A relatively recent commit ([1]) contained optimisation for the PIO
SPI FIFO-filling functions. The commit message includes the phrase
"[t]he blind and counted loops are always called with nonzero count".
This is technically true, but it is still possible for count to become
zero before the loop is entered - if tfr->len is zero. Moving the loop
exit condition to the end of the loop saves a few cycles, but results
in a near-infinite loop should the revised count be zero on entry.
Strangely, zero-lengthed transfers aren't filtered by the SPI framework
and, even more strangely, the Python3 spidev library is triggering them
for no obvious reason.
Avoid the problem completely by bailing out of the main transfer
function early if trf->len is zero, although there may be a case for
moving the mitigation into the framework.
See: https://github.com/raspberrypi/linux/issues/4100
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
[1] 26751de25d ("spi: bcm2835: Micro-optimise FIFO loops")
RPi4's co-processor will copy the board's bootloader[1] configuration
into memory for the OS to consume. Specifically, for the bootloader
configuration and upgrade user-space routines to query it through
nvmem's sysfs interface.
Introduce a reserved-memory area template for the co-processor to edit
before booting the system so as for Linux not to overwrite that memory
and to expose it as an nvmem device.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
[1] https://www.raspberrypi.org/documentation/hardware/raspberrypi/bcm2711_bootloader_config.md
---
Changes since v1:
- Introduce compatible string
- Change alias name to something more explicit
Firmware/co-processors might use reserved memory areas in order to pass
data stemming from an nvmem device otherwise non accessible to Linux.
For example an EEPROM memory only physically accessible to firmware, or
data only accessible early at boot time.
In order to expose this data to other drivers and user-space, the driver
models the reserved memory area as an nvmem device.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
---
Changes since v1:
- Remove reserved memory phandle indirection by directly creating a
platform device from the reserved memory DT node
- Only map memory upon reading it to avoid corruption
- Small cosmetic cleanups
Firmware/co-processors might use reserved memory areas in order to pass
data stemming from an nvmem device otherwise non accessible to Linux.
For example an EEPROM memory only physically accessible to firmware, or
data only accessible early at boot time.
Introduce the dt-bindings to nvmem's rmem.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
---
Changes since v1:
- Update schema to new driver design
Add colour denoise control to the bcm2835 driver through a new v4l2
control: V4L2_CID_USER_BCM2835_ISP_CDN.
Add the accompanying MMAL configuration structure definitions as well.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
The arm64 version of bcm2711_defconfig is intended for Pi 4, but the
Raspberry Pi OS kernel8.img built from it is also used for Pi 3. It is
therefore necessary to include some legacy drivers such as the BCM2835
thermal driver, otherwise there is no support for reading the CPU
temperature on a Pi 3 in 64-bit mode.
See: https://github.com/raspberrypi/linux/issues/4077
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
LBM base address is measured in units of pixels per cycle.
That is 4 for 2711 (hvs5) and 2 for 2708.
We are wasting 75% of lbm by indexing without the scaling.
But we were also using too high a size for the lbm resulting
in partial corruption (right hand side) of vertically
scaled images, usually at 4K or lower resolutions with more layers.
The physical RAM of LBM on 2711 is 8 * 1920 * 16 * 12-bit
(pixels are stored 12-bits per component regardless of format).
The LBM adress indexes work in units of pixels per clock,
so for 4 pixels per clock that means we have 32 * 1920 = 60K
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
This reverts commit 1c15edc0dca002c8536e9f1f5e1ec43017815018.
This revert and its neighbour are opposites. When squashing, delete
the original commits as well.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
It turns out the used CAN SPI chip is not a good way to identify the version of
the CAN HAT.
There are two different board layouts of the Seeed Studio CAN BUS FD HAT. The
v1 board doesn't have a battery holder, while the v2 board has. Update the
overlay README accordinly.
Link: https://github.com/Seeed-Studio/seeed-linux-dtoverlays/issues/13
Cc: Patrick Menschel <menschel.p@posteo.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Update those overlays that use the regulator framework to use the
new cam1_reg node to control the camera shutdown line, and remove
the firmware workaround nodes.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The current firmware fixup of camera sensor overlays is not
particularly nice, and it stops you being able to load them
dynamically.
It's also incompatible with creating a simple DT that can be
loaded for both CAM1 and CAM0 on a CM as they would both
try to claim the one GPIO.
Almost all sensors have a hook of some form for a regulator, so
it's relatively straightforward to convert them all to use a
fixed regulator with GPIO control.
Add a fixed regulator node for each platform with the GPIO
correctly configured for the camera shutdown line. (The LED line
is ignored).
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
This patch adds the overlay for the Seeed Studio CAN BUS FD HAT v1 with two CAN
FD Channels (based on mcp2517fd).
https://www.seeedstudio.com/2-Channel-CAN-BUS-FD-Shield-for-Raspberry-Pi-p-4072.html
The overlay was generated by:
ovmerge -c spi1-1cs-overlay.dts,cs0_pin=18,cs0_spidev=false \
mcp251xfd-overlay.dts,spi0-0,interrupt=25 \
mcp251xfd-overlay.dts,spi1-0,interrupt=24
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There are several versions of the Seeed Studio CAN BUS FD HAT. This is the
second version, based on the mcp2518fd, so give it a -v2 postfix.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
To comply with the intended usage of the V4L2 selection target when
used to retrieve a sensor image properties, adjust the rectangles
returned by the ov5647 driver.
The top/left crop coordinates of the TGT_CROP rectangle were set to
(0, 0) instead of (16, 16) which is the offset from the larger physical
pixel array rectangle. This was also a mismatch with the default values
crop rectangle value, so this is corrected. Found with v4l2-compliance.
While at it, add V4L2_SEL_TGT_CROP_BOUNDS support: CROP_DEFAULT and
CROP_BOUNDS have the same size as the non-active pixels are not readable
using the selection API. Found with v4l2-compliance.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Use (reserved) bits 24 and 25 of the dreq value
(the second cell of the DT DMA descriptor) to request
that wide source reads or wide dest writes are required
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
When logging that the firmware has provided more supported formats
than we had allocated storage for, log the number allocated and
returned.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Now that the firmware supports the unpacked (16bpp) variants
of the MIPI raw formats, add the mappings.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
When logging that the firmware has provided more supported formats
than we had allocated storage for, log the number allocated and
returned.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Now that the firmware supports the unpacked (16bpp) variants
of the MIPI raw formats, add the mappings.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Support has been added for the unpacked (16bpp) versions of
the MIPI raw 10, 12, and 14 formats, so add the 4CCs for them.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
For some reason lost in history function vchiq_mmal_init used
a static variable for storing the vchiq_instance.
This value is retrieved from vchiq per instance, so worked fine
until you try to call vchiq_mmal_init multiple times concurrently
when things then go wrong. This seemed to happen quite frequently
if using the cutdown firmware (no MMAL or VCSM services running)
as the vchiq_connect then failed, and one or other vchiq_shutdown
was working on an invalid handle.
Remove the static so that each caller gets a unique vchiq_instance.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The recent change to the bulk transfer compat function missed the fact
the relevant ioctl command is VCHIQ_IOC_QUEUE_BULK_TRANSMIT32, not
VCHIQ_IOC_QUEUE_BULK_TRANSMIT, as any attempt to send a bulk block
to the VPU would have shown.
Fixes: a4367cd2b2 ("staging: vchiq: convert compat bulk transfer")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
error logs:
drivers/staging/vc04_services/vc-sm-cma/Kconfig:1:error: recursive dependency detected!
drivers/staging/vc04_services/vc-sm-cma/Kconfig:1: symbol BCM_VC_SM_CMA is selected by BCM2835_VCHIQ_MMAL
drivers/staging/vc04_services/vchiq-mmal/Kconfig:1: symbol BCM2835_VCHIQ_MMAL depends on BCM2835_VCHIQ
drivers/staging/vc04_services/Kconfig:14: symbol BCM2835_VCHIQ is selected by BCM_VC_SM_CMA
For a resolution refer to Documentation/kbuild/kconfig-language.rst
subsection "Kconfig recursive dependency limitations"
Tested-by: make ARCH=arm64 bcm2711_defconfig
Test platform: fedora 33
Branch: rpi-5.10.y
This patch adds the overlay for the Seeed Studio CAN BUS FD HAT
with two CAN FD Channels and an RTC.
https://www.seeedstudio.com/CAN-BUS-FD-HAT-for-Raspberry-Pi-p-4742.html
The overlay was generated by
ovmerge -c mcp251xfd-overlay.dts,spi0-0,interrupt=25 \
mcp251xfd-overlay.dts,spi0-1,interrupt=24 \
i2c-rtc-overlay.dts,pcf85063
Also, add description on how to generate overlays
Signed-off-by: Patrick Menschel <menschel.p@posteo.de>
The addition of the local 'userdata' pointer to
vchiq_irq_queue_bulk_tx_rx omitted the case where neither BLOCKING nor
WAITING modes are used, in which case the value provided by the
caller is replaced with a NULL.
Fixes: 4184da4f31 ("staging: vchiq: fix __user annotations")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The BCM2711 supports higher bpc count than just 8, so let's support it in
our driver.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Unlike the previous generations, the HSM clock limitation is way above
what we can reach without scrambling, so let's move the maximum
frequency we support to the maximum clock frequency without scrambling.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The PHY initialisation parameters are not based on the pixel clock but
the TMDS clock rate which can be the pixel clock in the standard case,
but could be adjusted based on some parameters like the bits per color.
Since the TMDS clock rate is stored in our custom connector state
already, let's reuse it from there instead of computing it again.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The pixel rate is for now quite simple to compute, but with more features
(30 and 36 bits output, YUV output, etc.) will depend on a bunch of
connectors properties.
Let's store the rate we have to run the pixel clock at in our custom
connector state, and compute it in atomic_check.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
When run with a higher bpc than 8, the clock of the HDMI controller needs
to be adjusted. Let's create a connector state that will be used at
atomic_check and atomic_enable to compute and store the clock rate
associated to the state.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm_atomic_helper_connector_reset uses kmalloc which, from an API
standpoint, can fail, and thus setting connector->state to NULL.
However, our reset hook then calls drm_atomic_helper_connector_tv_reset
that will access connector->state without checking if it's a valid
pointer or not.
Make sure we don't end up accessing a NULL pointer.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Suggested-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Commit 63495f6b4a ("drm/vc4: hdmi: Make sure our clock rate is within
limits") was intended to compute the pixel rate to make sure we remain
within the boundaries of what the hardware can provide.
However, unlike what mode_valid was checking for, we forgot to take
into account the clock doubling flag that can be set for modes. Let's
honor that flag if it's there.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reported-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Fixes: 63495f6b4a ("drm/vc4: hdmi: Make sure our clock rate is within limits")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
We'll need to access the connector state in our encoder setup, so let's
just pass the whole DRM state to our private encoder hooks.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Since the CRTC setup in vc4 is split between the PixelValves/TXP and the
HVS, only the PV/TXP atomic hooks were updated in the previous commits, but
it makes sense to update the HVS ones too.
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
It appears that the V4L2 M2M framework requires the driver to manually
call vb2_clear_last_buffer_dequeued on the CAPTURE queue during a
V4L2_DEC_CMD_START.
Add such a call.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Control V4L2_CID_MPEG_VIDEO_HEADER_MODE controls whether the encoder
is meant to emit the header bytes as a separate packet or with the
first encoded frame.
Add support for it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
To comply with the intended usage of the V4L2 selection target when
used to retrieve a sensor image properties, adjust the rectangles
returned by the imx477 driver.
The top/left crop coordinates of the TGT_CROP rectangle were set to
(0, 0) instead of (8, 16) which is the offset from the larger physical
pixel array rectangle. This was also a mismatch with the default values
crop rectangle value, so this is corrected. Found with v4l2-compliance.
While at it, add V4L2_SEL_TGT_CROP_BOUNDS support: CROP_DEFAULT and
CROP_BOUNDS have the same size as the non-active pixels are not readable
using the selection API. Found with v4l2-compliance.
This commit mirrors 543790f777 done for
the imx219 sensor.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
The overlays for the ads1015 and ads1115 I2C ADCs omitted the addresses
in the main device node names. As well as breaking the conventions for
I2C devices, this prevents the firmware from renaming them when the
"reg" property is modified, which in turn stops the overlays from being
instantiated multiple times.
See: https://www.raspberrypi.org/forums/viewtopic.php?f=107&t=294465
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Eric's view was that there was no point in having zpos
support on vc4 as all the planes had the same functionality.
Can be later squashed into (and fixes):
drm/vc4: Add firmware-kms mode
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
The mpu6050 starts up at address 0x68 by default, but can be set to
0x69 if the ADO pin is pulled high. Give the overlay an addr parameter
to allow devices at the alternate address to be used.
See: https://github.com/Hexxeh/rpi-firmware/issues/252
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
lan78xx_link_reset explicitly clears the MAC's view of the PHY's IRQ
status. In doing so it potentially leaves the PHY with a pending
interrupt that will never be acknowledged, at which point no further
interrupts will be generated.
Avoid the problem by acknowledging any pending PHY interrupt after
clearing the MAC's status bit.
See: https://github.com/raspberrypi/linux/issues/2937
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The firmware by default tries to ensure that decoded frame
timestamps always increment. This is counter to the V4L2 API
which wants exactly the OUTPUT queue timestamps passed to the
CAPTURE queue buffers.
Disable the firmware option.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Add support for the PCF85063 and PCF85063A RTC devices to the
i2c-rtc overlay.
Also enable the device to be used on i2c0 (i2c_vc) on GPIOs 0&1 (use
parameter "i2c0") and GPIOs 44 & 45 (use parameter "i2c_csi_dsi").
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Although the BRCMSTB PCIe interface doesn't technically support the
MSI-X spec, in practise it seems to work provided no more than 32
MSI-Xs are required. Add the required flag to the driver to allow
experimentation with devices that demand MSI-X support.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Commit 65e08c4650 failed to clear the
clock state when the device stopped streaming. Fix this, as it might
again cause the same problems when doing an unprepare.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
clk_disable_unprepare() is called unconditionally in stop_streaming().
This is incorrect in the cases where start_streaming() fails, and
unprepares all clocks as part of the failure cleanup. To avoid this,
ensure that clk_disable_unprepare() is only called in stop_streaming()
if the clocks are in a prepared state.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
On a failure in start_streaming(), the error code would not propagate to
the calling function on all conditions. This would cause the userland
caller to not know of the failure.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
The DSI1_PHY_AFEC0_PD_DLANE1 and DSI1_PHY_AFEC0_PD_DLANE3 register
definitions were swapped, so trying to use more than a single data
lane failed as lane 1 would get powered down.
(In theory a 4 lane device would work as all lanes would remain
powered).
Correct the definitions.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The hdmi reset got moved to a later point in
"drm/vc4: hdmi: Add reset callback"
which now occurs after vc4_hdmi_cec_init
and so tramples the setup of registers like
HDMI_CEC_CNTRL_1
This only affects pi0-3 as on pi4 the cec
resgisters are in a separate block
Fixes: ed9a1f6eb4
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
BCM2711 DSI1 doesn't have the issue with the ARM not being
able to write to the registers, therefore remove the DMA
workaround for that compatible string.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
DSI1 on BCM2711 doesn't require the DMA workaround that is used
on BCM2835/6/7, therefore it needs a new compatible string.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
DSI0 was partially supported, but didn't register with the main
driver, and the code was inconsistent as to whether it checked
port == 0 or port == 1.
Add compatible string and other support to make it consistent.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Breaks out common register set and adds the different registers
for 1280x720 (cropped) and 640x480 (skipped) modes
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
CONFIG_BRIDGE_NETFILTER=m used to be the default when CONFIG_NETFILTER
was enabled, but that was removed in 5.9. The way that defconfigs work
caused this wanted setting to be lost in rpi-5.9.y and rpi-5.10.y -
restore it now.
See: https://github.com/Hexxeh/rpi-firmware/issues/248
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The CAN_ISOTP setting was in the wrong position, and it's better for
bisecting and reverting if this doesn't get rolled into the next
config-changing commit.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
In switching to the hardware I2C controller there is an issue
where we seem to not get back the correct state from the Pi
touchscreen.
Insert a delay before polling to avoid this condition.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
We now have the hardware I2C controller pinmuxed to the drive the
display I2C, but this controller does not support clock stretching.
The Atmel micro-controller in the panel requires clock stretching
to allow it to prepare any data to be read.
Split the rpi_touchscreen_i2c_read into two independent transactions with
a delay between them for the Atmel to prepare the data.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
This touchscreen controller is used by the 7" DSI panel, and
this overlay configures it for when it is NOT being polled by
the firmware.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Not all systems have the interrupt line wired up, so switch to
polling the touchscreen off a timer if no interrupt line is
configured.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Using a hdmi analyser the bytes in packet ram
registers beyond the length were visible in the
infoframes and it flagged the checksum as invalid.
Zeroing unused words of packet RAM avoids this
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
[1] replaced a single reset function with a pointer to one of two
implementations, but also removed the call asserting the reset
at the start of brcm_pcie_setup. Doing so breaks Raspberry Pis with
VL805 XHCI controllers lacking dedicated SPI EEPROMs, which have been
used for USB booting but then need to be reset so that the kernel
can reconfigure them. The lack of a reset causes the firmware's loading
of the EEPROM image to RAM to fail, breaking USB for the kernel.
See: https://www.raspberrypi.org/forums/viewtopic.php?p=1758157#p1758157
Fixes: 04356ac307 ("PCI: brcmstb: Add bcm7278 PERST# support")
[1] 04356ac307 ("PCI: brcmstb: Add bcm7278 PERST# support")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
* Add mcp251xfd driver module to the RPi kernel builds.
* Add isotp can protocol module to the RPi kernel builds.
Signed-off-by: Patrick Menschel <menschel.p@posteo.de>
The enable_headphones parameter of the snd_bcm2835 module is forced
to 1 if enable_compat_alsa is 0, so setting them both on the kernel
command line is pointless (and, in the case of Pi 400 and Pi Zeroes,
confusing).
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The sdtweak overlay has been superseded by the board-specific
sd_* parameters such as sd_poll_once, sd_overclock etc.
For example, replace:
dtoverlay=sdtweak,poll_once
with:
dtparam=sd_poll_once
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The last nibble is a revision ID, and the 54213pe is a later rev
than the 54210e. Running the 54210e setup code on a 54213pe results
in a broken RGMII interface.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Define a new mailbox (SET_REBOOT_FLAGS) which may be used to
pass optional flags to the Raspberry Pi firmware that changes
the behaviour of the bootloader and firmware during a reboot.
Currently this just defines the 'tryboot' flag which causes
the firmware to load tryboot.txt instead config.txt. This
alternate configuration file can be used to specify the
path of an alternate firmware and kernels allowing a fallback
mechanism to be implemented for OS upgrades.
Delete a large amount of unused declaration from "usb.h", some of which
were causing build warnings, and get the module building cleanly.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
RASPBERRYPI_FIRMWARE was missing from the arm64 bcm2711_defconfig.
bcmrpi3_defconfig was also missing a few options. Add the misssing
settings and regenerate all the Pi defconfigs.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Attempts to connect external GPUs to Compute Module 4's PCIe bus have
highlighted that the existing "outbound window" - the fraction of the
PCI address base that is appears in the host's memory map - is
restrictively small. Expand the window to a full 1GB.
See: https://www.raspberrypi.org/forums/viewtopic.php?f=98&t=288902
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Add a property to allow the headphone output to be disabled. Use an
integer property rather than a boolean so that an overlay can clear it.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The VL805 controller can't cope with the TR Dequeue Pointer for an endpoint
being set to a Link TRB. The hardware-maintained endpoint context ends up
stuck at the address of the Link TRB, leading to erroneous ring expansion
events whenever the enqueue pointer wraps to the dequeue position.
If the search for the end of the current TD and ring cycle state lands on
a Link TRB, move to the next segment.
See: https://github.com/raspberrypi/linux/issues/3919
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
With vc4-drv node not being under /soc on Pi4, we need to
adopt the correct DMA parameters from a suitable sub-component.
Add "brcm,bcm2711-hvs" to that list of components.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The upstream driver is checking the link frequency parameter, and
the overlay had the wrong value.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Composite gets enabled automatically if HDMI isn't detected,
which can cause some grief in X should it be not connected
and touchscreens are in use.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The upstream bcm2837.dtsi uses cortex-a53-pmu, so we can do the same
but with a fallback to the cortex-a7-pmu which is supported by the
32-bit kernel.
Now that we're using the natural fallback mechanism of compatible
strings, the RPI364 macro no longer serves any purpose - remove it.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The vc5 HDMI registers hadn't been added into the debugfs
register sets, therefore weren't dumped on request.
Add them in.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The order of precedence should be:
- hotplug GPIO being defined
- DDC probe
- hotplug register
In particular the hotplug register is not valid if a GPIO is defined
(eg on Pi0-3), but was being checked.
Fixes "943f078 vc4: cec: Restore cec physical address on reconnect"
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The gpio-fsm driver implements simple state machines that allow GPIOs
to be controlled in response to inputs from other GPIOs - real and
soft/virtual - and time delays. It can:
+ create dummy GPIOs for drivers that demand them,
+ drive multiple GPIOs from a single input, with optional delays,
+ add a debounce circuit to an input,
+ drive pattern sequences onto LEDs
etc.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Overlays are unable to remove properties in the base DTB, but they
can overwrite them. Allow a present but empty 'dmas' property
to also disable the HDMI audio interface.
See: https://github.com/raspberrypi/linux/issues/2489
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Driver for the BCM2835 ISP hardware block. This driver uses the MMAL
component to program the ISP hardware through the VC firmware.
The ISP component can produce two video stream outputs, and Bayer
image statistics. This can't be encompassed in a simple V4L2
M2M device, so create a new device that registers 4 video nodes.
This patch squashes all the development patches from the earlier
rpi-5.4.y branch into one
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
This file defines the userland interface to the bcm2835-isp driver
that will follow in a separate commit.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
If CONFIG_DMA_BCM2708 isn't enabled there's no need to mask out
one of the already scarce DMA channels.
Signed-off-by: Matthias Reichl <hias@horus.com>
This adds a V4L2 memory to memory device that wraps the MMAL
video decode and video_encode components for H264 and MJPEG encode
and decode, MPEG4, H263, and VP8 decode (and MPEG2 decode
if the appropriate licence has been purchased).
This patch squashes all the work done in developing the driver
on the Raspberry Pi rpi-5.4.y kernel branch.
Thanks to Kieran Bingham, Aman Gupta, Chen-Yu Tsai, and
Marek Behún for their contributions. Please refer to the
rpi-5.4.y branch for the full history.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
With the vc-sm-cma driver we can support zero copy of buffers between
the kernel and VPU. Add this support to mmal-vchiq.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Add Broadcom VideoCore Shared Memory support.
This new driver allows contiguous memory blocks to be imported
into the VideoCore VPU memory map, and manages the lifetime of
those objects, only releasing the source dmabuf once the VPU has
confirmed it has finished with it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
If the RBUF logic is not reset when the kernel starts then there
may be some data left over from any network boot loader. If the
64-byte packet headers are enabled then this can be fatal.
Extend bcmgenet_dma_disable to do perform the reset, but not when
called from bcmgenet_resume in order to preserve a wake packet.
N.B. This different handling of resume is just based on a hunch -
why else wouldn't one reset the RBUF as well as the TBUF? If this
isn't the case then it's easy to change the patch to make the RBUF
reset unconditional.
See: https://github.com/raspberrypi/linux/issues/3850
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Increase the delay before entering the lower power state to 2 seconds
(the maximum allowed) in order to reduce the packet latencies,
particularly for inbound packets.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Display variants are intended as a replacement for the now-deleted
fbtft_device drivers. Drivers can register additional compatible
strings with a custom callback that can make the required changes
to the fbtft_display structure.
Start the ball rolling by adding adafruit18, adafruit18_green and
sainsmart18 displays.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Since the unicam driver was modified to write to a dummy buffer when no
user-supplied buffer is available, it can now write to and return a
buffer even when there's only a single one. Enable this by changing the
min_buffers_needed in the vb2_queue; it will be useful for enabling
still captures without allocating more memory than absolutely necessary.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
The change to retrieve the pixel format always on g_fmt didn't
check whether the native or unpacked version of the format
had been requested, and always returned the packed one.
Correct this so that the packing setting is retained whereever
possible.
Fixes "9d59e89 media: bcm2835-unicam: Re-fetch mbus code from subdev
on a g_fmt call"
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
From when bringing up the driver, there was a check in the isr
to ignore interrupts (claiming them handled) should the driver
not be streaming.
The VPU now will not register a camera driver if it finds a
CSI2 node enabled in device tree, therefore this flawed check is
redundant.
https://github.com/raspberrypi/linux/issues/3602
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Parse device properties and register controls for them using the V4L2
fwnode properties helpers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Use V4L2_CID_EXPOSURE_AUTO_PRIORITY to control if the driver should
automatically adjust the sensor frame length based on exposure time,
allowing variable frame rates and longer exposures.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Adds a driver for the 12MPix Sony IMX477 CSI2 sensor.
Whilst the sensor supports 2 or 4 CSI2 data lanes, this driver
currently only supports 2 lanes.
The following Bayer modes are currently available:
4056x3040 12-bit @ 10fps
2028x1520 12-bit (binned) @ 40fps
2028x1050 12-bit (cropped/binned) @ 50fps
1012x760 10-bit (scaled) @ 120 fps
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Under FKMS, the firmware (via FKMS) also requires the VideoCore cache
aliases for image planes, as defined by the dma-ranges under /soc.
Add rpi-firmware-kms to the list of acceptable nodes to look for
to copy dma config from.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
This is a squash of all firmware-kms related patches from previous
branches, up to and including
"drm/vc4: Set the possible crtcs mask correctly for planes with FKMS"
plus a couple of minor fixups for the 5.9 branch.
Please refer to earlier branches for full history.
This patch includes work by Eric Anholt, James Hughes, Phil Elwell,
Dave Stevenson, Dom Cobley, and Jonathon Bell.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm/vc4: Fixup firmware-kms after "drm/atomic: Pass the full state to CRTC atomic enable/disable"
Prototype for those calls changed, so amend fkms (which isn't
upstream) to match.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The BT601/BT709 color encoding and limited vs full
range properties were not being exposed, defaulting
always to BT601 limited range.
Expose the parameters and set the registers appropriately.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
This currently doesn't handle non-zero source rectangles correctly,
but add support for DRM_FORMAT_P030 with DRM_FORMAT_MOD_BROADCOM_SAND128
modifier to planes when running on HVS5.
WIP still for source cropping SAND/P030 formats
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Currently we call cec_phys_addr_invalidate on a hotplug deassert.
That may be due to a TV power cycling, or an AVR being switched
on (and switching edid). This makes CEC unusable.
Set it back up again on the hotplug assert.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
This follows logic in hdmi-codec.c to use speaker layout
from ELD to choose a suitable speaker mapping based on
number of channels requested and signal that in audio
infoframe and report this back to userspace.
This allows apps like speaker-test and kodi to get the
output to the right speakers.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Without this bit set, HDMI_MAI_FORMAT doesn't pick up
the format and samplerate from DVP_CFG_MAI0_FMT and you
can't get HDMI_HDMI_13_AUDIO_STATUS_1 to indicate HBR mode
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
This was a workaround for bugs in hardware on earlier Pi models
and wasn't totally successful.
It makes audio quality worse on a Pi4 at the higher sample rates
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Configuring HDMI audio registers in prepare allows us to take
IEC958 bits into account which are set by the alsa hook after
the hw_params call.
Signed-off-by: Matthias Reichl <hias@horus.com>
Although vc4 get an IEC958 formatted stream passed in from userspace
the driver needs the info from the channel status bits to properly
set up the hardware, eg for HBR passthrough.
Add iec958 controls so the channel status bits can be passed in
from userspace.
Signed-off-by: Matthias Reichl <hias@horus.com>
The hardware uses this for generating the right audio
data island packets when using formats other than PCM
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Symptom is random switching of speakers when using multichannel.
Repeatedly running speakertest -c8 occasionally starts with
channels jumbled. This is fixed with HD_CTL_WHOLSMP.
The other bit looks beneficial and apears harmless in testing so
I'd suggest adding it too.
Documentation says: HD_CTL_WHILSMP_SET
Wait for whole sample. When this bit is set MAI transmit will start
only when there is at least one whole sample available in the fifo.
Documentation says: HD_CTL_CHALIGN_SET
Channel Align When Overflow. This bit is used to realign the audio
channels in case of an overflow.
If this bit is set, after the detection of an overflow, equal
amount of dummy words to the missing words will be written to fifo,
filling up the broken sample and maintaining alignment.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
vc4_drv isn't necessarily under the /soc node in DT as it is a
virtual device, but it is the one that does the allocations.
The DMA addresses are consumed by primarily the HVS or V3D, and
those require VideoCore cache alias address mapping, and so will be
under /soc.
During probe find the a suitable device node for HVS or V3D,
and adopt the DMA configuration of that node.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
During a bulk transfer we request a DMA allocation to hold the
scatter-gather list. Most of the time, this allocation is small
(<< PAGE_SIZE), however it can be requested at a high enough frequency
to cause fragmentation and/or stress the CMA allocator (think time
spent in compaction here, or during allocations elsewhere).
Implement a pool to serve up small DMA allocations, falling back
to a coherent allocation if the request is greater than
VCHIQ_DMA_POOL_SIZE.
Signed-off-by: Oliver Gjoneski <ogjoneski@gmail.com>
The sensor supports 8 bit mode as well as 10bit, so add the
relevant code to allow selection of this.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Fix commit "media: tc358743: Return an appropriate colorspace from
tc358743_set_fmt" to ensure that the format passed in to set_fmt
is checked to be valid, and reset to the current format if not.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Pi 0&1 pass all ARM accesses through the VPU L2 cache, therefore
the dma-ranges property sets the cache alias bits to other
than the direct alias, hence this WARN was firing.
It was overprotective coding, so assume that everything is OK
with the dma-ranges, and remove the WARN.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
MEDIA_CONTROLLER_REQUEST_API is a hidden option. If rpivid depends on it,
the user would need to first enable another driver that selects
MEDIA_CONTROLLER_REQUEST_API, and only then rpivid would become available.
By selecting it instead of depending on it, it becomes possible to enable
rpivid without having to enable other potentially unnecessary drivers.
Signed-off-by: Hristo Venev <hristo@venev.name>
In an attempt to prevent the problem of CPUn not starting, explicitly
misalign the scratch space used to save registers acros the cache
invalidation.
Notes:
At this stage in the boot process the core is running with its cache
disabled. Before enabling the cache its contents must be explicitly
invalidated, a process that requires quite a few registers that the
caller must preserve. Evidence suggests that something is writing a
block of zeroes over that space at a time when all other cores should
be idle, possibly some kind of write-combiner, and the misalignment is
designed to disrupt any write-coalescing.
In truth, I don't understand why this patch works, and when the failure
is so random it is hard to be certain that this isn't just rolling the
dice again. One interesting test would be to change the "addeq r12, #4"s
to "addeq r12, #0"s determine see if the offset itself is significant or
just the additional code.
See: https://github.com/Hexxeh/rpi-firmware/issues/232
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Although it is no longer necessary for vchiq's children to have a
different DMA configuration to the parent, they do still need to
explicitly to have their DMA configuration set - to be that of the
parent.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The actpwr trigger is a meta trigger that cycles between an inverted
mmc0 and default-on. It is written in a way that could fairly easily
be generalised to support alternative sets of source triggers.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Parse device properties and register controls for them using the V4L2
fwnode properties helpers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
When streaming with Unicam, the VPU must have a clock frequency of at
least 250Mhz. Otherwise, the input fifos could overrun, causing
image corruption.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
[g|s]_selection pass in a buffer type that needs to be validated
before passing on to the sensor subdev.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
v4l2-compliance throws a failure if the device doesn't advertise
V4L2_CAP_READWRITE but allows read or write operations.
We do support read, so reinstate the flag.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The colorspace fields were left untouched in imx290_set_fmt
which lead to a v4l2-compliance failure.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Userspace needs to know the cropping arrangements for each mode,
so expose this through g_selection.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
__v4l2_ctrl_modify_range only updates the current value should
it be invalid within the new range. That can leave modes producing
odd frame rates.
Explicitly update the HBLANK and VBLANK values so that on mode
change we revert to the default frame rate for the mode.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Vision Components have made an OV9281 module which blocks reading
back the majority of registers to comply with NDAs, and in doing
so doesn't allow auto-increment register reading as used when
reading the chip ID.
Use two reads and manually combine the results.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The Rockchip driver was based on a 4.4 kernel, and had several custom
Rockchip parts.
Update to 5.4 kernel APIs, with the relevant controls required by
libcamera, and remove custom Rockchip parts.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Adds the ov9281 parts of the Rockchip patch adding enum_frame_interval to
a large number of drivers.
Change-Id: I03344cd6cf278dd7c18fce8e97479089ef185a5c
Signed-off-by: Zefa Chen <zefa.chen@rock-chips.com>
Takes the ov9281 part only from the Rockchip's patch.
Change-Id: I30e833baf2c1bb07d6d87ddb3b00759ab45a90e4
Signed-off-by: Zefa Chen <zefa.chen@rock-chips.com>
Use bit 27 of the dreq value (the second cell of the DT DMA descriptor)
to request that the WAIT_RESP bit is not set.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Now that the 14bit non-packed Bayer formats are defined, add them
into the supported formats lookup table.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Now that V4L2_PIX_FMT_Y14 and V4L2_PIX_FMT_Y14P are defined,
allow passing 14bit mono data through the peripheral.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Now that V4L2_PIX_FMT_Y12P is defined, allow passing raw 12bit
mono packed data through the peripheral.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
imx290_set_hmax was using two independent writes to set up hmax,
when all other multi-register writes were using imx290_write_buffered_reg
which claims the group hold first.
Switch imx290_set_hmax to using imx290_write_buffered_reg too.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The IMX290 module is available as either mono or colour (Bayer).
Update the driver so that it can advertise the correct mono
formats instead of the colour ones.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The IMX290 module is available as either monochrome or colour and
the variant is not detectable at runtime.
Add a new compatible string for the monochrome version.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The sensor supports horizontal and vertical flips, so support them
through V4L2_CID_HFLIP and V4L2_CID_VFLIP.
This sensor does NOT change the Bayer order when changing the
direction of readout, therefore no special handling is required for
that.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Adds support for V4L2_CID_EXPOSURE so that userspace can control
the sensor exposure time.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
In order to calculate framerate and durations userspace needs
the vertical blanking information. This can be configurable,
and indeed the datasheet lists different values for VBLANK for
the 1080p and 720p modes.
Add the new control, and adopt the datasheet values for each mode.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Userspace needs to know HBLANK if it is to work out exposure times
and frame rates, therefore convert it to map onto V4L2_CID_HBLANK
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The datasheet lists the gain as being 0.0 to 72.0dB in 0.3dB steps, which
makes 238 steps total.
Correct the 0-72 range defined in the driver.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The existing driver only supported a clock of 37.125MHz, but the
sensor also supports 74.25MHz.
Add the relevant register modifications to support this alternate
clock frequency.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Commit d46cfdc86c upstream.
With the current driver 'media-ctl -p' issued right after the imx290 driver
is loaded prints:
pad0: Source
[fmt:unknown/0x0]
The format value of zero is due to the current_format field of the imx290
struct not being initialized yet.
As imx290_entity_init_cfg() calls imx290_set_fmt(), the current_mode field
is also initialized, so the line which set current_mode to a default value
in driver's probe() function is no longer needed.
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Older gcc versions object to = { 0 } initialisation if the first
elemtn in the structure is a substructure.
Use = { } to avoid this compiler warning.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Use the get_mbus_config pad subdev call to allow a source to use
fewer than the number of CSI2 lanes defined in device tree.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Add a driver for the Unicam camera receiver block on BCM283x processors.
Compared to the bcm2835-camera driver present in staging, this driver
handles the Unicam block only (CSI-2 receiver), and doesn't depend on
the VC4 firmware running on the VPU.
The commit is made up of a series of changes cherry-picked from the
rpi-5.4.y branch of https://github.com/raspberrypi/linux/ with
additional enhancements, forward-ported to the mainline kernel.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reported-by: kbuild test robot <lkp@intel.com>
Commit 8353fe6f1e ("Revert "staging: bcm2835-audio: Drop DT
dependency"") reverts the upstream change and makes bcm2835-audio use
device tree again, however, it also removes the MODULE_ALIAS for the
platform device. This MODULE_ALIAS is needed, because VCHIQ registers
bcm2835-audio as a child platform device since commit 25c7597af2
("staging: vchiq_arm: Register a platform device for audio"), and this
mechanism is adopted also in the downstream kernel.
This commit puts back that MODULE_ALIAS to make bcm2835-audio
autoprobing work again. The rest of VCHIQ children have their
MODULE_ALIASes in place.
Fixes: 8353fe6f1e ("Revert "staging: bcm2835-audio: Drop DT dependency"")
Signed-off-by: Maxim Mikityanskiy <maxtram95@gmail.com>
When closing the video device, the irs1125 is put in power down state.
To keep V4L2 ctrls and the HW in sync, v4l2_ctrl_handler_setup is
called after power up.
The compound ctrl IRS1125_CID_MOD_PLL however has a default value
of all zeros, which puts the imager into a non responding state.
Thus, this ctrl is not written by the driver into HW after power up.
The userspace has to take care to write senseful data.
Signed-off-by: Markus Proeller <markus.proeller@pieye.org>
Instead of changing the exposure and framerate settings for all sequences,
they can be changed for every sequence individually now. Therefore the
IRS1125_CID_SAFE_RECONFIG ctrl has been removed and replaced by
IRS1125_CID_SAFE_RECONFIG_S<seq_num>_EXPO and *_FRAME ctrls.
The consistency check in the sequence ctrl IRS1125_CID_SEQ_CONFIG
is removed.
Signed-off-by: Markus Proeller <markus.proeller@pieye.org>
Reading data over i2c is done by using i2c_transfer to ensure that this
operation can't be interrupted.
Signed-off-by: Markus Proeller <markus.proeller@pieye.org>
The BRCM PCIe block has controls to enable control of the CLKREQ#
signal by the L1SS, and to gate the refclk with the CLKREQ# input.
These controls are mutually exclusive - the upstream code sets the
latter, but some use cases require the former.
Add a Device Tree property - brcm,enable-l1ss - to switch to the
L1SS configuration.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Upstream Linux deems using output GPIOs to generate IRQs as a bogus
use case, even though the BCM2835 GPIO controller is capable of doing
so. A number of users would like to make use of this facility, so
disable the checks.
See: https://github.com/raspberrypi/linux/issues/2527
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Things don't work too well when both the vc4 driver and the firmware
driver are trying to control the same audio output:
[ 763.569406] bcm2835_audio bcm2835_audio: vchi message timeout, msg=5
Hence, when the vc4 HDMI driver is used, let it control audio. This is done
by introducing a new device tree property to the audio node, and
extending the vc4-kms-v3d overlays to set it appropriately.
Signed-off-by: Hristo Venev <hristo@venev.name>
Since the unicam driver was modified to write to a dummy buffer when no
user-supplied buffer is available, it can now write to and return a
buffer even when there's only a single one. Enable this by changing the
min_buffers_needed in the vb2_queue; it will be useful for enabling
still captures without allocating more memory than absolutely necessary.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Manage the split between addresses for the VPU and addresses for the
40-bit DMA controller with a dedicated DMA device pointer that on non-
BCM2711 platforms is the same as the main VCHIQ device. This allows
the VCHIQ node to stay in the usual place in the DT, and removes the
ugly VC_SAFE macros.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
staging: vchiq_arm: Use g_dma_dev for dma_unmap_sg
Commit "staging: vchiq_arm: Clean up 40-bit DMA support" failed to
change one of the calls to dma_unmap_sg to pass in g_dma_dev (rather
than g_dev). Correct that oversight.
See: https://github.com/raspberrypi/linux/issues/3647
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Without this patch GPIOs don't seem to work properly, primarily
noticeable as broken LEDs.
Squash with "pinctrl-bcm2835: Set base to 0 give expected gpio numbering"
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Enabling zswap support in the kernel configuration costs about 1.5MB
of RAM, even when zswap is not enabled at runtime. This cost can be
reduced significantly by deferring initialisation (including pool
creation) until the "enabled" parameter is set to true. There is a
small cost to this in that some initialisation code has to remain in
memory after the init phase, just in case they are needed later,
but the total size increase is negligible.
See: https://github.com/raspberrypi/linux/pull/3432
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The change to retrieve the pixel format always on g_fmt didn't
check whether the native or unpacked version of the format
had been requested, and always returned the packed one.
Correct this so that the packing setting is retained whereever
possible.
Fixes "9d59e89 media: bcm2835-unicam: Re-fetch mbus code from subdev
on a g_fmt call"
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The GCC plugin feature leads to different kernel configurations on what
ought to be equivalent build systems because they depend on the build
hosts native compilers rather than the cross compilers needed for the
target. This causes problems with module symbol version mismatches.
Disable GCC plugins for all build hosts.
Advanced build script hackery borrowed from a patch by milhouse.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
V4L2 wishes to have the codec header bytes in the same buffer as the
first encoded frame, so it does become 1-in 1-out for encoding.
The firmware now has an option to do this, so enable it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The SC16IS7XX hardware flow control is mishandled by the driver in
a number of ways:
1. The set_baud method accidentally clears it when setting EFR bit.
2. Even though hardware flow control is enabled, it isn't indicated
back to the serial framework.
3. Applying the flow control clears the EFR bit.
4. The CTS support is not indicated in the return from
sc16is7xx_get_mctrl.
Address all of those issues using a mixture of patches found on the
linked pages.
See: https://github.com/raspberrypi/linux/issues/2542
See: https://www.spinics.net/lists/linux-serial/msg21794.html
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
From when bringing up the driver, there was a check in the isr
to ignore interrupts (claiming them handled) should the driver
not be streaming.
The VPU now will not register a camera driver if it finds a
CSI2 node enabled in device tree, therefore this flawed check is
redundant.
https://github.com/raspberrypi/linux/issues/3602
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
If the firmware hasn't detected a display, the driver would assume
one display was available, but because it had failed to retrieve the
display size it would try to allocate a zero-sized buffer.
Avoid the allocation failure by bailing out early if no display is
found.
See: https://github.com/raspberrypi/linux/issues/3598
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The reference counting of node->open was only incremented after
a check that the node was v4l2_fh_is_singular_file, which resulted
in the counting going wrong and s_power not being called at an
appropriate time.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
unicam_release calls _vb2_fop_release, which will call stop_streaming
if that particular node was streaming. Calling it unconditionally (as
the code was) means that if a second handle was opened eg to alter
a setting, on closing that connection it also stopped Unicam.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Sensors are now reflecting cropping and scaling parameters through
the selection API, therefore Unicam needs to forward the requests
through to the subdev.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Exposure is clipped by the VTS of the mode, so needs to be updated as
and when this is changed.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
To make adding new members to the mode structures easier, use
the member names in the initialisers.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The controls for analogue gain and exposure were defined with
V4L2_CTRL_FLAG_EXECUTE_ON_WRITE. This is not required as we only need
to send changes to the sensor.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The ov5647 subdev can generate control events, therefore set
the V4L2_SUBDEV_FL_HAS_EVENTS flag.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Clients need to know the pixel rate in order to compute exposure
and frame rate values.
Advertise it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
"87f3ab9 media: ov5647: Add basic support for multiple sensor modes."
added a return path ov5647_set_fmt that didn't release the device
mutex that it had claimed.
Release the mutex.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
In order to apply lens shading correctly the client needs to know how
each mode crops or scales the image compared to the full sensor array.
Implement this (based on the imx219 equivalent).
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Specifically:
* AWB is now off by default.
* AEC/AGC is also off by default.
* The default mode is changed to the 10-bit 2x2 binned mode.
AWB and AEC/AGC can be re-enabled using the usual V4L2 controls. The
original 8-bit mode will be respected if an application requests the
8-bit format.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
The 8-bit VGA mode remains, we add the following 10-bit modes:
Mode 0: 2592x1944 full resolution.
Mode 1: 1920x1080 full resolution, but centre-cropped.
(This mode achieves 30fps, mode 0 does not.)
Mode 2: 1296x972 full field-of-view 2x2 binned mode.
Mode 3: VGA full field of view mode.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Added basic v4l2_ctrl_handler infrastructure (there was none
previously).
Added controls to let AWB/AEC/AGC run in the sensor's auto mode or
manually. Also controls to set exposure (in lines) and analogue gain
(as a register code) from user code.
Also delete registers (just the one) from the VGA mode register set
that are now controlled by the new V4L2 controls.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Specifically:
Added a structure ov5647_mode and a list of supported_modes (though no
actual new modes as yet). The state object points to the "current mode".
ov5647_enum_mbus_code, ov5647_enum_frame_size, ov5647_set_fmt and
ov5647_get_fmt all needed upgrading to cope with multiple modes.
__sensor_init (which writes all the registers) is now called by
ov5647_stream_on (once the mode is known) rather than by
ov5647_sensor_power.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Previously they were returning positive non-zero codes for success,
which were getting passed up the call stack. Since release 4.19,
do_dentry_open (fs/open.c) has been catching these and flagging an
error. (So this driver has been broken since that date.)
Fixes: 3c2472a [media] media: i2c: Add support for OV5647 sensor
Signed-off-by: David Plowman <david.plowman@raspberrypi.org>
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
The flag V4L2_SUBDEV_FL_HAS_EVENTS is required if the subdev can
generate events. It can create events from the ctrl handler, therefore
this is required.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Like many overlays, the i2c-gpio overlay goes to efforts to avoid
generating warnings about #address-cells and #size-cells not
being defined, which it does by defining them. Unfortunately this
is fatal if they don't match what the system requires, and the
recent switch to #size-cells = 2 on 2711 made i2c-gpio very
dangerous.
In the absence of the knowledge of a clean way to fix this, just delete
the declarations and suffer the warnings.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
BCM2711 has 4 DMA channels with a 40-bit address range, allowing them
to access the full 4GB of memory on a Pi 4.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcmn2835_isp is a platform driver dependent on vchiq,
therefore add the load/unload functions for it to vchiq.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Add V4L2_META_FMT_BCM2835_ISP_STATS V4L2 format type.
This new format will be used by the BCM2835 ISP device to return
out ISP statistics for 3A.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
The sensor subdevice may change the Bayer order if a H/V flip is
requested after a s_fmt call. Unicam g_fmt must call the subdev get_fmt
in case this has happened and return out the correct format 4cc.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
This commit updates the imx219 driver to adverise support for embedded
data streams. This can then be used by the bcm2835-unicam driver, which
has recently been updated to expose the embedded data stream to
userland.
The imx219 sensor subdevice overloads the media pad to differentiate
between image stream (pad 0) and embedded data stream (pad 1) when
performing the v4l2_subdev_pad_ops functions.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
The unicam driver supports both the SOURCE_CHANGE and CTRL events. Both
events are only generated on the image video node, so the event-related
ioctls are useless on the medatada node. Disable them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
If no buffer has been queued by a userland application, we use an
internal dummy buffer for the hardware to spin in. This will allow
the driver to release the existing userland buffer back to the
application for processing.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
This patch adds a new node in the bcm2835-unicam driver to support
CSI-2 embedded data streams. The subdevice is queried to see if
embedded data is available from the sensor.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Move device node specific state out of the device state structure and
into a new node structure. This separation will be needed for future
changes where we will add an embedded data node to the driver to work
alongside the existing image data node.
Currently only use a single image node, so this commit does not add
any functional changes.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
This patch adds MEDIA_BUS_FMT_SENSOR_DATA used by the bcm2835-unicam
driver to support CSI-2 embedded data streams from camera sensors.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Add V4L2_META_FMT_SENSOR_DATA format 4CC.
This new format will be used by the BCM2835 Unicam device to return
out camera sensor embedded data.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Add driver for the Unicam camera receiver block on
BCM283x processors.
This commit is made up of a series of changes cherry-picked from the
rpi-4.19.y branch.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Limit mappings to the permitted range, but don't map more than asked
for otherwise we walk off the end of the allocated VMA.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Commit f3186dd876 ("spi: Optionally use GPIO descriptors for CS GPIOs")
amended of_spi_parse_dt() to always set SPI_CS_HIGH for SPI slaves whose
Chip Select is defined by a "cs-gpios" devicetree property.
This change breaks drivers whose probe functions set the mode field of
the spi_device because in doing so they clear the SPI_CS_HIGH flag.
Fix by setting SPI_CS_HIGH in spi_setup (under the same conditions as
in of_spi_parse_dt()).
See also: 83b2a8fe43 ("spi: spidev: Fix CS polarity if GPIO descriptors are used")
Fixes: f3186dd876 ("spi: Optionally use GPIO descriptors for CS GPIOs")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
SQUASH: spi: Demote SPI_CS_HIGH warning to KERN_DEBUG
This warning is unavoidable from a client's perspective and
doesn't indicate anything wrong (just surprising).
SQUASH with "spi: use_gpio_descriptor fixup moved to spi_setup"
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
framebuffer_check was computing a minimum pitch value and ensuring
that the provided value was greater than this.
That check is only valid if the format is linear.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The HDMI controllers found in the BCM2711 SoC need some adjustments to the
bindings, especially since the registers have been shuffled around in more
register ranges.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
When the MMC isn't plugged in, the driver will spam the console which is
pretty annoying when using NFS.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
This driver is for the HEVC/H265 decoder block on the Raspberry
Pi 4, and conforms to the V4L2 stateless decoder API.
Signed-off-by: John Cox <jc@kynesim.co.uk>
Allow the capture buffer to be detached from a v4l2 request job such
that another job can start before the capture buffer is returned. This
allows h/w codecs that can process multiple requests at the same time
to operate more efficiently.
Signed-off-by: John Cox <jc@kynesim.co.uk>
Some of the Broadcom codec blocks use a column based YUV4:2:0 image
format, so add the documentation and defines for both 8 and 10 bit
versions.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
WPP can allow greater parallelism within the decode, but needs
offset information to be passed in.
Adds num_entry_point_offsets and entry_point_offset_minus1 to
v4l2_ctrl_hevc_slice_params.
This is based on Jernej Skrabec's patches for cedrus which
implement the same feature.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
From https://patchwork.linuxtv.org/patch/60725/
Changes requested, but mainly docs.
If HEVC frame consists of multiple slices, segment address has to be
known in order to properly decode it.
Add segment address field to slice parameters.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Adds a format that is 3 10bit YUV 4:2:0 samples packed into
a 32bit work (with 2 spare bits).
Supported on Broadcom BCM2711 chips.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
This is adjustment to commit
d368ceaacd "kbuild: Allow .dtbo overlays to be built piecemeal"
prepare3 target has gone from mainline tree in branch 5.4.y
Signed-off-by: Nataliya Korovkina <malus.brandywine@gmail.com>
The DT bindings description of the Brcmstb PCIe device is described. This
node can be used by almost all Broadcom settop box chips, using
ARM, ARM64, or MIPS CPU architectures.
Signed-off-by: Jim Quinlan <jim2101024@gmail.com>
When symbols from overlays are added to the live tree their paths must
be rebased. The translated symbol is normally the result of joining
the fragment-relative path (with a leading "/") to the target path
(either copied directly from the "target-path" property or resolved
from the phandle). This translation fails when the target is the root
node (a common case for Raspberry Pi overlays) because the resulting
path starts with a double slash. For example, if target-path is "/" and
the fragment adds a node called "newnode", the label associated with
that node will be assigned the path "//newnode", which can't be found
in the tree.
Fix the failure case by explicitly replacing a target path of "/" with
an empty string.
Fixes: d1651b03c2 ("of: overlay: add overlay symbols to live device tree")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The definition of compat_ptr is now common for most platforms, but
requires the inclusion of <linux/compat.h>.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The definition of compat_ptr is now common for most platforms, but
requires the inclusion of <linux/compat.h>.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The downstream .dts files only request two GPIO IRQs. Truncate the
array of parent IRQs when irq_of_parse_and_map returns 0.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
pinctrl-bcm2835 is a combined pinctrl/gpio driver. Currently the gpio
side is registered first, but this breaks gpio hogs (which are
configured during gpiochip_add_data). Part of the hog initialisation
is a call to pinctrl_gpio_request, and since the pinctrl driver hasn't
yet been registered this results in an -EPROBE_DEFER from which it can
never recover.
Change the initialisation sequence to register the pinctrl driver
first.
See: https://www.raspberrypi.org/forums/viewtopic.php?f=107&t=260600
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
A failure in gpiochip_irqchip_add leads to a leak of a gpiochip. Fix
the leak with the use of devm_gpiochip_add_data.
Fixes: 85ae9e512f ("pinctrl: bcm2835: switch to GPIOLIB_IRQCHIP")
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
vchiq kernel clients are now instantiated as platform drivers rather
than using DT, but the children of the vchiq interface may still
benefit from access to DT properties. Give them the option of a
a sub-node of the vchiq parent for configuration and to allow
them to be disabled.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The IMA (Integrity Measurement Architecture) looks for a TPM (Trusted
Platform Module) having been registered when it initialises; otherwise
it assumes there is no TPM. It has been observed on BCM2835 that IMA
is initialised before TPM, and that initialising the BCM2835 clock
driver before the firmware driver has the effect of reversing this
order.
Change the firmware driver to initialise at core_initcall, delaying the
BCM2835 clock driver to postcore_initcall.
See: https://github.com/raspberrypi/linux/issues/3291https://github.com/raspberrypi/linux/pull/3297
Signed-off-by: Luke Hinds <lhinds@redhat.com>
Co-authored-by: Phil Elwell <phil@raspberrypi.org>
vchiq on Pi4 is no longer under the soc node, therefore it
doesn't get the dma-ranges for the VPU.
Switch to using the configuration of the old dma controller as
that will set the dma-ranges correctly.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
The VCHIQ driver now loads the audio, camera, codec, and vc-sm
drivers as platform drivers. However they were not being given
the correct DMA configuration.
Call of_dma_configure with the parent (VCHIQ) parameters to be
inherited by the child.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Both coherent_dma_mask and dma_mask act as constraints on allocations
and bounce buffer usage, so be sure to set dma_mask to the appropriate
value otherwise the effective mask could be incorrect.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
For performance/power it is beneficial to adjust gpu clocks with arm clock.
This is how the downstream cpufreq driver works
Signed-off-by: popcornmix <popcornmix@gmail.com>
Setting the v3d clock to low value allows firmware to handle dvfs in case
where v3d hardware is not being actively used (e.g. console use).
Signed-off-by: popcornmix <popcornmix@gmail.com>
Add device tree entries and code to allow the specification of
the lighting modes for the LED's on the ethernet connector.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
Following the same pattern as bcm2835-camera and bcm2835-audio,
register the V4L2 codec driver as a platform driver
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Following the same pattern as bcm2835-camera and bcm2835-audio,
register the vcsm-cma driver as a platform driver
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The irq_fence and done_fence are given a reference that is never
released. The necessary dma_fence_put()s seem to have been
deleted in error in an earlier commit.
Fixes: 0b73676836b2 ("drm/v3d: Clock V3D down when not in use.")
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The v3d driver currently encounters a lot of MMU PTE exceptions, so
only log the first to avoid swamping the kernel log.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
MMU exception conditions are reported in the V3D_MMU_CTRL register as
write-1-to-clear (W1C) bits. The MMU interrupt handling code clears any
exceptions, but does so by masking out any other bits and writing the
result back. There are some important control bits in that register,
including MMU_ENABLE, so a safer approach is to simply write back the
value just read unaltered.
This patch doesn't remove the cause of the apparent PTE errors, but it
does reduce the impact to just an error in the kernel log.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The Infineon IRS1125 is a time of flight depth sensor that
has a CSI-2 interface.
Add a V4L2 subdevice driver for this device.
Signed-off-by: Markus Proeller <markus.proeller@pieye.org>
HDMI Alsa devices renamed to match names used by DRM, to
HDMI 1 and HDMI 2
Check for which HDMI devices are connected and only create
devices for those that are present.
The rename of the devices might cause some backwards compatibility
issues, but since this particular part of the driver needs to be
specifically enabled, I suspect the number of people who will see
the problem will be very small.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
After the decision to use bcm2711 compatible for upstream, we should
switch all accepted compatibles to bcm2711. So we can boot with
one DTB the down- and the upstream kernel.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Before 4.20, it was possible to build an arbitrary overlay by copying
it to arm/boot/dts/overlays/mytest-overlay.dts and running:
make ARCH=arm overlays/mytest.dtbo
In 4.20 the .dtb build rules were centralised, requiring the dowstream
.dtbo build rules to be changed. They were, enough to support "make ...
dtbs", but not sufficiently to allow this ad-hoc, one-off building of
individual files.
Add the missing makefile rule to support this way of building.
See: https://github.com/raspberrypi/linux/issues/3250
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
This is mainly used for the NoIR camera which has no IR
filter and can completely confuse normal AWB presets.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Adds a simple greyworld white balance preset, mainly for use
with cameras without an IR filter (eg Raspberry Pi NoIR)
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
The IMX219 is an 8MPix CSI2 sensor, supporting 2 or 4 data lanes.
Document the binding for this device.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Users have reported log spam created by "Event Ring Full" xHC event
TRBs. These are caused by interrupt latency in conjunction with a very
busy set of devices on the bus. The errors are benign, but throughput
will suffer as the xHC will pause processing of transfers until the
event ring is drained by the kernel. Expand the number of event TRB slots
available by increasing the number of event ring segments in the ERST.
Controllers have a hardware-defined limit as to the number of ERST
entries they can process, so make the actual number in use
min(ERST_MAX_SEGS, hw_max).
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Some combinations of Pi 4Bs and Ethernet switches don't reliably get a
DCHP-assigned IP address, leaving the unit with a self=assigned 169.254
address. In the failure case, the Pi is left able to receive packets
but not send them, suggesting that the MAC<->PHY link is getting into
a bad state.
It has been found empirically that skipping a reset step by the genet
driver prevents the failures. No downsides have been discovered yet,
and unlike the forced renegotiation it doesn't increase the time to
get an IP address, so the workaround is enabled by default; add
genet.skip_umac_reset=n
to the command line to disable it.
See: https://github.com/raspberrypi/linux/issues/3108
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
These wireless mouse/keyboard combo remote control devices specify
multiple "wheel" events in their report descriptors. The wheel events
are incorrectly defined and apparently map to accelerometer data, leading
to spurious mouse scroll events being generated at an extreme rate when
the device is moved.
As a workaround, use HID_QUIRK_INCREMENT_USAGE_ON_DUPLICATE to mask
feeding the extra wheel events to the input subsystem.
See: https://github.com/raspberrypi/firmware/issues/1189
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Based on the gpiomem driver, allow mapping of the decoder register
spaces such that userspace can access control/status registers.
This driver is intended for use with a custom ffmpeg backend accelerator
prior to a v4l2 driver being written.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
driver: char: rpivid: Destroy the legacy device on remove
The legacy name support created a new device that was never destroyed.
If the driver was unloaded and reloaded, it failed due to the
device already existing.
Fixes: "75f1d14 driver: char: rpivid - also support legacy name"
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
driver: char: rpivid: Clean up error handling use of ERR_PTR/IS_ERR
The driver used an unnecessary intermediate void* variable so it
only called ERR_PTR once to convert to the error value.
Switch to converting as the error arises to remove these intermediate
variables.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
driver: char: rpivid: Add error handling to the legacy device load
The return value from device_create for the legacy device was never
checked or handled. Add the required error handling.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
driver: char: rpivid: Fix coding style whitespace issues.
Makes checkpatch happier.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
driver: char: rpimem: Add SPDX licence header.
Stops checkpatch complaining.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
driver: char: rpivid: Fix access to freed memory
The error path during probe frees the private memory block, and
then promptly dereferences it to log an error message.
Use the base device instead of the pointer to it in the private
structure.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
My various attempts at re-enabling runtime PM have failed, so just
crank the clock down when V3D is idle to reduce power consumption.
Signed-off-by: Eric Anholt <eric@anholt.net>
Something is still unstable -- on starting a new glxgears from an idle
X11, I get an MMU violation in high addresses. The CTS also failed
quite quickly. With this, CTS progresses for an hour before OOMing
(allocating some big buffers when my board only has 600MB available to
Linux)
Signed-off-by: Eric Anholt <eric@anholt.net>
The BCM2835 I2C blocks have a register to set the clock-stretch
timeout - how long the device is allowed to hold SCL low - in bus
cycles. The current driver doesn't write to the register, therefore
the default value of 64 cycles is being used for all devices.
Set the timeout to the value recommended for SMBus - 35ms.
See: https://github.com/raspberrypi/linux/issues/3064
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Seen on a VLI VL805 PCIe to USB controller. For non-stream endpoints
at least, if the xHC halts on a particular TRB due to an error then
the DCS field in the Out Endpoint Context maintained by the hardware
is not updated with the current cycle state.
Using the quirk XHCI_EP_CTX_BROKEN_DCS and instead fetch the DCS bit
from the TRB that the xHC stopped on.
See: https://github.com/raspberrypi/linux/issues/3060
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
In translating the runtime PM code from vc4, I missed the ".pm"
assignment to actually connect them up. Fixes missing MMU setup if
runtime PM resets V3D.
Signed-off-by: Eric Anholt <eric@anholt.net>
(cherry picked from commit ca197699af29baa8236c74c53d4904ca8957ee06)
If it's off, we know it will be reset on poweron, so the MMU won't
have any TLB cached from before this point. Avoids failed waits for
MMU flush to reply.
Signed-off-by: Eric Anholt <eric@anholt.net>
(cherry picked from commit 3ee4e2e0a9e9587eacbb69b067bbc72ab2cdc47b)
Must be called in a non-atomic context, after the endpoint
has been registered with the hardware via xhci_add_endpoint
and before the first URB is submitted for the endpoint.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
xHCI caches device and endpoint data after the interface is configured,
so an explicit command needs to be issued for any device driver wanting
to alter the polling interval of an endpoint.
Add usb_fixup_endpoint() to allow drivers to do this. The fixup must be
called after calculating endpoint bandwidth requirements but before any
URBs are submitted.
If polling intervals are shortened, any bandwidth reservations are no
longer valid but in practice polling intervals are only ever relaxed.
Limit the scope to interrupt transfers for now.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
This falls under the same "we can reprogram glitch-free as long as we
pause generation" rule as updating the div/frac fields. This can be
used for runtime reclocking of V3D to manage power leakage.
Signed-off-by: Eric Anholt <eric@anholt.net>
Without the actual power management part any more, there's a lot less
to set up for V3D. We just need to clear the RSTN field for the power
domain, and expose the reset controller for toggling it again.
This is definitely incomplete -- the old ISP and H264 is in the old
bridge, but since we have no consumers of it I've just done the
minimum to get V3D working.
Signed-off-by: Eric Anholt <eric@anholt.net>
If the VL805 EEPROM has not been programmed then boot will hang for five
seconds. The timeout seems to be arbitrary and is an unecessary
delay on the first boot. Remove the timeout.
This is common code and probably can't be upstreamed unless the timeout
can be configurable somehow or perhaps the XHCI driver can be skipped
on the first boot.
There are several warts surrounding bcmgenet_mii_probe() as this
function is called from ndo_open, but it's calling registration-type
functions. The probe should be called at probe time and refactored
such that the PHY device data can be extracted to limit the scope
of this flag to Broadcom PHYs.
For now, pass this flag in as it puts our attached PHY into a low-power
state when disconnected.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Set defaults for TX and RX packet coalescing to be equivalent to:
# ethtool -C eth0 tx-frames 10
# ethtool -C eth0 rx-usecs 50
This may be something we want to set via DT parameters in the
future.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Conditional on a new compatible string, change the pagelist encoding
such that the top 24 bits are the pfn, leaving 8 bits for run length
(-1).
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
staging/vchiq_arm: Fix bcm2711 compatible string
Fixes: "vchiq: Add 36-bit address support"
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The Linux support for controlling card power via regulators appears to
be contentious. I would argue that the default behaviour is contrary to
the SDHCI spec - turning off the power writes a reserved value to the
SD Bus Voltage Select field of the Power Control Register, which
seems to kill the Arasan/iProc controller - but fortunately there is a
hook in sdhci_ops to override the behaviour. Borrow the implementation
from sdhci_arasan_set_power.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The HWRNG on the BCM2838 is compatible to iproc-rng200, so add the
support to this driver instead of bcm2835-rng.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
hwrng: iproc-rng200: Correct SoC name
The Pi 4 SoC is called BCM2711, not BCM2838.
Fixes: "hwrng: iproc-rng200: Add BCM2838 support"
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The legacy peripherals can only address the first gigabyte of RAM, so
ensure that DMA allocations are restricted to that region.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The ioremapping creates mappings within the vmalloc area. The
equivalent early function, create_mapping, now checks that the
requested explicit virtual address is between VMALLOC_START and
VMALLOC_END. As there is no reason to have any correlation between
the physical and virtual addresses, put the required mappings at
VMALLOC_START and above.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
On error, vchiq_mmal_component_init could leave the
event context allocated for ports.
Clean them up in the error path.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
vchiq_mmal_component_init calls init_event_context for the
control port, but vchiq_mmal_component_finalise didn't free
it, causing a memory leak..
Add the free call.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
mmal_parameters.h hasn't been updated to reflect additions made
over the last few years. Update it to reflect the currently
supported parameters.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
The list of formats was copied before Bayer support was added.
The ISP supports Bayer and is being supported by the bcm2835_codec
driver, so add in the encodings for them.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
All calls to the gpio library are in contexts that can sleep,
therefore there is no issue with having those GPIOs controlled
by controllers which require sleeping (eg I2C GPIO expanders).
Switch to using gpiod_set_value_cansleep instead of gpiod_set_value
to avoid triggering the warning in gpiolib should the GPIO
controller need to sleep.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
The debug text for how many clocks have been registered
uses "%d" with a size_t. Correct it to "%zd".
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
The MMAL client_component field is used with the event
mechanism to allow the client to identify the component for
which the event is generated.
The field is only 32bits in size, therefore we can't use a
pointer to the component in a 64 bit kernel.
Component handles are already held in an array per VCHI
instance, so use the array index as the client_component handle
to avoid having to create a new IDR for this purpose.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
videobuf2 only allowed exporting a dmabuf as a file descriptor,
but there are instances where having the struct dma_buf is
useful within the kernel.
Split the current implementation into two, one step which
exports a struct dma_buf, and the second which converts that
into an fd.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Add the ability to send data to ports. This only supports
zero copy mode as the required bulk transfer setup calls
are not done.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
(Preparation for the codec driver).
The codec uses the event mechanism to report things such as
resolution changes. It is signalled by the cmd field of the buffer
being non-zero.
Add support for passing this information out to the client.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Fixes up a checkpatch error "Avoid using bool structure members
because of possible alignment issues".
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
When calling tc358743_set_fmt, the code was calling tc358743_get_fmt
to choose a valid format. However that sets the colorspace
based on what was read back from the chip. When you set the format,
then the driver would choose and program the colorspace based
on the format code.
The result was that if you called try or set format for UYVY
when the current format was RGB3 then you would get told sRGB,
and try RGB3 when current was UYVY and you would get told
SMPTE170M.
The value programmed into the chip is determined by this driver,
therefore there is no need to read back the value. Return the
colorspace based on the format set/tried instead.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Document the DT bindings for the CSI2/CCP2 receiver peripheral
(known as Unicam) on BCM283x SoCs.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Acked-by: Rob Herring <robh@kernel.org>
New helper defines that allow printing of a FOURCC using
printf(V4L2_FOURCC_CONV, V4L2_FOURCC_CONV_ARGS(fourcc));
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
The ADV7282M can support YPbPr on AIN1-3, but this was
not selectable from the driver. Add it to the list of
supported input modes.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
The hardware default is differential CVBS on AIN1 & 2, which
isn't very useful.
Select the first input that is defined as valid for the
chip variant (typically CVBS_AIN1).
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
The probe for the TC358743 reads the CHIPID register from
the device and compares it to the expected value of 0.
If the I2C request fails then that also returns 0, so
the driver loads thinking that the device is there.
Generally I2C communications are reliable so there is
limited need to check the return value on every transfer,
therefore only amend the one read during probe to check
for I2C errors.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Adds register setups for running the CSI lanes at 972Mbit/s,
which allows 1080P50 UYVY down 2 lanes.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
g_mbus_config was supposed to indicate all supported lane numbers, not
only the number of those currently in active use. Since the TC358743
can dynamically reduce the number of active lanes if the required
bandwidth allows for it, report all lane numbers up to the connected
number of lanes as supported in pdata mode.
In device tree mode, do not report lane count and clock mode at all, as
the receiver driver can determine these from the device tree.
To allow communicating the number of currently active lanes, add a new
bitfield to the v4l2_mbus_config flags. This is a temporary fix, to be
used only until a better solution is found.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The existing fixed value of 16 worked for UYVY 720P60 over
2 lanes at 594MHz, or UYVY 1080P60 over 4 lanes. (RGB888
1080P60 needs 6 lanes at 594MHz).
It doesn't allow for lower resolutions to work as the FIFO
underflows.
374 is required for 1080P24-30 UYVY over 2 lanes @ 972Mbit/s, but
>374 means that the FIFO underflows on 1080P50 UYVY over 2 lanes
@ 972Mbit/s.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
The driver was only supporting continuous clock mode
although this was not stated anywhere.
Non-continuous clock saves a small amount of power and
on some SoCs is easier to interface with.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
There's no way to query the subdevice for the supported
resolutions.
Add set_fmt and get_fmt implementations.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
The lan78xx uses a 12-byte hardware rx header, so there is no need
to allocate SKBs with NET_IP_ALIGN set. Removes alignment faults
in both dwc_otg and in ipv6 processing.
Add the ability to interpret the high bits of the dreq specifier as
flags to be included in the DMA_CS register. The motivation for this
change is the ability to set the DISDEBUG flag for SD card transfers
to avoid corruption when using the VPU debugger.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The bInterval is set to 4 (i.e. 8 microframes => 1ms) and the only bit
that the driver pays attention to is "link was reset". If there's a
flapping status bit in that endpoint data, (such as if PHY negotiation
needs a few tries to get a stable link) then polling at a slower rate
would act as a de-bounce.
See: https://github.com/raspberrypi/linux/issues/2447
The driver already reported the firmware build date during probe.
The mailbox calls have been extended to also report the variant
1 = standard start.elf
2 = start_x.elf (includes camera stack)
3 = start_db.elf (includes assert logging)
4 = start_cd.elf (cutdown version for smallest memory footprint).
Log the variant during probe.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
firmware: raspberrypi: Report the fw git hash during probe
The firmware can now report the git hash from which it was built
via the mailbox, so report it during probe.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Ethernet cables with faulty or missing pairs (specifically pairs C and
D) allow auto-negotiation to 1000Mbs, but do not support the successful
establishment of a link. Add a DT property, "microchip,downshift-after",
to configure the number of auto-negotiation failures after which it
falls back to 100Mbs. Valid values are 2, 3, 4, 5 and 0, where 0 means
never downshift.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Step wise governor increases the mitigation level when the temperature
goes above a threshold and will decrease the mitigation when the
temperature falls below the threshold. If it were a case, where the
temperature hovers around a threshold, the mitigation will be applied
and removed at every iteration. This reaction to the temperature is
inefficient for performance.
The use of hysteresis temperature could avoid this ping-pong of
mitigation by relaxing the mitigation to happen only when the
temperature goes below this lower hysteresis value.
Signed-off-by: Ram Chandrasekar <rkumbako@codeaurora.org>
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Avoid a hard userspace ABI change by adding a compatible get_throttled
sysfs entry. Its value is now feed by the GET_THROTTLED requests of the
new hwmon driver. The first access to get_throttled will generate
a warning.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Although the correct fix for low voltage warnings is to
improve the power supply, the current implementation
of the detection can fill the log if the warning
happens freqently. This replaces the logging with
slightly custom ratelimited logging.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Enable EEE mode as soon as possible after connecting to the PHY, and
before phy_start. This avoids a second link negotiation, which speeds
up booting and stops the interface failing to become ready.
See: https://github.com/raspberrypi/linux/issues/2437
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
As of 4.18, a firmware that implements the update_connect_params
method but doesn't claim to support roaming causes an error. We
disabled firmware roaming in 4.4 [1] because it appeared to
prevent disconnects, but let's try with the current firmware to see
if things have improved.
[1] dd91880117
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The published API to the dynamic overlay application mechanism now
takes a Flattened Device Tree blob as input so that it can manage the
lifetime of the unflattened tree. Conveniently, the new API call -
of_overlay_fdt_apply - is virtually a drop-in replacement for
create_overlay, which can now be deleted.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
ad83c7cb2f ("irqchip/irq-bcm2836: Add support for DT interrupt polarity")
changed the way that the BCM2836/7 local interrupts are mapped; instead
of being pre-mapped they are now mapped on-demand. A side effect of this
change is that the call to irq_of_parse_and_map from armctrl_of_init
creates a new mapping, forming a gap between the IRQs and the FIQs. This
gap breaks the FIQ<->IRQ mapping which up to now has been done by assuming:
1) that the value of FIQ_START is the same as the number of normal IRQs
that will be mapped (still true), and
2) that this value is also the offset between an IRQ and its equivalent
FIQ (which is no longer the case).
Remove both assumptions by measuring the interval between the last IRQ
and the last FIQ, passing it as the parameter to init_FIQ().
Fixes: https://github.com/raspberrypi/linux/issues/2432
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Register for reboot notifications, sending RPI_FIRMWARE_NOTIFY_REBOOT
over the mailbox interface on reception.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Add two new DT properties:
* microchip,eee-enabled - a boolean to enable EEE
* microchip,tx-lpi-timer - time in microseconds to wait before entering
low power state
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
I2C busses can be assigned specific bus numbers using aliases in
Device Tree - string properties where the name is the alias and the
value is the path to the node. The current DT parameter mechanism
does not allow property names to be derived from a parameter value
in any way, so it isn't possible to generate unique or matching
aliases for nodes from an overlay that can generate multiple
instances, e.g. i2c-gpio.
Work around this limitation (at least temporarily) by allowing
the i2c adapter number to be initialised from the "reg" property
if present.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
There is a new test in __irq_startup that the IRQ is activated, which
hasn't been the case for FIQs since they bypass some of the usual setup.
Augment enable_fiq to include a call to irq_activate to avoid the
warning.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Create a semi-static mapping for the USB registers early in the boot
process, before additional kernel threads are started, so all threads
will have the mappings from the start. This avoids the need for
data aborts to lazily update them.
See: https://github.com/raspberrypi/linux/issues/2450
Signed-off-by: Floris Bos <bos@je-eigen-domein.nl>
The VideoCore bootloader passes in Serial number and
Revision number through Device Tree. Make these available to
userspace through /proc/cpuinfo.
Mainline status:
There is a commit in linux-next that standardize passing the serial
number through Device Tree (string: /serial-number):
ARM: 8355/1: arch: Show the serial number from devicetree in cpuinfo
There was an attempt to do the same with the revision number, but it
didn't get in:
[PATCH v2 1/2] arm: devtree: Set system_rev from DT revision
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Uses the debugfs I/F to provide access to the AXI
bus performance monitors.
Requires the new mailbox peripheral access for access
to the VPU performance registers, system bus access
is done using direct register reads.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
raspberrypi_axi_monitor: suppress warning
Suppress the following warning by casting the pointer to and uintptr_t
before to u32:
Signed-off-by: Matteo Croce <mcroce@redhat.com>
IRQ-CPU mapping is round robined on ARM64 to increase
concurrency and allow multiple interrupts to be serviced
at a time. This reduces the need for FIQ.
Signed-off-by: Michael Zoran <mzoran@crowfest.net>
brcmfmac: Disable power management
Disable wireless power saving in the brcmfmac WLAN driver. This is a
temporary measure until the connectivity loss resulting from power
saving is resolved.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
brcmfmac: Use original country code as a fallback
Commit 73345fd212:
brcmfmac: Configure country code using device specific settings
prevents region codes from working on devices that lack a region code
translation table. In the event of an absent table, preserve the old
behaviour of using the provided code as-is.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
brcmfmac: Plug memory leak in brcmf_fill_bss_param
See: https://github.com/raspberrypi/linux/issues/1471
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
brcmfmac: do not use internal roaming engine by default
Some evidence of curing disconnects with this disabled, so make it a default.
Can be overridden with module parameter roamoff=0
See: http://projectable.me/optimize-my-pi-wi-fi/
brcmfmac: Change stop_ap sequence
Patch from Broadcom/Cypress to resolve a customer error
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Revert "brcmfmac: Disable power management"
Shortly after the release of the Pi 3B, a loss of SSH connectivity
over WiFi was traced to the power management handling, so power
management was disabled. And so it has remained ever since.
Enabling power management saves 55mA (~270mW) on a Pi 4B, so is very
much worth the minimal effort of reverting this patch, which was
squashed and rebased many times since then to the commit hash is
meaningless.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
This is a port of Pantelis Antoniou's v3 port that makes use of the
new upstreamed configfs support for binary attributes.
Original commit message:
Add a runtime interface to using configfs for generic device tree overlay
usage. With it its possible to use device tree overlays without having
to use a per-platform overlay manager.
Please see Documentation/devicetree/configfs-overlays.txt for more info.
Changes since v2:
- Removed ifdef CONFIG_OF_OVERLAY (since for now it's required)
- Created a documentation entry
- Slight rewording in Kconfig
Changes since v1:
- of_resolve() -> of_resolve_phandles().
Originally-signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
DT configfs: Fix build errors on other platforms
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
DT configfs: fix build error
There is an error when compiling rpi-4.6.y branch:
CC drivers/of/configfs.o
drivers/of/configfs.c:291:21: error: initialization from incompatible pointer type [-Werror=incompatible-pointer-types]
.default_groups = of_cfs_def_groups,
^
drivers/of/configfs.c:291:21: note: (near initialization for 'of_cfs_subsys.su_group.default_groups.next')
The .default_groups is linked list since commit
1ae1602de0.
This commit uses configfs_add_default_group to fix this problem.
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
configfs: New of_overlay API
Add a mailbox-driven backlight controller for the Raspberry Pi DSI
touchscreen display. Requires updated GPU firmware to recognise the
mailbox request.
Signed-off-by: Gordon Hollingworth <gordon@raspberrypi.org>
Add Raspberry Pi firmware driver to the dependencies of backlight driver
Otherwise the backlight driver fails to build if the firmware
loading driver is not in the kernel
Signed-off-by: Alex Riesen <alexander.riesen@cetitec.com>
The driver crashed while a NULL pointer returned by i2c_get_adapter()
has been used to access the i2c bus functions.
The headphone probing function hb_hp_probe() now returns -EPROBE_DEFER
in case the i2c module has not been loaded yet.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
ASoC: Add support for Rpi-DAC
ASoC: Add prompt for ICS43432 codec
Without a prompt string, a config setting can't be included in a
defconfig. Give CONFIG_SND_SOC_ICS43432 a prompt so that Pi soundcards
can use the driver.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Add IQaudIO Sound Card support for Raspberry Pi
Set a limit of 0dB on Digital Volume Control
The main volume control in the PCM512x DAC has a range up to
+24dB. This is dangerously loud and can potentially cause massive
clipping in the output stages. Therefore this sets a sensible
limit of 0dB for this control.
Allow up to 24dB digital gain to be applied when using IQAudIO DAC+
24db_digital_gain DT param can be used to specify that PCM512x
codec "Digital" volume control should not be limited to 0dB gain,
and if specified will allow the full 24dB gain.
Modify IQAudIO DAC+ ASoC driver to set card/dai config from dt
Add the ability to set the card name, dai name and dai stream name, from
dt config.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
IQaudIO: auto-mute for AMP+ and DigiAMP+
IQAudIO amplifier mute via GPIO22. Add dt params for "one-shot" unmute
and auto mute.
Revision 2, auto mute implementing HiassofT suggestion to mute/unmute
using set_bias_level, rather than startup/shutdown....
"By default DAPM waits 5 seconds (pmdown_time) before shutting down
playback streams so a close/stop immediately followed by open/start
doesn't trigger an amp mute+unmute."
Tested on both AMP+ (via DAC+) and DigiAMP+, with both options...
dtoverlay=iqaudio-dacplus,unmute_amp
"one-shot" unmute when kernel module loads.
dtoverlay=iqaudio-dacplus,auto_mute_amp
Unmute amp when ALSA device opened by a client. Mute, with 5 second delay
when ALSA device closed. (Re-opening the device within the 5 second close
window, will cancel mute.)
Revision 4, using gpiod.
Revision 5, clean-up formatting before adding mute code.
- Convert tab plus 4 space formatting to 2x tab
- Remove '// NOT USED' commented code
Revision 6, don't attempt to "one-shot" unmute amp, unless card is
successfully registered.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
ASoC: iqaudio-dac: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: iqaudio-dac: use modern dai_link style
Signed-off-by: Matthias Reichl <hias@horus.com>
Added support for HiFiBerry DAC+
The driver is based on the HiFiBerry DAC driver. However HiFiBerry DAC+ uses
a different codec chip (PCM5122), therefore a new driver is necessary.
Add support for the HiFiBerry DAC+ Pro.
The HiFiBerry DAC+ and DAC+ Pro products both use the existing bcm sound driver with the DAC+ Pro having a special clock device driver representing the two high precision oscillators.
An addition bug fix is included for the PCM512x codec where by the physical size of the sample frame is used in the calculation of the LRCK divisor as it was found to be wrong when using 24-bit depth sample contained in a little endian 4-byte sample frame.
Limit PCM512x "Digital" gain to 0dB by default with HiFiBerry DAC+
24db_digital_gain DT param can be used to specify that PCM512x
codec "Digital" volume control should not be limited to 0dB gain,
and if specified will allow the full 24dB gain.
Add dt param to force HiFiBerry DAC+ Pro into slave mode
"dtoverlay=hifiberry-dacplus,slave"
Add 'slave' param to use HiFiBerry DAC+ Pro in slave mode,
with Pi as master for bit and frame clock.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
Fixed a bug when using 352.8kHz sample rate
Signed-off-by: Daniel Matuschek <daniel@hifiberry.com>
ASoC: pcm512x: revert downstream changes
This partially reverts commit 185ea05465
which was added by https://github.com/raspberrypi/linux/pull/1152
The downstream pcm512x changes caused a regression, it broke normal
use of the 24bit format with the codec, eg when using simple-audio-card.
The actual bug with 24bit playback is the incorrect usage
of physical_width in various drivers in the downstream tree
which causes 24bit data to be transmitted with 32 clock
cycles. So it's not the pcm512x that needs fixing, it's the
soundcard drivers.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: hifiberry_dacplus: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: hifiberry_dacplus: transmit S24_LE with 64 BCLK cycles
Signed-off-by: Matthias Reichl <hias@horus.com>
hifiberry_dacplus: switch to snd_soc_dai_set_bclk_ratio
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: hifiberry_dacplus: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add driver for rpi-proto
Forward port of 3.10.x driver from https://github.com/koalo
We are using a custom board and would like to use rpi 3.18.x
kernel. Patch works fine for our embedded system.
URL to the audio chip:
http://www.mikroe.com/add-on-boards/audio-voice/audio-codec-proto/
Playback tested with devicetree enabled.
Signed-off-by: Waldemar Brodkorb <wbrodkorb@conet.de>
ASoC: rpi-proto: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add Support for JustBoom Audio boards
justboom-dac: Adjust for ALSA API change
As of 4.4, snd_soc_limit_volume now takes a struct snd_soc_card *
rather than a struct snd_soc_codec *.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
ASoC: justboom-dac: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Also remove hw_params as it's no longer needed.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: justboom-dac: use modern dai_link style
Signed-off-by: Matthias Reichl <hias@horus.com>
New AudioInjector.net Pi soundcard with low jitter audio in and out.
Contains the sound/soc/bcm ALSA machine driver and necessary alterations to the Kconfig and Makefile.
Adds the dts overlay and updates the Makefile and README.
Updates the relevant defconfig files to enable building for the Raspberry Pi.
Thanks to Phil Elwell (pelwell) for the review, simple-card concepts and discussion. Thanks to Clive Messer for overlay naming suggestions.
Added support for headphones, microphone and bclk_ratio settings.
This patch adds headphone and microphone capability to the Audio Injector sound card. The patch also sets the bit clock ratio for use in the bcm2835-i2s driver. The bcm2835-i2s can't handle an 8 kHz sample rate when the bit clock is at 12 MHz because its register is only 10 bits wide which can't represent the ch2 offset of 1508. For that reason, the rate constraint is added.
ASoC: audioinjector-pi-soundcard: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
New driver for RRA DigiDAC1 soundcard using WM8741 + WM8804
ASoC: digidac1-soundcard: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add support for Dion Audio LOCO DAC-AMP HAT
Using dedicated machine driver and pcm5102a codec driver.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
ASoC: dionaudio_loco: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Allo Piano DAC boards: Initial 2 channel (stereo) support (#1645)
Add initial 2 channel (stereo) support for Allo Piano DAC (2.0/2.1) boards,
using allo-piano-dac-pcm512x-audio overlay and allo-piano-dac ALSA ASoC
machine driver.
NB. The initial support is 2 channel (stereo) ONLY!
(The Piano DAC 2.1 will only support 2 channel (stereo) left/right output,
pending an update to the upstream pcm512x codec driver, which will have
to be submitted via upstream. With the initial downstream support,
provided by this patch, the Piano DAC 2.1 subwoofer outputs will
not function.)
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net>
Signed-off-by: Clive Messer <clive.messer@digitaldreamtime.co.uk>
Tested-by: Clive Messer <clive.messer@digitaldreamtime.co.uk>
ASoC: allo-piano-dac: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Also remove hw_params and ops as they are no longer needed.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: allo-piano-dac: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add support for Allo Piano DAC 2.1 plus add-on board for Raspberry Pi.
The Piano DAC 2.1 has support for 4 channels with subwoofer.
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net>
Reviewed-by: Vijay Kumar B. <vijaykumar@zilogic.com>
Reviewed-by: Raashid Muhammed <raashidmuhammed@zilogic.com>
Add clock changes and mute gpios (#1938)
Also improve code style and adhere to ALSA coding conventions.
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net>
Reviewed-by: Vijay Kumar B. <vijaykumar@zilogic.com>
Reviewed-by: Raashid Muhammed <raashidmuhammed@zilogic.com>
PianoPlus: Dual Mono & Dual Stereo features added (#2069)
allo-piano-dac-plus: Master volume added + fixes
Master volume added, which controls both DACs volumes.
See: https://github.com/raspberrypi/linux/pull/2149
Also fix initial max volume, default mode value, and unmute.
Signed-off-by: allocom <sparky-dev@allo.com>
ASoC: allo-piano-dac-plus: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Signed-off-by: Matthias Reichl <hias@horus.com>
sound: bcm: Fix memset dereference warning
This warning appears with GCC 6.4.0 from toolchains.bootlin.com:
../sound/soc/bcm/allo-piano-dac-plus.c: In function ‘snd_allo_piano_dac_init’:
../sound/soc/bcm/allo-piano-dac-plus.c:711:30: warning: argument to ‘sizeof’ in ‘memset’ call is the same expression as the destination; did you mean to dereference it? [-Wsizeof-pointer-memaccess]
memset(glb_ptr, 0x00, sizeof(glb_ptr));
^
Suggested-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
ASoC: allo-piano-dac-plus: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add support for Allo Boss DAC add-on board for Raspberry Pi. (#1924)
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net>
Reviewed-by: Deepak <deepak@zilogic.com>
Reviewed-by: BabuSubashChandar <babusubashchandar@zilogic.com>
Add support for new clock rate and mute gpios.
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net>
Reviewed-by: Deepak <deepak@zilogic.com>
Reviewed-by: BabuSubashChandar <babusubashchandar@zilogic.com>
ASoC: allo-boss-dac: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: allo-boss-dac: transmit S24_LE with 64 BCLK cycles
Signed-off-by: Matthias Reichl <hias@horus.com>
allo-boss-dac: switch to snd_soc_dai_set_bclk_ratio
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: allo-boss-dac: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Support for Blokas Labs pisound board
Pisound dynamic overlay (#1760)
Restructuring pisound-overlay.dts, so it can be loaded and unloaded dynamically using dtoverlay.
Print a logline when the kernel module is removed.
pisound improvements:
* Added a writable sysfs object to enable scripts / user space software
to blink MIDI activity LEDs for variable duration.
* Improved hw_param constraints setting.
* Added compatibility with S16_LE sample format.
* Exposed some simple placeholder volume controls, so the card appears
in volumealsa widget.
Add missing SND_PISOUND selects dependency to SND_RAWMIDI
Without it the Pisound module fails to compile.
See https://github.com/raspberrypi/linux/issues/2366
Updates for Pisound module code:
* Merged 'Fix a warning in DEBUG builds' (1c8b82b).
* Updating some strings and copyright information.
* Fix for handling high load of MIDI input and output.
* Use dual rate oversampling ratio for 96kHz instead of single
rate one.
Signed-off-by: Giedrius Trainavicius <giedrius@blokas.io>
Fixing memset call in pisound.c
Signed-off-by: Giedrius Trainavicius <giedrius@blokas.io>
Fix for Pisound's MIDI Input getting blocked for a while in rare cases.
There was a possible race condition which could lead to Input's FIFO queue
to be underflown, causing high amount of processing in the worker thread for
some period of time.
Signed-off-by: Giedrius Trainavicius <giedrius@blokas.io>
Fix for Pisound kernel module in Real Time kernel configuration.
When handler of data_available interrupt is fired, queue_work ends up
getting called and it can block on a spin lock which is not allowed in
interrupt context. The fix was to run the handler from a thread context
instead.
Pisound: Remove spinlock usage around spi_sync
ASoC: pisound: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
ASoC: pisound: fix the parameter for spi_device_match
Signed-off-by: Hui Wang <hui.wang@canonical.com>
ASoC: Add driver for Cirrus Logic Audio Card
Note: due to problems with deferred probing of regulators
the following softdep should be added to a modprobe.d file
softdep arizona-spi pre: arizona-ldo1
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: rpi-cirrus: use modern dai_link style
Signed-off-by: Matthias Reichl <hias@horus.com>
sound: Support for Dion Audio LOCO-V2 DAC-AMP HAT
Signed-off-by: Miquel Blauw <info@dionaudio.nl>
ASoC: dionaudio_loco-v2: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Also remove hw_params and ops as they are no longer needed.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: dionaudio_loco-v2: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add support for Fe-Pi audio sound card. (#1867)
Fe-Pi Audio Sound Card is based on NXP SGTL5000 codec.
Mechanical specification of the board is the same the Raspberry Pi Zero.
3.5mm jacks for Headphone/Mic, Line In, and Line Out.
Signed-off-by: Henry Kupis <fe-pi@cox.net>
ASoC: fe-pi-audio: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add support for the AudioInjector.net Octo sound card
AudioInjector Octo: sample rates, regulators, reset
This patch adds new sample rates to the Audioinjector Octo sound card. The
new supported rates are (in kHz) :
96, 48, 32, 24, 16, 8, 88.2, 44.1, 29.4, 22.05, 14.7
Reference the bcm270x DT regulators in the overlay.
This patch adds a reset GPIO for the AudioInjector.net octo sound card.
Audioinjector octo : Make the playback and capture symmetric
This patch ensures that the sample rate and channel count of the audioinjector
octo sound card are symmetric.
audioinjector-octo: Add continuous clock feature
By user request, add a switch to prevent the clocks being stopped when
the stream is paused, stopped or shutdown. Provide access to the switch
by adding a 'non-stop-clocks' parameter to the audioinjector-addons
overlay.
See: https://github.com/raspberrypi/linux/issues/2409
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
sound: Fixes for audioinjector-octo under 4.19
1. Move the DT alias declaration to the I2C shim in the cases
where the shim is enabled. This works around a problem caused by a
4.19 commit [1] that generates DT/OF uevents for I2C drivers.
2. Fix the diagnostics in an error path of the soundcard driver to
correctly identify the reason for the failure to load.
3. Move the declaration of the clock node in the overlay outside
the I2C node to avoid warnings.
4. Sort the overlay nodes so that dependencies are only to earlier
fragments, in an attempt to get runtime dtoverlay application to
work (it still doesn't...)
See: https://github.com/Audio-Injector/Octo/issues/14
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
[1] af503716ac ("i2c: core: report OF style module alias for devices registered via OF")
ASoC: audioinjector-octo-soundcard: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Driver support for Google voiceHAT soundcard.
ASoC: googlevoicehat-codec: Use correct device when grabbing GPIO
The fixup for the VoiceHAT in 4.18 incorrectly tried to find the
sdmode GPIO pin under the card device, not the codec device.
This failed, and therefore caused the device probe to fail.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
ASoC: googlevoicehat-codec: Reformat for kernel coding standards
Fix all whitespace, indentation, and bracing errors.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
ASoC: googlevoicehat-codec: Make driver function structure const
Make voicehat_component_driver a const structure.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
ASoC: googlevoicehat-codec: Only convert from ms to jiffies once
Minor optimisation and allows to become checkpatch clean.
A msec value is read out of DT or from a define, and convert once to
jiffies, rather than every time that it is used.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Driver and overlay for Allo Katana DAC
Allo Katana DAC: Updated default values
Signed-off-by: Jaikumar <jaikumar@cem-solutions.com>
Added mute stream func
Signed-off-by: Jaikumar <jaikumar@cem-solutions.net>
codecs: Correct Katana minimum volume
Update Katana minimum volume to get the exact 0.5 dB value in each step.
Signed-off-by: Sudeep Kumar <sudeepkumar@cem-solutions.net>
ASoC: Add generic RPI driver for simple soundcards.
The RPI simple sound card driver provides a generic ALSA SOC card driver
supporting a variety of Pi HAT soundcards. The intention is to avoid
the duplication of code for cards that can't be fully supported by
the soc simple/graph cards but are otherwise almost identical.
This initial commit adds support for the ADAU1977 ADC, Google VoiceHat,
HifiBerry AMP, HifiBerry DAC and RPI DAC.
Signed-off-by: Tim Gover <tim.gover@raspberrypi.org>
ASoC: Use correct card name in rpi-simple driver
Use the specific card name from drvdata instead of the snd_rpi_simple
rpi-simple-soundcard: Use nicer driver name "RPi-simple"
Rename the driver from "RPI simple soundcard" to "RPi-simple" so that
the driver name won't be mangled allowing to be used unaltered as the
card conf filename.
ASoC: rpi-simple-soundcard: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
ASoC: Add Kconfig and Makefile for sound/soc/bcm
Signed-off-by: popcornmix <popcornmix@gmail.com>
ASoC: Create a generic Pi Hat WM8804 driver
Reduce the amount of duplicated code by creating a generic driver for
Pi Hat digi cards using the WM8804 codec.
This replaces the
Allo DigiOne, Hifiberry Digi/Pro, JustBoom Digi and IQAudIO Digi
dedicate soundcard drivers with a generic driver.
There are no significant changes to the runtime behavior of the drivers
and end users should not have to change any configuration settings
after upgrading.
Minor changes
* Check the return value of snd_soc_component_update_bits
* Added some pr_debug tracing
* Various checkpatch tidyups
* Updated allodigi-one to use use 128FS at > 96 Khz. This appears to
be an omission in the original driver code so followed the Hifiberry
DAC driver approach.
ASoC: rpi-wm8804-soundcard: use modern dai_link style
Signed-off-by: Matthias Reichl <hias@horus.com>
rpi-wm8804-soundcard: drop PWRDN register writes
Since kernel 4.0 the PWRDN register bits are under DAPM
control from the wm8804 driver.
Drop code that modifies that register to avoid interfering
with DAPM.
Signed-off-by: Matthias Reichl <hias@horus.com>
rpi-wm8804-soundcard: configure wm8804 clocks only on rate change
This should avoid clicks when stopping and immediately afterwards
starting a stream with the same samplerate as before.
Signed-off-by: Matthias Reichl <hias@horus.com>
rpi-wm8804-soundcard: Fixed MCLKDIV for Allo Digione
The Allo Digione board wants a fixed MCLKDIV of 256.
See: https://github.com/raspberrypi/linux/issues/3296
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
ASoC: Add support for AudioSense-Pi add-on soundcard
AudioSense-Pi is a RPi HAT based on a TI's TLV320AIC32x4 stereo codec
This hardware provides multiple audio I/O capabilities to the RPi.
The codec connects to the RPi's SoC through the I2S Bus.
The following devices can be connected through a 3.5mm jack
1. Line-In: Plain old audio in from mobile phones, PCs, etc.,
2. Mic-In: Connect a microphone
3. Line-Out: Connect the output to a speaker
4. Headphones: Connect a Headphone w or w/o microphones
Multiple Inputs:
It supports the following combinations
1. Two stereo Line-Inputs and a microphone
2. One stereo Line-Input and two microphones
3. Two stereo Line-Inputs, a microphone and
one mono line-input (with h/w hack)
4. One stereo Line-Input, two microphones and
one mono line-input (with h/w hack)
Multiple Outputs:
Audio output can be routed to the headphones or
speakers (with additional hardware)
Signed-off-by: b-ak <anur.bhargav@gmail.com>
ASoC: audiosense-pi: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Added driver for the HiFiBerry DAC+ ADC (#2694)
Signed-off-by: Daniel Matuschek <daniel@hifiberry.com>
hifiberry_dacplusadc: switch to snd_soc_dai_set_bclk_ratio
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: hifiberry_dacplusadc: fix DAI link setup
The driver only defines a single DAI link and the code that tries
to setup the second (non-existent) DAI link looks wrong - using dmic
as a CPU/platform driver doesn't make any sense.
The DT overlay doesn't define a dmic property, so the code was never
executed (otherwise it would have resulted in a memory corruption).
So drop the offending code to prevent issues if a dmic property
should be added to the DT overlay.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: hifiberry_dacplusadc: use modern dai_link style
Signed-off-by: Matthias Reichl <hias@horus.com>
Audiophonics I-Sabre 9038Q2M DAC driver
Signed-off-by: Audiophonics <contact@audiophonics.fr>
ASoC: i-sabre-q2m: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Added IQaudIO Pi-Codec board support (#2969)
Add support for the IQaudIO Pi-Codec board.
Signed-off-by: Gordon <gordon@iqaudio.com>
Fixed 48k timing issue
ASoC: iqaudio-codec: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
adds the Hifiberry DAC+ADC PRO version
This adds the driver for the DAC+ADC PRO version of the Hifiberry soundcard with software controlled PCM1863 ADC
Signed-off-by: Joerg Schambacher joerg@i2audio.com
Add Hifiberry DAC+DSP soundcard driver (#3224)
Adds the driver for the Hifiberry DAC+DSP. It supports capture and
playback depending on the DSP firmware.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
Allow simultaneous use of JustBoom DAC and Digi
Signed-off-by: Johannes Krude <johannes@krude.de>
Pisound: MIDI communication fixes for scaled down CPU.
* Increased maximum SPI communication speed to avoid running too slow
when the CPU is scaled down and losing MIDI data.
* Keep track of buffer usage in millibytes for higher precision.
Signed-off-by: Giedrius Trainavičius <giedrius@blokas.io>
sound: Add the HiFiBerry DAC+HD version
This adds the driver for the DAC+HD version supporting HiFiBerry's
PCM179x based DACs. It also adds PLL control for clock generation.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
Fix master mode settings of HiFiBerry DAC+ADC PRO card (#3424)
This patch fixes the board DAI setting when in master-mode.
Wrong setting could have caused random pop noise.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
adds LED OFF feature to HiFiBerry DAC+ADC PRO sound card
This adds a DT overlay parameter 'leds_off' which allows
to switch off the onboard activity LEDs at all times
which has been requested by some users.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
adds LED OFF feature to HiFiBerry DAC+ADC sound card
This adds a DT overlay parameter 'leds_off' which allows
to switch off the onboard activity LEDs at all times
which has been requested by some users.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
adds LED OFF feature to HiFiBerry DAC+/DAC+PRO sound cards
This adds a DT overlay parameter 'leds_off' which allows
to switch off the onboard activity LEDs at all times
which has been requested by some users.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
pisound: Added reading Pisound board hardware revision and exposing it (#3425)
pisound: Added reading Pisound board hardware revision and exposing it in kernel log and sysfs file:
/sys/kernel/pisound/hw_version
Signed-off-by: Giedrius <giedrius@blokas.io>
Added driver for HiFiBerry Amp amplifier add-on board
The driver contains a low-level hardware driver for the TAS5713 and the
drivers for the Raspberry Pi I2S subsystem.
TAS5713: return error if initialisation fails
Existing TAS5713 driver logs errors during initialisation, but does not return
an error code. Therefore even if initialisation fails, the driver will still be
loaded, but won't work. This patch fixes this. I2C communication error will now
reported correctly by a non-zero return code.
HiFiBerry Amp: fix device-tree problems
Some code to load the driver based on device-tree-overlays was missing. This is added by this patch.
According to 5713 pdf doc CLOCK_CTRL is a readonly status register, and it behaves so. Remove useless setting
sound: pcm512x-codec: Adding 352.8kHz samplerate support
sound/soc: only first codec is master in multicodec setup
When using multiple codecs, at most one codec should generate the master
clock. All codecs except the first are therefore configured for slave
mode.
Signed-off-by: Johannes Krude <johannes@krude.de>
ASoC: Fix snd_soc_get_pcm_runtime usage
Commit [1] changed the snd_soc_get_pcm_runtime to take a dai_link
pointer instead of a string. Patch up the downstream drivers to use
the modified API.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
[1] 4468189ff3 ("ASoC: soc-core: find rtd via dai_link pointer at snd_soc_get_pcm_runtime()")
Add support for the AudioInjector.net Isolated sound card
This patch adds support for the Audio Injector Isolated sound card.
Signed-off-by: Matt Flax <flatmax@flatmax.org>
Add support for merus-amp soundcard and ma120x0p codec
Add 96KHz rate support to MA120X0P codec and make enable and mute gpio
pins optional.
Signed-off-by: AMuszkat <ariel.muszkat@gmail.com>
Fixes a problem with clock settings of HiFiBerry DAC+ADC PRO (#3545)
This patch fixes a problem of the re-calculation of
i2s-clock and -parameter settings when only the ADC is activated.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
configs: Enable the AD193x codecs
See: https://github.com/raspberrypi/linux/issues/2850
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Switch to snd_soc_dai_set_bclk_ratio
Replaces obsolete function snd_soc_dai_set_tdm_slot
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
Enhances the DAC+ driver to control the optional headphone amplifier
Probes on the I2C bus for TPA6130A2, if successful, it sets DT-parameter
'status' from 'disabled' to 'okay' using change_sets to enable
the headphone control.
Signed-off-by: Joerg Schambacher joerg@i2audio.com
The Raspberry Pi firmware manages the power-down and reboot
process. To do this it installs a pm_power_off handler, causing
the gpio-poweroff module to abort the probe function.
This patch introduces a "force" DT property that overrides that
behaviour, and also adds a DT overlay to enable and control it.
Note that running in an active-low configuration (DT parameter
"active_low") requires a custom dt-blob.bin and probably won't
allow a reboot without switching off, so an external inversion
of the trigger signal may be preferable.
Provide a __copy_from_user that uses memcpy. On BCM2708, use
optimised memcpy/memmove/memcmp/memset implementations.
arch/arm: Add mmiocpy/set aliases for memcpy/set
See: https://github.com/raspberrypi/linux/issues/1082
copy_from_user: CPU_SW_DOMAIN_PAN compatibility
The downstream copy_from_user acceleration must also play nice with
CONFIG_CPU_SW_DOMAIN_PAN.
See: https://github.com/raspberrypi/linux/issues/1381
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Fix copy_from_user if BCM2835_FAST_MEMCPY=n
The change which introduced CONFIG_BCM2835_FAST_MEMCPY unconditionally
changed the behaviour of arm_copy_from_user. The page pinning code
is not safe on ARMv7 if LPAE & high memory is enabled and causes
crashes which look like PTE corruption.
Make __copy_from_user_memcpy conditional on CONFIG_2835_FAST_MEMCPY=y
which is really an ARMv6 / Pi1 optimization and not necessary on newer
ARM processors.
arm: fix mmap unlocks in uaccess_with_memcpy.c
This is a regression that was added with the commit 192a4e923e as of rpi-5.8.y, since that is when the move to the mmap locking API was introduced - d8ed45c5dc
The issue is that when the patch to improve performance for the __copy_to_user and __copy_from_user functions were added for the Raspberry Pi, some of the mmaps were incorrectly mapped to write instead of read. This would cause a verity of issues, and in my case, prevent the booting of a squashfs filesystem on rpi-5.8-y and above. An example of the panic you would see from this can be seen at https://pastebin.com/raw/jBz5xCzL
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Christopher Blake <chrisrblake93@gmail.com>
The "input" trigger makes the associated GPIO an input. This is to support
the Raspberry Pi PWR LED, which is driven by external hardware in normal use.
N.B. pwr_led is not available on Model A or B boards.
leds-gpio: Implement the brightness_get method
The power LED uses some clever logic that means it is driven
by a voltage measuring circuit when configured as input, otherwise
it is driven by the GPIO output value. This patch wires up the
brightness_get method for leds-gpio so that user-space can monitor
the LED value via /sys/class/gpio/led1/brightness. Using the input
trigger this returns an indication of the system power health,
otherwise it is just whatever value the trigger has written most
recently.
See: https://github.com/raspberrypi/linux/issues/1064
Add the bare minimum needed to boot BCM2708 from a Device Tree.
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
BCM2708: DT: change 'axi' nodename to 'soc'
Change DT node named 'axi' to 'soc' so it matches ARCH_BCM2835.
The VC4 bootloader fills in certain properties in the 'axi' subtree,
but since this is part of an upstreaming effort, the name is changed.
Signed-off-by: Noralf Tronnes notro@tronnes.org
BCM2708_DT: Correct length of the peripheral space
Use dts-dirs feature for overlays.
The kernel makefiles have a dts-dirs target that is for vendor subdirectories.
Using this fixes the install_dtbs target, which previously did not install the overlays.
BCM270X_DT: configure I2S DMA channels
Signed-off-by: Matthias Reichl <hias@horus.com>
BCM270X_DT: switch to bcm2835-i2s
I2S soundcard drivers with proper devicetree support (i.e. not linking
to the cpu_dai/platform via name but to cpu/platform via of_node)
will work out of the box without any modifications.
When the kernel is compiled without devicetree support the platform
code will instantiate the bcm2708-i2s driver and I2S soundcard drivers
will link to it via name, as before.
Signed-off-by: Matthias Reichl <hias@horus.com>
SDIO-overlay: add poll_once-boolean parameter
Add paramter to toggle sdio-device-polling
done every second or once at boot-time.
