On a Raspberry Pi 2, the lirc_rpi driver might receive spurious
interrupts and change it's low-active / high-active setting.
When this happens, the IR remote control stops working.
This patch disables this auto-detection if the 'sense' parameter
was set in the device tree, making the driver robust to such
spurious interrupts.
Claiming the completion_mutex within add_completion did prevent some
messages appearing twice, but provokes a deadlock caused by vcsm using
vchiq within a page fault handler.
Revert the use of completion_mutex, and instead fix the original
problem using more memory barriers.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
There is already an overlay for the mcp23017 I2C GPIO expander,
but it does nothing without the required driver module.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
commit cf5ef3a299 upstream.
This patch adds 32 bit word capability to the wm8731 driver. The wm8731
codec is capable of handling 32 bit word sizes, however that has not
previously been activated in the codec driver.
Signed-off-by: Matt Flax <flatmax@flatmax.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Support IQAudIO Digi board with iqaudio_digi machine driver and
iqaudio-digi-wm8804-audio overlay.
NB. Machine driver is a cut and paste of hifiberry_digi code, with format
and general cleanup to comply with kernel coding standards.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
1) Try to avoid reducing overclock when a card is removed.
2) Reset overclock on card insertion.
3) Reduce logging when errors occur, lowering the severity of
some messages and making others conditional on the debug
flag.
4) Attempt to identify a disconnected SD bus earlier, treating a
zero returned OCR (voltage support) as an error condition.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Backport of upstream commit f3a932baa7
See: https://github.com/raspberrypi/linux/issues/1534
--
This patch is based on https://patchwork.ozlabs.org/patch/574623/.
Tejun submitted commit 23d11a58a9 ("workqueue: skip flush dependency
checks for legacy workqueues") for the legacy create*_workqueue()
interface.
But some workq created by alloc_workqueue still reports warning on
memory reclaim, e.g nvme_workq with flag WQ_MEM_RECLAIM set:
workqueue: WQ_MEM_RECLAIM nvme:nvme_reset_work is flushing !WQ_MEM_RECLAIM events:lru_add_drain_per_cpu
------------[ cut here ]------------
WARNING: CPU: 0 PID: 6 at SoC/linux/kernel/workqueue.c:2448 check_flush_dependency+0xb4/0x10c
...
check_flush_dependency+0xb4/0x10c
flush_work+0x54/0x140
lru_add_drain_all+0x138/0x188
migrate_prep+0xc/0x18
alloc_contig_range+0xf4/0x350
cma_alloc+0xec/0x1e4
dma_alloc_from_contiguous+0x38/0x40
__dma_alloc+0x74/0x25c
nvme_alloc_queue+0xcc/0x36c
nvme_reset_work+0x5c4/0xda8
process_one_work+0x128/0x2ec
worker_thread+0x58/0x434
kthread+0xd4/0xe8
ret_from_fork+0x10/0x50
That's because lru_add_drain_all() will schedule the drain work on
system_wq, whose flag is set to 0, !WQ_MEM_RECLAIM.
Introduce a dedicated WQ_MEM_RECLAIM workqueue to do
lru_add_drain_all(), aiding in getting memory freed.
Link: http://lkml.kernel.org/r/1464917521-9775-1-git-send-email-shhuiw@foxmail.com
Signed-off-by: Wang Sheng-Hui <shhuiw@foxmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bluetooth on RPi 3 using uart1 will not work without setting core_freq=250 in config.txt. This is not
documented anywhere, so this seems like a good place to start.
This patch adds headphone and microphone capability to the Audio Injector sound card. The patch also sets the bit clock ratio for use in the bcm2835-i2s driver. The bcm2835-i2s can't handle an 8 kHz sample rate when the bit clock is at 12 MHz because its register is only 10 bits wide which can't represent the ch2 offset of 1508. For that reason, the rate constraint is added.
Add a sysfs-based FIQ latency profiler that times differences between
start-of-frame interrupts. Stats readout is via the sof_histogram
attribute.
Writing to the sof_histogram attribute resets the bucket counters.
The tx_status hook is supposed to be safe to call from interrupt
context, but it wouldn't ever return completion for the last transfer,
meaning you couldn't poll for DMA completion with interrupts masked.
This fixes IRQ handling for bcm2835's DSI1, which requires using the
DMA engine to write its registers due to a bug in the AXI bridge.
Signed-off-by: Eric Anholt <eric@anholt.net>
The current cyclic DMA period splitting implementation can generate
very small chunks at the end of each period. For example a 65536 byte
period will be split into a 65532 byte chunk and a 4 byte chunk on
the "lite" DMA channels.
This increases pressure on the RAM controller as the DMA controller
needs to fetch two control blocks from RAM in quick succession and
could potentially cause latency issues if the RAM is tied up by other
devices.
We can easily avoid these situations by distributing the remaining
length evenly between the last-but-one and the last chunk, making
sure that split chunks will be at least half the maximum length the
DMA controller can handle.
