: mdio-mux: Add MDIO mux driver for iProc SoCs")
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 136f55f660 ]
As long the bh tasklet isn't scheduled once, no packet from the rx path
will be handled. Since the tx path also schedule the same tasklet
this situation only persits until the first packet transmission.
So fix this issue by scheduling the tasklet after link reset.
Link: https://github.com/raspberrypi/linux/issues/2617
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet")
Suggested-by: Floris Bos <bos@je-eigen-domein.nl>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7f3fc7ddf7 ]
If we enable or disable xgbe flow-control by ethtool ,
it does't work.Because the parameter is not properly
assigned,so we need to adjust the assignment order
of the parameters.
Fixes: c1ce2f7736 ("amd-xgbe: Fix flow control setting logic")
Signed-off-by: tangpengpeng <tangpengpeng@higon.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 101f0cd4f2 ]
UBSAN triggers the following undefined behaviour warnings:
[...]
[ 13.236124] UBSAN: Undefined behaviour in drivers/net/ethernet/amazon/ena/ena_eth_com.c:468:22
[ 13.240043] shift exponent 64 is too large for 64-bit type 'long long unsigned int'
[...]
[ 13.744769] UBSAN: Undefined behaviour in drivers/net/ethernet/amazon/ena/ena_eth_com.c:373:4
[ 13.748694] shift exponent 64 is too large for 64-bit type 'long long unsigned int'
[...]
When splitting the address to high and low, GENMASK_ULL is used to generate
a bitmask with dma_addr_bits field from io_sq (in ena_com_prepare_tx and
ena_com_add_single_rx_desc).
The problem is that dma_addr_bits is not initialized with a proper value
(besides being cleared in ena_com_create_io_queue).
Assign dma_addr_bits the correct value that is stored in ena_dev when
initializing the SQ.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Gal Pressman <pressmangal@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9fc12023d6 ]
Remove BUG_ON() from fib_compute_spec_dst routine and check
in_dev pointer during flowi4 data structure initialization.
fib_compute_spec_dst routine can be run concurrently with device removal
where ip_ptr net_device pointer is set to NULL. This can happen
if userspace enables pkt info on UDP rx socket and the device
is removed while traffic is flowing
Fixes: 35ebf65e85 ("ipv4: Create and use fib_compute_spec_dst() helper")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eee1fe6476 upstream.
When a port is brought up/down do not enable/disable only the TXMAC
but the RXMAC as well. This is essential for the CPU port to work.
Fixes: 6b93fb4648 ("net-next: dsa: add new driver for qca8xxx family")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 79a4ed4f0f upstream.
By default autonegotiation is enabled to configure MAC on all ports.
For the CPU port autonegotiation can not be used so we need to set
some sensible defaults manually.
This patch forces the default setting of the CPU port to 1000Mbps/full
duplex which is the chip maximum capability.
Also correct size of the bit field used to configure link speed.
Fixes: 6b93fb4648 ("net-next: dsa: add new driver for qca8xxx family")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 940efcc888 upstream.
Flows can be created on UD and RAW_PACKET QP types. Attempts to provide
other QP types as an input causes to various unpredictable failures.
The reason is that in order to support all various types (e.g. XRC), we
are supposed to use real_qp handle and not qp handle and expect to
driver/FW to fail such (XRC) flows. The simpler and safer variant is to
ban all QP types except UD and RAW_PACKET, instead of relying on
driver/FW.
Cc: <stable@vger.kernel.org> # 3.11
Fixes: 436f2ad05a ("IB/core: Export ib_create/destroy_flow through uverbs")
Cc: syzkaller <syzkaller@googlegroups.com>
Reported-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bbfbf04c2d upstream.
If a GPIO chip is a part of a hierarchy IRQ domain, there is no
way to specify the trigger type when gpio(d)_to_irq() allocates an
interrupt on-the-fly.
Currently, uniphier_gpio_to_irq() sets IRQ_TYPE_NONE, but it causes
an error in the .alloc() hook of the parent domain.
(drivers/irq/irq-uniphier-aidet.c)
Even if we change irq-uniphier-aidet.c to accept the NONE type,
GIC complains about it since commit 83a86fbb5b ("irqchip/gic:
Loudly complain about the use of IRQ_TYPE_NONE").
Instead, use IRQ_TYPE_LEVEL_HIGH as a temporary value when an irq
is allocated. irq_set_irq_type() will override it when the irq is
really requested.
Fixes: dbe776c2ca ("gpio: uniphier: add UniPhier GPIO controller driver")
Reported-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 906402a44b upstream.
This fixes up the handling of fixed regulator polarity
inversion flags: while I remembered to fix it for the
undocumented "reg-fixed-voltage" I forgot about the
official "regulator-fixed" binding, there are two ways
to do a fixed regulator.
The error was noticed and fixed.
Fixes: a603a2b8d8 ("gpio: of: Add special quirk to parse regulator flags")
Cc: Mark Brown <broonie@kernel.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Reported-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5012284700 upstream.
Commit 8844618d8a: "ext4: only look at the bg_flags field if it is
valid" will complain if block group zero does not have the
EXT4_BG_INODE_ZEROED flag set. Unfortunately, this is not correct,
since a freshly created file system has this flag cleared. It gets
almost immediately after the file system is mounted read-write --- but
the following somewhat unlikely sequence will end up triggering a
false positive report of a corrupted file system:
mkfs.ext4 /dev/vdc
mount -o ro /dev/vdc /vdc
mount -o remount,rw /dev/vdc
Instead, when initializing the inode table for block group zero, test
to make sure that itable_unused count is not too large, since that is
the case that will result in some or all of the reserved inodes
getting cleared.
This fixes the failures reported by Eric Whiteney when running
generic/230 and generic/231 in the the nojournal test case.
Fixes: 8844618d8a ("ext4: only look at the bg_flags field if it is valid")
Reported-by: Eric Whitney <enwlinux@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d5a803c6a upstream.
With commit 044e6e3d74: "ext4: don't update checksum of new
initialized bitmaps" the buffer valid bit will get set without
actually setting up the checksum for the allocation bitmap, since the
checksum will get calculated once we actually allocate an inode or
block.
If we are doing this, then we need to (re-)check the verified bit
after we take the block group lock. Otherwise, we could race with
another process reading and verifying the bitmap, which would then
complain about the checksum being invalid.
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1780137
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 362eca70b5 upstream.
The inline data code was updating the raw inode directly; this is
problematic since if metadata checksums are enabled,
ext4_mark_inode_dirty() must be called to update the inode's checksum.
In addition, the jbd2 layer requires that get_write_access() be called
before the metadata buffer is modified. Fix both of these problems.
https://bugzilla.kernel.org/show_bug.cgi?id=200443
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 44de022c43 upstream.
Ext4_check_descriptors() was getting called before s_gdb_count was
initialized. So for file systems w/o the meta_bg feature, allocation
bitmaps could overlap the block group descriptors and ext4 wouldn't
notice.
For file systems with the meta_bg feature enabled, there was a
fencepost error which would cause the ext4_check_descriptors() to
incorrectly believe that the block allocation bitmap overlaps with the
block group descriptor blocks, and it would reject the mount.
Fix both of these problems.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 01cfb7937a upstream.
Anatoly Trosinenko reports that a corrupted squashfs image can cause a
kernel oops. It turns out that squashfs can end up being confused about
negative fragment lengths.
The regular squashfs_read_data() does check for negative lengths, but
squashfs_read_metadata() did not, and the fragment size code just
blindly trusted the on-disk value. Fix both the fragment parsing and
the metadata reading code.
Reported-by: Anatoly Trosinenko <anatoly.trosinenko@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Phillip Lougher <phillip@squashfs.org.uk>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81e69df38e upstream.
Fedora has integrated the jitter entropy daemon to work around slow
boot problems, especially on VM's that don't support virtio-rng:
https://bugzilla.redhat.com/show_bug.cgi?id=1572944
It's understandable why they did this, but the Jitter entropy daemon
works fundamentally on the principle: "the CPU microarchitecture is
**so** complicated and we can't figure it out, so it *must* be
random". Yes, it uses statistical tests to "prove" it is secure, but
AES_ENCRYPT(NSA_KEY, COUNTER++) will also pass statistical tests with
flying colors.
So if RDRAND is available, mix it into entropy submitted from
userspace. It can't hurt, and if you believe the NSA has backdoored
RDRAND, then they probably have enough details about the Intel
microarchitecture that they can reverse engineer how the Jitter
entropy daemon affects the microarchitecture, and attack its output
stream. And if RDRAND is in fact an honest DRNG, it will immeasurably
improve on what the Jitter entropy daemon might produce.
This also provides some protection against someone who is able to read
or set the entropy seed file.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b16fd6305 upstream.
On Gen3, we can only do RXDMA once per transfer reliably. For that, we
must reset the device, then we can have RXDMA once. This patch
implements this. When there is no reset controller or the reset fails,
RXDMA will be blocked completely. Otherwise, it will be disabled after
the first RXDMA transfer. Based on a commit from the BSP by Hiromitsu
Yamasaki, yet completely refactored to handle multiple read messages
within one transfer.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d082dc1562 upstream.
The existing code to carve up the sg list expected an sg element-per-page
which can be very incorrect with iommu's remapping multiple memory pages
to fewer bus addresses. To hit this error required a large io payload
(greater than 256k) and a system that maps on a per-page basis. It's
possible that large ios could get by fine if the system condensed the
sgl list into the first 64 elements.
This patch corrects the sg list handling by specifically walking the
sg list element by element and attempting to divide the transfer up
on a per-sg element boundary. While doing so, it still tries to keep
sequences under 256k, but will exceed that rule if a single sg element
is larger than 256k.
Fixes: 48fa362b6c ("nvmet-fc: simplify sg list handling")
Cc: <stable@vger.kernel.org> # 4.14
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5151842b9d upstream.
After the bio has been updated to represent the remaining sectors, reset
bi_done so bio_rewind_iter() does not rewind further than it should.
This resolves a bio_integrity_process() failure on reads where the
original request was split.
Fixes: 63573e359d ("bio-integrity: Restore original iterator on verify stage")
Signed-off-by: Greg Edwards <gedwards@ddn.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b403ea2404 upstream.
If the last page of the bio is not "full", the length of the last
vector slot needs to be corrected. This slot has the index
(bio->bi_vcnt - 1), but only in bio->bi_io_vec. In the "bv" helper
array, which is shifted by the value of bio->bi_vcnt at function
invocation, the correct index is (nr_pages - 1).
v2: improved readability following suggestions from Ming Lei.
v3: followed a formatting suggestion from Christoph Hellwig.
Fixes: 2cefe4dbaa ("block: add bio_iov_iter_get_pages()")
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6e08e0995b ]
When an MMU notifier runs in memory reclaim context, it can deadlock
trying to take locks that are already held in the thread causing the
memory reclaim. The solution is to avoid memory reclaim while holding
locks that are taken in MMU notifiers.
This commit fixes kmalloc while holding rmn->lock by moving the call
outside the lock. The GFX MMU notifier also locks reservation objects.
I have no good solution for avoiding reclaim while holding reservation
objects. The HSA MMU notifier will not lock any reservation objects.
v2: Moved allocation outside lock instead of using GFP_NOIO
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Oded Gabbay <oded.gabbay@gmail.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5e9cfeba6a ]
drm_atomic_helper_shutdown() needs to release the reference held by
plane->fb. Since commit 49d70aeaec ("drm/atomic-helper: Fix leak in
disable_all") we're doing that by calling drm_atomic_clean_old_fb() in
drm_atomic_helper_disable_all(). This also leaves plane->fb == NULL
afterwards. However, since drm_atomic_helper_disable_all() is also
used by the i915 gpu reset code
drm_atomic_helper_commit_duplicated_state() then has to undo the
damage and put the correct plane->fb pointers back in (and also
adjust the ref counts to match again as well).
That approach doesn't work so well for load detection as nothing
sets up the plane->old_fb pointers for us. This causes us to
leak an extra reference for each plane->fb when
drm_atomic_helper_commit_duplicated_state() calls
drm_atomic_clean_old_fb() after load detection.
To fix this let's call drm_atomic_clean_old_fb() only for
drm_atomic_helper_shutdown() as that's the only time we need to
actually drop the plane->fb references. In all the other cases
(load detection, gpu reset) we want to leave plane->fb alone.
v2: Don't inflict the clean_old_fbs bool to drivers (Daniel)
v3: Squash in the revert and rewrite the commit msg (Daniel)
Cc: martin.peres@free.fr
Cc: chris@chris-wilson.co.uk
Cc: Dave Airlie <airlied@gmail.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180322152313.6561-3-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> #pre-squash
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6e1386b2ee ]
sgtl5000 codec needs MCLK clock to be present so that it can
successfully read/write via I2C.
In the case of wandboard, MCLK is provided via
MX6QDL_PAD_GPIO_0__CCM_CLKO1 pad.
Move the MCLK pinctrl from hog group to the codec group, so that the
codec clock can be present prior to reading the codec ID.
This avoids the following error that happens from time to time:
[ 2.484443] sgtl5000 1-000a: Error reading chip id -6
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 933e1c4a66 ]
Clock gating parameter is a part of `dai_fmt`. It is supported by
`alsa-lib` when creating a topology binary file, but ignored by kernel
when loading this topology file.
After applying this commit, the clock gating parameter is not ignored any
more. This solution is backwards compatible. The existing behaviour is
not broken, because by default the parameter value is 0 and is ignored.
snd_soc_tplg_hw_config.clock_gated = 0 => no effect
snd_soc_tplg_hw_config.clock_gated = 1 => SND_SOC_DAIFMT_GATED
snd_soc_tplg_hw_config.clock_gated = 2 => SND_SOC_DAIFMT_CONT
For example, the following config, based on
alsa-lib/src/conf/topology/broadwell/broadwell.conf, is now supported:
~~~~
SectionHWConfig."CodecHWConfig" {
id "1"
format "I2S" # physical audio format.
pm_gate_clocks "true" # clock can be gated
}
SectionLink."Codec" {
# used for binding to the physical link
id "0"
hw_configs [
"CodecHWConfig"
]
default_hw_conf_id "1"
}
~~~~
Signed-off-by: Kirill Marinushkin <k.marinushkin@gmail.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Mark Brown <broonie@kernel.org>
Cc: Pan Xiuli <xiuli.pan@linux.intel.com>
Cc: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Cc: alsa-devel@alsa-project.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9a00b697ce ]
When the interface is down, head/tail of the descriptor
ring address is set to 0 in netsec_netdev_stop().
But netsec hardware still keeps the previous descriptor
ring address, so there is inconsistency between driver
and hardware after interface is up at a later time.
To address this inconsistency, add netsec_reset_hardware()
when the interface is down.
In addition, to minimize the reset process,
add flag to decide whether driver loads the netsec microcode.
Even if driver resets the netsec hardware, netsec microcode
keeps resident on RAM, so it is ok we only load the microcode
at initialization.
This patch is critical for installation over network.
Signed-off-by: Masahisa KOJIMA <masahisa.kojima@linaro.org>
Fixes: 533dd11a12 ("net: socionext: Add Synquacer NetSec driver")
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b66d448487 ]
drivers/media/cec/cec-pin-error-inj.c:231
cec_pin_error_inj_parse_line() error: uninitialized symbol 'pos'.
The tx-add-bytes command didn't check for the presence of an argument, and
also didn't check that it was > 0.
This should fix this error.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9ab105deb6 ]
When in the ASPM L1.0 state (but not the PCI-PM L1.0 state), the most
recent LTR value and the LTR_L1.2_THRESHOLD determines whether the link
enters the L1.2 substate.
If we don't have LTR enabled, prevent the use of ASPM L1.2.
PCI-PM L1.2 may still be used because it doesn't depend on
LTR_L1.2_THRESHOLD (see PCIe r4.0, sec 5.5.1).
Tested-by: Srinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 465891fe92 ]
The SISLite specification originally defined the context control register with
a single field of bits to represent the LISN and also stipulated that the
register reset value be 0. The cxlflash driver took advantage of this when
programming the LISN for the master contexts via an unconditional write - no
other bits were preserved.
When unmap support was added, SISLite was updated to define bit 0 of the
context control register as a way for the AFU to notify the context owner that
unmap operations were supported. Thus the assumptions under which the register
is setup changed and the existing unconditional write is clobbering the unmap
state for master contexts. This is presently not an issue due to the order in
which the context control register is programmed in relation to the unmap bit
being queried but should be addressed to avoid a future regression in the
event this code is moved elsewhere.
To remedy this issue, preserve the bits when programming the LISN field in the
context control register. Since the LISN will now be programmed using a read
value, assert that the initial state of the LISN field is as described in
SISLite (0).
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a3feb6ef50 ]
The following Oops can be encountered if a device removal or system shutdown
is initiated while an EEH recovery is in process:
[c000000ff2f479c0] c008000015256f18 cxlflash_pci_slot_reset+0xa0/0x100
[cxlflash]
[c000000ff2f47a30] c00800000dae22e0 cxl_pci_slot_reset+0x168/0x290 [cxl]
[c000000ff2f47ae0] c00000000003ef1c eeh_report_reset+0xec/0x170
[c000000ff2f47b20] c00000000003d0b8 eeh_pe_dev_traverse+0x98/0x170
[c000000ff2f47bb0] c00000000003f80c eeh_handle_normal_event+0x56c/0x580
[c000000ff2f47c60] c00000000003fba4 eeh_handle_event+0x2a4/0x338
[c000000ff2f47d10] c0000000000400b8 eeh_event_handler+0x1f8/0x200
[c000000ff2f47dc0] c00000000013da48 kthread+0x1a8/0x1b0
[c000000ff2f47e30] c00000000000b528 ret_from_kernel_thread+0x5c/0xb4
The remove handler frees AFU memory while the EEH recovery is in progress,
leading to a race condition. This can result in a crash if the recovery thread
tries to access this memory.
To resolve this issue, the cxlflash remove handler will evaluate the device
state and yield to any active reset or probing threads.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3239b8cd28 ]
Hardware could time out Fastpath IOs one second earlier than the timeout
provided by the host.
For non-RAID devices, driver provides timeout value based on OS provided
timeout value. Under certain scenarios, if the OS provides a timeout
value of 1 second, due to above behavior hardware will timeout
immediately.
Increase timeout value for non-RAID fastpath IOs by 1 second.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c848966806 ]
commit f2593cb1b2 ("ath10k: Search SMBIOS for OEM board file
extension") added a feature to ath10k that allows Board Data File
(BDF) conflicts between multiple devices that use the same device IDs
but have different calibration requirements to be resolved by allowing
a "variant" string to be stored in SMBIOS [and later device tree, added
by commit d06f26c5c8 ("ath10k: search DT for qcom,ath10k-calibration-
variant")] that gets appended to the ID stored in board-2.bin.
This original patch had a regression, however. Namely that devices with
a variant present in SMBIOS that didn't need custom BDFs could no longer
find the default BDF, which has no variant appended. The patch was
reverted and re-applied with a fix for this issue in commit 1657b8f84e
("search SMBIOS for OEM board file extension").
But the fix to fall back to a default BDF introduced another issue: the
driver currently parses IEs in board-2.bin one by one, and for each one
it first checks to see if it matches the ID with the variant appended.
If it doesn't, it checks to see if it matches the "fallback" ID with no
variant. If a matching BDF is found at any point during this search, the
search is terminated and that BDF is used. The issue is that it's very
possible (and is currently the case for board-2.bin files present in the
ath10k-firmware repository) for the default BDF to occur in an earlier
IE than the variant-specific BDF. In this case, the current code will
happily choose the default BDF even though a better-matching BDF is
present later in the file.
This patch fixes the issue by first searching the entire file for the ID
with variant, and searching for the fallback ID only if that search
fails. It also includes some code cleanup in the area, as
ath10k_core_fetch_board_data_api_n() no longer does its own string
mangling to remove the variant from an ID, instead leaving that job to a
new flag passed to ath10k_core_create_board_name().
I've tested this patch on a QCA4019 and verified that the driver behaves
correctly for 1) both fallback and variant BDFs present, 2) only fallback
BDF present, and 3) no matching BDFs present.
Fixes: 1657b8f84e ("ath10k: search SMBIOS for OEM board file extension")
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 02f3703934 ]
In of_get_regulation_constraints() we were taking the result of
of_map_mode() (an unsigned int) and assigning it to an int. We were
then checking whether this value was -EINVAL. Some implementers of
of_map_mode() were returning -EINVAL (even though the return type of
their function needed to be unsigned int) because they needed to
signal an error back to of_get_regulation_constraints().
In general in the regulator framework the mode is always referred to
as an unsigned int. While we could fix this to be a signed int (the
highest value we store in there right now is 0x8), it's actually
pretty clean to just define the regulator mode 0x0 (the lack of any
bits set) as an invalid mode. Let's do that.
Fixes: 5e5e3a42c6 ("regulator: of: Add support for parsing initial and suspend modes")
Suggested-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b7e1e6859f ]
The OMAP3 ISP driver manages its MMU mappings through the IOMMU-aware
ARM DMA backend. The current code creates a dma_iommu_mapping and
attaches this to the ISP device, but never detaches the mapping in
either the probe failure paths or the driver remove path resulting
in an unbalanced mapping refcount and a memory leak. Fix this properly.
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Suman Anna <s-anna@ti.com>
Tested-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c421c62a4a ]
The mce keyboard repeats pressed keys every 100ms. If the IR timeout
is set to less than that, we send key up events before the repeat
arrives, so we have key up/key down for each IR repeat.
The keyboard ends any sequence with a 0 scancode, in which case all keys
are cleared so there is no need to run the timeout timer: it only exists
for the case that the final 0 was not received.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2a70b7879b ]
In some places, we still used get_seconds() instead of
ktime_get_real_seconds(), and I'm changing the remaining ones now to
all use ktime_get_real_seconds() so we use the full available range for
timestamps instead of overflowing the 'unsigned long' return value in
year 2106 on 32-bit kernels.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 31545df391 ]
In crypto_authenc_esn_setkey we save pointers to the authenc keys
in a local variable of type struct crypto_authenc_keys and we don't
zeroize it after use. Fix this and don't leak pointers to the
authenc keys.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5d111f5190 ]
wait_for_connected() wait till a port change status to
USB_PORT_STAT_CONNECTION, but this is not possible if
the port is unpowered. The loop will only exit at timeout.
Such case take place if an over-current incident happen
while system is in S3. Then during resume wait_for_connected()
will wait 2s, which may be noticeable by the user.
Signed-off-by: Dominik Bozek <dominikx.bozek@intel.com>
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ece97f3a5f ]
simpleImage generation was broken for some time. This patch is fixing
steps how simpleImage.*.ub file is generated. Steps are objdump of
vmlinux and create .ub.
Also make sure that there is striped elf version with .strip suffix.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 050f810e23 ]
Platform device core assumes the ownership of dev.platform_data as
well as that it is dynamically allocated and it will try to kfree it
as a part of platform_device_release(). Change the code to use
platform_device_add_data() n instead of a pointer to a static memory
to avoid causing a BUG() when calling platform_device_put().
The problem can be reproduced by artificially enabling the error path
of platform_device_add() call (around line 357).
Note that this change also allows us to constify imx7_pgc_domains,
since we no longer need to be able to modify it.
Cc: Stefan Agner <stefan@agner.ch>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c1c734cb1f ]
As part of bringup I ended up wanting to call an earlycon driver by a
name that was exactly 16-bytes big, specifically "qcom_geni_serial".
Unfortunately, when I tried this I found that things compiled just
fine. They just didn't work.
Specifically the compiler felt perfectly justified in initting the
".name" field of "struct earlycon_id" with the full 16-bytes and just
skipping the '\0'. Needless to say, that behavior didn't seem ideal,
but I guess someone must have allowed it for a reason.
One way to fix this is to shorten the name field to 15 bytes and then
add an extra byte after that nobody touches. This should always be
initted to 0 and we're golden.
There are, of course, other ways to fix this too. We could audit all
the users of the "name" field and make them stop at both null
termination or at 16 bytes. We could also just make the name field
much bigger so that we're not likely to run into this. ...but both
seem like we'll just hit the bug again.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b004b21cc6 ]
Sergey reported that some much older Dell systems don't support
the OEM string "Dell System" but instead supported www.dell.com
in OEM strings.
Match both of these to indicate that this driver is running on
a Dell system.
Reported-by: Sergey Kubushyn <ksi@koi8.net>
Tested-by: Sergey Kubushyn <ksi@koi8.net>
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
[dvhart: Simplify DMI logic and eliminate unnecessary variables]
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 300eec7c0a ]
ic_nameservers, which stores the list of name servers discovered by
ipconfig, is initialised (i.e. has all of its elements set to NONE, or
0xffffffff) by ic_nameservers_predef() in the following scenarios:
- before the "ip=" and "nfsaddrs=" kernel command line parameters are
parsed (in ip_auto_config_setup());
- before autoconfiguring via DHCP or BOOTP (in ic_bootp_init()), in
order to clear any values that may have been set after parsing "ip="
or "nfsaddrs=" and are no longer needed.
This means that ic_nameservers_predef() is not called when neither "ip="
nor "nfsaddrs=" is specified on the kernel command line. In this
scenario, every element in ic_nameservers remains set to 0x00000000,
which is indistinguishable from ANY and causes pnp_seq_show() to write
the following (bogus) information to /proc/net/pnp:
#MANUAL
nameserver 0.0.0.0
nameserver 0.0.0.0
nameserver 0.0.0.0
This is potentially problematic for systems that blindly link
/etc/resolv.conf to /proc/net/pnp.
Ensure that ic_nameservers is also initialised when neither "ip=" nor
"nfsaddrs=" are specified by calling ic_nameservers_predef() in
ip_auto_config(), but only when ip_auto_config_setup() was not called
earlier. This causes the following to be written to /proc/net/pnp, and
is consistent with what gets written when ipconfig is configured
manually but no name servers are specified on the kernel command line:
#MANUAL
Signed-off-by: Chris Novakovic <chris@chrisn.me.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4dc93fcf0b ]
On the RAH registers there are semantic differences on the meaning of
the "queue" parameter for traffic steering depending on the controller
model: there is the 82575 meaning, which "queue" means a RX Hardware
Queue, and the i350 meaning, where it is a reception pool.
The previous behaviour was having no effect for i210 based controllers
because the QSEL bit of the RAH register wasn't being set.
This patch separates the condition in discrete cases, so the different
handling is clearer.
Fixes: 83c21335c8 ("igb: improve MAC filter handling")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 572e6c8dd1 ]
The core should only call free on a component if said component has
already had open called on it. This is not presently the case and most
compressed drivers in the kernel assume it will be. This causes null
pointer dereferences in the drivers as they attempt clean up for stuff
that was never put in place.
This is fixed by aborting calling open callbacks once a failure is
encountered and then during clean up only iterating through the
component list to that point.
This is a fairly quick fix to the issue, to allow backporting. There
is more refactoring to follow to tidy the code up a little.
Fixes: 9e7e3738ab ("ASoC: snd_soc_component_driver has snd_compr_ops")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7c8b77f815 ]
Heiko Stübner justified pretty well the change in commit e330eb86ba
("ARM: multi_v7_defconfig: enable Rockchip io-domain driver"). This
change is also needed for arm64 rockchip boards, so, do the same for arm64.
The io-domain driver is necessary to notify the soc about voltages
changes happening on supplying regulators. Probably the most important
user right now is the mmc tuning code, where the soc needs to get
notified when the voltage is dropped to the 1.8V point.
As this option is necessary to successfully tune UHS cards etc, it
should get built in. Otherwise, tuning will fail with,
dwmmc_rockchip fe320000.dwmmc: All phases bad!
mmc0: tuning execution failed: -5
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 671f8204b1 ]
Convert the sisr and sisr2 variable types to u32 to avoid the following
sparse warnings:
sound/soc/fsl/fsl_ssi.c:391:42: warning: incorrect type in argument 3 (different base types)
sound/soc/fsl/fsl_ssi.c:391:42: expected unsigned int *val
sound/soc/fsl/fsl_ssi.c:391:42: got restricted __be32 *<noident>
sound/soc/fsl/fsl_ssi.c:393:17: warning: restricted __be32 degrades to integer
sound/soc/fsl/fsl_ssi.c:393:15: warning: incorrect type in assignment (different base types)
sound/soc/fsl/fsl_ssi.c:393:15: expected restricted __be32 [usertype] sisr2
sound/soc/fsl/fsl_ssi.c:393:15: got unsigned int
sound/soc/fsl/fsl_ssi.c:396:50: warning: incorrect type in argument 3 (different base types)
sound/soc/fsl/fsl_ssi.c:396:50: expected unsigned int [unsigned] val
sound/soc/fsl/fsl_ssi.c:396:50: got restricted __be32 [usertype] sisr2
sound/soc/fsl/fsl_ssi.c:398:42: warning: incorrect type in argument 2 (different base types)
sound/soc/fsl/fsl_ssi.c:398:42: expected unsigned int [unsigned] [usertype] sisr
sound/soc/fsl/fsl_ssi.c:398:42: got restricted __be32 [addressable] [usertype] sisr
In other places where regmap_read() is used a u32 variable is passed
to store the register read value, so do the same here as well.
regmap API already takes care of endianness, so the usage of u32 is safe.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1c74d5c0de ]
Currently we are enabling handling of interrupts specific to Tegra124+
which happen to overlap with previous generations. Let's specify
interrupts mask per SoC generation for consistency and in a preparation
of squashing of Tegra20 driver into the common one that will enable
handling of GART faults which may be undesirable by newer generations.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bf3fbdfbec ]
The ISR reads interrupts-enable mask, but doesn't utilize it. Apply the
mask to the interrupt status and don't handle interrupts that MC driver
haven't asked for. Kernel would disable spurious MC IRQ and report the
error. This would happen only in a case of a very severe bug.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 02acc80d19 ]
try_to_wake_up() might invoke delayacct_blkio_end() while holding the
pi_lock (which is a raw_spinlock_t). delayacct_blkio_end() acquires
task_delay_info.lock which is a spinlock_t. This causes a might sleep splat
on -RT where non raw spinlocks are converted to 'sleeping' spinlocks.
task_delay_info.lock is only held for a short amount of time so it's not a
problem latency wise to make convert it to a raw spinlock.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Balbir Singh <bsingharora@gmail.com>
Link: https://lkml.kernel.org/r/20180423161024.6710-1-bigeasy@linutronix.de
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 830e0dd999 ]
When operating at 1GbE, the base incval for the PTP clock is so large
that multiplying it by numbers close to the max_adj can overflow the
u64.
Rather than attempting to limit the max_adj to a value small enough to
avoid overflow, instead calculate the incvalue adjustment based on the
40GbE incvalue, and then multiply that by the scaling factor for the
link speed.
This sacrifices a small amount of precision in the adjustment but we
avoid erratic behavior of the clock due to the overflow caused if ppb is
very near the maximum adjustment.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7e5d05e18b ]
We need to introduce a new compatible name for the Meson-AXG SoC
in order to support the RMII 100M ethernet PHY, since the PRG_ETH0
register of the dwmac glue layer is changed from previous old SoC.
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 03d9fbc397 ]
The Meson8m2 SoC is a variant of Meson8 with some updates from Meson8b
(such as the Gigabit capable DesignWare MAC).
It is mostly pin compatible with Meson8, only 10 (existing) CBUS pins
get an additional function (four of these are Ethernet RXD2, RXD3, TXD2
and TXD3 which are required when the board uses an RGMII PHY).
The AOBUS pins seem to be identical on Meson8 and Meson8m2.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 486e666136 ]
The use of stack Variable Length Arrays needs to be avoided, as they
can be a vector for stack exhaustion, which can be both a runtime bug
(kernel Oops) or a security flaw (overwriting memory beyond the
stack). Also, in general, as code evolves it is easy to lose track of
how big a VLA can get. Thus, we can end up having runtime failures
that are hard to debug. As part of the directive[1] to remove all VLAs
from the kernel, and build with -Wvla.
Currently driver is using a VLA declared using the number of descriptors. This
array is used to store integer values and is later used as an argument to
`gpiod_set_array_value_cansleep()` This can be avoided by using
`kmalloc_array()` to allocate memory for the array of integer values. Memory is
free'd before return from function.
>From the code it appears that it is safe to sleep so we can use GFP_KERNEL
(based _cansleep() suffix of function `gpiod_set_array_value_cansleep()`.
It can be expected that this patch will result in a small increase in overhead
due to the use of `kmalloc_array()`
[1] https://lkml.org/lkml/2018/3/7/621
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8e142e9e62 ]
DECLARE_TLV_DB_SCALE (alias of SNDRV_CTL_TLVD_DECLARE_DB_SCALE) is used but
tlv.h is not included. This causes build failure when local macro is
defined by comment-out.
This commit fixes the bug. At the same time, the alias macro is replaced
with a destination macro added at a commit 46e860f768 ("ALSA: rename
TLV-related macros so that they're friendly to user applications")
Reported-by: Connor McAdams <conmanx360@gmail.com>
Fixes: 44f0c9782c ('ALSA: hda/ca0132: Add tuning controls')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6290182b2b ]
Since commit 9776d32537 ("net: Move call_fib_rule_notifiers up in
fib_nl_newrule") it is possible to forbid the installation of
unsupported FIB rules.
Have mlxsw return an error for non-default FIB rules in addition to the
existing extack message.
Example:
# ip rule add from 198.51.100.1 table 10
Error: mlxsw_spectrum: FIB rules not supported.
Note that offload is only aborted when non-default FIB rules are already
installed and merely replayed during module initialization.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0ec4ee3c9b ]
sdhci_omap_config_iodelay_pinctrl_state() requires caps and caps2 to be
initialized (speed mode capabilities like UHS/HS200) before it is
invoked. While mmc_of_parse() initializes caps/caps2 if capabilities is
populated in device tree, it will remain uninitialized for capabilities
obtained from SDHCI_CAPABILITIES register.
Fix sdhci_omap_config_iodelay_pinctrl_state() to be used even while
getting the capabilities from SDHCI_CAPABILITIES register by invoking
sdhci_setup_host() before sdhci_omap_config_iodelay_pinctrl_state().
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 509f89652f ]
Commit be7fd3c3a8 ("media: em28xx: Hauppauge DualHD second tuner
functionality") removed the logic with sets the alternate for the DVB
device. Without setting the right alternate, the device won't be
able to submit URBs, and userspace fails with -EMSGSIZE:
ERROR DMX_SET_PES_FILTER failed (PID = 0x2000): 90 Message too long
Tested with Hauppauge HVR-950 model A1C0.
Fixes: be7fd3c3a8 ("media: em28xx: Hauppauge DualHD second tuner functionality")
Cc: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5b19d284f5 ]
pageout() in MM traslates EAGAIN, so calls handle_write_error()
-> mapping_set_error() -> set_bit(AS_EIO, ...).
file_write_and_wait_range() will see EIO error, which is critical
to return value of fsync() followed by atomic_write failure to user.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 08813e0ec1 ]
If device tree is not enabled, of_find_regulator_by_node() should have
a dummy function since the function call is still there.
This is to fix build error after CONFIG_NO_AUTO_INLINE is introduced.
If this option is enabled, GCC will not auto-inline functions that are
not explicitly marked as inline.
In this case (no CONFIG_OF), the copmiler will report error in function
regulator_dev_lookup().
W/O NO_AUTO_INLINE, function of_get_regulator() is auto-inlined and then
the call to of_find_regulator_by_node() is optimized out since
of_get_regulator() always return NULL.
W/ NO_AUTO_INLINE, the return value of of_get_regulator() is a variable
so the call to of_find_regulator_by_node() cannot be optimized out. So
we need a stub of_find_regulator_by_node().
static struct regulator_dev *regulator_dev_lookup(struct device *dev,
const char *supply)
{
struct regulator_dev *r = NULL;
struct device_node *node;
struct regulator_map *map;
const char *devname = NULL;
regulator_supply_alias(&dev, &supply);
/* first do a dt based lookup */
if (dev && dev->of_node) {
node = of_get_regulator(dev, supply);
if (node) {
r = of_find_regulator_by_node(node);
if (r)
return r;
...
Signed-off-by: Changbin Du <changbin.du@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit de7eab301d ]
As the recent swiotlb bug revealed, we seem to have given up the direct
DMA allocation too early and felt back to swiotlb allocation. The reason
is that swiotlb allocator expected that dma_direct_alloc() would try
harder to get pages even below 64bit DMA mask with GFP_DMA32, but the
function doesn't do that but only deals with GFP_DMA case.
This patch adds a similar fallback reallocation with GFP_DMA32 as we've
done with GFP_DMA. The condition is that the coherent mask is smaller
than 64bit (i.e. some address limitation), and neither GFP_DMA nor
GFP_DMA32 is set beforehand.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4f4616ceeb ]
Similar to what we do when we remove a PCI function, set the
QEDF_UNLOADING flag to prevent any requests from being queued while a
vport is being deleted. This prevents any requests from getting stuck
in limbo when the vport is unloaded or deleted.
Fixes the crash:
PID: 106676 TASK: ffff9a436aa90000 CPU: 12 COMMAND: "multipathd"
#0 [ffff9a43567d3550] machine_kexec+522 at ffffffffaca60b2a
#1 [ffff9a43567d35b0] __crash_kexec+114 at ffffffffacb13512
#2 [ffff9a43567d3680] crash_kexec+48 at ffffffffacb13600
#3 [ffff9a43567d3698] oops_end+168 at ffffffffad117768
#4 [ffff9a43567d36c0] no_context+645 at ffffffffad106f52
#5 [ffff9a43567d3710] __bad_area_nosemaphore+116 at ffffffffad106fe9
#6 [ffff9a43567d3760] bad_area+70 at ffffffffad107379
#7 [ffff9a43567d3788] __do_page_fault+1247 at ffffffffad11a8cf
#8 [ffff9a43567d37f0] do_page_fault+53 at ffffffffad11a915
#9 [ffff9a43567d3820] page_fault+40 at ffffffffad116768
[exception RIP: qedf_init_task+61]
RIP: ffffffffc0e13c2d RSP: ffff9a43567d38d0 RFLAGS: 00010046
RAX: 0000000000000000 RBX: ffffbe920472c738 RCX: ffff9a434fa0e3e8
RDX: ffff9a434f695280 RSI: ffffbe920472c738 RDI: ffff9a43aa359c80
RBP: ffff9a43567d3950 R8: 0000000000000c15 R9: ffff9a3fb09b9880
R10: ffff9a434fa0e3e8 R11: ffff9a43567d35ce R12: 0000000000000000
R13: ffff9a434f695280 R14: ffff9a43aa359c80 R15: ffff9a3fb9e005c0
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 495ac33a3b ]
With a later commit an instance of the struct device will be added to
struct genpd and with that the size of the struct tegra_powergate will
be over 1024 bytes. That generates following warning:
drivers/soc/tegra/pmc.c:579:1: warning: the frame size of 1200 bytes is larger than 1024 bytes [-Wframe-larger-than=]
Avoid such warnings by allocating the structure dynamically.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9413532788 ]
As a unconstrained command, a command can be sent to SATA disk even if
SATA disk status is BUSY, ERR or DRQ.
If an ATA reset assert is successful but ATA reset de-assert fails, then
it will retry the reset de-assert. If reset de- assert retry is
successful, we think it is okay to probe the device but actually it
still has Err status.
Apparently we need to retry the ATA reset assertion and de- assertion
instead for this mentioned scenario.
As such, we config ATA reset assert as a constrained command, if ATA
reset de-assert fails, then ATA reset de-assert retry will also
fail. Then we will retry the proper process of ATA reset assert and
de-assert again.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9899e4d352 ]
In tw_chrdev_ioctl(), the length of the data buffer is firstly copied
from the userspace pointer 'argp' and saved to the kernel object
'data_buffer_length'. Then a security check is performed on it to make
sure that the length is not more than 'TW_MAX_IOCTL_SECTORS *
512'. Otherwise, an error code -EINVAL is returned. If the security
check is passed, the entire ioctl command is copied again from the
'argp' pointer and saved to the kernel object 'tw_ioctl'. Then, various
operations are performed on 'tw_ioctl' according to the 'cmd'. Given
that the 'argp' pointer resides in userspace, a malicious userspace
process can race to change the buffer length between the two
copies. This way, the user can bypass the security check and inject
invalid data buffer length. This can cause potential security issues in
the following execution.
This patch checks for capable(CAP_SYS_ADMIN) in tw_chrdev_open() to
avoid the above issues.
Signed-off-by: Wenwen Wang <wang6495@umn.edu>
Acked-by: Adam Radford <aradford@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c9318a3e02 ]
In twa_chrdev_ioctl(), the ioctl driver command is firstly copied from
the userspace pointer 'argp' and saved to the kernel object
'driver_command'. Then a security check is performed on the data buffer
size indicated by 'driver_command', which is
'driver_command.buffer_length'. If the security check is passed, the
entire ioctl command is copied again from the 'argp' pointer and saved
to the kernel object 'tw_ioctl'. Then, various operations are performed
on 'tw_ioctl' according to the 'cmd'. Given that the 'argp' pointer
resides in userspace, a malicious userspace process can race to change
the buffer size between the two copies. This way, the user can bypass
the security check and inject invalid data buffer size. This can cause
potential security issues in the following execution.
This patch checks for capable(CAP_SYS_ADMIN) in twa_chrdev_open()t o
avoid the above issues.
Signed-off-by: Wenwen Wang <wang6495@umn.edu>
Acked-by: Adam Radford <aradford@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 707e7e9660 ]
The current code already forwards the VF MAC address to the PF, except
in one case. If the VF driver gets a valid MAC address from the firmware
during probe time, it will not forward the MAC address to the PF,
incorrectly assuming that the PF already knows the MAC address. This
causes "ip link show" to show zero VF MAC addresses for this case.
This assumption is not correct. Newer firmware remembers the VF MAC
address last used by the VF and provides it to the VF driver during
probe. So we need to always forward the VF MAC address to the PF.
The forwarded MAC address may now be the PF assigned MAC address and so we
need to make sure we approve it for this case.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dac0490718 ]
Only non-NPAR PFs need to actively check and manage unsupported link
speeds. NPAR functions and VFs do not control the link speed and
should skip the unsupported speed detection logic, to avoid warning
messages from firmware rejecting the unsupported firmware calls.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2b999ba899 ]
When computing the bitrate using values read from an SFP module EEPROM,
we use the nominal BR plus BR,min and BR,max to determine the
boundaries. But in some cases BR,min and BR,max aren't provided, which
led the SFP code to end up having the nominal value for both the minimum
and maximum bitrate values. When using a passive cable, the nominal
value should be used as the maximum one, and there is no minimum one
so we should use 0.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3c0a83b14e ]
The s390 CPU measurement facility sampling mode supports basic entries
and diagnostic entries. Each entry has a valid bit to indicate the
status of the entry as valid or invalid.
This bit is bit 31 in the diagnostic entry, but the bit mask definition
refers to bit 30.
Fix this by making the reserved field one bit larger.
Fixes: 7e75fc3ff4 ("s390/cpum_sf: Add raw data sampling to support the diagnostic-sampling function")
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Reviewed-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 77715b7ddb ]
The CPU Measurement sampling facility creates a trailer entry for each
Sample-Data-Block of stored samples. The trailer entry contains the sizes
(in bytes) of the stored sampling types:
- basic-sampling data entry size
- diagnostic-sampling data entry size
Both sizes are 2 bytes long.
This patch changes the trailer entry definition to reflect this.
Fixes: fcc77f5073 ("s390/cpum_sf: Atomically reset trailer entry fields of sample-data-blocks")
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Reviewed-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9c4a121e82 ]
Add support for the BCM43364 chipset via an SDIO interface, as used in
e.g. the Murata 1FX module.
The BCM43364 uses the same firmware as the BCM43430 (which is already
included), the only difference is the omission of Bluetooth.
However, the SDIO_ID for the BCM43364 is 02D0:A9A4, giving it a MODALIAS
of sdio:c00v02D0dA9A4, which doesn't get recognised and hence doesn't
load the brcmfmac module. Adding the 'A9A4' ID in the appropriate place
triggers the brcmfmac driver to load, and then correctly use the
firmware file 'brcmfmac43430-sdio.bin'.
Signed-off-by: Sean Lanigan <sean@lano.id.au>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a75bbe71a2 ]
Per ONFI specification (Rev. 4.0), if the CRC of the first parameter page
read is not valid, the host should read redundant parameter page copies.
Fix FSL NAND driver to read the two redundant copies which are mandatory
in the specification.
Signed-off-by: Jane Wan <Jane.Wan@nokia.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 01affb000e ]
The use of a hard coded i2c address breaks the creation of the
second tuner in DualHD 01595 models. The issue is compounded
by lack of any error message stating that a driver failed
initialization. Use addr, which contains the correct address
for each tuner.
Fixes: ad32495b15 ("media: em28xx-dvb: simplify DVB module probing logic")
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d3a67f2747 ]
The renesas-ceu driver intializes the desired mbus_format at 'complete'
time, inspecting the supported subdevice ones, and tuning some
parameters to produce the requested memory format from what the sensor
can produce. Although, the initially selected mbus_format was not
provided to the subdevice during set_fmt and try_fmt operations,
providing instead a '0' mbus format code.
As long as the sensor defaults to a compatible mbus_format when an
invalid code as '0' is provided, capture operations work correctly. If
the subdevice defaults to an unsupported format (eg. some RGB
permutations) capture does not work properly due to a mismatch on the
expected and received image format on the wire.
Fix that by re-using the initially selected mbus_format code during
set_fmt and try_fmt subdevice operation calls.
Tested by printing out the format selection procedure with ov7670
sensor.
Before this patch:
[ 0.866001] ov7670_try_fmt_internal -- Looking for mbus_code 0x0000
[ 0.870882] ov7670_try_fmt_internal -- Try mbus_code 0x2008
[ 0.876336] ov7670_try_fmt_internal -- Try mbus_code 0x1002
[ 0.881387] ov7670_try_fmt_internal -- Try mbus_code 0x1008
[ 0.886537] ov7670_try_fmt_internal -- Try mbus_code 0x3001
[ 0.891584] ov7670_try_fmt_internal -- mbus_code defaulted to 0x2008
With this patch applied:
[ 0.867015] ov7670_try_fmt_internal -- Looking for mbus_code 0x2008
[ 0.873205] ov7670_try_fmt_internal -- Try mbus_code 0x2008: match
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0cc4655cb5 ]
This issue was reported by a user who downloaded a corrupt saa7164
firmware, then went looking for a valid xc5000 firmware to fix the
error displayed...but the device in question has no xc5000, thus after
much effort, the wild goose chase eventually led to a support call.
The xc5000 has nothing to do with saa7164 (as far as I can tell),
so replace the string with saa7164 as well as give a meaningful
hint on the firmware mismatch.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c975e472ec ]
The Point of View mobii wintab p800w Bay Trail tablet comes with a Crystal
Cove PMIC, yet uses the LPSS PWM for backlight control, rather then the
Crystal Cove's PWM, so we need to call pwm_add_table() to add a
pwm_backlight mapping for the LPSS pwm despite there being an INT33FD
ACPI device present.
On all Bay Trail devices the _HRV object of the INT33FD ACPI device
will normally return 2, to indicate the Bay Trail variant of the CRC
PMIC is present, except on this tablet where _HRV is 0xffff. I guess this
is a hack to make the windows Crystal Cove PWM driver not bind.
Out of the 44 DSTDs with an INT33FD device in there which I have (from
different model devices) only the pov mobii wintab p800w uses 0xffff for
the HRV.
The byt_pwm_setup code calls acpi_dev_present to check for the presence
of a INT33FD ACPI device which indicates that a CRC PMIC is present and
if the INT33FD ACPI device is present then byt_pwm_setup will not add
a pwm_backlight mapping for the LPSS pwm, so that the CRC PWM will get
used instead.
acpi_dev_present has a hrv parameter, this commit make us pass 2 instead
of -1, so that things still match on normal tablets, but on this special
case with its _HRV of 0xffff, the check will now fail so that the
pwm_backlight mapping for the LPSS pwm gets added fixing backlight
brightness control on this device.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 804689ad2d ]
For failed commands with valid sense data (e.g. NCQ commands),
scsi_check_sense() is used in ata_analyze_tf() to determine if the
command can be retried. In such case, rely on this decision and ignore
the command error mask based decision done in ata_worth_retry().
This fixes useless retries of commands such as unaligned writes on zoned
disks (TYPE_ZAC).
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit daab3349ad ]
We are not releasing the link GPIO descriptor with gpiod_put() which results in
subsequent probing to get -EBUSY when calling fwnode_get_named_gpiod(). Fix this
by doing the release in phylink_destroy().
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8a22a3e1e7 ]
Inclusion of include/dma-iommu.h when CONFIG_IOMMU_DMA is not selected
results in the following splat:
In file included from drivers/irqchip/irq-gic-v3-mbi.c:20:0:
./include/linux/dma-iommu.h:95:69: error: unknown type name ‘dma_addr_t’
static inline int iommu_get_msi_cookie(struct iommu_domain *domain, dma_addr_t base)
^~~~~~~~~~
./include/linux/dma-iommu.h:108:74: warning: ‘struct list_head’ declared inside parameter list will not be visible outside of this definition or declaration
static inline void iommu_dma_get_resv_regions(struct device *dev, struct list_head *list)
^~~~~~~~~
scripts/Makefile.build:312: recipe for target 'drivers/irqchip/irq-gic-v3-mbi.o' failed
Fix it by including linux/types.h.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Rob Herring <robh@kernel.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lkml.kernel.org/r/20180508121438.11301-5-marc.zyngier@arm.com
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c79756cb5f ]
In commit bbc4e7d273 ("i40e: fix race condition with PTP_TX_IN_PROGRESS
bits") we modified the code which handles Tx timestamps so that we would
clear the progress bit as soon as possible.
A later commit 0bc0706b46 ("i40e: check for Tx timestamp timeouts during
watchdog") introduced similar code for detecting and handling cleanup of
a blocked Tx timestamp. This code did not use the same pattern for cleaning
up the skb.
Update this code to wait to free the skb until after the bit lock is
free, by first setting the ptp_tx_skb to NULL and clearing the lock.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 77dd4bd0c0 ]
Single child nodes in OF graph don't need an address and now dtc will
warn about this:
Warning (graph_child_address): /soc/aips@50000000/ldb@53fa8008/lvds-channel@0: graph node has single child node 'port@0', #address-cells/#size-cells are not necessary
Since the LDB should always have an output port, fix the warning by
adding the output port, 2, to the DT.
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 50808bfcc1 ]
Function nvmem_reg_read can return a non zero value indicating an error.
This returned value must be read and error propagated to
nvmem_cell_prepare_write_buffer. Silence the following gcc warning (W=1):
drivers/nvmem/core.c:1093:9: warning: variable 'rc' set but
not used [-Wunused-but-set-variable]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 57a66497e1 ]
The PMU node references two interrupts, but lacks the interrupt-affinity
property, which is required in that case:
hw perfevents: no interrupt-affinity property for /pmu, guessing.
Add the missing property to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7207b94754 ]
The PMU node references two interrupts, but lacks the interrupt-affinity
property, which is required in that case:
hw perfevents: no interrupt-affinity property for /pmu, guessing.
Add the missing property to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e95b8e718f ]
Since commit 83a86fbb5b ("irqchip/gic: Loudly complain about the use of IRQ_TYPE_NONE")
kernel is complaining about the IRQ_TYPE_NONE usage which shouldn't
be used.
Use IRQ_TYPE_LEVEL_HIGH instead.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fd827d0ec8 ]
Since commit 83a86fbb5b ("irqchip/gic: Loudly complain about the use of IRQ_TYPE_NONE")
kernel is complaining about the IRQ_TYPE_NONE usage which shouldn't
be used.
Use IRQ_TYPE_LEVEL_HIGH instead.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 54b5172087 ]
When the "poweroff" command is executed after wowlan enabled, we have
observed a system crash. In the system "poweroff" sequence, network-manager
is sent to inactive state by cleaning up the network interfaces, using
rsi_mac80211_remove_interface() and when driver tries to access those
network interfaces in rsi_wowlan_config() which was invoked by SDIO
shutdown, results in a crash. Added a NULL check before accessing the
network interfaces in rsi_wowlan_config().
Signed-off-by: Sanjay Kumar Konduri <sanjay.konduri@redpinesignals.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Sushant Kumar Mishra <sushant.mishra@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b3a81b6c4f ]
On many Chromebooks touch devices are multi-sourced; the components are
electrically compatible and one can be freely swapped for another without
changing the OS image or firmware.
To avoid bunch of scary messages when device is not actually present in the
system let's try testing basic communication with it and if there is no
response terminate probe early with -ENXIO.
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9dcb3df428 ]
The interrupt controller inside the Wii's Hollywood chip is connected to
two masters, the "Broadway" PowerPC and the "Starlet" ARM926, each with
their own interrupt status and mask registers.
When booting the Wii with mini[1], interrupts from the SD card
controller (IRQ 7) are handled by the ARM, because mini provides SD
access over IPC. Linux however can't currently use or disable this IPC
service, so both sides try to handle IRQ 7 without coordination.
Let's instead make sure that all interrupts that are unmasked on the PPC
side are masked on the ARM side; this will also make sure that Linux can
properly talk to the SD card controller (and potentially other devices).
If access to a device through IPC is desired in the future, interrupts
from that device should not be handled by Linux directly.
[1]: https://github.com/lewurm/mini
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e02637e97d ]
DMA_VIRT_OPS requires that dma_addr_t is at least as wide as a
pointer, which is expressed as a dependency on !64BIT ||
ARCH_DMA_ADDR_T_64BIT.
For parisc64 this is not true, and if these IB modules are enabled,
kconfig warns:
WARNING: unmet direct dependencies detected for DMA_VIRT_OPS
Depends on [n]: HAS_DMA [=y] && (!64BIT [=y] || ARCH_DMA_ADDR_T_64BIT)
Selected by [m]:
- INFINIBAND_RDMAVT [=m] && INFINIBAND [=m] && 64BIT [=y] && PCI [=y]
- RDMA_RXE [=m] && INET [=y] && PCI [=y] && INFINIBAND [=m]
Add dependencies to fix this.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7a47f20eb1 ]
The method struct drm_connector_helper_funcs::mode_valid is defined
as returning an 'enum drm_mode_status' but the driver implementation
for this method uses an 'int' for it.
Fix this by using 'enum drm_mode_status' in the driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a2a330ad66 ]
This patch is in continuation to the
"843e3c7 drm/amd/display: defer modeset check in dm_update_planes_state"
where we started to eliminate the dependency on
DRM_MODE_ATOMIC_ALLOW_MODESET to be set by the user space,
which as such is not mandatory.
After deferring, this patch eliminates the dependency on the flag
for overlay planes.
This has to be done in stages as its a pretty complex and requires thorough
testing before we free primary planes as well from dependency on modeset
flag.
V2: Simplified the plane type check.
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 06a574c7ef ]
Current Sound is using simple-audio-card which can't support HDMI.
To use HDMI sound, we need to use audio-graph-card.
But, one note is that r8a7795 has 2 HDMI ports, but r8a7796 has 1.
Because of this mismatch, supporting HDMI on salvator-common is
impossible.
Thus, this patch exchange sound card to audio-graph-card and keep
supporting ak4613 as 1st sound node.
r8a7795/r8a7796 salvator-x{s} need to add HDMI sound individually.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Nguyen Viet Dung <nv-dung@jinso.co.jp>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1cfc63b5ae ]
When waiting for a cacheline to change state in cmpwait, we may immediately
wake-up the first time around the outer loop if the event register was
already set (for example, because of the event stream).
Avoid these spurious wakeups by explicitly clearing the event register
before loading the cacheline and setting the exclusive monitor.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit db01f7ccfa ]
The register settings for several resolutions aren't used
currently. So, comment them out.
Fix those warnings:
In file included from drivers/staging/media/atomisp/i2c/atomisp-gc2235.c:35:0:
drivers/staging/media/atomisp/i2c/gc2235.h:340:32: warning: 'gc2235_960_640_30fps' defined but not used [-Wunused-const-variable=]
static struct gc2235_reg const gc2235_960_640_30fps[] = {
^~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/gc2235.h:287:32: warning: 'gc2235_1296_736_30fps' defined but not used [-Wunused-const-variable=]
static struct gc2235_reg const gc2235_1296_736_30fps[] = {
^~~~~~~~~~~~~~~~~~~~~
In file included from drivers/staging/media/atomisp/i2c/atomisp-ov2722.c:35:0:
drivers/staging/media/atomisp/i2c/ov2722.h:999:32: warning: 'ov2722_720p_30fps' defined but not used [-Wunused-const-variable=]
static struct ov2722_reg const ov2722_720p_30fps[] = {
^~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2722.h:787:32: warning: 'ov2722_1M3_30fps' defined but not used [-Wunused-const-variable=]
static struct ov2722_reg const ov2722_1M3_30fps[] = {
^~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2722.h:476:32: warning: 'ov2722_VGA_30fps' defined but not used [-Wunused-const-variable=]
static struct ov2722_reg const ov2722_VGA_30fps[] = {
^~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2722.h:367:32: warning: 'ov2722_480P_30fps' defined but not used [-Wunused-const-variable=]
static struct ov2722_reg const ov2722_480P_30fps[] = {
^~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2722.h:257:32: warning: 'ov2722_QVGA_30fps' defined but not used [-Wunused-const-variable=]
static struct ov2722_reg const ov2722_QVGA_30fps[] = {
^~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/atomisp-ov2680.c: In function '__ov2680_set_exposure':
In file included from drivers/staging/media/atomisp/i2c/atomisp-ov2680.c:35:0:
At top level:
drivers/staging/media/atomisp/i2c/ov2680.h:736:33: warning: 'ov2680_1616x1082_30fps' defined but not used [-Wunused-const-variable=]
static struct ov2680_reg const ov2680_1616x1082_30fps[] = {
^~~~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2680.h:649:33: warning: 'ov2680_1456x1096_30fps' defined but not used [-Wunused-const-variable=]
static struct ov2680_reg const ov2680_1456x1096_30fps[]= {
^~~~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2680.h:606:33: warning: 'ov2680_1296x976_30fps' defined but not used [-Wunused-const-variable=]
static struct ov2680_reg const ov2680_1296x976_30fps[] = {
^~~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2680.h:563:33: warning: 'ov2680_720p_30fps' defined but not used [-Wunused-const-variable=]
static struct ov2680_reg const ov2680_720p_30fps[] = {
^~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2680.h:520:33: warning: 'ov2680_800x600_30fps' defined but not used [-Wunused-const-variable=]
static struct ov2680_reg const ov2680_800x600_30fps[] = {
^~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2680.h:475:33: warning: 'ov2680_720x592_30fps' defined but not used [-Wunused-const-variable=]
static struct ov2680_reg const ov2680_720x592_30fps[] = {
^~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2680.h:433:33: warning: 'ov2680_656x496_30fps' defined but not used [-Wunused-const-variable=]
static struct ov2680_reg const ov2680_656x496_30fps[] = {
^~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2680.h:389:33: warning: 'ov2680_QVGA_30fps' defined but not used [-Wunused-const-variable=]
static struct ov2680_reg const ov2680_QVGA_30fps[] = {
^~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2680.h:346:33: warning: 'ov2680_CIF_30fps' defined but not used [-Wunused-const-variable=]
static struct ov2680_reg const ov2680_CIF_30fps[] = {
^~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2680.h:301:33: warning: 'ov2680_QCIF_30fps' defined but not used [-Wunused-const-variable=]
static struct ov2680_reg const ov2680_QCIF_30fps[] = {
^~~~~~~~~~~~~~~~~
In file included from drivers/staging/media/atomisp/i2c/ov5693/atomisp-ov5693.c:36:0:
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:988:32: warning: 'ov5693_1424x1168_30fps' defined but not used [-Wunused-const-variable=]
static struct ov5693_reg const ov5693_1424x1168_30fps[] = {
^~~~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:954:32: warning: 'ov5693_2592x1944_30fps' defined but not used [-Wunused-const-variable=]
static struct ov5693_reg const ov5693_2592x1944_30fps[] = {
^~~~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:889:32: warning: 'ov5693_2592x1456_30fps' defined but not used [-Wunused-const-variable=]
static struct ov5693_reg const ov5693_2592x1456_30fps[] = {
^~~~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:862:32: warning: 'ov5693_1940x1096' defined but not used [-Wunused-const-variable=]
static struct ov5693_reg const ov5693_1940x1096[] = {
^~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:796:32: warning: 'ov5693_1636p_30fps' defined but not used [-Wunused-const-variable=]
static struct ov5693_reg const ov5693_1636p_30fps[] = {
^~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:758:32: warning: 'ov5693_1296x736' defined but not used [-Wunused-const-variable=]
static struct ov5693_reg const ov5693_1296x736[] = {
^~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:730:32: warning: 'ov5693_976x556' defined but not used [-Wunused-const-variable=]
static struct ov5693_reg const ov5693_976x556[] = {
^~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:672:32: warning: 'ov5693_736x496' defined but not used [-Wunused-const-variable=]
static struct ov5693_reg const ov5693_736x496[] = {
^~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:643:32: warning: 'ov5693_192x160' defined but not used [-Wunused-const-variable=]
static struct ov5693_reg const ov5693_192x160[] = {
^~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:616:32: warning: 'ov5693_368x304' defined but not used [-Wunused-const-variable=]
static struct ov5693_reg const ov5693_368x304[] = {
^~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:587:32: warning: 'ov5693_336x256' defined but not used [-Wunused-const-variable=]
static struct ov5693_reg const ov5693_336x256[] = {
^~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:540:32: warning: 'ov5693_1296x976' defined but not used [-Wunused-const-variable=]
static struct ov5693_reg const ov5693_1296x976[] = {
^~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:509:32: warning: 'ov5693_654x496' defined but not used [-Wunused-const-variable=]
static struct ov5693_reg const ov5693_654x496[] = {
^~~~~~~~~~~~~~
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e5c0680fd2 ]
drivers/staging/media/atomisp/i2c/atomisp-ov2680.c: In function ‘__ov2680_set_exposure’:
drivers/staging/media/atomisp/i2c/atomisp-ov2680.c:400:10: warning: variable ‘hts’ set but not used [-Wunused-but-set-variable]
u16 vts,hts;
^~~
drivers/staging/media/atomisp/i2c/atomisp-ov2680.c: In function ‘ov2680_detect’:
drivers/staging/media/atomisp/i2c/atomisp-ov2680.c:1164:5: warning: variable ‘revision’ set but not used [-Wunused-but-set-variable]
u8 revision;
^~~~~~~~
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit be8d8cdb8e ]
When hclge_ae_start is called, hdev->hw.mac.link may be set
to one after up/down multi-times, which does not correspond to
the link state of netdev when the netdev is up.
This fixes it by setting hdev->hw.mac.link to zero when
hclge_ae_start is called.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c6213eb1ae ]
This fixes klockworks warnings: Pointer 'dev' returned from call to
function 'bus_find_device' at line 179 may be NULL and will be dereferenced
at line 181.
cpsw-phy-sel.c:179: 'dev' is assigned the return value from function 'bus_find_device'.
bus.c:342: 'bus_find_device' explicitly returns a NULL value.
cpsw-phy-sel.c:181: 'dev' is dereferenced by passing argument 1 to function 'dev_get_drvdata'.
device.h:1024: 'dev' is passed to function 'dev_get_drvdata'.
device.h:1026: 'dev' is explicitly dereferenced.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
[nsekhar@ti.com: add an error message, fix return path]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 56abbf8ad7 ]
The generic IRQ handling code ensures that an interrupt handler runs with
its interrupt masked or disabled. If the interrupt is level-triggered, the
interrupt handler must tell its device to stop asserting the interrupt
before returning. If it doesn't, we will immediately take the interrupt
again when the handler returns and the generic code unmasks the interrupt.
The driver doesn't know whether its interrupt is edge- or level-triggered,
so it must clear its interrupt source directly in its interrupt handler.
Previously we cleared the DPC interrupt status in the bottom half, i.e., in
deferred work, which can cause an interrupt storm if the DPC interrupt
happens to be level-triggered, e.g., if we're using INTx instead of MSI.
Clear the DPC interrupt status bit in the interrupt handler, not in the
deferred work.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7a2148dfda ]
The current code decrements the timeout counter i and the end of
each loop i is incremented, so the check for timeout will always
be false and hence the timeout mechanism is just a dead code path.
Potentially, if the RD_READY bit is not set, we could end up in
an infinite loop.
Fix this so the timeout starts from 1000 and decrements to zero,
if at the end of the loop i is zero we have a timeout condition.
Detected by CoverityScan, CID#1324008 ("Logically dead code")
Fixes: ccfc97bdb5 ("[media] smiapp: Add driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f40e1590c5 ]
The IOVA API uses a memory cache to allocate IOVA nodes from. To make
sure that this cache is available, obtain a reference to it and release
the reference when the cache is no longer needed.
On 64-bit ARM this is hidden by the fact that the DMA mapping API gets
that reference and never releases it. On 32-bit ARM, this is papered
over by the Tegra DRM driver (the sole user of the host1x API requiring
the cache) acquiring a reference to the IOVA cache for its own purposes.
However, there may be additional users of this API in the future, so fix
this upfront to avoid surprises.
Fixes: 404bfb78da ("gpu: host1x: Add IOMMU support")
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b33d10624f ]
Current handle_read_error() function calls fix_read_error()
only if md device is RW and rdev does not include FailFast flag.
It does not handle a read error from a RW device including
FailFast flag.
I am not sure it is intended. But I found that write IO error
sets rdev faulty. The md module should handle the read IO error and
write IO error equally. So I think read IO error should set rdev faulty.
Signed-off-by: Gioh Kim <gi-oh.kim@profitbricks.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0b01fd3d40 ]
If is_enabled() is not defined, regulator core will assume
this regulator is already enabled, then it can NOT be really
enabled after disabled.
Based on Li Jun's patch from the NXP kernel tree.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e6000a438e ]
The IRQ is requested before the struct rtc is allocated and registered, but
this struct is used in the IRQ handler. This may lead to a NULL pointer
dereference.
Switch to devm_rtc_allocate_device/rtc_register_device to allocate the rtc
before requesting the IRQ.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4f2fc25c0f ]
Newer HW doesn't appear to send this event, which will cause long delays
in runlist updates if they don't complete immediately.
RM doesn't use these events anywhere, and an NVGPU commit message notes
that polling is the preferred method even on HW that supports the event.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 19ca10d82e ]
We previously only did this for push buffers, but an upcoming patch will
need to attach fences to all VMAs to resolve another issue.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 11e451e740 ]
Fences attached to deferred client work items now originate from channels
belonging to the client, meaning we can be certain they've been signalled
before we destroy a client.
This closes a race that could happen if the dma_fence_wait_timeout() call
didn't succeed. When the fence was later signalled, a use-after-free was
possible.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2e3611e954 ]
The device can set the exception event bit in one of the response UPIU,
for example to notify the need for urgent BKOPs operation. In such a
case, the host driver calls ufshcd_exception_event_handler to handle
this notification. When trying to check the exception event status (for
finding the cause for the exception event), the device may be busy with
additional SCSI commands handling and may not respond within the 100ms
timeout.
To prevent that, we need to block SCSI commands during handling of
exception events and allow retransmissions of the query requests, in
case of timeout.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Asutosh Das <asutoshd@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b334456ec2 ]
Vendor specific setup_clocks ops may depend on clocks managed by ufshcd
driver so if the vendor specific setup_clocks callback is called when
the required clocks are turned off, it results into unclocked register
access.
This change make sure that required clocks are enabled before vendor
specific setup_clocks callback is called.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 62c8a069b5 ]
Marvell PPv2 Header Parser sets some bits in the 'result_info' field in
each lookup iteration, to identify different packet attributes such as
DSA / VLAN tag, protocol infos, etc. This is used in further
classification stages in the controller.
It's the DSA tag detection entry that is in charge of detecting when there
is a single VLAN tag.
This commits adds the missing update of the result_info in this case.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 36dd26e0c8 ]
Improve fscrypt read performance by switching the decryption workqueue
from bound to unbound. With the bound workqueue, when multiple bios
completed on the same CPU, they were decrypted on that same CPU. But
with the unbound queue, they are now decrypted in parallel on any CPU.
Although fscrypt read performance can be tough to measure due to the
many sources of variation, this change is most beneficial when
decryption is slow, e.g. on CPUs without AES instructions. For example,
I timed tarring up encrypted directories on f2fs. On x86 with AES-NI
instructions disabled, the unbound workqueue improved performance by
about 25-35%, using 1 to NUM_CPUs jobs with 4 or 8 CPUs available. But
with AES-NI enabled, performance was unchanged to within ~2%.
I also did the same test on a quad-core ARM CPU using xts-speck128-neon
encryption. There performance was usually about 10% better with the
unbound workqueue, bringing it closer to the unencrypted speed.
The unbound workqueue may be worse in some cases due to worse locality,
but I think it's still the better default. dm-crypt uses an unbound
workqueue by default too, so this change makes fscrypt match.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3c7624d8fc ]
If the hns3 driver has been built into kernel and then loaded with
the same driver which built as KLM, it may trigger an error like
below:
[ 20.009555] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version
[ 20.016789] hns3: Copyright (c) 2017 Huawei Corporation.
[ 20.022100] Error: Driver 'hns3' is already registered, aborting...
[ 23.517397] Unable to handle kernel NULL pointer dereference at virtual address 00000000
...
[ 23.691583] Process insmod (pid: 1982, stack limit = 0x00000000cd5f21cb)
[ 23.698270] Call trace:
[ 23.700705] __list_del_entry_valid+0x2c/0xd8
[ 23.705049] hnae3_unregister_client+0x68/0xa8
[ 23.709487] hns3_init_module+0x98/0x1000 [hns3]
[ 23.714093] do_one_initcall+0x5c/0x170
[ 23.717918] do_init_module+0x64/0x1f4
[ 23.721654] load_module+0x1d14/0x24b0
[ 23.725390] SyS_init_module+0x158/0x208
[ 23.729300] el0_svc_naked+0x30/0x34
This patch fixes it by adding module version info.
Fixes: 38caee9d3e ("net: hns3: Add support of the HNAE3 framework")
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit eddf04626d ]
When vf module is loading, the cmd queue initialization should
happen before misc interrupt initialization, otherwise the misc
interrupt handle will cause using uninitialized cmd queue problem.
There is also the same issue when vf module is unloading.
This patch fixes it by adjusting the location of some function.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7e48e23a1f ]
If pm_runtime_get_sync() fails we should call pm_runtime_put_noidle().
This is probably not a critical fix as we should only hit this when
things are broken elsewhere.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1898eb61fb ]
The ARM CCN PMU driver uses dev_warn() to complain about parameters in
the user-provided perf_event_attr. This means that under normal
operation (e.g. a single invocation of the perf tool), a number of
messages warnings may be logged to dmesg.
Tools may issue multiple syscalls to probe for feature support, and
multiple applications (from multiple users) can attempt to open events
simultaneously, so this is not very helpful, even if a user happens to
have access to dmesg. Worse, this can push important information out of
the dmesg ring buffer, and can significantly slow down syscall fuzzers,
vastly increasing the time it takes to find critical bugs.
Demote the dev_warn() instances to dev_dbg(), as is the case for all
other PMU drivers under drivers/perf/. Users who wish to debug PMU event
initialisation can enable dynamic debug to receive these messages.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 408fec36a1 ]
Currently we request control of native PCIe hotplug unconditionally.
Native PCIe hotplug events are handled by the pciehp driver, and if it is
not enabled those events will be lost.
Request control of native PCIe hotplug only if the pciehp driver is
enabled, so we will actually handle native PCIe hotplug events.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4ea69b2fd6 ]
For multi-function programs, loading the address of a callee
function to a register requires emitting instructions whose
count varies from one to five depending on the nature of the
address.
Since we come to know of the callee's address only before the
extra pass, the number of instructions required to load this
address may vary from what was previously generated. This can
make the JITed image grow or shrink.
To avoid this, we should generate a constant five-instruction
when loading function addresses by padding the optimized load
sequence with NOPs.
Signed-off-by: Sandipan Das <sandipan@linux.vnet.ibm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4d56a76ead ]
Currently, for multi-function programs, we cannot get the JITed
instructions using the bpf system call's BPF_OBJ_GET_INFO_BY_FD
command. Because of this, userspace tools such as bpftool fail
to identify a multi-function program as being JITed or not.
With the JIT enabled and the test program running, this can be
verified as follows:
# cat /proc/sys/net/core/bpf_jit_enable
1
Before applying this patch:
# bpftool prog list
1: kprobe name foo tag b811aab41a39ad3d gpl
loaded_at 2018-05-16T11:43:38+0530 uid 0
xlated 216B not jited memlock 65536B
...
# bpftool prog dump jited id 1
no instructions returned
After applying this patch:
# bpftool prog list
1: kprobe name foo tag b811aab41a39ad3d gpl
loaded_at 2018-05-16T12:13:01+0530 uid 0
xlated 216B jited 308B memlock 65536B
...
