We need to be able to specify different HPD pin active values in the
DT based on the RPi board. Just force HDMI on for now.
Signed-off-by: Eric Anholt <eric@anholt.net>
The Raspberry Pi Foundation's firmware updates are shipping device
trees using the old string, so we'll keep recognizing that as this rev
of V3D. Still, we should use a more specific name in the upstream DT
to clarify which board is being supported, in case we do other revs of
V3D in the future.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
(cherry picked from commit 90d7116061)
The original Raspberry Pi had the GPIO active high, but the later
models are active low. The DT GPIO bindings allow specifying the
active flag, except that it doesn't get propagated to the gpiodesc, so
you have to handle it yourself.
Signed-off-by: Eric Anholt <eric@anholt.net>
Tested-by: Daniel Stone <daniels@collabora.com>
(cherry picked from commit 0b06e0a794)
Fixes an error thrown every few seconds when we poll HPD when it's on
a I2C to GPIO expander.
Signed-off-by: Eric Anholt <eric@anholt.net>
Tested-by: Daniel Stone <daniels@collabora.com>
(cherry picked from commit 0e60eab575)
The hardware provides us with separate threads for binning and
rendering, and the existing model waits for them both to complete
before submitting the next job.
Splitting the binning and rendering submissions reduces idle time and
gives us approx 20-30% speedup with some x11perf tests such as -line10
and -tilerect1. Improves openarena performance by 1.01897% +/-
0.247857% (n=16).
Thanks to anholt for suggesting this.
v2: Rebase on the spurious resets fix (change by anholt).
Signed-off-by: Varad Gautam <varadgautam@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
(cherry picked from commit ca26d28bba)
We weren't updating the interlaced bit, so we'd scan out incorrectly
if the firmware had brought up the TV encoder and we were switching to
HDMI.
Signed-off-by: Eric Anholt <eric@anholt.net>
(cherry picked from commit 6a60920986)
It looks like when I went to add the interlaced bits, I just took the
existing PV_VERT* block and indented it, instead of copy and pasting
it first. Without this, changing resolution never worked.
Signed-off-by: Eric Anholt <eric@anholt.net>
(cherry picked from commit a7c5047d1c)
This is also involved in the HDMI setup sequence so it's nice to see
it.
Signed-off-by: Eric Anholt <eric@anholt.net>
(cherry picked from commit 936f1a53f3)
If the firmware hadn't brought up HDMI for us, we need to do its
power-on reset sequence (reset HD and and clear its STANDBY bits,
reset HDMI, and leave the PHY disabled).
Signed-off-by: Eric Anholt <eric@anholt.net>
(cherry picked from commit 851479ad59)
We'd need X to queue up an async pageflip while another is
outstanding, and then take a SIGIO. I think X actually avoids sending
out the next pageflip while one's already queued, but I'm not sure.
Signed-off-by: Eric Anholt <eric@anholt.net>
(cherry picked from commit 48627eb8dc)
This supports 420 and 422 subsampling with 2 or 3 planes, tested with
modetest. It doesn't set up chroma subsampling position (which it
appears KMS doesn't deal with yet).
The LBM memory is overallocated in many cases, but apparently the docs
aren't quite correct and I'll probably need to look at the hardware
source to really figure it out.
Signed-off-by: Eric Anholt <eric@anholt.net>
(cherry picked from commit fc04023faf)
This implements a simple policy for choosing scaling modes
(trapezoidal for decimation, PPF for magnification), and a single PPF
filter (Mitchell/Netravali's recommendation).
Signed-off-by: Eric Anholt <eric@anholt.net>
(cherry picked from commit 21af94cf1a)
This doesn't matter yet since we only allow 1:1 scaling, but the
comment clearly says we should be using the source size.
Signed-off-by: Eric Anholt <eric@anholt.net>
(cherry picked from commit f863e35601)
Previously we only did the primary and cursor plane, but overlay
planes are useful and just require this setup to add, since all planes
go into the HVS display list in the same way.
Signed-off-by: Eric Anholt <eric@anholt.net>
(cherry picked from commit fc2d6f1eab)
So far, we've only ever lit up one CRTC, so this has been fine. To
extend to more displays or more planes, we need to make sure we don't
run our display lists into each other.
Signed-off-by: Eric Anholt <eric@anholt.net>
(cherry picked from commit d8dbf44f13)
Previously, on every modeset we would allocate new display list
memory, recompute changed planes, write all of them to the new memory,
and pointed scanout at the new list (which will latch approximately at
the next line of scanout). We let
drm_atomic_helper_wait_for_vblanks() decide whether we needed to wait
for a vblank after a modeset before cleaning up the old state and
letting the next modeset proceed, and on legacy cursor updates we
wouldn't wait. If you moved the cursor fast enough, we could
potentially wrap around the display list memory area and overwrite the
existing display list while it was still being scanned out, resulting
in the HVS scanning out garbage or just halting.
Instead of making cursor updates wait for scanout to move to the new
display list area (which introduces significant cursor lag in X), we
just rewrite our current display list.
Signed-off-by: Eric Anholt <eric@anholt.net>
(cherry picked from commit 6674a904d6)
As we add actual scaling, this is going to get way more complicated.
Signed-off-by: Eric Anholt <eric@anholt.net>
(cherry picked from commit 5c67999420)
This is the pointer to the HVS device's memory where we stored the
contents of *dlist.
Signed-off-by: Eric Anholt <eric@anholt.net>
(cherry picked from commit 17eac75111)
Add AVE0, DFT, GP0, GP1, GP2, SLIM, SMI, TEC, DPI, CAM0, CAM1, DSI0E,
and DSI1E. PULSE is not added because it has an extra divider.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
(cherry picked from commit d3d6f15fd3)
Enable the PCM clock in the SOC, which is used by the
bcm2835-i2s driver.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
(cherry picked from commit 33b689600f)
Reorganize bcm2835_clock_array so that there is no more
need for separate bcm2835_*_data structures to be defined.
Instead the required structures are generated inline via
helper macros.
To allow this to also work for pll alone it was required that
the parent_pll was changed from a pointer to bcm2835_pll_data
to the name of the pll instead.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
(cherry picked from commit 3b15afefbe)
As the use of BCM2835_CLOCK_COUNT in
include/dt-bindings/clock/bcm2835.h is frowned upon as
it needs to get modified every time a new clock gets introduced
this patch changes the clk-bcm2835 driver to use a different
scheme for registration of clocks and pll, so that there
is no more need for BCM2835_CLOCK_COUNT to be defined.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
(cherry picked from commit 56eb3a2ed9)
For debugging purposes under some circumstance
it helps to be able to see the actual clock registers.
E.g: when looking at the clock divider it is helpful to
see what the actual clock divider is.
This patch exposes all the clock registers specific to each
clock/pll/pll-divider via debugfs.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Eric Anholt <eric@anholt.net>
(cherry picked from commit 96bf9c69d5)
Disable wireless power saving in the brcmfmac WLAN driver. This is a
temporary measure until the connectivity loss resulting from power
saving is resolved.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Change the filenames and extensions to keep the pre-DDT style of
overlay (<name>-overlay.dtb) distinct from new ones that use a
different style of local fixups (<name>.dtbo), and to match other
platforms.
The RPi firmware uses the DDTK trailer atom to choose which type of
overlay to use for each kernel.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
This is a port of Pantelis Antoniou's v3 port that makes use of the
new upstreamed configfs support for binary attributes.
Original commit message:
Add a runtime interface to using configfs for generic device tree overlay
usage. With it its possible to use device tree overlays without having
to use a per-platform overlay manager.
Please see Documentation/devicetree/configfs-overlays.txt for more info.
Changes since v2:
- Removed ifdef CONFIG_OF_OVERLAY (since for now it's required)
- Created a documentation entry
- Slight rewording in Kconfig
Changes since v1:
- of_resolve() -> of_resolve_phandles().
Originally-signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835: extend allowed range of channels and samplerates
Allow everything the videocore accepts.
bcm2835: restrict channels*rate to 8*960000
This is required at least for SPDIF. If the bitrate goes above,
videocore will either resample the audio or corrupt it due to
underruns. Supposedly the hardware isn't designed to output
higher rates, but it can still resample it down to supported
rates.
Some code is based on ac97_pcm.c.
rpi: update vc_vchi_audioserv_defs.h
Add audioserv 3 extensions. The changes were taken from the paste
linked here:
https://github.com/raspberrypi/linux/pull/1166#issuecomment-151917067
bcm2835: implement channel map API
Report all layouts supported by the HDMI protocol to userspace.
Make the videocore set the correct layout according to the
userspace request.
Some code taken from patch_hdmi.c. In particular, the HDMI channel
layout table was copied without changes - with the idea in mind that
hopefully it can be shared one day. Or at least updating it will be
simpler.
In my tests, everything appears to work, except when outputting
FL FR RL RR. Then my receiver outputs RL on both the RL and RR
speakers, while RR is never heard.
bcm2835: access controls under the audio mutex
I don't think the ALSA framework provides any kind of automatic
synchronization within the control callbacks. We most likely need
to ensure this manually, so add locking around all access to shared
mutable data. In particular, bcm2835_audio_set_ctls() should
probably always be called under our own audio lock.
bcm2835: always use 2/4/8 channels for multichannel layouts
Pad the unused channels with NA. This means userspace needs to write
additional, silent padding channels, which is not ideal, but better
than noise.
Works around noise at the following channel counts: 3, 5, 6, 7
bcm2835: only allow stereo if analogue jack is selected
Sending more than 2 channels to videocore while outputting to analogue
mysteriously outputs heavy artifacts. So just paint it over with a
hack: if analogue is explicitly selected as destination, do not
reporting support for anything other than stereo.
I'm not sure how to deal with the auto case (destination 0). There's
probably way to retrieve this and even to listen to plug events, but
I didn't find one yet, and it's probably not worth the trouble. Just
don't use this setting, I guess. Unless you like noise.
Changing the setting while an audio stream is active also doesn't
work properly. We could probably interrupt running streams by
returning ENODEV or using kernel hotplug stuff (maybe), but that
also doesn't seem worth the trouble.
bcm2835: interpolate audio delay
It appears the GPU only sends us a message all 10ms to update
the playback progress. Other than this, the playback position
(what SNDRV_PCM_IOCTL_DELAY will return) is not updated at all.
Userspace will see jitter up to 10ms in the audio position.
Make this a bit nicer for userspace by interpolating the
position using the CPU clock.
I'm not sure if setting snd_pcm_runtime.delay is the right
approach for this. Or if there is maybe an already existing
mechanism for position interpolation in the ALSA core.
I only set SNDRV_PCM_INFO_BATCH because this appears to remove
at least one situation snd_pcm_runtime.delay is used, so I have
to worry less in which place I have to update this field, or
how it interacts with the rest of ALSA.
In the future, it might be nice to use VC_AUDIO_MSG_TYPE_LATENCY.
One problem is that it requires sending a videocore message, and
waiting for a reply, which could make the implementation much
harder due to locking and synchronization requirements.
Add non-mainline source for rtl8192cu wireless driver version v4.0.2_9000 as
this is widely used. Disable older rtlwifi driver.
8192cu needs old wireless extensions
The obsolete WIRELESS_EXT configuration is used
by the old Realtek code and is needed for AP support.
8192cu: CONFIG_AP_MODE hardcoded in autoconf.h
rtl8192c_rf6052: PHY_RFShadowRefresh(): fix off-by-one
Signed-off-by: Marc Kleine-Budde <mkl@blackshift.org>
rtl8192cu: Add PID for D-Link DWA 131
The pl011 driver looks for DT aliases of the form "serial<n>",
and if found uses <n> as the device ID. This can cause
/dev/ttyAMA0 to become /dev/ttyAMA1, which is confusing if the
other serial port is provided by the 8250 driver which doesn't
use the same logic.
The built-in RPi adaptor will still get a MAC address based on the parameter passed on the command line as the RPi hardware does not have an eeprom,
however usb->ethernet adaptors using the same driver should have an eeprom with MAC address as part of their hardware and therefore will use this
meaning they don't end up with the same MAC address as the built-in RPi adaptor.
For RTC chips with no IRQ directly connected to the SoC, the RTC chip
can be forced as a wakeup source by stating that explicitly in
the device's .dts file using the "wakeup-source" boolean property.
This will guarantee the 'wakealarm' sysfs entry is available on the
device, if supported by the RTC.
With these changes to the driver rtc-ds1307 and the necessary entries
in the .dts file, I get an working ds1337 RTC on the Witty Pi extension
board by UUGear for the Raspberry Pi.
An example for the entry in the .dts file:
rtc: ds1337@68 {
compatible = "dallas,ds1337";
reg = <0x68>;
wakeup-source;
If the "wakeup-source" property is set, do not request an IRQ.
Set also UIE mode to unsupported, to get a working 'hwclock' binary.
Signed-off-by: Michael Lange <linuxstuff@milaw.biz>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Code copied from spi-bcm2835. Get physical address from devicetree
instead of using hardcoded constant.
Signed-off-by: Matthias Reichl <hias@horus.com>
The firmware uses tags in the kernel trailer to choose which dtb file
to load. Current firmware loads bcm2835-*.dtb if the '283x' tag is true,
otherwise it loads bcm270*.dtb. This scheme breaks if an image supports
multiple platforms.
This patch adds '270X' and '283X' tags to indicate support for RPi and
upstream platforms, respectively. '283x' (note lower case 'x') is left
for old firmware, and is only set if the image only supports upstream
builds.
Add a mailbox-driven backlight controller for the Raspberry Pi DSI
touchscreen display. Requires updated GPU firmware to recognise the
mailbox request.
Signed-off-by: Gordon Hollingworth <gordon@raspberrypi.org>
Signed-off-by: Jan Grulich <jan@grulich.eu>
config: fix RaspiDAC Rev.3x dependencies
Change depends to SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S
like the other I2S soundcard drivers.
Signed-off-by: Matthias Reichl <hias@horus.com>
The Raspberry Pi firmware manages the power-down and reboot
process. To do this it installs a pm_power_off handler, causing
the gpio-poweroff module to abort the probe function.
This patch introduces a "force" DT property that overrides that
behaviour, and also adds a DT overlay to enable and control it.
Note that running in an active-low configuration (DT parameter
"active_low") requires a custom dt-blob.bin and probably won't
allow a reboot without switching off, so an external inversion
of the trigger signal may be preferable.
Provide a __copy_from_user that uses memcpy. On BCM2708, use
optimised memcpy/memmove/memcmp/memset implementations.
arch/arm: Add mmiocpy/set aliases for memcpy/set
See: https://github.com/raspberrypi/linux/issues/1082
copy_from_user: CPU_SW_DOMAIN_PAN compatibility
The downstream copy_from_user acceleration must also play nice with
CONFIG_CPU_SW_DOMAIN_PAN.
See: https://github.com/raspberrypi/linux/issues/1381
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The "input" trigger makes the associated GPIO an input. This is to support
the Raspberry Pi PWR LED, which is driven by external hardware in normal use.
N.B. pwr_led is not available on Model A or B boards.
leds-gpio: Implement the brightness_get method
The power LED uses some clever logic that means it is driven
by a voltage measuring circuit when configured as input, otherwise
it is driven by the GPIO output value. This patch wires up the
brightness_get method for leds-gpio so that user-space can monitor
the LED value via /sys/class/gpio/led1/brightness. Using the input
trigger this returns an indication of the system power health,
otherwise it is just whatever value the trigger has written most
recently.
See: https://github.com/raspberrypi/linux/issues/1064
The driver contains a low-level hardware driver for the TAS5713 and the
drivers for the Raspberry Pi I2S subsystem.
TAS5713: return error if initialisation fails
Existing TAS5713 driver logs errors during initialisation, but does not return
an error code. Therefore even if initialisation fails, the driver will still be
loaded, but won't work. This patch fixes this. I2C communication error will now
reported correctly by a non-zero return code.
HiFiBerry Amp: fix device-tree problems
Some code to load the driver based on device-tree-overlays was missing. This is added by this patch.
The driver is based on the HiFiBerry DAC driver. However HiFiBerry DAC+ uses
a different codec chip (PCM5122), therefore a new driver is necessary.
Add support for the HiFiBerry DAC+ Pro.
The HiFiBerry DAC+ and DAC+ Pro products both use the existing bcm sound driver with the DAC+ Pro having a special clock device driver representing the two high precision oscillators.
An addition bug fix is included for the PCM512x codec where by the physical size of the sample frame is used in the calculation of the LRCK divisor as it was found to be wrong when using 24-bit depth sample contained in a little endian 4-byte sample frame.
Limit PCM512x "Digital" gain to 0dB by default with HiFiBerry DAC+
24db_digital_gain DT param can be used to specify that PCM512x
codec "Digital" volume control should not be limited to 0dB gain,
and if specified will allow the full 24dB gain.
Set a limit of 0dB on Digital Volume Control
The main volume control in the PCM512x DAC has a range up to
+24dB. This is dangerously loud and can potentially cause massive
clipping in the output stages. Therefore this sets a sensible
limit of 0dB for this control.
Allow up to 24dB digital gain to be applied when using IQAudIO DAC+
24db_digital_gain DT param can be used to specify that PCM512x
codec "Digital" volume control should not be limited to 0dB gain,
and if specified will allow the full 24dB gain.
Signed-off-by: Daniel Matuschek <daniel@matuschek.net>
Add a parameter to turn off SPDIF output if no audio is playing
This patch adds the paramater auto_shutdown_output to the kernel module.
Default behaviour of the module is the same, but when auto_shutdown_output
is set to 1, the SPDIF oputput will shutdown if no stream is playing.
bugfix for 32kHz sample rate, was missing
HiFiBerry Digi: set SPDIF status bits for sample rate
The HiFiBerry Digi driver did not signal the sample rate in the SPDIF status bits.
While this is optional, some DACs and receivers do not accept this signal. This patch
adds the sample rate bits in the SPDIF status block.
This adds a machine driver for the HifiBerry DAC.
It is a sound card that can
be stacked onto the Raspberry Pi.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
1-wire: Add support for configuring pin for w1-gpio kernel module
See: https://github.com/raspberrypi/linux/pull/457
Add bitbanging pullups, use them for w1-gpio
Allows parasite power to work, uses module option pullup=1
bcm2708: Ensure 1-wire pullup is disabled by default, and expose as module parameter
Signed-off-by: Alex J Lennon <ajlennon@dynamicdevices.co.uk>
w1-gpio: Add gpiopin module parameter and correctly free up gpio pull-up pin, if set
Signed-off-by: Alex J Lennon <ajlennon@dynamicdevices.co.uk>
w1-gpio: Sort out the pullup/parasitic power tangle
Especially on platforms with a slower CPU but a relatively high
framebuffer fill bandwidth, like current ARM devices, the existing
console monochrome imageblit function used to draw console text is
suboptimal for common pixel depths such as 16bpp and 32bpp. The existing
code is quite general and can deal with several pixel depths. By creating
special case functions for 16bpp and 32bpp, by far the most common pixel
formats used on modern systems, a significant speed-up is attained
which can be readily felt on ARM-based devices like the Raspberry Pi
and the Allwinner platform, but should help any platform using the
fb layer.
The special case functions allow constant folding, eliminating a number
of instructions including divide operations, and allow the use of an
unrolled loop, eliminating instructions with a variable shift size,
reducing source memory access instructions, and eliminating excessive
branching. These unrolled loops also allow much better code optimization
by the C compiler. The code that selects which optimized variant is used
is also simplified, eliminating integer divide instructions.
The speed-up, measured by timing 'cat file.txt' in the console, varies
between 40% and 70%, when testing on the Raspberry Pi and Allwinner
ARM-based platforms, depending on font size and the pixel depth, with
the greater benefit for 32bpp.
Signed-off-by: Harm Hanemaaijer <fgenfb@yahoo.com>
Based on the patch authored by Ali Gholami Rudi at
https://lkml.org/lkml/2009/7/13/153
Provide an ioctl for userspace applications, but only if this operation
is hardware accelerated (otherwide it does not make any sense).
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Add the bare minimum needed to boot BCM2708 from a Device Tree.
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
BCM2708: DT: change 'axi' nodename to 'soc'
Change DT node named 'axi' to 'soc' so it matches ARCH_BCM2835.
The VC4 bootloader fills in certain properties in the 'axi' subtree,
but since this is part of an upstreaming effort, the name is changed.
Signed-off-by: Noralf Tronnes notro@tronnes.org
BCM2708_DT: Correct length of the peripheral space
Use dts-dirs feature for overlays.
The kernel makefiles have a dts-dirs target that is for vendor subdirectories.
Using this fixes the install_dtbs target, which previously did not install the overlays.
BCM270X_DT: configure I2S DMA channels
Signed-off-by: Matthias Reichl <hias@horus.com>
BCM270X_DT: switch to bcm2835-i2s
I2S soundcard drivers with proper devicetree support (i.e. not linking
to the cpu_dai/platform via name but to cpu/platform via of_node)
will work out of the box without any modifications.
When the kernel is compiled without devicetree support the platform
code will instantiate the bcm2708-i2s driver and I2S soundcard drivers
will link to it via name, as before.
Signed-off-by: Matthias Reichl <hias@horus.com>
SDIO-overlay: add poll_once-boolean parameter
Add paramter to toggle sdio-device-polling
done every second or once at boot-time.
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
BCM270X_DT: Make mmc overlay compatible with current firmware
The original DT overlay logic followed a merge-then-patch procedure,
i.e. parameters are applied to the loaded overlay before the overlay
is merged into the base DTB. This sequence has been changed to
patch-then-merge, in order to support parameterised node names, and
to protect against bad overlays. As a result, overrides (parameters)
must only target labels in the overlay, but the overlay can obviously target nodes in the base DTB.
mmc-overlay.dts (that switches back to the original mmc sdcard
driver) is the only overlay violating that rule, and this patch
fixes it.
bcm270x_dt: Use the sdhost MMC controller by default
The "mmc" overlay reverts to using the other controller.
squash: Add cprman to dt
BCM270X_DT: Use clk_core for I2C interfaces
The Raspberry Pi firmware looks for a trailer on the kernel image to
determine whether it was compiled with Device Tree support enabled.
If the firmware finds a kernel without this trailer, or which has a
trailer indicating that it isn't DT-capable, it disables DT support
and reverts to using ATAGs.
The mkknlimg utility adds that trailer, having first analysed the
image to look for signs of DT support and the kernel version string.
knlinfo displays the contents of the trailer in the given kernel image.
scripts/mkknlimg: Add support for ARCH_BCM2835
Add a new trailer field indicating whether this is an ARCH_BCM2835
build, as opposed to MACH_BCM2708/9. If the loader finds this flag
is set it changes the default base dtb file name from bcm270x...
to bcm283y...
Also update knlinfo to show the status of the field.
scripts/mkknlimg: Improve ARCH_BCM2835 detection
The board support code contains sufficient strings to be able to
distinguish 2708 vs. 2835 builds, so remove the check for
bcm2835-pm-wdt which could exist in either.
Also, since the canned configuration is no longer built in (it's
a module), remove the config string checking.
See: https://github.com/raspberrypi/linux/issues/1157
- Supports raw YUV capture, preview, JPEG and H264.
- Uses videobuf2 for data transfer, using dma_buf.
- Uses 3.6.10 timestamping
- Camera power based on use
- Uses immutable input mode on video encoder
Signed-off-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Luke Diamand <luked@broadcom.com>
V4L2: Fixes from 6by9
V4L2: Fix EV values. Add manual shutter speed control
V4L2 EV values should be in units of 1/1000. Corrected.
Add support for V4L2_CID_EXPOSURE_ABSOLUTE which should
give manual shutter control. Requires manual exposure mode
to be selected first.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Correct JPEG Q-factor range
Should be 1-100, not 0-100
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Fix issue of driver jamming if STREAMON failed.
Fix issue where the driver was left in a partially enabled
state if STREAMON failed, and would then reject many IOCTLs
as it thought it was streaming.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Fix ISO controls.
Driver was passing the index to the GPU, and not the desired
ISO value.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Add flicker avoidance controls
Add support for V4L2_CID_POWER_LINE_FREQUENCY to set flicker
avoidance frequencies.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Add support for frame rate control.
Add support for frame rate (or time per frame as V4L2
inverts it) control via s_parm.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Improve G_FBUF handling so we pass conformance
Return some sane numbers for get framebuffer so that
we pass conformance.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Fix information advertised through g_vidfmt
Width and height were being stored based on incorrect
values.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Add support for inline H264 headers
Add support for V4L2_CID_MPEG_VIDEO_REPEAT_SEQ_HEADER
to control H264 inline headers.
Requires firmware fix to work correctly, otherwise format
has to be set to H264 before this parameter is set.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Fix JPEG timestamp issue
JPEG images were coming through from the GPU with timestamp
of 0. Detect this and give current system time instead
of some invalid value.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Fix issue when switching down JPEG resolution.
JPEG buffer size calculation is based on input resolution.
Input resolution was being configured after output port
format. Caused failures if switching from one JPEG resolution
to a smaller one.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Enable MJPEG encoding
Requires GPU firmware update to support MJPEG encoder.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Correct flag settings for compressed formats
Set flags field correctly on enum_fmt_vid_cap for compressed
image formats.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: H264 profile & level ctrls, FPS control and auto exp pri
Several control handling updates.
H264 profile and level controls.
Timeperframe/FPS reworked to add V4L2_CID_EXPOSURE_AUTO_PRIORITY to
select whether AE is allowed to override the framerate specified.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Correct BGR24 to RGB24 in format table
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Add additional pixel formats. Correct colourspace
Adds the other flavours of YUYV, and NV12.
Corrects the overlay advertised colourspace.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Drop logging msg from info to debug
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Initial pass at scene modes.
Only supports exposure mode and metering modes.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Add manual white balance control.
Adds support for V4L2_CID_RED_BALANCE and
V4L2_CID_BLUE_BALANCE. Only has an effect if
V4L2_CID_AUTO_N_PRESET_WHITE_BALANCE has
V4L2_WHITE_BALANCE_MANUAL selected.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
config: Enable V4L / MMAL driver
V4L2: Increase the MMAL timeout to 3sec
MJPEG codec flush is now taking longer and results
in a kernel panic if the driver has stopped waiting for
the result when it finally completes.
Increase the timeout value from 1 to 3secs.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Add support for setting H264_I_PERIOD
Adds support for the parameter V4L2_CID_MPEG_VIDEO_H264_I_PERIOD
to set the frequency with which I frames are produced.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Enable GPU function for removing padding from images.
GPU can now support arbitrary strides, although may require
additional processing to achieve it. Enable this feature
so that the images delivered are the size requested.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Add support for V4L2_PIX_FMT_BGR32
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Set the colourspace to avoid odd YUV-RGB conversions
Removes the amiguity from the conversion routines and stops
them dropping back to the SD vs HD choice of coeffs.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Make video/still threshold a run-time param
Move the define for at what resolution the driver
switches from a video mode capture to a stills mode
capture to module parameters.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Fix incorrect pool sizing
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Add option to disable enum_framesizes.
Gstreamer's handling of a driver that advertises
V4L2_FRMSIZE_TYPE_STEPWISE to define the supported
resolutions is broken. See bug
https://bugzilla.gnome.org/show_bug.cgi?id=726521
Optional parameter of gst_v4l2src_is_broken added.
If non-zero, the driver claims not to support that
ioctl, and gstreamer should be happy again (it
guesses a set of defaults for itself).
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Add support for more image formats
Adds YVU420 (YV12), YVU420SP (NV21), and BGR888.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Extend range for V4L2_CID_MPEG_VIDEO_H264_I_PERIOD
Request to extend the range from the fairly arbitrary
1000 frames (33 seconds at 30fps). Extend out to the
max range supported (int32 value).
Also allow 0, which is handled by the codec as only
send an I-frame on the first frame and never again.
There may be an exception if it detects a significant
scene change, but there's no easy way around that.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
bcm2835-camera: stop_streaming now has a void return
BCM2835-V4L2: Fix compliance test failures
VIDIOC_TRY_FMT and VIDIOC_S_FMT tests were faling due
to reporting V4L2_COLORSPACE_JPEG when the colour
format wasn't V4L2_PIX_FMT_JPEG.
Now reports V4L2_COLORSPACE_SMPTE170M for YUV formats.
bcm2835 camera planar/packed stride length
Added a field to the mmal_fmt struct used to compute the bytes per line
when using a particular format. This results in the correct stride being
calculated even when the format is planar.
Signed-off-by: Garrett Wilson <g@floft.net>
bcm2835: camera: check for scene not being found
static analysis by cppcheck detected some potential NULL pointer
dereference issues:
[drivers/media/platform/bcm2835/controls.c:854]: (error) Possible null
pointer dereference: scene
(and lines 858, 859 too)
it is possible that scene is not found because of an invalue ctrl->val
and is therefore NULL and hence causing a null pointer dereference.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
bcm2835: memcpy port data to m rather than rmsg
static analysis by cppcheck detected a memcpy to rmsg which is
not actually initialized at that point. The memcpy should be copying
to variable m instead.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
BCM2835-V4L2: Return buffers to videobuf2 on shutdown
https://github.com/raspberrypi/linux/issues/817
Fixes the kernel warning from videobuf2 as buffers
are now returned as they are being flushed on
stop_streaming.
squash: Fixup bcm2835-camera for changes in kernel 4.4 api
v4l2: Fix up driver to upstream timestamp changes
bcm2835-camera: fix a bug in computation of frame timestamp
Fixes#1318
Support booting without Device Tree.
Turn on USB power.
Load driver early because of lacking support for deferred probing
in many drivers.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Add module for accessing the mailbox property channel through
/dev/vcio. Was previously in bcm2708-vcio.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
i2c-bcm2708: fixed baudrate
Fixed issue where the wrong CDIV value was set for baudrates below 3815 Hz (for 250MHz bus clock).
In that case the computed CDIV value was more than 0xffff. However the CDIV register width is only 16 bits.
This resulted in incorrect setting of CDIV and higher baudrate than intended.
Example: 3500Hz -> CDIV=0x11704 -> CDIV(16bit)=0x1704 -> 42430Hz
After correction: 3500Hz -> CDIV=0x11704 -> CDIV(16bit)=0xffff -> 3815Hz
The correct baudrate is shown in the log after the cdiv > 0xffff correction.
Perform I2C combined transactions when possible
Perform I2C combined transactions whenever possible, within the
restrictions of the Broadcomm Serial Controller.
Disable DONE interrupt during TA poll
Prevent interrupt from being triggered if poll is missed and transfer
starts and finishes.
i2c: Make combined transactions optional and disabled by default
i2c: bcm2708: add device tree support
Add DT support to driver and add to .dtsi file.
Setup pins in .dts file.
i2c is disabled by default.
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
bcm2708: don't register i2c controllers when using DT
The devices for the i2c controllers are in the Device Tree.
Only register devices when not using DT.
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
I2C: Only register the I2C device for the current board revision
i2c_bcm2708: Fix clock reference counting
Fix grabbing lock from atomic context in i2c driver
2 main changes:
- check for timeouts in the bcm2708_bsc_setup function as indicated by this comment:
/* poll for transfer start bit (should only take 1-20 polls) */
This implies that the setup function can now fail so account for this everywhere it's called
- Removed the clk_get_rate call from inside the setup function as it locks a mutex and that's not ok since we call it from under a spin lock.
i2c-bcm2708: When using DT, leave the GPIO setup to pinctrl
i2c-bcm2708: Increase timeouts to allow larger transfers
Use the timeout value provided by the I2C_TIMEOUT ioctl when waiting
for completion. The default timeout is 1 second.
See: https://github.com/raspberrypi/linux/issues/260
i2c-bcm2708/BCM270X_DT: Add support for I2C2
The third I2C bus (I2C2) is normally reserved for HDMI use. Careless
use of this bus can break an attached display - use with caution.
It is recommended to disable accesses by VideoCore by setting
hdmi_ignore_edid=1 or hdmi_edid_file=1 in config.txt.
The interface is disabled by default - enable using the
i2c2_iknowwhatimdoing DT parameter.
bcm2708-spi: Don't use static pin configuration with DT
Also remove superfluous error checking - the SPI framework ensures the
validity of the chip_select value.
i2c-bcm2708: Remove non-DT support
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Set the BSC_CLKT clock streching timeout to 35ms as per SMBus specs.
BCM270x: Move thermal sensor to Device Tree
Add Device Tree support to bcm2835-thermal driver.
Add thermal sensor device to Device Tree.
Don't add platform device when booting in DT mode.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
lirc_rpi: Use read_current_timer to determine transmitter delay. Thanks to jjmz and others
See: https://github.com/raspberrypi/linux/issues/525
lirc: Remove restriction on gpio pins that can be used with lirc
Compute Module, for example could use different pins
lirc_rpi: Add parameter to specify input pin pull
Depending on the connected IR circuitry it might be desirable to change the
gpios internal pull from it pull-down default behaviour. Add a module
parameter to allow the user to set it explicitly.
Signed-off-by: Julian Scheel <julian@jusst.de>
lirc-rpi: Use the higher-level irq control functions
This module used to access the irq_chip methods of the
gpio controller directly, rather than going through the
standard enable_irq/irq_set_irq_type functions. This
caused problems on pinctrl-bcm2835 which only implements
the irq_enable/disable methods and not irq_unmask/mask.
lirc-rpi: Correct the interrupt usage
1) Correct the use of enable_irq (i.e. don't call it so often)
2) Correct the shutdown sequence.
3) Avoid a bcm2708_gpio driver quirk by setting the irq flags earlier
lirc-rpi: use getnstimeofday instead of read_current_timer
read_current_timer isn't guaranteed to return values in
microseconds, and indeed it doesn't on a Pi2.
Issue: linux#827
lirc-rpi: Add device tree support, and a suitable overlay
The overlay supports DT parameters that match the old module
parameters, except that gpio_in_pull should be set using the
strings "up", "down" or "off".
lirc-rpi: Also support pinctrl-bcm2835 in non-DT mode
Add experimental support for the VideoCore shared memory service.
This allows user processes to allocate memory from VideoCore's
GPU relocatable heap and mmap the buffers. Additionally, the memory
handles can passed to other VideoCore services such as MMAL, OpenMax
and DispmanX
TODO
* This driver was originally released for BCM28155 which has a different
cache architecture to BCM2835. Consequently, in this release only
uncached mappings are supported. However, there's no fundamental
reason which cached mappings cannot be support or BCM2835
* More refactoring is required to remove the typedefs.
* Re-enable the some of the commented out debug-fs statistics which were
disabled when migrating code from proc-fs.
* There's a lot of code to support sharing of VCSM in order to support
Android. This could probably done more cleanly or perhaps just
removed.
Signed-off-by: Tim Gover <timgover@gmail.com>
config: Disable VC_SM for now to fix hang with cutdown kernel
vcsm: Use boolean as it cannot be built as module
On building the bcm_vc_sm as a module we get the following error:
v7_dma_flush_range and do_munmap are undefined in vc-sm.ko.
Fix by making it not an option to build as module
vcsm: Add ioctl for custom cache flushing
vc-sm: Move headers out of arch directory
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: popcornmix <popcornmix@gmail.com>
BCM270x: Move vc_mem
Make the vc_mem module available for ARCH_BCM2835 by moving it.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: popcornmix <popcornmix@gmail.com>
vchiq: create_pagelist copes with vmalloc memory
Signed-off-by: Daniel Stone <daniels@collabora.com>
vchiq: fix the shim message release
Signed-off-by: Daniel Stone <daniels@collabora.com>
vchiq: export additional symbols
Signed-off-by: Daniel Stone <daniels@collabora.com>
VCHIQ: Make service closure fully synchronous (drv)
This is one half of a two-part patch, the other half of which is to
the vchiq_lib user library. With these patches, calls to
vchiq_close_service and vchiq_remove_service won't return until any
associated callbacks have been delivered to the callback thread.
VCHIQ: Add per-service tracing
The new service option VCHIQ_SERVICE_OPTION_TRACE is a boolean that
toggles tracing for the specified service.
This commit also introduces vchi_service_set_option and the associated
option VCHI_SERVICE_OPTION_TRACE.
vchiq: Make the synchronous-CLOSE logic more tolerant
vchiq: Move logging control into debugfs
vchiq: Take care of a corner case tickled by VCSM
Closing a connection that isn't fully open requires care, since one
side does not know the other side's port number. Code was present to
handle the case where a CLOSE is sent immediately after an OPEN, i.e.
before the OPENACK has been received, but this was incorrectly being
used when an OPEN from a client using port 0 was rejected.
(In the observed failure, the host was attempting to use the VCSM
service, which isn't present in the 'cutdown' firmware. The failure
was intermittent because sometimes the keepalive service would
grab port 0.)
This case can be distinguished because the client's remoteport will
still be VCHIQ_PORT_FREE, and the srvstate will be OPENING. Either
condition is sufficient to differentiate it from the special case
described above.
vchiq: Avoid high load when blocked and unkillable
vchiq: Include SIGSTOP and SIGCONT in list of signals not-masked by vchiq to allow gdb to work
vchiq_arm: Complete support for SYNCHRONOUS mode
vchiq: Remove inline from suspend/resume
vchiq: Allocation does not need to be atomic
vchiq: Fix wrong condition check
The log level is checked from within the log call. Remove the check in the call.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
BCM270x: Add vchiq device to platform file and Device Tree
Prepare to turn the vchiq module into a driver.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2708: vchiq: Add Device Tree support
Turn vchiq into a driver and stop hardcoding resources.
Use devm_* functions in probe path to simplify cleanup.
A global variable is used to hold the register address. This is done
to keep this patch as small as possible.
Also make available on ARCH_BCM2835.
Based on work by Lubomir Rintel.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
vchiq: Change logging level for inbound data
vchiq_arm: Two cacheing fixes
1) Make fragment size vary with cache line size
Without this patch, non-cache-line-aligned transfers may corrupt
(or be corrupted by) adjacent data structures.
Both ARM and VC need to be updated to enable this feature. This is
ensured by having the loader apply a new DT parameter -
cache-line-size. The existence of this parameter guarantees that the
kernel is capable, and the parameter will only be modified from the
safe default if the loader is capable.
2) Flush/invalidate vmalloc'd memory, and invalidate after reads
vchiq: fix NULL pointer dereference when closing driver
The following code run as root will cause a null pointer dereference oops:
int fd = open("/dev/vc-cma", O_RDONLY);
if (fd < 0)
err(1, "open failed");
(void)close(fd);
[ 1704.877721] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[ 1704.877725] pgd = b899c000
[ 1704.877736] [00000000] *pgd=37fab831, *pte=00000000, *ppte=00000000
[ 1704.877748] Internal error: Oops: 817 [#1] PREEMPT SMP ARM
[ 1704.877765] Modules linked in: evdev i2c_bcm2708 uio_pdrv_genirq uio
[ 1704.877774] CPU: 2 PID: 3656 Comm: stress-ng-fstat Not tainted 3.19.1-12-generic-bcm2709 #12-Ubuntu
[ 1704.877777] Hardware name: BCM2709
[ 1704.877783] task: b8ab9b00 ti: b7e68000 task.ti: b7e68000
[ 1704.877798] PC is at __down_interruptible+0x50/0xec
[ 1704.877806] LR is at down_interruptible+0x5c/0x68
[ 1704.877813] pc : [<80630ee8>] lr : [<800704b0>] psr: 60080093
sp : b7e69e50 ip : b7e69e88 fp : b7e69e84
[ 1704.877817] r10: b88123c8 r9 : 00000010 r8 : 00000001
[ 1704.877822] r7 : b8ab9b00 r6 : 7fffffff r5 : 80a1cc34 r4 : 80a1cc34
[ 1704.877826] r3 : b7e69e50 r2 : 00000000 r1 : 00000000 r0 : 80a1cc34
[ 1704.877833] Flags: nZCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment user
[ 1704.877838] Control: 10c5387d Table: 3899c06a DAC: 00000015
[ 1704.877843] Process do-oops (pid: 3656, stack limit = 0xb7e68238)
[ 1704.877848] Stack: (0xb7e69e50 to 0xb7e6a000)
[ 1704.877856] 9e40: 80a1cc3c 00000000 00000010 b88123c8
[ 1704.877865] 9e60: b7e69e84 80a1cc34 fff9fee9 ffffffff b7e68000 00000009 b7e69ea4 b7e69e88
[ 1704.877874] 9e80: 800704b0 80630ea4 fff9fee9 60080013 80a1cc28 fff9fee9 b7e69edc b7e69ea8
[ 1704.877884] 9ea0: 8040f558 80070460 fff9fee9 ffffffff 00000000 00000000 00000009 80a1cb7c
[ 1704.877893] 9ec0: 00000000 80a1cb7c 00000000 00000010 b7e69ef4 b7e69ee0 803e1ba4 8040f514
[ 1704.877902] 9ee0: 00000e48 80a1cb7c b7e69f14 b7e69ef8 803e1c9c 803e1b74 b88123c0 b92acb18
[ 1704.877911] 9f00: b8812790 b8d815d8 b7e69f24 b7e69f18 803e2250 803e1bc8 b7e69f5c b7e69f28
[ 1704.877921] 9f20: 80167bac 803e222c 00000000 00000000 b7e69f54 b8ab9ffc 00000000 8098c794
[ 1704.877930] 9f40: b8ab9b00 8000efc4 b7e68000 00000000 b7e69f6c b7e69f60 80167d6c 80167b28
[ 1704.877939] 9f60: b7e69f8c b7e69f70 80047d38 80167d60 b7e68000 b7e68010 8000efc4 b7e69fb0
[ 1704.877949] 9f80: b7e69fac b7e69f90 80012820 80047c84 01155490 011549a8 00000001 00000006
[ 1704.877957] 9fa0: 00000000 b7e69fb0 8000ee5c 80012790 00000000 353d8c0f 7efc4308 00000000
[ 1704.877966] 9fc0: 01155490 011549a8 00000001 00000006 00000000 00000000 76cf3ba0 00000003
[ 1704.877975] 9fe0: 00000000 7efc42e4 0002272f 76e2ed66 60080030 00000003 00000000 00000000
[ 1704.877998] [<80630ee8>] (__down_interruptible) from [<800704b0>] (down_interruptible+0x5c/0x68)
[ 1704.878015] [<800704b0>] (down_interruptible) from [<8040f558>] (vchiu_queue_push+0x50/0xd8)
[ 1704.878032] [<8040f558>] (vchiu_queue_push) from [<803e1ba4>] (send_worker_msg+0x3c/0x54)
[ 1704.878045] [<803e1ba4>] (send_worker_msg) from [<803e1c9c>] (vc_cma_set_reserve+0xe0/0x1c4)
[ 1704.878057] [<803e1c9c>] (vc_cma_set_reserve) from [<803e2250>] (vc_cma_release+0x30/0x38)
[ 1704.878069] [<803e2250>] (vc_cma_release) from [<80167bac>] (__fput+0x90/0x1e0)
[ 1704.878082] [<80167bac>] (__fput) from [<80167d6c>] (____fput+0x18/0x1c)
[ 1704.878094] [<80167d6c>] (____fput) from [<80047d38>] (task_work_run+0xc0/0xf8)
[ 1704.878109] [<80047d38>] (task_work_run) from [<80012820>] (do_work_pending+0x9c/0xc4)
[ 1704.878123] [<80012820>] (do_work_pending) from [<8000ee5c>] (work_pending+0xc/0x20)
[ 1704.878133] Code: e50b1034 e3a01000 e50b2030 e580300c (e5823000)
..the fix is to ensure that we have actually initialized the queue before we attempt
to push any items onto it. This occurs if we do an open() followed by a close() without
any activity in between.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
vchiq_arm: Sort out the vmalloc case
See: https://github.com/raspberrypi/linux/issues/1055
vchiq: hack: Add include depecated dma include file
vchiq_arm: Tweak the logging output
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
vchiq_arm: Access the dequeue_pending flag locked
Reading through this code looking for another problem (now found in userland)
the use of dequeue_pending outside a lock didn't seem safe.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
vchiq_arm: Service callbacks must not fail
Service callbacks are not allowed to return an error. The internal callback
that delivers events and messages to user tasks does not enqueue them if
the service is closing, but this is not an error and should not be
reported as such.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: popcornmix <popcornmix@gmail.com>
alsa: add mmap support and some cleanups to bcm2835 ALSA driver
snd-bcm2835: Add support for spdif/hdmi passthrough
This adds a dedicated subdevice which can be used for passthrough of non-audio
formats (ie encoded a52) through the hdmi audio link. In addition to this
driver extension an appropriate card config is required to make alsa-lib
support the AES parameters for this device.
snd-bcm2708: Add mutex, improve logging
Fix for ALSA driver crash
Avoids an issue when closing and opening vchiq where a message can arrive before service handle has been written
alsa: reduce severity of expected warning message
snd-bcm2708: Fix dmesg spam for non-error case
alsa: Ensure mutexes are released through error paths
alsa: Make interrupted close paths quieter
BCM270x: Add onboard sound device to Device Tree
Add Device Tree support to alsa driver.
Add device to Device Tree.
Don't add platform devices when booting in DT mode.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: popcornmix <popcornmix@gmail.com>
vc_cma: Make the vc_cma area the default contiguous DMA area
vc_cma: Provide empty functions when module is not built
Providing empty functions saves the users from guarding the
function call with an #if clause.
Move __init markings from prototypes to functions.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM2835 has two SD card interfaces. This driver uses the other one.
bcm2835-sdhost: Error handling fix, and code clarification
bcm2835-sdhost: Adding overclocking option
Allow a different clock speed to be substitued for a requested 50MHz.
This option is exposed using the "overclock_50" DT parameter.
Note that the sdhost interface is restricted to integer divisions of
core_freq, and the highest sensible option for a core_freq of 250MHz
is 84 (250/3 = 83.3MHz), the next being 125 (250/2) which is much too
high.
Use at your own risk.
bcm2835-sdhost: Round up the overclock, so 62 works for 62.5Mhz
Also only warn once for each overclock setting.
bcm2835-sdhost: Improve error handling and recovery
1) Expose the hw_reset method to the MMC framework, removing many
internal calls by the driver.
2) Reduce overclock setting on error.
3) Increase timeout to cope with high capacity cards.
4) Add properties and parameters to control pio_limit and debug.
5) Reduce messages at probe time.
bcm2835-sdhost: Further improve overclock back-off
bcm2835-sdhost: Clear HBLC for PIO mode
Also update pio_limit default in overlay README.
bcm2835-sdhost: Add the ERASE capability
See: https://github.com/raspberrypi/linux/issues/1076
bcm2835-sdhost: Ignore CRC7 for MMC CMD1
It seems that the sdhost interface returns CRC7 errors for CMD1,
which is the MMC-specific SEND_OP_COND. Returning these errors to
the MMC layer causes a downward spiral, but ignoring them seems
to be harmless.
bcm2835-mmc/sdhost: Remove ARCH_BCM2835 differences
The bcm2835-mmc driver (and -sdhost driver that copied from it)
contains code to handle SDIO interrupts in a threaded interrupt
handler rather than waking the MMC framework thread. The change
follows a patch from Russell King that adds the facility as the
preferred way of working.
However, the new code path is only present in ARCH_BCM2835
builds, which I have taken to be a way of testing the waters
rather than making the change across the board; I can't see
any technical reason why it wouldn't be enabled for MACH_BCM270X
builds. So this patch standardises on the ARCH_BCM2835 code,
removing the old code paths.
bcm2835-sdhost: Don't log timeout errors unless debug=1
The MMC card-discovery process generates timeouts. This is
expected behaviour, so reporting it to the user serves no purpose.
Suppress the reporting of timeout errors unless the debug flag
is on.
bcm2835-sdhost: Add workaround for odd behaviour on some cards
For reasons not understood, the sdhost driver fails when reading
sectors very near the end of some SD cards. The problem could
be related to the similar issue that reading the final sector
of any card as part of a multiple read never completes, and the
workaround is an extension of the mechanism introduced to solve
that problem which ensures those sectors are always read singly.
bcm2835-sdhost: Major revision
This is a significant revision of the bcm2835-sdhost driver. It
improves on the original in a number of ways:
1) Through the use of CMD23 for reads it appears to avoid problems
reading some sectors on certain high speed cards.
2) Better atomicity to prevent crashes.
3) Higher performance.
4) Activity logging included, for easier diagnosis in the event
of a problem.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Restore ATOMIC flag to PIO sg mapping
Allocation problems have been seen in a wireless driver, and
this is the only change which might have been responsible.
SQUASH: bcm2835-sdhost: Only claim one DMA channel
With both MMC controllers enabled there are few DMA channels left. The
bcm2835-sdhost driver only uses DMA in one direction at a time, so it
doesn't need to claim two channels.
See: https://github.com/raspberrypi/linux/issues/1327
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Workaround for "slow" sectors
Some cards have been seen to cause timeouts after certain sectors are
read. This workaround enforces a minimum delay between the stop after
reading one of those sectors and a subsequent data command.
Using CMD23 (SET_BLOCK_COUNT) avoids this problem, so good cards will
not be penalised by this workaround.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
mmc: Disable CMD23 transfers on all cards
Pending wire-level investigation of these types of transfers
and associated errors on bcm2835-mmc, disable for now. Fallback of
CMD18/CMD25 transfers will be used automatically by the MMC layer.
Reported/Tested-by: Gellert Weisz <gellert@raspberrypi.org>
mmc: bcm2835-mmc: enable DT support for all architectures
Both ARCH_BCM2835 and ARCH_BCM270x are built with OF now.
Enable Device Tree support for all architectures.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
mmc: bcm2835-mmc: fix probe error handling
Probe error handling is broken in several places.
Simplify error handling by using device managed functions.
Replace pr_{err,info} with dev_{err,info}.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2835-mmc: Add locks when accessing sdhost registers
bcm2835-mmc: Add range of debug options for slowing things down
bcm2835-mmc: Add option to disable some delays
bcm2835-mmc: Add option to disable MMC_QUIRK_BLK_NO_CMD23
bcm2835-mmc: Default to disabling MMC_QUIRK_BLK_NO_CMD23
bcm2835-mmc: Adding overclocking option
Allow a different clock speed to be substitued for a requested 50MHz.
This option is exposed using the "overclock_50" DT parameter.
Note that the mmc interface is restricted to EVEN integer divisions of
250MHz, and the highest sensible option is 63 (250/4 = 62.5), the
next being 125 (250/2) which is much too high.
Use at your own risk.
bcm2835-mmc: Round up the overclock, so 62 works for 62.5Mhz
Also only warn once for each overclock setting.
mmc: bcm2835-mmc: Make available on ARCH_BCM2835
Make the bcm2835-mmc driver available for use on ARCH_BCM2835.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270x_DT: add bcm2835-mmc entry
Add Device Tree entry for bcm2835-mmc.
In non-DT mode, don't add the device in the board file.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2835-mmc: Don't overwrite MMC capabilities from DT
bcm2835-mmc: Don't override bus width capabilities from devicetree
Take out the force setting of the MMC_CAP_4_BIT_DATA host capability
so that the result read from devicetree via mmc_of_parse() is
preserved.
bcm2835-mmc: Only claim one DMA channel
With both MMC controllers enabled there are few DMA channels left. The
bcm2835-mmc driver only uses DMA in one direction at a time, so it
doesn't need to claim two channels.
See: https://github.com/raspberrypi/linux/issues/1327
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Add support for DMA controller of BCM2708 as used in the Raspberry Pi.
Currently it only supports cyclic DMA.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
dmaengine: expand functionality by supporting scatter/gather transfers sdhci-bcm2708 and dma.c: fix for LITE channels
DMA: fix cyclic LITE length overflow bug
dmaengine: bcm2708: Remove chancnt affectations
Mirror bcm2835-dma.c commit 9eba5536a7:
chancnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: overwrite dreq only if it is not set
dreq is set when the DMA channel is fetched from Device Tree.
slave_id is set using dmaengine_slave_config().
Only overwrite dreq with slave_id if it is not set.
dreq/slave_id in the cyclic DMA case is not touched, because I don't
have hardware to test with.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: do device registration in the board file
Don't register the device in the driver. Do it in the board file.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: don't restrict DT support to ARCH_BCM2835
Both ARCH_BCM2835 and ARCH_BCM270x are built with OF now.
Add Device Tree support to the non ARCH_BCM2835 case.
Use the same driver name regardless of architecture.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270x_DT: add bcm2835-dma entry
Add Device Tree entry for bcm2835-dma.
The entry doesn't contain any resources since they are handled
by the arch/arm/mach-bcm270x/dma.c driver.
In non-DT mode, don't add the device in the board file.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2708-dmaengine: Add debug options
BCM270x: Add memory and irq resources to dmaengine device and DT
Prepare for merging of the legacy DMA API arch driver dma.c
with bcm2708-dmaengine by adding memory and irq resources both
to platform file device and Device Tree node.
Don't use BCM_DMAMAN_DRIVER_NAME so we don't have to include mach/dma.h
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: Merge with arch dma.c driver and disable dma.c
Merge the legacy DMA API driver with bcm2708-dmaengine.
This is done so we can use bcm2708_fb on ARCH_BCM2835 (mailbox
driver is also needed).
Changes to the dma.c code:
- Use BIT() macro.
- Cutdown some comments to one line.
- Add mutex to vc_dmaman and use this, since the dev lock is locked
during probing of the engine part.
- Add global g_dmaman variable since drvdata is used by the engine part.
- Restructure for readability:
vc_dmaman_chan_alloc()
vc_dmaman_chan_free()
bcm_dma_chan_free()
- Restructure bcm_dma_chan_alloc() to simplify error handling.
- Use device irq resources instead of hardcoded bcm_dma_irqs table.
- Remove dev_dmaman_register() and code it directly.
- Remove dev_dmaman_deregister() and code it directly.
- Simplify bcm_dmaman_probe() using devm_* functions.
- Get dmachans from DT if available.
- Keep 'dma.dmachans' module argument name for backwards compatibility.
Make it available on ARCH_BCM2835 as well.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: set residue_granularity field
bcm2708-dmaengine supports residue reporting at burst level
but didn't report this via the residue_granularity field.
Without this field set properly we get playback issues with I2S cards.
dmaengine: bcm2708-dmaengine: Fix memory leak when stopping a running transfer
bcm2708-dmaengine: Use more DMA channels (but not 12)
1) Only the bcm2708_fb drivers uses the legacy DMA API, and
it requires a BULK-capable channel, so all other types
(FAST, NORMAL and LITE) can be made available to the regular
DMA API.
2) DMA channels 11-14 share an interrupt. The driver can't
handle this, so don't use channels 12-14 (12 was used, probably
because it appears to have an interrupt, but in reality that
interrupt is for activity on ANY channel). This may explain
a lockup encountered when running out of DMA channels.
The combined effect of this patch is to leave 7 DMA channels
available + channel 0 for bcm2708_fb via the legacy API.
See: https://github.com/raspberrypi/linux/issues/1110https://github.com/raspberrypi/linux/issues/1108
dmaengine: bcm2708: Make legacy API available for bcm2835-dma
bcm2708_fb uses the legacy DMA API, so in order to start using
bcm2835-dma, bcm2835-dma has to support the legacy API. Make this
possible by exporting bcm_dmaman_probe() and bcm_dmaman_remove().
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: Change DT compatible string
Both bcm2835-dma and bcm2708-dmaengine have the same compatible string.
So change compatible to "brcm,bcm2708-dma".
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: Remove driver but keep legacy API
Dropping non-DT support means we don't need this driver,
but we still need the legacy DMA API.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: popcornmix <popcornmix@gmail.com>
bcm2708_fb : Implement blanking support using the mailbox property interface
bcm2708_fb: Add pan and vsync controls
bcm2708_fb: DMA acceleration for fb_copyarea
Based on http://www.raspberrypi.org/phpBB3/viewtopic.php?p=62425#p62425
Also used Simon's dmaer_master module as a reference for tweaking DMA
settings for better performance.
For now busylooping only. IRQ support might be added later.
With non-overclocked Raspberry Pi, the performance is ~360 MB/s
for simple copy or ~260 MB/s for two-pass copy (used when dragging
windows to the right).
In the case of using DMA channel 0, the performance improves
to ~440 MB/s.
For comparison, VFP optimized CPU copy can only do ~114 MB/s in
the same conditions (hindered by reading uncached source buffer).
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
bcm2708_fb: report number of dma copies
Add a counter (exported via debugfs) reporting the
number of dma copies that the framebuffer driver
has done, in order to help evaluate different
optimization strategies.
Signed-off-by: Luke Diamand <luked@broadcom.com>
bcm2708_fb: use IRQ for DMA copies
The copyarea ioctl() uses DMA to speed things along. This
was busy-waiting for completion. This change supports using
an interrupt instead for larger transfers. For small
transfers, busy-waiting is still likely to be faster.
Signed-off-by: Luke Diamand <luke@diamand.org>
bcm2708: Make ioctl logging quieter
video: fbdev: bcm2708_fb: Don't panic on error
No need to panic the kernel if the video driver fails.
Just print a message and return an error.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
fbdev: bcm2708_fb: Add ARCH_BCM2835 support
Add Device Tree support.
Pass the device to dma_alloc_coherent() in order to get the
correct bus address on ARCH_BCM2835.
Use the new DMA legacy API header file.
Including <mach/platform.h> is not necessary.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270x_DT: Add bcm2708-fb device
Add bcm2708-fb to Device Tree and don't add the
platform device when booting in DT mode.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: popcornmix <popcornmix@gmail.com>
usb: dwc: fix lockdep false positive
Signed-off-by: Kari Suvanto <karis79@gmail.com>
usb: dwc: fix inconsistent lock state
Signed-off-by: Kari Suvanto <karis79@gmail.com>
Add FIQ patch to dwc_otg driver. Enable with dwc_otg.fiq_fix_enable=1. Should give about 10% more ARM performance.
Thanks to Gordon and Costas
Avoid dynamic memory allocation for channel lock in USB driver. Thanks ddv2005.
Add NAK holdoff scheme. Enabled by default, disable with dwc_otg.nak_holdoff_enable=0. Thanks gsh
Make sure we wait for the reset to finish
dwc_otg: fix bug in dwc_otg_hcd.c resulting in silent kernel
memory corruption, escalating to OOPS under high USB load.
dwc_otg: Fix unsafe access of QTD during URB enqueue
In dwc_otg_hcd_urb_enqueue during qtd creation, it was possible that the
transaction could complete almost immediately after the qtd was assigned
to a host channel during URB enqueue, which meant the qtd pointer was no
longer valid having been completed and removed. Usually, this resulted in
an OOPS during URB submission. By predetermining whether transactions
need to be queued or not, this unsafe pointer access is avoided.
This bug was only evident on the Pi model A where a device was attached
that had no periodic endpoints (e.g. USB pendrive or some wlan devices).
dwc_otg: Fix incorrect URB allocation error handling
If the memory allocation for a dwc_otg_urb failed, the kernel would OOPS
because for some reason a member of the *unallocated* struct was set to
zero. Error handling changed to fail correctly.
dwc_otg: fix potential use-after-free case in interrupt handler
If a transaction had previously aborted, certain interrupts are
enabled to track error counts and reset where necessary. On IN
endpoints the host generates an ACK interrupt near-simultaneously
with completion of transfer. In the case where this transfer had
previously had an error, this results in a use-after-free on
the QTD memory space with a 1-byte length being overwritten to
0x00.
dwc_otg: add handling of SPLIT transaction data toggle errors
Previously a data toggle error on packets from a USB1.1 device behind
a TT would result in the Pi locking up as the driver never handled
the associated interrupt. Patch adds basic retry mechanism and
interrupt acknowledgement to cater for either a chance toggle error or
for devices that have a broken initial toggle state (FT8U232/FT232BM).
dwc_otg: implement tasklet for returning URBs to usbcore hcd layer
The dwc_otg driver interrupt handler for transfer completion will spend
a very long time with interrupts disabled when a URB is completed -
this is because usb_hcd_giveback_urb is called from within the handler
which for a USB device driver with complicated processing (e.g. webcam)
will take an exorbitant amount of time to complete. This results in
missed completion interrupts for other USB packets which lead to them
being dropped due to microframe overruns.
This patch splits returning the URB to the usb hcd layer into a
high-priority tasklet. This will have most benefit for isochronous IN
transfers but will also have incidental benefit where multiple periodic
devices are active at once.
dwc_otg: fix NAK holdoff and allow on split transactions only
This corrects a bug where if a single active non-periodic endpoint
had at least one transaction in its qh, on frnum == MAX_FRNUM the qh
would get skipped and never get queued again. This would result in
a silent device until error detection (automatic or otherwise) would
either reset the device or flush and requeue the URBs.
Additionally the NAK holdoff was enabled for all transactions - this
would potentially stall a HS endpoint for 1ms if a previous error state
enabled this interrupt and the next response was a NAK. Fix so that
only split transactions get held off.
dwc_otg: Call usb_hcd_unlink_urb_from_ep with lock held in completion handler
usb_hcd_unlink_urb_from_ep must be called with the HCD lock held. Calling it
asynchronously in the tasklet was not safe (regression in
c4564d4a1a).
This change unlinks it from the endpoint prior to queueing it for handling in
the tasklet, and also adds a check to ensure the urb is OK to be unlinked
before doing so.
NULL pointer dereference kernel oopses had been observed in usb_hcd_giveback_urb
when a USB device was unplugged/replugged during data transfer. This effect
was reproduced using automated USB port power control, hundreds of replug
events were performed during active transfers to confirm that the problem was
eliminated.
USB fix using a FIQ to implement split transactions
This commit adds a FIQ implementaion that schedules
the split transactions using a FIQ so we don't get
held off by the interrupt latency of Linux
dwc_otg: fix device attributes and avoid kernel warnings on boot
dcw_otg: avoid logging function that can cause panics
See: https://github.com/raspberrypi/firmware/issues/21
Thanks to cleverca22 for fix
dwc_otg: mask correct interrupts after transaction error recovery
The dwc_otg driver will unmask certain interrupts on a transaction
that previously halted in the error state in order to reset the
QTD error count. The various fine-grained interrupt handlers do not
consider that other interrupts besides themselves were unmasked.
By disabling the two other interrupts only ever enabled in DMA mode
for this purpose, we can avoid unnecessary function calls in the
IRQ handler. This will also prevent an unneccesary FIQ interrupt
from being generated if the FIQ is enabled.
dwc_otg: fiq: prevent FIQ thrash and incorrect state passing to IRQ
In the case of a transaction to a device that had previously aborted
due to an error, several interrupts are enabled to reset the error
count when a device responds. This has the side-effect of making the
FIQ thrash because the hardware will generate multiple instances of
a NAK on an IN bulk/interrupt endpoint and multiple instances of ACK
on an OUT bulk/interrupt endpoint. Make the FIQ mask and clear the
associated interrupts.
Additionally, on non-split transactions make sure that only unmasked
interrupts are cleared. This caused a hard-to-trigger but serious
race condition when you had the combination of an endpoint awaiting
error recovery and a transaction completed on an endpoint - due to
the sequencing and timing of interrupts generated by the dwc_otg core,
it was possible to confuse the IRQ handler.
Fix function tracing
dwc_otg: whitespace cleanup in dwc_otg_urb_enqueue
dwc_otg: prevent OOPSes during device disconnects
The dwc_otg_urb_enqueue function is thread-unsafe. In particular the
access of urb->hcpriv, usb_hcd_link_urb_to_ep, dwc_otg_urb->qtd and
friends does not occur within a critical section and so if a device
was unplugged during activity there was a high chance that the
usbcore hub_thread would try to disable the endpoint with partially-
formed entries in the URB queue. This would result in BUG() or null
pointer dereferences.
Fix so that access of urb->hcpriv, enqueuing to the hardware and
adding to usbcore endpoint URB lists is contained within a single
critical section.
dwc_otg: prevent BUG() in TT allocation if hub address is > 16
A fixed-size array is used to track TT allocation. This was
previously set to 16 which caused a crash because
dwc_otg_hcd_allocate_port would read past the end of the array.
This was hit if a hub was plugged in which enumerated as addr > 16,
due to previous device resets or unplugs.
Also add #ifdef FIQ_DEBUG around hcd->hub_port_alloc[], which grows
to a large size if 128 hub addresses are supported. This field is
for debug only for tracking which frame an allocate happened in.
dwc_otg: make channel halts with unknown state less damaging
If the IRQ received a channel halt interrupt through the FIQ
with no other bits set, the IRQ would not release the host
channel and never complete the URB.
Add catchall handling to treat as a transaction error and retry.
dwc_otg: fiq_split: use TTs with more granularity
This fixes certain issues with split transaction scheduling.
- Isochronous multi-packet OUT transactions now hog the TT until
they are completed - this prevents hubs aborting transactions
if they get a periodic start-split out-of-order
- Don't perform TT allocation on non-periodic endpoints - this
allows simultaneous use of the TT's bulk/control and periodic
transaction buffers
This commit will mainly affect USB audio playback.
dwc_otg: fix potential sleep while atomic during urb enqueue
Fixes a regression introduced with eb1b482a. Kmalloc called from
dwc_otg_hcd_qtd_add / dwc_otg_hcd_qtd_create did not always have
the GPF_ATOMIC flag set. Force this flag when inside the larger
critical section.
dwc_otg: make fiq_split_enable imply fiq_fix_enable
Failing to set up the FIQ correctly would result in
"IRQ 32: nobody cared" errors in dmesg.
dwc_otg: prevent crashes on host port disconnects
Fix several issues resulting in crashes or inconsistent state
if a Model A root port was disconnected.
- Clean up queue heads properly in kill_urbs_in_qh_list by
removing the empty QHs from the schedule lists
- Set the halt status properly to prevent IRQ handlers from
using freed memory
- Add fiq_split related cleanup for saved registers
- Make microframe scheduling reclaim host channels if
active during a disconnect
- Abort URBs with -ESHUTDOWN status response, informing
device drivers so they respond in a more correct fashion
and don't try to resubmit URBs
- Prevent IRQ handlers from attempting to handle channel
interrupts if the associated URB was dequeued (and the
driver state was cleared)
dwc_otg: prevent leaking URBs during enqueue
A dwc_otg_urb would get leaked if the HCD enqueue function
failed for any reason. Free the URB at the appropriate points.
dwc_otg: Enable NAK holdoff for control split transactions
Certain low-speed devices take a very long time to complete a
data or status stage of a control transaction, producing NAK
responses until they complete internal processing - the USB2.0
spec limit is up to 500mS. This causes the same type of interrupt
storm as seen with USB-serial dongles prior to c8edb238.
In certain circumstances, usually while booting, this interrupt
storm could cause SD card timeouts.
dwc_otg: Fix for occasional lockup on boot when doing a USB reset
dwc_otg: Don't issue traffic to LS devices in FS mode
Issuing low-speed packets when the root port is in full-speed mode
causes the root port to stop responding. Explicitly fail when
enqueuing URBs to a LS endpoint on a FS bus.
Fix ARM architecture issue with local_irq_restore()
If local_fiq_enable() is called before a local_irq_restore(flags) where
the flags variable has the F bit set, the FIQ will be erroneously disabled.
Fixup arch_local_irq_restore to avoid trampling the F bit in CPSR.
Also fix some of the hacks previously implemented for previous dwc_otg
incarnations.
dwc_otg: fiq_fsm: Base commit for driver rewrite
This commit removes the previous FIQ fixes entirely and adds fiq_fsm.
This rewrite features much more complete support for split transactions
and takes into account several OTG hardware bugs. High-speed
isochronous transactions are also capable of being performed by fiq_fsm.
All driver options have been removed and replaced with:
- dwc_otg.fiq_enable (bool)
- dwc_otg.fiq_fsm_enable (bool)
- dwc_otg.fiq_fsm_mask (bitmask)
- dwc_otg.nak_holdoff (unsigned int)
Defaults are specified such that fiq_fsm behaves similarly to the
previously implemented FIQ fixes.
fiq_fsm: Push error recovery into the FIQ when fiq_fsm is used
If the transfer associated with a QTD failed due to a bus error, the HCD
would retry the transfer up to 3 times (implementing the USB2.0
three-strikes retry in software).
Due to the masking mechanism used by fiq_fsm, it is only possible to pass
a single interrupt through to the HCD per-transfer.
In this instance host channels would fall off the radar because the error
reset would function, but the subsequent channel halt would be lost.
Push the error count reset into the FIQ handler.
fiq_fsm: Implement timeout mechanism
For full-speed endpoints with a large packet size, interrupt latency
runs the risk of the FIQ starting a transaction too late in a full-speed
frame. If the device is still transmitting data when EOF2 for the
downstream frame occurs, the hub will disable the port. This change is
not reflected in the hub status endpoint and the device becomes
unresponsive.
Prevent high-bandwidth transactions from being started too late in a
frame. The mechanism is not guaranteed: a combination of bit stuffing
and hub latency may still result in a device overrunning.
fiq_fsm: fix bounce buffer utilisation for Isochronous OUT
Multi-packet isochronous OUT transactions were subject to a few bounday
bugs. Fix them.
Audio playback is now much more robust: however, an issue stands with
devices that have adaptive sinks - ALSA plays samples too fast.
dwc_otg: Return full-speed frame numbers in HS mode
The frame counter increments on every *microframe* in high-speed mode.
Most device drivers expect this number to be in full-speed frames - this
caused considerable confusion to e.g. snd_usb_audio which uses the
frame counter to estimate the number of samples played.
fiq_fsm: save PID on completion of interrupt OUT transfers
Also add edge case handling for interrupt transports.
Note that for periodic split IN, data toggles are unimplemented in the
OTG host hardware - it unconditionally accepts any PID.
fiq_fsm: add missing case for fiq_fsm_tt_in_use()
Certain combinations of bitrate and endpoint activity could
result in a periodic transaction erroneously getting started
while the previous Isochronous OUT was still active.
fiq_fsm: clear hcintmsk for aborted transactions
Prevents the FIQ from erroneously handling interrupts
on a timed out channel.
fiq_fsm: enable by default
fiq_fsm: fix dequeues for non-periodic split transactions
If a dequeue happened between the SSPLIT and CSPLIT phases of the
transaction, the HCD would never receive an interrupt.
fiq_fsm: Disable by default
fiq_fsm: Handle HC babble errors
The HCTSIZ transfer size field raises a babble interrupt if
the counter wraps. Handle the resulting interrupt in this case.
dwc_otg: fix interrupt registration for fiq_enable=0
Additionally make the module parameter conditional for wherever
hcd->fiq_state is touched.
fiq_fsm: Enable by default
dwc_otg: Fix various issues with root port and transaction errors
Process the host port interrupts correctly (and don't trample them).
Root port hotplug now functional again.
Fix a few thinkos with the transaction error passthrough for fiq_fsm.
fiq_fsm: Implement hack for Split Interrupt transactions
Hubs aren't too picky about which endpoint we send Control type split
transactions to. By treating Interrupt transfers as Control, it is
possible to use the non-periodic queue in the OTG core as well as the
non-periodic FIFOs in the hub itself. This massively reduces the
microframe exclusivity/contention that periodic split transactions
otherwise have to enforce.
It goes without saying that this is a fairly egregious USB specification
violation, but it works.
Original idea by Hans Petter Selasky @ FreeBSD.org.
dwc_otg: FIQ support on SMP. Set up FIQ stack and handler on Core 0 only.
dwc_otg: introduce fiq_fsm_spin(un|)lock()
SMP safety for the FIQ relies on register read-modify write cycles being
completed in the correct order. Several places in the DWC code modify
registers also touched by the FIQ. Protect these by a bare-bones lock
mechanism.
This also makes it possible to run the FIQ and IRQ handlers on different
cores.
fiq_fsm: fix build on bcm2708 and bcm2709 platforms
dwc_otg: put some barriers back where they should be for UP
bcm2709/dwc_otg: Setup FIQ on core 1 if >1 core active
dwc_otg: fixup read-modify-write in critical paths
Be more careful about read-modify-write on registers that the FIQ
also touches.
Guard fiq_fsm_spin_lock with fiq_enable check
fiq_fsm: Falling out of the state machine isn't fatal
This edge case can be hit if the port is disabled while the FIQ is
in the middle of a transaction. Make the effects less severe.
Also get rid of the useless return value.
squash: dwc_otg: Allow to build without SMP
usb: core: make overcurrent messages more prominent
Hub overcurrent messages are more serious than "debug". Increase loglevel.
usb: dwc_otg: Don't use dma_to_virt()
Commit 6ce0d20 changes dma_to_virt() which breaks this driver.
Open code the old dma_to_virt() implementation to work around this.
Limit the use of __bus_to_virt() to cases where transfer_buffer_length
is set and transfer_buffer is not set. This is done to increase the
chance that this driver will also work on ARCH_BCM2835.
transfer_buffer should not be NULL if the length is set, but the
comment in the code indicates that there are situations where this
might happen. drivers/usb/isp1760/isp1760-hcd.c also has a similar
comment pointing to a possible: 'usb storage / SCSI bug'.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: Fix crash when fiq_enable=0
dwc_otg: fiq_fsm: Make high-speed isochronous strided transfers work properly
Certain low-bandwidth high-speed USB devices (specialist audio devices,
compressed-frame webcams) have packet intervals > 1 microframe.
Stride these transfers in the FIQ by using the start-of-frame interrupt
to restart the channel at the right time.
dwc_otg: Force host mode to fix incorrect compute module boards
dwc_otg: Add ARCH_BCM2835 support
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: Simplify FIQ irq number code
Dropping ATAGS means we can simplify the FIQ irq number code.
Also add error checking on the returned irq number.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: Remove duplicate gadget probe/unregister function
dwc_otg: Properly set the HFIR
Douglas Anderson reported:
According to the most up to date version of the dwc2 databook, the FRINT
field of the HFIR register should be programmed to:
* 125 us * (PHY clock freq for HS) - 1
* 1000 us * (PHY clock freq for FS/LS) - 1
This is opposed to older versions of the doc that claimed it should be:
* 125 us * (PHY clock freq for HS)
* 1000 us * (PHY clock freq for FS/LS)
and reported lower timing jitter on a USB analyser
dcw_otg: trim xfer length when buffer larger than allocated size is received
dwc_otg: Don't free qh align buffers in atomic context
dwc_otg: Enable the hack for Split Interrupt transactions by default
dwc_otg.fiq_fsm_mask=0xF has long been a suggestion for users with audio stutters or other USB bandwidth issues.
So far we are aware of many success stories but no failure caused by this setting.
Make it a default to learn more.
See: https://www.raspberrypi.org/forums/viewtopic.php?f=28&t=70437
Signed-off-by: popcornmix <popcornmix@gmail.com>
This is a hack until a proper solution is agreed upon.
Martin Sperl is doing some work in this area.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Transfers larger than 32k cause repeated clicking with I2S soundcards.
The exact reason is yet unknown, so limit to 32k as bcm2708-dmaengine
did as an intermediate fix.
Load driver early since at least bcm2708_fb doesn't support deferred
probing and even if it did, we don't want the video driver deferred.
Support the legacy DMA API which is needed by bcm2708_fb.
Don't mask out channel 2.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2835-dma supports residue reporting at burst level but didn't report
this via the residue_granularity field.
Without this field set properly we get playback issues with I2S cards.
[by HiassofT, taken from bcm2708-dmaengine]
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Add slave transfer capability to BCM2835 dmaengine driver.
This patch is pulled from the bcm2708-dmaengine driver in the
Raspberry Pi repo. The work was done by Gellert Weisz.
Tested using the bcm2835-mmc driver from the same repo.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Code ported from bcm2708-i2s driver in Raspberry Pi tree.
RPi commit 7ee829fd77 ("bcm2708-i2s:
Enable MMAP support via a DT property and overlay")
The i2s driver used to claim to support MMAP, but that feature was disabled
when some problems were found. Add the ability to enable this feature
through Device Tree, using the i2s-mmap overlay.
See: #1004
Signed-off-by: Matthias Reichl <hias@horus.com>
Code ported from bcm2708-i2s driver in Raspberry Pi tree.
RPi commit ba46b4935a ("ASoC: Add
support for BCM2708")
This driver adds support for digital audio (I2S)
for the BCM2708 SoC that is used by the
Raspberry Pi. External audio codecs can be
connected to the Raspberry Pi via P5 header.
It relies on cyclic DMA engine support for BCM2708.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
Signed-off-by: Matthias Reichl <hias@horus.com>
Code ported from bcm2708-i2s driver in Raspberry Pi tree.
RPi commit fd7d7a3dbe ("bcm2708:
Eliminate i2s debugfs directory error")
Qualify the two regmap ranges uses by bcm2708-i2s ('-i2s' and '-clk')
to avoid the name clash when registering debugfs entries.
Signed-off-by: Matthias Reichl <hias@horus.com>
Code ported from bcm2708-i2s driver in Raspberry Pi tree.
RPi commit c14827ecda ("bcm2708: Allow
option card devices to be configured via DT")
Original work by Zoltan Szenczi, committed to RPi tree by
Phil Elwell.
Signed-off-by: Matthias Reichl <hias@horus.com>
Code ported from bcm2708-i2s driver in Raspberry Pi tree.
RPi commit 62c05a0b53 ("ASoC: BCM2708:
Add 24 bit support")
This adds 24 bit support to the I2S driver of the BCM2708.
Besides enabling the 24 bit flags, it includes two bug fixes:
MMAP is not supported. Claiming this leads to strange issues
when the format of driver and file do not match.
The datasheet states that the width extension bit should be set
for widths greater than 24, but greater or equal would be correct.