This patch checks if the last chunk would be less than half of
the maximum DMA length and if yes distributes the max len+4...max_len*1.5
bytes evenly between the last 2 chunks. This results in chunk sizes
between max_len/2 and max_len*0.75 bytes.
Signed-off-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Tested-by: Clive Messer <clive.messer@digitaldreamtime.co.uk>
The code responsible for splitting periods into chunks that
can be handled by the DMA controller missed to update total_len,
the number of bytes processed in the current period, when there
are more chunks to follow.
Therefore total_len was stuck at 0 and the code didn't work at all.
This resulted in a wrong control block layout and audio issues because
the cyclic DMA callback wasn't executing on period boundaries.
Fix this by adding the missing total_len update.
Signed-off-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Tested-by: Clive Messer <clive.messer@digitaldreamtime.co.uk>
Dma channel0 is used by the legacy api - to avoid confilcts this
needs to get masked out in the device-tree instead of hardcoding it
in the driver.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Load driver early since at least bcm2708_fb doesn't support deferred
probing and even if it did, we don't want the video driver deferred.
Support the legacy DMA API which is needed by bcm2708_fb
(but only using the dedicated dma channel 0).
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Use platform_get_irq_byname to allow for correct mapping of
interrupts to dma channels.
The currently implemented device tree is unfortunately
implemented with the wrong assumption, that each dma-channel
has its own dma channel, but dma-irq 11 is handling
dma-channel 11-14 and dma-irq 12 is actually a "catch all"
interrupt.
So here we use the byname variant and require that interrupts
are explicitly named via the interrupts-name property in the
device tree.
The use of shared interrupts is also implemented.
As a side-effect this means we can now use dma channels 12, 13 and 14
in a correct manner - also testing shows that onl using
channels 11 to 14 for spi and i2s works perfectly (when playing
some video)
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Eric Anholt <eric@anholt.net>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Also added check for an error condition in bcm2835_dma_create_cb_chain
that showed up during development of this patch.
Tested using dmatest for all enabled channels.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add slave_sg support to bcm2835-dma using shared allocation
code for bcm2835_desc and DMA-control blocks already used by
dma_cyclic.
Note that bcm2835_dma_callback had to get modified to support
both modes of operation (cyclic and non-cyclic).
Tested using:
* Hifiberry I2S card (using cyclic DMA)
* fb_st7735r SPI-framebuffer (using slave_sg DMA via spi-bcm2835)
playing BigBuckBunny for audio and video.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The bcm2835 dma system has 2 basic types of dma-channels:
* "normal" channels
* "light" channels
Lite channels are limited in several aspects:
* internal data-structure is 128 bit (not 256)
* does not support BCM2835_DMA_TDMODE (2D)
* DMA length register is limited to 16 bit.
so 0-65535 (not 0-65536 as mentioned in the official datasheet)
* BCM2835_DMA_S/D_IGNORE are not supported
The detection of the type of mode is implemented by looking at
the LITE bit in the DEBUG register for each channel.
This allows automatic detection.
Based on this the maximum block size is set to (64K - 4) or to 1G
and this limit is honored during generation of control block
chains. The effect is that when a LITE channel is used more
control blocks are used to do the same transfer (compared
to a normal channel).
As there are several sources/target DREQS that are 32 bit wide
we need to have the transfer to be a multiple of 4 as this would
break the transfer otherwise.
This is why the limit of (64K - 4) was chosen over the
alternative of (64K - 4K).
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In preparation of adding slave_sg functionality this patch moves the
generation/allocation of bcm2835_desc and the building of
the corresponding DMA-control-block chain from bcm2835_dma_prep_dma_cyclic
into the newly created method bcm2835_dma_create_cb_chain.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add additional defines describing the DMA registers
as well as adding some more documentation to those registers.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The original patch contained 3 dma channels that were masked out.
These - as far as research and discussions show - are a
artefacts remaining from the downstream legacy dma-api.
Right now down-stream still includes a legacy api used only
in a single (downstream only) driver (bcm2708_fb) that requires
2D DMA for speedup (DMA-channel 0).
Formerly the sd-card support driver also was using this legacy
api (DMA-channel 2), but since has been moved over to use
dmaengine directly.
The DMA-channel 3 is already masked out in the devicetree in
the default property "brcm,dma-channel-mask = <0x7f35>;"
So we can remove the whole masking of DMA channels.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Modify the i2c-gpio overlay to export symbol i2c-gpio for use by other
overlays. Export the alias as well for good measure.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The rpi-dac overlay is almost identical to the hifiberry-dac overlay -
the codec used is different but it also doesn't sit on the I2C bus. As
a result, when the overlays were modified for dynamic loading and it
was discovered that the hifiberry-dac overlay didn't work any more, the
the rpi-dac overlay was also broken.
The failure was caused by the fact that outside a bus, device names are
constructed from the concatenation of the path elements leading to it,
so moving the codec instantiation inside /soc caused the device name
to get a "soc" added, breaking ALSA's naming.
See: http://forum.kodi.tv/showthread.php?tid=269814&pid=2349776#pid2349776
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
There was a bug in the GPU firmware that had reversed these
two formats.