# bpftool prog dump jited id 1
0: nop
4: nop
8: mflr r0
c: std r0,16(r1)
10: stdu r1,-112(r1)
14: std r31,104(r1)
18: addi r31,r1,48
1c: li r3,10
...
Signed-off-by: Sandipan Das <sandipan@linux.vnet.ibm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a86caa9ba5 ]
Sven Eckelmann reported an issue with the current IPQ4019 pinctrl.
Setting up any gpio-hog in the device-tree for his device would
"kill the bootup completely":
| [ 0.477838] msm_serial 78af000.serial: could not find pctldev for node /soc/pinctrl@1000000/serial_pinmux, deferring probe
| [ 0.499828] spi_qup 78b5000.spi: could not find pctldev for node /soc/pinctrl@1000000/spi_0_pinmux, deferring probe
| [ 1.298883] requesting hog GPIO enable USB2 power (chip 1000000.pinctrl, offset 58) failed, -517
| [ 1.299609] gpiochip_add_data: GPIOs 0..99 (1000000.pinctrl) failed to register
| [ 1.308589] ipq4019-pinctrl 1000000.pinctrl: Failed register gpiochip
| [ 1.316586] msm_serial 78af000.serial: could not find pctldev for node /soc/pinctrl@1000000/serial_pinmux, deferring probe
| [ 1.322415] spi_qup 78b5000.spi: could not find pctldev for node /soc/pinctrl@1000000/spi_0_pinmux, deferri
This was also verified on a RT-AC58U (IPQ4018) which would
no longer boot, if a gpio-hog was specified. (Tried forcing
the USB LED PIN (GPIO0) to high.).
The problem is that Pinctrl+GPIO registration is currently
peformed in the following order in pinctrl-msm.c:
1. pinctrl_register()
2. gpiochip_add()
3. gpiochip_add_pin_range()
The actual error code -517 == -EPROBE_DEFER is coming from
pinctrl_get_device_gpio_range(), which is called through:
gpiochip_add
of_gpiochip_add
of_gpiochip_scan_gpios
gpiod_hog
gpiochip_request_own_desc
__gpiod_request
chip->request
gpiochip_generic_request
pinctrl_gpio_request
pinctrl_get_device_gpio_range
pinctrl_get_device_gpio_range() is unable to find any valid
pin ranges, since nothing has been added to the pinctrldev_list yet.
so the range can't be found, and the operation fails with -EPROBE_DEFER.
This patch fixes the issue by adding the "gpio-ranges" property to
the pinctrl device node of all upstream Qcom SoC. The pin ranges are
then added by the gpio core.
In order to remain compatible with older, existing DTs (and ACPI)
a check for the "gpio-ranges" property has been added to
msm_gpio_init(). This prevents the driver of adding the same entry
to the pinctrldev_list twice.
Reported-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Tested-by: Sven Eckelmann <sven.eckelmann@openmesh.com> [ipq4019]
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2181636471 ]
The device node iterators perform an of_node_get on each iteration, so a
jump out of the loop requires an of_node_put.
The semantic patch that fixes this problem is as follows
(http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
iterator name for_each_child_of_node;
@@
for_each_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
+ of_node_put(child);
? break;
...
}
... when != child
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0921e11e1e ]
According to section 59.2.4 MSIOF Receive Mode Register 1 (SIRMDR1) in
the R-Car Gen3 datasheet Rev.1.00, the value of the SIRMDR1.SYNCAC bit
must match the value of the SITMDR1.SYNCAC bit. However,
sh_msiof_spi_setup() changes only the latter.
Fix this by updating the SIRMDR1 register like the SITMDR1 register,
taking into account register bits that exist in SITMDR1 only.
Reported-by: Renesas BSP team via Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Fixes: 7ff0b53c40 ("spi: sh-msiof: Avoid writing to registers from spi_master.setup()")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 86bf20cb57 ]
This is a fix from reviewing the code, but it looks like it might be
able to lead to an Oops. It affects 32bit systems.
The KVM_MEMORY_ENCRYPT_REG_REGION ioctl uses a u64 for range->addr and
range->size but the high 32 bits would be truncated away on a 32 bit
system. This is harmless but it's also harmless to prevent it.
Then in sev_pin_memory() the "uaddr + ulen" calculation can wrap around.
The wrap around can happen on 32 bit or 64 bit systems, but I was only
able to figure out a problem for 32 bit systems. We would pick a number
which results in "npages" being zero. The sev_pin_memory() would then
return ZERO_SIZE_PTR without allocating anything.
I made it illegal to call sev_pin_memory() with "ulen" set to zero.
Hopefully, that doesn't cause any problems. I also changed the type of
"first" and "last" to long, just for cosmetic reasons. Otherwise on a
64 bit system you're saving "uaddr >> 12" in an int and it truncates the
high 20 bits away. The math works in the current code so far as I can
see but it's just weird.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
[Brijesh noted that the code is only reachable on X86_64.]
Reviewed-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit eae5f709a4 ]
__printf is useful to verify format and arguments. Fix arg mismatch
reported by gcc, remove the following warnings (with W=1):
arch/powerpc/kernel/prom_init.c:1467:31: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1471:31: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1504:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1505:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1506:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1507:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1508:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1509:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1975:39: error: format ‘%lu’ expects argument of type ‘long unsigned int’, but argument 2 has type ‘unsigned int’
arch/powerpc/kernel/prom_init.c:1986:27: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:2567:38: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:2567:46: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 3 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:2569:38: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:2569:46: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 3 has type ‘long unsigned int’
The patch also include arg mismatch fix for case with #define DEBUG_PROM
(warning not listed here).
This patch fix also the following warnings revealed by checkpatch:
WARNING: Prefer using '"%s...", __func__' to using 'alloc_up', this function's name, in a string
#101: FILE: arch/powerpc/kernel/prom_init.c:1235:
+ prom_debug("alloc_up(%lx, %lx)\n", size, align);
and
WARNING: Prefer using '"%s...", __func__' to using 'alloc_down', this function's name, in a string
#138: FILE: arch/powerpc/kernel/prom_init.c:1278:
+ prom_debug("alloc_down(%lx, %lx, %s)\n", size, align,
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5a4b475cf8 ]
Since the value of x is never intended to be read, declare it with gcc
attribute as unused. Fix warning treated as error with W=1:
arch/powerpc/platforms/powermac/bootx_init.c:471:21: error: variable ‘x’ set but not used [-Werror=unused-but-set-variable]
Suggested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f72cf3f1d4 ]
Add a missing prototype for function `note_bootable_part` to silence a
warning treated as error with W=1:
arch/powerpc/platforms/powermac/setup.c:361:12: error: no previous prototype for ‘note_bootable_part’ [-Werror=missing-prototypes]
Suggested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b87a358b4a ]
Add a missing include <platforms/chrp/chrp.h>.
These functions can all be static, make it so. Fix warnings treated as
errors with W=1:
arch/powerpc/platforms/chrp/time.c:41:13: error: no previous prototype for ‘chrp_time_init’ [-Werror=missing-prototypes]
arch/powerpc/platforms/chrp/time.c:66:5: error: no previous prototype for ‘chrp_cmos_clock_read’ [-Werror=missing-prototypes]
arch/powerpc/platforms/chrp/time.c:74:6: error: no previous prototype for ‘chrp_cmos_clock_write’ [-Werror=missing-prototypes]
arch/powerpc/platforms/chrp/time.c:86:5: error: no previous prototype for ‘chrp_set_rtc_time’ [-Werror=missing-prototypes]
arch/powerpc/platforms/chrp/time.c:130:6: error: no previous prototype for ‘chrp_get_rtc_time’ [-Werror=missing-prototypes]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c89ca59322 ]
The header file <linux/syscalls.h> was missing from the includes. Fix the
following warning, treated as error with W=1:
arch/powerpc/kernel/pci_32.c:286:6: error: no previous prototype for ‘sys_pciconfig_iobase’ [-Werror=missing-prototypes]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 699e2302c2 ]
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: ETSI
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9c790f2d23 ]
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: FCC
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2a3169a54b ]
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: ETSI
* 5GHz: ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 667ddac574 ]
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: ETSI
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1ea3986ad2 ]
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: ETSI
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4f183687e3 ]
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't available and
it is still programmed in the EEPROM then it will cause an error and stop
the initialization with:
Invalid EEPROM contents
The current CTL mappings for this regdomain code are:
* 2.4GHz: FCC
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9ba8df0c52 ]
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't available and
it is still programmed in the EEPROM then it will cause an error and stop
the initialization with:
Invalid EEPROM contents
The current CTL mappings for this regdomain code are:
* 2.4GHz: ETSI
* 5GHz: ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 45faf6e096 ]
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't available and
it is still programmed in the EEPROM then it will cause an error and stop
the initialization with:
Invalid EEPROM contents
The current CTL mappings for this regdomain code are:
* 2.4GHz: ETSI
* 5GHz: ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 01fb2994a9 ]
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't available and
it is still programmed in the EEPROM then it will cause an error and stop
the initialization with:
Invalid EEPROM contents
The current CTL mappings for this regdomain code are:
* 2.4GHz: ETSI
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 72cd4cc28e ]
The nvme timeout handling doesn't do anything if the pci channel is
offline, which is the case when recovering from PCI error event, so it
was a bad idea to sync the controller reset in this state. This patch
flushes the reset work in the error_resume callback instead when the
channel is back to online. This keeps AER handling serialized and
can recover from timeouts.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199757
Fixes: cc1d5e749a ("nvme/pci: Sync controller reset for AER slot_reset")
Reported-by: Alex Gagniuc <mr.nuke.me@gmail.com>
Tested-by: Alex Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2e050f00a0 ]
For any failure after nvme_rdma_start_queue in
nvme_rdma_configure_admin_queue, the admin queue will be freed with the
NVME_RDMA_Q_LIVE flag still set. Once nvme_rdma_stop_queue is invoked,
that will cause a use-after-free.
BUG: KASAN: use-after-free in rdma_disconnect+0x1f/0xe0 [rdma_cm]
To fix it, call nvme_rdma_stop_queue for all the failed cases after
nvme_rdma_start_queue.
Signed-off-by: Jianchao Wang <jianchao.w.wang@oracle.com>
Suggested-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 04a512fea3 ]
Two places report an error when a partition header is found to
not contain the right canary value. The error messages do not
properly byte swap the host ids. Fix this, and adjust the format
specificier to match the 16-bit unsigned data type.
Move the error handling for a bad canary value to the end of
qcom_smem_alloc_private(). This avoids some long lines, and
reduces the distraction of handling this unexpected problem.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8fa1a21409 ]
If there is at least one entry in the partition table, but no global
entry, the qcom_smem_set_global_partition() should return an error
just like it does if there are no partition table entries.
It turns out the function still returns an error in this case, but
it waits to do so until it has mistakenly treated the last entry in
the table as if it were the global entry found.
Fix the function to return immediately if no global entry is found
in the table.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7df5ff258b ]
In qmi_handle_init(), a buffer is allocated for to hold messages
received through the handle's socket. Any "normal" messages
(expected by the caller) will have a header prepended, so the
buffer size is adjusted to accomodate that.
The buffer must also be of sufficient size to receive control
messages, so the size is increased if necessary to ensure these
will fit.
Unfortunately the calculation is done wrong, making it possible
for the calculated buffer size to be too small to hold a "normal"
message. Specifically, if:
recv_buf_size > sizeof(struct qrtr_ctrl_pkt) - sizeof(struct qmi_header)
AND
recv_buf_size < sizeof(struct qrtr_ctrl_pkt)
the current logic will use sizeof(struct qrtr_ctrl_pkt) as the
receive buffer size, which is not enough to hold the maximum
"normal" message plus its header. Currently this problem occurs
for (13 < recv_buf_size < 20).
This patch corrects this.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 62fc00a661 ]
The `s2idle_lock' is acquired during suspend while interrupts are
disabled even on RT. The lock is acquired for short sections only.
Make it a RAW lock which avoids "sleeping while atomic" warnings on RT.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ff3d27a048 ]
Under the following case, qgroup rescan can double account cowed tree
blocks:
In this case, extent tree only has one tree block.
-
| transid=5 last committed=4
| btrfs_qgroup_rescan_worker()
| |- btrfs_start_transaction()
| | transid = 5
| |- qgroup_rescan_leaf()
| |- btrfs_search_slot_for_read() on extent tree
| Get the only extent tree block from commit root (transid = 4).
| Scan it, set qgroup_rescan_progress to the last
| EXTENT/META_ITEM + 1
| now qgroup_rescan_progress = A + 1.
|
| fs tree get CoWed, new tree block is at A + 16K
| transid 5 get committed
-
| transid=6 last committed=5
| btrfs_qgroup_rescan_worker()
| btrfs_qgroup_rescan_worker()
| |- btrfs_start_transaction()
| | transid = 5
| |- qgroup_rescan_leaf()
| |- btrfs_search_slot_for_read() on extent tree
| Get the only extent tree block from commit root (transid = 5).
| scan it using qgroup_rescan_progress (A + 1).
| found new tree block beyong A, and it's fs tree block,
| account it to increase qgroup numbers.
-
In above case, tree block A, and tree block A + 16K get accounted twice,
while qgroup rescan should stop when it already reach the last leaf,
other than continue using its qgroup_rescan_progress.
Such case could happen by just looping btrfs/017 and with some
possibility it can hit such double qgroup accounting problem.
Fix it by checking the path to determine if we should finish qgroup
rescan, other than relying on next loop to exit.
Reported-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3d3a2e610e ]
Currently the code assumes that there's an implied barrier by the
sequence of code preceding the wakeup, namely the mutex unlock.
As Nikolay pointed out:
I think this is wrong (not your code) but the original assumption that
the RELEASE semantics provided by mutex_unlock is sufficient.
According to memory-barriers.txt:
Section 'LOCK ACQUISITION FUNCTIONS' states:
(2) RELEASE operation implication:
Memory operations issued before the RELEASE will be completed before the
RELEASE operation has completed.
Memory operations issued after the RELEASE *may* be completed before the
RELEASE operation has completed.
(I've bolded the may portion)
The example given there:
As an example, consider the following:
*A = a;
*B = b;
ACQUIRE
*C = c;
*D = d;
RELEASE
*E = e;
*F = f;
The following sequence of events is acceptable:
ACQUIRE, {*F,*A}, *E, {*C,*D}, *B, RELEASE
So if we assume that *C is modifying the flag which the waitqueue is checking,
and *E is the actual wakeup, then those accesses can be re-ordered...
IMHO this code should be considered broken...
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c08db7d8d2 ]
In btrfs_evict_inode(), if btrfs_truncate_inode_items() fails, the inode
item will still be in the tree but we still return the ino to the ino
cache. That will blow up later when someone tries to allocate that ino,
so don't return it to the cache.
Fixes: 581bb05094 ("Btrfs: Cache free inode numbers in memory")
Reviewed-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 90b2da89a0 ]
When a buffer is queued or requeued in vb2_buffer_done, then don't
call the finish memop. In this case the buffer is only returned to vb2,
not to userspace.
Calling 'finish' here will cause an unbalance when the queue is
canceled, since the core will call the same memop again.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a3d71f256c ]
The current logic makes Smatch to false-detect a Spectre variant 1
vulnerability. The problem is that it initializes an u32 indirectly
from user space input.
After trying to write a fixup, after a while I realized that, in
practice, this shouldn't be a problem, as an u32 is initialized
from u8, but it took some time to discover it.
So, do some code cleanup to make it clearer for both humans
and machines about the valid range for "op".
Fix this warning:
drivers/media/cec/cec-pin-error-inj.c:170 cec_pin_error_inj_parse_line() warn: potential spectre issue 'pin->error_inj_args'
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7d0b130cbb ]
RX Buffer Descriptor contains a VALID bit which indicates if the BD
is valid and has some data. This field is set by HNS3 hardware to
intimate the driver of some valid data present in the BD. nd should
be reset by the driver when BD is being used again. In the existing
code this bit was not being (re-)initialized properly and hence was
causing problems.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 544a7bcd5c ]
When register a RoCE client with hnae3vf device, it needs to judge
the device whether support RoCE vf function. Otherwise, it will
lead to calltrace when RoCE is not support vf function and remove
roce device.
The calltrace as follows:
[ 93.156614] Unable to handle kernel NULL pointer dereference at virtual address 00000015
<SNIP>
[ 93.278784] Call trace:
[ 93.278788] hnae3_match_n_instantiate+0x24/0xd8 [hnae3]
[ 93.278790] hnae3_register_client+0xcc/0x150 [hnae3]
[ 93.278801] hns_roce_hw_v2_init+0x18/0x1000 [hns_roce_hw_v2]
[ 93.278805] do_one_initcall+0x58/0x160
[ 93.278807] do_init_module+0x64/0x1d8
[ 93.278809] load_module+0x135c/0x15c8
[ 93.278811] SyS_finit_module+0x100/0x118
[ 93.278816] __sys_trace_return+0x0/0x4
[ 93.278827] Code: aa0003f5 12001c56 aa1e03e0 d503201f (b9402660)
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Reported-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Reported-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6e91d48371 ]
the wl pointer can be null In case only wlcore_sdio is probed while
no WiLink module is successfully probed, as in the case of mounting a
wl12xx module while using a device tree file configured with wl18xx
related settings.
In this case the system was crashing in wl1271_suspend() as platform
device data is not set.
Make sure wl the pointer is valid before using it.
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b817047ae7 ]
Race condition is observed during rmmod of mwifiex_usb:
1. The rmmod thread will call mwifiex_usb_disconnect(), download
SHUTDOWN command and do wait_event_interruptible_timeout(),
waiting for response.
2. The main thread will handle the response and will do a
wake_up_interruptible(), unblocking rmmod thread.
3. On getting unblocked, rmmod thread will make rx_cmd.urb = NULL in
mwifiex_usb_free().
4. The main thread will try to resubmit rx_cmd.urb in
mwifiex_usb_submit_rx_urb(), which is NULL.
To fix, wait for main thread to complete before calling
mwifiex_usb_free().
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9c0ac70ad2 ]
In case, one BE is used by two FE1/FE2
FE1--->BE-->
|
FE2----]
when FE1/FE2 call dpcm_be_dai_hw_free() together
the BE users will be 2 (> 1), hence cannot be hw_free
the be state will leave at, ex. SND_SOC_DPCM_STATE_STOP
later FE1/FE2 call dpcm_be_dai_shutdown(),
will be skip due to wrong state.
leaving the BE not being hw_free and shutdown.
The BE dai will be hw_free later when calling
dpcm_be_dai_shutdown() if still in invalid state.
Signed-off-by: KaiChieh Chuang <kaichieh.chuang@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 984e9cf1b9 ]
When the arm-cci driver is enabled, but both CONFIG_ARM_CCI5xx_PMU and
CONFIG_ARM_CCI400_PMU are not, we get a warning about how parts of
the driver are never used:
drivers/perf/arm-cci.c:1454:29: error: 'cci_pmu_models' defined but not used [-Werror=unused-variable]
drivers/perf/arm-cci.c:693:16: error: 'cci_pmu_event_show' defined but not used [-Werror=unused-function]
drivers/perf/arm-cci.c:685:16: error: 'cci_pmu_format_show' defined but not used [-Werror=unused-function]
Marking all three functions as __maybe_unused avoids the warnings in
randconfig builds. I'm doing this lacking any ideas for a better fix.
Fixes: 3de6be7a3d ("drivers/bus: Split Arm CCI driver")
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9960521c44 ]
This patch fixes the following warning during boot:
do not call blocking ops when !TASK_RUNNING; state=1 set at
[<(ptrval)>] qca_setup+0x194/0x750 [hci_uart]
WARNING: CPU: 2 PID: 1878 at kernel/sched/core.c:6135
__might_sleep+0x7c/0x88
In qca_set_baudrate(), the current task state is set to
TASK_UNINTERRUPTIBLE before going to sleep for 300ms. It was then
restored to TASK_INTERRUPTIBLE. This patch sets the current task state
back to TASK_RUNNING instead.
Signed-off-by: Thierry Escande <thierry.escande@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d94c5a820d ]
Currently, a BA session is opened when the tx traffic exceeds
10 frames per second. As a result of inter-op problems with some
APs, add a condition to open BA session only when station is
already authorized.
Fixes: 482e48440a ("iwlwifi: mvm: change open and close criteria of a BA session")
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0f22e40053 ]
Make sure the rx_allocator worker is canceled before running the
rx_init routine. rx_init frees and re-allocates all rxb's pages. The
rx_allocator worker also allocates pages for the used rxb's. Running
rx_init and rx_allocator simultaniously causes a kernel panic. Fix
that by canceling the work in rx_init.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e73e81b6d0 ]
[Problem description and how we fix it]
We should balance dirty metadata pages at the end of
btrfs_finish_ordered_io, since a small, unmergeable random write can
potentially produce dirty metadata which is multiple times larger than
the data itself. For example, a small, unmergeable 4KiB write may
produce:
16KiB dirty leaf (and possibly 16KiB dirty node) in subvolume tree
16KiB dirty leaf (and possibly 16KiB dirty node) in checksum tree
16KiB dirty leaf (and possibly 16KiB dirty node) in extent tree
Although we do call balance dirty pages in write side, but in the
buffered write path, most metadata are dirtied only after we reach the
dirty background limit (which by far only counts dirty data pages) and
wakeup the flusher thread. If there are many small, unmergeable random
writes spread in a large btree, we'll find a burst of dirty pages
exceeds the dirty_bytes limit after we wakeup the flusher thread - which
is not what we expect. In our machine, it caused out-of-memory problem
since a page cannot be dropped if it is marked dirty.
Someone may worry about we may sleep in btrfs_btree_balance_dirty_nodelay,
but since we do btrfs_finish_ordered_io in a separate worker, it will not
stop the flusher consuming dirty pages. Also, we use different worker for
metadata writeback endio, sleep in btrfs_finish_ordered_io help us throttle
the size of dirty metadata pages.
[Reproduce steps]
To reproduce the problem, we need to do 4KiB write randomly spread in a
large btree. In our 2GiB RAM machine:
1) Create 4 subvolumes.
2) Run fio on each subvolume:
[global]
direct=0
rw=randwrite
ioengine=libaio
bs=4k
iodepth=16
numjobs=1
group_reporting
size=128G
runtime=1800
norandommap
time_based
randrepeat=0
3) Take snapshot on each subvolume and repeat fio on existing files.
4) Repeat step (3) until we get large btrees.
In our case, by observing btrfs_root_item->bytes_used, we have 2GiB of
metadata in each subvolume tree and 12GiB of metadata in extent tree.
5) Stop all fio, take snapshot again, and wait until all delayed work is
completed.
6) Start all fio. Few seconds later we hit OOM when the flusher starts
to work.
It can be reproduced even when using nocow write.
Signed-off-by: Ethan Lien <ethanlien@synology.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ add comment ]
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 480daa9cb6 ]
Driver switches vif sta_state into QTNF_STA_CONNECTING when cfg80211
core initiates connect procedure. Further this state is changed either
to QTNF_STA_CONNECTED or to QTNF_STA_DISCONNECTED by BSS_JOIN and
BSS_LEAVE events from firmware. However it is possible that no such
events will be sent by firmware, e.g. if EAPOL timed out.
In this case vif sta_mode will remain in QTNF_STA_CONNECTING state and
all subsequent connection attempts will fail with -EBUSY error code.
Fix this by perfroming STA state transition from QTNF_STA_CONNECTING
to QTNF_STA_DISCONNECTED in cfg80211 disconnect callback.
No need to rely upon firmware events in this case.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dd4b16b4f9 ]
We were picking up the wrong header should use asm/ioctls.h form the kernel
and not the header from the system (sys/ioctl.h). In the current code we
added the correct include and we added the kernel headers path to the CFLAGS.
Fixes: ce290a1960 ("selftests: add devpts selftests")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7357dcf2ef ]
When devpts_pts test is skipped because of unmet dependencies and/or
unsupported configuration, it exits with error which is treated as
a fail by the Kselftest framework. This leads to false negative
result even when the test could not be run.
In another case, it returns pass for a skipped test reporting a false
postive.
Change it to return kselftest skip code when a test gets skipped to
clearly report that the test could not be run.
Change it to use ksft_exit_skip() when test is skipped.
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5c30a038fb ]
When intel_pstate test is skipped because of unmet dependencies and/or
unsupported configuration, it returns 0 which is treated as a pass
by the Kselftest framework. This leads to false positive result even
when the test could not be run.
Change it to return kselftest skip code when a test gets skipped to
clearly report that the test could not be run.
Kselftest framework SKIP code is 4 and the framework prints appropriate
messages to indicate that the test is skipped.
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ab0e9c4b91 ]
When kvm test is skipped because of unmet dependencies and/or unsupported
configuration, it exits with error which is treated as a fail by the
Kselftest framework. This leads to false negative result even when the test
could not be run.
Change it to return kselftest skip code when a test gets skipped to clearly
report that the test could not be run.
Change it to use ksft_exit_skip() when the test is skipped. In addition,
refine test_assert() message to include strerror() string and add explicit
check for EACCES to cleary identify when test doesn't run when access is
denied to resources required e.g: open /dev/kvm failed, rc: -1 errno: 13
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b27f0259e8 ]
When memfd test is skipped because of unmet dependencies and/or unsupported
configuration, it returns non-zero value which is treated as a fail by the
Kselftest framework. This leads to false negative result even when the test
could not be run.
Change it to return kselftest skip code when a test gets skipped to clearly
report that the test could not be run.
Added an explicit check for root user at the start of memfd hugetlbfs test
and return skip code if a non-root user attempts to run it.
In addition, return skip code when not enough huge pages are available to
run the test.
Kselftest framework SKIP code is 4 and the framework prints appropriate
messages to indicate that the test is skipped.
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e9d33f149f ]
A few changes improve the overall usability of the test:
* fix a hard-coded maximum frequency (3300),
* don't adjust the CPU frequency if only evaluating results,
* fix a comparison for multiple frequencies.
A symptom of that last issue looked like this:
./run.sh: line 107: [: too many arguments
./run.sh: line 110: 3099
3099
3100-3100: syntax error in expression (error token is \"3099
3100-3100\")
Because a check will count how many differente frequencies
there are among the CPUs of the system, and after they are
tallied another read is performed, which might produce
different results.
Signed-off-by: Daniel Díaz <daniel.diaz@linaro.org>
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a12bffebc0 ]
In bfq_requests_merged(), there is a deadlock because the lock on
bfqq->bfqd->lock is held by the calling function, but the code of
this function tries to grab the lock again.
This deadlock is currently hidden by another bug (fixed by next commit
for this source file), which causes the body of bfq_requests_merged()
to be never executed.
This commit removes the deadlock by removing the lock/unlock pair.
Signed-off-by: Filippo Muzzini <filippo.muzzini@outlook.it>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e5e5732d81 ]
After revoking atomic write, related LBA can be reused by others, so we
need to wait page writeback before reusing the LBA, in order to avoid
interference between old atomic written in-flight IO and new IO.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1174abfd83 ]
As description in commit "f2fs: don't drop any page on f2fs_cp_error()
case":
"We still provide readdir() after shtudown, so we should keep pages to
avoid additional IOs."
In order to provider lastest directory structure, let's keep dentry
pages in cache after fs shutdown.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4071e67cff ]
The following patch disables loading of f2fs module on architectures
which have PAGE_SIZE > 4096 , since it is impossible to mount f2fs on
such architectures , log messages are:
mount: /mnt: wrong fs type, bad option, bad superblock on
/dev/vdiskb1, missing codepage or helper program, or other error.
/dev/vdiskb1: F2FS filesystem,
UUID=1d8b9ca4-2389-4910-af3b-10998969f09c, volume name ""
May 15 18:03:13 ttip kernel: F2FS-fs (vdiskb1): Invalid
page_cache_size (8192), supports only 4KB
May 15 18:03:13 ttip kernel: F2FS-fs (vdiskb1): Can't find valid F2FS
filesystem in 1th superblock
May 15 18:03:13 ttip kernel: F2FS-fs (vdiskb1): Invalid
page_cache_size (8192), supports only 4KB
May 15 18:03:13 ttip kernel: F2FS-fs (vdiskb1): Can't find valid F2FS
filesystem in 2th superblock
May 15 18:03:13 ttip kernel: F2FS-fs (vdiskb1): Invalid
page_cache_size (8192), supports only 4KB
which was introduced by git commit 5c9b469295
tested on git kernel 4.17.0-rc6-00309-gec30dcf7f425
with patch applied:
modprobe: ERROR: could not insert 'f2fs': Invalid argument
May 28 01:40:28 v215 kernel: F2FS not supported on PAGE_SIZE(8192) != 4096
Signed-off-by: Anatoly Pugachev <matorola@gmail.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ae55e59da0 ]
If the server recalls the layout that was just handed out, we risk hitting
a race as described in RFC5661 Section 2.10.6.3 unless we ensure that we
release the sequence slot after processing the LAYOUTGET operation that
was sent as part of the OPEN compound.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e37d07983a ]
When cleaning up buffer entries as we wrap up, their state should be
"completed". If any of the entries is in "submitted" state, it means
that something bad has happened. Trigger a warning immediately instead of
waiting for the state flag to eventually be updated, thus hiding the
issue.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f142ac0b5d ]
Currently in case of error caused by bio_pc_add_page in
pblk_bio_add_pages two issues occur when calling from
pblk_rb_read_to_bio(). First one is in pblk_bio_free_pages, since we
are trying to free pages not allocated from our mempool. Second one
is the warn from dma_pool_free, that we are trying to free NULL
pointer dma.
This commit fix both issues.
Signed-off-by: Igor Konopko <igor.j.konopko@intel.com>
Signed-off-by: Marcin Dziegielewski <marcin.dziegielewski@intel.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f5be79673f ]
When hclge_ae_stop is called during resetting, it will cancel the
service_task by calling cancel_work_sync, which may cause the
service_task to exit without clearing HCLGE_STATE_SERVICE_SCHED
bit. If this happens, the service_task will never run again.
This patch fixes this problem by clearing it after calling
cancel_work_sync in hclge_ae_stop.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9617f66867 ]
When resetting, phy_state_machine may be accessing the phy through
firmware if the phy is not stopped or disconnected, which will
cause firemware timeout problem because the firmware is busy
processing the reset request.
This patch fixes it by disabling the phy when resetting.
Fixes: b940aeae0ed6 ("net: hns3: never send command queue message to IMP when reset")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 45ba63a29f ]
When the main processor goes idle, by default its clock is stopped.
However, this also stops the clock of the co-processor.
Here, if the C1CLK clock is enabled, we disable this functionality.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4d3f36c5e9 ]
The si544 driver had a rounding problem that using the result of clk_round_rate
may set the clock to yet another rate, for example:
clk_round_rate(195000000) = 194999999
clk_round_rate(194999999) = 194999998
Clients would expect that after clk_set_rate(clk, freq2=clk_round_rate(clk, freq)) the
chip will be running at exactly freq2.
The problem was in the calculation of the feedback divider, it was always rounded
down instead of to the nearest possible VCO value.
After this change, the following holds true for any supported frequency:
actual_freq = clk_round_rate(clk, freq);
clk_set_rate(clk, actual_freq);
clk_round_rate(clk, actual_freq) == actual_freq && clk_get_rate(clk) == actual_freq
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Fixes: 953cc3e811 ("clk: Add driver for the si544 clock generator chip")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 926bc2f100 ]
The stores to update the SLB shadow area must be made as they appear
in the C code, so that the hypervisor does not see an entry with
mismatched vsid and esid. Use WRITE_ONCE for this.
GCC has been observed to elide the first store to esid in the update,
which means that if the hypervisor interrupts the guest after storing
to vsid, it could see an entry with old esid and new vsid, which may
possibly result in memory corruption.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 447808bf50 ]
time_init() will set up tb_ticks_per_usec based on reality.
time_init() is called *after* udbg_init_opal_common() during boot.
from arch/powerpc/kernel/time.c:
unsigned long tb_ticks_per_usec = 100; /* sane default */
Currently, all powernv systems have a timebase frequency of 512mhz
(512000000/1000000 == 0x200) - although there's nothing written
down anywhere that I can find saying that we couldn't make that
different based on the requirements in the ISA.
So, we've been (accidentally) thwacking the (currently) correct
(for powernv at least) value for tb_ticks_per_usec earlier than
we otherwise would have.
The "sane default" seems to be adequate for our purposes between
udbg_init_opal_common() and time_init() being called, and if it isn't,
then we should probably be setting it somewhere that isn't hvc_opal.c!
Signed-off-by: Stewart Smith <stewart@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 46d4be41b9 ]
Correct two cases where eeh_pcid_get() is used to reference the driver's
module but the reference is dropped before the driver pointer is used.
In eeh_rmv_device() also refactor a little so that only two calls to
eeh_pcid_put() are needed, rather than three and the reference isn't
taken at all if it wasn't needed.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a6b3964ad7 ]
A no-op form of ori (or immediate of 0 into r31 and the result stored
in r31) has been re-tasked as a speculation barrier. The instruction
only acts as a barrier on newer machines with appropriate firmware
support. On older CPUs it remains a harmless no-op.
Implement barrier_nospec using this instruction.
mpe: The semantics of the instruction are believed to be that it
prevents execution of subsequent instructions until preceding branches
have been fully resolved and are no longer executing speculatively.
There is no further documentation available at this time.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1128bb7813 ]
commit 87a156fb18 ("Align hot loops of some string functions")
degraded the performance of string functions by adding useless
nops
A simple benchmark on an 8xx calling 100000x a memchr() that
matches the first byte runs in 41668 TB ticks before this patch
and in 35986 TB ticks after this patch. So this gives an
improvement of approx 10%
Another benchmark doing the same with a memchr() matching the 128th
byte runs in 1011365 TB ticks before this patch and 1005682 TB ticks
after this patch, so regardless on the number of loops, removing
those useless nops improves the test by 5683 TB ticks.
Fixes: 87a156fb18 ("Align hot loops of some string functions")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cb2595c139 ]
ucma_process_join() will free the new allocated "mc" struct,
if there is any error after that, especially the copy_to_user().
But in parallel, ucma_leave_multicast() could find this "mc"
through idr_find() before ucma_process_join() frees it, since it
is already published.
So "mc" could be used in ucma_leave_multicast() after it is been
allocated and freed in ucma_process_join(), since we don't refcnt
it.
Fix this by separating "publish" from ID allocation, so that we
can get an ID first and publish it later after copy_to_user().
Fixes: c8f6a362bf ("RDMA/cma: Add multicast communication support")
Reported-by: Noam Rathaus <noamr@beyondsecurity.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fff200caf6 ]
There have been multiple reports of crashes that look like
kernel: RIP: 0010:[<ffffffff8110303f>] timecounter_read+0xf/0x50
[...]
kernel: Call Trace:
kernel: [<ffffffffa0806b0f>] e1000e_phc_gettime+0x2f/0x60 [e1000e]
kernel: [<ffffffffa0806c5d>] e1000e_systim_overflow_work+0x1d/0x80 [e1000e]
kernel: [<ffffffff810992c5>] process_one_work+0x155/0x440
kernel: [<ffffffff81099e16>] worker_thread+0x116/0x4b0
kernel: [<ffffffff8109f422>] kthread+0xd2/0xf0
kernel: [<ffffffff8163184f>] ret_from_fork+0x3f/0x70
These can be traced back to the fact that e1000e_systim_reset() skips the
timecounter_init() call if e1000e_get_base_timinca() returns -EINVAL, which
leads to a null deref in timecounter_read().
Commit 83129b37ef ("e1000e: fix systim issues", v4.2-rc1) reworked
e1000e_get_base_timinca() in such a way that it can return -EINVAL for
e1000_pch_spt if the SYSCFI bit is not set in TSYNCRXCTL.
Some experimentation has shown that on I219 (e1000_pch_spt, "MAC: 12")
adapters, the E1000_TSYNCRXCTL_SYSCFI flag is unstable; TSYNCRXCTL reads
sometimes don't have the SYSCFI bit set. Retrying the read shortly after
finds the bit to be set. This was observed at boot (probe) but also link up
and link down.
Moreover, the phc (PTP Hardware Clock) seems to operate normally even after
reads where SYSCFI=0. Therefore, remove this register read and
unconditionally set the clock parameters.
Reported-by: Achim Mildenberger <admin@fph.physik.uni-karlsruhe.de>
Message-Id: <20180425065243.g5mqewg5irkwgwgv@f2>
Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=1075876
Fixes: 83129b37ef ("e1000e: fix systim issues")
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 73fb0949cf ]
KASAN found an UAF in ceph_statfs. This was a one-off bug but looking at
the code it looks like the monmap access needs to be protected as it can
be modified while we're accessing it. Fix this by protecting the access
with the monc->mutex.
BUG: KASAN: use-after-free in ceph_statfs+0x21d/0x2c0
Read of size 8 at addr ffff88006844f2e0 by task trinity-c5/304
CPU: 0 PID: 304 Comm: trinity-c5 Not tainted 4.17.0-rc6+ #172
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.0.0-prebuilt.qemu-project.org 04/01/2014
Call Trace:
dump_stack+0xa5/0x11b
? show_regs_print_info+0x5/0x5
? kmsg_dump_rewind+0x118/0x118
? ceph_statfs+0x21d/0x2c0
print_address_description+0x73/0x2b0
? ceph_statfs+0x21d/0x2c0
kasan_report+0x243/0x360
ceph_statfs+0x21d/0x2c0
? ceph_umount_begin+0x80/0x80
? kmem_cache_alloc+0xdf/0x1a0
statfs_by_dentry+0x79/0xb0
vfs_statfs+0x28/0x110
user_statfs+0x8c/0xe0
? vfs_statfs+0x110/0x110
? __fdget_raw+0x10/0x10
__se_sys_statfs+0x5d/0xa0
? user_statfs+0xe0/0xe0
? mutex_unlock+0x1d/0x40
? __x64_sys_statfs+0x20/0x30
do_syscall_64+0xee/0x290
? syscall_return_slowpath+0x1c0/0x1c0
? page_fault+0x1e/0x30
? syscall_return_slowpath+0x13c/0x1c0
? prepare_exit_to_usermode+0xdb/0x140
? syscall_trace_enter+0x330/0x330
? __put_user_4+0x1c/0x30
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Allocated by task 130:
__kmalloc+0x124/0x210
ceph_monmap_decode+0x1c1/0x400
dispatch+0x113/0xd20
ceph_con_workfn+0xa7e/0x44e0
process_one_work+0x5f0/0xa30
worker_thread+0x184/0xa70
kthread+0x1a0/0x1c0
ret_from_fork+0x35/0x40
Freed by task 130:
kfree+0xb8/0x210
dispatch+0x15a/0xd20
ceph_con_workfn+0xa7e/0x44e0
process_one_work+0x5f0/0xa30
worker_thread+0x184/0xa70
kthread+0x1a0/0x1c0
ret_from_fork+0x35/0x40
Signed-off-by: Luis Henriques <lhenriques@suse.com>
Reviewed-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2b787b66bc ]
The TW9910 PDN gpio (power down) is listed as active high in the chip
manual. It turns out it is actually active low as when set to physical
level 0 it actually turns the video decoder power off.
Without this patch applied:
tw9910 0-0045: Product ID error 1f:2
With this patch applied:
tw9910 0-0045: tw9910 Product ID b:0
Fixes: commit "186c446f4b840bd77b79d3dc951ca436cb8abe79"
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 44ee54aabf ]
The DA9063 watchdog has only one register field to store the timeout value
and to enable the watchdog. The watchdog gets enabled if the value is
not zero. There is no issue if the watchdog is already running but it
leads into problems if the watchdog is disabled.
If the watchdog is disabled and only the timeout value should be prepared
the watchdog gets enabled too. Add a check to get the current watchdog
state and update the watchdog timeout value on hw-side only if the
watchdog is already active.
Fixes: 5e9c16e376 ("watchdog: Add DA9063 PMIC watchdog driver.")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bd975e6914 ]
When listing sets with timeout support, there's a probability that
just timing out entries with "0" timeout value is listed/saved.
However when restoring the saved list, the zero timeout value means
permanent elelements.
The new behaviour is that timing out entries are listed with "timeout 1"
instead of zero.
Fixes netfilter bugzilla #1258.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cbdebe481a ]
Userspace `ipset` command forbids family option for hash:mac type:
ipset create test hash:mac family inet4
ipset v6.30: Unknown argument: `family'
However, this check is not done in kernel itself. When someone use
external netlink applications (pyroute2 python library for example), one
can create hash:mac with invalid family and inconsistant results from
userspace (`ipset` command cannot read set content anymore).
This patch enforce the logic in kernel, and forbids insertion of
hash:mac with a family set.
Since IP_SET_PROTO_UNDEF is defined only for hash:mac, this patch has no
impact on other hash:* sets
Signed-off-by: Florent Fourcot <florent.fourcot@wifirst.fr>
Signed-off-by: Victorien Molle <victorien.molle@wifirst.fr>
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1819e40908 ]
When the VF frequently switches the CMDQ interrupt, if the CMDQ_SRC is not
cleared, the VF will not receive the new PF response after the interrupt
is re-enabled, the corresponding log is as follows:
[ 317.482222] hns3 0000:00:03.0: VF could not get mbx resp(=0) from PF
in 500 tries
[ 317.483137] hns3 0000:00:03.0: VF request to get tqp info from PF
failed -5
This patch fixes this problem by clearing CMDQ_SRC before enabling
interrupt and syncing pending IRQ handlers after disabling interrupt.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fb1967a69f ]
When retransmitting the final ACK or ABORT packet for a call, the cid field
in the packet header is set to the connection's cid, but this is incorrect
as it also needs to include the channel number on that connection that the
call was made on.
Fix this by OR'ing in the channel number.
Note that this fixes the bug that:
commit 1a025028d4
rxrpc: Fix handling of call quietly cancelled out on server
works around. I'm not intending to revert that as it will help protect
against problems that might occur on the server.
Fixes: 3136ef49a1 ("rxrpc: Delay terminal ACK transmission on a client call")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit abfdff44bc ]
When using RTC_ALM_SET or RTC_WKALM_SET with rtc_wkalrm.enabled not set,
rtc_timer_enqueue() is not called and rtc_set_alarm() may succeed but the
subsequent RTC_AIE_ON ioctl will fail. RTC_ALM_READ would also fail in that
case.
Ensure rtc_set_alarm() fails when alarms are not supported to avoid letting
programs think the alarms are working for a particular RTC when they are
not.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e81bf9793b ]
The LKP robot found a 27% will-it-scale/page_fault3 performance
regression regarding commit e27be240df53("mm: memcg: make sure
memory.events is uptodate when waking pollers").
What the test does is:
1 mkstemp() a 128M file on a tmpfs;
2 start $nr_cpu processes, each to loop the following:
2.1 mmap() this file in shared write mode;
2.2 write 0 to this file in a PAGE_SIZE step till the end of the file;
2.3 unmap() this file and repeat this process.
3 After 5 minutes, check how many loops they managed to complete, the
higher the better.
The commit itself looks innocent enough as it merely changed some event
counting mechanism and this test didn't trigger those events at all.
Perf shows increased cycles spent on accessing root_mem_cgroup->stat_cpu
in count_memcg_event_mm()(called by handle_mm_fault()) and in
__mod_memcg_state() called by page_add_file_rmap(). So it's likely due
to the changed layout of 'struct mem_cgroup' that either make stat_cpu
falling into a constantly modifying cacheline or some hot fields stop
being in the same cacheline.
I verified this by moving memory_events[] back to where it was:
: --- a/include/linux/memcontrol.h
: +++ b/include/linux/memcontrol.h
: @@ -205,7 +205,6 @@ struct mem_cgroup {
: int oom_kill_disable;
:
: /* memory.events */
: - atomic_long_t memory_events[MEMCG_NR_MEMORY_EVENTS];
: struct cgroup_file events_file;
:
: /* protect arrays of thresholds */
: @@ -238,6 +237,7 @@ struct mem_cgroup {
: struct mem_cgroup_stat_cpu __percpu *stat_cpu;
: atomic_long_t stat[MEMCG_NR_STAT];
: atomic_long_t events[NR_VM_EVENT_ITEMS];
: + atomic_long_t memory_events[MEMCG_NR_MEMORY_EVENTS];
:
: unsigned long socket_pressure;
And performance restored.
Later investigation found that as long as the following 3 fields
moving_account, move_lock_task and stat_cpu are in the same cacheline,
performance will be good. To avoid future performance surprise by other
commits changing the layout of 'struct mem_cgroup', this patch makes
sure the 3 fields stay in the same cacheline.
One concern of this approach is, moving_account and move_lock_task could
be modified when a process changes memory cgroup while stat_cpu is a
always read field, it might hurt to place them in the same cacheline. I
assume it is rare for a process to change memory cgroup so this should
be OK.
Link: https://lkml.kernel.org/r/20180528114019.GF9904@yexl-desktop
Link: http://lkml.kernel.org/r/20180601071115.GA27302@intel.com
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Reported-by: kernel test robot <xiaolong.ye@intel.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 401c636a0e ]
When we get a hung task it can often be valuable to see _all_ the hung
tasks on the system before calling panic().
Quoting from https://syzkaller.appspot.com/text?tag=CrashReport&id=5316056503549952
----------------------------------------
INFO: task syz-executor0:6540 blocked for more than 120 seconds.
Not tainted 4.16.0+ #13
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
syz-executor0 D23560 6540 4521 0x80000004
Call Trace:
context_switch kernel/sched/core.c:2848 [inline]
__schedule+0x8fb/0x1ef0 kernel/sched/core.c:3490
schedule+0xf5/0x430 kernel/sched/core.c:3549
schedule_preempt_disabled+0x10/0x20 kernel/sched/core.c:3607
__mutex_lock_common kernel/locking/mutex.c:833 [inline]
__mutex_lock+0xb7f/0x1810 kernel/locking/mutex.c:893
mutex_lock_nested+0x16/0x20 kernel/locking/mutex.c:908
lo_ioctl+0x8b/0x1b70 drivers/block/loop.c:1355
__blkdev_driver_ioctl block/ioctl.c:303 [inline]
blkdev_ioctl+0x1759/0x1e00 block/ioctl.c:601
ioctl_by_bdev+0xa5/0x110 fs/block_dev.c:2060
isofs_get_last_session fs/isofs/inode.c:567 [inline]
isofs_fill_super+0x2ba9/0x3bc0 fs/isofs/inode.c:660
mount_bdev+0x2b7/0x370 fs/super.c:1119
isofs_mount+0x34/0x40 fs/isofs/inode.c:1560
mount_fs+0x66/0x2d0 fs/super.c:1222
vfs_kern_mount.part.26+0xc6/0x4a0 fs/namespace.c:1037
vfs_kern_mount fs/namespace.c:2514 [inline]
do_new_mount fs/namespace.c:2517 [inline]
do_mount+0xea4/0x2b90 fs/namespace.c:2847
ksys_mount+0xab/0x120 fs/namespace.c:3063
SYSC_mount fs/namespace.c:3077 [inline]
SyS_mount+0x39/0x50 fs/namespace.c:3074
do_syscall_64+0x281/0x940 arch/x86/entry/common.c:287
entry_SYSCALL_64_after_hwframe+0x42/0xb7
(...snipped...)
Showing all locks held in the system:
(...snipped...)
2 locks held by syz-executor0/6540:
#0: 00000000566d4c39 (&type->s_umount_key#49/1){+.+.}, at: alloc_super fs/super.c:211 [inline]
#0: 00000000566d4c39 (&type->s_umount_key#49/1){+.+.}, at: sget_userns+0x3b2/0xe60 fs/super.c:502 /* down_write_nested(&s->s_umount, SINGLE_DEPTH_NESTING); */
#1: 0000000043ca8836 (&lo->lo_ctl_mutex/1){+.+.}, at: lo_ioctl+0x8b/0x1b70 drivers/block/loop.c:1355 /* mutex_lock_nested(&lo->lo_ctl_mutex, 1); */
(...snipped...)
3 locks held by syz-executor7/6541:
#0: 0000000043ca8836 (&lo->lo_ctl_mutex/1){+.+.}, at: lo_ioctl+0x8b/0x1b70 drivers/block/loop.c:1355 /* mutex_lock_nested(&lo->lo_ctl_mutex, 1); */
#1: 000000007bf3d3f9 (&bdev->bd_mutex){+.+.}, at: blkdev_reread_part+0x1e/0x40 block/ioctl.c:192
#2: 00000000566d4c39 (&type->s_umount_key#50){.+.+}, at: __get_super.part.10+0x1d3/0x280 fs/super.c:663 /* down_read(&sb->s_umount); */
----------------------------------------
When reporting an AB-BA deadlock like shown above, it would be nice if
trace of PID=6541 is printed as well as trace of PID=6540 before calling
panic().
Showing hung tasks up to /proc/sys/kernel/hung_task_warnings could delay
calling panic() but normally there should not be so many hung tasks.
Link: http://lkml.kernel.org/r/201804050705.BHE57833.HVFOFtSOMQJFOL@I-love.SAKURA.ne.jp
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Vegard Nossum <vegard.nossum@oracle.com>
Cc: Mandeep Singh Baines <msb@chromium.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 48d8476b41 ]
MAP_DMA ioctls might be called from various threads within a process,
for example when using QEMU, the vCPU threads are often generating
these calls and we therefore take a reference to that vCPU task.
However, QEMU also supports vCPU hotplug on some machines and the task
that called MAP_DMA may have exited by the time UNMAP_DMA is called,
resulting in the mm_struct pointer being NULL and thus a failure to
match against the existing mapping.
To resolve this, we instead take a reference to the thread
group_leader, which has the same mm_struct and resource limits, but
is less likely exit, at least in the QEMU case. A difficulty here is
guaranteeing that the capabilities of the group_leader match that of
the calling thread, which we resolve by tracking CAP_IPC_LOCK at the
time of calling rather than at an indeterminate time in the future.
Potentially this also results in better efficiency as this is now
recorded once per MAP_DMA ioctl.
Reported-by: Xu Yandong <xuyandong2@huawei.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 002fe996f6 ]
When we create an mdev device, we check for duplicates against the
parent device and return -EEXIST if found, but the mdev device
namespace is global since we'll link all devices from the bus. We do
catch this later in sysfs_do_create_link_sd() to return -EEXIST, but
with it comes a kernel warning and stack trace for trying to create
duplicate sysfs links, which makes it an undesirable response.
Therefore we should really be looking for duplicates across all mdev
parent devices, or as implemented here, against our mdev device list.
Using mdev_list to prevent duplicates means that we can remove
mdev_parent.lock, but in order not to serialize mdev device creation
and removal globally, we add mdev_device.active which allows UUIDs to
be reserved such that we can drop the mdev_list_lock before the mdev
device is fully in place.
Two behavioral notes; first, mdev_parent.lock had the side-effect of
serializing mdev create and remove ops per parent device. This was
an implementation detail, not an intentional guarantee provided to
the mdev vendor drivers. Vendor drivers can trivially provide this
serialization internally if necessary. Second, review comments note
the new -EAGAIN behavior when the device, and in particular the remove
attribute, becomes visible in sysfs. If a remove is triggered prior
to completion of mdev_device_create() the user will see a -EAGAIN
error. While the errno is different, receiving an error during this
period is not, the previous implementation returned -ENODEV for the
same condition. Furthermore, the consistency to the user is improved
in the case where mdev_device_remove_ops() returns error. Previously
concurrent calls to mdev_device_remove() could see the device
disappear with -ENODEV and return in the case of error. Now a user
would see -EAGAIN while the device is in this transitory state.
Reviewed-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3171822fdc ]
When running a fuzz tester against a KASAN-enabled kernel, the following
splat periodically occurs.
The problem occurs when the test sends a GETDEVICEINFO request with a
malformed xdr array (size but no data) for gdia_notify_types and the
array size is > 0x3fffffff, which results in an overflow in the value of
nbytes which is passed to read_buf().
If the array size is 0x40000000, 0x80000000, or 0xc0000000, then after
the overflow occurs, the value of nbytes 0, and when that happens the
pointer returned by read_buf() points to the end of the xdr data (i.e.
argp->end) when really it should be returning NULL.
Fix this by returning NFS4ERR_BAD_XDR if the array size is > 1000 (this
value is arbitrary, but it's the same threshold used by
nfsd4_decode_bitmap()... in could really be any value >= 1 since it's
expected to get at most a single bitmap in gdia_notify_types).
[ 119.256854] ==================================================================
[ 119.257611] BUG: KASAN: use-after-free in nfsd4_decode_getdeviceinfo+0x5a4/0x5b0 [nfsd]
[ 119.258422] Read of size 4 at addr ffff880113ada000 by task nfsd/538
[ 119.259146] CPU: 0 PID: 538 Comm: nfsd Not tainted 4.17.0+ #1
[ 119.259662] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.9.3-1.fc25 04/01/2014
[ 119.261202] Call Trace:
[ 119.262265] dump_stack+0x71/0xab
[ 119.263371] print_address_description+0x6a/0x270
[ 119.264609] kasan_report+0x258/0x380
[ 119.265854] ? nfsd4_decode_getdeviceinfo+0x5a4/0x5b0 [nfsd]
[ 119.267291] nfsd4_decode_getdeviceinfo+0x5a4/0x5b0 [nfsd]
[ 119.268549] ? nfs4svc_decode_compoundargs+0xa5b/0x13c0 [nfsd]
[ 119.269873] ? nfsd4_decode_sequence+0x490/0x490 [nfsd]
[ 119.271095] nfs4svc_decode_compoundargs+0xa5b/0x13c0 [nfsd]
[ 119.272393] ? nfsd4_release_compoundargs+0x1b0/0x1b0 [nfsd]
[ 119.273658] nfsd_dispatch+0x183/0x850 [nfsd]
[ 119.274918] svc_process+0x161c/0x31a0 [sunrpc]
[ 119.276172] ? svc_printk+0x190/0x190 [sunrpc]
[ 119.277386] ? svc_xprt_release+0x451/0x680 [sunrpc]
[ 119.278622] nfsd+0x2b9/0x430 [nfsd]
[ 119.279771] ? nfsd_destroy+0x1c0/0x1c0 [nfsd]
[ 119.281157] kthread+0x2db/0x390
[ 119.282347] ? kthread_create_worker_on_cpu+0xc0/0xc0
[ 119.283756] ret_from_fork+0x35/0x40
[ 119.286041] Allocated by task 436:
[ 119.287525] kasan_kmalloc+0xa0/0xd0
[ 119.288685] kmem_cache_alloc+0xe9/0x1f0
[ 119.289900] get_empty_filp+0x7b/0x410
[ 119.291037] path_openat+0xca/0x4220
[ 119.292242] do_filp_open+0x182/0x280
[ 119.293411] do_sys_open+0x216/0x360
[ 119.294555] do_syscall_64+0xa0/0x2f0
[ 119.295721] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 119.298068] Freed by task 436:
[ 119.299271] __kasan_slab_free+0x130/0x180
[ 119.300557] kmem_cache_free+0x78/0x210
[ 119.301823] rcu_process_callbacks+0x35b/0xbd0
[ 119.303162] __do_softirq+0x192/0x5ea
[ 119.305443] The buggy address belongs to the object at ffff880113ada000
which belongs to the cache filp of size 256
[ 119.308556] The buggy address is located 0 bytes inside of
256-byte region [ffff880113ada000, ffff880113ada100)
[ 119.311376] The buggy address belongs to the page:
[ 119.312728] page:ffffea00044eb680 count:1 mapcount:0 mapping:0000000000000000 index:0xffff880113ada780
[ 119.314428] flags: 0x17ffe000000100(slab)
[ 119.315740] raw: 0017ffe000000100 0000000000000000 ffff880113ada780 00000001000c0001
[ 119.317379] raw: ffffea0004553c60 ffffea00045c11e0 ffff88011b167e00 0000000000000000
[ 119.319050] page dumped because: kasan: bad access detected
[ 119.321652] Memory state around the buggy address:
[ 119.322993] ffff880113ad9f00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 119.324515] ffff880113ad9f80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 119.326087] >ffff880113ada000: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 119.327547] ^
[ 119.328730] ffff880113ada080: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 119.330218] ffff880113ada100: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb
[ 119.331740] ==================================================================
Signed-off-by: Scott Mayhew <smayhew@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 692ad280bf ]
I noticed a memory corruption crash in nfsd in
4.17-rc1. This patch corrects the issue.
Fix to return error if the delegation couldn't be hashed or there was
a recall in progress. Use the existing error path instead of
destroy_delegation() for readability.
Signed-off-by: Andrew Elble <aweits@rit.edu>
Fixes: 353601e7d3 ("nfsd: create a separate lease for each delegation")
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f9312a5410 ]
If the server returns NFS4ERR_SEQ_FALSE_RETRY or NFS4ERR_RETRY_UNCACHED_REP,
then it thinks we're trying to replay an existing request. If so, then
let's just bump the sequence ID and retry the operation.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 646bb57ce8 ]
When we were enabling macvlan interfaces we weren't correctly configuring
things until ixgbe_setup_tc was called a second time either by tweaking the
number of queues or increasing the macvlan count past 15.
The issue came down to the fact that num_rx_pools is not populated until
after the queues and interrupts are reinitialized.
Instead of trying to set it sooner we can just move the call to setup at
least 1 traffic class to the SR-IOV/VMDq setup function so that we just set
it for this one case. We already had a spot that was configuring the queues
for TC 0 in the code here anyway so it makes sense to also set the number
of TCs here as well.
Fixes: 49cfbeb7a9 ("ixgbe: Fix handling of macvlan Tx offload")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 93b7f7ad20 ]
Currently, when IO to DS fails, client returns the layout and
retries against the MDS. However, then on umounting (inode eviction)
it returns the layout again.
This is because pnfs_return_layout() was changed in
commit d78471d32b ("pnfs/blocklayout: set PNFS_LAYOUTRETURN_ON_ERROR")
to always set NFS_LAYOUT_RETURN_REQUESTED so even if we returned
the layout, it will be returned again. Instead, let's also check
if we have already marked the layout invalid.
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7bf7bb37f1 ]
When finding the parent netvsc device, the search needs to be across
all netvsc device instances (independent of network namespace).
Find parent device of VF using upper_dev_get routine which
searches only adjacent list.
Fixes: e8ff40d4bf ("hv_netvsc: improve VF device matching")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
netns aware byref
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 57f230ab04 ]
The max number of slots used in xennet_get_responses() is set to
MAX_SKB_FRAGS + (rx->status <= RX_COPY_THRESHOLD).
In old kernel-xen MAX_SKB_FRAGS was 18, while nowadays it is 17. This
difference is resulting in frequent messages "too many slots" and a
reduced network throughput for some workloads (factor 10 below that of
a kernel-xen based guest).
Replacing MAX_SKB_FRAGS by XEN_NETIF_NR_SLOTS_MIN for calculation of
the max number of slots to use solves that problem (tests showed no
more messages "too many slots" and throughput was as high as with the
kernel-xen based guest system).
Replace MAX_SKB_FRAGS-2 by XEN_NETIF_NR_SLOTS_MIN-1 in
netfront_tx_slot_available() for making it clearer what is really being
tested without actually modifying the tested value.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 655c79bb40 ]
As a theoretical problem, dup_mmap() of an mm_struct with 60000+ vmas
can loop while potentially allocating memory, with mm->mmap_sem held for
write by current thread. This is bad if current thread was selected as
an OOM victim, for current thread will continue allocations using memory
reserves while OOM reaper is unable to reclaim memory.
As an actually observable problem, it is not difficult to make OOM
reaper unable to reclaim memory if the OOM victim is blocked at
i_mmap_lock_write() in this loop. Unfortunately, since nobody can
explain whether it is safe to use killable wait there, let's check for
SIGKILL before trying to allocate memory. Even without an OOM event,
there is no point with continuing the loop from the beginning if current
thread is killed.
I tested with debug printk(). This patch should be safe because we
already fail if security_vm_enough_memory_mm() or
kmem_cache_alloc(GFP_KERNEL) fails and exit_mmap() handles it.
***** Aborting dup_mmap() due to SIGKILL *****
***** Aborting dup_mmap() due to SIGKILL *****
***** Aborting dup_mmap() due to SIGKILL *****
***** Aborting dup_mmap() due to SIGKILL *****
***** Aborting exit_mmap() due to NULL mmap *****
[akpm@linux-foundation.org: add comment]
Link: http://lkml.kernel.org/r/201804071938.CDE04681.SOFVQJFtMHOOLF@I-love.SAKURA.ne.jp
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Rik van Riel <riel@redhat.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c9484b986e ]
Patch series "kcov: fix unexpected faults".
These patches fix a few issues where KCOV code could trigger recursive
faults, discovered while debugging a patch enabling KCOV for arch/arm:
* On CONFIG_PREEMPT kernels, there's a small race window where
__sanitizer_cov_trace_pc() can see a bogus kcov_area.
* Lazy faulting of the vmalloc area can cause mutual recursion between
fault handling code and __sanitizer_cov_trace_pc().
* During the context switch, switching the mm can cause the kcov_area to
be transiently unmapped.
These are prerequisites for enabling KCOV on arm, but the issues
themsevles are generic -- we just happen to avoid them by chance rather
than design on x86-64 and arm64.
This patch (of 3):
For kernels built with CONFIG_PREEMPT, some C code may execute before or
after the interrupt handler, while the hardirq count is zero. In these
cases, in_task() can return true.
A task can be interrupted in the middle of a KCOV_DISABLE ioctl while it
resets the task's kcov data via kcov_task_init(). Instrumented code
executed during this period will call __sanitizer_cov_trace_pc(), and as
in_task() returns true, will inspect t->kcov_mode before trying to write
to t->kcov_area.
In kcov_init_task() we update t->kcov_{mode,area,size} with plain stores,
which may be re-ordered, torn, etc. Thus __sanitizer_cov_trace_pc() may
see bogus values for any of these fields, and may attempt to write to
memory which is not mapped.
Let's avoid this by using WRITE_ONCE() to set t->kcov_mode, with a
barrier() to ensure this is ordered before we clear t->kov_{area,size}.
This ensures that any code execute while kcov_init_task() is preempted
will either see valid values for t->kcov_{area,size}, or will see that
t->kcov_mode is KCOV_MODE_DISABLED, and bail out without touching
t->kcov_area.
Link: http://lkml.kernel.org/r/20180504135535.53744-2-mark.rutland@arm.com
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9e25826ffc ]
Switchdev notifications for addition of SWITCHDEV_OBJ_ID_PORT_VLAN are
distributed not only on clean addition, but also when flags on an
existing VLAN are changed. mlxsw_sp_bridge_port_vlan_add() calls
mlxsw_sp_port_vlan_get() to get at the port_vlan in question, which
implicitly references the object. This then leads to discrepancies in
reference counting when the VLAN is removed. spectrum.c warns about the
problem when the module is removed:
[13578.493090] WARNING: CPU: 0 PID: 2454 at drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2973 mlxsw_sp_port_remove+0xfd/0x110 [mlxsw_spectrum]
[...]
[13578.627106] Call Trace:
[13578.629617] mlxsw_sp_fini+0x2a/0xe0 [mlxsw_spectrum]
[13578.634748] mlxsw_core_bus_device_unregister+0x3e/0x130 [mlxsw_core]
[13578.641290] mlxsw_pci_remove+0x13/0x40 [mlxsw_pci]
[13578.646238] pci_device_remove+0x31/0xb0
[13578.650244] device_release_driver_internal+0x14f/0x220
[13578.655562] driver_detach+0x32/0x70
[13578.659183] bus_remove_driver+0x47/0xa0
[13578.663134] pci_unregister_driver+0x1e/0x80
[13578.667486] mlxsw_sp_module_exit+0xc/0x3fa [mlxsw_spectrum]
[13578.673207] __x64_sys_delete_module+0x13b/0x1e0
[13578.677888] ? exit_to_usermode_loop+0x78/0x80
[13578.682374] do_syscall_64+0x39/0xe0
[13578.685976] entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fix by putting the port_vlan when mlxsw_sp_port_vlan_bridge_join()
determines it's a flag-only change.
Fixes: b3529af6bb ("spectrum: Reference count VLAN entries")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b0eb6b41a upstream.
Arnd reports the following arm64 randconfig build error with the PSI
patches that add another page flag:
/git/arm-soc/arch/arm64/mm/init.c: In function 'mem_init':
/git/arm-soc/include/linux/compiler.h:357:38: error: call to
'__compiletime_assert_618' declared with attribute error: BUILD_BUG_ON
failed: sizeof(struct page) > (1 << STRUCT_PAGE_MAX_SHIFT)
The additional page flag causes other information stored in
page->flags to get bumped into their own struct page member:
#if SECTIONS_WIDTH+ZONES_WIDTH+NODES_SHIFT+LAST_CPUPID_SHIFT <=
BITS_PER_LONG - NR_PAGEFLAGS
#define LAST_CPUPID_WIDTH LAST_CPUPID_SHIFT
#else
#define LAST_CPUPID_WIDTH 0
#endif
#if defined(CONFIG_NUMA_BALANCING) && LAST_CPUPID_WIDTH == 0
#define LAST_CPUPID_NOT_IN_PAGE_FLAGS
#endif
which in turn causes the struct page size to exceed the size set in
STRUCT_PAGE_MAX_SHIFT. This value is an an estimate used to size the
VMEMMAP page array according to address space and struct page size.
However, the check is performed - and triggers here - on a !VMEMMAP
config, which consumes an additional 22 page bits for the sparse
section id. When VMEMMAP is enabled, those bits are returned, cpupid
doesn't need its own member, and the page passes the VMEMMAP check.
Restrict that check to the situation it was meant to check: that we
are sizing the VMEMMAP page array correctly.
Says Arnd:
Further experiments show that the build error already existed before,
but was only triggered with larger values of CONFIG_NR_CPU and/or
CONFIG_NODES_SHIFT that might be used in actual configurations but
not in randconfig builds.
With longer CPU and node masks, I could recreate the problem with
kernels as old as linux-4.7 when arm64 NUMA support got added.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Arnd Bergmann <arnd@arndb.de>
Cc: stable@vger.kernel.org
Fixes: 1a2db30034 ("arm64, numa: Add NUMA support for arm64 platforms.")
Fixes: 3e1907d5bf ("arm64: mm: move vmemmap region right below the linear region")
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2519c1bbe3 upstream.
Commit 57ea2a34ad ("tracing/kprobes: Fix trace_probe flags on
enable_trace_kprobe() failure") added an if statement that depends on another
if statement that gcc doesn't see will initialize the "link" variable and
gives the warning:
"warning: 'link' may be used uninitialized in this function"
It is really a false positive, but to quiet the warning, and also to make
sure that it never actually is used uninitialized, initialize the "link"
variable to NULL and add an if (!WARN_ON_ONCE(!link)) where the compiler
thinks it could be used uninitialized.
Cc: stable@vger.kernel.org
Fixes: 57ea2a34ad ("tracing/kprobes: Fix trace_probe flags on enable_trace_kprobe() failure")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3e536e222f upstream.
There is a window for racing when printing directly to task->comm,
allowing other threads to see a non-terminated string. The vsnprintf
function fills the buffer, counts the truncated chars, then finally
writes the \0 at the end.
creator other
vsnprintf:
fill (not terminated)
count the rest trace_sched_waking(p):
... memcpy(comm, p->comm, TASK_COMM_LEN)
write \0
The consequences depend on how 'other' uses the string. In our case,
it was copied into the tracing system's saved cmdlines, a buffer of
adjacent TASK_COMM_LEN-byte buffers (note the 'n' where 0 should be):
crash-arm64> x/1024s savedcmd->saved_cmdlines | grep 'evenk'
0xffffffd5b3818640: "irq/497-pwr_evenkworker/u16:12"
...and a strcpy out of there would cause stack corruption:
[224761.522292] Kernel panic - not syncing: stack-protector:
Kernel stack is corrupted in: ffffff9bf9783c78
crash-arm64> kbt | grep 'comm\|trace_print_context'
#6 0xffffff9bf9783c78 in trace_print_context+0x18c(+396)
comm (char [16]) = "irq/497-pwr_even"
crash-arm64> rd 0xffffffd4d0e17d14 8
ffffffd4d0e17d14: 2f71726900000000 5f7277702d373934 ....irq/497-pwr_
ffffffd4d0e17d24: 726f776b6e657665 3a3631752f72656b evenkworker/u16:
ffffffd4d0e17d34: f9780248ff003231 cede60e0ffffff9b 12..H.x......`..
ffffffd4d0e17d44: cede60c8ffffffd4 00000fffffffffd4 .....`..........
The workaround in e09e28671 (use strlcpy in __trace_find_cmdline) was
likely needed because of this same bug.
Solved by vsnprintf:ing to a local buffer, then using set_task_comm().
This way, there won't be a window where comm is not terminated.
Link: http://lkml.kernel.org/r/20180726071539.188015-1-snild@sony.com
Cc: stable@vger.kernel.org
Fixes: bc0c38d139 ("ftrace: latency tracer infrastructure")
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Snild Dolkow <snild@sony.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 15cc78644d upstream.
There was a case that triggered a double free in event_trigger_callback()
due to the called reg() function freeing the trigger_data and then it
getting freed again by the error return by the caller. The solution there
was to up the trigger_data ref count.
Code inspection found that event_enable_trigger_func() has the same issue,
but is not as easy to trigger (requires harder to trigger failures). It
needs to be solved slightly different as it needs more to clean up when the
reg() function fails.
Link: http://lkml.kernel.org/r/20180725124008.7008e586@gandalf.local.home
Cc: stable@vger.kernel.org
Fixes: 7862ad1846 ("tracing: Add 'enable_event' and 'disable_event' event trigger commands")
Reivewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1863c38725 upstream.
Running the following:
# cd /sys/kernel/debug/tracing
# echo 500000 > buffer_size_kb
[ Or some other number that takes up most of memory ]
# echo snapshot > events/sched/sched_switch/trigger
Triggers the following bug:
------------[ cut here ]------------
kernel BUG at mm/slub.c:296!
invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC PTI
CPU: 6 PID: 6878 Comm: bash Not tainted 4.18.0-rc6-test+ #1066
Hardware name: Hewlett-Packard HP Compaq Pro 6300 SFF/339A, BIOS K01 v03.03 07/14/2016
RIP: 0010:kfree+0x16c/0x180
Code: 05 41 0f b6 72 51 5b 5d 41 5c 4c 89 d7 e9 ac b3 f8 ff 48 89 d9 48 89 da 41 b8 01 00 00 00 5b 5d 41 5c 4c 89 d6 e9 f4 f3 ff ff <0f> 0b 0f 0b 48 8b 3d d9 d8 f9 00 e9 c1 fe ff ff 0f 1f 40 00 0f 1f
RSP: 0018:ffffb654436d3d88 EFLAGS: 00010246
RAX: ffff91a9d50f3d80 RBX: ffff91a9d50f3d80 RCX: ffff91a9d50f3d80
RDX: 00000000000006a4 RSI: ffff91a9de5a60e0 RDI: ffff91a9d9803500
RBP: ffffffff8d267c80 R08: 00000000000260e0 R09: ffffffff8c1a56be
R10: fffff0d404543cc0 R11: 0000000000000389 R12: ffffffff8c1a56be
R13: ffff91a9d9930e18 R14: ffff91a98c0c2890 R15: ffffffff8d267d00
FS: 00007f363ea64700(0000) GS:ffff91a9de580000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000055c1cacc8e10 CR3: 00000000d9b46003 CR4: 00000000001606e0
Call Trace:
event_trigger_callback+0xee/0x1d0
event_trigger_write+0xfc/0x1a0
__vfs_write+0x33/0x190
? handle_mm_fault+0x115/0x230
? _cond_resched+0x16/0x40
vfs_write+0xb0/0x190
ksys_write+0x52/0xc0
do_syscall_64+0x5a/0x160
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x7f363e16ab50
Code: 73 01 c3 48 8b 0d 38 83 2c 00 f7 d8 64 89 01 48 83 c8 ff c3 66 0f 1f 44 00 00 83 3d 79 db 2c 00 00 75 10 b8 01 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 31 c3 48 83 ec 08 e8 1e e3 01 00 48 89 04 24
RSP: 002b:00007fff9a4c6378 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 0000000000000009 RCX: 00007f363e16ab50
RDX: 0000000000000009 RSI: 000055c1cacc8e10 RDI: 0000000000000001
RBP: 000055c1cacc8e10 R08: 00007f363e435740 R09: 00007f363ea64700
R10: 0000000000000073 R11: 0000000000000246 R12: 0000000000000009
R13: 0000000000000001 R14: 00007f363e4345e0 R15: 00007f363e4303c0
Modules linked in: ip6table_filter ip6_tables snd_hda_codec_hdmi snd_hda_codec_realtek snd_hda_codec_generic snd_hda_intel snd_hda_codec snd_hwdep snd_hda_core snd_seq snd_seq_device i915 snd_pcm snd_timer i2c_i801 snd soundcore i2c_algo_bit drm_kms_helper
86_pkg_temp_thermal video kvm_intel kvm irqbypass wmi e1000e
---[ end trace d301afa879ddfa25 ]---
The cause is because the register_snapshot_trigger() call failed to
allocate the snapshot buffer, and then called unregister_trigger()
which freed the data that was passed to it. Then on return to the
function that called register_snapshot_trigger(), as it sees it
failed to register, it frees the trigger_data again and causes
a double free.
