imx708_set_framing_limits resets the vblank control to the mode default
value unconditionally. This causes it to overwrite the user specified
vblank and exposure control values when starting the sensor, since
it is called when handling V4L2_CID_WIDE_DYNAMIC_RANGE.
Remove this call to s_ctrl as it is unnecessary.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
The probe calls pm_runtime_set_active in the probe, but
has never called dw9807_vcm_resume.
Without a regulator this causes no issue as it just
instructs the VCM to move to the idle position and power
down. With a regulator the pm_runtime_idle calls
dw9807_vcm_suspend, and we get a mismatch in the regulator framework.
Make the active state conditional on having a regulator.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Add support for the Measurement Specialities temperature and pressure
sensors to the i2c-sensor overlay. The supported devices are MS5637,
MS5803, MS5805, MS5837 and MS8607.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
CM4 uses BCM54210PE, which supports 2 additional LEDs, choosing LED3
for the amber LED because it shows activity by default (LED4 is not
connected). However, this makes it uncontrollable by the eth_led<n>
dtparams which target LEDs 1+2.
Solve the problem by making LEDs 3+4 mirror LEDs 1+2 (which is much
simpler than adding baseboard-specific overrides, but comes with a
risk of making one of the LEDs redundant).
See: https://github.com/raspberrypi/linux/issues/5289
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
New overlay to support the Sony IMX708 image sensor.
This includes a VCM for lens control.
Also adds support to the camera mux overlays.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The imx708 is a 12MP MIPI sensor with a 16:9 aspect ratio, here using
two CSI-2 lanes. It is a "quad Bayer" sensor with all 3 modes offering
10-bit output:
12MP: 4608x2592 up to 14.35fps (full FoV)
1080p: 2304x1296 up to 56.02fps (full FoV)
720p: 1536x864 up to 120.12fps (cropped)
This imx708 sensor driver is based heavily on the imx477 driver and
has been tested on the Raspberry Pi platform using libcamera.
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Add YAML devicetree binding for IMX708 CMOS image sensor.
Let's also add a MAINTAINERS entry for the binding and driver.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The power up/down sequence is already ramped. Extend this to
the first user movement as well, as this will generally avoid
the "tick" noises due to rapid movements and overshooting.
Subsequent movements are generally smaller and so don't cause
issues.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Uses the regulator notifier framework so that the current
focus position will be restored whenever any user of the
regulator powers it up. This means that should the VCM
and sensor share a common regulator then starting the sensor
will automatically restore the default position. If they
have independent regulators then it will behave be powered
up when the VCM subdev is opened.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The VCM driver will often be controlled via a regulator,
therefore add in the relevant DT hooks.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The DW9817 is effectively the same as DW9807 from a programming
interface, however it drives +/-100mA instead of 0-100mA. This means
that the power on ramp needs to take the lens from the midpoint, and
power off return it there. It also changes the default position for
the module.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The DW9817 is programmatically the same as DW9807, but
the output drive is a bi-directional -100 to +100mA
instead of 0-100mA.
Add the appropriate compativle string.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The brcm,function property must be set in the overlay fragment too -
otherwise the parametrization won't work. At least that's the case for
bcm2711-rpi-cm4.dts which starts with empty properties:
&gpio {
audio_pins: audio_pins {
brcm,pins = <>;
brcm,function = <>;
};
};
This was broken since a56df85d2f.
Signed-off-by: Krzysztof Kotlenga <k.kotlenga@sims.pl>
YUV images can either be presented as one allocation with offsets
for the different planes, or multiple allocations with 0 offsets.
The driver only ever calls drm_fb_[dma|cma]_get_gem_obj with plane
index 0, therefore any application using the second approach was
incorrectly rendered.
Correctly determine the address for each plane, removing the
assumption that the base address is the same for each.
Fixes: fc04023faf ("drm/vc4: Add support for YUV planes.")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
commit 7e6303567c upstream.
Prior to the Fixes: commit, the initialization code went through the
same fec_enet_set_coalesce() function as used by ethtool, and that
function correctly checks whether the current variant has support for
irq coalescing.
Now that the initialization code instead calls fec_enet_itr_coal_set()
directly, that call needs to be guarded by a check for the
FEC_QUIRK_HAS_COALESCE bit.
Fixes: df727d4547 (net: fec: don't reset irq coalesce settings to defaults on "ip link up")
Reported-by: Greg Ungerer <gregungerer@westnet.com.au>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221205204604.869853-1-linux@rasmusvillemoes.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a56ea6147f ]
If the prp2 field is not filled in nvme_setup_prp_simple(), the prp2
field is garbage data. According to nvme spec, the prp2 is reserved if
the data transfer does not cross a memory page boundary, so clear it to
zero if it is not used.
Signed-off-by: Lei Rao <lei.rao@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 517e6a301f ]
Per syzbot it is possible for perf_pending_task() to run after the
event is free()'d. There are two related but distinct cases:
- the task_work was already queued before destroying the event;
- destroying the event itself queues the task_work.
The first cannot be solved using task_work_cancel() since
perf_release() itself might be called from a task_work (____fput),
which means the current->task_works list is already empty and
task_work_cancel() won't be able to find the perf_pending_task()
entry.
The simplest alternative is extending the perf_event lifetime to cover
the task_work.
The second is just silly, queueing a task_work while you know the
event is going away makes no sense and is easily avoided by
re-arranging how the event is marked STATE_DEAD and ensuring it goes
through STATE_OFF on the way down.
Reported-by: syzbot+9228d6098455bb209ec8@syzkaller.appspotmail.com
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Marco Elver <elver@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df727d4547 ]
Currently, when a FEC device is brought up, the irq coalesce settings
are reset to their default values (1000us, 200 frames). That's
unexpected, and breaks for example use of an appropriate .link file to
make systemd-udev apply the desired
settings (https://www.freedesktop.org/software/systemd/man/systemd.link.html),
or any other method that would do a one-time setup during early boot.
Refactor the code so that fec_restart() instead uses
fec_enet_itr_coal_set(), which simply applies the settings that are
stored in the private data, and initialize that private data with the
default values.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a8e3bd25f ]
Microchip USB Analyzer can activate the internal termination resistors
by setting the "termination" option ON, or OFF to to deactivate them.
As I've observed, both with my oscilloscope and captured USB packets
below, you must send "0" to turn it ON, and "1" to turn it OFF.
From the schematics in the user's guide, I can confirm that you must
drive the CAN_RES signal LOW "0" to activate the resistors.
Reverse the argument value of usb_msg.termination to fix this.
These are the two commands sequence, ON then OFF.
> No. Time Source Destination Protocol Length Info
> 1 0.000000 host 1.3.1 USB 46 URB_BULK out
>
> Frame 1: 46 bytes on wire (368 bits), 46 bytes captured (368 bits)
> USB URB
> Leftover Capture Data: a80000000000000000000000000000000000a8
>
> No. Time Source Destination Protocol Length Info
> 2 4.372547 host 1.3.1 USB 46 URB_BULK out
>
> Frame 2: 46 bytes on wire (368 bits), 46 bytes captured (368 bits)
> USB URB
> Leftover Capture Data: a80100000000000000000000000000000000a9
Signed-off-by: Yasushi SHOJI <yashi@spacecubics.com>
Link: https://lore.kernel.org/all/20221124152504.125994-1-yashi@spacecubics.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 689eb2f1ba ]
Using page size as max_entries when probing ring buffer map, else the
probe may fail on host with 64KB page size (e.g., an ARM64 host).
After the fix, the output of "bpftool feature" on above host will be
correct.
Before :
eBPF map_type ringbuf is NOT available
eBPF map_type user_ringbuf is NOT available
After :
eBPF map_type ringbuf is available
eBPF map_type user_ringbuf is available
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20221116072351.1168938-2-houtao@huaweicloud.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 02e1a114fd upstream.
area_cache_get() is used to distribute cache->area and set cache->id,
and if cache->id is not 0 and cache->area->kref refcount is 0, it will
release the cache->area by nfp_cpp_area_release(). area_cache_get()
set cache->id before cpp->op->area_init() and nfp_cpp_area_acquire().
But if area_init() or nfp_cpp_area_acquire() fails, the cache->id is
is already set but the refcount is not increased as expected. At this
time, calling the nfp_cpp_area_release() will cause use-after-free.
To avoid the use-after-free, set cache->id after area_init() and
nfp_cpp_area_acquire() complete successfully.
Note: This vulnerability is triggerable by providing emulated device
equipped with specified configuration.
BUG: KASAN: use-after-free in nfp6000_area_init (drivers/net/ethernet/netronome/nfp/nfpcore/nfp6000_pcie.c:760)
Write of size 4 at addr ffff888005b7f4a0 by task swapper/0/1
Call Trace:
<TASK>
nfp6000_area_init (drivers/net/ethernet/netronome/nfp/nfpcore/nfp6000_pcie.c:760)
area_cache_get.constprop.8 (drivers/net/ethernet/netronome/nfp/nfpcore/nfp_cppcore.c:884)
Allocated by task 1:
nfp_cpp_area_alloc_with_name (drivers/net/ethernet/netronome/nfp/nfpcore/nfp_cppcore.c:303)
nfp_cpp_area_cache_add (drivers/net/ethernet/netronome/nfp/nfpcore/nfp_cppcore.c:802)
nfp6000_init (drivers/net/ethernet/netronome/nfp/nfpcore/nfp6000_pcie.c:1230)
nfp_cpp_from_operations (drivers/net/ethernet/netronome/nfp/nfpcore/nfp_cppcore.c:1215)
nfp_pci_probe (drivers/net/ethernet/netronome/nfp/nfp_main.c:744)
Freed by task 1:
kfree (mm/slub.c:4562)
area_cache_get.constprop.8 (drivers/net/ethernet/netronome/nfp/nfpcore/nfp_cppcore.c:873)
nfp_cpp_read (drivers/net/ethernet/netronome/nfp/nfpcore/nfp_cppcore.c:924 drivers/net/ethernet/netronome/nfp/nfpcore/nfp_cppcore.c:973)
nfp_cpp_readl (drivers/net/ethernet/netronome/nfp/nfpcore/nfp_cpplib.c:48)
Signed-off-by: Jialiang Wang <wangjialiang0806@163.com>
Reviewed-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Acked-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220810073057.4032-1-wangjialiang0806@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 10bc8e4af6 upstream.
Commit 868f9f2f8e ("vfs: fix copy_file_range() regression in cross-fs
copies") removed fallback to generic_copy_file_range() for cross-fs
cases inside vfs_copy_file_range().
To preserve behavior of nfsd and ksmbd server-side-copy, the fallback to
generic_copy_file_range() was added in nfsd and ksmbd code, but that
call is missing sb_start_write(), fsnotify hooks and more.
Ideally, nfsd and ksmbd would pass a flag to vfs_copy_file_range() that
will take care of the fallback, but that code would be subtle and we got
vfs_copy_file_range() logic wrong too many times already.
Instead, add a flag to explicitly request vfs_copy_file_range() to
perform only generic_copy_file_range() and let nfsd and ksmbd use this
flag only in the fallback path.
This choise keeps the logic changes to minimum in the non-nfsd/ksmbd code
paths to reduce the risk of further regressions.
Fixes: 868f9f2f8e ("vfs: fix copy_file_range() regression in cross-fs copies")
Tested-by: Namjae Jeon <linkinjeon@kernel.org>
Tested-by: Luis Henriques <lhenriques@suse.de>
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[backport comments for v5.15: - sb_write_started() is missing - assert was dropped ]
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45be2ad007 upstream.
Recently, ld.lld moved from '--undefined-version' to
'--no-undefined-version' as the default, which breaks building the vDSO
when CONFIG_X86_SGX is not set:
ld.lld: error: version script assignment of 'LINUX_2.6' to symbol '__vdso_sgx_enter_enclave' failed: symbol not defined
__vdso_sgx_enter_enclave is only included in the vDSO when
CONFIG_X86_SGX is set. Only export it if it will be present in the final
object, which clears up the error.
Fixes: 8466436952 ("x86/vdso: Implement a vDSO for Intel SGX enclave call")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://github.com/ClangBuiltLinux/linux/issues/1756
Link: https://lore.kernel.org/r/20221109000306.1407357-1-nathan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
VLI have a firmware update for the VL805 which resolves the incorrect
frame time calculation in the hub's TT. Limit applying the quirk to
known-bad firmwares.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Add a new overlay that disables the EMMC2 controller on BCM2711.
This can be useful on a Compute Module 4 if the onboard EMMC2
storage is unreliable and the system can be booted by other
means e.g Network / USB.
Signed-off-by: Tim Gover <tim.gover@raspberrypi.com>
CM4S follows the pattern of CM1&3 for routing camera
GPIO control, but didn't have the overrides defined to
allow enabling and configuring the camera regulator
GPIOs. Add them.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
To make it easier for custom routing of camera control GPIOs,
add the camX_reg_gpio parameter to CM4 DT as well.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The standard instructions for wiring up cameras on CM1&3
assign GPIOs for both the shutdown and LED pins on the
camera connectors.
The assignment in DT matched the LED wiring, not the shutdown
line, so didn't control the camera power correctly.
Update the base DT accordingly.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The legacy camera stack wiring instructions connect the cameras
to the opposite sets of GPIOs compared to the arrangement
more normally used with libcamera on all other platforms.
Add an overlay to allow easy swapping of the assignments so
that the legacy wiring can be used with libcamera.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The 'eee' dtparam allows EEE to be disabled on the onboard Ethernet
controller. Adding 'dtparam=eee=off' to config.txt causes
'genet.eee=N' to be added to the kernel command line, which in turn
tells the Genet driver to disable EEE.
See: https://github.com/raspberrypi/linux/issues/4289
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
On some switches, having EEE enabled causes the link to become
unstable. With this patch, adding 'genet.eee=N' to the kernel command
line will cause EEE to be disabled on the link.
See: https://github.com/raspberrypi/linux/issues/4289
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
See: https://github.com/raspberrypi/linux/issues/4446
The formula that determines the core clock requirement based on pixel clock and blanking
has been determined experimentally to minimise the clock while supporting all modes we've seen.
A new reduced blanking mode (4kp60 at 533MHz rather than the standard 594MHz) has been seen
that doesn't produce a high enough clock and results in "flip_done timed out" error.
Increase the setup cost in the formula to make this work.
The result is a reduced blanking mode increases by up to 7MHz while leaving the standard timing
mode untouched
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
[ Upstream commit 998b30c394 ]
Syzkaller reports a NULL deref bug as follows:
BUG: KASAN: null-ptr-deref in io_tctx_exit_cb+0x53/0xd3
Read of size 4 at addr 0000000000000138 by task file1/1955
CPU: 1 PID: 1955 Comm: file1 Not tainted 6.1.0-rc7-00103-gef4d3ea40565 #75
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.0-2.el7 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0xcd/0x134
? io_tctx_exit_cb+0x53/0xd3
kasan_report+0xbb/0x1f0
? io_tctx_exit_cb+0x53/0xd3
kasan_check_range+0x140/0x190
io_tctx_exit_cb+0x53/0xd3
task_work_run+0x164/0x250
? task_work_cancel+0x30/0x30
get_signal+0x1c3/0x2440
? lock_downgrade+0x6e0/0x6e0
? lock_downgrade+0x6e0/0x6e0
? exit_signals+0x8b0/0x8b0
? do_raw_read_unlock+0x3b/0x70
? do_raw_spin_unlock+0x50/0x230
arch_do_signal_or_restart+0x82/0x2470
? kmem_cache_free+0x260/0x4b0
? putname+0xfe/0x140
? get_sigframe_size+0x10/0x10
? do_execveat_common.isra.0+0x226/0x710
? lockdep_hardirqs_on+0x79/0x100
? putname+0xfe/0x140
? do_execveat_common.isra.0+0x238/0x710
exit_to_user_mode_prepare+0x15f/0x250
syscall_exit_to_user_mode+0x19/0x50
do_syscall_64+0x42/0xb0
entry_SYSCALL_64_after_hwframe+0x63/0xcd
RIP: 0023:0x0
Code: Unable to access opcode bytes at 0xffffffffffffffd6.
RSP: 002b:00000000fffb7790 EFLAGS: 00000200 ORIG_RAX: 000000000000000b
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000000
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
</TASK>
Kernel panic - not syncing: panic_on_warn set ...
This happens because the adding of task_work from io_ring_exit_work()
isn't synchronized with canceling all work items from eg exec. The
execution of the two are ordered in that they are both run by the task
itself, but if io_tctx_exit_cb() is queued while we're canceling all
work items off exec AND gets executed when the task exits to userspace
rather than in the main loop in io_uring_cancel_generic(), then we can
find current->io_uring == NULL and hit the above crash.
It's safe to add this NULL check here, because the execution of the two
paths are done by the task itself.
Cc: stable@vger.kernel.org
Fixes: d56d938b4b ("io_uring: do ctx initiated file note removal")
Reported-by: syzkaller <syzkaller@googlegroups.com>
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Link: https://lore.kernel.org/r/20221206093833.3812138-1-harshit.m.mogalapalli@oracle.com
[axboe: add code comment and also put an explanation in the commit msg]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed29b0b4fd ]
In preparation for splitting io_uring up a bit, move it into its own
top level directory. It didn't really belong in fs/ anyway, as it's
not a file system only API.
This adds io_uring/ and moves the core files in there, and updates the
MAINTAINERS file for the new location.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Stable-dep-of: 998b30c394 ("io_uring: Fix a null-ptr-deref in io_tctx_exit_cb()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 918ee4911f ]
We don't get any further EVENT from an esd CAN USB device for changes
on REC or TEC while those counters converge to 0 (with ecc == 0). So
when handling the "Back to Error Active"-event force txerr = rxerr =
0, otherwise the berr-counters might stay on values like 95 forever.
Also, to make life easier during the ongoing development a
netdev_dbg() has been introduced to allow dumping error events send by
an esd CAN USB device.
Fixes: 96d8e90382 ("can: Add driver for esd CAN-USB/2 device")
Signed-off-by: Frank Jungclaus <frank.jungclaus@esd.eu>
Link: https://lore.kernel.org/all/20221130202242.3998219-2-frank.jungclaus@esd.eu
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cdd97383e1 ]
In an earlier commit, I added a bounds check to prevent an out of bounds
read and a WARN(). On further discussion and consideration that check
was probably too aggressive. Instead of returning -EINVAL, a better fix
would be to just prevent the out of bounds read but continue the process.
Background: The value of "pp->rxq_def" is a number between 0-7 by default,
or even higher depending on the value of "rxq_number", which is a module
parameter. If the value is more than the number of available CPUs then
it will trigger the WARN() in cpu_max_bits_warn().
Fixes: e8b4fc1390 ("net: mvneta: Prevent out of bounds read in mvneta_config_rss()")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/Y5A7d1E5ccwHTYPf@kadam
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc3dd0367e ]
The commit 09ce6b2010 ("net: phy: mxl-gpy: add temperature sensor")
will overwrite the return value and the reported version will be wrong.
Fix it.
Fixes: 09ce6b2010 ("net: phy: mxl-gpy: add temperature sensor")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 5f4d487d01 ("net: phy: mxl-gpy: add MDINT workaround")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7dfa764e02 ]
Commit ad7f402ae4 ("xen/netback: Ensure protocol headers don't fall in
the non-linear area") introduced a (valid) build warning. There have
even been reports of this problem breaking networking of Xen guests.
Fixes: ad7f402ae4 ("xen/netback: Ensure protocol headers don't fall in the non-linear area")
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Tested-by: Jason Andryuk <jandryuk@gmail.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 88956177db ]
When sending packets between nodes in netns, it calls tipc_lxc_xmit() for
peer node to receive the packets where tipc_sk_mcast_rcv()/tipc_sk_rcv()
might be called, and it's pretty much like in tipc_rcv().
Currently the local 'node rw lock' is held during calling tipc_lxc_xmit()
to protect the peer_net not being freed by another thread. However, when
receiving these packets, tipc_node_add_conn() might be called where the
peer 'node rw lock' is acquired. Then a dead lock warning is triggered by
lockdep detector, although it is not a real dead lock:
WARNING: possible recursive locking detected
--------------------------------------------
conn_server/1086 is trying to acquire lock:
ffff8880065cb020 (&n->lock#2){++--}-{2:2}, \
at: tipc_node_add_conn.cold.76+0xaa/0x211 [tipc]
but task is already holding lock:
ffff8880065cd020 (&n->lock#2){++--}-{2:2}, \
at: tipc_node_xmit+0x285/0xb30 [tipc]
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&n->lock#2);
lock(&n->lock#2);
*** DEADLOCK ***
May be due to missing lock nesting notation
4 locks held by conn_server/1086:
#0: ffff8880036d1e40 (sk_lock-AF_TIPC){+.+.}-{0:0}, \
at: tipc_accept+0x9c0/0x10b0 [tipc]
#1: ffff8880036d5f80 (sk_lock-AF_TIPC/1){+.+.}-{0:0}, \
at: tipc_accept+0x363/0x10b0 [tipc]
#2: ffff8880065cd020 (&n->lock#2){++--}-{2:2}, \
at: tipc_node_xmit+0x285/0xb30 [tipc]
#3: ffff888012e13370 (slock-AF_TIPC){+...}-{2:2}, \
at: tipc_sk_rcv+0x2da/0x1b40 [tipc]
Call Trace:
<TASK>
dump_stack_lvl+0x44/0x5b
__lock_acquire.cold.77+0x1f2/0x3d7
lock_acquire+0x1d2/0x610
_raw_write_lock_bh+0x38/0x80
tipc_node_add_conn.cold.76+0xaa/0x211 [tipc]
tipc_sk_finish_conn+0x21e/0x640 [tipc]
tipc_sk_filter_rcv+0x147b/0x3030 [tipc]
tipc_sk_rcv+0xbb4/0x1b40 [tipc]
tipc_lxc_xmit+0x225/0x26b [tipc]
tipc_node_xmit.cold.82+0x4a/0x102 [tipc]
__tipc_sendstream+0x879/0xff0 [tipc]
tipc_accept+0x966/0x10b0 [tipc]
do_accept+0x37d/0x590
This patch avoids this warning by not holding the 'node rw lock' before
calling tipc_lxc_xmit(). As to protect the 'peer_net', rcu_read_lock()
should be enough, as in cleanup_net() when freeing the netns, it calls
synchronize_rcu() before the free is continued.
Also since tipc_lxc_xmit() is like the RX path in tipc_rcv(), it makes
sense to call it under rcu_read_lock(). Note that the right lock order
must be:
rcu_read_lock();
tipc_node_read_lock(n);
tipc_node_read_unlock(n);
tipc_lxc_xmit();
rcu_read_unlock();
instead of:
tipc_node_read_lock(n);
rcu_read_lock();
tipc_node_read_unlock(n);
tipc_lxc_xmit();
rcu_read_unlock();
and we have to call tipc_node_read_lock/unlock() twice in
tipc_node_xmit().
Fixes: f73b12812a ("tipc: improve throughput between nodes in netns")
Reported-by: Shuang Li <shuali@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Link: https://lore.kernel.org/r/5bdd1f8fee9db695cfff4528a48c9b9d0523fb00.1670110641.git.lucien.xin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c0d999348e ]
Cited commit added the table ID to the FIB info structure, but did not
properly initialize it when table ID 0 is used. This can lead to a route
in the default VRF with a preferred source address not being flushed
when the address is deleted.
Consider the following example:
# ip address add dev dummy1 192.0.2.1/28
# ip address add dev dummy1 192.0.2.17/28
# ip route add 198.51.100.0/24 via 192.0.2.2 src 192.0.2.17 metric 100
# ip route add table 0 198.51.100.0/24 via 192.0.2.2 src 192.0.2.17 metric 200
# ip route show 198.51.100.0/24
198.51.100.0/24 via 192.0.2.2 dev dummy1 src 192.0.2.17 metric 100
198.51.100.0/24 via 192.0.2.2 dev dummy1 src 192.0.2.17 metric 200
Both routes are installed in the default VRF, but they are using two
different FIB info structures. One with a metric of 100 and table ID of
254 (main) and one with a metric of 200 and table ID of 0. Therefore,
when the preferred source address is deleted from the default VRF,
the second route is not flushed:
# ip address del dev dummy1 192.0.2.17/28
# ip route show 198.51.100.0/24
198.51.100.0/24 via 192.0.2.2 dev dummy1 src 192.0.2.17 metric 200
Fix by storing a table ID of 254 instead of 0 in the route configuration
structure.
Add a test case that fails before the fix:
# ./fib_tests.sh -t ipv4_del_addr
IPv4 delete address route tests
Regular FIB info
TEST: Route removed from VRF when source address deleted [ OK ]
TEST: Route in default VRF not removed [ OK ]
TEST: Route removed in default VRF when source address deleted [ OK ]
TEST: Route in VRF is not removed by address delete [ OK ]
Identical FIB info with different table ID
TEST: Route removed from VRF when source address deleted [ OK ]
TEST: Route in default VRF not removed [ OK ]
TEST: Route removed in default VRF when source address deleted [ OK ]
TEST: Route in VRF is not removed by address delete [ OK ]
Table ID 0
TEST: Route removed in default VRF when source address deleted [FAIL]
Tests passed: 8
Tests failed: 1
And passes after:
# ./fib_tests.sh -t ipv4_del_addr
IPv4 delete address route tests
Regular FIB info
TEST: Route removed from VRF when source address deleted [ OK ]
TEST: Route in default VRF not removed [ OK ]
TEST: Route removed in default VRF when source address deleted [ OK ]
TEST: Route in VRF is not removed by address delete [ OK ]
Identical FIB info with different table ID
TEST: Route removed from VRF when source address deleted [ OK ]
TEST: Route in default VRF not removed [ OK ]
TEST: Route removed in default VRF when source address deleted [ OK ]
TEST: Route in VRF is not removed by address delete [ OK ]
Table ID 0
TEST: Route removed in default VRF when source address deleted [ OK ]
Tests passed: 9
Tests failed: 0
Fixes: 5a56a0b3a4 ("net: Don't delete routes in different VRFs")
Reported-by: Donald Sharp <sharpd@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f96a3d7455 ]
Cited commit added the table ID to the FIB info structure, but did not
prevent structures with different table IDs from being consolidated.
This can lead to routes being flushed from a VRF when an address is
deleted from a different VRF.
Fix by taking the table ID into account when looking for a matching FIB
info. This is already done for FIB info structures backed by a nexthop
object in fib_find_info_nh().
Add test cases that fail before the fix:
# ./fib_tests.sh -t ipv4_del_addr
IPv4 delete address route tests
Regular FIB info
TEST: Route removed from VRF when source address deleted [ OK ]
TEST: Route in default VRF not removed [ OK ]
TEST: Route removed in default VRF when source address deleted [ OK ]
TEST: Route in VRF is not removed by address delete [ OK ]
Identical FIB info with different table ID
TEST: Route removed from VRF when source address deleted [FAIL]
TEST: Route in default VRF not removed [ OK ]
RTNETLINK answers: File exists
TEST: Route removed in default VRF when source address deleted [ OK ]
TEST: Route in VRF is not removed by address delete [FAIL]
Tests passed: 6
Tests failed: 2
And pass after:
# ./fib_tests.sh -t ipv4_del_addr
IPv4 delete address route tests
Regular FIB info
TEST: Route removed from VRF when source address deleted [ OK ]
TEST: Route in default VRF not removed [ OK ]
TEST: Route removed in default VRF when source address deleted [ OK ]
TEST: Route in VRF is not removed by address delete [ OK ]
Identical FIB info with different table ID
TEST: Route removed from VRF when source address deleted [ OK ]
TEST: Route in default VRF not removed [ OK ]
TEST: Route removed in default VRF when source address deleted [ OK ]
TEST: Route in VRF is not removed by address delete [ OK ]
Tests passed: 8
Tests failed: 0
Fixes: 5a56a0b3a4 ("net: Don't delete routes in different VRFs")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb37617687 ]
There is warning report about of_node refcount leak
while probing mdio device:
OF: ERROR: memory leak, expected refcount 1 instead of 2,
of_node_get()/of_node_put() unbalanced - destroy cset entry:
attach overlay node /spi/soc@0/mdio@710700c0/ethernet@4
In of_mdiobus_register_device(), we increase fwnode refcount
by fwnode_handle_get() before associating the of_node with
mdio device, but it has never been decreased in normal path.
Since that, in mdio_device_release(), it needs to call
fwnode_handle_put() in addition instead of calling kfree()
directly.
After above, just calling mdio_device_free() in the error handle
path of of_mdiobus_register_device() is enough to keep the
refcount balanced.
Fixes: a9049e0c51 ("mdio: Add support for mdio drivers.")
Signed-off-by: Zeng Heng <zengheng4@huawei.com>
Reviewed-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20221203073441.3885317-1-zengheng4@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61d4f14094 ]
In dt-binding snps,dwmac.yaml, some properties under "snps,axi-config"
node are named without "axi_" prefix, but the driver expects the
prefix. Since the dt-binding has been there for a long time, we'd
better make driver match the binding for compatibility.
Fixes: afea03656a ("stmmac: rework DMA bus setting and introduce new platform AXI structure")
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Link: https://lore.kernel.org/r/20221202161739.2203-1-jszhang@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63ff545af7 ]
The node returned by of_get_parent() with refcount incremented,
of_node_put() needs be called when finish using it. So add it in the
end of of_pinctrl_get().
Fixes: 936ee2675e ("gpio/rockchip: add driver for rockchip gpio")
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f2d71524b ]
A device might have a core quirk for NVME_QUIRK_IGNORE_DEV_SUBNQN
(such as Samsung X5) but it would still give a:
"missing or invalid SUBNQN field"
warning as core quirks are filled after calling nvme_init_subnqn. Fill
ctrl->quirks from struct core_quirks before calling nvme_init_subsystem
to fix this.
Tested on a Samsung X5.
Fixes: ab9e00cc72 ("nvme: track subsystems")
Signed-off-by: Pankaj Raghav <p.raghav@samsung.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d64aaf3f78 ]
Return -EOPNOTSUPP, when user requests l4_4_bytes for raw IP4 or
IP6 flow director filters. Flow director does not support filtering
on l4 bytes for PCTYPEs used by IP4 and IP6 filters.
Without this patch, user could create filters with l4_4_bytes fields,
which did not do any filtering on L4, but only on L3 fields.
Fixes: 36777d9fa2 ("i40e: check current configured input set when adding ntuple filters")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Kamil Maziarz <kamil.maziarz@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0850197047 ]
After spawning max VFs on a PF, some VFs were not getting resources and
their MAC addresses were 0. This was caused by PF sleeping before flushing
HW registers which caused VIRTCHNL_VFR_VFACTIVE to not be set in time for
VF.
Fix by adding a sleep after hw flush.
Fixes: e4b433f4a7 ("i40e: reset all VFs in parallel when rebuilding PF")
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 82e0572b23 ]
During tx rings configuration default XPS queue config is set and
__I40E_TX_XPS_INIT_DONE is locked. __I40E_TX_XPS_INIT_DONE state is
cleared and set again with default mapping only during queues build,
it means after first setup or reset with queues rebuild. (i.e.
ethtool -L <interface> combined <number>) After other resets (i.e.
ethtool -t <interface>) XPS_INIT_DONE is not cleared and those default
maps cannot be set again. It results in cleared xps_cpus mapping
until queues are not rebuild or mapping is not set by user.
Add clearing __I40E_TX_XPS_INIT_DONE state during reset to let
the driver set xps_cpus to defaults again after it was cleared.
Fixes: 6f853d4f8e ("i40e: allow XPS with QoS enabled")
Signed-off-by: Michal Jaron <michalx.jaron@intel.com>
Signed-off-by: Kamil Maziarz <kamil.maziarz@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8b4fc1390 ]
The pp->indir[0] value comes from the user. It is passed to:
if (cpu_online(pp->rxq_def))
inside the mvneta_percpu_elect() function. It needs bounds checkeding
to ensure that it is not beyond the end of the cpu bitmap.
Fixes: cad5d847a0 ("net: mvneta: Fix the CPU choice in mvneta_percpu_elect")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d50b7914fa ]
A NAPI is setup for each network sring to poll data to kernel
The sring with source host is destroyed before live migration and
new sring with target host is setup after live migration.
The NAPI for the old sring is not deleted until setup new sring
with target host after migration. With busy_poll/busy_read enabled,
the NAPI can be polled before got deleted when resume VM.
BUG: unable to handle kernel NULL pointer dereference at
0000000000000008
IP: xennet_poll+0xae/0xd20
PGD 0 P4D 0
Oops: 0000 [#1] SMP PTI
Call Trace:
finish_task_switch+0x71/0x230
timerqueue_del+0x1d/0x40
hrtimer_try_to_cancel+0xb5/0x110
xennet_alloc_rx_buffers+0x2a0/0x2a0
napi_busy_loop+0xdb/0x270
sock_poll+0x87/0x90
do_sys_poll+0x26f/0x580
tracing_map_insert+0x1d4/0x2f0
event_hist_trigger+0x14a/0x260
finish_task_switch+0x71/0x230
__schedule+0x256/0x890
recalc_sigpending+0x1b/0x50
xen_sched_clock+0x15/0x20
__rb_reserve_next+0x12d/0x140
ring_buffer_lock_reserve+0x123/0x3d0
event_triggers_call+0x87/0xb0
trace_event_buffer_commit+0x1c4/0x210
xen_clocksource_get_cycles+0x15/0x20
ktime_get_ts64+0x51/0xf0
SyS_ppoll+0x160/0x1a0
SyS_ppoll+0x160/0x1a0
do_syscall_64+0x73/0x130
entry_SYSCALL_64_after_hwframe+0x41/0xa6
...
RIP: xennet_poll+0xae/0xd20 RSP: ffffb4f041933900
CR2: 0000000000000008
---[ end trace f8601785b354351c ]---
xen frontend should remove the NAPIs for the old srings before live
migration as the bond srings are destroyed
There is a tiny window between the srings are set to NULL and
the NAPIs are disabled, It is safe as the NAPI threads are still
frozen at that time
Signed-off-by: Lin Liu <lin.liu@citrix.com>
Fixes: 4ec2411980 ([NET]: Do not check netif_running() and carrier state in ->poll())
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fbf33f5ac7 ]
In otx2_init_tc(), if rhashtable_init() failed, it does not free
tc->tc_entries_bitmap which is allocated in otx2_tc_alloc_ent_bitmap().
Fixes: 2e2a8126ff ("octeontx2-pf: Unify flow management variables")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 165df24186 ]
If phy_device_register() or fwnode_mdiobus_phy_device_register()
fail, phy_device_free() is called, the device refcount is decreased
to 0, then fwnode_handle_put() will be called in phy_device_release(),
but in the error path, fwnode_handle_put() has already been called,
so set fwnode to NULL after fwnode_handle_put() in the error path to
avoid double put.
Fixes: cdde156011 ("net: mdiobus: fix unbalanced node reference count")
Reported-by: Zeng Heng <zengheng4@huawei.com>
Tested-by: Zeng Heng <zengheng4@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Zeng Heng <zengheng4@huawei.com>
Tested-by: Zeng Heng <zengheng4@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cfaa202a73 ]
Rework error handling as preparation for PSE patch. This patch should
make it easier to extend this function.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 165df24186 ("net: mdiobus: fix double put fwnode in the error path")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 25f427ac7b ]
A loop for reading MISTAT register continues while regmap_read() fails
and (mistat & BUSY), but if regmap_read() fails a value of mistat is
undefined.
The patch proposes to check for BUSY flag only when regmap_read()
succeed. Compile test only.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: d70e53262f ("net: Microchip encx24j600 driver")
Signed-off-by: Valentina Goncharenko <goncharenko.vp@ispras.ru>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 167b3f2dcc ]
In functions regmap_encx24j600_phy_reg_read() and
regmap_encx24j600_phy_reg_write() in the conditions of the waiting
cycles for filling the variable 'ret' it is necessary to add parentheses
to prevent wrong assignment due to logical operations precedence.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: d70e53262f ("net: Microchip encx24j600 driver")
Signed-off-by: Valentina Goncharenko <goncharenko.vp@ispras.ru>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3d72d3135 ]
Kernel fault injection test reports null-ptr-deref as follows:
BUG: kernel NULL pointer dereference, address: 0000000000000008
RIP: 0010:cfg802154_netdev_notifier_call+0x120/0x310 include/linux/list.h:114
Call Trace:
<TASK>
raw_notifier_call_chain+0x6d/0xa0 kernel/notifier.c:87
call_netdevice_notifiers_info+0x6e/0xc0 net/core/dev.c:1944
unregister_netdevice_many_notify+0x60d/0xcb0 net/core/dev.c:1982
unregister_netdevice_queue+0x154/0x1a0 net/core/dev.c:10879
register_netdevice+0x9a8/0xb90 net/core/dev.c:10083
ieee802154_if_add+0x6ed/0x7e0 net/mac802154/iface.c:659
ieee802154_register_hw+0x29c/0x330 net/mac802154/main.c:229
mcr20a_probe+0xaaa/0xcb1 drivers/net/ieee802154/mcr20a.c:1316
ieee802154_if_add() allocates wpan_dev as netdev's private data, but not
init the list in struct wpan_dev. cfg802154_netdev_notifier_call() manage
the list when device register/unregister, and may lead to null-ptr-deref.
Use INIT_LIST_HEAD() on it to initialize it correctly.
Fixes: fcf39e6e88 ("ieee802154: add wpan_dev_list")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20221130091705.1831140-1-weiyongjun@huaweicloud.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f3957c7eb ]
bt_init() calls bt_leds_init() to register led, but if it fails later,
bt_leds_cleanup() is not called to unregister it.
This can cause panic if the argument "bluetooth-power" in text is freed
and then another led_trigger_register() tries to access it:
BUG: unable to handle page fault for address: ffffffffc06d3bc0
RIP: 0010:strcmp+0xc/0x30
Call Trace:
<TASK>
led_trigger_register+0x10d/0x4f0
led_trigger_register_simple+0x7d/0x100
bt_init+0x39/0xf7 [bluetooth]
do_one_initcall+0xd0/0x4e0
Fixes: e64c97b53b ("Bluetooth: Add combined LED trigger for controller power")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 747da1308b ]
hci_get_route() takes reference, we should use hci_dev_put() to release
it when not need anymore.
Fixes: 6b8d4a6a03 ("Bluetooth: 6LoWPAN: Use connected oriented channel instead of fixed one")
Signed-off-by: Wang ShaoBo <bobo.shaobowang@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 409e8ec8c5 ]
Commit 39f9895a00 ("vmxnet3: add support for 32 Tx/Rx queues")
added support for 32Tx/Rx queues. As a part of this patch, intrConf
structure was extended to incorporate increased queues.
This patch fixes the issue where incorrect reference is being used.
Fixes: 39f9895a00 ("vmxnet3: add support for 32 Tx/Rx queues")
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Acked-by: Guolin Yang <gyang@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 40b8c2a1af ]
Commit dacce2be33 ("vmxnet3: add geneve and vxlan tunnel offload
support") added support for encapsulation offload. However, the
pathc did not report correctly the encapsulated packet which is
LRO'ed by the hypervisor.
This patch fixes this issue by using correct callback for the LRO'ed
encapsulated packet.
Fixes: dacce2be33 ("vmxnet3: add geneve and vxlan tunnel offload support")
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Acked-by: Guolin Yang <gyang@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3d6b1bf85 ]
Cheap monitors sometimes advertise YUV modes they don't really have
(HDMI specification mandates YUV support so even monitors without actual
support will often wrongfully advertise it) which results in YUV matches
and user forum complaints of a red tint to light colour display areas in
common desktop environments.
Moving the default RGB fall-back before YUV selection results in RGB
mode matching in most cases, reducing complaints.
Fixes: 6c3c719936 ("drm/bridge: synopsys: dw-hdmi: add bus format negociation")
Signed-off-by: Guillaume BRUN <the.cheaterman@gmail.com>
Tested-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20221116143523.2126-1-the.cheaterman@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 421f8663b3 ]
commit 8d820bc9d1 ("net: broadcom: Fix BCMGENET Kconfig") fixes the build
that contain 99addbe31f ("net: broadcom: Select BROADCOM_PHY for BCMGENET")
and enable BCMGENET=y but PTP_1588_CLOCK_OPTIONAL=m, which otherwise
leads to a link failure. However this may trigger a runtime failure.
Fix the original issue by propagating the PTP_1588_CLOCK_OPTIONAL dependency
of BROADCOM_PHY down to BCMGENET.
Fixes: 8d820bc9d1 ("net: broadcom: Fix BCMGENET Kconfig")
Fixes: 99addbe31f ("net: broadcom: Select BROADCOM_PHY for BCMGENET")
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20221125115003.30308-1-yuehaibing@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28e96556ba ]
Without this change, the interrupt test fail with MSI-X environment:
$ sudo ethtool -t enp0s2 offline
[ 43.921783] igb 0000:00:02.0: offline testing starting
[ 44.855824] igb 0000:00:02.0 enp0s2: igb: enp0s2 NIC Link is Down
[ 44.961249] igb 0000:00:02.0 enp0s2: igb: enp0s2 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[ 51.272202] igb 0000:00:02.0: testing shared interrupt
[ 56.996975] igb 0000:00:02.0 enp0s2: igb: enp0s2 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
The test result is FAIL
The test extra info:
Register test (offline) 0
Eeprom test (offline) 0
Interrupt test (offline) 4
Loopback test (offline) 0
Link test (on/offline) 0
Here, "4" means an expected interrupt was not delivered.
To fix this, route IRQs correctly to the first MSI-X vector by setting
IVAR_MISC. Also, set bit 0 of EIMS so that the vector will not be
masked. The interrupt test now runs properly with this change:
$ sudo ethtool -t enp0s2 offline
[ 42.762985] igb 0000:00:02.0: offline testing starting
[ 50.141967] igb 0000:00:02.0: testing shared interrupt
[ 56.163957] igb 0000:00:02.0 enp0s2: igb: enp0s2 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
The test result is PASS
The test extra info:
Register test (offline) 0
Eeprom test (offline) 0
Interrupt test (offline) 0
Loopback test (offline) 0
Link test (on/offline) 0
Fixes: 4eefa8f013 ("igb: add single vector msi-x testing to interrupt test")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eed913f691 ]
e1000_xmit_frame is expected to stop the queue and dispatch frames to
hardware if there is not sufficient space for the next frame in the
buffer, but sometimes it failed to do so because the estimated maximum
size of frame was wrong. As the consequence, the later invocation of
e1000_xmit_frame failed with NETDEV_TX_BUSY, and the frame in the buffer
remained forever, resulting in a watchdog failure.
This change fixes the estimated size by making it match with the
condition for NETDEV_TX_BUSY. Apparently, the old estimation failed to
account for the following lines which determines the space requirement
for not causing NETDEV_TX_BUSY:
```
/* reserve a descriptor for the offload context */
if ((mss) || (skb->ip_summed == CHECKSUM_PARTIAL))
count++;
count++;
count += DIV_ROUND_UP(len, adapter->tx_fifo_limit);
```
This issue was found when running http-stress02 test included in Linux
Test Project 20220930 on QEMU with the following commandline:
```
qemu-system-x86_64 -M q35,accel=kvm -m 8G -smp 8
-drive if=virtio,format=raw,file=root.img,file.locking=on
-device e1000e,netdev=netdev
-netdev tap,script=ifup,downscript=no,id=netdev
```
Fixes: bc7f75fa97 ("[E1000E]: New pci-express e1000 driver (currently for ICH9 devices only)")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 45fecdb9f6 ]
for_each_pci_dev() is implemented by pci_get_device(). The comment of
pci_get_device() says that it will increase the reference count for the
returned pci_dev and also decrease the reference count for the input
pci_dev @from if it is not NULL.
If we break for_each_pci_dev() loop with pdev not NULL, we need to call
pci_dev_put() to decrease the reference count. Add the missing
pci_dev_put() after the 'out' label. Since pci_dev_put() can handle NULL
input parameter, there is no problem for the 'Device not found' branch.
For the normal path, add pci_dev_put() in amd_gpio_exit().
Fixes: f942a7de04 ("gpio: add a driver for GPIO pins found on AMD-8111 south bridge chips")
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c11586450 ]
According to the description in ti-sn65dsi86's datasheet:
CHA_HSYNC_POLARITY:
0 = Active High Pulse. Synchronization signal is high for the sync
pulse width. (default)
1 = Active Low Pulse. Synchronization signal is low for the sync
pulse width.
CHA_VSYNC_POLARITY:
0 = Active High Pulse. Synchronization signal is high for the sync
pulse width. (Default)
1 = Active Low Pulse. Synchronization signal is low for the sync
pulse width.
We should only set these bits when the polarity is negative.
Fixes: a095f15c00 ("drm/bridge: add support for sn65dsi86 bridge driver")
Signed-off-by: Qiqi Zhang <eddy.zhang@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20221125104558.84616-1-eddy.zhang@rock-chips.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e24c54da2 ]
The struct cas_control embeds multiple generic SPI structures and we
have to make sure these structures are initialized to default values.
This driver does not set all attributes. When using kmalloc before some
attributes were not initialized and contained random data which caused
random crashes at bootup.
Fixes: ded845a781 ("ieee802154: Add CA8210 IEEE 802.15.4 device driver")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://lore.kernel.org/r/20221121002201.1339636-1-hauke@hauke-m.de
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 97d4d394b5 ]
Embarrassingly, nft_pipapo_insert() checked for interval validity in
the first field only.
The start_p and end_p pointers were reset to key data from the first
field at every iteration of the loop which was supposed to go over
the set fields.
Fixes: 3c4287f620 ("nf_tables: Add set type for arbitrary concatenation of ranges")
Reported-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec851b2308 ]
Here is a backtrace report about memory leak detected in
gpiochip_setup_dev():
unreferenced object 0xffff88810b406400 (size 512):
comm "python3", pid 1682, jiffies 4295346908 (age 24.090s)
backtrace:
kmalloc_trace
device_add device_private_init at drivers/base/core.c:3361
(inlined by) device_add at drivers/base/core.c:3411
cdev_device_add
gpiolib_cdev_register
gpiochip_setup_dev
gpiochip_add_data_with_key
gcdev_register() & gcdev_unregister() would call device_add() &
device_del() (no matter CONFIG_GPIO_CDEV is enabled or not) to
register/unregister device.
However, if device_add() succeeds, some resource (like
struct device_private allocated by device_private_init())
is not released by device_del().
Therefore, after device_add() succeeds by gcdev_register(), it
needs to call put_device() to release resource in the error handle
path.
Here we move forward the register of release function, and let it
release every piece of resource by put_device() instead of kfree().
While at it, fix another subtle issue, i.e. when gc->ngpio is equal
to 0, we still call kcalloc() and, in case of further error, kfree()
on the ZERO_PTR pointer, which is not NULL. It's not a bug per se,
but rather waste of the resources and potentially wrong expectation
about contents of the gdev->descs variable.
Fixes: 159f3cd92f ("gpiolib: Defer gpio device setup until after gpiolib initialization")
Signed-off-by: Zeng Heng <zengheng4@huawei.com>
Co-developed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9dbd1ab205 ]
Several drivers read the 'ngpios' device property on their own, but
since it's defined as a standard GPIO property in the device tree bindings
anyway, it's a good candidate for generalization. If the driver didn't
set its gc->ngpio, try to read the 'ngpios' property from the GPIO
device's firmware node before bailing out.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Stable-dep-of: ec851b2308 ("gpiolib: fix memory leak in gpiochip_setup_dev()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5ab49cd3d ]
Drop unneeded whitespaces and put the variables of the same type
together for consistency with the rest of the code.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Stable-dep-of: ec851b2308 ("gpiolib: fix memory leak in gpiochip_setup_dev()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9ad6645a9d upstream.
The Acer Aspire Switch V 10 (SW5-017)'s keyboard-dock uses the same
ITE controller setup as other Acer Switch 2-in-1's.
This needs special handling for the wifi on/off toggle hotkey as well as
to properly report touchpad on/off keypresses.
Add the USB-ids for the SW5-017's keyboard-dock with a quirk setting of
QUIRK_TOUCHPAD_ON_OFF_REPORT to fix both issues.
Cc: Rudolf Polzer <rpolzer@google.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ec61b41918 upstream.
Syzbot reported shift-out-of-bounds in hid_report_raw_event.
microsoft 0003:045E:07DA.0001: hid_field_extract() called with n (128) >
32! (swapper/0)
======================================================================
UBSAN: shift-out-of-bounds in drivers/hid/hid-core.c:1323:20
shift exponent 127 is too large for 32-bit type 'int'
CPU: 0 PID: 0 Comm: swapper/0 Not tainted
6.1.0-rc4-syzkaller-00159-g4bbf3422df78 #0
Hardware name: Google Compute Engine/Google Compute Engine, BIOS
Google 10/26/2022
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x1e3/0x2cb lib/dump_stack.c:106
ubsan_epilogue lib/ubsan.c:151 [inline]
__ubsan_handle_shift_out_of_bounds+0x3a6/0x420 lib/ubsan.c:322
snto32 drivers/hid/hid-core.c:1323 [inline]
hid_input_fetch_field drivers/hid/hid-core.c:1572 [inline]
hid_process_report drivers/hid/hid-core.c:1665 [inline]
hid_report_raw_event+0xd56/0x18b0 drivers/hid/hid-core.c:1998
hid_input_report+0x408/0x4f0 drivers/hid/hid-core.c:2066
hid_irq_in+0x459/0x690 drivers/hid/usbhid/hid-core.c:284
__usb_hcd_giveback_urb+0x369/0x530 drivers/usb/core/hcd.c:1671
dummy_timer+0x86b/0x3110 drivers/usb/gadget/udc/dummy_hcd.c:1988
call_timer_fn+0xf5/0x210 kernel/time/timer.c:1474
expire_timers kernel/time/timer.c:1519 [inline]
__run_timers+0x76a/0x980 kernel/time/timer.c:1790
run_timer_softirq+0x63/0xf0 kernel/time/timer.c:1803
__do_softirq+0x277/0x75b kernel/softirq.c:571
__irq_exit_rcu+0xec/0x170 kernel/softirq.c:650
irq_exit_rcu+0x5/0x20 kernel/softirq.c:662
sysvec_apic_timer_interrupt+0x91/0xb0 arch/x86/kernel/apic/apic.c:1107
======================================================================
If the size of the integer (unsigned n) is bigger than 32 in snto32(),
shift exponent will be too large for 32-bit type 'int', resulting in a
shift-out-of-bounds bug.
Fix this by adding a check on the size of the integer (unsigned n) in
snto32(). To add support for n greater than 32 bits, set n to 32, if n
is greater than 32.
Reported-by: syzbot+8b1641d2f14732407e23@syzkaller.appspotmail.com
Fixes: dde5845a52 ("[PATCH] Generic HID layer - code split")
Signed-off-by: ZhangPeng <zhangpeng362@huawei.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d180b64961 upstream.
If an empty buf is received, lbuf is also empty. So lbuf is
accessed by index -1.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: f31a2de3fe ("HID: hid-lg4ff: Allow switching of Logitech gaming wheels between compatibility modes")
Signed-off-by: Anastasia Belova <abelova@astralinux.ru>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f6d910a89a upstream.
Some additional USB mouse devices are needing ALWAYS_POLL quirk without
which they disconnect and reconnect every 60s.
Add below devices to the known quirk list.
CHERRY VID 0x046a, PID 0x000c
MICROSOFT VID 0x045e, PID 0x0783
PRIMAX VID 0x0461, PID 0x4e2a
Signed-off-by: Ankit Patel <anpatel@nvidia.com>
Signed-off-by: Haotien Hsu <haotienh@nvidia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f8bac7f9fd upstream.
The SJA1105 family has 45 L2 policing table entries
(SJA1105_MAX_L2_POLICING_COUNT) and SJA1110 has 110
(SJA1110_MAX_L2_POLICING_COUNT). Keeping the table structure but
accounting for the difference in port count (5 in SJA1105 vs 10 in
SJA1110) does not fully explain the difference. Rather, the SJA1110 also
has L2 ingress policers for multicast traffic. If a packet is classified
as multicast, it will be processed by the policer index 99 + SRCPORT.
The sja1105_init_l2_policing() function initializes all L2 policers such
that they don't interfere with normal packet reception by default. To have
a common code between SJA1105 and SJA1110, the index of the multicast
policer for the port is calculated because it's an index that is out of
bounds for SJA1105 but in bounds for SJA1110, and a bounds check is
performed.
The code fails to do the proper thing when determining what to do with the
multicast policer of port 0 on SJA1105 (ds->num_ports = 5). The "mcast"
index will be equal to 45, which is also equal to
table->ops->max_entry_count (SJA1105_MAX_L2_POLICING_COUNT). So it passes
through the check. But at the same time, SJA1105 doesn't have multicast
policers. So the code programs the SHARINDX field of an out-of-bounds
element in the L2 Policing table of the static config.
The comparison between index 45 and 45 entries should have determined the
code to not access this policer index on SJA1105, since its memory wasn't
even allocated.
With enough bad luck, the out-of-bounds write could even overwrite other
valid kernel data, but in this case, the issue was detected using KASAN.
Kernel log:
sja1105 spi5.0: Probed switch chip: SJA1105Q
==================================================================
BUG: KASAN: slab-out-of-bounds in sja1105_setup+0x1cbc/0x2340
Write of size 8 at addr ffffff880bd57708 by task kworker/u8:0/8
...
Workqueue: events_unbound deferred_probe_work_func
Call trace:
...
sja1105_setup+0x1cbc/0x2340
dsa_register_switch+0x1284/0x18d0
sja1105_probe+0x748/0x840
...
Allocated by task 8:
...
sja1105_setup+0x1bcc/0x2340
dsa_register_switch+0x1284/0x18d0
sja1105_probe+0x748/0x840
...
Fixes: 38fbe91f22 ("net: dsa: sja1105: configure the multicast policers, if present")
CC: stable@vger.kernel.org # 5.15+
Signed-off-by: Radu Nicolae Pirea (OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20221207132347.38698-1-radu-nicolae.pirea@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e90293618 upstream.
When SEV is enabled gmr's and mob's are explicitly disabled because
the encrypted system memory can not be used by the hypervisor.
The driver was disabling GMR's but the presentation code, which depends
on GMR's, wasn't honoring it which lead to black screen on hosts
with SEV enabled.
Make sure screen objects presentation is not used when guest memory
regions have been disabled to fix presentation on SEV enabled hosts.
Fixes: 3b0d6458c7 ("drm/vmwgfx: Refuse DMA operation when SEV encryption is active")
Cc: <stable@vger.kernel.org> # v5.7+
Signed-off-by: Zack Rusin <zackr@vmware.com>
Reported-by: Nicholas Hunt <nhunt@vmware.com>
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221201175341.491884-1-zack@kde.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 18010ff776 upstream.
After calling napi_complete_done(), the NAPIF_STATE_SCHED bit may be
cleared, and another CPU can start napi thread and access per-CQ variable,
cq->work_done. If the other thread (for example, from busy_poll) sets
it to a value >= budget, this thread will continue to run when it should
stop, and cause memory corruption and panic.
To fix this issue, save the per-CQ work_done variable in a local variable
before napi_complete_done(), so it won't be corrupted by a possible
concurrent thread after napi_complete_done().
Also, add a flag bit to advertise to the NIC firmware: the NAPI work_done
variable race is fixed, so the driver is able to reliably support features
like busy_poll.
Cc: stable@vger.kernel.org
Fixes: e1b5683ff6 ("net: mana: Move NAPI from EQ to CQ")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Link: https://lore.kernel.org/r/1670010190-28595-1-git-send-email-haiyangz@microsoft.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 955aebd445 upstream.
The rationale of showing this is that it's potentially critical
information to diagnose and find more CSR compatibility bugs in the
future and it will save a lot of headaches.
Given that clones come from a wide array of vendors (some are actually
Barrot, some are something else) and these numbers are what let us find
differences between actual and fake ones, it will be immensely helpful
to scour the Internet looking for this pattern and building an actual
database to find correlations and improve the checks.
Cc: stable@vger.kernel.org
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a7ba45b1a upstream.
memcg_write_event_control() accesses the dentry->d_name of the specified
control fd to route the write call. As a cgroup interface file can't be
renamed, it's safe to access d_name as long as the specified file is a
regular cgroup file. Also, as these cgroup interface files can't be
removed before the directory, it's safe to access the parent too.
Prior to 347c4a8747 ("memcg: remove cgroup_event->cft"), there was a
call to __file_cft() which verified that the specified file is a regular
cgroupfs file before further accesses. The cftype pointer returned from
__file_cft() was no longer necessary and the commit inadvertently dropped
the file type check with it allowing any file to slip through. With the
invarients broken, the d_name and parent accesses can now race against
renames and removals of arbitrary files and cause use-after-free's.
Fix the bug by resurrecting the file type check in __file_cft(). Now that
cgroupfs is implemented through kernfs, checking the file operations needs
to go through a layer of indirection. Instead, let's check the superblock
and dentry type.
Link: https://lkml.kernel.org/r/Y5FRm/cfcKPGzWwl@slm.duckdns.org
Fixes: 347c4a8747 ("memcg: remove cgroup_event->cft")
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Jann Horn <jannh@google.com>
Acked-by: Roman Gushchin <roman.gushchin@linux.dev>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Muchun Song <songmuchun@bytedance.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: <stable@vger.kernel.org> [3.14+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5eef214177 upstream.
Sanity checks were added to verify the v4l2_bt_timings blanking fields
in order to avoid integer overflows when userspace passes weird values.
But that assumed that userspace would correctly fill in the front porch,
backporch and sync values, but sometimes all you know is the total
blanking, which is then assigned to just one of these fields.
And that can fail with these checks.
So instead set a maximum for the total horizontal and vertical
blanking and check that each field remains below that.
That is still sufficient to avoid integer overflows, but it also
allows for more flexibility in how userspace fills in these fields.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 4b6d66a45e ("media: v4l2-dv-timings: add sanity checks for blanking values")
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 13c30a7558 upstream.
The bus->clk_stop_timeout member is only initialized to a non-zero value
during the codec driver probe. This can lead to corner cases where this
value remains pegged at zero when the bus suspends, which results in an
endless loop in sdw_bus_wait_for_clk_prep_deprep().
Corner cases include configurations with no codecs described in the
firmware, or delays in probing codec drivers.
Initializing the default timeout to the smallest non-zero value avoid this
problem and allows for the existing logic to be preserved: the
bus->clk_stop_timeout is set as the maximum required by all codecs
connected on the bus.
Fixes: 1f2dcf3a15 ("soundwire: intel: set dev_num_ida_min")
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Chao Song <chao.song@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20221020015624.1703950-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 098e5edc5d ]
While vb2_mmap took the mmap_lock mutex, vb2_get_unmapped_area didn't.
Add this.
Also take this opportunity to move the 'q->memory != VB2_MEMORY_MMAP'
check and vb2_fileio_is_active() check into __find_plane_by_offset() so
both vb2_mmap and vb2_get_unmapped_area do the same checks.
Since q->memory is checked while mmap_lock is held, also take that lock
in reqbufs and create_bufs when it is set, and set it back to
MEMORY_UNKNOWN on error.
Fixes: f035eb4e97 ("[media] videobuf2: fix lockdep warning")
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 74e7e1efda ]
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So remove kfree_skb()
from the spin_lock_irqsave() section and use the already existing
"drop" label in xenvif_start_xmit() for dropping the SKB. At the
same time replace the dev_kfree_skb() call there with a call of
dev_kfree_skb_any(), as xenvif_start_xmit() can be called with
disabled interrupts.
This is XSA-424 / CVE-2022-42328 / CVE-2022-42329.
Fixes: be81992f90 ("xen/netback: don't queue unlimited number of packages")
Reported-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad7f402ae4 ]
In some cases, the frontend may send a packet where the protocol headers
are spread across multiple slots. This would result in netback creating
an skb where the protocol headers spill over into the non-linear area.
Some drivers and NICs don't handle this properly resulting in an
interface reset or worse.
This issue was introduced by the removal of an unconditional skb pull in
the tx path to improve performance. Fix this without reintroducing the
pull by setting up grant copy ops for as many slots as needed to reach
the XEN_NETBACK_TX_COPY_LEN size. Adjust the rest of the code to handle
multiple copy operations per skb.
This is XSA-423 / CVE-2022-3643.
Fixes: 7e5d775395 ("xen-netback: remove unconditional __pskb_pull_tail() in guest Tx path")
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 153695d36e ]
`hostname` needs to be set as null-pointer after free in
`cifs_put_tcp_session` function, or when `cifsd` thread attempts
to resolve hostname and reconnect the host, the thread would deref
the invalid pointer.
Here is one of practical backtrace examples as reference:
Task 477
---------------------------
do_mount
path_mount
do_new_mount
vfs_get_tree
smb3_get_tree
smb3_get_tree_common
cifs_smb3_do_mount
cifs_mount
mount_put_conns
cifs_put_tcp_session
--> kfree(server->hostname)
cifsd
---------------------------
kthread
cifs_demultiplex_thread
cifs_reconnect
reconn_set_ipaddr_from_hostname
--> if (!server->hostname)
--> if (server->hostname[0] == '\0') // !! UAF fault here
CIFS: VFS: cifs_mount failed w/return code = -112
mount error(112): Host is down
BUG: KASAN: use-after-free in reconn_set_ipaddr_from_hostname+0x2ba/0x310
Read of size 1 at addr ffff888108f35380 by task cifsd/480
CPU: 2 PID: 480 Comm: cifsd Not tainted 6.1.0-rc2-00106-gf705792f89dd-dirty #25
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x68/0x85
print_report+0x16c/0x4a3
kasan_report+0x95/0x190
reconn_set_ipaddr_from_hostname+0x2ba/0x310
__cifs_reconnect.part.0+0x241/0x800
cifs_reconnect+0x65f/0xb60
cifs_demultiplex_thread+0x1570/0x2570
kthread+0x2c5/0x380
ret_from_fork+0x22/0x30
</TASK>
Allocated by task 477:
kasan_save_stack+0x1e/0x40
kasan_set_track+0x21/0x30
__kasan_kmalloc+0x7e/0x90
__kmalloc_node_track_caller+0x52/0x1b0
kstrdup+0x3b/0x70
cifs_get_tcp_session+0xbc/0x19b0
mount_get_conns+0xa9/0x10c0
cifs_mount+0xdf/0x1970
cifs_smb3_do_mount+0x295/0x1660
smb3_get_tree+0x352/0x5e0
vfs_get_tree+0x8e/0x2e0
path_mount+0xf8c/0x1990
do_mount+0xee/0x110
__x64_sys_mount+0x14b/0x1f0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Freed by task 477:
kasan_save_stack+0x1e/0x40
kasan_set_track+0x21/0x30
kasan_save_free_info+0x2a/0x50
__kasan_slab_free+0x10a/0x190
__kmem_cache_free+0xca/0x3f0
cifs_put_tcp_session+0x30c/0x450
cifs_mount+0xf95/0x1970
cifs_smb3_do_mount+0x295/0x1660
smb3_get_tree+0x352/0x5e0
vfs_get_tree+0x8e/0x2e0
path_mount+0xf8c/0x1990
do_mount+0xee/0x110
__x64_sys_mount+0x14b/0x1f0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
The buggy address belongs to the object at ffff888108f35380
which belongs to the cache kmalloc-16 of size 16
The buggy address is located 0 bytes inside of
16-byte region [ffff888108f35380, ffff888108f35390)
The buggy address belongs to the physical page:
page:00000000333f8e58 refcount:1 mapcount:0 mapping:0000000000000000 index:0xffff888108f350e0 pfn:0x108f35
flags: 0x200000000000200(slab|node=0|zone=2)
raw: 0200000000000200 0000000000000000 dead000000000122 ffff8881000423c0
raw: ffff888108f350e0 000000008080007a 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff888108f35280: fa fb fc fc fa fb fc fc fa fb fc fc fa fb fc fc
ffff888108f35300: fa fb fc fc fa fb fc fc fa fb fc fc fa fb fc fc
>ffff888108f35380: fa fb fc fc fa fb fc fc fa fb fc fc fa fb fc fc
^
ffff888108f35400: fa fb fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff888108f35480: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
Fixes: 7be3248f31 ("cifs: To match file servers, make sure the server hostname matches")
Signed-off-by: Zeng Heng <zengheng4@huawei.com>
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec5895c0f2 ]
Function mc146818_get_time() contains an elaborate mechanism of reading
the RTC time while no RTC update is in progress. It turns out that
reading the RTC alarm clock also requires avoiding the RTC update.
Therefore, the mechanism in mc146818_get_time() should be reused - so
extract it into a separate function.
The logic in mc146818_avoid_UIP() is same as in mc146818_get_time()
except that after every
if (CMOS_READ(RTC_FREQ_SELECT) & RTC_UIP) {
there is now "mdelay(1)".
To avoid producing a very unreadable patch, mc146818_get_time() will be
refactored to use mc146818_avoid_UIP() in the next patch.
Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211210200131.153887-6-mat.jonczyk@o2.pl
Stable-dep-of: cd17420ebe ("rtc: cmos: avoid UIP when writing alarm time")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8d3c106e19 upstream.
pagetable walks on address ranges mapped by VMAs can be done under the
mmap lock, the lock of an anon_vma attached to the VMA, or the lock of the
VMA's address_space. Only one of these needs to be held, and it does not
need to be held in exclusive mode.
Under those circumstances, the rules for concurrent access to page table
entries are:
- Terminal page table entries (entries that don't point to another page
table) can be arbitrarily changed under the page table lock, with the
exception that they always need to be consistent for
hardware page table walks and lockless_pages_from_mm().
This includes that they can be changed into non-terminal entries.
- Non-terminal page table entries (which point to another page table)
can not be modified; readers are allowed to READ_ONCE() an entry, verify
that it is non-terminal, and then assume that its value will stay as-is.
Retracting a page table involves modifying a non-terminal entry, so
page-table-level locks are insufficient to protect against concurrent page
table traversal; it requires taking all the higher-level locks under which
it is possible to start a page walk in the relevant range in exclusive
mode.
The collapse_huge_page() path for anonymous THP already follows this rule,
but the shmem/file THP path was getting it wrong, making it possible for
concurrent rmap-based operations to cause corruption.
Link: https://lkml.kernel.org/r/20221129154730.2274278-1-jannh@google.com
Link: https://lkml.kernel.org/r/20221128180252.1684965-1-jannh@google.com
Link: https://lkml.kernel.org/r/20221125213714.4115729-1-jannh@google.com
Fixes: 27e1f82731 ("khugepaged: enable collapse pmd for pte-mapped THP")
Signed-off-by: Jann Horn <jannh@google.com>
Reviewed-by: Yang Shi <shy828301@gmail.com>
Acked-by: David Hildenbrand <david@redhat.com>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[manual backport: this code was refactored from two copies into a common
helper between 5.15 and 6.0]
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a487069e11 ]
Add RmNet support for LARA-L6.
LARA-L6 module can be configured (by AT interface) in three different
USB modes:
* Default mode (Vendor ID: 0x1546 Product ID: 0x1341) with 4 serial
interfaces
* RmNet mode (Vendor ID: 0x1546 Product ID: 0x1342) with 4 serial
interfaces and 1 RmNet virtual network interface
* CDC-ECM mode (Vendor ID: 0x1546 Product ID: 0x1343) with 4 serial
interface and 1 CDC-ECM virtual network interface
In RmNet mode LARA-L6 exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parset/alternative functions
If 4: RMNET interface
Signed-off-by: Davide Tronchin <davide.tronchin.94@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3aa07f7289 ]
If there's a disconnection while operating in eSS, there may be a delay
in VBUS drop response from the connector. In that case, the internal
link state may drop to operate in usb2 speed while the controller thinks
the VBUS is still high. The driver must make sure to disable
GUSB2PHYCFG.SUSPHY when sending endpoint command while in usb2 speed.
The End Transfer command may be called, and only that command needs to
go through at this point. Let's keep it simple and unconditionally
disable GUSB2PHYCFG.SUSPHY whenever we issue the command.
This scenario is not seen in real hardware. In a rare case, our
prototype type-c controller/interface may have a slow response
triggerring this issue.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/5651117207803c26e2f22ddf4e5ce9e865dcf7c7.1668045468.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a11452a370 ]
When trying to see if we can clone a file range, there are cases where we
end up sending two write operations in case the inode from the source root
has an i_size that is not sector size aligned and the length from the
current offset to its i_size is less than the remaining length we are
trying to clone.
Issuing two write operations when we could instead issue a single write
operation is not incorrect. However it is not optimal, specially if the
extents are compressed and the flag BTRFS_SEND_FLAG_COMPRESSED was passed
to the send ioctl. In that case we can end up sending an encoded write
with an offset that is not sector size aligned, which makes the receiver
fallback to decompressing the data and writing it using regular buffered
IO (so re-compressing the data in case the fs is mounted with compression
enabled), because encoded writes fail with -EINVAL when an offset is not
sector size aligned.
The following example, which triggered a bug in the receiver code for the
fallback logic of decompressing + regular buffer IO and is fixed by the
patchset referred in a Link at the bottom of this changelog, is an example
where we have the non-optimal behaviour due to an unaligned encoded write:
$ cat test.sh
#!/bin/bash
DEV=/dev/sdj
MNT=/mnt/sdj
mkfs.btrfs -f $DEV > /dev/null
mount -o compress $DEV $MNT
# File foo has a size of 33K, not aligned to the sector size.
xfs_io -f -c "pwrite -S 0xab 0 33K" $MNT/foo
xfs_io -f -c "pwrite -S 0xcd 0 64K" $MNT/bar
# Now clone the first 32K of file bar into foo at offset 0.
xfs_io -c "reflink $MNT/bar 0 0 32K" $MNT/foo
# Snapshot the default subvolume and create a full send stream (v2).
btrfs subvolume snapshot -r $MNT $MNT/snap
btrfs send --compressed-data -f /tmp/test.send $MNT/snap
echo -e "\nFile bar in the original filesystem:"
od -A d -t x1 $MNT/snap/bar
umount $MNT
mkfs.btrfs -f $DEV > /dev/null
mount $DEV $MNT
echo -e "\nReceiving stream in a new filesystem..."
btrfs receive -f /tmp/test.send $MNT
echo -e "\nFile bar in the new filesystem:"
od -A d -t x1 $MNT/snap/bar
umount $MNT
Before this patch, the send stream included one regular write and one
encoded write for file 'bar', with the later being not sector size aligned
and causing the receiver to fallback to decompression + buffered writes.
The output of the btrfs receive command in verbose mode (-vvv):
(...)
mkfile o258-7-0
rename o258-7-0 -> bar
utimes
clone bar - source=foo source offset=0 offset=0 length=32768
write bar - offset=32768 length=1024
encoded_write bar - offset=33792, len=4096, unencoded_offset=33792, unencoded_file_len=31744, unencoded_len=65536, compression=1, encryption=0
encoded_write bar - falling back to decompress and write due to errno 22 ("Invalid argument")
(...)
This patch avoids the regular write followed by an unaligned encoded write
so that we end up sending a single encoded write that is aligned. So after
this patch the stream content is (output of btrfs receive -vvv):
(...)
mkfile o258-7-0
rename o258-7-0 -> bar
utimes
clone bar - source=foo source offset=0 offset=0 length=32768
encoded_write bar - offset=32768, len=4096, unencoded_offset=32768, unencoded_file_len=32768, unencoded_len=65536, compression=1, encryption=0
(...)
So we get more optimal behaviour and avoid the silent data loss bug in
versions of btrfs-progs affected by the bug referred by the Link tag
below (btrfs-progs v5.19, v5.19.1, v6.0 and v6.0.1).
Link: https://lore.kernel.org/linux-btrfs/cover.1668529099.git.fdmanana@suse.com/
Reviewed-by: Boris Burkov <boris@bur.io>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd5e1e4282 ]
The `nettest` binary, built from `selftests/net/nettest.c`,
was expected to be found in the path during test execution of
`fcnal-test.sh` and `pmtu.sh`, leading to tests getting
skipped when the binary is not installed in the system, as can
be seen in these logs found in the wild [1]:
# TEST: vti4: PMTU exceptions [SKIP]
[ 350.600250] IPv6: ADDRCONF(NETDEV_CHANGE): veth_b: link becomes ready
[ 350.607421] IPv6: ADDRCONF(NETDEV_CHANGE): veth_a: link becomes ready
# 'nettest' command not found; skipping tests
# xfrm6udp not supported
# TEST: vti6: PMTU exceptions (ESP-in-UDP) [SKIP]
[ 351.605102] IPv6: ADDRCONF(NETDEV_CHANGE): veth_b: link becomes ready
[ 351.612243] IPv6: ADDRCONF(NETDEV_CHANGE): veth_a: link becomes ready
# 'nettest' command not found; skipping tests
# xfrm4udp not supported
The `unicast_extensions.sh` tests also rely on `nettest`, but
it runs fine there because it looks for the binary in the
current working directory [2]:
The same mechanism that works for the Unicast extensions tests
is here copied over to the PMTU and functional tests.
[1] https://lkft.validation.linaro.org/scheduler/job/5839508#L6221
[2] https://lkft.validation.linaro.org/scheduler/job/5839508#L7958
Signed-off-by: Daniel Díaz <daniel.diaz@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05530ef7cf ]
With clang's kernel control flow integrity (kCFI, CONFIG_CFI_CLANG),
indirect call targets are validated against the expected function
pointer prototype to make sure the call target is valid to help mitigate
ROP attacks. If they are not identical, there is a failure at run time,
which manifests as either a kernel panic or thread getting killed.
seq_copy_in_user() and seq_copy_in_kernel() did not have prototypes
matching snd_seq_dump_func_t. Adjust this and remove the casts. There
are not resulting binary output differences.
This was found as a result of Clang's new -Wcast-function-type-strict
flag, which is more sensitive than the simpler -Wcast-function-type,
which only checks for type width mismatches.
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/lkml/202211041527.HD8TLSE1-lkp@intel.com
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Cc: alsa-devel@alsa-project.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20221118232346.never.380-kees@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7d7d4e7bb ]
Due to the hardware behavior, it takes some time for CBJ detection/impedance sensing/de-bounce.
The ClockStop_NotFinished flag will be raised until these functions are completed.
In ClockStopMode0 mode case, the SdW controller might check this flag from D3 to D0 when the
jack detection interrupt happened.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20221116090318.5017-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da74858a47 ]
The clock source and the sched_clock provided by the arm_global_timer
on Rockchip rk3066a/rk3188 are quite unstable because their rates
depend on the CPU frequency.
Recent changes to the arm_global_timer driver makes it impossible to use.
On the other side, the arm_global_timer has a higher rating than the
ROCKCHIP_TIMER, it will be selected by default by the time framework
while we want to use the stable Rockchip clock source.
Keep the arm_global_timer disabled in order to have the
DW_APB_TIMER (rk3066a) or ROCKCHIP_TIMER (rk3188) selected by default.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/f275ca8d-fd0a-26e5-b978-b7f3df815e0a@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ca507bf99 ]
DSPCLK_DIV field in WM8962_CLOCKING1 register is used to generate
correct frequency of LRCLK and BCLK. Sometimes the read-only value
can't be updated timely after enabling SYSCLK. This results in wrong
calculation values. Delay is introduced here to wait for newest value
from register. The time of the delay should be at least 500~1000us
according to test.
