The panel sends MIPI DCS commands during prepare and is expecting
the bus to remain in LP-11 state in-between.
Set the prepare_upstream_first flag so that the upstream DSI host
is prepared / pre_enabled first, and therefore the bus is in a
defined state.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
mipi_dsi_attach is allowed to fail, and currently the probe
code doesn't clean up (mainly drm_panel_remove) if this happens.
Add cleanup code on failure.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
There is no specific AArch32 driver for the Cortex-A72 PMU, but the
Cortex-A7 one works and is much better than no PMU driver at all.
Signed-off-by: Ben Avison <bavison@riscosopen.org>
Allowing GPIO state to persist allows the use of gpioset to control
GPIO levels without having to use the --mode=wait feature.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
On some platforms the cma area can be half the entire system memory,
meaning that allocations start happening in the cma area immediately.
This leads to fragmentation and subsequent fatal cma_alloc failures.
We introduce an "alloc_in_cma_threshold" parameter which requires that
this many sixteenths of the free pages must be in cma before it will
try to use them. By default this is set to 12, but the previous
behaviour can be restored by setting it to 8 on startup.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
commit 8926d88ced upstream.
The get_user()/put_user() functions are meant to check for
access_ok(), while the __get_user()/__put_user() functions
don't.
This broke in 4.19 for nds32, when it gained an extraneous
check in __get_user(), but lost the check it needs in
__put_user().
Fixes: 487913ab18 ("nds32: Extract the checking and getting pointer to a macro")
Cc: stable@vger.kernel.org @ v4.19+
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26509034be upstream.
While most m68k platforms use separate address spaces for user
and kernel space, at least coldfire does not, and the other
ones have a TASK_SIZE that is less than the entire 4GB address
range.
Using the default implementation of __access_ok() stops coldfire
user space from trivially accessing kernel memory.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb5abce6b2 upstream.
As part of the series conversion to remove nested TPM operations:
https://lore.kernel.org/all/20190205224723.19671-1-jarkko.sakkinen@linux.intel.com/
exposure of the chip->tpm_mutex was removed from much of the upper
level code. In this conversion, tpm2_del_space() was missed. This
didn't matter much because it's usually called closely after a
converted operation, so there's only a very tiny race window where the
chip can be removed before the space flushing is done which causes a
NULL deref on the mutex. However, there are reports of this window
being hit in practice, so fix this by converting tpm2_del_space() to
use tpm_try_get_ops(), which performs all the teardown checks before
acquring the mutex.
Cc: stable@vger.kernel.org # 5.4.x
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a2d4496e1 upstream.
While commit 6a01afcf84 ("mac80211: mesh: Free ie data when leaving
mesh") fixed a memory leak on mesh leave / teardown it introduced a
potential memory corruption caused by a double free when rejoining the
mesh:
ieee80211_leave_mesh()
-> kfree(sdata->u.mesh.ie);
...
ieee80211_join_mesh()
-> copy_mesh_setup()
-> old_ie = ifmsh->ie;
-> kfree(old_ie);
This double free / kernel panics can be reproduced by using wpa_supplicant
with an encrypted mesh (if set up without encryption via "iw" then
ifmsh->ie is always NULL, which avoids this issue). And then calling:
$ iw dev mesh0 mesh leave
$ iw dev mesh0 mesh join my-mesh
Note that typically these commands are not used / working when using
wpa_supplicant. And it seems that wpa_supplicant or wpa_cli are going
through a NETDEV_DOWN/NETDEV_UP cycle between a mesh leave and mesh join
where the NETDEV_UP resets the mesh.ie to NULL via a memcpy of
default_mesh_setup in cfg80211_netdev_notifier_call, which then avoids
the memory corruption, too.
The issue was first observed in an application which was not using
wpa_supplicant but "Senf" instead, which implements its own calls to
nl80211.
Fixing the issue by removing the kfree()'ing of the mesh IE in the mesh
join function and leaving it solely up to the mesh leave to free the
mesh IE.
Cc: stable@vger.kernel.org
Fixes: 6a01afcf84 ("mac80211: mesh: Free ie data when leaving mesh")
Reported-by: Matthias Kretschmer <mathias.kretschmer@fit.fraunhofer.de>
Signed-off-by: Linus Lüssing <ll@simonwunderlich.de>
Tested-by: Mathias Kretschmer <mathias.kretschmer@fit.fraunhofer.de>
Link: https://lore.kernel.org/r/20220310183513.28589-1-linus.luessing@c0d3.blue
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 222ca305c9 upstream.
Three architectures check the end of a user access against the
address limit without taking a possible overflow into account.
Passing a negative length or another overflow in here returns
success when it should not.
Use the most common correct implementation here, which optimizes
for a constant 'size' argument, and turns the common case into a
single comparison.
Cc: stable@vger.kernel.org
Fixes: da55128194 ("csky: User access")
Fixes: f663b60f52 ("microblaze: Fix uaccess_ok macro")
Fixes: 7567746e1c ("Hexagon: Add user access functions")
Reported-by: David Laight <David.Laight@aculab.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 10c5357874 upstream.
Currently rcu_preempt_deferred_qs_irqrestore() releases rnp->boost_mtx
before reporting the expedited quiescent state. Under heavy real-time
load, this can result in this function being preempted before the
quiescent state is reported, which can in turn prevent the expedited grace
period from completing. Tim Murray reports that the resulting expedited
grace periods can take hundreds of milliseconds and even more than one
second, when they should normally complete in less than a millisecond.
This was fine given that there were no particular response-time
constraints for synchronize_rcu_expedited(), as it was designed
for throughput rather than latency. However, some users now need
sub-100-millisecond response-time constratints.
This patch therefore follows Neeraj's suggestion (seconded by Tim and
by Uladzislau Rezki) of simply reversing the two operations.
Reported-by: Tim Murray <timmurray@google.com>
Reported-by: Joel Fernandes <joelaf@google.com>
Reported-by: Neeraj Upadhyay <quic_neeraju@quicinc.com>
Reviewed-by: Neeraj Upadhyay <quic_neeraju@quicinc.com>
Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com>
Tested-by: Tim Murray <timmurray@google.com>
Cc: Todd Kjos <tkjos@google.com>
Cc: Sandeep Patil <sspatil@google.com>
Cc: <stable@vger.kernel.org> # 5.4.x
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8893d27ffc upstream.
The implementations of aead and skcipher in the QAT driver do not
support properly requests with the CRYPTO_TFM_REQ_MAY_BACKLOG flag set.
If the HW queue is full, the driver returns -EBUSY but does not enqueue
the request.
This can result in applications like dm-crypt waiting indefinitely for a
completion of a request that was never submitted to the hardware.
To avoid this problem, disable the registration of all crypto algorithms
in the QAT driver by setting the number of crypto instances to 0 at
configuration time.
Cc: stable@vger.kernel.org
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c844d22fe0 upstream.