Detect the old firmware, and reverse the formats if necessary.
Signed-off-by: Dave Stevenson <6by9@users.noreply.github.com>
Contains the sound/soc/bcm ALSA machine driver and necessary alterations to the Kconfig and Makefile.
Adds the dts overlay and updates the Makefile and README.
Updates the relevant defconfig files to enable building for the Raspberry Pi.
Thanks to Phil Elwell (pelwell) for the review, simple-card concepts and discussion. Thanks to Clive Messer for overlay naming suggestions.
This commit adds basic support for the codec usage including: Device tree overlay,
binding I2S bus and setting I2S mode, clock source and frequency setting according
to spec.
Signed-off-by: Andrey Grodzovsky <andrey2805@gmail.com>
justboom-dac: Adjust for ALSA API change
As of 4.4, snd_soc_limit_volume now takes a struct snd_soc_card *
rather than a struct snd_soc_codec *.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Code ported from bcm2708-i2s driver in Raspberry Pi tree.
RPi commit 7ee829fd77 ("bcm2708-i2s:
Enable MMAP support via a DT property and overlay")
The i2s driver used to claim to support MMAP, but that feature was disabled
when some problems were found. Add the ability to enable this feature
through Device Tree, using the i2s-mmap overlay.
See: #1004
Signed-off-by: Matthias Reichl <hias@horus.com>
Code ported from bcm2708-i2s driver in Raspberry Pi tree.
RPi commit ba46b4935a ("ASoC: Add
support for BCM2708")
This driver adds support for digital audio (I2S)
for the BCM2708 SoC that is used by the
Raspberry Pi. External audio codecs can be
connected to the Raspberry Pi via P5 header.
It relies on cyclic DMA engine support for BCM2708.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
Signed-off-by: Matthias Reichl <hias@horus.com>
Code ported from bcm2708-i2s driver in Raspberry Pi tree.
RPi commit fd7d7a3dbe ("bcm2708:
Eliminate i2s debugfs directory error")
Qualify the two regmap ranges uses by bcm2708-i2s ('-i2s' and '-clk')
to avoid the name clash when registering debugfs entries.
Signed-off-by: Matthias Reichl <hias@horus.com>
Code ported from bcm2708-i2s driver in Raspberry Pi tree.
RPi commit c14827ecda ("bcm2708: Allow
option card devices to be configured via DT")
Original work by Zoltan Szenczi, committed to RPi tree by
Phil Elwell.
Signed-off-by: Matthias Reichl <hias@horus.com>
Code ported from bcm2708-i2s driver in Raspberry Pi tree.
RPi commit 62c05a0b53 ("ASoC: BCM2708:
Add 24 bit support")
This adds 24 bit support to the I2S driver of the BCM2708.
Besides enabling the 24 bit flags, it includes two bug fixes:
MMAP is not supported. Claiming this leads to strange issues
when the format of driver and file do not match.
The datasheet states that the width extension bit should be set
for widths greater than 24, but greater or equal would be correct.
This follows from the definition of the width field.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
RPi commit 3e8c672bc4 ("bcm2708-i2s:
Update bclk_ratio to more correct values")
Discussion about blck_ratio affecting sound quality:
https://github.com/raspberrypi/linux/issues/681
Signed-off-by: Matthias Reichl <hias@horus.com>
Code copied from spi-bcm2835. Get physical address from devicetree
instead of using hardcoded constant.
Signed-off-by: Matthias Reichl <hias@horus.com>
To speed testing of the new sdhost driver that adapts to changes in
core_freq, hack the on-demand governor to treat io_is_busy=1 as
io_is_busy=0. The io_is_busy feature can still be forced using
io_is_busy=2.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Commit 73345fd212:
brcmfmac: Configure country code using device specific settings
prevents region codes from working on devices that lack a region code
translation table. In the event of an absent table, preserve the old
behaviour of using the provided code as-is.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Disable wireless power saving in the brcmfmac WLAN driver. This is a
temporary measure until the connectivity loss resulting from power
saving is resolved.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
This is a port of Pantelis Antoniou's v3 port that makes use of the
new upstreamed configfs support for binary attributes.
Original commit message:
Add a runtime interface to using configfs for generic device tree overlay
usage. With it its possible to use device tree overlays without having
to use a per-platform overlay manager.
Please see Documentation/devicetree/configfs-overlays.txt for more info.
Changes since v2:
- Removed ifdef CONFIG_OF_OVERLAY (since for now it's required)
- Created a documentation entry
- Slight rewording in Kconfig
Changes since v1:
- of_resolve() -> of_resolve_phandles().
Originally-signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
DT configfs: Fix build errors on other platforms
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
DT configfs: fix build error
There is an error when compiling rpi-4.6.y branch:
CC drivers/of/configfs.o
drivers/of/configfs.c:291:21: error: initialization from incompatible pointer type [-Werror=incompatible-pointer-types]
.default_groups = of_cfs_def_groups,
^
drivers/of/configfs.c:291:21: note: (near initialization for 'of_cfs_subsys.su_group.default_groups.next')
The .default_groups is linked list since commit
1ae1602de0.