By calling event_trigger_init() on the trigger_data (which only ups
the reference counter for it), and then event_trigger_free() afterward,
the trigger_data would not get freed by the registering trigger function
as it would only up and lower the ref count for it. If the register
trigger function fails, then the event_trigger_free() called after it
will free the trigger data normally.
Link: http://lkml.kernel.org/r/20180724191331.738eb819@gandalf.local.home
Cc: stable@vger.kerne.org
Fixes: 93e31ffbf4 ("tracing: Add 'snapshot' event trigger command")
Reported-by: Masami Hiramatsu <mhiramat@kernel.org>
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b512719f77 upstream.
While forking, if delayacct init fails due to memory shortage, it
continues expecting all delayacct users to check task->delays pointer
against NULL before dereferencing it, which all of them used to do.
Commit c96f5471ce ("delayacct: Account blkio completion on the correct
task"), while updating delayacct_blkio_end() to take the target task
instead of always using %current, made the function test NULL on
%current->delays and then continue to operated on @p->delays. If
%current succeeded init while @p didn't, it leads to the following
crash.
BUG: unable to handle kernel NULL pointer dereference at 0000000000000004
IP: __delayacct_blkio_end+0xc/0x40
PGD 8000001fd07e1067 P4D 8000001fd07e1067 PUD 1fcffbb067 PMD 0
Oops: 0000 [#1] SMP PTI
CPU: 4 PID: 25774 Comm: QIOThread0 Not tainted 4.16.0-9_fbk1_rc2_1180_g6b593215b4d7 #9
RIP: 0010:__delayacct_blkio_end+0xc/0x40
Call Trace:
try_to_wake_up+0x2c0/0x600
autoremove_wake_function+0xe/0x30
__wake_up_common+0x74/0x120
wake_up_page_bit+0x9c/0xe0
mpage_end_io+0x27/0x70
blk_update_request+0x78/0x2c0
scsi_end_request+0x2c/0x1e0
scsi_io_completion+0x20b/0x5f0
blk_mq_complete_request+0xa2/0x100
ata_scsi_qc_complete+0x79/0x400
ata_qc_complete_multiple+0x86/0xd0
ahci_handle_port_interrupt+0xc9/0x5c0
ahci_handle_port_intr+0x54/0xb0
ahci_single_level_irq_intr+0x3b/0x60
__handle_irq_event_percpu+0x43/0x190
handle_irq_event_percpu+0x20/0x50
handle_irq_event+0x2a/0x50
handle_edge_irq+0x80/0x1c0
handle_irq+0xaf/0x120
do_IRQ+0x41/0xc0
common_interrupt+0xf/0xf
Fix it by updating delayacct_blkio_end() check @p->delays instead.
Link: http://lkml.kernel.org/r/20180724175542.GP1934745@devbig577.frc2.facebook.com
Fixes: c96f5471ce ("delayacct: Account blkio completion on the correct task")
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Dave Jones <dsj@fb.com>
Debugged-by: Dave Jones <dsj@fb.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Josh Snyder <joshs@netflix.com>
Cc: <stable@vger.kernel.org> [4.15+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 15d36fecd0 upstream.
When pmem namespaces created are smaller than section size, this can
cause an issue during removal and gpf was observed:
general protection fault: 0000 1 SMP PTI
CPU: 36 PID: 3941 Comm: ndctl Tainted: G W 4.14.28-1.el7uek.x86_64 #2
task: ffff88acda150000 task.stack: ffffc900233a4000
RIP: 0010:__put_page+0x56/0x79
Call Trace:
devm_memremap_pages_release+0x155/0x23a
release_nodes+0x21e/0x260
devres_release_all+0x3c/0x48
device_release_driver_internal+0x15c/0x207
device_release_driver+0x12/0x14
unbind_store+0xba/0xd8
drv_attr_store+0x27/0x31
sysfs_kf_write+0x3f/0x46
kernfs_fop_write+0x10f/0x18b
__vfs_write+0x3a/0x16d
vfs_write+0xb2/0x1a1
SyS_write+0x55/0xb9
do_syscall_64+0x79/0x1ae
entry_SYSCALL_64_after_hwframe+0x3d/0x0
Add code to check whether we have a mapping already in the same section
and prevent additional mappings from being created if that is the case.
Link: http://lkml.kernel.org/r/152909478401.50143.312364396244072931.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Robert Elliott <elliott@hpe.com>
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 384cf4285b upstream.
The Lenovo LaVie Z laptop requires i8042 to be reset in order to
consistently detect its Elantech touchpad. The nomux and kbdreset
quirks are not sufficient.
It's possible the other LaVie Z models from NEC require this as well.
Cc: stable@vger.kernel.org
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e935dba111 upstream.
Since Linux v4.10 release (commit 1d9174fbc5 "PM / Runtime: Defer
resuming of the device in pm_runtime_force_resume()"),
pm_runtime_force_resume() function doesn't runtime resume device if it was
not runtime active before system suspend. Thus, driver should not do any
register access after pm_runtime_force_resume() without checking the
runtime status of the device. To fix this issue, simply move
s3c64xx_spi_hwinit() call to s3c64xx_spi_runtime_resume() to ensure that
hardware is always properly initialized. This fixes Synchronous external
abort issue on system suspend/resume cycle on newer Exynos SoCs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 393753b217 upstream.
Inside m_can_chip_config(), when setting up the new value of the CCCR,
the CCCR_NISO bit is not cleared like the others, CCCR_TEST, CCCR_MON,
CCCR_BRSE and CCCR_FDOE, before checking the can.ctrlmode bits for
CAN_CTRLMODE_FD_NON_ISO.
This way once the controller was configured for CAN_CTRLMODE_FD_NON_ISO,
this mode could never be cleared again.
This fix is only relevant for controllers with version 3.1.x or 3.2.x.
Older versions do not support NISO.
Signed-off-by: Roman Fietze <roman.fietze@telemotive.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1675bee3e7 upstream.
pm_runtime_get_sync() returns a 1 if the state of the device is already
'active'. This is not a failure case and should return a success.
Therefore fix error handling for pm_runtime_get_sync() call such that
it returns success when the value is 1.
Also cleanup the TODO for using runtime PM for sleep mode as that is
implemented.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Cc: <stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d4c94ed9f upstream.
The DMA logic in firmwares < v3.3.0 embedded in the PCAN-PCIe FD cards
family is not capable of handling a mix of 32-bit and 64-bit logical
addresses. If the board is equipped with 2 or 4 CAN ports, then such a
situation might lead to a PCIe Bus Error "Malformed TLP" packet
as well as "irq xx: nobody cared" issue.
This patch adds a workaround that requests only 32-bit DMA addresses
when these might be allocated outside of the 4 GB area.
This issue has been fixed in firmware v3.3.0 and next.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8399799725 upstream.
RX overflow interrupt (RXOFLW) is disabled even though xcan_interrupt()
processes it. This means that an RX overflow interrupt will only be
processed when another interrupt gets asserted (e.g. for RX/TX).
Fix that by enabling the RXOFLW interrupt.
Fixes: b1201e44f5 ("can: xilinx CAN controller support")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f4f0f338c upstream.
xcan_interrupt() clears ERROR|RXOFLV|BSOFF|ARBLST interrupts if any of
them is asserted. This does not take into account that some of them
could have been asserted between interrupt status read and interrupt
clear, therefore clearing them without handling them.
Fix the code to only clear those interrupts that it knows are asserted
and therefore going to be processed in xcan_err_interrupt().
Fixes: b1201e44f5 ("can: xilinx CAN controller support")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 620050d9c2 upstream.
The xilinx_can driver assumes that the TXOK interrupt only clears after
it has been acknowledged as many times as there have been successfully
sent frames.
However, the documentation does not mention such behavior, instead
saying just that the interrupt is cleared when the clear bit is set.
Similarly, testing seems to also suggest that it is immediately cleared
regardless of the amount of frames having been sent. Performing some
heavy TX load and then going back to idle has the tx_head drifting
further away from tx_tail over time, steadily reducing the amount of
frames the driver keeps in the TX FIFO (but not to zero, as the TXOK
interrupt always frees up space for 1 frame from the driver's
perspective, so frames continue to be sent) and delaying the local echo
frames.
The TX FIFO tracking is also otherwise buggy as it does not account for
TX FIFO being cleared after software resets, causing
BUG!, TX FIFO full when queue awake!
messages to be output.
There does not seem to be any way to accurately track the state of the
TX FIFO for local echo support while using the full TX FIFO.
The Zynq version of the HW (but not the soft-AXI version) has watermark
programming support and with it an additional TX-FIFO-empty interrupt
bit.
Modify the driver to only put 1 frame into TX FIFO at a time on soft-AXI
and 2 frames at a time on Zynq. On Zynq the TXFEMP interrupt bit is used
to detect whether 1 or 2 frames have been sent at interrupt processing
time.
Tested with the integrated CAN on Zynq-7000 SoC. The 1-frame-FIFO mode
was also tested.
An alternative way to solve this would be to drop local echo support but
keep using the full TX FIFO.
v2: Add FIFO space check before TX queue wake with locking to
synchronize with queue stop. This avoids waking the queue when xmit()
had just filled it.
v3: Keep local echo support and reduce the amount of frames in FIFO
instead as suggested by Marc Kleine-Budde.
Fixes: b1201e44f5 ("can: xilinx CAN controller support")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2574fe5451 upstream.
The xilinx_can driver performs a software reset when an RX overrun is
detected. This causes the device to enter Configuration mode where no
messages are received or transmitted.
The documentation does not mention any need to perform a reset on an RX
overrun, and testing by inducing an RX overflow also indicated that the
device continues to work just fine without a reset.
Remove the software reset.
Tested with the integrated CAN on Zynq-7000 SoC.
Fixes: b1201e44f5 ("can: xilinx CAN controller support")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 877e0b7594 upstream.
The xilinx_can driver contains no mechanism for propagating recovery
from CAN_STATE_ERROR_WARNING and CAN_STATE_ERROR_PASSIVE.
Add such a mechanism by factoring the handling of
XCAN_STATE_ERROR_PASSIVE and XCAN_STATE_ERROR_WARNING out of
xcan_err_interrupt and checking for recovery after RX and TX if the
interface is in one of those states.
Tested with the integrated CAN on Zynq-7000 SoC.
Fixes: b1201e44f5 ("can: xilinx CAN controller support")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ebd83bdb0 upstream.
There are several issues with the suspend/resume handling code of the
driver:
- The device is attached and detached in the runtime_suspend() and
runtime_resume() callbacks if the interface is running. However,
during xcan_chip_start() the interface is considered running,
causing the resume handler to incorrectly call netif_start_queue()
at the beginning of xcan_chip_start(), and on xcan_chip_start() error
return the suspend handler detaches the device leaving the user
unable to bring-up the device anymore.
- The device is not brought properly up on system resume. A reset is
done and the code tries to determine the bus state after that.
However, after reset the device is always in Configuration mode
(down), so the state checking code does not make sense and
communication will also not work.
- The suspend callback tries to set the device to sleep mode (low-power
mode which monitors the bus and brings the device back to normal mode
on activity), but then immediately disables the clocks (possibly
before the device reaches the sleep mode), which does not make sense
to me. If a clean shutdown is wanted before disabling clocks, we can
just bring it down completely instead of only sleep mode.
Reorganize the PM code so that only the clock logic remains in the
runtime PM callbacks and the system PM callbacks contain the device
bring-up/down logic. This makes calling the runtime PM callbacks during
e.g. xcan_chip_start() safe.
The system PM callbacks now simply call common code to start/stop the
HW if the interface was running, replacing the broken code from before.
xcan_chip_stop() is updated to use the common reset code so that it will
wait for the reset to complete. Reset also disables all interrupts so do
not do that separately.
Also, the device_may_wakeup() checks are removed as the driver does not
have wakeup support.
Tested on Zynq-7000 integrated CAN.
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 32852c561b upstream.
If the device gets into a state where RXNEMP (RX FIFO not empty)
interrupt is asserted without RXOK (new frame received successfully)
interrupt being asserted, xcan_rx_poll() will continue to try to clear
RXNEMP without actually reading frames from RX FIFO. If the RX FIFO is
not empty, the interrupt will not be cleared and napi_schedule() will
just be called again.
This situation can occur when:
(a) xcan_rx() returns without reading RX FIFO due to an error condition.
The code tries to clear both RXOK and RXNEMP but RXNEMP will not clear
due to a frame still being in the FIFO. The frame will never be read
from the FIFO as RXOK is no longer set.
(b) A frame is received between xcan_rx_poll() reading interrupt status
and clearing RXOK. RXOK will be cleared, but RXNEMP will again remain
set as the new message is still in the FIFO.
I'm able to trigger case (b) by flooding the bus with frames under load.
There does not seem to be any benefit in using both RXNEMP and RXOK in
the way the driver does, and the polling example in the reference manual
(UG585 v1.10 18.3.7 Read Messages from RxFIFO) also says that either
RXOK or RXNEMP can be used for detecting incoming messages.
Fix the issue and simplify the RX processing by only using RXNEMP
without RXOK.
Tested with the integrated CAN on Zynq-7000 SoC.
Fixes: b1201e44f5 ("can: xilinx CAN controller support")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 722e5f2b1e upstream.
Commit 52cdbdd498 (driver core: correct device's shutdown order)
introduced a regression by breaking device shutdown on some systems.
Namely, the devices_kset_move_last() call in really_probe() added by
that commit is a mistake as it may cause parents to follow children
in the devices_kset list which then causes shutdown to fail. For
example, if a device has children before really_probe() is called
for it (which is not uncommon), that call will cause it to be
reordered after the children in the devices_kset list and the
ordering of that list will not reflect the correct device shutdown
order any more.
Also it causes the devices_kset list to be constantly reordered
until all drivers have been probed which is totally pointless
overhead in the majority of cases and it only covered an issue
with system shutdown, while system-wide suspend/resume potentially
had the same issue on the affected platforms (which was not covered).
Moreover, the shutdown issue originally addressed by the change in
really_probe() made by commit 52cdbdd498 is not present in 4.18-rc
any more, since dra7 started to use the sdhci-omap driver which
doesn't disable any regulators during shutdown, so the really_probe()
part of commit 52cdbdd498 can be safely reverted. [The original
issue was related to the omap_hsmmc driver used by dra7 previously.]
For the above reasons, revert the really_probe() modifications made
by commit 52cdbdd498.
The other code changes made by commit 52cdbdd498 are useful and
they need not be reverted.
Fixes: 52cdbdd498 (driver core: correct device's shutdown order)
Link: https://lore.kernel.org/lkml/CAFgQCTt7VfqM=UyCnvNFxrSw8Z6cUtAi3HUwR4_xPAc03SgHjQ@mail.gmail.com/
Reported-by: Pingfan Liu <kernelfans@gmail.com>
Tested-by: Pingfan Liu <kernelfans@gmail.com>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 73c2a01c52 upstream.
The dispatcher and the executer process the parse nodes During table
load. Error status from the evaluation confuses the AML parser. This
results in the parser failing to complete parsing of the current
scope op which becomes problematic. For the incorrect AML below, _ADR
never gets created.
definition_block(...)
{
Scope (\_SB)
{
Device (PCI0){...}
Name (OBJ1, 0x0)
OBJ1 = PCI0 + 5 // Results in an operand error.
} // \_SB not closed
// parser looks for \_SB._SB.PCI0, results in AE_NOT_FOUND error
// Entire scope block gets skipped.
Scope (\_SB.PCI0)
{
Name (_ADR, 0x0)
}
}
Fix the above error by properly completing the initial \_SB scope
after an error by clearing errors that occur during table load. In
the above case, this means that OBJ1 = PIC0 + 5 is skipped.
Fixes: 5088814a6e (ACPICA: AML parser: attempt to continue loading table after error)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200363
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Cc: 4.17+ <stable@vger.kernel.org> # 4.17+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4d644abf25 upstream.
Commit 1b9ba000 ("Allow function drivers to pause control
transfers") states that USB_GADGET_DELAYED_STATUS is only
supported if data phase is 0 bytes.
It seems that when the length is not 0 bytes, there is no
need to explicitly delay the data stage since the transfer
is not completed until the user responds. However, when the
length is 0, there is no data stage and the transfer is
finished once setup() returns, hence there is a need to
explicitly delay completion.
This manifests as the following bugs:
Prior to 946ef68ad4 ('Let setup() return
USB_GADGET_DELAYED_STATUS'), when setup is 0 bytes, ffs
would require user to queue a 0 byte request in order to
clear setup state. However, that 0 byte request was actually
not needed and would hang and cause errors in other setup
requests.
After the above commit, 0 byte setups work since the gadget
now accepts empty queues to ep0 to clear the delay, but all
other setups hang.
Fixes: 946ef68ad4 ("Let setup() return USB_GADGET_DELAYED_STATUS")
Signed-off-by: Jerry Zhang <zhangjerry@google.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 50b9773c13 upstream.
The current code is broken as it re-defines "req" inside the
if block, then goto out of it. Thus the request that ends
up being sent is not the one that was populated by the
code in question.
This fixes RNDIS driver autodetect by Windows 10 for me.
The bug was introduced by Chris rework to remove the local
queuing inside the if { } block of the redefined request.
Fixes: 636ba13aec ("usb: gadget: composite: remove duplicated code in OS desc handling")
Cc: <stable@vger.kernel.org> # v4.17
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 56406e017a upstream.
The commit 3bc04e28a0 ("usb: dwc2: host: Get aligned DMA in a more
supported way") introduced a common way to align DMA allocations.
The code in the commit aligns the struct dma_aligned_buffer but the
actual DMA address pointed by data[0] gets aligned to an offset from
the allocated boundary by the kmalloc_ptr and the old_xfer_buffer
pointers.
This is against the recommendation in Documentation/DMA-API.txt which
states:
Therefore, it is recommended that driver writers who don't take
special care to determine the cache line size at run time only map
virtual regions that begin and end on page boundaries (which are
guaranteed also to be cache line boundaries).
The effect of this is that architectures with non-coherent DMA caches
may run into memory corruption or kernel crashes with Unhandled
kernel unaligned accesses exceptions.
Fix the alignment by positioning the DMA area in front of the allocation
and use memory at the end of the area for storing the orginal
transfer_buffer pointer. This may have the added benefit of increased
performance as the DMA area is now fully aligned on all architectures.
Tested with Lantiq xRX200 (MIPS) and RPi Model B Rev 2 (ARM).
Fixes: 3bc04e28a0 ("usb: dwc2: host: Get aligned DMA in a more supported way")
Cc: <stable@vger.kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 249a32b7ee upstream.
Based on USB2.0 Spec Section 11.12.5,
"If a hub has per-port power switching and per-port current limiting,
an over-current on one port may still cause the power on another port
to fall below specific minimums. In this case, the affected port is
placed in the Power-Off state and C_PORT_OVER_CURRENT is set for the
port, but PORT_OVER_CURRENT is not set."
so let's check C_PORT_OVER_CURRENT too for over current condition.
Fixes: 08d1dec6f4 ("usb:hub set hub->change_bits when over-current happens")
Cc: <stable@vger.kernel.org>
Tested-by: Alessandro Antenucci <antenucci@korg.it>
Signed-off-by: Bin Liu <b-liu@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b96fba8d58 upstream.
If softsynthx_read() is called with `count < 3`, `count - 3` wraps, causing
the loop to copy as much data as available to the provided buffer. If
softsynthx_read() is invoked through sys_splice(), this causes an
unbounded kernel write; but even when userspace just reads from it
normally, a small size could cause userspace crashes.
Fixes: 425e586cf9 ("speakup: add unicode variant of /dev/softsynth")
Cc: stable@vger.kernel.org
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 69a1d98c83 upstream.
Commit b83b8b1881 ("staging:r8188eu: Use lib80211 to support TKIP")
is causing 2 problems for me:
1) One boot the wifi on a laptop with a r8188eu wifi device would not
connect and dmesg contained an oops about scheduling while atomic
pointing to the tkip code. This went away after reverting the commit.
2) I reverted the revert to try and get the oops from 1. again to be able
to add it to this commit message. But now the system did connect to the
wifi only to print a whole bunch of oopses, followed by a hardfreeze a
few seconds later. Subsequent reboots also all lead to scenario 2. Until
I reverted the commit again.
Revert the commit fixes both issues making the laptop usable again.
Fixes: b83b8b1881 ("staging:r8188eu: Use lib80211 to support TKIP")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ivan Safonov <insafonov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 58152ecbbc ]
In case skb in out_or_order_queue is the result of
multiple skbs coalescing, we would like to get a proper gso_segs
counter tracking, so that future tcp_drop() can report an accurate
number.
I chose to not implement this tracking for skbs in receive queue,
since they are not dropped, unless socket is disconnected.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8541b21e78 ]
In order to be able to give better diagnostics and detect
malicious traffic, we need to have better sk->sk_drops tracking.
Fixes: 9f5afeae51 ("tcp: use an RB tree for ooo receive queue")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3d4bf93ac1 ]
In case an attacker feeds tiny packets completely out of order,
tcp_collapse_ofo_queue() might scan the whole rb-tree, performing
expensive copies, but not changing socket memory usage at all.
1) Do not attempt to collapse tiny skbs.
2) Add logic to exit early when too many tiny skbs are detected.
We prefer not doing aggressive collapsing (which copies packets)
for pathological flows, and revert to tcp_prune_ofo_queue() which
will be less expensive.
In the future, we might add the possibility of terminating flows
that are proven to be malicious.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f4a3313d8e ]
Right after a TCP flow is created, receiving tiny out of order
packets allways hit the condition :
if (atomic_read(&sk->sk_rmem_alloc) >= sk->sk_rcvbuf)
tcp_clamp_window(sk);
tcp_clamp_window() increases sk_rcvbuf to match sk_rmem_alloc
(guarded by tcp_rmem[2])
Calling tcp_collapse_ofo_queue() in this case is not useful,
and offers a O(N^2) surface attack to malicious peers.
Better not attempt anything before full queue capacity is reached,
forcing attacker to spend lots of resource and allow us to more
easily detect the abuse.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 72cd43ba64 ]
Juha-Matti Tilli reported that malicious peers could inject tiny
packets in out_of_order_queue, forcing very expensive calls
to tcp_collapse_ofo_queue() and tcp_prune_ofo_queue() for
every incoming packet. out_of_order_queue rb-tree can contain
thousands of nodes, iterating over all of them is not nice.
Before linux-4.9, we would have pruned all packets in ofo_queue
in one go, every XXXX packets. XXXX depends on sk_rcvbuf and skbs
truesize, but is about 7000 packets with tcp_rmem[2] default of 6 MB.
Since we plan to increase tcp_rmem[2] in the future to cope with
modern BDP, can not revert to the old behavior, without great pain.
Strategy taken in this patch is to purge ~12.5 % of the queue capacity.
Fixes: 36a6503fed ("tcp: refine tcp_prune_ofo_queue() to not drop all packets")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Juha-Matti Tilli <juha-matti.tilli@iki.fi>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e99465b952 ]
Problem:
In vxlan_newlink, a default fdb entry is added before register_netdev.
The default fdb creation function also notifies user-space of the
fdb entry on the vxlan device which user-space does not know about yet.
(RTM_NEWNEIGH goes before RTM_NEWLINK for the same ifindex).
This patch fixes the user-space netlink notification ordering issue
with the following changes:
- decouple fdb notify from fdb create.
- Move fdb notify after register_netdev.
- Call rtnl_configure_link in vxlan newlink handler to notify
userspace about the newlink before fdb notify and
hence avoiding the user-space race.
Fixes: afbd8bae9c ("vxlan: add implicit fdb entry for default destination")
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7431016b10 ]
- Add new vxlan_fdb_alloc helper
- rename existing vxlan_fdb_create into vxlan_fdb_update:
because it really creates or updates an existing
fdb entry
- move new fdb creation into a separate vxlan_fdb_create
Main motivation for this change is to introduce the ability
to decouple vxlan fdb creation and notify, used in a later patch.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5025f7f7d5 ]
rtnl_configure_link sets dev->rtnl_link_state to
RTNL_LINK_INITIALIZED and unconditionally calls
__dev_notify_flags to notify user-space of dev flags.
current call sequence for rtnl_configure_link
rtnetlink_newlink
rtnl_link_ops->newlink
rtnl_configure_link (unconditionally notifies userspace of
default and new dev flags)
If a newlink handler wants to call rtnl_configure_link
early, we will end up with duplicate notifications to
user-space.
This patch fixes rtnl_configure_link to check rtnl_link_state
and call __dev_notify_flags with gchanges = 0 if already
RTNL_LINK_INITIALIZED.
Later in the series, this patch will help the following sequence
where a driver implementing newlink can call rtnl_configure_link
to initialize the link early.
makes the following call sequence work:
rtnetlink_newlink
rtnl_link_ops->newlink (vxlan) -> rtnl_configure_link (initializes
link and notifies
user-space of default
dev flags)
rtnl_configure_link (updates dev flags if requested by user ifm
and notifies user-space of new dev flags)
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 33180bee86 ]
When driver converts HW timestamp to wall clock time it subtracts
the last saved cycle counter from the HW timestamp and converts the
difference to nanoseconds.
The conversion is done by multiplying the cycles difference with the
clock multiplier value as a first step and therefore the cycles
difference should be small enough so that the multiplication product
doesn't exceed 64bit.
The overflow handling routine is in charge of updating the last saved
cycle counter in driver and it is called periodically using kernel
delayed workqueue.
The delay period for this work is calculated using the max HW cycle
counter value (a 41 bit mask) as a base which doesn't take the 64bit
limit into account so the delay period may be incorrect and too
long to prevent a large difference between the HW counter and the last
saved counter in SW.
This change adjusts the work period for the HW clock overflow work by
taking the minimum between the previous value and the quotient of max
u64 value and the clock multiplier value.
Fixes: ef9814deaf ("net/mlx5e: Add HW timestamping (TS) support")
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 24b711edfc ]
Example setup:
host: ip -6 addr add dev eth1 2001:db8:104::4
where eth1 is enslaved to a VRF
switch: ip -6 ro add 2001:db8:104::4/128 dev br1
where br1 only has an LLA
ping6 2001:db8:104::4
ssh 2001:db8:104::4
(NOTE: UDP works fine if the PKTINFO has the address set to the global
address and ifindex is set to the index of eth1 with a destination an
LLA).
For ICMP, icmp6_iif needs to be updated to check if skb->dev is an
L3 master. If it is then return the ifindex from rt6i_idev similar
to what is done for loopback.
For TCP, restore the original tcp_v6_iif definition which is needed in
most places and add a new tcp_v6_iif_l3_slave that considers the
l3_slave variability. This latter check is only needed for socket
lookups.
Fixes: 9ff7438460 ("net: vrf: Handle ipv6 multicast and link-local addresses")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two scenarios that we will restore deleted records. The first is
when device down and up(or unmap/remap). In this scenario the new filter
mode is same with previous one. Because we get it from in_dev->mc_list and
we do not touch it during device down and up.
The other scenario is when a new socket join a group which was just delete
and not finish sending status reports. In this scenario, we should use the
current filter mode instead of restore old one. Here are 4 cases in total.
old_socket new_socket before_fix after_fix
IN(A) IN(A) ALLOW(A) ALLOW(A)
IN(A) EX( ) TO_IN( ) TO_EX( )
EX( ) IN(A) TO_EX( ) ALLOW(A)
EX( ) EX( ) TO_EX( ) TO_EX( )
Fixes: 24803f38a5 (igmp: do not remove igmp souce list info when set link down)
Fixes: 1666d49e1d (mld: do not remove mld souce list info when set link down)
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 215d08a85b ]
The situation described in the comment can occur also with
PHY_IGNORE_INTERRUPT, therefore change the condition to include it.
Fixes: f555f34fdc ("net: phy: fix auto-negotiation stall due to unavailable interrupt")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 144fe2bfd2 ]
Current sg coalescing logic in sk_alloc_sg() (latter is used by tls and
sockmap) is not quite correct in that we do fetch the previous sg entry,
however the subsequent check whether the refilled page frag from the
socket is still the same as from the last entry with prior offset and
length matching the start of the current buffer is comparing always the
first sg list entry instead of the prior one.
Fixes: 3c4d755915 ("tls: kernel TLS support")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b809ec869b ]
Previously only the neighbour state was checked to decide if an offloaded
entry should be removed. However, there can be situations when the entry
is dead but still marked as valid. This can lead to dead entries not
being removed from fw tables or even incorrect data being added.
Check the entry dead bit before deciding if it should be added to or
removed from fw neighbour tables.
Fixes: 8e6a9046b6 ("nfp: flower vxlan neighbour offload")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e279d634f3 ]
Removed an error message received when configuring ETS total
bandwidth to be zero.
Our hardware doesn't support such configuration, so we shall
reject it in the driver. Nevertheless, we removed the error message
in order to eliminate error messages caused by old userspace tools
who try to pass such configuration.
Fixes: ff0891915c ("net/mlx5e: Fix ETS BW check")
Signed-off-by: Shay Agroskin <shayag@mellanox.com>
Reviewed-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7e29392eee ]
We get egress rules through the egdev mechanism when the ingress device
is not supporting offload, with the expected use-case of tunnel decap
ingress rule set on shared tunnel device.
Make sure to offload egress/egdev rules only if decap action (tunnel key
unset) exists there and err otherwise.
Fixes: 717503b9cf ("net: sched: convert cls_flower->egress_dev users to tc_setup_cb_egdev infra")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 60bd4af814 ]
When an e-switch TC rule is offloaded through the egdev (egress
device) mechanism, we treat this as egress, all other cases (NIC
and e-switch) are considred ingress.
This is preparation step that will allow us to identify "wrong"
stat/del offload calls made by the TC core on egdev based flows and
ignore them.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fcf4793e27 ]
The current code does not check sk->sk_shutdown & RCV_SHUTDOWN.
tls_sw_recvmsg may return a positive value in the case where bytes have
already been copied when the socket is shutdown. sk->sk_err has been
cleared, causing the tls_wait_data to hang forever on a subsequent
invocation. Checking sk->sk_shutdown & RCV_SHUTDOWN, as in tcp_recvmsg,
fixes this problem.
Fixes: c46234ebb4 ("tls: RX path for ktls")
Acked-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: Doron Roberts-Kedes <doronrk@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 18041b5236 ]
Commit 7edf6d314c tried to resolve an inconsistency (BIOS WoL
settings are accepted, but device isn't wakeup-enabled) resulting
from a previous broken-BIOS workaround by making disabled WoL the
default.
This however had some side effects, most likely due to a broken BIOS
some systems don't properly resume from suspend when the MagicPacket
WoL bit isn't set in the chip, see
https://bugzilla.kernel.org/show_bug.cgi?id=200195
Therefore restore the WoL behavior from 4.16.
Reported-by: Albert Astals Cid <aacid@kde.org>
Fixes: 7edf6d314c ("r8169: disable WOL per default")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a0496ef2c2 ]
Per DCTCP RFC8257 (Section 3.2) the ACK reflecting the CE status change
has to be sent immediately so the sender can respond quickly:
""" When receiving packets, the CE codepoint MUST be processed as follows:
1. If the CE codepoint is set and DCTCP.CE is false, set DCTCP.CE to
true and send an immediate ACK.
2. If the CE codepoint is not set and DCTCP.CE is true, set DCTCP.CE
to false and send an immediate ACK.
"""
Previously DCTCP implementation may continue to delay the ACK. This
patch fixes that to implement the RFC by forcing an immediate ACK.
Tested with this packetdrill script provided by Larry Brakmo
0.000 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
0.000 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
0.000 setsockopt(3, SOL_TCP, TCP_CONGESTION, "dctcp", 5) = 0
0.000 bind(3, ..., ...) = 0
0.000 listen(3, 1) = 0
0.100 < [ect0] SEW 0:0(0) win 32792 <mss 1000,sackOK,nop,nop,nop,wscale 7>
0.100 > SE. 0:0(0) ack 1 <mss 1460,nop,nop,sackOK,nop,wscale 8>
0.110 < [ect0] . 1:1(0) ack 1 win 257
0.200 accept(3, ..., ...) = 4
+0 setsockopt(4, SOL_SOCKET, SO_DEBUG, [1], 4) = 0
0.200 < [ect0] . 1:1001(1000) ack 1 win 257
0.200 > [ect01] . 1:1(0) ack 1001
0.200 write(4, ..., 1) = 1
0.200 > [ect01] P. 1:2(1) ack 1001
0.200 < [ect0] . 1001:2001(1000) ack 2 win 257
+0.005 < [ce] . 2001:3001(1000) ack 2 win 257
+0.000 > [ect01] . 2:2(0) ack 2001
// Previously the ACK below would be delayed by 40ms
+0.000 > [ect01] E. 2:2(0) ack 3001
+0.500 < F. 9501:9501(0) ack 4 win 257
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 27cde44a25 ]
Currently when a DCTCP receiver delays an ACK and receive a
data packet with a different CE mark from the previous one's, it
sends two immediate ACKs acking previous and latest sequences
respectly (for ECN accounting).
Previously sending the first ACK may mark off the delayed ACK timer
(tcp_event_ack_sent). This may subsequently prevent sending the
second ACK to acknowledge the latest sequence (tcp_ack_snd_check).
The culprit is that tcp_send_ack() assumes it always acknowleges
the latest sequence, which is not true for the first special ACK.
The fix is to not make the assumption in tcp_send_ack and check the
actual ack sequence before cancelling the delayed ACK. Further it's
safer to pass the ack sequence number as a local variable into
tcp_send_ack routine, instead of intercepting tp->rcv_nxt to avoid
future bugs like this.
Reported-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b0c05d0e99 ]
Previously, when a data segment was sent an ACK was piggybacked
on the data segment without generating a CA_EVENT_NON_DELAYED_ACK
event to notify congestion control modules. So the DCTCP
ca->delayed_ack_reserved flag could incorrectly stay set when
in fact there were no delayed ACKs being reserved. This could result
in sending a special ECN notification ACK that carries an older
ACK sequence, when in fact there was no need for such an ACK.
DCTCP keeps track of the delayed ACK status with its own separate
state ca->delayed_ack_reserved. Previously it may accidentally cancel
the delayed ACK without updating this field upon sending a special
ACK that carries a older ACK sequence. This inconsistency would
lead to DCTCP receiver never acknowledging the latest data until the
sender times out and retry in some cases.
Packetdrill script (provided by Larry Brakmo)
0.000 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
0.000 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
0.000 setsockopt(3, SOL_TCP, TCP_CONGESTION, "dctcp", 5) = 0
0.000 bind(3, ..., ...) = 0
0.000 listen(3, 1) = 0
0.100 < [ect0] SEW 0:0(0) win 32792 <mss 1000,sackOK,nop,nop,nop,wscale 7>
0.100 > SE. 0:0(0) ack 1 <mss 1460,nop,nop,sackOK,nop,wscale 8>
0.110 < [ect0] . 1:1(0) ack 1 win 257
0.200 accept(3, ..., ...) = 4
0.200 < [ect0] . 1:1001(1000) ack 1 win 257
0.200 > [ect01] . 1:1(0) ack 1001
0.200 write(4, ..., 1) = 1
0.200 > [ect01] P. 1:2(1) ack 1001
0.200 < [ect0] . 1001:2001(1000) ack 2 win 257
0.200 write(4, ..., 1) = 1
0.200 > [ect01] P. 2:3(1) ack 2001
0.200 < [ect0] . 2001:3001(1000) ack 3 win 257
0.200 < [ect0] . 3001:4001(1000) ack 3 win 257
0.200 > [ect01] . 3:3(0) ack 4001
0.210 < [ce] P. 4001:4501(500) ack 3 win 257
+0.001 read(4, ..., 4500) = 4500
+0 write(4, ..., 1) = 1
+0 > [ect01] PE. 3:4(1) ack 4501
+0.010 < [ect0] W. 4501:5501(1000) ack 4 win 257
// Previously the ACK sequence below would be 4501, causing a long RTO
+0.040~+0.045 > [ect01] . 4:4(0) ack 5501 // delayed ack
+0.311 < [ect0] . 5501:6501(1000) ack 4 win 257 // More data
+0 > [ect01] . 4:4(0) ack 6501 // now acks everything
+0.500 < F. 9501:9501(0) ack 4 win 257
Reported-by: Larry Brakmo <brakmo@fb.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Lawrence Brakmo <brakmo@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f7482683f1 ]
The calculation of "wqe_size" is not correct when the tx queue is busy in
hinic_xmit_frame().
When there are no free WQEs, the tx flow will unmap the skb buffer, then
ring the doobell for the pending packets. But the "wqe_size" which used
to calculate the doorbell address is not correct. The wqe size should be
cleared to 0, otherwise, it will cause a doorbell error.
This patch fixes the problem.
Reported-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 958c696f5a ]
Function mlx4_RST2INIT_QP_wrapper saved the qp number passed in the qp
context, rather than the one passed in the input modifier.
However, the qp number in the qp context is not defined as a
required parameter by the FW. Therefore, drivers may choose to not
specify the qp number in the qp context for the reset-to-init transition.
Thus, we must save the qp number passed in the command input modifier --
which is always present. (This saved qp number is used as the input
modifier for command 2RST_QP when a slave's qp's are destroyed).
Fixes: c82e9aa0a8 ("mlx4_core: resource tracking for HCA resources used by guests")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3d82475ad4 ]
free_irq() waits until all handlers for this IRQ have completed. As the
relevant handler (mv88e6xxx_g1_irq_thread_fn()) takes the chip's reg_lock
it might never return if the thread calling free_irq() holds this lock.
For the same reason kthread_cancel_delayed_work_sync() in the polling case
must not hold this lock.
Also first free the irq (or stop the worker respectively) such that
mv88e6xxx_g1_irq_thread_work() isn't called any more before the irq
mappings are dropped in mv88e6xxx_g1_irq_free_common() to prevent the
worker thread to call handle_nested_irq(0) which results in a NULL-pointer
exception.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2efd4fca70 ]
Syzbot reported a read beyond the end of the skb head when returning
IPV6_ORIGDSTADDR:
BUG: KMSAN: kernel-infoleak in put_cmsg+0x5ef/0x860 net/core/scm.c:242
CPU: 0 PID: 4501 Comm: syz-executor128 Not tainted 4.17.0+ #9
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x185/0x1d0 lib/dump_stack.c:113
kmsan_report+0x188/0x2a0 mm/kmsan/kmsan.c:1125
kmsan_internal_check_memory+0x138/0x1f0 mm/kmsan/kmsan.c:1219
kmsan_copy_to_user+0x7a/0x160 mm/kmsan/kmsan.c:1261
copy_to_user include/linux/uaccess.h:184 [inline]
put_cmsg+0x5ef/0x860 net/core/scm.c:242
ip6_datagram_recv_specific_ctl+0x1cf3/0x1eb0 net/ipv6/datagram.c:719
ip6_datagram_recv_ctl+0x41c/0x450 net/ipv6/datagram.c:733
rawv6_recvmsg+0x10fb/0x1460 net/ipv6/raw.c:521
[..]
This logic and its ipv4 counterpart read the destination port from
the packet at skb_transport_offset(skb) + 4.
With MSG_MORE and a local SOCK_RAW sender, syzbot was able to cook a
packet that stores headers exactly up to skb_transport_offset(skb) in
the head and the remainder in a frag.
Call pskb_may_pull before accessing the pointer to ensure that it lies
in skb head.
Link: http://lkml.kernel.org/r/CAF=yD-LEJwZj5a1-bAAj2Oy_hKmGygV6rsJ_WOrAYnv-fnayiQ@mail.gmail.com
Reported-by: syzbot+9adb4b567003cac781f0@syzkaller.appspotmail.com
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3dd1c9a127 ]
The skb hash for locally generated ip[v6] fragments belonging
to the same datagram can vary in several circumstances:
* for connected UDP[v6] sockets, the first fragment get its hash
via set_owner_w()/skb_set_hash_from_sk()
* for unconnected IPv6 UDPv6 sockets, the first fragment can get
its hash via ip6_make_flowlabel()/skb_get_hash_flowi6(), if
auto_flowlabel is enabled
For the following frags the hash is usually computed via
skb_get_hash().
The above can cause OoO for unconnected IPv6 UDPv6 socket: in that
scenario the egress tx queue can be selected on a per packet basis
via the skb hash.
It may also fool flow-oriented schedulers to place fragments belonging
to the same datagram in different flows.
Fix the issue by copying the skb hash from the head frag into
the others at fragmentation time.
Before this commit:
perf probe -a "dev_queue_xmit skb skb->hash skb->l4_hash:b1@0/8 skb->sw_hash:b1@1/8"
netperf -H $IPV4 -t UDP_STREAM -l 5 -- -m 2000 -n &
perf record -e probe:dev_queue_xmit -e probe:skb_set_owner_w -a sleep 0.1
perf script
probe:dev_queue_xmit: (ffffffff8c6b1b20) hash=3713014309 l4_hash=1 sw_hash=0
probe:dev_queue_xmit: (ffffffff8c6b1b20) hash=0 l4_hash=0 sw_hash=0
After this commit:
probe:dev_queue_xmit: (ffffffff8c6b1b20) hash=2171763177 l4_hash=1 sw_hash=0
probe:dev_queue_xmit: (ffffffff8c6b1b20) hash=2171763177 l4_hash=1 sw_hash=0
Fixes: b73c3d0e4f ("net: Save TX flow hash in sock and set in skbuf on xmit")
Fixes: 67800f9b1f ("ipv6: Call skb_get_hash_flowi6 to get skb->hash in ip6_make_flowlabel")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c1f897ce18 ]
For some time now, if you load the bonding driver and configure bond
parameters via sysfs using minimal config options, such as specifying
nothing but the mode, relying on defaults for everything else, modes
that cannot use arp monitoring (802.3ad, balance-tlb, balance-alb) all
wind up with both arp_interval=0 (as it should be) and miimon=0, which
means the miimon monitor thread never actually runs. This is particularly
problematic for 802.3ad.
For example, from an LNST recipe I've set up:
$ modprobe bonding max_bonds=0"
$ echo "+t_bond0" > /sys/class/net/bonding_masters"
$ ip link set t_bond0 down"
$ echo "802.3ad" > /sys/class/net/t_bond0/bonding/mode"
$ ip link set ens1f1 down"
$ echo "+ens1f1" > /sys/class/net/t_bond0/bonding/slaves"
$ ip link set ens1f0 down"
$ echo "+ens1f0" > /sys/class/net/t_bond0/bonding/slaves"
$ ethtool -i t_bond0"
$ ip link set ens1f1 up"
$ ip link set ens1f0 up"
$ ip link set t_bond0 up"
$ ip addr add 192.168.9.1/24 dev t_bond0"
$ ip addr add 2002::1/64 dev t_bond0"
This bond comes up okay, but things look slightly suspect in
/proc/net/bonding/t_bond0 output:
$ grep -i mii /proc/net/bonding/t_bond0
MII Status: up
MII Polling Interval (ms): 0
MII Status: up
MII Status: up
Now, pull a cable on one of the ports in the bond, then reconnect it, and
you'll see:
Slave Interface: ens1f0
MII Status: down
Speed: 1000 Mbps
Duplex: full
I believe this became a major issue as of commit 4d2c0cda07, which for
802.3ad bonds, sets slave->link = BOND_LINK_DOWN, with a comment about
relying on link monitoring via miimon to set it correctly, but since the
miimon work queue never runs, the link just stays marked down.
If we simply tweak bond_option_mode_set() slightly, we can check for the
non-arp modes having no miimon value set, and insert BOND_DEFAULT_MIIMON,
which gets things back in full working order. This problem exists as far
back as 4.14, and might be worth fixing in all stable trees since, though
the work-around is to simply specify an miimon value yourself.
Reported-by: Bob Ball <ball@umich.edu>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c987ac6f1f upstream.
On Amlogic Meson GXBB & GXL platforms, the SCPI Cortex-M4 Co-Processor
seems to be dependent on the FCLK_DIV2 to be operationnal.
The issue occurred since v4.17-rc1 by freezing the kernel boot when
the 'schedutil' cpufreq governor was selected as default :
[ 12.071837] scpi_protocol scpi: SCP Protocol 0.0 Firmware 0.0.0 version
domain-0 init dvfs: 4
[ 12.087757] hctosys: unable to open rtc device (rtc0)
[ 12.087907] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 12.102241] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
But when disabling the MMC driver, the boot finished but cpufreq failed to
change the CPU frequency :
[ 12.153045] cpufreq: __target_index: Failed to change cpu frequency: -5
A bisect between v4.16 and v4.16-rc1 gave
05f814402d ("clk: meson: add fdiv clock gates") to be the first bad commit.
This commit added support for the missing clock gates before the fixed PLL
fixed dividers (FCLK_DIVx) and the clock framework basically disabled
all the unused fixed dividers, thus disabled a critical clock path for
the SCPI Co-Processor.
This patch simply sets the FCLK_DIV2 gate as critical to ensure
nobody can disable it.
Fixes: 05f814402d ("clk: meson: add fdiv clock gates")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
[few corrections in the commit description]
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eb493fbc15 upstream.
Currently nouveau doesn't actually expose the state debugfs file that's
usually provided for any modesetting driver that supports atomic, even
if nouveau is loaded with atomic=1. This is due to the fact that the
standard debugfs files that DRM creates for atomic drivers is called
when drm_get_pci_dev() is called from nouveau_drm.c. This happens well
before we've initialized the display core, which is currently
responsible for setting the DRIVER_ATOMIC cap.
So, move the atomic option into nouveau_drm.c and just add the
DRIVER_ATOMIC cap whenever it's enabled on the kernel commandline. This
shouldn't cause any actual issues, as the atomic ioctl will still fail
as expected even if the display core doesn't disable it until later in
the init sequence. This also provides the added benefit of being able to
use the state debugfs file to check the current display state even if
clients aren't allowed to modify it through anything other than the
legacy ioctls.
Additionally, disable the DRIVER_ATOMIC cap in nv04's display core, as
this was already disabled there previously.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 76fa4975f3 upstream.
A VM which has:
- a DMA capable device passed through to it (eg. network card);
- running a malicious kernel that ignores H_PUT_TCE failure;
- capability of using IOMMU pages bigger that physical pages
can create an IOMMU mapping that exposes (for example) 16MB of
the host physical memory to the device when only 64K was allocated to the VM.
The remaining 16MB - 64K will be some other content of host memory, possibly
including pages of the VM, but also pages of host kernel memory, host
programs or other VMs.
The attacking VM does not control the location of the page it can map,
and is only allowed to map as many pages as it has pages of RAM.
We already have a check in drivers/vfio/vfio_iommu_spapr_tce.c that
an IOMMU page is contained in the physical page so the PCI hardware won't
get access to unassigned host memory; however this check is missing in
the KVM fastpath (H_PUT_TCE accelerated code). We were lucky so far and
did not hit this yet as the very first time when the mapping happens
we do not have tbl::it_userspace allocated yet and fall back to
the userspace which in turn calls VFIO IOMMU driver, this fails and
the guest does not retry,
This stores the smallest preregistered page size in the preregistered
region descriptor and changes the mm_iommu_xxx API to check this against
the IOMMU page size.
This calculates maximum page size as a minimum of the natural region
alignment and compound page size. For the page shift this uses the shift
returned by find_linux_pte() which indicates how the page is mapped to
the current userspace - if the page is huge and this is not a zero, then
it is a leaf pte and the page is mapped within the range.
Fixes: 121f80ba68 ("KVM: PPC: VFIO: Add in-kernel acceleration for VFIO")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 565b9937f4 upstream.
The HPLL can be configured through a register (SCU24), however some
platforms chose to configure it through the strapping settings and do
not use the register. This was not noticed as the logic for bit 18 in
SCU24 was confused: set means programmed, but the driver read it as set
means strapped.
This gives us the correct HPLL value on Palmetto systems, from which
most of the peripheral clocks are generated.
Fixes: 5eda5d79e4 ("clk: Add clock driver for ASPEED BMC SoCs")
Cc: stable@vger.kernel.org # v4.15
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61c40f35f5 upstream.
Switching the CPU from the L2 or L3 frequencies (300 and 200 Mhz
respectively) to L0 frequency (1.2 Ghz) requires a significant amount
of time to let VDD stabilize to the appropriate voltage. This amount of
time is large enough that it cannot be covered by the hardware
countdown register. Due to this, the CPU might start operating at L0
before the voltage is stabilized, leading to CPU stalls.
To work around this problem, we prevent switching directly from the
L2/L3 frequencies to the L0 frequency, and instead switch to the L1
frequency in-between. The sequence therefore becomes:
1. First switch from L2/L3(200/300MHz) to L1(600MHZ)
2. Sleep 20ms for stabling VDD voltage
3. Then switch from L1(600MHZ) to L0(1200Mhz).
It is based on the work done by Ken Ma <make@marvell.com>
Cc: stable@vger.kernel.org
Fixes: 2089dc33ea ("clk: mvebu: armada-37xx-periph: add DVFS support for cpu clocks")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 38c0a74fe0 upstream.
The MIPS implementation of pci_resource_to_user() introduced in v3.12 by
commit 4c2924b725 ("MIPS: PCI: Use pci_resource_to_user to map pci
memory space properly") incorrectly sets *end to the address of the
byte after the resource, rather than the last byte of the resource.
This results in userland seeing resources as a byte larger than they
actually are, for example a 32 byte BAR will be reported by a tool such
as lspci as being 33 bytes in size:
Region 2: I/O ports at 1000 [disabled] [size=33]
Correct this by subtracting one from the calculated end address,
reporting the correct address to userland.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Reported-by: Rui Wang <rui.wang@windriver.com>
Fixes: 4c2924b725 ("MIPS: PCI: Use pci_resource_to_user to map pci memory space properly")
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org # v3.12+
Patchwork: https://patchwork.linux-mips.org/patch/19829/
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ec916f82c upstream.
This commit may cause a less than required dma mask to be used for
some allocations, which apparently leads to module load failures for
iwlwifi sometimes.
This reverts commit d657c5c73c.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Fabio Coatti <fabio.coatti@gmail.com>
Tested-by: Fabio Coatti <fabio.coatti@gmail.com>
Cc: "Jason A. Donenfeld" <Jason@zx2c4.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd28325249 upstream.
This lets userspace read the MSR_IA32_ARCH_CAPABILITIES and check that all
requested features are available on the host.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 229bc19fd7 upstream.
Don't rely on event interrupt (EINT) bit alone to detect pending port
change in resume. If no change event is detected the host may be suspended
again, oterwise roothubs are resumed.
There is a lag in xHC setting EINT. If we don't notice the pending change
in resume, and the controller is runtime suspeded again, it causes the
event handler to assume host is dead as it will fail to read xHC registers
once PCI puts the controller to D3 state.
[ 268.520969] xhci_hcd: xhci_resume: starting port polling.
[ 268.520985] xhci_hcd: xhci_hub_status_data: stopping port polling.
[ 268.521030] xhci_hcd: xhci_suspend: stopping port polling.
[ 268.521040] xhci_hcd: // Setting command ring address to 0x349bd001
[ 268.521139] xhci_hcd: Port Status Change Event for port 3
[ 268.521149] xhci_hcd: resume root hub
[ 268.521163] xhci_hcd: port resume event for port 3
[ 268.521168] xhci_hcd: xHC is not running.
[ 268.521174] xhci_hcd: handle_port_status: starting port polling.
[ 268.596322] xhci_hcd: xhci_hc_died: xHCI host controller not responding, assume dead
The EINT lag is described in a additional note in xhci specs 4.19.2:
"Due to internal xHC scheduling and system delays, there will be a lag
between a change bit being set and the Port Status Change Event that it
generated being written to the Event Ring. If SW reads the PORTSC and
sees a change bit set, there is no guarantee that the corresponding Port
Status Change Event has already been written into the Event Ring."
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f88a333b44 upstream.
kernel_wait4() expects a userland address for status - it's only
rusage that goes as a kernel one (and needs a copyout afterwards)
[ Also, fix the prototype of kernel_wait4() to have that __user
annotation - Linus ]
Fixes: 92ebce5ac5 ("osf_wait4: switch to kernel_wait4()")
Cc: stable@kernel.org # v4.13+
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5c968f4802 ]
mii_nway_restart is not pm aware which results in a rtnl deadlock.
Implement mii_nway_restart manual by setting BMCR_ANRESTART if
BMCR_ANENABLE is set.
To reproduce:
* plug an asix based usb network interface
* wait until the device enters PM (~5 sec)
* `ip link set eth1 up` will never return
Fixes: d9fe64e511 ("net: asix: Add in_pm parameter")
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e66515999b ]
Commit adc176c547 ("ipv6 addrconf: Implemented enhanced DAD (RFC7527)")
added enhanced DAD with a nonce length of 6 bytes. However, RFC7527
doesn't specify the length of the nonce, other than being 6 + 8*k bytes,
with integer k >= 0 (RFC3971 5.3.2). The current implementation simply
assumes that the nonce will always be 6 bytes, but others systems are
free to choose different sizes.
If another system sends a nonce of different length but with the same 6
bytes prefix, it shouldn't be considered as the same nonce. Thus, check
that the length of the received nonce is the same as the length we sent.
Ugly scapy test script running on veth0:
def loop():
pkt=sniff(iface="veth0", filter="icmp6", count=1)
pkt = pkt[0]
b = bytearray(pkt[Raw].load)
b[1] += 1
b += b'\xde\xad\xbe\xef\xde\xad\xbe\xef'
pkt[Raw].load = bytes(b)
pkt[IPv6].plen += 8
# fixup checksum after modifying the payload
pkt[IPv6].payload.cksum -= 0x3b44
if pkt[IPv6].payload.cksum < 0:
pkt[IPv6].payload.cksum += 0xffff
sendp(pkt, iface="veth0")
This should result in DAD failure for any address added to veth0's peer,
but is currently ignored.
Fixes: adc176c547 ("ipv6 addrconf: Implemented enhanced DAD (RFC7527)")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9e3bff9239 ]
SYSTEMPORT Lite reversed the logic compared to SYSTEMPORT, the
GIB_FCS_STRIP bit is set when the Ethernet FCS is stripped, and that bit
is not set by default. Fix the logic such that we properly check whether
that bit is set or not and we don't forward an extra 4 bytes to the
network stack.
Fixes: 44a4524c54 ("net: systemport: Add support for SYSTEMPORT Lite")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 432e629e56 ]
When a new rx packet arrives, the rx path will decide whether to reuse
the remainder of the page or not according to one of the below conditions:
1. frag_info->frag_stride == PAGE_SIZE / 2
2. frags->page_offset + frag_info->frag_size > PAGE_SIZE;
The first condition is no met for when XDP is set.
For XDP, page_offset is always set to priv->rx_headroom which is
XDP_PACKET_HEADROOM and frag_info->frag_size is around mtu size + some
padding, still the 2nd release condition will hold since
XDP_PACKET_HEADROOM + 1536 < PAGE_SIZE, as a result the page will not
be released and will be _wrongly_ reused for next free rx descriptor.
In XDP there is an assumption to have a page per packet and reuse can
break such assumption and might cause packet data corruptions.
Fix this by adding an extra condition (!priv->rx_headroom) to the 2nd
case to avoid page reuse when XDP is set, since rx_headroom is set to 0
for non XDP setup and set to XDP_PACKET_HEADROOM for XDP setup.
No additional cache line is required for the new condition.
Fixes: 34db548bfb ("mlx4: add page recycling in receive path")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Suggested-by: Martin KaFai Lau <kafai@fb.com>
CC: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 94b3b54230 ]
Setting up macvlan/macvtap networks over atlantic NIC results
in no traffic over these networks because ndo_set_rx_mode did
not listed UC MACs as registered in unicast filter.
Here we fix that taking into account maximum number of UC
filters supported by hardware. If more than MAX addresses were
registered, we just enable promisc and/or allmulti to pass
the traffic in.
We also remove MULTICAST_ADDRESS_MAX constant from aq_cfg since
thats not a configurable parameter at all.
Fixes: b21f502 ("net:ethernet:aquantia: Fix for multicast filter handling.")
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6b81b193b8 ]
If out ring is full temporarily and receive completion cannot go out,
we may still need to reschedule napi if certain conditions are met.
Otherwise the napi poll might be stopped forever, and cause network
disconnect.
Fixes: 7426b1a518 ("netvsc: optimize receive completions")
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a659254755 ]
After commit b6c5734db0 ("sctp: fix the handling of ICMP Frag Needed
for too small MTUs"), sctp_transport_update_pmtu would refetch pathmtu
from the dst and set it to transport's pathmtu without any check.
The new pathmtu may be lower than MINSEGMENT if the dst is obsolete and
updated by .get_dst() in sctp_transport_update_pmtu. In this case, it
could have a smaller MTU as well, and thus we should validate it
against MINSEGMENT instead.
Syzbot reported a warning in sctp_mtu_payload caused by this.
This patch refetches the pathmtu by calling sctp_dst_mtu where it does
the check against MINSEGMENT.
v1->v2:
- refetch the pathmtu by calling sctp_dst_mtu instead as Marcelo's
suggestion.
Fixes: b6c5734db0 ("sctp: fix the handling of ICMP Frag Needed for too small MTUs")
Reported-by: syzbot+f0d9d7cba052f9344b03@syzkaller.appspotmail.com
Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6ff0f871c2 ]
Which makes sure that the MTU respects the minimum value of
SCTP_DEFAULT_MINSEGMENT and that it is correctly aligned.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b7ed879425 ]
A KASAN:use-after-free bug was found related to ip6-erspan
while running selftests/net/ip6_gre_headroom.sh
It happens because of following sequence:
- ipv6hdr pointer is obtained from skb
- skb_cow_head() is called, skb->head memory is reallocated
- old data is accessed using ipv6hdr pointer
skb_cow_head() call was added in e41c7c68ea ("ip6erspan: make sure
enough headroom at xmit."), but looking at the history there was a
chance of similar bug because gre_handle_offloads() and pskb_trim()
can also reallocate skb->head memory. Fixes tag points to commit
which introduced possibility of this bug.
This patch moves ipv6hdr pointer assignment after skb_cow_head() call.
Fixes: 5a963eb61b ("ip6_gre: Add ERSPAN native tunnel support")
Signed-off-by: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp>
Reviewed-by: Greg Rose <gvrose8192@gmail.com>
Acked-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 38cd58ed9c ]
This adds the USB id of LTE modem Quectel EG91. It requires the
same quirk as other Quectel modems to make it work.
Signed-off-by: Matevz Vucnik <vucnikm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9ba8376ce1 ]
It seems that a *break* is missing in order to avoid falling through
to the default case. Otherwise, checking *chan* makes no sense.
Fixes: 72df7a7244 ("ptp: Allow reassigning calibration pin function")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit df8ed346d4 ]
Currently also the pause flags are removed from phydev->supported because
they're not included in PHY_DEFAULT_FEATURES. I don't think this is
intended, especially when considering that this function can be called
via phy_set_max_speed() anywhere in a driver. Change the masking to mask
out only the values we're going to change. In addition remove the
misleading comment, job of this small function is just to adjust the
supported and advertised speeds.
Fixes: f3a6bd393c ("phylib: Add phy_set_max_speed helper")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b5d2d75e07 ]
Eric reported that reverting the patch that fixed and simplified IPv6
multipath routes means reverting back to invalid userspace notifications.
eg.,
$ ip -6 route add 2001:db8:1::/64 nexthop dev eth0 nexthop dev eth1
only generates a single notification:
2001:db8:1::/64 dev eth0 metric 1024 pref medium
While working on a fix for this problem I found another case that is just
broken completely - a multipath route with a gateway followed by device
followed by gateway:
$ ip -6 ro add 2001:db8:103::/64
nexthop via 2001:db8:1::64
nexthop dev dummy2
nexthop via 2001:db8:3::64
In this case the device only route is dropped completely - no notification
to userpsace but no addition to the FIB either:
$ ip -6 ro ls
2001:db8:1::/64 dev dummy1 proto kernel metric 256 pref medium
2001:db8:2::/64 dev dummy2 proto kernel metric 256 pref medium
2001:db8:3::/64 dev dummy3 proto kernel metric 256 pref medium
2001:db8:103::/64 metric 1024
nexthop via 2001:db8:1::64 dev dummy1 weight 1
nexthop via 2001:db8:3::64 dev dummy3 weight 1 pref medium
fe80::/64 dev dummy1 proto kernel metric 256 pref medium
fe80::/64 dev dummy2 proto kernel metric 256 pref medium
fe80::/64 dev dummy3 proto kernel metric 256 pref medium
Really, IPv6 multipath is just FUBAR'ed beyond repair when it comes to
device only routes, so do not allow it all.
This change will break any scripts relying on the mpath api for insert,
but I don't see any other way to handle the permutations. Besides, since
the routes are added to the FIB as standalone (non-multipath) routes the
kernel is not doing what the user requested, so it might as well tell the
user that.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e7372197e1 ]
Xin reported that icmp replies may not use the address on the device the
echo request is received if the destination address is broadcast. Instead
a route lookup is done without considering VRF context. Fix by setting
oif in flow struct to the master device if it is enslaved. That directs
the lookup to the VRF table. If the device is not enslaved, oif is still
0 so no affect.
Fixes: cd2fbe1b6b ("net: Use VRF device index for lookups on RX")
Reported-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e78bfb0751 ]
Commit 8b7008620b ("net: Don't copy pfmemalloc flag in
__copy_skb_header()") introduced a different handling for the
pfmemalloc flag in copy and clone paths.
In __skb_clone(), now, the flag is set only if it was set in the
original skb, but not cleared if it wasn't. This is wrong and
might lead to socket buffers being flagged with pfmemalloc even
if the skb data wasn't allocated from pfmemalloc reserves. Copy
the flag instead of ORing it.
Reported-by: Sabrina Dubroca <sd@queasysnail.net>
Fixes: 8b7008620b ("net: Don't copy pfmemalloc flag in __copy_skb_header()")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Tested-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8b7008620b ]
The pfmemalloc flag indicates that the skb was allocated from
the PFMEMALLOC reserves, and the flag is currently copied on skb
copy and clone.
However, an skb copied from an skb flagged with pfmemalloc
wasn't necessarily allocated from PFMEMALLOC reserves, and on
the other hand an skb allocated that way might be copied from an
skb that wasn't.
So we should not copy the flag on skb copy, and rather decide
whether to allow an skb to be associated with sockets unrelated
to page reclaim depending only on how it was allocated.
Move the pfmemalloc flag before headers_start[0] using an
existing 1-bit hole, so that __copy_skb_header() doesn't copy
it.
When cloning, we'll now take care of this flag explicitly,
contravening to the warning comment of __skb_clone().
While at it, restore the newline usage introduced by commit
b193722731 ("net: reorganize sk_buff for faster
__copy_skb_header()") to visually separate bytes used in
bitfields after headers_start[0], that was gone after commit
a9e419dc7b ("netfilter: merge ctinfo into nfct pointer storage
area"), and describe the pfmemalloc flag in the kernel-doc
structure comment.
This doesn't change the size of sk_buff or cacheline boundaries,
but consolidates the 15 bits hole before tc_index into a 2 bytes
hole before csum, that could now be filled more easily.
Reported-by: Patrick Talbert <ptalbert@redhat.com>
Fixes: c93bdd0e03 ("netvm: allow skb allocation to use PFMEMALLOC reserves")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit acc2cf4e37 ]
When tcp_diag_destroy closes a TCP_NEW_SYN_RECV socket, it first
frees it by calling inet_csk_reqsk_queue_drop_and_and_put in
tcp_abort, and then frees it again by calling sock_gen_put.
Since tcp_abort only has one caller, and all the other codepaths
in tcp_abort don't free the socket, just remove the free in that
function.
Cc: David Ahern <dsa@cumulusnetworks.com>
Tested: passes Android sock_diag_test.py, which exercises this codepath
Fixes: d7226c7a4d ("net: diag: Fix refcnt leak in error path destroying socket")
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsa@cumulusnetworks.com>
Tested-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 107d01f5ba ]
rhashtable_init() currently does not take into account the user-passed
min_size parameter unless param->nelem_hint is set as well. As such,
the default size (number of buckets) will always be HASH_DEFAULT_SIZE
even if the smallest allowed size is larger than that. Remediate this
by unconditionally calling into rounded_hashtable_size() and handling
things accordingly.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 83ed7d1fe2 ]
My randconfig builds came across an old missing dependency for ILA:
ERROR: "dst_cache_set_ip6" [net/ipv6/ila/ila.ko] undefined!
ERROR: "dst_cache_get" [net/ipv6/ila/ila.ko] undefined!
ERROR: "dst_cache_init" [net/ipv6/ila/ila.ko] undefined!
ERROR: "dst_cache_destroy" [net/ipv6/ila/ila.ko] undefined!
We almost never run into this by accident because randconfig builds
end up selecting DST_CACHE from some other tunnel protocol, and this
one appears to be the only one missing the explicit 'select'.
>From all I can tell, this problem first appeared in linux-4.9
when dst_cache support got added to ILA.
Fixes: 79ff2fc31e ("ila: Cache a route to translated address")
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 169dc027fb ]
The rol32 call is currently rotating hash but the rol'd value is
being discarded. I believe the current code is incorrect and hash
should be assigned the rotated value returned from rol32.
Thanks to David Lebrun for spotting this.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 70ba5b6db9 ]
The low and high values of the net.ipv4.ping_group_range sysctl were
being silently forced to the default disabled state when a write to the
sysctl contained GIDs that didn't map to the associated user namespace.
Confusingly, the sysctl's write operation would return success and then
a subsequent read of the sysctl would indicate that the low and high
values are the overflowgid.
This patch changes the behavior by clearly returning an error when the
sysctl write operation receives a GID range that doesn't map to the
associated user namespace. In such a situation, the previous value of
the sysctl is preserved and that range will be returned in a subsequent
read of the sysctl.
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d5a672ac9f ]
The gen_stats facility will add a header for the toplevel nlattr of type
TCA_STATS2 that contains all stats added by qdisc callbacks. A reference
to this header is stored in the gnet_dump struct, and when all the
per-qdisc callbacks have finished adding their stats, the length of the
containing header will be adjusted to the right value.
However, on architectures that need padding (i.e., that don't set
CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS), the padding nlattr is added
before the stats, which means that the stored pointer will point to the
padding, and so when the header is fixed up, the result is just a very
big padding nlattr. Because most qdiscs also supply the legacy TCA_STATS
struct, this problem has been mostly invisible, but we exposed it with
the netlink attribute-based statistics in CAKE.
Fix the issue by fixing up the stored pointer if it points to a padding
nlattr.
Tested-by: Pete Heist <pete@heistp.net>
Tested-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 37afe55b4a upstream.
When MST and atomic were introduced to nouveau, another structure that
could contain a drm_connector embedded within it was introduced; struct
nv50_mstc. This meant that we no longer would be able to simply loop
through our connector list and assume that nouveau_connector() would
return a proper pointer for each connector, since the assertion that
all connectors coming from nouveau have a full nouveau_connector struct
became invalid.
Unfortunately, none of the actual code that looped through connectors
ever got updated, which means that we've been causing invalid memory
accesses for quite a while now.
An example that was caught by KASAN:
[ 201.038698] ==================================================================
[ 201.038792] BUG: KASAN: slab-out-of-bounds in nvif_notify_get+0x190/0x1a0 [nouveau]
[ 201.038797] Read of size 4 at addr ffff88076738c650 by task kworker/0:3/718
[ 201.038800]
[ 201.038822] CPU: 0 PID: 718 Comm: kworker/0:3 Tainted: G O 4.18.0-rc4Lyude-Test+ #1
[ 201.038825] Hardware name: LENOVO 20EQS64N0B/20EQS64N0B, BIOS N1EET78W (1.51 ) 05/18/2018
[ 201.038882] Workqueue: events nouveau_display_hpd_work [nouveau]
[ 201.038887] Call Trace:
[ 201.038894] dump_stack+0xa4/0xfd
[ 201.038900] print_address_description+0x71/0x239
[ 201.038929] ? nvif_notify_get+0x190/0x1a0 [nouveau]
[ 201.038935] kasan_report.cold.6+0x242/0x2fe
[ 201.038942] __asan_report_load4_noabort+0x19/0x20
[ 201.038970] nvif_notify_get+0x190/0x1a0 [nouveau]
[ 201.038998] ? nvif_notify_put+0x1f0/0x1f0 [nouveau]
[ 201.039003] ? kmsg_dump_rewind_nolock+0xe4/0xe4
[ 201.039049] nouveau_display_init.cold.12+0x34/0x39 [nouveau]
[ 201.039089] ? nouveau_user_framebuffer_create+0x120/0x120 [nouveau]
[ 201.039133] nouveau_display_resume+0x5c0/0x810 [nouveau]
[ 201.039173] ? nvkm_client_ioctl+0x20/0x20 [nouveau]
[ 201.039215] nouveau_do_resume+0x19f/0x570 [nouveau]
[ 201.039256] nouveau_pmops_runtime_resume+0xd8/0x2a0 [nouveau]
[ 201.039264] pci_pm_runtime_resume+0x130/0x250
[ 201.039269] ? pci_restore_standard_config+0x70/0x70
[ 201.039275] __rpm_callback+0x1f2/0x5d0
[ 201.039279] ? rpm_resume+0x560/0x18a0
[ 201.039283] ? pci_restore_standard_config+0x70/0x70
[ 201.039287] ? pci_restore_standard_config+0x70/0x70
[ 201.039291] ? pci_restore_standard_config+0x70/0x70
[ 201.039296] rpm_callback+0x175/0x210
[ 201.039300] ? pci_restore_standard_config+0x70/0x70
[ 201.039305] rpm_resume+0xcc3/0x18a0
[ 201.039312] ? rpm_callback+0x210/0x210
[ 201.039317] ? __pm_runtime_resume+0x9e/0x100
[ 201.039322] ? kasan_check_write+0x14/0x20
[ 201.039326] ? do_raw_spin_lock+0xc2/0x1c0
[ 201.039333] __pm_runtime_resume+0xac/0x100
[ 201.039374] nouveau_display_hpd_work+0x67/0x1f0 [nouveau]
[ 201.039380] process_one_work+0x7a0/0x14d0
[ 201.039388] ? cancel_delayed_work_sync+0x20/0x20
[ 201.039392] ? lock_acquire+0x113/0x310
[ 201.039398] ? kasan_check_write+0x14/0x20
[ 201.039402] ? do_raw_spin_lock+0xc2/0x1c0
[ 201.039409] worker_thread+0x86/0xb50
[ 201.039418] kthread+0x2e9/0x3a0
[ 201.039422] ? process_one_work+0x14d0/0x14d0
[ 201.039426] ? kthread_create_worker_on_cpu+0xc0/0xc0
[ 201.039431] ret_from_fork+0x3a/0x50
[ 201.039441]
[ 201.039444] Allocated by task 79:
[ 201.039449] save_stack+0x43/0xd0
[ 201.039452] kasan_kmalloc+0xc4/0xe0
[ 201.039456] kmem_cache_alloc_trace+0x10a/0x260
[ 201.039494] nv50_mstm_add_connector+0x9a/0x340 [nouveau]
[ 201.039504] drm_dp_add_port+0xff5/0x1fc0 [drm_kms_helper]
[ 201.039511] drm_dp_send_link_address+0x4a7/0x740 [drm_kms_helper]
[ 201.039518] drm_dp_check_and_send_link_address+0x1a7/0x210 [drm_kms_helper]
[ 201.039525] drm_dp_mst_link_probe_work+0x71/0xb0 [drm_kms_helper]
[ 201.039529] process_one_work+0x7a0/0x14d0
[ 201.039533] worker_thread+0x86/0xb50
[ 201.039537] kthread+0x2e9/0x3a0
[ 201.039541] ret_from_fork+0x3a/0x50
[ 201.039543]
[ 201.039546] Freed by task 0:
[ 201.039549] (stack is not available)
[ 201.039551]
[ 201.039555] The buggy address belongs to the object at ffff88076738c1a8
which belongs to the cache kmalloc-2048 of size 2048
[ 201.039559] The buggy address is located 1192 bytes inside of
2048-byte region [ffff88076738c1a8, ffff88076738c9a8)
[ 201.039563] The buggy address belongs to the page:
[ 201.039567] page:ffffea001d9ce200 count:1 mapcount:0 mapping:ffff88084000d0c0 index:0x0 compound_mapcount: 0
[ 201.039573] flags: 0x8000000000008100(slab|head)
[ 201.039578] raw: 8000000000008100 ffffea001da3be08 ffffea001da25a08 ffff88084000d0c0
[ 201.039582] raw: 0000000000000000 00000000000d000d 00000001ffffffff 0000000000000000
[ 201.039585] page dumped because: kasan: bad access detected
[ 201.039588]
[ 201.039591] Memory state around the buggy address:
[ 201.039594] ffff88076738c500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 201.039598] ffff88076738c580: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 201.039601] >ffff88076738c600: 00 00 00 00 00 00 00 00 00 00 fc fc fc fc fc fc
[ 201.039604] ^
[ 201.039607] ffff88076738c680: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 201.039611] ffff88076738c700: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 201.039613] ==================================================================
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: stable@vger.kernel.org
Cc: Karol Herbst <karolherbst@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 22b76bbe08 upstream.