Clevo NL5xRU and NL5xNU/TUXEDO Aura 15 Gen1 and Gen2 have both a working
native and video interface. However the default detection mechanism first
registers the video interface before unregistering it again and switching
to the native interface during boot. This results in a dangling SBIOS
request for backlight change for some reason, causing the backlight to
switch to ~2% once per boot on the first power cord connect or disconnect
event. Setting the native interface explicitly circumvents this buggy
behaviour by avoiding the unregistering process.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7dacee0b9e upstream.
For some reason, the Microsoft Surface Go 3 uses the standard ACPI
interface for battery information, but does not use the standard PNP0C0A
HID. Instead it uses MSHW0146 as identifier. Add that ID to the driver
as this seems to work well.
Additionally, the power state is not updated immediately after the AC
has been (un-)plugged, so add the respective quirk for that.
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e702196bf8 upstream.
On this board the ACPI RSDP structure points to both a RSDT and an XSDT,
but the XSDT points to a truncated FADT. This causes all sorts of trouble
and usually a complete failure to boot after the following error occurs:
ACPI Error: Unsupported address space: 0x20 (*/hwregs-*)
ACPI Error: AE_SUPPORT, Unable to initialize fixed events (*/evevent-*)
ACPI: Unable to start ACPI Interpreter
This leaves the ACPI implementation in such a broken state that subsequent
kernel subsystem initialisations go wrong, resulting in among others
mismapped PCI memory, SATA and USB enumeration failures, and freezes.
As this is an older embedded platform that will likely never see any BIOS
updates to address this issue and its default shipping OS only complies to
ACPI 1.0, work around this by forcing `acpi=rsdt`. This patch, applied on
top of Linux 5.10.102, was confirmed on real hardware to fix the issue.
Signed-off-by: Mark Cilissen <mark@yotsuba.nl>
Cc: All applicable <stable@vger.kernel.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e1acfa387 upstream.
Bail out in case userspace uses unsupported registers.
Fixes: 49499c3e6e ("netfilter: nf_tables: switch registers to 32 bit addressing")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9e6faeafa upstream.
All packets on ingress (except for jumbo) are terminated with a 4-bytes
CRC checksum. It's the responsability of the driver to strip those 4
bytes. Unfortunately a change dating back to March 2017 re-shuffled some
code and made the CRC stripping code effectively dead.
This change re-orders that part a bit such that the datalen is
immediately altered if needed.
Fixes: 4902a92270 ("drivers: net: xgene: Add workaround for errata 10GE_8/ENET_11")
Cc: stable@vger.kernel.org
Signed-off-by: Stephane Graber <stgraber@ubuntu.com>
Tested-by: Stephane Graber <stgraber@ubuntu.com>
Link: https://lore.kernel.org/r/20220322224205.752795-1-stgraber@ubuntu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 17aaf01933 upstream.
Tests 72 and 78 for ALSA in kselftest fail due to reading
inconsistent values from some devices on a VirtualBox
Virtual Machine using the snd_intel8x0 driver for the AC'97
Audio Controller device.
Taking for example test number 72, this is what the test reports:
"Surround Playback Volume.0 expected 1 but read 0, is_volatile 0"
"Surround Playback Volume.1 expected 0 but read 1, is_volatile 0"
These errors repeat for each value from 0 to 31.
Taking a look at these error messages it is possible to notice
that the written values are read back swapped.
When the write is performed, these values are initially stored in
an array used to sanity-check them and write them in the pcmreg
array. To write them, the two one-byte values are packed together
in a two-byte variable through bitwise operations: the first
value is shifted left by one byte and the second value is stored in the
right byte through a bitwise OR. When reading the values back,
right shifts are performed to retrieve the previously stored
bytes. These shifts are executed in the wrong order, thus
reporting the values swapped as shown above.
This patch fixes this mistake by reversing the read
operations' order.
Signed-off-by: Giacomo Guiduzzi <guiduzzi.giacomo@gmail.com>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220322200653.15862-1-guiduzzi.giacomo@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c3201f8c7 upstream.
Like the previous fixes to hw_params and hw_free ioctl races, we need
to paper over the concurrent prepare ioctl calls against hw_params and
hw_free, too.
This patch implements the locking with the existing
runtime->buffer_mutex for prepare ioctls. Unlike the previous case
for snd_pcm_hw_hw_params() and snd_pcm_hw_free(), snd_pcm_prepare() is
performed to the linked streams, hence the lock can't be applied
simply on the top. For tracking the lock in each linked substream, we
modify snd_pcm_action_group() slightly and apply the buffer_mutex for
the case stream_lock=false (formerly there was no lock applied)
there.
Cc: <stable@vger.kernel.org>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20220322170720.3529-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dca947d4d2 upstream.
In the current PCM design, the read/write syscalls (as well as the
equivalent ioctls) are allowed before the PCM stream is running, that
is, at PCM PREPARED state. Meanwhile, we also allow to re-issue
hw_params and hw_free ioctl calls at the PREPARED state that may
change or free the buffers, too. The problem is that there is no
protection against those mix-ups.
This patch applies the previously introduced runtime->buffer_mutex to
the read/write operations so that the concurrent hw_params or hw_free
call can no longer interfere during the operation. The mutex is
unlocked before scheduling, so we don't take it too long.
Cc: <stable@vger.kernel.org>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20220322170720.3529-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 92ee3c60ec upstream.
Currently we have neither proper check nor protection against the
concurrent calls of PCM hw_params and hw_free ioctls, which may result
in a UAF. Since the existing PCM stream lock can't be used for
protecting the whole ioctl operations, we need a new mutex to protect
those racy calls.
This patch introduced a new mutex, runtime->buffer_mutex, and applies
it to both hw_params and hw_free ioctl code paths. Along with it, the
both functions are slightly modified (the mmap_count check is moved
into the state-check block) for code simplicity.
Reported-by: Hu Jiahui <kirin.say@gmail.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20220322170720.3529-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd94df1795 upstream.
New device id for Corsair Virtuoso SE RGB Wireless that currently is not
in the mixer_map. This entry in the mixer_map is necessary in order to
label its mixer appropriately and allow userspace to pick the correct
volume controls. For instance, my own Corsair Virtuoso SE RGB Wireless
headset has this new ID and consequently, the sidetone and volume are not
working correctly without this change.
> sudo lsusb -v | grep -i corsair
Bus 007 Device 011: ID 1b1c:0a40 Corsair CORSAIR VIRTUOSO SE Wireless Gam
idVendor 0x1b1c Corsair
iManufacturer 1 Corsair
iProduct 2 CORSAIR VIRTUOSO SE Wireless Gaming Headset
Signed-off-by: Reza Jahanbakhshi <reza.jahanbakhshi@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220304212303.195949-1-reza.jahanbakhshi@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit efb6402c3c upstream.
We've got syzbot reports hitting INT_MAX overflow at vmalloc()
allocation that is called from snd_pcm_plug_alloc(). Although we
apply the restrictions to input parameters, it's based only on the
hw_params of the underlying PCM device. Since the PCM OSS layer
allocates a temporary buffer for the data conversion, the size may
become unexpectedly large when more channels or higher rates is given;
in the reported case, it went over INT_MAX, hence it hits WARN_ON().