This follows from the definition of the width field.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
RPi commit 3e8c672bc4 ("bcm2708-i2s:
Update bclk_ratio to more correct values")
Discussion about blck_ratio affecting sound quality:
https://github.com/raspberrypi/linux/issues/681
Signed-off-by: Matthias Reichl <hias@horus.com>
The VideoCore bootloader passes in Serial number and
Revision number through Device Tree. Make these available to
userspace through /proc/cpuinfo.
Mainline status:
There is a commit in linux-next that standardize passing the serial
number through Device Tree (string: /serial-number):
ARM: 8355/1: arch: Show the serial number from devicetree in cpuinfo
There was an attempt to do the same with the revision number, but it
didn't get in:
[PATCH v2 1/2] arm: devtree: Set system_rev from DT revision
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
The spi-bcm2835 driver automatically uses GPIO chip-selects due to
some unreliability of the native ones. In doing so it chooses the
same pins as the native chip-selects would use, but the existing
code always uses pins 7 and 8, wherever the SPI function is mapped.
Search the pinctrl group assigned to the driver for pins that
correspond to native chip-selects, and use those for GPIO chip-
selects.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Although the GPIO controller can generate three interrupts (four counting
the common one), the device tree files currently only specify two. In the
absence of the third, simply don't register that interrupt (as opposed to
registering 0), which has the effect of making it impossible to generate
interrupts for GPIOs 46-53 which, since they share pins with the SD card
interface, is unlikely to be a problem.
Contrary to the documentation, the BCM2835 GPIO controller actually has
four interrupt lines - one each for the three IRQ groups and one common. Rather
confusingly, the GPIO interrupt groups don't correspond directly with the GPIO
control banks. Instead, GPIOs 0-27 generate IRQ GPIO0, 28-45 GPIO1 and
46-53 GPIO2.
Awkwardly, the GPIOS for IRQ GPIO1 straddle two 32-entry GPIO banks, so it is
cleaner to split out a function to process the interrupts for a single GPIO
bank.
This bug has only just been observed because GPIOs above 27 can only be
accessed on an old Raspberry Pi with the optional P5 header fitted, where
the pins are often used for I2S instead.
Add a duplicate irq range with an offset on the hwirq's so the
driver can detect that enable_fiq() is used.
Tested with downstream dwc_otg USB controller driver.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
The old arch-specific IRQ macros included a dsb to ensure the
write to clear the mailbox interrupt completed before returning
from the interrupt. The BCM2836 irqchip driver needs the same
precaution to avoid spurious interrupts.
Spurious interrupts are still possible for other reasons,
though, so trap them early.
See commit dae803e165 -- the warning is
expected sometimes when using CMA. However, that commit still spams
my kernel log with these warnings.
Signed-off-by: Eric Anholt <eric@anholt.net>
tty_port_hangup sets a port's tty field to NULL (holding the port lock),
but uart_tx_stopped, called from __uart_start (with the port lock),
uses the tty field without checking for NULL.
Change uart_tx_stopped to treat a NULL tty field as another stopped
indication.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
smsc95xx is adjusting truesize when it shouldn't, and following a recent patch from Eric this is now triggering warnings.
This patch stops smsc95xx from changing truesize.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
commit 059f791c6b upstream.
Similar to __clear_extent_bit, do not fail if the state preallocation
fails as we might not need it. One less BUG_ON.
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f1fee6534d upstream.
We usually call btrfs_put_bbio() when btrfs_map_block() failed,
btrfs_put_bbio() works right whether bbio is a valid value, or NULL.
But there is a exception, in some case, btrfs_map_block() will return
fail without touching *bbio(keeping its original value), and if bbio
was not initialized yet, invalid memory accessing will happened.
Above case is in scrub_missing_raid56_pages(), and similar case in
scrub_raid56_parity().
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2d324f59f3 upstream.
btrfs's fiemap is supposed to return 0 on success and return < 0 on
error. however, ret becomes 1 after looking up the last file extent:
btrfs_lookup_file_extent ->
btrfs_search_slot(..., ins_len=0, cow=0)
and if the offset is beyond EOF, we'll get 'path' pointed to the place
of potentail insertion, and ret == 1.
This may confuse applications using ioctl(FIEL_IOC_FIEMAP).
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f9749f6e9 upstream.
If we create a symlink, fsync its parent directory, crash/power fail and
mount the filesystem, we end up with an empty symlink, which not only is
useless it's also not allowed in linux (the man page symlink(2) is well
explicit about that). So we just need to make sure to fully log an inode
if it's a symlink, to ensure its inline extent gets logged, ensuring the
same behaviour as ext3, ext4, xfs, reiserfs, f2fs, nilfs2, etc.
Example reproducer:
$ mkfs.btrfs -f /dev/sdb
$ mount /dev/sdb /mnt
$ mkdir /mnt/testdir
$ sync
$ ln -s /mnt/foo /mnt/testdir/bar
$ xfs_io -c fsync /mnt/testdir
<power fail>
$ mount /dev/sdb /mnt
$ readlink /mnt/testdir/bar
<empty string>
A test case for fstests follows soon.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 657ed1aa48 upstream.
If we move a directory to a new parent and later log that parent and don't
explicitly log the old parent, when we replay the log we can end up with
entries for the moved directory in both the old and new parent directories.
Besides being ilegal to have directories with multiple hard links in linux,
it also resulted in the leaving the inode item with a link count of 1.
A similar issue also happens if we move a regular file - after the log tree
is replayed the file has a link in both the old and new parent directories,
when it should be only at the new directory.
Sample reproducer:
$ mkfs.btrfs -f /dev/sdc
$ mount /dev/sdc /mnt
$ mkdir /mnt/x
$ mkdir /mnt/y
$ touch /mnt/x/foo
$ mkdir /mnt/y/z
$ sync
$ ln /mnt/x/foo /mnt/x/bar
$ mv /mnt/y/z /mnt/x/z
< power fail >
$ mount /dev/sdc /mnt
$ ls -1Ri /mnt
/mnt:
257 x
258 y
/mnt/x:
259 bar
259 foo
260 z
/mnt/x/z:
/mnt/y:
260 z
/mnt/y/z:
$ umount /dev/sdc
$ btrfs check /dev/sdc
Checking filesystem on /dev/sdc
UUID: a67e2c4a-a4b4-4fdc-b015-9d9af1e344be
checking extents
checking free space cache
checking fs roots
root 5 inode 260 errors 2000, link count wrong
unresolved ref dir 257 index 4 namelen 1 name z filetype 2 errors 0
unresolved ref dir 258 index 2 namelen 1 name z filetype 2 errors 0
(...)
Attempting to remove the directory becomes impossible:
$ mount /dev/sdc /mnt
$ rmdir /mnt/y/z
$ ls -lh /mnt/y
ls: cannot access /mnt/y/z: No such file or directory
total 0
d????????? ? ? ? ? ? z
$ rmdir /mnt/x/z
rmdir: failed to remove ‘/mnt/x/z’: Stale file handle
$ ls -lh /mnt/x
ls: cannot access /mnt/x/z: Stale file handle
total 0
-rw-r--r-- 2 root root 0 Apr 6 18:06 bar
-rw-r--r-- 2 root root 0 Apr 6 18:06 foo
d????????? ? ? ? ? ? z
So make sure that on rename we set the last_unlink_trans value for our
inode, even if it's a directory, to the value of the current transaction's
ID and that if the new parent directory is logged that we fallback to a
transaction commit.
A test case for fstests is being submitted as well.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 72928f2476 upstream.
Make sure to deallocate fspath with vfree() in case of error in
init_ipath().
fspath is allocated with vmalloc() in init_data_container() since
commit 425d17a290 ("Btrfs: use larger limit for translation of logical to
inode").
Signed-off-by: Vincent Stehlé <vincent.stehle@intel.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8eb0dfdbda upstream.
UBSAN: Undefined behaviour in fs/btrfs/extent-tree.c:4623:21
signed integer overflow:
10808 * 262144 cannot be represented in type 'int [8]'
If 8192<=items<16384, we request a writeback of an insane number of pages
which is benign (everything will be written). But if items>=16384, the
space reservation won't be enough.
Signed-off-by: Adam Borowski <kilobyte@angband.pl>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 48b3b9d401 upstream.
Move scratch super outside of the chunk lock to avoid below
lockdep warning. The better place to scratch super is in
the function btrfs_rm_dev_replace_free_srcdev() just before
free_device, which is outside of the chunk lock as well.
To reproduce:
(fresh boot)
mkfs.btrfs -f -draid5 -mraid5 /dev/sdc /dev/sdd /dev/sde
mount /dev/sdc /btrfs
dd if=/dev/zero of=/btrfs/tf1 bs=4096 count=100
(get devmgt from https://github.com/asj/devmgt.git)
devmgt detach /dev/sde
dd if=/dev/zero of=/btrfs/tf1 bs=4096 count=100
sync
btrfs replace start -Brf 3 /dev/sdf /btrfs <--
devmgt attach host7
======================================================
[ INFO: possible circular locking dependency detected ]
4.6.0-rc2asj+ #1 Not tainted
---------------------------------------------------
btrfs/2174 is trying to acquire lock:
(sb_writers){.+.+.+}, at:
[<ffffffff812449b4>] __sb_start_write+0xb4/0xf0
but task is already holding lock:
(&fs_info->chunk_mutex){+.+.+.}, at:
[<ffffffffa05c5f55>] btrfs_dev_replace_finishing+0x145/0x980 [btrfs]
which lock already depends on the new lock.
Chain exists of:
sb_writers --> &fs_devs->device_list_mutex --> &fs_info->chunk_mutex
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&fs_info->chunk_mutex);
lock(&fs_devs->device_list_mutex);
lock(&fs_info->chunk_mutex);
lock(sb_writers);
commit e042d1ec44 upstream.
btrfs_map_block can go horribly wrong in the face of fs corruption, lets agree
to not be assholes and panic at any possible chance things are all fucked up.
Signed-off-by: Josef Bacik <jbacik@fb.com>
[ removed type casts ]
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d8da67817 upstream.
The struct 'map_lookup' uses type int for @stripe_len, while
btrfs_chunk_stripe_len() can return a u64 value, and it may end up with
@stripe_len being undefined value and it can lead to 'divide error' in
__btrfs_map_block().
This changes 'map_lookup' to use type u64 for stripe_len, also right now
we only use BTRFS_STRIPE_LEN for stripe_len, so this adds a valid checker for
BTRFS_STRIPE_LEN.
Reported-by: Vegard Nossum <vegard.nossum@oracle.com>
Reported-by: Quentin Casasnovas <quentin.casasnovas@oracle.com>
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ folded division fix to scrub_raid56_parity ]
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66ac9fe7ba upstream.
Add a sanity check for the fs_info as we will dereference it, similar to
what the 'store features' handler does.
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee6111386a upstream.
We don't want to trigger the change on a read-only filesystem, similar
to what the label handler does.
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 41b34accb2 upstream.
Since mixed block groups accounting isn't byte-accurate and f_bree is an
unsigned integer, it could overflow. Avoid this.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Suggested-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 88be159c90 upstream.
Currently, we don't allow the user to try and rebalance to a dup profile
on a multi-device filesystem. In most cases, this is a perfectly sensible
restriction as raid1 uses the same amount of space and provides better
protection.
However, when reshaping a multi-device filesystem down to a single device
filesystem, this requires the user to convert metadata and system chunks
to single profile before deleting devices, and then convert again to dup,
which leaves a period of time where metadata integrity is reduced.
This patch removes the single-device-only restriction from converting to
dup profile to remove this potential data integrity reduction.
Signed-off-by: Austin S. Hemmelgarn <ahferroin7@gmail.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cf25ce518e upstream.
Now we force to create empty block group to keep data profile alive,
however, in the below example, we eventually get an empty block group
while we're trying to get more space for other types (metadata/system),
- Before,
block group "A": size=2G, used=1.2G
block group "B": size=2G, used=512M
- After "btrfs balance start -dusage=50 mount_point",
block group "A": size=2G, used=(1.2+0.5)G
block group "C": size=2G, used=0
Since there is no data in block group C, it won't be deleted
automatically and we have to get the unused 2G until the next mount.
Balance itself just moves data and doesn't remove data, so it's safe
to not create such a empty block group if we already have data
allocated in other block groups.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c63c2454e upstream.
32-bit ioctl uses these rather than the regular FS_IOC_* versions. They can
be handled in btrfs using the same code. Without this, 32-bit {ch,ls}attr
fail.
Signed-off-by: Luke Dashjr <luke-jr+git@utopios.org>
Reviewed-by: Josef Bacik <jbacik@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 51b07f30a7 upstream.
Some careless idiot(*) wrote crap code in commit 1a3e8f3 ("xfs:
convert inode cache lookups to use RCU locking") back in late 2010,
and so xfs_iflush_cluster checks the wrong inode for whether it is
still valid under RCU protection. Fix it to lock and check the
correct inode.
(*) Careless-idiot: Dave Chinner <dchinner@redhat.com>
Discovered-by: Brain Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b1438f4779 upstream.
When a failure due to an inode buffer occurs, the error handling
fails to abort the inode writeback correctly. This can result in the
inode being reclaimed whilst still in the AIL, leading to
use-after-free situations as well as filesystems that cannot be
unmounted as the inode log items left in the AIL never get removed.
Fix this by ensuring fatal errors from xfs_imap_to_bp() result in
the inode flush being aborted correctly.
Reported-by: Shyam Kaushik <shyam@zadarastorage.com>
Diagnosed-by: Shyam Kaushik <shyam@zadarastorage.com>
Tested-by: Shyam Kaushik <shyam@zadarastorage.com>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ad747e3b29 upstream.
Commit 96f859d ("libxfs: pack the agfl header structure so
XFS_AGFL_SIZE is correct") allowed the freelist to use the empty
slot at the end of the freelist on 64 bit systems that was not
being used due to sizeof() rounding up the structure size.
This has caused versions of xfs_repair prior to 4.5.0 (which also
has the fix) to report this as a corruption once the filesystem has
been grown. Older kernels can also have problems (seen from a whacky
container/vm management environment) mounting filesystems grown on a
system with a newer kernel than the vm/container it is deployed on.
To avoid this problem, change the initial free list indexes not to
wrap across the end of the AGFL, hence avoiding the initialisation
of agf_fllast to the last index in the AGFL.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0a58e8339 upstream.
Today, a kernel which refuses to mount a filesystem read-write
due to unknown ro-compat features can still transition to read-write
via the remount path. The old kernel is most likely none the wiser,
because it's unaware of the new feature, and isn't using it. However,
writing to the filesystem may well corrupt metadata related to that
new feature, and moving to a newer kernel which understand the feature
will have problems.
Right now the only ro-compat feature we have is the free inode btree,
which showed up in v3.16. It would be good to push this back to
all the active stable kernels, I think, so that if anyone is using
newer mkfs (which enables the finobt feature) with older kernel
releases, they'll be protected.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Bill O'Donnell <billodo@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c87bf43144 upstream.
Enabling CONFIG_GCOV_PROFILE_ALL produces us a lot of warnings like
lib/lz4/lz4hc_compress.c: In function 'lz4_compresshcctx':
lib/lz4/lz4hc_compress.c:514:1: warning: the frame size of 1504 bytes is larger than 1024 bytes [-Wframe-larger-than=]
After some investigation, I found that this behavior started with gcc-4.9,
and opened https://gcc.gnu.org/bugzilla/show_bug.cgi?id=69702.
A suggested workaround for it is to use the -fno-tree-loop-im
flag that turns off one of the optimization stages in gcc, so the
code runs a little slower but does not use excessive amounts
of stack.
We could make this conditional on the gcc version, but I could not
find an easy way to do this in Kbuild and the benefit would be
fairly small, given that most of the gcc version in production are
affected now.
I'm marking this for 'stable' backports because it addresses a bug
with code generation in gcc that exists in all kernel versions
with the affected gcc releases.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Michal Marek <mmarek@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 65a9f31c50 upstream.
After commit 21a59991ce ("scripts/package/Makefile: rpmbuild is needed
for rpm targets"), it is no longer possible to specify RPMOPTS.
For example, we can no longer able to control _topdir using the following
make command.
make RPMOPTS="--define '_topdir /home/xyz/workspace/'" binrpm-pkg
Fixes: 21a59991ce ("scripts/package/Makefile: rpmbuild is needed for rpm targets")
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Michal Marek <mmarek@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a17fb329d upstream.
Grygorii Strashko reports:
The PM runtime will be left disabled for the device if its
.suspend_late() callback fails and async suspend is not allowed
for this device. In this case device will not be added in
dpm_late_early_list and dpm_resume_early() will ignore this
device, as result PM runtime will be disabled for it forever
(side effect: after 8 subsequent failures for the same device
the PM runtime will be reenabled due to disable_depth overflow).
To fix this problem, add devices to dpm_late_early_list regardless
of whether or not device_suspend_late() returns errors for them.
That will ensure failures in there to be handled consistently for
all devices regardless of their async suspend/resume status.
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 935244cd54 upstream.
Currently, in ext4_mb_init(), there's a loop like the following:
do {
...
offset += 1 << (sb->s_blocksize_bits - i);
i++;
} while (i <= sb->s_blocksize_bits + 1);
Note that the updated offset is used in the loop's next iteration only.
However, at the last iteration, that is at i == sb->s_blocksize_bits + 1,
the shift count becomes equal to (unsigned)-1 > 31 (c.f. C99 6.5.7(3))
and UBSAN reports
UBSAN: Undefined behaviour in fs/ext4/mballoc.c:2621:15
shift exponent 4294967295 is too large for 32-bit type 'int'
[...]
Call Trace:
[<ffffffff818c4d25>] dump_stack+0xbc/0x117
[<ffffffff818c4c69>] ? _atomic_dec_and_lock+0x169/0x169
[<ffffffff819411ab>] ubsan_epilogue+0xd/0x4e
[<ffffffff81941cac>] __ubsan_handle_shift_out_of_bounds+0x1fb/0x254
[<ffffffff81941ab1>] ? __ubsan_handle_load_invalid_value+0x158/0x158
[<ffffffff814b6dc1>] ? kmem_cache_alloc+0x101/0x390
[<ffffffff816fc13b>] ? ext4_mb_init+0x13b/0xfd0
[<ffffffff814293c7>] ? create_cache+0x57/0x1f0
[<ffffffff8142948a>] ? create_cache+0x11a/0x1f0
[<ffffffff821c2168>] ? mutex_lock+0x38/0x60
[<ffffffff821c23ab>] ? mutex_unlock+0x1b/0x50
[<ffffffff814c26ab>] ? put_online_mems+0x5b/0xc0
[<ffffffff81429677>] ? kmem_cache_create+0x117/0x2c0
[<ffffffff816fcc49>] ext4_mb_init+0xc49/0xfd0
[...]
Observe that the mentioned shift exponent, 4294967295, equals (unsigned)-1.
Unless compilers start to do some fancy transformations (which at least
GCC 6.0.0 doesn't currently do), the issue is of cosmetic nature only: the
such calculated value of offset is never used again.
Silence UBSAN by introducing another variable, offset_incr, holding the
next increment to apply to offset and adjust that one by right shifting it
by one position per loop iteration.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=114701
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=112161
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5cb316cdf upstream.
Currently, in mb_find_order_for_block(), there's a loop like the following:
while (order <= e4b->bd_blkbits + 1) {
...
bb += 1 << (e4b->bd_blkbits - order);
}
Note that the updated bb is used in the loop's next iteration only.
However, at the last iteration, that is at order == e4b->bd_blkbits + 1,
the shift count becomes negative (c.f. C99 6.5.7(3)) and UBSAN reports
UBSAN: Undefined behaviour in fs/ext4/mballoc.c:1281:11
shift exponent -1 is negative
[...]
Call Trace:
[<ffffffff818c4d35>] dump_stack+0xbc/0x117
[<ffffffff818c4c79>] ? _atomic_dec_and_lock+0x169/0x169
[<ffffffff819411bb>] ubsan_epilogue+0xd/0x4e
[<ffffffff81941cbc>] __ubsan_handle_shift_out_of_bounds+0x1fb/0x254
[<ffffffff81941ac1>] ? __ubsan_handle_load_invalid_value+0x158/0x158
[<ffffffff816e93a0>] ? ext4_mb_generate_from_pa+0x590/0x590
[<ffffffff816502c8>] ? ext4_read_block_bitmap_nowait+0x598/0xe80
[<ffffffff816e7b7e>] mb_find_order_for_block+0x1ce/0x240
[...]
Unless compilers start to do some fancy transformations (which at least
GCC 6.0.0 doesn't currently do), the issue is of cosmetic nature only: the
such calculated value of bb is never used again.
Silence UBSAN by introducing another variable, bb_incr, holding the next
increment to apply to bb and adjust that one by right shifting it by one
position per loop iteration.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=114701
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=112161
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff0bc08454 upstream.
A failed call to dqget() returns an ERR_PTR() and not null. Fix
the check in ext4_ioctl_setproject() to handle this correctly.
Fixes: 9b7365fc1c ("ext4: add FS_IOC_FSSETXATTR/FS_IOC_FSGETXATTR interface support")
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7827a7f6eb upstream.
Instead of just printing warning messages, if the orphan list is
corrupted, declare the file system is corrupted. If there are any
reserved inodes in the orphaned inode list, declare the file system
corrupted and stop right away to avoid doing more potential damage to
the file system.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c9eb13a910 upstream.
If the orphaned inode list contains inode #5, ext4_iget() returns a
bad inode (since the bootloader inode should never be referenced
directly). Because of the bad inode, we end up processing the inode
repeatedly and this hangs the machine.
This can be reproduced via:
mke2fs -t ext4 /tmp/foo.img 100
debugfs -w -R "ssv last_orphan 5" /tmp/foo.img
mount -o loop /tmp/foo.img /mnt
(But don't do this if you are using an unpatched kernel if you care
about the system staying functional. :-)
This bug was found by the port of American Fuzzy Lop into the kernel
to find file system problems[1]. (Since it *only* happens if inode #5
shows up on the orphan list --- 3, 7, 8, etc. won't do it, it's not
surprising that AFL needed two hours before it found it.)
[1] http://events.linuxfoundation.org/sites/events/files/slides/AFL%20filesystem%20fuzzing%2C%20Vault%202016_0.pdf
Reported by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 310944d148 upstream.
The component master driver imx-drm-core matches component devices using
their of_node. Since commit 950b410dd1ab ("gpu: ipu-v3: Fix imx-ipuv3-crtc
module autoloading"), the imx-ipuv3-crtc dev->of_node is not set during
probing. Before that, of_node was set and caused an of: modalias to be
used instead of the platform: modalias, which broke module autoloading.
On the other hand, if dev->of_node is not set yet when the imx-ipuv3-crtc
probe function calls component_add, component matching in imx-drm-core
fails. While dev->of_node will be set once the next component tries to
bring up the component master, imx-drm-core component binding will never
succeed if one of the crtc devices is probed last.
Add of_node to the component platform data and match against the
pdata->of_node instead of dev->of_node in imx-drm-core to work around
this problem.
Fixes: 950b410dd1ab ("gpu: ipu-v3: Fix imx-ipuv3-crtc module autoloading")
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Lothar Waßmann <LW@KARO-electronics.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 55441070ca upstream.
The memcpy of ipv6 header destination address to the skb control block
(sbk->cb) in header_create() results in currupted memory when bt_xmit()
is issued. The skb->cb is "released" in the return of header_create()
making room for lower layer to minipulate the skb->cb.
The value retrieved in bt_xmit is not persistent across header creation
and sending, and the lower layer will overwrite portions of skb->cb,
making the copied destination address wrong.
The memory corruption will lead to non-working multicast as the first 4
bytes of the copied destination address is replaced by a value that
resolves into a non-multicast prefix.
This fix removes the dependency on the skb control block between header
creation and send, by moving the destination address memcpy to the send
function path (setup_create, which is called from bt_xmit).
Signed-off-by: Glenn Ruben Bakke <glenn.ruben.bakke@nordicsemi.no>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unfortunately since we don't have Dave's connector refcounting patch
here yet, it's very possible that drm_atomic_state_default_clear() could
get called by intel_display_resume() when
intel_dp_mst_destroy_connector() isn't completely finished destroying an
mst connector, but has already finished setting connector->funcs to
NULL. As such, we need to treat the connector like it's already been
destroyed and just skip it, otherwise we'll end up dereferencing a NULL
pointer.
This fix is only required for 4.6 and below. David Airlie's patchseries
for 4.7 to add connector reference counting provides a more proper fix
for this.
Changes since v1:
- Fix leftover whitespace
Upstream fix: 0552f7651b ("drm/i915/mst: use reference counted
connectors. (v3)")
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Lyude <cpaul@redhat.com>
commit 255f0e7c41 upstream.
During boot, MST hotplugs are generally expected (even if no physical
hotplugging occurs) and result in DRM's connector topology changing.
This means that using num_connector from the current mode configuration
can lead to the number of connectors changing under us. This can lead to
some nasty scenarios in fbcon:
- We allocate an array to the size of dev->mode_config.num_connectors.
- MST hotplug occurs, dev->mode_config.num_connectors gets incremented.
- We try to loop through each element in the array using the new value
of dev->mode_config.num_connectors, and end up going out of bounds
since dev->mode_config.num_connectors is now larger then the array we
allocated.
fb_helper->connector_count however, will always remain consistent while
we do a modeset in fb_helper.
Note: This is just polish for 4.7, Dave Airlie's drm_connector
refcounting fixed these bugs for real. But it's good enough duct-tape
for stable kernel backporting, since backporting the refcounting
changes is way too invasive.
Signed-off-by: Lyude <cpaul@redhat.com>
[danvet: Clarify why we need this. Also remove the now unused "dev"
local variable to appease gcc.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1463065021-18280-3-git-send-email-cpaul@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 14a3842a1d upstream.
During boot time, MST devices usually send a ton of hotplug events
irregardless of whether or not any physical hotplugs actually occurred.
Hotplugs mean connectors being created/destroyed, and the number of DRM
connectors changing under us. This isn't a problem if we use
fb_helper->connector_count since we only set it once in the code,
however if we use num_connector from struct drm_mode_config we risk it's
value changing under us. On top of that, there's even a chance that
dev->mode_config.num_connector != fb_helper->connector_count. If the
number of connectors happens to increase under us, we'll end up using
the wrong array size for memcpy and start writing beyond the actual
length of the array, occasionally resulting in kernel panics.
Note: This is just polish for 4.7, Dave Airlie's drm_connector
refcounting fixed these bugs for real. But it's good enough duct-tape
for stable kernel backporting, since backporting the refcounting
changes is way too invasive.
Signed-off-by: Lyude <cpaul@redhat.com>
[danvet: Clarify why we need this.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1463065021-18280-2-git-send-email-cpaul@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9d746ab681 upstream.
When porting the hdmi deep color detection code from
radeon-kms to amdgpu-kms apparently some kind of
copy and paste error happened, attaching an else
branch to the wrong if statement.
The result is that hdmi deep color mode is always
disabled, regardless of gpu and display capabilities and
user wishes, as the code mistakenly thinks that the display
doesn't provide the required max_tmds_clock limit and falls
back to 8 bpc.
This patch fixes deep color support, as tested on a
R9 380 Tonga Pro + suitable display, and should be
backported to all kernels with amdgpu-kms support.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7851496a32 upstream.
mode->hdisplay * (var->bits_per_pixel + 7) gets evaluated before
the division, potentially making the pitch larger than it should
be.
Since the original intention is to do a div-round-up, just use
the macro instead.
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e02e588431 upstream.
Instead of calling vmw_cmd_ok, call vmw_cmd_dx_cid_check to
validate the context id for query commands.
Signed-off-by: Charmaine Lee <charmainel@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ccca1d5bf upstream.
Fix possible out of bounds read, by adding missing comma.
The code may read pass the end of the dsi_errors array
when the most significant bit (bit #31) in the intr_stat register
is set.
This bug has been detected using CppCheck (static analysis tool).
Signed-off-by: Itai Handler <itai_handler@hotmail.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c0cb8bf3a8 upstream.
The length of the GSS MIC token need not be a multiple of four bytes.
It is then padded by XDR to a multiple of 4 B, but unwrap_integ_data()
would previously only trim mic.len + 4 B. The remaining up to three
bytes would then trigger a check in nfs4svc_decode_compoundargs(),
leading to a "garbage args" error and mount failure:
nfs4svc_decode_compoundargs: compound not properly padded!
nfsd: failed to decode arguments!
This would prevent older clients using the pre-RFC 4121 MIC format
(37-byte MIC including a 9-byte OID) from mounting exports from v3.9+
servers using krb5i.
The trimming was introduced by commit 4c190e2f91 ("sunrpc: trim off
trailing checksum before returning decrypted or integrity authenticated
buffer").
Fixes: 4c190e2f91 "unrpc: trim off trailing checksum..."
Signed-off-by: Tomáš Trnka <ttrnka@mail.muni.cz>
Acked-by: Jeff Layton <jlayton@poochiereds.net>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd14be92fb upstream.
Instead of having two functions for cycling through the E820 map in
order to count to be remapped pages and remap them later, just use one
function with a caller supplied sub-function called for each region to
be processed. This eliminates the possibility of a mismatch between
both loops which showed up in certain configurations.
Suggested-by: Ed Swierk <eswierk@skyportsystems.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5a0cdbfd17 upstream.
The function eeh_pe_reset_and_recover() is used to recover EEH
error when the passthrou device are transferred to guest and
backwards. The content in the device's config space will be lost
on PE reset issued in the middle of the recovery. The function
saves/restores it before/after the reset. However, config access
to some adapters like Broadcom BCM5719 at this point will causes
fenced PHB. The config space is always blocked and we save 0xFF's
that are restored at late point. The memory BARs are totally
corrupted, causing another EEH error upon access to one of the
memory BARs.
This restores the config space on those adapters like BCM5719
from the content saved to the EEH device when it's populated,
to resolve above issue.
Fixes: 5cfb20b9 ("powerpc/eeh: Emulate EEH recovery for VFIO devices")
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2078d9ef6 upstream.
This reverts commit 89a51df5ab.
The function eeh_add_device_early() is used to perform EEH
initialization in devices added later on the system, like in
hotplug/DLPAR scenarios. Since the commit 89a51df5ab ("powerpc/eeh:
Fix crash in eeh_add_device_early() on Cell") a new check was introduced
in this function - Cell has no EEH capabilities which led to kernel oops
if hotplug was performed, so checking for eeh_enabled() was introduced
to avoid the issue.
However, in architectures that EEH is present like pSeries or PowerNV,
we might reach a case in which no PCI devices are present on boot time
and so EEH is not initialized. Then, if a device is added via DLPAR for
example, eeh_add_device_early() fails because eeh_enabled() is false,
and EEH end up not being enabled at all.
This reverts the aforementioned patch since a new verification was
introduced by the commit d91dafc02f ("powerpc/eeh: Delay probing EEH
device during hotplug") and so the original Cell issue does not happen
anymore.
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit affeb0f2d3 upstream.
The function eeh_pe_reset_and_recover() is used to recover EEH
error when the passthrough device are transferred to guest and
backwards, meaning the device's driver is vfio-pci or none.
When the driver is vfio-pci that provides error_detected() error
handler only, the handler simply stops the guest and it's not
expected behaviour. On the other hand, no error handlers will
be called if we don't have a bound driver.
This ignores the error handler in eeh_pe_reset_and_recover()
that reports the error to device driver to avoid the exceptional
behaviour.
Fixes: 5cfb20b9 ("powerpc/eeh: Emulate EEH recovery for VFIO devices")
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ed8ab4004 upstream.
Some of the interrupt vectors on 64-bit POWER server processors are only
32 bytes long (8 instructions), which is not enough for the full
first-level interrupt handler. For these we need to branch to an
out-of-line (OOL) handler. But when we are running a relocatable kernel,
interrupt vectors till __end_interrupts marker are copied down to real
address 0x100. So, branching to labels (ie. OOL handlers) outside this
section must be handled differently (see LOAD_HANDLER()), considering
relocatable kernel, which would need at least 4 instructions.
However, branching from interrupt vector means that we corrupt the
CFAR (come-from address register) on POWER7 and later processors as
mentioned in commit 1707dd16. So, EXCEPTION_PROLOG_0 (6 instructions)
that contains the part up to the point where the CFAR is saved in the
PACA should be part of the short interrupt vectors before we branch out
to OOL handlers.
But as mentioned already, there are interrupt vectors on 64-bit POWER
server processors that are only 32 bytes long (like vectors 0x4f00,
0x4f20, etc.), which cannot accomodate the above two cases at the same
time owing to space constraint. Currently, in these interrupt vectors,
we simply branch out to OOL handlers, without using LOAD_HANDLER(),
which leaves us vulnerable when running a relocatable kernel (eg. kdump
case). While this has been the case for sometime now and kdump is used
widely, we were fortunate not to see any problems so far, for three
reasons:
1. In almost all cases, production kernel (relocatable) is used for
kdump as well, which would mean that crashed kernel's OOL handler
would be at the same place where we end up branching to, from short
interrupt vector of kdump kernel.
2. Also, OOL handler was unlikely the reason for crash in almost all
the kdump scenarios, which meant we had a sane OOL handler from
crashed kernel that we branched to.
3. On most 64-bit POWER server processors, page size is large enough
that marking interrupt vector code as executable (see commit
429d2e83) leads to marking OOL handler code from crashed kernel,
that sits right below interrupt vector code from kdump kernel, as
executable as well.
Let us fix this by moving the __end_interrupts marker down past OOL
handlers to make sure that we also copy OOL handlers to real address
0x100 when running a relocatable kernel.
This fix has been tested successfully in kdump scenario, on an LPAR with
4K page size by using different default/production kernel and kdump
kernel.
Also tested by manually corrupting the OOL handlers in the first kernel
and then kdump'ing, and then causing the OOL handlers to fire - mpe.
Fixes: c1fb6816fb ("powerpc: Add relocation on exception vector handlers")
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 11ca2b7ab4 upstream.
New bindings use "fsl,t1040-ucc-uart" as the compatible for qe-uart.
So add it.
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf959931dd upstream.
The following program (simplified version of generated by syzkaller)
#include <pthread.h>
#include <unistd.h>
#include <sys/ptrace.h>
#include <stdio.h>
#include <signal.h>
void *thread_func(void *arg)
{
ptrace(PTRACE_TRACEME, 0,0,0);
return 0;
}
int main(void)
{
pthread_t thread;
if (fork())
return 0;
while (getppid() != 1)
;
pthread_create(&thread, NULL, thread_func, NULL);
pthread_join(thread, NULL);
return 0;
}
creates an unreapable zombie if /sbin/init doesn't use __WALL.
This is not a kernel bug, at least in a sense that everything works as
expected: debugger should reap a traced sub-thread before it can reap the
leader, but without __WALL/__WCLONE do_wait() ignores sub-threads.
Unfortunately, it seems that /sbin/init in most (all?) distributions
doesn't use it and we have to change the kernel to avoid the problem.
Note also that most init's use sys_waitid() which doesn't allow __WALL, so
the necessary user-space fix is not that trivial.
This patch just adds the "ptrace" check into eligible_child(). To some
degree this matches the "tsk->ptrace" in exit_notify(), ->exit_signal is
mostly ignored when the tracee reports to debugger. Or WSTOPPED, the
tracer doesn't need to set this flag to wait for the stopped tracee.
This obviously means the user-visible change: __WCLONE and __WALL no
longer have any meaning for debugger. And I can only hope that this won't
break something, but at least strace/gdb won't suffer.
We could make a more conservative change. Say, we can take __WCLONE into
account, or !thread_group_leader(). But it would be nice to not
complicate these historical/confusing checks.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Jan Kratochvil <jan.kratochvil@redhat.com>
Cc: "Michael Kerrisk (man-pages)" <mtk.manpages@gmail.com>
Cc: Pedro Alves <palves@redhat.com>
Cc: Roland McGrath <roland@hack.frob.com>
Cc: <syzkaller@googlegroups.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4b50bcc7ed upstream.
Since commit 92923ca3aa ("mm: meminit: only set page reserved in the
memblock region") the reserved bit is set on reserved memblock regions.
However start and end address are passed as unsigned long. This is only
32bit on i386, so it can end up marking the wrong pages reserved for
ranges at 4GB and above.
This was observed on a 32bit Xen dom0 which was booted with initial
memory set to a value below 4G but allowing to balloon in memory
(dom0_mem=1024M for example). This would define a reserved bootmem
region for the additional memory (for example on a 8GB system there was
a reverved region covering the 4GB-8GB range). But since the addresses
were passed on as unsigned long, this was actually marking all pages
from 0 to 4GB as reserved.
Fixes: 92923ca3aa ("mm: meminit: only set page reserved in the memblock region")
Link: http://lkml.kernel.org/r/1463491221-10573-1-git-send-email-stefan.bader@canonical.com
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit baf43c6eac upstream.
In v4l2-compliance utility, test VIDIOC_CREATE_BUFS will check whether reserved
filed of v4l2_create_buffers filled with zero
Reserved field is filled with zero in v4l_create_bufs.
This patch copy reserved field of v4l2_create_buffer from kernel space to user
space
Signed-off-by: Tiffany Lin <tiffany.lin@mediatek.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ad67b437f1 upstream.
b84106b4e2 ("PCI: Disable IO/MEM decoding for devices with non-compliant
BARs") disabled BAR sizing for BARs 0-5 of devices that don't comply with
the PCI spec. But it didn't do anything for expansion ROM BARs, so we
still try to size them, resulting in warnings like this on Broadwell-EP:
pci 0000:ff:12.0: BAR 6: failed to assign [mem size 0x00000001 pref]
Move the non-compliant BAR check from __pci_read_base() up to
pci_read_bases() so it applies to the expansion ROM BAR as well as
to BARs 0-5.
Note that direct callers of __pci_read_base(), like sriov_init(), will now
bypass this check. We haven't had reports of devices with broken SR-IOV
BARs yet.
[bhelgaas: changelog]
Fixes: b84106b4e2 ("PCI: Disable IO/MEM decoding for devices with non-compliant BARs")
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Ingo Molnar <mingo@redhat.com>
CC: "H. Peter Anvin" <hpa@zytor.com>
CC: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 71324fdc72 upstream.
The range is registered into a linked list which can be referenced
throughout the lifetime of the driver. Ensure the range's memory is useful
for the same lifetime by adding it to the driver's private data structure.
The bug was introduced in the driver's initial commit, which was present in
v3.10.
Fixes: f0b9a7e521 ("pinctrl: exynos5440: add pinctrl driver for Samsung EXYNOS5440 SoC")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 959ca92a32 upstream.
The current driver calculates the clock divider with
fractional support enabled.
But it does not enable fractional support in the
control register itself resulting in an integer only divider,
but in clk_set_rate responds back the fractionally divided
clock frequency.
This patch enables fractional support in the control register
whenever there is a fractional bit set in the requested clock divider.
Mash clock limits are are also handled for the PWM clock
applying the correct divider limits (2 and max_int) applicable to
basic fractional divider support (mash order of 1).
It also adds locking to protect the read/modify/write cycle of
the register modification.
Fixes: 41691b8862 ("clk: bcm2835: Add support for programming the
audio domain clocks")
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 997f16bd5d upstream.
Current clamping of a normal divider allows a value < 1 to be valid.
A divider of < 1 would actually only be possible if we had a PLL...
So this patch clamps the divider to 1.
Fixes: 41691b8862 ("clk: bcm2835: Add support for programming the
audio domain clocks")
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6727f086cf upstream.
bcm2835_pll_off is currently assigning CM_PLL_ANARST to the control
register, which may lose the other bits that are currently set by the
clock dividers.
It also now locks during the read/modify/write cycle of both
registers.
Fixes: 41691b8862 ("clk: bcm2835: Add support for programming the
audio domain clocks")
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e708b383f4 upstream.
In poweroff, we set the reset bit and the power down bit, but only
managed to unset the reset bit for poweron. This meant that if HDMI
did -EPROBE_DEFER after it had grabbed its clocks, we'd power down the
PLLH (that had been on at boot time) and never recover.
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes: 41691b8862 ("clk: bcm2835: Add support for programming the audio domain clocks")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7387da520 upstream.
Commit 0b89e9aa28 (cpuidle: delay enabling interrupts until all
coupled CPUs leave idle) rightfully fixed a regression by letting
the coupled idle state framework to handle local interrupt enabling
when the CPU is exiting an idle state.
The current code checks if the idle state is coupled and, if so, it
will let the coupled code to enable interrupts. This way, it can
decrement the ready-count before handling the interrupt. This
mechanism prevents the other CPUs from waiting for a CPU which is
handling interrupts.
But the check is done against the state index returned by the back
end driver's ->enter functions which could be different from the
initial index passed as parameter to the cpuidle_enter_state()
function.
entered_state = target_state->enter(dev, drv, index);
[ ... ]
if (!cpuidle_state_is_coupled(drv, entered_state))
local_irq_enable();
[ ... ]
If the 'index' is referring to a coupled idle state but the
'entered_state' is *not* coupled, then the interrupts are enabled
again. All CPUs blocked on the sync barrier may busy loop longer
if the CPU has interrupts to handle before decrementing the
ready-count. That's consuming more energy than saving.
Fixes: 0b89e9aa28 (cpuidle: delay enabling interrupts until all coupled CPUs leave idle)
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
[ rjw: Subject & changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c998c07836 upstream.
Currently the 'registered' member of the cpuidle_device struct is set
to 1 during cpuidle_register_device. In this same function there are
checks to see if the device is already registered to prevent duplicate
calls to register the device, but this value is never set to 0 even on
unregister of the device. Because of this, any attempt to call
cpuidle_register_device after a call to cpuidle_unregister_device will
fail which shouldn't be the case.
To prevent this, set registered to 0 when the device is unregistered.
Fixes: c878a52d3c (cpuidle: Check if device is already registered)
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0ae3aeefab upstream.
As pm_runtime_set_active() may fail because the device's parent isn't
active, we can end up executing the ->runtime_resume() callback for the
device when it isn't allowed.
Fix this by invoking pm_runtime_set_active() before running the callback
and let's also deal with the error code.
Fixes: 37f204164d (PM: Add pm_runtime_suspend|resume_force functions)
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 41a3da2b8e upstream.
All configurations are lost and the registers will have
default values when the hardware is suspended and resumed,
so saving the private register space context on suspend, and
restoring it on resume.
Fixes: 4b45efe852 (mfd: Add support for Intel Sunrisepoint LPSS devices)
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a18afe809 upstream.
On ads7828 the internal reference defaults to off upon power up. When
using internal reference, it needs to be turned on and the voltage needs
to settle before normal conversion cycle can be started. Hence perform a
dummy read in the probe to enable the internal reference allowing the
voltage to settle before performing a normal read.
Without this fix, the first read from the ADC when using internal
reference always returns incorrect data.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 78cbccd3bd upstream.
When KDUMP is triggered the driver first talks to the firmware in INTX
mode, but the adapter firmware is still in MSIX mode. Therefore the first
driver command hangs since the driver is waiting for an INTX response and
firmware gives a MSIX response. If when the OS is installed on a RAID
drive created by the adapter KDUMP will hang since the driver does not
receive a response in sync mode.
Fixed by: Change the firmware to INTX mode if it is in MSIX mode before
sending the first sync command.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc4bf75ea3 upstream.
Typically under error conditions, it is possible for aac_command_thread()
to miss the wakeup from kthread_stop() and go back to sleep, causing it
to hang aac_shutdown.
In the observed scenario, the adapter is not functioning correctly and so
aac_fib_send() never completes (or time-outs depending on how it was
called). Shortly after aac_command_thread() starts it performs
aac_fib_send(SendHostTime) which hangs. When aac_probe_one
/aac_get_adapter_info send time outs, kthread_stop is called which breaks
the command thread out of it's hang.
The code will still go back to sleep in schedule_timeout() without
checking kthread_should_stop() so it causes aac_probe_one to hang until
the schedule_timeout() which is 30 minutes.
Fixed by: Adding another kthread_should_stop() before schedule_timeout()
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07beca2be2 upstream.
aac_fib_send has a special function case for initial commands during
driver initialization using wait < 0(pseudo sync mode). In this case,
the command does not sleep but rather spins checking for timeout.This
loop is calls cpu_relax() in an attempt to allow other processes/threads
to use the CPU, but this function does not relinquish the CPU and so the
command will hog the processor. This was observed in a KDUMP
"crashkernel" and that prevented the "command thread" (which is
responsible for completing the command from being timed out) from
starting because it could not get the CPU.
Fixed by replacing "cpu_relax()" call with "schedule()"
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 873ffe154a upstream.
In commit a269913c52 ("rtlwifi: Rework rtl_lps_leave() and
rtl_lps_enter() to use work queue"), the tests for enter/exit
power-save mode were inverted. With this change applied, the
wifi connection becomes much more stable.
Fixes: a269913c52 ("rtlwifi: Rework rtl_lps_leave() and rtl_lps_enter() to use work queue")
Signed-off-by: Wang YanQing <udknight@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit baa1702290 upstream.
The previous patch added an option to rtl8723be to manually select the
antenna for those cases when only a single antenna is present, and the
on-board EEPROM is incorrectly programmed. This patch implements the
necessary changes in the Bluetooth coexistence driver.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c18d8f5095 upstream.
A number of new laptops have been delivered with only a single antenna.
In principle, this is OK; however, a problem arises when the on-board
EEPROM is programmed to use the other antenna connection. The option
of opening the computer and moving the connector is not always possible
as it will void the warranty in some cases. In addition, this solution
breaks the Windows driver when the box dual boots Linux and Windows.
A fix involving a new module parameter has been developed. This commit
adds the new parameter and implements the changes needed for the driver.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f1925d78d7 upstream.
In case of timeout during read operation, the exit path lacked PM
runtime put. This could lead to unbalanced runtime PM usage counter thus
leaving the device in an active state.
Fixes: d7fd6075a2 ("hwrng: exynos - Add timeout for waiting on init done")
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b9bc799a4 upstream.
BugLink: http://bugs.launchpad.net/bugs/972604
Commit 09c9bae26b ("ath5k: add led pin
configuration for compaq c700 laptop") added a pin configuration for the Compaq
c700 laptop. However, the polarity of the led pin is reversed. It should be
red for wifi off and blue for wifi on, but it is the opposite. This bug was
reported in the following bug report:
http://pad.lv/972604
Fixes: 09c9bae26b ("ath5k: add led pin configuration for compaq c700 laptop")
Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4ad24a9d83 upstream.
It is observed that while loading and unloading ath10k modules
in an infinite loop, before ath10k_core_start() completion HTT
rx frames are received, while processing these frames,
dereferencing the arvifs list code is getting hit before
initilizing the arvifs list, causing a kernel panic.
This patch initilizes the arvifs list before initilizing htt.
Fixes the below issue:
[<bf88b058>] (ath10k_htt_rx_pktlog_completion_handler+0x278/0xd08 [ath10k_core])
[<bf88b058>] (ath10k_htt_rx_pktlog_completion_handler [ath10k_core])
[<bf88c0dc>] (ath10k_htt_txrx_compl_task+0x5f4/0xeb0 [ath10k_core])
[<bf88c0dc>] (ath10k_htt_txrx_compl_task [ath10k_core])
[<c0234100>] (tasklet_action+0x8c/0xec)
[<c0234100>] (tasklet_action)
[<c02337c0>] (__do_softirq+0xf8/0x228)
[<c02337c0>] (__do_softirq) [<c0233920>] (run_ksoftirqd+0x30/0x90)
Code: e5954ad8 e2899008 e1540009 0a00000d (e5943008)
---[ end trace 71de5c2e011dbf56 ]---
Kernel panic - not syncing: Fatal exception in interrupt
Fixes: 500ff9f938 ("ath10k: implement chanctx API")
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ce8c1484e upstream.
Upon firmware assert, restart work will be triggered so that mac80211
will reconfigure the driver. An issue is reported that after restart
work, survey dump data do not contain in-use (SURVEY_INFO_IN_USE) info
for operating channel. During reconfigure, since mac80211 already has
valid channel context for given radio, channel context iteration return
num_chanctx > 0. Hence rx_channel is always NULL. Fix this by assigning
channel context to rx_channel when driver restart is in progress.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a75fc5474 upstream.
commit 166de3f189 ("ath10k: remove supported chain mask") had revealed
an issue on monitor mode. Configuring NSS upon monitor interface
creation is causing target assert in all qca9888x and qca6174 firmware.
Firmware assert issue can be reproduced by below sequence even after
reverting commit 166de3f189 ("ath10k: remove supported chain mask").
ip link set wlan0 down
iw wlan0 set type monitor
iw phy0 set antenna 7
ip link set wlan0 up
This issue is originally reported on qca9888 with 10.1 firmware.
Fixes: 5572a95b4b ("ath10k: apply chainmask settings to vdev on creation")
Reported-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9ddc486aa0 upstream.
It is observed that, we are disabling the packet log if we write same
value to the pktlog_filter for the second time. Always enable pktlogs
on non zero filter.
Fixes: 90174455ae ("ath10k: add support to configure pktlog filter")
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3397c2c45b upstream.
A new element got inserted into enum mx35_clks with commit 3713e3f5e9
("clk: imx35: define two clocks for rtc"). This insertion shifted most
nummerical clock assignments to a new nummerical value which in turn
rendered most hardcoded nummeric values in imx35.dtsi incorrect.
Restore the existing order by moving the newly introduced clock to the
end of the enum. Update the dts documentation accordingly.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Fixes: 3713e3f5e9 ("clk: imx35: define two clocks for rtc")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ff5fa3c67 upstream.
After initially connecting a wired Xbox 360 controller or sending it
a command to change LEDs, a status/response packet is interpreted as
controller input. This causes the state of buttons represented in
byte 2 of the controller data packet to be incorrect until the next
valid input packet. Wireless Xbox 360 controllers are not affected.
Writing a new value to the LED device while holding the Start button
and running jstest is sufficient to reproduce this bug. An event will
come through with the Start button released.
Xboxdrv also won't attempt to read controller input from a packet
where byte 0 is non-zero. It also checks that byte 1 is 0x14, but
that value differs between wired and wireless controllers and this
code is shared by both. I think just checking byte 0 is enough to
eliminate unwanted packets.
The following are some examples of 3-byte status packets I saw:
01 03 02
02 03 00
03 03 03
08 03 00
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit affa80bd97 upstream.
When running a 32-bit userspace on a 64-bit kernel, the UI_SET_PHYS
ioctl needs to be treated with special care, as it has the pointer
size encoded in the command.
Signed-off-by: Ricky Liang <jcliang@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d3030d1196 upstream.
The ak4642 driver is using a regmap cache sync to restore the
configuration of the chip on resume but (as Peter observed) does not
actually define a register cache which means that the resume is never
going to work and we trigger asserts in regmap. Fix this by enabling
caching.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 01d6e08711 upstream.
Commit c8f33d0bec ("affs: kstrdup() memory handling") checks if the
kstrdup function returns NULL due to out-of-memory condition.
However, if we are remounting a filesystem with no change to
filesystem-specific options, the parameter data is NULL. In this case,
kstrdup returns NULL (because it was passed NULL parameter), although no
out of memory condition exists. The mount syscall then fails with
ENOMEM.
This patch fixes the bug. We fail with ENOMEM only if data is non-NULL.
The patch also changes the call to replace_mount_options - if we didn't
pass any filesystem-specific options, we don't call
replace_mount_options (thus we don't erase existing reported options).
Fixes: c8f33d0bec ("affs: kstrdup() memory handling")
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 94cc36b84a upstream.
Avoid an aliasing issue causing a build error in VDSO:
In file included from include/linux/srcu.h:34:0,
from include/linux/notifier.h:15,
from ./arch/mips/include/asm/uprobes.h:9,
from include/linux/uprobes.h:61,
from include/linux/mm_types.h:13,
from ./arch/mips/include/asm/vdso.h:14,
from arch/mips/vdso/vdso.h:27,
from arch/mips/vdso/gettimeofday.c:11:
include/linux/workqueue.h: In function 'work_static':
include/linux/workqueue.h:186:2: error: dereferencing type-punned pointer will break strict-aliasing rules [-Werror=strict-aliasing]
return *work_data_bits(work) & WORK_STRUCT_STATIC;
^
cc1: all warnings being treated as errors
make[2]: *** [arch/mips/vdso/gettimeofday.o] Error 1
with a CONFIG_DEBUG_OBJECTS_WORK configuration and GCC 5.2.0. Include
`-fno-strict-aliasing' along with compiler options used, as required for
kernel code, fixing a problem present since the introduction of VDSO
with commit ebb5e78cc6 ("MIPS: Initial implementation of a VDSO").
Thanks to Tejun for diagnosing this properly!
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Fixes: ebb5e78cc6 ("MIPS: Initial implementation of a VDSO")
Cc: Tejun Heo <tj@kernel.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13357/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 13eb192d10 upstream.
In microMIPS kernels, handle_signal() sets the isa16 mode bit in the
vdso address so that the sigreturn trampolines (which are offset from
the VDSO) get executed as microMIPS.
However commit ebb5e78cc6 ("MIPS: Initial implementation of a VDSO")
changed the offsets to come from the VDSO image, which already have the
isa16 mode bit set correctly since they're extracted from the VDSO
shared library symbol table.
Drop the isa16 mode bit handling from handle_signal() to fix sigreturn
for cores which support both microMIPS and normal MIPS. This doesn't fix
microMIPS only cores, since the VDSO is still built for normal MIPS, but
thats a separate problem.
Fixes: ebb5e78cc6 ("MIPS: Initial implementation of a VDSO")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13348/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit abf378be49 upstream.
Correct the cases missed with commit 9b26616c8d ("MIPS: Respect the
ISA level in FCSR handling") and prevent writes to read-only FCSR bits
there.
This in particular applies to FP context initialisation where any IEEE
754-2008 bits preset by `mips_set_personality_nan' are cleared before
the relevant ptrace(2) call takes effect and the PTRACE_POKEUSR request
addressing FPC_CSR where no masking of read-only FCSR bits is done.
Remove the FCSR clearing from FP context initialisation then and unify
PTRACE_POKEUSR/FPC_CSR and PTRACE_SETFPREGS handling, by factoring out
code from `ptrace_setfpregs' and calling it from both places.
This mostly matters to soft float configurations where the emulator can
be switched this way to a mode which should not be accessible and cannot
be set with the CTC1 instruction. With hard float configurations any
effect is transient anyway as read-only bits will retain their values at
the time the FP context is restored.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13239/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4249548454 upstream.
Fix a floating-point context restoration regression introduced with
commit 9b26616c8d ("MIPS: Respect the ISA level in FCSR handling")
that causes a Floating Point exception and consequently a kernel oops
with hard float configurations when one or more FCSR Enable and their
corresponding Cause bits are set both at a time via a ptrace(2) call.
To do so reinstate Cause bit masking originally introduced with commit
b1442d39fa ("MIPS: Prevent user from setting FCSR cause bits") to
address this exact problem and then inadvertently removed from the
PTRACE_SETFPREGS request with the commit referred above.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13238/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6533af4d48 upstream.
If a kernel doesn't support MSA context (ie. CONFIG_CPU_HAS_MSA=n) then
it will only keep 64 bits per FP register in thread context, and the
calls to set_fpr64 in restore_msa_extcontext will overrun the end of the
FP register context into the FCSR & MSACSR values. GCC 6.x has become
smart enough to detect this & complain like so:
arch/mips/kernel/signal.c: In function 'protected_restore_fp_context':
./arch/mips/include/asm/processor.h:114:17: error: array subscript is above array bounds [-Werror=array-bounds]
fpr->val##width[FPR_IDX(width, idx)] = val; \
~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~
./arch/mips/include/asm/processor.h:118:1: note: in expansion of macro 'BUILD_FPR_ACCESS'
BUILD_FPR_ACCESS(64)
The only way to trigger this code to run would be for a program to set
up an artificial extended MSA context structure following a sigframe &
execute sigreturn. Whilst this doesn't allow a program to write to any
state that it couldn't already, it makes little sense to allow this
"restoration" of MSA context in a system that doesn't support MSA.
Fix this by killing a program with SIGSYS if it tries something as crazy
as "restoring" fake MSA context in this way, also fixing the build error
& allowing for most of restore_msa_extcontext to be optimised out of
kernels without support for MSA.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reported-by: Michal Toman <michal.toman@imgtec.com>
Fixes: bf82cb30c7 ("MIPS: Save MSA extended context around signals")
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Michal Toman <michal.toman@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13164/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a3c8b48ac upstream.
In revision 1.12 of the MSA specification, the copy_u.w instruction has
been removed for MIPS32 & the copy_u.d instruction has been removed for
MIPS64. Newer toolchains (eg. Codescape SDK essentials 2015.10) will
complain about this like so:
arch/mips/kernel/r4k_fpu.S:290: Error: opcode not supported on this
processor: mips32r2 (mips32r2) `copy_u.w $1,$w26[3]'
Since we always copy to the width of a GPR, simply use copy_s instead of
copy_u to fix this.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13061/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f5b556c94c upstream.
This makes the ath79 bootconsole behave the same way as the generic 8250
bootconsole.
Also waiting for TEMT (transmit buffer is empty) instead of just THRE
(transmit buffer is not full) ensures that all characters have been
transmitted before the real serial driver starts reconfiguring the serial
controller (which would sometimes result in garbage being transmitted.)
This change does not cause a visible performance loss.
In addition, this seems to fix a hang observed in certain configurations on
many AR7xxx/AR9xxx SoCs during autoconfig of the real serial driver.
A more complete follow-up patch will disable 8250 autoconfig for ath79
altogether (the serial controller is detected as a 16550A, which is not
fully compatible with the ath79 serial, and the autoconfig may lead to
undefined behavior on ath79.)
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 37d22a0d79 upstream.
It's possible for pages to become visible prior to update_mmu_cache
running if a thread within the same address space preempts the current
thread or runs simultaneously on another CPU. That is, the following
scenario is possible:
CPU0 CPU1
write to page
flush_dcache_page
flush_icache_page
set_pte_at
map page
update_mmu_cache
If CPU1 maps the page in between CPU0's set_pte_at, which marks it valid
& visible, and update_mmu_cache where the dcache flush occurs then CPU1s
icache will fill from stale data (unless it fills from the dcache, in
which case all is good, but most MIPS CPUs don't have this property).
Commit 4d46a67a3e ("MIPS: Fix race condition in lazy cache flushing.")
attempted to fix that by performing the dcache flush in
flush_icache_page such that it occurs before the set_pte_at call makes
the page visible. However it has the problem that not all code that
writes to pages exposed to userland call flush_icache_page. There are
many callers of set_pte_at under mm/ and only 2 of them do call
flush_icache_page. Thus the race window between a page becoming visible
& being coherent between the icache & dcache remains open in some cases.
To illustrate some of the cases, a WARN was added to __update_cache with
this patch applied that triggered in cases where a page about to be
flushed from the dcache was not the last page provided to
flush_icache_page. That is, backtraces were obtained for cases in which
the race window is left open without this patch. The 2 standout examples
follow.
When forking a process:
[ 15.271842] [<80417630>] __update_cache+0xcc/0x188
[ 15.277274] [<80530394>] copy_page_range+0x56c/0x6ac
[ 15.282861] [<8042936c>] copy_process.part.54+0xd40/0x17ac
[ 15.289028] [<80429f80>] do_fork+0xe4/0x420
[ 15.293747] [<80413808>] handle_sys+0x128/0x14c
When exec'ing an ELF binary:
[ 14.445964] [<80417630>] __update_cache+0xcc/0x188
[ 14.451369] [<80538d88>] move_page_tables+0x414/0x498
[ 14.457075] [<8055d848>] setup_arg_pages+0x220/0x318
[ 14.462685] [<805b0f38>] load_elf_binary+0x530/0x12a0
[ 14.468374] [<8055ec3c>] search_binary_handler+0xbc/0x214
[ 14.474444] [<8055f6c0>] do_execveat_common+0x43c/0x67c
[ 14.480324] [<8055f938>] do_execve+0x38/0x44
[ 14.485137] [<80413808>] handle_sys+0x128/0x14c
These code paths write into a page, call flush_dcache_page then call
set_pte_at without flush_icache_page inbetween. The end result is that
the icache can become corrupted & userland processes may execute
unexpected or invalid code, typically resulting in a reserved
instruction exception, a trap or a segfault.
Fix this race condition fully by performing any cache maintenance
required to keep the icache & dcache in sync in set_pte_at, before the
page is made valid. This has the added bonus of ensuring the cache
maintenance always happens in one location, rather than being duplicated
in flush_icache_page & update_mmu_cache. It also matches the way other
architectures solve the same problem (see arm, ia64 & powerpc).
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reported-by: Ionela Voinescu <ionela.voinescu@imgtec.com>
Cc: Lars Persson <lars.persson@axis.com>
Fixes: 4d46a67a3e ("MIPS: Fix race condition in lazy cache flushing.")
Cc: Steven J. Hill <sjhill@realitydiluted.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12722/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 234859e49a upstream.
When flush_dcache_page is called on an executable page, that page is
about to be provided to userland & we can presume that the icache
contains no valid entries for its address range. However if the icache
does not fill from the dcache then we cannot presume that the pages
content has been written back as far as the memories that the dcache
will fill from (ie. L2 or further out).
This was being done for lowmem pages, but not for highmem which can lead
to icache corruption. Fix this by mapping highmem pages & flushing their
content from the dcache in __flush_dcache_page before providing the page
to userland, just as is done for lowmem pages.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Lars Persson <lars.persson@axis.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12720/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a7e89326b4 upstream.
Commit f51246efee ("MIPS: Get rid of finish_arch_switch().") moved the
__restore_watch() call from finish_arch_switch() (i.e. after resume()
returns) to before the resume() call in switch_to(). This results in
watchpoints only being restored when a task is descheduled, preventing
the watchpoints from being effective most of the time, except due to
chance before the watchpoints are lazily removed.
Fix the call sequence from switch_to() through to
mips_install_watch_registers() to pass the task_struct pointer of the
next task, instead of using current. This allows the watchpoints for the
next (non-current) task to be restored without reintroducing
finish_arch_switch().
Fixes: f51246efee ("MIPS: Get rid of finish_arch_switch().")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12726/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 987e5b8344 upstream.
Since commit 8cb48fe169 ("MIPS: Provide correct siginfo_t.si_stime"),
MIPS' uapi/asm/siginfo.h has included uapi/asm-generic/siginfo.h
directly before defining MIPS' struct siginfo, in order to get the
necessary definitions needed for the siginfo struct without the generic
copy_siginfo() hitting compiler errors due to struct siginfo not yet
being defined.
Now that the generic copy_siginfo() is moved out to linux/signal.h we
can safely include asm-generic/siginfo.h before defining the MIPS
specific struct siginfo, which avoids the uapi/ include as well as
breakage due to generic copy_siginfo() being defined before struct
siginfo.
Reported-by: Christopher Ferris <cferris@google.com>
Fixes: 8cb48fe169 ("MIPS: Provide correct siginfo_t.si_stime")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Petr Malat <oss@malat.biz>
Cc: linux-mips@linux-mips.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81a76d7119 upstream.
When showing backtraces in response to traps, for example crashes and
address errors (usually unaligned accesses) when they are set in debugfs
to be reported, unwind_stack will be used if the PC was in the kernel
text address range. However since EVA it is possible for user and kernel
address ranges to overlap, and even without EVA userland can still
trigger an address error by jumping to a KSeg0 address.
Adjust the check to also ensure that it was running in kernel mode. I
don't believe any harm can come of this problem, since unwind_stack() is
sufficiently defensive, however it is only meant for unwinding kernel
code, so to be correct it should use the raw backtracing instead.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11701/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
(cherry picked from commit d2941a975ac745c607dfb590e92bb30bc352dad9)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a816b306c6 upstream.
When unwinding through IRQs and exceptions, the unwinding only continues
if the PC is a kernel text address, however since EVA it is possible for
user and kernel address ranges to overlap, potentially allowing
unwinding to continue to user mode if the user PC happens to be in the
kernel text address range.
Adjust the check to also ensure that the register state from before the
exception is actually running in kernel mode, i.e. !user_mode(regs).
I don't believe any harm can come of this problem, since the PC is only
output, the stack pointer is checked to ensure it resides within the
task's stack page before it is dereferenced in search of the return
address, and the return address register is similarly only output (if
the PC is in a leaf function or the beginning of a non-leaf function).
However unwind_stack() is only meant for unwinding kernel code, so to be
correct the unwind should stop there.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11700/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e49d384885 upstream.
Fix a build regression from commit c9017757c5 ("MIPS: init upper 64b
of vector registers when MSA is first used"):
arch/mips/built-in.o: In function `enable_restore_fp_context':
traps.c:(.text+0xbb90): undefined reference to `_init_msa_upper'
traps.c:(.text+0xbb90): relocation truncated to fit: R_MIPS_26 against `_init_msa_upper'
traps.c:(.text+0xbef0): undefined reference to `_init_msa_upper'
traps.c:(.text+0xbef0): relocation truncated to fit: R_MIPS_26 against `_init_msa_upper'
to !CONFIG_CPU_HAS_MSA configurations with older GCC versions, which are
unable to figure out that calls to `_init_msa_upper' are indeed dead.
Of the many ways to tackle this failure choose the approach we have
already taken in `thread_msa_context_live'.
[ralf@linux-mips.org: Drop patch segment to junk file.]
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13271/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ab4a92e667 upstream.
When emulating a jalr instruction with rd == $0, the code in
isBranchInstr was incorrectly writing to GPR $0 which should actually
always remain zeroed. This would lead to any further instructions
emulated which use $0 operating on a bogus value until the task is next
context switched, at which point the value of $0 in the task context
would be restored to the correct zero by a store in SAVE_SOME. Fix this
by not writing to rd if it is $0.
Fixes: 102cedc32a ("MIPS: microMIPS: Floating point support.")
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Maciej W. Rozycki <macro@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13160/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c9c6837d39 upstream.
gcc-6 started warning by default about variables that are not
used anywhere and that are marked 'const', generating many
false positives in an allmodconfig build, e.g.:
arch/arm/mach-davinci/board-da830-evm.c:282:20: warning: 'da830_evm_emif25_pins' defined but not used [-Wunused-const-variable=]
arch/arm/plat-omap/dmtimer.c:958:34: warning: 'omap_timer_match' defined but not used [-Wunused-const-variable=]
drivers/bluetooth/hci_bcm.c:625:39: warning: 'acpi_bcm_default_gpios' defined but not used [-Wunused-const-variable=]
drivers/char/hw_random/omap-rng.c:92:18: warning: 'reg_map_omap4' defined but not used [-Wunused-const-variable=]
drivers/devfreq/exynos/exynos5_bus.c:381:32: warning: 'exynos5_busfreq_int_pm' defined but not used [-Wunused-const-variable=]
drivers/dma/mv_xor.c:1139:34: warning: 'mv_xor_dt_ids' defined but not used [-Wunused-const-variable=]
This is similar to the existing -Wunused-but-set-variable warning
that was added in an earlier release and that we disable by default
now and only enable when W=1 is set, so it makes sense to do
the same here. Once we have eliminated the majority of the
warnings for both, we can put them back into the default list.
We probably want this in backport kernels as well, to allow building
them with gcc-6 without introducing extra warnings.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Michal Marek <mmarek@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 305c2e71b3 upstream.
Now that we've done a more comprehensive fix with the intermediate
target state we can remove the previous hack introduced with commit
90a88d6ef8 ("scsi: fix soft lockup in scsi_remove_target() on module
removal").
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f05795d3d7 upstream.
Add intermediate STARGET_REMOVE state to scsi_target_state to avoid
running into the BUG_ON() in scsi_target_reap(). The STARGET_REMOVE
state is only valid in the path from scsi_remove_target() to
scsi_target_destroy() indicating this target is going to be removed.
This re-fixes the problem introduced in commits bc3f02a795 ("[SCSI]
scsi_remove_target: fix softlockup regression on hot remove") and
4099819356 ("scsi: restart list search after unlock in
scsi_remove_target") in a more comprehensive way.
[mkp: Included James' fix for scsi_target_destroy()]
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Fixes: 4099819356
Reported-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Tested-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: James Bottomley <jejb@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 037369b872 upstream.
The HPFS filesystem used generic_show_options to produce string that is
displayed in /proc/mounts. However, there is a problem that the options
may disappear after remount. If we mount the filesystem with option1
and then remount it with option2, /proc/mounts should show both option1
and option2, however it only shows option2 because the whole option
string is replaced with replace_mount_options in hpfs_remount_fs.
To fix this bug, implement the hpfs_show_options function that prints
options that are currently selected.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 44d51706b4 upstream.
Commit ce657611ba ("hpfs: kstrdup() out of memory handling") checks if
the kstrdup function returns NULL due to out-of-memory condition.
However, if we are remounting a filesystem with no change to
filesystem-specific options, the parameter data is NULL. In this case,
kstrdup returns NULL (because it was passed NULL parameter), although no
out of memory condition exists. The mount syscall then fails with
ENOMEM.
This patch fixes the bug. We fail with ENOMEM only if data is non-NULL.
The patch also changes the call to replace_mount_options - if we didn't
pass any filesystem-specific options, we don't call
replace_mount_options (thus we don't erase existing reported options).
Fixes: ce657611ba ("hpfs: kstrdup() out of memory handling")
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1900149c83 upstream.
Ezequiel reported that he's facing UBI going into read-only
mode after power cut. It turned out that this behavior happens
only when updating a static volume is interrupted and Fastmap is
used.
A possible trace can look like:
ubi0 warning: ubi_io_read_vid_hdr [ubi]: no VID header found at PEB 2323, only 0xFF bytes
ubi0 warning: ubi_eba_read_leb [ubi]: switch to read-only mode
CPU: 0 PID: 833 Comm: ubiupdatevol Not tainted 4.6.0-rc2-ARCH #4
Hardware name: SAMSUNG ELECTRONICS CO., LTD. 300E4C/300E5C/300E7C/NP300E5C-AD8AR, BIOS P04RAP 10/15/2012
0000000000000286 00000000eba949bd ffff8800c45a7b38 ffffffff8140d841
ffff8801964be000 ffff88018eaa4800 ffff8800c45a7bb8 ffffffffa003abf6
ffffffff850e2ac0 8000000000000163 ffff8801850e2ac0 ffff8801850e2ac0
Call Trace:
[<ffffffff8140d841>] dump_stack+0x63/0x82
[<ffffffffa003abf6>] ubi_eba_read_leb+0x486/0x4a0 [ubi]
[<ffffffffa00453b3>] ubi_check_volume+0x83/0xf0 [ubi]
[<ffffffffa0039d97>] ubi_open_volume+0x177/0x350 [ubi]
[<ffffffffa00375d8>] vol_cdev_open+0x58/0xb0 [ubi]
[<ffffffff8124b08e>] chrdev_open+0xae/0x1d0
[<ffffffff81243bcf>] do_dentry_open+0x1ff/0x300
[<ffffffff8124afe0>] ? cdev_put+0x30/0x30
[<ffffffff81244d36>] vfs_open+0x56/0x60
[<ffffffff812545f4>] path_openat+0x4f4/0x1190
[<ffffffff81256621>] do_filp_open+0x91/0x100
[<ffffffff81263547>] ? __alloc_fd+0xc7/0x190
[<ffffffff812450df>] do_sys_open+0x13f/0x210
[<ffffffff812451ce>] SyS_open+0x1e/0x20
[<ffffffff81a99e32>] entry_SYSCALL_64_fastpath+0x1a/0xa4
UBI checks static volumes for data consistency and reads the
whole volume upon first open. If the volume is found erroneous
users of UBI cannot read from it, but another volume update is
possible to fix it. The check is performed by running
ubi_eba_read_leb() on every allocated LEB of the volume.
For static volumes ubi_eba_read_leb() computes the checksum of all
data stored in a LEB. To verify the computed checksum it has to read
the LEB's volume header which stores the original checksum.
If the volume header is not found UBI treats this as fatal internal
error and switches to RO mode. If the UBI device was attached via a
full scan the assumption is correct, the volume header has to be
present as it had to be there while scanning to get known as mapped.
If the attach operation happened via Fastmap the assumption is no
longer correct. When attaching via Fastmap UBI learns the mapping
table from Fastmap's snapshot of the system state and not via a full
scan. It can happen that a LEB got unmapped after a Fastmap was
written to the flash. Then UBI can learn the LEB still as mapped and
accessing it returns only 0xFF bytes. As UBI is not a FTL it is
allowed to have mappings to empty PEBs, it assumes that the layer
above takes care of LEB accounting and referencing.
UBIFS does so using the LEB property tree (LPT).
For static volumes UBI blindly assumes that all LEBs are present and
therefore special actions have to be taken.
The described situation can happen when updating a static volume is
interrupted, either by a user or a power cut.
The volume update code first unmaps all LEBs of a volume and then
writes LEB by LEB. If the sequence of operations is interrupted UBI
detects this either by the absence of LEBs, no volume header present
at scan time, or corrupted payload, detected via checksum.
In the Fastmap case the former method won't trigger as no scan
happened and UBI automatically thinks all LEBs are present.
Only by reading data from a LEB it detects that the volume header is
missing and incorrectly treats this as fatal error.
To deal with the situation ubi_eba_read_leb() from now on checks
whether we attached via Fastmap and handles the absence of a
volume header like a data corruption error.
This way interrupted static volume updates will correctly get detected
also when Fastmap is used.
Reported-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca9eb49aa9 upstream.
The generic copy_siginfo() is currently defined in
asm-generic/siginfo.h, after including uapi/asm-generic/siginfo.h which
defines the generic struct siginfo. However this makes it awkward for an
architecture to use it if it has to define its own struct siginfo (e.g.
MIPS and potentially IA64), since it means that asm-generic/siginfo.h
can only be included after defining the arch-specific siginfo, which may
be problematic if the arch-specific definition needs definitions from
uapi/asm-generic/siginfo.h.
It is possible to work around this by first including
uapi/asm-generic/siginfo.h to get the constants before defining the
arch-specific siginfo, and include asm-generic/siginfo.h after. However
uapi headers can't be included by other uapi headers, so that first
include has to be in an ifdef __kernel__, with the non __kernel__ case
including the non-UAPI header instead.
Instead of that mess, move the generic copy_siginfo() definition into
linux/signal.h, which allows an arch-specific uapi/asm/siginfo.h to
include asm-generic/siginfo.h and define the arch-specific siginfo, and
for the generic copy_siginfo() to see that arch-specific definition.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Petr Malat <oss@malat.biz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Christopher Ferris <cferris@google.com>
Cc: linux-arch@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-ia64@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12478/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2ffa9a5d76 upstream.
If tb_drom_read() fails, sw->drom is freed but not set to NULL. sw->drom
is then freed again in the error path of tb_switch_alloc().
The bug can be triggered by unplugging a thunderbolt device shortly after
it is detected by the thunderbolt driver.
Clear sw->drom if tb_drom_read() fails.
[bhelgaas: add Fixes:, stable versions of interest]
Fixes: 343fcb8c70 ("thunderbolt: Fix nontrivial endpoint devices.")
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 86c72d1ce9 upstream.
Add the pin configuration value of this machine into the pin_quirk
table to make DELL1_MIC_NO_PRESENCE apply to this machine.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 423cd78561 upstream.
The headphone has noise when playing sound or switching microphone sources.
It uses the same codec on XPS 13 9350, but with different subsystem ID.
Applying the fixup can solve the issue.
Also, changing the model name to better differentiate models.
v2: Reorder by device ID.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dcd4f0db61 upstream.
Support new codecs for ALC234/ALC274/ALC294.
This three codecs was the same IC.
But bonding is not the same.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f75564d343 upstream.
The bar number is found in reg2 within the gdd. Therefore
we need to change the assigment from reg1 to reg2 which
is the correct location.
Signed-off-by: Andreas Werner <andreas.werner@men.de>
Fixes: '3764e82e5' drivers: Introduce MEN Chameleon Bus
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46856fabe4 upstream.
Commits 190aa4304d (Add AMD Mullins platform support) and
cca118fa2a (Add AMD Carrizo platform support) enabled the
driver on a lot more devices, but the following commit missed
a single location in the code when checking if the SB800 register
offsets should be used. This leads to the wrong register being
written which in turn causes ACPI to go haywire.
Fix this by introducing a helper function to check for the new
register layout and use this consistently.
https://bugzilla.kernel.org/show_bug.cgi?id=114201https://bugzilla.redhat.com/show_bug.cgi?id=1329910
Fixes: bdecfcdb54 (sp5100_tco: fix the device check for SB800
and later chipsets)
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ec36a5c668 upstream.
Add missing locking to:
* bcm2835_pll_divider_on
* bcm2835_pll_divider_off
to protect the read modify write cycle for the
register access protecting both cm_reg and a2w_reg
registers.
Fixes: 41691b8862 ("clk: bcm2835: Add support for programming the
audio domain clocks")
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54cf809b95 upstream.
Similar to commits:
51d7d5205d ("powerpc: Add smp_mb() to arch_spin_is_locked()")
d86b8da04d ("arm64: spinlock: serialise spin_unlock_wait against concurrent lockers")
qspinlock suffers from the fact that the _Q_LOCKED_VAL store is
unordered inside the ACQUIRE of the lock.