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221109121354.123958-1-chancel.liu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 340a982825 ]
Actually in no-MMU SoCs(i.e. i.MXRT) ZERO_PAGE(vaddr) expands to
```
virt_to_page(0)
```
that in order expands to:
```
pfn_to_page(virt_to_pfn(0))
```
and then virt_to_pfn(0) to:
```
((((unsigned long)(0) - PAGE_OFFSET) >> PAGE_SHIFT) +
PHYS_PFN_OFFSET)
```
where PAGE_OFFSET and PHYS_PFN_OFFSET are the DRAM offset(0x80000000) and
PAGE_SHIFT is 12. This way we obtain 16MB(0x01000000) summed to the base of
DRAM(0x80000000).
When ZERO_PAGE(0) is then used, for example in bio_add_page(), the page
gets an address that is out of DRAM bounds.
So instead of using fake virtual page 0 let's allocate a dedicated
zero_page during paging_init() and assign it to a global 'struct page *
empty_zero_page' the same way mmu.c does and it's the same approach used
in m68k with commit dc068f4621 as discussed here[0]. Then let's move
ZERO_PAGE() definition to the top of pgtable.h to be in common between
mmu.c and nommu.c.
[0]: https://lore.kernel.org/linux-m68k/2a462b23-5b8e-bbf4-ec7d-778434a3b9d7@google.com/T/#m1266ceb63
ad140743174d6b3070364d3c9a5179b
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ee47dcfff ]
We must prevent the CPU from reordering the files->count read with the
FD table access like this, on architectures where read-read reordering is
possible:
files_lookup_fd_raw()
close_fd()
put_files_struct()
atomic_read(&files->count)
I would like to mark this for stable, but the stable rules explicitly say
"no theoretical races", and given that the FD table pointer and
files->count are explicitly stored in the same cacheline, this sort of
reordering seems quite unlikely in practice...
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Add support for the Crystalfontz CFA050-PI-M series of Raspberry Pi
CM4-based modules using the CFAF7201280A0_050Tx TFT LCD displays.
Signed-off-by: Mark Williams <mwp@mwp.id.au>
commit bce9332220 upstream.
proc_skip_spaces() seems to think it is working on C strings, and ends
up being just a wrapper around skip_spaces() with a really odd calling
convention.
Instead of basing it on skip_spaces(), it should have looked more like
proc_skip_char(), which really is the exact same function (except it
skips a particular character, rather than whitespace). So use that as
inspiration, odd coding and all.
Now the calling convention actually makes sense and works for the
intended purpose.
Reported-and-tested-by: Kyle Zeng <zengyhkyle@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e6cfaf34be upstream.
proc_get_long() is passed a size_t, but then assigns it to an 'int'
variable for the length. Let's not do that, even if our IO paths are
limited to MAX_RW_COUNT (exactly because of these kinds of type errors).
So do the proper test in the rigth type.
Reported-by: Kyle Zeng <zengyhkyle@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b52be557e2 upstream.
When __do_semtimedop() goes to sleep because it has to wait for a
semaphore value becoming zero or becoming bigger than some threshold, it
links the on-stack sem_queue to the sem_array, then goes to sleep
without holding a reference on the sem_array.
When __do_semtimedop() comes back out of sleep, one of two things must
happen:
a) We prove that the on-stack sem_queue has been disconnected from the
(possibly freed) sem_array, making it safe to return from the stack
frame that the sem_queue exists in.
b) We stabilize our reference to the sem_array, lock the sem_array, and
detach the sem_queue from the sem_array ourselves.
sem_array has RCU lifetime, so for case (b), the reference can be
stabilized inside an RCU read-side critical section by locklessly
checking whether the sem_queue is still connected to the sem_array.
However, the current code does the lockless check on sem_queue before
starting an RCU read-side critical section, so the result of the
lockless check immediately becomes useless.
Fix it by doing rcu_read_lock() before the lockless check. Now RCU
ensures that if we observe the object being on our queue, the object
can't be freed until rcu_read_unlock().
This bug is only hittable on kernel builds with full preemption support
(either CONFIG_PREEMPT or PREEMPT_DYNAMIC with preempt=full).
Fixes: 370b262c89 ("ipc/sem: avoid idr tree lookup for interrupted semop")
Cc: stable@vger.kernel.org
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23393c6461 upstream.
Currently tpm transactions are executed unconditionally in
tpm_pm_suspend() function, which may lead to races with other tpm
accessors in the system.
Specifically, the hw_random tpm driver makes use of tpm_get_random(),
and this function is called in a loop from a kthread, which means it's
not frozen alongside userspace, and so can race with the work done
during system suspend:
tpm tpm0: tpm_transmit: tpm_recv: error -52
tpm tpm0: invalid TPM_STS.x 0xff, dumping stack for forensics
CPU: 0 PID: 1 Comm: init Not tainted 6.1.0-rc5+ #135
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.0-20220807_005459-localhost 04/01/2014
Call Trace:
tpm_tis_status.cold+0x19/0x20
tpm_transmit+0x13b/0x390
tpm_transmit_cmd+0x20/0x80
tpm1_pm_suspend+0xa6/0x110
tpm_pm_suspend+0x53/0x80
__pnp_bus_suspend+0x35/0xe0
__device_suspend+0x10f/0x350
Fix this by calling tpm_try_get_ops(), which itself is a wrapper around
tpm_chip_start(), but takes the appropriate mutex.
Signed-off-by: Jan Dabros <jsd@semihalf.com>
Reported-by: Vlastimil Babka <vbabka@suse.cz>
Tested-by: Jason A. Donenfeld <Jason@zx2c4.com>
Tested-by: Vlastimil Babka <vbabka@suse.cz>
Link: https://lore.kernel.org/all/c5ba47ef-393f-1fba-30bd-1230d1b4b592@suse.cz/
Cc: stable@vger.kernel.org
Fixes: e891db1a18 ("tpm: turn on TPM on suspend for TPM 1.x")
[Jason: reworked commit message, added metadata]
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d9f15a9de4 ]
This reverts commit 232ccac1bd.
On the subject of suspend, the RISC-V SBI spec states:
This does not cover whether any given events actually reach the hart or
not, just what the hart will do if it receives an event. On PolarFire
SoC, and potentially other SiFive based implementations, events from the
RISC-V timer do reach a hart during suspend. This is not the case for the
implementation on the Allwinner D1 - there timer events are not received
during suspend.
To fix this, the CLOCK_EVT_FEAT_C3STOP (mis)feature was enabled for the
timer driver - but this has broken both RCU stall detection and timers
generally on PolarFire SoC and potentially other SiFive based
implementations.
If an AXI read to the PCIe controller on PolarFire SoC times out, the
system will stall, however, with CLOCK_EVT_FEAT_C3STOP active, the system
just locks up without RCU stalling:
io scheduler mq-deadline registered
io scheduler kyber registered
microchip-pcie 2000000000.pcie: host bridge /soc/pcie@2000000000 ranges:
microchip-pcie 2000000000.pcie: MEM 0x2008000000..0x2087ffffff -> 0x0008000000
microchip-pcie 2000000000.pcie: sec error in pcie2axi buffer
microchip-pcie 2000000000.pcie: ded error in pcie2axi buffer
microchip-pcie 2000000000.pcie: axi read request error
microchip-pcie 2000000000.pcie: axi read timeout
microchip-pcie 2000000000.pcie: sec error in pcie2axi buffer
microchip-pcie 2000000000.pcie: ded error in pcie2axi buffer
microchip-pcie 2000000000.pcie: sec error in pcie2axi buffer
microchip-pcie 2000000000.pcie: ded error in pcie2axi buffer
microchip-pcie 2000000000.pcie: sec error in pcie2axi buffer
microchip-pcie 2000000000.pcie: ded error in pcie2axi buffer
Freeing initrd memory: 7332K
Similarly issues were reported with clock_nanosleep() - with a test app
that sleeps each cpu for 6, 5, 4, 3 ms respectively, HZ=250 & the blamed
commit in place, the sleep times are rounded up to the next jiffy:
== CPU: 1 == == CPU: 2 == == CPU: 3 == == CPU: 4 ==
Mean: 7.974992 Mean: 7.976534 Mean: 7.962591 Mean: 3.952179
Std Dev: 0.154374 Std Dev: 0.156082 Std Dev: 0.171018 Std Dev: 0.076193
Hi: 9.472000 Hi: 10.495000 Hi: 8.864000 Hi: 4.736000
Lo: 6.087000 Lo: 6.380000 Lo: 4.872000 Lo: 3.403000
Samples: 521 Samples: 521 Samples: 521 Samples: 521
Fortunately, the D1 has a second timer, which is "currently used in
preference to the RISC-V/SBI timer driver" so a revert here does not
hurt operation of D1 in its current form.
Ultimately, a DeviceTree property (or node) will be added to encode the
behaviour of the timers, but until then revert the addition of
CLOCK_EVT_FEAT_C3STOP.
Fixes: 232ccac1bd ("clocksource/drivers/riscv: Events are stopped during CPU suspend")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Palmer Dabbelt <palmer@rivosinc.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Acked-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/linux-riscv/YzYTNQRxLr7Q9JR0@spud/
Link: https://github.com/riscv-non-isa/riscv-sbi-doc/issues/98/
Link: https://lore.kernel.org/linux-riscv/bf6d3b1f-f703-4a25-833e-972a44a04114@sholland.org/
Link: https://lore.kernel.org/r/20221122121620.3522431-1-conor.dooley@microchip.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 48d4180939 ]
In a system with a single initiator node, and one or more memory-only
'target' nodes, the memory-only node(s) would fail to register their
initiator node correctly. i.e. in sysfs:
# ls /sys/devices/system/node/node0/access0/targets/
node0
Where as the correct behavior should be:
# ls /sys/devices/system/node/node0/access0/targets/
node0 node1
This happened because hmat_register_target_initiators() uses list_sort()
to sort the initiator list, but the sort comparision function
(initiator_cmp()) is overloaded to also set the node mask's bits.
In a system with a single initiator, the list is singular, and list_sort
elides the comparision helper call. Thus the node mask never gets set,
and the subsequent search for the best initiator comes up empty.
Add a new helper to consume the sorted initiator list, and generate the
nodemask, decoupling it from the overloaded initiator_cmp() comparision
callback. This prevents the singular list corner case naturally, and
makes the code easier to follow as well.
Cc: <stable@vger.kernel.org>
Cc: Rafael J. Wysocki <rafael@kernel.org>
Cc: Liu Shixin <liushixin2@huawei.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: Chris Piper <chris.d.piper@intel.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Link: https://lore.kernel.org/r/20221116-acpi_hmat_fix-v2-2-3712569be691@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d36678f790 ]
Recent changes to the DMA code has resulting in the IMX driver failing
I2C transfers when the buffer has been vmalloc. Only perform DMA
transfers if the message has the I2C_M_DMA_SAFE flag set, indicating
the client is providing a buffer which is DMA safe.
This is a minimal fix for stable. The I2C core provides helpers to
allocate a bounce buffer. For a fuller fix the master should make use
of these helpers.
Fixes: 4544b9f25e ("dma-mapping: Add vmap checks to dma_map_single()")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 145900cf91 ]
A problem about i2c-npcm7xx create debugfs failed is triggered with the
following log given:
[ 173.827310] debugfs: Directory 'npcm_i2c' with parent '/' already present!
The reason is that npcm_i2c_init() returns platform_driver_register()
directly without checking its return value, if platform_driver_register()
failed, it returns without destroy the newly created debugfs, resulting
the debugfs of npcm_i2c can never be created later.
npcm_i2c_init()
debugfs_create_dir() # create debugfs directory
platform_driver_register()
driver_register()
bus_add_driver()
priv = kzalloc(...) # OOM happened
# return without destroy debugfs directory
Fix by removing debugfs when platform_driver_register() returns error.
Fixes: 56a1485b10 ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Reviewed-by: Tali Perry <tali.perry@nuvoton.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit adafbbf689 ]
The STM32 USART can control RS-485 Transmit Enable in hardware. Since
commit 7df5081cbf ("serial: stm32: Add RS485 RTS GPIO control"),
it can alternatively be controlled in software. That was done to allow
RS-485 even if the RTS pin is unavailable because it's pinmuxed to a
different function.
However the commit neglected to deassert Transmit Enable upon invocation
of the ->rs485_config() callback. Fix it.
Avoid forward declarations by moving stm32_usart_tx_empty(),
stm32_usart_rs485_rts_enable() and stm32_usart_rs485_rts_disable()
further up in the driver.
Fixes: 7df5081cbf ("serial: stm32: Add RS485 RTS GPIO control")
Cc: stable@vger.kernel.org # v5.9+
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/6059eab35dba394468335ef640df8b0050fd9dbd.1662886616.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5082d386e ]
When the kernel receives a route deletion request from user space it
tries to delete a route that matches the route attributes specified in
the request.
If only prefix information is specified in the request, the kernel
should delete the first matching FIB alias regardless of its associated
FIB info. However, an error is currently returned when the FIB info is
backed by a nexthop object:
# ip nexthop add id 1 via 192.0.2.2 dev dummy10
# ip route add 198.51.100.0/24 nhid 1
# ip route del 198.51.100.0/24
RTNETLINK answers: No such process
Fix by matching on such a FIB info when legacy nexthop attributes are
not specified in the request. An earlier check already covers the case
where a nexthop ID is specified in the request.
Add tests that cover these flows. Before the fix:
# ./fib_nexthops.sh -t ipv4_fcnal
...
TEST: Delete route when not specifying nexthop attributes [FAIL]
Tests passed: 11
Tests failed: 1
After the fix:
# ./fib_nexthops.sh -t ipv4_fcnal
...
TEST: Delete route when not specifying nexthop attributes [ OK ]
Tests passed: 12
Tests failed: 0
No regressions in other tests:
# ./fib_nexthops.sh
...
Tests passed: 228
Tests failed: 0
# ./fib_tests.sh
...
Tests passed: 186
Tests failed: 0
Cc: stable@vger.kernel.org
Reported-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Jonas Gorski <jonas.gorski@gmail.com>
Fixes: 493ced1ac4 ("ipv4: Allow routes to use nexthop objects")
Fixes: 6bf92d70e6 ("net: ipv4: fix route with nexthop object delete warning")
Fixes: 61b91eb33a ("ipv4: Handle attempt to delete multipath route when fib_info contains an nh reference")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20221124210932.2470010-1-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61b91eb33a ]
Gwangun Jung reported a slab-out-of-bounds access in fib_nh_match:
fib_nh_match+0xf98/0x1130 linux-6.0-rc7/net/ipv4/fib_semantics.c:961
fib_table_delete+0x5f3/0xa40 linux-6.0-rc7/net/ipv4/fib_trie.c:1753
inet_rtm_delroute+0x2b3/0x380 linux-6.0-rc7/net/ipv4/fib_frontend.c:874
Separate nexthop objects are mutually exclusive with the legacy
multipath spec. Fix fib_nh_match to return if the config for the
to be deleted route contains a multipath spec while the fib_info
is using a nexthop object.
Fixes: 493ced1ac4 ("ipv4: Allow routes to use nexthop objects")
Fixes: 6bf92d70e6 ("net: ipv4: fix route with nexthop object delete warning")
Reported-by: Gwangun Jung <exsociety@gmail.com>
Signed-off-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: d5082d386e ("ipv4: Fix route deletion when nexthop info is not specified")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 692930cc43 ]
I made a stupid typo when adding the nexthop route warning selftest and
added both $IP and ip after it (double ip) on the cleanup path. The
error doesn't show up when running the test, but obviously it doesn't
cleanup properly after it.
Fixes: 392baa339c ("selftests: net: add delete nexthop route warning test")
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: d5082d386e ("ipv4: Fix route deletion when nexthop info is not specified")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 392baa339c ]
Add a test which causes a WARNING on kernels which treat a
nexthop route like a normal route when comparing for deletion and a
device is specified. That is, a route is found but we hit a warning while
matching it. The warning is from fib_info_nh() in include/net/nexthop.h
because we run it on a fib_info with nexthop object. The call chain is:
inet_rtm_delroute -> fib_table_delete -> fib_nh_match (called with a
nexthop fib_info and also with fc_oif set thus calling fib_info_nh on
the fib_info and triggering the warning).
Repro steps:
$ ip nexthop add id 12 via 172.16.1.3 dev veth1
$ ip route add 172.16.101.1/32 nhid 12
$ ip route delete 172.16.101.1/32 dev veth1
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: d5082d386e ("ipv4: Fix route deletion when nexthop info is not specified")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d192bec53 ]
PA-RISC uses a much bigger frame size for functions than other
architectures. So increase it to 2048 for 32- and 64-bit kernels.
This fixes e.g. a warning in lib/xxhash.c.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Stable-dep-of: 152fe65f30 ("Kconfig.debug: provide a little extra FRAME_WARN leeway when KASAN is enabled")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 829ae0f81c ]
The issue is reported when removing memory through virtio_mem device. The
transparent huge page, experienced copy-on-write fault, is wrongly
regarded as pinned. The transparent huge page is escaped from being
isolated in isolate_migratepages_block(). The transparent huge page can't
be migrated and the corresponding memory block can't be put into offline
state.
Fix it by replacing page_mapcount() with total_mapcount(). With this, the
transparent huge page can be isolated and migrated, and the memory block
can be put into offline state. Besides, The page's refcount is increased
a bit earlier to avoid the page is released when the check is executed.
Link: https://lkml.kernel.org/r/20221124095523.31061-1-gshan@redhat.com
Fixes: 1da2f328fa ("mm,thp,compaction,cma: allow THP migration for CMA allocations")
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reported-by: Zhenyu Zhang <zhenyzha@redhat.com>
Tested-by: Zhenyu Zhang <zhenyzha@redhat.com>
Suggested-by: David Hildenbrand <david@redhat.com>
Acked-by: David Hildenbrand <david@redhat.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: William Kucharski <william.kucharski@oracle.com>
Cc: Zi Yan <ziy@nvidia.com>
Cc: <stable@vger.kernel.org> [5.7+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89f6c88a6a ]
__isolate_lru_page_prepare() conflates two unrelated functions, with the
flags to one disjoint from the flags to the other; and hides some of the
important checks outside of isolate_migratepages_block(), where the
sequence is better to be visible. It comes from the days of lumpy
reclaim, before compaction, when the combination made more sense.
Move what's needed by mm/compaction.c isolate_migratepages_block() inline
there, and what's needed by mm/vmscan.c isolate_lru_pages() inline there.
Shorten "isolate_mode" to "mode", so the sequence of conditions is easier
to read. Declare a "mapping" variable, to save one call to page_mapping()
(but not another: calling again after page is locked is necessary).
Simplify isolate_lru_pages() with a "move_to" list pointer.
Link: https://lkml.kernel.org/r/879d62a8-91cc-d3c6-fb3b-69768236df68@google.com
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: David Rientjes <rientjes@google.com>
Reviewed-by: Alex Shi <alexs@kernel.org>
Cc: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stable-dep-of: 829ae0f81c ("mm: migrate: fix THP's mapcount on isolation")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4bedbbd782 ]
for_each_pci_dev() is implemented by pci_get_device(). The comment of
pci_get_device() says that it will increase the reference count for the
returned pci_dev and also decrease the reference count for the input
pci_dev @from if it is not NULL.
If we break for_each_pci_dev() loop with pdev not NULL, we need to call
pci_dev_put() to decrease the reference count. Add the missing
pci_dev_put() for the error path to avoid reference count leak.
Fixes: 2e45528930 ("iommu/vt-d: Unify the way to process DMAR device scope array")
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Link: https://lore.kernel.org/r/20221121113649.190393-3-wangxiongfeng2@huawei.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit afca9e19cc ]
for_each_pci_dev() is implemented by pci_get_device(). The comment of
pci_get_device() says that it will increase the reference count for the
returned pci_dev and also decrease the reference count for the input
pci_dev @from if it is not NULL.
If we break for_each_pci_dev() loop with pdev not NULL, we need to call
pci_dev_put() to decrease the reference count. Add the missing
pci_dev_put() before 'return true' to avoid reference count leak.
Fixes: 89a6079df7 ("iommu/vt-d: Force IOMMU on for platform opt in hint")
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Link: https://lore.kernel.org/r/20221121113649.190393-2-wangxiongfeng2@huawei.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e1864332f ]
Currently, when detecting vmap stack overflow, riscv firstly switches
to the so called shadow stack, then use this shadow stack to call the
get_overflow_stack() to get the overflow stack. However, there's
a race here if two or more harts use the same shadow stack at the same
time.
To solve this race, we introduce spin_shadow_stack atomic var, which
will be swap between its own address and 0 in atomic way, when the
var is set, it means the shadow_stack is being used; when the var
is cleared, it means the shadow_stack isn't being used.
Fixes: 31da94c25a ("riscv: add VMAP_STACK overflow detection")
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Suggested-by: Guo Ren <guoren@kernel.org>
Reviewed-by: Guo Ren <guoren@kernel.org>
Link: https://lore.kernel.org/r/20221030124517.2370-1-jszhang@kernel.org
[Palmer: Add AQ to the swap, and also some comments.]
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f105a7427 ]
The EFI page table is initially created as a copy of the kernel page table.
With VMAP_STACK enabled, kernel stacks are allocated in the vmalloc area:
if the stack is allocated in a new PGD (one that was not present at the
moment of the efi page table creation or not synced in a previous vmalloc
fault), the kernel will take a trap when switching to the efi page table
when the vmalloc kernel stack is accessed, resulting in a kernel panic.
Fix that by updating the efi kernel mappings before switching to the efi
page table.
Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Fixes: b91540d52a ("RISC-V: Add EFI runtime services")
Tested-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Link: https://lore.kernel.org/r/20221121133303.1782246-1-alexghiti@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 64c150339e ]
There is a possibility of dividing by zero due to the pcs->bits_per_pin
if pcs->fmask() also has a value of zero and called fls
from asm-generic/bitops/builtin-fls.h or arch/x86/include/asm/bitops.h.
The function pcs_probe() has the branch that assigned to fmask 0 before
pcs_allocate_pin_table() was called
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 4e7e8017a8 ("pinctrl: pinctrl-single: enhance to configure multiple pins of different modules")
Signed-off-by: Maxim Korotkov <korotkov.maxim.s@gmail.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20221117123034.27383-1-korotkov.maxim.s@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 47b0c2e4c2 upstream.
make_mmu_pages_available() must be called with mmu_lock held for write.
However, if the TDP MMU is used, it will be called with mmu_lock held for
read.
This function does nothing unless shadow pages are used, so there is no
race unless nested TDP is used.
Since nested TDP uses shadow pages, old shadow pages may be zapped by this
function even when the TDP MMU is enabled.
Since shadow pages are never allocated by kvm_tdp_mmu_map(), a race
condition can be avoided by not calling make_mmu_pages_available() if the
TDP MMU is currently in use.
I encountered this when repeatedly starting and stopping nested VM.
It can be artificially caused by allocating a large number of nested TDP
SPTEs.
For example, the following BUG and general protection fault are caused in
the host kernel.
pte_list_remove: 00000000cd54fc10 many->many
------------[ cut here ]------------
kernel BUG at arch/x86/kvm/mmu/mmu.c:963!
invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
RIP: 0010:pte_list_remove.cold+0x16/0x48 [kvm]
Call Trace:
<TASK>
drop_spte+0xe0/0x180 [kvm]
mmu_page_zap_pte+0x4f/0x140 [kvm]
__kvm_mmu_prepare_zap_page+0x62/0x3e0 [kvm]
kvm_mmu_zap_oldest_mmu_pages+0x7d/0xf0 [kvm]
direct_page_fault+0x3cb/0x9b0 [kvm]
kvm_tdp_page_fault+0x2c/0xa0 [kvm]
kvm_mmu_page_fault+0x207/0x930 [kvm]
npf_interception+0x47/0xb0 [kvm_amd]
svm_invoke_exit_handler+0x13c/0x1a0 [kvm_amd]
svm_handle_exit+0xfc/0x2c0 [kvm_amd]
kvm_arch_vcpu_ioctl_run+0xa79/0x1780 [kvm]
kvm_vcpu_ioctl+0x29b/0x6f0 [kvm]
__x64_sys_ioctl+0x95/0xd0
do_syscall_64+0x5c/0x90
general protection fault, probably for non-canonical address
0xdead000000000122: 0000 [#1] PREEMPT SMP NOPTI
RIP: 0010:kvm_mmu_commit_zap_page.part.0+0x4b/0xe0 [kvm]
Call Trace:
<TASK>
kvm_mmu_zap_oldest_mmu_pages+0xae/0xf0 [kvm]
direct_page_fault+0x3cb/0x9b0 [kvm]
kvm_tdp_page_fault+0x2c/0xa0 [kvm]
kvm_mmu_page_fault+0x207/0x930 [kvm]
npf_interception+0x47/0xb0 [kvm_amd]
CVE: CVE-2022-45869
Fixes: a2855afc7e ("KVM: x86/mmu: Allow parallel page faults for the TDP MMU")
Signed-off-by: Kazuki Takiguchi <takiguchi.kazuki171@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ upstream commit 12ad3d2d6c ]
There is an interesting race condition of poll_refs which could result
in a NULL pointer dereference. The crash trace is like:
KASAN: null-ptr-deref in range [0x0000000000000008-0x000000000000000f]
CPU: 0 PID: 30781 Comm: syz-executor.2 Not tainted 6.0.0-g493ffd6605b2 #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
1.13.0-1ubuntu1.1 04/01/2014
RIP: 0010:io_poll_remove_entry io_uring/poll.c:154 [inline]
RIP: 0010:io_poll_remove_entries+0x171/0x5b4 io_uring/poll.c:190
Code: ...
RSP: 0018:ffff88810dfefba0 EFLAGS: 00010202
RAX: 0000000000000001 RBX: 0000000000000000 RCX: 0000000000040000
RDX: ffffc900030c4000 RSI: 000000000003ffff RDI: 0000000000040000
RBP: 0000000000000008 R08: ffffffff9764d3dd R09: fffffbfff3836781
R10: fffffbfff3836781 R11: 0000000000000000 R12: 1ffff11003422d60
R13: ffff88801a116b04 R14: ffff88801a116ac0 R15: dffffc0000000000
FS: 00007f9c07497700(0000) GS:ffff88811a600000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007ffb5c00ea98 CR3: 0000000105680005 CR4: 0000000000770ef0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
<TASK>
io_apoll_task_func+0x3f/0xa0 io_uring/poll.c:299
handle_tw_list io_uring/io_uring.c:1037 [inline]
tctx_task_work+0x37e/0x4f0 io_uring/io_uring.c:1090
task_work_run+0x13a/0x1b0 kernel/task_work.c:177
get_signal+0x2402/0x25a0 kernel/signal.c:2635
arch_do_signal_or_restart+0x3b/0x660 arch/x86/kernel/signal.c:869
exit_to_user_mode_loop kernel/entry/common.c:166 [inline]
exit_to_user_mode_prepare+0xc2/0x160 kernel/entry/common.c:201
__syscall_exit_to_user_mode_work kernel/entry/common.c:283 [inline]
syscall_exit_to_user_mode+0x58/0x160 kernel/entry/common.c:294
entry_SYSCALL_64_after_hwframe+0x63/0xcd
The root cause for this is a tiny overlooking in
io_poll_check_events() when cocurrently run with poll cancel routine
io_poll_cancel_req().
The interleaving to trigger use-after-free:
CPU0 | CPU1
|
io_apoll_task_func() | io_poll_cancel_req()
io_poll_check_events() |
// do while first loop |
v = atomic_read(...) |
// v = poll_refs = 1 |
... | io_poll_mark_cancelled()
| atomic_or()
| // poll_refs =
IO_POLL_CANCEL_FLAG | 1
|
atomic_sub_return(...) |
// poll_refs = IO_POLL_CANCEL_FLAG |
// loop continue |
|
| io_poll_execute()
| io_poll_get_ownership()
| // poll_refs =
IO_POLL_CANCEL_FLAG | 1
| // gets the ownership
v = atomic_read(...) |
// poll_refs not change |
|
if (v & IO_POLL_CANCEL_FLAG) |
return -ECANCELED; |
// io_poll_check_events return |
// will go into |
// io_req_complete_failed() free req |
|
| io_apoll_task_func()
| // also go into
io_req_complete_failed()
And the interleaving to trigger the kernel WARNING:
CPU0 | CPU1
|
io_apoll_task_func() | io_poll_cancel_req()
io_poll_check_events() |
// do while first loop |
v = atomic_read(...) |
// v = poll_refs = 1 |
... | io_poll_mark_cancelled()
| atomic_or()
| // poll_refs =
IO_POLL_CANCEL_FLAG | 1
|
atomic_sub_return(...) |
// poll_refs = IO_POLL_CANCEL_FLAG |
// loop continue |
|
v = atomic_read(...) |
// v = IO_POLL_CANCEL_FLAG |
| io_poll_execute()
| io_poll_get_ownership()
| // poll_refs =
IO_POLL_CANCEL_FLAG | 1
| // gets the ownership
|
WARN_ON_ONCE(!(v & IO_POLL_REF_MASK))) |
// v & IO_POLL_REF_MASK = 0 WARN |
|
| io_apoll_task_func()
| // also go into
io_req_complete_failed()
By looking up the source code and communicating with Pavel, the
implementation of this atomic poll refs should continue the loop of
io_poll_check_events() just to avoid somewhere else to grab the
ownership. Therefore, this patch simply adds another AND operation to
make sure the loop will stop if it finds the poll_refs is exactly equal
to IO_POLL_CANCEL_FLAG. Since io_poll_cancel_req() grabs ownership and
will finally make its way to io_req_complete_failed(), the req will
be reclaimed as expected.
Fixes: aa43477b04 ("io_uring: poll rework")
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Reviewed-by: Pavel Begunkov <asml.silence@gmail.com>
[axboe: tweak description and code style]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ upstream commit a26a35e901 ]
poll_refs carry two functions, the first is ownership over the request.
The second is notifying the io_poll_check_events() that there was an
event but wake up couldn't grab the ownership, so io_poll_check_events()
should retry.
We want to make poll_refs more robust against overflows. Instead of
always incrementing it, which covers two purposes with one atomic, check
if poll_refs is elevated enough and if so set a retry flag without
attempts to grab ownership. The gap between the bias check and following
atomics may seem racy, but we don't need it to be strict. Moreover there
might only be maximum 4 parallel updates: by the first and the second
poll entries, __io_arm_poll_handler() and cancellation. From those four,
only poll wake ups may be executed multiple times, but they're protected
by a spin.
Cc: stable@vger.kernel.org
Reported-by: Lin Ma <linma@zju.edu.cn>
Fixes: aa43477b04 ("io_uring: poll rework")
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/c762bc31f8683b3270f3587691348a7119ef9c9d.1668963050.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ upstream commit 2f3893437a ]
Replace atomically substracting the ownership reference at the end of
arming a poll with a cmpxchg. We try to release ownership by setting 0
assuming that poll_refs didn't change while we were arming. If it did
change, we keep the ownership and use it to queue a tw, which is fully
capable to process all events and (even tolerates spurious wake ups).
It's a bit more elegant as we reduce races b/w setting the cancellation
flag and getting refs with this release, and with that we don't have to
worry about any kinds of underflows. It's not the fastest path for
polling. The performance difference b/w cmpxchg and atomic dec is
usually negligible and it's not the fastest path.
Cc: stable@vger.kernel.org
Fixes: aa43477b04 ("io_uring: poll rework")
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/0c95251624397ea6def568ff040cad2d7926fd51.1668963050.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4313e5a613 upstream.
After 65536 dynamic events have been added and removed, the "type" field
of the event then uses the first type number that is available (not
currently used by other events). A type number is the identifier of the
binary blobs in the tracing ring buffer (known as events) to map them to
logic that can parse the binary blob.
The issue is that if a dynamic event (like a kprobe event) is traced and
is in the ring buffer, and then that event is removed (because it is
dynamic, which means it can be created and destroyed), if another dynamic
event is created that has the same number that new event's logic on
parsing the binary blob will be used.
To show how this can be an issue, the following can crash the kernel:
# cd /sys/kernel/tracing
# for i in `seq 65536`; do
echo 'p:kprobes/foo do_sys_openat2 $arg1:u32' > kprobe_events
# done
For every iteration of the above, the writing to the kprobe_events will
remove the old event and create a new one (with the same format) and
increase the type number to the next available on until the type number
reaches over 65535 which is the max number for the 16 bit type. After it
reaches that number, the logic to allocate a new number simply looks for
the next available number. When an dynamic event is removed, that number
is then available to be reused by the next dynamic event created. That is,
once the above reaches the max number, the number assigned to the event in
that loop will remain the same.
Now that means deleting one dynamic event and created another will reuse
the previous events type number. This is where bad things can happen.
After the above loop finishes, the kprobes/foo event which reads the
do_sys_openat2 function call's first parameter as an integer.
# echo 1 > kprobes/foo/enable
# cat /etc/passwd > /dev/null
# cat trace
cat-2211 [005] .... 2007.849603: foo: (do_sys_openat2+0x0/0x130) arg1=4294967196
cat-2211 [005] .... 2007.849620: foo: (do_sys_openat2+0x0/0x130) arg1=4294967196
cat-2211 [005] .... 2007.849838: foo: (do_sys_openat2+0x0/0x130) arg1=4294967196
cat-2211 [005] .... 2007.849880: foo: (do_sys_openat2+0x0/0x130) arg1=4294967196
# echo 0 > kprobes/foo/enable
Now if we delete the kprobe and create a new one that reads a string:
# echo 'p:kprobes/foo do_sys_openat2 +0($arg2):string' > kprobe_events
And now we can the trace:
# cat trace
sendmail-1942 [002] ..... 530.136320: foo: (do_sys_openat2+0x0/0x240) arg1= cat-2046 [004] ..... 530.930817: foo: (do_sys_openat2+0x0/0x240) arg1="������������������������������������������������������������������������������������������������"
cat-2046 [004] ..... 530.930961: foo: (do_sys_openat2+0x0/0x240) arg1="������������������������������������������������������������������������������������������������"
cat-2046 [004] ..... 530.934278: foo: (do_sys_openat2+0x0/0x240) arg1="������������������������������������������������������������������������������������������������"
cat-2046 [004] ..... 530.934563: foo: (do_sys_openat2+0x0/0x240) arg1="������������������������������������������������������������������������������������������������"
bash-1515 [007] ..... 534.299093: foo: (do_sys_openat2+0x0/0x240) arg1="kkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkk���������@��4Z����;Y�����U
And dmesg has:
==================================================================
BUG: KASAN: use-after-free in string+0xd4/0x1c0
Read of size 1 at addr ffff88805fdbbfa0 by task cat/2049
CPU: 0 PID: 2049 Comm: cat Not tainted 6.1.0-rc6-test+ #641
Hardware name: Hewlett-Packard HP Compaq Pro 6300 SFF/339A, BIOS K01 v03.03 07/14/2016
Call Trace:
<TASK>
dump_stack_lvl+0x5b/0x77
print_report+0x17f/0x47b
kasan_report+0xad/0x130
string+0xd4/0x1c0
vsnprintf+0x500/0x840
seq_buf_vprintf+0x62/0xc0
trace_seq_printf+0x10e/0x1e0
print_type_string+0x90/0xa0
print_kprobe_event+0x16b/0x290
print_trace_line+0x451/0x8e0
s_show+0x72/0x1f0
seq_read_iter+0x58e/0x750
seq_read+0x115/0x160
vfs_read+0x11d/0x460
ksys_read+0xa9/0x130
do_syscall_64+0x3a/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
RIP: 0033:0x7fc2e972ade2
Code: c0 e9 b2 fe ff ff 50 48 8d 3d b2 3f 0a 00 e8 05 f0 01 00 0f 1f 44 00 00 f3 0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 0f 05 <48> 3d 00 f0 ff ff 77 56 c3 0f 1f 44 00 00 48 83 ec 28 48 89 54 24
RSP: 002b:00007ffc64e687c8 EFLAGS: 00000246 ORIG_RAX: 0000000000000000
RAX: ffffffffffffffda RBX: 0000000000020000 RCX: 00007fc2e972ade2
RDX: 0000000000020000 RSI: 00007fc2e980d000 RDI: 0000000000000003
RBP: 00007fc2e980d000 R08: 00007fc2e980c010 R09: 0000000000000000
R10: 0000000000000022 R11: 0000000000000246 R12: 0000000000020f00
R13: 0000000000000003 R14: 0000000000020000 R15: 0000000000020000
</TASK>
The buggy address belongs to the physical page:
page:ffffea00017f6ec0 refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x5fdbb
flags: 0xfffffc0000000(node=0|zone=1|lastcpupid=0x1fffff)
raw: 000fffffc0000000 0000000000000000 ffffea00017f6ec8 0000000000000000
raw: 0000000000000000 0000000000000000 00000000ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff88805fdbbe80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ffff88805fdbbf00: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
>ffff88805fdbbf80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
^
ffff88805fdbc000: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ffff88805fdbc080: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
==================================================================
This was found when Zheng Yejian sent a patch to convert the event type
number assignment to use IDA, which gives the next available number, and
this bug showed up in the fuzz testing by Yujie Liu and the kernel test
robot. But after further analysis, I found that this behavior is the same
as when the event type numbers go past the 16bit max (and the above shows
that).
As modules have a similar issue, but is dealt with by setting a
"WAS_ENABLED" flag when a module event is enabled, and when the module is
freed, if any of its events were enabled, the ring buffer that holds that
event is also cleared, to prevent reading stale events. The same can be
done for dynamic events.
If any dynamic event that is being removed was enabled, then make sure the
buffers they were enabled in are now cleared.
Link: https://lkml.kernel.org/r/20221123171434.545706e3@gandalf.local.home
Link: https://lore.kernel.org/all/20221110020319.1259291-1-zhengyejian1@huawei.com/
Cc: stable@vger.kernel.org
Cc: Andrew Morton <akpm@linux-foundation.org>
Depends-on: e18eb8783e ("tracing: Add tracing_reset_all_online_cpus_unlocked() function")
Depends-on: 5448d44c38 ("tracing: Add unified dynamic event framework")
Depends-on: 6212dd2968 ("tracing/kprobes: Use dyn_event framework for kprobe events")
Depends-on: 065e63f951 ("tracing: Only have rmmod clear buffers that its events were active in")
Depends-on: 575380da8b ("tracing: Only clear trace buffer on module unload if event was traced")
Fixes: 77b44d1b7c ("tracing/kprobes: Rename Kprobe-tracer to kprobe-event")
Reported-by: Zheng Yejian <zhengyejian1@huawei.com>
Reported-by: Yujie Liu <yujie.liu@intel.com>
Reported-by: kernel test robot <yujie.liu@intel.com>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 12b8b046e4 upstream.
Users of intel_gt_retire_requests_timeout() expect 0 return value on
success. However, we have no protection from passing back 0 potentially
returned by a call to dma_fence_wait_timeout() when it succedes right
after its timeout has expired.
Replace 0 with -ETIME before potentially using the timeout value as return
code, so -ETIME is returned if there are still some requests not retired
after timeout, 0 otherwise.
v3: Use conditional expression, more compact but also better reflecting
intention standing behind the change.
v2: Move the added lines down so flush_submission() is not affected.
Fixes: f33a8a5160 ("drm/i915: Merge wait_for_timelines with retire_request")
Signed-off-by: Janusz Krzysztofik <janusz.krzysztofik@linux.intel.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: stable@vger.kernel.org # v5.5+
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221121145655.75141-3-janusz.krzysztofik@linux.intel.com
(cherry picked from commit f301a29f14)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8899b8728 upstream.
Commit b97060a99b ("drm/i915/guc: Update intel_gt_wait_for_idle to work
with GuC") extended the API of intel_gt_retire_requests_timeout() with an
extra argument 'remaining_timeout', intended for passing back unconsumed
portion of requested timeout when 0 (success) is returned. However, when
request retirement happens to succeed despite an error returned by a call
to dma_fence_wait_timeout(), that error code (a negative value) is passed
back instead of remaining time. If we then pass that negative value
forward as requested timeout to intel_uc_wait_for_idle(), an explicit BUG
will be triggered.
If request retirement succeeds but an error code is passed back via
remaininig_timeout, we may have no clue on how much of the initial timeout
might have been left for spending it on waiting for GuC to become idle.
OTOH, since all pending requests have been successfully retired, that
error code has been already ignored by intel_gt_retire_requests_timeout(),
then we shouldn't fail.
Assume no more time has been left on error and pass 0 timeout value to
intel_uc_wait_for_idle() to give it a chance to return success if GuC is
already idle.
v3: Don't fail on any error passed back via remaining_timeout.
v2: Fix the issue on the caller side, not the provider.
Fixes: b97060a99b ("drm/i915/guc: Update intel_gt_wait_for_idle to work with GuC")
Signed-off-by: Janusz Krzysztofik <janusz.krzysztofik@linux.intel.com>
Cc: stable@vger.kernel.org # v5.15+
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221121145655.75141-2-janusz.krzysztofik@linux.intel.com
(cherry picked from commit f235dbd5b7)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c981cdfb99 upstream.
Commit 20b92a30b5 ("mmc: sdhci: update signal voltage switch code")
removed voltage switch delays from sdhci because mmc core had been
enhanced to support them. However that assumed that sdhci_set_ios()
did a single clock change, which it did not, and so the delays in mmc
core, which should have come after the first clock change, were not
effective.
Fix by avoiding re-configuring UHS and preset settings when the clock
is turning on and the settings have not changed. That then also avoids
the associated clock changes, so that then sdhci_set_ios() does a single
clock change when voltage switching, and the mmc core delays become
effective.
To do that has meant keeping track of driver strength (host->drv_type),
and cases of reinitialization (host->reinit_uhs).
Note also, the 'turning_on_clk' restriction should not be necessary
but is done to minimize the impact of the change on stable kernels.
Fixes: 20b92a30b5 ("mmc: sdhci: update signal voltage switch code")
Cc: stable@vger.kernel.org
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20221128133259.38305-2-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc3d2b5fc0 upstream.
Currently, pause frame register GMAC_RX_FLOW_CTRL_RFE is not updated
correctly when 'ethtool -A <IFACE> autoneg off rx off tx off' command
is issued. This fix ensures the flow control change is reflected directly
in the GMAC_RX_FLOW_CTRL_RFE register.
Fixes: 46f69ded98 ("net: stmmac: Use resolved link config in mac_link_up()")
Cc: <stable@vger.kernel.org> # 5.10.x
Signed-off-by: Goh, Wei Sheng <wei.sheng.goh@intel.com>
Signed-off-by: Noor Azura Ahmad Tarmizi <noor.azura.ahmad.tarmizi@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6647e76ab6 upstream.
The V4L2_MEMORY_USERPTR interface is long deprecated and shouldn't be
used (and is discouraged for any modern v4l drivers). And Seth Jenkins
points out that the fallback to VM_PFNMAP/VM_IO is fundamentally racy
and dangerous.
Note that it's not even a case that should trigger, since any normal
user pointer logic ends up just using the pin_user_pages_fast() call
that does the proper page reference counting. That's not the problem
case, only if you try to use special device mappings do you have any
issues.
Normally I'd just remove this during the merge window, but since Seth
pointed out the problem cases, we really want to know as soon as
possible if there are actually any users of this odd special case of a
legacy interface. Neither Hans nor Mauro seem to think that such
mis-uses of the old legacy interface should exist. As Mauro says:
"See, V4L2 has actually 4 streaming APIs:
- Kernel-allocated mmap (usually referred simply as just mmap);
- USERPTR mmap;
- read();
- dmabuf;
The USERPTR is one of the oldest way to use it, coming from V4L
version 1 times, and by far the least used one"
And Hans chimed in on the USERPTR interface:
"To be honest, I wouldn't mind if it goes away completely, but that's a
bit of a pipe dream right now"
but while removing this legacy interface entirely may be a pipe dream we
can at least try to remove the unlikely (and actively broken) case of
using special device mappings for USERPTR accesses.
This replaces it with a WARN_ONCE() that we can remove once we've
hopefully confirmed that no actual users exist.
NOTE! Longer term, this means that a 'struct frame_vector' only ever
contains proper page pointers, and all the games we have with converting
them to pages can go away (grep for 'frame_vector_to_pages()' and the
uses of 'vec->is_pfns'). But this is just the first step, to verify
that this code really is all dead, and do so as quickly as possible.
Reported-by: Seth Jenkins <sethjenkins@google.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: David Hildenbrand <david@redhat.com>
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6606515742 upstream.
The "force" argument to write_spec_ctrl_current() is currently ambiguous
as it does not guarantee the MSR write. This is due to the optimization
that writes to the MSR happen only when the new value differs from the
cached value.
This is fine in most cases, but breaks for S3 resume when the cached MSR
value gets out of sync with the hardware MSR value due to S3 resetting
it.
When x86_spec_ctrl_current is same as x86_spec_ctrl_base, the MSR write
is skipped. Which results in SPEC_CTRL mitigations not getting restored.
Move the MSR write from write_spec_ctrl_current() to a new function that
unconditionally writes to the MSR. Update the callers accordingly and
rename functions.
[ bp: Rework a bit. ]
Fixes: caa0ff24d5 ("x86/bugs: Keep a per-CPU IA32_SPEC_CTRL value")
Suggested-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@kernel.org>
Link: https://lore.kernel.org/r/806d39b0bfec2fe8f50dc5446dff20f5bb24a959.1669821572.git.pawan.kumar.gupta@linux.intel.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f0a0ccda18 upstream.
Syzbot reported a null-ptr-deref bug:
NILFS (loop0): segctord starting. Construction interval = 5 seconds, CP
frequency < 30 seconds
general protection fault, probably for non-canonical address
0xdffffc0000000002: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000010-0x0000000000000017]
CPU: 1 PID: 3603 Comm: segctord Not tainted
6.1.0-rc2-syzkaller-00105-gb229b6ca5abb #0
Hardware name: Google Compute Engine/Google Compute Engine, BIOS Google
10/11/2022
RIP: 0010:nilfs_palloc_commit_free_entry+0xe5/0x6b0
fs/nilfs2/alloc.c:608
Code: 00 00 00 00 fc ff df 80 3c 02 00 0f 85 cd 05 00 00 48 b8 00 00 00
00 00 fc ff df 4c 8b 73 08 49 8d 7e 10 48 89 fa 48 c1 ea 03 <80> 3c 02
00 0f 85 26 05 00 00 49 8b 46 10 be a6 00 00 00 48 c7 c7
RSP: 0018:ffffc90003dff830 EFLAGS: 00010212
RAX: dffffc0000000000 RBX: ffff88802594e218 RCX: 000000000000000d
RDX: 0000000000000002 RSI: 0000000000002000 RDI: 0000000000000010
RBP: ffff888071880222 R08: 0000000000000005 R09: 000000000000003f
R10: 000000000000000d R11: 0000000000000000 R12: ffff888071880158
R13: ffff88802594e220 R14: 0000000000000000 R15: 0000000000000004
FS: 0000000000000000(0000) GS:ffff8880b9b00000(0000)
knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fb1c08316a8 CR3: 0000000018560000 CR4: 0000000000350ee0
Call Trace:
<TASK>
nilfs_dat_commit_free fs/nilfs2/dat.c:114 [inline]
nilfs_dat_commit_end+0x464/0x5f0 fs/nilfs2/dat.c:193
nilfs_dat_commit_update+0x26/0x40 fs/nilfs2/dat.c:236
nilfs_btree_commit_update_v+0x87/0x4a0 fs/nilfs2/btree.c:1940
nilfs_btree_commit_propagate_v fs/nilfs2/btree.c:2016 [inline]
nilfs_btree_propagate_v fs/nilfs2/btree.c:2046 [inline]
nilfs_btree_propagate+0xa00/0xd60 fs/nilfs2/btree.c:2088
nilfs_bmap_propagate+0x73/0x170 fs/nilfs2/bmap.c:337
nilfs_collect_file_data+0x45/0xd0 fs/nilfs2/segment.c:568
nilfs_segctor_apply_buffers+0x14a/0x470 fs/nilfs2/segment.c:1018
nilfs_segctor_scan_file+0x3f4/0x6f0 fs/nilfs2/segment.c:1067
nilfs_segctor_collect_blocks fs/nilfs2/segment.c:1197 [inline]
nilfs_segctor_collect fs/nilfs2/segment.c:1503 [inline]
nilfs_segctor_do_construct+0x12fc/0x6af0 fs/nilfs2/segment.c:2045
nilfs_segctor_construct+0x8e3/0xb30 fs/nilfs2/segment.c:2379
nilfs_segctor_thread_construct fs/nilfs2/segment.c:2487 [inline]
nilfs_segctor_thread+0x3c3/0xf30 fs/nilfs2/segment.c:2570
kthread+0x2e4/0x3a0 kernel/kthread.c:376
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:306
</TASK>
...
If DAT metadata file is corrupted on disk, there is a case where
req->pr_desc_bh is NULL and blocknr is 0 at nilfs_dat_commit_end() during
a b-tree operation that cascadingly updates ancestor nodes of the b-tree,
because nilfs_dat_commit_alloc() for a lower level block can initialize
the blocknr on the same DAT entry between nilfs_dat_prepare_end() and
nilfs_dat_commit_end().
If this happens, nilfs_dat_commit_end() calls nilfs_dat_commit_free()
without valid buffer heads in req->pr_desc_bh and req->pr_bitmap_bh, and
causes the NULL pointer dereference above in
nilfs_palloc_commit_free_entry() function, which leads to a crash.
Fix this by adding a NULL check on req->pr_desc_bh and req->pr_bitmap_bh
before nilfs_palloc_commit_free_entry() in nilfs_dat_commit_free().
This also calls nilfs_error() in that case to notify that there is a fatal
flaw in the filesystem metadata and prevent further operations.
Link: https://lkml.kernel.org/r/00000000000097c20205ebaea3d6@google.com
Link: https://lkml.kernel.org/r/20221114040441.1649940-1-zhangpeng362@huawei.com
Link: https://lkml.kernel.org/r/20221119120542.17204-1-konishi.ryusuke@gmail.com
Signed-off-by: ZhangPeng <zhangpeng362@huawei.com>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Reported-by: syzbot+ebe05ee8e98f755f61d0@syzkaller.appspotmail.com
Tested-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a4412fdd49 upstream.
The config to be able to inject error codes into any function annotated
with ALLOW_ERROR_INJECTION() is enabled when FUNCTION_ERROR_INJECTION is
enabled. But unfortunately, this is always enabled on x86 when KPROBES
is enabled, and there's no way to turn it off.
As kprobes is useful for observability of the kernel, it is useful to
have it enabled in production environments. But error injection should
be avoided. Add a prompt to the config to allow it to be disabled even
when kprobes is enabled, and get rid of the "def_bool y".
This is a kernel debug feature (it's in Kconfig.debug), and should have
never been something enabled by default.
Cc: stable@vger.kernel.org
Fixes: 540adea380 ("error-injection: Separate error-injection from kprobe")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b84f0f74d upstream.
For Lexicon I-ONIX FW810S, the call of ioctl(2) with
SNDRV_PCM_IOCTL_HW_PARAMS can returns -ETIMEDOUT. This is a regression due
to the commit 41319eb56e ("ALSA: dice: wait just for
NOTIFY_CLOCK_ACCEPTED after GLOBAL_CLOCK_SELECT operation"). The device
does not emit NOTIFY_CLOCK_ACCEPTED notification when accepting
GLOBAL_CLOCK_SELECT operation with the same parameters as current ones.
This commit fixes the regression. When receiving no notification, return
-ETIMEDOUT as long as operating for any change.
Fixes: 41319eb56e ("ALSA: dice: wait just for NOTIFY_CLOCK_ACCEPTED after GLOBAL_CLOCK_SELECT operation")
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20221130130604.29774-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6fdd5d2f8c upstream.
64-bit RISC-V kernels have the kernel image mapped separately to alias
the linear map. The linear map and the kernel image map are documented
as "direct mapping" and "kernel" respectively in [1].
At image load time, the linear map corresponding to the kernel image
is set to PAGE_READ permission, and the kernel image map is set to
PAGE_READ|PAGE_EXEC.
When the initmem is freed, the pages in the linear map should be
restored to PAGE_READ|PAGE_WRITE, whereas the corresponding pages in
the kernel image map should be restored to PAGE_READ, by removing the
PAGE_EXEC permission.
This is not the case. For 64-bit kernels, only the linear map is
restored to its proper page permissions at initmem free, and not the
kernel image map.
In practise this results in that the kernel can potentially jump to
dead __init code, and start executing invalid instructions, without
getting an exception.
Restore the freed initmem properly, by setting both the kernel image
map to the correct permissions.
[1] Documentation/riscv/vm-layout.rst
Fixes: e5c35fa040 ("riscv: Map the kernel with correct permissions the first time")
Signed-off-by: Björn Töpel <bjorn@rivosinc.com>
Reviewed-by: Alexandre Ghiti <alex@ghiti.fr>
Tested-by: Alexandre Ghiti <alex@ghiti.fr>
Link: https://lore.kernel.org/r/20221115090641.258476-1-bjorn@kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 74f6bb55c8 upstream.
lkp reported a build error, I tried the config and can reproduce
build error as below:
VDSOLD arch/riscv/kernel/vdso/vdso.so.dbg
ld.lld: error: section .note file range overlaps with .text
>>> .note range is [0x7C8, 0x803]
>>> .text range is [0x800, 0x1993]
ld.lld: error: section .text file range overlaps with .dynamic
>>> .text range is [0x800, 0x1993]
>>> .dynamic range is [0x808, 0x937]
ld.lld: error: section .note virtual address range overlaps with .text
>>> .note range is [0x7C8, 0x803]
>>> .text range is [0x800, 0x1993]
Fix it by setting DISABLE_BRANCH_PROFILING which will disable branch
tracing for vdso, thus avoid useless _ftrace_annotated_branch section
and _ftrace_branch section. Although we can also fix it by removing
the hardcoded .text begin address, but I think that's another story
and should be put into another patch.
Link: https://lore.kernel.org/lkml/202210122123.Cc4FPShJ-lkp@intel.com/#r
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Link: https://lore.kernel.org/r/20221102170254.1925-1-jszhang@kernel.org
Fixes: ad5d1122b8 ("riscv: use vDSO common flow to reduce the latency of the time-related functions")
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5daadc86f2 ]
syzbot reported use-after-free in tun_detach() [1]. This causes call
trace like below:
==================================================================
BUG: KASAN: use-after-free in notifier_call_chain+0x1ee/0x200 kernel/notifier.c:75
Read of size 8 at addr ffff88807324e2a8 by task syz-executor.0/3673
CPU: 0 PID: 3673 Comm: syz-executor.0 Not tainted 6.1.0-rc5-syzkaller-00044-gcc675d22e422 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/26/2022
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xd1/0x138 lib/dump_stack.c:106
print_address_description mm/kasan/report.c:284 [inline]
print_report+0x15e/0x461 mm/kasan/report.c:395
kasan_report+0xbf/0x1f0 mm/kasan/report.c:495
notifier_call_chain+0x1ee/0x200 kernel/notifier.c:75
call_netdevice_notifiers_info+0x86/0x130 net/core/dev.c:1942
call_netdevice_notifiers_extack net/core/dev.c:1983 [inline]
call_netdevice_notifiers net/core/dev.c:1997 [inline]
netdev_wait_allrefs_any net/core/dev.c:10237 [inline]
netdev_run_todo+0xbc6/0x1100 net/core/dev.c:10351
tun_detach drivers/net/tun.c:704 [inline]
tun_chr_close+0xe4/0x190 drivers/net/tun.c:3467
__fput+0x27c/0xa90 fs/file_table.c:320
task_work_run+0x16f/0x270 kernel/task_work.c:179
exit_task_work include/linux/task_work.h:38 [inline]
do_exit+0xb3d/0x2a30 kernel/exit.c:820
do_group_exit+0xd4/0x2a0 kernel/exit.c:950
get_signal+0x21b1/0x2440 kernel/signal.c:2858
arch_do_signal_or_restart+0x86/0x2300 arch/x86/kernel/signal.c:869
exit_to_user_mode_loop kernel/entry/common.c:168 [inline]
exit_to_user_mode_prepare+0x15f/0x250 kernel/entry/common.c:203
__syscall_exit_to_user_mode_work kernel/entry/common.c:285 [inline]
syscall_exit_to_user_mode+0x1d/0x50 kernel/entry/common.c:296
do_syscall_64+0x46/0xb0 arch/x86/entry/common.c:86
entry_SYSCALL_64_after_hwframe+0x63/0xcd
The cause of the issue is that sock_put() from __tun_detach() drops
last reference count for struct net, and then notifier_call_chain()
from netdev_state_change() accesses that struct net.
This patch fixes the issue by calling sock_put() from tun_detach()
after all necessary accesses for the struct net has done.
Fixes: 83c1f36f98 ("tun: send netlink notification when the device is modified")
Reported-by: syzbot+106f9b687cd64ee70cd1@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?id=96eb7f1ce75ef933697f24eeab928c4a716edefe [1]
Signed-off-by: Shigeru Yoshida <syoshida@redhat.com>
Link: https://lore.kernel.org/r/20221124175134.1589053-1-syoshida@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca57f02295 ]
The fileserver probing code attempts to work out the best fileserver to
use for a volume by retrieving the RTT calculated by AF_RXRPC for the
probe call sent to each server and comparing them. Sometimes, however,
no RTT estimate is available and rxrpc_kernel_get_srtt() returns false,
leading good fileservers to be given an RTT of UINT_MAX and thus causing
the rotation algorithm to ignore them.
Fix afs_select_fileserver() to ignore rxrpc_kernel_get_srtt()'s return
value and just take the estimated RTT it provides - which will be capped
at 1 second.
Fixes: 1d4adfaf65 ("rxrpc: Make rxrpc_kernel_get_srtt() indicate validity")
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
Tested-by: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Link: https://lore.kernel.org/r/166965503999.3392585.13954054113218099395.stgit@warthog.procyon.org.uk/
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cdde156011 ]
I got the following report while doing device(mscc-miim) load test
with CONFIG_OF_UNITTEST and CONFIG_OF_DYNAMIC enabled:
OF: ERROR: memory leak, expected refcount 1 instead of 2,
of_node_get()/of_node_put() unbalanced - destroy cset entry:
attach overlay node /spi/soc@0/mdio@7107009c/ethernet-phy@0
If the 'fwnode' is not an acpi node, the refcount is get in
fwnode_mdiobus_phy_device_register(), but it has never been
put when the device is freed in the normal path. So call
fwnode_handle_put() in phy_device_release() to avoid leak.
If it's an acpi node, it has never been get, but it's put
in the error path, so call fwnode_handle_get() before
phy_device_register() to keep get/put operation balanced.
Fixes: bc1bee3b87 ("net: mdiobus: Introduce fwnode_mdiobus_register_phy()")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20221124150130.609420-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3067bc61fc ]
As the call trace shows, the original skb was freed in tipc_msg_validate(),
and dereferencing the old skb cb would cause an use-after-free crash.
BUG: KASAN: use-after-free in tipc_crypto_rcv_complete+0x1835/0x2240 [tipc]
Call Trace:
<IRQ>
tipc_crypto_rcv_complete+0x1835/0x2240 [tipc]
tipc_crypto_rcv+0xd32/0x1ec0 [tipc]
tipc_rcv+0x744/0x1150 [tipc]
...
Allocated by task 47078:
kmem_cache_alloc_node+0x158/0x4d0
__alloc_skb+0x1c1/0x270
tipc_buf_acquire+0x1e/0xe0 [tipc]
tipc_msg_create+0x33/0x1c0 [tipc]
tipc_link_build_proto_msg+0x38a/0x2100 [tipc]
tipc_link_timeout+0x8b8/0xef0 [tipc]
tipc_node_timeout+0x2a1/0x960 [tipc]
call_timer_fn+0x2d/0x1c0
...
Freed by task 47078:
tipc_msg_validate+0x7b/0x440 [tipc]
tipc_crypto_rcv_complete+0x4b5/0x2240 [tipc]
tipc_crypto_rcv+0xd32/0x1ec0 [tipc]
tipc_rcv+0x744/0x1150 [tipc]
This patch fixes it by re-fetching the skb cb from the new allocated skb
after calling tipc_msg_validate().
Fixes: fc1b6d6de2 ("tipc: introduce TIPC encryption & authentication")
Reported-by: Shuang Li <shuali@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Link: https://lore.kernel.org/r/1b1cdba762915325bd8ef9a98d0276eb673df2a5.1669398403.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39f59bca27 ]
This patch changes the reported ethtool statistics for the lan9303
family of parts covered by this driver.
The TxUnderRun statistic label is renamed to RxShort to accurately
reflect what stat the device is reporting. I did not reorder the
statistics as that might cause problems with existing user code that
are expecting the stats at a certain offset.
Fixes: a1292595e0 ("net: dsa: add new DSA switch driver for the SMSC-LAN9303")
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221128193559.6572-1-jerry.ray@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a99e3c8ed ]
Fix build error reported on armhf while preparing 6.1-rc5
for Debian.
iosm_ipc_protocol.c:244:36: error: passing argument 3 of
'dma_alloc_coherent' from incompatible pointer type.
Change phy_ap_shm type from phys_addr_t to dma_addr_t.
Fixes: faed4c6f6f ("net: iosm: shared memory protocol")
Reported-by: Bonaccorso Salvatore <carnil@debian.org>
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 985a02e758 ]
sparse warnings - iosm_ipc_mux_codec.c:1474 using plain
integer as NULL pointer.
Use skb_trim() to reset skb tail & len.
Fixes: 9413491e20 ("net: iosm: encode or decode datagram")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9256db4e45 ]
In function nixge_hw_dma_bd_release() dereference of NULL pointer
priv->rx_bd_v is possible for the case of its allocation failure in
nixge_hw_dma_bd_init().
Move for() loop with priv->rx_bd_v dereference under the check for
its validity.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 492caffa8a ("net: ethernet: nixge: Add support for National Instruments XGE netdev")
Signed-off-by: Yuri Karpov <YKarpov@ispras.ru>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dcc14cfd7d ]
Both p9_fd_create_tcp() and p9_fd_create_unix() will call
p9_socket_open(). If the creation of p9_trans_fd fails,
p9_fd_create_tcp() and p9_fd_create_unix() will return an
error directly instead of releasing the cscoket, which will
result in a socket leak.
This patch adds sock_release() to fix the leak issue.
Fixes: 6b18662e23 ("9p connect fixes")
Signed-off-by: Wang Hai <wanghai38@huawei.com>
ACKed-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8f79dccd3 ]
The ntb_netdev_init_module() returns the ntb_transport_register_client()
directly without checking its return value, if
ntb_transport_register_client() failed, the NTB client device is not
unregistered.
Fix by unregister NTB client device when ntb_transport_register_client()
failed.
Fixes: 548c237c0a ("net: Add support for NTB virtual ethernet device")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46fb651253 ]
The am65_cpsw_nuss_cleanup_ndev() function calls unregister_netdev()
even if register_netdev() fails, which triggers WARN_ON(1) in
unregister_netdevice_many(). To fix it, make sure that
unregister_netdev() is called only on registered netdev.
Compile tested only.
Fixes: 84b4aa4932 ("net: ethernet: ti: am65-cpsw: add multi port support in mac-only mode")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 369eb2c9f1 ]
I got a null-ptr-deref report as following when doing fault injection test:
BUG: kernel NULL pointer dereference, address: 0000000000000058
Oops: 0000 [#1] PREEMPT SMP KASAN PTI
CPU: 1 PID: 253 Comm: 507-spi-dm9051 Tainted: G B N 6.1.0-rc3+
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014
RIP: 0010:klist_put+0x2d/0xd0
Call Trace:
<TASK>
klist_remove+0xf1/0x1c0
device_release_driver_internal+0x23e/0x2d0
bus_remove_device+0x1bd/0x240
device_del+0x357/0x770
phy_device_remove+0x11/0x30
mdiobus_unregister+0xa5/0x140
release_nodes+0x6a/0xa0
devres_release_all+0xf8/0x150
device_unbind_cleanup+0x19/0xd0
//probe path:
phy_device_register()
device_add()
phy_connect
phy_attach_direct() //set device driver
probe() //it's failed, driver is not bound
device_bind_driver() // probe failed, it's not called
//remove path:
phy_device_remove()
device_del()
device_release_driver_internal()
__device_release_driver() //dev->drv is not NULL
klist_remove() <- knode_driver is not added yet, cause null-ptr-deref
In phy_attach_direct(), after setting the 'dev->driver', probe() fails,
device_bind_driver() is not called, so the knode_driver->n_klist is not
set, then it causes null-ptr-deref in __device_release_driver() while
deleting device. Fix this by setting dev->driver to NULL in the error
path in phy_attach_direct().
Fixes: e13934563d ("[PATCH] PHY Layer fixup")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit acd3c92acc ]
In S1G beacon frames there shouldn't be multi-BSSID elements
since that's not supported, remove that to avoid a potential
integer underflow and/or misparsing the frames due to the
different length of the fixed part of the frame.
While at it, initialize non_tx_data so we don't send garbage
values to the user (even if it doesn't seem to matter now.)
Reported-and-tested-by: Sönke Huster <shuster@seemoo.tu-darmstadt.de>
Fixes: 9eaffe5078 ("cfg80211: convert S1G beacon to scan results")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f16b5c82a ]
For vendor elements, the code here assumes that 5 octets
are present without checking. Since the element itself is
already checked to fit, we only need to check the length.
Reported-and-tested-by: Sönke Huster <shuster@seemoo.tu-darmstadt.de>
Fixes: 0b8fb8235b ("cfg80211: Parsing of Multiple BSSID information in scanning")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2a83891130 ]
IPV6 addresses are purged when setting the number of rx/tx
rings using ethtool -G. The function aq_set_ringparam
calls dev_close, which removes the addresses. As a solution,
call an internal function (aq_ndev_close).
Fixes: c1af542795 ("net: aquantia: Ethtool based ring size configuration")
Signed-off-by: Izabela Bakollari <ibakolla@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8dbd6e4ce1 ]
The watchdog timer is used to monitor whether the process
of transmitting data is timeout. If we use qlcnic driver,
the dev_watchdog() that is the timer handler of watchdog
timer will call qlcnic_tx_timeout() to process the timeout.
But the qlcnic_tx_timeout() calls msleep(), as a result,
the sleep-in-atomic-context bugs will happen. The processes
are shown below:
(atomic context)
dev_watchdog
qlcnic_tx_timeout
qlcnic_83xx_idc_request_reset
qlcnic_83xx_lock_driver
msleep
---------------------------
(atomic context)
dev_watchdog
qlcnic_tx_timeout
qlcnic_83xx_idc_request_reset
qlcnic_83xx_lock_driver
qlcnic_83xx_recover_driver_lock
msleep
Fix by changing msleep() to mdelay(), the mdelay() is
busy-waiting and the bugs could be mitigated.
Fixes: 629263acae ("qlcnic: 83xx CNA inter driver communication mechanism")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 52c795af04 ]
When having multiple dests with termination tables and second one
or afterwards fails the driver reverts usage of term tables but
doesn't reset the assignment in attr->dests[num_vport_dests].termtbl
which case a use-after-free when releasing the rule.
Fix by resetting the assignment of termtbl to null.
Fixes: 10caabdaad ("net/mlx5e: Use termination table for VLAN push actions")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f5769a074 ]
If sscanf() return 0, outlen is uninitialized and used in kzalloc(),
this is unexpected. We should return -EINVAL if the string is invalid.
Fixes: e126ba97db ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08fac109f7 ]
In dr_types structs, some list fields are list heads, and some
are just list nodes that are stored on the other structs' lists.
Rename the appropriate list field to reflect this distinction.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Stable-dep-of: 52f7cf70eb ("net/mlx5: DR, Fix uninitialized var warning")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 45605c75c5 ]
In e100_xmit_prepare(), if we can't map the skb, then return -ENOMEM, so
e100_xmit_frame() will return NETDEV_TX_BUSY and the upper layer will
resend the skb. But the skb is already freed, which will cause UAF bug
when the upper layer resends the skb.
Remove the harmful free.
Fixes: 5e5d49422d ("e100: Release skb when DMA mapping is failed in e100_xmit_prepare")
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 227d8d2f7f ]
The iavf_init_module() won't destroy workqueue when pci_register_driver()
failed. Call destroy_workqueue() when pci_register_driver() failed to
prevent the resource leak.
Similar to the handling of u132_hcd_init in commit f276e00279
("usb: u132-hcd: fix resource leak")
Fixes: 2803b16c10 ("i40e/i40evf: Use private workqueue")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 771a794c0a ]
A problem about modprobe fm10k failed is triggered with the following log
given:
Intel(R) Ethernet Switch Host Interface Driver
Copyright(c) 2013 - 2019 Intel Corporation.
debugfs: Directory 'fm10k' with parent '/' already present!
The reason is that fm10k_init_module() returns fm10k_register_pci_driver()
directly without checking its return value, if fm10k_register_pci_driver()
failed, it returns without removing debugfs and destroy workqueue,
resulting the debugfs of fm10k can never be created later and leaks the
workqueue.
fm10k_init_module()
alloc_workqueue()
fm10k_dbg_init() # create debugfs
fm10k_register_pci_driver()
pci_register_driver()
driver_register()
bus_add_driver()
priv = kzalloc(...) # OOM happened
# return without remove debugfs and destroy workqueue
Fix by remove debugfs and destroy workqueue when
fm10k_register_pci_driver() returns error.
Fixes: 7461fd913a ("fm10k: Add support for debugfs")
Fixes: b382bb1b3e ("fm10k: use separate workqueue for fm10k driver")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8cfa238a48 ]
ixgbevf_init_module() won't destroy the workqueue created by
create_singlethread_workqueue() when pci_register_driver() failed. Add
destroy_workqueue() in fail path to prevent the resource leak.
Similar to the handling of u132_hcd_init in commit f276e00279
("usb: u132-hcd: fix resource leak")
Fixes: 40a13e2493 ("ixgbevf: Use a private workqueue to avoid certain possible hangs")
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Reviewed-by: Saeed Mahameed <saeed@kernel.org>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 836e49e103 ]
bpf_selem_alloc function is used by inode_storage, sk_storage and
task_storage maps to set map value, for these map types, there may
be a spin lock in the map value, so if we use memcpy to copy the whole
map value from user, the spin lock field may be initialized incorrectly.
Since the spin lock field is zeroed by kzalloc, call copy_map_value
instead of memcpy to skip copying the spin lock field to fix it.
Fixes: 6ac99e8f23 ("bpf: Introduce bpf sk local storage")
Signed-off-by: Xu Kuohai <xukuohai@huawei.com>
Link: https://lore.kernel.org/r/20221114134720.1057939-2-xukuohai@huawei.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e2a87785aa ]
Smatch report warning as follows:
drivers/hwmon/ibmpex.c:509 ibmpex_register_bmc() warn:
'&data->list' not removed from list
If ibmpex_find_sensors() fails in ibmpex_register_bmc(), data will
be freed, but data->list will not be removed from driver_data.bmc_data,
then list traversal may cause UAF.
Fix by removeing it from driver_data.bmc_data before free().
Fixes: 57c7c3a0fd ("hwmon: IBM power meter driver")
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Link: https://lore.kernel.org/r/20221117034423.2935739-1-cuigaosheng1@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 927cbb478a ]
The maximum size of ringbuf is 2GB on x86-64 host, so 2 * max_entries
will overflow u32 when mapping producer page and data pages. Only
casting max_entries to size_t is not enough, because for 32-bits
application on 64-bits kernel the size of read-only mmap region
also could overflow size_t.
So fixing it by casting the size of read-only mmap region into a __u64
and checking whether or not there will be overflow during mmap.
Fixes: bf99c936f9 ("libbpf: Add BPF ring buffer support")
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20221116072351.1168938-3-houtao@huaweicloud.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d77de1581 ]
Commit 1d1a0e7c51 ("scripts/faddr2line: Fix overlapping text section
failures") can cause faddr2line to fail on ppc64le on some
distributions, while it works fine on other distributions. The failure
can be attributed to differences in the readelf output.
$ ./scripts/faddr2line vmlinux find_busiest_group+0x00
no match for find_busiest_group+0x00
On ppc64le, readelf adds the localentry tag before the symbol name on
some distributions, and adds the localentry tag after the symbol name on
other distributions. This problem has been discussed previously:
https://lore.kernel.org/bpf/20191211160133.GB4580@calabresa/
This problem can be overcome by filtering out the localentry tags in the
readelf output. Similar fixes are already present in the kernel by way
of the following commits:
1fd6cee127 ("libbpf: Fix VERSIONED_SYM_COUNT number parsing")
aa915931ac ("libbpf: Fix readelf output parsing for Fedora")
[jpoimboe: rework commit log]
Fixes: 1d1a0e7c51 ("scripts/faddr2line: Fix overlapping text section failures")
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Reviewed-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Link: https://lore.kernel.org/r/20220927075211.897152-1-srikar@linux.vnet.ibm.com
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 47df8a2f78 ]
Since commit bfea9a8574 ("bpf: Add name to struct bpf_ksym"), when
reporting subprog ksymbol to perf, prog name instead of subprog name is
used. The backtrace of bpf program with subprogs will be incorrect as
shown below:
ffffffffc02deace bpf_prog_e44a3057dcb151f8_overwrite+0x66
ffffffffc02de9f7 bpf_prog_e44a3057dcb151f8_overwrite+0x9f
ffffffffa71d8d4e trace_call_bpf+0xce
ffffffffa71c2938 perf_call_bpf_enter.isra.0+0x48
overwrite is the entry program and it invokes the overwrite_htab subprog
through bpf_loop, but in above backtrace, overwrite program just jumps
inside itself.
Fixing it by using subprog name when reporting subprog ksymbol. After
the fix, the output of perf script will be correct as shown below:
ffffffffc031aad2 bpf_prog_37c0bec7d7c764a4_overwrite_htab+0x66
ffffffffc031a9e7 bpf_prog_c7eb827ef4f23e71_overwrite+0x9f
ffffffffa3dd8d4e trace_call_bpf+0xce
ffffffffa3dc2938 perf_call_bpf_enter.isra.0+0x48
Fixes: bfea9a8574 ("bpf: Add name to struct bpf_ksym")
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/bpf/20221114095733.158588-1-houtao@huaweicloud.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ac1230357 ]
Fix an implicit declaration of function error for rpr0521 under some configs
When CONFIG_RPR0521 is enabled without CONFIG_IIO_TRIGGERED_BUFFER,
the build results in "implicit declaration of function" errors, e.g.,
drivers/iio/light/rpr0521.c:434:3: error: implicit declaration of function
'iio_trigger_poll_chained' [-Werror=implicit-function-declaration]
434 | iio_trigger_poll_chained(data->drdy_trigger0);
| ^~~~~~~~~~~~~~~~~~~~~~~~
This fix adds select dependencies to RPR0521's configuration declaration.
Fixes: e12ffd241c ("iio: light: rpr0521 triggered buffer")
Signed-off-by: Paul Gazzillo <paul@pgazz.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216678
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221110214729.ls5ixav5kxpeftk7@device
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc92d9e3de ]
KASAN report out-of-bounds read as follows:
BUG: KASAN: global-out-of-bounds in afe4404_read_raw+0x2ce/0x380
Read of size 4 at addr ffffffffc00e4658 by task cat/278
Call Trace:
afe4404_read_raw
iio_read_channel_info
dev_attr_show
The buggy address belongs to the variable:
afe4404_channel_leds+0x18/0xffffffffffffe9c0
This issue can be reproduce by singe command:
$ cat /sys/bus/i2c/devices/0-0058/iio\:device0/in_intensity6_raw
The array size of afe4404_channel_leds and afe4404_channel_offdacs
are less than channels, so access with chan->address cause OOB read
in afe4404_[read|write]_raw. Fix it by moving access before use them.