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
BCM270X_DT: Make mmc overlay compatible with current firmware
The original DT overlay logic followed a merge-then-patch procedure,
i.e. parameters are applied to the loaded overlay before the overlay
is merged into the base DTB. This sequence has been changed to
patch-then-merge, in order to support parameterised node names, and
to protect against bad overlays. As a result, overrides (parameters)
must only target labels in the overlay, but the overlay can obviously target nodes in the base DTB.
mmc-overlay.dts (that switches back to the original mmc sdcard
driver) is the only overlay violating that rule, and this patch
fixes it.
bcm270x_dt: Use the sdhost MMC controller by default
The "mmc" overlay reverts to using the other controller.
squash: Add cprman to dt
BCM270X_DT: Use clk_core for I2C interfaces
BCM270X_DT: Use bcm283x.dtsi, bcm2835.dtsi and bcm2836.dtsi
The mainline Device Tree files are quite close to downstream now.
Let's use bcm283x.dtsi, bcm2835.dtsi and bcm2836.dtsi as base files
for our dts files.
Mainline dts files are based on these files:
bcm2835-rpi.dtsi
bcm2835.dtsi bcm2836.dtsi
bcm283x.dtsi
Current downstream are based on these:
bcm2708.dtsi bcm2709.dtsi bcm2710.dtsi
bcm2708_common.dtsi
This patch introduces this dependency:
bcm2708.dtsi bcm2709.dtsi
bcm2708-rpi.dtsi
bcm270x.dtsi
bcm2835.dtsi bcm2836.dtsi
bcm283x.dtsi
And:
bcm2710.dtsi
bcm2708-rpi.dtsi
bcm270x.dtsi
bcm283x.dtsi
bcm270x.dtsi contains the downstream bcm283x.dtsi diff.
bcm2708-rpi.dtsi is the downstream version of bcm2835-rpi.dtsi.
Other changes:
- The led node has moved from /soc/leds to /leds. This is not a problem
since the label is used to reference it.
- The clk_osc reg property changes from 6 to 3.
- The gpu nodes has their interrupt property set in the base file.
- the clocks label does not point to the /clocks node anymore, but
points to the cprman node. This is not a problem since the overlays
that use the clock node refer to it directly: target-path = "/clocks";
- some nodes now have 2 labels since mainline and downstream differs in
this respect: cprman/clocks, spi0/spi, gpu/vc4.
- some nodes doesn't have an explicit status = "okay" since they're not
disabled in the base file: watchdog and random.
- gpiomem doesn't need an explicit status = "okay".
- bcm2708-rpi-cm.dts got the hpd-gpios property from bcm2708_common.dtsi,
it's now set directly in that file.
- bcm2709-rpi-2-b.dts has the timer node moved from /soc/timer to /timer.
- Removed clock-frequency property on the bcm{2709,2710}.dtsi timer nodes.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270X_DT: Use raspberrypi-power to turn on USB power
Use the raspberrypi-power driver to turn on USB power.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270X_DT: Add a .dtbo target, use for overlays
Change the filenames and extensions to keep the pre-DDT style of
overlay (<name>-overlay.dtb) distinct from new ones that use a
different style of local fixups (<name>.dtbo), and to match other
platforms.
The RPi firmware uses the DDTK trailer atom to choose which type of
overlay to use for each kernel.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: Don't generate "linux,phandle" props
The EPAPR standard says to use "phandle" properties to store phandles,
rather than the deprecated "linux,phandle" version. By default, dtc
generates both, but adding "-H epapr" causes it to only generate
"phandle"s, saving some space and clutter.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: Add overlay for enc28j60 on SPI2
Works on SPI2 for compute module
BCM270X_DT: Add midi-uart0 overlay
MIDI requires 31.25kbaud, a baudrate unsupported by Linux. The
midi-uart0 overlay configures uart0 (ttyAMA0) to use a fake clock
so that requesting 38.4kbaud actually gets 31.25kbaud.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: Add i2c-sensor overlay
The i2c-sensor overlay is a container for various pressure and
temperature sensors, currently bmp085 and bmp280. The standalone
bmp085_i2c-sensor overlay is now deprecated.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: overlays/*-overlay.dtb -> overlays/*.dtbo (#1752)
We now create overlays as .dtbo files.
build: support for .dtbo files for dtb overlays
Kernel 4.4.6+ on RaspberryPi support .dtbo files for overlays, instead of .dtb.
Patch the kernel, which has faulty rules to generate .dtbo the way yocto does
Signed-off-by: Herve Jourdain <herve.jourdain@neuf.fr>
Signed-off-by: Khem Raj <raj.khem@gmail.com>
BCM270X: Drop position requirement for CMA in VC4 overlay.
No longer necessary since 2aefcd5761,
and will probably let peeople that want to choose a larger CMA
allocation (particularly on pi0/1).
Signed-off-by: Eric Anholt <eric@anholt.net>
BCM270X_DT: RPi Device Tree tidy
Use the upstream sdhost node, add thermal-zones, and factor out some
common elements.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
kbuild: Silence unhelpful DTC warnings
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: DT build rules no longer arch-specific
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Support booting without Device Tree.
Turn on USB power.
Load driver early because of lacking support for deferred probing
in many drivers.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
firmware: bcm2835: Don't turn on USB power
The raspberrypi-power driver is now used to turn on USB power.
This partly reverts commit:
firmware: bcm2835: Support ARCH_BCM270x
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Add module for accessing the mailbox property channel through
/dev/vcio. Was previously in bcm2708-vcio.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
char: vcio: Add compat ioctl handling
There was no compat ioctl handler, so 32 bit userspace on a
64 bit kernel failed as IOCTL_MBOX_PROPERTY used the size
of char*.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
char: vcio: Fail probe if rpi_firmware is not found.
Device Tree is now the only supported config mechanism, therefore
uncomment the block of code that fails the probe if the
firmware node can't be found.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
i2c-bcm2708: fixed baudrate
Fixed issue where the wrong CDIV value was set for baudrates below 3815 Hz (for 250MHz bus clock).
In that case the computed CDIV value was more than 0xffff. However the CDIV register width is only 16 bits.
This resulted in incorrect setting of CDIV and higher baudrate than intended.
Example: 3500Hz -> CDIV=0x11704 -> CDIV(16bit)=0x1704 -> 42430Hz
After correction: 3500Hz -> CDIV=0x11704 -> CDIV(16bit)=0xffff -> 3815Hz
The correct baudrate is shown in the log after the cdiv > 0xffff correction.
Perform I2C combined transactions when possible
Perform I2C combined transactions whenever possible, within the
restrictions of the Broadcomm Serial Controller.
Disable DONE interrupt during TA poll
Prevent interrupt from being triggered if poll is missed and transfer
starts and finishes.
i2c: Make combined transactions optional and disabled by default
i2c: bcm2708: add device tree support
Add DT support to driver and add to .dtsi file.
Setup pins in .dts file.
i2c is disabled by default.
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
bcm2708: don't register i2c controllers when using DT
The devices for the i2c controllers are in the Device Tree.
Only register devices when not using DT.
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
I2C: Only register the I2C device for the current board revision
i2c_bcm2708: Fix clock reference counting
Fix grabbing lock from atomic context in i2c driver
2 main changes:
- check for timeouts in the bcm2708_bsc_setup function as indicated by this comment:
/* poll for transfer start bit (should only take 1-20 polls) */
This implies that the setup function can now fail so account for this everywhere it's called
- Removed the clk_get_rate call from inside the setup function as it locks a mutex and that's not ok since we call it from under a spin lock.
i2c-bcm2708: When using DT, leave the GPIO setup to pinctrl
i2c-bcm2708: Increase timeouts to allow larger transfers
Use the timeout value provided by the I2C_TIMEOUT ioctl when waiting
for completion. The default timeout is 1 second.
See: https://github.com/raspberrypi/linux/issues/260
i2c-bcm2708/BCM270X_DT: Add support for I2C2
The third I2C bus (I2C2) is normally reserved for HDMI use. Careless
use of this bus can break an attached display - use with caution.
It is recommended to disable accesses by VideoCore by setting
hdmi_ignore_edid=1 or hdmi_edid_file=1 in config.txt.
The interface is disabled by default - enable using the
i2c2_iknowwhatimdoing DT parameter.
bcm2708-spi: Don't use static pin configuration with DT
Also remove superfluous error checking - the SPI framework ensures the
validity of the chip_select value.
i2c-bcm2708: Remove non-DT support
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Set the BSC_CLKT clock streching timeout to 35ms as per SMBus specs.
Fixes i2c_bcm2708: Write to FIFO correctly - v2 (#1574)
* i2c: fix i2c_bcm2708: Clear FIFO before sending data
Make sure FIFO gets cleared before trying to send
data in case of a repeated start (COMBINED=Y).
* i2c: fix i2c_bcm2708: Only write to FIFO when not full
Check if FIFO can accept data before writing.
To avoid a peripheral read on the last iteration of a loop,
both bcm2708_bsc_fifo_fill and ~drain are changed as well.
Signed-off-by: Luke Wren <wren6991@gmail.com>
MISC: bcm2835: smi: use clock manager and fix reload issues
Use clock manager instead of self-made clockmanager.
Also fix some error paths that showd up during development
(especially missing release of dma resources on rmmod)
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
bcm2835_smi: re-add dereference to fix DMA transfers
Signed-off-by: popcornmix <popcornmix@gmail.com>
BCM270x: Move vc_mem
Make the vc_mem module available for ARCH_BCM2835 by moving it.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
char: vc_mem: Fix up compat ioctls for 64bit kernel
compat_ioctl wasn't defined, so 32bit user/64bit kernel
always failed.
VC_MEM_IOC_MEM_PHYS_ADDR was defined with parameter size
unsigned long, so the ioctl cmd changes between sizes.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
char: vc_mem: Fix all coding style issues.
Cleans up all checkpatch errors in vc_mem.c and vc_mem.h
No functional change to the code.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
BCM2835 has two SD card interfaces. This driver uses the other one.
bcm2835-sdhost: Error handling fix, and code clarification
bcm2835-sdhost: Adding overclocking option
Allow a different clock speed to be substitued for a requested 50MHz.
This option is exposed using the "overclock_50" DT parameter.
Note that the sdhost interface is restricted to integer divisions of
core_freq, and the highest sensible option for a core_freq of 250MHz
is 84 (250/3 = 83.3MHz), the next being 125 (250/2) which is much too
high.
Use at your own risk.
bcm2835-sdhost: Round up the overclock, so 62 works for 62.5Mhz
Also only warn once for each overclock setting.
bcm2835-sdhost: Improve error handling and recovery
1) Expose the hw_reset method to the MMC framework, removing many
internal calls by the driver.
2) Reduce overclock setting on error.
3) Increase timeout to cope with high capacity cards.
4) Add properties and parameters to control pio_limit and debug.
5) Reduce messages at probe time.
bcm2835-sdhost: Further improve overclock back-off
bcm2835-sdhost: Clear HBLC for PIO mode
Also update pio_limit default in overlay README.
bcm2835-sdhost: Add the ERASE capability
See: https://github.com/raspberrypi/linux/issues/1076
bcm2835-sdhost: Ignore CRC7 for MMC CMD1
It seems that the sdhost interface returns CRC7 errors for CMD1,
which is the MMC-specific SEND_OP_COND. Returning these errors to
the MMC layer causes a downward spiral, but ignoring them seems
to be harmless.
bcm2835-mmc/sdhost: Remove ARCH_BCM2835 differences
The bcm2835-mmc driver (and -sdhost driver that copied from it)
contains code to handle SDIO interrupts in a threaded interrupt
handler rather than waking the MMC framework thread. The change
follows a patch from Russell King that adds the facility as the
preferred way of working.
However, the new code path is only present in ARCH_BCM2835
builds, which I have taken to be a way of testing the waters
rather than making the change across the board; I can't see
any technical reason why it wouldn't be enabled for MACH_BCM270X
builds. So this patch standardises on the ARCH_BCM2835 code,
removing the old code paths.
bcm2835-sdhost: Don't log timeout errors unless debug=1
The MMC card-discovery process generates timeouts. This is
expected behaviour, so reporting it to the user serves no purpose.
Suppress the reporting of timeout errors unless the debug flag
is on.
bcm2835-sdhost: Add workaround for odd behaviour on some cards
For reasons not understood, the sdhost driver fails when reading
sectors very near the end of some SD cards. The problem could
be related to the similar issue that reading the final sector
of any card as part of a multiple read never completes, and the
workaround is an extension of the mechanism introduced to solve
that problem which ensures those sectors are always read singly.
bcm2835-sdhost: Major revision
This is a significant revision of the bcm2835-sdhost driver. It
improves on the original in a number of ways:
1) Through the use of CMD23 for reads it appears to avoid problems
reading some sectors on certain high speed cards.
2) Better atomicity to prevent crashes.
3) Higher performance.
4) Activity logging included, for easier diagnosis in the event
of a problem.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Restore ATOMIC flag to PIO sg mapping
Allocation problems have been seen in a wireless driver, and
this is the only change which might have been responsible.
SQUASH: bcm2835-sdhost: Only claim one DMA channel
With both MMC controllers enabled there are few DMA channels left. The
bcm2835-sdhost driver only uses DMA in one direction at a time, so it
doesn't need to claim two channels.
See: https://github.com/raspberrypi/linux/issues/1327
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Workaround for "slow" sectors
Some cards have been seen to cause timeouts after certain sectors are
read. This workaround enforces a minimum delay between the stop after
reading one of those sectors and a subsequent data command.
Using CMD23 (SET_BLOCK_COUNT) avoids this problem, so good cards will
not be penalised by this workaround.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Firmware manages the clock divisor
The bcm2835-sdhost driver hands control of the CDIV clock divisor
register to matching firmware, allowing it to adjust to a changing
core clock. This removes the need to use the performance governor or
to enable io_is_busy on the on-demand governor in order to get the
best SD performance.
N.B. As SD clocks must be an integer divisor of the core clock, it is
possible that the SD clock for "turbo" mode can be different (even
lower) than "normal" mode.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Reset the clock in task context
Since reprogramming the clock can now involve a round-trip to the
firmware it must not be done at atomic context, and a tasklet
is not a task.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Don't exit cmd wait loop on error
The FAIL flag can be set in the CMD register before command processing
is complete, leading to spurious "failed to complete" errors. This has
the effect of promoting harmless CRC7 errors during CMD1 processing
into errors that can delay and even prevent booting.
Also:
1) Convert the last KERN_ERROR message in the register dumping to
KERN_INFO.
2) Remove an unnecessary reset call from bcm2835_sdhost_add_host.
See: https://github.com/raspberrypi/linux/pull/1492
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: mmc_card_blockaddr fix
Get the definition of mmc_card_blockaddr from drivers/mmc/core/card.h.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: New timer API
mmc: bcm2835-sdhost: Support underclocking
Support underclocking of the SD bus in two ways:
1. using the max-frequency DT property (which currently has no DT
parameter), and
2. using the exiting sd_overclock parameter.
The two methods differ slightly - in the former the MMC subsystem is
aware of the underclocking, while in the latter it isn't - but the
end results should be the same.
See: https://github.com/raspberrypi/linux/issues/2350
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
mmc: bcm2835-sdhost: Add include
highmem.h (needed for kmap_atomic) is pulled in by one of the other
include files, but only with some CONFIG settings. Make the inclusion
explicit to cater for cases where the CONFIG setting is absent.
See: https://github.com/raspberrypi/linux/issues/2366
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
mmc/bcm2835-sdhost: Recover from MMC_SEND_EXT_CSD
If the user issues an "mmc extcsd read", the SD controller receives
what it thinks is a SEND_IF_COND command with an unexpected data block.
The resulting operations leave the FSM stuck in READWAIT, a state which
persists until the MMC framework resets the controller, by which point
the root filesystem is likely to have been unmounted.
A less heavyweight solution is to detect the condition and nudge the
FSM by asserting the (self-clearing) FORCE_DATA_MODE bit.
N.B. This workaround was essentially discovered by accident and without
a full understanding the inner workings of the controller, so it is
fortunate that the "fix" only modifies error paths.
See: https://github.com/raspberrypi/linux/issues/2728
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
mmc: bcm2835-sdhost: Fix warnings on arm64
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Allow for sg entries that cross pages
The dma_complete handling code calculates a virtual address for a page
then adds an offset, but if the offset is more than a page and HIGHMEM
is in use then the summed address could be in an unmapped (or just
incorrect) page.
The upstream SDHOST driver allows for this possibility - copy the code
that does so.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Fix DMA channel leak on error/remove
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
mmc: bcm2835-sdhost: Support 64-bit physical addresses
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Replace obsolete struct timeval
struct timeval has been retired due to the impending linux 32-bit tv_sec
rollover (only 18 years to go) - timespec64 is the obvious replacement.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
mmc: Disable CMD23 transfers on all cards
Pending wire-level investigation of these types of transfers
and associated errors on bcm2835-mmc, disable for now. Fallback of
CMD18/CMD25 transfers will be used automatically by the MMC layer.
Reported/Tested-by: Gellert Weisz <gellert@raspberrypi.org>
mmc: bcm2835-mmc: enable DT support for all architectures
Both ARCH_BCM2835 and ARCH_BCM270x are built with OF now.
Enable Device Tree support for all architectures.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
mmc: bcm2835-mmc: fix probe error handling
Probe error handling is broken in several places.
Simplify error handling by using device managed functions.
Replace pr_{err,info} with dev_{err,info}.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2835-mmc: Add locks when accessing sdhost registers
bcm2835-mmc: Add range of debug options for slowing things down
bcm2835-mmc: Add option to disable some delays
bcm2835-mmc: Add option to disable MMC_QUIRK_BLK_NO_CMD23
bcm2835-mmc: Default to disabling MMC_QUIRK_BLK_NO_CMD23
bcm2835-mmc: Adding overclocking option
Allow a different clock speed to be substitued for a requested 50MHz.
This option is exposed using the "overclock_50" DT parameter.
Note that the mmc interface is restricted to EVEN integer divisions of
250MHz, and the highest sensible option is 63 (250/4 = 62.5), the
next being 125 (250/2) which is much too high.
Use at your own risk.
bcm2835-mmc: Round up the overclock, so 62 works for 62.5Mhz
Also only warn once for each overclock setting.
mmc: bcm2835-mmc: Make available on ARCH_BCM2835
Make the bcm2835-mmc driver available for use on ARCH_BCM2835.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270x_DT: add bcm2835-mmc entry
Add Device Tree entry for bcm2835-mmc.
In non-DT mode, don't add the device in the board file.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2835-mmc: Don't overwrite MMC capabilities from DT
bcm2835-mmc: Don't override bus width capabilities from devicetree
Take out the force setting of the MMC_CAP_4_BIT_DATA host capability
so that the result read from devicetree via mmc_of_parse() is
preserved.
bcm2835-mmc: Only claim one DMA channel
With both MMC controllers enabled there are few DMA channels left. The
bcm2835-mmc driver only uses DMA in one direction at a time, so it
doesn't need to claim two channels.
See: https://github.com/raspberrypi/linux/issues/1327
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-mmc: New timer API
mmc: bcm2835-mmc: Support underclocking
Support underclocking of the SD bus using the max-frequency DT property
(which currently has no DT parameter). The sd_overclock parameter
already provides another way to achieve the same thing which should be
equivalent in end result, but it is a bug not to support max-frequency
as well.
See: https://github.com/raspberrypi/linux/issues/2350
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
mmc/bcm2835: Recover from MMC_SEND_EXT_CSD
If the user issues an "mmc extcsd read", the SD controller receives
what it thinks is a SEND_IF_COND command with an unexpected data block.
The resulting operations leave the FSM stuck in READWAIT, a state which
persists until the MMC framework resets the controller, by which point
the root filesystem is likely to have been unmounted.
A less heavyweight solution is to detect the condition and nudge the
FSM by asserting the (self-clearing) FORCE_DATA_MODE bit.
N.B. This workaround was essentially discovered by accident and without
a full understanding the inner workings of the controller, so it is
fortunate that the "fix" only modifies error paths.
See: https://github.com/raspberrypi/linux/issues/2728
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-mmc: Fix DMA channel leak
The BCM2835 MMC host driver requests a DMA channel on probe but neglects
to release the channel in the probe error path and on driver unbind.
I'm seeing this happen on every boot of the Compute Module 3: On first
driver probe, DMA channel 2 is allocated and then leaked with a "could
not get clk, deferring probe" message. On second driver probe, channel 4
is allocated.
Fix it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
bcm2835-mmc: Fix struct mmc_host leak on probe
The BCM2835 MMC host driver requests the bus address of the host's
register map on probe. If that fails, the driver leaks the struct
mmc_host allocated earlier.
Fix it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
bcm2835-mmc: Fix duplicate free_irq() on remove
The BCM2835 MMC host driver requests its interrupt as a device-managed
resource, so the interrupt is automatically freed after the driver is
unbound.
However on driver unbind, bcm2835_mmc_remove() frees the interrupt
explicitly to avoid invocation of the interrupt handler after driver
structures have been torn down.
The interrupt is thus freed twice, leading to a WARN splat in
__free_irq(). Fix by not requesting the interrupt as a device-managed
resource.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
bcm2835-mmc: Handle mmc_add_host() errors
The BCM2835 MMC host driver calls mmc_add_host() but doesn't check its
return value. Errors occurring in that function are therefore not
handled. Fix it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
bcm2835-mmc: Deduplicate reset of driver data on remove
The BCM2835 MMC host driver sets the device's driver data pointer to
NULL on ->remove() even though the driver core subsequently does the
same in __device_release_driver(). Drop the duplicate assignment.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
bcm2835_mmc: Remove vestigial threaded IRQ
With SDIO processing now managed by the MMC framework with a
workqueue, the bcm2835_mmc driver no longer needs a threaded
IRQ.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Add missing dma_unmap_sg calls to free relevant swiotlb bounce buffers.
This prevents DMA leaks.
Signed-off-by: Yaroslav Rosomakho <yaroslavros@gmail.com>
Limit max_req_size under arm64 (or any other platform that uses swiotlb) to prevent potential buffer overflow due to bouncing.
Signed-off-by: Yaroslav Rosomakho <yaroslavros@gmail.com>
Add support for DMA controller of BCM2708 as used in the Raspberry Pi.
Currently it only supports cyclic DMA.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
dmaengine: expand functionality by supporting scatter/gather transfers sdhci-bcm2708 and dma.c: fix for LITE channels
DMA: fix cyclic LITE length overflow bug
dmaengine: bcm2708: Remove chancnt affectations
Mirror bcm2835-dma.c commit 9eba5536a7:
chancnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: overwrite dreq only if it is not set
dreq is set when the DMA channel is fetched from Device Tree.
slave_id is set using dmaengine_slave_config().
Only overwrite dreq with slave_id if it is not set.
dreq/slave_id in the cyclic DMA case is not touched, because I don't
have hardware to test with.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: do device registration in the board file
Don't register the device in the driver. Do it in the board file.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: don't restrict DT support to ARCH_BCM2835
Both ARCH_BCM2835 and ARCH_BCM270x are built with OF now.
Add Device Tree support to the non ARCH_BCM2835 case.
Use the same driver name regardless of architecture.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270x_DT: add bcm2835-dma entry
Add Device Tree entry for bcm2835-dma.
The entry doesn't contain any resources since they are handled
by the arch/arm/mach-bcm270x/dma.c driver.
In non-DT mode, don't add the device in the board file.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2708-dmaengine: Add debug options
BCM270x: Add memory and irq resources to dmaengine device and DT
Prepare for merging of the legacy DMA API arch driver dma.c
with bcm2708-dmaengine by adding memory and irq resources both
to platform file device and Device Tree node.
Don't use BCM_DMAMAN_DRIVER_NAME so we don't have to include mach/dma.h
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: Merge with arch dma.c driver and disable dma.c
Merge the legacy DMA API driver with bcm2708-dmaengine.
This is done so we can use bcm2708_fb on ARCH_BCM2835 (mailbox
driver is also needed).
Changes to the dma.c code:
- Use BIT() macro.
- Cutdown some comments to one line.
- Add mutex to vc_dmaman and use this, since the dev lock is locked
during probing of the engine part.
- Add global g_dmaman variable since drvdata is used by the engine part.
- Restructure for readability:
vc_dmaman_chan_alloc()
vc_dmaman_chan_free()
bcm_dma_chan_free()
- Restructure bcm_dma_chan_alloc() to simplify error handling.
- Use device irq resources instead of hardcoded bcm_dma_irqs table.
- Remove dev_dmaman_register() and code it directly.
- Remove dev_dmaman_deregister() and code it directly.
- Simplify bcm_dmaman_probe() using devm_* functions.
- Get dmachans from DT if available.
- Keep 'dma.dmachans' module argument name for backwards compatibility.
Make it available on ARCH_BCM2835 as well.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: set residue_granularity field
bcm2708-dmaengine supports residue reporting at burst level
but didn't report this via the residue_granularity field.
Without this field set properly we get playback issues with I2S cards.
dmaengine: bcm2708-dmaengine: Fix memory leak when stopping a running transfer
bcm2708-dmaengine: Use more DMA channels (but not 12)
1) Only the bcm2708_fb drivers uses the legacy DMA API, and
it requires a BULK-capable channel, so all other types
(FAST, NORMAL and LITE) can be made available to the regular
DMA API.
2) DMA channels 11-14 share an interrupt. The driver can't
handle this, so don't use channels 12-14 (12 was used, probably
because it appears to have an interrupt, but in reality that
interrupt is for activity on ANY channel). This may explain
a lockup encountered when running out of DMA channels.
The combined effect of this patch is to leave 7 DMA channels
available + channel 0 for bcm2708_fb via the legacy API.
See: https://github.com/raspberrypi/linux/issues/1110https://github.com/raspberrypi/linux/issues/1108
dmaengine: bcm2708: Make legacy API available for bcm2835-dma
bcm2708_fb uses the legacy DMA API, so in order to start using
bcm2835-dma, bcm2835-dma has to support the legacy API. Make this
possible by exporting bcm_dmaman_probe() and bcm_dmaman_remove().
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: Change DT compatible string
Both bcm2835-dma and bcm2708-dmaengine have the same compatible string.
So change compatible to "brcm,bcm2708-dma".
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: Remove driver but keep legacy API
Dropping non-DT support means we don't need this driver,
but we still need the legacy DMA API.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2708-dmaengine - Fix arm64 portability/build issues
dma-bcm2708: Fix module compilation of CONFIG_DMA_BCM2708
bcm2708-dmaengine.c defines functions like bcm_dma_start which are
defined as well in dma-bcm2708.h as inline versions when
CONFIG_DMA_BCM2708 is not defined. This works fine when
CONFIG_DMA_BCM2708 is built in, but when it is selected as module build
fails with redefinition errors because in the build system when
CONFIG_DMA_BCM2708 is selected as module, the macro becomes
CONFIG_DMA_BCM2708_MODULE.
This patch makes the header use CONFIG_DMA_BCM2708_MODULE too when
available.
Fixes https://github.com/raspberrypi/linux/issues/2056
Signed-off-by: Andrei Gherzan <andrei@gherzan.com>
Especially on platforms with a slower CPU but a relatively high
framebuffer fill bandwidth, like current ARM devices, the existing
console monochrome imageblit function used to draw console text is
suboptimal for common pixel depths such as 16bpp and 32bpp. The existing
code is quite general and can deal with several pixel depths. By creating
special case functions for 16bpp and 32bpp, by far the most common pixel
formats used on modern systems, a significant speed-up is attained
which can be readily felt on ARM-based devices like the Raspberry Pi
and the Allwinner platform, but should help any platform using the
fb layer.
The special case functions allow constant folding, eliminating a number
of instructions including divide operations, and allow the use of an
unrolled loop, eliminating instructions with a variable shift size,
reducing source memory access instructions, and eliminating excessive
branching. These unrolled loops also allow much better code optimization
by the C compiler. The code that selects which optimized variant is used
is also simplified, eliminating integer divide instructions.
The speed-up, measured by timing 'cat file.txt' in the console, varies
between 40% and 70%, when testing on the Raspberry Pi and Allwinner
ARM-based platforms, depending on font size and the pixel depth, with
the greater benefit for 32bpp.
Signed-off-by: Harm Hanemaaijer <fgenfb@yahoo.com>
Based on the patch authored by Ali Gholami Rudi at
https://lkml.org/lkml/2009/7/13/153
Provide an ioctl for userspace applications, but only if this operation
is hardware accelerated (otherwide it does not make any sense).
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
bcm2708_fb: Add ioctl for reading gpu memory through dma
video: bcm2708_fb: Add compat_ioctl support.
When using a 64 bit kernel with 32 bit userspace we need
compat ioctl handling for FBIODMACOPY as one of the
parameters is a pointer.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: popcornmix <popcornmix@gmail.com>
bcm2708_fb : Implement blanking support using the mailbox property interface
bcm2708_fb: Add pan and vsync controls
bcm2708_fb: DMA acceleration for fb_copyarea
Based on http://www.raspberrypi.org/phpBB3/viewtopic.php?p=62425#p62425
Also used Simon's dmaer_master module as a reference for tweaking DMA
settings for better performance.
For now busylooping only. IRQ support might be added later.
With non-overclocked Raspberry Pi, the performance is ~360 MB/s
for simple copy or ~260 MB/s for two-pass copy (used when dragging
windows to the right).
In the case of using DMA channel 0, the performance improves
to ~440 MB/s.
For comparison, VFP optimized CPU copy can only do ~114 MB/s in
the same conditions (hindered by reading uncached source buffer).
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
bcm2708_fb: report number of dma copies
Add a counter (exported via debugfs) reporting the
number of dma copies that the framebuffer driver
has done, in order to help evaluate different
optimization strategies.
Signed-off-by: Luke Diamand <luked@broadcom.com>
bcm2708_fb: use IRQ for DMA copies
The copyarea ioctl() uses DMA to speed things along. This
was busy-waiting for completion. This change supports using
an interrupt instead for larger transfers. For small
transfers, busy-waiting is still likely to be faster.
Signed-off-by: Luke Diamand <luke@diamand.org>
bcm2708: Make ioctl logging quieter
video: fbdev: bcm2708_fb: Don't panic on error
No need to panic the kernel if the video driver fails.
Just print a message and return an error.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
fbdev: bcm2708_fb: Add ARCH_BCM2835 support
Add Device Tree support.
Pass the device to dma_alloc_coherent() in order to get the
correct bus address on ARCH_BCM2835.
Use the new DMA legacy API header file.
Including <mach/platform.h> is not necessary.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270x_DT: Add bcm2708-fb device
Add bcm2708-fb to Device Tree and don't add the
platform device when booting in DT mode.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Cleanup of bcm2708_fb file to kernel coding standards
Some minor change to function - remove a use of
in_atomic, plus replacing various debug messages
that manually specify the function name with
("%s",.__func__)
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
video: bcm2708_fb: Try allocating on the ARM and passing to VPU
Currently the VPU allocates the contiguous buffer for the
framebuffer.
Try an alternate path first where we use dma_alloc_coherent
and pass the buffer to the VPU. Should the VPU firmware not
support that path, then free the buffer and revert to the
old behaviour of using the VPU allocation.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: popcornmix <popcornmix@gmail.com>
usb: dwc: fix lockdep false positive
Signed-off-by: Kari Suvanto <karis79@gmail.com>
usb: dwc: fix inconsistent lock state
Signed-off-by: Kari Suvanto <karis79@gmail.com>
Add FIQ patch to dwc_otg driver. Enable with dwc_otg.fiq_fix_enable=1. Should give about 10% more ARM performance.
Thanks to Gordon and Costas
Avoid dynamic memory allocation for channel lock in USB driver. Thanks ddv2005.
Add NAK holdoff scheme. Enabled by default, disable with dwc_otg.nak_holdoff_enable=0. Thanks gsh
Make sure we wait for the reset to finish
dwc_otg: fix bug in dwc_otg_hcd.c resulting in silent kernel
memory corruption, escalating to OOPS under high USB load.
dwc_otg: Fix unsafe access of QTD during URB enqueue
In dwc_otg_hcd_urb_enqueue during qtd creation, it was possible that the
transaction could complete almost immediately after the qtd was assigned
to a host channel during URB enqueue, which meant the qtd pointer was no
longer valid having been completed and removed. Usually, this resulted in
an OOPS during URB submission. By predetermining whether transactions
need to be queued or not, this unsafe pointer access is avoided.
This bug was only evident on the Pi model A where a device was attached
that had no periodic endpoints (e.g. USB pendrive or some wlan devices).
dwc_otg: Fix incorrect URB allocation error handling
If the memory allocation for a dwc_otg_urb failed, the kernel would OOPS
because for some reason a member of the *unallocated* struct was set to
zero. Error handling changed to fail correctly.
dwc_otg: fix potential use-after-free case in interrupt handler
If a transaction had previously aborted, certain interrupts are
enabled to track error counts and reset where necessary. On IN
endpoints the host generates an ACK interrupt near-simultaneously
with completion of transfer. In the case where this transfer had
previously had an error, this results in a use-after-free on
the QTD memory space with a 1-byte length being overwritten to
0x00.
dwc_otg: add handling of SPLIT transaction data toggle errors
Previously a data toggle error on packets from a USB1.1 device behind
a TT would result in the Pi locking up as the driver never handled
the associated interrupt. Patch adds basic retry mechanism and
interrupt acknowledgement to cater for either a chance toggle error or
for devices that have a broken initial toggle state (FT8U232/FT232BM).
dwc_otg: implement tasklet for returning URBs to usbcore hcd layer
The dwc_otg driver interrupt handler for transfer completion will spend
a very long time with interrupts disabled when a URB is completed -
this is because usb_hcd_giveback_urb is called from within the handler
which for a USB device driver with complicated processing (e.g. webcam)
will take an exorbitant amount of time to complete. This results in
missed completion interrupts for other USB packets which lead to them
being dropped due to microframe overruns.
This patch splits returning the URB to the usb hcd layer into a
high-priority tasklet. This will have most benefit for isochronous IN
transfers but will also have incidental benefit where multiple periodic
devices are active at once.
dwc_otg: fix NAK holdoff and allow on split transactions only
This corrects a bug where if a single active non-periodic endpoint
had at least one transaction in its qh, on frnum == MAX_FRNUM the qh
would get skipped and never get queued again. This would result in
a silent device until error detection (automatic or otherwise) would
either reset the device or flush and requeue the URBs.
Additionally the NAK holdoff was enabled for all transactions - this
would potentially stall a HS endpoint for 1ms if a previous error state
enabled this interrupt and the next response was a NAK. Fix so that
only split transactions get held off.
dwc_otg: Call usb_hcd_unlink_urb_from_ep with lock held in completion handler
usb_hcd_unlink_urb_from_ep must be called with the HCD lock held. Calling it
asynchronously in the tasklet was not safe (regression in
c4564d4a1a).
This change unlinks it from the endpoint prior to queueing it for handling in
the tasklet, and also adds a check to ensure the urb is OK to be unlinked
before doing so.
NULL pointer dereference kernel oopses had been observed in usb_hcd_giveback_urb
when a USB device was unplugged/replugged during data transfer. This effect
was reproduced using automated USB port power control, hundreds of replug
events were performed during active transfers to confirm that the problem was
eliminated.
USB fix using a FIQ to implement split transactions
This commit adds a FIQ implementaion that schedules
the split transactions using a FIQ so we don't get
held off by the interrupt latency of Linux
dwc_otg: fix device attributes and avoid kernel warnings on boot
dcw_otg: avoid logging function that can cause panics
See: https://github.com/raspberrypi/firmware/issues/21
Thanks to cleverca22 for fix
dwc_otg: mask correct interrupts after transaction error recovery
The dwc_otg driver will unmask certain interrupts on a transaction
that previously halted in the error state in order to reset the
QTD error count. The various fine-grained interrupt handlers do not
consider that other interrupts besides themselves were unmasked.
By disabling the two other interrupts only ever enabled in DMA mode
for this purpose, we can avoid unnecessary function calls in the
IRQ handler. This will also prevent an unneccesary FIQ interrupt
from being generated if the FIQ is enabled.
dwc_otg: fiq: prevent FIQ thrash and incorrect state passing to IRQ
In the case of a transaction to a device that had previously aborted
due to an error, several interrupts are enabled to reset the error
count when a device responds. This has the side-effect of making the
FIQ thrash because the hardware will generate multiple instances of
a NAK on an IN bulk/interrupt endpoint and multiple instances of ACK
on an OUT bulk/interrupt endpoint. Make the FIQ mask and clear the
associated interrupts.
Additionally, on non-split transactions make sure that only unmasked
interrupts are cleared. This caused a hard-to-trigger but serious
race condition when you had the combination of an endpoint awaiting
error recovery and a transaction completed on an endpoint - due to
the sequencing and timing of interrupts generated by the dwc_otg core,
it was possible to confuse the IRQ handler.
Fix function tracing
dwc_otg: whitespace cleanup in dwc_otg_urb_enqueue
dwc_otg: prevent OOPSes during device disconnects
The dwc_otg_urb_enqueue function is thread-unsafe. In particular the
access of urb->hcpriv, usb_hcd_link_urb_to_ep, dwc_otg_urb->qtd and
friends does not occur within a critical section and so if a device
was unplugged during activity there was a high chance that the
usbcore hub_thread would try to disable the endpoint with partially-
formed entries in the URB queue. This would result in BUG() or null
pointer dereferences.
Fix so that access of urb->hcpriv, enqueuing to the hardware and
adding to usbcore endpoint URB lists is contained within a single
critical section.
dwc_otg: prevent BUG() in TT allocation if hub address is > 16
A fixed-size array is used to track TT allocation. This was
previously set to 16 which caused a crash because
dwc_otg_hcd_allocate_port would read past the end of the array.
This was hit if a hub was plugged in which enumerated as addr > 16,
due to previous device resets or unplugs.
Also add #ifdef FIQ_DEBUG around hcd->hub_port_alloc[], which grows
to a large size if 128 hub addresses are supported. This field is
for debug only for tracking which frame an allocate happened in.
dwc_otg: make channel halts with unknown state less damaging
If the IRQ received a channel halt interrupt through the FIQ
with no other bits set, the IRQ would not release the host
channel and never complete the URB.
Add catchall handling to treat as a transaction error and retry.
dwc_otg: fiq_split: use TTs with more granularity
This fixes certain issues with split transaction scheduling.
- Isochronous multi-packet OUT transactions now hog the TT until
they are completed - this prevents hubs aborting transactions
if they get a periodic start-split out-of-order
- Don't perform TT allocation on non-periodic endpoints - this
allows simultaneous use of the TT's bulk/control and periodic
transaction buffers
This commit will mainly affect USB audio playback.
dwc_otg: fix potential sleep while atomic during urb enqueue
Fixes a regression introduced with eb1b482a. Kmalloc called from
dwc_otg_hcd_qtd_add / dwc_otg_hcd_qtd_create did not always have
the GPF_ATOMIC flag set. Force this flag when inside the larger
critical section.
dwc_otg: make fiq_split_enable imply fiq_fix_enable
Failing to set up the FIQ correctly would result in
"IRQ 32: nobody cared" errors in dmesg.
dwc_otg: prevent crashes on host port disconnects
Fix several issues resulting in crashes or inconsistent state
if a Model A root port was disconnected.
- Clean up queue heads properly in kill_urbs_in_qh_list by
removing the empty QHs from the schedule lists
- Set the halt status properly to prevent IRQ handlers from
using freed memory
- Add fiq_split related cleanup for saved registers
- Make microframe scheduling reclaim host channels if
active during a disconnect
- Abort URBs with -ESHUTDOWN status response, informing
device drivers so they respond in a more correct fashion
and don't try to resubmit URBs
- Prevent IRQ handlers from attempting to handle channel
interrupts if the associated URB was dequeued (and the
driver state was cleared)
dwc_otg: prevent leaking URBs during enqueue
A dwc_otg_urb would get leaked if the HCD enqueue function
failed for any reason. Free the URB at the appropriate points.
dwc_otg: Enable NAK holdoff for control split transactions
Certain low-speed devices take a very long time to complete a
data or status stage of a control transaction, producing NAK
responses until they complete internal processing - the USB2.0
spec limit is up to 500mS. This causes the same type of interrupt
storm as seen with USB-serial dongles prior to c8edb238.
In certain circumstances, usually while booting, this interrupt
storm could cause SD card timeouts.
dwc_otg: Fix for occasional lockup on boot when doing a USB reset
dwc_otg: Don't issue traffic to LS devices in FS mode
Issuing low-speed packets when the root port is in full-speed mode
causes the root port to stop responding. Explicitly fail when
enqueuing URBs to a LS endpoint on a FS bus.
Fix ARM architecture issue with local_irq_restore()
If local_fiq_enable() is called before a local_irq_restore(flags) where
the flags variable has the F bit set, the FIQ will be erroneously disabled.
Fixup arch_local_irq_restore to avoid trampling the F bit in CPSR.
Also fix some of the hacks previously implemented for previous dwc_otg
incarnations.
dwc_otg: fiq_fsm: Base commit for driver rewrite
This commit removes the previous FIQ fixes entirely and adds fiq_fsm.
This rewrite features much more complete support for split transactions
and takes into account several OTG hardware bugs. High-speed
isochronous transactions are also capable of being performed by fiq_fsm.
All driver options have been removed and replaced with:
- dwc_otg.fiq_enable (bool)
- dwc_otg.fiq_fsm_enable (bool)
- dwc_otg.fiq_fsm_mask (bitmask)
- dwc_otg.nak_holdoff (unsigned int)
Defaults are specified such that fiq_fsm behaves similarly to the
previously implemented FIQ fixes.
fiq_fsm: Push error recovery into the FIQ when fiq_fsm is used
If the transfer associated with a QTD failed due to a bus error, the HCD
would retry the transfer up to 3 times (implementing the USB2.0
three-strikes retry in software).
Due to the masking mechanism used by fiq_fsm, it is only possible to pass
a single interrupt through to the HCD per-transfer.
In this instance host channels would fall off the radar because the error
reset would function, but the subsequent channel halt would be lost.
Push the error count reset into the FIQ handler.
fiq_fsm: Implement timeout mechanism
For full-speed endpoints with a large packet size, interrupt latency
runs the risk of the FIQ starting a transaction too late in a full-speed
frame. If the device is still transmitting data when EOF2 for the
downstream frame occurs, the hub will disable the port. This change is
not reflected in the hub status endpoint and the device becomes
unresponsive.
Prevent high-bandwidth transactions from being started too late in a
frame. The mechanism is not guaranteed: a combination of bit stuffing
and hub latency may still result in a device overrunning.
fiq_fsm: fix bounce buffer utilisation for Isochronous OUT
Multi-packet isochronous OUT transactions were subject to a few bounday
bugs. Fix them.
Audio playback is now much more robust: however, an issue stands with
devices that have adaptive sinks - ALSA plays samples too fast.
dwc_otg: Return full-speed frame numbers in HS mode
The frame counter increments on every *microframe* in high-speed mode.
Most device drivers expect this number to be in full-speed frames - this
caused considerable confusion to e.g. snd_usb_audio which uses the
frame counter to estimate the number of samples played.
fiq_fsm: save PID on completion of interrupt OUT transfers
Also add edge case handling for interrupt transports.
Note that for periodic split IN, data toggles are unimplemented in the
OTG host hardware - it unconditionally accepts any PID.
fiq_fsm: add missing case for fiq_fsm_tt_in_use()
Certain combinations of bitrate and endpoint activity could
result in a periodic transaction erroneously getting started
while the previous Isochronous OUT was still active.
fiq_fsm: clear hcintmsk for aborted transactions
Prevents the FIQ from erroneously handling interrupts
on a timed out channel.
fiq_fsm: enable by default
fiq_fsm: fix dequeues for non-periodic split transactions
If a dequeue happened between the SSPLIT and CSPLIT phases of the
transaction, the HCD would never receive an interrupt.
fiq_fsm: Disable by default
fiq_fsm: Handle HC babble errors
The HCTSIZ transfer size field raises a babble interrupt if
the counter wraps. Handle the resulting interrupt in this case.
dwc_otg: fix interrupt registration for fiq_enable=0
Additionally make the module parameter conditional for wherever
hcd->fiq_state is touched.
fiq_fsm: Enable by default
dwc_otg: Fix various issues with root port and transaction errors
Process the host port interrupts correctly (and don't trample them).
Root port hotplug now functional again.
Fix a few thinkos with the transaction error passthrough for fiq_fsm.
fiq_fsm: Implement hack for Split Interrupt transactions
Hubs aren't too picky about which endpoint we send Control type split
transactions to. By treating Interrupt transfers as Control, it is
possible to use the non-periodic queue in the OTG core as well as the
non-periodic FIFOs in the hub itself. This massively reduces the
microframe exclusivity/contention that periodic split transactions
otherwise have to enforce.
It goes without saying that this is a fairly egregious USB specification
violation, but it works.
Original idea by Hans Petter Selasky @ FreeBSD.org.
dwc_otg: FIQ support on SMP. Set up FIQ stack and handler on Core 0 only.
dwc_otg: introduce fiq_fsm_spin(un|)lock()
SMP safety for the FIQ relies on register read-modify write cycles being
completed in the correct order. Several places in the DWC code modify
registers also touched by the FIQ. Protect these by a bare-bones lock
mechanism.
This also makes it possible to run the FIQ and IRQ handlers on different
cores.
fiq_fsm: fix build on bcm2708 and bcm2709 platforms
dwc_otg: put some barriers back where they should be for UP
bcm2709/dwc_otg: Setup FIQ on core 1 if >1 core active
dwc_otg: fixup read-modify-write in critical paths
Be more careful about read-modify-write on registers that the FIQ
also touches.
Guard fiq_fsm_spin_lock with fiq_enable check
fiq_fsm: Falling out of the state machine isn't fatal
This edge case can be hit if the port is disabled while the FIQ is
in the middle of a transaction. Make the effects less severe.
Also get rid of the useless return value.
squash: dwc_otg: Allow to build without SMP
usb: core: make overcurrent messages more prominent
Hub overcurrent messages are more serious than "debug". Increase loglevel.
usb: dwc_otg: Don't use dma_to_virt()
Commit 6ce0d20 changes dma_to_virt() which breaks this driver.
Open code the old dma_to_virt() implementation to work around this.
Limit the use of __bus_to_virt() to cases where transfer_buffer_length
is set and transfer_buffer is not set. This is done to increase the
chance that this driver will also work on ARCH_BCM2835.
transfer_buffer should not be NULL if the length is set, but the
comment in the code indicates that there are situations where this
might happen. drivers/usb/isp1760/isp1760-hcd.c also has a similar
comment pointing to a possible: 'usb storage / SCSI bug'.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: Fix crash when fiq_enable=0
dwc_otg: fiq_fsm: Make high-speed isochronous strided transfers work properly
Certain low-bandwidth high-speed USB devices (specialist audio devices,
compressed-frame webcams) have packet intervals > 1 microframe.
Stride these transfers in the FIQ by using the start-of-frame interrupt
to restart the channel at the right time.
dwc_otg: Force host mode to fix incorrect compute module boards
dwc_otg: Add ARCH_BCM2835 support
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: Simplify FIQ irq number code
Dropping ATAGS means we can simplify the FIQ irq number code.
Also add error checking on the returned irq number.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: Remove duplicate gadget probe/unregister function
dwc_otg: Properly set the HFIR
Douglas Anderson reported:
According to the most up to date version of the dwc2 databook, the FRINT
field of the HFIR register should be programmed to:
* 125 us * (PHY clock freq for HS) - 1
* 1000 us * (PHY clock freq for FS/LS) - 1
This is opposed to older versions of the doc that claimed it should be:
* 125 us * (PHY clock freq for HS)
* 1000 us * (PHY clock freq for FS/LS)
and reported lower timing jitter on a USB analyser
dcw_otg: trim xfer length when buffer larger than allocated size is received
dwc_otg: Don't free qh align buffers in atomic context
dwc_otg: Enable the hack for Split Interrupt transactions by default
dwc_otg.fiq_fsm_mask=0xF has long been a suggestion for users with audio stutters or other USB bandwidth issues.
So far we are aware of many success stories but no failure caused by this setting.
Make it a default to learn more.
See: https://www.raspberrypi.org/forums/viewtopic.php?f=28&t=70437
Signed-off-by: popcornmix <popcornmix@gmail.com>
dwc_otg: Use kzalloc when suitable
dwc_otg: Pass struct device to dma_alloc*()
This makes it possible to get the bus address from Device Tree.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: fix summarize urb->actual_length for isochronous transfers
Kernel does not copy input data of ISO transfers to userspace
if actual_length is set only in ISO transfers and not summarized
in urb->actual_length. Fixesraspberrypi/linux#903
fiq_fsm: Use correct states when starting isoc OUT transfers
In fiq_fsm_start_next_periodic() if an isochronous OUT transfer
was selected, no regard was given as to whether this was a single-packet
transfer or a multi-packet staged transfer.
For single-packet transfers, this had the effect of repeatedly sending
OUT packets with bogus data and lengths.
Eventually if the channel was repeatedly enabled enough times, this
would lock up the OTG core and no further bus transfers would happen.
Set the FSM state up properly if we select a single-packet transfer.
Fixes https://github.com/raspberrypi/linux/issues/1842
dwc_otg: make nak_holdoff work as intended with empty queues
If URBs reading from non-periodic split endpoints were dequeued and
the last transfer from the endpoint was a NAK handshake, the resulting
qh->nak_frame value was stale which would result in unnecessarily long
polling intervals for the first subsequent transfer with a fresh URB.
Fixup qh->nak_frame in dwc_otg_hcd_urb_dequeue and also guard against
a case where a single URB is submitted to the endpoint, a NAK was
received on the transfer immediately prior to receiving data and the
device subsequently resubmits another URB past the qh->nak_frame interval.
Fixes https://github.com/raspberrypi/linux/issues/1709
dwc_otg: fix split transaction data toggle handling around dequeues
See https://github.com/raspberrypi/linux/issues/1709
Fix several issues regarding endpoint state when URBs are dequeued
- If the HCD is disconnected, flush FIQ-enabled channels properly
- Save the data toggle state for bulk endpoints if the last transfer
from an endpoint where URBs were dequeued returned a data packet
- Reset hc->start_pkt_count properly in assign_and_init_hc()
dwc_otg: fix several potential crash sources
On root port disconnect events, the host driver state is cleared and
in-progress host channels are forcibly stopped. This doesn't play
well with the FIQ running in the background, so:
- Guard the disconnect callback with both the host spinlock and FIQ
spinlock
- Move qtd dereference in dwc_otg_handle_hc_fsm() after the early-out
so we don't dereference a qtd that has gone away
- Turn catch-all BUG()s in dwc_otg_handle_hc_fsm() into warnings.
dwc_otg: delete hcd->channel_lock
The lock serves no purpose as it is only held while the HCD spinlock
is already being held.
dwc_otg: remove unnecessary dma-mode channel halts on disconnect interrupt
Host channels are already halted in kill_urbs_in_qh_list() with the
subsequent interrupt processing behaving as if the URB was dequeued
via HCD callback.
There's no need to clobber the host channel registers a second time
as this exposes races between the driver and host channel resulting
in hcd->free_hc_list becoming corrupted.
dwcotg: Allow to build without FIQ on ARM64
Signed-off-by: popcornmix <popcornmix@gmail.com>
dwc_otg: make periodic scheduling behave properly for FS buses
If the root port is in full-speed mode, transfer times at 12mbit/s
would be calculated but matched against high-speed quotas.
Reinitialise hcd->frame_usecs[i] on each port enable event so that
full-speed bandwidth can be tracked sensibly.
Also, don't bother using the FIQ for transfers when in full-speed
mode - at the slower bus speed, interrupt frequency is reduced by
an order of magnitude.
Related issue: https://github.com/raspberrypi/linux/issues/2020
dwc_otg: fiq_fsm: Make isochronous compatibility checks work properly
Get rid of the spammy printk and local pointer mangling.
Also, there is a nominal benefit for using fiq_fsm for isochronous
transfers in FS mode (~1.1k IRQs per second vs 2.1k IRQs per second)
so remove the root port speed check.
dwc_otg: add module parameter int_ep_interval_min
Add a module parameter (defaulting to ignored) that clamps the polling rate
of high-speed Interrupt endpoints to a minimum microframe interval.
The parameter is modifiable at runtime as it is used when activating new
endpoints (such as on device connect).
dwc_otg: fiq_fsm: Add non-periodic TT exclusivity constraints
Certain hub types do not discriminate between pipe direction (IN or OUT)
when considering non-periodic transfers. Therefore these hubs get confused
if multiple transfers are issued in different directions with the same
device address and endpoint number.
Constrain queuing non-periodic split transactions so they are performed
serially in such cases.
Related: https://github.com/raspberrypi/linux/issues/2024
dwc_otg: Fixup change to DRIVER_ATTR interface
dwc_otg: Fix compilation warnings
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
USB_DWCOTG: Disable building dwc_otg as a module (#2265)
When dwc_otg is built as a module, build will fail with the following
error:
ERROR: "DWC_TASK_HI_SCHEDULE" [drivers/usb/host/dwc_otg/dwc_otg.ko] undefined!
scripts/Makefile.modpost:91: recipe for target '__modpost' failed
make[1]: *** [__modpost] Error 1
Makefile:1199: recipe for target 'modules' failed
make: *** [modules] Error 2
Even if the error is solved by including the missing
DWC_TASK_HI_SCHEDULE function, the kernel will panic when loading
dwc_otg.
As a workaround, simply prevent user from building dwc_otg as a module
as the current kernel does not support it.
See: https://github.com/raspberrypi/linux/issues/2258
Signed-off-by: Malik Olivier Boussejra <malik@boussejra.com>
dwc_otg: New timer API
dwc_otg: Fix removed ACCESS_ONCE->READ_ONCE
dwc_otg: don't unconditionally force host mode in dwc_otg_cil_init()
Add the ability to disable force_host_mode for those that want to use
dwc_otg in both device and host modes.
dwc_otg: Fix a regression when dequeueing isochronous transfers
In 282bed95 (dwc_otg: make nak_holdoff work as intended with empty queues)
the dequeue mechanism was changed to leave FIQ-enabled transfers to run
to completion - to avoid leaving hub TT buffers with stale packets lying
around.
This broke FIQ-accelerated isochronous transfers, as this then meant that
dozens of transfers were performed after the dequeue function returned.
Restore the state machine fence for isochronous transfers.
fiq_fsm: rewind DMA pointer for OUT transactions that fail (#2288)
See: https://github.com/raspberrypi/linux/issues/2140
dwc_otg: add smp_mb() to prevent driver state corruption on boot
Occasional crashes have been seen where the FIQ code dereferences
invalid/random pointers immediately after being set up, leading to
panic on boot.
The crash occurs as the FIQ code races against hcd_init_fiq() and
the hcd_init_fiq() code races against the outstanding memory stores
from dwc_otg_hcd_init(). Use explicit barriers after touching
driver state.
usb: dwc_otg: fix memory corruption in dwc_otg driver
[Upstream commit 51b1b64917]
The move from the staging tree to the main tree exposed a
longstanding memory corruption bug in the dwc2 driver. The
reordering of the driver initialization caused the dwc2 driver
to corrupt the initialization data of the sdhci driver on the
Raspberry Pi platform, which made the bug show up.
The error is in calling to_usb_device(hsotg->dev), since ->dev
is not a member of struct usb_device. The easiest fix is to
just remove the offending code, since it is not really needed.
Thanks to Stephen Warren for tracking down the cause of this.
Reported-by: Andre Heider <a.heider@gmail.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[lukas: port from upstream dwc2 to out-of-tree dwc_otg driver]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
usb: dwb_otg: Fix unreachable switch statement warning
This warning appears with GCC 7.3.0 from toolchains.bootlin.com:
../drivers/usb/host/dwc_otg/dwc_otg_fiq_fsm.c: In function ‘fiq_fsm_update_hs_isoc’:
../drivers/usb/host/dwc_otg/dwc_otg_fiq_fsm.c:595:61: warning: statement will never be executed [-Wswitch-unreachable]
st->hctsiz_copy.b.xfersize = nrpackets * st->hcchar_copy.b.mps;
~~~~~~~~~~~~~~~~~^~~~
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
dwc_otg: fiq_fsm: fix incorrect DMA register offset calculation
Rationalise the offset and update all call sites.
Fixes https://github.com/raspberrypi/linux/issues/2408
dwc_otg: fix bug with port_addr assignment for single-TT hubs
See https://github.com/raspberrypi/linux/issues/2734
The "Hub Port" field in the split transaction packet was always set
to 1 for single-TT hubs. The majority of single-TT hub products
apparently ignore this field and broadcast to all downstream enabled
ports, which masked the issue. A subset of hub devices apparently
need the port number to be exact or split transactions will fail.
usb: dwc_otg: Clean up build warnings on 64bit kernels
No functional changes. Almost all are changes to logging lines.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
usb: dwc_otg: Use dma allocation for mphi dummy_send buffer
The FIQ driver used a kzalloc'ed buffer for dummy_send,
passing a kernel virtual address to the hardware block.
The buffer is only ever used for a dummy read, so it
should be harmless, but there is the chance that it will
cause exceptions.
Use a dma allocation so that we have a genuine bus address,
and read from that.
Free the allocation when done for good measure.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
dwc_otg: only do_split when we actually need to do a split
The previous test would fail if the root port was in fullspeed mode
and there was a hub between the FS device and the root port. While
the transfer worked, the schedule mangling performed for high-speed
split transfers would break leading to an 8ms polling interval.
dwc_otg: fix locking around dequeueing and killing URBs
kill_urbs_in_qh_list() is practically only ever called with the fiq lock
already held, so don't spinlock twice in the case where we need to cancel
an isochronous transfer.
Also fix up a case where the global interrupt register could be read with
the fiq lock not held.
Fixes the deadlock seen in https://github.com/raspberrypi/linux/issues/2907
ARM64/DWC_OTG: Port dwc_otg driver to ARM64
In ARM64, the FIQ mechanism used by this driver is not current
implemented. As a workaround, reqular IRQ is used instead
of FIQ.
In a separate change, the IRQ-CPU mapping is round robined
on ARM64 to increase concurrency and allow multiple interrupts
to be serviced at a time. This reduces the need for FIQ.
Tests Run:
This mechanism is most likely to break when multiple USB devices
are attached at the same time. So the system was tested under
stress.
Devices:
1. USB Speakers playing back a FLAC audio through VLC
at 96KHz.(Higher then typically, but supported on my speakers).
2. sftp transferring large files through the buildin ethernet
connection which is connected through USB.
3. Keyboard and mouse attached and being used.
Although I do occasionally hear some glitches, the music seems to
play quite well.
Signed-off-by: Michael Zoran <mzoran@crowfest.net>
usb: dwc_otg: Clean up interrupt claiming code
The FIQ/IRQ interrupt number identification code is scattered through
the dwc_otg driver. Rationalise it, simplifying the code and solving
an existing issue.
See: https://github.com/raspberrypi/linux/issues/2612
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
dwc_otg: Choose appropriate IRQ handover strategy
2711 has no MPHI peripheral, but the ARM Control block can fake
interrupts. Use the size of the DTB "mphi" reg block to determine
which is required.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
usb: host: dwc_otg: fix compiling in separate directory
The dwc_otg Makefile does not respect the O=path argument correctly:
include paths in CFLAGS are given relatively to object path, not source
path. Compiling in a separate directory yields #include errors.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
dwc_otg: use align_buf for small IN control transfers (#3150)
The hardware will do a 4-byte write to memory on any IN packet received
that is between 1 and 3 bytes long. This tramples memory in the uvcvideo
driver, as it uses a sequence of 1- and 2-byte control transfers to
query the min/max/range/step of each individual camera control and
gives us buffers that are offsets into a struct.
Catch small control transfers in the data phase and use the align_buf
to bounce the correct number of bytes into the URB's buffer.
In general, short packets on non-control endpoints should be OK as URBs
should have enough buffer space for a wMaxPacket size transfer.
See: https://github.com/raspberrypi/linux/issues/3148
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
dwc_otg: Declare DMA capability with HCD_DMA flag
Following [1], USB controllers have to declare DMA capabilities in
order for them to be used by adding the HCD_DMA flag to their hc_driver
struct.
[1] 7b81cb6bdd ("usb: add a HCD_DMA flag instead of guestimating DMA capabilities")
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
dwc_otg: checking the urb->transfer_buffer too early (#3332)
After enable the HIGHMEM and VMSPLIT_3G, the dwc_otg driver doesn't
work well on Pi2/3 boards with 1G physical ram. Users experience
the failure when copying a file of 600M size to the USB stick. And
at the same time, the dmesg shows:
usb 1-1.1.2: reset high-speed USB device number 8 using dwc_otg
sd 0:0:0:0: [sda] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
blk_update_request: I/O error, dev sda, sector 3024048 op 0x1:(WRITE) flags 0x4000 phys_seg 15 prio class 0
When this happens, the sg_buf sent to the driver is located in the
highmem region, the usb_sg_init() in the core/message.c will leave
transfer_buffer to NULL if the sg_buf is in highmem, but in the
dwc_otg driver, it returns -EINVAL unconditionally if transfer_buffer
is NULL.
The driver can handle the situation of buffer to be NULL, if it is in
DMA mode, it will convert an address from transfer_dma.
But if the conversion fails or it is in the PIO mode, we should check
buffer and return -EINVAL if it is NULL.
BugLink: https://bugs.launchpad.net/bugs/1852510
Signed-off-by: Hui Wang <hui.wang@canonical.com>
dwc_otg: constrain endpoint max packet and transfer size on split IN
The hcd would unconditionally set the transfer length to the endpoint
packet size for non-isoc IN transfers. If the remaining buffer length
was less than the length of returned data, random memory would get
scribbled over, with bad effects if it crossed a page boundary.
Force a babble error if this happens by limiting the max transfer size
to the available buffer space. DMA will stop writing to memory on a
babble condition.
The hardware expects xfersize to be an integer multiple of maxpacket
size, so override hcchar.b.mps as well.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
dwc_otg: fiq_fsm: pause when cancelling split transactions
Non-periodic splits will DMA to/from the driver-provided transfer_buffer,
which may be freed immediately after the dequeue call returns. Block until
we know the transfer is complete.
A similar delay is needed when cleaning up disconnects, as the FIQ could
have started a periodic transfer in the previous microframe to the one
that triggered a disconnect.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
dwc_otg: fiq_fsm: add a barrier on entry into FIQ handler(s)
On BCM2835, there is no hardware guarantee that multiple outstanding
reads to different peripherals will complete in-order. The FIQ code
uses peripheral reads without barriers for performance, so in the case
where a read to a slow peripheral was issued immediately prior to FIQ
entry, the first peripheral read that the FIQ did could end up with
wrong read data returned.
Add dsb(sy) on entry so that all outstanding reads are retired.
The FIQ only issues reads to the dwc_otg core, so per-read barriers
in the handler itself are not required.
On BCM2836 and BCM2837 the barrier is not strictly required due to
differences in how the peripheral bus is implemented, but having
arch-specific handlers that introduce different latencies is risky.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Signed-off-by: popcornmix <popcornmix@gmail.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2709: Drop platform smp and timer init code
irq-bcm2836 handles this through these functions:
bcm2835_init_local_timer_frequency()
bcm2836_arm_irqchip_smp_init()
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm270x: Use watchdog for reboot/poweroff
The watchdog driver already has support for reboot/poweroff.
Make use of this and remove the code from the platform files.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
board_bcm2835: Remove coherent dma pool increase - API has gone
Under some circumstances on BCM283x processors data loss can be
observed - a single byte missing from the TX output stream. These bytes
are always the last byte of a batch of 8 written from pl011_tx_chars
when from_irq is true, meaning that the FIFO full flag is not checked
before writing.
The transmit optimisation relies on the FIFO being half-empty when the
TX interrupt is raised. Instrumenting the driver further showed that
the failure case correlated with the TX FIFO full flag being set at the
point where the last byte was written to the data register, which
explains the data loss but not how the FIFO appeared to be prematurely
full. A possible explanation is that a FIFO write was in flight at the
time the interrupt was raised, but as yet there is no hypothesis as to
how this might occur.
In the absence of a clear understanding of the failure mechanism, avoid
the problem by checking the FIFO levels before writing the last byte of
the group, which will have minimal performance impact.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The PL011 driver lacks throttle and unthrottle methods. As a result,
sending more data to the Pi than it can immediately sink while CRTSCTS
is enabled causes a NULL pointer to be followed.
Add a throttle handler that disables the RX interrupts, and an
unthrottle handler that reenables them.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
pl011_tx_chars takes a "from_irq" parameter to reduce the number of
register accesses. When from_irq is true the function assumes that the
FIFO is half empty and writes up to half a FIFO's worth of bytes
without polling the FIFO status register, the reasoning being that
the function is being called as a result of the TX interrupt being
raised. This logic would work were it not for the fact that
pl011_rx_chars, called from pl011_int before pl011_tx_chars, releases
the spinlock before calling tty_flip_buffer_push.
A user thread writing to the UART claims the spinlock and ultimately
calls pl011_tx_chars with from_irq set to false. This reverts to the
older logic that polls the FIFO status register before sending every
byte. If this happen on an SMP system during the section of the IRQ
handler where the spinlock has been released, then by the time the TX
interrupt handler is called, the FIFO may already be full, and any
further writes are likely to be lost.
The fix involves adding a per-port flag that is true iff running from
within the interrupt handler and the spinlock has not yet been released.
This flag is then used as the value for the from_irq parameter of
pl011_tx_chars, causing polling to be used in the unsafe case.
Fixes: 1e84d22322 ("serial/amba-pl011: Refactor and simplify TX FIFO handling")
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The BCM2835 PL011 implementation seems to have a bug that can lead to a
transmission lockup if CTS changes frequently. A workaround was added to
the driver with a vendor-specific flag to enable it, but this flag is
currently not set for ARM implementations.
Add a "cts-event-workaround" property to Pi DTBs and use the presence
of that property to force the flag to be enabled in the driver.
See: https://github.com/raspberrypi/linux/issues/1280
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The pl011 register accessor functions use the _relaxed versions of the
standard readl() and writel() functions, meaning that there are no
automatic memory barriers. When polling a FIFO status register to check
for fullness, it is necessary to ensure that any outstanding writes have
completed; otherwise the flags are effectively stale, making it possible
that the next write is to a full FIFO.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The UART clock is initialised to be as close to the requested
frequency as possible without exceeding it. Now that there is a
clock manager that returns the actual frequencies, an expected
48MHz clock is reported as 47999625. If the requested baudrate
== requested clock/16, there is no headroom and the slight
reduction in actual clock rate results in failure.
Detect cases where it looks like a "round" clock was chosen and
adjust the reported clock to match that "round" value. As the
code comment says:
/*
* If increasing a clock by less than 0.1% changes it
* from ..999.. to ..000.., round up.
*/
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The pl011 driver looks for DT aliases of the form "serial<n>",
and if found uses <n> as the device ID. This can cause
/dev/ttyAMA0 to become /dev/ttyAMA1, which is confusing if the
other serial port is provided by the 8250 driver which doesn't
use the same logic.
For applications of the LAN78xx that don't have valid programmed
EEPROMs or OTPs, enabling both LEDs and auto-negotiation by default
seems reasonable.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The syscon node defines a register range that duplicates that used by
the local_intc node on bcm2836/7. Since irq-bcm2835 and irq-bcm2836 are
built in and always present together (both drivers are enabled by
CONFIG_ARCH_BCM2835), it is possible to replace the syscon usage with a
global variable that simplifies the code. Doing so does lose the
locking provided by regmap, but as only one side is using the regmap
interface (irq-bcm2835 uses readl and write) there is no loss of
atomicity.
See: https://github.com/raspberrypi/firmware/issues/926
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
See commit dae803e165 -- the warning is
expected sometimes when using CMA. However, that commit still spams
my kernel log with these warnings.
Signed-off-by: Eric Anholt <eric@anholt.net>
This adds a debug module parameter to aid in debugging transfer issues
by printing info to the kernel log. When enabled, status values are
collected in the interrupt routine and msg info in
bcm2835_i2c_start_transfer(). This is done in a way that tries to avoid
affecting timing. Having printk in the isr can mask issues.
debug values (additive):
1: Print info on error
2: Print info on all transfers
3: Print messages before transfer is started
The value can be changed at runtime:
/sys/module/i2c_bcm2835/parameters/debug
Example output, debug=3:
[ 747.114448] bcm2835_i2c_xfer: msg(1/2) write addr=0x54, len=2 flags= [i2c1]
[ 747.114463] bcm2835_i2c_xfer: msg(2/2) read addr=0x54, len=32 flags= [i2c1]
[ 747.117809] start_transfer: msg(1/2) write addr=0x54, len=2 flags= [i2c1]
[ 747.117825] isr: remain=2, status=0x30000055 : TA TXW TXD TXE [i2c1]
[ 747.117839] start_transfer: msg(2/2) read addr=0x54, len=32 flags= [i2c1]
[ 747.117849] isr: remain=32, status=0xd0000039 : TA RXR TXD RXD [i2c1]
[ 747.117861] isr: remain=20, status=0xd0000039 : TA RXR TXD RXD [i2c1]
[ 747.117870] isr: remain=8, status=0x32 : DONE TXD RXD [i2c1]
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Christopher Alexander Tobias Schulze - May 2, 2015, 11:57 a.m.
This patch fixes a problem with VFP state save and restore related
to exception handling (panic with message "BUG: unsupported FP
instruction in kernel mode") present on VFP11 floating point units
(as used with ARM1176JZF-S CPUs, e.g. on first generation Raspberry
Pi boards). This patch was developed and discussed on
https://github.com/raspberrypi/linux/issues/859
A precondition to see the crashes is that floating point exception
traps are enabled. In this case, the VFP11 might determine that a FPU
operation needs to trap at a point in time when it is not possible to
signal this to the ARM11 core any more. The VFP11 will then set the
FPEXC.EX bit and store the trapped opcode in FPINST. (In some cases,
a second opcode might have been accepted by the VFP11 before the
exception was detected and could be reported to the ARM11 - in this
case, the VFP11 also sets FPEXC.FP2V and stores the second opcode in
FPINST2.)
If FPEXC.EX is set, the VFP11 will "bounce" the next FPU opcode issued
by the ARM11 CPU, which will be seen by the ARM11 as an undefined opcode
trap. The VFP support code examines the FPEXC.EX and FPEXC.FP2V bits
to decide what actions to take, i.e., whether to emulate the opcodes
found in FPINST and FPINST2, and whether to retry the bounced instruction.
If a user space application has left the VFP11 in this "pending trap"
state, the next FPU opcode issued to the VFP11 might actually be the
VSTMIA operation vfp_save_state() uses to store the FPU registers
to memory (in our test cases, when building the signal stack frame).
In this case, the kernel crashes as described above.
This patch fixes the problem by making sure that vfp_save_state() is
always entered with FPEXC.EX cleared. (The current value of FPEXC has
already been saved, so this does not corrupt the context. Clearing
FPEXC.EX has no effects on FPINST or FPINST2. Also note that many
callers already modify FPEXC by setting FPEXC.EN before invoking
vfp_save_state().)
This patch also addresses a second problem related to FPEXC.EX: After
returning from signal handling, the kernel reloads the VFP context
from the user mode stack. However, the current code explicitly clears
both FPEXC.EX and FPEXC.FP2V during reload. As VFP11 requires these
bits to be preserved, this patch disables clearing them for VFP
implementations belonging to architecture 1. There should be no
negative side effects: the user can set both bits by executing FPU
opcodes anyway, and while user code may now place arbitrary values
into FPINST and FPINST2 (e.g., non-VFP ARM opcodes) the VFP support
code knows which instructions can be emulated, and rejects other
opcodes with "unhandled bounce" messages, so there should be no
security impact from allowing reloading FPEXC.EX and FPEXC.FP2V.
Signed-off-by: Christopher Alexander Tobias Schulze <cat.schulze@alice-dsl.net>
At present there is no mechanism to specify driver load order,
which can lead to deferrals and repeated retries until successful.
Since this situation is expected, reduce the dmesg level to
INFO and mention that the operation will be retried.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The VPU is responsible for managing the core clock, usually under
direction from the bcm2835-cpufreq driver but not via the clk-bcm2835
driver. Since the core frequency can change without warning, it is
safer to report the maximum clock rate to users of the core clock -
I2C, SPI and the mini UART - to err on the safe side when calculating
clock divisors.
If the DT node for the clock driver includes a reference to the
firmware node, use the firmware API to query the maximum core clock
instead of reading the divider registers.
Prior to this patch, a "100KHz" I2C bus was sometimes clocked at about
160KHz. In particular, switching to the 4.9 kernel was likely to break
SenseHAT usage on a Pi3.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The claim-clocks property can be used to prevent PLLs and dividers
from being marked as critical. It contains a vector of clock IDs,
as defined by dt-bindings/clock/bcm2835.h.
Use this mechanism to claim PLLD_DSI0, PLLD_DSI1, PLLH_AUX and
PLLH_PIX for the vc4_kms_v3d driver.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The VPU configures and relies on several PLLs and dividers. Mark all
enabled dividers and their PLLs as CRITICAL to prevent the kernel from
switching them off.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The Raspberry Pi firmware looks at the RSTS register to know which
partition to boot from. The reboot syscall command
LINUX_REBOOT_CMD_RESTART2 supports passing in a string argument.
Add support for passing in a partition number 0..63 to boot from.
Partition 63 is a special partiton indicating halt.
If the partition doesn't exist, the firmware falls back to partition 0.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Load driver early since at least bcm2708_fb doesn't support deferred
probing and even if it did, we don't want the video driver deferred.
Support the legacy DMA API which is needed by bcm2708_fb.
Don't mask out channel 2.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
An alternative strategy would be to use "rpi,spidev" instead, but that
would require many Raspberry Pi Device Tree changes.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Add a duplicate irq range with an offset on the hwirq's so the
driver can detect that enable_fiq() is used.
Tested with downstream dwc_otg USB controller driver.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
smsc95xx is adjusting truesize when it shouldn't, and following a recent patch from Eric this is now triggering warnings.
This patch stops smsc95xx from changing truesize.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
This reverts commit c7dacf5b0f.
The Pi 400 shutdown/poweroff mechanism relies on being able to set
a GPIO on the expander in the pm_power_off handler, something that
requires two mailbox calls - GET_GPIO_STATE and SET_GPIO_STATE. A
recent kernel change introduces a reasonable possibility that the
GET call doesn't completes, and bisecting led to a commit from
October that changes the timer usage of the mailbox.
My theory is that there is a race condition in the new code that breaks
the poll timer, but that it normally goes unnoticed because subsequent
mailbox activity wakes it up again. The power-off mailbox calls happen
at a time when other subsystems have been shut down, so if one of them
fails then there is nothing to allow it to recover.
See: https://github.com/raspberrypi/linux/issues/3941
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
commit d3921cb8be upstream.
There could be struct pages that are not backed by actual physical
memory. This can happen when the actual memory bank is not a multiple
of SECTION_SIZE or when an architecture does not register memory holes
reserved by the firmware as memblock.memory.
Such pages are currently initialized using init_unavailable_mem()
function that iterates through PFNs in holes in memblock.memory and if
there is a struct page corresponding to a PFN, the fields if this page
are set to default values and the page is marked as Reserved.
init_unavailable_mem() does not take into account zone and node the page
belongs to and sets both zone and node links in struct page to zero.
On a system that has firmware reserved holes in a zone above ZONE_DMA,
for instance in a configuration below:
# grep -A1 E820 /proc/iomem
7a17b000-7a216fff : Unknown E820 type
7a217000-7bffffff : System RAM
unset zone link in struct page will trigger
VM_BUG_ON_PAGE(!zone_spans_pfn(page_zone(page), pfn), page);
because there are pages in both ZONE_DMA32 and ZONE_DMA (unset zone link
in struct page) in the same pageblock.
Update init_unavailable_mem() to use zone constraints defined by an
architecture to properly setup the zone link and use node ID of the
adjacent range in memblock.memory to set the node link.
Link: https://lkml.kernel.org/r/20210111194017.22696-3-rppt@kernel.org
Fixes: 73a6e474cb ("mm: memmap_init: iterate over memblock regions rather that check each PFN")
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Reported-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Hildenbrand <david@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Qian Cai <cai@lca.pw>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9f12e37cae upstream.
[ Also moved the declaration of redirected_tty_write() to the proper
location in a header file. The reason for the bug was the bogus extern
declaration in n_tty.c silently not matching the changed definition in
tty_io.c, and because it wasn't in a shared header file, there was no
cross-checking of the declaration.
Sami noticed because Clang's Control Flow Integrity checking ended up
incidentally noticing the inconsistent declaration. - Linus ]
Fixes: 9bb48c82ac ("tty: implement write_iter")
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f8ad8187c3 upstream.
After commit 36e2c7421f ("fs: don't allow splice read/write
without explicit ops") sendfile() could no longer send data
from a real file to a pipe, breaking for example certain cgit
setups (e.g. when running behind fcgiwrap), because in this
case cgit will try to do exactly this: sendfile() to a pipe.
Fix this by using iter_file_splice_write for the splice_write
method of pipes, as suggested by Christoph.
Cc: stable@vger.kernel.org
Fixes: 36e2c7421f ("fs: don't allow splice read/write without explicit ops")
Suggested-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a9c72ad4c upstream.
The verifier allows ARG_PTR_TO_BTF_ID helper arguments to be NULL, so
helper implementations need to check this before dereferencing them.
This was already fixed for the socket storage helpers but not for task
and inode.
The issue can be reproduced by attaching an LSM program to
inode_rename hook (called when moving files) which tries to get the
inode of the new file without checking for its nullness and then trying
to move an existing file to a new path:
mv existing_file new_file_does_not_exist
The report including the sample program and the steps for reproducing
the bug:
https://lore.kernel.org/bpf/CANaYP3HWkH91SN=wTNO9FL_2ztHfqcXKX38SSE-JJ2voh+vssw@mail.gmail.com
Fixes: 4cf1bc1f10 ("bpf: Implement task local storage")
Fixes: 8ea636848a ("bpf: Implement bpf_local_storage for inodes")
Reported-by: Gilad Reti <gilad.reti@gmail.com>
Signed-off-by: KP Singh <kpsingh@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20210112075525.256820-3-kpsingh@kernel.org
[ just take 1/2 of this patch for 5.10.y - gregkh ]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef4d764c99 upstream.
System takes a very long time to suspend after commit 215a22ed31
("ALSA: hda: Refactor codec PM to use direct-complete optimization"):
[ 90.065964] PM: suspend entry (s2idle)
[ 90.067337] Filesystems sync: 0.001 seconds
[ 90.185758] Freezing user space processes ... (elapsed 0.002 seconds) done.
[ 90.188713] OOM killer disabled.
[ 90.188714] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[ 90.190024] printk: Suspending console(s) (use no_console_suspend to debug)
[ 90.904912] intel_pch_thermal 0000:00:12.0: CPU-PCH is cool [49C], continue to suspend
[ 321.262505] snd_hda_codec_realtek ehdaudio0D0: Unable to sync register 0x2b8000. -5
[ 328.426919] snd_hda_codec_realtek ehdaudio0D0: Unable to sync register 0x2b8000. -5
[ 329.490933] ACPI: EC: interrupt blocked
That commit keeps the codec suspended during the system suspend. However,
mute/micmute LED will clear codec's direct-complete flag by
dpm_clear_superiors_direct_complete().
This doesn't play well with SOF driver. When its runtime resume is
called for system suspend, hda_codec_jack_check() schedules
jackpoll_work which uses snd_hdac_is_power_on() to check whether codec
is suspended. Because the direct-complete path isn't taken,
pm_runtime_disable() isn't called so snd_hdac_is_power_on() returns
false and jackpoll continues to run, and snd_hda_power_up_pm() cannot
power up an already suspended codec in multiple attempts, causes the
long delay on system suspend:
if (dev->power.direct_complete) {
if (pm_runtime_status_suspended(dev)) {
pm_runtime_disable(dev);
if (pm_runtime_status_suspended(dev)) {
pm_dev_dbg(dev, state, "direct-complete ");
goto Complete;
}
pm_runtime_enable(dev);
}
dev->power.direct_complete = false;
}
When direct-complete path is taken, snd_hdac_is_power_on() returns true
and hda_jackpoll_work() is skipped by accident. So this is still not
correct.
If we were to use snd_hdac_is_power_on() in system PM path,
pm_runtime_status_suspended() should be used instead of
pm_runtime_suspended(), otherwise pm_runtime_{enable,disable}() may
change the outcome of snd_hdac_is_power_on().
Because devices suspend in reverse order (i.e. child first), it doesn't
make much sense to resume an already suspended codec from audio
controller. So avoid the issue by making sure jackpoll isn't used in
system PM process.
Fixes: 215a22ed31 ("ALSA: hda: Refactor codec PM to use direct-complete optimization")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20210112181128.1229827-3-kai.heng.feng@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c89dffc70b upstream.
Receiving ACK with a valid SYN cookie, cookie_v4_check() allocates struct
request_sock and then can allocate inet_rsk(req)->ireq_opt. After that,
tcp_v4_syn_recv_sock() allocates struct sock and copies ireq_opt to
inet_sk(sk)->inet_opt. Normally, tcp_v4_syn_recv_sock() inserts the full
socket into ehash and sets NULL to ireq_opt. Otherwise,
tcp_v4_syn_recv_sock() has to reset inet_opt by NULL and free the full
socket.
The commit 01770a1661 ("tcp: fix race condition when creating child
sockets from syncookies") added a new path, in which more than one cores
create full sockets for the same SYN cookie. Currently, the core which
loses the race frees the full socket without resetting inet_opt, resulting
in that both sock_put() and reqsk_put() call kfree() for the same memory:
sock_put
sk_free
__sk_free
sk_destruct
__sk_destruct
sk->sk_destruct/inet_sock_destruct
kfree(rcu_dereference_protected(inet->inet_opt, 1));
reqsk_put
reqsk_free
__reqsk_free
req->rsk_ops->destructor/tcp_v4_reqsk_destructor
kfree(rcu_dereference_protected(inet_rsk(req)->ireq_opt, 1));
Calling kmalloc() between the double kfree() can lead to use-after-free, so
this patch fixes it by setting NULL to inet_opt before sock_put().
As a side note, this kind of issue does not happen for IPv6. This is
because tcp_v6_syn_recv_sock() clones both ipv6_opt and pktopts which
correspond to ireq_opt in IPv4.
Fixes: 01770a1661 ("tcp: fix race condition when creating child sockets from syncookies")
CC: Ricardo Dias <rdias@singlestore.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Reviewed-by: Benjamin Herrenschmidt <benh@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20210118055920.82516-1-kuniyu@amazon.co.jp
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7024f60d65 upstream.
Don't assume dest/source buffers are userspace addresses when manually
copying data for string I/O or MOVS MMIO, as {get,put}_user() will fail
if handed a kernel address and ultimately lead to a kernel panic.
When invoking INSB/OUTSB instructions in kernel space in a
SEV-ES-enabled VM, the kernel crashes with the following message:
"SEV-ES: Unsupported exception in #VC instruction emulation - can't continue"
Handle that case properly.
[ bp: Massage commit message. ]
Fixes: f980f9c31a ("x86/sev-es: Compile early handler code into kernel image")
Signed-off-by: Hyunwook (Wooky) Baek <baekhw@google.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: David Rientjes <rientjes@google.com>
Link: https://lkml.kernel.org/r/20210110071102.2576186-1-baekhw@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9bb48c82ac upstream.
This makes the tty layer use the .write_iter() function instead of the
traditional .write() functionality.
That allows writev(), but more importantly also makes it possible to
enable .splice_write() for ttys, reinstating the "splice to tty"
functionality that was lost in commit 36e2c7421f ("fs: don't allow
splice read/write without explicit ops").
Fixes: 36e2c7421f ("fs: don't allow splice read/write without explicit ops")
Reported-by: Oliver Giles <ohw.giles@gmail.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cf9d052aa6 upstream.
In Linux, if a driver does disable_irq() and later does enable_irq()
on its interrupt, I believe it's expecting these properties:
* If an interrupt was pending when the driver disabled then it will
still be pending after the driver re-enables.
* If an edge-triggered interrupt comes in while an interrupt is
disabled it should assert when the interrupt is re-enabled.
If you think that the above sounds a lot like the disable_irq() and
enable_irq() are supposed to be masking/unmasking the interrupt
instead of disabling/enabling it then you've made an astute
observation. Specifically when talking about interrupts, "mask"
usually means to stop posting interrupts but keep tracking them and
"disable" means to fully shut off interrupt detection. It's
unfortunate that this is so confusing, but presumably this is all the
way it is for historical reasons.
Perhaps more confusing than the above is that, even though clients of
IRQs themselves don't have a way to request mask/unmask
vs. disable/enable calls, IRQ chips themselves can implement both.
...and yet more confusing is that if an IRQ chip implements
disable/enable then they will be called when a client driver calls
disable_irq() / enable_irq().
It does feel like some of the above could be cleared up. However,
without any other core interrupt changes it should be clear that when
an IRQ chip gets a request to "disable" an IRQ that it has to treat it
like a mask of that IRQ.
In any case, after that long interlude you can see that the "unmask
and clear" can break things. Maulik tried to fix it so that we no
longer did "unmask and clear" in commit 71266d9d39 ("pinctrl: qcom:
Move clearing pending IRQ to .irq_request_resources callback"), but it
only handled the PDC case and it had problems (it caused
sc7180-trogdor devices to fail to suspend). Let's fix.
>From my understanding the source of the phantom interrupt in the
were these two things:
1. One that could have been introduced in msm_gpio_irq_set_type()
(only for the non-PDC case).
2. Edges could have been detected when a GPIO was muxed away.
Fixing case #1 is easy. We can just add a clear in
msm_gpio_irq_set_type().
Fixing case #2 is harder. Let's use a concrete example. In
sc7180-trogdor.dtsi we configure the uart3 to have two pinctrl states,
sleep and default, and mux between the two during runtime PM and
system suspend (see geni_se_resources_{on,off}() for more
details). The difference between the sleep and default state is that
the RX pin is muxed to a GPIO during sleep and muxed to the UART
otherwise.
As per Qualcomm, when we mux the pin over to the UART function the PDC
(or the non-PDC interrupt detection logic) is still watching it /
latching edges. These edges don't cause interrupts because the
current code masks the interrupt unless we're entering suspend.
However, as soon as we enter suspend we unmask the interrupt and it's
counted as a wakeup.
Let's deal with the problem like this:
* When we mux away, we'll mask our interrupt. This isn't necessary in
the above case since the client already masked us, but it's a good
idea in general.
* When we mux back will clear any interrupts and unmask.
Fixes: 4b7618fdc7 ("pinctrl: qcom: Add irq_enable callback for msm gpio")
Fixes: 71266d9d39 ("pinctrl: qcom: Move clearing pending IRQ to .irq_request_resources callback")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Maulik Shah <mkshah@codeaurora.org>
Tested-by: Maulik Shah <mkshah@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210114191601.v7.4.I7cf3019783720feb57b958c95c2b684940264cd1@changeid
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4079d35fa4 upstream.
When the Qualcomm pinctrl driver wants to Ack an interrupt, it does a
read-modify-write on the interrupt status register. On some SoCs it
makes sure that the status bit is 1 to "Ack" and on others it makes
sure that the bit is 0 to "Ack". Presumably the first type of
interrupt controller is a "write 1 to clear" type register and the
second just let you directly set the interrupt status register.
As far as I can tell from scanning structure definitions, the
interrupt status bit is always in a register by itself. Thus with
both types of interrupt controllers it is safe to "Ack" interrupts
without doing a read-modify-write. We can do a simple write.
It should be noted that if the interrupt status bit _was_ ever in a
register with other things (like maybe status bits for other GPIOs):
a) For "write 1 clear" type controllers then read-modify-write would
be totally wrong because we'd accidentally end up clearing
interrupts we weren't looking at.
b) For "direct set" type controllers then read-modify-write would also
be wrong because someone setting one of the other bits in the
register might accidentally clear (or set) our interrupt.
I say this simply to show that the current read-modify-write doesn't
provide any sort of "future proofing" of the code. In fact (for
"write 1 clear" controllers) the new code is slightly more "future
proof" since it would allow more than one interrupt status bits to
share a register.
NOTE: this code fixes no bugs--it simply avoids an extra register
read.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Maulik Shah <mkshah@codeaurora.org>
Tested-by: Maulik Shah <mkshah@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210114191601.v7.2.I3635de080604e1feda770591c5563bd6e63dd39d@changeid
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 584b7cfcdc upstream.
Multicast entries in the MAC table use the high bits of the MAC
address to encode the ports that should get the packets. But this port
mask does not work for the CPU port, to receive these packets on the
CPU port the MAC_CPU_COPY flag must be set.
Because of this IPv6 was effectively not working because neighbor
solicitations were never received. This was not apparent before commit
9403c158 (net: mscc: ocelot: support IPv4, IPv6 and plain Ethernet mdb
entries) as the IPv6 entries were broken so all incoming IPv6
multicast was then treated as unknown and flooded on all ports.
To fix this problem rework the ocelot_mact_learn() to set the
MAC_CPU_COPY flag when a multicast entry that target the CPU port is
added. For this we have to read back the ports endcoded in the pseudo
MAC address by the caller. It is not a very nice design but that avoid
changing the callers and should make backporting easier.
Signed-off-by: Alban Bedel <alban.bedel@aerq.com>
Fixes: 9403c158b8 ("net: mscc: ocelot: support IPv4, IPv6 and plain Ethernet mdb entries")
Link: https://lore.kernel.org/r/20210119140638.203374-1-alban.bedel@aerq.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9d9b1ee0b2 upstream.
The TCP session does not terminate with TCP_USER_TIMEOUT when data
remain untransmitted due to zero window.
The number of unanswered zero-window probes (tcp_probes_out) is
reset to zero with incoming acks irrespective of the window size,
as described in tcp_probe_timer():
RFC 1122 4.2.2.17 requires the sender to stay open indefinitely
as long as the receiver continues to respond probes. We support
this by default and reset icsk_probes_out with incoming ACKs.
This counter, however, is the wrong one to be used in calculating the
duration that the window remains closed and data remain untransmitted.
Thanks to Jonathan Maxwell <jmaxwell37@gmail.com> for diagnosing the
actual issue.
In this patch a new timestamp is introduced for the socket in order to
track the elapsed time for the zero-window probes that have not been
answered with any non-zero window ack.
Fixes: 9721e709fa ("tcp: simplify window probe aborting on USER_TIMEOUT")
Reported-by: William McCall <william.mccall@gmail.com>
Co-developed-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Enke Chen <enchen@paloaltonetworks.com>
Reviewed-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20210115223058.GA39267@localhost.localdomain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b160c28548 upstream.
Heiner Kallweit reported that some skbs were sent with
the following invalid GSO properties :
- gso_size > 0
- gso_type == 0
This was triggerring a WARN_ON_ONCE() in rtl8169_tso_csum_v2.
Juerg Haefliger was able to reproduce a similar issue using
a lan78xx NIC and a workload mixing TCP incoming traffic
and forwarded packets.
The problem is that tcp_add_backlog() is writing
over gso_segs and gso_size even if the incoming packet will not
be coalesced to the backlog tail packet.
While skb_try_coalesce() would bail out if tail packet is cloned,
this overwriting would lead to corruptions of other packets
cooked by lan78xx, sharing a common super-packet.
The strategy used by lan78xx is to use a big skb, and split
it into all received packets using skb_clone() to avoid copies.
The drawback of this strategy is that all the small skb share a common
struct skb_shared_info.
This patch rewrites TCP gso_size/gso_segs handling to only
happen on the tail skb, since skb_try_coalesce() made sure
it was not cloned.
Fixes: 4f693b55c3 ("tcp: implement coalescing on backlog queue")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Bisected-by: Juerg Haefliger <juergh@canonical.com>
Tested-by: Juerg Haefliger <juergh@canonical.com>
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209423
Link: https://lore.kernel.org/r/20210119164900.766957-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 79267ae226 upstream.
The blamed commit was too aggressive, and it made ocelot_netdevice_event
react only to network interface events emitted for the ocelot switch
ports.
In fact, only the PRECHANGEUPPER should have had that check.
When we ignore all events that are not for us, we miss the fact that the
upper of the LAG changes, and the bonding interface gets enslaved to a
bridge. This is an operation we could offload under certain conditions.
Fixes: 7afb3e575e ("net: mscc: ocelot: don't handle netdev events for other netdevs")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210118135210.2666246-1-olteanv@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ceed9038b2 upstream.
The multicast route ff00::/8 is created with type RTN_UNICAST:
$ ip -6 -d route
unicast ::1 dev lo proto kernel scope global metric 256 pref medium
unicast fe80::/64 dev eth0 proto kernel scope global metric 256 pref medium
unicast ff00::/8 dev eth0 proto kernel scope global metric 256 pref medium
Set the type to RTN_MULTICAST which is more appropriate.
Fixes: e8478e80e5 ("net/ipv6: Save route type in rt6_info")
Signed-off-by: Matteo Croce <mcroce@microsoft.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a826b04303 upstream.
The ff00::/8 multicast route is created without specifying the fc_protocol
field, so the default RTPROT_BOOT value is used:
$ ip -6 -d route
unicast ::1 dev lo proto kernel scope global metric 256 pref medium
unicast fe80::/64 dev eth0 proto kernel scope global metric 256 pref medium
unicast ff00::/8 dev eth0 proto boot scope global metric 256 pref medium
As the documentation says, this value identifies routes installed during
boot, but the route is created when interface is set up.
Change the value to RTPROT_KERNEL which is a better value.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Matteo Croce <mcroce@microsoft.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d2b51b008 upstream.
udp_v4_early_demux() is the only function that calls
ip_mc_validate_source() with a TOS that hasn't been masked with
IPTOS_RT_MASK.
This results in different behaviours for incoming multicast UDPv4
packets, depending on if ip_mc_validate_source() is called from the
early-demux path (udp_v4_early_demux) or from the regular input path
(ip_route_input_noref).
ECN would normally not be used with UDP multicast packets, so the
practical consequences should be limited on that side. However,
IPTOS_RT_MASK is used to also masks the TOS' high order bits, to align
with the non-early-demux path behaviour.
Reproducer:
Setup two netns, connected with veth:
$ ip netns add ns0
$ ip netns add ns1
$ ip -netns ns0 link set dev lo up
$ ip -netns ns1 link set dev lo up
$ ip link add name veth01 netns ns0 type veth peer name veth10 netns ns1
$ ip -netns ns0 link set dev veth01 up
$ ip -netns ns1 link set dev veth10 up
$ ip -netns ns0 address add 192.0.2.10 peer 192.0.2.11/32 dev veth01
$ ip -netns ns1 address add 192.0.2.11 peer 192.0.2.10/32 dev veth10
In ns0, add route to multicast address 224.0.2.0/24 using source
address 198.51.100.10:
$ ip -netns ns0 address add 198.51.100.10/32 dev lo
$ ip -netns ns0 route add 224.0.2.0/24 dev veth01 src 198.51.100.10
In ns1, define route to 198.51.100.10, only for packets with TOS 4:
$ ip -netns ns1 route add 198.51.100.10/32 tos 4 dev veth10
Also activate rp_filter in ns1, so that incoming packets not matching
the above route get dropped:
$ ip netns exec ns1 sysctl -wq net.ipv4.conf.veth10.rp_filter=1
Now try to receive packets on 224.0.2.11:
$ ip netns exec ns1 socat UDP-RECVFROM:1111,ip-add-membership=224.0.2.11:veth10,ignoreeof -
In ns0, send packet to 224.0.2.11 with TOS 4 and ECT(0) (that is,
tos 6 for socat):
$ echo test0 | ip netns exec ns0 socat - UDP-DATAGRAM:224.0.2.11:1111,bind=:1111,tos=6
The "test0" message is properly received by socat in ns1, because
early-demux has no cached dst to use, so source address validation
is done by ip_route_input_mc(), which receives a TOS that has the
ECN bits masked.
Now send another packet to 224.0.2.11, still with TOS 4 and ECT(0):
$ echo test1 | ip netns exec ns0 socat - UDP-DATAGRAM:224.0.2.11:1111,bind=:1111,tos=6
The "test1" message isn't received by socat in ns1, because, now,
early-demux has a cached dst to use and calls ip_mc_validate_source()
immediately, without masking the ECN bits.
Fixes: bc044e8db7 ("udp: perform source validation for mcast early demux")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9c30ae8398 upstream.
The previous commit 32efcc06d2 ("tcp: export count for rehash attempts")
would mis-account rehashing SNMP and socket stats:
a. During handshake of an active open, only counts the first
SYN timeout
b. After handshake of passive and active open, stop updating
after (roughly) TCP_RETRIES1 recurring RTOs
c. After the socket aborts, over count timeout_rehash by 1
This patch fixes this by checking the rehash result from sk_rethink_txhash.
Fixes: 32efcc06d2 ("tcp: export count for rehash attempts")
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Link: https://lore.kernel.org/r/20210119192619.1848270-1-ycheng@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a11a496ee6 upstream.
During testing kasan_populate_early_shadow and kasan_remove_zero_shadow,
if the shadow start and end address in kasan_remove_zero_shadow() is not
aligned to PMD_SIZE, the remain unaligned PTE won't be removed.
In the test case for kasan_remove_zero_shadow():
shadow_start: 0xffffffb802000000, shadow end: 0xffffffbfbe000000
3-level page table:
PUD_SIZE: 0x40000000 PMD_SIZE: 0x200000 PAGE_SIZE: 4K
0xffffffbf80000000 ~ 0xffffffbfbdf80000 will not be removed because in
kasan_remove_pud_table(), kasan_pmd_table(*pud) is true but the next
address is 0xffffffbfbdf80000 which is not aligned to PUD_SIZE.
In the correct condition, this should fallback to the next level
kasan_remove_pmd_table() but the condition flow always continue to skip
the unaligned part.
Fix by correcting the condition when next and addr are neither aligned.
Link: https://lkml.kernel.org/r/20210103135621.83129-1-lecopzer@gmail.com
Fixes: 0207df4fa1 ("kernel/memremap, kasan: make ZONE_DEVICE with work with KASAN")
Signed-off-by: Lecopzer Chen <lecopzer.chen@mediatek.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: YJ Chiang <yj.chiang@mediatek.com>
Cc: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66c556025d upstream.
Commit 3226b158e6 ("net: avoid 32 x truesize under-estimation for
tiny skbs") ensured that skbs with data size lower than 1025 bytes
will be kmalloc'ed to avoid excessive page cache fragmentation and
memory consumption.
However, the fix adressed only __napi_alloc_skb() (primarily for
virtio_net and napi_get_frags()), but the issue can still be achieved
through __netdev_alloc_skb(), which is still used by several drivers.
Drivers often allocate a tiny skb for headers and place the rest of
the frame to frags (so-called copybreak).
Mirror the condition to __netdev_alloc_skb() to handle this case too.
Since v1 [0]:
- fix "Fixes:" tag;
- refine commit message (mention copybreak usecase).
[0] https://lore.kernel.org/netdev/20210114235423.232737-1-alobakin@pm.me
Fixes: a1c7fff7e1 ("net: netdev_alloc_skb() use build_skb()")
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Link: https://lore.kernel.org/r/20210115150354.85967-1-alobakin@pm.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9778448175 upstream.
The allocated page is not released if error occurs in
nvm_submit_io_sync_raw(). __free_page() is moved ealier to avoid
possible memory leak issue.
Fixes: aff3fb18f9 ("lightnvm: move bad block and chunk state logic to core")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fa0732168f upstream.
Properly unwind step by step using refactored helpers from nvme_unmap_data
to avoid a potential double dma_unmap on a mapping failure.
Fixes: 7fe07d14f7 ("nvme-pci: merge nvme_free_iod into nvme_unmap_data")
Reported-by: Marc Orr <marcorr@google.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Marc Orr <marcorr@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9275c206f8 upstream.
Split out three helpers from nvme_unmap_data that will allow finer grained
unwinding from nvme_map_data.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Marc Orr <marcorr@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 87fe04367d upstream.
mv88e6xxx_port_vlan_join checks whether the VTU already contains an
entry for the given vid (via mv88e6xxx_vtu_getnext), and if so, merely
changes the relevant .member[] element and loads the updated entry
into the VTU.
However, at least for the mv88e6250, the on-stack struct
mv88e6xxx_vtu_entry vlan never has its .state[] array explicitly
initialized, neither in mv88e6xxx_port_vlan_join() nor inside the
getnext implementation. So the new entry has random garbage for the
STU bits, breaking VLAN filtering.
When the VTU entry is initially created, those bits are all zero, and
we should make sure to keep them that way when the entry is updated.
Fixes: 92307069a9 (net: dsa: mv88e6xxx: Avoid VTU corruption on 6097)
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Tobias Waldekranz <tobias@waldekranz.com>
Tested-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9c25af2502 upstream.
The earlier commit to fix runtime PM in case i915 init fails,
introduces a possibility to hit a page fault.
snd_hdac_ext_bus_device_exit() is designed to be called from
dev.release(). Calling it outside device reference counting, is
not safe and may lead to calling the device_exit() function
twice. Additionally, as part of ext_bus_device_init(), the device
is also registered with snd_hdac_device_register(). Thus before
calling device_exit(), the device must be removed from device
hierarchy first.
Fix the issue by rolling back init actions by calling
hdac_device_unregister() and then releasing device with put_device().
This matches with existing code in hdac-ext module.
To complete the fix, add handling for the case where
hda_codec_load_module() returns -ENODEV, and clean up the hdac_ext
resources also in this case.
In future work, hdac-ext interface should be extended to allow clients
more flexibility to handle the life-cycle of individual devices, beyond
just the current snd_hdac_ext_bus_device_remove(), which removes all
devices.
BugLink: https://github.com/thesofproject/linux/issues/2646
Reported-by: Jaroslav Kysela <perex@perex.cz>
Fixes: 6c63c954e1 ("ASoC: SOF: fix a runtime pm issue in SOF when HDMI codec doesn't work")
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Libin Yang <libin.yang@intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Link: https://lore.kernel.org/r/20210113150715.3992635-1-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f477a538c1 upstream.
When G2_DMA is enabled and SH_DMA is disabled, it results in the following
Kbuild warning:
WARNING: unmet direct dependencies detected for SH_DMA_API
Depends on [n]: SH_DMA [=n]
Selected by [y]:
- G2_DMA [=y] && SH_DREAMCAST [=y]
The reason is that G2_DMA selects SH_DMA_API without depending on or
selecting SH_DMA while SH_DMA_API depends on SH_DMA.
When G2_DMA was first introduced with commit 40f49e7ed7
("sh: dma: Make G2 DMA configurable."), this wasn't an issue since
SH_DMA_API didn't have such dependency, and this way was the only way to
enable it since SH_DMA_API was non-visible. However, later SH_DMA_API was
made visible and dependent on SH_DMA with commit d8902adcc1
("dmaengine: sh: Add Support SuperH DMA Engine driver").
Let G2_DMA depend on SH_DMA_API instead to avoid Kbuild issues.
Fixes: d8902adcc1 ("dmaengine: sh: Add Support SuperH DMA Engine driver")
Signed-off-by: Necip Fazil Yildiran <fazilyildiran@gmail.com>
Signed-off-by: Rich Felker <dalias@libc.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b3c95d0bdb upstream.
When crtc state need_modeset is true it is not necessary
it is going to be a real modeset, it can turns to be a
fastset instead of modeset.
This turns content protection property to be DESIRED and hdcp
update_pipe left with property to be in DESIRED state but
actual hdcp->value was ENABLED.
This issue is caught with DP MST setup, where we have multiple
connector in same DP_MST topology. When disabling HDCP on one of
DP MST connector leads to set the crtc state need_modeset to true
for all other crtc driving the other DP-MST topology connectors.
This turns up other DP MST connectors CP property to be DESIRED
despite the actual hdcp->value is ENABLED.
Above scenario fails the DP MST HDCP IGT test, disabling HDCP on
one MST stream should not cause to disable HDCP on another MST
stream on same DP MST topology.
v2:
- Fixed connector->base.registration_state == DRM_CONNECTOR_REGISTERED
WARN_ON.
v3:
- Commit log improvement. [Uma]
- Added a comment before scheduling prop_work. [Uma]
Fixes: 33f9a623bf ("drm/i915/hdcp: Update CP as per the kernel internal state")
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-2-anshuman.gupta@intel.com
(cherry picked from commit d276e16702)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1fc7c1ef37 upstream.
Some platforms, such as mips64, don't map __u64 to long long unsigned
int so using %llu produces a warning:
gpio-watch.c: In function ‘main’:
gpio-watch.c:89:30: warning: format ‘%llu’ expects argument of type ‘long long unsigned int’, but argument 4 has type ‘__u64’ {aka ‘long unsigned int’} [-Wformat=]
89 | printf("line %u: %s at %llu\n",
| ~~~^
| |
| long long unsigned int
| %lu
90 | chg.info.offset, event, chg.timestamp_ns);
| ~~~~~~~~~~~~~~~~
| |
| __u64 {aka long unsigned int}
Replace the %llu with PRIu64 and cast the argument to uint64_t.
Fixes: 33f0c47b8f ("tools: gpio: implement gpio-watch")
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2fe7c2f994 upstream.
Some platforms, such as mips64, don't map __u64 to long long unsigned
int so using %llu produces a warning:
gpio-event-mon.c:110:37: warning: format ‘%llu’ expects argument of type ‘long long unsigned int’, but argument 3 has type ‘__u64’ {aka ‘long unsigned int’} [-Wformat=]
110 | fprintf(stdout, "GPIO EVENT at %llu on line %d (%d|%d) ",
| ~~~^
| |
| long long unsigned int
| %lu
111 | event.timestamp_ns, event.offset, event.line_seqno,
| ~~~~~~~~~~~~~~~~~~
| |
| __u64 {aka long unsigned int}
Replace the %llu with PRIu64 and cast the argument to uint64_t.
Fixes: 03fd11b033 ("tools/gpio/gpio-event-mon: fix warning")
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e5a6266fb upstream.
RT_TOS() only masks one of the two ECN bits. Therefore rpfilter_mt()
treats Not-ECT or ECT(1) packets in a different way than those with
ECT(0) or CE.
Reproducer:
Create two netns, connected with a veth:
$ ip netns add ns0
$ ip netns add ns1
$ ip link add name veth01 netns ns0 type veth peer name veth10 netns ns1
$ ip -netns ns0 link set dev veth01 up
$ ip -netns ns1 link set dev veth10 up
$ ip -netns ns0 address add 192.0.2.10/32 dev veth01
$ ip -netns ns1 address add 192.0.2.11/32 dev veth10
Add a route to ns1 in ns0:
$ ip -netns ns0 route add 192.0.2.11/32 dev veth01
In ns1, only packets with TOS 4 can be routed to ns0:
$ ip -netns ns1 route add 192.0.2.10/32 tos 4 dev veth10
Ping from ns0 to ns1 works regardless of the ECN bits, as long as TOS
is 4:
$ ip netns exec ns0 ping -Q 4 192.0.2.11 # TOS 4, Not-ECT
... 0% packet loss ...