This patch is an attempt to avoid such an overflow and an allocation
for too large buffers. First off, it adds the limit of 1MB as the
upper bound for period bytes. This must be large enough for all use
cases, and we really don't want to handle a larger temporary buffer
than this size. The size check is performed at two places, where the
original period bytes is calculated and where the plugin buffer size
is calculated.
In addition, the driver uses array_size() and array3_size() for
multiplications to catch overflows for the converted period size and
buffer bytes.
Reported-by: syzbot+72732c532ac1454eeee9@syzkaller.appspotmail.com
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/00000000000085b1b305da5a66f3@google.com
Link: https://lore.kernel.org/r/20220318082036.29699-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e8e4c8f66 upstream.
When an invalid (non existing) handle is used in a TPM command,
that uses the resource manager interface (/dev/tpmrm0) the resource
manager tries to load it from its internal cache, but fails and
the tpm_dev_transmit returns an -EINVAL error to the caller.
The existing async handler doesn't handle these error cases
currently and the condition in the poll handler never returns
mask with EPOLLIN set.
The result is that the poll call blocks and the application gets stuck
until the user_read_timer wakes it up after 120 sec.
Change the tpm_dev_async_work function to handle error conditions
returned from tpm_dev_transmit they are also reflected in the poll mask
and a correct error code could passed back to the caller.
Cc: Jarkko Sakkinen <jarkko@kernel.org>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: <linux-integrity@vger.kernel.org>
Cc: <stable@vger.kernel.org>
Cc: <linux-kernel@vger.kernel.org>
Fixes: 9e1b74a63f ("tpm: add support for nonblocking operation")
Tested-by: Jarkko Sakkinen<jarkko@kernel.org>
Signed-off-by: Tadeusz Struk <tstruk@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Cc: Tadeusz Struk <tadeusz.struk@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40cdc50987 upstream.
After the recent changes made by commit c2e3930529 ("btrfs: clear
extent buffer uptodate when we fail to write it") and its followup fix,
commit 651740a502 ("btrfs: check WRITE_ERR when trying to read an
extent buffer"), we can now end up not cleaning up space reservations of
log tree extent buffers after a transaction abort happens, as well as not
cleaning up still dirty extent buffers.
This happens because if writeback for a log tree extent buffer failed,
then we have cleared the bit EXTENT_BUFFER_UPTODATE from the extent buffer
and we have also set the bit EXTENT_BUFFER_WRITE_ERR on it. Later on,
when trying to free the log tree with free_log_tree(), which iterates
over the tree, we can end up getting an -EIO error when trying to read
a node or a leaf, since read_extent_buffer_pages() returns -EIO if an
extent buffer does not have EXTENT_BUFFER_UPTODATE set and has the
EXTENT_BUFFER_WRITE_ERR bit set. Getting that -EIO means that we return
immediately as we can not iterate over the entire tree.
In that case we never update the reserved space for an extent buffer in
the respective block group and space_info object.
When this happens we get the following traces when unmounting the fs:
[174957.284509] BTRFS: error (device dm-0) in cleanup_transaction:1913: errno=-5 IO failure
[174957.286497] BTRFS: error (device dm-0) in free_log_tree:3420: errno=-5 IO failure
[174957.399379] ------------[ cut here ]------------
[174957.402497] WARNING: CPU: 2 PID: 3206883 at fs/btrfs/block-group.c:127 btrfs_put_block_group+0x77/0xb0 [btrfs]
[174957.407523] Modules linked in: btrfs overlay dm_zero (...)
[174957.424917] CPU: 2 PID: 3206883 Comm: umount Tainted: G W 5.16.0-rc5-btrfs-next-109 #1
[174957.426689] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014
[174957.428716] RIP: 0010:btrfs_put_block_group+0x77/0xb0 [btrfs]
[174957.429717] Code: 21 48 8b bd (...)
[174957.432867] RSP: 0018:ffffb70d41cffdd0 EFLAGS: 00010206
[174957.433632] RAX: 0000000000000001 RBX: ffff8b09c3848000 RCX: ffff8b0758edd1c8
[174957.434689] RDX: 0000000000000001 RSI: ffffffffc0b467e7 RDI: ffff8b0758edd000
[174957.436068] RBP: ffff8b0758edd000 R08: 0000000000000000 R09: 0000000000000000
[174957.437114] R10: 0000000000000246 R11: 0000000000000000 R12: ffff8b09c3848148
[174957.438140] R13: ffff8b09c3848198 R14: ffff8b0758edd188 R15: dead000000000100
[174957.439317] FS: 00007f328fb82800(0000) GS:ffff8b0a2d200000(0000) knlGS:0000000000000000
[174957.440402] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[174957.441164] CR2: 00007fff13563e98 CR3: 0000000404f4e005 CR4: 0000000000370ee0
[174957.442117] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[174957.443076] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[174957.443948] Call Trace:
[174957.444264] <TASK>
[174957.444538] btrfs_free_block_groups+0x255/0x3c0 [btrfs]
[174957.445238] close_ctree+0x301/0x357 [btrfs]
[174957.445803] ? call_rcu+0x16c/0x290
[174957.446250] generic_shutdown_super+0x74/0x120
[174957.446832] kill_anon_super+0x14/0x30
[174957.447305] btrfs_kill_super+0x12/0x20 [btrfs]
[174957.447890] deactivate_locked_super+0x31/0xa0
[174957.448440] cleanup_mnt+0x147/0x1c0
[174957.448888] task_work_run+0x5c/0xa0
[174957.449336] exit_to_user_mode_prepare+0x1e5/0x1f0
[174957.449934] syscall_exit_to_user_mode+0x16/0x40
[174957.450512] do_syscall_64+0x48/0xc0
[174957.450980] entry_SYSCALL_64_after_hwframe+0x44/0xae
[174957.451605] RIP: 0033:0x7f328fdc4a97
[174957.452059] Code: 03 0c 00 f7 (...)
[174957.454320] RSP: 002b:00007fff13564ec8 EFLAGS: 00000246 ORIG_RAX: 00000000000000a6
[174957.455262] RAX: 0000000000000000 RBX: 00007f328feea264 RCX: 00007f328fdc4a97
[174957.456131] RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000560b8ae51dd0
[174957.457118] RBP: 0000560b8ae51ba0 R08: 0000000000000000 R09: 00007fff13563c40
[174957.458005] R10: 00007f328fe49fc0 R11: 0000000000000246 R12: 0000000000000000
[174957.459113] R13: 0000560b8ae51dd0 R14: 0000560b8ae51cb0 R15: 0000000000000000
[174957.460193] </TASK>
[174957.460534] irq event stamp: 0
[174957.461003] hardirqs last enabled at (0): [<0000000000000000>] 0x0
[174957.461947] hardirqs last disabled at (0): [<ffffffffb0e94214>] copy_process+0x934/0x2040
[174957.463147] softirqs last enabled at (0): [<ffffffffb0e94214>] copy_process+0x934/0x2040
[174957.465116] softirqs last disabled at (0): [<0000000000000000>] 0x0
[174957.466323] ---[ end trace bc7ee0c490bce3af ]---
[174957.467282] ------------[ cut here ]------------
[174957.468184] WARNING: CPU: 2 PID: 3206883 at fs/btrfs/block-group.c:3976 btrfs_free_block_groups+0x330/0x3c0 [btrfs]
[174957.470066] Modules linked in: btrfs overlay dm_zero (...)