Fixes: b36e825764 ("iio: health/afe440x: Use regmap fields")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20221107152010.95937-1-weiyongjun@huaweicloud.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58143c1ed5 ]
KASAN report out-of-bounds read as follows:
BUG: KASAN: global-out-of-bounds in afe4403_read_raw+0x42e/0x4c0
Read of size 4 at addr ffffffffc02ac638 by task cat/279
Call Trace:
afe4403_read_raw
iio_read_channel_info
dev_attr_show
The buggy address belongs to the variable:
afe4403_channel_leds+0x18/0xffffffffffffe9e0
This issue can be reproduced by singe command:
$ cat /sys/bus/spi/devices/spi0.0/iio\:device0/in_intensity6_raw
The array size of afe4403_channel_leds is less than channels, so access
with chan->address cause OOB read in afe4403_read_raw. Fix it by moving
access before use it.
Fixes: b36e825764 ("iio: health/afe440x: Use regmap fields")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20221107151946.89260-1-weiyongjun@huaweicloud.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20543be93c ]
drm_display_info is updated by drm_get_edid() or
drm_connector_update_edid_property(). In the amdgpu driver it is almost
always updated when the edid is read in amdgpu_connector_get_edid(),
but not always. Change amdgpu_connector_get_edid() and
amdgpu_connector_free_edid() to keep drm_display_info updated.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Claudio Suarez <cssk@net-c.es>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stable-dep-of: 602ad43c3c ("drm/amdgpu: Partially revert "drm/amdgpu: update drm_display_info correctly when the edid is read"")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f3a127386 ]
Looks like that we're accidentally dropping a pretty important return code
here. For some reason, we just return -EINVAL if we fail to get the MST
topology state. This is wrong: error codes are important and should never
be squashed without being handled, which here seems to have the potential
to cause a deadlock.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Wayne Lin <Wayne.Lin@amd.com>
Fixes: 8ec046716c ("drm/dp_mst: Add helper to trigger modeset on affected DSC MST CRTCs")
Cc: <stable@vger.kernel.org> # v5.6+
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db5df25412 ]
Instead of having 2 places that short circuit the qgroup leaf scan have
everything in the qgroup_rescan_leaf function. In addition to that, also
ensure that the inconsistent qgroup flag is set when rescan_should_stop
returns true. This both retains the old behavior when -EINTR was set in
the body of the loop and at the same time also extends this behavior
when scanning is interrupted due to remount or unmount operations.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Stable-dep-of: f7e942b5bb ("btrfs: qgroup: fix sleep from invalid context bug in btrfs_qgroup_inherit()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db2d2dc9a0 ]
In case the requested bus clock is higher than the input clock, the correct
dividers (pre = 0, post = 0) are returned from mx51_ecspi_clkdiv(), but
*fres is left uninitialized and therefore contains an arbitrary value.
This causes trouble for the recently introduced PIO polling feature as the
value in spi_imx->spi_bus_clk is used there to calculate for which
transfers to enable PIO polling.
Fix this by setting *fres even if no clock dividers are in use.
This issue was observed on Kontron BL i.MX8MM with an SPI peripheral clock set
to 50 MHz by default and a requested SPI bus clock of 80 MHz for the SPI NOR
flash.
With the fix applied the debug message from mx51_ecspi_clkdiv() now prints the
following:
spi_imx 30820000.spi: mx51_ecspi_clkdiv: fin: 50000000, fspi: 50000000,
post: 0, pre: 0
Fixes: 6fd8b8503a ("spi: spi-imx: Fix out-of-order CS/SCLK operation at low speeds")
Fixes: 07e7593877 ("spi: spi-imx: add PIO polling support")
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: David Jander <david@protonic.nl>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Marek Vasut <marex@denx.de>
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20221115181002.2068270-1-frieder@fris.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 418ffb9e3c ]
btrfs_ioctl_logical_to_ino() frees the search path after the userspace
copy from the temp buffer @inodes. Which potentially can lead to a lock
splat.
Fix this by freeing the path before we copy @inodes to userspace.
CC: stable@vger.kernel.org # 4.19+
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3059ec06b ]
There's only one function we pass to iterate_inodes_from_logical as
iterator, so we can drop the indirection and call it directly, after
moving the function to backref.c
Signed-off-by: David Sterba <dsterba@suse.com>
Stable-dep-of: 418ffb9e3c ("btrfs: free btrfs_path before copying inodes to userspace")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0b0f2d225 ]
We currently have to special case vma->obj being NULL because
of gen6 ppgtt and mock_engine. Fix gen6 ppgtt, so we may soon
be able to remove a few checks. As the object only exists as
a fake object pointing to ggtt, we have no backing storage,
so no real object is created. It just has to look real enough.
Also kill pin_mutex, it's not compatible with ww locking,
and we can use the vm lock instead.
v2:
- Drop IS_SHRINKABLE and shorten overly long line
v3:
- Checkpatch fix for alignment
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211117142024.1043017-2-matthew.auld@intel.com
Stable-dep-of: 20e377e7b2 ("drm/i915/gt: Use i915_vm_put on ppgtt_create error paths")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a8e5e5146a ]
Prior to commit 69e3b846d8 ("arm64: mte: Sync tags for pages where PTE
is untagged"), mte_sync_tags() was only called for pte_tagged() entries
(those mapped with PROT_MTE). Therefore mte_sync_tags() could safely use
test_and_set_bit(PG_mte_tagged, &page->flags) without inadvertently
setting PG_mte_tagged on an untagged page.
The above commit was required as guests may enable MTE without any
control at the stage 2 mapping, nor a PROT_MTE mapping in the VMM.
However, the side-effect was that any page with a PTE that looked like
swap (or migration) was getting PG_mte_tagged set automatically. A
subsequent page copy (e.g. migration) copied the tags to the destination
page even if the tags were owned by KASAN.
This issue was masked by the page_kasan_tag_reset() call introduced in
commit e5b8d92189 ("arm64: mte: reset the page tag in page->flags").
When this commit was reverted (20794545c1), KASAN started reporting
access faults because the overriding tags in a page did not match the
original page->flags (with CONFIG_KASAN_HW_TAGS=y):
BUG: KASAN: invalid-access in copy_page+0x10/0xd0 arch/arm64/lib/copy_page.S:26
Read at addr f5ff000017f2e000 by task syz-executor.1/2218
Pointer tag: [f5], memory tag: [f2]
Move the PG_mte_tagged bit setting from mte_sync_tags() to the actual
place where tags are cleared (mte_sync_page_tags()) or restored
(mte_restore_tags()).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: syzbot+c2c79c6d6eddc5262b77@syzkaller.appspotmail.com
Fixes: 69e3b846d8 ("arm64: mte: Sync tags for pages where PTE is untagged")
Cc: <stable@vger.kernel.org> # 5.14.x
Cc: Steven Price <steven.price@arm.com>
Cc: Andrey Konovalov <andreyknvl@gmail.com>
Cc: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/0000000000004387dc05e5888ae5@google.com/
Reviewed-by: Steven Price <steven.price@arm.com>
Link: https://lore.kernel.org/r/20221006163354.3194102-1-catalin.marinas@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
This is a copy of README with the tags added.
You can not delete the file README as then checkpatch complains
you aren't in a kernel tree.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Builds the bcmrpi, bcm2709, bcm2711, and bcm2835 32 bit kernels,
and defconfig and bcm2711 64bit kernels, saving the artifacts for
7 days.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
We regularly get dmesg error reports of:
[ 18.184066] hdmi-audio-codec hdmi-audio-codec.3.auto: ASoC: error at snd_soc_dai_startup on i2s-hifi: -19
[ 18.184098] MAI: soc_pcm_open() failed (-19)
Currently I get 30 of these when booting to desktop.
We always say, ignore they are harmless, but removing them would be good.
A bit of investigation shows, for me, the errors are all generated by second, unused hdmi interface.
It shows as an alsa device, and pulseaudio attempts to open it (numerous times), generating a kernel
error message each time.
systemctl --user restart pulseaudio.service generates 6 additional error messages.
The error messages all come through:
a009a9c0d7/sound/soc/soc-pcm.c (L39)
which suggests returning ENOTSUPP, rather that ENODEV will be quiet. And indeed it is.
Note: earlier kernels do not have the quiet ENOTSUPP, so additional cherry-picks will be needed to backport
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
As there isn't currently a defined mechanism for selecting an
external trigger mode on image sensors, copy the imx477
approach of using a module parameter to enable ext trig.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The integrated USB2.0 hub in the VL805 chipset has a bug where it
incorrectly determines the remaining available frame time before the
host next sends a SOF packet with an incremented frame_number.
See the USB2.0 specification sections 11.3 and 11.14.2.3.
The hub's non-periodic TT handler can transmit the IN/OUT handshake
token too late, so a following 64-byte DATA0/1 packet causes the ACK
handshake to collide with the propagated SOF. This causes port babble.
Avoid ringing doorbells for vulnerable endpoints during uFrame 7 if the
TR is Idle to stop one source of babble. An IN transfer for a Running TR
may happen at any time, so there's not much we can do about that.
Ideally a hub firmware update to properly implement frame timeouts is
needed, and to avoid spinning for up to 125us when submitting TDs to
Idle rings.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
commit 65de262a20 upstream.
Fix missed refcounting of IPC tcon used for getting domain-based DFS
root referrals. We want to keep it alive as long as mount is active
and can be refreshed. For standalone DFS root referrals it wouldn't
be a problem as the client ends up having an IPC tcon for both mount
and cache.
Fixes: c88f7dcd6d ("cifs: support nested dfs links over reconnect")
Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Reviewed-by: Enzo Matsumiya <ematsumiya@suse.de>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a6e1775da0 upstream.
[why]
First MST sideband message returns AUX_RET_ERROR_HPD_DISCON
on certain intel platform. Aux transaction considered failure
if HPD unexpected pulled low. The actual aux transaction success
in such case, hence do not return error.
[how]
Not returning error when AUX_RET_ERROR_HPD_DISCON detected
on the first sideband message.
v2: squash in fix (Alex)
Reviewed-by: Jerry Zuo <Jerry.Zuo@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Tsung-hua Lin <Tsung-hua.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 44035ec2fd upstream.
There's been a very long running bug that seems to have been neglected for
a while, where amdgpu consistently triggers a KASAN error at start:
BUG: KASAN: global-out-of-bounds in read_indirect_azalia_reg+0x1d4/0x2a0 [amdgpu]
Read of size 4 at addr ffffffffc2274b28 by task modprobe/1889
After digging through amd's rather creative method for accessing registers,
I eventually discovered the problem likely has to do with the fact that on
my dce120 GPU there are supposedly 7 sets of audio registers. But we only
define a register mapping for 6 sets.
So, fix this and fix the KASAN warning finally.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 013c1c5585 upstream.
btrfs_ioctl_get_subvol_info() frees the search path after the userspace
copy from the temp buffer @subvol_info. This can lead to a lock splat
warning.
Fix this by freeing the path before we copy it to userspace.
CC: stable@vger.kernel.org # 4.19+
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8cf96b409d upstream.
btrfs_ioctl_ino_to_path() frees the search path after the userspace copy
from the temp buffer @ipath->fspath. Which potentially can lead to a lock
splat warning.
Fix this by freeing the path before we copy it to userspace.
CC: stable@vger.kernel.org # 4.19+
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
From: Marc Zyngier <maz@kernel.org>
commit c48c8b829d upstream.
Although setting the affinity of an interrupt to a set of CPUs that doesn't
have any online CPU is generally frowned apon, there are a few limited
cases where such affinity is set from a CPUHP notifier, setting the
affinity to a CPU that isn't online yet.
The saving grace is that this is always done using the 'force' attribute,
which gives a hint that the affinity setting can be outside of the online
CPU mask and the callsite set this flag with the knowledge that the
underlying interrupt controller knows to handle it.
This restores the expected behaviour on Marek's system.
Fixes: 33de0aa4ba ("genirq: Always limit the affinity to online CPUs")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/4b7fc13c-887b-a664-26e8-45aed13f048a@samsung.com
Link: https://lore.kernel.org/r/20220414140011.541725-1-maz@kernel.org
Signed-off-by: Luiz Capitulino <luizcap@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
From: Marc Zyngier <maz@kernel.org>
commit 33de0aa4ba upstream.
[ Fixed small conflicts due to the HK_FLAG_MANAGED_IRQ flag been
renamed on upstream ]
When booting with maxcpus=<small number> (or even loading a driver
while most CPUs are offline), it is pretty easy to observe managed
affinities containing a mix of online and offline CPUs being passed
to the irqchip driver.
This means that the irqchip cannot trust the affinity passed down
from the core code, which is a bit annoying and requires (at least
in theory) all drivers to implement some sort of affinity narrowing.
In order to address this, always limit the cpumask to the set of
online CPUs.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20220405185040.206297-3-maz@kernel.org
Signed-off-by: Luiz Capitulino <luizcap@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
From: Marc Zyngier <maz@kernel.org>
commit d802057c7c upstream.
[ This commit is almost a rewrite because it conflicts with Thomas
Gleixner's refactoring of this code in v5.17-rc1. I wasn't sure if
I should drop all the s-o-bs (including Mark's), but decided
to keep as the original commit ]
When booting with maxcpus=<small number>, interrupt controllers
such as the GICv3 ITS may not be able to satisfy the affinity of
some managed interrupts, as some of the HW resources are simply
not available.
The same thing happens when loading a driver using managed interrupts
while CPUs are offline.
In order to deal with this, do not try to activate such interrupt
if there is no online CPU capable of handling it. Instead, place
it in shutdown state. Once a capable CPU shows up, it will be
activated.
Reported-by: John Garry <john.garry@huawei.com>
Reported-by: David Decotigny <ddecotig@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/20220405185040.206297-2-maz@kernel.org
Signed-off-by: Luiz Capitulino <luizcap@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 44361e8cf9 upstream.
file_modified() must be called with inode lock held. fuse_fallocate()
didn't lock the inode in case of just FALLOC_KEEP_SIZE flags value, which
resulted in a kernel Warning in notify_change().
Lock the inode unconditionally, like all other fallocate implementations
do.
Reported-by: Pengfei Xu <pengfei.xu@intel.com>
Reported-and-tested-by: syzbot+462da39f0667b357c4b6@syzkaller.appspotmail.com
Fixes: 4a6f278d48 ("fuse: add file_modified() to fallocate")
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 984bf2cc53 ]
There was a problem that a user burned a dm-integrity image on CDROM
and could not activate it because it had a non-empty journal.
Fix this problem by flushing the journal (done by the previous commit)
and clearing the journal (done by this commit). Once the journal is
cleared, dm-integrity won't attempt to replay it on the next
activation.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5e5dab5ec7 ]
This commit flushes the journal on suspend. It is prerequisite for the
next commit that enables activating dm integrity devices in read-only mode.
Note that we deliberately didn't flush the journal on suspend, so that the
journal replay code would be tested. However, the dm-integrity code is 5
years old now, so that journal replay is well-tested, and we can make this
change now.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2418f911a ]
Since commit c7e3ca515e ("iommu/tegra: gart: Do not register with
bus") quite some time ago, the GART driver has effectively disabled
itself to avoid issues with the GPU driver expecting it to work in ways
that it doesn't. As of commit 57365a04c9 ("iommu: Move bus setup to
IOMMU device registration") that bodge no longer works, but really the
GPU driver should be responsible for its own behaviour anyway. Make the
workaround explicit.
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Suggested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f014165faa ]
If device_register() returns error, the name allocated by the
dev_set_name() need be freed. As described in the comment of
device_register(), we should use put_device() to give up the reference in
the error path.
Fix this by calling put_device(), the name will be freed in the
kobject_cleanup(), and this patch modified resources will be released by
calling the corresponding callback function in the device_release().
Signed-off-by: Zhou Guanghui <zhouguanghui1@huawei.com>
Link: https://lore.kernel.org/r/20221110033729.1555-1-zhouguanghui1@huawei.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aeac4ec8f4 ]
On embedded systems with little memory and no relevant
security concerns, it is beneficial to reduce the size
of the table.
Reducing the size from 2^16 to 2^8 saves 255 KiB
of kernel RAM.
Makes the table size configurable as an expert option.
The size was previously increased from 2^8 to 2^16
in commit 4c2c8f03a5 ("tcp: increase source port perturb table to
2^16").
Signed-off-by: Gleb Mazovetskiy <glex.spb@gmail.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 81a5603a0f ]
Commit 3ae86d2d47 ("platform/x86: ideapad-laptop: Fix Legion 5 Fn lock
LED") uses the WMI event-id for the fn-lock event on some Legion 5 laptops
to manually toggle the fn-lock LED because the EC does not do it itself.
However, the same WMI ID is also sent on some Yoga laptops. Here, setting
the fn-lock state is not valid behavior, and causes the EC to spam
interrupts until the laptop is rebooted.
Add a set_fn_lock_led_list[] DMI-id list and only enable the workaround to
manually set the LED on models on this list.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=212671
Cc: Meng Dong <whenov@gmail.com>
Signed-off-by: Arnav Rawat <arnavr3@illinois.edu>
Link: https://lore.kernel.org/r/12093851.O9o76ZdvQC@fedora
[hdegoede@redhat.com: Check DMI-id list only once and store the result]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7dd12d65ac ]
When an IO error occurs, the function __zonefs_io_error() is used to
issue a zone report to obtain the latest zone information from the
device. This function gets a zone report for all zones used as storage
for a file, which is always 1 zone except for files representing
aggregated conventional zones.
The number of zones of a zone report for a file is calculated in
__zonefs_io_error() by doing a bit-shift of the inode i_zone_size field,
which is equal to or larger than the device zone size. However, this
calculation does not take into account that the last zone of a zoned
device may be smaller than the zone size reported by bdev_zone_sectors()
(which is used to set the bit shift size). As a result, if an error
occurs for an IO targetting such last smaller zone, the zone report will
ask for 0 zones, leading to an invalid zone report.
Fix this by using the fact that all files require a 1 zone report,
except if the inode i_zone_size field indicates a zone size larger than
the device zone size. This exception case corresponds to a mount with
aggregated conventional zones.
A check for this exception is added to the file inode initialization
during mount. If an invalid setup is detected, emit an error and fail
the mount (check contributed by Johannes Thumshirn).
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5e29500eba ]
When Xen domain configures MSI-X, the usual approach is to enable MSI-X
together with masking all of them via the config space, then fill the
table and only then clear PCI_MSIX_FLAGS_MASKALL. Allow doing this via
QEMU running in a stub domain.
Previously, when changing PCI_MSIX_FLAGS_MASKALL was not allowed, the
whole write was aborted, preventing change to the PCI_MSIX_FLAGS_ENABLE
bit too.
Note the Xen hypervisor intercepts this write anyway, and may keep the
PCI_MSIX_FLAGS_MASKALL bit set if it wishes to. It will store the
guest-requested state and will apply it eventually.
Signed-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Link: https://lore.kernel.org/r/20221114103110.1519413-1-marmarek@invisiblethingslab.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e13757f524 ]
Like on the Acer Switch 10 SW5-012, the Acer Switch V 10 SW5-017's _LID
method messes with home- and power-button GPIO IRQ settings, causing an
IRQ storm.
Add a quirk entry for the Acer Switch V 10 to the dmi_use_low_level_irq[]
DMI quirk list, to use low-level IRQs on this model, fixing the IRQ storm.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20221106215320.67109-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e9ada1d0e ]
It seems that the Windows drivers for the ACPI0011 soc_button_array
device use low level triggered IRQs rather then using edge triggering.
Some ACPI tables depend on this, directly poking the GPIO controller's
registers to clear the trigger type when closing a laptop's/2-in-1's lid
and re-instating the trigger when opening the lid again.
Linux sets the edge/level on which to trigger to both low+high since
it is using edge type IRQs, the ACPI tables then ends up also setting
the bit for level IRQs and since both low and high level have been
selected by Linux we get an IRQ storm leading to soft lockups.
As a workaround for this the soc_button_array already contains
a DMI quirk table with device models known to have this issue.
Add a module parameter for this so that users can easily test if their
device is affected too and so that they can use the module parameter
as a workaround.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20221106215320.67109-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7e37cc624 ]
On ACPI systems (irq_pin_access_method == IRQ_PIN_ACCESS_ACPI_*) the driver
does not reset the controller at probe time, because sometimes the system
firmware loads a config and resetting might loose this config.
On the Nanote UMPC-01 device OTOH the config is in flash of the controller,
the controller needs a reset to load this; and the system firmware does not
reset the controller on a cold boot.
To fix the Nanote UMPC-01 touchscreen not working on a cold boot, try
resetting the controller and then re-reading the config when encountering
a config with 0 width/height/max_touch_num value and the controller has
not already been reset by goodix_ts_probe().
This should be safe to do in general because normally we should never
encounter a config with 0 width/height/max_touch_num. Doing this in
general not only avoids the need for a DMI quirk, but also might help
other systems.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20221025122930.421377-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 038ee49fef ]
RS485-enabled UART ports on TI Sitara SoCs with active-low polarity
exhibit a Transmit Enable glitch on ->set_termios():
omap8250_restore_regs(), which is called from omap_8250_set_termios(),
sets the TCRTLR bit in the MCR register and clears all other bits,
including RTS. If RTS uses active-low polarity, it is now asserted
for no reason.
The TCRTLR bit is subsequently cleared by writing up->mcr to the MCR
register. That variable is always zero, so the RTS bit is still cleared
(incorrectly so if RTS is active-high).
(up->mcr is not, as one might think, a cache of the MCR register's
current value. Rather, it only caches a single bit of that register,
the AFE bit. And it only does so if the UART supports the AFE bit,
which OMAP does not. For details see serial8250_do_set_termios() and
serial8250_do_set_mctrl().)
Finally at the end of omap8250_restore_regs(), the MCR register is
restored (and RTS deasserted) by a call to up->port.ops->set_mctrl()
(which equals serial8250_set_mctrl()) and serial8250_em485_stop_tx().
So there's an RTS glitch between setting TCRTLR and calling
serial8250_em485_stop_tx(). Avoid by using a read-modify-write
when setting TCRTLR.
While at it, drop a redundant initialization of up->mcr. As explained
above, the variable isn't used by the driver and it is already
initialized to zero because it is part of the static struct
serial8250_ports[] declared in 8250_core.c. (Static structs are
initialized to zero per section 6.7.8 nr. 10 of the C99 standard.)
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Su Bao Cheng <baocheng.su@siemens.com>
Tested-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/6554b0241a2c7fd50f32576fdbafed96709e11e8.1664278942.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c919b619b ]
When noevents is true and small buffer is used the allocated memory for
holding the data may be smaller than the hard-coded 64 bytes. This can
cause the iio_generic_buffer to crash.
Following was recorded on beagle bone black with v6.0 kernel and the
digit fix patch:
https://lore.kernel.org/all/Y0f+tKCz+ZAIoroQ@dc75zzyyyyyyyyyyyyycy-3.rev.dnainternet.fi/
using valgrind;
==339== Using Valgrind-3.18.1 and LibVEX; rerun with -h for copyright info
==339== Command: /iio_generic_buffer -n kx022-accel -T0 -e -l 10 -a -w 2000000
==339== Parent PID: 307
==339==
==339== Syscall param read(buf) points to unaddressable byte(s)
==339== at 0x496BFA4: read (read.c:26)
==339== by 0x11699: main (iio_generic_buffer.c:724)
==339== Address 0x4ab3518 is 0 bytes after a block of size 160 alloc'd
==339== at 0x4864B70: malloc (vg_replace_malloc.c:381)
==339== by 0x115BB: main (iio_generic_buffer.c:677)
Fix this by always using the same size for reading as was used for
data storage allocation.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/Y0kMh0t5qUXJw3nQ@dc75zzyyyyyyyyyyyyycy-3.rev.dnainternet.fi
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4dbd6a3e90 upstream.
Current code re-calculates the size after aligning the starting and
ending physical addresses on a page boundary. But the re-calculation
also embeds the masking of high order bits that exceed the size of
the physical address space (via PHYSICAL_PAGE_MASK). If the masking
removes any high order bits, the size calculation results in a huge
value that is likely to immediately fail.
Fix this by re-calculating the page-aligned size first. Then mask any
high order bits using PHYSICAL_PAGE_MASK.
Fixes: ffa71f33a8 ("x86, ioremap: Fix incorrect physical address handling in PAE mode")
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: <stable@kernel.org>
Link: https://lore.kernel.org/r/1668624097-14884-2-git-send-email-mikelley@microsoft.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 50bcceb772 upstream.
pm_save_spec_msr() keeps a list of all the MSRs which _might_ need
to be saved and restored at hibernate and resume. However, it has
zero awareness of CPU support for these MSRs. It mostly works by
unconditionally attempting to manipulate these MSRs and relying on
rdmsrl_safe() being able to handle a #GP on CPUs where the support is
unavailable.
However, it's possible for reads (RDMSR) to be supported for a given MSR
while writes (WRMSR) are not. In this case, msr_build_context() sees
a successful read (RDMSR) and marks the MSR as valid. Then, later, a
write (WRMSR) fails, producing a nasty (but harmless) error message.
This causes restore_processor_state() to try and restore it, but writing
this MSR is not allowed on the Intel Atom N2600 leading to:
unchecked MSR access error: WRMSR to 0x122 (tried to write 0x0000000000000002) \
at rIP: 0xffffffff8b07a574 (native_write_msr+0x4/0x20)
Call Trace:
<TASK>
restore_processor_state
x86_acpi_suspend_lowlevel
acpi_suspend_enter
suspend_devices_and_enter
pm_suspend.cold
state_store
kernfs_fop_write_iter
vfs_write
ksys_write
do_syscall_64
? do_syscall_64
? up_read
? lock_is_held_type
? asm_exc_page_fault
? lockdep_hardirqs_on
entry_SYSCALL_64_after_hwframe
To fix this, add the corresponding X86_FEATURE bit for each MSR. Avoid
trying to manipulate the MSR when the feature bit is clear. This
required adding a X86_FEATURE bit for MSRs that do not have one already,
but it's a small price to pay.
[ bp: Move struct msr_enumeration inside the only function that uses it. ]
Fixes: 73924ec4d5 ("x86/pm: Save the MSR validity status at context setup")
Reported-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: <stable@kernel.org>
Link: https://lore.kernel.org/r/c24db75d69df6e66c0465e13676ad3f2837a2ed8.1668539735.git.pawan.kumar.gupta@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aaa65d17ee upstream.
Support for the TSX control MSR is enumerated in MSR_IA32_ARCH_CAPABILITIES.
This is different from how other CPU features are enumerated i.e. via
CPUID. Currently, a call to tsx_ctrl_is_supported() is required for
enumerating the feature. In the absence of a feature bit for TSX control,
any code that relies on checking feature bits directly will not work.
In preparation for adding a feature bit check in MSR save/restore
during suspend/resume, set a new feature bit X86_FEATURE_TSX_CTRL when
MSR_IA32_TSX_CTRL is present. Also make tsx_ctrl_is_supported() use the
new feature bit to avoid any overhead of reading the MSR.
[ bp: Remove tsx_ctrl_is_supported(), add room for two more feature
bits in word 11 which are coming up in the next merge window. ]
Suggested-by: Andrew Cooper <andrew.cooper3@citrix.com>
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: <stable@kernel.org>
Link: https://lore.kernel.org/r/de619764e1d98afbb7a5fa58424f1278ede37b45.1668539735.git.pawan.kumar.gupta@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05311ce954 upstream.
It is valid to receive external interrupt and have broken IDT entry,
which will lead to #GP with exit_int_into that will contain the index of
the IDT entry (e.g any value).
Other exceptions can happen as well, like #NP or #SS
(if stack switch fails).
Thus this warning can be user triggred and has very little value.
Cc: stable@vger.kernel.org
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20221103141351.50662-10-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ed129ec905 upstream.
While not obivous, kvm_vcpu_reset() leaves the nested mode by clearing
'vcpu->arch.hflags' but it does so without all the required housekeeping.
On SVM, it is possible to have a vCPU reset while in guest mode because
unlike VMX, on SVM, INIT's are not latched in SVM non root mode and in
addition to that L1 doesn't have to intercept triple fault, which should
also trigger L1's reset if happens in L2 while L1 didn't intercept it.
If one of the above conditions happen, KVM will continue to use vmcb02
while not having in the guest mode.
Later the IA32_EFER will be cleared which will lead to freeing of the
nested guest state which will (correctly) free the vmcb02, but since
KVM still uses it (incorrectly) this will lead to a use after free
and kernel crash.
This issue is assigned CVE-2022-3344
Cc: stable@vger.kernel.org
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20221103141351.50662-5-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f53af4285d upstream.
During proactive reclaim, we sometimes observe severe overreclaim, with
several thousand times more pages reclaimed than requested.
This trace was obtained from shrink_lruvec() during such an instance:
prio:0 anon_cost:1141521 file_cost:7767
nr_reclaimed:4387406 nr_to_reclaim:1047 (or_factor:4190)
nr=[7161123 345 578 1111]
While he reclaimer requested 4M, vmscan reclaimed close to 16G, most of it
by swapping. These requests take over a minute, during which the write()
to memory.reclaim is unkillably stuck inside the kernel.
Digging into the source, this is caused by the proportional reclaim
bailout logic. This code tries to resolve a fundamental conflict: to
reclaim roughly what was requested, while also aging all LRUs fairly and
in accordance to their size, swappiness, refault rates etc. The way it
attempts fairness is that once the reclaim goal has been reached, it stops
scanning the LRUs with the smaller remaining scan targets, and adjusts the
remainder of the bigger LRUs according to how much of the smaller LRUs was
scanned. It then finishes scanning that remainder regardless of the
reclaim goal.
This works fine if priority levels are low and the LRU lists are
comparable in size. However, in this instance, the cgroup that is
targeted by proactive reclaim has almost no files left - they've already
been squeezed out by proactive reclaim earlier - and the remaining anon
pages are hot. Anon rotations cause the priority level to drop to 0,
which results in reclaim targeting all of anon (a lot) and all of file
(almost nothing). By the time reclaim decides to bail, it has scanned
most or all of the file target, and therefor must also scan most or all of
the enormous anon target. This target is thousands of times larger than
the reclaim goal, thus causing the overreclaim.
The bailout code hasn't changed in years, why is this failing now? The
most likely explanations are two other recent changes in anon reclaim:
1. Before the series starting with commit 5df741963d ("mm: fix LRU
balancing effect of new transparent huge pages"), the VM was
overall relatively reluctant to swap at all, even if swap was
configured. This means the LRU balancing code didn't come into play
as often as it does now, and mostly in high pressure situations
where pronounced swap activity wouldn't be as surprising.
2. For historic reasons, shrink_lruvec() loops on the scan targets of
all LRU lists except the active anon one, meaning it would bail if
the only remaining pages to scan were active anon - even if there
were a lot of them.
Before the series starting with commit ccc5dc6734 ("mm/vmscan:
make active/inactive ratio as 1:1 for anon lru"), most anon pages
would live on the active LRU; the inactive one would contain only a
handful of preselected reclaim candidates. After the series, anon
gets aged similarly to file, and the inactive list is the default
for new anon pages as well, making it often the much bigger list.
As a result, the VM is now more likely to actually finish large
anon targets than before.
Change the code such that only one SWAP_CLUSTER_MAX-sized nudge toward the
larger LRU lists is made before bailing out on a met reclaim goal.
This fixes the extreme overreclaim problem.
Fairness is more subtle and harder to evaluate. No obvious misbehavior
was observed on the test workload, in any case. Conceptually, fairness
should primarily be a cumulative effect from regular, lower priority
scans. Once the VM is in trouble and needs to escalate scan targets to
make forward progress, fairness needs to take a backseat. This is also
acknowledged by the myriad exceptions in get_scan_count(). This patch
makes fairness decrease gradually, as it keeps fairness work static over
increasing priority levels with growing scan targets. This should make
more sense - although we may have to re-visit the exact values.
Link: https://lkml.kernel.org/r/20220802162811.39216-1-hannes@cmpxchg.org
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Rik van Riel <riel@surriel.com>
Acked-by: Mel Gorman <mgorman@techsingularity.net>
Cc: Hugh Dickins <hughd@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 512c5ca01a upstream.
When extending segments, nilfs_sufile_alloc() is called to get an
unassigned segment, then mark it as dirty to avoid accidentally allocating
the same segment in the future.
But for some special cases such as a corrupted image it can be unreliable.
If such corruption of the dirty state of the segment occurs, nilfs2 may
reallocate a segment that is in use and pick the same segment for writing
twice at the same time.
This will cause the problem reported by syzkaller:
https://syzkaller.appspot.com/bug?id=c7c4748e11ffcc367cef04f76e02e931833cbd24
This case started with segbuf1.segnum = 3, nextnum = 4 when constructed.
It supposed segment 4 has already been allocated and marked as dirty.
However the dirty state was corrupted and segment 4 usage was not dirty.
For the first time nilfs_segctor_extend_segments() segment 4 was allocated
again, which made segbuf2 and next segbuf3 had same segment 4.
sb_getblk() will get same bh for segbuf2 and segbuf3, and this bh is added
to both buffer lists of two segbuf. It makes the lists broken which
causes NULL pointer dereference.
Fix the problem by setting usage as dirty every time in
nilfs_sufile_mark_dirty(), which is called during constructing current
segment to be written out and before allocating next segment.
[chenzhongjin@huawei.com: add lock protection per Ryusuke]
Link: https://lkml.kernel.org/r/20221121091141.214703-1-chenzhongjin@huawei.com
Link: https://lkml.kernel.org/r/20221118063304.140187-1-chenzhongjin@huawei.com
Fixes: 9ff05123e3 ("nilfs2: segment constructor")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Reported-by: <syzbot+77e4f0...@syzkaller.appspotmail.com>
Reported-by: Liu Shixin <liushixin2@huawei.com>
Acked-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Tested-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b44c0e7fef ]
The functions stop_active_transfers and ep_disable are both calling
remove_requests. This functions in both cases will giveback the requests
with status ESHUTDOWN, which also represents an physical disconnection.
For ep_disable this is not true. This patch adds the status parameter to
remove_requests and sets the status to ECONNRESET on ep_disable.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220720213523.1055897-1-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: f90f5afd50 ("usb: dwc3: gadget: Clear ep descriptor last")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ff5a19909b upstream.
We face some regressions on a few IXP42x systems when
accessing flash, the following unrelated error prints
appear from the PCI driver:
ixp4xx-pci c0000000.pci: PCI: abort_handler addr = 0xff9ffb5f,
isr = 0x0, status = 0x22a0
ixp4xx-pci c0000000.pci: imprecise abort
(...)
It turns out that while bit 7 is masked "reserved" it is
not unused, so masking it off as zero is dangerous, and
breaks flash access on some systems such as the NSLU2.
Be more careful and avoid masking off any of the reserved
bits 7, 8, 9 or 30. Only keep masking EXP_WORD (bit 2)
on IXP43x which is necessary in some setups.
Fixes: 1c953bda90 ("bus: ixp4xx: Add a driver for IXP4xx expansion bus")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221122134411.2030372-1-linus.walleij@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4ad09d956f upstream.
In iio_register_sw_trigger_type(), configfs_register_default_group() is
possible to fail, but the entry add to iio_trigger_types_list is not
deleted.
This leaves wild in iio_trigger_types_list, which can cause page fault
when module is loading again. So fix this by list_del(&t->list) in error
path.
BUG: unable to handle page fault for address: fffffbfff81d7400
Call Trace:
<TASK>
iio_register_sw_trigger_type
do_one_initcall
do_init_module
load_module
...
Fixes: b662f809d4 ("iio: core: Introduce IIO software triggers")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Link: https://lore.kernel.org/r/20221108032802.168623-1-chenzhongjin@huawei.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f6b1a1cf1c upstream.
If the starting position of our insert range happens to be in the hole
between the two ext4_extent_idx, because the lblk of the ext4_extent in
the previous ext4_extent_idx is always less than the start, which leads
to the "extent" variable access across the boundary, the following UAF is
triggered:
==================================================================
BUG: KASAN: use-after-free in ext4_ext_shift_extents+0x257/0x790
Read of size 4 at addr ffff88819807a008 by task fallocate/8010
CPU: 3 PID: 8010 Comm: fallocate Tainted: G E 5.10.0+ #492
Call Trace:
dump_stack+0x7d/0xa3
print_address_description.constprop.0+0x1e/0x220
kasan_report.cold+0x67/0x7f
ext4_ext_shift_extents+0x257/0x790
ext4_insert_range+0x5b6/0x700
ext4_fallocate+0x39e/0x3d0
vfs_fallocate+0x26f/0x470
ksys_fallocate+0x3a/0x70
__x64_sys_fallocate+0x4f/0x60
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xa9
==================================================================
For right shifts, we can divide them into the following situations：
1. When the first ee_block of ext4_extent_idx is greater than or equal to
start, make right shifts directly from the first ee_block.
1) If it is greater than start, we need to continue searching in the
previous ext4_extent_idx.
2) If it is equal to start, we can exit the loop (iterator=NULL).
2. When the first ee_block of ext4_extent_idx is less than start, then
traverse from the last extent to find the first extent whose ee_block
is less than start.
1) If extent is still the last extent after traversal, it means that
the last ee_block of ext4_extent_idx is less than start, that is,
start is located in the hole between idx and (idx+1), so we can
exit the loop directly (break) without right shifts.
2) Otherwise, make right shifts at the corresponding position of the
found extent, and then exit the loop (iterator=NULL).
Fixes: 331573febb ("ext4: Add support FALLOC_FL_INSERT_RANGE for fallocate")
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Link: https://lore.kernel.org/r/20220922120434.1294789-1-libaokun1@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel has an awfully complicated boot sequence in order to cope
with the various EL2 configurations, including those that "enhanced"
the architecture. We go from EL2 to EL1, then back to EL2, staying
at EL2 if VHE capable and otherwise go back to EL1.
Here's a paracetamol tablet for you.
The cpu_resume path follows the same logic, because coming up with
two versions of a square wheel is hard.
However, things aren't this straightforward with pKVM, as the host
resume path is always proxied by the hypervisor, which means that
the kernel is always entered at EL1. Which contradicts what the
__boot_cpu_mode[] array contains (it obviously says EL2).
This thus triggers a HVC call from EL1 to EL2 in a vain attempt
to upgrade from EL1 to EL2 VHE, which we are, funnily enough,
reluctant to grant to the host kernel. This is also completely
unexpected, and puzzles your average EL2 hacker.
Address it by fixing up the boot mode at the point the host gets
deprivileged. is_hyp_mode_available() and co already have a static
branch to deal with this, making it pretty safe.
This stable fix doesn't have an upstream version. The entire bootflow
has been reworked from 6.0 and that fixed the boot mode at the same
time, from commit 005e12676a ("arm64: head: record CPU boot mode after
enabling the MMU") to be precise. However, the latter is part of a 20
patches long series and can't be simply cherry-pick'ed.
Link: https://lore.kernel.org/r/20220624150651.1358849-1-ardb@kernel.org/
Link: https://lore.kernel.org/r/20221011165400.1241729-1-maz@kernel.org/
Cc: <stable@vger.kernel.org> # 5.15+
Reported-by: Vincent Donnefort <vdonnefort@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Tested-by: Vincent Donnefort <vdonnefort@google.com>
[Vincent: Add a paragraph about why this patch is for stable only]
Signed-off-by: Vincent Donnefort <vdonnefort@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 56baa208f9 ]
[[ NOTE: this is completely untested by the author, but included solely
because, as noted in commit df57d73276 ("mmc: sdhci-pci: Fix
SDHCI_RESET_ALL for CQHCI for Intel GLK-based controllers"), "other
drivers using CQHCI might benefit from a similar change, if they
also have CQHCI reset by SDHCI_RESET_ALL." We've now seen the same
bug on at least MSM, Arasan, and Intel hardware. ]]
SDHCI_RESET_ALL resets will reset the hardware CQE state, but we aren't
tracking that properly in software. When out of sync, we may trigger
various timeouts.
It's not typical to perform resets while CQE is enabled, but this may
occur in some suspend or error recovery scenarios.
Include this fix by way of the new sdhci_and_cqhci_reset() helper.
I only patch the bcm7216 variant even though others potentially *could*
provide the 'supports-cqe' property (and thus enable CQHCI), because
d46ba2d17f ("mmc: sdhci-brcmstb: Add support for Command Queuing
(CQE)") and some Broadcom folks confirm that only the 7216 variant
actually supports it.
This patch depends on (and should not compile without) the patch
entitled "mmc: cqhci: Provide helper for resetting both SDHCI and
CQHCI".
Fixes: d46ba2d17f ("mmc: sdhci-brcmstb: Add support for Command Queuing (CQE)")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221026124150.v4.3.I6a715feab6d01f760455865e968ecf0d85036018@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6bcc55fe64 ]
Enabling this feature will allow the controller to stop the bus
clock when the bus is idle. The feature is not part of the standard
and is unique to newer Arasan cores and is enabled with a bit in a
vendor specific register. This feature will only be enabled for
non-removable devices because they don't switch the voltage and
clock gating breaks SD Card volatge switching.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20220427180853.35970-3-kdasu.kdev@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Stable-dep-of: 56baa208f9 ("mmc: sdhci-brcmstb: Fix SDHCI_RESET_ALL for CQHCI")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 869e4ae4cd ]
Add FORCE to placate a warning from make:
arch/nios2/boot/Makefile:24: FORCE prerequisite is missing
Fixes: 2fc8483fdc ("nios2: Build infrastructure")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 534bd70374 ]
When using dash as /bin/sh, the CC_HAS_ASM_GOTO_TIED_OUTPUT test fails
with a syntax error which is not the one we are looking for:
<stdin>: In function ‘foo’:
<stdin>:1:29: warning: missing terminating " character
<stdin>:1:29: error: missing terminating " character
<stdin>:2:5: error: expected ‘:’ before ‘+’ token
<stdin>:2:7: warning: missing terminating " character
<stdin>:2:7: error: missing terminating " character
<stdin>:2:5: error: expected declaration or statement at end of input
Removing '\n' solves this.
Fixes: 1aa0e8b144 ("Kconfig: Add option for asm goto w/ tied outputs to workaround clang-13 bug")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f44e07a8af ]
The size of the TOD programmable field was incorrectly increased from
four to eight bytes with commit 1a2c5840ac ("s390/dump: cleanup CPU
save area handling").
This leads to an elf notes section NT_S390_TODPREG which has a size of
eight instead of four bytes in case of kdump, however even worse is
that the contents is incorrect: it is supposed to contain only the
contents of the TOD programmable field, but in fact contains a mix of
the TOD programmable field (32 bit upper bits) and parts of the CPU
timer register (lower 32 bits).
Fix this by simply changing the size of the todpreg field within the
save area structure. This will implicitly also fix the size of the
corresponding elf notes sections.
This also gets rid of this compile time warning:
in function ‘fortify_memcpy_chk’,
inlined from ‘save_area_add_regs’ at arch/s390/kernel/crash_dump.c:99:2:
./include/linux/fortify-string.h:413:25: error: call to ‘__read_overflow2_field’
declared with attribute warning: detected read beyond size of field
(2nd parameter); maybe use struct_group()? [-Werror=attribute-warning]
413 | __read_overflow2_field(q_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: 1a2c5840ac ("s390/dump: cleanup CPU save area handling")
Reviewed-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad17c2a3f1 ]
pci_get_device() will decrease the reference count for the *from*
parameter. So we don't need to call put_device() to decrease the
reference. Let's remove the put_device() in the loop and only decrease
the reference count of the returned 'pdev' for the last loop because it
will not be passed to pci_get_device() as input parameter. We don't need
to check if 'pdev' is NULL because it is already checked inside
pci_dev_put(). Also add pci_dev_put() for the error path.
Fixes: fe1939bb23 ("octeontx2-af: Add SDP interface support")
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Reviewed-by: Saeed Mahameed <saeed@kernel.org>
Link: https://lore.kernel.org/r/20221123065919.31499-1-wangxiongfeng2@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 290b5fe096 ]
In the blamed commit, a rudimentary reallocation procedure for RX buffer
descriptors was implemented, for the situation when their format changes
between normal (no PTP) and extended (PTP).
enetc_hwtstamp_set() calls enetc_close() and enetc_open() in a sequence,
and this sequence loses information which was previously configured in
the TX BDR Mode Register, specifically via the enetc_set_bdr_prio() call.
The TX ring priority is configured by tc-mqprio and tc-taprio, and
affects important things for TSN such as the TX time of packets. The
issue manifests itself most visibly by the fact that isochron --txtime
reports premature packet transmissions when PTP is first enabled on an
enetc interface.
Save the TX ring priority in a new field in struct enetc_bdr (occupies a
2 byte hole on arm64) in order to make this survive a ring reconfiguration.
Fixes: 434cebabd3 ("enetc: Add dynamic allocation of extended Rx BD rings")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Link: https://lore.kernel.org/r/20221122130936.1704151-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 715bf2610f ]
The &priv->si->hw construct dereferences 2 pointers and makes lines
longer than they need to be, in turn making the code harder to read.
Replace &priv->si->hw accesses with a "hw" variable when there are 2 or
more accesses within a function that dereference this. This includes
loops, since &priv->si->hw is a loop invariant.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 290b5fe096 ("net: enetc: preserve TX ring priority across reconfiguration")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 32bf8e1f6f ]
Future work in this driver would like to look at priv->active_offloads &
ENETC_F_QBV to determine whether a tc-taprio qdisc offload was
installed, but this does not produce the intended effect.
All the other flags in priv->active_offloads are managed dynamically,
except ENETC_F_QBV which is set statically based on the probed SI capability.
This change makes priv->active_offloads & ENETC_F_QBV really track the
presence of a tc-taprio schedule on the port.
Some existing users, like the enetc_sched_speed_set() call from
phylink_mac_link_up(), are best kept using the old logic: the tc-taprio
offload does not re-trigger another link mode resolve, so the scheduler
needs to be functional from the get go, as long as Qbv is supported at
all on the port. So to preserve functionality there, look at the static
station interface capability from pf->si->hw_features instead.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 290b5fe096 ("net: enetc: preserve TX ring priority across reconfiguration")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0254f31a7d ]
The transaction buffer is allocated by using the size of the packet buf,
and subtracting two which seems intended to remove the two tags which are
not present in the target structure. This calculation leads to under
counting memory because of differences between the packet contents and the
target structure. The aid_len field is a u8 in the packet, but a u32 in
the structure, resulting in at least 3 bytes always being under counted.
Further, the aid data is a variable length field in the packet, but fixed
in the structure, so if this field is less than the max, the difference is
added to the under counting.
To fix, perform validation checks progressively to safely reach the
next field, to determine the size of both buffers and verify both tags.
Once all validation checks pass, allocate the buffer and copy the data.
This eliminates freeing memory on the error path, as validation checks are
moved ahead of memory allocation.
Reported-by: Denis Efremov <denis.e.efremov@oracle.com>
Reviewed-by: Guenter Roeck <groeck@google.com>
Fixes: 5d1ceb7f5e ("NFC: st21nfcb: Add HCI transaction event support")
Signed-off-by: Martin Faltesek <mfaltesek@google.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c60c152230 ]
The first validation check for EVT_TRANSACTION has two different checks
tied together with logical AND. One is a check for minimum packet length,
and the other is for a valid aid_tag. If either condition is true (fails),
then an error should be triggered. The fix is to change && to ||.
Reported-by: Denis Efremov <denis.e.efremov@oracle.com>
Reviewed-by: Guenter Roeck <groeck@google.com>
Fixes: 5d1ceb7f5e ("NFC: st21nfcb: Add HCI transaction event support")
Signed-off-by: Martin Faltesek <mfaltesek@google.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 590ce6d96d ]
For DASD devices in raw_track_access mode only full track images are
read and written.
For this purpose it is not necessary to do search operation in the
locate record extended function. The documentation even states that
this might fail if the searched record is not found on a track.
Currently the driver sets a value of 1 in the search field for the first
record after record zero. This is the default for disks not in
raw_track_access mode but record 1 might be missing on a completely
empty track.
There has not been any problem with this on IBM storage servers but it
might lead to errors with DASD devices on other vendors storage servers.
Fix this by setting the search field to 0. Record zero is always available
even on a completely empty track.
Fixes: e4dbb0f2b5 ("[S390] dasd: Add support for raw ECKD access.")
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Link: https://lore.kernel.org/r/20221123160719.3002694-4-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c40cde6b5 ]
In com20020_probe(), if com20020_config() fails, dev and info
will not be freed, which will lead to a memory leak.
This patch adds freeing dev and info after com20020_config()
fails to fix this bug.
Compile tested only.
Fixes: 15b99ac172 ("[PATCH] pcmcia: add return value to _config() functions")
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77934dc6db ]
When connect() is called on a socket bound to the wildcard address,
we change the socket's saddr to a local address. If the socket
fails to connect() to the destination, we have to reset the saddr.
However, when an error occurs after inet_hash6?_connect() in
(dccp|tcp)_v[46]_conect(), we forget to reset saddr and leave
the socket bound to the address.
From the user's point of view, whether saddr is reset or not varies
with errno. Let's fix this inconsistent behaviour.
Note that after this patch, the repro [0] will trigger the WARN_ON()
in inet_csk_get_port() again, but this patch is not buggy and rather
fixes a bug papering over the bhash2's bug for which we need another
fix.
For the record, the repro causes -EADDRNOTAVAIL in inet_hash6_connect()
by this sequence:
s1 = socket()
s1.setsockopt(SOL_SOCKET, SO_REUSEADDR, 1)
s1.bind(('127.0.0.1', 10000))
s1.sendto(b'hello', MSG_FASTOPEN, (('127.0.0.1', 10000)))
# or s1.connect(('127.0.0.1', 10000))
s2 = socket()
s2.setsockopt(SOL_SOCKET, SO_REUSEADDR, 1)
s2.bind(('0.0.0.0', 10000))
s2.connect(('127.0.0.1', 10000)) # -EADDRNOTAVAIL
s2.listen(32) # WARN_ON(inet_csk(sk)->icsk_bind2_hash != tb2);
[0]: https://syzkaller.appspot.com/bug?extid=015d756bbd1f8b5c8f09
Fixes: 3df80d9320 ("[DCCP]: Introduce DCCPv6")
Fixes: 7c657876b6 ("[DCCP]: Initial implementation")
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Acked-by: Joanne Koong <joannelkoong@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e3c51f4e8 ]
After commit cbfecb927f ("fs: record I_DIRTY_TIME even if inode
already has I_DIRTY_INODE") writeback_single_inode can push inode with
I_DIRTY_TIME set to b_dirty_time list. In case of freeing inode with
I_DIRTY_TIME set this can happen after deletion of inode from i_io_list
at evict. Stack trace is following.
evict
fat_evict_inode
fat_truncate_blocks
fat_flush_inodes
writeback_inode
sync_inode_metadata(inode, sync=0)
writeback_single_inode(inode, wbc) <- wbc->sync_mode == WB_SYNC_NONE
This will lead to use after free in flusher thread.
Similar issue can be triggered if writeback_single_inode in the
stack trace update inode->i_io_list. Add explicit check to avoid it.
Fixes: cbfecb927f ("fs: record I_DIRTY_TIME even if inode already has I_DIRTY_INODE")
Reported-by: syzbot+6ba92bd00d5093f7e371@syzkaller.appspotmail.com
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Svyatoslav Feldsherov <feldsherov@google.com>
Link: https://lore.kernel.org/r/20221115202001.324188-1-feldsherov@google.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bcd9e3c165 ]
nf_flow_table_block_setup and the driver TC_SETUP_FT call can modify the flow
block cb list while they are being traversed elsewhere, causing a crash.
Add a write lock around the calls to protect readers
Fixes: c29f74e0df ("netfilter: nf_flow_table: hardware offload support")
Reported-by: Chad Monroe <chad.monroe@smartrg.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a66ce44a5 ]
The commit 510841da1f ("netfilter: ipset: enforce documented limit to
prevent allocating huge memory") was too strict and prevented to add up to
64 clashing elements to a hash:net,iface type of set. This patch fixes the
issue and now the type behaves as documented.
Fixes: 510841da1f ("netfilter: ipset: enforce documented limit to prevent allocating huge memory")
Signed-off-by: Jozsef Kadlecsik <kadlec@netfilter.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 40781bfb83 ]
When IPv6 module initializing in xfrm6_init(), register_pernet_subsys()
is possible to fail but its return value is ignored.
If IPv6 initialization fails later and xfrm6_fini() is called,
removing uninitialized list in xfrm6_net_ops will cause null-ptr-deref:
KASAN: null-ptr-deref in range [0x0000000000000008-0x000000000000000f]
CPU: 1 PID: 330 Comm: insmod
RIP: 0010:unregister_pernet_operations+0xc9/0x450
Call Trace:
<TASK>
unregister_pernet_subsys+0x31/0x3e
xfrm6_fini+0x16/0x30 [ipv6]
ip6_route_init+0xcd/0x128 [ipv6]
inet6_init+0x29c/0x602 [ipv6]
...
Fix it by catching the error return value of register_pernet_subsys().
Fixes: 8d068875ca ("xfrm: make gc_thresh configurable in all namespaces")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b97df039a6 ]
Kernel 5.14 added a new "byseq" index to speed
up xfrm_state lookups by sequence number in commit
fe9f1d8779 ("xfrm: add state hashtable keyed by seq")
While the patch was thorough, the function pfkey_send_new_mapping()
in net/af_key.c also modifies x->km.seq and never added
the current xfrm_state to the "byseq" index.
This leads to the following kernel Ooops:
BUG: kernel NULL pointer dereference, address: 0000000000000000
..
RIP: 0010:__xfrm_state_delete+0xc9/0x1c0
..
Call Trace:
<TASK>
xfrm_state_delete+0x1e/0x40
xfrm_del_sa+0xb0/0x110 [xfrm_user]
xfrm_user_rcv_msg+0x12d/0x270 [xfrm_user]
? remove_entity_load_avg+0x8a/0xa0
? copy_to_user_state_extra+0x580/0x580 [xfrm_user]
netlink_rcv_skb+0x51/0x100
xfrm_netlink_rcv+0x30/0x50 [xfrm_user]
netlink_unicast+0x1a6/0x270
netlink_sendmsg+0x22a/0x480
__sys_sendto+0x1a6/0x1c0
? __audit_syscall_entry+0xd8/0x130
? __audit_syscall_exit+0x249/0x2b0
__x64_sys_sendto+0x23/0x30
do_syscall_64+0x3a/0x90
entry_SYSCALL_64_after_hwframe+0x61/0xcb
Exact location of the crash in __xfrm_state_delete():
if (x->km.seq)
hlist_del_rcu(&x->byseq);
The hlist_node "byseq" was never populated.
The bug only triggers if a new NAT traversal mapping (changed IP or port)
is detected in esp_input_done2() / esp6_input_done2(), which in turn
indirectly calls pfkey_send_new_mapping() *if* the kernel is compiled
with CONFIG_NET_KEY and "af_key" is active.
The PF_KEYv2 message SADB_X_NAT_T_NEW_MAPPING is not part of RFC 2367.
Various implementations have been examined how they handle
the "sadb_msg_seq" header field:
- racoon (Android): does not process SADB_X_NAT_T_NEW_MAPPING
- strongswan: does not care about sadb_msg_seq
- openswan: does not care about sadb_msg_seq
There is no standard how PF_KEYv2 sadb_msg_seq should be populated
for SADB_X_NAT_T_NEW_MAPPING and it's not used in popular
implementations either. Herbert Xu suggested we should just
use the current km.seq value as is. This fixes the root cause
of the oops since we no longer modify km.seq itself.
The update of "km.seq" looks like a copy'n'paste error
from pfkey_send_acquire(). SADB_ACQUIRE must indeed assign a unique km.seq
number according to RFC 2367. It has been verified that code paths
involving pfkey_send_acquire() don't cause the same Oops.
PF_KEYv2 SADB_X_NAT_T_NEW_MAPPING support was originally added here:
https://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git
commit cbc3488685b20e7b2a98ad387a1a816aada569d8
Author: Derek Atkins <derek@ihtfp.com>
AuthorDate: Wed Apr 2 13:21:02 2003 -0800
[IPSEC]: Implement UDP Encapsulation framework.
In particular, implement ESPinUDP encapsulation for IPsec
Nat Traversal.
A note on triggering the bug: I was not able to trigger it using VMs.
There is one VPN using a high latency link on our production VPN server
that triggered it like once a day though.
Link: https://github.com/strongswan/strongswan/issues/992
Link: https://lore.kernel.org/netdev/00959f33ee52c4b3b0084d42c430418e502db554.1652340703.git.antony.antony@secunet.com/T/
Link: https://lore.kernel.org/netdev/20221027142455.3975224-1-chenzhihao@meizu.com/T/
Fixes: fe9f1d8779 ("xfrm: add state hashtable keyed by seq")
Reported-by: Roth Mark <rothm@mail.com>
Reported-by: Zhihao Chen <chenzhihao@meizu.com>
Tested-by: Roth Mark <rothm@mail.com>
Signed-off-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Acked-by: Antony Antony <antony.antony@secunet.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7b42969d6 ]
One extra conn_get() is needed in tipc_conn_alloc(), as after
tipc_conn_alloc() is called, tipc_conn_close() may free this
con before deferencing it in tipc_topsrv_accept():
tipc_conn_alloc();
newsk = newsock->sk;
<---- tipc_conn_close();
write_lock_bh(&sk->sk_callback_lock);
newsk->sk_data_ready = tipc_conn_data_ready;
Then an uaf issue can be triggered:
BUG: KASAN: use-after-free in tipc_topsrv_accept+0x1e7/0x370 [tipc]
Call Trace:
<TASK>
dump_stack_lvl+0x33/0x46
print_report+0x178/0x4b0
kasan_report+0x8c/0x100
kasan_check_range+0x179/0x1e0
tipc_topsrv_accept+0x1e7/0x370 [tipc]
process_one_work+0x6a3/0x1030
worker_thread+0x8a/0xdf0
This patch fixes it by holding it in tipc_conn_alloc(), then after
all accessing in tipc_topsrv_accept() releasing it. Note when does
this in tipc_topsrv_kern_subscr(), as tipc_conn_rcv_sub() returns
0 or -1 only, we don't need to check for "> 0".
Fixes: c5fa7b3cf3 ("tipc: introduce new TIPC server infrastructure")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e5d56c64a ]
A crash was reported by Wei Chen:
BUG: kernel NULL pointer dereference, address: 0000000000000018
RIP: 0010:tipc_conn_close+0x12/0x100
Call Trace:
tipc_topsrv_exit_net+0x139/0x320
ops_exit_list.isra.9+0x49/0x80
cleanup_net+0x31a/0x540
process_one_work+0x3fa/0x9f0
worker_thread+0x42/0x5c0
It was caused by !con->sock in tipc_conn_close(). In tipc_topsrv_accept(),
con is allocated in conn_idr then its sock is set:
con = tipc_conn_alloc();
... <----[1]
con->sock = newsock;
If tipc_conn_close() is called in anytime of [1], the null-pointer-def
is triggered by con->sock->sk due to con->sock is not yet set.
This patch fixes it by moving the con->sock setting to tipc_conn_alloc()
under s->idr_lock. So that con->sock can never be NULL when getting the
con from s->conn_idr. It will be also safer to move con->server and flag
CF_CONNECTED setting under s->idr_lock, as they should all be set before
tipc_conn_alloc() is called.
Fixes: c5fa7b3cf3 ("tipc: introduce new TIPC server infrastructure")
Reported-by: Wei Chen <harperchen1110@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aaf2e65cac ]
In case command interface is down, or the command is not allowed, driver
did not increment the entry refcount, but might have decrement as part
of forced completion handling.
Fix that by always increment and decrement the refcount to make it
symmetric for all flows.
Fixes: 50b2412b7e ("net/mlx5: Avoid possible free of command entry while timeout comp handler")
Signed-off-by: Eran Ben Elisha <eranbe@nvidia.com>
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reported-by: Jack Wang <jinpu.wang@ionos.com>
Tested-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61db3d7b99 ]
Fix a bug in calculation of FW tracer timestamp. Decreasing one in the
calculation should effect only bits 52_7 and not effect bits 6_0 of the
timestamp, otherwise bits 6_0 are always set in this calculation.
Fixes: 70dd6fdb89 ("net/mlx5: FW tracer, parse traces and kernel tracing support")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Feras Daoud <ferasda@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 394164f9d5 ]
The driver should not interact with PCI while PCI is disabled. Trying to
do so may result in being unable to get vital signs during PCI reset,
driver gets timed out and fails to recover.
Fixes: fad1783a6d ("net/mlx5: Print more info on pci error handlers")
Signed-off-by: Roy Novich <royno@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7aa1a76d4 ]
This patch introduced a regression: commit 48596a8ddc ("netfilter:
ipset: Fix adding an IPv4 range containing more than 2^31 addresses")
The variable e.ip is passed to adtfn() function which finally adds the
ip address to the set. The patch above refactored the for loop and moved
e.ip = htonl(ip) to the end of the for loop.
What this means is that if the value of "ip" changes between the first
assignement of e.ip and the forloop, then e.ip is pointing to a
different ip address than "ip".
Test case:
$ ipset create jdtest_tmp hash:ip family inet hashsize 2048 maxelem 100000
$ ipset add jdtest_tmp 10.0.1.1/31
ipset v6.21.1: Element cannot be added to the set: it's already added
The value of ip gets updated inside the "else if (tb[IPSET_ATTR_CIDR])"
block but e.ip is still pointing to the old value.
Fixes: 48596a8ddc ("netfilter: ipset: Fix adding an IPv4 range containing more than 2^31 addresses")
Reviewed-by: Joshua Hunt <johunt@akamai.com>
Signed-off-by: Vishwanath Pai <vpai@akamai.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0873016d46 ]
Setting of the port flag `NFP_PORT_CHANGED`, introduced
to ensure the correct reading of EEPROM data, causes a
fatal kernel NULL pointer dereference in cases where
the target netdev type cannot be determined.
Add validation of port struct pointer before attempting
to set the `NFP_PORT_CHANGED` flag. Return that operation
is not supported if the netdev type cannot be determined.
Fixes: 4ae97cae07 ("nfp: ethtool: fix the display error of `ethtool -m DEVNAME`")
Signed-off-by: Jaco Coetzee <jaco.coetzee@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4abd9600b9 ]
The error is reflected in that it shows wrong splittable status of
port when executing "devlink port show".
The reason which leads the error is that the assigned operation of
splittable is just a simple negation operation of split and it does
not consider port lanes quantity. A splittable port should have
several lanes that can be split(lanes quantity > 1).
If without the judgement, it will show wrong message for some
firmware, such as 2x25G, 2x10G.
Fixes: a0f49b5486 ("devlink: Add a new devlink port split ability attribute and pass to netlink")
Signed-off-by: Diana Wang <na.wang@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5619537284 ]
As comment of pci_get_domain_bus_and_slot() says, it returns
a pci device with refcount increment, when finish using it,
the caller must decrement the reference count by calling
pci_dev_put().
In pch_gbe_probe(), pci_get_domain_bus_and_slot() is called,
so in error path in probe() and remove() function, pci_dev_put()
should be called to avoid refcount leak. Compile tested only.
Fixes: 1a0bdadb4e ("net/pch_gbe: supports eg20t ptp clock")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221117135148.301014-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d66608803a ]
As comment of pci_get_domain_bus_and_slot() says, it returns
a pci device with refcount increment, when finish using it,
the caller must decrement the reference count by calling
pci_dev_put().
So before returning from rvu_dbg_rvu_pf_cgx_map_display() or
cgx_print_dmac_flt(), pci_dev_put() is called to avoid refcount
leak.
Fixes: dbc52debf9 ("octeontx2-af: Debugfs support for DMAC filters")
Fixes: e2fb373038 ("octeontx2-af: Display CGX, NIX and PF map in debugfs.")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221117124658.162409-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e68be7b39f ]
make dtbs_check gives the following errors:
ref-clock-frequency: size (9) error for type uint32
tcxo-clock-frequency: size (9) error for type uint32
Fix it by passing the frequencies inside < > as documented in
Documentation/devicetree/bindings/net/wireless/ti,wlcore.yaml.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Fixes: 0d446a5055 ("ARM: dts: add Protonic PRTI6Q board")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a8417330f8 ]
Fix a deadlock introduced by commit
974578017f ("iavf: Add waiting so the port is initialized in remove")
due to race condition between iavf_shutdown and iavf_remove, where
iavf_remove stucks forever in while loop since iavf_shutdown already
set __IAVF_REMOVE adapter state.
Fix this by checking if the __IAVF_IN_REMOVE_TASK has already been
set and return if so.
Fixes: 974578017f ("iavf: Add waiting so the port is initialized in remove")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Marek Szlosek <marek.szlosek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 33c7aba0b4 ]
Elements with an end interval flag set on do not store extensions. The
global set definition is currently setting on the timeout and stateful
expression for end interval elements.
This leads to skipping end interval elements from the set->ops->walk()
path as the expired check bogusly reports true.
Moreover, do not set up stateful expressions for elements with end
interval flag set on since this is never used.
Fixes: 65038428b2 ("netfilter: nf_tables: allow to specify stateful expression in set definition")
Fixes: 8d8540c4f5 ("netfilter: nft_set_rbtree: add timeout support")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 52d1aa8b82 ]
nf_conn:mark can be read from and written to in parallel. Use
READ_ONCE()/WRITE_ONCE() for reads and writes to prevent unwanted
compiler optimizations.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Daniel Xu <dxu@dxuuu.xyz>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11c1095651 ]
Syz reported the following issue:
kernel BUG at lib/list_debug.c:53!
invalid opcode: 0000 [#1] PREEMPT SMP KASAN
RIP: 0010:__list_del_entry_valid.cold+0x5c/0x72
Call Trace:
<TASK>
p9_fd_cancel+0xb1/0x270
p9_client_rpc+0x8ea/0xba0
p9_client_create+0x9c0/0xed0
v9fs_session_init+0x1e0/0x1620
v9fs_mount+0xba/0xb80
legacy_get_tree+0x103/0x200
vfs_get_tree+0x89/0x2d0
path_mount+0x4c0/0x1ac0
__x64_sys_mount+0x33b/0x430
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
</TASK>
The process is as follows:
Thread A: Thread B:
p9_poll_workfn() p9_client_create()
... ...
p9_conn_cancel() p9_fd_cancel()
list_del() ...
... list_del() //list_del
corruption
There is no lock protection when deleting list in p9_conn_cancel(). After
deleting list in Thread A, thread B will delete the same list again. It
will cause issue of list_del corruption.
Setting req->status to REQ_STATUS_ERROR under lock prevents other
cleanup paths from trying to manipulate req_list.
The other thread can safely check req->status because it still holds a
reference to req at this point.
Link: https://lkml.kernel.org/r/20221110122606.383352-1-shaozhengchao@huawei.com
Fixes: 52f1c45dde ("9p: trans_fd/p9_conn_cancel: drop client lock earlier")
Reported-by: syzbot+9b69b8d10ab4a7d88056@syzkaller.appspotmail.com
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
[Dominique: add description of the fix in commit message]
Signed-off-by: Dominique Martinet <asmadeus@codewreck.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2360f9b8c4 ]
In pch_gbe_xmit_frame(), NETDEV_TX_OK will be returned whether
pch_gbe_tx_queue() sends data successfully or not, so pch_gbe_tx_queue()
needs to free skb before returning. But pch_gbe_tx_queue() returns without
freeing skb in case of dma_map_single() fails. Add dev_kfree_skb_any()
to fix it.
Fixes: 77555ee722 ("net: Add Gigabit Ethernet driver of Topcliff PCH")
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ad6bded17 ]
Previously we leverage NCI_UNREG and the lock inside nci_close_device to
prevent the race condition between opening a device and closing a
device. However, it still has problem because a failed opening command
will erase the NCI_UNREG flag and allow another opening command to
bypass the status checking.
This fix corrects that by making sure the NCI_UNREG is held.
Reported-by: syzbot+43475bf3cfbd6e41f5b7@syzkaller.appspotmail.com
Fixes: 48b71a9e66 ("NFC: add NCI_UNREG flag to eliminate the race")
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24deec6b9e ]
You'd think people know that the internal 100BASE-TX PHY on the SJA1110
responds only to clause 22 MDIO transactions, but they don't :)
When a clause 45 transaction is attempted, sja1105_base_tx_mdio_read()
and sja1105_base_tx_mdio_write() don't expect "reg" to contain bit 30
set (MII_ADDR_C45) and pack this value into the SPI transaction buffer.
But the field in the SPI buffer has a width smaller than 30 bits, so we
see this confusing message from the packing() API rather than a proper
rejection of C45 transactions:
Call trace:
dump_stack+0x1c/0x38
sja1105_pack+0xbc/0xc0 [sja1105]
sja1105_xfer+0x114/0x2b0 [sja1105]
sja1105_xfer_u32+0x44/0xf4 [sja1105]
sja1105_base_tx_mdio_read+0x44/0x7c [sja1105]
mdiobus_read+0x44/0x80
get_phy_c45_ids+0x70/0x234
get_phy_device+0x68/0x15c
fwnode_mdiobus_register_phy+0x74/0x240
of_mdiobus_register+0x13c/0x380
sja1105_mdiobus_register+0x368/0x490 [sja1105]
sja1105_setup+0x94/0x119c [sja1105]
Cannot store 401d2405 inside bits 24-4 (would truncate)
Fixes: 5a8f09748e ("net: dsa: sja1105: register the MDIO buses for 100base-T1 and 100base-TX")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3bcd6c7eaa ]
After rxrpc_unbundle_conn() has removed a connection from a bundle, it
checks to see if there are any conns with available channels and, if not,
removes and attempts to destroy the bundle.
Whilst it does check after grabbing client_bundles_lock that there are no
connections attached, this races with rxrpc_look_up_bundle() retrieving the
bundle, but not attaching a connection for the connection to be attached
later.
There is therefore a window in which the bundle can get destroyed before we
manage to attach a new connection to it.
Fix this by adding an "active" counter to struct rxrpc_bundle:
(1) rxrpc_connect_call() obtains an active count by prepping/looking up a
bundle and ditches it before returning.
(2) If, during rxrpc_connect_call(), a connection is added to the bundle,
this obtains an active count, which is held until the connection is
discarded.
(3) rxrpc_deactivate_bundle() is created to drop an active count on a
bundle and destroy it when the active count reaches 0. The active
count is checked inside client_bundles_lock() to prevent a race with
rxrpc_look_up_bundle().
(4) rxrpc_unbundle_conn() then calls rxrpc_deactivate_bundle().
Fixes: 245500d853 ("rxrpc: Rewrite the client connection manager")
Reported-by: zdi-disclosures@trendmicro.com # ZDI-CAN-15975
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: zdi-disclosures@trendmicro.com
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 33912c2639 ]
Allow the list of in-use local UDP endpoints in the current network
namespace to be viewed in /proc.
To aid with this, the endpoint list is converted to an hlist and RCU-safe
manipulation is used so that the list can be read with only the RCU
read lock held.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 3bcd6c7eaa ("rxrpc: Fix race between conn bundle lookup and bundle removal [ZDI-CAN-15975]")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 733d4bbf95 ]
Fix the warning reported by kbuild:
cocci warnings: (new ones prefixed by >>)
>> drivers/net/ethernet/cavium/liquidio/lio_main.c:1797:54-56: WARNING !A || A && B is equivalent to !A || B
drivers/net/ethernet/cavium/liquidio/lio_main.c:1827:54-56: WARNING !A || A && B is equivalent to !A || B
Fixes: 8979f428a4 ("net: liquidio: release resources when liquidio driver open failed")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Saeed Mahameed <saeed@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6ab64b074 ]
Currently the simult_flows.sh self-tests are not very stable,
especially when running on slow VMs.
The tests measure runtime for transfers on multiple subflows
and check that the time is near the theoretical maximum.
The current test infra introduces a bit of jitter in test
runtime, due to multiple explicit delays. Additionally the
runtime is measured by the shell script wrapper. On a slow
VM, the script overhead is measurable and subject to relevant
jitter.
One solution to make the test more stable would be adding more
slack to the expected time; that could possibly hide real
regressions. Instead move the measurement inside the command
doing the transfer, and drop most unneeded sleeps.
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 3de88b95c4 ("selftests: mptcp: fix mibit vs mbit mix up")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cce616e012 ]
If device_register() returns error in optee_register_device(),
the name allocated by dev_set_name() need be freed. As comment
of device_register() says, it should use put_device() to give
up the reference in the error path. So fix this by calling
put_device(), then the name can be freed in kobject_cleanup(),
and optee_device is freed in optee_release_device().
Fixes: c3fa24af92 ("tee: optee: add TEE bus device enumeration support")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1f386d6894 ]
I got a UAF report as following:
==================================================================
BUG: KASAN: use-after-free in __lock_acquire+0x935/0x2060
Read of size 8 at addr ffff88810e838220 by task python3/268
Call Trace:
<TASK>
dump_stack_lvl+0x67/0x83
print_report+0x178/0x4b0
kasan_report+0x90/0x190
__lock_acquire+0x935/0x2060
lock_acquire+0x156/0x400
_raw_spin_lock+0x2a/0x40
lockref_get+0x11/0x30
simple_recursive_removal+0x41/0x440
debugfs_remove.part.12+0x32/0x50
debugfs_remove+0x29/0x30
_regulator_put.cold.54+0x3e/0x27f
regulator_put+0x1f/0x30
release_nodes+0x6a/0xa0
devres_release_all+0xf8/0x150
Allocated by task 37:
kasan_save_stack+0x1c/0x40
kasan_set_track+0x21/0x30
__kasan_slab_alloc+0x5d/0x70
slab_post_alloc_hook+0x62/0x510
kmem_cache_alloc_lru+0x222/0x5a0
__d_alloc+0x31/0x440
d_alloc+0x30/0xf0
d_alloc_parallel+0xc4/0xd20
__lookup_slow+0x15e/0x2f0
lookup_one_len+0x13a/0x150
start_creating+0xea/0x190
debugfs_create_dir+0x1e/0x210
create_regulator+0x254/0x4e0
_regulator_get+0x2a1/0x467
_devm_regulator_get+0x5a/0xb0
regulator_virtual_probe+0xb9/0x1a0
Freed by task 30:
kasan_save_stack+0x1c/0x40
kasan_set_track+0x21/0x30
kasan_save_free_info+0x2a/0x50
__kasan_slab_free+0x102/0x190
kmem_cache_free+0xf6/0x600
rcu_core+0x54c/0x12b0
__do_softirq+0xf2/0x5e3
Last potentially related work creation:
kasan_save_stack+0x1c/0x40
__kasan_record_aux_stack+0x98/0xb0
call_rcu+0x42/0x700
dentry_free+0x6c/0xd0
__dentry_kill+0x23b/0x2d0
dput.part.31+0x431/0x780
simple_recursive_removal+0xa9/0x440
debugfs_remove.part.12+0x32/0x50
debugfs_remove+0x29/0x30
regulator_unregister+0xe3/0x230
release_nodes+0x6a/0xa0
==================================================================
Here is how happened:
processor A processor B
regulator_register()
rdev_init_debugfs()
rdev->debugfs = debugfs_create_dir()
devm_regulator_get()
rdev = regulator_dev_lookup()
create_regulator(rdev)
// using rdev->debugfs as parent
debugfs_create_dir(rdev->debugfs)
mfd_remove_devices_fn()
release_nodes()
regulator_unregister()
// free rdev->debugfs
debugfs_remove_recursive(rdev->debugfs)
release_nodes()
destroy_regulator()
debugfs_remove_recursive() <- causes UAF
In devm_regulator_get(), after getting rdev, the refcount
is get, so fix this by moving debugfs_remove_recursive()
to regulator_dev_release(), then it can be proctected by
the refcount, the 'rdev->debugfs' can not be freed until
the refcount is 0.