$ ip netns exec ns0 ping -Q 5 192.0.2.11 # TOS 4, ECT(1)
... 0% packet loss ...
$ ip netns exec ns0 ping -Q 6 192.0.2.11 # TOS 4, ECT(0)
... 0% packet loss ...
$ ip netns exec ns0 ping -Q 7 192.0.2.11 # TOS 4, CE
... 0% packet loss ...
Now use iptable's rpfilter module in ns1:
$ ip netns exec ns1 iptables-legacy -t raw -A PREROUTING -m rpfilter --invert -j DROP
Not-ECT and ECT(1) packets still pass:
$ ip netns exec ns0 ping -Q 4 192.0.2.11 # TOS 4, Not-ECT
... 0% packet loss ...
$ ip netns exec ns0 ping -Q 5 192.0.2.11 # TOS 4, ECT(1)
... 0% packet loss ...
But ECT(0) and ECN packets are dropped:
$ ip netns exec ns0 ping -Q 6 192.0.2.11 # TOS 4, ECT(0)
... 100% packet loss ...
$ ip netns exec ns0 ping -Q 7 192.0.2.11 # TOS 4, CE
... 100% packet loss ...
After this patch, rpfilter doesn't drop ECT(0) and CE packets anymore.
Fixes: 8f97339d3f ("netfilter: add ipv4 reverse path filter match")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0e634efd85 upstream.
Rename intel_dp_sink_dpms() to intel_dp_set_power()
so one doesn't always have to convert from the DPMS
enum values to the actual DP D-states.
Also when dealing with a branch device this has nothing to
do with any sink, so the old name was nonsense anyway.
Also adjust the debug message accordingly, and pimp it
with the standard encoder id+name thing.
Trivial bits done with cocci:
@@
expression DP;
@@
(
- intel_dp_sink_dpms(DP, DRM_MODE_DPMS_OFF)
+ intel_dp_set_power(DP, DP_SET_POWER_D3)
|
- intel_dp_sink_dpms(DP, DRM_MODE_DPMS_ON)
+ intel_dp_set_power(DP, DP_SET_POWER_D0)
)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201016194800.25581-2-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d1cf435e2 upstream.
If the device passed as the target (second argument) to
device_is_dependent() is not completely registered (that is, it has
been initialized, but not added yet), but the parent pointer of it
is set, it may be missing from the list of the parent's children
and device_for_each_child() called by device_is_dependent() cannot
be relied on to catch that dependency.
For this reason, modify device_is_dependent() to check the ancestors
of the target device by following its parent pointer in addition to
the device_for_each_child() walk.
Fixes: 9ed9895370 ("driver core: Functional dependencies tracking support")
Reported-by: Stephan Gerhold <stephan@gerhold.net>
Tested-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Saravana Kannan <saravanak@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/17705994.d592GUb2YH@kreacher
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0243bbd5d upstream.
There will be memory leak if driver probe failed. Trace as below:
backtrace:
[<000000002415258f>] kmemleak_alloc+0x3c/0x50
[<00000000f447ebe4>] __kmalloc+0x208/0x530
[<0000000048bc7b3a>] of_dma_get_range+0xe4/0x1b0
[<0000000041e39065>] of_dma_configure_id+0x58/0x27c
[<000000006356866a>] platform_dma_configure+0x2c/0x40
......
[<000000000afcf9b5>] ret_from_fork+0x10/0x3c
This issue is introduced by commit e0d072782c73("dma-mapping:
introduce DMA range map, supplanting dma_pfn_offset "). It doesn't
free dma_range_map when driver probe failed and cause above
memory leak. So, add code to free it in error path.
Fixes: e0d072782c ("dma-mapping: introduce DMA range map, supplanting dma_pfn_offset ")
Cc: stable@vger.kernel.org
Signed-off-by: Meng Li <Meng.Li@windriver.com>
Link: https://lore.kernel.org/r/20210105070927.14968-1-Meng.Li@windriver.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit da7e0c3c29 upstream.
Occasionally, we are seeing some SuperSpeed devices resumes right after
being directed to U3. This commits add 500us delay to ensure LFPS
detector is disabled before sending ACK to firmware.
[ 16.099363] tegra-xusb 70090000.usb: entering ELPG
[ 16.104343] tegra-xusb 70090000.usb: 2-1 isn't suspended: 0x0c001203
[ 16.114576] tegra-xusb 70090000.usb: not all ports suspended: -16
[ 16.120789] tegra-xusb 70090000.usb: entering ELPG failed
The register write passes through a few flop stages of 32KHz clock domain.
NVIDIA ASIC designer reviewed RTL and suggests 500us delay.
Cc: stable@vger.kernel.org
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210115161907.2875631-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 576667bad3 upstream.
Once the command ring doorbell is rung the xHC controller will parse all
command TRBs on the command ring that have the cycle bit set properly.
If the driver just started writing the next command TRB to the ring when
hardware finished the previous TRB, then HW might fetch an incomplete TRB
as long as its cycle bit set correctly.
A command TRB is 16 bytes (128 bits) long.
Driver writes the command TRB in four 32 bit chunks, with the chunk
containing the cycle bit last. This does however not guarantee that
chunks actually get written in that order.
This was detected in stress testing when canceling URBs with several
connected USB devices.
Two consecutive "Set TR Dequeue pointer" commands got queued right
after each other, and the second one was only partially written when
the controller parsed it, causing the dequeue pointer to be set
to bogus values. This was seen as error messages:
"Mismatch between completed Set TR Deq Ptr command & xHCI internal state"
Solution is to add a write memory barrier before writing the cycle bit.
Cc: <stable@vger.kernel.org>
Tested-by: Ross Zwisler <zwisler@google.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210115161907.2875631-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2ef02b846e upstream.
The cdns3 core device is populated by calling of_platform_populate,
the flag OF_POPULATED is set for core device node, if this flag
is not cleared, when calling of_platform_populate the second time
after loading parent module again, the OF code will not try to create
platform device for core device.
To fix it, it uses of_platform_depopulate to depopulate the core
device which the parent created, and the flag OF_POPULATED for
core device node will be cleared accordingly.
Cc: <stable@vger.kernel.org>
Fixes: 1e056efab9 ("usb: cdns3: add NXP imx8qm glue layer")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e6aa61d81 upstream.
Commit c318840fb2 ("USB: Gadget: dummy-hcd: Fix shift-out-of-bounds
bug") messed up the way dummy-hcd handles requests to turn on the
RESET port feature (I didn't notice that the original switch case
ended with a fallthrough). The call to set_link_state() was
inadvertently removed, as was the code to set the USB_PORT_STAT_RESET
flag when the speed is USB2.
In addition, the original code never checked whether the port was
connected before handling the port-reset request. There was a check
for the port being powered, but it was removed by that commit! In
practice this doesn't matter much because the kernel doesn't try to
reset disconnected ports, but it's still bad form.
This patch fixes these problems by changing the fallthrough to break,
adding back in the missing set_link_state() call, setting the
port-reset status flag, adding a port-is-connected test, and removing
a redundant assignment statement.
Fixes: c318840fb2 ("USB: Gadget: dummy-hcd: Fix shift-out-of-bounds bug")
CC: <stable@vger.kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20210113194510.GA1290698@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 643a4df7fe upstream.
The system that use Synopsys USB host controllers goes to suspend
when using USB audio player. This causes the USB host controller
continuous send interrupt signal to system, When the number of
interrupts exceeds 100000, the system will forcibly close the
interrupts and output a calltrace error.
When the system goes to suspend, the last interrupt is reported to
the driver. At this time, the system has set the state to suspend.
This causes the last interrupt to not be processed by the system and
not clear the interrupt flag. This uncleared interrupt flag constantly
triggers new interrupt event. This causing the driver to receive more
than 100,000 interrupts, which causes the system to forcibly close the
interrupt report and report the calltrace error.
so, when the driver goes to sleep and changes the system state to
suspend, the interrupt flag needs to be cleared.
Signed-off-by: Longfang Liu <liulongfang@huawei.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/1610416647-45774-1-git-send-email-liulongfang@huawei.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54ca955b5a upstream.
Commit c685af1108 ("serial: mvebu-uart: fix tx lost characters") fixed tx
lost characters at low baud rates but started causing tx lost characters
when kernel is going to power off or reboot.
TX_EMP tells us when transmit queue is empty therefore all characters were
transmitted. TX_RDY tells us when CPU can send a new character.
Therefore we need to use different check prior transmitting new character
and different check after all characters were sent.
This patch splits polling code into two functions: wait_for_xmitr() which
waits for TX_RDY and wait_for_xmite() which waits for TX_EMP.
When rebooting A3720 platform without this patch on UART is print only:
[ 42.699�
And with this patch on UART is full output:
[ 39.530216] reboot: Restarting system
Fixes: c685af1108 ("serial: mvebu-uart: fix tx lost characters")
Signed-off-by: Pali Rohár <pali@kernel.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201223191931.18343-1-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a173346bd upstream.
Sockets and other non-regular files may actually expect short reads to
happen, don't retry reads for them. Because non-reg files don't set
FMODE_BUF_RASYNC and so it won't do second/retry do_read, we can filter
out those cases after first do_read() attempt with ret>0.
Cc: stable@vger.kernel.org # 5.9+
Suggested-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 607ec89ed1 upstream.
IORING_OP_CLOSE is special in terms of cancelation, since it has an
intermediate state where we've removed the file descriptor but hasn't
closed the file yet. For that reason, it's currently marked with
IO_WQ_WORK_NO_CANCEL to prevent cancelation. This ensures that the op
is always run even if canceled, to prevent leaving us with a live file
but an fd that is gone. However, with SQPOLL, since a cancel request
doesn't carry any resources on behalf of the request being canceled, if
we cancel before any of the close op has been run, we can end up with
io-wq not having the ->files assigned. This can result in the following
oops reported by Joseph:
BUG: kernel NULL pointer dereference, address: 00000000000000d8
PGD 800000010b76f067 P4D 800000010b76f067 PUD 10b462067 PMD 0
Oops: 0000 [#1] SMP PTI
CPU: 1 PID: 1788 Comm: io_uring-sq Not tainted 5.11.0-rc4 #1
Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
RIP: 0010:__lock_acquire+0x19d/0x18c0
Code: 00 00 8b 1d fd 56 dd 08 85 db 0f 85 43 05 00 00 48 c7 c6 98 7b 95 82 48 c7 c7 57 96 93 82 e8 9a bc f5 ff 0f 0b e9 2b 05 00 00 <48> 81 3f c0 ca 67 8a b8 00 00 00 00 41 0f 45 c0 89 04 24 e9 81 fe
RSP: 0018:ffffc90001933828 EFLAGS: 00010002
RAX: 0000000000000001 RBX: 0000000000000001 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 00000000000000d8
RBP: 0000000000000246 R08: 0000000000000001 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000000
R13: 0000000000000000 R14: ffff888106e8a140 R15: 00000000000000d8
FS: 0000000000000000(0000) GS:ffff88813bd00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000000000d8 CR3: 0000000106efa004 CR4: 00000000003706e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
lock_acquire+0x31a/0x440
? close_fd_get_file+0x39/0x160
? __lock_acquire+0x647/0x18c0
_raw_spin_lock+0x2c/0x40
? close_fd_get_file+0x39/0x160
close_fd_get_file+0x39/0x160
io_issue_sqe+0x1334/0x14e0
? lock_acquire+0x31a/0x440
? __io_free_req+0xcf/0x2e0
? __io_free_req+0x175/0x2e0
? find_held_lock+0x28/0xb0
? io_wq_submit_work+0x7f/0x240
io_wq_submit_work+0x7f/0x240
io_wq_cancel_cb+0x161/0x580
? io_wqe_wake_worker+0x114/0x360
? io_uring_get_socket+0x40/0x40
io_async_find_and_cancel+0x3b/0x140
io_issue_sqe+0xbe1/0x14e0
? __lock_acquire+0x647/0x18c0
? __io_queue_sqe+0x10b/0x5f0
__io_queue_sqe+0x10b/0x5f0
? io_req_prep+0xdb/0x1150
? mark_held_locks+0x6d/0xb0
? mark_held_locks+0x6d/0xb0
? io_queue_sqe+0x235/0x4b0
io_queue_sqe+0x235/0x4b0
io_submit_sqes+0xd7e/0x12a0
? _raw_spin_unlock_irq+0x24/0x30
? io_sq_thread+0x3ae/0x940
io_sq_thread+0x207/0x940
? do_wait_intr_irq+0xc0/0xc0
? __ia32_sys_io_uring_enter+0x650/0x650
kthread+0x134/0x180
? kthread_create_worker_on_cpu+0x90/0x90
ret_from_fork+0x1f/0x30
Fix this by moving the IO_WQ_WORK_NO_CANCEL until _after_ we've modified
the fdtable. Canceling before this point is totally fine, and running
it in the io-wq context _after_ that point is also fine.
For 5.12, we'll handle this internally and get rid of the no-cancel
flag, as IORING_OP_CLOSE is the only user of it.
Cc: stable@vger.kernel.org
Fixes: b5dba59e0c ("io_uring: add support for IORING_OP_CLOSE")
Reported-by: "Abaci <abaci@linux.alibaba.com>"
Reviewed-and-tested-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c93cc9e16d upstream.
If we're freeing/finishing iopoll requests, ensure we check if the task
is in idling in terms of cancelation. Otherwise we could end up waiting
forever in __io_uring_task_cancel() if the task has active iopoll
requests that need cancelation.
Cc: stable@vger.kernel.org # 5.9+
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bde9cfa3af upstream.
Patch series "mm: fix initialization of struct page for holes in memory layout", v3.
Commit 73a6e474cb ("mm: memmap_init: iterate over memblock regions
rather that check each PFN") exposed several issues with the memory map
initialization and these patches fix those issues.
Initially there were crashes during compaction that Qian Cai reported
back in April [1]. It seemed back then that the problem was fixed, but
a few weeks ago Andrea Arcangeli hit the same bug [2] and there was an
additional discussion at [3].
[1] https://lore.kernel.org/lkml/8C537EB7-85EE-4DCF-943E-3CC0ED0DF56D@lca.pw
[2] https://lore.kernel.org/lkml/20201121194506.13464-1-aarcange@redhat.com
[3] https://lore.kernel.org/mm-commits/20201206005401.qKuAVgOXr%akpm@linux-foundation.org
This patch (of 2):
The first 4Kb of memory is a BIOS owned area and to avoid its allocation
for the kernel it was not listed in e820 tables as memory. As the result,
pfn 0 was never recognised by the generic memory management and it is not
a part of neither node 0 nor ZONE_DMA.
If set_pfnblock_flags_mask() would be ever called for the pageblock
corresponding to the first 2Mbytes of memory, having pfn 0 outside of
ZONE_DMA would trigger
VM_BUG_ON_PAGE(!zone_spans_pfn(page_zone(page), pfn), page);
Along with reserving the first 4Kb in e820 tables, several first pages are
reserved with memblock in several places during setup_arch(). These
reservations are enough to ensure the kernel does not touch the BIOS area
and it is not necessary to remove E820_TYPE_RAM for pfn 0.
Remove the update of e820 table that changes the type of pfn 0 and move
the comment describing why it was done to trim_low_memory_range() that
reserves the beginning of the memory.
Link: https://lkml.kernel.org/r/20210111194017.22696-2-rppt@kernel.org
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Hildenbrand <david@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Qian Cai <cai@lca.pw>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e45122893a upstream.
Currently, requesting kernel FPU access doesn't distinguish which parts of
the extended ("FPU") state are needed. This is nice for simplicity, but
there are a few cases in which it's suboptimal:
- The vast majority of in-kernel FPU users want XMM/YMM/ZMM state but do
not use legacy 387 state. These users want MXCSR initialized but don't
care about the FPU control word. Skipping FNINIT would save time.
(Empirically, FNINIT is several times slower than LDMXCSR.)
- Code that wants MMX doesn't want or need MXCSR initialized.
_mmx_memcpy(), for example, can run before CR4.OSFXSR gets set, and
initializing MXCSR will fail because LDMXCSR generates an #UD when the
aforementioned CR4 bit is not set.
- Any future in-kernel users of XFD (eXtended Feature Disable)-capable
dynamic states will need special handling.
Add a more specific API that allows callers to specify exactly what they
want.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Tested-by: Krzysztof Piotr Olędzki <ole@ans.pl>
Link: https://lkml.kernel.org/r/aff1cac8b8fc7ee900cf73e8f2369966621b053f.1611205691.git.luto@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 599b3063ad upstream.
Since commit 5556797662 ("genirq/irqdomain: Allow partial trimming of
irq_data hierarchy") the irq_data chain is valided.
The irq_domain_trim_hierarchy() function doesn't consider the irq + ipi
domain hierarchy as valid, since the ipi domain has the irq domain set
as parent, but the parent domain has no chip set. Hence the boot ends in
a kernel panic.
Set the chip for the parent domain as it is done in the mips gic irq
driver, to have a valid irq_data chain.
Fixes: 3838a547fd ("irqchip: mips-cpu: Introduce IPI IRQ domain support")
Cc: <stable@vger.kernel.org> # v5.10+
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210107213603.1637781-1-dev@kresin.me
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 214a5ea081 upstream.
RHBZ 1848178
The original intent of returning an error in this function
in the patch:
"CIFS: Mask off signals when sending SMB packets"
was to avoid interrupting packet send in the middle of
sending the data (and thus breaking an SMB connection),
but we also don't want to fail the request for non-fatal
signals even before we have had a chance to try to
send it (the reported problem could be reproduced e.g.
by exiting a child process when the parent process was in
the midst of calling futimens to update a file's timestamps).
In addition, since the signal may remain pending when we enter the
sending loop, we may end up not sending the whole packet before
TCP buffers become full. In this case the code returns -EINTR
but what we need here is to return -ERESTARTSYS instead to
allow system calls to be restarted.
Fixes: b30c74c73c ("CIFS: Mask off signals when sending SMB packets")
Cc: stable@vger.kernel.org # v5.1+
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 08685be776 upstream.
The L1D flush fallback functions are not recoverable vs interrupts,
yet the scv entry flush runs with MSR[EE]=1. This can result in a
timer (soft-NMI) or MCE or SRESET interrupt hitting here and overwriting
the EXRFI save area, which ends up corrupting userspace registers for
scv return.
Fix this by disabling RI and EE for the scv entry fallback flush.
Fixes: f79643787e ("powerpc/64s: flush L1D on kernel entry")
Cc: stable@vger.kernel.org # 5.9+ which also have flush L1D patch backport
Reported-by: Tulio Magno Quites Machado Filho <tuliom@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210111062408.287092-1-npiggin@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9ecd1d2b30 ]
The I2C_SPRD uses Common Clock Framework thus it cannot be built on
platforms without it (e.g. compile test on MIPS with LANTIQ):
/usr/bin/mips-linux-gnu-ld: drivers/i2c/busses/i2c-sprd.o: in function `sprd_i2c_probe':
i2c-sprd.c:(.text.sprd_i2c_probe+0x254): undefined reference to `clk_set_parent'
Fixes: 4a2d5f663d ("i2c: Enable compile testing for more drivers")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc705fecf3 ]
perf_evlist__set_sid_idx() updates perf_sample_id with the evlist map
index, CPU number and TID. It is passed indexes to the evsel's cpu and
thread maps, but references the evlist's maps instead. That results in
using incorrect CPU numbers on heterogeneous systems. Fix it by using
evsel maps.
The id index (PERF_RECORD_ID_INDEX) is used by AUX area tracing when in
sampling mode. Having an incorrect CPU number causes the trace data to
be attributed to the wrong CPU, and can result in decoder errors because
the trace data is then associated with the wrong process.
Committer notes:
Keep the class prefix convention in the function name, switching from
perf_evlist__set_sid_idx() to perf_evsel__set_sid_idx().
Fixes: 3c659eedad ("perf tools: Add id index")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lore.kernel.org/lkml/20210121125446.11287-1-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b425e24a93 ]
The number of queues can change by other means, rather than ethtool. For
example, attaching an mqprio qdisc with num_tc > 1 leads to creating
multiple sets of TX queues, which may be then destroyed when mqprio is
deleted. If an AF_XDP socket is created while mqprio is active,
dev->_tx[queue_id].pool will be filled, but then real_num_tx_queues may
decrease with deletion of mqprio, which will mean that the pool won't be
NULLed, and a further increase of the number of TX queues may expose a
dangling pointer.
To avoid any potential misbehavior, this commit clears pool for RX and
TX queues, regardless of real_num_*_queues, still taking into
consideration num_*_queues to avoid overflows.
Fixes: 1c1efc2af1 ("xsk: Create and free buffer pool independently from umem")
Fixes: a41b4f3c58 ("xsk: simplify xdp_clear_umem_at_qid implementation")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/bpf/20210118160333.333439-1-maximmi@mellanox.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2b73649cee ]
After hibernation, HDA controller can't be runtime-suspended after
commit 215a22ed31 ("ALSA: hda: Refactor codjc PM to use
direct-complete optimization"), which enables direct-complete for HDA
codec.
The HDA codec driver didn't expect direct-complete will be disabled
after it returns a positive value from prepare() callback. However,
there are some places that PM core can disable direct-complete. For
instance, system hibernation or when codec has subordinates like LEDs.
So if the codec is prepared for direct-complete but PM core still calls
codec's suspend or freeze callback, partially revert the commit and take
the original approach, which uses pm_runtime_force_*() helpers to
ensure PM refcount are balanced. Meanwhile, still keep prepare() and
complete() callbacks to enable direct-complete and request a resume for
jack detection, respectively.
Reported-by: Kenneth R. Crudup <kenny@panix.com>
Fixes: 215a22ed31 ("ALSA: hda: Refactor codec PM to use direct-complete optimization")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20210119152145.346558-1-kai.heng.feng@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d35c9a029a ]
The recently added thermal policy support makes a
hp_wmi_perform_query(0x4c, ...) call on older devices which do not
support thermal policies this causes the following warning to be
logged (seen on a HP Stream x360 Convertible PC 11):
[ 26.805305] hp_wmi: query 0x4c returned error 0x3
Error 0x3 is HPWMI_RET_UNKNOWN_COMMAND error. This commit silences
the warning for unknown-command errors, silencing the new warning.
Cc: Elia Devito <eliadevito@gmail.com>
Fixes: 81c93798ef ("platform/x86: hp-wmi: add support for thermal policy")
Link: https://lore.kernel.org/r/20210114232744.154886-1-hdegoede@redhat.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 070222731b ]
THe HP Stream x360 Convertible PC 11 DSDT has the following VGBS function:
Method (VGBS, 0, Serialized)
{
If ((^^PCI0.LPCB.EC0.ROLS == Zero))
{
VBDS = Zero
}
Else
{
VBDS = Zero
}
Return (VBDS) /* \_SB_.VGBI.VBDS */
}
Which is obviously wrong, because it always returns 0 independent of the
2-in-1 being in laptop or tablet mode. This causes the intel-vbtn driver
to initially report SW_TABLET_MODE = 1 to userspace, which is known to
cause problems when the 2-in-1 is actually in laptop mode.
During earlier testing this turned out to not be a problem because the
2-in-1 would do a Notify(..., 0xCC) or Notify(..., 0xCD) soon after
the intel-vbtn driver loaded, correcting the SW_TABLET_MODE state.
Further testing however has shown that this Notify() soon after the
intel-vbtn driver loads, does not always happen. When the Notify
does not happen, then intel-vbtn reports SW_TABLET_MODE = 1 resulting in
a non-working touchpad.
IOW the tablet-mode reporting is not reliable on this device, so it
should be dropped from the allow-list, fixing the touchpad sometimes
not working.
Fixes: 8169bd3e6e ("platform/x86: intel-vbtn: Switch to an allow-list for SW_TABLET_MODE reporting")
Link: https://lore.kernel.org/r/20210114143432.31750-1-hdegoede@redhat.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 33c74535b0 ]
User-space ALSA matches a card's driver name against an internal list of
aliases in order to select the correct configuration for the system.
When the driver name isn't defined, the match is performed against the
card's name.
With the introduction of RPi4 we now have two HDMI ports with two
distinct audio cards. This is reflected in their names, making them
different from previous RPi versions. With this, ALSA ultimately misses
the board's configuration on RPi4.
In order to avoid this, set "card->driver_name" to "vc4-hdmi"
unanimously.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Fixes: f437bc1ec7 ("drm/vc4: drv: Support BCM2711")
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210115191209.12852-1-nsaenzjulienne@suse.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b2cfa2d1d ]
I2C_SMBUS_BLOCK_MAX defines already the maximum number as defined in the
SMBus 2.0 specs. No reason to add one to it.
Fixes: 886f6f8337 ("i2c: octeon: Support I2C_M_RECV_LEN")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Robert Richter <rric@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a959a9782f ]
sizeof needs to be called on the compat pointer, not the native one.
Fixes: 89cd35c58b ("iov_iter: transparently handle compat iovecs in import_iovec")
Reported-by: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 668af87f99 ]
Counting text lines in a record simply involves counting the number
of newline characters (+1). However, it is searching the full data
block for newline characters, even though the text data can be (and
often is) a subset of that area. Since the extra area in the data
block was never initialized, the result is that extra newlines may
be seen and counted.
Restrict newline searching to the text data length.
Fixes: b6cf8b3f33 ("printk: add lockless ringbuffer")
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Acked-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20210113144234.6545-1-john.ogness@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b79f2dc5ff ]
rounddown_pow_of_two() is undefined when the input is 0. Therefore we need
to avoid it in ib_umem_find_best_pgsz and return 0. Otherwise, it could
result in not rejecting an invalid page size which eventually causes a
kernel oops due to the logical inconsistency.
Fixes: 3361c29e92 ("RDMA/umem: Use simpler logic for ib_umem_find_best_pgsz()")
Link: https://lore.kernel.org/r/20210113121703.559778-2-leon@kernel.org
Signed-off-by: Aharon Landau <aharonl@nvidia.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b335bff64 ]
KASAN reported a slab-out-of-bounds read of size 1 in
kdf_create_vcrat_image_cpu().
This occurs when, for example, when on an x86_64 with a single NUMA node
because kfd_fill_iolink_info_for_cpu() is a no-op, but afterwards the
sub_type_hdr->length, which is out-of-bounds, is read and multiplied by
entries. Fortunately, entries is 0 in this case so the overall
crat_table->length is still correct.
Check if there were any entries before de-referencing sub_type_hdr which
may be pointing to out-of-bounds memory.
Fixes: b7b6c38529 ("drm/amdkfd: Calculate CPU VCRAT size dynamically (v2)")
Suggested-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Jeremy Cline <jcline@redhat.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df06824767 ]
All EL0 returns go via ret_to_user(), which masks IRQs and notifies
lockdep and tracing before calling into do_notify_resume(). Therefore,
there's no need for do_notify_resume() to call trace_hardirqs_off(), and
the comment is stale. The call is simply redundant.
In ret_to_user() we call exit_to_user_mode(), which notifies lockdep and
tracing the IRQs will be enabled in userspace, so there's no need for
el0_svc_common() to call trace_hardirqs_on() before returning. Further,
at the start of ret_to_user() we call trace_hardirqs_off(), so not only
is this redundant, but it is immediately undone.
In addition to being redundant, the trace_hardirqs_on() in
el0_svc_common() leaves lockdep inconsistent with the hardware state,
and is liable to cause issues for any C code or instrumentation
between this and the call to trace_hardirqs_off() which undoes it in
ret_to_user().
This patch removes the redundant tracing calls and associated stale
comments.
Fixes: 23529049c6 ("arm64: entry: fix non-NMI user<->kernel transitions")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Will Deacon <will@kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210107145310.44616-1-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2225a8dda2 ]
This is a bug that causes early crashes in builds with an .exit.text
section smaller than a page and an .init.text section that ends in the
beginning of a physical page (this is kinda random, which might
explain why this wasn't really encountered before).
The init sections are ordered like this:
.init.text
.exit.text
.init.data
Currently, these sections aren't page aligned.
Because the init code might become read-only at runtime and because
the .init.text section can potentially reside on the same physical
page as .init.data, the beginning of .init.data might be mapped
read-only along with .init.text.
Then when the kernel tries to modify a variable in .init.data (like
kthreadd_done, used in kernel_init()) the kernel panics.
To avoid this, make _einittext page aligned and also align .exit.text
to make sure .init.data is always seperated from the text segments.
Fixes: 060ef9d89d ("powerpc32: PAGE_EXEC required for inittext")
Signed-off-by: Ariel Marcovitch <ariel.marcovitch@gmail.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210102201156.10805-1-ariel.marcovitch@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5541075a34 ]
The bpf_tracing_prog_attach error path calls bpf_prog_put
on prog, which causes refcount underflow when it's called
from link_create function.
link_create
prog = bpf_prog_get <-- get
...
tracing_bpf_link_attach(prog..
bpf_tracing_prog_attach(prog..
out_put_prog:
bpf_prog_put(prog); <-- put
if (ret < 0)
bpf_prog_put(prog); <-- put
Removing bpf_prog_put call from bpf_tracing_prog_attach
and making sure its callers call it instead.
Fixes: 4a1e7c0c63 ("bpf: Support attaching freplace programs to multiple attach points")
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210111191650.1241578-1-jolsa@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3828119403 ]
The driver was converted to use the crypto engine helper
but is missing the corresponding Kconfig statement to ensure
it is available:
arm-linux-gnueabi-ld: drivers/crypto/omap-sham.o: in function `omap_sham_probe':
omap-sham.c:(.text+0x374): undefined reference to `crypto_engine_alloc_init'
arm-linux-gnueabi-ld: omap-sham.c:(.text+0x384): undefined reference to `crypto_engine_start'
arm-linux-gnueabi-ld: omap-sham.c:(.text+0x510): undefined reference to `crypto_engine_exit'
arm-linux-gnueabi-ld: drivers/crypto/omap-sham.o: in function `omap_sham_finish_req':
omap-sham.c:(.text+0x98c): undefined reference to `crypto_finalize_hash_request'
arm-linux-gnueabi-ld: omap-sham.c:(.text+0x9a0): undefined reference to `crypto_transfer_hash_request_to_engine'
arm-linux-gnueabi-ld: drivers/crypto/omap-sham.o: in function `omap_sham_update':
omap-sham.c:(.text+0xf24): undefined reference to `crypto_transfer_hash_request_to_engine'
arm-linux-gnueabi-ld: drivers/crypto/omap-sham.o: in function `omap_sham_final':
omap-sham.c:(.text+0x1020): undefined reference to `crypto_transfer_hash_request_to_engine'
Fixes: 133c3d434d ("crypto: omap-sham - convert to use crypto engine")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eeb1b55b6e ]
When non-fatal error like line-reset happens, ufshcd_err_handler() starts
to abort tasks by ufshcd_try_to_abort_task(). When it tries to issue a task
management request, we hit two warnings:
WARNING: CPU: 7 PID: 7 at block/blk-core.c:630 blk_get_request+0x68/0x70
WARNING: CPU: 4 PID: 157 at block/blk-mq-tag.c:82 blk_mq_get_tag+0x438/0x46c
After fixing the above warnings we hit another tm_cmd timeout which may be
caused by unstable controller state:
__ufshcd_issue_tm_cmd: task management cmd 0x80 timed-out
Then, ufshcd_err_handler() enters full reset, and kernel gets stuck. It
turned out ufshcd_print_trs() printed too many messages on console which
requires CPU locks. Likewise hba->silence_err_logs, we need to avoid too
verbose messages. This is actually not an error case.
Link: https://lore.kernel.org/r/20210107185316.788815-3-jaegeuk@kernel.org
Fixes: 69a6c269c0 ("scsi: ufs: Use blk_{get,put}_request() to allocate and free TMFs")
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b112036535 ]
Phil Oester reported that a fix for a possible buffer overrun that I sent
caused a regression that manifests in this output:
Event Message: A PCI parity error was detected on a component at bus 0 device 5 function 0.
Severity: Critical
Message ID: PCI1308
The original code tried to handle the sense data pointer differently when
using 32-bit 64-bit DMA addressing, which would lead to a 32-bit dma_addr_t
value of 0x11223344 to get stored
32-bit kernel: 44 33 22 11 ?? ?? ?? ??
64-bit LE kernel: 44 33 22 11 00 00 00 00
64-bit BE kernel: 00 00 00 00 44 33 22 11
or a 64-bit dma_addr_t value of 0x1122334455667788 to get stored as
32-bit kernel: 88 77 66 55 ?? ?? ?? ??
64-bit kernel: 88 77 66 55 44 33 22 11
In my patch, I tried to ensure that the same value is used on both 32-bit
and 64-bit kernels, and picked what seemed to be the most sensible
combination, storing 32-bit addresses in the first four bytes (as 32-bit
kernels already did), and 64-bit addresses in eight consecutive bytes (as
64-bit kernels already did), but evidently this was incorrect.
Always storing the dma_addr_t pointer as 64-bit little-endian,
i.e. initializing the second four bytes to zero in case of 32-bit
addressing, apparently solved the problem for Phil, and is consistent with
what all 64-bit little-endian machines did before.
I also checked in the history that in previous versions of the code, the
pointer was always in the first four bytes without padding, and that
previous attempts to fix 64-bit user space, big-endian architectures and
64-bit DMA were clearly flawed and seem to have introduced made this worse.
Link: https://lore.kernel.org/r/20210104234137.438275-1-arnd@kernel.org
Fixes: 381d34e376 ("scsi: megaraid_sas: Check user-provided offsets")
Fixes: 107a60dd71 ("scsi: megaraid_sas: Add support for 64bit consistent DMA")
Fixes: 94cd65ddf4 ("[SCSI] megaraid_sas: addded support for big endian architecture")
Fixes: 7b2519afa1 ("[SCSI] megaraid_sas: fix 64 bit sense pointer truncation")
Reported-by: Phil Oester <kernel@linuxace.com>
Tested-by: Phil Oester <kernel@linuxace.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 71008734d2 ]
We're supposed to print the root_key.offset in btrfs_root_name in the
case of a reloc root, not the objectid. Fix this helper to take the key
so we have access to the offset when we need it.
Fixes: 457f1864b5 ("btrfs: pretty print leaked root name")
Reviewed-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ae291cc95 ]
The destruction flow is very complicated here because the cm_id can be
destroyed from the event handler at any time if the device is
hot-removed. This leaves behind a partial ctx with no cm_id in the
xarray, and will let user space leak memory.
Make everything consistent in this flow in all places:
- Return the xarray back to XA_ZERO_ENTRY before beginning any
destruction. The thread that reaches this first is responsible to
kfree, everyone else does nothing.
- Test the xarray during the special hot-removal case to block the
queue_work, this has much simpler locking and doesn't require a
'destroying'
- Fix the ref initialization so that it is only positive if cm_id !=
NULL, then rely on that to guide the destruction process in all cases.
Now the new ucma_destroy_private_ctx() can be called in all places that
want to free the ctx, including all the error unwinds, and none of the
details are missed.
Fixes: a1d33b70db ("RDMA/ucma: Rework how new connections are passed through event delivery")
Link: https://lore.kernel.org/r/20210105111327.230270-1-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e202ad873 ]
The kernel test robot reports the following warning in [1]:
drivers/gpio/gpiolib-cdev.c: In function 'gpio_ioctl':
>>drivers/gpio/gpiolib-cdev.c:1437:1: warning: the frame size of 1040 bytes is larger than 1024 bytes [-Wframe-larger-than=]
Refactor gpio_ioctl() to handle each ioctl in its own helper function
and so reduce the variables stored on the stack to those explicitly
required to service the ioctl at hand.
The lineinfo_get_v1() helper handles both the GPIO_GET_LINEINFO_IOCTL
and GPIO_GET_LINEINFO_WATCH_IOCTL, as per the corresponding v2
implementation - lineinfo_get().
[1] https://lore.kernel.org/lkml/202012270910.VW3qc1ER-lkp@intel.com/
Fixes: aad955842d ("gpiolib: cdev: support GPIO_V2_GET_LINEINFO_IOCTL and GPIO_V2_GET_LINEINFO_WATCH_IOCTL")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 72d78717c6 ]
Ensure that we encode the data payload + padding, and that we truncate
the preallocated buffer to the actual read size.
Fixes: 528b84934e ("NFSD: Add READ_PLUS data support")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e557793799 ]
Linux kernel can only map 1GB of address space for RV32 as the page offset
is set to 0xC0000000. The current description in the Kconfig is confusing
as it indicates that RV32 can support 2GB of physical memory. That is
simply not true for current kernel. In future, a 2GB split support can be
added to allow 2GB physical address space.
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit abb8e86b26 ]
Currently, linux kernel can not use last 4k bytes of addressable space
because IS_ERR_VALUE macro treats those as an error. This will be an issue
for RV32 as any memblock allocator potentially allocate chunk of memory
from the end of DRAM (2GB) leading bad address error even though the
address was technically valid.
Fix this issue by limiting the memblock if available memory spans the
entire address space.
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f010505b78 ]
Right now io_flush_timeouts() checks if the current number of events
is equal to ->timeout.target_seq, but this will miss some timeouts if
there have been more than 1 event added since the last time they were
flushed (possible in io_submit_flush_completions(), for example). Fix
it by recording the last sequence at which timeouts were flushed so
that the number of events seen can be compared to the number of events
needed without overflow.
Signed-off-by: Marcelo Diop-Gonzalez <marcelo827@gmail.com>
Reviewed-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e05e06cd34 ]
Whatever it is that we were doing before doesn't work on Ampere.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 402a89660e ]
This issue has generally been covered up by the presence of additional
expansion ROMs after the ones we're interested in, with header fetches
of subsequent images loading enough of the ROM to hide the issue.
Noticed on GA102, which lacks a type 0x70 image compared to TU102,.
[ 906.364197] nouveau 0000:09:00.0: bios: 00000000: type 00, 65024 bytes
[ 906.381205] nouveau 0000:09:00.0: bios: 0000fe00: type 03, 91648 bytes
[ 906.405213] nouveau 0000:09:00.0: bios: 00026400: type e0, 22016 bytes
[ 906.410984] nouveau 0000:09:00.0: bios: 0002ba00: type e0, 366080 bytes
vs
[ 22.961901] nouveau 0000:09:00.0: bios: 00000000: type 00, 60416 bytes
[ 22.984174] nouveau 0000:09:00.0: bios: 0000ec00: type 03, 71168 bytes
[ 23.010446] nouveau 0000:09:00.0: bios: 00020200: type e0, 48128 bytes
[ 23.028220] nouveau 0000:09:00.0: bios: 0002be00: type e0, 140800 bytes
[ 23.080196] nouveau 0000:09:00.0: bios: 0004e400: type 70, 7168 bytes
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 02ce73b01e ]
[Why]
Find out when we try to disable CRC calculation,
crc generation is still enabled. Main reason is
that dc_stream_configure_crc() will never get
called when the source is AMDGPU_DM_PIPE_CRC_SOURCE_NONE.
[How]
Add checking condition that when source is
AMDGPU_DM_PIPE_CRC_SOURCE_NONE, we should also call
dc_stream_configure_crc() to disable crc calculation.
Also, clean up crc window when disable crc calculation.
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7de843dbaa ]
The Logitech MX Ergo trackball supports HID++ 4.5 over Bluetooth. Add its
product ID to the table so we can get battery monitoring support.
(The hid-logitech-hidpp driver already recognizes it when connected via
a Unifying Receiver.)
[jkosina@suse.cz: fix whitespace damage]
Signed-off-by: Nicholas Miell <nmiell@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d03bb1020 ]
[Why]
The initial purpose of dcn10 pipe split is to support some high
bandwidth mode which requires dispclk greater than max dispclk. By
initial bring up power measurement data, it showed power consumption is
less with pipe split for dcn block. This could be reason for enable pipe
split by default. By battery life measurement of some Chromebooks,
result shows battery life is longer with pipe split disabled.
[How]
Disable pipe split by default. Pipe split could be still enabled when
required dispclk is greater than max dispclk.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f14a5c34d1 ]
psp GFX_CTRL_CMD_ID_CONSUME_CMD different for windows and linux,
according to psp, linux cmds are not correct.
v2: only correct GFX_CTRL_CMD_ID_CONSUME_CMD.
Signed-off-by: Victor Zhao <Victor.Zhao@amd.com>
Reviewed-by: Emily.Deng <Emily.Deng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0983834a83 ]
Ethernet phy VSC8541-01 on HiFive Unleashed has its reset line
connected to a gpio, so enable GPIO driver's required to reset
the phy.
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a0fa9d7270 ]
The GEMGXL_RST line on HiFive Unleashed is pulled low and is
using GPIO number 12. Add these reset-gpio details to dt-node
using which the linux phylib can reset the phy.
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be969b7cfb ]
HiFive unleashed A00 board has VSC8541-01 ethernet phy, this device is
identified as a Revision B device as described in device identification
registers. In order to use this phy in the unmanaged mode, it requires
a specific reset sequence of logical 0-1-0-1 transition on the NRESET pin
as documented here [1].
Currently, the bootloader (fsbl or u-boot-spl) takes care of the phy reset.
If due to some reason the phy device hasn't received the reset by the prior
stages before the linux macb driver comes into the picture, the MACB mii
bus gets probed but the mdio scan fails and is not even able to read the
phy ID registers. It gives an error message:
"libphy: MACB_mii_bus: probed
mdio_bus 10090000.ethernet-ffffffff: MDIO device at address 0 is missing."
Thus adding the device OUI (Organizationally Unique Identifier) to the phy
device node helps to probe the phy device.
[1]: VSC8541-01 datasheet:
https://www.mouser.com/ds/2/523/Microsemi_VSC8541-01_Datasheet_10496_V40-1148034.pdf
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d7746bea9 ]
Only the IPI-related functions in the smp_ops should be conditional
on the vector callback being available. The rest should still happen:
• xen_hvm_smp_prepare_boot_cpu()
This function does two things, both of which should still happen if
there is no vector callback support.
The call to xen_vcpu_setup() for vCPU0 should still happen as it just
sets up the vcpu_info for CPU0. That does happen for the secondary
vCPUs too, from xen_cpu_up_prepare_hvm().
The second thing it does is call xen_init_spinlocks(), which perhaps
counter-intuitively should *also* still be happening in the case
without vector callbacks, so that it can clear its local xen_pvspin
flag and disable the virt_spin_lock_key accordingly.
Checking xen_have_vector_callback in xen_init_spinlocks() itself
would affect PV guests, so set the global nopvspin flag in
xen_hvm_smp_init() instead, when vector callbacks aren't available.
• xen_hvm_smp_prepare_cpus()
This does some IPI-related setup by calling xen_smp_intr_init() and
xen_init_lock_cpu(), which can be made conditional. And it sets the
xen_vcpu_id to XEN_VCPU_ID_INVALID for all possible CPUS, which does
need to happen.
• xen_smp_cpus_done()
This offlines any vCPUs which doesn't fit in the global shared_info
page, if separate vcpu_info placement isn't available. That part also
needs to happen regardless of vector callback support.
• xen_hvm_cpu_die()
This doesn't actually do anything other than commin_cpu_die() right
right now in the !vector_callback case; all three teardown functions
it calls should be no-ops. But to guard against future regressions
it's useful to call it anyway, and for it to explicitly check for
xen_have_vector_callback before calling those additional functions.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/20210106153958.584169-6-dwmw2@infradead.org
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b36b0fe96a ]
It's useful to be able to test non-vector event channel delivery, to make
sure Linux will work properly on older Xen which doesn't have it.
It's also useful for those working on Xen and Xen-compatible hypervisors,
because there are guest kernels still in active use which use PCI INTX
even when vector delivery is available.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/20210106153958.584169-4-dwmw2@infradead.org
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3499ba8198 ]
For a while, event channel notification via the PCI platform device
has been broken, because we attempt to communicate with xenstore before
we even have notifications working, with the xs_reset_watches() call
in xs_init().
We tend to get away with this on Xen versions below 4.0 because we avoid
calling xs_reset_watches() anyway, because xenstore might not cope with
reading a non-existent key. And newer Xen *does* have the vector
callback support, so we rarely fall back to INTX/GSI delivery.
To fix it, clean up a bit of the mess of xs_init() and xenbus_probe()
startup. Call xs_init() directly from xenbus_init() only in the !XS_HVM
case, deferring it to be called from xenbus_probe() in the XS_HVM case
instead.
Then fix up the invocation of xenbus_probe() to happen either from its
device_initcall if the callback is available early enough, or when the
callback is finally set up. This means that the hack of calling
xenbus_probe() from a workqueue after the first interrupt, or directly
from the PCI platform device setup, is no longer needed.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/20210113132606.422794-2-dwmw2@infradead.org
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c35a824c31 ]
With UBSAN enabled and building with clang, there are occasionally
warnings like
WARNING: modpost: vmlinux.o(.text+0xc533ec): Section mismatch in reference from the function arch_atomic64_or() to the variable .init.data:numa_nodes_parsed
The function arch_atomic64_or() references
the variable __initdata numa_nodes_parsed.
This is often because arch_atomic64_or lacks a __initdata
annotation or the annotation of numa_nodes_parsed is wrong.
for functions that end up not being inlined as intended but operating
on __initdata variables. Mark these as __always_inline, along with
the corresponding asm-generic wrappers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210108092024.4034860-1-arnd@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 615d435400 ]
Currently hda on tegra30 fails to open a stream with an input/output error.
For example:
speaker-test -Dhw:0,3 -c 2
speaker-test 1.2.2
Playback device is hw:0,3
Stream parameters are 48000Hz, S16_LE, 2 channels
Using 16 octaves of pink noise
Rate set to 48000Hz (requested 48000Hz)
Buffer size range from 64 to 16384
Period size range from 32 to 8192
Using max buffer size 16384
Periods = 4
was set period_size = 4096
was set buffer_size = 16384
0 - Front Left
Write error: -5,Input/output error
xrun_recovery failed: -5,Input/output error
Transfer failed: Input/output error
The tegra-hda device was introduced in tegra30 but only utilized in
tegra124 until recent chips. Tegra210/186 work only due to a hardware
change. For this reason it is unknown when this issue first manifested.
Discussions with the hardware team show this applies to all current tegra
chips. It has been resolved in the tegra234, which does not have hda
support at this time.
The explanation from the hardware team is this:
Below is the striping formula referenced from HD audio spec.
{ ((num_channels * bits_per_sample) / number of SDOs) >= 8 }
The current issue is seen because Tegra HW has a problem with boundary
condition (= 8) for striping. The reason why it is not seen on
Tegra210/Tegra186 is because it uses max 2SDO lines. Max SDO lines is
read from GCAP register.
For the given stream (channels = 2, bps = 16);
ratio = (channels * bps) / NSDO = 32 / NSDO;
On Tegra30, ratio = 32/4 = 8 (FAIL)
On Tegra210/186, ratio = 32/2 = 16 (PASS)
On Tegra194, ratio = 32/4 = 8 (FAIL) ==> Earlier workaround was
applied for it
If Tegra210/186 is forced to use 4SDO, it fails there as well. So the
behavior is consistent across all these chips.
Applying the fix in [1] universally resolves this issue on tegra30-hda.
Tested on the Ouya game console and the tf201 tablet.
[1] commit 60019d8c65 ("ALSA: hda/tegra: workaround playback failure on
Tegra194")
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Ion Agorria <ion@agorria.com>
Reviewed-by: Sameer Pujar <spujar@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Link: https://lore.kernel.org/r/20210108135913.2421585-3-pgwipeout@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c38e769d5 ]
Battery status is being reported for the Elan touchscreen on ASUS
UX550 laptops despite not having a batter. It always shows either 0 or
1%.
Signed-off-by: Seth Miller <miller.seth@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e400071a80 ]
Tested. The device gets correctly exported to userspace and I can see
mouse and keyboard events.
Signed-off-by: Filipe Laíns <lains@archlinux.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 643437b996 ]
When running is M-Mode (no MMU config), MPIE does not get set. This
results in all syscalls being executed with interrupts disabled as
handle_exception never sets SR_IE as it always sees SR_PIE being
cleared. Fix this by always force enabling interrupts in
handle_syscall when CONFIG_RISCV_M_MODE is enabled.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1f1496a923 ]
Setup the port uartclk in sifive_serial_probe() so that the base baud
rate is correctly printed during device probe instead of always showing
"0". I.e. the probe message is changed from
38000000.serial: ttySIF0 at MMIO 0x38000000 (irq = 1,
base_baud = 0) is a SiFive UART v0
to the correct:
38000000.serial: ttySIF0 at MMIO 0x38000000 (irq = 1,
base_baud = 115200) is a SiFive UART v0
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Acked-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11f4c2e940 ]
If of_clk_init() is not called in time_init(), clock providers defined
in the system device tree are not initialized, resulting in failures for
other devices to initialize due to missing clocks.
Similarly to other architectures and to the default kernel time_init()
implementation, call of_clk_init() before executing timer_probe() in
time_init().
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5cc9002ca ]
The block layer code will split a large zeroout request into multiple bios
and if WRITE SAME is disabled because the storage device reports that it
does not support it (or support the length used), we can get an error
message from the block layer despite the setting of RQF_QUIET on the first
request. This is because more than one request may have already been
submitted.
Fix this by setting RQF_QUIET when BLK_STS_TARGET is returned to fail the
request early, we don't need to log a message because we did not actually
submit the command to the device, and the block layer code will handle the
error by submitting individual write bios.
Link: https://lore.kernel.org/r/20201207221021.28243-1-emilne@redhat.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dfe94d4086 ]
Currently the kexec kernel can panic or hang due to 2 causes:
1) hv_cpu_die() is not called upon kexec, so the hypervisor corrupts the
old VP Assist Pages when the kexec kernel runs. The same issue is fixed
for hibernation in commit 421f090c81 ("x86/hyperv: Suspend/resume the
VP assist page for hibernation"). Now fix it for kexec.
2) hyperv_cleanup() is called too early. In the kexec path, the other CPUs
are stopped in hv_machine_shutdown() -> native_machine_shutdown(), so
between hv_kexec_handler() and native_machine_shutdown(), the other CPUs
can still try to access the hypercall page and cause panic. The workaround
"hv_hypercall_pg = NULL;" in hyperv_cleanup() is unreliabe. Move
hyperv_cleanup() to a better place.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/20201222065541.24312-1-decui@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f7b347acb5 ]
The integrity target relies on skcipher for encryption/decryption, but
certain kernel configurations may not enable CRYPTO_SKCIPHER, leading to
compilation errors due to unresolved symbols. Explicitly select
CRYPTO_SKCIPHER for DM_INTEGRITY, since it is unconditionally dependent
on it.
Signed-off-by: Anthony Iliopoulos <ailiop@suse.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3d6eb6e54 ]
Pointstick and its left/right buttons on HP EliteBook 850 G7 need
multi-input quirk to work correctly.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a85a6a332 ]
Daire Byrne reports a ~50% aggregrate throughput regression on his
Linux NFS server after commit da1661b93b ("SUNRPC: Teach server to
use xprt_sock_sendmsg for socket sends"), which replaced
kernel_send_page() calls in NFSD's socket send path with calls to
sock_sendmsg() using iov_iter.
Investigation showed that tcp_sendmsg() was not using zero-copy to
send the xdr_buf's bvec pages, but instead was relying on memcpy.
This means copying every byte of a large NFS READ payload.
It looks like TLS sockets do indeed support a ->sendpage method,
so it's really not necessary to use xprt_sock_sendmsg() to support
TLS fully on the server. A mechanical reversion of da1661b93b is
not possible at this point, but we can re-implement the server's
TCP socket sendmsg path using kernel_sendpage().
Reported-by: Daire Byrne <daire@dneg.com>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=209439
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 45db630e5f upstream.
Since we allow removing the timeline map at runtime, there is a risk
that rq->hwsp points into a stale page. To control that risk, we hold
the RCU read lock while reading *rq->hwsp, but we missed a couple of
important barriers. First, the unpinning / removal of the timeline map
must be after all RCU readers into that map are complete, i.e. after an
rcu barrier (in this case courtesy of call_rcu()). Secondly, we must
make sure that the rq->hwsp we are about to dereference under the RCU
lock is valid. In this case, we make the rq->hwsp pointer safe during
i915_request_retire() and so we know that rq->hwsp may become invalid
only after the request has been signaled. Therefore is the request is
not yet signaled when we acquire rq->hwsp under the RCU, we know that
rq->hwsp will remain valid for the duration of the RCU read lock.
This is a very small window that may lead to either considering the
request not completed (causing a delay until the request is checked
again, any wait for the request is not affected) or dereferencing an
invalid pointer.
Fixes: 3adac4689f ("drm/i915: Introduce concept of per-timeline (context) HWSP")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: <stable@vger.kernel.org> # v5.1+
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218122421.18344-1-chris@chris-wilson.co.uk
(cherry picked from commit 9bb36cf660)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210118101755.476744-1-chris@chris-wilson.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 348fe1ca5c upstream.
[WHY]
Previously as MPO + ODM Combine was not supported, finding secondary pipes
for each case was mutually exclusive. Now that both are supported at the same
time, both cases should be taken into account when finding a secondary pipe.
[HOW]
If a secondary pipe cannot be found based on previous bottom pipe,
search for a second pipe using next_odm_pipe instead.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Anson Jacob <anson.jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 5.10.x
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c02406428 upstream.
Otherwise a malicious user could (ab)use the "recalculate" feature
that makes dm-integrity calculate the checksums in the background
while the device is already usable. When the system restarts before all
checksums have been calculated, the calculation continues where it was
interrupted even if the recalculate feature is not requested the next
time the dm device is set up.
Disable recalculating if we use internal_hash or journal_hash with a
key (e.g. HMAC) and we don't have the "legacy_recalculate" flag.
This may break activation of a volume, created by an older kernel,
that is not yet fully recalculated -- if this happens, the user should
add the "legacy_recalculate" flag to constructor parameters.
Cc: stable@vger.kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reported-by: Daniel Glockner <dg@emlix.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 809b1e4945 upstream.
This reverts commit
644bda6f34 ("dm table: fall back to getting device using name_to_dev_t()")
dm_get_dev_t() is just used to convert an arbitrary 'path' string
into a dev_t. It doesn't presume that the device is present; that
check will be done later, as the only caller is dm_get_device(),
which does a dm_get_table_device() later on, which will properly
open the device.
So if the path string already _is_ in major:minor representation
we can convert it directly, avoiding a recursion into the filesystem
to lookup the block device.
This avoids a hang in multipath_message() when the filesystem is
inaccessible.
Fixes: 644bda6f34 ("dm table: fall back to getting device using name_to_dev_t()")
Cc: stable@vger.kernel.org
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin Wilck <mwilck@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b191dcba7 upstream.
Commit e7b5d63a82 ("mmc: sdhci-brcmstb: Add shutdown callback")
that added a shutdown callback to the diver, is causing "mmc timeout"
errors on S5 suspend. The problem was that the "remove" was queuing
additional MMC commands after the "shutdown" and these caused
timeouts as the MMC queues were cleaned up for "remove". The
shutdown callback will be changed to calling sdhci-pltfm_suspend
which should get better power savings because the clocks will be
shutdown.
Fixes: e7b5d63a82 ("mmc: sdhci-brcmstb: Add shutdown callback")
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210107221509.6597-1-alcooperx@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a3ed0dc35 upstream.
Automatic Clock Gating is a feature used for the power consumption
optimisation. It turned out that during early init phase it may prevent the
stable voltage switch to 1.8V - due to that on some platforms an endless
printout in dmesg can be observed: "mmc1: 1.8V regulator output did not
became stable" Fix the problem by disabling the ACG at very beginning of
the sdhci_init and let that be enabled later.
Fixes: 3a3748dba8 ("mmc: sdhci-xenon: Add Marvell Xenon SDHC core functionality")
Signed-off-by: Alex Leibovich <alexl@marvell.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Cc: stable@vger.kernel.org
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20201211141656.24915-1-mw@semihalf.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca1219c0a7 upstream.
Commit a44f7cb937 ("mmc: core: use mrq->sbc when sending CMD23 for
RPMB") began to use ACMD23 for RPMB if the host supports ACMD23. In
RPMB ACM23 case, we need to set bit 31 to CMD23 argument, otherwise
RPMB write operation will return general fail.
However, no matter V4 is enabled or not, the dwcmshc's ARGUMENT2
register is 32-bit block count register which doesn't support stuff
bits of CMD23 argument. So let's handle this specific ACMD23 case.
From another side, this patch also prepare for future v4 enabling
for dwcmshc, because from the 4.10 spec, the ARGUMENT2 register is
redefined as 32bit block count which doesn't support stuff bits of
CMD23 argument.
Fixes: a44f7cb937 ("mmc: core: use mrq->sbc when sending CMD23 for RPMB")
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20201229161625.38255233@xhacker.debian
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a85c09a3f upstream.
- JZ4760 and JZ4760B have a similar register layout as the JZ4740, and
don't use the new register layout, which was introduced with the
JZ4770 SoC and not the JZ4760 or JZ4760B SoCs.
- The JZ4740 code path only expected two function modes to be
configurable for each pin, and wouldn't work with more than two. Fix
it for the JZ4760, which has four configurable function modes.
Fixes: 0257595a5c ("pinctrl: Ingenic: Add pinctrl driver for JZ4760 and JZ4760B.")
Cc: <stable@vger.kernel.org> # 5.3
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20201211232810.261565-1-paul@crapouillou.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1e249cb5b7 upstream.
When lazytime is enabled and an inode is being written due to its
in-memory updated timestamps having expired, either due to a sync() or
syncfs() system call or due to dirtytime_expire_interval having elapsed,
the VFS needs to inform the filesystem so that the filesystem can copy
the inode's timestamps out to the on-disk data structures.
This is done by __writeback_single_inode() calling
mark_inode_dirty_sync(), which then calls ->dirty_inode(I_DIRTY_SYNC).
However, this occurs after __writeback_single_inode() has already
cleared the dirty flags from ->i_state. This causes two bugs:
- mark_inode_dirty_sync() redirties the inode, causing it to remain
dirty. This wastefully causes the inode to be written twice. But
more importantly, it breaks cases where sync_filesystem() is expected
to clean dirty inodes. This includes the FS_IOC_REMOVE_ENCRYPTION_KEY
ioctl (as reported at
https://lore.kernel.org/r/20200306004555.GB225345@gmail.com), as well
as possibly filesystem freezing (freeze_super()).
- Since ->i_state doesn't contain I_DIRTY_TIME when ->dirty_inode() is
called from __writeback_single_inode() for lazytime expiration,
xfs_fs_dirty_inode() ignores the notification. (XFS only cares about
lazytime expirations, and it assumes that i_state will contain
I_DIRTY_TIME during those.) Therefore, lazy timestamps aren't
persisted by sync(), syncfs(), or dirtytime_expire_interval on XFS.
Fix this by moving the call to mark_inode_dirty_sync() to earlier in
__writeback_single_inode(), before the dirty flags are cleared from
i_state. This makes filesystems be properly notified of the timestamp
expiration, and it avoids incorrectly redirtying the inode.
This fixes xfstest generic/580 (which tests
FS_IOC_REMOVE_ENCRYPTION_KEY) when run on ext4 or f2fs with lazytime
enabled. It also fixes the new lazytime xfstest I've proposed, which
reproduces the above-mentioned XFS bug
(https://lore.kernel.org/r/20210105005818.92978-1-ebiggers@kernel.org).
Alternatively, we could call ->dirty_inode(I_DIRTY_SYNC) directly. But
due to the introduction of I_SYNC_QUEUED, mark_inode_dirty_sync() is the
right thing to do because mark_inode_dirty_sync() now knows not to move
the inode to a writeback list if it is currently queued for sync.
Fixes: 0ae45f63d4 ("vfs: add support for a lazytime mount option")
Cc: stable@vger.kernel.org
Depends-on: 5afced3bf2 ("writeback: Avoid skipping inode writeback")
Link: https://lore.kernel.org/r/20210112190253.64307-2-ebiggers@kernel.org
Suggested-by: Jan Kara <jack@suse.cz>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 518837e650 upstream.
When an incremental send finds an extent that is shared, it checks which
file extent items in the range refer to that extent, and for those it
emits clone operations, while for others it emits regular write operations
to avoid corruption at the destination (as described and fixed by commit
d906d49fc5 ("Btrfs: send, fix file corruption due to incorrect cloning
operations")).
However when the root we are cloning from is the send root, we are cloning
from the inode currently being processed and the source file range has
several extent items that partially point to the desired extent, with an
offset smaller than the offset in the file extent item for the range we
want to clone into, it can cause the algorithm to issue a clone operation
that starts at the current eof of the file being processed in the receiver
side, in which case the receiver will fail, with EINVAL, when attempting
to execute the clone operation.
Example reproducer:
$ cat test-send-clone.sh
#!/bin/bash
DEV=/dev/sdi
MNT=/mnt/sdi
mkfs.btrfs -f $DEV >/dev/null
mount $DEV $MNT
# Create our test file with a single and large extent (1M) and with
# different content for different file ranges that will be reflinked
# later.
xfs_io -f \
-c "pwrite -S 0xab 0 128K" \
-c "pwrite -S 0xcd 128K 128K" \
-c "pwrite -S 0xef 256K 256K" \
-c "pwrite -S 0x1a 512K 512K" \
$MNT/foobar
btrfs subvolume snapshot -r $MNT $MNT/snap1
btrfs send -f /tmp/snap1.send $MNT/snap1
# Now do a series of changes to our file such that we end up with
# different parts of the extent reflinked into different file offsets
# and we overwrite a large part of the extent too, so no file extent
# items refer to that part that was overwritten. This used to confuse
# the algorithm used by the kernel to figure out which file ranges to
# clone, making it attempt to clone from a source range starting at
# the current eof of the file, resulting in the receiver to fail since
# it is an invalid clone operation.
#
xfs_io -c "reflink $MNT/foobar 64K 1M 960K" \
-c "reflink $MNT/foobar 0K 512K 256K" \
-c "reflink $MNT/foobar 512K 128K 256K" \
-c "pwrite -S 0x73 384K 640K" \
$MNT/foobar
btrfs subvolume snapshot -r $MNT $MNT/snap2
btrfs send -f /tmp/snap2.send -p $MNT/snap1 $MNT/snap2
echo -e "\nFile digest in the original filesystem:"
md5sum $MNT/snap2/foobar
# Now unmount the filesystem, create a new one, mount it and try to
# apply both send streams to recreate both snapshots.
umount $DEV
mkfs.btrfs -f $DEV >/dev/null
mount $DEV $MNT
btrfs receive -f /tmp/snap1.send $MNT
btrfs receive -f /tmp/snap2.send $MNT
# Must match what we got in the original filesystem of course.
echo -e "\nFile digest in the new filesystem:"
md5sum $MNT/snap2/foobar
umount $MNT
When running the reproducer, the incremental send operation fails due to
an invalid clone operation:
$ ./test-send-clone.sh
wrote 131072/131072 bytes at offset 0
128 KiB, 32 ops; 0.0015 sec (80.906 MiB/sec and 20711.9741 ops/sec)
wrote 131072/131072 bytes at offset 131072
128 KiB, 32 ops; 0.0013 sec (90.514 MiB/sec and 23171.6148 ops/sec)
wrote 262144/262144 bytes at offset 262144
256 KiB, 64 ops; 0.0025 sec (98.270 MiB/sec and 25157.2327 ops/sec)
wrote 524288/524288 bytes at offset 524288
512 KiB, 128 ops; 0.0052 sec (95.730 MiB/sec and 24506.9883 ops/sec)
Create a readonly snapshot of '/mnt/sdi' in '/mnt/sdi/snap1'
At subvol /mnt/sdi/snap1
linked 983040/983040 bytes at offset 1048576
960 KiB, 1 ops; 0.0006 sec (1.419 GiB/sec and 1550.3876 ops/sec)
linked 262144/262144 bytes at offset 524288
256 KiB, 1 ops; 0.0020 sec (120.192 MiB/sec and 480.7692 ops/sec)
linked 262144/262144 bytes at offset 131072
256 KiB, 1 ops; 0.0018 sec (133.833 MiB/sec and 535.3319 ops/sec)
wrote 655360/655360 bytes at offset 393216
640 KiB, 160 ops; 0.0093 sec (66.781 MiB/sec and 17095.8436 ops/sec)
Create a readonly snapshot of '/mnt/sdi' in '/mnt/sdi/snap2'
At subvol /mnt/sdi/snap2
File digest in the original filesystem:
9c13c61cb0b9f5abf45344375cb04dfa /mnt/sdi/snap2/foobar
At subvol snap1
At snapshot snap2
ERROR: failed to clone extents to foobar: Invalid argument
File digest in the new filesystem:
132f0396da8f48d2e667196bff882cfc /mnt/sdi/snap2/foobar
The clone operation is invalid because its source range starts at the
current eof of the file in the receiver, causing the receiver to get
an EINVAL error from the clone operation when attempting it.
For the example above, what happens is the following:
1) When processing the extent at file offset 1M, the algorithm checks that
the extent is shared and can be (fully or partially) found at file
offset 0.
At this point the file has a size (and eof) of 1M at the receiver;
2) It finds that our extent item at file offset 1M has a data offset of
64K and, since the file extent item at file offset 0 has a data offset
of 0, it issues a clone operation, from the same file and root, that
has a source range offset of 64K, destination offset of 1M and a length
of 64K, since the extent item at file offset 0 refers only to the first
128K of the shared extent.
After this clone operation, the file size (and eof) at the receiver is
increased from 1M to 1088K (1M + 64K);
3) Now there's still 896K (960K - 64K) of data left to clone or write, so
it checks for the next file extent item, which starts at file offset
128K. This file extent item has a data offset of 0 and a length of
256K, so a clone operation with a source range offset of 256K, a
destination offset of 1088K (1M + 64K) and length of 128K is issued.
After this operation the file size (and eof) at the receiver increases
from 1088K to 1216K (1088K + 128K);
4) Now there's still 768K (896K - 128K) of data left to clone or write, so
it checks for the next file extent item, located at file offset 384K.
This file extent item points to a different extent, not the one we want
to clone, with a length of 640K. So we issue a write operation into the
file range 1216K (1088K + 128K, end of the last clone operation), with
a length of 640K and with a data matching the one we can find for that
range in send root.
After this operation, the file size (and eof) at the receiver increases
from 1216K to 1856K (1216K + 640K);
5) Now there's still 128K (768K - 640K) of data left to clone or write, so
we look into the file extent item, which is for file offset 1M and it
points to the extent we want to clone, with a data offset of 64K and a
length of 960K.
However this matches the file offset we started with, the start of the
range to clone into. So we can't for sure find any file extent item
from here onwards with the rest of the data we want to clone, yet we
proceed and since the file extent item points to the shared extent,
with a data offset of 64K, we issue a clone operation with a source
range starting at file offset 1856K, which matches the file extent
item's offset, 1M, plus the amount of data cloned and written so far,
which is 64K (step 2) + 128K (step 3) + 640K (step 4). This clone
operation is invalid since the source range offset matches the current
eof of the file in the receiver. We should have stopped looking for
extents to clone at this point and instead fallback to write, which
would simply the contain the data in the file range from 1856K to
1856K + 128K.
So fix this by stopping the loop that looks for file ranges to clone at
clone_range() when we reach the current eof of the file being processed,
if we are cloning from the same file and using the send root as the clone
root. This ensures any data not yet cloned will be sent to the receiver
through a write operation.
A test case for fstests will follow soon.
Reported-by: Massimo B. <massimo.b@gmx.net>
Link: https://lore.kernel.org/linux-btrfs/6ae34776e85912960a253a8327068a892998e685.camel@gmx.net/
Fixes: 11f2069c11 ("Btrfs: send, allow clone operations within the same file")
CC: stable@vger.kernel.org # 5.5+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 34d1eb0e59 upstream.
If we fail to update a block group item in the loop we'll break, however
we'll do btrfs_run_delayed_refs and lose our error value in ret, and
thus not clean up properly. Fix this by only running the delayed refs
if there was no failure.
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 49ecc679ab upstream.
Zygo reported the following KASAN splat:
BUG: KASAN: use-after-free in btrfs_backref_cleanup_node+0x18a/0x420
Read of size 8 at addr ffff888112402950 by task btrfs/28836
CPU: 0 PID: 28836 Comm: btrfs Tainted: G W 5.10.0-e35f27394290-for-next+ #23
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-1 04/01/2014
Call Trace:
dump_stack+0xbc/0xf9
? btrfs_backref_cleanup_node+0x18a/0x420
print_address_description.constprop.8+0x21/0x210
? record_print_text.cold.34+0x11/0x11
? btrfs_backref_cleanup_node+0x18a/0x420
? btrfs_backref_cleanup_node+0x18a/0x420
kasan_report.cold.10+0x20/0x37
? btrfs_backref_cleanup_node+0x18a/0x420
__asan_load8+0x69/0x90
btrfs_backref_cleanup_node+0x18a/0x420
btrfs_backref_release_cache+0x83/0x1b0
relocate_block_group+0x394/0x780
? merge_reloc_roots+0x4a0/0x4a0
btrfs_relocate_block_group+0x26e/0x4c0
btrfs_relocate_chunk+0x52/0x120
btrfs_balance+0xe2e/0x1900
? check_flags.part.50+0x6c/0x1e0
? btrfs_relocate_chunk+0x120/0x120
? kmem_cache_alloc_trace+0xa06/0xcb0
? _copy_from_user+0x83/0xc0
btrfs_ioctl_balance+0x3a7/0x460
btrfs_ioctl+0x24c8/0x4360
? __kasan_check_read+0x11/0x20
? check_chain_key+0x1f4/0x2f0
? __asan_loadN+0xf/0x20
? btrfs_ioctl_get_supported_features+0x30/0x30
? kvm_sched_clock_read+0x18/0x30
? check_chain_key+0x1f4/0x2f0
? lock_downgrade+0x3f0/0x3f0
? handle_mm_fault+0xad6/0x2150
? do_vfs_ioctl+0xfc/0x9d0
? ioctl_file_clone+0xe0/0xe0
? check_flags.part.50+0x6c/0x1e0
? check_flags.part.50+0x6c/0x1e0
? check_flags+0x26/0x30
? lock_is_held_type+0xc3/0xf0
? syscall_enter_from_user_mode+0x1b/0x60
? do_syscall_64+0x13/0x80
? rcu_read_lock_sched_held+0xa1/0xd0
? __kasan_check_read+0x11/0x20
? __fget_light+0xae/0x110
__x64_sys_ioctl+0xc3/0x100
do_syscall_64+0x37/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x7f4c4bdfe427
Allocated by task 28836:
kasan_save_stack+0x21/0x50
__kasan_kmalloc.constprop.18+0xbe/0xd0
kasan_kmalloc+0x9/0x10
kmem_cache_alloc_trace+0x410/0xcb0
btrfs_backref_alloc_node+0x46/0xf0
btrfs_backref_add_tree_node+0x60d/0x11d0
build_backref_tree+0xc5/0x700
relocate_tree_blocks+0x2be/0xb90
relocate_block_group+0x2eb/0x780
btrfs_relocate_block_group+0x26e/0x4c0
btrfs_relocate_chunk+0x52/0x120
btrfs_balance+0xe2e/0x1900
btrfs_ioctl_balance+0x3a7/0x460
btrfs_ioctl+0x24c8/0x4360
__x64_sys_ioctl+0xc3/0x100
do_syscall_64+0x37/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Freed by task 28836:
kasan_save_stack+0x21/0x50
kasan_set_track+0x20/0x30
kasan_set_free_info+0x1f/0x30
__kasan_slab_free+0xf3/0x140
kasan_slab_free+0xe/0x10
kfree+0xde/0x200
btrfs_backref_error_cleanup+0x452/0x530
build_backref_tree+0x1a5/0x700
relocate_tree_blocks+0x2be/0xb90
relocate_block_group+0x2eb/0x780
btrfs_relocate_block_group+0x26e/0x4c0
btrfs_relocate_chunk+0x52/0x120
btrfs_balance+0xe2e/0x1900
btrfs_ioctl_balance+0x3a7/0x460
btrfs_ioctl+0x24c8/0x4360
__x64_sys_ioctl+0xc3/0x100
do_syscall_64+0x37/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xa9
This occurred because we freed our backref node in
btrfs_backref_error_cleanup(), but then tried to free it again in
btrfs_backref_release_cache(). This is because
btrfs_backref_release_cache() will cycle through all of the
cache->leaves nodes and free them up. However
btrfs_backref_error_cleanup() freed the backref node with
btrfs_backref_free_node(), which simply kfree()d the backref node
without unlinking it from the cache. Change this to a
btrfs_backref_drop_node(), which does the appropriate cleanup and
removes the node from the cache->leaves list, so when we go to free the
remaining cache we don't trip over items we've already dropped.
Fixes: 75bfb9aff4 ("Btrfs: cleanup error handling in build_backref_tree")
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 18d3bff411 upstream.
This was partially fixed by f3e3d9cc35 ("btrfs: avoid possible signal
interruption of btrfs_drop_snapshot() on relocation tree"), however it
missed a spot when we restart a trans handle because we need to end the
transaction. The fix is the same, simply use btrfs_join_transaction()
instead of btrfs_start_transaction() when deleting reloc roots.
Fixes: f3e3d9cc35 ("btrfs: avoid possible signal interruption of btrfs_drop_snapshot() on relocation tree")
CC: stable@vger.kernel.org # 5.4+
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 78a18fec52 upstream.
Set the acpi_device pointer which acpi_bus_get_device() returns-by-
reference to NULL on errors.
We've recently had 2 cases where callers of acpi_bus_get_device()
did not properly error check the return value, so set the returned-
by-reference acpi_device pointer to NULL, because at least some
callers of acpi_bus_get_device() expect that to be done on errors.
[ rjw: This issue was exposed by commit 71da201f38 ("ACPI: scan:
Defer enumeration of devices with _DEP lists") which caused it to
be much more likely to occur on some systems, but the real defect
had been introduced by an earlier commit. ]
Fixes: 40e7fcb192 ("ACPI: Add _DEP support to fix battery issue on Asus T100TA")
Fixes: bcfcd409d4 ("usb: split code locating ACPI companion into port and device")
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Diagnosed-by: Rafael J. Wysocki <rafael@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: All applicable <stable@vger.kernel.org>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 004b8ae9e2 upstream.
In commit d68b29584c ("dm crypt: use GFP_ATOMIC when allocating
crypto requests from softirq") code was incorrectly copy and pasted
from crypt_alloc_req_skcipher()'s crypto request allocation code to
crypt_alloc_req_aead(). It is OK from runtime perspective as both
simple encryption request pointer and AEAD request pointer are part of
a union, but may confuse code reviewers.
Fixes: d68b29584c ("dm crypt: use GFP_ATOMIC when allocating crypto requests from softirq")
Cc: stable@vger.kernel.org # v5.9+
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Ignat Korchagin <ignat@cloudflare.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f419e5940f upstream.
Newer ideapads (e.g.: Yoga 14s, 720S 14) come with ELAN0634 touchpad do not
use EC to switch touchpad.
Reading VPCCMD_R_TOUCHPAD will return zero thus touchpad may be blocked
unexpectedly.
Writing VPCCMD_W_TOUCHPAD may cause a spurious key press.
Add has_touchpad_switch to workaround these machines.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: stable@vger.kernel.org # 5.4+
--
v2: Specify touchpad to ELAN0634
v3: Stupid missing ! in v2
v4: Correct acpi_dev_present usage (Hans)
Link: https://lore.kernel.org/r/20210107144438.12605-1-jiaxun.yang@flygoat.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9bba962755 upstream.
There are several reports about the tps6598x causing
interrupt flood on boards with the INT3515 ACPI node, which
then causes instability. There appears to be several
problems with the interrupt. One problem is that the
I2CSerialBus resources do not always map to the Interrupt
resource with the same index, but that is not the only
problem. We have not been able to come up with a solution
for all the issues, and because of that disabling the device
for now.
The PD controller on these platforms is autonomous, and the
purpose for the driver is primarily to supply status to the
userspace, so this will not affect any functionality.
Reported-by: Moody Salem <moody@uniswap.org>
Fixes: a3dd034a17 ("ACPI / scan: Create platform device for INT3515 ACPI nodes")
Cc: stable@vger.kernel.org
BugLink: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1883511
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201223143644.33341-1-heikki.krogerus@linux.intel.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bc1c2048ab upstream.
In order to not to start returning errors when new I2C_M flags are
added, change behavior to just ignore all flags that we don't know
about. This includes the I2C_M_DMA_SAFE flag that already exists but
causes -EINVAL to be returned for valid transactions.
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 27b7c6e096 upstream.
Upon a communication error, the interrupt handler can call
tegra_i2c_disable_packet_mode. This causes a sleeping poll to happen
unless the current transaction was marked atomic. Fix this by
making the poll happen atomically if we are in an IRQ.
This matches the behavior prior to the patch mentioned
in the Fixes tag.
Fixes: ede2299f71 ("i2c: tegra: Support atomic transfers")
Cc: stable@vger.kernel.org
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ad2a970d2 upstream.
TID stuck is seen when there is a race in
CPL_PASS_ACCEPT_RPL/CPL_ABORT_REQ and abort is arriving
before the accept reply, which sets the queue number.
In this case HW ends up sending CPL_ABORT_RPL_RSS to an
incorrect ingress queue.
V1->V2:
- Removed the unused variable len in chtls_set_quiesce_ctrl().
V2->V3:
- As kfree_skb() has a check for null skb, so removed this
check before calling kfree_skb() in func chtls_send_reset().
Fixes: cc35c88ae4 ("crypto : chtls - CPL handler definition")
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: Ayush Sawal <ayush.sawal@chelsio.com>
Link: https://lore.kernel.org/r/20210112053600.24590-1-ayush.sawal@chelsio.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07b90056cb upstream.
Currently the following happens when a DSA master driver unbinds while
there are DSA switches attached to it:
$ echo 0000:00:00.5 > /sys/bus/pci/drivers/mscc_felix/unbind
------------[ cut here ]------------
WARNING: CPU: 0 PID: 392 at net/core/dev.c:9507
Call trace:
rollback_registered_many+0x5fc/0x688
unregister_netdevice_queue+0x98/0x120
dsa_slave_destroy+0x4c/0x88
dsa_port_teardown.part.16+0x78/0xb0
dsa_tree_teardown_switches+0x58/0xc0
dsa_unregister_switch+0x104/0x1b8
felix_pci_remove+0x24/0x48
pci_device_remove+0x48/0xf0
device_release_driver_internal+0x118/0x1e8
device_driver_detach+0x28/0x38
unbind_store+0xd0/0x100
Located at the above location is this WARN_ON:
/* Notifier chain MUST detach us all upper devices. */
WARN_ON(netdev_has_any_upper_dev(dev));
Other stacked interfaces, like VLAN, do indeed listen for
NETDEV_UNREGISTER on the real_dev and also unregister themselves at that
time, which is clearly the behavior that rollback_registered_many
expects. But DSA interfaces are not VLAN. They have backing hardware
(platform devices, PCI devices, MDIO, SPI etc) which have a life cycle
of their own and we can't just trigger an unregister from the DSA
framework when we receive a netdev notifier that the master unregisters.
Luckily, there is something we can do, and that is to inform the driver
core that we have a runtime dependency to the DSA master interface's
device, and create a device link where that is the supplier and we are
the consumer. Having this device link will make the DSA switch unbind
before the DSA master unbinds, which is enough to avoid the WARN_ON from
rollback_registered_many.
Note that even before the blamed commit, DSA did nothing intelligent
when the master interface got unregistered either. See the discussion
here:
https://lore.kernel.org/netdev/20200505210253.20311-1-f.fainelli@gmail.com/
But this time, at least the WARN_ON is loud enough that the
upper_dev_link commit can be blamed.
The advantage with this approach vs dev_hold(master) in the attached
link is that the latter is not meant for long term reference counting.
With dev_hold, the only thing that will happen is that when the user
attempts an unbind of the DSA master, netdev_wait_allrefs will keep
waiting and waiting, due to DSA keeping the refcount forever. DSA would
not access freed memory corresponding to the master interface, but the
unbind would still result in a freeze. Whereas with device links,
graceful teardown is ensured. It even works with cascaded DSA trees.
$ echo 0000:00:00.2 > /sys/bus/pci/drivers/fsl_enetc/unbind
[ 1818.797546] device swp0 left promiscuous mode
[ 1819.301112] sja1105 spi2.0: Link is Down
[ 1819.307981] DSA: tree 1 torn down
[ 1819.312408] device eno2 left promiscuous mode
[ 1819.656803] mscc_felix 0000:00:00.5: Link is Down
[ 1819.667194] DSA: tree 0 torn down
[ 1819.711557] fsl_enetc 0000:00:00.2 eno2: Link is Down
This approach allows us to keep the DSA framework absolutely unchanged,
and the driver core will just know to unbind us first when the master
goes away - as opposed to the large (and probably impossible) rework
required if attempting to listen for NETDEV_UNREGISTER.
As per the documentation at Documentation/driver-api/device_link.rst,
specifying the DL_FLAG_AUTOREMOVE_CONSUMER flag causes the device link
to be automatically purged when the consumer fails to probe or later
unbinds. So we don't need to keep the consumer_link variable in struct
dsa_switch.
Fixes: 2f1e8ea726 ("net: dsa: link interfaces with the DSA master to get rid of lockdep warnings")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210111230943.3701806-1-olteanv@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1f02efd1bb ]
Use of __napi_schedule_irqoff() is not safe with PREEMPT_RT in which
hard interrupts are not disabled while running the threaded interrupt.
Using __napi_schedule() works for both PREEMPT_RT and mainline Linux,
just at the cost of an additional check if interrupts are disabled for
mainline (since they are already disabled).
Similar to the fix done for enetc commit 215602a8d2 ("enetc: use
napi_schedule to be compatible with PREEMPT_RT")
Signed-off-by: Seb Laveze <sebastien.laveze@nxp.com>
Link: https://lore.kernel.org/r/20210112140121.1487619-1-sebastien.laveze@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d52e419ac8 ]
Clang static analysis reports the following:
net/rxrpc/key.c:657:11: warning: Assigned value is garbage or undefined
toksize = toksizes[tok++];
^ ~~~~~~~~~~~~~~~
rxrpc_read() contains two consecutive loops. The first loop calculates the
token sizes and stores the results in toksizes[] and the second one uses
the array. When there is an error in identifying the token in the first
loop, the token is skipped, no change is made to the toksizes[] array.
When the same error happens in the second loop, the token is not skipped.
This will cause the toksizes[] array to be out of step and will overrun
past the calculated sizes.
Fix this by making both loops log a message and return an error in this
case. This should only happen if a new token type is incompletely
implemented, so it should normally be impossible to trigger this.
Fixes: 9a059cd5ca ("rxrpc: Downgrade the BUG() for unsupported token type in rxrpc_read()")
Reported-by: Tom Rix <trix@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/161046503122.2445787.16714129930607546635.stgit@warthog.procyon.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 91158e1680 ]
Florian reported a use-after-free bug in devlink_nl_port_fill found with
KASAN:
(devlink_nl_port_fill)
(devlink_port_notify)
(devlink_port_unregister)
(dsa_switch_teardown.part.3)
(dsa_tree_teardown_switches)
(dsa_unregister_switch)
(bcm_sf2_sw_remove)
(platform_remove)
(device_release_driver_internal)
(device_links_unbind_consumers)
(device_release_driver_internal)
(device_driver_detach)
(unbind_store)
Allocated by task 31:
alloc_netdev_mqs+0x5c/0x50c
dsa_slave_create+0x110/0x9c8
dsa_register_switch+0xdb0/0x13a4
b53_switch_register+0x47c/0x6dc
bcm_sf2_sw_probe+0xaa4/0xc98
platform_probe+0x90/0xf4
really_probe+0x184/0x728
driver_probe_device+0xa4/0x278
__device_attach_driver+0xe8/0x148
bus_for_each_drv+0x108/0x158
Freed by task 249:
free_netdev+0x170/0x194
dsa_slave_destroy+0xac/0xb0
dsa_port_teardown.part.2+0xa0/0xb4
dsa_tree_teardown_switches+0x50/0xc4
dsa_unregister_switch+0x124/0x250
bcm_sf2_sw_remove+0x98/0x13c
platform_remove+0x44/0x5c
device_release_driver_internal+0x150/0x254
device_links_unbind_consumers+0xf8/0x12c
device_release_driver_internal+0x84/0x254
device_driver_detach+0x30/0x34
unbind_store+0x90/0x134
What happens is that devlink_port_unregister emits a netlink
DEVLINK_CMD_PORT_DEL message which associates the devlink port that is
getting unregistered with the ifindex of its corresponding net_device.
Only trouble is, the net_device has already been unregistered.
It looks like we can stub out the search for a corresponding net_device
if we clear the devlink_port's type. This looks like a bit of a hack,
but also seems to be the reason why the devlink_port_type_clear function
exists in the first place.
Fixes: 3122433eb5 ("net: dsa: Register devlink ports before calling DSA driver setup()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian fainelli <f.fainelli@gmail.com>
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210112004831.3778323-1-olteanv@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3226b158e6 ]
Both virtio net and napi_get_frags() allocate skbs
with a very small skb->head
While using page fragments instead of a kmalloc backed skb->head might give
a small performance improvement in some cases, there is a huge risk of
under estimating memory usage.
For both GOOD_COPY_LEN and GRO_MAX_HEAD, we can fit at least 32 allocations
per page (order-3 page in x86), or even 64 on PowerPC
We have been tracking OOM issues on GKE hosts hitting tcp_mem limits
but consuming far more memory for TCP buffers than instructed in tcp_mem[2]
Even if we force napi_alloc_skb() to only use order-0 pages, the issue
would still be there on arches with PAGE_SIZE >= 32768
This patch makes sure that small skb head are kmalloc backed, so that
other objects in the slab page can be reused instead of being held as long
as skbs are sitting in socket queues.
Note that we might in the future use the sk_buff napi cache,
instead of going through a more expensive __alloc_skb()
Another idea would be to use separate page sizes depending
on the allocated length (to never have more than 4 frags per page)
I would like to thank Greg Thelen for his precious help on this matter,
analysing crash dumps is always a time consuming task.
Fixes: fd11a83dd3 ("net: Pull out core bits of __netdev_alloc_skb and add __napi_alloc_skb")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Greg Thelen <gthelen@google.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://lore.kernel.org/r/20210113161819.1155526-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fe28c53ed7 ]
The Synopsys TSN MAC supports Qbv base times in the past, but only up to a
certain limit. As a result, a taprio qdisc configuration with a small
base time (for example when treating the base time as a simple phase
offset) is not applied by the hardware and silently ignored.
This was observed on an NXP i.MX8MPlus device, but likely affects all
TSN-variants of the MAC.
Fix the issue by making sure the base time is in the future, pushing it by
an integer amount of cycle times if needed. (a similar check is already
done in several other taprio implementations, see for example
drivers/net/ethernet/intel/igc/igc_tsn.c#L116 or
drivers/net/dsa/sja1105/sja1105_ptp.h#L39).
Fixes: b60189e039 ("net: stmmac: Integrate EST with TAPRIO scheduler API")
Signed-off-by: Yannick Vignon <yannick.vignon@nxp.com>
Link: https://lore.kernel.org/r/20210113131557.24651-2-yannick.vignon@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b76889ff51 ]
When configuring a 802.1Qbv schedule through the tc taprio qdisc on an NXP
i.MX8MPlus device, the effective cycle time differed from the requested one
by N*96ns, with N number of entries in the Qbv Gate Control List. This is
because the driver was adding a 96ns margin to each interval of the GCL,
apparently to account for the IPG. The problem was observed on NXP
i.MX8MPlus devices but likely affected all devices relying on the same
configuration callback (dwmac 4.00, 4.10, 5.10 variants).
Fix the issue by removing the margins, and simply setup the MAC with the
provided cycle time value. This is the behavior expected by the user-space
API, as altering the Qbv schedule timings would break standards conformance.
This is also the behavior of several other Ethernet MAC implementations
supporting taprio, including the dwxgmac variant of stmmac.
Fixes: 504723af0d ("net: stmmac: Add basic EST support for GMAC5+")
Signed-off-by: Yannick Vignon <yannick.vignon@nxp.com>
Link: https://lore.kernel.org/r/20210113131557.24651-1-yannick.vignon@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7128c834d3 ]
Currently, the function i40e_construct_skb_zc only frees the input xdp
buffer when the output skb is successfully built. On error, the
function i40e_clean_rx_irq_zc does not commit anything for the current
packet descriptor and simply exits the packet descriptor processing
loop, with the plan to restart the processing of this descriptor on
the next invocation. Therefore, on error the ring next-to-clean
pointer should not advance, the xdp i.e. *bi buffer should not be
freed and the current buffer info should not be invalidated by setting
*bi to NULL. Therefore, the *bi should only be set to NULL when the
function i40e_construct_skb_zc is successful, otherwise a NULL *bi
will be dereferenced when the work for the current descriptor is
eventually restarted.
Fixes: 3b4f0b66c2 ("i40e, xsk: Migrate to new MEM_TYPE_XSK_BUFF_POOL")
Signed-off-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/r/20210111181138.49757-1-cristian.dumitrescu@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a95d25dd7b ]
The call state may be changed at any time by the data-ready routine in
response to received packets, so if the call state is to be read and acted
upon several times in a function, READ_ONCE() must be used unless the call
state lock is held.
As it happens, we used READ_ONCE() to read the state a few lines above the
unmarked read in rxrpc_input_data(), so use that value rather than
re-reading it.
Fixes: a158bdd324 ("rxrpc: Fix call timeouts")
Signed-off-by: Baptiste Lepers <baptiste.lepers@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Link: https://lore.kernel.org/r/161046715522.2450566.488819910256264150.stgit@warthog.procyon.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit df85bc140a ]
In commit 826f328e2b ("net: dcb: Validate netlink message in DCB
handler"), Linux started rejecting RTM_GETDCB netlink messages if they
contained a set-like DCB_CMD_ command.
The reason was that privileges were only verified for RTM_SETDCB messages,
but the value that determined the action to be taken is the command, not
the message type. And validation of message type against the DCB command
was the obvious missing piece.
Unfortunately it turns out that mlnx_qos, a somewhat widely deployed tool
for configuration of DCB, accesses the DCB set-like APIs through
RTM_GETDCB.
Therefore do not bounce the discrepancy between message type and command.
Instead, in addition to validating privileges based on the actual message
type, validate them also based on the expected message type. This closes
the loophole of allowing DCB configuration on non-admin accounts, while
maintaining backward compatibility.
Fixes: 2f90b8657e ("ixgbe: this patch adds support for DCB to the kernel and ixgbe driver")
Fixes: 826f328e2b ("net: dcb: Validate netlink message in DCB handler")
Signed-off-by: Petr Machata <petrm@nvidia.com>
Link: https://lore.kernel.org/r/a3edcfda0825f2aa2591801c5232f2bbf2d8a554.1610384801.git.me@pmachata.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 826f328e2b ]
DCB uses the same handler function for both RTM_GETDCB and RTM_SETDCB
messages. dcb_doit() bounces RTM_SETDCB mesasges if the user does not have
the CAP_NET_ADMIN capability.
However, the operation to be performed is not decided from the DCB message
type, but from the DCB command. Thus DCB_CMD_*_GET commands are used for
reading DCB objects, the corresponding SET and DEL commands are used for
manipulation.
The assumption is that set-like commands will be sent via an RTM_SETDCB
message, and get-like ones via RTM_GETDCB. However, this assumption is not
enforced.
It is therefore possible to manipulate DCB objects without CAP_NET_ADMIN
capability by sending the corresponding command in an RTM_GETDCB message.
That is a bug. Fix it by validating the type of the request message against
the type used for the response.
Fixes: 2f90b8657e ("ixgbe: this patch adds support for DCB to the kernel and ixgbe driver")
Signed-off-by: Petr Machata <me@pmachata.org>
Link: https://lore.kernel.org/r/a2a9b88418f3a58ef211b718f2970128ef9e3793.1608673640.git.me@pmachata.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9bd6b629c3 ]
esp(6)_output_head uses skb_page_frag_refill to allocate a buffer for
the esp trailer.
It accesses the page with kmap_atomic to handle highmem. But
skb_page_frag_refill can return compound pages, of which
kmap_atomic only maps the first underlying page.
skb_page_frag_refill does not return highmem, because flag
__GFP_HIGHMEM is not set. ESP uses it in the same manner as TCP.
That also does not call kmap_atomic, but directly uses page_address,
in skb_copy_to_page_nocache. Do the same for ESP.
This issue has become easier to trigger with recent kmap local
debugging feature CONFIG_DEBUG_KMAP_LOCAL_FORCE_MAP.
Fixes: cac2661c53 ("esp4: Avoid skb_cow_data whenever possible")
Fixes: 03e2a30f6a ("esp6: Avoid skb_cow_data whenever possible")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e56b3d94d9 ]
MSFT ActiveSync implementation requires that the size of the response for
incoming query is to be provided in the request input length. Failure to
set the input size proper results in failed request transfer, where the
ActiveSync counterpart reports the NDIS_STATUS_INVALID_LENGTH (0xC0010014L)
error.
Set the input size for OID_GEN_PHYSICAL_MEDIUM query to the expected size
of the response in order for the ActiveSync to properly respond to the
request.
Fixes: 039ee17d1b ("rndis_host: Add RNDIS physical medium checking into generic_rndis_bind()")
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Link: https://lore.kernel.org/r/20210108095839.3335-1-andrey.zhizhikin@leica-geosystems.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b06ca3d5a4 ]
Increase critical threshold for ASIC thermal zone from 110C to 140C
according to the system hardware requirements. All the supported ASICs
(Spectrum-1, Spectrum-2, Spectrum-3) could be still operational with ASIC
temperature below 140C. With the old critical threshold value system
can perform unjustified shutdown.
All the systems equipped with the above ASICs implement thermal
protection mechanism at firmware level and firmware could decide to
perform system thermal shutdown in case the temperature is below 140C.
So with the new threshold system will not meltdown, while thermal
operating range will be aligned with hardware abilities.
Fixes: 41e760841d ("mlxsw: core: Replace thermal temperature trips with defines")
Fixes: a50c1e3565 ("mlxsw: core: Implement thermal zone")
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 57726ebe27 ]
Validate thresholds to avoid a single failure due to some transceiver
unreliability. Ignore the last readouts in case warning temperature is
above alarm temperature, since it can cause unexpected thermal
shutdown. Stay with the previous values and refresh threshold within
the next iteration.
This is a rare scenario, but it was observed at a customer site.
Fixes: 6a79507cfe ("mlxsw: core: Extend thermal module with per QSFP module thermal zones")
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b210de4f8c ]
There are cases where GSO segment's length exceeds the egress MTU:
- Forwarding of a TCP GRO skb, when DF flag is not set.
- Forwarding of an skb that arrived on a virtualisation interface
(virtio-net/vhost/tap) with TSO/GSO size set by other network
stack.
- Local GSO skb transmitted on an NETIF_F_TSO tunnel stacked over an
interface with a smaller MTU.
- Arriving GRO skb (or GSO skb in a virtualised environment) that is
bridged to a NETIF_F_TSO tunnel stacked over an interface with an
insufficient MTU.
If so:
- Consume the SKB and its segments.
- Issue an ICMP packet with 'Packet Too Big' message containing the
MTU, allowing the source host to reduce its Path MTU appropriately.
Note: These cases are handled in the same manner in IPv4 output finish.
This patch aligns the behavior of IPv6 and the one of IPv4.
Fixes: 9e50849054 ("netfilter: ipv6: move POSTROUTING invocation before fragmentation")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/1610027418-30438-1-git-send-email-ayal@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a2bc221b97 ]
For all PCI functions on the netxen_nic adapter, interrupt
mode (INTx or MSI) configuration is dependent on what has
been configured by the PCI function zero in the shared
interrupt register, as these adapters do not support mixed
mode interrupts among the functions of a given adapter.
Logic for setting MSI/MSI-x interrupt mode in the shared interrupt
register based on PCI function id zero check is not appropriate for
all family of netxen adapters, as for some of the netxen family
adapters PCI function zero is not really meant to be probed/loaded
in the host but rather just act as a management function on the device,
which caused all the other PCI functions on the adapter to always use
legacy interrupt (INTx) mode instead of choosing MSI/MSI-x interrupt mode.
This patch replaces that check with port number so that for all
type of adapters driver attempts for MSI/MSI-x interrupt modes.
Fixes: b37eb210c0 ("netxen_nic: Avoid mixed mode interrupts")
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Link: https://lore.kernel.org/r/20210107101520.6735-1-manishc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 53475c5dd8 ]
skbs in fraglist could be shared by a BPF filter loaded at TC. If TC
writes, it will call skb_ensure_writable -> pskb_expand_head to create
a private linear section for the head_skb. And then call
skb_clone_fraglist -> skb_get on each skb in the fraglist.
skb_segment_list overwrites part of the skb linear section of each
fragment itself. Even after skb_clone, the frag_skbs share their
linear section with their clone in PF_PACKET.
Both sk_receive_queue of PF_PACKET and PF_INET (or PF_INET6) can have
a link for the same frag_skbs chain. If a new skb (not frags) is
queued to one of the sk_receive_queue, multiple ptypes can see and
release this. It causes use-after-free.
[ 4443.426215] ------------[ cut here ]------------
[ 4443.426222] refcount_t: underflow; use-after-free.
[ 4443.426291] WARNING: CPU: 7 PID: 28161 at lib/refcount.c:190
refcount_dec_and_test_checked+0xa4/0xc8
[ 4443.426726] pstate: 60400005 (nZCv daif +PAN -UAO)
[ 4443.426732] pc : refcount_dec_and_test_checked+0xa4/0xc8
[ 4443.426737] lr : refcount_dec_and_test_checked+0xa0/0xc8
[ 4443.426808] Call trace:
[ 4443.426813] refcount_dec_and_test_checked+0xa4/0xc8
[ 4443.426823] skb_release_data+0x144/0x264
[ 4443.426828] kfree_skb+0x58/0xc4
[ 4443.426832] skb_queue_purge+0x64/0x9c
[ 4443.426844] packet_set_ring+0x5f0/0x820
[ 4443.426849] packet_setsockopt+0x5a4/0xcd0
[ 4443.426853] __sys_setsockopt+0x188/0x278
[ 4443.426858] __arm64_sys_setsockopt+0x28/0x38
[ 4443.426869] el0_svc_common+0xf0/0x1d0
[ 4443.426873] el0_svc_handler+0x74/0x98
[ 4443.426880] el0_svc+0x8/0xc
Fixes: 3a1296a38d (net: Support GRO/GSO fraglist chaining.)
Signed-off-by: Dongseok Yi <dseok.yi@samsung.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/r/1610072918-174177-1-git-send-email-dseok.yi@samsung.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit afba9dc1f3 ]
At the moment it is quite hard to identify the network interface
provided by IPA in userspace components: The network interface is
created as virtual device, without any link to the IPA device.
The interface name ("rmnet_ipa%d") is the only indication that the
network interface belongs to IPA, but this is not very reliable.
Add SET_NETDEV_DEV() to associate the network interface with the
IPA parent device. This allows userspace services like ModemManager
to properly identify that this network interface is provided by IPA
and belongs to the modem.
Cc: Alex Elder <elder@kernel.org>
Fixes: a646d6ec90 ("soc: qcom: ipa: modem and microcontroller")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210106100755.56800-1-stephan@gerhold.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 51b2ee7d00 upstream.
If you export a subdirectory of a filesystem, a READDIRPLUS on the root
of that export will return the filehandle of the parent with the ".."
entry.
The filehandle is optional, so let's just not return the filehandle for
".." if we're at the root of an export.
Note that once the client learns one filehandle outside of the export,
they can trivially access the rest of the export using further lookups.
However, it is also not very difficult to guess filehandles outside of
the export. So exporting a subdirectory of a filesystem should
considered equivalent to providing access to the entire filesystem. To
avoid confusion, we recommend only exporting entire filesystems.
Reported-by: Youjipeng <wangzhibei1999@gmail.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7178a107f5 upstream.
On the following call path, `sig->pkey_algo` is not assigned
in asymmetric_key_verify_signature(), which causes runtime
crash in public_key_verify_signature().
keyctl_pkey_verify
asymmetric_key_verify_signature
verify_signature
public_key_verify_signature
This patch simply check this situation and fixes the crash
caused by NULL pointer.
Fixes: 2155256396 ("X.509: support OSCCA SM2-with-SM3 certificate verification")
Reported-by: Tobias Markus <tobias@markus-regensburg.de>
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-and-tested-by: Toke Høiland-Jørgensen <toke@redhat.com>
Tested-by: João Fonseca <jpedrofonseca@ua.pt>
Acked-by: Jarkko Sakkinen <jarkko@kernel.org>
Cc: stable@vger.kernel.org # v5.10+
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bc895e8b2a upstream.
Fix incorrect signed_{sub,add32}_overflows() input types (and a related buggy
comment). It looks like this might have slipped in via copy/paste issue, also
given prior to 3f50f132d8 ("bpf: Verifier, do explicit ALU32 bounds tracking")
the signature of signed_sub_overflows() had s64 a and s64 b as its input args
whereas now they are truncated to s32. Thus restore proper types. Also, the case
of signed_add32_overflows() is not consistent to signed_sub32_overflows(). Both
have s32 as inputs, therefore align the former.
Fixes: 3f50f132d8 ("bpf: Verifier, do explicit ALU32 bounds tracking")
Reported-by: De4dCr0w <sa516203@mail.ustc.edu.cn>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c241ed2f0e upstream.
From Ard:
"Simply disabling -mgeneral-regs-only left and right is risky, given that
the standard AArch64 ABI permits the use of FP/SIMD registers anywhere,
and GCC is known to use SIMD registers for spilling, and may invent
other uses of the FP/SIMD register file that have nothing to do with the
floating point code in question. Note that putting kernel_neon_begin()
and kernel_neon_end() around the code that does use FP is not sufficient
here, the problem is in all the other code that may be emitted with
references to SIMD registers in it.
So the only way to do this properly is to put all floating point code in
a separate compilation unit, and only compile that unit with
-mgeneral-regs-only."
Disable support until the code can be properly refactored to support this
properly on aarch64.
Acked-by: Will Deacon <will@kernel.org>
Reported-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[ardb: backport to v5.10 by reverting c38d444e44 instead]
Acked-by: Alex Deucher <alexander.deucher@amd.com> # v5.10 backport
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fff7b5e6ee ]
With commit 4df4cb9e99, the Hyper-V direct-mode STIMER is actually
initialized before LAPIC is initialized: see
apic_intr_mode_init()
x86_platform.apic_post_init()
hyperv_init()
hv_stimer_alloc()
apic_bsp_setup()
setup_local_APIC()
setup_local_APIC() temporarily disables LAPIC, initializes it and
re-eanble it. The direct-mode STIMER depends on LAPIC, and when it's
registered, it can be programmed immediately and the timer can fire
very soon:
hv_stimer_init
clockevents_config_and_register
clockevents_register_device
tick_check_new_device
tick_setup_device
tick_setup_periodic(), tick_setup_oneshot()
clockevents_program_event
When the timer fires in the hypervisor, if the LAPIC is in the
disabled state, new versions of Hyper-V ignore the event and don't inject
the timer interrupt into the VM, and hence the VM hangs when it boots.
Note: when the VM starts/reboots, the LAPIC is pre-enabled by the
firmware, so the window of LAPIC being temporarily disabled is pretty
small, and the issue can only happen once out of 100~200 reboots for
a 40-vCPU VM on one dev host, and on another host the issue doesn't
reproduce after 2000 reboots.
The issue is more noticeable for kdump/kexec, because the LAPIC is
disabled by the first kernel, and stays disabled until the kdump/kexec
kernel enables it. This is especially an issue to a Generation-2 VM
(for which Hyper-V doesn't emulate the PIT timer) when CONFIG_HZ=1000
(rather than CONFIG_HZ=250) is used.
Fix the issue by moving hv_stimer_alloc() to a later place where the
LAPIC timer is initialized.
Fixes: 4df4cb9e99 ("x86/hyperv: Initialize clockevents earlier in CPU onlining")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/20210116223136.13892-1-decui@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit fb3558127c upstream.
Before this patch, profiler.inc.h wouldn't compile with clang-11 (before
the __builtin_preserve_enum_value LLVM builtin was introduced in
https://reviews.llvm.org/D83242).
Another test that uses this builtin (test_core_enumval) is conditionally
skipped if the compiler is too old. In that spirit, this patch inhibits
part of populate_cgroup_info(), which needs this CO-RE builtin. The
selftests build again on clang-11.
The affected test (the profiler test) doesn't pass on clang-11 because
it's missing https://reviews.llvm.org/D85570, but at least the test suite
as a whole compiles. The test's expected failure is already called out in
the README.
Signed-off-by: Andrei Matei <andreimatei1@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Florian Lehner <dev@der-flo.net>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20201125035255.17970-1-andreimatei1@gmail.com
Cc: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 869f4fdaf4 upstream.
When register_pernet_subsys() fails, nf_nat_bysource
should be freed just like when nf_ct_extend_register()
fails.
Fixes: 1cd472bf03 ("netfilter: nf_nat: add nat hook register functions to nf_nat")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f6351c3f1c upstream.
The old way of changing the conntrack hashsize runtime was through changing
the module param via file /sys/module/nf_conntrack/parameters/hashsize. This
was extended to sysctl change in commit 3183ab8997 ("netfilter: conntrack:
allow increasing bucket size via sysctl too").
The commit introduced second "user" variable nf_conntrack_htable_size_user
which shadow actual variable nf_conntrack_htable_size. When hashsize is
changed via module param this "user" variable isn't updated. This results in
sysctl net/netfilter/nf_conntrack_buckets shows the wrong value when users
update via the old way.
This patch fix the issue by always updating "user" variable when reading the
proc file. This will take care of changes to the actual variable without
sysctl need to be aware.
Fixes: 3183ab8997 ("netfilter: conntrack: allow increasing bucket size via sysctl too")
Reported-by: Yoel Caspersen <yoel@kviknet.dk>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9f65df9c58 upstream.
As snd_fw_async_midi_port.consume_bytes is unsigned int, and
NSEC_PER_SEC is 1000000000L, the second multiplication in
port->consume_bytes * 8 * NSEC_PER_SEC / 31250
always overflows on 32-bit platforms, truncating the result. Fix this
by precalculating "NSEC_PER_SEC / 31250", which is an integer constant.
Note that this assumes port->consume_bytes <= 16777.
Fixes: 531f471834 ("ALSA: firewire-lib/firewire-tascam: localize async midi port")
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210111130251.361335-3-geert+renesas@glider.be
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7c22eeaff upstream.
As snd_ff.rx_bytes[] is unsigned int, and NSEC_PER_SEC is 1000000000L,
the second multiplication in
ff->rx_bytes[port] * 8 * NSEC_PER_SEC / 31250
always overflows on 32-bit platforms, truncating the result. Fix this
by precalculating "NSEC_PER_SEC / 31250", which is an integer constant.