And while this is not a problem for the regular mutual exclusive
critical section usage of spinlocks, it breaks creative locking like:
spin_lock(A) spin_lock(B)
spin_unlock_wait(B) if (!spin_is_locked(A))
do_something() do_something()
In that both CPUs can end up running do_something at the same time,
because our _Q_LOCKED_VAL store can drop past the spin_unlock_wait()
spin_is_locked() loads (even on x86!!).
To avoid making the normal case slower, add smp_mb()s to the less used
spin_unlock_wait() / spin_is_locked() side of things to avoid this
problem.
Reported-and-tested-by: Davidlohr Bueso <dave@stgolabs.net>
Reported-by: Giovanni Gherdovich <ggherdovich@suse.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b8995f527a upstream.
This patch fixes the broken serial log when changing the clock source
of uart device. Before disabling the original clock source, this patch
enables the new clock source to protect the clock off state for a split second.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
commit c42850f1ae upstream.
There is a special register that shows interrupt status by source. In
particular case the source can be a combination of DMA Tx, DMA Rx, and UART.
Read the register and call the handlers only for sources that request an
interrupt.
Fixes: 6ede6dcd87 ("serial: 8250_mid: add support for DMA engine handling from UART MMIO")
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 107e15fc1f upstream.
Unlike Intel Medfield and Tangier platforms DNV uses PCI BAR0 for IO compatible
resources and BAR1 for MMIO. We need latter in a way to support DMA. Introduce
an additional field in the internal structure and pass PCI BAR based on device
ID.
Reported-by: "Lai, Poey Seng" <poey.seng.lai@intel.com>
Fixes: 6ede6dcd87 ("serial: 8250_mid: add support for DMA engine handling from UART MMIO")
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f210c18c1 upstream.
Since commit 21947ba654 ("serial: 8250_pci: replace switch-case by
formula"), the 8250 driver crashes in the byt_set_termios() function
with a divide error. This is caused by the fact that a baud rate of 0 (B0)
is not handled properly. Fix it by falling back to B9600 in this case.
Signed-off-by: David Müller <d.mueller@elsoft.ch>
Fixes: 21947ba654 ("serial: 8250_pci: replace switch-case by formula")
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5be605ac9a upstream.
Commit 1cf6e8fc83 ("tty/serial: at91: fix RTS line management when
hardware handshake is enabled") actually allowed to enable hardware
handshaking.
Before, the CRTSCTS flags was silently ignored.
As the DMA controller can't drive RTS (as explain in the commit message).
Ensure that hardware flow control stays disabled when DMA is used and FIFOs
are not available.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Fixes: 1cf6e8fc83 ("tty/serial: at91: fix RTS line management when hardware handshake is enabled")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d175feca89 upstream.
Dmitry reported, that the current cleanup code in n_gsm can trigger a
warning:
WARNING: CPU: 2 PID: 24238 at drivers/tty/n_gsm.c:2048 gsm_cleanup_mux+0x166/0x6b0()
...
Call Trace:
...
[<ffffffff81247ab9>] warn_slowpath_null+0x29/0x30 kernel/panic.c:490
[<ffffffff828d0456>] gsm_cleanup_mux+0x166/0x6b0 drivers/tty/n_gsm.c:2048
[<ffffffff828d4d87>] gsmld_open+0x5b7/0x7a0 drivers/tty/n_gsm.c:2386
[<ffffffff828b9078>] tty_ldisc_open.isra.2+0x78/0xd0 drivers/tty/tty_ldisc.c:447
[<ffffffff828b973a>] tty_set_ldisc+0x1ca/0xa70 drivers/tty/tty_ldisc.c:567
[< inline >] tiocsetd drivers/tty/tty_io.c:2650
[<ffffffff828a14ea>] tty_ioctl+0xb2a/0x2140 drivers/tty/tty_io.c:2883
...
But this is a legal path when open fails to find a space in the
gsm_mux array and tries to clean up. So make it a standard test
instead of a warning.
Reported-by: "Dmitry Vyukov" <dvyukov@google.com>
Cc: Alan Cox <alan@linux.intel.com>
Link: http://lkml.kernel.org/r/CACT4Y+bHQbAB68VFi7Romcs-Z9ZW3kQRvcq+BvHH1oa5NcAdLA@mail.gmail.com
Fixes: 5a640967 ("tty/n_gsm.c: fix a memory leak in gsmld_open()")
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6798df4c5f upstream.
When csw->con_startup() fails in do_register_con_driver, we return no
error (i.e. 0). This was changed back in 2006 by commit 3e795de763.
Before that we used to return -ENODEV.
So fix the return value to be -ENODEV in that case again.
Fixes: 3e795de763 ("VT binding: Add binding/unbinding support for the VT console")
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: "Dan Carpenter" <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 702f926067 upstream.
b4ff8389ed is incomplete: relies on nr_legacy_irqs() to get the number
of legacy interrupts when actually nr_legacy_irqs() returns 0 after
probe_8259A(). Use NR_IRQS_LEGACY instead.
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 316314cae1 upstream.
This ensures that the guest doesn't see XSAVE extensions
(e.g. xgetbv1 or xsavec) that the host lacks.
Cc: stable@vger.kernel.org
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
[4.5 does have CPUID_D_1_EAX, but earlier kernels don't, so use
the numeric value. This is consistent with other occurrences
of cpuid_mask in arch/x86/kvm/cpuid.c - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b45bacd2d0 upstream.
Writing CP0_Compare clears the timer interrupt pending bit
(CP0_Cause.TI), but this wasn't being done atomically. If a timer
interrupt raced with the write of the guest CP0_Compare, the timer
interrupt could end up being pending even though the new CP0_Compare is
nowhere near CP0_Count.
We were already updating the hrtimer expiry with
kvm_mips_update_hrtimer(), which used both kvm_mips_freeze_hrtimer() and
kvm_mips_resume_hrtimer(). Close the race window by expanding out
kvm_mips_update_hrtimer(), and clearing CP0_Cause.TI and setting
CP0_Compare between the freeze and resume. Since the pending timer
interrupt should not be cleared when CP0_Compare is written via the KVM
user API, an ack argument is added to distinguish the source of the
write.
Fixes: e30492bbe9 ("MIPS: KVM: Rewrite count/compare timer emulation")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim KrÄmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4355c44f06 upstream.
There's a particularly narrow and subtle race condition when the
software emulated guest timer is frozen which can allow a guest timer
interrupt to be missed.
This happens due to the hrtimer expiry being inexact, so very
occasionally the freeze time will be after the moment when the emulated
CP0_Count transitions to the same value as CP0_Compare (so an IRQ should
be generated), but before the moment when the hrtimer is due to expire
(so no IRQ is generated). The IRQ won't be generated when the timer is
resumed either, since the resume CP0_Count will already match CP0_Compare.
With VZ guests in particular this is far more likely to happen, since
the soft timer may be frozen frequently in order to restore the timer
state to the hardware guest timer. This happens after 5-10 hours of
guest soak testing, resulting in an overflow in guest kernel timekeeping
calculations, hanging the guest. A more focussed test case to
intentionally hit the race (with the help of a new hypcall to cause the
timer state to migrated between hardware & software) hits the condition
fairly reliably within around 30 seconds.
Instead of relying purely on the inexact hrtimer expiry to determine
whether an IRQ should be generated, read the guest CP0_Compare and
directly check whether the freeze time is before or after it. Only if
CP0_Count is on or after CP0_Compare do we check the hrtimer expiry to
determine whether the last IRQ has already been generated (which will
have pushed back the expiry by one timer period).
Fixes: e30492bbe9 ("MIPS: KVM: Rewrite count/compare timer emulation")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim KrÄmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f24632475d upstream.
Commit d28bc9dd25 reversed the order of two lines which initialize cr0,
allowing the current (old) cr0 value to mess up vcpu initialization.
This was observed in the checks for cr0 X86_CR0_WP bit in the context of
kvm_mmu_reset_context(). Besides, setting vcpu->arch.cr0 after vmx_set_cr0()
is completely redundant. Change the order back to ensure proper vcpu
initialization.
The combination of booting with ovmf firmware when guest vcpus > 1 and kvm's
ept=N option being set results in a VM-entry failure. This patch fixes that.
Fixes: d28bc9dd25 ("KVM: x86: INIT and reset sequences are different")
Signed-off-by: Bruce Rogers <brogers@suse.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9842df6200 upstream.
MSR 0x2f8 accessed the 124th Variable Range MTRR ever since MTRR support
was introduced by 9ba075a664 ("KVM: MTRR support").
0x2f8 became harmful when 910a6aae4e ("KVM: MTRR: exactly define the
size of variable MTRRs") shrinked the array of VR MTRRs from 256 to 8,
which made access to index 124 out of bounds. The surrounding code only
WARNs in this situation, thus the guest gained a limited read/write
access to struct kvm_arch_vcpu.
0x2f8 is not a valid VR MTRR MSR, because KVM has/advertises only 16 VR
MTRR MSRs, 0x200-0x20f. Every VR MTRR is set up using two MSRs, 0x2f8
was treated as a PHYSBASE and 0x2f9 would be its PHYSMASK, but 0x2f9 was
not implemented in KVM, therefore 0x2f8 could never do anything useful
and getting rid of it is safe.
This fixes CVE-2016-3713.
Fixes: 910a6aae4e ("KVM: MTRR: exactly define the size of variable MTRRs")
Reported-by: David Matlack <dmatlack@google.com>
Signed-off-by: Andy Honig <ahonig@google.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d375278d66 upstream.
DMA is optional with this driver. If it was not enabled the devpriv->dma
pointer will be NULL.
Fix the possible NULL pointer dereference when trying to disable the DMA
channels in das1800_ai_cancel() and tidy up the comments to fix the
checkpatch.pl issues:
WARNING: line over 80 characters
It's probably harmless in das1800_ai_setup_dma() because the 'desc' pointer
will not be used if DMA is disabled but fix it there also.
Fixes: 99dfc3357e ("staging: comedi: das1800: remove depends on ISA_DMA_API limitation")
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5096c4d3bf upstream.
The argument of dev_err() in usb_gadget_map_request() should be dev
instead of &gadget->dev.
Fixes: 7ace8fc ("usb: gadget: udc: core: Fix argument of dma_map_single for IOMMU")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6fb650d43d upstream.
When a USB driver is bound to an interface (either through probing or
by claiming it) or is unbound from an interface, the USB core always
disables Link Power Management during the transition and then
re-enables it afterward. The reason is because the driver might want
to prevent hub-initiated link power transitions, in which case the HCD
would have to recalculate the various LPM parameters. This
recalculation takes place when LPM is re-enabled and the new
parameters are sent to the device and its parent hub.
However, if the driver does not want to prevent hub-initiated link
power transitions then none of this work is necessary. The parameters
don't need to be recalculated, and LPM doesn't need to be disabled and
re-enabled.
It turns out that disabling and enabling LPM can be time-consuming,
enough so that it interferes with user programs that want to claim and
release interfaces rapidly via usbfs. Since the usbfs kernel driver
doesn't set the disable_hub_initiated_lpm flag, we can speed things up
and get the user programs to work by leaving LPM alone whenever the
flag isn't set.
And while we're improving the way disable_hub_initiated_lpm gets used,
let's also fix its kerneldoc.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Matthew Giassa <matthew@giassa.net>
CC: Mathias Nyman <mathias.nyman@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cdc77c82a8 upstream.
The current implemenentation restart the sent pattern for each entry in
the sg list. The receiving end expects a continuous pattern, and test
will fail unless scatterilst entries happen to be aligned with the
pattern
Fix this by calculating the pattern byte based on total sent size
instead of just the current sg entry.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Fixes: 8b52490193 ("[PATCH] USB: usbtest: scatterlist OUT data pattern testing")
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f78bbcae86 upstream.
When binding the function to usb_configuration, check whether the thread
is running before starting another one. Without that, when function
instance is added to multiple configurations, fsg_bing starts multiple
threads with all but the latest one being forgotten by the driver. This
leads to obvious thread leaks, possible lockups when trying to halt the
machine and possible more issues.
This fixes issues with legacy/multi¹ gadget as well as configfs gadgets
when mass_storage function is added to multiple configurations.
This change also simplifies API since the legacy gadgets no longer need
to worry about starting the thread by themselves (which was where bug
in legacy/multi was in the first place).
N.B., this patch doesn’t address adding single mass_storage function
instance to a single configuration twice. Thankfully, there’s no
legitimate reason for such setup plus, if I’m not mistaken, configfs
gadget doesn’t even allow it to be expressed.
¹ I have no example failure though. Conclusion that legacy/multi has
a bug is based purely on me reading the code.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Tested-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 332a5b446b upstream.
In the current implementation functionfs generates a EFAULT for async read
operations if the read buffer size is larger than the URB data size. Since
a application does not necessarily know how much data the host side is
going to send it typically supplies a buffer larger than the actual data,
which will then result in a EFAULT error.
This behaviour was introduced while refactoring the code to use iov_iter
interface in commit c993c39b86 ("gadget/function/f_fs.c: use put iov_iter
into io_data"). The original code took the minimum over the URB size and
the user buffer size and then attempted to copy that many bytes using
copy_to_user(). If copy_to_user() could not copy all data a EFAULT error
was generated. Restore the original behaviour by only generating a EFAULT
error when the number of bytes copied is not the size of the URB and the
target buffer has not been fully filled.
Commit 342f39a6c8 ("usb: gadget: f_fs: fix check in read operation")
already fixed the same problem for the synchronous read path.
Fixes: c993c39b86 ("gadget/function/f_fs.c: use put iov_iter into io_data")
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 444f94e9e6 upstream.
Added support for Gemalto's Cinterion PH8 and AHxx products
with 2 RmNet Interfaces and products with 1 RmNet + 1 USB Audio interface.
In addition some minor renaming and formatting.
Signed-off-by: Hans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com>
[johan: sort current entries and trim trailing whitespace ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c8d62957d4 upstream.
URBs and buffers allocated in attach for Epic devices would never be
deallocated in case of a later probe error (e.g. failure to allocate
minor numbers) as disconnect is then never called.
Fix by moving deallocation to release and making sure that the
URBs are first unlinked.
Fixes: f9c99bb8b3 ("USB: usb-serial: replace shutdown with disconnect,
release")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c5c0c55598 upstream.
Private data, URBs and buffers allocated for Epic devices during
attach were never released on errors (e.g. missing endpoints).
Fixes: 6e8cf7751f ("USB: add EPIC support to the io_edgeport driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 028c49f5e0 upstream.
The interface read URB is submitted in attach, but was only unlinked by
the driver at disconnect.
In case of a late probe error (e.g. due to failed minor allocation),
disconnect is never called and we would end up with active URBs for an
unbound interface. This in turn could lead to deallocated memory being
dereferenced in the completion callback.
Fixes: f7a33e608d ("USB: serial: add quatech2 usb to serial driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 35be1a71d7 upstream.
The interface instat and indat URBs were submitted in attach, but never
unlinked in release before deallocating the corresponding transfer
buffers.
In the case of a late probe error (e.g. due to failed minor allocation),
disconnect would not have been called before release, causing the
buffers to be freed while the URBs are still in use. We'd also end up
with active URBs for an unbound interface.
Fixes: f9c99bb8b3 ("USB: usb-serial: replace shutdown with disconnect,
release")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9e45284984 upstream.
The interface read and event URBs are submitted in attach, but were
never explicitly unlinked by the driver. Instead the URBs would have
been killed by usb-serial core on disconnect.
In case of a late probe error (e.g. due to failed minor allocation),
disconnect is never called and we could end up with active URBs for an
unbound interface. This in turn could lead to deallocated memory being
dereferenced in the completion callbacks.
Fixes: ee467a1f20 ("USB: serial: add Moxa UPORT 12XX/14XX/16XX
driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bc46b45a42 upstream.
Ensure that mei_cl_read_start is called under the device lock
also in the bus layer. The function updates global ctrl_wr_list
which should be locked.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9d04ee11db upstream.
When a message is received and amthif client is not in reading state
the message is ignored and left dangling in the queue. This may happen
after one of the amthif host connections is closed w/o completing the
reading. Another client will pick up a wrong message on next read
attempt which will lead to link reset.
To prevent this the driver has to properly discard the message when
amthif client is not in reading state.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6a8d648c8d upstream.
In the case when disconnection is initiated from the FW
the driver is flushing items from the write control list while
iterating over it:
mei_irq_write_handler()
list_for_each_entry_safe(ctrl_wr_list) <-- outer loop
mei_cl_irq_disconnect_rsp()
mei_cl_set_disconnected()
mei_io_list_flush(ctrl_wr_list) <-- destorying list
We move the list flushing to the completion routine.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c7c999cb18 upstream.
hci_vhci driver creates a hci device object dynamically upon each
HCI_VENDOR_PKT write. Although it checks the already created object
and returns an error, it's still racy and may build multiple hci_dev
objects concurrently when parallel writes are performed, as the device
tracks only a single hci_dev object.
This patch introduces a mutex to protect against the concurrent device
creations.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 373a32c848 upstream.
Both vhci_get_user and vhci_release race with open_timeout work. They
both contain cancel_delayed_work_sync, but do not test whether the
work actually created hdev or not. Since the work can be in progress
and _sync will wait for finishing it, we can have data->hdev allocated
when cancel_delayed_work_sync returns. But the call sites do 'if
(data->hdev)' *before* cancel_delayed_work_sync.
As a result:
* vhci_get_user allocates a second hdev and puts it into
data->hdev. The former is leaked.
* vhci_release does not release data->hdev properly as it thinks there
is none.
Fix both cases by moving the actual test *after* the call to
cancel_delayed_work_sync.
This can be hit by this program:
#include <err.h>
#include <fcntl.h>
#include <stdio.h>
#include <stdlib.h>
#include <time.h>
#include <unistd.h>
#include <sys/stat.h>
#include <sys/types.h>
int main(int argc, char **argv)
{
int fd;
srand(time(NULL));
while (1) {
const int delta = (rand() % 200 - 100) * 100;
fd = open("/dev/vhci", O_RDWR);
if (fd < 0)
err(1, "open");
usleep(1000000 + delta);
close(fd);
}
return 0;
}
And the result is:
BUG: KASAN: use-after-free in skb_queue_tail+0x13e/0x150 at addr ffff88006b0c1228
Read of size 8 by task kworker/u13:1/32068
=============================================================================
BUG kmalloc-192 (Tainted: G E ): kasan: bad access detected
-----------------------------------------------------------------------------
Disabling lock debugging due to kernel taint
INFO: Allocated in vhci_open+0x50/0x330 [hci_vhci] age=260 cpu=3 pid=32040
...
kmem_cache_alloc_trace+0x150/0x190
vhci_open+0x50/0x330 [hci_vhci]
misc_open+0x35b/0x4e0
chrdev_open+0x23b/0x510
...
INFO: Freed in vhci_release+0xa4/0xd0 [hci_vhci] age=9 cpu=2 pid=32040
...
__slab_free+0x204/0x310
vhci_release+0xa4/0xd0 [hci_vhci]
...
INFO: Slab 0xffffea0001ac3000 objects=16 used=13 fp=0xffff88006b0c1e00 flags=0x5fffff80004080
INFO: Object 0xffff88006b0c1200 @offset=4608 fp=0xffff88006b0c0600
Bytes b4 ffff88006b0c11f0: 09 df 00 00 01 00 00 00 00 00 00 00 00 00 00 00 ................
Object ffff88006b0c1200: 00 06 0c 6b 00 88 ff ff 00 00 00 00 00 00 00 00 ...k............
Object ffff88006b0c1210: 10 12 0c 6b 00 88 ff ff 10 12 0c 6b 00 88 ff ff ...k.......k....
Object ffff88006b0c1220: c0 46 c2 6b 00 88 ff ff c0 46 c2 6b 00 88 ff ff .F.k.....F.k....
Object ffff88006b0c1230: 01 00 00 00 01 00 00 00 e0 ff ff ff 0f 00 00 00 ................
Object ffff88006b0c1240: 40 12 0c 6b 00 88 ff ff 40 12 0c 6b 00 88 ff ff @..k....@..k....
Object ffff88006b0c1250: 50 0d 6e a0 ff ff ff ff 00 02 00 00 00 00 ad de P.n.............
Object ffff88006b0c1260: 00 00 00 00 00 00 00 00 ab 62 02 00 01 00 00 00 .........b......
Object ffff88006b0c1270: 90 b9 19 81 ff ff ff ff 38 12 0c 6b 00 88 ff ff ........8..k....
Object ffff88006b0c1280: 03 00 20 00 ff ff ff ff ff ff ff ff 00 00 00 00 .. .............
Object ffff88006b0c1290: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
Object ffff88006b0c12a0: 00 00 00 00 00 00 00 00 00 80 cd 3d 00 88 ff ff ...........=....
Object ffff88006b0c12b0: 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 . ..............
Redzone ffff88006b0c12c0: bb bb bb bb bb bb bb bb ........
Padding ffff88006b0c13f8: 00 00 00 00 00 00 00 00 ........
CPU: 3 PID: 32068 Comm: kworker/u13:1 Tainted: G B E 4.4.6-0-default #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.8.1-0-g4adadbd-20151112_172657-sheep25 04/01/2014
Workqueue: hci0 hci_cmd_work [bluetooth]
00000000ffffffff ffffffff81926cfa ffff88006be37c68 ffff88006bc27180
ffff88006b0c1200 ffff88006b0c1234 ffffffff81577993 ffffffff82489320
ffff88006bc24240 0000000000000046 ffff88006a100000 000000026e51eb80
Call Trace:
...
[<ffffffff81ec8ebe>] ? skb_queue_tail+0x13e/0x150
[<ffffffffa06e027c>] ? vhci_send_frame+0xac/0x100 [hci_vhci]
[<ffffffffa0c61268>] ? hci_send_frame+0x188/0x320 [bluetooth]
[<ffffffffa0c61515>] ? hci_cmd_work+0x115/0x310 [bluetooth]
[<ffffffff811a1375>] ? process_one_work+0x815/0x1340
[<ffffffff811a1f85>] ? worker_thread+0xe5/0x11f0
[<ffffffff811a1ea0>] ? process_one_work+0x1340/0x1340
[<ffffffff811b3c68>] ? kthread+0x1c8/0x230
...
Memory state around the buggy address:
ffff88006b0c1100: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff88006b0c1180: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff88006b0c1200: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff88006b0c1280: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
ffff88006b0c1300: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
Fixes: 23424c0d31 (Bluetooth: Add support creating virtual AMP controllers)
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 32ecd320db upstream.
008GE0 Toshiba mmc in some Intel Baytrail tablets responds to
MMC_SEND_EXT_CSD in 450-600ms.
This patch will...
() Increase the long read time quirk timeout from 300ms to 600ms. Original
author of that quirk says 300ms was only a guess and that the number
may need to be raised in the future.
() Add this specific MMC to the quirk
Signed-off-by: Matt Gumbel <matthew.k.gumbel@intel.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 30c9bb0d76 upstream.
The order of the _OSI related functionalities is as follows:
acpi_blacklisted()
acpi_dmi_osi_linux()
acpi_osi_setup()
acpi_osi_setup()
acpi_update_interfaces() if "!*"
<<<<<<<<<<<<<<<<<<<<<<<<
parse_args()
__setup("acpi_osi=")
acpi_osi_setup_linux()
acpi_update_interfaces() if "!*"
<<<<<<<<<<<<<<<<<<<<<<<<
acpi_early_init()
acpi_initialize_subsystem()
acpi_ut_initialize_interfaces()
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
acpi_bus_init()
acpi_os_initialize1()
acpi_install_interface_handler(acpi_osi_handler)
acpi_osi_setup_late()
acpi_update_interfaces() for "!"
>>>>>>>>>>>>>>>>>>>>>>>>
acpi_osi_handler()
Since acpi_osi_setup_linux() can override acpi_dmi_osi_linux(), the command
line setting can override the DMI detection. That's why acpi_blacklisted()
is put before __setup("acpi_osi=").
Then we can notice the following wrong invocation order. There are
acpi_update_interfaces() (marked by <<<<) calls invoked before
acpi_ut_initialize_interfaces() (marked by ^^^^). This makes it impossible
to use acpi_osi=!* correctly from OSI DMI table or from the command line.
The use of acpi_osi=!* is meant to disable both ACPICA
(acpi_gbl_supported_interfaces) and Linux specific strings
(osi_setup_entries) while the ACPICA part should have stopped working
because of the order issue.
This patch fixes this issue by moving acpi_update_interfaces() to where
it is invoked for acpi_osi=! (marked by >>>>) as this is ensured to be
invoked after acpi_ut_initialize_interfaces() (marked by ^^^^). Linux
specific strings are still handled in the original place in order to make
the following command line working: acpi_osi=!* acpi_osi="Module Device".
Note that since acpi_osi=!* is meant to further disable linux specific
string comparing to the acpi_osi=!, there is no such use case in our bug
fixing work and hence there is no one using acpi_osi=!* either from the
command line or from the DMI quirks, this issue is just a theoretical
issue.
Fixes: 741d81280a (ACPI: Add facility to remove all _OSI strings)
Tested-by: Lukas Wunner <lukas@wunner.de>
Tested-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c447116d0 upstream.
Some eMMCs set the partition switch timeout too low.
Now typically eMMCs are considered a critical component (e.g. because
they store the root file system) and consequently are expected to be
reliable. Thus we can neglect the use case where eMMCs can't switch
reliably and we might want a lower timeout to facilitate speedy
recovery.
Although we could employ a quirk for the cards that are affected (if
we could identify them all), as described above, there is little
benefit to having a low timeout, so instead simply set a minimum
timeout.
The minimum is set to 300ms somewhat arbitrarily - the examples that
have been seen had a timeout of 10ms but were sometimes taking 60-70ms.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb208f144c upstream.
As described in 'can: m_can: tag current CAN FD controllers as non-ISO'
(6cfda7fbeb) it is possible to define fixed configuration options by
setting the according bit in 'ctrlmode' and clear it in 'ctrlmode_supported'.
This leads to the incovenience that the fixed configuration bits can not be
passed by netlink even when they have the correct values (e.g. non-ISO, FD).
This patch fixes that issue and not only allows fixed set bit values to be set
again but now requires(!) to provide these fixed values at configuration time.
A valid CAN FD configuration consists of a nominal/arbitration bittiming, a
data bittiming and a control mode with CAN_CTRLMODE_FD set - which is now
enforced by a new can_validate() function. This fix additionally removed the
inconsistency that was prohibiting the support of 'CANFD-only' controller
drivers, like the RCar CAN FD.
For this reason a new helper can_set_static_ctrlmode() has been introduced to
provide a proper interface to handle static enabled CAN controller options.
Reported-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Reviewed-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b58afe6d6d upstream.
Fix static checker warning:
drivers/nfc/st21nfca/i2c.c:530 st21nfca_hci_i2c_acpi_request_resources()
error: 'gpiod_ena' dereferencing possible ERR_PTR()
Fix so that if no enable gpio can be retrieved an -ENODEV is returned.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: dfa8070d7f ("nfc: st21nfca: Add support for acpi probing for i2c device.")
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c9b973061 upstream.
The GICv3 driver wrongly assumes that it runs on the non-secure
side of a secure-enabled system, while it could be on a system
with a single security state, or a GICv3 with GICD_CTLR.DS set.
Either way, it is important to configure this properly, or
interrupts will simply not be delivered on this HW.
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f86c4fbd93 upstream.
When an IPI is generated by a CPU, the pattern looks roughly like:
<write shared data>
smp_wmb();
<write to GIC to signal SGI>
On the receiving CPU we rely on the fact that, once we've taken the
interrupt, then the freshly written shared data must be visible to us.
Put another way, the CPU isn't going to speculate taking an interrupt.
Unfortunately, this assumption turns out to be broken.
Consider that CPUx wants to send an IPI to CPUy, which will cause CPUy
to read some shared_data. Before CPUx has done anything, a random
peripheral raises an IRQ to the GIC and the IRQ line on CPUy is raised.
CPUy then takes the IRQ and starts executing the entry code, heading
towards gic_handle_irq. Furthermore, let's assume that a bunch of the
previous interrupts handled by CPUy were SGIs, so the branch predictor
kicks in and speculates that irqnr will be <16 and we're likely to
head into handle_IPI. The prefetcher then grabs a speculative copy of
shared_data which contains a stale value.
Meanwhile, CPUx gets round to updating shared_data and asking the GIC
to send an SGI to CPUy. Internally, the GIC decides that the SGI is
more important than the peripheral interrupt (which hasn't yet been
ACKed) but doesn't need to do anything to CPUy, because the IRQ line
is already raised.
CPUy then reads the ACK register on the GIC, sees the SGI value which
confirms the branch prediction and we end up with a stale shared_data
value.
This patch fixes the problem by adding an smp_rmb() to the IPI entry
code in gic_handle_irq. As it turns out, the combination of a control
dependency and an ISB instruction from the EOI in the GICv3 driver is
enough to provide the ordering we need, so we add a comment there
justifying the absence of an explicit smp_rmb().
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f49cf3b8b4 upstream.
Pwm config may sleep so defer it using a worker.
On a Freescale i.MX53 based board we ran into "BUG: scheduling while
atomic" because input_inject_event locks interrupts, but
imx_pwm_config_v2 sleeps.
Tested on Freescale i.MX53 SoC with 4.6.0.
Signed-off-by: Manfred Schlaegl <manfred.schlaegl@gmx.at>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 20878232c5 upstream.
Systems show a minimal load average of 0.00, 0.01, 0.05 even when they
have no load at all.
Uptime and /proc/loadavg on all systems with kernels released during the
last five years up until kernel version 4.6-rc5, show a 5- and 15-minute
minimum loadavg of 0.01 and 0.05 respectively. This should be 0.00 on
idle systems, but the way the kernel calculates this value prevents it
from getting lower than the mentioned values.
Likewise but not as obviously noticeable, a fully loaded system with no
processes waiting, shows a maximum 1/5/15 loadavg of 1.00, 0.99, 0.95
(multiplied by number of cores).
Once the (old) load becomes 93 or higher, it mathematically can never
get lower than 93, even when the active (load) remains 0 forever.
This results in the strange 0.00, 0.01, 0.05 uptime values on idle
systems. Note: 93/2048 = 0.0454..., which rounds up to 0.05.
It is not correct to add a 0.5 rounding (=1024/2048) here, since the
result from this function is fed back into the next iteration again,
so the result of that +0.5 rounding value then gets multiplied by
(2048-2037), and then rounded again, so there is a virtual "ghost"
load created, next to the old and active load terms.
By changing the way the internally kept value is rounded, that internal
value equivalent now can reach 0.00 on idle, and 1.00 on full load. Upon
increasing load, the internally kept load value is rounded up, when the
load is decreasing, the load value is rounded down.
The modified code was tested on nohz=off and nohz kernels. It was tested
on vanilla kernel 4.6-rc5 and on centos 7.1 kernel 3.10.0-327. It was
tested on single, dual, and octal cores system. It was tested on virtual
hosts and bare hardware. No unwanted effects have been observed, and the
problems that the patch intended to fix were indeed gone.
Tested-by: Damien Wyart <damien.wyart@free.fr>
Signed-off-by: Vik Heyndrickx <vik.heyndrickx@veribox.net>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Doug Smythies <dsmythies@telus.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 0f004f5a69 ("sched: Cure more NO_HZ load average woes")
Link: http://lkml.kernel.org/r/e8d32bff-d544-7748-72b5-3c86cc71f09f@veribox.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a0974aa1a upstream.
This patch adds the CLK_SET_RATE_PARENT flag for the crypto core and
ahb blocks. Without this flag, clk_set_rate can fail for certain
frequency requests.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Fixes: 3966fab8b6 ("clk: qcom: Add MSM8916 Global Clock Controller support")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bdb6cf9f6f upstream.
The current sun4i-ss driver could generate data corruption when ciphering/deciphering.
It occurs randomly on end of handled data.
No root cause have been found and the only way to remove it is to replace
all spin_lock_bh by their irq counterparts.
Fixes: 6298e94821 ("crypto: sunxi-ss - Add Allwinner Security System crypto accelerator")
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e930c765ca upstream.
caam_jr_alloc() used to return NULL if a JR device could not be
allocated for a session. In turn, every user of this function used
IS_ERR() function to verify if anything went wrong, which does NOT look
for NULL values. This made the kernel crash if the sanity check failed,
because the driver continued to think it had allocated a valid JR dev
instance to the session and at some point it tries to do a caam_jr_free()
on a NULL JR dev pointer.
This patch is a fix for this issue.
Signed-off-by: Catalin Vasile <cata.vasile@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 59643d1535 upstream.
If the size passed to ring_buffer_resize() is greater than MAX_LONG - BUF_PAGE_SIZE
then the DIV_ROUND_UP() will return zero.
Here's the details:
# echo 18014398509481980 > /sys/kernel/debug/tracing/buffer_size_kb
tracing_entries_write() processes this and converts kb to bytes.
18014398509481980 << 10 = 18446744073709547520
and this is passed to ring_buffer_resize() as unsigned long size.
size = DIV_ROUND_UP(size, BUF_PAGE_SIZE);
Where DIV_ROUND_UP(a, b) is (a + b - 1)/b
BUF_PAGE_SIZE is 4080 and here
18446744073709547520 + 4080 - 1 = 18446744073709551599
where 18446744073709551599 is still smaller than 2^64
2^64 - 18446744073709551599 = 17
But now 18446744073709551599 / 4080 = 4521260802379792
and size = size * 4080 = 18446744073709551360
This is checked to make sure its still greater than 2 * 4080,
which it is.
Then we convert to the number of buffer pages needed.
nr_page = DIV_ROUND_UP(size, BUF_PAGE_SIZE)
but this time size is 18446744073709551360 and
2^64 - (18446744073709551360 + 4080 - 1) = -3823
Thus it overflows and the resulting number is less than 4080, which makes
3823 / 4080 = 0
an nr_pages is set to this. As we already checked against the minimum that
nr_pages may be, this causes the logic to fail as well, and we crash the
kernel.
There's no reason to have the two DIV_ROUND_UP() (that's just result of
historical code changes), clean up the code and fix this bug.
Fixes: 83f40318da ("ring-buffer: Make removal of ring buffer pages atomic")
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b94a8fba5 upstream.
The size variable to change the ring buffer in ftrace is a long. The
nr_pages used to update the ring buffer based on the size is int. On 64 bit
machines this can cause an overflow problem.
For example, the following will cause the ring buffer to crash:
# cd /sys/kernel/debug/tracing
# echo 10 > buffer_size_kb
# echo 8556384240 > buffer_size_kb
Then you get the warning of:
WARNING: CPU: 1 PID: 318 at kernel/trace/ring_buffer.c:1527 rb_update_pages+0x22f/0x260
Which is:
RB_WARN_ON(cpu_buffer, nr_removed);
Note each ring buffer page holds 4080 bytes.
This is because:
1) 10 causes the ring buffer to have 3 pages.
(10kb requires 3 * 4080 pages to hold)
2) (2^31 / 2^10 + 1) * 4080 = 8556384240
The value written into buffer_size_kb is shifted by 10 and then passed
to ring_buffer_resize(). 8556384240 * 2^10 = 8761737461760
3) The size passed to ring_buffer_resize() is then divided by BUF_PAGE_SIZE
which is 4080. 8761737461760 / 4080 = 2147484672
4) nr_pages is subtracted from the current nr_pages (3) and we get:
2147484669. This value is saved in a signed integer nr_pages_to_update
5) 2147484669 is greater than 2^31 but smaller than 2^32, a signed int
turns into the value of -2147482627
6) As the value is a negative number, in update_pages_handler() it is
negated and passed to rb_remove_pages() and 2147482627 pages will
be removed, which is much larger than 3 and it causes the warning
because not all the pages asked to be removed were removed.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=118001
Fixes: 7a8e76a382 ("tracing: unified trace buffer")
Reported-by: Hao Qin <QEver.cn@gmail.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd9e2e5d3f upstream.
In testing with HiKey, we found that since
commit 3f30b158eb ("asix: On RX avoid creating bad Ethernet
frames"),
we're seeing lots of noise during network transfers:
[ 239.027993] asix 1-1.1:1.0 eth0: asix_rx_fixup() Data Header synchronisation was lost, remaining 988
[ 239.037310] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0x54ebb5ec, offset 4
[ 239.045519] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0xcdffe7a2, offset 4
[ 239.275044] asix 1-1.1:1.0 eth0: asix_rx_fixup() Data Header synchronisation was lost, remaining 988
[ 239.284355] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0x1d36f59d, offset 4
[ 239.292541] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0xaef3c1e9, offset 4
[ 239.518996] asix 1-1.1:1.0 eth0: asix_rx_fixup() Data Header synchronisation was lost, remaining 988
[ 239.528300] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0x2881912, offset 4
[ 239.536413] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0x5638f7e2, offset 4
And network throughput ends up being pretty bursty and slow with
a overall throughput of at best ~30kB/s (where as previously we
got 1.1MB/s with the slower USB1.1 "full speed" host).
We found the issue also was reproducible on a x86_64 system,
using a "high-speed" USB2.0 port but the throughput did not
measurably drop (possibly due to the scp transfer being cpu
bound on my slow test hardware).
After lots of debugging, I found the check added in the
problematic commit seems to be calculating the offset
incorrectly.
In the normal case, in the main loop of the function, we do:
(where offset is zero, or set to "offset += (copy_length + 1) &
0xfffe" in the previous loop)
rx->header = get_unaligned_le32(skb->data +
offset);
offset += sizeof(u32);
But the problematic patch calculates:
offset = ((rx->remaining + 1) & 0xfffe) + sizeof(u32);
rx->header = get_unaligned_le32(skb->data + offset);
Adding some debug logic to check those offset calculation used
to find rx->header, the one in problematic code is always too
large by sizeof(u32).
Thus, this patch removes the incorrect " + sizeof(u32)" addition
in the problematic calculation, and resolves the issue.
Cc: Dean Jenkins <Dean_Jenkins@mentor.com>
Cc: "David B. Robins" <linux@davidrobins.net>
Cc: Mark Craske <Mark_Craske@mentor.com>
Cc: Emil Goode <emilgoode@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: YongQin Liu <yongqin.liu@linaro.org>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Ivan Vecera <ivecera@redhat.com>
Cc: linux-usb@vger.kernel.org
Cc: netdev@vger.kernel.org
Reported-by: Yongqin Liu <yongqin.liu@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cfda35d982 upstream.
See [MS-NLMP] 3.2.5.1.2 Server Receives an AUTHENTICATE_MESSAGE from the Client:
...
Set NullSession to FALSE
If (AUTHENTICATE_MESSAGE.UserNameLen == 0 AND
AUTHENTICATE_MESSAGE.NtChallengeResponse.Length == 0 AND
(AUTHENTICATE_MESSAGE.LmChallengeResponse == Z(1)
OR
AUTHENTICATE_MESSAGE.LmChallengeResponse.Length == 0))
-- Special case: client requested anonymous authentication
Set NullSession to TRUE
...
Only server which map unknown users to guest will allow
access using a non-null NTChallengeResponse.
For Samba it's the "map to guest = bad user" option.
BUG: https://bugzilla.samba.org/show_bug.cgi?id=11913
Signed-off-by: Stefan Metzmacher <metze@samba.org>
Signed-off-by: Steve French <smfrench@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 897fba1172 upstream.
Wrong return code was being returned on SMB3 rmdir of
non-empty directory.
For SMB3 (unlike for cifs), we attempt to delete a directory by
set of delete on close flag on the open. Windows clients set
this flag via a set info (SET_FILE_DISPOSITION to set this flag)
which properly checks if the directory is empty.
With this patch on smb3 mounts we correctly return
"DIRECTORY NOT EMPTY"
on attempts to remove a non-empty directory.
Signed-off-by: Steve French <steve.french@primarydata.com>
Acked-by: Sachin Prabhu <sprabhu@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e4fe9e7dc3 upstream.
The EC field of the constructed ESR is conditionally modified by ORing in
ESR_ELx_EC_DABT_LOW for a data abort. However, ESR_ELx_EC_SHIFT is missing
from this condition.
Signed-off-by: Matt Evans <matt.evans@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d4b9e0790a upstream.
The ARM architecture mandates that when changing a page table entry
from a valid entry to another valid entry, an invalid entry is first
written, TLB invalidated, and only then the new entry being written.
The current code doesn't respect this, directly writing the new
entry and only then invalidating TLBs. Let's fix it up.
Reported-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f228b494e5 upstream.
The loop that browses the array compat_hwcap_str will stop when a NULL
is encountered, however NULL is missing at the end of array. This will
lead to overrun until a NULL is found somewhere in the following memory.
In reality, this works out because the compat_hwcap2_str array tends to
follow immediately in memory, and that *is* terminated correctly.
Furthermore, the unsigned int compat_elf_hwcap is checked before
printing each capability, so we end up doing the right thing because
the size of the two arrays is less than 32. Still, this is an obvious
mistake and should be fixed.
Note for backporting: commit 12d11817ea ("arm64: Move
/proc/cpuinfo handling code") moved this code in v4.4. Prior to that
commit, the same change should be made in arch/arm64/kernel/setup.c.
Fixes: 44b82b7700 "arm64: Fix up /proc/cpuinfo"
Signed-off-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 282aa7051b upstream.
The update to the accessed or dirty states for block mappings must be
done atomically on hardware with support for automatic AF/DBM. The
ptep_set_access_flags() function has been fixed as part of commit
66dbd6e61a ("arm64: Implement ptep_set_access_flags() for hardware
AF/DBM"). This patch brings pmdp_set_access_flags() in line with the pte
counterpart.
Fixes: 2f4b829c62 ("arm64: Add support for hardware updates of the access and dirty pte bits")
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66dbd6e61a upstream.
When hardware updates of the access and dirty states are enabled, the
default ptep_set_access_flags() implementation based on calling
set_pte_at() directly is potentially racy. This triggers the "racy dirty
state clearing" warning in set_pte_at() because an existing writable PTE
is overridden with a clean entry.
There are two main scenarios for this situation:
1. The CPU getting an access fault does not support hardware updates of
the access/dirty flags. However, a different agent in the system
(e.g. SMMU) can do this, therefore overriding a writable entry with a
clean one could potentially lose the automatically updated dirty
status
2. A more complex situation is possible when all CPUs support hardware
AF/DBM:
a) Initial state: shareable + writable vma and pte_none(pte)
b) Read fault taken by two threads of the same process on different
CPUs
c) CPU0 takes the mmap_sem and proceeds to handling the fault. It
eventually reaches do_set_pte() which sets a writable + clean pte.
CPU0 releases the mmap_sem
d) CPU1 acquires the mmap_sem and proceeds to handle_pte_fault(). The
pte entry it reads is present, writable and clean and it continues
to pte_mkyoung()
e) CPU1 calls ptep_set_access_flags()
If between (d) and (e) the hardware (another CPU) updates the dirty
state (clears PTE_RDONLY), CPU1 will override the PTR_RDONLY bit
marking the entry clean again.
This patch implements an arm64-specific ptep_set_access_flags() function
to perform an atomic update of the PTE flags.
Fixes: 2f4b829c62 ("arm64: Add support for hardware updates of the access and dirty pte bits")
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Ming Lei <tom.leiming@gmail.com>
Tested-by: Julien Grall <julien.grall@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
[will: reworded comment]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5bb1cc0ff9 upstream.
Currently, pmd_present() only checks for a non-zero value, returning
true even after pmd_mknotpresent() (which only clears the type bits).
This patch converts pmd_present() to using pte_present(), similar to the
other pmd_*() checks. As a side effect, it will return true for
PROT_NONE mappings, though they are not yet used by the kernel with
transparent huge pages.
For consistency, also change pmd_mknotpresent() to only clear the
PMD_SECT_VALID bit, even though the PMD_TABLE_BIT is already 0 for block
mappings (no functional change). The unused PMD_SECT_PROT_NONE
definition is removed as transparent huge pages use the pte page prot
values.
Fixes: 9c7e535fcc ("arm64: mm: Route pmd thp functions through pte equivalents")
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 911f56eeb8 upstream.
With hardware AF/DBM support, pmd modifications (transparent huge pages)
should be performed atomically using load/store exclusive. The initial
patches defined the get-and-clear function and __HAVE_ARCH_* macro
without the "huge" word, leaving the pmdp_huge_get_and_clear() to the
default, non-atomic implementation.
Fixes: 2f4b829c62 ("arm64: Add support for hardware updates of the access and dirty pte bits")
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 79c9ce57eb upstream.
Jann reported that the ptrace_may_access() check in
find_lively_task_by_vpid() is racy against exec().
Specifically:
perf_event_open() execve()
ptrace_may_access()
commit_creds()
... if (get_dumpable() != SUID_DUMP_USER)
perf_event_exit_task();
perf_install_in_context()
would result in installing a counter across the creds boundary.
Fix this by wrapping lots of perf_event_open() in cred_guard_mutex.
This should be fine as perf_event_exit_task() is already called with
cred_guard_mutex held, so all perf locks already nest inside it.
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: He Kuang <hekuang@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ab92b232ae upstream.
Currently, the PT driver always sets the PMI bit one region (page) before
the STOP region so that we can wake up the consumer before we run out of
room in the buffer and have to disable the event. However, we also need
an interrupt in the last output region, so that we actually get to disable
the event (if no more room from new data is available at that point),
otherwise hardware just quietly refuses to start, but the event is
scheduled in and we end up losing trace data till the event gets removed.
For a cpu-wide event it is even worse since there may not be any
re-scheduling at all and no chance for the ring buffer code to notice
that its buffer is filled up and the event needs to be disabled (so that
the consumer can re-enable it when it finishes reading the data out). In
other words, all the trace data will be lost after the buffer gets filled
up.
This patch makes PT also generate a PMI when the last output region is
full.
Reported-by: Markus Metzger <markus.t.metzger@intel.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: vince@deater.net
Link: http://lkml.kernel.org/r/1462886313-13660-2-git-send-email-alexander.shishkin@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 31b0b385f6 upstream.
The slab name ends up being visible in the directory structure under
/sys, and even if you don't have access rights to the file you can see
the filenames.
Just use a 64-bit counter instead of the pointer to the 'net' structure
to generate a unique name.
This code will go away in 4.7 when the conntrack code moves to a single
kmemcache, but this is the backportable simple solution to avoiding
leaking kernel pointers to user space.
Fixes: 5b3501faa8 ("netfilter: nf_conntrack: per netns nf_conntrack_cachep")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ccefb98ce upstream.
If device replace entry was found on disk at mounting and its num_write_errors
stats counter has non-NULL value, then replace operation will never be
finished and -EIO error will be reported by btrfs_scrub_dev() because
this counter is never reset.
# mount -o degraded /media/a4fb5c0a-21c5-4fe7-8d0e-fdd87d5f71ee/
# btrfs replace status /media/a4fb5c0a-21c5-4fe7-8d0e-fdd87d5f71ee/
Started on 25.Mar 07:28:00, canceled on 25.Mar 07:28:01 at 0.0%, 40 write errs, 0 uncorr. read errs
# btrfs replace start -B 4 /dev/sdg /media/a4fb5c0a-21c5-4fe7-8d0e-fdd87d5f71ee/
ERROR: ioctl(DEV_REPLACE_START) failed on "/media/a4fb5c0a-21c5-4fe7-8d0e-fdd87d5f71ee/": Input/output error, no error
Reset num_write_errors and num_uncorrectable_read_errors counters in the
dev_replace structure before start of replacing.
Signed-off-by: Yauhen Kharuzhy <yauhen.kharuzhy@zavadatar.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 918c2ee103 upstream.
create_pending_snapshot() will go readonly on _any_ error return from
btrfs_qgroup_inherit(). If qgroups are enabled, a user can crash their fs by
just making a snapshot and asking it to inherit from an invalid qgroup. For
example:
$ btrfs sub snap -i 1/10 /btrfs/ /btrfs/foo
Will cause a transaction abort.
Fix this by only throwing errors in btrfs_qgroup_inherit() when we know
going readonly is acceptable.
The following xfstests test case reproduces this bug:
seq=`basename $0`
seqres=$RESULT_DIR/$seq
echo "QA output created by $seq"
here=`pwd`
tmp=/tmp/$$
status=1 # failure is the default!
trap "_cleanup; exit \$status" 0 1 2 3 15
_cleanup()
{
cd /
rm -f $tmp.*
}
# get standard environment, filters and checks
. ./common/rc
. ./common/filter
# remove previous $seqres.full before test
rm -f $seqres.full
# real QA test starts here
_supported_fs btrfs
_supported_os Linux
_require_scratch
rm -f $seqres.full
_scratch_mkfs
_scratch_mount
_run_btrfs_util_prog quota enable $SCRATCH_MNT
# The qgroup '1/10' does not exist and should be silently ignored
_run_btrfs_util_prog subvolume snapshot -i 1/10 $SCRATCH_MNT $SCRATCH_MNT/snap1
_scratch_unmount
echo "Silence is golden"
status=0
exit
Signed-off-by: Mark Fasheh <mfasheh@suse.de>
Reviewed-by: Qu Wenruo <quwenruo@cn.fujitsu.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f805531da upstream.
csum_dirty_buffer was issuing a warning in case the extent buffer
did not look alright, but was still returning success.
Let's return error in this case, and also add an additional sanity
check on the extent buffer header.
The caller up the chain may BUG_ON on this, for example flush_epd_write_bio will,
but it is better than to have a silent metadata corruption on disk.
Signed-off-by: Alex Lyakas <alex@zadarastorage.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e33a2bd7c upstream.
When logging that an inode exists, for example as part of a directory
fsync operation, we were collecting any ordered extents for the inode but
we ended up doing nothing with them except tagging them as processed, by
setting the flag BTRFS_ORDERED_LOGGED on them, which prevented a
subsequent fsync of that inode (using the LOG_INODE_ALL mode) from
collecting and processing them. This created a time window where a second
fsync against the inode, using the fast path, ended up not logging the
checksums for the new extents but it logged the extents since they were
part of the list of modified extents. This happened because the ordered
extents were not collected and checksums were not yet added to the csum
tree - the ordered extents have not gone through btrfs_finish_ordered_io()
yet (which is where we add them to the csum tree by calling
inode.c:add_pending_csums()).
So fix this by not collecting an inode's ordered extents if we are logging
it with the LOG_INODE_EXISTS mode.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit affc0ff902 upstream.
If we're about to do a fast fsync for an inode and btrfs_inode_in_log()
returns false, it's possible that we had an ordered extent in progress
(btrfs_finish_ordered_io() not run yet) when we noticed that the inode's
last_trans field was not greater than the id of the last committed
transaction, but shortly after, before we checked if there were any
ongoing ordered extents, the ordered extent had just completed and
removed itself from the inode's ordered tree, in which case we end up not
logging the inode, losing some data if a power failure or crash happens
after the fsync handler returns and before the transaction is committed.
Fix this by checking first if there are any ongoing ordered extents
before comparing the inode's last_trans with the id of the last committed
transaction - when it completes, an ordered extent always updates the
inode's last_trans before it removes itself from the inode's ordered
tree (at btrfs_finish_ordered_io()).
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f4dfe68710 upstream.
When using the same file as the source and destination for a dedup
(extent_same ioctl) operation we were allowing it to dedup to a
destination offset beyond the file's size, which doesn't make sense and
it's not allowed for the case where the source and destination files are
not the same file. This made de deduplication operation successful only
when the source range corresponded to a hole, a prealloc extent or an
extent with all bytes having a value of 0x00. This was also leaving a
file hole (between i_size and destination offset) without the
corresponding file extent items, which can be reproduced with the
following steps for example:
$ mkfs.btrfs -f /dev/sdi
$ mount /dev/sdi /mnt/sdi
$ xfs_io -f -c "pwrite -S 0xab 304457 404990" /mnt/sdi/foobar
wrote 404990/404990 bytes at offset 304457
395 KiB, 99 ops; 0.0000 sec (31.150 MiB/sec and 7984.5149 ops/sec)
$ /git/hub/duperemove/btrfs-extent-same 24576 /mnt/sdi/foobar 28672 /mnt/sdi/foobar 929792
Deduping 2 total files
(28672, 24576): /mnt/sdi/foobar
(929792, 24576): /mnt/sdi/foobar
1 files asked to be deduped
i: 0, status: 0, bytes_deduped: 24576
24576 total bytes deduped in this operation
$ umount /mnt/sdi
$ btrfsck /dev/sdi
Checking filesystem on /dev/sdi
UUID: 98c528aa-0833-427d-9403-b98032ffbf9d
checking extents
checking free space cache
checking fs roots
root 5 inode 257 errors 100, file extent discount
Found file extent holes:
start: 712704, len: 217088
found 540673 bytes used err is 1
total csum bytes: 400
total tree bytes: 131072
total fs tree bytes: 32768
total extent tree bytes: 16384
btree space waste bytes: 123675
file data blocks allocated: 671744
referenced 671744
btrfs-progs v4.2.3
So fix this by not allowing the destination to go beyond the file's size,
just as we do for the same where the source and destination files are not
the same.
A test for xfstests follows.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2be63d5ce9 upstream.
We have two cases where we end up deleting a file at log replay time
when we should not. For this to happen the file must have been renamed
and a directory inode must have been fsynced/logged.
Two examples that exercise these two cases are listed below.
Case 1)
$ mkfs.btrfs -f /dev/sdb
$ mount /dev/sdb /mnt
$ mkdir -p /mnt/a/b
$ mkdir /mnt/c
$ touch /mnt/a/b/foo
$ sync
$ mv /mnt/a/b/foo /mnt/c/
# Create file bar just to make sure the fsync on directory a/ does
# something and it's not a no-op.
$ touch /mnt/a/bar
$ xfs_io -c "fsync" /mnt/a
< power fail / crash >
The next time the filesystem is mounted, the log replay procedure
deletes file foo.
Case 2)
$ mkfs.btrfs -f /dev/sdb
$ mount /dev/sdb /mnt
$ mkdir /mnt/a
$ mkdir /mnt/b
$ mkdir /mnt/c
$ touch /mnt/a/foo
$ ln /mnt/a/foo /mnt/b/foo_link
$ touch /mnt/b/bar
$ sync
$ unlink /mnt/b/foo_link
$ mv /mnt/b/bar /mnt/c/
$ xfs_io -c "fsync" /mnt/a/foo
< power fail / crash >
The next time the filesystem is mounted, the log replay procedure
deletes file bar.
The reason why the files are deleted is because when we log inodes
other then the fsync target inode, we ignore their last_unlink_trans
value and leave the log without enough information to later replay the
rename operations. So we need to look at the last_unlink_trans values
and fallback to a transaction commit if they are greater than the
id of the last committed transaction.
So fix this by looking at the last_unlink_trans values and fallback to
transaction commits when needed. Also, when logging other inodes (for
case 1 we logged descendants of the fsync target inode while for case 2
we logged ascendants) we need to care about concurrent tasks updating
the last_unlink_trans of inodes we are logging (which was already an
existing problem in check_parent_dirs_for_sync()). Since we can not
acquire their inode mutex (vfs' struct inode ->i_mutex), as that causes
deadlocks with other concurrent operations that acquire the i_mutex of
2 inodes (other fsyncs or renames for example), we need to serialize on
the log_mutex of the inode we are logging. A task setting a new value for
an inode's last_unlink_trans must acquire the inode's log_mutex and it
must do this update before doing the actual unlink operation (which is
already the case except when deleting a snapshot). Conversely the task
logging the inode must first log the inode and then check the inode's
last_unlink_trans value while holding its log_mutex, as if its value is
not greater then the id of the last committed transaction it means it
logged a safe state of the inode's items, while if its value is not
smaller then the id of the last committed transaction it means the inode
state it has logged might not be safe (the concurrent task might have
just updated last_unlink_trans but hasn't done yet the unlink operation)
and therefore a transaction commit must be done.
Test cases for xfstests follow in separate patches.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ec9a1ae1e upstream.
If we delete a snapshot, fsync its parent directory and crash/power fail
before the next transaction commit, on the next mount when we attempt to
replay the log tree of the root containing the parent directory we will
fail and prevent the filesystem from mounting, which is solvable by wiping
out the log trees with the btrfs-zero-log tool but very inconvenient as
we will lose any data and metadata fsynced before the parent directory
was fsynced.
For example:
$ mkfs.btrfs -f /dev/sdc
$ mount /dev/sdc /mnt
$ mkdir /mnt/testdir
$ btrfs subvolume snapshot /mnt /mnt/testdir/snap
$ btrfs subvolume delete /mnt/testdir/snap
$ xfs_io -c "fsync" /mnt/testdir
< crash / power failure and reboot >
$ mount /dev/sdc /mnt
mount: mount(2) failed: No such file or directory
And in dmesg/syslog we get the following message and trace:
[192066.361162] BTRFS info (device dm-0): failed to delete reference to snap, inode 257 parent 257
[192066.363010] ------------[ cut here ]------------
[192066.365268] WARNING: CPU: 4 PID: 5130 at fs/btrfs/inode.c:3986 __btrfs_unlink_inode+0x17a/0x354 [btrfs]()
[192066.367250] BTRFS: Transaction aborted (error -2)
[192066.368401] Modules linked in: btrfs dm_flakey dm_mod ppdev sha256_generic xor raid6_pq hmac drbg ansi_cprng aesni_intel acpi_cpufreq tpm_tis aes_x86_64 tpm ablk_helper evdev cryptd sg parport_pc i2c_piix4 psmouse lrw parport i2c_core pcspkr gf128mul processor serio_raw glue_helper button loop autofs4 ext4 crc16 mbcache jbd2 sd_mod sr_mod cdrom ata_generic virtio_scsi ata_piix libata virtio_pci virtio_ring crc32c_intel scsi_mod e1000 virtio floppy [last unloaded: btrfs]
[192066.377154] CPU: 4 PID: 5130 Comm: mount Tainted: G W 4.4.0-rc6-btrfs-next-20+ #1
[192066.378875] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS by qemu-project.org 04/01/2014
[192066.380889] 0000000000000000 ffff880143923670 ffffffff81257570 ffff8801439236b8
[192066.382561] ffff8801439236a8 ffffffff8104ec07 ffffffffa039dc2c 00000000fffffffe
[192066.384191] ffff8801ed31d000 ffff8801b9fc9c88 ffff8801086875e0 ffff880143923710
[192066.385827] Call Trace:
[192066.386373] [<ffffffff81257570>] dump_stack+0x4e/0x79
[192066.387387] [<ffffffff8104ec07>] warn_slowpath_common+0x99/0xb2
[192066.388429] [<ffffffffa039dc2c>] ? __btrfs_unlink_inode+0x17a/0x354 [btrfs]
[192066.389236] [<ffffffff8104ec68>] warn_slowpath_fmt+0x48/0x50
[192066.389884] [<ffffffffa039dc2c>] __btrfs_unlink_inode+0x17a/0x354 [btrfs]
[192066.390621] [<ffffffff81184b55>] ? iput+0xb0/0x266
[192066.391200] [<ffffffffa039ea25>] btrfs_unlink_inode+0x1c/0x3d [btrfs]
[192066.391930] [<ffffffffa03ca623>] check_item_in_log+0x1fe/0x29b [btrfs]
[192066.392715] [<ffffffffa03ca827>] replay_dir_deletes+0x167/0x1cf [btrfs]
[192066.393510] [<ffffffffa03cccc7>] replay_one_buffer+0x417/0x570 [btrfs]
[192066.394241] [<ffffffffa03ca164>] walk_up_log_tree+0x10e/0x1dc [btrfs]
[192066.394958] [<ffffffffa03cac72>] walk_log_tree+0xa5/0x190 [btrfs]
[192066.395628] [<ffffffffa03ce8b8>] btrfs_recover_log_trees+0x239/0x32c [btrfs]
[192066.396790] [<ffffffffa03cc8b0>] ? replay_one_extent+0x50a/0x50a [btrfs]
[192066.397891] [<ffffffffa0394041>] open_ctree+0x1d8b/0x2167 [btrfs]
[192066.398897] [<ffffffffa03706e1>] btrfs_mount+0x5ef/0x729 [btrfs]
[192066.399823] [<ffffffff8108ad98>] ? trace_hardirqs_on+0xd/0xf
[192066.400739] [<ffffffff8108959b>] ? lockdep_init_map+0xb9/0x1b3
[192066.401700] [<ffffffff811714b9>] mount_fs+0x67/0x131
[192066.402482] [<ffffffff81188560>] vfs_kern_mount+0x6c/0xde
[192066.403930] [<ffffffffa03702bd>] btrfs_mount+0x1cb/0x729 [btrfs]
[192066.404831] [<ffffffff8108ad98>] ? trace_hardirqs_on+0xd/0xf
[192066.405726] [<ffffffff8108959b>] ? lockdep_init_map+0xb9/0x1b3
[192066.406621] [<ffffffff811714b9>] mount_fs+0x67/0x131
[192066.407401] [<ffffffff81188560>] vfs_kern_mount+0x6c/0xde
[192066.408247] [<ffffffff8118ae36>] do_mount+0x893/0x9d2
[192066.409047] [<ffffffff8113009b>] ? strndup_user+0x3f/0x8c
[192066.409842] [<ffffffff8118b187>] SyS_mount+0x75/0xa1
[192066.410621] [<ffffffff8147e517>] entry_SYSCALL_64_fastpath+0x12/0x6b
[192066.411572] ---[ end trace 2de42126c1e0a0f0 ]---
[192066.412344] BTRFS: error (device dm-0) in __btrfs_unlink_inode:3986: errno=-2 No such entry
[192066.413748] BTRFS: error (device dm-0) in btrfs_replay_log:2464: errno=-2 No such entry (Failed to recover log tree)
[192066.415458] BTRFS error (device dm-0): cleaner transaction attach returned -30
[192066.444613] BTRFS: open_ctree failed
This happens because when we are replaying the log and processing the
directory entry pointing to the snapshot in the subvolume tree, we treat
its btrfs_dir_item item as having a location with a key type matching
BTRFS_INODE_ITEM_KEY, which is wrong because the type matches
BTRFS_ROOT_ITEM_KEY and therefore must be processed differently, as the
object id refers to a root number and not to an inode in the root
containing the parent directory.
So fix this by triggering a transaction commit if an fsync against the
parent directory is requested after deleting a snapshot. This is the
simplest approach for a rare use case. Some alternative that avoids the
transaction commit would require more code to explicitly delete the
snapshot at log replay time (factoring out common code from ioctl.c:
btrfs_ioctl_snap_destroy()), special care at fsync time to remove the
log tree of the snapshot's root from the log root of the root of tree
roots, amongst other steps.
A test case for xfstests that triggers the issue follows.
seq=`basename $0`
seqres=$RESULT_DIR/$seq
echo "QA output created by $seq"
tmp=/tmp/$$
status=1 # failure is the default!
trap "_cleanup; exit \$status" 0 1 2 3 15
_cleanup()
{
_cleanup_flakey
cd /
rm -f $tmp.*
}
# get standard environment, filters and checks
. ./common/rc
. ./common/filter
. ./common/dmflakey
# real QA test starts here
_need_to_be_root
_supported_fs btrfs
_supported_os Linux
_require_scratch
_require_dm_target flakey
_require_metadata_journaling $SCRATCH_DEV
rm -f $seqres.full
_scratch_mkfs >>$seqres.full 2>&1
_init_flakey
_mount_flakey
# Create a snapshot at the root of our filesystem (mount point path), delete it,
# fsync the mount point path, crash and mount to replay the log. This should
# succeed and after the filesystem is mounted the snapshot should not be visible
# anymore.
_run_btrfs_util_prog subvolume snapshot $SCRATCH_MNT $SCRATCH_MNT/snap1
_run_btrfs_util_prog subvolume delete $SCRATCH_MNT/snap1
$XFS_IO_PROG -c "fsync" $SCRATCH_MNT
_flakey_drop_and_remount
[ -e $SCRATCH_MNT/snap1 ] && \
echo "Snapshot snap1 still exists after log replay"
# Similar scenario as above, but this time the snapshot is created inside a
# directory and not directly under the root (mount point path).
mkdir $SCRATCH_MNT/testdir
_run_btrfs_util_prog subvolume snapshot $SCRATCH_MNT $SCRATCH_MNT/testdir/snap2
_run_btrfs_util_prog subvolume delete $SCRATCH_MNT/testdir/snap2
$XFS_IO_PROG -c "fsync" $SCRATCH_MNT/testdir
_flakey_drop_and_remount
[ -e $SCRATCH_MNT/testdir/snap2 ] && \
echo "Snapshot snap2 still exists after log replay"
_unmount_flakey
echo "Silence is golden"
status=0
exit
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Tested-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f7e98a7fff upstream.
The current practical default is ~4k on x86_64 (the logic is more complex,
simplified for brevity), the inlined files land in the metadata group and
thus consume space that could be needed for the real metadata.
The inlining brings some usability surprises:
1) total space consumption measured on various filesystems and btrfs
with DUP metadata was quite visible because of the duplicated data
within metadata
2) inlined data may exhaust the metadata, which are more precious in case
the entire device space is allocated to chunks (ie. balance cannot
make the space more compact)
3) performance suffers a bit as the inlined blocks are duplicate and
stored far away on the device.
Proposed fix: set the default to 2048
This fixes namely 1), the total filesysystem space consumption will be on
par with other filesystems.
Partially fixes 2), more data are pushed to the data block groups.
The characteristics of 3) are based on actual small file size
distribution.
The change is independent of the metadata blockgroup type (though it's
most visible with DUP) or system page size as these parameters are not
trival to find out, compared to file size.
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 11ea474f74 upstream.
Let's remove the error message that appears when the tree_id is not
present. This can happen with the quota tree and has been observed in
practice. The applications are supposed to handle -ENOENT and we don't
need to report that in the system log as it's not a fatal error.
Reported-by: Vlastimil Babka <vbabka@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc95f7bfc5 upstream.
truncate_space_check is using btrfs_csum_bytes_to_leaves() but forgetting to
multiply by nodesize so we get an actual byte count. We need a tracepoint here
so that we have the matching reserve for the release that will come later. Also
add a comment to make clear what the intent of truncate_space_check is.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 503785306d upstream.
reada_zone->end is end pos of segment:
end = start + cache->key.offset - 1;
So we need to use "<=" in condition to judge is a pos in the
segment.
The problem happened rearly, because logical pos rarely pointed
to last 4k of a blockgroup, but we need to fix it to make code
right in logic.
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c47b9e0944 upstream.
Switch the order of the loops to walk the rates on the top
so we exhaust all DP 1.1 rate/lane combinations before trying
DP 1.2 rate/lane combos.
This avoids selecting rates that are supported by the monitor,
but not the connector leading to valid modes getting rejected.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=95206
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff0bd441bd upstream.
Switch the order of the loops to walk the rates on the top
so we exhaust all DP 1.1 rate/lane combinations before trying
DP 1.2 rate/lane combos.
This avoids selecting rates that are supported by the monitor,
but not the connector leading to valid modes getting rejected.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=95206
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a738347df upstream.
There is an issue observed when we hotplug a second DP
4K monitor to the system. Sometimes, the link training
fails for the second monitor after HPD interrupt
generation.
The issue happens when some queued or deferred transactions
are already present on the AUX channel when we initiate
a new transcation to (say) get DPCD or during link training.
We set AUX_IGNORE_HPD_DISCON bit in the AUX_CONTROL
register so that we can ignore any such deferred
transactions when a new AUX transaction is initiated.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e3c00d8784 upstream.
On DCE6.1 PPLL2 is exclusively available to UNIPHYA, so it should not
be taken into consideration when looking for an already enabled PLL
to be shared with other outputs.
This fixes the broken VGA port (TRAVIS DP->VGA bridge) on my Richland
based laptop, where the internal display is connected to UNIPHYA through
a TRAVIS DP->LVDS bridge.
Bug:
https://bugs.freedesktop.org/show_bug.cgi?id=78987
v2: agd: add check in radeon_get_shared_nondp_ppll as well, drop
extra parameter.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a04e23d42a upstream.
Update CDCLK_FREQ on BDW after changing the cdclk frequency. Not sure
if this is a late addition to the spec, or if I simply overlooked this
step when writing the original code.
This is what Bspec has to say about CDCLK_FREQ:
"Program this field to the CD clock frequency minus one. This is used to
generate a divided down clock for miscellaneous timers in display."
And the "Broadwell Sequences for Changing CD Clock Frequency" section
clarifies this further:
"For CD clock 337.5 MHz, program 337 decimal.
For CD clock 450 MHz, program 449 decimal.
For CD clock 540 MHz, program 539 decimal.
For CD clock 675 MHz, program 674 decimal."
Cc: Mika Kahola <mika.kahola@intel.com>
Fixes: b432e5cfd5 ("drm/i915: BDW clock change support")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461689194-6079-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
(cherry picked from commit 7f1052a8fa)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ae645d5fa upstream.
NULL pointer derefence happens when booting with DTB because the
platform data for haptic device is not set in supplied data from parent
MFD device.
The MFD device creates only platform data (from Device Tree) for itself,
not for haptic child.
Unable to handle kernel NULL pointer dereference at virtual address 0000009c
pgd = c0004000
[0000009c] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
(max8997_haptic_probe) from [<c03f9cec>] (platform_drv_probe+0x4c/0xb0)
(platform_drv_probe) from [<c03f8440>] (driver_probe_device+0x214/0x2c0)
(driver_probe_device) from [<c03f8598>] (__driver_attach+0xac/0xb0)
(__driver_attach) from [<c03f67ac>] (bus_for_each_dev+0x68/0x9c)
(bus_for_each_dev) from [<c03f7a38>] (bus_add_driver+0x1a0/0x218)
(bus_add_driver) from [<c03f8db0>] (driver_register+0x78/0xf8)
(driver_register) from [<c0101774>] (do_one_initcall+0x90/0x1d8)
(do_one_initcall) from [<c0a00dbc>] (kernel_init_freeable+0x15c/0x1fc)
(kernel_init_freeable) from [<c06bb5b4>] (kernel_init+0x8/0x114)
(kernel_init) from [<c0107938>] (ret_from_fork+0x14/0x3c)
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: 104594b01c ("Input: add driver support for MAX8997-haptic")
[k.kozlowski: Write commit message, add CC-stable]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 99d825822e upstream.
Payloads of NM entries are not supposed to contain NUL. When we run
into such, only the part prior to the first NUL goes into the
concatenation (i.e. the directory entry name being encoded by a bunch
of NM entries). We do stop when the amount collected so far + the
claimed amount in the current NM entry exceed 254. So far, so good,
but what we return as the total length is the sum of *claimed*
sizes, not the actual amount collected. And that can grow pretty
large - not unlimited, since you'd need to put CE entries in
between to be able to get more than the maximum that could be
contained in one isofs directory entry / continuation chunk and
we are stop once we'd encountered 32 CEs, but you can get about 8Kb
easily. And that's what will be passed to readdir callback as the
name length. 8Kb __copy_to_user() from a buffer allocated by
__get_free_page()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 106b816cb4 upstream.
At the end of process_filter(), collapse_tree() was changed to update
the parg parameter, but the reassignment after the call wasn't removed.
What happens is that the "current_op" gets modified and freed and parg
is assigned to the new allocated argument. But after the call to
collapse_tree(), parg is assigned again to the just freed "current_op",
and this causes the tool to crash.
The current_op variable must also be assigned to NULL in case of error,
otherwise it will cause it to be free()ed twice.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Fixes: 42d6194d13 ("tools lib traceevent: Refactor process_filter()")
Link: http://lkml.kernel.org/r/20160511150936.678c18a1@gandalf.local.home
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2bcbc81421 upstream.
The qla1280 driver sets the scsi_host_template's can_queue field to 0xfffff
which results in an allocation failure when allocating the block layer tags
for the driver's queues. This was introduced with the change for host wide
tags in commit 64d513ac31 - "scsi: use host wide tags by default".
Reduce can_queue to MAX_OUTSTANDING_COMMANDS (512) to solve the allocation
error.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Fixes: 64d513ac31 - "scsi: use host wide tags by default"
Cc: Laura Abbott <labbott@redhat.com>
Cc: Michael Reed <mdr@sgi.com>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <jejb@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 10c64cea04 upstream.
* if we have a hashed negative dentry and either CREAT|EXCL on
r/o filesystem, or CREAT|TRUNC on r/o filesystem, or CREAT|EXCL
with failing may_o_create(), we should fail with EROFS or the
error may_o_create() has returned, but not ENOENT. Which is what
the current code ends up returning.
* if we have CREAT|TRUNC hitting a regular file on a read-only
filesystem, we can't fail with EROFS here. At the very least,
not until we'd done follow_managed() - we might have a writable
file (or a device, for that matter) bound on top of that one.
Moreover, the code downstream will see that O_TRUNC and attempt
to grab the write access (*after* following possible mount), so
if we really should fail with EROFS, it will happen. No need
to do that inside atomic_open().
The real logics is much simpler than what the current code is
trying to do - if we decided to go for simple lookup, ended
up with a negative dentry *and* had create_error set, fail with
create_error. No matter whether we'd got that negative dentry
from lookup_real() or had found it in dcache.
Acked-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a2262e5a12 upstream.
The minium voltage of 1800mV is a copy and paste error from the axp20x
regulator info. The correct minimum voltage for the ldo_io regulators
on the axp22x is 700mV.
Fixes: 1b82b4e4f9 ("regulator: axp20x: Add support for AXP22X regulators")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3b67262307 upstream.
The buck9 regulator of S2MPS11 PMIC had incorrect vsel_mask (0xff
instead of 0x1f) thus reading entire register as buck9's voltage. This
effectively caused regulator core to interpret values as higher voltages
than they were and then to set real voltage much lower than intended.
The buck9 provides power to other regulators, including LDO13
and LDO19 which supply the MMC2 (SD card). On Odroid XU3/XU4 the lower
voltage caused SD card detection errors on Odroid XU3/XU4:
mmc1: card never left busy state
mmc1: error -110 whilst initialising SD card
During driver probe the regulator core was checking whether initial
voltage matches the constraints. With incorrect vsel_mask of 0xff and
default value of 0x50, the core interpreted this as 5 V which is outside
of constraints (3-3.775 V). Then the regulator core was adjusting the
voltage to match the constraints. With incorrect vsel_mask this new
voltage mapped to a vere low voltage in the driver.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f7c17d26f4 upstream.
------------[ cut here ]------------
WARNING: CPU: 0 PID: 16 at kernel/workqueue.c:4559 rebind_workers+0x1c0/0x1d0
Modules linked in:
CPU: 0 PID: 16 Comm: cpuhp/0 Not tainted 4.6.0-rc4+ #31
Hardware name: IBM IBM System x3550 M4 Server -[7914IUW]-/00Y8603, BIOS -[D7E128FUS-1.40]- 07/23/2013
0000000000000000 ffff881037babb58 ffffffff8139d885 0000000000000010
0000000000000000 0000000000000000 0000000000000000 ffff881037babba8
ffffffff8108505d ffff881037ba0000 000011cf3e7d6e60 0000000000000046
Call Trace:
dump_stack+0x89/0xd4
__warn+0xfd/0x120
warn_slowpath_null+0x1d/0x20
rebind_workers+0x1c0/0x1d0
workqueue_cpu_up_callback+0xf5/0x1d0
notifier_call_chain+0x64/0x90
? trace_hardirqs_on_caller+0xf2/0x220
? notify_prepare+0x80/0x80
__raw_notifier_call_chain+0xe/0x10
__cpu_notify+0x35/0x50
notify_down_prepare+0x5e/0x80
? notify_prepare+0x80/0x80
cpuhp_invoke_callback+0x73/0x330
? __schedule+0x33e/0x8a0
cpuhp_down_callbacks+0x51/0xc0
cpuhp_thread_fun+0xc1/0xf0
smpboot_thread_fn+0x159/0x2a0
? smpboot_create_threads+0x80/0x80
kthread+0xef/0x110
? wait_for_completion+0xf0/0x120
? schedule_tail+0x35/0xf0
ret_from_fork+0x22/0x50
? __init_kthread_worker+0x70/0x70
---[ end trace eb12ae47d2382d8f ]---
notify_down_prepare: attempt to take down CPU 0 failed
This bug can be reproduced by below config w/ nohz_full= all cpus:
CONFIG_BOOTPARAM_HOTPLUG_CPU0=y
CONFIG_DEBUG_HOTPLUG_CPU0=y
CONFIG_NO_HZ_FULL=y
As Thomas pointed out:
| If a down prepare callback fails, then DOWN_FAILED is invoked for all
| callbacks which have successfully executed DOWN_PREPARE.
|
| But, workqueue has actually two notifiers. One which handles
| UP/DOWN_FAILED/ONLINE and one which handles DOWN_PREPARE.
|
| Now look at the priorities of those callbacks:
|
| CPU_PRI_WORKQUEUE_UP = 5
| CPU_PRI_WORKQUEUE_DOWN = -5
|
| So the call order on DOWN_PREPARE is:
|
| CB 1
| CB ...
| CB workqueue_up() -> Ignores DOWN_PREPARE
| CB ...
| CB X ---> Fails
|
| So we call up to CB X with DOWN_FAILED
|
| CB 1
| CB ...
| CB workqueue_up() -> Handles DOWN_FAILED
| CB ...
| CB X-1
|
| So the problem is that the workqueue stuff handles DOWN_FAILED in the up
| callback, while it should do it in the down callback. Which is not a good idea
| either because it wants to be called early on rollback...
|
| Brilliant stuff, isn't it? The hotplug rework will solve this problem because
| the callbacks become symetric, but for the existing mess, we need some
| workaround in the workqueue code.