Fixes: 5de705194e ("regulator: Add basic per consumer debugfs")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221116033706.3595812-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f4b204b6b ]
Here is a warning report about lack of registered release()
from kobject lib:
Device '(null)' does not have a release() function, it is broken and must be fixed.
WARNING: CPU: 0 PID: 48430 at drivers/base/core.c:2332 device_release+0x104/0x120
Call Trace:
kobject_put+0xdc/0x180
put_device+0x1b/0x30
regulator_register+0x651/0x1170
devm_regulator_register+0x4f/0xb0
When regulator_register() returns fail and directly goto `clean` symbol,
rdev->dev has not registered release() function yet (which is registered
by regulator_class in the following), so rdev needs to be freed manually.
If rdev->dev.of_node is not NULL, which means the of_node has gotten by
regulator_of_get_init_data(), it needs to call of_node_put() to avoid
refcount leak.
Otherwise, only calling put_device() would lead memory leak of rdev
in further:
unreferenced object 0xffff88810d0b1000 (size 2048):
comm "107-i2c-rtq6752", pid 48430, jiffies 4342258431 (age 1341.780s)
backtrace:
kmalloc_trace+0x22/0x110
regulator_register+0x184/0x1170
devm_regulator_register+0x4f/0xb0
When regulator_register() returns fail and goto `wash` symbol,
rdev->dev has registered release() function, so directly call
put_device() to cleanup everything.
Fixes: d3c731564e ("regulator: plug of_node leak in regulator_register()'s error path")
Signed-off-by: Zeng Heng <zengheng4@huawei.com>
Link: https://lore.kernel.org/r/20221116074339.1024240-1-zengheng4@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8a5376c32 ]
Current handling of the srb_status is incorrect. Commit 52e1b3b3da
("scsi: storvsc: Correctly handle multiple flags in srb_status")
is based on srb_status being a set of flags, when in fact only the
2 high order bits are flags and the remaining 6 bits are an integer
status. Because the integer values of interest mostly look like flags,
the code actually works when treated that way.
But in the interest of correctness going forward, fix this by treating
the low 6 bits of srb_status as an integer status code. Add handling
for SRB_STATUS_INVALID_REQUEST, which was the original intent of commit
52e1b3b3da. Furthermore, treat the ERROR, ABORTED, and INVALID_REQUEST
srb status codes as essentially equivalent for the cases we care about.
There's no harm in doing so, and it isn't always clear which status code
current or older versions of Hyper-V report for particular conditions.
Treating the srb status codes as equivalent has the additional benefit
of ensuring that capacity change events result in an immediate rescan
so that the new size is known to Linux. Existing code checks SCSI
sense data for capacity change events when the srb status is ABORTED.
But capacity change events are also being observed when Hyper-V reports
the srb status as ERROR. Without the immediate rescan, the new size
isn't known until something else causes a rescan (such as running
fdisk to expand a partition), and in the meantime, tools such as "lsblk"
continue to report the old size.
Fixes: 52e1b3b3da ("scsi: storvsc: Correctly handle multiple flags in srb_status")
Reported-by: Juan Tian <juantian@microsoft.com>
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/1668019722-1983-1-git-send-email-mikelley@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee68154163 ]
Commit e5d9b714fe ("x86/hyperv: fix root partition faults when writing
to VP assist page MSR") moved 'wrmsrl(HV_X64_MSR_VP_ASSIST_PAGE)' under
'if (*hvp)' condition. This works for root partition as hv_cpu_die()
does memunmap() and sets 'hv_vp_assist_page[cpu]' to NULL but breaks
non-root partitions as hv_cpu_die() doesn't free 'hv_vp_assist_page[cpu]'
for them. This causes VP assist page to remain unset after CPU
offline/online cycle:
$ rdmsr -p 24 0x40000073
10212f001
$ echo 0 > /sys/devices/system/cpu/cpu24/online
$ echo 1 > /sys/devices/system/cpu/cpu24/online
$ rdmsr -p 24 0x40000073
0
Fix the issue by always writing to HV_X64_MSR_VP_ASSIST_PAGE in
hv_cpu_init(). Note, checking 'if (!*hvp)', for root partition is
pointless as hv_cpu_die() always sets 'hv_vp_assist_page[cpu]' to
NULL (and it's also NULL initially).
Note: the fact that 'hv_vp_assist_page[cpu]' is reset to NULL may
present a (potential) issue for KVM. While Hyper-V uses
CPUHP_AP_ONLINE_DYN stage in CPU hotplug, KVM uses CPUHP_AP_KVM_STARTING
which comes earlier in CPU teardown sequence. It is theoretically
possible that Enlightened VMCS is still in use. It is unclear if the
issue is real and if using KVM with Hyper-V root partition is even
possible.
While on it, drop the unneeded smp_processor_id() call from hv_cpu_init().
Fixes: e5d9b714fe ("x86/hyperv: fix root partition faults when writing to VP assist page MSR")
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/20221103190601.399343-1-vkuznets@redhat.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39bd801d69 ]
The DAI tx_mask and rx_mask are set by snd_soc_dai_set_tdm_slot()
and used by later code that depends on the TDM settings. So
__soc_pcm_open() should not be obliterating those mask values.
The code in __soc_pcm_hw_params() uses these masks to calculate the
active channels so that only the AIF_IN/AIF_OUT widgets for the
active TDM slots are enabled. The zeroing of the masks in
__soc_pcm_open() disables this functionality so all AIF widgets
were enabled even for channels that are not assigned to a TDM slot.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 2e5894d737 ("ASoC: pcm: Add support for DAI multicodec")
Link: https://lore.kernel.org/r/20221104132213.121847-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0bb8e9b36b ]
Since commit bf2aebccdd ("ASoC: sgtl5000: Fix noise on shutdown/remove"),
the device power control registers are reset when the driver is
removed/shutdown.
This is an issue when the device is configured to use the PLL clock. The
device will stop responding if it is still configured to use the PLL
clock but the PLL clock is powered down.
When rebooting linux, the probe function will show:
sgtl5000 0-000a: Error reading chip id -11
Make sure that the CHIP_CLK_CTRL is reset to its default value before
powering down the device.
Fixes: bf2aebccdd ("ASoC: sgtl5000: Fix noise on shutdown/remove")
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20221110190612.1341469-1-detlev.casanova@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8950f345a6 ]
Remove the regulators node and define fixed regulators in the root node.
Prevents the sdhci-omap driver from waiting in probe deferral forever
because of the missing vmmc-supply and keeps am335x-pcm-953 consistent with
the other Phytec AM335 boards.
Fixes: bb07a829ec ("ARM: dts: Add support for phyCORE-AM335x PCM-953 carrier board")
Signed-off-by: Dominik Haller <d.haller@phytec.de>
Message-Id: <20221011143115.248003-1-d.haller@phytec.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b549ccce9 ]
When using GSO it can happen that the wrong seq_hi is used for the last
packets before the wrap around. This can lead to double usage of a
sequence number. To avoid this, we should serialize this last GSO
packet.
Fixes: d7dbefc45c ("xfrm: Add xfrm_replay_overflow functions for offloading")
Co-developed-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Christian Langrock <christian.langrock@secunet.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a5913183a ]
The commit in the "Fixes" tag tried to avoid a case where policy check
is ignored due to dst caching in next hops.
However, when the traffic is locally consumed, the dst may be cached
in a local TCP or UDP socket as part of early demux. In this case the
"disable_policy" flag is not checked as ip_route_input_noref() was only
called before caching, and thus, packets after the initial packet in a
flow will be dropped if not matching policies.
Fix by checking the "disable_policy" flag also when a valid dst is
already available.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216557
Reported-by: Monil Patel <monil191989@gmail.com>
Fixes: e6175a2ed1 ("xfrm: fix "disable_policy" flag use when arriving from different devices")
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
----
v2: use dev instead of skb->dev
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 648060902a ]
get_port_from_cmdline() returns an int, yet is assigned to a char, which
is wrong in its own right, but also, with char becoming unsigned, this
poses problems, because -1 is used as an error value. Further
complicating things, fw_init_early_console() is only ever called with a
-1 argument. Fix this up by removing the unused argument from
fw_init_early_console() and treating port as a proper signed integer.
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fcae44fd36 ]
Recently, ld.lld moved from '--undefined-version' to
'--no-undefined-version' as the default, which breaks the compat vDSO
build:
ld.lld: error: version script assignment of 'LINUX_4.15' to symbol '__vdso_gettimeofday' failed: symbol not defined
ld.lld: error: version script assignment of 'LINUX_4.15' to symbol '__vdso_clock_gettime' failed: symbol not defined
ld.lld: error: version script assignment of 'LINUX_4.15' to symbol '__vdso_clock_getres' failed: symbol not defined
These symbols are not present in the compat vDSO or the regular vDSO for
32-bit but they are unconditionally included in the version section of
the linker script, which is prohibited with '--no-undefined-version'.
Fix this issue by only including the symbols that are actually exported
in the version section of the linker script.
Link: https://github.com/ClangBuiltLinux/linux/issues/1756
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20221108171324.3377226-1-nathan@kernel.org/
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit acfc35cfce ]
Add the same change for ARM64 as done in the commit 9440c42941
("x86/syscall: Include asm/ptrace.h in syscall_wrapper header") to
make sure all syscalls see 'struct pt_regs' definition and resulted
BTF for '__arm64_sys_*(struct pt_regs *regs)' functions point to
actual struct.
Without this patch, the BPF verifier refuses to load a tracing prog
which accesses pt_regs.
bpf(BPF_PROG_LOAD, {prog_type=0x1a, ...}, 128) = -1 EACCES
With this patch, we can see the correct error, which saves us time
in debugging the prog.
bpf(BPF_PROG_LOAD, {prog_type=0x1a, ...}, 128) = 4
bpf(BPF_RAW_TRACEPOINT_OPEN, {raw_tracepoint={name=NULL, prog_fd=4}}, 128) = -1 ENOTSUPP
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/r/20221031215728.50389-1-kuniyu@amazon.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ecb8c2580d ]
From ZBC-1:
- RC BASIS = 0: The RETURNED LOGICAL BLOCK ADDRESS field indicates the
highest LBA of a contiguous range of zones that are not sequential write
required zones starting with the first zone.
- RC BASIS = 1: The RETURNED LOGICAL BLOCK ADDRESS field indicates the LBA
of the last logical block on the logical unit.
The current scsi_debug READ CAPACITY response does not comply with the
above if there are one or more sequential write required zones. SCSI
initiators need a way to retrieve the largest valid LBA from SCSI
devices. Reporting the largest valid LBA if there are one or more
sequential zones requires to set the RC BASIS field in the READ CAPACITY
response to one. Hence this patch.
Cc: Douglas Gilbert <dgilbert@interlog.com>
Cc: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Suggested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20221102193248.3177608-1-bvanassche@acm.org
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62fa3ce05d ]
Fix an issue reported when performing a live migration when multipath is
configured with a short fast fail timeout of 5 seconds and also to have
no_path_retry set to fail. In this scenario, all paths would go into the
devloss state while the ibmvfc driver went through discovery to log back
in. On a loaded system, the discovery might take longer than 5 seconds,
which was resulting in all paths being marked failed, which then resulted
in a read only filesystem.
This patch changes the migration code in ibmvfc to avoid deleting rports at
all in this scenario, so we avoid losing all paths.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Link: https://lore.kernel.org/r/20221026181356.148517-1-brking@linux.vnet.ibm.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8bcd560ae8 ]
This reverts commit c850240b6c.
That commit tried to improve the performance of macsec offload by
taking advantage of some of the NIC's features, but in doing so, broke
macsec offload when the lower device supports both macsec and ipsec
offload, as the ipsec offload feature flags (mainly NETIF_F_HW_ESP)
were copied from the real device. Since the macsec device doesn't
provide xdo_* ops, the XFRM core rejects the registration of the new
macsec device in xfrm_api_check.
Example perf trace when running
ip link add link eni1np1 type macsec port 4 offload mac
ip 737 [003] 795.477676: probe:xfrm_dev_event__REGISTER name="macsec0" features=0x1c000080014869
xfrm_dev_event+0x3a
notifier_call_chain+0x47
register_netdevice+0x846
macsec_newlink+0x25a
ip 737 [003] 795.477687: probe:xfrm_dev_event__return ret=0x8002 (NOTIFY_BAD)
notifier_call_chain+0x47
register_netdevice+0x846
macsec_newlink+0x25a
dev->features includes NETIF_F_HW_ESP (0x04000000000000), so
xfrm_api_check returns NOTIFY_BAD because we don't have
dev->xfrmdev_ops on the macsec device.
We could probably propagate GSO and a few other features from the
lower device, similar to macvlan. This will be done in a future patch.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 475244f5e0 ]
Add a test case to ensure that released pointer registers will not be
leaked into the map.
Before fix:
./test_verifier 984
984/u reference tracking: try to leak released ptr reg FAIL
Unexpected success to load!
verification time 67 usec
stack depth 4
processed 23 insns (limit 1000000) max_states_per_insn 0 total_states 2
peak_states 2 mark_read 1
984/p reference tracking: try to leak released ptr reg OK
Summary: 1 PASSED, 0 SKIPPED, 1 FAILED
After fix:
./test_verifier 984
984/u reference tracking: try to leak released ptr reg OK
984/p reference tracking: try to leak released ptr reg OK
Summary: 2 PASSED, 0 SKIPPED, 0 FAILED
Signed-off-by: Youlin Li <liulin063@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20221103093440.3161-2-liulin063@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62aa1a344b ]
When this driver is used with a driver that uses preallocated spi_transfer
structs. The speed_hz is halved by every run. This results in:
spi_stm32 44004000.spi: SPI transfer setup failed
ads7846 spi0.0: SPI transfer failed: -22
Example when running with DIV_ROUND_UP():
- First run; speed_hz = 1000000, spi->clk_rate 125000000
div 125 -> mbrdiv = 7, cur_speed = 976562
- Second run; speed_hz = 976562
div 128,00007 (roundup to 129) -> mbrdiv = 8, cur_speed = 488281
- Third run; speed_hz = 488281
div 256,000131072067109 (roundup to 257) and then -EINVAL is returned.
Use DIV_ROUND_CLOSEST to allow to round down and allow us to keep the
set speed.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20221103080043.3033414-1-sean@geanix.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a89b6dec9 ]
The 2.7.0 series of QCN9074's firmware requests 5 segments
of memory instead of 3 (as in the 2.5.0 series).
The first segment (11M) is too large to be kalloc'd in one
go on x86 and requires piecemeal 1MB allocations, as was
the case with the prior public firmware (2.5.0, 15M).
Since f6f92968e1, ath11k will break the memory requests,
but only if there were fewer than 3 segments requested by
the firmware. It seems that 5 segments works fine and
allows QCN9074 to boot on x86 with firmware 2.7.0, so
change things accordingly.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01208-QCAHKSWPL_SILICONZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.16
Signed-off-by: Tyler J. Stachecki <stachecki.tyler@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221022042728.43015-1-stachecki.tyler@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 986d93f55b ]
Shifting signed 32-bit value by 31 bits is undefined, so changing
significant bit to unsigned. The UBSAN warning calltrace like below:
UBSAN: shift-out-of-bounds in kernel/auditfilter.c:179:23
left shift of 1 by 31 places cannot be represented in type 'int'
Call Trace:
<TASK>
dump_stack_lvl+0x7d/0xa5
dump_stack+0x15/0x1b
ubsan_epilogue+0xe/0x4e
__ubsan_handle_shift_out_of_bounds+0x1e7/0x20c
audit_register_class+0x9d/0x137
audit_classes_init+0x4d/0xb8
do_one_initcall+0x76/0x430
kernel_init_freeable+0x3b3/0x422
kernel_init+0x24/0x1e0
ret_from_fork+0x1f/0x30
</TASK>
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
[PM: remove bad 'Fixes' tag as issue predates git, added in v2.6.6-rc1]
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69188df5f6 ]
Fixes a warning that occurs when rc table support is enabled
(IEEE80211_HW_SUPPORTS_RC_TABLE) in mac80211_hwsim and the PS mode
is changed via the exported debugfs attribute.
When the PS mode is changed, a packet is broadcasted via
hwsim_send_nullfunc by creating and transmitting a plain skb with only
header initialized. The ieee80211 rate array in the control buffer is
zero-initialized. When ratetbl support is enabled, ieee80211_get_tx_rates
is called for the skb with sta parameter set to NULL and thus no
ratetbl can be used. The final rate array then looks like
[-1,0; 0,0; 0,0; 0,0] which causes the warning in ieee80211_get_tx_rate.
The issue is fixed by setting the count of the first rate with idx '0'
to 1 and hence ieee80211_get_tx_rates won't overwrite it with idx '-1'.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50b2e87114 ]
ieee80211_register_hw free the allocated cipher suites when
registering wiphy fail, and ieee80211_free_hw will re-free it.
set wiphy_ciphers_allocated to false after freeing allocated
cipher suites.
Signed-off-by: taozhang <taozhang@bestechnic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa1d627207 ]
Prefer using kcalloc(a, b) over kzalloc(a * b) as this improves
semantics since kcalloc is intended for allocating an array of memory.
Signed-off-by: Kenneth Lee <klee33@uw.edu>
Reviewed-by: Xiubo Li <xiubli@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Stable-dep-of: 5bd76b8de5 ("ceph: fix NULL pointer dereference for req->r_session")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ce00bb7e9 ]
Since commit 1da52815d5 ("binder: fix alloc->vma_vm_mm null-ptr
dereference") binder caches a pointer to the current->mm during open().
This fixes a null-ptr dereference reported by syzkaller. Unfortunately,
it also opens the door for a process to update its mm after the open(),
(e.g. via execve) making the cached alloc->mm pointer invalid.
Things get worse when the process continues to mmap() a vma. From this
point forward, binder will attempt to find this vma using an obsolete
alloc->mm reference. Such as in binder_update_page_range(), where the
wrong vma is obtained via vma_lookup(), yet binder proceeds to happily
insert new pages into it.
To avoid this issue fail the ->mmap() callback if we detect a mismatch
between the vma->vm_mm and the original alloc->mm pointer. This prevents
alloc->vm_addr from getting set, so that any subsequent vma_lookup()
calls fail as expected.
Fixes: 1da52815d5 ("binder: fix alloc->vma_vm_mm null-ptr dereference")
Reported-by: Jann Horn <jannh@google.com>
Cc: <stable@vger.kernel.org> # 5.15+
Signed-off-by: Carlos Llamas <cmllamas@google.com>
Acked-by: Todd Kjos <tkjos@google.com>
Link: https://lore.kernel.org/r/20221104231235.348958-1-cmllamas@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e586641c9 ]
We will only track the uppest parent snapshot realm from which we
need to rebuild the snapshot contexts _downward_ in hierarchy. For
all the others having no new snapshot we will do nothing.
This fix will avoid calling ceph_queue_cap_snap() on some inodes
inappropriately. For example, with the code in mainline, suppose there
are 2 directory hierarchies (with 6 directories total), like this:
/dir_X1/dir_X2/dir_X3/
/dir_Y1/dir_Y2/dir_Y3/
Firstly, make a snapshot under /dir_X1/dir_X2/.snap/snap_X2, then make a
root snapshot under /.snap/root_snap. Every time we make snapshots under
/dir_Y1/..., the kclient will always try to rebuild the snap context for
snap_X2 realm and finally will always try to queue cap snaps for dir_Y2
and dir_Y3, which makes no sense.
That's because the snap_X2's seq is 2 and root_snap's seq is 3. So when
creating a new snapshot under /dir_Y1/... the new seq will be 4, and
the mds will send the kclient a snapshot backtrace in _downward_
order: seqs 4, 3.
When ceph_update_snap_trace() is called, it will always rebuild the from
the last realm, that's the root_snap. So later when rebuilding the snap
context, the current logic will always cause it to rebuild the snap_X2
realm and then try to queue cap snaps for all the inodes related in that
realm, even though it's not necessary.
This is accompanied by a lot of these sorts of dout messages:
"ceph: queue_cap_snap 00000000a42b796b nothing dirty|writing"
Fix the logic to avoid this situation.
Also, the 'invalidate' word is not precise here. In actuality, it will
cause a rebuild of the existing snapshot contexts or just build
non-existent ones. Rename it to 'rebuild_snapcs'.
URL: https://tracker.ceph.com/issues/44100
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Stable-dep-of: 51884d153f ("ceph: avoid putting the realm twice when decoding snaps fails")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc19fa63ad ]
The ms5611 passes &indio_dev->dev as a parameter to all its IO callbacks
only to directly cast the struct device back to struct iio_dev. And the
struct iio_dev is then only used to get the drivers state struct.
Simplify this a bit by passing the state struct directly. This makes it a
bit easier to follow what the code is doing.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211020142110.7060-1-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Stable-dep-of: 17f442e7e4 ("iio: pressure: ms5611: fixed value compensation bug")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac9b57d4e1 ]
Kingston SSDs do support NVMe Write_Zeroes cmd but take long time to
process. The firmware version is locked by these SSDs, we can not expect
firmware improvement, so disable Write_Zeroes cmd.
Signed-off-by: Xander Li <xander_li@kingston.com.tw>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Stable-dep-of: 8d6e38f636 ("nvme-pci: add NVME_QUIRK_BOGUS_NID for Netac NV7000")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 41f38043f8 ]
The Micron MTFDKBA2T0TFH device reports the same subsysem NQN for
all devices. Add a quick to ignore it.
Signed-off-by: Leo Savernik <l.savernik@aon.at>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Stable-dep-of: d5ceb4d1c5 ("nvme-pci: add NVME_QUIRK_BOGUS_NID for Micron Nitro")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5954acbacb ]
Current dual mode adaptor ("DP++") detection code assumes that all
adaptors support i2c sub-addressing for read operations from the
DP-HDMI adaptor ID buffer. It has been observed that multiple
adaptors do not in fact support this, and always return data starting
at register 0. On affected adaptors, the code fails to read the proper
registers that would identify the device as a type 2 adaptor, and
handles those as type 1, limiting the TMDS clock to 165MHz, even if
the according register would announce a higher TMDS clock.
Fix this by always reading the ID buffer starting from offset 0, and
discarding any bytes before the actual offset of interest.
We tried finding authoritative documentation on whether or not this is
allowed behaviour, but since all the official VESA docs are paywalled,
the best we could come up with was the spec sheet for Texas Instruments'
SNx5DP149 chip family.[1] It explicitly mentions that sub-addressing is
supported for register writes, but *not* for reads (See NOTE in
section 8.5.3). Unless TI openly decided to violate the VESA spec, one
could take that as a hint that sub-addressing is in fact not mandated
by VESA.
The other two adaptors affected used the PS8409(A) and the LT8611,
according to the data returned from their ID buffers.
[1] https://www.ti.com/lit/ds/symlink/sn75dp149.pdf
Cc: stable@vger.kernel.org
Signed-off-by: Simon Rettberg <simon.rettberg@rz.uni-freiburg.de>
Reviewed-by: Rafael Gieschke <rafael.gieschke@rz.uni-freiburg.de>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221006113314.41101987@computer
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e20e81a24a ]
While the ATA specification states that a device should return command
aborted for all commands queued after the device has entered error state,
since ATA only keeps the sense data for the latest command (in non-NCQ
case), we really don't want to send block layer commands to the device
after it has entered error state. (Only ATA EH commands should be sent,
to read the sense data etc.)
Currently, scsi_queue_rq() will check if scsi_host_in_recovery()
(state is SHOST_RECOVERY), and if so, it will _not_ issue a command via:
scsi_dispatch_cmd() -> host->hostt->queuecommand() (ata_scsi_queuecmd())
-> __ata_scsi_queuecmd() -> ata_scsi_translate() -> ata_qc_issue()
Before commit e494f6a728 ("[SCSI] improved eh timeout handler"),
when receiving a TFES error IRQ, the call chain looked like this:
ahci_error_intr() -> ata_port_abort() -> ata_do_link_abort() ->
ata_qc_complete() -> ata_qc_schedule_eh() -> blk_abort_request() ->
blk_rq_timed_out() -> q->rq_timed_out_fn() (scsi_times_out()) ->
scsi_eh_scmd_add() -> scsi_host_set_state(shost, SHOST_RECOVERY)
Which meant that as soon as an error IRQ was serviced, SHOST_RECOVERY
would be set.
However, after commit e494f6a728 ("[SCSI] improved eh timeout handler"),
scsi_times_out() will instead call scsi_abort_command() which will queue
delayed work, and the worker function scmd_eh_abort_handler() will call
scsi_eh_scmd_add(), which calls scsi_host_set_state(shost, SHOST_RECOVERY).
So now, after the TFES error IRQ has been serviced, we need to wait for
the SCSI workqueue to run its work before SHOST_RECOVERY gets set.
It is worth noting that, even before commit e494f6a728 ("[SCSI] improved
eh timeout handler"), we could receive an error IRQ from the time when
scsi_queue_rq() checks scsi_host_in_recovery(), to the time when
ata_scsi_queuecmd() is actually called.
In order to handle both the delayed setting of SHOST_RECOVERY and the
window where we can receive an error IRQ, add a check against
ATA_PFLAG_EH_PENDING (which gets set when servicing the error IRQ),
inside ata_scsi_queuecmd() itself, while holding the ap->lock.
(Since the ap->lock is held while servicing IRQs.)
Fixes: e494f6a728 ("[SCSI] improved eh timeout handler")
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Tested-by: John Garry <john.g.garry@oracle.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84eac327af ]
This patch cleans up the code of __ata_scsi_queuecmd(). Since each
branch of the "if" condition check that scmd->cmd_len is not zero, move
this check out of the "if" to simplify the conditions being checked in
the "else" branch.
While at it, avoid the if-else-if-else structure using if-else if
structure and remove the redundant rc local variable.
This patch does not change the function logic.
Signed-off-by: Wenchao Hao <haowenchao@huawei.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Stable-dep-of: e20e81a24a ("ata: libata-core: do not issue non-internal commands once EH is pending")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1dcdf5f5b2 ]
If the tlink setup failed, lost to put the connections, then
the module refcnt leak since the cifsd kthread not exit.
Also leak the fscache info, and for next mount with fsc, it will
print the follow errors:
CIFS: Cache volume key already in use (cifs,127.0.0.1:445,TEST)
Let's check the result of tlink setup, and do some cleanup.
Fixes: 56c762eb9b ("cifs: Refactor out cifs_mount()")
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Zhang Xiaoxu <zhangxiaoxu5@huawei.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c88f7dcd6d ]
Mounting a dfs link that has nested links was already supported at
mount(2), so make it work over reconnect as well.
Make the following case work:
* mount //root/dfs/link /mnt -o ...
- final share: /server/share
* in server settings
- change target folder of /root/dfs/link3 to /server/share2
- change target folder of /root/dfs/link2 to /root/dfs/link3
- change target folder of /root/dfs/link to /root/dfs/link2
* mount -o remount,... /mnt
- refresh all dfs referrals
- mark current connection for failover
- cifs_reconnect() reconnects to root server
- tree_connect()
* checks that /root/dfs/link2 is a link, then chase it
* checks that root/dfs/link3 is a link, then chase it
* finally tree connect to /server/share2
If the mounted share is no longer accessible and a reconnect had been
triggered, the client will retry it from both last referral
path (/root/dfs/link3) and original referral path (/root/dfs/link).
Any new referral paths found while chasing dfs links over reconnect,
it will be updated to TCP_Server_Info::leaf_fullpath, accordingly.
Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
Stable-dep-of: 1dcdf5f5b2 ("cifs: Fix connections leak when tlink setup failed")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bbcce36804 ]
Make two separate functions that handle dfs and non-dfs reconnect
logics since cifs_reconnect() became way too complex to handle both.
While at it, add some documentation.
Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Reviewed-by: Shyam Prasad N <sprasad@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Stable-dep-of: 1dcdf5f5b2 ("cifs: Fix connections leak when tlink setup failed")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43b459aa5e ]
Create cifs_mark_tcp_ses_conns_for_reconnect() helper to mark all
sessions and tcons for reconnect when reconnecting tcp server.
Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Reviewed-by: Shyam Prasad N <sprasad@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Stable-dep-of: 1dcdf5f5b2 ("cifs: Fix connections leak when tlink setup failed")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f201ae14a ]
A crash was reported by Zhen Chen:
list_del corruption, ffffa035ddf01c18->next is NULL
WARNING: CPU: 1 PID: 250682 at lib/list_debug.c:49 __list_del_entry_valid+0x59/0xe0
RIP: 0010:__list_del_entry_valid+0x59/0xe0
Call Trace:
sctp_sched_dequeue_common+0x17/0x70 [sctp]
sctp_sched_fcfs_dequeue+0x37/0x50 [sctp]
sctp_outq_flush_data+0x85/0x360 [sctp]
sctp_outq_uncork+0x77/0xa0 [sctp]
sctp_cmd_interpreter.constprop.0+0x164/0x1450 [sctp]
sctp_side_effects+0x37/0xe0 [sctp]
sctp_do_sm+0xd0/0x230 [sctp]
sctp_primitive_SEND+0x2f/0x40 [sctp]
sctp_sendmsg_to_asoc+0x3fa/0x5c0 [sctp]
sctp_sendmsg+0x3d5/0x440 [sctp]
sock_sendmsg+0x5b/0x70
and in sctp_sched_fcfs_dequeue() it dequeued a chunk from stream
out_curr outq while this outq was empty.
Normally stream->out_curr must be set to NULL once all frag chunks of
current msg are dequeued, as we can see in sctp_sched_dequeue_done().
However, in sctp_prsctp_prune_unsent() as it is not a proper dequeue,
sctp_sched_dequeue_done() is not called to do this.
This patch is to fix it by simply setting out_curr to NULL when the
last frag chunk of current msg is dequeued from out_curr stream in
sctp_prsctp_prune_unsent().
Fixes: 5bbbbe32a4 ("sctp: introduce stream scheduler foundations")
Reported-by: Zhen Chen <chenzhen126@huawei.com>
Tested-by: Caowangbao <caowangbao@huawei.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f0b773210 ]
Since commit 5bbbbe32a4 ("sctp: introduce stream scheduler foundations"),
sctp_stream_outq_migrate() has been called in sctp_stream_init/update to
removes those chunks to streams higher than the new max. There is no longer
need to do such check in sctp_prsctp_prune_unsent().
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 2f201ae14a ("sctp: clear out_curr if all frag chunks of current msg are pruned")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 76bad3f887 ]
lpuart_global_reset() shouldn't break the on-going transmit engine, need
to recover the on-going data transfer after reset.
This can help earlycon here, since commit 60f361722a ("serial:
fsl_lpuart: Reset prior to registration") moved lpuart_global_reset()
before uart_add_one_port(), earlycon is writing during global reset,
as global reset will disable the TX and clear the baud rate register,
which caused the earlycon cannot work any more after reset, needs to
restore the baud rate and re-enable the transmitter to recover the
earlycon write.
Also move the lpuart_global_reset() down, then we can reuse the
lpuart32_tx_empty() without declaration.
Fixes: bd5305dcab ("tty: serial: fsl_lpuart: do software reset for imx7ulp and imx8qxp")
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20221024085844.22786-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a564338a2 ]
When CONFIG_PM=N, pm_runtime_put_sync() returns -ENOSYS
which breaks the probe function of these drivers.
Other users of pm_runtime_put_sync() typically don't check
the return value. In order to keep the program flow as
intended, check for -ENOSYS.
This commit is similar to commit 0434d3f (omap-mailbox.c).
Fixes: cab04ab590 ("ASoC: fsl_asrc: Don't use devm_regmap_init_mmio_clk")
Fixes: 203773e393 ("ASoC: fsl_esai: Don't use devm_regmap_init_mmio_clk")
Fixes: 2277e7e36b ("ASoC: fsl_sai: Don't use devm_regmap_init_mmio_clk")
Signed-off-by: Maarten Zanders <maarten.zanders@mind.be>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20221028141129.100702-1-maarten.zanders@mind.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 36a4d82ddd upstream.
Kernel iterates over ATTR_RECORDs in mft record in ntfs_attr_find(). To
ensure access on these ATTR_RECORDs are within bounds, kernel will do some
checking during iteration.
The problem is that during checking whether ATTR_RECORD's name is within
bounds, kernel will dereferences the ATTR_RECORD name_offset field, before
checking this ATTR_RECORD strcture is within bounds. This problem may
result out-of-bounds read in ntfs_attr_find(), reported by Syzkaller:
==================================================================
BUG: KASAN: use-after-free in ntfs_attr_find+0xc02/0xce0 fs/ntfs/attrib.c:597
Read of size 2 at addr ffff88807e352009 by task syz-executor153/3607
[...]
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
print_address_description mm/kasan/report.c:317 [inline]
print_report.cold+0x2ba/0x719 mm/kasan/report.c:433
kasan_report+0xb1/0x1e0 mm/kasan/report.c:495
ntfs_attr_find+0xc02/0xce0 fs/ntfs/attrib.c:597
ntfs_attr_lookup+0x1056/0x2070 fs/ntfs/attrib.c:1193
ntfs_read_inode_mount+0x89a/0x2580 fs/ntfs/inode.c:1845
ntfs_fill_super+0x1799/0x9320 fs/ntfs/super.c:2854
mount_bdev+0x34d/0x410 fs/super.c:1400
legacy_get_tree+0x105/0x220 fs/fs_context.c:610
vfs_get_tree+0x89/0x2f0 fs/super.c:1530
do_new_mount fs/namespace.c:3040 [inline]
path_mount+0x1326/0x1e20 fs/namespace.c:3370
do_mount fs/namespace.c:3383 [inline]
__do_sys_mount fs/namespace.c:3591 [inline]
__se_sys_mount fs/namespace.c:3568 [inline]
__x64_sys_mount+0x27f/0x300 fs/namespace.c:3568
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
[...]
</TASK>
The buggy address belongs to the physical page:
page:ffffea0001f8d400 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x7e350
head:ffffea0001f8d400 order:3 compound_mapcount:0 compound_pincount:0
flags: 0xfff00000010200(slab|head|node=0|zone=1|lastcpupid=0x7ff)
raw: 00fff00000010200 0000000000000000 dead000000000122 ffff888011842140
raw: 0000000000000000 0000000000040004 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff88807e351f00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff88807e351f80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff88807e352000: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff88807e352080: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff88807e352100: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
==================================================================
This patch solves it by moving the ATTR_RECORD strcture's bounds checking
earlier, then checking whether ATTR_RECORD's name is within bounds.
What's more, this patch also add some comments to improve its
maintainability.
Link: https://lkml.kernel.org/r/20220831160935.3409-3-yin31149@gmail.com
Link: https://lore.kernel.org/all/1636796c-c85e-7f47-e96f-e074fee3c7d3@huawei.com/
Link: https://groups.google.com/g/syzkaller-bugs/c/t_XdeKPGTR4/m/LECAuIGcBgAJ
Signed-off-by: chenxiaosong (A) <chenxiaosong2@huawei.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hawkins Jiawei <yin31149@gmail.com>
Reported-by: syzbot+5f8dcabe4a3b2c51c607@syzkaller.appspotmail.com
Tested-by: syzbot+5f8dcabe4a3b2c51c607@syzkaller.appspotmail.com
Cc: Anton Altaparmakov <anton@tuxera.com>
Cc: syzkaller-bugs <syzkaller-bugs@googlegroups.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d85a1bec8e upstream.
Patch series "ntfs: fix bugs about Attribute", v2.
This patchset fixes three bugs relative to Attribute in record:
Patch 1 adds a sanity check to ensure that, attrs_offset field in first
mft record loading from disk is within bounds.
Patch 2 moves the ATTR_RECORD's bounds checking earlier, to avoid
dereferencing ATTR_RECORD before checking this ATTR_RECORD is within
bounds.
Patch 3 adds an overflow checking to avoid possible forever loop in
ntfs_attr_find().
Without patch 1 and patch 2, the kernel triggersa KASAN use-after-free
detection as reported by Syzkaller.
Although one of patch 1 or patch 2 can fix this, we still need both of
them. Because patch 1 fixes the root cause, and patch 2 not only fixes
the direct cause, but also fixes the potential out-of-bounds bug.
This patch (of 3):
Syzkaller reported use-after-free read as follows:
==================================================================
BUG: KASAN: use-after-free in ntfs_attr_find+0xc02/0xce0 fs/ntfs/attrib.c:597
Read of size 2 at addr ffff88807e352009 by task syz-executor153/3607
[...]
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
print_address_description mm/kasan/report.c:317 [inline]
print_report.cold+0x2ba/0x719 mm/kasan/report.c:433
kasan_report+0xb1/0x1e0 mm/kasan/report.c:495
ntfs_attr_find+0xc02/0xce0 fs/ntfs/attrib.c:597
ntfs_attr_lookup+0x1056/0x2070 fs/ntfs/attrib.c:1193
ntfs_read_inode_mount+0x89a/0x2580 fs/ntfs/inode.c:1845
ntfs_fill_super+0x1799/0x9320 fs/ntfs/super.c:2854
mount_bdev+0x34d/0x410 fs/super.c:1400
legacy_get_tree+0x105/0x220 fs/fs_context.c:610
vfs_get_tree+0x89/0x2f0 fs/super.c:1530
do_new_mount fs/namespace.c:3040 [inline]
path_mount+0x1326/0x1e20 fs/namespace.c:3370
do_mount fs/namespace.c:3383 [inline]
__do_sys_mount fs/namespace.c:3591 [inline]
__se_sys_mount fs/namespace.c:3568 [inline]
__x64_sys_mount+0x27f/0x300 fs/namespace.c:3568
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
[...]
</TASK>
The buggy address belongs to the physical page:
page:ffffea0001f8d400 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x7e350
head:ffffea0001f8d400 order:3 compound_mapcount:0 compound_pincount:0
flags: 0xfff00000010200(slab|head|node=0|zone=1|lastcpupid=0x7ff)
raw: 00fff00000010200 0000000000000000 dead000000000122 ffff888011842140
raw: 0000000000000000 0000000000040004 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff88807e351f00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff88807e351f80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff88807e352000: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff88807e352080: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff88807e352100: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
==================================================================
Kernel will loads $MFT/$DATA's first mft record in
ntfs_read_inode_mount().
Yet the problem is that after loading, kernel doesn't check whether
attrs_offset field is a valid value.
To be more specific, if attrs_offset field is larger than bytes_allocated
field, then it may trigger the out-of-bounds read bug(reported as
use-after-free bug) in ntfs_attr_find(), when kernel tries to access the
corresponding mft record's attribute.
This patch solves it by adding the sanity check between attrs_offset field
and bytes_allocated field, after loading the first mft record.
Link: https://lkml.kernel.org/r/20220831160935.3409-1-yin31149@gmail.com
Link: https://lkml.kernel.org/r/20220831160935.3409-2-yin31149@gmail.com
Signed-off-by: Hawkins Jiawei <yin31149@gmail.com>
Cc: Anton Altaparmakov <anton@tuxera.com>
Cc: ChenXiaoSong <chenxiaosong2@huawei.com>
Cc: syzkaller-bugs <syzkaller-bugs@googlegroups.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e3e6e1d16a upstream.
Syzkaller reports buffer overflow false positive as follows:
------------[ cut here ]------------
memcpy: detected field-spanning write (size 8) of single field
"&compat_event->pointer" at net/wireless/wext-core.c:623 (size 4)
WARNING: CPU: 0 PID: 3607 at net/wireless/wext-core.c:623
wireless_send_event+0xab5/0xca0 net/wireless/wext-core.c:623
Modules linked in:
CPU: 1 PID: 3607 Comm: syz-executor659 Not tainted
6.0.0-rc6-next-20220921-syzkaller #0
[...]
Call Trace:
<TASK>
ioctl_standard_call+0x155/0x1f0 net/wireless/wext-core.c:1022
wireless_process_ioctl+0xc8/0x4c0 net/wireless/wext-core.c:955
wext_ioctl_dispatch net/wireless/wext-core.c:988 [inline]
wext_ioctl_dispatch net/wireless/wext-core.c:976 [inline]
wext_handle_ioctl+0x26b/0x280 net/wireless/wext-core.c:1049
sock_ioctl+0x285/0x640 net/socket.c:1220
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:870 [inline]
__se_sys_ioctl fs/ioctl.c:856 [inline]
__x64_sys_ioctl+0x193/0x200 fs/ioctl.c:856
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
[...]
</TASK>
Wireless events will be sent on the appropriate channels in
wireless_send_event(). Different wireless events may have different
payload structure and size, so kernel uses **len** and **cmd** field
in struct __compat_iw_event as wireless event common LCP part, uses
**pointer** as a label to mark the position of remaining different part.
Yet the problem is that, **pointer** is a compat_caddr_t type, which may
be smaller than the relative structure at the same position. So during
wireless_send_event() tries to parse the wireless events payload, it may
trigger the memcpy() run-time destination buffer bounds checking when the
relative structure's data is copied to the position marked by **pointer**.
This patch solves it by introducing flexible-array field **ptr_bytes**,
to mark the position of the wireless events remaining part next to
LCP part. What's more, this patch also adds **ptr_len** variable in
wireless_send_event() to improve its maintainability.
Reported-and-tested-by: syzbot+473754e5af963cf014cf@syzkaller.appspotmail.com
Link: https://lore.kernel.org/all/00000000000070db2005e95a5984@google.com/
Suggested-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Hawkins Jiawei <yin31149@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef575281b2 upstream.
syzbot is reporting hung task at p9_fd_close() [1], for p9_mux_poll_stop()
from p9_conn_destroy() from p9_fd_close() is failing to interrupt already
started kernel_read() from p9_fd_read() from p9_read_work() and/or
kernel_write() from p9_fd_write() from p9_write_work() requests.
Since p9_socket_open() sets O_NONBLOCK flag, p9_mux_poll_stop() does not
need to interrupt kernel_read()/kernel_write(). However, since p9_fd_open()
does not set O_NONBLOCK flag, but pipe blocks unless signal is pending,
p9_mux_poll_stop() needs to interrupt kernel_read()/kernel_write() when
the file descriptor refers to a pipe. In other words, pipe file descriptor
needs to be handled as if socket file descriptor.
We somehow need to interrupt kernel_read()/kernel_write() on pipes.
A minimal change, which this patch is doing, is to set O_NONBLOCK flag
from p9_fd_open(), for O_NONBLOCK flag does not affect reading/writing
of regular files. But this approach changes O_NONBLOCK flag on userspace-
supplied file descriptors (which might break userspace programs), and
O_NONBLOCK flag could be changed by userspace. It would be possible to set
O_NONBLOCK flag every time p9_fd_read()/p9_fd_write() is invoked, but still
remains small race window for clearing O_NONBLOCK flag.
If we don't want to manipulate O_NONBLOCK flag, we might be able to
surround kernel_read()/kernel_write() with set_thread_flag(TIF_SIGPENDING)
and recalc_sigpending(). Since p9_read_work()/p9_write_work() works are
processed by kernel threads which process global system_wq workqueue,
signals could not be delivered from remote threads when p9_mux_poll_stop()
from p9_conn_destroy() from p9_fd_close() is called. Therefore, calling
set_thread_flag(TIF_SIGPENDING)/recalc_sigpending() every time would be
needed if we count on signals for making kernel_read()/kernel_write()
non-blocking.
Link: https://lkml.kernel.org/r/345de429-a88b-7097-d177-adecf9fed342@I-love.SAKURA.ne.jp
Link: https://syzkaller.appspot.com/bug?extid=8b41a1365f1106fd0f33 [1]
Reported-by: syzbot <syzbot+8b41a1365f1106fd0f33@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Tested-by: syzbot <syzbot+8b41a1365f1106fd0f33@syzkaller.appspotmail.com>
Reviewed-by: Christian Schoenebeck <linux_oss@crudebyte.com>
[Dominique: add comment at Christian's suggestion]
Signed-off-by: Dominique Martinet <asmadeus@codewreck.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 204c0300c4 upstream.
Switch from strlcpy to strscpy and make sure that @count is the size of
the smaller of the source and destination buffers. This prevents
reading beyond the end of the source buffer when the source string isn't
null terminated.
Found by a modified version of syzkaller.
Suggested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 670f8ce56d upstream.
Fuzzers like to scribble over sb_bsize_shift but in reality it's very
unlikely that this field would be corrupted on its own. Nevertheless it
should be checked to avoid the possibility of messy mount errors due to
bad calculations. It's always a fixed value based on the block size so
we can just check that it's the expected value.
Tested with:
mkfs.gfs2 -O -p lock_nolock /dev/vdb
for i in 0 -1 64 65 32 33; do
gfs2_edit -p sb field sb_bsize_shift $i /dev/vdb
mount /dev/vdb /mnt/test && umount /mnt/test
done
Before this patch we get a withdraw after
[ 76.413681] gfs2: fsid=loop0.0: fatal: invalid metadata block
[ 76.413681] bh = 19 (type: exp=5, found=4)
[ 76.413681] function = gfs2_meta_buffer, file = fs/gfs2/meta_io.c, line = 492
and with UBSAN configured we also get complaints like
[ 76.373395] UBSAN: shift-out-of-bounds in fs/gfs2/ops_fstype.c:295:19
[ 76.373815] shift exponent 4294967287 is too large for 64-bit type 'long unsigned int'
After the patch, these complaints don't appear, mount fails immediately
and we get an explanation in dmesg.
Reported-by: syzbot+dcf33a7aae997956fe06@syzkaller.appspotmail.com
Signed-off-by: Andrew Price <anprice@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5121197ecc upstream.
sk->sk_receive_queue is protected by skb queue lock, but for KCM
sockets its RX path takes mux->rx_lock to protect more than just
skb queue. However, kcm_recvmsg() still only grabs the skb queue
lock, so race conditions still exist.
We can teach kcm_recvmsg() to grab mux->rx_lock too but this would
introduce a potential performance regression as struct kcm_mux can
be shared by multiple KCM sockets.
So we have to enforce skb queue lock in requeue_rx_msgs() and handle
skb peek case carefully in kcm_wait_data(). Fortunately,
skb_recv_datagram() already handles it nicely and is widely used by
other sockets, we can just switch to skb_recv_datagram() after
getting rid of the unnecessary sock lock in kcm_recvmsg() and
kcm_splice_read(). Side note: SOCK_DONE is not used by KCM sockets,
so it is safe to get rid of this check too.
I ran the original syzbot reproducer for 30 min without seeing any
issue.
Fixes: ab7ac4eb98 ("kcm: Kernel Connection Multiplexor module")
Reported-by: syzbot+278279efdd2730dd14bf@syzkaller.appspotmail.com
Reported-by: shaozhengchao <shaozhengchao@huawei.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Link: https://lore.kernel.org/r/20221114005119.597905-1-xiyou.wangcong@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b64085b000 upstream.
macvlan should enforce a minimal mtu of 68, even at link creation.
This patch avoids the current behavior (which could lead to crashes
in ipv6 stack if the link is brought up)
$ ip link add macvlan1 link eno1 mtu 8 type macvlan # This should fail !
$ ip link sh dev macvlan1
5: macvlan1@eno1: <BROADCAST,MULTICAST> mtu 8 qdisc noop
state DOWN mode DEFAULT group default qlen 1000
link/ether 02:47:6c:24:74:82 brd ff:ff:ff:ff:ff:ff
$ ip link set macvlan1 mtu 67
Error: mtu less than device minimum.
$ ip link set macvlan1 mtu 68
$ ip link set macvlan1 mtu 8
Error: mtu less than device minimum.
Fixes: 91572088e3 ("net: use core MTU range checking in core net infra")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5dd7caf0bd ]
In __unregister_kprobe_top(), if the currently unregistered probe has
post_handler but other child probes of the aggrprobe do not have
post_handler, the post_handler of the aggrprobe is cleared. If this is
a ftrace-based probe, there is a problem. In later calls to
disarm_kprobe(), we will use kprobe_ftrace_ops because post_handler is
NULL. But we're armed with kprobe_ipmodify_ops. This triggers a WARN in
__disarm_kprobe_ftrace() and may even cause use-after-free:
Failed to disarm kprobe-ftrace at kernel_clone+0x0/0x3c0 (error -2)
WARNING: CPU: 5 PID: 137 at kernel/kprobes.c:1135 __disarm_kprobe_ftrace.isra.21+0xcf/0xe0
Modules linked in: testKprobe_007(-)
CPU: 5 PID: 137 Comm: rmmod Not tainted 6.1.0-rc4-dirty #18
[...]
Call Trace:
<TASK>
__disable_kprobe+0xcd/0xe0
__unregister_kprobe_top+0x12/0x150
? mutex_lock+0xe/0x30
unregister_kprobes.part.23+0x31/0xa0
unregister_kprobe+0x32/0x40
__x64_sys_delete_module+0x15e/0x260
? do_user_addr_fault+0x2cd/0x6b0
do_syscall_64+0x3a/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
[...]
For the kprobe-on-ftrace case, we keep the post_handler setting to
identify this aggrprobe armed with kprobe_ipmodify_ops. This way we
can disarm it correctly.
Link: https://lore.kernel.org/all/20221112070000.35299-1-lihuafei1@huawei.com/
Fixes: 0bc11ed5ab ("kprobes: Allow kprobes coexist with livepatch")
Reported-by: Zhao Gongyi <zhaogongyi@huawei.com>
Suggested-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Li Huafei <lihuafei1@huawei.com>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc68e428d4 ]
If device_register() fails in tcm_loop_setup_hba_bus(), the name allocated
by dev_set_name() need be freed. As comment of device_register() says, it
should use put_device() to give up the reference in the error path. So fix
this by calling put_device(), then the name can be freed in kobject_cleanup().
The 'tl_hba' will be freed in tcm_loop_release_adapter(), so it don't need
goto error label in this case.
Fixes: 3703b2c5d0 ("[SCSI] tcm_loop: Add multi-fabric Linux/SCSI LLD fabric module")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221115015042.3652261-1-yangyingliang@huawei.com
Reviewed-by: Mike Christie <michael.chritie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58e0be1ef6 ]
kernel test robot reported warnings when build bonding module with
make W=1 O=build_dir ARCH=x86_64 SHELL=/bin/bash drivers/net/bonding/:
from ../drivers/net/bonding/bond_main.c:35:
In function ‘fortify_memcpy_chk’,
inlined from ‘iph_to_flow_copy_v4addrs’ at ../include/net/ip.h:566:2,
inlined from ‘bond_flow_ip’ at ../drivers/net/bonding/bond_main.c:3984:3:
../include/linux/fortify-string.h:413:25: warning: call to ‘__read_overflow2_field’ declared with attribute warning: detected read beyond size of f
ield (2nd parameter); maybe use struct_group()? [-Wattribute-warning]
413 | __read_overflow2_field(q_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In function ‘fortify_memcpy_chk’,
inlined from ‘iph_to_flow_copy_v6addrs’ at ../include/net/ipv6.h:900:2,
inlined from ‘bond_flow_ip’ at ../drivers/net/bonding/bond_main.c:3994:3:
../include/linux/fortify-string.h:413:25: warning: call to ‘__read_overflow2_field’ declared with attribute warning: detected read beyond size of f
ield (2nd parameter); maybe use struct_group()? [-Wattribute-warning]
413 | __read_overflow2_field(q_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
This is because we try to copy the whole ip/ip6 address to the flow_key,
while we only point the to ip/ip6 saddr. Note that since these are UAPI
headers, __struct_group() is used to avoid the compiler warnings.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: c3f8324188 ("net: Add full IPv6 addresses to flow_keys")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://lore.kernel.org/r/20221115142400.1204786-1-liuhangbin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 31029a8b2c ]
The function ring_buffer_nr_dirty_pages() was created to find out how many
pages are filled in the ring buffer. There's two running counters. One is
incremented whenever a new page is touched (pages_touched) and the other
is whenever a page is read (pages_read). The dirty count is the number
touched minus the number read. This is used to determine if a blocked task
should be woken up if the percentage of the ring buffer it is waiting for
is hit.
The problem is that it does not take into account dropped pages (when the
new writes overwrite pages that were not read). And then the dirty pages
will always be greater than the percentage.
This makes the "buffer_percent" file inaccurate, as the number of dirty
pages end up always being larger than the percentage, event when it's not
and this causes user space to be woken up more than it wants to be.
Add a new counter to keep track of lost pages, and include that in the
accounting of dirty pages so that it is actually accurate.
Link: https://lkml.kernel.org/r/20221021123013.55fb6055@gandalf.local.home
Fixes: 2c2b0a78b3 ("ring-buffer: Add percentage of ring buffer full to wake up reader")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb88f96954 ]
To catch missing SIGTRAP we employ a WARN in __perf_event_overflow(),
which fires if pending_sigtrap was already set: returning to user space
without consuming pending_sigtrap, and then having the event fire again
would re-enter the kernel and trigger the WARN.
This, however, seemed to miss the case where some events not associated
with progress in the user space task can fire and the interrupt handler
runs before the IRQ work meant to consume pending_sigtrap (and generate
the SIGTRAP).
syzbot gifted us this stack trace:
| WARNING: CPU: 0 PID: 3607 at kernel/events/core.c:9313 __perf_event_overflow
| Modules linked in:
| CPU: 0 PID: 3607 Comm: syz-executor100 Not tainted 6.1.0-rc2-syzkaller-00073-g88619e77b33d #0
| Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/11/2022
| RIP: 0010:__perf_event_overflow+0x498/0x540 kernel/events/core.c:9313
| <...>
| Call Trace:
| <TASK>
| perf_swevent_hrtimer+0x34f/0x3c0 kernel/events/core.c:10729
| __run_hrtimer kernel/time/hrtimer.c:1685 [inline]
| __hrtimer_run_queues+0x1c6/0xfb0 kernel/time/hrtimer.c:1749
| hrtimer_interrupt+0x31c/0x790 kernel/time/hrtimer.c:1811
| local_apic_timer_interrupt arch/x86/kernel/apic/apic.c:1096 [inline]
| __sysvec_apic_timer_interrupt+0x17c/0x640 arch/x86/kernel/apic/apic.c:1113
| sysvec_apic_timer_interrupt+0x40/0xc0 arch/x86/kernel/apic/apic.c:1107
| asm_sysvec_apic_timer_interrupt+0x16/0x20 arch/x86/include/asm/idtentry.h:649
| <...>
| </TASK>
In this case, syzbot produced a program with event type
PERF_TYPE_SOFTWARE and config PERF_COUNT_SW_CPU_CLOCK. The hrtimer
manages to fire again before the IRQ work got a chance to run, all while
never having returned to user space.
Improve the WARN to check for real progress in user space: approximate
this by storing a 32-bit hash of the current IP into pending_sigtrap,
and if an event fires while pending_sigtrap still matches the previous
IP, we assume no progress (false negatives are possible given we could
return to user space and trigger again on the same IP).
Fixes: ca6c21327c ("perf: Fix missing SIGTRAPs")
Reported-by: syzbot+b8ded3e2e2c6adde4990@syzkaller.appspotmail.com
Signed-off-by: Marco Elver <elver@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20221031093513.3032814-1-elver@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1e866afd4b upstream.
The subsystem reset writes to a register, so we have to ensure the
device state is capable of handling that otherwise the driver may access
unmapped registers. Use the state machine to ensure the subsystem reset
doesn't try to write registers on a device already undergoing this type
of reset.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=214771
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23e085b2de upstream.
The passthrough commands already have this restriction, but the other
operations do not. Require the same capabilities for all users as all of
these operations, which include resets and rescans, can be disruptive.
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e5b0d06d9b upstream.
`struct vmci_event_qp` allocated by qp_notify_peer() contains padding,
which may carry uninitialized data to the userspace, as observed by
KMSAN:
BUG: KMSAN: kernel-infoleak in instrument_copy_to_user ./include/linux/instrumented.h:121
instrument_copy_to_user ./include/linux/instrumented.h:121
_copy_to_user+0x5f/0xb0 lib/usercopy.c:33
copy_to_user ./include/linux/uaccess.h:169
vmci_host_do_receive_datagram drivers/misc/vmw_vmci/vmci_host.c:431
vmci_host_unlocked_ioctl+0x33d/0x43d0 drivers/misc/vmw_vmci/vmci_host.c:925
vfs_ioctl fs/ioctl.c:51
...
Uninit was stored to memory at:
kmemdup+0x74/0xb0 mm/util.c:131
dg_dispatch_as_host drivers/misc/vmw_vmci/vmci_datagram.c:271
vmci_datagram_dispatch+0x4f8/0xfc0 drivers/misc/vmw_vmci/vmci_datagram.c:339
qp_notify_peer+0x19a/0x290 drivers/misc/vmw_vmci/vmci_queue_pair.c:1479
qp_broker_attach drivers/misc/vmw_vmci/vmci_queue_pair.c:1662
qp_broker_alloc+0x2977/0x2f30 drivers/misc/vmw_vmci/vmci_queue_pair.c:1750
vmci_qp_broker_alloc+0x96/0xd0 drivers/misc/vmw_vmci/vmci_queue_pair.c:1940
vmci_host_do_alloc_queuepair drivers/misc/vmw_vmci/vmci_host.c:488
vmci_host_unlocked_ioctl+0x24fd/0x43d0 drivers/misc/vmw_vmci/vmci_host.c:927
...
Local variable ev created at:
qp_notify_peer+0x54/0x290 drivers/misc/vmw_vmci/vmci_queue_pair.c:1456
qp_broker_attach drivers/misc/vmw_vmci/vmci_queue_pair.c:1662
qp_broker_alloc+0x2977/0x2f30 drivers/misc/vmw_vmci/vmci_queue_pair.c:1750
Bytes 28-31 of 48 are uninitialized
Memory access of size 48 starts at ffff888035155e00
Data copied to user address 0000000020000100
Use memset() to prevent the infoleaks.
Also speculatively fix qp_notify_peer_local(), which may suffer from the
same problem.
Reported-by: syzbot+39be4da489ed2493ba25@syzkaller.appspotmail.com
Cc: stable <stable@kernel.org>
Fixes: 06164d2b72 ("VMCI: queue pairs implementation.")
Signed-off-by: Alexander Potapenko <glider@google.com>
Reviewed-by: Vishnu Dasa <vdasa@vmware.com>
Link: https://lore.kernel.org/r/20221104175849.2782567-1-glider@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 39a72dbfe1 upstream.
In mmc_select_voltage(), if there is no full power cycle, the voltage
range selected at the end of the function will be on a single range
(e.g. 3.3V/3.4V). To keep a range around the selected voltage (3.2V/3.4V),
the mask shift should be reduced by 1.
This issue was triggered by using a specific SD-card (Verbatim Premium
16GB UHS-1) on an STM32MP157C-DK2 board. This board cannot do UHS modes
and there is no power cycle. And the card was failing to switch to
high-speed mode. When adding the range 3.2V/3.3V for this card with the
proposed shift change, the card can switch to high-speed mode.
Fixes: ce69d37b7d ("mmc: core: Prevent violation of specs while initializing cards")
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221028073740.7259-1-yann.gautier@foss.st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 65946690ed upstream.
The coreboot_table driver registers a coreboot bus while probing a
"coreboot_table" device representing the coreboot table memory region.
Probing this device (i.e., registering the bus) is a dependency for the
module_init() functions of any driver for this bus (e.g.,
memconsole-coreboot.c / memconsole_driver_init()).
With synchronous probe, this dependency works OK, as the link order in
the Makefile ensures coreboot_table_driver_init() (and thus,
coreboot_table_probe()) completes before a coreboot device driver tries
to add itself to the bus.
With asynchronous probe, however, coreboot_table_probe() may race with
memconsole_driver_init(), and so we're liable to hit one of these two:
1. coreboot_driver_register() eventually hits "[...] the bus was not
initialized.", and the memconsole driver fails to register; or
2. coreboot_driver_register() gets past #1, but still races with
bus_register() and hits some other undefined/crashing behavior (e.g.,
in driver_find() [1])
We can resolve this by registering the bus in our initcall, and only
deferring "device" work (scanning the coreboot memory region and
creating sub-devices) to probe().
[1] Example failure, using 'driver_async_probe=*' kernel command line:
[ 0.114217] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000010
...
[ 0.114307] CPU: 1 PID: 1 Comm: swapper/0 Not tainted 6.1.0-rc1 #63
[ 0.114316] Hardware name: Google Scarlet (DT)
...
[ 0.114488] Call trace:
[ 0.114494] _raw_spin_lock+0x34/0x60
[ 0.114502] kset_find_obj+0x28/0x84
[ 0.114511] driver_find+0x30/0x50
[ 0.114520] driver_register+0x64/0x10c
[ 0.114528] coreboot_driver_register+0x30/0x3c
[ 0.114540] memconsole_driver_init+0x24/0x30
[ 0.114550] do_one_initcall+0x154/0x2e0
[ 0.114560] do_initcall_level+0x134/0x160
[ 0.114571] do_initcalls+0x60/0xa0
[ 0.114579] do_basic_setup+0x28/0x34
[ 0.114588] kernel_init_freeable+0xf8/0x150
[ 0.114596] kernel_init+0x2c/0x12c
[ 0.114607] ret_from_fork+0x10/0x20
[ 0.114624] Code: 5280002b 1100054a b900092a f9800011 (885ffc01)
[ 0.114631] ---[ end trace 0000000000000000 ]---
Fixes: b81e3140e4 ("firmware: coreboot: Make bus registration symmetric")
Cc: <stable@vger.kernel.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20221019180934.1.If29e167d8a4771b0bf4a39c89c6946ed764817b9@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7fc961cf7f upstream.
SRS cap is the hardware cap telling if the hardware IOMMU can support
requests seeking supervisor privilege or not. SRE bit in scalable-mode
PASID table entry is treated as Reserved(0) for implementation not
supporting SRS cap.
Checking SRS cap before setting SRE bit can avoid the non-recoverable
fault of "Non-zero reserved field set in PASID Table Entry" caused by
setting SRE bit while there is no SRS cap support. The fault messages
look like below:
DMAR: DRHD: handling fault status reg 2
DMAR: [DMA Read NO_PASID] Request device [00:0d.0] fault addr 0x1154e1000
[fault reason 0x5a]
SM: Non-zero reserved field set in PASID Table Entry
Fixes: 6f7db75e1c ("iommu/vt-d: Add second level page table interface")
Cc: stable@vger.kernel.org
Signed-off-by: Tina Zhang <tina.zhang@intel.com>
Link: https://lore.kernel.org/r/20221115070346.1112273-1-tina.zhang@intel.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20221116051544.26540-3-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 242b0aaeab upstream.
The A/D bits are preseted for IOVA over first level(FL) usage for both
kernel DMA (i.e, domain typs is IOMMU_DOMAIN_DMA) and user space DMA
usage (i.e., domain type is IOMMU_DOMAIN_UNMANAGED).
Presetting A bit in FL requires to preset the bit in every related paging
entries, including the non-leaf ones. Otherwise, hardware may treat this
as an error. For example, in a case of ECAP_REG.SMPWC==0, DMA faults might
occur with below DMAR fault messages (wrapped for line length) dumped.
DMAR: DRHD: handling fault status reg 2
DMAR: [DMA Read NO_PASID] Request device [aa:00.0] fault addr 0x10c3a6000
[fault reason 0x90]
SM: A/D bit update needed in first-level entry when set up in no snoop
Fixes: 289b3b005c ("iommu/vt-d: Preset A/D bits for user space DMA usage")
Cc: stable@vger.kernel.org
Signed-off-by: Tina Zhang <tina.zhang@intel.com>
Link: https://lore.kernel.org/r/20221113010324.1094483-1-tina.zhang@intel.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20221116051544.26540-2-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0954256e97 upstream.
We used to use the wrong type of integer in 'zfcp_fsf_req_send()' to cache
the FSF request ID when sending a new FSF request. This is used in case the
sending fails and we need to remove the request from our internal hash
table again (so we don't keep an invalid reference and use it when we free
the request again).
In 'zfcp_fsf_req_send()' we used to cache the ID as 'int' (signed and 32
bit wide), but the rest of the zfcp code (and the firmware specification)
handles the ID as 'unsigned long'/'u64' (unsigned and 64 bit wide [s390x
ELF ABI]). For one this has the obvious problem that when the ID grows
past 32 bit (this can happen reasonably fast) it is truncated to 32 bit
when storing it in the cache variable and so doesn't match the original ID
anymore. The second less obvious problem is that even when the original ID
has not yet grown past 32 bit, as soon as the 32nd bit is set in the
original ID (0x80000000 = 2'147'483'648) we will have a mismatch when we
cast it back to 'unsigned long'. As the cached variable is of a signed
type, the compiler will choose a sign-extending instruction to load the 32
bit variable into a 64 bit register (e.g.: 'lgf %r11,188(%r15)'). So once
we pass the cached variable into 'zfcp_reqlist_find_rm()' to remove the
request again all the leading zeros will be flipped to ones to extend the
sign and won't match the original ID anymore (this has been observed in
practice).
If we can't successfully remove the request from the hash table again after
'zfcp_qdio_send()' fails (this happens regularly when zfcp cannot notify
the adapter about new work because the adapter is already gone during
e.g. a ChpID toggle) we will end up with a double free. We unconditionally
free the request in the calling function when 'zfcp_fsf_req_send()' fails,
but because the request is still in the hash table we end up with a stale
memory reference, and once the zfcp adapter is either reset during recovery
or shutdown we end up freeing the same memory twice.
The resulting stack traces vary depending on the kernel and have no direct
correlation to the place where the bug occurs. Here are three examples that
have been seen in practice:
list_del corruption. next->prev should be 00000001b9d13800, but was 00000000dead4ead. (next=00000001bd131a00)
------------[ cut here ]------------
kernel BUG at lib/list_debug.c:62!
monitor event: 0040 ilc:2 [#1] PREEMPT SMP
Modules linked in: ...
CPU: 9 PID: 1617 Comm: zfcperp0.0.1740 Kdump: loaded
Hardware name: ...
Krnl PSW : 0704d00180000000 00000003cbeea1f8 (__list_del_entry_valid+0x98/0x140)
R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:0 AS:3 CC:1 PM:0 RI:0 EA:3
Krnl GPRS: 00000000916d12f1 0000000080000000 000000000000006d 00000003cb665cd6
0000000000000001 0000000000000000 0000000000000000 00000000d28d21e8
00000000d3844000 00000380099efd28 00000001bd131a00 00000001b9d13800
00000000d3290100 0000000000000000 00000003cbeea1f4 00000380099efc70
Krnl Code: 00000003cbeea1e8: c020004f68a7 larl %r2,00000003cc8d7336
00000003cbeea1ee: c0e50027fd65 brasl %r14,00000003cc3e9cb8
#00000003cbeea1f4: af000000 mc 0,0
>00000003cbeea1f8: c02000920440 larl %r2,00000003cd12aa78
00000003cbeea1fe: c0e500289c25 brasl %r14,00000003cc3fda48
00000003cbeea204: b9040043 lgr %r4,%r3
00000003cbeea208: b9040051 lgr %r5,%r1
00000003cbeea20c: b9040032 lgr %r3,%r2
Call Trace:
[<00000003cbeea1f8>] __list_del_entry_valid+0x98/0x140
([<00000003cbeea1f4>] __list_del_entry_valid+0x94/0x140)
[<000003ff7ff502fe>] zfcp_fsf_req_dismiss_all+0xde/0x150 [zfcp]
[<000003ff7ff49cd0>] zfcp_erp_strategy_do_action+0x160/0x280 [zfcp]
[<000003ff7ff4a22e>] zfcp_erp_strategy+0x21e/0xca0 [zfcp]
[<000003ff7ff4ad34>] zfcp_erp_thread+0x84/0x1a0 [zfcp]
[<00000003cb5eece8>] kthread+0x138/0x150
[<00000003cb557f3c>] __ret_from_fork+0x3c/0x60
[<00000003cc4172ea>] ret_from_fork+0xa/0x40
INFO: lockdep is turned off.
Last Breaking-Event-Address:
[<00000003cc3e9d04>] _printk+0x4c/0x58
Kernel panic - not syncing: Fatal exception: panic_on_oops
or:
Unable to handle kernel pointer dereference in virtual kernel address space
Failing address: 6b6b6b6b6b6b6000 TEID: 6b6b6b6b6b6b6803
Fault in home space mode while using kernel ASCE.
AS:0000000063b10007 R3:0000000000000024
Oops: 0038 ilc:3 [#1] SMP
Modules linked in: ...
CPU: 10 PID: 0 Comm: swapper/10 Kdump: loaded
Hardware name: ...
Krnl PSW : 0404d00180000000 000003ff7febaf8e (zfcp_fsf_reqid_check+0x86/0x158 [zfcp])
R:0 T:1 IO:0 EX:0 Key:0 M:1 W:0 P:0 AS:3 CC:1 PM:0 RI:0 EA:3
Krnl GPRS: 5a6f1cfa89c49ac3 00000000aff2c4c8 6b6b6b6b6b6b6b6b 00000000000002a8
0000000000000000 0000000000000055 0000000000000000 00000000a8515800
0700000000000000 00000000a6e14500 00000000aff2c000 000000008003c44c
000000008093c700 0000000000000010 00000380009ebba8 00000380009ebb48
Krnl Code: 000003ff7febaf7e: a7f4003d brc 15,000003ff7febaff8
000003ff7febaf82: e32020000004 lg %r2,0(%r2)
#000003ff7febaf88: ec2100388064 cgrj %r2,%r1,8,000003ff7febaff8
>000003ff7febaf8e: e3b020100020 cg %r11,16(%r2)
000003ff7febaf94: a774fff7 brc 7,000003ff7febaf82
000003ff7febaf98: ec280030007c cgij %r2,0,8,000003ff7febaff8
000003ff7febaf9e: e31020080004 lg %r1,8(%r2)
000003ff7febafa4: e33020000004 lg %r3,0(%r2)
Call Trace:
[<000003ff7febaf8e>] zfcp_fsf_reqid_check+0x86/0x158 [zfcp]
[<000003ff7febbdbc>] zfcp_qdio_int_resp+0x6c/0x170 [zfcp]
[<000003ff7febbf90>] zfcp_qdio_irq_tasklet+0xd0/0x108 [zfcp]
[<0000000061d90a04>] tasklet_action_common.constprop.0+0xdc/0x128
[<000000006292f300>] __do_softirq+0x130/0x3c0
[<0000000061d906c6>] irq_exit_rcu+0xfe/0x118
[<000000006291e818>] do_io_irq+0xc8/0x168
[<000000006292d516>] io_int_handler+0xd6/0x110
[<000000006292d596>] psw_idle_exit+0x0/0xa
([<0000000061d3be50>] arch_cpu_idle+0x40/0xd0)
[<000000006292ceea>] default_idle_call+0x52/0xf8
[<0000000061de4fa4>] do_idle+0xd4/0x168
[<0000000061de51fe>] cpu_startup_entry+0x36/0x40
[<0000000061d4faac>] smp_start_secondary+0x12c/0x138
[<000000006292d88e>] restart_int_handler+0x6e/0x90
Last Breaking-Event-Address:
[<000003ff7febaf94>] zfcp_fsf_reqid_check+0x8c/0x158 [zfcp]
Kernel panic - not syncing: Fatal exception in interrupt
or:
Unable to handle kernel pointer dereference in virtual kernel address space
Failing address: 523b05d3ae76a000 TEID: 523b05d3ae76a803
Fault in home space mode while using kernel ASCE.
AS:0000000077c40007 R3:0000000000000024
Oops: 0038 ilc:3 [#1] SMP
Modules linked in: ...
CPU: 3 PID: 453 Comm: kworker/3:1H Kdump: loaded
Hardware name: ...
Workqueue: kblockd blk_mq_run_work_fn
Krnl PSW : 0404d00180000000 0000000076fc0312 (__kmalloc+0xd2/0x398)
R:0 T:1 IO:0 EX:0 Key:0 M:1 W:0 P:0 AS:3 CC:1 PM:0 RI:0 EA:3
Krnl GPRS: ffffffffffffffff 523b05d3ae76abf6 0000000000000000 0000000000092a20
0000000000000002 00000007e49b5cc0 00000007eda8f000 0000000000092a20
00000007eda8f000 00000003b02856b9 00000000000000a8 523b05d3ae76abf6
00000007dd662000 00000007eda8f000 0000000076fc02b2 000003e0037637a0
Krnl Code: 0000000076fc0302: c004000000d4 brcl 0,76fc04aa
0000000076fc0308: b904001b lgr %r1,%r11
#0000000076fc030c: e3106020001a algf %r1,32(%r6)
>0000000076fc0312: e31010000082 xg %r1,0(%r1)
0000000076fc0318: b9040001 lgr %r0,%r1
0000000076fc031c: e30061700082 xg %r0,368(%r6)
0000000076fc0322: ec59000100d9 aghik %r5,%r9,1
0000000076fc0328: e34003b80004 lg %r4,952
Call Trace:
[<0000000076fc0312>] __kmalloc+0xd2/0x398
[<0000000076f318f2>] mempool_alloc+0x72/0x1f8
[<000003ff8027c5f8>] zfcp_fsf_req_create.isra.7+0x40/0x268 [zfcp]
[<000003ff8027f1bc>] zfcp_fsf_fcp_cmnd+0xac/0x3f0 [zfcp]
[<000003ff80280f1a>] zfcp_scsi_queuecommand+0x122/0x1d0 [zfcp]
[<000003ff800b4218>] scsi_queue_rq+0x778/0xa10 [scsi_mod]
[<00000000771782a0>] __blk_mq_try_issue_directly+0x130/0x208
[<000000007717a124>] blk_mq_request_issue_directly+0x4c/0xa8
[<000003ff801302e2>] dm_mq_queue_rq+0x2ea/0x468 [dm_mod]
[<0000000077178c12>] blk_mq_dispatch_rq_list+0x33a/0x818
[<000000007717f064>] __blk_mq_do_dispatch_sched+0x284/0x2f0
[<000000007717f44c>] __blk_mq_sched_dispatch_requests+0x1c4/0x218
[<000000007717fa7a>] blk_mq_sched_dispatch_requests+0x52/0x90
[<0000000077176d74>] __blk_mq_run_hw_queue+0x9c/0xc0
[<0000000076da6d74>] process_one_work+0x274/0x4d0
[<0000000076da7018>] worker_thread+0x48/0x560
[<0000000076daef18>] kthread+0x140/0x160
[<000000007751d144>] ret_from_fork+0x28/0x30
Last Breaking-Event-Address:
[<0000000076fc0474>] __kmalloc+0x234/0x398
Kernel panic - not syncing: Fatal exception: panic_on_oops
To fix this, simply change the type of the cache variable to 'unsigned
long', like the rest of zfcp and also the argument for
'zfcp_reqlist_find_rm()'. This prevents truncation and wrong sign extension
and so can successfully remove the request from the hash table.