Every codepath in nouveau that loops through the connector list
currently does so using the old method, which is prone to race
conditions from MST connectors being created and destroyed. This has
been causing a multitude of problems, including memory corruption from
trying to access connectors that have already been freed!
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: stable@vger.kernel.org
Cc: Karol Herbst <karolherbst@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 68fe23a626 upstream.
This both uses the legacy modesetting structures in a racy manner, and
additionally also doesn't even check the right variable (enabled != the
CRTC is actually turned on for atomic).
This fixes issues on my P50 regarding the dedicated GPU not entering
runtime suspend.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5292221d6d upstream.
This reverts commit 018d82e5f0.
This breaks DDC in certain cases. Revert for 4.18 and previous kernels.
For 4.19, this is fixed with the following more extensive patches:
drm/amd/display: Serialize is_dp_sink_present
drm/amd/display: Break out function to simply read aux reply
drm/amd/display: Return aux replies directly to DRM
drm/amd/display: Right shift AUX reply value sooner than later
drm/amd/display: Read AUX channel even if only status byte is returned
Link: https://lists.freedesktop.org/archives/amd-gfx/2018-July/023788.html
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b03897cf31 upstream.
On 64-bit servers, SPRN_SPRG3 and its userspace read-only mirror
SPRN_USPRG3 are used as userspace VDSO write and read registers
respectively.
SPRN_SPRG3 is lost when we enter stop4 and above, and is currently not
restored. As a result, any read from SPRN_USPRG3 returns zero on an
exit from stop4 (Power9 only) and above.
Thus in this situation, on POWER9, any call from sched_getcpu() always
returns zero, as on powerpc, we call __kernel_getcpu() which relies
upon SPRN_USPRG3 to report the CPU and NUMA node information.
Fix this by restoring SPRN_SPRG3 on wake up from a deep stop state
with the sprg_vdso value that is cached in PACA.
Fixes: e1c1cfed54 ("powerpc/powernv: Save/Restore additional SPRs for stop4 cpuidle")
Cc: stable@vger.kernel.org # v4.14+
Reported-by: Florian Weimer <fweimer@redhat.com>
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Reviewed-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9fb8d5dc4b upstream.
When cpu_stop_queue_two_works() begins to wake the stopper threads, it does
so without preemption disabled, which leads to the following race
condition:
The source CPU calls cpu_stop_queue_two_works(), with cpu1 as the source
CPU, and cpu2 as the destination CPU. When adding the stopper threads to
the wake queue used in this function, the source CPU stopper thread is
added first, and the destination CPU stopper thread is added last.
When wake_up_q() is invoked to wake the stopper threads, the threads are
woken up in the order that they are queued in, so the source CPU's stopper
thread is woken up first, and it preempts the thread running on the source
CPU.
The stopper thread will then execute on the source CPU, disable preemption,
and begin executing multi_cpu_stop(), and wait for an ack from the
destination CPU's stopper thread, with preemption still disabled. Since the
worker thread that woke up the stopper thread on the source CPU is affine
to the source CPU, and preemption is disabled on the source CPU, that
thread will never run to dequeue the destination CPU's stopper thread from
the wake queue, and thus, the destination CPU's stopper thread will never
run, causing the source CPU's stopper thread to wait forever, and stall.
Disable preemption when waking the stopper threads in
cpu_stop_queue_two_works().
Fixes: 0b26351b91 ("stop_machine, sched: Fix migrate_swap() vs. active_balance() deadlock")
Co-Developed-by: Prasad Sodagudi <psodagud@codeaurora.org>
Signed-off-by: Prasad Sodagudi <psodagud@codeaurora.org>
Co-Developed-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Isaac J. Manjarres <isaacm@codeaurora.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: peterz@infradead.org
Cc: matt@codeblueprint.co.uk
Cc: bigeasy@linutronix.de
Cc: gregkh@linuxfoundation.org
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1530655334-4601-1-git-send-email-isaacm@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0e714d2778 upstream.
info.index can be indirectly controlled by user-space, hence leading
to a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/vfio/pci/vfio_pci.c:734 vfio_pci_ioctl()
warn: potential spectre issue 'vdev->region'
Fix this by sanitizing info.index before indirectly using it to index
vdev->region
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 95d6c0857e upstream.
Currently, intel_pstate doesn't register if _PSS is not present on
HP Proliant systems, because it expects the firmware to take over
CPU performance scaling in that case. However, if ACPI PCCH is
present, the firmware expects the kernel to use it for CPU
performance scaling and the pcc-cpufreq driver is loaded for that.
Unfortunately, the firmware interface used by that driver is not
scalable for fundamental reasons, so pcc-cpufreq is way suboptimal
on systems with more than just a few CPUs. In fact, it is better to
avoid using it at all.
For this reason, modify intel_pstate to look for ACPI PCCH if _PSS
is not present and register if it is there. Also prevent the
pcc-cpufreq driver from trying to initialize itself if intel_pstate
has been registered already.
Fixes: fbbcdc0744 (intel_pstate: skip the driver if ACPI has power mgmt option)
Reported-by: Andreas Herrmann <aherrmann@suse.com>
Reviewed-by: Andreas Herrmann <aherrmann@suse.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Tested-by: Andreas Herrmann <aherrmann@suse.com>
Cc: 4.16+ <stable@vger.kernel.org> # 4.16+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9f15bde671 upstream.
It was reported that a kernel crash happened in mem_cgroup_iter(), which
can be triggered if the legacy cgroup-v1 non-hierarchical mode is used.
Unable to handle kernel paging request at virtual address 6b6b6b6b6b6b8f
......
Call trace:
mem_cgroup_iter+0x2e0/0x6d4
shrink_zone+0x8c/0x324
balance_pgdat+0x450/0x640
kswapd+0x130/0x4b8
kthread+0xe8/0xfc
ret_from_fork+0x10/0x20
mem_cgroup_iter():
......
if (css_tryget(css)) <-- crash here
break;
......
The crashing reason is that mem_cgroup_iter() uses the memcg object whose
pointer is stored in iter->position, which has been freed before and
filled with POISON_FREE(0x6b).
And the root cause of the use-after-free issue is that
invalidate_reclaim_iterators() fails to reset the value of iter->position
to NULL when the css of the memcg is released in non- hierarchical mode.
Link: http://lkml.kernel.org/r/1531994807-25639-1-git-send-email-jing.xia@unisoc.com
Fixes: 6df38689e0 ("mm: memcontrol: fix possible memcg leak due to interrupted reclaim")
Signed-off-by: Jing Xia <jing.xia.mail@gmail.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: <chunyan.zhang@unisoc.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 93312b6da4 upstream.
mprotect(EXEC) was failing for stack mappings as default vm flags was
missing MAYEXEC.
This was triggered by glibc test suite nptl/tst-execstack testcase
What is surprising is that despite running LTP for years on, we didn't
catch this issue as it lacks a directed test case.
gcc dejagnu tests with nested functions also requiring exec stack work
fine though because they rely on the GNU_STACK segment spit out by
compiler and handled in kernel elf loader.
This glibc case is different as the stack is non exec to begin with and
a dlopen of shared lib with GNU_STACK segment triggers the exec stack
proceedings using a mprotect(PROT_EXEC) which was broken.
CC: stable@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 64234961c1 upstream.
We used to have pre-set CONFIG_INITRAMFS_SOURCE with local path
to intramfs in ARC defconfigs. This was quite convenient for
in-house development but not that convenient for newcomers
who obviusly don't have folders like "arc_initramfs" next to
the Linux source tree. Which leads to quite surprising failure
of defconfig building:
------------------------------->8-----------------------------
../scripts/gen_initramfs_list.sh: Cannot open '../../arc_initramfs_hs/'
../usr/Makefile:57: recipe for target 'usr/initramfs_data.cpio.gz' failed
make[2]: *** [usr/initramfs_data.cpio.gz] Error 1
------------------------------->8-----------------------------
So now when more and more people start to deal with our defconfigs
let's make their life easier with removal of CONFIG_INITRAMFS_SOURCE.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e3761145a upstream.
swap was broken on ARC due to silly copy-paste issue.
We encode offset from swapcache page in __swp_entry() as (off << 13) but
were not decoding back in __swp_offset() as (off >> 13) - it was still
(off << 13).
This finally fixes swap usage on ARC.
| # mkswap /dev/sda2
|
| # swapon -a -e /dev/sda2
| Adding 500728k swap on /dev/sda2. Priority:-2 extents:1 across:500728k
|
| # free
| total used free shared buffers cached
| Mem: 765104 13456 751648 4736 8 4736
| -/+ buffers/cache: 8712 756392
| Swap: 500728 0 500728
Cc: stable@vger.kernel.org
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit af1fc5baa7 upstream.
This manifsted as strace segfaulting on HSDK because gcc was targetting
the accumulator registers as GPRs, which kernek was not saving/restoring
by default.
Cc: stable@vger.kernel.org #4.14+
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c991e408d upstream.
Markus reported that BTS is sporadically missing the tail of the trace
in the perf_event data buffer: [decode error (1): instruction overflow]
shown in GDB; and bisected it to the conversion of debug_store to PTI.
A little "optimization" crept into alloc_bts_buffer(), which mistakenly
placed bts_interrupt_threshold away from the 24-byte record boundary.
Intel SDM Vol 3B 17.4.9 says "This address must point to an offset from
the BTS buffer base that is a multiple of the BTS record size."
Revert "max" from a byte count to a record count, to calculate the
bts_interrupt_threshold correctly: which turns out to fix problem seen.
Fixes: c1961a4631 ("x86/events/intel/ds: Map debug buffers in cpu_entry_area")
Reported-and-tested-by: Markus T Metzger <markus.t.metzger@intel.com>
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@intel.com>
Cc: Andi Kleen <andi.kleen@intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: stable@vger.kernel.org # v4.14+
Link: https://lkml.kernel.org/r/alpine.LSU.2.11.1807141248290.1614@eggly.anvils
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 94ffba4846 upstream.
pvti_cpu0_va is the address of shared kvmclock data structure.
pvti_cpu0_va is currently kept unset (1) on 32 bit systems, (2) when
kvmclock vsyscall is disabled, and (3) if kvmclock is not stable.
This poses a problem, because kvm_ptp needs pvti_cpu0_va, but (1) can
work on 32 bit, (2) has little relation to the vsyscall, and (3) does
not need stable kvmclock (although kvmclock won't be used for system
clock if it's not stable, so kvm_ptp is pointless in that case).
Expose pvti_cpu0_va whenever kvmclock is enabled to allow all users to
work with it.
This fixes a regression found on Gentoo: https://bugs.gentoo.org/658544.
Fixes: 9f08890ab9 ("x86/pvclock: add setter for pvclock_pvti_cpu0_va")
Cc: stable@vger.kernel.org
Reported-by: Andreas Steinmetz <ast@domdv.de>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b062b794c7 upstream.
When we switched from doing rdmsr() to reading FS/GS base values from
current->thread we completely forgot about legacy 32-bit userspaces which
we still support in KVM (why?). task->thread.{fsbase,gsbase} are only
synced for 64-bit processes, calling save_fsgs_for_kvm() and using
its result from current is illegal for legacy processes.
There's no ARCH_SET_FS/GS prctls for legacy applications. Base MSRs are,
however, not always equal to zero. Intel's manual says (3.4.4 Segment
Loading Instructions in IA-32e Mode):
"In order to set up compatibility mode for an application, segment-load
instructions (MOV to Sreg, POP Sreg) work normally in 64-bit mode. An
entry is read from the system descriptor table (GDT or LDT) and is loaded
in the hidden portion of the segment register.
...
The hidden descriptor register fields for FS.base and GS.base are
physically mapped to MSRs in order to load all address bits supported by
a 64-bit implementation.
"
The issue was found by strace test suite where 32-bit ioctl_kvm_run test
started segfaulting.
Reported-by: Dmitry V. Levin <ldv@altlinux.org>
Bisected-by: Masatake YAMATO <yamato@redhat.com>
Fixes: 42b933b597 ("x86/kvm/vmx: read MSR_{FS,KERNEL_GS}_BASE from current->thread")
Cc: stable@vger.kernel.org
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2307af1c4b upstream.
When eVMCS is enabled, all VMCS allocated to be used by KVM are marked
with revision_id of KVM_EVMCS_VERSION instead of revision_id reported
by MSR_IA32_VMX_BASIC.
However, even though not explictly documented by TLFS, VMXArea passed
as VMXON argument should still be marked with revision_id reported by
physical CPU.
This issue was found by the following setup:
* L0 = KVM which expose eVMCS to it's L1 guest.
* L1 = KVM which consume eVMCS reported by L0.
This setup caused the following to occur:
1) L1 execute hardware_enable().
2) hardware_enable() calls kvm_cpu_vmxon() to execute VMXON.
3) L0 intercept L1 VMXON and execute handle_vmon() which notes
vmxarea->revision_id != VMCS12_REVISION and therefore fails with
nested_vmx_failInvalid() which sets RFLAGS.CF.
4) L1 kvm_cpu_vmxon() don't check RFLAGS.CF for failure and therefore
hardware_enable() continues as usual.
5) L1 hardware_enable() then calls ept_sync_global() which executes
INVEPT.
6) L0 intercept INVEPT and execute handle_invept() which notes
!vmx->nested.vmxon and thus raise a #UD to L1.
7) Raised #UD caused L1 to panic.
Reviewed-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Cc: stable@vger.kernel.org
Fixes: 773e8a0425
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9432a31757 upstream.
A comment warning against this bug is there, but the code is not doing what
the comment says. Therefore it is possible that an EPOLLHUP races against
irq_bypass_register_consumer. The EPOLLHUP handler schedules irqfd_shutdown,
and if that runs soon enough, you get a use-after-free.
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5020a8e6b upstream.
Syzbot reports crashes in kvm_irqfd_assign(), caused by use-after-free
when kvm_irqfd_assign() and kvm_irqfd_deassign() run in parallel
for one specific eventfd. When the assign path hasn't finished but irqfd
has been added to kvm->irqfds.items list, another thead may deassign the
eventfd and free struct kvm_kernel_irqfd(). The assign path then uses
the struct kvm_kernel_irqfd that has been freed by deassign path. To avoid
such issue, keep irqfd under kvm->irq_srcu protection after the irqfd
has been added to kvm->irqfds.items list, and call synchronize_srcu()
in irq_shutdown() to make sure that irqfd has been fully initialized in
the assign path.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Tianyu Lan <tianyu.lan@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5f3bc39a0 upstream.
GPNFT command allocates 2 buffer for switch query. On completion, the same
buffers were freed using different size, instead of using original size at
the time of allocation.
This patch saves the size of the request and response buffers and uses that
to free them.
Following stack trace can be seen when using debug kernel
dump_stack+0x19/0x1b
__warn+0xd8/0x100
warn_slowpath_fmt+0x5f/0x80
check_unmap+0xfb/0xa20
debug_dma_free_coherent+0x110/0x160
qla24xx_sp_unmap+0x131/0x1e0 [qla2xxx]
qla24xx_async_gnnft_done+0xb6/0x550 [qla2xxx]
qla2x00_do_work+0x1ec/0x9f0 [qla2xxx]
Cc: <stable@vger.kernel.org> # v4.17+
Fixes: 33b28357dd ("scsi: qla2xxx: Fix Async GPN_FT for FCP and FC-NVMe scan")
Reported-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f13cff6c25 upstream.
Fix the description of sd_zbc_check_zone_size() to correctly explain that
the returned value is a number of device blocks, not bytes. Additionally,
the 32 bits "ret" variable used in this function may truncate the 64 bits
zone_blocks variable value upon return. To fix this, change "ret" type to
s64.
Fixes: ccce20fc79 ("sd_zbc: Avoid that resetting a zone fails sporadically")
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Cc: stable@kernel.org
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 85782e037f upstream.
Partially undo commit 9facc33687 ("bpf: reject any prog that failed
read-only lock") since it caused a regression, that is, syzkaller was
able to manage to cause a panic via fault injection deep in set_memory_ro()
path by letting an allocation fail: In x86's __change_page_attr_set_clr()
it was able to change the attributes of the primary mapping but not in
the alias mapping via cpa_process_alias(), so the second, inner call
to the __change_page_attr() via __change_page_attr_set_clr() had to split
a larger page and failed in the alloc_pages() with the artifically triggered
allocation error which is then propagated down to the call site.
Thus, for set_memory_ro() this means that it returned with an error, but
from debugging a probe_kernel_write() revealed EFAULT on that memory since
the primary mapping succeeded to get changed. Therefore the subsequent
hdr->locked = 0 reset triggered the panic as it was performed on read-only
memory, so call-site assumptions were infact wrong to assume that it would
either succeed /or/ not succeed at all since there's no such rollback in
set_memory_*() calls from partial change of mappings, in other words, we're
left in a state that is "half done". A later undo via set_memory_rw() is
succeeding though due to matching permissions on that part (aka due to the
try_preserve_large_page() succeeding). While reproducing locally with
explicitly triggering this error, the initial splitting only happens on
rare occasions and in real world it would additionally need oom conditions,
but that said, it could partially fail. Therefore, it is definitely wrong
to bail out on set_memory_ro() error and reject the program with the
set_memory_*() semantics we have today. Shouldn't have gone the extra mile
since no other user in tree today infact checks for any set_memory_*()
errors, e.g. neither module_enable_ro() / module_disable_ro() for module
RO/NX handling which is mostly default these days nor kprobes core with
alloc_insn_page() / free_insn_page() as examples that could be invoked long
after bootup and original 314beb9bca ("x86: bpf_jit_comp: secure bpf jit
against spraying attacks") did neither when it got first introduced to BPF
so "improving" with bailing out was clearly not right when set_memory_*()
cannot handle it today.
Kees suggested that if set_memory_*() can fail, we should annotate it with
__must_check, and all callers need to deal with it gracefully given those
set_memory_*() markings aren't "advisory", but they're expected to actually
do what they say. This might be an option worth to move forward in future
but would at the same time require that set_memory_*() calls from supporting
archs are guaranteed to be "atomic" in that they provide rollback if part
of the range fails, once that happened, the transition from RW -> RO could
be made more robust that way, while subsequent RO -> RW transition /must/
continue guaranteeing to always succeed the undo part.
Reported-by: syzbot+a4eb8c7766952a1ca872@syzkaller.appspotmail.com
Reported-by: syzbot+d866d1925855328eac3b@syzkaller.appspotmail.com
Fixes: 9facc33687 ("bpf: reject any prog that failed read-only lock")
Cc: Laura Abbott <labbott@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 18d405af30 upstream.
Any eBPF JIT that where its underlying arch supports ARCH_HAS_SET_MEMORY
would need to use bpf_jit_binary_{un,}lock_ro() pair instead of the
set_memory_{ro,rw}() pair directly as otherwise changes to the former
might break. arm32's eBPF conversion missed to change it, so fix this
up here.
Fixes: 39c13c204b ("arm: eBPF JIT compiler")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9262478220 upstream.
After commit 9facc33687 ("bpf: reject any prog that failed read-only lock")
offsetof(struct bpf_binary_header, image) became 3 instead of 4,
breaking powerpc BPF badly, since instructions need to be word aligned.
Fixes: 9facc33687 ("bpf: reject any prog that failed read-only lock")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b4f18c063a upstream.
In order to forward the guest's ARCH_WORKAROUND_2 calls to EL3,
add a small(-ish) sequence to handle it at EL2. Special care must
be taken to track the state of the guest itself by updating the
workaround flags. We also rely on patching to enable calls into
the firmware.
Note that since we need to execute branches, this always executes
after the Spectre-v2 mitigation has been applied.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 55e3748e89 upstream.
In order to offer ARCH_WORKAROUND_2 support to guests, we need
a bit of infrastructure.
Let's add a flag indicating whether or not the guest uses
SSBD mitigation. Depending on the state of this flag, allow
KVM to disable ARCH_WORKAROUND_2 before entering the guest,
and enable it when exiting it.
Reviewed-by: Christoffer Dall <christoffer.dall@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 85478bab40 upstream.
As we're going to require to access per-cpu variables at EL2,
let's craft the minimum set of accessors required to implement
reading a per-cpu variable, relying on tpidr_el2 to contain the
per-cpu offset.
Reviewed-by: Christoffer Dall <christoffer.dall@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9cdc0108ba upstream.
If running on a system that performs dynamic SSBD mitigation, allow
userspace to request the mitigation for itself. This is implemented
as a prctl call, allowing the mitigation to be enabled or disabled at
will for this particular thread.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9dd9614f54 upstream.
In order to allow userspace to be mitigated on demand, let's
introduce a new thread flag that prevents the mitigation from
being turned off when exiting to userspace, and doesn't turn
it on on entry into the kernel (with the assumption that the
mitigation is always enabled in the kernel itself).
This will be used by a prctl interface introduced in a later
patch.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 647d0519b5 upstream.
On a system where firmware can dynamically change the state of the
mitigation, the CPU will always come up with the mitigation enabled,
including when coming back from suspend.
If the user has requested "no mitigation" via a command line option,
let's enforce it by calling into the firmware again to disable it.
Similarily, for a resume from hibernate, the mitigation could have
been disabled by the boot kernel. Let's ensure that it is set
back on in that case.
Acked-by: Will Deacon <will.deacon@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 986372c436 upstream.
In order to avoid checking arm64_ssbd_callback_required on each
kernel entry/exit even if no mitigation is required, let's
add yet another alternative that by default jumps over the mitigation,
and that gets nop'ed out if we're doing dynamic mitigation.
Think of it as a poor man's static key...
Reviewed-by: Julien Grall <julien.grall@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a43ae4dfe5 upstream.
On a system where the firmware implements ARCH_WORKAROUND_2,
it may be useful to either permanently enable or disable the
workaround for cases where the user decides that they'd rather
not get a trap overhead, and keep the mitigation permanently
on or off instead of switching it on exception entry/exit.
In any case, default to the mitigation being enabled.
Reviewed-by: Julien Grall <julien.grall@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e2906245f upstream.
In order for the kernel to protect itself, let's call the SSBD mitigation
implemented by the higher exception level (either hypervisor or firmware)
on each transition between userspace and kernel.
We must take the PSCI conduit into account in order to target the
right exception level, hence the introduction of a runtime patching
callback.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Julien Grall <julien.grall@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eff0e9e107 upstream.
We've so far used the PSCI return codes for SMCCC because they
were extremely similar. But with the new ARM DEN 0070A specification,
"NOT_REQUIRED" (-2) is clashing with PSCI's "PSCI_RET_INVALID_PARAMS".
Let's bite the bullet and add SMCCC specific return codes. Users
can be repainted as and when required.
Acked-by: Will Deacon <will.deacon@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c7a8978432 upstream.
syzkaller managed to trigger the following bug through fault injection:
[...]
[ 141.043668] verifier bug. No program starts at insn 3
[ 141.044648] WARNING: CPU: 3 PID: 4072 at kernel/bpf/verifier.c:1613
get_callee_stack_depth kernel/bpf/verifier.c:1612 [inline]
[ 141.044648] WARNING: CPU: 3 PID: 4072 at kernel/bpf/verifier.c:1613
fixup_call_args kernel/bpf/verifier.c:5587 [inline]
[ 141.044648] WARNING: CPU: 3 PID: 4072 at kernel/bpf/verifier.c:1613
bpf_check+0x525e/0x5e60 kernel/bpf/verifier.c:5952
[ 141.047355] CPU: 3 PID: 4072 Comm: a.out Not tainted 4.18.0-rc4+ #51
[ 141.048446] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),BIOS 1.10.2-1 04/01/2014
[ 141.049877] Call Trace:
[ 141.050324] __dump_stack lib/dump_stack.c:77 [inline]
[ 141.050324] dump_stack+0x1c9/0x2b4 lib/dump_stack.c:113
[ 141.050950] ? dump_stack_print_info.cold.2+0x52/0x52 lib/dump_stack.c:60
[ 141.051837] panic+0x238/0x4e7 kernel/panic.c:184
[ 141.052386] ? add_taint.cold.5+0x16/0x16 kernel/panic.c:385
[ 141.053101] ? __warn.cold.8+0x148/0x1ba kernel/panic.c:537
[ 141.053814] ? __warn.cold.8+0x117/0x1ba kernel/panic.c:530
[ 141.054506] ? get_callee_stack_depth kernel/bpf/verifier.c:1612 [inline]
[ 141.054506] ? fixup_call_args kernel/bpf/verifier.c:5587 [inline]
[ 141.054506] ? bpf_check+0x525e/0x5e60 kernel/bpf/verifier.c:5952
[ 141.055163] __warn.cold.8+0x163/0x1ba kernel/panic.c:538
[ 141.055820] ? get_callee_stack_depth kernel/bpf/verifier.c:1612 [inline]
[ 141.055820] ? fixup_call_args kernel/bpf/verifier.c:5587 [inline]
[ 141.055820] ? bpf_check+0x525e/0x5e60 kernel/bpf/verifier.c:5952
[...]
What happens in jit_subprogs() is that kcalloc() for the subprog func
buffer is failing with NULL where we then bail out. Latter is a plain
return -ENOMEM, and this is definitely not okay since earlier in the
loop we are walking all subprogs and temporarily rewrite insn->off to
remember the subprog id as well as insn->imm to temporarily point the
call to __bpf_call_base + 1 for the initial JIT pass. Thus, bailing
out in such state and handing this over to the interpreter is troublesome
since later/subsequent e.g. find_subprog() lookups are based on wrong
insn->imm.
Therefore, once we hit this point, we need to jump to out_free path
where we undo all changes from earlier loop, so that interpreter can
work on unmodified insn->{off,imm}.
Another point is that should find_subprog() fail in jit_subprogs() due
to a verifier bug, then we also should not simply defer the program to
the interpreter since also here we did partial modifications. Instead
we should just bail out entirely and return an error to the user who is
trying to load the program.
Fixes: 1c2a088a66 ("bpf: x64: add JIT support for multi-function programs")
Reported-by: syzbot+7d427828b2ea6e592804@syzkaller.appspotmail.com
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9901c5d77e upstream.
This fixes a crash where we assign tcp_prot to IPv6 sockets instead
of tcpv6_prot.
Previously we overwrote the sk->prot field with tcp_prot even in the
AF_INET6 case. This patch ensures the correct tcp_prot and tcpv6_prot
are used.
Tested with 'netserver -6' and 'netperf -H [IPv6]' as well as
'netperf -H [IPv4]'. The ESTABLISHED check resolves the previously
crashing case here.
Fixes: 174a79ff95 ("bpf: sockmap with sk redirect support")
Reported-by: syzbot+5c063698bdbfac19f363@syzkaller.appspotmail.com
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd4a4ae468 upstream.
If we end up splitting a bio and the queue goes away between
the initial submission and the later split submission, then we
can block forever in blk_queue_enter() waiting for the reference
to drop to zero. This will never happen, since we already hold
a reference.
Mark a split bio as already having entered the queue, so we can
just use the live non-blocking queue enter variant.
Thanks to Tetsuo Handa for the analysis.
Reported-by: syzbot+c4f9cebf9d651f6e54de@syzkaller.appspotmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9facc33687 upstream.
We currently lock any JITed image as read-only via bpf_jit_binary_lock_ro()
as well as the BPF image as read-only through bpf_prog_lock_ro(). In
the case any of these would fail we throw a WARN_ON_ONCE() in order to
yell loudly to the log. Perhaps, to some extend, this may be comparable
to an allocation where __GFP_NOWARN is explicitly not set.
Added via 65869a47f3 ("bpf: improve read-only handling"), this behavior
is slightly different compared to any of the other in-kernel set_memory_ro()
users who do not check the return code of set_memory_ro() and friends /at
all/ (e.g. in the case of module_enable_ro() / module_disable_ro()). Given
in BPF this is mandatory hardening step, we want to know whether there
are any issues that would leave both BPF data writable. So it happens
that syzkaller enabled fault injection and it triggered memory allocation
failure deep inside x86's change_page_attr_set_clr() which was triggered
from set_memory_ro().
Now, there are two options: i) leaving everything as is, and ii) reworking
the image locking code in order to have a final checkpoint out of the
central bpf_prog_select_runtime() which probes whether any of the calls
during prog setup weren't successful, and then bailing out with an error.
Option ii) is a better approach since this additional paranoia avoids
altogether leaving any potential W+X pages from BPF side in the system.
Therefore, lets be strict about it, and reject programs in such unlikely
occasion. While testing I noticed also that one bpf_prog_lock_ro()
call was missing on the outer dummy prog in case of calls, e.g. in the
destructor we call bpf_prog_free_deferred() on the main prog where we
try to bpf_prog_unlock_free() the program, and since we go via
bpf_prog_select_runtime() do that as well.
Reported-by: syzbot+3b889862e65a98317058@syzkaller.appspotmail.com
Reported-by: syzbot+9e762b52dd17e616a7a5@syzkaller.appspotmail.com
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ee7e8697d upstream.
syzbot is reporting NULL pointer dereference at wb_workfn() [1] due to
wb->bdi->dev being NULL. And Dmitry confirmed that wb->state was
WB_shutting_down after wb->bdi->dev became NULL. This indicates that
unregister_bdi() failed to call wb_shutdown() on one of wb objects.
The problem is in cgwb_bdi_unregister() which does cgwb_kill() and thus
drops bdi's reference to wb structures before going through the list of
wbs again and calling wb_shutdown() on each of them. This way the loop
iterating through all wbs can easily miss a wb if that wb has already
passed through cgwb_remove_from_bdi_list() called from wb_shutdown()
from cgwb_release_workfn() and as a result fully shutdown bdi although
wb_workfn() for this wb structure is still running. In fact there are
also other ways cgwb_bdi_unregister() can race with
cgwb_release_workfn() leading e.g. to use-after-free issues:
CPU1 CPU2
cgwb_bdi_unregister()
cgwb_kill(*slot);
cgwb_release()
queue_work(cgwb_release_wq, &wb->release_work);
cgwb_release_workfn()
wb = list_first_entry(&bdi->wb_list, ...)
spin_unlock_irq(&cgwb_lock);
wb_shutdown(wb);
...
kfree_rcu(wb, rcu);
wb_shutdown(wb); -> oops use-after-free
We solve these issues by synchronizing writeback structure shutdown from
cgwb_bdi_unregister() with cgwb_release_workfn() using a new mutex. That
way we also no longer need synchronization using WB_shutting_down as the
mutex provides it for CONFIG_CGROUP_WRITEBACK case and without
CONFIG_CGROUP_WRITEBACK wb_shutdown() can be called only once from
bdi_unregister().
Reported-by: syzbot <syzbot+4a7438e774b21ddd8eca@syzkaller.appspotmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 84379c9afe upstream.
Eric Dumazet reports:
Here is a reproducer of an annoying bug detected by syzkaller on our production kernel
[..]
./b78305423 enable_conntrack
Then :
sleep 60
dmesg | tail -10
[ 171.599093] unregister_netdevice: waiting for lo to become free. Usage count = 2
[ 181.631024] unregister_netdevice: waiting for lo to become free. Usage count = 2
[ 191.687076] unregister_netdevice: waiting for lo to become free. Usage count = 2
[ 201.703037] unregister_netdevice: waiting for lo to become free. Usage count = 2
[ 211.711072] unregister_netdevice: waiting for lo to become free. Usage count = 2
[ 221.959070] unregister_netdevice: waiting for lo to become free. Usage count = 2
Reproducer sends ipv6 fragment that hits nfct defrag via LOCAL_OUT hook.
skb gets queued until frag timer expiry -- 1 minute.
Normally nf_conntrack_reasm gets called during prerouting, so skb has
no dst yet which might explain why this wasn't spotted earlier.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Reported-by: John Sperbeck <jsperbeck@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Tested-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 32da12216e upstream.
In the zerocopy sendmsg() path, there are error checks to revert
the zerocopy if we get any error code. syzkaller has discovered
that tls_push_record can return -ECONNRESET, which is fatal, and
happens after the point at which it is safe to revert the iter,
as we've already passed the memory to do_tcp_sendpages.
Previously this code could return -ENOMEM and we would want to
revert the iter, but AFAIK this no longer returns ENOMEM after
a447da7d00 ("tls: fix waitall behavior in tls_sw_recvmsg"),
so we fail for all error codes.
Reported-by: syzbot+c226690f7b3126c5ee04@syzkaller.appspotmail.com
Reported-by: syzbot+709f2810a6a05f11d4d3@syzkaller.appspotmail.com
Signed-off-by: Dave Watson <davejwatson@fb.com>
Fixes: 3c4d755915 ("tls: kernel TLS support")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c604cb7670 upstream.
My recent fix for dns_resolver_preparse() printing very long strings was
incomplete, as shown by syzbot which still managed to hit the
WARN_ONCE() in set_precision() by adding a crafted "dns_resolver" key:
precision 50001 too large
WARNING: CPU: 7 PID: 864 at lib/vsprintf.c:2164 vsnprintf+0x48a/0x5a0
The bug this time isn't just a printing bug, but also a logical error
when multiple options ("#"-separated strings) are given in the key
payload. Specifically, when separating an option string into name and
value, if there is no value then the name is incorrectly considered to
end at the end of the key payload, rather than the end of the current
option. This bypasses validation of the option length, and also means
that specifying multiple options is broken -- which presumably has gone
unnoticed as there is currently only one valid option anyway.
A similar problem also applied to option values, as the kstrtoul() when
parsing the "dnserror" option will read past the end of the current
option and into the next option.
Fix these bugs by correctly computing the length of the option name and
by copying the option value, null-terminated, into a temporary buffer.
Reproducer for the WARN_ONCE() that syzbot hit:
perl -e 'print "#A#", "\0" x 50000' | keyctl padd dns_resolver desc @s
Reproducer for "dnserror" option being parsed incorrectly (expected
behavior is to fail when seeing the unknown option "foo", actual
behavior was to read the dnserror value as "1#foo" and fail there):
perl -e 'print "#dnserror=1#foo\0"' | keyctl padd dns_resolver desc @s
Reported-by: syzbot <syzkaller@googlegroups.com>
Fixes: 4a2d789267 ("DNS: If the DNS server returns an error, allow that to be cached [ver #2]")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 11ff7288be upstream.
the ebtables evaluation loop expects targets to return
positive values (jumps), or negative values (absolute verdicts).
This is completely different from what xtables does.
In xtables, targets are expected to return the standard netfilter
verdicts, i.e. NF_DROP, NF_ACCEPT, etc.
ebtables will consider these as jumps.
Therefore reject any target found due to unspec fallback.
v2: also reject watchers. ebtables ignores their return value, so
a target that assumes skb ownership (and returns NF_STOLEN) causes
use-after-free.
The only watchers in the 'ebtables' front-end are log and nflog;
both have AF_BRIDGE specific wrappers on kernel side.
Reported-by: syzbot+2b43f681169a2a0d306a@syzkaller.appspotmail.com
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 35a88a18d7 upstream.
Commit de0aa7b2f9 ("PCI: hv: Fix 2 hang issues in hv_compose_msi_msg()")
uses local_bh_disable()/enable(), because hv_pci_onchannelcallback() can
also run in tasklet context as the channel event callback, so bottom halves
should be disabled to prevent a race condition.
With CONFIG_PROVE_LOCKING=y in the recent mainline, or old kernels that
don't have commit f71b74bca6 ("irq/softirqs: Use lockdep to assert IRQs
are disabled/enabled"), when the upper layer IRQ code calls
hv_compose_msi_msg() with local IRQs disabled, we'll see a warning at the
beginning of __local_bh_enable_ip():
IRQs not enabled as expected
WARNING: CPU: 0 PID: 408 at kernel/softirq.c:162 __local_bh_enable_ip
The warning exposes an issue in de0aa7b2f9: local_bh_enable() can
potentially call do_softirq(), which is not supposed to run when local IRQs
are disabled. Let's fix this by using local_irq_save()/restore() instead.
Note: hv_pci_onchannelcallback() is not a hot path because it's only called
when the PCI device is hot added and removed, which is infrequent.
Fixes: de0aa7b2f9 ("PCI: hv: Fix 2 hang issues in hv_compose_msi_msg()")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Cc: stable@vger.kernel.org
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a98302de1 upstream.
Without this patch, firmware will not run properly on rtl8821ae, and it
causes bad user experience. For example, bad connection performance with
low rate, higher power consumption, and so on.
rtl8821ae uses two kinds of firmwares for normal and WoWlan cases, and
each firmware has firmware data buffer and size individually. Original
code always overwrite size of normal firmware rtlpriv->rtlhal.fwsize, and
this mismatch causes firmware checksum error, then firmware can't start.
In this situation, driver gives message "Firmware is not ready to run!".
Fixes: fe89707f0a ("rtlwifi: rtl8821ae: Simplify loading of WOWLAN firmware")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Cc: Stable <stable@vger.kernel.org> # 4.0+
Reviewed-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 676bcfece1 upstream.
t.qset_idx can be indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/net/ethernet/chelsio/cxgb3/cxgb3_main.c:2286 cxgb_extension_ioctl()
warn: potential spectre issue 'adapter->msix_info'
Fix this by sanitizing t.qset_idx before using it to index
adapter->msix_info
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2471c75efe ]
The driver was combining XDP_TX virtqueue_kick and XDP_REDIRECT
map flushing (xdp_do_flush_map). This is suboptimal, these two
flush operations should be kept separate.
The suboptimal behavior was introduced in commit 9267c430c6
("virtio-net: add missing virtqueue kick when flushing packets").
Fixes: 9267c430c6 ("virtio-net: add missing virtqueue kick when flushing packets")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4789a21880 ]
When qeth_l2_set_mac_address() finds the card in a non-reachable state,
it merely copies the new MAC address into dev->dev_addr so that
__qeth_l2_set_online() can later register it with the HW.
But __qeth_l2_set_online() may very well be running concurrently, so we
can't trust the card state without appropriate locking:
If the online sequence is past the point where it registers
dev->dev_addr (but not yet in SOFTSETUP state), any address change needs
to be properly programmed into the HW. Otherwise the netdevice ends up
with a different MAC address than what's set in the HW, and inbound
traffic is not forwarded as expected.
This is most likely to occur for OSD in LPAR, where
commit 21b1702af1 ("s390/qeth: improve fallback to random MAC address")
now triggers eg. systemd to immediately change the MAC when the netdevice
is registered with a NET_ADDR_RANDOM address.
Fixes: bcacfcbc82 ("s390/qeth: fix MAC address update sequence")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9d0a58fb97 ]
*ether_addr*_64bits functions have been introduced to optimize
performance critical paths, which access 6-byte ethernet address as u64
value to get "nice" assembly. A harmless hack works nicely on ethernet
addresses shoved into a structure or a larger buffer, until busted by
Kasan on smth like plain (u8 *)[6].
qeth_l2_set_mac_address calls qeth_l2_remove_mac passing
u8 old_addr[ETH_ALEN] as an argument.
Adding/removing macs for an ethernet adapter is not that performance
critical. Moreover is_multicast_ether_addr_64bits itself on s390 is not
faster than is_multicast_ether_addr:
is_multicast_ether_addr(%r2) -> %r2
llc %r2,0(%r2)
risbg %r2,%r2,63,191,0
is_multicast_ether_addr_64bits(%r2) -> %r2
llgc %r2,0(%r2)
risbg %r2,%r2,63,191,0
So, let's just use is_multicast_ether_addr instead of
is_multicast_ether_addr_64bits.
Fixes: bcacfcbc82 ("s390/qeth: fix MAC address update sequence")
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4664610537 ]
This reverts commit b7493e91c1.
On its own, querying RDEV for a MAC address works fine. But when upgrading
from a qeth that previously queried DDEV on a z/VM NIC (ie. any kernel with
commit ec61bd2fd2), the RDEV query now returns a _different_ MAC address
than the DDEV query.
If the NIC is configured with MACPROTECT, z/VM apparently requires us to
use the MAC that was initially returned (on DDEV) and registered. So after
upgrading to a kernel that uses RDEV, the SETVMAC registration cmd for the
new MAC address fails and we end up with a non-operabel interface.
To avoid regressions on upgrade, switch back to using DDEV for the MAC
address query. The downgrade path (first RDEV, later DDEV) is fine, in this
case both queries return the same MAC address.
Fixes: b7493e91c1 ("s390/qeth: use Read device to query hypervisor for MAC")
Reported-by: Michal Kubecek <mkubecek@suse.com>
Tested-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit aff2252a2a ]
In smartnic env, the host (PF) driver might not be an e-switch
manager, hence the switchdev mode representors are running on
the embedded cpu (EC) and not at the host.
As such, we should avoid dealing with vport representors if
not being esw manager.
Fixes: b5ca15ad7e ('IB/mlx5: Add proper representors support')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2e68931238 ]
The driver was combining the XDP_TX tail flush and XDP_REDIRECT
map flushing (xdp_do_flush_map). This is suboptimal, these two
flush operations should be kept separate.
It looks like the mistake was copy-pasted from ixgbe.
Fixes: d9314c474d ("i40e: add support for XDP_REDIRECT")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 56f772279a ]
In failure path, we overwrite err to what vnic_rq_disable() returns. In
case it returns 0, enic_open() returns success in case of error.
Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Fixes: e8588e2685 ("enic: enable rq before updating rq descriptors")
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 45c8184c1b ]
Update the features after calling register_netdev() otherwise the
device features are not set up correctly and it not possible to change
the MTU of the device. After this change, the features reported by
ethtool match the device's features before the commit which introduced
the issue and it is possible to change the device's MTU.
Fixes: f599c64fdf ("xen-netfront: Fix race between device setup and open")
Reported-by: Liam Shepherd <liam@dancer.es>
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 951a8ee6de ]
TC shared blocks allow multiple qdiscs to be grouped together and filters
shared between them. Currently the chains of filters attached to a block
are only flushed when the block is removed. If a qdisc is removed from a
block but the block still exists, flow del messages are not passed to the
callback registered for that qdisc. For the NFP, this presents the
possibility of rules still existing in hw when they should be removed.
Prevent binding to shared blocks until the kernel can send per qdisc del
messages when block unbinds occur.
tcf_block_shared() was not used outside of the core until now, so also
add an empty implementation for builds with CONFIG_NET_CLS=n.
Fixes: 4861738775 ("net: sched: introduce shared filter blocks infrastructure")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3f76df1982 ]
As noticed by Eric, we need to switch to the helper
dev_change_tx_queue_len() for SIOCSIFTXQLEN call path too,
otheriwse still miss dev_qdisc_change_tx_queue_len().
Fixes: 6a643ddb56 ("net: introduce helper dev_change_tx_queue_len()")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fec9d3b1dc ]
The macb driver currently crashes on at91rm9200 with the following trace:
Unable to handle kernel NULL pointer dereference at virtual address 00000014
[...]
[<c031da44>] (macb_rx_desc) from [<c031f2bc>] (at91ether_open+0x2e8/0x3f8)
[<c031f2bc>] (at91ether_open) from [<c041e8d8>] (__dev_open+0x120/0x13c)
[<c041e8d8>] (__dev_open) from [<c041ec08>] (__dev_change_flags+0x17c/0x1a8)
[<c041ec08>] (__dev_change_flags) from [<c041ec4c>] (dev_change_flags+0x18/0x4c)
[<c041ec4c>] (dev_change_flags) from [<c07a5f4c>] (ip_auto_config+0x220/0x10b0)
[<c07a5f4c>] (ip_auto_config) from [<c000a4fc>] (do_one_initcall+0x78/0x18c)
[<c000a4fc>] (do_one_initcall) from [<c0783e50>] (kernel_init_freeable+0x184/0x1c4)
[<c0783e50>] (kernel_init_freeable) from [<c0574d70>] (kernel_init+0x8/0xe8)
[<c0574d70>] (kernel_init) from [<c00090e0>] (ret_from_fork+0x14/0x34)
Solve that by initializing bp->queues[0].bp in at91ether_init (as is done
in macb_init).
Fixes: ae1f2a56d2 ("net: macb: Added support for many RX queues")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a64119415f ]
Previously it was not possible to distinguish between mpls ether types and
other ether types. This leads to incorrect classification of offloaded
filters that match on mpls ether type. For example the following two
filters overlap:
# tc filter add dev eth0 parent ffff: \
protocol 0x8847 flower \
action mirred egress redirect dev eth1
# tc filter add dev eth0 parent ffff: \
protocol 0x0800 flower \
action mirred egress redirect dev eth2
The driver now correctly includes the mac_mpls layer where HW stores mpls
fields, when it detects an mpls ether type. It also sets the MPLS_Q bit to
indicate that the filter should match mpls packets.
Fixes: bb055c198d ("nfp: add mpls match offloading support")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 82be2ab159 ]
Following warning is seen when rmmod hinic. This is because affinity
value is not reset before calling free_irq(). This patch fixes it.
[ 55.181232] WARNING: CPU: 38 PID: 19589 at kernel/irq/manage.c:1608
__free_irq+0x2aa/0x2c0
Fixes: 352f58b0d9 ("net-next/hinic: Set Rxq irq to specific cpu for NUMA")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e5ab564c9e ]
The dst_cid and src_cid are 64 bits, therefore 64 bit accessors should be
used, and in fact in virtio_transport_common.c only 64 bit accessors are
used. Using 32 bit accessors for 64 bit values breaks big endian systems.
This patch fixes a wrong use of le32_to_cpu in virtio_transport_send_pkt.
Fixes: b911682318 ("VSOCK: add loopback to virtio_transport")
Signed-off-by: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b8f1f65882 ]
Sock will be NULL if we pass -1 to vhost_net_set_backend(), but when
we meet errors during ubuf allocation, the code does not check for
NULL before calling sockfd_put(), this will lead NULL
dereferencing. Fixing by checking sock pointer before.
Fixes: bab632d69e ("vhost: vhost TX zero-copy support")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1236f22fba ]
If SACK is not enabled and the first cumulative ACK after the RTO
retransmission covers more than the retransmitted skb, a spurious
FRTO undo will trigger (assuming FRTO is enabled for that RTO).
The reason is that any non-retransmitted segment acknowledged will
set FLAG_ORIG_SACK_ACKED in tcp_clean_rtx_queue even if there is
no indication that it would have been delivered for real (the
scoreboard is not kept with TCPCB_SACKED_ACKED bits in the non-SACK
case so the check for that bit won't help like it does with SACK).
Having FLAG_ORIG_SACK_ACKED set results in the spurious FRTO undo
in tcp_process_loss.
We need to use more strict condition for non-SACK case and check
that none of the cumulatively ACKed segments were retransmitted
to prove that progress is due to original transmissions. Only then
keep FLAG_ORIG_SACK_ACKED set, allowing FRTO undo to proceed in
non-SACK case.
(FLAG_ORIG_SACK_ACKED is planned to be renamed to FLAG_ORIG_PROGRESS
to better indicate its purpose but to keep this change minimal, it
will be done in another patch).
Besides burstiness and congestion control violations, this problem
can result in RTO loop: When the loss recovery is prematurely
undoed, only new data will be transmitted (if available) and
the next retransmission can occur only after a new RTO which in case
of multiple losses (that are not for consecutive packets) requires
one RTO per loss to recover.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Tested-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c860e997e9 ]
Fast Open key could be stored in different endian based on the CPU.
Previously hosts in different endianness in a server farm using
the same key config (sysctl value) would produce different cookies.
This patch fixes it by always storing it as little endian to keep
same API for LE hosts.
Reported-by: Daniele Iamartino <danielei@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 977c7114eb ]
On receving an incomplete message, the existing code stores the
remaining length of the cloned skb in the early_eaten field instead of
incrementing the value returned by __strp_recv. This defers invocation
of sock_rfree for the current skb until the next invocation of
__strp_recv, which returns early_eaten if early_eaten is non-zero.
This behavior causes a stall when the current message occupies the very
tail end of a massive skb, and strp_peek/need_bytes indicates that the
remainder of the current message has yet to arrive on the socket. The
TCP receive buffer is totally full, causing the TCP window to go to
zero, so the remainder of the message will never arrive.
Incrementing the value returned by __strp_recv by the amount otherwise
stored in early_eaten prevents stalls of this nature.
Signed-off-by: Doron Roberts-Kedes <doronrk@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b6cfffa7ad ]
HW does not support Half-duplex mode in multi-queue
scenario. Fix it by not advertising the Half-Duplex
mode if multi-queue enabled.
Signed-off-by: Bhadram Varka <vbhadram@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ce28867fd2 ]
If qeth_qdio_output_handler() detects that a transmit requires async
completion, it replaces the pending buffer's metadata object
(qeth_qdio_out_buffer) so that this queue buffer can be re-used while
the data is pending completion.
Later when the CQ indicates async completion of such a metadata object,
qeth_qdio_cq_handler() tries to free any data associated with this
object (since HW has now completed the transfer). By calling
qeth_clear_output_buffer(), it erronously operates on the queue buffer
that _previously_ belonged to this transfer ... but which has been
potentially re-used several times by now.
This results in double-free's of the buffer's data, and failing
transmits as the buffer descriptor is scrubbed in mid-air.
The correct way of handling this situation is to
1. scrub the queue buffer when it is prepared for re-use, and
2. later obtain the data addresses from the async-completion notifier
(ie. the AOB), instead of the queue buffer.
All this only affects qeth devices used for af_iucv HiperTransport.
Fixes: 0da9581ddb ("qeth: exploit asynchronous delivery of storage blocks")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0ee1f47349 ]
When unplugging an r8152 adapter while the interface is UP, the NIC
becomes unusable. usb->disconnect (aka rtl8152_disconnect) deletes
napi. Then, rtl8152_disconnect calls unregister_netdev and that invokes
netdev->ndo_stop (aka rtl8152_close). rtl8152_close tries to
napi_disable, but the napi is already deleted by disconnect above. So
the first while loop in napi_disable never finishes. This results in
complete deadlock of the network layer as there is rtnl_mutex held by
unregister_netdev.
So avoid the call to napi_disable in rtl8152_close when the device is
already gone.
The other calls to usb_kill_urb, cancel_delayed_work_sync,
netif_stop_queue etc. seem to be fine. The urb and netdev is not
destroyed yet.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: linux-usb@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e7e197edd0 ]
This module exposes two USB configurations: a QMI+AT capable setup on
USB config #1 and a MBIM capable setup on USB config #2.
By default the kernel will choose the MBIM capable configuration as
long as the cdc_mbim driver is available. This patch adds support for
the QMI port in the secondary configuration.
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bb7858ba11 ]
Memory size is limited in the kdump kernel environment. Allocation of more
msix-vectors (or queues) consumes few tens of MBs of memory, which might
lead to the kdump kernel failure.
This patch adds changes to limit the number of MSI-X vectors in kdump
kernel to minimum required value (i.e., 2 per engine).
Fixes: fe56b9e6a ("qed: Add module with basic common support")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 538f8d00ba ]
By default, driver sets the eswitch mode incorrectly as VEB (virtual
Ethernet bridging).
Need to set VEB eswitch mode only when sriov is enabled, and it should be
to set NONE by default. The patch incorporates this change.
Fixes: 0fefbfbaa ("qed*: Management firmware - notifications and defaults")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 82a4e71b15 ]
When ptp clock is not available for a PF (e.g., higher PFs in NPAR mode),
get-tsinfo() callback should return the software timestamp capabilities
instead of returning the error.
Fixes: 4c55215c ("qede: Add driver support for PTP")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8c43bd1706 ]
Similar to 69678bcd4d ("udp: fix SO_BINDTODEVICE"), TCP socket lookups
need to fail if dev_match is not true. Currently, a packet to a given port
can match a socket bound to device when it should not. In the VRF case,
this causes the lookup to hit a VRF socket and not a global socket
resulting in a response trying to go through the VRF when it should not.
Fixes: 3fa6f616a7 ("net: ipv4: add second dif to inet socket lookups")
Fixes: 4297a0ef08 ("net: ipv6: add second dif to inet6 socket lookups")
Reported-by: Lou Berger <lberger@labn.net>
Diagnosed-by: Renato Westphal <renato@opensourcerouting.org>
Tested-by: Renato Westphal <renato@opensourcerouting.org>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 12b03558ce ]
After commit 88078d98d1 ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE
are friends"), sungem owners reported the infamous "eth0: hw csum failure"
message.
CHECKSUM_COMPLETE has in fact never worked for this driver, but this
was masked by the fact that upper stacks had to strip the FCS, and
therefore skb->ip_summed was set back to CHECKSUM_NONE before
my recent change.
Driver configures a number of bytes to skip when the chip computes
the checksum, and for some reason only half of the Ethernet header
was skipped.
Then a second problem is that we should strip the FCS by default,
unless the driver is updated to eventually support NETIF_F_RXFCS in
the future.
Finally, a driver should check if NETIF_F_RXCSUM feature is enabled
or not, so that the admin can turn off rx checksum if wanted.
Many thanks to Andreas Schwab and Mathieu Malaterre for their
help in debugging this issue.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Meelis Roos <mroos@linux.ee>
Reported-by: Mathieu Malaterre <malat@debian.org>
Reported-by: Andreas Schwab <schwab@linux-m68k.org>
Tested-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7e85dc8cb3 ]
When blackhole is used on top of classful qdisc like hfsc it breaks
qlen and backlog counters because packets are disappear without notice.
In HFSC non-zero qlen while all classes are inactive triggers warning:
WARNING: ... at net/sched/sch_hfsc.c:1393 hfsc_dequeue+0xba4/0xe90 [sch_hfsc]
and schedules watchdog work endlessly.
This patch return __NET_XMIT_BYPASS in addition to NET_XMIT_SUCCESS,
this flag tells upper layer: this packet is gone and isn't queued.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cbf56c2962 ]
in the following script
# tc actions add action ife encode allow prio pass index 42
# tc actions replace action ife encode allow tcindex drop index 42
the action control should remain equal to 'pass', if the kernel failed
to replace the TC action. Pospone the assignment of the action control,
to ensure it is not overwritten in the error path of tcf_ife_init().
Fixes: ef6980b6be ("introduce IFE action")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0a889b9404 ]
a recursive lock warning [1] can be observed with the following script,
# $TC actions add action ife encode allow prio pass index 42
IFE type 0xED3E
# $TC actions replace action ife encode allow tcindex pass index 42
in case the kernel was unable to run the last command (e.g. because of
the impossibility to load 'act_meta_skbtcindex'). For a similar reason,
the kernel can leak idr in the error path of tcf_ife_init(), because
tcf_idr_release() is not called after successful idr reservation:
# $TC actions add action ife encode allow tcindex index 47
IFE type 0xED3E
RTNETLINK answers: No such file or directory
We have an error talking to the kernel
# $TC actions add action ife encode allow tcindex index 47
IFE type 0xED3E
RTNETLINK answers: No space left on device
We have an error talking to the kernel
# $TC actions add action ife encode use mark 7 type 0xfefe pass index 47
IFE type 0xFEFE
RTNETLINK answers: No space left on device
We have an error talking to the kernel
Since tcfa_lock is already taken when the action is being edited, a call
to tcf_idr_release() wrongly makes tcf_idr_cleanup() take the same lock
again. On the other hand, tcf_idr_release() needs to be called in the
error path of tcf_ife_init(), to undo the last tcf_idr_create() invocation.
Fix both problems in tcf_ife_init().
Since the cleanup() routine can now be called when ife->params is NULL,
also add a NULL pointer check to avoid calling kfree_rcu(NULL, rcu).
[1]
============================================
WARNING: possible recursive locking detected
4.17.0-rc4.kasan+ #417 Tainted: G E
--------------------------------------------
tc/3932 is trying to acquire lock:
000000005097c9a6 (&(&p->tcfa_lock)->rlock){+...}, at: tcf_ife_cleanup+0x19/0x80 [act_ife]
but task is already holding lock:
000000005097c9a6 (&(&p->tcfa_lock)->rlock){+...}, at: tcf_ife_init+0xf6d/0x13c0 [act_ife]
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&p->tcfa_lock)->rlock);
lock(&(&p->tcfa_lock)->rlock);
*** DEADLOCK ***
May be due to missing lock nesting notation
2 locks held by tc/3932:
#0: 000000007ca8e990 (rtnl_mutex){+.+.}, at: tcf_ife_init+0xf61/0x13c0 [act_ife]
#1: 000000005097c9a6 (&(&p->tcfa_lock)->rlock){+...}, at: tcf_ife_init+0xf6d/0x13c0 [act_ife]
stack backtrace:
CPU: 3 PID: 3932 Comm: tc Tainted: G E 4.17.0-rc4.kasan+ #417
Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
Call Trace:
dump_stack+0x9a/0xeb
__lock_acquire+0xf43/0x34a0
? debug_check_no_locks_freed+0x2b0/0x2b0
? debug_check_no_locks_freed+0x2b0/0x2b0
? debug_check_no_locks_freed+0x2b0/0x2b0
? __mutex_lock+0x62f/0x1240
? kvm_sched_clock_read+0x1a/0x30
? sched_clock+0x5/0x10
? sched_clock_cpu+0x18/0x170
? find_held_lock+0x39/0x1d0
? lock_acquire+0x10b/0x330
lock_acquire+0x10b/0x330
? tcf_ife_cleanup+0x19/0x80 [act_ife]
_raw_spin_lock_bh+0x38/0x70
? tcf_ife_cleanup+0x19/0x80 [act_ife]
tcf_ife_cleanup+0x19/0x80 [act_ife]
__tcf_idr_release+0xff/0x350
tcf_ife_init+0xdde/0x13c0 [act_ife]
? ife_exit_net+0x290/0x290 [act_ife]
? __lock_is_held+0xb4/0x140
tcf_action_init_1+0x67b/0xad0
? tcf_action_dump_old+0xa0/0xa0
? sched_clock+0x5/0x10
? sched_clock_cpu+0x18/0x170
? kvm_sched_clock_read+0x1a/0x30
? sched_clock+0x5/0x10
? sched_clock_cpu+0x18/0x170
? memset+0x1f/0x40
tcf_action_init+0x30f/0x590
? tcf_action_init_1+0xad0/0xad0
? memset+0x1f/0x40
tc_ctl_action+0x48e/0x5e0
? mutex_lock_io_nested+0x1160/0x1160
? tca_action_gd+0x990/0x990
? sched_clock+0x5/0x10
? find_held_lock+0x39/0x1d0
rtnetlink_rcv_msg+0x4da/0x990
? validate_linkmsg+0x680/0x680
? sched_clock_cpu+0x18/0x170
? find_held_lock+0x39/0x1d0
netlink_rcv_skb+0x127/0x350
? validate_linkmsg+0x680/0x680
? netlink_ack+0x970/0x970
? __kmalloc_node_track_caller+0x304/0x3a0
netlink_unicast+0x40f/0x5d0
? netlink_attachskb+0x580/0x580
? _copy_from_iter_full+0x187/0x760
? import_iovec+0x90/0x390
netlink_sendmsg+0x67f/0xb50
? netlink_unicast+0x5d0/0x5d0
? copy_msghdr_from_user+0x206/0x340
? netlink_unicast+0x5d0/0x5d0
sock_sendmsg+0xb3/0xf0
___sys_sendmsg+0x60a/0x8b0
? copy_msghdr_from_user+0x340/0x340
? lock_downgrade+0x5e0/0x5e0
? tty_write_lock+0x18/0x50
? kvm_sched_clock_read+0x1a/0x30
? sched_clock+0x5/0x10
? sched_clock_cpu+0x18/0x170
? find_held_lock+0x39/0x1d0
? lock_downgrade+0x5e0/0x5e0
? lock_acquire+0x10b/0x330
? __audit_syscall_entry+0x316/0x690
? current_kernel_time64+0x6b/0xd0
? __fget_light+0x55/0x1f0
? __sys_sendmsg+0xd2/0x170
__sys_sendmsg+0xd2/0x170
? __ia32_sys_shutdown+0x70/0x70
? syscall_trace_enter+0x57a/0xd60
? rcu_read_lock_sched_held+0xdc/0x110
? __bpf_trace_sys_enter+0x10/0x10
? do_syscall_64+0x22/0x480
do_syscall_64+0xa5/0x480
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x7fd646988ba0
RSP: 002b:00007fffc9fab3c8 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00007fffc9fab4f0 RCX: 00007fd646988ba0
RDX: 0000000000000000 RSI: 00007fffc9fab440 RDI: 0000000000000003
RBP: 000000005b28c8b3 R08: 0000000000000002 R09: 0000000000000000
R10: 00007fffc9faae20 R11: 0000000000000246 R12: 0000000000000000
R13: 00007fffc9fab504 R14: 0000000000000001 R15: 000000000066c100
Fixes: 4e8c861550 ("net sched: net sched: ife action fix late binding")
Fixes: ef6980b6be ("introduce IFE action")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 271f7ff5aa ]
When using s/w buffer management, buffers are allocated and DMA mapped.
When doing so on an arm64 platform, an offset correction is applied on
the DMA address, before storing it in an Rx descriptor. The issue is
this DMA address is then used later in the Rx path without removing the
offset correction. Thus the DMA address is wrong, which can led to
various issues.
This patch fixes this by removing the offset correction from the DMA
address retrieved from the Rx descriptor before using it in the Rx path.
Fixes: 8d5047cf9c ("net: mvneta: Convert to be 64 bits compatible")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 603b7bcff8 ]
The NULL character was not set correctly for the string containing
the command length, this caused failures reading the output of the
command due to a random length. The fix is to initialize the output
length string.
Fixes: e126ba97db ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d412c31dae ]
The command interface can work in two modes: Events and Polling.
In the general case, each time we invoke a command, a work is
queued to handle it.
When working in events, the interrupt handler completes the
command execution. On the other hand, when working in polling
mode, the work itself completes it.
Due to a bug in the work handler, a command could have been
completed by the interrupt handler, while the work handler
hasn't finished yet, causing the it to complete once again
if the command interface mode was changed from Events to
polling after the interrupt handler was called.
mlx5_unload_one()
mlx5_stop_eqs()
// Destroy the EQ before cmd EQ
...cmd_work_handler()
write_doorbell()
--> EVENT_TYPE_CMD
mlx5_cmd_comp_handler() // First free
free_ent(cmd, ent->idx)
complete(&ent->done)
<-- mlx5_stop_eqs //cmd was complete
// move to polling before destroying the last cmd EQ
mlx5_cmd_use_polling()
cmd->mode = POLL;
--> cmd_work_handler (continues)
if (cmd->mode == POLL)
mlx5_cmd_comp_handler() // Double free
The solution is to store the cmd->mode before writing the doorbell.
Fixes: e126ba97db ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0efc856249 ]
In smartnic env, the host (PF) driver might not be an e-switch
manager, hence the FW will err on driver attempts to deal with
setting/unsetting the eswitch and as a result the overall setup
of sriov will fail.
Fix that by avoiding the operation if e-switch management is not
allowed for this driver instance. While here, move to use the
correct name for the esw manager capability name.
Fixes: 81848731ff ('net/mlx5: E-Switch, Add SR-IOV (FDB) support')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Guy Kushnir <guyk@mellanox.com>
Reviewed-by: Eli Cohen <eli@melloanox.com>
Tested-by: Eli Cohen <eli@melloanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8ffd569aaa ]
The check for cpu hit statistics was not returning immediate false for
any non vport rep netdev and hence we crashed (say on mlx5 probed VFs) if
user-space tool was calling into any possible netdev in the system.
Fix that by doing a proper check before dereferencing.
Fixes: 1d447a3914 ('net/mlx5e: Extendable vport representor netdev private data')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Eli Cohen <eli@melloanox.com>
Reviewed-by: Eli Cohen <eli@melloanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 733d3e5497 ]
In smartnic env, the host (PF) driver might not be an e-switch
manager, hence the switchdev mode representors are running on
the embedded cpu (EC) and not at the host.
As such, we should avoid dealing with vport representors if
not being esw manager.
While here, make sure to disallow eswitch switchdev related
setups through devlink if we are not esw managers.
Fixes: cb67b83292 ('net/mlx5e: Introduce SRIOV VF representors')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 64d7839af8 ]
When delta passed to gem_ptp_adjtime is negative, the sign is
maintained in the ns_to_timespec64 conversion. Hence timespec_add
should be used directly. timespec_sub will just subtract the negative
value thus increasing the time difference.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 603d4cf8fe ]
Since the addition of GRO for ESP, gro_receive can consume the skb and
return -EINPROGRESS. In that case, the lower layer GRO handler cannot
touch the skb anymore.
Commit 5f114163f2 ("net: Add a skb_gro_flush_final helper.") converted
some of the gro_receive handlers that can lead to ESP's gro_receive so
that they wouldn't access the skb when -EINPROGRESS is returned, but
missed other spots, mainly in tunneling protocols.
This patch finishes the conversion to using skb_gro_flush_final(), and
adds a new helper, skb_gro_flush_final_remcsum(), used in VXLAN and
GUE.
Fixes: 5f114163f2 ("net: Add a skb_gro_flush_final helper.")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0ce4e70ff0 ]
To compute delays, better not use time of the day which can
be changed by admins or malicious programs.
Also change ccid3_first_li() to use s64 type for delta variable
to avoid potential overflows.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Cc: dccp@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ad088ec480 ]
The driver was combining the XDP_TX tail flush and XDP_REDIRECT
map flushing (xdp_do_flush_map). This is suboptimal, these two
flush operations should be kept separate.
Fixes: 11393cc9b9 ("xdp: Add batching support to redirect map")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 30877961b1 ]
Commit 296d485680 ("ipvlan: inherit MTU from master device") adjusted
the mtu from the master device when creating a ipvlan device, but it
would also override the mtu value set in rtnl_create_link. It causes
IFLA_MTU param not to take effect.
So this patch is to not adjust the mtu if IFLA_MTU param is set when
creating a ipvlan device.
Fixes: 296d485680 ("ipvlan: inherit MTU from master device")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fc9c2029e3 ]
The 'mask' argument to crypto_alloc_shash() uses the CRYPTO_ALG_* flags,
not 'gfp_t'. So don't pass GFP_KERNEL to it.
Fixes: bf355b8d2c ("ipv6: sr: add core files for SR HMAC support")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3ffe64f1a6 ]
When doing device hotplug the sub channel must be async to avoid
deadlock issues because device is discovered in softirq context.
When doing changes to MTU and number of channels, the setup
must be synchronous to avoid races such as when MTU and device
settings are done in a single ip command.
Reported-by: Thomas Walker <Thomas.Walker@twosigma.com>
Fixes: 8195b1396e ("hv_netvsc: fix deadlock on hotplug")
Fixes: 732e49850c ("netvsc: fix race on sub channel creation")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ced9e19150 ]
pool can be indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/atm/zatm.c:1491 zatm_ioctl() warn: potential spectre issue
'zatm_dev->pool_info' (local cap)
Fix this by sanitizing pool before using it to index
zatm_dev->pool_info
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9bbe60a67b ]
ATM accounts for in-flight TX packets in sk_wmem_alloc of the VCC on
which they are to be sent. But it doesn't take ownership of those
packets from the sock (if any) which originally owned them. They should
remain owned by their actual sender until they've left the box.
There's a hack in pskb_expand_head() to avoid adjusting skb->truesize
for certain skbs, precisely to avoid messing up sk_wmem_alloc
accounting. Ideally that hack would cover the ATM use case too, but it
doesn't — skbs which aren't owned by any sock, for example PPP control
frames, still get their truesize adjusted when the low-level ATM driver
adds headroom.
This has always been an issue, it seems. The truesize of a packet
increases, and sk_wmem_alloc on the VCC goes negative. But this wasn't
for normal traffic, only for control frames. So I think we just got away
with it, and we probably needed to send 2GiB of LCP echo frames before
the misaccounting would ever have caused a problem and caused
atm_may_send() to start refusing packets.
Commit 14afee4b60 ("net: convert sock.sk_wmem_alloc from atomic_t to
refcount_t") did exactly what it was intended to do, and turned this
mostly-theoretical problem into a real one, causing PPPoATM to fail
immediately as sk_wmem_alloc underflows and atm_may_send() *immediately*
starts refusing to allow new packets.
The least intrusive solution to this problem is to stash the value of
skb->truesize that was accounted to the VCC, in a new member of the
ATM_SKB(skb) structure. Then in atm_pop_raw() subtract precisely that
value instead of the then-current value of skb->truesize.
Fixes: 158f323b98 ("net: adjust skb->truesize in pskb_expand_head()")
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Tested-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bc800e8b39 ]
The __alx_open function can be called from ndo_open, which is called
under RTNL, or from alx_resume, which isn't. Since commit d768319cd4,
we're calling the netif_set_real_num_{tx,rx}_queues functions, which
need to be called under RTNL.
This is similar to commit 0c2cc02e57 ("igb: Move the calls to set the
Tx and Rx queues into igb_open").
Fixes: d768319cd4 ("alx: enable multiple tx queues")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit de227ed796 upstream.
If the pinctrl node has the gpio-ranges property, the range will be added
by the gpio core and doesn't need to be added by the pinctrl driver.
But for keeping backward compatibility, an explicit pinctrl_add_gpio_range
is still needed to be called when there is a missing gpio-ranges in pinctrl
node in old dts files.
Cc: stable@vger.kernel.org
Fixes: d6ed935513 ("pinctrl: mediatek: add pinctrl driver for MT7622 SoC")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 550b6f7e8c upstream.
The datasheet does not document any registers to control drive strength,
and no drive strength registers are for this reason described for this
SoC. The flags indicating that drive strength can be controlled are
however set for some pins in the driver.
This leads to a NULL pointer dereference when the sh-pfc core tries to
access the struct describing the drive strength registers, for example
when reading the sysfs file pinconf-pins.
Fix this by removing the SH_PFC_PIN_CFG_DRIVE_STRENGTH from all pins.
Fixes: b92ac66a18 ("pinctrl: sh-pfc: Add R8A77970 PFC support")
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d1b47a7c9e upstream.
Moving zero_resv_unavail before memmap_init_zone(), caused a regression on
x86-32.
The cause is that we access struct pages before they are allocated when
CONFIG_FLAT_NODE_MEM_MAP is used.
free_area_init_nodes()
zero_resv_unavail()
mm_zero_struct_page(pfn_to_page(pfn)); <- struct page is not alloced
free_area_init_node()
if CONFIG_FLAT_NODE_MEM_MAP
alloc_node_mem_map()
memblock_virt_alloc_node_nopanic() <- struct page alloced here
On the other hand memblock_virt_alloc_node_nopanic() zeroes all the memory
that it returns, so we do not need to do zero_resv_unavail() here.
Fixes: e181ae0c5d ("mm: zero unavailable pages before memmap init")
Signed-off-by: Pavel Tatashin <pasha.tatashin@oracle.com>
Tested-by: Matt Hart <matt@mattface.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 568cc2f07c upstream.
Commit 2f28e4c24b (thermal: armada: Clarify control registers
accesses) introduced the new thermal binding. The new binding extends
the second registers field size to 8. Switch to the new binding to fix
thermal reading values. Without this change the fix for errata #132698
introduced in commit 8c0b888f66 (thermal: armada: Change sensors trim
default value) has no effect.
Cc: stable@vger.kernel.org # v4.16+
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0447378a4a upstream.
This patch extends the checks done prior to a nested VM entry.
Specifically, it extends the check_vmentry_prereqs function with checks
for fields relevant to the VM-entry event injection information, as
described in the Intel SDM, volume 3.
This patch is motivated by a syzkaller bug, where a bad VM-entry
interruption information field is generated in the VMCS02, which causes
the nested VM launch to fail. Then, KVM fails to resume L1.
While KVM should be improved to correctly resume L1 execution after a
failed nested launch, this change is justified because the existing code
to resume L1 is flaky/ad-hoc and the test coverage for resuming L1 is
sparse.
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Marc Orr <marcorr@google.com>
[Removed comment whose parts were describing previous revisions and the
rest was obvious from function/variable naming. - Radim]
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a8690ed6f upstream.
In commit 357d23c811a7 ("Remove the obsolete libibcm library")
in rdma-core [1], we removed obsolete library which used the
/dev/infiniband/ucmX interface.
Following multiple syzkaller reports about non-sanitized
user input in the UCMA module, the short audit reveals the same
issues in UCM module too.
It is better to disable this interface in the kernel,
before syzkaller team invests time and energy to harden
this unused interface.
[1] https://github.com/linux-rdma/rdma-core/pull/279
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c568503ef0 upstream.
syzbot reports following splat:
BUG: KMSAN: uninit-value in ebt_stp_mt_check+0x24b/0x450
net/bridge/netfilter/ebt_stp.c:162
ebt_stp_mt_check+0x24b/0x450 net/bridge/netfilter/ebt_stp.c:162
xt_check_match+0x1438/0x1650 net/netfilter/x_tables.c:506
ebt_check_match net/bridge/netfilter/ebtables.c:372 [inline]
ebt_check_entry net/bridge/netfilter/ebtables.c:702 [inline]
The uninitialised access is
xt_mtchk_param->nft_compat
... which should be set to 0.