The boot CPU handles housekeeping duty(unbound timers, workqueues,
timekeeping, ...) on behalf of full dynticks CPUs. It must remain
online when nohz full is enabled. There is a priority set to every
notifier_blocks:
workqueue_cpu_up > tick_nohz_cpu_down > workqueue_cpu_down
So tick_nohz_cpu_down callback failed when down prepare cpu 0, and
notifier_blocks behind tick_nohz_cpu_down will not be called any
more, which leads to workers are actually not unbound. Then hotplug
state machine will fallback to undo and online cpu 0 again. Workers
will be rebound unconditionally even if they are not unbound and
trigger the warning in this progress.
This patch fix it by catching !DISASSOCIATED to avoid rebind bound
workers.
Cc: Tejun Heo <tj@kernel.org>
Cc: Lai Jiangshan <jiangshanlai@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Frédéric Weisbecker <fweisbec@gmail.com>
Suggested-by: Lai Jiangshan <jiangshanlai@gmail.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aab0a4c83c upstream.
The memory range assigned to the PMC (Power Management Controller) was
not including the PMC_PCR register which are used to control peripheral
clocks.
This was working fine thanks to the page granularity of ioremap(), but
started to fail when we switched to syscon/regmap, because regmap is
making sure that all accesses are falling into the reserved range.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Richard Genoud <richard.genoud@gmail.com>
Tested-by: Richard Genoud <richard.genoud@gmail.com>
Fixes: 863a81c3be ("clk: at91: make use of syscon to share PMC registers in several drivers")
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9409e22acd upstream.
If a file is renamed to a hardlink of itself POSIX specifies that rename(2)
should do nothing and return success.
This condition is checked in vfs_rename(). However it won't detect hard
links on overlayfs where these are given separate inodes on the overlayfs
layer.
Overlayfs itself detects this condition and returns success without doing
anything, but then vfs_rename() will proceed as if this was a successful
rename (detach_mounts(), d_move()).
The correct thing to do is to detect this condition before even calling
into overlayfs. This patch does this by calling vfs_select_inode() to get
the underlying inodes.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dec8e8f6e6 upstream.
Specifically for the case of reads that use the Extended Register
Read Long command, a multi-byte read operation is broken up into
8-byte chunks. However the call to spmi_ext_register_readl() is
incorrectly passing 'val_size', which if greater than 8 will
always fail. The argument should instead be 'len'.
Fixes: c9afbb05a9 ("regmap: spmi: support base and extended register spaces")
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5305a7b7e8 upstream.
The default configuration of a pin is often with a value in the
pull-up/down field at chip reset. So, even if the internal logic of the
controller prevents writing a configuration with pull-up and pull-down at
the same time, we must ensure explicitly this condition before writing the
register.
This was leading to a pull-down condition not taken into account for
instance.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: 776180848b ("pinctrl: introduce driver for Atmel PIO4 controller")
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ff7760ff6 upstream.
We clamp frame_len_words to a maximum of 4096, but do not actually
limit the number of words written or read through the DATA registers
or the length added to spi_message::actual_length. This results in
silent data corruption for commands longer than this maximum.
Recalculate the length of each transfer, taking frame_len_words into
account. Use this length in qspi_{read,write}_msg(), and to increment
spi_message::actual_length.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea1b60fb08 upstream.
Each transfer can specify 8, 16 or 32 bits per word independently of
the default for the device being addressed. However, currently we
calculate the number of words in the frame assuming that the word size
is the device default.
If multiple transfers in the same message have differing
bits_per_word, we bitwise-or the different values in the WLEN register
field.
Fix both of these. Also rename 'frame_length' to 'frame_len_words' to
make clear that it's not a byte count like spi_message::frame_length.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66ec246eb9 upstream.
Certain Intel Sunrisepoint PCH variants report zero chip selects in SPI
capabilities register even they have one per port. Detection in
pxa2xx_spi_probe() sets master->num_chipselect to 0 leading to -EINVAL
from spi_register_master() where chip select count is validated.
Fix this by not using SPI capabilities register on Sunrisepoint. They don't
have more than one chip select so use the default value 1 instead of
detection.
Fixes: 8b136baa58 ("spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals")
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit addacd801e upstream.
The HD-audio reconfig function got broken in the recent kernels,
typically resulting in a failure like:
snd_hda_intel 0000:00:1b.0: control 3:0:0:Playback Channel Map:0 is already present
This is because of the code restructuring to move the PCM and control
instantiation into the codec drive probe, by the commit [bcd96557bd:
ALSA: hda - Build PCMs and controls at codec driver probe]. Although
the commit above removed the calls of snd_hda_codec_build_pcms() and
*_build_controls() at the controller driver probe, the similar calls
in the reconfig were still left forgotten. This caused the
conflicting and duplicated PCMs and controls.
The fix is trivial: just remove these superfluous calls from
reconfig_codec().
Fixes: bcd96557bd ('ALSA: hda - Build PCMs and controls at codec driver probe')
Reported-by: Jochen Henneberg <jh@henneberg-systemdesign.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2d2c038a99 upstream.
Phoenix Audio MT202pcs (1de7:0114) and MT202exe (1de7:0013) need the
same workaround as TMX320 for avoiding the firmware bug. It fixes the
frequent error about the sample rate inquiries and the slow device
probe as consequence.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=117321
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df27b26f04 upstream.
As akcipher uses an SG interface, you must not use vmalloc memory
as input for it. This patch fixes testmgr to copy the vmalloc
test vectors to kmalloc memory before running the test.
This patch also removes a superfluous sg_virt call in do_test_rsa.
Reported-by: Anatoly Pugachev <matorola@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 13f4bb78cf upstream.
The crypto hash walk code is broken when supplied with an offset
greater than or equal to PAGE_SIZE. This patch fixes it by adjusting
walk->pg and walk->offset when this happens.
Reported-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6d0a07edd1 upstream.
This will provide fully accuracy to the mapcount calculation in the
write protect faults, so page pinning will not get broken by false
positive copy-on-writes.
total_mapcount() isn't the right calculation needed in
reuse_swap_page(), so this introduces a page_trans_huge_mapcount()
that is effectively the full accurate return value for page_mapcount()
if dealing with Transparent Hugepages, however we only use the
page_trans_huge_mapcount() during COW faults where it strictly needed,
due to its higher runtime cost.
This also provide at practical zero cost the total_mapcount
information which is needed to know if we can still relocate the page
anon_vma to the local vma. If page_trans_huge_mapcount() returns 1 we
can reuse the page no matter if it's a pte or a pmd_trans_huge
triggering the fault, but we can only relocate the page anon_vma to
the local vma->anon_vma if we're sure it's only this "vma" mapping the
whole THP physical range.
Kirill A. Shutemov discovered the problem with moving the page
anon_vma to the local vma->anon_vma in a previous version of this
patch and another problem in the way page_move_anon_rmap() was called.
Andrew Morton discovered that CONFIG_SWAP=n wouldn't build in a
previous version, because reuse_swap_page must be a macro to call
page_trans_huge_mapcount from swap.h, so this uses a macro again
instead of an inline function. With this change at least it's a less
dangerous usage than it was before, because "page" is used only once
now, while with the previous code reuse_swap_page(page++) would have
called page_mapcount on page+1 and it would have increased page twice
instead of just once.
Dean Luick noticed an uninitialized variable that could result in a
rmap inefficiency for the non-THP case in a previous version.
Mike Marciniszyn said:
: Our RDMA tests are seeing an issue with memory locking that bisects to
: commit 61f5d698cc ("mm: re-enable THP")
:
: The test program registers two rather large MRs (512M) and RDMA
: writes data to a passive peer using the first and RDMA reads it back
: into the second MR and compares that data. The sizes are chosen randomly
: between 0 and 1024 bytes.
:
: The test will get through a few (<= 4 iterations) and then gets a
: compare error.
:
: Tracing indicates the kernel logical addresses associated with the individual
: pages at registration ARE correct , the data in the "RDMA read response only"
: packets ARE correct.
:
: The "corruption" occurs when the packet crosse two pages that are not physically
: contiguous. The second page reads back as zero in the program.
:
: It looks like the user VA at the point of the compare error no longer points to
: the same physical address as was registered.
:
: This patch totally resolves the issue!
Link: http://lkml.kernel.org/r/1462547040-1737-2-git-send-email-aarcange@redhat.com
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Reviewed-by: "Kirill A. Shutemov" <kirill@shutemov.name>
Reviewed-by: Dean Luick <dean.luick@intel.com>
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Tested-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Tested-by: Josh Collier <josh.d.collier@intel.com>
Cc: Marc Haber <mh+linux-kernel@zugschlus.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 44f43e99fe upstream.
zs_can_compact() has two race conditions in its core calculation:
unsigned long obj_wasted = zs_stat_get(class, OBJ_ALLOCATED) -
zs_stat_get(class, OBJ_USED);
1) classes are not locked, so the numbers of allocated and used
objects can change by the concurrent ops happening on other CPUs
2) shrinker invokes it from preemptible context
Depending on the circumstances, thus, OBJ_ALLOCATED can become
less than OBJ_USED, which can result in either very high or
negative `total_scan' value calculated later in do_shrink_slab().
do_shrink_slab() has some logic to prevent those cases:
vmscan: shrink_slab: zs_shrinker_scan+0x0/0x28 [zsmalloc] negative objects to delete nr=-62
vmscan: shrink_slab: zs_shrinker_scan+0x0/0x28 [zsmalloc] negative objects to delete nr=-62
vmscan: shrink_slab: zs_shrinker_scan+0x0/0x28 [zsmalloc] negative objects to delete nr=-64
vmscan: shrink_slab: zs_shrinker_scan+0x0/0x28 [zsmalloc] negative objects to delete nr=-62
vmscan: shrink_slab: zs_shrinker_scan+0x0/0x28 [zsmalloc] negative objects to delete nr=-62
vmscan: shrink_slab: zs_shrinker_scan+0x0/0x28 [zsmalloc] negative objects to delete nr=-62
However, due to the way `total_scan' is calculated, not every
shrinker->count_objects() overflow can be spotted and handled.
To demonstrate the latter, I added some debugging code to do_shrink_slab()
(x86_64) and the results were:
vmscan: OVERFLOW: shrinker->count_objects() == -1 [18446744073709551615]
vmscan: but total_scan > 0: 92679974445502
vmscan: resulting total_scan: 92679974445502
[..]
vmscan: OVERFLOW: shrinker->count_objects() == -1 [18446744073709551615]
vmscan: but total_scan > 0: 22634041808232578
vmscan: resulting total_scan: 22634041808232578
Even though shrinker->count_objects() has returned an overflowed value,
the resulting `total_scan' is positive, and, what is more worrisome, it
is insanely huge. This value is getting used later on in
shrinker->scan_objects() loop:
while (total_scan >= batch_size ||
total_scan >= freeable) {
unsigned long ret;
unsigned long nr_to_scan = min(batch_size, total_scan);
shrinkctl->nr_to_scan = nr_to_scan;
ret = shrinker->scan_objects(shrinker, shrinkctl);
if (ret == SHRINK_STOP)
break;
freed += ret;
count_vm_events(SLABS_SCANNED, nr_to_scan);
total_scan -= nr_to_scan;
cond_resched();
}
`total_scan >= batch_size' is true for a very-very long time and
'total_scan >= freeable' is also true for quite some time, because
`freeable < 0' and `total_scan' is large enough, for example,
22634041808232578. The only break condition, in the given scheme of
things, is shrinker->scan_objects() == SHRINK_STOP test, which is a
bit too weak to rely on, especially in heavy zsmalloc-usage scenarios.
To fix the issue, take a pool stat snapshot and use it instead of
racy zs_stat_get() calls.
Link: http://lkml.kernel.org/r/20160509140052.3389-1-sergey.senozhatsky@gmail.com
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c25a1e0671 upstream.
Commit 702e5bc68a ("ocfs2: use generic posix ACL infrastructure")
refactored code to use posix_acl_create. The problem with this function
is that it is not mindful of the cluster wide inode lock making it
unsuitable for use with ocfs2 inode creation with ACLs. For example,
when used in ocfs2_mknod, this function can cause deadlock as follows.
The parent dir inode lock is taken when calling posix_acl_create ->
get_acl -> ocfs2_iop_get_acl which takes the inode lock again. This can
cause deadlock if there is a blocked remote lock request waiting for the
lock to be downconverted. And same deadlock happened in ocfs2_reflink.
This fix is to revert back using ocfs2_init_acl.
Fixes: 702e5bc68a ("ocfs2: use generic posix ACL infrastructure")
Signed-off-by: Tariq Saeed <tariq.x.saeed@oracle.com>
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Joseph Qi <joseph.qi@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ee0fbd50f upstream.
Commit 743b5f1434 ("ocfs2: take inode lock in ocfs2_iop_set/get_acl()")
introduced this issue. ocfs2_setattr called by chmod command holds
cluster wide inode lock when calling posix_acl_chmod. This latter
function in turn calls ocfs2_iop_get_acl and ocfs2_iop_set_acl. These
two are also called directly from vfs layer for getfacl/setfacl commands
and therefore acquire the cluster wide inode lock. If a remote
conversion request comes after the first inode lock in ocfs2_setattr,
OCFS2_LOCK_BLOCKED will be set. And this will cause the second call to
inode lock from the ocfs2_iop_get_acl() to block indefinetly.
The deleted version of ocfs2_acl_chmod() calls __posix_acl_chmod() which
does not call back into the filesystem. Therefore, we restore
ocfs2_acl_chmod(), modify it slightly for locking as needed, and use that
instead.
Fixes: 743b5f1434 ("ocfs2: take inode lock in ocfs2_iop_set/get_acl()")
Signed-off-by: Tariq Saeed <tariq.x.saeed@oracle.com>
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Joseph Qi <joseph.qi@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 626abd59e5 ]
Currently, when creating or updating a route, no check is performed
in both ipv4 and ipv6 code to the hoplimit value.
The caller can i.e. set hoplimit to 256, and when such route will
be used, packets will be sent with hoplimit/ttl equal to 0.
This commit adds checks for the RTAX_HOPLIMIT value, in both ipv4
ipv6 route code, substituting any value greater than 255 with 255.
This is consistent with what is currently done for ADVMSS and MTU
in the ipv4 code.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 10a81980fc ]
In the very unlikely case __tcp_retransmit_skb() can not use the cloning
done in tcp_transmit_skb(), we need to refresh skb_mstamp before doing
the copy and transmit, otherwise TCP TS val will be an exact copy of
original transmit.
Fixes: 7faee5c0d5 ("tcp: remove TCP_SKB_CB(skb)->when")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 79e4865032 ]
Stack object "dte_facilities" is allocated in x25_rx_call_request(),
which is supposed to be initialized in x25_negotiate_facilities.
However, 5 fields (8 bytes in total) are not initialized. This
object is then copied to userland via copy_to_user, thus infoleak
occurs.
Signed-off-by: Kangjie Lu <kjlu@gatech.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4a91cb61bb ]
glibc's net/if.h contains copies of definitions from linux/if.h and these
conflict and cause build failures if both files are included by application
source code. Changes in uapi headers, which fixed header file dependencies to
include linux/if.h when it was needed, e.g. commit 1ffad83d, made the
net/if.h and linux/if.h incompatibilities visible as build failures for
userspace applications like iproute2 and xtables-addons.
This patch fixes compile errors when glibc net/if.h is included before
linux/if.h:
./linux/if.h:99:21: error: redeclaration of enumerator ‘IFF_NOARP’
./linux/if.h:98:23: error: redeclaration of enumerator ‘IFF_RUNNING’
./linux/if.h:97:26: error: redeclaration of enumerator ‘IFF_NOTRAILERS’
./linux/if.h:96:27: error: redeclaration of enumerator ‘IFF_POINTOPOINT’
./linux/if.h:95:24: error: redeclaration of enumerator ‘IFF_LOOPBACK’
./linux/if.h:94:21: error: redeclaration of enumerator ‘IFF_DEBUG’
./linux/if.h:93:25: error: redeclaration of enumerator ‘IFF_BROADCAST’
./linux/if.h:92:19: error: redeclaration of enumerator ‘IFF_UP’
./linux/if.h:252:8: error: redefinition of ‘struct ifconf’
./linux/if.h:203:8: error: redefinition of ‘struct ifreq’
./linux/if.h:169:8: error: redefinition of ‘struct ifmap’
./linux/if.h:107:23: error: redeclaration of enumerator ‘IFF_DYNAMIC’
./linux/if.h:106:25: error: redeclaration of enumerator ‘IFF_AUTOMEDIA’
./linux/if.h:105:23: error: redeclaration of enumerator ‘IFF_PORTSEL’
./linux/if.h:104:25: error: redeclaration of enumerator ‘IFF_MULTICAST’
./linux/if.h:103:21: error: redeclaration of enumerator ‘IFF_SLAVE’
./linux/if.h:102:22: error: redeclaration of enumerator ‘IFF_MASTER’
./linux/if.h:101:24: error: redeclaration of enumerator ‘IFF_ALLMULTI’
./linux/if.h:100:23: error: redeclaration of enumerator ‘IFF_PROMISC’
The cases where linux/if.h is included before net/if.h need a similar fix in
the glibc side, or the order of include files can be changed userspace
code as a workaround.
This change was tested in x86 userspace on Debian unstable with
scripts/headers_compile_test.sh:
$ make headers_install && \
cd usr/include && ../../scripts/headers_compile_test.sh -l -k
...
cc -Wall -c -nostdinc -I /usr/lib/gcc/i586-linux-gnu/5/include -I /usr/lib/gcc/i586-linux-gnu/5/include-fixed -I . -I /home/mcfrisk/src/linux-2.6/usr/headers_compile_test_include.2uX2zH -I /home/mcfrisk/src/linux-2.6/usr/headers_compile_test_include.2uX2zH/i586-linux-gnu -o /dev/null ./linux/if.h_libc_before_kernel.h
PASSED libc before kernel test: ./linux/if.h
Reported-by: Jan Engelhardt <jengelh@inai.de>
Reported-by: Josh Boyer <jwboyer@fedoraproject.org>
Reported-by: Stephen Hemminger <shemming@brocade.com>
Reported-by: Waldemar Brodkorb <mail@waldemar-brodkorb.de>
Cc: Gabriel Laskar <gabriel@lse.epita.fr>
Signed-off-by: Mikko Rapeli <mikko.rapeli@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 856ce5d083 ]
With the newly introduced helper functions the skb pulling is hidden
in the checksumming function - and undone before returning to the
caller.
The IGMP and MLD query parsing functions in the bridge still
assumed that the skb is pointing to the beginning of the IGMP/MLD
message while it is now kept at the beginning of the IPv4/6 header.
If there is a querier somewhere else, then this either causes
the multicast snooping to stay disabled even though it could be
enabled. Or, if we have the querier enabled too, then this can
create unnecessary IGMP / MLD query messages on the link.
Fixing this by taking the offset between IP and IGMP/MLD header into
account, too.
Fixes: 9afd85c9e4 ("net: Export IGMP/MLD message validation code")
Reported-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 31ca0458a6 ]
get_bridge_ifindices() is used from the old "deviceless" bridge ioctl
calls which aren't called with rtnl held. The comment above says that it is
called with rtnl but that is not really the case.
Here's a sample output from a test ASSERT_RTNL() which I put in
get_bridge_ifindices and executed "brctl show":
[ 957.422726] RTNL: assertion failed at net/bridge//br_ioctl.c (30)
[ 957.422925] CPU: 0 PID: 1862 Comm: brctl Tainted: G W O
4.6.0-rc4+ #157
[ 957.423009] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),
BIOS 1.8.1-20150318_183358- 04/01/2014
[ 957.423009] 0000000000000000 ffff880058adfdf0 ffffffff8138dec5
0000000000000400
[ 957.423009] ffffffff81ce8380 ffff880058adfe58 ffffffffa05ead32
0000000000000001
[ 957.423009] 00007ffec1a444b0 0000000000000400 ffff880053c19130
0000000000008940
[ 957.423009] Call Trace:
[ 957.423009] [<ffffffff8138dec5>] dump_stack+0x85/0xc0
[ 957.423009] [<ffffffffa05ead32>]
br_ioctl_deviceless_stub+0x212/0x2e0 [bridge]
[ 957.423009] [<ffffffff81515beb>] sock_ioctl+0x22b/0x290
[ 957.423009] [<ffffffff8126ba75>] do_vfs_ioctl+0x95/0x700
[ 957.423009] [<ffffffff8126c159>] SyS_ioctl+0x79/0x90
[ 957.423009] [<ffffffff8163a4c0>] entry_SYSCALL_64_fastpath+0x23/0xc1
Since it only reads bridge ifindices, we can use rcu to safely walk the net
device list. Also remove the wrong rtnl comment above.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dedc58e067 ]
The peer may be expecting a reply having sent a request and then done a
shutdown(SHUT_WR), so tearing down the whole socket at this point seems
wrong and breaks for me with a client which does a SHUT_WR.
Looking at other socket family's stream_recvmsg callbacks doing a shutdown
here does not seem to be the norm and removing it does not seem to have
had any adverse effects that I can see.
I'm using Stefan's RFC virtio transport patches, I'm unsure of the impact
on the vmci transport.
Signed-off-by: Ian Campbell <ian.campbell@docker.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Cc: Andy King <acking@vmware.com>
Cc: Dmitry Torokhov <dtor@vmware.com>
Cc: Jorgen Hansen <jhansen@vmware.com>
Cc: Adit Ranadive <aditr@vmware.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 82d69203df ]
Use htons instead of unconditionally byte swapping nexthdr. On a little
endian systems shifting the byte is correct behavior, but it results in
incorrect csums on big endian architectures.
Fixes: f8c6455bb0 ('net/mlx4_en: Extend checksum offloading by CHECKSUM COMPLETE')
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Carol Soto <clsoto@us.ibm.com>
Tested-by: Carol Soto <clsoto@us.ibm.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5f8e44741f ]
The stack object “map” has a total size of 32 bytes. Its last 4
bytes are padding generated by compiler. These padding bytes are
not initialized and sent out via “nla_put”.
Signed-off-by: Kangjie Lu <kjlu@gatech.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b8670c09f3 ]
The stack object “info” has a total size of 12 bytes. Its last byte
is padding which is not initialized and leaked via “put_cmsg”.
Signed-off-by: Kangjie Lu <kjlu@gatech.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1c021bb717 ]
In the receive path a queue's work bit was cleared unconditionally even
if fec_enet_rx_queue only read out a part of the available packets from
the hardware. This resulted in not reading any packets in the next napi
turn and so packets were delayed or lost.
The obvious fix is to only clear a queue's bit when the queue was
emptied.
Fixes: 4d494cdc92 ("net: fec: change data structure to support multiqueue")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Fugang Duan <fugang.duan@nxp.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6071bd1aa1 ]
This was recently reported to me, and reproduced on the latest net kernel,
when attempting to run netperf from a host that had a netem qdisc attached
to the egress interface:
[ 788.073771] ---------------------[ cut here ]---------------------------
[ 788.096716] WARNING: at net/core/dev.c:2253 skb_warn_bad_offload+0xcd/0xda()
[ 788.129521] bnx2: caps=(0x00000001801949b3, 0x0000000000000000) len=2962
data_len=0 gso_size=1448 gso_type=1 ip_summed=3
[ 788.182150] Modules linked in: sch_netem kvm_amd kvm crc32_pclmul ipmi_ssif
ghash_clmulni_intel sp5100_tco amd64_edac_mod aesni_intel lrw gf128mul
glue_helper ablk_helper edac_mce_amd cryptd pcspkr sg edac_core hpilo ipmi_si
i2c_piix4 k10temp fam15h_power hpwdt ipmi_msghandler shpchp acpi_power_meter
pcc_cpufreq nfsd auth_rpcgss nfs_acl lockd grace sunrpc ip_tables xfs libcrc32c
sd_mod crc_t10dif crct10dif_generic mgag200 syscopyarea sysfillrect sysimgblt
i2c_algo_bit drm_kms_helper ahci ata_generic pata_acpi ttm libahci
crct10dif_pclmul pata_atiixp tg3 libata crct10dif_common drm crc32c_intel ptp
serio_raw bnx2 r8169 hpsa pps_core i2c_core mii dm_mirror dm_region_hash dm_log
dm_mod
[ 788.465294] CPU: 16 PID: 0 Comm: swapper/16 Tainted: G W
------------ 3.10.0-327.el7.x86_64 #1
[ 788.511521] Hardware name: HP ProLiant DL385p Gen8, BIOS A28 12/17/2012
[ 788.542260] ffff880437c036b8 f7afc56532a53db9 ffff880437c03670
ffffffff816351f1
[ 788.576332] ffff880437c036a8 ffffffff8107b200 ffff880633e74200
ffff880231674000
[ 788.611943] 0000000000000001 0000000000000003 0000000000000000
ffff880437c03710
[ 788.647241] Call Trace:
[ 788.658817] <IRQ> [<ffffffff816351f1>] dump_stack+0x19/0x1b
[ 788.686193] [<ffffffff8107b200>] warn_slowpath_common+0x70/0xb0
[ 788.713803] [<ffffffff8107b29c>] warn_slowpath_fmt+0x5c/0x80
[ 788.741314] [<ffffffff812f92f3>] ? ___ratelimit+0x93/0x100
[ 788.767018] [<ffffffff81637f49>] skb_warn_bad_offload+0xcd/0xda
[ 788.796117] [<ffffffff8152950c>] skb_checksum_help+0x17c/0x190
[ 788.823392] [<ffffffffa01463a1>] netem_enqueue+0x741/0x7c0 [sch_netem]
[ 788.854487] [<ffffffff8152cb58>] dev_queue_xmit+0x2a8/0x570
[ 788.880870] [<ffffffff8156ae1d>] ip_finish_output+0x53d/0x7d0
...
The problem occurs because netem is not prepared to handle GSO packets (as it
uses skb_checksum_help in its enqueue path, which cannot manipulate these
frames).
The solution I think is to simply segment the skb in a simmilar fashion to the
way we do in __dev_queue_xmit (via validate_xmit_skb), with some minor changes.
When we decide to corrupt an skb, if the frame is GSO, we segment it, corrupt
the first segment, and enqueue the remaining ones.
tested successfully by myself on the latest net kernel, to which this applies
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Jamal Hadi Salim <jhs@mojatatu.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: netem@lists.linux-foundation.org
CC: eric.dumazet@gmail.com
CC: stephen@networkplumber.org
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 431e3a8e36 ]
We saw qlen!=0 but backlog==0 on our production machine:
qdisc htb 1: dev eth0 root refcnt 2 r2q 10 default 1 direct_packets_stat 0 ver 3.17
Sent 172680457356 bytes 222469449 pkt (dropped 0, overlimits 123575834 requeues 0)
backlog 0b 72p requeues 0
The problem is we only count qlen for HTB qdisc but not backlog.
We need to update backlog too when we update qlen, so that we
can at least know the average packet length.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2ccccf5fb4 ]
When the bottom qdisc decides to, for example, drop some packet,
it calls qdisc_tree_decrease_qlen() to update the queue length
for all its ancestors, we need to update the backlog too to
keep the stats on root qdisc accurate.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b7f8fe251e ]
iptunnel_pull_header expects that IP header was already pulled; with this
expectation, it pulls the tunnel header. This is not true in gre_err.
Furthermore, ipv4_update_pmtu and ipv4_redirect expect that skb->data points
to the IP header.
We cannot pull the tunnel header in this path. It's just a matter of not
calling iptunnel_pull_header - we don't need any of its effects.
Fixes: bda7bb4634 ("gre: Allow multiple protocol listener for gre protocol.")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2c94b53738 ]
Prior to commit d92cff89a0 ("net_dbg_ratelimited: turn into no-op
when !DEBUG") the implementation of net_dbg_ratelimited() was buggy
for both the DEBUG and CONFIG_DYNAMIC_DEBUG cases.
The bug was that net_ratelimit() was being called and, despite
returning true, nothing was being printed to the console. This
resulted in messages like the following -
"net_ratelimit: %d callbacks suppressed"
with no other output nearby.
After commit d92cff89a0 ("net_dbg_ratelimited: turn into no-op when
!DEBUG") the bug is fixed for the DEBUG case. However, there's no
output at all for CONFIG_DYNAMIC_DEBUG case.
This patch restores debug output (if enabled) for the
CONFIG_DYNAMIC_DEBUG case.
Add a definition of net_dbg_ratelimited() for the CONFIG_DYNAMIC_DEBUG
case. The implementation takes care to check that dynamic debugging is
enabled before calling net_ratelimit().
Fixes: d92cff89a0 ("net_dbg_ratelimited: turn into no-op when !DEBUG")
Signed-off-by: Tim Bingham <tbingham@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 569cc39d39 ]
llvm cannot always recognize memset as builtin function and optimize
it away, so just delete it. It was a leftover from testing
of bpf_perf_event_output() with large data structures.
Fixes: 39111695b1 ("samples: bpf: add bpf_perf_event_output example")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6aff67c85c ]
The commit 35578d7984 ("bpf: Implement function bpf_perf_event_read() that get the selected hardware PMU conuter")
introduced clever way to check bpf_helper<->map_type compatibility.
Later on commit a43eec3042 ("bpf: introduce bpf_perf_event_output() helper") adjusted
the logic and inadvertently broke it.
Get rid of the clever bool compare and go back to two-way check
from map and from helper perspective.
Fixes: a43eec3042 ("bpf: introduce bpf_perf_event_output() helper")
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 92117d8443 ]
On a system with >32Gbyte of phyiscal memory and infinite RLIMIT_MEMLOCK,
the malicious application may overflow 32-bit bpf program refcnt.
It's also possible to overflow map refcnt on 1Tb system.
Impose 32k hard limit which means that the same bpf program or
map cannot be shared by more than 32k processes.
Fixes: 1be7f75d16 ("bpf: enable non-root eBPF programs")
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8358b02bf6 ]
When bpf(BPF_PROG_LOAD, ...) was invoked with a BPF program whose bytecode
references a non-map file descriptor as a map file descriptor, the error
handling code called fdput() twice instead of once (in __bpf_map_get() and
in replace_map_fd_with_map_ptr()). If the file descriptor table of the
current task is shared, this causes f_count to be decremented too much,
allowing the struct file to be freed while it is still in use
(use-after-free). This can be exploited to gain root privileges by an
unprivileged user.
This bug was introduced in
commit 0246e64d9a ("bpf: handle pseudo BPF_LD_IMM64 insn"), but is only
exploitable since
commit 1be7f75d16 ("bpf: enable non-root eBPF programs") because
previously, CAP_SYS_ADMIN was required to reach the vulnerable code.
(posted publicly according to request by maintainer)
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 391a20333b ]
After commit fbd40ea018 ("ipv4: Don't do expensive useless work
during inetdev destroy.") when deleting an interface,
fib_del_ifaddr() can be executed without any primary address
present on the dead interface.
The above is safe, but triggers some "bug: prim == NULL" warnings.
This commit avoids warning if the in_dev is dead
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cd255efff9 ]
Set and report vport MTU rather than physical MTU,
Driver will set both vport and physical port mtu and will
rely on the query of vport mtu.
SRIOV VFs have to report their MTU to their vport manager (PF),
and this will allow them to work with any MTU they need
without failing the request.
Also for some cases where the PF is not a port owner, PF can
work with MTU less than the physical port mtu if set physical
port mtu didn't take effect.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d8edd2469a ]
Minimum MTU that can be set in Connectx4 device is 68.
This fixes the case where a user wants to set invalid MTU,
the driver will fail to satisfy this request and the interface
will stay down.
It is better to report an error and continue working with old
mtu.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 046339eaab ]
For set/query MTU port firmware commands the MTU field
is 16 bits, here I changed all the "int mtu" parameters
of the functions wrapping those firmware commands to be u16.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c3f9bf628b ]
In the error flow of adding flow rule to auto-grouped flow
table, we call to tree_remove_node.
tree_remove_node locks the node's parent, however the node's parent
is already locked by mlx5_add_flow_rule and this causes a deadlock.
After this patch, if we failed to add the flow rule, we unlock the
flow table before calling to tree_remove_node.
fixes: f0d22d1874 ('net/mlx5_core: Introduce flow steering autogrouped
flow table')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reported-by: Amir Vadai <amir@vadai.me>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b4f70527f0 ]
When using masked actions the ipv6_proto field of an action
to set IPv6 fields may be zero rather than the prevailing protocol
which will result in skipping checksum recalculation.
This patch resolves the problem by relying on the protocol
in the flow key rather than that in the set field action.
Fixes: 83d2b9ba1a ("net: openvswitch: Support masked set actions.")
Cc: Jarno Rajahalme <jrajahalme@nicira.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f43bfaeddc ]
atl2 includes NETIF_F_SG in hw_features even though it has no support
for non-linear skbs. This bug was originally harmless since the
driver does not claim to implement checksum offload and that used to
be a requirement for SG.
Now that SG and checksum offload are independent features, if you
explicitly enable SG *and* use one of the rare protocols that can use
SG without checkusm offload, this potentially leaks sensitive
information (before you notice that it just isn't working). Therefore
this obscure bug has been designated CVE-2016-2117.
Reported-by: Justin Yackoski <jyackoski@crypto-nite.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: ec5f061564 ("net: Kill link between CSUM and SG features.")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9241e2df4f ]
When __vlan_insert_tag() fails from skb_vlan_push() path due to the
skb_cow_head(), we need to undo the __skb_push() in the error path
as well that was done earlier to move skb->data pointer to mac header.
Moreover, I noticed that when in the non-error path the __skb_pull()
is done and the original offset to mac header was non-zero, we fixup
from a wrong skb->data offset in the checksum complete processing.
So the skb_postpush_rcsum() really needs to be done before __skb_pull()
where skb->data still points to the mac header start and thus operates
under the same conditions as in __vlan_insert_tag().
Fixes: 93515d53b1 ("net: move vlan pop/push functions into common code")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d894ba18d4 ]
With the SO_REUSEPORT socket option, it is possible to create sockets
in the AF_INET and AF_INET6 domains which are bound to the same IPv4 address.
This is only possible with SO_REUSEPORT and when not using IPV6_V6ONLY on
the AF_INET6 sockets.
Prior to the commits referenced below, an incoming IPv4 packet would
always be routed to a socket of type AF_INET when this mixed-mode was used.
After those changes, the same packet would be routed to the most recently
bound socket (if this happened to be an AF_INET6 socket, it would
have an IPv4 mapped IPv6 address).
The change in behavior occurred because the recent SO_REUSEPORT optimizations
short-circuit the socket scoring logic as soon as they find a match. They
did not take into account the scoring logic that favors AF_INET sockets
over AF_INET6 sockets in the event of a tie.
To fix this problem, this patch changes the insertion order of AF_INET
and AF_INET6 addresses in the TCP and UDP socket lists when the sockets
have SO_REUSEPORT set. AF_INET sockets will be inserted at the head of the
list and AF_INET6 sockets with SO_REUSEPORT set will always be inserted at
the tail of the list. This will force AF_INET sockets to always be
considered first.
Fixes: e32ea7e747 ("soreuseport: fast reuseport UDP socket selection")
Fixes: 125e80b88687 ("soreuseport: fast reuseport TCP socket selection")
Reported-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: Craig Gallek <kraig@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c5b5343cfb ]
We now have a positive report of another Huawei device needing
this quirk: The ME906s-158 (12d1:15c1). This is an m.2 form
factor modem with no obvious relationship to the E3372 (12d1:157d)
we already have a quirk entry for. This is reason enough to
believe the quirk might be necessary for any number of current
and future Huawei devices.
Applying the quirk to all Huawei devices, since it is crucial
to any device affected by the firmware bug, while the impact
on non-affected devices is negligible.
The quirk can if necessary be disabled per-device by writing
N to /sys/class/net/<iface>/cdc_ncm/ndp_to_end
Reported-by: Andreas Fett <andreas.fett@secunet.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d82bccc690 ]
verifier must check for reserved size bits in instruction opcode and
reject BPF_LD | BPF_ABS | BPF_DW and BPF_LD | BPF_IND | BPF_DW instructions,
otherwise interpreter will WARN_RATELIMIT on them during execution.
Fixes: ddd872bc30 ("bpf: verifier: add checks for BPF_ABS | BPF_IND instructions")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3dcd493fbe ]
A failure in validate_xmit_skb_list() triggered an unconditional call
to dev_requeue_skb with skb=NULL. This slowly grows the queue
discipline's qlen count until all traffic through the queue stops.
We take the optimistic approach and continue running the queue after a
failure since it is unknown if later packets also will fail in the
validate path.
Fixes: 55a93b3ea7 ("qdisc: validate skb without holding lock")
Signed-off-by: Lars Persson <larper@axis.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 309cf37fe2 ]
Because we miss to wipe the remainder of i->addr[] in packet_mc_add(),
pdiag_put_mclist() leaks uninitialized heap bytes via the
PACKET_DIAG_MCLIST netlink attribute.
Fix this by explicitly memset(0)ing the remaining bytes in i->addr[].
Fixes: eea68e2f1a ("packet: Report socket mclist info via diag module")
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Acked-by: Pavel Emelyanov <xemul@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d6d5e999e5 ]
For local routes that require a particular output interface we do not want
to cache the result. Caching the result causes incorrect behaviour when
there are multiple source addresses on the interface. The end result
being that if the intended recipient is waiting on that interface for the
packet he won't receive it because it will be delivered on the loopback
interface and the IP_PKTINFO ipi_ifindex will be set to the loopback
interface as well.
This can be tested by running a program such as "dhcp_release" which
attempts to inject a packet on a particular interface so that it is
received by another program on the same board. The receiving process
should see an IP_PKTINFO ipi_ifndex value of the source interface
(e.g., eth1) instead of the loopback interface (e.g., lo). The packet
will still appear on the loopback interface in tcpdump but the important
aspect is that the CMSG info is correct.
Sample dhcp_release command line:
dhcp_release eth1 192.168.204.222 02:11:33:22:44:66
Signed-off-by: Allain Legacy <allain.legacy@windriver.com>
Signed off-by: Chris Friesen <chris.friesen@windriver.com>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a36a0d4008 ]
In particular, make sure we check for decnet private presence
for loopback devices.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce7b516f3f upstream.
Building wilc1000 with clang currently fails in the staging-next branch:
drivers/staging/wilc1000/wilc_spi.c:123:34: warning: tentative definition of variable with internal linkage has incomplete non-array type 'const struct wilc1000_ops' [-Wtentative-definition-incomplete-type]
static const struct wilc1000_ops wilc1000_spi_ops;
The reason is that wilc1000_ops was left behind after a recent cleanup,
and is completely unused and also uninitialized and const and has an
incomplete type.
Removing the variable is obviously correct, and gets rid of the warning.
No idea why gcc does not complain about it though.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a21211672c upstream.
There are several reports of freeze on enabling HWP (Hardware PStates)
feature on Skylake-based systems by the Intel P-states driver. The root
cause is identified as the HWP interrupts causing BIOS code to freeze.
HWP interrupts use the thermal LVT which can be handled by Linux
natively, but on the affected Skylake-based systems SMM will respond
to it by default. This is a problem for several reasons:
- On the affected systems the SMM thermal LVT handler is broken (it
will crash when invoked) and a BIOS update is necessary to fix it.
- With thermal interrupt handled in SMM we lose all of the reporting
features of the arch/x86/kernel/cpu/mcheck/therm_throt driver.
- Some thermal drivers like x86-package-temp depend on the thermal
threshold interrupts signaled via the thermal LVT.
- The HWP interrupts are useful for debugging and tuning
performance (if the kernel can handle them).
The native handling of thermal interrupts needs to be enabled
because of that.
This requires some way to tell SMM that the OS can handle thermal
interrupts. That can be done by using _OSC/_PDC in processor
scope very early during ACPI initialization.
The meaning of _OSC/_PDC bit 12 in processor scope is whether or
not the OS supports native handling of interrupts for Collaborative
Processor Performance Control (CPPC) notifications. Since on
HWP-capable systems CPPC is a firmware interface to HWP, setting
this bit effectively tells the firmware that the OS will handle
thermal interrupts natively going forward.
For details on _OSC/_PDC refer to:
http://www.intel.com/content/www/us/en/standards/processor-vendor-specific-acpi-specification.html
To implement the _OSC/_PDC handshake as described, introduce a new
function, acpi_early_processor_osc(), that walks the ACPI
namespace looking for ACPI processor objects and invokes _OSC for
them with bit 12 in the capabilities buffer set and terminates the
namespace walk on the first success.
Also modify intel_thermal_interrupt() to clear HWP status bits in
the HWP_STATUS MSR to acknowledge HWP interrupts (which prevents
them from firing continuously).
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Subject & changelog, function rename ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 60b3143c7c upstream.
This patch does the following:
- Fakes live status of HDMI as connected (even if that's not).
While testing certain (monitor + cable) combinations with
various intel platforms, it seems that live status register
doesn't work reliably on some older devices. So limit the
live_status check for HDMI detection, only for platforms
from gen7 onwards.
V2: restrict faking live_status to certain platforms
V3: (Ville)
- keep the debug message for !live_status case
- fix indentation of comment
- remove "warning" from the debug message
(Jani)
- Change format of fix details in the commit message
Fixes: 237ed86c69 ("drm/i915: Check live status before reading edid")
Suggested-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461237606-16491-1-git-send-email-shashank.sharma@intel.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
(cherry picked from commit 4f4a818501)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4ea3959018 upstream.
Somehow my SNB GT1 (Dell XPS 8300) gets very unhappy around
GPU hangs if the RPS EI/thresholds aren't suitably aligned.
It seems like scheduling/timer interupts stop working somehow
and things get stuck eg. in usleep_range().
I bisected the problem down to
commit 8a5864377b ("drm/i915/skl: Restructured the gen6_set_rps_thresholds function")
I observed that before all the values were at least multiples of 25,
but afterwards they are not. And rounding things up to the next multiple
of 25 does seem to help, so lets' do that. I also tried roundup(..., 5)
but that wasn't sufficient. Also I have no idea if we might need this sort of
thing on gen9+ as well.
These are the original EI/thresholds:
LOW_POWER
GEN6_RP_UP_EI 12500
GEN6_RP_UP_THRESHOLD 11800
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 21250
BETWEEN
GEN6_RP_UP_EI 10250
GEN6_RP_UP_THRESHOLD 9225
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 18750
HIGH_POWER
GEN6_RP_UP_EI 8000
GEN6_RP_UP_THRESHOLD 6800
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 15000
These are after 8a5864377b:
LOW_POWER
GEN6_RP_UP_EI 12500
GEN6_RP_UP_THRESHOLD 11875
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 21250
BETWEEN
GEN6_RP_UP_EI 10156
GEN6_RP_UP_THRESHOLD 9140
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 18750
HIGH_POWER
GEN6_RP_UP_EI 7812
GEN6_RP_UP_THRESHOLD 6640
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 15000
And these are what we have after this patch:
LOW_POWER
GEN6_RP_UP_EI 12500
GEN6_RP_UP_THRESHOLD 11875
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 21250
BETWEEN
GEN6_RP_UP_EI 10175
GEN6_RP_UP_THRESHOLD 9150
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 18750
HIGH_POWER
GEN6_RP_UP_EI 7825
GEN6_RP_UP_THRESHOLD 6650
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 15000
Cc: Akash Goel <akash.goel@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Testcase: igt/kms_pipe_crc_basic/hang-read-crc-pipe-B
Fixes: 8a5864377b ("drm/i915/skl: Restructured the gen6_set_rps_thresholds function")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461159836-9108-1-git-send-email-ville.syrjala@linux.intel.com
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
(cherry picked from commit 8a292d016d)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dab9a2663f upstream.
During system resume we depended on pci_enable_device() also putting the
device into PCI D0 state. This won't work if the PCI device was already
enabled but still in D3 state. This is because pci_enable_device() is
refcounted and will not change the HW state if called with a non-zero
refcount. Leaving the device in D3 will make all subsequent device
accesses fail.
This didn't cause a problem most of the time, since we resumed with an
enable refcount of 0. But it fails at least after module reload because
after that we also happen to leak a PCI device enable reference: During
probing we call drm_get_pci_dev() which will enable the PCI device, but
during device removal drm_put_dev() won't disable it. This is a bug of
its own in DRM core, but without much harm as it only leaves the PCI
device enabled. Fixing it is also a bit more involved, due to DRM
mid-layering and because it affects non-i915 drivers too. The fix in
this patch is valid regardless of the problem in DRM core.
v2:
- Add a code comment about the relation of this fix to the freeze/thaw
vs. the suspend/resume phases. (Ville)
- Add a code comment about the inconsistent ordering of set power state
and device enable calls. (Chris)
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460979954-14503-1-git-send-email-imre.deak@intel.com
(cherry picked from commit 44410cd0bf)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5eaa60c710 upstream.
The driver's VDD on/off logic assumes that whenever the VDD is on we
also hold an AUX power domain reference. Since BIOS can leave the VDD on
during booting and resuming and on DDI platforms we won't take a
corresponding power reference, the above assumption won't hold on those
platforms and an eventual delayed VDD off work will do an extraneous AUX
power domain put resulting in a refcount underflow. Fix this the same
way we did this for non-DDI DP encoders:
commit 6d93c0c417 ("drm/i915: fix VDD state tracking after system
resume")
At the same time call the DP encoder suspend handler the same way as the
non-DDI DP encoders do to flush any pending VDD off work. Leaving the
work running may cause a HW access where we don't expect this (at a point
where power domains are suspended already).
While at it remove an unnecessary function call indirection.
This fixed for me AUX refcount underflow problems on BXT during
suspend/resume.
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460963062-13211-4-git-send-email-imre.deak@intel.com
(cherry picked from commit bf93ba67e9)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05be8d4101 upstream.
If i2c_device_id *id is NULL and acpi_match_device returns NULL too,
then chipset may be unitialized when accessing &ak_def_array[chipset] in
ak8975_probe. Therefore initialize chipset to AK_MAX_TYPE, which will
return an error when not changed.
This patch fixes the following maybe-uninitialized warning:
drivers/iio/magnetometer/ak8975.c: In function ‘ak8975_probe’:
drivers/iio/magnetometer/ak8975.c:788:14: warning: ‘chipset’ may be used
uninitialized in this function [-Wmaybe-uninitialized]
data->def = &ak_def_array[chipset];
Signed-off-by: Richard Leitner <dev@g0hl1n.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07d2390e36 upstream.
In certain probe conditions the interrupt came right after registering
the handler causing a NULL pointer exception because of uninitialized
waitqueue:
$ udevadm trigger
i2c-gpio i2c-gpio-1: using pins 143 (SDA) and 144 (SCL)
i2c-gpio i2c-gpio-3: using pins 53 (SDA) and 52 (SCL)
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = e8b38000
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in: snd_soc_i2s(+) i2c_gpio(+) snd_soc_idma snd_soc_s3c_dma snd_soc_core snd_pcm_dmaengine snd_pcm snd_timer snd soundcore ac97_bus spi_s3c64xx pwm_samsung dwc2 exynos_adc phy_exynos_usb2 exynosdrm exynos_rng rng_core rtc_s3c
CPU: 0 PID: 717 Comm: data-provider-m Not tainted 4.6.0-rc1-next-20160401-00011-g1b8d87473b9e-dirty #101
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
(...)
(__wake_up_common) from [<c0379624>] (__wake_up+0x38/0x4c)
(__wake_up) from [<c0a41d30>] (ak8975_irq_handler+0x28/0x30)
(ak8975_irq_handler) from [<c0386720>] (handle_irq_event_percpu+0x88/0x140)
(handle_irq_event_percpu) from [<c038681c>] (handle_irq_event+0x44/0x68)
(handle_irq_event) from [<c0389c40>] (handle_edge_irq+0xf0/0x19c)
(handle_edge_irq) from [<c0385e04>] (generic_handle_irq+0x24/0x34)
(generic_handle_irq) from [<c05ee360>] (exynos_eint_gpio_irq+0x50/0x68)
(exynos_eint_gpio_irq) from [<c0386720>] (handle_irq_event_percpu+0x88/0x140)
(handle_irq_event_percpu) from [<c038681c>] (handle_irq_event+0x44/0x68)
(handle_irq_event) from [<c0389a70>] (handle_fasteoi_irq+0xb4/0x194)
(handle_fasteoi_irq) from [<c0385e04>] (generic_handle_irq+0x24/0x34)
(generic_handle_irq) from [<c03860b4>] (__handle_domain_irq+0x5c/0xb4)
(__handle_domain_irq) from [<c0301774>] (gic_handle_irq+0x54/0x94)
(gic_handle_irq) from [<c030c910>] (__irq_usr+0x50/0x80)
The bug was reproduced on exynos4412-trats2 (with a max77693 device also
using i2c-gpio) after building max77693 as a module.
Fixes: 94a6d5cf7c ("iio:ak8975 Implement data ready interrupt handling")
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0092d3edcb upstream.
Without this there was a double free of the metadata,
which ended up freeing the fd table for me here, and taking
out the machine more often than not.
I reproduced with X.org + modesetting DDX + latest llvm/mesa,
also required using dri3.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 503fe87bd0 upstream.
If of_node is set before calling platform_device_add, the driver core
will try to use of: modalias matching, which fails because the device
tree nodes don't have a compatible property set. This patch fixes
imx-ipuv3-crtc module autoloading by setting the of_node property only
after the platform modalias is set.
Fixes: 304e6be652 ("gpu: ipu-v3: Assign of_node of child platform devices to corresponding ports")
Reported-by: Dennis Gilmore <dennis@ausil.us>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-By: Dennis Gilmore <dennis@ausil.us>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1db488d128 upstream.
On the consumer side, we have interrupt driven flow management of the
producer. It is sufficient to base the signaling decision on the
amount of space that is available to write after the read is complete.
The current code samples the previous available space and uses this
in making the signaling decision. This state can be stale and is
unnecessary. Since the state can be stale, we end up not signaling
the host (when we should) and this can result in a hang. Fix this
problem by removing the unnecessary check. I would like to thank
Arseney Romanenko <arseneyr@microsoft.com> for pointing out this issue.
Also, issue a full memory barrier before making the signaling descision
to correctly deal with potential reordering of the write (read index)
followed by the read of pending_sz.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Tested-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d1306eb675 upstream.
This patch fixes the issue where the mxs_ocotp_read is reading
the ocotp in reg_size steps but decrements the remaining size
by 1. The number of iterations is thus four times higher,
overwriting the area behind the output buffer.
Fixes: c01e9a11ab ("nvmem: add driver for ocotp in i.MX23 and i.MX28")
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Stanislav Meduna <stano@meduna.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9be427efc7 upstream.
This reverts commit e3345db850, which
broke system resume for a large class of devices.
Devices that after having been reset during resume need to be rebound
due to a missing reset_resume callback, are now left in a suspended
state. This specifically broke resume of common USB-serial devices,
which are now unusable after system suspend (until disconnected and
reconnected) when USB persist is enabled.
During resume, usb_resume_interface will set the needs_binding flag for
such interfaces, but unlike system resume, run-time resume does not
honour it.
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d377f4d69 upstream.
The Link ECU is an aftermarket ECU computer for vehicles that provides
full tuning abilities as well as datalogging and displaying capabilities
via the USB to Serial adapter built into the device.
Signed-off-by: Mike Manning <michael@bsch.com.au>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 17dcc37e3e upstream.
On some SOCs PORTS_IMPL register value is never programmed by the
firmware and left at zero value. Which means that no sata ports are
available for software. AHCI driver used to cope up with this by
fabricating the port_map if the PORTS_IMPL register is read zero,
but recent patch broke this workaround as zero value was valid for
NVMe disks.
This patch adds ports-implemented DT bindings as workaround for this issue
in a way that DT can can override the PORTS_IMPL register in cases where
the firmware did not program it already.
Fixes: 566d1827df ("libata: disable forced PORTS_IMPL for >= AHCI 1.3")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2fd0f46cb1 upstream.
In usecases where force_port_map is used saved_port_map is never set,
resulting in not programming the PORTS_IMPL register as part of initial
config. This patch fixes this by setting it to port_map even in case
where force_port_map is used, making it more inline with other parts of
the code.
Fixes: 566d1827df ("libata: disable forced PORTS_IMPL for >= AHCI 1.3")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b4c112114a upstream.
In create_zero_mask() we have:
addi %1,%2,-1
andc %1,%1,%2
popcntd %0,%1
using the "r" constraint for %2. r0 is a valid register in the "r" set,
but addi X,r0,X turns it into an li:
li r7,-1
andc r7,r7,r0
popcntd r4,r7
Fix this by using the "b" constraint, for which r0 is not a valid
register.
This was found with a kernel build using gcc trunk, narrowed down to
when -frename-registers was enabled at -O2. It is just luck however
that we aren't seeing this on older toolchains.
Thanks to Segher for working with me to find this issue.
Fixes: d0cebfa650 ("powerpc: word-at-a-time optimization for 64-bit Little Endian")
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb4add2ce9 upstream.
This patch adds new ports-implemented mask, which is required to get
achi working on the mainline. Without this patch value read from
PORTS_IMPL register which is zero would not enable any ports for
software to use.
Fixes: 566d1827df ("libata: disable forced PORTS_IMPL for >= AHCI 1.3")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e5bc0478ab upstream.
While reviewing a different change to asm-generic/io.h Arnd spotted that
ARC ioread32 and ioread32be both of which come from asm-generic versions
are not symmetrical in terms of calling the io barriers.
generic ioread32 -> ARC readl() [ has barriers]
generic ioread32be -> __be32_to_cpu(__raw_readl()) [ lacks barriers]
While generic ioread32be is being remediated to call readl(), that involves
a swab32(), causing double swaps on ioread32be() on Big Endian systems.
So provide our versions of big endian IO accessors to ensure io barrier
calls while also keeping them optimal
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2482bc31ca upstream.
The sti-cpufreq does unconditional registration of the cpufreq-dt driver
which causes issue on an multi-platform build. For example, on Vexpress
TC2 platform, we get the following error on boot:
cpu cpu0: OPP-v2 not supported
cpu cpu0: Not doing voltage scaling
cpu: dev_pm_opp_of_cpumask_add_table: couldn't find opp table
for cpu:0, -19
cpu cpu0: dev_pm_opp_get_max_volt_latency: Invalid regulator (-6)
...
arm_big_little: bL_cpufreq_register: Failed registering platform driver:
vexpress-spc, err: -17
The actual driver fails to initialise as cpufreq-dt is probed
successfully, which is incorrect. This issue can happen to any platform
not using cpufreq-dt in a multi-platform build.
This patch adds a check to do selective initialization of the driver.
Fixes: ab0ea257fc (cpufreq: st: Provide runtime initialised driver for ST's platforms)
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f0b22d1bb2 upstream.
Do not load one entry beyond the end of the syscall table when the
syscall number of a traced process equals to __NR_Linux_syscalls.
Similar bug with regular processes was fixed by commit 3bb457af4f
("[PARISC] Fix bug when syscall nr is __NR_Linux_syscalls").
This bug was found by strace test suite.
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Acked-by: Helge Deller <deller@gmx.de>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 625fe4f8ff upstream.
arm_cpuidle_suspend() may return -EOPNOTSUPP, or any value returned
by the cpu_ops/cpuidle_ops suspend call. arm_enter_idle_state() doesn't
update 'ret' with this value, meaning we always signal success to
cpuidle_enter_state(), causing it to update the usage counters as if we
succeeded.
Fixes: 191de17aa3 ("ARM64: cpuidle: Replace cpu_suspend by the common ARM/ARM64 function")
Signed-off-by: James Morse <james.morse@arm.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 886123fb3a upstream.
Currently we read the tsc radio: ratio = (MSR_PLATFORM_INFO >> 8) & 0x1f;
Thus we get bit 8-12 of MSR_PLATFORM_INFO, however according to the SDM
(35.5), the ratio bits are bit 8-15.
Ignoring the upper bits can result in an incorrect tsc ratio, which causes the
TSC calibration and the Local APIC timer frequency to be incorrect.
Fix this problem by masking 0xff instead.
[ tglx: Massaged changelog ]
Fixes: 7da7c15613 "x86, tsc: Add static (MSR) TSC calibration on Intel Atom SoCs"
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Bin Gao <bin.gao@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: http://lkml.kernel.org/r/1462505619-5516-1-git-send-email-yu.c.chen@intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 74d3694433 upstream.
Commit 947e9762a8 ("writeback: update wb_over_bg_thresh() to use
wb_domain aware operations") unintentionally changed this function's
meaning from "are there more dirty pages than the background writeback
threshold" to "are there more dirty pages than the writeback threshold".
The background writeback threshold is typically half of the writeback
threshold, so this had the effect of raising the number of dirty pages
required to cause a writeback worker to perform background writeout.
This can cause a very severe performance regression when a BDI uses
BDI_CAP_STRICTLIMIT because balance_dirty_pages() and the writeback worker
can now disagree on whether writeback should be initiated.
For example, in a system having 1GB of RAM, a single spinning disk, and a
"pass-through" FUSE filesystem mounted over the disk, application code
mmapped a 128MB file on the disk and was randomly dirtying pages in that
mapping.
Because FUSE uses strictlimit and has a default max_ratio of only 1%, in
balance_dirty_pages, thresh is ~200, bg_thresh is ~100, and the
dirty_freerun_ceiling is the average of those, ~150. So, it pauses the
dirtying processes when we have 151 dirty pages and wakes up a background
writeback worker. But the worker tests the wrong threshold (200 instead of
100), so it does not initiate writeback and just returns.
Thus, balance_dirty_pages keeps looping, sleeping and then waking up the
worker who will do nothing. It remains stuck in this state until the few
dirty pages that we have finally expire and we write them back for that
reason. Then the whole process repeats, resulting in near-zero throughput
through the FUSE BDI.
The fix is to call the parameterized variant of wb_calc_thresh, so that the
worker will do writeback if the bg_thresh is exceeded which was the
behavior before the referenced commit.
Fixes: 947e9762a8 ("writeback: update wb_over_bg_thresh() to use wb_domain aware operations")
Signed-off-by: Howard Cochran <hcochran@kernelspring.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Tested-by Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 658922e57b upstream.
When configuring a pfn-device instance to allocate the memmap array it
needs to account for the fact that vmemmap_populate_hugepages()
allocates struct page blocks in HPAGE_SIZE chunks. We need to align the
reserved area size to 2MB otherwise arch_add_memory() runs out of memory
while establishing the memmap:
WARNING: CPU: 0 PID: 496 at arch/x86/mm/init_64.c:704 arch_add_memory+0xe7/0xf0
[..]
Call Trace:
[<ffffffff8148bdb3>] dump_stack+0x85/0xc2
[<ffffffff810a749b>] __warn+0xcb/0xf0
[<ffffffff810a75cd>] warn_slowpath_null+0x1d/0x20
[<ffffffff8106a497>] arch_add_memory+0xe7/0xf0
[<ffffffff811d2097>] devm_memremap_pages+0x287/0x450
[<ffffffff811d1ffa>] ? devm_memremap_pages+0x1ea/0x450
[<ffffffffa0000298>] __wrap_devm_memremap_pages+0x58/0x70 [nfit_test_iomap]
[<ffffffffa0047a58>] pmem_attach_disk+0x318/0x420 [nd_pmem]
[<ffffffffa0047bcf>] nd_pmem_probe+0x6f/0x90 [nd_pmem]
[<ffffffffa0009469>] nvdimm_bus_probe+0x69/0x110 [libnvdimm]
[..]
ndbus0: nd_pmem.probe(pfn3.0) = -12
nd_pmem: probe of pfn3.0 failed with error -12
libndctl: ndctl_pfn_enable: pfn3.0: failed to enable
Reported-by: Namratha Kothapalli <namratha.n.kothapalli@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d1a65f1741 upstream.
_batadv_update_route rcu_derefences orig_ifinfo->router outside of a
spinlock protected region to print some information messages to the debug
log. But this pointer is not checked again when the new pointer is assigned
in the spinlock protected region. Thus is can happen that the value of
orig_ifinfo->router changed in the meantime and thus the reference counter
of the wrong router gets reduced after the spinlock protected region.
Just rcu_dereferencing the value of orig_ifinfo->router inside the spinlock
protected region (which also set the new pointer) is enough to get the
correct old router object.
Fixes: e1a5382f97 ("batman-adv: Make orig_node->router an rcu protected pointer")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c4fdb6cff2 upstream.
When removing a single interface while a broadcast or ogm packet is
still pending then we will free the forward packet without releasing the
queue slots again.
This patch is supposed to fix this issue.
Fixes: 6d5808d4ae ("batman-adv: Add missing hardif_free_ref in forw_packet_free")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
[sven@narfation.org: fix conflicts with current version]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c78296665c upstream.
The encapsulated ethernet and VLAN header may be outside the received
ethernet frame. Thus the skb buffer size has to be checked before it can be
parsed to find out if it encapsulates another batman-adv packet.
Fixes: 420193573f ("batman-adv: softif bridge loop avoidance")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2871734e85 upstream.
Now that DAT is VLAN aware, it must use the VID when
computing the DHT address of the candidate nodes where
an entry is going to be stored/retrieved.
Fixes: be1db4f661 ("batman-adv: make the Distributed ARP Table vlan aware")
Signed-off-by: Antonio Quartulli <a@unstable.cc>
[sven@narfation.org: fix conflicts with current version]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bc22af74f2 upstream.
Khugepaged attempts to raise min_free_kbytes if its set too low.
However, on boot khugepaged sets min_free_kbytes first from
subsys_initcall(), and then the mm 'core' over-rides min_free_kbytes
after from init_per_zone_wmark_min(), via a module_init() call.
Khugepaged used to use a late_initcall() to set min_free_kbytes (such
that it occurred after the core initialization), however this was
removed when the initialization of min_free_kbytes was integrated into
the starting of the khugepaged thread.
The fix here is simply to invoke the core initialization using a
core_initcall() instead of module_init(), such that the previous
initialization ordering is restored. I didn't restore the
late_initcall() since start_stop_khugepaged() already sets
min_free_kbytes via set_recommended_min_free_kbytes().
This was noticed when we had a number of page allocation failures when
moving a workload to a kernel with this new initialization ordering. On
an 8GB system this restores min_free_kbytes back to 67584 from 11365
when CONFIG_TRANSPARENT_HUGEPAGE=y is set and either
CONFIG_TRANSPARENT_HUGEPAGE_ALWAYS=y or
CONFIG_TRANSPARENT_HUGEPAGE_MADVISE=y.
Fixes: 79553da293 ("thp: cleanup khugepaged startup")
Signed-off-by: Jason Baron <jbaron@akamai.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8148a73c99 upstream.
If /proc/<PID>/environ gets read before the envp[] array is fully set up
in create_{aout,elf,elf_fdpic,flat}_tables(), we might end up trying to
read more bytes than are actually written, as env_start will already be
set but env_end will still be zero, making the range calculation
underflow, allowing to read beyond the end of what has been written.
Fix this as it is done for /proc/<PID>/cmdline by testing env_end for
zero. It is, apparently, intentionally set last in create_*_tables().
This bug was found by the PaX size_overflow plugin that detected the
arithmetic underflow of 'this_len = env_end - (env_start + src)' when
env_end is still zero.
The expected consequence is that userland trying to access
/proc/<PID>/environ of a not yet fully set up process may get
inconsistent data as we're in the middle of copying in the environment
variables.
Fixes: https://forums.grsecurity.net/viewtopic.php?f=3&t=4363
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=116461
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Emese Revfy <re.emese@gmail.com>
Cc: Pax Team <pageexec@freemail.hu>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Mateusz Guzik <mguzik@redhat.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6984ab1ab3 upstream.
A wrong decoding of the touch coordinate message causes a wrong touch
ID. Touch ID for dual touch must be 0 or 1.
According to the actual Neonode nine byte touch coordinate coding,
the state is transported in the lower nibble and the touch ID in
the higher nibble of payload byte five.
Signed-off-by: Knut Wohlrab <Knut.Wohlrab@de.bosch.com>
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 567a44ecb4 upstream.
Needed for v2 of the device firmware, otherwise kernel will stuck for few
seconds and throw "usb_submit_urb(ctrl) failed: -1" early on system boot.
Signed-off-by: Nazar Mokrynskyi <nazar@mokrynskyi.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 27e0e63853 upstream.
The copying of ring data was wrong for two cases: For a full ring
nothing got copied at all (as in that case the canonicalized producer
and consumer indexes are identical). And in case one or both of the
canonicalized (after the resize) indexes would point into the second
half of the buffer, the copied data ended up in the wrong (free) part
of the new buffer. In both cases uninitialized data would get passed
back to the caller.
Fix this by simply copying the old ring contents twice: Once to the
low half of the new buffer, and a second time to the high half.
This addresses the inability to boot a HVM guest with 64 or more
vCPUs. This regression was caused by 8620015499 (xen/evtchn:
dynamically grow pending event channel ring).
Reported-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dfd74a1edf upstream.
Commit 55b3da98a4 (xen/balloon: find
non-conflicting regions to place hotplugged memory) caused a
regression in 4.4.
When ballooning on an x86 32 bit PAE system with close to 64 GiB of
memory, the address returned by allocate_resource may be above 64 GiB.
When using CONFIG_SPARSEMEM, this setup is limited to using physical
addresses < 64 GiB. When adding memory at this address, it runs off
the end of the mem_section array and causes a crash. Instead, fail
the ballooning request.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 60901df3ae upstream.
Commit 1084b1988d (xen: Add Xen specific
page definition) caused a regression in 4.4.
The xen functions to convert between pages and pfns fail due to an
overflow on systems where a physical address may not fit in an
unsigned long (e.g. x86 32 bit PAE systems). Rework the conversion to
avoid overflow. This should also result in simpler object code.
This bug manifested itself as disk corruption with Linux 4.4 when
using blkfront in a Xen HVM x86 32 bit guest with more than 4 GiB of
memory.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a0a966b838 upstream.
We want to skip reparenting a clock on turning on power domain, if we
do not have the parent yet. The parent is obtained when turning the
domain off. However due to a typo, the loop is continued on IS_ERR() of
clock being reparented, not on the IS_ERR() of the parent.
Theoretically this could lead to OOPS on first turn on of a power
domain, if there was no turn off before. Practically that should never
happen because all power domains are turned on by default (reset value,
bootloader does not turn off them usually) so the first action will be
always turn off.
Fixes: 29e5eea06b ("ARM: EXYNOS: Get current parent clock for power domain on/off")
Reported-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit acbef7b766 upstream.
Since the wildcard at the end of OF module aliases is gone, autoloading
of modules that don't match a device's last (most generic) compatible
value fails.
For example the CODA960 VPU on i.MX6Q has the SoC specific compatible
"fsl,imx6q-vpu" and the generic compatible "cnm,coda960". Since the
driver currently only works with knowledge about the SoC specific
integration, it doesn't list "cnm,cod960" in the module device table.
This results in the device compatible
"of:NvpuT<NULL>Cfsl,imx6q-vpuCcnm,coda960" not matching the module alias
"of:N*T*Cfsl,imx6q-vpu" anymore, whereas before commit 2f632369ab
("modpost: don't add a trailing wildcard for OF module aliases") it
matched the module alias "of:N*T*Cfsl,imx6q-vpu*".
This patch adds two module aliases for each compatible, one without the
wildcard and one with "C*" appended.
$ modinfo coda | grep imx6q
alias: of:N*T*Cfsl,imx6q-vpuC*
alias: of:N*T*Cfsl,imx6q-vpu
Fixes: 2f632369ab ("modpost: don't add a trailing wildcard for OF module aliases")
Link: http://lkml.kernel.org/r/1462203339-15340-1-git-send-email-p.zabel@pengutronix.de
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ec0811d30 upstream.
When the first propgated copy was a slave the following oops would result:
> BUG: unable to handle kernel NULL pointer dereference at 0000000000000010
> IP: [<ffffffff811fba4e>] propagate_one+0xbe/0x1c0
> PGD bacd4067 PUD bac66067 PMD 0
> Oops: 0000 [#1] SMP
> Modules linked in:
> CPU: 1 PID: 824 Comm: mount Not tainted 4.6.0-rc5userns+ #1523
> Hardware name: Bochs Bochs, BIOS Bochs 01/01/2007
> task: ffff8800bb0a8000 ti: ffff8800bac3c000 task.ti: ffff8800bac3c000
> RIP: 0010:[<ffffffff811fba4e>] [<ffffffff811fba4e>] propagate_one+0xbe/0x1c0
> RSP: 0018:ffff8800bac3fd38 EFLAGS: 00010283
> RAX: 0000000000000000 RBX: ffff8800bb77ec00 RCX: 0000000000000010
> RDX: 0000000000000000 RSI: ffff8800bb58c000 RDI: ffff8800bb58c480
> RBP: ffff8800bac3fd48 R08: 0000000000000001 R09: 0000000000000000
> R10: 0000000000001ca1 R11: 0000000000001c9d R12: 0000000000000000
> R13: ffff8800ba713800 R14: ffff8800bac3fda0 R15: ffff8800bb77ec00
> FS: 00007f3c0cd9b7e0(0000) GS:ffff8800bfb00000(0000) knlGS:0000000000000000
> CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
> CR2: 0000000000000010 CR3: 00000000bb79d000 CR4: 00000000000006e0
> Stack:
> ffff8800bb77ec00 0000000000000000 ffff8800bac3fd88 ffffffff811fbf85
> ffff8800bac3fd98 ffff8800bb77f080 ffff8800ba713800 ffff8800bb262b40
> 0000000000000000 0000000000000000 ffff8800bac3fdd8 ffffffff811f1da0
> Call Trace:
> [<ffffffff811fbf85>] propagate_mnt+0x105/0x140
> [<ffffffff811f1da0>] attach_recursive_mnt+0x120/0x1e0
> [<ffffffff811f1ec3>] graft_tree+0x63/0x70
> [<ffffffff811f1f6b>] do_add_mount+0x9b/0x100
> [<ffffffff811f2c1a>] do_mount+0x2aa/0xdf0
> [<ffffffff8117efbe>] ? strndup_user+0x4e/0x70
> [<ffffffff811f3a45>] SyS_mount+0x75/0xc0
> [<ffffffff8100242b>] do_syscall_64+0x4b/0xa0
> [<ffffffff81988f3c>] entry_SYSCALL64_slow_path+0x25/0x25
> Code: 00 00 75 ec 48 89 0d 02 22 22 01 8b 89 10 01 00 00 48 89 05 fd 21 22 01 39 8e 10 01 00 00 0f 84 e0 00 00 00 48 8b 80 d8 00 00 00 <48> 8b 50 10 48 89 05 df 21 22 01 48 89 15 d0 21 22 01 8b 53 30
> RIP [<ffffffff811fba4e>] propagate_one+0xbe/0x1c0
> RSP <ffff8800bac3fd38>
> CR2: 0000000000000010
> ---[ end trace 2725ecd95164f217 ]---
This oops happens with the namespace_sem held and can be triggered by
non-root users. An all around not pleasant experience.
To avoid this scenario when finding the appropriate source mount to
copy stop the walk up the mnt_master chain when the first source mount
is encountered.
Further rewrite the walk up the last_source mnt_master chain so that
it is clear what is going on.
The reason why the first source mount is special is that it it's
mnt_parent is not a mount in the dest_mnt propagation tree, and as
such termination conditions based up on the dest_mnt mount propgation
tree do not make sense.
To avoid other kinds of confusion last_dest is not changed when
computing last_source. last_dest is only used once in propagate_one
and that is above the point of the code being modified, so changing
the global variable is meaningless and confusing.
fixes: f2ebb3a921 ("smarter propagate_mnt()")
Reported-by: Tycho Andersen <tycho.andersen@canonical.com>
Reviewed-by: Seth Forshee <seth.forshee@canonical.com>
Tested-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 32a4e16903 upstream.
Instead of using "zswap" as the name for all zpools created, add an
atomic counter and use "zswap%x" with the counter number for each zpool
created, to provide a unique name for each new zpool.
As zsmalloc, one of the zpool implementations, requires/expects a unique
name for each pool created, zswap should provide a unique name. The
zsmalloc pool creation does not fail if a new pool with a conflicting
name is created, unless CONFIG_ZSMALLOC_STAT is enabled; in that case,
zsmalloc pool creation fails with -ENOMEM. Then zswap will be unable to
change its compressor parameter if its zpool is zsmalloc; it also will
be unable to change its zpool parameter back to zsmalloc, if it has any
existing old zpool using zsmalloc with page(s) in it. Attempts to
change the parameters will result in failure to create the zpool. This
changes zswap to provide a unique name for each zpool creation.
Fixes: f1c54846ee ("zswap: dynamic pool creation")
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Reported-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Dan Streetman <dan.streetman@canonical.com>
Cc: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 14af4a5e9b upstream.
/proc/sys/vm/stat_refresh warns nr_isolated_anon and nr_isolated_file go
increasingly negative under compaction: which would add delay when
should be none, or no delay when should delay. The bug in compaction
was due to a recent mmotm patch, but much older instance of the bug was
also noticed in isolate_migratepages_range() which is used for CMA and
gigantic hugepage allocations.
The bug is caused by putback_movable_pages() in an error path
decrementing the isolated counters without them being previously
incremented by acct_isolated(). Fix isolate_migratepages_range() by
removing the error-path putback, thus reaching acct_isolated() with
migratepages still isolated, and leaving putback to caller like most
other places do.
Fixes: edc2ca6124 ("mm, compaction: move pageblock checks up from isolate_migratepages_range()")
[vbabka@suse.cz: expanded the changelog]
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Michal Hocko <mhocko@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4550c4e157 upstream.
Cgroup2 currently doesn't have a per-cgroup swappiness setting. We
might want to add one later - that's a different discussion - but until
we do, the cgroups should always follow the system setting. Otherwise
it will be unchangeably set to whatever the ancestor inherited from the
system setting at the time of cgroup creation.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 689de1d6ca upstream.
This is a fairly minimal fixup to the horribly bad behavior of hash_64()
with certain input patterns.
In particular, because the multiplicative value used for the 64-bit hash
was intentionally bit-sparse (so that the multiply could be done with
shifts and adds on architectures without hardware multipliers), some
bits did not get spread out very much. In particular, certain fairly
common bit ranges in the input (roughly bits 12-20: commonly with the
most information in them when you hash things like byte offsets in files
or memory that have block factors that mean that the low bits are often
zero) would not necessarily show up much in the result.
There's a bigger patch-series brewing to fix up things more completely,
but this is the fairly minimal fix for the 64-bit hashing problem. It
simply picks a much better constant multiplier, spreading the bits out a
lot better.
NOTE! For 32-bit architectures, the bad old hash_64() remains the same
for now, since 64-bit multiplies are expensive. The bigger hashing
cleanup will replace the 32-bit case with something better.
The new constants were picked by George Spelvin who wrote that bigger
cleanup series. I just picked out the constants and part of the comment
from that series.
Cc: George Spelvin <linux@horizon.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9c573de328 upstream.
blk_queue_split marks bio unmergeable, which makes sense for normal bio.
But if dispatching the bio to underlayer disk, the blk_queue_split
checks are invalid, hence it's possible the bio becomes mergeable.
In the reported bug, this bug causes trim against raid0 performance slash
https://bugzilla.kernel.org/show_bug.cgi?id=117051
Reported-and-tested-by: Park Ju Hyung <qkrwngud825@gmail.com>
Fixes: 6ac45aeb6bca(block: avoid to merge splitted bio)
Cc: Ming Lei <ming.lei@canonical.com>
Cc: Neil Brown <neilb@suse.de>
Reviewed-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 854145e0a8 upstream.
Currently register functions for events will be called
through the 'reg' field of event class directly without
any check when seting up triggers.
Triggers for events that don't support register through
debug fs (events under events/ftrace are for trace-cmd to
read event format, and most of them don't have a register
function except events/ftrace/functionx) can't be enabled
at all, and an oops will be hit when setting up trigger
for those events, so just not creating them is an easy way
to avoid the oops.
Link: http://lkml.kernel.org/r/1462275274-3911-1-git-send-email-chuhu@redhat.com
Fixes: 85f2b08268 ("tracing: Add basic event trigger framework")
Signed-off-by: Chunyu Hu <chuhu@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e6436be21e upstream.
In the case that dev_alloc_name() fails, e.g. because the name was
given by the user and already exists, we need to clean up properly
and free the per-CPU statistics. Fix that.
Fixes: 5a490510ba ("mac80211: use per-CPU TX/RX statistics")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit de478a6138 upstream.
by moving common code to ar5008_hw_cmn_spur_mitigate i forgot to move
mask_m & mask_p initialisation. This coused a performance regression
on ar9281.
Fixes: f911085ffa ("ath9k: split ar5008_hw_spur_mitigate and reuse common code in ar9002_hw_spur_mitigate.")
Reported-by: Gustav Frederiksen <lkml2017@openmailbox.org>
Tested-by: Gustav Frederiksen <lkml2017@openmailbox.org>
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aeb6641f8e upstream.
gcc-6 complains about the indentation of the lpfc_destroy_vport_work_array()
call in lpfc_online(), which clearly doesn't look right:
drivers/scsi/lpfc/lpfc_init.c: In function 'lpfc_online':
drivers/scsi/lpfc/lpfc_init.c:2880:3: warning: statement is indented as if it were guarded by... [-Wmisleading-indentation]
lpfc_destroy_vport_work_array(phba, vports);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/lpfc/lpfc_init.c:2863:2: note: ...this 'if' clause, but it is not
if (vports != NULL)
^~
Looking at the patch that introduced this code, it's clear that the
behavior is correct and the indentation is wrong.