[174957.483137] CPU: 2 PID: 3206883 Comm: umount Tainted: G W 5.16.0-rc5-btrfs-next-109 #1
[174957.484691] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014
[174957.486853] RIP: 0010:btrfs_free_block_groups+0x330/0x3c0 [btrfs]
[174957.488050] Code: 00 00 00 ad de (...)
[174957.491479] RSP: 0018:ffffb70d41cffde0 EFLAGS: 00010206
[174957.492520] RAX: ffff8b08d79310b0 RBX: ffff8b09c3848000 RCX: 0000000000000000
[174957.493868] RDX: 0000000000000001 RSI: fffff443055ee600 RDI: ffffffffb1131846
[174957.495183] RBP: ffff8b08d79310b0 R08: 0000000000000000 R09: 0000000000000000
[174957.496580] R10: 0000000000000001 R11: 0000000000000000 R12: ffff8b08d7931000
[174957.498027] R13: ffff8b09c38492b0 R14: dead000000000122 R15: dead000000000100
[174957.499438] FS: 00007f328fb82800(0000) GS:ffff8b0a2d200000(0000) knlGS:0000000000000000
[174957.500990] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[174957.502117] CR2: 00007fff13563e98 CR3: 0000000404f4e005 CR4: 0000000000370ee0
[174957.503513] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[174957.504864] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[174957.506167] Call Trace:
[174957.506654] <TASK>
[174957.507047] close_ctree+0x301/0x357 [btrfs]
[174957.507867] ? call_rcu+0x16c/0x290
[174957.508567] generic_shutdown_super+0x74/0x120
[174957.509447] kill_anon_super+0x14/0x30
[174957.510194] btrfs_kill_super+0x12/0x20 [btrfs]
[174957.511123] deactivate_locked_super+0x31/0xa0
[174957.511976] cleanup_mnt+0x147/0x1c0
[174957.512610] task_work_run+0x5c/0xa0
[174957.513309] exit_to_user_mode_prepare+0x1e5/0x1f0
[174957.514231] syscall_exit_to_user_mode+0x16/0x40
[174957.515069] do_syscall_64+0x48/0xc0
[174957.515718] entry_SYSCALL_64_after_hwframe+0x44/0xae
[174957.516688] RIP: 0033:0x7f328fdc4a97
[174957.517413] Code: 03 0c 00 f7 d8 (...)
[174957.521052] RSP: 002b:00007fff13564ec8 EFLAGS: 00000246 ORIG_RAX: 00000000000000a6
[174957.522514] RAX: 0000000000000000 RBX: 00007f328feea264 RCX: 00007f328fdc4a97
[174957.523950] RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000560b8ae51dd0
[174957.525375] RBP: 0000560b8ae51ba0 R08: 0000000000000000 R09: 00007fff13563c40
[174957.526763] R10: 00007f328fe49fc0 R11: 0000000000000246 R12: 0000000000000000
[174957.528058] R13: 0000560b8ae51dd0 R14: 0000560b8ae51cb0 R15: 0000000000000000
[174957.529404] </TASK>
[174957.529843] irq event stamp: 0
[174957.530256] hardirqs last enabled at (0): [<0000000000000000>] 0x0
[174957.531061] hardirqs last disabled at (0): [<ffffffffb0e94214>] copy_process+0x934/0x2040
[174957.532075] softirqs last enabled at (0): [<ffffffffb0e94214>] copy_process+0x934/0x2040
[174957.533083] softirqs last disabled at (0): [<0000000000000000>] 0x0
[174957.533865] ---[ end trace bc7ee0c490bce3b0 ]---
[174957.534452] BTRFS info (device dm-0): space_info 4 has 1070841856 free, is not full
[174957.535404] BTRFS info (device dm-0): space_info total=1073741824, used=2785280, pinned=0, reserved=49152, may_use=0, readonly=65536 zone_unusable=0
[174957.537029] BTRFS info (device dm-0): global_block_rsv: size 0 reserved 0
[174957.537859] BTRFS info (device dm-0): trans_block_rsv: size 0 reserved 0
[174957.538697] BTRFS info (device dm-0): chunk_block_rsv: size 0 reserved 0
[174957.539552] BTRFS info (device dm-0): delayed_block_rsv: size 0 reserved 0
[174957.540403] BTRFS info (device dm-0): delayed_refs_rsv: size 0 reserved 0
This also means that in case we have log tree extent buffers that are
still dirty, we can end up not cleaning them up in case we find an
extent buffer with EXTENT_BUFFER_WRITE_ERR set on it, as in that case
we have no way for iterating over the rest of the tree.
This issue is very often triggered with test cases generic/475 and
generic/648 from fstests.
The issue could almost be fixed by iterating over the io tree attached to
each log root which keeps tracks of the range of allocated extent buffers,
log_root->dirty_log_pages, however that does not work and has some
inconveniences:
1) After we sync the log, we clear the range of the extent buffers from
the io tree, so we can't find them after writeback. We could keep the
ranges in the io tree, with a separate bit to signal they represent
extent buffers already written, but that means we need to hold into
more memory until the transaction commits.
How much more memory is used depends a lot on whether we are able to
allocate contiguous extent buffers on disk (and how often) for a log
tree - if we are able to, then a single extent state record can
represent multiple extent buffers, otherwise we need multiple extent
state record structures to track each extent buffer.
In fact, my earlier approach did that:
https://lore.kernel.org/linux-btrfs/3aae7c6728257c7ce2279d6660ee2797e5e34bbd.1641300250.git.fdmanana@suse.com/
However that can cause a very significant negative impact on
performance, not only due to the extra memory usage but also because
we get a larger and deeper dirty_log_pages io tree.
We got a report that, on beefy machines at least, we can get such
performance drop with fsmark for example:
https://lore.kernel.org/linux-btrfs/20220117082426.GE32491@xsang-OptiPlex-9020/
2) We would be doing it only to deal with an unexpected and exceptional
case, which is basically failure to read an extent buffer from disk
due to IO failures. On a healthy system we don't expect transaction
aborts to happen after all;
3) Instead of relying on iterating the log tree or tracking the ranges
of extent buffers in the dirty_log_pages io tree, using the radix
tree that tracks extent buffers (fs_info->buffer_radix) to find all
log tree extent buffers is not reliable either, because after writeback
of an extent buffer it can be evicted from memory by the release page
callback of the btree inode (btree_releasepage()).