Note that this assumes ff->rx_bytes[port] <= 16777.
Fixes: 1917429578 ("ALSA: fireface: add transaction support")
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210111130251.361335-2-geert+renesas@glider.be
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0378c625af upstream.
There wasn't ever a real need to log an error in the kernel log for
ioctls issued with insufficient permissions. Simply return an error
and if an admin/user is sufficiently motivated they can enable DM's
dynamic debugging to see an explanation for why the ioctls were
disallowed.
Reported-by: Nir Soffer <nsoffer@redhat.com>
Fixes: e980f62353 ("dm: don't allow ioctls to targets that don't map to whole devices")
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fab336b424 upstream.
Fix nft_conntrack_helper.sh false fail report:
1) Conntrack tool need "-f ipv6" parameter to show out ipv6 traffic items.
2) Sleep 1 second after background nc send packet, to make sure check
is after this statement executed.
False report:
FAIL: ns1-lkjUemYw did not show attached helper ip set via ruleset
PASS: ns1-lkjUemYw connection on port 2121 has ftp helper attached
...
After fix:
PASS: ns1-2hUniwU2 connection on port 2121 has ftp helper attached
PASS: ns2-2hUniwU2 connection on port 2121 has ftp helper attached
...
Fixes: 619ae8e069 ("selftests: netfilter: add test case for conntrack helper assignment")
Signed-off-by: Chen Yi <yiche@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 86b53fbf08 upstream.
A return value of 0 means success. This is documented in lib/kstrtox.c.
This was found by trying to mount an NFS share from a link-local IPv6
address with the interface specified by its index:
mount("[fe80::1%1]:/srv/nfs", "/mnt", "nfs", 0, "nolock,addr=fe80::1%1")
Before this commit this failed with EINVAL and also caused the following
message in dmesg:
[...] NFS: bad IP address specified: addr=fe80::1%1
The syscall using the same address based on the interface name instead
of its index succeeds.
Credits for this patch go to my colleague Christian Speich, who traced
the origin of this bug to this line of code.
Signed-off-by: Johannes Nixdorf <j.nixdorf@avm.de>
Fixes: 00cfaa943e ("replace strict_strto calls")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2d6ffc63f1 upstream.
The VT-d hardware will ignore those Addr bits which have been masked by
the AM field in the PASID-based-IOTLB invalidation descriptor. As the
result, if the starting address in the descriptor is not aligned with
the address mask, some IOTLB caches might not invalidate. Hence people
will see below errors.
[ 1093.704661] dmar_fault: 29 callbacks suppressed
[ 1093.704664] DMAR: DRHD: handling fault status reg 3
[ 1093.712738] DMAR: [DMA Read] Request device [7a:02.0] PASID 2
fault addr 7f81c968d000 [fault reason 113]
SM: Present bit in first-level paging entry is clear
Fix this by using aligned address for PASID-based-IOTLB invalidation.
Fixes: 1c4f88b7f1 ("iommu/vt-d: Shared virtual address in scalable mode")
Reported-and-tested-by: Guo Kaijie <Kaijie.Guo@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20201231005323.2178523-2-baolu.lu@linux.intel.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ff60eb052 upstream.
acquire_slab() fails if there is contention on the freelist of the page
(probably because some other CPU is concurrently freeing an object from
the page). In that case, it might make sense to look for a different page
(since there might be more remote frees to the page from other CPUs, and
we don't want contention on struct page).
However, the current code accidentally stops looking at the partial list
completely in that case. Especially on kernels without CONFIG_NUMA set,
this means that get_partial() fails and new_slab_objects() falls back to
new_slab(), allocating new pages. This could lead to an unnecessary
increase in memory fragmentation.
Link: https://lkml.kernel.org/r/20201228130853.1871516-1-jannh@google.com
Fixes: 7ced371971 ("slub: Acquire_slab() avoid loop")
Signed-off-by: Jann Horn <jannh@google.com>
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 00cb645fd7 upstream.
Commit 25b4620ee8 ("drm/i915/dsi: Skip delays for v3 VBTs in vid-mode")
added an intel_dsi_msleep() helper which skips sleeping if the
MIPI-sequences have a version of 3 or newer and the panel is in vid-mode;
and it moved a bunch of msleep-s over to this new helper.
This was based on my reading of the big comment around line 730 which
starts with "Panel enable/disable sequences from the VBT spec.",
where the "v3 video mode seq" column does not have any wait t# entries.
Given that this code has been used on a lot of different devices without
issues until now, it seems that my interpretation of the spec here is
mostly correct.
But now I have encountered one device, an Acer Aspire Switch 10 E
SW3-016, where the panel will not light up unless we do actually honor the
panel_on_delay after exexuting the MIPI_SEQ_PANEL_ON sequence.
What seems to set this model apart is that it is lacking a
MIPI_SEQ_DEASSERT_RESET sequence, which is where the power-on
delay usually happens.
Fix the panel not lighting up on this model by using an unconditional
msleep(panel_on_delay) instead of intel_dsi_msleep() when there is
no MIPI_SEQ_DEASSERT_RESET sequence.
Fixes: 25b4620ee8 ("drm/i915/dsi: Skip delays for v3 VBTs in vid-mode")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201118124058.26021-1-hdegoede@redhat.com
(cherry picked from commit 6fdb335f1c)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b690bd546b upstream.
Without crc32 support, this driver fails to link:
arm-linux-gnueabi-ld: drivers/md/dm-zoned-metadata.o: in function `dmz_write_sb':
dm-zoned-metadata.c:(.text+0xe98): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/md/dm-zoned-metadata.o: in function `dmz_check_sb':
dm-zoned-metadata.c:(.text+0x7978): undefined reference to `crc32_le'
Fixes: 3b1a94c88b ("dm zoned: drive-managed zoned block device target")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a0a6df9afc upstream.
Unfortunately, there's userland code that used to rely upon these
checks being done before anything else to check for UMOUNT_NOFOLLOW
support. That broke in 41525f56e2 ("fs: refactor ksys_umount").
Separate those from the rest of checks and move them to ksys_umount();
unlike everything else in there, this can be sanely done there.
Reported-by: Sargun Dhillon <sargun@sargun.me>
Fixes: 41525f56e2 ("fs: refactor ksys_umount")
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 869c4d5eb1 upstream.
The function bnxt_get_ulp_stat_ctxs() does not count the stats contexts
used by the RDMA driver correctly when the RDMA driver is freeing the
MSIX vectors. It assumes that if the RDMA driver is registered, the
additional stats contexts will be needed. This is not true when the
RDMA driver is about to unregister and frees the MSIX vectors.
This slight error leads to over accouting of the stats contexts needed
after the RDMA driver has unloaded. This will cause some firmware
warning and error messages in dmesg during subsequent config. changes
or ifdown/ifup.
Fix it by properly accouting for extra stats contexts only if the
RDMA driver is registered and MSIX vectors have been successfully
requested.
Fixes: c027c6b4e9 ("bnxt_en: get rid of num_stat_ctxs variable")
Reviewed-by: Yongping Zhang <yongping.zhang@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c638cdb8e upstream.
xa_alloc_cyclic() call returns positive number if ID allocation
succeeded but wrapped. It is not an error, so normalize the "ret"
variable to zero as marker of not-an-error.
drivers/infiniband/core/restrack.c:261 rdma_restrack_add()
warn: 'ret' can be either negative or positive
Fixes: fd47c2f99f ("RDMA/restrack: Convert internal DB from hash to XArray")
Link: https://lore.kernel.org/r/20201216100753.1127638-1-leon@kernel.org
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d53864c36 upstream.
Currently if device needs to do flush or BKOP operations, the device VCC
power is kept during runtime-suspend period.
However, if system suspend is happening while device is runtime-suspended,
such power may not be disabled successfully.
The reasons may be,
1. If current PM level is the same as SPM level, device will keep
runtime-suspended by ufshcd_system_suspend().
2. Flush recheck work may not be scheduled successfully during system
suspend period. If it can wake up the system, this is also not the
intention of the recheck work.
To fix this issue, simply runtime-resume the device if the flush is allowed
during runtime suspend period. Flush capability will be disabled while
leaving runtime suspend, and also not be allowed in system suspend period.
Link: https://lore.kernel.org/r/20201222072905.32221-2-stanley.chu@mediatek.com
Fixes: 51dd905bd2 ("scsi: ufs: Fix WriteBooster flush during runtime suspend")
Reviewed-by: Chaotian Jing <chaotian.jing@mediatek.com>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 896567ee7f upstream.
Before referencing the inode, we must ensure that the superblock can be
referenced. Otherwise, we can end up with iput() calling superblock
operations that are no longer valid or accessible.
Fixes: ea7c38fef0 ("NFSv4: Ensure we reference the inode for return-on-close in delegreturn")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 113aac6d56 upstream.
Before referencing the inode, we must ensure that the superblock can be
referenced. Otherwise, we can end up with iput() calling superblock
operations that are no longer valid or accessible.
Fixes: e39d8a186e ("NFSv4: Fix an Oops during delegation callbacks")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cb2856c597 upstream.
If we exit _lgopen_prepare_attached() without setting a layout, we will
currently leak the plh_outstanding counter.
Fixes: 411ae722d1 ("pNFS: Wait for stale layoutget calls to complete in pnfs_update_layout()")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46c9ea1d4f upstream.
We must ensure that we pass a layout segment to nfs_retry_commit() when
we're cleaning up after pnfs_bucket_alloc_ds_commits(). Otherwise,
requests that should be committed to the DS will get committed to the
MDS.
Do so by ensuring that pnfs_bucket_get_committing() always tries to
return a layout segment when it returns a non-empty page list.
Fixes: c84bea5944 ("NFS/pNFS: Simplify bucket layout segment reference counting")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1757655d78 upstream.
In pnfs_generic_clear_request_commit(), we try calling
pnfs_free_bucket_lseg() before we remove the request from the DS bucket.
That will always fail, since the point is to test for whether or not
that bucket is empty.
Fixes: c84bea5944 ("NFS/pNFS: Simplify bucket layout segment reference counting")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c98e9daa59 upstream.
Several existing dprink()/dfprintk() calls were converted to use the new
mount API logging macros by commit ce8866f091 ("NFS: Attach
supplementary error information to fs_context"). If the fs_context was
not created using fsopen() then it will not have had a log buffer
allocated for it, and the new mount API logging macros will wind up
calling printk().
This can result in syslog messages being logged where previously there
were none... most notably "NFS4: Couldn't follow remote path", which can
happen if the client is auto-negotiating a protocol version with an NFS
server that doesn't support the higher v4.x versions.
Convert the nfs_errorf(), nfs_invalf(), and nfs_warnf() macros to check
for the existence of the fs_context's log buffer and call dprintk() if
it doesn't exist. Add nfs_ferrorf(), nfs_finvalf(), and nfs_warnf(),
which do the same thing but take an NFS debug flag as an argument and
call dfprintk(). Finally, modify the "NFS4: Couldn't follow remote
path" message to use nfs_ferrorf().
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=207385
Signed-off-by: Scott Mayhew <smayhew@redhat.com>
Reviewed-by: Benjamin Coddington <bcodding@redhat.com>
Fixes: ce8866f091 ("NFS: Attach supplementary error information to fs_context.")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c8d5fc37f upstream.
If a layout return is in progress, we should wait for it to complete,
in case the layout segment we are picking up gets returned too.
Fixes: 30cb3ee299 ("pNFS: Handle NFS4ERR_OLD_STATEID on layoutreturn by bumping the state seqid")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67bbceedc9 upstream.
If the layout return-on-close failed because the layoutreturn was never
sent, then we should mark the layout for return again.
Fixes: 9c47b18cf7 ("pNFS: Ensure we do clear the return-on-close layout stateid on fatal errors")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 078000d02d upstream.
If the inode is being evicted, it should be safe to run return-on-close,
so we should do it to ensure we don't inadvertently leak layout segments.
Fixes: 1c5bd76d17 ("pNFS: Enable layoutreturn operation for return-on-close")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d1a90ab0e upstream.
It is only safe to call the tracepoint before rpc_put_task() because
'data' is freed inside nfs4_lock_release (rpc_release).
Fixes: 48c9579a1a ("Adding stateid information to tracepoints")
Signed-off-by: Dave Wysochanski <dwysocha@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ada8317721 upstream.
We shouldn't call smp_processor_id() in a preemptible
context, but this is advisory at best, so instead
call __smp_processor_id().
Fixes: db5ad6b7f8 ("nvme-tcp: try to send request in queue_rq context")
Reported-by: Or Gerlitz <gerlitz.or@gmail.com>
Reported-by: Yi Zhang <yi.zhang@redhat.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca1ff67d0f upstream.
When a bio merges, we can get a request that spans multiple
bios, and the overall request payload size is the sum of
all bios. When we calculate how much we need to send
from the existing bio (and bvec), we did not take into
account the iov_iter byte count cap.
Since multipage bvecs support, bvecs can split in the middle
which means that when we account for the last bvec send we
should also take the iov_iter byte count cap as it might be
lower than the last bvec size.
Reported-by: Hao Wang <pkuwangh@gmail.com>
Fixes: 3f2304f8c6 ("nvme-tcp: add NVMe over TCP host driver")
Tested-by: Hao Wang <pkuwangh@gmail.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ab25a32cd upstream.
Discovery controllers usually don't support smart log page command.
So when we connect to the discovery controller we see this warning:
nvme nvme0: Failed to read smart log (error 24577)
nvme nvme0: new ctrl: NQN "nqn.2014-08.org.nvmexpress.discovery", addr 192.168.123.1:8009
nvme nvme0: Removing ctrl: NQN "nqn.2014-08.org.nvmexpress.discovery"
Introduce a new helper to understand if the controller is a discovery
controller and use this helper to skip nvme_init_hwmon (also use it in
other places that we check if the controller is a discovery controller).
Fixes: 400b6a7b13 ("nvme: Add hardware monitoring support")
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a84665619 upstream.
When setting port traddr to INADDR_ANY, the listening cm_id->device
is NULL. The associate IB device is known only when a connect request
event arrives, so checking T10-PI device capability should be done
at this stage.
Fixes: b09160c399 ("nvmet-rdma: add metadata/T10-PI support")
Signed-off-by: Israel Rukshin <israelr@nvidia.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 671ee4db95 upstream.
When the axg-tdm-interface was introduced, the backend DAI was marked as an
endpoint when DPCM was walking the DAPM graph to find a its BE.
It is no longer the case since this
commit 8dd26dff00 ("ASoC: dapm: Fix handling of custom_stop_condition on DAPM graph walks")
Because of this, when DPCM finds a BE it does everything it needs on the
DAIs but it won't power up the widgets between the FE and the BE if there
is no actual endpoint after the BE.
On meson-axg HWs, the loopback is a special DAI of the tdm-interface BE.
It is only linked to the dummy codec since there no actual HW after it.
>From the DAPM perspective, the DAI has no endpoint. Because of this, the TDM
decoder, which is a widget between the FE and BE is not powered up.
>From the user perspective, everything seems fine but no data is produced.
Connecting the Loopback DAI to a dummy DAPM endpoint solves the problem.
Fixes: 8dd26dff00 ("ASoC: dapm: Fix handling of custom_stop_condition on DAPM graph walks")
Cc: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20201217150812.3247405-1-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d36a1dd9f7 upstream.
We are not guaranteed the locking environment that would prevent
dentry getting renamed right under us. And it's possible for
old long name to be freed after rename, leading to UAF here.
Cc: stable@kernel.org # v2.6.2+
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5501e9229a upstream.
In some cases, the number of cpus (nr_cpus_online) is confused with the
maximum cpu number (nr_cpus_avail), which results in the error in the
example below:
Example on system with 8 cpus:
Before:
# echo 0 > /sys/devices/system/cpu/cpu2/online
# ./perf record --kcore -e intel_pt// taskset --cpu-list 7 uname
Linux
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.147 MB perf.data ]
# ./perf script --itrace=e
Requested CPU 7 too large. Consider raising MAX_NR_CPUS
0x25908 [0x8]: failed to process type: 68 [Invalid argument]
After:
# ./perf script --itrace=e
#
Fixes: 8c7274691f ("perf machine: Replace MAX_NR_CPUS with perf_env::nr_cpus_online")
Fixes: 7df4e36a47 ("perf session: Replace MAX_NR_CPUS with perf_env::nr_cpus_online")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Kan Liang <kan.liang@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: stable@vger.kernel.org
Link: http://lore.kernel.org/lkml/20210107174159.24897-1-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit feb889fb40 ]
So technically there is nothing wrong with adding a pinned page to the
swap cache, but the pinning obviously means that the page can't actually
be free'd right now anyway, so it's a bit pointless.
However, the real problem is not with it being a bit pointless: the real
issue is that after we've added it to the swap cache, we'll try to unmap
the page. That will succeed, because the code in mm/rmap.c doesn't know
or care about pinned pages.
Even the unmapping isn't fatal per se, since the page will stay around
in memory due to the pinning, and we do hold the connection to it using
the swap cache. But when we then touch it next and take a page fault,
the logic in do_swap_page() will map it back into the process as a
possibly read-only page, and we'll then break the page association on
the next COW fault.
Honestly, this issue could have been fixed in any of those other places:
(a) we could refuse to unmap a pinned page (which makes conceptual
sense), or (b) we could make sure to re-map a pinned page writably in
do_swap_page(), or (c) we could just make do_wp_page() not COW the
pinned page (which was what we historically did before that "mm:
do_wp_page() simplification" commit).
But while all of them are equally valid models for breaking this chain,
not putting pinned pages into the swap cache in the first place is the
simplest one by far.
It's also the safest one: the reason why do_wp_page() was changed in the
first place was that getting the "can I re-use this page" wrong is so
fraught with errors. If you do it wrong, you end up with an incorrectly
shared page.
As a result, using "page_maybe_dma_pinned()" in either do_wp_page() or
do_swap_page() would be a serious bug since it is only a (very good)
heuristic. Re-using the page requires a hard black-and-white rule with
no room for ambiguity.
In contrast, saying "this page is very likely dma pinned, so let's not
add it to the swap cache and try to unmap it" is an obviously safe thing
to do, and if the heuristic might very rarely be a false positive, no
harm is done.
Fixes: 09854ba94c ("mm: do_wp_page() simplification")
Reported-and-tested-by: Martin Raiber <martin@urbackup.org>
Cc: Pavel Begunkov <asml.silence@gmail.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Peter Xu <peterx@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9348b73c2e ]
Turning a pinned page read-only breaks the pinning after COW. Don't do it.
The whole "track page soft dirty" state doesn't work with pinned pages
anyway, since the page might be dirtied by the pinning entity without
ever being noticed in the page tables.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 29a951dfb3 ]
Turning page table entries read-only requires the mmap_sem held for
writing.
So stop doing the odd games with turning things from read locks to write
locks and back. Just get the write lock.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 02f938e9fe ]
Showing the hctx flags for when BLK_MQ_F_TAG_HCTX_SHARED is set gives
something like:
root@debian:/home/john# more /sys/kernel/debug/block/sda/hctx0/flags
alloc_policy=FIFO SHOULD_MERGE|TAG_QUEUE_SHARED|3
Add the decoding for that flag.
Fixes: 32bc15afed ("blk-mq: Facilitate a shared sbitmap per tagset")
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 25c904b59a ]
Adding vf VLANID for the first time, or after having cleared previously
defined VLANID works fine, however, attempting to change an existing vf
VLANID clears the rules on the firmware, but does not add new rules for
the new vf VLANID.
Fix this by changing the logic in function esw_acl_egress_lgcy_setup()
so that it will always configure egress rules.
Fixes: ea651a86d4 ("net/mlx5: E-Switch, Refactor eswitch egress acl codes")
Signed-off-by: Alaa Hleihel <alaa@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c4accc41c ]
Fix smatch warnings:
drivers/net/ethernet/mellanox/mlx5/core/esw/acl/egress_lgcy.c:105 esw_acl_egress_lgcy_setup() warn: passing zero to 'PTR_ERR'
drivers/net/ethernet/mellanox/mlx5/core/esw/acl/egress_ofld.c:177 esw_acl_egress_ofld_setup() warn: passing zero to 'PTR_ERR'
drivers/net/ethernet/mellanox/mlx5/core/esw/acl/ingress_lgcy.c:184 esw_acl_ingress_lgcy_setup() warn: passing zero to 'PTR_ERR'
drivers/net/ethernet/mellanox/mlx5/core/esw/acl/ingress_ofld.c:262 esw_acl_ingress_ofld_setup() warn: passing zero to 'PTR_ERR'
esw_acl_table_create() never returns NULL, so
NULL test should be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eed38eeee7 ]
Connection counters may be shared for both directions when the counter
is used for connection aging purposes. However, if TC flow
accounting is enabled then a unique counter is required per direction.
Instantiate a unique counter per direction if the conntrack accounting
extension is enabled. Use a shared counter when the connection accounting
extension is disabled.
Fixes: 1edae2335a ("net/mlx5e: CT: Use the same counter for both directions")
Signed-off-by: Oz Shlomo <ozsh@nvidia.com>
Reported-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 19fce0470f ]
Recent patches changed calling sequences. nvme_fc_abort_outstanding_ios
used to be called from a timeout or work context. Now it is being called
in an io completion context, which can be an interrupt handler.
Unfortunately, the abort outstanding ios routine attempts to stop nvme
queues and nested routines that may try to sleep, which is in conflict
with the interrupt handler.
Correct replacing the direct call with a work element scheduling, and the
abort outstanding ios routine will be called in the work element.
Fixes: 95ced8a2c7 ("nvme-fc: eliminate terminate_io use by nvme_fc_error_recovery")
Signed-off-by: James Smart <james.smart@broadcom.com>
Reported-by: Daniel Wagner <dwagner@suse.de>
Tested-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 152a8a6c01 ]
Without crc32 support, this fails to link:
arm-linux-gnueabi-ld: net/wireless/scan.o: in function `cfg80211_scan_6ghz':
scan.c:(.text+0x928): undefined reference to `crc32_le'
Fixes: c8cb5b854b ("nl80211/cfg80211: support 6 GHz scanning")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a8f7e08a81 ]
The IN and OUT instructions with port address as an immediate operand
only use an 8-bit immediate (imm8). The current VC handler uses the
entire 32-bit immediate value but these instructions only set the first
bytes.
Cast the operand to an u8 for that.
[ bp: Massage commit message. ]
Fixes: 25189d08e5 ("x86/sev-es: Add support for handling IOIO exceptions")
Signed-off-by: Peter Gonda <pgonda@google.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: David Rientjes <rientjes@google.com>
Link: https://lkml.kernel.org/r/20210105163311.221490-1-pgonda@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b04fa9900 ]
PowerPC testing encountered boot failures due to RCU Tasks not being
fully initialized until core_initcall() time. This commit therefore
initializes RCU Tasks (along with Rude RCU and RCU Tasks Trace) just
before early_initcall() time, thus allowing waiting on RCU Tasks grace
periods from early_initcall() handlers.
Link: https://lore.kernel.org/rcu/87eekfh80a.fsf@dja-thinkpad.axtens.net/
Fixes: 36dadef23f ("kprobes: Init kprobes in early_initcall")
Tested-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef0ba05538 ]
The kernel test robot reported a -5.8% performance regression on the
"poll2" test of will-it-scale, and bisected it to commit d55564cfc2
("x86: Make __put_user() generate an out-of-line call").
I didn't expect an out-of-line __put_user() to matter, because no normal
core code should use that non-checking legacy version of user access any
more. But I had overlooked the very odd poll() usage, which does a
__put_user() to update the 'revents' values of the poll array.
Now, Al Viro correctly points out that instead of updating just the
'revents' field, it would be much simpler to just copy the _whole_
pollfd entry, and then we could just use "copy_to_user()" on the whole
array of entries, the same way we use "copy_from_user()" a few lines
earlier to get the original values.
But that is not what we've traditionally done, and I worry that threaded
applications might be concurrently modifying the other fields of the
pollfd array. So while Al's suggestion is simpler - and perhaps worth
trying in the future - this instead keeps the "just update revents"
model.
To fix the performance regression, use the modern "unsafe_put_user()"
instead of __put_user(), with the proper "user_write_access_begin()"
guarding in place. This improves code generation enormously.
Link: https://lore.kernel.org/lkml/20210107134723.GA28532@xsang-OptiPlex-9020/
Reported-by: kernel test robot <oliver.sang@intel.com>
Tested-by: Oliver Sang <oliver.sang@intel.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: David Laight <David.Laight@aculab.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee61cfd955 ]
It adds a stub acpi_create_platform_device() for !CONFIG_ACPI build, so
that caller doesn't have to deal with !CONFIG_ACPI build issue.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 420d42f6f9 ]
Lock(&iommu->lock) without disabling irq causes lockdep warnings.
========================================================
WARNING: possible irq lock inversion dependency detected
5.11.0-rc1+ #828 Not tainted
--------------------------------------------------------
kworker/0:1H/120 just changed the state of lock:
ffffffffad9ea1b8 (device_domain_lock){..-.}-{2:2}, at:
iommu_flush_dev_iotlb.part.0+0x32/0x120
but this lock took another, SOFTIRQ-unsafe lock in the past:
(&iommu->lock){+.+.}-{2:2}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&iommu->lock);
local_irq_disable();
lock(device_domain_lock);
lock(&iommu->lock);
<Interrupt>
lock(device_domain_lock);
*** DEADLOCK ***
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20201231005323.2178523-5-baolu.lu@linux.intel.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ceb786353 ]
When a queue is in NVMET_RDMA_Q_CONNECTING state, it may has some
requests at rsp_wait_list. In case a disconnect occurs at this
state, no one will empty this list and will return the requests to
free_rsps list. Normally nvmet_rdma_queue_established() free those
requests after moving the queue to NVMET_RDMA_Q_LIVE state, but in
this case __nvmet_rdma_queue_disconnect() is called before. The
crash happens at nvmet_rdma_free_rsps() when calling
list_del(&rsp->free_list), because the request exists only at
the wait list. To fix the issue, simply clear rsp_wait_list when
destroying the queue.
Signed-off-by: Israel Rukshin <israelr@nvidia.com>
Reviewed-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62df80165d ]
While handling the completion queue, keep a local copy of the command id
from the DMA-accessible completion entry. This silences a time-of-check
to time-of-use (TOCTOU) warning from KF/x[1], with respect to a
Thunderclap[2] vulnerability analysis. The double-read impact appears
benign.
There may be a theoretical window for @command_id to be used as an
adversary-controlled array-index-value for mounting a speculative
execution attack, but that mitigation is saved for a potential follow-on.
A man-in-the-middle attack on the data payload is out of scope for this
analysis and is hopefully mitigated by filesystem integrity mechanisms.
[1] https://github.com/intel/kernel-fuzzer-for-xen-project
[2] http://thunderclap.io/thunderclap-paper-ndss2019.pdf
Signed-off-by: Lalithambika Krishna Kumar <lalithambika.krishnakumar@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ee5c78ca3 ]
A system with more than one of these SSDs will only have one usable.
Hence the kernel fails to detect nvme devices due to duplicate cntlids.
[ 6.274554] nvme nvme1: Duplicate cntlid 33 with nvme0, rejecting
[ 6.274566] nvme nvme1: Removing after probe failure status: -22
Adding the NVME_QUIRK_IGNORE_DEV_SUBNQN quirk to resolves the issue.
Signed-off-by: Gopal Tiwari <gtiwari@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3503ee6c0b ]
The udpgro.sh will always return 0 (unless the bpf selftest was not
build first) even if there are some failed sub test-cases.
Therefore the kselftest framework will report this case is OK.
Check and return the exit status of each test to make it easier to
spot real failures.
Signed-off-by: Po-Hsu Lin <po-hsu.lin@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 445c6198fe ]
Since commit 1d6cd39293 ("modpost: turn missing MODULE_LICENSE()
into error") the ppc32_allmodconfig build fails with:
ERROR: modpost: missing MODULE_LICENSE() in drivers/net/ethernet/freescale/fs_enet/mii-fec.o
ERROR: modpost: missing MODULE_LICENSE() in drivers/net/ethernet/freescale/fs_enet/mii-bitbang.o
Add the missing MODULE_LICENSEs to fix the build. Both files include a
copyright header indicating they are GPL v2.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51049bd903 ]
Without this, we run into a link error
arm-linux-gnueabi-ld: drivers/isdn/mISDN/dsp_audio.o: in function `dsp_audio_generate_law_tables':
(.text+0x30c): undefined reference to `byte_rev_table'
arm-linux-gnueabi-ld: drivers/isdn/mISDN/dsp_audio.o:(.text+0x5e4): more undefined references to `byte_rev_table' follow
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d4d273588 ]
BFQ computes number of tags it allows to be allocated for each request type
based on tag bitmap. However it uses 1 << bitmap.shift as number of
available tags which is wrong. 'shift' is just an internal bitmap value
containing logarithm of how many bits bitmap uses in each bitmap word.
Thus number of tags allowed for some request types can be far to low.
Use proper bitmap.depth which has the number of tags instead.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de7f1d9e99 ]
io_uring fds marked O_CLOEXEC and we explicitly cancel all requests
before going through exec, so we don't want to leave task's file
references to not our anymore io_uring instances.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c36d88cff ]
Older versions of BSD awk are fussy about the order of '-v' and '-f'
flags, and require a space after the flag name. This causes build
failures on platforms with an old awk, such as macOS and NetBSD.
Since GNU awk and modern versions of BSD awk (distributed with
FreeBSD/OpenBSD) are fine with either form, the definition of
'cmd_unroll' can be trivially tweaked to let the lib/raid6 Makefile
work with both old and new awk flag dialects.
Signed-off-by: John Millikin <john@john-millikin.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1eda52334e ]
With MAX_PWM being defined to 255 the code
unsigned long period;
...
period = ctx->pwm->args.period;
state.duty_cycle = DIV_ROUND_UP(pwm * (period - 1), MAX_PWM);
calculates a too small value for duty_cycle if the configured period is
big (either by discarding the 64 bit value ctx->pwm->args.period or by
overflowing the multiplication). As this results in a too slow fan and
so maybe an overheating machine better be safe than sorry and error out
in .probe.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20201215092031.152243-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b000700d6d ]
When kzalloc() fails, we should execute hl_mmu_fini()
to release the MMU module. It's the same when
hl_ctx_init() fails.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ede090f5a4 ]
This patch fixes the return value for altera_spi_txrx. It should return
1 for interrupt transfer mode, and return 0 for polling transfer mode.
The altera_spi_txrx() implements the spi_controller.transfer_one
callback. According to the spi-summary.rst, the transfer_one should
return 0 when transfer is finished, return 1 when transfer is still in
progress.
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
Link: https://lore.kernel.org/r/1609219662-27057-2-git-send-email-yilun.xu@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fcaebc7354 ]
We need to make sure our device is idle when rebooting a virtual
machine. This is done in the driver level.
The firmware will later handle FLR but we want to be extra safe and
stop the devices until the FLR is handled.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 98e8781f00 ]
If loading the firmware file for the TPC f/w was interrupted, try
to do it again, up to 5 times.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 377182a3cc ]
When the firmware security is enabled, the pcie_aux_dbi_reg_addr
register in the PCI controller is blocked. Therefore, ignore
the result of writing to this register and assume it worked. Also
remove the prints on errors in the internal ELBI write function.
If the security is enabled, the firmware is responsible for setting
this register correctly so we won't have any problem.
If the security is disabled, the write will work (unless something
is totally broken at the PCI level and then the whole sequence
will fail).
In addition, remove a write to register pcie_aux_dbi_reg_addr+4,
which was never actually needed.
Moreover, PCIE_DBI registers are blocked to access from host when
firmware security is enabled. Use a different register to flush the
writes.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 887078de2a ]
Table 8-53 in the QUICC Engine Reference manual shows definitions of
fields up to a size of 192 bytes, not just 128. But in table 8-111,
one does find the text
Base Address of the Global Transmitter Parameter RAM Page. [...]
The user needs to allocate 128 bytes for this page. The address must
be aligned to the page size.
I've checked both rev. 7 (11/2015) and rev. 9 (05/2018) of the manual;
they both have this inconsistency (and the table numbers are the
same).
Adding a bit of debug printing, on my board the struct
ucc_geth_tx_global_pram is allocated at offset 0x880, while
the (opaque) ucc_geth_thread_data_tx gets allocated immediately
afterwards, at 0x900. So whatever the engine writes into the thread
data overlaps with the tail of the global tx pram (and devmem says
that something does get written during a simple ping).
I haven't observed any failure that could be attributed to this, but
it seems to be the kind of thing that would be extremely hard to
debug. So extend the struct definition so that we do allocate 192
bytes.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8fc058597a ]
btrfs_discard_workfn() drops discard_ctl->lock just to take it again in
a moment in btrfs_discard_schedule_work(). Avoid that and also reuse
ktime.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea9ed87c73 ]
Might happen that bg->discard_eligible_time was changed without
rescheduling, so btrfs_discard_workfn() wakes up earlier than that new
time, peek_discard_list() returns NULL, and all work halts and goes to
sleep without further rescheduling even there are block groups to
discard.
It happens pretty often, but not so visible from the userspace because
after some time it usually will be kicked off anyway by someone else
calling btrfs_discard_reschedule_work().
Fix it by continue rescheduling if block group discard lists are not
empty.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f6f92968e1 ]
Not all firmware versions support allocating DMA memory in smaller blocks so
first try to allocate big block of DMA memory for QMI. If the allocation fails,
let firmware request multiple blocks of DMA memory with smaller size.
This also fixes an unnecessary error message seen during ath11k probe on
QCA6390:
ath11k_pci 0000:06:00.0: Respond mem req failed, result: 1, err: 0
ath11k_pci 0000:06:00.0: qmi failed to respond fw mem req:-22
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1608127593-15192-1-git-send-email-kvalo@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2b33d6ffa9 ]
currently mtype_resize() can cause oops
t = ip_set_alloc(htable_size(htable_bits));
if (!t) {
ret = -ENOMEM;
goto out;
}
t->hregion = ip_set_alloc(ahash_sizeof_regions(htable_bits));
Increased htable_bits can force htable_size() to return 0.
In own turn ip_set_alloc(0) returns not 0 but ZERO_SIZE_PTR,
so follwoing access to t->hregion should trigger an OOPS.
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Acked-by: Jozsef Kadlecsik <kadlec@netfilter.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c0bc969c17 ]
xt875 comes up with a iva voltage of 1375000 and android runs at this too. fix
maximum voltage to be consistent with this.
Signed-off-by: Carl Philipp Klemm <philipp@uvos.xyz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c5e6ae563c ]
If you run 'make uImage uImage.gz' with the parallel option, uImage.gz
will be created by two threads simultaneously.
This is because arch/arc/Makefile does not specify the dependency
between uImage and uImage.gz. Hence, GNU Make assumes they can be
built in parallel. One thread descends into arch/arc/boot/ to create
uImage, and another to create uImage.gz.
Please notice the same log is displayed twice in the following steps:
$ export CROSS_COMPILE=<your-arc-compiler-prefix>
$ make -s ARCH=arc defconfig
$ make -j$(nproc) ARCH=arc uImage uImage.gz
[ snip ]
LD vmlinux
SORTTAB vmlinux
SYSMAP System.map
OBJCOPY arch/arc/boot/vmlinux.bin
OBJCOPY arch/arc/boot/vmlinux.bin
GZIP arch/arc/boot/vmlinux.bin.gz
GZIP arch/arc/boot/vmlinux.bin.gz
UIMAGE arch/arc/boot/uImage.gz
UIMAGE arch/arc/boot/uImage.gz
Image Name: Linux-5.10.0-rc4-00003-g62f23044
Created: Sun Nov 22 02:52:26 2020
Image Type: ARC Linux Kernel Image (gzip compressed)
Data Size: 2109376 Bytes = 2059.94 KiB = 2.01 MiB
Load Address: 80000000
Entry Point: 80004000
Image arch/arc/boot/uImage is ready
Image Name: Linux-5.10.0-rc4-00003-g62f23044
Created: Sun Nov 22 02:52:26 2020
Image Type: ARC Linux Kernel Image (gzip compressed)
Data Size: 2815455 Bytes = 2749.47 KiB = 2.69 MiB
Load Address: 80000000
Entry Point: 80004000
This is a race between the two threads trying to write to the same file
arch/arc/boot/uImage.gz. This is a potential problem that can generate
a broken file.
I fixed a similar problem for ARM by commit 3939f33450 ("ARM: 8418/1:
add boot image dependencies to not generate invalid images").
I highly recommend to avoid such build rules that cause a race condition.
Move the uImage rule to arch/arc/Makefile.
Another strangeness is that arch/arc/boot/Makefile compares the
timestamps between $(obj)/uImage and $(obj)/uImage.*:
$(obj)/uImage: $(obj)/uImage.$(suffix-y)
@ln -sf $(notdir $<) $@
@echo ' Image $@ is ready'
This does not work as expected since $(obj)/uImage is a symlink.
The symlink should be created in a phony target rule.
I used $(kecho) instead of echo to suppress the message
'Image arch/arc/boot/uImage is ready' when the -s option is given.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0cfccb3c04 ]
The top-level boot_targets (uImage and uImage.*) should be phony
targets. They just let Kbuild descend into arch/arc/boot/ and create
files there.
If a file exists in the top directory with the same name, the boot
image will not be created.
You can confirm it by the following steps:
$ export CROSS_COMPILE=<your-arc-compiler-prefix>
$ make -s ARCH=arc defconfig all # vmlinux will be built
$ touch uImage.gz
$ make ARCH=arc uImage.gz
CALL scripts/atomic/check-atomics.sh
CALL scripts/checksyscalls.sh
CHK include/generated/compile.h
# arch/arc/boot/uImage.gz is not created
Specify the targets as PHONY to fix this.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2712ec76a ]
arch/arc/boot/Makefile supports uImage.lzma, but you cannot do
'make uImage.lzma' because the corresponding target is missing
in arch/arc/Makefile. Add it.
I also changed the assignment operator '+=' to ':=' since this is the
only place where we expect this variable to be set.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9836720911 ]
The deb-pkg builds for ARCH=arc fail.
$ export CROSS_COMPILE=<your-arc-compiler-prefix>
$ make -s ARCH=arc defconfig
$ make ARCH=arc bindeb-pkg
SORTTAB vmlinux
SYSMAP System.map
MODPOST Module.symvers
make KERNELRELEASE=5.10.0-rc4 ARCH=arc KBUILD_BUILD_VERSION=2 -f ./Makefile intdeb-pkg
sh ./scripts/package/builddeb
cp: cannot stat 'arch/arc/boot/bootpImage': No such file or directory
make[4]: *** [scripts/Makefile.package:87: intdeb-pkg] Error 1
make[3]: *** [Makefile:1527: intdeb-pkg] Error 2
make[2]: *** [debian/rules:13: binary-arch] Error 2
dpkg-buildpackage: error: debian/rules binary subprocess returned exit status 2
make[1]: *** [scripts/Makefile.package:83: bindeb-pkg] Error 2
make: *** [Makefile:1527: bindeb-pkg] Error 2
The reason is obvious; arch/arc/Makefile sets $(boot)/bootpImage as
the default image, but there is no rule to build it.
Remove the meaningless KBUILD_IMAGE assignment so it will fallback
to the default vmlinux. With this change, you can build the deb package.
I removed the 'bootpImage' target as well. At best, it provides
'make bootpImage' as an alias of 'make vmlinux', but I do not see
much sense in doing so.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d434ab6db5 ]
__io_req_task_submit() run by task_work can set mm and files, but
io_sq_thread() in some cases, and because __io_sq_thread_acquire_mm()
and __io_sq_thread_acquire_files() do a simple current->mm/files check
it may end up submitting IO with mm/files of another task.
We also need to drop it after in the end to drop potentially grabbed
references to them.
Cc: stable@vger.kernel.org # 5.9+
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 621fadc223 ]
In rare cases a task may be exiting while io_ring_exit_work() trying to
cancel/wait its requests. It's ok for __io_sq_thread_acquire_mm()
because of SQPOLL check, but is not for __io_sq_thread_acquire_files().
Play safe and fail for both of them.
Cc: stable@vger.kernel.org # 5.5+
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a3b590d4b ]
When the first file is opened, ext4 samples the mountpoint of the
filesystem in 64 bytes of the super block. It does so using
strlcpy(), this means that the remaining bytes in the super block
string buffer are untouched. If the mount point before had a longer
path than the current one, it can be reconstructed.
Consider the case where the fs was mounted to "/media/johnjdeveloper"
and later to "/". The super block buffer then contains
"/\x00edia/johnjdeveloper".
This case was seen in the wild and caused confusion how the name
of a developer ands up on the super block of a filesystem used
in production...
Fix this by using strncpy() instead of strlcpy(). The superblock
field is defined to be a fixed-size char array, and it is already
marked using __nonstring in fs/ext4/ext4.h. The consumer of the field
in e2fsprogs already assumes that in the case of a 64+ byte mount
path, that s_last_mounted will not be NUL terminated.
Link: https://lore.kernel.org/r/X9ujIOJG/HqMr88R@mit.edu
Reported-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit cb82a54904 upstream.
This USB-C Hub (17ef:721e) based on the Realtek RTL8153B chip used to
use the cdc_ether driver. However, using this driver, with the system
suspended the device constantly sends pause-frames as soon as the
receive buffer fills up. This causes issues with other devices, where
some Ethernet switches stop forwarding packets altogether.
Using the Realtek driver (r8152) fixes this issue. Pause frames are no
longer sent while the host system is suspended.
Signed-off-by: Leon Schuermann <leon@is.currently.online>
Tested-by: Leon Schuermann <leon@is.currently.online>
Link: https://lore.kernel.org/r/20210111190312.12589-2-leon@is.currently.online
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e14f61015 upstream.
Sometimes, when dm-crypt executes decryption in a tasklet, we may get
"BUG: KASAN: use-after-free in tasklet_action_common.constprop..."
with a kasan-enabled kernel.
When the decryption fully completes in the tasklet, dm-crypt will call
bio_endio(), which in turn will call clone_endio() from dm.c core code. That
function frees the resources associated with the bio, including per bio private
structures. For dm-crypt it will free the current struct dm_crypt_io, which
contains our tasklet object, causing use-after-free, when the tasklet is being
dequeued by the kernel.
To avoid this, do not call bio_endio() from the current tasklet context, but
delay its execution to the dm-crypt IO workqueue.
Fixes: 39d42fa96b ("dm crypt: add flags to optionally bypass kcryptd workqueues")
Cc: <stable@vger.kernel.org> # v5.9+
Signed-off-by: Ignat Korchagin <ignat@cloudflare.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 17ffc193cd upstream.
Advance the maximum number of arguments from 9 to 15 to account for
all potential feature flags that may be supplied.
Linux 4.19 added "meta_device"
(356d9d52e1) and "recalculate"
(a3fcf72531) flags.
Commit 468dfca38b added
"sectors_per_bit" and "bitmap_flush_interval".
Commit 84597a44a9 added
"allow_discards".
And the commit d537858ac8 added
"fix_padding".
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b5948267a upstream.
With external metadata device, flush requests are not passed down to the
data device.
Fix this by submitting the flush request in dm_integrity_flush_buffers. In
order to not degrade performance, we overlap the data device flush with
the metadata device flush.
Reported-by: Lukas Straub <lukasstraub2@web.de>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fcc4233837 upstream.
If the origin device has a volatile write-back cache and the following
events occur:
1: After finishing merge operation of one set of exceptions,
merge_callback() is invoked.
2: Update the metadata in COW device tracking the merge completion.
This update to COW device is flushed cleanly.
3: System crashes and the origin device's cache where the recent
merge was completed has not been flushed.
During the next cycle when we read the metadata from the COW device,
we will skip reading those metadata whose merge was completed in
step (1). This will lead to data loss/corruption.
To address this, flush the origin device post merge IO before
updating the metadata.
Cc: stable@vger.kernel.org
Signed-off-by: Akilesh Kailash <akailash@google.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc07d72bf3 upstream.
Block core warned that discard_granularity was 0 for dm-raid with
personality of raid1. Reason is that raid_io_hints() was incorrectly
special-casing raid1 rather than raid0.
Fix raid_io_hints() by removing discard limits settings for
raid1. Check for raid0 instead.
Fixes: 61697a6abd ("dm: eliminate 'split_discard_bios' flag from DM target interface")
Cc: stable@vger.kernel.org
Reported-by: Zdenek Kabelac <zkabelac@redhat.com>
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Reported-by: Stephan Bärwolf <stephan@matrixstorm.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a58015d638 upstream.
Linux VM on Hyper-V crashes with the latest mainline:
[ 4.069624] detected buffer overflow in strcpy
[ 4.077733] kernel BUG at lib/string.c:1149!
..
[ 4.085819] RIP: 0010:fortify_panic+0xf/0x11
...
[ 4.085819] Call Trace:
[ 4.085819] acpi_device_add.cold.15+0xf2/0xfb
[ 4.085819] acpi_add_single_object+0x2a6/0x690
[ 4.085819] acpi_bus_check_add+0xc6/0x280
[ 4.085819] acpi_ns_walk_namespace+0xda/0x1aa
[ 4.085819] acpi_walk_namespace+0x9a/0xc2
[ 4.085819] acpi_bus_scan+0x78/0x90
[ 4.085819] acpi_scan_init+0xfa/0x248
[ 4.085819] acpi_init+0x2c1/0x321
[ 4.085819] do_one_initcall+0x44/0x1d0
[ 4.085819] kernel_init_freeable+0x1ab/0x1f4
This is because of the recent buffer overflow detection in the
commit 6a39e62abb ("lib: string.h: detect intra-object overflow in
fortified string functions")
Here acpi_device_bus_id->bus_id can only hold 14 characters, while the
the acpi_device_hid(device) returns a 22-char string
"HYPER_V_GEN_COUNTER_V1".
Per ACPI Spec v6.2, Section 6.1.5 _HID (Hardware ID), if the ID is a
string, it must be of the form AAA#### or NNNN####, i.e. 7 chars or 8
chars.
The field bus_id in struct acpi_device_bus_id was originally defined as
char bus_id[9], and later was enlarged to char bus_id[15] in 2007 in the
commit bb0958544f ("ACPI: use more understandable bus_id for ACPI
devices")
Fix the issue by changing the field bus_id to const char *, and use
kstrdup_const() to initialize it.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Tested-By: Jethro Beekman <jethro@fortanix.com>
[ rjw: Subject change, whitespace adjustment ]
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 69e976831c upstream.
LLVM-built Linux triggered a boot hangup with KASLR enabled.
arch/mips/kernel/relocate.c:get_random_boot() uses linux_banner,
which is a string constant, as a random seed, but accesses it
as an array of unsigned long (in rotate_xor()).
When the address of linux_banner is not aligned to sizeof(long),
such access emits unaligned access exception and hangs the kernel.
Use PTR_ALIGN() to align input address to sizeof(long) and also
align down the input length to prevent possible access-beyond-end.
Fixes: 405bc8fd12 ("MIPS: Kernel: Implement KASLR using CONFIG_RELOCATABLE")
Cc: stable@vger.kernel.org # 4.7+
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6982224574 upstream.
Patches that introduced NT_FILE and NT_SIGINFO notes back in 2012
had taken care of native (fs/binfmt_elf.c) and compat (fs/compat_binfmt_elf.c)
coredumps; unfortunately, compat on mips (which does not go through the
usual compat_binfmt_elf.c) had not been noticed.
As the result, both N32 and O32 coredumps on 64bit mips kernels
have those sections malformed enough to confuse the living hell out of
all gdb and readelf versions (up to and including the tip of binutils-gdb.git).
Longer term solution is to make both O32 and N32 compat use the
regular compat_binfmt_elf.c, but that's too much for backports. The minimal
solution is to do in arch/mips/kernel/binfmt_elf[on]32.c the same thing
those patches have done in fs/compat_binfmt_elf.c
Cc: stable@kernel.org # v3.7+
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4d4f9c1a17 upstream.
The compressed payload is not necesarily 4-byte aligned, at least when
compiling with Clang. In that case, the 4-byte value appended to the
compressed payload that corresponds to the uncompressed kernel image
size must be read using get_unaligned_le32().
This fixes Clang-built kernels not booting on MIPS (tested on a Ingenic
JZ4770 board).
Fixes: b8f54f2cde ("MIPS: ZBOOT: copy appended dtb to the end of the kernel")
Cc: <stable@vger.kernel.org> # v4.7
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b058973d3 upstream.
When building mips tinyconfig with clang the following warning show up:
arch/mips/lib/uncached.c:45:6: warning: variable 'sp' is uninitialized when used here [-Wuninitialized]
if (sp >= (long)CKSEG0 && sp < (long)CKSEG2)
^~
arch/mips/lib/uncached.c:40:18: note: initialize the variable 'sp' to silence this warning
register long sp __asm__("$sp");
^
= 0
1 warning generated.
Rework to make an explicit inline move, instead of the non-standard use
of specifying registers for local variables. This is what's written
from the gcc-10 manual [1] about specifying registers for local
variables:
"6.47.5.2 Specifying Registers for Local Variables
.................................................
[...]
"The only supported use for this feature is to specify registers for
input and output operands when calling Extended 'asm' (*note Extended
Asm::). [...]".
[1] https://docs.w3cub.com/gcc~10/local-register-variables
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ad4fddef5f upstream.
When building mips tinyconfig with clang the following error show up:
WARNING: modpost: vmlinux.o(.text+0x1940c): Section mismatch in reference from the function r4k_cache_init() to the function .init.text:loongson3_sc_init()
The function r4k_cache_init() references
the function __init loongson3_sc_init().
This is often because r4k_cache_init lacks a __init
annotation or the annotation of loongson3_sc_init is wrong.
Remove marked __init from function loongson3_sc_init(),
mips_sc_probe_cm3(), and mips_sc_probe().
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0aa2ec8a47 upstream.
The patch fix commit: ad5d112 ("riscv: use vDSO common flow to
reduce the latency of the time-related functions").
The GENERIC_TIME_VSYSCALL should be CONFIG_GENERIC_TIME_VSYSCALL
or vgettimeofday won't work.
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Reviewed-by: Pekka Enberg <penberg@kernel.org>
Fixes: ad5d1122b8 ("riscv: use vDSO common flow to reduce the latency of the time-related functions")
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 77b6ec01c2 upstream.
clang static analysis reports this problem
dfs_cache.c:591:2: warning: Argument to kfree() is a constant address
(18446744073709551614), which is not memory allocated by malloc()
kfree(vi);
^~~~~~~~~
In dfs_cache_del_vol() the volume info pointer 'vi' being freed
is the return of a call to find_vol(). The large constant address
is find_vol() returning an error.
Add an error check to dfs_cache_del_vol() similar to the one done
in dfs_cache_update_vol().
Fixes: 54be1f6c1c ("cifs: Add DFS cache routines")
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
CC: <stable@vger.kernel.org> # v5.0+
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b4b8e6b4a upstream.
We got a "deleted inode referenced" warning cross our fsstress test. The
bug can be reproduced easily with following steps:
cd /dev/shm
mkdir test/
fallocate -l 128M img
mkfs.ext4 -b 1024 img
mount img test/
dd if=/dev/zero of=test/foo bs=1M count=128
mkdir test/dir/ && cd test/dir/
for ((i=0;i<1000;i++)); do touch file$i; done # consume all block
cd ~ && renameat2(AT_FDCWD, /dev/shm/test/dir/file1, AT_FDCWD,
/dev/shm/test/dir/dst_file, RENAME_WHITEOUT) # ext4_add_entry in
ext4_rename will return ENOSPC!!
cd /dev/shm/ && umount test/ && mount img test/ && ls -li test/dir/file1
We will get the output:
"ls: cannot access 'test/dir/file1': Structure needs cleaning"
and the dmesg show:
"EXT4-fs error (device loop0): ext4_lookup:1626: inode #2049: comm ls:
deleted inode referenced: 139"
ext4_rename will create a special inode for whiteout and use this 'ino'
to replace the source file's dir entry 'ino'. Once error happens
latter(the error above was the ENOSPC return from ext4_add_entry in
ext4_rename since all space has been consumed), the cleanup do drop the
nlink for whiteout, but forget to restore 'ino' with source file. This
will trigger the bug describle as above.
Signed-off-by: yangerkun <yangerkun@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: stable@vger.kernel.org
Fixes: cd808deced ("ext4: support RENAME_WHITEOUT")
Link: https://lore.kernel.org/r/20210105062857.3566-1-yangerkun@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc5f7e2fcb upstream.
On the SII9022, the IOVCC and CVCC12 supplies must reach the correct
voltage before the reset sequence is initiated. On most boards, this
assumption is true at boot-up, so initialization succeeds.
However, when we try to initialize the chip with incorrect supply
voltages, it will not respond to I2C requests. sii902x_probe() fails
with -ENXIO.
To resolve this, look for the "iovcc" and "cvcc12" regulators, and
make sure they are enabled before starting the reset sequence. If
these supplies are not available in devicetree, then they will default
to dummy-regulator. In that case everything will work like before.
This was observed on a STM32MP157C-DK2 booting in u-boot falcon mode.
On this board, the supplies would be set by the second stage
bootloader, which does not run in falcon mode.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
[Fix checkpatch warnings]
Link: https://patchwork.freedesktop.org/patch/msgid/20201020221501.260025-2-mr.nuke.me@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb83d5fb55 upstream.
The pch_get_backlight(), lpt_get_backlight(), and lpt_set_backlight()
functions operate directly on the hardware registers. If inverting the
value is needed, using intel_panel_compute_brightness(), it should only
be done in the interface between hardware registers and
panel->backlight.level.
The CPU mode takeover code added in commit 5b1ec9ac7a
("drm/i915/backlight: Fix backlight takeover on LPT, v3.") reads the
hardware register and converts to panel->backlight.level correctly,
however the value written back should remain in the hardware register
"domain".
This hasn't been an issue, because GM45 machines are the only known
users of i915.invert_brightness and the brightness invert quirk, and
without one of them no conversion is made. It's likely nobody's ever hit
the problem.
Fixes: 5b1ec9ac7a ("drm/i915/backlight: Fix backlight takeover on LPT, v3.")
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: <stable@vger.kernel.org> # v5.1+
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210108152841.6944-1-jani.nikula@intel.com
(cherry picked from commit 0d4ced1c5b)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ad0a6bad44 upstream.
We've observed crashes due to an empty cpu mask in
hyperv_flush_tlb_others. Obviously the cpu mask in question is changed
between the cpumask_empty call at the beginning of the function and when
it is actually used later.
One theory is that an interrupt comes in between and a code path ends up
changing the mask. Move the check after interrupt has been disabled to
see if it fixes the issue.
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Cc: stable@kernel.org
Link: https://lore.kernel.org/r/20210105175043.28325-1-wei.liu@kernel.org
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c6679b5cb upstream.
A widget's "dirty" list_head, much like its "list" list_head, eventually
chains back to a list_head on the snd_soc_card itself. This means that
the list can stick around even after the widget (or all widgets) have
been freed. Currently, however, widgets that are in the dirty list when
freed remain there, corrupting the entire list and leading to memory
errors and undefined behavior when the list is next accessed or
modified.
I encountered this issue when a component failed to probe relatively
late in snd_soc_bind_card(), causing it to bail out and call
soc_cleanup_card_resources(), which eventually called
snd_soc_dapm_free() with widgets that were still dirty from when they'd
been added.
Fixes: db432b414e ("ASoC: Do DAPM power checks only for widgets changed since last run")
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/f8b5f031d50122bf1a9bfc9cae046badf4a7a31a.1607822410.git.tommyhebb@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 50e31ef486 upstream.
[BUG]
There are several bug reports about recent kernel unable to relocate
certain data block groups.
Sometimes the error just goes away, but there is one reporter who can
reproduce it reliably.
The dmesg would look like:
[438.260483] BTRFS info (device dm-10): balance: start -dvrange=34625344765952..34625344765953
[438.269018] BTRFS info (device dm-10): relocating block group 34625344765952 flags data|raid1
[450.439609] BTRFS info (device dm-10): found 167 extents, stage: move data extents
[463.501781] BTRFS info (device dm-10): balance: ended with status: -2
[CAUSE]
The ENOENT error is returned from the following call chain:
add_data_references()
|- delete_v1_space_cache();
|- if (!found)
return -ENOENT;
The variable @found is set to true if we find a data extent whose
disk bytenr matches parameter @data_bytes.
With extra debugging, the offending tree block looks like this:
leaf bytenr = 42676709441536, data_bytenr = 34626327621632
ctime 1567904822.739884119 (2019-09-08 03:07:02)
mtime 0.0 (1970-01-01 01:00:00)
otime 0.0 (1970-01-01 01:00:00)
item 27 key (51933 EXTENT_DATA 0) itemoff 9854 itemsize 53
generation 1517381 type 2 (prealloc)
prealloc data disk byte 34626327621632 nr 262144 <<<
prealloc data offset 0 nr 262144
item 28 key (52262 ROOT_ITEM 0) itemoff 9415 itemsize 439
generation 2618893 root_dirid 256 bytenr 42677048360960 level 3 refs 1
lastsnap 2618893 byte_limit 0 bytes_used 5557338112 flags 0x0(none)
uuid d0d4361f-d231-6d40-8901-fe506e4b2b53
Although item 27 has disk bytenr 34626327621632, which matches the
data_bytenr, its type is prealloc, not reg.
This makes the existing code skip that item, and return ENOENT.
[FIX]
The code is modified in commit 19b546d7a1 ("btrfs: relocation: Use
btrfs_find_all_leafs to locate data extent parent tree leaves"), before
that commit, we use something like
"if (type == BTRFS_FILE_EXTENT_INLINE) continue;"
But in that offending commit, we use (type == BTRFS_FILE_EXTENT_REG),
ignoring BTRFS_FILE_EXTENT_PREALLOC.
Fix it by also checking BTRFS_FILE_EXTENT_PREALLOC.
Reported-by: Stéphane Lesimple <stephane_btrfs2@lesimple.fr>
Link: https://lore.kernel.org/linux-btrfs/505cabfa88575ed6dbe7cb922d8914fb@lesimple.fr
Fixes: 19b546d7a1 ("btrfs: relocation: Use btrfs_find_all_leafs to locate data extent parent tree leaves")
CC: stable@vger.kernel.org # 5.6+
Tested-By: Stéphane Lesimple <stephane_btrfs2@lesimple.fr>
Reviewed-by: Su Yue <l@damenly.su>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a443a5177 upstream.
To pick the changes from:
3ceb6543e9 ("fscrypt: remove kernel-internal constants from UAPI header")
That don't result in any changes in tooling, just addressing this perf
build warning:
Warning: Kernel ABI header at 'tools/include/uapi/linux/fscrypt.h' differs from latest version at 'include/uapi/linux/fscrypt.h'
diff -u tools/include/uapi/linux/fscrypt.h include/uapi/linux/fscrypt.h
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Eric Biggers <ebiggers@google.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f6bcb4c7f3 upstream.
This code will leak "map->debugfs_name" because the if statement is
reversed so it only frees NULL pointers instead of non-NULL. In
fact the if statement is not required and should just be removed
because kfree() accepts NULL pointers.
Fixes: cffa4b2122 ("regmap: debugfs: Fix a memory leak when calling regmap_attach_dev")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/X/RQpfAwRdLg0GqQ@mwanda
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a21777c6e upstream.
We had kernel panic, it is caused by unload module and last
close confirmation.
call trace:
[1196029.743127] free_sess+0x15/0x50 [rtrs_client]
[1196029.743128] rtrs_clt_close+0x4c/0x70 [rtrs_client]
[1196029.743129] ? rnbd_clt_unmap_device+0x1b0/0x1b0 [rnbd_client]
[1196029.743130] close_rtrs+0x25/0x50 [rnbd_client]
[1196029.743131] rnbd_client_exit+0x93/0xb99 [rnbd_client]
[1196029.743132] __x64_sys_delete_module+0x190/0x260
And in the crashdump confirmation kworker is also running.
PID: 6943 TASK: ffff9e2ac8098000 CPU: 4 COMMAND: "kworker/4:2"
#0 [ffffb206cf337c30] __schedule at ffffffff9f93f891
#1 [ffffb206cf337cc8] schedule at ffffffff9f93fe98
#2 [ffffb206cf337cd0] schedule_timeout at ffffffff9f943938
#3 [ffffb206cf337d50] wait_for_completion at ffffffff9f9410a7
#4 [ffffb206cf337da0] __flush_work at ffffffff9f08ce0e
#5 [ffffb206cf337e20] rtrs_clt_close_conns at ffffffffc0d5f668 [rtrs_client]
#6 [ffffb206cf337e48] rtrs_clt_close at ffffffffc0d5f801 [rtrs_client]
#7 [ffffb206cf337e68] close_rtrs at ffffffffc0d26255 [rnbd_client]
#8 [ffffb206cf337e78] free_sess at ffffffffc0d262ad [rnbd_client]
#9 [ffffb206cf337e88] rnbd_clt_put_dev at ffffffffc0d266a7 [rnbd_client]
The problem is both code path try to close same session, which lead to
panic.
To fix it, just skip the sess if the refcount already drop to 0.
Fixes: f7a7a5c228 ("block/rnbd: client: main functionality")
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Reviewed-by: Gioh Kim <gi-oh.kim@cloud.ionos.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b1b95cb5c0 upstream.
Rollback the reservation in the completion ring when we get a
NETDEV_TX_BUSY. When this error is received from the driver, we are
supposed to let the user application retry the transmit again. And in
order to do this, we need to roll back the failed send so it can be
retried. Unfortunately, we did not cancel the reservation we had made
in the completion ring. By not doing this, we actually make the
completion ring one entry smaller per NETDEV_TX_BUSY error we get, and
after enough of these errors the completion ring will be of size zero
and transmit will stop working.
Fix this by cancelling the reservation when we get a NETDEV_TX_BUSY
error.
Fixes: 642e450b6b ("xsk: Do not discard packet when NETDEV_TX_BUSY")
Reported-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/bpf/20201218134525.13119-3-magnus.karlsson@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f09ced4053 upstream.
Fix a race when multiple sockets are simultaneously calling sendto()
when the completion ring is shared in the SKB case. This is the case
when you share the same netdev and queue id through the
XDP_SHARED_UMEM bind flag. The problem is that multiple processes can
be in xsk_generic_xmit() and call the backpressure mechanism in
xskq_prod_reserve(xs->pool->cq). As this is a shared resource in this
specific scenario, a race might occur since the rings are
single-producer single-consumer.
Fix this by moving the tx_completion_lock from the socket to the pool
as the pool is shared between the sockets that share the completion
ring. (The pool is not shared when this is not the case.) And then
protect the accesses to xskq_prod_reserve() with this lock. The
tx_completion_lock is renamed cq_lock to better reflect that it
protects accesses to the potentially shared completion ring.
Fixes: 35fcde7f8d ("xsk: support for Tx")
Reported-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/bpf/20201218134525.13119-2-magnus.karlsson@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a5f1b67ec upstream.
We reset the guest's view of PMCR_EL0 unconditionally, based on
the host's view of this register. It is however legal for an
implementation not to provide any PMU, resulting in an UNDEF.
The obvious fix is to skip the reset of this shadow register
when no PMU is available, sidestepping the issue entirely.
If no PMU is available, the guest is not able to request
a virtual PMU anyway, so not doing nothing is the right thing
to do!
It is unlikely that this bug can hit any HW implementation
though, as they all provide a PMU. It has been found using nested
virt with the host KVM not implementing the PMU itself.
Fixes: ab9468340d ("arm64: KVM: Add access handler for PMCR register")
Reviewed-by: Alexandru Elisei <alexandru.elisei@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20201210083059.1277162-1-maz@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a5c9ca76a1 upstream.
For IPv6 traffic, mausezahn needs to be invoked with '-6'. Otherwise an
error is returned:
# ip netns exec me mausezahn veth1 -B 2001:db8:101::2 -A 2001:db8:91::1 -c 0 -t tcp "dp=1-1023, flags=syn"
Failed to set source IPv4 address. Please check if source is set to a valid IPv4 address.
Invalid command line parameters!
Fixes: 7c741868ce ("selftests: Add torture tests to nexthop tests")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 69931e1128 upstream.
Without this, the driver runs into a link failure
arm-linux-gnueabi-ld: drivers/net/wan/slic_ds26522.o: in function `slic_ds26522_probe':
slic_ds26522.c:(.text+0x100c): undefined reference to `byte_rev_table'
arm-linux-gnueabi-ld: slic_ds26522.c:(.text+0x1cdc): undefined reference to `byte_rev_table'
arm-linux-gnueabi-ld: drivers/net/wan/slic_ds26522.o: in function `slic_write':
slic_ds26522.c:(.text+0x1e4c): undefined reference to `byte_rev_table'
Fixes: c37d4a0085 ("Maxim/driver: Add driver for maxim ds26522")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cffa4b2122 upstream.
After initializing the regmap through
syscon_regmap_lookup_by_compatible, then regmap_attach_dev to the
device, because the debugfs_name has been allocated, there is no
need to redistribute it again
unreferenced object 0xd8399b80 (size 64):
comm "swapper/0", pid 1, jiffies 4294937641 (age 278.590s)
hex dump (first 32 bytes):
64 75 6d 6d 79 2d 69 6f 6d 75 78 63 2d 67 70 72
dummy-iomuxc-gpr
40 32 30 65 34 30 30 30 00 7f 52 5b d8 7e 42 69
@20e4000..R[.~Bi
backtrace:
[<ca384d6f>] kasprintf+0x2c/0x54
[<6ad3bbc2>] regmap_debugfs_init+0xdc/0x2fc
[<bc4181da>] __regmap_init+0xc38/0xd88
[<1f7e0609>] of_syscon_register+0x168/0x294
[<735e8766>] device_node_get_regmap+0x6c/0x98
[<d96c8982>] imx6ul_init_machine+0x20/0x88
[<0456565b>] customize_machine+0x1c/0x30
[<d07393d8>] do_one_initcall+0x80/0x3ac
[<7e584867>] kernel_init_freeable+0x170/0x1f0
[<80074741>] kernel_init+0x8/0x120
[<285d6f28>] ret_from_fork+0x14/0x20
[<00000000>] 0x0
Fixes: 9b947a13e7 ("regmap: use debugfs even when no device")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Link: https://lore.kernel.org/r/20201229105046.41984-1-xiaolei.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a6eb072a9 upstream.
mlx5e_create_ttc_table_groups() frees ft->g on failure of
kvzalloc(), but such failure will be caught by its caller
in mlx5e_create_ttc_table() and ft->g will be freed again
in mlx5e_destroy_flow_table(). The same issue also occurs
in mlx5e_create_ttc_table_groups(). Set ft->g to NULL after
kfree() to avoid double free.
Fixes: 7b3722fa9e ("net/mlx5e: Support RSS for GRE tunneled packets")
Fixes: 33cfaaa8f3 ("net/mlx5e: Split the main flow steering table")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b0bb12c58 upstream.
When mlx5_create_flow_group() fails, ft->g should be
freed just like when kvzalloc() fails. The caller of
mlx5e_create_l2_table_groups() does not catch this
issue on failure, which leads to memleak.
Fixes: 33cfaaa8f3 ("net/mlx5e: Split the main flow steering table")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c11f7d9f8 upstream.
We may send a request (with or without its data) from two paths:
1. From our I/O context nvme_tcp_io_work which is triggered from:
- queue_rq
- r2t reception
- socket data_ready and write_space callbacks
2. Directly from queue_rq if the send_list is empty (because we want to
save the context switch associated with scheduling our io_work).
However, given that now we have the send_mutex, we may run into a race
condition where none of these contexts will send the pending payload to
the controller. Both io_work send path and queue_rq send path
opportunistically attempt to acquire the send_mutex however queue_rq only
attempts to send a single request, and if io_work context fails to
acquire the send_mutex it will complete without rescheduling itself.
The race can trigger with the following sequence:
1. queue_rq sends request (no incapsule data) and blocks
2. RX path receives r2t - prepares data PDU to send, adds h2cdata PDU
to the send_list and schedules io_work
3. io_work triggers and cannot acquire the send_mutex - because of (1),
ends without self rescheduling
4. queue_rq completes the send, and completes
==> no context will send the h2cdata - timeout.
Fix this by having queue_rq sending as much as it can from the send_list
such that if it still has any left, its because the socket buffer is
full and the socket write_space callback will trigger, thus guaranteeing
that a context will be scheduled to send the h2cdata PDU.
Fixes: db5ad6b7f8 ("nvme-tcp: try to send request in queue_rq context")
Reported-by: Potnuri Bharat Teja <bharat@chelsio.com>
Reported-by: Samuel Jones <sjones@kalrayinc.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Tested-by: Potnuri Bharat Teja <bharat@chelsio.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f8b848788 upstream.
When CRC32 is disabled, zonefs cannot be linked:
ld: fs/zonefs/super.o: in function `zonefs_fill_super':
Add a Kconfig 'select' statement for it.
Fixes: 8dcc1a9d90 ("fs: New zonefs file system")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e186620d7b upstream.
Without crc32, the driver fails to link:
arm-linux-gnueabi-ld: drivers/net/wireless/ath/wil6210/fw.o: in function `wil_fw_verify':
fw.c:(.text+0x74c): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/wireless/ath/wil6210/fw.o:fw.c:(.text+0x758): more undefined references to `crc32_le' follow
Fixes: 151a970650 ("wil6210: firmware download")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9d6f94132 upstream.
Without crc32, this driver fails to link:
arm-linux-gnueabi-ld: drivers/net/phy/dp83640.o: in function `match':
dp83640.c:(.text+0x476c): undefined reference to `crc32_le'
Fixes: 539e44d268 ("dp83640: Include hash in timestamp/packet matching")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2860d45a58 upstream.
Without this, the driver fails to link:
lpc_eth.c:(.text+0x1934): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/qlogic/qed/qed_debug.o: in function `qed_grc_dump':
qed_debug.c:(.text+0x4068): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/qlogic/qed/qed_debug.o: in function `qed_idle_chk_dump':
qed_debug.c:(.text+0x51fc): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/qlogic/qed/qed_debug.o: in function `qed_mcp_trace_dump':
qed_debug.c:(.text+0x6000): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/qlogic/qed/qed_debug.o: in function `qed_dbg_reg_fifo_dump':
qed_debug.c:(.text+0x66cc): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/qlogic/qed/qed_debug.o:qed_debug.c:(.text+0x6aa4): more undefined references to `crc32_le' follow
Fixes: 7a4b21b7d1 ("qed: Add nvram selftest")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 095507dc13 upstream.
Systems configured with CONFIG_ZONE_DMA32, CONFIG_ZONE_NORMAL and
!CONFIG_ZONE_DMA will fail to properly setup ARCH_LOW_ADDRESS_LIMIT. The
limit will default to ~0ULL, effectively spanning the whole memory,
which is too high for a configuration that expects low memory to be
capped at 4GB.
Fix ARCH_LOW_ADDRESS_LIMIT by falling back to arm64_dma32_phys_limit
when arm64_dma_phys_limit isn't set. arm64_dma32_phys_limit will honour
CONFIG_ZONE_DMA32, or span the entire memory when not enabled.
Fixes: 1a8e1cef76 ("arm64: use both ZONE_DMA and ZONE_DMA32")
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20201218163307.10150-1-nsaenzjulienne@suse.de
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 512d4a26ab upstream.
When CONFIG_COMPILE_TEST is set, it is possible to build some
of the interconnect drivers into the kernel while their dependencies
are loadable modules, which is bad:
arm-linux-gnueabi-ld: drivers/interconnect/qcom/bcm-voter.o: in function `qcom_icc_bcm_voter_commit':
(.text+0x1f8): undefined reference to `rpmh_invalidate'
arm-linux-gnueabi-ld: (.text+0x20c): undefined reference to `rpmh_write_batch'
arm-linux-gnueabi-ld: (.text+0x2b0): undefined reference to `rpmh_write_batch'
arm-linux-gnueabi-ld: (.text+0x2e8): undefined reference to `rpmh_write_batch'
arm-linux-gnueabi-ld: drivers/interconnect/qcom/icc-rpmh.o: in function `qcom_icc_bcm_init':
(.text+0x2ac): undefined reference to `cmd_db_read_addr'
arm-linux-gnueabi-ld: (.text+0x2c8): undefined reference to `cmd_db_read_aux_data'
The exact dependencies are a bit complicated, so split them out into a
hidden Kconfig symbol that all drivers can in turn depend on to get it
right.
Fixes: 976daac4a1 ("interconnect: qcom: Consolidate interconnect RPMh support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20201204165030.3747484-1-arnd@kernel.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5342fd4255 upstream.
If BCH_FEATURE_INCOMPAT_OBSO_LARGE_BUCKET is set in incompat feature
set, it means the cache device is created with obsoleted layout with
obso_bucket_site_hi. Now bcache does not support this feature bit, a new
BCH_FEATURE_INCOMPAT_LOG_LARGE_BUCKET_SIZE incompat feature bit is added
for a better layout to support large bucket size.
For the legacy compatibility purpose, if a cache device created with
obsoleted BCH_FEATURE_INCOMPAT_OBSO_LARGE_BUCKET feature bit, all bcache
devices attached to this cache set should be set to read-only. Then the
dirty data can be written back to backing device before re-create the
cache device with BCH_FEATURE_INCOMPAT_LOG_LARGE_BUCKET_SIZE feature bit
by the latest bcache-tools.
This patch checks BCH_FEATURE_INCOMPAT_OBSO_LARGE_BUCKET feature bit
when running a cache set and attach a bcache device to the cache set. If
this bit is set,
- When run a cache set, print an error kernel message to indicate all
following attached bcache device will be read-only.
- When attach a bcache device, print an error kernel message to indicate
the attached bcache device will be read-only, and ask users to update
to latest bcache-tools.
Such change is only for cache device whose bucket size >= 32MB, this is
for the zoned SSD and almost nobody uses such large bucket size at this
moment. If you don't explicit set a large bucket size for a zoned SSD,
such change is totally transparent to your bcache device.
Fixes: ffa4703275 ("bcache: add bucket_size_hi into struct cache_sb_disk for large bucket")
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05f6f7271a upstream.
With the apdma remove hand-shake signal, it requirs special
operation timing to reset i2c manually, otherwise the interrupt
will not be triggered, i2c transmission will be timeout.
Fixes: 8426fe70cfa4("i2c: mediatek: Add apdma sync in i2c driver")
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a590370d91 upstream.
if cur_bpw <= 8 and xfer_len < 4 then the value of fthlv will be 1 and
SPI registers content may have been lost.
* If SPI data register is accessed as a 16-bit register and DSIZE <= 8bit,
better to select FTHLV = 2, 4, 6 etc
* If SPI data register is accessed as a 32-bit register and DSIZE > 8bit,
better to select FTHLV = 2, 4, 6 etc, while if DSIZE <= 8bit,
better to select FTHLV = 4, 8, 12 etc
Signed-off-by: Roman Guskov <rguskov@dh-electronics.com>
Fixes: dcbe0d84df ("spi: add driver for STM32 SPI controller")
Reviewed-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20201221123532.27272-1-rguskov@dh-electronics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4aa1464acb upstream.
In commit 7ba9bdcb91 ("spi: spi-geni-qcom: Don't keep a local state
variable") we changed handle_fifo_timeout() so that we set
"mas->cur_xfer" to NULL to make absolutely sure that we don't mess
with the buffers from the previous transfer in the timeout case.
Unfortunately, this caused the IRQ handler to dereference NULL in some
cases. One case:
CPU0 CPU1
---- ----
setup_fifo_xfer()
geni_se_setup_m_cmd()
<hardware starts transfer>
<transfer completes in hardware>
<hardware sets M_RX_FIFO_WATERMARK_EN in m_irq>
...
handle_fifo_timeout()
spin_lock_irq(mas->lock)
mas->cur_xfer = NULL
geni_se_cancel_m_cmd()
spin_unlock_irq(mas->lock)
geni_spi_isr()
spin_lock(mas->lock)
if (m_irq & M_RX_FIFO_WATERMARK_EN)
geni_spi_handle_rx()
mas->cur_xfer NULL dereference!
tl;dr: Seriously delayed interrupts for RX/TX can lead to timeout
handling setting mas->cur_xfer to NULL.
Let's check for the NULL transfer in the TX and RX cases and reset the
watermark or clear out the fifo respectively to put the hardware back
into a sane state.
NOTE: things still could get confused if we get timeouts all the way
through handle_fifo_timeout() and then start a new transfer because
interrupts from the old transfer / cancel / abort could still be
pending. A future patch will help this corner case.
Fixes: 561de45f72 ("spi: spi-geni-qcom: Add SPI driver support for GENI based QUP")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20201217142842.v3.1.I99ee04f0cb823415df59bd4f550d6ff5756e43d6@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 943bdd0cec upstream.
Currently there is an unlikely case where cpufreq_cpu_get() returns a
NULL policy and this will cause a NULL pointer dereference later on.
Fix this by passing the policy to transition_frequency_fidvid() from
the caller and hence eliminating the need for the cpufreq_cpu_get()
and cpufreq_cpu_put().
Thanks to Viresh Kumar for suggesting the fix.
Addresses-Coverity: ("Dereference null return")
Fixes: b43a7ffbf3 ("cpufreq: Notify all policy->cpus in cpufreq_notify_transition()")
Suggested-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 690d8b917b upstream.
If we got a timeout when trying to send an abort command then it means
that we just got 3 timeouts in a row:
1. The original timeout that caused handle_fifo_timeout() to be
called.
2. A one second timeout waiting for the cancel command to finish.
3. A one second timeout waiting for the abort command to finish.
SPI is clocked by the controller, so nothing (aside from a hardware
fault or a totally broken sequencer) should be causing the actual
commands to fail in hardware. However, even though the hardware
itself is not expected to fail (and it'd be hard to predict how we
should handle things if it did), it's easy to hit the timeout case by
simply blocking our interrupt handler from running for a long period
of time. Obviously the system is in pretty bad shape if a interrupt
handler is blocked for > 2 seconds, but there are certainly bugs (even
bugs in other unrelated drivers) that can make this happen.
Let's make things a bit more robust against this case. If we fail to
abort we'll set a flag and then we'll block all future transfers until
we have no more interrupts pending.
Fixes: 561de45f72 ("spi: spi-geni-qcom: Add SPI driver support for GENI based QUP")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20201217142842.v3.2.Ibade998ed587e070388b4bf58801f1107a40eb53@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d48595c78 upstream.
Without crc32, this driver fails to link:
arm-linux-gnueabi-ld: drivers/net/can/kvaser_pciefd.o: in function `kvaser_pciefd_probe':
kvaser_pciefd.c:(.text+0x2b0): undefined reference to `crc32_be'
Fixes: 26ad340e58 ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aee2b3ccc8 upstream.
According to the TCAN4550 datasheet "SLLSF91 - DECEMBER 2018" the tcan4x5x has
the same bittiming constants as a m_can revision 3.2.x/3.3.0.
The tcan4x5x chip I'm using identifies itself as m_can revision 3.2.1, so
remove the tcan4x5x specific bittiming values and rely on the values in the
m_can driver, which are selected according to core revision.
Fixes: 5443c226ba ("can: tcan4x5x: Add tcan4x5x driver to the kernel")
Cc: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215103238.524029-3-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a3449c194 upstream.
If Makefile cannot find any of the vmlinux's in its VMLINUX_BTF_PATHS list,
it tries to run btftool incorrectly, with VMLINUX_BTF unset:
bpftool btf dump file $(VMLINUX_BTF) format c
Such that the keyword 'format' is misinterpreted as the path to vmlinux.
The resulting build error message is fairly cryptic:
GEN vmlinux.h
Error: failed to load BTF from format: No such file or directory
This patch makes the failure reason clearer by yielding this instead:
Makefile:...: *** Cannot find a vmlinux for VMLINUX_BTF at any of
"{paths}". Stop.
Fixes: acbd06206b ("selftests/bpf: Add vmlinux.h selftest exercising tracing of syscalls")
Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20201215182011.15755-1-kamal@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 595a334148 upstream.
If the dw_edma_alloc_burst() function fails then we free "chunk" but
it's still on the "desc->chunk->list" list so it will lead to a use
after free. Also the "->chunks_alloc" count is incremented when it
shouldn't be.
In current kernels small allocations are guaranteed to succeed and
dw_edma_alloc_burst() can't fail so this will not actually affect
runtime.
Fixes: e63d79d1ff ("dmaengine: Add Synopsys eDMA IP core driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Link: https://lore.kernel.org/r/X9dTBFrUPEvvW7qc@mwanda
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0b884fe71f upstream.
If the i2c device SCL bus being pulled up due to some exception before
message transfer done, the system cannot receive the completing interrupt
signal any more, it would not exit waiting loop until MAX_SCHEDULE_TIMEOUT
jiffies eclipse, that would make the system seemed hang up. To avoid that
happen, this patch adds a specific timeout for message transfer.
Fixes: 8b9ec07198 ("i2c: Add Spreadtrum I2C controller driver")
Signed-off-by: Linhua Xu <linhua.xu@unisoc.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
[wsa: changed errno to ETIMEDOUT]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ec76c2eea9 upstream.
On the GTA04A5 od->_driver_status was not set to BUS_NOTIFY_BIND_DRIVER
during probe of the second mmc used for wifi. Therefore
omap_device_late_idle idled the device during probing causing oopses when
accessing the registers.
It was not set because od->_state was set to OMAP_DEVICE_STATE_IDLE
in the notifier callback. Therefore set od->_driver_status also in that
case.
This came apparent after commit 21b2cec61c ("mmc: Set
PROBE_PREFER_ASYNCHRONOUS for drivers that existed in v4.4") causing this
oops:
omap_hsmmc 480b4000.mmc: omap_device_late_idle: enabled but no driver. Idling
8<--- cut here ---
Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa0b402c
...
(omap_hsmmc_set_bus_width) from [<c07996bc>] (omap_hsmmc_set_ios+0x11c/0x258)
(omap_hsmmc_set_ios) from [<c077b2b0>] (mmc_power_up.part.8+0x3c/0xd0)
(mmc_power_up.part.8) from [<c077c14c>] (mmc_start_host+0x88/0x9c)
(mmc_start_host) from [<c077d284>] (mmc_add_host+0x58/0x84)
(mmc_add_host) from [<c0799190>] (omap_hsmmc_probe+0x5fc/0x8c0)
(omap_hsmmc_probe) from [<c0666728>] (platform_drv_probe+0x48/0x98)
(platform_drv_probe) from [<c066457c>] (really_probe+0x1dc/0x3b4)
Fixes: 04abaf07f6 ("ARM: OMAP2+: omap_device: Sync omap_device and pm_runtime after probe defer")
Fixes: 21b2cec61c ("mmc: Set PROBE_PREFER_ASYNCHRONOUS for drivers that existed in v4.4")
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
[tony@atomide.com: left out extra parens, trimmed description stack trace]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2ca408d9c7 upstream.
Commit
121b32a58a ("x86/entry/32: Use IA32-specific wrappers for syscalls taking 64-bit arguments")
converted native x86-32 which take 64-bit arguments to use the
compat handlers to allow conversion to passing args via pt_regs.
sys_fanotify_mark() was however missed, as it has a general compat
handler. Add a config option that will use the syscall wrapper that
takes the split args for native 32-bit.
[ bp: Fix typo in Kconfig help text. ]
Fixes: 121b32a58a ("x86/entry/32: Use IA32-specific wrappers for syscalls taking 64-bit arguments")
Reported-by: Paweł Jasiak <pawel@jasiak.xyz>
Signed-off-by: Brian Gerst <brgerst@gmail.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Jan Kara <jack@suse.cz>
Acked-by: Andy Lutomirski <luto@kernel.org>
Link: https://lkml.kernel.org/r/20201130223059.101286-1-brgerst@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f56bc4dc1 upstream.
Change the order of operations in the link_up handling to be
sure that the queues are up and ready before we announce that
the link is up.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e13ed0ac06 ]
sop_drop_qpn field in the cqe is used by two features, in SWITCHDEV mode
to restore the chain id in case of a miss and in LEGACY mode to support
skbedit mark action. In build RX skb, the skb mark field is set regardless
of the configured mode which cause a corruption of the mark field in case
of switchdev mode.
Fix by overriding the mark value back to 0 in the representor tc update
skb flow.
Fixes: 8f1e0b97cc ("net/mlx5: E-Switch, Mark miss packets with new chain id mapping")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b1c0aca3d3 ]
Prior to this patch, configuring speed to 50G with autoneg off over
devices supporting 50G per lane failed.
Support for 50G per lane introduced a new set of link-modes, on which
driver always performed a speed validation as if only legacy link-modes
were configured. Fix driver speed validation to force setting autoneg
over 56G only if in legacy link-mode.
Fixes: 3d7cadae51 ("net/mlx5e: ethtool, Fix analysis of speed setting")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Eran Ben Elisha <eranbe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f9c4845385 ]
ip_finish_output_gso() may call .ndo_features_check() even before the
skb has a L2 header. This conflicts with qeth_get_ip_version()'s attempt
to inspect the L2 header via vlan_eth_hdr().
Switch to vlan_get_protocol(), as already used further down in the
common qeth_features_check() path.
Fixes: f13ade1993 ("s390/qeth: run non-offload L3 traffic over common xmit path")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b41b554c1e ]
Due to insufficient locking, qeth_core_set_online() and
qeth_dev_layer2_store() can run in parallel, both attempting to load &
setup the discipline (and stepping on each other toes along the way).
A similar race can also occur between qeth_core_remove_device() and
qeth_dev_layer2_store().
Access to .discipline is meant to be protected by the discipline_mutex,
so add/expand the locking in qeth_core_remove_device() and
qeth_core_set_online().
Adjust the locking in qeth_l*_remove_device() accordingly, as it's now
handled by the callers in a consistent manner.
Based on an initial patch by Ursula Braun.
Fixes: 9dc48ccc68 ("qeth: serialize sysfs-triggered device configurations")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0b9902c1fc ]
When qeth_dev_layer2_store() - holding the discipline_mutex - waits
inside qeth_l*_remove_device() for a qeth_do_reset() thread to complete,
we can hit a deadlock if qeth_do_reset() concurrently calls
qeth_set_online() and thus tries to aquire the discipline_mutex.
Move the discipline_mutex locking outside of qeth_set_online() and
qeth_set_offline(), and turn the discipline into a parameter so that
callers understand the dependency.
To fix the deadlock, we can now relax the locking:
As already established, qeth_l*_remove_device() waits for
qeth_do_reset() to complete. So qeth_do_reset() itself is under no risk
of having card->discipline ripped out while it's running, and thus
doesn't need to take the discipline_mutex.
Fixes: 9dc48ccc68 ("qeth: serialize sysfs-triggered device configurations")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b19218b27f ]
The function nh_check_attr_group() is called to validate nexthop groups.
The intention of that code seems to have been to bounce all attributes
above NHA_GROUP_TYPE except for NHA_FDB. However instead it bounces all
these attributes except when NHA_FDB attribute is present--then it accepts
them.
NHA_FDB validation that takes place before, in rtm_to_nh_config(), already
bounces NHA_OIF, NHA_BLACKHOLE, NHA_ENCAP and NHA_ENCAP_TYPE. Yet further
back, NHA_GROUPS and NHA_MASTER are bounced unconditionally.
But that still leaves NHA_GATEWAY as an attribute that would be accepted in
FDB nexthop groups (with no meaning), so long as it keeps the address
family as unspecified:
# ip nexthop add id 1 fdb via 127.0.0.1
# ip nexthop add id 10 fdb via default group 1
The nexthop code is still relatively new and likely not used very broadly,
and the FDB bits are newer still. Even though there is a reproducer out
there, it relies on an improbable gateway arguments "via default", "via
all" or "via any". Given all this, I believe it is OK to reformulate the
condition to do the right thing and bounce NHA_GATEWAY.
Fixes: 38428d6871 ("nexthop: support for fdb ecmp nexthops")
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 15ef6b0e30 ]
CPL_ABORT_RPL is sent after releasing the resources by calling
chtls_release_resources(sk); and chtls_conn_done(sk);
eventually causing kernel panic. Fixing it by calling release
in appropriate order.
Fixes: cc35c88ae4 ("crypto : chtls - CPL handler definition")
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Signed-off-by: Ayush Sawal <ayush.sawal@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit eade1e0a4f ]
In case of server removal lookup_stid() may return NULL pointer, which
is used as listen_ctx. So added a check before accessing this pointer.
Fixes: cc35c88ae4 ("crypto : chtls - CPL handler definition")
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Signed-off-by: Ayush Sawal <ayush.sawal@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a84b2c0d5f ]
The skb is unlinked twice, one in __skb_dequeue in function
chtls_reset_synq() and another in cleanup_syn_rcv_conn().
So in this patch using skb_peek() instead of __skb_dequeue(),
so that unlink will be handled only in cleanup_syn_rcv_conn().
Fixes: cc35c88ae4 ("crypto : chtls - CPL handler definition")
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Signed-off-by: Ayush Sawal <ayush.sawal@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5a5fac9966 ]
If route to peer is not configured, we might get non tls
devices from dst_neigh_lookup() which is invalid, adding a
check to avoid it.
Fixes: cc35c88ae4 ("crypto : chtls - CPL handler definition")
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: Ayush Sawal <ayush.sawal@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 827d329105 ]
At the time of SYN_RECV, connection information is not
initialized at FW, updating tcb flag over uninitialized
connection causes adapter crash. We don't need to
update the flag during SYN_RECV state, so avoid this.
Fixes: cc35c88ae4 ("crypto : chtls - CPL handler definition")
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: Ayush Sawal <ayush.sawal@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 717df0f4cd ]
send_abort_rpl() is not calculating cpl_abort_req_rss offset and
ends up sending wrong TID with abort_rpl WR causng tid leaks.
Replaced send_abort_rpl() with chtls_send_abort_rpl() as it is
redundant.
Fixes: cc35c88ae4 ("crypto : chtls - CPL handler definition")
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: Ayush Sawal <ayush.sawal@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bb4cc1a188 ]
Conntrack reassembly records the largest fragment size seen in IPCB.
However, when this gets forwarded/transmitted, fragmentation will only
be forced if one of the fragmented packets had the DF bit set.
In that case, a flag in IPCB will force fragmentation even if the
MTU is large enough.
This should work fine, but this breaks with ip tunnels.
Consider client that sends a UDP datagram of size X to another host.
The client fragments the datagram, so two packets, of size y and z, are
sent. DF bit is not set on any of these packets.
Middlebox netfilter reassembles those packets back to single size-X
packet, before routing decision.
packet-size-vs-mtu checks in ip_forward are irrelevant, because DF bit
isn't set. At output time, ip refragmentation is skipped as well
because x is still smaller than the mtu of the output device.
If ttransmit device is an ip tunnel, the packet size increases to
x+overhead.
Also, tunnel might be configured to force DF bit on outer header.
In this case, packet will be dropped (exceeds MTU) and an ICMP error is
generated back to sender.
But sender already respects the announced MTU, all the packets that
it sent did fit the announced mtu.
Force refragmentation as per original sizes unconditionally so ip tunnel
will encapsulate the fragments instead.
The only other solution I see is to place ip refragmentation in
the ip_tunnel code to handle this case.
Fixes: d6b915e29f ("ip_fragment: don't forward defragmented DF packet")
Reported-by: Christian Perle <christian.perle@secunet.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 50c661670f ]
For some reason ip_tunnel insist on setting the DF bit anyway when the
inner header has the DF bit set, EVEN if the tunnel was configured with
'nopmtudisc'.
This means that the script added in the previous commit
cannot be made to work by adding the 'nopmtudisc' flag to the
ip tunnel configuration. Doing so breaks connectivity even for the
without-conntrack/netfilter scenario.
When nopmtudisc is set, the tunnel will skip the mtu check, so no
icmp error is sent to client. Then, because inner header has DF set,
the outer header gets added with DF bit set as well.
IP stack then sends an error to itself because the packet exceeds
the device MTU.
Fixes: 23a3647bc4 ("ip_tunnels: Use skb-len to PMTU check.")
Cc: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5316a7c013 ]
Adds new 2 new tests to the PTMU script: pmtu_ipv4/6_route_change.
These tests explicitly test for a recently discovered problem in the
IPv6 routing framework where PMTU exceptions were not properly released
when replacing a route via "ip route change ...".
After creating PMTU exceptions, the route from the device A to R1 will be
replaced with a new route, then device A will be deleted. If the PMTU
exceptions were properly cleaned up by the kernel, this device deletion
will succeed. Otherwise, the unregistration of the device will stall, and
messages such as the following will be logged in dmesg:
unregister_netdevice: waiting for veth_A-R1 to become free. Usage count = 4
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/1609892546-11389-2-git-send-email-stranche@quicinc.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d8f5c29653 ]
Route removal is handled by two code paths. The main removal path is via
fib6_del_route() which will handle purging any PMTU exceptions from the
cache, removing all per-cpu copies of the DST entry used by the route, and
releasing the fib6_info struct.
The second removal location is during fib6_add_rt2node() during a route
replacement operation. This path also calls fib6_purge_rt() to handle
cleaning up the per-cpu copies of the DST entries and releasing the
fib6_info associated with the older route, but it does not flush any PMTU
exceptions that the older route had. Since the older route is removed from
the tree during the replacement, we lose any way of accessing it again.
As these lingering DSTs and the fib6_info struct are holding references to
the underlying netdevice struct as well, unregistering that device from the
kernel can never complete.
Fixes: 2b760fcf5c ("ipv6: hook up exception table to store dst cache")
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/1609892546-11389-1-git-send-email-stranche@quicinc.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 94bcfdbff0 ]
.dellink does not get called after .newlink fails,
bareudp_newlink() must undo what bareudp_configure()
has done if bareudp_link_config() fails.
v2: call bareudp_dellink(), like bareudp_dev_create() does
Fixes: 571912c69f ("net: UDP tunnel encapsulation module for tunnelling different protocols like MPLS, IP, NSH etc.")
Link: https://lore.kernel.org/r/20210105190725.1736246-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0f7ba7bc46 ]
A call to dma_alloc_coherent() is wrapped by sonic_alloc_descriptors().
This is correctly freed in the remove function, but not in the error
handling path of the probe function. Fix this by adding the missing
dma_free_coherent() call.
While at it, rename a label in order to be slightly more informative.
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Chris Zankel <chris@zankel.net>
References: commit 10e3cc180e ("net/sonic: Fix a resource leak in an error handling path in 'jazz_sonic_probe()'")
Fixes: 74f2a5f0ef ("xtensa: Add support for the Sonic Ethernet device for the XT2000 board.")
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 55b7ab1178 ]
VLAN checks for NETREG_UNINITIALIZED to distinguish between
registration failure and unregistration in progress.
Since commit cb626bf566 ("net-sysfs: Fix reference count leak")
registration failure may, however, result in NETREG_UNREGISTERED
as well as NETREG_UNINITIALIZED.
This fix is similer to cebb69754f ("rtnetlink: Fix
memory(net_device) leak when ->newlink fails")
Fixes: cb626bf566 ("net-sysfs: Fix reference count leak")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9b1e39cf5d ]
Previously, sun8i_dwmac_set_syscon was called from a chain of functions
in several different files:
sun8i_dwmac_probe
stmmac_dvr_probe
stmmac_hw_init
stmmac_hwif_init
sun8i_dwmac_setup
sun8i_dwmac_set_syscon
which made the lifetime of the syscon values hard to reason about. Part
of the problem is that there is no similar platform driver callback from
stmmac_dvr_remove. As a result, the driver unset the syscon value in
sun8i_dwmac_exit, but this leaves it uninitialized after a suspend/
resume cycle. It was also unset a second time (outside sun8i_dwmac_exit)
in the probe error path.
Move the init to the earliest available place in sun8i_dwmac_probe
(after stmmac_probe_config_dt, which initializes plat_dat), and the
deinit to the corresponding position in the cleanup order.
Since priv is not filled in until stmmac_dvr_probe, this requires
changing the sun8i_dwmac_set_syscon parameters to priv's two relevant
members.
Fixes: 9f93ac8d40 ("net-next: stmmac: Add dwmac-sun8i")
Fixes: 634db83b82 ("net: stmmac: dwmac-sun8i: Handle integrated/external MDIOs")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b823963885 ]
sun8i_dwmac_exit calls sun8i_dwmac_unpower_internal_phy, but
sun8i_dwmac_init did not call sun8i_dwmac_power_internal_phy. This
caused PHY power to remain off after a suspend/resume cycle. Fix this by
recording if PHY power should be restored, and if so, restoring it.
Fixes: 634db83b82 ("net: stmmac: dwmac-sun8i: Handle integrated/external MDIOs")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5292542167 ]
While stmmac_pltfr_remove calls sun8i_dwmac_exit, the sun8i_dwmac_init
and sun8i_dwmac_exit functions are also called by the stmmac_platform
suspend/resume callbacks. They may be called many times during the
device's lifetime and should not release resources used by the driver.
Furthermore, there was no error handling in case registering the MDIO
mux failed during probe, and the EPHY clock was never released at all.
Fix all of these issues by moving the deinitialization code to a driver
removal callback. Also ensure the EPHY is powered down before removal.
Fixes: 634db83b82 ("net: stmmac: dwmac-sun8i: Handle integrated/external MDIOs")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7eeecc4b1f ]
stmmac_pltfr_remove does three things in one function, making it
inapproprate for unwinding the steps in the probe function. Currently,
a failure before the call to stmmac_dvr_probe would leak OF node
references due to missing a call to stmmac_remove_config_dt. And an
error in stmmac_dvr_probe would cause the driver to attempt to remove a
netdevice that was never added. Fix these by reordering the init and
splitting out the error handling steps.
Fixes: 9f93ac8d40 ("net-next: stmmac: Add dwmac-sun8i")
Fixes: 40a1dcee2d ("net: ethernet: dwmac-sun8i: Use the correct function in exit path")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f04bbcbf1e ]
When phy driver does not implement the set_loopback interface,
phy loopback test will return -EOPNOTSUPP, and the loopback test
will fail. So when phy driver does not implement the set_loopback
interface, don't do phy loopback test.
Fixes: c9765a89d1 ("net: hns3: add phy selftest function")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 65e61e3c2a ]
HCLGE_MBX_MAX_ARQ_MSG_NUM is used to apply memory for the number
of queues used by ARQ(Asynchronous Receive Queue), so the head
and tail pointers should also use this macro.
Fixes: 07a0556a3a ("net: hns3: Changes to support ARQ(Asynchronous Receive Queue)")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ab6e32d291 ]
For DEVICE_VERSION_V2, the hardware only supports src-ip,
dst-ip and verification-tag for rss tuple set of sctp6
packet. For DEVICE_VERSION_V3, the hardware supports
src-port and dst-port as well.
Currently, when user queries the sctp6 rss tuples info,
some unsupported information will be showed on V2. So add
a check for hardware version when initializing and queries
sctp6 rss tuple to fix this issue.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7a68d725e4 ]
Aligning to tx_ndp_modulus is not sufficient because the next align
call can be cdc_ncm_align_tail, which can add up to ctx->tx_modulus +
ctx->tx_remainder - 1 bytes. This used to lead to occasional crashes
on a Huawei 909s-120 LTE module as follows:
- the condition marked /* if there is a remaining skb [...] */ is true
so the swaps happen
- skb_out is set from ctx->tx_curr_skb
- skb_out->len is exactly 0x3f52
- ctx->tx_curr_size is 0x4000 and delayed_ndp_size is 0xac
(note that the sum of skb_out->len and delayed_ndp_size is 0x3ffe)
- the for loop over n is executed once
- the cdc_ncm_align_tail call marked /* align beginning of next frame */
increases skb_out->len to 0x3f56 (the sum is now 0x4002)
- the condition marked /* check if we had enough room left [...] */ is
false so we break out of the loop
- the condition marked /* If requested, put NDP at end of frame. */ is
true so the NDP is written into skb_out
- now skb_out->len is 0x4002, so padding_count is minus two interpreted
as an unsigned number, which is used as the length argument to memset,
leading to a crash with various symptoms but usually including
> Call Trace:
> <IRQ>
> cdc_ncm_fill_tx_frame+0x83a/0x970 [cdc_ncm]
> cdc_mbim_tx_fixup+0x1d9/0x240 [cdc_mbim]
> usbnet_start_xmit+0x5d/0x720 [usbnet]
The cdc_ncm_align_tail call first aligns on a ctx->tx_modulus
boundary (adding at most ctx->tx_modulus-1 bytes), then adds
ctx->tx_remainder bytes. Alternatively, the next alignment call can
occur in cdc_ncm_ndp16 or cdc_ncm_ndp32, in which case at most
ctx->tx_ndp_modulus-1 bytes are added.
A similar problem has occurred before, and the code is nontrivial to
reason about, so add a guard before the crashing call. By that time it
is too late to prevent any memory corruption (we'll have written past
the end of the buffer already) but we can at least try to get a warning
written into an on-disk log by avoiding the hard crash caused by padding
past the buffer with a huge number of zeros.
Signed-off-by: Jouni K. Seppänen <jks@iki.fi>
Fixes: 4a0e3e989d ("cdc_ncm: Add support for moving NDP to end of NCM frame")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209407
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e076ab2a2c ]
Commit 38d715f494 ("btrfs: use btrfs_start_delalloc_roots in
shrink_delalloc") cleaned up how we do delalloc shrinking by utilizing
some infrastructure we have in place to flush inodes that we use for
device replace and snapshot. However this introduced a pretty serious
performance regression. To reproduce the user untarred the source
tarball of Firefox (360MiB xz compressed/1.5GiB uncompressed), and would
see it take anywhere from 5 to 20 times as long to untar in 5.10
compared to 5.9. This was observed on fast devices (SSD and better) and
not on HDD.
The root cause is because before we would generally use the normal
writeback path to reclaim delalloc space, and for this we would provide
it with the number of pages we wanted to flush. The referenced commit
changed this to flush that many inodes, which drastically increased the
amount of space we were flushing in certain cases, which severely
affected performance.
We cannot revert this patch unfortunately because of 3d45f221ce
("btrfs: fix deadlock when cloning inline extent and low on free
metadata space") which requires the ability to skip flushing inodes that
are being cloned in certain scenarios, which means we need to keep using
our flushing infrastructure or risk re-introducing the deadlock.
Instead to fix this problem we can go back to providing
btrfs_start_delalloc_roots with a number of pages to flush, and then set
up a writeback_control and utilize sync_inode() to handle the flushing
for us. This gives us the same behavior we had prior to the fix, while
still allowing us to avoid the deadlock that was fixed by Filipe. I
redid the users original test and got the following results on one of
our test machines (256GiB of ram, 56 cores, 2TiB Intel NVMe drive)
5.9 0m54.258s
5.10 1m26.212s
5.10+patch 0m38.800s
5.10+patch is significantly faster than plain 5.9 because of my patch
series "Change data reservations to use the ticketing infra" which
contained the patch that introduced the regression, but generally
improved the overall ENOSPC flushing mechanisms.
Additional testing on consumer-grade SSD (8GiB ram, 8 CPU) confirm
the results:
5.10.5 4m00s
5.10.5+patch 1m08s
5.11-rc2 5m14s
5.11-rc2+patch 1m30s
Reported-by: René Rebe <rene@exactcode.de>
Fixes: 38d715f494 ("btrfs: use btrfs_start_delalloc_roots in shrink_delalloc")
CC: stable@vger.kernel.org # 5.10
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Tested-by: David Sterba <dsterba@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ add my test results ]
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d45f221ce ]
When cloning an inline extent there are cases where we can not just copy
the inline extent from the source range to the target range (e.g. when the
target range starts at an offset greater than zero). In such cases we copy
the inline extent's data into a page of the destination inode and then
dirty that page. However, after that we will need to start a transaction
for each processed extent and, if we are ever low on available metadata
space, we may need to flush existing delalloc for all dirty inodes in an
attempt to release metadata space - if that happens we may deadlock:
* the async reclaim task queued a delalloc work to flush delalloc for
the destination inode of the clone operation;
* the task executing that delalloc work gets blocked waiting for the
range with the dirty page to be unlocked, which is currently locked
by the task doing the clone operation;
* the async reclaim task blocks waiting for the delalloc work to complete;
* the cloning task is waiting on the waitqueue of its reservation ticket
while holding the range with the dirty page locked in the inode's
io_tree;
* if metadata space is not released by some other task (like delalloc for
some other inode completing for example), the clone task waits forever
and as a consequence the delalloc work and async reclaim tasks will hang
forever as well. Releasing more space on the other hand may require
starting a transaction, which will hang as well when trying to reserve
metadata space, resulting in a deadlock between all these tasks.
When this happens, traces like the following show up in dmesg/syslog:
[87452.323003] INFO: task kworker/u16:11:1810830 blocked for more than 120 seconds.
[87452.323644] Tainted: G B W 5.10.0-rc4-btrfs-next-73 #1
[87452.324248] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[87452.324852] task:kworker/u16:11 state:D stack: 0 pid:1810830 ppid: 2 flags:0x00004000
[87452.325520] Workqueue: btrfs-flush_delalloc btrfs_work_helper [btrfs]
[87452.326136] Call Trace:
[87452.326737] __schedule+0x5d1/0xcf0
[87452.327390] schedule+0x45/0xe0
[87452.328174] lock_extent_bits+0x1e6/0x2d0 [btrfs]
[87452.328894] ? finish_wait+0x90/0x90
[87452.329474] btrfs_invalidatepage+0x32c/0x390 [btrfs]
[87452.330133] ? __mod_memcg_state+0x8e/0x160
[87452.330738] __extent_writepage+0x2d4/0x400 [btrfs]
[87452.331405] extent_write_cache_pages+0x2b2/0x500 [btrfs]
[87452.332007] ? lock_release+0x20e/0x4c0
[87452.332557] ? trace_hardirqs_on+0x1b/0xf0
[87452.333127] extent_writepages+0x43/0x90 [btrfs]
[87452.333653] ? lock_acquire+0x1a3/0x490
[87452.334177] do_writepages+0x43/0xe0
[87452.334699] ? __filemap_fdatawrite_range+0xa4/0x100
[87452.335720] __filemap_fdatawrite_range+0xc5/0x100
[87452.336500] btrfs_run_delalloc_work+0x17/0x40 [btrfs]
[87452.337216] btrfs_work_helper+0xf1/0x600 [btrfs]
[87452.337838] process_one_work+0x24e/0x5e0
[87452.338437] worker_thread+0x50/0x3b0
[87452.339137] ? process_one_work+0x5e0/0x5e0
[87452.339884] kthread+0x153/0x170
[87452.340507] ? kthread_mod_delayed_work+0xc0/0xc0
[87452.341153] ret_from_fork+0x22/0x30
[87452.341806] INFO: task kworker/u16:1:2426217 blocked for more than 120 seconds.