This fixes the indentation and adds curly braces around the previous
if() block for clarity, as that is most likely what caused the code
to be misindented in the first place.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 549e55cd2a ("[SCSI] lpfc 8.2.2 : Fix locking around HBA's port_list")
Reviewed-by: Sebastian Herbszt <herbszt@gmx.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b0883f338 upstream.
When converting period and duty_cycle from nanoseconds to fclk cycles,
the error introduced by the integer division can be appreciable, especially
in the case of slow fclk or short period. Use DIV_ROUND_CLOSEST_ULL() so
that the error is kept to +/- 0.5 clock cycles.
Fixes: 6604c6556d ("pwm: Add PWM driver for OMAP using dual-mode timers")
Signed-off-by: David Rivshin <drivshin@allworx.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd37888142 upstream.
Add sanity checking to ensure that we do not program load or match values
that are out of range if a user requests period or duty_cycle values which
are not achievable. The match value cannot be less than the load value (but
can be equal), and neither can be 0xffffffff. This means that there must be
at least one fclk cycle between load and match, and another between match
and overflow.
Fixes: 6604c6556d ("pwm: Add PWM driver for OMAP using dual-mode timers")
Signed-off-by: David Rivshin <drivshin@allworx.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
[thierry.reding@gmail.com: minor coding style cleanups]
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f8caa79226 upstream.
Fix the calculation of load_value and match_value. Currently they
are slightly too low, which produces a noticeably wrong PWM rate with
sufficiently short periods (i.e. when 1/period approaches clk_rate/2).
Example:
clk_rate=32768Hz, period=122070ns, duty_cycle=61035ns (8192Hz/50% PWM)
Correct values: load = 0xfffffffc, match = 0xfffffffd
Current values: load = 0xfffffffa, match = 0xfffffffc
effective PWM: period=183105ns, duty_cycle=91553ns (5461Hz/50% PWM)
Fixes: 6604c6556d ("pwm: Add PWM driver for OMAP using dual-mode timers")
Signed-off-by: David Rivshin <drivshin@allworx.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4d3ac66624 upstream.
The change fixes potential oops while accessing iomem on invalid
address, if devm_ioremap_resource() fails due to some reason.
The devm_ioremap_resource() function returns ERR_PTR() and never
returns NULL, which makes useless a following check for NULL.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Fixes: 5e63dcc74b ("clk: bcm2835: Add a driver for the auxiliary peripheral clock gates")
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f4c7a138d upstream.
In the initial fix for non-zero divider shift value, the parenthesis
was missing after the negate operation. This patch adds the required
parenthesis. Otherwise, lower bits may be cleared unintentionally.
Signed-off-by: Loc Ho <lho@apm.com>
Acked-by: Toan Le <toanle@apm.com>
Fixes: 1382ea631d ("clk: xgene: Fix divider with non-zero shift value")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 33f60d0260 upstream.
The APB0 clock on A23 is a zero-based divider, not a power-of-two based
divider.
Note that this patch does not apply cleanly to kernels before 4.5-rc1,
which added CLK_OF_DECLARE support to this driver.
Fixes: 57a1fbf284 ("clk: sunxi: Add A23 APB0 divider clock support")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ec7957a6aa upstream.
Despite care take to allocate clocks state containers the
SP810 driver actually just supports creating one instance:
all clocks registered for every instance will end up with the
exact same name and __clk_init() will fail.
Rename the timclken<0> .. timclken<n> to sp810_<instance>_<n>
so every clock on every instance gets a unique name.
This is necessary for the RealView PBA8 which has two SP810
blocks: the second block will not register its clocks unless
every clock on every instance is unique and results in boot
logs like this:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at ../drivers/clk/versatile/clk-sp810.c:137
clk_sp810_of_setup+0x110/0x154()
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted
4.5.0-rc2-00030-g352718fc39f6-dirty #225
Hardware name: ARM RealView Machine (Device Tree Support)
[<c00167f8>] (unwind_backtrace) from [<c0013204>]
(show_stack+0x10/0x14)
[<c0013204>] (show_stack) from [<c01a049c>]
(dump_stack+0x84/0x9c)
[<c01a049c>] (dump_stack) from [<c0024990>]
(warn_slowpath_common+0x74/0xb0)
[<c0024990>] (warn_slowpath_common) from [<c0024a68>]
(warn_slowpath_null+0x1c/0x24)
[<c0024a68>] (warn_slowpath_null) from [<c051eb44>]
(clk_sp810_of_setup+0x110/0x154)
[<c051eb44>] (clk_sp810_of_setup) from [<c051e3a4>]
(of_clk_init+0x12c/0x1c8)
[<c051e3a4>] (of_clk_init) from [<c0504714>]
(time_init+0x20/0x2c)
[<c0504714>] (time_init) from [<c0501b18>]
(start_kernel+0x244/0x3c4)
[<c0501b18>] (start_kernel) from [<7000807c>] (0x7000807c)
---[ end trace cb88537fdc8fa200 ]---
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Fixes: 6e973d2c43 "clk: vexpress: Add separate SP810 driver"
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb473593c8 upstream.
As preparation for arm64 based mesongxbb, which pulls in this code once
enabling ARCH_MESON, fix a size_t vs. unsigned int type mismatch.
The loop uses a local unsigned int variable, so adopt that type,
matching the header.
Fixes: 7a29a86943 ("clk: meson: Add support for Meson clock controller")
Signed-off-by: Andreas Färber <afaerber@suse.de>
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d961f11a1 upstream.
If we fail to probe the driver, we should not directly break
from the for_each_available_child_of_node since it calls of_node_get
while iterating. This patch add of_node_put to fix the unbalanced
call pair.
Fixes: 7c696693a4 ("soc: rockchip: power-domain: Add power domain driver")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5035981979 upstream.
Commit e6d5e7d90b ("clk-divider: Fix READ_ONLY when divider > 1") removed
the special ops struct for read-only clocks and instead opted to handle
them inside the regular ops.
On the rk3368 this results in breakage as aclkm now gets set a value.
While it is the same divider value, the A53 core still doesn't like it,
which can result in the cpu ending up in a hang.
The reason being that "ACLKENMasserts one clock cycle before the rising
edge of ACLKM" and the clock should only be touched when STANDBYWFIL2
is asserted.
To fix this, reintroduce the read-only ops but do include the round_rate
callback. That way no writes that may be unsafe are done to the divider
register in any case.
The Rockchip use of the clk_divider_ops is adapted to this split again,
as is the nxp, lpc18xx-ccu driver that was included since the original
commit. On lpc18xx-ccu the divider seems to always be read-only
so only uses the new ops now.
Fixes: e6d5e7d90b ("clk-divider: Fix READ_ONLY when divider > 1")
Reported-by: Zhang Qing <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a6139b6271 upstream.
This patch corrects the error case in association path by returning
-1. Earlier "media_connected" used to remain on in this error case
causing failure for further association attempts.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Fixes: b887664d88 ('mwifiex: channel switch handling for station')
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 53a5c9bc53 upstream.
Currently, we are providing wrong payload data of pktlog to trace points.
Data we receive from FW through copy engine 8 contains pktlog data alone.
We don't need to parse anything in driver before handing it to trace
points.
Fixes: afb0bf7f53 ("ath10k: add support for pktlog in QCA99X0")
Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8134233e8d upstream.
If the call to acpi_get_object_info() fails then "info" hasn't been
initialized. In that situation, we already know that "version" should
be XGENE_AHCI_V1 so we don't actually need to dereference "info".
Fixes: c9802a4be6 ('ata: ahci_xgene: Add AHCI Support for 2nd HW version of APM X-Gene SoC AHCI SATA Host controller.')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3681c85dff upstream.
After register null_blk devices into lightnvm, we forget
to add these devices to the the nullb_list, makes them
invisible to the null_blk driver.
Signed-off-by: Wenwei Tao <ww.tao0320@gmail.com>
Fixes: a514379b0c ("null_blk: oops when initializing without lightnvm")
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6adb03de40 upstream.
When an I/O finishes, full blocks are moved from the open to the closed
list - a lock is taken to protect the list. This happens at the moment
in the interrupt context, which is not correct.
This patch moves this logic to the block workqueue instead, avoiding
holding a spinlock without interrupt save in an interrupt context.
Signed-off-by: Javier González <javier@cnexlabs.com>
Fixes: ff0e498bfa ("lightnvm: manage open and closed blocks sepa...")
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit da6ccaaa79 upstream.
Make the "Attempted send on closed socket" error messages generated in
nbd_request_handler() ratelimited.
When the nbd socket is shutdown, the nbd_request_handler() function emits
an error message for every request remaining in its queue. If the queue
is large, this will spam a large amount of messages to the log. There's
no need for a separate error message for each request, so this patch
ratelimits it.
In the specific case this was found, the system was virtual and the error
messages were logged to the serial port, which overwhelmed it.
Fixes: 4d48a542b4 ("nbd: fix I/O hang on disconnected nbds")
Signed-off-by: Dan Streetman <dan.streetman@canonical.com>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 73fb270592 upstream.
Smatch reports the following warning:
CHECK drivers/net/wireless/realtek/rtlwifi/rc.c
drivers/net/wireless/realtek/rtlwifi/rc.c:144 _rtl_rc_rate_set_series() warn: impossible condition '(wireless_mode == 256) => (0-255 == 256)'
This warning arises because commit acc6907b87a9 ("rtlwifi: Fix warning
from ieee80211_get_tx_rates() when using 5G") now checks the wireless
mode for WIRELESS_MODE_AC_ONLY (BIT(8)) in _rtl_rc_rate_set_series().
As a result, all quantities used to store the wireless mode must be u16.
This patch also reorders struct rtl_sta_info to save a little space.
Fixes: d76d65fd26 ("rtlwifi: fix broken VHT support")
Reported-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f719e3754e upstream.
Jiri Bohac is reporting for a problem where the attempt
to reschedule existing connection to another real server
needs proper redirect for the conntrack used by the IPVS
connection. For example, when IPVS connection is created
to NAT-ed real server we alter the reply direction of
conntrack. If we later decide to select different real
server we can not alter again the conntrack. And if we
expire the old connection, the new connection is left
without conntrack.
So, the only way to redirect both the IPVS connection and
the Netfilter's conntrack is to drop the SYN packet that
hits existing connection, to wait for the next jiffie
to expire the old connection and its conntrack and to rely
on client's retransmission to create new connection as
usually.
Jiri Bohac provided a fix that drops all SYNs on rescheduling,
I extended his patch to do such drops only for connections
that use conntrack. Here is the original report from Jiri Bohac:
Since commit dc7b3eb900 ("ipvs: Fix reuse connection if real server
is dead"), new connections to dead servers are redistributed
immediately to new servers. The old connection is expired using
ip_vs_conn_expire_now() which sets the connection timer to expire
immediately.
However, before the timer callback, ip_vs_conn_expire(), is run
to clean the connection's conntrack entry, the new redistributed
connection may already be established and its conntrack removed
instead.
Fix this by dropping the first packet of the new connection
instead, like we do when the destination server is not available.
The timer will have deleted the old conntrack entry long before
the first packet of the new connection is retransmitted.
Fixes: dc7b3eb900 ("ipvs: Fix reuse connection if real server is dead")
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7617a24f83 upstream.
The IPVS SIP persistence engine is not able to parse the SIP header
"Call-ID" when such header is inserted in the first positions of
the SIP message.
When IPVS is configured with "--pe sip" option, like for example:
ipvsadm -A -u 1.2.3.4:5060 -s rr --pe sip -p 120 -o
some particular messages (see below for details) do not create entries
in the connection template table, which can be listed with:
ipvsadm -Lcn --persistent-conn
Problematic SIP messages are SIP responses having "Call-ID" header
positioned just after message first line:
SIP/2.0 200 OK
[Call-ID header here]
[rest of the headers]
When "Call-ID" header is positioned down (after a few other headers)
it is correctly recognized.
This is due to the data offset used in get_callid function call inside
ip_vs_pe_sip.c file: since dptr already points to the start of the
SIP message, the value of dataoff should be initially 0.
Otherwise the header is searched starting from some bytes after the
first character of the SIP message.
Fixes: 758ff03387 ("IPVS: sip persistence engine")
Signed-off-by: Marco Angaroni <marcoangaroni@gmail.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f20efba41 upstream.
ip_vs_fill_iph_skb_off() may not find an IP header, and gcc has
determined that ip_vs_sip_fill_param() then incorrectly accesses
the protocol fields:
net/netfilter/ipvs/ip_vs_pe_sip.c: In function 'ip_vs_sip_fill_param':
net/netfilter/ipvs/ip_vs_pe_sip.c:76:5: error: 'iph.protocol' may be used uninitialized in this function [-Werror=maybe-uninitialized]
if (iph.protocol != IPPROTO_UDP)
^
net/netfilter/ipvs/ip_vs_pe_sip.c:81:10: error: 'iph.len' may be used uninitialized in this function [-Werror=maybe-uninitialized]
dataoff = iph.len + sizeof(struct udphdr);
^
This adds a check for the ip_vs_fill_iph_skb_off() return code
before looking at the ip header data returned from it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: b0e010c527 ("ipvs: replace ip_vs_fill_ip4hdr with ip_vs_fill_iph_skb_off")
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 16eeed7e55 upstream.
Commit 0881841f7e introduced a regression by inverting a test check
after calling clocksource_mmio_init(). That results on the system to
hang at boot time.
Fix it by inverting the test again.
Fixes: 0881841f7e ("Replace code by clocksource_mmio_init")
Reported-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c283e41ef3 upstream.
The DMA chip has a fixed number of requestor lines used for flow
control. This number is platform dependent. The pxa_dma dma driver will
use this value to activate or not the flow control.
There won't be any impact on mmp_pdma driver.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c4924e9244 upstream.
The info->status[] array has 3 elements. We are using size
MAX77843_MUIC_IRQ_NUM (16) instead of MAX77843_MUIC_STATUS_NUM (3) as
intended.
Fixes: 135d9f7d13 ('extcon: max77843: Clear IRQ bits state before request IRQ')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Jaewon Kim <jaewon02.kim@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[cw00.choi: Modify the patch title]
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 042d4460b5 upstream.
The newly added STM code uses SRCU, but does not ensure that
this code is part of the kernel:
drivers/built-in.o: In function `stm_source_link_show':
include/linux/srcu.h:221: undefined reference to `__srcu_read_lock'
include/linux/srcu.h:238: undefined reference to `__srcu_read_unlock'
drivers/built-in.o: In function `stm_source_link_drop':
include/linux/srcu.h:221: undefined reference to `__srcu_read_lock'
include/linux/srcu.h:238: undefined reference to `__srcu_read_unlock'
This adds a Kconfig 'select' statement like all the other SRCU using
drivers have.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 7bd1d4093c ("stm class: Introduce an abstraction for System Trace Module devices")
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c0b5eed110 upstream.
It's better to set the continueSession attribute for the unseal
operation so that the session object is not removed as a side-effect
when the operation is successful. Since a user process created the
session, it should be also decide when the session is destroyed.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Fixes: 5beb0c435b ("keys, trusted: seal with a TPM2 authorization policy")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f3c82ade7c upstream.
In my original patch sealing with policy was done with dynamically
allocated buffer that I changed later into an array so the checks in
tpm2-cmd.c became invalid. This patch fixes the issue.
Fixes: 5beb0c435b ("keys, trusted: seal with a TPM2 authorization policy")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3deb9438d3 upstream.
gcc-6 found a dubious indentation in the megasas_mgmt_fw_ioctl
function:
drivers/scsi/megaraid/megaraid_sas_base.c: In function 'megasas_mgmt_fw_ioctl':
drivers/scsi/megaraid/megaraid_sas_base.c:6658:4: warning: statement is indented as if it were guarded by... [-Wmisleading-indentation]
kbuff_arr[i] = NULL;
^~~~~~~~~
drivers/scsi/megaraid/megaraid_sas_base.c:6653:3: note: ...this 'if' clause, but it is not
if (kbuff_arr[i])
^~
The code is actually correct, as there is no downside in clearing a NULL
pointer again.
This clarifies the code and avoids the warning by adding extra curly
braces.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 90dc9d98f0 ("megaraid_sas : MFI MPT linked list corruption fix")
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a6ab1e8126 upstream.
sunrpc_cache_pipe_upcall() can detect a race if CACHE_PENDING is no longer
set. In this case it aborts the queuing of the upcall.
However it has already taken a new counted reference on "h" and
doesn't "put" it, even though it frees the data structure holding the reference.
So let's delay the "cache_get" until we know we need it.
Fixes: f9e1aedc6c ("sunrpc/cache: remove races with queuing an upcall.")
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 43b4eb9fe7 upstream.
As the Dan report the smatch check the thermal driver warning:
drivers/thermal/rockchip_thermal.c:551 rockchip_configure_from_dt()
warn: impossible condition '(thermal->tshut_temp > ((~0 >> 1))) =>
(s32min-s32max > s32max)'
Although The shut_temp read from DT is u32,the temperature is currently
represented as int not long in the thermal driver.
Let's change to make shut_temp instead of the thermal->tshut_temp for
the condition.
Fixes: commit 437df2172e
("thermal: rockchip: consistently use int for temperatures")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b87b70c53 upstream.
Prior to 3.13 make allmodconfig KCONFIG_ALLCONFIG=/dev/null used
to be equivalent to make allmodconfig; these days it hardwires MODULES to n.
In fact, any KCONFIG_ALLCONFIG that doesn't set MODULES explicitly is
treated as if it set it to n.
Regression had been introduced by commit cfa98f ("kconfig: do not
override symbols already set"); what happens is that conf_read_simple()
does sym_calc_value(modules_sym) on exit, which leaves SYMBOL_VALID set and
has conf_set_all_new_symbols() skip modules_sym.
It's pretty easy to fix - simply move that call of sym_calc_value()
into the callers, except for the ones in KCONFIG_ALLCONFIG handling.
Objections?
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Fixes: cfa98f2e0a ("kconfig: do not override symbols already set")
Signed-off-by: Michal Marek <mmarek@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 838fe18877 upstream.
cleaner_kthread() is not marked freezable, and therefore calling
try_to_freeze() in its context is a pointless no-op.
In addition to that, as has been clearly demonstrated by 80ad623edd
("Revert "btrfs: clear PF_NOFREEZE in cleaner_kthread()"), it's perfectly
valid / legal for cleaner_kthread() to stay scheduled out in an arbitrary
place during suspend (in that particular example that was waiting for
reading of extent pages), so there is no need to leave any traces of
freezer in this kthread.
Fixes: 80ad623edd ("Revert "btrfs: clear PF_NOFREEZE in cleaner_kthread()")
Fixes: 6962491321 ("btrfs: clear PF_NOFREEZE in cleaner_kthread()")
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 33b96d2c95 upstream.
Currently we have an incorrect behaviour when multiple devices
are present under the weim node. For example:
&weim {
...
status = "okay";
sram@0,0 {
...
status = "okay";
};
mram@0,0 {
...
status = "disabled";
};
};
In this case only the 'sram' device should be probed and not 'mram'.
However what happens currently is that the status variable is ignored,
causing the 'sram' device to be disabled and 'mram' to be enabled.
Change the weim_parse_dt() function to use
for_each_available_child_of_node()so that the devices marked with
'status = disabled' are not probed.
Suggested-by: Wolfgang Netbal <wolfgang.netbal@sigmatek.at>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 883cbc901b upstream.
This patch updates the GPMC's DT DMA property to reflect the updated eDMA
bindings.
Fixes: cce1ee0001 ("ARM: DTS: am437x: Use the new DT bindings for the eDMA3")
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a2abf904a6 upstream.
This patch updates the GPMC's DT DMA property to reflect the updated eDMA
bindings.
Fixes: b5e5090660 ("ARM: DTS: am33xx: Use the new DT bindings for the eDMA3")
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07c6b2d01d upstream.
Since the switch from mmp_pdma to pxa_dma driver for pxa architectures,
the pxa_dma requires 2 arguments, namely the requestor line and the
requested priority.
Fix the only left device node which was still passing only one argument,
making the pxa3xx-nand driver misbehave in a device-tree configuration,
ie. failing all data transfers.
Fixes: c943646d1f ("ARM: dts: pxa: add dma engine node to pxa3xx-nand")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b3a7f31eb7 upstream.
The Armada 375 has the same SATA IP as Armada 370 and Armada XP, which
requires the PHY speed to be set in the LP_PHY_CTL register for SATA
hotplug to work.
Therefore, this commit updates the compatible string used to describe
the SATA IP in Armada 375 from marvell,orion-sata to
marvell,armada-370-sata.
Fixes: 4de5908509 ("ARM: mvebu: add Device Tree description of the Armada 375 SoC")
Signed-off-by: Lior Amsalem <alior@marvell.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc7eb9d589 upstream.
We cannot select a symbol that has disabled dependencies, so
we get a warning if we ever enable EXYNOS_THERMAL without
also turning on THERMAL_OF:
warning: (ARCH_EXYNOS) selects EXYNOS_THERMAL which has unmet direct dependencies (THERMAL && (ARCH_EXYNOS || COMPILE_TEST) && THERMAL_OF)
This adds another 'select' in the platform code to avoid that
case. Alternatively, we could decide to not select EXYNOS_THERMAL
here and instead make it a user option.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: f87e6bd3f7 ("thermal: exynos: Add the dependency of CONFIG_THERMAL_OF instead of CONFIG_OF")
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef2b1d777d upstream.
The atlas7 clock controller driver registers a reset controller
for itself, which causes a link error when the subsystem is
disabled:
drivers/built-in.o: In function `atlas7_clk_init':
drivers/clk/sirf/clk-atlas7.c:1681: undefined reference to `reset_controller_register'
As the clk driver does not have a Kconfig symbol for itself
but it always built-in when the platform is enabled, we have
to ensure that the reset controller subsystem is also built-in
in this case.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Fixes: 301c5d2940 ("clk: sirf: add CSR atlas7 clk and reset support")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 98f4222150 upstream.
Based on CPU type choose generic omap3 or omap3430 specific cpuidle
parameters. Parameters for omap3430 were measured on Nokia N900 device and
added by commit 5a1b1d3a9e ("OMAP3: RX-51: Pass cpu idle parameters")
which were later removed by commit 231900afba ("ARM: OMAP3: cpuidle -
remove rx51 cpuidle parameters table") due to huge code complexity.
This patch brings cpuidle parameters for omap3430 devices again, but uses
simple condition based on CPU type.
Fixes: 231900afba ("ARM: OMAP3: cpuidle - remove rx51 cpuidle
parameters table")
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9098903555 upstream.
The 4b3a321223 ("perf hists browser: Support flat callchains") commit
over-aggressively tried to optimize callchain_node__init_have_children().
That lead to --tui mode not allowing to expand call chain elements if a
call chain element had only one parent. That's why --inverted callgraphs
looked halfway sane, but plain ones didn't.
Revert that individual optimization, it wasn't really related to the
rest of the commit.
Signed-off-by: Andres Freund <andres@anarazel.de>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Fixes: 4b3a321223 ("perf hists browser: Support flat callchains")
Link: http://lkml.kernel.org/r/20160330190245.GB13305@awork2.anarazel.de
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8fdc65391c upstream.
Stephane reported that commit:
3cbaa59069 ("perf: Fix ctx time tracking by introducing EVENT_TIME")
introduced a regression wrt. time tracking, as easily observed by:
> This patch introduce a bug in the time tracking of events when
> multiplexing is used.
>
> The issue is easily reproducible with the following perf run:
>
> $ perf stat -a -C 0 -e branches,branches,branches,branches,branches,branches -I 1000
> 1.000730239 652,394 branches (66.41%)
> 1.000730239 597,809 branches (66.41%)
> 1.000730239 593,870 branches (66.63%)
> 1.000730239 651,440 branches (67.03%)
> 1.000730239 656,725 branches (66.96%)
> 1.000730239 <not counted> branches
>
> One branches event is shown as not having run. Yet, with
> multiplexing, all events should run especially with a 1s (-I 1000)
> interval. The delta for time_running comes out to 0. Yet, the event
> has run because the kernel is actually multiplexing the events. The
> problem is that the time tracking is the kernel and especially in
> ctx_sched_out() is wrong now.
>
> The problem is that in case that the kernel enters ctx_sched_out() with the
> following state:
> ctx->is_active=0x7 event_type=0x1
> Call Trace:
> [<ffffffff813ddd41>] dump_stack+0x63/0x82
> [<ffffffff81182bdc>] ctx_sched_out+0x2bc/0x2d0
> [<ffffffff81183896>] perf_mux_hrtimer_handler+0xf6/0x2c0
> [<ffffffff811837a0>] ? __perf_install_in_context+0x130/0x130
> [<ffffffff810f5818>] __hrtimer_run_queues+0xf8/0x2f0
> [<ffffffff810f6097>] hrtimer_interrupt+0xb7/0x1d0
> [<ffffffff810509a8>] local_apic_timer_interrupt+0x38/0x60
> [<ffffffff8175ca9d>] smp_apic_timer_interrupt+0x3d/0x50
> [<ffffffff8175ac7c>] apic_timer_interrupt+0x8c/0xa0
>
> In that case, the test:
> if (is_active & EVENT_TIME)
>
> will be false and the time will not be updated. Time must always be updated on
> sched out.
Fix this by always updating time if EVENT_TIME was set, as opposed to
only updating time when EVENT_TIME changed.
Reported-by: Stephane Eranian <eranian@google.com>
Tested-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: kan.liang@intel.com
Cc: namhyung@kernel.org
Fixes: 3cbaa59069 ("perf: Fix ctx time tracking by introducing EVENT_TIME")
Link: http://lkml.kernel.org/r/20160329072644.GB3408@twins.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f1b50c3e3 upstream.
Kernel zero day testing warned about address space confusion. A virtual
iomem address was used where a physical address is expected. The
offending functions implement an optional part of the api, so they are
removed. They can be added later, after testing.
Fixes: a1b3695820
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Acked-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1985a88107 upstream.
The ntb driver assigns between pointers an __iomem tokens, and
also casts them to 64-bit integers, which results in compiler
warnings on 32-bit systems:
drivers/ntb/test/ntb_perf.c: In function 'perf_copy':
drivers/ntb/test/ntb_perf.c:213:10: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
vbase = (u64)(u64 *)mw->vbase;
^
drivers/ntb/test/ntb_perf.c:214:14: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
dst_vaddr = (u64)(u64 *)dst;
^
This adds __iomem annotations where needed and changes the temporary
variables to iomem pointers to avoid casting them to u64. I did not
see the problem in linux-next earlier, but it show showed up in
4.5-rc1.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Fixes: 8a7b6a778a ("ntb: ntb perf tool")
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 20c07a5bf0 upstream.
Since commit 807f16d4db ("mtd: core: set some defaults
when dev.parent is set"), it's now legal for drivers
to call nand_scan and nand_scan_ident without setting
mtd.owner.
Drop the check and while at it remove the BUG() abuse.
Fixes: 807f16d4db ("mtd: core: set some defaults when dev.parent is set")
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Brian: editorial note - while commit 807f16d4db wasn't explicitly
broken, some follow-up commits in the v4.4 release broke a few
drivers, since they would hit this BUG() if they used nand_scan()
and were built as modules]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d267aefc54 upstream.
The BRCMNAND controller revision 7.1 is almost 100% compatible with the
previous v6.0 register offset layout, except for the Correctable Error
Reporting Threshold registers. Fix this by adding another table with the
correct offsets for CORR_THRESHOLD and CORR_THRESHOLD_EXT.
Fixes: 27c5b17cd1 ("mtd: nand: add NAND driver "library" for Broadcom STB NAND controller")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3b5394a3cc upstream.
This patch remove the micron_quad_enable() function which force the Quad
SPI mode. However, once this mode is enabled, the Micron memory expect ALL
commands to use the SPI 4-4-4 protocol. Hence a failure does occur when
calling spi_nor_wait_till_ready() right after the update of the Enhanced
Volatile Configuration Register (EVCR) in the micron_quad_enable() as
the SPI controller driver is not aware about the protocol change.
Since there is almost no performance increase using Fast Read 4-4-4
commands instead of Fast Read 1-1-4 commands, we rather keep on using the
Extended SPI mode than enabling the Quad SPI mode.
Let's take the example of the pretty standard use of 8 dummy cycles during
Fast Read operations on 64KB erase sectors:
Fast Read 1-1-4 requires 8 cycles for the command, then 24 cycles for the
3byte address followed by 8 dummy clock cycles and finally 65536*2 cycles
for the read data; so 131112 clock cycles.
On the other hand the Fast Read 4-4-4 would require 2 cycles for the
command, then 6 cycles for the 3byte address followed by 8 dummy clock
cycles and finally 65536*2 cycles for the read data. So 131088 clock
cycles. The theorical bandwidth increase is 0.0%.
Now using Fast Read operations on 512byte pages:
Fast Read 1-1-4 needs 8+24+8+(512*2) = 1064 clock cycles whereas Fast
Read 4-4-4 would requires 2+6+8+(512*2) = 1040 clock cycles. Hence the
theorical bandwidth increase is 2.3%.
Consecutive reads for non sequential pages is not a relevant use case so
The Quad SPI mode is not worth it.
mtd_speedtest seems to confirm these figures.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Fixes: 548cd3ab54 ("mtd: spi-nor: Add quad I/O support for Micron SPI NOR")
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ae10866864 upstream.
This patch syncs f2fs with commit abdd438b26 ("ext4 crypto: handle
unexpected lack of encryption keys") from ext4.
Fix up attempts by users to try to write to a file when they don't
have access to the encryption key.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e3ef18762f upstream.
If end_io gets an error, we don't need to set the page as dirty, since we
already set f2fs_stop_checkpoint which will not flush any data.
This will resolve the following warning.
======================================================
[ INFO: HARDIRQ-safe -> HARDIRQ-unsafe lock order detected ]
4.4.0+ #9 Tainted: G O
------------------------------------------------------
xfs_io/26773 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire:
(&(&sbi->inode_lock[i])->rlock){+.+...}, at: [<ffffffffc025483f>] update_dirty_page+0x6f/0xd0 [f2fs]
and this task is already holding:
(&(&q->__queue_lock)->rlock){-.-.-.}, at: [<ffffffff81396ea2>] blk_queue_bio+0x422/0x490
which would create a new lock dependency:
(&(&q->__queue_lock)->rlock){-.-.-.} -> (&(&sbi->inode_lock[i])->rlock){+.+...}
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fd694733d5 upstream.
This patch fixes the bug which does not cover a large section case when checking
the sanity of superblock.
If f2fs detects misalignment, it will fix the superblock during the mount time,
so it doesn't need to trigger fsck.f2fs further.
Reported-by: Matthias Prager <linux@matthiasprager.de>
Reported-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b39e9072d upstream.
read_raw_super_block was introduced to help find the
first valid superblock. Commit da554e48ca ("f2fs:
recovering broken superblock during mount") changed the
behaviour to read both of them and check whether need
the recovery flag or not. So the comment before this
function isn't consistent with what it actually does.
Also, the origin code use two tags to round the err
cases, which isn't so readable. So this patch amend
the comment and slightly reorganize it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c90e09f7fb upstream.
In the encrypted symlink case, we should check its corrupted symname after
decrypting it.
Otherwise, we can report -ENOENT incorrectly, if encrypted symname starts with
'\0'.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e1021f2b6 upstream.
ext4_reserve_inode_write() in ext4_mark_inode_dirty() could fail on
error (e.g. EIO) and iloc.bh can be NULL in this case. But the error is
ignored in the following "if" condition and ext4_expand_extra_isize()
might be called with NULL iloc.bh set, which triggers NULL pointer
dereference.
This is uncovered by commit 8b4953e13f ("ext4: reserve code points for
the project quota feature"), which enlarges the ext4_inode size, and
run the following script on new kernel but with old mke2fs:
#/bin/bash
mnt=/mnt/ext4
devname=ext4-error
dev=/dev/mapper/$devname
fsimg=/home/fs.img
trap cleanup 0 1 2 3 9 15
cleanup()
{
umount $mnt >/dev/null 2>&1
dmsetup remove $devname
losetup -d $backend_dev
rm -f $fsimg
exit 0
}
rm -f $fsimg
fallocate -l 1g $fsimg
backend_dev=`losetup -f --show $fsimg`
devsize=`blockdev --getsz $backend_dev`
good_tab="0 $devsize linear $backend_dev 0"
error_tab="0 $devsize error $backend_dev 0"
dmsetup create $devname --table "$good_tab"
mkfs -t ext4 $dev
mount -t ext4 -o errors=continue,strictatime $dev $mnt
dmsetup load $devname --table "$error_tab" && dmsetup resume $devname
echo 3 > /proc/sys/vm/drop_caches
ls -l $mnt
exit 0
[ Patch changed to simplify the function a tiny bit. -- Ted ]
Signed-off-by: Eryu Guan <guaneryu@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 616df645d7 upstream.
Remove the union in evsel so that the database id and priv pointer can
be used simultainously without conflicting and crashing.
Detailed Description for the fixed bug follows:
perf script crashes with a segmentation fault on user space tool version
4.5.rc7.ge2857b when using the python database export API. It works
properly in 4.4 and prior versions.
the crash fist appeared in:
cfc8874a48 ("perf script: Process cpu/threads maps")
How to reproduce the bug:
Remove any temporary files left over from a previous crash (if you have
already attemped to reproduce the bug):
$ rm -r test_db-perf-data
$ dropdb test_db
$ perf record timeout 1 yes >/dev/null
$ perf script -s scripts/python/export-to-postgresql.py test_db
Stack Trace:
Program received signal SIGSEGV, Segmentation fault.
__GI___libc_free (mem=0x1) at malloc.c:2929
2929 malloc.c: No such file or directory.
(gdb) bt
at util/stat.c:122
argv=<optimized out>, prefix=<optimized out>) at builtin-script.c:2231
argc=argc@entry=4, argv=argv@entry=0x7fffffffdf70) at perf.c:390
at perf.c:451
Signed-off-by: Chris Phlipot <cphlipot0@gmail.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Fixes: cfc8874a48 ("perf script: Process cpu/threads maps")
Link: http://lkml.kernel.org/r/1457500314-8912-1-git-send-email-cphlipot0@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a55e566376 upstream.
We were dropping the reference we possibly held but not obtaining one
for the new maps, which we will drop at perf_evlist__delete(), fix it.
This was caught by Steven Noonan in some of the machines which would
produce this output when caught by glibc debug mechanisms:
$ sudo perf test 21
21: Test object code reading :***
Error in `perf': corrupted double-linked list: 0x00000000023ffcd0 ***
======= Backtrace: =========
/usr/lib/libc.so.6(+0x72055)[0x7f25be0f3055]
/usr/lib/libc.so.6(+0x779b6)[0x7f25be0f89b6]
/usr/lib/libc.so.6(+0x7a0ed)[0x7f25be0fb0ed]
/usr/lib/libc.so.6(__libc_calloc+0xba)[0x7f25be0fceda]
perf(parse_events_lex_init_extra+0x38)[0x4cfff8]
perf(parse_events+0x55)[0x4a0615]
perf(perf_evlist__config+0xcf)[0x4eeb2f]
perf[0x479f82]
perf(test__code_reading+0x1e)[0x47ad4e]
perf(cmd_test+0x5dd)[0x46452d]
perf[0x47f4e3]
perf(main+0x603)[0x42c723]
/usr/lib/libc.so.6(__libc_start_main+0xf0)[0x7f25be0a1610]
perf(_start+0x29)[0x42c859]
Further investigation using valgrind led to the reference count imbalance fixed
in this patch.
Reported-and-Tested-by: Steven Noonan <steven@uplinklabs.net>
Report-Link: http://lkml.kernel.org/r/CAKbGBLjC2Dx5vshxyGmQkcD+VwiAQLbHoXA9i7kvRB2-2opHZQ@mail.gmail.com
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Fixes: f30a79b012 ("perf tools: Add reference counting for cpu_map object")
Link: http://lkml.kernel.org/n/tip-j0u1bdhr47sa511sgg76kb8h@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb166ba1d7 upstream.
The regmap_irq_get_virq() can return 0 or -EINVAL in error conditions
but driver checked only for value of 0.
This could lead to a cast of -EINVAL to an unsigned int used as a
interrupt number for devm_request_threaded_irq(). Although this is not
yet fatal (devm_request_threaded_irq() will just fail with -EINVAL) but
might be a misleading when diagnosing errors.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: 6f1c1e71d9 ("mfd: max77686: Convert to use regmap_irq")
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a25f4a95ec upstream.
drivers/rtc/rtc-vr41xx.c:229: warning: ‘vr41xx_rtc_alarm_irq_enable’ defined but not used
Apparently the conversion to alarm_irq_enable forgot to wire up the
callback.
Fixes: 16380c153a ("RTC: Convert rtc drivers to use the alarm_irq_enable method")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit beda5fc1ff upstream.
Commit 30e7a65b3f (PM / Domains: Ensure subdomain is not in use
before removing) added a test to ensure that a subdomain is not a
master to another subdomain or if any devices are using the subdomain
before removing. This change incorrectly used the "slave_links" list to
determine if the subdomain is a master to another subdomain, where it
should have been using the "master_links" list instead. The
"slave_links" list will never be empty for a subdomain and so a
subdomain can never be removed. Fix this by testing if the
"master_links" list is empty instead.
Fixes: 30e7a65b3f (PM / Domains: Ensure subdomain is not in use before removing)
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c88c395f4a upstream.
We kept u_volt_min/max initialized to 0, when only the target voltage is
present in DT, instead of the target/min/max triplet.
This didn't go well with the regulator framework, as on few calls the
min voltage was set to target and max was set to 0 and so resulted in a
kernel crash like below:
kernel BUG at ../drivers/regulator/core.c:216!
[<c0684af4>] (regulator_check_voltage) from [<c06857ac>] (regulator_set_voltage_unlocked+0x58/0x230)
[<c06857ac>] (regulator_set_voltage_unlocked) from [<c06859ac>] (regulator_set_voltage+0x28/0x54)
[<c06859ac>] (regulator_set_voltage) from [<c0775b28>] (_set_opp_voltage+0x30/0x98)
[<c0775b28>] (_set_opp_voltage) from [<c0776630>] (dev_pm_opp_set_rate+0xf0/0x28c)
[<c0776630>] (dev_pm_opp_set_rate) from [<c096f784>] (__cpufreq_driver_target+0x184/0x2b4)
[<c096f784>] (__cpufreq_driver_target) from [<c0973760>] (dbs_check_cpu+0x1b0/0x1f4)
[<c0973760>] (dbs_check_cpu) from [<c0973f30>] (cpufreq_governor_dbs+0x324/0x5c4)
[<c0973f30>] (cpufreq_governor_dbs) from [<c0970958>] (__cpufreq_governor+0xe4/0x1ec)
[<c0970958>] (__cpufreq_governor) from [<c09711e0>] (cpufreq_init_policy+0x64/0x8c)
[<c09711e0>] (cpufreq_init_policy) from [<c09718cc>] (cpufreq_online+0x2fc/0x708)
[<c09718cc>] (cpufreq_online) from [<c0765ff0>] (subsys_interface_register+0x94/0xd8)
[<c0765ff0>] (subsys_interface_register) from [<c0970530>] (cpufreq_register_driver+0x14c/0x19c)
[<c0970530>] (cpufreq_register_driver) from [<c09746dc>] (dt_cpufreq_probe+0x70/0xec)
[<c09746dc>] (dt_cpufreq_probe) from [<c076907c>] (platform_drv_probe+0x4c/0xb0)
[<c076907c>] (platform_drv_probe) from [<c07678e0>] (driver_probe_device+0x214/0x2c0)
[<c07678e0>] (driver_probe_device) from [<c0767a18>] (__driver_attach+0x8c/0x90)
[<c0767a18>] (__driver_attach) from [<c0765c2c>] (bus_for_each_dev+0x68/0x9c)
[<c0765c2c>] (bus_for_each_dev) from [<c0766d78>] (bus_add_driver+0x1a0/0x218)
[<c0766d78>] (bus_add_driver) from [<c076810c>] (driver_register+0x78/0xf8)
[<c076810c>] (driver_register) from [<c0301d74>] (do_one_initcall+0x90/0x1d8)
[<c0301d74>] (do_one_initcall) from [<c1100e14>] (kernel_init_freeable+0x15c/0x1fc)
[<c1100e14>] (kernel_init_freeable) from [<c0b27a0c>] (kernel_init+0x8/0xf0)
[<c0b27a0c>] (kernel_init) from [<c0307d78>] (ret_from_fork+0x14/0x3c)
Code: e1550004 baffffeb e3a00000 e8bd8070 (e7f001f2)
Fix that by initializing u_volt_min/max to the target voltage in such cases.
Reported-and-tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: 274659029c (PM / OPP: Add support to parse "operating-points-v2" bindings)
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b64dbf849 upstream.
Signed integer overflow is undefined. Also I added a check for
"(offset < 0)" in scif_unregister() because that makes it match the
other conditions and because I didn't want to subtract a negative.
Fixes: ba612aa8b4 ('misc: mic: SCIF memory registration and unregistration')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 50e6315dba upstream.
Commit 985087dbcb 'misc: add support for bmp18x chips to the bmp085
driver' changed the BMP085 config symbol to a boolean. I see no
reason why the shared code cannot be built as a module, so change it
back to tristate.
Fixes: 985087dbcb ("misc: add support for bmp18x chips to the bmp085 driver")
Cc: Eric Andersson <eric.andersson@unixphere.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ee0cb5fb5 upstream.
The limbs are integers in the host endianness, so we can't simply
iterate over the individual bytes. The current code happens to work on
little-endian, because the order of the limbs in the MPI array is the
same as the order of the bytes in each limb, but it breaks on
big-endian.
Fixes: 0f74fbf77d ("MPI: Fix mpi_read_buffer")
Signed-off-by: Michal Marek <mmarek@suse.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 713fced8d1 upstream.
Commit 028cd86b79 ("video: da8xx-fb: fix the polarities of the
hsync/vsync pulse") fixes polarities of HSYNC/VSYNC pulse but
forgot to update known_lcd_panels[] which had sync values
according to old logic. This breaks LCD at least on DA850 EVM.
This patch fixes this issue and I have tested this for panel
"Sharp_LK043T1DG01" using DA850 EVM board.
Fixes: 028cd86b79 ("video: da8xx-fb: fix the polarities of the hsync/vsync pulse")
Signed-off-by: Sushaanth Srirangapathi <sushaanth.s@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c994c03c9 upstream.
When the scsi_dh core was moved into the scsi core module,
CONFIG_SCSI_DH became a 'bool' option, and now anything depending on it
can be built-in even when CONFIG_SCSI=m. This of course cannot link
successfully:
drivers/scsi/built-in.o: In function `rdac_init':
scsi_dh_alua.c:(.init.text+0x14): undefined reference to `scsi_register_device_handler'
scsi_dh_alua.c:(.init.text+0x64): undefined reference to `scsi_unregister_device_handler'
drivers/scsi/built-in.o: In function `alua_init':
scsi_dh_alua.c:(.init.text+0xb0): undefined reference to `scsi_register_device_handler'
As a workaround, this adds an extra dependency on CONFIG_SCSI, so
Kconfig can figure out whether built-in is allowed or not.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 086b91d052 ("scsi_dh: integrate into the core SCSI code")
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dec63a4dec upstream.
gcc-6.0 found an ancient bug in the paride driver, which had a
"module_param(verbose, bool, 0);" since before 2.6.12, but actually uses
it to accept '0', '1' or '2' as arguments:
drivers/block/paride/pd.c: In function 'pd_init_dev_parms':
drivers/block/paride/pd.c:298:29: warning: comparison of constant '1' with boolean expression is always false [-Wbool-compare]
#define DBMSG(msg) ((verbose>1)?(msg):NULL)
In 2012, Rusty did a cleanup patch that also changed the type of the
variable to 'bool', which introduced what is now a gcc warning.
This changes the type back to 'int' and adapts the module_param() line
instead, so it should work as documented in case anyone ever cares about
running the ancient driver with debugging.
Fixes: 90ab5ee941 ("module_param: make bool parameters really bool (drivers & misc)")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Rusty Russell <rusty@rustcorp.com.au>
Cc: Tim Waugh <tim@cyberelk.net>
Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Cc: Jens Axboe <axboe@fb.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e07ff94341 upstream.
The s5m8767_pmic_probe() function calls s5m8767_get_register() to
read data without checking the return code, which produces a compile-time
warning when that data is accessed:
drivers/regulator/s5m8767.c: In function 's5m8767_pmic_probe':
drivers/regulator/s5m8767.c:924:7: error: 'enable_reg' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/regulator/s5m8767.c:944:30: error: 'enable_val' may be used uninitialized in this function [-Werror=maybe-uninitialized]
This changes the s5m8767_get_register() function to return a -EINVAL
not just for an invalid register number but also for an invalid
regulator number, as both would result in returning uninitialized
data. The s5m8767_pmic_probe() function is then changed accordingly
to fail on a read error, as all the other callers of s5m8767_get_register()
already do.
In practice this probably cannot happen, as we don't call
s5m8767_get_register() with invalid arguments, but the gcc
warning seems valid in principle, in terms writing safe
error checking.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 9c4c60554a ("regulator: s5m8767: Convert to use regulator_[enable|disable|is_enabled]_regmap")
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b920cc3191 upstream.
Rockchip_spi_set_cs could be called by spi_setup, but
spi_setup may be called by device driver after runtime suspend.
Then the spi clock is closed, rockchip_spi_set_cs may access the
spi registers, which causes cpu block in some socs.
Fixes: 64e36824b3 ("spi/rockchip: add driver for Rockchip RK3xxx")
Signed-off-by: Huibin Hong <huibin.hong@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 920c720aa5 upstream.
Similar to commit b4b29f9485 ("locking/osq: Fix ordering of node
initialisation in osq_lock") the use of xchg_acquire() is
fundamentally broken with MCS like constructs.
Furthermore, it turns out we rely on the global transitivity of this
operation because the unlock path observes the pointer with a
READ_ONCE(), not an smp_load_acquire().
This is non-critical because the MCS code isn't actually used and
mostly serves as documentation, a stepping stone to the more complex
things we've build on top of the idea.
Reported-by: Andrea Parri <parri.andrea@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Fixes: 3552a07a9c ("locking/mcs: Use acquire/release semantics")
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b348d7dddb upstream.
Fix potential out-of-bounds write to urb->transfer_buffer
usbip handles network communication directly in the kernel. When receiving a
packet from its peer, usbip code parses headers according to protocol. As
part of this parsing urb->actual_length is filled. Since the input for
urb->actual_length comes from the network, it should be treated as untrusted.
Any entity controlling the network may put any value in the input and the
preallocated urb->transfer_buffer may not be large enough to hold the data.
Thus, the malicious entity is able to write arbitrary data to kernel memory.
Signed-off-by: Ignat Korchagin <ignat.korchagin@gmail.com>
Cc: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d7e69488bd upstream.
Currently, migration code increses num_poisoned_pages on *failed*
migration page as well as successfully migrated one at the trial of
memory-failure. It will make the stat wrong. As well, it marks the
page as PG_HWPoison even if the migration trial failed. It would mean
we cannot recover the corrupted page using memory-failure facility.
This patches fixes it.
Signed-off-by: Minchan Kim <minchan@kernel.org>
Reported-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7bf52fb891 upstream.
We have been reclaimed highmem zone if buffer_heads is over limit but
commit 6b4f7799c6 ("mm: vmscan: invoke slab shrinkers from
shrink_zone()") changed the behavior so it doesn't reclaim highmem zone
although buffer_heads is over the limit. This patch restores the logic.
Fixes: 6b4f7799c6 ("mm: vmscan: invoke slab shrinkers from shrink_zone()")
Signed-off-by: Minchan Kim <minchan@kernel.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 28093f9f34 upstream.
In gather_pte_stats() a THP pmd is cast into a pte, which is wrong
because the layouts may differ depending on the architecture. On s390
this will lead to inaccurate numa_maps accounting in /proc because of
misguided pte_present() and pte_dirty() checks on the fake pte.
On other architectures pte_present() and pte_dirty() may work by chance,
but there may be an issue with direct-access (dax) mappings w/o
underlying struct pages when HAVE_PTE_SPECIAL is set and THP is
available. In vm_normal_page() the fake pte will be checked with
pte_special() and because there is no "special" bit in a pmd, this will
always return false and the VM_PFNMAP | VM_MIXEDMAP checking will be
skipped. On dax mappings w/o struct pages, an invalid struct page
pointer would then be returned that can crash the kernel.
This patch fixes the numa_maps THP handling by introducing new "_pmd"
variants of the can_gather_numa_stats() and vm_normal_page() functions.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Konstantin Khlebnikov <koct9i@gmail.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66ee95d16a upstream.
HugeTLB pages cannot be split, so we use the compound_mapcount to track
rmaps.
Currently page_mapped() will check the compound_mapcount, but will also
go through the constituent pages of a THP compound page and query the
individual _mapcount's too.
Unfortunately, page_mapped() does not distinguish between HugeTLB and
THP compound pages and assumes that a compound page always needs to have
HPAGE_PMD_NR pages querying.
For most cases when dealing with HugeTLB this is just inefficient, but
for scenarios where the HugeTLB page size is less than the pmd block
size (e.g. when using contiguous bit on ARM) this can lead to crashes.
This patch adjusts the page_mapped function such that we skip the
unnecessary THP reference checks for HugeTLB pages.
Fixes: e1534ae950 ("mm: differentiate page_mapped() from page_mapcount() for compound pages")
Signed-off-by: Steve Capper <steve.capper@arm.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 264a0ae164 upstream.
Hello,
So, this ended up a lot simpler than I originally expected. I tested
it lightly and it seems to work fine. Petr, can you please test these
two patches w/o the lru drain drop patch and see whether the problem
is gone?
Thanks.
------ 8< ------
If charge moving is used, memcg performs relabeling of the affected
pages from its ->attach callback which is called under both
cgroup_threadgroup_rwsem and thus can't create new kthreads. This is
fragile as various operations may depend on workqueues making forward
progress which relies on the ability to create new kthreads.
There's no reason to perform charge moving from ->attach which is deep
in the task migration path. Move it to ->post_attach which is called
after the actual migration is finished and cgroup_threadgroup_rwsem is
dropped.
* move_charge_struct->mm is added and ->can_attach is now responsible
for pinning and recording the target mm. mem_cgroup_clear_mc() is
updated accordingly. This also simplifies mem_cgroup_move_task().
* mem_cgroup_move_task() is now called from ->post_attach instead of
->attach.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@kernel.org>
Debugged-and-tested-by: Petr Mladek <pmladek@suse.com>
Reported-by: Cyril Hrubis <chrubis@suse.cz>
Reported-by: Johannes Weiner <hannes@cmpxchg.org>
Fixes: 1ed1328792 ("sched, cgroup: replace signal_struct->group_rwsem with a global percpu_rwsem")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5cf1cacb49 upstream.
Since e93ad19d05 ("cpuset: make mm migration asynchronous"), cpuset
kicks off asynchronous NUMA node migration if necessary during task
migration and flushes it from cpuset_post_attach_flush() which is
called at the end of __cgroup_procs_write(). This is to avoid
performing migration with cgroup_threadgroup_rwsem write-locked which
can lead to deadlock through dependency on kworker creation.
memcg has a similar issue with charge moving, so let's convert it to
an official callback rather than the current one-off cpuset specific
function. This patch adds cgroup_subsys->post_attach callback and
makes cpuset register cpuset_post_attach_flush() as its ->post_attach.
The conversion is mostly one-to-one except that the new callback is
called under cgroup_mutex. This is to guarantee that no other
migration operations are started before ->post_attach callbacks are
finished. cgroup_mutex is one of the outermost mutex in the system
and has never been and shouldn't be a problem. We can add specialized
synchronization around __cgroup_procs_write() but I don't think
there's any noticeable benefit.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Li Zefan <lizefan@huawei.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 376bf125ac upstream.
This change is primarily an attempt to make it easier to realize the
optimizations the compiler performs in-case CONFIG_MEMCG_KMEM is not
enabled.
Performance wise, even when CONFIG_MEMCG_KMEM is compiled in, the
overhead is zero. This is because, as long as no process have enabled
kmem cgroups accounting, the assignment is replaced by asm-NOP
operations. This is possible because memcg_kmem_enabled() uses a
static_key_false() construct.
It also helps readability as it avoid accessing the p[] array like:
p[size - 1] which "expose" that the array is processed backwards inside
helper function build_detached_freelist().
Lastly this also makes the code more robust, in error case like passing
NULL pointers in the array. Which were previously handled before commit
033745189b ("slub: add missing kmem cgroup support to
kmem_cache_free_bulk").
Fixes: 033745189b ("slub: add missing kmem cgroup support to kmem_cache_free_bulk")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Vladimir Davydov <vdavydov@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 346c09f804 upstream.
The bug in a workqueue leads to a stalled IO request in MQ ctx->rq_list
with the following backtrace:
[ 601.347452] INFO: task kworker/u129:5:1636 blocked for more than 120 seconds.
[ 601.347574] Tainted: G O 4.4.5-1-storage+ #6
[ 601.347651] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 601.348142] kworker/u129:5 D ffff880803077988 0 1636 2 0x00000000
[ 601.348519] Workqueue: ibnbd_server_fileio_wq ibnbd_dev_file_submit_io_worker [ibnbd_server]
[ 601.348999] ffff880803077988 ffff88080466b900 ffff8808033f9c80 ffff880803078000
[ 601.349662] ffff880807c95000 7fffffffffffffff ffffffff815b0920 ffff880803077ad0
[ 601.350333] ffff8808030779a0 ffffffff815b01d5 0000000000000000 ffff880803077a38
[ 601.350965] Call Trace:
[ 601.351203] [<ffffffff815b0920>] ? bit_wait+0x60/0x60
[ 601.351444] [<ffffffff815b01d5>] schedule+0x35/0x80
[ 601.351709] [<ffffffff815b2dd2>] schedule_timeout+0x192/0x230
[ 601.351958] [<ffffffff812d43f7>] ? blk_flush_plug_list+0xc7/0x220
[ 601.352208] [<ffffffff810bd737>] ? ktime_get+0x37/0xa0
[ 601.352446] [<ffffffff815b0920>] ? bit_wait+0x60/0x60
[ 601.352688] [<ffffffff815af784>] io_schedule_timeout+0xa4/0x110
[ 601.352951] [<ffffffff815b3a4e>] ? _raw_spin_unlock_irqrestore+0xe/0x10
[ 601.353196] [<ffffffff815b093b>] bit_wait_io+0x1b/0x70
[ 601.353440] [<ffffffff815b056d>] __wait_on_bit+0x5d/0x90
[ 601.353689] [<ffffffff81127bd0>] wait_on_page_bit+0xc0/0xd0
[ 601.353958] [<ffffffff81096db0>] ? autoremove_wake_function+0x40/0x40
[ 601.354200] [<ffffffff81127cc4>] __filemap_fdatawait_range+0xe4/0x140
[ 601.354441] [<ffffffff81127d34>] filemap_fdatawait_range+0x14/0x30
[ 601.354688] [<ffffffff81129a9f>] filemap_write_and_wait_range+0x3f/0x70
[ 601.354932] [<ffffffff811ced3b>] blkdev_fsync+0x1b/0x50
[ 601.355193] [<ffffffff811c82d9>] vfs_fsync_range+0x49/0xa0
[ 601.355432] [<ffffffff811cf45a>] blkdev_write_iter+0xca/0x100
[ 601.355679] [<ffffffff81197b1a>] __vfs_write+0xaa/0xe0
[ 601.355925] [<ffffffff81198379>] vfs_write+0xa9/0x1a0
[ 601.356164] [<ffffffff811c59d8>] kernel_write+0x38/0x50
The underlying device is a null_blk, with default parameters:
queue_mode = MQ
submit_queues = 1
Verification that nullb0 has something inflight:
root@pserver8:~# cat /sys/block/nullb0/inflight
0 1
root@pserver8:~# find /sys/block/nullb0/mq/0/cpu* -name rq_list -print -exec cat {} \;
...
/sys/block/nullb0/mq/0/cpu2/rq_list
CTX pending:
ffff8838038e2400
...
During debug it became clear that stalled request is always inserted in
the rq_list from the following path:
save_stack_trace_tsk + 34
blk_mq_insert_requests + 231
blk_mq_flush_plug_list + 281
blk_flush_plug_list + 199
wait_on_page_bit + 192
__filemap_fdatawait_range + 228
filemap_fdatawait_range + 20
filemap_write_and_wait_range + 63
blkdev_fsync + 27
vfs_fsync_range + 73
blkdev_write_iter + 202
__vfs_write + 170
vfs_write + 169
kernel_write + 56
So blk_flush_plug_list() was called with from_schedule == true.
If from_schedule is true, that means that finally blk_mq_insert_requests()
offloads execution of __blk_mq_run_hw_queue() and uses kblockd workqueue,
i.e. it calls kblockd_schedule_delayed_work_on().
That means, that we race with another CPU, which is about to execute
__blk_mq_run_hw_queue() work.
Further debugging shows the following traces from different CPUs:
CPU#0 CPU#1
---------------------------------- -------------------------------
reqeust A inserted
STORE hctx->ctx_map[0] bit marked
kblockd_schedule...() returns 1
<schedule to kblockd workqueue>
request B inserted
STORE hctx->ctx_map[1] bit marked
kblockd_schedule...() returns 0
*** WORK PENDING bit is cleared ***
flush_busy_ctxs() is executed, but
bit 1, set by CPU#1, is not observed
As a result request B pended forever.
This behaviour can be explained by speculative LOAD of hctx->ctx_map on
CPU#0, which is reordered with clear of PENDING bit and executed _before_
actual STORE of bit 1 on CPU#1.
The proper fix is an explicit full barrier <mfence>, which guarantees
that clear of PENDING bit is to be executed before all possible
speculative LOADS or STORES inside actual work function.
Signed-off-by: Roman Pen <roman.penyaev@profitbricks.com>
Cc: Gioh Kim <gi-oh.kim@profitbricks.com>
Cc: Michael Wang <yun.wang@profitbricks.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: linux-block@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1bdb897039 upstream.
If x86_vector_alloc_irq() fails x86_vector_free_irqs() is invoked to cleanup
the already allocated vectors. This subsequently calls clear_vector_irq().
The failed irq has no vector assigned, which triggers the BUG_ON(!vector) in
clear_vector_irq().
We cannot suppress the call to x86_vector_free_irqs() for the failed
interrupt, because the other data related to this irq must be cleaned up as
well. So calling clear_vector_irq() with vector == 0 is legitimate.
Remove the BUG_ON and return if vector is zero,
[ tglx: Massaged changelog ]
Fixes: b5dc8e6c21 "x86/irq: Use hierarchical irqdomain to manage CPU interrupt vectors"
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e6bd18f57a upstream.
The drivers/infiniband stack uses write() as a replacement for
bi-directional ioctl(). This is not safe. There are ways to
trigger write calls that result in the return structure that
is normally written to user space being shunted off to user
specified kernel memory instead.
For the immediate repair, detect and deny suspicious accesses to
the write API.
For long term, update the user space libraries and the kernel API
to something that doesn't present the same security vulnerabilities
(likely a structured ioctl() interface).
The impacted uAPI interfaces are generally only available if
hardware from drivers/infiniband is installed in the system.
Reported-by: Jann Horn <jann@thejh.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
[ Expanded check to all known write() entry points ]
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc386ce76d upstream.
The port_open flag is not applicable for IBSS mode. IBSS data
path was broken when port_open flag was introduced.
This patch fixes the problem by correcting the checks.
Fixes: 5c8946330a ("mwifiex: enable traffic only when port is open")
Signed-off-by: chunfan chen <jeffc@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f4e7de63ab upstream.
When we fail to find the default gid index, we can't continue
processing in this routine or else we will pass a negative
index to later routines resulting in invalid memory access
attempts and a kernel oops.
Fixes: 03db3a2d81 (IB/core: Add RoCE GID table management)
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d6776bba44 upstream.
Keep IRQ mappings on context teardown. This won't leak IRQs as if we
allocate the mapping again, the generic code will give the same
mapping used last time.
Doing this works around a race in the generic code. Masking the
interrupt introduces a race which can crash the kernel or result in
IRQ that is never EOIed. The lost of EOI results in all subsequent
mappings to the same HW IRQ never receiving an interrupt.
We've seen this race with cxl test cases which are doing heavy context
startup and teardown at the same time as heavy interrupt load.
A fix to the generic code is being investigated also.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Tested-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Tested-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3020ca7118 upstream.
The VSync polarity was negative instead of positive for the 4k CEA formats.
I probably copy-and-pasted these from the DMT 4k format, which does have a
negative VSync polarity.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c1f6951a8 upstream.
When a buffer is being dequeued using VIDIOC_DQBUF IOCTL, the exact buffer
which will be dequeued is not known until the buffer has been removed from
the queue. The number of planes is specific to a buffer, not to the queue.
This does lead to the situation where multi-plane buffers may be requested
and queued with n planes, but VIDIOC_DQBUF IOCTL may be passed an argument
struct with fewer planes.
__fill_v4l2_buffer() however uses the number of planes from the dequeued
videobuf2 buffer, overwriting kernel memory (the m.planes array allocated
in video_usercopy() in v4l2-ioctl.c) if the user provided fewer
planes than the dequeued buffer had. Oops!
Fixes: b0e0e1f83d ("[media] media: videobuf2: Prepare to divide videobuf2")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7e0c3e265 upstream.
The number of planes in videobuf2 is specific to a buffer. In order to
verify that the planes array provided by the user is long enough, a new
vb2_buf_op is required.
Call __verify_planes_array() when the dequeued buffer is known. Return an
error to the caller if there was one, otherwise remove the buffer from the
done list.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b93876845c upstream.
When using a device is read/write mode, vb2 does not handle properly the
first select/poll operation.
The reason for this, is that when this code has been refactored, some of
the operations have changed their order, and now fileio emulator is not
started.
The reintroduced check to the core is enabled by a quirk flag, that
avoids this check by other subsystems like DVB.
Fixes: 49d8ab9fea ("media] media: videobuf2: Separate vb2_poll()")
Reported-by: Dimitrios Katsaros <patcherwork@gmail.com>
Cc: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 89a0956683 upstream.
On page unaligned frames, create_framevec forces get_vaddr_frames to
allocate an extra page at the end of the buffer. Under some
circumstances, this leads to -EINVAL on VIDIOC_QBUF.
E.g:
We have vm_a that vm_area that goes from 0x1000 to 0x3000. And a
frame that goes from 0x1800 to 0x2800, i.e. 2 pages.
frame_vector_create will be called with the following params:
get_vaddr_frames(0x1800, 2, write, 1, vec);
get_vaddr will allocate the first page after checking that the memory
0x1800-0x27ff is valid, but it will not allocate the second page because
the range 0x2800-0x37ff is out of the vm_a range. This results in
create_framevec returning -EFAULT
Error Trace:
[ 9083.793015] video0: VIDIOC_QBUF: 00:00:00.00000000 index=1,
type=vid-cap, flags=0x00002002, field=any, sequence=0,
memory=userptr, bytesused=0, offset/userptr=0x7ff2b023ca80, length=5765760
[ 9083.793028] timecode=00:00:00 type=0, flags=0x00000000,
frames=0, userbits=0x00000000
[ 9083.793117] video0: VIDIOC_QBUF: error -22: 00:00:00.00000000
index=2, type=vid-cap, flags=0x00000000, field=any, sequence=0,
memory=userptr, bytesused=0, offset/userptr=0x7ff2b07bc500, length=5765760
Also use true instead of 1 since that argument is a bool in the
get_vaddr_frames() prototype.
Fixes: 21fb0cb7ec ("[media] vb2: Provide helpers for mapping virtual addresses")
Reported-by: Albert Antony <albert@newtec.dk>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
[hans.verkuil@cisco.com: merged the 'bool' change into this patch]
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
commit 47325078f2 upstream.
The dummy component is reused for all cards so we special case and don't
bind it to any of them. This means that code like that displaying the
component widgets that tries to look at the card will crash. In the
future we will fix this by ensuring that the dummy component looks like
other components but that is invasive and so not suitable for a fix.
Instead add a special case check here.
Reported-by: Harry Pan <harry.pan@intel.com>
Suggested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 712a8038cc upstream.
When the ssm4567 is powered up the driver calles regcache_sync() to restore
the register map content. regcache_sync() assumes that the device is in its
power-on reset state. Make sure that this is the case by explicitly
resetting the ssm4567 register map before calling regcache_sync() otherwise
we might end up with a incorrect register map which leads to undefined
behaviour.
One such undefined behaviour was observed when returning from system
suspend while a playback stream is active, in that case the ssm4567 was
kept muted after resume.
Fixes: 1ee44ce030 ("ASoC: ssm4567: Add driver for Analog Devices SSM4567 amplifier")
Reported-by: Harsha Priya <harshapriya.n@intel.com>
Tested-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ba4bc32eaa upstream.
An older patch to convert the API in the s3c i2s driver
ended up passing a const pointer into a function that takes
a non-const pointer, so we now get a warning:
sound/soc/samsung/s3c2412-i2s.c: In function 's3c2412_iis_dev_probe':
sound/soc/samsung/s3c2412-i2s.c:172:9: error: passing argument 3 of 's3c_i2sv2_register_component' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
However, the s3c_i2sv2_register_component() function again
passes the pointer into another function taking a const, so
we just need to change its prototype.
Fixes: eca3b01d08 ("ASoC: switch over to use snd_soc_register_component() on s3c i2s")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a30b8f81d9 upstream.
Commit 52cbae0127 ("toshiba_acpi: Change default Hotkey enabling value")
changed the hotkeys enabling value, as it was the same value Windows uses,
however, it turns out that the value tells the EC that the driver will now
take care of the hardware events like the physical RFKill switch or the
pointing device toggle button.
This patch reverts such commit by changing the default hotkey enabling
value to 0x09, which enables hotkey events only, making the hardware
buttons working again.
Fixes bugs 113331 and 114941.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e1c7d6103 upstream.
Baytrail eMMC/SD/SDIO host controllers have been known to
hang. A change to a hardware setting has been found to
reduce the occurrence of such hangs. This patch ensures
the correct setting.
This patch applies cleanly to v4.4+. It could go to
earlier kernels also, so I will send backports to the
stable list in due course.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5508df8975 upstream.
It is reported that the following commit triggers regressions:
Linux commit: efaed9be99
ACPICA commit: 31178590dde82368fdb0f6b0e466b6c0add96c57
Subject: ACPICA: Events: Enhance acpi_ev_execute_reg_method() to
ensure no _REG evaluations can happen during OS early boot
stages
This is because that the ECDT support is not corrected in Linux, and Linux
requires to execute _REG for ECDT (though this sounds so wrong), we need to
ensure acpi_gbl_namespace_initialized is set before ECDT probing in order
for _REG to be executed. Since we have to move
"acpi_gbl_namespace_initialized = TRUE" to the initialization step
happening before ECDT probing, acpi_load_tables() is the best candidate for
now. Thus this patch fixes the regression by doing so.
But if the ECDT support is fixed, Linux will not execute _REG for ECDT, and
ECDT probing will happen before acpi_load_tables(). At that time, we still
want to ensure acpi_gbl_namespace_initialized is set after executing
acpi_ns_initialize_objects() (under the condition of
acpi_gbl_group_module_level_code = FALSE), this patch also moves
acpi_ns_initialize_objects() to acpi_load_tables() accordingly.
Since acpi_ns_initialize_objects() doesn't seem to be skippable, this
patch also removes ACPI_NO_OBJECT_INIT for the one invoked in
acpi_load_tables(). And since the default region handlers should always be
installed before loading the tables, this patch also removes useless
acpi_gbl_group_module_level_code check accordingly. Reported by Chris
Bainbridge, Fixed by Lv Zheng.
Fixes: efaed9be99 (ACPICA: Events: Enhance acpi_ev_execute_reg_method() to ensure no _REG evaluations can happen during OS early boot stages)
Reported-and-tested-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 10ff4c5239 upstream.
The exynos5 I2C controller driver always prepares and enables a clock
before using it and then disables unprepares it when the clock is not
used anymore.
But this can cause a possible ABBA deadlock in some scenarios since a
driver that uses regmap to access its I2C registers, will first grab
the regmap lock and then the I2C xfer function will grab the prepare
lock when preparing the I2C clock. But since the clock driver also
uses regmap for I2C accesses, preparing a clock will first grab the
prepare lock and then the regmap lock when using the regmap API.
An example of this happens on the Exynos5422 Odroid XU4 board where a
s2mps11 PMIC is used and both the s2mps11 regulators and clk drivers
share the same I2C regmap.
The possible deadlock is reported by the kernel lockdep:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(sec_core:428:(regmap)->lock);
lock(prepare_lock);
lock(sec_core:428:(regmap)->lock);
lock(prepare_lock);
*** DEADLOCK ***
Fix it by leaving the code prepared on probe and use {en,dis}able in
the I2C transfer function.
This patch is similar to commit 34e81ad5f0 ("i2c: s3c2410: fix ABBA
deadlock by keeping clock prepared") that fixes the same bug in other
driver for an I2C controller found in Samsung SoCs.
Reported-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 609d5a1b2b upstream.
Since commit ea8daa7b97 ("kbuild: Add option to turn incompatible
pointer check into error"), assignments from an incompatible pointer
types have become a hard error, eg:
drivers/i2c/busses/i2c-cpm.c:545:91: error: passing argument 3 of
'dma_alloc_coherent' from incompatible pointer type
Fix the build break by converting txdma & rxdma to dma_addr_t.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes: ea8daa7b97
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1342e0b7a6 upstream.
Tracing a workload that uses transactions gave a seg fault as follows:
perf record -e intel_pt// workload
perf report
Program received signal SIGSEGV, Segmentation fault.
0x000000000054b58c in intel_pt_reset_last_branch_rb (ptq=0x1a36110)
at util/intel-pt.c:929
929 ptq->last_branch_rb->nr = 0;
(gdb) p ptq->last_branch_rb
$1 = (struct branch_stack *) 0x0
(gdb) up
1148 intel_pt_reset_last_branch_rb(ptq);
(gdb) l
1143 if (ret)
1144 pr_err("Intel Processor Trace: failed to deliver transaction event
1145 ret);
1146
1147 if (pt->synth_opts.callchain)
1148 intel_pt_reset_last_branch_rb(ptq);
1149
1150 return ret;
1151 }
1152
(gdb) p pt->synth_opts.callchain
$2 = true
(gdb)
(gdb) bt
#0 0x000000000054b58c in intel_pt_reset_last_branch_rb (ptq=0x1a36110)
#1 0x000000000054c1e0 in intel_pt_synth_transaction_sample (ptq=0x1a36110)
#2 0x000000000054c5b2 in intel_pt_sample (ptq=0x1a36110)
Caused by checking the 'callchain' flag when it should have been the
'last_branch' flag. Fix that.
Reported-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Fixes: f14445ee72 ("perf intel-pt: Support generating branch stack")
Link: http://lkml.kernel.org/r/1460977068-11566-1-git-send-email-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f36fdacc5f upstream.
The current compile-time check for inversed IENB/CNTL does not
work in multiplatform boots: as soon as versatile is included
in the build, the IENB/CNTL is switched and breaks graphics.
Convert this to a runtime switch.
Cc: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Fixes: a29da136de ("ARM: versatile: convert to multi-platform")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 56fc350224 upstream.
Fixes the following scenario:
1. Page table bo allocated in vram and linked to man->lru.
tbo->list_kref.refcount=2
2. Page table bo is swapped out and removed from man->lru.
tbo->list_kref.refcount=1
3. Command submission from userspace. Page table bo is moved
to vram. ttm_bo_move_to_lru_tail() link it to man->lru and
don't increase the kref count.
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Flora Cui <Flora.Cui@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b3e885a05 upstream.
For reasons unknown Sandybridge GT1 (at least) will eventually hang when
it encounters a ring wraparound at offset 0. The test case that
reproduces the bug reliably forces a large number of interrupted context
switches, thereby causing very frequent ring wraparounds, but there are
similar bug reports in the wild with the same symptoms, seqno writes
stop just before the wrap and the ringbuffer at address 0. It is also
timing crucial, but adding various delays hasn't helped pinpoint where
the window lies.
Whether the fault is restricted to the ringbuffer itself or the GTT
addressing is unclear, but moving the ringbuffer fixes all the hangs I
have been able to reproduce.
References: (e.g.) https://bugs.freedesktop.org/show_bug.cgi?id=93262
Testcase: igt/gem_exec_whisper/render-contexts-interruptible #snb-gt1
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1460565315-7748-12-git-send-email-chris@chris-wilson.co.uk
(cherry picked from commit a687a43a48)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d43f3ebf12 upstream.
Currently for the case where there is enough space at the end of Ring
buffer for accommodating only the base request, the wrapround is done
immediately and as a result the base request gets added at the start
of Ring buffer. But there may not be enough free space at the beginning
to accommodate the base request, as before the wraparound, the wait was
effectively done for the reserved_size free space from the start of
Ring buffer. In such a case there is a potential of Ring buffer overflow,
the instructions at the head of Ring (ACTHD) can get overwritten.
Since the base request can fit in the remaining space, there is no need
to wraparound immediately. The wraparound will anyway happen later when
the reserved part starts getting used.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1457688402-10411-1-git-send-email-akash.goel@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit 782f6bc0ab)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 93fce95442 upstream.
At the end of the function we expect "status" to be zero, but it's
either -EINVAL or uninitialized.
Fixes: 788bf83db3 ('drm/amdkfd: Add wave control operation to debugger')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d919161b67 upstream.
We're supposed to pass the primary DP encoder to intel_ddi_clk_select(),
not the fake MST encoder. Do so.
There's no real bug here though, since intel_ddi_clk_select() only
checks if the encoder type is EDP (which it isn't for either the
primary DP encoder or the fake MST encoder), and it gets the DDI port
via intel_ddi_get_encoder_port() (which knows how to do the
fake->primary->port dance itself).
Fixes: e404ba8 ("drm/i915: Setup DDI clk for MST on SKL")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449597590-6971-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c5857e3f94 upstream.
The change fixes potential oops while accessing iomem on invalid address
if devm_ioremap_resource() fails due to some reason.
The devm_ioremap_resource() function returns ERR_PTR() and never returns
NULL, which makes useless a following check for NULL.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Fixes: 3a9f595702 ("pwm: Add Broadcom BCM7038 PWM controller support")
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 263efde31f upstream.
We can thank KASAN for finding this, otherwise I probably would have spent
hours on it. This fixes a somewhat harder to trigger kernel panic, occuring
while enabling MST where the port we were currently updating the payload on
would have all of it's refs dropped before we finished what we were doing:
==================================================================
BUG: KASAN: use-after-free in drm_dp_update_payload_part1+0xb3f/0xdb0 [drm_kms_helper] at addr ffff8800d29de018
Read of size 4 by task Xorg/973
=============================================================================
BUG kmalloc-2048 (Tainted: G B W ): kasan: bad access detected
-----------------------------------------------------------------------------
INFO: Allocated in drm_dp_add_port+0x1aa/0x1ed0 [drm_kms_helper] age=16477 cpu=0 pid=2175
___slab_alloc+0x472/0x490
__slab_alloc+0x20/0x40
kmem_cache_alloc_trace+0x151/0x190
drm_dp_add_port+0x1aa/0x1ed0 [drm_kms_helper]
drm_dp_send_link_address+0x526/0x960 [drm_kms_helper]
drm_dp_check_and_send_link_address+0x1ac/0x210 [drm_kms_helper]
drm_dp_mst_link_probe_work+0x77/0xd0 [drm_kms_helper]
process_one_work+0x562/0x1350
worker_thread+0xd9/0x1390
kthread+0x1c5/0x260
ret_from_fork+0x22/0x40
INFO: Freed in drm_dp_free_mst_port+0x50/0x60 [drm_kms_helper] age=7521 cpu=0 pid=2175
__slab_free+0x17f/0x2d0
kfree+0x169/0x180
drm_dp_free_mst_port+0x50/0x60 [drm_kms_helper]
drm_dp_destroy_connector_work+0x2b8/0x490 [drm_kms_helper]
process_one_work+0x562/0x1350
worker_thread+0xd9/0x1390
kthread+0x1c5/0x260
ret_from_fork+0x22/0x40
which on this T460s, would eventually lead to kernel panics in somewhat
random places later in intel_mst_enable_dp() if we got lucky enough.
Signed-off-by: Lyude <cpaul@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit deba0a2af9 upstream.