Fixes: e60a6d69f1 ("[SCSI] zfcp: Remove function zfcp_reqlist_find_safe")
Cc: <stable@vger.kernel.org> #v2.6.34+
Signed-off-by: Benjamin Block <bblock@linux.ibm.com>
Link: https://lore.kernel.org/r/979f6e6019d15f91ba56182f1aaf68d61bf37fc6.1668595505.git.bblock@linux.ibm.com
Reviewed-by: Steffen Maier <maier@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4fe1ec9954 upstream.
__list_versions will first estimate the required space using the
"dm_target_iterate(list_version_get_needed, &needed)" call and then will
fill the space using the "dm_target_iterate(list_version_get_info,
&iter_info)" call. Each of these calls locks the targets using the
"down_read(&_lock)" and "up_read(&_lock)" calls, however between the first
and second "dm_target_iterate" there is no lock held and the target
modules can be loaded at this point, so the second "dm_target_iterate"
call may need more space than what was the first "dm_target_iterate"
returned.
The code tries to handle this overflow (see the beginning of
list_version_get_info), however this handling is incorrect.
The code sets "param->data_size = param->data_start + needed" and
"iter_info.end = (char *)vers+len" - "needed" is the size returned by the
first dm_target_iterate call; "len" is the size of the buffer allocated by
userspace.
"len" may be greater than "needed"; in this case, the code will write up
to "len" bytes into the buffer, however param->data_size is set to
"needed", so it may write data past the param->data_size value. The ioctl
interface copies only up to param->data_size into userspace, thus part of
the result will be truncated.
Fix this bug by setting "iter_info.end = (char *)vers + needed;" - this
guarantees that the second "dm_target_iterate" call will write only up to
the "needed" buffer and it will exit with "DM_BUFFER_FULL_FLAG" if it
overflows the "needed" space - in this case, userspace will allocate a
larger buffer and retry.
Note that there is also a bug in list_version_get_needed - we need to add
"strlen(tt->name) + 1" to the needed size, not "strlen(tt->name)".
Cc: stable@vger.kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit efa17e90e1 upstream.
dev_set_name() allocates memory for name, it need be freed
when device_add() fails, call put_device() to give up the
reference that hold in device_initialize(), so that it can
be freed in kobject_cleanup() when the refcount hit to 0.
Fault injection test can trigger this:
unreferenced object 0xffff8e8340a7b4c0 (size 32):
comm "modprobe", pid 243, jiffies 4294678145 (age 48.845s)
hex dump (first 32 bytes):
69 69 6f 5f 73 79 73 66 73 5f 74 72 69 67 67 65 iio_sysfs_trigge
72 00 a7 40 83 8e ff ff 00 86 13 c4 f6 ee ff ff r..@............
backtrace:
[<0000000074999de8>] __kmem_cache_alloc_node+0x1e9/0x360
[<00000000497fd30b>] __kmalloc_node_track_caller+0x44/0x1a0
[<000000003636c520>] kstrdup+0x2d/0x60
[<0000000032f84da2>] kobject_set_name_vargs+0x1e/0x90
[<0000000092efe493>] dev_set_name+0x4e/0x70
Fixes: 1f785681a8 ("staging:iio:trigger sysfs userspace trigger rework.")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20221022074212.1386424-1-yangyingliang@huawei.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40bf8f162d upstream.
There is no point to enter safe mode during DP/TBT configuration
if the DP/TBT was already configured in mux. This is because safe
mode is only applicable when there is a need to reconfigure the
pins in order to avoid damage within/to port partner.
In some chrome systems, IOM/mux is already configured before OS
comes up. Thus, when driver is probed, it blindly enters safe
mode due to PD negotiations but only after gfx driver lowers
dp_phy_ownership, will the IOM complete safe mode and send an
ack to PMC.
Since, that never happens, we see IPC timeout.
Hence, allow safe mode only when pin reconfiguration is not
required, which makes sense.
Fixes: 43d596e322 ("usb: typec: intel_pmc_mux: Check the port status before connect")
Cc: stable <stable@kernel.org>
Signed-off-by: Rajat Khandelwal <rajat.khandelwal@linux.intel.com>
Signed-off-by: Lee Shawn C <shawn.c.lee@intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20221024171611.181468-1-rajat.khandelwal@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9d5333c931 upstream.
When usb 3.0 hub connect with one USB 2.0 device and NO USB 3.0 device,
some usb hub reports endless port reset message.
[ 190.324169] usb 2-1: new SuperSpeed USB device number 88 using xhci-hcd
[ 190.352834] hub 2-1:1.0: USB hub found
[ 190.356995] hub 2-1:1.0: 4 ports detected
[ 190.700056] usb 2-1: USB disconnect, device number 88
[ 192.472139] usb 2-1: new SuperSpeed USB device number 89 using xhci-hcd
[ 192.500820] hub 2-1:1.0: USB hub found
[ 192.504977] hub 2-1:1.0: 4 ports detected
[ 192.852066] usb 2-1: USB disconnect, device number 89
The reason is the runtime pm state of USB2.0 port is active and
USB 3.0 port is suspend, so parent device is active state.
cat /sys/bus/platform/devices/5b110000.usb/5b130000.usb/xhci-hcd.1.auto/usb2/power/runtime_status
suspended
cat /sys/bus/platform/devices/5b110000.usb/5b130000.usb/xhci-hcd.1.auto/usb1/power/runtime_status
active
cat /sys/bus/platform/devices/5b110000.usb/5b130000.usb/xhci-hcd.1.auto/power/runtime_status
active
cat /sys/bus/platform/devices/5b110000.usb/5b130000.usb/power/runtime_status
active
So xhci_cdns3_suspend_quirk() have not called. U3 configure is not applied.
move U3 configure into host start. Reinit again in resume function in case
controller power lost during suspend.
Cc: stable@vger.kernel.org 5.10
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20221026190749.2280367-1-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a58b8d602 upstream.
There is a deadlock in ci_otg_del_timer(), the process is
shown below:
(thread 1) | (thread 2)
ci_otg_del_timer() | ci_otg_hrtimer_func()
... |
spin_lock_irqsave() //(1) | ...
... |
hrtimer_cancel() | spin_lock_irqsave() //(2)
(block forever)
We hold ci->lock in position (1) and use hrtimer_cancel() to
wait ci_otg_hrtimer_func() to stop, but ci_otg_hrtimer_func()
also need ci->lock in position (2). As a result, the
hrtimer_cancel() in ci_otg_del_timer() will be blocked forever.
This patch extracts hrtimer_cancel() from the protection of
spin_lock_irqsave() in order that the ci_otg_hrtimer_func()
could obtain the ci->lock.
What`s more, there will be no race happen. Because the
"next_timer" is always under the protection of
spin_lock_irqsave() and we only check whether "next_timer"
equals to NUM_OTG_FSM_TIMERS in the following code.
Fixes: 3a316ec4c9 ("usb: chipidea: use hrtimer for otg fsm timers")
Cc: stable <stable@kernel.org>
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/20220918033312.94348-1-duoming@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1547f12df upstream.
Add LARA-L6 PIDs for three different USB compositions.
LARA-L6 module can be configured (by AT interface) in three different
USB modes:
* Default mode (Vendor ID: 0x1546 Product ID: 0x1341) with 4 serial
interfaces
* RmNet mode (Vendor ID: 0x1546 Product ID: 0x1342) with 4 serial
interfaces and 1 RmNet virtual network interface
* CDC-ECM mode (Vendor ID: 0x1546 Product ID: 0x1343) with 4 serial
interface and 1 CDC-ECM virtual network interface
In default mode LARA-L6 exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parser/alternative functions
In RmNet mode LARA-L6 exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parset/alternative functions
If 4: RMNET interface
In CDC-ECM mode LARA-L6 exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parset/alternative functions
If 4: CDC-ECM interface
Signed-off-by: Davide Tronchin <davide.tronchin.94@gmail.com>
[ johan: drop PID defines in favour of comments ]
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d9e37a5c4d upstream.
The official LARA-R6 (00B) modem uses 0x908b PID. LARA-R6 00B does not
implement a QMI interface on port 4, the reservation (RSVD(4)) has been
added to meet other companies that implement QMI on that interface.
LARA-R6 00B USB composition exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parser/alternative functions
Signed-off-by: Davide Tronchin <davide.tronchin.94@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd136706b4 upstream.
What the code does is to not check the return value from
devm_gpiod_get() and then avoid using an erroneous GPIO descriptor
with IS_ERR_OR_NULL().
This will miss real errors from the GPIO core that should not be
ignored, such as probe deferral.
Instead request the GPIO as explicitly optional, which means that
if it doesn't exist, the descriptor returned will be NULL.
Then we can add error handling and also avoid just doing this on
the device tree path, and simplify the site where the optional
GPIO descriptor is used.
There were some problems with cleaning up this GPIO descriptor
use in the past, but this is the proper way to deal with it.
Cc: Rafał Miłecki <rafal@milecki.pl>
Cc: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20221107090753.1404679-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0fc801f801 upstream.
This patch fixes a segfault by adding a null check on synth in
speakup_con_update(). The segfault can be reproduced as follows:
- Login into a text console
- Load speakup and speakup_soft modules
- Remove speakup_soft
- Switch to a graphics console
This is caused by lack of a null check on `synth` in
speakup_con_update().
Here's the sequence that causes the segfault:
- When we remove the speakup_soft, synth_release() sets the synth
to null.
- After that, when we change the virtual console to graphics
console, vt_notifier_call() is fired, which then calls
speakup_con_update().
- Inside speakup_con_update() there's no null check on synth,
so it calls synth_printf().
- Inside synth_printf(), synth_buffer_add() and synth_start(),
both access synth, when it is null and causing a segfault.
Therefore adding a null check on synth solves the issue.
Fixes: 2610df4148 ("staging: speakup: Add pause command used on switching to graphical mode")
Cc: stable <stable@kernel.org>
Signed-off-by: Mushahid Hussain <mushi.shar@gmail.com>
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Link: https://lore.kernel.org/r/20221010165720.397042-1-mushi.shar@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e54fad8044 upstream.
If CONFIG_SLIM_QCOM_NGD_CTRL=y, CONFIG_QCOM_RPROC_COMMON=m, COMPILE_TEST=y,
bulding fails:
drivers/slimbus/qcom-ngd-ctrl.o: In function `qcom_slim_ngd_ctrl_probe':
qcom-ngd-ctrl.c:(.text+0x330): undefined reference to `qcom_register_ssr_notifier'
qcom-ngd-ctrl.c:(.text+0x5fc): undefined reference to `qcom_unregister_ssr_notifier'
drivers/slimbus/qcom-ngd-ctrl.o: In function `qcom_slim_ngd_remove':
qcom-ngd-ctrl.c:(.text+0x90c): undefined reference to `qcom_unregister_ssr_notifier'
Make SLIM_QCOM_NGD_CTRL depends on QCOM_RPROC_COMMON || (COMPILE_TEST && !QCOM_RPROC_COMMON) to fix this.
Fixes: e291691c69 ("slimbus: qcom-ngd-ctrl: allow compile testing without QCOM_RPROC_COMMON")
Cc: stable <stable@kernel.org>
Signed-off-by: Zheng Bin <zhengbin13@huawei.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221027095904.3388959-1-zhengbin13@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c294de36e upstream.
This reverts commit 6000b8d900.
The offending commit disabled the USB core PHY management as the dwc3
already manages the PHYs in question.
Unfortunately some platforms have started relying on having USB core
also controlling the PHY and this is specifically currently needed on
some Exynos platforms for PHY calibration or connected device may fail
to enumerate.
The PHY calibration was previously handled in the dwc3 driver, but to
work around some issues related to how the dwc3 driver interacts with
xhci (e.g. using multiple drivers) this was moved to USB core by commits
34c7ed72f4 ("usb: core: phy: add support for PHY calibration") and
a0a465569b ("usb: dwc3: remove generic PHY calibrate() calls").
The same PHY obviously should not be controlled from two different
places, which for example do no agree on the PHY mode or power state
during suspend, but as the offending patch was backported to stable,
let's revert it for now.
Reported-by: Stefan Agner <stefan@agner.ch>
Link: https://lore.kernel.org/lkml/808bdba846bb60456adf10a3016911ee@agner.ch/
Fixes: 6000b8d900 ("usb: dwc3: disable USB core PHY management")
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20221103144648.14197-1-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7af87fc1ba upstream.
On IGT, there is a test named amd_hotplug, and when the subtest basic is
executed on DCN31, we get the following error:
[drm] *ERROR* [CRTC:71:crtc-0] flip_done timed out
[drm] *ERROR* flip_done timed out
[drm] *ERROR* [CRTC:71:crtc-0] commit wait timed out
[drm] *ERROR* flip_done timed out
[drm] *ERROR* [CONNECTOR:88:DP-1] commit wait timed out
[drm] *ERROR* flip_done timed out
[drm] *ERROR* [PLANE:59:plane-3] commit wait timed out
After enable the page flip log with the below command:
echo -n 'format "[PFLIP]" +p' > /sys/kernel/debug/dynamic_debug/control
It is possible to see that the flip was submitted, but DC never replied
back, which generates time-out issues. This is an indication that the
HUBP surface flip is missing. This commit fixes this issue by adding
hubp1_set_flip_int to DCN31.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 42fb0a1e84 upstream.
Currently the way polling works on the ring buffer is broken. It will
return immediately if there's any data in the ring buffer whereas a read
will block until the watermark (defined by the tracefs buffer_percent file)
is hit.
That is, a select() or poll() will return as if there's data available,
but then the following read will block. This is broken for the way
select()s and poll()s are supposed to work.
Have the polling on the ring buffer also block the same way reads and
splice does on the ring buffer.
Link: https://lkml.kernel.org/r/20221020231427.41be3f26@gandalf.local.home
Cc: Linux Trace Kernel <linux-trace-kernel@vger.kernel.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Primiano Tucci <primiano@google.com>
Cc: stable@vger.kernel.org
Fixes: 1e0d6714ac ("ring-buffer: Do not wake up a splice waiter when page is not full")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 19ba6c8af9 upstream.
The @ftrace_mod is allocated by kzalloc(), so both the members {prev,next}
of @ftrace_mode->list are NULL, it's not a valid state to call list_del().
If kstrdup() for @ftrace_mod->{func|module} fails, it goes to @out_free
tag and calls free_ftrace_mod() to destroy @ftrace_mod, then list_del()
will write prev->next and next->prev, where null pointer dereference
happens.
BUG: kernel NULL pointer dereference, address: 0000000000000008
Oops: 0002 [#1] PREEMPT SMP NOPTI
Call Trace:
<TASK>
ftrace_mod_callback+0x20d/0x220
? do_filp_open+0xd9/0x140
ftrace_process_regex.isra.51+0xbf/0x130
ftrace_regex_write.isra.52.part.53+0x6e/0x90
vfs_write+0xee/0x3a0
? __audit_filter_op+0xb1/0x100
? auditd_test_task+0x38/0x50
ksys_write+0xa5/0xe0
do_syscall_64+0x3a/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Kernel panic - not syncing: Fatal exception
So call INIT_LIST_HEAD() to initialize the list member to fix this issue.
Link: https://lkml.kernel.org/r/20221116015207.30858-1-xiujianfeng@huawei.com
Cc: stable@vger.kernel.org
Fixes: 673feb9d76 ("ftrace: Add :mod: caching infrastructure to trace_array")
Signed-off-by: Xiu Jianfeng <xiujianfeng@huawei.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a51e5d293d ]
If the returning value of SMB2_set_info_init is an error-value,
exit the function.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 0967e54579 ("cifs: use a compound for setting an xattr")
Signed-off-by: Anastasia Belova <abelova@astralinux.ru>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f524b7289b ]
A problem about insmod thunderbolt-net failed is triggered with following
log given while lsmod does not show thunderbolt_net:
insmod: ERROR: could not insert module thunderbolt-net.ko: File exists
The reason is that tbnet_init() returns tb_register_service_driver()
directly without checking its return value, if tb_register_service_driver()
failed, it returns without removing property directory, resulting the
property directory can never be created later.
tbnet_init()
tb_register_property_dir() # register property directory
tb_register_service_driver()
driver_register()
bus_add_driver()
priv = kzalloc(...) # OOM happened
# return without remove property directory
Fix by remove property directory when tb_register_service_driver() returns
error.
Fixes: e69b6c02b4 ("net: Add support for networking over Thunderbolt cable")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 639f5d006e ]
sparx_stats_init() calls create_singlethread_workqueue() and not
checked the ret value, which may return NULL. And a null-ptr-deref may
happen:
sparx_stats_init()
create_singlethread_workqueue() # failed, sparx5->stats_queue is NULL
queue_delayed_work()
queue_delayed_work_on()
__queue_delayed_work() # warning here, but continue
__queue_work() # access wq->flags, null-ptr-deref
Check the ret value and return -ENOMEM if it is NULL. So as
sparx5_start().
Fixes: af4b11022e ("net: sparx5: add ethtool configuration and statistics support")
Fixes: b37a1bae74 ("net: sparx5: add mactable support")
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92bbd67a55 ]
The return value of CIFSGetExtAttr is negative, should be checked
with -EOPNOTSUPP rather than EOPNOTSUPP.
Fixes: 64a5cfa6db ("Allow setting per-file compression via SMB2/3")
Signed-off-by: Zhang Xiaoxu <zhangxiaoxu5@huawei.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d520de6cb4 ]
If the returning value of SMB2_close_init is an error-value,
exit the function.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 352d96f3ac ("cifs: multichannel: move channel selection above transport layer")
Signed-off-by: Anastasia Belova <abelova@astralinux.ru>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d9a477f643 ]
Currently, we check any received packet whether we have already seen it
previously, regardless of the packet type (sequenced / unsequenced). We
do this by checking the sequence number. This assumes that sequence
numbers are valid for both sequenced and unsequenced packets. However,
this assumption appears to be incorrect.
On some devices, the sequence number field of unsequenced packets (in
particular HID input events on the Surface Pro 9) is always zero. As a
result, the current retransmission check kicks in and discards all but
the first unsequenced packet, breaking (among other things) keyboard and
touchpad input.
Note that we have, so far, only seen packets being retransmitted in
sequenced communication. In particular, this happens when there is an
ACK timeout, causing the EC (or us) to re-send the packet waiting for an
ACK. Arguably, retransmission / duplication of unsequenced packets
should not be an issue as there is no logical condition (such as an ACK
timeout) to determine when a packet should be sent again.
Therefore, remove the retransmission check for unsequenced packets
entirely to resolve the issue.
Fixes: c167b9c7e3 ("platform/surface: Add Surface Aggregator subsystem")
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/20221113185951.224759-1-luzmaximilian@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2dbfb3f333 ]
The current logic in the Intel PMC driver will forcefully attach it
when detecting any CPU on the intel_pmc_core_platform_ids array,
even if the matching ACPI device is not present.
There's no checking in pmc_core_probe() to assert that the PMC device
is present, and hence on virtualized environments the PMC device
probes successfully, even if the underlying registers are not present.
Before commit 21ae435709 ("platform/x86: intel_pmc_core: Substitute PCI
with CPUID enumeration") the driver would check for the presence of a
specific PCI device, and that prevented the driver from attaching when
running virtualized.
Fix by only forcefully attaching the PMC device when not running
virtualized. Note that virtualized platforms can still get the device
to load if the appropriate ACPI device is present on the tables
provided to the VM.
Make an exception for the Xen initial domain, which does have full
hardware access, and hence can attach to the PMC if present.
Fixes: 21ae435709 ("platform/x86: intel_pmc_core: Substitute PCI with CPUID enumeration")
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Acked-by: David E. Box <david.e.box@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221110163145.80374-1-roger.pau@citrix.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d45921ee4 ]
The bridge driver can offload VLANs to the underlying hardware either
via switchdev or the 8021q driver. When the former is used, the VLAN is
marked in the bridge driver with the 'BR_VLFLAG_ADDED_BY_SWITCHDEV'
private flag.
To avoid the memory leaks mentioned in the cited commit, the bridge
driver will try to delete a VLAN via the 8021q driver if the VLAN is not
marked with the previously mentioned flag.
When the VLAN protocol of the bridge changes, switchdev drivers are
notified via the 'SWITCHDEV_ATTR_ID_BRIDGE_VLAN_PROTOCOL' attribute, but
the 8021q driver is also called to add the existing VLANs with the new
protocol and delete them with the old protocol.
In case the VLANs were offloaded via switchdev, the above behavior is
both redundant and buggy. Redundant because the VLANs are already
programmed in hardware and drivers that support VLAN protocol change
(currently only mlx5) change the protocol upon the switchdev attribute
notification. Buggy because the 8021q driver is called despite these
VLANs being marked with 'BR_VLFLAG_ADDED_BY_SWITCHDEV'. This leads to
memory leaks [1] when the VLANs are deleted.
Fix by not calling the 8021q driver for VLANs that were already
programmed via switchdev.
[1]
unreferenced object 0xffff8881f6771200 (size 256):
comm "ip", pid 446855, jiffies 4298238841 (age 55.240s)
hex dump (first 32 bytes):
00 00 7f 0e 83 88 ff ff 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<00000000012819ac>] vlan_vid_add+0x437/0x750
[<00000000f2281fad>] __br_vlan_set_proto+0x289/0x920
[<000000000632b56f>] br_changelink+0x3d6/0x13f0
[<0000000089d25f04>] __rtnl_newlink+0x8ae/0x14c0
[<00000000f6276baf>] rtnl_newlink+0x5f/0x90
[<00000000746dc902>] rtnetlink_rcv_msg+0x336/0xa00
[<000000001c2241c0>] netlink_rcv_skb+0x11d/0x340
[<0000000010588814>] netlink_unicast+0x438/0x710
[<00000000e1a4cd5c>] netlink_sendmsg+0x788/0xc40
[<00000000e8992d4e>] sock_sendmsg+0xb0/0xe0
[<00000000621b8f91>] ____sys_sendmsg+0x4ff/0x6d0
[<000000000ea26996>] ___sys_sendmsg+0x12e/0x1b0
[<00000000684f7e25>] __sys_sendmsg+0xab/0x130
[<000000004538b104>] do_syscall_64+0x3d/0x90
[<0000000091ed9678>] entry_SYSCALL_64_after_hwframe+0x46/0xb0
Fixes: 279737939a ("net: bridge: Fix VLANs memory leak")
Reported-by: Vlad Buslov <vladbu@nvidia.com>
Tested-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20221114084509.860831-1-idosch@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 510d7b6ae8 ]
Currently, if driver is in phy-imp(phy controlled by imp firmware) mode, as
driver did not update phy link ksettings after initialization process or
not update advertising when getting phy link ksettings from firmware, it
may set incorrect phy link ksettings for firmware in resetting process.
So fix it.
Fixes: f5f2b3e4dc ("net: hns3: add support for imp-controlled PHYs")
Fixes: c5ef83cbb1 ("net: hns3: fix for phy_addr error in hclge_mac_mdio_config")
Fixes: 2312e050f4 ("net: hns3: Fix for deadlock problem occurring when unregistering ae_algo")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 280c0f7cd0 ]
A problem about ionic create debugfs failed is triggered with the
following log given:
[ 415.799514] debugfs: Directory 'ionic' with parent '/' already present!
The reason is that ionic_init_module() returns ionic_bus_register_driver()
directly without checking its return value, if ionic_bus_register_driver()
failed, it returns without destroy the newly created debugfs, resulting
the debugfs of ionic can never be created later.
ionic_init_module()
ionic_debugfs_create() # create debugfs directory
ionic_bus_register_driver()
pci_register_driver()
driver_register()
bus_add_driver()
priv = kzalloc(...) # OOM happened
# return without destroy debugfs directory
Fix by removing debugfs when ionic_bus_register_driver() returns error.
Fixes: fbfb803153 ("ionic: Add hardware init and device commands")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Link: https://lore.kernel.org/r/20221113092929.19161-1-yuancan@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da36a2a76b ]
In device_add(), dev_set_name() is called to allocate name, if it returns
error, the name need be freed. As comment of device_register() says, it
should use put_device() to give up the reference in the error path. So fix
this by calling put_device(), then the name can be freed in kobject_cleanup().
Fixes: f65c9bb3fb ("xen/pcpu: Xen physical cpus online/offline sys interface")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20221110152441.401630-1-yangyingliang@huawei.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed1fe1bebe ]
There are multi-generational drivers like mv88e6xxx which have code like
this:
int mv88e6xxx_port_hwtstamp_get(struct dsa_switch *ds, int port,
struct ifreq *ifr)
{
if (!chip->info->ptp_support)
return -EOPNOTSUPP;
...
}
DSA wants to deny PTP timestamping on the master if the switch supports
timestamping too. However it currently relies on the presence of the
port_hwtstamp_get() callback to determine PTP capability, and this
clearly does not work in that case (method is present but returns
-EOPNOTSUPP).
We should not deny PTP on the DSA master for those switches which truly
do not support hardware timestamping.
Create a dsa_port_supports_hwtstamp() method which actually probes for
support by calling port_hwtstamp_get() and seeing whether that returned
-EOPNOTSUPP or not.
Fixes: f685e609a3 ("net: dsa: Deny PTP on master if switch supports it")
Link: https://patchwork.kernel.org/project/netdevbpf/patch/20221110124345.3901389-1-festevam@gmail.com/
Reported-by: Fabio Estevam <festevam@gmail.com>
Reported-by: Steffen Bätz <steffen@innosonix.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f7c125bd79 ]
MHI driver registers network device without setting the
needs_free_netdev flag, and does NOT call free_netdev() when
unregisters network device, which causes a memory leak.
This patch calls free_netdev() to fix it since netdev_priv
is used after unregister.
Fixes: 13adac0329 ("net: mhi_net: Register wwan_ops for link creation")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 991aef4ee4 ]
When pci_register_driver failed, we need to remove debugfs,
which will caused a resource leak, fix it.
Resource leak logs as follows:
[ 52.184456] debugfs: Directory 'bnxt_en' with parent '/' already present!
Fixes: cabfb09d87 ("bnxt_en: add debugfs support for DIM")
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8fbb53c8bf ]
When connecting to client timeout, disconnect client for twice in
chnl_net_open(). Remove one. Compile tested only.
Fixes: 2aa40aef9d ("caif: Use link layer MTU instead of fixed MTU")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5df1341ea8 ]
hlist_for_each_entry_rcu() has built-in RCU and lock checking.
Pass cond argument to hlist_for_each_entry_rcu() to silence false
lockdep warning when CONFIG_PROVE_RCU_LIST is enabled.
Execute as follow:
ip link add link eth0 type macvlan mode source macaddr add <MAC-ADDR>
The rtnl_lock is held when macvlan_hash_lookup_source() or
macvlan_fill_info_macaddr() are called in the non-RCU read side section.
So, pass lockdep_rtnl_is_held() to silence false lockdep warning.
Fixes: 79cf79abce ("macvlan: add source mode")
Signed-off-by: Chuang Wang <nashuiliang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d25107e11 ]
We should not release reference by put_device() before calling device_initialize().
Fixes: e7d1d4d9ac ("mISDN: fix possible memory leak in mISDN_register_device()")
Signed-off-by: Wang ShaoBo <bobo.shaobowang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 836fb30949 ]
Commit 7d981405d0 ("soc: imx8m: change to use platform driver") ever
removed the dependency on bootloader for enabling OCOTP clock. It
helped to fix a kexec kernel hang issue. But unfortunately it caused
a regression on CAAM driver and got reverted.
This is the second try to enable the OCOTP clock by directly calling
clock API instead of indirectly enabling the clock via nvmem API.
Fixes: ac34de14ac ("Revert "soc: imx8m: change to use platform driver"")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8eab9be56c ]
A problem about hinic create debugfs failed is triggered with the
following log given:
[ 931.419023] debugfs: Directory 'hinic' with parent '/' already present!
The reason is that hinic_module_init() returns pci_register_driver()
directly without checking its return value, if pci_register_driver()
failed, it returns without destroy the newly created debugfs, resulting
the debugfs of hinic can never be created later.
hinic_module_init()
hinic_dbg_register_debugfs() # create debugfs directory
pci_register_driver()
driver_register()
bus_add_driver()
priv = kzalloc(...) # OOM happened
# return without destroy debugfs directory
Fix by removing debugfs when pci_register_driver() returns error.
Fixes: 253ac3a979 ("hinic: add support to query sq info")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20221110021642.80378-1-yuancan@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 98a2ac1ca8 ]
Afer commit 1fa5ae857b ("driver core: get rid of struct device's
bus_id string array"), the name of device is allocated dynamically,
use put_device() to give up the reference, so that the name can be
freed in kobject_cleanup() when the refcount is 0.
The 'entry' is going to be freed in mISDN_dsp_dev_release(), so the
kfree() is removed. list_del() is called in mISDN_dsp_dev_release(),
so it need be initialized.
Fixes: 1fa5ae857b ("driver core: get rid of struct device's bus_id string array")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221109132832.3270119-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b45cd81f7 ]
pcpu_freelist_populate() initializes nr_elems / num_possible_cpus() + 1
free nodes for some CPUs, and then possibly one CPU with fewer nodes,
followed by remaining cpus with 0 nodes. For example, when nr_elems == 256
and num_possible_cpus() == 32, CPU 0~27 each gets 9 free nodes, CPU 28 gets
4 free nodes, CPU 29~31 get 0 free nodes, while in fact each CPU should get
8 nodes equally.
This patch initializes nr_elems / num_possible_cpus() free nodes for each
CPU firstly, then allocates the remaining free nodes by one for each CPU
until no free nodes left.
Fixes: e19494edab ("bpf: introduce percpu_freelist")
Signed-off-by: Xu Kuohai <xukuohai@huawei.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20221110122128.105214-1-xukuohai@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 612d80784f ]
Building with clang-14 fails with:
AS arch/mips/kernel/relocate_kernel.o
<unknown>:0: error: symbol 'kexec_args' is already defined
<unknown>:0: error: symbol 'secondary_kexec_args' is already defined
<unknown>:0: error: symbol 'kexec_start_address' is already defined
<unknown>:0: error: symbol 'kexec_indirection_page' is already defined
<unknown>:0: error: symbol 'relocate_new_kernel_size' is already defined
It turns out EXPORT defined in asm/asm.h expands to a symbol definition,
so there is no need to define these symbols again. Remove duplicated
symbol definitions.
Fixes: 7aa1c8f47e ("MIPS: kdump: Add support")
Signed-off-by: Rongwei Zhang <pudh4418@gmail.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3a72878a3 ]
Extend the size of QSFP EEPROM for types SSF8436 and SFF8636
from 256 to 640 bytes in order to expose all the EEPROM pages by
ethtool.
For SFF-8636 and SFF-8436 specifications, the driver exposes
256 bytes of EEPROM data for ethtool's get_module_eeprom()
callback, resulting in "netlink error: Invalid argument" when
an EEPROM read with an offset larger than 256 bytes is attempted.
Changing the length enumerators to the _MAX_LEN
variants exposes all 640 bytes of the EEPROM allowing upper
pages 1, 2 and 3 to be read.
Fixes: 96d971e307 ("ethtool: Add fallback to get_module_eeprom from netlink command")
Signed-off-by: Jaco Coetzee <jaco.coetzee@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ff3635130 ]
In ata_tdev_add(), the return value of transport_add_device() is
not checked. As a result, it causes null-ptr-deref while removing
the module, because transport_remove_device() is called to remove
the device that was not added.
Unable to handle kernel NULL pointer dereference at virtual address 00000000000000d0
CPU: 13 PID: 13603 Comm: rmmod Kdump: loaded Tainted: G W 6.1.0-rc3+ #36
pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : device_del+0x48/0x3a0
lr : device_del+0x44/0x3a0
Call trace:
device_del+0x48/0x3a0
attribute_container_class_device_del+0x28/0x40
transport_remove_classdev+0x60/0x7c
attribute_container_device_trigger+0x118/0x120
transport_remove_device+0x20/0x30
ata_tdev_delete+0x24/0x50 [libata]
ata_tlink_delete+0x40/0xa0 [libata]
ata_tport_delete+0x2c/0x60 [libata]
ata_port_detach+0x148/0x1b0 [libata]
ata_pci_remove_one+0x50/0x80 [libata]
ahci_remove_one+0x4c/0x8c [ahci]
Fix this by checking and handling return value of transport_add_device()
in ata_tdev_add(). In the error path, device_del() is called to delete
the device which was added earlier in this function, and ata_tdev_free()
is called to free ata_dev.
Fixes: d9027470b8 ("[libata] Add ATA transport class")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf0816f632 ]
In ata_tlink_add(), the return value of transport_add_device() is
not checked. As a result, it causes null-ptr-deref while removing
the module, because transport_remove_device() is called to remove
the device that was not added.
Unable to handle kernel NULL pointer dereference at virtual address 00000000000000d0
CPU: 33 PID: 13850 Comm: rmmod Kdump: loaded Tainted: G W 6.1.0-rc3+ #12
pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : device_del+0x48/0x39c
lr : device_del+0x44/0x39c
Call trace:
device_del+0x48/0x39c
attribute_container_class_device_del+0x28/0x40
transport_remove_classdev+0x60/0x7c
attribute_container_device_trigger+0x118/0x120
transport_remove_device+0x20/0x30
ata_tlink_delete+0x88/0xb0 [libata]
ata_tport_delete+0x2c/0x60 [libata]
ata_port_detach+0x148/0x1b0 [libata]
ata_pci_remove_one+0x50/0x80 [libata]
ahci_remove_one+0x4c/0x8c [ahci]
Fix this by checking and handling return value of transport_add_device()
in ata_tlink_add().
Fixes: d9027470b8 ("[libata] Add ATA transport class")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3613dbe390 ]
In ata_tport_add(), the return value of transport_add_device() is
not checked. As a result, it causes null-ptr-deref while removing
the module, because transport_remove_device() is called to remove
the device that was not added.
Unable to handle kernel NULL pointer dereference at virtual address 00000000000000d0
CPU: 12 PID: 13605 Comm: rmmod Kdump: loaded Tainted: G W 6.1.0-rc3+ #8
pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : device_del+0x48/0x39c
lr : device_del+0x44/0x39c
Call trace:
device_del+0x48/0x39c
attribute_container_class_device_del+0x28/0x40
transport_remove_classdev+0x60/0x7c
attribute_container_device_trigger+0x118/0x120
transport_remove_device+0x20/0x30
ata_tport_delete+0x34/0x60 [libata]
ata_port_detach+0x148/0x1b0 [libata]
ata_pci_remove_one+0x50/0x80 [libata]
ahci_remove_one+0x4c/0x8c [ahci]
Fix this by checking and handling return value of transport_add_device()
in ata_tport_add().
Fixes: d9027470b8 ("[libata] Add ATA transport class")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c76310740 ]
In the error path in ata_tport_add(), when calling put_device(),
ata_tport_release() is called, it will put the refcount of 'ap->host'.
And then ata_host_put() is called again, the refcount is decreased
to 0, ata_host_release() is called, all ports are freed and set to
null.
When unbinding the device after failure, ata_host_stop() is called
to release the resources, it leads a null-ptr-deref(), because all
the ports all freed and null.
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000008
CPU: 7 PID: 18671 Comm: modprobe Kdump: loaded Tainted: G E 6.1.0-rc3+ #8
pstate: 80400009 (Nzcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : ata_host_stop+0x3c/0x84 [libata]
lr : release_nodes+0x64/0xd0
Call trace:
ata_host_stop+0x3c/0x84 [libata]
release_nodes+0x64/0xd0
devres_release_all+0xbc/0x1b0
device_unbind_cleanup+0x20/0x70
really_probe+0x158/0x320
__driver_probe_device+0x84/0x120
driver_probe_device+0x44/0x120
__driver_attach+0xb4/0x220
bus_for_each_dev+0x78/0xdc
driver_attach+0x2c/0x40
bus_add_driver+0x184/0x240
driver_register+0x80/0x13c
__pci_register_driver+0x4c/0x60
ahci_pci_driver_init+0x30/0x1000 [ahci]
Fix this by removing redundant ata_host_put() in the error path.
Fixes: 2623c7a5f2 ("libata: add refcounting to ata_host")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1610233bc2 ]
The NAND controller size-cells should be 0 per DT bindings.
Fix the following warning produces by DT bindings check:
"
nand-controller@33002000: #size-cells:0:0: 0 was expected
nand-controller@33002000: Unevaluated properties are not allowed ('#address-cells', '#size-cells' were unexpected)
"
Fix the missing space in node name too.
Fixes: a05ea40eb3 ("arm64: dts: imx: Add i.mx8mm dtsi support")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 753395ea1e ]
The NAND controller size-cells should be 0 per DT bindings.
Fix the following warning produces by DT bindings check:
"
nand-controller@33002000: #size-cells:0:0: 0 was expected
nand-controller@33002000: Unevaluated properties are not allowed ('#address-cells', '#size-cells' were unexpected)
"
Fix the missing space in node name too.
Fixes: e7495a45a7 ("ARM: dts: imx7: add GPMI NAND and APBH DMA")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dba9e34674 ]
The drm_atomic_get_new_private_obj_state() function returns NULL
on error path, drm_atomic_get_old_private_obj_state() function
returns NULL on error path, too, they does not return error pointers.
By the way, vc4_hvs_get_new/old_global_state() should return
ERR_PTR(-EINVAL), otherwise there will be null-ptr-defer issue,
such as follows:
In function vc4_atomic_commit_tail():
|-- old_hvs_state = vc4_hvs_get_old_global_state(state); <-- return NULL
|-- if (WARN_ON(IS_ERR(old_hvs_state))) <-- no return
|-- unsigned long state_rate = max(old_hvs_state->core_clock_rate,
new_hvs_state->core_clock_rate); <-- null-ptr-defer
Fixes: 9ec03d7f1e ("drm/vc4: kms: Wait on previous FIFO users before a commit")
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20221110094445.2930509-6-cuigaosheng1@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e63153db5 ]
If device_register() returns error in siox_device_add(),
the name allocated by dev_set_name() need be freed. As
comment of device_register() says, it should use put_device()
to give up the reference in the error path. So fix this
by calling put_device(), then the name can be freed in
kobject_cleanup(), and sdevice is freed in siox_device_release(),
set it to null in error path.
Fixes: bbecb07fa0 ("siox: new driver framework for eckelmann SIOX")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221104021334.618189-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ec8490a19 ]
CONFIG_UBSAN_SHIFT with gcc-5 complains that the shifting of
ARM_CPU_IMP_AMPERE (0xC0) into bits [31:24] by MIDR_CPU_MODEL() is
undefined behavior. Well, sort of, it actually spells the error as:
arch/arm64/kernel/proton-pack.c: In function 'spectre_bhb_loop_affected':
arch/arm64/include/asm/cputype.h:44:2: error: initializer element is not constant
(((imp) << MIDR_IMPLEMENTOR_SHIFT) | \
^
This isn't an issue for other Implementor codes, as all the other codes
have zero in the top bit and so are representable as a signed int.
Cast the implementor code to unsigned in MIDR_CPU_MODEL to remove the
undefined behavior.
Fixes: 0e5d5ae837 ("arm64: Add AMPERE1 to the Spectre-BHB affected list")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: D Scott Phillips <scott@os.amperecomputing.com>
Link: https://lore.kernel.org/r/20221102160106.1096948-1-scott@os.amperecomputing.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb86559a69 ]
kmemleak reports this issue:
unreferenced object 0xffff88817139d000 (size 2048):
comm "test_progs", pid 33246, jiffies 4307381979 (age 45851.820s)
hex dump (first 32 bytes):
01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<0000000045f075f0>] kmalloc_trace+0x27/0xa0
[<0000000098b7c90a>] __check_func_call+0x316/0x1230
[<00000000b4c3c403>] check_helper_call+0x172e/0x4700
[<00000000aa3875b7>] do_check+0x21d8/0x45e0
[<000000001147357b>] do_check_common+0x767/0xaf0
[<00000000b5a595b4>] bpf_check+0x43e3/0x5bc0
[<0000000011e391b1>] bpf_prog_load+0xf26/0x1940
[<0000000007f765c0>] __sys_bpf+0xd2c/0x3650
[<00000000839815d6>] __x64_sys_bpf+0x75/0xc0
[<00000000946ee250>] do_syscall_64+0x3b/0x90
[<0000000000506b7f>] entry_SYSCALL_64_after_hwframe+0x63/0xcd
The root case here is: In function prepare_func_exit(), the callee is
not released in the abnormal scenario after "state->curframe--;". To
fix, move "state->curframe--;" to the very bottom of the function,
right when we free callee and reset frame[] pointer to NULL, as Andrii
suggested.
In addition, function __check_func_call() has a similar problem. In
the abnormal scenario before "state->curframe++;", the callee also
should be released by free_func_state().
Fixes: 69c087ba62 ("bpf: Add bpf_for_each_map_elem() helper")
Fixes: fd978bf7fd ("bpf: Add reference tracking to verifier")
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Link: https://lore.kernel.org/r/1667884291-15666-1-git-send-email-wangyufen@huawei.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f829230dd5 ]
In accordance with [1] the DMA-able memory buffers must be
cacheline-aligned otherwise the cache writing-back and invalidation
performed during the mapping may cause the adjacent data being lost. It's
specifically required for the DMA-noncoherent platforms [2]. Seeing the
opal_dev.{cmd,resp} buffers are implicitly used for DMAs in the NVME and
SCSI/SD drivers in framework of the nvme_sec_submit() and sd_sec_submit()
methods respectively they must be cacheline-aligned to prevent the denoted
problem. One of the option to guarantee that is to kmalloc the buffers
[2]. Let's explicitly allocate them then instead of embedding into the
opal_dev structure instance.
Note this fix was inspired by the commit c94b7f9bab ("nvme-hwmon:
kmalloc the NVME SMART log buffer").
[1] Documentation/core-api/dma-api.rst
[2] Documentation/core-api/dma-api-howto.rst
Fixes: 455a7b238c ("block: Add Sed-opal library")
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20221107203944.31686-1-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d7bebf2df ]
If transport_add_device() fails in sas_phy_add(), the kernel will crash
trying to delete the device in transport_remove_device() called from
sas_remove_host().
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000108
CPU: 61 PID: 42829 Comm: rmmod Kdump: loaded Tainted: G W 6.1.0-rc1+ #173
pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : device_del+0x54/0x3d0
lr : device_del+0x37c/0x3d0
Call trace:
device_del+0x54/0x3d0
attribute_container_class_device_del+0x28/0x38
transport_remove_classdev+0x6c/0x80
attribute_container_device_trigger+0x108/0x110
transport_remove_device+0x28/0x38
sas_phy_delete+0x30/0x60 [scsi_transport_sas]
do_sas_phy_delete+0x6c/0x80 [scsi_transport_sas]
device_for_each_child+0x68/0xb0
sas_remove_children+0x40/0x50 [scsi_transport_sas]
sas_remove_host+0x20/0x38 [scsi_transport_sas]
hisi_sas_remove+0x40/0x68 [hisi_sas_main]
hisi_sas_v2_remove+0x20/0x30 [hisi_sas_v2_hw]
platform_remove+0x2c/0x60
Fix this by checking and handling return value of transport_add_device()
in sas_phy_add().
Fixes: c7ebbbce36 ("[SCSI] SAS transport class")
Suggested-by: John Garry <john.g.garry@oracle.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221107124828.115557-1-yangyingliang@huawei.com
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bee55f2e7a ]
The mux routes are incomplete for the PX30. This was discovered because
we had a HW design using cif-clkoutm1 with the correct pinmux in the
Device Tree but the clock would still not work.
There are actually two muxing required: the pin muxing (performed by the
usual Device Tree pinctrl nodes) and the "function" muxing (m0 vs m1;
performed by the mux routing inside the driver). The pin muxing was
correct but the function muxing was not.
This adds the missing pins and their configuration for the mux routes
that are already specified in the driver.
Note that there are some "conflicts": it is possible *in Device Tree* to
(attempt to) mux the pins for e.g. clkoutm1 and clkinm0 at the same time
but this is actually not possible in hardware (because both share the
same bit for the function muxing). Since it is an impossible hardware
design, it is not deemed necessary to prevent the user from attempting
to "misconfigure" the pins/functions.
Fixes: 87065ca9b8 ("pinctrl: rockchip: Add pinctrl support for PX30")
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Link: https://lore.kernel.org/r/20221017-upstream-px30-cif-clkoutm1-v1-0-4ea1389237f7@theobroma-systems.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 314d34fe7f ]
snd_soc_util_exit() is called in __init snd_soc_init() for cleanup.
Remove the __exit annotation for it to fix the build warning:
WARNING: modpost: sound/soc/snd-soc-core.o: section mismatch in reference: init_module (section: .init.text) -> snd_soc_util_exit (section: .exit.text)
Fixes: 6ec27c5388 ("ASoC: core: Fix use-after-free in snd_soc_exit()")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Link: https://lore.kernel.org/r/20221031134031.256511-1-chenzhongjin@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3fd203f36 ]
We got a syzkaller problem because of aarch64 alignment fault
if KFENCE enabled. When the size from user bpf program is an odd
number, like 399, 407, etc, it will cause the struct skb_shared_info's
unaligned access. As seen below:
BUG: KFENCE: use-after-free read in __skb_clone+0x23c/0x2a0 net/core/skbuff.c:1032
Use-after-free read at 0xffff6254fffac077 (in kfence-#213):
__lse_atomic_add arch/arm64/include/asm/atomic_lse.h:26 [inline]
arch_atomic_add arch/arm64/include/asm/atomic.h:28 [inline]
arch_atomic_inc include/linux/atomic-arch-fallback.h:270 [inline]
atomic_inc include/asm-generic/atomic-instrumented.h:241 [inline]
__skb_clone+0x23c/0x2a0 net/core/skbuff.c:1032
skb_clone+0xf4/0x214 net/core/skbuff.c:1481
____bpf_clone_redirect net/core/filter.c:2433 [inline]
bpf_clone_redirect+0x78/0x1c0 net/core/filter.c:2420
bpf_prog_d3839dd9068ceb51+0x80/0x330
bpf_dispatcher_nop_func include/linux/bpf.h:728 [inline]
bpf_test_run+0x3c0/0x6c0 net/bpf/test_run.c:53
bpf_prog_test_run_skb+0x638/0xa7c net/bpf/test_run.c:594
bpf_prog_test_run kernel/bpf/syscall.c:3148 [inline]
__do_sys_bpf kernel/bpf/syscall.c:4441 [inline]
__se_sys_bpf+0xad0/0x1634 kernel/bpf/syscall.c:4381
kfence-#213: 0xffff6254fffac000-0xffff6254fffac196, size=407, cache=kmalloc-512
allocated by task 15074 on cpu 0 at 1342.585390s:
kmalloc include/linux/slab.h:568 [inline]
kzalloc include/linux/slab.h:675 [inline]
bpf_test_init.isra.0+0xac/0x290 net/bpf/test_run.c:191
bpf_prog_test_run_skb+0x11c/0xa7c net/bpf/test_run.c:512
bpf_prog_test_run kernel/bpf/syscall.c:3148 [inline]
__do_sys_bpf kernel/bpf/syscall.c:4441 [inline]
__se_sys_bpf+0xad0/0x1634 kernel/bpf/syscall.c:4381
__arm64_sys_bpf+0x50/0x60 kernel/bpf/syscall.c:4381
To fix the problem, we adjust @size so that (@size + @hearoom) is a
multiple of SMP_CACHE_BYTES. So we make sure the struct skb_shared_info
is aligned to a cache line.
Fixes: 1cf1cae963 ("bpf: introduce BPF_PROG_TEST_RUN command")
Signed-off-by: Baisong Zhong <zhongbaisong@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/bpf/20221102081620.1465154-1-zhongbaisong@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b7dfe4833 ]
The function gsm_dlci_t1() is a timer handler that runs in an
atomic context, but it calls "kzalloc(..., GFP_KERNEL)" that
may sleep. As a result, the sleep-in-atomic-context bug will
happen. The process is shown below:
gsm_dlci_t1()
gsm_dlci_open()
gsm_modem_update()
gsm_modem_upd_via_msc()
gsm_control_send()
kzalloc(sizeof(.., GFP_KERNEL) //may sleep
This patch changes the gfp_t parameter of kzalloc() from GFP_KERNEL to
GFP_ATOMIC in order to mitigate the bug.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/20221002040709.27849-1-duoming@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d0b68629bd ]
Rebinding 8250_omap in a loop will at some point produce a warning for
kernel/power/qos.c:296 cpu_latency_qos_update_request() with error
"cpu_latency_qos_update_request called for unknown object". Let's flush
the possibly pending PM QOS work scheduled from omap8250_runtime_suspend()
before we disable runtime PM.
Fixes: 61929cf016 ("tty: serial: Add 8250-core based omap driver")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20221028110044.54719-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3f0c638f4 ]
On remove, we get an error for "Runtime PM usage count underflow!". I guess
this driver is mostly built-in, and this issue has gone unnoticed for a
while. Somehow I did not catch this issue with my earlier fix done with
commit 4e0f5cc650 ("serial: 8250_omap: Fix probe and remove for PM
runtime").
Fixes: 4e0f5cc650 ("serial: 8250_omap: Fix probe and remove for PM runtime")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Depends-on: dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
Link: https://lore.kernel.org/r/20221028105813.54290-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e828e56684 ]
We were occasionally seeing the "Errata i202: timedout" on an AM335x
board when repeatedly opening and closing a UART connected to an active
sender. As new input may arrive at any time, it is possible to miss the
"RX FIFO empty" condition, forcing the loop to wait until it times out.
Nothing in the i202 Advisory states that such a wait is even necessary;
other FIFO clear functions like serial8250_clear_fifos() do not wait
either. For this reason, it seems safe to remove the wait, fixing the
mentioned issue.
Fixes: 61929cf016 ("tty: serial: Add 8250-core based omap driver")
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20221013112339.2540767-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 93810191f5 ]
There are cases where omap8250_set_mctrl() may get called after the
UART has already autoidled causing an asynchronous external abort.
This can happen on ttyport_open():
mem_serial_in from omap8250_set_mctrl+0x38/0xa0
omap8250_set_mctrl from uart_update_mctrl+0x4c/0x58
uart_update_mctrl from uart_dtr_rts+0x60/0xa8
uart_dtr_rts from tty_port_block_til_ready+0xd0/0x2a8
tty_port_block_til_ready from uart_open+0x14/0x1c
uart_open from ttyport_open+0x64/0x148
And on ttyport_close():
omap8250_set_mctrl from uart_update_mctrl+0x3c/0x48
uart_update_mctrl from uart_dtr_rts+0x54/0x9c
uart_dtr_rts from tty_port_shutdown+0x78/0x9c
tty_port_shutdown from tty_port_close+0x3c/0x74
tty_port_close from ttyport_close+0x40/0x58
It can also happen on disassociate_ctty() calling uart_shutdown()
that ends up calling omap8250_set_mctrl().
Let's fix the issue by adding missing PM runtime calls to
omap8250_set_mctrl(). To do this, we need to add __omap8250_set_mctrl()
that can be called from both omap8250_set_mctrl(), and from runtime PM
resume path when restoring the registers.
Fixes: 61929cf016 ("tty: serial: Add 8250-core based omap driver")
Reported-by: Merlijn Wajer <merlijn@wizzup.org>
Reported-by: Romain Naour <romain.naour@smile.fr>
Reported-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Tested-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Depends-on: dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
Link: https://lore.kernel.org/r/20221024063613.25943-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit faac764ea1 ]
There's a special branch in the set_tdm_slot op for the case of nslots
being 1, but:
(1) That branch can never work (there's a check for tx_mask being
non-zero, later there's another check for it *being* zero; one or
the other always throws -EINVAL).
(2) The intention of the branch seems to be what the general other
branch reduces to in case of nslots being 1.
For those reasons remove the 'nslots being 1' special case.
Fixes: 827ed8a0fa ("ASoC: tas2764: Add the driver for the TAS2764")
Suggested-by: Jos Dehaes <jos.dehaes@gmail.com>
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20221027095800.16094-2-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e59bf547a7 ]
There's a special branch in the set_tdm_slot op for the case of nslots
being 1, but:
(1) That branch can never work (there's a check for tx_mask being
non-zero, later there's another check for it *being* zero; one or
the other always throws -EINVAL).
(2) The intention of the branch seems to be what the general other
branch reduces to in case of nslots being 1.
For those reasons remove the 'nslots being 1' special case.
Fixes: 1a476abc72 ("tas2770: add tas2770 smart PA kernel driver")
Suggested-by: Jos Dehaes <jos.dehaes@gmail.com>
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20221027095800.16094-1-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ec27c5388 ]
KASAN reports a use-after-free:
BUG: KASAN: use-after-free in device_del+0xb5b/0xc60
Read of size 8 at addr ffff888008655050 by task rmmod/387
CPU: 2 PID: 387 Comm: rmmod
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996)
Call Trace:
<TASK>
dump_stack_lvl+0x79/0x9a
print_report+0x17f/0x47b
kasan_report+0xbb/0xf0
device_del+0xb5b/0xc60
platform_device_del.part.0+0x24/0x200
platform_device_unregister+0x2e/0x40
snd_soc_exit+0xa/0x22 [snd_soc_core]
__do_sys_delete_module.constprop.0+0x34f/0x5b0
do_syscall_64+0x3a/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
...
</TASK>
It's bacause in snd_soc_init(), snd_soc_util_init() is possble to fail,
but its ret is ignored, which makes soc_dummy_dev unregistered twice.
snd_soc_init()
snd_soc_util_init()
platform_device_register_simple(soc_dummy_dev)
platform_driver_register() # fail
platform_device_unregister(soc_dummy_dev)
platform_driver_register() # success
...
snd_soc_exit()
snd_soc_util_exit()
# soc_dummy_dev will be unregistered for second time
To fix it, handle error and stop snd_soc_init() when util_init() fail.
Also clean debugfs when util_init() or driver_register() fail.
Fixes: fb257897bf ("ASoC: Work around allmodconfig failure")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Link: https://lore.kernel.org/r/20221028031603.59416-1-chenzhongjin@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 195583504b ]
The original fix "spi: stm32: Rate-limit the 'Communication suspended' message"
still leads to "stm32h7_spi_irq_thread: 1696 callbacks suppressed" spew in the
kernel log. Since this 'Communication suspended' message is a debug print, add
RATELIMIT_MSG_ON_RELEASE flag to inhibit the "callbacks suspended" part during
normal operation and only print summary at the end.
Fixes: ea8be08cc9 ("spi: stm32: Rate-limit the 'Communication suspended' message")
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20221018183513.206706-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8625147caf ]
This change is very similar to the change that was made for shmem [1], and
it solves the same problem but for HugeTLBFS instead.
Currently, when poison is found in a HugeTLB page, the page is removed
from the page cache. That means that attempting to map or read that
hugepage in the future will result in a new hugepage being allocated
instead of notifying the user that the page was poisoned. As [1] states,
this is effectively memory corruption.
The fix is to leave the page in the page cache. If the user attempts to
use a poisoned HugeTLB page with a syscall, the syscall will fail with
EIO, the same error code that shmem uses. For attempts to map the page,
the thread will get a BUS_MCEERR_AR SIGBUS.
[1]: commit a760542666 ("mm: shmem: don't truncate page if memory failure happens")
Link: https://lkml.kernel.org/r/20221018200125.848471-1-jthoughton@google.com
Signed-off-by: James Houghton <jthoughton@google.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Reviewed-by: Naoya Horiguchi <naoya.horiguchi@nec.com>
Tested-by: Naoya Horiguchi <naoya.horiguchi@nec.com>
Reviewed-by: Yang Shi <shy828301@gmail.com>
Cc: Axel Rasmussen <axelrasmussen@google.com>
Cc: James Houghton <jthoughton@google.com>
Cc: Miaohe Lin <linmiaohe@huawei.com>
Cc: Muchun Song <songmuchun@bytedance.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8631ef59b6 ]
The SDM lists an architectural MSR IA32_CORE_CAPABILITIES (0xCF)
that limits the theoretical maximum value of the Intel GP PMC MSRs
allocated at 0xC1 to 14; likewise the Intel April 2022 SDM adds
IA32_OVERCLOCKING_STATUS at 0x195 which limits the number of event
selection MSRs to 15 (0x186-0x194).
Limiting the maximum number of counters to 14 or 18 based on the currently
allocated MSRs is clearly fragile, and it seems likely that Intel will
even place PMCs 8-15 at a completely different range of MSR indices.
So stop at the maximum number of GP PMCs supported today on Intel
processors.
There are some machines, like Intel P4 with non Architectural PMU, that
may indeed have 18 counters, but those counters are in a completely
different MSR address range and are not supported by KVM.
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: stable@vger.kernel.org
Fixes: cf05a67b68 ("KVM: x86: omit "impossible" pmu MSRs from MSR list")
Suggested-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Like Xu <likexu@tencent.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Message-Id: <20220919091008.60695-1-likexu@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f937b758a1 ]
l2cap_global_chan_by_psm shall not return fixed channels as they are not
meant to be connected by (S)PSM.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Reviewed-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d0ea17aec1 ]
Several places in the qgroup self tests follow the pattern of freeing the
ulist pointer they passed to btrfs_find_all_roots() if the call to that
function returned an error. That is pointless because that function always
frees the ulist in case it returns an error.
Also In some places like at test_multiple_refs(), after a call to
btrfs_qgroup_account_extent() we also leave "old_roots" and "new_roots"
pointing to ulists that were freed, because btrfs_qgroup_account_extent()
has freed those ulists, and if after that the next call to
btrfs_find_all_roots() fails, we call ulist_free() on the "old_roots"
ulist again, resulting in a double free.
So remove those calls to reduce the code size and avoid double ulist
free in case of an error.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d6643d7207 ]
Dell Vostro 5568 laptop has lis3lv02d, but its i2c address is not known
to the kernel. Add this address.
Output of "cat /sys/devices/platform/lis3lv02d/position" on Dell Vostro
5568 laptop:
- Horizontal: (-18,0,1044)
- Front elevated: (522,-18,1080)
- Left elevated: (-18,-360,1080)
- Upside down: (36,108,-1134)
Signed-off-by: Nam Cao <namcaov@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cdbf26251d ]
When the I2C controllers are running in DMA mode, it is the DMA engine
that performs the memory accesses rather than the I2C controller. Pass
the DMA engine's struct device pointer to the DMA API to make sure the
correct DMA operations are used.
This fixes an issue where the DMA engine's SMMU stream ID needs to be
misleadingly set for the I2C controllers in device tree.
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f4071cbd2 ]
Platform drivers .remove callbacks are not supposed to fail and report
errors. Such errors are indeed ignored by the core platform drivers
and the driver unbind process is anyway completed.
The SCMI core platform driver as it is now, instead, bails out reporting
an error in case of an explicit unbind request.
Fix the removal path by adding proper device links between the core SCMI
device and the SCMI protocol devices so that a full SCMI stack unbind is
triggered when the core driver is removed. The remove process does not
bail out anymore on the anomalous conditions triggered by an explicit
unbind but the user is still warned.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20221028140833.280091-1-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f5ea16137a ]
There's a small window where a LOCK sent during a delegation return can
race with another OPEN on client, but the open stateid has not yet been
updated. In this case, the client doesn't handle the OLD_STATEID error
from the server and will lose this lock, emitting:
"NFS: nfs4_handle_delegation_recall_error: unhandled error -10024".
Fix this by sending the task through the nfs4 error handling in
nfs4_lock_done() when we may have to reconcile our stateid with what the
server believes it to be. For this case, the result is a retry of the
LOCK operation with the updated stateid.
Reported-by: Gonzalo Siero Humet <gsierohu@redhat.com>
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f15fb2cd97 ]
In raid56_alloc_missing_rbio(), if we can not determine where the
missing device is inside the full stripe, we just BUG_ON().
This is not necessary especially the only caller inside scrub.c is
already properly checking the return value, and will treat it as a
memory allocation failure.
Fix the error handling by:
- Add an extra warning for the reason
Although personally speaking it may be better to be an ASSERT().
- Properly free the allocated rbio
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa153b7cdd ]
Some x86/ACPI laptops with MIPI cameras have a LATT2021 ACPI device
in the _DEP dependency list of the ACPI devices for the camera-sensors
(which have flags.honor_deps set).
The _DDN for the LATT2021 device is "Lattice FW Update Client Driver",
suggesting that this is used for firmware updates of something. There
is no Linux driver for this and if Linux gets support for updates it
will likely be in userspace through fwupd.
For now add the LATT2021 HID to acpi_ignore_dep_ids[] so that
acpi_dev_ready_for_enumeration() will return true once the other _DEP
dependencies are met.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca08a1725d ]
When using a device based on DCN32/321,
we have an issue where a second
4k@60Hz display does not light up,
and the system becomes unresponsive
for a few minutes. In the debug process,
it was possible to see a hang
in the function dcn20_post_unlock_program_front_end
in this part:
for (j = 0; j < TIMEOUT_FOR_PIPE_ENABLE_MS*1000
&& hubp->funcs->hubp_is_flip_pending(hubp); j++)
mdelay(1);
}
The hubp_is_flip_pending always returns positive
for waiting pending flips which is a symptom of
pipe hang. Additionally, the dmesg log shows
this message after a few minutes:
BUG: soft lockup - CPU#4 stuck for 26s!
...
[ +0.000003] dcn20_post_unlock_program_front_end+0x112/0x340 [amdgpu]
[ +0.000171] dc_commit_state_no_check+0x63d/0xbf0 [amdgpu]
[ +0.000155] ? dc_validate_global_state+0x358/0x3d0 [amdgpu]
[ +0.000154] dc_commit_state+0xe2/0xf0 [amdgpu]
This confirmed the hypothesis that we had a pipe
hanging somewhere. Next, after checking the
ftrace entries, we have the below weird
sequence:
[..]
2) | dcn10_lock_all_pipes [amdgpu]() {
2) 0.120 us | optc1_is_tg_enabled [amdgpu]();
2) | dcn20_pipe_control_lock [amdgpu]() {
2) | dc_dmub_srv_clear_inbox0_ack [amdgpu]() {
2) 0.121 us | amdgpu_dm_dmub_reg_write [amdgpu]();
2) 0.551 us | }
2) | dc_dmub_srv_send_inbox0_cmd [amdgpu]() {
2) 0.110 us | amdgpu_dm_dmub_reg_write [amdgpu]();
2) 0.511 us | }
2) | dc_dmub_srv_wait_for_inbox0_ack [amdgpu]() {
2) 0.110 us | amdgpu_dm_dmub_reg_read [amdgpu]();
2) 0.110 us | amdgpu_dm_dmub_reg_read [amdgpu]();
2) 0.110 us | amdgpu_dm_dmub_reg_read [amdgpu]();
2) 0.110 us | amdgpu_dm_dmub_reg_read [amdgpu]();
2) 0.110 us | amdgpu_dm_dmub_reg_read [amdgpu]();
2) 0.110 us | amdgpu_dm_dmub_reg_read [amdgpu]();
2) 0.110 us | amdgpu_dm_dmub_reg_read [amdgpu]();
[..]
We are not expected to read from dmub register
so many times and for so long. From the trace log,
it was possible to identify that the function
dcn20_pipe_control_lock was triggering the dmub
operation when it was unnecessary and causing
the hang issue. This commit drops the unnecessary
dmub code and, consequently, fixes the second display not
lighting up the issue.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03cab65a07 ]
Don't use the test-specific header files as source files to force a
target dependency, as clang will complain if more than one source file
is used for a compile command with a single '-o' flag.
Use the proper Makefile variables instead as defined in
tools/testing/selftests/lib.mk.
Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
Reviewed-by: André Almeida <andrealmeid@igalia.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1538e2c8c9 ]
Line In Bypass control is used as Master Capture at the moment
this is completely incorrect.
Current control routed to Mixer instead of ADC, thus can't affect
Capture path. ADC control shall be used instead.
ADC volume control parameters are different, so the patch fixes that
as well. Manual says (16.6.3.2 Programmable input attenuation amplifier:
PGATM) that gain varies in range 0dB..22.5dB with 1.5dB step.
Signed-off-by: Siarhei Volkau <lis8215@gmail.com>
Link: https://lore.kernel.org/r/20221016132648.3011729-4-lis8215@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 088777bf65 ]
DAC volume control is the Master Playback Volume at the moment
and it reports wrong levels in alsamixer and other alsa apps.
The patch fixes that, as stated in manual on the jz4725b SoC
(16.6.3.4 Programmable attenuation: GOD) the ctl range varies
from -22.5dB to 0dB with 1.5dB step.
Signed-off-by: Siarhei Volkau <lis8215@gmail.com>
Link: https://lore.kernel.org/r/20221016132648.3011729-3-lis8215@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee1aa2ae3e ]
In wm8962 driver, the WM8962_ADDITIONAL_CONTROL_4 is used as a volatile
register, but this register mixes a bunch of volatile status bits and a
bunch of non-volatile control bits. The dapm widgets TEMP_HP and
TEMP_SPK leverages the control bits in this register. After the wm8962
probe, the regmap will bet set to cache only mode, then a read error
like below would be triggered when trying to read the initial power
state of the dapm widgets TEMP_HP and TEMP_SPK.
wm8962 0-001a: ASoC: error at soc_component_read_no_lock
on wm8962.0-001a: -16
In order to fix this issue, we add event handler to actually power
up/down these widgets. With this change, we also need to explicitly
power off these widgets in the wm8962 probe since they are enabled
by default.
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Tested-by: Adam Ford <aford173@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221010092014.2229246-1-xiaolei.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Although disabling the SMBUS timeout may be useful, not all chips
support it. The driver treats attempting to disable the timeout on a
non-supporting chip as an error, so make it an option enabled using the
no_timeout parameter.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Add the alt function selectors, and document that pins_40_45 is not
suitable for BCM2711 because the pins are split across the two PWM
interfaces.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
commit 3a87606089 upstream.
migrate_vma_setup shows below warning because we don't hold another
process mm mmap_lock. We should use current vmf->vma->vm_mm instead, the
caller already hold current mmap lock inside CPU page fault handler.
WARNING: CPU: 10 PID: 3054 at include/linux/mmap_lock.h:155 find_vma
Call Trace:
walk_page_range+0x76/0x150
migrate_vma_setup+0x18a/0x640
svm_migrate_vram_to_ram+0x245/0xa10 [amdgpu]
svm_migrate_to_ram+0x36f/0x470 [amdgpu]
do_swap_page+0xcfe/0xec0
__handle_mm_fault+0x96b/0x15e0
handle_mm_fault+0x13f/0x3e0
do_user_addr_fault+0x1e7/0x690
Fixes: e1f84eef31 ("drm/amdkfd: handle CPU fault on COW mapping")
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6312d52838 upstream.
Building an allmodconfig kernel arm64 kernel, the following build error
shows up:
In file included from drivers/crypto/marvell/octeontx2/cn10k_cpt.c:4:
include/linux/soc/marvell/octeontx2/asm.h:38:15: error: unknown type name 'u64'
38 | static inline u64 otx2_atomic64_fetch_add(u64 incr, u64 *ptr)
| ^~~
Include linux/types.h in asm.h so the compiler knows what the type
'u64' are.
Fixes: af3826db74 ("octeontx2-pf: Use hardware register for CQE count")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Link: https://lore.kernel.org/r/20211013135743.3826594-1-anders.roxell@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6bfb56e93b upstream.
OpenSSL 3.0 deprecated the OpenSSL's ENGINE API. That is as may be, but
the kernel build host tools still use it. Disable the warning about
deprecated declarations until somebody who cares fixes it.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 93b0d91787 upstream.
mfill_atomic_install_pte() checks page->mapping to detect whether one page
is used in the page cache. However as pointed out by Matthew, the page
can logically be a tail page rather than always the head in the case of
uffd minor mode with UFFDIO_CONTINUE. It means we could wrongly install
one pte with shmem thp tail page assuming it's an anonymous page.
It's not that clear even for anonymous page, since normally anonymous
pages also have page->mapping being setup with the anon vma. It's safe
here only because the only such caller to mfill_atomic_install_pte() is
always passing in a newly allocated page (mcopy_atomic_pte()), whose
page->mapping is not yet setup. However that's not extremely obvious
either.
For either of above, use page_mapping() instead.
Link: https://lkml.kernel.org/r/Y2K+y7wnhC4vbnP2@x1n
Fixes: 153132571f ("userfaultfd/shmem: support UFFDIO_CONTINUE for shmem")
Signed-off-by: Peter Xu <peterx@redhat.com>
Reported-by: Matthew Wilcox <willy@infradead.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Axel Rasmussen <axelrasmussen@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c8af247de3 upstream.
Syzbot reported a slab-out-of-bounds Write bug:
loop0: detected capacity change from 0 to 2048
==================================================================
BUG: KASAN: slab-out-of-bounds in udf_find_entry+0x8a5/0x14f0
fs/udf/namei.c:253
Write of size 105 at addr ffff8880123ff896 by task syz-executor323/3610
CPU: 0 PID: 3610 Comm: syz-executor323 Not tainted
6.1.0-rc2-syzkaller-00105-gb229b6ca5abb #0
Hardware name: Google Compute Engine/Google Compute Engine, BIOS
Google 10/11/2022
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x1b1/0x28e lib/dump_stack.c:106
print_address_description+0x74/0x340 mm/kasan/report.c:284
print_report+0x107/0x1f0 mm/kasan/report.c:395
kasan_report+0xcd/0x100 mm/kasan/report.c:495
kasan_check_range+0x2a7/0x2e0 mm/kasan/generic.c:189
memcpy+0x3c/0x60 mm/kasan/shadow.c:66
udf_find_entry+0x8a5/0x14f0 fs/udf/namei.c:253
udf_lookup+0xef/0x340 fs/udf/namei.c:309
lookup_open fs/namei.c:3391 [inline]
open_last_lookups fs/namei.c:3481 [inline]
path_openat+0x10e6/0x2df0 fs/namei.c:3710
do_filp_open+0x264/0x4f0 fs/namei.c:3740
do_sys_openat2+0x124/0x4e0 fs/open.c:1310
do_sys_open fs/open.c:1326 [inline]
__do_sys_creat fs/open.c:1402 [inline]
__se_sys_creat fs/open.c:1396 [inline]
__x64_sys_creat+0x11f/0x160 fs/open.c:1396
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
RIP: 0033:0x7ffab0d164d9
Code: ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89
f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01
f0 ff ff 73 01 c3 48 c7 c1 c0 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007ffe1a7e6bb8 EFLAGS: 00000246 ORIG_RAX: 0000000000000055
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007ffab0d164d9
RDX: 00007ffab0d164d9 RSI: 0000000000000000 RDI: 0000000020000180
RBP: 00007ffab0cd5a10 R08: 0000000000000000 R09: 0000000000000000
R10: 00005555573552c0 R11: 0000000000000246 R12: 00007ffab0cd5aa0
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
</TASK>
Allocated by task 3610:
kasan_save_stack mm/kasan/common.c:45 [inline]
kasan_set_track+0x3d/0x60 mm/kasan/common.c:52
____kasan_kmalloc mm/kasan/common.c:371 [inline]
__kasan_kmalloc+0x97/0xb0 mm/kasan/common.c:380
kmalloc include/linux/slab.h:576 [inline]
udf_find_entry+0x7b6/0x14f0 fs/udf/namei.c:243
udf_lookup+0xef/0x340 fs/udf/namei.c:309
lookup_open fs/namei.c:3391 [inline]
open_last_lookups fs/namei.c:3481 [inline]
path_openat+0x10e6/0x2df0 fs/namei.c:3710
do_filp_open+0x264/0x4f0 fs/namei.c:3740
do_sys_openat2+0x124/0x4e0 fs/open.c:1310
do_sys_open fs/open.c:1326 [inline]
__do_sys_creat fs/open.c:1402 [inline]
__se_sys_creat fs/open.c:1396 [inline]
__x64_sys_creat+0x11f/0x160 fs/open.c:1396
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
The buggy address belongs to the object at ffff8880123ff800
which belongs to the cache kmalloc-256 of size 256
The buggy address is located 150 bytes inside of
256-byte region [ffff8880123ff800, ffff8880123ff900)
The buggy address belongs to the physical page:
page:ffffea000048ff80 refcount:1 mapcount:0 mapping:0000000000000000
index:0x0 pfn:0x123fe
head:ffffea000048ff80 order:1 compound_mapcount:0 compound_pincount:0
flags: 0xfff00000010200(slab|head|node=0|zone=1|lastcpupid=0x7ff)
raw: 00fff00000010200 ffffea00004b8500 dead000000000003 ffff888012041b40
raw: 0000000000000000 0000000080100010 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
page_owner tracks the page as allocated
page last allocated via order 0, migratetype Unmovable, gfp_mask 0x0(),
pid 1, tgid 1 (swapper/0), ts 1841222404, free_ts 0
create_dummy_stack mm/page_owner.c:67 [inline]
register_early_stack+0x77/0xd0 mm/page_owner.c:83
init_page_owner+0x3a/0x731 mm/page_owner.c:93
kernel_init_freeable+0x41c/0x5d5 init/main.c:1629
kernel_init+0x19/0x2b0 init/main.c:1519
page_owner free stack trace missing
Memory state around the buggy address:
ffff8880123ff780: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff8880123ff800: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>ffff8880123ff880: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 06
^
ffff8880123ff900: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff8880123ff980: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
==================================================================
Fix this by changing the memory size allocated for copy_name from
UDF_NAME_LEN(254) to UDF_NAME_LEN_CS0(255), because the total length
(lfi) of subsequent memcpy can be up to 255.
CC: stable@vger.kernel.org
Reported-by: syzbot+69c9fdccc6dd08961d34@syzkaller.appspotmail.com
Fixes: 066b9cded0 ("udf: Use separate buffer for copying split names")
Signed-off-by: ZhangPeng <zhangpeng362@huawei.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20221109013542.442790-1-zhangpeng362@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb1dec44c6 upstream.
[[ NOTE: this is completely untested by the author, but included solely
because, as noted in commit df57d73276 ("mmc: sdhci-pci: Fix
SDHCI_RESET_ALL for CQHCI for Intel GLK-based controllers"), "other
drivers using CQHCI might benefit from a similar change, if they
also have CQHCI reset by SDHCI_RESET_ALL." We've now seen the same
bug on at least MSM, Arasan, and Intel hardware. ]]
SDHCI_RESET_ALL resets will reset the hardware CQE state, but we aren't
tracking that properly in software. When out of sync, we may trigger
various timeouts.
It's not typical to perform resets while CQE is enabled, but this may
occur in some suspend or error recovery scenarios.
Include this fix by way of the new sdhci_and_cqhci_reset() helper.
This patch depends on (and should not compile without) the patch
entitled "mmc: cqhci: Provide helper for resetting both SDHCI and
CQHCI".
Fixes: bb6e358169 ("mmc: sdhci-esdhc-imx: add CMDQ support")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221026124150.v4.4.I7d01f9ad11bacdc9213dee61b7918982aea39115@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8d1b1647b upstream.
When performing seeding on a zoned filesystem it is necessary to
initialize each zoned device's btrfs_zoned_device_info structure,
otherwise mounting the filesystem will cause a NULL pointer dereference.
This was uncovered by fstests' testcase btrfs/163.
CC: stable@vger.kernel.org # 5.15+
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0fca385d6e upstream.
syzkaller found a failed assertion:
assertion failed: (args->devid != (u64)-1) || args->missing, in fs/btrfs/volumes.c:6921
This can be triggered when we set devid to (u64)-1 by ioctl. In this
case, the match of devid will be skipped and the match of device may
succeed incorrectly.
Patch 562d7b1512 introduced this function which is used to match device.