Since there's no way to be able to properly cleanup a log tree without
being able to read its extent buffers from disk and without using more
memory to track the logical ranges of the allocated extent buffers do
the following:
1) When we fail to cleanup a log tree, setup a flag that indicates that
failure;
2) Trigger writeback of all log tree extent buffers that are still dirty,
and wait for the writeback to complete. This is just to cleanup their
state, page states, page leaks, etc;
3) When unmounting the fs, ignore if the number of bytes reserved in a
block group and in a space_info is not 0 if, and only if, we failed to
cleanup a log tree. Also ignore only for metadata block groups and the
metadata space_info object.
This is far from a perfect solution, but it serves to silence test
failures such as those from generic/475 and generic/648. However having
a non-zero value for the reserved bytes counters on unmount after a
transaction abort, is not such a terrible thing and it's completely
harmless, it does not affect the filesystem integrity in any way.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3cf6a32f3f upstream.
Before this patch, the symbol end address fixup to be called, needed two
conditions being met:
if (prev->end == prev->start && prev->end != curr->start)
Where
"prev->end == prev->start" means that prev is zero-long
(and thus needs a fixup)
and
"prev->end != curr->start" means that fixup hasn't been applied yet
However, this logic is incorrect in the following situation:
*curr = {rb_node = {__rb_parent_color = 278218928,
rb_right = 0x0, rb_left = 0x0},
start = 0xc000000000062354,
end = 0xc000000000062354, namelen = 40, type = 2 '\002',
binding = 0 '\000', idle = 0 '\000', ignore = 0 '\000',
inlined = 0 '\000', arch_sym = 0 '\000', annotate2 = false,
name = 0x1159739e "kprobe_optinsn_page\t[__builtin__kprobes]"}
*prev = {rb_node = {__rb_parent_color = 278219041,
rb_right = 0x109548b0, rb_left = 0x109547c0},
start = 0xc000000000062354,
end = 0xc000000000062354, namelen = 12, type = 2 '\002',
binding = 1 '\001', idle = 0 '\000', ignore = 0 '\000',
inlined = 0 '\000', arch_sym = 0 '\000', annotate2 = false,
name = 0x1095486e "optinsn_slot"}
In this case, prev->start == prev->end == curr->start == curr->end,
thus the condition above thinks that "we need a fixup due to zero
length of prev symbol, but it has been probably done, since the
prev->end == curr->start", which is wrong.
After the patch, the execution path proceeds to arch__symbols__fixup_end
function which fixes up the size of prev symbol by adding page_size to
its end offset.
Fixes: 3b01a413c1 ("perf symbols: Improve kallsyms symbol end addr calculation")
Signed-off-by: Michael Petlan <mpetlan@redhat.com>
Cc: Athira Jajeev <atrajeev@linux.vnet.ibm.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kajol Jain <kjain@linux.ibm.com>
Cc: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: http://lore.kernel.org/lkml/20220317135536.805-1-mpetlan@redhat.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5600f69866 upstream.
Syzbot reported warning in usb_submit_urb() which is caused by wrong
endpoint type. There was a check for the number of endpoints, but not
for the type of endpoint.
Fix it by replacing old desc.bNumEndpoints check with
usb_find_common_endpoints() helper for finding endpoints
Fail log:
usb 5-1: BOGUS urb xfer, pipe 1 != type 3
WARNING: CPU: 2 PID: 48 at drivers/usb/core/urb.c:502 usb_submit_urb+0xed2/0x18a0 drivers/usb/core/urb.c:502
Modules linked in:
CPU: 2 PID: 48 Comm: kworker/2:2 Not tainted 5.17.0-rc6-syzkaller-00226-g07ebd38a0da2 #0
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.14.0-2 04/01/2014
Workqueue: usb_hub_wq hub_event
...
Call Trace:
<TASK>
aiptek_open+0xd5/0x130 drivers/input/tablet/aiptek.c:830
input_open_device+0x1bb/0x320 drivers/input/input.c:629
kbd_connect+0xfe/0x160 drivers/tty/vt/keyboard.c:1593
Fixes: 8e20cf2bce ("Input: aiptek - fix crash on detecting device without endpoints")
Reported-and-tested-by: syzbot+75cccf2b7da87fb6f84b@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/20220308194328.26220-1-paskripkin@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9b667a82c upstream.
The syzbot fuzzer reported a minor bug in the usbtmc driver:
usb 5-1: BOGUS control dir, pipe 80001e80 doesn't match bRequestType 0
WARNING: CPU: 0 PID: 3813 at drivers/usb/core/urb.c:412
usb_submit_urb+0x13a5/0x1970 drivers/usb/core/urb.c:410
Modules linked in:
CPU: 0 PID: 3813 Comm: syz-executor122 Not tainted
5.17.0-rc5-syzkaller-00306-g2293be58d6a1 #0
...
Call Trace:
<TASK>
usb_start_wait_urb+0x113/0x530 drivers/usb/core/message.c:58
usb_internal_control_msg drivers/usb/core/message.c:102 [inline]
usb_control_msg+0x2a5/0x4b0 drivers/usb/core/message.c:153
usbtmc_ioctl_request drivers/usb/class/usbtmc.c:1947 [inline]
The problem is that usbtmc_ioctl_request() uses usb_rcvctrlpipe() for
all of its transfers, whether they are in or out. It's easy to fix.
CC: <stable@vger.kernel.org>
Reported-and-tested-by: syzbot+a48e3d1a875240cab5de@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/YiEsYTPEE6lOCOA5@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 16b1941eac upstream.
The syzbot fuzzer found a use-after-free bug:
BUG: KASAN: use-after-free in dev_uevent+0x712/0x780 drivers/base/core.c:2320
Read of size 8 at addr ffff88802b934098 by task udevd/3689
CPU: 2 PID: 3689 Comm: udevd Not tainted 5.17.0-rc4-syzkaller-00229-g4f12b742eb2b #0
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.14.0-2 04/01/2014
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
print_address_description.constprop.0.cold+0x8d/0x303 mm/kasan/report.c:255
__kasan_report mm/kasan/report.c:442 [inline]
kasan_report.cold+0x83/0xdf mm/kasan/report.c:459
dev_uevent+0x712/0x780 drivers/base/core.c:2320
uevent_show+0x1b8/0x380 drivers/base/core.c:2391
dev_attr_show+0x4b/0x90 drivers/base/core.c:2094
Although the bug manifested in the driver core, the real cause was a
race with the gadget core. dev_uevent() does:
if (dev->driver)
add_uevent_var(env, "DRIVER=%s", dev->driver->name);
and between the test and the dereference of dev->driver, the gadget
core sets dev->driver to NULL.
The race wouldn't occur if the gadget core registered its devices on
a real bus, using the standard synchronization techniques of the
driver core. However, it's not necessary to make such a large change
in order to fix this bug; all we need to do is make sure that
udc->dev.driver is always NULL.