With the joys of things running concurrently, there's always a chance
that the port we get passed in drm_dp_payload_send_msg() isn't actually
valid anymore. Because of this, we need to make sure we validate the
reference to the port before we use it otherwise we risk running into
various race conditions. For instance, on the Dell MST monitor I have
here for testing, hotplugging it enough times causes us to kernel panic:
[drm:intel_mst_enable_dp] 1
[drm:drm_dp_update_payload_part2] payload 0 1
[drm:intel_get_hpd_pins] hotplug event received, stat 0x00200000, dig 0x10101011, pins 0x00000020
[drm:intel_hpd_irq_handler] digital hpd port B - short
[drm:intel_dp_hpd_pulse] got hpd irq on port B - short
[drm:intel_dp_check_mst_status] got esi 00 10 00
[drm:drm_dp_update_payload_part2] payload 1 1
general protection fault: 0000 [#1] SMP
…
Call Trace:
[<ffffffffa012b632>] drm_dp_update_payload_part2+0xc2/0x130 [drm_kms_helper]
[<ffffffffa032ef08>] intel_mst_enable_dp+0xf8/0x180 [i915]
[<ffffffffa0310dbd>] haswell_crtc_enable+0x3ed/0x8c0 [i915]
[<ffffffffa030c84d>] intel_atomic_commit+0x5ad/0x1590 [i915]
[<ffffffffa01db877>] ? drm_atomic_set_crtc_for_connector+0x57/0xe0 [drm]
[<ffffffffa01dc4e7>] drm_atomic_commit+0x37/0x60 [drm]
[<ffffffffa0130a3a>] drm_atomic_helper_set_config+0x7a/0xb0 [drm_kms_helper]
[<ffffffffa01cc482>] drm_mode_set_config_internal+0x62/0x100 [drm]
[<ffffffffa01d02ad>] drm_mode_setcrtc+0x3cd/0x4e0 [drm]
[<ffffffffa01c18e3>] drm_ioctl+0x143/0x510 [drm]
[<ffffffffa01cfee0>] ? drm_mode_setplane+0x1b0/0x1b0 [drm]
[<ffffffff810f79a7>] ? hrtimer_start_range_ns+0x1b7/0x3a0
[<ffffffff81212962>] do_vfs_ioctl+0x92/0x570
[<ffffffff81590852>] ? __sys_recvmsg+0x42/0x80
[<ffffffff81212eb9>] SyS_ioctl+0x79/0x90
[<ffffffff816b4e32>] entry_SYSCALL_64_fastpath+0x1a/0xa4
RIP [<ffffffffa012b026>] drm_dp_payload_send_msg+0x146/0x1f0 [drm_kms_helper]
Which occurs because of the hotplug event shown in the log, which ends
up causing DRM's dp helpers to drop the port we're updating the payload
on and panic.
Signed-off-by: Lyude <cpaul@redhat.com>
Reviewed-by: David Airlie <airlied@linux.ie>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d5b7803c4 upstream.
When crtc/timing is disabled on boot the dig block
should be stopped in order ignore timing from crtc,
reset the steering fifo otherwise we get display
corruption or hung in dp sst mode.
v2: agd: fix coding style
Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5dcec693f upstream.
Allowing userptr bo which are basicly a list of page from some vma
(so either anonymous page or file backed page) would lead to serious
corruption of kernel structures and counters (because we overwrite
the page->mapping field when mapping buffer).
This will already block if the buffer was populated before anyone does
try to mmap it because then TTM_PAGE_FLAG_SG would be set in in the
ttm_tt flags. But that flag is check before ttm_tt_populate in the ttm
vm fault handler.
So to be safe just add a check to verify_access() callback.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fix was written against drm-next, but when it was
backported to 4.5 as a stable fix, the driver internal
structure change was missed. Fix that up here to avoid
a hang due to waiting for the wrong sequence number.
v2: agd: fix up commit message
Signed-off-by: Grigori Goronzy <greg@chown.ath.cx>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
commit 07b48ac4bb upstream.
With the change to stashing just the IOVA-page-aligned remainder of the
CPU-page offset rather than the whole thing, the failure path in
__invalidate_sg() also needs tweaking to account for that in the case of
differing page sizes where the two offsets may not be equivalent.
Similarly in __finalise_sg(), lest the architecture-specific wrappers
later get the wrong address for cache maintenance on sync or unmap.
Fixes: 164afb1d85 ("iommu/dma: Use correct offset in map_sg")
Reported-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e315604834 upstream.
Commit 61289cb ('iommu/amd: Remove old alias handling code')
removed the old alias handling code from the AMD IOMMU
driver because this is now handled by the IOMMU core code.
But this also removed the handling of PCI aliases, which is
not handled by the core code. This caused issues with PCI
devices that have hidden PCIe-to-PCI bridges that rewrite
the request-id.
Fix this bug by re-introducing some of the removed functions
from commit 61289cbaf6 and add a alias field
'struct iommu_dev_data'. This field carrys the return value
of the get_alias() function and uses that instead of the
amd_iommu_alias_table[] array in the code.
Fixes: 61289cbaf6 ('iommu/amd: Remove old alias handling code')
Tested-by: Tomasz Golinski <tomaszg@math.uwb.edu.pl>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 56b367c0cd upstream.
pcs_parse_bits_in_pinctrl_entry uses ffs which gives bit indices
ranging from 1 to MAX. This leads to a corner case where we try to request
the pin number = MAX and fails.
bit_pos value is being calculted using ffs. pin_num_from_lsb uses
bit_pos value. pins array is populated with:
pin + pin_num_from_lsb.
The above is 1 more than usual bit indices as bit_pos uses ffs to compute
first set bit. Hence the last of the pins array is populated with the MAX
value and not MAX - 1 which causes error when we call pin_request.
mask_pos is rightly calculated as ((pcs->fmask) << (bit_pos - 1))
Consequently val_pos and submask are correct.
Hence use __ffs which gives (ffs(x) - 1) as the first bit set.
fixes: 4e7e8017a8 ("pinctrl: pinctrl-single: enhance to configure multiple pins of different modules")
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5fedbb9239 upstream.
The debounce time unit for gpio_chip.set_debounce is us but
mtk_gpio_set_debounce regard it as ms.
Fix this by correct debounce time array dbnc_arr so it can find correct
debounce setting. Debounce time for first debounce setting is 500us,
correct this as well.
While I'm at it, also change the debounce time array name to
"debounce_time" for readability.
Signed-off-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 13aa38e291 upstream.
The Xen framebuffer driver selects the xen keyboard driver, so the latter
will be built-in if XEN_FBDEV_FRONTEND=y. However, when CONFIG_INPUT
is a loadable module, this configuration cannot work. On mainline kernels,
the symbol will be enabled but not used, while in combination with
a patch I have to detect such useless configurations, we get the
expected link failure:
drivers/input/built-in.o: In function `xenkbd_remove':
xen-kbdfront.c:(.text+0x2f0): undefined reference to `input_unregister_device'
xen-kbdfront.c:(.text+0x30e): undefined reference to `input_unregister_device'
This removes the extra "select", as it just causes more trouble than
it helps. In theory, some defconfig file might break if it has
XEN_FBDEV_FRONTEND in it but not INPUT_XEN_KBDDEV_FRONTEND. The Kconfig
fragment we ship in the kernel (kernel/configs/xen.config) however
already enables both, and anyone using an old .config file would
keep having both enabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Suggested-by: David Vrabel <david.vrabel@citrix.com>
Fixes: 36c1132e34 ("xen kconfig: fix select INPUT_XEN_KBDDEV_FRONTEND")
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eda5ecc0a6 upstream.
The trigger delay algorithm that converts from microseconds to
the register value looks incorrect. According to most of the PMIC
documentation, the equation is
delay (Seconds) = (1 / 1024) * 2 ^ (x + 4)
except for one case where the documentation looks to have a
formatting issue and the equation looks like
delay (Seconds) = (1 / 1024) * 2 x + 4
Most likely this driver was written with the improper
documentation to begin with. According to the downstream sources
the valid delays are from 2 seconds to 1/64 second, and the
latter equation just doesn't make sense for that. Let's fix the
algorithm and the range check to match the documentation and the
downstream sources.
Reported-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: 92d57a73e4 ("input: Add support for Qualcomm PMIC8XXX power key")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 162f98dea4 upstream.
The gtco driver expects at least one valid endpoint. If given malicious
descriptors that specify 0 for the number of endpoints, it will crash in
the probe function. Ensure there is at least one endpoint on the interface
before using it.
Also let's fix a minor coding style issue.
The full correct report of this issue can be found in the public
Red Hat Bugzilla:
https://bugzilla.redhat.com/show_bug.cgi?id=1283385
Reported-by: Ralf Spenneberg <ralf@spenneberg.net>
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e272602039 upstream.
All existing users of NETLINK_URELEASE use it to clean up resources that
were previously allocated to a socket via some command. As a result, no
users require getting this notification for unbound sockets.
Sending it for unbound sockets, however, is a problem because any user
(including unprivileged users) can create a socket that uses the same ID
as an existing socket. Binding this new socket will fail, but if the
NETLINK_URELEASE notification is generated for such sockets, the users
thereof will be tricked into thinking the socket that they allocated the
resources for is closed.
In the nl80211 case, this will cause destruction of virtual interfaces
that still belong to an existing hostapd process; this is the case that
Dmitry noticed. In the NFC case, it will cause a poll abort. In the case
of netlink log/queue it will cause them to stop reporting events, as if
NFULNL_CFG_CMD_UNBIND/NFQNL_CFG_CMD_UNBIND had been called.
Fix this problem by checking that the socket is bound before generating
the NETLINK_URELEASE notification.
Signed-off-by: Dmitry Ivanov <dima@ubnt.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f815cdde3 upstream.
A non-privileged user can create a netlink socket with the same port_id as
used by an existing open nl80211 netlink socket (e.g. as used by a hostapd
process) with a different protocol number.
Closing this socket will then lead to the notification going to nl80211's
socket release notification handler, and possibly cause an action such as
removing a virtual interface.
Fix this issue by checking that the netlink protocol is NETLINK_GENERIC.
Since generic netlink has no notifier chain of its own, we can't fix the
problem more generically.
Fixes: 026331c4d9 ("cfg80211/mac80211: allow registering for and sending action frames")
Signed-off-by: Dmitry Ivanov <dima@ubnt.com>
[rewrite commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4705e02498 upstream.
We need to update the user TM feature bits (PPC_FEATURE2_HTM and
PPC_FEATURE2_HTM) to mirror what we do with the kernel TM feature
bit.
At the moment, if firmware reports TM is not available we turn off
the kernel TM feature bit but leave the userspace ones on. Userspace
thinks it can execute TM instructions and it dies trying.
This (together with a QEMU patch) fixes PR KVM, which doesn't currently
support TM.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit beff82374b upstream.
scan_features() updates cpu_user_features but not cpu_user_features2.
Amongst other things, cpu_user_features2 contains the user TM feature
bits which we must keep in sync with the kernel TM feature bit.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6997e57d69 upstream.
The REAL_LE feature entry in the ibm_pa_feature struct is missing an MMU
feature value, meaning all the remaining elements initialise the wrong
values.
This means instead of checking for byte 5, bit 0, we check for byte 0,
bit 0, and then we incorrectly set the CPU feature bit as well as MMU
feature bit 1 and CPU user feature bits 0 and 2 (5).
Checking byte 0 bit 0 (IBM numbering), means we're looking at the
"Memory Management Unit (MMU)" feature - ie. does the CPU have an MMU.
In practice that bit is set on all platforms which have the property.
This means we set CPU_FTR_REAL_LE always. In practice that seems not to
matter because all the modern cpus which have this property also
implement REAL_LE, and we've never needed to disable it.
We're also incorrectly setting MMU feature bit 1, which is:
#define MMU_FTR_TYPE_8xx 0x00000002
Luckily the only place that looks for MMU_FTR_TYPE_8xx is in Book3E
code, which can't run on the same cpus as scan_features(). So this also
doesn't matter in practice.
Finally in the CPU user feature mask, we're setting bits 0 and 2. Bit 2
is not currently used, and bit 0 is:
#define PPC_FEATURE_PPC_LE 0x00000001
Which says the CPU supports the old style "PPC Little Endian" mode.
Again this should be harmless in practice as no 64-bit CPUs implement
that mode.
Fix the code by adding the missing initialisation of the MMU feature.
Also add a comment marking CPU user feature bit 2 (0x4) as reserved. It
would be unsafe to start using it as old kernels incorrectly set it.
Fixes: 44ae3ab335 ("powerpc: Free up some CPU feature bits by moving out MMU-related features")
Signed-off-by: Anton Blanchard <anton@samba.org>
[mpe: Flesh out changelog, add comment reserving 0x4]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 340ff60ae9 upstream.
After conversion to new AEAD interface, tcrypt tests fail as follows:
[...]
[ 1.145414] alg: aead: Test 1 failed on encryption for authenc-hmac-sha1-cbc-aes-talitos
[ 1.153564] 00000000: 53 69 6e 67 6c 65 20 62 6c 6f 63 6b 20 6d 73 67
[ 1.160041] 00000010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1.166509] 00000020: 00 00 00 00
[...]
Fix them by providing the correct cipher in & cipher out pointers,
i.e. must skip over associated data in src and dst S/G.
While here, fix a problem with the HW S/G table index usage:
tbl_off must be updated after the pointer to the table entries is set.
Fixes: aeb4c132f3 ("crypto: talitos - Convert to new AEAD interface")
Reported-by: Jonas Eymann <J.Eymann@gmx.net>
Signed-off-by: Horia Geant? <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0851561d9c upstream.
In sha_complete_job, incorrect mcryptd_hash_request_ctx pointer is used
when check and complete other jobs. If the memory of first completed req
is freed, while still completing other jobs in the func, kernel will
crash since NULL pointer is assigned to RIP.
Signed-off-by: Xiaodong Liu <xiaodong.liu@intel.com>
Acked-by: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f709b45ec4 upstream.
Prevent information from leaking to userspace by doing a memset to 0 of
the export state structure before setting the structure values and copying
it. This prevents un-initialized padding areas from being copied into the
export area.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7fdf966326 upstream.
Currently paging download buffer is freed during the
the unloading of the opmode which happens when the driver
is unloaded.
This causes a memory leak since the paging download
buffer is allocated every time we enable the
interface, so the download buffer can be allocated many
times, but only be freed once.
Free paging download buffer during disabling of the
interface.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9fc515bc9e upstream.
IWL_INFO is not an error but still printed by default.
"can't access the RSA semaphore it is write protected" seems
worrisome but it is not really a problem.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9d89d9e61d upstream.
Newer machines might use a different (larger) format for function
measurement blocks. To ensure that we comply with the alignment
requirement on these machines and prevent memory corruption (when
firmware writes more data than we expect) add 16 padding bytes
at the end of the fmb.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1becf03545 upstream.
When the config TDP level is not nominal (level = 0), the MSR values for
reading level 1 and level 2 ratios contain power in low 14 bits and actual
ratio bits are at bits [23:16]. The current processing for level 1 and
level 2 is wrong as there is no shift done to get actual ratio.
Fixes: 6a35fc2d6c (cpufreq: intel_pstate: get P1 from TAR when available)
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d5468d7afa upstream.
Commit 588afcc1c0 ("[media] usbvision fix overflow of interfaces
array")' should be reverted, because:
* "!dev->actconfig->interface[ifnum]" won't catch a case where the value
is not NULL but some garbage. This way the system may crash later with
GPF.
* "(ifnum >= USB_MAXINTERFACES)" does not cover all the error
conditions. "ifnum" should be compared to "dev->actconfig->
desc.bNumInterfaces", i.e. compared to the number of "struct
usb_interface" kzalloc()-ed, not to USB_MAXINTERFACES.
* There is a "struct usb_device" leak in this error path, as there is
usb_get_dev(), but no usb_put_dev() on this path.
* There is a bug of the same type several lines below with number of
endpoints. The code is accessing hard-coded second endpoint
("interface->endpoint[1].desc") which may not exist. It would be great
to handle this in the same patch too.
* All the concerns above are resolved by already-accepted commit fa52bd50
("[media] usbvision: fix crash on detecting device with invalid
configuration")
* Mailing list message:
http://www.spinics.net/lists/linux-media/msg94832.html
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b2d7a9cd3f upstream.
Commit 5c5fb40de8 ("PCI: imx6: Add support for active-low reset GPIO")
cause regressions on some boards like MX6 Gateworks Ventana, for example.
The reason for the breakage is that this commit sets the GPIO polarity in
the wrong logic level.
Also, the commit log is wrong because active-low reset GPIO is what the
driver used to support since the beginning.
So keep the old behavior that ignores the GPIO polarity specified in the
device tree and treat the PCI reset GPIO as active-low.
Reported-by: Krzysztof Hałasa <khalasa@piap.pl>
Tested-by: Tim Harvey <tharvey@gateworks.com> # Gateworks Ventana
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bfaddd9fc8 upstream.
This reverts commit e64c952efb.
ATPX is the ACPI method for controlling AMD PowerXpress laptops.
There are flags to indicate which methods are supported. If
the dGPU power down flag is not supported, the driver needs to
implement the dGPU power down manually. We had previously
always forced the driver to assume the ATPX dGPU power down
was present, but this causes problems on boards where it is
not, leading to GPU hangs when attempting to power down the
dGPU. Manual dGPU power down is not currently supported in
the Linux driver. Some laptops indicate that the ATPX
dGPU power down method is not present, but it actually
apparently is. I'm not sure if this is a bios bug and it should
be set or if there is a reason it was unset and the method should
not be used. This is not an issue on other OSes since both the
ATPX and the manual driver power down methods are supported.
This is apparently fairly widespread, so just revert for now.
bugs:
https://bugzilla.kernel.org/show_bug.cgi?id=115321https://bugzilla.kernel.org/show_bug.cgi?id=116581https://bugzilla.kernel.org/show_bug.cgi?id=116251
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9e60290dba upstream.
After unplugging a DP MST display from the system, we have to go through
and destroy all of the DRM connectors associated with it since none of
them are valid anymore. Unfortunately, intel_dp_destroy_mst_connector()
doesn't do a good enough job of ensuring that throughout the destruction
process that no modesettings can be done with the connectors. As it is
right now, intel_dp_destroy_mst_connector() works like this:
* Take all modeset locks
* Clear the configuration of the crtc on the connector, if there is one
* Drop all modeset locks, this is required because of circular
dependency issues that arise with trying to remove the connector from
sysfs with modeset locks held
* Unregister the connector
* Take all modeset locks, again
* Do the rest of the required cleaning for destroying the connector
* Finally drop all modeset locks for good
This only works sometimes. During the destruction process, it's very
possible that a userspace application will attempt to do a modesetting
using the connector. When we drop the modeset locks, an ioctl handler
such as drm_mode_setcrtc has the oppurtunity to take all of the modeset
locks from us. When this happens, one thing leads to another and
eventually we end up committing a mode with the non-existent connector:
[drm:intel_dp_link_training_clock_recovery [i915]] *ERROR* failed to enable link training
[drm:intel_dp_aux_ch] dp_aux_ch timeout status 0x7cf0001f
[drm:intel_dp_start_link_train [i915]] *ERROR* failed to start channel equalization
[drm:intel_dp_aux_ch] dp_aux_ch timeout status 0x7cf0001f
[drm:intel_mst_pre_enable_dp [i915]] *ERROR* failed to allocate vcpi
And in some cases, such as with the T460s using an MST dock, this
results in breaking modesetting and/or panicking the system.
To work around this, we now unregister the connector at the very
beginning of intel_dp_destroy_mst_connector(), grab all the modesetting
locks, and then hold them until we finish the rest of the function.
Signed-off-by: Lyude <cpaul@redhat.com>
Signed-off-by: Rob Clark <rclark@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1458155884-13877-1-git-send-email-cpaul@redhat.com
(cherry picked from commit 1f7717552e)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d59a1f71ff upstream.
The SPICE protocol considers the position of a cursor to be the location
of its active pixel on the display, so the cursor is drawn with its
top-left corner at "(x - hot_spot_x, y - hot_spot_y)" but the DRM cursor
position gives the location where the top-left corner should be drawn,
with the hotspot being a hint for drivers that need it.
This fixes the location of the window resize cursors when using Fluxbox
with the QXL DRM driver and both the QXL and modesetting X drivers.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1447845445-2116-1-git-send-email-john@metanate.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 78a121d82d upstream.
Most calls to nvkm_ramht_new use 0x8000 as the size. This results in a
fairly sizeable chunk of memory to be allocated, which may not be
available with kzalloc. Since this is done fairly rarely (once per
channel), use vzalloc instead.
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: Sven Joachim <svenjoac@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 89e9e66ba1 upstream.
If userspace calls UNLOCK_PI unconditionally without trying the TID -> 0
transition in user space first then the user space value might not have the
waiters bit set. This opens the following race:
CPU0 CPU1
uval = get_user(futex)
lock(hb)
lock(hb)
futex |= FUTEX_WAITERS
....
unlock(hb)
cmpxchg(futex, uval, newval)
So the cmpxchg fails and returns -EINVAL to user space, which is wrong because
the futex value is valid.
To handle this (yes, yet another) corner case gracefully, check for a flag
change and retry.
[ tglx: Massaged changelog and slightly reworked implementation ]
Fixes: ccf9e6a80d ("futex: Make unlock_pi more robust")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Darren Hart <dvhart@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1460723739-5195-1-git-send-email-bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fba7cd681b upstream.
The recent decoupling of pagefault disable and preempt disable added an
explicit preempt_disable/enable() pair to the futex_atomic_cmpxchg_inatomic()
implementation in asm-generic/futex.h. But it forgot to add preempt_enable()
calls to the error handling code pathes, which results in a preemption count
imbalance.
This is observable on boot when the test for atomic_cmpxchg() is calling
futex_atomic_cmpxchg_inatomic() on a NULL pointer.
Add the missing preempt_enable() calls to the error handling code pathes.
[ tglx: Massaged changelog ]
Fixes: d9b9ff8c18 ("sched/preempt, futex: Disable preemption in UP futex_atomic_cmpxchg_inatomic() explicitly")
Signed-off-by: Romain Perier <romain.perier@free-electrons.com>
Cc: linux-arch@vger.kernel.org
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1460640963-690-1-git-send-email-romain.perier@free-electrons.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb03ed2163 upstream.
The recent bug report suggests that BCLK setup for i915 HSW/BDW needs
to be updated at each HDMI hotplug, not only at initialization and
resume. That is, we need to update HSW_EM4 and HSW_EM5 registers at
ELD notification, too. Otherwise the HDMI audio may be out of sync
and played in a wrong pitch.
However, the HDA codec driver has no access to the controller
registers, and currently the code managing these registers is in
hda_intel.c, i.e. local to the controller driver. For allowing the
explicit BCLK update from the codec driver, as in this patch, the
former haswell_set_bclk() in hda_intel.c is moved to hdac_i915.c and
exposed as snd_hdac_i915_set_bclk(). This is called from both the HDA
controller driver and intel_pin_eld_notify() in HDMI codec driver.
Along with this change, snd_hdac_get_display_clk() gets dropped as
it's no longer used.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91410
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 037e119738 upstream.
Fixes audio output on a ThinkPad X260, when using Lenovo CES 2013
docking station series (basic, pro, ultra).
Signed-off-by: Conrad Kostecki <ck+linuxkernel@bl4ckb0x.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9859a971ca upstream.
Add HD Audio Device PCI ID for the Intel Broxton-T platform.
It is an HDA Intel PCH controller.
Signed-off-by: Lu, Han <han.lu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit de3df8a986 upstream.
Although one weird behavior about the input path (inconsistent D0/D3
switch) on Cirrus CS420x codecs was fixed in the previous commit,
there is still an issue on some Mac machines: the capture stream
stalls when switching the ADCs on the fly. More badly, this keeps
stuck until the next reboot.
The dynamic ADC switching is already a bit fragile and assuming
optimistically that the chip accepts the frequent power changes. On
Cirrus codecs, this doesn't seem applicable.
As a quick workaround, we pin down the ADCs to keep up in D0 when
spec->dyn_adc_switch is set. In this way, the ADCs are kept up only
for the system that were confirmed to be broken.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=116171
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit afecb146d8 upstream.
The Optiplex 9020m with Haswell-DT processor needs a quirk for the
headset jack at the front of the machine to be able to use microphones.
A quirk for this model was originally added in 3127899, but c77900e
removed it in favour of a more generic version.
Unfortunately, pin configurations can changed based on firmware/BIOS
versions, and the generic version doesn't have any effect on newer
versions of the machine/firmware anymore.
With help from David Henningsson <diwic@ubuntu.com>
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 50fd4987c4 upstream.
We've got a regression report that the recording on Mac with a cirrus
codec doesn't work any longer. This turned out to be the missing
power up to D0 by power_save_node enablement.
After analyzing the traces, we found out that the culprit is that the
codec advertises the "actual" power state of a few nodes to be D0
while the "target" power state is D3. This inconsistency is usually
OK, as it implies the power transition. But in the case of cirrus
codec, this seems to be stuck to D3 while it's not actually D0.
This patch addresses the issue by checking the power state difference
more strictly. It sends the power-state change verb unless both the
target and the actual power states show the given value.
We may introduce yet another flag indicating the possible broken
hardware power state, but it's anyway safer to set the proper power
state even in a transition (at least it's harmless as long as the
target state is same). So this simpler change was applied now.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=116171
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 103f6112f2 upstream.
Huge pages are not normally available to PV guests. Not suppressing
hugetlbfs use results in an endless loop of page faults when user mode
code tries to access a hugetlbfs mapped area (since the hypervisor
denies such PTEs to be created, but error indications can't be
propagated out of xen_set_pte_at(), just like for various of its
siblings), and - once killed in an oops like this:
kernel BUG at .../fs/hugetlbfs/inode.c:428!
invalid opcode: 0000 [#1] SMP
...
RIP: e030:[<ffffffff811c333b>] [<ffffffff811c333b>] remove_inode_hugepages+0x25b/0x320
...
Call Trace:
[<ffffffff811c3415>] hugetlbfs_evict_inode+0x15/0x40
[<ffffffff81167b3d>] evict+0xbd/0x1b0
[<ffffffff8116514a>] __dentry_kill+0x19a/0x1f0
[<ffffffff81165b0e>] dput+0x1fe/0x220
[<ffffffff81150535>] __fput+0x155/0x200
[<ffffffff81079fc0>] task_work_run+0x60/0xa0
[<ffffffff81063510>] do_exit+0x160/0x400
[<ffffffff810637eb>] do_group_exit+0x3b/0xa0
[<ffffffff8106e8bd>] get_signal+0x1ed/0x470
[<ffffffff8100f854>] do_signal+0x14/0x110
[<ffffffff810030e9>] prepare_exit_to_usermode+0xe9/0xf0
[<ffffffff814178a5>] retint_user+0x8/0x13
This is CVE-2016-3961 / XSA-174.
Reported-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Juergen Gross <JGross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luis R. Rodriguez <mcgrof@suse.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: xen-devel <xen-devel@lists.xenproject.org>
Link: http://lkml.kernel.org/r/57188ED802000078000E431C@prv-mh.provo.novell.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f5177f0fd upstream.
The CPU controller hasn't kept up with the various changes in the whole
cgroup initialization / destruction sequence, and commit:
2e91fa7f6d ("cgroup: keep zombies associated with their original cgroups")
caused it to explode.
The reason for this is that zombies do not inhibit css_offline() from
being called, but do stall css_released(). Now we tear down the cfs_rq
structures on css_offline() but zombies can run after that, leading to
use-after-free issues.
The solution is to move the tear-down to css_released(), which
guarantees nobody (including no zombies) is still using our cgroup.
Furthermore, a few simple cleanups are possible too. There doesn't
appear to be any point to us using css_online() (anymore?) so fold that
in css_alloc().
And since cgroup code guarantees an RCU grace period between
css_released() and css_free() we can forgo using call_rcu() and free the
stuff immediately.
Suggested-by: Tejun Heo <tj@kernel.org>
Reported-by: Kazuki Yamaguchi <k@rhe.jp>
Reported-by: Niklas Cassel <niklas.cassel@axis.com>
Tested-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 2e91fa7f6d ("cgroup: keep zombies associated with their original cgroups")
Link: http://lkml.kernel.org/r/20160316152245.GY6344@twins.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9097103f06 upstream.
When the driver is initialized in a pure device-tree platform, the
driver's probe fails allocating the dma channel :
[ 525.624435] pxa3xx-nand 43100000.nand: no resource defined for data DMA
[ 525.632088] pxa3xx-nand 43100000.nand: alloc nand resource failed
The reason is that the DMA IO resource is not acquired through platform
resources but by OF bindings.
Fix this by ensuring that DMA IO resources are only queried in the non
device-tree case.
Fixes: 8f5ba31aa5 ("mtd: nand: pxa3xx-nand: switch to dmaengine")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6bab1c6afd upstream.
The current number of requestor lines is limited to 31. This was an
error of a previous commit, as this number is platform dependent, and is
actually :
- for pxa25x: 40 requestor lines
- for pxa27x: 75 requestor lines
- for pxa3xx: 100 requestor lines
The previous testing did not reveal the faulty constant as on pxa[23]xx
platforms, only camera, MSL and USB are above requestor 32, and in these
only the camera has a driver using dma.
Fixes: e87ffbdf06 ("dmaengine: pxa_dma: fix the no-requestor case")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23f49fd2ea upstream.
The dynamic or on demand pm_runtime does not work correctly on am335x and
am437x due to interference with hwmod.
Fall back using the pm_runtime usage as it was in the old driver stack,
meaning that at probe time call pm_runtime_enable() and
pm_runtime_get_sync() for the TPTCs as well.
Fixes: 1be5336bc7 ("dmaengine: edma: New device tree binding")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reported-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 689d3c5ecc upstream.
When based on the CCR_ENABLE bit the channel is stopped we should not call
omap_dma_callback(), only change the return value to DMA_COMPLETE. Client
drivers will do the right thing to clean up the channel after the transfer
has been completed.
Check the CCR_ENABLE only if the channel is running and not paused since
pause in sDMA means that the channel is stopped.
This will fix one hard to reproduce race condition when the channel is
terminated during transfer (affecting cyclic operation).
Fixes: 1a7cf7b26f ("dmaengine: omap-dma: Handle cases when the channel is polled for completion")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a197f3c7d4 upstream.
The commit f0579c8cea ("dmaengine: hsu: speed up residue calculation")
speeded up calculation of the queued descriptor but broke the initial residue
value for active descriptor.
In accordance with documentation the hardware descriptor is updated each time
DMA transfered some bytes. It means we have to calculate a sum of lengths of
non-submitted hardware descriptors and whatever current values in the hardware.
Do this straightforward.
Fixes: f0579c8cea ("dmaengine: hsu: speed up residue calculation")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f4bc0abff upstream.
There is a typo in documentation regarding to descriptor empty bit (DESCE)
which is set to 1 when descriptor is empty. Thus, status register at the end of
a transfer usually returns all DESCE bits set and thus it will never be zero.
Moreover, there are 2 bits (CDESC) that encode current descriptor, on which
interrupt has been asserted. In case when we have few descriptors programmed we
might have non-zero value.
Remove DESCE and CDESC bits from DMA channel status register (HSU_CH_SR) when
reading it.
Fixes: 2b49e0c567 ("dmaengine: append hsu DMA driver")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3fe6409c23 upstream.
The commit 8950052029 ("dmaengine: dw: apply both HS interfaces and remove
slave_id usage") cleaned up the code to avoid usage of depricated slave_id
member of generic slave configuration.
Meanwhile it broke the master selection by removing important call to
dwc_set_masters() in ->device_alloc_chan_resources() which copied masters from
custom slave configuration to the internal channel structure.
Everything works until now since there is no customized connection of
DesignWare DMA IP to the bus, i.e. one bus and one or more masters are in use.
The configurations where 2 masters are connected to the different masters are
not working anymore. We are expecting one user of such configuration and need
to select masters properly. Besides that it is obviously a performance
regression since only one master is in use in multi-master configuration.
Select masters in accordance with what user asked for. Keep this patch in a form
more suitable for back porting.
We are safe to take necessary data in ->device_alloc_chan_resources() because
we don't support generic slave configuration embedded into custom one, and thus
the only way to provide such is to use the parameter to a filter function which
is called exactly before channel resource allocation.
While here, replase BUG_ON to less noisy dev_warn() and prevent channel
allocation in case of error.
Fixes: 8950052029 ("dmaengine: dw: apply both HS interfaces and remove slave_id usage")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 87243deb88 upstream.
Starting with 4.1 the tracing subsystem has its own filesystem
which is automounted in the tracing subdirectory of debugfs.
Prior to this debugfs could be bind mounted in a cloned mount
namespace, but if tracefs has been mounted under debugfs this
now fails because there is a locked child mount. This creates
a regression for container software which bind mounts debugfs
to satisfy the assumption of some userspace software.
In other pseudo filesystems such as proc and sysfs we're already
creating mountpoints like this in such a way that no dirents can
be created in the directories, allowing them to be exceptions to
some MNT_LOCKED tests. In fact we're already do this for the
tracefs mountpoint in sysfs.
Do the same in debugfs_create_automount(), since the intention
here is clearly to create a mountpoint. This fixes the regression,
as locked child mounts on permanently empty directories do not
cause a bind mount to fail.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3e26a691fe upstream.
Based on Sergey's test patch [1], this fixes zram with lz4 compression
on big endian cpus.
Note that the 64-bit preprocessor test is not a cleanup, it's part of
the fix, since those identifiers are bogus (for example, __ppc64__
isn't defined anywhere else in the kernel, which means we'd fall into
the 32-bit definitions on ppc64).
Tested on ppc64 with no regression on x86_64.
[1] http://marc.info/?l=linux-kernel&m=145994470805853&w=4
Suggested-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6545b60baa upstream.
Commit 9567366fef ("dm cache metadata: fix READ_LOCK macros and
cleanup WRITE_LOCK macros") uses down_write() instead of down_read() in
cmd_read_lock(), yet up_read() is used to release the lock in
READ_UNLOCK(). Fix it.
Fixes: 9567366fef ("dm cache metadata: fix READ_LOCK macros and cleanup WRITE_LOCK macros")
Signed-off-by: Ahmed Samy <f.fallen45@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9567366fef upstream.
The READ_LOCK macro was incorrectly returning -EINVAL if
dm_bm_is_read_only() was true -- it will always be true once the cache
metadata transitions to read-only by dm_cache_metadata_set_read_only().
Wrap READ_LOCK and WRITE_LOCK multi-statement macros in do {} while(0).
Also, all accesses of the 'cmd' argument passed to these related macros
are now encapsulated in parenthesis.
A follow-up patch can be developed to eliminate the use of macros in
favor of pure C code. Avoiding that now given that this needs to apply
to stable@.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Fixes: d14fcf3dd7 ("dm cache: make sure every metadata function checks fail_io")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 38740a5b87 upstream.
When using asynchronous read or write operations on the USB endpoints the
issuer of the IO request is notified by calling the ki_complete() callback
of the submitted kiocb when the URB has been completed.
Calling this ki_complete() callback will free kiocb. Make sure that the
structure is no longer accessed beyond that point, otherwise undefined
behaviour might occur.
Fixes: 2e4c7553cd ("usb: gadget: f_fs: add aio support")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e86103a757 upstream.
On BXT platform Host Controller and Device Controller figure as
same PCI device but with different device function. HCD should
not pass data to Device Controller but only to Host Controllers.
Checking if companion device is Host Controller, otherwise skip.
Signed-off-by: Robert Dobrowolski <robert.dobrowolski@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9a85f6e61 upstream.
Otherwise generic-xhci and xhci-platform which have no data get wrongly
detected as XHCI_PLAT_TYPE_MARVELL_ARMADA by xhci_plat_type_is().
This fixes a regression in v4.5 for STiH407 family SoC's which use the
synopsis dwc3 IP, whereby the disable_clk error path gets taken due to
wrongly being detected as XHCI_PLAT_TYPE_MARVELL_ARMADA and the hcd never
gets added.
I suspect this will also fix other dwc3 DT platforms such as Exynos,
although I've only tested on STih410 SoC.
Fixes: 4efb2f6941 ("usb: host: xhci-plat: add struct xhci_plat_priv")
Cc: gregory.clement@free-electrons.com
Cc: yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 98d74f9cea upstream.
PCI hotpluggable xhci controllers such as some Alpine Ridge solutions will
remove the xhci controller from the PCI bus when the last USB device is
disconnected.
Add a flag to indicate that the host is being removed to avoid queueing
configure_endpoint commands for the dropped endpoints.
For PCI hotplugged controllers this will prevent 5 second command timeouts
For static xhci controllers the configure_endpoint command is not needed
in the removal case as everything will be returned, freed, and the
controller is reset.
For now the flag is only set for PCI connected host controllers.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0a380be823 upstream.
On some xHCI controllers (e.g. R-Car SoCs), the AC64 bit (bit 0) of
HCCPARAMS1 is set to 1. However, the xHCs don't support 64-bit
address memory pointers actually. So, in this case, this driver should
call dma_set_coherent_mask(dev, DMA_BIT_MASK(32)) in xhci_gen_setup().
Otherwise, the xHCI controller will be died after a usb device is
connected if it runs on above 4GB physical memory environment.
So, this patch adds a new quirk XHCI_NO_64BIT_SUPPORT to resolve
such an issue.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 671ffdff5b upstream.
Give USB3 devices a better chance to enumerate at USB 3 speeds if
they are connected to a suspended host.
Solves an issue with NEC uPD720200 host hanging when partially
enumerating a USB3 device as USB2 after host controller runtime resume.
Tested-by: Mike Murdoch <main.haarp@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ca4a23810 upstream.
Commit 127500ccb7 ("ARM: OMAP2+: Only write the sysconfig on idle
when necessary") talks about verification of sysconfig cache value before
updating it, only during idle path. But the patch is adding the
verification in the enable path. So, adding the check in a proper place
as per the commit description.
Not keeping this check during enable path as there is a chance of losing
context and it is safe to do on idle as the context of the register will
never be lost while the device is active.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Cc: Jon Hunter <jonathanh@nvidia.com>
Fixes: commit 127500ccb7 "ARM: OMAP2+: Only write the sysconfig on idle when necessary"
[paul@pwsan.com: appears to have been caused by my own mismerge of the
originally posted patch]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 456e8d5348 upstream.
The following commits:
commit 3fa609755c ("ARM: omap2: restore OMAP4 barrier behaviour")
commit f746929ffd ("Revert "ARM: OMAP4: remove dead kconfig option OMAP4_ERRATA_I688"")
and
commit ea827ad5ff ("ARM: DRA7: Provide proper IO map table")
came in around the same time, unfortunately this seem to have missed
initializing the barrier for DRA7 platforms - omap5_map_io was reused
for dra7 till it was split out by the last patch. barrier_init
needs to be hence carried forward as it is valid for DRA7 family of
processors as they are for OMAP5.
Fixes: ea827ad5ff ("ARM: DRA7: Provide proper IO map table")
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d41676dddd upstream.
EDMA was allocating DMA channels 32 and 33 for memcpy usage, out of which
channel 33 is actually used by DES crypto engine. This bad allocation of
the channel causes a crash in the DES crypto engine, as the channel
gets configured for memcpy usage instead of hardware <-> memory DMA.
Fixed by allocating DMA channels 58 and 59 for memcpy usage (I2C0 RX/TX),
which are not used by anybody.
Fixes: cce1ee0001 ("ARM: DTS: am437x: Use the new DT bindings for
the eDMA3")
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Suggested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cfe1580a64 upstream.
commit 55ee7017ee ("arm: omap2: board-generic: use omap4_local_timer_init
for AM437x") makes synctimer32k as the clocksource on AM43xx. By default
the synctimer32k is clocked by 32K RTC OSC on AM43xx. But this 32K RTC OSC
is not available on epos boards which makes it fail to boot.
Synctimer32k can also be clocked by a peripheral PLL, so making this as
clock parent for synctimer3k on epos boards.
Fixes: 55ee7017ee ("arm: omap2: board-generic: use omap4_local_timer_init for AM437x")
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c5631c73f upstream.
On a host that runs NTP, corrections can have a direct impact on
the background timer that we program on the behalf of a vcpu.
In particular, NTP performing a forward correction will result in
a timer expiring sooner than expected from a guest point of view.
Not a big deal, we kick the vcpu anyway.
But on wake-up, the vcpu thread is going to perform a check to
find out whether or not it should block. And at that point, the
timer check is going to say "timer has not expired yet, go back
to sleep". This results in the timer event being lost forever.
There are multiple ways to handle this. One would be record that
the timer has expired and let kvm_cpu_has_pending_timer return
true in that case, but that would be fairly invasive. Another is
to check for the "short sleep" condition in the hrtimer callback,
and restart the timer for the remaining time when the condition
is detected.
This patch implements the latter, with a bit of refactoring in
order to avoid too much code duplication.
Reported-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc5b7f3bf1 upstream.
An interrupt handler that uses the fpu can kill a KVM VM, if it runs
under the following conditions:
- the guest's xcr0 register is loaded on the cpu
- the guest's fpu context is not loaded
- the host is using eagerfpu
Note that the guest's xcr0 register and fpu context are not loaded as
part of the atomic world switch into "guest mode". They are loaded by
KVM while the cpu is still in "host mode".
Usage of the fpu in interrupt context is gated by irq_fpu_usable(). The
interrupt handler will look something like this:
if (irq_fpu_usable()) {
kernel_fpu_begin();
[... code that uses the fpu ...]
kernel_fpu_end();
}
As long as the guest's fpu is not loaded and the host is using eager
fpu, irq_fpu_usable() returns true (interrupted_kernel_fpu_idle()
returns true). The interrupt handler proceeds to use the fpu with
the guest's xcr0 live.
kernel_fpu_begin() saves the current fpu context. If this uses
XSAVE[OPT], it may leave the xsave area in an undesirable state.
According to the SDM, during XSAVE bit i of XSTATE_BV is not modified
if bit i is 0 in xcr0. So it's possible that XSTATE_BV[i] == 1 and
xcr0[i] == 0 following an XSAVE.
kernel_fpu_end() restores the fpu context. Now if any bit i in
XSTATE_BV == 1 while xcr0[i] == 0, XRSTOR generates a #GP. The
fault is trapped and SIGSEGV is delivered to the current process.
Only pre-4.2 kernels appear to be vulnerable to this sequence of
events. Commit 653f52c ("kvm,x86: load guest FPU context more eagerly")
from 4.2 forces the guest's fpu to always be loaded on eagerfpu hosts.
This patch fixes the bug by keeping the host's xcr0 loaded outside
of the interrupts-disabled region where KVM switches into guest mode.
Suggested-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: David Matlack <dmatlack@google.com>
[Move load after goto cancel_injection. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7cc8cbcf82 upstream.
Commit 4dffbfc48d ("arm64/efi: mark UEFI reserved regions as
MEMBLOCK_NOMAP") updated the mapping logic of both the RuntimeServices
regions as well as the kernel's copy of the UEFI memory map to set the
MEMBLOCK_NOMAP flag, which causes these regions to be omitted from the
kernel direct mapping, and from being covered by a struct page.
For the RuntimeServices regions, this is an obvious win, since the contents
of these regions have significance to the firmware executable code itself,
and are mapped in the EFI page tables using attributes that are described in
the UEFI memory map, and which may differ from the attributes we use for
mapping system RAM. It also prevents the contents from being modified
inadvertently, since the EFI page tables are only live during runtime
service invocations.
None of these concerns apply to the allocation that covers the UEFI memory
map, since it is entirely owned by the kernel. Setting the MEMBLOCK_NOMAP on
the region did allow us to use ioremap_cache() to map it both on arm64 and
on ARM, since the latter does not allow ioremap_cache() to be used on
regions that are covered by a struct page.
The ioremap_cache() on ARM restriction will be lifted in the v4.7 timeframe,
but in the mean time, it has been reported that commit 4dffbfc48d causes
a regression on 64k granule kernels. This is due to the fact that, given
the 64 KB page size, the region that we end up removing from the kernel
direct mapping is rounded up to 64 KB, and this 64 KB page frame may be
shared with the initrd when booting via GRUB (which does not align its
EFI_LOADER_DATA allocations to 64 KB like the stub does). This will crash
the kernel as soon as it tries to access the initrd.
Since the issue is specific to arm64, revert back to memblock_reserve()'ing
the UEFI memory map when running on arm64. This is a temporary fix for v4.5
and v4.6, and will be superseded in the v4.7 timeframe when we will be able
to move back to memblock_reserve() unconditionally.
Fixes: 4dffbfc48d ("arm64/efi: mark UEFI reserved regions as MEMBLOCK_NOMAP")
Reported-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Jeremy Linton <jeremy.linton@arm.com>
Cc: Mark Langsdorf <mlangsdo@redhat.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a7297a6a3a upstream.
Starting from commit e36f620428(block: split bios to max possible length),
block core starts to split bio in the middle of bvec.
Unfortunately loop dio/aio doesn't consider this situation, and
always treat 'iter.iov_offset' as zero. Then filesystem corruption
is observed.
This patch figures out the offset of the base bvevc via
'bio->bi_iter.bi_bvec_done' and fixes the issue by passing the offset
to iov iterator.
Fixes: e36f620428 (block: split bios to max possible length)
Cc: Keith Busch <keith.busch@intel.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b30a337ca2 upstream.
The initialization of partition's percpu_ref should have been done before
sending out KOBJ_ADD uevent, which may cause userspace to read partition
table. So the uninitialized percpu_ref may be accessed in data path.
This patch fixes this issue reported by Naveen.
Reported-by: Naveen Kaje <nkaje@codeaurora.org>
Tested-by: Naveen Kaje <nkaje@codeaurora.org>
Fixes: 6c71013ecb7e2(block: partition: convert percpu ref)
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9aaf3437aa upstream.
Commit 520bd7a8b4 ("mmc: core: Optimize boot time by detecting cards
simultaneously") causes regressions for some platforms.
These platforms relies on fixed mmcblk device indexes, instead of
deploying the defacto standard with UUID/PARTUUID. In other words their
rootfs needs to be available at hardcoded paths, like /dev/mmcblk0p2.
Such guarantees have never been made by the kernel, but clearly the above
commit changes the behaviour. More precisely, because of that the order
changes of how cards becomes detected, so do their corresponding mmcblk
device indexes.
As the above commit significantly improves boot time for some platforms
(magnitude of seconds), let's avoid reverting this change but instead
restore the behaviour of how mmcblk device indexes becomes picked.
By using the same index for the mmcblk device as for the corresponding mmc
host device, the probe order of mmc host devices decides the index we get
for the mmcblk device.
For those platforms that suffers from a regression, one could expect that
this updated behaviour should be sufficient to meet their expectations of
"fixed" mmcblk device indexes.
Another side effect from this change, is that the same index is used for
the mmc host device, the mmcblk device and the mmc block queue. That
should clarify their relationship.
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Reported-by: Laszlo Fiat <laszlo.fiat@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Fixes: 520bd7a8b4 ("mmc: core: Optimize boot time by detecting cards
simultaneously")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 972e6a993f upstream.
The usbhid driver has inconsistently duplicated code in its post-reset,
resume, and reset-resume pathways.
reset-resume doesn't check HID_STARTED before trying to
restart the I/O queues.
resume fails to clear the HID_SUSPENDED flag if HID_STARTED
isn't set.
resume calls usbhid_restart_queues() with usbhid->lock held
and the others call it without holding the lock.
The first item in particular causes a problem following a reset-resume
if the driver hasn't started up its I/O. URB submission fails because
usbhid->urbin is NULL, and this triggers an unending reset-retry loop.
This patch fixes the problem by creating a new subroutine,
hid_restart_io(), to carry out all the common activities. It also
adds some checks that were missing in the original code:
After a reset, there's no need to clear any halted endpoints.
After a resume, if a reset is pending there's no need to
restart any I/O until the reset is finished.
After a resume, if the interrupt-IN endpoint is halted there's
no need to submit the input URB until the halt has been
cleared.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Daniel Fraga <fragabr@gmail.com>
Tested-by: Daniel Fraga <fragabr@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 580549ef6b upstream.
Looks like recent changes in the Wacom driver made the Bamboo ONE crashes.
The tablet behaves as if it was a regular Bamboo device with pen, touch
and pad, but there is no physical pad connected to it.
The weird part is that the pad is still sending events and given that
there is no input node connected to it, we get anull pointer exception.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1317116
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit adcdd0d5a1 upstream.
This is Dell usb dock audio workaround.
It was fixed the master volume keep lower.
[Some background: the patch essentially skips the controls of a couple
of FU volumes. Although the firmware exposes the dB and the value
information via the usb descriptor, changing the values (we set the
min volume as default) screws up the device. Although this has been
fixed in the newer firmware, the devices are shipped with the old
firmware, thus we need the workaround in the driver side. -- tiwai]
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b4203ff546 upstream.
Plantronics BT300 does not support reading the sample rate which leads
to many lines of "cannot get freq at ep 0x1". This patch adds the USB
ID of the BT300 to quirks.c and avoids those error messages.
Signed-off-by: Dennis Kadioglu <denk@post.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f03b24a851 upstream.
Phoenix Audio TMX320 gives the similar error when the sample rate is
asked:
usb 2-1.3: 2:1: cannot get freq at ep 0x85
usb 2-1.3: 1:1: cannot get freq at ep 0x2
....
Add the corresponding USB-device ID (1de7:0014) to
snd_usb_get_sample_rate_quirk() list.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=110221
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c636b95ec5 upstream.
The Lenovo Thinkpad T460s requires the alc_fixup_tpt440_dock as well in
order to get working sound output on the docking stations headphone jack.
Patch tested on a Thinkpad T460s (20F9CT01WW) using a ThinkPad Ultradock
on kernel 4.4.6.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Tested-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 023d8218ec upstream.
The commit [bd48128539: ALSA: hda - Fix forgotten HDMI
monitor_present update] covered the missing update of monitor_present
flag, but this caused a regression for devices without the i915 eld
notifier. Since the old code supposed that pin_eld->monitor_present
was updated by the caller side, the hdmi_present_sense_via_verbs()
doesn't update the temporary eld->monitor_present but only
pin_eld->monitor_present, which is now overridden in update_eld().
The fix is to update pin_eld->monitor_present as well before calling
update_eld().
Note that this may still leave monitor_present flag in an inconsistent
state when the driver repolls, but this is at least the old behavior.
More proper fix will follow in the later patch.
Fixes: bd48128539 ('ALSA: hda - Fix forgotten HDMI monitor_present update')
Signed-off-by: Hyungwon Hwang <hyungwon.hwang7@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 01d6b2a40a upstream.
Add support and PCI IDs for more Broxton host controllers
Other BXT IDs were added in v4.4 so cc'ing stable. This patch
is dependent on commit 163cbe31e5 ("mmc: sdhci-pci: Fix card
detect race for Intel BXT/APL") but that is already in stable
since v4.4.4.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 56f23fdbb6 upstream.
If we rename an inode A (be it a file or a directory), create a new
inode B with the old name of inode A and under the same parent directory,
fsync inode B and then power fail, at log tree replay time we end up
removing inode A completely. If inode A is a directory then all its files
are gone too.
Example scenarios where this happens:
This is reproducible with the following steps, taken from a couple of
test cases written for fstests which are going to be submitted upstream
soon:
# Scenario 1
mkfs.btrfs -f /dev/sdc
mount /dev/sdc /mnt
mkdir -p /mnt/a/x
echo "hello" > /mnt/a/x/foo
echo "world" > /mnt/a/x/bar
sync
mv /mnt/a/x /mnt/a/y
mkdir /mnt/a/x
xfs_io -c fsync /mnt/a/x
<power failure happens>
The next time the fs is mounted, log tree replay happens and
the directory "y" does not exist nor do the files "foo" and
"bar" exist anywhere (neither in "y" nor in "x", nor the root
nor anywhere).
# Scenario 2
mkfs.btrfs -f /dev/sdc
mount /dev/sdc /mnt
mkdir /mnt/a
echo "hello" > /mnt/a/foo
sync
mv /mnt/a/foo /mnt/a/bar
echo "world" > /mnt/a/foo
xfs_io -c fsync /mnt/a/foo
<power failure happens>
The next time the fs is mounted, log tree replay happens and the
file "bar" does not exists anymore. A file with the name "foo"
exists and it matches the second file we created.
Another related problem that does not involve file/data loss is when a
new inode is created with the name of a deleted snapshot and we fsync it:
mkfs.btrfs -f /dev/sdc
mount /dev/sdc /mnt
mkdir /mnt/testdir
btrfs subvolume snapshot /mnt /mnt/testdir/snap
btrfs subvolume delete /mnt/testdir/snap
rmdir /mnt/testdir
mkdir /mnt/testdir
xfs_io -c fsync /mnt/testdir # or fsync some file inside /mnt/testdir
<power failure>
The next time the fs is mounted the log replay procedure fails because
it attempts to delete the snapshot entry (which has dir item key type
of BTRFS_ROOT_ITEM_KEY) as if it were a regular (non-root) entry,
resulting in the following error that causes mount to fail:
[52174.510532] BTRFS info (device dm-0): failed to delete reference to snap, inode 257 parent 257
[52174.512570] ------------[ cut here ]------------
[52174.513278] WARNING: CPU: 12 PID: 28024 at fs/btrfs/inode.c:3986 __btrfs_unlink_inode+0x178/0x351 [btrfs]()
[52174.514681] BTRFS: Transaction aborted (error -2)
[52174.515630] Modules linked in: btrfs dm_flakey dm_mod overlay crc32c_generic ppdev xor raid6_pq acpi_cpufreq parport_pc tpm_tis sg parport tpm evdev i2c_piix4 proc
[52174.521568] CPU: 12 PID: 28024 Comm: mount Tainted: G W 4.5.0-rc6-btrfs-next-27+ #1
[52174.522805] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS by qemu-project.org 04/01/2014
[52174.524053] 0000000000000000 ffff8801df2a7710 ffffffff81264e93 ffff8801df2a7758
[52174.524053] 0000000000000009 ffff8801df2a7748 ffffffff81051618 ffffffffa03591cd
[52174.524053] 00000000fffffffe ffff88015e6e5000 ffff88016dbc3c88 ffff88016dbc3c88
[52174.524053] Call Trace:
[52174.524053] [<ffffffff81264e93>] dump_stack+0x67/0x90
[52174.524053] [<ffffffff81051618>] warn_slowpath_common+0x99/0xb2
[52174.524053] [<ffffffffa03591cd>] ? __btrfs_unlink_inode+0x178/0x351 [btrfs]
[52174.524053] [<ffffffff81051679>] warn_slowpath_fmt+0x48/0x50
[52174.524053] [<ffffffffa03591cd>] __btrfs_unlink_inode+0x178/0x351 [btrfs]
[52174.524053] [<ffffffff8118f5e9>] ? iput+0xb0/0x284
[52174.524053] [<ffffffffa0359fe8>] btrfs_unlink_inode+0x1c/0x3d [btrfs]
[52174.524053] [<ffffffffa038631e>] check_item_in_log+0x1fe/0x29b [btrfs]
[52174.524053] [<ffffffffa0386522>] replay_dir_deletes+0x167/0x1cf [btrfs]
[52174.524053] [<ffffffffa038739e>] fixup_inode_link_count+0x289/0x2aa [btrfs]
[52174.524053] [<ffffffffa038748a>] fixup_inode_link_counts+0xcb/0x105 [btrfs]
[52174.524053] [<ffffffffa038a5ec>] btrfs_recover_log_trees+0x258/0x32c [btrfs]
[52174.524053] [<ffffffffa03885b2>] ? replay_one_extent+0x511/0x511 [btrfs]
[52174.524053] [<ffffffffa034f288>] open_ctree+0x1dd4/0x21b9 [btrfs]
[52174.524053] [<ffffffffa032b753>] btrfs_mount+0x97e/0xaed [btrfs]
[52174.524053] [<ffffffff8108e1b7>] ? trace_hardirqs_on+0xd/0xf
[52174.524053] [<ffffffff8117bafa>] mount_fs+0x67/0x131
[52174.524053] [<ffffffff81193003>] vfs_kern_mount+0x6c/0xde
[52174.524053] [<ffffffffa032af81>] btrfs_mount+0x1ac/0xaed [btrfs]
[52174.524053] [<ffffffff8108e1b7>] ? trace_hardirqs_on+0xd/0xf
[52174.524053] [<ffffffff8108c262>] ? lockdep_init_map+0xb9/0x1b3
[52174.524053] [<ffffffff8117bafa>] mount_fs+0x67/0x131
[52174.524053] [<ffffffff81193003>] vfs_kern_mount+0x6c/0xde
[52174.524053] [<ffffffff8119590f>] do_mount+0x8a6/0x9e8
[52174.524053] [<ffffffff811358dd>] ? strndup_user+0x3f/0x59
[52174.524053] [<ffffffff81195c65>] SyS_mount+0x77/0x9f
[52174.524053] [<ffffffff814935d7>] entry_SYSCALL_64_fastpath+0x12/0x6b
[52174.561288] ---[ end trace 6b53049efb1a3ea6 ]---
Fix this by forcing a transaction commit when such cases happen.
This means we check in the commit root of the subvolume tree if there
was any other inode with the same reference when the inode we are
fsync'ing is a new inode (created in the current transaction).
Test cases for fstests, covering all the scenarios given above, were
submitted upstream for fstests:
* fstests: generic test for fsync after renaming directory
https://patchwork.kernel.org/patch/8694281/
* fstests: generic test for fsync after renaming file
https://patchwork.kernel.org/patch/8694301/
* fstests: add btrfs test for fsync after snapshot deletion
https://patchwork.kernel.org/patch/8670671/
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eebb8034a5 upstream.
IOMMU drivers that do not support default domains, but make
use of the the group->domain pointer can get that pointer
overwritten with NULL on device add/remove.
Make sure this can't happen by only overwriting the domain
pointer when it is NULL.
Fixes: 1228236de5 ('iommu: Move default domain allocation to iommu_group_get_for_dev()')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c325a67c72 upstream.
Previously, ext4 would fail the mount if the file system had the quota
feature enabled and quota mount options (used for the older quota
setups) were present. This broke xfstests, since xfs silently ignores
the usrquote and grpquota mount options if they are specified. This
commit changes things so that we are consistent with xfs; having the
mount options specified is harmless, so no sense break users by
forbidding them.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit daf647d2dd upstream.
With the internal Quota feature, mke2fs creates empty quota inodes and
quota usage tracking is enabled as soon as the file system is mounted.
Since quotacheck is no longer preallocating all of the blocks in the
quota inode that are likely needed to be written to, we are now seeing
a lockdep false positive caused by needing to allocate a quota block
from inside ext4_map_blocks(), while holding i_data_sem for a data
inode. This results in this complaint:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&ei->i_data_sem);
lock(&s->s_dquot.dqio_mutex);
lock(&ei->i_data_sem);
lock(&s->s_dquot.dqio_mutex);
Google-Bug-Id: 27907753
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit de17e793b1 upstream.
If the lower or upper directory of an overlayfs mount belong to a btrfs
file system and we fsync the file through the overlayfs' merged directory
we ended up accessing an inode that didn't belong to btrfs as if it were
a btrfs inode at btrfs_sync_file() resulting in a crash like the following:
[ 7782.588845] BUG: unable to handle kernel NULL pointer dereference at 0000000000000544
[ 7782.590624] IP: [<ffffffffa030b7ab>] btrfs_sync_file+0x11b/0x3e9 [btrfs]
[ 7782.591931] PGD 4d954067 PUD 1e878067 PMD 0
[ 7782.592016] Oops: 0002 [#6] PREEMPT SMP DEBUG_PAGEALLOC
[ 7782.592016] Modules linked in: btrfs overlay ppdev crc32c_generic evdev xor raid6_pq psmouse pcspkr sg serio_raw acpi_cpufreq parport_pc parport tpm_tis i2c_piix4 tpm i2c_core processor button loop autofs4 ext4 crc16 mbcache jbd2 sr_mod cdrom sd_mod ata_generic virtio_scsi ata_piix virtio_pci libata virtio_ring virtio scsi_mod e1000 floppy [last unloaded: btrfs]
[ 7782.592016] CPU: 10 PID: 16437 Comm: xfs_io Tainted: G D 4.5.0-rc6-btrfs-next-26+ #1
[ 7782.592016] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS by qemu-project.org 04/01/2014
[ 7782.592016] task: ffff88001b8d40c0 ti: ffff880137488000 task.ti: ffff880137488000
[ 7782.592016] RIP: 0010:[<ffffffffa030b7ab>] [<ffffffffa030b7ab>] btrfs_sync_file+0x11b/0x3e9 [btrfs]
[ 7782.592016] RSP: 0018:ffff88013748be40 EFLAGS: 00010286
[ 7782.592016] RAX: 0000000080000000 RBX: ffff880133b30c88 RCX: 0000000000000001
[ 7782.592016] RDX: 0000000000000001 RSI: ffffffff8148fec0 RDI: 00000000ffffffff
[ 7782.592016] RBP: ffff88013748bec0 R08: 0000000000000001 R09: 0000000000000000
[ 7782.624248] R10: ffff88013748be40 R11: 0000000000000246 R12: 0000000000000000
[ 7782.624248] R13: 0000000000000000 R14: 00000000009305a0 R15: ffff880015e3be40
[ 7782.624248] FS: 00007fa83b9cb700(0000) GS:ffff88023ed40000(0000) knlGS:0000000000000000
[ 7782.624248] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 7782.624248] CR2: 0000000000000544 CR3: 00000001fa652000 CR4: 00000000000006e0
[ 7782.624248] Stack:
[ 7782.624248] ffffffff8108b5cc ffff88013748bec0 0000000000000246 ffff8800b005ded0
[ 7782.624248] ffff880133b30d60 8000000000000000 7fffffffffffffff 0000000000000246
[ 7782.624248] 0000000000000246 ffffffff81074f9b ffffffff8104357c ffff880015e3be40
[ 7782.624248] Call Trace:
[ 7782.624248] [<ffffffff8108b5cc>] ? arch_local_irq_save+0x9/0xc
[ 7782.624248] [<ffffffff81074f9b>] ? ___might_sleep+0xce/0x217
[ 7782.624248] [<ffffffff8104357c>] ? __do_page_fault+0x3c0/0x43a
[ 7782.624248] [<ffffffff811a2351>] vfs_fsync_range+0x8c/0x9e
[ 7782.624248] [<ffffffff811a237f>] vfs_fsync+0x1c/0x1e
[ 7782.624248] [<ffffffff811a24d6>] do_fsync+0x31/0x4a
[ 7782.624248] [<ffffffff811a2700>] SyS_fsync+0x10/0x14
[ 7782.624248] [<ffffffff81493617>] entry_SYSCALL_64_fastpath+0x12/0x6b
[ 7782.624248] Code: 85 c0 0f 85 e2 02 00 00 48 8b 45 b0 31 f6 4c 29 e8 48 ff c0 48 89 45 a8 48 8d 83 d8 00 00 00 48 89 c7 48 89 45 a0 e8 fc 43 18 e1 <f0> 41 ff 84 24 44 05 00 00 48 8b 83 58 ff ff ff 48 c1 e8 07 83
[ 7782.624248] RIP [<ffffffffa030b7ab>] btrfs_sync_file+0x11b/0x3e9 [btrfs]
[ 7782.624248] RSP <ffff88013748be40>
[ 7782.624248] CR2: 0000000000000544
[ 7782.661994] ---[ end trace 721e14960eb939bc ]---
This started happening since commit 4bacc9c923 (overlayfs: Make f_path
always point to the overlay and f_inode to the underlay) and even though
after this change we could still access the btrfs inode through
struct file->f_mapping->host or struct file->f_inode, we would end up
resulting in more similar issues later on at check_parent_dirs_for_sync()
because the dentry we got (from struct file->f_path.dentry) was from
overlayfs and not from btrfs, that is, we had no way of getting the dentry
that belonged to btrfs (we always got the dentry that belonged to
overlayfs).
The new patch from Miklos Szeredi, titled "vfs: add file_dentry()" and
recently submitted to linux-fsdevel, adds a file_dentry() API that allows
us to get the btrfs dentry from the input file and therefore being able
to fsync when the upper and lower directories belong to btrfs filesystems.
This issue has been reported several times by users in the mailing list
and bugzilla. A test case for xfstests is being submitted as well.
Fixes: 4bacc9c923 ("overlayfs: Make f_path always point to the overlay and f_inode to the underlay")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=101951
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=109791
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c0a37d4878 upstream.
EXT4 may be used as lower layer of overlayfs and accessing f_path.dentry
can lead to a crash.
Fix by replacing direct access of file->f_path.dentry with the
file_dentry() accessor, which will always return a native object.
Reported-by: Daniel Axtens <dja@axtens.net>
Fixes: 4bacc9c923 ("overlayfs: Make f_path always point to the overlay and f_inode to the underlay")
Fixes: ff978b09f9 ("ext4 crypto: move context consistency check to ext4_file_open()")
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: David Howells <dhowells@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9dd78d8c9a upstream.
In f_op->open() lock on parent is not held, so there's no guarantee that
parent dentry won't go away at any time.
Even after this patch there's no guarantee that 'dir' will stay the parent
of 'inode', but at least it won't be freed while being used.
Fixes: ff978b09f9 ("ext4 crypto: move context consistency check to ext4_file_open()")
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d43bcfef5 upstream.
This avoids potential problems caused by a race where the inode gets
renamed out from its parent directory and the parent directory is
deleted while ext4_d_revalidate() is running.
Fixes: 28b4c26396
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit be62a1a8fd upstream.
NFS may be used as lower layer of overlayfs and accessing f_path.dentry can
lead to a crash.
Fix by replacing direct access of file->f_path.dentry with the
file_dentry() accessor, which will always return a native object.
Fixes: 4bacc9c923 ("overlayfs: Make f_path always point to the overlay and f_inode to the underlay")
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Tested-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Acked-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: David Howells <dhowells@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d101a12595 upstream.
This series fixes bugs in nfs and ext4 due to 4bacc9c923 ("overlayfs:
Make f_path always point to the overlay and f_inode to the underlay").
Regular files opened on overlayfs will result in the file being opened on
the underlying filesystem, while f_path points to the overlayfs
mount/dentry.
This confuses filesystems which get the dentry from struct file and assume
it's theirs.
Add a new helper, file_dentry() [*], to get the filesystem's own dentry
from the file. This checks file->f_path.dentry->d_flags against
DCACHE_OP_REAL, and returns file->f_path.dentry if DCACHE_OP_REAL is not
set (this is the common, non-overlayfs case).
In the uncommon case it will call into overlayfs's ->d_real() to get the
underlying dentry, matching file_inode(file).
The reason we need to check against the inode is that if the file is copied
up while being open, d_real() would return the upper dentry, while the open
file comes from the lower dentry.
[*] If possible, it's better simply to use file_inode() instead.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Tested-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Reviewed-by: Trond Myklebust <trond.myklebust@primarydata.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Daniel Axtens <dja@axtens.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f08bb1e0db upstream.
During revalidate we check whether device capacity has changed before we
decide whether to output disk information or not.
The check for old capacity failed to take into account that we scaled
sdkp->capacity based on the reported logical block size. And therefore
the capacity test would always fail for devices with sectors bigger than
512 bytes and we would print several copies of the same discovery
information.
Avoid scaling sdkp->capacity and instead adjust the value on the fly
when setting the block device capacity and generating fake C/H/S
geometry.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reported-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 95e7ff0341 upstream.
For big endian platforms, reading the axes will return
invalid values.
The device stores each axis value in a 16 bit little
endian register. The driver uses regmap_read_bulk to get
the axis value, resulting in a 16 bit little endian value.
This needs to be converted to cpu endianness to work
on big endian platforms.
Fix endianness for big endian platforms by converting
the values for the axes read from little endian to
cpu.
This is also partially fixed in commit 82d8e5da1a33 ("iio:
accel: bmg160: optimize transfers in trigger handler").
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b475c59b11 upstream.
When reading gyroscope axes using iio buffers, the values
returned are always 0. In the interrupt handler, the return
value of the read operation is returned to the user instead
of the value read. Return the value read to the user.
This is also fixed in commit 82d8e5da1a33 ("iio:
accel: bmg160: optimize transfers in trigger handler").
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2215f31dc6 upstream.
For big endian platforms, reading the axes will return
invalid values.
The device stores each axis value in a 16 bit little
endian register. The driver uses regmap_read_bulk to get
the axis value, resulting in a 16 bit little endian value.
This needs to be converted to cpu endianness to work
on big endian platforms.
Fix endianness for big endian platforms by converting
the values for the axes read from little endian to
cpu.
This is also partially fixed in commit b6fb9b6d6552 ("iio:
accel: bmc150: optimize transfers in trigger handler").
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b090a98e9 upstream.
When CONFIG_IIO_TRIGGER is enabled but CONFIG_IIO_BUFFER is
not, we get a build error in the st_magn driver:
drivers/iio/magnetometer/st_magn_core.c:573:23: error: 'ST_MAGN_TRIGGER_SET_STATE' undeclared here (not in a function)
.set_trigger_state = ST_MAGN_TRIGGER_SET_STATE,
^~~~~~~~~~~~~~~~~~~~~~~~~
Apparently, this ST_MAGN_TRIGGER_SET_STATE macro was meant to
be set to NULL when the definition is not available because
st_magn_buffer.c is not compiled, but the alternative definition
was not included in the original patch. This adds it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 74f5683f35 ("iio: st_magn: Add irq trigger handling")
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1bef2c1d4e upstream.
config structure is set to 0 when updating the buffers, so by
default config->watermark will be 0. When computing the minimum
between config->watermark and the buffer->watermark or
insert_buffer-watermark, this will always be 0 regardless of the
value set by the user for the buffer.
Set as initial value for config->watermark the maximum allowed
value so that the minimum value will always be set from one of the
buffers.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Fixes: f0566c0c40 ("iio: Set device watermark based on watermark of all
attached buffers")
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 208fae5c3b upstream.
It was reported that a kernel with CONFIG_ARM_PATCH_IDIV=y stopped
booting when compiled with the upcoming gcc 6. Turns out that turning
a function address into a writable array is undefined and gcc 6 decided
it was OK to omit the store to the first word of the function while
still preserving the store to the second word.
Even though gcc 6 is now fixed to behave more coherently, it is a
mystery that gcc 4 and gcc 5 actually produce wanted code in the kernel.
And in fact the reduced test case to illustrate the issue does indeed
break with gcc < 6 as well.
In any case, let's guard the kernel against undefined compiler behavior
by hiding the nature of the array location as suggested by gcc
developers.
Reference: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=70128
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Reported-by: Marcin Juszkiewicz <mjuszkiewicz@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ddfe0858e upstream.
The patch "scsi: rescan VPD attributes" introduced a regression in which
devices that don't support VPD were being scanned for VPD attributes
anyway. This could cause issues for some devices and should be avoided
so the check for scsi_level has been moved out of scsi_add_lun and into
scsi_attach_vpd so that all callers will not scan VPD for devices that
don't support it.
[mkp: Merge fix]
Fixes: 09e2b0b146 ("scsi: rescan VPD attributes")
Suggested-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4fccb0767f upstream.
This patch fixes an issue that usbhsg_queue_done() may cause kernel
panic when dma callback is running and usb_ep_disable() is called
by interrupt handler. (Especially, we can reproduce this issue using
g_audio with usb-dmac driver.)
For example of a flow:
usbhsf_dma_complete (on tasklet)
--> usbhsf_pkt_handler (on tasklet)
--> usbhsg_queue_done (on tasklet)
*** interrupt happened and usb_ep_disable() is called ***
--> usbhsg_queue_pop (on tasklet)
Then, oops happened.
Fixes: e73a989 ("usb: renesas_usbhs: add DMAEngine support")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6490865c67 upstream.
This patch adds a code to surely disable TX IRQ of the pipe before
starting TX DMAC transfer. Otherwise, a lot of unnecessary TX IRQs
may happen in rare cases when DMAC is used.
Fixes: e73a989 ("usb: renesas_usbhs: add DMAEngine support")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a58d42c1e upstream.
The driver can access the queue simultanously
while mac80211 tears down the interface. Without
spinlock protection this could lead to corrupting
sk_buff_head and subsequently to an invalid
pointer dereference.
Fixes: ba8c3d6f16 ("mac80211: add an intermediate software queue implementation")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cf44012810 upstream.
The ieee80211_queue_stopped() expects hw queue
number but it was given raw WMM AC number instead.
This could cause frame drops and problems with
traffic in some cases - most notably if driver
doesn't map AC numbers to queue numbers 1:1 and
uses ieee80211_stop_queues() and
ieee80211_wake_queue() only without ever calling
ieee80211_wake_queues().
On ath10k it was possible to hit this problem in
the following case:
1. wlan0 uses queue 0
(ath10k maps queues per vif)
2. offchannel uses queue 15
3. queues 1-14 are unused
4. ieee80211_stop_queues()
5. ieee80211_wake_queue(q=0)
6. ieee80211_wake_queue(q=15)
(other queues are not woken up because both
driver and mac80211 know other queues are
unused)
7. ieee80211_rx_h_mesh_fwding()
8. ieee80211_select_queue_80211() returns 2
9. ieee80211_queue_stopped(q=2) returns true
10. frame is dropped (oops!)
Fixes: d3c1597b8d ("mac80211: fix forwarded mesh frame queue mapping")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d321cd014e upstream.
When joining IBSS a full scan should be initiated in order to search
for existing cell, unless the fixed_channel parameter was set.
A default channel to create the IBSS on if no cell was found is
provided as well.
However - a scan is initiated only on the default channel provided
regardless of whether ifibss->fixed_channel is set or not, with the
obvious result of the cell not joining existing IBSS cell that is
on another channel.
Fixes: 76bed0f43b ("mac80211: IBSS fix scan request")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0ef049dc11 upstream.
When CONFIG_OPTIMIZE_INLINING is set, the sta_info_insert_finish
function consumes more stack than normally, exceeding the
1024 byte limit on ARM:
net/mac80211/sta_info.c: In function 'sta_info_insert_finish':
net/mac80211/sta_info.c:561:1: error: the frame size of 1080 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
It turns out that there are two functions that put a 'struct station_info'
on the stack: __sta_info_destroy_part2 and sta_info_insert_finish, and
this structure alone requires up to 792 bytes.
Hoping that both are called rarely enough, this replaces the
on-stack structure with a dynamic allocation, which unfortunately
requires some suboptimal error handling for out-of-memory.
The __sta_info_destroy_part2 function is actually affected by the
stack usage twice because it calls cfg80211_del_sta_sinfo(), which
has another instance of struct station_info on its stack.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 98b6218388 ("mac80211/cfg80211: add station events")
Fixes: 6f7a8d26e2 ("mac80211: send statistics with delete station event")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 62b14b241c upstream.
The original hand-implemented hash-table in mac80211 couldn't result
in insertion errors, and while converting to rhashtable I evidently
forgot to check the errors.
This surfaced now only because Ben is adding many identical keys and
that resulted in hidden insertion errors.
Fixes: 7bedd0cfad ("mac80211: use rhashtable for station table")
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05dbcb4307 upstream.
The spec says: after writing 0 to device_status, the driver MUST wait
for a read of device_status to return 0 before reinitializing the
device.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2224d879c7 upstream.
As of 5a60e87603, RBD object request
allocations are made via rbd_obj_request_create() with GFP_NOIO.
However, subsequent OSD request allocations in rbd_osd_req_create*()
use GFP_ATOMIC.
With heavy page cache usage (e.g. OSDs running on same host as krbd
client), rbd_osd_req_create() order-1 GFP_ATOMIC allocations have been
observed to fail, where direct reclaim would have allowed GFP_NOIO
allocations to succeed.
Suggested-by: Vlastimil Babka <vbabka@suse.cz>
Suggested-by: Neil Brown <neilb@suse.com>
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e8e3039f5b upstream.
The au0828 dev_state is actually a bit mask. It should not be
checking with "==" but, instead, with a logic and. There are some
places where it was doing it wrong.
Fix that by replacing the dev_state set/clear/test with the
bitops.
As reviewed by Shuah:
"Looks good. Tested running bind/unbind au0828 loop for 1000 times.
Didn't see any problems and the v4l2_querycap() problem has been
fixed with this patch.
After the above test, ran bind/unbind snd_usb_audio 1000 times.
Didn't see any problems. Generated media graph and the graph
looks good."
Reviewed-by: Shuah Khan <shuahkh@osg.samsung.com>
Tested-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ed940cd274 upstream.
au0828_v4l2_close() check for dev_state == DEV_DISCONNECTED will fail to
detect the device disconnected state correctly, if au0828_v4l2_open() runs
to set the DEV_INITIALIZED bit. A loop test of bind/unbind found this bug
by increasing the likelihood of au0828_v4l2_open() occurring while unbind
is in progress. When au0828_v4l2_close() fails to detect that the device
is in disconnect state, it attempts to power down the device and fails with
the following general protection fault:
[ 260.992962] Call Trace:
[ 260.993008] [<ffffffffa0f80f0f>] ? xc5000_sleep+0x8f/0xd0 [xc5000]
[ 260.993095] [<ffffffffa0f6803c>] ? fe_standby+0x3c/0x50 [tuner]
[ 260.993186] [<ffffffffa0ef541c>] au0828_v4l2_close+0x53c/0x620 [au0828]
[ 260.993298] [<ffffffffa0d08ec0>] v4l2_release+0xf0/0x210 [videodev]
[ 260.993382] [<ffffffff81570f9c>] __fput+0x1fc/0x6c0
[ 260.993449] [<ffffffff815714ce>] ____fput+0xe/0x10
[ 260.993519] [<ffffffff8116eb83>] task_work_run+0x133/0x1f0
[ 260.993602] [<ffffffff810035d0>] exit_to_usermode_loop+0x140/0x170
[ 260.993681] [<ffffffff810061ca>] syscall_return_slowpath+0x16a/0x1a0
[ 260.993754] [<ffffffff82835fb3>] entry_SYSCALL_64_fastpath+0xa6/0xa8
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c4e5ffb6f2 upstream.