Fix it by zeroing the struct beforehand, same for tgchk.
ip(6)tables targetinfo uses c99-style initialiser, so no change
needed there.
Reported-by: syzbot+da4494182233c23a5fcf@syzkaller.appspotmail.com
Fixes: 55917a21d0 ("netfilter: x_tables: add context to know if extension runs from nft_compat")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b7b73cd5d7 upstream.
The x86 assembly implementations of Salsa20 use the frame base pointer
register (%ebp or %rbp), which breaks frame pointer convention and
breaks stack traces when unwinding from an interrupt in the crypto code.
Recent (v4.10+) kernels will warn about this, e.g.
WARNING: kernel stack regs at 00000000a8291e69 in syzkaller047086:4677 has bad 'bp' value 000000001077994c
[...]
But after looking into it, I believe there's very little reason to still
retain the x86 Salsa20 code. First, these are *not* vectorized
(SSE2/SSSE3/AVX2) implementations, which would be needed to get anywhere
close to the best Salsa20 performance on any remotely modern x86
processor; they're just regular x86 assembly. Second, it's still
unclear that anyone is actually using the kernel's Salsa20 at all,
especially given that now ChaCha20 is supported too, and with much more
efficient SSSE3 and AVX2 implementations. Finally, in benchmarks I did
on both Intel and AMD processors with both gcc 8.1.0 and gcc 4.9.4, the
x86_64 salsa20-asm is actually slightly *slower* than salsa20-generic
(~3% slower on Skylake, ~10% slower on Zen), while the i686 salsa20-asm
is only slightly faster than salsa20-generic (~15% faster on Skylake,
~20% faster on Zen). The gcc version made little difference.
So, the x86_64 salsa20-asm is pretty clearly useless. That leaves just
the i686 salsa20-asm, which based on my tests provides a 15-20% speed
boost. But that's without updating the code to not use %ebp. And given
the maintenance cost, the small speed difference vs. salsa20-generic,
the fact that few people still use i686 kernels, the doubt that anyone
is even using the kernel's Salsa20 at all, and the fact that a SSE2
implementation would almost certainly be much faster on any remotely
modern x86 processor yet no one has cared enough to add one yet, I don't
think it's worthwhile to keep.
Thus, just remove both the x86_64 and i686 salsa20-asm implementations.
Reported-by: syzbot+ffa3a158337bbc01ff09@syzkaller.appspotmail.com
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 70dbcc2254 upstream.
Fix a regression introduced in Linux kernel 4.17 where sending a SCSI
command that does not transfer data (such as TEST UNIT READY) via
/dev/bsg/* results in EINVAL.
Fixes: 17cb960f29 ("bsg: split handling of SCSI CDBs vs transport requeues")
Cc: <stable@vger.kernel.org> # 4.17+
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0ce0bba4e5 upstream.
Setting pv_irq_ops for Xen PV domains should be done as early as
possible in order to support e.g. very early printk() usage.
The same applies to xen_vcpu_info_reset(0), as it is needed for the
pv irq ops.
Move the call of xen_setup_machphys_mapping() after initializing the
pv functions as it contains a WARN_ON(), too.
Remove the no longer necessary conditional in xen_init_irq_ops()
from PVH V1 times to make clear this is a PV only function.
Cc: <stable@vger.kernel.org> # 4.14
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e69b5d308d upstream.
When removing the global bit from __supported_pte_mask do the same for
__default_kernel_pte_mask in order to avoid the WARN_ONCE() in
check_pgprot() when setting a kernel pte before having called
init_mem_mapping().
Cc: <stable@vger.kernel.org> # 4.17
Reported-by: Michael Young <m.a.young@durham.ac.uk>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b72717a20 upstream.
The code was mistakenly using the length of the page array memory instead
of the depth of the page array.
This would cause MR creation to fail in some cases.
Fixes: 8376b86de7 ("iw_cxgb4: Support the new memory registration API")
Cc: stable@vger.kernel.org
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit abe41184ab upstream.
I2C clients may misunderstand recovery pulses if they can't read SDA to
bail out early. In the worst case, as a write operation. To avoid that
and if we can write SDA, try to send STOP to avoid the
misinterpretation.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54836e2d03 upstream.
On Tegra30 Cardhu the PCA9546 I2C mux is not ACK'ing I2C commands on
resume from suspend (which is caused by the reset signal for the I2C
mux not being configured correctl). However, this NACK is causing the
Tegra30 to hang on resuming from suspend which is not expected as we
detect NACKs and handle them. The hang observed appears to occur when
resetting the I2C controller to recover from the NACK.
Commit 77821b4678 ("i2c: tegra: proper handling of error cases") added
additional error handling for some error cases including NACK, however,
it appears that this change conflicts with an early fix by commit
f70893d083 ("i2c: tegra: Add delay before resetting the controller
after NACK"). After commit 77821b4678 was made we now disable 'packet
mode' before the delay from commit f70893d083 happens. Testing shows
that moving the delay to before disabling 'packet mode' fixes the hang
observed on Tegra30. The delay was added to give the I2C controller
chance to send a stop condition and so it makes sense to move this to
before we disable packet mode. Please note that packet mode is always
enabled for Tegra.
Fixes: 77821b4678 ("i2c: tegra: proper handling of error cases")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b697d7d8c7 upstream.
The __get_txreq() function can return a pointer, ERR_PTR(-EBUSY), or NULL.
All of the relevant call sites look for IS_ERR, so the NULL return would
lead to a NULL pointer exception.
Do not use the ERR_PTR mechanism for this function.
Update all call sites to handle the return value correctly.
Clean up error paths to reflect return value.
Fixes: 45842abbb2 ("staging/rdma/hfi1: move txreq header code")
Cc: <stable@vger.kernel.org> # 4.9.x+
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Kamenee Arumugam <kamenee.arumugam@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9feeb638cd upstream.
In 2016 GNU Make made a backwards incompatible change to the way '#'
characters were handled in Makefiles when used inside functions or
macros:
http://git.savannah.gnu.org/cgit/make.git/commit/?id=c6966b323811c37acedff05b57
Due to this change, when attempting to run `make prepare' I get a
spurious make syntax error:
/home/earnest/linux/tools/objtool/.fixdep.o.cmd:1: *** missing separator. Stop.
When inspecting `.fixdep.o.cmd' it includes two lines which use
unescaped comment characters at the top:
\# cannot find fixdep (/home/earnest/linux/tools/objtool//fixdep)
\# using basic dep data
This is because `tools/build/Build.include' prints these '\#'
characters:
printf '\# cannot find fixdep (%s)\n' $(fixdep) > $(dot-target).cmd; \
printf '\# using basic dep data\n\n' >> $(dot-target).cmd; \
This completes commit 9564a8cf42 ("Kbuild: fix # escaping in .cmd files
for future Make").
Link: https://bugzilla.kernel.org/show_bug.cgi?id=197847
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: stable@vger.kernel.org
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2fd8eb4ad8 upstream.
It does not matter if the caller of may_use_simd() migrates to
another cpu after the call, but it is still important that the
kernel_neon_busy percpu instance that is read matches the cpu the
task is running on at the time of the read.
This means that raw_cpu_read() is not sufficient. kernel_neon_busy
may appear true if the caller migrates during the execution of
raw_cpu_read() and the next task to be scheduled in on the initial
cpu calls kernel_neon_begin().
This patch replaces raw_cpu_read() with this_cpu_read() to protect
against this race.
Cc: <stable@vger.kernel.org>
Fixes: cb84d11e16 ("arm64: neon: Remove support for nested or hardirq kernel-mode NEON")
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Yandong Zhao <yandong77520@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 33cc2c9667 upstream.
The notification of scrub completion happens within the scrub workqueue.
That can clearly race someone running scrub_show() and work_busy()
before the workqueue has a chance to flush the recently completed work.
Add a flag to reliably indicate the idle vs busy state. Without this
change applications using poll(2) to wait for scrub-completion may
falsely wakeup and read ARS as being busy even though the thread is
going idle and then hang indefinitely.
Fixes: bc6ba80858 ("nfit, address-range-scrub: rework and simplify ARS...")
Cc: <stable@vger.kernel.org>
Reported-by: Vishal Verma <vishal.l.verma@intel.com>
Tested-by: Vishal Verma <vishal.l.verma@intel.com>
Reported-by: Lukasz Dorau <lukasz.dorau@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f8494fa3dd upstream.
Currently ftrace displays data in trace output like so:
_-----=> irqs-off
/ _----=> need-resched
| / _---=> hardirq/softirq
|| / _--=> preempt-depth
||| / delay
TASK-PID CPU TGID |||| TIMESTAMP FUNCTION
| | | | |||| | |
bash-1091 [000] ( 1091) d..2 28.313544: sched_switch:
However Android's trace visualization tools expect a slightly different
format due to an out-of-tree patch patch that was been carried for a
decade, notice that the TGID and CPU fields are reversed:
_-----=> irqs-off
/ _----=> need-resched
| / _---=> hardirq/softirq
|| / _--=> preempt-depth
||| / delay
TASK-PID TGID CPU |||| TIMESTAMP FUNCTION
| | | | |||| | |
bash-1091 ( 1091) [002] d..2 64.965177: sched_switch:
From kernel v4.13 onwards, during which TGID was introduced, tracing
with systrace on all Android kernels will break (most Android kernels
have been on 4.9 with Android patches, so this issues hasn't been seen
yet). From v4.13 onwards things will break.
The chrome browser's tracing tools also embed the systrace viewer which
uses the legacy TGID format and updates to that are known to be
difficult to make.
Considering this, I suggest we make this change to the upstream kernel
and backport it to all Android kernels. I believe this feature is merged
recently enough into the upstream kernel that it shouldn't be a problem.
Also logically, IMO it makes more sense to group the TGID with the
TASK-PID and the CPU after these.
Link: http://lkml.kernel.org/r/20180626000822.113931-1-joel@joelfernandes.org
Cc: jreck@google.com
Cc: tkjos@google.com
Cc: stable@vger.kernel.org
Fixes: 441dae8f2f ("tracing: Add support for display of tgid in trace output")
Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb177a732c upstream.
syzbot has noticed that a specially crafted library can easily hit
VM_BUG_ON in __mm_populate
kernel BUG at mm/gup.c:1242!
invalid opcode: 0000 [#1] SMP
CPU: 2 PID: 9667 Comm: a.out Not tainted 4.18.0-rc3 #644
Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 05/19/2017
RIP: 0010:__mm_populate+0x1e2/0x1f0
Code: 55 d0 65 48 33 14 25 28 00 00 00 89 d8 75 21 48 83 c4 20 5b 41 5c 41 5d 41 5e 41 5f 5d c3 e8 75 18 f1 ff 0f 0b e8 6e 18 f1 ff <0f> 0b 31 db eb c9 e8 93 06 e0 ff 0f 1f 00 55 48 89 e5 53 48 89 fb
Call Trace:
vm_brk_flags+0xc3/0x100
vm_brk+0x1f/0x30
load_elf_library+0x281/0x2e0
__ia32_sys_uselib+0x170/0x1e0
do_fast_syscall_32+0xca/0x420
entry_SYSENTER_compat+0x70/0x7f
The reason is that the length of the new brk is not page aligned when we
try to populate the it. There is no reason to bug on that though.
do_brk_flags already aligns the length properly so the mapping is
expanded as it should. All we need is to tell mm_populate about it.
Besides that there is absolutely no reason to to bug_on in the first
place. The worst thing that could happen is that the last page wouldn't
get populated and that is far from putting system into an inconsistent
state.
Fix the issue by moving the length sanitization code from do_brk_flags
up to vm_brk_flags. The only other caller of do_brk_flags is brk
syscall entry and it makes sure to provide the proper length so t here
is no need for sanitation and so we can use do_brk_flags without it.
Also remove the bogus BUG_ONs.
[osalvador@techadventures.net: fix up vm_brk_flags s@request@len@]
Link: http://lkml.kernel.org/r/20180706090217.GI32658@dhcp22.suse.cz
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reported-by: syzbot <syzbot+5dcb560fe12aa5091c06@syzkaller.appspotmail.com>
Tested-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Cc: Zi Yan <zi.yan@cs.rutgers.edu>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: "Huang, Ying" <ying.huang@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fa8cbda88d upstream.
- Build the kernel without the fix
- Add some flag to the purgatories KBUILD_CFLAGS,I used
-fno-asynchronous-unwind-tables
- Re-build the kernel
When you look at makes output you see that sha256.o is not re-build in the
last step. Also readelf -S still shows the .eh_frame section for
sha256.o.
With the fix sha256.o is rebuilt in the last step.
Without FORCE make does not detect changes only made to the command line
options. So object files might not be re-built even when they should be.
Fix this by adding FORCE where it is missing.
Link: http://lkml.kernel.org/r/20180704110044.29279-2-prudo@linux.ibm.com
Fixes: df6f2801f5 ("kernel/kexec_file.c: move purgatories sha256 to common code")
Signed-off-by: Philipp Rudo <prudo@linux.ibm.com>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@vger.kernel.org> [4.17+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e70cc2bd57 upstream.
Thomas reports:
"While looking around in /proc on my v4.14.52 system I noticed that all
processes got a lot of "Locked" memory in /proc/*/smaps. A lot more
memory than a regular user can usually lock with mlock().
Commit 493b0e9d94 (in v4.14-rc1) seems to have changed the behavior
of "Locked".
Before that commit the code was like this. Notice the VM_LOCKED check.
(vma->vm_flags & VM_LOCKED) ?
(unsigned long)(mss.pss >> (10 + PSS_SHIFT)) : 0);
After that commit Locked is now the same as Pss:
(unsigned long)(mss->pss >> (10 + PSS_SHIFT)));
This looks like a mistake."
Indeed, the commit has added mss->pss_locked with the correct value that
depends on VM_LOCKED, but forgot to actually use it. Fix it.
Link: http://lkml.kernel.org/r/ebf6c7fb-fec3-6a26-544f-710ed193c154@suse.cz
Fixes: 493b0e9d94 ("mm: add /proc/pid/smaps_rollup")
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Reported-by: Thomas Lindroth <thomas.lindroth@gmail.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Daniel Colascione <dancol@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aaa23f8600 upstream.
Obtaining the runtime pm wakeref can fail, especially in a hotplug
scenario where i915.ko has been unloaded. If we do not catch the
failure, we end up with an unbalanced pm.
v2 additions by tiwai:
hdmi_present_sense() checks the return value and handle only a
negative error case and bails out only if it's really still suspended.
Also, snd_hda_power_down() is called at the error path so that the
refcount is balanced.
Along with it, the spec->pcm_lock is taken outside
hdmi_present_sense() in the caller side, so that it won't cause
deadlock at reentrace via runtime resume.
v3 fix by tiwai:
Missing linux/pm_runtime.h is included.
References: 222bde0388 ("ALSA: hda - Fix mutex deadlock at HDMI/DP hotplug")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c6b17f1020 upstream.
We have two new lenovo desktop models which need to apply the fixup of
ALC294_FIXUP_LENOVO_MIC_LOCATION, and they have the same pin cfg as
the machine with subsystem id:0x17aa3136, now use the pincfg table
to apply the fixup for them.
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e181ae0c5d upstream.
We must zero struct pages for memory that is not backed by physical
memory, or kernel does not have access to.
Recently, there was a change which zeroed all memmap for all holes in
e820. Unfortunately, it introduced a bug that is discussed here:
https://www.spinics.net/lists/linux-mm/msg156764.html
Linus, also saw this bug on his machine, and confirmed that reverting
commit 124049decb ("x86/e820: put !E820_TYPE_RAM regions into
memblock.reserved") fixes the issue.
The problem is that we incorrectly zero some struct pages after they
were setup.
The fix is to zero unavailable struct pages prior to initializing of
struct pages.
A more detailed fix should come later that would avoid double zeroing
cases: one in __init_single_page(), the other one in
zero_resv_unavail().
Fixes: 124049decb ("x86/e820: put !E820_TYPE_RAM regions into memblock.reserved")
Signed-off-by: Pavel Tatashin <pasha.tatashin@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0fa3ecd878 upstream.
sgid directories have special semantics, making newly created files in
the directory belong to the group of the directory, and newly created
subdirectories will also become sgid. This is historically used for
group-shared directories.
But group directories writable by non-group members should not imply
that such non-group members can magically join the group, so make sure
to clear the sgid bit on non-directories for non-members (but remember
that sgid without group execute means "mandatory locking", just to
confuse things even more).
Reported-by: Jann Horn <jannh@google.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 313db3d648 upstream.
The > should be >= here so that we don't read one element beyond the end
of the ep->stream_info->stream_rings[] array.
Fixes: e9df17eb14 ("USB: xhci: Correct assumptions about number of rings per endpoint.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bba57eddad upstream.
Corsair Strafe appears to suffer from the same issues
as the Corsair Strafe RGB.
Apply the same quirks (control message delay and init delay)
that the RGB version has to 1b1c:1b15.
With these quirks in place the keyboard works correctly upon
booting the system, and no longer requires reattaching the device.
Signed-off-by: Nico Sneck <snecknico@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f1e255d60a upstream.
In general, accessing userspace memory beyond the length of the supplied
buffer in VFS read/write handlers can lead to both kernel memory corruption
(via kernel_read()/kernel_write(), which can e.g. be triggered via
sys_splice()) and privilege escalation inside userspace.
Fix it by using simple_read_from_buffer() instead of custom logic.
Fixes: 6bc235a2e2 ("USB: add driver for Meywa-Denki & Kayac YUREX")
Signed-off-by: Jann Horn <jannh@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 01b3cdfca2 upstream.
Fix broken modem-status error handling which could lead to bits of slab
data leaking to user space.
Fixes: 3b36a8fd67 ("usb: fix uninitialized variable warning in keyspan_pda")
Cc: stable <stable@vger.kernel.org> # 2.6.27
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e33eab9ded upstream.
The "r" variable is an int and "bufsize" is an unsigned int so the
comparison is type promoted to unsigned. If usb_control_msg() returns a
negative that is treated as a high positive value and the error handling
doesn't work.
Fixes: 2d5a9c72d0 ("USB: serial: ch341: fix control-message error handling")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 007a74907d upstream.
The commit 9aaa3b8b4c ("thunderbolt: Add support for preboot ACL")
introduced boot_acl attribute but missed the fact that now userspace
needs to poll the attribute constantly to find out whether it has
changed or not. Fix this by sending notification to the userspace
whenever the boot_acl attribute is changed.
Fixes: 9aaa3b8b4c ("thunderbolt: Add support for preboot ACL")
Reported-and-tested-by: Christian Kellner <christian@kellner.me>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Christian Kellner <christian@kellner.me>
Acked-by: Yehezkel Bernat <yehezkelshb@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 240630e618 upstream.
There have been several reports of LPM related hard freezes about once
a day on multiple Lenovo 50 series models. Strange enough these reports
where not disk model specific as LPM issues usually are and some users
with the exact same disk + laptop where seeing them while other users
where not seeing these issues.
It turns out that enabling LPM triggers a firmware bug somewhere, which
has been fixed in later BIOS versions.
This commit adds a new ahci_broken_lpm() function and a new ATA_FLAG_NO_LPM
for dealing with this.
The ahci_broken_lpm() function contains DMI match info for the 4 models
which are known to be affected by this and the DMI BIOS date field for
known good BIOS versions. If the BIOS date is older then the one in the
table LPM will be disabled and a warning will be printed.
Note the BIOS dates are for known good versions, some older versions may
work too, but we don't know for sure, the table is using dates from BIOS
versions for which users have confirmed that upgrading to that version
makes the problem go away.
Unfortunately I've been unable to get hold of the reporter who reported
that BIOS version 2.35 fixed the problems on the W541 for him. I've been
able to verify the DMI_SYS_VENDOR and DMI_PRODUCT_VERSION from an older
dmidecode, but I don't know the exact BIOS date as reported in the DMI.
Lenovo keeps a changelog with dates in their release notes, but the
dates there are the release dates not the build dates which are in DMI.
So I've chosen to set the date to which we compare to one day past the
release date of the 2.34 BIOS. I plan to fix this with a follow up
commit once I've the necessary info.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 90d72ce079 upstream.
Embarrassingly, the recent fix introduced worse problem than it solved,
causing the balloon not to inflate. The VM informed the hypervisor that
the pages for lock/unlock are sitting in the wrong address, as it used
the page that is used the uninitialized page variable.
Fixes: b23220fe05 ("vmw_balloon: fixing double free when batching mode is off")
Cc: stable@vger.kernel.org
Reviewed-by: Xavier Deguillard <xdeguillard@vmware.com>
Signed-off-by: Nadav Amit <namit@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aa7eee8a14 upstream.
Sometimes when writing large size files to flash in direct/memory mapped
mode, it is seen that flash write enable command times out with error:
[ 503.146293] cadence-qspi 47040000.ospi: Flash command execution timed out.
This is because, we need to make sure previous direct write operation
is complete by polling for IDLE bit in CONFIG_REG before starting the
next operation.
Fix this by polling for IDLE bit after memory mapped write.
Fixes: a27f2eaf2b ("mtd: spi-nor: cadence-quadspi: Add support for direct access mode")
Cc: stable@vger.kernel.org
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b7a020bff3 upstream.
This fixes regression introduced by
commit 8d52af6795 ("mei: speed up the power down flow")
In power down or suspend flow a message can still be received
from the FW because the clients fake disconnection.
In normal case we interpret messages w/o destination as corrupted
and link reset is performed in order to clean the channel,
but during power down link reset is already in progress resulting
in endless loop. To resolve the issue under power down flow we
discard messages silently.
Cc: <stable@vger.kernel.org> 4.16+
Fixes: 8d52af6795 ("mei: speed up the power down flow")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=199541
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b320a0a9f2 upstream.
The block (LBA) specified must not exceed the last addressable LBA,
which is dev->nr_sectors - 1. So fix the correct check is
"if (block >= dev->n_sectors)" and not "if (block > dev->n_sectords)".
Additionally, the asc/ascq to return for an LBA that is not a zone start
LBA should be ILLEGAL REQUEST, regardless if the bad LBA is out of
range.
Reported-by: David Butterfield <david.butterfield@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d59d2f9995 upstream.
RTL8822be can't bring up properly on ASUS X530UN, and dmesg says:
[ 8.591333] r8822be: module is from the staging directory, the quality
is unknown, you have been warned.
[ 8.593122] r8822be 0000:02:00.0: enabling device (0000 -> 0003)
[ 8.669163] r8822be: Using firmware rtlwifi/rtl8822befw.bin
[ 9.289939] r8822be: rtlwifi: wireless switch is on
[ 10.056426] r8822be 0000:02:00.0 wlp2s0: renamed from wlan0
...
[ 11.952534] r8822be: halmac_init_hal failed
[ 11.955933] r8822be: halmac_init_hal failed
[ 11.956227] r8822be: halmac_init_hal failed
[ 22.007942] r8822be: halmac_init_hal failed
Jian-Hong reported it works if turn off ASPM with module parameter aspm=0.
In order to fix this problem kindly, this commit don't turn off aspm but
enlarge ASPM L1 latency to 7.
Reported-by: Jian-Hong Pan <jian-hong@endlessm.com>
Tested-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a0341fc198 upstream.
This read handler had a lot of custom logic and wrote outside the bounds of
the provided buffer. This could lead to kernel and userspace memory
corruption. Just use simple_read_from_buffer() with a stack buffer.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 25a98edd57 upstream.
This patch is fixes an issue that the SDHI_INTERNAL_DMAC_RX_IN_USE
flag cannot be cleared because tmio_mmc_core sets the host->data
to NULL before the tmio_mmc_core calls tmio_mmc_abort_dma().
So, this patch clears the SDHI_INTERNAL_DMAC_RX_IN_USE in
the renesas_sdhi_internal_dmac_abort_dma() anyway. This doesn't
cause any side effects.
Fixes: 0cbc94daa5 ("mmc: renesas_sdhi_internal_dmac: limit DMA RX for old SoCs")
Cc: <stable@vger.kernel.org> # v4.17+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a6b9f4d60 upstream.
Card write threshold control is supposed to be set since controller
version 2.80a for data write in HS400 mode and data read in
HS200/HS400/SDR104 mode. However the current code returns without
configuring it in the case of data writing in HS400 mode.
Meanwhile the patch fixes that the current code goes to
'disable' when doing data reading in HS400 mode.
Fixes: 7e4bf1bc95 ("mmc: dw_mmc: add the card write threshold for HS400 mode")
Signed-off-by: Qing Xia <xiaqing17@hisilicon.com>
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 92748beac0 upstream.
If pinctrl nodes for 100/200MHz are missing, the controller should
not select any mode which need signal frequencies 100MHz or higher.
To prevent such speed modes the driver currently uses the quirk flag
SDHCI_QUIRK2_NO_1_8_V. This works nicely for SD cards since 1.8V
signaling is required for all faster modes and slower modes use 3.3V
signaling only.
However, there are eMMC modes which use 1.8V signaling and run below
100MHz, e.g. DDR52 at 1.8V. With using SDHCI_QUIRK2_NO_1_8_V this
mode is prevented. When using a fixed 1.8V regulator as vqmmc-supply
the stack has no valid mode to use. In this tenuous situation the
kernel continuously prints voltage switching errors:
mmc1: Switching to 3.3V signalling voltage failed
Avoid using SDHCI_QUIRK2_NO_1_8_V and prevent faster modes by
altering the SDHCI capability register. With that the stack is able
to select 1.8V modes even if no faster pinctrl states are available:
# cat /sys/kernel/debug/mmc1/ios
...
timing spec: 8 (mmc DDR52)
signal voltage: 1 (1.80 V)
...
Link: http://lkml.kernel.org/r/20180628081331.13051-1-stefan@agner.ch
Signed-off-by: Stefan Agner <stefan@agner.ch>
Fixes: ad93220de7 ("mmc: sdhci-esdhc-imx: change pinctrl state according
to uhs mode")
Cc: <stable@vger.kernel.org> # v4.13+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fa85015c0d upstream.
After commit 18996f2db9 (ACPICA: Events: Stop unconditionally
clearing ACPI IRQs during suspend/resume) the status of ACPI events
is not cleared any more when entering the ACPI S5 system state (power
off) which causes some systems to power up immediately after turing
off power in certain situations.
That is a functional regression, so address it by making the code
clear the status of all ACPI events again when entering S5 (for
system-wide suspend or hibernation the clearing of the status of all
events is not desirable, as it might cause the kernel to miss wakeup
events sometimes).
Fixes: 18996f2db9 (ACPICA: Events: Stop unconditionally clearing ACPI IRQs during suspend/resume)
Reported-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Thomas Hänig <haenig@cosifan.de>
Cc: 4.17+ <stable@vger.kernel.org> # 4.17+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c83a726d6 upstream.
When the hangcheck handler was replaced by the DRM scheduler timeout
handling we dropped the forward progress check, as this might allow
clients to hog the GPU for a long time with a big job.
It turns out that even reasonably well behaved clients like the
Armada Xorg driver occasionally trip over the 500ms timeout. Bring
back the forward progress check to get rid of the userspace regression.
We would still like to fix userspace to submit smaller batches
if possible, but that is for another day.
Cc: <stable@vger.kernel.org>
Fixes: 6d7a20c077 (drm/etnaviv: replace hangcheck with scheduler timeout)
Reported-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf6ba3aeb2 upstream.
Russell King reported:
"When removing and reloading the etnaviv module, the following splat
occurs:
sysfs: cannot create duplicate filename '/devices/platform/etnaviv'
CPU: 0 PID: 1471 Comm: modprobe Not tainted 4.17.0+ #1608
Hardware name: Marvell Dove (Cubox)
Backtrace:
[<c00157d4>] (dump_backtrace) from [<c0015b8c>] (show_stack+0x18/0x1c)
r6:ef033e38 r5:ee07b340 r4:edb9d000 r3:00000000
[<c0015b74>] (show_stack) from [<c0620784>] (dump_stack+0x20/0x28)
[<c0620764>] (dump_stack) from [<c01bcd24>] (sysfs_warn_dup+0x5c/0x70)
[<c01bccc8>] (sysfs_warn_dup) from [<c01bce14>] (sysfs_create_dir_ns+0x90/0x98)
..."
Commit 246774d17f ("drm/etnaviv: remove the need for a gpu-subsystem
DT node") introduced DRM registration via
platform_device_register_simple(), but missed to call
platform_device_unregister() inside etnaviv_exit().
Fix the problem by calling platform_device_unregister() inside
etnaviv_exit(). While at it, also rearrange the function calls
in the exit path to make them happen in the opposite order of
registration.
Tested on a imx6-sabresd board.
Cc: <stable@vger.kernel.org>
Fixes: 246774d17f ("drm/etnaviv: remove the need for a gpu-subsystem DT node")
Reported-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 523402fa91 upstream.
We currently attempt to check whether a physical address range provided
to __ioremap() may be in use by the page allocator by examining the
value of PageReserved for each page in the region - lowmem pages not
marked reserved are presumed to be in use by the page allocator, and
requests to ioremap them fail.
The way we check this has been broken since commit 92923ca3aa ("mm:
meminit: only set page reserved in the memblock region"), because
memblock will typically not have any knowledge of non-RAM pages and
therefore those pages will not have the PageReserved flag set. Thus when
we attempt to ioremap a region outside of RAM we incorrectly fail
believing that the region is RAM that may be in use.
In most cases ioremap() on MIPS will take a fast-path to use the
unmapped kseg1 or xkphys virtual address spaces and never hit this path,
so the only way to hit it is for a MIPS32 system to attempt to ioremap()
an address range in lowmem with flags other than _CACHE_UNCACHED.
Perhaps the most straightforward way to do this is using
ioremap_uncached_accelerated(), which is how the problem was discovered.
Fix this by making use of walk_system_ram_range() to test the address
range provided to __ioremap() against only RAM pages, rather than all
lowmem pages. This means that if we have a lowmem I/O region, which is
very common for MIPS systems, we're free to ioremap() address ranges
within it. A nice bonus is that the test is no longer limited to lowmem.
The approach here matches the way x86 performed the same test after
commit c81c8a1eee ("x86, ioremap: Speed up check for RAM pages") until
x86 moved towards a slightly more complicated check using walk_mem_res()
for unrelated reasons with commit 0e4c12b45a ("x86/mm, resource: Use
PAGE_KERNEL protection for ioremap of memory pages").
Signed-off-by: Paul Burton <paul.burton@mips.com>
Reported-by: Serge Semin <fancer.lancer@gmail.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Fixes: 92923ca3aa ("mm: meminit: only set page reserved in the memblock region")
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org # v4.2+
Patchwork: https://patchwork.linux-mips.org/patch/19786/
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b63e132b64 upstream.
The current MIPS implementation of arch_trigger_cpumask_backtrace() is
broken because it attempts to use synchronous IPIs despite the fact that
it may be run with interrupts disabled.
This means that when arch_trigger_cpumask_backtrace() is invoked, for
example by the RCU CPU stall watchdog, we may:
- Deadlock due to use of synchronous IPIs with interrupts disabled,
causing the CPU that's attempting to generate the backtrace output
to hang itself.
- Not succeed in generating the desired output from remote CPUs.
- Produce warnings about this from smp_call_function_many(), for
example:
[42760.526910] INFO: rcu_sched detected stalls on CPUs/tasks:
[42760.535755] 0-...!: (1 GPs behind) idle=ade/140000000000000/0 softirq=526944/526945 fqs=0
[42760.547874] 1-...!: (0 ticks this GP) idle=e4a/140000000000000/0 softirq=547885/547885 fqs=0
[42760.559869] (detected by 2, t=2162 jiffies, g=266689, c=266688, q=33)
[42760.568927] ------------[ cut here ]------------
[42760.576146] WARNING: CPU: 2 PID: 1216 at kernel/smp.c:416 smp_call_function_many+0x88/0x20c
[42760.587839] Modules linked in:
[42760.593152] CPU: 2 PID: 1216 Comm: sh Not tainted 4.15.4-00373-gee058bb4d0c2 #2
[42760.603767] Stack : 8e09bd20 8e09bd20 8e09bd20 fffffff0 00000007 00000006 00000000 8e09bca8
[42760.616937] 95b2b379 95b2b379 807a0080 00000007 81944518 0000018a 00000032 00000000
[42760.630095] 00000000 00000030 80000000 00000000 806eca74 00000009 8017e2b8 000001a0
[42760.643169] 00000000 00000002 00000000 8e09baa4 00000008 808b8008 86d69080 8e09bca0
[42760.656282] 8e09ad50 805e20aa 00000000 00000000 00000000 8017e2b8 00000009 801070ca
[42760.669424] ...
[42760.673919] Call Trace:
[42760.678672] [<27fde568>] show_stack+0x70/0xf0
[42760.685417] [<84751641>] dump_stack+0xaa/0xd0
[42760.692188] [<699d671c>] __warn+0x80/0x92
[42760.698549] [<68915d41>] warn_slowpath_null+0x28/0x36
[42760.705912] [<f7c76c1c>] smp_call_function_many+0x88/0x20c
[42760.713696] [<6bbdfc2a>] arch_trigger_cpumask_backtrace+0x30/0x4a
[42760.722216] [<f845bd33>] rcu_dump_cpu_stacks+0x6a/0x98
[42760.729580] [<796e7629>] rcu_check_callbacks+0x672/0x6ac
[42760.737476] [<059b3b43>] update_process_times+0x18/0x34
[42760.744981] [<6eb94941>] tick_sched_handle.isra.5+0x26/0x38
[42760.752793] [<478d3d70>] tick_sched_timer+0x1c/0x50
[42760.759882] [<e56ea39f>] __hrtimer_run_queues+0xc6/0x226
[42760.767418] [<e88bbcae>] hrtimer_interrupt+0x88/0x19a
[42760.775031] [<6765a19e>] gic_compare_interrupt+0x2e/0x3a
[42760.782761] [<0558bf5f>] handle_percpu_devid_irq+0x78/0x168
[42760.790795] [<90c11ba2>] generic_handle_irq+0x1e/0x2c
[42760.798117] [<1b6d462c>] gic_handle_local_int+0x38/0x86
[42760.805545] [<b2ada1c7>] gic_irq_dispatch+0xa/0x14
[42760.812534] [<90c11ba2>] generic_handle_irq+0x1e/0x2c
[42760.820086] [<c7521934>] do_IRQ+0x16/0x20
[42760.826274] [<9aef3ce6>] plat_irq_dispatch+0x62/0x94
[42760.833458] [<6a94b53c>] except_vec_vi_end+0x70/0x78
[42760.840655] [<22284043>] smp_call_function_many+0x1ba/0x20c
[42760.848501] [<54022b58>] smp_call_function+0x1e/0x2c
[42760.855693] [<ab9fc705>] flush_tlb_mm+0x2a/0x98
[42760.862730] [<0844cdd0>] tlb_flush_mmu+0x1c/0x44
[42760.869628] [<cb259b74>] arch_tlb_finish_mmu+0x26/0x3e
[42760.877021] [<1aeaaf74>] tlb_finish_mmu+0x18/0x66
[42760.883907] [<b3fce717>] exit_mmap+0x76/0xea
[42760.890428] [<c4c8a2f6>] mmput+0x80/0x11a
[42760.896632] [<a41a08f4>] do_exit+0x1f4/0x80c
[42760.903158] [<ee01cef6>] do_group_exit+0x20/0x7e
[42760.909990] [<13fa8d54>] __wake_up_parent+0x0/0x1e
[42760.917045] [<46cf89d0>] smp_call_function_many+0x1a2/0x20c
[42760.924893] [<8c21a93b>] syscall_common+0x14/0x1c
[42760.931765] ---[ end trace 02aa09da9dc52a60 ]---
[42760.938342] ------------[ cut here ]------------
[42760.945311] WARNING: CPU: 2 PID: 1216 at kernel/smp.c:291 smp_call_function_single+0xee/0xf8
...
This patch switches MIPS' arch_trigger_cpumask_backtrace() to use async
IPIs & smp_call_function_single_async() in order to resolve this
problem. We ensure use of the pre-allocated call_single_data_t
structures is serialized by maintaining a cpumask indicating that
they're busy, and refusing to attempt to send an IPI when a CPU's bit is
set in this mask. This should only happen if a CPU hasn't responded to a
previous backtrace IPI - ie. if it's hung - and we print a warning to
the console in this case.
I've marked this for stable branches as far back as v4.9, to which it
applies cleanly. Strictly speaking the faulty MIPS implementation can be
traced further back to commit 856839b768 ("MIPS: Add
arch_trigger_all_cpu_backtrace() function") in v3.19, but kernel
versions v3.19 through v4.8 will require further work to backport due to
the rework performed in commit 9a01c3ed5c ("nmi_backtrace: add more
trigger_*_cpu_backtrace() methods").
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19597/
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org # v4.9+
Fixes: 856839b768 ("MIPS: Add arch_trigger_all_cpu_backtrace() function")
Fixes: 9a01c3ed5c ("nmi_backtrace: add more trigger_*_cpu_backtrace() methods")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5a267832c2 upstream.
The generic nmi_cpu_backtrace() function calls show_regs() when a struct
pt_regs is available, and dump_stack() otherwise. If we were to make use
of the generic nmi_cpu_backtrace() with MIPS' current implementation of
show_regs() this would mean that we see only register data with no
accompanying stack information, in contrast with our current
implementation which calls dump_stack() regardless of whether register
state is available.
In preparation for making use of the generic nmi_cpu_backtrace() to
implement arch_trigger_cpumask_backtrace(), have our implementation of
show_regs() call dump_stack() and drop the explicit dump_stack() call in
arch_dump_stack() which is invoked by arch_trigger_cpumask_backtrace().
This will allow the output we produce to remain the same after a later
patch switches to using nmi_cpu_backtrace(). It may mean that we produce
extra stack output in other uses of show_regs(), but this:
1) Seems harmless.
2) Is good for consistency between arch_trigger_cpumask_backtrace()
and other users of show_regs().
3) Matches the behaviour of the ARM & PowerPC architectures.
Marked for stable back to v4.9 as a prerequisite of the following patch
"MIPS: Call dump_stack() from show_regs()".
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19596/
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 58990d1ff3 upstream.
As commit 28e33f9d78 ("bpf: disallow arithmetic operations on
context pointer") already describes, f1174f77b5 ("bpf/verifier:
rework value tracking") removed the specific white-listed cases
we had previously where we would allow for pointer arithmetic in
order to further generalize it, and allow e.g. context access via
modified registers. While the dereferencing of modified context
pointers had been forbidden through 28e33f9d78, syzkaller did
recently manage to trigger several KASAN splats for slab out of
bounds access and use after frees by simply passing a modified
context pointer to a helper function which would then do the bad
access since verifier allowed it in adjust_ptr_min_max_vals().
Rejecting arithmetic on ctx pointer in adjust_ptr_min_max_vals()
generally could break existing programs as there's a valid use
case in tracing in combination with passing the ctx to helpers as
bpf_probe_read(), where the register then becomes unknown at
verification time due to adding a non-constant offset to it. An
access sequence may look like the following:
offset = args->filename; /* field __data_loc filename */
bpf_probe_read(&dst, len, (char *)args + offset); // args is ctx
There are two options: i) we could special case the ctx and as
soon as we add a constant or bounded offset to it (hence ctx type
wouldn't change) we could turn the ctx into an unknown scalar, or
ii) we generalize the sanity test for ctx member access into a
small helper and assert it on the ctx register that was passed
as a function argument. Fwiw, latter is more obvious and less
complex at the same time, and one case that may potentially be
legitimate in future for ctx member access at least would be for
ctx to carry a const offset. Therefore, fix follows approach
from ii) and adds test cases to BPF kselftests.
Fixes: f1174f77b5 ("bpf/verifier: rework value tracking")
Reported-by: syzbot+3d0b2441dbb71751615e@syzkaller.appspotmail.com
Reported-by: syzbot+c8504affd4fdd0c1b626@syzkaller.appspotmail.com
Reported-by: syzbot+e5190cb881d8660fb1a3@syzkaller.appspotmail.com
Reported-by: syzbot+efae31b384d5badbd620@syzkaller.appspotmail.com
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 28557cc106 upstream.
Revert commit c7f26ccfb2 ("mm/vmstat.c: fix vmstat_update() preemption
BUG"). Steven saw a "using smp_processor_id() in preemptible" message
and added a preempt_disable() section around it to keep it quiet. This
is not the right thing to do it does not fix the real problem.
vmstat_update() is invoked by a kworker on a specific CPU. This worker
it bound to this CPU. The name of the worker was "kworker/1:1" so it
should have been a worker which was bound to CPU1. A worker which can
run on any CPU would have a `u' before the first digit.
smp_processor_id() can be used in a preempt-enabled region as long as
the task is bound to a single CPU which is the case here. If it could
run on an arbitrary CPU then this is the problem we have an should seek
to resolve.
Not only this smp_processor_id() must not be migrated to another CPU but
also refresh_cpu_vm_stats() which might access wrong per-CPU variables.
Not to mention that other code relies on the fact that such a worker
runs on one specific CPU only.
Therefore revert that commit and we should look instead what broke the
affinity mask of the kworker.
Link: http://lkml.kernel.org/r/20180504104451.20278-1-bigeasy@linutronix.de
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Steven J. Hill <steven.hill@cavium.com>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce00bf07cc upstream.
The old code would indefinitely block other users of nf_log_mutex if
a userspace access in proc_dostring() blocked e.g. due to a userfaultfd
region. Fix it by moving proc_dostring() out of the locked region.
This is a followup to commit 266d07cb1c ("netfilter: nf_log: fix
sleeping function called from invalid context"), which changed this code
from using rcu_read_lock() to taking nf_log_mutex.
Fixes: 266d07cb1c ("netfilter: nf_log: fix sleeping function calle[...]")
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dbc626597c upstream.
Currently device_supports_dax() just checks to see if the QUEUE_FLAG_DAX
flag is set on the device's request queue to decide whether or not the
device supports filesystem DAX. Really we should be using
bdev_dax_supported() like filesystems do at mount time. This performs
other tests like checking to make sure the dax_direct_access() path works.
We also explicitly clear QUEUE_FLAG_DAX on the DM device's request queue if
any of the underlying devices do not support DAX. This makes the handling
of QUEUE_FLAG_DAX consistent with the setting/clearing of most other flags
in dm_table_set_restrictions().
Now that bdev_dax_supported() explicitly checks for QUEUE_FLAG_DAX, this
will ensure that filesystems built upon DM devices will only be able to
mount with DAX if all underlying devices also support DAX.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Fixes: commit 545ed20e6d ("dm: add infrastructure for DAX support")
Cc: stable@vger.kernel.org
Acked-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 15256f6cc4 upstream.
Add an explicit check for QUEUE_FLAG_DAX to __bdev_dax_supported(). This
is needed for DM configurations where the first element in the dm-linear or
dm-stripe target supports DAX, but other elements do not. Without this
check __bdev_dax_supported() will pass for such devices, letting a
filesystem on that device mount with the DAX option.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Suggested-by: Mike Snitzer <snitzer@redhat.com>
Fixes: commit 545ed20e6d ("dm: add infrastructure for DAX support")
Cc: stable@vger.kernel.org
Acked-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 80660f2025 upstream.
The function return values are confusing with the way the function is
named. We expect a true or false return value but it actually returns
0/-errno. This makes the code very confusing. Changing the return values
to return a bool where if DAX is supported then return true and no DAX
support returns false.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ba23cba9b3 upstream.
Change bdev_dax_supported so it takes a bdev parameter. This enables
multi-device filesystems like xfs to check that a dax device can work for
the particular filesystem. Once that's in place, actually fix all the
parts of XFS where we need to be able to distinguish between datadev and
rtdev.
This patch fixes the problem where we screw up the dax support checking
in xfs if the datadev and rtdev have different dax capabilities.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
[rez: Re-added __bdev_dax_supported() for !CONFIG_FS_DAX cases]
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9aa613674f upstream.
If DMA safe memory was allocated, but the subsequent I2C transfer
fails the memory is leaked. Plug this leak.
Fixes: 8a77821e74 ("i2c: smbus: use DMA safe buffers for emulated SMBus transactions")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e03477cb7 upstream.
In i2c_smbus_xfer_emulated(), the function i2c_transfer() is invoked to
transfer i2c messages. The number of actual transferred messages is
returned and saved to 'status'. If 'status' is negative, that means an
error occurred during the transfer process. In that case, the value of
'status' is an error code to indicate the reason of the transfer failure.
In most cases, i2c_transfer() can transfer 'num' messages with no error.
And so 'status' == 'num'. However, due to unexpected errors, it is probable
that only partial messages are transferred by i2c_transfer(). As a result,
'status' != 'num'. This special case is not checked after the invocation of
i2c_transfer() and can potentially lead to unexpected issues in the
following execution since it is expected that 'status' == 'num'.
This patch checks the return value of i2c_transfer() and returns an error
code -EIO if the number of actual transferred messages 'status' is not
equal to 'num'.
Signed-off-by: Wenwen Wang <wang6495@umn.edu>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f732850df upstream.
Detected on the Dell XPS 9365.
The laptop has 2 devices that benefit from the hid-generic auto-unbinding.
When those 2 devices are presented to the userspace, udev loads both wacom and
hid-multitouch. When this happens, the code in __hid_bus_reprobe_drivers() is
called concurrently and the second device gets reprobed twice.
An other bug in the power_supply subsystem prevent to remove the wacom driver
if it just finished its initialization, which basically kills the wacom node.
[jkosina@suse.cz: reformat changelog a bit]
Fixes c17a7476e4 ("HID: core: rewrite the hid-generic automatic unbind")
Cc: stable@vger.kernel.org # v4.17
Tested-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f65245f2d upstream.
uref->field_index, uref->usage_index, finfo.field_index and cinfo.index can be
indirectly controlled by user-space, hence leading to a potential exploitation
of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/hid/usbhid/hiddev.c:473 hiddev_ioctl_usage() warn: potential spectre issue 'report->field' (local cap)
drivers/hid/usbhid/hiddev.c:477 hiddev_ioctl_usage() warn: potential spectre issue 'field->usage' (local cap)
drivers/hid/usbhid/hiddev.c:757 hiddev_ioctl() warn: potential spectre issue 'report->field' (local cap)
drivers/hid/usbhid/hiddev.c:801 hiddev_ioctl() warn: potential spectre issue 'hid->collection' (local cap)
Fix this by sanitizing such structure fields before using them to index
report->field, field->usage and hid->collection
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef6eaf2727 upstream.
Commit ac75a04104 ("HID: i2c-hid: fix size check and type usage") started
writing messages when the ret_size is <= 2 from i2c_master_recv. However, my
device i2c-DLL07D1 returns 2 for a short period of time (~0.5s) after I stop
moving the pointing stick or touchpad. It varies, but you get ~50 messages
each time which spams the log hard.
[ 95.925055] i2c_hid i2c-DLL07D1:01: i2c_hid_get_input: incomplete report (83/2)
This has also been observed with a i2c-ALP0017.
[ 1781.266353] i2c_hid i2c-ALP0017:00: i2c_hid_get_input: incomplete report (30/2)
Only print the message when ret_size is totally invalid and less than 2 to cut
down on the log spam.
Fixes: ac75a04104 ("HID: i2c-hid: fix size check and type usage")
Reported-by: John Smith <john-s-84@gmx.net>
Cc: stable@vger.kernel.org
Signed-off-by: Jason Andryuk <jandryuk@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a17712c8e4 upstream.
This patch attempts to close a hole leading to a BUG seen with hot
removals during writes [1].
A block device (NVME namespace in this test case) is formatted to EXT4
without partitions. It's mounted and write I/O is run to a file, then
the device is hot removed from the slot. The superblock attempts to be
written to the drive which is no longer present.
The typical chain of events leading to the BUG:
ext4_commit_super()
__sync_dirty_buffer()
submit_bh()
submit_bh_wbc()
BUG_ON(!buffer_mapped(bh));
This fix checks for the superblock's buffer head being mapped prior to
syncing.
[1] https://www.spinics.net/lists/linux-ext4/msg56527.html
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bfe0a5f47a upstream.
The kernel's ext4 mount-time checks were more permissive than
e2fsprogs's libext2fs checks when opening a file system. The
superblock is considered too insane for debugfs or e2fsck to operate
on it, the kernel has no business trying to mount it.
This will make file system fuzzing tools work harder, but the failure
cases that they find will be more useful and be easier to evaluate.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c37e9e0134 upstream.
If there is a directory entry pointing to a system inode (such as a
journal inode), complain and declare the file system to be corrupted.
Also, if the superblock's first inode number field is too small,
refuse to mount the file system.
This addresses CVE-2018-10882.
https://bugzilla.kernel.org/show_bug.cgi?id=200069
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8cdb5240ec upstream.
When expanding the extra isize space, we must never move the
system.data xattr out of the inode body. For performance reasons, it
doesn't make any sense, and the inline data implementation assumes
that system.data xattr is never in the external xattr block.
This addresses CVE-2018-10880
https://bugzilla.kernel.org/show_bug.cgi?id=200005
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e8ab72a81 upstream.
When converting from an inode from storing the data in-line to a data
block, ext4_destroy_inline_data_nolock() was only clearing the on-disk
copy of the i_blocks[] array. It was not clearing copy of the
i_blocks[] in ext4_inode_info, in i_data[], which is the copy actually
used by ext4_map_blocks().
This didn't matter much if we are using extents, since the extents
header would be invalid and thus the extents could would re-initialize
the extents tree. But if we are using indirect blocks, the previous
contents of the i_blocks array will be treated as block numbers, with
potentially catastrophic results to the file system integrity and/or
user data.
This gets worse if the file system is using a 1k block size and
s_first_data is zero, but even without this, the file system can get
quite badly corrupted.
This addresses CVE-2018-10881.
https://bugzilla.kernel.org/show_bug.cgi?id=200015
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8844618d8a upstream.
The bg_flags field in the block group descripts is only valid if the
uninit_bg or metadata_csum feature is enabled. We were not
consistently looking at this field; fix this.
Also block group #0 must never have uninitialized allocation bitmaps,
or need to be zeroed, since that's where the root inode, and other
special inodes are set up. Check for these conditions and mark the
file system as corrupted if they are detected.
This addresses CVE-2018-10876.
https://bugzilla.kernel.org/show_bug.cgi?id=199403
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 513f86d738 upstream.
If there an inode points to a block which is also some other type of
metadata block (such as a block allocation bitmap), the
buffer_verified flag can be set when it was validated as that other
metadata block type; however, it would make a really terrible external
attribute block. The reason why we use the verified flag is to avoid
constantly reverifying the block. However, it doesn't take much
overhead to make sure the magic number of the xattr block is correct,
and this will avoid potential crashes.
This addresses CVE-2018-10879.
https://bugzilla.kernel.org/show_bug.cgi?id=200001
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e09463f220 upstream.
Do not set the b_modified flag in block's journal head should not
until after we're sure that jbd2_journal_dirty_metadat() will not
abort with an error due to there not being enough space reserved in
the jbd2 handle.
Otherwise, future attempts to modify the buffer may lead a large
number of spurious errors and warnings.
This addresses CVE-2018-10883.
https://bugzilla.kernel.org/show_bug.cgi?id=200071
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9ff68521a upstream.
The other day I was testing one of the HP laptops at my office with an
i915/amdgpu hybrid setup and noticed that hotplugging was non-functional
on almost all of the display outputs. I eventually discovered that all
of the external outputs were connected to the amdgpu device instead of
i915, and that the hotplugs weren't being detected so long as the GPU
was in runtime suspend. After some talking with folks at AMD, I learned
that amdgpu is actually supposed to support hotplug detection in runtime
suspend so long as the OEM has implemented it properly in the firmware.
On this HP ZBook 15 G4 (the machine in question), amdgpu wasn't managing
to find the ATIF handle at all despite the fact that I could see acpi
events being sent in response to any hotplugging. After going through
dumps of the firmware, I discovered that this machine did in fact
support ATIF, but that it's ATIF method lived in an entirely different
namespace than this device's handle (the device handle was
\_SB_.PCI0.PEG0.PEGP, but ATIF lives in ATPX's handle at
\_SB_.PCI0.GFX0).
So, fix this by probing ATPX's ACPI parent's namespace if we can't find
ATIF elsewhere, along with storing a pointer to the proper handle to use
for ATIF and using that instead of the device's handle.
This fixes HPD detection while in runtime suspend for this ZBook!
v2: Update the comment to reflect how the namespaces are arranged
based on the system configuration. (Alex)
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4aa5d5eb82 upstream.
Since it seems that some vendors are storing the ATIF ACPI methods under
the same handle that ATPX lives under instead of the device's own
handle, we're going to need to be able to retrieve this handle later so
we can probe for ATIF there.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 99ec9e7751 upstream.
The displaylink hardware has such a peculiarity that it doesn't render a
command until next command is received. This produces occasional
corruption, such as when setting 22x11 font on the console, only the first
line of the cursor will be blinking if the cursor is located at some
specific columns.
When we end up with a repeating pixel, the driver has a bug that it leaves
one uninitialized byte after the command (and this byte is enough to flush
the command and render it - thus it fixes the screen corruption), however
whe we end up with a non-repeating pixel, there is no byte appended and
this results in temporary screen corruption.
This patch fixes the screen corruption by always appending a byte 0xAF at
the end of URB. It also removes the uninitialized byte.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ffbe65578 upstream.
For every request we send, whether it is SMB1 or SMB2+, we attempt to
reconnect tcon (cifs_reconnect_tcon or smb2_reconnect) before carrying
out the request.
So, while server->tcpStatus != CifsNeedReconnect, we wait for the
reconnection to succeed on wait_event_interruptible_timeout(). If it
returns, that means that either the condition was evaluated to true, or
timeout elapsed, or it was interrupted by a signal.
Since we're not handling the case where the process woke up due to a
received signal (-ERESTARTSYS), the next call to
wait_event_interruptible_timeout() will _always_ fail and we end up
looping forever inside either cifs_reconnect_tcon() or smb2_reconnect().
Here's an example of how to trigger that:
$ mount.cifs //foo/share /mnt/test -o
username=foo,password=foo,vers=1.0,hard
(break connection to server before executing bellow cmd)
$ stat -f /mnt/test & sleep 140
[1] 2511
$ ps -aux -q 2511
USER PID %CPU %MEM VSZ RSS TTY STAT START TIME COMMAND
root 2511 0.0 0.0 12892 1008 pts/0 S 12:24 0:00 stat -f
/mnt/test
$ kill -9 2511
(wait for a while; process is stuck in the kernel)
$ ps -aux -q 2511
USER PID %CPU %MEM VSZ RSS TTY STAT START TIME COMMAND
root 2511 83.2 0.0 12892 1008 pts/0 R 12:24 30:01 stat -f
/mnt/test
By using 'hard' mount point means that cifs.ko will keep retrying
indefinitely, however we must allow the process to be killed otherwise
it would hang the system.
Signed-off-by: Paulo Alcantara <palcantara@suse.de>
Cc: stable@vger.kernel.org
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 696e420bb2 upstream.
With protocol version 2.0 mounts we have seen crashes with corrupt mid
entries. Either the server->pending_mid_q list becomes corrupt with a
cyclic reference in one element or a mid object fetched by the
demultiplexer thread becomes overwritten during use.
Code review identified a race between the demultiplexer thread and the
request issuing thread. The demultiplexer thread seems to be written
with the assumption that it is the sole user of the mid object until
it calls the mid callback which either wakes the issuer task or
deletes the mid.
This assumption is not true because the issuer task can be woken up
earlier by a signal. If the demultiplexer thread has proceeded as far
as setting the mid_state to MID_RESPONSE_RECEIVED then the issuer
thread will happily end up calling cifs_delete_mid while the
demultiplexer thread still is using the mid object.
Inserting a delay in the cifs demultiplexer thread widens the race
window and makes reproduction of the race very easy:
if (server->large_buf)
buf = server->bigbuf;
+ usleep_range(500, 4000);
server->lstrp = jiffies;
To resolve this I think the proper solution involves putting a
reference count on the mid object. This patch makes sure that the
demultiplexer thread holds a reference until it has finished
processing the transaction.
Cc: stable@vger.kernel.org
Signed-off-by: Lars Persson <larper@axis.com>
Acked-by: Paulo Alcantara <palcantara@suse.de>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07eaa43e66 upstream.
Disable the metastability workaround for USB2. The original
patch disabled the workaround on the wrong USB port.
Fixes: b8c9c6fa20 ("ARM: dts: dra7: Disable USB metastability workaround for USB2")
Cc: <stable@vger.kernel.org> [4.16+]
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0144eb204c upstream.
A previous patch removed OMAP clock aliases that were perceived
to be unnecessary. Unfortunately, it broke the ethernet on the
am3517-evm. This patch enables the MDIO clock and EMAC clock.
Fixes: 0ed266d7ae ("clk: ti: omap3: cleanup unnecessary clock aliases")
Cc: stable@vger.kernel.org #4.16+
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 06d793b114 upstream.
The pinctrl settings were incorrect for the touchscreen interrupt line, causing
an interrupt storm. This change has been tested with both the atmel_mxt_ts and
RMI4 drivers on the RDU1 units.
The value 0x4 comes from the value of register IOMUXC_SW_PAD_CTL_PAD_CSI1_D8
from the old vendor kernel.
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Fixes: ceef0396f3 ("ARM: dts: imx: add ZII RDU1 board")
Cc: <stable@vger.kernel.org> # 4.15+
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb94b55af3 upstream.
The patch noted in the fixes below converted get_user_pages_fast() to
get_user_pages_longterm(), however the two calls differ in a few ways.
First _fast() is documented to not require the mmap_sem, while _longterm()
is documented to need it. Hold the mmap sem as required.
Second, _fast accepts an 'int write' while _longterm uses 'unsigned int
gup_flags', so the expression '!!(prot & IOMMU_WRITE)' is only working by
luck as FOLL_WRITE is currently == 0x1. Use the expected FOLL_WRITE
constant instead.
Fixes: 94db151dc8 ("vfio: disable filesystem-dax page pinning")
Cc: <stable@vger.kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 64dafbc953 upstream.
We have
struct drbd_requests { ... struct bio *private_bio; ... }
to hold a bio clone for local submission.
On local IO completion, we put that bio, and in case we want to use the
result later, we overload that member to hold the ERR_PTR() of the
completion result,
Which, before v4.3, used to be the passed in "int error",
so we could first bio_put(), then assign.
v4.3-rc1~100^2~21 4246a0b63b block: add a bi_error field to struct bio
changed that:
bio_put(req->private_bio);
- req->private_bio = ERR_PTR(error);
+ req->private_bio = ERR_PTR(bio->bi_error);
Which introduces an access after free,
because it was non obvious that req->private_bio == bio.
Impact of that was mostly unnoticable, because we only use that value
in a multiple-failure case, and even then map any "unexpected" error
code to EIO, so worst case we could potentially mask a more specific
error with EIO in a multiple failure case.
Unless the pointed to memory region was unmapped, as is the case with
CONFIG_DEBUG_PAGEALLOC, in which case this results in
BUG: unable to handle kernel paging request
v4.13-rc1~70^2~75 4e4cbee93d block: switch bios to blk_status_t
changes it further to
bio_put(req->private_bio);
req->private_bio = ERR_PTR(blk_status_to_errno(bio->bi_status));
And blk_status_to_errno() now contains a WARN_ON_ONCE() for unexpected
values, which catches this "sometimes", if the memory has been reused
quickly enough for other things.
Should also go into stable since 4.3, with the trivial change around 4.13.
Cc: stable@vger.kernel.org
Fixes: 4246a0b63b block: add a bi_error field to struct bio
Reported-by: Sarah Newman <srn@prgmr.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 891f6a726c upstream.
In the critical section cleanup we must not mess with r1. For march=z9
or older, larl + ex (instead of exrl) are used with r1 as a temporary
register. This can clobber r1 in several interrupt handlers. Fix this by
using r11 as a temp register. r11 is being saved by all callers of
cleanup_critical.
Fixes: 6dd85fbb87 ("s390: move expoline assembler macros to a header")
Cc: stable@vger.kernel.org #v4.16
Reported-by: Oliver Kurz <okurz@suse.com>
Reported-by: Petr Tesařík <ptesarik@suse.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 63ce3c384d upstream.
SPC5r17 states that the contents of the ADDITIONAL LENGTH field are not
altered based on the allocation length, so always calculate and pack the
full key list length even if the list itself is truncated.
According to Maged:
Yes it fixes the "Storage Spaces Persistent Reservation" test in the
Windows 2016 Server Failover Cluster validation suites when having
many connections that result in more than 8 registrations. I tested
your patch on 4.17 with iblock.
This behaviour can be tested using the libiscsi PrinReadKeys.Truncate test.
Cc: stable@vger.kernel.org
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Tested-by: Maged Mokhtar <mmokhtar@petasan.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 59b433c825 upstream.
The driver fails to set the correct queue depth for native devices, due to
failing to set the device type prior to calling aac_set_safw_target_qd().
This results in slave configure setting the queue depth to 1.
This causes around 30% performance degradation. Fixed by setting the dev
type before trying to set queue depth.
Reported-by: Steve Best <sbest@redhat.com>
Fixes: 0bcb45fb20 ("scsi: aacraid: Add helper function to set queue depth")
cc: stable@vger.kernel.org
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <David.Carroll@microsemi.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26b5b874af upstream.
As Al Viro noted in commit 128394eff3 ("sg_write()/bsg_write() is not fit
to be called under KERNEL_DS"), sg improperly accesses userspace memory
outside the provided buffer, permitting kernel memory corruption via
splice(). But it doesn't just do it on ->write(), also on ->read().
As a band-aid, make sure that the ->read() and ->write() handlers can not
be called in weird contexts (kernel context or credentials different from
file opener), like for ib_safe_file_access().
If someone needs to use these interfaces from different security contexts,
a new interface should be written that goes through the ->ioctl() handler.
I've mostly copypasted ib_safe_file_access() over as sg_safe_file_access()
because I couldn't find a good common header - please tell me if you know a
better way.
[mkp: s/_safe_/_check_/]
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: <stable@vger.kernel.org>
Signed-off-by: Jann Horn <jannh@google.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cf4d418e65 upstream.
'err' is used as a NUL-terminated string, but using strncpy() with the length
equal to the buffer size may result in lack of the termination:
kernel/trace/trace_events_hist.c: In function 'hist_err_event':
kernel/trace/trace_events_hist.c:396:3: error: 'strncpy' specified bound 256 equals destination size [-Werror=stringop-truncation]
strncpy(err, var, MAX_FILTER_STR_VAL);
This changes it to use the safer strscpy() instead.
Link: http://lkml.kernel.org/r/20180328140920.2842153-1-arnd@arndb.de
Cc: stable@vger.kernel.org
Fixes: f404da6e1d ("tracing: Add 'last error' error facility for hist triggers")
Acked-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2cd5fe22d9 upstream.
Currently, there is nothing in amdgpu that actually uses these structs
other than amdgpu_acpi.c. Additionally, since we're about to start
saving the correct ACPI handle to use for calling ATIF in this struct
this saves us from having to handle making sure that the acpi_handle
(and by proxy, the type definition for acpi_handle and all of the other
acpi headers) doesn't need to be included within the amdgpu_drv struct
itself. This follows the example set by amdgpu_atpx_handler.c.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 673b427166 upstream.
A hooking API was implemented for 4.17 in fa93854f7a followed
by hooks for Thinkpad laptops in 2801b9683f. The Thinkpad
drivers did not support the Thinkpad 13 and the hooking API crashes
on unsupported batteries by altering a list of hooks during unsafe
iteration. Thus, Thinkpad 13 laptops could no longer boot.
Additionally, a lock was kept in place and debugging information was
printed out of order.
Fixes: fa93854f7a (battery: Add the battery hooking API)
Cc: 4.17+ <stable@vger.kernel.org> # 4.17+
Signed-off-by: Jouke Witteveen <j.witteveen@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a0d5f3b69a upstream.
Commit 5088814a6e (ACPICA: AML parser: attempt to continue loading
table after error) unintentionally added leading newlines to error
messages emitted by ACPICA which caused unexpected things to be
printed to the kernel log. Drop these newlines (which effectively
reverts the part of commit 5088814a6e adding them).
Fixes: 5088814a6e (ACPICA: AML parser: attempt to continue loading table after error)
Reported-by: Toralf Förster <toralf.foerster@gmx.de>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Cc: 4.17+ <stable@vger.kernel.org> # 4.17+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26112ddc25 upstream.
It is reported that commit c62ec4610c (PM / core: Fix direct_complete
handling for devices with no callbacks) introduced a system suspend
regression on Samsung 305V4A by allowing a PCI bridge (not a PCIe
port) to stay in D3 over suspend-to-RAM, which is a side effect of
setting power.direct_complete for the children of that bridge that
have no PM callbacks.
On the majority of systems PCI bridges are not allowed to be
runtime-suspended (the power/control sysfs attribute is set to "on"
for them by default), but user space can change that setting and if
it does so and a given bridge has no children with PM callbacks, the
direct_complete optimization will be applied to it and it will stay
in suspend over system suspend. Apparently, that confuses the
platform firmware on the affected machine and that may very well
happen elsewhere, so avoid the direct_complete optimization for
PCI bridges with no drivers (if there is a driver, it should take
care of the PM handling) on suspend-to-RAM altogether (that should
not matter for suspend-to-idle as platform firmware is not involved
in it).
Fixes: c62ec4610c (PM / core: Fix direct_complete handling for devices with no callbacks)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199941
Reported-by: n0000b.n000b@gmail.com
Tested-by: n0000b.n000b@gmail.com
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: 4.15+ <stable@vger.kernel.org> # 4.15+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df07101e1c upstream.
According to the reference manual the shp_2_mcu / mcu_2_shp
scripts must be used for devices connected through the SPBA.
This fixes an issue we saw with DMA transfers.
Sometimes the SPI controller RX FIFO was not empty after a DMA
transfer and the driver got stuck in the next PIO transfer when
it read one word more than expected.
commit dd4b487b32 ("ARM: dts: imx6: Use correct SDMA script
for SPI cores") is fixing the same issue but only for SPI1 - 4.
Fixes: 677940258d ("ARM: dts: imx6q: enable dma for ecspi5")
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit adc972c5b8 upstream.
When depth of chain is bigger than NFT_JUMP_STACK_SIZE, the nft_do_chain
crashes. But there is no need to crash hard here.
Suggested-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc6ddbecce upstream.
This needs to use xt_unregister_targets, else new revision is left
on the list which then causes list to point to a target struct that has been free'd.
Fixes: 472a73e007 ("netfilter: xt_conntrack: Support bit-shifting for CONNMARK & MARK targets.")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cede24d1b2 upstream.
In commit 47b7e7f828, this bit was removed at the same time the
RT6_LOOKUP_F_IFACE flag was removed. However, it is needed when
link-local addresses are used, which is a very common case: when
packets are routed, neighbor solicitations are done using link-local
addresses. For example, the following neighbor solicitation is not
matched by "-m rpfilter":
IP6 fe80::5254:33ff:fe00:1 > ff02::1:ff00:3: ICMP6, neighbor
solicitation, who has 2001:db8::5254:33ff:fe00:3, length 32
Commit 47b7e7f828 doesn't quite explain why we shouldn't use
RT6_LOOKUP_F_IFACE in the rpfilter case. I suppose the interface check
later in the function would make it redundant. However, the remaining
of the routing code is using RT6_LOOKUP_F_IFACE when there is no
source address (which matches rpfilter's case with a non-unicast
destination, like with neighbor solicitation).
Signed-off-by: Vincent Bernat <vincent@bernat.im>
Fixes: 47b7e7f828 ("netfilter: don't set F_IFACE on ipv6 fib lookups")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4dccc4d517 upstream.
While Bspec doesn't list a specific sequence for turning off the DP port
on g4x we are getting an underrun if the port is disabled in the
.disable() hook. Looks like the pipe stops when the port stops, and by
that time the plane disable may not have completed yet. Also the plane(s)
seem to end up in some wonky state when this happens as they also signal
another underrun immediately after we turn them back on during the next
enable sequence.
We could add a vblank wait in .disable() to avoid wedging the planes,
but I assume we're still tripping up the pipe in some way. So it seems
better to me to just follow the ILK+ sequence and turn off the DP port
in .post_disable() instead. This sequence doesn't seem to suffer from
this problem. Could be it was always the intended sequence for DP and
the gen4 bspec was just never updated to include it.
Originally we used the bad sequence even on ilk+, but I changed that
in commit 08aff3fe26 ("drm/i915: Move DP port disable to post_disable
for pch platforms") as it was causing issues on those platforms as well.
I left out g4x then only because I didn't have the hardware to test it.
Now that I do it's fairly clear that the ilk+ sequence is also the
right choice for g4x.
v2: Fix whitespace fail (Jani)
Mention the ilk+ commit (Jani)
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180613160553.11664-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit 51a9f6dfc0)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4dc055c9cc upstream.
On i965/g4x IIR is edge triggered. So in order for IIR to notice that
there is still a pending interrupt we have to force and edge in ISR.
For the ISR/IIR pipe event bits we can do that by temporarily
clearing all the PIPESTAT enable bits when we ack the status bits.
This will force the ISR pipe event bit low, and it can then go back
high when we restore the PIPESTAT enable bits.
This avoids the following race:
1. stat = read(PIPESTAT)
2. an enabled PIPESTAT status bit goes high
3. write(PIPESTAT, enable|stat);
4. write(IIR, PIPE_EVENT)
The end result is IIR==0 and ISR!=0. This can lead to nasty
vblank wait/flip_done timeouts if another interrupt source
doesn't trick us into looking at the PIPESTAT status bits despite
the IIR PIPE_EVENT bit being low.
Before i965 IIR was level triggered so this problem can't actually
happen there. And curiously VLV/CHV went back to the level triggered
scheme as well. But for simplicity we'll use the same i965/g4x
compatible code for all platforms.
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106033
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105225
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106030
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180611200258.27121-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit 132c27c97c)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4de9f38bb2 upstream.
Currently, amdgpu_do_flip() spinlocks crtc->dev->event_lock and
releases it only after committing updates to the stream.
dc_commit_updates_for_stream() should be moved out of
spinlock for the below reasons:
1. event_lock is supposed to protect access to acrct->pflip_status _only_
2. dc_commit_updates_for_stream() has potential sleep's
and also its not appropriate to be in an atomic state
for such long sequences of code.
Signed-off-by: Shirish S <shirish.s@amd.com>
Suggested-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe2a196529 upstream.