[87452.342487] Tainted: G B W 5.10.0-rc4-btrfs-next-73 #1
[87452.343274] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[87452.344049] task:kworker/u16:1 state:D stack: 0 pid:2426217 ppid: 2 flags:0x00004000
[87452.344974] Workqueue: events_unbound btrfs_async_reclaim_metadata_space [btrfs]
[87452.345655] Call Trace:
[87452.346305] __schedule+0x5d1/0xcf0
[87452.346947] ? kvm_clock_read+0x14/0x30
[87452.347676] ? wait_for_completion+0x81/0x110
[87452.348389] schedule+0x45/0xe0
[87452.349077] schedule_timeout+0x30c/0x580
[87452.349718] ? _raw_spin_unlock_irqrestore+0x3c/0x60
[87452.350340] ? lock_acquire+0x1a3/0x490
[87452.351006] ? try_to_wake_up+0x7a/0xa20
[87452.351541] ? lock_release+0x20e/0x4c0
[87452.352040] ? lock_acquired+0x199/0x490
[87452.352517] ? wait_for_completion+0x81/0x110
[87452.353000] wait_for_completion+0xab/0x110
[87452.353490] start_delalloc_inodes+0x2af/0x390 [btrfs]
[87452.353973] btrfs_start_delalloc_roots+0x12d/0x250 [btrfs]
[87452.354455] flush_space+0x24f/0x660 [btrfs]
[87452.355063] btrfs_async_reclaim_metadata_space+0x1bb/0x480 [btrfs]
[87452.355565] process_one_work+0x24e/0x5e0
[87452.356024] worker_thread+0x20f/0x3b0
[87452.356487] ? process_one_work+0x5e0/0x5e0
[87452.356973] kthread+0x153/0x170
[87452.357434] ? kthread_mod_delayed_work+0xc0/0xc0
[87452.357880] ret_from_fork+0x22/0x30
(...)
< stack traces of several tasks waiting for the locks of the inodes of the
clone operation >
(...)
[92867.444138] RSP: 002b:00007ffc3371bbe8 EFLAGS: 00000246 ORIG_RAX: 0000000000000052
[92867.444624] RAX: ffffffffffffffda RBX: 00007ffc3371bea0 RCX: 00007f61efe73f97
[92867.445116] RDX: 0000000000000000 RSI: 0000560fbd5d7a40 RDI: 0000560fbd5d8960
[92867.445595] RBP: 00007ffc3371beb0 R08: 0000000000000001 R09: 0000000000000003
[92867.446070] R10: 00007ffc3371b996 R11: 0000000000000246 R12: 0000000000000000
[92867.446820] R13: 000000000000001f R14: 00007ffc3371bea0 R15: 00007ffc3371beb0
[92867.447361] task:fsstress state:D stack: 0 pid:2508238 ppid:2508153 flags:0x00004000
[92867.447920] Call Trace:
[92867.448435] __schedule+0x5d1/0xcf0
[92867.448934] ? _raw_spin_unlock_irqrestore+0x3c/0x60
[92867.449423] schedule+0x45/0xe0
[92867.449916] __reserve_bytes+0x4a4/0xb10 [btrfs]
[92867.450576] ? finish_wait+0x90/0x90
[92867.451202] btrfs_reserve_metadata_bytes+0x29/0x190 [btrfs]
[92867.451815] btrfs_block_rsv_add+0x1f/0x50 [btrfs]
[92867.452412] start_transaction+0x2d1/0x760 [btrfs]
[92867.453216] clone_copy_inline_extent+0x333/0x490 [btrfs]
[92867.453848] ? lock_release+0x20e/0x4c0
[92867.454539] ? btrfs_search_slot+0x9a7/0xc30 [btrfs]
[92867.455218] btrfs_clone+0x569/0x7e0 [btrfs]
[92867.455952] btrfs_clone_files+0xf6/0x150 [btrfs]
[92867.456588] btrfs_remap_file_range+0x324/0x3d0 [btrfs]
[92867.457213] do_clone_file_range+0xd4/0x1f0
[92867.457828] vfs_clone_file_range+0x4d/0x230
[92867.458355] ? lock_release+0x20e/0x4c0
[92867.458890] ioctl_file_clone+0x8f/0xc0
[92867.459377] do_vfs_ioctl+0x342/0x750
[92867.459913] __x64_sys_ioctl+0x62/0xb0
[92867.460377] do_syscall_64+0x33/0x80
[92867.460842] entry_SYSCALL_64_after_hwframe+0x44/0xa9
(...)
< stack traces of more tasks blocked on metadata reservation like the clone
task above, because the async reclaim task has deadlocked >
(...)
Another thing to notice is that the worker task that is deadlocked when
trying to flush the destination inode of the clone operation is at
btrfs_invalidatepage(). This is simply because the clone operation has a
destination offset greater than the i_size and we only update the i_size
of the destination file after cloning an extent (just like we do in the
buffered write path).
Since the async reclaim path uses btrfs_start_delalloc_roots() to trigger
the flushing of delalloc for all inodes that have delalloc, add a runtime
flag to an inode to signal it should not be flushed, and for inodes with
that flag set, start_delalloc_inodes() will simply skip them. When the
cloning code needs to dirty a page to copy an inline extent, set that flag
on the inode and then clear it when the clone operation finishes.
This could be sporadically triggered with test case generic/269 from
fstests, which exercises many fsstress processes running in parallel with
several dd processes filling up the entire filesystem.
CC: stable@vger.kernel.org # 5.9+
Fixes: 05a5a7621c ("Btrfs: implement full reflink support for inline extents")
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2f121ab50 ]
Every time we log an inode we lookup in the fs/subvol tree for xattrs and
if we have any, log them into the log tree. However it is very common to
have inodes without any xattrs, so doing the search wastes times, but more
importantly it adds contention on the fs/subvol tree locks, either making
the logging code block and wait for tree locks or making the logging code
making other concurrent operations block and wait.
The most typical use cases where xattrs are used are when capabilities or
ACLs are defined for an inode, or when SELinux is enabled.
This change makes the logging code detect when an inode does not have
xattrs and skip the xattrs search the next time the inode is logged,
unless the inode is evicted and loaded again or a xattr is added to the
inode. Therefore skipping the search for xattrs on inodes that don't ever
have xattrs and are fsynced with some frequency.
The following script that calls dbench was used to measure the impact of
this change on a VM with 8 CPUs, 16Gb of ram, using a raw NVMe device
directly (no intermediary filesystem on the host) and using a non-debug
kernel (default configuration on Debian distributions):
$ cat test.sh
#!/bin/bash
DEV=/dev/sdk
MNT=/mnt/sdk
MOUNT_OPTIONS="-o ssd"
mkfs.btrfs -f -m single -d single $DEV
mount $MOUNT_OPTIONS $DEV $MNT
dbench -D $MNT -t 200 40
umount $MNT
The results before this change:
Operation Count AvgLat MaxLat
----------------------------------------
NTCreateX 5761605 0.172 312.057
Close 4232452 0.002 10.927
Rename 243937 1.406 277.344
Unlink 1163456 0.631 298.402
Deltree 160 11.581 221.107
Mkdir 80 0.003 0.005
Qpathinfo 5221410 0.065 122.309
Qfileinfo 915432 0.001 3.333
Qfsinfo 957555 0.003 3.992
Sfileinfo 469244 0.023 20.494
Find 2018865 0.448 123.659
WriteX 2874851 0.049 118.529
ReadX 9030579 0.004 21.654
LockX 18754 0.003 4.423
UnlockX 18754 0.002 0.331
Flush 403792 10.944 359.494
Throughput 908.444 MB/sec 40 clients 40 procs max_latency=359.500 ms
The results after this change:
Operation Count AvgLat MaxLat
----------------------------------------
NTCreateX 6442521 0.159 230.693
Close 4732357 0.002 10.972
Rename 272809 1.293 227.398
Unlink 1301059 0.563 218.500
Deltree 160 7.796 54.887
Mkdir 80 0.008 0.478
Qpathinfo 5839452 0.047 124.330
Qfileinfo 1023199 0.001 4.996
Qfsinfo 1070760 0.003 5.709
Sfileinfo 524790 0.033 21.765
Find 2257658 0.314 125.611
WriteX 3211520 0.040 232.135
ReadX 10098969 0.004 25.340
LockX 20974 0.003 1.569
UnlockX 20974 0.002 3.475
Flush 451553 10.287 331.037
Throughput 1011.77 MB/sec 40 clients 40 procs max_latency=331.045 ms
+10.8% throughput, -8.2% max latency
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4c60244dc3 ]
clang complains about a possible code path in which a variable is used
without an initialization:
drivers/scsi/ufs/ufshcd.c:7690:3: error: variable 'sdp' is used uninitialized whenever 'if' condition is false [-Werror,-Wsometimes-uninitialized]
BUG_ON(1);
^~~~~~~~~
include/asm-generic/bug.h:63:36: note: expanded from macro 'BUG_ON'
#define BUG_ON(condition) do { if (unlikely(condition)) BUG(); } while (0)
^~~~~~~~~~~~~~~~~~~
Turn the BUG_ON(1) into an unconditional BUG() that makes it clear to clang
that this code path is never hit.
Link: https://lore.kernel.org/r/20201203223137.1205933-1-arnd@kernel.org
Fixes: 4f3e900b62 ("scsi: ufs: Clear UAC for FFU and RPMB LUNs")
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3e2224c586 ]
alloc_fixed_file_ref_node() currently returns an ERR_PTR on failure.
io_sqe_files_unregister() expects it to return NULL and since it can only
return -ENOMEM, it makes more sense to change alloc_fixed_file_ref_node()
to behave that way.
Fixes: 1ffc54220c ("io_uring: fix io_sqe_files_unregister() hangs")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aded8c7c2b ]
On SM8150 it's occasionally observed that the boot hangs in between the
writing of SMEs and context banks in arm_smmu_device_reset().
The problem seems to coincide with a display refresh happening after
updating the stream mapping, but before clearing - and there by
disabling translation - the context bank picked to emulate translation
bypass.
Resolve this by explicitly disabling the bypass context already in
cfg_probe.
Fixes: f9081b8ff5 ("iommu/arm-smmu-qcom: Implement S2CR quirk")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210106005038.4152731-1-bjorn.andersson@linaro.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6c503150ae upstream
IOPOLL skips completion locking but keeps it under uring_lock, thus
io_cqring_overflow_flush() and so io_cqring_events() need additional
locking with uring_lock in some cases for IOPOLL.
Remove __io_cqring_overflow_flush() from io_cqring_events(), introduce a
wrapper around flush doing needed synchronisation and call it by hand.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 89448c47b8 upstream
We don't need to take uring_lock for SQPOLL|IOPOLL to do
io_cqring_overflow_flush() when cq_overflow_list is empty, remove it
from the hot path.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 81b6d05cca upstream
io_req_task_submit() might be called for IOPOLL, do the fail path under
uring_lock to comply with IOPOLL synchronisation based solely on it.
Cc: stable@vger.kernel.org # 5.5+
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2896c93811 upstream.
When attempting to match EXTENDED COPY CSCD descriptors with corresponding
se_devices, target_xcopy_locate_se_dev_e4() currently iterates over LIO's
global devices list which includes all configured backstores.
This change ensures that only initiator-accessible backstores are
considered during CSCD descriptor lookup, according to the session's
se_node_acl LUN list.
To avoid LUN removal race conditions, device pinning is changed from being
configfs based to instead using the se_node_acl lun_ref.
Reference: CVE-2020-28374
Fixes: cbf031f425 ("target: Add support for EXTENDED_COPY copy offload emulation")
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8bee683384 upstream.
Fix a possible memory leak when a bind of an AF_XDP socket fails. When
the fill and completion rings are created, they are tied to the
socket. But when the buffer pool is later created at bind time, the
ownership of these two rings are transferred to the buffer pool as
they might be shared between sockets (and the buffer pool cannot be
created until we know what we are binding to). So, before the buffer
pool is created, these two rings are cleaned up with the socket, and
after they have been transferred they are cleaned up together with
the buffer pool.
The problem is that ownership was transferred before it was absolutely
certain that the buffer pool could be created and initialized
correctly and when one of these errors occurred, the fill and
completion rings did neither belong to the socket nor the pool and
where therefore leaked. Solve this by moving the ownership transfer
to the point where the buffer pool has been completely set up and
there is no way it can fail.
Fixes: 7361f9c3d7 ("xsk: Move fill and completion rings to buffer pool")
Reported-by: syzbot+cfa88ddd0655afa88763@syzkaller.appspotmail.com
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/bpf/20201214085127.3960-1-magnus.karlsson@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cb7f4a8b1f upstream.
In mtrr_type_lookup(), if the input memory address region is not in the
MTRR, over 4GB, and not over the top of memory, a write-back attribute
is returned. These condition checks are for ensuring the input memory
address region is actually mapped to the physical memory.
However, if the end address is just aligned with the top of memory,
the condition check treats the address is over the top of memory, and
write-back attribute is not returned.
And this hits in a real use case with NVDIMM: the nd_pmem module tries
to map NVDIMMs as cacheable memories when NVDIMMs are connected. If a
NVDIMM is the last of the DIMMs, the performance of this NVDIMM becomes
very low since it is aligned with the top of memory and its memory type
is uncached-minus.
Move the input end address change to inclusive up into
mtrr_type_lookup(), before checking for the top of memory in either
mtrr_type_lookup_{variable,fixed}() helpers.
[ bp: Massage commit message. ]
Fixes: 0cc705f56e ("x86/mm/mtrr: Clean up mtrr_type_lookup()")
Signed-off-by: Ying-Tsun Huang <ying-tsun.huang@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20201215070721.4349-1-ying-tsun.huang@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 95cd4bca7b upstream.
If userspace requests a feature which is not available the original set
definition, then bail out with EOPNOTSUPP. If userspace sends
unsupported dynset flags (new feature not supported by this kernel),
then report EOPNOTSUPP to userspace. EINVAL should be only used to
report malformed netlink messages from userspace.
Fixes: 22fe54d5fe ("netfilter: nf_tables: add support for dynamic set updates")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c8193f568 upstream.
htable_bits() can call jhash_size(32) and trigger shift-out-of-bounds
UBSAN: shift-out-of-bounds in net/netfilter/ipset/ip_set_hash_gen.h:151:6
shift exponent 32 is too large for 32-bit type 'unsigned int'
CPU: 0 PID: 8498 Comm: syz-executor519
Not tainted 5.10.0-rc7-next-20201208-syzkaller #0
Call Trace:
__dump_stack lib/dump_stack.c:79 [inline]
dump_stack+0x107/0x163 lib/dump_stack.c:120
ubsan_epilogue+0xb/0x5a lib/ubsan.c:148
__ubsan_handle_shift_out_of_bounds.cold+0xb1/0x181 lib/ubsan.c:395
htable_bits net/netfilter/ipset/ip_set_hash_gen.h:151 [inline]
hash_mac_create.cold+0x58/0x9b net/netfilter/ipset/ip_set_hash_gen.h:1524
ip_set_create+0x610/0x1380 net/netfilter/ipset/ip_set_core.c:1115
nfnetlink_rcv_msg+0xecc/0x1180 net/netfilter/nfnetlink.c:252
netlink_rcv_skb+0x153/0x420 net/netlink/af_netlink.c:2494
nfnetlink_rcv+0x1ac/0x420 net/netfilter/nfnetlink.c:600
netlink_unicast_kernel net/netlink/af_netlink.c:1304 [inline]
netlink_unicast+0x533/0x7d0 net/netlink/af_netlink.c:1330
netlink_sendmsg+0x907/0xe40 net/netlink/af_netlink.c:1919
sock_sendmsg_nosec net/socket.c:652 [inline]
sock_sendmsg+0xcf/0x120 net/socket.c:672
____sys_sendmsg+0x6e8/0x810 net/socket.c:2345
___sys_sendmsg+0xf3/0x170 net/socket.c:2399
__sys_sendmsg+0xe5/0x1b0 net/socket.c:2432
do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x44/0xa9
This patch replaces htable_bits() by simple fls(hashsize - 1) call:
it alone returns valid nbits both for round and non-round hashsizes.
It is normal to set any nbits here because it is validated inside
following htable_size() call which returns 0 for nbits>31.
Fixes: 1feab10d7e6d("netfilter: ipset: Unified hash type generation")
Reported-by: syzbot+d66bfadebca46cf61a2b@syzkaller.appspotmail.com
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Acked-by: Jozsef Kadlecsik <kadlec@netfilter.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f1dc15cd7f upstream.
AES needs to be disabled on Nokia N950/N9 as well (HS devices), otherwise
kernel fails to boot.
Fixes: c312f06631 ("ARM: dts: omap3: Migrate AES from hwmods to sysc-omap2")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b544011f0e upstream.
In case WQE includes inline header the vlan is inserted by driver even
if vlan offload is set. On geneve over vlan interface where software
parser is used the SWP offsets should be updated according to the added
vlan.
Fixes: e3cfc7e6b7 ("net/mlx5e: TX, Add geneve tunnel stateless offload support")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b16671e8f4 upstream.
When large bucket feature was added, BCH_FEATURE_INCOMPAT_LARGE_BUCKET
was introduced into the incompat feature set. It used bucket_size_hi
(which was added at the tail of struct cache_sb_disk) to extend current
16bit bucket size to 32bit with existing bucket_size in struct
cache_sb_disk.
This is not a good idea, there are two obvious problems,
- Bucket size is always value power of 2, if store log2(bucket size) in
existing bucket_size of struct cache_sb_disk, it is unnecessary to add
bucket_size_hi.
- Macro csum_set() assumes d[SB_JOURNAL_BUCKETS] is the last member in
struct cache_sb_disk, bucket_size_hi was added after d[] which makes
csum_set calculate an unexpected super block checksum.
To fix the above problems, this patch introduces a new incompat feature
bit BCH_FEATURE_INCOMPAT_LOG_LARGE_BUCKET_SIZE, when this bit is set, it
means bucket_size in struct cache_sb_disk stores the order of power-of-2
bucket size value. When user specifies a bucket size larger than 32768
sectors, BCH_FEATURE_INCOMPAT_LOG_LARGE_BUCKET_SIZE will be set to
incompat feature set, and bucket_size stores log2(bucket size) more
than store the real bucket size value.
The obsoleted BCH_FEATURE_INCOMPAT_LARGE_BUCKET won't be used anymore,
it is renamed to BCH_FEATURE_INCOMPAT_OBSO_LARGE_BUCKET and still only
recognized by kernel driver for legacy compatible purpose. The previous
bucket_size_hi is renmaed to obso_bucket_size_hi in struct cache_sb_disk
and not used in bcache-tools anymore.
For cache device created with BCH_FEATURE_INCOMPAT_LARGE_BUCKET feature,
bcache-tools and kernel driver still recognize the feature string and
display it as "obso_large_bucket".
With this change, the unnecessary extra space extend of bcache on-disk
super block can be avoided, and csum_set() may generate expected check
sum as well.
Fixes: ffa4703275 ("bcache: add bucket_size_hi into struct cache_sb_disk for large bucket")
Signed-off-by: Coly Li <colyli@suse.de>
Cc: stable@vger.kernel.org # 5.9+
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1dfc0686c2 upstream.
This patch adds the check for features which is incompatible for
current supported feature sets.
Now if the bcache device created by bcache-tools has features that
current kernel doesn't support, read_super() will fail with error
messoage. E.g. if an unsupported incompatible feature detected,
bcache register will fail with dmesg "bcache: register_bcache() error :
Unsupported incompatible feature found".
Fixes: d721a43ff6 ("bcache: increase super block version for cache device and backing device")
Fixes: ffa4703275 ("bcache: add bucket_size_hi into struct cache_sb_disk for large bucket")
Signed-off-by: Coly Li <colyli@suse.de>
Cc: stable@vger.kernel.org # 5.9+
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f7b4943dea upstream.
This patch fixes the following typos,
from BCH_FEATURE_COMPAT_SUUP to BCH_FEATURE_COMPAT_SUPP
from BCH_FEATURE_INCOMPAT_SUUP to BCH_FEATURE_INCOMPAT_SUPP
from BCH_FEATURE_INCOMPAT_SUUP to BCH_FEATURE_RO_COMPAT_SUPP
Fixes: d721a43ff6 ("bcache: increase super block version for cache device and backing device")
Fixes: ffa4703275 ("bcache: add bucket_size_hi into struct cache_sb_disk for large bucket")
Signed-off-by: Coly Li <colyli@suse.de>
Cc: stable@vger.kernel.org # 5.9+
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 311bea3cb9 upstream.
With GNU binutils 2.35+, linking with BFD produces warnings for vmlinux:
aarch64-linux-gnu-ld: warning: -z norelro ignored
BFD can produce this warning when the target emulation mode does not
support RELRO program headers, and -z relro or -z norelro is passed.
Alan Modra clarifies:
The default linker emulation for an aarch64-linux ld.bfd is
-maarch64linux, the default for an aarch64-elf linker is
-maarch64elf. They are not equivalent. If you choose -maarch64elf
you get an emulation that doesn't support -z relro.
The ARCH=arm64 kernel prefers -maarch64elf, but may fall back to
-maarch64linux based on the toolchain configuration.
LLD will always create RELRO program header regardless of target
emulation.
To avoid the above warning when linking with BFD, pass -z norelro only
when linking with LLD or with -maarch64linux.
Fixes: 3b92fa7485 ("arm64: link with -z norelro regardless of CONFIG_RELOCATABLE")
Fixes: 3bbd3db864 ("arm64: relocatable: fix inconsistencies in linker script and options")
Cc: <stable@vger.kernel.org> # 5.0.x-
Reported-by: kernelci.org bot <bot@kernelci.org>
Reported-by: Quentin Perret <qperret@google.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Cc: Alan Modra <amodra@gmail.com>
Cc: Fāng-ruì Sòng <maskray@google.com>
Link: https://lore.kernel.org/r/20201218002432.788499-1-ndesaulniers@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05cd84691e upstream.
It is observed 'use-after-free' on the dmabuf's file->f_inode with the
race between closing the dmabuf file and reading the dmabuf's debug
info.
Consider the below scenario where P1 is closing the dma_buf file
and P2 is reading the dma_buf's debug info in the system:
P1 P2
dma_buf_debug_show()
dma_buf_put()
__fput()
file->f_op->release()
dput()
....
dentry_unlink_inode()
iput(dentry->d_inode)
(where the inode is freed)
mutex_lock(&db_list.lock)
read 'dma_buf->file->f_inode'
(the same inode is freed by P1)
mutex_unlock(&db_list.lock)
dentry->d_op->d_release()-->
dma_buf_release()
.....
mutex_lock(&db_list.lock)
removes the dmabuf from the list
mutex_unlock(&db_list.lock)
In the above scenario, when dma_buf_put() is called on a dma_buf, it
first frees the dma_buf's file->f_inode(=dentry->d_inode) and then
removes this dma_buf from the system db_list. In between P2 traversing
the db_list tries to access this dma_buf's file->f_inode that was freed
by P1 which is a use-after-free case.
Since, __fput() calls f_op->release first and then later calls the
d_op->d_release, move the dma_buf's db_list removal from d_release() to
f_op->release(). This ensures that dma_buf's file->f_inode is not
accessed after it is released.
Cc: <stable@vger.kernel.org> # 5.4.x-
Fixes: 4ab59c3c63 ("dma-buf: Move dma_buf_release() from fops to dentry_ops")
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Charan Teja Reddy <charante@codeaurora.org>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/1609857399-31549-1-git-send-email-charante@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 47f4469970 upstream.
While commit d5dcce0c41 ("device property: Keep secondary firmware
node secondary by type") describes everything correct in its commit
message, the change it made does the opposite and original commit
c15e1bdda4 ("device property: Fix the secondary firmware node handling
in set_primary_fwnode()") was fully correct.
Revert the former one here and improve documentation in the next patch.
Fixes: d5dcce0c41 ("device property: Keep secondary firmware node secondary by type")
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: 5.10+ <stable@vger.kernel.org> # 5.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0b3f407e67 upstream.
When doing an incremental send, if we have a new inode that happens to
have the same number that an old directory inode had in the base snapshot
and that old directory has a pending rmdir operation, we end up computing
a wrong path for the new inode, causing the receiver to fail.
Example reproducer:
$ cat test-send-rmdir.sh
#!/bin/bash
DEV=/dev/sdi
MNT=/mnt/sdi
mkfs.btrfs -f $DEV >/dev/null
mount $DEV $MNT
mkdir $MNT/dir
touch $MNT/dir/file1
touch $MNT/dir/file2
touch $MNT/dir/file3
# Filesystem looks like:
#
# . (ino 256)
# |----- dir/ (ino 257)
# |----- file1 (ino 258)
# |----- file2 (ino 259)
# |----- file3 (ino 260)
#
btrfs subvolume snapshot -r $MNT $MNT/snap1
btrfs send -f /tmp/snap1.send $MNT/snap1
# Now remove our directory and all its files.
rm -fr $MNT/dir
# Unmount the filesystem and mount it again. This is to ensure that
# the next inode that is created ends up with the same inode number
# that our directory "dir" had, 257, which is the first free "objectid"
# available after mounting again the filesystem.
umount $MNT
mount $DEV $MNT
# Now create a new file (it could be a directory as well).
touch $MNT/newfile
# Filesystem now looks like:
#
# . (ino 256)
# |----- newfile (ino 257)
#
btrfs subvolume snapshot -r $MNT $MNT/snap2
btrfs send -f /tmp/snap2.send -p $MNT/snap1 $MNT/snap2
# Now unmount the filesystem, create a new one, mount it and try to apply
# both send streams to recreate both snapshots.
umount $DEV
mkfs.btrfs -f $DEV >/dev/null
mount $DEV $MNT
btrfs receive -f /tmp/snap1.send $MNT
btrfs receive -f /tmp/snap2.send $MNT
umount $MNT
When running the test, the receive operation for the incremental stream
fails:
$ ./test-send-rmdir.sh
Create a readonly snapshot of '/mnt/sdi' in '/mnt/sdi/snap1'
At subvol /mnt/sdi/snap1
Create a readonly snapshot of '/mnt/sdi' in '/mnt/sdi/snap2'
At subvol /mnt/sdi/snap2
At subvol snap1
At snapshot snap2
ERROR: chown o257-9-0 failed: No such file or directory
So fix this by tracking directories that have a pending rmdir by inode
number and generation number, instead of only inode number.
A test case for fstests follows soon.
Reported-by: Massimo B. <massimo.b@gmx.net>
Tested-by: Massimo B. <massimo.b@gmx.net>
Link: https://lore.kernel.org/linux-btrfs/6ae34776e85912960a253a8327068a892998e685.camel@gmx.net/
CC: stable@vger.kernel.org # 4.19+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ae5e070eac upstream.
There is a chance of racing for qgroup flushing which may lead to
deadlock:
Thread A | Thread B
(not holding trans handle) | (holding a trans handle)
--------------------------------+--------------------------------
__btrfs_qgroup_reserve_meta() | __btrfs_qgroup_reserve_meta()
|- try_flush_qgroup() | |- try_flush_qgroup()
|- QGROUP_FLUSHING bit set | |
| | |- test_and_set_bit()
| | |- wait_event()
|- btrfs_join_transaction() |
|- btrfs_commit_transaction()|
!!! DEAD LOCK !!!
Since thread A wants to commit transaction, but thread B is holding a
transaction handle, blocking the commit.
At the same time, thread B is waiting for thread A to finish its commit.
This is just a hot fix, and would lead to more EDQUOT when we're near
the qgroup limit.
The proper fix would be to make all metadata/data reservations happen
without holding a transaction handle.
CC: stable@vger.kernel.org # 5.9+
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4bfd6247fa upstream.
Clevo W35xSS_370SS with VIA codec has had the runtime PM problem that
looses the power state of some nodes after the runtime resume. This
was worked around by disabling the default runtime PM via a denylist
entry. Since 5.10.x made the runtime PM applied (casually) even
though it's disabled in the denylist, this problem was revisited. The
result was that disabling power_save_node feature suffices for the
runtime PM problem.
This patch implements the disablement of power_save_node feature in
VIA codec for the device. It also drops the former denylist entry,
too, as the runtime PM should work in the codec side properly now.
Fixes: b529ef2464 ("ALSA: hda: Add Clevo W35xSS_370SS to the power_save blacklist")
Reported-by: Christian Labisch <clnetbox@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210104153046.19993-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d16baa3f14 upstream.
When initializing iocost for a queue, its rqos should be registered before
the blkcg policy is activated to allow policy data initiailization to lookup
the associated ioc. This unfortunately means that the rqos methods can be
called on bios before iocgs are attached to all existing blkgs.
While the race is theoretically possible on ioc_rqos_throttle(), it mostly
happened in ioc_rqos_merge() due to the difference in how they lookup ioc.
The former determines it from the passed in @rqos and then bails before
dereferencing iocg if the looked up ioc is disabled, which most likely is
the case if initialization is still in progress. The latter looked up ioc by
dereferencing the possibly NULL iocg making it a lot more prone to actually
triggering the bug.
* Make ioc_rqos_merge() use the same method as ioc_rqos_throttle() to look
up ioc for consistency.
* Make ioc_rqos_throttle() and ioc_rqos_merge() test for NULL iocg before
dereferencing it.
* Explain the danger of NULL iocgs in blk_iocost_init().
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Jonathan Lemon <bsd@fb.com>
Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ae28d1aae4 upstream.
Currently, when moving a task to a resource group the PQR_ASSOC MSR is
updated with the new closid and rmid in an added task callback. If the
task is running, the work is run as soon as possible. If the task is not
running, the work is executed later in the kernel exit path when the
kernel returns to the task again.
Updating the PQR_ASSOC MSR as soon as possible on the CPU a moved task
is running is the right thing to do. Queueing work for a task that is
not running is unnecessary (the PQR_ASSOC MSR is already updated when
the task is scheduled in) and causing system resource waste with the way
in which it is implemented: Work to update the PQR_ASSOC register is
queued every time the user writes a task id to the "tasks" file, even if
the task already belongs to the resource group.
This could result in multiple pending work items associated with a
single task even if they are all identical and even though only a single
update with most recent values is needed. Specifically, even if a task
is moved between different resource groups while it is sleeping then it
is only the last move that is relevant but yet a work item is queued
during each move.
This unnecessary queueing of work items could result in significant
system resource waste, especially on tasks sleeping for a long time.
For example, as demonstrated by Shakeel Butt in [1] writing the same
task id to the "tasks" file can quickly consume significant memory. The
same problem (wasted system resources) occurs when moving a task between
different resource groups.
As pointed out by Valentin Schneider in [2] there is an additional issue
with the way in which the queueing of work is done in that the task_struct
update is currently done after the work is queued, resulting in a race with
the register update possibly done before the data needed by the update is
available.
To solve these issues, update the PQR_ASSOC MSR in a synchronous way
right after the new closid and rmid are ready during the task movement,
only if the task is running. If a moved task is not running nothing
is done since the PQR_ASSOC MSR will be updated next time the task is
scheduled. This is the same way used to update the register when tasks
are moved as part of resource group removal.
[1] https://lore.kernel.org/lkml/CALvZod7E9zzHwenzf7objzGKsdBmVwTgEJ0nPgs0LUFU3SN5Pw@mail.gmail.com/
[2] https://lore.kernel.org/lkml/20201123022433.17905-1-valentin.schneider@arm.com
[ bp: Massage commit message and drop the two update_task_closid_rmid()
variants. ]
Fixes: e02737d5b8 ("x86/intel_rdt: Add tasks files")
Reported-by: Shakeel Butt <shakeelb@google.com>
Reported-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: James Morse <james.morse@arm.com>
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/17aa2fb38fc12ce7bb710106b3e7c7b45acb9e94.1608243147.git.reinette.chatre@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a889ea54b3 upstream.
Many TDP MMU functions which need to perform some action on all TDP MMU
roots hold a reference on that root so that they can safely drop the MMU
lock in order to yield to other threads. However, when releasing the
reference on the root, there is a bug: the root will not be freed even
if its reference count (root_count) is reduced to 0.
To simplify acquiring and releasing references on TDP MMU root pages, and
to ensure that these roots are properly freed, move the get/put operations
into another TDP MMU root iterator macro.
Moving the get/put operations into an iterator macro also helps
simplify control flow when a root does need to be freed. Note that using
the list_for_each_entry_safe macro would not have been appropriate in
this situation because it could keep a pointer to the next root across
an MMU lock release + reacquire, during which time that root could be
freed.
Reported-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Fixes: faaf05b00a ("kvm: x86/mmu: Support zapping SPTEs in the TDP MMU")
Fixes: 063afacd87 ("kvm: x86/mmu: Support invalidate range MMU notifier for TDP MMU")
Fixes: a6a0b05da9 ("kvm: x86/mmu: Support dirty logging for the TDP MMU")
Fixes: 1488199856 ("kvm: x86/mmu: Support disabling dirty logging for the tdp MMU")
Signed-off-by: Ben Gardon <bgardon@google.com>
Message-Id: <20210107001935.3732070-1-bgardon@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 88bf56d04b upstream.
In kvm_mmu_notifier_invalidate_range_start(), tlbs_dirty is used as:
need_tlb_flush |= kvm->tlbs_dirty;
with need_tlb_flush's type being int and tlbs_dirty's type being long.
It means that tlbs_dirty is always used as int and the higher 32 bits
is useless. We need to check tlbs_dirty in a correct way and this
change checks it directly without propagating it to need_tlb_flush.
Note: it's _extremely_ unlikely this neglecting of higher 32 bits can
cause problems in practice. It would require encountering tlbs_dirty
on a 4 billion count boundary, and KVM would need to be using shadow
paging or be running a nested guest.
Cc: stable@vger.kernel.org
Fixes: a4ee1ca4a3 ("KVM: MMU: delay flush all tlbs on sync_page path")
Signed-off-by: Lai Jiangshan <laijs@linux.alibaba.com>
Message-Id: <20201217154118.16497-1-jiangshanlai@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 39b4d43e60 upstream.
Get the so called "root" level from the low level shadow page table
walkers instead of manually attempting to calculate it higher up the
stack, e.g. in get_mmio_spte(). When KVM is using PAE shadow paging,
the starting level of the walk, from the callers perspective, is not
the CR3 root but rather the PDPTR "root". Checking for reserved bits
from the CR3 root causes get_mmio_spte() to consume uninitialized stack
data due to indexing into sptes[] for a level that was not filled by
get_walk(). This can result in false positives and/or negatives
depending on what garbage happens to be on the stack.
Opportunistically nuke a few extra newlines.
Fixes: 95fb5b0258 ("kvm: x86/mmu: Support MMIO in the TDP MMU")
Reported-by: Richard Herbert <rherbert@sympatico.ca>
Cc: Ben Gardon <bgardon@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20201218003139.2167891-3-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2aa078932f upstream.
Return -1 from the get_walk() helpers if the shadow walk doesn't fill at
least one spte, which can theoretically happen if the walk hits a
not-present PDPTR. Returning the root level in such a case will cause
get_mmio_spte() to return garbage (uninitialized stack data). In
practice, such a scenario should be impossible as KVM shouldn't get a
reserved-bit page fault with a not-present PDPTR.
Note, using mmu->root_level in get_walk() is wrong for other reasons,
too, but that's now a moot point.
Fixes: 95fb5b0258 ("kvm: x86/mmu: Support MMIO in the TDP MMU")
Cc: Ben Gardon <bgardon@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20201218003139.2167891-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d1c5246e08 upstream.
Commit
28ee90fe60 ("x86/mm: implement free pmd/pte page interfaces")
introduced a new location where a pmd was released, but neglected to
run the pmd page destructor. In fact, this happened previously for a
different pmd release path and was fixed by commit:
c283610e44 ("x86, mm: do not leak page->ptl for pmd page tables").
This issue was hidden until recently because the failure mode is silent,
but commit:
b2b29d6d01 ("mm: account PMD tables like PTE tables")
turns the failure mode into this signature:
BUG: Bad page state in process lt-pmem-ns pfn:15943d
page:000000007262ed7b refcount:0 mapcount:-1024 mapping:0000000000000000 index:0x0 pfn:0x15943d
flags: 0xaffff800000000()
raw: 00affff800000000 dead000000000100 0000000000000000 0000000000000000
raw: 0000000000000000 ffff913a029bcc08 00000000fffffbff 0000000000000000
page dumped because: nonzero mapcount
[..]
dump_stack+0x8b/0xb0
bad_page.cold+0x63/0x94
free_pcp_prepare+0x224/0x270
free_unref_page+0x18/0xd0
pud_free_pmd_page+0x146/0x160
ioremap_pud_range+0xe3/0x350
ioremap_page_range+0x108/0x160
__ioremap_caller.constprop.0+0x174/0x2b0
? memremap+0x7a/0x110
memremap+0x7a/0x110
devm_memremap+0x53/0xa0
pmem_attach_disk+0x4ed/0x530 [nd_pmem]
? __devm_release_region+0x52/0x80
nvdimm_bus_probe+0x85/0x210 [libnvdimm]
Given this is a repeat occurrence it seemed prudent to look for other
places where this destructor might be missing and whether a better
helper is needed. try_to_free_pmd_page() looks like a candidate, but
testing with setting up and tearing down pmd mappings via the dax unit
tests is thus far not triggering the failure.
As for a better helper pmd_free() is close, but it is a messy fit
due to requiring an @mm arg. Also, ___pmd_free_tlb() wants to call
paravirt_tlb_remove_table() instead of free_page(), so open-coded
pgtable_pmd_page_dtor() seems the best way forward for now.
Debugged together with Matthew Wilcox <willy@infradead.org>.
Fixes: 28ee90fe60 ("x86/mm: implement free pmd/pte page interfaces")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Tested-by: Yi Zhang <yi.zhang@redhat.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/160697689204.605323.17629854984697045602.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2407cf7d2 upstream.
Ever since commit 2a9127fcf2 ("mm: rewrite wait_on_page_bit_common()
logic") we've had some very occasional reports of BUG_ON(PageWriteback)
in write_cache_pages(), which we thought we already fixed in commit
073861ed77 ("mm: fix VM_BUG_ON(PageTail) and BUG_ON(PageWriteback)").
But syzbot just reported another one, even with that commit in place.
And it turns out that there's a simpler way to trigger the BUG_ON() than
the one Hugh found with page re-use. It all boils down to the fact that
the page writeback is ostensibly serialized by the page lock, but that
isn't actually really true.
Yes, the people _setting_ writeback all do so under the page lock, but
the actual clearing of the bit - and waking up any waiters - happens
without any page lock.
This gives us this fairly simple race condition:
CPU1 = end previous writeback
CPU2 = start new writeback under page lock
CPU3 = write_cache_pages()
CPU1 CPU2 CPU3
---- ---- ----
end_page_writeback()
test_clear_page_writeback(page)
... delayed...
lock_page();
set_page_writeback()
unlock_page()
lock_page()
wait_on_page_writeback();
wake_up_page(page, PG_writeback);
.. wakes up CPU3 ..
BUG_ON(PageWriteback(page));
where the BUG_ON() happens because we woke up the PG_writeback bit
becasue of the _previous_ writeback, but a new one had already been
started because the clearing of the bit wasn't actually atomic wrt the
actual wakeup or serialized by the page lock.
The reason this didn't use to happen was that the old logic in waiting
on a page bit would just loop if it ever saw the bit set again.
The nice proper fix would probably be to get rid of the whole "wait for
writeback to clear, and then set it" logic in the writeback path, and
replace it with an atomic "wait-to-set" (ie the same as we have for page
locking: we set the page lock bit with a single "lock_page()", not with
"wait for lock bit to clear and then set it").
However, out current model for writeback is that the waiting for the
writeback bit is done by the generic VFS code (ie write_cache_pages()),
but the actual setting of the writeback bit is done much later by the
filesystem ".writepages()" function.
IOW, to make the writeback bit have that same kind of "wait-to-set"
behavior as we have for page locking, we'd have to change our roughly
~50 different writeback functions. Painful.
Instead, just make "wait_on_page_writeback()" loop on the very unlikely
situation that the PG_writeback bit is still set, basically re-instating
the old behavior. This is very non-optimal in case of contention, but
since we only ever set the bit under the page lock, that situation is
controlled.
Reported-by: syzbot+2fc0712f8f8b8b8fa0ef@syzkaller.appspotmail.com
Fixes: 2a9127fcf2 ("mm: rewrite wait_on_page_bit_common() logic")
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove an unused variable which was mistakingly left by commit
37faf50615 ("USB: serial: keyspan_pda: fix write-wakeup
use-after-free") and only removed by a later change.
This is needed to suppress a W=1 warning about the unused variable in
the stable trees that the build bots triggers.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 64e6bbfff5 upstream.
There is a use-after-free issue, if access udc_name
in function gadget_dev_desc_UDC_store after another context
free udc_name in function unregister_gadget.
Context 1:
gadget_dev_desc_UDC_store()->unregister_gadget()->
free udc_name->set udc_name to NULL
Context 2:
gadget_dev_desc_UDC_show()-> access udc_name
Call trace:
dump_backtrace+0x0/0x340
show_stack+0x14/0x1c
dump_stack+0xe4/0x134
print_address_description+0x78/0x478
__kasan_report+0x270/0x2ec
kasan_report+0x10/0x18
__asan_report_load1_noabort+0x18/0x20
string+0xf4/0x138
vsnprintf+0x428/0x14d0
sprintf+0xe4/0x12c
gadget_dev_desc_UDC_show+0x54/0x64
configfs_read_file+0x210/0x3a0
__vfs_read+0xf0/0x49c
vfs_read+0x130/0x2b4
SyS_read+0x114/0x208
el0_svc_naked+0x34/0x38
Add mutex_lock to protect this kind of scenario.
Signed-off-by: Eddie Hung <eddie.hung@mediatek.com>
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1609239215-21819-1-git-send-email-macpaul.lin@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6cd0fe9138 upstream.
When binding the ConfigFS gadget to a UDC, the functions in each
configuration are added in list order. However, if usb_add_function()
fails, the failed function is put back on its configuration's
func_list and purge_configs_funcs() is called to further clean up.
purge_configs_funcs() iterates over the configurations and functions
in forward order, calling unbind() on each of the previously added
functions. But after doing so, each function gets moved to the
tail of the configuration's func_list. This results in reshuffling
the original order of the functions within a configuration such
that the failed function now appears first even though it may have
originally appeared in the middle or even end of the list. At this
point if the ConfigFS gadget is attempted to re-bind to the UDC,
the functions will be added in a different order than intended,
with the only recourse being to remove and relink the functions all
over again.
An example of this as follows:
ln -s functions/mass_storage.0 configs/c.1
ln -s functions/ncm.0 configs/c.1
ln -s functions/ffs.adb configs/c.1 # oops, forgot to start adbd
echo "<udc device>" > UDC # fails
start adbd
echo "<udc device>" > UDC # now succeeds, but...
# bind order is
# "ADB", mass_storage, ncm
[30133.118289] configfs-gadget gadget: adding 'Mass Storage Function'/ffffff810af87200 to config 'c'/ffffff817d6a2520
[30133.119875] configfs-gadget gadget: adding 'cdc_network'/ffffff80f48d1a00 to config 'c'/ffffff817d6a2520
[30133.119974] using random self ethernet address
[30133.120002] using random host ethernet address
[30133.139604] usb0: HOST MAC 3e:27:46:ba:3e:26
[30133.140015] usb0: MAC 6e:28:7e:42:66:6a
[30133.140062] configfs-gadget gadget: adding 'Function FS Gadget'/ffffff80f3868438 to config 'c'/ffffff817d6a2520
[30133.140081] configfs-gadget gadget: adding 'Function FS Gadget'/ffffff80f3868438 --> -19
[30133.140098] configfs-gadget gadget: unbind function 'Mass Storage Function'/ffffff810af87200
[30133.140119] configfs-gadget gadget: unbind function 'cdc_network'/ffffff80f48d1a00
[30133.173201] configfs-gadget a600000.dwc3: failed to start g1: -19
[30136.661933] init: starting service 'adbd'...
[30136.700126] read descriptors
[30136.700413] read strings
[30138.574484] configfs-gadget gadget: adding 'Function FS Gadget'/ffffff80f3868438 to config 'c'/ffffff817d6a2520
[30138.575497] configfs-gadget gadget: adding 'Mass Storage Function'/ffffff810af87200 to config 'c'/ffffff817d6a2520
[30138.575554] configfs-gadget gadget: adding 'cdc_network'/ffffff80f48d1a00 to config 'c'/ffffff817d6a2520
[30138.575631] using random self ethernet address
[30138.575660] using random host ethernet address
[30138.595338] usb0: HOST MAC 2e:cf:43:cd:ca:c8
[30138.597160] usb0: MAC 6a:f0:9f:ee:82:a0
[30138.791490] configfs-gadget gadget: super-speed config #1: c
Fix this by reversing the iteration order of the functions in
purge_config_funcs() when unbinding them, and adding them back to
the config's func_list at the head instead of the tail. This
ensures that we unbind and unwind back to the original list order.
Fixes: 88af8bbe4e ("usb: gadget: the start of the configfs interface")
Signed-off-by: Chandana Kishori Chiluveru <cchiluve@codeaurora.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20201229224443.31623-1-jackp@codeaurora.org
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5cc35c224a upstream.
There is a spinlock lockup as part of composite_disconnect
when it tries to acquire cdev->lock as part of usb_gadget_deactivate.
This is because the usb_gadget_deactivate is called from
usb_function_deactivate with the same spinlock held.
This would result in the below call stack and leads to stall.
rcu: INFO: rcu_preempt detected stalls on CPUs/tasks:
rcu: 3-...0: (1 GPs behind) idle=162/1/0x4000000000000000
softirq=10819/10819 fqs=2356
(detected by 2, t=5252 jiffies, g=20129, q=3770)
Task dump for CPU 3:
task:uvc-gadget_wlhe state:R running task stack: 0 pid: 674 ppid:
636 flags:0x00000202
Call trace:
__switch_to+0xc0/0x170
_raw_spin_lock_irqsave+0x84/0xb0
composite_disconnect+0x28/0x78
configfs_composite_disconnect+0x68/0x70
usb_gadget_disconnect+0x10c/0x128
usb_gadget_deactivate+0xd4/0x108
usb_function_deactivate+0x6c/0x80
uvc_function_disconnect+0x20/0x58
uvc_v4l2_release+0x30/0x88
v4l2_release+0xbc/0xf0
__fput+0x7c/0x230
____fput+0x14/0x20
task_work_run+0x88/0x140
do_notify_resume+0x240/0x6f0
work_pending+0x8/0x200
Fix this by doing an unlock on cdev->lock before the usb_gadget_deactivate
call from usb_function_deactivate.
The same lockup can happen in the usb_gadget_activate path. Fix that path
as well.
Reported-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/linux-usb/20201102094936.GA29581@b29397-desktop/
Tested-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Sriharsha Allenki <sallenki@codeaurora.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201202130220.24926-1-sallenki@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0a88fa221c upstream.
Fix the MTU size issue with RX packet size as the host sends the packet
with extra bytes containing ethernet header. This causes failure when
user sets the MTU size to the maximum i.e. 15412. In this case the
ethernet packet received will be of length 15412 plus the ethernet header
length. This patch fixes the issue where there is a check that RX packet
length must not be more than max packet length.
Fixes: bba787a860 ("usb: gadget: ether: Allow jumbo frames")
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1605597215-122027-1-git-send-email-manish.narani@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9389044f27 upstream.
With commit 913e4a90b6 ("usb: gadget: f_uac2: finalize wMaxPacketSize according to bandwidth")
wMaxPacketSize is computed dynamically but the value is never reset.
Because of this, the actual maximum packet size can only decrease each time
the audio gadget is instantiated.
Reset the endpoint maximum packet size and mark wMaxPacketSize as dynamic
to solve the problem.
Fixes: 913e4a90b6 ("usb: gadget: f_uac2: finalize wMaxPacketSize according to bandwidth")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201221173531.215169-2-jbrunet@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c318840fb2 upstream.
The dummy-hcd driver was written under the assumption that all the
parameters in URBs sent to its root hub would be valid. With URBs
sent from userspace via usbfs, that assumption can be violated.
In particular, the driver doesn't fully check the port-feature values
stored in the wValue entry of Clear-Port-Feature and Set-Port-Feature
requests. Values that are too large can cause the driver to perform
an invalid left shift of more than 32 bits. Ironically, two of those
left shifts are unnecessary, because they implement Set-Port-Feature
requests that hubs are not required to support, according to section
11.24.2.13 of the USB-2.0 spec.
This patch adds the appropriate checks for the port feature selector
values and removes the unnecessary feature settings. It also rejects
requests to set the TEST feature or to set or clear the INDICATOR and
C_OVERCURRENT features, as none of these are relevant to dummy-hcd's
root-hub emulation.
CC: <stable@vger.kernel.org>
Reported-and-tested-by: syzbot+5925509f78293baa7331@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20201230162044.GA727759@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 020a1f4534 upstream.
Stack-allocated buffers cannot be used for DMA (on all architectures).
Replace the HP-channel macro with a helper function that allocates a
dedicated transfer buffer so that it can continue to be used with
arguments from the stack.
Note that the buffer is cleared on allocation as usblp_ctrl_msg()
returns success also on short transfers (the buffer is only used for
debugging).
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210104145302.2087-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 372c931319 upstream.
Make sure to always cancel the control URB in write() so that it can be
reused after a timeout or spurious CMD_ACK.
Currently any further write requests after a timeout would fail after
triggering a WARN() in usb_submit_urb() when attempting to submit the
already active URB.
Reported-by: syzbot+e87ebe0f7913f71f2ea5@syzkaller.appspotmail.com
Fixes: 6bc235a2e2 ("USB: add driver for Meywa-Denki & Kayac YUREX")
Cc: stable <stable@vger.kernel.org> # 2.6.37
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d5323a6f3 upstream.
The commit 0472bf06c6 ("xhci: Prevent U1/U2 link pm states if exit
latency is too long") was constraining the xhci code not to allow U1/U2
sleep states if the latency to wake up from the U-states reached the
service interval of an periodic endpoint. This fix was not taking into
account that in case the quirk XHCI_INTEL_HOST is set, the wakeup time
will be calculated and configured differently.
It checks for u1_params.mel/u2_params.mel as a limit. But the code could
decide to write another MEL into the hardware. This leads to broken
cases where not enough bandwidth is available for other devices:
usb 1-2: can't set config #1, error -28
This patch is fixing that case by checking for timeout_ns after the
wakeup time was calculated depending on the quirks.
Fixes: 0472bf06c6 ("xhci: Prevent U1/U2 link pm states if exit latency is too long")
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201215193147.11738-1-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e5f4ca3fce upstream.
First of all the commit e0082698b6 ("usb: dwc3: ulpi: conditionally
resume ULPI PHY") introduced the Suspend USB2.0 HS/FS/LS PHY regression,
as by design of the fix any attempt to read/write from/to the PHY control
registers will completely disable the PHY suspension, which consequently
will increase the USB bus power consumption. Secondly the fix won't work
well for the very first attempt of the ULPI PHY control registers IO,
because after disabling the USB2.0 PHY suspension functionality it will
still take some time for the bus to resume from the sleep state if one has
been reached before it. So the very first PHY register read/write
operation will take more time than the busy-loop provides and the IO
timeout error might be returned anyway.
Here we suggest to fix the denoted problems in the following way. First of
all let's not disable the Suspend USB2.0 HS/FS/LS PHY functionality so to
make the controller and the USB2.0 bus more power efficient. Secondly
instead of that we'll extend the PHY IO op wait procedure with 1 - 1.2 ms
sleep if the PHY suspension is enabled (1ms should be enough as by LPM
specification it is at most how long it takes for the USB2.0 bus to resume
from L1 (Sleep) state). Finally in case if the USB2.0 PHY suspension
functionality has been disabled on the DWC USB3 controller setup procedure
we'll compensate the USB bus resume process latency by extending the
busy-loop attempts counter.
Fixes: e0082698b6 ("usb: dwc3: ulpi: conditionally resume ULPI PHY")
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201210085008.13264-4-Sergey.Semin@baikalelectronics.ru
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fca3f13810 upstream.
Originally the procedure of the ULPI transaction finish detection has been
developed as a simple busy-loop with just decrementing counter and no
delays. It's wrong since on different systems the loop will take a
different time to complete. So if the system bus and CPU are fast enough
to overtake the ULPI bus and the companion PHY reaction, then we'll get to
take a false timeout error. Fix this by converting the busy-loop procedure
to take the standard bus speed, address value and the registers access
mode into account for the busy-loop delay calculation.
Here is the way the fix works. It's known that the ULPI bus is clocked
with 60MHz signal. In accordance with [1] the ULPI bus protocol is created
so to spend 5 and 6 clock periods for immediate register write and read
operations respectively, and 6 and 7 clock periods - for the extended
register writes and reads. Based on that we can easily pre-calculate the
time which will be needed for the controller to perform a requested IO
operation. Note we'll still preserve the attempts counter in case if the
DWC USB3 controller has got some internals delays.
[1] UTMI+ Low Pin Interface (ULPI) Specification, Revision 1.1,
October 20, 2004, pp. 30 - 36.
Fixes: 88bc9d194f ("usb: dwc3: add ULPI interface support")
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201210085008.13264-3-Sergey.Semin@baikalelectronics.ru
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce722da66d upstream.
In accordance with [1] the DWC_usb3 core sets the GUSB2PHYACCn.VStsDone
bit when the PHY vendor control access is done and clears it when the
application initiates a new transaction. The doc doesn't say anything
about the GUSB2PHYACCn.VStsBsy flag serving for the same purpose. Moreover
we've discovered that the VStsBsy flag can be cleared before the VStsDone
bit. So using the former as a signal of the PHY control registers
completion might be dangerous. Let's have the VStsDone flag utilized
instead then.
[1] Synopsys DesignWare Cores SuperSpeed USB 3.0 xHCI Host Controller
Databook, 2.70a, December 2013, p.388
Fixes: 88bc9d194f ("usb: dwc3: add ULPI interface support")
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201210085008.13264-2-Sergey.Semin@baikalelectronics.ru
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f041b8592 upstream.
Warm reboot scenarios some times type C Mux driver gets Mux configuration
request as HPD=1,IRQ=1. In that scenario typeC Mux driver need to configure
Mux as follows as per IOM requirement:
(1). Confgiure Mux HPD = 1, IRQ = 0
(2). Configure Mux with HPD = 1, IRQ = 1
IOM expects TypeC Mux configuration as follows:
(1). HPD=1, IRQ=0
(2). HPD=1, IRQ=1
if IOM gets mux config request (2) without configuring (1), it will ignore
the request. The impact of this is there is no DP_alt mode display.
Fixes: 43d596e322 ("usb: typec: intel_pmc_mux: Check the port status before connect")
Cc: stable@vger.kernel.org
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Madhusudanarao Amara <madhusudanarao.amara@intel.com>
Link: https://lore.kernel.org/r/20201216140918.49197-1-madhusudanarao.amara@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e5ff0b4b6 upstream.
syzbot is reporting UAF at usb_submit_urb() [1], for
service_outstanding_interrupt() is not checking WDM_DISCONNECTING
before calling usb_submit_urb(). Close the race by doing same checks
wdm_read() does upon retry.
Also, while wdm_read() checks WDM_DISCONNECTING with desc->rlock held,
service_interrupt_work() does not hold desc->rlock. Thus, it is possible
that usb_submit_urb() is called from service_outstanding_interrupt() from
service_interrupt_work() after WDM_DISCONNECTING was set and kill_urbs()
from wdm_disconnect() completed. Thus, move kill_urbs() in
wdm_disconnect() to after cancel_work_sync() (which makes sure that
service_interrupt_work() is no longer running) completed.
Although it seems to be safe to dereference desc->intf->dev in
service_outstanding_interrupt() even if WDM_DISCONNECTING was already set
because desc->rlock or cancel_work_sync() prevents wdm_disconnect() from
reaching list_del() before service_outstanding_interrupt() completes,
let's not emit error message if WDM_DISCONNECTING is set by
wdm_disconnect() while usb_submit_urb() is in progress.
[1] https://syzkaller.appspot.com/bug?extid=9e04e2df4a32fb661daf
Reported-by: syzbot <syzbot+9e04e2df4a32fb661daf@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/620e2ee0-b9a3-dbda-a25b-a93e0ed03ec5@i-love.sakura.ne.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e2459108b5 upstream.
Enable Super speed plus in configfs to support USB3.1 Gen2.
This ensures that when a USB gadget is plugged in, it is
enumerated as Gen 2 and connected at 10 Gbps if the host and
cable are capable of it.
Many in-tree gadget functions (fs, midi, acm, ncm, mass_storage,
etc.) already have SuperSpeed Plus support.
Tested: plugged gadget into Linux host and saw:
[284907.385986] usb 8-2: new SuperSpeedPlus Gen 2 USB device number 3 using xhci_hcd
Tested-by: Lorenzo Colitti <lorenzo@google.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: taehyun.cho <taehyun.cho@samsung.com>
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Link: https://lore.kernel.org/r/20210106154625.2801030-1-lorenzo@google.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ce47d95b7 upstream.
Commit eff8728fe6 ("vmlinux.lds.h: Add PGO and AutoFDO input
sections") added ".text.unlikely.*" and ".text.hot.*" due to an LLVM
change [1].
After another LLVM change [2], these sections are seen in some PowerPC
builds, where there is a orphan section warning then build failure:
$ make -skj"$(nproc)" \
ARCH=powerpc CROSS_COMPILE=powerpc64le-linux-gnu- LLVM=1 O=out \
distclean powernv_defconfig zImage.epapr
ld.lld: warning: kernel/built-in.a(panic.o):(.text.unlikely.) is being placed in '.text.unlikely.'
...
ld.lld: warning: address (0xc000000000009314) of section .text is not a multiple of alignment (256)
...
ERROR: start_text address is c000000000009400, should be c000000000008000
ERROR: try to enable LD_HEAD_STUB_CATCH config option
ERROR: see comments in arch/powerpc/tools/head_check.sh
...
Explicitly handle these sections like in the main linker script so
there is no more build failure.
[1]: https://reviews.llvm.org/D79600
[2]: https://reviews.llvm.org/D92493
Fixes: 83a092cf95 ("powerpc: Link warning for orphan sections")
Cc: stable@vger.kernel.org
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://github.com/ClangBuiltLinux/linux/issues/1218
Link: https://lore.kernel.org/r/20210104205952.1399409-1-natechancellor@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0aa171e9b2 upstream.
Pavel reports that commit 17858b140b ("crypto: ecdh - avoid unaligned
accesses in ecdh_set_secret()") fixes one problem but introduces another:
the unconditional memcpy() introduced by that commit may overflow the
target buffer if the source data is invalid, which could be the result of
intentional tampering.
So check params.key_size explicitly against the size of the target buffer
before validating the key further.
Fixes: 17858b140b ("crypto: ecdh - avoid unaligned accesses in ecdh_set_secret()")
Reported-by: Pavel Machek <pavel@denx.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 52abca64fd ]
blk_queue_enter() accepts BLK_MQ_REQ_PM requests independent of the runtime
power management state. Now that SCSI domain validation no longer depends
on this behavior, modify the behavior of blk_queue_enter() as follows:
- Do not accept any requests while suspended.
- Only process power management requests while suspending or resuming.
Submitting BLK_MQ_REQ_PM requests to a device that is runtime suspended
causes runtime-suspended devices not to resume as they should. The request
which should cause a runtime resume instead gets issued directly, without
resuming the device first. Of course the device can't handle it properly,
the I/O fails, and the device remains suspended.
The problem is fixed by checking that the queue's runtime-PM status isn't
RPM_SUSPENDED before allowing a request to be issued, and queuing a
runtime-resume request if it is. In particular, the inline
blk_pm_request_resume() routine is renamed blk_pm_resume_queue() and the
code is unified by merging the surrounding checks into the routine. If the
queue isn't set up for runtime PM, or there currently is no restriction on
allowed requests, the request is allowed. Likewise if the BLK_MQ_REQ_PM
flag is set and the status isn't RPM_SUSPENDED. Otherwise a runtime resume
is queued and the request is blocked until conditions are more suitable.
[ bvanassche: modified commit message and removed Cc: stable because
without the previous patches from this series this patch would break
parallel SCSI domain validation + introduced queue_rpm_status() ]
Link: https://lore.kernel.org/r/20201209052951.16136-9-bvanassche@acm.org
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Can Guo <cang@codeaurora.org>
Cc: Stanley Chu <stanley.chu@mediatek.com>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reported-and-tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5c3b579686 upstream.
There have been multiple revisions of the patch fix the h5->rx_skb
leak. Accidentally the first revision (which is buggy) and v5 have
both been merged:
v1 commit 70f259a3f4 ("Bluetooth: hci_h5: close serdev device and free
hu in h5_close");
v5 commit 855af2d74c ("Bluetooth: hci_h5: fix memory leak in h5_close")
The correct v5 makes changes slightly higher up in the h5_close()
function, which allowed both versions to get merged without conflict.
The changes from v1 unconditionally frees the h5 data struct, this
is wrong because in the serdev enumeration case the memory is
allocated in h5_serdev_probe() like this:
h5 = devm_kzalloc(dev, sizeof(*h5), GFP_KERNEL);
So its lifetime is tied to the lifetime of the driver being bound
to the serdev and it is automatically freed when the driver gets
unbound. In the serdev case the same h5 struct is re-used over
h5_close() and h5_open() calls and thus MUST not be free-ed in
h5_close().
The serdev_device_close() added to h5_close() is incorrect in the
same way, serdev_device_close() is called on driver unbound too and
also MUST no be called from h5_close().
This reverts the changes made by merging v1 of the patch, so that
just the changes of the correct v5 remain.
Cc: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 436e980e2e upstream.
depmod is not guaranteed to be in /sbin, just let make look for
it in the path like all the other invoked programs
Signed-off-by: Dominique Martinet <asmadeus@codewreck.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cedd1862be ]
Commit 436e980e2e ("kbuild: don't hardcode depmod path") stopped
hard-coding the path of depmod, but in the process caused trouble for
distributions that had that /sbin location, but didn't have it in the
PATH (generally because /sbin is limited to the super-user path).
Work around it for now by just adding /sbin to the end of PATH in the
depmod.sh script.
Reported-and-tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3684566384 ]
Some graphic card has very big memory on chip, such as 32G bytes.
In the following case, it will cause overflow:
pool = gen_pool_create(PAGE_SHIFT, NUMA_NO_NODE);
ret = gen_pool_add(pool, 0x1000000, SZ_32G, NUMA_NO_NODE);
va = gen_pool_alloc(pool, SZ_4G);
The overflow occurs in gen_pool_alloc_algo_owner():
....
size = nbits << order;
....
The @nbits is "int" type, so it will overflow.
Then the gen_pool_avail() will return the wrong value.
This patch converts some "int" to "unsigned long", and
changes the compare code in while.
Link: https://lkml.kernel.org/r/20201229060657.3389-1-sjhuang@iluvatar.ai
Signed-off-by: Huang Shijie <sjhuang@iluvatar.ai>
Reported-by: Shi Jiasheng <jiasheng.shi@iluvatar.ai>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 96d86e6a80 ]
RQF_PREEMPT is used for two different purposes in the legacy IDE code:
1. To mark power management requests.
2. To mark requests that should preempt another request. An (old)
explanation of that feature is as follows: "The IDE driver in the Linux
kernel normally uses a series of busywait delays during its
initialization. When the driver executes these busywaits, the kernel
does nothing for the duration of the wait. The time spent in these
waits could be used for other initialization activities, if they could
be run concurrently with these waits.
More specifically, busywait-style delays such as udelay() in module
init functions inhibit kernel preemption because the Big Kernel Lock is
held, while yielding APIs such as schedule_timeout() allow
preemption. This is true because the kernel handles the BKL specially
and releases and reacquires it across reschedules allowed by the
current thread.
This IDE-preempt specification requires that the driver eliminate these
busywaits and replace them with a mechanism that allows other work to
proceed while the IDE driver is initializing."
Since I haven't found an implementation of (2), do not set the PREEMPT flag
for sense requests. This patch causes sense requests to be postponed while
a drive is suspended instead of being submitted to ide_queue_rq().
If it would ever be necessary to restore the IDE PREEMPT functionality,
that can be done by introducing a new flag in struct ide_request.
Link: https://lore.kernel.org/r/20201209052951.16136-4-bvanassche@acm.org
Cc: David S. Miller <davem@davemloft.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Can Guo <cang@codeaurora.org>
Cc: Stanley Chu <stanley.chu@mediatek.com>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c763729a10 ]
Currently, ufshcd-pci is the only UFS driver with support for
suspend-to-disk PM callbacks (i.e. freeze/thaw/restore/poweroff). These
callbacks are set by the macro SET_SYSTEM_SLEEP_PM_OPS to the same
functions as system suspend/resume. That will work with spm_lvl 5 because
spm_lvl 5 will result in a full restore for the ->restore() callback. In
the absence of a full restore, the host controller registers will have
values set up by the restore kernel (the kernel that boots and loads the
restore image) which are not necessarily the same. However it turns out,
the only registers that sometimes need restore are the base address
registers. This has gone un-noticed because, depending on IOMMU settings,
the kernel can end up allocating the same addresses every time.
For Intel controllers, an spm_lvl other than 5 can be used, so to support
S4 (suspend-to-disk) with spm_lvl other than 5, restore the base address
registers.
Link: https://lore.kernel.org/r/20201207083120.26732-2-adrian.hunter@intel.com
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 01341fbd0d ]
In realtime scenario, We do not want to have interference on the
isolated cpu cores. but when invoking alloc_workqueue() for percpu wq
on the housekeeping cpu, it kick a kworker on the isolated cpu.
alloc_workqueue
pwq_adjust_max_active
wake_up_worker
The comment in pwq_adjust_max_active() said:
"Need to kick a worker after thawed or an unbound wq's
max_active is bumped"
So it is unnecessary to kick a kworker for percpu's wq when invoking
alloc_workqueue(). this patch only kick a worker based on the actual
activation of delayed works.
Signed-off-by: Yunfeng Ye <yeyunfeng@huawei.com>
Reviewed-by: Lai Jiangshan <jiangshanlai@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59b4a8fa27 ]
The cdc_ncm driver passes network connection notifications up to
usbnet_link_change(), which is the right place for any logging.
Remove the netdev_info() duplicating this from the driver itself.
This stops devices such as my "TRENDnet USB 10/100/1G/2.5G LAN"
(ID 20f4:e02b) adapter from spamming the kernel log with
cdc_ncm 2-2:2.0 enp0s2u2c2: network connection: connected
messages every 60 msec or so.
Signed-off-by: Roland Dreier <roland@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20201224032116.2453938-1-roland@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 709a3c9dff ]
There is one GSWIP_MII_CFG register for each switch-port except the CPU
port. The register offset for the first port is 0x0, 0x02 for the
second, 0x04 for the third and so on.
Update the driver to not only restrict the GSWIP_MII_CFG registers to
ports 0, 1 and 5. Handle ports 0..5 instead but skip the CPU port. This
means we are not overwriting the configuration for the third port (port
two since we start counting from zero) with the settings for the sixth
port (with number five) anymore.
The GSWIP_MII_PCDU(p) registers are not updated because there's really
only three (one for each of the following ports: 0, 1, 5).
Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c1a9ec7e5d ]
Enable GSWIP_MII_CFG_EN also for internal PHYs to make traffic flow.
Without this the PHY link is detected properly and ethtool statistics
for TX are increasing but there's no RX traffic coming in.
Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Suggested-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d9e4498173 ]
Like other tunneling interfaces, the bareudp doesn't need TXLOCK.
So, It is good to set the NETIF_F_LLTX flag to improve performance and
to avoid lockdep's false-positive warning.
Test commands:
ip netns add A
ip netns add B
ip link add veth0 netns A type veth peer name veth1 netns B
ip netns exec A ip link set veth0 up
ip netns exec A ip a a 10.0.0.1/24 dev veth0
ip netns exec B ip link set veth1 up
ip netns exec B ip a a 10.0.0.2/24 dev veth1
for i in {2..1}
do
let A=$i-1
ip netns exec A ip link add bareudp$i type bareudp \
dstport $i ethertype ip
ip netns exec A ip link set bareudp$i up
ip netns exec A ip a a 10.0.$i.1/24 dev bareudp$i
ip netns exec A ip r a 10.0.$i.2 encap ip src 10.0.$A.1 \
dst 10.0.$A.2 via 10.0.$i.2 dev bareudp$i
ip netns exec B ip link add bareudp$i type bareudp \
dstport $i ethertype ip
ip netns exec B ip link set bareudp$i up
ip netns exec B ip a a 10.0.$i.2/24 dev bareudp$i
ip netns exec B ip r a 10.0.$i.1 encap ip src 10.0.$A.2 \
dst 10.0.$A.1 via 10.0.$i.1 dev bareudp$i
done
ip netns exec A ping 10.0.2.2
Splat looks like:
[ 96.992803][ T822] ============================================
[ 96.993954][ T822] WARNING: possible recursive locking detected
[ 96.995102][ T822] 5.10.0+ #819 Not tainted
[ 96.995927][ T822] --------------------------------------------
[ 96.997091][ T822] ping/822 is trying to acquire lock:
[ 96.998083][ T822] ffff88810f753898 (_xmit_NONE#2){+.-.}-{2:2}, at: __dev_queue_xmit+0x1f52/0x2960
[ 96.999813][ T822]
[ 96.999813][ T822] but task is already holding lock:
[ 97.001192][ T822] ffff88810c385498 (_xmit_NONE#2){+.-.}-{2:2}, at: __dev_queue_xmit+0x1f52/0x2960
[ 97.002908][ T822]
[ 97.002908][ T822] other info that might help us debug this:
[ 97.004401][ T822] Possible unsafe locking scenario:
[ 97.004401][ T822]
[ 97.005784][ T822] CPU0
[ 97.006407][ T822] ----
[ 97.007010][ T822] lock(_xmit_NONE#2);
[ 97.007779][ T822] lock(_xmit_NONE#2);
[ 97.008550][ T822]
[ 97.008550][ T822] *** DEADLOCK ***
[ 97.008550][ T822]
[ 97.010057][ T822] May be due to missing lock nesting notation
[ 97.010057][ T822]
[ 97.011594][ T822] 7 locks held by ping/822:
[ 97.012426][ T822] #0: ffff888109a144f0 (sk_lock-AF_INET){+.+.}-{0:0}, at: raw_sendmsg+0x12f7/0x2b00
[ 97.014191][ T822] #1: ffffffffbce2f5a0 (rcu_read_lock_bh){....}-{1:2}, at: ip_finish_output2+0x249/0x2020
[ 97.016045][ T822] #2: ffffffffbce2f5a0 (rcu_read_lock_bh){....}-{1:2}, at: __dev_queue_xmit+0x1fd/0x2960
[ 97.017897][ T822] #3: ffff88810c385498 (_xmit_NONE#2){+.-.}-{2:2}, at: __dev_queue_xmit+0x1f52/0x2960
[ 97.019684][ T822] #4: ffffffffbce2f600 (rcu_read_lock){....}-{1:2}, at: bareudp_xmit+0x31b/0x3690 [bareudp]
[ 97.021573][ T822] #5: ffffffffbce2f5a0 (rcu_read_lock_bh){....}-{1:2}, at: ip_finish_output2+0x249/0x2020
[ 97.023424][ T822] #6: ffffffffbce2f5a0 (rcu_read_lock_bh){....}-{1:2}, at: __dev_queue_xmit+0x1fd/0x2960
[ 97.025259][ T822]
[ 97.025259][ T822] stack backtrace:
[ 97.026349][ T822] CPU: 3 PID: 822 Comm: ping Not tainted 5.10.0+ #819
[ 97.027609][ T822] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
[ 97.029407][ T822] Call Trace:
[ 97.030015][ T822] dump_stack+0x99/0xcb
[ 97.030783][ T822] __lock_acquire.cold.77+0x149/0x3a9
[ 97.031773][ T822] ? stack_trace_save+0x81/0xa0
[ 97.032661][ T822] ? register_lock_class+0x1910/0x1910
[ 97.033673][ T822] ? register_lock_class+0x1910/0x1910
[ 97.034679][ T822] ? rcu_read_lock_sched_held+0x91/0xc0
[ 97.035697][ T822] ? rcu_read_lock_bh_held+0xa0/0xa0
[ 97.036690][ T822] lock_acquire+0x1b2/0x730
[ 97.037515][ T822] ? __dev_queue_xmit+0x1f52/0x2960
[ 97.038466][ T822] ? check_flags+0x50/0x50
[ 97.039277][ T822] ? netif_skb_features+0x296/0x9c0
[ 97.040226][ T822] ? validate_xmit_skb+0x29/0xb10
[ 97.041151][ T822] _raw_spin_lock+0x30/0x70
[ 97.041977][ T822] ? __dev_queue_xmit+0x1f52/0x2960
[ 97.042927][ T822] __dev_queue_xmit+0x1f52/0x2960
[ 97.043852][ T822] ? netdev_core_pick_tx+0x290/0x290
[ 97.044824][ T822] ? mark_held_locks+0xb7/0x120
[ 97.045712][ T822] ? lockdep_hardirqs_on_prepare+0x12c/0x3e0
[ 97.046824][ T822] ? __local_bh_enable_ip+0xa5/0xf0
[ 97.047771][ T822] ? ___neigh_create+0x12a8/0x1eb0
[ 97.048710][ T822] ? trace_hardirqs_on+0x41/0x120
[ 97.049626][ T822] ? ___neigh_create+0x12a8/0x1eb0
[ 97.050556][ T822] ? __local_bh_enable_ip+0xa5/0xf0
[ 97.051509][ T822] ? ___neigh_create+0x12a8/0x1eb0
[ 97.052443][ T822] ? check_chain_key+0x244/0x5f0
[ 97.053352][ T822] ? rcu_read_lock_bh_held+0x56/0xa0
[ 97.054317][ T822] ? ip_finish_output2+0x6ea/0x2020
[ 97.055263][ T822] ? pneigh_lookup+0x410/0x410
[ 97.056135][ T822] ip_finish_output2+0x6ea/0x2020
[ ... ]
Acked-by: Guillaume Nault <gnault@redhat.com>
Fixes: 571912c69f ("net: UDP tunnel encapsulation module for tunnelling different protocols like MPLS, IP, NSH etc.")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Link: https://lore.kernel.org/r/20201228152136.24215-1-ap420073@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1fef73597f ]
ppp_cp_event is called directly or indirectly by ppp_rx with "ppp->lock"
held. It may call mod_timer to add a new timer. However, at the same time
ppp_timer may be already running and waiting for "ppp->lock". In this
case, there's no need for ppp_timer to continue running and it can just
exit.
If we let ppp_timer continue running, it may call add_timer. This causes
kernel panic because add_timer can't be called with a timer pending.
This patch fixes this problem.
Fixes: e022c2f07a ("WAN: new synchronous PPP implementation for generic HDLC.")
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5ede3ada3d ]
The function skb_copy() could return NULL, the return value
need to be checked.
Fixes: b5996f11ea ("net: add Hisilicon Network Subsystem basic ethernet support")
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 21fdca22eb ]
RT_TOS() only clears one of the ECN bits. Therefore, when
fib_compute_spec_dst() resorts to a fib lookup, it can return
different results depending on the value of the second ECN bit.
For example, ECT(0) and ECT(1) packets could be treated differently.
$ ip netns add ns0
$ ip netns add ns1
$ ip link add name veth01 netns ns0 type veth peer name veth10 netns ns1
$ ip -netns ns0 link set dev lo up
$ ip -netns ns1 link set dev lo up
$ ip -netns ns0 link set dev veth01 up
$ ip -netns ns1 link set dev veth10 up
$ ip -netns ns0 address add 192.0.2.10/24 dev veth01
$ ip -netns ns1 address add 192.0.2.11/24 dev veth10
$ ip -netns ns1 address add 192.0.2.21/32 dev lo
$ ip -netns ns1 route add 192.0.2.10/32 tos 4 dev veth10 src 192.0.2.21
$ ip netns exec ns1 sysctl -wq net.ipv4.icmp_echo_ignore_broadcasts=0
With TOS 4 and ECT(1), ns1 replies using source address 192.0.2.21
(ping uses -Q to set all TOS and ECN bits):
$ ip netns exec ns0 ping -c 1 -b -Q 5 192.0.2.255
[...]
64 bytes from 192.0.2.21: icmp_seq=1 ttl=64 time=0.544 ms
But with TOS 4 and ECT(0), ns1 replies using source address 192.0.2.11
because the "tos 4" route isn't matched:
$ ip netns exec ns0 ping -c 1 -b -Q 6 192.0.2.255
[...]
64 bytes from 192.0.2.11: icmp_seq=1 ttl=64 time=0.597 ms
After this patch the ECN bits don't affect the result anymore:
$ ip netns exec ns0 ping -c 1 -b -Q 6 192.0.2.255
[...]
64 bytes from 192.0.2.21: icmp_seq=1 ttl=64 time=0.591 ms
Fixes: 35ebf65e85 ("ipv4: Create and use fib_compute_spec_dst() helper.")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fb1e6e562b ]
A recent change skips sending firmware messages to the firmware when
pci_channel_offline() is true during fatal AER error. To make this
complete, we need to move the re-initialization sequence to
bnxt_io_resume(), otherwise the firmware messages to re-initialize
will all be skipped. In any case, it is more correct to re-initialize
in bnxt_io_resume().
Also, fix the reverse x-mas tree format when defining variables
in bnxt_io_slot_reset().
Fixes: b340dc680e ("bnxt_en: Avoid sending firmware messages when AER error is detected.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a029a2fef5 ]
TQM rings are hardware resources that require host context memory
managed by the driver. The driver supports up to 9 TQM rings and
the number of rings to use is requested by firmware during run-time.
Cap this number to the maximum supported to prevent accessing beyond
the array. Future firmware may request more than 9 TQM rings. Define
macros to remove the magic number 9 from the C code.
Fixes: ac3158cb01 ("bnxt_en: Allocate TQM ring context memory according to fw specification.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3c98cbf22a ]
This flag can be used by an end user to disable S0ix flows on a
buggy system or by an OEM for development purposes.
If you need this flag to be persisted across reboots, it's suggested
to use a udev rule to call adjust it until the kernel could have your
configuration in a disallow list.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Yijun Shen <Yijun.shen@dell.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6cecf02e77 ]
commit e086ba2fcc ("e1000e: disable s0ix entry and exit flows for ME
systems") disabled s0ix flows for systems that have various incarnations of
the i219-LM ethernet controller. This changed caused power consumption
regressions on the following shipping Dell Comet Lake based laptops:
* Latitude 5310
* Latitude 5410
* Latitude 5410
* Latitude 5510
* Precision 3550
* Latitude 5411
* Latitude 5511
* Precision 3551
* Precision 7550
* Precision 7750
This commit was introduced because of some regressions on certain Thinkpad
laptops. This comment was potentially caused by an earlier
commit 632fbd5eb5 ("e1000e: fix S0ix flows for cable connected case").
or it was possibly caused by a system not meeting platform architectural
requirements for low power consumption. Other changes made in the driver
with extended timeouts are expected to make the driver more impervious to
platform firmware behavior.
Fixes: e086ba2fcc ("e1000e: disable s0ix entry and exit flows for ME systems")
Reviewed-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Yijun Shen <Yijun.shen@dell.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 950271d7cc ]
Currently the tun_napi_alloc_frags() function returns -ENOMEM when the
number of iovs exceeds MAX_SKB_FRAGS + 1. However this is inappropriate,
we should use -EMSGSIZE instead of -ENOMEM.
The following distinctions are matters:
1. the caller need to drop the bad packet when -EMSGSIZE is returned,
which means meeting a persistent failure.
2. the caller can try again when -ENOMEM is returned, which means
meeting a transient failure.
Fixes: 90e33d4594 ("tun: enable napi_gro_frags() for TUN/TAP driver")
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://lore.kernel.org/r/1608864736-24332-1-git-send-email-wangyunjian@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4614792eeb ]
The CPTS driver registers PTP PHC clock when first netif is going up and
unregister it when all netif are down. Now ethtool will show:
- PTP PHC clock index 0 after boot until first netif is up;
- the last assigned PTP PHC clock index even if PTP PHC clock is not
registered any more after all netifs are down.
This patch ensures that -1 is returned by ethtool when PTP PHC clock is not
registered any more.
Fixes: 8a2c9a5ab4 ("net: ethernet: ti: cpts: rework initialization/deinitialization")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/20201224162405.28032-1-grygorii.strashko@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4ae2bb8164 ]
Accesses to dev->xps_rxqs_map (when using dev->num_tc) should be
protected by the rtnl lock, like we do for netif_set_xps_queue. I didn't
see an actual bug being triggered, but let's be safe here and take the
rtnl lock while accessing the map in sysfs.
Fixes: 8af2c06ff4 ("net-sysfs: Add interface for Rx queue(s) map per Tx queue")
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2d57b4f142 ]
Two race conditions can be triggered when storing xps rxqs, resulting in
various oops and invalid memory accesses:
1. Calling netdev_set_num_tc while netif_set_xps_queue:
- netif_set_xps_queue uses dev->tc_num as one of the parameters to
compute the size of new_dev_maps when allocating it. dev->tc_num is
also used to access the map, and the compiler may generate code to
retrieve this field multiple times in the function.
- netdev_set_num_tc sets dev->tc_num.
If new_dev_maps is allocated using dev->tc_num and then dev->tc_num
is set to a higher value through netdev_set_num_tc, later accesses to
new_dev_maps in netif_set_xps_queue could lead to accessing memory
outside of new_dev_maps; triggering an oops.
2. Calling netif_set_xps_queue while netdev_set_num_tc is running:
2.1. netdev_set_num_tc starts by resetting the xps queues,
dev->tc_num isn't updated yet.
2.2. netif_set_xps_queue is called, setting up the map with the
*old* dev->num_tc.
2.3. netdev_set_num_tc updates dev->tc_num.
2.4. Later accesses to the map lead to out of bound accesses and
oops.
A similar issue can be found with netdev_reset_tc.
One way of triggering this is to set an iface up (for which the driver
uses netdev_set_num_tc in the open path, such as bnx2x) and writing to
xps_rxqs in a concurrent thread. With the right timing an oops is
triggered.
Both issues have the same fix: netif_set_xps_queue, netdev_set_num_tc
and netdev_reset_tc should be mutually exclusive. We do that by taking
the rtnl lock in xps_rxqs_store.
Fixes: 8af2c06ff4 ("net-sysfs: Add interface for Rx queue(s) map per Tx queue")
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fb25038586 ]
Accesses to dev->xps_cpus_map (when using dev->num_tc) should be
protected by the rtnl lock, like we do for netif_set_xps_queue. I didn't
see an actual bug being triggered, but let's be safe here and take the
rtnl lock while accessing the map in sysfs.
Fixes: 184c449f91 ("net: Add support for XPS with QoS via traffic classes")
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1ad58225db ]
Two race conditions can be triggered when storing xps cpus, resulting in
various oops and invalid memory accesses:
1. Calling netdev_set_num_tc while netif_set_xps_queue:
- netif_set_xps_queue uses dev->tc_num as one of the parameters to
compute the size of new_dev_maps when allocating it. dev->tc_num is
also used to access the map, and the compiler may generate code to
retrieve this field multiple times in the function.
- netdev_set_num_tc sets dev->tc_num.
If new_dev_maps is allocated using dev->tc_num and then dev->tc_num
is set to a higher value through netdev_set_num_tc, later accesses to
new_dev_maps in netif_set_xps_queue could lead to accessing memory
outside of new_dev_maps; triggering an oops.
2. Calling netif_set_xps_queue while netdev_set_num_tc is running:
2.1. netdev_set_num_tc starts by resetting the xps queues,
dev->tc_num isn't updated yet.
2.2. netif_set_xps_queue is called, setting up the map with the
*old* dev->num_tc.
2.3. netdev_set_num_tc updates dev->tc_num.
2.4. Later accesses to the map lead to out of bound accesses and
oops.
A similar issue can be found with netdev_reset_tc.
One way of triggering this is to set an iface up (for which the driver
uses netdev_set_num_tc in the open path, such as bnx2x) and writing to
xps_cpus in a concurrent thread. With the right timing an oops is
triggered.
Both issues have the same fix: netif_set_xps_queue, netdev_set_num_tc
and netdev_reset_tc should be mutually exclusive. We do that by taking
the rtnl lock in xps_cpus_store.
Fixes: 184c449f91 ("net: Add support for XPS with QoS via traffic classes")
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit de33212f76 ]
virtnet_set_channels can recursively call cpus_read_lock if CONFIG_XPS
and CONFIG_HOTPLUG are enabled.
The path is:
virtnet_set_channels - calls get_online_cpus(), which is a trivial
wrapper around cpus_read_lock()
netif_set_real_num_tx_queues
netif_reset_xps_queues_gt
netif_reset_xps_queues - calls cpus_read_lock()
This call chain and potential deadlock happens when the number of TX
queues is reduced.
This commit the removes netif_set_real_num_[tr]x_queues calls from
inside the get/put_online_cpus section, as they don't require that it
be held.
Fixes: 47be24796c ("virtio-net: fix the set affinity bug when CPU IDs are not consecutive")
Signed-off-by: Jeff Dike <jdike@akamai.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://lore.kernel.org/r/20201223025421.671-1-jdike@akamai.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1f45dc2206 ]
Commit f9c6cea0b3 ("ibmvnic: Skip fatal error reset after passive init")
says "If the passive
CRQ initialization occurs before the FATAL reset task is processed,
the FATAL error reset task would try to access a CRQ message queue
that was freed, causing an oops. The problem may be most likely to
occur during DLPAR add vNIC with a non-default MTU, because the DLPAR
process will automatically issue a change MTU request.
Fix this by not processing fatal error reset if CRQ is passively
initialized after client-driven CRQ initialization fails."
Even with this commit, we still see similar kernel crashes. In order
to completely solve this problem, we'd better continue the fatal error
reset, capture the kernel crash, and try to fix it from that end.
Fixes: f9c6cea0b3 ("ibmvnic: Skip fatal error reset after passive init")
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Link: https://lore.kernel.org/r/20201219214034.21123-1-ljp@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a0c8be56af ]
Commit 34f0f4e3f4 ("ibmvnic: Fix login buffer memory leaks") frees
login_rsp_buffer in release_resources() and send_login()
because handle_login_rsp() does not free it.
Commit f3ae59c0c0 ("ibmvnic: store RX and TX subCRQ handle array in
ibmvnic_adapter struct") frees login_rsp_buffer in handle_login_rsp().
It seems unnecessary to free it in release_resources() and send_login().
There are chances that handle_login_rsp returns earlier without freeing
buffers. Double-checking the buffer is harmless since
release_login_buffer and release_login_rsp_buffer will
do nothing if buffer is already freed.
Fixes: f3ae59c0c0 ("ibmvnic: store RX and TX subCRQ handle array in ibmvnic_adapter struct")
Fixes: 34f0f4e3f4 ("ibmvnic: Fix login buffer memory leaks")
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Link: https://lore.kernel.org/r/20201219213919.21045-1-ljp@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f87777a3c3 ]
The dwmac glue registers on Amlogic Meson8b and newer SoCs has two clock
inputs:
- Meson8b and Meson8m2: MPLL2 and MPLL2 (the same parent is wired to
both inputs)
- GXBB, GXL, GXM, AXG, G12A, G12B, SM1: FCLK_DIV2 and MPLL2
All known vendor kernels and u-boots are using the first input only. We
let the common clock framework automatically choose the "right" parent.
For some boards this causes a problem though, specificially with G12A and
newer SoCs. The clock input is used for generating the 125MHz RGMII TX
clock. For the two input clocks this means on G12A:
- FCLK_DIV2: 999999985Hz / 8 = 124999998.125Hz
- MPLL2: 499999993Hz / 4 = 124999998.25Hz
In theory MPLL2 is the "better" clock input because it's gets us 0.125Hz
closer to the requested frequency than FCLK_DIV2. In reality however
there is a resource conflict because MPLL2 is needed to generate some of
the audio clocks. dwmac-meson8b probes first and sets up the clock tree
with MPLL2. This works fine until the audio driver comes and "steals"
the MPLL2 clocks and configures it with it's own rate (294909637Hz). The
common clock framework happily changes the MPLL2 rate but does not
reconfigure our RGMII TX clock tree, which then ends up at 73727409Hz,
which is more than 40% off the requested 125MHz.
Don't use the second clock input for now to force the common clock
framework to always select the first parent. This mimics the behavior
from the vendor driver and fixes the clock resource conflict with the
audio driver on G12A boards. Once the common clock framework can handle
this situation this change can be reverted again.
Fixes: 566e825162 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC")
Reported-by: Thomas Graichen <thomas.graichen@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: thomas graichen <thomas.graichen@gmail.com>
Link: https://lore.kernel.org/r/20201219135036.3216017-1-martin.blumenstingl@googlemail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1385ae5c30 ]
All the buffers and registers are already set up appropriately for an
MTU slightly above 1500, so we just need to expose this to the
networking stack. AFAICT, there's no need to implement .ndo_change_mtu
when the receive buffers are always set up to support the max_mtu.
This fixes several warnings during boot on our mpc8309-board with an
embedded mv88e6250 switch:
mv88e6085 mdio@e0102120:10: nonfatal error -34 setting MTU 1500 on port 0
...
mv88e6085 mdio@e0102120:10: nonfatal error -34 setting MTU 1500 on port 4
ucc_geth e0102000.ethernet eth1: error -22 setting MTU to 1504 to include DSA overhead
The last line explains what the DSA stack tries to do: achieving an MTU
of 1500 on-the-wire requires that the master netdevice connected to
the CPU port supports an MTU of 1500+the tagging overhead.
Fixes: bfcb813203 ("net: dsa: configure the MTU for switch ports")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e925e0cd2a ]
ugeth is the netdiv_priv() part of the netdevice. Accessing the memory
pointed to by ugeth (such as done by ucc_geth_memclean() and the two
of_node_puts) after free_netdev() is thus use-after-free.
Fixes: 80a9fad8e8 ("ucc_geth: fix module removal")
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3f48fab62b ]
Issue:
Flow control frame used to pause GoP(MAC) was delivered to the CPU
and created a load on the CPU. Since XOFF/XON frames are used only
by MAC, these frames should be dropped inside MAC.
Fix:
According to 802.3-2012 - IEEE Standard for Ethernet pause frame
has unique destination MAC address 01-80-C2-00-00-01.
Add TCAM parser entry to track and drop pause frames by destination MAC.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Link: https://lore.kernel.org/r/1608229817-21951-1-git-send-email-stefanc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3ac874fa84 ]
When removing VFs for PF added to bridge there was
an error I40E_AQ_RC_EINVAL. It was caused by not properly
resetting and reinitializing PF when adding/removing VFs.
Changed how reset is performed when adding/removing VFs
to properly reinitialize PFs VSI.
Fixes: fc60861e9b ("i40e: start up in VEPA mode by default")
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 31784cff7e ]
In preparation for converting exec_update_mutex to a rwsem so that
multiple readers can execute in parallel and not deadlock, add
down_read_interruptible. This is needed for perf_event_open to be
converted (with no semantic changes) from working on a mutex to
wroking on a rwsem.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/87k0tybqfy.fsf@x220.int.ebiederm.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f9368b5bf ]
In preparation for converting exec_update_mutex to a rwsem so that
multiple readers can execute in parallel and not deadlock, add
down_read_killable_nested. This is needed so that kcmp_lock
can be converted from working on a mutexes to working on rw_semaphores.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/87o8jabqh3.fsf@x220.int.ebiederm.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78af4dc949 ]
Syzbot reported a lock inversion involving perf. The sore point being
perf holding exec_update_mutex() for a very long time, specifically
across a whole bunch of filesystem ops in pmu::event_init() (uprobes)
and anon_inode_getfile().
This then inverts against procfs code trying to take
exec_update_mutex.
Move the permission checks later, such that we need to hold the mutex
over less code.
Reported-by: syzbot+db9cdf3dd1f64252c6ef@syzkaller.appspotmail.com
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d069dbe8a ]
Jan Kara's analysis of the syzbot report (edited):
The reproducer opens a directory on FUSE filesystem, it then attaches
dnotify mark to the open directory. After that a fuse_do_getattr() call
finds that attributes returned by the server are inconsistent, and calls
make_bad_inode() which, among other things does:
inode->i_mode = S_IFREG;
This then confuses dnotify which doesn't tear down its structures
properly and eventually crashes.
Avoid calling make_bad_inode() on a live inode: switch to a private flag on
the fuse inode. Also add the test to ops which the bad_inode_ops would
have caught.
This bug goes back to the initial merge of fuse in 2.6.14...
Reported-by: syzbot+f427adf9324b92652ccc@syzkaller.appspotmail.com
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Tested-by: Jan Kara <jack@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9d2e9ae95 ]
This moves siw and rxe to be virtual devices in the device tree:
lrwxrwxrwx 1 root root 0 Nov 6 13:55 /sys/class/infiniband/rxe0 -> ../../devices/virtual/infiniband/rxe0/
Previously they were trying to parent themselves to the physical device of
their attached netdev, which doesn't make alot of sense.
My hope is this will solve some weird syzkaller hits related to sysfs as
it could be possible that the parent of a netdev is another netdev, eg
under bonding or some other syzkaller found netdev configuration.
Nesting a ib_device under anything but a physical device is going to cause
inconsistencies in sysfs during destructions.
Link: https://lore.kernel.org/r/0-v1-dcbfc68c4b4a+d6-virtual_dev_jgg@nvidia.com
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a7a9e038b ]
Use the ib_dma_* helpers to skip the DMA translation instead. This
removes the last user if dma_virt_ops and keeps the weird layering
violation inside the RDMA core instead of burderning the DMA mapping
subsystems with it. This also means the software RDMA drivers now don't
have to mess with DMA parameters that are not relevant to them at all, and
that in the future we can use PCI P2P transfers even for software RDMA, as
there is no first fake layer of DMA mapping that the P2P DMA support.
Link: https://lore.kernel.org/r/20201106181941.1878556-8-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd14bf0e4a ]
UFS 3.1 specification mentions that the WriteBooster flags listed below
will be set to their default values, i.e. disabled, after power cycle or
any type of reset event. Thus we need to reset the flag variables kept in
struct hba to align with the device status and ensure that
WriteBooster-related functions are configured properly after device reset.
Without this fix, WriteBooster will not be enabled successfully after by
ufshcd_wb_ctrl() after device reset because hba->wb_enabled remains true.
Flags required to be reset to default values:
- fWriteBoosterEn: hba->wb_enabled
- fWriteBoosterBufferFlushEn: hba->wb_buf_flush_enabled
- fWriteBoosterBufferFlushDuringHibernate: No variable mapped
Link: https://lore.kernel.org/r/20201208135635.15326-2-stanley.chu@mediatek.com
Fixes: 3d17b9b5ab ("scsi: ufs: Add write booster feature support")
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0e2497e334 upstream.
Apply Display WA #22010492432 for combo PHY PLLs too. This should fix a
problem where the PLL output frequency is slightly off with the current
PLL fractional divider value.
I haven't seen an actual case where this causes a problem, but let's
follow the spec. It's also needed on some EHL platforms, but for that we
also need a way to distinguish the affected EHL SKUs, so I leave that
for a follow-up.
v2:
- Apply the WA at one place when calculating the PLL dividers from the
frequency and the frequency from the dividers for all the combo PLL
use cases (DP, HDMI, TBT). (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201003001846.1271151-6-imre.deak@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a31489d2a3 upstream.
During controller initialization, an LE Set RPA Timeout command is sent
to the controller if supported. However, the value checked to determine
if the command is supported is incorrect. Page 1921 of the Bluetooth
Core Spec v5.2 shows that bit 2 of octet 35 of the Supported_Commands
field corresponds to the LE Set RPA Timeout command, but currently
bit 6 of octet 35 is checked. This patch checks the correct value
instead.
This issue led to the error seen in the following btmon output during
initialization of an adapter (rtl8761b) and prevented initialization
from completing.
< HCI Command: LE Set Resolvable Private Address Timeout (0x08|0x002e) plen 2
Timeout: 900 seconds
> HCI Event: Command Complete (0x0e) plen 4
LE Set Resolvable Private Address Timeout (0x08|0x002e) ncmd 2
Status: Unsupported Remote Feature / Unsupported LMP Feature (0x1a)
= Close Index: 00:E0:4C:6B:E5:03
The error did not appear when running with this patch.
Signed-off-by: Edward Vear <edwardvear@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts stable commit baad618d07.
This commit is adding lines to spinand_write_to_cache_op, wheras the upstream
commit 868cbe2a6d that this was supposed to
backport was touching spinand_read_from_cache_op.
It causes a crash on writing OOB data by attempting to write to read-only
kernel memory.
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 82ef1370b0 ]
Commit cfd7323772 ("ext4: add prefetching for block allocation
bitmaps") introduced block bitmap prefetch, and expects to read block
bitmaps of flex_bg through an IO. However, it seems to ignore the
value range of s_log_groups_per_flex. In the scenario where the value
of s_log_groups_per_flex is greater than 27, s_mb_prefetch or
s_mb_prefetch_limit will overflow, cause a divide zero exception.
In addition, the logic of calculating nr is also flawed, because the
size of flexbg is fixed during a single mount, but s_mb_prefetch can
be modified, which causes nr to fail to meet the value condition of
[1, flexbg_size].
To solve this problem, we need to set the upper limit of
s_mb_prefetch. Since we expect to load block bitmaps of a flex_bg
through an IO, we can consider determining a reasonable upper limit
among the IO limit parameters. After consideration, we chose
BLK_MAX_SEGMENT_SIZE. This is a good choice to solve divide zero
problem and avoiding performance degradation.
[ Some minor code simplifications to make the changes easy to follow -- TYT ]
Reported-by: Tosk Robot <tencent_os_robot@tencent.com>
Signed-off-by: Chunguang Xu <brookxu@tencent.com>
Reviewed-by: Samuel Liao <samuelliao@tencent.com>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Link: https://lore.kernel.org/r/1607051143-24508-1-git-send-email-brookxu@tencent.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 252bd12563 ]
If emergency system shutdown is called, like by thermal shutdown,
a dm device could be alive when the block device couldn't process
I/O requests anymore. In this state, the handling of I/O errors
by new dm I/O requests or by those already in-flight can lead to
a verity corruption state, which is a misjudgment.
So, skip verity work in response to I/O error when system is shutting
down.
Signed-off-by: Hyeongseok Kim <hyeongseok@gmail.com>
Reviewed-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 618de0f4ef ]
The PCM hw_params core function tries to clear up the PCM buffer
before actually using for avoiding the information leak from the
previous usages or the usage before a new allocation. It performs the
memset() with runtime->dma_bytes, but this might still leave some
remaining bytes untouched; namely, the PCM buffer size is aligned in
page size for mmap, hence runtime->dma_bytes doesn't necessarily cover
all PCM buffer pages, and the remaining bytes are exposed via mmap.
This patch changes the memory clearance to cover the all buffer pages
if the stream is supposed to be mmap-ready (that guarantees that the
buffer size is aligned in page size).
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20201218145625.2045-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9cd2be519d ]
list_empty_careful() is not racy only if some conditions are met, i.e.
no re-adds after del_init. io_cqring_overflow_flush() does list_move(),
so it's actually racy.
Remove those checks, we have ->cq_check_overflow for the fast path.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9365965db0 ]
Clear the kernel stack backchain before potentially calling the
lockdep trace_hardirqs_off/on functions. Without this walking the
kernel backchain, e.g. during a panic, might stop too early.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ba8ea8e7dd ]
can_stop_idle_tick() checks whether the do_timer() duty has been taken over
by a CPU on boot. That's silly because the boot CPU always takes over with
the initial clockevent device.
But even if no CPU would have installed a clockevent and taken over the
duty then the question whether the tick on the current CPU can be stopped
or not is moot. In that case the current CPU would have no clockevent
either, so there would be nothing to keep ticking.
Remove it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/20201206212002.725238293@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 503b934a75 ]
Expanding the READ_PLUS extents can cause the read buffer to overflow.
If it does, then don't error, but just exit early.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc6b6a872d ]
Internally, UBD treats each physical IO segment as a separate command to
be submitted in the execution pipe. If the pipe returns a transient
error after a few segments have already been written, UBD will tell the
block layer to requeue the request, but there is no way to reclaim the
segments already submitted. When a new attempt to dispatch the request
is done, those segments already submitted will get duplicated, causing
the WARN_ON below in the best case, and potentially data corruption.
In my system, running a UML instance with 2GB of RAM and a 50M UBD disk,
I can reproduce the WARN_ON by simply running mkfs.fvat against the
disk on a freshly booted system.
There are a few ways to around this, like reducing the pressure on
the pipe by reducing the queue depth, which almost eliminates the
occurrence of the problem, increasing the pipe buffer size on the host
system, or by limiting the request to one physical segment, which causes
the block layer to submit way more requests to resolve a single
operation.
Instead, this patch modifies the format of a UBD command, such that all
segments are sent through a single element in the communication pipe,
turning the command submission atomic from the point of view of the
block layer. The new format has a variable size, depending on the
number of elements, and looks like this:
+------------+-----------+-----------+------------
| cmd_header | segment 0 | segment 1 | segment ...
+------------+-----------+-----------+------------
With this format, we push a pointer to cmd_header in the submission
pipe.
This has the advantage of reducing the memory footprint of executing a
single request, since it allow us to merge some fields in the header.
It is possible to reduce even further each segment memory footprint, by
merging bitmap_words and cow_offset, for instance, but this is not the
focus of this patch and is left as future work. One issue with the
patch is that for a big number of segments, we now perform one big
memory allocation instead of multiple small ones, but I wasn't able to
trigger any real issues or -ENOMEM because of this change, that wouldn't
be reproduced otherwise.
This was tested using fio with the verify-crc32 option, and by running
an ext4 filesystem over this UBD device.
The original WARN_ON was:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at lib/refcount.c:28 refcount_warn_saturate+0x13f/0x141
refcount_t: underflow; use-after-free.
Modules linked in:
CPU: 0 PID: 0 Comm: swapper Not tainted 5.5.0-rc6-00002-g2a5bb2cf75c8 #346
Stack:
6084eed0 6063dc77 00000009 6084ef60
00000000 604b8d9f 6084eee0 6063dcbc
6084ef40 6006ab8d e013d780 1c00000000
Call Trace:
[<600a0c1c>] ? printk+0x0/0x94
[<6004a888>] show_stack+0x13b/0x155
[<6063dc77>] ? dump_stack_print_info+0xdf/0xe8
[<604b8d9f>] ? refcount_warn_saturate+0x13f/0x141
[<6063dcbc>] dump_stack+0x2a/0x2c
[<6006ab8d>] __warn+0x107/0x134
[<6008da6c>] ? wake_up_process+0x17/0x19
[<60487628>] ? blk_queue_max_discard_sectors+0x0/0xd
[<6006b05f>] warn_slowpath_fmt+0xd1/0xdf
[<6006af8e>] ? warn_slowpath_fmt+0x0/0xdf
[<600acc14>] ? raw_read_seqcount_begin.constprop.0+0x0/0x15
[<600619ae>] ? os_nsecs+0x1d/0x2b
[<604b8d9f>] refcount_warn_saturate+0x13f/0x141
[<6048bc8f>] refcount_sub_and_test.constprop.0+0x2f/0x37
[<6048c8de>] blk_mq_free_request+0xf1/0x10d
[<6048ca06>] __blk_mq_end_request+0x10c/0x114
[<6005ac0f>] ubd_intr+0xb5/0x169
[<600a1a37>] __handle_irq_event_percpu+0x6b/0x17e
[<600a1b70>] handle_irq_event_percpu+0x26/0x69
[<600a1bd9>] handle_irq_event+0x26/0x34
[<600a1bb3>] ? handle_irq_event+0x0/0x34
[<600a5186>] ? unmask_irq+0x0/0x37
[<600a57e6>] handle_edge_irq+0xbc/0xd6
[<600a131a>] generic_handle_irq+0x21/0x29
[<60048f6e>] do_IRQ+0x39/0x54
[...]
---[ end trace c6e7444e55386c0f ]---
Cc: Christopher Obbard <chris.obbard@collabora.com>
Reported-by: Martyn Welch <martyn@collabora.com>
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.com>
Tested-by: Christopher Obbard <chris.obbard@collabora.com>
Acked-by: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 72d3e093af ]
The UML random driver creates a dummy device under the guest,
/dev/hw_random. When this file is read from the guest, the driver
reads from the host machine's /dev/random, in-turn reading from
the host kernel's entropy pool. This entropy pool could have been
filled by a hardware random number generator or just the host
kernel's internal software entropy generator.
Currently the driver does not fill the guests kernel entropy pool,
this requires a userspace tool running inside the guest (like
rng-tools) to read from the dummy device provided by this driver,
which then would fill the guest's internal entropy pool.
This all seems quite pointless when we are already reading from an
entropy pool, so this patch aims to register the device as a hwrng
device using the hwrng-core framework. This not only improves and
cleans up the driver, but also fills the guest's entropy pool
without having to resort to using extra userspace tools in the guest.
This is typically a nuisance when booting a guest: the random pool
takes a long time (~200s) to build up enough entropy since the dummy
hwrng is not used to fill the guest's pool.
This port was originally attempted by Alexander Neville "dark" (in CC,
discussion in Link), but the conversation there stalled since the
handling of -EAGAIN errors were no removed and longer handled by the
driver. This patch attempts to use the existing method of error
handling but utilises the new hwrng core.
The issue can be noticed when booting a UML guest:
[ 2.560000] random: fast init done
[ 214.000000] random: crng init done
With the patch applied, filling the pool becomes a lot quicker:
[ 2.560000] random: fast init done
[ 12.000000] random: crng init done
Cc: Alexander Neville <dark@volatile.bz>
Link: https://lore.kernel.org/lkml/20190828204609.02a7ff70@TheDarkness/
Link: https://lore.kernel.org/lkml/20190829135001.6a5ff940@TheDarkness.local/
Cc: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
Acked-by: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit edf7ddbf1c ]
Missing calls to mntget() (or equivalently, too many calls to mntput())
are hard to detect because mntput() delays freeing mounts using
task_work_add(), then again using call_rcu(). As a result, mnt_count
can often be decremented to -1 without getting a KASAN use-after-free
report. Such cases are still bugs though, and they point to real
use-after-frees being possible.
For an example of this, see the bug fixed by commit 1b0b9cc8d3
("vfs: fsmount: add missing mntget()"), discussed at
https://lkml.kernel.org/linux-fsdevel/20190605135401.GB30925@xxxxxxxxxxxxxxxxxxxxxxxxx/T/#u.
This bug *should* have been trivial to find. But actually, it wasn't
found until syzkaller happened to use fchdir() to manipulate the
reference count just right for the bug to be noticeable.
Address this by making mntput_no_expire() issue a WARN if mnt_count has
become negative.