This commit uses configfs_add_default_group to fix this problem.
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Add non-mainline source for rtl8192cu wireless driver version v4.0.2_9000 as
this is widely used. Disable older rtlwifi driver.
8192cu needs old wireless extensions
The obsolete WIRELESS_EXT configuration is used
by the old Realtek code and is needed for AP support.
8192cu: CONFIG_AP_MODE hardcoded in autoconf.h
rtl8192c_rf6052: PHY_RFShadowRefresh(): fix off-by-one
Signed-off-by: Marc Kleine-Budde <mkl@blackshift.org>
rtl8192cu: Add PID for D-Link DWA 131
The pl011 driver looks for DT aliases of the form "serial<n>",
and if found uses <n> as the device ID. This can cause
/dev/ttyAMA0 to become /dev/ttyAMA1, which is confusing if the
other serial port is provided by the 8250 driver which doesn't
use the same logic.
Add a mailbox-driven backlight controller for the Raspberry Pi DSI
touchscreen display. Requires updated GPU firmware to recognise the
mailbox request.
Signed-off-by: Gordon Hollingworth <gordon@raspberrypi.org>
Signed-off-by: Jan Grulich <jan@grulich.eu>
config: fix RaspiDAC Rev.3x dependencies
Change depends to SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S
like the other I2S soundcard drivers.
Signed-off-by: Matthias Reichl <hias@horus.com>
The Raspberry Pi firmware manages the power-down and reboot
process. To do this it installs a pm_power_off handler, causing
the gpio-poweroff module to abort the probe function.
This patch introduces a "force" DT property that overrides that
behaviour, and also adds a DT overlay to enable and control it.
Note that running in an active-low configuration (DT parameter
"active_low") requires a custom dt-blob.bin and probably won't
allow a reboot without switching off, so an external inversion
of the trigger signal may be preferable.
Provide a __copy_from_user that uses memcpy. On BCM2708, use
optimised memcpy/memmove/memcmp/memset implementations.
arch/arm: Add mmiocpy/set aliases for memcpy/set
See: https://github.com/raspberrypi/linux/issues/1082
copy_from_user: CPU_SW_DOMAIN_PAN compatibility
The downstream copy_from_user acceleration must also play nice with
CONFIG_CPU_SW_DOMAIN_PAN.
See: https://github.com/raspberrypi/linux/issues/1381
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The driver contains a low-level hardware driver for the TAS5713 and the
drivers for the Raspberry Pi I2S subsystem.
TAS5713: return error if initialisation fails
Existing TAS5713 driver logs errors during initialisation, but does not return
an error code. Therefore even if initialisation fails, the driver will still be
loaded, but won't work. This patch fixes this. I2C communication error will now
reported correctly by a non-zero return code.
HiFiBerry Amp: fix device-tree problems
Some code to load the driver based on device-tree-overlays was missing. This is added by this patch.
The driver is based on the HiFiBerry DAC driver. However HiFiBerry DAC+ uses
a different codec chip (PCM5122), therefore a new driver is necessary.
Add support for the HiFiBerry DAC+ Pro.
The HiFiBerry DAC+ and DAC+ Pro products both use the existing bcm sound driver with the DAC+ Pro having a special clock device driver representing the two high precision oscillators.
An addition bug fix is included for the PCM512x codec where by the physical size of the sample frame is used in the calculation of the LRCK divisor as it was found to be wrong when using 24-bit depth sample contained in a little endian 4-byte sample frame.
Limit PCM512x "Digital" gain to 0dB by default with HiFiBerry DAC+
24db_digital_gain DT param can be used to specify that PCM512x
codec "Digital" volume control should not be limited to 0dB gain,
and if specified will allow the full 24dB gain.
Add dt param to force HiFiBerry DAC+ Pro into slave mode
"dtoverlay=hifiberry-dacplus,slave"
Add 'slave' param to use HiFiBerry DAC+ Pro in slave mode,
with Pi as master for bit and frame clock.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
Set a limit of 0dB on Digital Volume Control
The main volume control in the PCM512x DAC has a range up to
+24dB. This is dangerously loud and can potentially cause massive
clipping in the output stages. Therefore this sets a sensible
limit of 0dB for this control.
Allow up to 24dB digital gain to be applied when using IQAudIO DAC+
24db_digital_gain DT param can be used to specify that PCM512x
codec "Digital" volume control should not be limited to 0dB gain,
and if specified will allow the full 24dB gain.
Modify IQAudIO DAC+ ASoC driver to set card/dai config from dt
Add the ability to set the card name, dai name and dai stream name, from
dt config.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
Signed-off-by: Daniel Matuschek <daniel@matuschek.net>
Add a parameter to turn off SPDIF output if no audio is playing
This patch adds the paramater auto_shutdown_output to the kernel module.