This fixes a regression I accidentally reduced that was picked up by
kasan, where we were checking the CRTC atomic states after DRM's helpers
had already freed them. Example:
==================================================================
BUG: KASAN: use-after-free in amdgpu_dm_atomic_commit_tail.cold.50+0x13d/0x15a [amdgpu]
Read of size 1 at addr ffff8803a697b071 by task kworker/u16:0/7
CPU: 7 PID: 7 Comm: kworker/u16:0 Tainted: G O 4.18.0-rc1Lyude-Upstream+ #1
Hardware name: HP HP ZBook 15 G4/8275, BIOS P70 Ver. 01.21 05/02/2018
Workqueue: events_unbound commit_work [drm_kms_helper]
Call Trace:
dump_stack+0xc1/0x169
? dump_stack_print_info.cold.1+0x42/0x42
? kmsg_dump_rewind_nolock+0xd9/0xd9
? printk+0x9f/0xc5
? amdgpu_dm_atomic_commit_tail.cold.50+0x13d/0x15a [amdgpu]
print_address_description+0x6c/0x23c
? amdgpu_dm_atomic_commit_tail.cold.50+0x13d/0x15a [amdgpu]
kasan_report.cold.6+0x241/0x2fd
amdgpu_dm_atomic_commit_tail.cold.50+0x13d/0x15a [amdgpu]
? commit_planes_to_stream.constprop.45+0x13b0/0x13b0 [amdgpu]
? cpu_load_update_active+0x290/0x290
? finish_task_switch+0x2bd/0x840
? __switch_to_asm+0x34/0x70
? read_word_at_a_time+0xe/0x20
? strscpy+0x14b/0x460
? drm_atomic_helper_wait_for_dependencies+0x47d/0x7e0 [drm_kms_helper]
commit_tail+0x96/0xe0 [drm_kms_helper]
process_one_work+0x88a/0x1360
? create_worker+0x540/0x540
? __sched_text_start+0x8/0x8
? move_queued_task+0x760/0x760
? call_rcu_sched+0x20/0x20
? vsnprintf+0xcda/0x1350
? wait_woken+0x1c0/0x1c0
? mutex_unlock+0x1d/0x40
? init_timer_key+0x190/0x230
? schedule+0xea/0x390
? __schedule+0x1ea0/0x1ea0
? need_to_create_worker+0xe4/0x210
? init_worker_pool+0x700/0x700
? try_to_del_timer_sync+0xbf/0x110
? del_timer+0x120/0x120
? __mutex_lock_slowpath+0x10/0x10
worker_thread+0x196/0x11f0
? flush_rcu_work+0x50/0x50
? __switch_to_asm+0x34/0x70
? __switch_to_asm+0x34/0x70
? __switch_to_asm+0x40/0x70
? __switch_to_asm+0x34/0x70
? __switch_to_asm+0x40/0x70
? __switch_to_asm+0x34/0x70
? __switch_to_asm+0x40/0x70
? __schedule+0x7d6/0x1ea0
? migrate_swap_stop+0x850/0x880
? __sched_text_start+0x8/0x8
? save_stack+0x8c/0xb0
? kasan_kmalloc+0xbf/0xe0
? kmem_cache_alloc_trace+0xe4/0x190
? kthread+0x98/0x390
? ret_from_fork+0x35/0x40
? ret_from_fork+0x35/0x40
? deactivate_slab.isra.67+0x3c4/0x5c0
? kthread+0x98/0x390
? kthread+0x98/0x390
? set_track+0x76/0x120
? schedule+0xea/0x390
? __schedule+0x1ea0/0x1ea0
? wait_woken+0x1c0/0x1c0
? kasan_unpoison_shadow+0x30/0x40
? parse_args.cold.15+0x17a/0x17a
? flush_rcu_work+0x50/0x50
kthread+0x2d4/0x390
? kthread_create_worker_on_cpu+0xc0/0xc0
ret_from_fork+0x35/0x40
Allocated by task 1124:
kasan_kmalloc+0xbf/0xe0
kmem_cache_alloc_trace+0xe4/0x190
dm_crtc_duplicate_state+0x78/0x130 [amdgpu]
drm_atomic_get_crtc_state+0x147/0x410 [drm]
page_flip_common+0x57/0x230 [drm_kms_helper]
drm_atomic_helper_page_flip+0xa6/0x110 [drm_kms_helper]
drm_mode_page_flip_ioctl+0xc4b/0x10a0 [drm]
drm_ioctl_kernel+0x1d4/0x260 [drm]
drm_ioctl+0x433/0x920 [drm]
amdgpu_drm_ioctl+0x11d/0x290 [amdgpu]
do_vfs_ioctl+0x1a1/0x13d0
ksys_ioctl+0x60/0x90
__x64_sys_ioctl+0x6f/0xb0
do_syscall_64+0x147/0x440
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Freed by task 1124:
__kasan_slab_free+0x12e/0x180
kfree+0x92/0x1a0
drm_atomic_state_default_clear+0x315/0xc40 [drm]
__drm_atomic_state_free+0x35/0xd0 [drm]
drm_atomic_helper_update_plane+0xac/0x350 [drm_kms_helper]
__setplane_internal+0x2d6/0x840 [drm]
drm_mode_cursor_universal+0x41e/0xbe0 [drm]
drm_mode_cursor_common+0x49f/0x880 [drm]
drm_mode_cursor_ioctl+0xd8/0x130 [drm]
drm_ioctl_kernel+0x1d4/0x260 [drm]
drm_ioctl+0x433/0x920 [drm]
amdgpu_drm_ioctl+0x11d/0x290 [amdgpu]
do_vfs_ioctl+0x1a1/0x13d0
ksys_ioctl+0x60/0x90
__x64_sys_ioctl+0x6f/0xb0
do_syscall_64+0x147/0x440
entry_SYSCALL_64_after_hwframe+0x44/0xa9
The buggy address belongs to the object at ffff8803a697b068
which belongs to the cache kmalloc-1024 of size 1024
The buggy address is located 9 bytes inside of
1024-byte region [ffff8803a697b068, ffff8803a697b468)
The buggy address belongs to the page:
page:ffffea000e9a5e00 count:1 mapcount:0 mapping:ffff88041e00efc0 index:0x0 compound_mapcount: 0
flags: 0x8000000000008100(slab|head)
raw: 8000000000008100 ffffea000ecbc208 ffff88041e000c70 ffff88041e00efc0
raw: 0000000000000000 0000000000170017 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff8803a697af00: fb fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff8803a697af80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff8803a697b000: fc fc fc fc fc fc fc fc fc fc fc fc fc fb fb fb
^
ffff8803a697b080: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff8803a697b100: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
==================================================================
So, we fix this by counting the number of CRTCs this atomic commit disabled
early on in the function before their atomic states have been freed, then use
that count later to do the appropriate number of RPM puts at the end of the
function.
Acked-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Cc: stable@vger.kernel.org
Fixes: 97028037a3 ("drm/amdgpu: Grab/put runtime PM references in atomic_commit_tail()")
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Michel Dänzer <michel@daenzer.net>
Reported-by: Michel Dänzer <michel@daenzer.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7303b39e46 upstream.
Even BOs with AMDGPU_GEM_CREATE_NO_CPU_ACCESS may end up at least
partially in CPU visible VRAM, in particular when all VRAM is visible.
v2:
* Don't take VRAM mgr spinlock, not needed (Christian König)
* Make loop logic simpler and clearer.
Cc: stable@vger.kernel.org
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d9fda24804 upstream.
We've had a number of users report failures to detect and light up
display with DC with LVDS and VGA. These connector types are not
currently supported with DC. I'd like to add support but unfortunately
don't have a system with LVDS or VGA available.
In order not to cause regressions we should probably fallback to the
non-DC driver for ASICs that support VGA and LVDS.
These ASICs are:
* Bonaire
* Kabini
* Kaveri
* Mullins
ASIC support can always be force enabled with amdgpu.dc=1
v2: Keep Hawaii on DC
v3: Added Mullins to the list
Cc: stable@vger.kernel.org
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit be1c63c801 upstream.
When doing a modeset where the sink is transitioning from D3 to D0 , it
would sometimes be possible for the initial power_up_phy() to start
timing out. This would only be observed in the last action before the
sink went into D3 mode was intel_dp_sink_dpms(DRM_MODE_DPMS_OFF). We
originally thought this might be an issue with us accidentally shutting
off the aux block when putting the sink into D3, but since the DP spec
mandates that sinks must wake up within 1ms while we have 100ms to
respond to an ESI irq, this didn't really add up. Turns out that the
problem is more subtle then that:
It turns out that the timeout is from us not enabling DPMS on the MST
hub before actually trying to initiate sideband communications. This
would cause the first sideband communication (power_up_phy()), to start
timing out because the sink wasn't ready to respond. Afterwards, we
would call intel_dp_sink_dpms(DRM_MODE_DPMS_ON) in
intel_ddi_pre_enable_dp(), which would actually result in waking up the
sink so that sideband requests would work again.
Since DPMS is what lets us actually bring the hub up into a state where
sideband communications become functional again, we just need to make
sure to enable DPMS on the display before attempting to perform sideband
communications.
Changes since v1:
- Remove comment above if (!intel_dp->is_mst) - vsryjala
- Move intel_dp_sink_dpms() for MST into intel_dp_post_disable_mst() to
keep enable/disable paths symmetrical
- Improve commit message - dhnkrn
Changes since v2:
- Only send DPMS off when we're disabling the last sink, and only send
DPMS on when we're enabling the first sink - dhnkrn
Changes since v3:
- Check against is_mst, not intel_dp->is_mst - dhnkrn/vsyrjala
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Laura Abbott <labbott@redhat.com>
Cc: stable@vger.kernel.org
Fixes: ad260ab32a ("drm/i915/dp: Write to SET_POWER dpcd to enable MST hub.")
Link: https://patchwork.freedesktop.org/patch/msgid/20180407011053.22437-1-lyude@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 97028037a3 upstream.
So, unfortunately I recently made the discovery that in the upstream
kernel, the only reason that amdgpu is not currently suffering from
issues with runtime PM putting the GPU into suspend while it's driving
displays is due to the fact that on most prime systems, we have sound
devices associated with the GPU that hold their own runtime PM ref for
the GPU.
What this means however, is that in the event that there isn't any kind
of sound device active (which can easily be reproduced by building a
kernel with sound drivers disabled), the GPU will fall asleep even when
there's displays active. This appears to be in part due to the fact that
amdgpu has not actually ever relied on it's rpm_idle() function to be
the only thing keeping it running, and normally grabs it's own power
references whenever there are displays active (as can be seen with the
original pre-DC codepath in amdgpu_display_crtc_set_config() in
amdgpu_display.c). This means it's very likely that this bug was
introduced during the switch over the DC.
So to fix this, we start grabbing runtime PM references every time we
enable a previously disabled CRTC in atomic_commit_tail(). This appears
to be the correct solution, as it matches up with what i915 does in
i915/intel_runtime_pm.c.
The one sideaffect of this is that we ignore the variable that the
pre-DC code used to use for tracking when it needed runtime PM refs,
adev->have_disp_power_ref. This is mainly because there's no way for a
driver to tell whether or not all of it's CRTCs are enabled or disabled
when we've begun committing an atomic state, as there may be CRTC
commits happening in parallel that aren't contained within the atomic
state being committed. So, it's safer to just get/put a reference for
each CRTC being enabled or disabled in the new atomic state.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Acked-by: Christian König <christian.koenig@amd.com>.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 20dcff436e upstream.
After the commit
7d8905d064 ("serial: 8250_pci: Enable device after we check black list")
pure serial multi-port cards, such as CH355, got blacklisted and thus
not being enumerated anymore. Previously, it seems, blacklisting them
was on purpose to shut up pciserial_init_one() about record duplication.
So, remove the entries from blacklist in order to get cards enumerated.
Fixes: 7d8905d064 ("serial: 8250_pci: Enable device after we check black list")
Reported-by: Matt Turner <mattst88@gmail.com>
Cc: Sergej Pupykin <ml@sergej.pp.ru>
Cc: Alexandr Petrenko <petrenkoas83@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-and-Tested-by: Matt Turner <mattst88@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b02ec67a8e upstream.
Interrupts are ignored if no event bit is set in the status status
register and this breaks the buffer interface. No data is shown when
running "iio_generic_buffer -n mma8451 -a" and interrupt counts go
crazy.
Fix by not returning IRQ_NONE if DRDY is set.
Fixes: 605f72de13 ("iio: accel: mma8452: improvements to handle
multiple events")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ebec3f8f52 upstream.
syzbot is reporting stalls at __process_echoes() [1]. This is because
since ldata->echo_commit < ldata->echo_tail becomes true for some reason,
the discard loop is serving as almost infinite loop. This patch tries to
avoid falling into ldata->echo_commit < ldata->echo_tail situation by
making access to echo_* variables more carefully.
Since reset_buffer_flags() is called without output_lock held, it should
not touch echo_* variables. And omit a call to reset_buffer_flags() from
n_tty_open() by using vzalloc().
Since add_echo_byte() is called without output_lock held, it needs memory
barrier between storing into echo_buf[] and incrementing echo_head counter.
echo_buf() needs corresponding memory barrier before reading echo_buf[].
Lack of handling the possibility of not-yet-stored multi-byte operation
might be the reason of falling into ldata->echo_commit < ldata->echo_tail
situation, for if I do WARN_ON(ldata->echo_commit == tail + 1) prior to
echo_buf(ldata, tail + 1), the WARN_ON() fires.
Also, explicitly masking with buffer for the former "while" loop, and
use ldata->echo_commit > tail for the latter "while" loop.
[1] https://syzkaller.appspot.com/bug?id=17f23b094cd80df750e5b0f8982c521ee6bcbf40
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reported-by: syzbot <syzbot+108696293d7a21ab688f@syzkaller.appspotmail.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 68816e16b4 upstream.
According to UCSI Specification, Connector Change Event only
means a change in the Connector Status and Operation Mode
fields of the STATUS data structure. So any other change
should create another event.
Unfortunately on some platforms the firmware acting as PPM
(platform policy manager - usually embedded controller
firmware) still does not report any other status changes if
there is a connector change event. So if the connector power
or data role was changed when a device was plugged to the
connector, the driver does not get any indication about
that. The port will show wrong roles if that happens.
To fix the issue, always checking the data and power role
together with a connector change event.
Fixes: c1b0bc2dab ("usb: typec: Add support for UCSI interface")
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f9f9d168c upstream.
This fixes an issue where the driver fails with an error:
ioremap error for 0x3f799000-0x3f79a000, requested 0x2, got 0x0
On some platforms the UCSI ACPI mailbox SystemMemory
Operation Region may be setup before the driver has been
loaded. That will lead into the driver failing to map the
mailbox region, as it has been already marked as write-back
memory. acpi_os_ioremap() for x86 uses ioremap_cache()
unconditionally.
When the issue happens, the embedded controller has a
pending query event for the UCSI notification right after
boot-up which causes the operation region to be setup before
UCSI driver has been loaded.
The fix is to notify acpi core that the driver is about to
access memory region which potentially overlaps with an
operation region right before mapping it.
acpi_release_memory() will check if the memory has already
been setup (mapped) by acpi core, and deactivate it (unmap)
if it has. The driver is then able to map the memory with
ioremap_nocache() and set the memtype to uncached for the
region.
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Fixes: 8243edf441 ("usb: typec: ucsi: Add ACPI driver")
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d2d2e3c46b upstream.
Sometimes memory resource may be overlapping with
SystemMemory Operation Region by design, for example if the
memory region is used as a mailbox for communication with a
firmware in the system. One occasion of such mailboxes is
USB Type-C Connector System Software Interface (UCSI).
With regions like that, it is important that the driver is
able to map the memory with the requirements it has. For
example, the driver should be allowed to map the memory as
non-cached memory. However, if the operation region has been
accessed before the driver has mapped the memory, the memory
has been marked as write-back by the time the driver is
loaded. That means the driver will fail to map the memory
if it expects non-cached memory.
To work around the problem, introducing helper that the
drivers can use to temporarily deactivate (unmap)
SystemMemory Operation Regions that overlap with their
IO memory.
Fixes: 8243edf441 ("usb: typec: ucsi: Add ACPI driver")
Cc: stable@vger.kernel.org
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d5a4f93511 upstream.
The port->logbuffer_head may be wrong if the two processes enters
_tcpm_log at the mostly same time. The 2nd process enters _tcpm_log
before the 1st process update the index, then the 2nd process will
not allocate logbuffer, when the 2nd process tries to use log buffer,
the index has already updated by the 1st process, so it will get
NULL pointer for updated logbuffer, the error message like below:
tcpci 0-0050: Log buffer index 6 is NULL
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8760675932 upstream.
The dwc2_get_ls_map() use ttport to reference into the
bitmap if we're on a multi_tt hub. But the bitmaps index
from 0 to (hub->maxchild - 1), while the ttport index from
1 to hub->maxchild. This will cause invalid memory access
when the number of ttport is hub->maxchild.
Without this patch, I can easily meet a Kernel panic issue
if connect a low-speed USB mouse with the max port of FE2.1
multi-tt hub (1a40:0201) on rk3288 platform.
Fixes: 9f9f09b048 ("usb: dwc2: host: Totally redo the microframe scheduler")
Cc: <stable@vger.kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Minas Harutyunyan hminas@synopsys.com>
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f83982338 upstream.
Silicon Labs defines alternative VID/PID pairs for some chips that when
used will automatically install drivers for Windows users without manual
intervention. Unfortunately, these IDs are not recognized by the Linux
module, so using these IDs improves user experience on one platform but
degrades it on Linux. This patch addresses this problem.
Signed-off-by: Karoly Pados <pados@pados.hu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd23a72698 upstream.
In vbg_misc_device_ioctl(), the header of the ioctl argument is copied from
the userspace pointer 'arg' and saved to the kernel object 'hdr'. Then the
'version', 'size_in', and 'size_out' fields of 'hdr' are verified.
Before this commit, after the checks a buffer for the entire request would
be allocated and then all data including the verified header would be
copied from the userspace 'arg' pointer again.
Given that the 'arg' pointer resides in userspace, a malicious userspace
process can race to change the data pointed to by 'arg' between the two
copies. By doing so, the user can bypass the verifications on the ioctl
argument.
This commit fixes this by using the already checked copy of the header
to fill the header part of the allocated buffer and only copying the
remainder of the data from userspace.
Signed-off-by: Wenwen Wang <wang6495@umn.edu>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Cc: Justin Forbes <jmforbes@linuxtx.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a685557fbb upstream.
Discards issued to a DM thin device can complete to userspace (via
fstrim) _before_ the metadata changes associated with the discards is
reflected in the thinp superblock (e.g. free blocks). As such, if a
user constructs a test that loops repeatedly over these steps, block
allocation can fail due to discards not having completed yet:
1) fill thin device via filesystem file
2) remove file
3) fstrim
From initial report, here:
https://www.redhat.com/archives/dm-devel/2018-April/msg00022.html
"The root cause of this issue is that dm-thin will first remove
mapping and increase corresponding blocks' reference count to prevent
them from being reused before DISCARD bios get processed by the
underlying layers. However. increasing blocks' reference count could
also increase the nr_allocated_this_transaction in struct sm_disk
which makes smd->old_ll.nr_allocated +
smd->nr_allocated_this_transaction bigger than smd->old_ll.nr_blocks.
In this case, alloc_data_block() will never commit metadata to reset
the begin pointer of struct sm_disk, because sm_disk_get_nr_free()
always return an underflow value."
While there is room for improvement to the space-map accounting that
thinp is making use of: the reality is this test is inherently racey and
will result in the previous iteration's fstrim's discard(s) completing
vs concurrent block allocation, via dd, in the next iteration of the
loop.
No amount of space map accounting improvements will be able to allow
user's to use a block before a discard of that block has completed.
So the best we can really do is allow DM thinp to gracefully handle such
aggressive use of all the pool's data by degrading the pool into
out-of-data-space (OODS) mode. We _should_ get that behaviour already
(if space map accounting didn't falsely cause alloc_data_block() to
believe free space was available).. but short of that we handle the
current reality that dm_pool_alloc_data_block() can return -ENOSPC.
Reported-by: Dennis Yang <dennisyang@qnap.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0da74120c5 upstream.
If a user is accessing a file in selinuxfs with a pointer to a userspace
buffer that is backed by e.g. a userfaultfd, the userspace access can
stall indefinitely, which can block fsi->mutex if it is held.
For sel_read_policy(), remove the locking, since this method doesn't seem
to access anything that requires locking.
For sel_read_bool(), move the user access below the locked region.
For sel_write_bool() and sel_commit_bools_write(), move the user access
up above the locked region.
Cc: stable@vger.kernel.org
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Jann Horn <jannh@google.com>
Acked-by: Stephen Smalley <sds@tycho.nsa.gov>
[PM: removed an unused variable in sel_read_policy()]
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 124049decb upstream.
There is a kernel panic that is triggered when reading /proc/kpageflags
on the kernel booted with kernel parameter 'memmap=nn[KMG]!ss[KMG]':
BUG: unable to handle kernel paging request at fffffffffffffffe
PGD 9b20e067 P4D 9b20e067 PUD 9b210067 PMD 0
Oops: 0000 [#1] SMP PTI
CPU: 2 PID: 1728 Comm: page-types Not tainted 4.17.0-rc6-mm1-v4.17-rc6-180605-0816-00236-g2dfb086ef02c+ #160
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.0-2.fc28 04/01/2014
RIP: 0010:stable_page_flags+0x27/0x3c0
Code: 00 00 00 0f 1f 44 00 00 48 85 ff 0f 84 a0 03 00 00 41 54 55 49 89 fc 53 48 8b 57 08 48 8b 2f 48 8d 42 ff 83 e2 01 48 0f 44 c7 <48> 8b 00 f6 c4 01 0f 84 10 03 00 00 31 db 49 8b 54 24 08 4c 89 e7
RSP: 0018:ffffbbd44111fde0 EFLAGS: 00010202
RAX: fffffffffffffffe RBX: 00007fffffffeff9 RCX: 0000000000000000
RDX: 0000000000000001 RSI: 0000000000000202 RDI: ffffed1182fff5c0
RBP: ffffffffffffffff R08: 0000000000000001 R09: 0000000000000001
R10: ffffbbd44111fed8 R11: 0000000000000000 R12: ffffed1182fff5c0
R13: 00000000000bffd7 R14: 0000000002fff5c0 R15: ffffbbd44111ff10
FS: 00007efc4335a500(0000) GS:ffff93a5bfc00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: fffffffffffffffe CR3: 00000000b2a58000 CR4: 00000000001406e0
Call Trace:
kpageflags_read+0xc7/0x120
proc_reg_read+0x3c/0x60
__vfs_read+0x36/0x170
vfs_read+0x89/0x130
ksys_pread64+0x71/0x90
do_syscall_64+0x5b/0x160
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x7efc42e75e23
Code: 09 00 ba 9f 01 00 00 e8 ab 81 f4 ff 66 2e 0f 1f 84 00 00 00 00 00 90 83 3d 29 0a 2d 00 00 75 13 49 89 ca b8 11 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 34 c3 48 83 ec 08 e8 db d3 01 00 48 89 04 24
According to kernel bisection, this problem became visible due to commit
f7f99100d8 ("mm: stop zeroing memory during allocation in vmemmap")
which changes how struct pages are initialized.
Memblock layout affects the pfn ranges covered by node/zone. Consider
that we have a VM with 2 NUMA nodes and each node has 4GB memory, and
the default (no memmap= given) memblock layout is like below:
MEMBLOCK configuration:
memory size = 0x00000001fff75c00 reserved size = 0x000000000300c000
memory.cnt = 0x4
memory[0x0] [0x0000000000001000-0x000000000009efff], 0x000000000009e000 bytes on node 0 flags: 0x0
memory[0x1] [0x0000000000100000-0x00000000bffd6fff], 0x00000000bfed7000 bytes on node 0 flags: 0x0
memory[0x2] [0x0000000100000000-0x000000013fffffff], 0x0000000040000000 bytes on node 0 flags: 0x0
memory[0x3] [0x0000000140000000-0x000000023fffffff], 0x0000000100000000 bytes on node 1 flags: 0x0
...
If you give memmap=1G!4G (so it just covers memory[0x2]),
the range [0x100000000-0x13fffffff] is gone:
MEMBLOCK configuration:
memory size = 0x00000001bff75c00 reserved size = 0x000000000300c000
memory.cnt = 0x3
memory[0x0] [0x0000000000001000-0x000000000009efff], 0x000000000009e000 bytes on node 0 flags: 0x0
memory[0x1] [0x0000000000100000-0x00000000bffd6fff], 0x00000000bfed7000 bytes on node 0 flags: 0x0
memory[0x2] [0x0000000140000000-0x000000023fffffff], 0x0000000100000000 bytes on node 1 flags: 0x0
...
This causes shrinking node 0's pfn range because it is calculated by the
address range of memblock.memory. So some of struct pages in the gap
range are left uninitialized.
We have a function zero_resv_unavail() which does zeroing the struct pages
within the reserved unavailable range (i.e. memblock.memory &&
!memblock.reserved). This patch utilizes it to cover all unavailable
ranges by putting them into memblock.reserved.
Link: http://lkml.kernel.org/r/20180615072947.GB23273@hori1.linux.bs1.fc.nec.co.jp
Fixes: f7f99100d8 ("mm: stop zeroing memory during allocation in vmemmap")
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Tested-by: Oscar Salvador <osalvador@suse.de>
Tested-by: "Herton R. Krzesinski" <herton@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Pavel Tatashin <pasha.tatashin@oracle.com>
Cc: Steven Sistare <steven.sistare@oracle.com>
Cc: Daniel Jordan <daniel.m.jordan@oracle.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4557641b4c upstream.
QUEUE_FLAG_DAX is an indication that a given block device supports
filesystem DAX and should not be set for PMEM namespaces which are in "raw"
mode. These namespaces lack struct page and are prevented from
participating in filesystem DAX as of commit 569d0365f5 ("dax: require
'struct page' by default for filesystem dax").
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Suggested-by: Mike Snitzer <snitzer@redhat.com>
Fixes: 569d0365f5 ("dax: require 'struct page' by default for filesystem dax")
Cc: stable@vger.kernel.org
Acked-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f21c601a2b upstream.
Use of bio_clone_bioset() is inefficient if there is no need to clone
the original bio's bio_vec array. Best to use the bio_clone_fast()
variant. Also, just using bio_advance() is only part of what is needed
to properly setup the clone -- it doesn't account for the various
bio_integrity() related work that also needs to be performed (see
bio_split).
Address both of these issues by switching from bio_clone_bioset() to
bio_split().
Fixes: 18a25da8 ("dm: ensure bio submission follows a depth-first tree walk")
Cc: stable@vger.kernel.org # 4.15+, requires removal of '&' before md->queue->bio_split
Reported-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d50d82faa0 upstream.
In kernel 4.17 I removed some code from dm-bufio that did slab cache
merging (commit 21bb132767: "dm bufio: remove code that merges slab
caches") - both slab and slub support merging caches with identical
attributes, so dm-bufio now just calls kmem_cache_create and relies on
implicit merging.
This uncovered a bug in the slub subsystem - if we delete a cache and
immediatelly create another cache with the same attributes, it fails
because of duplicate filename in /sys/kernel/slab/. The slub subsystem
offloads freeing the cache to a workqueue - and if we create the new
cache before the workqueue runs, it complains because of duplicate
filename in sysfs.
This patch fixes the bug by moving the call of kobject_del from
sysfs_slab_remove_workfn to shutdown_cache. kobject_del must be called
while we hold slab_mutex - so that the sysfs entry is deleted before a
cache with the same attributes could be created.
Running device-mapper-test-suite with:
dmtest run --suite thin-provisioning -n /commit_failure_causes_fallback/
triggered:
Buffer I/O error on dev dm-0, logical block 1572848, async page read
device-mapper: thin: 253:1: metadata operation 'dm_pool_alloc_data_block' failed: error = -5
device-mapper: thin: 253:1: aborting current metadata transaction
sysfs: cannot create duplicate filename '/kernel/slab/:a-0000144'
CPU: 2 PID: 1037 Comm: kworker/u48:1 Not tainted 4.17.0.snitm+ #25
Hardware name: Supermicro SYS-1029P-WTR/X11DDW-L, BIOS 2.0a 12/06/2017
Workqueue: dm-thin do_worker [dm_thin_pool]
Call Trace:
dump_stack+0x5a/0x73
sysfs_warn_dup+0x58/0x70
sysfs_create_dir_ns+0x77/0x80
kobject_add_internal+0xba/0x2e0
kobject_init_and_add+0x70/0xb0
sysfs_slab_add+0xb1/0x250
__kmem_cache_create+0x116/0x150
create_cache+0xd9/0x1f0
kmem_cache_create_usercopy+0x1c1/0x250
kmem_cache_create+0x18/0x20
dm_bufio_client_create+0x1ae/0x410 [dm_bufio]
dm_block_manager_create+0x5e/0x90 [dm_persistent_data]
__create_persistent_data_objects+0x38/0x940 [dm_thin_pool]
dm_pool_abort_metadata+0x64/0x90 [dm_thin_pool]
metadata_operation_failed+0x59/0x100 [dm_thin_pool]
alloc_data_block.isra.53+0x86/0x180 [dm_thin_pool]
process_cell+0x2a3/0x550 [dm_thin_pool]
do_worker+0x28d/0x8f0 [dm_thin_pool]
process_one_work+0x171/0x370
worker_thread+0x49/0x3f0
kthread+0xf8/0x130
ret_from_fork+0x35/0x40
kobject_add_internal failed for :a-0000144 with -EEXIST, don't try to register things with the same name in the same directory.
kmem_cache_create(dm_bufio_buffer-16) failed with error -17
Link: http://lkml.kernel.org/r/alpine.LRH.2.02.1806151817130.6333@file01.intranet.prod.int.rdu2.redhat.com
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reported-by: Mike Snitzer <snitzer@redhat.com>
Tested-by: Mike Snitzer <snitzer@redhat.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e41fc8c5bd upstream.
We have 3 more Lenovo machines, they all have 2 front mics on them,
so they need the fixup to change the location for one of two mics.
Among these 3 Lenovo machines, one of them has the same pin cfg as the
machine with subid 0x17aa3138, so use the pin cfg table to apply fixup
for them. The rest machines don't share the same pin cfg, so far use
the subid to apply fixup for them.
Fixes: a3dafb2200 ("ALSA: hda/realtek - adjust the location of one mic")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d5a6cabf02 upstream.
Some Lenovo laptops, e.g. Lenovo P50, showed the pop noise at resume
or runtime resume. It turned out to be reduced by applying
alc_no_shutup() just like TPT440 quirk does.
Since there are many Lenovo models showing the same behavior, put this
workaround in ALC269_FIXUP_THINKPAD_ACPI entry so that it's applied
commonly to all such Lenovo machines.
Reported-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Benjamin Berg <bberg@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 57cb54e53b upstream.
Henning Kühn reported that the discrete AMD GPU on his hybrid graphics
laptop no longer runtime-suspends due to the recent commit
07f4f97d7b ("vga_switcheroo: Use device link for HDA controller").
The root cause is that the HDMI codec on AMD GPU doesn't support
CLKSTOP and EPSS, which are currently mandatory for powering down the
HD-audio link at runtime suspend. Because the HD-audio link is still
up, HD-audio controller driver blocks the transition to D3.
For addressing the regression, this patch adds a new flag to indicate
the forced link-down, and sets it for AMD HDMI codecs appropriately
in the codec driver.
Fixes: 07f4f97d7b ("vga_switcheroo: Use device link for HDA controller")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106957
Reported-by: Lukas Wunner <lukas@wunner.de>
Reported-and-tested-by: Henning Kühn <prg@cooco.de>
Cc: <stable@vger.kernel.org> # v4.17+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b41f794f28 upstream.
The kernel may spew a WARNING about UBSAN undefined behavior at
handling ALSA timer ioctl SNDRV_TIMER_IOCTL_NEXT_DEVICE:
UBSAN: Undefined behaviour in sound/core/timer.c:1524:19
signed integer overflow:
2147483647 + 1 cannot be represented in type 'int'
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x122/0x1c8 lib/dump_stack.c:113
ubsan_epilogue+0x12/0x86 lib/ubsan.c:159
handle_overflow+0x1c2/0x21f lib/ubsan.c:190
__ubsan_handle_add_overflow+0x2a/0x31 lib/ubsan.c:198
snd_timer_user_next_device sound/core/timer.c:1524 [inline]
__snd_timer_user_ioctl+0x204d/0x2520 sound/core/timer.c:1939
snd_timer_user_ioctl+0x67/0x95 sound/core/timer.c:1994
....
It happens only when a value with INT_MAX is passed, as we're
incrementing it unconditionally. So the fix is trivial, check the
value with INT_MAX. Although the bug itself is fairly harmless, it's
better to fix it so that fuzzers won't hit this again later.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=200213
Reported-and-tested-by: Team OWL337 <icytxw@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 50fc7b6195 upstream.
Commit 40f7090bb1 ("Input: elan_i2c_smbus - fix corrupted stack")
fixed most of the functions using i2c_smbus_read_block_data() to
allocate a buffer with the maximum block size. However three
functions were left unchanged:
* In elan_smbus_initialize(), increase the buffer size in the same
way.
* In elan_smbus_calibrate_result(), the buffer is provided by the
caller (calibrate_store()), so introduce a bounce buffer. Also
name the result buffer size.
* In elan_smbus_get_report(), the buffer is provided by the caller
but happens to be the right length. Add a compile-time assertion
to ensure this remains the case.
Cc: <stable@vger.kernel.org> # 3.19+
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 03ae3a9caf upstream.
The commit ba667650c5 ("Input: psmouse - clean up code") was pretty
brain-dead and broke extra buttons reporting for variety of PS/2 mice:
Genius, Thinkmouse and Intellimouse Explorer. We need to actually inspect
the data coming from the device when reporting events.
Fixes: ba667650c5 ("Input: psmouse - clean up code")
Reported-by: Jiri Slaby <jslaby@suse.cz>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd6bee81c9 upstream.
This fixes using the controller with SDL2.
SDL2 has a naive algorithm to apply the correct settings to a controller.
For X-Box compatible controllers it expects that the controller name
contains a variation of a 'XBOX'-string.
This patch changes the identifier to contain "X-Box" as substring. Tested
with Steam and C-Dogs-SDL which both detect the controller properly after
adding this patch.
Fixes: c1ba08390a ("Input: xpad - add GPD Win 2 Controller USB IDs")
Cc: stable@vger.kernel.org
Signed-off-by: Enno Boland <gottox@voidlinux.eu>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fa65653e57 upstream.
Detect when a directory entry is (possibly partially) beyond directory
size and return EIO in that case since it means the filesystem is
corrupted. Otherwise directory operations can further corrupt the
directory and possibly also oops the kernel.
CC: Anatoly Trosinenko <anatoly.trosinenko@gmail.com>
CC: stable@vger.kernel.org
Reported-and-tested-by: Anatoly Trosinenko <anatoly.trosinenko@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc45519eb1 upstream.
This patch reverts commit 3243ff2a05 ("net: ethernet: davinci_emac:
Deduplicate bus_find_device() by name matching") and adds a comment
which should stop anyone from reintroducing the same "fix" in the future.
We can't use bus_find_device_by_name() here because the device name is
not guaranteed to be 'davinci_mdio'. On some systems it can be
'davinci_mdio.0' so we need to use strncmp() against the first part of
the string to correctly match it.
Fixes: 3243ff2a05 ("net: ethernet: davinci_emac: Deduplicate bus_find_device() by name matching")
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eef04c7b37 upstream.
Commit 910f8befdf ("xen/pirq: fix error path cleanup when binding
MSIs") fixed a couple of errors in error cleanup path of
xen_bind_pirq_msi_to_irq(). This cleanup allowed a call to
__unbind_from_irq() with an unbound irq, which would result in
triggering the BUG_ON there.
Since there is really no reason for the BUG_ON (xen_free_irq() can
operate on unbound irqs) we can remove it.
Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: stable@vger.kernel.org
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 70303420b5 upstream.
The syzkaller detected a out-of-bounds issue with the events filter code,
specifically here:
prog[N].pred = NULL; /* #13 */
prog[N].target = 1; /* TRUE */
prog[N+1].pred = NULL;
prog[N+1].target = 0; /* FALSE */
-> prog[N-1].target = N;
prog[N-1].when_to_branch = false;
As that's the first reference to a "N-1" index, it appears that the code got
here with N = 0, which means the filter parser found no filter to parse
(which shouldn't ever happen, but apparently it did).
Add a new error to the parsing code that will check to make sure that N is
not zero before going into this part of the code. If N = 0, then -EINVAL is
returned, and a error message is added to the filter.
Cc: stable@vger.kernel.org
Fixes: 80765597bc ("tracing: Rewrite filter logic to be simpler and faster")
Reported-by: air icy <icytxw@gmail.com>
bugzilla url: https://bugzilla.kernel.org/show_bug.cgi?id=200019
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2bdce74412 upstream.
Hussam reports:
I was poking around and for no real reason, I did cat /dev/mem and
strings /dev/mem. Then I saw the following warning in dmesg. I saved it
and rebooted immediately.
memremap attempted on mixed range 0x000000000009c000 size: 0x1000
------------[ cut here ]------------
WARNING: CPU: 0 PID: 11810 at kernel/memremap.c:98 memremap+0x104/0x170
[..]
Call Trace:
xlate_dev_mem_ptr+0x25/0x40
read_mem+0x89/0x1a0
__vfs_read+0x36/0x170
The memremap() implementation checks for attempts to remap System RAM
with MEMREMAP_WB and instead redirects those mapping attempts to the
linear map. However, that only works if the physical address range
being remapped is page aligned. In low memory we have situations like
the following:
00000000-00000fff : Reserved
00001000-0009fbff : System RAM
0009fc00-0009ffff : Reserved
...where System RAM intersects Reserved ranges on a sub-page page
granularity.
Given that devmem_is_allowed() special cases any attempt to map System
RAM in the first 1MB of memory, replace page_is_ram() with the more
precise region_intersects() to trap attempts to map disallowed ranges.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199999
Link: http://lkml.kernel.org/r/152856436164.18127.2847888121707136898.stgit@dwillia2-desk3.amr.corp.intel.com
Fixes: 92281dee82 ("arch: introduce memremap()")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reported-by: Hussam Al-Tayeb <me@hussam.eu.org>
Tested-by: Hussam Al-Tayeb <me@hussam.eu.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1105a2fc02 upstream.
In our armv8a server(QDF2400), I noticed lots of WARN_ON caused by
PAGE_SIZE unaligned for rmap_item->address under memory pressure
tests(start 20 guests and run memhog in the host).
WARNING: CPU: 4 PID: 4641 at virt/kvm/arm/mmu.c:1826 kvm_age_hva_handler+0xc0/0xc8
CPU: 4 PID: 4641 Comm: memhog Tainted: G W 4.17.0-rc3+ #8
Call trace:
kvm_age_hva_handler+0xc0/0xc8
handle_hva_to_gpa+0xa8/0xe0
kvm_age_hva+0x4c/0xe8
kvm_mmu_notifier_clear_flush_young+0x54/0x98
__mmu_notifier_clear_flush_young+0x6c/0xa0
page_referenced_one+0x154/0x1d8
rmap_walk_ksm+0x12c/0x1d0
rmap_walk+0x94/0xa0
page_referenced+0x194/0x1b0
shrink_page_list+0x674/0xc28
shrink_inactive_list+0x26c/0x5b8
shrink_node_memcg+0x35c/0x620
shrink_node+0x100/0x430
do_try_to_free_pages+0xe0/0x3a8
try_to_free_pages+0xe4/0x230
__alloc_pages_nodemask+0x564/0xdc0
alloc_pages_vma+0x90/0x228
do_anonymous_page+0xc8/0x4d0
__handle_mm_fault+0x4a0/0x508
handle_mm_fault+0xf8/0x1b0
do_page_fault+0x218/0x4b8
do_translation_fault+0x90/0xa0
do_mem_abort+0x68/0xf0
el0_da+0x24/0x28
In rmap_walk_ksm, the rmap_item->address might still have the
STABLE_FLAG, then the start and end in handle_hva_to_gpa might not be
PAGE_SIZE aligned. Thus it will cause exceptions in handle_hva_to_gpa
on arm64.
This patch fixes it by ignoring (not removing) the low bits of address
when doing rmap_walk_ksm.
IMO, it should be backported to stable tree. the storm of WARN_ONs is
very easy for me to reproduce. More than that, I watched a panic (not
reproducible) as follows:
page:ffff7fe003742d80 count:-4871 mapcount:-2126053375 mapping: (null) index:0x0
flags: 0x1fffc00000000000()
raw: 1fffc00000000000 0000000000000000 0000000000000000 ffffecf981470000
raw: dead000000000100 dead000000000200 ffff8017c001c000 0000000000000000
page dumped because: nonzero _refcount
CPU: 29 PID: 18323 Comm: qemu-kvm Tainted: G W 4.14.15-5.hxt.aarch64 #1
Hardware name: <snip for confidential issues>
Call trace:
dump_backtrace+0x0/0x22c
show_stack+0x24/0x2c
dump_stack+0x8c/0xb0
bad_page+0xf4/0x154
free_pages_check_bad+0x90/0x9c
free_pcppages_bulk+0x464/0x518
free_hot_cold_page+0x22c/0x300
__put_page+0x54/0x60
unmap_stage2_range+0x170/0x2b4
kvm_unmap_hva_handler+0x30/0x40
handle_hva_to_gpa+0xb0/0xec
kvm_unmap_hva_range+0x5c/0xd0
I even injected a fault on purpose in kvm_unmap_hva_range by seting
size=size-0x200, the call trace is similar as above. So I thought the
panic is similarly caused by the root cause of WARN_ON.
Andrea said:
: It looks a straightforward safe fix, on x86 hva_to_gfn_memslot would
: zap those bits and hide the misalignment caused by the low metadata
: bits being erroneously left set in the address, but the arm code
: notices when that's the last page in the memslot and the hva_end is
: getting aligned and the size is below one page.
:
: I think the problem triggers in the addr += PAGE_SIZE of
: unmap_stage2_ptes that never matches end because end is aligned but
: addr is not.
:
: } while (pte++, addr += PAGE_SIZE, addr != end);
:
: x86 again only works on hva_start/hva_end after converting it to
: gfn_start/end and that being in pfn units the bits are zapped before
: they risk to cause trouble.
Jia He said:
: I've tested by myself in arm64 server (QDF2400,46 cpus,96G mem) Without
: this patch, the WARN_ON is very easy for reproducing. After this patch, I
: have run the same benchmarch for a whole day without any WARN_ONs
Link: http://lkml.kernel.org/r/1525403506-6750-1-git-send-email-hejianet@gmail.com
Signed-off-by: Jia He <jia.he@hxt-semitech.com>
Reviewed-by: Andrea Arcangeli <aarcange@redhat.com>
Tested-by: Jia He <hejianet@gmail.com>
Cc: Suzuki K Poulose <Suzuki.Poulose@arm.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Cc: Arvind Yadav <arvind.yadav.cs@gmail.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23edca8649 upstream.
There is a problem if we are going to unmap a rbd device and the
watch_dwork is going to queue delayed work for watch:
unmap Thread watch Thread timer
do_rbd_remove
cancel_tasks_sync(rbd_dev)
queue_delayed_work for watch
destroy_workqueue(rbd_dev->task_wq)
drain_workqueue(wq)
destroy other resources in wq
call_timer_fn
__queue_work()
Then the delayed work escape the cancel_tasks_sync() and
destroy_workqueue() and we will get an user-after-free call trace:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
PGD 0 P4D 0
Oops: 0000 [#1] SMP PTI
Modules linked in:
CPU: 7 PID: 0 Comm: swapper/7 Tainted: G OE 4.17.0-rc6+ #13
Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
RIP: 0010:__queue_work+0x6a/0x3b0
RSP: 0018:ffff9427df1c3e90 EFLAGS: 00010086
RAX: ffff9427deca8400 RBX: 0000000000000000 RCX: 0000000000000000
RDX: ffff9427deca8400 RSI: ffff9427df1c3e50 RDI: 0000000000000000
RBP: ffff942783e39e00 R08: ffff9427deca8400 R09: ffff9427df1c3f00
R10: 0000000000000004 R11: 0000000000000005 R12: ffff9427cfb85970
R13: 0000000000002000 R14: 000000000001eca0 R15: 0000000000000007
FS: 0000000000000000(0000) GS:ffff9427df1c0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 00000004c900a005 CR4: 00000000000206e0
Call Trace:
<IRQ>
? __queue_work+0x3b0/0x3b0
call_timer_fn+0x2d/0x130
run_timer_softirq+0x16e/0x430
? tick_sched_timer+0x37/0x70
__do_softirq+0xd2/0x280
irq_exit+0xd5/0xe0
smp_apic_timer_interrupt+0x6c/0x130
apic_timer_interrupt+0xf/0x20
[ Move rbd_dev->watch_dwork cancellation so that rbd_reregister_watch()
either bails out early because the watch is UNREGISTERED at that point
or just gets cancelled. ]
Cc: stable@vger.kernel.org
Fixes: 99d1694310 ("rbd: retry watch re-registration periodically")
Signed-off-by: Dongsheng Yang <dongsheng.yang@easystack.cn>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d375b58c1 upstream.
On some devices the contents of the ctrl register get lost over a
suspend/resume and the PWM comes back up disabled after the resume.
This is seen on some Bay Trail devices with the PWM in ACPI enumerated
mode, so it shows up as a platform device instead of a PCI device.
If we still think it is enabled and then try to change the duty-cycle
after this, we end up with a "PWM_SW_UPDATE was not cleared" error and
the PWM is stuck in that state from then on.
This commit adds suspend and resume pm callbacks to the pwm-lpss-platform
code, which save/restore the ctrl register over a suspend/resume, fixing
this.
Note that:
1) There is no need to do this over a runtime suspend, since we
only runtime suspend when disabled and then we properly set the enable
bit and reprogram the timings when we re-enable the PWM.
2) This may be happening on more systems then we realize, but has been
covered up sofar by a bug in the acpi-lpss.c code which was save/restoring
the regular device registers instead of the lpss private registers due to
lpss_device_desc.prv_offset not being set. This is fixed by a later patch
in this series.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fdcb613d49 upstream.
The LPSS PWM device on on Bay Trail and Cherry Trail devices has a set
of private registers at offset 0x800, the current lpss_device_desc for
them already sets the LPSS_SAVE_CTX flag to have these saved/restored
over device-suspend, but the current lpss_device_desc was not setting
the prv_offset field, leading to the regular device registers getting
saved/restored instead.
This is causing the PWM controller to no longer work, resulting in a black
screen, after a suspend/resume on systems where the firmware clears the
APB clock and reset bits at offset 0x804.
This commit fixes this by properly setting prv_offset to 0x800 for
the PWM devices.
Cc: stable@vger.kernel.org
Fixes: e1c7481797 ("ACPI / LPSS: Add Intel BayTrail ACPI mode PWM")
Fixes: 1bfbd8eb8a ("ACPI / LPSS: Add ACPI IDs for Intel Braswell")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rafael J . Wysocki <rjw@rjwysocki.net>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d68894800e upstream.
In nfs_idmap_read_and_verify_message there is an incorrect sprintf '%d'
that converts the __u32 'im_id' from struct idmap_msg to 'id_str', which
is a stack char array variable of length NFS_UINT_MAXLEN == 11.
If a uid or gid value is > 2147483647 = 0x7fffffff, the conversion
overflows into a negative value, for example:
crash> p (unsigned) (0x80000000)
$1 = 2147483648
crash> p (signed) (0x80000000)
$2 = -2147483648
The '-' sign is written to the buffer and this causes a 1 byte overflow
when the NULL byte is written, which corrupts kernel stack memory. If
CONFIG_CC_STACKPROTECTOR_STRONG is set we see a stack-protector panic:
[11558053.616565] Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: ffffffffa05b8a8c
[11558053.639063] CPU: 6 PID: 9423 Comm: rpc.idmapd Tainted: G W ------------ T 3.10.0-514.el7.x86_64 #1
[11558053.641990] Hardware name: Red Hat OpenStack Compute, BIOS 1.10.2-3.el7_4.1 04/01/2014
[11558053.644462] ffffffff818c7bc0 00000000b1f3aec1 ffff880de0f9bd48 ffffffff81685eac
[11558053.646430] ffff880de0f9bdc8 ffffffff8167f2b3 ffffffff00000010 ffff880de0f9bdd8
[11558053.648313] ffff880de0f9bd78 00000000b1f3aec1 ffffffff811dcb03 ffffffffa05b8a8c
[11558053.650107] Call Trace:
[11558053.651347] [<ffffffff81685eac>] dump_stack+0x19/0x1b
[11558053.653013] [<ffffffff8167f2b3>] panic+0xe3/0x1f2
[11558053.666240] [<ffffffff811dcb03>] ? kfree+0x103/0x140
[11558053.682589] [<ffffffffa05b8a8c>] ? idmap_pipe_downcall+0x1cc/0x1e0 [nfsv4]
[11558053.689710] [<ffffffff810855db>] __stack_chk_fail+0x1b/0x30
[11558053.691619] [<ffffffffa05b8a8c>] idmap_pipe_downcall+0x1cc/0x1e0 [nfsv4]
[11558053.693867] [<ffffffffa00209d6>] rpc_pipe_write+0x56/0x70 [sunrpc]
[11558053.695763] [<ffffffff811fe12d>] vfs_write+0xbd/0x1e0
[11558053.702236] [<ffffffff810acccc>] ? task_work_run+0xac/0xe0
[11558053.704215] [<ffffffff811fec4f>] SyS_write+0x7f/0xe0
[11558053.709674] [<ffffffff816964c9>] system_call_fastpath+0x16/0x1b
Fix this by calling the internally defined nfs_map_numeric_to_string()
function which properly uses '%u' to convert this __u32. For consistency,
also replace the one other place where snprintf is called.
Signed-off-by: Dave Wysochanski <dwysocha@redhat.com>
Reported-by: Stephen Johnston <sjohnsto@redhat.com>
Fixes: cf4ab538f1 ("NFSv4: Fix the string length returned by the idmapper")
Cc: stable@vger.kernel.org # v3.4+
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9c2ece6ef6 upstream.
nfsd4_readdir_rsize restricts rd_maxcount to svc_max_payload when
estimating the size of the readdir reply, but nfsd_encode_readdir
restricts it to INT_MAX when encoding the reply. This can result in log
messages like "kernel: RPC request reserved 32896 but used 1049444".
Restrict rd_dircount similarly (no reason it should be larger than
svc_max_payload).
Signed-off-by: Scott Mayhew <smayhew@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 76d81243a4 upstream.
As warned by smatch:
drivers/media/dvb-core/dvb_frontend.c:314 dvb_frontend_get_event() warn: inconsistent returns 'sem:&fepriv->sem'.
Locked on: line 288
line 295
line 306
line 314
Unlocked on: line 303
The lock implementation for get event is wrong, as, if an
interrupt occurs, down_interruptible() will fail, and the
routine will call up() twice when userspace calls the ioctl
again.
The bad code is there since when Linux migrated to git, in
2005.
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 63039c29f7 upstream.
The MCE Remote sends a 0 scancode when keys are released. If this is not
received or decoded, then keys can get "stuck"; the keyup event is not
sent since the input_sync() is missing from the timeout handler.
Cc: stable@vger.kernel.org
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea72fbf588 upstream.
As warned by smatch:
drivers/media/v4l2-core/v4l2-compat-ioctl32.c:879 put_v4l2_ext_controls32() warn: check for integer overflow 'count'
The access_ok() logic should check for too big arrays too.
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f620d1d7af upstream.
media: uvcvideo: Support UVC 1.5 video probe & commit controls
The length of UVC 1.5 video control is 48, and it is 34 for UVC 1.1.
Change it to 48 for UVC 1.5 device, and the UVC 1.5 device can be
recognized.
More changes to the driver are needed for full UVC 1.5 compatibility.
However, at least the UVC 1.5 Realtek RTS5847/RTS5852 cameras have been
reported to work well.
[laurent.pinchart@ideasonboard.com: Factor out code to helper function, update size checks]
Cc: stable@vger.kernel.org
Signed-off-by: ming_qian <ming_qian@realsil.com.cn>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Ana Guerrero Lopez <ana.guerrero@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 83967993f2 upstream.
Commit 372b2b0399 ("media: v4l: vsp1: Release buffers in
start_streaming error path") introduced a helper to clean up buffers on
error paths, but inadvertently changed the code such that only the
output WPF buffers were cleaned, rather than the video node being
operated on.
Since then vsp1_video_cleanup_pipeline() has grown to perform both video
node cleanup, as well as pipeline cleanup. Split the implementation into
two distinct functions that perform the required work, so that each
video node can release its buffers correctly on streamoff. The pipe
cleanup that was performed in the vsp1_video_stop_streaming() (releasing
the pipe->dl) is moved to the function for clarity.
Fixes: 372b2b0399 ("media: v4l: vsp1: Release buffers in start_streaming error path")
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c0b0d540db upstream.
Below two wrong nodes in existing DTS files would cause a fail boot since
in fact the address 0 is not the correct place the memory device locates
at.
memory {
device_type = "memory";
reg = <0x0 0x0 0x0 0x0>;
};
memory@80000000 {
reg = <0x0 0x80000000 0x0 0x40000000>;
};
In order to avoid having a memory node starting at address 0, we can't
include file skeleton64.dtsi and instead need to explicitly manually
define a few of properties the DTS relies on such as #address-cells
and #size-cells in root node and device_type in the node memory@80000000.
Cc: stable@vger.kernel.org
Fixes: 31ac0d69a1 ("ARM: dts: mediatek: add MT7623 basic support")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2724807f7f upstream.
Any failure in the secure call for transferring mem ownership of mba
region to Q6 would result in reporting that the remoteproc device
is running. This is because the previous q6v5_clk_enable would have
been a success. Prevent this by updating variable 'ret' accordingly.
Cc: stable@vger.kernel.org
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e93a65857 upstream.
Intel Cannon Lake PCH has much higher 216 MHz input clock to LPSS I2C
than Sunrisepoint which uses 120 MHz. Preliminary information was that
both share the same clock rate but actual silicon implements elevated
rate for better support for 3.4 MHz high-speed I2C.
This incorrect input clock rate results too high I2C bus clock in case
ACPI doesn't provide tuned I2C timing parameters since I2C host
controller driver calculates them from input clock rate.
Fix this by using the correct rate. We still share the same 230 ns SDA
hold time value than Sunrisepoint.
Cc: stable@vger.kernel.org
Fixes: b418bbff36 ("mfd: intel-lpss: Add Intel Cannonlake PCI IDs")
Reported-by: Jian-Hong Pan <jian-hong@endlessm.com>
Reported-by: Chris Chiu <chiu@endlessm.com>
Reported-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d28b625208 upstream.
According to documentation REMAP register has to be programmed in
either DMA or PIO mode of the slice.
Move the DMA capability check below to let REMAP register be programmed
in PIO mode.
Cc: stable@vger.kernel.org # 4.3+
Fixes: 4b45efe852 ("mfd: Add support for Intel Sunrisepoint LPSS devices")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81114baa83 upstream.
Related to https://lkml.org/lkml/2018/4/8/661
Sometimes, we need to write meta data to new allocated block address,
then we will allocate a zeroed page in inner inode's address space, and
fill partial data in it, and leave other place with zero value which means
some fields are initial status.
There are two inner inodes (meta inode and node inode) setting __GFP_ZERO,
I have just checked them, for both of them, we can avoid using __GFP_ZERO,
and do initialization by ourselves to avoid unneeded/redundant zeroing
from mm.
Cc: <stable@vger.kernel.org>
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e16c4790de upstream.
This reverts commit b468620f2a.
It turns out that this broke drm on AMD platforms. Quoting Gabriel C:
"I can confirm reverting b468620f2a fixes
that issue for me.
The GPU is working fine with SME enabled.
Now with working GPU :) I can also confirm performance is back to
normal without doing any other workarounds"
Christan König analyzed it partially:
"As far as I analyzed it we now get an -ENOMEM from dma_alloc_attrs()
in drivers/gpu/drm/ttm/ttm_page_alloc_dma.c when IOMMU is enabled"
and Christoph Hellwig responded:
"I think the prime issue is that dma_direct_alloc respects the dma
mask. Which we don't need if actually using the iommu. This would be
mostly harmless exept for the the SEV bit high in the address that
makes the checks fail.
For now I'd say revert this commit for 4.17/4.18-rc and I'll look into
addressing these issues properly"
Reported-and-bisected-by: Gabriel C <nix.or.die@gmail.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Cc: Christian König <christian.koenig@amd.com>
Cc: Michel Dänzer <michel.daenzer@amd.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: stable@kernel.org # v4.17
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b12dfa124 upstream.
Fix child-node lookup during probe, which ended up searching the whole
device tree depth-first starting at the parent rather than just matching
on its children.
This would only cause trouble if the child node is missing while there
is an unrelated node named "backlight" elsewhere in the tree.
Cc: stable <stable@vger.kernel.org> # 3.7
Fixes: eebfdc17cc ("backlight: Add TPS65217 WLED driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d1cc0ec3da upstream.
Fix child-node lookup during probe, which ended up searching the whole
device tree depth-first starting at the parent rather than just matching
on its children.
To make things worse, the parent mfd node was also prematurely freed,
while the child backlight node was leaked.
Cc: stable <stable@vger.kernel.org> # 3.9
Fixes: 47ec340cb8 ("mfd: max8925: Support dt for backlight")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a9c8bb2ac upstream.
Fix child-node lookup during probe, which ended up searching the whole
device tree depth-first starting at the parent rather than just matching
on its children.
To make things worse, the parent mfd node was also prematurely freed.
Cc: stable <stable@vger.kernel.org> # 3.10
Fixes: 59eb2b5e57 ("drivers/video/backlight/as3711_bl.c: add OF support")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 353748a359 upstream.
There is potential for the size and len fields in ubifs_data_node to be
too large causing either a negative value for the length fields or an
integer overflow leading to an incorrect memory allocation. Likewise,
when the len field is small, an integer underflow may occur.
Signed-off-by: Silvio Cesare <silvio.cesare@gmail.com>
Fixes: 1e51764a3c ("UBIFS: add new flash file system")
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 781932375f upstream.
Fastmap cannot track the LEB unmap operation, therefore it can
happen that after an interrupted erasure the mapping still looks
good from Fastmap's point of view, while reading from the PEB will
cause an ECC error and confuses the upper layer.
Instead of teaching users of UBI how to deal with that, we read back
the VID header and check for errors. If the PEB is empty or shows ECC
errors we fixup the mapping and schedule the PEB for erasure.
Fixes: dbb7d2a88d ("UBI: Add fastmap core")
Cc: <stable@vger.kernel.org>
Reported-by: martin bayern <Martinbayern@outlook.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e7d801610 upstream.
Ben Hutchings pointed out that 29b7a6fa1e ("ubi: fastmap: Don't flush
fastmap work on detach") does not really fix the problem, it just
reduces the risk to hit the race window where fastmap work races against
free()'ing ubi->volumes[].
The correct approach is making sure that no more fastmap work is in
progress before we free ubi data structures.
So we cancel fastmap work right after the ubi background thread is
stopped.
By setting ubi->thread_enabled to zero we make sure that no further work
tries to wake the thread.
Fixes: 29b7a6fa1e ("ubi: fastmap: Don't flush fastmap work on detach")
Fixes: 74cdaf2400 ("UBI: Fastmap: Fix memory leaks while closing the WL sub-system")
Cc: stable@vger.kernel.org
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Cc: Martin Townsend <mtownsend1973@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a2e84c6ed upstream.
All the managed resources would be freed by the time release function
is invoked. Handling such memory in qcom_smd_edge_release() would do
bad things.
Found this issue while testing Audio usecase where the dsp is started up
and shutdown in a loop.
This patch fixes this issue by using simple kzalloc for allocating
channel->name and channel which is then freed in qcom_smd_edge_release().
Without this patch restarting a remoteproc would crash the system.
Fixes: 53e2822e56 ("rpmsg: Introduce Qualcomm SMD backend")
Cc: <stable@vger.kernel.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 011abdc9df upstream.
If "re-add" is written to the "state" file for a device
which is faulty, this has an effect similar to removing
and re-adding the device. It should take up the
same slot in the array that it previously had, and
an accelerated (e.g. bitmap-based) rebuild should happen.
The slot that "it previously had" is determined by
rdev->saved_raid_disk.
However this is not set when a device fails (only when a device
is added), and it is cleared when resync completes.
This means that "re-add" will normally work once, but may not work a
second time.
This patch includes two fixes.
1/ when a device fails, record the ->raid_disk value in
->saved_raid_disk before clearing ->raid_disk
2/ when "re-add" is written to a device for which
->saved_raid_disk is not set, fail.
I think this is suitable for stable as it can
cause re-adding a device to be forced to do a full
resync which takes a lot longer and so puts data at
more risk.
Cc: <stable@vger.kernel.org> (v4.1)
Fixes: 97f6cd39da ("md-cluster: re-add capabilities")
Signed-off-by: NeilBrown <neilb@suse.com>
Reviewed-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09018d4bd7 upstream.
clk-gate core will take bit_idx through clk_register_gate
and then do clk_gate_ops by using BIT(bit_idx), but rtc-sun6i
is passing bit_idx as BIT(bit_idx) it becomes BIT(BIT(bit_idx)
which is wrong and eventually external gate clock is not enabling.
This patch fixed by passing bit index and the original change
introduced from below commit.
"rtc: sun6i: Add support for the external oscillator gate"
(sha1: 17ecd24641)
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Fixes: 17ecd24641 ("rtc: sun6i: Add support for the external oscillator gate")
Cc: stable@vger.kernel.org
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a982e45dc1 upstream.
When a USB device is connected to the USB host port on the SAM9N12 then
you get "-62" error which seems to indicate USB replies from the device
are timing out. Based on a logic sniffer, I saw the USB bus was running
at half speed.
The PLL code uses cached MUL and DIV values which get set in set_rate()
and applied in prepare(), but the recalc_rate() function instead
queries the hardware instead of using these cached values. Therefore,
if recalc_rate() is called between a set_rate() and prepare(), the
wrong frequency is calculated and later the USB clock divider for the
SAM9N12 SOC will be configured for an incorrect clock.
In my case, the PLL hardware was set to 96 Mhz before the OHCI
driver loads, and therefore the usb clock divider was being set
to /2 even though the OHCI driver set the PLL to 48 Mhz.
As an alternative explanation, I noticed this was fixed in the past by
87e2ed338f ("clk: at91: fix recalc_rate implementation of PLL
driver") but the bug was later re-introduced by 1bdf02326b ("clk:
at91: make use of syscon/regmap internally").
Fixes: 1bdf02326b ("clk: at91: make use of syscon/regmap internally)
Cc: <stable@vger.kernel.org>
Signed-off-by: Marcin Ziemianowicz <marcin@ziemianowicz.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 72e1f23020 upstream.
Until commit 05f814402d ("clk: meson: add fdiv clock gates") we
relied on the bootloader to enable the fclk_div clock gates. It turns
out that our clock tree is incomplete at least on Meson8b (tested with
an Odroid-C1, which uses an RGMII PHY) because after the mentioned
commit Ethernet is not working anymore (no RX/TX activity can be seen).
At the same time Ethernet was still working on Meson8m2 with a RMII PHY.
Testing has shown that as soon as "fclk_div2" is disabled Ethernet stops
working on Odroid-C1. Unfortunately it's currently not clear what the
Ethernet controller IP block uses the fclk_div2 clock for. Mark the
clock as CLK_IS_CRITICAL to keep it enabled (as it's already enabled by
most bootloaders by default, which is why we didn't notice it before).
Fixes: 05f814402d ("clk: meson: add fdiv clock gates")
Cc: stable@vger.kernel.org
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce7f11a230 upstream.
Prior to this commit we would only do a "deep flush" (have nvdimm_flush()
write to each of the flush hints for a region) in response to an
msync/fsync/sync call if the nvdimm_has_cache() returned true at the time
we were setting up the request queue. This happens due to the write cache
value passed in to blk_queue_write_cache(), which then causes the block
layer to send down BIOs with REQ_FUA and REQ_PREFLUSH set. We do have a
"write_cache" sysfs entry for namespaces, i.e.:
/sys/bus/nd/devices/pfn0.1/block/pmem0/dax/write_cache
which can be used to control whether or not the kernel thinks a given
namespace has a write cache, but this didn't modify the deep flush behavior
that we set up when the driver was initialized. Instead, it only modified
whether or not DAX would flush CPU caches via dax_flush() in response to
*sync calls.
Simplify this by making the *sync deep flush always happen, regardless of
the write cache setting of a namespace. The DAX CPU cache flushing will
still be controlled the write_cache setting of the namespace.
Cc: <stable@vger.kernel.org>
Fixes: 5fdf8e5ba5 ("libnvdimm: re-enable deep flush for pmem devices via fsync()")
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 254a4cd50b upstream.
The pmem driver does not honor a forced read-only setting for very long:
$ blockdev --setro /dev/pmem0
$ blockdev --getro /dev/pmem0
1
followed by various commands like these:
$ blockdev --rereadpt /dev/pmem0
or
$ mkfs.ext4 /dev/pmem0
results in this in the kernel serial log:
nd_pmem namespace0.0: region0 read-write, marking pmem0 read-write
with the read-only setting lost:
$ blockdev --getro /dev/pmem0
0
That's from bus.c nvdimm_revalidate_disk(), which always applies the
setting from nd_region (which is initially based on the ACPI NFIT
NVDIMM state flags not_armed bit).
In contrast, commit 20bd1d026a ("scsi: sd: Keep disk read-only when
re-reading partition") fixed this issue for SCSI devices to preserve
the previous setting if it was set to read-only.
This patch modifies bus.c to preserve any previous read-only setting.
It also eliminates the kernel serial log print except for cases where
read-write is changed to read-only, so it doesn't print read-only to
read-only non-changes.
Cc: <stable@vger.kernel.org>
Fixes: 5813882094 ("libnvdimm, nfit: handle unarmed dimms, mark namespaces read-only")
Signed-off-by: Robert Elliott <elliott@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c3d20aada upstream.
That other commit introduced an inconsistency because it would trace on
ERP_FAILED for all callers of port forced reopen triggers (not just
terminate_rport_io), but it would not trace on ERP_FAILED for all callers of
other ERP triggers such as adapter, port regular, LUN.
Therefore, generalize that other commit. zfcp_erp_action_enqueue() already
had two early outs which re-used the one zfcp_dbf_rec_trig() call. All ERP
trigger functions finally run through zfcp_erp_action_enqueue(). So move
the special handling for ZFCP_STATUS_COMMON_ERP_FAILED into
zfcp_erp_action_enqueue() and add another early out with new trace marker
for pseudo ERP need in this case. This removes all early returns from all
ERP trigger functions so we always end up at zfcp_dbf_rec_trig().
Example trace record formatted with zfcpdbf from s390-tools:
Timestamp : ...
Area : REC
Subarea : 00
Level : 1
Exception : -
CPU ID : ..
Caller : 0x...
Record ID : 1 ZFCP_DBF_REC_TRIG
Tag : .......
LUN : 0x...
WWPN : 0x...
D_ID : 0x...
Adapter status : 0x...
Port status : 0x...
LUN status : 0x...
Ready count : 0x...
Running count : 0x...
ERP want : 0x0. ZFCP_ERP_ACTION_REOPEN_...
ERP need : 0xe0 ZFCP_ERP_ACTION_FAILED
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Cc: <stable@vger.kernel.org> #2.6.38+
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d70aab5592 upstream.
For problem determination we always want to see when we were invoked on the
terminate_rport_io callback whether we perform something or not.
Temporal event sequence of interest with a long fast_io_fail_tmo of 27 sec:
loose remote port
t workqueue
[s] zfcp_q_<dev> IRQ zfcperp<dev>
=== ================== =================== ============================
0 recv RSCN
q p.test_link_work
block rport
start fast_io_fail_tmo
send ADISC ELS
4 recv ADISC fail
block zfcp_port
port forced reopen
send open port
12 recv open port fail
q p.gid_pn_work
zfcp_erp_wakeup
(zfcp_erp_wait would return)
GID_PN fail
Before this point, we got a SCSI trace with tag "sctrpi1" on fast_io_fail,
e.g. with the typical 5 sec setting.
port.status |= ERP_FAILED
If fast_io_fail_tmo triggers after this point, we missed a SCSI trace.
workqueue
fc_dl_<host>
==================
27 fc_timeout_fail_rport_io
fc_terminate_rport_io
zfcp_scsi_terminate_rport_io
zfcp_erp_port_forced_reopen
_zfcp_erp_port_forced_reopen
if (port.status & ERP_FAILED)
return;
Therefore, write a trace before above early return.
Example trace record formatted with zfcpdbf from s390-tools:
Timestamp : ...
Area : REC
Subarea : 00
Level : 1
Exception : -
CPU ID : ..
Caller : 0x...
Record ID : 1 ZFCP_DBF_REC_TRIG
Tag : sctrpi1 SCSI terminate rport I/O
LUN : 0xffffffffffffffff none (invalid)
WWPN : 0x<wwpn>
D_ID : 0x<n_port_id>
Adapter status : 0x...
Port status : 0x...
LUN status : 0x00000000 none (invalid)
Ready count : 0x...
Running count : 0x...
ERP want : 0x03 ZFCP_ERP_ACTION_REOPEN_PORT_FORCED
ERP need : 0xe0 ZFCP_ERP_ACTION_FAILED
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Cc: <stable@vger.kernel.org> #2.6.38+
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 96d9270499 upstream.
get_device() and its internally used kobject_get() only return NULL if they
get passed NULL as argument. zfcp_get_port_by_wwpn() loops over
adapter->port_list so the iteration variable port is always non-NULL.
Struct device is embedded in struct zfcp_port so &port->dev is always
non-NULL. This is the argument to get_device(). However, if we get an
fc_rport in terminate_rport_io() for which we cannot find a match within
zfcp_get_port_by_wwpn(), the latter can return NULL. v2.6.30 commit
70932935b6 ("[SCSI] zfcp: Fix oops when port disappears") introduced an
early return without adding a trace record for this case. Even if we don't
need recovery in this case, for debugging we should still see that our
callback was invoked originally by scsi_transport_fc.
Example trace record formatted with zfcpdbf from s390-tools:
Timestamp : ...
Area : REC
Subarea : 00
Level : 1
Exception : -
CPU ID : ..
Caller : 0x...
Record ID : 1
Tag : sctrpin SCSI terminate rport I/O, no zfcp port
LUN : 0xffffffffffffffff none (invalid)
WWPN : 0x<wwpn> WWPN
D_ID : 0x<n_port_id> N_Port-ID
Adapter status : 0x...
Port status : 0xffffffff unknown (-1)
LUN status : 0x00000000 none (invalid)
Ready count : 0x...
Running count : 0x...
ERP want : 0x03 ZFCP_ERP_ACTION_REOPEN_PORT_FORCED
ERP need : 0xc0 ZFCP_ERP_ACTION_NONE
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Fixes: 70932935b6 ("[SCSI] zfcp: Fix oops when port disappears")
Cc: <stable@vger.kernel.org> #2.6.38+
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 512857a795 upstream.
If a SCSI device is deleted during scsi_eh host reset, we cannot get a
reference to the SCSI device anymore since scsi_device_get returns !=0 by
design. Assuming the recovery of adapter and port(s) was successful,
zfcp_erp_strategy_followup_success() attempts to trigger a LUN reset for the
half-gone SCSI device. Unfortunately, it causes the following confusing
trace record which states that zfcp will do a LUN recovery as "ERP need" is
ZFCP_ERP_ACTION_REOPEN_LUN == 1 and equals "ERP want".
Old example trace record formatted with zfcpdbf from s390-tools:
Tag: : ersfs_3 ERP, trigger, unit reopen, port reopen succeeded
LUN : 0x<FCP_LUN>
WWPN : 0x<WWPN>
D_ID : 0x<N_Port-ID>
Adapter status : 0x5400050b
Port status : 0x54000001
LUN status : 0x40000000 ZFCP_STATUS_COMMON_RUNNING
but not ZFCP_STATUS_COMMON_UNBLOCKED as it
was closed on close part of adapter reopen
ERP want : 0x01
ERP need : 0x01 misleading
However, zfcp_erp_setup_act() returns NULL as it cannot get the reference.
Hence, zfcp_erp_action_enqueue() takes an early goto out and _NO_ recovery
actually happens.
We always do want the recovery trigger trace record even if no erp_action
could be enqueued as in this case. For other cases where we did not enqueue
an erp_action, 'need' has always been zero to indicate this. In order to
indicate above goto out, introduce an eyecatcher "flag" to mark the "ERP
need" as 'not needed' but still keep the information which erp_action type,
that zfcp_erp_required_act() had decided upon, is needed. 0xc_ is chosen to
be visibly different from 0x0_ in "ERP want".
New example trace record formatted with zfcpdbf from s390-tools:
Tag: : ersfs_3 ERP, trigger, unit reopen, port reopen succeeded
LUN : 0x<FCP_LUN>
WWPN : 0x<WWPN>
D_ID : 0x<N_Port-ID>
Adapter status : 0x5400050b
Port status : 0x54000001
LUN status : 0x40000000
ERP want : 0x01
ERP need : 0xc1 would need LUN ERP, but no action set up
^
Before v2.6.38 commit ae0904f60f ("[SCSI] zfcp: Redesign of the debug
tracing for recovery actions.") we could detect this case because the
"erp_action" field in the trace was NULL. The rework removed erp_action as
argument and field from the trace.
This patch here is for tracing. A fix to allow LUN recovery in the case at
hand is a topic for a separate patch.
See also commit fdbd1c5e27 ("[SCSI] zfcp: Allow running unit/LUN shutdown
without acquiring reference") for a similar case and background info.
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Fixes: ae0904f60f ("[SCSI] zfcp: Redesign of the debug tracing for recovery actions.")
Cc: <stable@vger.kernel.org> #2.6.38+
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81979ae63e upstream.
We already have a SCSI trace for the end of abort and scsi_eh TMF. Due to
zfcp_erp_wait() and fc_block_scsi_eh() time can pass between the start of
our eh callback and an actual send/recv of an abort / TMF request. In order
to see the temporal sequence including any abort / TMF send retries, add a
trace before the above two blocking functions. This supports problem
determination with scsi_eh and parallel zfcp ERP.
No need to explicitly trace the beginning of our eh callback, since we
typically can send an abort / TMF and see its HBA response (in the worst
case, it's a pseudo response on dismiss all of adapter recovery, e.g. due to
an FSF request timeout [fsrth_1] of the abort / TMF). If we cannot send, we
now get a trace record for the first "abrt_wt" or "[lt]r_wait" which denotes
almost the beginning of the callback.
No need to explicitly trace the wakeup after the above two blocking
functions because the next retry loop causes another trace in any case and
that is sufficient.
Example trace records formatted with zfcpdbf from s390-tools:
Timestamp : ...
Area : SCSI
Subarea : 00
Level : 1
Exception : -
CPU ID : ..
Caller : 0x...