This function contains two matching scenarios, we can distinguish them by
checking the value of args->missing rather than check whether args->devid
and args->uuid is default value.
Reported-by: syzbot+031687116258450f9853@syzkaller.appspotmail.com
Fixes: 562d7b1512 ("btrfs: handle device lookup with btrfs_dev_lookup_args")
CC: stable@vger.kernel.org # 5.16+
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f45cb6b29c upstream.
(cherry picked from commit d99884ad9e in ath-next
as users are seeing this bug more now, also cc stable)
Running this test in a loop it is easy to reproduce an rtnl deadlock:
iw reg set FI
ifconfig wlan0 down
What happens is that thread A (workqueue) tries to update the regulatory:
try to acquire the rtnl_lock of ar->regd_update_work
rtnl_lock+0x17/0x20
ath11k_regd_update+0x15a/0x260 [ath11k]
ath11k_regd_update_work+0x15/0x20 [ath11k]
process_one_work+0x228/0x670
worker_thread+0x4d/0x440
kthread+0x16d/0x1b0
ret_from_fork+0x22/0x30
And thread B (ifconfig) tries to stop the interface:
try to cancel_work_sync(&ar->regd_update_work) in ath11k_mac_op_stop().
ifconfig 3109 [003] 2414.232506: probe:
ath11k_mac_op_stop: (ffffffffc14187a0)
drv_stop+0x30 ([mac80211])
ieee80211_do_stop+0x5d2 ([mac80211])
ieee80211_stop+0x3e ([mac80211])
__dev_close_many+0x9e ([kernel.kallsyms])
__dev_change_flags+0xbe ([kernel.kallsyms])
dev_change_flags+0x23 ([kernel.kallsyms])
devinet_ioctl+0x5e3 ([kernel.kallsyms])
inet_ioctl+0x197 ([kernel.kallsyms])
sock_do_ioctl+0x4d ([kernel.kallsyms])
sock_ioctl+0x264 ([kernel.kallsyms])
__x64_sys_ioctl+0x92 ([kernel.kallsyms])
do_syscall_64+0x3a ([kernel.kallsyms])
entry_SYSCALL_64_after_hwframe+0x63 ([kernel.kallsyms])
__GI___ioctl+0x7 (/lib/x86_64-linux-gnu/libc-2.23.so)
The sequence of deadlock is:
1. Thread B calls rtnl_lock().
2. Thread A starts to run and calls rtnl_lock() from within
ath11k_regd_update_work(), then enters wait state because the lock is owned by
thread B.
3. Thread B continues to run and tries to call
cancel_work_sync(&ar->regd_update_work), but thread A is in
ath11k_regd_update_work() waiting for rtnl_lock(). So cancel_work_sync()
forever waits for ath11k_regd_update_work() to finish and we have a deadlock.
Fix this by switching from using regulatory_set_wiphy_regd_sync() to
regulatory_set_wiphy_regd(). Now cfg80211 will schedule another workqueue which
handles the locking on it's own. So the ath11k workqueue can simply exit without
taking any locks, avoiding the deadlock.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Cc: <stable@vger.kernel.org>
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
[kvalo: improve commit log]
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1598bfa8e1 upstream.
After upgrading BIOS to U82 01.02.01 Rev.A, the console is flooded
strange char "^@" which printed out every second and makes login
nearly impossible. Also the below messages were shown both in console
and journal/dmesg every second:
usb 1-3: Device not responding to setup address.
usb 1-3: device not accepting address 4, error -71
usb 1-3: device descriptor read/all, error -71
usb usb1-port3: unable to enumerate USB device
Wifi is soft blocked by checking rfkill. When unblocked manually,
after few seconds it would be soft blocked again. So I was suspecting
something triggered rfkill to soft block wifi. At the end it was
fixed by removing hp_wmi module.
The root cause is the way hp-wmi driver handles command 1B on
post-2009 BIOS. In pre-2009 BIOS, command 1Bh return 0x4 to indicate
that BIOS no longer controls the power for the wireless devices.
Signed-off-by: Jorge Lopez <jorge.lopez2@hp.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216468
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20221028155527.7724-1-jorge.lopez2@hp.com
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8cccf05fe8 upstream.
If a nilfs2 filesystem is downgraded to read-only due to metadata
corruption on disk and is remounted read/write, or if emergency read-only
remount is performed, detaching a log writer and synchronizing the
filesystem can be done at the same time.
In these cases, use-after-free of the log writer (hereinafter
nilfs->ns_writer) can happen as shown in the scenario below:
Task1 Task2
-------------------------------- ------------------------------
nilfs_construct_segment
nilfs_segctor_sync
init_wait
init_waitqueue_entry
add_wait_queue
schedule
nilfs_remount (R/W remount case)
nilfs_attach_log_writer
nilfs_detach_log_writer
nilfs_segctor_destroy
kfree
finish_wait
_raw_spin_lock_irqsave
__raw_spin_lock_irqsave
do_raw_spin_lock
debug_spin_lock_before <-- use-after-free
While Task1 is sleeping, nilfs->ns_writer is freed by Task2. After Task1
waked up, Task1 accesses nilfs->ns_writer which is already freed. This
scenario diagram is based on the Shigeru Yoshida's post [1].
This patch fixes the issue by not detaching nilfs->ns_writer on remount so
that this UAF race doesn't happen. Along with this change, this patch
also inserts a few necessary read-only checks with superblock instance
where only the ns_writer pointer was used to check if the filesystem is
read-only.
Link: https://syzkaller.appspot.com/bug?id=79a4c002e960419ca173d55e863bd09e8112df8b
Link: https://lkml.kernel.org/r/20221103141759.1836312-1-syoshida@redhat.com [1]
Link: https://lkml.kernel.org/r/20221104142959.28296-1-konishi.ryusuke@gmail.com
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Reported-by: syzbot+f816fa82f8783f7a02bb@syzkaller.appspotmail.com
Reported-by: Shigeru Yoshida <syoshida@redhat.com>
Tested-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ac932a492 upstream.
A semaphore deadlock can occur if nilfs_get_block() detects metadata
corruption while locating data blocks and a superblock writeback occurs at
the same time:
task 1 task 2
------ ------
* A file operation *
nilfs_truncate()
nilfs_get_block()
down_read(rwsem A) <--
nilfs_bmap_lookup_contig()
... generic_shutdown_super()
nilfs_put_super()
* Prepare to write superblock *
down_write(rwsem B) <--
nilfs_cleanup_super()
* Detect b-tree corruption * nilfs_set_log_cursor()
nilfs_bmap_convert_error() nilfs_count_free_blocks()
__nilfs_error() down_read(rwsem A) <--
nilfs_set_error()
down_write(rwsem B) <--
*** DEADLOCK ***
Here, nilfs_get_block() readlocks rwsem A (= NILFS_MDT(dat_inode)->mi_sem)
and then calls nilfs_bmap_lookup_contig(), but if it fails due to metadata
corruption, __nilfs_error() is called from nilfs_bmap_convert_error()
inside the lock section.
Since __nilfs_error() calls nilfs_set_error() unless the filesystem is
read-only and nilfs_set_error() attempts to writelock rwsem B (=
nilfs->ns_sem) to write back superblock exclusively, hierarchical lock
acquisition occurs in the order rwsem A -> rwsem B.
Now, if another task starts updating the superblock, it may writelock
rwsem B during the lock sequence above, and can deadlock trying to
readlock rwsem A in nilfs_count_free_blocks().
However, there is actually no need to take rwsem A in
nilfs_count_free_blocks() because it, within the lock section, only reads
a single integer data on a shared struct with
nilfs_sufile_get_ncleansegs(). This has been the case after commit
aa474a2201 ("nilfs2: add local variable to cache the number of clean
segments"), that is, even before this bug was introduced.
So, this resolves the deadlock problem by just not taking the semaphore in
nilfs_count_free_blocks().
Link: https://lkml.kernel.org/r/20221029044912.9139-1-konishi.ryusuke@gmail.com
Fixes: e828949e5b ("nilfs2: call nilfs_error inside bmap routines")
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Reported-by: syzbot+45d6ce7b7ad7ef455d03@syzkaller.appspotmail.com
Tested-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Cc: <stable@vger.kernel.org> [2.6.38+
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea045fd344 upstream.
SAT SCSI/ATA Translation specification requires SCSI SYNCHRONIZE CACHE
(10) and (16) commands both shall be translated to ATA flush command.
Also, ZBC Zoned Block Commands specification mandates SYNCHRONIZE CACHE
(16) command support. However, libata translates only SYNCHRONIZE CACHE
(10). This results in SYNCHRONIZE CACHE (16) command failures on SATA
drives and then libata translation does not conform to ZBC. To avoid the
failure, add support for SYNCHRONIZE CACHE (16).
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Cc: stable@vger.kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 971cb608d1 upstream.
Although we tried to fix the regression for the recent changes with
the delayed card registration, it doesn't seem covering the all
cases; e.g. on Roland EDIROL M-100FX, where the generic quirk for
Roland devices is applied, it misses the card registration because the
detection of the last interface (apparently for MIDI) fails.
This patch is an attempt to recover from those failures by calling the
card register also at the error path for the secondary interfaces.
The card register condition is also extended to match with the old
check in the previous patch, too (i.e. the simple check of the
interface number) for catching the probe with errors.
Fixes: 39efc9c8a9 ("ALSA: usb-audio: Fix last interface check for registration")
Cc: <stable@vger.kernel.org>
Link: https://bugzilla.suse.com/show_bug.cgi?id=1205111
Link: https://lore.kernel.org/r/20221108065824.14418-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8360784494 upstream.
[[ NOTE: this is completely untested by the author, but included solely
because, as noted in commit df57d73276 ("mmc: sdhci-pci: Fix
SDHCI_RESET_ALL for CQHCI for Intel GLK-based controllers"), "other
drivers using CQHCI might benefit from a similar change, if they
also have CQHCI reset by SDHCI_RESET_ALL." We've now seen the same
bug on at least MSM, Arasan, and Intel hardware. ]]
SDHCI_RESET_ALL resets will reset the hardware CQE state, but we aren't
tracking that properly in software. When out of sync, we may trigger
various timeouts.
It's not typical to perform resets while CQE is enabled, but this may
occur in some suspend or error recovery scenarios.
Include this fix by way of the new sdhci_and_cqhci_reset() helper.
This patch depends on (and should not compile without) the patch
entitled "mmc: cqhci: Provide helper for resetting both SDHCI and
CQHCI".
Fixes: 3c4019f979 ("mmc: tegra: HW Command Queue Support for Tegra SDMMC")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221026124150.v4.5.I418c9eaaf754880fcd2698113e8c3ef821a944d7@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 162503fd1c upstream.
[[ NOTE: this is completely untested by the author, but included solely
because, as noted in commit df57d73276 ("mmc: sdhci-pci: Fix
SDHCI_RESET_ALL for CQHCI for Intel GLK-based controllers"), "other
drivers using CQHCI might benefit from a similar change, if they
also have CQHCI reset by SDHCI_RESET_ALL." We've now seen the same
bug on at least MSM, Arasan, and Intel hardware. ]]
SDHCI_RESET_ALL resets will reset the hardware CQE state, but we aren't
tracking that properly in software. When out of sync, we may trigger
various timeouts.
It's not typical to perform resets while CQE is enabled, but this may
occur in some suspend or error recovery scenarios.
Include this fix by way of the new sdhci_and_cqhci_reset() helper.
This patch depends on (and should not compile without) the patch
entitled "mmc: cqhci: Provide helper for resetting both SDHCI and
CQHCI".
Fixes: f545702b74 ("mmc: sdhci_am654: Add Support for Command Queuing Engine to J721E")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221026124150.v4.6.I35ca9d6220ba48304438b992a76647ca8e5b126f@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d249ac37f upstream.
SDHCI_RESET_ALL resets will reset the hardware CQE state, but we aren't
tracking that properly in software. When out of sync, we may trigger
various timeouts.
It's not typical to perform resets while CQE is enabled, but one
particular case I hit commonly enough: mmc_suspend() -> mmc_power_off().
Typically we will eventually deactivate CQE (cqhci_suspend() ->
cqhci_deactivate()), but that's not guaranteed -- in particular, if
we perform a partial (e.g., interrupted) system suspend.
The same bug was already found and fixed for two other drivers, in v5.7
and v5.9:
5cf583f1fb ("mmc: sdhci-msm: Deactivate CQE during SDHC reset")
df57d73276 ("mmc: sdhci-pci: Fix SDHCI_RESET_ALL for CQHCI for Intel
GLK-based controllers")
The latter is especially prescient, saying "other drivers using CQHCI
might benefit from a similar change, if they also have CQHCI reset by
SDHCI_RESET_ALL."
So like these other patches, deactivate CQHCI when resetting the
controller. Do this via the new sdhci_and_cqhci_reset() helper.
This patch depends on (and should not compile without) the patch
entitled "mmc: cqhci: Provide helper for resetting both SDHCI and
CQHCI".
Fixes: 84362d79f4 ("mmc: sdhci-of-arasan: Add CQHCI support for arasan,sdhci-5.1")
Cc: <stable@vger.kernel.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20221026124150.v4.2.I29f6a2189e84e35ad89c1833793dca9e36c64297@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ebb5fd38f4 upstream.
Several SDHCI drivers need to deactivate command queueing in their reset
hook (see sdhci_cqhci_reset() / sdhci-pci-core.c, for example), and
several more are coming.
Those reset implementations have some small subtleties (e.g., ordering
of initialization of SDHCI vs. CQHCI might leave us resetting with a
NULL ->cqe_private), and are often identical across different host
drivers.
We also don't want to force a dependency between SDHCI and CQHCI, or
vice versa; non-SDHCI drivers use CQHCI, and SDHCI drivers might support
command queueing through some other means.
So, implement a small helper, to avoid repeating the same mistakes in
different drivers. Simply stick it in a header, because it's so small it
doesn't deserve its own module right now, and inlining to each driver is
pretty reasonable.
This is marked for -stable, as it is an important prerequisite patch for
several SDHCI controller bugfixes that follow.
Cc: <stable@vger.kernel.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221026124150.v4.1.Ie85faa09432bfe1b0890d8c24ff95e17f3097317@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b9eaee982 upstream.
Currently, when mapping the EFI runtime regions in the EFI page tables,
we complain about misaligned regions in a rather noisy way, using
WARN().
Not only does this produce a lot of irrelevant clutter in the log, it is
factually incorrect, as misaligned runtime regions are actually allowed
by the EFI spec as long as they don't require conflicting memory types
within the same 64k page.
So let's drop the warning, and tweak the code so that we
- take both the start and end of the region into account when checking
for misalignment
- only revert to RWX mappings for non-code regions if misaligned code
regions are also known to exist.
Cc: <stable@vger.kernel.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 50e63dd8ed ]
Currently, RISC-V sets up reserved memory using the "early" copy of the
device tree. As a result, when trying to get a reserved memory region
using of_reserved_mem_lookup(), the pointer to reserved memory regions
is using the early, pre-virtual-memory address which causes a kernel
panic when trying to use the buffer's name:
Unable to handle kernel paging request at virtual address 00000000401c31ac
Oops [#1]
Modules linked in:
CPU: 0 PID: 0 Comm: swapper Not tainted 6.0.0-rc1-00001-g0d9d6953d834 #1
Hardware name: Microchip PolarFire-SoC Icicle Kit (DT)
epc : string+0x4a/0xea
ra : vsnprintf+0x1e4/0x336
epc : ffffffff80335ea0 ra : ffffffff80338936 sp : ffffffff81203be0
gp : ffffffff812e0a98 tp : ffffffff8120de40 t0 : 0000000000000000
t1 : ffffffff81203e28 t2 : 7265736572203a46 s0 : ffffffff81203c20
s1 : ffffffff81203e28 a0 : ffffffff81203d22 a1 : 0000000000000000
a2 : ffffffff81203d08 a3 : 0000000081203d21 a4 : ffffffffffffffff
a5 : 00000000401c31ac a6 : ffff0a00ffffff04 a7 : ffffffffffffffff
s2 : ffffffff81203d08 s3 : ffffffff81203d00 s4 : 0000000000000008
s5 : ffffffff000000ff s6 : 0000000000ffffff s7 : 00000000ffffff00
s8 : ffffffff80d9821a s9 : ffffffff81203d22 s10: 0000000000000002
s11: ffffffff80d9821c t3 : ffffffff812f3617 t4 : ffffffff812f3617
t5 : ffffffff812f3618 t6 : ffffffff81203d08
status: 0000000200000100 badaddr: 00000000401c31ac cause: 000000000000000d
[<ffffffff80338936>] vsnprintf+0x1e4/0x336
[<ffffffff80055ae2>] vprintk_store+0xf6/0x344
[<ffffffff80055d86>] vprintk_emit+0x56/0x192
[<ffffffff80055ed8>] vprintk_default+0x16/0x1e
[<ffffffff800563d2>] vprintk+0x72/0x80
[<ffffffff806813b2>] _printk+0x36/0x50
[<ffffffff8068af48>] print_reserved_mem+0x1c/0x24
[<ffffffff808057ec>] paging_init+0x528/0x5bc
[<ffffffff808031ae>] setup_arch+0xd0/0x592
[<ffffffff8080070e>] start_kernel+0x82/0x73c
early_init_fdt_scan_reserved_mem() takes no arguments as it operates on
initial_boot_params, which is populated by early_init_dt_verify(). On
RISC-V, early_init_dt_verify() is called twice. Once, directly, in
setup_arch() if CONFIG_BUILTIN_DTB is not enabled and once indirectly,
very early in the boot process, by parse_dtb() when it calls
early_init_dt_scan_nodes().
This first call uses dtb_early_va to set initial_boot_params, which is
not usable later in the boot process when
early_init_fdt_scan_reserved_mem() is called. On arm64 for example, the
corresponding call to early_init_dt_scan_nodes() uses fixmap addresses
and doesn't suffer the same fate.
Move early_init_fdt_scan_reserved_mem() further along the boot sequence,
after the direct call to early_init_dt_verify() in setup_arch() so that
the names use the correct virtual memory addresses. The above supposed
that CONFIG_BUILTIN_DTB was not set, but should work equally in the case
where it is - unflatted_and_copy_device_tree() also updates
initial_boot_params.
Reported-by: Valentina Fernandez <valentina.fernandezalanis@microchip.com>
Reported-by: Evgenii Shatokhin <e.shatokhin@yadro.com>
Link: https://lore.kernel.org/linux-riscv/f8e67f82-103d-156c-deb0-d6d6e2756f5e@microchip.com/
Fixes: 922b0375fc ("riscv: Fix memblock reservation for device tree blob")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Tested-by: Evgenii Shatokhin <e.shatokhin@yadro.com>
Link: https://lore.kernel.org/r/20221107151524.3941467-1-conor.dooley@microchip.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50f4dd657a ]
Even after commit 89fd4a1df8 ("riscv: jump_label: mark arguments as
const to satisfy asm constraints"), building with CC_OPTIMIZE_FOR_SIZE
+ LLVM=1 can reproduce below build error:
CC arch/riscv/kernel/vdso/vgettimeofday.o
In file included from <built-in>:4:
In file included from lib/vdso/gettimeofday.c:5:
In file included from include/vdso/datapage.h:17:
In file included from include/vdso/processor.h:10:
In file included from arch/riscv/include/asm/vdso/processor.h:7:
In file included from include/linux/jump_label.h:112:
arch/riscv/include/asm/jump_label.h:42:3: error:
invalid operand for inline asm constraint 'i'
" .option push \n\t"
^
1 error generated.
I think the problem is when "-Os" is passed as CFLAGS, it's removed by
"CFLAGS_REMOVE_vgettimeofday.o = $(CC_FLAGS_FTRACE) -Os" which is
introduced in commit e05d57dcb8 ("riscv: Fixup __vdso_gettimeofday
broke dynamic ftrace"), thus no optimization at all for vgettimeofday.c
arm64 does remove "-Os" as well, but it forces "-O2" after removing
"-Os".
I compared the generated vgettimeofday.o with "-O2" and "-Os",
I think no big performance difference. So let's tell the kbuild not
to remove "-Os" rather than follow arm64 style.
vdso related performance can be improved a lot when building kernel with
CC_OPTIMIZE_FOR_SIZE after this commit, ("-Os" VS no optimization)
Fixes: e05d57dcb8 ("riscv: Fixup __vdso_gettimeofday broke dynamic ftrace")
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20221031182943.2453-1-jszhang@kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23569b5652 ]
kmemleak reports memory leaks in macvlan_common_newlink, as follows:
ip link add link eth0 name .. type macvlan mode source macaddr add
<MAC-ADDR>
kmemleak reports:
unreferenced object 0xffff8880109bb140 (size 64):
comm "ip", pid 284, jiffies 4294986150 (age 430.108s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 b8 aa 5a 12 80 88 ff ff ..........Z.....
80 1b fa 0d 80 88 ff ff 1e ff ac af c7 c1 6b 6b ..............kk
backtrace:
[<ffffffff813e06a7>] kmem_cache_alloc_trace+0x1c7/0x300
[<ffffffff81b66025>] macvlan_hash_add_source+0x45/0xc0
[<ffffffff81b66a67>] macvlan_changelink_sources+0xd7/0x170
[<ffffffff81b6775c>] macvlan_common_newlink+0x38c/0x5a0
[<ffffffff81b6797e>] macvlan_newlink+0xe/0x20
[<ffffffff81d97f8f>] __rtnl_newlink+0x7af/0xa50
[<ffffffff81d98278>] rtnl_newlink+0x48/0x70
...
In the scenario where the macvlan mode is configured as 'source',
macvlan_changelink_sources() will be execured to reconfigure list of
remote source mac addresses, at the same time, if register_netdevice()
return an error, the resource generated by macvlan_changelink_sources()
is not cleaned up.
Using this patch, in the case of an error, it will execute
macvlan_flush_sources() to ensure that the resource is cleaned up.
Fixes: aa5fd0fb77 ("driver: macvlan: Destroy new macvlan port if macvlan_common_newlink failed.")
Signed-off-by: Chuang Wang <nashuiliang@gmail.com>
Link: https://lore.kernel.org/r/20221109090735.690500-1-nashuiliang@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 879785def0 ]
Commit aaab73f8fb ("macsec: clear encryption keys from the stack after
setting up offload") made sure to clean encryption keys from the stack
after setting up offloading, but the atlantic driver made a copy and did
not clear it. Fix this.
[4 Fixes tags below, all part of the same series, no need to split this]
Fixes: 9ff40a751a ("net: atlantic: MACSec ingress offload implementation")
Fixes: b8f8a0b7b5 ("net: atlantic: MACSec ingress offload HW bindings")
Fixes: 27736563ce ("net: atlantic: MACSec egress offload implementation")
Fixes: 9d106c6dd8 ("net: atlantic: MACSec egress offload HW bindings")
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b16b3fdf6 ]
Commit aaab73f8fb ("macsec: clear encryption keys from the stack after
setting up offload") made sure to clean encryption keys from the stack
after setting up offloading, but the MSCC PHY driver made a copy, kept
it in the flow data and did not clear it when freeing a flow. Fix this.
Fixes: 28c5107aa9 ("net: phy: mscc: macsec support")
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f94d0498f ]
The node returned by of_get_child_by_name() with refcount decremented,
of_node_put() needs be called when finish using it. So add it in the
error path in loongson_dwmac_probe() and in loongson_dwmac_remove().
Fixes: 2ae34111fe ("stmmac: dwmac-loongson: fix invalid mdio_node")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe5b3ce8b4 ]
Add missing pci_disable_device() in the error path in loongson_dwmac_probe().
Fixes: 30bba69d7d ("stmmac: pci: Add dwmac support for Loongson")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2d45fdf9a ]
pci_enable_msi() has been called in loongson_dwmac_probe(),
so pci_disable_msi() needs be called in remove path and error
path of probe().
Fixes: 30bba69d7d ("stmmac: pci: Add dwmac support for Loongson")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f4f4096b41 ]
The pkt_reformat pointer being saved under flow_act and not
dest attribute in the termination table instance.
Fix the comparison pointers.
Also fix returning success if one pkt_reformat pointer is null
and the other is not.
Fixes: 249ccc3c95 ("net/mlx5e: Add support for offloading traffic from uplink to uplink")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Chris Mi <cmi@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2808b37b59 ]
For a single CPU system, the kernel thread executing mlx5_cmd_flush()
never releases the CPU but calls down_trylock(&cmd→sem) in a busy loop.
On a single processor system, this leads to a deadlock as the kernel
thread which executes mlx5_cmd_invoke() never gets scheduled. Fix this,
by adding the cond_resched() call to the loop, allow the command
completion kernel thread to execute.
Fixes: 8e715cd613 ("net/mlx5: Set command entry semaphore up once got index free")
Signed-off-by: Alexander Schmidt <alexschm@de.ibm.com>
Signed-off-by: Roy Novich <royno@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15f8f16895 ]
Mlx5 LAG is initialized asynchronously on a workqueue which means that for
a brief moment after setting mlx5 UL representors as lower devices of a
bond netdevice the LAG itself is not fully initialized in the driver. When
adding such bond device to a bridge mlx5 bridge code will not consider it
as offload-capable, skip creating necessary bookkeeping and fail any
further bridge offload-related commands with it (setting VLANs, offloading
FDBs, etc.). In order to make the error explicit during bridge
initialization stage implement the code that detects such condition during
NETDEV_PRECHANGEUPPER event and returns an error.
Fixes: ff9b752146 ("net/mlx5: Bridge, support LAG")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d38a648d2d ]
ipc_pcie_read_bios_cfg() is using the acpi_evaluate_dsm() to
obtain the wwan power state configuration from BIOS but is
not freeing the acpi_object. The acpi_evaluate_dsm() returned
acpi_object to be freed.
Free the acpi_object after use.
Fixes: 7e98d785ae ("net: iosm: entry point")
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03c1f1ef15 ]
syzbot reported a warning like below [1]:
WARNING: CPU: 3 PID: 9 at net/netfilter/nf_tables_api.c:10096 nf_tables_exit_net+0x71c/0x840
Modules linked in:
CPU: 2 PID: 9 Comm: kworker/u8:0 Tainted: G W 6.1.0-rc3-00072-g8e5423e991e8 #47
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.0-1.fc36 04/01/2014
Workqueue: netns cleanup_net
RIP: 0010:nf_tables_exit_net+0x71c/0x840
...
Call Trace:
<TASK>
? __nft_release_table+0xfc0/0xfc0
ops_exit_list+0xb5/0x180
cleanup_net+0x506/0xb10
? unregister_pernet_device+0x80/0x80
process_one_work+0xa38/0x1730
? pwq_dec_nr_in_flight+0x2b0/0x2b0
? rwlock_bug.part.0+0x90/0x90
? _raw_spin_lock_irq+0x46/0x50
worker_thread+0x67e/0x10e0
? process_one_work+0x1730/0x1730
kthread+0x2e5/0x3a0
? kthread_complete_and_exit+0x40/0x40
ret_from_fork+0x1f/0x30
</TASK>
In nf_tables_exit_net(), there is a case where nft_net->commit_list is
empty but nft_net->module_list is not empty. Such a case occurs with
the following scenario:
1. nfnetlink_rcv_batch() is called
2. nf_tables_newset() returns -EAGAIN and NFNL_BATCH_FAILURE bit is
set to status
3. nf_tables_abort() is called with NFNL_ABORT_AUTOLOAD
(nft_net->commit_list is released, but nft_net->module_list is not
because of NFNL_ABORT_AUTOLOAD flag)
4. Jump to replay label
5. netlink_skb_clone() fails and returns from the function (this is
caused by fault injection in the reproducer of syzbot)
This patch fixes this issue by calling __nf_tables_abort() when
nft_net->module_list is not empty in nf_tables_exit_net().
Fixes: eb014de4fd ("netfilter: nf_tables: autoload modules from the abort path")
Link: https://syzkaller.appspot.com/bug?id=802aba2422de4218ad0c01b46c9525cc9d4e4aa3 [1]
Reported-by: syzbot+178efee9e2d7f87f5103@syzkaller.appspotmail.com
Signed-off-by: Shigeru Yoshida <syoshida@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03832a32bf ]
When type is NFNL_CB_MUTEX and -EAGAIN error occur in nfnetlink_rcv_msg(),
it does not execute nfnl_unlock(). That would trigger potential dead lock.
Fixes: 50f2db9e36 ("netfilter: nfnetlink: consolidate callback types")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 94d957ae51 ]
Commit 3af1dfdd51 ("perf build: Move perf_dlfilters.h in the
source tree") moved perf_dlfilters.h to the include/perf/ directory
while include/perf is ignored because it has 'perf' in the name. Newly
created files in the include/perf/ directory will be ignored.
Testing:
Before:
$ touch tools/perf/include/perf/junk
$ git status | grep junk
$ git check-ignore -v tools/perf/include/perf/junk
tools/perf/.gitignore:6:perf tools/perf/include/perf/junk
After:
$ git status | grep junk
tools/perf/include/perf/junk
$ git check-ignore -v tools/perf/include/perf/junk
Add !include/perf/ to perf's .gitignore file.
Fixes: 3af1dfdd51 ("perf build: Move perf_dlfilters.h in the source tree")
Signed-off-by: Donglin Peng <dolinux.peng@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20221103092704.173391-1-dolinux.peng@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad353b710c ]
'perf stat' with CSV output option prints an extra empty string as first
field in metrics output line. Sample output below:
# ./perf stat -x, --per-socket -a -C 1 ls
S0,1,1.78,msec,cpu-clock,1785146,100.00,0.973,CPUs utilized
S0,1,26,,context-switches,1781750,100.00,0.015,M/sec
S0,1,1,,cpu-migrations,1780526,100.00,0.561,K/sec
S0,1,1,,page-faults,1779060,100.00,0.561,K/sec
S0,1,875807,,cycles,1769826,100.00,0.491,GHz
S0,1,85281,,stalled-cycles-frontend,1767512,100.00,9.74,frontend cycles idle
S0,1,576839,,stalled-cycles-backend,1766260,100.00,65.86,backend cycles idle
S0,1,288430,,instructions,1762246,100.00,0.33,insn per cycle
====> ,S0,1,,,,,,,2.00,stalled cycles per insn
The above command line uses field separator as "," via "-x," option and
per-socket option displays socket value as first field. But here the
last line for "stalled cycles per insn" has "," in the beginning.
Sample output using interval mode:
# ./perf stat -I 1000 -x, --per-socket -a -C 1 ls
0.001813453,S0,1,1.87,msec,cpu-clock,1872052,100.00,0.002,CPUs utilized
0.001813453,S0,1,2,,context-switches,1868028,100.00,1.070,K/sec
------
0.001813453,S0,1,85379,,instructions,1856754,100.00,0.32,insn per cycle
====> 0.001813453,,S0,1,,,,,,,1.34,stalled cycles per insn
Above result also has an extra CSV separator after
the timestamp. Patch addresses extra field separator
in the beginning of the metric output line.
The counter stats are displayed by function
"perf_stat__print_shadow_stats" in code
"util/stat-shadow.c". While printing the stats info
for "stalled cycles per insn", function "new_line_csv"
is used as new_line callback.
The new_line_csv function has check for "os->prefix"
and if prefix is not null, it will be printed along
with cvs separator.
Snippet from "new_line_csv":
if (os->prefix)
fprintf(os->fh, "%s%s", os->prefix, config->csv_sep);
Here os->prefix gets printed followed by ","
which is the cvs separator. The os->prefix is
used in interval mode option ( -I ), to print
time stamp on every new line. But prefix is
already set to contain CSV separator when used
in interval mode for CSV option.
Reference: Function "static void print_interval"
Snippet:
sprintf(prefix, "%6lu.%09lu%s", ts->tv_sec, ts->tv_nsec, config->csv_sep);
Also if prefix is not assigned (if not used with
-I option), it gets set to empty string.
Reference: function printout() in util/stat-display.c
Snippet:
.prefix = prefix ? prefix : "",
Since prefix already set to contain cvs_sep in interval
option, patch removes printing config->csv_sep in
new_line_csv function to avoid printing extra field.
After the patch:
# ./perf stat -x, --per-socket -a -C 1 ls
S0,1,2.04,msec,cpu-clock,2045202,100.00,1.013,CPUs utilized
S0,1,2,,context-switches,2041444,100.00,979.289,/sec
S0,1,0,,cpu-migrations,2040820,100.00,0.000,/sec
S0,1,2,,page-faults,2040288,100.00,979.289,/sec
S0,1,254589,,cycles,2036066,100.00,0.125,GHz
S0,1,82481,,stalled-cycles-frontend,2032420,100.00,32.40,frontend cycles idle
S0,1,113170,,stalled-cycles-backend,2031722,100.00,44.45,backend cycles idle
S0,1,88766,,instructions,2030942,100.00,0.35,insn per cycle
S0,1,,,,,,,1.27,stalled cycles per insn
Fixes: 92a61f6412 ("perf stat: Implement CSV metrics output")
Reported-by: Disha Goel <disgoel@linux.vnet.ibm.com>
Reviewed-By: Kajol Jain <kjain@linux.ibm.com>
Signed-off-by: Athira Jajeev <atrajeev@linux.vnet.ibm.com>
Tested-by: Disha Goel <disgoel@linux.vnet.ibm.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: James Clark <james.clark@arm.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nageswara R Sastry <rnsastry@linux.ibm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: https://lore.kernel.org/r/20221018085605.63834-1-atrajeev@linux.vnet.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3faf7e14ec ]
If lapb_register() failed when lapb device goes to up for the first time,
the NAPI is not disabled. As a result, the invalid opcode issue is
reported when the lapb device goes to up for the second time.
The stack info is as follows:
[ 1958.311422][T11356] kernel BUG at net/core/dev.c:6442!
[ 1958.312206][T11356] invalid opcode: 0000 [#1] PREEMPT SMP KASAN
[ 1958.315979][T11356] RIP: 0010:napi_enable+0x16a/0x1f0
[ 1958.332310][T11356] Call Trace:
[ 1958.332817][T11356] <TASK>
[ 1958.336135][T11356] lapbeth_open+0x18/0x90
[ 1958.337446][T11356] __dev_open+0x258/0x490
[ 1958.341672][T11356] __dev_change_flags+0x4d4/0x6a0
[ 1958.345325][T11356] dev_change_flags+0x93/0x160
[ 1958.346027][T11356] devinet_ioctl+0x1276/0x1bf0
[ 1958.346738][T11356] inet_ioctl+0x1c8/0x2d0
[ 1958.349638][T11356] sock_ioctl+0x5d1/0x750
[ 1958.356059][T11356] __x64_sys_ioctl+0x3ec/0x1790
[ 1958.365594][T11356] do_syscall_64+0x35/0x80
[ 1958.366239][T11356] entry_SYSCALL_64_after_hwframe+0x46/0xb0
[ 1958.377381][T11356] </TASK>
Fixes: 514e1150da ("net: x25: Queue received packets in the drivers instead of per-CPU queues")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Link: https://lore.kernel.org/r/20221107011445.207372-1-shaozhengchao@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3d726cb84 ]
The first IRQ is required, but IRQs 1 through (nb_phy_chans - 1) are
optional, because on some platforms (e.g. PXA168) there is a single IRQ
shared between all channels.
This change inhibits a flood of "IRQ index # not found" messages at
startup. Tested on a PXA168-based device.
Fixes: 7723f4c5ec ("driver core: platform: Add an error message to platform_get_irq*()")
Signed-off-by: Doug Brown <doug@schmorgal.com>
Link: https://lore.kernel.org/r/20220906000709.52705-1-doug@schmorgal.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c075b192f ]
This is a follow-up for commit 974cb0e3e7 ("tipc: fix uninit-value
in tipc_nl_compat_name_table_dump") where it should have type casted
sizeof(..) to int to work when TLV_GET_DATA_LEN() returns a negative
value.
syzbot reported a call trace because of it:
BUG: KMSAN: uninit-value in ...
tipc_nl_compat_name_table_dump+0x841/0xea0 net/tipc/netlink_compat.c:934
__tipc_nl_compat_dumpit+0xab2/0x1320 net/tipc/netlink_compat.c:238
tipc_nl_compat_dumpit+0x991/0xb50 net/tipc/netlink_compat.c:321
tipc_nl_compat_recv+0xb6e/0x1640 net/tipc/netlink_compat.c:1324
genl_family_rcv_msg_doit net/netlink/genetlink.c:731 [inline]
genl_family_rcv_msg net/netlink/genetlink.c:775 [inline]
genl_rcv_msg+0x103f/0x1260 net/netlink/genetlink.c:792
netlink_rcv_skb+0x3a5/0x6c0 net/netlink/af_netlink.c:2501
genl_rcv+0x3c/0x50 net/netlink/genetlink.c:803
netlink_unicast_kernel net/netlink/af_netlink.c:1319 [inline]
netlink_unicast+0xf3b/0x1270 net/netlink/af_netlink.c:1345
netlink_sendmsg+0x1288/0x1440 net/netlink/af_netlink.c:1921
sock_sendmsg_nosec net/socket.c:714 [inline]
sock_sendmsg net/socket.c:734 [inline]
Reported-by: syzbot+e5dbaaa238680ce206ea@syzkaller.appspotmail.com
Fixes: 974cb0e3e7 ("tipc: fix uninit-value in tipc_nl_compat_name_table_dump")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Link: https://lore.kernel.org/r/ccd6a7ea801b15aec092c3b532a883b4c5708695.1667594933.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed4314f772 ]
There are two problems with meson8b_devm_clk_prepare_enable(),
introduced in commit a54dc4a490 ("net: stmmac: dwmac-meson8b:
Make the clock enabling code re-usable"):
- It doesn't pass the clk argument, but instead always the
rgmii_tx_clk of the device.
- It silently ignores the return value of devm_add_action_or_reset().
The former didn't become an actual bug until another user showed up in
the next commit 9308c47640 ("net: stmmac: dwmac-meson8b: add support
for the RX delay configuration"). The latter means the callers could
end up with the clock not actually prepared/enabled.
Fixes: a54dc4a490 ("net: stmmac: dwmac-meson8b: Make the clock enabling code re-usable")
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20221104083004.2212520-1-linux@rasmusvillemoes.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8aa59e3559 ]
It causes NULL pointer dereference when testing as following:
(a) use syscall(__NR_socket, 0x10ul, 3ul, 0) to create netlink socket.
(b) use syscall(__NR_sendmsg, ...) to create bond link device and vxcan
link device, and bind vxcan device to bond device (can also use
ifenslave command to bind vxcan device to bond device).
(c) use syscall(__NR_socket, 0x1dul, 3ul, 1) to create CAN socket.
(d) use syscall(__NR_bind, ...) to bind the bond device to CAN socket.
The bond device invokes the can-raw protocol registration interface to
receive CAN packets. However, ml_priv is not allocated to the dev,
dev_rcv_lists is assigned to NULL in can_rx_register(). In this case,
it will occur the NULL pointer dereference issue.
The following is the stack information:
BUG: kernel NULL pointer dereference, address: 0000000000000008
PGD 122a4067 P4D 122a4067 PUD 1223c067 PMD 0
Oops: 0000 [#1] PREEMPT SMP
RIP: 0010:can_rx_register+0x12d/0x1e0
Call Trace:
<TASK>
raw_enable_filters+0x8d/0x120
raw_enable_allfilters+0x3b/0x130
raw_bind+0x118/0x4f0
__sys_bind+0x163/0x1a0
__x64_sys_bind+0x1e/0x30
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
</TASK>
Fixes: 4e096a1886 ("net: introduce CAN specific pointer in the struct net_device")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Reviewed-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/all/20221028085650.170470-1-shaozhengchao@huawei.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c175da7b0 ]
If setsockopt with option name of TCP_REPAIR_OPTIONS and opt_code
of TCPOPT_SACK_PERM is called to enable sack after data is sent
and dupacks are received , it will trigger a warning in function
tcp_verify_left_out() as follows:
============================================
WARNING: CPU: 8 PID: 0 at net/ipv4/tcp_input.c:2132
tcp_timeout_mark_lost+0x154/0x160
tcp_enter_loss+0x2b/0x290
tcp_retransmit_timer+0x50b/0x640
tcp_write_timer_handler+0x1c8/0x340
tcp_write_timer+0xe5/0x140
call_timer_fn+0x3a/0x1b0
__run_timers.part.0+0x1bf/0x2d0
run_timer_softirq+0x43/0xb0
__do_softirq+0xfd/0x373
__irq_exit_rcu+0xf6/0x140
The warning is caused in the following steps:
1. a socket named socketA is created
2. socketA enters repair mode without build a connection
3. socketA calls connect() and its state is changed to TCP_ESTABLISHED
directly
4. socketA leaves repair mode
5. socketA calls sendmsg() to send data, packets_out and sack_outs(dup
ack receives) increase
6. socketA enters repair mode again
7. socketA calls setsockopt with TCPOPT_SACK_PERM to enable sack
8. retransmit timer expires, it calls tcp_timeout_mark_lost(), lost_out
increases
9. sack_outs + lost_out > packets_out triggers since lost_out and
sack_outs increase repeatly
In function tcp_timeout_mark_lost(), tp->sacked_out will be cleared if
Step7 not happen and the warning will not be triggered. As suggested by
Denis and Eric, TCP_REPAIR_OPTIONS should be prohibited if data was
already sent.
socket-tcp tests in CRIU has been tested as follows:
$ sudo ./test/zdtm.py run -t zdtm/static/socket-tcp* --keep-going \
--ignore-taint
socket-tcp* represent all socket-tcp tests in test/zdtm/static/.
Fixes: b139ba4e90 ("tcp: Repair connection-time negotiated parameters")
Signed-off-by: Lu Wei <luwei32@huawei.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf53db768a ]
A problem about modprobe vc4 failed is triggered with the following log
given:
[ 420.327987] Error: Driver 'vc4_hvs' is already registered, aborting...
[ 420.333904] failed to register platform driver vc4_hvs_driver [vc4]: -16
modprobe: ERROR: could not insert 'vc4': Device or resource busy
The reason is that vc4_drm_register() returns platform_driver_register()
directly without checking its return value, if platform_driver_register()
fails, it returns without unregistering all the vc4 drivers, resulting the
vc4 can never be installed later.
A simple call graph is shown as below:
vc4_drm_register()
platform_register_drivers() # all vc4 drivers are registered
platform_driver_register()
driver_register()
bus_add_driver()
priv = kzalloc(...) # OOM happened
# return without unregister drivers
Fixing this problem by checking the return value of
platform_driver_register() and do platform_unregister_drivers() if
error happened.
Fixes: c8b75bca92 ("drm/vc4: Add KMS support for Raspberry Pi.")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20221103014705.109322-1-yuancan@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 668205b9c9 ]
MHI driver registers network device without setting the
needs_free_netdev flag, and does NOT call free_netdev() when
unregisters network device, which causes a memory leak.
This patch sets needs_free_netdev to true when registers
network device, which makes netdev subsystem call free_netdev()
automatically after unregister_netdevice().
Fixes: aa730a9905 ("net: wwan: Add MHI MBIM network driver")
Signed-off-by: HW He <hw.he@mediatek.com>
Signed-off-by: Zhaoping Shu <zhaoping.shu@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f25caaca42 ]
IOSM driver registers network device without setting the
needs_free_netdev flag, and does NOT call free_netdev() when
unregisters network device, which causes a memory leak.
This patch sets needs_free_netdev to true when registers
network device, which makes netdev subsystem call free_netdev()
automatically after unregister_netdevice().
Fixes: 2a54f2c779 ("net: iosm: net driver")
Signed-off-by: HW He <hw.he@mediatek.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Zhaoping Shu <zhaoping.shu@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 85cbaf032d ]
When following tests are performed, it will cause dev reference counting
leakage.
a)ip link add bond2 type bond mode balance-rr
b)ip link set bond2 up
c)ifenslave -f bond2 rose1
d)ip link del bond2
When new bond device is created, the default type of the bond device is
ether. And the bond device is up, bpq_device_event() receives the message
and creates a new bpq device. In this case, the reference count value of
dev is hold once. But after "ifenslave -f bond2 rose1" command is
executed, the type of the bond device is changed to rose. When the bond
device is unregistered, bpq_device_event() will not put the dev reference
count.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 531705a765 ]
When following tests are performed, it will cause dev reference counting
leakage.
a)ip link add bond2 type bond mode balance-rr
b)ip link set bond2 up
c)ifenslave -f bond2 rose1
d)ip link del bond2
When new bond device is created, the default type of the bond device is
ether. And the bond device is up, lapbeth_device_event() receives the
message and creates a new lapbeth device. In this case, the reference
count value of dev is hold once. But after "ifenslave -f bond2 rose1"
command is executed, the type of the bond device is changed to rose. When
the bond device is unregistered, lapbeth_device_event() will not put the
dev reference count.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6973091d1b ]
When running under PV, the guest's TOD clock is under control of the
ultravisor and the hypervisor isn't allowed to change it. Hence, don't
allow userspace to change the guest's TOD clock by returning
-EOPNOTSUPP.
When userspace changes the guest's TOD clock, KVM updates its
kvm.arch.epoch field and, in addition, the epoch field in all state
descriptions of all VCPUs.
But, under PV, the ultravisor will ignore the epoch field in the state
description and simply overwrite it on next SIE exit with the actual
guest epoch. This leads to KVM having an incorrect view of the guest's
TOD clock: it has updated its internal kvm.arch.epoch field, but the
ultravisor ignores the field in the state description.
Whenever a guest is now waiting for a clock comparator, KVM will
incorrectly calculate the time when the guest should wake up, possibly
causing the guest to sleep for much longer than expected.
With this change, kvm_s390_set_tod() will now take the kvm->lock to be
able to call kvm_s390_pv_is_protected(). Since kvm_s390_set_tod_clock()
also takes kvm->lock, use __kvm_s390_set_tod_clock() instead.
The function kvm_s390_set_tod_clock is now unused, hence remove it.
Update the documentation to indicate the TOD clock attr calls can now
return -EOPNOTSUPP.
Fixes: 0f30350471 ("KVM: s390: protvirt: Do only reset registers that are accessible")
Reported-by: Marc Hartmayer <mhartmay@linux.ibm.com>
Signed-off-by: Nico Boehr <nrb@linux.ibm.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Link: https://lore.kernel.org/r/20221011160712.928239-2-nrb@linux.ibm.com
Message-Id: <20221011160712.928239-2-nrb@linux.ibm.com>
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46653972e3 ]
Shifting signed 32-bit value by 31 bits is undefined, so changing
significant bit to unsigned. The UBSAN warning calltrace like below:
UBSAN: shift-out-of-bounds in security/commoncap.c:1252:2
left shift of 1 by 31 places cannot be represented in type 'int'
Call Trace:
<TASK>
dump_stack_lvl+0x7d/0xa5
dump_stack+0x15/0x1b
ubsan_epilogue+0xe/0x4e
__ubsan_handle_shift_out_of_bounds+0x1e7/0x20c
cap_task_prctl+0x561/0x6f0
security_task_prctl+0x5a/0xb0
__x64_sys_prctl+0x61/0x8f0
do_syscall_64+0x58/0x80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
</TASK>
Fixes: e338d263a7 ("Add 64-bit capability support to the kernel")
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Acked-by: Andrew G. Morgan <morgan@kernel.org>
Reviewed-by: Serge Hallyn <serge@hallyn.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b7cbc6740b ]
When the mac device gets removed, it leaves behind the ethernet device.
This will result in a segfault next time the ethernet device accesses
mac_dev. Remove the ethernet device when we get removed to prevent
this. This is not completely reversible, since some resources aren't
cleaned up properly, but that can be addressed later.
Fixes: 3933961682 ("fsl/fman: Add FMan MAC driver")
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20221103182831.2248833-1-sean.anderson@seco.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 02597d3914 ]
In the bnxt_en driver ndo_rx_flow_steer returns '0' whenever an entry
that we are attempting to steer is already found. This is not the
correct behavior. The return code should be the value/index that
corresponds to the entry. Returning zero all the time causes the
RFS records to be incorrect unless entry '0' is the correct one. As
flows migrate to different cores this can create entries that are not
correct.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Reported-by: Akshay Navgire <anavgire@purestorage.com>
Signed-off-by: Alex Barba <alex.barba@broadcom.com>
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51afe9026d ]
In scenarios where multiple errors have occurred
for a SQ before SW starts handling error interrupt,
SQ_CTX[OP_INT] may get overwritten leading to
NIX_LF_SQ_OP_INT returning incorrect value.
To workaround this read LMT, MNQ and SQ individual
error status registers to determine the cause of error.
Fixes: 4ff7d1488a ("octeontx2-pf: Error handling support")
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Reviewed-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit af3826db74 ]
Current driver uses software CQ head pointer to poll on CQE
header in memory to determine if CQE is valid. Software needs
to make sure, that the reads of the CQE do not get re-ordered
so much that it ends up with an inconsistent view of the CQE.
To ensure that DMB barrier after read to first CQE cacheline
and before reading of the rest of the CQE is needed.
But having barrier for every CQE read will impact the performance,
instead use hardware CQ head and tail pointers to find the
valid number of CQEs.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 51afe9026d ("octeontx2-pf: NIX TX overwrites SQ_CTX_HW_S[SQ_INT]")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aaab73f8fb ]
macsec_add_rxsa and macsec_add_txsa copy the key to an on-stack
offloading context to pass it to the drivers, but leaves it there when
it's done. Clear it with memzero_explicit as soon as it's not needed
anymore.
Fixes: 3cf3227a21 ("net: macsec: hardware offloading infrastructure")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 80df470635 ]
macsec_is_configured incorrectly uses secy->n_rx_sc to check if some
RXSCs exist. secy->n_rx_sc only counts the number of active RXSCs, but
there can also be inactive SCs as well, which may be stored in the
driver (in case we're disabling offloading), or would have to be
pushed to the device (in case we're trying to enable offloading).
As long as RXSCs active on creation and never turned off, the issue is
not visible.
Fixes: dcb780fb27 ("net: macsec: add nla support for changing the offloading selection")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 73a4b31c9d ]
secy->n_rx_sc is supposed to be the number of _active_ rxsc's within a
secy. This is then used by macsec_send_sci to help decide if we should
add the SCI to the header or not.
This logic is currently broken when we create a new RXSC and turn it
off at creation, as create_rx_sc always sets ->active to true (and
immediately uses that to increment n_rx_sc), and only later
macsec_add_rxsc sets rx_sc->active.
Fixes: c09440f7dc ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 93a3094782 ]
Currently we get an inconsistent state:
- netlink returns the error to userspace
- the RXSC is installed but not offloaded
Then the device could get confused when we try to add an RXSA, because
the RXSC isn't supposed to exist.
Fixes: 3cf3227a21 ("net: macsec: hardware offloading infrastructure")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e4b7a99a0 ]
Since commit 3dcbdb134f ("net: gso: Fix skb_segment splat when
splitting gso_size mangled skb having linear-headed frag_list"), it is
allowed to change gso_size of a GRO packet. However, that commit assumes
that "checking the first list_skb member suffices; i.e if either of the
list_skb members have non head_frag head, then the first one has too".
It turns out this assumption does not hold. We've seen BUG_ON being hit
in skb_segment when skbs on the frag_list had differing head_frag with
the vmxnet3 driver. This happens because __netdev_alloc_skb and
__napi_alloc_skb can return a skb that is page backed or kmalloced
depending on the requested size. As the result, the last small skb in
the GRO packet can be kmalloced.
There are three different locations where this can be fixed:
(1) We could check head_frag in GRO and not allow GROing skbs with
different head_frag. However, that would lead to performance
regression on normal forward paths with unmodified gso_size, where
!head_frag in the last packet is not a problem.
(2) Set a flag in bpf_skb_net_grow and bpf_skb_net_shrink indicating
that NETIF_F_SG is undesirable. That would need to eat a bit in
sk_buff. Furthermore, that flag can be unset when all skbs on the
frag_list are page backed. To retain good performance,
bpf_skb_net_grow/shrink would have to walk the frag_list.
(3) Walk the frag_list in skb_segment when determining whether
NETIF_F_SG should be cleared. This of course slows things down.
This patch implements (3). To limit the performance impact in
skb_segment, the list is walked only for skbs with SKB_GSO_DODGY set
that have gso_size changed. Normal paths thus will not hit it.
We could check only the last skb but since we need to walk the whole
list anyway, let's stay on the safe side.
Fixes: 3dcbdb134f ("net: gso: Fix skb_segment splat when splitting gso_size mangled skb having linear-headed frag_list")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/e04426a6a91baf4d1081e1b478c82b5de25fdf21.1667407944.git.jbenc@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f1db20814a ]
Some helper functions will allocate memory. To avoid memory leaks, the
verifier requires the eBPF program to release these memories by calling
the corresponding helper functions.
When a resource is released, all pointer registers corresponding to the
resource should be invalidated. The verifier use release_references() to
do this job, by apply __mark_reg_unknown() to each relevant register.
It will give these registers the type of SCALAR_VALUE. A register that
will contain a pointer value at runtime, but of type SCALAR_VALUE, which
may allow the unprivileged user to get a kernel pointer by storing this
register into a map.
Using __mark_reg_not_init() while NOT allow_ptr_leaks can mitigate this
problem.
Fixes: fd978bf7fd ("bpf: Add reference tracking to verifier")
Signed-off-by: Youlin Li <liulin063@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20221103093440.3161-1-liulin063@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b239da3420 ]
For a lot of use cases in future patches, we will want to modify the
state of registers part of some same 'group' (e.g. same ref_obj_id). It
won't just be limited to releasing reference state, but setting a type
flag dynamically based on certain actions, etc.
Hence, we need a way to easily pass a callback to the function that
iterates over all registers in current bpf_verifier_state in all frames
upto (and including) the curframe.
While in C++ we would be able to easily use a lambda to pass state and
the callback together, sadly we aren't using C++ in the kernel. The next
best thing to avoid defining a function for each case seems like
statement expressions in GNU C. The kernel already uses them heavily,
hence they can passed to the macro in the style of a lambda. The
statement expression will then be substituted in the for loop bodies.
Variables __state and __reg are set to current bpf_func_state and reg
for each invocation of the expression inside the passed in verifier
state.
Then, convert mark_ptr_or_null_regs, clear_all_pkt_pointers,
release_reference, find_good_pkt_pointers, find_equal_scalars to
use bpf_for_each_reg_in_vstate.
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Link: https://lore.kernel.org/r/20220904204145.3089-16-memxor@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Stable-dep-of: f1db20814a ("bpf: Fix wrong reg type conversion in release_reference()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8bbabb3fdd ]
Stanislav reported a lockdep warning, which is caused by the
cancel_work_sync() called inside sock_map_close(), as analyzed
below by Jakub:
psock->work.func = sk_psock_backlog()
ACQUIRE psock->work_mutex
sk_psock_handle_skb()
skb_send_sock()
__skb_send_sock()
sendpage_unlocked()
kernel_sendpage()
sock->ops->sendpage = inet_sendpage()
sk->sk_prot->sendpage = tcp_sendpage()
ACQUIRE sk->sk_lock
tcp_sendpage_locked()
RELEASE sk->sk_lock
RELEASE psock->work_mutex
sock_map_close()
ACQUIRE sk->sk_lock
sk_psock_stop()
sk_psock_clear_state(psock, SK_PSOCK_TX_ENABLED)
cancel_work_sync()
__cancel_work_timer()
__flush_work()
// wait for psock->work to finish
RELEASE sk->sk_lock
We can move the cancel_work_sync() out of the sock lock protection,
but still before saved_close() was called.
Fixes: 799aa7f98d ("skmsg: Avoid lock_sock() in sk_psock_backlog()")
Reported-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Jakub Sitnicki <jakub@cloudflare.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/bpf/20221102043417.279409-1-xiyou.wangcong@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 697fb80a53 ]
syzbot reproduced the bug ...
BUG: sleeping function called from invalid context at kernel/workqueue.c:3010
... with the following stack trace fragment ...
start_flush_work kernel/workqueue.c:3010 [inline]
__flush_work+0x109/0xb10 kernel/workqueue.c:3074
__cancel_work_timer+0x3f9/0x570 kernel/workqueue.c:3162
sk_psock_stop+0x4cb/0x630 net/core/skmsg.c:802
sock_map_destroy+0x333/0x760 net/core/sock_map.c:1581
inet_csk_destroy_sock+0x196/0x440 net/ipv4/inet_connection_sock.c:1130
__tcp_close+0xd5b/0x12b0 net/ipv4/tcp.c:2897
tcp_close+0x29/0xc0 net/ipv4/tcp.c:2909
... introduced by d8616ee2af. Do a quick trace of the code path and the
bug is obvious:
inet_csk_destroy_sock(sk)
sk_prot->destroy(sk); <--- sock_map_destroy
sk_psock_stop(, true); <--- true so cancel workqueue
cancel_work_sync() <--- splat, because *_bh_disable()
We can not call cancel_work_sync() from inside destroy path. So mark
the sk_psock_stop call to skip this cancel_work_sync(). This will avoid
the BUG, but means we may run sk_psock_backlog after or during the
destroy op. We zapped the ingress_skb queue in sk_psock_stop (safe to
do with local_bh_disable) so its empty and the sk_psock_backlog work
item will not find any pkts to process here. However, because we are
not going to wait for it or clear its ->state its possible it kicks off
or is already running. This should be 'safe' up until psock drops its
refcnt to psock->sk. The sock_put() that drops this reference is only
done at psock destroy time from sk_psock_destroy(). This is done through
workqueue when sk_psock_drop() is called on psock refnt reaches 0.
And importantly sk_psock_destroy() does a cancel_work_sync(). So trivial
fix works.
I've had hit or miss luck reproducing this caught it once or twice with
the provided reproducer when running with many runners. However, syzkaller
is very good at reproducing so relying on syzkaller to verify fix.
Fixes: d8616ee2af ("bpf, sockmap: Fix sk->sk_forward_alloc warn_on in sk_stream_kill_queues")
Reported-by: syzbot+140186ceba0c496183bc@syzkaller.appspotmail.com
Suggested-by: Hillf Danton <hdanton@sina.com>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Wang Yufen <wangyufen@huawei.com>
Link: https://lore.kernel.org/bpf/20220628035803.317876-1-john.fastabend@gmail.com
Stable-dep-of: 8bbabb3fdd ("bpf, sock_map: Move cancel_work_sync() out of sock lock")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d8616ee2af ]
During TCP sockmap redirect pressure test, the following warning is triggered:
WARNING: CPU: 3 PID: 2145 at net/core/stream.c:205 sk_stream_kill_queues+0xbc/0xd0
CPU: 3 PID: 2145 Comm: iperf Kdump: loaded Tainted: G W 5.10.0+ #9
Call Trace:
inet_csk_destroy_sock+0x55/0x110
inet_csk_listen_stop+0xbb/0x380
tcp_close+0x41b/0x480
inet_release+0x42/0x80
__sock_release+0x3d/0xa0
sock_close+0x11/0x20
__fput+0x9d/0x240
task_work_run+0x62/0x90
exit_to_user_mode_prepare+0x110/0x120
syscall_exit_to_user_mode+0x27/0x190
entry_SYSCALL_64_after_hwframe+0x44/0xa9
The reason we observed is that:
When the listener is closing, a connection may have completed the three-way
handshake but not accepted, and the client has sent some packets. The child
sks in accept queue release by inet_child_forget()->inet_csk_destroy_sock(),
but psocks of child sks have not released.
To fix, add sock_map_destroy to release psocks.
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Jakub Sitnicki <jakub@cloudflare.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20220524075311.649153-1-wangyufen@huawei.com
Stable-dep-of: 8bbabb3fdd ("bpf, sock_map: Move cancel_work_sync() out of sock lock")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b5bcb94b09 ]
If hid_add_device() returns error, it should call hid_destroy_device()
to free hid_dev which is allocated in hid_allocate_device().
Fixes: 74c4fb0580 ("HID: hv_mouse: Properly add the hid device")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 34de8e6e0e ]
When using bpftool to pin {PROG, MAP, LINK} without FILE,
segmentation fault will occur. The reson is that the lack
of FILE will cause strlen to trigger NULL pointer dereference.
The corresponding stacktrace is shown below:
do_pin
do_pin_any
do_pin_fd
mount_bpffs_for_pin
strlen(name) <- NULL pointer dereference
Fix it by adding validation to the common process.
Fixes: 75a1e792c3 ("tools: bpftool: Allow all prog/map handles for pinning objects")
Signed-off-by: Pu Lehui <pulehui@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Quentin Monnet <quentin@isovalent.com>
Link: https://lore.kernel.org/bpf/20221102084034.3342995-1-pulehui@huaweicloud.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ec95b9471 ]
When running `test_sockmap` selftests, the following warning appears:
WARNING: CPU: 2 PID: 197 at net/core/stream.c:205 sk_stream_kill_queues+0xd3/0xf0
Call Trace:
<TASK>
inet_csk_destroy_sock+0x55/0x110
tcp_rcv_state_process+0xd28/0x1380
? tcp_v4_do_rcv+0x77/0x2c0
tcp_v4_do_rcv+0x77/0x2c0
__release_sock+0x106/0x130
__tcp_close+0x1a7/0x4e0
tcp_close+0x20/0x70
inet_release+0x3c/0x80
__sock_release+0x3a/0xb0
sock_close+0x14/0x20
__fput+0xa3/0x260
task_work_run+0x59/0xb0
exit_to_user_mode_prepare+0x1b3/0x1c0
syscall_exit_to_user_mode+0x19/0x50
do_syscall_64+0x48/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
The root case is in commit 84472b436e ("bpf, sockmap: Fix more uncharged
while msg has more_data"), where I used msg->sg.size to replace the tosend,
causing breakage:
if (msg->apply_bytes && msg->apply_bytes < tosend)
tosend = psock->apply_bytes;
Fixes: 84472b436e ("bpf, sockmap: Fix more uncharged while msg has more_data")
Reported-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/bpf/1667266296-8794-1-git-send-email-wangyufen@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 42378a9ca5 ]
If an error (NULL) is returned by krealloc(), callers of realloc_array()
were setting their allocation pointers to NULL, but on error krealloc()
does not touch the original allocation. This would result in a memory
resource leak. Instead, free the old allocation on the error handling
path.
The memory leak information is as follows as also reported by Zhengchao:
unreferenced object 0xffff888019801800 (size 256):
comm "bpf_repo", pid 6490, jiffies 4294959200 (age 17.170s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<00000000b211474b>] __kmalloc_node_track_caller+0x45/0xc0
[<0000000086712a0b>] krealloc+0x83/0xd0
[<00000000139aab02>] realloc_array+0x82/0xe2
[<00000000b1ca41d1>] grow_stack_state+0xfb/0x186
[<00000000cd6f36d2>] check_mem_access.cold+0x141/0x1341
[<0000000081780455>] do_check_common+0x5358/0xb350
[<0000000015f6b091>] bpf_check.cold+0xc3/0x29d
[<000000002973c690>] bpf_prog_load+0x13db/0x2240
[<00000000028d1644>] __sys_bpf+0x1605/0x4ce0
[<00000000053f29bd>] __x64_sys_bpf+0x75/0xb0
[<0000000056fedaf5>] do_syscall_64+0x35/0x80
[<000000002bd58261>] entry_SYSCALL_64_after_hwframe+0x63/0xcd
Fixes: c69431aab6 ("bpf: verifier: Improve function state reallocation")
Reported-by: Zhengchao Shao <shaozhengchao@huawei.com>
Reported-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Bill Wendling <morbo@google.com>
Cc: Lorenz Bauer <oss@lmb.io>
Link: https://lore.kernel.org/bpf/20221029025433.2533810-1-keescook@chromium.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 57b962e627 ]
In the function query_regdb_file() the alpha2 parameter is duplicated
using kmemdup() and subsequently freed in regdb_fw_cb(). However,
request_firmware_nowait() can fail without calling regdb_fw_cb() and
thus leak memory.
Fixes: 007f6c5e6e ("cfg80211: support loading regulatory database as firmware file")
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03c0ad4b06 ]
All we're going to do with this pointer is assign it to
another __rcu pointer, but sparse can't see that, so
use rcu_access_pointer() to silence the warning here.
Fixes: c90b93b5b7 ("wifi: cfg80211: update hidden BSSes to avoid WARN_ON")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1f84eef31 ]
If CPU page fault in a page with zone_device_data svm_bo from another
process, that means it is COW mapping in the child process and the
range is migrated to VRAM by parent process. Migrate the parent
process range back to system memory to recover the CPU page fault.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stable-dep-of: 5b994354af ("drm/amdkfd: Fix NULL pointer dereference in svm_migrate_to_ram()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6283010e2 ]
[Why]:
When we call hmm_range_fault to map memory after a migration, we don't
expect memory to be migrated again as a result of hmm_range_fault. The
driver ensures that all memory is in GPU-accessible locations so that
no migration should be needed. However, there is one corner case where
hmm_range_fault can unexpectedly cause a migration from DEVICE_PRIVATE
back to system memory due to a write-fault when a system memory page in
the same range was mapped read-only (e.g. COW). Ranges with individual
pages in different locations are usually the result of failed page
migrations (e.g. page lock contention). The unexpected migration back
to system memory causes a deadlock from recursive locking in our
driver.
[How]:
Creating a task reference new member under svm_range_list struct.
Setting this with "current" reference, right before the hmm_range_fault
is called. This member is checked against "current" reference at
svm_migrate_to_ram callback function. If equal, the migration will be
ignored.
Signed-off-by: Alex Sierra <alex.sierra@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stable-dep-of: 5b994354af ("drm/amdkfd: Fix NULL pointer dereference in svm_migrate_to_ram()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9fa248c65b ]
There's a race in fuse's readdir cache that can result in an uninitilized
page being read. The page lock is supposed to prevent this from happening
but in the following case it doesn't:
Two fuse_add_dirent_to_cache() start out and get the same parameters
(size=0,offset=0). One of them wins the race to create and lock the page,
after which it fills in data, sets rdc.size and unlocks the page.
In the meantime the page gets evicted from the cache before the other
instance gets to run. That one also creates the page, but finds the
size to be mismatched, bails out and leaves the uninitialized page in the
cache.
Fix by marking a filled page uptodate and ignoring non-uptodate pages.
Reported-by: Frank Sorenson <fsorenso@redhat.com>
Fixes: 5d7bc7e868 ("fuse: allow using readdir cache")
Cc: <stable@vger.kernel.org> # v4.20
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b60e31bf18 upstream.
If the boot firmware implements a connection manager of its own it may
create a DisplayPort tunnel and will be handed off to Linux connection
manager, but the DP OUT resource is not saved in the dp_resource list.
This patch adds tunnelled DP OUT port to the dp_resource list once the
DP tunnel is discovered.
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Tested-by: Renjith Pananchikkal <Renjith.Pananchikkal@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: "Limonciello, Mario" <Mario.Limonciello@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 43bddb26e2 upstream.
If the boot firmware implements connection manager of its own it may not
create the paths in the same way or order we do. For example it may
create first PCIe tunnel and then USB3 tunnel. When we restore our
tunnels (first de-activating them) we may be doing that over completely
different tunnels and that leaves them possibly non-functional. For this
reason we re-use the tunnel discovery functionality and find out all the
existing tunnels, and tear them down. Once that is done we can restore
our tunnels.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: "Limonciello, Mario" <Mario.Limonciello@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the wrongly changed 'limiter volume' display back to -50dB minimum
and sets the correct minimum volume level to -144dB to be aligned with
the controls and display in alsamixer etc.
Signed-off-by: Joerg Schambacher <joerg@hifiberry.com>
Commit 056d3fed3d ("tee: add tee_shm_register_{user,kernel}_buf()")
refactored tee_shm_register() into corresponding user and kernel space
functions named tee_shm_register_{user,kernel}_buf(). The upstream fix
commit 573ae4f13f ("tee: add overflow check in register_shm_helper()")
only applied to tee_shm_register_user_buf().
But the stable kernel 4.19, 5.4, 5.10 and 5.15 don't have the above
mentioned tee_shm_register() refactoring commit. Hence a direct backport
wasn't possible and the fix has to be rather applied to
tee_ioctl_shm_register().
Somehow the fix was correctly backported to 4.19 and 5.4 stable kernels
but the backports for 5.10 and 5.15 stable kernels were broken as fix
was applied to common tee_shm_register() function which broke its kernel
space users such as trusted keys driver.
Fortunately the backport for 5.10 stable kernel was incidently fixed by:
commit 606fe84a4185 ("tee: fix memory leak in tee_shm_register()"). So
fix the backport for 5.15 stable kernel as well.
Fixes: 578c349570d2 ("tee: add overflow check in register_shm_helper()")
Cc: stable@vger.kernel.org # 5.15
Reported-by: Sahil Malhotra <sahil.malhotra@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ad8f9e6994 upstream.
Update the emulation mode when handling writes to CR0, because
toggling CR0.PE switches between Real and Protected Mode, and toggling
CR0.PG when EFER.LME=1 switches between Long and Protected Mode.
This is likely a benign bug because there is no writeback of state,
other than the RIP increment, and when toggling CR0.PE, the CPU has
to execute code from a very low memory address.
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20221025124741.228045-14-mlevitsk@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d087e0f79f upstream.
Some instructions update the cpu execution mode, which needs to update the
emulation mode.
Extract this code, and make assign_eip_far use it.
assign_eip_far now reads CS, instead of getting it via a parameter,
which is ok, because callers always assign CS to the same value
before calling this function.
No functional change is intended.
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20221025124741.228045-12-mlevitsk@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5015bb89b5 upstream.
SYSEXIT is one of the instructions that can change the
processor mode, thus ctxt->mode should be updated after it.
Note that this is likely a benign bug, because the only problematic
mode change is from 32 bit to 64 bit which can lead to truncation of RIP,
and it is not possible to do with sysexit,
since sysexit running in 32 bit mode will be limited to 32 bit version.
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20221025124741.228045-11-mlevitsk@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b6bcdc9f6b upstream.
enter_exception64() performs an MTE check, which involves dereferencing
vcpu->kvm. While vcpu has already been fixed up to be a HYP VA pointer,
kvm is still a pointer in the kernel VA space.
This only affects nVHE configurations with MTE enabled, as in other
cases, the pointer is either valid (VHE) or not dereferenced (!MTE).
Fix this by first converting kvm to a HYP VA pointer.
Fixes: ea7fc1bb1c ("KVM: arm64: Introduce MTE VM feature")
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Reviewed-by: Steven Price <steven.price@arm.com>
[maz: commit message tidy-up]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221027120945.29679-1-ryan.roberts@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c1a41497a upstream.
Clear enable_sgx if ENCLS-exiting is not supported, i.e. if SGX cannot be
virtualized. When KVM is loaded, adjust_vmx_controls checks that the
bit is available before enabling the feature; however, other parts of the
code check enable_sgx and not clearing the variable caused two different
bugs, mostly affecting nested virtualization scenarios.
First, because enable_sgx remained true, SECONDARY_EXEC_ENCLS_EXITING
would be marked available in the capability MSR that are accessed by a
nested hypervisor. KVM would then propagate the control from vmcs12
to vmcs02 even if it isn't supported by the processor, thus causing an
unexpected VM-Fail (exit code 0x7) in L1.
Second, vmx_set_cpu_caps() would not clear the SGX bits when hardware
support is unavailable. This is a much less problematic bug as it only
happens if SGX is soft-disabled (available in the processor but hidden
in CPUID) or if SGX is supported for bare metal but not in the VMCS
(will never happen when running on bare metal, but can theoertically
happen when running in a VM).
Last but not least, this ensures that module params in sysfs reflect
KVM's actual configuration.
RHBZ: https://bugzilla.redhat.com/show_bug.cgi?id=2127128
Fixes: 72add915fb ("KVM: VMX: Enable SGX virtualization for SGX1, SGX2 and LC")
Cc: stable@vger.kernel.org
Suggested-by: Sean Christopherson <seanjc@google.com>
Suggested-by: Bandan Das <bsd@redhat.com>
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Message-Id: <20221025123749.2201649-1-eesposit@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0469e56a14 upstream.
KVM_GET_SUPPORTED_CPUID should only enumerate features that KVM
actually supports. CPUID.80000001:EBX[27:16] are reserved bits and
should be masked off.
Fixes: 0771671749 ("KVM: Enhance guest cpuid management")
Signed-off-by: Jim Mattson <jmattson@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7030d8530e upstream.
KVM_GET_SUPPORTED_CPUID should only enumerate features that KVM
actually supports. The following ranges of CPUID.80000008H are reserved
and should be masked off:
ECX[31:18]
ECX[11:8]
In addition, the PerfTscSize field at ECX[17:16] should also be zero
because KVM does not set the PERFTSC bit at CPUID.80000001H.ECX[27].
Fixes: 24c82e576b ("KVM: Sanitize cpuid")
Signed-off-by: Jim Mattson <jmattson@google.com>
Message-Id: <20220929225203.2234702-3-jmattson@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9440c42941 upstream.
With just the forward declaration of the 'struct pt_regs' in
syscall_wrapper.h, the syscall stub functions:
__[x64|ia32]_sys_*(struct pt_regs *regs)
will have different definition of 'regs' argument in BTF data
based on which object file they are defined in.
If the syscall's object includes 'struct pt_regs' definition,
the BTF argument data will point to a 'struct pt_regs' record,
like:
[226] STRUCT 'pt_regs' size=168 vlen=21
'r15' type_id=1 bits_offset=0
'r14' type_id=1 bits_offset=64
'r13' type_id=1 bits_offset=128
...
If not, it will point to a fwd declaration record:
[15439] FWD 'pt_regs' fwd_kind=struct
and make bpf tracing program hooking on those functions unable
to access fields from 'struct pt_regs'.
Include asm/ptrace.h directly in syscall_wrapper.h to make sure all
syscalls see 'struct pt_regs' definition. This then results in BTF for
'__*_sys_*(struct pt_regs *regs)' functions to point to the actual
struct, not just the forward declaration.
[ bp: No Fixes tag as this is not really a bug fix but "adjustment" so
that BTF is happy. ]
Reported-by: Akihiro HARAI <jharai0815@gmail.com>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Cc: <stable@vger.kernel.org> # this is needed only for BTF so kernels >= 5.15
Link: https://lore.kernel.org/r/20221018122708.823792-1-jolsa@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 17a0bc9bd6 upstream.
The rec_len field in the directory entry has to be a multiple of 4. A
corrupted filesystem image can be used to hit a BUG() in
ext4_rec_len_to_disk(), called from make_indexed_dir().
------------[ cut here ]------------
kernel BUG at fs/ext4/ext4.h:2413!
...
RIP: 0010:make_indexed_dir+0x53f/0x5f0
...
Call Trace:
<TASK>
? add_dirent_to_buf+0x1b2/0x200
ext4_add_entry+0x36e/0x480
ext4_add_nondir+0x2b/0xc0
ext4_create+0x163/0x200
path_openat+0x635/0xe90
do_filp_open+0xb4/0x160
? __create_object.isra.0+0x1de/0x3b0
? _raw_spin_unlock+0x12/0x30
do_sys_openat2+0x91/0x150
__x64_sys_open+0x6c/0xa0
do_syscall_64+0x3c/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
The fix simply adds a call to ext4_check_dir_entry() to validate the
directory entry, returning -EFSCORRUPTED if the entry is invalid.
CC: stable@kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216540
Signed-off-by: Luís Henriques <lhenriques@suse.de>
Link: https://lore.kernel.org/r/20221012131330.32456-1-lhenriques@suse.de
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b6ae0962b upstream.