Suggested-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59d512e437 ]
This is way to catch some cases of decrementer overflow, when the
decrementer has underflowed an odd number of times, while MSR[EE] was
disabled.
With a typical small decrementer, a timer that fires when MSR[EE] is
disabled will be "lost" if MSR[EE] remains disabled for between 4.3 and
8.6 seconds after the timer expires. In any case, the decrementer
interrupt would be taken at 8.6 seconds and the timer would be found at
that point.
So this check is for catching extreme latency events, and it prevents
those latencies from being a further few seconds long. It's not obvious
this is a good tradeoff. This is already a watchdog magnitude event and
that situation is not improved a significantly with this check. For
large decrementers, it's useless.
Therefore remove this check, which avoids a mftb when enabling hard
disabled interrupts (e.g., when enabling after coming from hardware
interrupt handlers). Perhaps more importantly, it also removes the
clunky MSR[EE] vs PACA_IRQ_HARD_DIS incoherency in soft-interrupt replay
which simplifies the code.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201107014336.2337337-1-npiggin@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 38dc717e97 ]
Apparently there has been a longstanding race between udev/systemd and
the module loader. Currently, the module loader sends a uevent right
after sysfs initialization, but before the module calls its init
function. However, some udev rules expect that the module has
initialized already upon receiving the uevent.
This race has been triggered recently (see link in references) in some
systemd mount unit files. For instance, the configfs module creates the
/sys/kernel/config mount point in its init function, however the module
loader issues the uevent before this happens. sys-kernel-config.mount
expects to be able to mount /sys/kernel/config upon receipt of the
module loading uevent, but if the configfs module has not called its
init function yet, then this directory will not exist and the mount unit
fails. A similar situation exists for sys-fs-fuse-connections.mount, as
the fuse sysfs mount point is created during the fuse module's init
function. If udev is faster than module initialization then the mount
unit would fail in a similar fashion.
To fix this race, delay the module KOBJ_ADD uevent until after the
module has finished calling its init routine.
References: https://github.com/systemd/systemd/issues/17586
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-By: Nicolas Morey-Chaisemartin <nmoreychaisemartin@suse.com>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6d49ecd10 ]
When returning the layout in nfs4_evict_inode(), we need to ensure that
the layout is actually done being freed before we can proceed to free the
inode itself.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 10f04d40a9 ]
The on-disk quota format supports quota files with upto 2^32 blocks. Be
careful when computing quota file offsets in the quota files from block
numbers as they can overflow 32-bit types. Since quota files larger than
4GB would require ~26 millions of quota users, this is mostly a
theoretical concern now but better be careful, fuzzers would find the
problem sooner or later anyway...
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5e8ed280da ]
If a module fails to load due to an error in prepare_coming_module(),
the following error handling in load_module() runs with
MODULE_STATE_COMING in module's state. Fix it by correctly setting
MODULE_STATE_GOING under "bug_cleanup" label.
Signed-off-by: Miroslav Benes <mbenes@suse.cz>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 65b2b21348 upstream.
syzbot reports following issue:
INFO: task syz-executor.2:12399 can't die for more than 143 seconds.
task:syz-executor.2 state:D stack:28744 pid:12399 ppid: 8504 flags:0x00004004
Call Trace:
context_switch kernel/sched/core.c:3773 [inline]
__schedule+0x893/0x2170 kernel/sched/core.c:4522
schedule+0xcf/0x270 kernel/sched/core.c:4600
schedule_timeout+0x1d8/0x250 kernel/time/timer.c:1847
do_wait_for_common kernel/sched/completion.c:85 [inline]
__wait_for_common kernel/sched/completion.c:106 [inline]
wait_for_common kernel/sched/completion.c:117 [inline]
wait_for_completion+0x163/0x260 kernel/sched/completion.c:138
kthread_stop+0x17a/0x720 kernel/kthread.c:596
io_put_sq_data fs/io_uring.c:7193 [inline]
io_sq_thread_stop+0x452/0x570 fs/io_uring.c:7290
io_finish_async fs/io_uring.c:7297 [inline]
io_sq_offload_create fs/io_uring.c:8015 [inline]
io_uring_create fs/io_uring.c:9433 [inline]
io_uring_setup+0x19b7/0x3730 fs/io_uring.c:9507
do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x45deb9
Code: Unable to access opcode bytes at RIP 0x45de8f.
RSP: 002b:00007f174e51ac78 EFLAGS: 00000246 ORIG_RAX: 00000000000001a9
RAX: ffffffffffffffda RBX: 0000000000008640 RCX: 000000000045deb9
RDX: 0000000000000000 RSI: 0000000020000140 RDI: 00000000000050e5
RBP: 000000000118bf58 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 000000000118bf2c
R13: 00007ffed9ca723f R14: 00007f174e51b9c0 R15: 000000000118bf2c
INFO: task syz-executor.2:12399 blocked for more than 143 seconds.
Not tainted 5.10.0-rc3-next-20201110-syzkaller #0
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
Currently we don't have a reproducer yet, but seems that there is a
race in current codes:
=> io_put_sq_data
ctx_list is empty now. |
==> kthread_park(sqd->thread); |
| T1: sq thread is parked now.
==> kthread_stop(sqd->thread); |
KTHREAD_SHOULD_STOP is set now.|
===> kthread_unpark(k); |
| T2: sq thread is now unparkd, run again.
|
| T3: sq thread is now preempted out.
|
===> wake_up_process(k); |
|
| T4: Since sqd ctx_list is empty, needs_sched will be true,
| then sq thread sets task state to TASK_INTERRUPTIBLE,
| and schedule, now sq thread will never be waken up.
===> wait_for_completion |
I have artificially used mdelay() to simulate above race, will get same
stack like this syzbot report, but to be honest, I'm not sure this code
race triggers syzbot report.
To fix this possible code race, when sq thread is unparked, need to check
whether sq thread has been stopped.
Reported-by: syzbot+03beeb595f074db9cfd1@syzkaller.appspotmail.com
Signed-off-by: Xiaoguang Wang <xiaoguang.wang@linux.alibaba.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d1ddb5e79 upstream.
Syzbot reports a potential deadlock found by the newly added recursive
read deadlock detection in lockdep:
[...] ========================================================
[...] WARNING: possible irq lock inversion dependency detected
[...] 5.9.0-rc2-syzkaller #0 Not tainted
[...] --------------------------------------------------------
[...] syz-executor.1/10214 just changed the state of lock:
[...] ffff88811f506338 (&f->f_owner.lock){.+..}-{2:2}, at: send_sigurg+0x1d/0x200
[...] but this lock was taken by another, HARDIRQ-safe lock in the past:
[...] (&dev->event_lock){-...}-{2:2}
[...]
[...]
[...] and interrupts could create inverse lock ordering between them.
[...]
[...]
[...] other info that might help us debug this:
[...] Chain exists of:
[...] &dev->event_lock --> &new->fa_lock --> &f->f_owner.lock
[...]
[...] Possible interrupt unsafe locking scenario:
[...]
[...] CPU0 CPU1
[...] ---- ----
[...] lock(&f->f_owner.lock);
[...] local_irq_disable();
[...] lock(&dev->event_lock);
[...] lock(&new->fa_lock);
[...] <Interrupt>
[...] lock(&dev->event_lock);
[...]
[...] *** DEADLOCK ***
The corresponding deadlock case is as followed:
CPU 0 CPU 1 CPU 2
read_lock(&fown->lock);
spin_lock_irqsave(&dev->event_lock, ...)
write_lock_irq(&filp->f_owner.lock); // wait for the lock
read_lock(&fown-lock); // have to wait until the writer release
// due to the fairness
<interrupted>
spin_lock_irqsave(&dev->event_lock); // wait for the lock
The lock dependency on CPU 1 happens if there exists a call sequence:
input_inject_event():
spin_lock_irqsave(&dev->event_lock,...);
input_handle_event():
input_pass_values():
input_to_handler():
handler->event(): // evdev_event()
evdev_pass_values():
spin_lock(&client->buffer_lock);
__pass_event():
kill_fasync():
kill_fasync_rcu():
read_lock(&fa->fa_lock);
send_sigio():
read_lock(&fown->lock);
To fix this, make the reader in send_sigurg() and send_sigio() use
read_lock_irqsave() and read_lock_irqrestore().
Reported-by: syzbot+22e87cdf94021b984aa6@syzkaller.appspotmail.com
Reported-by: syzbot+c5e32344981ad9f33750@syzkaller.appspotmail.com
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c9200760da upstream.
Check for valid block size directly by validating s_log_block_size; we
were doing this in two places. First, by calculating blocksize via
BLOCK_SIZE << s_log_block_size, and then checking that the blocksize
was valid. And then secondly, by checking s_log_block_size directly.
The first check is not reliable, and can trigger an UBSAN warning if
s_log_block_size on a maliciously corrupted superblock is greater than
22. This is harmless, since the second test will correctly reject the
maliciously fuzzed file system, but to make syzbot shut up, and
because the two checks are duplicative in any case, delete the
blocksize check, and move the s_log_block_size earlier in
ext4_fill_super().
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reported-by: syzbot+345b75652b1d24227443@syzkaller.appspotmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4ebd470370 upstream.
The snd_seq_queue struct contains various flags in the bit fields.
Those are categorized to two different use cases, both of which are
protected by different spinlocks. That implies that there are still
potential risks of the bad operations for bit fields by concurrent
accesses.
For addressing the problem, this patch rearranges those flags to be
a standard bool instead of a bit field.
Reported-by: syzbot+63cbe31877bb80ef58f5@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/20201206083456.21110-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 39aead8373 upstream.
So ever since syzbot discovered fbcon, we have solid proof that it's
full of bugs. And often the solution is to just delete code and remove
features, e.g. 50145474f6 ("fbcon: remove soft scrollback code").
Now the problem is that most modern-ish drivers really only treat
fbcon as an dumb kernel console until userspace takes over, and Oops
printer for some emergencies. Looking at drm drivers and the basic
vesa/efi fbdev drivers shows that only 3 drivers support any kind of
acceleration:
- nouveau, seems to be enabled by default
- omapdrm, when a DMM remapper exists using remapper rewriting for
y/xpanning
- gma500, but that is getting deleted now for the GTT remapper trick,
and the accelerated copyarea never set the FBINFO_HWACCEL_COPYAREA
flag, so unused (and could be deleted already I think).
No other driver supportes accelerated fbcon. And fbcon is the only
user of this accel code (it's not exposed as uapi through ioctls),
which means we could garbage collect fairly enormous amounts of code
if we kill this.
Plus because syzbot only runs on virtual hardware, and none of the
drivers for that have acceleration, we'd remove a huge gap in testing.
And there's no other even remotely comprehensive testing aside from
syzbot.
This patch here just disables the acceleration code by always
redrawing when scrolling. The plan is that once this has been merged
for well over a year in released kernels, we can start to go around
and delete a lot of code.
v2:
- Drop a few more unused local variables, somehow I missed the
compiler warnings (Sam)
- Fix typo in comment (Jiri)
- add a todo entry for the cleanup (Thomas)
v3: Remove more unused variables (0day)
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: nouveau@lists.freedesktop.org
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Peilin Ye <yepeilin.cs@gmail.com>
Cc: George Kennedy <george.kennedy@oracle.com>
Cc: Nathan Chancellor <natechancellor@gmail.com>
Cc: Peter Rosin <peda@axentia.se>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201029132229.4068359-1-daniel.vetter@ffwll.ch
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ddcdea5b5 upstream.
To pick up the changes in:
a85cbe6159 ("uapi: move constants from <linux/kernel.h> to <linux/const.h>")
That causes no changes in tooling, just addresses this perf build
warning:
Warning: Kernel ABI header at 'tools/include/uapi/linux/const.h' differs from latest version at 'include/uapi/linux/const.h'
diff -u tools/include/uapi/linux/const.h include/uapi/linux/const.h
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Petr Vorel <petr.vorel@gmail.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a85cbe6159 upstream.
and include <linux/const.h> in UAPI headers instead of <linux/kernel.h>.
The reason is to avoid indirect <linux/sysinfo.h> include when using
some network headers: <linux/netlink.h> or others -> <linux/kernel.h>
-> <linux/sysinfo.h>.
This indirect include causes on MUSL redefinition of struct sysinfo when
included both <sys/sysinfo.h> and some of UAPI headers:
In file included from x86_64-buildroot-linux-musl/sysroot/usr/include/linux/kernel.h:5,
from x86_64-buildroot-linux-musl/sysroot/usr/include/linux/netlink.h:5,
from ../include/tst_netlink.h:14,
from tst_crypto.c:13:
x86_64-buildroot-linux-musl/sysroot/usr/include/linux/sysinfo.h:8:8: error: redefinition of `struct sysinfo'
struct sysinfo {
^~~~~~~
In file included from ../include/tst_safe_macros.h:15,
from ../include/tst_test.h:93,
from tst_crypto.c:11:
x86_64-buildroot-linux-musl/sysroot/usr/include/sys/sysinfo.h:10:8: note: originally defined here
Link: https://lkml.kernel.org/r/20201015190013.8901-1-petr.vorel@gmail.com
Signed-off-by: Petr Vorel <petr.vorel@gmail.com>
Suggested-by: Rich Felker <dalias@aerifal.cx>
Acked-by: Rich Felker <dalias@libc.org>
Cc: Peter Korsgaard <peter@korsgaard.com>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Florian Weimer <fweimer@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ffc54220c upstream.
io_sqe_files_unregister() uninterruptibly waits for enqueued ref nodes,
however requests keeping them may never complete, e.g. because of some
userspace dependency. Make sure it's interruptible otherwise it would
hang forever.
Cc: stable@vger.kernel.org # 5.6+
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 77788775c7 upstream.
If we COW the identity, we assume that ->mm never changes. But this
isn't true of multiple processes end up sharing the ring. Hence treat
id->mm like like any other process compontent when it comes to the
identity mapping. This is pretty trivial, just moving the existing grab
into io_grab_identity(), and including a check for the match.
Cc: stable@vger.kernel.org # 5.10
Fixes: 1e6fa5216a ("io_uring: COW io_identity on mismatch")
Reported-by: Christian Brauner <christian.brauner@ubuntu.com>:
Tested-by: Christian Brauner <christian.brauner@ubuntu.com>:
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f0bb29e8c4 upstream.
Decompressing zlib streams on s390 fails with "incorrect data check"
error.
Userspace zlib checks inflate_state.flags in order to byteswap checksums
only for zlib streams, and s390 hardware inflate code, which was ported
from there, tries to match this behavior. At the same time, kernel zlib
does not use inflate_state.flags, so it contains essentially random
values. For many use cases either zlib stream is zeroed out or checksum
is not used, so this problem is masked, but at least SquashFS is still
affected.
Fix by always passing a checksum to and from the hardware as is, which
matches zlib_inflate()'s expectations.
Link: https://lkml.kernel.org/r/20201215155551.894884-1-iii@linux.ibm.com
Fixes: 1261961000 ("lib/zlib: add s390 hardware support for kernel zlib_inflate")
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Mikhail Zaslonko <zaslonko@linux.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Mikhail Zaslonko <zaslonko@linux.ibm.com>
Cc: <stable@vger.kernel.org> [5.6+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc2da7b45f upstream.
VMware observed a performance regression during memmap init on their
platform, and bisected to commit 73a6e474cb ("mm: memmap_init:
iterate over memblock regions rather that check each PFN") causing it.
Before the commit:
[0.033176] Normal zone: 1445888 pages used for memmap
[0.033176] Normal zone: 89391104 pages, LIFO batch:63
[0.035851] ACPI: PM-Timer IO Port: 0x448
With commit
[0.026874] Normal zone: 1445888 pages used for memmap
[0.026875] Normal zone: 89391104 pages, LIFO batch:63
[2.028450] ACPI: PM-Timer IO Port: 0x448
The root cause is the current memmap defer init doesn't work as expected.
Before, memmap_init_zone() was used to do memmap init of one whole zone,
to initialize all low zones of one numa node, but defer memmap init of
the last zone in that numa node. However, since commit 73a6e474cb,
function memmap_init() is adapted to iterater over memblock regions
inside one zone, then call memmap_init_zone() to do memmap init for each
region.
E.g, on VMware's system, the memory layout is as below, there are two
memory regions in node 2. The current code will mistakenly initialize the
whole 1st region [mem 0xab00000000-0xfcffffffff], then do memmap defer to
iniatialize only one memmory section on the 2nd region [mem
0x10000000000-0x1033fffffff]. In fact, we only expect to see that there's
only one memory section's memmap initialized. That's why more time is
costed at the time.
[ 0.008842] ACPI: SRAT: Node 0 PXM 0 [mem 0x00000000-0x0009ffff]
[ 0.008842] ACPI: SRAT: Node 0 PXM 0 [mem 0x00100000-0xbfffffff]
[ 0.008843] ACPI: SRAT: Node 0 PXM 0 [mem 0x100000000-0x55ffffffff]
[ 0.008844] ACPI: SRAT: Node 1 PXM 1 [mem 0x5600000000-0xaaffffffff]
[ 0.008844] ACPI: SRAT: Node 2 PXM 2 [mem 0xab00000000-0xfcffffffff]
[ 0.008845] ACPI: SRAT: Node 2 PXM 2 [mem 0x10000000000-0x1033fffffff]
Now, let's add a parameter 'zone_end_pfn' to memmap_init_zone() to pass
down the real zone end pfn so that defer_init() can use it to judge
whether defer need be taken in zone wide.
Link: https://lkml.kernel.org/r/20201223080811.16211-1-bhe@redhat.com
Link: https://lkml.kernel.org/r/20201223080811.16211-2-bhe@redhat.com
Fixes: commit 73a6e474cb ("mm: memmap_init: iterate over memblock regions rather that check each PFN")
Signed-off-by: Baoquan He <bhe@redhat.com>
Reported-by: Rahul Gopakumar <gopakumarr@vmware.com>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7dd91c456 upstream.
syzbot reported the deadlock here [1]. The issue is in hugetlb cow
error handling when there are not enough huge pages for the faulting
task which took the original reservation. It is possible that other
(child) tasks could have consumed pages associated with the reservation.
In this case, we want the task which took the original reservation to
succeed. So, we unmap any associated pages in children so that they can
be used by the faulting task that owns the reservation.
The unmapping code needs to hold i_mmap_rwsem in write mode. However,
due to commit c0d0381ade ("hugetlbfs: use i_mmap_rwsem for more pmd
sharing synchronization") we are already holding i_mmap_rwsem in read
mode when hugetlb_cow is called.
Technically, i_mmap_rwsem does not need to be held in read mode for COW
mappings as they can not share pmd's. Modifying the fault code to not
take i_mmap_rwsem in read mode for COW (and other non-sharable) mappings
is too involved for a stable fix.
Instead, we simply drop the hugetlb_fault_mutex and i_mmap_rwsem before
unmapping. This is OK as it is technically not needed. They are
reacquired after unmapping as expected by calling code. Since this is
done in an uncommon error path, the overhead of dropping and reacquiring
mutexes is acceptable.
While making changes, remove redundant BUG_ON after unmap_ref_private.
[1] https://lkml.kernel.org/r/000000000000b73ccc05b5cf8558@google.com
Link: https://lkml.kernel.org/r/4c5781b8-3b00-761e-c0c7-c5edebb6ec1a@oracle.com
Fixes: c0d0381ade ("hugetlbfs: use i_mmap_rwsem for more pmd sharing synchronization")
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Reported-by: syzbot+5eee4145df3c15e96625@syzkaller.appspotmail.com
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: "Aneesh Kumar K . V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cd3ed3c73a ]
Set rp_size to zero will be ignore during remounting.
The method to identify whether we input a remounting option of
rp_size is to check if the rp_size input is zero. It can not work
well if we pass "rp_size=0".
This patch add a bool variable "set_rp_size" to fix this problem.
Reported-by: Jubin Zhong <zhongjubin@huawei.com>
Signed-off-by: lizhe <lizhe67@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit dfea9fce29 upstream.
The purpose of io_uring_cancel_files() is to wait for all requests
matching ->files to go/be cancelled. We should first drop files of a
request in io_req_drop_files() and only then make it undiscoverable for
io_uring_cancel_files.
First drop, then delete from list. It's ok to leave req->id->files
dangling, because it's not dereferenced by cancellation code, only
compared against. It would potentially go to sleep and be awaken by
following in io_req_drop_files() wake_up().
Fixes: 0f2122045b ("io_uring: don't rely on weak ->files references")
Cc: <stable@vger.kernel.org> # 5.5+
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 93decc5636 upstream.
In __make_request() a new r10bio is allocated and passed to
raid10_read_request(). The read_slot member of the bio is not
initialized, and the raid10_read_request() uses it to index an
array. This leads to occasional panics.
Fix by initializing the field to invalid value and checking for
valid value in raid10_read_request().
Cc: stable@vger.kernel.org
Signed-off-by: Kevin Vigor <kvigor@gmail.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0c14846032 ]
Currently MPTCP is not propagating the security context
from the ingress request socket to newly created msk
at clone time.
Address the issue invoking the missing security helper.
Fixes: cf7da0d66c ("mptcp: Create SUBFLOW socket for incoming connections")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 028c221ed1 ]
AMD systems provide a "NodeId" value that represents a global ID
indicating to which "Node" a logical CPU belongs. The "Node" is a
physical structure equivalent to a Die, and it should not be confused
with logical structures like NUMA nodes. Logical nodes can be adjusted
based on firmware or other settings whereas the physical nodes/dies are
fixed based on hardware topology.
The NodeId value can be used when a physical ID is needed by software.
Save the AMD NodeId to struct cpuinfo_x86.cpu_die_id. Use the value
from CPUID or MSR as appropriate. Default to phys_proc_id otherwise.
Do so for both AMD and Hygon systems.
Drop the node_id parameter from cacheinfo_*_init_llc_id() as it is no
longer needed.
Update the x86 topology documentation.
Suggested-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20201109210659.754018-2-Yazen.Ghannam@amd.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d652d5f1ee upstream.
Commit 991fcb77f4 ("drm/edid: Fix uninitialized variable in
drm_cvt_modes()") just replaced one warning with another.
The original warning about a possibly uninitialized variable was due to
the compiler not being smart enough to see that the case statement
actually enumerated all possible cases. And the initial fix was just to
add a "default" case that had a single "unreachable()", just to tell the
compiler that that situation cannot happen.
However, that doesn't actually fix the fundamental reason for the
problem: the compiler still doesn't see that the existing case
statements enumerate all possibilities, so the compiler will still
generate code to jump to that unreachable case statement. It just won't
complain about an uninitialized variable any more.
So now the compiler generates code to our inline asm marker that we told
it would not fall through, and end end result is basically random. We
have created a bridge to nowhere.
And then, depending on the random details of just exactly what the
compiler ends up doing, 'objtool' might end up complaining about the
conditional branches (for conditions that cannot happen, and that thus
will never be taken - but if the compiler was not smart enough to figure
that out, we can't expect objtool to do so) going off in the weeds.
So depending on how the compiler has laid out the result, you might see
something like this:
drivers/gpu/drm/drm_edid.o: warning: objtool: do_cvt_mode() falls through to next function drm_mode_detailed.isra.0()
and now you have a truly inscrutable warning that makes no sense at all
unless you start looking at whatever random code the compiler happened
to generate for our bare "unreachable()" statement.
IOW, don't use "unreachable()" unless you have an _active_ operation
that generates code that actually makes it obvious that something is not
reachable (ie an UD instruction or similar).
Solve the "compiler isn't smart enough" problem by just marking one of
the cases as "default", so that even when the compiler doesn't otherwise
see that we've enumerated all cases, the compiler will feel happy and
safe about there always being a valid case that initializes the 'width'
variable.
This also generates better code, since now the compiler doesn't generate
comparisons for five different possibilities (the four real ones and the
one that can't happen), but just for the three real ones and "the rest"
(which is that last one).
A smart enough compiler that sees that we cover all the cases won't care.
Cc: Lyude Paul <lyude@redhat.com>
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0ebcdd702f upstream.
For a null_blk device with zoned mode enabled is currently initialized
with a number of zones equal to the device capacity divided by the zone
size, without considering if the device capacity is a multiple of the
zone size. If the zone size is not a divisor of the capacity, the zones
end up not covering the entire capacity, potentially resulting is out
of bounds accesses to the zone array.
Fix this by adding one last smaller zone with a size equal to the
remainder of the disk capacity divided by the zone size if the capacity
is not a multiple of the zone size. For such smaller last zone, the zone
capacity is also checked so that it does not exceed the smaller zone
size.
Reported-by: Naohiro Aota <naohiro.aota@wdc.com>
Fixes: ca4b2a0119 ("null_blk: add zone support")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit adab66b71a upstream.
It was believed that metag was the only architecture that required the ring
buffer to keep 8 byte words aligned on 8 byte architectures, and with its
removal, it was assumed that the ring buffer code did not need to handle
this case. It appears that sparc64 also requires this.
The following was reported on a sparc64 boot up:
kernel: futex hash table entries: 65536 (order: 9, 4194304 bytes, linear)
kernel: Running postponed tracer tests:
kernel: Testing tracer function:
kernel: Kernel unaligned access at TPC[552a20] trace_function+0x40/0x140
kernel: Kernel unaligned access at TPC[552a24] trace_function+0x44/0x140
kernel: Kernel unaligned access at TPC[552a20] trace_function+0x40/0x140
kernel: Kernel unaligned access at TPC[552a24] trace_function+0x44/0x140
kernel: Kernel unaligned access at TPC[552a20] trace_function+0x40/0x140
kernel: PASSED
Need to put back the 64BIT aligned code for the ring buffer.
Link: https://lore.kernel.org/r/CADxRZqzXQRYgKc=y-KV=S_yHL+Y8Ay2mh5ezeZUnpRvg+syWKw@mail.gmail.com
Cc: stable@vger.kernel.org
Fixes: 86b3de60a0 ("ring-buffer: Remove HAVE_64BIT_ALIGNED_ACCESS")
Reported-by: Anatoly Pugachev <matorola@gmail.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 138a6428ba upstream.
The reliance on the remoteproc's state for determining when to send
sysmon notifications to a remote processor is racy with regard to
concurrent remoteproc operations.
Further more the advertisement of the state of other remote processor to
a newly started remote processor might not only send the wrong state,
but might result in a stream of state changes that are out of order.
Address this by introducing state tracking within the sysmon instances
themselves and extend the locking to ensure that the notifications are
consistent with this state.
Fixes: 1f36ab3f6e ("remoteproc: sysmon: Inform current rproc about all active rprocs")
Fixes: 1877f54f75 ("remoteproc: sysmon: Add notifications for events")
Fixes: 1fb82ee806 ("remoteproc: qcom: Introduce sysmon")
Cc: stable@vger.kernel.org
Reviewed-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Link: https://lore.kernel.org/r/20201122054135.802935-2-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 291de1d102 upstream.
When I use the axp20x chip to power my SDIO device on the 5.4 kernel,
the output voltage of DLDO2 is wrong. After comparing the register
manual and source code of the chip, I found that the mask bit of the
driver register of the port was wrong. I fixed this error by modifying
the mask register of the source code. This error seems to be a copy
error of the macro when writing the code. Now the voltage output of
the DLDO2 port of axp20x is correct. My development environment is
Allwinner A40I of arm architecture, and the kernel version is 5.4.
Signed-off-by: DingHua Ma <dinghua.ma.sz@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Cc: <stable@vger.kernel.org>
Fixes: db4a555f7c ("regulator: axp20x: use defines for masks")
Link: https://lore.kernel.org/r/20201201001000.22302-1-dinghua.ma.sz@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4684709bf8 upstream.
If kobject_init_and_add() fails, pci_slot_release() is called to delete
slot->list from parent->slots. But slot->list hasn't been initialized
yet, so we dereference a NULL pointer:
Unable to handle kernel NULL pointer dereference at virtual address
00000000
...
CPU: 10 PID: 1 Comm: swapper/0 Not tainted 4.4.240 #197
task: ffffeb398a45ef10 task.stack: ffffeb398a470000
PC is at __list_del_entry_valid+0x5c/0xb0
LR is at pci_slot_release+0x84/0xe4
...
__list_del_entry_valid+0x5c/0xb0
pci_slot_release+0x84/0xe4
kobject_put+0x184/0x1c4
pci_create_slot+0x17c/0x1b4
__pci_hp_initialize+0x68/0xa4
pciehp_probe+0x1a4/0x2fc
pcie_port_probe_service+0x58/0x84
driver_probe_device+0x320/0x470
Initialize slot->list before calling kobject_init_and_add() to avoid this.
Fixes: 8a94644b44 ("PCI: Fix pci_create_slot() reference count leak")
Link: https://lore.kernel.org/r/1606876422-117457-1-git-send-email-zhongjubin@huawei.com
Signed-off-by: Jubin Zhong <zhongjubin@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v5.9+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5812b32e01 upstream.
Specify type alignment when declaring linker-section match-table entries
to prevent gcc from increasing alignment and corrupting the various
tables with padding (e.g. timers, irqchips, clocks, reserved memory).
This is specifically needed on x86 where gcc (typically) aligns larger
objects like struct of_device_id with static extent on 32-byte
boundaries which at best prevents matching on anything but the first
entry. Specifying alignment when declaring variables suppresses this
optimisation.
Here's a 64-bit example where all entries are corrupt as 16 bytes of
padding has been inserted before the first entry:
ffffffff8266b4b0 D __clk_of_table
ffffffff8266b4c0 d __of_table_fixed_factor_clk
ffffffff8266b5a0 d __of_table_fixed_clk
ffffffff8266b680 d __clk_of_table_sentinel
And here's a 32-bit example where the 8-byte-aligned table happens to be
placed on a 32-byte boundary so that all but the first entry are corrupt
due to the 28 bytes of padding inserted between entries:
812b3ec0 D __irqchip_of_table
812b3ec0 d __of_table_irqchip1
812b3fa0 d __of_table_irqchip2
812b4080 d __of_table_irqchip3
812b4160 d irqchip_of_match_end
Verified on x86 using gcc-9.3 and gcc-4.9 (which uses 64-byte
alignment), and on arm using gcc-7.2.
Note that there are no in-tree users of these tables on x86 currently
(even if they are included in the image).
Fixes: 54196ccbe0 ("of: consolidate linker section OF match table declarations")
Fixes: f6e916b820 ("irqchip: add basic infrastructure")
Cc: stable <stable@vger.kernel.org> # 3.9
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20201123102319.8090-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ed89b89330 upstream.
It was accidentally dropped while adding multiple wiphy support
Fixes fast-rx support and avoids handling reordering in both mac80211
and the driver
Cc: stable@vger.kernel.org
Fixes: c89d362541 ("mt76: add function for allocating an extra wiphy")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe60009903 upstream.
This 2-in-1 model (Product name: Switch SA5-271) features a SW_TABLET_MODE
that works as it would be expected, both when detaching the keyboard and
when folding it behind the tablet body.
It used to work until the introduction of the allow list at
commit 8169bd3e6e ("platform/x86: intel-vbtn: Switch to an allow-list
for SW_TABLET_MODE reporting"). Add this model to it, so that the Virtual
Buttons device announces the EV_SW features again.
Fixes: 8169bd3e6e ("platform/x86: intel-vbtn: Switch to an allow-list for SW_TABLET_MODE reporting")
Cc: stable@vger.kernel.org
Signed-off-by: Carlos Garnacho <carlosg@gnome.org>
Link: https://lore.kernel.org/r/20201201135727.212917-1-carlosg@gnome.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2dd2a1740e upstream.
A recent change to ndctl to attempt to reconfigure namespaces in place
uncovered a label accounting problem in block-window-type namespaces.
The ndctl "create.sh" test is able to trigger this signature:
WARNING: CPU: 34 PID: 9167 at drivers/nvdimm/label.c:1100 __blk_label_update+0x9a3/0xbc0 [libnvdimm]
[..]
RIP: 0010:__blk_label_update+0x9a3/0xbc0 [libnvdimm]
[..]
Call Trace:
uuid_store+0x21b/0x2f0 [libnvdimm]
kernfs_fop_write+0xcf/0x1c0
vfs_write+0xcc/0x380
ksys_write+0x68/0xe0
When allocated capacity for a namespace is renamed (new UUID) the labels
with the old UUID need to be deleted. The ndctl behavior to always
destroy namespaces on reconfiguration hid this problem.
The immediate impact of this bug is limited since block-window-type
namespaces only seem to exist in the specification and not in any
shipping products. However, the label handling code is being reused for
other technologies like CXL region labels, so there is a benefit to
making sure both vertical labels sets (block-window) and horizontal
label sets (pmem) have a functional reference implementation in
libnvdimm.
Fixes: c4703ce11c ("libnvdimm/namespace: Fix label tracking error")
Cc: <stable@vger.kernel.org>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9996bd4947 upstream.
'xenbus_backend' watches 'state' of devices, which is writable by
guests. Hence, if guests intensively updates it, dom0 will have lots of
pending events that exhausting memory of dom0. In other words, guests
can trigger dom0 memory pressure. This is known as XSA-349. However,
the watch callback of it, 'frontend_changed()', reads only 'state', so
doesn't need to have the pending events.
To avoid the problem, this commit disallows pending watch messages for
'xenbus_backend' using the 'will_handle()' watch callback.
This is part of XSA-349
Cc: stable@vger.kernel.org
Signed-off-by: SeongJae Park <sjpark@amazon.de>
Reported-by: Michael Kurth <mku@amazon.de>
Reported-by: Pawel Wieczorkiewicz <wipawel@amazon.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3dc86ca6b4 upstream.
This commit adds a counter of pending messages for each watch in the
struct. It is used to skip unnecessary pending messages lookup in
'unregister_xenbus_watch()'. It could also be used in 'will_handle'
callback.
This is part of XSA-349
Cc: stable@vger.kernel.org
Signed-off-by: SeongJae Park <sjpark@amazon.de>
Reported-by: Michael Kurth <mku@amazon.de>
Reported-by: Pawel Wieczorkiewicz <wipawel@amazon.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e85d32b1c upstream.
Some code does not directly make 'xenbus_watch' object and call
'register_xenbus_watch()' but use 'xenbus_watch_path()' instead. This
commit adds support of 'will_handle' callback in the
'xenbus_watch_path()' and it's wrapper, 'xenbus_watch_pathfmt()'.
This is part of XSA-349
Cc: stable@vger.kernel.org
Signed-off-by: SeongJae Park <sjpark@amazon.de>
Reported-by: Michael Kurth <mku@amazon.de>
Reported-by: Pawel Wieczorkiewicz <wipawel@amazon.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fed1755b11 upstream.
If handling logics of watch events are slower than the events enqueue
logic and the events can be created from the guests, the guests could
trigger memory pressure by intensively inducing the events, because it
will create a huge number of pending events that exhausting the memory.
Fortunately, some watch events could be ignored, depending on its
handler callback. For example, if the callback has interest in only one
single path, the watch wouldn't want multiple pending events. Or, some
watches could ignore events to same path.
To let such watches to volutarily help avoiding the memory pressure
situation, this commit introduces new watch callback, 'will_handle'. If
it is not NULL, it will be called for each new event just before
enqueuing it. Then, if the callback returns false, the event will be
discarded. No watch is using the callback for now, though.
This is part of XSA-349
Cc: stable@vger.kernel.org
Signed-off-by: SeongJae Park <sjpark@amazon.de>
Reported-by: Michael Kurth <mku@amazon.de>
Reported-by: Pawel Wieczorkiewicz <wipawel@amazon.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c728719a4 upstream.
When xen_blkif_disconnect() is called, the kernel thread behind the
block interface is stopped by calling kthread_stop(ring->xenblkd).
The ring->xenblkd thread pointer being non-NULL determines if the
thread has been already stopped.
Normally, the thread's function xen_blkif_schedule() sets the
ring->xenblkd to NULL, when the thread's main loop ends.
However, when the thread has not been started yet (i.e.
wake_up_process() has not been called on it), the xen_blkif_schedule()
function would not be called yet.
In such case the kthread_stop() call returns -EINTR and the
ring->xenblkd remains dangling.
When this happens, any consecutive call to xen_blkif_disconnect (for
example in frontend_changed() callback) leads to a kernel crash in
kthread_stop() (e.g. NULL pointer dereference in exit_creds()).
This is XSA-350.
Cc: <stable@vger.kernel.org> # 4.12
Fixes: a24fa22ce2 ("xen/blkback: don't use xen_blkif_get() in xen-blkback kthread")
Reported-by: Olivier Benjamin <oliben@amazon.com>
Reported-by: Pawel Wieczorkiewicz <wipawel@amazon.de>
Signed-off-by: Pawel Wieczorkiewicz <wipawel@amazon.de>
Reviewed-by: Julien Grall <jgrall@amazon.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66482f6407 upstream.
The device_links_purge() function (called from device_del()) tries to
remove the links.needs_suppliers list entry, but it's using
list_del(), hence it doesn't initialize after the removal. This is OK
for normal cases where device_del() is called via device_destroy().
However, it's not guaranteed that the device object will be really
deleted soon after device_del(). In a minor case like HD-audio codec
reconfiguration that re-initializes the device after device_del(), it
may lead to a crash by the corrupted list entry.
As a simple fix, replace list_del() with list_del_init() in order to
make the list intact after the device_del() call.
Fixes: e2ae9bcc4a ("driver core: Add support for linking devices during device addition")
Cc: <stable@vger.kernel.org>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20201208190326.27531-1-tiwai@suse.de
Cc: Saravana Kannan <saravanak@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6160aca443 upstream.
Return values from read_dt_param() will be either TRUE (1) or
FALSE (0), while dfll_fetch_pwm_params() returns 0 on success
or an ERR code on failure.
So this patch fixes the bug of returning 0 on failure.
Fixes: 36541f0499 ("clk: tegra: dfll: support PWM regulator control")
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 11a163f2c7 upstream.
The previous code assumed that a higher hardware value always resulted
in a bigger divider, which is correct for the regular clocks, but is
an invalid assumption when a divider table is provided for the clock.
Perfect example of this is the PLL0_HALF clock, which applies a /2
divider with the hardware value 0, and a /1 divider otherwise.
Fixes: a9fa2893fc ("clk: ingenic: Add support for divider tables")
Cc: <stable@vger.kernel.org> # 5.2
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20201212135733.38050-1-paul@crapouillou.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bca5b06580 upstream.
md-cluster uses MD_CLUSTER_SEND_LOCK to make node can exclusively send msg.
During sending msg, node can concurrently receive msg from another node.
When node does resync job, grab token_lockres:EX may trigger a deadlock:
```
nodeA nodeB
-------------------- --------------------
a.
send METADATA_UPDATED
held token_lockres:EX
b.
md_do_sync
resync_info_update
send RESYNCING
+ set MD_CLUSTER_SEND_LOCK
+ wait for holding token_lockres:EX
c.
mdadm /dev/md0 --remove /dev/sdg
+ held reconfig_mutex
+ send REMOVE
+ wait_event(MD_CLUSTER_SEND_LOCK)
d.
recv_daemon //METADATA_UPDATED from A
process_metadata_update
+ (mddev_trylock(mddev) ||
MD_CLUSTER_HOLDING_MUTEX_FOR_RECVD)
//this time, both return false forever
```
Explaination:
a. A send METADATA_UPDATED
This will block another node to send msg
b. B does sync jobs, which will send RESYNCING at intervals.
This will be block for holding token_lockres:EX lock.
c. B do "mdadm --remove", which will send REMOVE.
This will be blocked by step <b>: MD_CLUSTER_SEND_LOCK is 1.
d. B recv METADATA_UPDATED msg, which send from A in step <a>.
This will be blocked by step <c>: holding mddev lock, it makes
wait_event can't hold mddev lock. (btw,
MD_CLUSTER_HOLDING_MUTEX_FOR_RECVD keep ZERO in this scenario.)
There is a similar deadlock in commit 0ba959774e
("md-cluster: use sync way to handle METADATA_UPDATED msg")
In that commit, step c is "update sb". This patch step c is
"mdadm --remove".
For fixing this issue, we can refer the solution of function:
metadata_update_start. Which does the same grab lock_token action.
lock_comm can use the same steps to avoid deadlock. By moving
MD_CLUSTER_HOLDING_MUTEX_FOR_RECVD from lock_token to lock_comm.
It enlarge a little bit window of MD_CLUSTER_HOLDING_MUTEX_FOR_RECVD,
but it is safe & can break deadlock.
Repro steps (I only triggered 3 times with hundreds tests):
two nodes share 3 iSCSI luns: sdg/sdh/sdi. Each lun size is 1GB.
```
ssh root@node2 "mdadm -S --scan"
mdadm -S --scan
for i in {g,h,i};do dd if=/dev/zero of=/dev/sd$i oflag=direct bs=1M \
count=20; done
mdadm -C /dev/md0 -b clustered -e 1.2 -n 2 -l mirror /dev/sdg /dev/sdh \
--bitmap-chunk=1M
ssh root@node2 "mdadm -A /dev/md0 /dev/sdg /dev/sdh"
sleep 5
mkfs.xfs /dev/md0
mdadm --manage --add /dev/md0 /dev/sdi
mdadm --wait /dev/md0
mdadm --grow --raid-devices=3 /dev/md0
mdadm /dev/md0 --fail /dev/sdg
mdadm /dev/md0 --remove /dev/sdg
mdadm --grow --raid-devices=2 /dev/md0
```
test script will hung when executing "mdadm --remove".
```
# dump stacks by "echo t > /proc/sysrq-trigger"
md0_cluster_rec D 0 5329 2 0x80004000
Call Trace:
__schedule+0x1f6/0x560
? _cond_resched+0x2d/0x40
? schedule+0x4a/0xb0
? process_metadata_update.isra.0+0xdb/0x140 [md_cluster]
? wait_woken+0x80/0x80
? process_recvd_msg+0x113/0x1d0 [md_cluster]
? recv_daemon+0x9e/0x120 [md_cluster]
? md_thread+0x94/0x160 [md_mod]
? wait_woken+0x80/0x80
? md_congested+0x30/0x30 [md_mod]
? kthread+0x115/0x140
? __kthread_bind_mask+0x60/0x60
? ret_from_fork+0x1f/0x40
mdadm D 0 5423 1 0x00004004
Call Trace:
__schedule+0x1f6/0x560
? __schedule+0x1fe/0x560
? schedule+0x4a/0xb0
? lock_comm.isra.0+0x7b/0xb0 [md_cluster]
? wait_woken+0x80/0x80
? remove_disk+0x4f/0x90 [md_cluster]
? hot_remove_disk+0xb1/0x1b0 [md_mod]
? md_ioctl+0x50c/0xba0 [md_mod]
? wait_woken+0x80/0x80
? blkdev_ioctl+0xa2/0x2a0
? block_ioctl+0x39/0x40
? ksys_ioctl+0x82/0xc0
? __x64_sys_ioctl+0x16/0x20
? do_syscall_64+0x5f/0x150
? entry_SYSCALL_64_after_hwframe+0x44/0xa9
md0_resync D 0 5425 2 0x80004000
Call Trace:
__schedule+0x1f6/0x560
? schedule+0x4a/0xb0
? dlm_lock_sync+0xa1/0xd0 [md_cluster]
? wait_woken+0x80/0x80
? lock_token+0x2d/0x90 [md_cluster]
? resync_info_update+0x95/0x100 [md_cluster]
? raid1_sync_request+0x7d3/0xa40 [raid1]
? md_do_sync.cold+0x737/0xc8f [md_mod]
? md_thread+0x94/0x160 [md_mod]
? md_congested+0x30/0x30 [md_mod]
? kthread+0x115/0x140
? __kthread_bind_mask+0x60/0x60
? ret_from_fork+0x1f/0x40
```
At last, thanks for Xiao's solution.
Cc: stable@vger.kernel.org
Signed-off-by: Zhao Heming <heming.zhao@suse.com>
Suggested-by: Xiao Ni <xni@redhat.com>
Reviewed-by: Xiao Ni <xni@redhat.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8da01f79c upstream.
Reshape request should be blocked with ongoing resync job. In cluster
env, a node can start resync job even if the resync cmd isn't executed
on it, e.g., user executes "mdadm --grow" on node A, sometimes node B
will start resync job. However, current update_raid_disks() only check
local recovery status, which is incomplete. As a result, we see user will
execute "mdadm --grow" successfully on local, while the remote node deny
to do reshape job when it doing resync job. The inconsistent handling
cause array enter unexpected status. If user doesn't observe this issue
and continue executing mdadm cmd, the array doesn't work at last.
Fix this issue by blocking reshape request. When node executes "--grow"
and detects ongoing resync, it should stop and report error to user.
The following script reproduces the issue with ~100% probability.
(two nodes share 3 iSCSI luns: sdg/sdh/sdi. Each lun size is 1GB)
```
# on node1, node2 is the remote node.
ssh root@node2 "mdadm -S --scan"
mdadm -S --scan
for i in {g,h,i};do dd if=/dev/zero of=/dev/sd$i oflag=direct bs=1M \
count=20; done
mdadm -C /dev/md0 -b clustered -e 1.2 -n 2 -l mirror /dev/sdg /dev/sdh
ssh root@node2 "mdadm -A /dev/md0 /dev/sdg /dev/sdh"
sleep 5
mdadm --manage --add /dev/md0 /dev/sdi
mdadm --wait /dev/md0
mdadm --grow --raid-devices=3 /dev/md0
mdadm /dev/md0 --fail /dev/sdg
mdadm /dev/md0 --remove /dev/sdg
mdadm --grow --raid-devices=2 /dev/md0
```
Cc: stable@vger.kernel.org
Signed-off-by: Zhao Heming <heming.zhao@suse.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1e405bc251 upstream.
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp() assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv() data with alignment
explicitly requested. This data is allocated with kzalloc() so no
data can leak apart from previous readings.
In this driver the timestamp can end up in various different locations
depending on what other channels are enabled. As a result, we don't
use a structure to specify it's position as that would be misleading.
Fixes: e717f8c6df ("iio: adc: Add the TI ads124s08 ADC code")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200920112742.170751-9-jic23@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b6b51234d upstream.
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable array in the iio_priv() data with alignment
explicitly requested. This data is allocated with kzalloc() so no
data can leak apart from previous readings.
In this driver, depending on which channels are enabled, the timestamp
can be in a number of locations. Hence we cannot use a structure
to specify the data layout without it being misleading.
Fixes: 77c4ad2d6a ("iio: imu: Add initial support for Bosch BMI160")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Cc: Daniel Baluta <daniel.baluta@oss.nxp.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200920112742.170751-6-jic23@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 198cf32f05 upstream.
Whilst this is another case of the issue Lars reported with
an array of elements of smaller than 8 bytes being passed
to iio_push_to_buffers_with_timestamp(), the solution here is
a bit different from the other cases and relies on __aligned
working on the stack (true since 4.6?)
This one is unusual. We have to do an explicit memset() each time
as we are reading 3 bytes into a potential 4 byte channel which
may sometimes be a 2 byte channel depending on what is enabled.
As such, moving the buffer to the heap in the iio_priv structure
doesn't save us much. We can't use a nice explicit structure
on the stack either as the data channels have different storage
sizes and are all separately controlled.
Fixes: cc26ad455f ("iio: Add Freescale MPL3115A2 pressure / temperature sensor driver")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200920112742.170751-7-jic23@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 89deb13342 upstream.
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp() assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv() data.
This data is allocated with kzalloc() so no data can leak apart from
previous readings.
The explicit alignment of ts is not necessary in this case but
does make the code slightly less fragile so I have included it.
Fixes: 39631b5f95 ("iio: Add Freescale mag3110 magnetometer driver")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200920112742.170751-4-jic23@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d837a996f5 upstream.
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp() assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv()
This data is allocated with kzalloc() so no data can leak apart
from previous readings.
A local unsigned int variable is used for the regmap call so it
is clear there is no potential issue with writing into the padding
of the structure.
Fixes: 3025c8688c ("iio: light: add support for UVIS25 sensor")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200920112742.170751-3-jic23@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a61817216b upstream.
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp() assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv().
This data is allocated with kzalloc() so no data can leak apart
from previous readings and in this case the status byte from the device.
The forced alignment of ts is not necessary in this case but it
potentially makes the code less fragile.
>From personal communications with Mikko:
We could probably split the reading of the int register, but it
would mean a significant performance cost of 20 i2c clock cycles.
Fixes: e12ffd241c ("iio: light: rpr0521 triggered buffer")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Mikko Koivunen <mikko.koivunen@fi.rohmeurope.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200920112742.170751-2-jic23@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f9bce7a22 upstream.
If we are using edge IRQs, new samples can arrive while processing
current interrupt since there are no hw guarantees the irq line
stays "low" long enough to properly detect the new interrupt.
In this case the new sample will be missed.
Polling FIFO status register in st_lsm6dsx_handler_thread routine
allow us to read new samples even if the interrupt arrives while
processing previous data and the timeslot where the line is "low"
is too short to be properly detected.
Fixes: 89ca88a7cd ("iio: imu: st_lsm6dsx: support active-low interrupts")
Fixes: 290a6ce11d ("iio: imu: add support to lsm6dsx driver")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/5e93cda7dc1e665f5685c53ad8e9ea71dbae782d.1605378871.git.lorenzo@kernel.org
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 19ef7b70ca upstream.
When updating the buffer demux, we will skip a scan element from the
device in the case `in_ind != out_ind` and we enter the while loop.
in_ind should only be refreshed with `find_next_bit()` in the end of the
loop.
Note, to cause problems we need a situation where we are skippig over
an element (channel not enabled) that happens to not have the same size
as the next element. Whilst this is a possible situation we haven't
actually identified any cases in mainline where it happens as most drivers
have consistent channel storage sizes with the exception of the timestamp
which is the last element and hence never skipped over.
Fixes: 5ada4ea9be ("staging:iio: add demux optionally to path from device to buffer")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20201112144323.28887-1-nuno.sa@analog.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 398840f8bb upstream.
This was an oversight in the original implementation, as it makes no
sense to specify both scoping flags to the same openat2(2) invocation
(before this patch, the result of such an invocation was equivalent to
RESOLVE_IN_ROOT being ignored).
This is a userspace-visible ABI change, but the only user of openat2(2)
at the moment is LXC which doesn't specify both flags and so no
userspace programs will break as a result.
Fixes: fddb5d430a ("open: introduce openat2(2) syscall")
Signed-off-by: Aleksa Sarai <cyphar@cyphar.com>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Cc: <stable@vger.kernel.org> # v5.6+
Link: https://lore.kernel.org/r/20201027235044.5240-2-cyphar@cyphar.com
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7dab164a9 upstream.
The following call trace was seen during HBA reset testing:
BUG: scheduling while atomic: swapper/2/0/0x10000100
...
Call Trace:
dump_stack+0x19/0x1b
__schedule_bug+0x64/0x72
__schedule+0x782/0x840
__cond_resched+0x26/0x30
_cond_resched+0x3a/0x50
mempool_alloc+0xa0/0x170
lpfc_unreg_rpi+0x151/0x630 [lpfc]
lpfc_sli_abts_recover_port+0x171/0x190 [lpfc]
lpfc_sli4_abts_err_handler+0xb2/0x1f0 [lpfc]
lpfc_sli4_io_xri_aborted+0x256/0x300 [lpfc]
lpfc_sli4_sp_handle_abort_xri_wcqe.isra.51+0xa3/0x190 [lpfc]
lpfc_sli4_fp_handle_cqe+0x89/0x4d0 [lpfc]
__lpfc_sli4_process_cq+0xdb/0x2e0 [lpfc]
__lpfc_sli4_hba_process_cq+0x41/0x100 [lpfc]
lpfc_cq_poll_hdler+0x1a/0x30 [lpfc]
irq_poll_softirq+0xc7/0x100
__do_softirq+0xf5/0x280
call_softirq+0x1c/0x30
do_softirq+0x65/0xa0
irq_exit+0x105/0x110
do_IRQ+0x56/0xf0
common_interrupt+0x16a/0x16a
With the conversion to blk_io_poll for better interrupt latency in normal
cases, it introduced this code path, executed when I/O aborts or logouts
are seen, which attempts to allocate memory for a mailbox command to be
issued. The allocation is GFP_KERNEL, thus it could attempt to sleep.
Fix by creating a work element that performs the event handling for the
remote port. This will have the mailbox commands and other items performed
in the work element, not the irq. A much better method as the "irq" routine
does not stall while performing all this deep handling code.
Ensure that allocation failures are handled and send LOGO on failure.
Additionally, enlarge the mailbox memory pool to reduce the possibility of
additional allocation in this path.
Link: https://lore.kernel.org/r/20201020202719.54726-3-james.smart@broadcom.com
Fixes: 317aeb83c9 ("scsi: lpfc: Add blk_io_poll support for latency improvment")
Cc: <stable@vger.kernel.org> # v5.9+
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 62e3a931db upstream.
The following calltrace was seen:
BUG: sleeping function called from invalid context at mm/slab.h:494
...
Call Trace:
dump_stack+0x9a/0xf0
___might_sleep.cold.63+0x13d/0x178
slab_pre_alloc_hook+0x6a/0x90
kmem_cache_alloc_trace+0x3a/0x2d0
lpfc_sli4_nvmet_alloc+0x4c/0x280 [lpfc]
lpfc_post_rq_buffer+0x2e7/0xa60 [lpfc]
lpfc_sli4_hba_setup+0x6b4c/0xa4b0 [lpfc]
lpfc_pci_probe_one_s4.isra.15+0x14f8/0x2280 [lpfc]
lpfc_pci_probe_one+0x260/0x2880 [lpfc]
local_pci_probe+0xd4/0x180
work_for_cpu_fn+0x51/0xa0
process_one_work+0x8f0/0x17b0
worker_thread+0x536/0xb50
kthread+0x30c/0x3d0
ret_from_fork+0x3a/0x50
A prior patch introduced a spin_lock_irqsave(hbalock) in the
lpfc_post_rq_buffer() routine. Call trace is seen as the hbalock is held
with interrupts disabled during a GFP_KERNEL allocation in
lpfc_sli4_nvmet_alloc().
Fix by reordering locking so that hbalock not held when calling
sli4_nvmet_alloc() (aka rqb_buf_list()).
Link: https://lore.kernel.org/r/20201020202719.54726-2-james.smart@broadcom.com
Fixes: 411de511c6 ("scsi: lpfc: Fix RQ empty firmware trap")
Cc: <stable@vger.kernel.org> # v4.17+
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 639a82434f upstream.
Some devices (especially QCA ones) are already using hardcoded partition
names with colons in it. The OpenMesh A62 for example provides following
mtd relevant information via cmdline:
root=31:11 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(custom),64k(0:KEYS),0x002b0000(kernel),0x00c80000(rootfs),15552k(inactive) rootfsname=rootfs rootwait
The change to split only on the last colon between mtd-id and partitions
will cause newpart to see following string for the first partition:
KEYS),0x002b0000(kernel),0x00c80000(rootfs),15552k(inactive)
Such a partition list cannot be parsed and thus the device fails to boot.
Avoid this behavior by making sure that the start of the first part-name
("(") will also be the last byte the mtd-id split algorithm is using for
its colon search.
Fixes: eb13fa0227 ("mtd: parser: cmdline: Support MTD names containing one or more colons")
Cc: stable@vger.kernel.org
Cc: Ron Minnich <rminnich@google.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201124062506.185392-1-sven@narfation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cac8c82105 upstream.
Following error was seen when mounting a 16MByte ubifs:
UBIFS error (ubi0:0 pid 1893): check_lpt_type.constprop.6: invalid type (15) in LPT node type
QSPI_IFR.TFRTYP was not set correctly. When data transfer is enabled
and one wants to access the serial memory through AHB in order to:
- read in the serial memory, but not a memory data, for example
a JEDEC-ID, QSPI_IFR.TFRTYP must be written to '0' (both sama5d2
and sam9x60).
- read in the serial memory, and particularly a memory data,
TFRTYP must be written to '1' (both sama5d2 and sam9x60).
- write in the serial memory, but not a memory data, for example
writing the configuration or the QSPI_SR, TFRTYP must be written
to '2' for sama5d2 and to '0' for sam9x60.
- write in the serial memory in particular to program a memory data,
TFRTYP must be written to '3' for sama5d2 and to '1' for sam9x60.
Fix the setting of the QSPI_IFR.TFRTYP field.
Fixes: 2d30ac5ed6 ("mtd: spi-nor: atmel-quadspi: Use spi-mem interface for atmel-quadspi driver")
Cc: <stable@vger.kernel.org> # v5.0+
Reported-by: Tom Burkart <tom@aussec.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201207135959.154124-2-tudor.ambarus@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46b5c4fb87 upstream.
If the calls to device_reset() or devm_spi_register_controller() fail on
probe of the MediaTek MT7621 SPI driver, the spi_controller struct is
erroneously not freed. Fix by switching over to the new
devm_spi_alloc_master() helper.
Additionally, there's an ordering issue in mt7621_spi_remove() wherein
the spi_controller is unregistered after disabling the SYS clock.
The correct order is to call spi_unregister_controller() *before* this
teardown step because bus accesses may still be ongoing until that
function returns.
All of these bugs have existed since the driver was first introduced,
so it seems fair to fix them together in a single commit.
Fixes: 1ab7f2a435 ("staging: mt7621-spi: add mt7621 support")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: <stable@vger.kernel.org> # v4.17+: 5e844cc37a: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v4.17+
Link: https://lore.kernel.org/r/72b680796149f5fcda0b3f530ffb7ee73b04f224.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f96c434df upstream.
spi_geni_remove() accesses the driver's private data after calling
spi_unregister_master() even though that function releases the last
reference on the spi_master and thereby frees the private data.
Moreover, since commit 1a9e489e61 ("spi: spi-geni-qcom: Use OPP API to
set clk/perf state"), spi_geni_probe() leaks the spi_master allocation
if the calls to dev_pm_opp_set_clkname() or dev_pm_opp_of_add_table()
fail.
Fix by switching over to the new devm_spi_alloc_master() helper which
keeps the private data accessible until the driver has unbound and also
avoids the spi_master leak on probe.
Fixes: 561de45f72 ("spi: spi-geni-qcom: Add SPI driver support for GENI based QUP")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v4.20+: 5e844cc37a: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v4.20+
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Cc: Girish Mahadevan <girishm@codeaurora.org>
Link: https://lore.kernel.org/r/dfa1d8c41b8acdfad87ec8654cd124e6e3cb3f31.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7174dc655e upstream.
If the call to devm_spi_register_master() fails on probe of the GPIO SPI
driver, the spi_master struct is erroneously not freed:
After allocating the spi_master, its reference count is 1. The driver
unconditionally decrements the reference count on unbind using a devm
action. Before calling devm_spi_register_master(), the driver
unconditionally increments the reference count because on success,
that function will decrement the reference count on unbind. However on
failure, devm_spi_register_master() does *not* decrement the reference
count, so the spi_master is leaked.
The issue was introduced by commits 8b797490b4 ("spi: gpio: Make sure
spi_master_put() is called in every error path") and 79567c1a32 ("spi:
gpio: Use devm_spi_register_master()"), which sought to plug leaks
introduced by 9b00bc7b90 ("spi: spi-gpio: Rewrite to use GPIO
descriptors") but missed this remaining leak.
The situation was later aggravated by commit d3b0ffa1d7 ("spi: gpio:
prevent memory leak in spi_gpio_probe"), which introduced a
use-after-free because it releases a reference on the spi_master if
devm_add_action_or_reset() fails even though the function already
does that.
Fix by switching over to the new devm_spi_alloc_master() helper.
Fixes: 9b00bc7b90 ("spi: spi-gpio: Rewrite to use GPIO descriptors")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@vger.kernel.org> # v4.17+: 5e844cc37a: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v5.1-: 8b797490b4: spi: gpio: Make sure spi_master_put() is called in every error path
Cc: <stable@vger.kernel.org> # v5.1-: 45beec3519: spi: bitbang: Introduce spi_bitbang_init()
Cc: <stable@vger.kernel.org> # v5.1-: 79567c1a32: spi: gpio: Use devm_spi_register_master()
Cc: <stable@vger.kernel.org> # v5.4-: d3b0ffa1d7: spi: gpio: prevent memory leak in spi_gpio_probe
Cc: <stable@vger.kernel.org> # v4.17+
Cc: Navid Emamdoost <navid.emamdoost@gmail.com>
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Link: https://lore.kernel.org/r/86eaed27431c3d709e3748eb76ceecbfc790dd37.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 236924ee53 upstream.
If the call to devm_spi_register_controller() fails on probe of the
Qualcomm Atheros AR934x/QCA95xx SPI driver, the spi_controller struct is
erroneously not freed. Fix by switching over to the new
devm_spi_alloc_master() helper.
Moreover, the controller's clock is enabled on probe but not disabled if
any of the subsequent probe steps fail.
Finally, there's an ordering issue in ar934x_spi_remove() wherein the
clock is disabled even though the controller is not yet unregistered.
It is unregistered after ar934x_spi_remove() by the devres framework.
As long as it is not unregistered, SPI transfers may still be ongoing
and disabling the clock may break them. It is not possible to use
devm_spi_register_controller() in this case, so move to the non-devm
variant.
All of these bugs have existed since the driver was first introduced,
so it seems fair to fix them together in a single commit.
Fixes: 047980c582 ("spi: add driver for ar934x spi controller")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v5.7+: 5e844cc37a: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v5.7+
Cc: Chuanhong Guo <gch981213@gmail.com>
Link: https://lore.kernel.org/r/1d58367d74d55741e0c2730a51a2b65012c8ab33.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0fb6ee8d0b upstream.
Use a heap allocated memory for the SPI transfer buffer. Using stack memory
can corrupt stack memory when using DMA on some systems.
This change moves the buffer from the stack of the trigger handler call to
the heap of the buffer of the state struct. The size increases takes into
account the alignment for the timestamp, which is 8 bytes.
The 'data' buffer is split into 'tx_buf' and 'rx_buf', to make a clearer
separation of which part of the buffer should be used for TX & RX.
Fixes: af3008485e ("iio:adc: Add common code for ADI Sigma Delta devices")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20201124123807.19717-1-alexandru.ardelean@analog.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0e53656ad8 upstream.
When inserting a VMA, we restrict the placement to the low 4G unless the
caller opts into using the full range. This was done to allow usersapce
the opportunity to transition slowly from a 32b address space, and to
avoid breaking inherent 32b assumptions of some commands.
However, for insert we limited ourselves to 4G-4K, but on verification
we allowed the full 4G. This causes some attempts to bind a new buffer
to sporadically fail with -ENOSPC, but at other times be bound
successfully.
commit 48ea1e32c3 ("drm/i915/gen9: Set PIN_ZONE_4G end to 4GB - 1
page") suggests that there is a genuine problem with stateless addressing
that cannot utilize the last page in 4G and so we purposefully excluded
it. This means that the quick pin pass may cause us to utilize a buggy
placement.
Reported-by: CQ Tang <cq.tang@intel.com>
Testcase: igt/gem_exec_params/larger-than-life-batch
Fixes: 48ea1e32c3 ("drm/i915/gen9: Set PIN_ZONE_4G end to 4GB - 1 page")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: CQ Tang <cq.tang@intel.com>
Reviewed-by: CQ Tang <cq.tang@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Cc: <stable@vger.kernel.org> # v4.5+
Link: https://patchwork.freedesktop.org/patch/msgid/20201216092951.7124-1-chris@chris-wilson.co.uk
(cherry picked from commit 5f22cc0b13)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eca6ba20f3 upstream.
The only reference to the mlxplat_mlxcpld_psu[] array got removed,
so there is now a warning from clang:
drivers/platform/x86/mlx-platform.c:322:30: error: variable 'mlxplat_mlxcpld_psu' is not needed and will not be emitted [-Werror,-Wunneeded-internal-declaration]
static struct i2c_board_info mlxplat_mlxcpld_psu[] = {
Remove the array as well and adapt the ARRAY_SIZE() call
accordingly.
Fixes: 912b341585 ("platform/x86: mlx-platform: Remove PSU EEPROM from MSN274x platform configuration")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20201203223105.1195709-1-arnd@kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5bc5cc2819 upstream.
We've fixed many races in panfrost_job_timedout() but some remain.
Instead of trying to fix it again, let's simplify the logic and move
the reset bits to a separate work scheduled when one of the queue
reports a timeout.
v5:
- Simplify panfrost_scheduler_stop() (Steven Price)
- Always restart the queue in panfrost_scheduler_start() even if
the status is corrupted (Steven Price)
v4:
- Rework the logic to prevent a race between drm_sched_start()
(reset work) and drm_sched_job_timedout() (timeout work)
- Drop Steven's R-b
- Add dma_fence annotation to the panfrost_reset() function (Daniel Vetter)
v3:
- Replace the atomic_cmpxchg() by an atomic_xchg() (Robin Murphy)
- Add Steven's R-b
v2:
- Use atomic_cmpxchg() to conditionally schedule the reset work
(Steven Price)
Fixes: 1a11a88cfd ("drm/panfrost: Fix job timeout handling")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201105151704.2010667-1-boris.brezillon@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a11a88cfd upstream.
If more than two jobs end up timeout-ing concurrently, only one of them
(the one attached to the scheduler acquiring the lock) is fully handled.
The other one remains in a dangling state where it's no longer part of
the scheduling queue, but still blocks something in scheduler, leading
to repetitive timeouts when new jobs are queued.
Let's make sure all bad jobs are properly handled by the thread
acquiring the lock.
v3:
- Add Steven's R-b
- Don't take the sched_lock when stopping the schedulers
v2:
- Fix the subject prefix
- Stop the scheduler before returning from panfrost_job_timedout()
- Call cancel_delayed_work_sync() after drm_sched_stop() to make sure
no timeout handlers are in flight when we reset the GPU (Steven Price)
- Make sure we release the reset lock before restarting the
schedulers (Steven Price)
Fixes: f3ba91228e ("drm/panfrost: Add initial panfrost driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201002122506.1374183-1-boris.brezillon@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c61b3e4839 upstream.
Bounds checking tools can flag a bug in dbAdjTree() for an array index
out of bounds in dmt_stree. Since dmt_stree can refer to the stree in
both structures dmaptree and dmapctl, use the larger array to eliminate
the false positive.
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Reported-by: butt3rflyh4ck <butterflyhuangxx@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fecc455978 upstream.
fsnotify_parent() used to send two separate events to backends when a
parent inode is watching children and the child inode is also watching.
In an attempt to avoid duplicate events in fanotify, we unified the two
backend callbacks to a single callback and handled the reporting of the
two separate events for the relevant backends (inotify and dnotify).
However the handling is buggy and can result in inotify and dnotify
listeners receiving events of the type they never asked for or spurious
events.
The problem is the unified event callback with two inode marks (parent and
child) is called when any of the parent and child inodes are watched and
interested in the event, but the parent inode's mark that is interested
in the event on the child is not necessarily the one we are currently
reporting to (it could belong to a different group).
So before reporting the parent or child event flavor to backend we need
to check that the mark is really interested in that event flavor.
The semantics of INODE and CHILD marks were hard to follow and made the
logic more complicated than it should have been. Replace it with INODE
and PARENT marks semantics to hopefully make the logic more clear.
Thanks to Hugh Dickins for spotting a bug in the earlier version of this
patch.
Fixes: 497b0c5a7c ("fsnotify: send event to parent and child with single callback")
CC: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20201202120713.702387-4-amir73il@gmail.com
Reported-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 950cc0d2be upstream.
The handle_inode_event() interface was added as (quoting comment):
"a simple variant of handle_event() for groups that only have inode
marks and don't have ignore mask".
In other words, all backends except fanotify. The inotify backend
also falls under this category, but because it required extra arguments
it was left out of the initial pass of backends conversion to the
simple interface.
This results in code duplication between the generic helper
fsnotify_handle_event() and the inotify_handle_event() callback
which also happen to be buggy code.
Generalize the handle_inode_event() arguments and add the check for
FS_EXCL_UNLINK flag to the generic helper, so inotify backend could
be converted to use the simple interface.
Link: https://lore.kernel.org/r/20201202120713.702387-2-amir73il@gmail.com
CC: stable@vger.kernel.org
Fixes: b9a1b97725 ("fsnotify: create method handle_inode_event() in fsnotify_operations")
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 08cd274f9b upstream.
The jffs2 mount options will be ignored when remounting jffs2.
It can be easily reproduced with the steps listed below.
1. mount -t jffs2 -o compr=none /dev/mtdblockx /mnt
2. mount -o remount compr=zlib /mnt
Since ec10a24f10, the option parsing happens before fill_super and
then pass fc, which contains the options parsing results, to function
jffs2_reconfigure during remounting. But function jffs2_reconfigure do
not update c->mount_opts.
This patch add a function jffs2_update_mount_opts to fix this problem.
By the way, I notice that tmpfs use the same way to update remounting
options. If it is necessary to unify them?
Cc: <stable@vger.kernel.org>
Fixes: ec10a24f10 ("vfs: Convert jffs2 to use the new mount API")
Signed-off-by: lizhe <lizhe67@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9afc9a8a49 upstream.
The log of this problem is:
jffs2: Error garbage collecting node at 0x***!
jffs2: No space for garbage collection. Aborting GC thread
This is because GC believe that it do nothing, so it abort.
After going over the image of jffs2, I find a scene that
can trigger this problem stably.
The scene is: there is a normal dirent node at summary-area,
but abnormal at corresponding not-summary-area with error
name_crc.
The reason that GC exit abnormally is because it find that
abnormal dirent node to GC, but when it goes to function
jffs2_add_fd_to_list, it cannot meet the condition listed
below:
if ((*prev)->nhash == new->nhash && !strcmp((*prev)->name, new->name))
So no node is marked obsolete, statistical information of
erase_block do not change, which cause GC exit abnormally.
The root cause of this problem is: we do not check the
name_crc of the abnormal dirent node with summary is enabled.
Noticed that in function jffs2_scan_dirent_node, we use
function jffs2_scan_dirty_space to deal with the dirent
node with error name_crc. So this patch add a checking
code in function read_direntry to ensure the correctness
of dirent node. If checked failed, the dirent node will
be marked obsolete so GC will pass this node and this
problem will be fixed.
Cc: <stable@vger.kernel.org>
Signed-off-by: Zhe Li <lizhe67@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 20f1431160 upstream.
Write buffers use a kmalloc()'ed buffer, they can leak
up to seven bytes of kernel memory to flash if writes are not
aligned.
So use ubifs_pad() to fill these gaps with padding bytes.
This was never a problem while scanning because the scanner logic
manually aligns node lengths and skips over these gaps.
Cc: <stable@vger.kernel.org>
Fixes: 1e51764a3c ("UBIFS: add new flash file system")
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7955f105af upstream.
In the negotiate protocol preauth context, the server is not required
to populate the salt (although it is done by most servers) so do
not warn on mount.
We retain the checks (warn) that the preauth context is the minimum
size and that the salt does not exceed DataLength of the SMB response.
Although we use the defaults in the case that the preauth context
response is invalid, these checks may be useful in the future
as servers add support for additional mechanisms.
CC: Stable <stable@vger.kernel.org>
Reviewed-by: Shyam Prasad N <sprasad@microsoft.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bc7c4129d4 upstream.
Azure does not send an SPNEGO blob in the negotiate protocol response,
so we shouldn't assume that it is there when validating the location
of the first negotiate context. This avoids the potential confusing
mount warning:
CIFS: Invalid negotiate context offset
CC: Stable <stable@vger.kernel.org>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ebcd6de987 upstream.
Mounts to Azure cause an unneeded warning message in dmesg
"CIFS: VFS: parse_server_interfaces: incomplete interface info"
Azure rounds up the size (by 8 additional bytes, to a
16 byte boundary) of the structure returned on the query
of the server interfaces at mount time. This is permissible
even though different than other servers so do not log a warning
if query network interfaces response is only rounded up by 8
bytes or fewer.
CC: Stable <stable@vger.kernel.org>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e5cafce3ad upstream.
A NULL pointer dereference may occur in __ceph_remove_cap with some of the
callbacks used in ceph_iterate_session_caps, namely trim_caps_cb and
remove_session_caps_cb. Those callers hold the session->s_mutex, so they
are prevented from concurrent execution, but ceph_evict_inode does not.
Since the callers of this function hold the i_ceph_lock, the fix is simply
a matter of returning immediately if caps->ci is NULL.
Cc: stable@vger.kernel.org
URL: https://tracker.ceph.com/issues/43272
Suggested-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Luis Henriques <lhenriques@suse.de>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff9632d2a6 upstream.
Since the time-travel rework, basic time-travel mode hasn't worked
properly, but there's no longer a need for this WARN_ON() so just
remove it and thereby fix things.
Cc: stable@vger.kernel.org
Fixes: 4b786e24ca ("um: time-travel: Rewrite as an event scheduler")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 207cdd565d upstream.
Commit a408e4a86b ("ima: open a new file instance if no read
permissions") already introduced a second open to measure a file when the
original file descriptor does not allow it. However, it didn't remove the
existing method of changing the mode of the original file descriptor, which
is still necessary if the current process does not have enough privileges
to open a new one.
Changing the mode isn't really an option, as the filesystem might need to
do preliminary steps to make the read possible. Thus, this patch removes
the code and keeps the second open as the only option to measure a file
when it is unreadable with the original file descriptor.
Cc: <stable@vger.kernel.org> # 4.20.x: 0014cc04e8 ima: Set file->f_mode
Fixes: 2fe5d6def1 ("ima: integrity appraisal extension")
Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 89bdfaf93d upstream.
ovl_ioctl_set_flags() does a capability check using flags, but then the
real ioctl double-fetches flags and uses potentially different value.
The "Check the capability before cred override" comment misleading: user
can skip this check by presenting benign flags first and then overwriting
them to non-benign flags.
Just remove the cred override for now, hoping this doesn't cause a
regression.
The proper solution is to create a new setxflags i_op (patches are in the
works).
Xfstests don't show a regression.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Reviewed-by: Amir Goldstein <amir73il@gmail.com>
Fixes: dab5ca8fd9 ("ovl: add lsattr/chattr support")
Cc: <stable@vger.kernel.org> # v4.19
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d6718941a2 upstream.
It's very easy to crash the kernel right now by simply trying to
enable memtrace concurrently, hammering on the "enable" interface
loop.sh:
#!/bin/bash
dmesg --console-off
while true; do
echo 0x40000000 > /sys/kernel/debug/powerpc/memtrace/enable
done
[root@localhost ~]# loop.sh &
[root@localhost ~]# loop.sh &
Resulting quickly in a kernel crash. Let's properly protect using a
mutex.
Fixes: 9d5171a8f2 ("powerpc/powernv: Enable removal of memory for in memory tracing")
Cc: stable@vger.kernel.org# v4.14+
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201111145322.15793-3-david@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b1198a8823 upstream.
We execute certain NPU2 setup code (such as mapping an LPID to a device
in NPU2) unconditionally if an Nvlink bridge is detected. However this
cannot succeed on POWER8NVL machines and errors appear in dmesg. This is
harmless as skiboot returns an error and the only place we check it is
vfio-pci but that code does not get called on P8+ either.
This adds a check if pnv_npu2_xxx helpers are called on a machine with
NPU2 which initializes pnv_phb::npu in pnv_npu2_init();
pnv_phb::npu==NULL on POWER8/NVL (Naples).
While at this, fix NULL derefencing in pnv_npu_peers_take_ownership/
pnv_npu_peers_release_ownership which occurs when GPUs on mentioned P8s
cause EEH which happens if "vfio-pci" disables devices using
the D3 power state; the vfio-pci's disable_idle_d3 module parameter
controls this and must be set on Naples. The EEH handling clears
the entire pnv_ioda_pe struct in pnv_ioda_free_pe() hence
the NULL derefencing. We cannot recover from that but at least we stop
crashing.
Tested on
- POWER9 pvr=004e1201, Ubuntu 19.04 host, Ubuntu 18.04 vm,
NVIDIA GV100 10de:1db1 driver 418.39
- POWER8 pvr=004c0100, RHEL 7.6 host, Ubuntu 16.10 vm,
NVIDIA P100 10de:15f9 driver 396.47
Fixes: 1b785611e1 ("powerpc/powernv/npu: Add release_ownership hook")
Cc: stable@vger.kernel.org # 5.0
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201122073828.15446-1-aik@ozlabs.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1891ef21d9 upstream.
fls() and fls64() are using __builtin_ctz() and _builtin_ctzll().
On powerpc, those builtins trivially use ctlzw and ctlzd power
instructions.
Allthough those instructions provide the expected result with
input argument 0, __builtin_ctz() and __builtin_ctzll() are
documented as undefined for value 0.
The easiest fix would be to use fls() and fls64() functions
defined in include/asm-generic/bitops/builtin-fls.h and
include/asm-generic/bitops/fls64.h, but GCC output is not optimal:
00000388 <testfls>:
388: 2c 03 00 00 cmpwi r3,0
38c: 41 82 00 10 beq 39c <testfls+0x14>
390: 7c 63 00 34 cntlzw r3,r3
394: 20 63 00 20 subfic r3,r3,32
398: 4e 80 00 20 blr
39c: 38 60 00 00 li r3,0
3a0: 4e 80 00 20 blr
000003b0 <testfls64>:
3b0: 2c 03 00 00 cmpwi r3,0
3b4: 40 82 00 1c bne 3d0 <testfls64+0x20>
3b8: 2f 84 00 00 cmpwi cr7,r4,0
3bc: 38 60 00 00 li r3,0
3c0: 4d 9e 00 20 beqlr cr7
3c4: 7c 83 00 34 cntlzw r3,r4
3c8: 20 63 00 20 subfic r3,r3,32
3cc: 4e 80 00 20 blr
3d0: 7c 63 00 34 cntlzw r3,r3
3d4: 20 63 00 40 subfic r3,r3,64
3d8: 4e 80 00 20 blr
When the input of fls(x) is a constant, just check x for nullity and
return either 0 or __builtin_clz(x). Otherwise, use cntlzw instruction
directly.
For fls64() on PPC64, do the same but with __builtin_clzll() and
cntlzd instruction. On PPC32, lets take the generic fls64() which
will use our fls(). The result is as expected:
00000388 <testfls>:
388: 7c 63 00 34 cntlzw r3,r3
38c: 20 63 00 20 subfic r3,r3,32
390: 4e 80 00 20 blr
000003a0 <testfls64>:
3a0: 2c 03 00 00 cmpwi r3,0
3a4: 40 82 00 10 bne 3b4 <testfls64+0x14>
3a8: 7c 83 00 34 cntlzw r3,r4
3ac: 20 63 00 20 subfic r3,r3,32
3b0: 4e 80 00 20 blr
3b4: 7c 63 00 34 cntlzw r3,r3
3b8: 20 63 00 40 subfic r3,r3,64
3bc: 4e 80 00 20 blr
Fixes: 2fcff790dc ("powerpc: Use builtin functions for fls()/__fls()/fls64()")
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/348c2d3f19ffcff8abe50d52513f989c4581d000.1603375524.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f10881a46f upstream.
Commit bd59380c5b ("powerpc/rtas: Restrict RTAS requests from userspace")
introduced the following error when invoking the errinjct userspace
tool:
[root@ltcalpine2-lp5 librtas]# errinjct open
[327884.071171] sys_rtas: RTAS call blocked - exploit attempt?
[327884.071186] sys_rtas: token=0x26, nargs=0 (called by errinjct)
errinjct: Could not open RTAS error injection facility
errinjct: librtas: open: Unexpected I/O error
The entry for ibm,open-errinjct in rtas_filter array has a typo where
the "j" is omitted in the rtas call name. After fixing this typo the
errinjct tool functions again as expected.
[root@ltcalpine2-lp5 linux]# errinjct open
RTAS error injection facility open, token = 1
Fixes: bd59380c5b ("powerpc/rtas: Restrict RTAS requests from userspace")
Cc: stable@vger.kernel.org
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201208195434.8289-1-tyreld@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d85be8a49e upstream.
The placeholder for instruction selection should use the second
argument's operand, which is %1, not %0. This could generate incorrect
assembly code if the memory addressing of operand %0 is a different
form from that of operand %1.
Also remove the %Un placeholder because having %Un placeholders
for two operands which are based on the same local var (ptep) doesn't
make much sense. By the way, it doesn't change the current behaviour
because "<>" constraint is missing for the associated "=m".
[chleroy: revised commit log iaw segher's comments and removed %U0]
Fixes: 9bf2b5cdc5 ("powerpc: Fixes for CONFIG_PTE_64BIT for SMP support")
Cc: <stable@vger.kernel.org> # v2.6.28+
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/96354bd77977a6a933fe9020da57629007fdb920.1603358942.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d5c243989f upstream.
We need r1 to be properly set before activating MMU, otherwise any new
exception taken while saving registers into the stack in syscall
prologs will use the user stack, which is wrong and will even lockup
or crash when KUAP is selected.
Do that by switching the meaning of r11 and r1 until we have saved r1
to the stack: copy r1 into r11 and setup the new stack pointer in r1.
To avoid complicating and impacting all generic and specific prolog
code (and more), copy back r1 into r11 once r11 is save onto
the stack.
We could get rid of copying r1 back and forth at the cost of rewriting
everything to use r1 instead of r11 all the way when CONFIG_VMAP_STACK
is set, but the effort is probably not worth it for now.
Fixes: da7bb43ab9 ("powerpc/32: Fix vmap stack - Properly set r1 before activating MMU")
Cc: stable@vger.kernel.org # v5.10+
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/a3d819d5c348cee9783a311d5d3f3ba9b48fd219.1608531452.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 15261b9126 upstream.
Olga K. observed that rpcrdma_marsh_req() allocates sparse pages
only when it has determined that a Reply chunk is necessary. There
are plenty of cases where no Reply chunk is needed, but the
XDRBUF_SPARSE_PAGES flag is set. The result would be a crash in
rpcrdma_inline_fixup() when it tries to copy parts of the received
Reply into a missing page.
To avoid crashing, handle sparse page allocation up front.
Until XATTR support was added, this issue did not appear often
because the only SPARSE_PAGES consumer always expected a reply large
enough to always require a Reply chunk.
Reported-by: Olga Kornievskaia <kolga@netapp.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd7cd7e05a upstream.
Commit 9ce2746304 ("cpufreq: tegra20: Use generic cpufreq-dt driver
(Tegra30 supported now)") update the Tegra20 CPUFREQ driver to use the
generic CPUFREQ device-tree driver. Since this change CPUFREQ support
on the Tegra20 Ventana platform has been broken because the necessary
device-tree nodes with the operating point information are not populated
for this platform. Fix this by updating device-tree for Venata to
include the operating point informration for Tegra20.
Fixes: 9ce2746304 ("cpufreq: tegra20: Use generic cpufreq-dt driver (Tegra30 supported now)")
Cc: stable@vger.kernel.org
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 85b8350ae9 upstream.
CAN0 and CAN1 instances share the same message ram configured
at 0x210000 on sama5d2 Linux systems.
According to current configuration of CAN0, we need 0x1c00 bytes
so that the CAN1 don't overlap its message ram:
64 x RX FIFO0 elements => 64 x 72 bytes
32 x TXE (TX Event FIFO) elements => 32 x 8 bytes
32 x TXB (TX Buffer) elements => 32 x 72 bytes
So a total of 7168 bytes (0x1C00).
Fix offset to match this needed size.
Make the CAN0 message ram ioremap match exactly this size so that is
easily understandable. Adapt CAN1 size accordingly.
Fixes: bc6d5d7666 ("ARM: dts: at91: sama5d2: add m_can nodes")
Reported-by: Dan Sneddon <dan.sneddon@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Cristian Birsan <cristian.birsan@microchip.com>
Cc: stable@vger.kernel.org # v4.13+
Link: https://lore.kernel.org/r/20201203091949.9015-1-nicolas.ferre@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9081b8ff5 upstream.
The firmware found in some Qualcomm platforms intercepts writes to S2CR
in order to replace bypass type streams with fault; and ignore S2CR
updates of type fault.
Detect this behavior and implement a custom write_s2cr function in order
to trick the firmware into supporting bypass streams by the means of
configuring the stream for translation using a reserved and disabled
context bank.
Also circumvent the problem of configuring faulting streams by
configuring the stream as bypass.
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/20201019182323.3162386-4-bjorn.andersson@linaro.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9d4747d023 upstream.
When both KVM support and the CCP driver are built into the kernel instead
of as modules, KVM initialization can happen before CCP initialization. As
a result, sev_platform_status() will return a failure when it is called
from sev_hardware_setup(), when this isn't really an error condition.
Since sev_platform_status() doesn't need to be called at this time anyway,
remove the invocation from sev_hardware_setup().
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Message-Id: <618380488358b56af558f2682203786f09a49483.1607620209.git.thomas.lendacky@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 39485ed95d upstream.
Until commit e7c587da12 ("x86/speculation: Use synthetic bits for
IBRS/IBPB/STIBP"), KVM was testing both Intel and AMD CPUID bits before
allowing the guest to write MSR_IA32_SPEC_CTRL and MSR_IA32_PRED_CMD.
Testing only Intel bits on VMX processors, or only AMD bits on SVM
processors, fails if the guests are created with the "opposite" vendor
as the host.
While at it, also tweak the host CPU check to use the vendor-agnostic
feature bit X86_FEATURE_IBPB, since we only care about the availability
of the MSR on the host here and not about specific CPUID bits.
Fixes: e7c587da12 ("x86/speculation: Use synthetic bits for IBRS/IBPB/STIBP")
Cc: stable@vger.kernel.org
Reported-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f43cadef2d upstream.
FW has to configure devices' StreamIDs so that SMMU is able to lookup
context and do proper translation later on. For Armada 7040 & 8040 and
publicly available FW, most of the devices are configured properly,
but some like ap_sdhci0, PCIe, NIC still remain unassigned which
results in SMMU faults about unmatched StreamID (assuming
ARM_SMMU_DISABLE_BYPASS_BY_DEFAUL=y).
Since there is dependency on custom FW let SMMU be disabled by default.
People who still willing to use SMMU need to enable manually and
use ARM_SMMU_DISABLE_BYPASS_BY_DEFAUL=n (or via kernel command line)
with extra caution.
Fixes: 83a3545d9c ("arm64: dts: marvell: add SMMU support")
Cc: <stable@vger.kernel.org> # 5.9+
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46e294efc3 upstream.
Xattr code using inodes with large xattr data can end up dropping last
inode reference (and thus deleting the inode) from places like
ext4_xattr_set_entry(). That function is called with transaction started
and so ext4_evict_inode() can deadlock against fs freezing like:
CPU1 CPU2
removexattr() freeze_super()
vfs_removexattr()
ext4_xattr_set()
handle = ext4_journal_start()
...
ext4_xattr_set_entry()
iput(old_ea_inode)
ext4_evict_inode(old_ea_inode)
sb->s_writers.frozen = SB_FREEZE_FS;
sb_wait_write(sb, SB_FREEZE_FS);
ext4_freeze()
jbd2_journal_lock_updates()
-> blocks waiting for all
handles to stop
sb_start_intwrite()
-> blocks as sb is already in SB_FREEZE_FS state
Generally it is advisable to delete inodes from a separate transaction
as it can consume quite some credits however in this case it would be
quite clumsy and furthermore the credits for inode deletion are quite
limited and already accounted for. So just tweak ext4_evict_inode() to
avoid freeze protection if we have transaction already started and thus
it is not really needed anyway.
Cc: stable@vger.kernel.org
Fixes: dec214d00e ("ext4: xattr inode deduplication")
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Link: https://lore.kernel.org/r/20201127110649.24730-1-jack@suse.cz
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cca4155372 upstream.
When freeing metadata, we will create an ext4_free_data and
insert it into the pending free list. After the current
transaction is committed, the object will be freed.
ext4_mb_free_metadata() will check whether the area to be freed
overlaps with the pending free list. If true, return directly. At this
time, ext4_free_data is leaked. Fortunately, the probability of this
problem is small, since it only occurs if the file system is corrupted
such that a block is claimed by more one inode and those inodes are
deleted within a single jbd2 transaction.
Signed-off-by: Chunguang Xu <brookxu@tencent.com>
Link: https://lore.kernel.org/r/1604764698-4269-8-git-send-email-brookxu@tencent.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7f458a3873 upstream.
When defragmenting we skip ranges that have holes or inline extents, so that
we don't do unnecessary IO and waste space. We do this check when calling
should_defrag_range() at btrfs_defrag_file(). However we do it without
holding the inode's lock. The reason we do it like this is to avoid
blocking other tasks for too long, that possibly want to operate on other
file ranges, since after the call to should_defrag_range() and before
locking the inode, we trigger a synchronous page cache readahead. However
before we were able to lock the inode, some other task might have punched
a hole in our range, or we may now have an inline extent there, in which
case we should not set the range for defrag anymore since that would cause
unnecessary IO and make us waste space (i.e. allocating extents to contain
zeros for a hole).
So after we locked the inode and the range in the iotree, check again if
we have holes or an inline extent, and if we do, just skip the range.
I hit this while testing my next patch that fixes races when updating an
inode's number of bytes (subject "btrfs: update the number of bytes used
by an inode atomically"), and it depends on this change in order to work
correctly. Alternatively I could rework that other patch to detect holes
and flag their range with the 'new delalloc' bit, but this itself fixes
an efficiency problem due a race that from a functional point of view is
not harmful (it could be triggered with btrfs/062 from fstests).
CC: stable@vger.kernel.org # 5.4+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 27d56e62e4 upstream.
While writing an explanation for the need of the commit_root_sem for
btrfs_prepare_extent_commit, I realized we have a slight hole that could
result in leaked space if we have to do the old style caching. Consider
the following scenario
commit root
+----+----+----+----+----+----+----+
|\\\\| |\\\\|\\\\| |\\\\|\\\\|
+----+----+----+----+----+----+----+
0 1 2 3 4 5 6 7
new commit root
+----+----+----+----+----+----+----+
| | | |\\\\| | |\\\\|
+----+----+----+----+----+----+----+
0 1 2 3 4 5 6 7
Prior to this patch, we run btrfs_prepare_extent_commit, which updates
the last_byte_to_unpin, and then we subsequently run
switch_commit_roots. In this example lets assume that
caching_ctl->progress == 1 at btrfs_prepare_extent_commit() time, which
means that cache->last_byte_to_unpin == 1. Then we go and do the
switch_commit_roots(), but in the meantime the caching thread has made
some more progress, because we drop the commit_root_sem and re-acquired
it. Now caching_ctl->progress == 3. We swap out the commit root and
carry on to unpin.
The race can happen like:
1) The caching thread was running using the old commit root when it
found the extent for [2, 3);
2) Then it released the commit_root_sem because it was in the last
item of a leaf and the semaphore was contended, and set ->progress
to 3 (value of 'last'), as the last extent item in the current leaf
was for the extent for range [2, 3);
3) Next time it gets the commit_root_sem, will start using the new
commit root and search for a key with offset 3, so it never finds
the hole for [2, 3).
So the caching thread never saw [2, 3) as free space in any of the
commit roots, and by the time finish_extent_commit() was called for
the range [0, 3), ->last_byte_to_unpin was 1, so it only returned the
subrange [0, 1) to the free space cache, skipping [2, 3).
In the unpin code we have last_byte_to_unpin == 1, so we unpin [0,1),
but do not unpin [2,3). However because caching_ctl->progress == 3 we
do not see the newly freed section of [2,3), and thus do not add it to
our free space cache. This results in us missing a chunk of free space
in memory (on disk too, unless we have a power failure before writing
the free space cache to disk).
Fix this by making sure the ->last_byte_to_unpin is set at the same time
that we swap the commit roots, this ensures that we will always be
consistent.
CC: stable@vger.kernel.org # 5.8+
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
[ update changelog with Filipe's review comments ]
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9076dbd5ee upstream.
While fixing up our ->last_byte_to_unpin locking I noticed that we will
shorten len based on ->last_byte_to_unpin if we're caching when we're
adding back the free space. This is correct for the free space, as we
cannot unpin more than ->last_byte_to_unpin, however we use len to
adjust the ->bytes_pinned counters and such, which need to track the
actual pinned usage. This could result in
WARN_ON(space_info->bytes_pinned) triggering at unmount time.
Fix this by using a local variable for the amount to add to free space
cache, and leave len untouched in this case.
CC: stable@vger.kernel.org # 5.4+
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 320f9028c7 upstream.
The driver did not update its view of the available device buffer space
until write() was called in task context. This meant that write_room()
would return 0 even after the device had sent a write-unthrottle
notification, something which could lead to blocked writers not being
woken up (e.g. when using OPOST).
Note that we must also request an unthrottle notification is case a
write() request fills the device buffer exactly.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 49fbb8e37a upstream.
The driver's transmit-unthrottle work was never flushed on disconnect,
something which could lead to the driver port data being freed while the
unthrottle work is still scheduled.
Fix this by cancelling the unthrottle work when shutting down the port.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 37faf50615 upstream.
The driver's deferred write wakeup was never flushed on disconnect,
something which could lead to the driver port data being freed while the
wakeup work is still scheduled.
Fix this by using the usb-serial write wakeup which gets cancelled
properly on disconnect.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c01d2c5869 upstream.
Make sure to clear the write-busy flag also in case no new data was
submitted due to lack of device buffer space so that writing is
resumed once space again becomes available.
Fixes: 507ca9bc04 ("[PATCH] USB: add ability for usb-serial drivers to determine if their write urb is currently being used.")
Cc: stable <stable@vger.kernel.org> # 2.6.13
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7353cad7ee upstream.
The write() callback can be called in interrupt context (e.g. when used
as a console) so interrupts must be disabled while holding the port lock
to prevent a possible deadlock.
Fixes: e81ee637e4 ("usb-serial: possible irq lock inversion (PPP vs. usb/serial)")
Fixes: 507ca9bc04 ("[PATCH] USB: add ability for usb-serial drivers to determine if their write urb is currently being used.")
Cc: stable <stable@vger.kernel.org> # 2.6.19
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 696c541c8c upstream.
Commit c528fcb116 ("USB: serial: keyspan_pda: fix receive sanity
checks") broke write-unthrottle handling by dropping well-formed
unthrottle-interrupt packets which are precisely two bytes long. This
could lead to blocked writers not being woken up when buffer space again
becomes available.
Instead, stop unconditionally printing the third byte which is
(presumably) only valid on modem-line changes.
Fixes: c528fcb116 ("USB: serial: keyspan_pda: fix receive sanity checks")
Cc: stable <stable@vger.kernel.org> # 4.11
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5098e77962 upstream.
The driver must not call tty_wakeup() while holding its private lock as
line disciplines are allowed to call back into write() from
write_wakeup(), leading to a deadlock.
Also remove the unneeded work struct that was used to defer wakeup in
order to work around a possible race in ancient times (see comment about
n_tty write_chan() in commit 14b54e39b4 ("USB: serial: remove
changelogs and old todo entries")).
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 975323ab8f upstream.
The parallel-port restore operations is called when a driver claims the
port and is supposed to restore the provided state (e.g. saved when
releasing the port).
Fixes: b69578df7e ("USB: usbserial: mos7720: add support for parallel port on moschip 7715")
Cc: stable <stable@vger.kernel.org> # 2.6.35
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 406100f3da upstream.
One of our machines keeled over trying to rebuild the scheduler domains.
Mainline produces the same splat:
BUG: unable to handle page fault for address: 0000607f820054db
CPU: 2 PID: 149 Comm: kworker/1:1 Not tainted 5.10.0-rc1-master+ #6
Workqueue: events cpuset_hotplug_workfn
RIP: build_sched_domains
Call Trace:
partition_sched_domains_locked
rebuild_sched_domains_locked
cpuset_hotplug_workfn
It happens with cgroup2 and exclusive cpusets only. This reproducer
triggers it on an 8-cpu vm and works most effectively with no
preexisting child cgroups:
cd $UNIFIED_ROOT
mkdir cg1
echo 4-7 > cg1/cpuset.cpus
echo root > cg1/cpuset.cpus.partition
# with smt/control reading 'on',
echo off > /sys/devices/system/cpu/smt/control
RIP maps to
sd->shared = *per_cpu_ptr(sdd->sds, sd_id);
from sd_init(). sd_id is calculated earlier in the same function:
cpumask_and(sched_domain_span(sd), cpu_map, tl->mask(cpu));
sd_id = cpumask_first(sched_domain_span(sd));
tl->mask(cpu), which reads cpu_sibling_map on x86, returns an empty mask
and so cpumask_first() returns >= nr_cpu_ids, which leads to the bogus
value from per_cpu_ptr() above.
The problem is a race between cpuset_hotplug_workfn() and a later
offline of CPU N. cpuset_hotplug_workfn() updates the effective masks
when N is still online, the offline clears N from cpu_sibling_map, and
then the worker uses the stale effective masks that still have N to
generate the scheduling domains, leading the worker to read
N's empty cpu_sibling_map in sd_init().
rebuild_sched_domains_locked() prevented the race during the cgroup2
cpuset series up until the Fixes commit changed its check. Make the
check more robust so that it can detect an offline CPU in any exclusive
cpuset's effective mask, not just the top one.
Fixes: 0ccea8feb9 ("cpuset: Make generate_sched_domains() work with partition")
Signed-off-by: Daniel Jordan <daniel.m.jordan@oracle.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20201112171711.639541-1-daniel.m.jordan@oracle.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 706657b1fe upstream.
In order to setup its PCI component, the driver needs any node private
instance in order to get a reference to the PCI device and hand that
into edac_pci_create_generic_ctl(). For convenience, it uses the 0th
memory controller descriptor under the assumption that if any, the 0th
will be always present.
However, this assumption goes wrong when the 0th node doesn't have
memory and the driver doesn't initialize an instance for it:
EDAC amd64: F17h detected (node 0).
...
EDAC amd64: Node 0: No DIMMs detected.
But looking up node instances is not really needed - all one needs is
the pointer to the proper device which gets discovered during instance
init.
So stash that pointer into a variable and use it when setting up the
EDAC PCI component.
Clear that variable when the driver needs to unwind due to some
instances failing init to avoid any registration imbalance.
Cc: <stable@vger.kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20201122150815.13808-1-bp@alien8.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f3456b9fd2 upstream.
ARM Cortex-A57 and Cortex-A72 cores running in 32-bit mode are affected
by silicon errata #1742098 and #1655431, respectively, where the second
instruction of a AES instruction pair may execute twice if an interrupt
is taken right after the first instruction consumes an input register of
which a single 32-bit lane has been updated the last time it was modified.
This is not such a rare occurrence as it may seem: in counter mode, only
the least significant 32-bit word is incremented in the absence of a
carry, which makes our counter mode implementation susceptible to these
errata.
So let's shuffle the counter assignments around a bit so that the most
recent updates when the AES instruction pair executes are 128-bit wide.
[0] ARM-EPM-049219 v23 Cortex-A57 MPCore Software Developers Errata Notice
[1] ARM-EPM-012079 v11.0 Cortex-A72 MPCore Software Developers Errata Notice
Cc: <stable@vger.kernel.org> # v5.4+
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 17858b140b upstream.
ecdh_set_secret() casts a void* pointer to a const u64* in order to
feed it into ecc_is_key_valid(). This is not generally permitted by
the C standard, and leads to actual misalignment faults on ARMv6
cores. In some cases, these are fixed up in software, but this still
leads to performance hits that are entirely avoidable.
So let's copy the key into the ctx buffer first, which we will do
anyway in the common case, and which guarantees correct alignment.
Cc: <stable@vger.kernel.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e40ad84c26 upstream.
When turbo has been disabled by the BIOS, but HWP_CAP.GUARANTEED is
changed later, user space may want to take advantage of this increased
guaranteed performance.
HWP_CAP.GUARANTEED is not a static value. It can be adjusted by an
out-of-band agent or during an Intel Speed Select performance level
change. The HWP_CAP.MAX is still the maximum achievable performance
with turbo disabled by the BIOS, so HWP_CAP.GUARANTEED can still
change as long as it remains less than or equal to HWP_CAP.MAX.
When HWP_CAP.GUARANTEED is changed, the sysfs base_frequency
attribute shows the most recent guaranteed frequency value. This
attribute can be used by user space software to update the scaling
min/max limits of the CPU.
Currently, the ->setpolicy() callback already uses the latest
HWP_CAP values when setting HWP_REQ, but the ->verify() callback will
restrict the user settings to the to old guaranteed performance value
which prevents user space from making use of the extra CPU capacity
theoretically available to it after increasing HWP_CAP.GUARANTEED.
To address this, read HWP_CAP in intel_pstate_verify_cpu_policy()
to obtain the maximum P-state that can be used and use that to
confine the policy max limit instead of using the cached and
possibly stale pstate.max_freq value for this purpose.
For consistency, update intel_pstate_update_perf_limits() to use the
maximum available P-state returned by intel_pstate_get_hwp_max() to
compute the maximum frequency instead of using the return value of
intel_pstate_get_max_freq() which, again, may be stale.
This issue is a side-effect of fixing the scaling frequency limits in
commit eacc9c5a92 ("cpufreq: intel_pstate: Fix intel_pstate_get_hwp_max()
for turbo disabled") which corrected the setting of the reduced scaling
frequency values, but caused stale HWP_CAP.GUARANTEED to be used in
the case at hand.
Fixes: eacc9c5a92 ("cpufreq: intel_pstate: Fix intel_pstate_get_hwp_max() for turbo disabled")
Reported-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: 5.8+ <stable@vger.kernel.org> # 5.8+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 56c90457eb upstream.
I have had reports from two different people that attempts to read the
analog input channels of the MF624 board fail with an `ETIMEDOUT` error.
After triggering the conversion, the code calls `comedi_timeout()` with
`mf6x4_ai_eoc()` as the callback function to check if the conversion is
complete. The callback returns 0 if complete or `-EBUSY` if not yet
complete. `comedi_timeout()` returns `-ETIMEDOUT` if it has not
completed within a timeout period which is propagated as an error to the
user application.
The existing code considers the conversion to be complete when the EOLC
bit is high. However, according to the user manuals for the MF624 and
MF634 boards, this test is incorrect because EOLC is an active low
signal that goes high when the conversion is triggered, and goes low
when the conversion is complete. Fix the problem by inverting the test
of the EOLC bit state.
Fixes: 04b565021a ("comedi: Humusoft MF634 and MF624 DAQ cards driver")
Cc: <stable@vger.kernel.org> # v4.4+
Cc: Rostislav Lisovy <lisovy@gmail.com>
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20201207145806.4046-1-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0d024a8bec upstream.
The cx2072x codec driver defines multiple DAIs with the same stream
name "Playback" and "Capture". Although the current code works more
or less as is as the secondary streams are never used, it still leads
the error message like:
debugfs: File 'Playback' in directory 'dapm' already present!
debugfs: File 'Capture' in directory 'dapm' already present!
Fix it by renaming the secondary streams to unique names.
Fixes: a497a43637 ("ASoC: Add support for Conexant CX2072X CODEC")
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20201208135154.9188-1-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 53a7f65583 upstream.
In dasd_alias_disconnect_device_from_lcu the device is removed from any
list on the LCU. Afterwards the LCU is removed from the lcu list if it
does not contain devices any longer.
The lcu->lock protects the lcu from parallel updates. But to cancel all
workers and wait for completion the lcu->lock has to be unlocked.
If two devices are removed in parallel and both are removed from the LCU
the first device that takes the lcu->lock again will delete the LCU because
it is already empty but the second device also tries to free the LCU which
leads to a list corruption of the lcu list.
Fix by removing the device right before the lcu is checked without
unlocking the lcu->lock in between.
Fixes: 8e09f21574 ("[S390] dasd: add hyper PAV support to DASD device driver, part 1")
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0ede91f83a upstream.
dasd_alias_add_device() moves devices to the active_devices list in case
of a scheduled LCU update regardless if they have previously been in a
pavgroup or not.
Example: device A and B are in the same pavgroup.
Device A has already been in a pavgroup and the private->pavgroup pointer
is set and points to a valid pavgroup. While going through dasd_add_device
it is moved from the pavgroup to the active_devices list.
In parallel device B might be removed from the same pavgroup in
remove_device_from_lcu() which in turn checks if the group is empty
and deletes it accordingly because device A has already been removed from
there.
When now device A enters remove_device_from_lcu() it is tried to remove it
from the pavgroup again because the pavgroup pointer is still set and again
the empty group will be cleaned up which leads to a list corruption.
Fix by setting private->pavgroup to NULL in dasd_add_device.
If the device has been the last device on the pavgroup an empty pavgroup
remains but this will be cleaned up by the scheduled lcu_update which
iterates over all existing pavgroups.
Fixes: 8e09f21574 ("[S390] dasd: add hyper PAV support to DASD device driver, part 1")
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a29ea01653 upstream.
Prevent _lcu_update from adding a device to a pavgroup if the LCU still
requires an update. The data is not reliable any longer and in parallel
devices might have been moved on the lists already.
This might lead to list corruptions or invalid PAV grouping.
Only add devices to a pavgroup if the LCU is up to date. Additional steps
are taken by the scheduled lcu update.
Fixes: 8e09f21574 ("[S390] dasd: add hyper PAV support to DASD device driver, part 1")
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 658a337a60 upstream.
For an LCU update a read unit address configuration IO is required.
This is started using sleep_on(), which has early exit paths in case the
device is not usable for IO. For example when it is in offline processing.
In those cases the LCU update should fail and not be retried.
Therefore lcu_update_work checks if EOPNOTSUPP is returned or not.
Commit 41995342b4 ("s390/dasd: fix endless loop after read unit address configuration")
accidentally removed the EOPNOTSUPP return code from
read_unit_address_configuration(), which in turn might lead to an endless
loop of the LCU update in offline processing.
Fix by returning EOPNOTSUPP again if the device is not able to perform the
request.
Fixes: 41995342b4 ("s390/dasd: fix endless loop after read unit address configuration")
Cc: stable@vger.kernel.org #5.3
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 454efcf82e upstream.
When a machine check interrupt is triggered during idle, the code
is using the async timer/clock for idle time calculation. It should use
the machine check enter timer/clock which is passed to the macro.
Fixes: 0b0ed657fe ("s390: remove critical section cleanup from entry.S")
Cc: <stable@vger.kernel.org> # 5.8
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e259b3fafa upstream.
During removal of the critical section cleanup the calculation
of mt_cycles during idle was removed. This causes invalid
accounting on systems with SMT enabled.
Fixes: 0b0ed657fe ("s390: remove critical section cleanup from entry.S")
Cc: <stable@vger.kernel.org> # 5.8
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 613775d62e upstream.
diag308 subcode 0 performes a clear reset which inlcudes the reset of
all registers in the system. While this is the preferred behavior when
loading a normal kernel via kexec it prevents the crash kernel to store
the register values in the dump. To prevent this use subcode 1 when
loading a crash kernel instead.
Fixes: ee337f5469 ("s390/kexec_file: Add crash support to image loader")
Cc: <stable@vger.kernel.org> # 4.17
Signed-off-by: Philipp Rudo <prudo@linux.ibm.com>
Reported-by: Xiaoying Yan <yiyan@redhat.com>
Tested-by: Lianbo Jiang <lijiang@redhat.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5e438ebd7 upstream.