Record ID : 1
Tag : abrt_wt abort, before zfcp_erp_wait()
Request ID : 0x0000000000000000 none (invalid)
SCSI ID : 0x<scsi_id>
SCSI LUN : 0x<scsi_lun>
SCSI LUN high : 0x<scsi_lun_high>
SCSI result : 0x<scsi_result_of_cmd_to_be_aborted>
SCSI retries : 0x<retries_of_cmd_to_be_aborted>
SCSI allowed : 0x<allowed_retries_of_cmd_to_be_aborted>
SCSI scribble : 0x<req_id_of_cmd_to_be_aborted>
SCSI opcode : <CDB_of_cmd_to_be_aborted>
FCP rsp inf cod: 0x.. none (invalid)
FCP rsp IU : ... none (invalid)
Timestamp : ...
Area : SCSI
Subarea : 00
Level : 1
Exception : -
CPU ID : ..
Caller : 0x...
Record ID : 1
Tag : lr_wait LUN reset, before zfcp_erp_wait()
Request ID : 0x0000000000000000 none (invalid)
SCSI ID : 0x<scsi_id>
SCSI LUN : 0x<scsi_lun>
SCSI LUN high : 0x<scsi_lun_high>
SCSI result : 0x... unrelated
SCSI retries : 0x.. unrelated
SCSI allowed : 0x.. unrelated
SCSI scribble : 0x... unrelated
SCSI opcode : ... unrelated
FCP rsp inf cod: 0x.. none (invalid)
FCP rsp IU : ... none (invalid)
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Fixes: 63caf367e1 ("[SCSI] zfcp: Improve reliability of SCSI eh handlers in zfcp")
Fixes: af4de36d91 ("[SCSI] zfcp: Block scsi_eh thread for rport state BLOCKED")
Cc: <stable@vger.kernel.org> #2.6.38+
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df30781699 upstream.
For problem determination we need to see whether and why we were successful
or not. This allows deduction of scsi_eh escalation.
Example trace record formatted with zfcpdbf from s390-tools:
Timestamp : ...
Area : SCSI
Subarea : 00
Level : 1
Exception : -
CPU ID : ..
Caller : 0x...
Record ID : 1
Tag : schrh_r SCSI host reset handler result
Request ID : 0x0000000000000000 none (invalid)
SCSI ID : 0xffffffff none (invalid)
SCSI LUN : 0xffffffff none (invalid)
SCSI LUN high : 0xffffffff none (invalid)
SCSI result : 0x00002002 field re-used for midlayer value: SUCCESS
or in other cases: 0x2009 == FAST_IO_FAIL
SCSI retries : 0xff none (invalid)
SCSI allowed : 0xff none (invalid)
SCSI scribble : 0xffffffffffffffff none (invalid)
SCSI opcode : ffffffff ffffffff ffffffff ffffffff none (invalid)
FCP rsp inf cod: 0xff none (invalid)
FCP rsp IU : 00000000 00000000 00000000 00000000 none (invalid)
00000000 00000000
v2.6.35 commit a1dbfddd02 ("[SCSI] zfcp: Pass return code from
fc_block_scsi_eh to scsi eh") introduced the first return with something
other than the previously hardcoded single SUCCESS return path.
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Fixes: a1dbfddd02 ("[SCSI] zfcp: Pass return code from fc_block_scsi_eh to scsi eh")
Cc: <stable@vger.kernel.org> #2.6.38+
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 49d7bd3681 upstream.
The patch reverts changes done in qlt_schedule_sess_for_deletion() to
avoid spinlock recursion sess->vha->work_lock should be used instead
of ha->tgt.sess_lock, that can be locked in callers: qlt_reset() or
qlt_handle_login()
[mkp: roll in build warning reported by sfr]
Fixes: 1c6cacf4ea ("scsi: qla2xxx: Fixup locking for session deletion")
Cc: <stable@vger.kernel.org> #v4.17
Signed-off-by: Mikhail Malygin <m.malygin@yadro.com>
Reported-by: Mikhail Malygin <m.malygin@yadro.com>
Tested-by: Mikhail Malygin <m.malygin@yadro.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3cedc8797b upstream.
Some newer target uses "Status Qualifier" response in a returned "Busy
Status". This new response code of 0x4001, which is "Scope" bits,
translates to "Affects all units accessible by target". Due to this new
value returned in the Scope bits, driver was using that value as timeout
value which resulted into driver waiting for 27min timeout.
This patch masks off this Scope bits so that driver does not use this
value as retry delay time.
Cc: <stable@vger.kernel.org>
Signed-off-by: Anil Gurumurthy <anil.gurumurthy@cavium.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 413c2f3348 upstream.
This patch prevents driver from setting lower default speed of 1 GB/sec,
if the switch does not support Get Port Speed Capabilities (GPSC)
command. Setting this default speed results into much lower write
performance for large sequential WRITE. This patch modifies driver to
check for gpsc_supported flags and prevents driver from issuing
MBC_SET_PORT_PARAM (001Ah) to set default speed of 1 GB/sec. If driver
does not send this mailbox command, firmware assumes maximum supported
link speed and will operate at the max speed.
Cc: stable@vger.kernel.org
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reported-by: Eda Zhou <ezhou@redhat.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Tested-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0d98ba8d70 upstream.
'Commit cc27b735ad ("PCI/portdrv: Turn off PCIe services during
shutdown")' has been added to kernel to shutdown pending PCIe port service
interrupts during reboot so that a newly started kexec kernel wouldn't
observe pending interrupts.
pcie_port_device_remove() is disabling the root port and switches by
calling pci_disable_device() after all PCIe service drivers are shutdown.
This has been found to cause crashes on HP DL360 Gen9 machines during
reboot due to hpsa driver not clearing the bus master bit during the
shutdown procedure by calling pci_disable_device().
Disable device as part of the shutdown sequence.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199779
Fixes: cc27b735ad ("PCI/portdrv: Turn off PCIe services during shutdown")
Cc: stable@vger.kernel.org
Reported-by: Ryan Finnie <ryan@finnie.org>
Tested-by: Don Brace <don.brace@microsemi.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 52ab9768f7 upstream.
Since commit 80c49563e2 ("scsi: scsi_debug: implement IMMED bit") there
are long delays in F_SYNC_DELAY and F_SSU_DELAY. This can cause a memory
leak in schedule_resp(), which can be invoked while unloading the
scsi_debug module: free_all_queued() had already freed all sd_dp and
schedule_resp will alloc a new one, which will never get freed. Here's the
kmemleak report while running xfstests generic/350:
unreferenced object 0xffff88007d752b00 (size 128):
comm "rmmod", pid 26940, jiffies 4295816945 (age 7.588s)
hex dump (first 32 bytes):
00 2b 75 7d 00 88 ff ff 00 00 00 00 00 00 00 00 .+u}............
00 00 00 00 00 00 00 00 8e 31 a2 34 5f 03 00 00 .........1.4_...
backtrace:
[<000000002abd83d0>] 0xffffffffa000705e
[<000000004c063fda>] scsi_dispatch_cmd+0xc7/0x1a0
[<000000000c119a00>] scsi_request_fn+0x251/0x550
[<000000009de0c736>] __blk_run_queue+0x3f/0x60
[<000000001c4453c8>] blk_execute_rq_nowait+0x98/0xd0
[<00000000d17ec79f>] blk_execute_rq+0x3a/0x50
[<00000000a7654b6e>] scsi_execute+0x113/0x250
[<00000000fd78f7cd>] sd_sync_cache+0x95/0x160
[<0000000024dacb14>] sd_shutdown+0x9b/0xd0
[<00000000e9101710>] sd_remove+0x5f/0xb0
[<00000000c43f0d63>] device_release_driver_internal+0x13c/0x1f0
[<00000000e8ad57b6>] bus_remove_device+0xe9/0x160
[<00000000713a7b8a>] device_del+0x120/0x320
[<00000000e5db670c>] __scsi_remove_device+0x115/0x150
[<00000000eccbef30>] scsi_forget_host+0x20/0x60
[<00000000cd5a0738>] scsi_remove_host+0x6d/0x120
Cc: stable@vger.kernel.org # v4.17+
Signed-off-by: Luis Henriques <lhenriques@suse.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a9b6de77b1 upstream.
get_user_pages_fast() for device pages is missing the typical validation
that all page references have been taken while the mapping was valid.
Without this validation truncate operations can not reliably coordinate
against new page reference events like O_DIRECT.
Cc: <stable@vger.kernel.org>
Fixes: 3565fce3a6 ("mm, x86: get_user_pages() for dax mappings")
Reported-by: Jan Kara <jack@suse.cz>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a5b45383c upstream.
Use 'devm_iio_kfifo_allocate()' instead of 'iio_kfifo_allocate()' in order
to simplify code and avoid a memory leak in an error path in
'sca3000_probe()'. A call to 'sca3000_unconfigure_ring()' was missing.
Sent via the next merge window as unimportant bug and there are
other patches dependent on it.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7eb6b35d93 upstream.
In the current state, these attributes are broken, because they are
registered already, and the kernel throws a warning.
The first registration happens via the `IIO_CHAN_INFO_SAMP_FREQ` flag from
the `ad_sigma_delta` driver.
In this commit these attrs are removed, and in the following the
IIO_CHAN_INFO_SAMP_FREQ behavior will be implemented, which replaces these
hooks.
This is done to make things a bit easier to review as there is a bit of
overlap in the patch if it's done all at once.
Fixes: a13e831fca ("staging: iio: ad7192: implement IIO_CHAN_INFO_SAMP_FREQ")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c5b4a50b74 upstream.
If we failed during a rename exchange operation after starting/joining a
transaction, we would end up replacing the return value, stored in the
local 'ret' variable, with the return value from btrfs_end_transaction().
So this could end up returning 0 (success) to user space despite the
operation having failed and aborted the transaction, because if there are
multiple tasks having a reference on the transaction at the time
btrfs_end_transaction() is called by the rename exchange, that function
returns 0 (otherwise it returns -EIO and not the original error value).
So fix this by not overwriting the return value on error after getting
a transaction handle.
Fixes: cdd1fedf82 ("btrfs: add support for RENAME_EXCHANGE and RENAME_WHITEOUT")
CC: stable@vger.kernel.org # 4.9+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b65c32ec5a upstream.
The signatureValue field of a X.509 certificate is encoded as a BIT STRING.
For RSA signatures this BIT STRING is of so-called primitive subtype, which
contains a u8 prefix indicating a count of unused bits in the encoding.
We have to strip this prefix from signature data, just as we already do for
key data in x509_extract_key_data() function.
This wasn't noticed earlier because this prefix byte is zero for RSA key
sizes divisible by 8. Since BIT STRING is a big-endian encoding adding zero
prefixes has no bearing on its value.
The signature length, however was incorrect, which is a problem for RSA
implementations that need it to be exactly correct (like AMD CCP).
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Fixes: c26fd69fa0 ("X.509: Add a crypto key parser for binary (DER) X.509 certificates")
Cc: stable@vger.kernel.org
Signed-off-by: James Morris <james.morris@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit abcbcb80cd upstream.
For the common cases where 1000 is a multiple of HZ, or HZ is a multiple of
1000, jiffies_to_msecs() never returns zero when passed a non-zero time
period.
However, if HZ > 1000 and not an integer multiple of 1000 (e.g. 1024 or
1200, as used on alpha and DECstation), jiffies_to_msecs() may return zero
for small non-zero time periods. This may break code that relies on
receiving back a non-zero value.
jiffies_to_usecs() does not need such a fix: one jiffy can only be less
than one µs if HZ > 1000000, and such large values of HZ are already
rejected at build time, twice:
- include/linux/jiffies.h does #error if HZ >= 12288,
- kernel/time/time.c has BUILD_BUG_ON(HZ > USEC_PER_SEC).
Broken since forever.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-alpha@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20180622143357.7495-1-geert@linux-m68k.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff7c991714 upstream.
When scaling max/min settings are changed, internally they are converted
to a ratio using the max turbo 1 core turbo frequency. This works fine
when 1 core max is same irrespective of the core. But under Turbo 3.0,
this will not be the case. For example:
Core 0: max turbo pstate: 43 (4.3GHz)
Core 1: max turbo pstate: 45 (4.5GHz)
In this case 1 core turbo ratio will be maximum of all, so it will be
45 (4.5GHz). Suppose scaling max is set to 4GHz (ratio 40) for all cores
,then on core one it will be
= max_state * policy->max / max_freq;
= 43 * (4000000/4500000) = 38 (3.8GHz)
= 38
which is 200MHz less than the desired.
On core2, it will be correctly set to ratio 40 (4GHz). Same holds true
for scaling min frequency limit. So this requires usage of correct turbo
max frequency for core one, which in this case is 4.3GHz. So we need to
adjust per CPU cpu->pstate.turbo_freq using the maximum HWP ratio of that
core.
This change uses the HWP capability of a core to adjust max turbo
frequency. But since Broadwell HWP doesn't use ratios in the HWP
capabilities, we have to use legacy max 1 core turbo ratio. This is not
a problem as the HWP capabilities don't differ among cores in Broadwell.
We need to check for non Broadwell CPU model for applying this change,
though.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: 4.6+ <stable@vger.kernel.org> # 4.6+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bc3322bc16 upstream.
Commit b89405b610 ("pinctrl: devicetree: Fix dt_to_map_one_config
handling of hogs") causes the pinctrl hog pins to not get initialized
on i.MX platforms leaving them with the IOMUX settings untouched.
This causes several regressions on i.MX such as:
- OV5640 camera driver can not be probed anymore on imx6qdl-sabresd
because the camera clock pin is in a pinctrl_hog group and since
its pinctrl initialization is skipped, the camera clock is kept
in GPIO functionality instead of CLK_CKO function.
- Audio stopped working on imx6qdl-wandboard and imx53-qsb for
the same reason.
Richard Fitzgerald explains the problem:
"I see the bug. If the hog node isn't a 1st level child of the pinctrl
parent node it will go around the for(;;) loop again but on the first
pass I overwrite pctldev with the result of
get_pinctrl_dev_from_of_node() so it doesn't point to the pinctrl driver
any more."
Fix the issue by stashing the original pctldev so it doesn't
get overwritten.
Fixes: b89405b610 ("pinctrl: devicetree: Fix dt_to_map_one_config handling of hogs")
Cc: <stable@vger.kernel.org>
Reported-by: Mika Penttilä <mika.penttila@nextfour.com>
Reported-by: Steve Longerbeam <slongerbeam@gmail.com>
Suggested-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5cf9a338db upstream.
All banks with GPIO interrupts should be at beginning of bank array and
without any other types of banks between them. This order is expected
by exynos_eint_gpio_irq, when doing interrupt group to bank translation.
Otherwise, kernel NULL pointer dereference would happen when trying to
handle interrupt, due to wrong bank being looked up. Observed on
s5pv210, when trying to handle gpj0 interrupt, where kernel was mapping
it to gpi bank.
Cc: stable@vger.kernel.org
Fixes: 023e06dfa6 ("pinctrl: exynos: add exynos5410 SoC specific data")
Fixes: 608a26a7bc ("pinctrl: Add s5pv210 support to pinctrl-exynos)
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Reviewed-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 702d1e81fe upstream.
Until now, if we found spurious irq in irq_handler, we only updated the
status in register but not the status in the code. Due to this the system
will got stuck dues to the infinite loop
[gregory.clement@bootlin.com: update comment and add fix and stable tags]
Fixes: 30ac0d3b07 ("pinctrl: armada-37xx: Add edge both type gpio irq support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Terry Zhou <bjzhou@marvell.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5b903fba9 upstream.
Having the CHARLCD Kconfig symbol between "menuconfig AUXDISPLAY"
and "if AUXDISPLAY" breaks the AUXDISPLAY submenus, so move the
CHARLCD Kconfig symbol near the end of the file so that the menu
display is continuous.
Also include ARM_CHARLCD inside of the if AUXDISPLAY/endif block.
Geert says that it should be there.
Fixes: 39f8ea4672 ("auxdisplay: charlcd: Extract character LCD core from misc/panel")
Cc: stable@vger.kernel.org # v4.12
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3374c545c2 upstream.
When distributing extra bus number space to hotplug bridges for future
extension, we don't account for the fact that there might be non-hotplug
bridges on the bus after the hotplug bridges. For example:
01:00.0 --+- 02:00.0 (HotPlug-) -- Thunderbolt host controller
+- 02:01.0 (HotPlug+)
\- 02:02.0 (HotPlug-) -- xHCI host controller
pci_scan_child_bus_extend() is supposed to distribute the remaining bus
numbers to the hotplug bridge at 02:01.0, but only after accounting for all
bridges on bus 02. Since we don't check whether there's another
non-hotplug bridge after the hotplug bridge 02:01.0, it may not leave space
for the non-hotplug bridge:
pci 0000:00:1b.0: PCI bridge to [bus 01-39] (Root Port)
pci 0000:01:00.0: PCI bridge to [bus 02-39]
...
pci 0000:02:00.0: PCI bridge to [bus 03]
pci 0000:02:01.0: PCI bridge to [bus 04]
pci_bus 0000:04: [bus 04-39] extended by 0x35
pci_bus 0000:04: bus scan returning with max=39
pci_bus 0000:04: busn_res: [bus 04-39] end is updated to 39
pci 0000:02:02.0: scanning [bus 00-00] behind bridge, pass 1
pci_bus 0000:3a: scanning bus
pci_bus 0000:3a: bus scan returning with max=3a
pci_bus 0000:3a: busn_res: [bus 3a] end is updated to 3a
pci_bus 0000:3a: [bus 3a] partially hidden behind bridge 0000:02 [bus 02-39]
pci_bus 0000:3a: [bus 3a] partially hidden behind bridge 0000:01 [bus 01-39]
pci_bus 0000:02: bus scan returning with max=3a
pci_bus 0000:02: busn_res: [bus 02-39] end can not be updated to 3a
The resulting 'lspci -t' output looks like this:
+-1b.0-[01-39]----00.0-[02-3a]--+-00.0-[03]----00.0
^^ +-01.0-[04-39]--
\-02.0-[3a]----00.0
^^
The xHCI host controller behind 02:02.0 is not usable because it would have
to be assigned bus 3a, which is not accessible through 00:1b.0.
To fix this, reserve at least one bus for each bridge while scanning
already configured bridges. Then use this information in the second
scan to correct the available extra bus space for hotplug bridges.
After this change the 'lspci -t' output is what is expected:
+-1b.0-[01-39]----00.0-[02-39]--+-00.0-[03]----00.0
+-01.0-[04-38]--
\-02.0-[39]----00.0
The xHCI controller is now on bus 39, where it is usable.
Fixes: 1c02ea8100 ("PCI: Distribute available buses to hotplug-capable bridges")
Reported-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 13c65840fe upstream.
After a suspend/resume cycle the Presence Detect or Data Link Layer Status
Changed bits might be set. If we don't clear them those events will not
fire anymore and nothing happens for instance when a device is now
hot-unplugged.
Fix this by clearing those bits in a newly introduced function
pcie_reenable_notification(). This should be fine because immediately
after, we check if the adapter is still present by reading directly from
the status register.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 29927dfb7f upstream.
When Linux runs as a guest VM in Hyper-V and Hyper-V adds the virtual PCI
bus to the guest, Hyper-V always provides unique PCI domain.
commit 4a9b0933bd ("PCI: hv: Use device serial number as PCI domain")
overrode unique domain with the serial number of the first device added to
the virtual PCI bus.
The reason for that patch was to have a consistent and short name for the
device, but Hyper-V doesn't provide unique serial numbers. Using non-unique
serial numbers as domain IDs leads to duplicate device addresses, which
causes PCI bus registration to fail.
commit 0c195567a8 ("netvsc: transparent VF management") avoids the need
for commit 4a9b0933bd ("PCI: hv: Use device serial number as PCI
domain"). When scripts were used to configure VF devices, the name of
the VF needed to be consistent and short, but with commit 0c195567a8
("netvsc: transparent VF management") all the setup is done in the kernel,
and we do not need to maintain consistent name.
Revert commit 4a9b0933bd ("PCI: hv: Use device serial number as PCI
domain") so we can reliably support multiple devices being assigned to
a guest.
Tag the patch for stable kernels containing commit 0c195567a8
("netvsc: transparent VF management").
Fixes: 4a9b0933bd ("PCI: hv: Use device serial number as PCI domain")
Signed-off-by: Sridhar Pitchai <sridhar.pitchai@microsoft.com>
[lorenzo.pieralisi@arm.com: trimmed commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org # v4.14+
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e76e56823a upstream.
This commit fixes incorrect setting of reset bits for PCI/VGA and
PECI modules.
1. Reset bit for PCI/VGA is 8.
2. PECI reset bit is missing so added bit 10 as its reset bit.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Fixes: 15ed8ce5f8 ("clk: aspeed: Register gated clocks")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a027b47db upstream.
The erratum and workaround are described by BCM5300X-ES300-RDS.pdf as
below.
R10: PCIe Transactions Periodically Fail
Description: The BCM5300X PCIe does not maintain transaction ordering.
This may cause PCIe transaction failure.
Fix Comment: Add a dummy PCIe configuration read after a PCIe
configuration write to ensure PCIe configuration access
ordering. Set ES bit of CP0 configu7 register to enable
sync function so that the sync instruction is functional.
Resolution: hndpci.c: extpci_write_config()
hndmips.c: si_mips_init()
mipsinc.h CONF7_ES
This is fixed by the CFE MIPS bcmsi chipset driver also for BCM47XX.
Also the dummy PCIe configuration read is already implemented in the
Linux BCMA driver.
Enable ExternalSync in Config7 when CONFIG_BCMA_DRIVER_PCI_HOSTMODE=y
too so that the sync instruction is externalised.
Signed-off-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp>
Reviewed-by: Paul Burton <paul.burton@mips.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/19461/
Signed-off-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0cd8116f17 upstream.
The "sector is in requested range" test used to determine whether
sectors should be re-locked or not is done on a variable that is reset
everytime we cross a chip boundary, which can lead to some blocks being
re-locked while the caller expect them to be unlocked.
Fix the check to make sure this cannot happen.
Fixes: 1648eaaa15 ("mtd: cfi_cmdset_0002: Support Persistent Protection Bits (PPB) locking")
Cc: stable@vger.kernel.org
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5fdfc3dbad upstream.
cfi_ppb_unlock() tries to relock all sectors that were locked before
unlocking the whole chip.
This locking used the chip start address + the FULL offset from the
first flash chip, thereby forming an illegal address. Fix that by using
the chip offset(adr).
Fixes: 1648eaaa15 ("mtd: cfi_cmdset_0002: Support Persistent Protection Bits (PPB) locking")
Cc: stable@vger.kernel.org
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f77f244d8 upstream.
The v21 version of the NAND flash controller contains a Spare Area Size
Register (SPAS) at offset 0x10. Its setting defaults to the maximum
spare area size of 218 bytes. The size that is set in this register is
used by the controller when it calculates the ECC bytes internally in
hardware.
Usually, this register is updated from settings in the IIM fuses when
the system is booting from NAND flash. For other boot media, however,
the SPAS register remains at the default setting, which may not work for
the particular flash chip on the board. The same goes for flash chips
whose configuration cannot be set in the IIM fuses (e.g. chips with 2k
sector size and 128 bytes spare area size can't be configured in the IIM
fuses on imx25 systems).
Set the SPAS register explicitly during the preset operation. Derive the
register value from mtd->oobsize that was detected during probe by
decoding the flash chip's ID bytes.
While at it, rename the define for the spare area register's offset to
NFC_V21_RSLTSPARE_AREA. The register at offset 0x10 on v1 controllers is
different from the register on v21 controllers.
Fixes: d484018 ("mtd: mxc_nand: set NFC registers after reset")
Cc: stable@vger.kernel.org
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9893e6fa9 upstream.
Positive return value from read_oob() is making false BAD
blocks. For some of the NAND controllers, OOB bytes will be
protected with ECC and read_oob() will return number of bitflips.
If there is any bitflip in ECC protected OOB bytes for BAD block
status page, then that block is getting treated as BAD.
Fixes: c120e75e0e ("mtd: nand: use read_oob() instead of cmdfunc() for bad block check")
Cc: <stable@vger.kernel.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f6e698604 upstream.
Since commit 1bb8866677 ("mtd: nand: denali: handle timing parameters
by setup_data_interface()"), denali_dt.c gets the clock rate from the
clock driver. The driver expects the frequency of the bus interface
clock, whereas the clock driver of SOCFPGA provides the core clock.
Thus, the setup_data_interface() hook calculates timing parameters
based on a wrong frequency.
To make it work without relying on the clock driver, hard-code the clock
frequency, 200MHz. This is fine for existing DT of UniPhier, and also
fixes the issue of SOCFPGA because both platforms use 200 MHz for the
bus interface clock.
Fixes: 1bb8866677 ("mtd: nand: denali: handle timing parameters by setup_data_interface()")
Cc: linux-stable <stable@vger.kernel.org> #4.14+
Reported-by: Philipp Rosenberger <p.rosenberger@linutronix.de>
Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 782d1967d0 upstream.
The ONFI spec clearly says that FAIL bit is only valid for PROGRAM,
ERASE and READ-with-on-die-ECC operations, and should be ignored
otherwise.
It seems that checking it after sending a SET_FEATURES is a bad idea
because a previous READ, PROGRAM or ERASE op may have failed, and
depending on the implementation, the FAIL bit is not cleared until a
new READ, PROGRAM or ERASE is started.
This leads to ->set_features() returning -EIO while it actually worked,
which can sometimes stop a batch of READ/PROGRAM ops.
Note that we only fix the ->exec_op() path here, because some drivers
are abusing the NAND_STATUS_FAIL flag in their ->waitfunc()
implementation to propagate other kind of errors, like
wait-ready-timeout or controller-related errors. Let's not try to fix
those drivers since they worked fine so far.
Fixes: 8878b126df ("mtd: nand: add ->exec_op() implementation")
Cc: stable@vger.kernel.org
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8f688ec43 upstream.
The use of -EAGAIN in rpcrdma_convert_iovs() is a latent bug: the
transport never calls xprt_write_space() when more pages become
available. -ENOBUFS will trigger the correct "delay briefly and call
again" logic.
Fixes: 7a89f9c626 ("xprtrdma: Honor ->send_request API contract")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Cc: stable@vger.kernel.org # 4.8+
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1eb9364ce8 upstream.
During disassociation the ucontext will become NULL, however due to how
the SRCU locking works the ucontext must only be examined after looking
at the ib_dev, which governs the RCU control flow.
With the wrong ordering userspace will see EINVAL instead of EIO for a
disassociated uverbs FD, which breaks rdma-core.
Cc: stable@vger.kernel.org
Fixes: 491d5c6a30 ("RDMA/uverbs: Move uncontext check before SRCU read lock")
Reported-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1bc0299d97 upstream.
The following code fails to allocate a buffer for the
tail address that the hardware DMAs into when the user
context DMA_RTAIL is set.
if (HFI1_CAP_KGET_MASK(rcd->flags, DMA_RTAIL)) {
rcd->rcvhdrtail_kvaddr = dma_zalloc_coherent(
&dd->pcidev->dev, PAGE_SIZE, &dma_hdrqtail,
gfp_flags);
if (!rcd->rcvhdrtail_kvaddr)
goto bail_free;
rcd->rcvhdrqtailaddr_dma = dma_hdrqtail;
}
So the rcvhdrtail_kvaddr would then be NULL.
The mmap logic fails to check for a NULL rcvhdrtail_kvaddr.
The fix is to test for both user and kernel DMA_TAIL options
during the allocation as well as testing for a NULL
rcvhdrtail_kvaddr during the mmap processing.
Additionally, all downstream testing of the capmask for DMA_RTAIL
have been eliminated in favor of testing rcvhdrtail_kvaddr.
Cc: <stable@vger.kernel.org> # 4.9.x
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit af8aab7137 upstream.
All threads queuing CQ entries on different CQs are unnecessarily
synchronized by a spin lock to check if the CQ kthread worker hasn't
been destroyed before queuing an CQ entry.
The lock used in 6efaf10f16 ("IB/rdmavt: Avoid queuing work into a
destroyed cq kthread worker") is a device global lock and will have
poor performance at scale as completions are entered from a large
number of CPUs.
Convert to use RCU where the read side of RCU is rvt_cq_enter() to
determine that the worker is alive prior to triggering the
completion event.
Apply write side RCU semantics in rvt_driver_cq_init() and
rvt_cq_exit().
Fixes: 6efaf10f16 ("IB/rdmavt: Avoid queuing work into a destroyed cq kthread worker")
Cc: <stable@vger.kernel.org> # 4.14.x
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a93a0a3111 upstream.
User send context integrity bits are cleared before the context is
disabled. If the send context is still processing data, any packets
that need those integrity bits will cause an error and halt the send
context.
During the disable handling, the driver waits for the context to drain.
If the context is halted, the driver will eventually timeout because
the context won't drain and then incorrectly bounce the link.
Reorder the bit clearing and the context disable.
Examine the software state and send context status as well as the
egress status to determine if a send context is in the halted state.
Promote the check macros to static functions for consistency with the
new check and to follow kernel style.
Remove an unused define that refers to the egress timeout.
Cc: <stable@vger.kernel.org> # 4.9.x
Reviewed-by: Mitko Haralanov <mitko.haralanov@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b74a83cf5 upstream.
On fatal error the driver simulates CQE's for ULPs that rely on
completion of all their posted work-request.
For the GSI traffic, the mlx5 has its own mechanism that sends the
completions via software CQE's directly to the relevant CQ.
This should be kept in fatal error too, so the driver should simulate
such CQE's with the specified error state in order to complete GSI QP
work requests.
Without the fix the next deadlock might appears:
schedule_timeout+0x274/0x350
wait_for_common+0xec/0x240
mcast_remove_one+0xd0/0x120 [ib_core]
ib_unregister_device+0x12c/0x230 [ib_core]
mlx5_ib_remove+0xc4/0x270 [mlx5_ib]
mlx5_detach_device+0x184/0x1a0 [mlx5_core]
mlx5_unload_one+0x308/0x340 [mlx5_core]
mlx5_pci_err_detected+0x74/0xe0 [mlx5_core]
Cc: <stable@vger.kernel.org> # 4.7
Fixes: 89ea94a7b6 ("IB/mlx5: Reset flow support for IB kernel ULPs")
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d8f9cc328c upstream.
To allow rereg_user_mr to modify the MR from read-only to writable without
using get_user_pages again, we needed to define the initial MR as writable.
However, this was originally done unconditionally, without taking into
account the writability of the underlying virtual memory.
As a result, any attempt to register a read-only MR over read-only
virtual memory failed.
To fix this, do not add the writable flag bit when the user virtual memory
is not writable (e.g. const memory).
However, when the underlying memory is NOT writable (and we therefore
do not define the initial MR as writable), the IB core adds a
"force writable" flag to its user-pages request. If this succeeds,
the reg_user_mr caller gets a writable copy of the original pages.
If the user-space caller then does a rereg_user_mr operation to enable
writability, this will succeed. This should not be allowed, since
the original virtual memory was not writable.
Cc: <stable@vger.kernel.org>
Fixes: 9376932d0c ("IB/mlx4_ib: Add support for user MR re-registration")
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 52e1cf2d19 upstream.
Commit:
79832f0b5f ("efi/libstub/tpm: Initialize pointer variables to zero for mixed mode")
fixes a problem with the tpm code on mixed mode (64-bit kernel on 32-bit UEFI),
where 64-bit pointer variables are not fully initialized by the 32-bit EFI code.
A similar problem applies to the efi_physical_addr_t variables which
are written by the ->get_event_log() EFI call. Even though efi_physical_addr_t
is 64-bit everywhere, it seems that some 32-bit UEFI implementations only
fill in the lower 32 bits when passed a pointer to an efi_physical_addr_t
to fill.
This commit initializes these to 0 to, to ensure the upper 32 bits are
0 in mixed mode. This fixes recent kernels sometimes hanging during
early boot on mixed mode UEFI systems.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: <stable@vger.kernel.org> # v4.16+
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20180622064222.11633-2-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ab2011ea3 upstream.
There is a race condition in tpm_common_write function allowing
two threads on the same /dev/tpm<N>, or two different applications
on the same /dev/tpmrm<N> to overwrite each other commands/responses.
Fixed this by taking the priv->buffer_mutex early in the function.
Also converted the priv->data_pending from atomic to a regular size_t
type. There is no need for it to be atomic since it is only touched
under the protection of the priv->buffer_mutex.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3b9cf7905f upstream.
For strings, account for trailing \0 in property length field:
This is consistent with how dtc builds string properties.
Function __of_prop_dup() would misbehave on such properties as it duplicates
properties based on the property length field creating new string values
without trailing \0s.
Signed-off-by: Stefan M Schaeckeler <sschaeck@cisco.com>
Reviewed-by: Frank Rowand <frank.rowand@sony.com>
Tested-by: Frank Rowand <frank.rowand@sony.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 482137bf2a upstream.
The smatch static checker marks the data in offset as untrusted,
leading it to warn:
drivers/of/resolver.c:125 update_usages_of_a_phandle_reference()
error: buffer underflow 'prop->value' 's32min-s32max'
Add check to verify that offset is within the property data.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 48e21ded04 upstream.
Vendor firmware/uboot has different reserved regions depending on
firmware version, but current codebase reserves the same regions on
GXL and GXBB, so move the additional reserved memory region to common
.dtsi.
Found when putting a recent vendor u-boot on meson-gxbb-p200.
Suggested-by: Neil Armstrong <narmstrong@baylibre.com>
Cc: stable@vger.kernel.org
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d5b4885b1d upstream.
There is a problem with the sd-uhs mode when doing a soft reboot.
Switching back from 1.8v to 3.3v messes with the card, which no longer
respond (timeout errors). According to the specification, we should
perform a card reset (power cycling the card) but this is something we
cannot control on this design.
Then the only solution to restore the communication with the card is an
"unplug-plug" which is not acceptable
Until we find a solution, if any, disable the sd-uhs modes on this design.
For the people using uhs at the moment, there will a performance drop as
a result.
Fixes: 3cde63ebc8 ("ARM64: dts: meson-gxl: libretech-cc: enable high speed modes")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Cc: stable@vger.kernel.org
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 71c8fc0c96 upstream.
When rewriting swapper using nG mappings, we must performance cache
maintenance around each page table access in order to avoid coherency
problems with the host's cacheable alias under KVM. To ensure correct
ordering of the maintenance with respect to Device memory accesses made
with the Stage-1 MMU disabled, DMBs need to be added between the
maintenance and the corresponding memory access.
This patch adds a missing DMB between writing a new page table entry and
performing a clean+invalidate on the same line.
Fixes: f992b4dfd5 ("arm64: kpti: Add ->enable callback to remap swapper using nG mappings")
Cc: <stable@vger.kernel.org> # 4.16.x-
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5b7dd647f upstream.
We inspect __kpti_forced early on as part of the cpufeature enable
callback which remaps the swapper page table using non-global entries.
Ensure that __kpti_forced has been updated to reflect the kpti=
command-line option before we start using it.
Fixes: ea1e3de85e ("arm64: entry: Add fake CPU feature for unmapping the kernel at EL0")
Cc: <stable@vger.kernel.org> # 4.16.x-
Reported-by: Wei Xu <xuwei5@hisilicon.com>
Tested-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Wei Xu <xuwei5@hisilicon.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0fe42512b2 upstream.
Commit 17c2895 ("arm64: Abstract syscallno manipulation") abstracts
out the pt_regs.syscallno value for a syscall cancelled by a tracer
as NO_SYSCALL, and provides helpers to set and check for this
condition. However, the way this was implemented has the
unintended side-effect of disabling part of the syscall restart
logic.
This comes about because the second in_syscall() check in
do_signal() re-evaluates the "in a syscall" condition based on the
updated pt_regs instead of the original pt_regs. forget_syscall()
is explicitly called prior to the second check in order to prevent
restart logic in the ret_to_user path being spuriously triggered,
which means that the second in_syscall() check always yields false.
This triggers a failure in
tools/testing/selftests/seccomp/seccomp_bpf.c, when using ptrace to
suppress a signal that interrups a nanosleep() syscall.
Misbehaviour of this type is only expected in the case where a
tracer suppresses a signal and the target process is either being
single-stepped or the interrupted syscall attempts to restart via
-ERESTARTBLOCK.
This patch restores the old behaviour by performing the
in_syscall() check only once at the start of the function.
Fixes: 17c2895860 ("arm64: Abstract syscallno manipulation")
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Reported-by: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: <stable@vger.kernel.org> # 4.14.x-
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 837bf7cc3b upstream.
enable_best_rng() is used in hwrng_unregister() to switch away from the
currently active RNG, if that is the one currently being removed.
However enable_best_rng() might fail, if the next RNG's init routine
fails. In that case enable_best_rng() will return an error code and
the currently active RNG will remain active.
After unregistering this might lead to crashes due to use-after-free.
Fix this by dropping the currently active RNG, if enable_best_rng()
failed. This will result in no RNG to be active, if the next-best
one failed to initialize.
This problem was introduced by 142a27f0a7
Fixes: 142a27f0a7 ("hwrng: core - Reset user selected rng by...")
Reported-by: Wirz <spam@lukas-wirz.de>
Tested-by: Wirz <spam@lukas-wirz.de>
Signed-off-by: Michael Büsch <m@bues.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3877ef7a1c upstream.
The NAND compatible "denali,denal-nand-dt" property has never been used and
is obsolete. Remove it.
Cc: stable@vger.kernel.org
Fixes: f549af06e9b6("ARM: dts: socfpga: Add NAND device tree for Arria10")
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4eda9b766b upstream.
The Denali NAND x-clock should be supplied by nand_x_clk, not by
nand_clk. Fix this, otherwise the Denali driver gets incorrect
clock frequency information and incorrectly configures the NAND
timing.
Cc: stable@vger.kernel.org
Signed-off-by: Marek Vasut <marex@denx.de>
Fixes: d837a80d19 ("ARM: dts: socfpga: add nand controller nodes")
Cc: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bceb1f25b8 upstream.
The voltage of the VCC-1V2 regulator on the ALL-H3-CC H3 ver. should be
1.2V, not the 3.3V currently defined in the device tree.
Fix the voltage in the device tree.
Fixes: 6ca358645d ("ARM: dts: sun8i: h3: Add dts file for Libre
Computer Board ALL-H3-CC H3 ver.")
Cc: <stable@vger.kernel.org> # 4.16.x
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e6e7b7c2c8 upstream.
The VDD-CPUX voltage of ALL-H3-CC H3 ver should be 1.2V, not the 3.3V
currently defined in the device tree.
Fix the voltage in the device tree.
Fixes: 6ca358645d ("ARM: dts: sun8i: h3: Add dts file for Libre Computer Board ALL-H3-CC H3 ver.")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Cc: <stable@vger.kernel.org> # 4.16.x
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 76ed0b803a upstream.
NUMREGBYTES (which is used as the size for gdb_regs[]) is incorrectly
based on DBG_MAX_REG_NUM instead of GDB_MAX_REGS. DBG_MAX_REG_NUM
is the number of total registers, while GDB_MAX_REGS is the number
of 'unsigned longs' it takes to serialize those registers. Since
FP registers require 3 'unsigned longs' each, DBG_MAX_REG_NUM is
smaller than GDB_MAX_REGS.
This causes GDB 8.0 give the following error on connect:
"Truncated register 19 in remote 'g' packet"
This also causes the register serialization/deserialization logic
to overflow gdb_regs[], overwriting whatever follows.
Fixes: 834b2964b7 ("kgdb,arm: fix register dump")
Cc: <stable@vger.kernel.org> # 2.6.37+
Signed-off-by: David Rivshin <drivshin@allworx.com>
Acked-by: Rabin Vincent <rabin@rab.in>
Tested-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b6c84ba22f upstream.
Currently we see a kernel-oops reported on Power-9 while attaching a
context to an AFU, with radix-mode and sysfs attr 'prefault_mode' set
to anything other than 'none'. The backtrace of the oops is of this
form:
Unable to handle kernel paging request for data at address 0x00000080
Faulting instruction address: 0xc00800000bcf3b20
cpu 0x1: Vector: 300 (Data Access) at [c00000037f003800]
pc: c00800000bcf3b20: cxl_load_segment+0x178/0x290 [cxl]
lr: c00800000bcf39f0: cxl_load_segment+0x48/0x290 [cxl]
sp: c00000037f003a80
msr: 9000000000009033
dar: 80
dsisr: 40000000
current = 0xc00000037f280000
paca = 0xc0000003ffffe600 softe: 3 irq_happened: 0x01
pid = 3529, comm = afp_no_int
<snip>
cxl_prefault+0xfc/0x248 [cxl]
process_element_entry_psl9+0xd8/0x1a0 [cxl]
cxl_attach_dedicated_process_psl9+0x44/0x130 [cxl]
native_attach_process+0xc0/0x130 [cxl]
afu_ioctl+0x3f4/0x5e0 [cxl]
do_vfs_ioctl+0xdc/0x890
ksys_ioctl+0x68/0xf0
sys_ioctl+0x40/0xa0
system_call+0x58/0x6c
The issue is caused as on Power-8 the AFU attr 'prefault_mode' was
used to improve initial storage fault performance by prefaulting
process segments. However on Power-9 with radix mode we don't have
Storage-Segments that we can prefault. Also prefaulting process Pages
will be too costly and fine-grained.
Hence, since the prefaulting mechanism doesn't makes sense of
radix-mode, this patch updates prefault_mode_store() to not allow any
other value apart from CXL_PREFAULT_NONE when radix mode is enabled.
Fixes: f24be42aab ("cxl: Add psl9 specific code")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Vaibhav Jain <vaibhav@linux.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Acked-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 749a0278c2 upstream.
In the device tree CPU features quirk code we want to set
CPU_FTR_POWER9_DD2_1 on all Power9s that aren't DD2.0 or earlier. But
we got the logic wrong and instead set it on all CPUs that aren't
Power9 DD2.0 or earlier, ie. including Power8.
Fix it by making sure we're on a Power9. This isn't a bug in practice
because the only code that checks the feature is Power9 only to begin
with. But we'll backport it anyway to avoid confusion.
Fixes: 9e9626ed3a ("powerpc/64s: Fix POWER9 DD2.2 and above in DT CPU features")
Cc: stable@vger.kernel.org # v4.17+
Reported-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 546eb0317c upstream.
This commit:
5fdf8e5ba5 ("libnvdimm: re-enable deep flush for pmem devices via fsync()")
intended to make sure that deep flush was always available even on
platforms which support a power-fail protected CPU cache. An unintended
side effect of this change was that we also lost the ability to skip
flushing CPU caches on those power-fail protected CPU cache.
Fix this by skipping the low level cache flushing in dax_flush() if we have
CPU caches which are power-fail protected. The user can still override this
behavior by manually setting the write_cache state of a namespace. See
libndctl's ndctl_namespace_write_cache_is_enabled(),
ndctl_namespace_enable_write_cache() and
ndctl_namespace_disable_write_cache() functions.
Cc: <stable@vger.kernel.org>
Fixes: 5fdf8e5ba5 ("libnvdimm: re-enable deep flush for pmem devices via fsync()")
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 722cde76d6 upstream.
Unregister fadump on kexec down path otherwise the fadump registration
in new kexec-ed kernel complains that fadump is already registered.
This makes new kernel to continue using fadump registered by previous
kernel which may lead to invalid vmcore generation. Hence this patch
fixes this issue by un-registering fadump in fadump_cleanup() which is
called during kexec path so that new kernel can register fadump with
new valid values.
Fixes: b500afff11 ("fadump: Invalidate registration and release reserved memory for general use.")
Cc: stable@vger.kernel.org # v3.4+
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ac9816dcba upstream.
Init all present cpus for deep states instead of "all possible" cpus.
Init fails if a possible cpu is guarded. Resulting in making only
non-deep states available for cpuidle/hotplug.
Stewart says, this means that for single threaded workloads, if you
guard out a CPU core you'll not get WoF (Workload Optimised
Frequency), which means that performance goes down when you wouldn't
expect it to.
Fixes: 77b54e9f21 ("powernv/powerpc: Add winkle support for offline cpus")
Cc: stable@vger.kernel.org # v3.19+
Signed-off-by: Akshay Adiga <akshay.adiga@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7574364906 upstream.
NX can set the 3rd bit in CR register for XER[SO] (Summary overflow)
which is not related to paste request. The current paste function
returns failure for a successful request when this bit is set. So mask
this bit and check the proper return status.
Fixes: 2392c8c8c0 ("powerpc/powernv/vas: Define copy/paste interfaces")
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 98fd72fe82 upstream.
When IODA2 creates a PE, it creates an IOMMU table with it_ops::free
set to pnv_ioda2_table_free() which calls pnv_pci_ioda2_table_free_pages().
Since iommu_tce_table_put() calls it_ops::free when the last reference
to the table is released, explicit call to pnv_pci_ioda2_table_free_pages()
is not needed so let's remove it.
This should fix double free in the case of PCI hotuplug as
pnv_pci_ioda2_table_free_pages() does not reset neither
iommu_table::it_base nor ::it_size.
This was not exposed by SRIOV as it uses different code path via
pnv_pcibios_sriov_disable().
IODA1 does not inialize it_ops::free so it does not have this issue.
Fixes: c5f7700bbd ("powerpc/powernv: Dynamically release PE")
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd6ef7eebf upstream.
Back when we first introduced the DAWR, in commit 4ae7ebe952
("powerpc: Change hardware breakpoint to allow longer ranges"), we
screwed up the constraint making it a 1024 byte boundary rather than a
512. This makes the check overly permissive. Fortunately GDB is the
only real user and it always did they right thing, so we never
noticed.
This fixes the constraint to 512 bytes.
Fixes: 4ae7ebe952 ("powerpc: Change hardware breakpoint to allow longer ranges")
Cc: stable@vger.kernel.org # v3.9+
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d2032678e5 upstream.
Currently memory is allocated for core-imc based on cpu_present_mask,
which has bit 'cpu' set iff cpu is populated. We use (cpu number / threads
per core) as the array index to access the memory.
Under some circumstances firmware marks a CPU as GUARDed CPU and boot the
system, until cleared of errors, these CPU's are unavailable for all
subsequent boots. GUARDed CPUs are possible but not present from linux
view, so it blows a hole when we assume the max length of our allocation
is driven by our max present cpus, where as one of the cpus might be online
and be beyond the max present cpus, due to the hole.
So (cpu number / threads per core) value bounds the array index and leads
to memory overflow.
Call trace observed during a guard test:
Faulting instruction address: 0xc000000000149f1c
cpu 0x69: Vector: 380 (Data Access Out of Range) at [c000003fea303420]
pc:c000000000149f1c: prefetch_freepointer+0x14/0x30
lr:c00000000014e0f8: __kmalloc+0x1a8/0x1ac
sp:c000003fea3036a0
msr:9000000000009033
dar:c9c54b2c91dbf6b7
current = 0xc000003fea2c0000
paca = 0xc00000000fddd880 softe: 3 irq_happened: 0x01
pid = 1, comm = swapper/104
Linux version 4.16.7-openpower1 (smc@smc-desktop) (gcc version 6.4.0
(Buildroot 2018.02.1-00006-ga8d1126)) #2 SMP Fri May 4 16:44:54 PDT 2018
enter ? for help
call trace:
__kmalloc+0x1a8/0x1ac
(unreliable)
init_imc_pmu+0x7f4/0xbf0
opal_imc_counters_probe+0x3fc/0x43c
platform_drv_probe+0x48/0x80
driver_probe_device+0x22c/0x308
__driver_attach+0xa0/0xd8
bus_for_each_dev+0x88/0xb4
driver_attach+0x2c/0x40
bus_add_driver+0x1e8/0x228
driver_register+0xd0/0x114
__platform_driver_register+0x50/0x64
opal_imc_driver_init+0x24/0x38
do_one_initcall+0x150/0x15c
kernel_init_freeable+0x250/0x254
kernel_init+0x1c/0x150
ret_from_kernel_thread+0x5c/0xc8
Allocating memory for core-imc based on cpu_possible_mask, which has
bit 'cpu' set iff cpu is populatable, will fix this issue.
Reported-by: Pridhiviraj Paidipeddi <ppaidipe@linux.vnet.ibm.com>
Signed-off-by: Anju T Sudhakar <anju@linux.vnet.ibm.com>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Tested-by: Pridhiviraj Paidipeddi <ppaidipe@linux.vnet.ibm.com>
Fixes: 39a846db1d ("powerpc/perf: Add core IMC PMU support")
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f7c06e26e upstream.
In commit e2a800beac ("powerpc/hw_brk: Fix off by one error when
validating DAWR region end") we fixed setting the DAWR end point to
its max value via PPC_PTRACE_SETHWDEBUG. Unfortunately we broke
PTRACE_SET_DEBUGREG when setting a 512 byte aligned breakpoint.
PTRACE_SET_DEBUGREG currently sets the length of the breakpoint to
zero (memset() in hw_breakpoint_init()). This worked with
arch_validate_hwbkpt_settings() before the above patch was applied but
is now broken if the breakpoint is 512byte aligned.
This sets the length of the breakpoint to 8 bytes when using
PTRACE_SET_DEBUGREG.
Fixes: e2a800beac ("powerpc/hw_brk: Fix off by one error when validating DAWR region end")
Cc: stable@vger.kernel.org # v3.11+
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eabdb8ca86 upstream.
Disassociate the exec_key from a VMA if the VMA permission is not
PROT_EXEC anymore. Otherwise the exec_only key continues to be
associated with the vma, causing unexpected behavior.
The problem was reported on x86 by Shakeel Butt, which is also
applicable on powerpc.
Fixes: 5586cf61e1 ("powerpc: introduce execute-only pkey")
Cc: stable@vger.kernel.org # v4.16+
Reported-by: Shakeel Butt <shakeelb@google.com>
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Reviewed-by: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 91d0697188 upstream.
Currently we do not have an isync, or any other context synchronizing
instruction prior to the slbie/slbmte in _switch() that updates the
SLB entry for the kernel stack.
However that is not correct as outlined in the ISA.
From Power ISA Version 3.0B, Book III, Chapter 11, page 1133:
"Changing the contents of ... the contents of SLB entries ... can
have the side effect of altering the context in which data
addresses and instruction addresses are interpreted, and in which
instructions are executed and data accesses are performed.
...
These side effects need not occur in program order, and therefore
may require explicit synchronization by software.
...
The synchronizing instruction before the context-altering
instruction ensures that all instructions up to and including that
synchronizing instruction are fetched and executed in the context
that existed before the alteration."
And page 1136:
"For data accesses, the context synchronizing instruction before the
slbie, slbieg, slbia, slbmte, tlbie, or tlbiel instruction ensures
that all preceding instructions that access data storage have
completed to a point at which they have reported all exceptions
they will cause."
We're not aware of any bugs caused by this, but it should be fixed
regardless.
Add the missing isync when updating kernel stack SLB entry.
Cc: stable@vger.kernel.org
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
[mpe: Flesh out change log with more ISA text & explanation]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df0e91d488 upstream.
Fuse has an "atomic_o_trunc" mode, where userspace filesystem uses the
O_TRUNC flag in the OPEN request to truncate the file atomically with the
open.
In this mode there's no need to send a SETATTR request to userspace after
the open, so fuse_do_setattr() checks this mode and returns. But this
misses the important step of truncating the pagecache.
Add the missing parts of truncation to the ATTR_OPEN branch.
Reported-by: Chad Austin <chadaustin@fb.com>
Fixes: 6ff958edbf ("fuse: add atomic open+truncate support")
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a301eb16d upstream.
If a connection gets aborted while congested, FUSE can leave
nr_wb_congested[] stuck until reboot causing wait_iff_congested() to
wait spuriously which can lead to severe performance degradation.
The leak is caused by gating congestion state clearing with
fc->connected test in request_end(). This was added way back in 2009
by 26c3679101 ("fuse: destroy bdi on umount"). While the commit
description doesn't explain why the test was added, it most likely was
to avoid dereferencing bdi after it got destroyed.
Since then, bdi lifetime rules have changed many times and now we're
always guaranteed to have access to the bdi while the superblock is
alive (fc->sb).
Drop fc->connected conditional to avoid leaking congestion states.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Joshua Miller <joshmiller@fb.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: stable@vger.kernel.org # v2.6.29+
Acked-by: Jan Kara <jack@suse.cz>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe50a7d039 upstream.
There was one place where the timeout value for an operation was
not being set, if a capabilities request was done from idle. Move
the timeout value setting to before where that change might be
requested.
IMHO the cause here is the invisible returns in the macros. Maybe
that's a job for later, though.
Reported-by: Nordmark Claes <Claes.Nordmark@tieto.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2026d35741 upstream.
The function __builtin_expect returns long type (see the gcc
documentation), and so do macros likely and unlikely. Unfortunatelly, when
CONFIG_PROFILE_ANNOTATED_BRANCHES is selected, the macros likely and
unlikely expand to __branch_check__ and __branch_check__ truncates the
long type to int. This unintended truncation may cause bugs in various
kernel code (we found a bug in dm-writecache because of it), so it's
better to fix __branch_check__ to return long.
Link: http://lkml.kernel.org/r/alpine.LRH.2.02.1805300818140.24812@file01.intranet.prod.int.rdu2.redhat.com
Cc: Ingo Molnar <mingo@redhat.com>
Cc: stable@vger.kernel.org
Fixes: 1f0d69a9fc ("tracing: profile likely and unlikely annotations")
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 756b56a9e8 upstream.
The trigger code is picky in how it can be disabled as there may be
dependencies between different events and synthetic events. Change the order
on how triggers are reset.
1) Reset triggers of all synthetic events first
2) Remove triggers with actions attached to them
3) Remove all other triggers
If this order isn't followed, then some triggers will not be reset, and an
error may happen because a trigger is busy.
Cc: stable@vger.kernel.org
Fixes: cfa0963dc4 ("kselftests/ftrace : Add event trigger testcases")
Reviewed-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d302ed3cc upstream.
According to "EP93xx User’s Guide", I2STXLinCtrlData and I2SRXLinCtrlData
registers actually have different format. The only currently used bit
(Left_Right_Justify) has different position. Fix this and simplify the
whole setup taking into account the fact that both registers have zero
default value.
The practical effect of the above is repaired SND_SOC_DAIFMT_RIGHT_J
support (currently unused).
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2d534113be upstream.
The bit responsible for LRCLK polarity is i2s_tlrs (0), not i2s_trel (2)
(refer to "EP93xx User's Guide").
Previously card drivers which specified SND_SOC_DAIFMT_NB_IF actually got
SND_SOC_DAIFMT_NB_NF, an adaptation is necessary to retain the old
behavior.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff2faf1289 upstream.
dapm_kcontrol_data is freed as part of dapm_kcontrol_free(), leaving the
paths pointer dangling in the list.
This leads to system crash when we try to unload and reload sound card.
I hit this bug during ADSP crash/reboot test case on Dragon board DB410c.
Without this patch, on SLAB Poisoning enabled build, kernel crashes with
"BUG kmalloc-128 (Tainted: G W ): Poison overwritten"
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e01827ed9 upstream.
Some low-speed and full-speed devices (for example, bluetooth)
do not have time to initialize. For them, ETIMEDOUT is a valid error.
We need to give them another try. Otherwise, they will
never be initialized correctly and in dmesg will be messages
"Bluetooth: hci0 command 0x1002 tx timeout" or similars.
Fixes: 264904ccc3 ("usb: retry reset if a device times out")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Maxim Moseychuk <franchesko.salias.hudro.pedros@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef5332c10d upstream.
This reverts commit e060d376cc ("mmc: renesas_sdhi: fix WP detection")
and adds some code to really fix the regressions.
It was missed so far that Renesas R-Car instantiations of SDHI chose to
disable internal WP and used the existence of "wp-gpios" to en/disable
WP at all.
With the first refactoring by Yamada-san with commit 2ad1db059b ("mmc:
renesas_sdhi: use MMC_CAP2_NO_WRITE_PROTECT instead of TMIO own flag"),
WP was always disabled even when GPIOs were present. With Wolfram's
first fix which gets now reverted, GPIOs were honored. But when not
available, the fallback was to internal WP and not to disabled WP. This
caused wrong WP status on uSD card slots.
Restore the old behaviour now. By default, WP is disabled. When a GPIO
is found, the GPIO re-enables WP. We will think about possible better
ways to handle this in the future.
Tested on a previously regressing Renesas Lager board (H2) and a still
working Renesas Salvator-X board (M3-W).
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: stable@vger.kernel.org # v4.17+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c5c2a97b3a upstream.
This commit fixes a rare but possible case when the clk rate is updated
without update of the regulator voltage.
At boot up, CPUfreq checks if the system is running at the right freq. This
is a sanity check in case a bootloader set clk rate that is outside of freq
table present with cpufreq core. In such cases system can be unstable so
better to change it to a freq that is preset in freq-table.
The CPUfreq takes next freq that is >= policy->cur and this is our
target_freq that needs to be set now.
dev_pm_opp_set_rate(dev, target_freq) checks the target_freq and the
old_freq (a current rate). If these are equal it returns early. If not,
it searches for OPP (old_opp) that fits best to old_freq (not listed in
the table) and updates old_freq (!).
Here, we can end up with old_freq = old_opp.rate = target_freq, which
is not handled in _generic_set_opp_regulator(). It's supposed to update
voltage only when freq > old_freq || freq > old_freq.
if (freq > old_freq) {
ret = _set_opp_voltage(dev, reg, new_supply);
[...]
if (freq < old_freq) {
ret = _set_opp_voltage(dev, reg, new_supply);
if (ret)
It results in, no voltage update while clk rate is updated.
Example:
freq-table = {
1000MHz 1.15V
666MHZ 1.10V
333MHz 1.05V
}
boot-up-freq = 800MHz # not listed in freq-table
freq = target_freq = 1GHz
old_freq = 800Mhz
old_opp = _find_freq_ceil(opp_table, &old_freq); #(old_freq is modified!)
old_freq = 1GHz
Fixes: 6a0712f6f1 ("PM / OPP: Add dev_pm_opp_set_rate()")
Cc: 4.6+ <stable@vger.kernel.org> # v4.6+
Signed-off-by: Waldemar Rymarkiewicz <waldemar.rymarkiewicz@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 47e5abfb54 upstream.
If a device link is added via device_link_add() by the driver of the
link's consumer device, the supplier's runtime PM usage counter is
going to be dropped by the pm_runtime_put_suppliers() call in
driver_probe_device(). However, in that case it is not incremented
unless the supplier driver is already present and the link is not
stateless. That leads to a runtime PM usage counter imbalance for
the supplier device in a few cases.
To prevent that from happening, bump up the supplier runtime
PM usage counter in device_link_add() for all links with the
DL_FLAG_PM_RUNTIME flag set that are added at the consumer probe
time. Use pm_runtime_get_noresume() for that as the callers of
device_link_add() who want the supplier to be resumed by it are
expected to pass DL_FLAG_RPM_ACTIVE in flags to it anyway, but
additionally resume the supplier if the link is added during
consumer driver probe to retain the existing behavior for the
callers depending on it.
Fixes: 21d5c57b37 (PM / runtime: Use device links)
Reported-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: 4.10+ <stable@vger.kernel.org> # 4.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 656088aa9b upstream.
The state_saved flag should not be cleared in pci_pm_suspend() if the
given device is going to remain suspended, or the device's config
space will not be restored properly during the subsequent resume.
Namely, if the device is going to stay in suspend, both the late
and noirq callbacks return early for it, so if its state_saved flag
is cleared in pci_pm_suspend(), it will remain unset throughout the
remaining part of suspend and resume and pci_restore_state() called
for the device going forward will return without doing anything.
For this reason, change pci_pm_suspend() to only clear state_saved
if the given device is not going to remain suspended. [This is
analogous to what commit ae860a19f3 (PCI / PM: Do not clear
state_saved in pci_pm_freeze() when smart suspend is set) did for
hibernation.]
Fixes: c4b65157ae (PCI / PM: Take SMART_SUSPEND driver flag into account)
Cc: 4.15+ <stable@vger.kernel.org> # 4.15+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 72038df3c5 upstream.
In case the PM domain fails to be powered on in genpd_dev_pm_attach(), it
returns -EPROBE_DEFER, but keeping the device attached to its PM domain.
This leads to problems when the next attempt to attach is re-tried. More
precisely, in that situation an -EEXIST error code is returned, because the
device already has its PM domain pointer assigned, from the first attempt.
Now, because of the sloppy error handling by the existing callers of
dev_pm_domain_attach(), probing is allowed to continue when -EEXIST is
returned. However, in such case there are no guarantees that the PM domain
is powered on by genpd, which may lead to hangs when buses/drivers tried to
access their devices.
Let's fix this behaviour, simply by detaching the device when powering on
fails in genpd_dev_pm_attach().
Cc: v4.11+ <stable@vger.kernel.org> # v4.11+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8afb1d2c12 upstream.
Commit 40f70c03e3 ("serial: sh-sci: add locking to console write
function to avoid SMP lockup") copied the strategy to avoid locking
problems in conjuncture with the console from the UART8250
driver. Instead using directly spin_{try}lock_irqsave(),
local_irq_save() followed by spin_{try}lock() was used. While this is
correct on mainline, for -rt it is a problem. spin_{try}lock() will
check if it is running in a valid context. Since the local_irq_save()
has already been executed, the context has changed and
spin_{try}lock() will complain. The reason why spin_{try}lock()
complains is that on -rt the spin locks are turned into mutexes and
therefore can sleep. Sleeping with interrupts disabled is not valid.
BUG: sleeping function called from invalid context at /home/wagi/work/rt/v4.4-cip-rt/kernel/locking/rtmutex.c:995
in_atomic(): 0, irqs_disabled(): 128, pid: 778, name: irq/76-eth0
CPU: 0 PID: 778 Comm: irq/76-eth0 Not tainted 4.4.126-test-cip22-rt14-00403-gcd03665c8318 #12
Hardware name: Generic RZ/G1 (Flattened Device Tree)
Backtrace:
[<c00140a0>] (dump_backtrace) from [<c001424c>] (show_stack+0x18/0x1c)
r7:c06b01f0 r6:60010193 r5:00000000 r4:c06b01f0
[<c0014234>] (show_stack) from [<c01d3c94>] (dump_stack+0x78/0x94)
[<c01d3c1c>] (dump_stack) from [<c004c134>] (___might_sleep+0x134/0x194)
r7:60010113 r6:c06d3559 r5:00000000 r4:ffffe000
[<c004c000>] (___might_sleep) from [<c04ded60>] (rt_spin_lock+0x20/0x74)
r5:c06f4d60 r4:c06f4d60
[<c04ded40>] (rt_spin_lock) from [<c02577e4>] (serial_console_write+0x100/0x118)
r5:c06f4d60 r4:c06f4d60
[<c02576e4>] (serial_console_write) from [<c0061060>] (call_console_drivers.constprop.15+0x10c/0x124)
r10:c06d2894 r9:c04e18b0 r8:00000028 r7:00000000 r6:c06d3559 r5:c06d2798
r4:c06b9914 r3:c02576e4
[<c0060f54>] (call_console_drivers.constprop.15) from [<c0062984>] (console_unlock+0x32c/0x430)
r10:c06d30d8 r9:00000028 r8:c06dd518 r7:00000005 r6:00000000 r5:c06d2798
r4:c06d2798 r3:00000028
[<c0062658>] (console_unlock) from [<c0062e1c>] (vprintk_emit+0x394/0x4f0)
r10:c06d2798 r9:c06d30ee r8:00000006 r7:00000005 r6:c06a78fc r5:00000027
r4:00000003
[<c0062a88>] (vprintk_emit) from [<c0062fa0>] (vprintk+0x28/0x30)
r10:c060bd46 r9:00001000 r8:c06b9a90 r7:c06b9a90 r6:c06b994c r5:c06b9a3c
r4:c0062fa8
[<c0062f78>] (vprintk) from [<c0062fb8>] (vprintk_default+0x10/0x14)
[<c0062fa8>] (vprintk_default) from [<c009cd30>] (printk+0x78/0x84)
[<c009ccbc>] (printk) from [<c025afdc>] (credit_entropy_bits+0x17c/0x2cc)
r3:00000001 r2:decade60 r1:c061a5ee r0:c061a523
r4:00000006
[<c025ae60>] (credit_entropy_bits) from [<c025bf74>] (add_interrupt_randomness+0x160/0x178)
r10:466e7196 r9:1f536000 r8:fffeef74 r7:00000000 r6:c06b9a60 r5:c06b9a3c
r4:dfbcf680
[<c025be14>] (add_interrupt_randomness) from [<c006536c>] (irq_thread+0x1e8/0x248)
r10:c006537c r9:c06cdf21 r8:c0064fcc r7:df791c24 r6:df791c00 r5:ffffe000
r4:df525180
[<c0065184>] (irq_thread) from [<c003fba4>] (kthread+0x108/0x11c)
r10:00000000 r9:00000000 r8:c0065184 r7:df791c00 r6:00000000 r5:df791d00
r4:decac000
[<c003fa9c>] (kthread) from [<c00101b8>] (ret_from_fork+0x14/0x3c)
r8:00000000 r7:00000000 r6:00000000 r5:c003fa9c r4:df791d00
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Daniel Wagner <daniel.wagner@siemens.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c7d6a82d90 upstream.
On many older systems using SW sequencer the PREOP_OPTYPE register
contains two preopcodes as following:
PREOP_OPTYPE=0xf2785006
The last two bytes are the opcodes decoded to:
0x50 - Write enable for volatile status register
0x06 - Write enable
The former is used to modify volatile bits in the status register. For
non-volatile bits the latter is needed. Preopcodes are used in SW
sequencer to send one command "atomically" without anything else
interfering the transfer. The sequence that gets executed is:
- Send preopcode (write enable) from PREOP_OPTYPE register
- Send the actual SPI command
- Poll busy bit in the status register (0x05, RDSR)
Commit 8c473dd61b ("spi-nor: intel-spi: Don't assume OPMENU0/1 to be
programmed by BIOS") enabled atomic sequence handling but because both
preopcodes are programmed, the following happens:
if (preop >> 8)
val |= SSFSTS_CTL_SPOP;
Since on these systems preop >> 8 == 0x50 we end up picking volatile
write enable instead. Because of this the actual write command is pretty
much NOP unless there is a WREN latched in the chip already.
Furthermore we should not really just assume that WREN was issued in
previous call to intel_spi_write_reg() because that might not be the
case.
This updates driver to first check that the opcode is actually available
in PREOP_OPTYPE register and if not return error back to the spi-nor
core (if the controller is not locked we program it now). In addition we
save the opcode to ispi->atomic_preopcode field which is checked in next
call to intel_spi_sw_cycle() to actually enable atomic sequence using
the requested preopcode.
Fixes: 8c473dd61b ("spi-nor: intel-spi: Don't assume OPMENU0/1 to be programmed by BIOS")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b410b12266 upstream.
Older models of Chromebooks did not describe the LPC EC in their ACPI
tables; starting with Strago-based devices Google is using GOOG0004 device
to describe EC LPC.
DMI-based match is fragile and does not work reliably, especially when
using custom firmware. It is also not needed when we can locate the right
ACPI device, so let's stop bailing out when DMI does not match but the
right ACPI device is present.
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f90f9ef2d upstream.
If 020/030 support is enabled, get_io_area() leaves an IO_SIZE gap
between mappings which is added to the vm_struct representing the
mapping. __ioremap() uses the actual requested size (after alignment),
while __iounmap() is passed the size from the vm_struct.
On 020/030, early termination descriptors are used to set up mappings of
extent 'size', which are validated on unmapping. The unmapped gap of
size IO_SIZE defeats the sanity check of the pmd tables, causing
__iounmap() to loop forever on 030.
On 040/060, unmapping of page table entries does not check for a valid
mapping, so the umapping loop always completes there.
Adjust size to be unmapped by the gap that had been added in the
vm_struct prior.
This fixes the hang in atari_platform_init() reported a long time ago,
and a similar one reported by Finn recently (addressed by removing
ioremap() use from the SWIM driver.
Tested on my Falcon in 030 mode - untested but should work the same on
040/060 (the extra page tables cleared there would never have been set
up anyway).
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
[geert: Minor commit description improvements]
[geert: This was fixed in 2.4.23, but not in 2.5.x]
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f74c8a647 upstream.
mce_no_way_out() does a quick check during #MC to see whether some of
the MCEs logged would require the kernel to panic immediately. And it
passes a struct mce where MCi_STATUS gets written.
However, after having saved a valid status value, the next iteration
of the loop which goes over the MCA banks on the CPU, overwrites the
valid status value because we're using struct mce as storage instead of
a temporary variable.
Which leads to MCE records with an empty status value:
mce: [Hardware Error]: CPU 0: Machine Check Exception: 6 Bank 0: 0000000000000000
mce: [Hardware Error]: RIP 10:<ffffffffbd42fbd7> {trigger_mce+0x7/0x10}
In order to prevent the loss of the status register value, return
immediately when severity is a panic one so that we can panic
immediately with the first fatal MCE logged. This is also the intention
of this function and not to noodle over the banks while a fatal MCE is
already logged.
Tony: read the rest of the MCA bank to populate the struct mce fully.
Suggested-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20180622095428.626-8-bp@alien8.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40c36e2741 upstream.
Some injection testing resulted in the following console log:
mce: [Hardware Error]: CPU 22: Machine Check Exception: f Bank 1: bd80000000100134
mce: [Hardware Error]: RIP 10:<ffffffffc05292dd> {pmem_do_bvec+0x11d/0x330 [nd_pmem]}
mce: [Hardware Error]: TSC c51a63035d52 ADDR 3234bc4000 MISC 88
mce: [Hardware Error]: PROCESSOR 0:50654 TIME 1526502199 SOCKET 0 APIC 38 microcode 2000043
mce: [Hardware Error]: Run the above through 'mcelog --ascii'
Kernel panic - not syncing: Machine check from unknown source
This confused everybody because the first line quite clearly shows
that we found a logged error in "Bank 1", while the last line says
"unknown source".
The problem is that the Linux code doesn't do the right thing
for a local machine check that results in a fatal error.
It turns out that we know very early in the handler whether the
machine check is fatal. The call to mce_no_way_out() has checked
all the banks for the CPU that took the local machine check. If
it says we must crash, we can do so right away with the right
messages.
We do scan all the banks again. This means that we might initially
not see a problem, but during the second scan find something fatal.
If this happens we print a slightly different message (so I can
see if it actually every happens).
[ bp: Remove unneeded severity assignment. ]
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: stable@vger.kernel.org # 4.2
Link: http://lkml.kernel.org/r/52e049a497e86fd0b71c529651def8871c804df0.1527283897.git.tony.luck@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c7d606f560 upstream.
Since we added support to add recovery from some errors inside the kernel in:
commit b2f9d678e2 ("x86/mce: Check for faults tagged in EXTABLE_CLASS_FAULT exception table entries")
we have done a less than stellar job at reporting the cause of recoverable
machine checks that occur in other parts of the kernel. The user just gets
the unhelpful message:
mce: [Hardware Error]: Machine check: Action required: unknown MCACOD
doubly unhelpful when they check the manual for the reported IA32_MSR_STATUS.MCACOD
and see that it is listed as one of the standard recoverable values.
Add an extra rule to the MCE severity table to catch this case and report it
as:
mce: [Hardware Error]: Machine check: Data load in unrecoverable area of kernel
Fixes: b2f9d678e2 ("x86/mce: Check for faults tagged in EXTABLE_CLASS_FAULT exception table entries")
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: stable@vger.kernel.org # 4.6+
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/4cc7c465150a9a48b8b9f45d0b840278e77eb9b5.1527283897.git.tony.luck@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eab6870fee upstream.
Mark Rutland noticed that GCC optimization passes have the potential to elide
necessary invocations of the array_index_mask_nospec() instruction sequence,
so mark the asm() volatile.
Mark explains:
"The volatile will inhibit *some* cases where the compiler could lift the
array_index_nospec() call out of a branch, e.g. where there are multiple
invocations of array_index_nospec() with the same arguments:
if (idx < foo) {
idx1 = array_idx_nospec(idx, foo)
do_something(idx1);
}
< some other code >
if (idx < foo) {
idx2 = array_idx_nospec(idx, foo);
do_something_else(idx2);
}
... since the compiler can determine that the two invocations yield the same
result, and reuse the first result (likely the same register as idx was in
originally) for the second branch, effectively re-writing the above as:
if (idx < foo) {
idx = array_idx_nospec(idx, foo);
do_something(idx);
}
< some other code >
if (idx < foo) {
do_something_else(idx);
}
... if we don't take the first branch, then speculatively take the second, we
lose the nospec protection.
There's more info on volatile asm in the GCC docs:
https://gcc.gnu.org/onlinedocs/gcc/Extended-Asm.html#Volatile
"
Reported-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: <stable@vger.kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Fixes: babdde2698 ("x86: Implement array_index_mask_nospec")
Link: https://lkml.kernel.org/lkml/152838798950.14521.4893346294059739135.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7810e6781e upstream.
In __alloc_pages_slowpath() we reset zonelist and preferred_zoneref for
allocations that can ignore memory policies. The zonelist is obtained
from current CPU's node. This is a problem for __GFP_THISNODE
allocations that want to allocate on a different node, e.g. because the
allocating thread has been migrated to a different CPU.