Default behaviour of the module is the same, but when auto_shutdown_output
is set to 1, the SPDIF oputput will shutdown if no stream is playing.
bugfix for 32kHz sample rate, was missing
HiFiBerry Digi: set SPDIF status bits for sample rate
The HiFiBerry Digi driver did not signal the sample rate in the SPDIF status bits.
While this is optional, some DACs and receivers do not accept this signal. This patch
adds the sample rate bits in the SPDIF status block.
This adds a machine driver for the HifiBerry DAC.
It is a sound card that can
be stacked onto the Raspberry Pi.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
1-wire: Add support for configuring pin for w1-gpio kernel module
See: https://github.com/raspberrypi/linux/pull/457
Add bitbanging pullups, use them for w1-gpio
Allows parasite power to work, uses module option pullup=1
bcm2708: Ensure 1-wire pullup is disabled by default, and expose as module parameter
Signed-off-by: Alex J Lennon <ajlennon@dynamicdevices.co.uk>
w1-gpio: Add gpiopin module parameter and correctly free up gpio pull-up pin, if set
Signed-off-by: Alex J Lennon <ajlennon@dynamicdevices.co.uk>
w1-gpio: Sort out the pullup/parasitic power tangle
Especially on platforms with a slower CPU but a relatively high
framebuffer fill bandwidth, like current ARM devices, the existing
console monochrome imageblit function used to draw console text is
suboptimal for common pixel depths such as 16bpp and 32bpp. The existing
code is quite general and can deal with several pixel depths. By creating
special case functions for 16bpp and 32bpp, by far the most common pixel
formats used on modern systems, a significant speed-up is attained
which can be readily felt on ARM-based devices like the Raspberry Pi
and the Allwinner platform, but should help any platform using the
fb layer.
The special case functions allow constant folding, eliminating a number
of instructions including divide operations, and allow the use of an
unrolled loop, eliminating instructions with a variable shift size,
reducing source memory access instructions, and eliminating excessive
branching. These unrolled loops also allow much better code optimization
by the C compiler. The code that selects which optimized variant is used
is also simplified, eliminating integer divide instructions.
The speed-up, measured by timing 'cat file.txt' in the console, varies
between 40% and 70%, when testing on the Raspberry Pi and Allwinner
ARM-based platforms, depending on font size and the pixel depth, with
the greater benefit for 32bpp.
Signed-off-by: Harm Hanemaaijer <fgenfb@yahoo.com>
Based on the patch authored by Ali Gholami Rudi at
https://lkml.org/lkml/2009/7/13/153
Provide an ioctl for userspace applications, but only if this operation
is hardware accelerated (otherwide it does not make any sense).
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
The "input" trigger makes the associated GPIO an input. This is to support
the Raspberry Pi PWR LED, which is driven by external hardware in normal use.
N.B. pwr_led is not available on Model A or B boards.
leds-gpio: Implement the brightness_get method
The power LED uses some clever logic that means it is driven
by a voltage measuring circuit when configured as input, otherwise
it is driven by the GPIO output value. This patch wires up the
brightness_get method for leds-gpio so that user-space can monitor
the LED value via /sys/class/gpio/led1/brightness. Using the input
trigger this returns an indication of the system power health,
otherwise it is just whatever value the trigger has written most
recently.
See: https://github.com/raspberrypi/linux/issues/1064
The EPAPR standard says to use "phandle" properties to store phandles,
rather than the deprecated "linux,phandle" version. By default, dtc
generates both, but adding "-H epapr" causes it to only generate
"phandle"s, saving some space and clutter.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Change the filenames and extensions to keep the pre-DDT style of
overlay (<name>-overlay.dtb) distinct from new ones that use a
different style of local fixups (<name>.dtbo), and to match other
platforms.
The RPi firmware uses the DDTK trailer atom to choose which type of
overlay to use for each kernel.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Add the bare minimum needed to boot BCM2708 from a Device Tree.
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
BCM2708: DT: change 'axi' nodename to 'soc'
Change DT node named 'axi' to 'soc' so it matches ARCH_BCM2835.
The VC4 bootloader fills in certain properties in the 'axi' subtree,
but since this is part of an upstreaming effort, the name is changed.
Signed-off-by: Noralf Tronnes notro@tronnes.org
BCM2708_DT: Correct length of the peripheral space
Use dts-dirs feature for overlays.
The kernel makefiles have a dts-dirs target that is for vendor subdirectories.
Using this fixes the install_dtbs target, which previously did not install the overlays.
BCM270X_DT: configure I2S DMA channels
Signed-off-by: Matthias Reichl <hias@horus.com>
BCM270X_DT: switch to bcm2835-i2s
I2S soundcard drivers with proper devicetree support (i.e. not linking
to the cpu_dai/platform via name but to cpu/platform via of_node)
will work out of the box without any modifications.
When the kernel is compiled without devicetree support the platform
code will instantiate the bcm2708-i2s driver and I2S soundcard drivers
will link to it via name, as before.
Signed-off-by: Matthias Reichl <hias@horus.com>
SDIO-overlay: add poll_once-boolean parameter
Add paramter to toggle sdio-device-polling
done every second or once at boot-time.