In legacy pxa builds, ie. non device-tree and platform-data only builds,
pinctrl is not yet available. As a consequence, the pinctrl gpio
direction change function is a stub, returning always success.
In the current state, the gpio driver direction function believes the
pinctrl direction change was successful, and exits without actually
changing the gpio direction.
This patch changes the logic :
- if the pinctrl direction function fails, gpio direction will report
that failure
- if the pinctrl direction function succeeds, gpio direction is changed
by the gpio driver anyway.
This is sub optimal in the pinctrl aware case, as the gpio direction
will be changed twice: once by pinctrl function and another time by
the gpio direction function.
Yet it should be acceptable in this form, as this is functional for all
pxa platforms (device-tree and platform-data), and moreover changing a
gpio direction is very very seldom, usually in machine initialization,
seldom in drivers probe, and an exception for ac97 reset bug.
Fixes: a770d94637 ("gpio: pxa: add pin control gpio direction and request")
Reported-by: Guenter Roeck <guenter@roeck-us.net>
Tested-by: Guenter Roeck <guenter@roeck-us.net>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a4f424531 upstream.
On error path of_iomap() returns NULL, hence IS_ERR() check is invalid
and may cause a NULL pointer dereference, the change fixes this
problem.
While we are here invert a device node check to simplify the code.
Fixes: 26d8cde526 ("pinctrl: freescale: imx: add shared input select reg support")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e7515ba78 upstream.
pinctrl-sun8i-a33.c (and the dts) declare only 2 interrupt banks,
where as the closely related a23 has 3 banks. This matches with the
datasheet for the A33 where only interrupt banks B and G are specified
where as the A23 has banks A, B and G.
However the A33 being the A23 derative it is means that the interrupt
configure/status io-addresses for the 2 banks it has are not changed
from the A23, iow they have the same address as if bank A was still
present. Where as the sunxi pinctrl currently tries to use the A23 bank
A addresses for bank B, since the pinctrl code does not know about the
removed bank A.
Add a irq_bank_base parameter and use this where appropriate to take
the missing bank A into account.
This fixes external interrupts not working on the A33 (tested with
an i2c touchscreen controller which uses an external interrupt).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0129801be4 upstream.
If pinctrl_provide_dummies() is used unconditionally, then the dummy
state will be used even on DT platforms when the "init" state was
intentionally left out. Instead of "default", the dummy "init" state
will then be used during probe. Thus, when probing an I2C controller on
cold boot, communication triggered by bus notifiers broke because the
pins were not initialized.
Do it like OMAP2: use the dummy state only for non-DT platforms.
Fixes: ef0eebc051 ("drivers/pinctrl: Add the concept of an "init" state")
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fa8ff601d7 upstream.
Copying the content of an MSA vector from user memory may involve TLB
faults & mapping in pages. This will fail when preemption is disabled
due to an inability to acquire mmap_sem from do_page_fault, which meant
such vector loads to unmapped pages would always fail to be emulated.
Fix this by disabling preemption later only around the updating of
vector register state.
This change does however introduce a race between performing the load
into thread context & the thread being preempted, saving its current
live context & clobbering the loaded value. This should be a rare
occureence, so optimise for the fast path by simply repeating the load if
we are preempted.
Additionally if the copy failed then the failure path was taken with
preemption left disabled, leading to the kernel typically encountering
further issues around sleeping whilst atomic. The change to where
preemption is disabled avoids this issue.
Fixes: e4aa1f153a "MIPS: MSA unaligned memory access support"
Reported-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: James Cowgill <James.Cowgill@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12345/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 14ebda3394 upstream.
Windows lets applications choose the frequency of the timer tick,
and in Windows 10 the maximum rate was changed from 1024 Hz to
2048 Hz. Unfortunately, because of the way the Windows API
works, most applications who need a higher rate than the default
64 Hz will just do
timeGetDevCaps(&tc, sizeof(tc));
timeBeginPeriod(tc.wPeriodMin);
and pick the maximum rate. This causes very high CPU usage when
playing media or games on Windows 10, even if the guest does not
actually use the CPU very much, because the frequent timer tick
causes halt_poll_ns to kick in.
There is no really good solution, especially because Microsoft
could sooner or later bump the limit to 4096 Hz, but for now
the best we can do is lower a bit the upper limit for
halt_poll_ns. :-(
Reported-by: Jon Panozzo <jonp@lime-technology.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 321c5658c5 upstream.
Non maskable interrupts (NMI) are preferred to interrupts in current
implementation. If a NMI is pending and NMI is blocked by the result
of nmi_allowed(), pending interrupt is not injected and
enable_irq_window() is not executed, even if interrupts injection is
allowed.
In old kernel (e.g. 2.6.32), schedule() is often called in NMI context.
In this case, interrupts are needed to execute iret that intends end
of NMI. The flag of blocking new NMI is not cleared until the guest
execute the iret, and interrupts are blocked by pending NMI. Due to
this, iret can't be invoked in the guest, and the guest is starved
until block is cleared by some events (e.g. canceling injection).
This patch injects pending interrupts, when it's allowed, even if NMI
is blocked. And, If an interrupts is pending after executing
inject_pending_event(), enable_irq_window() is executed regardless of
NMI pending counter.
Signed-off-by: Yuki Shibuya <shibuya.yk@ncos.nec.co.jp>
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1363074667 upstream.
Add a new NO_REPORT_LUNS quirk and set it for Seagate drives with
an usb-id of: 0bc2:331a, as these will fail to respond to a
REPORT_LUNS command.
Reported-and-tested-by: David Webb <djw@noc.ac.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3ba3458fb9 ]
When sending a UDPv6 message longer than MTU, account for the length
of fragmentable IPv6 extension headers in skb->network_header offset.
Same as we do in alloc_new_skb path in __ip6_append_data().
This ensures that later on __ip6_make_skb() will make space in
headroom for fragmentable extension headers:
/* move skb->data to ip header from ext header */
if (skb->data < skb_network_header(skb))
__skb_pull(skb, skb_network_offset(skb));
Prevents a splat due to skb_under_panic:
skbuff: skb_under_panic: text:ffffffff8143397b len:2126 put:14 \
head:ffff880005bacf50 data:ffff880005bacf4a tail:0x48 end:0xc0 dev:lo
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:104!
invalid opcode: 0000 [#1] KASAN
CPU: 0 PID: 160 Comm: reproducer Not tainted 4.6.0-rc2 #65
[...]
Call Trace:
[<ffffffff813eb7b9>] skb_push+0x79/0x80
[<ffffffff8143397b>] eth_header+0x2b/0x100
[<ffffffff8141e0d0>] neigh_resolve_output+0x210/0x310
[<ffffffff814eab77>] ip6_finish_output2+0x4a7/0x7c0
[<ffffffff814efe3a>] ip6_output+0x16a/0x280
[<ffffffff815440c1>] ip6_local_out+0xb1/0xf0
[<ffffffff814f1115>] ip6_send_skb+0x45/0xd0
[<ffffffff81518836>] udp_v6_send_skb+0x246/0x5d0
[<ffffffff8151985e>] udpv6_sendmsg+0xa6e/0x1090
[...]
Reported-by: Ji Jianwen <jiji@redhat.com>
Signed-off-by: Jakub Sitnicki <jkbs@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b6ee376cb0 ]
When creating an ip6tnl tunnel with ip tunnel, rtnl_link_ops is not set
before ip6_tnl_create2 is called. When register_netdevice is called, there
is no linkinfo attribute in the NEWLINK message because of that.
Setting rtnl_link_ops before calling register_netdevice fixes that.
Fixes: 0b11245722 ("ip6tnl: add support of link creation via rtnl")
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@redhat.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 016adb7260 ]
After commit f84bb1eac0 ("net: fix IFF_NO_QUEUE for drivers using
alloc_netdev"), default qdisc was changed to noqueue because
tuntap does not set tx_queue_len during .setup(). This patch restores
default qdisc by setting tx_queue_len in tun_setup().
Fixes: f84bb1eac0 ("net: fix IFF_NO_QUEUE for drivers using alloc_netdev")
Cc: Phil Sutter <phil@nwl.cc>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5a5abb1fa3 ]
Sasha Levin reported a suspicious rcu_dereference_protected() warning
found while fuzzing with trinity that is similar to this one:
[ 52.765684] net/core/filter.c:2262 suspicious rcu_dereference_protected() usage!
[ 52.765688] other info that might help us debug this:
[ 52.765695] rcu_scheduler_active = 1, debug_locks = 1
[ 52.765701] 1 lock held by a.out/1525:
[ 52.765704] #0: (rtnl_mutex){+.+.+.}, at: [<ffffffff816a64b7>] rtnl_lock+0x17/0x20
[ 52.765721] stack backtrace:
[ 52.765728] CPU: 1 PID: 1525 Comm: a.out Not tainted 4.5.0+ #264
[...]
[ 52.765768] Call Trace:
[ 52.765775] [<ffffffff813e488d>] dump_stack+0x85/0xc8
[ 52.765784] [<ffffffff810f2fa5>] lockdep_rcu_suspicious+0xd5/0x110
[ 52.765792] [<ffffffff816afdc2>] sk_detach_filter+0x82/0x90
[ 52.765801] [<ffffffffa0883425>] tun_detach_filter+0x35/0x90 [tun]
[ 52.765810] [<ffffffffa0884ed4>] __tun_chr_ioctl+0x354/0x1130 [tun]
[ 52.765818] [<ffffffff8136fed0>] ? selinux_file_ioctl+0x130/0x210
[ 52.765827] [<ffffffffa0885ce3>] tun_chr_ioctl+0x13/0x20 [tun]
[ 52.765834] [<ffffffff81260ea6>] do_vfs_ioctl+0x96/0x690
[ 52.765843] [<ffffffff81364af3>] ? security_file_ioctl+0x43/0x60
[ 52.765850] [<ffffffff81261519>] SyS_ioctl+0x79/0x90
[ 52.765858] [<ffffffff81003ba2>] do_syscall_64+0x62/0x140
[ 52.765866] [<ffffffff817d563f>] entry_SYSCALL64_slow_path+0x25/0x25
Same can be triggered with PROVE_RCU (+ PROVE_RCU_REPEATEDLY) enabled
from tun_attach_filter() when user space calls ioctl(tun_fd, TUN{ATTACH,
DETACH}FILTER, ...) for adding/removing a BPF filter on tap devices.
Since the fix in f91ff5b9ff ("net: sk_{detach|attach}_filter() rcu
fixes") sk_attach_filter()/sk_detach_filter() now dereferences the
filter with rcu_dereference_protected(), checking whether socket lock
is held in control path.
Since its introduction in 9940516259 ("tun: socket filter support"),
tap filters are managed under RTNL lock from __tun_chr_ioctl(). Thus the
sock_owned_by_user(sk) doesn't apply in this specific case and therefore
triggers the false positive.
Extend the BPF API with __sk_attach_filter()/__sk_detach_filter() pair
that is used by tap filters and pass in lockdep_rtnl_is_held() for the
rcu_dereference_protected() checks instead.
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5e263f7126 ]
When NET_SWITCHDEV=n, switchdev_port_attr_set will return -EOPNOTSUPP,
we should ignore this error code and continue to set the ageing time.
Fixes: c62987bbd8 ("bridge: push bridge setting ageing_time down to switchdev")
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 071d36bf21 ]
A crash is observed when a decrypted packet is processed in receive
path. get_rps_cpus() tries to dereference the skb->dev fields but it
appears that the device is freed from the poison pattern.
[<ffffffc000af58ec>] get_rps_cpu+0x94/0x2f0
[<ffffffc000af5f94>] netif_rx_internal+0x140/0x1cc
[<ffffffc000af6094>] netif_rx+0x74/0x94
[<ffffffc000bc0b6c>] xfrm_input+0x754/0x7d0
[<ffffffc000bc0bf8>] xfrm_input_resume+0x10/0x1c
[<ffffffc000ba6eb8>] esp_input_done+0x20/0x30
[<ffffffc0000b64c8>] process_one_work+0x244/0x3fc
[<ffffffc0000b7324>] worker_thread+0x2f8/0x418
[<ffffffc0000bb40c>] kthread+0xe0/0xec
-013|get_rps_cpu(
| dev = 0xFFFFFFC08B688000,
| skb = 0xFFFFFFC0C76AAC00 -> (
| dev = 0xFFFFFFC08B688000 -> (
| name =
"......................................................
| name_hlist = (next = 0xAAAAAAAAAAAAAAAA, pprev =
0xAAAAAAAAAAA
Following are the sequence of events observed -
- Encrypted packet in receive path from netdevice is queued
- Encrypted packet queued for decryption (asynchronous)
- Netdevice brought down and freed
- Packet is decrypted and returned through callback in esp_input_done
- Packet is queued again for process in network stack using netif_rx
Since the device appears to have been freed, the dereference of
skb->dev in get_rps_cpus() leads to an unhandled page fault
exception.
Fix this by holding on to device reference when queueing packets
asynchronously and releasing the reference on call back return.
v2: Make the change generic to xfrm as mentioned by Steffen and
update the title to xfrm
Suggested-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Jerome Stanislaus <jeromes@codeaurora.org>
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4cfc86f3da ]
Field fl4.flowi4_flags is not initialized in fib_compute_spec_dst()
before calling fib_lookup(), which means fib_table_lookup() is
using non-deterministic data at this line:
if (!(flp->flowi4_flags & FLOWI_FLAG_SKIP_NH_OIF)) {
Fix by initializing the entire fl4 structure, which will prevent
similar issues as fields are added in the future by ensuring that
all fields are initialized to zero unless explicitly initialized
to another value.
Fixes: 58189ca7b2 ("net: Fix vti use case with oif in dst lookups")
Suggested-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: Lance Richardson <lrichard@redhat.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ad0ea1989c ]
Currently, ingress ipv4 broadcast datagrams are dropped since,
in udp_v4_early_demux(), ip_check_mc_rcu() is invoked even on
bcast packets.
This patch addresses the issue, invoking ip_check_mc_rcu()
only for mcast packets.
Fixes: 6e54030932 ("ipv4/udp: Verify multicast group is ours in upd_v4_early_demux()")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fe30937b65 ]
bond_get_stats() can be called from rtnetlink (with RTNL held)
or from /proc/net/dev seq handler (with RCU held)
The logic added in commit 5f0c5f73e5 ("bonding: make global bonding
stats more reliable") kind of assumed only one cpu could run there.
If multiple threads are reading /proc/net/dev, stats can be really
messed up after a while.
A second problem is that some fields are 32bit, so we need to properly
handle the wrap around problem.
Given that RTNL is not always held, we need to use
bond_for_each_slave_rcu().
Fixes: 5f0c5f73e5 ("bonding: make global bonding stats more reliable")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Andy Gospodarek <gospo@cumulusnetworks.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit eee5772322 ]
When un-mapping skb->data in __bcmgenet_tx_reclaim(),
we must use the length that was used in original dma_map_single(),
instead of skb->len that might be bigger (includes the frags)
We simply can store skb_len into tx_cb_ptr->dma_len and use it
at unmap time.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2c9a266afe ]
When running small packets [length < 256 bytes] traffic, packets were
being dropped due to invalid data in those packets which were
delivered by the driver upto the stack. Using pci_dma_sync_single_for_cpu
ensures copying latest and updated data into skb from the receive buffer.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e316ea62e3 ]
Now SYN_RECV request sockets are installed in ehash table, an ICMP
handler can find a request socket while another cpu handles an incoming
packet transforming this SYN_RECV request socket into an ESTABLISHED
socket.
We need to remove the now obsolete WARN_ON(req->sk), since req->sk
is set when a new child is created and added into listener accept queue.
If this race happens, the ICMP will do nothing special.
Fixes: 079096f103 ("tcp/dccp: install syn_recv requests into ehash table")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Ben Lazarus <blazarus@google.com>
Reported-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e8e56ffd9d ]
Locking ppp_mutex must be done before dereferencing file->private_data,
otherwise it could be modified before ppp_unattached_ioctl() takes the
lock. This could lead ppp_unattached_ioctl() to override ->private_data,
thus leaking reference to the ppp_file previously pointed to.
v2: lock all ppp_ioctl() instead of just checking private_data in
ppp_unattached_ioctl(), to avoid ambiguous behaviour.
Fixes: f3ff8a4d80 ("ppp: push BKL down into the driver")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1c2722a975 ]
In the previous patch, the spinlock was not initialized. While it didn't
cause any trouble yet it could be a problem to use it uninitialized.
The most annoying part was the critical section protected by the spinlock
in mvneta_stop(). Some of the functions could sleep as pointed when
activated CONFIG_DEBUG_ATOMIC_SLEEP. Actually, in mvneta_stop() we only
need to protect the is_stopped flagged, indeed the code of the notifier
for CPU online is protected by the same spinlock, so when we get the
lock, the notifer work is done.
Reported-by: Patrick Uiterwijk <patrick@puiterwijk.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 83d6f1f15f ]
Code that was added back in 2.6.38 has an obvious overflow
when accessing a static array, and at the time it was added
only a code comment was put in front of it as a reminder
to have it reviewed properly.
This has not happened, but gcc-6 now points to the specific
overflow:
drivers/net/wireless/ath/ath9k/eeprom.c: In function 'ath9k_hw_get_gain_boundaries_pdadcs':
drivers/net/wireless/ath/ath9k/eeprom.c:483:44: error: array subscript is above array bounds [-Werror=array-bounds]
maxPwrT4[i] = data_9287[idxL].pwrPdg[i][4];
~~~~~~~~~~~~~~~~~~~~~~~~~^~~
It turns out that the correct array length exists in the local
'intercepts' variable of this function, so we can just use that
instead of hardcoding '4', so this patch changes all three
instances to use that variable. The other two instances were
already correct, but it's more consistent this way.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 940cd2c12e ("ath9k_hw: merge the ar9287 version of ath9k_hw_get_gain_boundaries_pdadcs")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e725a66c02 ]
gcc-6 finds an out of bounds access in the fst_add_one function
when calculating the end of the mmio area:
drivers/net/wan/farsync.c: In function 'fst_add_one':
drivers/net/wan/farsync.c:418:53: error: index 2 denotes an offset greater than size of 'u8[2][8192] {aka unsigned char[2][8192]}' [-Werror=array-bounds]
#define BUF_OFFSET(X) (BFM_BASE + offsetof(struct buf_window, X))
^
include/linux/compiler-gcc.h:158:21: note: in definition of macro '__compiler_offsetof'
__builtin_offsetof(a, b)
^
drivers/net/wan/farsync.c:418:37: note: in expansion of macro 'offsetof'
#define BUF_OFFSET(X) (BFM_BASE + offsetof(struct buf_window, X))
^~~~~~~~
drivers/net/wan/farsync.c:2519:36: note: in expansion of macro 'BUF_OFFSET'
+ BUF_OFFSET ( txBuffer[i][NUM_TX_BUFFER][0]);
^~~~~~~~~~
The warning is correct, but not critical because this appears
to be a write-only variable that is set by each WAN driver but
never accessed afterwards.
I'm taking the minimal fix here, using the correct pointer by
pointing 'mem_end' to the last byte inside of the register area
as all other WAN drivers do, rather than the first byte outside of
it. An alternative would be to just remove the mem_end member
entirely.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit baefd7015c ]
The implementation of QP paravirtualization back in linux-3.7 included
some code that looks very dubious, and gcc-6 has grown smart enough
to warn about it:
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c: In function 'verify_qp_parameters':
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:3154:5: error: statement is indented as if it were guarded by... [-Werror=misleading-indentation]
if (optpar & MLX4_QP_OPTPAR_ALT_ADDR_PATH) {
^~
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:3144:4: note: ...this 'if' clause, but it is not
if (slave != mlx4_master_func_num(dev))
>From looking at the context, I'm reasonably sure that the indentation
is correct but that it should have contained curly braces from the
start, as the update_gid() function in the same patch correctly does.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 54679e1482 ("mlx4: Implement QP paravirtualization and maintain phys_pkey_cache for smp_snoop")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 34b88a68f2 ]
The syzkaller fuzzer hit the following use-after-free:
Call Trace:
[<ffffffff8175ea0e>] __asan_report_load8_noabort+0x3e/0x40 mm/kasan/report.c:295
[<ffffffff851cc31a>] __sys_recvmmsg+0x6fa/0x7f0 net/socket.c:2261
[< inline >] SYSC_recvmmsg net/socket.c:2281
[<ffffffff851cc57f>] SyS_recvmmsg+0x16f/0x180 net/socket.c:2270
[<ffffffff86332bb6>] entry_SYSCALL_64_fastpath+0x16/0x7a
arch/x86/entry/entry_64.S:185
And, as Dmitry rightly assessed, that is because we can drop the
reference and then touch it when the underlying recvmsg calls return
some packets and then hit an error, which will make recvmmsg to set
sock->sk->sk_err, oops, fix it.
Reported-and-Tested-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Kostya Serebryany <kcc@google.com>
Cc: Sasha Levin <sasha.levin@oracle.com>
Fixes: a2e2725541 ("net: Introduce recvmmsg socket syscall")
http://lkml.kernel.org/r/20160122211644.GC2470@redhat.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fbd40ea018 ]
When an inetdev is destroyed, every address assigned to the interface
is removed. And in this scenerio we do two pointless things which can
be very expensive if the number of assigned interfaces is large:
1) Address promotion. We are deleting all addresses, so there is no
point in doing this.
2) A full nf conntrack table purge for every address. We only need to
do this once, as is already caught by the existing
masq_dev_notifier so masq_inet_event() can skip this.
Reported-by: Solar Designer <solar@openwall.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tested-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 88de1cd457 ]
In rocker, ageing time is a per-port attribute, so the next time the FDB
cleanup timer fires should be set according to the lowest ageing time.
This will later allow us to delete the BR_MIN_AGEING_TIME macro, which was
added to guarantee minimum ageing time in the bridge layer, thereby breaking
existing behavior.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 869f63a4d2 ]
Commit c62987bbd8 ("bridge: push bridge setting ageing_time down to
switchdev") added a check for minimum and maximum ageing time, but this
breaks existing behaviour where one can set ageing time to 0 for a
non-learning bridge.
Push this check down to the driver and allow the check in the bridge
layer to be removed. Currently ageing time 0 is refused by the driver,
but we can later add support for this functionality.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8e2ad4113c ]
The stack expects link layer headers in the skb linear section.
Macvtap can create skbs with llheader in frags in edge cases:
when (IFF_VNET_HDR is off or vnet_hdr.hdr_len < ETH_HLEN) and
prepad + len > PAGE_SIZE and vnet_hdr.flags has no or bad csum.
Add checks to ensure linear is always at least ETH_HLEN.
At this point, len is already ensured to be >= ETH_HLEN.
For backwards compatiblity, rounds up short vnet_hdr.hdr_len.
This differs from tap and packet, which return an error.
Fixes b9fb9ee07e ("macvtap: add GSO/csum offload support")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 819bfe764d ]
o While the driver is in the middle of a MB completion processing
and it receives a spurious MB interrupt, it is mistaken as a good MB
completion interrupt leading to premature completion of the next MB
request. Fix the driver to guard against this by checking the current
state of MB processing and ignore the spurious interrupt.
Also added a stats counter to record this condition.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d0ba913488 ]
Iff dma_map_single() fails, 'rxdesc' should point to the last filled RX
descriptor, so that it can be marked as the last one, however the driver
would have already advanced it by that time. In order to fix that, only
fill an RX descriptor once all the data for it is ready.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 04761890a7 ]
The initial commit badly merged into the dsa_resume method instead
of the dsa_remove_dst method.
As consequence, the dst->master_netdev->dsa_ptr is not set to NULL on
removal and re-bind of the dsa device fails with error -17.
Fixes: b0dc635d92 ("net: dsa: cleanup resources upon module removal ")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cdc4e47da8 ]
Lots of places in the kernel use memcpy(buf, comm, TASK_COMM_LEN); but
the result is typically passed to print("%s", buf) and extra bytes
after zero don't cause any harm.
In bpf the result of bpf_get_current_comm() is used as the part of
map key and was causing spurious hash map mismatches.
Use strlcpy() to guarantee zero-terminated string.
bpf verifier checks that output buffer is zero-initialized,
so even for short task names the output buffer don't have junk bytes.
Note it's not a security concern, since kprobe+bpf is root only.
Fixes: ffeedafbf0 ("bpf: introduce current->pid, tgid, uid, gid, comm accessors")
Reported-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9ed988cd59 ]
Replace link layer header validation check ll_header_truncate with
more generic dev_validate_header.
Validation based on hard_header_len incorrectly drops valid packets
in variable length protocols, such as AX25. dev_validate_header
calls header_ops.validate for such protocols to ensure correctness
below hard_header_len.
See also http://comments.gmane.org/gmane.linux.network/401064
Fixes 9c7077622d ("packet: make packet_snd fail on len smaller than l2 header")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2793a23aac ]
Netdevice parameter hard_header_len is variously interpreted both as
an upper and lower bound on link layer header length. The field is
used as upper bound when reserving room at allocation, as lower bound
when validating user input in PF_PACKET.
Clarify the definition to be maximum header length. For validation
of untrusted headers, add an optional validate member to header_ops.
Allow bypassing of validation by passing CAP_SYS_RAWIO, for instance
for deliberate testing of corrupt input. In this case, pad trailing
bytes, as some device drivers expect completely initialized headers.
See also http://comments.gmane.org/gmane.linux.network/401064
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff1e22e7a6 upstream.
Moving an unmasked irq may result in irq handler being invoked on both
source and target CPUs.
With 2-level this can happen as follows:
On source CPU:
evtchn_2l_handle_events() ->
generic_handle_irq() ->
handle_edge_irq() ->
eoi_pirq():
irq_move_irq(data);
/***** WE ARE HERE *****/
if (VALID_EVTCHN(evtchn))
clear_evtchn(evtchn);
If at this moment target processor is handling an unrelated event in
evtchn_2l_handle_events()'s loop it may pick up our event since target's
cpu_evtchn_mask claims that this event belongs to it *and* the event is
unmasked and still pending. At the same time, source CPU will continue
executing its own handle_edge_irq().
With FIFO interrupt the scenario is similar: irq_move_irq() may result
in a EVTCHNOP_unmask hypercall which, in turn, may make the event
pending on the target CPU.
We can avoid this situation by moving and clearing the event while
keeping event masked.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 72b9ff0612 upstream.
For drm_gem_object_unreference callers are required to hold
dev->struct_mutex, which these paths don't. Enforcing this requirement
has become a bit more strict with
commit ef4c6270bf
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Oct 15 09:36:25 2015 +0200
drm/gem: Check locking in drm_gem_object_unreference
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7779c5e23c upstream.
1) don't let other threads trying to bang on aux channel interrupt the
defer timeout/logic
2) don't let other threads interrupt the i2c over aux logic
Technically, according to people who actually have the DP spec, this
should not be required. In practice, it makes some troublesome Dell
monitor (and perhaps others) work, so probably a case of "It's compliant
if it works with windows" on the hw vendor's part..
v2: rebased to come before DPCD/AUX logging patch for easier backport
to stable branches.
Reported-by: Dave Wysochanski <dwysocha@redhat.com>
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1274157
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a6002ec5a8 upstream.
arm and arm64 use different config options to specify big endian. This
needs taking into account when including code/headers between the two
architectures.
A case in point is PAN, which uses the __instr_arm() macro to output
instructions. The macro comes from opcodes.h, which lives under arch/arm.
On a big-endian build the mismatched config options mean the instruction
isn't byte swapped correctly, resulting in undefined instruction exceptions
during boot:
| alternatives: patching kernel code
| kdevtmpfs[87]: undefined instruction: pc=ffffffc0004505b4
| kdevtmpfs[87]: undefined instruction: pc=ffffffc00076231c
| kdevtmpfs[87]: undefined instruction: pc=ffffffc00076231c
| kdevtmpfs[87]: undefined instruction: pc=ffffffc00076231c
| kdevtmpfs[87]: undefined instruction: pc=ffffffc00076231c
| kdevtmpfs[87]: undefined instruction: pc=ffffffc00076231c
| kdevtmpfs[87]: undefined instruction: pc=ffffffc00076231c
| kdevtmpfs[87]: undefined instruction: pc=ffffffc00076231c
| kdevtmpfs[87]: undefined instruction: pc=ffffffc00076231c
| kdevtmpfs[87]: undefined instruction: pc=ffffffc00076231c
| Internal error: Oops - undefined instruction: 0 [#1] SMP
| Modules linked in:
| CPU: 0 PID: 87 Comm: kdevtmpfs Not tainted 4.1.16+ #5
| Hardware name: Hisilicon PhosphorHi1382 EVB (DT)
| task: ffffffc336591700 ti: ffffffc3365a4000 task.ti: ffffffc3365a4000
| PC is at dump_instr+0x68/0x100
| LR is at do_undefinstr+0x1d4/0x2a4
| pc : [<ffffffc00076231c>] lr : [<ffffffc0000811d4>] pstate: 604001c5
| sp : ffffffc3365a6450
Reported-by: Hanjun Guo <guohanjun@huawei.com>
Tested-by: Xuefeng Wang <wxf.wang@hisilicon.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 95272c2937 upstream.
-ftracer can duplicate asm blocks causing compilation to fail in
noclone functions. For example, KVM declares a global variable
in an asm like
asm("2: ... \n
.pushsection data \n
.global vmx_return \n
vmx_return: .long 2b");
and -ftracer causes a double declaration.
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Michal Marek <mmarek@suse.cz>
Cc: kvm@vger.kernel.org
Reported-by: Linda Walsh <lkml@tlinx.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 01d7c2a2de upstream.
In save_sprs() in process.c contains the following test:
if (cpu_has_feature(cpu_has_feature(CPU_FTR_ALTIVEC)))
t->vrsave = mfspr(SPRN_VRSAVE);
CPU feature with the mask 0x1 is CPU_FTR_COHERENT_ICACHE so the test
is equivilent to:
if (cpu_has_feature(CPU_FTR_ALTIVEC) &&
cpu_has_feature(CPU_FTR_COHERENT_ICACHE))
On CPUs without support for both (i.e G5) this results in vrsave not
being saved between context switches. The vector register save/restore
code doesn't use VRSAVE to determine which registers to save/restore,
but the value of VRSAVE is used to determine if altivec is being used
in several code paths.
Fixes: 152d523e63 ("powerpc: Create context switch helpers save_sprs() and restore_sprs()")
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e5670563f5 upstream.
If we detect a namespace has a stale info block in the init path, we
should overwrite with the latest configuration. In fact, we already
return -ENODEV when the parent uuid is invalid, the same should be done
for the 'self' uuid. Otherwise we can get into a condition where
userspace is unable to reconfigure the pfn-device without directly /
manually invalidating the info block.
Reported-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2112911266 upstream.
It appears that smart data retrieval has been broken the since the
initial implementation. Fix the payload size to be 128-bytes per the
specification.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc897c95e9 upstream.
With the THP refcounting rework it is possible to see THP compound tail
pages mapped with PTEs during a THP split. This needs to be considered
when using page_cache_get_speculative(), which will always fail on tail
pages because ->_count is always zero. commit 7aef4172 "mm: handle
PTE-mapped tail pages in gerneric fast gup implementaiton" fixed it for
the generic fast gup code by using compound_head(page) instead of page,
but not for s390.
This patch is a 1:1 adaption of commit 7aef4172 for the s390 fast gup
code. Without this fix, gup will fall back to the slow path or fail
in the unlikely scenario that we hit a THP under splitting in-between
the page table split and the compound page split.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 08a5bb2921 upstream.
hugepd_free() used __get_cpu_var() once. Nothing ensured that the code
accessing the variable did not migrate from one CPU to another and soon
this was noticed by Tiejun Chen in 94b09d7554 ("powerpc/hugetlb:
Replace __get_cpu_var with get_cpu_var"). So we had it fixed.
Christoph Lameter was doing his __get_cpu_var() replaces and forgot
PowerPC. Then he noticed this and sent his fixed up batch again which
got applied as 69111bac42 ("powerpc: Replace __get_cpu_var uses").
The careful reader will noticed one little detail: get_cpu_var() got
replaced with this_cpu_ptr(). So now we have a put_cpu_var() which does
a preempt_enable() and nothing that does preempt_disable() so we
underflow the preempt counter.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Christoph Lameter <cl@linux.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a07083ed6 upstream.
ALSA system timer backend stops the timer via del_timer() without sync
and leaves del_timer_sync() at the close instead. This is because of
the restriction by the design of ALSA timer: namely, the stop callback
may be called from the timer handler, and calling the sync shall lead
to a hangup. However, this also triggers a kernel BUG() when the
timer is rearmed immediately after stopping without sync:
kernel BUG at kernel/time/timer.c:966!
Call Trace:
<IRQ>
[<ffffffff8239c94e>] snd_timer_s_start+0x13e/0x1a0
[<ffffffff8239e1f4>] snd_timer_interrupt+0x504/0xec0
[<ffffffff8122fca0>] ? debug_check_no_locks_freed+0x290/0x290
[<ffffffff8239ec64>] snd_timer_s_function+0xb4/0x120
[<ffffffff81296b72>] call_timer_fn+0x162/0x520
[<ffffffff81296add>] ? call_timer_fn+0xcd/0x520
[<ffffffff8239ebb0>] ? snd_timer_interrupt+0xec0/0xec0
....
It's the place where add_timer() checks the pending timer. It's clear
that this may happen after the immediate restart without sync in our
cases.
So, the workaround here is just to use mod_timer() instead of
add_timer(). This looks like a band-aid fix, but it's a right move,
as snd_timer_interrupt() takes care of the continuous rearm of timer.
Reported-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2ef4dfd9d9 upstream.
Handling exceptions from modules never worked on parisc.
It was just masked by the fact that exceptions from modules
don't happen during normal use.
When a module triggers an exception in get_user() we need to load the
main kernel dp value before accessing the exception_data structure, and
afterwards restore the original dp value of the module on exit.
Noticed-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef72f3110d upstream.
The kernel module testcase (lib/test_user_copy.c) exhibited a kernel
crash on parisc if the parameters for copy_from_user were reversed
("illegal reversed copy_to_user" testcase).
Fix this potential crash by checking the fault handler if the faulting
address is in the exception table.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e3893027a3 upstream.
We want to avoid the kernel module loader to create function pointers
for the kernel fixup routines of get_user() and put_user(). Changing
the external reference from function type to int type fixes this.
This unbreaks exception handling for get_user() and put_user() when
called from a kernel module.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 910cd32e55 upstream.
The seccomp filter support requires careful handling of task registers. This
includes reloading of the return value (%r28) and proper syscall exit if
secure_computing() returned -1.
Additionally we need to sign-extend the syscall number from signed 32bit to
signed 64bit in do_syscall_trace_enter() since the ptrace interface only allows
storing 32bit values in compat mode.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e54358915d upstream.
Despite what the DocBook comment to pkcs7_validate_trust() says, the
*_trusted argument is never set to false.
pkcs7_validate_trust() only positively sets *_trusted upon encountering
a trusted PKCS#7 SignedInfo block.
This is quite unfortunate since its callers, system_verify_data() for
example, depend on pkcs7_validate_trust() clearing *_trusted on non-trust.
Indeed, UBSAN splats when attempting to load the uninitialized local
variable 'trusted' from system_verify_data() in pkcs7_validate_trust():
UBSAN: Undefined behaviour in crypto/asymmetric_keys/pkcs7_trust.c:194:14
load of value 82 is not a valid value for type '_Bool'
[...]
Call Trace:
[<ffffffff818c4d35>] dump_stack+0xbc/0x117
[<ffffffff818c4c79>] ? _atomic_dec_and_lock+0x169/0x169
[<ffffffff8194113b>] ubsan_epilogue+0xd/0x4e
[<ffffffff819419fa>] __ubsan_handle_load_invalid_value+0x111/0x158
[<ffffffff819418e9>] ? val_to_string.constprop.12+0xcf/0xcf
[<ffffffff818334a4>] ? x509_request_asymmetric_key+0x114/0x370
[<ffffffff814b83f0>] ? kfree+0x220/0x370
[<ffffffff818312c2>] ? public_key_verify_signature_2+0x32/0x50
[<ffffffff81835e04>] pkcs7_validate_trust+0x524/0x5f0
[<ffffffff813c391a>] system_verify_data+0xca/0x170
[<ffffffff813c3850>] ? top_trace_array+0x9b/0x9b
[<ffffffff81510b29>] ? __vfs_read+0x279/0x3d0
[<ffffffff8129372f>] mod_verify_sig+0x1ff/0x290
[...]
The implication is that pkcs7_validate_trust() effectively grants trust
when it really shouldn't have.
Fix this by explicitly setting *_trusted to false at the very beginning
of pkcs7_validate_trust().
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c2e2266a5 upstream.
arm:pxa_defconfig can result in the following crash if the max1111 driver
is not instantiated.
Unhandled fault: page domain fault (0x01b) at 0x00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: : 1b [#1] PREEMPT ARM
Modules linked in:
CPU: 0 PID: 300 Comm: kworker/0:1 Not tainted 4.5.0-01301-g1701f680407c #10
Hardware name: SHARP Akita
Workqueue: events sharpsl_charge_toggle
task: c390a000 ti: c391e000 task.ti: c391e000
PC is at max1111_read_channel+0x20/0x30
LR is at sharpsl_pm_pxa_read_max1111+0x2c/0x3c
pc : [<c03aaab0>] lr : [<c0024b50>] psr: 20000013
...
[<c03aaab0>] (max1111_read_channel) from [<c0024b50>]
(sharpsl_pm_pxa_read_max1111+0x2c/0x3c)
[<c0024b50>] (sharpsl_pm_pxa_read_max1111) from [<c00262e0>]
(spitzpm_read_devdata+0x5c/0xc4)
[<c00262e0>] (spitzpm_read_devdata) from [<c0024094>]
(sharpsl_check_battery_temp+0x78/0x110)
[<c0024094>] (sharpsl_check_battery_temp) from [<c0024f9c>]
(sharpsl_charge_toggle+0x48/0x110)
[<c0024f9c>] (sharpsl_charge_toggle) from [<c004429c>]
(process_one_work+0x14c/0x48c)
[<c004429c>] (process_one_work) from [<c0044618>] (worker_thread+0x3c/0x5d4)
[<c0044618>] (worker_thread) from [<c004a238>] (kthread+0xd0/0xec)
[<c004a238>] (kthread) from [<c000a670>] (ret_from_fork+0x14/0x24)
This can occur because the SPI controller driver (SPI_PXA2XX) is built as
module and thus not necessarily loaded. While building SPI_PXA2XX into the
kernel would make the problem disappear, it appears prudent to ensure that
the driver is instantiated before accessing its data structures.
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c3d266c8a9 upstream.
This patch tries to fix a PEBS warning found in my stress test. The
following perf command can easily trigger the pebs warning or spurious
NMI error on Skylake/Broadwell/Haswell platforms:
sudo perf record -e 'cpu/umask=0x04,event=0xc4/pp,cycles,branches,ref-cycles,cache-misses,cache-references' --call-graph fp -b -c1000 -a
Also the NMI watchdog must be enabled.
For this case, the events number is larger than counter number. So
perf has to do multiplexing.
In perf_mux_hrtimer_handler, it does perf_pmu_disable(), schedule out
old events, rotate_ctx, schedule in new events and finally
perf_pmu_enable().
If the old events include precise event, the MSR_IA32_PEBS_ENABLE
should be cleared when perf_pmu_disable(). The MSR_IA32_PEBS_ENABLE
should keep 0 until the perf_pmu_enable() is called and the new event is
precise event.
However, there is a corner case which could restore PEBS_ENABLE to
stale value during the above period. In perf_pmu_disable(), GLOBAL_CTRL
will be set to 0 to stop overflow and followed PMI. But there may be
pending PMI from an earlier overflow, which cannot be stopped. So even
GLOBAL_CTRL is cleared, the kernel still be possible to get PMI. At
the end of the PMI handler, __intel_pmu_enable_all() will be called,
which will restore the stale values if old events haven't scheduled
out.
Once the stale pebs value is set, it's impossible to be corrected if
the new events are non-precise. Because the pebs_enabled will be set
to 0. x86_pmu.enable_all() will ignore the MSR_IA32_PEBS_ENABLE
setting. As a result, the following NMI with stale PEBS_ENABLE
trigger pebs warning.
The pending PMI after enabled=0 will become harmless if the NMI handler
does not change the state. This patch checks cpuc->enabled in pmi and
only restore the state when PMU is active.
Here is the dump:
Call Trace:
<NMI> [<ffffffff813c3a2e>] dump_stack+0x63/0x85
[<ffffffff810a46f2>] warn_slowpath_common+0x82/0xc0
[<ffffffff810a483a>] warn_slowpath_null+0x1a/0x20
[<ffffffff8100fe2e>] intel_pmu_drain_pebs_nhm+0x2be/0x320
[<ffffffff8100caa9>] intel_pmu_handle_irq+0x279/0x460
[<ffffffff810639b6>] ? native_write_msr_safe+0x6/0x40
[<ffffffff811f290d>] ? vunmap_page_range+0x20d/0x330
[<ffffffff811f2f11>] ? unmap_kernel_range_noflush+0x11/0x20
[<ffffffff8148379f>] ? ghes_copy_tofrom_phys+0x10f/0x2a0
[<ffffffff814839c8>] ? ghes_read_estatus+0x98/0x170
[<ffffffff81005a7d>] perf_event_nmi_handler+0x2d/0x50
[<ffffffff810310b9>] nmi_handle+0x69/0x120
[<ffffffff810316f6>] default_do_nmi+0xe6/0x100
[<ffffffff810317f2>] do_nmi+0xe2/0x130
[<ffffffff817aea71>] end_repeat_nmi+0x1a/0x1e
[<ffffffff810639b6>] ? native_write_msr_safe+0x6/0x40
[<ffffffff810639b6>] ? native_write_msr_safe+0x6/0x40
[<ffffffff810639b6>] ? native_write_msr_safe+0x6/0x40
<<EOE>> <IRQ> [<ffffffff81006df8>] ? x86_perf_event_set_period+0xd8/0x180
[<ffffffff81006eec>] x86_pmu_start+0x4c/0x100
[<ffffffff8100722d>] x86_pmu_enable+0x28d/0x300
[<ffffffff811994d7>] perf_pmu_enable.part.81+0x7/0x10
[<ffffffff8119cb70>] perf_mux_hrtimer_handler+0x200/0x280
[<ffffffff8119c970>] ? __perf_install_in_context+0xc0/0xc0
[<ffffffff8110f92d>] __hrtimer_run_queues+0xfd/0x280
[<ffffffff811100d8>] hrtimer_interrupt+0xa8/0x190
[<ffffffff81199080>] ? __perf_read_group_add.part.61+0x1a0/0x1a0
[<ffffffff81051bd8>] local_apic_timer_interrupt+0x38/0x60
[<ffffffff817af01d>] smp_apic_timer_interrupt+0x3d/0x50
[<ffffffff817ad15c>] apic_timer_interrupt+0x8c/0xa0
<EOI> [<ffffffff81199080>] ? __perf_read_group_add.part.61+0x1a0/0x1a0
[<ffffffff81123de5>] ? smp_call_function_single+0xd5/0x130
[<ffffffff81123ddb>] ? smp_call_function_single+0xcb/0x130
[<ffffffff81199080>] ? __perf_read_group_add.part.61+0x1a0/0x1a0
[<ffffffff8119765a>] event_function_call+0x10a/0x120
[<ffffffff8119c660>] ? ctx_resched+0x90/0x90
[<ffffffff811971e0>] ? cpu_clock_event_read+0x30/0x30
[<ffffffff811976d0>] ? _perf_event_disable+0x60/0x60
[<ffffffff8119772b>] _perf_event_enable+0x5b/0x70
[<ffffffff81197388>] perf_event_for_each_child+0x38/0xa0
[<ffffffff811976d0>] ? _perf_event_disable+0x60/0x60
[<ffffffff811a0ffd>] perf_ioctl+0x12d/0x3c0
[<ffffffff8134d855>] ? selinux_file_ioctl+0x95/0x1e0
[<ffffffff8124a3a1>] do_vfs_ioctl+0xa1/0x5a0
[<ffffffff81036d29>] ? sched_clock+0x9/0x10
[<ffffffff8124a919>] SyS_ioctl+0x79/0x90
[<ffffffff817ac4b2>] entry_SYSCALL_64_fastpath+0x1a/0xa4
---[ end trace aef202839fe9a71d ]---
Uhhuh. NMI received for unknown reason 2d on CPU 2.
Do you have a strange power saving mode enabled?
Signed-off-by: Kan Liang <kan.liang@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: http://lkml.kernel.org/r/1457046448-6184-1-git-send-email-kan.liang@intel.com
[ Fixed various typos and other small details. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8077eca079 upstream.
This patch fixes an issue with the GLOBAL_OVERFLOW_STATUS bits on
Haswell, Broadwell and Skylake processors when using PEBS.
The SDM stipulates that when the PEBS iterrupt threshold is crossed,
an interrupt is posted and the kernel is interrupted. The kernel will
find GLOBAL_OVF_SATUS bit 62 set indicating there are PEBS records to
drain. But the bits corresponding to the actual counters should NOT be
set. The kernel follows the SDM and assumes that all PEBS events are
processed in the drain_pebs() callback. The kernel then checks for
remaining overflows on any other (non-PEBS) events and processes these
in the for_each_bit_set(&status) loop.
As it turns out, under certain conditions on HSW and later processors,
on PEBS buffer interrupt, bit 62 is set but the counter bits may be
set as well. In that case, the kernel drains PEBS and generates
SAMPLES with the EXACT tag, then it processes the counter bits, and
generates normal (non-EXACT) SAMPLES.
I ran into this problem by trying to understand why on HSW sampling on
a PEBS event was sometimes returning SAMPLES without the EXACT tag.
This should not happen on user level code because HSW has the
eventing_ip which always point to the instruction that caused the
event.
The workaround in this patch simply ensures that the bits for the
counters used for PEBS events are cleared after the PEBS buffer has
been drained. With this fix 100% of the PEBS samples on my user code
report the EXACT tag.
Before:
$ perf record -e cpu/event=0xd0,umask=0x81/upp ./multichase
$ perf report -D | fgrep SAMPLES
PERF_RECORD_SAMPLE(IP, 0x2): 11775/11775: 0x406de5 period: 73469 addr: 0 exact=Y
\--- EXACT tag is missing
After:
$ perf record -e cpu/event=0xd0,umask=0x81/upp ./multichase
$ perf report -D | fgrep SAMPLES
PERF_RECORD_SAMPLE(IP, 0x4002): 11775/11775: 0x406de5 period: 73469 addr: 0 exact=Y
\--- EXACT tag is set
The problem tends to appear more often when multiple PEBS events are used.
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: adrian.hunter@intel.com
Cc: kan.liang@intel.com
Cc: namhyung@kernel.org
Link: http://lkml.kernel.org/r/1457034642-21837-3-git-send-email-eranian@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9532e69b8 upstream.
On CPU hotplug the steal time accounting can keep a stale rq->prev_steal_time
value over CPU down and up. So after the CPU comes up again the delta
calculation in steal_account_process_tick() wreckages itself due to the
unsigned math:
u64 steal = paravirt_steal_clock(smp_processor_id());
steal -= this_rq()->prev_steal_time;
So if steal is smaller than rq->prev_steal_time we end up with an insane large
value which then gets added to rq->prev_steal_time, resulting in a permanent
wreckage of the accounting. As a consequence the per CPU stats in /proc/stat
become stale.
Nice trick to tell the world how idle the system is (100%) while the CPU is
100% busy running tasks. Though we prefer realistic numbers.
None of the accounting values which use a previous value to account for
fractions is reset at CPU hotplug time. update_rq_clock_task() has a sanity
check for prev_irq_time and prev_steal_time_rq, but that sanity check solely
deals with clock warps and limits the /proc/stat visible wreckage. The
prev_time values are still wrong.
Solution is simple: Reset rq->prev_*_time when the CPU is plugged in again.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Glauber Costa <glommer@parallels.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Fixes: commit 095c0aa83e "sched: adjust scheduler cpu power for stolen time"
Fixes: commit aa48380851 "sched: Remove irq time from available CPU power"
Fixes: commit e6e6685acc "KVM guest: Steal time accounting"
Link: http://lkml.kernel.org/r/alpine.DEB.2.11.1603041539490.3686@nanos
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 276142730c upstream.
When suspending to RAM, waking up and later suspending to disk,
we gratuitously runtime resume devices after the thaw phase.
This does not occur if we always suspend to RAM or always to disk.
pm_complete_with_resume_check(), which gets called from
pci_pm_complete() among others, schedules a runtime resume
if PM_SUSPEND_FLAG_FW_RESUME is set. The flag is set during
a suspend-to-RAM cycle. It is cleared at the beginning of
the suspend-to-RAM cycle but not afterwards and it is not
cleared during a suspend-to-disk cycle at all. Fix it.
Fixes: ef25ba0476 (PM / sleep: Add flags to indicate platform firmware involvement)
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d70e28f57e upstream.
Some SKL-H configurations require "intel_idle.max_cstate=7" to boot.
While that is an effective workaround, it disables C10.
This patch detects the problematic configuration,
and disables C8 and C9, keeping C10 enabled.
Note that enabling SGX in BIOS SETUP can also prevent this issue,
if the system BIOS provides that option.
https://bugzilla.kernel.org/show_bug.cgi?id=109081
"Freezes with Intel i7 6700HQ (Skylake), unless intel_idle.max_cstate=7"
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e64c29e98 upstream.
Commit 5942ddbc50 ("mtd: introduce mtd_block_markbad interface")
incorrectly changed onenand_block_markbad() to call mtd_block_markbad
instead of onenand_chip's block_markbad function. As a result the function
will now recurse and deadlock. Fix by reverting the change.
Fixes: 5942ddbc50 ("mtd: introduce mtd_block_markbad interface")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d9dddbf556 upstream.
Hanjun Guo has reported that a CMA stress test causes broken accounting of
CMA and free pages:
> Before the test, I got:
> -bash-4.3# cat /proc/meminfo | grep Cma
> CmaTotal: 204800 kB
> CmaFree: 195044 kB
>
>
> After running the test:
> -bash-4.3# cat /proc/meminfo | grep Cma
> CmaTotal: 204800 kB
> CmaFree: 6602584 kB
>
> So the freed CMA memory is more than total..
>
> Also the the MemFree is more than mem total:
>
> -bash-4.3# cat /proc/meminfo
> MemTotal: 16342016 kB
> MemFree: 22367268 kB
> MemAvailable: 22370528 kB
Laura Abbott has confirmed the issue and suspected the freepage accounting
rewrite around 3.18/4.0 by Joonsoo Kim. Joonsoo had a theory that this is
caused by unexpected merging between MIGRATE_ISOLATE and MIGRATE_CMA
pageblocks:
> CMA isolates MAX_ORDER aligned blocks, but, during the process,
> partialy isolated block exists. If MAX_ORDER is 11 and
> pageblock_order is 9, two pageblocks make up MAX_ORDER
> aligned block and I can think following scenario because pageblock
> (un)isolation would be done one by one.
>
> (each character means one pageblock. 'C', 'I' means MIGRATE_CMA,
> MIGRATE_ISOLATE, respectively.
>
> CC -> IC -> II (Isolation)
> II -> CI -> CC (Un-isolation)
>
> If some pages are freed at this intermediate state such as IC or CI,
> that page could be merged to the other page that is resident on
> different type of pageblock and it will cause wrong freepage count.
This was supposed to be prevented by CMA operating on MAX_ORDER blocks,
but since it doesn't hold the zone->lock between pageblocks, a race
window does exist.
It's also likely that unexpected merging can occur between
MIGRATE_ISOLATE and non-CMA pageblocks. This should be prevented in
__free_one_page() since commit 3c605096d3 ("mm/page_alloc: restrict
max order of merging on isolated pageblock"). However, we only check
the migratetype of the pageblock where buddy merging has been initiated,
not the migratetype of the buddy pageblock (or group of pageblocks)
which can be MIGRATE_ISOLATE.
Joonsoo has suggested checking for buddy migratetype as part of
page_is_buddy(), but that would add extra checks in allocator hotpath
and bloat-o-meter has shown significant code bloat (the function is
inline).
This patch reduces the bloat at some expense of more complicated code.
The buddy-merging while-loop in __free_one_page() is initially bounded
to pageblock_border and without any migratetype checks. The checks are
placed outside, bumping the max_order if merging is allowed, and
returning to the while-loop with a statement which can't be possibly
considered harmful.
This fixes the accounting bug and also removes the arguably weird state
in the original commit 3c605096d3 where buddies could be left
unmerged.
Fixes: 3c605096d3 ("mm/page_alloc: restrict max order of merging on isolated pageblock")
Link: https://lkml.org/lkml/2016/3/2/280
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Reported-by: Hanjun Guo <guohanjun@huawei.com>
Tested-by: Hanjun Guo <guohanjun@huawei.com>
Acked-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Debugged-by: Laura Abbott <labbott@redhat.com>
Debugged-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit be12b299a8 upstream.
When master handles convert request, it queues ast first and then
returns status. This may happen that the ast is sent before the request
status because the above two messages are sent by two threads. And
right after the ast is sent, if master down, it may trigger BUG in
dlm_move_lockres_to_recovery_list in the requested node because ast
handler moves it to grant list without clear lock->convert_pending. So
remove BUG_ON statement and check if the ast is processed in
dlmconvert_remote.
Signed-off-by: Joseph Qi <joseph.qi@huawei.com>
Reported-by: Yiwen Jiang <jiangyiwen@huawei.com>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Tariq Saeed <tariq.x.saeed@oracle.com>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ac7cf246df upstream.
There is a race window between dlmconvert_remote and
dlm_move_lockres_to_recovery_list, which will cause a lock with
OCFS2_LOCK_BUSY in grant list, thus system hangs.
dlmconvert_remote
{
spin_lock(&res->spinlock);
list_move_tail(&lock->list, &res->converting);
lock->convert_pending = 1;
spin_unlock(&res->spinlock);
status = dlm_send_remote_convert_request();
>>>>>> race window, master has queued ast and return DLM_NORMAL,
and then down before sending ast.
this node detects master down and calls
dlm_move_lockres_to_recovery_list, which will revert the
lock to grant list.
Then OCFS2_LOCK_BUSY won't be cleared as new master won't
send ast any more because it thinks already be authorized.
spin_lock(&res->spinlock);
lock->convert_pending = 0;
if (status != DLM_NORMAL)
dlm_revert_pending_convert(res, lock);
spin_unlock(&res->spinlock);
}
In this case, check if res->state has DLM_LOCK_RES_RECOVERING bit set
(res is still in recovering) or res master changed (new master has
finished recovery), reset the status to DLM_RECOVERING, then it will
retry convert.
Signed-off-by: Joseph Qi <joseph.qi@huawei.com>
Reported-by: Yiwen Jiang <jiangyiwen@huawei.com>
Reviewed-by: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Tariq Saeed <tariq.x.saeed@oracle.com>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 950336ba3e upstream.
The ati_remote2 driver expects at least two interfaces with one
endpoint each. If given malicious descriptor that specify one
interface or no endpoints, it will crash in the probe function.
Ensure there is at least two interfaces and one endpoint for each
interface before using it.
The full disclosure: http://seclists.org/bugtraq/2016/Mar/90
Reported-by: Ralf Spenneberg <ralf@spenneberg.net>
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aaf2559332 upstream.
When cgroup writeback is in use, there can be multiple wb's
(bdi_writeback's) per bdi and an inode may switch among them
dynamically. In a couple places, the wrong wb was used leading to
performing operations on the wrong list under the wrong lock
corrupting the io lists.
* writeback_single_inode() was taking @wb parameter and used it to
remove the inode from io lists if it becomes clean after writeback.
The callers of this function were always passing in the root wb
regardless of the actual wb that the inode was associated with,
which could also change while writeback is in progress.
Fix it by dropping the @wb parameter and using
inode_to_wb_and_lock_list() to determine and lock the associated wb.
* After writeback_sb_inodes() writes out an inode, it re-locks @wb and
inode to remove it from or move it to the right io list. It assumes
that the inode is still associated with @wb; however, the inode may
have switched to another wb while writeback was in progress.
Fix it by using inode_to_wb_and_lock_list() to determine and lock
the associated wb after writeback is complete. As the function
requires the original @wb->list_lock locked for the next iteration,
in the unlikely case where the inode has changed association, switch
the locks.
Kudos to Tahsin for pinpointing these subtle breakages.
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: d10c809552 ("writeback: implement foreign cgroup inode bdi_writeback switching")
Link: http://lkml.kernel.org/g/CAAeU0aMYeM_39Y2+PaRvyB1nqAPYZSNngJ1eBRmrxn7gKAt2Mg@mail.gmail.com
Reported-and-diagnosed-by: Tahsin Erdogan <tahsin@google.com>
Tested-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 614a4e3773 upstream.
locked_inode_to_wb_and_lock_list() wb_get()'s the wb associated with
the target inode, unlocks inode, locks the wb's list_lock and verifies
that the inode is still associated with the wb. To prevent the wb
going away between dropping inode lock and acquiring list_lock, the wb
is pinned while inode lock is held. The wb reference is put right
after acquiring list_lock citing that the wb won't be dereferenced
anymore.
This isn't true. If the inode is still associated with the wb, the
inode has reference and it's safe to return the wb; however, if inode
has been switched, the wb still needs to be unlocked which is a
dereference and can lead to use-after-free if it it races with wb
destruction.
Fix it by putting the reference after releasing list_lock.
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: 87e1d789bf ("writeback: implement [locked_]inode_to_wb_and_lock_list()")
Tested-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fbda4b38fa upstream.
Commit 58a1fbbb2e ("PM / PCI / ACPI: Kick devices that might have been
reset by firmware") added a runtime resume for devices that were runtime
suspended when the system entered suspend-to-RAM.
Briefly, the motivation was to ensure that devices did not remain in a
reset-power-on state after resume, potentially preventing deep SoC-wide
low-power states from being entered on idle.
Currently we're not doing the same when leaving suspend-to-disk and this
asymmetry is a problem if drivers rely on the automatic resume triggered
by pm_complete_with_resume_check(). Fix it.
Fixes: 58a1fbbb2e (PM / PCI / ACPI: Kick devices that might have been reset by firmware)
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b02acd4e62 upstream.
If enabling the hsmci regulator on card detection, the board can reboot
on sd card insertion. Keeping the regulator always enabled fixes this
issue.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: 8d545f32bd ("ARM: at91/dt: sama5d4 xplained: add regulators for v(q)mmc1 supplies")
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ae3fc8ea08 upstream.
If enabling the hsmci regulator on card detection, the board can reboot
on sd card insertion. Keeping the regulator always enabled fixes this
issue.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: 1b53e3416d ("ARM: at91/dt: sama5d3 xplained: add fixed regulator for vmmc0")
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f6fc056e8 upstream.
nfsd_lookup_dentry exits with the parent filehandle locked. fh_put also
unlocks if necessary (nfsd filehandle locking is probably too lenient),
so it gets unlocked eventually, but if the following op in the compound
needs to lock it again, we can deadlock.
A fuzzer ran into this; normal clients don't send a secinfo followed by
a readdir in the same compound.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4aed9c46af upstream.
A number of spots in the xdr decoding follow a pattern like
n = be32_to_cpup(p++);
READ_BUF(n + 4);
where n is a u32. The only bounds checking is done in READ_BUF itself,
but since it's checking (n + 4), it won't catch cases where n is very
large, (u32)(-4) or higher. I'm not sure exactly what the consequences
are, but we've seen crashes soon after.
Instead, just break these up into two READ_BUF()s.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6d1fba0c2c upstream.
When we receive an event that triggers connection termination,
we have a a couple of things we may want to do:
1. In case we are already terminating, bailout early
2. In case we are connected but not bound, disconnect and schedule
a connection cleanup silently (don't reinstate)
3. In case we are connected and bound, disconnect and reinstate the connection
This rework fixes a bug that was detected against a mis-behaved
initiator which rejected our rdma_cm accept, in this stage the
isert_conn is no bound and reinstate caused a bogus dereference.
What's great about this is that we don't need the
post_recv_buf_count anymore, so get rid of it.
Signed-off-by: Jenny Derzhavetz <jennyf@mellanox.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aea9298060 upstream.
We need an indication that isert_conn->iscsi_conn binding has
happened so we'll know not to invoke a connection reinstatement
on an unbound connection which will lead to a bogus isert_conn->conn
dereferece.
Signed-off-by: Jenny Derzhavetz <jennyf@mellanox.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b89a7c2546 upstream.
Once connection request is accepted, one rx descriptor
is posted to receive login request. This descriptor has rx type,
but is outside the main pool of rx descriptors, and thus
was mistreated as tx type.
Signed-off-by: Jenny Derzhavetz <jennyf@mellanox.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e47f1985d upstream.
This patch fixes an active I/O shutdown bug for fabric
drivers using target_wait_for_sess_cmds(), where se_cmd
descriptor shutdown would result in hung tasks waiting
indefinitely for se_cmd->cmd_wait_comp to complete().
To address this bug, drop the incorrect list_del_init()
usage in target_wait_for_sess_cmds() and always complete()
during se_cmd target_release_cmd_kref() put, in order to
let caller invoke the final fabric release callback
into se_cmd->se_tfo->release_cmd() code.
Reported-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Tested-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 773b3966dd upstream.
Our dividers weren't being set successfully because CM_PASSWORD wasn't
included in the register write. It looks easier to just compute the
divider to write ourselves than to update clk-divider for the ability
to OR in some arbitrary bits on write.
Fixes about half of the video modes on my HDMI monitor (everything
except 720x400).
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e8b63288b3 upstream.
hclk_cpubus needs to keep running because it is needed for devices like
the rom, i2s0 or spdif to be accessible via cpu. Without that all
accesses to devices (readl/writel) return wrong data. So add it
to the list of critical clocks.
Fixes: 78eaf6095c ("clk: rockchip: disable unused clocks")
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f28d98463 upstream.
The vdpu and vepu clocks can also be parented to the npll and current
parent list also is wrong as it would use the npll as "usbphy" source,
so adapt the parent to the correct one.
Fixes: 3536c97a52 ("clk: rockchip: add rk3368 clock controller")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: zhangqing <zhangqing@rock-chips.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c6d5fe2ca8 upstream.
Similar to commit 9880d4277f ("clk: rockchip: fix rk3288 cpuclk core
dividers") it seems the cpuclk dividers are one to high on the rk3368
as well.
And again similar to the previous fix, we opt to make the divider list
contain the values to be written to use the same paradigm for them on all
supported socs.
Fixes: 3536c97a52 ("clk: rockchip: add rk3368 clock controller")
Reported-by: Zhang Qing <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: zhangqing <zhangqing@rock-chips.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 535ebd428a upstream.
Both clusters have their mux bit in bit 7 of their respective register.
For whatever reason the big cluster currently lists bit 15 which is
definitly wrong.
Fixes: 3536c97a52 ("clk: rockchip: add rk3368 clock controller")
Reported-by: Zhang Qing <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: zhangqing <zhangqing@rock-chips.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 93c77d2999 upstream.
Using an at91sam9g20ek development board with DTS configuration may trigger
a kernel panic because of a NULL pointer dereference exception, while
configuring DMA. Let's fix this by adding a check for pdata before
dereferencing it.
Signed-off-by: Brent Taylor <motobud@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9951362479 upstream.
Normally the timeout clock frequency is read from the capabilities
register. It is also possible to set the value prior to calling
sdhci_add_host() in which case that value will override the
capabilities register value. However that was being done after
calculating max_busy_timeout so that max_busy_timeout was being
calculated using the wrong value of timeout_clk.
Fix that by moving the override before max_busy_timeout is
calculated.
The result is that the max_busy_timeout and max_discard
increase for BSW devices so that, for example, the time for
mkfs.ext4 on a 64GB eMMC drops from about 1 minute 40 seconds
to about 20 seconds.
Note, in the future, the capabilities setting will be tidied up
and this override won't be used anymore. However this fix is
needed for stable.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3491b69045 upstream.
The new code to do the clock rate setting externally to the SDMMC
module has a shortcut to not propagate changes with a 0 rate to
the CAR by simply bailing out. This breaks proper cutting of the
card clock. Fix it by directly calling the correct sdhci function.
Fixes: a8e326a911 "mmc: tegra: implement module external clock change"
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7bf037d6ac upstream.
SD card support for Tegra114 started failing after commit a8e326a911
("mmc: tegra: implement module external clock change") was merged. This
commit was part of a series to enable UHS-I modes for Tegra. To
workaround this problem for now, disable UHS-I modes for Tegra114 by
separating the soc data structures for Tegra114 and Tegra124 so that
UHS-I is still enabled for Tegra124 but not Tegra114.
Fixes: a8e326a911 ("mmc: tegra: implement module external clock change")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0ca33b4ad9 upstream.
Commit 1140011ee9 ("mmc: sdhci-pxav3: Modify clock settings for the
SDR50 and DDR50 modes") broke any chance of the SDR50 or DDR50 modes
being used.
The commit claims that SDR50 and DDR50 require clock adjustments in
the SDIO3 Configuration register, which is located via the "conf-sdio3"
resource. However, when this resource is given, we fail to read the
host capabilities 1 register, resulting in host->caps1 being zero.
Hence, both SDHCI_SUPPORT_SDR50 and SDHCI_SUPPORT_DDR50 bits remain
zero, disabling the SDR50 and DDR50 modes.
The underlying idea in this function appears to be to read the device
capabilities, modify them, and set SDHCI_QUIRK_MISSING_CAPS to cause
our modified capabilities to be used. Implement exactly that.
Fixes: 1140011ee9 ("mmc: sdhci-pxav3: Modify clock settings for the SDR50 and DDR50 modes")
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7f05538af7 upstream.
The calculation for the timeout based on the number of card clocks is
incorrect. The calculation assumed:
timeout in microseconds = clock cycles / clock in Hz
which is clearly a several orders of magnitude wrong. Fix this by
multiplying the clock cycles by 1000000 prior to dividing by the Hz
based clock. Also, as per part 1, ensure that the division rounds
up.
As this needs 64-bit math via do_div(), avoid it if the clock cycles
is zero.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fafcfda9e7 upstream.
The data timeout gives the minimum amount of time that should be
waited before timing out if no data is received from the card.
Simply dividing the nanosecond part by 1000 does not give this
required guarantee, since such a division rounds down. Use
DIV_ROUND_UP() to give the desired timeout.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 054cedff5e upstream.
If we terminate a command early, we fail to properly clean up the DMA
mappings for the data part of the request. Put this clean up to the
tasklet, which is the common path for finishing a request so we always
clean up after ourselves.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[ Split original patch so that it now contains only the fix ]
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit edd63fcc97 upstream.
Unnecessarily mapping and unmapping the align buffer for SD cards is
expensive: performance measurements on iMX6 show that this gives a hit
of 10% on hdparm buffered disk reads.
MMC/SD card IO comes from the mm/vfs which gives us page based IO, so
for this case, the align buffer is not going to be used. However, we
still map and unmap this buffer.
Eliminate this by switching the align buffer to be a DMA coherent
buffer, which needs no DMA maintenance to access the buffer.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 771a3dc225 upstream.
sdhci_post_req() exists to unmap a previously mapped but already
finished request, while the next request is in progress. However, the
state of the SDHCI_REQ_USE_DMA flag depends on the last submitted
request.
This means we can end up clearing the flag due to a quirk, which then
means that sdhci_post_req() fails to unmap the DMA buffer, potentially
leading to data corruption.
We can safely ignore the SDHCI_REQ_USE_DMA here, as testing
data->host_cookie is entirely sufficient.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[ Re-based to apply as a separate fix ]
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 71fcbda0fc upstream.
When we get a response CRC error on a command, it means that the
response we received back from the card was not correct. It does not
mean that the card did not receive the command correctly. If the
command is one which initiates a data transfer, the card can enter the
data transfer state, and start sending data.
Moreover, if the request contained a data phase, we do not clean this
up, and this results in the driver triggering DMA API debug warnings,
and also creates a race condition in the driver, between running the
finish_tasklet and the data transfer interrupts, which can trigger a
"Got data interrupt" state dump.
Fix this by handing a response CRC error slightly differently: record
the failure of the data initiating command, but allow the remainder of
the request to be processed normally. This is safe as core MMC checks
the status of all commands and data transfer phases of the request.
If the card does not initiate a data transfer, then we should time out
according to the data transfer parameters.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[ Fix missing parenthesis around bitwise-AND expression, and tweak subject ]
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 83c742c344 upstream.
If mmc_blk_ioctl returns -EINVAL, blkdev_ioctl continues to
work without returning err to user-space. But now we check
CAP_SYS_RAWIO firstly, so we return -EPERM to blkdev_ioctl,
which make blkdev_ioctl return -EPERM to user-space directly.
So this will break all the ioctl with BLKROSET. Now we find
Android-adb suffer it for the following log:
remount of /system failed;
couldn't make block device writable: Operation not permitted
openat(AT_FDCWD, "/dev/block/platform/ff420000.dwmmc/by-name/system", O_RDONLY) = 3
ioctl(3, BLKROSET, 0) = -1 EPERM (Operation not permitted)
Fixes: a5f5774c55 ("mmc: block: Add new ioctl to send multi commands")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4db9675d92 upstream.
Some Lenovo ideapad models lack a physical rfkill switch.
On Lenovo models ideapad Y700 Touch-15ISK and ideapad Y700-15ISK,
ideapad-laptop would wrongly report all radios as blocked by
hardware which caused wireless network connections to fail.
Add these models without an rfkill switch to the no_hw_rfkill list.
Signed-off-by: John Dahlstrom <jodarom@sdf.org>
Cc: <stable@vger.kernel.org> # 3.17.x-: 4fa9dab: ideapad_laptop: Lenovo G50-30 fix rfkill reports wireless blocked
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 968ce1b1f4 upstream.
The old web page for the hwmon subsystem is no longer operational,
and the mailing list has become unreliable. Move both to kernel.org.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c8b08ca558 upstream.
mkspec is copying built kernel to temporrary location
/boot/vmlinuz-$KERNELRELEASE-rpm
and runs installkernel on it. This however directly leads to grub2
menuentry for this suffixed binary being generated as well during the run
of installkernel script.
Later in the process the temporary -rpm suffixed files are removed, and
therefore we end up with spurious (and non-functional) grub2 menu entries
for each installed kernel RPM.
Fix that by using a different temporary name (prefixed by '.'), so that
the binary is not recognized as an actual kernel binary and no menuentry
is created for it.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fixes: 3c9c7a14b6 ("rpm-pkg: add %post section to create initramfs and grub hooks")
Signed-off-by: Michal Marek <mmarek@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 42f9d3c688 upstream.
Documentation/Changes still lists this as the minimal required version,
so it ought to remain usable for the time being.
Fixes: d2036f30cf ("scripts/kconfig/Makefile: Allow KBUILD_DEFCONFIG to be a target")
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Michal Marek <mmarek@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f75d48644c upstream.
__clear_bit_unlock() is a special little snowflake. While it carries the
non-atomic '__' prefix, it is specifically documented to pair with
test_and_set_bit() and therefore should be 'somewhat' atomic.
Therefore the generic implementation of __clear_bit_unlock() cannot use
the fully non-atomic __clear_bit() as a default.
If an arch is able to do better; is must provide an implementation of
__clear_bit_unlock() itself.
Specifically, this came up as a result of hackbench livelock'ing in
slab_lock() on ARC with SMP + SLUB + !LLSC.
The issue was incorrect pairing of atomic ops.
slab_lock() -> bit_spin_lock() -> test_and_set_bit()
slab_unlock() -> __bit_spin_unlock() -> __clear_bit()
The non serializing __clear_bit() was getting "lost"
80543b8e: ld_s r2,[r13,0] <--- (A) Finds PG_locked is set
80543b90: or r3,r2,1 <--- (B) other core unlocks right here
80543b94: st_s r3,[r13,0] <--- (C) sets PG_locked (overwrites unlock)
Fixes ARC STAR 9000817404 (and probably more).
Reported-by: Vineet Gupta <Vineet.Gupta1@synopsys.com>
Tested-by: Vineet Gupta <Vineet.Gupta1@synopsys.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Helge Deller <deller@gmx.de>
Cc: James E.J. Bottomley <jejb@parisc-linux.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Noam Camus <noamc@ezchip.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20160309114054.GJ6356@twins.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3debb0a9dd upstream.
The trace_printk() code will allocate extra buffers if the compile detects
that a trace_printk() is used. To do this, the format of the trace_printk()
is saved to the __trace_printk_fmt section, and if that section is bigger
than zero, the buffers are allocated (along with a message that this has
happened).
If trace_printk() uses a format that is not a constant, and thus something
not guaranteed to be around when the print happens, the compiler optimizes
the fmt out, as it is not used, and the __trace_printk_fmt section is not
filled. This means the kernel will not allocate the special buffers needed
for the trace_printk() and the trace_printk() will not write anything to the
tracing buffer.
Adding a "__used" to the variable in the __trace_printk_fmt section will
keep it around, even though it is set to NULL. This will keep the string
from being printed in the debugfs/tracing/printk_formats section as it is
not needed.
Reported-by: Vlastimil Babka <vbabka@suse.cz>
Fixes: 07d777fe8c "tracing: Add percpu buffers for trace_printk()"
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cb86e05390 upstream.
Joel Fernandes reported that the function tracing of preempt disabled
sections was not being reported when running either the preemptirqsoff or
preemptoff tracers. This was due to the fact that the function tracer
callback for those tracers checked if irqs were disabled before tracing. But
this fails when we want to trace preempt off locations as well.
Joel explained that he wanted to see funcitons where interrupts are enabled
but preemption was disabled. The expected output he wanted:
<...>-2265 1d.h1 3419us : preempt_count_sub <-irq_exit
<...>-2265 1d..1 3419us : __do_softirq <-irq_exit
<...>-2265 1d..1 3419us : msecs_to_jiffies <-__do_softirq
<...>-2265 1d..1 3420us : irqtime_account_irq <-__do_softirq
<...>-2265 1d..1 3420us : __local_bh_disable_ip <-__do_softirq
<...>-2265 1..s1 3421us : run_timer_softirq <-__do_softirq
<...>-2265 1..s1 3421us : hrtimer_run_pending <-run_timer_softirq
<...>-2265 1..s1 3421us : _raw_spin_lock_irq <-run_timer_softirq
<...>-2265 1d.s1 3422us : preempt_count_add <-_raw_spin_lock_irq
<...>-2265 1d.s2 3422us : _raw_spin_unlock_irq <-run_timer_softirq
<...>-2265 1..s2 3422us : preempt_count_sub <-_raw_spin_unlock_irq
<...>-2265 1..s1 3423us : rcu_bh_qs <-__do_softirq
<...>-2265 1d.s1 3423us : irqtime_account_irq <-__do_softirq
<...>-2265 1d.s1 3423us : __local_bh_enable <-__do_softirq
There's a comment saying that the irq disabled check is because there's a
possible race that tracing_cpu may be set when the function is executed. But
I don't remember that race. For now, I added a check for preemption being
enabled too to not record the function, as there would be no race if that
was the case. I need to re-investigate this, as I'm now thinking that the
tracing_cpu will always be correct. But no harm in keeping the check for
now, except for the slight performance hit.
Link: http://lkml.kernel.org/r/1457770386-88717-1-git-send-email-agnel.joel@gmail.com
Fixes: 5e6d2b9cfa "tracing: Use one prologue for the preempt irqs off tracer function tracers"
Reported-by: Joel Fernandes <agnel.joel@gmail.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bedf2a65c1 upstream.
Some PX laptops don't provide an ACPI method to control dGPU power. On
those systems, the driver is responsible for handling the dGPU power
state. Disable runtime PM on them until support for this is implemented.
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b36f7d26a7 upstream.
The function this used changed in
092c96a8ab
drm/radeon: fix dp link rate selection (v2)
However for MST we should just always train to the
max link/rate. Though we probably need to limit this
for future hw, in theory radeon won't support it.
This fixes my 30" monitor with MST enabled.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 459ee1c3fd upstream.
As observed on Apple iMac10,1, DCE-3.2, RV-730,
link rate of 2.7 Ghz is not selected, because
the args.v1.ucConfig flag setting for 2.7 Ghz
gets overwritten by a following assignment of
the transmitter to use.
Move link rate setup a few lines down to fix this.
In practice this didn't have any positive or
negative effect on display setup on the tested
iMac10,1 so i don't know if backporting to stable
makes sense or not.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e64c952efb upstream.
Some PX laptops don't provide an ACPI method to control dGPU power. On
those systems, the driver is responsible for handling the dGPU power
state. Disable runtime PM on them until support for this is implemented.
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 585cb132a4 upstream.
The copy_from_user() function returns the number of bytes not copied but
we want to return a negative error code.
Fixes: 463873d570 ('drm/vc4: Add an API for creating GPU shaders in GEM BOs.')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 378c6520e7 upstream.
This commit fixes the following security hole affecting systems where
all of the following conditions are fulfilled:
- The fs.suid_dumpable sysctl is set to 2.
- The kernel.core_pattern sysctl's value starts with "/". (Systems
where kernel.core_pattern starts with "|/" are not affected.)
- Unprivileged user namespace creation is permitted. (This is
true on Linux >=3.8, but some distributions disallow it by
default using a distro patch.)