This has been observed to break SLAB in our 4.4-based kernel, because
there it relies on __GFP_THISNODE working as intended. If a slab page
is put on wrong node's list, then further list manipulations may corrupt
the list because page_to_nid() is used to determine which node's
list_lock should be locked and thus we may take a wrong lock and race.
Current SLAB implementation seems to be immune by luck thanks to commit
511e3a0588 ("mm/slab: make cache_grow() handle the page allocated on
arbitrary node") but there may be others assuming that __GFP_THISNODE
works as promised.
We can fix it by simply removing the zonelist reset completely. There
is actually no reason to reset it, because memory policies and cpusets
don't affect the zonelist choice in the first place. This was different
when commit 183f6371aa ("mm: ignore mempolicies when using
ALLOC_NO_WATERMARK") introduced the code, as mempolicies provided their
own restricted zonelists.
We might consider this for 4.17 although I don't know if there's
anything currently broken.
SLAB is currently not affected, but in kernels older than 4.7 that don't
yet have 511e3a0588 ("mm/slab: make cache_grow() handle the page
allocated on arbitrary node") it is. That's at least 4.4 LTS. Older
ones I'll have to check.
So stable backports should be more important, but will have to be
reviewed carefully, as the code went through many changes. BTW I think
that also the ac->preferred_zoneref reset is currently useless if we
don't also reset ac->nodemask from a mempolicy to NULL first (which we
probably should for the OOM victims etc?), but I would leave that for a
separate patch.
Link: http://lkml.kernel.org/r/20180525130853.13915-1-vbabka@suse.cz
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Fixes: 183f6371aa ("mm: ignore mempolicies when using ALLOC_NO_WATERMARK")
Acked-by: Mel Gorman <mgorman@techsingularity.net>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5cc41e0995 upstream.
WHen registering a new binfmt_misc handler, it is possible to overflow
the offset to get a negative value, which might crash the system, or
possibly leak kernel data.
Here is a crash log when 2500000000 was used as an offset:
BUG: unable to handle kernel paging request at ffff989cfd6edca0
IP: load_misc_binary+0x22b/0x470 [binfmt_misc]
PGD 1ef3e067 P4D 1ef3e067 PUD 0
Oops: 0000 [#1] SMP NOPTI
Modules linked in: binfmt_misc kvm_intel ppdev kvm irqbypass joydev input_leds serio_raw mac_hid parport_pc qemu_fw_cfg parpy
CPU: 0 PID: 2499 Comm: bash Not tainted 4.15.0-22-generic #24-Ubuntu
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.1-1 04/01/2014
RIP: 0010:load_misc_binary+0x22b/0x470 [binfmt_misc]
Call Trace:
search_binary_handler+0x97/0x1d0
do_execveat_common.isra.34+0x667/0x810
SyS_execve+0x31/0x40
do_syscall_64+0x73/0x130
entry_SYSCALL_64_after_hwframe+0x3d/0xa2
Use kstrtoint instead of simple_strtoul. It will work as the code
already set the delimiter byte to '\0' and we only do it when the field
is not empty.
Tested with offsets -1, 2500000000, UINT_MAX and INT_MAX. Also tested
with examples documented at Documentation/admin-guide/binfmt-misc.rst
and other registrations from packages on Ubuntu.
Link: http://lkml.kernel.org/r/20180529135648.14254-1-cascardo@canonical.com
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 670ae9caac upstream.
struct vhost_msg within struct vhost_msg_node is copied to userspace.
Unfortunately it turns out on 64 bit systems vhost_msg has padding after
type which gcc doesn't initialize, leaking 4 uninitialized bytes to
userspace.
This padding also unfortunately means 32 bit users of this interface are
broken on a 64 bit kernel which will need to be fixed separately.
Fixes: CVE-2018-1118
Cc: stable@vger.kernel.org
Reported-by: Kevin Easton <kevin@guarana.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reported-by: syzbot+87cfa083e727a224754b@syzkaller.appspotmail.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d471b6b22d upstream.
The HID descriptor for the 2nd-gen Intuos Pro large (PTH-860) contains
a typo which defines an incorrect logical maximum Y value. This causes
a small portion of the bottom of the tablet to become unusable (both
because the area is below the "bottom" of the tablet and because
'wacom_wac_event' ignores out-of-range values). It also results in a
skewed aspect ratio.
To fix this, we add a quirk to 'wacom_usage_mapping' which overwrites
the data with the correct value.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
CC: stable@vger.kernel.org # v4.10+
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ebeaa36754 upstream.
Current ISH driver only registers suspend/resume PM callbacks which don't
support hibernation (suspend to disk). Basically after hiberation, the ISH
can't resume properly and user may not see sensor events (for example: screen
rotation may not work).
User will not see a crash or panic or anything except the following message
in log:
hid-sensor-hub 001F:8086:22D8.0001: timeout waiting for response from ISHTP device
So this patch adds support for S4/hiberbation to ISH by using the
SIMPLE_DEV_PM_OPS() MACRO instead of struct dev_pm_ops directly. The suspend
and resume functions will now be used for both suspend to RAM and hibernation.
If power management is disabled, SIMPLE_DEV_PM_OPS will do nothing, the suspend
and resume related functions won't be used, so mark them as __maybe_unused to
clarify that this is the intended behavior, and remove #ifdefs for power
management.
Cc: stable@vger.kernel.org
Signed-off-by: Even Xu <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f6a4b4c9d0 upstream.
As long as a symlink inode remains in-core, the destination (and
therefore size) will not be re-fetched from the server, as it cannot
change. The original implementation of the attribute cache assumed that
setting the expiry time in the past was sufficient to cause a re-fetch
of all attributes on the next getattr. That does not work in this case.
The bug manifested itself as follows. When the command sequence
touch foo; ln -s foo bar; ls -l bar
is run, the output was
lrwxrwxrwx. 1 fedora fedora 4906 Apr 24 19:10 bar -> foo
However, after a re-mount, ls -l bar produces
lrwxrwxrwx. 1 fedora fedora 3 Apr 24 19:10 bar -> foo
After this commit, even before a re-mount, the output is
lrwxrwxrwx. 1 fedora fedora 3 Apr 24 19:10 bar -> foo
Reported-by: Becky Ligon <ligon@clemson.edu>
Signed-off-by: Martin Brandenburg <martin@omnibond.com>
Fixes: 71680c18c8 ("orangefs: Cache getattr results.")
Cc: stable@vger.kernel.org
Cc: hubcap@omnibond.com
Signed-off-by: Mike Marshall <hubcap@omnibond.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9039d98581 upstream.
The page loading code trusts the data provided in the firmware images
a bit too much and may cause a buffer overflow or copy unknown data if
the block sizes don't match what we expect.
To prevent potential problems, harden the code by checking if the
sizes we are copying are what we expect.
Cc: stable@vger.kernel.org
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d7832cd2a3 upstream.
Since commit cb84343fce ("media: lirc: do not call close() or open() on
unregistered devices") rc_open() will return -ENODEV if rcdev->registered
is false. Ensure this is set before we register the input device and the
lirc device, else we have a short window where the neither the lirc or
input device can be opened.
Fixes: cb84343fce ("media: lirc: do not call close() or open() on unregistered devices")
Cc: stable@vger.kernel.org # v4.16+
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0dc68cabdb upstream.
The addition of an extra operation to use the GET_INFO command
overwrites all existing flags from the uvc_ctrls table. This includes
setting all controls as supporting GET_MIN, GET_MAX, GET_RES, and
GET_DEF regardless of whether they do or not.
Move the initialisation of these control capabilities directly to the
uvc_ctrl_fill_xu_info() call where they were originally located in that
use case, and ensure that the new functionality in uvc_ctrl_get_flags()
will only set flags based on their reported capability from the GET_INFO
call.
Fixes: 859086ae36 ("media: uvcvideo: Apply flags from device to actual properties")
Cc: stable@vger.kernel.org
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Tested-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 12f47073a4 upstream.
The case that interrupt affinity setting fails with -EBUSY can be handled
in the kernel completely by using the already available generic pending
infrastructure.
If a irq_chip::set_affinity() fails with -EBUSY, handle it like the
interrupts for which irq_chip::set_affinity() can only be invoked from
interrupt context. Copy the new affinity mask to irq_desc::pending_mask and
set the affinity pending bit. The next raised interrupt for the affected
irq will check the pending bit and try to set the new affinity from the
handler. This avoids that -EBUSY is returned when an affinity change is
requested from user space and the previous change has not been cleaned
up. The new affinity will take effect when the next interrupt is raised
from the device.
Fixes: dccfe3147b ("x86/vector: Simplify vector move cleanup")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Song Liu <songliubraving@fb.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Song Liu <liu.song.a23@gmail.com>
Cc: Dmitry Safonov <0x7f454c46@gmail.com>
Cc: stable@vger.kernel.org
Cc: Mike Travis <mike.travis@hpe.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Tariq Toukan <tariqt@mellanox.com>
Link: https://lkml.kernel.org/r/20180604162224.819273597@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a33a5d2d16 upstream.
The generic pending interrupt mechanism moves interrupts from the interrupt
handler on the original target CPU to the new destination CPU. This is
required for x86 and ia64 due to the way the interrupt delivery and
acknowledge works if the interrupts are not remapped.
However that update can fail for various reasons. Some of them are valid
reasons to discard the pending update, but the case, when the previous move
has not been fully cleaned up is not a legit reason to fail.
Check the return value of irq_do_set_affinity() for -EBUSY, which indicates
a pending cleanup, and rearm the pending move in the irq dexcriptor so it's
tried again when the next interrupt arrives.
Fixes: 996c591227 ("x86/irq: Plug vector cleanup race")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Song Liu <songliubraving@fb.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Song Liu <liu.song.a23@gmail.com>
Cc: Dmitry Safonov <0x7f454c46@gmail.com>
Cc: stable@vger.kernel.org
Cc: Mike Travis <mike.travis@hpe.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Tariq Toukan <tariqt@mellanox.com>
Link: https://lkml.kernel.org/r/20180604162224.386544292@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c0255770cc upstream.
apic_ack_edge() is explicitely for handling interrupt affinity cleanup when
interrupt remapping is not available or disable.
Remapped interrupts and also some of the platform specific special
interrupts, e.g. UV, invoke ack_APIC_irq() directly.
To address the issue of failing an affinity update with -EBUSY the delayed
affinity mechanism can be reused, but ack_APIC_irq() does not handle
that. Adding this to ack_APIC_irq() is not possible, because that function
is also used for exceptions and directly handled interrupts like IPIs.
Create a new function, which just contains the conditional invocation of
irq_move_irq() and the final ack_APIC_irq().
Reuse the new function in apic_ack_edge().
Preparatory change for the real fix.
Fixes: dccfe3147b ("x86/vector: Simplify vector move cleanup")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Song Liu <songliubraving@fb.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Song Liu <liu.song.a23@gmail.com>
Cc: Dmitry Safonov <0x7f454c46@gmail.com>
Cc: stable@vger.kernel.org
Cc: Mike Travis <mike.travis@hpe.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Tariq Toukan <tariqt@mellanox.com>
Link: https://lkml.kernel.org/r/20180604162224.471925894@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 80ae7b1a91 upstream.
Several people observed the WARN_ON() in irq_matrix_free() which triggers
when the caller tries to free an vector which is not in the allocation
range. Song provided the trace information which allowed to decode the root
cause.
The rework of the vector allocation mechanism failed to preserve a sanity
check, which prevents setting a new target vector/CPU when the previous
affinity change has not fully completed.
As a result a half finished affinity change can be overwritten, which can
cause the leak of a irq descriptor pointer on the previous target CPU and
double enqueue of the hlist head into the cleanup lists of two or more
CPUs. After one CPU cleaned up its vector the next CPU will invoke the
cleanup handler with vector 0, which triggers the out of range warning in
the matrix allocator.
Prevent this by checking the apic_data of the interrupt whether the
move_in_progress flag is false and the hlist node is not hashed. Return
-EBUSY if not.
This prevents the damage and restores the behaviour before the vector
allocation rework, but due to other changes in that area it also widens the
chance that user space can observe -EBUSY. In theory this should be fine,
but actually not all user space tools handle -EBUSY correctly. Addressing
that is not part of this fix, but will be addressed in follow up patches.
Fixes: 69cde0004a ("x86/vector: Use matrix allocator for vector assignment")
Reported-by: Dmitry Safonov <0x7f454c46@gmail.com>
Reported-by: Tariq Toukan <tariqt@mellanox.com>
Reported-by: Song Liu <liu.song.a23@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Song Liu <songliubraving@fb.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: stable@vger.kernel.org
Cc: Mike Travis <mike.travis@hpe.com>
Cc: Borislav Petkov <bp@alien8.de>
Link: https://lkml.kernel.org/r/20180604162224.303870257@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 955bc61328 upstream.
According to the API, you may only call clk_get_rate() after actually
enabling it.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: a5fd9139f7 ("w1: add 1-wire master driver for i.MX27 / i.MX31")
Signed-off-by: Stefan Potyra <Stefan.Potyra@elektrobit.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc1d5e749a upstream.
AER handling expects a successful return from slot_reset means the
driver made the device functional again. The nvme driver had been using
an asynchronous reset to recover the device, so the device
may still be initializing after control is returned to the
AER handler. This creates problems for subsequent event handling,
causing the initializion to fail.
This patch fixes that by syncing the controller reset before returning
to the AER driver, and reporting the true state of the reset.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199657
Reported-by: Alex Gagniuc <mr.nuke.me@gmail.com>
Cc: Sinan Kaya <okaya@codeaurora.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Tested-by: Alex Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2cfce3a86b upstream.
Commit 184add2ca2 ("libata: Apply NOLPM quirk for SanDisk
SD7UB3Q*G1001 SSDs") disabled LPM for SanDisk SD7UB3Q*G1001 SSDs.
This has lead to several reports of users of that SSD where LPM
was working fine and who know have a significantly increased idle
power consumption on their laptops.
Likely there is another problem on the T450s from the original
reporter which gets exposed by the uncore reaching deeper sleep
states (higher PC-states) due to LPM being enabled. The problem as
reported, a hardfreeze about once a day, already did not sound like
it would be caused by LPM and the reports of the SSD working fine
confirm this. The original reporter is ok with dropping the quirk.
A X250 user has reported the same hard freeze problem and for him
the problem went away after unrelated updates, I suspect some GPU
driver stack changes fixed things.
TL;DR: The original reporters problem were triggered by LPM but not
an LPM issue, so drop the quirk for the SSD in question.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1583207
Cc: stable@vger.kernel.org
Cc: Richard W.M. Jones <rjones@redhat.com>
Cc: Lorenzo Dalrio <lorenzo.dalrio@gmail.com>
Reported-by: Lorenzo Dalrio <lorenzo.dalrio@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: "Richard W.M. Jones" <rjones@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7592019634 upstream.
According to current code implementation, detecting the long
idle period is done by checking if the interval between two
adjacent utilization update handlers is long enough. Although
this mechanism can detect if the idle period is long enough
(no utilization hooks invoked during idle period), it might
not cover a corner case: if the task has occupied the CPU
for too long which causes no context switches during that
period, then no utilization handler will be launched until this
high prio task is scheduled out. As a result, the idle_periods
field might be calculated incorrectly because it regards the
100% load as 0% and makes the conservative governor who uses
this field confusing.
Change the detection to compare the idle_time with sampling_rate
directly.
Reported-by: Artem S. Tashkinov <t.artem@mailcity.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e5d295b06d upstream.
Commit 05829d9431 (cpufreq: ti-cpufreq: kfree opp_data when
failure) has fixed a memory leak in the failure path, however
the patch returned a positive value on get_cpu_device() failure
instead of the previous negative value. Fix this incorrect error
return value properly.
Fixes: 05829d9431 (cpufreq: ti-cpufreq: kfree opp_data when failure)
Cc: 4.14+ <stable@vger.kernel.org> # v4.14+
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c7d1f119c4 upstream.
If the policy limits are updated via cpufreq_update_policy() and
subsequently via sysfs, the limits stored in user_policy may be
set incorrectly.
For example, if both min and max are set via sysfs to the maximum
available frequency, user_policy.min and user_policy.max will also
be the maximum. If a policy notifier triggered by
cpufreq_update_policy() lowers both the min and the max at this
point, that change is not reflected by the user_policy limits, so
if the max is updated again via sysfs to the same lower value,
then user_policy.max will be lower than user_policy.min which
shouldn't happen. In particular, if one of the policy CPUs is
then taken offline and back online, cpufreq_set_policy() will
fail for it due to a failing limits check.
To prevent that from happening, initialize the min and max fields
of the new_policy object to the ones stored in user_policy that
were previously set via sysfs.
Signed-off-by: Kevin Wangtao <kevin.wangtao@hisilicon.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
[ rjw: Subject & changelog ]
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f183464684 upstream.
From 0aa2e9b921d6db71150633ff290199554f0842a8 Mon Sep 17 00:00:00 2001
From: Tejun Heo <tj@kernel.org>
Date: Wed, 23 May 2018 10:29:00 -0700
cgwb_release() punts the actual release to cgwb_release_workfn() on
system_wq. Depending on the number of cgroups or block devices, there
can be a lot of cgwb_release_workfn() in flight at the same time.
We're periodically seeing close to 256 kworkers getting stuck with the
following stack trace and overtime the entire system gets stuck.
[<ffffffff810ee40c>] _synchronize_rcu_expedited.constprop.72+0x2fc/0x330
[<ffffffff810ee634>] synchronize_rcu_expedited+0x24/0x30
[<ffffffff811ccf23>] bdi_unregister+0x53/0x290
[<ffffffff811cd1e9>] release_bdi+0x89/0xc0
[<ffffffff811cd645>] wb_exit+0x85/0xa0
[<ffffffff811cdc84>] cgwb_release_workfn+0x54/0xb0
[<ffffffff810a68d0>] process_one_work+0x150/0x410
[<ffffffff810a71fd>] worker_thread+0x6d/0x520
[<ffffffff810ad3dc>] kthread+0x12c/0x160
[<ffffffff81969019>] ret_from_fork+0x29/0x40
[<ffffffffffffffff>] 0xffffffffffffffff
The events leading to the lockup are...
1. A lot of cgwb_release_workfn() is queued at the same time and all
system_wq kworkers are assigned to execute them.
2. They all end up calling synchronize_rcu_expedited(). One of them
wins and tries to perform the expedited synchronization.
3. However, that invovles queueing rcu_exp_work to system_wq and
waiting for it. Because #1 is holding all available kworkers on
system_wq, rcu_exp_work can't be executed. cgwb_release_workfn()
is waiting for synchronize_rcu_expedited() which in turn is waiting
for cgwb_release_workfn() to free up some of the kworkers.
We shouldn't be scheduling hundreds of cgwb_release_workfn() at the
same time. There's nothing to be gained from that. This patch
updates cgwb release path to use a dedicated percpu workqueue with
@max_active of 1.
While this resolves the problem at hand, it might be a good idea to
isolate rcu_exp_work to its own workqueue too as it can be used from
various paths and is prone to this sort of indirect A-A deadlocks.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a347c7ad8e upstream.
It is not allowed to reinit q->tag_set_list list entry while RCU grace
period has not completed yet, otherwise the following soft lockup in
blk_mq_sched_restart() happens:
[ 1064.252652] watchdog: BUG: soft lockup - CPU#12 stuck for 23s! [fio:9270]
[ 1064.254445] task: ffff99b912e8b900 task.stack: ffffa6d54c758000
[ 1064.254613] RIP: 0010:blk_mq_sched_restart+0x96/0x150
[ 1064.256510] Call Trace:
[ 1064.256664] <IRQ>
[ 1064.256824] blk_mq_free_request+0xea/0x100
[ 1064.256987] msg_io_conf+0x59/0xd0 [ibnbd_client]
[ 1064.257175] complete_rdma_req+0xf2/0x230 [ibtrs_client]
[ 1064.257340] ? ibtrs_post_recv_empty+0x4d/0x70 [ibtrs_core]
[ 1064.257502] ibtrs_clt_rdma_done+0xd1/0x1e0 [ibtrs_client]
[ 1064.257669] ib_create_qp+0x321/0x380 [ib_core]
[ 1064.257841] ib_process_cq_direct+0xbd/0x120 [ib_core]
[ 1064.258007] irq_poll_softirq+0xb7/0xe0
[ 1064.258165] __do_softirq+0x106/0x2a2
[ 1064.258328] irq_exit+0x92/0xa0
[ 1064.258509] do_IRQ+0x4a/0xd0
[ 1064.258660] common_interrupt+0x7a/0x7a
[ 1064.258818] </IRQ>
Meanwhile another context frees other queue but with the same set of
shared tags:
[ 1288.201183] INFO: task bash:5910 blocked for more than 180 seconds.
[ 1288.201833] bash D 0 5910 5820 0x00000000
[ 1288.202016] Call Trace:
[ 1288.202315] schedule+0x32/0x80
[ 1288.202462] schedule_timeout+0x1e5/0x380
[ 1288.203838] wait_for_completion+0xb0/0x120
[ 1288.204137] __wait_rcu_gp+0x125/0x160
[ 1288.204287] synchronize_sched+0x6e/0x80
[ 1288.204770] blk_mq_free_queue+0x74/0xe0
[ 1288.204922] blk_cleanup_queue+0xc7/0x110
[ 1288.205073] ibnbd_clt_unmap_device+0x1bc/0x280 [ibnbd_client]
[ 1288.205389] ibnbd_clt_unmap_dev_store+0x169/0x1f0 [ibnbd_client]
[ 1288.205548] kernfs_fop_write+0x109/0x180
[ 1288.206328] vfs_write+0xb3/0x1a0
[ 1288.206476] SyS_write+0x52/0xc0
[ 1288.206624] do_syscall_64+0x68/0x1d0
[ 1288.206774] entry_SYSCALL_64_after_hwframe+0x3d/0xa2
What happened is the following:
1. There are several MQ queues with shared tags.
2. One queue is about to be freed and now task is in
blk_mq_del_queue_tag_set().
3. Other CPU is in blk_mq_sched_restart() and loops over all queues in
tag list in order to find hctx to restart.
Because linked list entry was modified in blk_mq_del_queue_tag_set()
without proper waiting for a grace period, blk_mq_sched_restart()
never ends, spining in list_for_each_entry_rcu_rr(), thus soft lockup.
Fix is simple: reinit list entry after an RCU grace period elapsed.
Fixes: Fixes: 705cda97ee ("blk-mq: Make it safe to use RCU to iterate over blk_mq_tag_set.tag_list")
Cc: stable@vger.kernel.org
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: linux-block@vger.kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Roman Pen <roman.penyaev@profitbricks.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9e2b19675d upstream.
When we stopped relying on the bdev everywhere I broke updating the
block device size on the fly, which ceph relies on. We can't just do
set_capacity, we also have to do bd_set_size so things like parted will
notice the device size change.
Fixes: 29eaadc ("nbd: stop using the bdev everywhere")
cc: stable@vger.kernel.org
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c3f7c93976 upstream.
I messed up changing the size of an NBD device while it was connected by
not actually updating the device or doing the uevent. Fix this by
updating everything if we're connected and we change the size.
cc: stable@vger.kernel.org
Fixes: 639812a ("nbd: don't set the device size until we're connected")
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8364da4751 upstream.
This fixes a use after free bug, we shouldn't be doing disk->queue right
after we do del_gendisk(disk). Save the queue and do the cleanup after
the del_gendisk.
Fixes: c6a4759ea0 ("nbd: add device refcounting")
cc: stable@vger.kernel.org
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b2adf22fdf upstream.
The server detects reconnect by the (non-zero) value in PreviousSessionId
of SMB2/SMB3 SessionSetup request, but this behavior regressed due
to commit 166cea4dc3
("SMB2: Separate RawNTLMSSP authentication from SMB2_sess_setup")
CC: Stable <stable@vger.kernel.org>
CC: Sachin Prabhu <sprabhu@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 985c78d3ff upstream.
Each of the strings that we want to put into the buf[MAX_FLAG_OPT_SIZE]
in flags_read() is two characters long. But the sprintf() adds
a trailing newline and will add a terminating NUL byte. So
MAX_FLAG_OPT_SIZE needs to be 4.
sprintf() calls vsnprintf() and *that* does return:
" * The return value is the number of characters which would
* be generated for the given input, excluding the trailing
* '\0', as per ISO C99."
Note the "excluding".
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20180427163707.ktaiysvbk3yhk4wm@agluck-desk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a3aa60d511 upstream.
When 'kzalloc()' fails in 'snd_hda_attach_pcm_stream()', a new pcm instance is
created without setting its operators via 'snd_pcm_set_ops()'. Following
operations on the new pcm instance can trigger kernel null pointer dereferences
and cause kernel oops.
This bug was found with my work on building a gray-box fault-injection tool for
linux-kernel-module binaries. A kernel null pointer dereference was confirmed
from line 'substream->ops->open()' in function 'snd_pcm_open_substream()' in
file 'sound/core/pcm_native.c'.
This patch fixes the bug by calling 'snd_device_free()' in the error handling
path of 'kzalloc()', which removes the new pcm instance from the snd card before
returns with an error code.
Signed-off-by: Bo Chen <chenbo@pdx.edu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 986376b68d upstream.
We have several Lenovo AIOs like M810z, M820z and M920z, they have
the same design for mic-mute hotkey and led and they use the same
codec with the same pin configuration, so use the pin conf table to
apply fix to all of them.
Fixes: 29693efcea ("ALSA: hda - Fix micmute hotkey problem for a lenovo AIO machine")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ebf6b1e45 upstream.
The commit 33193dca67 ("ALSA: usb-audio: Add a quirk for Nura's
first gen headset") added a quirk for Nura headset with USB ID
0a12:1243, with a hope that it doesn't conflict with others.
Unfortunately, other devices (e.g. Philips Wecall) with the very same
ID got broken by this change, spewing an error like:
usb 2-1.8.2: 2:1: cannot set freq 48000 to ep 0x3
Until we find a proper solution, fix the regression at first by
disabling the added quirk entry.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=199905
Fixes: 33193dca67 ("ALSA: usb-audio: Add a quirk for Nura's first gen headset")
Reviewed-by: Martin Peres <martin.peres@free.fr>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ac0b4145d6 upstream.
[BUG]
Btrfs can create compressed extent without checksum (even though it
shouldn't), and if we then try to replace device containing such extent,
the result device will contain all the uncompressed data instead of the
compressed one.
Test case already submitted to fstests:
https://patchwork.kernel.org/patch/10442353/
[CAUSE]
When handling compressed extent without checksum, device replace will
goe into copy_nocow_pages() function.
In that function, btrfs will get all inodes referring to this data
extents and then use find_or_create_page() to get pages direct from that
inode.
The problem here is, pages directly from inode are always uncompressed.
And for compressed data extent, they mismatch with on-disk data.
Thus this leads to corrupted compressed data extent written to replace
device.
[FIX]
In this attempt, we could just remove the "optimization" branch, and let
unified scrub_pages() to handle it.
Although scrub_pages() won't bother reusing page cache, it will be a
little slower, but it does the correct csum checking and won't cause
such data corruption caused by "optimization".
Note about the fix: this is the minimal fix that can be backported to
older stable trees without conflicts. The whole callchain from
copy_nocow_pages() can be deleted, and will be in followup patches.
Fixes: ff023aac31 ("Btrfs: add code to scrub to copy read data to another disk")
CC: stable@vger.kernel.org # 4.4+
Reported-by: James Harvey <jamespharvey20@gmail.com>
Reviewed-by: James Harvey <jamespharvey20@gmail.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
[ remove code removal, add note why ]
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 090a127afa upstream.
In cow_file_range(), create_io_em() may fail, but its return value is
not recorded. Then return value may be 0 even it failed which is a
wrong behavior.
Let cow_file_range() return PTR_ERR(em) if create_io_em() failed.
Fixes: 6f9994dbab ("Btrfs: create a helper to create em for IO")
CC: stable@vger.kernel.org # 4.11+
Signed-off-by: Su Yue <suy.fnst@cn.fujitsu.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fd4e994bd1 upstream.
If we have invalid flags set, when we error out we must drop our writer
counter and free the buffer we allocated for the arguments. This bug is
trivially reproduced with the following program on 4.7+:
#include <fcntl.h>
#include <stdint.h>
#include <stdio.h>
#include <stdlib.h>
#include <unistd.h>
#include <sys/ioctl.h>
#include <sys/stat.h>
#include <sys/types.h>
#include <linux/btrfs.h>
#include <linux/btrfs_tree.h>
int main(int argc, char **argv)
{
struct btrfs_ioctl_vol_args_v2 vol_args = {
.flags = UINT64_MAX,
};
int ret;
int fd;
if (argc != 2) {
fprintf(stderr, "usage: %s PATH\n", argv[0]);
return EXIT_FAILURE;
}
fd = open(argv[1], O_WRONLY);
if (fd == -1) {
perror("open");
return EXIT_FAILURE;
}
ret = ioctl(fd, BTRFS_IOC_RM_DEV_V2, &vol_args);
if (ret == -1)
perror("ioctl");
close(fd);
return EXIT_SUCCESS;
}
When unmounting the filesystem, we'll hit the
WARN_ON(mnt_get_writers(mnt)) in cleanup_mnt() and also may prevent the
filesystem to be remounted read-only as the writer count will stay
lifted.
Fixes: 6b526ed70c ("btrfs: introduce device delete by devid")
CC: stable@vger.kernel.org # 4.9+
Signed-off-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Su Yue <suy.fnst@cn.fujitsu.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5c40d598f upstream.
In btrfs_clone_files(), we must check the NODATASUM flag while the
inodes are locked. Otherwise, it's possible that btrfs_ioctl_setflags()
will change the flags after we check and we can end up with a party
checksummed file.
The race window is only a few instructions in size, between the if and
the locks which is:
3834 if (S_ISDIR(src->i_mode) || S_ISDIR(inode->i_mode))
3835 return -EISDIR;
where the setflags must be run and toggle the NODATASUM flag (provided
the file size is 0). The clone will block on the inode lock, segflags
takes the inode lock, changes flags, releases log and clone continues.
Not impossible but still needs a lot of bad luck to hit unintentionally.
Fixes: 0e7b824c4e ("Btrfs: don't make a file partly checksummed through file clone")
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ update changelog ]
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 37becec95a upstream.
I got a report that after upgrading to 4.16, someone's filesystems
weren't mounting:
[ 23.845852] BTRFS info (device loop0): unrecognized mount option 'subvol='
Before 4.16, this mounted the default subvolume. It turns out that this
empty "subvol=" is actually an application bug, but it was causing the
application to fail, so it's an ABI break if you squint.
The generic parsing code we use for mount options (match_token())
doesn't match an empty string as "%s". Previously, setup_root_args()
removed the "subvol=" string, but the mount path was cleaned up to not
need that. Add a dummy Opt_subvol_empty to fix this.
The simple workaround is to use / or . for the value of 'subvol=' .
Fixes: 312c89fbca ("btrfs: cleanup btrfs_mount() using btrfs_mount_root()")
CC: stable@vger.kernel.org # 4.16+
Signed-off-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f2f76f751 upstream.
ext4_resize_fs() has an off-by-one bug when checking whether growing of
a filesystem will not overflow inode count. As a result it allows a
filesystem with 8192 inodes per group to grow to 64TB which overflows
inode count to 0 and makes filesystem unusable. Fix it.
Cc: stable@vger.kernel.org
Fixes: 3f8a6411fb
Reported-by: Jaco Kroon <jaco@uls.co.za>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a2b307c21 upstream.
Ext4 will always create ext4 extended attributes which do not have a
value (where e_value_size is zero) with e_value_offs set to zero. In
most places e_value_offs will not be used in a substantive way if
e_value_size is zero.
There was one exception to this, which is in ext4_xattr_set_entry(),
where if there is a maliciously crafted file system where there is an
extended attribute with e_value_offs is non-zero and e_value_size is
0, the attempt to remove this xattr will result in a negative value
getting passed to memmove, leading to the following sadness:
[ 41.225365] EXT4-fs (loop0): mounted filesystem with ordered data mode. Opts: (null)
[ 44.538641] BUG: unable to handle kernel paging request at ffff9ec9a3000000
[ 44.538733] IP: __memmove+0x81/0x1a0
[ 44.538755] PGD 1249bd067 P4D 1249bd067 PUD 1249c1067 PMD 80000001230000e1
[ 44.538793] Oops: 0003 [#1] SMP PTI
[ 44.539074] CPU: 0 PID: 1470 Comm: poc Not tainted 4.16.0-rc1+ #1
...
[ 44.539475] Call Trace:
[ 44.539832] ext4_xattr_set_entry+0x9e7/0xf80
...
[ 44.539972] ext4_xattr_block_set+0x212/0xea0
...
[ 44.540041] ext4_xattr_set_handle+0x514/0x610
[ 44.540065] ext4_xattr_set+0x7f/0x120
[ 44.540090] __vfs_removexattr+0x4d/0x60
[ 44.540112] vfs_removexattr+0x75/0xe0
[ 44.540132] removexattr+0x4d/0x80
...
[ 44.540279] path_removexattr+0x91/0xb0
[ 44.540300] SyS_removexattr+0xf/0x20
[ 44.540322] do_syscall_64+0x71/0x120
[ 44.540344] entry_SYSCALL_64_after_hwframe+0x21/0x86
https://bugzilla.kernel.org/show_bug.cgi?id=199347
This addresses CVE-2018-10840.
Reported-by: "Xu, Wen" <wen.xu@gatech.edu>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Cc: stable@kernel.org
Fixes: dec214d00e ("ext4: xattr inode deduplication")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eb9b5f01c3 upstream.
If ext4_find_inline_data_nolock() returns an error it needs to get
reflected up to ext4_iget(). In order to fix this,
ext4_iget_extra_inode() needs to return an error (and not return
void).
This is related to "ext4: do not allow external inodes for inline
data" (which fixes CVE-2018-11412) in that in the errors=continue
case, it would be useful to for userspace to receive an error
indicating that file system is corrupted.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 117166efb1 upstream.
The inline data feature was implemented before we added support for
external inodes for xattrs. It makes no sense to support that
combination, but the problem is that there are a number of extended
attribute checks that are skipped if e_value_inum is non-zero.
Unfortunately, the inline data code is completely e_value_inum
unaware, and attempts to interpret the xattr fields as if it were an
inline xattr --- at which point, Hilarty Ensues.
This addresses CVE-2018-11412.
https://bugzilla.kernel.org/show_bug.cgi?id=199803
Reported-by: Jann Horn <jannh@google.com>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Fixes: e50e5129f3 ("ext4: xattr-in-inode support")
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eee597ac93 upstream.
Currently in ext4_punch_hole we're going to skip the mtime update if
there are no actual blocks to release. However we've actually modified
the file by zeroing the partial block so the mtime should be updated.
Moreover the sync and datasync handling is skipped as well, which is
also wrong. Fix it.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reported-by: Joe Habermann <joe.habermann@quantum.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2ee3ee06a8 upstream.
When ext4_ind_map_blocks() computes a length of a hole, it doesn't count
with the fact that mapped offset may be somewhere in the middle of the
completely empty subtree. In such case it will return too large length
of the hole which then results in lseek(SEEK_DATA) to end up returning
an incorrect offset beyond the end of the hole.
Fix the problem by correctly taking offset within a subtree into account
when computing a length of a hole.
Fixes: facab4d971
CC: stable@vger.kernel.org
Reported-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5088814a6e upstream.
This change alters the parser so that the table load does not abort
upon an error.
Notable changes:
If there is an error while parsing an element of the termlist, we
will skip parsing the current termlist element and continue parsing
to the next opcode in the termlist.
If we get an error while parsing the conditional of If/Else/While or
the device name of Scope, we will skip the body of the statement all
together and pop the parser_state.
If we get an error while parsing the base offset and length of an
operation region declaration, we will remove the operation region
from the namespace.
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 52acf73b6e ]
Recently people reported the NIC stops working after
"ifdown eth0; ifup eth0". It turns out in this case the TX queues are not
enabled, after the refactoring of the common detach logic: when the NIC
has sub-channels, usually we enable all the TX queues after all
sub-channels are set up: see rndis_set_subchannel() ->
netif_device_attach(), but in the case of "ifdown eth0; ifup eth0" where
the number of channels doesn't change, we also must make sure the TX queues
are enabled. The patch fixes the regression.
Fixes: 7b2ee50c0c ("hv_netvsc: common detach logic")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fd3a886258 ]
Tun, tap, virtio, packet and uml vector all use struct virtio_net_hdr
to communicate packet metadata to userspace.
For skbuffs with vlan, the first two return the packet as it may have
existed on the wire, inserting the VLAN tag in the user buffer. Then
virtio_net_hdr.csum_start needs to be adjusted by VLAN_HLEN bytes.
Commit f09e2249c4 ("macvtap: restore vlan header on user read")
added this feature to macvtap. Commit 3ce9b20f19 ("macvtap: Fix
csum_start when VLAN tags are present") then fixed up csum_start.
Virtio, packet and uml do not insert the vlan header in the user
buffer.
When introducing virtio_net_hdr_from_skb to deduplicate filling in
the virtio_net_hdr, the variant from macvtap which adds VLAN_HLEN was
applied uniformly, breaking csum offset for packets with vlan on
virtio and packet.
Make insertion of VLAN_HLEN optional. Convert the callers to pass it
when needed.
Fixes: e858fae2b0 ("virtio_net: use common code for virtio_net_hdr and skb GSO conversion")
Fixes: 1276f24eee ("packet: use common code for virtio_net_hdr and skb GSO conversion")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6c206b2009 ]
After commit 6b229cf77d ("udp: add batching to udp_rmem_release()")
the sk_rmem_alloc field does not measure exactly anymore the
receive queue length, because we batch the rmem release. The issue
is really apparent only after commit 0d4a6608f6 ("udp: do rmem bulk
free even if the rx sk queue is empty"): the user space can easily
check for an empty socket with not-0 queue length reported by the 'ss'
tool or the procfs interface.
We need to use a custom UDP helper to report the correct queue length,
taking into account the forward allocation deficit.
Reported-by: trevor.francis@46labs.com
Fixes: 6b229cf77d ("UDP: add batching to udp_rmem_release()")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6d8c50dcb0 ]
fchownat() doesn't even hold refcnt of fd until it figures out
fd is really needed (otherwise is ignored) and releases it after
it resolves the path. This means sock_close() could race with
sockfs_setattr(), which leads to a NULL pointer dereference
since typically we set sock->sk to NULL in ->release().
As pointed out by Al, this is unique to sockfs. So we can fix this
in socket layer by acquiring inode_lock in sock_close() and
checking against NULL in sockfs_setattr().
sock_release() is called in many places, only the sock_close()
path matters here. And fortunately, this should not affect normal
sock_close() as it is only called when the last fd refcnt is gone.
It only affects sock_close() with a parallel sockfs_setattr() in
progress, which is not common.
Fixes: 86741ec254 ("net: core: Add a UID field to struct sock.")
Reported-by: shankarapailoor <shankarapailoor@gmail.com>
Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 06030dbaf3 ]
Current behavior in tls_sw_recvmsg() is to wait for incoming tls
messages and copy up to exactly len bytes of data that the user
provided. This is problematic in the sense that i) if no packet
is currently queued in strparser we keep waiting until one has been
processed and pushed into tls receive layer for tls_wait_data() to
wake up and push the decrypted bits to user space. Given after
tls decryption, we're back at streaming data, use sock_rcvlowat()
hint from tcp socket instead. Retain current behavior with MSG_WAITALL
flag and otherwise use the hint target for breaking the loop and
returning to application. This is done if currently no ctx->recv_pkt
is ready, otherwise continue to process it from our strparser
backlog.
Fixes: c46234ebb4 ("tls: RX path for ktls")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a447da7d00 ]
syzkaller managed to trigger a use-after-free in tls like the
following:
BUG: KASAN: use-after-free in tls_push_record.constprop.15+0x6a2/0x810 [tls]
Write of size 1 at addr ffff88037aa08000 by task a.out/2317
CPU: 3 PID: 2317 Comm: a.out Not tainted 4.17.0+ #144
Hardware name: LENOVO 20FBCTO1WW/20FBCTO1WW, BIOS N1FET47W (1.21 ) 11/28/2016
Call Trace:
dump_stack+0x71/0xab
print_address_description+0x6a/0x280
kasan_report+0x258/0x380
? tls_push_record.constprop.15+0x6a2/0x810 [tls]
tls_push_record.constprop.15+0x6a2/0x810 [tls]
tls_sw_push_pending_record+0x2e/0x40 [tls]
tls_sk_proto_close+0x3fe/0x710 [tls]
? tcp_check_oom+0x4c0/0x4c0
? tls_write_space+0x260/0x260 [tls]
? kmem_cache_free+0x88/0x1f0
inet_release+0xd6/0x1b0
__sock_release+0xc0/0x240
sock_close+0x11/0x20
__fput+0x22d/0x660
task_work_run+0x114/0x1a0
do_exit+0x71a/0x2780
? mm_update_next_owner+0x650/0x650
? handle_mm_fault+0x2f5/0x5f0
? __do_page_fault+0x44f/0xa50
? mm_fault_error+0x2d0/0x2d0
do_group_exit+0xde/0x300
__x64_sys_exit_group+0x3a/0x50
do_syscall_64+0x9a/0x300
? page_fault+0x8/0x30
entry_SYSCALL_64_after_hwframe+0x44/0xa9
This happened through fault injection where aead_req allocation in
tls_do_encryption() eventually failed and we returned -ENOMEM from
the function. Turns out that the use-after-free is triggered from
tls_sw_sendmsg() in the second tls_push_record(). The error then
triggers a jump to waiting for memory in sk_stream_wait_memory()
resp. returning immediately in case of MSG_DONTWAIT. What follows is
the trim_both_sgl(sk, orig_size), which drops elements from the sg
list added via tls_sw_sendmsg(). Now the use-after-free gets triggered
when the socket is being closed, where tls_sk_proto_close() callback
is invoked. The tls_complete_pending_work() will figure that there's
a pending closed tls record to be flushed and thus calls into the
tls_push_pending_closed_record() from there. ctx->push_pending_record()
is called from the latter, which is the tls_sw_push_pending_record()
from sw path. This again calls into tls_push_record(). And here the
tls_fill_prepend() will panic since the buffer address has been freed
earlier via trim_both_sgl(). One way to fix it is to move the aead
request allocation out of tls_do_encryption() early into tls_push_record().
This means we don't prep the tls header and advance state to the
TLS_PENDING_CLOSED_RECORD before allocation which could potentially
fail happened. That fixes the issue on my side.
Fixes: 3c4d755915 ("tls: kernel TLS support")
Reported-by: syzbot+5c74af81c547738e1684@syzkaller.appspotmail.com
Reported-by: syzbot+709f2810a6a05f11d4d3@syzkaller.appspotmail.com
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4fd44a98ff ]
commit 079096f103 ("tcp/dccp: install syn_recv requests into ehash
table") introduced an optimization for the handling of child sockets
created for a new TCP connection.
But this optimization passes any data associated with the last ACK of the
connection handshake up the stack without verifying its checksum, because it
calls tcp_child_process(), which in turn calls tcp_rcv_state_process()
directly. These lower-level processing functions do not do any checksum
verification.
Insert a tcp_checksum_complete call in the TCP_NEW_SYN_RECEIVE path to
fix this.
Fixes: 079096f103 ("tcp/dccp: install syn_recv requests into ehash table")
Signed-off-by: Frank van der Linden <fllinden@amazon.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Balbir Singh <bsingharora@gmail.com>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8d499533e0 ]
use nla_strlcpy() to avoid copying data beyond the length of TCA_DEF_DATA
netlink attribute, in case it is less than SIMP_MAX_DATA and it does not
end with '\0' character.
v2: fix errors in the commit message, thanks Hangbin Liu
Fixes: fa1b1cff3d ("net_cls_act: Make act_simple use of netlink policy.")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b718e8c8f4 ]
DP83620 register set is compatible with the DP83848, but it also supports
100base-FX. When the hardware is configured such as that fiber mode is
enabled, autonegotiation is not possible.
The chip, however, doesn't expose this information via BMSR_ANEGCAPABLE.
Instead, this bit is always set high, even if the particular hardware
configuration makes it so that auto negotiation is not possible [1]. Under
these circumstances, the phy subsystem keeps trying for autonegotiation to
happen, without success.
Hereby, we inspect BMCR_ANENABLE bit after genphy_config_init, which on
reset is set to 0 when auto negotiation is disabled, and so we use this
value instead of BMSR_ANEGCAPABLE.
[1] https://e2e.ti.com/support/interface/ethernet/f/903/p/697165/2571170
Signed-off-by: Alvaro Gamez Machado <alvaro.gamez@hazent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 349b71d6f4 ]
When pskb_trim_rcsum fails, the lack of error-handling code may
cause unexpected results.
This patch adds error-handling code after calling pskb_trim_rcsum.
Signed-off-by: Zhouyang Jia <jiazhouyang09@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0975764684 ]
IPVS setups with local client and remote tunnel server need
to create exception for the local virtual IP. What we do is to
change PMTU from 64KB (on "lo") to 1460 in the common case.
Suggested-by: Martin KaFai Lau <kafai@fb.com>
Fixes: 45e4fd2668 ("ipv6: Only create RTF_CACHE routes after encountering pmtu exception")
Fixes: 7343ff31eb ("ipv6: Don't create clones of host routes.")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: David Ahern <dsahern@gmail.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit eb55bbf865 ]
There is a timing issue under active-standy mode, when bond_enslave() is
called, bond->params.primary might not be initialized yet.
Any time the primary slave string changes, bond->force_primary should be
set to true to make sure the primary becomes the active slave.
Signed-off-by: Xiangning Yu <yuxiangning@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 58d813afbe upstream.
This was originally mistakenly submitted to net-next. Resubmitting to net.
The comparison of numvecs < 0 is always false because numvecs is a u32
and hence the error return from a failed call to pci_alloc_irq_vectores
is never detected. Fix this by using the signed int ret to handle the
error return and assign numvecs to err.
Detected by CoverityScan, CID#1468650 ("Unsigned compared against 0")
Fixes: a09bd81b54 ("net: aquantia: Limit number of vectors to actually allocated irqs")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Holger Hoffstätte <holger@applied-asynchrony.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 730f23b660 upstream.
In p8_aes_xts_init() we do a printk(KERN_INFO ...) to report the
fallback implementation we're using. However with a slow console this
can significantly affect the speed of crypto operations. So remove it.
Fixes: c07f5d3da6 ("crypto: vmx - Adding support for XTS")
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1411b5218a upstream.
In the vmx AES init routines we do a printk(KERN_INFO ...) to report
the fallback implementation we're using.
However with a slow console this can significantly affect the speed of
crypto operations. Using 'cryptsetup benchmark' the removal of the
printk() leads to a ~5x speedup for aes-cbc decryption.
So remove them.
Fixes: 8676590a15 ("crypto: vmx - Adding AES routines for VMX module")
Fixes: 8c755ace35 ("crypto: vmx - Adding CBC routines for VMX module")
Fixes: 4f7f60d312 ("crypto: vmx - Adding CTR routines for VMX module")
Fixes: cc333cd68d ("crypto: vmx - Adding GHASH routines for VMX module")
Cc: stable@vger.kernel.org # v4.1+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c782a8c43e upstream.
After issuing a request an endless loop was used to read the
completion state from memory which is asynchronously updated
by the ZIP coprocessor.
Add an upper bound to the retry attempts to prevent a CPU getting stuck
forever in case of an error. Additionally, add a read memory barrier
and a small delay between the reading attempts.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Reviewed-by: Robert Richter <rrichter@cavium.com>
Cc: stable <stable@vger.kernel.org> # 4.14
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 37ff02acaa upstream.
Enabling virtual mapped kernel stacks breaks the thunderx_zip
driver. On compression or decompression the executing CPU hangs
in an endless loop. The reason for this is the usage of __pa
by the driver which does no longer work for an address that is
not part of the 1:1 mapping.
The zip driver allocates a result struct on the stack and needs
to tell the hardware the physical address within this struct
that is used to signal the completion of the request.
As the hardware gets the wrong address after the broken __pa
conversion it writes to an arbitrary address. The zip driver then
waits forever for the completion byte to contain a non-zero value.
Allocating the result struct from 1:1 mapped memory resolves this
bug.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Reviewed-by: Robert Richter <rrichter@cavium.com>
Cc: stable <stable@vger.kernel.org> # 4.14
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a488aaec6 upstream.
There are two IV-related issues:
(1) crypto API does not guarantee to provide an IV buffer that is DMAable,
thus it's incorrect to DMA map it
(2) for in-place decryption, since ciphertext is overwritten with
plaintext, updated IV (req->info) will contain the last block of plaintext
(instead of the last block of ciphertext)
While these two issues could be fixed separately, it's straightforward
to fix both in the same time - by using the {ablkcipher,aead}_edesc
extended descriptor to store the IV that will be fed to the crypto engine;
this allows for fixing (2) by saving req->src[last_block] in req->info
directly, i.e. without allocating yet another temporary buffer.
A side effect of the fix is that it's no longer possible to have the IV
contiguous with req->src or req->dst.
Code checking for this case is removed.
Cc: <stable@vger.kernel.org> # 4.14+
Fixes: a68a193805 ("crypto: caam/qi - properly set IV after {en,de}crypt")
Link: http://lkml.kernel.org/r/20170113084620.GF22022@gondor.apana.org.au
Reported-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 115957bb3e upstream.
There are two IV-related issues:
(1) crypto API does not guarantee to provide an IV buffer that is DMAable,
thus it's incorrect to DMA map it
(2) for in-place decryption, since ciphertext is overwritten with
plaintext, updated req->info will contain the last block of plaintext
(instead of the last block of ciphertext)
While these two issues could be fixed separately, it's straightforward
to fix both in the same time - by allocating extra space in the
ablkcipher_edesc for the IV that will be fed to the crypto engine;
this allows for fixing (2) by saving req->src[last_block] in req->info
directly, i.e. without allocating another temporary buffer.
A side effect of the fix is that it's no longer possible to have the IV
and req->src contiguous. Code checking for this case is removed.
Cc: <stable@vger.kernel.org> # 4.13+
Fixes: 854b06f768 ("crypto: caam - properly set IV after {en,de}crypt")
Link: http://lkml.kernel.org/r/20170113084620.GF22022@gondor.apana.org.au
Reported-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 281a58c832 upstream.
The product signature and HW revision register have different offset on the
older HW revisions.
This fixes the problem of the driver failing sanity check on silicon
despite working on the FPGA emulation systems.
Fixes: 27b3b22dd9 ("crypto: ccree - add support for older HW revs")
Cc: stable@vger.kernel.org
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a7e625ce5 upstream.
Commit 9b96fbacda ("serial: PL011: clear pending interrupts")
clears the RX and receive timeout interrupts on pl011 startup, to
avoid a screaming-interrupt scenario that can occur when the
firmware or bootloader leaves these interrupts asserted.
This has been noted as an issue when running Linux on qemu [1].
Unfortunately, the above fix seems to lead to potential
misbehaviour if the RX FIFO interrupt is asserted _non_ spuriously
on driver startup, if the RX FIFO is also already full to the
trigger level.
Clearing the RX FIFO interrupt does not change the FIFO fill level.
In this scenario, because the interrupt is now clear and because
the FIFO is already full to the trigger level, no new assertion of
the RX FIFO interrupt can occur unless the FIFO is drained back
below the trigger level. This never occurs because the pl011
driver is waiting for an RX FIFO interrupt to tell it that there is
something to read, and does not read the FIFO at all until that
interrupt occurs.
Thus, simply clearing "spurious" interrupts on startup may be
misguided, since there is no way to be sure that the interrupts are
truly spurious, and things can go wrong if they are not.
This patch instead clears the interrupt condition by draining the
RX FIFO during UART startup, after clearing any potentially
spurious interrupt. This should ensure that an interrupt will
definitely be asserted if the RX FIFO subsequently becomes
sufficiently full.
The drain is done at the point of enabling interrupts only. This
means that it will occur any time the UART is newly opened through
the tty layer. It will not apply to polled-mode use of the UART by
kgdboc: since that scenario cannot use interrupts by design, this
should not matter. kgdboc will interact badly with "normal" use of
the UART in any case: this patch makes no attempt to paper over
such issues.
This patch does not attempt to address the case where the RX FIFO
fills faster than it can be drained: that is a pathological
hardware design problem that is beyond the scope of the driver to
work around. As a failsafe, the number of poll iterations for
draining the FIFO is limited to twice the FIFO size. This will
ensure that the kernel at least boots even if it is impossible to
drain the FIFO for some reason.
[1] [Qemu-devel] [Qemu-arm] [PATCH] pl011: do not put into fifo
before enabled the interruption
https://lists.gnu.org/archive/html/qemu-devel/2018-01/msg06446.html
Reported-by: Wei Xu <xuwei5@hisilicon.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Peter Maydell <peter.maydell@linaro.org>
Fixes: 9b96fbacda ("serial: PL011: clear pending interrupts")
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Cc: stable <stable@vger.kernel.org>
Tested-by: Wei Xu <xuwei5@hisilicon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f59acbc5e0 upstream.
In 4.9 kernel, the sysfs files for Hyper-V VMBus changed name but
the documentation files were not updated. The current sysfs file
names are /sys/bus/vmbus/devices/<UUID>/...
See commit 9a56e5d6a0ba ("Drivers: hv: make VMBus bus ids persistent")
and commit f6b2db084b ("vmbus: make sysfs names consistent with PCI")
Reported-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Cc: stable@vger.kernel.org
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 13dc04d0e5 upstream.
I noticed that unused UARTs won't necessarily idle properly always
unless at least one byte tx transfer is done first.
After some debugging I narrowed down the problem to the scr register
dma configuration bits that need to be set before softreset for the
clocks to idle. Unless we do this, the module clkctrl idlest bits
may be set to 1 instead of 3 meaning the clock will never idle and
is blocking deeper idle states for the whole domain.
This might be related to the configuration done by the bootloader
or kexec booting where certain configurations cause the 8250 or
the clkctrl clock to jam in a way where setting of the scr bits
and reset is needed to clear it. I've tried diffing the 8250
registers for the various modes, but did not see anything specific.
So far I've only seen this on omap4 but I'm suspecting this might
also happen on the other clkctrl using SoCs considering they
already have a quirk enabled for UART_ERRATA_CLOCK_DISABLE.
Let's fix the issue by configuring scr before reset for basic dma
even if we don't use it. The scr register will be reset when we do
softreset few lines after, and we restore scr on resume. We should
do this for all the SoCs with UART_ERRATA_CLOCK_DISABLE quirk flag
set since the ones with UART_ERRATA_CLOCK_DISABLE are all based
using clkctrl similar to omap4.
Looks like both OMAP_UART_SCR_DMAMODE_1 | OMAP_UART_SCR_DMAMODE_CTL
bits are needed for the clkctrl to idle after a softreset.
And we need to add omap4 to also use the UART_ERRATA_CLOCK_DISABLE
for the related workaround to be enabled. This same compatible
value will also be used for omap5.
Fixes: cdb929e445 ("serial: 8250_omap: workaround errata around idling UART after using DMA")
Cc: Keerthy <j-keerthy@ti.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aa2f80e752 upstream.
The best granularity of residue that DMA engine can report is in the BURST
units, so the serial driver must use MAXBURST = 1 and DMA_SLAVE_BUSWIDTH_1_BYTE
if it relies on exact number of bytes transferred by DMA engine.
Fixes: 62c37eedb7 ("serial: samsung: add dma reqest/release functions")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9594b5be7e upstream.
I was puzzled while looking at /proc/interrupts and random things showed
up between reboots. This occurred more often but I realised it later. The
"correct" output should be:
|38: 11861 atmel-aic5 2 Level ttyS0
but I saw sometimes
|38: 6426 atmel-aic5 2 Level tty1
and accounted it wrongly as correct. This is use after free and the
former example randomly got the "old" pointer which pointed to the same
content. With SLAB_FREELIST_RANDOM and HARDENED I even got
|38: 7067 atmel-aic5 2 Level E=Started User Manager for UID 0
or other nonsense.
As it turns out the tty, pointer that is accessed in atmel_startup(), is
freed() before atmel_shutdown(). It seems to happen quite often that the
tty for ttyS0 is allocated and freed while ->shutdown is not invoked. I
don't do anything special - just a systemd boot :)
Use dev_name(&pdev->dev) as the IRQ name for request_irq(). This exists
as long as the driver is loaded so no use-after-free here.
Cc: stable@vger.kernel.org
Fixes: 761ed4a945 ("tty: serial_core: convert uart_close to use tty_port_close")
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 003bc1dee2 upstream.
This patch fixes an issue that this driver cannot call phy_init()
if a gadget driver is alreadly loaded because usb_add_gadget_udc()
might call renesas_usb3_start() via .udc_start.
This patch also revises the typo (s/an optional/optional/).
Fixes: 279d4bc640 ("usb: gadget: udc: renesas_usb3: add support for generic phy")
Cc: <stable@vger.kernel.org> # v4.15+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d998844016 upstream.
This patch fixes an issue that this driver causes panic if a gadget
driver is already loaded because usb_add_gadget_udc() might call
renesas_usb3_start() via .udc_start, and then pm_runtime_get_sync()
in renesas_usb3_start() doesn't work correctly.
Note that the usb3_to_dev() macro should not be called at this timing
because the macro uses the gadget structure.
Fixes: cf06df3fae ("usb: gadget: udc: renesas_usb3: move pm_runtime_{en,dis}able()")
Cc: <stable@vger.kernel.org> # v4.15+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a014a7339 upstream.
When printer_write() calls usb_ep_queue(), a udc driver (e.g.
renesas_usbhs driver) may call usb_gadget_giveback_request() in
the udc .queue ops immediately. Then, printer_write() calls
list_add(&req->list, &dev->tx_reqs_active) wrongly. After that,
if we do unbind the printer driver, WARN_ON() happens in
printer_func_unbind() because the list entry is not removed.
So, this patch moves list_add(&req->list, &dev->tx_reqs_active)
calling before usb_ep_queue().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05826ff135 upstream.
The USB Type-C PHY in Intel WhiskeyCove PMIC has build-in
USB Type-C state machine which we were relying on to
configure the CC lines correctly. This patch removes that
dependency and configures the CC line according to commands
from the port manager (tcpm.c) in wcove_set_cc().
This fixes an issue where USB devices attached to the USB
Type-C port do not get enumerated. When acting as
source/host, the HW FSM sometimes fails to configure the PHY
correctly.
Fixes: 3c4fb9f169 ("usb: typec: wcove: start using tcpm for USB PD support")
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0b4555e776 upstream.
Driver currently crashes due to NULL pointer deference
while updating PHY tune register if nvmem cell is NULL.
Since, fused value for Tune1/2 register is optional,
we'd rather bail out.
Fixes: ca04d9d3e1 ("phy: qcom-qusb2: New driver for QUSB2 PHY on Qcom chips")
Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Cc: stable <stable@vger.kernel.org> # 4.14+
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c4e97ddfe upstream.
The ALWAYS_SYNC flag is currently honored by the usb-storage driver but not UAS
and is required to work around devices that become unstable upon being
queried for cache. This code is taken straight from:
drivers/usb/storage/scsiglue.c:284
Signed-off-by: Alexander Kappner <agk@godking.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a0d6ec8809 upstream.
pdev_nr and rhport can be controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/usb/usbip/vhci_sysfs.c:238 detach_store() warn: potential spectre issue 'vhcis'
drivers/usb/usbip/vhci_sysfs.c:328 attach_store() warn: potential spectre issue 'vhcis'
drivers/usb/usbip/vhci_sysfs.c:338 attach_store() warn: potential spectre issue 'vhci->vhci_hcd_ss->vdev'
drivers/usb/usbip/vhci_sysfs.c:340 attach_store() warn: potential spectre issue 'vhci->vhci_hcd_hs->vdev'
Fix this by sanitizing pdev_nr and rhport before using them to index
vhcis and vhci->vhci_hcd_ss->vdev respectively.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dbafc28955 upstream.
It's amazing that this driver ever worked, but now that x86 doesn't
allow USB data to be sent off of the stack, it really does not work at
all. Fix this up by properly allocating the data for the small
"commands" that get sent to the device off of the stack.
We do this for one command by having a whole urb just for ack messages,
as they can be submitted in interrupt context, so we can not use
usb_bulk_msg(). But the poweron command can sleep (and does), so use
usb_bulk_msg() for that transfer.
Reported-by: Carlos Manuel Santos <cmmpsantos@gmail.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45ad559a29 upstream.
Syzbot reported yet another warning with Ion:
WARNING: CPU: 0 PID: 1467 at drivers/staging/android/ion/ion.c:122
ion_buffer_destroy+0xd4/0x190 drivers/staging/android/ion/ion.c:122
Kernel panic - not syncing: panic_on_warn set ...
This is catching that a buffer was freed with an existing kernel mapping
still present. This can be easily be triggered from userspace by calling
DMA_BUF_SYNC_START without calling DMA_BUF_SYNC_END. Switch to a single
pr_warn_once to indicate the error without being disruptive.
Reported-by: syzbot+cd8bcd40cb049efa2770@syzkaller.appspotmail.com
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c9fa24ca7 upstream.
The functions that were used in the emulation of fxrstor, fxsave, sgdt and
sidt were originally meant for task switching, and as such they did not
check privilege levels. This is very bad when the same functions are used
in the emulation of unprivileged instructions. This is CVE-2018-10853.
The obvious fix is to add a new argument to ops->read_std and ops->write_std,
which decides whether the access is a "system" access or should use the
processor's CPL.
Fixes: 129a72a0d3 ("KVM: x86: Introduce segmented_write_std", 2017-01-12)
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce14e868a5 upstream.
Int the next patch the emulator's .read_std and .write_std callbacks will
grow another argument, which is not needed in kvm_read_guest_virt and
kvm_write_guest_virt_system's callers. Since we have to make separate
functions, let's give the currently existing names a nicer interface, too.
Fixes: 129a72a0d3 ("KVM: x86: Introduce segmented_write_std", 2017-01-12)
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 727ba748e1 upstream.
VMX instructions executed inside a L1 VM will always trigger a VM exit
even when executed with cpl 3. This means we must perform the
privilege check in software.
Fixes: 70f3aac964ae("kvm: nVMX: Remove superfluous VMX instruction fault checks")
Cc: stable@vger.kernel.org
Signed-off-by: Felix Wilhelm <fwilhelm@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 766d3571d8 upstream.
KVM_X86_DISABLE_EXITS_HTL really refers to exit on halt.
Obviously a typo: should be named KVM_X86_DISABLE_EXITS_HLT.
Fixes: caa057a2ca ("KVM: X86: Provide a capability to disable HLT intercepts")
Cc: stable@vger.kernel.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 79367a6574 upstream.
Wrap the common invocation of ctxt->ops->read_std and ctxt->ops->write_std, so
as to have a smaller patch when the functions grow another argument.
Fixes: 129a72a0d3 ("KVM: x86: Introduce segmented_write_std", 2017-01-12)
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a780a3ea62 upstream.
MSB of CR3 is a reserved bit if the PCIDE bit is not set in CR4.
It should be checked when PCIDE bit is not set, however commit
'd1cd3ce900441 ("KVM: MMU: check guest CR3 reserved bits based on
its physical address width")' removes the bit 63 checking
unconditionally. This patch fixes it by checking bit 63 of CR3
when PCIDE bit is not set in CR4.
Fixes: d1cd3ce900 (KVM: MMU: check guest CR3 reserved bits based on its physical address width)
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Liran Alon <liran.alon@oracle.com>
Cc: stable@vger.kernel.org
Reviewed-by: Junaid Shahid <junaids@google.com>
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 327ea4adcf upstream.
Avoid that complaints similar to the following appear in the kernel log
if the number of zones is sufficiently large:
fio: page allocation failure: order:9, mode:0x140c0c0(GFP_KERNEL|__GFP_COMP|__GFP_ZERO), nodemask=(null)
Call Trace:
dump_stack+0x63/0x88
warn_alloc+0xf5/0x190
__alloc_pages_slowpath+0x8f0/0xb0d
__alloc_pages_nodemask+0x242/0x260
alloc_pages_current+0x6a/0xb0
kmalloc_order+0x18/0x50
kmalloc_order_trace+0x26/0xb0
__kmalloc+0x20e/0x220
blkdev_report_zones_ioctl+0xa5/0x1a0
blkdev_ioctl+0x1ba/0x930
block_ioctl+0x41/0x50
do_vfs_ioctl+0xaa/0x610
SyS_ioctl+0x79/0x90
do_syscall_64+0x79/0x1b0
entry_SYSCALL_64_after_hwframe+0x3d/0xa2
Fixes: 3ed05a987e ("blk-zoned: implement ioctls")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Shaun Tancheff <shaun.tancheff@seagate.com>
Cc: Damien Le Moal <damien.lemoal@hgst.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c826fed67 upstream.
-Tx request and data is copied to HW Q in 64B desc, check for
end of queue and adjust the current position to start from
beginning before passing the additional request info.
-key context copy should check key length only
-Few reverse christmas tree correction
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c3635da2a3 upstream.
Before the guest finishes the device initialization, the device can be
removed anytime by the host, and after that the host won't respond to
the guest's request, so the guest should be prepared to handle this
case.
Add a polling mechanism to detect device presence.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
[lorenzo.pieralisi@arm.com: edited commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e783bb00ad ]
commit 0bbbf0e7d0 ("ipmr, ip6mr: Unite creation of new mr_table")
refactored ipmr_new_table, so that it now returns NULL when
mr_table_alloc fails. Unfortunately, all callers of ipmr_new_table
expect an ERR_PTR.
This can result in NULL deref, for example when ipmr_rules_exit calls
ipmr_free_table with NULL net->ipv4.mrt in the
!CONFIG_IP_MROUTE_MULTIPLE_TABLES version.
This patch makes mr_table_alloc return errors, and changes
ip6mr_new_table and its callers to return/expect error pointers as
well. It also removes the version of mr_table_alloc defined under
!CONFIG_IP_MROUTE_COMMON, since it is never used.
Fixes: 0bbbf0e7d0 ("ipmr, ip6mr: Unite creation of new mr_table")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5040cc990c ]
In the Broadcom Cygnus SoC, the brcm tag needs to be inserted
in between the mac address and the ether type (should use
'DSA_PROTO_TAG_BRCM') for the packets sent to the internal
b53 switch.
Since the Cygnus was added with the BCM58XX device id and the
BCM58XX uses 'DSA_PROTO_TAG_BRCM_PREPEND', the data path is
broken, due to the incorrect brcm tag location.
Add a new b53 device id (BCM583XX) for Cygnus family to fix the
issue. Add the new device id to the BCM58XX family as Cygnus
is similar to the BCM58XX in most other functionalities.
Fixes: 1160603960 ("net: dsa: b53: Support prepended Broadcom tags")
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Reported-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2f17becfbe ]
Use the right device to determine if redirect should be sent especially
when using vrf. Same as well as when sending the redirect.
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 25ea66544b ]
This code was introduced in 2011 around the same time that we made
netdev_features_t a u64 type. These days a u32 is not big enough to
hold all the potential features.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1d88ba1ebb ]
syzbot reported a rcu_sched self-detected stall on CPU which is caused
by too small value set on rto_min with SCTP_RTOINFO sockopt. With this
value, hb_timer will get stuck there, as in its timer handler it starts
this timer again with this value, then goes to the timer handler again.
This problem is there since very beginning, and thanks to Eric for the
reproducer shared from a syzbot mail.
This patch fixes it by not allowing sctp_transport_timeout to return a
smaller value than HZ/5 for hb_timer, which is based on TCP's min rto.
Note that it doesn't fix this issue by limiting rto_min, as some users
are still using small rto and no proper value was found for it yet.
Reported-by: syzbot+3dcd59a1f907245f891f@syzkaller.appspotmail.com
Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 75d4e704fa ]
Per discussion with David at netconf 2018, let's clarify
DaveM's position of handling stable backports in netdev-FAQ.
This is important for people relying on upstream -stable
releases.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3d609342cc ]
Commit d02ba2a611 ("l2tp: fix race in pppol2tp_release with session
object destroy") tried to fix a race condition where a PPPoL2TP socket
would disappear while the L2TP session was still using it. However, it
missed the root issue which is that an L2TP session may accept to be
reconnected if its associated socket has entered the release process.
The tentative fix makes the session hold the socket it is connected to.
That saves the kernel from crashing, but introduces refcount leakage,
preventing the socket from completing the release process. Once stalled,
everything the socket depends on can't be released anymore, including
the L2TP session and the l2tp_ppp module.
The root issue is that, when releasing a connected PPPoL2TP socket, the
session's ->sk pointer (RCU-protected) is reset to NULL and we have to
wait for a grace period before destroying the socket. The socket drops
the session in its ->sk_destruct callback function, so the session
will exist until the last reference on the socket is dropped.
Therefore, there is a time frame where pppol2tp_connect() may accept
reconnecting a session, as it only checks ->sk to figure out if the
session is connected. This time frame is shortened by the fact that
pppol2tp_release() calls l2tp_session_delete(), making the session
unreachable before resetting ->sk. However, pppol2tp_connect() may
grab the session before it gets unhashed by l2tp_session_delete(), but
it may test ->sk after the later got reset. The race is not so hard to
trigger and syzbot found a pretty reliable reproducer:
https://syzkaller.appspot.com/bug?id=418578d2a4389074524e04d641eacb091961b2cf
Before d02ba2a611, another race could let pppol2tp_release()
overwrite the ->__sk pointer of an L2TP session, thus tricking
pppol2tp_put_sk() into calling sock_put() on a socket that is different
than the one for which pppol2tp_release() was originally called. To get
there, we had to trigger the race described above, therefore having one
PPPoL2TP socket being released, while the session it is connected to is
reconnecting to a different PPPoL2TP socket. When releasing this new
socket fast enough, pppol2tp_release() overwrites the session's
->__sk pointer with the address of the new socket, before the first
pppol2tp_put_sk() call gets scheduled. Then the pppol2tp_put_sk() call
invoked by the original socket will sock_put() the new socket,
potentially dropping its last reference. When the second
pppol2tp_put_sk() finally runs, its socket has already been freed.
With d02ba2a611, the session takes a reference on both sockets.
Furthermore, the session's ->sk pointer is reset in the
pppol2tp_session_close() callback function rather than in
pppol2tp_release(). Therefore, ->__sk can't be overwritten and
pppol2tp_put_sk() is called only once (l2tp_session_delete() will only
run pppol2tp_session_close() once, to protect the session against
concurrent deletion requests). Now pppol2tp_put_sk() will properly
sock_put() the original socket, but the new socket will remain, as
l2tp_session_delete() prevented the release process from completing.
Here, we don't depend on the ->__sk race to trigger the bug. Getting
into the pppol2tp_connect() race is enough to leak the reference, no
matter when new socket is released.
So it all boils down to pppol2tp_connect() failing to realise that the
session has already been connected. This patch drops the unneeded extra
reference counting (mostly reverting d02ba2a611) and checks that
neither ->sk nor ->__sk is set before allowing a session to be
connected.
Fixes: d02ba2a611 ("l2tp: fix race in pppol2tp_release with session object destroy")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fa1be7e01e ]
Some of the code paths calculating flow hash for IPv6 use flowlabel member
of struct flowi6 which, despite its name, encodes both flow label and
traffic class. If traffic class changes within a TCP connection (as e.g.
ssh does), ECMP route can switch between path. It's also inconsistent with
other code paths where ip6_flowlabel() (returning only flow label) is used
to feed the key.
Use only flow label everywhere, including one place where hash key is set
using ip6_flowinfo().
Fixes: 51ebd31815 ("ipv6: add support of equal cost multipath (ECMP)")
Fixes: f70ea018da ("net: Add functions to get skb->hash based on flow structures")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 848235edb5 ]
Currently, raw6_sk(sk)->ip6mr_table is set unconditionally during
ip6_mroute_setsockopt(MRT6_TABLE). A subsequent attempt at the same
setsockopt will fail with -ENOENT, since we haven't actually created
that table.
A similar fix for ipv4 was included in commit 5e1859fbcc ("ipv4: ipmr:
various fixes and cleanups").
Fixes: d1db275dd3 ("ipv6: ip6mr: support multiple tables")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dd612f18a4 ]
Nearby code that also tests port suggests that the P0 constant should be
used when port is zero.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e,e1;
@@
* e ? e1 : e1
// </smpl>
Fixes: 6c3218c6f7 ("bnx2x: Adjust ETS to 578xx")
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a79fd3908 upstream.
Some drivers, such as vxlan and wireguard, use the skb's dst in order to
determine things like PMTU. They therefore loose functionality when flow
offloading is enabled. So, we ensure the skb has it before xmit'ing it
in the offloading path.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-06-11 22:43:17 +02:00
2127 changed files with 298194 additions and 10848 deletions
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