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
BCM270X_DT: Make mmc overlay compatible with current firmware
The original DT overlay logic followed a merge-then-patch procedure,
i.e. parameters are applied to the loaded overlay before the overlay
is merged into the base DTB. This sequence has been changed to
patch-then-merge, in order to support parameterised node names, and
to protect against bad overlays. As a result, overrides (parameters)
must only target labels in the overlay, but the overlay can obviously target nodes in the base DTB.
mmc-overlay.dts (that switches back to the original mmc sdcard
driver) is the only overlay violating that rule, and this patch
fixes it.
bcm270x_dt: Use the sdhost MMC controller by default
The "mmc" overlay reverts to using the other controller.
squash: Add cprman to dt
BCM270X_DT: Use clk_core for I2C interfaces
Includes the new localfixups format.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
scripts/dtc: Fix UMR causing corrupt dtbo overlay files
struct fixup_entry is allocated from the heap but it's member
local_fixup_generated was never initialized. This lead to
corrupted dtbo files.
Fix this by initializing local_fixup_generated to false.
Signed-off-by: Matthias Reichl <hias@horus.com>
scripts/dtc: Only emit local fixups for overlays
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The Raspberry Pi firmware looks for a trailer on the kernel image to
determine whether it was compiled with Device Tree support enabled.
If the firmware finds a kernel without this trailer, or which has a
trailer indicating that it isn't DT-capable, it disables DT support
and reverts to using ATAGs.
The mkknlimg utility adds that trailer, having first analysed the
image to look for signs of DT support and the kernel version string.
knlinfo displays the contents of the trailer in the given kernel image.
scripts/mkknlimg: Add support for ARCH_BCM2835
Add a new trailer field indicating whether this is an ARCH_BCM2835
build, as opposed to MACH_BCM2708/9. If the loader finds this flag
is set it changes the default base dtb file name from bcm270x...
to bcm283y...
Also update knlinfo to show the status of the field.
scripts/mkknlimg: Improve ARCH_BCM2835 detection
The board support code contains sufficient strings to be able to
distinguish 2708 vs. 2835 builds, so remove the check for
bcm2835-pm-wdt which could exist in either.
Also, since the canned configuration is no longer built in (it's
a module), remove the config string checking.
See: https://github.com/raspberrypi/linux/issues/1157
scripts: Multi-platform support for mkknlimg and knlinfo
The firmware uses tags in the kernel trailer to choose which dtb file
to load. Current firmware loads bcm2835-*.dtb if the '283x' tag is true,
otherwise it loads bcm270*.dtb. This scheme breaks if an image supports
multiple platforms.
This patch adds '270X' and '283X' tags to indicate support for RPi and
upstream platforms, respectively. '283x' (note lower case 'x') is left
for old firmware, and is only set if the image only supports upstream
builds.
scripts/mkknlimg: Append a trailer for all input
Now that the firmware assumes an unsigned kernel is DT-capable, it is
helpful to be able to mark a kernel as being non-DT-capable.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
scripts/knlinfo: Decode DDTK atom
Show the DDTK atom as being a boolean.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
- Supports raw YUV capture, preview, JPEG and H264.
- Uses videobuf2 for data transfer, using dma_buf.
- Uses 3.6.10 timestamping
- Camera power based on use
- Uses immutable input mode on video encoder
Signed-off-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Luke Diamand <luked@broadcom.com>
V4L2: Fixes from 6by9
V4L2: Fix EV values. Add manual shutter speed control
V4L2 EV values should be in units of 1/1000. Corrected.
Add support for V4L2_CID_EXPOSURE_ABSOLUTE which should
give manual shutter control. Requires manual exposure mode
to be selected first.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Correct JPEG Q-factor range
Should be 1-100, not 0-100
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Fix issue of driver jamming if STREAMON failed.
Fix issue where the driver was left in a partially enabled
state if STREAMON failed, and would then reject many IOCTLs
as it thought it was streaming.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Fix ISO controls.
Driver was passing the index to the GPU, and not the desired
ISO value.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Add flicker avoidance controls
Add support for V4L2_CID_POWER_LINE_FREQUENCY to set flicker
avoidance frequencies.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Add support for frame rate control.
Add support for frame rate (or time per frame as V4L2
inverts it) control via s_parm.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Improve G_FBUF handling so we pass conformance
Return some sane numbers for get framebuffer so that
we pass conformance.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Fix information advertised through g_vidfmt
Width and height were being stored based on incorrect
values.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Add support for inline H264 headers
Add support for V4L2_CID_MPEG_VIDEO_REPEAT_SEQ_HEADER
to control H264 inline headers.
Requires firmware fix to work correctly, otherwise format
has to be set to H264 before this parameter is set.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Fix JPEG timestamp issue
JPEG images were coming through from the GPU with timestamp
of 0. Detect this and give current system time instead
of some invalid value.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Fix issue when switching down JPEG resolution.
JPEG buffer size calculation is based on input resolution.