In fact, there is no reason for udc->dev.driver ever to be set to
anything, let alone to the value it currently gets: the address of the
gadget's driver. After all, a gadget driver only knows how to manage
a gadget, not how to manage a UDC.
This patch simply removes the statements in the gadget core that touch
udc->dev.driver.
Fixes: 2ccea03a8f ("usb: gadget: introduce UDC Class")
CC: <stable@vger.kernel.org>
Reported-and-tested-by: syzbot+348b571beb5eeb70a582@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/YiQgukfFFbBnwJ/9@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7f34b43e07 ]
The newly introduced TRAMP_VALIAS definition causes a build warning
with clang-14:
arch/arm64/include/asm/vectors.h:66:31: error: arithmetic on a null pointer treated as a cast from integer to pointer is a GNU extension [-Werror,-Wnull-pointer-arithmetic]
return (char *)TRAMP_VALIAS + SZ_2K * slot;
Change the addition to something clang does not complain about.
Fixes: bd09128d16 ("arm64: Add percpu vectors for EL1")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: James Morse <james.morse@arm.com>
Link: https://lore.kernel.org/r/20220316183833.1563139-1-arnd@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b04683ff8f ]
Recent commit 974578017f ("iavf: Add waiting so the port is
initialized in remove") adds a wait-loop at the beginning of
iavf_remove() to ensure that port initialization is finished
prior unregistering net device. This causes a regression
in reboot/shutdown scenario because in this case callback
iavf_shutdown() is called and this callback detaches the device,
makes it down if it is running and sets its state to __IAVF_REMOVE.
Later shutdown callback of associated PF driver (e.g. ice_shutdown)
is called. That callback calls among other things sriov_disable()
that calls indirectly iavf_remove() (see stack trace below).
As the adapter state is already __IAVF_REMOVE then the mentioned
loop is end-less and shutdown process hangs.
The patch fixes this by checking adapter's state at the beginning
of iavf_remove() and skips the rest of the function if the adapter
is already in remove state (shutdown is in progress).
Reproducer:
1. Create VF on PF driven by ice or i40e driver
2. Ensure that the VF is bound to iavf driver
3. Reboot
[52625.981294] sysrq: SysRq : Show Blocked State
[52625.988377] task:reboot state:D stack: 0 pid:17359 ppid: 1 f2
[52625.996732] Call Trace:
[52625.999187] __schedule+0x2d1/0x830
[52626.007400] schedule+0x35/0xa0
[52626.010545] schedule_hrtimeout_range_clock+0x83/0x100
[52626.020046] usleep_range+0x5b/0x80
[52626.023540] iavf_remove+0x63/0x5b0 [iavf]
[52626.027645] pci_device_remove+0x3b/0xc0
[52626.031572] device_release_driver_internal+0x103/0x1f0
[52626.036805] pci_stop_bus_device+0x72/0xa0
[52626.040904] pci_stop_and_remove_bus_device+0xe/0x20
[52626.045870] pci_iov_remove_virtfn+0xba/0x120
[52626.050232] sriov_disable+0x2f/0xe0
[52626.053813] ice_free_vfs+0x7c/0x340 [ice]
[52626.057946] ice_remove+0x220/0x240 [ice]
[52626.061967] ice_shutdown+0x16/0x50 [ice]
[52626.065987] pci_device_shutdown+0x34/0x60
[52626.070086] device_shutdown+0x165/0x1c5
[52626.074011] kernel_restart+0xe/0x30
[52626.077593] __do_sys_reboot+0x1d2/0x210
[52626.093815] do_syscall_64+0x5b/0x1a0
[52626.097483] entry_SYSCALL_64_after_hwframe+0x65/0xca
Fixes: 974578017f ("iavf: Add waiting so the port is initialized in remove")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://lore.kernel.org/r/20220317104524.2802848-1-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e0341aefc ]
ACL rules can be offloaded to VCAP IS2 either through chain 0, or, since
the blamed commit, through a chain index whose number encodes a specific
PAG (Policy Action Group) and lookup number.
The chain number is translated through ocelot_chain_to_pag() into a PAG,
and through ocelot_chain_to_lookup() into a lookup number.
The problem with the blamed commit is that the above 2 functions don't
have special treatment for chain 0. So ocelot_chain_to_pag(0) returns
filter->pag = 224, which is in fact -32, but the "pag" field is an u8.
So we end up programming the hardware with VCAP IS2 entries having a PAG
of 224. But the way in which the PAG works is that it defines a subset
of VCAP IS2 filters which should match on a packet. The default PAG is
0, and previous VCAP IS1 rules (which we offload using 'goto') can
modify it. So basically, we are installing filters with a PAG on which
no packet will ever match. This is the hardware equivalent of adding
filters to a chain which has no 'goto' to it.
Restore the previous functionality by making ACL filters offloaded to
chain 0 go to PAG 0 and lookup number 0. The choice of PAG is clearly
correct, but the choice of lookup number isn't "as before" (which was to
leave the lookup a "don't care"). However, lookup 0 should be fine,
since even though there are ACL actions (policers) which have a
requirement to be used in a specific lookup, that lookup is 0.
Fixes: 226e9cd82a ("net: mscc: ocelot: only install TCAM entries into a specific lookup and PAG")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220316192117.2568261-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f643c88c8 ]
The RXCHK block will return a partial checksum of 0 if it encounters
a problem while receiving a packet. Since a 1's complement sum can
only produce this result if no bits are set in the received data
stream it is fair to treat it as an invalid partial checksum and
not pass it up the stack.
Fixes: 8101553978 ("net: bcmgenet: use CHECKSUM_COMPLETE for NETIF_F_RXCSUM")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220317012812.1313196-1-opendmb@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 424e7834e2 ]
Commit b7a49f7305 ("bnx2x: Utilize firmware 7.13.21.0")
added request_firmware() logic in probe() which caused
load failure when firmware file is not present in initrd (below),
as access to firmware file is not feasible during probe.