Avoid that the hardware path is shown twice in the kernel log, and clean
up the output of the version numbers to show up in the same order as
they are listed in the hardware database in the hardware.c file.
Additionally, optimize the memory footprint of the hardware database
and mark some code as init code.
Fixes: cab56b51ec ("parisc: Fix device names in /proc/iomem")
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org> # v4.9+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e8a18e3f00 upstream.
Although the name of the driver 8250_gsc.c suggests that it handles
only serial ports on the GSC bus, it does handle serial ports listed
in the parisc machine inventory as well, e.g. the serial ports in a
C8000 PCI-only workstation.
Change the dependency to CONFIG_PARISC, so that the driver gets included
in the kernel even if CONFIG_GSC isn't set.
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d866e38c7 upstream.
EFI runtime services data is guaranteed to be preserved by the OS,
making it a suitable candidate for the EFI random seed table, which may
be passed to kexec kernels as well (after refreshing the seed), and so
we need to ensure that the memory is preserved without support from the
OS itself.
However, runtime services data is intended for allocations that are
relevant to the implementations of the runtime services themselves, and
so they are unmapped from the kernel linear map, and mapped into the EFI
page tables that are active while runtime service invocations are in
progress. None of this is needed for the RNG seed.
So let's switch to EFI 'ACPI reclaim' memory: in spite of the name,
there is nothing exclusively ACPI about it, it is simply a type of
allocation that carries firmware provided data which may or may not be
relevant to the OS, and it is left up to the OS to decide whether to
reclaim it after having consumed its contents.
Given that in Linux, we never reclaim these allocations, it is a good
choice for the EFI RNG seed, as the allocation is guaranteed to survive
kexec reboots.
One additional reason for changing this now is to align it with the
upcoming recommendation for EFI bootloader provided RNG seeds, which
must not use EFI runtime services code/data allocations.
Cc: <stable@vger.kernel.org> # v4.14+
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 161a438d73 upstream.
We no longer need at least 64 bytes of random seed to permit the early
crng init to complete. The RNG is now based on Blake2s, so reduce the
EFI seed size to the Blake2s hash size, which is sufficient for our
purposes.
While at it, drop the READ_ONCE(), which was supposed to prevent size
from being evaluated after seed was unmapped. However, this cannot
actually happen, so READ_ONCE() is unnecessary here.
Cc: <stable@vger.kernel.org> # v4.14+
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Jason A. Donenfeld <Jason@zx2c4.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8cf0a1bc12 upstream.
In cap_inode_getsecurity(), we will use vfs_getxattr_alloc() to
complete the memory allocation of tmpbuf, if we have completed
the memory allocation of tmpbuf, but failed to call handler->get(...),
there will be a memleak in below logic:
|-- ret = (int)vfs_getxattr_alloc(mnt_userns, ...)
| /* ^^^ alloc for tmpbuf */
|-- value = krealloc(*xattr_value, error + 1, flags)
| /* ^^^ alloc memory */
|-- error = handler->get(handler, ...)
| /* error! */
|-- *xattr_value = value
| /* xattr_value is &tmpbuf (memory leak!) */
So we will try to free(tmpbuf) after vfs_getxattr_alloc() fails to fix it.
Cc: stable@vger.kernel.org
Fixes: 8db6c34f1d ("Introduce v3 namespaced file capabilities")
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Acked-by: Serge Hallyn <serge@hallyn.com>
[PM: subject line and backtrace tweaks]
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b3f4f51ea6 upstream.
The C standard says that memcmp() must treat the buffers as consisting
of "unsigned chars". If char happens to be unsigned, the casts are ok,
but then obviously the c1 variable can never contain a negative
value. And when char is signed, the casts are wrong, and there's still
a problem with using an 8-bit quantity to hold the difference, because
that can range from -255 to +255.
For example, assuming char is signed, comparing two 1-byte buffers,
one containing 0x00 and another 0x80, the current implementation would
return -128 for both memcmp(a, b, 1) and memcmp(b, a, 1), whereas one
of those should of course return something positive.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Fixes: 66b6f755ad ("rcutorture: Import a copy of nolibc")
Cc: stable@vger.kernel.org # v5.0+
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 11052589cf upstream.
Commit e21145a987 ("ipv4: namespacify ip_early_demux sysctl knob") made
it possible to enable/disable early_demux on a per-netns basis. Then, we
introduced two knobs, tcp_early_demux and udp_early_demux, to switch it for
TCP/UDP in commit dddb64bcb3 ("net: Add sysctl to toggle early demux for
tcp and udp"). However, the .proc_handler() was wrong and actually
disabled us from changing the behaviour in each netns.
We can execute early_demux if net.ipv4.ip_early_demux is on and each proto
.early_demux() handler is not NULL. When we toggle (tcp|udp)_early_demux,
the change itself is saved in each netns variable, but the .early_demux()
handler is a global variable, so the handler is switched based on the
init_net's sysctl variable. Thus, netns (tcp|udp)_early_demux knobs have
nothing to do with the logic. Whether we CAN execute proto .early_demux()
is always decided by init_net's sysctl knob, and whether we DO it or not is
by each netns ip_early_demux knob.
This patch namespacifies (tcp|udp)_early_demux again. For now, the users
of the .early_demux() handler are TCP and UDP only, and they are called
directly to avoid retpoline. So, we can remove the .early_demux() handler
from inet6?_protos and need not dereference them in ip6?_rcv_finish_core().
If another proto needs .early_demux(), we can restore it at that time.
Fixes: dddb64bcb3 ("net: Add sysctl to toggle early demux for tcp and udp")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20220713175207.7727-1-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0e792b89e6 upstream.
KASAN reported a use-after-free with ftrace ops [1]. It was found from
vmcore that perf had registered two ops with the same content
successively, both dynamic. After unregistering the second ops, a
use-after-free occurred.
In ftrace_shutdown(), when the second ops is unregistered, the
FTRACE_UPDATE_CALLS command is not set because there is another enabled
ops with the same content. Also, both ops are dynamic and the ftrace
callback function is ftrace_ops_list_func, so the
FTRACE_UPDATE_TRACE_FUNC command will not be set. Eventually the value
of 'command' will be 0 and ftrace_shutdown() will skip the rcu
synchronization.
However, ftrace may be activated. When the ops is released, another CPU
may be accessing the ops. Add the missing synchronization to fix this
problem.
[1]
BUG: KASAN: use-after-free in __ftrace_ops_list_func kernel/trace/ftrace.c:7020 [inline]
BUG: KASAN: use-after-free in ftrace_ops_list_func+0x2b0/0x31c kernel/trace/ftrace.c:7049
Read of size 8 at addr ffff56551965bbc8 by task syz-executor.2/14468
CPU: 1 PID: 14468 Comm: syz-executor.2 Not tainted 5.10.0 #7
Hardware name: linux,dummy-virt (DT)
Call trace:
dump_backtrace+0x0/0x40c arch/arm64/kernel/stacktrace.c:132
show_stack+0x30/0x40 arch/arm64/kernel/stacktrace.c:196
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1b4/0x248 lib/dump_stack.c:118
print_address_description.constprop.0+0x28/0x48c mm/kasan/report.c:387
__kasan_report mm/kasan/report.c:547 [inline]
kasan_report+0x118/0x210 mm/kasan/report.c:564
check_memory_region_inline mm/kasan/generic.c:187 [inline]
__asan_load8+0x98/0xc0 mm/kasan/generic.c:253
__ftrace_ops_list_func kernel/trace/ftrace.c:7020 [inline]
ftrace_ops_list_func+0x2b0/0x31c kernel/trace/ftrace.c:7049
ftrace_graph_call+0x0/0x4
__might_sleep+0x8/0x100 include/linux/perf_event.h:1170
__might_fault mm/memory.c:5183 [inline]
__might_fault+0x58/0x70 mm/memory.c:5171
do_strncpy_from_user lib/strncpy_from_user.c:41 [inline]
strncpy_from_user+0x1f4/0x4b0 lib/strncpy_from_user.c:139
getname_flags+0xb0/0x31c fs/namei.c:149
getname+0x2c/0x40 fs/namei.c:209
[...]
Allocated by task 14445:
kasan_save_stack+0x24/0x50 mm/kasan/common.c:48
kasan_set_track mm/kasan/common.c:56 [inline]
__kasan_kmalloc mm/kasan/common.c:479 [inline]
__kasan_kmalloc.constprop.0+0x110/0x13c mm/kasan/common.c:449
kasan_kmalloc+0xc/0x14 mm/kasan/common.c:493
kmem_cache_alloc_trace+0x440/0x924 mm/slub.c:2950
kmalloc include/linux/slab.h:563 [inline]
kzalloc include/linux/slab.h:675 [inline]
perf_event_alloc.part.0+0xb4/0x1350 kernel/events/core.c:11230
perf_event_alloc kernel/events/core.c:11733 [inline]
__do_sys_perf_event_open kernel/events/core.c:11831 [inline]
__se_sys_perf_event_open+0x550/0x15f4 kernel/events/core.c:11723
__arm64_sys_perf_event_open+0x6c/0x80 kernel/events/core.c:11723
[...]
Freed by task 14445:
kasan_save_stack+0x24/0x50 mm/kasan/common.c:48
kasan_set_track+0x24/0x34 mm/kasan/common.c:56
kasan_set_free_info+0x20/0x40 mm/kasan/generic.c:358
__kasan_slab_free.part.0+0x11c/0x1b0 mm/kasan/common.c:437
__kasan_slab_free mm/kasan/common.c:445 [inline]
kasan_slab_free+0x2c/0x40 mm/kasan/common.c:446
slab_free_hook mm/slub.c:1569 [inline]
slab_free_freelist_hook mm/slub.c:1608 [inline]
slab_free mm/slub.c:3179 [inline]
kfree+0x12c/0xc10 mm/slub.c:4176
perf_event_alloc.part.0+0xa0c/0x1350 kernel/events/core.c:11434
perf_event_alloc kernel/events/core.c:11733 [inline]
__do_sys_perf_event_open kernel/events/core.c:11831 [inline]
__se_sys_perf_event_open+0x550/0x15f4 kernel/events/core.c:11723
[...]
Link: https://lore.kernel.org/linux-trace-kernel/20221103031010.166498-1-lihuafei1@huawei.com
Fixes: edb096e007 ("ftrace: Fix memleak when unregistering dynamic ops when tracing disabled")
Cc: stable@vger.kernel.org
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Li Huafei <lihuafei1@huawei.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 968b715831 upstream.
We have been seeing the following panic in production
kernel BUG at fs/btrfs/tree-mod-log.c:677!
invalid opcode: 0000 [#1] SMP
RIP: 0010:tree_mod_log_rewind+0x1b4/0x200
RSP: 0000:ffffc9002c02f890 EFLAGS: 00010293
RAX: 0000000000000003 RBX: ffff8882b448c700 RCX: 0000000000000000
RDX: 0000000000008000 RSI: 00000000000000a7 RDI: ffff88877d831c00
RBP: 0000000000000002 R08: 000000000000009f R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000100c40 R12: 0000000000000001
R13: ffff8886c26d6a00 R14: ffff88829f5424f8 R15: ffff88877d831a00
FS: 00007fee1d80c780(0000) GS:ffff8890400c0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fee1963a020 CR3: 0000000434f33002 CR4: 00000000007706e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
btrfs_get_old_root+0x12b/0x420
btrfs_search_old_slot+0x64/0x2f0
? tree_mod_log_oldest_root+0x3d/0xf0
resolve_indirect_ref+0xfd/0x660
? ulist_alloc+0x31/0x60
? kmem_cache_alloc_trace+0x114/0x2c0
find_parent_nodes+0x97a/0x17e0
? ulist_alloc+0x30/0x60
btrfs_find_all_roots_safe+0x97/0x150
iterate_extent_inodes+0x154/0x370
? btrfs_search_path_in_tree+0x240/0x240
iterate_inodes_from_logical+0x98/0xd0
? btrfs_search_path_in_tree+0x240/0x240
btrfs_ioctl_logical_to_ino+0xd9/0x180
btrfs_ioctl+0xe2/0x2ec0
? __mod_memcg_lruvec_state+0x3d/0x280
? do_sys_openat2+0x6d/0x140
? kretprobe_dispatcher+0x47/0x70
? kretprobe_rethook_handler+0x38/0x50
? rethook_trampoline_handler+0x82/0x140
? arch_rethook_trampoline_callback+0x3b/0x50
? kmem_cache_free+0xfb/0x270
? do_sys_openat2+0xd5/0x140
__x64_sys_ioctl+0x71/0xb0
do_syscall_64+0x2d/0x40
Which is this code in tree_mod_log_rewind()
switch (tm->op) {
case BTRFS_MOD_LOG_KEY_REMOVE_WHILE_FREEING:
BUG_ON(tm->slot < n);
This occurs because we replay the nodes in order that they happened, and
when we do a REPLACE we will log a REMOVE_WHILE_FREEING for every slot,
starting at 0. 'n' here is the number of items in this block, which in
this case was 1, but we had 2 REMOVE_WHILE_FREEING operations.
The actual root cause of this was that we were replaying operations for
a block that shouldn't have been replayed. Consider the following
sequence of events
1. We have an already modified root, and we do a btrfs_get_tree_mod_seq().
2. We begin removing items from this root, triggering KEY_REPLACE for
it's child slots.
3. We remove one of the 2 children this root node points to, thus triggering
the root node promotion of the remaining child, and freeing this node.
4. We modify a new root, and re-allocate the above node to the root node of
this other root.
The tree mod log looks something like this
logical 0 op KEY_REPLACE (slot 1) seq 2
logical 0 op KEY_REMOVE (slot 1) seq 3
logical 0 op KEY_REMOVE_WHILE_FREEING (slot 0) seq 4
logical 4096 op LOG_ROOT_REPLACE (old logical 0) seq 5
logical 8192 op KEY_REMOVE_WHILE_FREEING (slot 1) seq 6
logical 8192 op KEY_REMOVE_WHILE_FREEING (slot 0) seq 7
logical 0 op LOG_ROOT_REPLACE (old logical 8192) seq 8
>From here the bug is triggered by the following steps
1. Call btrfs_get_old_root() on the new_root.
2. We call tree_mod_log_oldest_root(btrfs_root_node(new_root)), which is
currently logical 0.
3. tree_mod_log_oldest_root() calls tree_mod_log_search_oldest(), which
gives us the KEY_REPLACE seq 2, and since that's not a
LOG_ROOT_REPLACE we incorrectly believe that we don't have an old
root, because we expect that the most recent change should be a
LOG_ROOT_REPLACE.
4. Back in tree_mod_log_oldest_root() we don't have a LOG_ROOT_REPLACE,
so we don't set old_root, we simply use our existing extent buffer.
5. Since we're using our existing extent buffer (logical 0) we call
tree_mod_log_search(0) in order to get the newest change to start the
rewind from, which ends up being the LOG_ROOT_REPLACE at seq 8.
6. Again since we didn't find an old_root we simply clone logical 0 at
it's current state.
7. We call tree_mod_log_rewind() with the cloned extent buffer.
8. Set n = btrfs_header_nritems(logical 0), which would be whatever the
original nritems was when we COWed the original root, say for this
example it's 2.
9. We start from the newest operation and work our way forward, so we
see LOG_ROOT_REPLACE which we ignore.
10. Next we see KEY_REMOVE_WHILE_FREEING for slot 0, which triggers the
BUG_ON(tm->slot < n), because it expects if we've done this we have a
completely empty extent buffer to replay completely.
The correct thing would be to find the first LOG_ROOT_REPLACE, and then
get the old_root set to logical 8192. In fact making that change fixes
this particular problem.
However consider the much more complicated case. We have a child node
in this tree and the above situation. In the above case we freed one
of the child blocks at the seq 3 operation. If this block was also
re-allocated and got new tree mod log operations we would have a
different problem. btrfs_search_old_slot(orig root) would get down to
the logical 0 root that still pointed at that node. However in
btrfs_search_old_slot() we call tree_mod_log_rewind(buf) directly. This
is not context aware enough to know which operations we should be
replaying. If the block was re-allocated multiple times we may only
want to replay a range of operations, and determining what that range is
isn't possible to determine.
We could maybe solve this by keeping track of which root the node
belonged to at every tree mod log operation, and then passing this
around to make sure we're only replaying operations that relate to the
root we're trying to rewind.
However there's a simpler way to solve this problem, simply disallow
reallocations if we have currently running tree mod log users. We
already do this for leaf's, so we're simply expanding this to nodes as
well. This is a relatively uncommon occurrence, and the problem is
complicated enough I'm worried that we will still have corner cases in
the reallocation case. So fix this in the most straightforward way
possible.
Fixes: bd989ba359 ("Btrfs: add tree modification log functions")
CC: stable@vger.kernel.org # 3.3+
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8184620ae2 upstream.
When doing a direct IO write using a iocb with nowait and dsync set, we
end up not syncing the file once the write completes.
This is because we tell iomap to not call generic_write_sync(), which
would result in calling btrfs_sync_file(), in order to avoid a deadlock
since iomap can call it while we are holding the inode's lock and
btrfs_sync_file() needs to acquire the inode's lock. The deadlock happens
only if the write happens synchronously, when iomap_dio_rw() calls
iomap_dio_complete() before it returns. Instead we do the sync ourselves
at btrfs_do_write_iter().
For a nowait write however we can end up not doing the sync ourselves at
at btrfs_do_write_iter() because the write could have been queued, and
therefore we get -EIOCBQUEUED returned from iomap in such case. That makes
us skip the sync call at btrfs_do_write_iter(), as we don't do it for
any error returned from btrfs_direct_write(). We can't simply do the call
even if -EIOCBQUEUED is returned, since that would block the task waiting
for IO, both for the data since there are bios still in progress as well
as potentially blocking when joining a log transaction and when syncing
the log (writing log trees, super blocks, etc).
So let iomap do the sync call itself and in order to avoid deadlocks for
the case of synchronous writes (without nowait), use __iomap_dio_rw() and
have ourselves call iomap_dio_complete() after unlocking the inode.
A test case will later be sent for fstests, after this is fixed in Linus'
tree.
Fixes: 51bd9563b6 ("btrfs: fix deadlock due to page faults during direct IO reads and writes")
Reported-by: Марк Коренберг <socketpair@gmail.com>
Link: https://lore.kernel.org/linux-btrfs/CAEmTpZGRKbzc16fWPvxbr6AfFsQoLmz-Lcg-7OgJOZDboJ+SGQ@mail.gmail.com/
CC: stable@vger.kernel.org # 6.0+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ccd30a476f upstream.
Commit d7e7b9af10 ("fscrypt: stop using keyrings subsystem for
fscrypt_master_key") moved the keyring destruction from __put_super() to
generic_shutdown_super() so that the filesystem's block device(s) are
still available. Unfortunately, this causes a memory leak in the case
where a mount is attempted with the test_dummy_encryption mount option,
but the mount fails after the option has already been processed.
To fix this, attempt the keyring destruction in both places.
Reported-by: syzbot+104c2a89561289cec13e@syzkaller.appspotmail.com
Fixes: d7e7b9af10 ("fscrypt: stop using keyrings subsystem for fscrypt_master_key")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Christian Brauner (Microsoft) <brauner@kernel.org>
Link: https://lore.kernel.org/r/20221011213838.209879-1-ebiggers@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d7e7b9af10 upstream.
The approach of fs/crypto/ internally managing the fscrypt_master_key
structs as the payloads of "struct key" objects contained in a
"struct key" keyring has outlived its usefulness. The original idea was
to simplify the code by reusing code from the keyrings subsystem.
However, several issues have arisen that can't easily be resolved:
- When a master key struct is destroyed, blk_crypto_evict_key() must be
called on any per-mode keys embedded in it. (This started being the
case when inline encryption support was added.) Yet, the keyrings
subsystem can arbitrarily delay the destruction of keys, even past the
time the filesystem was unmounted. Therefore, currently there is no
easy way to call blk_crypto_evict_key() when a master key is
destroyed. Currently, this is worked around by holding an extra
reference to the filesystem's request_queue(s). But it was overlooked
that the request_queue reference is *not* guaranteed to pin the
corresponding blk_crypto_profile too; for device-mapper devices that
support inline crypto, it doesn't. This can cause a use-after-free.
- When the last inode that was using an incompletely-removed master key
is evicted, the master key removal is completed by removing the key
struct from the keyring. Currently this is done via key_invalidate().
Yet, key_invalidate() takes the key semaphore. This can deadlock when
called from the shrinker, since in fscrypt_ioctl_add_key(), memory is
allocated with GFP_KERNEL under the same semaphore.
- More generally, the fact that the keyrings subsystem can arbitrarily
delay the destruction of keys (via garbage collection delay, or via
random processes getting temporary key references) is undesirable, as
it means we can't strictly guarantee that all secrets are ever wiped.
- Doing the master key lookups via the keyrings subsystem results in the
key_permission LSM hook being called. fscrypt doesn't want this, as
all access control for encrypted files is designed to happen via the
files themselves, like any other files. The workaround which SELinux
users are using is to change their SELinux policy to grant key search
access to all domains. This works, but it is an odd extra step that
shouldn't really have to be done.
The fix for all these issues is to change the implementation to what I
should have done originally: don't use the keyrings subsystem to keep
track of the filesystem's fscrypt_master_key structs. Instead, just
store them in a regular kernel data structure, and rework the reference
counting, locking, and lifetime accordingly. Retain support for
RCU-mode key lookups by using a hash table. Replace fscrypt_sb_free()
with fscrypt_sb_delete(), which releases the keys synchronously and runs
a bit earlier during unmount, so that block devices are still available.
A side effect of this patch is that neither the master keys themselves
nor the filesystem keyrings will be listed in /proc/keys anymore.
("Master key users" and the master key users keyrings will still be
listed.) However, this was mostly an implementation detail, and it was
intended just for debugging purposes. I don't know of anyone using it.
This patch does *not* change how "master key users" (->mk_users) works;
that still uses the keyrings subsystem. That is still needed for key
quotas, and changing that isn't necessary to solve the issues listed
above. If we decide to change that too, it would be a separate patch.
I've marked this as fixing the original commit that added the fscrypt
keyring, but as noted above the most important issue that this patch
fixes wasn't introduced until the addition of inline encryption support.
Fixes: 22d94f493b ("fscrypt: add FS_IOC_ADD_ENCRYPTION_KEY ioctl")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20220901193208.138056-2-ebiggers@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a62ed6136 upstream.
syzbot reported a sequence of memory leaks, and one of them indicated we
failed to free a whole sk:
unreferenced object 0xffff8880126e0000 (size 1088):
comm "syz-executor419", pid 326, jiffies 4294773607 (age 12.609s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 7d 00 00 00 00 00 00 00 ........}.......
01 00 07 40 00 00 00 00 00 00 00 00 00 00 00 00 ...@............
backtrace:
[<000000006fefe750>] sk_prot_alloc+0x64/0x2a0 net/core/sock.c:1970
[<0000000074006db5>] sk_alloc+0x3b/0x800 net/core/sock.c:2029
[<00000000728cd434>] unix_create1+0xaf/0x920 net/unix/af_unix.c:928
[<00000000a279a139>] unix_create+0x113/0x1d0 net/unix/af_unix.c:997
[<0000000068259812>] __sock_create+0x2ab/0x550 net/socket.c:1516
[<00000000da1521e1>] sock_create net/socket.c:1566 [inline]
[<00000000da1521e1>] __sys_socketpair+0x1a8/0x550 net/socket.c:1698
[<000000007ab259e1>] __do_sys_socketpair net/socket.c:1751 [inline]
[<000000007ab259e1>] __se_sys_socketpair net/socket.c:1748 [inline]
[<000000007ab259e1>] __x64_sys_socketpair+0x97/0x100 net/socket.c:1748
[<000000007dedddc1>] do_syscall_x64 arch/x86/entry/common.c:50 [inline]
[<000000007dedddc1>] do_syscall_64+0x38/0x90 arch/x86/entry/common.c:80
[<000000009456679f>] entry_SYSCALL_64_after_hwframe+0x63/0xcd
We can reproduce this issue by creating two AF_UNIX SOCK_STREAM sockets,
send()ing an OOB skb to each other, and close()ing them without consuming
the OOB skbs.
int skpair[2];
socketpair(AF_UNIX, SOCK_STREAM, 0, skpair);
send(skpair[0], "x", 1, MSG_OOB);
send(skpair[1], "x", 1, MSG_OOB);
close(skpair[0]);
close(skpair[1]);
Currently, we free an OOB skb in unix_sock_destructor() which is called via
__sk_free(), but it's too late because the receiver's unix_sk(sk)->oob_skb
is accounted against the sender's sk->sk_wmem_alloc and __sk_free() is
called only when sk->sk_wmem_alloc is 0.
In the repro sequences, we do not consume the OOB skb, so both two sk's
sock_put() never reach __sk_free() due to the positive sk->sk_wmem_alloc.
Then, no one can consume the OOB skb nor call __sk_free(), and we finally
leak the two whole sk.
Thus, we must free the unconsumed OOB skb earlier when close()ing the
socket.
Fixes: 314001f0bf ("af_unix: Add OOB support")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Anil Altinay <aaltinay@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 711f8c3fb3 upstream.
The Bluetooth spec states that the valid range for SPSM is from
0x0001-0x00ff so it is invalid to accept values outside of this range:
BLUETOOTH CORE SPECIFICATION Version 5.3 | Vol 3, Part A
page 1059:
Table 4.15: L2CAP_LE_CREDIT_BASED_CONNECTION_REQ SPSM ranges
CVE: CVE-2022-42896
CC: stable@vger.kernel.org
Reported-by: Tamás Koczka <poprdi@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Reviewed-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 569bea74c9 ]
In piix4_probe(), the piix4 adapter will be registered in:
piix4_probe()
piix4_add_adapters_sb800() / piix4_add_adapter()
i2c_add_adapter()
Based on the probed device type, piix4_add_adapters_sb800() or single
piix4_add_adapter() will be called.
For the former case, piix4_adapter_count is set as the number of adapters,
while for antoher case it is not set and kept default *zero*.
When piix4 is removed, piix4_remove() removes the adapters added in
piix4_probe(), basing on the piix4_adapter_count value.
Because the count is zero for the single adapter case, the adapter won't
be removed and makes the sources allocated for adapter leaked, such as
the i2c client and device.
These sources can still be accessed by i2c or bus and cause problems.
An easily reproduced case is that if a new adapter is registered, i2c
will get the leaked adapter and try to call smbus_algorithm, which was
already freed:
Triggered by: rmmod i2c_piix4 && modprobe max31730
BUG: unable to handle page fault for address: ffffffffc053d860
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
Oops: 0000 [#1] PREEMPT SMP KASAN
CPU: 0 PID: 3752 Comm: modprobe Tainted: G
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996)
RIP: 0010:i2c_default_probe (drivers/i2c/i2c-core-base.c:2259) i2c_core
RSP: 0018:ffff888107477710 EFLAGS: 00000246
...
<TASK>
i2c_detect (drivers/i2c/i2c-core-base.c:2302) i2c_core
__process_new_driver (drivers/i2c/i2c-core-base.c:1336) i2c_core
bus_for_each_dev (drivers/base/bus.c:301)
i2c_for_each_dev (drivers/i2c/i2c-core-base.c:1823) i2c_core
i2c_register_driver (drivers/i2c/i2c-core-base.c:1861) i2c_core
do_one_initcall (init/main.c:1296)
do_init_module (kernel/module/main.c:2455)
...
</TASK>
---[ end trace 0000000000000000 ]---
Fix this problem by correctly set piix4_adapter_count as 1 for the
single adapter so it can be normally removed.
Fixes: 528d53a159 ("i2c: piix4: Fix probing of reserved ports on AMD Family 16h Model 30h")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5c921a53c ]
Up until now, the external MDIO controller frequency values relied
either on the default ones out of reset or on those setup by u-boot.
Let's just properly specify the MDC frequency in the DTS so that even
without u-boot's intervention Linux can drive the MDIO bus.
Fixes: 0420dde30a ("arm64: dts: ls208xa: add the external MDIO nodes")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d78a57426e ]
Up until now, the external MDIO controller frequency values relied
either on the default ones out of reset or on those setup by u-boot.
Let's just properly specify the MDC frequency in the DTS so that even
without u-boot's intervention Linux can drive the MDIO bus.
Fixes: bbe75af7b0 ("arm64: dts: ls1088a: add external MDIO device nodes")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c126a0abc5 ]
Up until now, the external MDIO controller frequency values relied
either on the default ones out of reset or on those setup by u-boot.
Let's just properly specify the MDC frequency in the DTS so that even
without u-boot's intervention Linux can drive the MDIO bus.
Fixes: 6e1b8fae89 ("arm64: dts: lx2160a: add emdio1 node")
Fixes: 5705b9dcda ("arm64: dts: lx2160a: add emdio2 node")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb5ad73941 ]
The GW5910 and GW5913 have a user pushbutton that is tied to the
Gateworks System Controller GPIO offset 2. Fix the invalid offset of 0.
Fixes: 64bf0a0af1 ("ARM: dts: imx6qdl-gw: add Gateworks System Controller support")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f4cd18c5b2 ]
memblock_reserve() expects a physical address, but the address being
passed for the TPM final events log is what was returned from
early_memremap(). This results in something like the following:
[ 0.000000] memblock_reserve: [0xffffffffff2c0000-0xffffffffff2c00e4] efi_tpm_eventlog_init+0x324/0x370
Pass the address from efi like what is done for the TPM events log.
Fixes: c46f340569 ("tpm: Reserve the TPM final events table")
Cc: Matthew Garrett <mjg59@google.com>
Cc: Jarkko Sakkinen <jarkko@kernel.org>
Cc: Bartosz Szczepanek <bsz@semihalf.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Acked-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65f8682b9a ]
For asic with VF MMIO access protection avoid using CPU for VM table updates.
CPU pagetable updates have issues with HDP flush as VF MMIO access protection
blocks write to mmBIF_BX_DEV0_EPF0_VF0_HDP_MEM_COHERENCY_FLUSH_CNTL register
during sriov runtime.
v3: introduce virtualization capability flag AMDGPU_VF_MMIO_ACCESS_PROTECT
which indicates that VF MMIO write access is not allowed in sriov runtime
Signed-off-by: Danijel Slivka <danijel.slivka@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79425b297f ]
The MadCatz variant of the MMO7 mouse has the ID 0738:1713 and the same
quirks as the Saitek variant.
Signed-off-by: Samuel Bailey <samuel.bailey1@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2331ce6126 ]
Userspace can currently write to sysfs to transition sdev_state to RUNNING
or OFFLINE from any source state. This causes issues because proper
transitioning out of some states involves steps besides just changing
sdev_state, so allowing userspace to change sdev_state regardless of the
source state can result in inconsistencies; e.g. with ISCSI we can end up
with sdev_state == SDEV_RUNNING while the device queue is quiesced. Any
task attempting I/O on the device will then hang, and in more recent
kernels, iscsid will hang as well.
More detail about this bug is provided in my first attempt:
https://groups.google.com/g/open-iscsi/c/PNKca4HgPDs/m/CXaDkntOAQAJ
Link: https://lore.kernel.org/r/20220924000241.2967323-1-ushankar@purestorage.com
Signed-off-by: Uday Shankar <ushankar@purestorage.com>
Suggested-by: Mike Christie <michael.christie@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ba3e38517 ]
The state argument for the functions for obtaining various parts of the
state is NULL if it is called by drivers for active state. Fail graciously
in that case instead of dereferencing a NULL pointer.
Suggested-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7718999356 ]
v4l2_device_unregister need to be called to put the refcount got by
v4l2_device_register when vdec_probe fails or vdec_remove is called.
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2dc73b4866 ]
I expect that the hardware will have limited this to 16, but just in
case it hasn't, check for this corner case.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 93f65ce036 ]
I expect that the hardware will have limited this to 16, but just in
case it hasn't, check for this corner case.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c53e3a049f ]
The local sd_fmt variable in rkisp1_capture_link_validate() has
uninitialized fields, which causes random failures when calling the
subdev .get_fmt() operation. Fix it by initializing the variable when
declaring it, which zeros all other fields.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4c3501f13e ]
The rkisp1_lsc_config() function incorrectly uses the
RKISP1_CIF_ISP_LSC_SECT_SIZE() macro for the gradient registers. Replace
it with the correct macro, and rename it from
RKISP1_CIF_ISP_LSC_GRAD_SIZE() to RKISP1_CIF_ISP_LSC_SECT_GRAD() as the
corresponding registers store the gradients for each sector, not a size.
This doesn't cause any functional change as the two macros are defined
identically (the size and gradient registers store fields in the same
number of bits at the same positions).
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 83b9296e39 ]
Initialize the four color space fields on the sink and source video pads
of the resizer in the .init_cfg() operation. The resizer can't perform
any color space conversion, so set the sink and source color spaces to
the same defaults, which match the ISP source video pad default.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 711d91497e ]
The rkisp1_csm_config() function takes a pointer to the rkisp1_params
structure which contains the quantization value. There's no need to pass
it separately to the function. Drop it from the function parameters.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b60741127 ]
The channel-subsystem-driver scans for newly available devices whenever
device-IDs are removed from the cio_ignore list using a command such as:
echo free >/proc/cio_ignore
Since an I/O device scan might interfer with running I/Os, commit
172da89ed0 ("s390/cio: avoid excessive path-verification requests")
introduced an optimization to exclude online devices from the scan.
The newly added check for online devices incorrectly assumes that
an I/O-subchannel's drvdata points to a struct io_subchannel_private.
For devices that are bound to a non-default I/O subchannel driver, such
as the vfio_ccw driver, this results in an out-of-bounds read access
during each scan.
Fix this by changing the scan logic to rely on a driver-independent
online indication. For this we can use struct subchannel->config.ena,
which is the driver's requested subchannel-enabled state. Since I/Os
can only be started on enabled subchannels, this matches the intent
of the original optimization of not scanning devices where I/O might
be running.
Fixes: 172da89ed0 ("s390/cio: avoid excessive path-verification requests")
Fixes: 0c3812c347 ("s390/cio: derive cdev information only for IO-subchannels")
Cc: <stable@vger.kernel.org> # v5.15
Reported-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Reviewed-by: Vineeth Vijayan <vneethv@linux.ibm.com>
Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c3812c347 ]
cdev->online for the purge function must not be checked for the
non-IO subchannel type. Make sure that we are deriving the cdev only
from sch-type SUBCHANNEL_TYPE_IO.
Signed-off-by: Vineeth Vijayan <vneethv@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Stable-dep-of: 1b60741127 ("s390/cio: fix out-of-bounds access on cio_ignore free")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e1b5a86a5 ]
For some exception types the instruction address points behind the
instruction that caused the exception. Take that into account and add
the missing exception table entries.
Cc: <stable@vger.kernel.org>
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05e258c6ec ]
There is some code in the parser that tries to read 0x8000
bytes into a block to "read in the middle" of the block. Well
that only works if the block is also 0x10000 bytes all the time,
else we get these parse errors as we reach the end of the flash:
spi-nor spi0.0: mx25l1606e (2048 Kbytes)
mtd_read error while parsing (offset: 0x200000): -22
mtd_read error while parsing (offset: 0x201000): -22
(...)
Fix the code to do what I think was intended.
Cc: stable@vger.kernel.org
Fixes: f0501e81fb ("mtd: bcm47xxpart: alternative MAGIC for board_data partition")
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221018091129.280026-1-linus.walleij@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 776d875fd4 ]
When the text console is scrolling text upwards it calls the fillrect()
function to empty the new line. The current implementation doesn't seem
to work correctly on HCRX cards in 32-bit mode and leave garbage in that
line instead. Fix it by falling back to standard cfb_fillrect() in that
case.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c379c6524 ]
The stifb driver (for Artist/HCRX graphics on PA-RISC) was missing
the fillrect function.
Tested on a 715/64 PA-RISC machine and in qemu.
Signed-off-by: Helge Deller <deller@gmx.de>
Stable-dep-of: 776d875fd4 ("fbdev: stifb: Fall back to cfb_fillrect() on 32-bit HCRX cards")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 088604d37e ]
Quoting the header comments, IRQF_ONESHOT is "Used by threaded interrupts
which need to keep the irq line disabled until the threaded handler has
been run.". When applied to an interrupt that doesn't request a threaded
irq then IRQF_ONESHOT has a lesser known (undocumented?) side effect,
which it to disable the forced threading of irqs. For "normal" kernels
if there is no thread_fn then IRQF_ONESHOT is a nop.
In this case disabling forced threading is not appropriate because the
driver calls wake_up_all() (via msm_hdmi_i2c_irq) and also directly uses
the regular spinlock API for locking (in msm_hdmi_hdcp_irq() ). Neither
of these APIs can be called from no-thread interrupt handlers on
PREEMPT_RT systems.
Fix this by removing IRQF_ONESHOT.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220201174734.196718-3-daniel.thompson@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Stable-dep-of: 152d394842 ("drm/msm/hdmi: fix IRQ lifetime")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 466a85336f ]
Currently vsock_connectible_has_data() may miss a wakeup operation
between vsock_connectible_has_data() == 0 and the prepare_to_wait().
Fix the race by adding the process to the wait queue before checking
vsock_connectible_has_data().
Fixes: b3f7fd5488 ("af_vsock: separate wait data loop")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reported-by: Frédéric Dalleau <frederic.dalleau@docker.com>
Tested-by: Frédéric Dalleau <frederic.dalleau@docker.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 768b3c745f ]
During the initialization of ip6_route_net_init_late(), if file
ipv6_route or rt6_stats fails to be created, the initialization is
successful by default. Therefore, the ipv6_route or rt6_stats file
doesn't be found during the remove in ip6_route_net_exit_late(). It
will cause WRNING.
The following is the stack information:
name 'rt6_stats'
WARNING: CPU: 0 PID: 9 at fs/proc/generic.c:712 remove_proc_entry+0x389/0x460
Modules linked in:
Workqueue: netns cleanup_net
RIP: 0010:remove_proc_entry+0x389/0x460
PKRU: 55555554
Call Trace:
<TASK>
ops_exit_list+0xb0/0x170
cleanup_net+0x4ea/0xb00
process_one_work+0x9bf/0x1710
worker_thread+0x665/0x1080
kthread+0x2e4/0x3a0
ret_from_fork+0x1f/0x30
</TASK>
Fixes: cdb1876192 ("[NETNS][IPV6] route6 - create route6 proc files for the namespace")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20221102020610.351330-1-shaozhengchao@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f8017317cb ]
When IPv6 module gets initialized but hits an error in the middle,
kenel panic with:
KASAN: null-ptr-deref in range [0x0000000000000598-0x000000000000059f]
CPU: 1 PID: 361 Comm: insmod
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996)
RIP: 0010:__neigh_ifdown.isra.0+0x24b/0x370
RSP: 0018:ffff888012677908 EFLAGS: 00000202
...
Call Trace:
<TASK>
neigh_table_clear+0x94/0x2d0
ndisc_cleanup+0x27/0x40 [ipv6]
inet6_init+0x21c/0x2cb [ipv6]
do_one_initcall+0xd3/0x4d0
do_init_module+0x1ae/0x670
...
Kernel panic - not syncing: Fatal exception
When ipv6 initialization fails, it will try to cleanup and calls:
neigh_table_clear()
neigh_ifdown(tbl, NULL)
pneigh_queue_purge(&tbl->proxy_queue, dev_net(dev == NULL))
# dev_net(NULL) triggers null-ptr-deref.
Fix it by passing NULL to pneigh_queue_purge() in neigh_ifdown() if dev
is NULL, to make kernel not panic immediately.
Fixes: 66ba215cb5 ("neigh: fix possible DoS due to net iface start/stop loop")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Denis V. Lunev <den@openvz.org>
Link: https://lore.kernel.org/r/20221101121552.21890-1-chenzhongjin@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62ff373da2 ]
In smc_init(), register_pernet_subsys(&smc_net_stat_ops) is called
without any error handling.
If it fails, registering of &smc_net_ops won't be reverted.
And if smc_nl_init() fails, &smc_net_stat_ops itself won't be reverted.
This leaves wild ops in subsystem linkedlist and when another module
tries to call register_pernet_operations() it triggers page fault:
BUG: unable to handle page fault for address: fffffbfff81b964c
RIP: 0010:register_pernet_operations+0x1b9/0x5f0
Call Trace:
<TASK>
register_pernet_subsys+0x29/0x40
ebtables_init+0x58/0x1000 [ebtables]
...
Fixes: 194730a9be ("net/smc: Make SMC statistics network namespace aware")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Link: https://lore.kernel.org/r/20221101093722.127223-1-chenzhongjin@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ae34111fe ]
In current code "plat->mdio_node" is always NULL, the mdio
support is lost as there is no "mdio_bus_data". The original
driver could work as the "mdio" variable is never set to
false, which is described in commit <b0e03950dd71> ("stmmac:
dwmac-loongson: fix uninitialized variable ......"). And
after this commit merged, the "mdio" variable is always
false, causing the mdio supoort logic lost.
Fixes: 30bba69d7d ("stmmac: pci: Add dwmac support for Loongson")
Signed-off-by: Liu Peibao <liupeibao@loongson.cn>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20221101060218.16453-1-liupeibao@loongson.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 40e4eb324c ]
Shifting signed 32-bit value by 31 bits is undefined, so changing
significant bit to unsigned. The UBSAN warning calltrace like below:
UBSAN: shift-out-of-bounds in drivers/net/phy/mdio_bus.c:586:27
left shift of 1 by 31 places cannot be represented in type 'int'
Call Trace:
<TASK>
dump_stack_lvl+0x7d/0xa5
dump_stack+0x15/0x1b
ubsan_epilogue+0xe/0x4e
__ubsan_handle_shift_out_of_bounds+0x1e7/0x20c
__mdiobus_register+0x49d/0x4e0
fixed_mdio_bus_init+0xd8/0x12d
do_one_initcall+0x76/0x430
kernel_init_freeable+0x3b3/0x422
kernel_init+0x24/0x1e0
ret_from_fork+0x1f/0x30
</TASK>
Fixes: 4fd5f812c2 ("phylib: allow incremental scanning of an mii bus")
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20221031132645.168421-1-cuigaosheng1@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c9524d929 ]
Syzkaller reports a memory leak as follows:
====================================
BUG: memory leak
unreferenced object 0xffff88810d81ac00 (size 240):
[...]
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<ffffffff838733d9>] __alloc_skb+0x1f9/0x270 net/core/skbuff.c:418
[<ffffffff833f742f>] alloc_skb include/linux/skbuff.h:1257 [inline]
[<ffffffff833f742f>] bt_skb_alloc include/net/bluetooth/bluetooth.h:469 [inline]
[<ffffffff833f742f>] vhci_get_user drivers/bluetooth/hci_vhci.c:391 [inline]
[<ffffffff833f742f>] vhci_write+0x5f/0x230 drivers/bluetooth/hci_vhci.c:511
[<ffffffff815e398d>] call_write_iter include/linux/fs.h:2192 [inline]
[<ffffffff815e398d>] new_sync_write fs/read_write.c:491 [inline]
[<ffffffff815e398d>] vfs_write+0x42d/0x540 fs/read_write.c:578
[<ffffffff815e3cdd>] ksys_write+0x9d/0x160 fs/read_write.c:631
[<ffffffff845e0645>] do_syscall_x64 arch/x86/entry/common.c:50 [inline]
[<ffffffff845e0645>] do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
[<ffffffff84600087>] entry_SYSCALL_64_after_hwframe+0x63/0xcd
====================================
HCI core will uses hci_rx_work() to process frame, which is queued to
the hdev->rx_q tail in hci_recv_frame() by HCI driver.
Yet the problem is that, HCI core may not free the skb after handling
ACL data packets. To be more specific, when start fragment does not
contain the L2CAP length, HCI core just copies skb into conn->rx_skb and
finishes frame process in l2cap_recv_acldata(), without freeing the skb,
which triggers the above memory leak.
This patch solves it by releasing the relative skb, after processing
the above case in l2cap_recv_acldata().
Fixes: 4d7ea8ee90 ("Bluetooth: L2CAP: Fix handling fragmented length")
Link: https://lore.kernel.org/all/0000000000000d0b1905e6aaef64@google.com/
Reported-and-tested-by: syzbot+8f819e36e01022991cfa@syzkaller.appspotmail.com
Signed-off-by: Hawkins Jiawei <yin31149@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d0e2d0328 ]
When l2cap_recv_frame() is invoked to receive data, and the cid is
L2CAP_CID_A2MP, if the channel does not exist, it will create a channel.
However, after a channel is created, the hold operation of the channel
is not performed. In this case, the value of channel reference counting
is 1. As a result, after hci_error_reset() is triggered, l2cap_conn_del()
invokes the close hook function of A2MP to release the channel. Then
l2cap_chan_unlock(chan) will trigger UAF issue.
The process is as follows:
Receive data:
l2cap_data_channel()
a2mp_channel_create() --->channel ref is 2
l2cap_chan_put() --->channel ref is 1
Triger event:
hci_error_reset()
hci_dev_do_close()
...
l2cap_disconn_cfm()
l2cap_conn_del()
l2cap_chan_hold() --->channel ref is 2
l2cap_chan_del() --->channel ref is 1
a2mp_chan_close_cb() --->channel ref is 0, release channel
l2cap_chan_unlock() --->UAF of channel
The detailed Call Trace is as follows:
BUG: KASAN: use-after-free in __mutex_unlock_slowpath+0xa6/0x5e0
Read of size 8 at addr ffff8880160664b8 by task kworker/u11:1/7593
Workqueue: hci0 hci_error_reset
Call Trace:
<TASK>
dump_stack_lvl+0xcd/0x134
print_report.cold+0x2ba/0x719
kasan_report+0xb1/0x1e0
kasan_check_range+0x140/0x190
__mutex_unlock_slowpath+0xa6/0x5e0
l2cap_conn_del+0x404/0x7b0
l2cap_disconn_cfm+0x8c/0xc0
hci_conn_hash_flush+0x11f/0x260
hci_dev_close_sync+0x5f5/0x11f0
hci_dev_do_close+0x2d/0x70
hci_error_reset+0x9e/0x140
process_one_work+0x98a/0x1620
worker_thread+0x665/0x1080
kthread+0x2e4/0x3a0
ret_from_fork+0x1f/0x30
</TASK>
Allocated by task 7593:
kasan_save_stack+0x1e/0x40
__kasan_kmalloc+0xa9/0xd0
l2cap_chan_create+0x40/0x930
amp_mgr_create+0x96/0x990
a2mp_channel_create+0x7d/0x150
l2cap_recv_frame+0x51b8/0x9a70
l2cap_recv_acldata+0xaa3/0xc00
hci_rx_work+0x702/0x1220
process_one_work+0x98a/0x1620
worker_thread+0x665/0x1080
kthread+0x2e4/0x3a0
ret_from_fork+0x1f/0x30
Freed by task 7593:
kasan_save_stack+0x1e/0x40
kasan_set_track+0x21/0x30
kasan_set_free_info+0x20/0x30
____kasan_slab_free+0x167/0x1c0
slab_free_freelist_hook+0x89/0x1c0
kfree+0xe2/0x580
l2cap_chan_put+0x22a/0x2d0
l2cap_conn_del+0x3fc/0x7b0
l2cap_disconn_cfm+0x8c/0xc0
hci_conn_hash_flush+0x11f/0x260
hci_dev_close_sync+0x5f5/0x11f0
hci_dev_do_close+0x2d/0x70
hci_error_reset+0x9e/0x140
process_one_work+0x98a/0x1620
worker_thread+0x665/0x1080
kthread+0x2e4/0x3a0
ret_from_fork+0x1f/0x30
Last potentially related work creation:
kasan_save_stack+0x1e/0x40
__kasan_record_aux_stack+0xbe/0xd0
call_rcu+0x99/0x740
netlink_release+0xe6a/0x1cf0
__sock_release+0xcd/0x280
sock_close+0x18/0x20
__fput+0x27c/0xa90
task_work_run+0xdd/0x1a0
exit_to_user_mode_prepare+0x23c/0x250
syscall_exit_to_user_mode+0x19/0x50
do_syscall_64+0x42/0x80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Second to last potentially related work creation:
kasan_save_stack+0x1e/0x40
__kasan_record_aux_stack+0xbe/0xd0
call_rcu+0x99/0x740
netlink_release+0xe6a/0x1cf0
__sock_release+0xcd/0x280
sock_close+0x18/0x20
__fput+0x27c/0xa90
task_work_run+0xdd/0x1a0
exit_to_user_mode_prepare+0x23c/0x250
syscall_exit_to_user_mode+0x19/0x50
do_syscall_64+0x42/0x80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Fixes: d0be8347c6 ("Bluetooth: L2CAP: Fix use-after-free caused by l2cap_chan_put")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 160fbcf3bf ]
By using skb_put we ensure that skb->tail is set
correctly. Currently, skb->tail is always zero, which
leads to errors, such as the following page fault in
rfcomm_recv_frame:
BUG: unable to handle page fault for address: ffffed1021de29ff
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
RIP: 0010:rfcomm_run+0x831/0x4040 (net/bluetooth/rfcomm/core.c:1751)
Fixes: afd2daa26c ("Bluetooth: Add support for virtio transport driver")
Signed-off-by: Soenke Huster <soenke.huster@eknoes.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3aff8aaca4 ]
Fix the race condition between the following two flows that run in
parallel:
1. l2cap_reassemble_sdu -> chan->ops->recv (l2cap_sock_recv_cb) ->
__sock_queue_rcv_skb.
2. bt_sock_recvmsg -> skb_recv_datagram, skb_free_datagram.
An SKB can be queued by the first flow and immediately dequeued and
freed by the second flow, therefore the callers of l2cap_reassemble_sdu
can't use the SKB after that function returns. However, some places
continue accessing struct l2cap_ctrl that resides in the SKB's CB for a
short time after l2cap_reassemble_sdu returns, leading to a
use-after-free condition (the stack trace is below, line numbers for
kernel 5.19.8).
Fix it by keeping a local copy of struct l2cap_ctrl.
BUG: KASAN: use-after-free in l2cap_rx_state_recv (net/bluetooth/l2cap_core.c:6906) bluetooth
Read of size 1 at addr ffff88812025f2f0 by task kworker/u17:3/43169
Workqueue: hci0 hci_rx_work [bluetooth]
Call Trace:
<TASK>
dump_stack_lvl (lib/dump_stack.c:107 (discriminator 4))
print_report.cold (mm/kasan/report.c:314 mm/kasan/report.c:429)
? l2cap_rx_state_recv (net/bluetooth/l2cap_core.c:6906) bluetooth
kasan_report (mm/kasan/report.c:162 mm/kasan/report.c:493)
? l2cap_rx_state_recv (net/bluetooth/l2cap_core.c:6906) bluetooth
l2cap_rx_state_recv (net/bluetooth/l2cap_core.c:6906) bluetooth
l2cap_rx (net/bluetooth/l2cap_core.c:7236 net/bluetooth/l2cap_core.c:7271) bluetooth
ret_from_fork (arch/x86/entry/entry_64.S:306)
</TASK>
Allocated by task 43169:
kasan_save_stack (mm/kasan/common.c:39)
__kasan_slab_alloc (mm/kasan/common.c:45 mm/kasan/common.c:436 mm/kasan/common.c:469)
kmem_cache_alloc_node (mm/slab.h:750 mm/slub.c:3243 mm/slub.c:3293)
__alloc_skb (net/core/skbuff.c:414)
l2cap_recv_frag (./include/net/bluetooth/bluetooth.h:425 net/bluetooth/l2cap_core.c:8329) bluetooth
l2cap_recv_acldata (net/bluetooth/l2cap_core.c:8442) bluetooth
hci_rx_work (net/bluetooth/hci_core.c:3642 net/bluetooth/hci_core.c:3832) bluetooth
process_one_work (kernel/workqueue.c:2289)
worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2437)
kthread (kernel/kthread.c:376)
ret_from_fork (arch/x86/entry/entry_64.S:306)
Freed by task 27920:
kasan_save_stack (mm/kasan/common.c:39)
kasan_set_track (mm/kasan/common.c:45)
kasan_set_free_info (mm/kasan/generic.c:372)
____kasan_slab_free (mm/kasan/common.c:368 mm/kasan/common.c:328)
slab_free_freelist_hook (mm/slub.c:1780)
kmem_cache_free (mm/slub.c:3536 mm/slub.c:3553)
skb_free_datagram (./include/net/sock.h:1578 ./include/net/sock.h:1639 net/core/datagram.c:323)
bt_sock_recvmsg (net/bluetooth/af_bluetooth.c:295) bluetooth
l2cap_sock_recvmsg (net/bluetooth/l2cap_sock.c:1212) bluetooth
sock_read_iter (net/socket.c:1087)
new_sync_read (./include/linux/fs.h:2052 fs/read_write.c:401)
vfs_read (fs/read_write.c:482)
ksys_read (fs/read_write.c:620)
do_syscall_64 (arch/x86/entry/common.c:50 arch/x86/entry/common.c:80)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:120)
Link: https://lore.kernel.org/linux-bluetooth/CAKErNvoqga1WcmoR3-0875esY6TVWFQDandbVZncSiuGPBQXLA@mail.gmail.com/T/#u
Fixes: d2a7ac5d5d ("Bluetooth: Add the ERTM receive state machine")
Fixes: 4b51dae967 ("Bluetooth: Add streaming mode receive and incoming packet classifier")
Signed-off-by: Maxim Mikityanskiy <maxtram95@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 510841da1f ]
Daniel Xu reported that the hash:net,iface type of the ipset subsystem does
not limit adding the same network with different interfaces to a set, which
can lead to huge memory usage or allocation failure.
The quick reproducer is
$ ipset create ACL.IN.ALL_PERMIT hash:net,iface hashsize 1048576 timeout 0
$ for i in $(seq 0 100); do /sbin/ipset add ACL.IN.ALL_PERMIT 0.0.0.0/0,kaf_$i timeout 0 -exist; done
The backtrace when vmalloc fails:
[Tue Oct 25 00:13:08 2022] ipset: vmalloc error: size 1073741848, exceeds total pages
<...>
[Tue Oct 25 00:13:08 2022] Call Trace:
[Tue Oct 25 00:13:08 2022] <TASK>
[Tue Oct 25 00:13:08 2022] dump_stack_lvl+0x48/0x60
[Tue Oct 25 00:13:08 2022] warn_alloc+0x155/0x180
[Tue Oct 25 00:13:08 2022] __vmalloc_node_range+0x72a/0x760
[Tue Oct 25 00:13:08 2022] ? hash_netiface4_add+0x7c0/0xb20
[Tue Oct 25 00:13:08 2022] ? __kmalloc_large_node+0x4a/0x90
[Tue Oct 25 00:13:08 2022] kvmalloc_node+0xa6/0xd0
[Tue Oct 25 00:13:08 2022] ? hash_netiface4_resize+0x99/0x710
<...>
The fix is to enforce the limit documented in the ipset(8) manpage:
> The internal restriction of the hash:net,iface set type is that the same
> network prefix cannot be stored with more than 64 different interfaces
> in a single set.
Fixes: ccf0a4b7fc ("netfilter: ipset: Add bucketsize parameter to all hash types")
Reported-by: Daniel Xu <dxu@dxuuu.xyz>
Signed-off-by: Jozsef Kadlecsik <kadlec@netfilter.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d37de92b38 ]
In the test_no_shared_qgroup() and test_multiple_refs() qgroup self tests,
if we fail to add the tree ref, remove the extent item or remove the
extent ref, we are returning from the test function without freeing the
"old_roots" ulist that was allocated by the previous calls to
btrfs_find_all_roots(). Fix that by calling ulist_free() before returning.
Fixes: 442244c963 ("btrfs: qgroup: Switch self test to extent-oriented qgroup mechanism.")
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92876eec38 ]
During backref walking, at find_parent_nodes(), if we are dealing with a
data extent and we get an error while resolving the indirect backrefs, at
resolve_indirect_refs(), or in the while loop that iterates over the refs
in the direct refs rbtree, we end up leaking the inode lists attached to
the direct refs we have in the direct refs rbtree that were not yet added
to the refs ulist passed as argument to find_parent_nodes(). Since they
were not yet added to the refs ulist and prelim_release() does not free
the lists, on error the caller can only free the lists attached to the
refs that were added to the refs ulist, all the remaining refs get their
inode lists never freed, therefore leaking their memory.
Fix this by having prelim_release() always free any attached inode list
to each ref found in the rbtree, and have find_parent_nodes() set the
ref's inode list to NULL once it transfers ownership of the inode list
to a ref added to the refs ulist passed to find_parent_nodes().
Fixes: 86d5f99442 ("btrfs: convert prelimary reference tracking to use rbtrees")
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5614dc3a47 ]
During backref walking, at resolve_indirect_refs(), if we get an error
we jump to the 'out' label and call ulist_free() on the 'parents' ulist,
which frees all the elements in the ulist - however that does not free
any inode lists that may be attached to elements, through the 'aux' field
of a ulist node, so we end up leaking lists if we have any attached to
the unodes.
Fix this by calling free_leaf_list() instead of ulist_free() when we exit
from resolve_indirect_refs(). The static function free_leaf_list() is
moved up for this to be possible and it's slightly simplified by removing
unnecessary code.
Fixes: 3301958b7c ("Btrfs: add inodes before dropping the extent lock in find_all_leafs")
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf00f54260 ]
The class is set in mISDN_register_device(), but if device_add() returns
error, it will lead to delete a device without added, fix this by using
device_is_registered() to check if the device is registered.
Fixes: a900845e56 ("mISDN: Add support for Traverse Technologies NETJet PCI cards")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e7d1d4d9ac ]
Afer commit 1fa5ae857b ("driver core: get rid of struct device's
bus_id string array"), the name of device is allocated dynamically,
add put_device() to give up the reference, so that the name can be
freed in kobject_cleanup() when the refcount is 0.
Set device class before put_device() to avoid null release() function
WARN message in device_release().
Fixes: 1fa5ae857b ("driver core: get rid of struct device's bus_id string array")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e97c089d7a ]
The syzkaller reported an issue:
KASAN: null-ptr-deref in range [0x0000000000000380-0x0000000000000387]
CPU: 0 PID: 4069 Comm: kworker/0:15 Not tainted 6.0.0-syzkaller-02734-g0326074ff465 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/22/2022
Workqueue: rcu_gp srcu_invoke_callbacks
RIP: 0010:rose_send_frame+0x1dd/0x2f0 net/rose/rose_link.c:101
Call Trace:
<IRQ>
rose_transmit_clear_request+0x1d5/0x290 net/rose/rose_link.c:255
rose_rx_call_request+0x4c0/0x1bc0 net/rose/af_rose.c:1009
rose_loopback_timer+0x19e/0x590 net/rose/rose_loopback.c:111
call_timer_fn+0x1a0/0x6b0 kernel/time/timer.c:1474
expire_timers kernel/time/timer.c:1519 [inline]
__run_timers.part.0+0x674/0xa80 kernel/time/timer.c:1790
__run_timers kernel/time/timer.c:1768 [inline]
run_timer_softirq+0xb3/0x1d0 kernel/time/timer.c:1803
__do_softirq+0x1d0/0x9c8 kernel/softirq.c:571
[...]
</IRQ>
It triggers NULL pointer dereference when 'neigh->dev->dev_addr' is
called in the rose_send_frame(). It's the first occurrence of the
`neigh` is in rose_loopback_timer() as `rose_loopback_neigh', and
the 'dev' in 'rose_loopback_neigh' is initialized sa nullptr.
It had been fixed by commit 3b3fd068c5
("rose: Fix Null pointer dereference in rose_send_frame()") ever.
But it's introduced by commit 3c53cd65de
("rose: check NULL rose_loopback_neigh->loopback") again.
We fix it by add NULL check in rose_transmit_clear_request(). When
the 'dev' in 'neigh' is NULL, we don't reply the request and just
clear it.
syzkaller don't provide repro, and I provide a syz repro like:
r0 = syz_init_net_socket$bt_sco(0x1f, 0x5, 0x2)
ioctl$sock_inet_SIOCSIFFLAGS(r0, 0x8914, &(0x7f0000000180)={'rose0\x00', 0x201})
r1 = syz_init_net_socket$rose(0xb, 0x5, 0x0)
bind$rose(r1, &(0x7f00000000c0)=@full={0xb, @dev, @null, 0x0, [@null, @null, @netrom, @netrom, @default, @null]}, 0x40)
connect$rose(r1, &(0x7f0000000240)=@short={0xb, @dev={0xbb, 0xbb, 0xbb, 0x1, 0x0}, @remote={0xcc, 0xcc, 0xcc, 0xcc, 0xcc, 0xcc, 0x1}, 0x1, @netrom={0xbb, 0xbb, 0xbb, 0xbb, 0xbb, 0x0, 0x0}}, 0x1c)
Fixes: 3c53cd65de ("rose: check NULL rose_loopback_neigh->loopback")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5663ed63ad ]
During the initialization of ip_vs_app_net_init(), if file ip_vs_app
fails to be created, the initialization is successful by default.
Therefore, the ip_vs_app file doesn't be found during the remove in
ip_vs_app_net_cleanup(). It will cause WRNING.
The following is the stack information:
name 'ip_vs_app'
WARNING: CPU: 1 PID: 9 at fs/proc/generic.c:712 remove_proc_entry+0x389/0x460
Modules linked in:
Workqueue: netns cleanup_net
RIP: 0010:remove_proc_entry+0x389/0x460
Call Trace:
<TASK>
ops_exit_list+0x125/0x170
cleanup_net+0x4ea/0xb00
process_one_work+0x9bf/0x1710
worker_thread+0x665/0x1080
kthread+0x2e4/0x3a0
ret_from_fork+0x1f/0x30
</TASK>
Fixes: 457c4cbc5a ("[NET]: Make /proc/net per network namespace")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d00c6a0da ]
During the initialization of ip_vs_conn_net_init(), if file ip_vs_conn
or ip_vs_conn_sync fails to be created, the initialization is successful
by default. Therefore, the ip_vs_conn or ip_vs_conn_sync file doesn't
be found during the remove.
The following is the stack information:
name 'ip_vs_conn_sync'
WARNING: CPU: 3 PID: 9 at fs/proc/generic.c:712
remove_proc_entry+0x389/0x460
Modules linked in:
Workqueue: netns cleanup_net
RIP: 0010:remove_proc_entry+0x389/0x460
Call Trace:
<TASK>
__ip_vs_cleanup_batch+0x7d/0x120
ops_exit_list+0x125/0x170
cleanup_net+0x4ea/0xb00
process_one_work+0x9bf/0x1710
worker_thread+0x665/0x1080
kthread+0x2e4/0x3a0
ret_from_fork+0x1f/0x30
</TASK>
Fixes: 61b1ab4583 ("IPVS: netns, add basic init per netns.")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c26159c97 ]
The `char` type with no explicit sign is sometimes signed and sometimes
unsigned. This code will break on platforms such as arm, where char is
unsigned. So mark it here as explicitly signed, so that the
todrop_counter decrement and subsequent comparison is correct.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26b5934ff4 ]
No need to postpone this to the commit release path, since no packets
are walking over this object, this is accessed from control plane only.
This helped uncovered UAF triggered by races with the netlink notifier.
Fixes: 9dd732e0bd ("netfilter: nf_tables: memleak flow rule from commit path")
Reported-by: syzbot+8f747f62763bc6c32916@syzkaller.appspotmail.com
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d4bc8271db ]
commit release path is invoked via call_rcu and it runs lockless to
release the objects after rcu grace period. The netlink notifier handler
might win race to remove objects that the transaction context is still
referencing from the commit release path.
Call rcu_barrier() to ensure pending rcu callbacks run to completion
if the list of transactions to be destroyed is not empty.
Fixes: 6001a930ce ("netfilter: nftables: introduce table ownership")
Reported-by: syzbot+8f747f62763bc6c32916@syzkaller.appspotmail.com
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 363a5328f4 ]
Recently, we got two syzkaller problems because of oversize packet
when napi frags enabled.
One of the problems is because the first seg size of the iov_iter
from user space is very big, it is 2147479538 which is bigger than
the threshold value for bail out early in __alloc_pages(). And
skb->pfmemalloc is true, __kmalloc_reserve() would use pfmemalloc
reserves without __GFP_NOWARN flag. Thus we got a warning as following:
========================================================
WARNING: CPU: 1 PID: 17965 at mm/page_alloc.c:5295 __alloc_pages+0x1308/0x16c4 mm/page_alloc.c:5295
...
Call trace:
__alloc_pages+0x1308/0x16c4 mm/page_alloc.c:5295
__alloc_pages_node include/linux/gfp.h:550 [inline]
alloc_pages_node include/linux/gfp.h:564 [inline]
kmalloc_large_node+0x94/0x350 mm/slub.c:4038
__kmalloc_node_track_caller+0x620/0x8e4 mm/slub.c:4545
__kmalloc_reserve.constprop.0+0x1e4/0x2b0 net/core/skbuff.c:151
pskb_expand_head+0x130/0x8b0 net/core/skbuff.c:1654
__skb_grow include/linux/skbuff.h:2779 [inline]
tun_napi_alloc_frags+0x144/0x610 drivers/net/tun.c:1477
tun_get_user+0x31c/0x2010 drivers/net/tun.c:1835
tun_chr_write_iter+0x98/0x100 drivers/net/tun.c:2036
The other problem is because odd IPv6 packets without NEXTHDR_NONE
extension header and have big packet length, it is 2127925 which is
bigger than ETH_MAX_MTU(65535). After ipv6_gso_pull_exthdrs() in
ipv6_gro_receive(), network_header offset and transport_header offset
are all bigger than U16_MAX. That would trigger skb->network_header
and skb->transport_header overflow error, because they are all '__u16'
type. Eventually, it would affect the value for __skb_push(skb, value),
and make it be a big value. After __skb_push() in ipv6_gro_receive(),
skb->data would less than skb->head, an out of bounds memory bug occurred.
That would trigger the problem as following:
==================================================================
BUG: KASAN: use-after-free in eth_type_trans+0x100/0x260
...
Call trace:
dump_backtrace+0xd8/0x130
show_stack+0x1c/0x50
dump_stack_lvl+0x64/0x7c
print_address_description.constprop.0+0xbc/0x2e8
print_report+0x100/0x1e4
kasan_report+0x80/0x120
__asan_load8+0x78/0xa0
eth_type_trans+0x100/0x260
napi_gro_frags+0x164/0x550
tun_get_user+0xda4/0x1270
tun_chr_write_iter+0x74/0x130
do_iter_readv_writev+0x130/0x1ec
do_iter_write+0xbc/0x1e0
vfs_writev+0x13c/0x26c
To fix the problems, restrict the packet size less than
(ETH_MAX_MTU - NET_SKB_PAD - NET_IP_ALIGN) which has considered reserved
skb space in napi_alloc_skb() because transport_header is an offset from
skb->head. Add len check in tun_napi_alloc_frags() simply.
Fixes: 90e33d4594 ("tun: enable napi_gro_frags() for TUN/TAP driver")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20221029094101.1653855-1-william.xuanziyang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8bdc2acd42 ]
We can't use "skb" again after passing it to qdisc_enqueue(). This is
basically identical to commit 2f09707d0c ("sch_sfb: Also store skb
len before calling child enqueue").
Fixes: d7f4f332f0 ("sch_red: update backlog as well")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 171a93182e ]
Clang gives a warning when compiling pata_legacy.c with 'make W=1' about
the 'rt' local variable in pdc20230_set_piomode() being set but unused.
Quite obviously, there is an outb() call missing to write back the updated
variable. Moreover, checking the docs by Petr Soucek revealed that bitwise
AND should have been done with a negated timing mask and the master/slave
timing masks were swapped while updating...
Fixes: 669a5db411 ("[libata] Add a bunch of PATA drivers.")
Reported-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 06a4df5863 ]
The ndo_start_xmit() method must not free skb when returning
NETDEV_TX_BUSY, since caller is going to requeue freed skb.
Fix it by returning NETDEV_TX_OK in case of dma_map_single() fails.
Fixes: 79f339125e ("net: fec: Add software TSO support")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 93d904a734 ]
nfcmrvl_i2c_nci_send() will be called by nfcmrvl_nci_send(), and skb
should be freed in nfcmrvl_i2c_nci_send(). However, nfcmrvl_nci_send()
will only free skb when i2c_master_send() return >=0, which means skb
will memleak when i2c_master_send() failed. Free skb no matter whether
i2c_master_send() succeeds.
Fixes: b5b3e23e4c ("NFC: nfcmrvl: add i2c driver")
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a146b7e30 ]
s3fwrn5_nci_send() will call s3fwrn5_i2c_write() or s3fwrn82_uart_write(),
and free the skb if write() failed. However, even if the write() run
succeeds, the skb will not be freed in write(). As the result, the skb
will memleak. s3fwrn5_nci_send() should also free the skb when write()
succeeds.
Fixes: c04c674fad ("nfc: s3fwrn5: Add driver for Samsung S3FWRN5 NFC Chip")
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7bf1ed6aff ]
nxp_nci_send() will call nxp_nci_i2c_write(), and only free skb when
nxp_nci_i2c_write() failed. However, even if the nxp_nci_i2c_write()
run succeeds, the skb will not be freed in nxp_nci_i2c_write(). As the
result, the skb will memleak. nxp_nci_send() should also free the skb
when nxp_nci_i2c_write() succeeds.
Fixes: dece45855a ("NFC: nxp-nci: Add support for NXP NCI chips")
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e4aae6b8c ]
fdp_nci_send() will call fdp_nci_i2c_write that will not free skb in
the function. As a result, when fdp_nci_i2c_write() finished, the skb
will memleak. fdp_nci_send() should free skb after fdp_nci_i2c_write()
finished.
Fixes: a06347c04c ("NFC: Add Intel Fields Peak NFC solution driver")
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a2c65a9d05 ]
DSA tagging protocol drivers can be changed at runtime through sysfs and
at probe time through the device tree (support for the latter was added
later).
When changing through sysfs, it is assumed that the module for the new
tagging protocol was already loaded into the kernel (in fact this is
only a concern for Ocelot/Felix switches, where we have tag_ocelot.ko
and tag_ocelot_8021q.ko; for every other switch, the default and
alternative protocols are compiled within the same .ko, so there is
nothing for the user to load).
The kernel cannot currently call request_module(), because it has no way
of constructing the modalias name of the tagging protocol driver
("dsa_tag-%d", where the number is one of DSA_TAG_PROTO_*_VALUE).
The device tree only contains the string name of the tagging protocol
("ocelot-8021q"), and the only mapping between the string and the
DSA_TAG_PROTO_OCELOT_8021Q_VALUE is present in tag_ocelot_8021q.ko.
So this is a chicken-and-egg situation and dsa_core.ko has nothing based
on which it can automatically request the insertion of the module.
As a consequence, if CONFIG_NET_DSA_TAG_OCELOT_8021Q is built as module,
the switch will forever defer probing.
The long-term solution is to make DSA call request_module() somehow,
but that probably needs some refactoring.
What we can do to keep operating with existing device tree blobs is to
cancel the attempt to change the tagging protocol with the one specified
there, and to remain operating with the default one. Depending on the
situation, the default protocol might still allow some functionality
(in the case of ocelot, it does), and it's better to have that than to
fail to probe.
Fixes: deff710703 ("net: dsa: Allow default tag protocol to be overridden from DT")
Link: https://lore.kernel.org/lkml/20221027113248.420216-1-michael@walle.cc/
Reported-by: Heiko Thiery <heiko.thiery@gmail.com>
Reported-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221027145439.3086017-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 633efc8b3d ]
kmemleak reported memory leaks in dsa_loop_init():
kmemleak: 12 new suspected memory leaks
unreferenced object 0xffff8880138ce000 (size 2048):
comm "modprobe", pid 390, jiffies 4295040478 (age 238.976s)
backtrace:
[<000000006a94f1d5>] kmalloc_trace+0x26/0x60
[<00000000a9c44622>] phy_device_create+0x5d/0x970
[<00000000d0ee2afc>] get_phy_device+0xf3/0x2b0
[<00000000dca0c71f>] __fixed_phy_register.part.0+0x92/0x4e0
[<000000008a834798>] fixed_phy_register+0x84/0xb0
[<0000000055223fcb>] dsa_loop_init+0xa9/0x116 [dsa_loop]
...
There are two reasons for memleak in dsa_loop_init().
First, fixed_phy_register() create and register phy_device:
fixed_phy_register()
get_phy_device()
phy_device_create() # freed by phy_device_free()
phy_device_register() # freed by phy_device_remove()
But fixed_phy_unregister() only calls phy_device_remove().
So the memory allocated in phy_device_create() is leaked.
Second, when mdio_driver_register() fail in dsa_loop_init(),
it just returns and there is no cleanup for phydevs.
Fix the problems by catching the error of mdio_driver_register()
in dsa_loop_init(), then calling both fixed_phy_unregister() and
phy_device_free() to release phydevs.
Also add a function for phydevs cleanup to avoid duplacate.
Fixes: 98cd1552ea ("net: dsa: Mock-up driver")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 038efb6348 ]
When holding a delegation, the NFS client optimizes away setting the
attributes of a file from the GETATTR in the compound after CLONE, and for
a zero-length CLONE we will end up setting the inode's size to zero in
nfs42_copy_dest_done(). Handle this case by computing the resulting count
from the server's reported size after CLONE's GETATTR.
Suggested-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Fixes: 94d202d5ca ("NFSv42: Copy offload should update the file size when appropriate")
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cbdeaee94a ]
There is a null-ptr-deref when xps sysfs alloc failed:
BUG: KASAN: null-ptr-deref in sysfs_do_create_link_sd+0x40/0xd0
Read of size 8 at addr 0000000000000030 by task gssproxy/457
CPU: 5 PID: 457 Comm: gssproxy Not tainted 6.0.0-09040-g02357b27ee03 #9
Call Trace:
<TASK>
dump_stack_lvl+0x34/0x44
kasan_report+0xa3/0x120
sysfs_do_create_link_sd+0x40/0xd0
rpc_sysfs_client_setup+0x161/0x1b0
rpc_new_client+0x3fc/0x6e0
rpc_create_xprt+0x71/0x220
rpc_create+0x1d4/0x350
gssp_rpc_create+0xc3/0x160
set_gssp_clnt+0xbc/0x140
write_gssp+0x116/0x1a0
proc_reg_write+0xd6/0x130
vfs_write+0x177/0x690
ksys_write+0xb9/0x150
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
When the xprt_switch sysfs alloc failed, should not add xprt and
switch sysfs to it, otherwise, maybe null-ptr-deref; also initialize
the 'xps_sysfs' to NULL to avoid oops when destroy it.
Fixes: 2a338a5431 ("sunrpc: add a symlink from rpc-client directory to the xprt_switch")
Fixes: d408ebe04a ("sunrpc: add add sysfs directory per xprt under each xprt_switch")
Fixes: baea99445d ("sunrpc: add xprt_switch direcotry to sunrpc's sysfs")
Signed-off-by: Zhang Xiaoxu <zhangxiaoxu5@huawei.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e59679f2b7 ]
Currently, we are only guaranteed to send RECLAIM_COMPLETE if we have
open state to recover. Fix the client to always send RECLAIM_COMPLETE
after setting up the lease.
Fixes: fce5c838e1 ("nfs41: RECLAIM_COMPLETE functionality")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d917cba32 ]
If RECLAIM_COMPLETE sets the NFS4CLNT_BIND_CONN_TO_SESSION flag, then we
need to loop back in order to handle it.