Input resolution was being configured after output port
format. Caused failures if switching from one JPEG resolution
to a smaller one.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Enable MJPEG encoding
Requires GPU firmware update to support MJPEG encoder.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Correct flag settings for compressed formats
Set flags field correctly on enum_fmt_vid_cap for compressed
image formats.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: H264 profile & level ctrls, FPS control and auto exp pri
Several control handling updates.
H264 profile and level controls.
Timeperframe/FPS reworked to add V4L2_CID_EXPOSURE_AUTO_PRIORITY to
select whether AE is allowed to override the framerate specified.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Correct BGR24 to RGB24 in format table
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Add additional pixel formats. Correct colourspace
Adds the other flavours of YUYV, and NV12.
Corrects the overlay advertised colourspace.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Drop logging msg from info to debug
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Initial pass at scene modes.
Only supports exposure mode and metering modes.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Add manual white balance control.
Adds support for V4L2_CID_RED_BALANCE and
V4L2_CID_BLUE_BALANCE. Only has an effect if
V4L2_CID_AUTO_N_PRESET_WHITE_BALANCE has
V4L2_WHITE_BALANCE_MANUAL selected.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
config: Enable V4L / MMAL driver
V4L2: Increase the MMAL timeout to 3sec
MJPEG codec flush is now taking longer and results
in a kernel panic if the driver has stopped waiting for
the result when it finally completes.
Increase the timeout value from 1 to 3secs.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Add support for setting H264_I_PERIOD
Adds support for the parameter V4L2_CID_MPEG_VIDEO_H264_I_PERIOD
to set the frequency with which I frames are produced.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Enable GPU function for removing padding from images.
GPU can now support arbitrary strides, although may require
additional processing to achieve it. Enable this feature
so that the images delivered are the size requested.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Add support for V4L2_PIX_FMT_BGR32
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Set the colourspace to avoid odd YUV-RGB conversions
Removes the amiguity from the conversion routines and stops
them dropping back to the SD vs HD choice of coeffs.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Make video/still threshold a run-time param
Move the define for at what resolution the driver
switches from a video mode capture to a stills mode
capture to module parameters.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Fix incorrect pool sizing
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Add option to disable enum_framesizes.
Gstreamer's handling of a driver that advertises
V4L2_FRMSIZE_TYPE_STEPWISE to define the supported
resolutions is broken. See bug
https://bugzilla.gnome.org/show_bug.cgi?id=726521
Optional parameter of gst_v4l2src_is_broken added.
If non-zero, the driver claims not to support that
ioctl, and gstreamer should be happy again (it
guesses a set of defaults for itself).
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Add support for more image formats
Adds YVU420 (YV12), YVU420SP (NV21), and BGR888.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Extend range for V4L2_CID_MPEG_VIDEO_H264_I_PERIOD
Request to extend the range from the fairly arbitrary
1000 frames (33 seconds at 30fps). Extend out to the
max range supported (int32 value).
Also allow 0, which is handled by the codec as only
send an I-frame on the first frame and never again.
There may be an exception if it detects a significant
scene change, but there's no easy way around that.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
bcm2835-camera: stop_streaming now has a void return
BCM2835-V4L2: Fix compliance test failures
VIDIOC_TRY_FMT and VIDIOC_S_FMT tests were faling due
to reporting V4L2_COLORSPACE_JPEG when the colour
format wasn't V4L2_PIX_FMT_JPEG.
Now reports V4L2_COLORSPACE_SMPTE170M for YUV formats.
bcm2835 camera planar/packed stride length
Added a field to the mmal_fmt struct used to compute the bytes per line
when using a particular format. This results in the correct stride being
calculated even when the format is planar.
Signed-off-by: Garrett Wilson <g@floft.net>
bcm2835: camera: check for scene not being found
static analysis by cppcheck detected some potential NULL pointer
dereference issues:
[drivers/media/platform/bcm2835/controls.c:854]: (error) Possible null
pointer dereference: scene
(and lines 858, 859 too)
it is possible that scene is not found because of an invalue ctrl->val
and is therefore NULL and hence causing a null pointer dereference.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
bcm2835: memcpy port data to m rather than rmsg
static analysis by cppcheck detected a memcpy to rmsg which is
not actually initialized at that point. The memcpy should be copying
to variable m instead.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
BCM2835-V4L2: Return buffers to videobuf2 on shutdown
https://github.com/raspberrypi/linux/issues/817
Fixes the kernel warning from videobuf2 as buffers
are now returned as they are being flushed on
stop_streaming.
squash: Fixup bcm2835-camera for changes in kernel 4.4 api
v4l2: Fix up driver to upstream timestamp changes
bcm2835-camera: fix a bug in computation of frame timestamp
Fixes#1318
V4L2 driver updates (#1393)
* BCM2835-V4L2: Correct ISO control and add V4L2_CID_ISO_SENSITIVITY_AUTO
https://github.com/raspberrypi/linux/issues/1251
V4L2_CID_ISO_SENSITIVITY was not advertising ISO*1000 as it should.