Direct firmware load for bnx2x/bnx2x-e2-7.13.15.0.fw failed with error -2
Direct firmware load for bnx2x/bnx2x-e2-7.13.21.0.fw failed with error -2
This patch fixes this issue by -
1. Removing request_firmware() logic from the probe()
such that .ndo_open() handle it as it used to handle
it earlier
2. Given request_firmware() is removed from probe(), so
driver has to relax FW version comparisons a bit against
the already loaded FW version (by some other PFs of same
adapter) to allow different compatible/close enough FWs with which
multiple PFs may run with (in different environments), as the
given PF who is in probe flow has no idea now with which firmware
file version it is going to initialize the device in ndo_open()
Link: https://lore.kernel.org/all/46f2d9d9-ae7f-b332-ddeb-b59802be2bab@molgen.mpg.de/
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Fixes: b7a49f7305 ("bnx2x: Utilize firmware 7.13.21.0")
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Link: https://lore.kernel.org/r/20220316214613.6884-1-manishc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c3384050d ]
Fix a number of undefined references to drm_kms_helper.ko in
drm_dp_helper.ko:
arm-suse-linux-gnueabi-ld: drivers/gpu/drm/dp/drm_dp_mst_topology.o: in function `drm_dp_mst_duplicate_state':
drm_dp_mst_topology.c:(.text+0x2df0): undefined reference to `__drm_atomic_helper_private_obj_duplicate_state'
arm-suse-linux-gnueabi-ld: drivers/gpu/drm/dp/drm_dp_mst_topology.o: in function `drm_dp_delayed_destroy_work':
drm_dp_mst_topology.c:(.text+0x370c): undefined reference to `drm_kms_helper_hotplug_event'
arm-suse-linux-gnueabi-ld: drivers/gpu/drm/dp/drm_dp_mst_topology.o: in function `drm_dp_mst_up_req_work':
drm_dp_mst_topology.c:(.text+0x7938): undefined reference to `drm_kms_helper_hotplug_event'
arm-suse-linux-gnueabi-ld: drivers/gpu/drm/dp/drm_dp_mst_topology.o: in function `drm_dp_mst_link_probe_work':
drm_dp_mst_topology.c:(.text+0x82e0): undefined reference to `drm_kms_helper_hotplug_event'
This happens if panel-edp.ko has been configured with
DRM_PANEL_EDP=y
DRM_DP_HELPER=y
DRM_KMS_HELPER=m
which builds DP helpers into the kernel and KMS helpers sa a module.
Making DRM_PANEL_EDP select DRM_KMS_HELPER resolves this problem.
To avoid a resulting cyclic dependency with DRM_PANEL_BRIDGE, don't
make the latter depend on DRM_KMS_HELPER and fix the one DRM bridge
drivers that doesn't already select DRM_KMS_HELPER. As KMS helpers
cannot be selected directly by the user, config symbols should avoid
depending on it anyway.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Fixes: 3755d35ee1 ("drm/panel: Select DRM_DP_HELPER for DRM_PANEL_EDP")
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Tested-by: Brian Masney <bmasney@redhat.com>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Naresh Kamboju <naresh.kamboju@linaro.org>
Cc: Linux Kernel Functional Testing <lkft@linaro.org>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: dri-devel@lists.freedesktop.org
Cc: Dave Airlie <airlied@redhat.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Link: https://patchwork.freedesktop.org/patch/478296/
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 16b2dd8cdf ]
Fix double free possibility in iavf_disable_vf, as crit_lock is
freed in caller, iavf_reset_task. Add kernel-doc for iavf_disable_vf.
Remove mutex_unlock in iavf_disable_vf.
Without this patch there is double free scenario, when calling
iavf_reset_task.
Fixes: e85ff9c631 ("iavf: Fix deadlock in iavf_reset_task")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Suggested-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f74b29a4f ]
As the potential failure of the dma_map_single(),
it should be better to check it and return error
if fails.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 837d9e4940 ]
This bug resulted in only the current mode being resumed and suspended when
the PHY supported both fiber and copper modes and when the PHY only supported
copper mode the fiber mode would incorrectly be attempted to be resumed and
suspended.
Fixes: 3758be3dc1 ("Marvell phy: add functions to suspend and resume both interfaces: fiber and copper links.")
Signed-off-by: Kurt Cancemi <kurt@x64architecture.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220312201512.326047-1-kurt@x64architecture.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4db4075f92 ]
Commit 5f9c55c806 ("ipv6: check return value of ipv6_skip_exthdr")
introduced an incorrect check, which leads to all ESP packets over
either TCPv6 or UDPv6 encapsulation being dropped. In this particular
case, offset is negative, since skb->data points to the ESP header in
the following chain of headers, while skb->network_header points to
the IPv6 header:
IPv6 | ext | ... | ext | UDP | ESP | ...
That doesn't seem to be a problem, especially considering that if we
reach esp6_input_done2, we're guaranteed to have a full set of headers
available (otherwise the packet would have been dropped earlier in the
stack). However, it means that the return value will (intentionally)
be negative. We can make the test more specific, as the expected
return value of ipv6_skip_exthdr will be the (negated) size of either
a UDP header, or a TCP header with possible options.
In the future, we should probably either make ipv6_skip_exthdr
explicitly accept negative offsets (and adjust its return value for
error cases), or make ipv6_skip_exthdr only take non-negative
offsets (and audit all callers).
Fixes: 5f9c55c806 ("ipv6: check return value of ipv6_skip_exthdr")
Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e6ed96376 ]
When iterating over sockets using vsock_for_each_connected_socket, make
sure that a transport filters out sockets that don't belong to the
transport.
There actually was an issue caused by this; in a nested VM
configuration, destroying the nested VM (which often involves the
closing of /dev/vhost-vsock if there was h2g connections to the nested
VM) kills not only the h2g connections, but also all existing g2h
connections to the (outmost) host which are totally unrelated.
Tested: Executed the following steps on Cuttlefish (Android running on a
VM) [1]: (1) Enter into an `adb shell` session - to have a g2h
connection inside the VM, (2) open and then close /dev/vhost-vsock by
`exec 3< /dev/vhost-vsock && exec 3<&-`, (3) observe that the adb
session is not reset.
[1] https://android.googlesource.com/device/google/cuttlefish/
Fixes: c0cfa2d8a7 ("vsock: add multi-transports support")
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jiyong Park <jiyong@google.com>
Link: https://lore.kernel.org/r/20220311020017.1509316-1-jiyong@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46b348fd2d ]
alx_reinit has a lockdep assertion that the alx->mtx mutex must be held.
alx_reinit is called from two places: alx_reset and alx_change_mtu.
alx_reset does acquire alx->mtx before calling alx_reinit.
alx_change_mtu does not acquire this mutex, nor do its callers or any
path towards alx_change_mtu.
Acquire the mutex in alx_change_mtu.
The issue was introduced when the fine-grained locking was introduced
to the code to replace the RTNL. The same commit also introduced the
lockdep assertion.
Fixes: 4a5fe57e77 ("alx: use fine-grained locking instead of RTNL")
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Link: https://lore.kernel.org/r/20220310232707.44251-1-dossche.niels@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9feaf8b387 ]
When "dump_apple_properties" is used on the kernel boot command line,
it causes an Unknown parameter message and the string is added to init's
argument strings:
Unknown kernel command line parameters "dump_apple_properties
BOOT_IMAGE=/boot/bzImage-517rc6 efivar_ssdt=newcpu_ssdt", will be
passed to user space.
Run /sbin/init as init process
with arguments:
/sbin/init
dump_apple_properties
with environment:
HOME=/
TERM=linux
BOOT_IMAGE=/boot/bzImage-517rc6
efivar_ssdt=newcpu_ssdt
Similarly when "efivar_ssdt=somestring" is used, it is added to the
Unknown parameter message and to init's environment strings, polluting
them (see examples above).