Not resetting the SMT siblings might leave them in unpredictable
state. One of the observed problems was that the CPU timer wasn't
reset and therefore large system time values where accounted during
CPU bringup.
Cc: <stable@kernel.org> # 4.0
Fixes: 10ad34bc76 ("s390: add SMT support")
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 34cdf405aa upstream.
Acer TravelMate laptops P648/P658 series with codec ALC282 only have
one physical jack for headset but there's a confusing lineout pin on
NID 0x1b reported. Audio applications hence misunderstand that there
are a speaker and a lineout, and take the lineout as the default audio
output.
Add a new quirk to remove the useless lineout and enable the pin 0x18
for jack sensing and headset microphone.
Signed-off-by: Chris Chiu <chiu@endlessos.org>
Signed-off-by: Jian-Hong Pan <jhp@endlessos.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201216125200.27053-1-chiu@endlessos.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ca653e3f7 upstream.
The Quanta NL3 laptop has both a headphone output jack and a headset
jack, on the right edge of the chassis.
The pin information suggests that both of these are at the Front.
The PulseAudio is confused to differentiate them so one of the jack
can neither get the jack sense working nor the audio output.
The ALC269_FIXUP_LIFEBOOK chained with ALC269_FIXUP_QUANTA_MUTE can
help to differentiate 2 jacks and get the 'Auto-Mute Mode' working
correctly.
Signed-off-by: Chris Chiu <chiu@endlessos.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201222150459.9545-1-chiu@endlessos.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c72b9bfe0f upstream.
This change could fix 2 issues on this machine:
- the bass speaker's output volume can't be adjusted, that is because
the bass speaker is routed to the DAC (Nid 0x6) which has no volume
control.
- after plugging a headset with vol+, vol- and pause buttons on it,
press those buttons, nothing happens, this means those buttons
don't work at all. This machine has alc287 codec, need to add the
codec id to the disable/enable_headset_jack_key(), then the headset
button could work.
The quirk of ALC285_FIXUP_THINKPAD_HEADSET_JACK could fix both of these
2 issues.
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Link: https://lore.kernel.org/r/20201205051130.8122-1-hui.wang@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2506318e38 upstream.
It seems that the HD-audio clear and reconfig sysfs don't work any
longer after the recent driver core change. There are multiple issues
around that: the linked list corruption and the dead device handling.
The former issue is fixed by another patch for the driver core itself,
while the latter patch needs to be addressed in HD-audio side.
This patch corresponds to the latter, it recovers those broken
functions by replacing the device detach and attach actions with the
standard core API functions, which are almost equivalent with unbind
and bind actions.
Fixes: 654888327e ("driver core: Avoid binding drivers to dead devices")
Cc: <stable@vger.kernel.org>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=209207
Link: https://lore.kernel.org/r/20201209150119.7705-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b08221c40f upstream.
Recently we met a touchscreen problem on some Thinkpad machines, the
touchscreen driver (i2c-hid) is not loaded and the touchscreen can't
work.
An i2c ACPI device with the name WACF2200 is defined in the BIOS, with
the current rule in matching_id(), this device will be regarded as
a PNP device since there is WACFXXX in the acpi_pnp_device_ids[] and
this PNP device is attached to the acpi device as the 1st
physical_node, this will make the i2c bus match fail when i2c bus
calls acpi_companion_match() to match the acpi_id_table in the i2c-hid
driver.
WACF2200 is an i2c device instead of a PNP device, after adding the
string length comparing, the matching_id() will return false when
matching WACF2200 and WACFXXX, and it is reasonable to compare the
string length when matching two IDs.
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 12fc4dad94 upstream.
This reverts commit 8a66790b78.
Switching this function to AE_CTRL_TERMINATE broke the documented
behaviour of acpi_dev_get_resources() - AE_CTRL_TERMINATE does not, in
fact, terminate the resource walk because acpi_walk_resource_buffer()
ignores it (specifically converting it to AE_OK), referring to that
value as "an OK termination by the user function". This means that
acpi_dev_get_resources() does not abort processing when the preproc
function returns a negative value.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Cc: 3.10+ <stable@vger.kernel.org> # 3.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7482c5cb90 upstream.
The idea behind acpi_pm_set_bridge_wakeup() was to allow bridges to
be reference counted for wakeup enabling, because they may be enabled
to signal wakeup on behalf of their subordinate devices and that
may happen for multiple times in a row, whereas for the other devices
it only makes sense to enable wakeup signaling once.
However, this becomes problematic if the bridge itself is suspended,
because it is treated as a "regular" device in that case and the
reference counting doesn't work.
For instance, suppose that there are two devices below a bridge and
they both can signal wakeup. Every time one of them is suspended,
wakeup signaling is enabled for the bridge, so when they both have
been suspended, the bridge's wakeup reference counter value is 2.
Say that the bridge is suspended subsequently and acpi_pci_wakeup()
is called for it. Because the bridge can signal wakeup, that
function will invoke acpi_pm_set_device_wakeup() to configure it
and __acpi_pm_set_device_wakeup() will be called with the last
argument equal to 1. This causes __acpi_device_wakeup_enable()
invoked by it to omit the reference counting, because the reference
counter of the target device (the bridge) is 2 at that time.
Now say that the bridge resumes and one of the device below it
resumes too, so the bridge's reference counter becomes 0 and
wakeup signaling is disabled for it, but there is still the other
suspended device which may need the bridge to signal wakeup on its
behalf and that is not going to work.
To address this scenario, use wakeup enable reference counting for
all devices, not just for bridges, so drop the last argument from
__acpi_device_wakeup_enable() and __acpi_pm_set_device_wakeup(),
which causes acpi_pm_set_device_wakeup() and
acpi_pm_set_bridge_wakeup() to become identical, so drop the latter
and use the former instead of it everywhere.
Fixes: 1ba51a7c14 ("ACPI / PCI / PM: Rework acpi_pci_propagate_wakeup()")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: 4.14+ <stable@vger.kernel.org> # 4.14+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a7e3d7f05 upstream.
Dan reports that smatch thinks userspace can craft an out-of-bound bus
family number. However, nd_cmd_clear_to_send() blocks all non-zero
values of bus-family since only the kernel can initiate these commands.
However, in the speculation path, family is a user controlled array
index value so mask it for speculation safety. Also, since the
nd_cmd_clear_to_send() safety is non-obvious and possibly may change in
the future include input validation as if userspace could get past the
nd_cmd_clear_to_send() gatekeeper.
Link: http://lore.kernel.org/r/20201111113000.GA1237157@mwanda
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 6450ddbd5d ("ACPI: NFIT: Define runtime firmware activation commands")
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f051ae4f6c upstream.
gcc -Warray-bounds warns about a serious bug in
cyapa_pip_retrieve_data_structure:
drivers/input/mouse/cyapa_gen6.c: In function 'cyapa_pip_retrieve_data_structure.constprop':
include/linux/unaligned/access_ok.h:40:17: warning: array subscript -1 is outside array bounds of 'struct retrieve_data_struct_cmd[1]' [-Warray-bounds]
40 | *((__le16 *)p) = cpu_to_le16(val);
drivers/input/mouse/cyapa_gen6.c:569:13: note: while referencing 'cmd'
569 | } __packed cmd;
| ^~~
Apparently the '-2' was added to the pointer instead of the value,
writing garbage into the stack next to this variable.
Fixes: c2c06c41f7 ("Input: cyapa - add gen6 device module support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20201026161332.3708389-1-arnd@kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e297ddf296 upstream.
If the call to spi_register_master() fails on probe of the NetUP
Universal DVB driver, the spi_master struct is erroneously not freed.
Likewise, if spi_new_device() fails, the spi_controller struct is
not unregistered. Plug the leaks.
While at it, fix an ordering issue in netup_spi_release() wherein
spi_unregister_master() is called after fiddling with the IRQ control
register. The correct order is to call spi_unregister_master() *before*
this teardown step because bus accesses may still be ongoing until that
function returns.
Fixes: 52b1eaf4c5 ("[media] netup_unidvb: NetUP Universal DVB-S/S2/T/T2/C PCI-E card driver")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Cc: <stable@vger.kernel.org> # v4.3+: 5e844cc37a: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v4.3+
Cc: Kozlov Sergey <serjk@netup.ru>
Link: https://lore.kernel.org/r/c4c24f333fc7840f4a3db24789e6e10dd660bede.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f56df4c8f upstream.
If a user holds a button down on a remote, then no ir idle interrupt will
be generated until the user releases the button, depending on how quickly
the remote repeats. No IR is processed until that point, which means that
holding down a button may not do anything.
This also resolves an issue on a Cubieboard 1 where the IR receiver is
picking up ambient infrared as IR and spews out endless
"rc rc0: IR event FIFO is full!" messages unless you choose to live in
the dark.
Cc: stable@vger.kernel.org
Tested-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 00c18640c2 upstream.
Before IORING_SETUP_ATTACH_WQ, we could just cancel everything on the
io-wq when exiting. But that's not the case if they are shared, so
cancel for the specific ctx instead.
Cc: stable@vger.kernel.org
Fixes: 24369c2e3b ("io_uring: add io-wq workqueue sharing")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c07e671951 upstream.
io_iopoll_complete() does not hold completion_lock to complete polled io,
so in io_wq_submit_work(), we can not call io_req_complete() directly, to
complete polled io, otherwise there maybe concurrent access to cqring,
defer_list, etc, which is not safe. Commit dad1b1242f ("io_uring: always
let io_iopoll_complete() complete polled io") has fixed this issue, but
Pavel reported that IOPOLL apart from rw can do buf reg/unreg requests(
IORING_OP_PROVIDE_BUFFERS or IORING_OP_REMOVE_BUFFERS), so the fix is not
good.
Given that io_iopoll_complete() is always called under uring_lock, so here
for polled io, we can also get uring_lock to fix this issue.
Fixes: dad1b1242f ("io_uring: always let io_iopoll_complete() complete polled io")
Cc: <stable@vger.kernel.org> # 5.5+
Signed-off-by: Xiaoguang Wang <xiaoguang.wang@linux.alibaba.com>
Reviewed-by: Pavel Begunkov <asml.silence@gmail.com>
[axboe: don't deref 'req' after completing it']
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0020ef04e4 upstream.
For the first time a req punted to io-wq, we'll initialize io_wq_work's
list to be NULL, then insert req to io_wqe->work_list. If this req is not
inserted into tail of io_wqe->work_list, this req's io_wq_work list will
point to another req's io_wq_work. For splitted bio case, this req maybe
inserted to io_wqe->work_list repeatedly, once we insert it to tail of
io_wqe->work_list for the second time, now io_wq_work->list->next will be
invalid pointer, which then result in many strang error, panic, kernel
soft-lockup, rcu stall, etc.
In my vm, kernel doest not have commit cc29e1bf0d ("block: disable
iopoll for split bio"), below fio job can reproduce this bug steadily:
[global]
name=iouring-sqpoll-iopoll-1
ioengine=io_uring
iodepth=128
numjobs=1
thread
rw=randread
direct=1
registerfiles=1
hipri=1
bs=4m
size=100M
runtime=120
time_based
group_reporting
randrepeat=0
[device]
directory=/home/feiman.wxg/mntpoint/ # an ext4 mount point
If we have commit cc29e1bf0d ("block: disable iopoll for split bio"),
there will no splitted bio case for polled io, but I think we still to need
to fix this list corruption, it also should maybe go to stable branchs.
To fix this corruption, if a req is inserted into tail of io_wqe->work_list,
initialize req->io_wq_work->list->next to bu NULL.
Cc: stable@vger.kernel.org
Signed-off-by: Xiaoguang Wang <xiaoguang.wang@linux.alibaba.com>
Reviewed-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e469d0b09a upstream.
The gspca driver leaks memory when a probe fails. gspca_dev_probe2()
calls v4l2_device_register(), which takes a reference to the
underlying device node (in this case, a USB interface). But the
failure pathway neglects to call v4l2_device_unregister(), the routine
responsible for dropping this reference. Consequently the memory for
the USB interface and its device never gets released.
This patch adds the missing function call.
Reported-and-tested-by: syzbot+44e64397bd81d5e84cba@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d22f9a6c92 upstream.
We execute certain NPU2 setup code (such as mapping an LPID to a device
in NPU2) unconditionally if an Nvlink bridge is detected. However this
cannot succeed on POWER8NVL machines as the init helpers return an error
other than ENODEV which means the device is there is and setup failed so
vfio_pci_enable() fails and pass through is not possible.
This changes the two NPU2 related init helpers to return -ENODEV if
there is no "memory-region" device tree property as this is
the distinction between NPU and NPU2.
Tested on
- POWER9 pvr=004e1201, Ubuntu 19.04 host, Ubuntu 18.04 vm,
NVIDIA GV100 10de:1db1 driver 418.39
- POWER8 pvr=004c0100, RHEL 7.6 host, Ubuntu 16.10 vm,
NVIDIA P100 10de:15f9 driver 396.47
Fixes: 7f92891778 ("vfio_pci: Add NVIDIA GV100GL [Tesla V100 SXM2] subdriver")
Cc: stable@vger.kernel.org # 5.0
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 16b8fe4caf upstream.
In case an error occurs in vfio_pci_enable() before the call to
vfio_pci_probe_mmaps(), vfio_pci_disable() will try to iterate
on an uninitialized list and cause a kernel panic.
Lets move to the initialization to vfio_pci_probe() to fix the
issue.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Fixes: 05f0c03fba ("vfio-pci: Allow to mmap sub-page MMIO BARs if the mmio page is exclusive")
CC: Stable <stable@vger.kernel.org> # v4.7+
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 59850d226e upstream.
Checking !list_empty(&ctx->cq_overflow_list) around noflush in
io_cqring_events() is racy, because if it fails but a request overflowed
just after that, io_cqring_overflow_flush() still will be called.
Remove the second check, it shouldn't be a problem for performance,
because there is cq_check_overflow bit check just above.
Cc: <stable@vger.kernel.org> # 5.5+
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 14e3e989f6 ]
Since commit 36e2c7421f ("fs: don't allow splice read/write without
explicit ops") we've required that file operation structures explicitly
enable splice support, rather than falling back to the default handlers.
Most /proc files use the indirect 'struct proc_ops' to describe their
file operations, and were fixed up to support splice earlier in commits
40be821d627c..b24c30c67863, but the mountinfo files interact with the
VFS directly using their own 'struct file_operations' and got missed as
a result.
This adds the necessary support for splice to work for /proc/*/mountinfo
and friends.
Reported-by: Joan Bruguera Micó <joanbrugueram@gmail.com>
Reported-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209971
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 942cb357ae ]
Smack assumes that kernel threads are privileged for smackfs
operations. This was necessary because the credential of the
kernel thread was not related to a user operation. With io_uring
the credential does reflect a user's rights and can be used.
Suggested-by: Jens Axboe <axboe@kernel.dk>
Acked-by: Jens Axboe <axboe@kernel.dk>
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cda286f071 ]
io_uring_cancel_task_requests() doesn't imply that the ring is going
away, it may continue to work well after that. The problem is that it
sets ->cq_overflow_flushed effectively disabling the CQ overflow feature
Split setting cq_overflow_flushed from flush, and do the first one only
on exit. It's ok in terms of cancellations because there is a
io_uring->in_idle check in __io_cqring_fill_event().
It also fixes a race with setting ->cq_overflow_flushed in
io_uring_cancel_task_requests, whuch's is not atomic and a part of a
bitmask with other flags. Though, the only other flag that's not set
during init is drain_next, so it's not as bad for sane architectures.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Fixes: 0f2122045b ("io_uring: don't rely on weak ->files references")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 634578f800 ]
It's not safe to call io_cqring_overflow_flush() for IOPOLL mode without
hodling uring_lock, because it does synchronisation differently. Make
sure we have it.
As for io_ring_exit_work(), we don't even need it there because
io_ring_ctx_wait_and_kill() already set force flag making all overflowed
requests to be dropped.
Cc: <stable@vger.kernel.org> # 5.5+
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3cce9d4432 ]
Commit f77ac2e378 ("ARM: 9030/1: entry: omit FP emulation for UND
exceptions taken in kernel mode") failed to take into account that there
is in fact a case where we relied on this code path: during boot, the
VFP detection code issues a read of FPSID, which will trigger an undef
exception on cores that lack VFP support.
So let's reinstate this logic using an undef hook which is registered
only for the duration of the initcall to vpf_init(), and which sets
VFP_arch to a non-zero value - as before - if no VFP support is present.
Fixes: f77ac2e378 ("ARM: 9030/1: entry: omit FP emulation for UND ...")
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9014eab6a3 ]
It fixes this link warning:
WARNING: modpost: vmlinux.o(.text.unlikely+0x2d98): Section mismatch in reference from the function init_big_cores.isra.0() to the function .init.text:init_thread_group_cache_map()
The function init_big_cores.isra.0() references
the function __init init_thread_group_cache_map().
This is often because init_big_cores.isra.0 lacks a __init
annotation or the annotation of init_thread_group_cache_map is wrong.
Fixes: 425752c63b ("powerpc: Detect the presence of big-cores via "ibm, thread-groups"")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201221074154.403779-1-clg@kaod.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b36f835b63 ]
The lkp robot reported that some configs fail to build, for example
mpc85xx_smp_defconfig, with:
cc1: fatal error: opening output file arch/powerpc/boot/dts/fsl/.mpc8540ads.dtb.dts.tmp: No such file or directory
This bisects to:
cc8a51ca6f ("kbuild: always create directories of targets")
Although that commit claims to be about in-tree builds, it somehow
breaks out-of-tree builds. But presumably it's just exposing a latent
bug in our Makefiles.
We can fix it by adding to targets for dts/fsl in the same way that we
do for dts.
Fixes: cc8a51ca6f ("kbuild: always create directories of targets")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201215032906.473460-1-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 135b4957ea ]
$(error-if,...) is expanded to an empty string. Currently, it relies on
eval_clause() returning xstrdup("") when all attempts for expansion fail,
but the correct implementation is to make do_error_if() return xstrdup("").
Fixes: 1d6272e6fe ("kconfig: add 'info', 'warning-if', and 'error-if' built-in functions")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b003f5fca ]
Commit 45c940184b ("dt-bindings: clk: versaclock5: convert to
yaml") accidentally changed "idt,voltage-microvolts" to
"idt,voltage-microvolt" in the DT bindings, while the driver still used
the former.
Update the driver to match the bindings, as
Documentation/devicetree/bindings/property-units.txt actually recommends
using "microvolt".
Fixes: 260249f929 ("clk: vc5: Enable addition output configurations of the Versaclock")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201218125253.3815567-1-geert+renesas@glider.be
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 289caf5d8f ]
Patch series "simplify ep_poll".
This patch series is a followup based on the suggestions and feedback by
Linus:
https://lkml.kernel.org/r/CAHk-=wizk=OxUyQPbO8MS41w2Pag1kniUV5WdD5qWL-gq1kjDA@mail.gmail.com
The first patch in the series is a fix for the epoll race in presence of
timeouts, so that it can be cleanly backported to all affected stable
kernels.
The rest of the patch series simplify the ep_poll() implementation. Some
of these simplifications result in minor performance enhancements as well.
We have kept these changes under self tests and internal benchmarks for a
few days, and there are minor (1-2%) performance enhancements as a result.
This patch (of 8):
After abc610e01c ("fs/epoll: avoid barrier after an epoll_wait(2)
timeout"), we break out of the ep_poll loop upon timeout, without checking
whether there is any new events available. Prior to that patch-series we
always called ep_events_available() after exiting the loop.
This can cause races and missed wakeups. For example, consider the
following scenario reported by Guantao Liu:
Suppose we have an eventfd added using EPOLLET to an epollfd.
Thread 1: Sleeps for just below 5ms and then writes to an eventfd.
Thread 2: Calls epoll_wait with a timeout of 5 ms. If it sees an
event of the eventfd, it will write back on that fd.
Thread 3: Calls epoll_wait with a negative timeout.
Prior to abc610e01c, it is guaranteed that Thread 3 will wake up either
by Thread 1 or Thread 2. After abc610e01c, Thread 3 can be blocked
indefinitely if Thread 2 sees a timeout right before the write to the
eventfd by Thread 1. Thread 2 will be woken up from
schedule_hrtimeout_range and, with evail 0, it will not call
ep_send_events().
To fix this issue:
1) Simplify the timed_out case as suggested by Linus.
2) while holding the lock, recheck whether the thread was woken up
after its time out has reached.
Note that (2) is different from Linus' original suggestion: It do not set
"eavail = ep_events_available(ep)" to avoid unnecessary contention (when
there are too many timed-out threads and a small number of events), as
well as races mentioned in the discussion thread.
This is the first patch in the series so that the backport to stable
releases is straightforward.
Link: https://lkml.kernel.org/r/20201106231635.3528496-1-soheil.kdev@gmail.com
Link: https://lkml.kernel.org/r/CAHk-=wizk=OxUyQPbO8MS41w2Pag1kniUV5WdD5qWL-gq1kjDA@mail.gmail.com
Link: https://lkml.kernel.org/r/20201106231635.3528496-2-soheil.kdev@gmail.com
Fixes: abc610e01c ("fs/epoll: avoid barrier after an epoll_wait(2) timeout")
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Tested-by: Guantao Liu <guantaol@google.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Guantao Liu <guantaol@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Khazhismel Kumykov <khazhy@google.com>
Reviewed-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 83ef73b27e ]
Make sure to put dma write memory barrier after updating CQ consumer
index so the hardware knows that there are available CQE slots in the
queue.
Failure to do this can cause the update of the RX doorbell record to get
updated before the CQ consumer index resulting in CQ overrun.
Fixes: 1a86b377aa ("vdpa/mlx5: Add VDPA driver for supported mlx5 devices")
Signed-off-by: Eli Cohen <elic@nvidia.com>
Link: https://lore.kernel.org/r/20201209140004.15892-1-elic@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5b33afee93 ]
The indirect block cleanup may cause control messages to be sent
if offloaded flows are present. However, by the time the flower app
cleanup callback is called txbufs are no longer available and attempts
to send control messages result in a NULL-pointer dereference in
nfp_ctrl_tx_one().
This problem may be resolved by moving the indirect block cleanup
to the stop callback, where txbufs are still available.
As suggested by Jakub Kicinski and Louis Peens.
Fixes: a1db217861 ("net: flow_offload: fix flow_indr_dev_unregister path")
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Louis Peens <louis.peens@netronome.com>
Link: https://lore.kernel.org/r/20201216145701.30005-1-simon.horman@netronome.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09d59c2f34 ]
We're missing -lcap in test-all.bin target, so in case it's the only
library missing (if more are missing test-all.bin fails anyway), we will
falsely claim that we detected it and fail build, like:
$ make
...
Auto-detecting system features:
... dwarf: [ on ]
... dwarf_getlocations: [ on ]
... glibc: [ on ]
... libbfd: [ on ]
... libbfd-buildid: [ on ]
... libcap: [ on ]
... libelf: [ on ]
... libnuma: [ on ]
... numa_num_possible_cpus: [ on ]
... libperl: [ on ]
... libpython: [ on ]
... libcrypto: [ on ]
... libunwind: [ on ]
... libdw-dwarf-unwind: [ on ]
... zlib: [ on ]
... lzma: [ on ]
... get_cpuid: [ on ]
... bpf: [ on ]
... libaio: [ on ]
... libzstd: [ on ]
... disassembler-four-args: [ on ]
...
CC builtin-ftrace.o
In file included from builtin-ftrace.c:29:
util/cap.h:11:10: fatal error: sys/capability.h: No such file or directory
11 | #include <sys/capability.h>
| ^~~~~~~~~~~~~~~~~~
compilation terminated.
Fixes: 74d5f3d06f ("tools build: Add capability-related feature detection")
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Igor Lubashev <ilubashe@akamai.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lore.kernel.org/lkml/20201203230836.3751981-1-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df9923f967 ]
io_uring_cancel_files() cancels all request that match files regardless
of task. There is no real need in that, cancel only requests of the
specified task. That also handles SQPOLL case as it already changes task
to it.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6eefb79d6f ]
Commit d3817a6470 ("pwm: sun4i: Remove redundant needs_delay") changed
the logic of an else branch so that the PWM_EN and PWM_CLK_GATING bits
are now cleared if the PWM is to be disabled, whereas previously the
condition was always false, and hence the branch never got executed.
This code is reported causing backlight issues on boards based on the
Allwinner A20 SoC. Fix this by removing the else branch, which restores
the behaviour prior to the offending commit.
Note that the PWM_EN and PWM_CLK_GATING bits still get cleared later in
sun4i_pwm_apply() if the PWM is to be disabled.
Fixes: d3817a6470 ("pwm: sun4i: Remove redundant needs_delay")
Reported-by: Taras Galchenko <tpgalchenko@gmail.com>
Suggested-by: Taras Galchenko <tpgalchenko@gmail.com>
Tested-by: Taras Galchenko <tpgalchenko@gmail.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ce65396e6 ]
The second parameter of do_div is an u32 and NSEC_PER_SEC * prescale
overflows this for bigger periods. Assuming the usual pwm input clk rate
of 66 MHz this happens starting at requested period > 606060 ns.
Splitting the division into two operations doesn't loose any precision.
It doesn't need to be feared that c / NSEC_PER_SEC doesn't fit into the
unsigned long variable "duty_cycles" because in this case the assignment
above to period_cycles would already have been overflowing as
period >= duty_cycle and then the calculation is moot anyhow.
Fixes: aef1a3799b ("pwm: imx27: Fix rounding behavior")
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Tested-by: Johannes Pointner <johannes.pointner@br-automation.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1f0f1e80fd ]
When there are other PWM controllers enabled along with pwm-lp3943,
pwm-lp3942 is failing to probe with -EEXIST error. This is because
other PWM controllers are probed first and assigned PWM base 0 and
pwm-lp3943 is requesting for 0 again.
In order to avoid this, assign the chip base with -1, so that it is
dynamically allocated.
Fixes: af66b3c093 ("pwm: Add LP3943 PWM driver")
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Uwe Kleine-König <u.kleine-könig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 36c47df85e ]
clang produces a build failure in configurations without COMMON_CLK
when a timeout calculation goes wrong:
arm-linux-gnueabi-ld: drivers/watchdog/coh901327_wdt.o: in function `coh901327_enable':
coh901327_wdt.c:(.text+0x50): undefined reference to `__bad_udelay'
Add a Kconfig dependency to only do build testing when COMMON_CLK
is enabled.
Fixes: da2a68b3eb ("watchdog: Enable COMPILE_TEST where possible")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20201203223358.1269372-1-arnd@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1bea0a840 ]
Currently pmac32_defconfig with SMP=y doesn't build:
arch/powerpc/platforms/powermac/smp.c:
error: implicit declaration of function 'cleanup_cpu_mmu_context'
It would be nice for consistency if all platforms clear mm_cpumask and
flush TLBs on unplug, but the TLB invalidation bug described in commit
01b0f0eae0 ("powerpc/64s: Trim offlined CPUs from mm_cpumasks") only
applies to 64s and for now we only have the TLB flush code for that
platform.
So just add an empty version for 32-bit Book3S.
Fixes: 01b0f0eae0 ("powerpc/64s: Trim offlined CPUs from mm_cpumasks")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Change log based on comments from Nick]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46067844ef ]
In error case, we do not free the memory for blk_symlink_name.
Do it by free the memory in error case, and set to NULL
afterwards.
Also fix the condition in rnbd_clt_remove_dev_symlink.
Fixes: 64e8a6ece1 ("block/rnbd-clt: Dynamically alloc buffer for pathname & blk_symlink_name")
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Reviewed-by: Md Haris Iqbal <haris.iqbal@cloud.ionos.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e7508d4856 ]
The kernel test robot triggerred the following warning,
>> drivers/block/rnbd/rnbd-clt.c:1397:42: warning: size argument in
'strlcpy' call appears to be size of the source; expected the size of the
destination [-Wstrlcpy-strlcat-size]
strlcpy(dev->pathname, pathname, strlen(pathname) + 1);
~~~~~~~^~~~~~~~~~~~~
To get rid of the above warning, use a kstrdup as Bart suggested.
Fixes: 64e8a6ece1 ("block/rnbd-clt: Dynamically alloc buffer for pathname & blk_symlink_name")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Md Haris Iqbal <haris.iqbal@cloud.ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 54a57d1c44 ]
This patch fixes an error condition triggered when the code path which
transmits a S/G frame descriptor when the skb's headroom is not enough
for DPAA2's needs.
We are greated with a splat like the one below when a SGT structure is
recycled and that is because even though a dma_unmap is performed on the
Tx confirmation path, the unmap is not done with the proper size.
[ 714.464927] WARNING: CPU: 13 PID: 0 at drivers/iommu/io-pgtable-arm.c:281 __arm_lpae_map+0x2d4/0x30c
(...)
[ 714.465343] Call trace:
[ 714.465348] __arm_lpae_map+0x2d4/0x30c
[ 714.465353] __arm_lpae_map+0x114/0x30c
[ 714.465357] __arm_lpae_map+0x114/0x30c
[ 714.465362] __arm_lpae_map+0x114/0x30c
[ 714.465366] arm_lpae_map+0xf4/0x180
[ 714.465373] arm_smmu_map+0x4c/0xc0
[ 714.465379] __iommu_map+0x100/0x2bc
[ 714.465385] iommu_map_atomic+0x20/0x30
[ 714.465391] __iommu_dma_map+0xb0/0x110
[ 714.465397] iommu_dma_map_page+0xb8/0x120
[ 714.465404] dma_map_page_attrs+0x1a8/0x210
[ 714.465413] __dpaa2_eth_tx+0x384/0xbd0 [fsl_dpaa2_eth]
[ 714.465421] dpaa2_eth_tx+0x84/0x134 [fsl_dpaa2_eth]
[ 714.465427] dev_hard_start_xmit+0x10c/0x2b0
[ 714.465433] sch_direct_xmit+0x1a0/0x550
(...)
The dpaa2-eth driver uses an area of software annotations to transmit
necessary information from the Tx path to the Tx confirmation one. This
SWA structure has a different layout for each kind of frame that we are
dealing with: linear, S/G or XDP.
The commit referenced was incorrectly setting up the 'sgt_size' field
for the S/G type of SWA even though we are dealing with a linear skb
here.
Fixes: d70446ee1f ("dpaa2-eth: send a scatter-gather FD instead of realloc-ing")
Reported-by: Daniel Thompson <daniel.thompson@linaro.org>
Tested-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/20201211171607.108034-1-ciorneiioana@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 64050b5b87 ]
On the Rx side, the next_to_use index points to the next item in the
HW ring to be refilled/allocated, and next_to_clean points to the next
item to potentially be processed.
When the HW Rx ring is fully refilled, i.e. no packets has been
processed, the next_to_use will be next_to_clean - 1. When the ring is
fully processed next_to_clean will be equal to next_to_use. The latter
case is where a bug is triggered.
If the next_to_use bits are not cleared, and the "fully processed"
state is entered, a stale descriptor can be processed.
The skb-path correctly clear the status bit for the next_to_use
descriptor, but the AF_XDP zero-copy path did not do that.
This change adds the status bits clearing of the next_to_use
descriptor.
Fixes: 3b4f0b66c2 ("i40e, xsk: Migrate to new MEM_TYPE_XSK_BUFF_POOL")
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d14768a79 ]
On the Rx side, the next_to_use index points to the next item in the
HW ring to be refilled/allocated, and next_to_clean points to the next
item to potentially be processed.
When the HW Rx ring is fully refilled, i.e. no packets has been
processed, the next_to_use will be next_to_clean - 1. When the ring is
fully processed next_to_clean will be equal to next_to_use. The latter
case is where a bug is triggered.
If the next_to_use bits are not cleared, and the "fully processed"
state is entered, a stale descriptor can be processed.
The skb-path correctly clear the status bit for the next_to_use
descriptor, but the AF_XDP zero-copy path did not do that.
This change adds the status bits clearing of the next_to_use
descriptor.
Fixes: 2d4238f556 ("ice: Add support for AF_XDP")
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 57030a0b62 ]
Even if there is more rx data waiting on the chip, the rx napi poll fn
will never run more than once - it will always read a few buffers, then
bail out and re-arm interrupts. Which results in ping-pong between napi
and interrupt.
This defeats the purpose of napi, and is bad for performance.
Fix by making the rx napi poll behave identically to other ethernet
drivers:
1. initialize rx napi polling with an arbitrary budget (64).
2. in the polling fn, return full weight if rx queue is not depleted,
this tells the napi core to "keep polling".
3. update the rx tail ("ring the doorbell") once for every 8 processed
rx ring buffers.
Thanks to Jakub Kicinski, Eric Dumazet and Andrew Lunn for their expert
opinions and suggestions.
Tested with 20 seconds of full bandwidth receive (iperf3):
rx irqs softirqs(NET_RX)
-----------------------------
before 23827 33620
after 129 4081
Tested-by: Sven Van Asbroeck <thesven73@gmail.com> # lan7430
Fixes: 23f0703c12 ("lan743x: Add main source files for new lan743x driver")
Signed-off-by: Sven Van Asbroeck <thesven73@gmail.com>
Link: https://lore.kernel.org/r/20201215161954.5950-1-TheSven73@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f22b9c219a ]
The CALL_ON_STACK tests use the no_dat stack to switch to a different
stack for unwinding tests. If an interrupt or machine check happens
while using that stack, and previously being on the async stack, the
interrupt / machine check entry code (SWITCH_ASYNC) will assume that
the previous context did not use the async stack and happily use the
async stack again.
This will lead to stack corruption of the previous context.
To solve this disable both interrupts and machine checks before
switching to the no_dat stack.
Fixes: 7868249fbb ("s390/test_unwind: add CALL_ON_STACK tests")
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c6c75deda8 ]
Commit 1fde6f21d9 ("proc: fix /proc/net/* after setns(2)") only forced
revalidation of regular files under /proc/net/
However, /proc/net/ is unusual in the sense of /proc/net/foo handlers
take netns pointer from parent directory which is old netns.
Steps to reproduce:
(void)open("/proc/net/sctp/snmp", O_RDONLY);
unshare(CLONE_NEWNET);
int fd = open("/proc/net/sctp/snmp", O_RDONLY);
read(fd, &c, 1);
Read will read wrong data from original netns.
Patch forces lookup on every directory under /proc/net .
Link: https://lkml.kernel.org/r/20201205160916.GA109739@localhost.localdomain
Fixes: 1da4d377f9 ("proc: revalidate misc dentries")
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Reported-by: "Rantala, Tommi T. (Nokia - FI/Espoo)" <tommi.t.rantala@nokia.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 597c892038 ]
On 2-node NUMA hosts we see bursts of kswapd reclaim and subsequent
pressure spikes and stalls from cache refaults while there is plenty of
free memory in the system.
Usually, kswapd is woken up when all eligible nodes in an allocation are
full. But the code related to watermark boosting can wake kswapd on one
full node while the other one is mostly empty. This may be justified to
fight fragmentation, but is currently unconditionally done whether
watermark boosting is occurring or not.
In our case, many of our workloads' throughput scales with available
memory, and pure utilization is a more tangible concern than trends
around longer-term fragmentation. As a result we generally disable
watermark boosting.
Wake kswapd only woken when watermark boosting is requested.
Link: https://lkml.kernel.org/r/20201020175833.397286-1-hannes@cmpxchg.org
Fixes: 1c30844d2d ("mm: reclaim small amounts of memory when an external fragmentation event occurs")
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e8aaedb18 ]
madvise_inject_error() uses get_user_pages_fast to translate the address
we specified to a page. After [1], we drop the extra reference count for
memory_failure() path. That commit says that memory_failure wanted to
keep the pin in order to take the page out of circulation.
The truth is that we need to keep the page pinned, otherwise the page
might be re-used after the put_page() and we can end up messing with
someone else's memory.
E.g:
CPU0
process X CPU1
madvise_inject_error
get_user_pages
put_page
page gets reclaimed
process Y allocates the page
memory_failure
// We mess with process Y memory
madvise() is meant to operate on a self address space, so messing with
pages that do not belong to us seems the wrong thing to do.
To avoid that, let us keep the page pinned for memory_failure as well.
Pages for DAX mappings will release this extra refcount in
memory_failure_dev_pagemap.
[1] ("23e7b5c2e271: mm, madvise_inject_error:
Let memory_failure() optionally take a page reference")
Link: https://lkml.kernel.org/r/20201207094818.8518-1-osalvador@suse.de
Fixes: 23e7b5c2e2 ("mm, madvise_inject_error: Let memory_failure() optionally take a page reference")
Signed-off-by: Oscar Salvador <osalvador@suse.de>
Suggested-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Naoya Horiguchi <naoya.horiguchi@nec.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c041098c69 ]
The size of vm area can be affected by the presence or not of the guard
page. In particular when VM_NO_GUARD is present, the actual accessible
size has to be considered like the real size minus the guard page.
Currently kasan does not keep into account this information during the
poison operation and in particular tries to poison the guard page as well.
This approach, even if incorrect, does not cause an issue because the tags
for the guard page are written in the shadow memory. With the future
introduction of the Tag-Based KASAN, being the guard page inaccessible by
nature, the write tag operation on this page triggers a fault.
Fix kasan shadow poisoning size invoking get_vm_area_size() instead of
accessing directly the field in the data structure to detect the correct
value.
Link: https://lkml.kernel.org/r/20201027160213.32904-1-vincenzo.frascino@arm.com
Fixes: d98c9e83b5 ("kasan: fix crashes on access to memory mapped by vm_map_ram()")
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: Andrey Konovalov <andreyknvl@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Marco Elver <elver@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a7dd4e901 ]
When multiple locks are acquired, they should be released in reverse
order. For s_start() and s_stop() in mm/vmalloc.c, that is not the
case.
s_start: mutex_lock(&vmap_purge_lock); spin_lock(&vmap_area_lock);
s_stop : mutex_unlock(&vmap_purge_lock); spin_unlock(&vmap_area_lock);
This unlock sequence, though allowed, is not optimal. If a waiter is
present, mutex_unlock() will need to go through the slowpath of waking
up the waiter with preemption disabled. Fix that by releasing the
spinlock first before the mutex.
Link: https://lkml.kernel.org/r/20201213180843.16938-1-longman@redhat.com
Fixes: e36176be1c ("mm/vmalloc: rework vmap_area_lock")
Signed-off-by: Waiman Long <longman@redhat.com>
Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 013339df11 ]
Since commit 369ea8242c ("mm/rmap: update to new mmu_notifier semantic
v2"), the code to check the secondary MMU's page table access bit is
broken for !(TTU_IGNORE_ACCESS) because the page is unmapped from the
secondary MMU's page table before the check. More specifically for those
secondary MMUs which unmap the memory in
mmu_notifier_invalidate_range_start() like kvm.
However memory reclaim is the only user of !(TTU_IGNORE_ACCESS) or the
absence of TTU_IGNORE_ACCESS and it explicitly performs the page table
access check before trying to unmap the page. So, at worst the reclaim
will miss accesses in a very short window if we remove page table access
check in unmapping code.
There is an unintented consequence of !(TTU_IGNORE_ACCESS) for the memcg
reclaim. From memcg reclaim the page_referenced() only account the
accesses from the processes which are in the same memcg of the target page
but the unmapping code is considering accesses from all the processes, so,
decreasing the effectiveness of memcg reclaim.
The simplest solution is to always assume TTU_IGNORE_ACCESS in unmapping
code.
Link: https://lkml.kernel.org/r/20201104231928.1494083-1-shakeelb@google.com
Fixes: 369ea8242c ("mm/rmap: update to new mmu_notifier semantic v2")
Signed-off-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 57efa1fe59 ]
Since commit 70e806e4e6 ("mm: Do early cow for pinned pages during
fork() for ptes") pages under a FOLL_PIN will not be write protected
during COW for fork. This means that pages returned from
pin_user_pages(FOLL_WRITE) should not become write protected while the pin
is active.
However, there is a small race where get_user_pages_fast(FOLL_PIN) can
establish a FOLL_PIN at the same time copy_present_page() is write
protecting it:
CPU 0 CPU 1
get_user_pages_fast()
internal_get_user_pages_fast()
copy_page_range()
pte_alloc_map_lock()
copy_present_page()
atomic_read(has_pinned) == 0
page_maybe_dma_pinned() == false
atomic_set(has_pinned, 1);
gup_pgd_range()
gup_pte_range()
pte_t pte = gup_get_pte(ptep)
pte_access_permitted(pte)
try_grab_compound_head()
pte = pte_wrprotect(pte)
set_pte_at();
pte_unmap_unlock()
// GUP now returns with a write protected page
The first attempt to resolve this by using the write protect caused
problems (and was missing a barrrier), see commit f3c64eda3e ("mm: avoid
early COW write protect games during fork()")
Instead wrap copy_p4d_range() with the write side of a seqcount and check
the read side around gup_pgd_range(). If there is a collision then
get_user_pages_fast() fails and falls back to slow GUP.
Slow GUP is safe against this race because copy_page_range() is only
called while holding the exclusive side of the mmap_lock on the src
mm_struct.
[akpm@linux-foundation.org: coding style fixes]
Link: https://lore.kernel.org/r/CAHk-=wi=iCnYCARbPGjkVJu9eyYeZ13N64tZYLdOB8CP5Q_PLw@mail.gmail.com
Link: https://lkml.kernel.org/r/2-v4-908497cf359a+4782-gup_fork_jgg@nvidia.com
Fixes: f3c64eda3e ("mm: avoid early COW write protect games during fork()")
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Reviewed-by: John Hubbard <jhubbard@nvidia.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Peter Xu <peterx@redhat.com>
Acked-by: "Ahmed S. Darwish" <a.darwish@linutronix.de> [seqcount_t parts]
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.ibm.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: Jann Horn <jannh@google.com>
Cc: Kirill Shutemov <kirill@shutemov.name>
Cc: Kirill Tkhai <ktkhai@virtuozzo.com>
Cc: Leon Romanovsky <leonro@nvidia.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c28b1fc703 ]
Patch series "Add a seqcount between gup_fast and copy_page_range()", v4.
As discussed and suggested by Linus use a seqcount to close the small race
between gup_fast and copy_page_range().
Ahmed confirms that raw_write_seqcount_begin() is the correct API to use
in this case and it doesn't trigger any lockdeps.
I was able to test it using two threads, one forking and the other using
ibv_reg_mr() to trigger GUP fast. Modifying copy_page_range() to sleep
made the window large enough to reliably hit to test the logic.
This patch (of 2):
The next patch in this series makes the lockless flow a little more
complex, so move the entire block into a new function and remove a level
of indention. Tidy a bit of cruft:
- addr is always the same as start, so use start
- Use the modern check_add_overflow() for computing end = start + len
- nr_pinned/pages << PAGE_SHIFT needs the LHS to be unsigned long to
avoid shift overflow, make the variables unsigned long to avoid coding
casts in both places. nr_pinned was missing its cast
- The handling of ret and nr_pinned can be streamlined a bit
No functional change.
Link: https://lkml.kernel.org/r/0-v4-908497cf359a+4782-gup_fork_jgg@nvidia.com
Link: https://lkml.kernel.org/r/1-v4-908497cf359a+4782-gup_fork_jgg@nvidia.com
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: John Hubbard <jhubbard@nvidia.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7eded018bf ]
We need to move the check under the non-headless case, otherwise
we always reserve the VGA save size.
Fixes: 157fe68d74 ("drm/amdgpu: fix size calculation with stolen vga memory")
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2ce5dbc15 ]
Commit e1c92a7fbb ("perf tests: Add another metric parsing test") add
another test for metric parsing. The test goes through all metrics
compiled for arch within pmu events and try to parse them.
Right now this test is failing in powerpc machine.
Result in power9 platform:
[command]# ./perf test 10
10: PMU events :
10.1: PMU event table sanity : Ok
10.2: PMU event map aliases : Ok
10.3: Parsing of PMU event table metrics : Skip (some metrics failed)
10.4: Parsing of PMU event table metrics with fake PMUs : FAILED!
Issue is we are passing different runtime parameter value in
"expr__find_other" and "expr__parse" function which is called from
function `metric_parse_fake`. And because of this parsing of hv-24x7
metrics is failing.
[command]# ./perf test 10 -vv
.....
hv_24x7/pm_mcs01_128b_rd_disp_port01,chip=1/ not found
expr__parse failed
test child finished with -1
---- end ----
PMU events subtest 4: FAILED!
This patch fix this issue and change runtime parameter value to '0' in
expr__parse function.
Result in power9 platform after this patch:
[command]# ./perf test 10
10: PMU events :
10.1: PMU event table sanity : Ok
10.2: PMU event map aliases : Ok
10.3: Parsing of PMU event table metrics : Skip (some metrics failed)
10.4: Parsing of PMU event table metrics with fake PMUs : Ok
Fixes: e1c92a7fbb ("perf tests: Add another metric parsing test")
Signed-off-by: Kajol Jain <kjain@linux.ibm.com>
Acked-by: Ian Rogers <irogers@google.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Madhavan Srinivasan <maddy@linux.ibm.com>
Cc: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Link: http://lore.kernel.org/lkml/20201119152411.46041-1-kjain@linux.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef0e3b650f ]
Threshold Event Counter Multiplier (TECM) is part of Monitor Mode
Control Register A (MMCRA). This field along with Threshold Event
Counter Exponent (TECE) is used to get threshould counter value.
In Power10, this is a 8bit field, so patch fixes the
current code to modify the MMCRA[TECM] extraction macro to
handle this change. ISA v3.1 says this is a 7 bit field but
POWER10 it's actually 8 bits which will hopefully be fixed
in ISA v3.1 update.
Fixes: 170a315f41 ("powerpc/perf: Support to export MMCRA[TEC*] field to userspace")
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Signed-off-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1608022578-1532-1-git-send-email-atrajeev@linux.vnet.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee46d16d2e ]
It can take multiple iterations until all components for an attached DSI
bridge are up leading to several:
[ 3.796425] mxsfb 30320000.lcd-controller: Cannot connect bridge: -517
[ 3.816952] mxsfb 30320000.lcd-controller: [drm:mxsfb_probe [mxsfb]] *ERROR* failed to attach bridge: -517
Silence this by checking for -EPROBE_DEFER and using dev_err_probe() so
we set a deferred reason in case a dependency fails to probe (which
quickly happens on small config/DT changes due to the rather long probe
chain which can include bridges, phys, panels, backights, leds, etc.).
This also removes the only DRM_DEV_ERROR() usage, the rest of the driver
uses dev_err().
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Fixes: c42001e357 ("drm: mxsfb: Use drm_panel_bridge")
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/d5761eb871adde5464ba112b89d966568bc2ff6c.1608020391.git.agx@sigxcpu.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e899389029 ]
If the MR cache entry invalidation failed, then we detach this entry from
the cache, therefore we must to free the memory as well.
Allcation backtrace for the leaker:
[<00000000d8e423b0>] alloc_cache_mr+0x23/0xc0 [mlx5_ib]
[<000000001f21304c>] create_cache_mr+0x3f/0xf0 [mlx5_ib]
[<000000009d6b45dc>] mlx5_ib_alloc_implicit_mr+0x41/0×210 [mlx5_ib]
[<00000000879d0d68>] mlx5_ib_reg_user_mr+0x9e/0×6e0 [mlx5_ib]
[<00000000be74bf89>] create_qp+0x2fc/0xf00 [ib_uverbs]
[<000000001a532d22>] ib_uverbs_handler_UVERBS_METHOD_COUNTERS_READ+0x1d9/0×230 [ib_uverbs]
[<0000000070f46001>] rdma_alloc_commit_uobject+0xb5/0×120 [ib_uverbs]
[<000000006d8a0b38>] uverbs_alloc+0x2b/0xf0 [ib_uverbs]
[<00000000075217c9>] ksysioctl+0x234/0×7d0
[<00000000eb5c120b>] __x64_sys_ioctl+0x16/0×20
[<00000000db135b48>] do_syscall_64+0x59/0×2e0
Fixes: 1769c4c575 ("RDMA/mlx5: Always remove MRs from the cache before destroying them")
Link: https://lore.kernel.org/r/20201213132940.345554-2-leon@kernel.org
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac9645c873 ]
When receiving pages data, return value 'ret' when positive includes
`buf->page_base`, so we should subtract that before it is used for
changing `offset` and comparing against `want`.
This was discovered on the very rare cases where the server returned a
chunk of bytes that when added to the already received amount of bytes
for the pages happened to match the current `recv.len`, for example
on this case:
buf->page_base : 258356
actually received from socket: 1740
ret : 260096
want : 260096
In this case neither of the two 'if ... goto out' trigger, and we
continue to tail parsing.
Worth to mention that the ensuing EMSGSIZE from the continued execution of
`xs_read_xdr_buf` may be observed by an application due to 4 superfluous
bytes being added to the pages data.
Fixes: 277e4ab7d5 ("SUNRPC: Simplify TCP receive code by switching to using iterators")
Signed-off-by: Dan Aloni <dan@kernelim.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9431f7c199 ]
xterm serial channel was leaking a fd used in setting up the
port helper
This bug is prehistoric - it predates switching to git. The "fixes"
header here is really just to mark all the versions we would like this to
apply to which is "Anything from the Cretaceous period onwards".
No dinosaurs were harmed in fixing this bug.
Fixes: b40997b872 ("um: drivers/xterm.c: fix a file descriptor leak")
Signed-off-by: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b1c0c0e25 ]
Fix a logical error in tty reading. We get 0 and errno == EAGAIN
on the first attempt to read from a closed file descriptor.
Compared to that a true EAGAIN is EAGAIN and -1.
If we check errno for EAGAIN first, before checking the return
value we miss the fact that the descriptor is closed.
This bug is as old as the driver. It was not showing up with
the original POLL based IRQ controller, because it was
producing multiple events. Switching to EPOLL unmasked it.
Fixes: ff6a17989c ("Epoll based IRQ controller")
Signed-off-by: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3a01cbee9 ]
Ensure that file closes, connection closes, etc are propagated
as interrupts in the interrupt controller.
Fixes: ff6a17989c ("Epoll based IRQ controller")
Signed-off-by: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3cded66330 ]
Fix to return PTR_ERR() error code from the error handling case where
ubifs_hash_get_desc() failed instead of 0 in ubifs_init_authentication(),
as done elsewhere in this function.
Fixes: 49525e5eec ("ubifs: Add helper functions for authentication support")
Signed-off-by: Wang ShaoBo <bobo.shaobowang@huawei.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f733cb2e7 ]
A reboot notifier, which stops the WDT by calling the stop hook without
any check, would be registered when we set WDOG_STOP_ON_REBOOT flag.
Howerer we allow the WDT driver to omit the stop hook since commit
"d0684c8a93549" ("watchdog: Make stop function optional") and provide
a module parameter for user that controls the WDOG_STOP_ON_REBOOT flag
in commit 9232c80659 ("watchdog: Add stop_on_reboot parameter to
control reboot policy"). Together that commits make user potential to
insert a watchdog driver that don't provide a stop hook but with the
stop_on_reboot parameter set, then dereferencing of null pointer occurs
on system reboot.
Check the stop hook before registering the reboot notifier to fix the
issue.
Fixes: d0684c8a93 ("watchdog: Make stop function optional")
Signed-off-by: Wang Wensheng <wangwensheng4@huawei.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20201109130512.28121-1-wangwensheng4@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f6f1dfb2d ]
The following kbuild warning is seen on a system without HAS_IOMEM.
WARNING: unmet direct dependencies detected for MFD_SYSCON
Depends on [n]: HAS_IOMEM [=n]
Selected by [y]:
- ARMADA_37XX_WATCHDOG [=y] && WATCHDOG [=y] && (ARCH_MVEBU || COMPILE_TEST
This results in a subsequent compile error.
drivers/watchdog/armada_37xx_wdt.o: in function `armada_37xx_wdt_probe':
armada_37xx_wdt.c:(.text+0xdc): undefined reference to `devm_ioremap'
Add the missing dependency.
Reported-by: Necip Fazil Yildiran <fazilyildiran@gmail.com>
Fixes: 54e3d9b518 ("watchdog: Add support for Armada 37xx CPU watchdog")
Link: https://lore.kernel.org/r/20201108162550.27660-1-linux@roeck-us.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f5fbc4305 ]
We have a problem if we use gpio-keys and configure wakeups such that
we only want one edge to wake us up. AKA:
wakeup-event-action = <EV_ACT_DEASSERTED>;
wakeup-source;
Specifically we end up with a phantom interrupt that blocks suspend if
the line was already high and we want wakeups on rising edges (AKA we
want the GPIO to go low and then high again before we wake up). The
opposite is also problematic.
Specifically, here's what's happening today:
1. Normally, gpio-keys configures to look for both edges. Due to the
current workaround introduced in commit c3c0c2e18d ("pinctrl:
qcom: Handle broken/missing PDC dual edge IRQs on sc7180"), if the
line was high we'd configure for falling edges.
2. At suspend time, we change to look for rising edges.
3. After qcom_pdc_gic_set_type() runs, we get a phantom interrupt.
We can solve this by just clearing the phantom interrupt.
NOTE: it is possible that this could cause problems for a client with
very specific needs, but there's not much we can do with this
hardware. As an example, let's say the interrupt signal is currently
high and the client is looking for falling edges. The client now
changes to look for rising edges. The client could possibly expect
that if the line has a short pulse low (and back high) that it would
always be detected. Specifically no matter when the pulse happened,
it should either have tripped the (old) falling edge trigger or the
(new) rising edge trigger. We will simply not trip it. We could
narrow down the race a bit by polling our parent before changing
types, but no matter what we do there will still be a period of time
where we can't tell the difference between a real transition (or more
than one transition) and the phantom.
Fixes: f55c73aef8 ("irqchip/pdc: Add PDC interrupt controller for QCOM SoCs")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Tested-by: Maulik Shah <mkshah@codeaurora.org>
Reviewed-by: Maulik Shah <mkshah@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20201211141514.v4.1.I2702919afc253e2a451bebc3b701b462b2d22344@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d55221995 ]
irqchip shared with multiple gpiochips, leads to recursive call of
gpiochip_irq_mask/gpiochip_irq_unmask which was assigned to
rqchip->irq_mask/irqchip->irq_unmask, these happens becouse of
only irqchip->irq_enable == gpiochip_irq_enable is checked.
Let's add an additional check to make sure shared irqchip is detected
even if irqchip->irq_enable wasn't defined.
Fixes: a8173820f4 ("gpio: gpiolib: Allow GPIO IRQs to lazy disable")
Signed-off-by: Nikita Shubin <nikita.shubin@maquefel.me>
Link: https://lore.kernel.org/r/20201210070514.13238-1-nikita.shubin@maquefel.me
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c0ca9cd17 ]
For ib_copy_from_user(), the length of udata may not be the same as that
of cmd. For ib_copy_to_user(), the length of udata may not be the same as
that of resp. So limit the length to prevent out-of-bounds read and write
operations from ib_copy_from_user() and ib_copy_to_user().
Fixes: de77503a59 ("RDMA/hns: RDMA/hns: Assign rq head pointer when enable rq record db")
Fixes: 633fb4d9fd ("RDMA/hns: Use structs to describe the uABI instead of opencoding")
Fixes: ae85bf92ef ("RDMA/hns: Optimize qp param setup flow")
Fixes: 6fd610c573 ("RDMA/hns: Support 0 hop addressing for SRQ buffer")
Fixes: 9d9d4ff788 ("RDMA/hns: Update the kernel header file of hns")
Link: https://lore.kernel.org/r/1607650657-35992-2-git-send-email-liweihang@huawei.com
Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc6c7cd387 ]
ti_sci_intr_irq_domain_free() assumes that out_irq of intr is stored in
data->chip_data and uses it for calling ti_sci irq_free() and then
mark the out_irq as available resource. But ti_sci_intr_irq_domain_alloc()
is storing p_hwirq(parent's hardware irq) which is translated from out_irq.
This is causing resource leakage and eventually out_irq resources might
be exhausted. Fix ti_sci_intr_irq_domain_alloc() by storing the out_irq
in data->chip_data.
Fixes: a5b659bd4b ("irqchip/ti-sci-intr: Add support for INTR being a parent to INTR")
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20201102120631.11165-1-lokeshvutla@ti.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f65607cdbc ]
When we set up a TDLS station, we set sta->sta.bandwidth solely based
on the capabilities, because the "what's the current bandwidth" check
is bypassed and only applied for other types of stations.
This leads to the unfortunate scenario that the sta->sta.bandwidth is
160 MHz if both stations support it, but we never actually configure
this bandwidth unless the AP is already using 160 MHz; even for wider
bandwidth support we only go up to 80 MHz (at least right now.)
For iwlwifi, this can also lead to firmware asserts, telling us that
we've configured the TX rates for a higher bandwidth than is actually
available due to the PHY configuration.
For non-TDLS, we check against the interface's requested bandwidth,
but we explicitly skip this check for TDLS to cope with the wider BW
case. Change this to
(a) still limit to the TDLS peer's own chandef, which gets factored
into the overall PHY configuration we request from the driver,
and
(b) limit it to when the TDLS peer is authorized, because it's only
factored into the channel context in this case.
Fixes: 504871e602 ("mac80211: fix bandwidth computation for TDLS peers")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201206145305.fcc7d29c4590.I11f77e9e25ddf871a3c8d5604650c763e2c5887a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d33a23b053 ]
The bitreverse helper is almost always built into the kernel,
but in a rare randconfig build it is possible to hit a case
in which it is a loadable module while the atmel-i2c driver
is built-in:
arm-linux-gnueabi-ld: drivers/crypto/atmel-i2c.o: in function `atmel_i2c_checksum':
atmel-i2c.c:(.text+0xa0): undefined reference to `byte_rev_table'
Add one more 'select' statement to prevent this.
Fixes: 11105693fa ("crypto: atmel-ecc - introduce Microchip / Atmel ECC driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1efdb604f ]
The platform device driver name is "max77693-muic", so advertise it
properly in the modalias string. This fixes automated module loading when
this driver is compiled as a module.
Fixes: db1b903742 ("extcon: MAX77693: Add extcon-max77693 driver to support Maxim MAX77693 MUIC device")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 88149082bb ]
If generic_drop_inode() returns true, it means iput_final() can evict
this inode regardless of whether it is dirty or not. If we check
I_DONTCACHE in generic_drop_inode(), any inode with this bit set will be
evicted unconditionally. This is not the desired behavior because
I_DONTCACHE only means the inode shouldn't be cached on the LRU list.
As for whether we need to evict this inode, this is what
generic_drop_inode() should do. This patch corrects the usage of
I_DONTCACHE.
This patch was proposed in [1].
[1]: https://lore.kernel.org/linux-fsdevel/20200831003407.GE12096@dread.disaster.area/
Fixes: dae2f8ed79 ("fs: Lift XFS_IDONTCACHE to the VFS layer")
Signed-off-by: Hao Li <lihao2018.fnst@cn.fujitsu.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 092fde0f86 ]
Fix a possible hang in xdpsock that can occur when using multiple
threads. In this case, one or more of the threads might get stuck in
the while-loop in tx_only after the user has signaled the main thread
to stop execution. In this case, no more Tx packets will be sent, so a
thread might get stuck in the aforementioned while-loop. Fix this by
introducing a test inside the while-loop to check if the benchmark has
been terminated. If so, return from the function.
Fixes: cd9e72b6f2 ("samples/bpf: xdpsock: Add option to specify batch size")
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20201210163407.22066-1-magnus.karlsson@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b391c7f2e ]
pm_runtime_get_sync() will increment pm usage at first and it
will resume the device later. If runtime of the device has
error or device is in inaccessible state(or other error state),
resume operation will fail. If we do not call put operation to
decrease the reference, it will result in reference leak in
the two functions(gpmi_init and gpmi_nfc_exec_op). Moreover,
this device cannot enter the idle state and always stay busy or
other non-idle state later. So we fixed it through adding
pm_runtime_put_noidle.
Fixes: 5bc6bb603b ("mtd: rawnand: gpmi: Fix suspend/resume problem")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201107110552.1568742-1-zhangqilong3@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5bf5861d6e ]
The periph_clks[] array contains duplicated entry for Security Engine
clock which was meant to be defined for T210, but it wasn't added
properly. This patch corrects the T210 SE entry and fixes the following
error message on T114/T124: "Tegra clk 127: register failed with -17".
Fixes: dc37fec483 ("clk: tegra: periph: Add new periph clks and muxes for Tegra210")
Tested-by Nicolas Chauvet <kwizart@gmail.com>
Reported-by Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20201025224212.7790-1-digetx@gmail.com
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d37a8d192 ]
I would repeat the same commit message that was in commit 5e4b7e82d4
("clk: qcom: gcc-sdm845: Use floor ops for sdcc clks") but it seems
silly to do so when you could just go read that commit.
NOTE: this is actually extra terrible because we're missing the 50 MHz
rate in the table (see the next patch AKA ("clk: qcom: gcc-sc7180: Add
50 MHz clock rate for SDC2")). That means then when you run an older
SD card it'll try to clock it at 100 MHz when it's only specced to run
at 50 MHz max. As you can probably guess that doesn't work super
well.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Fixes: 17269568f7 ("clk: qcom: Add Global Clock controller (GCC) driver for SC7180")
Link: https://lore.kernel.org/r/20201210102234.1.I096779f219625148900fc984dd0084ed1ba87c7f@changeid
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3d4e5b126 ]
platform_get_resource() may fail and in this case a NULL dereference
will occur.
Fix it to use devm_platform_ioremap_resource() instead of calling
platform_get_resource() and devm_ioremap().
This is detected by Coccinelle semantic patch.
@@
expression pdev, res, n, t, e, e1, e2;
@@
res = \(platform_get_resource\|platform_get_resource_byname\)(pdev, t,
n);
+ if (!res)
+ return -EINVAL;
... when != res == NULL
e = devm_ioremap(e1, res->start, e2);
Fixes: dc160e4491 ("remoteproc: qcom: Introduce Non-PAS ADSP PIL driver")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1607392460-20516-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c0a6e5ee1e ]
If the pm_runtime_get_sync failed in adsp_pds_enable when
loop (i), The unroll_pd_votes will start from (i - 1), and
it will resulted in following problems:
1) pm_runtime_get_sync will increment pm usage counter even it
failed. Forgetting to pm_runtime_put_noidle will result in
reference leak.
2) Have not reset pds[i] performance state.
Then we fix it.
Fixes: 17ee2fb4e8 ("remoteproc: qcom: pas: Vote for active/proxy power domains")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201102143554.144707-1-zhangqilong3@huawei.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a247230500 ]
If the pm_runtime_get_sync failed in q6v5_pds_enable when
loop (i), The unroll_pd_votes will start from (i - 1), and
it will resulted in following problems:
1) pm_runtime_get_sync will increment pm usage counter even it
failed. Forgetting to pm_runtime_put_noidle will result in
reference leak.
2) Have not reset pds[i] performance state.
Then we fix it.
Fixes: 4760a896be ("remoteproc: q6v5-mss: Vote for rpmh power domains")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201102143433.143996-1-zhangqilong3@huawei.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e0da68994d ]
Fix incorrect type of max_entries in UVERBS_METHOD_QUERY_GID_TABLE -
max_entries is of type size_t although it can take negative values.
The following static check revealed it:
drivers/infiniband/core/uverbs_std_types_device.c:338 ib_uverbs_handler_UVERBS_METHOD_QUERY_GID_TABLE() warn: 'max_entries' unsigned <= 0
Fixes: 9f85cbe50a ("RDMA/uverbs: Expose the new GID query API to user space")
Link: https://lore.kernel.org/r/20201208073545.9723-4-leon@kernel.org
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 779e0bf476 ]
In procedure ib_register_device, procedure kobject_uevent is called
(advertising that the device is ready for userspace usage) even when
device_enable_and_get() returned an error.
As a result, various RDMA modules attempted to register for the device
even while the device driver was preparing to unregister the device.
Fix this by advertising the device availability only after enabling the
device succeeds.
Fixes: e7a5b4aafd ("RDMA/device: Don't fire uevent before device is fully initialized")
Link: https://lore.kernel.org/r/20201208073545.9723-3-leon@kernel.org
Suggested-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1a5039759 ]
A problem exists in enabling silent stream when connection type is
DisplayPort. Silent stream programming is completed when a new DP
receiver is connected, but infoframe transmission does not actually
start until PCM is opened for the first time. This can result in audible
gap of multiple seconds. This only affects the first PCM open.
Fix the issue by properly assigning a converter to the silent stream,
and modifying the required stream ID programming sequence.
This change only affects Intel display audio codecs.
BugLink: https://github.com/thesofproject/linux/issues/2468
Fixes: 951894cf30 ("ALSA: hda/hdmi: Add Intel silent stream support")
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20201210174445.3134104-1-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 428bb00114 ]
platform_get_resource_byname() may fail and in this case a NULL
dereference will occur.
Fix it to use devm_platform_ioremap_resource_byname() instead of calling
platform_get_resource_byname() and devm_ioremap().
This is detected by Coccinelle semantic patch.
@@
expression pdev, res, n, t, e, e1, e2;
@@
res = \(platform_get_resource\|platform_get_resource_byname\)(pdev, t,
n);
+ if (!res)
+ return -EINVAL;
... when != res == NULL
e = devm_ioremap(e1, res->start, e2);
Fixes: ad7fcbc308 ("slimbus: qcom: Add Qualcomm Slimbus controller driver")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1607392473-20610-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 14653942de ]
The R-Car V3U clock driver defines the R and OSC clocks using R-Car Gen3
clock types. However, The R-Car V3U clock driver does not use the R-Car
Gen3 clock driver core, hence registering the R and OSC clocks fails:
renesas-cpg-mssr e6150000.clock-controller: Failed to register core clock osc: -22
renesas-cpg-mssr e6150000.clock-controller: Failed to register core clock r: -22
Fix this by introducing clock definition macros specific to R-Car V3U.
Note that rcar_r8a779a0_cpg_clk_register() already handled the related
clock types. Drop the now unneeded include of rcar-gen3-cpg.h.
Fixes: 17bcc8035d ("clk: renesas: cpg-mssr: Add support for R-Car V3U")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201109152614.2465483-1-geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 74639cbf51 ]
There isn't any need to overwrite the mode here in the driver with what
has been detected by the firmware, such as DT or ACPI. In fact, if we
use the SPI CS gpio descriptor feature we will overwrite the mode with
SPI_MODE_0 where it already contains SPI_MODE_0 and more importantly
SPI_CS_HIGH. Clearing the SPI_CS_HIGH bit causes the CS line to toggle
when the device is probed when it shouldn't change, confusing the driver
and making it fail to probe. Drop the assignment and let the spi core
take care of it.
Fixes: a17d94f0b6 ("mfd: Add ChromeOS EC SPI driver")
Cc: Simon Glass <sjg@chromium.org>
Cc: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Cc: Alexandru M Stan <amstan@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20201204193540.3047030-2-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78ff2733ff ]
Fix to restore BTF if single-stepping causes a page fault and
it is cancelled.
Usually the BTF flag was restored when the single stepping is done
(in resume_execution()). However, if a page fault happens on the
single stepping instruction, the fault handler is invoked and
the single stepping is cancelled. Thus, the BTF flag is not
restored.
Fixes: 1ecc798c67 ("x86: debugctlmsr kprobes")
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/160389546985.106936.12727996109376240993.stgit@devnote2
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca9364dde5 ]
Since commit b4868b44c5 ("NFSv4: Wait for stateid updates after
CLOSE/OPEN_DOWNGRADE"), every inter server copy operation suffers 5
seconds delay regardless of the size of the copy. The delay is from
nfs_set_open_stateid_locked when the check by nfs_stateid_is_sequential
fails because the seqid in both nfs4_state and nfs4_stateid are 0.
Fix by modifying nfs4_init_cp_state to return the stateid with seqid 1
instead of 0. This is also to conform with section 4.8 of RFC 7862.
Here is the relevant paragraph from section 4.8 of RFC 7862:
A copy offload stateid's seqid MUST NOT be zero. In the context of a
copy offload operation, it is inappropriate to indicate "the most
recent copy offload operation" using a stateid with a seqid of zero
(see Section 8.2.2 of [RFC5661]). It is inappropriate because the
stateid refers to internal state in the server and there may be
several asynchronous COPY operations being performed in parallel on
the same file by the server. Therefore, a copy offload stateid with
a seqid of zero MUST be considered invalid.
Fixes: ce0887ac96 ("NFSD add nfs4 inter ssc to nfsd4_copy")
Signed-off-by: Dai Ngo <dai.ngo@oracle.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4420440c57 ]
The warning message from nfsd terminating normally
can confuse system adminstrators or monitoring software.
Though it's not exactly fair to pin-point a commit where it
originated, the current form in the current place started
to appear in:
Fixes: e096bbc648 ("knfsd: remove special handling for SIGHUP")
Signed-off-by: kazuo ito <kzpn200@gmail.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 45fe7befe0 ]
Functions that are annotated __exit are discarded for built-in drivers,
but the .remove callback in a device driver must still be kept around
to allow bind/unbind operations.
There is now a linker warning for the discarded symbol references:
`tmc_remove' referenced in section `.data' of drivers/hwtracing/coresight/coresight-tmc-core.o: defined in discarded section `.exit.text' of drivers/hwtracing/coresight/coresight-tmc-core.o
`tpiu_remove' referenced in section `.data' of drivers/hwtracing/coresight/coresight-tpiu.o: defined in discarded section `.exit.text' of drivers/hwtracing/coresight/coresight-tpiu.o
`etb_remove' referenced in section `.data' of drivers/hwtracing/coresight/coresight-etb10.o: defined in discarded section `.exit.text' of drivers/hwtracing/coresight/coresight-etb10.o
`static_funnel_remove' referenced in section `.data' of drivers/hwtracing/coresight/coresight-funnel.o: defined in discarded section `.exit.text' of drivers/hwtracing/coresight/coresight-funnel.o
`dynamic_funnel_remove' referenced in section `.data' of drivers/hwtracing/coresight/coresight-funnel.o: defined in discarded section `.exit.text' of drivers/hwtracing/coresight/coresight-funnel.o
`static_replicator_remove' referenced in section `.data' of drivers/hwtracing/coresight/coresight-replicator.o: defined in discarded section `.exit.text' of drivers/hwtracing/coresight/coresight-replicator.o
`dynamic_replicator_remove' referenced in section `.data' of drivers/hwtracing/coresight/coresight-replicator.o: defined in discarded section `.exit.text' of drivers/hwtracing/coresight/coresight-replicator.o
`catu_remove' referenced in section `.data' of drivers/hwtracing/coresight/coresight-catu.o: defined in discarded section `.exit.text' of drivers/hwtracing/coresight/coresight-catu.o
Remove all those annotations.
Fixes: 8b0cf82677 ("coresight: stm: Allow to build coresight-stm as a module")
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20201208182651.1597945-3-mathieu.poirier@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b097efba95 ]
Currently there is a null pointer check for hdmi_phy that implies it
may be null, however a dev_err messages dereferences this potential null
pointer. Avoid a null pointer dereference by only emitting the dev_err
message if hdmi_phy is non-null. It is a moot point if the error message
needs to be printed at all, but since this is a relatively new piece of
code it may be useful to keep the message in for the moment in case there
are unforseen errors that need to be reported.
Fixes: be28b6507c ("drm/mediatek: separate hdmi phy to different file")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Addresses-Coverity: ("Dereference after null check")
Link: https://lore.kernel.org/r/20201207150937.170435-1-colin.king@canonical.com
[vkoul: fix indent of return call]
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b866459489 ]
Partitions with cache nodes in the device tree can encounter the
following warning on resume:
CPU 0 already accounted in PowerPC,POWER9@0(Data)
WARNING: CPU: 0 PID: 3177 at arch/powerpc/kernel/cacheinfo.c:197 cacheinfo_cpu_online+0x640/0x820
These calls to cacheinfo_cpu_offline/online have been redundant since
commit e610a466d1 ("powerpc/pseries/mobility: rebuild cacheinfo
hierarchy post-migration").
Fixes: e610a466d1 ("powerpc/pseries/mobility: rebuild cacheinfo hierarchy post-migration")
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201207215200.1785968-25-nathanl@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 52719fce3f ]
There are three ways pseries_suspend_begin() can be reached:
1. When "mem" is written to /sys/power/state:
kobj_attr_store()
-> state_store()
-> pm_suspend()
-> suspend_devices_and_enter()
-> pseries_suspend_begin()
This never works because there is no way to supply a valid stream id
using this interface, and H_VASI_STATE is called with a stream id of
zero. So this call path is useless at best.
2. When a stream id is written to /sys/devices/system/power/hibernate.
pseries_suspend_begin() is polled directly from store_hibernate()
until the stream is in the "Suspending" state (i.e. the platform is
ready for the OS to suspend execution):
dev_attr_store()
-> store_hibernate()
-> pseries_suspend_begin()
3. When a stream id is written to /sys/devices/system/power/hibernate
(continued). After #2, pseries_suspend_begin() is called once again
from the pm core:
dev_attr_store()
-> store_hibernate()
-> pm_suspend()
-> suspend_devices_and_enter()
-> pseries_suspend_begin()
This is redundant because the VASI suspend state is already known to
be Suspending.
The begin() callback of platform_suspend_ops is optional, so we can
simply remove that assignment with no loss of function.
Fixes: 32d8ad4e62 ("powerpc/pseries: Partition hibernation support")
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201207215200.1785968-18-nathanl@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f77ac2e378 ]
There are a couple of problems with the exception entry code that deals
with FP exceptions (which are reported as UND exceptions) when building
the kernel in Thumb2 mode:
- the conditional branch to vfp_kmode_exception in vfp_support_entry()
may be out of range for its target, depending on how the linker decides
to arrange the sections;
- when the UND exception is taken in kernel mode, the emulation handling
logic is entered via the 'call_fpe' label, which means we end up using
the wrong value/mask pairs to match and detect the NEON opcodes.
Since UND exceptions in kernel mode are unlikely to occur on a hot path
(as opposed to the user mode version which is invoked for VFP support
code and lazy restore), we can use the existing undef hook machinery for
any kernel mode instruction emulation that is needed, including calling
the existing vfp_kmode_exception() routine for unexpected cases. So drop
the call to call_fpe, and instead, install an undef hook that will get
called for NEON and VFP instructions that trigger an UND exception in
kernel mode.
While at it, make sure that the PC correction is accurate for the
execution mode where the exception was taken, by checking the PSR
Thumb bit.
Cc: Dmitry Osipenko <digetx@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Fixes: eff8728fe6 ("vmlinux.lds.h: Add PGO and AutoFDO input sections")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf791774a1 ]
Fix array names to match assignments for data items and data items
counter in 'mlxplat_mlxcpld_comex_items' structure for:
.data = mlxplat_mlxcpld_default_pwr_items_data,
.count = ARRAY_SIZE(mlxplat_mlxcpld_pwr),
and
.data = mlxplat_mlxcpld_default_fan_items_data,
.count = ARRAY_SIZE(mlxplat_mlxcpld_fan),
Replace:
- 'mlxplat_mlxcpld_pwr' by 'mlxplat_mlxcpld_default_pwr_items_data' for
ARRAY_SIZE() calculation.
- 'mlxplat_mlxcpld_fan' by 'mlxplat_mlxcpld_default_fan_items_data'
for ARRAY_SIZE() calculation.
Fixes: bdd6e155e0 ("platform/x86: mlx-platform: Add support for new system type")
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20201207174745.22889-3-vadimp@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ba4939f1dd ]
Fix array names to match assignments for data items and data items
counter in 'mlxplat_mlxcpld_default_items' structure for:
.data = mlxplat_mlxcpld_default_pwr_items_data,
.count = ARRAY_SIZE(mlxplat_mlxcpld_pwr),
and
.data = mlxplat_mlxcpld_default_fan_items_data,
.count = ARRAY_SIZE(mlxplat_mlxcpld_fan),
Replace:
- 'mlxplat_mlxcpld_pwr' by 'mlxplat_mlxcpld_default_pwr_items_data' for
ARRAY_SIZE() calculation.
- 'mlxplat_mlxcpld_fan' by 'mlxplat_mlxcpld_default_fan_items_data'
for ARRAY_SIZE() calculation.
Fixes: c6acad68eb ("platform/mellanox: mlxreg-hotplug: Modify to use a regmap interface")
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20201207174745.22889-2-vadimp@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d9a9280a0d ]
Building with W=2 prints a number of warnings for one function that
has a pointer type mismatch:
linux/seq_buf.h: In function 'seq_buf_init':
linux/seq_buf.h:35:12: warning: pointer targets in assignment from 'unsigned char *' to 'char *' differ in signedness [-Wpointer-sign]
Change the type in the function prototype according to the type in
the structure.
Link: https://lkml.kernel.org/r/20201026161108.3707783-1-arnd@kernel.org
Fixes: 9a7777935c ("tracing: Convert seq_buf fields to be like seq_file fields")
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c183c406c4 ]
According to the datasheet (Rev. 1.9) the RTL8211F requires at least
72ms "for internal circuits settling time" before accessing the PHY
registers. This fixes an issue seen on ODROID-C2 where the Ethernet
link doesn't come up when using ip link set down/up:
[ 6630.714855] meson8b-dwmac c9410000.ethernet eth0: Link is Down
[ 6630.785775] meson8b-dwmac c9410000.ethernet eth0: PHY [stmmac-0:00] driver [RTL8211F Gigabit Ethernet] (irq=36)
[ 6630.893071] meson8b-dwmac c9410000.ethernet: Failed to reset the dma
[ 6630.893800] meson8b-dwmac c9410000.ethernet eth0: stmmac_hw_setup: DMA engine initialization failed
[ 6630.902835] meson8b-dwmac c9410000.ethernet eth0: stmmac_open: Hw setup failed
Fixes: f29cabf240 ("arm64: dts: meson: use the generic Ethernet PHY reset GPIO bindings")
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/4a322c198b86e4c8b3dda015560a683babea4d63.1607363522.git.stefan@agner.ch
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c7412530d ]
According to the datasheet (Rev. 1.9) the RTL8211F requires at least
72ms "for internal circuits settling time" before accessing the PHY
registers. This fixes an issue where the Ethernet link doesn't come up
when using ip link set down/up:
[ 29.360965] meson8b-dwmac ff3f0000.ethernet eth0: Link is Down
[ 34.569012] meson8b-dwmac ff3f0000.ethernet eth0: PHY [0.0:00] driver [RTL8211F Gigabit Ethernet] (irq=31)
[ 34.676732] meson8b-dwmac ff3f0000.ethernet: Failed to reset the dma
[ 34.678874] meson8b-dwmac ff3f0000.ethernet eth0: stmmac_hw_setup: DMA engine initialization failed
[ 34.687850] meson8b-dwmac ff3f0000.ethernet eth0: stmmac_open: Hw setup failed
Fixes: 658e4129bb ("arm64: dts: meson: g12b: odroid-n2: add the Ethernet PHY reset line")
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/df3f5c4fc6e43c55429fd3662a636036a21eed49.1607363522.git.stefan@agner.ch
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e6204d4620 ]
This is considered bad for the following reasons:
(1) We only support the block protection with BPn bits for write
protection. Not all Atmel parts support this.
(2) Newly added flash chip will automatically inherit the "has
locking" support and thus needs to explicitly tested. Better
be opt-in instead of opt-out.
(3) There are already supported flashes which doesn't support
the locking scheme. So I assume this wasn't properly tested
before adding that chip; which enforces my previous argument
that locking support should be an opt-in.
Remove the global flag and add individual flags to all flashes which
supports BP locking. In particular the following flashes don't support
the BP scheme:
- AT26F004
- AT25SL321
- AT45DB081D
Please note, that some flashes which are marked as SPI_NOR_HAS_LOCK just
support Global Protection, i.e. not our supported block protection
locking scheme. This is to keep backwards compatibility with the
current "unlock all at boot" mechanism. In particular the following
flashes doesn't have BP bits:
- AT25DF041A
- AT25DF321
- AT25DF321A
- AT25DF641
- AT26DF081A
- AT26DF161A
- AT26DF321
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201203162959.29589-4-michael@walle.cc
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bdb1a75e4b ]
Just try to unlock the whole SPI-NOR flash array. Don't abort the
probing in case of an error. Justifications:
(1) For some boards, this just works because
spi_nor_write_16bit_sr_and_check() is broken and just checks the
second half of the 16bit. Once that will be fixed, SPI probe will
fail for boards which has hardware-write protected SPI-NOR flashes.
(2) Until now, hardware write-protection was the only viable solution
to use the block protection bits. This is because this very
function spi_nor_unlock_all() will be called unconditionally on
every linux boot. Therefore, this bits only makes sense in
combination with the hardware write-protection. If we would fail
the SPI probe on an error in spi_nor_unlock_all() we'd break
virtually all users of the block protection bits.
(3) We should try hard to keep the MTD working even if the flash might
not be writable/erasable.
Fixes: 3e0930f109 ("mtd: spi-nor: Rework the disabling of block write protection")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201203162959.29589-3-michael@walle.cc
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a4327979a1 ]
Some HP x360 models have an ACPI VGBS method which sets bit 4 instead of
bit 6 when NOT in tablet mode at boot. Inspecting all the DSDTs in my DSDT
collection shows only one other model, the Medion E1239T ever setting bit 4
and it always sets this together with bit 6.
So lets treat bit 4 as a second bit which when set indicates the device not
being in tablet-mode, as we already do for bit 6.
While at it also prefix all VGBS constant defines with "VGBS_".
Note this wrokaround was first added to the kernel as
commit d823346876 ("platform/x86: intel-vbtn: Fix SW_TABLET_MODE always
reporting 1 on the HP Pavilion 11 x360").
After commit 8169bd3e6e ("platform/x86: intel-vbtn: Switch to an
allow-list for SW_TABLET_MODE reporting") got added to the kernel this
was reverted, because with the new allow-list approach the workaround
was no longer necessary for the model on which the issue was first
reported.
But it turns out that the workaround is still necessary because some
affected models report a chassis-type of 31 which is on the allow-list.
BugLink: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1894017
Fixes: 21d64817c7 ("platform/x86: intel-vbtn: Revert "Fix SW_TABLET_MODE always reporting 1 on the HP Pavilion 11 x360"")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d74e0ae7e0 ]
Commit cde1a8a992 ("Bluetooth: btusb: Fix and detect most of the
Chinese Bluetooth controllers") made the detection of fake controllers
more generic fixing it for much of the newer fakes / clones.
But this does not work for a fake CSR controller with a bcdDevice
value of 0x0134, which was correctly identified as fake before
this change.
Add an extra check for this special case, checking for a combination
of a bcdDevice value of 0x0134, together with a lmp_subver of 0x0c5c
and a hci_ver of BLUETOOTH_VER_2_0.
The chip inside this fake dongle is marked as with "clockwise cw6629d".
Fixes: cde1a8a992 ("Bluetooth: btusb: Fix and detect most of the Chinese Bluetooth controllers")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 733c15bd3a ]
Currently in the case where dev->blk_symlink_name fails to be allocates
the error return path attempts to set an end-of-string character to
the unallocated dev->blk_symlink_name causing a null pointer dereference
error. Fix this by returning with an explicity ENOMEM error (which also
is missing in the original code as was not initialized).
Fixes: 1eb54f8f5d ("block/rnbd: client: sysfs interface functions")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Addresses-Coverity: ("Dereference after null check")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 64e8a6ece1 ]
For every rnbd_clt_dev, we alloc the pathname and blk_symlink_name
statically to NAME_MAX which is 255 bytes. In most of the cases we only
need less than 10 bytes, so 500 bytes per block device are wasted.
This commit dynamically allocates memory buffer for pathname and
blk_symlink_name.
Signed-off-by: Md Haris Iqbal <haris.iqbal@cloud.ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Reviewed-by: Lutz Pogrell <lutz.pogrell@cloud.ionos.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c9cfbadfa ]
A recent patch incorrectly altered the adb-iop state machine behaviour
and introduced a regression that can appear intermittently as a
malfunctioning ADB input device. This seems to be caused when reply
packets from different ADB commands become mixed up, especially during
the adb bus scan. Fix this by unconditionally entering the awaiting_reply
state after sending an explicit command, even when the ADB command won't
generate a reply from the ADB device.
It turns out that the IOP always generates reply messages, even when the
ADB command does not produce a reply packet (e.g. ADB Listen command).
So it's not really the ADB reply packets that are being mixed up, it's the
IOP messages that enclose them. The bug goes like this:
1. CPU sends a message to the IOP, expecting no response because this
message contains an ADB Listen command. The ADB command is now
considered complete.
2. CPU sends a second message to the IOP, this time expecting a
response because this message contains an ADB Talk command. This
ADB command needs a reply before it can be completed.
3. adb-iop driver receives an IOP message and assumes that it relates
to the Talk command. It's actually an empty one (with flags ==
ADB_IOP_EXPLICIT|ADB_IOP_TIMEOUT) for the previous command. The
Talk command is now considered complete but it gets the wrong reply
data.
4. adb-iop driver gets another IOP response message, which contains
the actual reply data for the Talk command, but this is dropped
(the driver is no longer in awaiting_reply state).
Cc: Joshua Thompson <funaho@jurai.org>
Fixes: e2954e5f72 ("macintosh/adb-iop: Implement sending -> idle state transition")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Link: https://lore.kernel.org/r/0f0a25855391e7eaa53a50f651aea0124e8525dd.1605847196.git.fthain@telegraphics.com.au
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc928b901d ]
A driver should not 'select' drivers from another subsystem.
If NVMEM is disabled, this one results in a warning:
WARNING: unmet direct dependencies detected for NVMEM_IMX_OCOTP
Depends on [n]: NVMEM [=n] && (ARCH_MXC [=y] || COMPILE_TEST [=y]) && HAS_IOMEM [=y]
Selected by [y]:
- ARM_IMX6Q_CPUFREQ [=y] && CPU_FREQ [=y] && (ARM || ARM64 [=y]) && ARCH_MXC [=y] && REGULATOR_ANATOP [=y]
Change the 'select' to 'depends on' to prevent it from going wrong,
and allow compile-testing without that driver, since it is only
a runtime dependency.
Fixes: 2782ef34ed ("cpufreq: imx: Select NVMEM_IMX_OCOTP")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c0382d049d ]
This patch adds missing MODULE_ALIAS for automatic loading of this cpufreq
driver when it is compiled as an external module.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 8def31034d ("cpufreq: arm_big_little: add SCPI interface driver")
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b9acab0918 ]
This patch adds missing MODULE_ALIAS for automatic loading of this cpufreq
driver when it is compiled as an external module.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: a0a22cf144 ("cpufreq: Loongson1: Add cpufreq driver for Loongson1B")
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit af2096f285 ]
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this cpufreq driver when it is
compiled as an external module.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: f328584f7b ("cpufreq: Add sun50i nvmem based CPU scaling driver")
Reviewed-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 183747ab52 ]
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this cpufreq driver when it is
compiled as an external module.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: ab0ea257fc ("cpufreq: st: Provide runtime initialised driver for ST's platforms")
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5a6031663 ]
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this cpufreq driver when it is
compiled as an external module.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 46e2856b8e ("cpufreq: Add Kryo CPU scaling driver")
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit af6eca0650 ]
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this cpufreq driver when it is
compiled as an external module.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 501c574f4e ("cpufreq: mediatek: Add support of cpufreq to MT2701/MT7623 SoC")
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9433777a6e ]
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this cpufreq driver when it is
compiled as an external module.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 6754f55610 ("cpufreq / highbank: add support for highbank cpufreq")
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 925a5bcefe ]
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this cpufreq driver when it is
compiled as an external module.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: f525a67053 ("cpufreq: ap806: add cpufreq driver for Armada 8K")
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b7770b877 ]
ARM virtual counter supports event stream, it can only trigger an event
when the trigger bit (the value of CNTKCTL_EL1.EVNTI) of CNTVCT_EL0 changes,
so the actual period of event stream is 2^(cntkctl_evnti + 1). For example,
when the trigger bit is 0, then virtual counter trigger an event for every
two cycles.
While we're at it, rework the way we compute the trigger bit position
by making it more obvious that when bits [n:n-1] are both set (with n
being the most significant bit), we pick bit (n + 1).
Fixes: 037f637767 ("drivers: clocksource: add support for ARM architected timer event stream")
Suggested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Keqian Zhu <zhukeqian1@huawei.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201204073126.6920-3-zhukeqian1@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d8cc3905b8 ]
In commit 0ea415390c ("clocksource/arm_arch_timer: Use arch_timer_read_counter
to access stable counters"), we separate stable and normal count reader to omit
unnecessary overhead on systems that have no timer erratum.
However, in erratum_set_next_event_tval_generic(), count reader becomes normal
reader. This converts it to stable reader.
Fixes: 0ea415390c ("clocksource/arm_arch_timer: Use arch_timer_read_counter to access stable counters")
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Keqian Zhu <zhukeqian1@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201204073126.6920-2-zhukeqian1@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e319a1b956 ]
The iommu pgtable support is only available when IOMMU support
is built into the kernel:
WARNING: unmet direct dependencies detected for IOMMU_IO_PGTABLE
Depends on [n]: IOMMU_SUPPORT [=n]
Selected by [y]:
- DRM_MSM [=y] && HAS_IOMEM [=y] && DRM [=y] && (ARCH_QCOM [=y] || SOC_IMX5 || ARM && COMPILE_TEST [=y]) && OF [=y] && COMMON_CLK [=y] && MMU [=y] && (QCOM_OCMEM [=y] || QCOM_OCMEM [=y]=n)
Fix the dependency accordingly. There is no need for depending on
CONFIG_MMU any more, as that is implied by the iommu support.
Fixes: b145c6e65e ("drm/msm: Add support to create a local pagetable")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7cc29fcdfc ]
nr_rings is reset to 1, but when this function is called for a second
(and third!) time nr_rings > 1 is false, thus the else case is entered
to set up a buffer for the RPTR shadow and consequently written to
RB_RPTR_ADDR, hanging platforms without WHERE_AM_I firmware support.
Restructure the condition in such a way that shadow buffer setup only
ever happens when has_whereami is true; otherwise preemption is only
finalized when the number of ring buffers has not been reset to 1 yet.
Fixes: 8907afb476 ("drm/msm: Allow a5xx to mark the RPTR shadow as privileged")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d77d22d701 ]
The driver can be compile-tested on all ARM machines, but
causes a failure when built for ARMv7-M:
arm-linux-gnueabi-ld: error: drivers/memory/ti-emif-sram-pm.o: conflicting architecture profiles A/M
Limit the target machines to configurations that have ARMv7 enabled.
Fixes: ea0c0ad6b6 ("memory: Enable compile testing for most of the drivers")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20201203230832.1481767-1-arnd@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f5f6e01f91 ]
Compile-testing the DRM_MEDIATEK_HDMI driver shows two missing
dependencies, one results in a link failure:
arm-linux-gnueabi-ld: drivers/phy/mediatek/phy-mtk-hdmi.o: in function `mtk_hdmi_phy_probe':
phy-mtk-hdmi.c:(.text+0xd8): undefined reference to `__clk_get_name'
arm-linux-gnueabi-ld: phy-mtk-hdmi.c:(.text+0x12c): undefined reference to `devm_clk_register'
arm-linux-gnueabi-ld: phy-mtk-hdmi.c:(.text+0x250): undefined reference to `of_clk_add_provider'
arm-linux-gnueabi-ld: phy-mtk-hdmi.c:(.text+0x298): undefined reference to `of_clk_src_simple_get'
The other one is a harmless warning:
WARNING: unmet direct dependencies detected for PHY_MTK_HDMI
Depends on [n]: ARCH_MEDIATEK [=n] && OF [=y]
Selected by [y]:
- DRM_MEDIATEK_HDMI [=y] && HAS_IOMEM [=y] && DRM_MEDIATEK [=y]
Fix these by adding dependencies on CONFIG_OF and CONFIG_COMMON_CLK.
With that done, there is also no reason against adding
CONFIG_COMPILE_TEST.
Fixes: b28be59a2e ("phy: mediatek: Move mtk_hdmi_phy driver into drivers/phy/mediatek folder")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20201204135650.2744481-1-arnd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7061b8a522 ]
gcc points out a memory area that is copied to a device
but not initialized:
sound/soc/codecs/cros_ec_codec.c: In function 'i2s_rx_event':
arch/x86/include/asm/string_32.h:83:20: error: '*((void *)&p+4)' may be used uninitialized in this function [-Werror=maybe-uninitialized]
83 | *((int *)to + 1) = *((int *)from + 1);
Initialize all the unused fields to zero.
Fixes: 727f1c71c7 ("ASoC: cros_ec_codec: refactor I2S RX")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20201203225458.1477830-1-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4d7659bfbe ]
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 2ca4c92f58 ("dm ioctl: prevent empty message")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc348defcc ]
Run mt76_free_device instead of ieee80211_free_hw if device probing
fails in order to remove the already allocated mt76 workqueue
Fixes: a86f1d01f5 ("mt76: move mt76 workqueue in common code")
Fixes: f1d962369d ("mt76: mt7915: implement HE per-rate tx power support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 907af0f0ca ]
mlx5 firmware expects driver version in specific format X.X.X, so
make it always correct and based on real kernel version aligned with
the driver.
Fixes: 012e50e109 ("net/mlx5: Set driver version into firmware")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9df085ce1 ]
If THIS_MODULE is not set, the module would be removed while debugfs is
being used.
It eventually makes kernel panic.
Fixes: e57b790146 ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5efbe3b1b8 ]
If THIS_MODULE is not set, the module would be removed while debugfs is
being used.
It eventually makes kernel panic.
Fixes: ec9742a8f3 ("mt76: mt7915: add .sta_add_debugfs support")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d121f125af ]
Linux doesn't own the memory immediately after the kernel image. On Octeon
bootloader places a shared structure right close after the kernel _end,
refer to "struct cvmx_bootinfo *octeon_bootinfo" in cavium-octeon/setup.c.
If check_kernel_sections_mem() rounds the PFNs up, first memblock_alloc()
inside early_init_dt_alloc_memory_arch() <= device_tree_init() returns
memory block overlapping with the above octeon_bootinfo structure, which
is being overwritten afterwards.
Fixes: a94e4f24ec ("MIPS: init: Drop boot_mem_map")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 94dad6bed3 ]
For UARTs, the local pull-ups should be on the RX pin, not the TX pin.
UARTs transmit active-low, so a disconnected RX pin should be pulled
high instead of left floating to prevent noise being interpreted as
transmissions.
This gets rid of bogus sysrq events when the UART console is not
connected.
Fixes: 52e02d377a ("arm64: dts: rockchip: add core dtsi file for RK3328 SoCs")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20201204064805.6480-1-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eceae70bde ]
strncat()'s third argument is how many bytes will be added *in addition* to
already existing bytes in destination. Plus extra zero byte will be added
after that. So existing use in test_sockmap has many opportunities to overflow
the string and cause memory corruptions. And in this case, GCC complains for
a good reason.
Fixes: 16962b2404 ("bpf: sockmap, add selftests")
Fixes: 73563aa3d9 ("selftests/bpf: test_sockmap, print additional test options")
Fixes: 1ade9abadf ("bpf: test_sockmap, add options for msg_pop_data() helper")
Fixes: 463bac5f1c ("bpf, selftests: Add test for ktls with skb bpf ingress policy")
Fixes: e9dd904708 ("bpf: add tls support for testing in test_sockmap")
Fixes: 753fb2ee09 ("bpf: sockmap, add msg_peek tests to test_sockmap")
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20201203235440.2302137-2-andrii@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7d2c6b1edf ]
Changeset 6b80975c63 ("scripts: kernel-doc: fix typedef parsing")
added support for things like:
typedef unsigned long foo();
However, it caused a regression on this prototype:
typedef bool v4l2_check_dv_timings_fnc(const struct v4l2_dv_timings *t, void *handle);
This is only noticed after adding a patch that checks if the
kernel-doc identifier matches the typedef:
./scripts/kernel-doc -none $(git grep '^.. kernel-doc::' Documentation/ |cut -d ' ' -f 3|sort|uniq) 2>&1|grep expecting
include/media/v4l2-dv-timings.h:38: warning: expecting prototype for typedef v4l2_check_dv_timings_fnc. Prototype was for typedef nc instead
The problem is that, with the new parsing logic, it is not
checking for complete words at the type part.
Fix it by adding a \b at the end of each type word at the
regex.
fixes: 6b80975c63 ("scripts: kernel-doc: fix typedef parsing")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/218ff56dcb8e73755005d3fb64586eb1841a276b.1606896997.git.mchehab+huawei@kernel.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9cf309c56f ]
When we added sanitising of map names before loading programs to libbpf, we
still allowed periods in the name. While the kernel will accept these for
the map names themselves, they are not allowed in file names when pinning
maps. This means that bpf_object__pin_maps() will fail if called on an
object that contains internal maps (such as sections .rodata).
Fix this by replacing periods with underscores when constructing map pin
paths. This only affects the paths generated by libbpf when
bpf_object__pin_maps() is called with a path argument. Any pin paths set
by bpf_map__set_pin_path() are unaffected, and it will still be up to the
caller to avoid invalid characters in those.
Fixes: 113e6b7e15 ("libbpf: Sanitise internal map names so they are not rejected by the kernel")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20201203093306.107676-1-toke@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0178297c1e ]
On PREEMPT_RT enabled kernels unmarked hrtimers are moved into soft
interrupt expiry mode by default.
The IIO hrtimer-trigger needs to run in hard interrupt context since it
will end up calling generic_handle_irq() which has the requirement to run
in hard interrupt context.
Explicitly specify that the timer needs to run in hard interrupt context by
using the HRTIMER_MODE_REL_HARD flag.
Fixes: f5c2f0215e ("hrtimer: Move unmarked hrtimers to soft interrupt expiry on RT")
Reported-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20201117103751.16131-1-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0263bbb377 ]
The PMU group constraints mask for threshold events covers
all thresholding bits which includes threshold control value
(start/stop), select value as well as thresh_cmp value (MMCRA[9:18].
In power9, thresh_cmp bits were part of the event code. But in case
of power10, thresh_cmp bits are not part of event code due to
inclusion of MMCR3 bits. Hence thresh_cmp is not valid for
group constraints for power10.
Fix the PMU group constraints checking for threshold events in
power10 by using constraint mask and value for only threshold control
and select bits.
Fixes: a64e697cef ("powerpc/perf: power10 Performance Monitoring support")
Signed-off-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1606409684-1589-4-git-send-email-atrajeev@linux.vnet.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e924be7b0b ]
In Power9, L2/L3 bus events are always available as a
"bank" of 4 events. To obtain the counts for any of the
l2/l3 bus events in a given bank, the user will have to
program PMC4 with corresponding l2/l3 bus event for that
bank.
Commit 59029136d7 ("powerpc/perf: Add constraints for power9 l2/l3 bus events")
enforced this rule in Power9. But this is not valid for
Power10, since in Power10 Monitor Mode Control Register2
(MMCR2) has bits to configure l2/l3 event bits. Hence remove
this PMC4 constraint check from power10.
Since the l2/l3 bits in MMCR2 are not per-pmc, patch handles
group constrints checks for l2/l3 bits in MMCR2.
Fixes: a64e697cef ("powerpc/perf: power10 Performance Monitoring support")
Signed-off-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1606409684-1589-3-git-send-email-atrajeev@linux.vnet.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3afd28cd2 ]
power10 uses bit 9 of the raw event code as RADIX_SCOPE_QUAL.
This bit is used for enabling the radix process events.
Patch fixes the PMU counter support functions to program bit
18 of MMCR1 ( Monitor Mode Control Register1 ) with the
RADIX_SCOPE_QUAL bit value. Since this field is not per-pmc,
add this to PMU group constraints to make sure events in a
group will have same bit value for this field. Use bit 21 as
constraint bit field for radix_scope_qual. Patch also updates
the power10 raw event encoding layout information, format field
and constraints bit layout to include the radix_scope_qual bit.
Fixes: a64e697cef ("powerpc/perf: power10 Performance Monitoring support")
Signed-off-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1606409684-1589-2-git-send-email-atrajeev@linux.vnet.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe18a35e68 ]
Commit 63ce271b5e ("powerpc/prom: convert PROM_BUG() to standard
trap") added an EMIT_BUG_ENTRY for the trap after the branch to
start_kernel(). The EMIT_BUG_ENTRY was for the address "0b", however the
trap was not labeled with "0". Hence the address used for bug is in
relative_toc() where the previous "0" label is. Label the trap as "0" so
the correct address is used.
Fixes: 63ce271b5e ("powerpc/prom: convert PROM_BUG() to standard trap")
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201130004404.30953-1-jniethe5@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f75e7d73bd ]
On systems without any specific PMU driver support registered, running
'perf record' with —intr-regs will crash ( perf record -I <workload> ).
The relevant portion from crash logs and Call Trace:
Unable to handle kernel paging request for data at address 0x00000068
Faulting instruction address: 0xc00000000013eb18
Oops: Kernel access of bad area, sig: 11 [#1]
CPU: 2 PID: 13435 Comm: kill Kdump: loaded Not tainted 4.18.0-193.el8.ppc64le #1
NIP: c00000000013eb18 LR: c000000000139f2c CTR: c000000000393d80
REGS: c0000004a07ab4f0 TRAP: 0300 Not tainted (4.18.0-193.el8.ppc64le)
NIP [c00000000013eb18] is_sier_available+0x18/0x30
LR [c000000000139f2c] perf_reg_value+0x6c/0xb0
Call Trace:
[c0000004a07ab770] [c0000004a07ab7c8] 0xc0000004a07ab7c8 (unreliable)
[c0000004a07ab7a0] [c0000000003aa77c] perf_output_sample+0x60c/0xac0
[c0000004a07ab840] [c0000000003ab3f0] perf_event_output_forward+0x70/0xb0
[c0000004a07ab8c0] [c00000000039e208] __perf_event_overflow+0x88/0x1a0
[c0000004a07ab910] [c00000000039e42c] perf_swevent_hrtimer+0x10c/0x1d0
[c0000004a07abc50] [c000000000228b9c] __hrtimer_run_queues+0x17c/0x480
[c0000004a07abcf0] [c00000000022aaf4] hrtimer_interrupt+0x144/0x520
[c0000004a07abdd0] [c00000000002a864] timer_interrupt+0x104/0x2f0
[c0000004a07abe30] [c0000000000091c4] decrementer_common+0x114/0x120
When perf record session is started with "-I" option, capturing registers
on each sample calls is_sier_available() to check for the
SIER (Sample Instruction Event Register) availability in the platform.
This function in core-book3s accesses 'ppmu->flags'. If a platform specific
PMU driver is not registered, ppmu is set to NULL and accessing its
members results in a crash. Fix the crash by returning false in
is_sier_available() if ppmu is not set.
Fixes: 333804dc3b ("powerpc/perf: Update perf_regs structure to include SIER")
Reported-by: Sachin Sant <sachinp@linux.vnet.ibm.com>
Signed-off-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1606185640-1720-1-git-send-email-atrajeev@linux.vnet.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e4d86e241 ]
The "a->index" value comes from the user via the ioctl. The problem is
that the shift can wrap resulting in setting "mxb->cur_audinput" to an
invalid value, which later results in an array overflow.
Fixes: 6680427791 ("[media] mxb: fix audio handling")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89ff600503 ]
In case of retrying fill_super with skip_recovery,
s_encoding for casefold would not be loaded again even though it's
already been freed because it's not NULL.
Set NULL after free to prevent double freeing when unmount.
Fixes: eca4873ee1 ("f2fs: Use generic casefolding support")
Signed-off-by: Hyeongseok Kim <hyeongseok@gmail.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bce776f100 ]
pm_runtime_get_sync will increment pm usage counter
even it failed. Forgetting to putting operation will
result in reference leak here. We fix it by replacing
it with pm_runtime_resume_and_get to keep usage counter
balanced. It depends on the mainline commit[PM: runtime:
Add pm_runtime_resume_and_get to deal with usagecounter].
Fixes: 323aeb0eb5 ("hwmon: (ina3221) Add PM runtime support")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201202145320.1135614-1-zhangqilong3@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b06a56d46 ]
commit f8f6ae5d07 ("mm: always have io_remap_pfn_range() set
pgprot_decrypted()") allows drivers using mmap to put PCI memory mapped
BAR space into userspace to work correctly on AMD SME systems that default
to all memory encrypted.
Since vfio_pci_mmap_fault() is working with PCI memory mapped BAR space it
should be calling io_remap_pfn_range() otherwise it will not work on SME
systems.
Fixes: 11c4cd07ba ("vfio-pci: Fault mmaps to enable vma tracking")
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Peter Xu <peterx@redhat.com>
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf701b765e ]
nfsiod is currently a concurrency-managed workqueue (CMWQ).
This means that workitems scheduled to nfsiod on a given CPU are queued
behind all other work items queued on any CMWQ on the same CPU. This
can introduce unexpected latency.
Occaionally nfsiod can even cause excessive latency. If the work item
to complete a CLOSE request calls the final iput() on an inode, the
address_space of that inode will be dismantled. This takes time
proportional to the number of in-memory pages, which on a large host
working on large files (e.g.. 5TB), can be a large number of pages
resulting in a noticable number of seconds.
We can avoid these latency problems by switching nfsiod to WQ_UNBOUND.
This causes each concurrent work item to gets a dedicated thread which
can be scheduled to an idle CPU.
There is precedent for this as several other filesystems use WQ_UNBOUND
workqueue for handling various async events.
Signed-off-by: NeilBrown <neilb@suse.de>
Fixes: ada609ee2a ("workqueue: use WQ_MEM_RECLAIM instead of WQ_RESCUER")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b82d88d59 ]
NLM uses an interval-based rebinding, i.e. it clears the transport's
binding under certain conditions if more than 60 seconds have elapsed
since the connection was last bound.
This rebinding is not necessary for an autobind RPC client over a
connection-oriented protocol like TCP.
It can also cause problems: it is possible for nlm_bind_host() to clear
XPRT_BOUND whilst a connection worker is in the middle of trying to
reconnect, after it had already been checked in xprt_connect().
When the connection worker notices that XPRT_BOUND has been cleared
under it, in xs_tcp_finish_connecting(), that results in:
xs_tcp_setup_socket: connect returned unhandled error -107
Worse, it's possible that the two can get into lockstep, resulting in
the same behaviour repeated indefinitely, with the above error every
300 seconds, without ever recovering, and the connection never being
established. This has been seen in practice, with a large number of NLM
client tasks, following a server restart.
The existing callers of nlm_bind_host & nlm_rebind_host should not need
to force the rebind, for TCP, so restrict the interval-based rebinding
to UDP only.
For TCP, we will still rebind when needed, e.g. on timeout, and connection
error (including closure), since connection-related errors on an existing
connection, ECONNREFUSED when trying to connect, and rpc_check_timeout(),
already unconditionally clear XPRT_BOUND.
To avoid having to add the fix, and explanation, to both nlm_bind_host()
and nlm_rebind_host(), remove the duplicate code from the former, and
have it call the latter.