Under these conditions, if a program executes under secure exec rules,
causing it to run with the SUID_DUMP_ROOT flag, then unshares its user
namespace, changes its root directory and crashes, the coredump will be
written using fsuid=0 and a path derived from kernel.core_pattern - but
this path is interpreted relative to the root directory of the process,
allowing the attacker to control where a coredump will be written with
root privileges.
To fix the security issue, always interpret core_pattern for dumps that
are written under SUID_DUMP_ROOT relative to the root directory of init.
Signed-off-by: Jann Horn <jann@thejh.net>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 744742d692 upstream.
The 'reqs' member of fuse_io_priv serves two purposes. First is to track
the number of oustanding async requests to the server and to signal that
the io request is completed. The second is to be a reference count on the
structure to know when it can be freed.
For sync io requests these purposes can be at odds. fuse_direct_IO() wants
to block until the request is done, and since the signal is sent when
'reqs' reaches 0 it cannot keep a reference to the object. Yet it needs to
use the object after the userspace server has completed processing
requests. This leads to some handshaking and special casing that it
needlessly complicated and responsible for at least one race condition.
It's much cleaner and safer to maintain a separate reference count for the
object lifecycle and to let 'reqs' just be a count of outstanding requests
to the userspace server. Then we can know for sure when it is safe to free
the object without any handshaking or special cases.
The catch here is that most of the time these objects are stack allocated
and should not be freed. Initializing these objects with a single reference
that is never released prevents accidental attempts to free the objects.
Fixes: 9d5722b777 ("fuse: handle synchronous iocbs internally")
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7cabc61e01 upstream.
There's a race in fuse_direct_IO(), whereby is_sync_kiocb() is called on an
iocb that could have been freed if async io has already completed. The fix
in this case is simple and obvious: cache the result before starting io.
It was discovered by KASan:
kernel: ==================================================================
kernel: BUG: KASan: use after free in fuse_direct_IO+0xb1a/0xcc0 at addr ffff88036c414390
Signed-off-by: Robert Doebbelin <robert@quobyte.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Fixes: bcba24ccdc ("fuse: enable asynchronous processing direct IO")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fafcde3ac1 upstream.
Inside multipath_make_request(), multipath maps the incoming
bio into low level device's bio, but it is totally wrong to
copy the bio into mapped bio via '*mapped_bio = *bio'. For
example, .__bi_remaining is kept in the copy, especially if
the incoming bio is chained to via bio splitting, so .bi_end_io
can't be called for the mapped bio at all in the completing path
in this kind of situation.
This patch fixes the issue by using clone style.
Reported-and-tested-by: Andrea Righi <righi.andrea@gmail.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 550da24f8d upstream.
break_stripe_batch_list breaks up a batch and copies some flags from
the batch head to the members, preserving others.
It doesn't preserve or copy STRIPE_PREREAD_ACTIVE. This is not
normally a problem as STRIPE_PREREAD_ACTIVE is cleared when a
stripe_head is added to a batch, and is not set on stripe_heads
already in a batch.
However there is no locking to ensure one thread doesn't set the flag
after it has just been cleared in another. This does occasionally happen.
md/raid5 maintains a count of the number of stripe_heads with
STRIPE_PREREAD_ACTIVE set: conf->preread_active_stripes. When
break_stripe_batch_list clears STRIPE_PREREAD_ACTIVE inadvertently
this could becomes incorrect and will never again return to zero.
md/raid5 delays the handling of some stripe_heads until
preread_active_stripes becomes zero. So when the above mention race
happens, those stripe_heads become blocked and never progress,
resulting is write to the array handing.
So: change break_stripe_batch_list to preserve STRIPE_PREREAD_ACTIVE
in the members of a batch.
URL: https://bugzilla.kernel.org/show_bug.cgi?id=108741
URL: https://bugzilla.redhat.com/show_bug.cgi?id=1258153
URL: http://thread.gmane.org/5649C0E9.2030204@zoner.cz
Reported-by: Martin Svec <martin.svec@zoner.cz> (and others)
Tested-by: Tom Weber <linux@junkyard.4t2.com>
Fixes: 1b956f7a8f ("md/raid5: be more selective about distributing flags across batch.")
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23ddba80eb upstream.
This is the raid10 counterpart of the bug fixed by Nate
(raid1: include bio_end_io_list in nr_queued to prevent freeze_array hang)
Fixes: 95af587e95(md/raid10: ensure device failure recorded before write request returns)
Cc: Nate Dailey <nate.dailey@stratus.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ab2a4b806 upstream.
Revert commit
e9e4c377e2f563(md/raid5: per hash value and exclusive wait_for_stripe)
The problem is raid5_get_active_stripe waits on
conf->wait_for_stripe[hash]. Assume hash is 0. My test release stripes
in this order:
- release all stripes with hash 0
- raid5_get_active_stripe still sleeps since active_stripes >
max_nr_stripes * 3 / 4
- release all stripes with hash other than 0. active_stripes becomes 0
- raid5_get_active_stripe still sleeps, since nobody wakes up
wait_for_stripe[0]
The system live locks. The problem is active_stripes isn't a per-hash
count. Revert the patch makes the live lock go away.
Cc: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Cc: NeilBrown <neilb@suse.de>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 27a353c026 upstream.
check_reshape() is called from raid5d thread. raid5d thread shouldn't
call mddev_suspend(), because mddev_suspend() waits for all IO finish
but IO is handled in raid5d thread, we could easily deadlock here.
This issue is introduced by
738a273 ("md/raid5: fix allocation of 'scribble' array.")
Reported-and-tested-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7597e69de upstream.
'max_discard_sectors' is in sectors, while 'stripe' is in bytes.
This fixes the problem where DISCARD would get disabled on some larger
RAID5 configurations (6 or more drives in my testing), while it worked
as expected with smaller configurations.
Fixes: 620125f2bf ("MD: raid5 trim support")
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ccfc7bf1f0 upstream.
If raid1d is handling a mix of read and write errors, handle_read_error's
call to freeze_array can get stuck.
This can happen because, though the bio_end_io_list is initially drained,
writes can be added to it via handle_write_finished as the retry_list
is processed. These writes contribute to nr_pending but are not included
in nr_queued.
If a later entry on the retry_list triggers a call to handle_read_error,
freeze array hangs waiting for nr_pending == nr_queued+extra. The writes
on the bio_end_io_list aren't included in nr_queued so the condition will
never be satisfied.
To prevent the hang, include bio_end_io_list writes in nr_queued.
There's probably a better way to handle decrementing nr_queued, but this
seemed like the safest way to avoid breaking surrounding code.
I'm happy to supply the script I used to repro this hang.
Fixes: 55ce74d4bfe1b(md/raid1: ensure device failure recorded before write request returns.)
Signed-off-by: Nate Dailey <nate.dailey@stratus.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ab73ef4639 upstream.
When dqget() in __dquot_initialize() fails e.g. due to IO error,
__dquot_initialize() will pass an array of uninitialized pointers to
dqput_all() and thus can lead to deference of random data. Fix the
problem by properly initializing the array.
Signed-off-by: Nikolay Borisov <kernel@kyup.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f778cc6571 upstream.
read{l,w}() write{l,w}() primitives should use le{16,32}_to_cpu() and
cpu_to_le{16,32}() respectively to ensure device registers are read
correctly in Big Endian CPU configuration.
Per Arnd Bergmann
| Most drivers using readl() or readl_relaxed() expect those to perform byte
| swaps on big-endian architectures, as the registers tend to be fixed endian
This was needed for getting UART to work correctly on a Big Endian ARC.
The ARC accessors originally were fine, and the bug got introduced
inadventently by commit b8a0330239 ("ARCv2: barriers")
Fixes: b8a0330239 ("ARCv2: barriers")
Link: http://lkml.kernel.org/r/201603100845.30602.arnd@arndb.de
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lada Trimasova <ltrimas@synopsys.com>
[vgupta: beefed up changelog, added Fixes/stable tags]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7de7ac785a upstream.
There are XCHAL_NUM_DBREAK registers, clear them all.
This also fixes cryptic assembler error message with binutils 2.25 when
XCHAL_NUM_DBREAK is 0:
as: out of memory allocating 18446744073709551575 bytes after a total
of 495616 bytes
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a67cc9aa2d upstream.
Disabling pagefault makes little sense there, preemption disabling is
what was meant.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 362014c8d9 upstream.
Simulator stdin may be connected to a file, when its end is reached
kernel hangs in infinite loop inside rs_poll, because simc_poll always
signals that descriptor 0 is readable and simc_read always returns 0.
Check simc_read return value and exit loop if it's not positive. Also
don't rewind polling timer if it's zero.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d6785d9152 upstream.
Running the following command:
busybox cat /sys/kernel/debug/tracing/trace_pipe > /dev/null
with any tracing enabled pretty very quickly leads to various NULL
pointer dereferences and VM BUG_ON()s, such as these:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000020
IP: [<ffffffff8119df6c>] generic_pipe_buf_release+0xc/0x40
Call Trace:
[<ffffffff811c48a3>] splice_direct_to_actor+0x143/0x1e0
[<ffffffff811c42e0>] ? generic_pipe_buf_nosteal+0x10/0x10
[<ffffffff811c49cf>] do_splice_direct+0x8f/0xb0
[<ffffffff81196869>] do_sendfile+0x199/0x380
[<ffffffff81197600>] SyS_sendfile64+0x90/0xa0
[<ffffffff8192cbee>] entry_SYSCALL_64_fastpath+0x12/0x6d
page dumped because: VM_BUG_ON_PAGE(atomic_read(&page->_count) == 0)
kernel BUG at include/linux/mm.h:367!
invalid opcode: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC
RIP: [<ffffffff8119df9c>] generic_pipe_buf_release+0x3c/0x40
Call Trace:
[<ffffffff811c48a3>] splice_direct_to_actor+0x143/0x1e0
[<ffffffff811c42e0>] ? generic_pipe_buf_nosteal+0x10/0x10
[<ffffffff811c49cf>] do_splice_direct+0x8f/0xb0
[<ffffffff81196869>] do_sendfile+0x199/0x380
[<ffffffff81197600>] SyS_sendfile64+0x90/0xa0
[<ffffffff8192cd1e>] tracesys_phase2+0x84/0x89
(busybox's cat uses sendfile(2), unlike the coreutils version)
This is because tracing_splice_read_pipe() can call splice_to_pipe()
with spd->nr_pages == 0. spd_pages underflows in splice_to_pipe() and
we fill the page pointers and the other fields of the pipe_buffers with
garbage.
All other callers of splice_to_pipe() avoid calling it when nr_pages ==
0, and we could make tracing_splice_read_pipe() do that too, but it
seems reasonable to have splice_to_page() handle this condition
gracefully.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e53b50c0cb upstream.
early_init_dt_alloc_reserved_memory_arch passes end as 0 to
__memblock_alloc_base, when limits are not specified. But
__memblock_alloc_base takes end value of 0 as MEMBLOCK_ALLOC_ACCESSIBLE
and limits the end to memblock.current_limit. This results in regions
never being placed in HIGHMEM area, for e.g. CMA.
Let __memblock_alloc_base allocate from anywhere in memory if limits are
not specified.
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Vinayak Menon <vinmenon@codeaurora.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 19c8f421a6 upstream.
New generation devices have firmware which has more than 256 flowrings.
E.g. following debugging message comes from 14e4:4365 BCM4366:
[ 194.606245] brcmfmac: brcmf_pcie_init_ringbuffers Nr of flowrings is 264
At various code places (related to flowrings) we were using u8 which
could lead to storing wrong number or infinite loops when indexing with
this type. This issue was quite easy to spot in brcmf_flowring_detach
where it led to infinite loop e.g. on failed initialization.
This patch switches code to proper types and increases the maximum
number of supported flowrings to 512.
Originally this change was sent in September 2015, but back it was
causing a regression on BCM43602 resulting in:
Unable to handle kernel NULL pointer dereference at virtual address ...
The reason for this regression was missing update (s/u8/u16) of struct
brcmf_flowring_ring. This problem was handled in 9f64df9 ("brcmfmac: Fix
bug in flowring management."). Starting with that it's safe to apply
this original patch as it doesn't cause a regression anymore.
This patch fixes an infinite loop on BCM4366 which is supported since
4.4 so it makes sense to apply it to stable 4.4+.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 928b6519af upstream.
Function eth_prepare_mac_addr_change() is called as part of MAC
address change. This function check if interface is running.
To enable change MAC address when interface is running:
IFF_LIVE_ADDR_CHANGE flag must be set to dev->priv_flags field
Fixes: c5aff18204 ("net: mvneta: driver for Marvell Armada 370/XP
network unit")
Signed-off-by: Dmitri Epshtein <dima@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b021cbf3c upstream.
Before 2e91fa7f6d ("cgroup: keep zombies associated with their
original cgroups"), all dead tasks were associated with init_css_set.
If a zombie task is requested for migration, while migration prep
operations would still be performed on init_css_set, the actual
migration would ignore zombie tasks. As init_css_set is always valid,
this worked fine.
However, after 2e91fa7f6d, zombie tasks stay with the css_set it was
associated with at the time of death. Let's say a task T associated
with cgroup A on hierarchy H-1 and cgroup B on hiearchy H-2. After T
becomes a zombie, it would still remain associated with A and B. If A
only contains zombie tasks, it can be removed. On removal, A gets
marked offline but stays pinned until all zombies are drained. At
this point, if migration is initiated on T to a cgroup C on hierarchy
H-2, migration path would try to prepare T's css_set for migration and
trigger the following.
WARNING: CPU: 0 PID: 1576 at kernel/cgroup.c:474 cgroup_get+0x121/0x160()
CPU: 0 PID: 1576 Comm: bash Not tainted 4.4.0-work+ #289
...
Call Trace:
[<ffffffff8127e63c>] dump_stack+0x4e/0x82
[<ffffffff810445e8>] warn_slowpath_common+0x78/0xb0
[<ffffffff810446d5>] warn_slowpath_null+0x15/0x20
[<ffffffff810c33e1>] cgroup_get+0x121/0x160
[<ffffffff810c349b>] link_css_set+0x7b/0x90
[<ffffffff810c4fbc>] find_css_set+0x3bc/0x5e0
[<ffffffff810c5269>] cgroup_migrate_prepare_dst+0x89/0x1f0
[<ffffffff810c7547>] cgroup_attach_task+0x157/0x230
[<ffffffff810c7a17>] __cgroup_procs_write+0x2b7/0x470
[<ffffffff810c7bdc>] cgroup_tasks_write+0xc/0x10
[<ffffffff810c4790>] cgroup_file_write+0x30/0x1b0
[<ffffffff811c68fc>] kernfs_fop_write+0x13c/0x180
[<ffffffff81151673>] __vfs_write+0x23/0xe0
[<ffffffff81152494>] vfs_write+0xa4/0x1a0
[<ffffffff811532d4>] SyS_write+0x44/0xa0
[<ffffffff814af2d7>] entry_SYSCALL_64_fastpath+0x12/0x6f
It doesn't make sense to prepare migration for css_sets pointing to
dead cgroups as they are guaranteed to contain only zombies which are
ignored later during migration. This patch makes cgroup destruction
path mark all affected css_sets as dead and updates the migration path
to ignore them during preparation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: 2e91fa7f6d ("cgroup: keep zombies associated with their original cgroups")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6a0e78072c upstream.
The Add Advertising command handler does the appropriate checks for
the AD and Scan Response data, however fails to take into account the
general length of the mgmt command itself, which could lead to
potential buffer overflows. This patch adds the necessary check that
the mgmt command length is consistent with the given ad and scan_rsp
lengths.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 10e7ac22cd upstream.
Calling return copy_to_user(...) in an ioctl will not do the right thing
if there's a pagefault: copy_to_user returns the number of bytes not
copied in this case.
Fix up watchdog/rc32434_wdt to do
return copy_to_user(...)) ? -EFAULT : 0;
instead.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a1ee1932aa upstream.
While working on a script to restore all sysctl params before a series of
tests I found that writing any value into the
/proc/sys/kernel/{nmi_watchdog,soft_watchdog,watchdog,watchdog_thresh}
causes them to call proc_watchdog_update().
NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
There doesn't appear to be a reason for doing this work every time a write
occurs, so only do it when the values change.
Signed-off-by: Josh Hunt <johunt@akamai.com>
Acked-by: Don Zickus <dzickus@redhat.com>
Reviewed-by: Aaron Tomlin <atomlin@redhat.com>
Cc: Ulrich Obergfell <uobergfe@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c11e554fb upstream.
Commit 1f330c3279 ("drivers/firmware/broadcom/bcm47xx_nvram.c: use
__ioread32_copy() instead of open-coding") switched to use a generic
copy function, but failed to notice that the header pointer is updated
between the two copies, resulting in bogus data being copied in the
latter one. Fix by keeping the old header pointer.
The patch fixes totally broken networking on WRT54GL router (both LAN and
WLAN interfaces fail to probe).
Fixes: 1f330c3279 ("drivers/firmware/broadcom/bcm47xx_nvram.c: use __ioread32_copy() instead of open-coding")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Rafal Milecki <zajec5@gmail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b0f84ac352 upstream.
All architectures now need ioremap_uc(), ia64 seems defines this already
through its ioremap_nocache() and it already ensures it *only* uses UC.
This is needed since v4.3 to complete an allyesconfig compile on ia64,
there were others archs that needed this, and this one seems to have
fallen through the cracks.
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b6e6edcfa4 upstream.
Setting the original memory.limit_in_bytes hardlimit is subject to a
race condition when the desired value is below the current usage. The
code tries a few times to first reclaim and then see if the usage has
dropped to where we would like it to be, but there is no locking, and
the workload is free to continue making new charges up to the old limit.
Thus, attempting to shrink a workload relies on pure luck and hope that
the workload happens to cooperate.
To fix this in the cgroup2 memory.max knob, do it the other way round:
set the limit first, then try enforcement. And if reclaim is not able
to succeed, trigger OOM kills in the group. Keep going until the new
limit is met, we run out of OOM victims and there's only unreclaimable
memory left, or the task writing to memory.max is killed. This allows
users to shrink groups reliably, and the behavior is consistent with
what happens when new charges are attempted in excess of memory.max.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Vladimir Davydov <vdavydov@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 588083bb37 upstream.
When setting memory.high below usage, nothing happens until the next
charge comes along, and then it will only reclaim its own charge and not
the now potentially huge excess of the new memory.high. This can cause
groups to stay in excess of their memory.high indefinitely.
To fix that, when shrinking memory.high, kick off a reclaim cycle that
goes after the delta.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Vladimir Davydov <vdavydov@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f8b11260a4 upstream.
When bch_cache_set_alloc() fails to kzalloc the cache_set, the
asyncronous closure handling tries to dereference a cache_set that
hadn't yet been allocated inside of cache_set_flush() which is called
by __cache_set_unregister() during cleanup. This appears to happen only
during an OOM condition on bcache_register.
Signed-off-by: Eric Wheeler <bcache@linux.ewheeler.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07cc6ef8ed upstream.
The bch_writeback_thread might BUG_ON in read_dirty() if
dc->sb==BDEV_STATE_DIRTY and bch_sectors_dirty_init has not yet completed
its related initialization. This patch downs the dc->writeback_lock until
after initialization is complete, thus preventing bch_writeback_thread
from proceeding prematurely.
See this thread:
http://thread.gmane.org/gmane.linux.kernel.bcache.devel/3453
Signed-off-by: Eric Wheeler <bcache@linux.ewheeler.net>
Tested-by: Marc MERLIN <marc@merlins.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 51093254bf upstream.
Let the target core check task existence instead of the SRP target
driver. Additionally, let the target core check the validity of the
task management request instead of the ib_srpt driver.
This patch fixes the following kernel crash:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000001
IP: [<ffffffffa0565f37>] srpt_handle_new_iu+0x6d7/0x790 [ib_srpt]
Oops: 0002 [#1] SMP
Call Trace:
[<ffffffffa05660ce>] srpt_process_completion+0xde/0x570 [ib_srpt]
[<ffffffffa056669f>] srpt_compl_thread+0x13f/0x160 [ib_srpt]
[<ffffffff8109726f>] kthread+0xcf/0xe0
[<ffffffff81613cfc>] ret_from_fork+0x7c/0xb0
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Fixes: 3e4f574857 ("ib_srpt: Convert TMR path to target_submit_tmr")
Tested-by: Alex Estrin <alex.estrin@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e4298be45 upstream.
Avoid that discard requests with size => PAGE_SIZE fail with
-EIO. Refuse discard requests if the discard size is not a
multiple of the page size.
Fixes: 2dbe549576 ("brd: Refuse improperly aligned discard requests")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Jan Kara <jack@suse.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Robert Elliot <elliott@hp.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fdc69e7df3 upstream.
The set_pte_at() function must update the hardware PTE_RDONLY bit
depending on the state of the PTE_WRITE and PTE_DIRTY bits of the given
entry value. However, it currently only performs this for pte_valid()
entries, ignoring PTE_PROT_NONE. The side-effect is that PROT_NONE
mappings would not have the PTE_RDONLY bit set. Without
CONFIG_ARM64_HW_AFDBM, this is not an issue since such PROT_NONE pages
are not accessible anyway.
With commit 2f4b829c62 ("arm64: Add support for hardware updates of
the access and dirty pte bits"), the ptep_set_wrprotect() function was
re-written to cope with automatic hardware updates of the dirty state.
As an optimisation, only PTE_RDONLY is checked to assess the "dirty"
status. Since set_pte_at() does not set this bit for PROT_NONE mappings,
such pages may be considered "dirty" as a result of
ptep_set_wrprotect().
This patch updates the pte_valid() check to pte_present() in
set_pte_at(). It also adds PTE_PROT_NONE to the swap entry bits comment.
Fixes: 2f4b829c62 ("arm64: Add support for hardware updates of the access and dirty pte bits")
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Ganapatrao Kulkarni <gkulkarni@caviumnetworks.com>
Tested-by: Ganapatrao Kulkarni <gkulkarni@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e0a8604f13 upstream.
pca953x_gpio_set_multiple() divides by 4 to convert from longs to bytes,
which assumes a 32-bit platform, and is not correct on 64-bit platforms.
Use "sizeof(...)" instead to fix this.
Fixes: b4818afeac ("gpio: pca953x: Add set_multiple to allow multiple bits to be set in one write.")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c0a2ad9b50 upstream.
On umount path, jbd2_journal_destroy() writes latest transaction ID
(->j_tail_sequence) to be used at next mount.
The bug is that ->j_tail_sequence is not holding latest transaction ID
in some cases. So, at next mount, there is chance to conflict with
remaining (not overwritten yet) transactions.
mount (id=10)
write transaction (id=11)
write transaction (id=12)
umount (id=10) <= the bug doesn't write latest ID
mount (id=10)
write transaction (id=11)
crash
mount
[recovery process]
transaction (id=11)
transaction (id=12) <= valid transaction ID, but old commit
must not replay
Like above, this bug become the cause of recovery failure, or FS
corruption.
So why ->j_tail_sequence doesn't point latest ID?
Because if checkpoint transactions was reclaimed by memory pressure
(i.e. bdev_try_to_free_page()), then ->j_tail_sequence is not updated.
(And another case is, __jbd2_journal_clean_checkpoint_list() is called
with empty transaction.)
So in above cases, ->j_tail_sequence is not pointing latest
transaction ID at umount path. Plus, REQ_FLUSH for checkpoint is not
done too.
So, to fix this problem with minimum changes, this patch updates
->j_tail_sequence, and issue REQ_FLUSH. (With more complex changes,
some optimizations would be possible to avoid unnecessary REQ_FLUSH
for example though.)
BTW,
journal->j_tail_sequence =
++journal->j_transaction_sequence;
Increment of ->j_transaction_sequence seems to be unnecessary, but
ext3 does this.
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 50fe6dd100 upstream.
Use the local uapi headers to keep in sync with "recently" added #define's
(e.g. VSS_OP_REGISTER1).
Fixes: 3eb2094c59 ("Adding makefile for tools/hv")
Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c64c1437af upstream.
i915 get_eld ops may return an error when no encoder is connected, and
currently we regard the error as fatal and skip the whole ELD
handling. This ended up with the missing ELD update at unplugging.
This patch fixes the issue by treating the error as the unplugged
state, instead of skipping the rest.
Reported-by: Libin Yang <libin.yang@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7169701ad3 upstream.
The recent addition of on-demand i915 audio component binding in the
codec driver seems leading to the unbalanced i915 power refcount,
according to Intel CI tests. Typically, it gets a kernel WARNING
like:
WARNING: CPU: 3 PID: 173 at sound/hda/hdac_i915.c:91 snd_hdac_display_power+0xf1/0x110 [snd_hda_core]()
Call Trace:
[<ffffffff813fef15>] dump_stack+0x67/0x92
[<ffffffff81078a21>] warn_slowpath_common+0x81/0xc0
[<ffffffff81078b15>] warn_slowpath_null+0x15/0x20
[<ffffffffa00f77e1>] snd_hdac_display_power+0xf1/0x110 [snd_hda_core]
[<ffffffffa015039d>] azx_intel_link_power+0xd/0x10 [snd_hda_intel]
[<ffffffffa011e32a>] azx_link_power+0x1a/0x30 [snd_hda_codec]
[<ffffffffa00f21f9>] snd_hdac_link_power+0x29/0x40 [snd_hda_core]
[<ffffffffa01192a6>] hda_codec_runtime_suspend+0x76/0xa0 [snd_hda_codec]
.....
The scenario is like below:
- HD-audio driver and i915 driver are probed concurrently at the
(almost) same time; HDA bus tries to bind with i915, but it fails
because i915 initialization is still being processed.
- Later on, HD-audio probes the HDMI codec, where it again tries to
bind with i915. At this time, it succeeds.
- At finishing the probe of HDA, it decreases the refcount as if it
were already bound at the bus probe, since the component is bound
now. This triggers a kernel WARNING due to the unbalance.
As a workaround, in this patch, we just disable the on-demand i915
component binding in the codec driver. This essentially reverts back
to the state of 4.4 kernel.
We know that this is no real solution, but it's a minimalistic simple
change that can be applied to 4.5.x kernel as stable.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94566
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd48128539 upstream.
We forgot to copy monitor_present value when updating the ELD
information. This won't change the ELD retrieval and the jack
notification behavior, but appears only in the proc output. In that
sense, it's no fatal error, but a bug is a bug is a bug.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 691be973c0 upstream.
The commit [b62232d429: ALSA: hda - Limit i915 HDMI binding only for
HSW and later] tried to limit the usage of i915 audio notifier to the
recent Intel models and switch to the old method on pre-Haswell
models. However, it assumed that the i915 component binding hasn't
been done on such models, and the assumption was wrong: namely,
Baytrail had already the i915 component binding due to powerwell
control. Thus, the workaround wasn't applied to Baytrail.
For fixing this properly, this patch introduces a new flag indicating
the usage of audio notifier and codec_has_acomp() refers to this flag
instead of checking the existence of audio component.
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 93a9ff1517 upstream.
snd_hdac_sync_audio_rate() call is mandatory only for HSW and later
models, but we call the function unconditionally blindly assuming that
the function doesn't do anything harmful. But since recently, the
function checks the validity of the passed pin NID, and eventually
spews the warning if an unexpected pin is passed. This is seen on old
chips like Baytrail.
The fix is to limit the call of this function again only for the chips
with the proper binding. This can be identified by the same flag as
the eld notifier.
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b62232d429 upstream.
It turned out that the pre-HSW Intel chips are incompatible with the
naive assumption we had -- the fixed mapping between the port and the
HD-audio widget. This may result in the bad access, as captured by
the recent patch to add a WARN_ON() for the port mapping check.
As a quick workaround, disable the i915 audio component binding for
all pre-Haswell models.
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f7c665896 upstream.
Cirrus HD-audio driver may adjust GPIO pins for EAPD dynamically
depending on the jack plug state. This works fine for the auto-mute
mode where the speaker gets muted upon the HP jack plug. OTOH, when
the auto-mute mode is off, this turns off the EAPD unexpectedly
depending on the jack state, which results in the silent speaker
output.
This patch fixes the silent speaker output issue by setting GPIO bits
constantly when the auto-mute mode is off.
Reported-and-tested-by: moosotc@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2d369c748c upstream.
Vendor ID 0x10de0082 is used by a yet-to-be-named GPU chip.
This chip also has the 2-ch audio swapping bug, so patch_nvhdmi is
appropriate here.
Signed-off-by: Aaron Plattner <aplattner@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f8e4f3537 upstream.
The current Intel HDMI codec driver supports only three fixed ports
from port B to port D. However, i915 driver may assign a DP on other
ports, e.g. port A, when no eDP is used. This incompatibility is
caught later at pin_nid_to_pin_index() and results in a warning
message like "HDMI: pin nid 4 not registered" at each time.
This patch filters out such invalid events beforehand, so that the
kernel won't be too grumbling.
Reported-by: Stefan Assmann <sassmann@kpanic.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0ab1ace856 upstream.
The commit [d507941beb: ALSA: pcm: Correct PCM BUG error message]
made the warning prefix back to "BUG:" due to its previous wrong
prefix. But a kernel message containing "BUG:" seems taken as an Oops
message wrongly by some brain-dead daemons, and it annoys users in the
end. Instead of teaching daemons, change the string again to a more
reasonable one.
Fixes: 507941beb1e ('ALSA: pcm: Correct PCM BUG error message')
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc4f000bf8 upstream.
HD-audio driver has a mechanism to trigger the runtime resume
automatically at accessing the verbs. This auto-resume, however,
causes the mutex deadlock when invoked from the regmap handler since
the regmap keeps the mutex while auto-resuming. For avoiding that,
there is some tricky check in the HDA regmap handler to return -EAGAIN
error to back-off when the codec is powered down. Then the caller of
regmap r/w will retry after properly turning on the codec power.
This works in most cases, but there seems a slight race between the
codec power check and the actual on-demand auto-resume trigger. This
resulted in the lockdep splat, eventually leading to a real deadlock.
This patch tries to address the race window by getting the runtime PM
refcount at the check time using pm_runtime_get_if_in_use(). With
this call, we can keep the power on only when the codec has been
already turned on, and back off if not.
For keeping the code consistency, the code touching the runtime PM is
stored in hdac_device.c although it's used only locally in
hdac_regmap.c.
Reported-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aae4a03386 upstream.
Allow device initialization to finish gracefully when it is in
FTL rebuild failure state. Also, recover device out of this state
after successfully secure erasing it.
Signed-off-by: Selvan Mani <smani@micron.com>
Signed-off-by: Vignesh Gunasekaran <vgunasekaran@micron.com>
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 59cf70e236 upstream.
When FTL rebuild is in progress, alloc_disk() initializes the disk
but device node will be created by add_disk() only after successful
completion of FTL rebuild. So, skip deletion of device node in
removal path when FTL rebuild is in progress.
Signed-off-by: Selvan Mani <smani@micron.com>
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e35b94738a upstream.
Remove setting and clearing MTIP_PF_EH_ACTIVE_BIT flag in
mtip_handle_tfe() as they are redundant. Also avoid waking
up service thread from mtip_handle_tfe() because it is
already woken up in case of taskfile error.
Signed-off-by: Selvan Mani <smani@micron.com>
Signed-off-by: Rajesh Kumar Sambandam <rsambandam@micron.com>
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cfc05bd313 upstream.
Service thread does not detect the need for taskfile error hanlding. Fixed the
flag condition to process taskfile error.
Signed-off-by: Selvan Mani <smani@micron.com>
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 74dc385cb4 upstream.
During the recent vb2_buffer restructuring, the calculation of the
buffer payload reported to userspace was accidentally broken for the
first encoded frame, counting only the length of the headers.
This patch re-adds the length of the actual frame data.
Fixes: 2d7007153f ("[media] media: videobuf2: Restructure vb2_buffer")
Reported-by: Michael Olbrich <m.olbrich@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c915c6876 upstream.
On my bttv card "Hauppauge WinTV [card=10]" capturing in YV12 fmt at max
size results in a solid green rectangle being captured (all colors 0 in
YUV).
This turns out to be caused by max-width (924) not being a multiple of 16.
We've likely never hit this problem before since normally xawtv / tvtime,
etc. will prefer packed pixel formats. But when using a video card which
is using xf86-video-modesetting + glamor, only planar XVideo fmts are
available, and xawtv will chose a matching capture format to avoid needing
to do conversion, triggering the solid green window problem.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b339a72e04 upstream.
The V4L2_CID_TX_EDID_PRESENT control reports if an EDID is present.
The adv7511 however still reported the EDID present after disconnecting
the HDMI cable. Fix the logic regarding this control. And when the EDID
is disconnected also call ADV7511_EDID_DETECT to notify the bridge driver.
This was also missing.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0b41ce9910 upstream.
Some UART HW has a single register combining UART_DLL/UART_DLM
(this was probably forgotten in the change that introduced the
callbacks, commit b32b19b8ff)
Fixes: b32b19b8ff ("[SERIAL] 8250: set divisor register correctly ...")
Signed-off-by: Sebastian Frias <sf84@laposte.net>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 401879c57f upstream.
The N_IRDA line discipline may access the previous line discipline's closed
and already-fre private data on open [1].
The tty->disc_data field _never_ refers to valid data on entry to the
line discipline's open() method. Rather, the ldisc is expected to
initialize that field for its own use for the lifetime of the instance
(ie. from open() to close() only).
[1]
==================================================================
BUG: KASAN: use-after-free in irtty_open+0x422/0x550 at addr ffff8800331dd068
Read of size 4 by task a.out/13960
=============================================================================
BUG kmalloc-512 (Tainted: G B ): kasan: bad access detected
-----------------------------------------------------------------------------
...
Call Trace:
[<ffffffff815fa2ae>] __asan_report_load4_noabort+0x3e/0x40 mm/kasan/report.c:279
[<ffffffff836938a2>] irtty_open+0x422/0x550 drivers/net/irda/irtty-sir.c:436
[<ffffffff829f1b80>] tty_ldisc_open.isra.2+0x60/0xa0 drivers/tty/tty_ldisc.c:447
[<ffffffff829f21c0>] tty_set_ldisc+0x1a0/0x940 drivers/tty/tty_ldisc.c:567
[< inline >] tiocsetd drivers/tty/tty_io.c:2650
[<ffffffff829da49e>] tty_ioctl+0xace/0x1fd0 drivers/tty/tty_io.c:2883
[< inline >] vfs_ioctl fs/ioctl.c:43
[<ffffffff816708ac>] do_vfs_ioctl+0x57c/0xe60 fs/ioctl.c:607
[< inline >] SYSC_ioctl fs/ioctl.c:622
[<ffffffff81671204>] SyS_ioctl+0x74/0x80 fs/ioctl.c:613
[<ffffffff852a7876>] entry_SYSCALL_64_fastpath+0x16/0x7a
Reported-and-tested-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f33798deec upstream.
commit 9ce119f318 ("tty: Fix GPF in flush_to_ldisc()") fixed a
GPF caused by a line discipline which does not define a receive_buf()
method.
However, the vt driver (and speakup driver also) pushes selection
data directly to the line discipline receive_buf() method via
tty_ldisc_receive_buf(). Fix the same problem in tty_ldisc_receive_buf().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd3a3cd6c2 upstream.
Memory mapped io (dev->mmio) should not also be writing to the ioport
(dev->iobase) registers. Add the missing 'else' to these functions.
Fixes: 0953ee4acc ("staging: comedi: ni_mio_common: checkpatch.pl cleanup (else not useful)")
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ccbc2a9e78 upstream.
On error platform_device_register_simple() returns ERR_PTR() value,
check for NULL always fails. The change corrects the check itself and
propagates the returned error upwards.
Fixes: 81fb0b9013 ("staging: android: ion_test: unregister the platform device")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1fd24a4702 upstream.
This fixes a bug in function ni_tio_input_inttrig(). The trigger number
should be compared to cmd->start_arg, not cmd->start_src.
Fixes: 6a760394d7 ("staging: comedi: ni_tiocmd: clarify the cmd->start_arg validation and use")
Signed-off-by: Spencer E. Olson <olsonse@umich.edu>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4392bf3333 upstream.
hid_ignore_special_drivers works fine until hid_scan_report autodetects and
reassign devices (for hid-multitouch, hid-microsoft and hid-rmi).
Simplify the handling of the parameter: if it is there, use hid-generic, no
matter what, and if not, scan the device or rely on the hid_have_special_driver
table.
This was detected while trying to disable hid-multitouch on a Surface Pro cover
which prevented to use the keyboard.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45c5c68282 upstream.
The Synaptics 0x11e5 over I2C found in the Asus T100-CHI requires to
fetch the signature blob to actually start sending events.
With this patch, we should be close enough to the Windows driver which
checks the content of the blob at plugin to validate or not the
touchscreen.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=113481
Fixes: 6d4f5440 ("HID: multitouch: Fetch feature reports on demand for Win8 devices")
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3b654288b1 upstream.
Even though hid_hw_* checks that passed in data_len is less than
HID_MAX_BUFFER_SIZE it is not enough, as i2c-hid does not necessarily
allocate buffers of HID_MAX_BUFFER_SIZE but rather checks all device
reports and select largest size. In-kernel users normally just send as much
data as report needs, so there is no problem, but hidraw users can do
whatever they please:
BUG: KASAN: slab-out-of-bounds in memcpy+0x34/0x54 at addr ffffffc07135ea80
Write of size 4101 by task syz-executor/8747
CPU: 2 PID: 8747 Comm: syz-executor Tainted: G BU 3.18.0 #37
Hardware name: Google Tegra210 Smaug Rev 1,3+ (DT)
Call trace:
[<ffffffc00020ebcc>] dump_backtrace+0x0/0x258 arch/arm64/kernel/traps.c:83
[<ffffffc00020ee40>] show_stack+0x1c/0x2c arch/arm64/kernel/traps.c:172
[< inline >] __dump_stack lib/dump_stack.c:15
[<ffffffc001958114>] dump_stack+0x90/0x140 lib/dump_stack.c:50
[< inline >] print_error_description mm/kasan/report.c:97
[< inline >] kasan_report_error mm/kasan/report.c:278
[<ffffffc0004597dc>] kasan_report+0x268/0x530 mm/kasan/report.c:305
[<ffffffc0004592e8>] __asan_storeN+0x20/0x150 mm/kasan/kasan.c:718
[<ffffffc0004594e0>] memcpy+0x30/0x54 mm/kasan/kasan.c:299
[<ffffffc001306354>] __i2c_hid_command+0x2b0/0x7b4 drivers/hid/i2c-hid/i2c-hid.c:178
[< inline >] i2c_hid_set_or_send_report drivers/hid/i2c-hid/i2c-hid.c:321
[<ffffffc0013079a0>] i2c_hid_output_raw_report.isra.2+0x3d4/0x4b8 drivers/hid/i2c-hid/i2c-hid.c:589
[<ffffffc001307ad8>] i2c_hid_output_report+0x54/0x68 drivers/hid/i2c-hid/i2c-hid.c:602
[< inline >] hid_hw_output_report include/linux/hid.h:1039
[<ffffffc0012cc7a0>] hidraw_send_report+0x400/0x414 drivers/hid/hidraw.c:154
[<ffffffc0012cc7f4>] hidraw_write+0x40/0x64 drivers/hid/hidraw.c:177
[<ffffffc0004681dc>] vfs_write+0x1d4/0x3cc fs/read_write.c:534
[< inline >] SYSC_pwrite64 fs/read_write.c:627
[<ffffffc000468984>] SyS_pwrite64+0xec/0x144 fs/read_write.c:614
Object at ffffffc07135ea80, in cache kmalloc-512
Object allocated with size 268 bytes.
Let's check data length against the buffer size before attempting to copy
data over.
Reported-by: Alexander Potapenko <glider@google.com>
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d74325a22 upstream.
The patch that added Logitech Dual Action gamepad support forgot to
update the special driver list for the device. This caused the logitech
driver not to probe unless kernel module load order was favorable.
Update the special driver list to fix it. Thanks to Simon Wood for the
idea.
Cc: Vitaly Katraew <zawullon@gmail.com>
Fixes: 56d0c8b7c8 ("HID: add support for Logitech Dual Action gamepads")
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e0ee3c9fa upstream.
If the initialization fails before tpm_chip_register(), put_device()
will be not called, which causes release callback not to be called.
This patch fixes the issue by adding put_device() to devres list of
the parent device.
Fixes: 313d21eeab ("tpm: device class for tpm")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 186d124f07 upstream.
The commit 0cc698af36 ("vTPM: support little endian guests") copied
the event, but without the event data, did an endian conversion on the
size and tried to output the event data from the copied version, which
has only have one byte of the data, resulting in garbage event data.
[jarkko.sakkinen@linux.intel.com: fixed minor coding style issues and
renamed the local variable tempPtr as temp_ptr now that there is an
excuse to do this.]
Signed-off-by: Harald Hoyer <harald@redhat.com>
Fixes: 0cc698af36 ("vTPM: support little endian guests")
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 15c13dfcad upstream.
The bus data transfer interface was missing the check if the device is
in enabled state, this may lead to stack corruption during link reset.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ac4cbedfdf upstream.
There are still a couple of minor issues in the X.509 leap year handling:
(1) To avoid doing a modulus-by-400 in addition to a modulus-by-100 when
determining whether the year is a leap year or not, I divided the year
by 100 after doing the modulus-by-100, thereby letting the compiler do
one instruction for both, and then did a modulus-by-4.
Unfortunately, I then passed the now-modified year value to mktime64()
to construct a time value.
Since this isn't a fast path and since mktime64() does a bunch of
divisions, just condense down to "% 400". It's also easier to read.
(2) The default month length for any February where the year doesn't
divide by four exactly is obtained from the month_length[] array where
the value is 29, not 28.
This is fixed by altering the table.
Reported-by: Rudolf Polzer <rpolzer@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b62917a262 upstream.
The change fixes potential oops while accessing iomem on invalid
address, if devm_ioremap_resource() fails due to some reason.
The devm_ioremap_resource() function returns ERR_PTR() and never
returns NULL, which makes useless a following check for NULL.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Fixes: 5a4eea2658 ("crypto: ux500 - Use devm_xxx() managed function")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b52d55f4f upstream.
The change fixes potential oops while accessing iomem on invalid
address, if devm_ioremap_resource() fails due to some reason.
The devm_ioremap_resource() function returns ERR_PTR() and never
returns NULL, which makes useless a following check for NULL.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Fixes: b0e8b3417a ("crypto: atmel - use devm_xxx() managed function")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b8b28fd23 upstream.
We're clearing the wrong memory. The memory corruption is likely
harmless because we weren't going to use that stack memory again but not
zeroing is a potential information leak.
Fixes: e28facde3c ('crypto: keywrap - add key wrapping block chaining mode')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce0ae266fe upstream.
Since a crypto_ahash_import() can be called against a request context
that has not had a crypto_ahash_init() performed, the request context
needs to be cleared to insure there is no random data present. If not,
the random data can result in a kernel oops during crypto_ahash_update().
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b31dde2a5c upstream.
Use a local variable for the exported and imported state so that
alignment is not an issue. On export, set a local variable from the
request context and then memcpy the contents of the local variable to
the export memory area. On import, memcpy the import memory area into
a local variable and then use the local variable to set the request
context.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d1662165ae upstream.
Since the exported information can be exposed to user-space, instead of
exporting the entire request context only export the minimum information
needed.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 952bce9792 upstream.
Commit 8996eafdcb ("crypto: ahash - ensure statesize is non-zero")
added a check to prevent ahash algorithms from successfully registering
if the import and export functions were not implemented. This prevents
an oops in the hash_accept function of algif_hash. This commit causes
the ccp-crypto module SHA support and AES CMAC support from successfully
registering and causing the ccp-crypto module load to fail because the
ahash import and export functions are not implemented.
Update the CCP Crypto API support to provide import and export support
for ahash algorithms.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 836b34a935 upstream.
create_fixed_stream_quirk(), snd_usb_parse_audio_interface() and
create_uaxx_quirk() functions allocate the audioformat object by themselves
and free it upon error before returning. However, once the object is linked
to a stream, it's freed again in snd_usb_audio_pcm_free(), thus it'll be
double-freed, eventually resulting in a memory corruption.
This patch fixes these failures in the error paths by unlinking the audioformat
object before freeing it.
Based on a patch by Takashi Iwai <tiwai@suse.de>
[Note for stable backports:
this patch requires the commit 902eb7fd1e ('ALSA: usb-audio: Minor
code cleanup in create_fixed_stream_quirk()')]
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1283358
Reported-by: Ralf Spenneberg <ralf@spenneberg.net>
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0ef21100ae upstream.
The Microsoft HD-5001 webcam microphone does not support sample rate
reading as the HD-5000 one.
This results in dmesg errors and sound hanging with pulseaudio.
Signed-off-by: Victor Clément <victor.clement@openmailbox.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 447d6275f0 upstream.
Add some sanity check codes before actually accessing the endpoint via
get_endpoint() in order to avoid the invalid access through a
malformed USB descriptor. Mostly just checking bNumEndpoints, but in
one place (snd_microii_spdif_default_get()), the validity of iface and
altsetting index is checked as well.
Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=971125
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f886ca127 upstream.
create_fixed_stream_quirk() may cause a NULL-pointer dereference by
accessing the non-existing endpoint when a USB device with a malformed
USB descriptor is used.
This patch avoids it simply by adding a sanity check of bNumEndpoints
before the accesses.
Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=971125
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9c6ba45671 upstream.
The powermate driver expects at least one valid USB endpoint in its
probe function. If given malicious descriptors that specify 0 for
the number of endpoints, it will crash. Validate the number of
endpoints on the interface before using them.
The full report for this issue can be found here:
http://seclists.org/bugtraq/2016/Mar/85
Reported-by: Ralf Spenneberg <ralf@spenneberg.net>
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea6db90e75 upstream.
A Fedora user reports that the ftdi_sio driver works properly for the
ICP DAS I-7561U device. Further, the user manual for these devices
instructs users to load the driver and add the ids using the sysfs
interface.
Add support for these in the driver directly so that the devices work
out of the box instead of needing manual configuration.
Reported-by: <thesource@mail.ru>
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e9a0b0525 upstream.
An attack using the lack of sanity checking in probe is known. This
patch checks for the existence of a second port.
CVE-2016-3136
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
[johan: add error message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0b818e3956 upstream.
Attacks that trick drivers into passing a NULL pointer
to usb_driver_claim_interface() using forged descriptors are
known. This thwarts them by sanity checking.
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4ec0ef3a82 upstream.
The iowarrior driver expects at least one valid endpoint. If given
malicious descriptors that specify 0 for the number of endpoints,
it will crash in the probe function. Ensure there is at least
one endpoint on the interface before using it.
The full report of this issue can be found here:
http://seclists.org/bugtraq/2016/Mar/87
Reported-by: Ralf Spenneberg <ralf@spenneberg.net>
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8835ba4a39 upstream.
An attack has become available which pretends to be a quirky
device circumventing normal sanity checks and crashes the kernel
by an insufficient number of interfaces. This patch adds a check
to the code path for quirky devices.
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 55ff8cfbc4 upstream.
The uas driver can never queue more then MAX_CMNDS (- 1) tags and tags
are shared between luns, so there is no need to claim that we can_queue
some random large number.
Not claiming that we can_queue 65536 commands, fixes the uas driver
failing to initialize while allocating the tag map with a "Page allocation
failure (order 7)" error on systems which have been running for a while
and thus have fragmented memory.
Reported-and-tested-by: Yves-Alexis Perez <corsac@corsac.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0d5ce778c4 upstream.
A typo of j for i led to a logic bug. To rule out future
confusion, the variable names are made meaningful.
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 264904ccc3 upstream.
Some devices I got show an inability to operate right after
power on if they are already connected. They are beyond recovery
if the descriptors are requested multiple times. So in case of
a timeout we rather bail early and reset again. But it must be
done only on the first loop lest we get into a reset/time out
spiral that can be overcome with a retry.
This patch is a rework of a patch that fell through the cracks.
http://www.spinics.net/lists/linux-usb/msg103263.html
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 98dbc9c6c6 upstream.
An "old" (.request_fn) DM 'struct request' stores a pointer to the
associated 'struct dm_rq_target_io' in rq->special.
dm_requeue_original_request(), previously named
dm_requeue_unmapped_original_request(), called dm_unprep_request() to
reset rq->special to NULL. But rq_end_stats() would go on to hit a NULL
pointer deference because its call to tio_from_request() returned NULL.
Fix this by calling rq_end_stats() _before_ dm_unprep_request()
Signed-off-by: Bryn M. Reeves <bmr@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Fixes: e262f34741 ("dm stats: add support for request-based DM devices")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d14fcf3dd7 upstream.
Otherwise operations may be attempted that will only ever go on to crash
(since the metadata device is either missing or unreliable if 'fail_io'
is set).
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2eae9e4489 upstream.
If a transaction abort has failed then we can no longer use the metadata
device. Typically this happens if the superblock is unreadable.
This fix addresses a crash seen during metadata device failure testing.
Fixes: 8a01a6af75 ("dm thin: prefetch missing metadata pages")
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6acfe68bac upstream.
Request-based DM's blk-mq support (dm-mq) was reported to be 50% slower
than if an underlying null_blk device were used directly. One of the
reasons for this drop in performance is that blk_insert_clone_request()
was calling blk_mq_insert_request() with @async=true. This forced the
use of kblockd_schedule_delayed_work_on() to run the blk-mq hw queues
which ushered in ping-ponging between process context (fio in this case)
and kblockd's kworker to submit the cloned request. The ftrace
function_graph tracer showed:
kworker-2013 => fio-12190
fio-12190 => kworker-2013
...
kworker-2013 => fio-12190
fio-12190 => kworker-2013
...
Fixing blk_insert_clone_request()'s blk_mq_insert_request() call to
_not_ use kblockd to submit the cloned requests isn't enough to
eliminate the observed context switches.
In addition to this dm-mq specific blk-core fix, there are 2 DM core
fixes to dm-mq that (when paired with the blk-core fix) completely
eliminate the observed context switching:
1) don't blk_mq_run_hw_queues in blk-mq request completion
Motivated by desire to reduce overhead of dm-mq, punting to kblockd
just increases context switches.
In my testing against a really fast null_blk device there was no benefit
to running blk_mq_run_hw_queues() on completion (and no other blk-mq
driver does this). So hopefully this change doesn't induce the need for
yet another revert like commit 621739b00e !
2) use blk_mq_complete_request() in dm_complete_request()
blk_complete_request() doesn't offer the traditional q->mq_ops vs
.request_fn branching pattern that other historic block interfaces
do (e.g. blk_get_request). Using blk_mq_complete_request() for
blk-mq requests is important for performance. It should be noted
that, like blk_complete_request(), blk_mq_complete_request() doesn't
natively handle partial completions -- but the request-based
DM-multipath target does provide the required partial completion
support by dm.c:end_clone_bio() triggering requeueing of the request
via dm-mpath.c:multipath_end_io()'s return of DM_ENDIO_REQUEUE.
dm-mq fix#2 is _much_ more important than #1 for eliminating the
context switches.
Before: cpu : usr=15.10%, sys=59.39%, ctx=7905181, majf=0, minf=475
After: cpu : usr=20.60%, sys=79.35%, ctx=2008, majf=0, minf=472
With these changes multithreaded async read IOPs improved from ~950K
to ~1350K for this dm-mq stacked on null_blk test-case. The raw read
IOPs of the underlying null_blk device for the same workload is ~1950K.
Fixes: 7fb4898e0 ("block: add blk-mq support to blk_insert_cloned_request()")
Fixes: bfebd1cdb ("dm: add full blk-mq support to request-based DM")
Reported-by: Sagi Grimberg <sagig@dev.mellanox.co.il>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07accfa9d1 upstream.
Code attempts to prevent certain IOCTL DSM from being called
when device is opened read only. This security feature can
be trivially overcome by changing the size portion of the
ioctl_command which isn't used.
Check only the _IOC_NR (i.e. the command).
Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5a51a7abca upstream.
We were setting the queue depth correctly, then setting it back to
two. If you hit this as a bisection point then please send me an email
as it would imply we've been hiding other bugs with this one.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff06c5ffbc upstream.
Commit 3209f9d780 ("scsi: storvsc: Fix a bug in the handling of SRB
status flags") filtered SRB_STATUS_AUTOSENSE_VALID out effectively making
the (SRB_STATUS_ABORTED | SRB_STATUS_AUTOSENSE_VALID) case a dead code. The
logic from this branch (e.g. storvsc_device_scan() call) is still required,
fix the check.
Fixes: 3209f9d780 ("scsi: storvsc: Fix a bug in the handling of SRB status flags")
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d5dbec3bc upstream.
This bug causes the wrong command to have its sense pointer overwritten,
which sometimes leads to a NULL pointer deref. Fix this by checking which
command is being requeued before restoring the scsi_eh_save data.
It turns out that some targets will disconnect a REQUEST SENSE command.
The autosense algorithm doesn't anticipate this. Hence multiple commands
can end up undergoing autosense simultaneously, and they will all try to
use the same scsi_eh_save struct, which won't work. Defer autosense when
the scsi_eh_save storage is in use by another command.
Fixes: f27db8eb98 ("ncr5380: Fix autosense bugs")
Reported-and-tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc18396528 upstream.
The list structures and related logic used in the NCR5380 driver mean that
a command cannot be queued twice (i.e. can't appear on more than one queue
and can't appear on the same queue more than once).
The abort handler must forget the command so that the mid-layer can re-use
it. E.g. the ML may send it back to the LLD via via scsi_eh_get_sense().
Fix this and also fix two error paths, so that commands get forgotten iff
completed.
Fixes: 8b00c3d5d4 ("ncr5380: Implement new eh_abort_handler")
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 71a00593ec upstream.
Calling NCR5380_select() from the abort handler causes various problems.
Firstly, it means potentially re-entering NCR5380_select(). Secondly, it
means that the lock is released, which permits the EH handlers to be
re-entered. The combination results in crashes. Don't do it.
Fixes: 8b00c3d5d4 ("ncr5380: Implement new eh_abort_handler")
Reported-and-tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1678847ec9 upstream.
The calls to NCR5380_transfer_pio() for DATA IN and DATA OUT phases will
modify cmd->SCp.this_residual, cmd->SCp.ptr and cmd->SCp.buffer. That
works as long as EH does not intervene, which became possible in
atari_NCR5380.c when I changed the locking to bring it closer to
NCR5380.c.
If error recovery aborts the command, the scsi_cmnd in question and its
buffer will be returned to the mid-layer. So the transfer has to cease,
but it can't be stopped by the initiator because the target controls the
bus phase.
The problem does not arise if the lock is not released. That was fine for
atari_scsi, because it implements DMA. For the other drivers, we have to
release the lock and re-enable interrupts for long PIO data transfers.
The solution is to split the transfer into small chunks. In between chunks
the main loop releases the lock and re-enables interrupts. Thus interrupts
can be serviced and eh_bus_reset_handler can intervene if need be.
This fixes an oops in NCR5380_transfer_pio() that can happen when the EH
abort handler is invoked during DATA IN or DATA OUT phase.
Fixes: 11d2f63b9c ("ncr5380: Change instance->host_lock to hostdata->lock")
Reported-and-tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1884c2838f upstream.
Commands subject to exception handling are to be returned to the scsi
mid-layer. Make sure that the various command pointers and command lists
in the low-level driver are correctly cleansed of affected commands.
This fixes some bugs that I accidentally introduced in v4.5-rc1 including
the removal of INIT_LIST_HEAD for the 'autosense' and 'disconnected'
command lists, and the possible NULL pointer dereference in
NCR5380_bus_reset() that was reported by Dan Carpenter.
hostdata->sensing may also point to an affected command so this pointer
also has to be cleared. The abort handler calls complete_cmd() to take
care of this; let's have the bus reset handler do the same.
The issue queue may also contain an affected command. If so, remove it.
This also follows the abort handler logic.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 62717f537e ("ncr5380: Implement new eh_bus_reset_handler")
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ecc479e00d upstream.
During EEH recovery number of online CPU's might change thereby changing
the number of MSIx vectors. Since each fib is allocated to a vector,
changes in the number of vectors causes fib to be sent thru invalid
vectors.In addition the correct number of MSIx vectors is not updated in
the INIT struct sent to the controller, when it is reinitialized.
Fixed by reassigning vectors to fibs based on the updated number of MSIx
vectors and updating the INIT structure before sending to controller.
Fixes: MSI-X vector calculation for suspend/resume
Signed-off-by: Raghava Aditya Renukunta <raghavaaditya.renukunta@pmcs.com>
Reviewed-by: Shane Seymour <shane.seymour@hpe.com>
Reviewed-by: Johannes Thumshirn <jthushirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f88fa79a61 upstream.
aac_fib_map_free() calls pci_free_consistent() without checking that
dev->hw_fib_va is not NULL and dev->max_fib_size is not zero.If they are
indeed NULL/0, this will result in a hang as pci_free_consistent() will
attempt to invalidate cache for the entire 64-bit address space
(which would take a very long time).
Fixed by adding a check to make sure that dev->hw_fib_va and
dev->max_fib_size are not NULL and 0 respectively.
Fixes: 9ad5204d6 - "[SCSI]aacraid: incorrect dma mapping mask during blinked recover or user initiated reset"
Signed-off-by: Raghava Aditya Renukunta <raghavaaditya.renukunta@pmcs.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f4ce057d5 upstream.
The driver utilizes an array of atomic variables to keep track of IO
submissions to each vector. To submit an IO multiple threads iterate
through the array to find a vector which has empty slots to send an
IO. The reading and updating of the variable is not atomic, causing race
conditions when a thread uses a full vector to submit an IO.
Fixed by mapping each FIB to a vector, the submission path then uses
said vector to submit IO thereby removing the possibly of a race
condition.The vector assignment is started from 1 since vector 0 is
reserved for the use of AIF management FIBS.If the number of MSIx
vectors is 1 (MSI or INTx mode) then all the fibs are allocated to
vector 0.
Fixes: 495c0217 "aacraid: MSI-x support"
Signed-off-by: Raghava Aditya Renukunta <raghavaaditya.renukunta@pmcs.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ecee0a3ee upstream.
One of the strange things that the original sg driver did was let the
user provide both a data-out buffer (it followed the sg_header+cdb)
_and_ specify a reply length greater than zero. What happened was that
the user data-out buffer was copied into some kernel buffers and then
the mid level was told a read type operation would take place with the
data from the device overwriting the same kernel buffers. The user would
then read those kernel buffers back into the user space.
From what I can tell, the above action was broken by commit fad7f01e61
("sg: set dxferp to NULL for READ with the older SG interface") in 2008
and syzkaller found that out recently.
Make sure that a user space pointer is passed through when data follows
the sg_header structure and command. Fix the abnormal case when a
non-zero reply_len is also given.
Fixes: fad7f01e61
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7834c10313 upstream.
Since 4.4, I've been able to trigger this occasionally:
===============================
[ INFO: suspicious RCU usage. ]
4.5.0-rc7-think+ #3 Not tainted
Cc: Andi Kleen <ak@linux.intel.com>
Link: http://lkml.kernel.org/r/20160315012054.GA17765@codemonkey.org.uk
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-------------------------------
./arch/x86/include/asm/msr-trace.h:47 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
RCU used illegally from idle CPU!
rcu_scheduler_active = 1, debug_locks = 1
RCU used illegally from extended quiescent state!
no locks held by swapper/3/0.
stack backtrace:
CPU: 3 PID: 0 Comm: swapper/3 Not tainted 4.5.0-rc7-think+ #3
ffffffff92f821e0 1f3e5c340597d7fc ffff880468e07f10 ffffffff92560c2a
ffff880462145280 0000000000000001 ffff880468e07f40 ffffffff921376a6
ffffffff93665ea0 0000cc7c876d28da 0000000000000005 ffffffff9383dd60
Call Trace:
<IRQ> [<ffffffff92560c2a>] dump_stack+0x67/0x9d
[<ffffffff921376a6>] lockdep_rcu_suspicious+0xe6/0x100
[<ffffffff925ae7a7>] do_trace_write_msr+0x127/0x1a0
[<ffffffff92061c83>] native_apic_msr_eoi_write+0x23/0x30
[<ffffffff92054408>] smp_trace_call_function_interrupt+0x38/0x360
[<ffffffff92d1ca60>] trace_call_function_interrupt+0x90/0xa0
<EOI> [<ffffffff92ac5124>] ? cpuidle_enter_state+0x1b4/0x520
Move the entering_irq() call before ack_APIC_irq(), because entering_irq()
tells the RCU susbstems to end the extended quiescent state, so that the
following trace call in ack_APIC_irq() works correctly.
Suggested-by: Andi Kleen <ak@linux.intel.com>
Fixes: 4787c368a9 "x86/tracing: Add irq_enter/exit() in smp_trace_reschedule_interrupt()"
Signed-off-by: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
commit 551adc6057 upstream.
Harry reported, that he's able to trigger a system freeze with cpu hot
unplug. The freeze turned out to be a live lock caused by recent changes in
irq_force_complete_move().
When fixup_irqs() and from there irq_force_complete_move() is called on the
dying cpu, then all other cpus are in stop machine an wait for the dying cpu
to complete the teardown. If there is a move of an interrupt pending then
irq_force_complete_move() sends the cleanup IPI to the cpus in the old_domain
mask and waits for them to clear the mask. That's obviously impossible as
those cpus are firmly stuck in stop machine with interrupts disabled.
I should have known that, but I completely overlooked it being concentrated on
the locking issues around the vectors. And the existance of the call to
__irq_complete_move() in the code, which actually sends the cleanup IPI made
it reasonable to wait for that cleanup to complete. That call was bogus even
before the recent changes as it was just a pointless distraction.
We have to look at two cases:
1) The move_in_progress flag of the interrupt is set
This means the ioapic has been updated with the new vector, but it has not
fired yet. In theory there is a race:
set_ioapic(new_vector) <-- Interrupt is raised before update is effective,
i.e. it's raised on the old vector.
So if the target cpu cannot handle that interrupt before the old vector is
cleaned up, we get a spurious interrupt and in the worst case the ioapic
irq line becomes stale, but my experiments so far have only resulted in
spurious interrupts.
But in case of cpu hotplug this should be a non issue because if the
affinity update happens right before all cpus rendevouz in stop machine,
there is no way that the interrupt can be blocked on the target cpu because
all cpus loops first with interrupts enabled in stop machine, so the old
vector is not yet cleaned up when the interrupt fires.
So the only way to run into this issue is if the delivery of the interrupt
on the apic/system bus would be delayed beyond the point where the target
cpu disables interrupts in stop machine. I doubt that it can happen, but at
least there is a theroretical chance. Virtualization might be able to
expose this, but AFAICT the IOAPIC emulation is not as stupid as the real
hardware.
I've spent quite some time over the weekend to enforce that situation,
though I was not able to trigger the delayed case.
2) The move_in_progress flag is not set and the old_domain cpu mask is not
empty.
That means, that an interrupt was delivered after the change and the
cleanup IPI has been sent to the cpus in old_domain, but not all CPUs have
responded to it yet.
In both cases we can assume that the next interrupt will arrive on the new
vector, so we can cleanup the old vectors on the cpus in the old_domain cpu
mask.
Fixes: 98229aa36c "x86/irq: Plug vector cleanup race"
Reported-by: Harry Junior <harryjr@outlook.fr>
Tested-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Joe Lawrence <joe.lawrence@stratus.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Ben Hutchings <ben@decadent.org.uk>
Link: http://lkml.kernel.org/r/alpine.DEB.2.11.1603140931430.3657@nanos
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a2e7aab4f upstream.
The [0 - 64k] ACPI PCI IO port resource boundary check in:
acpi_dev_ioresource_flags()
is currently applied blindly in the ACPI resource parsing to all
architectures, but only x86 suffers from that IO space limitation.
On arches (ie IA64 and ARM64) where IO space is memory mapped,
the PCI root bridges IO resource windows are firstly initialized from
the _CRS (in acpi_decode_space()) and contain the CPU physical address
at which a root bridge decodes IO space in the CPU physical address
space with the offset value representing the offset required to translate
the PCI bus address into the CPU physical address.
The IO resource windows are then parsed and updated in arch code
before creating and enumerating PCI buses (eg IA64 add_io_space())
to map in an arch specific way the obtained CPU physical address range
to a slice of virtual address space reserved to map PCI IO space,
ending up with PCI bridges resource windows containing IO
resources like the following on a working IA64 configuration:
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [io 0x1000000-0x100ffff window] (bus
address [0x0000-0xffff])
pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000fffff window]
pci_bus 0000:00: root bus resource [mem 0x80000000-0x8fffffff window]
pci_bus 0000:00: root bus resource [mem 0x80004000000-0x800ffffffff window]
pci_bus 0000:00: root bus resource [bus 00]
This implies that the [0 - 64K] check in acpi_dev_ioresource_flags()
leaves platforms with memory mapped IO space (ie IA64) broken (ie kernel
can't claim IO resources since the host bridge IO resource is disabled
and discarded by ACPI core code, see log on IA64 with missing root bridge
IO resource, silently filtered by current [0 - 64k] check in
acpi_dev_ioresource_flags()):
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000fffff window]
pci_bus 0000:00: root bus resource [mem 0x80000000-0x8fffffff window]
pci_bus 0000:00: root bus resource [mem 0x80004000000-0x800ffffffff window]
pci_bus 0000:00: root bus resource [bus 00]
[...]
pci 0000:00:03.0: [1002:515e] type 00 class 0x030000
pci 0000:00:03.0: reg 0x10: [mem 0x80000000-0x87ffffff pref]
pci 0000:00:03.0: reg 0x14: [io 0x1000-0x10ff]
pci 0000:00:03.0: reg 0x18: [mem 0x88020000-0x8802ffff]
pci 0000:00:03.0: reg 0x30: [mem 0x88000000-0x8801ffff pref]
pci 0000:00:03.0: supports D1 D2
pci 0000:00:03.0: can't claim BAR 1 [io 0x1000-0x10ff]: no compatible
bridge window
For this reason, the IO port resources boundaries check in generic ACPI
parsing code should be guarded with a CONFIG_X86 guard so that more arches
(ie ARM64) can benefit from the generic ACPI resources parsing interface
without incurring in unexpected resource filtering, fixing at the same
time current breakage on IA64.
This patch factors out IO ports boundary [0 - 64k] check in generic ACPI
code and makes the IO space check X86 specific to make sure that IO
space resources are usable on other arches too.
Fixes: 3772aea7d6 (ia64/PCI/ACPI: Use common ACPI resource parsing interface for host bridge)
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c7e3306d2 upstream.
The DT bindings for pinctrl-bcm2835 allow both the function and pull
to contain either one entry or one per pin. However, an error in the
DT parsing can cause failures if the number of pulls differs from the
number of functions.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 80c544ded2 upstream.
The function measurement block must not cross a page boundary. Ensure
that by raising the alignment requirement to the smallest power of 2
larger than the size of the fmb.
Fixes: d0b088531 ("s390/pci: performance statistics and debug infrastructure")
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f100bb1ff upstream.
Add the missing lpp magic initialization for cpu 0. Without this all
samples on cpu 0 do not have the most significant bit set in the
program parameter field, which we use to distinguish between guest and
host samples if the pid is also 0.
We did initialize the lpp magic in the absolute zero lowcore but
forgot that when switching to the allocated lowcore on cpu 0 only.
Reported-by: Shu Juan Zhang <zhshuj@cn.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Fixes: e22cf8ca6f ("s390/cpumf: rework program parameter setting to detect guest samples")
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e370e47694 upstream.
There is a tricky interaction between the machine check handler
and the critical sections of load_fpu_regs and save_fpu_regs
functions. If the machine check interrupts one of the two
functions the critical section cleanup will complete the function
before the machine check handler s390_do_machine_check is called.
Trouble is that the machine check handler needs to validate the
floating point registers *before* and not *after* the completion
of load_fpu_regs/save_fpu_regs.
The simplest solution is to rewind the PSW to the start of the
load_fpu_regs/save_fpu_regs and retry the function after the
return from the machine check handler.
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eb1af3b71f upstream.
Large memory Haswell-EX systems with multiple DIMMs per channel were
sometimes reporting the wrong DIMM.
Found three problems:
1) Debug printouts for socket and channel interleave were not interpreting
the register fields correctly. The socket interleave field is a 2^X
value (0=1, 1=2, 2=4, 3=8). The channel interleave is X+1 (0=1, 1=2,
2=3. 3=4).
2) Actual use of the socket interleave value didn't interpret as 2^X
3) Conversion of address to channel address was complicated, and wrong.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Acked-by: Aristeu Rozanski <arozansk@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-edac@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b15d53d009 upstream.
kmap_coherent needs disabled preemption to not schedule in the critical
section, just like kmap_coherent on mips and kmap_atomic in general.
Fixes: 8222dbe21e "sched/preempt, mm/fault: Decouple preemption from the page fault logic"
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Rich Felker <dalias@libc.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9c904b761 upstream.
The callers of steal_account_process_tick() expect it to return
whether a jiffy should be considered stolen or not.
Currently the return value of steal_account_process_tick() is in
units of cputime, which vary between either jiffies or nsecs
depending on CONFIG_VIRT_CPU_ACCOUNTING_GEN.
If cputime has nsecs granularity and there is a tiny amount of
stolen time (a few nsecs, say) then we will consider the entire
tick stolen and will not account the tick on user/system/idle,
causing /proc/stats to show invalid data.
The fix is to change steal_account_process_tick() to accumulate
the stolen time and only account it once it's worth a jiffy.
(Thanks to Frederic Weisbecker for suggestions to fix a bug in my
first version of the patch.)
Signed-off-by: Chris Friesen <chris.friesen@windriver.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/56DBBDB8.40305@mail.usask.ca
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81ad4276b5 upstream.
In some cases, platform thermal driver may report invalid trip points,
thermal core should not take any action for these trip points.
This fixed a regression that bogus trip point starts to screw up thermal
control on some Lenovo laptops, after
commit bb431ba26c
Author: Zhang Rui <rui.zhang@intel.com>
Date: Fri Oct 30 16:31:47 2015 +0800
Thermal: initialize thermal zone device correctly
After thermal zone device registered, as we have not read any
temperature before, thus tz->temperature should not be 0,
which actually means 0C, and thermal trend is not available.
In this case, we need specially handling for the first
thermal_zone_device_update().
Both thermal core framework and step_wise governor is
enhanced to handle this. And since the step_wise governor
is the only one that uses trends, so it's the only thermal
governor that needs to be updated.
Tested-by: Manuel Krause <manuelkrause@netscape.net>
Tested-by: szegad <szegadlo@poczta.onet.pl>
Tested-by: prash <prash.n.rao@gmail.com>
Tested-by: amish <ammdispose-arch@yahoo.com>
Tested-by: Matthias <morpheusxyz123@yahoo.de>
Reviewed-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1317190
Link: https://bugzilla.kernel.org/show_bug.cgi?id=114551
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67d5268908 upstream.
The util/python-ext-sources file contains source files required to build
the python extension relative to $(srctree)/tools/perf,
Such a file path $(FILE).c is handed over to the python extension build
system, which builds the final object in the
$(PYTHON_EXTBUILD)/tmp/$(FILE).o path.
After the build is done all files from $(PYTHON_EXTBUILD)lib/ are
carried as the result binaries.
Above system fails when we add source file relative to ../lib, which we
do for:
../lib/bitmap.c
../lib/find_bit.c
../lib/hweight.c
../lib/rbtree.c
All above objects will be built like:
$(PYTHON_EXTBUILD)/tmp/../lib/bitmap.c
$(PYTHON_EXTBUILD)/tmp/../lib/find_bit.c
$(PYTHON_EXTBUILD)/tmp/../lib/hweight.c
$(PYTHON_EXTBUILD)/tmp/../lib/rbtree.c
which accidentally happens to be final library path:
$(PYTHON_EXTBUILD)/lib/
Changing setup.py to pass full paths of source files to Extension build
class and thus keep all built objects under $(PYTHON_EXTBUILD)tmp
directory.
Reported-by: Jeff Bastian <jbastian@redhat.com>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Josh Boyer <jwboyer@fedoraproject.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20160227201350.GB28494@krava.redhat.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 940db6dcd3 upstream.
When an error happens during alias parsing currently the complete
parsing of all attributes of the PMU is stopped. This is breaks old perf
on a newer kernel that may have not-yet-know alias attributes (such as
.scale or .per-pkg).
Continue when some attribute is unparseable.
This is IMHO a stable candidate and should be backported to older
versions to avoid problems with newer kernels.
v2: Print warnings when something goes wrong.
v3: Change warning to debug output
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Link: http://lkml.kernel.org/r/1455749095-18358-1-git-send-email-andi@firstfloor.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef697a712a upstream.
Old KVM guests invoke single-context invvpid without actually checking
whether it is supported. This was fixed by commit 518c8ae ("KVM: VMX:
Make sure single type invvpid is supported before issuing invvpid
instruction", 2010-08-01) and the patch after, but pre-2.6.36
kernels lack it including RHEL 6.
Reported-by: jmontleo@redhat.com
Tested-by: jmontleo@redhat.com
Fixes: 99b83ac893
Reviewed-by: David Matlack <dmatlack@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9ad4ec837 upstream.
Moving the initialization earlier is needed in 4.6 because
kvm_arch_init_vm is now using mmu_lock, causing lockdep to
complain:
[ 284.440294] INFO: trying to register non-static key.
[ 284.445259] the code is fine but needs lockdep annotation.
[ 284.450736] turning off the locking correctness validator.
...
[ 284.528318] [<ffffffff810aecc3>] lock_acquire+0xd3/0x240
[ 284.533733] [<ffffffffa0305aa0>] ? kvm_page_track_register_notifier+0x20/0x60 [kvm]
[ 284.541467] [<ffffffff81715581>] _raw_spin_lock+0x41/0x80
[ 284.546960] [<ffffffffa0305aa0>] ? kvm_page_track_register_notifier+0x20/0x60 [kvm]
[ 284.554707] [<ffffffffa0305aa0>] kvm_page_track_register_notifier+0x20/0x60 [kvm]
[ 284.562281] [<ffffffffa02ece70>] kvm_mmu_init_vm+0x20/0x30 [kvm]
[ 284.568381] [<ffffffffa02dbf7a>] kvm_arch_init_vm+0x1ea/0x200 [kvm]
[ 284.574740] [<ffffffffa02bff3f>] kvm_dev_ioctl+0xbf/0x4d0 [kvm]
However, it also helps fixing a preexisting problem, which is why this
patch is also good for stable kernels: kvm_create_vm was incrementing
current->mm->mm_count but not decrementing it at the out_err label (in
case kvm_init_mmu_notifier failed). The new initialization order makes
it possible to add the required mmdrop without adding a new error label.
Reported-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7dd0fdff14 upstream.
Discard policy uses ack_notifiers to prevent injection of PIT interrupts
before EOI from the last one.
This patch changes the policy to always try to deliver the interrupt,
which makes a difference when its vector is in ISR.
Old implementation would drop the interrupt, but proposed one injects to
IRR, like real hardware would.
The old policy breaks legacy NMI watchdogs, where PIT is used through
virtual wire (LVT0): PIT never sends an interrupt before receiving EOI,
thus a guest deadlock with disabled interrupts will stop NMIs.
Note that NMI doesn't do EOI, so PIT also had to send a normal interrupt
through IOAPIC. (KVM's PIT is deeply rotten and luckily not used much
in modern systems.)
Even though there is a chance of regressions, I think we can fix the
LVT0 NMI bug without introducing a new tick policy.
Reported-by: Yuki Shibuya <shibuya.yk@ncos.nec.co.jp>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b894157145 upstream.
The Home Agent and PCU PCI devices in Broadwell-EP have a non-BAR register
where a BAR should be. We don't know what the side effects of sizing the
"BAR" would be, and we don't know what address space the "BAR" might appear
to describe.
Mark these devices as having non-compliant BARs so the PCI core doesn't
touch them.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b84106b4e2 upstream.
The PCI config header (first 64 bytes of each device's config space) is
defined by the PCI spec so generic software can identify the device and
manage its usage of I/O, memory, and IRQ resources.
Some non-spec-compliant devices put registers other than BARs where the
BARs should be. When the PCI core sizes these "BARs", the reads and writes
it does may have unwanted side effects, and the "BAR" may appear to
describe non-sensical address space.
Add a flag bit to mark non-compliant devices so we don't touch their BARs.
Turn off IO/MEM decoding to prevent the devices from consuming address
space, since we can't read the BARs to find out what that address space
would be.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
// Description: Overlay to enable the secondary memory interface peripheral
// Author: Luke Wren
/dts-v1/;
/plugin/;
/{
compatible = "brcm,bcm2708";
fragment@0 {
target = <&smi>;
__overlay__ {
pinctrl-names = "default";
pinctrl-0 = <&smi_pins>;
status = "okay";
};
};
fragment@1 {
target = <&gpio>;
__overlay__ {
smi_pins: smi_pins {
/* Don't configure the top two address bits, as
these are already used as ID_SD and ID_SC */
brcm,pins = <2 3 4 5 6 7 8 9 10 11 12 13 14 15
16 17 18 19 20 21 22 23 24 25>;
/* Alt 0: SMI */
brcm,function = <5 5 5 5 5 5 5 5 5 5 5 5 5 5 5
5 5 5 5 5 5 5 5 5>;
/* /CS, /WE and /OE are pulled high, as they are
generally active low signals */
brcm,pull = <2 2 2 2 2 2 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0>;
};
};
};
};
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