Fixes: 0048fdd066 ("NFSv4.1: RECLAIM_COMPLETE must handle NFS4ERR_CONN_NOT_BOUND_TO_SESSION")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ba04394e0 ]
If the server reboots while we are engaged in a delegation return, and
there is a pNFS layout with return-on-close set, then the current code
can end up deadlocking in pnfs_roc() when nfs_inode_set_delegation()
tries to return the old delegation.
Now that delegreturn actually uses its own copy of the stateid, it
should be safe to just always update the delegation stateid in place.
Fixes: 078000d02d ("pNFS: We want return-on-close to complete when evicting the inode")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e272ed69a ]
When function reset and local invalidate are mixed, HNS RoCEE may hang.
Before introducing the cause of the problem, two hardware internal
concepts need to be introduced:
1. Execution queue: The queue of hardware execution instructions,
function reset and local invalidate are queued for execution in this
queue.
2.Local queue: A queue that stores local operation instructions. The
instructions in the local queue will be sent to the execution queue
for execution. The instructions in the local queue will not be removed
until the execution is completed.
The reason for the problem is as follows:
1. There is a function reset instruction in the execution queue, which
is currently being executed. A necessary condition for the successful
execution of function reset is: the hardware pipeline needs to empty
the instructions that were not completed before;
2. A local invalidate instruction at the head of the local queue is
sent to the execution queue. Now there are two instructions in the
execution queue, the first is the function reset instruction, and the
second is the local invalidate instruction, which will be executed in
se quence;
3. The user has issued many local invalidate operations, causing the
local queue to be filled up.
4. The user still has a new local operation command and is queuing to
enter the local queue. But the local queue is full and cannot receive
new instructions, this instruction is temporarily stored at the
hardware pipeline.
5. The function reset has been waiting for the instruction before the
hardware pipeline stage is drained. The hardware pipeline stage also
caches a local invalidate instruction, so the function reset cannot be
completed, and the instructions after it cannot be executed.
These factors together cause the execution logic deadlock of the hardware,
and the consequence is that RoCEE will not have any response. Considering
that the local operation command may potentially cause RoCEE to hang, this
feature is no longer supported.
Fixes: e93df01085 ("RDMA/hns: Support local invalidate for hip08 in kernel space")
Signed-off-by: Yangyang Li <liyangyang20@huawei.com>
Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: Haoyue Xu <xuhaoyue1@hisilicon.com>
Link: https://lore.kernel.org/r/20221024083814.1089722-2-xuhaoyue1@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1afac08b39 ]
Commit 13bac86195 ("IB/hfi1: Fix abba locking issue with sc_disable()")
incorrectly tries to move a list from one list head to another. The
result is a kernel crash.
The crash is triggered when a link goes down and there are waiters for a
send to complete. The following signature is seen:
BUG: kernel NULL pointer dereference, address: 0000000000000030
[...]
Call Trace:
sc_disable+0x1ba/0x240 [hfi1]
pio_freeze+0x3d/0x60 [hfi1]
handle_freeze+0x27/0x1b0 [hfi1]
process_one_work+0x1b0/0x380
? process_one_work+0x380/0x380
worker_thread+0x30/0x360
? process_one_work+0x380/0x380
kthread+0xd7/0x100
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x1f/0x30
The fix is to use the correct call to move the list.
Fixes: 13bac86195 ("IB/hfi1: Fix abba locking issue with sc_disable()")
Signed-off-by: Dean Luick <dean.luick@cornelisnetworks.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Link: https://lore.kernel.org/r/166610327042.674422.6146908799669288976.stgit@awfm-02.cornelisnetworks.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb83f502ad ]
Commit 27cfde795a ("RDMA/cma: Fix arguments order in net device
validation") swapped the src and dst addresses in the call to
validate_net_dev().
As a consequence, the test in validate_ipv4_net_dev() to see if the
net_dev is the right one, is incorrect for port 1 <-> 2 communication when
the ports are on the same sub-net. This is fixed by denoting the
flowi4_oif as the device instead of the incoming one.
The bug has not been observed using IPv6 addresses.
Fixes: 27cfde795a ("RDMA/cma: Fix arguments order in net device validation")
Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com>
Link: https://lore.kernel.org/r/20221012141542.16925-1-haakon.bugge@oracle.com
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1739c7017f ]
The KVM_X86_SET_MSR_FILTER ioctls contains a pointer in the passed in
struct which means it has a different struct size depending on whether
it gets called from 32bit or 64bit code.
This patch introduces compat code that converts from the 32bit struct to
its 64bit counterpart which then gets used going forward internally.
With this applied, 32bit QEMU can successfully set MSR bitmaps when
running on 64bit kernels.
Reported-by: Andrew Randrianasulu <randrianasulu@gmail.com>
Fixes: 1a155254ff ("KVM: x86: Introduce MSR filtering")
Signed-off-by: Alexander Graf <graf@amazon.com>
Message-Id: <20221017184541.2658-4-graf@amazon.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e3272bc17 ]
In the next patch we want to introduce a second caller to
set_msr_filter() which constructs its own filter list on the stack.
Refactor the original function so it takes it as argument instead of
reading it through copy_from_user().
Signed-off-by: Alexander Graf <graf@amazon.com>
Message-Id: <20221017184541.2658-3-graf@amazon.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf5029d5dd ]
The flags for KVM_CAP_X86_USER_SPACE_MSR and KVM_X86_SET_MSR_FILTER
have no protection for their unused bits. Without protection, future
development for these features will be difficult. Add the protection
needed to make it possible to extend these features in the future.
Signed-off-by: Aaron Lewis <aaronlewis@google.com>
Message-Id: <20220714161314.1715227-1-aaronlewis@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Stable-dep-of: 2e3272bc17 ("KVM: x86: Copy filter arg outside kvm_vm_ioctl_set_msr_filter()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fac35ba763 ]
On some architectures (like ARM64), it can support CONT-PTE/PMD size
hugetlb, which means it can support not only PMD/PUD size hugetlb (2M and
1G), but also CONT-PTE/PMD size(64K and 32M) if a 4K page size specified.
So when looking up a CONT-PTE size hugetlb page by follow_page(), it will
use pte_offset_map_lock() to get the pte entry lock for the CONT-PTE size
hugetlb in follow_page_pte(). However this pte entry lock is incorrect
for the CONT-PTE size hugetlb, since we should use huge_pte_lock() to get
the correct lock, which is mm->page_table_lock.
That means the pte entry of the CONT-PTE size hugetlb under current pte
lock is unstable in follow_page_pte(), we can continue to migrate or
poison the pte entry of the CONT-PTE size hugetlb, which can cause some
potential race issues, even though they are under the 'pte lock'.
For example, suppose thread A is trying to look up a CONT-PTE size hugetlb
page by move_pages() syscall under the lock, however antoher thread B can
migrate the CONT-PTE hugetlb page at the same time, which will cause
thread A to get an incorrect page, if thread A also wants to do page
migration, then data inconsistency error occurs.
Moreover we have the same issue for CONT-PMD size hugetlb in
follow_huge_pmd().
To fix above issues, rename the follow_huge_pmd() as follow_huge_pmd_pte()
to handle PMD and PTE level size hugetlb, which uses huge_pte_lock() to
get the correct pte entry lock to make the pte entry stable.
Mike said:
Support for CONT_PMD/_PTE was added with bb9dd3df8e ("arm64: hugetlb:
refactor find_num_contig()"). Patch series "Support for contiguous pte
hugepages", v4. However, I do not believe these code paths were
executed until migration support was added with 5480280d3f ("arm64/mm:
enable HugeTLB migration for contiguous bit HugeTLB pages") I would go
with 5480280d3f for the Fixes: targe.
Link: https://lkml.kernel.org/r/635f43bdd85ac2615a58405da82b4d33c6e5eb05.1662017562.git.baolin.wang@linux.alibaba.com
Fixes: 5480280d3f ("arm64/mm: enable HugeTLB migration for contiguous bit HugeTLB pages")
Signed-off-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Suggested-by: Mike Kravetz <mike.kravetz@oracle.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Muchun Song <songmuchun@bytedance.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5623f751bd ]
Add a dedicated "exception type" for #DBs, as #DBs can be fault-like or
trap-like depending the sub-type of #DB, and effectively defer the
decision of what to do with the #DB to the caller.
For the emulator's two calls to exception_type(), treat the #DB as
fault-like, as the emulator handles only code breakpoint and general
detect #DBs, both of which are fault-like.
For event injection, which uses exception_type() to determine whether to
set EFLAGS.RF=1 on the stack, keep the current behavior of not setting
RF=1 for #DBs. Intel and AMD explicitly state RF isn't set on code #DBs,
so exempting by failing the "== EXCPT_FAULT" check is correct. The only
other fault-like #DB is General Detect, and despite Intel and AMD both
strongly implying (through omission) that General Detect #DBs should set
RF=1, hardware (multiple generations of both Intel and AMD), in fact does
not. Through insider knowledge, extreme foresight, sheer dumb luck, or
some combination thereof, KVM correctly handled RF for General Detect #DBs.
Fixes: 38827dbd3f ("KVM: x86: Do not update EFLAGS on faulting emulation")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Link: https://lore.kernel.org/r/20220830231614.3580124-9-seanjc@google.com
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a61d7c5432 ]
Trace exceptions that are re-injected, not just those that KVM is
injecting for the first time. Debugging re-injection bugs is painful
enough as is, not having visibility into what KVM is doing only makes
things worse.
Delay propagating pending=>injected in the non-reinjection path so that
the tracing can properly identify reinjected exceptions.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Message-Id: <25470690a38b4d2b32b6204875dd35676c65c9f2.1651440202.git.maciej.szmigiero@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Stable-dep-of: 5623f751bd ("KVM: x86: Treat #DBs from the emulator as fault-like (code and DR7.GD=1)")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd269188ea ]
The kernel test robot reported the following sparse warning:
arch/arm64/include/asm/cmpxchg.h:88:1: sparse: sparse: cast truncates
bits from constant value (369 becomes 69)
On arm64, atomic_xchg only works on 8-bit byte fields. Thus, the macro
usage of LPFC_RXMONITOR_TABLE_IN_USE can be unintentionally truncated
leading to all logic involving the LPFC_RXMONITOR_TABLE_IN_USE macro to not
work properly.
Replace the Rx Table atomic_t indexing logic with a new
lpfc_rx_info_monitor structure that holds a circular ring buffer. For
locking semantics, a spinlock_t is used.
Link: https://lore.kernel.org/r/20220819011736.14141-4-jsmart2021@gmail.com
Fixes: 17b27ac592 ("scsi: lpfc: Add rx monitoring statistics")
Cc: <stable@vger.kernel.org> # v5.15+
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Whilst the codecs are restricted to 1920x1080 / 1080x1920, the ISP
isn't, but the limits advertised via V4L2 was 1920x1920 for all
roles.
Increase the limit to 16k x 16k for the ISP.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Whilst the adv7180 driver support s_routing, nothing else
does, and there is a missing lump of framework code to
define the mapping from connectors on a board to the inputs
they represent on the ADV7180.
Add a nasty hack to take a module parameter that is passed in
to s_routing on any call to G_STD, or S_STD (or subdev
g_input_status call).
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Add the parameters pins_40_41 and pins_40_45 to support other audio pin
options. Also, simplify the overlay using literal assignments.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
This is a second attempt to solve issue 5234, since it turns out that
the mcp980x driver only supports MCP9800-MCP9803. MCP9804, MCP9805 and
MCP9808 require the jc42 driver.
See: https://github.com/raspberrypi/linux/issues/5234
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
BCM54213PE is an Ethernet PHY that supports PTP hardware timestamping.
BCM54210PW ia another Ethernet PHY, but one without PTP support.
Unfortunately the two PHYs return the same ID when queried, so some
extra information is required to determine whether the PHY is PTP-
capable.
There are two Raspberry Pi products that use these PHYs - Pi 4B and
CM4 - and fortunately they use different PHY addresses, so use that as
a differentiator. Choose to treat a PHY with the same ID but another
address as a BCM54210PE, which seems more common.
See: https://github.com/raspberrypi/linux/issues/5104
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Following the clock rate range improvements to the clock framework,
trying to set a disjoint range on a clock will now result in an error.
Thus, we can't set a minimum rate higher than the maximum reported by
the firmware, or clk_set_min_rate() will fail.
Thus we need to clamp the rate we are about to ask for to the maximum
rate possible on that clock.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
At least the 4096x2160@60Hz mode requires some overclocking that isn't
available by default, even if hdmi_enable_4kp60 is enabled.
Let's add some logic to detect whether we can satisfy the core clock
requirements for that mode, and prevent it from being used otherwise.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
In order to support higher HDMI frequencies, users have to set the
hdmi_enable_4kp60 parameter in their config.txt file.
This will have the side-effect of raising the maximum of the core clock,
tied to the HVS, and managed by the HVS driver.
However, we are querying this in the HDMI driver by poking into the HVS
structure to get our struct clk handle.
Let's make this part of the HVS bind implementation to have all the core
clock related setup in the same place.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
In order to support higher HDMI frequencies, users have to set the
hdmi_enable_4kp60 parameter in their config.txt file.
We were detecting this so far by calling clk_round_rate() on the core
clock with the frequency we're supposed to run at when one of those
modes is enabled. Whether or not the parameter was enabled could then be
inferred by the returned rate since the maximum clock rate reported by
the firmware was one of the side effect of setting that parameter.
However, the recent clock rework we did changed what clk_round_rate()
was returning to always return the minimum allowed, and thus this test
wasn't reliable anymore.
Let's use the new clk_get_max_rate() function to reliably determine the
maximum rate allowed on that clock and fix the 4k@60Hz output.
Fixes: e9d6cea2af ("clk: bcm: rpi: Run some clocks at the minimum rate allowed")
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The firmware allows to query for its clocks the operating range of a
given clock. We'll need this for some drivers (KMS, in particular) to
infer the state of some configuration options, so let's create a
function to do so.
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
We'll need the clock IDs in more drivers than just the clock driver from
now on, so let's move them in the firmware header.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
A significant number of RaspberryPi drivers using the firmware don't
have a phandle to it, so end up scanning the device tree to find a node
with the firmware compatible.
That code is duplicated everywhere, so let's introduce a helper instead.
Link: https://lore.kernel.org/r/20220815-rpi-fix-4k-60-v4-1-a1b40526df3e@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
commit 7c7f9bc986 upstream.
When a UART port is newly registered, uart_configure_port() seeks to
deassert RS485 Transmit Enable by setting the RTS bit in port->mctrl.
However a number of UART drivers interpret a set RTS bit as *assertion*
instead of deassertion: Affected drivers include those using
serial8250_em485_config() (except 8250_bcm2835aux.c) and some using
mctrl_gpio (e.g. imx.c).
Since the interpretation of the RTS bit is driver-specific, it is not
suitable as a means to centrally deassert Transmit Enable in the serial
core. Instead, the serial core must call on drivers to deassert it in
their driver-specific way. One way to achieve that is to call
->rs485_config(). It implicitly deasserts Transmit Enable.
So amend uart_configure_port() and uart_resume_port() to invoke
uart_rs485_config(). That allows removing calls to uart_rs485_config()
from drivers' ->probe() hooks and declaring the function static.
Skip any invocation of ->set_mctrl() if RS485 is enabled. RS485 has no
hardware flow control, so the modem control lines are irrelevant and
need not be touched. When leaving RS485 mode, reset the modem control
lines to the state stored in port->mctrl. That way, UARTs which are
muxed between RS485 and RS232 transceivers drive the lines correctly
when switched to RS232. (serial8250_do_startup() historically raises
the OUT1 modem signal because otherwise interrupts are not signaled on
ancient PC UARTs, but I believe that no longer applies to modern,
RS485-capable UARTs and is thus safe to be skipped.)
imx.c modifies port->mctrl whenever Transmit Enable is asserted and
deasserted. Stop it from doing that so port->mctrl reflects the RS232
line state.
8250_omap.c deasserts Transmit Enable on ->runtime_resume() by calling
->set_mctrl(). Because that is now a no-op in RS485 mode, amend the
function to call serial8250_em485_stop_tx().
fsl_lpuart.c retrieves and applies the RS485 device tree properties
after registering the UART port. Because applying now happens on
registration in uart_configure_port(), move retrieval of the properties
ahead of uart_add_one_port().
Link: https://lore.kernel.org/all/20220329085050.311408-1-matthias.schiffer@ew.tq-group.com/
Link: https://lore.kernel.org/all/8f538a8903795f22f9acc94a9a31b03c9c4ccacb.camel@ginzinger.com/
Fixes: d3b3404df3 ("serial: Fix incorrect rs485 polarity on uart open")
Cc: stable@vger.kernel.org # v4.14+
Reported-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reported-by: Roosen Henri <Henri.Roosen@ginzinger.com>
Tested-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/2de36eba3fbe11278d5002e4e501afe0ceaca039.1663863805.git.lukas@wunner.de
Signed-off-by: Daisuke Mizobuchi <mizo@atmark-techno.com>
Signed-off-by: Dominique Martinet <dominique.martinet@atmark-techno.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0ed12afa56 upstream.
Several drivers that support setting the RS485 configuration via userspace
implement one or more of the following tasks:
- in case of an invalid RTS configuration (both RTS after send and RTS on
send set or both unset) fall back to enable RTS on send and disable RTS
after send
- nullify the padding field of the returned serial_rs485 struct
- copy the configuration into the uart port struct
- limit RTS delays to 100 ms
Move these tasks into the serial core to make them generic and to provide
a consistent behaviour among all drivers.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Link: https://lore.kernel.org/r/20220410104642.32195-2-LinoSanfilippo@gmx.de
Signed-off-by: Daisuke Mizobuchi <mizo@atmark-techno.com>
Signed-off-by: Dominique Martinet <dominique.martinet@atmark-techno.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 702de2c21e upstream.
We are seeing an IRQ storm on the global receive IRQ line under heavy
CAN bus load conditions with both CAN channels enabled.
Conditions:
The global receive IRQ line is shared between can0 and can1, either of
the channels can trigger interrupt while the other channel's IRQ line
is disabled (RFIE).
When global a receive IRQ interrupt occurs, we mask the interrupt in
the IRQ handler. Clearing and unmasking of the interrupt is happening
in rx_poll(). There is a race condition where rx_poll() unmasks the
interrupt, but the next IRQ handler does not mask the IRQ due to
NAPIF_STATE_MISSED flag (e.g.: can0 RX FIFO interrupt is disabled and
can1 is triggering RX interrupt, the delay in rx_poll() processing
results in setting NAPIF_STATE_MISSED flag) leading to an IRQ storm.
This patch fixes the issue by checking IRQ active and enabled before
handling the IRQ on a particular channel.
Fixes: dd3bd23eb4 ("can: rcar_canfd: Add Renesas R-Car CAN FD driver")
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/all/20221025155657.1426948-2-biju.das.jz@bp.renesas.com
Cc: stable@vger.kernel.org
[mkl: adjust commit message]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
[biju: removed gpriv from RCANFD_RFCC_RFIE macro]
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d887087c89 upstream.
RZ/G2L has separate channel specific IRQs for transmit and error
interrupts. But the IRQ handler processes both channels, even if there
no interrupt occurred on one of the channels.
This patch fixes the issue by passing a channel specific context
parameter instead of global one for the IRQ register and the IRQ
handler, it just handles the channel which is triggered the interrupt.
Fixes: 76e9353a80 ("can: rcar_canfd: Add support for RZ/G2L family")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/all/20221025155657.1426948-3-biju.das.jz@bp.renesas.com
Cc: stable@vger.kernel.org
[mkl: adjust commit message]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
[biju: fixed the conflicts manually]
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 84f7a9de06.
Because it introduces a problem that rq->__data_len is set to the wrong
value.
before the patch:
1) nr_bytes = rq->__data_len
2) rq->__data_len = sdp->sector_size
3) scsi_init_io()
4) rq->__data_len = nr_bytes
after the patch:
1) rq->__data_len = sdp->sector_size
2) scsi_init_io()
3) rq->__data_len = rq->__data_len -> __data_len is wrong
It will cause that io can only complete one segment each time, and the io
will requeue in scsi_io_completion_action(), which will cause severe
performance degradation.
Scsi write same is removed in commit e383e16e84 ("scsi: sd: Remove
WRITE_SAME support") from mainline, hence this patch is only needed for
stable kernels.
Fixes: 84f7a9de06 ("scsi: sd: Remove a local variable")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 84ce1ca3fe ]
Under memory pressure, enetc_refill_rx_ring() may fail, and when called
during the enetc_open() -> enetc_setup_rxbdr() procedure, this is not
checked for.
An extreme case of memory pressure will result in exactly zero buffers
being allocated for the RX ring, and in such a case it is expected that
hardware drops all RX packets due to lack of buffers.
This does not happen, because the reset-default value of the consumer
and produces index is 0, and this makes the ENETC think that all buffers
have been initialized and that it owns them (when in reality none were).
The hardware guide explains this best:
| Configure the receive ring producer index register RBaPIR with a value
| of 0. The producer index is initially configured by software but owned
| by hardware after the ring has been enabled. Hardware increments the
| index when a frame is received which may consume one or more BDs.
| Hardware is not allowed to increment the producer index to match the
| consumer index since it is used to indicate an empty condition. The ring
| can hold at most RBLENR[LENGTH]-1 received BDs.
|
| Configure the receive ring consumer index register RBaCIR. The
| consumer index is owned by software and updated during operation of the
| of the BD ring by software, to indicate that any receive data occupied
| in the BD has been processed and it has been prepared for new data.
| - If consumer index and producer index are initialized to the same
| value, it indicates that all BDs in the ring have been prepared and
| hardware owns all of the entries.
| - If consumer index is initialized to producer index plus N, it would
| indicate N BDs have been prepared. Note that hardware cannot start if
| only a single buffer is prepared due to the restrictions described in
| (2).
| - Software may write consumer index to match producer index anytime
| while the ring is operational to indicate all received BDs prior have
| been processed and new BDs prepared for hardware.
Normally, the value of rx_ring->rcir (consumer index) is brought in sync
with the rx_ring->next_to_use software index, but this only happens if
page allocation ever succeeded.
When PI==CI==0, the hardware appears to receive frames and write them to
DMA address 0x0 (?!), then set the READY bit in the BD.
The enetc_clean_rx_ring() function (and its XDP derivative) is naturally
not prepared to handle such a condition. It will attempt to process
those frames using the rx_swbd structure associated with index i of the
RX ring, but that structure is not fully initialized (enetc_new_page()
does all of that). So what happens next is undefined behavior.
To operate using no buffer, we must initialize the CI to PI + 1, which
will block the hardware from advancing the CI any further, and drop
everything.
The issue was seen while adding support for zero-copy AF_XDP sockets,
where buffer memory comes from user space, which can even decide to
supply no buffers at all (example: "xdpsock --txonly"). However, the bug
is present also with the network stack code, even though it would take a
very determined person to trigger a page allocation failure at the
perfect time (a series of ifup/ifdown under memory pressure should
eventually reproduce it given enough retries).
Fixes: d4fd0404c1 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20221027182925.3256653-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aefb62a998 ]
When setting Bluefield to DPU NIC mode using mlxconfig tool + sync
firmware reset flow, we run into scenario where the host was not
eswitch manager at the time of mlx5 driver load but becomes eswitch manager
after the sync firmware reset flow. This results in null pointer
access of mpfs structure during mac filter add. This change prevents null
pointer access but mpfs table entries will not be added.
Fixes: 5ec697446f ("net/mlx5: Add support for devlink reload action fw activate")
Signed-off-by: Suresh Devarakonda <ramad@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Bodong Wang <bodong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-12-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 416ef71363 ]
Update devlink health fw fatal reporter state to "healthy" is needed by
strictly calling devlink_health_reporter_state_update() after recovery
was done by PCI error handler. This is needed when fw_fatal reporter was
triggered due to PCI error. Poll health is called and set reporter state
to error. Health recovery failed (since EEH didn't re-enable the PCI).
PCI handlers keep on recover flow and succeed later without devlink
acknowledgment. Fix this by adding devlink state update at the end of
the PCI handler recovery process.
Fixes: 6181e5cb75 ("devlink: add support for reporter recovery completion")
Signed-off-by: Roy Novich <royno@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-11-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fad1783a6d ]
In case mlx5_pci_err_detected was called with state equals to
pci_channel_io_perm_failure, the driver will never come back up.
It is nice to know why the driver went to zombie land, so print some
useful information on pci err handlers.
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Stable-dep-of: 416ef71363 ("net/mlx5: Update fw fatal reporter state on PCI handlers successful recover")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 19b43a432e ]
When tx_port_ts is set, the driver diverts all UPD traffic over PTP port
to a dedicated PTP-SQ. The SKBs are cached until the wire-CQE arrives.
When the packet size is greater then MTU, the firmware might drop it and
the packet won't be transmitted to the wire, hence the wire-CQE won't
reach the driver. In this case the SKBs are accumulated in the SKB fifo.
Add room check to consider the PTP-SQ SKB fifo, when the SKB fifo is
full, driver stops the queue resulting in a TX timeout. Devlink
TX-reporter can recover from it.
Fixes: 1880bc4e4a ("net/mlx5e: Add TX port timestamp support")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-5-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 888be6b279 ]
An offloaded SA stops receiving after about 2^32 + replay_window
packets. For example, when SA reaches <seq-hi 0x1, seq 0x2c>, all
subsequent packets get dropped with SA-icv-failure (integrity_failed).
To reproduce the bug:
- ConnectX-6 Dx with crypto enabled (FW 22.30.1004)
- ipsec.conf:
nic-offload = yes
replay-window = 32
esn = yes
salifetime=24h
- Run netperf for a long time to send more than 2^32 packets
netperf -H <device-under-test> -t TCP_STREAM -l 20000
When 2^32 + replay_window packets are received, the replay window
moves from the 2nd half of subspace (overlap=1) to the 1st half
(overlap=0). The driver then updates the 'esn' value in NIC
(i.e. seq_hi) as follows.
seq_hi = xfrm_replay_seqhi(seq_bottom)
new esn in NIC = seq_hi + 1
The +1 increment is wrong, as seq_hi already contains the correct
seq_hi. For example, when seq_hi=1, the driver actually tells NIC to
use seq_hi=2 (esn). This incorrect esn value causes all subsequent
packets to fail integrity checks (SA-icv-failure). So, do not
increment.
Fixes: cb01008390 ("net/mlx5: IPSec, Add support for ESN")
Signed-off-by: Hyong Youb Kim <hyonkim@cisco.com>
Acked-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-2-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6aa8d0ce2 ]
Remove dir in nsim_dev_debugfs_init() when creating ports dir failed.
Otherwise, the netdevsim device will not be created next time. Kernel
reports an error: debugfs: Directory 'netdevsim1' with parent 'netdevsim'
already present!
Fixes: ab1d0cc004 ("netdevsim: change debugfs tree topology")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd954cc191 ]
As noted by Paolo Abeni, pr_warn doesn't generate any splat and can still
preserve the warning to the user that feature downgrade occurred. We
likely cannot introduce other kinds of checks / enforcement here because
syzbot can generate different genl versions to the datapath.
Reported-by: syzbot+31cde0bef4bbf8ba2d86@syzkaller.appspotmail.com
Fixes: 44da5ae5fb ("openvswitch: Drop user features if old user space attempted to create datapath")
Cc: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Aaron Conole <aconole@redhat.com>
Acked-by: Ilya Maximets <i.maximets@ovn.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f1fae475f1 ]
i2sbus_add_dev() is supposed to return the number of probed devices,
i.e. either 1 or 0. However, i2sbus_add_dev() has one error handling
that returns -ENODEV; this will screw up the accumulation number
counted in the caller, i2sbus_probe().
Fix the return value to 0 and add the comment for better understanding
for readers.
Fixes: f3d9478b2c ("[ALSA] snd-aoa: add snd-aoa")
Link: https://lore.kernel.org/r/20221027065233.13292-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a4c8482e3 ]
dev_set_name() in soundbus_add_one() allocates memory for name, it need be
freed when of_device_register() fails, call soundbus_dev_put() to give up
the reference that hold in device_initialize(), so that it can be freed in
kobject_cleanup() when the refcount hit to 0. And other resources are also
freed in i2sbus_release_dev(), so it can return 0 directly.
Fixes: f3d9478b2c ("[ALSA] snd-aoa: add snd-aoa")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221027013438.991920-1-yangyingliang@huawei.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e2badb4bd3 ]
The phylib callback is called after MAC driver's own resume callback is
called. For AVE driver, after resuming immediately, PHY state machine is
in PHY_NOLINK because there is a time lag from link-down to link-up due to
autoneg. The result is WARN_ON() dump in mdio_bus_phy_resume().
Since ave_resume() itself calls phy_resume(), AVE driver should manage
PHY PM. To indicate that MAC driver manages PHY PM, set
phydev->mac_managed_pm to true to avoid the unnecessary phylib call and
add missing phy_init_hw() to ave_resume().
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Fixes: fba863b816 ("net: phy: make PHY PM ops a no-op if MAC driver manages PHY PM")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20221024072227.24769-1-hayashi.kunihiko@socionext.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a8b43b12d ]
Using 'ethtool -d […]' on an i.MX6UL leads to a kernel crash:
Unhandled fault: external abort on non-linefetch (0x1008) at […]
due to this SoC has less registers in its FEC implementation compared to other
i.MX6 variants. Thus, a run-time decision is required to avoid access to
non-existing registers.
Fixes: a51d3ab507 ("net: fec: use a more proper compatible string for i.MX6UL type device")
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20221024080552.21004-1-jbe@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e0c57a5c70 ]
Platforms can provide the information about the availability of each
idle states via status flag. Platforms may have to disable one or more
idle states for various reasons like broken firmware or other unmet
dependencies.
Fix handling of such unavailable/disabled idle states by ignoring them
while parsing the states.
Fixes: a3381e3a65 ("PM / domains: Fix up domain-idle-states OF parsing")
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 52424f974b ]
When a reset was triggered on one VF with i40e_reset_vf
global PF state __I40E_VF_DISABLE was set on a PF until
the reset finished. If immediately after triggering reset
on one VF there is a request to reset on another
it will cause a hang on VF side because VF will be notified
of incoming reset but the reset will never happen because
of this global state, we will get such error message:
[ +4.890195] iavf 0000:86:02.1: Never saw reset
and VF will hang waiting for the reset to be triggered.
Fix this by introducing new VF state I40E_VF_STATE_RESETTING
that will be set on a VF if it is currently resetting instead of
the global __I40E_VF_DISABLE PF state.
Fixes: 3ba9bcb4b6 ("i40e: add locking around VF reset")
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20221024100526.1874914-2-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 54b5af5a43 ]
When enabling flow type for RSS hash via ethtool:
ethtool -N $pf rx-flow-hash tcp4|tcp6|udp4|udp6 s|d
the driver would fail to setup this setting on X722
device since it was using the mask on the register
dedicated for X710 devices.
Apply a different mask on the register when setting the
RSS hash for the X722 device.
When displaying the flow types enabled via ethtool:
ethtool -n $pf rx-flow-hash tcp4|tcp6|udp4|udp6
the driver would print wrong values for X722 device.
Fix this issue by testing masks for X722 device in
i40e_get_rss_hash_opts function.
Fixes: eb0dd6e4a3 ("i40e: Allow RSS Hash set with less than four parameters")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Michal Jaron <michalx.jaron@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20221024100526.1874914-1-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b92dd11725 ]
Testcase stat_all_metrics.sh fails in powerpc:
90: perf all metrics test : FAILED!
The testcase "stat_all_metrics.sh" verifies perf stat result for all the
metric events present in perf list. It runs perf metric events with
various commands and expects non-empty metric result.
Incase of powerpc:hv-24x7 events, some of the event count can be 0 based
on system configuration. And if that event used as denominator in divide
equation, it can cause divide by 0 error. The current nest_metric.json
file creating divide by 0 issue for some of the metric events, which
results in failure of the "stat_all_metrics.sh" test case.
Most of the metrics events have cycles or an event which expect to have
a larger value as denominator, so adding 1 to the denominator of the
metric expression as a fix.
Result in powerpc box after this patch changes:
90: perf all metrics test : Ok
Fixes: a3cbcadfdf ("perf vendor events power10: Adds 24x7 nest metric events for power10 platform")
Signed-off-by: Kajol Jain <kjain@linux.ibm.com>
Reviewed-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Cc: Athira Jajeev <atrajeev@linux.vnet.ibm.com>
Cc: Disha Goel <disgoel@linux.vnet.ibm.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kajol Jain <kjain@linux.ibm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nageswara R Sastry <rnsastry@linux.ibm.com>
Link: https://lore.kernel.org/r/20221014140220.122251-1-kjain@linux.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69d78a80da ]
If node_types does not have video/vbi/meta inputs or outputs,
then set num_inputs/num_outputs to 0 instead of 1.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 0c90f649d2 (media: vivid: add vivid_create_queue() helper)
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8da7f0976b ]
If it is a progressive (non-interlaced) format, then ignore the
interlaced timing values.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 7f68127fa1 ([media] videodev2.h: defines to calculate blanking and frame sizes)
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1f65ea411c ]
Whenever the compose width/height values change, the dev->bitmap_cap
vmalloc'ed array must be freed and dev->bitmap_cap set to NULL.
This was done in some places, but not all. This is only an issue if
overlay support is enabled and the bitmap clipping is used.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: ef834f7836 ([media] vivid: add the video capture and output parts)
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f8bcaf714a ]
VIDIOC_S_FBUF is by definition a scary ioctl, which is why only root
can use it. But at least check if the framebuffer parameters match that
of one of the framebuffer created by vivid, and reject anything else.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: ef834f7836 ([media] vivid: add the video capture and output parts)
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 85850af4fc ]
Hybrid sleep is currently hardcoded to only operate with S3 even
on systems that might not support it.
Instead of assuming this mode is what the user wants to use, for
hybrid sleep follow the setting of `mem_sleep_current` which
will respect mem_sleep_default kernel command line and policy
decisions made by the presence of the FADT low power idle bit.
Fixes: 81d45bdf89 ("PM / hibernate: Untangle power_down()")
Reported-and-tested-by: kolAflash <kolAflash@kolahilft.de>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216574
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 90bfee142a ]
If the number of pages from the userptr BO differs from the SG BO then the
allocated memory for the SG table doesn't get freed before returning
-EINVAL, which may lead to a memory leak in some error paths. Fix this by
checking the number of pages before allocating memory for the SG table.
Fixes: 264fb4d332 ("drm/amdgpu: Add multi-GPU DMA mapping helpers")
Signed-off-by: Rafael Mendonca <rafaelmendsr@gmail.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 720ca52bce ]
As Shakeel explains the commit under Fixes had the unintended
side-effect of no longer pre-loading the cached memory allowance.
Even tho we previously dropped the first packet received when
over memory limit - the consecutive ones would get thru by using
the cache. The charging was happening in batches of 128kB, so
we'd let in 128kB (truesize) worth of packets per one drop.
After the change we no longer force charge, there will be no
cache filling side effects. This causes significant drops and
connection stalls for workloads which use a lot of page cache,
since we can't reclaim page cache under GFP_NOWAIT.
Some of the latency can be recovered by improving SACK reneg
handling but nowhere near enough to get back to the pre-5.15
performance (the application I'm experimenting with still
sees 5-10x worst latency).
Apply the suggested workaround of using GFP_ATOMIC. We will now
be more permissive than previously as we'll drop _no_ packets
in softirq when under pressure. But I can't think of any good
and simple way to address that within networking.
Link: https://lore.kernel.org/all/20221012163300.795e7b86@kernel.org/
Suggested-by: Shakeel Butt <shakeelb@google.com>
Fixes: 4b1327be9f ("net-memcg: pass in gfp_t mask to mem_cgroup_charge_skmem()")
Acked-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Roman Gushchin <roman.gushchin@linux.dev>
Link: https://lore.kernel.org/r/20221021160304.1362511-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d2af9cce3 ]
This commit fixes a bug that can cause a TCP data sender to repeatedly
defer RTOs when encountering SACK reneging.
The bug is that when we're in fast recovery in a scenario with SACK
reneging, every time we get an ACK we call tcp_check_sack_reneging()
and it can note the apparent SACK reneging and rearm the RTO timer for
srtt/2 into the future. In some SACK reneging scenarios that can
happen repeatedly until the receive window fills up, at which point
the sender can't send any more, the ACKs stop arriving, and the RTO
fires at srtt/2 after the last ACK. But that can take far too long
(O(10 secs)), since the connection is stuck in fast recovery with a
low cwnd that cannot grow beyond ssthresh, even if more bandwidth is
available.
This fix changes the logic in tcp_check_sack_reneging() to only rearm
the RTO timer if data is cumulatively ACKed, indicating forward
progress. This avoids this kind of nearly infinite loop of RTO timer
re-arming. In addition, this meets the goals of
tcp_check_sack_reneging() in handling Windows TCP behavior that looks
temporarily like SACK reneging but is not really.
Many thanks to Jakub Kicinski and Neil Spring, who reported this issue
and provided critical packet traces that enabled root-causing this
issue. Also, many thanks to Jakub Kicinski for testing this fix.
Fixes: 5ae344c949 ("tcp: reduce spurious retransmits due to transient SACK reneging")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Reported-by: Neil Spring <ntspring@fb.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Tested-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20221021170821.1093930-1-ncardwell.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec791d8149 ]
The type of sk_rcvbuf and sk_sndbuf in struct sock is int, and
in tcp_add_backlog(), the variable limit is caculated by adding
sk_rcvbuf, sk_sndbuf and 64 * 1024, it may exceed the max value
of int and overflow. This patch reduces the limit budget by
halving the sndbuf to solve this issue since ACK packets are much
smaller than the payload.
Fixes: c9c3321257 ("tcp: add tcp_add_backlog()")
Signed-off-by: Lu Wei <luwei32@huawei.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d519f35096 ]
If packet is going to be coalesced, sk_sndbuf/sk_rcvbuf values
are not used. Defer their access to the point we need them.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: ec791d8149 ("tcp: fix a signed-integer-overflow bug in tcp_add_backlog()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c1eaa27ec ]
The ndo_start_xmit() method must not free skb when returning
NETDEV_TX_BUSY, since caller is going to requeue freed skb.
Fixes: 504d4721ee ("MIPS: Lantiq: Add ethernet driver")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d266935ac4 ]
When the ops_init() interface is invoked to initialize the net, but
ops->init() fails, data is released. However, the ptr pointer in
net->gen is invalid. In this case, when nfqnl_nf_hook_drop() is invoked
to release the net, invalid address access occurs.
The process is as follows:
setup_net()
ops_init()
data = kzalloc(...) ---> alloc "data"
net_assign_generic() ---> assign "date" to ptr in net->gen
...
ops->init() ---> failed
...
kfree(data); ---> ptr in net->gen is invalid
...
ops_exit_list()
...
nfqnl_nf_hook_drop()
*q = nfnl_queue_pernet(net) ---> q is invalid
The following is the Call Trace information:
BUG: KASAN: use-after-free in nfqnl_nf_hook_drop+0x264/0x280
Read of size 8 at addr ffff88810396b240 by task ip/15855
Call Trace:
<TASK>
dump_stack_lvl+0x8e/0xd1
print_report+0x155/0x454
kasan_report+0xba/0x1f0
nfqnl_nf_hook_drop+0x264/0x280
nf_queue_nf_hook_drop+0x8b/0x1b0
__nf_unregister_net_hook+0x1ae/0x5a0
nf_unregister_net_hooks+0xde/0x130
ops_exit_list+0xb0/0x170
setup_net+0x7ac/0xbd0
copy_net_ns+0x2e6/0x6b0
create_new_namespaces+0x382/0xa50
unshare_nsproxy_namespaces+0xa6/0x1c0
ksys_unshare+0x3a4/0x7e0
__x64_sys_unshare+0x2d/0x40
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
</TASK>
Allocated by task 15855:
kasan_save_stack+0x1e/0x40
kasan_set_track+0x21/0x30
__kasan_kmalloc+0xa1/0xb0
__kmalloc+0x49/0xb0
ops_init+0xe7/0x410
setup_net+0x5aa/0xbd0
copy_net_ns+0x2e6/0x6b0
create_new_namespaces+0x382/0xa50
unshare_nsproxy_namespaces+0xa6/0x1c0
ksys_unshare+0x3a4/0x7e0
__x64_sys_unshare+0x2d/0x40
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
Freed by task 15855:
kasan_save_stack+0x1e/0x40
kasan_set_track+0x21/0x30
kasan_save_free_info+0x2a/0x40
____kasan_slab_free+0x155/0x1b0
slab_free_freelist_hook+0x11b/0x220
__kmem_cache_free+0xa4/0x360
ops_init+0xb9/0x410
setup_net+0x5aa/0xbd0
copy_net_ns+0x2e6/0x6b0
create_new_namespaces+0x382/0xa50
unshare_nsproxy_namespaces+0xa6/0x1c0
ksys_unshare+0x3a4/0x7e0
__x64_sys_unshare+0x2d/0x40
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
Fixes: f875bae065 ("net: Automatically allocate per namespace data.")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6960d133f6 ]
NIC is stopped with rtnl_lock held, and during the stop it cancels the
'service_task' work and free irqs.
However, if CONFIG_MACSEC is set, rtnl_lock is acquired both from
aq_nic_service_task and aq_linkstate_threaded_isr. Then a deadlock
happens if aq_nic_stop tries to cancel/disable them when they've already
started their execution.
As the deadlock is caused by rtnl_lock, it causes many other processes
to stall, not only atlantic related stuff.
Fix it by introducing a mutex that protects each NIC's macsec related
data, and locking it instead of the rtnl_lock from the service task and
the threaded IRQ.
Before this patch, all macsec data was protected with rtnl_lock, but
maybe not all of it needs to be protected. With this new mutex, further
efforts can be made to limit the protected data only to that which
requires it. However, probably it doesn't worth it because all macsec's
data accesses are infrequent, and almost all are done from macsec_ops
or ethtool callbacks, called holding rtnl_lock, so macsec_mutex won't
never be much contended.
The issue appeared repeteadly attaching and deattaching the NIC to a
bond interface. Doing that after this patch I cannot reproduce the bug.
Fixes: 62c1c2e606 ("net: atlantic: MACSec offload skeleton")
Reported-by: Li Liang <liali@redhat.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Reviewed-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 170a9e341a ]
The offset 12 (bit-rate) of EEPROM SFP DAC (passive) cables is expected
to be in the range 0x64 to 0x68. However, the 5 meter and 7 meter Molex
passive cables have the rate ceiling 0x78 at offset 12.
Add a quirk for Molex passive cables to extend the rate ceiling to 0x78.
Fixes: abf0a1c2b2 ("amd-xgbe: Add support for SFP+ modules")
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09c5f6bf11 ]
The current XGBE code assumes that offset 6 of EEPROM SFP DAC (passive)
cables is NULL. However, some cables (the 5 meter and 7 meter Molex
passive cables) have non-zero data at offset 6. Fix the logic by moving
the passive cable check above the active checks, so as not to be
improperly identified as an active cable. This will fix the issue for
any passive cable that advertises 1000Base-CX in offset 6.
Fixes: abf0a1c2b2 ("amd-xgbe: Add support for SFP+ modules")
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 230db82413 ]
When a console stack dump is initiated with CONFIG_GCOV_PROFILE_ALL
enabled, show_trace_log_lvl() gets out of sync with the ORC unwinder,
causing the stack trace to show all text addresses as unreliable:
# echo l > /proc/sysrq-trigger
[ 477.521031] sysrq: Show backtrace of all active CPUs
[ 477.523813] NMI backtrace for cpu 0
[ 477.524492] CPU: 0 PID: 1021 Comm: bash Not tainted 6.0.0 #65
[ 477.525295] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.0-1.fc36 04/01/2014
[ 477.526439] Call Trace:
[ 477.526854] <TASK>
[ 477.527216] ? dump_stack_lvl+0xc7/0x114
[ 477.527801] ? dump_stack+0x13/0x1f
[ 477.528331] ? nmi_cpu_backtrace.cold+0xb5/0x10d
[ 477.528998] ? lapic_can_unplug_cpu+0xa0/0xa0
[ 477.529641] ? nmi_trigger_cpumask_backtrace+0x16a/0x1f0
[ 477.530393] ? arch_trigger_cpumask_backtrace+0x1d/0x30
[ 477.531136] ? sysrq_handle_showallcpus+0x1b/0x30
[ 477.531818] ? __handle_sysrq.cold+0x4e/0x1ae
[ 477.532451] ? write_sysrq_trigger+0x63/0x80
[ 477.533080] ? proc_reg_write+0x92/0x110
[ 477.533663] ? vfs_write+0x174/0x530
[ 477.534265] ? handle_mm_fault+0x16f/0x500
[ 477.534940] ? ksys_write+0x7b/0x170
[ 477.535543] ? __x64_sys_write+0x1d/0x30
[ 477.536191] ? do_syscall_64+0x6b/0x100
[ 477.536809] ? entry_SYSCALL_64_after_hwframe+0x63/0xcd
[ 477.537609] </TASK>
This happens when the compiled code for show_stack() has a single word
on the stack, and doesn't use a tail call to show_stack_log_lvl().
(CONFIG_GCOV_PROFILE_ALL=y is the only known case of this.) Then the
__unwind_start() skip logic hits an off-by-one bug and fails to unwind
all the way to the intended starting frame.
Fix it by reverting the following commit:
f1d9a2abff ("x86/unwind/orc: Don't skip the first frame for inactive tasks")
The original justification for that commit no longer exists. That
original issue was later fixed in a different way, with the following
commit:
f2ac57a4c4 ("x86/unwind/orc: Fix inactive tasks with stack pointer in %sp on GCC 10 compiled kernels")
Fixes: f1d9a2abff ("x86/unwind/orc: Don't skip the first frame for inactive tasks")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
[jpoimboe: rewrite commit log]
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15a9dbec63 ]
The `macb_resume`/`macb_suspend` methods already call the
`phylink_start`/`phylink_stop` methods during their execution so
explicitly say that the PM of the PHY is done by MAC by using the
`mac_managed_pm` flag of the `struct phylink_config`.
This also fixes the warning message issued during resume:
WARNING: CPU: 0 PID: 237 at drivers/net/phy/phy_device.c:323 mdio_bus_phy_resume+0x144/0x148
Depends-on: 96de900ae7 ("net: phylink: add mac_managed_pm in phylink_config structure")
Fixes: 744d23c71a ("net: phy: Warn about incorrect mdio_bus_phy_resume() state")
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20221019120929.63098-1-sergiu.moga@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ec2f4c6b2 ]
In hinic_vf_func_init(), if VF fails to register information with PF
through the MBOX, the MBOX callback function of VF is released once. But
it is released again in hinic_init_hwdev(). Remove one.
Fixes: 7dd29ee128 ("hinic: add sriov feature support")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 363cc87767 ]
When hinic_set_cmdq_depth() fails in hinic_init_cmdqs(), the cmdq memory is
not released correctly. Fix it.
Fixes: 72ef908bb3 ("hinic: add three net_device_ops of vf")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4c1f602df8 ]
When the input parameter idx meets the expected case option in
hinic_dbg_get_func_table(), read_data is not released. Fix it.
Fixes: 5215e16244 ("hinic: add support to query function table")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c0605cd675 ]
The value of lli_credit_cnt is incorrectly assigned, fix it.
Fixes: a0337c0dee ("hinic: add support to set and get irq coalesce")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9442358968 ]
If phy_device_register() fails, phy_device_free() need be called to
put refcount, so memory of phy device and device name can be freed
in callback function.
If get_phy_device() fails, mdiobus_unregister() need be called,
or it will cause warning in mdiobus_free() and kobject is leaked.
Fixes: 533dd11a12 ("net: socionext: Add Synquacer NetSec driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221019064104.3228892-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 82cb4e4612 ]
syzbot found a crash in tipc_topsrv_accept:
KASAN: null-ptr-deref in range [0x0000000000000008-0x000000000000000f]
Workqueue: tipc_rcv tipc_topsrv_accept
RIP: 0010:kernel_accept+0x22d/0x350 net/socket.c:3487
Call Trace:
<TASK>
tipc_topsrv_accept+0x197/0x280 net/tipc/topsrv.c:460
process_one_work+0x991/0x1610 kernel/workqueue.c:2289
worker_thread+0x665/0x1080 kernel/workqueue.c:2436
kthread+0x2e4/0x3a0 kernel/kthread.c:376
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:306
It was caused by srv->listener that might be set to null by
tipc_topsrv_stop() in net .exit whereas it's still used in
tipc_topsrv_accept() worker.
srv->listener is protected by srv->idr_lock in tipc_topsrv_stop(), so add
a check for srv->listener under srv->idr_lock in tipc_topsrv_accept() to
avoid the null-ptr-deref. To ensure the lsock is not released during the
tipc_topsrv_accept(), move sock_release() after tipc_topsrv_work_stop()
where it's waiting until the tipc_topsrv_accept worker to be done.
Note that sk_callback_lock is used to protect sk->sk_user_data instead of
srv->listener, and it should check srv in tipc_topsrv_listener_data_ready()
instead. This also ensures that no more tipc_topsrv_accept worker will be
started after tipc_conn_close() is called in tipc_topsrv_stop() where it
sets sk->sk_user_data to null.
Fixes: 0ef897be12 ("tipc: separate topology server listener socket from subcsriber sockets")
Reported-by: syzbot+c5ce866a8d30f4be0651@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Link: https://lore.kernel.org/r/4eee264380c409c61c6451af1059b7fb271a7e7b.1666120790.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c44f15c1c0 ]
Add 'volatile' to iounmap()'s argument to prevent build warnings.
This make it the same as other major architectures.
Placates these warnings: (12 such warnings)
../drivers/video/fbdev/riva/fbdev.c: In function 'rivafb_probe':
../drivers/video/fbdev/riva/fbdev.c:2067:42: error: passing argument 1 of 'iounmap' discards 'volatile' qualifier from pointer target type [-Werror=discarded-qualifiers]
2067 | iounmap(default_par->riva.PRAMIN);
Fixes: 1162b0701b ("ARC: I/O and DMA Mappings")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Vineet Gupta <vgupta@kernel.org>
Cc: linux-snps-arc@lists.infradead.org
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vineet Gupta <vgupta@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e705968dd6 ]
In commit 97886d9dcd ("sched: Migration changes for core scheduling"),
sched_group_cookie_match() was added to help determine if a cookie
matches the core state.
However, while it iterates the SMT group, it fails to actually use the
RQ for each of the CPUs iterated, use cpu_rq(cpu) instead of rq to fix
things.
Fixes: 97886d9dcd ("sched: Migration changes for core scheduling")
Signed-off-by: Lin Shengwang <linshengwang1@huawei.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20221008022709.642-1-linshengwang1@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca6c21327c ]
Marco reported:
Due to the implementation of how SIGTRAP are delivered if
perf_event_attr::sigtrap is set, we've noticed 3 issues:
1. Missing SIGTRAP due to a race with event_sched_out() (more
details below).
2. Hardware PMU events being disabled due to returning 1 from
perf_event_overflow(). The only way to re-enable the event is
for user space to first "properly" disable the event and then
re-enable it.
3. The inability to automatically disable an event after a
specified number of overflows via PERF_EVENT_IOC_REFRESH.
The worst of the 3 issues is problem (1), which occurs when a
pending_disable is "consumed" by a racing event_sched_out(), observed
as follows:
CPU0 | CPU1
--------------------------------+---------------------------
__perf_event_overflow() |
perf_event_disable_inatomic() |
pending_disable = CPU0 | ...
| _perf_event_enable()
| event_function_call()
| task_function_call()
| /* sends IPI to CPU0 */
<IPI> | ...
__perf_event_enable() +---------------------------
ctx_resched()
task_ctx_sched_out()
ctx_sched_out()
group_sched_out()
event_sched_out()
pending_disable = -1
</IPI>
<IRQ-work>
perf_pending_event()
perf_pending_event_disable()
/* Fails to send SIGTRAP because no pending_disable! */
</IRQ-work>
In the above case, not only is that particular SIGTRAP missed, but also
all future SIGTRAPs because 'event_limit' is not reset back to 1.
To fix, rework pending delivery of SIGTRAP via IRQ-work by introduction
of a separate 'pending_sigtrap', no longer using 'event_limit' and
'pending_disable' for its delivery.
Additionally; and different to Marco's proposed patch:
- recognise that pending_disable effectively duplicates oncpu for
the case where it is set. As such, change the irq_work handler to
use ->oncpu to target the event and use pending_* as boolean toggles.
- observe that SIGTRAP targets the ctx->task, so the context switch
optimization that carries contexts between tasks is invalid. If
the irq_work were delayed enough to hit after a context switch the
SIGTRAP would be delivered to the wrong task.
- observe that if the event gets scheduled out
(rotation/migration/context-switch/...) the irq-work would be
insufficient to deliver the SIGTRAP when the event gets scheduled
back in (the irq-work might still be pending on the old CPU).
Therefore have event_sched_out() convert the pending sigtrap into a
task_work which will deliver the signal at return_to_user.
Fixes: 97ba62b278 ("perf: Add support for SIGTRAP on perf events")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Debugged-by: Dmitry Vyukov <dvyukov@google.com>
Reported-by: Marco Elver <elver@google.com>
Debugged-by: Marco Elver <elver@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Marco Elver <elver@google.com>
Tested-by: Marco Elver <elver@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c9a3545b1d ]
Update HDMI volatile registers list as DMA, Channel Selection registers,
vbit control registers are being reflected by hardware DP port
disconnection.
This update is required to fix no display and no sound issue observed
after reconnecting TAMA/SANWA DP cables.
Once DP cable is unplugged, DMA control registers are being reset by
hardware, however at second plugin, new dma control values does not
updated to the dma hardware registers since new register value and
cached values at the time of first plugin are same.
Fixes: 7cb37b7bd0 ("ASoC: qcom: Add support for lpass hdmi driver")
Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Reported-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Link: https://lore.kernel.org/r/1665637711-13300-1-git-send-email-quic_srivasam@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05c2224d4b ]
It's required by vm_userspace_mem_region_add() that memory size
should be aligned to host page size. However, one guest page is
provided by memslot_modification_stress_test. It triggers failure
in the scenario of 64KB-page-size-host and 4KB-page-size-guest,
as the following messages indicate.
# ./memslot_modification_stress_test
Testing guest mode: PA-bits:40, VA-bits:48, 4K pages
guest physical test memory: [0xffbfff0000, 0xffffff0000)
Finished creating vCPUs
Started all vCPUs
==== Test Assertion Failure ====
lib/kvm_util.c:824: vm_adjust_num_guest_pages(vm->mode, npages) == npages
pid=5712 tid=5712 errno=0 - Success
1 0x0000000000404eeb: vm_userspace_mem_region_add at kvm_util.c:822
2 0x0000000000401a5b: add_remove_memslot at memslot_modification_stress_test.c:82
3 (inlined by) run_test at memslot_modification_stress_test.c:110
4 0x0000000000402417: for_each_guest_mode at guest_modes.c:100
5 0x00000000004016a7: main at memslot_modification_stress_test.c:187
6 0x0000ffffb8cd4383: ?? ??:0
7 0x0000000000401827: _start at :?
Number of guest pages is not compatible with the host. Try npages=16
Fix the issue by providing 16 guest pages to the memory slot for this
particular combination of 64KB-page-size-host and 4KB-page-size-guest
on aarch64.
Fixes: ef4c9f4f65 ("KVM: selftests: Fix 32-bit truncation of vm_get_max_gfn()")
Signed-off-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221013063020.201856-1-gshan@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb9ea2c31f ]
The doc says the I²C device's name is used if devname is NULL, but
actually the I²C device driver's name is used.
Fixes: 0658293012 ("media: v4l: subdev: Add a function to set an I²C sub-device's name")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 406e14808e upstream.
Before switching back to the right partition in mmc_blk_reset there used
to be a check if hw_reset was even supported. This return value
was removed, so there is no reason to check. Furthermore ensure
part_curr is not falsely set to a valid value on reset or
partition switch error.
As part of this change the code paths of mmc_blk_reset calls were checked
to ensure no commands are issued after a failed mmc_blk_reset directly
without going through the block layer.
Fixes: fefdd3c91e ("mmc: core: Drop superfluous validations in mmc_hw|sw_reset()")
Cc: stable@vger.kernel.org
Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/e91be6199d04414a91e20611c81bfe1d@hyperstone.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 1c5e670d6a.
LTS 5.15 pulled in several lpfc "SLI Path split" patches. The Path
Split mods were a 14-patch set, which refactors the driver from
to split the sli-3 hw (now eol) from the sli-4 hw and use sli4
structures natively. The patches are highly inter-related.
Given only some of the patches were included, it created a situation
where FLOGI's fail, thus SLI Ports can't start communication.
Reverting this patch as its one of the partial Path Split patches
that was included.
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit c56cc7fefc.
LTS 5.15 pulled in several lpfc "SLI Path split" patches. The Path
Split mods were a 14-patch set, which refactors the driver from
to split the sli-3 hw (now eol) from the sli-4 hw and use sli4
structures natively. The patches are highly inter-related.
Given only some of the patches were included, it created a situation
where FLOGI's fail, thus SLI Ports can't start communication.
Reverting this patch as its one of the partial Path Split patches
that was included.
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit b4543dbea8.
LTS 5.15 pulled in several lpfc "SLI Path split" patches. The Path
Split mods were a 14-patch set, which refactors the driver from
to split the sli-3 hw (now eol) from the sli-4 hw and use sli4
structures natively. The patches are highly inter-related.
Given only some of the patches were included, it created a situation
where FLOGI's fail, thus SLI Ports can't start communication.
Reverting this patch as its one of the partial Path Split patches
that was included.
NOTE: fixed a git revert error which caused a new line to be inserted:
line 5755 of lpfc_scsi.c in lpfc_queuecommand
+ atomic_inc(&ndlp->cmd_pending);
Removed the line
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 9a570069cd.
LTS 5.15 pulled in several lpfc "SLI Path split" patches. The Path
Split mods were a 14-patch set, which refactors the driver from
to split the sli-3 hw (now eol) from the sli-4 hw and use sli4
structures natively. The patches are highly inter-related.
Given only some of the patches were included, it created a situation
where FLOGI's fail, thus SLI Ports can't start communication.
Reverting this patch as its a fix specific to the Path Split patches,
which were partially included and now being pulled from 5.15.
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 6e99860de6.
LTS 5.15 pulled in several lpfc "SLI Path split" patches. The Path
Split mods were a 14-patch set, which refactors the driver from
to split the sli-3 hw (now eol) from the sli-4 hw and use sli4
structures natively. The patches are highly inter-related.
Given only some of the patches were included, it created a situation
where FLOGI's fail, thus SLI Ports can't start communication.
Reverting this patch as its a fix specific to the Path Split patches,
which were partially included and now being pulled from 5.15.
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 17bf429b91.
LTS 5.15 pulled in several lpfc "SLI Path split" patches. The Path
Split mods were a 14-patch set, which refactors the driver from
to split the sli-3 hw (now eol) from the sli-4 hw and use sli4
structures natively. The patches are highly inter-related.
Given only some of the patches were included, it created a situation
where FLOGI's fail, thus SLI Ports can't start communication.
Reverting this patch as its a fix specific to the Path Split patches,
which were partially included and now being pulled from 5.15.
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ec803025c upstream.
For some exception types the instruction address points behind the
instruction that caused the exception. Take that into account and add
the missing exception table entry.
Cc: <stable@vger.kernel.org>
Fixes: f058599e22 ("s390/pci: Fix s390_mmio_read/write with MIO")
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a262d3ad6a upstream.
For some exception types the instruction address points behind the
instruction that caused the exception. Take that into account and add
the missing exception table entry.
Cc: <stable@vger.kernel.org>
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4fd9df10cb upstream.
Since commit d9820ff ("ARC: mm: switch pgtable_t back to struct page *")
a memory leakage problem occurs. Memory allocated for page table entries
not released during process termination. This issue can be reproduced by
a small program that allocates a large amount of memory. After several
runs, you'll see that the amount of free memory has reduced and will
continue to reduce after each run. All ARC CPUs are effected by this
issue. The issue was introduced since the kernel stable release v5.15-rc1.
As described in commit d9820ff after switch pgtable_t back to struct
page *, a pointer to "struct page" and appropriate functions are used to
allocate and free a memory page for PTEs, but the pmd_pgtable macro hasn't
changed and returns the direct virtual address from the PMD (PGD) entry.
Than this address used as a parameter in the __pte_free() and as a result
this function couldn't release memory page allocated for PTEs.
Fix this issue by changing the pmd_pgtable macro and returning pointer to
struct page.
Fixes: d9820ff76f ("ARC: mm: switch pgtable_t back to struct page *")
Cc: Mike Rapoport <rppt@kernel.org>
Cc: <stable@vger.kernel.org> # 5.15.x
Signed-off-by: Pavel Kozlov <pavel.kozlov@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d917a62af8 upstream.
The signal_read(), action_read(), and action_write() callbacks have been
assuming Signal0 is requested without checking. This results in requests
for Signal1 returning data for Signal0. This patch fixes these
oversights by properly checking for the Signal's id in the respective
callbacks and handling accordingly based on the particular Signal
requested. The trig_inverted member of the mchp_tc_data is removed as
superfluous.
Fixes: 106b104137 ("counter: Add microchip TCB capture counter")
Cc: stable@vger.kernel.org
Reviewed-by: Kamel Bouhara <kamel.bouhara@bootlin.com>
Link: https://lore.kernel.org/r/20221018121014.7368-1-william.gray@linaro.org/
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6746eae4bb upstream.
cti_enable_hw() and cti_disable_hw() are called from an atomic context
so shouldn't use runtime PM because it can result in a sleep when
communicating with firmware.
Since commit 3c66563378 ("Revert "firmware: arm_scmi: Add clock
management to the SCMI power domain""), this causes a hang on Juno when
running the Perf Coresight tests or running this command:
perf record -e cs_etm//u -- ls
This was also missed until the revert commit because pm_runtime_put()
was called with the wrong device until commit 692c9a499b ("coresight:
cti: Correct the parameter for pm_runtime_put")
With lock and scheduler debugging enabled the following is output:
coresight cti_sys0: cti_enable_hw -- dev:cti_sys0 parent: 20020000.cti
BUG: sleeping function called from invalid context at drivers/base/power/runtime.c:1151
in_atomic(): 1, irqs_disabled(): 128, non_block: 0, pid: 330, name: perf-exec
preempt_count: 2, expected: 0
RCU nest depth: 0, expected: 0
INFO: lockdep is turned off.
irq event stamp: 0
hardirqs last enabled at (0): [<0000000000000000>] 0x0
hardirqs last disabled at (0): [<ffff80000822b394>] copy_process+0xa0c/0x1948
softirqs last enabled at (0): [<ffff80000822b394>] copy_process+0xa0c/0x1948
softirqs last disabled at (0): [<0000000000000000>] 0x0
CPU: 3 PID: 330 Comm: perf-exec Not tainted 6.0.0-00053-g042116d99298 #7
Hardware name: ARM LTD ARM Juno Development Platform/ARM Juno Development Platform, BIOS EDK II Sep 13 2022
Call trace:
dump_backtrace+0x134/0x140
show_stack+0x20/0x58
dump_stack_lvl+0x8c/0xb8
dump_stack+0x18/0x34
__might_resched+0x180/0x228
__might_sleep+0x50/0x88
__pm_runtime_resume+0xac/0xb0
cti_enable+0x44/0x120
coresight_control_assoc_ectdev+0xc0/0x150
coresight_enable_path+0xb4/0x288
etm_event_start+0x138/0x170
etm_event_add+0x48/0x70
event_sched_in.isra.122+0xb4/0x280
merge_sched_in+0x1fc/0x3d0
visit_groups_merge.constprop.137+0x16c/0x4b0
ctx_sched_in+0x114/0x1f0
perf_event_sched_in+0x60/0x90
ctx_resched+0x68/0xb0
perf_event_exec+0x138/0x508
begin_new_exec+0x52c/0xd40
load_elf_binary+0x6b8/0x17d0
bprm_execve+0x360/0x7f8
do_execveat_common.isra.47+0x218/0x238
__arm64_sys_execve+0x48/0x60
invoke_syscall+0x4c/0x110
el0_svc_common.constprop.4+0xfc/0x120
do_el0_svc+0x34/0xc0
el0_svc+0x40/0x98
el0t_64_sync_handler+0x98/0xc0
el0t_64_sync+0x170/0x174
Fix the issue by removing the runtime PM calls completely. They are not
needed here because it must have already been done when building the
path for a trace.
Fixes: 835d722ba1 ("coresight: cti: Initial CoreSight CTI Driver")
Cc: stable <stable@kernel.org>
Reported-by: Aishwarya TCV <Aishwarya.TCV@arm.com>
Reported-by: Cristian Marussi <Cristian.Marussi@arm.com>
Suggested-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: James Clark <james.clark@arm.com>
Reviewed-by: Mike Leach <mike.leach@linaro.org>
Tested-by: Mike Leach <mike.leach@linaro.org>
[ Fix build warnings ]
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20221025131032.1149459-1-suzuki.poulose@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d61e1d1d52 upstream.
In the S2idle suspend/resume phase the gfxoff is keeping functional so
some IP blocks will be likely to reinitialize at gfxoff entry and that
will result in failing to program GC registers.Therefore, let disallow
gfxoff until AMDGPU IPs reinitialized completely.
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 5.15.x
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5a5c4e06fd upstream.
Back in 2014, the LQI was saved in the skb control buffer (skb->cb, or
mac_cb(skb)) without any actual reset of this area prior to its use.
As part of a useful rework of the use of this region, 32edc40ae6
("ieee802154: change _cb handling slightly") introduced mac_cb_init() to
basically memset the cb field to 0. In particular, this new function got
called at the beginning of mac802154_parse_frame_start(), right before
the location where the buffer got actually filled.
What went through unnoticed however, is the fact that the very first
helper called by device drivers in the receive path already used this
area to save the LQI value for later extraction. Resetting the cb field
"so late" led to systematically zeroing the LQI.
If we consider the reset of the cb field needed, we can make it as soon
as we get an skb from a device driver, right before storing the LQI,
as is the very first time we need to write something there.
Cc: stable@vger.kernel.org
Fixes: 32edc40ae6 ("ieee802154: change _cb handling slightly")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20221020142535.1038885-1-miquel.raynal@bootlin.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f5c8cf2a49 upstream.
Commit 46573fd636 ("cpufreq: intel_pstate: hybrid: Rework HWP
calibration") attempted to use the information from CPPC (the nominal
performance in particular) to obtain the scaling factor allowing the
frequency to be computed if the HWP performance level of the given CPU
is known or vice versa.
However, it turns out that on some platforms this doesn't work, because
the CPPC information on them does not align with the contents of the
MSR_HWP_CAPABILITIES registers.
This basically means that the only way to make intel_pstate work on all
of the hybrid platforms to date is to use the observation that on all
of them the scaling factor between the HWP performance levels and
frequency for P-cores is 78741 (approximately 100000/1.27). For
E-cores it is 100000, which is the same as for all of the non-hybrid
"core" platforms and does not require any changes.
Accordingly, make intel_pstate use 78741 as the scaling factor between
HWP performance levels and frequency for P-cores on all hybrid platforms
and drop the dependency of the HWP calibration code on CPPC.
Fixes: 46573fd636 ("cpufreq: intel_pstate: hybrid: Rework HWP calibration")
Reported-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: 5.15+ <stable@vger.kernel.org> # 5.15+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8dbab94d45 upstream.
Some of the MSR accesses in intel_pstate are carried out on the CPU
that is running the code, but the values coming from them are used
for the performance scaling of the other CPUs.
This is problematic, for example, on hybrid platforms where
MSR_TURBO_RATIO_LIMIT for P-cores and E-cores is different, so the
values read from it on a P-core are generally not applicable to E-cores
and the other way around.
For this reason, make the driver access all MSRs on the target CPU on
platforms using the "core" pstate_funcs callbacks which is the case for
all of the hybrid platforms released to date. For this purpose, pass
a CPU argument to the ->get_max(), ->get_max_physical(), ->get_min()
and ->get_turbo() pstate_funcs callbacks and from there pass it to
rdmsrl_on_cpu() or rdmsrl_safe_on_cpu() to access the MSR on the target
CPU.
Fixes: 46573fd636 ("cpufreq: intel_pstate: hybrid: Rework HWP calibration")
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: 5.15+ <stable@vger.kernel.org> # 5.15+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ab0ee36e90 upstream.
The iio_triggered_buffer_setup_ext() was changed by
commit 15097c7a1a ("iio: buffer: wrap all buffer attributes into iio_dev_attr")
to silently expect that all attributes given in buffer_attrs array are
device-attributes. This expectation was not forced by the API - and some
drivers did register attributes created by IIO_CONST_ATTR().
The added attribute "wrapping" does not copy the pointer to stored
string constant and when the sysfs file is read the kernel will access
to invalid location.
Change the IIO_CONST_ATTRs from the driver to IIO_DEVICE_ATTR in order
to prevent the invalid memory access.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Fixes: 15097c7a1a ("iio: buffer: wrap all buffer attributes into iio_dev_attr")
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/19158499623cdf7f9c5efae1f13c9f1a918ff75f.1664782676.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5aed5b7c24 upstream.
Endpoints are normally deleted from the bandwidth list when they are
dropped, before the virt device is freed.
If xHC host is dying or being removed then the endpoints aren't dropped
cleanly due to functions returning early to avoid interacting with a
non-accessible host controller.
So check and delete endpoints that are still on the bandwidth list when
freeing the virt device.
Solves a list_del corruption kernel crash when unbinding xhci-pci,
caused by xhci_mem_cleanup() when it later tried to delete already freed
endpoints from the bandwidth list.
This only affects hosts that use software bandwidth checking, which
currenty is only the xHC in intel Panther Point PCH (Ivy Bridge)
Cc: stable@vger.kernel.org
Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20221024142720.4122053-5-mathias.nyman@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 34cd2db408 upstream.
Systems based on Alder Lake P see significant boot time delay if
boot firmware tries to control usb ports in unexpected link states.
This is seen with self-powered usb devices that survive in U3 link
suspended state over S5.
A more generic solution to power off ports at shutdown was attempted in
commit 83810f84ec ("xhci: turn off port power in shutdown")
but it caused regression.
Add host specific XHCI_RESET_TO_DEFAULT quirk which will reset host and
ports back to default state in shutdown.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20221024142720.4122053-3-mathias.nyman@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0a0a2760b0 upstream.
If there is a transmission error the buffer will be returned too early,
causing a memory fault as subsequent requests for that buffer are still
queued up to be sent. Refactor the error handling to wait for the final
request to come in before reporting back the buffer to userspace for all
transfer types (bulk/isoc/isoc_sg). This ensures userspace knows if the
frame was successfully sent.
Fixes: e81e7f9a0e ("usb: gadget: uvc: add scatter gather support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Vacura <w36195@motorola.com>
Link: https://lore.kernel.org/r/20221018215044.765044-4-w36195@motorola.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 50895a55bc upstream.
With char becoming unsigned by default, and with `char` alone being
ambiguous and based on architecture, signed chars need to be marked
explicitly as such. This fixes warnings like:
sound/pci/rme9652/hdsp.c:3953 hdsp_channel_buffer_location() warn: 'hdsp->channel_map[channel]' is unsigned
sound/pci/rme9652/hdsp.c:4153 snd_hdsp_channel_info() warn: impossible condition '(hdsp->channel_map[channel] < 0) => (0-255 < 0)'
sound/pci/rme9652/rme9652.c:1833 rme9652_channel_buffer_location() warn: 'rme9652->channel_map[channel]' is unsigned
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20221025000313.546261-1-Jason@zx2c4.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee03c0f200 upstream.
With char becoming unsigned by default, and with `char` alone being
ambiguous and based on architecture, signed chars need to be marked
explicitly as such. This fixes warnings like:
sound/pci/au88x0/au88x0_core.c:2029 vortex_adb_checkinout() warn: signedness bug returning '(-22)'
sound/pci/au88x0/au88x0_core.c:2046 vortex_adb_checkinout() warn: signedness bug returning '(-12)'
sound/pci/au88x0/au88x0_core.c:2125 vortex_adb_allocroute() warn: 'vortex_adb_checkinout(vortex, (0), en, 0)' is unsigned
sound/pci/au88x0/au88x0_core.c:2170 vortex_adb_allocroute() warn: 'vortex_adb_checkinout(vortex, stream->resources, en, 4)' is unsigned
As well, since one function returns errnos, return an `int` rather than
a `signed char`.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20221024162929.536004-1-Jason@zx2c4.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f0a868788f upstream.
The current code for freeing the emux timer is extremely dangerous:
CPU0 CPU1
---- ----
snd_emux_timer_callback()
snd_emux_free()
spin_lock(&emu->voice_lock)
del_timer(&emu->tlist); <-- returns immediately
spin_unlock(&emu->voice_lock);
[..]
kfree(emu);
spin_lock(&emu->voice_lock);
[BOOM!]
Instead just use del_timer_sync() which will wait for the timer to finish
before continuing. No need to check if the timer is active or not when
doing so.
This doesn't fix the race of a possible re-arming of the timer, but at
least it won't use the data that has just been freed.
[ Fixed unused variable warning by tiwai ]
Cc: stable@vger.kernel.org
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20221026231236.6834b551@gandalf.local.home
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2871edb32f upstream.
kvaser_usb uses completions to signal when a response event is received
for outgoing commands.
However, it uses init_completion() to reinitialize the start_comp and
stop_comp completions before sending the start/stop commands.
In case the device sends the corresponding response just before the
actual command is sent, complete() may be called concurrently with
init_completion() which is not safe.
This might be triggerable even with a properly functioning device by
stopping the interface (CMD_STOP_CHIP) just after it goes bus-off (which
also causes the driver to send CMD_STOP_CHIP when restart-ms is off),
but that was not tested.
Fix the issue by using reinit_completion() instead.
Fixes: 080f40a6fa ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010185237.319219-2-extja@kvaser.com
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c3ed222745 upstream.
Send along the already-allocated fattr along with nfs4_fs_locations, and
drop the memcpy of fattr. We end up growing two more allocations, but this
fixes up a crash as:
PID: 790 TASK: ffff88811b43c000 CPU: 0 COMMAND: "ls"
#0 [ffffc90000857920] panic at ffffffff81b9bfde
#1 [ffffc900008579c0] do_trap at ffffffff81023a9b
#2 [ffffc90000857a10] do_error_trap at ffffffff81023b78
#3 [ffffc90000857a58] exc_stack_segment at ffffffff81be1f45
#4 [ffffc90000857a80] asm_exc_stack_segment at ffffffff81c009de
#5 [ffffc90000857b08] nfs_lookup at ffffffffa0302322 [nfs]
#6 [ffffc90000857b70] __lookup_slow at ffffffff813a4a5f
#7 [ffffc90000857c60] walk_component at ffffffff813a86c4
#8 [ffffc90000857cb8] path_lookupat at ffffffff813a9553
#9 [ffffc90000857cf0] filename_lookup at ffffffff813ab86b
Suggested-by: Trond Myklebust <trondmy@hammerspace.com>
Fixes: 9558a007db ("NFS: Remove the label from the nfs4_lookup_res struct")
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-11-03 23:59:10 +09:00
1026 changed files with 15482 additions and 7225 deletions
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