Drop the dprintk, which adds no value over a trace.
Signed-off-by: Calum Mackay <calum.mackay@oracle.com>
Fixes: 35f5a422ce ("SUNRPC: new interface to force an RPC rebind")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 35a6d39672 ]
'snprintf' returns the number of characters which would have been written
if enough space had been available, excluding the terminating null byte.
Thus, the return value of 'sizeof(buf)' means that the last character
has been dropped.
Signed-off-by: Fedor Tokarev <ftokarev@gmail.com>
Fixes: 2f34b8bfae ("SUNRPC: add links for all client xprts to debugfs")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5aa6b22e2 ]
According to RFC5666, the correct netid for an IPv6 addressed RDMA
transport is "rdma6", which we've supported as a mount option since
Linux-4.7. The problem is when we try to load the module "xprtrdma6",
that will fail, since there is no modulealias of that name.
Fixes: 181342c5eb ("xprtrdma: Add rdma6 option to support NFS/RDMA IPv6")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05ad917561 ]
Currently, the client will always ask for security_labels if the server
returns that it supports that feature regardless of any LSM modules
(such as Selinux) enforcing security policy. This adds performance
penalty to the READDIR operation.
Client adjusts superblock's support of the security_label based on
the server's support but also current client's configuration of the
LSM modules. Thus, prior to using the default bitmask in READDIR,
this patch checks the server's capabilities and then instructs
READDIR to remove FATTR4_WORD2_SECURITY_LABEL from the bitmask.
v5: fixing silly mistakes of the rushed v4
v4: simplifying logic
v3: changing label's initialization per Ondrej's comment
v2: dropping selinux hook and using the sb cap.
Suggested-by: Ondrej Mosnacek <omosnace@redhat.com>
Suggested-by: Scott Mayhew <smayhew@redhat.com>
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Fixes: 2b0143b5c9 ("VFS: normal filesystems (and lustre): d_inode() annotations")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e4c72201b6 ]
Currently, we wake up the tasks by priority queue ordering, which means
that we ignore the batching that is supposed to help with QoS issues.
Fixes: c049f8ea9a ("SUNRPC: Remove the bh-safe lock requirement on the rpc_wait_queue->lock")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7cee9c0f4 ]
The wmi service available event has been
extended to contain extra 128 bit for new services
to be indicated by firmware.
Currently the presence of any optional TLVs in
the wmi service available event leads to a parsing
error with the below error message:
ath10k_snoc 18800000.wifi: failed to parse svc_avail tlv: -71
The wmi service available event parsing should
not return error for the newly added optional TLV.
Fix this parsing for service available event message.
Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.2.2-00720-QCAHLSWMTPL-1
Fixes: cea19a6ce8 ("ath10k: add WMI_SERVICE_AVAILABLE_EVENT support")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1605501291-23040-1-git-send-email-pillair@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5da7acfec5 ]
It was observed that the codepath for the ATH11K_SKB_HW_80211_ENCAP was
used even when the IEEE80211_TX_CTRL_HW_80211_ENCAP was not enabled for a
an skbuff. This became even more prominent when the QCAs wlan-open patchset
for ath11k [1] was applied and a sane looking fix just caused crashes when
injecting frames via a monitor interface (for example with ratechecker):
[ 86.963152] Unable to handle kernel NULL pointer dereference at virtual address 00000338
[ 86.963192] pgd = ffffffc0008f0000
[ 86.971034] [00000338] *pgd=0000000051706003, *pud=0000000051706003, *pmd=0000000051707003, *pte=00e800000b000707
[ 86.984292] Internal error: Oops: 96000006 [#1] PREEMPT SMP
[...]
[ 87.713339] [<ffffffbffc802480>] ieee80211_tx_status_8023+0xf8/0x220 [mac80211]
[ 87.715654] [<ffffffbffc98bad4>] ath11k_dp_tx_completion_handler+0x42c/0xa10 [ath11k]
[ 87.722924] [<ffffffbffc989190>] ath11k_dp_service_srng+0x70/0x3c8 [ath11k]
[ 87.730831] [<ffffffbffca03460>] 0xffffffbffca03460
[ 87.737599] [<ffffffc00046ef58>] net_rx_action+0xf8/0x288
[ 87.742462] [<ffffffc000097554>] __do_softirq+0xfc/0x220
[ 87.748014] [<ffffffc000097900>] irq_exit+0x98/0xe8
[ 87.753396] [<ffffffc0000cf188>] __handle_domain_irq+0x90/0xb8
[ 87.757999] [<ffffffc000081ca4>] gic_handle_irq+0x6c/0xc8
[ 87.763899] Exception stack(0xffffffc00081bdc0 to 0xffffffc00081bef0)
Problem is that the state of ath11k_skb_cb->flags must be considered
unknown and could contain anything when it is not manually initialized. So
it could also contain ATH11K_SKB_HW_80211_ENCAP. And this can result in the
code to assume that the ath11k_skb_cb->vif is set - even when this is not
always the case for non ATH11K_SKB_HW_80211_ENCAP transmissions.
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.4.0.1.r1-00026-QCAHKSWPL_SILICONZ-2
[1] https://source.codeaurora.org/quic/qsdk/oss/system/feeds/wlan-open/tree/mac80211/patches?h=NHSS.QSDK.11.4.r3
(162 patches at the moment which are often not upstreamed but essential
to get ath11k working)
Fixes: e7f33e0c52 ("ath11k: add tx hw 802.11 encapsulation offloading support")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201119154235.263250-2-sven@narfation.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f4d291b43f ]
The driver_data area of ieee80211_tx_info is used in ath11k for
ath11k_skb_cb. The first function in the TX patch which rewrites it to
ath11k_skb_cb is already ath11k_mac_op_tx. No one else in the code path
must use it for something else before it reinitializes it. Otherwise the
data has to be considered uninitialized or corrupt.
But the ieee80211_tx_info.control shares exactly the same area as
ieee80211_tx_info.driver_data and ath11k is still using it. This results in
best case in a
ath11k c000000.wifi1: no vif found for mgmt frame, flags 0x0
or (slightly worse) in a kernel oops.
Instead, the interesting data must be moved first into the ath11k_skb_cb
and ieee80211_tx_info.control must then not be used anymore.
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.4.0.1.r1-00026-QCAHKSWPL_SILICONZ-2
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201119154235.263250-1-sven@narfation.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ed36ecd14 ]
To comply with the intended usage of the V4L2 selection target when
used to retrieve a sensor image properties, adjust the rectangles
returned by the imx219 driver.
The top/left crop coordinates of the TGT_CROP rectangle were set to
(0, 0) instead of (8, 8) which is the offset from the larger physical
pixel array rectangle. This was also a mismatch with the default values
crop rectangle value, so this is corrected. Found with v4l2-compliance.
While at it, add V4L2_SEL_TGT_CROP_BOUNDS support: CROP_DEFAULT and
CROP_BOUNDS have the same size as the non-active pixels are not readable
using the selection API. Found with v4l2-compliance.
[reword commit message, use macros for pixel offsets]
Fixes: e6d4ef7d58 ("media: i2c: imx219: Implement get_selection")
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7fe1d4453f ]
The MAX9271 GPIO1 line that controls the sensor reset is by default
enabled after a serializer chip reset.
As rdacm20 does not go through an explicit serializer reset, make sure
GPIO1 is enabled to make the camera module driver more robust.
Fixes: 34009bffc1 ("media: i2c: Add RDACM20 driver")
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e04e60fce4 ]
The 'master' device acts as a glue layer used during bus
initialization only, and it needs to be 'transparent' for pm_runtime
management. Its behavior should be that it becomes active when one of
its children becomes active, and suspends when all of its children are
suspended.
In our tests on Intel platforms, we routinely see these sort of
warnings on the initial boot:
[ 21.447345] rt715 sdw:3:25d:715:0: runtime PM trying to activate
child device sdw:3:25d:715:0 but parent (sdw-master-3) is not active
This is root-caused to a missing setup to make the device 'active' on
probe. Since we don't want the device to remain active forever after
the probe, the autosuspend configuration is also enabled at the end of
the probe - the device will actually autosuspend only in the case
where there are no devices physically attached. In practice, the
master device will suspend when all its children are no longer active.
Fixes: bd84256e86 ('soundwire: master: enable pm runtime')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20201124130742.10986-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9905f728b0 ]
The mhu_db_channel info is allocated per channel using devm_kzalloc from
mhu_db_mbox_xlate which gets called from mbox_request_channel. However
we are releasing the allocated mhu_db_channel info using plain kfree from
mhu_db_shutdown which is called from mbox_free_channel.
This leads to random crashes when the channel is freed like below one:
Unable to handle kernel paging request at virtual address 0080000400000008
[0080000400000008] address between user and kernel address ranges
Internal error: Oops: 96000044 [#1] PREEMPT SMP
Modules linked in: scmi_module(-)
CPU: 1 PID: 2212 Comm: rmmod Not tainted 5.10.0-rc5 #31
Hardware name: ARM LTD ARM Juno Development Platform/ARM Juno
Development Platform, BIOS EDK II Nov 19 2020
pstate: 20000085 (nzCv daIf -PAN -UAO -TCO BTYPE=--)
pc : release_nodes+0x74/0x230
lr : devres_release_all+0x40/0x68
Call trace:
release_nodes+0x74/0x230
devres_release_all+0x40/0x68
device_release_driver_internal+0x12c/0x1f8
driver_detach+0x58/0xe8
bus_remove_driver+0x64/0xe0
driver_unregister+0x38/0x68
platform_driver_unregister+0x1c/0x28
scmi_driver_exit+0x38/0x44 [scmi_module]
__arm64_sys_delete_module+0x188/0x260
el0_svc_common.constprop.0+0x80/0x1a8
do_el0_svc+0x2c/0x98
el0_sync_handler+0x160/0x168
el0_sync+0x174/0x180
Code: 1400000d eb07009f 54000460 f9400486 (f90004a6)
---[ end trace c55ffd306c140233 ]---
Fix it by replacing kfree with devm_kfree as required.
Fixes: 7002ca237b ("mailbox: arm_mhu: Add ARM MHU doorbell driver")
Reported-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Cristian Marussi <cristian.marussi@arm.com>
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d34895c319 ]
Page alignment is required when setting the number of extended sge
according to the hardware's achivement. If the space of needed extended
sge is greater than one page, the roundup_pow_of_two() can ensure
that. But if the needed extended sge isn't 0 and can not be filled in a
whole page, the driver should align it specifically.
Fixes: 54d6638765 ("RDMA/hns: Optimize WQE buffer size calculating process")
Link: https://lore.kernel.org/r/1606558959-48510-3-git-send-email-liweihang@huawei.com
Signed-off-by: Yangyang Li <liyangyang20@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89bbcaac3d ]
Second stage bootloaders prior to Linux boot may use all inbound windows
including IARR1/IMAP1. We need to ensure that all previous configuration
of inbound windows are invalidated during the initialization stage of
the Linux iProc PCIe driver so let's add a fix to define and invalidate
IARR1/IMAP1 because it is currently missing, fixing the issue.
Link: https://lore.kernel.org/r/20201001060054.6616-3-srinath.mannam@broadcom.com
Fixes: 9415743e4c ("PCI: iproc: Invalidate PAXB address mapping")
Signed-off-by: Roman Bacik <roman.bacik@broadcom.com>
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc73eb321d ]
The shift of 1 by align_order is evaluated using 32 bit arithmetic and the
result is assigned to a resource_size_t type variable that is a 64 bit
unsigned integer on 64 bit platforms. Fix an overflow before widening issue
by making the 1 a ULL.
Addresses-Coverity: ("Unintentional integer overflow")
Fixes: 32a9a682be ("PCI: allow assignment of memory resources with a specified alignment")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11d0e4f281 ]
The numbering of the i2c busses differs from ACPI and a number of typos
was made in the original patch. Further more the irq flags for the
various resources was not correct and i2c3 only has one of the two
client devices active in any one device.
Also label the various devices, for easier comparison with the ACPI
tables.
Tested-by: Steev Klimaszewski <steev@kali.org>
Fixes: 44acee2078 ("arm64: dts: qcom: Add Lenovo Yoga C630")
Link: https://lore.kernel.org/r/20201130165924.319708-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91ab1c1228 ]
The upstream port, doesn't really follow the vendor partitioning. The
bootloader partition has one U-Boot FIT image containing all needed
bits and pieces. Even today the bootloader is already larger than the
current "bootloader" partition. Thus, fold all the partitions into one
and keep the environment one. The latter is still valid.
We keep the failsafe partitions because the first half of the SPI flash
is preinstalled by the vendor and immutable.
Fixes: 815364d042 ("arm64: dts: freescale: add Kontron sl28 support")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 588b17eda1 ]
On the LS1028A the FlexSPI clock is connected to the first HWA output,
see Figure 7 "Clock subsystem block diagram".
Fixes: c77fae5ba0 ("arm64: dts: ls1028a: Add FlexSPI support")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d0570a575a ]
On the LS1028A the ENETC reference clock is connected to 4th HWA output,
see Figure 7 "Clock subsystem block diagram".
The PHC may run with a wrong frequency. ptp_qoriq_auto_config() will read
the clock speed of the clock given in the device tree. It is likely that,
on the reference board this wasn't noticed because both clocks have the
same frequency. But this must not be always the case. Fix it.
Fixes: 49401003e2 ("arm64: dts: fsl: ls1028a: add ENETC 1588 timer node")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4615fbc378 ]
When an interrupt allocation fails for N interrupts, it is pretty
common for the error handling code to free the same number of interrupts,
no matter how many interrupts have actually been allocated.
This may result in the domain freeing code to be unexpectedly called
for interrupts that have no mapping in that domain. Things end pretty
badly.
Instead, add some checks to irq_domain_free_irqs_hierarchy() to make sure
that thiss does not follow the hierarchy if no mapping exists for a given
interrupt.
Fixes: 6a6544e520 ("genirq/irqdomain: Remove auto-recursive hierarchy support")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20201129135551.396777-1-maz@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2f6cb78ea ]
pm_runtime_get_sync will increment pm usage counter even it
failed. Forgetting to call pm_runtime_put_noidle will result
in reference leak in callers(bq24190_sysfs_show,
bq24190_charger_get_property, bq24190_charger_set_property,
bq24190_battery_get_property, bq24190_battery_set_property),
so we should fix it.
Fixes: f385e6e2a1 ("power: bq24190_charger: Use PM runtime autosuspend")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a0f1ccd96c ]
Commit 9c80662a74 ("power: supply: axp288_charger: Add special handling
for HP Pavilion x2 10") added special handling for HP Pavilion x2 10
models which use the weird combination of a Type-C connector and the
non Type-C aware AXP288 PMIC.
This special handling was activated by a DMI match a the product-name
of "HP Pavilion x2 Detachable". Recently I've learned that there are
also older "HP Pavilion x2 Detachable" models with an AXP288 PMIC +
a micro-usb connector where we should not activate the special handling
for the Type-C connectors.
Extend the matching to also match on the DMI board-name and match on the
2 boards (one Bay Trail based one Cherry Trail based) of which we are
certain that they use the AXP288 + Type-C connector combination.
Note the DSDT code from these older (AXP288 + micro-USB) models contains
some AML code (which never runs under Linux) which reads the micro-USB
connector id-pin and if it is pulled to ground, which would normally mean
the port is in host mode!, then it sets the input-current-limit to 3A,
it seems HP is using the micro-USB port as a charging only connector
and identifies their own 3A capable charger though this hack which is a
major violation of the USB specs. Note HP also hardcodes a 2A limit
when the id-pin is not pulled to ground, which is also in violation
of the specs.
I've no intention to add support for HP's hack to support 3A charging
on these older models. By making the DMI matches for the Type-C equipped
models workaround more tighter, these older models will be treated just
like any other AXP288 + micro-USB equipped device and the input-current
limit will follow the BC 1.2 spec (using the defacto standard values
there where the BC 1.2 spec defines a range).
Fixes: 9c80662a74 ("power: supply: axp288_charger: Add special handling for HP Pavilion x2 10")
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1896924
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f24479ead ]
The switches with integrated CPUs have only got a single i2c controller.
They incorrectly gained one when they were split from the Armada-XP.
Fixes: 43e28ba877 ("ARM: dts: Use armada-370-xp as a base for armada-xp-98dx3236")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 41fff6e19b ]
In current code, it jumps to ida_simple_remove() when ida_simple_get()
failes to allocate an ID. Just return to fix it.
Fixes: 0fae198988 ("HSI: omap_ssi: built omap_ssi and omap_ssi_port into one module")
Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 414562b0ef ]
Aliases property name must include only lowercase and '-', so fix this
in the driver, so we're not tempted to do "ovl_2l0 = &ovl_2l0" in the
device-tree instead of the right one which is "ovl-2l0 = &ovl_2l0".
Fixes: b17bdd0d7a ("drm/mediatek: add component OVL_2L0")
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b47a98efa9 ]
Device memory (DM) are registered as MR during initialization flow, these
MRs were not tracked by resource tracker and had res->valid set as a
false. Update the code to manage them too.
Before this change:
$ ibv_rc_pingpong -j &
$ rdma res show mr <-- shows nothing
After this change:
$ ibv_rc_pingpong -j &
$ rdma res show mr
dev ibp0s9 mrn 0 mrlen 4096 pdn 3 pid 734 comm ibv_rc_pingpong
Fixes: be934cca9e ("IB/uverbs: Add device memory registration ioctl support")
Link: https://lore.kernel.org/r/20201117070148.1974114-2-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b1b0cb063 ]
This is supposed to return negative error codes but the type is bool so
it returns true instead.
Fixes: b47b79d8a2 ("[media] media: i2c: max2175: Add MAX2175 support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eeb76afbe8 ]
Stop video streaming when requested.
When s_stream is called to stop the video streaming, if/else condition calls
start_streaming function instead of the one for stopping it.
Fixes: 4361905962 ("media: imx214: Add imx214 camera sensor driver")
Signed-off-by: Daniel Gomez <daniel@qtec.com>
Signed-off-by: Ricardo Ribalda <ribalda@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0afe0a998c ]
Currently, lwt_len_hist's map lwt_len_hist_map is uses pinning, and the
map isn't cleared on test end. This leds to reuse of that map for
each test, which prevents the results of the test from being accurate.
This commit fixes the problem by removing of pinned map from bpffs.
Also, this commit add the executable permission to shell script
files.
Fixes: f74599f7c5 ("bpf: Add tests and samples for LWT-BPF")
Signed-off-by: Daniel T. Lee <danieltimlee@gmail.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20201124090310.24374-7-danieltimlee@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 912b341585 ]
Remove PSU EEPROM configuration for systems class equipped with
Mellanox chip Spectrum and ATOM CPU - system types MSN274x. Till now
all the systems from this class used few types of power units, all
equipped with EEPROM device with address space two bytes. Thus, all
these devices have been handled by EEPROM driver "24c02".
There is a new requirement is to support power unit replacement by "off
the shelf" device, matching electrical required parameters. Such device
can be equipped with different EEPROM type, which could be one byte
address space addressing or even could be not equipped with EEPROM.
In such case "24c02" will not work.
Fixes: ef08e14a3 ("platform/x86: mlx-platform: Add support for new msn274x system type")
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20201125101056.174708-3-vadimp@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2bf5046bdb ]
Remove PSU EEPROM configuration for systems class equipped with
Mellanox chip Spectrum and Celeron CPU - system types MSN2700, MSN2100.
Till now all the systems from this class used few types of power units,
all equipped with EEPROM device with address space two bytes. Thus, all
these devices have been handled by EEPROM driver "24c02".
There is a new requirement is to support power unit replacement by "off
the shelf" device, matching electrical required parameters. Such device
can be equipped with different EEPROM type, which could be one byte
address space addressing or even could be not equipped with EEPROM.
In such case "24c02" will not work.
Fixes: c6acad68e ("platform/mellanox: mlxreg-hotplug: Modify to use a regmap interface")
Fixes: ba814fdd0 ("platform/x86: mlx-platform: Use defines for bus assignment")
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20201125101056.174708-2-vadimp@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit abf287eeff ]
When dvb_create_media_graph fails, the debugfs kept inside client should
be released. However, the current implementation does not release them.
Fix this by adding a new goto label to call smsdvb_debugfs_release.
Fixes: 0d3ab8410d ("[media] dvb core: must check dvb_create_media_graph()")
Signed-off-by: Keita Suzuki <keitasuzuki.park@sslab.ics.keio.ac.jp>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59cb403f38 ]
DCSS supports 90/180/270 degree rotations for Vivante tiled and super-tiled
formats. Unfortunately, with the current code, they didn't work properly.
This simple patch makes the rotations work by fixing the way the scaler is set
up for 90/270 degree rotations. In this particular case, the source width and
height need to be swapped since DPR is sending the buffer to scaler already
rotated.
Also, make sure to allow full rotations for DRM_FORMAT_MOD_VIVANTE_SUPER_TILED.
Fixes: 9021c317b7 ("drm/imx: Add initial support for DCSS on iMX8MQ")
Signed-off-by: Laurentiu Palcu <laurentiu.palcu@oss.nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20201105140127.25249-2-laurentiu.palcu@oss.nxp.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 47edc0104c ]
Commit 5bd773242f ("soundwire: qcom: avoid dependency on
CONFIG_SLIMBUS") removed hard dependency on Slimbus for qcom driver but
it results in build failure when: CONFIG_SOUNDWIRE_QCOM=y
CONFIG_SLIMBUS=m
drivers/soundwire/qcom.o: In function `qcom_swrm_probe':
qcom.c:(.text+0xf44): undefined reference to `slimbus_bus'
Fix this by using IS_REACHABLE() in driver which is recommended to be
used with imply.
Fixes: 5bd773242f ("soundwire: qcom: avoid dependency on CONFIG_SLIMBUS")
Reported-by: kernel test robot <lkp@intel.com>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Link: https://lore.kernel.org/r/20201125055155.GD8403@vkoul-mobl
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd37d2f59e ]
rdma_detroy_id() cannot be called under &lock - we must instead keep the
error'd ID around until &lock can be released, then destroy it.
This is complicated by the usual way listen IDs are destroyed through
cma_process_remove() which can run at any time and will asynchronously
destroy the same ID.
Remove the ID from visiblity of cma_process_remove() before going down the
destroy path outside the locking.
Fixes: c80a0c52d8 ("RDMA/cma: Add missing error handling of listen_id")
Link: https://lore.kernel.org/r/20201118133756.GK244516@ziepe.ca
Reported-by: syzbot+1bc48bf7f78253f664a9@syzkaller.appspotmail.com
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b26c1a034 ]
Fix the device-tree entry that represents I/O High Voltage property
by replacing 'nvidia,io-high-voltage' with 'nvidia,io-hv' as the former
entry is deprecated.
Fixes: dbb72e2c30 ("arm64: tegra: Add configuration for PCIe C5 sideband signals")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 98650b0874 ]
LED core does not allow LED_COLOR_ID_MULTI for now and instead for RGB
LEDs prefers LED_COLOR_ID_RGB.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes: 77dce3a22e ("leds: disallow /sys/class/leds/*:multi:* for now")
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d8d014c7d ]
In case of memory allocation failure, we must release some resources as
done in all other error handling paths of the function.
'goto child_out' instead of a direct return so that 'fwnode_handle_put()'
is called when we break out of a 'device_for_each_child_node' loop.
Fixes: 242b81170f ("leds: lp50xx: Add the LP50XX family of the RGB LED driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 311066aa9e ]
if of_find_device_by_node() succeed, netxbig_leds_get_of_pdata() doesn't
have a corresponding put_device(). Thus add jump target to fix the
exception handling for this function implementation.
Fixes: 2976b17989 ("leds: netxbig: add device tree binding")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a31eb61564 ]
ezusb_xmit() allocates a context which is leaked if
orinoco_process_xmit_skb() returns an error.
Move ezusb_alloc_ctx() after the invocation of
orinoco_process_xmit_skb() because the context is not needed so early.
ezusb_access_ltv() will cleanup the context in case of an error.
Fixes: bac6fafd4d ("orinoco: refactor xmit path")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201113212252.2243570-2-bigeasy@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11af6de479 ]
Set the rx_filter in ath11k_mac_config_mon_status_default(),
only when the rx_filter value exists in ath11k_debug_rx_filter().
Without this change, rx_filter gets set to 0 and peer rssi stats
aren't updating properly from firmware.
Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01230-QCAHKSWPL_SILICONZ-4
Fixes: ec48d28ba2 ("ath11k: Fix rx_filter flags setting for per peer rx_stats")
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1605091117-11005-1-git-send-email-mkenna@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59bbf83835 ]
In omap4_keypad_probe, the patch fix several bugs.
1) pm_runtime_get_sync will increment pm usage counter even it
failed. Forgetting to pm_runtime_put_noidle will result in
reference leak.
2) In err_unmap, forget to disable runtime of device,
pm_runtime_enable will increase power disable depth. Thus a
pairing decrement is needed on the error handling path to keep
it balanced.
3) In err_pm_disable, it will call pm_runtime_put_sync twice not
one time.
To fix this we factor out code reading revision and disabling touchpad, and
drop PM reference once we are done talking to the device.
Fixes: f77621cc64 ("Input: omap-keypad - dynamically handle register offsets")
Fixes: 5ad567ffba ("Input: omap4-keypad - wire up runtime PM handling")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201120133918.2559681-1-zhangqilong3@huawei.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a161ffe4b8 ]
clang static analysis reports this problem
pdr_interface.c:596:6: warning: Branch condition evaluates
to a garbage value
if (!req.service_path[0])
^~~~~~~~~~~~~~~~~~~~
This check that req.service_path was set in an earlier loop.
However req is a stack variable and its initial value
is undefined.
So initialize req to 0.
Fixes: fbe639b44a ("soc: qcom: Introduce Protection Domain Restart helpers")
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20200819184637.15648-1-trix@redhat.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b4fa73358c ]
The patch fix two reference leak.
1) pm_runtime_get_sync will increment pm usage counter even it
failed. Forgetting to call put operation will result in
reference leak.
2) The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced.
We fix it by: 1) adding call pm_runtime_put_noidle or
pm_runtime_put_sync in error handling. 2) adding pm_runtime_disable
in error handling, to keep usage counter and disable depth balanced.
Fixes: 88139ed030 ("soc: ti: add Keystone Navigator DMA support")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec8684847d ]
pm_runtime_get_sync will increment pm usage counter even it
failed. Forgetting to pm_runtime_put_noidle will result in
reference leak in knav_queue_probe, so we should fix it.
Fixes: 41f93af900 ("soc: ti: add Keystone Navigator QMSS driver")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 440408dbad ]
Consider an spi driver with a .probe but without a .remove callback (e.g.
rtc-ds1347). The function spi_drv_probe() is called to bind a device and
so dev_pm_domain_attach() is called. As there is no remove callback
spi_drv_remove() isn't called at unbind time however and so calling
dev_pm_domain_detach() is missed and the pm domain keeps active.
To fix this always use both spi_drv_probe() and spi_drv_remove() and
make them handle the respective callback not being set. This has the
side effect that for a (hypothetical) driver that has neither .probe nor
remove the clk and pm domain setup is done.
Fixes: 33cf00e570 ("spi: attach/detach SPI device to the ACPI power domain")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20201119161604.2633521-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 732b764099 ]
This patch fixes the following smatch warnings:
drivers/crypto/allwinner/sun8i-ce/sun8i-ce-hash.c:412
sun8i_ce_hash_run() warn: possible memory leak of 'result'
Note: "buf" is leaked as well.
Furthermore, in case of ENOMEM, crypto_finalize_hash_request() was not
called which was an error.
Fixes: 56f6d5aee8 ("crypto: sun8i-ce - support hash algorithms")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff81072003 ]
The pm_runtime_enable will increase power disable depth.
Thus a pairing decrement is needed on the error handling
path to keep it balanced according to context.
Fixes: f7b2b5dd6a ("crypto: omap-aes - add error check for pm_runtime_get_sync")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5bdad829c3 ]
Clang warns:
drivers/crypto/amcc/crypto4xx_core.c:921:60: warning: operator '?:' has
lower precedence than '|'; '|' will be evaluated first
[-Wbitwise-conditional-parentheses]
(crypto_tfm_alg_type(req->tfm) == CRYPTO_ALG_TYPE_AEAD) ?
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ ^
drivers/crypto/amcc/crypto4xx_core.c:921:60: note: place parentheses
around the '|' expression to silence this warning
(crypto_tfm_alg_type(req->tfm) == CRYPTO_ALG_TYPE_AEAD) ?
^
)
drivers/crypto/amcc/crypto4xx_core.c:921:60: note: place parentheses
around the '?:' expression to evaluate it first
(crypto_tfm_alg_type(req->tfm) == CRYPTO_ALG_TYPE_AEAD) ?
^
(
1 warning generated.
It looks like this should have been a logical OR so that
PD_CTL_HASH_FINAL gets added to the w bitmask if crypto_tfm_alg_type
is either CRYPTO_ALG_TYPE_AHASH or CRYPTO_ALG_TYPE_AEAD. Change the
operator so that everything works properly.
Fixes: 4b5b79998a ("crypto: crypto4xx - fix stalls under heavy load")
Link: https://github.com/ClangBuiltLinux/linux/issues/1198
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 56292e8609 ]
The current memmory-allocation interface causes the following difficulties
for kvfree_rcu():
a) If built with CONFIG_PROVE_RAW_LOCK_NESTING, the lockdep will
complain about violation of the nesting rules, as in "BUG: Invalid
wait context". This Kconfig option checks for proper raw_spinlock
vs. spinlock nesting, in particular, it is not legal to acquire a
spinlock_t while holding a raw_spinlock_t.
This is a problem because kfree_rcu() uses raw_spinlock_t whereas the
"page allocator" internally deals with spinlock_t to access to its
zones. The code also can be broken from higher level of view:
<snip>
raw_spin_lock(&some_lock);
kfree_rcu(some_pointer, some_field_offset);
<snip>
b) If built with CONFIG_PREEMPT_RT, spinlock_t is converted into
sleeplock. This means that invoking the page allocator from atomic
contexts results in "BUG: scheduling while atomic".
c) Please note that call_rcu() is already invoked from raw atomic context,
so it is only reasonable to expaect that kfree_rcu() and kvfree_rcu()
will also be called from atomic raw context.
This commit therefore defers page allocation to a clean context using the
combination of an hrtimer and a workqueue. The hrtimer stage is required
in order to avoid deadlocks with the scheduler. This deferred allocation
is required only when kvfree_rcu()'s per-CPU page cache is empty.
Link: https://lore.kernel.org/lkml/20200630164543.4mdcf6zb4zfclhln@linutronix.de/
Fixes: 3042f83f19 ("rcu: Support reclaim for head-less object")
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d2098b4440 ]
Kim reported that perf-ftrace made his box unhappy. It turns out that
commit:
ff5c4f5cad ("rcu/tree: Mark the idle relevant functions noinstr")
removed one too many notrace qualifiers, probably due to there not being
a helpful comment.
This commit therefore reinstates the notrace and adds a comment to avoid
losing it again.
[ paulmck: Apply Steven Rostedt's feedback on the comment. ]
Fixes: ff5c4f5cad ("rcu/tree: Mark the idle relevant functions noinstr")
Reported-by: Kim Phillips <kim.phillips@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6dbce04d84 ]
Eugenio managed to tickle #PF from NMI context which resulted in
hitting a WARN in RCU through irqentry_enter() ->
__rcu_irq_enter_check_tick().
However, this situation is perfectly sane and does not warrant an
WARN. The #PF will (necessarily) be atomic and not require messing
with the tick state, so early return is correct. This commit
therefore removes the WARN.
Fixes: aaf2bc50df ("rcu: Abstract out rcu_irq_enter_check_tick() from rcu_nmi_enter()")
Reported-by: "Eugenio Pérez" <eupm90@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8eb456be75 ]
The following call stack prevents clk_gating at every I/O completion. We
can remove the condition, ufshcd_any_tag_in_use(), since clkgating_work
will check it again.
ufshcd_complete_requests(struct ufs_hba *hba)
ufshcd_transfer_req_compl()
__ufshcd_transfer_req_compl()
__ufshcd_release(hba)
if (ufshcd_any_tag_in_use() == 1)
return;
ufshcd_tmc_handler(hba);
blk_mq_tagset_busy_iter();
Note that this still requires work to deal with a potential race condition
when user sets clkgating.delay_ms to very small value. That can cause
preventing clkgating by the check of ufshcd_any_tag_in_use() in gate_work.
Link: https://lore.kernel.org/r/20201117165839.1643377-7-jaegeuk@kernel.org
Fixes: 7252a36030 ("scsi: ufs: Avoid busy-waiting by eliminating tag conflicts")
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8de0c9917c ]
The edac_mce_amd module calls decode_dram_ecc() on AMD Family17h and
later systems. This function is used in amd64_edac_mod to do
system-specific decoding for DRAM ECC errors. The function takes a
"NodeId" as a parameter.
In AMD documentation, NodeId is used to identify a physical die in a
system. This can be used to identify a node in the AMD_NB code and also
it is used with umc_normaddr_to_sysaddr().
However, the input used for decode_dram_ecc() is currently the NUMA node
of a logical CPU. In the default configuration, the NUMA node and
physical die will be equivalent, so this doesn't have an impact.
But the NUMA node configuration can be adjusted with optional memory
interleaving modes. This will cause the NUMA node enumeration to not
match the physical die enumeration. The mismatch will cause the address
translation function to fail or report incorrect results.
Use struct cpuinfo_x86.cpu_die_id for the node_id parameter to ensure the
physical ID is used.
Fixes: fbe63acf62 ("EDAC, mce_amd: Use cpu_to_node() to find the node ID")
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20201109210659.754018-4-Yazen.Ghannam@amd.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 14639a22de ]
With commit 3a6f0fb7b8 ("regmap: irq: Add support to clear ack
registers"), the cpcap interrupts are no longer getting acked properly
leading to a very unresponsive device with CPUs fully loaded spinning
in the threaded IRQ handlers.
To me it looks like the clear_ack commit above actually fixed a long
standing bug in regmap_irq_thread() where we unconditionally acked the
interrupts earlier without considering ack_invert. And the issue with
cpcap started happening as we now also consider ack_invert.
Tim Harvey <tharvey@gateworks.com> tried to fix this issue earlier with
"[PATCH v2] regmap: irq: fix ack-invert", but the reading of the ack
register was considered unnecessary for just ack_invert, and we did not
have clear_ack available yet. As the cpcap irqs worked both with and
without ack_invert earlier because of the unconditional ack, the
problem remained hidden until now.
Also, looks like the earlier v3.0.8 based Motorola Android Linux kernel
does clear_ack style read-clear-write with "ireg_val & ~mreg_val" instead
of just ack_invert style write. So let's switch cpcap to use clear_ack
to fix the issue.
Fixes: 3a6f0fb7b8 ("regmap: irq: Add support to clear ack registers")
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Laxminath Kasam <lkasam@codeaurora.org>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Pavel Machek <pavel@ucw.cz>
Reviewed-By: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d75846ed08 ]
'ret' may be 0 so, dev_err_probe() should be called only when 'ret' is
an error code.
Fixes: 41c9c06c49 ("mfd: stmfx: Simplify with dev_err_probe()")
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de1292817c ]
Currently the Kontron sl28cpld Board Management Controller is found only
on Kontron boards equipped with a Freescale Layerscape SoC. Hence add a
dependency on ARCH_LAYERSCAPE, to prevent asking the user about a driver
for this controller when configuring a kernel without Layerscape support.
Fixes: a538ad229b ("mfd: simple-mfd-i2c: Add sl28cpld support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Michael Walle <michael@walle.cc>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a46328470 ]
htcpld_register_chip_i2c() misses to call i2c_put_adapter() in an error
path. Add the missed function call to fix it.
Fixes: 6048a3dd23 ("mfd: Add HTCPLD driver")
Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78665179e5 ]
On 8xx, we get the following features:
[ 0.000000] cpu_features = 0x0000000000000100
[ 0.000000] possible = 0x0000000000000120
[ 0.000000] always = 0x0000000000000000
This is not correct. As CONFIG_PPC_8xx is mutually exclusive with all
other configurations, the three lines should be equal.
The problem is due to CPU_FTRS_GENERIC_32 which is taken when
CONFIG_BOOK3S_32 is NOT selected. This CPU_FTRS_GENERIC_32 is
pointless because there is no generic configuration supporting
all 32 bits but book3s/32.
Remove this pointless generic features definition to unbreak the
calculation of 'possible' features and 'always' features.
Fixes: 76bc080ef5 ("[POWERPC] Make default cputable entries reflect selected CPU family")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/76a85f30bf981d1aeaae00df99321235494da254.1604426550.git.christophe.leroy@csgroup.eu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7223f5bfc ]
Commit 7053f80d96 ("powerpc/64: Prevent stack protection in early
boot") introduced a couple of uses of __attribute__((optimize)) with
function scope, to disable the stack protector in some early boot
code.
Unfortunately, and this is documented in the GCC man pages [0],
overriding function attributes for optimization is broken, and is only
supported for debug scenarios, not for production: the problem appears
to be that setting GCC -f flags using this method will cause it to
forget about some or all other optimization settings that have been
applied.
So the only safe way to disable the stack protector is to disable it
for the entire source file.
[0] https://gcc.gnu.org/onlinedocs/gcc/Common-Function-Attributes.html
Fixes: 7053f80d96 ("powerpc/64: Prevent stack protection in early boot")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
[mpe: Drop one remaining use of __nostackprotector, reported by snowpatch]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201028080433.26799-1-ardb@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6016df8fe8 ]
The selftests/bpf Makefile includes system include directories from
the host, when building BPF programs. On RISC-V glibc requires that
__riscv_xlen is defined. This is not the case for "clang -target bpf",
which messes up __WORDSIZE (errno.h -> ... -> wordsize.h) and breaks
the build.
By explicitly defining __risc_xlen correctly for riscv, we can
workaround this.
Fixes: 167381f3ea ("selftests/bpf: Makefile fix "missing" headers on build with -idirafter")
Signed-off-by: Björn Töpel <bjorn.topel@gmail.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Luke Nelson <luke.r.nels@gmail.com>
Link: https://lore.kernel.org/bpf/20201118071640.83773-2-bjorn.topel@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b627c25e7 ]
There is double acquisition of the pm_lock from mhi_driver_remove()
function. Remove the read_lock_bh/read_unlock_bh calls for pm_lock
taken during a call to mhi_device_put() as the lock is acquired
within the function already. This will help avoid a potential
kernel panic.
Fixes: 189ff97cca ("bus: mhi: core: Add support for data transfer")
Reported-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03e2c9c782 ]
req->sample[1] is not naturally aligned at word boundary, and therefore we
should use get_unaligned_be16() when accessing it.
Fixes: 3eac5c7e44 ("Input: ads7846 - extend the driver for ads7845 controller support")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 820830ec91 ]
In some rare cases the 32 bit Rt value will overflow if z2 and x is max,
z1 is minimal value and x_plate_ohms is relatively high (for example 800
ohm). This would happen on some screen age with low pressure.
There are two possible fixes:
- make Rt 64bit
- reorder calculation to avoid overflow
The second variant seems to be preferable, since 64 bit calculation on
32 bit system is a bit more expensive.
Fixes: ffa458c1bd ("spi: ads7846 driver")
Co-developed-by: David Jander <david@protonic.nl>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20201113112240.1360-1-o.rempel@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68dd9d89ea ]
Commit 6ee1b77ba3 ("iommu/vt-d: Add svm/sva invalidate function")
introduced intel_iommu_sva_invalidate() when CONFIG_INTEL_IOMMU_SVM.
This function uses the dedicated static variable inv_type_granu_table
and functions to_vtd_granularity() and to_vtd_size().
These parts are unused when !CONFIG_INTEL_IOMMU_SVM, and hence,
make CC=clang W=1 warns with an -Wunused-function warning.
Include these parts conditionally on CONFIG_INTEL_IOMMU_SVM.
Fixes: 6ee1b77ba3 ("iommu/vt-d: Add svm/sva invalidate function")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20201115205951.20698-1-lukas.bulwahn@gmail.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b33340e33a ]
Removing the meson-dw-hdmi module and re-inserting it results in a hang
as the driver writes to HDMITX_TOP_SW_RESET. Similar effects can be seen
when booting with mainline u-boot and using the u-boot provided DT (which
is highly desirable).
The reason for the hang seem to be that the clocks are not always
enabled by the time we enter meson_dw_hdmi_init(). Moving this call
*after* dw_hdmi_probe() ensures that the clocks are enabled.
Fixes: 1374b8375c ("drm/meson: dw_hdmi: add resume/suspend hooks")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201116200744.495826-5-maz@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eff5ce02e1 ]
As per current implementation, video driver is unvoting "videom-mem" path
for last video session during vdec_session_release().
While video playback when we try to suspend device, we see video clock
warnings since votes are already removed during vdec_session_release().
corrected this by putting dummy vote on "video-mem" after last video
session release and unvoting it during suspend.
suspend")
Fixes: 07f8f22a33 ("media: venus: core: remove CNOC voting while device
Signed-off-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e4209b380 ]
The current implementation of scsi_vpd_lun_id() uses the designator length
as an implicit measure of priority. This works most of the time, but not
always. For example, some Hitachi storage arrays return this in VPD 0x83:
VPD INQUIRY: Device Identification page
Designation descriptor number 1, descriptor length: 24
designator_type: T10 vendor identification, code_set: ASCII
associated with the Addressed logical unit
vendor id: HITACHI
vendor specific: 5030C3502025
Designation descriptor number 2, descriptor length: 6
designator_type: vendor specific [0x0], code_set: Binary
associated with the Target port
vendor specific: 08 03
Designation descriptor number 3, descriptor length: 20
designator_type: NAA, code_set: Binary
associated with the Addressed logical unit
NAA 6, IEEE Company_id: 0x60e8
Vendor Specific Identifier: 0x7c35000
Vendor Specific Identifier Extension: 0x30c35000002025
[0x60060e8007c350000030c35000002025]
The current code would use the first descriptor because it's longer than
the NAA descriptor. But this is wrong, the kernel is supposed to prefer NAA
descriptors over T10 vendor ID. Designator length should only be used to
compare designators of the same type.
This patch addresses the issue by separating designator priority and
length.
Link: https://lore.kernel.org/r/20201029170846.14786-1-mwilck@suse.com
Fixes: 9983bed390 ("scsi: Add scsi_vpd_lun_id()")
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 299fe9937d ]
When compiled with CONFIG_HAVE_CLK, the kernel need to get provider for the
clock API. This is usually selected by the platform and the sound drivers
should not really care about this. However COMPILE_TEST is special and the
platform required may not have been selected, leading to this type of
error:
> aiu-encoder-spdif.c:(.text+0x3a0): undefined reference to `clk_set_parent'
Since we need a sane provider of the API with COMPILE_TEST, depends on
COMMON_CLK.
Fixes: 6dc4fa179f ("ASoC: meson: add axg fifo base driver")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20201116172423.546855-1-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e44fb034b0 ]
As per bandwidth table video driver is voting with average bandwidth
for "video-mem" and "cpu-cfg" paths as peak bandwidth is zero
in bandwidth table.
suspend")
Fixes: 07f8f22a33 ("media: venus: core: remove CNOC voting while device
Signed-off-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e8efdb578 ]
Currently video driver is voting for venus0-ebi path during buffer
processing with an average bandwidth of all the instances and
unvoting during session release.
While video streaming when we try to do XO-SD using the command
"echo mem > /sys/power/state command" , device is not entering
to suspend state and from interconnect summary seeing votes for venus0-ebi
Corrected this by voting for venus0-ebi path in venus_runtime_resume()
and unvote during venus_runtime_suspend().
suspend")
Fixes: 07f8f22a33 ("media: venus: core: remove CNOC voting while device
Signed-off-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21926d466e ]
Currently video driver is voting after clk enable and un voting
before clk disable. This is incorrect, video driver should vote
before clk enable and unvote after clk disable.
Corrected this by changing the order of clk enable and clk disable.
suspend")
Fixes: 07f8f22a33 ("media: venus: core: remove CNOC voting while device
Signed-off-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 940727bf22 ]
pm_runtime_get_sync will increment pm usage counter even it
failed. Forgetting to pm_runtime_put_noidle will result in
reference leak in cedrus_start_streaming. We should fix it.
Fixes: d5aecd289b ("media: cedrus: Implement runtime PM")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4cbbe2aaa0 ]
pm_runtime_get_sync will increment pm usage counter even it
failed. Forgetting to pm_runtime_put_noidle will result in
reference imbalance in rkisp1_vb2_start_streaming, so we
should fix it.
Fixes: 56e3b29f9f ("media: staging: rkisp1: add streaming paths")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3cc73d2bf ]
Document that the caller of v4l2_fwnode_endpoint_parse() must init the
fields of struct v4l2_fwnode_endpoint (vep argument) fields.
It used to be that the fields were zeroed by v4l2_fwnode_endpoint_parse
when bus type was set to V4L2_MBUS_UNKNOWN but with recent changes (Fixes:
line below) that no longer makes sense.
Fixes: bb4bba9232 ("media: v4l2-fwnode: Make bus configuration a struct")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27c3943683 ]
mtk_vcodec_release_dec_pm() will be called in two places:
a. mtk_vcodec_init_dec_pm() succeed while mtk_vcodec_probe() return error.
b. mtk_vcodec_dec_remove().
In both cases put_device() call is needed, since of_find_device_by_node()
was called in mtk_vcodec_init_dec_pm() previously.
Thus add put_devices() call in mtk_vcodec_release_dec_pm()
Fixes: 590577a4e5 ("[media] vcodec: mediatek: Add Mediatek V4L2 Video Decoder Driver")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f28a81a3b6 ]
if of_find_device_by_node() succeeds, mtk_jpeg_clk_init() doesn't have
a corresponding put_device(). Thus add put_device() to fix the exception
handling for this function implementation.
Fixes: 648372a87c ("media: platform: Change the call functions of getting/enable/disable the jpeg's clock")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a08ad6339e ]
The are two instances of sizeof() being used incorrectly. The
sizeof(void *) is incorrect because urb_buffer is a char ** pointer,
fix this by using sizeof(*dev->urb_buffer). The sizeof(dma_addr_t *)
is incorrect, it should be sizeof(*dev->urb_dma), which is a dma_addr_t
and not a dma_addr_t *. This errors did not cause any issues because
it just so happens the sizes are the same.
Addresses-Coverity: ("Sizeof not portable (SIZEOF_MISMATCH)")
Fixes: 16427faf28 ("[media] tm6000: Add parameter to keep urb bufs allocated")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 81dbc24147 ]
Instead of having two different ways of expressing the same
sleepability concept, using opposite logic, we can rework the
from_ndo to can_sleep for a more consistent usage.
Fixes: 1800eee166 ("net: ionic: Replace in_interrupt() usage.")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e0243e1966 ]
We should be using the multicast sync routines for the multicast
filters. Also, let's just flatten the logic a bit and pull
the small unicast routine back into ionic_set_rx_mode().
Fixes: 1800eee166 ("net: ionic: Replace in_interrupt() usage.")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4cb773c70 ]
The acpi_get_table() should be coupled with acpi_put_table() if
the mapped table is not used at runtime to release the table
mapping which can prevent the memory leak.
In kfd_create_crat_image_acpi(), crat_table is copied to pcrat_image,
and in kfd_create_vcrat_image_cpu(), the acpi_table is only used to
get the OEM information, so those two table mappings need to be released
after using it.
Fixes: 174de876d6 ("drm/amdkfd: Group up CRAT related functions")
Fixes: 520b8fb755 ("drm/amdkfd: Add topology support for CPUs")
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b5c130fb2 ]
The return value of qat_hal_rd_ae_csr() is always a CSR value and never
a status and should not be stored in the status variable of
qat_hal_put_rel_rd_xfer().
This removes the assignment as qat_hal_rd_ae_csr() is not expected to
fail.
A more comprehensive handling of the theoretical corner case which could
result in a fail will be submitted in a separate patch.
Fixes: 8c9478a400 ("crypto: qat - reduce stack size with KASAN")
Signed-off-by: Jack Xu <jack.xu@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6569e3097f ]
The extra tests in the manager actually require the manager to be
selected too. Otherwise the linker gives errors like:
ld: arch/x86/crypto/chacha_glue.o: in function `chacha_simd_stream_xor':
chacha_glue.c:(.text+0x422): undefined reference to `crypto_simd_disabled_for_test'
Fixes: 2343d1529a ("crypto: Kconfig - allow tests to be disabled when manager is disabled")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1995e5afa ]
If a rstctrl reset bit is already deasserted, we can just bail out early
not wait for rstst to clear. Otherwise we can have deassert fail for
already deasserted resets.
Fixes: c5117a78dd ("soc: ti: omap-prm: poll for reset complete during de-assert")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f66bf401e ]
Compute queues are configurable with module param, num_kcq.
amdgpu_gfx_is_high_priority_compute_queue was setting 1st 4 queues to
high priority queue leaving a null drm scheduler in
adev->gpu_sched[hw_ip]["normal_prio"].sched if num_kcq < 5.
This patch tries to fix it by alternating compute queue priority between
normal and high priority.
Fixes: 33abcb1f5a (drm/amdgpu: set compute queue priority at mqd_init)
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a5fe2fb96 ]
When BCM47XX_BCMA is enabled and BCMA_DRIVER_PCI is disabled, it results
in the following Kbuild warning:
WARNING: unmet direct dependencies detected for BCMA_DRIVER_PCI_HOSTMODE
Depends on [n]: MIPS [=y] && BCMA_DRIVER_PCI [=n] && PCI_DRIVERS_LEGACY [=y] && BCMA [=y]=y
Selected by [y]:
- BCM47XX_BCMA [=y] && BCM47XX [=y] && PCI [=y]
The reason is that BCM47XX_BCMA selects BCMA_DRIVER_PCI_HOSTMODE without
depending on or selecting BCMA_DRIVER_PCI while BCMA_DRIVER_PCI_HOSTMODE
depends on BCMA_DRIVER_PCI. This can also fail building the kernel.
Honor the kconfig dependency to remove unmet direct dependency warnings
and avoid any potential build failures.
Fixes: c1d1c5d421 ("bcm47xx: add support for bcma bus")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209879
Signed-off-by: Necip Fazil Yildiran <fazilyildiran@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 358f0ac1f2 ]
SND_INTEL_DSP_CONFIG is selected by the HDaudio, Skylake and SOF
drivers. When the HDaudio link is not selected as a option, this
Kconfig option is not touched and will default to whatever other
drivers selected. In the case e.g. where HDaudio is compiled as
built-in, the linker will complain:
ld: sound/soc/sof/sof-pci-dev.o: in function `sof_pci_probe':
sof-pci-dev.c:(.text+0x5c): undefined reference to
`snd_intel_dsp_driver_probe'
Adding the select for all HDaudio platforms, regardless of whether
they rely on the HDaudio link or not, solves the problem.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Fixes: 82d9d54a6c ('ALSA: hda: add Intel DSP configuration / probe code')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20201112164425.25603-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fbb7dc5db6 ]
gcc points out a suspicious mixing of enum types in a function that
converts from MTHCA_OPCODE_* values to IB_WC_* values:
drivers/infiniband/hw/mthca/mthca_cq.c: In function 'mthca_poll_one':
drivers/infiniband/hw/mthca/mthca_cq.c:607:21: warning: implicit conversion from 'enum <anonymous>' to 'enum ib_wc_opcode' [-Wenum-conversion]
607 | entry->opcode = MTHCA_OPCODE_INVALID;
Nothing seems to ever check for MTHCA_OPCODE_INVALID again, no idea if
this is meaningful, but it seems harmless as it deals with an invalid
input.
Remove MTHCA_OPCODE_INVALID and set the ib_wc_opcode to 0xFF, which is
still bogus, but at least doesn't make compiler warnings.
Fixes: 2a4443a699 ("[PATCH] IB/mthca: fill in opcode field for send completions")
Link: https://lore.kernel.org/r/20201026211311.3887003-1-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66ab33bf6d ]
This can be triggered for example by adding the "-omand" mount option,
which will be rejected and virtio_fs_fill_super() will return an error.
In such a case the allocations for fuse_conn and fuse_mount will leak due
to s_root not yet being set and so ->put_super() not being called.
Fixes: a62a8ef9d9 ("virtio-fs: add virtiofs filesystem")
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58cfa49c2b ]
In comment 173ca26e9b ("samples/bpf: add comprehensive ipip, ipip6,
ip6ip6 test") we added ip6ip6 test for bpf tunnel testing. But in commit
933a741e3b ("selftests/bpf: bpf tunnel test.") when we moved it to
the current folder, we didn't add it.
This patch add the ip6ip6 test back to bpf tunnel test. Update the ipip6's
topology for both IPv4 and IPv6 testing. Since iperf test is removed as
currect framework simplified it in purpose, I also removed unused tcp
checkings in test_tunnel_kern.c.
Fixes: 933a741e3b ("selftests/bpf: bpf tunnel test.")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20201110015013.1570716-2-liuhangbin@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8c765811b ]
For sinks that do not support audio, there is no need to notify
audio subsystem of the connection event.
This will make sure that audio routes only to the primary display
when connected to such sinks.
changes in v2:
- Added fixes tag
- Removed nested if condition and removed usage of global pointer
Fixes: d13e36d7d2 ("drm/msm/dp: add audio support for Display Port on MSM")
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea530388e6 ]
Some dongle will not clear LINK_STATUS_UPDATED bit after
DPCD read which cause link training failed. This patch
just read 6 bytes of DPCD link status from sink and return
without checking LINK_STATUS_UPDATED bit.
Only 8 bits are used to represent link rate at sinker DPCD.
The really link rate is 2.7Mb times the 8 bits value.
For example, 0x0A at DPCD is equal to 2.7Gb (10 * 2.7Mb).
This patch also convert 8 bits value of DPCD to really link
rate to fix worng link rate error during phy compliance test.
Fixes: 6625e2637d ("drm/msm/dp: DisplayPort PHY compliance tests fixup")
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 19e52bcb27 ]
During suspend, dp host controller and hpd block are disabled due to
both ahb and aux clock are disabled. Therefore hpd plug/unplug interrupts
will not be generated. At dp_pm_resume(), reinitialize both dp host
controller and hpd block so that hpd plug/unplug interrupts will be
generated and handled by driver so that hpd connection state is updated
correctly. This patch will fix link training flaky issues.
Changes in v2:
-- use container_of to cast correct dp_display_private pointer
at both dp_pm_suspend() and dp_pm_resume().
Changes in v3:
-- replace hpd_state atomic_t with u32
Changes in v4
-- call dp_display_host_deinit() at dp_pm_suspend()
-- call dp_display_host_init() at msm_dp_display_enable()
-- fix phy->init_count unbalance which causes link training failed
Changes in v5
-- add Fixes tag
Fixes: 8ede2ecc3e (drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets)
Tested-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9294996f0b ]
The way that bpmp_populate_debugfs_inband() uses strncpy()
and strncat() makes no sense since the size argument for
the first is insufficient to contain the trailing '/'
and the second passes the length of the input rather than
the output, which triggers a warning:
In function 'strncat',
inlined from 'bpmp_populate_debugfs_inband' at ../drivers/firmware/tegra/bpmp-debugfs.c:422:4:
include/linux/string.h:289:30: warning: '__builtin_strncat' specified bound depends on the length of the source argument [-Wstringop-overflow=]
289 | #define __underlying_strncat __builtin_strncat
| ^
include/linux/string.h:367:10: note: in expansion of macro '__underlying_strncat'
367 | return __underlying_strncat(p, q, count);
| ^~~~~~~~~~~~~~~~~~~~
drivers/firmware/tegra/bpmp-debugfs.c: In function 'bpmp_populate_debugfs_inband':
include/linux/string.h:288:29: note: length computed here
288 | #define __underlying_strlen __builtin_strlen
| ^
include/linux/string.h:321:10: note: in expansion of macro '__underlying_strlen'
321 | return __underlying_strlen(p);
Simplify this to use an snprintf() instead.
Fixes: 5e37b9c137 ("firmware: tegra: Add support for in-band debug")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5771de5d5b ]
Similar to the previous patch, clear shadow on suspend to avoid timeouts
waiting for ringbuffer space.
Fixes: 8907afb476 ("drm/msm: Allow a5xx to mark the RPTR shadow as privileged")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8b0b994c3 ]
Clear the shadow rptr on suspend. Otherwise, when we resume, we can
have a stale value until CP_WHERE_AM_I executes. If we suspend near
the ringbuffer wraparound point, this can lead to a chicken/egg
situation where we are waiting for ringbuffer space to write the
CP_WHERE_AM_I (or CP_INIT) packet, because we mistakenly believe that
the ringbuffer is full (due to stale rptr value in the shadow).
Fixes errors like:
[drm:adreno_wait_ring [msm]] *ERROR* timeout waiting for space in ringbuffer 0
in the resume path.
Fixes: d3a569fccf ("drm/msm: a6xx: Use WHERE_AM_I for eligible targets")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e59dd249c ]
There are two issues in this function.
1) We can't drop the refrences on "cpu", "codec" and "platform" before
we take the reference. This doesn't cause a problem on the first
iteration because those pointers start as NULL so the of_node_put()
is a no-op. But on the subsequent iterations, it will lead to a use
after free.
2) If the devm_kzalloc() allocation failed then the code returned
directly instead of cleaning up.
Fixes: c1e6414cdc ("ASoC: qcom: common: Fix refcount imbalance on error")
Fixes: 1e36ea360a ("ASoC: qcom: common: use modern dai_link style")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20201105125154.GA176426@mwanda
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1fb17dfc25 ]
When adding device to white list the device is added to resolving list
also. It has to be added only when HCI_ENABLE_LL_PRIVACY flag is set.
HCI_ENABLE_LL_PRIVACY flag has to be tested before adding/deleting devices
to resolving list. use_ll_privacy macro is used only to check if controller
supports LL_Privacy.
https://bugzilla.kernel.org/show_bug.cgi?id=209745
Fixes: 0eee35bdfa ("Bluetooth: Update resolving list when updating whitelist")
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6dfccd13db ]
AMP_MGR is getting derefernced in hci_phy_link_complete_evt(), when called
from hci_event_packet() and there is a possibility, that hcon->amp_mgr may
not be found when accessing after initialization of hcon.
- net/bluetooth/hci_event.c:4945
The bug seems to get triggered in this line:
bredr_hcon = hcon->amp_mgr->l2cap_conn->hcon;
Fix it by adding a NULL check for the hcon->amp_mgr before checking the ev-status.
Fixes: d5e911928b ("Bluetooth: AMP: Process Physical Link Complete evt")
Reported-and-tested-by: syzbot+0bef568258653cff272f@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?extid=0bef568258653cff272f
Signed-off-by: Anmol Karn <anmol.karan123@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1e47fbca6 ]
It's not possible to reboot or poweroff Exynos7420 using PSCI. Instead
we need to use syscon reboot/poweroff drivers, like it's done for other
Exynos SoCs. This was confirmed by checking vendor source and testing it
on Samsung Galaxy S6 device based on this SoC.
To be able to use custom restart/poweroff handlers instead of PSCI
functions, we need to correct psci compatible. This also requires us to
provide function ids for CPU_ON and CPU_OFF.
Fixes: fb026cb652 ("arm64: dts: Add reboot node for exynos7")
Fixes: b9024cbc93 ("arm64: dts: Add initial device tree support for exynos7")
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Link: https://lore.kernel.org/r/20201107133926.37187-2-pawel.mikolaj.chmiel@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 73bc7510ea ]
Exynos7 uses the same syscon reboot and poweroff nodes as other Exynos
SoCs, so instead of duplicating code we can just include common dtsi
file, which already contains definitions of them. After this change,
poweroff node will be also available, previously this dts file did
contain only reboot node.
Fixes: fb026cb652 ("arm64: dts: Add reboot node for exynos7")
Fixes: b9024cbc93 ("arm64: dts: Add initial device tree support for exynos7")
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Link: https://lore.kernel.org/r/20201107133926.37187-1-pawel.mikolaj.chmiel@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 36c7c640ff ]
Assign the correct hw_op ath11k_init_wmi_config_ipq8074 to
the hw IPQ8074. Also update the correct TWT radio count.
Incorrect TWT radio count cause TWT feature fails on radio2
because physical device count is hardcoded to 2. so set
the value dynamically.
Found this during code review.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Fixes: 2d4bcbed5b ("ath11k: initialize wmi config based on hw_params")
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604512020-25197-1-git-send-email-periyasa@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6189be7d14 ]
The ath11k code will try to insert wheather rader related limits when the
DFS region is set to ETSI. For this reason, it will add two more entries in
the array of reg_rules. But the 2.4.0.1 firmware is prefiltering the list
of reg rules it returns for 2.4GHz PHYs. They will then not contain the
list of 5GHz rules and thus no wheather radar band rules were inserted by
this code.
But the code didn't fix the n_reg_rules for this regulatory domain and PHY
when this happened. This resulted in a rejection by is_valid_rd because it
found rules which start and end at 0khz. This resulted in a splat like:
Invalid regulatory domain detected
------------[ cut here ]------------
WARNING: at backports-20200628-4.4.60-9a94b73e75/net/wireless/reg.c:3721
[...]
ath11k c000000.wifi1: failed to perform regd update : -22
The number of rules must therefore be saved after they were converted from
the ath11k format to the ieee80211_regdomain format and not before.
Tested with IPQ8074 WLAN.HK.2.4.0.1.r1-00019-QCAHKSWPL_SILICONZ-1
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201030101940.2387952-1-sven@narfation.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 383a32cde4 ]
The function ath11k_wmi_send_init_country_cmd is taking 3 byte from alpha2
of the structure wmi_init_country_params. But the function
ath11k_reg_notifier is only initializing 2 bytes. The third byte is
therefore always an uninitialized value.
The command can happen to look like
0c 00 87 02 01 00 00 00 00 00 00 00 43 41 f8 00
instead of
0c 00 87 02 01 00 00 00 00 00 00 00 43 41 00 00
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.1.0.1-01161-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.4.0.1.r1-00019-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.4.0.1.r1-00026-QCAHKSWPL_SILICONZ-2
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201021140555.4114715-1-sven@narfation.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 991fcb77f4 ]
Noticed this when trying to compile with -Wall on a kernel fork. We
potentially don't set width here, which causes the compiler to complain
about width potentially being uninitialized in drm_cvt_modes(). So, let's
fix that.
Changes since v1:
* Don't emit an error as this code isn't reachable, just mark it as such
Changes since v2:
* Remove now unused variable
Fixes: 3f649ab728 ("treewide: Remove uninitialized_var() usage")
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Ilia Mirkin <imirkin@alum.mit.edu>
Link: https://patchwork.freedesktop.org/patch/msgid/20201105235703.1328115-1-lyude@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 200ea5a229 ]
A previous fix, commit 83370b31a9 ("selinux: fix error initialization
in inode_doinit_with_dentry()"), changed how failures were handled
before a SELinux policy was loaded. Unfortunately that patch was
potentially problematic for two reasons: it set the isec->initialized
state without holding a lock, and it didn't set the inode's SELinux
label to the "default" for the particular filesystem. The later can
be a problem if/when a later attempt to revalidate the inode fails
and SELinux reverts to the existing inode label.
This patch should restore the default inode labeling that existed
before the original fix, without affecting the LABEL_INVALID marking
such that revalidation will still be attempted in the future.
Fixes: 83370b31a9 ("selinux: fix error initialization in inode_doinit_with_dentry()")
Reported-by: Sven Schnelle <svens@linux.ibm.com>
Tested-by: Sven Schnelle <svens@linux.ibm.com>
Reviewed-by: Ondrej Mosnacek <omosnace@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab95bd2aa9 ]
At the time xts fallback tfm allocation fails the device struct
hasn't been enabled yet in the caam xts tfm's private context.
Fix this by using the device struct from xts algorithm's private context
or, when not available, by replacing dev_err with pr_err.
Fixes: 9d9b14dbe0 ("crypto: caam/jr - add fallback for XTS with more than 8B IV")
Fixes: 83e8aa9121 ("crypto: caam/qi - add fallback for XTS with more than 8B IV")
Fixes: 36e2d7cfdc ("crypto: caam/qi2 - add fallback for XTS with more than 8B IV")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a2715fbdc6 ]
Loading the module deadlocks since:
-local cbc(aes) implementation needs a fallback and
-crypto API tries to find one but the request_module() resolves back to
the same module
Fix this by changing the module alias for cbc(aes) and
using the NEED_FALLBACK flag when requesting for a fallback algorithm.
Fixes: 00b99ad2ba ("crypto: arm/aes-neonbs - Use generic cbc encryption path")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 519a0d7e49 ]
PAC pointer authentication signs the return address against the value
of the stack pointer, to prevent stack overrun exploits from corrupting
the control flow. However, this requires that the AUTIASP is issued with
SP holding the same value as it held when the PAC value was generated.
The Poly1305 NEON code got this wrong, resulting in crashes on PAC
capable hardware.
Fixes: f569ca1647 ("crypto: arm64/poly1305 - incorporate OpenSSL/CRYPTOGAMS ...")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4c22b80f61 ]
soc-pcm's dpcm_fe_dai_do_trigger() supported DRAIN commnad up to kernel
v5.4 where explicit switch(cmd) has been introduced which takes into
account all SNDRV_PCM_TRIGGER_xxx but SNDRV_PCM_TRIGGER_DRAIN. Update
switch statement to reactive support for it.
As DRAIN is somewhat unique by lacking negative/stop counterpart, bring
behaviour of dpcm_fe_dai_do_trigger() for said command back to its
pre-v5.4 state by adding it to START/RESUME/PAUSE_RELEASE group.
Fixes: acbf27746e ("ASoC: pcm: update FE/BE trigger order based on the command")
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20201026100129.8216-1-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 077054215a ]
The use of compat_alloc_user_space() can be easily replaced by handling
compat arguments in the regular handler, and this will make it work for
big-endian kernels as well, which at the moment get an invalid indirect
pointer argument.
Calling aac_ioctl() instead of aac_compat_do_ioctl() means the compat and
native code paths behave the same way again, which they stopped when the
adapter health check was added only in the native function.
Link: https://lore.kernel.org/r/20201030164450.1253641-1-arnd@kernel.org
Fixes: 572ee53a9b ("scsi: aacraid: check adapter health")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cccdeda362 ]
c33b7c0389 ("drm/msm/dpu: add support for clk and bw scaling for
display") has added support for handling bandwidth voting in kms path in
addition to old mdss path. However this broke all other platforms since
_dpu_core_perf_crtc_update_bus() will now error out instead of properly
calculating bandwidth and core clocks. Fix
_dpu_core_perf_crtc_update_bus() to just skip bandwidth setting instead
of returning an error in case kms->num_paths == 0 (MDSS is used for
bandwidth management).
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: c33b7c0389 ("drm/msm/dpu: add support for clk and bw scaling for display")
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a4ccc37693 ]
PHY disable/enable resets PLL registers to default values. Thus in
addition to restoring several registers we also need to restore VCO rate
settings.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: c6659785df ("drm/msm/dsi/pll: call vco set rate explicitly")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5047ab95bb ]
PHY disable/enable resets PLL registers to default values. Thus in
addition to restoring several registers we also need to restore VCO rate
settings.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: 1ef7c99d14 ("drm/msm/dsi: add support for 7nm DSI PHY/PLL")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6625e2637d ]
Bandwidth code was being used as test link rate. Fix this by converting
bandwidth code to test link rate
Do not reset voltage and pre-emphasis level during IRQ HPD attention
interrupt. Also fix pre-emphasis parsing during test link status process
Signed-off-by: Tanmay Shah <tanmay@codeaurora.org>
Fixes: 8ede2ecc3e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets")
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc3325701a ]
reg_pages should always contain mr->npage since when the mr is finally
de-reg'd it is always subtracted out.
If there were any error exits then mlx5_ib_rereg_user_mr() would leave the
reg_pages adjusted and this will cause it to be double subtracted
eventually.
The manipulation of reg_pages is inherently connected to the umem, so lift
it out of set_mr_fields() and only adjust it around creating/destroying a
umem.
reg_pages is only used for diagnostics in sysfs.
Fixes: 7d0cc6edcc ("IB/mlx5: Add MR cache for large UMR regions")
Link: https://lore.kernel.org/r/20201026131936.1335664-3-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3acc4522d8 ]
When running fault injection test, if we don't stop checkpoint, some stale
NAT entries were flushed which breaks consistency.
Fixes: 86f33603f8 ("f2fs: handle errors of f2fs_get_meta_page_nofail")
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c0b976bf2 ]
Currently in generic_secondary_smp_init(), cur_cpu_spec->cpu_restore()
is called before a stack has been set up in r1. This was previously fine
as the cpu_restore() functions were implemented in assembly and did not
use a stack. However commit 5a61ef74f2 ("powerpc/64s: Support new
device tree binding for discovering CPU features") used
__restore_cpu_cpufeatures() as the cpu_restore() function for a
device-tree features based cputable entry. This is a C function and
hence uses a stack in r1.
generic_secondary_smp_init() is entered on the secondary cpus via the
primary cpu using the OPAL call opal_start_cpu(). In OPAL, each hardware
thread has its own stack. The OPAL call is ran in the primary's hardware
thread. During the call, a job is scheduled on a secondary cpu that will
start executing at the address of generic_secondary_smp_init(). Hence
the value that will be left in r1 when the secondary cpu enters the
kernel is part of that secondary cpu's individual OPAL stack. This means
that __restore_cpu_cpufeatures() will write to that OPAL stack. This is
not horribly bad as each hardware thread has its own stack and the call
that enters the kernel from OPAL never returns, but it is still wrong
and should be corrected.
Create the temp kernel stack before calling cpu_restore().
As noted by mpe, for a kexec boot, the secondary CPUs are released from
the spin loop at address 0x60 by smp_release_cpus() and then jump to
generic_secondary_smp_init(). The call to smp_release_cpus() is in
setup_arch(), and it comes before the call to emergency_stack_init().
emergency_stack_init() allocates an emergency stack in the PACA for each
CPU. This address in the PACA is what is used to set up the temp kernel
stack in generic_secondary_smp_init(). Move releasing the secondary CPUs
to after the PACAs have been allocated an emergency stack, otherwise the
PACA stack pointer will contain garbage and hence the temp kernel stack
created from it will be broken.
Fixes: 5a61ef74f2 ("powerpc/64s: Support new device tree binding for discovering CPU features")
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201014072837.24539-1-jniethe5@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dbb60031dd ]
gcc -Wextra warns about a function taking an enum argument
being called with a bool:
drivers/gpu/drm/amd/amdgpu/../display/modules/color/color_gamma.c: In function 'apply_degamma_for_user_regamma':
drivers/gpu/drm/amd/amdgpu/../display/modules/color/color_gamma.c:1617:29: warning: implicit conversion from 'enum <anonymous>' to 'enum dc_transfer_func_predefined' [-Wenum-conversion]
1617 | build_coefficients(&coeff, true);
It appears that a patch was added using the old calling conventions
after the type was changed, and the value should actually be 0
(TRANSFER_FUNCTION_SRGB) here instead of 1 (true).
Fixes: 55a01d4023 ("drm/amd/display: Add user_regamma to color module")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 93c0210671 ]
Left and Right justified mode are computed using the same formula
as DSP_A and DSP_B mode.
Which is wrong and the user manual explicitly says:
LRCK_PERDIOD:
PCM Mode: Number of BCLKs within (Left + Right) channel width.
I2S/Left-Justified/Right-Justified Mode: Number of BCLKs within each
individual channel width(Left or Right)
Fix this by using the same formula as the I2S mode.
Fixes: 7ae7834ec4 ("ASoC: sun4i-i2s: Add support for DSP formats")
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20201030144648.397824-2-peron.clem@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c98e233062 ]
An incorrect sizeof() is being used, sizeof(priv->ring[i].rdr_req) is
not correct, it should be sizeof(*priv->ring[i].rdr_req). Note that
since the size of ** is the same size as * this is not causing any
issues.
Addresses-Coverity: ("Sizeof not portable (SIZEOF_MISMATCH)")
Fixes: 9744fec95f ("crypto: inside-secure - remove request list to improve performance")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0237616173 ]
current_desc_hdr() returns a u32 but in fact this is a __be32,
leading to a lot of sparse warnings.
Change the return type to __be32 and ensure it is handled as
sure by the caller.
Fixes: 3e721aeb3d ("crypto: talitos - handle descriptor not found in error path")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 195404db27 ]
current_desc_hdr() compares the value of the current descriptor
with the next_desc member of the talitos_desc struct.
While the current descriptor is obtained from in_be32() which
return CPU ordered bytes, next_desc member is in big endian order.
Convert the current descriptor into big endian before comparing it
with next_desc.
This fixes a sparse warning.
Fixes: 37b5e8897e ("crypto: talitos - chain in buffered data for ahash on SEC1")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a110f3750b ]
core_link_write_dpcd() returns enum dc_status, not ddc_result:
display/dc/core/dc_link_dp.c: In function 'dp_set_panel_mode':
display/dc/core/dc_link_dp.c:4237:11: warning: implicit conversion from 'enum dc_status' to 'enum ddc_result'
[-Wenum-conversion]
Avoid the warning by using the correct enum in the caller.
Fixes: 0b22632243 ("drm/amd/display: Synchronous DisplayPort Link Training")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 345a957fcc ]
do_sched_yield() invokes schedule() with interrupts disabled which is
not allowed. This goes back to the pre git era to commit a6efb709806c
("[PATCH] irqlock patch 2.5.27-H6") in the history tree.
Reenable interrupts and remove the misleading comment which "explains" it.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/87r1pt7y5c.fsf@nanos.tec.linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a57415f5d1 ]
When change sched_rt_{runtime, period}_us, we validate that the new
settings should at least accommodate the currently allocated -dl
bandwidth:
sched_rt_handler()
--> sched_dl_bandwidth_validate()
{
new_bw = global_rt_runtime()/global_rt_period();
for_each_possible_cpu(cpu) {
dl_b = dl_bw_of(cpu);
if (new_bw < dl_b->total_bw) <-------
ret = -EBUSY;
}
}
But under CONFIG_SMP, dl_bw is per root domain , but not per CPU,
dl_b->total_bw is the allocated bandwidth of the whole root domain.
Instead, we should compare dl_b->total_bw against "cpus*new_bw",
where 'cpus' is the number of CPUs of the root domain.
Also, below annotation(in kernel/sched/sched.h) implied implementation
only appeared in SCHED_DEADLINE v2[1], then deadline scheduler kept
evolving till got merged(v9), but the annotation remains unchanged,
meaningless and misleading, update it.
* With respect to SMP, the bandwidth is given on a per-CPU basis,
* meaning that:
* - dl_bw (< 100%) is the bandwidth of the system (group) on each CPU;
* - dl_total_bw array contains, in the i-eth element, the currently
* allocated bandwidth on the i-eth CPU.
[1]: https://lore.kernel.org/lkml/1267385230.13676.101.camel@Palantir/
Fixes: 332ac17ef5 ("sched/deadline: Add bandwidth management for SCHED_DEADLINE tasks")
Signed-off-by: Peng Liu <iwtbavbm@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Daniel Bristot de Oliveira <bristot@redhat.com>
Acked-by: Juri Lelli <juri.lelli@redhat.com>
Link: https://lkml.kernel.org/r/db6bbda316048cda7a1bbc9571defde193a8d67e.1602171061.git.iwtbavbm@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26573a9774 ]
Currently, Linux as a hypervisor guest will enable x2apic only if there are
no CPUs present at boot time with an APIC ID above 255.
Hotplugging a CPU later with a higher APIC ID would result in a CPU which
cannot be targeted by external interrupts.
Add a filter in x2apic_apic_id_valid() which can be used to prevent such
CPUs from coming online, and allow x2apic to be enabled even if they are
present at boot time.
Fixes: ce69a78450 ("x86/apic: Enable x2APIC without interrupt remapping under KVM")
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20201024213535.443185-2-dwmw2@infradead.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d715ff8acb ]
The purpose of srv_mutex is to protect srv_list as in put_srv, so no need
to hold it when allocate memory for srv since it could be time consuming.
Otherwise if one machine has limited memory, rsrv_close_work could be
blocked for a longer time due to the mutex is held by get_or_create_srv
since it can't get memory in time.
INFO: task kworker/1:1:27478 blocked for more than 120 seconds.
Tainted: G O 4.14.171-1-storage #4.14.171-1.3~deb9
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
kworker/1:1 D 0 27478 2 0x80000000
Workqueue: rtrs_server_wq rtrs_srv_close_work [rtrs_server]
Call Trace:
? __schedule+0x38c/0x7e0
schedule+0x32/0x80
schedule_preempt_disabled+0xa/0x10
__mutex_lock.isra.2+0x25e/0x4d0
? put_srv+0x44/0x100 [rtrs_server]
put_srv+0x44/0x100 [rtrs_server]
rtrs_srv_close_work+0x16c/0x280 [rtrs_server]
process_one_work+0x1c5/0x3c0
worker_thread+0x47/0x3e0
kthread+0xfc/0x130
? trace_event_raw_event_workqueue_execute_start+0xa0/0xa0
? kthread_create_on_node+0x70/0x70
ret_from_fork+0x1f/0x30
Let's move all the logics from __find_srv_and_get and __alloc_srv to
get_or_create_srv, and remove the two functions. Then it should be safe
for multiple processes to access the same srv since it is protected with
srv_mutex.
And since we don't want to allocate chunks with srv_mutex held, let's
check the srv->refcount after get srv because the chunks could not be
allocated yet.
Fixes: 9cb8374804 ("RDMA/rtrs: server: main functionality")
Link: https://lore.kernel.org/r/20201023074353.21946-6-jinpu.wang@cloud.ionos.com
Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e79f0211b ]
When running in BE mode on LPAE hardware with a PA-to-VA translation
that exceeds 4 GB, we patch bits 39:32 of the offset into the wrong
byte of the opcode. So fix that, by rotating the offset in r0 to the
right by 8 bits, which will put the 8-bit immediate in bits 31:24.
Note that this will also move bit #22 in its correct place when
applying the rotation to the constant #0x400000.
Fixes: d9a790df8e ("ARM: 7883/1: fix mov to mvn conversion in case of 64 bit phys_addr_t and BE")
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1fcd009102 ]
Commit
ea3b5e60ce ("x86/mm/ident_map: Add 5-level paging support")
added ident_p4d_init() to support 5-level paging, but this function
doesn't check and return errors from ident_pud_init().
For example, the decompressor stub uses this code to create an identity
mapping. If it runs out of pages while trying to allocate a PMD
pagetable, the error will be currently ignored.
Fix this to propagate errors.
[ bp: Space out statements for better readability. ]
Fixes: ea3b5e60ce ("x86/mm/ident_map: Add 5-level paging support")
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Link: https://lkml.kernel.org/r/20201027230648.1885111-1-nivedita@alum.mit.edu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb3ab2979f ]
The code which limited the number of unacknowledged PSNs was incorrect.
The PSNs are limited to 24 bits and wrap back to zero from 0x00ffffff.
The test was computing a 32 bit value which wraps at 32 bits so that
qp->req.psn can appear smaller than the limit when it is actually larger.
Replace '>' test with psn_compare which is used for other PSN comparisons
and correctly handles the 24 bit size.
Fixes: 8700e3e7c4 ("Soft RoCE driver")
Link: https://lore.kernel.org/r/20201013170741.3590-1-rpearson@hpe.com
Signed-off-by: Bob Pearson <rpearson@hpe.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e1cc96797 ]
The VGA memory region is always from the top of RAM. On this board, that
is 0x80000000 + 0x20000000 - 0x01000000 = 0x9f000000.
This was not an issue in practice as the region is "reserved" by the
vendor's u-boot reducing the amount of available RAM, and the only user
is the host VGA device poking at RAM over PCIe. That is, nothing from
the ARM touches it.
It is worth fixing as developers copy existing device trees when
building their machines, and the XDMA driver does use the memory region
from the ARM side.
Fixes: c4043ecac3 ("ARM: dts: aspeed: Add S2600WF BMC Machine")
Reported-by: John Wang <wangzhiqiang.bj@bytedance.com>
Link: https://lore.kernel.org/r/20200922064234.163799-1-joel@jms.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 83370b31a9 ]
Mark the inode security label as invalid if we cannot find
a dentry so that we will retry later rather than marking it
initialized with the unlabeled SID.
Fixes: 9287aed2ad ("selinux: Convert isec->lock into a spinlock")
Signed-off-by: Tianyue Ren <rentianyue@kylinos.cn>
[PM: minor comment tweaks]
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9cb4c67d77 ]
This reverts commit 02b9aec592.
As talked about in the patch ("soc: qcom: geni: More properly switch
to DMA mode"), swapping the order of geni_se_setup_m_cmd() and
geni_se_xx_dma_prep() can sometimes cause corrupted transfers. Thus
we traded one problem for another. Now that we've debugged the
problem further and fixed the geni helper functions to more disable
FIFO interrupts when we move to DMA mode we can revert it and end up
with (hopefully) zero problems!
To be explicit, the patch ("soc: qcom: geni: More properly switch
to DMA mode") is a prerequisite for this one.
Fixes: 02b9aec592 ("i2c: i2c-qcom-geni: Fix DMA transfer race")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20201013142448.v2.2.I7b22281453b8a18ab16ef2bfd4c641fb1cc6a92c@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b6ea87be4 ]
On geni-i2c transfers using DMA, it was seen that if you program the
command (I2C_READ) before calling geni_se_rx_dma_prep() that it could
cause interrupts to fire. If we get unlucky, these interrupts can
just keep firing (and not be handled) blocking further progress and
hanging the system.
In commit 02b9aec592 ("i2c: i2c-qcom-geni: Fix DMA transfer race")
we avoided that by making sure we didn't program the command until
after geni_se_rx_dma_prep() was called. While that avoided the
problems, it also turns out to be invalid. At least in the TX case we
started seeing sporadic corrupted transfers. This is easily seen by
adding an msleep() between the DMA prep and the writing of the
command, which makes the problem worse. That means we need to revert
that commit and find another way to fix the bogus IRQs.
Specifically, after reverting commit 02b9aec592 ("i2c:
i2c-qcom-geni: Fix DMA transfer race"), I put some traces in. I found
that the when the interrupts were firing like crazy:
- "m_stat" had bits for M_RX_IRQ_EN, M_RX_FIFO_WATERMARK_EN set.
- "dma" was set.
Further debugging showed that I could make the problem happen more
reliably by adding an "msleep(1)" any time after geni_se_setup_m_cmd()
ran up until geni_se_rx_dma_prep() programmed the length.
A rather simple fix is to change geni_se_select_dma_mode() so it's a
true inverse of geni_se_select_fifo_mode() and disables all the FIFO
related interrupts. Now the problematic interrupts can't fire and we
can program things in the correct order without worrying.
As part of this, let's also change the writel_relaxed() in the prepare
function to a writel() so that our DMA is guaranteed to be prepared
now that we can't rely on geni_se_setup_m_cmd()'s writel().
NOTE: the only current user of GENI_SE_DMA in mainline is i2c.
Fixes: 37692de5d5 ("i2c: i2c-qcom-geni: Add bus driver for the Qualcomm GENI I2C controller")
Fixes: 02b9aec592 ("i2c: i2c-qcom-geni: Fix DMA transfer race")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20201013142448.v2.1.Ifdb1b69fa3367b81118e16e9e4e63299980ca798@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 228813aaa7 ]
In commit e23b1220a2 ("arm64: dts: qcom: sc7180: Increase the number
of interconnect cells") we missed increasing the cells on one
interconnect. That's no bueno. Fix it.
NOTE: it appears that things aren't totally broken without this fix,
but clearly something isn't going to be working right. If nothing
else, without this fix I see this in the logs:
OF: /soc@0/mdss@ae00000: could not get #interconnect-cells for /soc@0/interrupt-controller@17a00000
Fixes: e23b1220a2 ("arm64: dts: qcom: sc7180: Increase the number of interconnect cells")
Reviewed-by: Georgi Djakov <georgi.djakov@linaro.org>
Reviewed-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20201001141838.1.I08054d1d976eed64ffa1b0e21d568e0dc6040b54@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4007844b05 ]
In the error case, where a power domain cannot be powered on
successfully at boot time (in mtk_register_power_domains),
pm_genpd_init would still be called with is_off=false, and the
system would later try to disable the power domain again, triggering
warnings as disabled clocks are disabled again (and other potential
issues).
Also print a warning splat in that case, as this should never
happen.
Fixes: c84e358718 ("soc: Mediatek: Add SCPSYS power domain driver")
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Link: https://lore.kernel.org/r/20200928113107.v2.1.I5e6f8c262031d0451fe7241b744f4f3111c1ce71@changeid
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f091d7c5fe ]
This tries to solve a warning reported by the lkp bot:
>> drivers/iio/adc/at91_adc.c:1439:34: warning: unused variable
>> 'at91_adc_dt_ids' [-Wunused-const-variable]
static const struct of_device_id at91_adc_dt_ids[] = {
^
1 warning generated.
This warning has appeared after the AT91_ADC driver compilation has been
enabled via the COMPILE_TEST symbol dependency.
The warning is caused by the 'of_match_ptr()' helper which returns NULL if
OF is undefined. This driver should build only for device-tree context, so
a dependency on the OF Kconfig symbol has been added.
Also, the usage of of_match_ptr() helper has been removed since it
shouldn't ever return NULL (because the driver should not be built for the
non-OF context).
Fixes: 4027860dcc ("iio: Kconfig: at91_adc: add COMPILE_TEST dependency to driver")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200930135048.11530-4-alexandru.ardelean@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e19d51ca5 ]
clang static analysis reports this problem:
cdv_intel_dp.c:2101:2: warning: Attempt to free released memory
kfree(gma_connector);
^~~~~~~~~~~~~~~~~~~~
In cdv_intel_dp_init() when the call to cdv_intel_edp_panel_vdd_off()
fails, the handler calls cdv_intel_dp_destroy(connector) which does
the first free of gma_connector. So adjust the goto label and skip
the second free.
Fixes: d112a8163f ("gma500/cdv: Add eDP support")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20201003193928.18869-1-trix@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0a4e668b5d upstream.
Voltages and current are reported by Zen CPUs. However, the means
to do so is undocumented, changes from CPU to CPU, and the raw data
is not calibrated. Calibration information is available, but again
not documented. This results in less than perfect user experience,
up to concerns that loading the driver might possibly damage
the hardware (by reporting out-of range voltages). Effectively
support for reporting voltages and current is not maintainable.
Drop it.
Cc: Artem S. Tashkinov <aros@gmx.com>
Cc: Wei Huang <wei.huang2@amd.com>
Tested-by: Wei Huang <wei.huang2@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 92eb6c3060 upstream.
Commit 3f69cc6076 ("crypto: af_alg - Allow arbitrarily long algorithm
names") made the kernel start accepting arbitrarily long algorithm names
in sockaddr_alg. However, the actual length of the salg_name field
stayed at the original 64 bytes.
This is broken because the kernel can access indices >= 64 in salg_name,
which is undefined behavior -- even though the memory that is accessed
is still located within the sockaddr structure. It would only be
defined behavior if the array were properly marked as arbitrary-length
(either by making it a flexible array, which is the recommended way
these days, or by making it an array of length 0 or 1).
We can't simply change salg_name into a flexible array, since that would
break source compatibility with userspace programs that embed
sockaddr_alg into another struct, or (more commonly) declare a
sockaddr_alg like 'struct sockaddr_alg sa = { .salg_name = "foo" };'.
One solution would be to change salg_name into a flexible array only
when '#ifdef __KERNEL__'. However, that would keep userspace without an
easy way to actually use the longer algorithm names.
Instead, add a new structure 'sockaddr_alg_new' that has the flexible
array field, and expose it to both userspace and the kernel.
Make the kernel use it correctly in alg_bind().
This addresses the syzbot report
"UBSAN: array-index-out-of-bounds in alg_bind"
(https://syzkaller.appspot.com/bug?extid=92ead4eb8e26a26d465e).
Reported-by: syzbot+92ead4eb8e26a26d465e@syzkaller.appspotmail.com
Fixes: 3f69cc6076 ("crypto: af_alg - Allow arbitrarily long algorithm names")
Cc: <stable@vger.kernel.org> # v4.12+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bfc2b7e851 upstream.
As described in "fscrypt: add fscrypt_is_nokey_name()", it's possible to
create a duplicate filename in an encrypted directory by creating a file
concurrently with adding the directory's encryption key.
Fix this bug on f2fs by rejecting no-key dentries in f2fs_add_link().
Note that the weird check for the current task in f2fs_do_add_link()
seems to make this bug difficult to reproduce on f2fs.
Fixes: 9ea97163c6 ("f2fs crypto: add filename encryption for f2fs_add_link")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20201118075609.120337-4-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 75d18cd186 upstream.
As described in "fscrypt: add fscrypt_is_nokey_name()", it's possible to
create a duplicate filename in an encrypted directory by creating a file
concurrently with adding the directory's encryption key.
Fix this bug on ext4 by rejecting no-key dentries in ext4_add_entry().
Note that the duplicate check in ext4_find_dest_de() sometimes prevented
this bug. However in many cases it didn't, since ext4_find_dest_de()
doesn't examine every dentry.
Fixes: 4461471107 ("ext4 crypto: enable filename encryption")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20201118075609.120337-3-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 76786a0f08 upstream.
As described in "fscrypt: add fscrypt_is_nokey_name()", it's possible to
create a duplicate filename in an encrypted directory by creating a file
concurrently with adding the directory's encryption key.
Fix this bug on ubifs by rejecting no-key dentries in ubifs_create(),
ubifs_mkdir(), ubifs_mknod(), and ubifs_symlink().
Note that ubifs doesn't actually report the duplicate filenames from
readdir, but rather it seems to replace the original dentry with a new
one (which is still wrong, just a different effect from ext4).
On ubifs, this fixes xfstest generic/595 as well as the new xfstest I
wrote specifically for this bug.
Fixes: f4f61d2cc6 ("ubifs: Implement encrypted filenames")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20201118075609.120337-5-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 159e1de201 upstream.
It's possible to create a duplicate filename in an encrypted directory
by creating a file concurrently with adding the encryption key.
Specifically, sys_open(O_CREAT) (or sys_mkdir(), sys_mknod(), or
sys_symlink()) can lookup the target filename while the directory's
encryption key hasn't been added yet, resulting in a negative no-key
dentry. The VFS then calls ->create() (or ->mkdir(), ->mknod(), or
->symlink()) because the dentry is negative. Normally, ->create() would
return -ENOKEY due to the directory's key being unavailable. However,
if the key was added between the dentry lookup and ->create(), then the
filesystem will go ahead and try to create the file.
If the target filename happens to already exist as a normal name (not a
no-key name), a duplicate filename may be added to the directory.
In order to fix this, we need to fix the filesystems to prevent
->create(), ->mkdir(), ->mknod(), and ->symlink() on no-key names.
(->rename() and ->link() need it too, but those are already handled
correctly by fscrypt_prepare_rename() and fscrypt_prepare_link().)
In preparation for this, add a helper function fscrypt_is_nokey_name()
that filesystems can use to do this check. Use this helper function for
the existing checks that fs/crypto/ does for rename and link.
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20201118075609.120337-2-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ceb6543e9 upstream.
There isn't really any valid reason to use __FSCRYPT_MODE_MAX or
FSCRYPT_POLICY_FLAGS_VALID in a userspace program. These constants are
only meant to be used by the kernel internally, and they are defined in
the UAPI header next to the mode numbers and flags only so that kernel
developers don't forget to update them when adding new modes or flags.
In https://lkml.kernel.org/r/20201005074133.1958633-2-satyat@google.com
there was an example of someone wanting to use __FSCRYPT_MODE_MAX in a
user program, and it was wrong because the program would have broken if
__FSCRYPT_MODE_MAX were ever increased. So having this definition
available is harmful. FSCRYPT_POLICY_FLAGS_VALID has the same problem.
So, remove these definitions from the UAPI header. Replace
FSCRYPT_POLICY_FLAGS_VALID with just listing the valid flags explicitly
in the one kernel function that needs it. Move __FSCRYPT_MODE_MAX to
fscrypt_private.h, remove the double underscores (which were only
present to discourage use by userspace), and add a BUILD_BUG_ON() and
comments to (hopefully) ensure it is kept in sync.
Keep the old name FS_POLICY_FLAGS_VALID, since it's been around for
longer and there's a greater chance that removing it would break source
compatibility with some program. Indeed, mtd-utils is using it in
an #ifdef, and removing it would introduce compiler warnings (about
FS_POLICY_FLAGS_PAD_* being redefined) into the mtd-utils build.
However, reduce its value to 0x07 so that it only includes the flags
with old names (the ones present before Linux 5.4), and try to make it
clear that it's now "frozen" and no new flags should be added to it.
Fixes: 2336d0deb2 ("fscrypt: use FSCRYPT_ prefix for uapi constants")
Cc: <stable@vger.kernel.org> # v5.4+
Link: https://lore.kernel.org/r/20201024005132.495952-1-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f70e49ed8 upstream.
At the moment opening a serial device node (such as /dev/ttyS3)
succeeds even if there is no actual serial device behind it.
Reading/writing/ioctls fail as expected because the uart port is not
initialized (the type is PORT_UNKNOWN) and the TTY_IO_ERROR error state
bit is set fot the tty.
However setting line discipline does not have these checks
8250_port.c (8250 is the default choice made by univ8250_console_init()).
As the result of PORT_UNKNOWN, uart_port::iobase is NULL which
a platform translates onto some address accessing which produces a crash
like below.
This adds tty_port_initialized() to uart_set_ldisc() to prevent the crash.
Found by syzkaller.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Link: https://lore.kernel.org/r/20201203055834.45838-1-aik@ozlabs.ru
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 381d34e376 upstream.
It sounds unwise to let user space pass an unchecked 32-bit offset into a
kernel structure in an ioctl. This is an unsigned variable, so checking the
upper bound for the size of the structure it points into is sufficient to
avoid data corruption, but as the pointer might also be unaligned, it has
to be written carefully as well.
While I stumbled over this problem by reading the code, I did not continue
checking the function for further problems like it.
Link: https://lore.kernel.org/r/20201030164450.1253641-2-arnd@kernel.org
Fixes: c4a3e0a529 ("[SCSI] MegaRAID SAS RAID: new driver")
Cc: <stable@vger.kernel.org> # v2.6.15+
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 22b2beaa7f upstream.
There was a report of NULL pointer dereference in ETF enable
path for perf CS mode with PID monitoring. It is almost 100%
reproducible when the process to monitor is something very
active such as chrome and with ETF as the sink, not ETR.
But code path shows that ETB has a similar path as ETF, so
there could be possible NULL pointer dereference crash in
ETB as well. Currently in a bid to find the pid, the owner
is dereferenced via task_pid_nr() call in etb_enable_perf()
and with owner being NULL, we can get a NULL pointer
dereference, so have a similar fix as ETF where we cache PID
in alloc_buffer() callback which is called as the part of
etm_setup_aux().
Fixes: 75d7dbd388 ("coresight: etb10: Add support for CPU-wide trace scenarios")
Cc: stable@vger.kernel.org
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20201127175256.1092685-11-mathieu.poirier@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 83be0b84fe upstream.
When the ETR is used in perf mode with a larger buffer (configured
via sysfs or the default size of 1M) than the perf aux buffer size,
we end up inserting the barrier packet at the wrong offset, while
moving the offset forward. i.e, instead of the "new moved offset",
we insert it at the current hardware buffer offset. These packets
will not be visible as they are never copied and could lead to
corruption in the trace decoding side, as the decoder is not aware
that it needs to reset the decoding.
Fixes: ec13c78d7b ("coresight: tmc-etr: Add barrier packets when moving offset forward")
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: stable@vger.kernel.org
Reported-by: Al Grant <al.grant@arm.com>
Tested-by: Mike Leach <mike.leach@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20201208182651.1597945-2-mathieu.poirier@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1cc573d575 upstream.
alloc_pages_node() return should be checked before calling
dma_map_page() to make sure that valid page is mapped or
else it can lead to aborts as below:
Unable to handle kernel paging request at virtual address ffffffc008000000
Mem abort info:
<snip>...
pc : __dma_inv_area+0x40/0x58
lr : dma_direct_map_page+0xd8/0x1c8
Call trace:
__dma_inv_area
tmc_pages_alloc
tmc_alloc_data_pages
tmc_alloc_sg_table
tmc_init_etr_sg_table
tmc_alloc_etr_buf
tmc_enable_etr_sink_sysfs
tmc_enable_etr_sink
coresight_enable_path
coresight_enable
enable_source_store
dev_attr_store
sysfs_kf_write
Fixes: 99443ea19e ("coresight: Add generic TMC sg table framework")
Cc: stable@vger.kernel.org
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mao Jinlong <jinlmao@codeaurora.org>
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20201127175256.1092685-13-mathieu.poirier@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 868663dd5d upstream.
There was a report of NULL pointer dereference in ETF enable
path for perf CS mode with PID monitoring. It is almost 100%
reproducible when the process to monitor is something very
active such as chrome and with ETF as the sink and not ETR.
Currently in a bid to find the pid, the owner is dereferenced
via task_pid_nr() call in tmc_enable_etf_sink_perf() and with
owner being NULL, we get a NULL pointer dereference.
Looking at the ETR and other places in the kernel, ETF and the
ETB are the only places trying to dereference the task(owner)
in tmc_enable_etf_sink_perf() which is also called from the
sched_in path as in the call trace. Owner(task) is NULL even
in the case of ETR in tmc_enable_etr_sink_perf(), but since we
cache the PID in alloc_buffer() callback and it is done as part
of etm_setup_aux() when allocating buffer for ETR sink, we never
dereference this NULL pointer and we are safe. So lets do the
same thing with ETF and cache the PID to which the cs_buffer
belongs in tmc_alloc_etf_buffer() as done for ETR. This will
also remove the unnecessary function calls(task_pid_nr()) since
we are caching the PID.
Easily reproducible running below:
perf record -e cs_etm/@tmc_etf0/ -N -p <pid>
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000548
Mem abort info:
ESR = 0x96000006
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
Data abort info:
ISV = 0, ISS = 0x00000006
CM = 0, WnR = 0
<snip>...
Call trace:
tmc_enable_etf_sink+0xe4/0x280
coresight_enable_path+0x168/0x1fc
etm_event_start+0x8c/0xf8
etm_event_add+0x38/0x54
event_sched_in+0x194/0x2ac
group_sched_in+0x54/0x12c
flexible_sched_in+0xd8/0x120
visit_groups_merge+0x100/0x16c
ctx_flexible_sched_in+0x50/0x74
ctx_sched_in+0xa4/0xa8
perf_event_sched_in+0x60/0x6c
perf_event_context_sched_in+0x98/0xe0
__perf_event_task_sched_in+0x5c/0xd8
finish_task_switch+0x184/0x1cc
schedule_tail+0x20/0xec
ret_from_fork+0x4/0x18
Fixes: 880af782c6 ("coresight: tmc-etf: Add support for CPU-wide trace scenarios")
Cc: stable@vger.kernel.org
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20201127175256.1092685-10-mathieu.poirier@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd7e7ff56f upstream.
On Odroid XU LDO12 and LDO15 supplies the power to USB 3.0 blocks but
the GPK GPIO pins are supplied by LDO7 (VDDQ_LCD). LDO7 also supplies
GPJ GPIO pins.
The Exynos pinctrl driver does not take any supplies, so to have entire
GPIO block always available, make the regulator always on.
Fixes: 88644b4c75 ("ARM: dts: exynos: Configure PWM, usb3503, PMIC and thermal on Odroid XU board")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201015182044.480562-3-krzk@kernel.org
Tested-by: Gabriel Ribba Esteva <gabriel.ribbae@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d992fd8f4 upstream.
The VBUS control (PWREN) and over-current pins of USB 3.0 DWC3
controllers are on Exynos5410 regular GPIOs. This is different than for
example on Exynos5422 where these are special ETC pins with proper reset
values (pulls, functions).
Therefore these pins should be configured to enable proper USB 3.0
peripheral and host modes. This also fixes over-current warning:
[ 6.024658] usb usb4-port1: over-current condition
[ 6.028271] usb usb3-port1: over-current condition
Fixes: cb08965622 ("ARM: dts: exynos: Add USB to Exynos5410")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201015182044.480562-2-krzk@kernel.org
Tested-by: Gabriel Ribba Esteva <gabriel.ribbae@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a353397b0d upstream.
In many cases a function that supports SuperSpeed can very well
operate in SuperSpeedPlus, if a gadget controller supports it,
as the endpoint descriptors (and companion descriptors) are
generally identical and can be re-used. This is true for two
commonly used functions: Android's ADB and MTP. So we can simply
assign the usb_function's ssp_descriptors array to point to its
ss_descriptors, if available. Similarly, we need to allow an
epfile's ioctl for FUNCTIONFS_ENDPOINT_DESC to correctly
return the corresponding SuperSpeed endpoint descriptor in case
the connected speed is SuperSpeedPlus as well.
The only exception is if a function wants to implement an
Isochronous endpoint capable of transferring more than 48KB per
service interval when operating at greater than USB 3.1 Gen1
speed, in which case it would require an additional SuperSpeedPlus
Isochronous Endpoint Companion descriptor to be returned as part
of the Configuration Descriptor. Support for that would need
to be separately added to the userspace-facing FunctionFS API
which may not be a trivial task--likely a new descriptor format
(v3?) may need to be devised to allow for separate SS and SSP
descriptors to be supplied.
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201027230731.9073-1-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e14fd4ba8f upstream.
When a split lock is detected always make sure to disable interrupts
before returning from the trap handler.
The kernel exit code assumes that all exits run with interrupts
disabled, otherwise the SWAPGS sequence can race against interrupts and
cause recursing page faults and later panics.
The problem will only happen on CPUs with split lock disable
functionality, so Icelake Server, Tiger Lake, Snow Ridge, Jacobsville.
Fixes: ca4c6a9858 ("x86/traps: Make interrupt enable/disable symmetric in C code")
Fixes: bce9b042ec ("x86/traps: Disable interrupts in exc_aligment_check()") # v5.8+
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c9f64d1fc1 upstream.
When dumping the name and NTP servers advertised by DHCP, a blank line
is emitted if either of the lists is empty. This can lead to confusing
issues such as the blank line getting flagged as warning. This happens
because the blank line is the result of pr_cont("\n") and that may see
its level corrupted by some other driver concurrently writing to the
console.
Fix this by making sure that the terminating newline is only emitted
if at least one entry in the lists was printed before.
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20201110073757.1284594-1-thierry.reding@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d96f04d347 upstream.
It has been observed that once per 300-1300 port openings the first
transmitted byte is being corrupted on AM3352 ("v" written to FIFO appeared
as "e" on the wire). It only happened if single byte has been transmitted
right after port open, which means, DMA is not used for this transfer and
the corruption never happened afterwards.
Therefore I've carefully re-read the MDR1 errata (link below), which says
"when accessing the MDR1 registers that causes a dummy under-run condition
that will freeze the UART in IrDA transmission. In UART mode, this may
corrupt the transferred data". Strictly speaking,
omap_8250_mdr1_errataset() performs a read access and if the value is the
same as should be written, exits without errata-recommended FIFO reset.
A brief check of the serial_omap_mdr1_errataset() from the competing
omap-serial driver showed it has no read access of MDR1. After removing the
read access from omap_8250_mdr1_errataset() the data corruption never
happened any more.
Link: https://www.ti.com/lit/er/sprz360i/sprz360i.pdf
Fixes: 61929cf016 ("tty: serial: Add 8250-core based omap driver")
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20201210055257.1053028-1-alexander.sverdlin@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 862ee699fe upstream.
The console part of sisusbvga is broken vs. printk(). It uses in_atomic()
to detect contexts in which it cannot sleep despite the big fat comment in
preempt.h which says: Do not use in_atomic() in driver code.
in_atomic() does not work on kernels with CONFIG_PREEMPT_COUNT=n which
means that spin/rw_lock held regions are not detected by it.
There is no way to make this work by handing context information through to
the driver and this only can be solved once the core printk infrastructure
supports sleepable console drivers.
Make it depend on BROKEN for now.
Fixes: 1bbb4f2035 ("[PATCH] USB: sisusb[vga] update")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20201019101109.603244207@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c6dde8ffd0 upstream.
The current channel-map control implementation in USB-audio driver may
lead to an error message like
"control 3:0:0:Playback Channel Map:0: access overflow"
when CONFIG_SND_CTL_VALIDATION is set. It's because the chmap get
callback clears the whole array no matter which count is set, and
rather the false-positive detection.
This patch fixes the problem by clearing only the needed array range
at usb_chmap_ctl_get().
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201211130048.6358-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 170f4869e6 upstream.
The logic for truncating the log file for emailing based on the
MAIL_MAX_SIZE option is confusing and incorrect. Simplify it and have the
tail of the log file truncated to the max size specified in the config.
Cc: stable@vger.kernel.org
Fixes: 855d8abd2e ("ktest.pl: Change the logic to control the size of the log file emailed")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8cd6bc0359 upstream.
If the size of the error log is too big to send via email, and the sending
fails, it wont email any result. This can be confusing for the user who is
waiting for an email on the completion of the tests.
If it fails to send email, then try again without the log file stating that
it failed to send an email. Obviously this will not be of use if the sending
of email failed for some other reasons, but it will at least give the user
some information when it fails for the most common reason.
Cc: stable@vger.kernel.org
Fixes: c2d84ddb33 ("ktest.pl: Add MAIL_COMMAND option to define how to send email")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This repository contains the Linux kernel used on the Raspberry Pi. If you believe that the issue you are seeing is kernel-related, this is the right place. If not, we have other repositories for the GPU firmware at [github.com/raspberrypi/firmware](https://github.com/raspberrypi/firmware) and Raspberry Pi userland applications at [github.com/raspberrypi/userland](https://github.com/raspberrypi/userland). If you have problems with the Raspbian distribution packages, report them in the [github.com/RPi-Distro/repo](https://github.com/RPi-Distro/repo). If you simply have a question, then [the Raspberry Pi forums](https://www.raspberrypi.org/forums) are the best place to ask it.
**Describe the bug**
Add a clear and concise description of what you think the bug is.
**To reproduce**
List the steps required to reproduce the issue.
**Expected behaviour**
Add a clear and concise description of what you expected to happen.
**Actual behaviour**
Add a clear and concise description of what actually happened.
**System**
Copy and paste the results of the raspinfo command in to this section. Alternatively, copy and paste a pastebin link, or add answers to the following questions:
* Which model of Raspberry Pi? e.g. Pi3B+, PiZeroW
* Which OS and version (`cat /etc/rpi-issue`)?
* Which firmware version (`vcgencmd version`)?
* Which kernel version (`uname -a`)?
**Logs**
If applicable, add the relevant output from `dmesg` or similar.
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