Change the return value of the __setup functions to 1 to indicate
that the __setup options have been handled.
Fixes: 58c5475aba ("x86/efi: Retrieve and assign Apple device properties")
Fixes: 475fb4e8b2 ("efi / ACPI: load SSTDs from EFI variables")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Igor Zhbanov <i.zhbanov@omprussia.ru>
Link: lore.kernel.org/r/64644a2f-4a20-bab3-1e15-3b2cdd0defe3@omprussia.ru
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: linux-efi@vger.kernel.org
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Octavian Purdila <octavian.purdila@intel.com>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Link: https://lore.kernel.org/r/20220301041851.12459-1-rdunlap@infradead.org
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit daaca3522a upstream.
blkcg_init_queue() may add rq qos structures to request queue, previously
blk_cleanup_queue() calls rq_qos_exit() to release them, but commit
8e141f9eb8 ("block: drain file system I/O on del_gendisk")
moves rq_qos_exit() into del_gendisk(), so memory leak is caused
because queues may not have disk, such as un-present scsi luns, nvme
admin queue, ...
Fixes the issue by adding rq_qos_exit() to blk_cleanup_queue() back.
BTW, v5.18 won't need this patch any more since we move
blkcg_init_queue()/blkcg_exit_queue() into disk allocation/release
handler, and patches have been in for-5.18/block.
Cc: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org
Fixes: 8e141f9eb8 ("block: drain file system I/O on del_gendisk")
Reported-by: syzbot+b42749a851a47a0f581b@syzkaller.appspotmail.com
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20220314043018.177141-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 029c4628b2 upstream.
In our testing, a livelock task was found. Through sysrq printing, same
stack was found every time, as follows:
__swap_duplicate+0x58/0x1a0
swapcache_prepare+0x24/0x30
__read_swap_cache_async+0xac/0x220
read_swap_cache_async+0x58/0xa0
swapin_readahead+0x24c/0x628
do_swap_page+0x374/0x8a0
__handle_mm_fault+0x598/0xd60
handle_mm_fault+0x114/0x200
do_page_fault+0x148/0x4d0
do_translation_fault+0xb0/0xd4
do_mem_abort+0x50/0xb0
The reason for the livelock is that swapcache_prepare() always returns
EEXIST, indicating that SWAP_HAS_CACHE has not been cleared, so that it
cannot jump out of the loop. We suspect that the task that clears the
SWAP_HAS_CACHE flag never gets a chance to run. We try to lower the
priority of the task stuck in a livelock so that the task that clears
the SWAP_HAS_CACHE flag will run. The results show that the system
returns to normal after the priority is lowered.
In our testing, multiple real-time tasks are bound to the same core, and
the task in the livelock is the highest priority task of the core, so
the livelocked task cannot be preempted.
Although cond_resched() is used by __read_swap_cache_async, it is an
empty function in the preemptive system and cannot achieve the purpose
of releasing the CPU. A high-priority task cannot release the CPU
unless preempted by a higher-priority task. But when this task is
already the highest priority task on this core, other tasks will not be
able to be scheduled. So we think we should replace cond_resched() with
schedule_timeout_uninterruptible(1), schedule_timeout_interruptible will
call set_current_state first to set the task state, so the task will be
removed from the running queue, so as to achieve the purpose of giving
up the CPU and prevent it from running in kernel mode for too long.
(akpm: ugly hack becomes uglier. But it fixes the issue in a
backportable-to-stable fashion while we hopefully work on something
better)
Link: https://lkml.kernel.org/r/20220221111749.1928222-1-cgel.zte@gmail.com
Signed-off-by: Guo Ziliang <guo.ziliang@zte.com.cn>
Reported-by: Zeal Robot <zealci@zte.com.cn>
Reviewed-by: Ran Xiaokai <ran.xiaokai@zte.com.cn>
Reviewed-by: Jiang Xuexin <jiang.xuexin@zte.com.cn>
Reviewed-by: Yang Yang <yang.yang29@zte.com.cn>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Naoya Horiguchi <naoya.horiguchi@nec.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Roger Quadros <rogerq@kernel.org>
Cc: Ziliang Guo <guo.ziliang@zte.com.cn>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a680b1832c upstream.
The generate function in struct rng_alg expects that the destination
buffer is completely filled if the function returns 0. qcom_rng_read()
can run into a situation where the buffer is partially filled with
randomness and the remaining part of the buffer is zeroed since
qcom_rng_generate() doesn't check the return value. This issue can
be reproduced by running the following from libkcapi:
kcapi-rng -b 9000000 > OUTFILE
The generated OUTFILE will have three huge sections that contain all
zeros, and this is caused by the code where the test
'val & PRNG_STATUS_DATA_AVAIL' fails.
Let's fix this issue by ensuring that qcom_rng_read() always returns
with a full buffer if the function returns success. Let's also have
qcom_rng_generate() return the correct value.
Here's some statistics from the ent project
(https://www.fourmilab.ch/random/) that shows information about the
quality of the generated numbers:
$ ent -c qcom-random-before
Value Char Occurrences Fraction
0 606748 0.067416
1 33104 0.003678
2 33001 0.003667
...
253 � 32883 0.003654
254 � 33035 0.003671
255 � 33239 0.003693
Total: 9000000 1.000000
Entropy = 7.811590 bits per byte.
Optimum compression would reduce the size
of this 9000000 byte file by 2 percent.
Chi square distribution for 9000000 samples is 9329962.81, and
randomly would exceed this value less than 0.01 percent of the
times.
Arithmetic mean value of data bytes is 119.3731 (127.5 = random).
Monte Carlo value for Pi is 3.197293333 (error 1.77 percent).
Serial correlation coefficient is 0.159130 (totally uncorrelated =
0.0).
Without this patch, the results of the chi-square test is 0.01%, and
the numbers are certainly not random according to ent's project page.
The results improve with this patch:
$ ent -c qcom-random-after
Value Char Occurrences Fraction
0 35432 0.003937
1 35127 0.003903
2 35424 0.003936
...
253 � 35201 0.003911
254 � 34835 0.003871
255 � 35368 0.003930
Total: 9000000 1.000000
Entropy = 7.999979 bits per byte.
Optimum compression would reduce the size
of this 9000000 byte file by 0 percent.
Chi square distribution for 9000000 samples is 258.77, and randomly
would exceed this value 42.24 percent of the times.
Arithmetic mean value of data bytes is 127.5006 (127.5 = random).
Monte Carlo value for Pi is 3.141277333 (error 0.01 percent).
Serial correlation coefficient is 0.000468 (totally uncorrelated =
0.0).
This change was tested on a Nexus 5 phone (msm8974 SoC).
Signed-off-by: Brian Masney <bmasney@redhat.com>
Fixes: ceec5f5b59 ("crypto: qcom-rng - Add Qcom prng driver")
Cc: stable@vger.kernel.org # 4.19+
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-03-23 09:16:40 +01:00
86 changed files with 639 additions and 257 deletions
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.