V4L2_CID_ISO_SENSITIVITY_AUTO was not implemented, so was taking
V4L2_CID_ISO_SENSITIVITY as 0 for auto mode.
Still accepts 0 for auto, but also abides by the new parameter.
Signed-off-by: Dave Stevenson <6by9@users.noreply.github.com>
* BCM2835-V4L2: Add a video_nr parameter.
Adds a kernel parameter "video_nr" to specify the preferred
/dev/videoX device node.
https://www.raspberrypi.org/forums/viewtopic.php?f=38&t=136120&p=905545
Signed-off-by: Dave Stevenson <6by9@users.noreply.github.com>
* BCM2835-V4L2: Add support for multiple cameras
Ask GPU on load how many cameras have been detected, and
enumerate that number of devices.
Only applicable on the Compute Module as no other device
exposes multiple CSI2 interfaces.
Signed-off-by: Dave Stevenson <6by9@users.noreply.github.com>
* BCM2835-V4L2: Add control of the overlay location and alpha.
Actually do something useful in vidioc_s_fmt_vid_overlay and
vidioc_try_fmt_vid_overlay, rather than effectively having
read-only fields.
Signed-off-by: Dave Stevenson <6by9@users.noreply.github.com>
* BCM2835-V4L2: V4L2-Compliance failure fix
VIDIOC_TRY_FMT was failing due to bytesperline not
being set correctly by default.
Signed-off-by: Dave Stevenson <6by9@users.noreply.github.com>
* BCM2835-V4L2: Make all module parameters static
Clean up to correct variable scope
Signed-off-by: Dave Stevenson <6by9@users.noreply.github.com>
V4L2: Request maximum resolution from GPU
Get resolution information about the sensors from the GPU
and advertise it correctly.
Signed-off-by: Dave Stevenson <6by9@users.noreply.github.com>
BCM2835-V4L2: Increase minimum resolution to 32x32
https://github.com/raspberrypi/linux/issues/1498 showed
up that 16x16 is failing to work on the GPU for some reason.
GPU bug being tracked on
https://github.com/raspberrypi/firmware/issues/607
Workaround here by increasing minimum resolution via V4L2
to 32x32.
Signed-off-by: Dave Stevenson <6by9@users.noreply.github.com>
[media]: bcm2835-camera: fix compilation error
There is an error when compiling rpi-4.6.y branch:
CC [M] drivers/media/platform/bcm2835/bcm2835-camera.o
drivers/media/platform/bcm2835/bcm2835-camera.c:639:17: error: initialization from incompatible pointer type [-Werror=incompatible-pointer-types]
.queue_setup = queue_setup,
^
drivers/media/platform/bcm2835/bcm2835-camera.c:639:17: note: (near initialization for 'bm2835_mmal_video_qops.queue_setup')
The const void *parg in setup_queue callback is not needed since commit:
df9ecb0cad.
This commit removes it.
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
bcm2835-camera: Fix max/min error when looping over cameras/resolutions
See: https://github.com/raspberrypi/linux/issues/1447#issuecomment-221303506
Support booting without Device Tree.
Turn on USB power.
Load driver early because of lacking support for deferred probing
in many drivers.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Add module for accessing the mailbox property channel through
/dev/vcio. Was previously in bcm2708-vcio.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
i2c-bcm2708: fixed baudrate
Fixed issue where the wrong CDIV value was set for baudrates below 3815 Hz (for 250MHz bus clock).
In that case the computed CDIV value was more than 0xffff. However the CDIV register width is only 16 bits.
This resulted in incorrect setting of CDIV and higher baudrate than intended.
Example: 3500Hz -> CDIV=0x11704 -> CDIV(16bit)=0x1704 -> 42430Hz
After correction: 3500Hz -> CDIV=0x11704 -> CDIV(16bit)=0xffff -> 3815Hz
The correct baudrate is shown in the log after the cdiv > 0xffff correction.
Perform I2C combined transactions when possible
Perform I2C combined transactions whenever possible, within the
restrictions of the Broadcomm Serial Controller.
Disable DONE interrupt during TA poll
Prevent interrupt from being triggered if poll is missed and transfer
starts and finishes.
i2c: Make combined transactions optional and disabled by default
i2c: bcm2708: add device tree support
Add DT support to driver and add to .dtsi file.
Setup pins in .dts file.
i2c is disabled by default.
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
bcm2708: don't register i2c controllers when using DT
The devices for the i2c controllers are in the Device Tree.
Only register devices when not using DT.
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
I2C: Only register the I2C device for the current board revision
i2c_bcm2708: Fix clock reference counting
Fix grabbing lock from atomic context in i2c driver
2 main changes:
- check for timeouts in the bcm2708_bsc_setup function as indicated by this comment:
/* poll for transfer start bit (should only take 1-20 polls) */
This implies that the setup function can now fail so account for this everywhere it's called
- Removed the clk_get_rate call from inside the setup function as it locks a mutex and that's not ok since we call it from under a spin lock.
i2c-bcm2708: When using DT, leave the GPIO setup to pinctrl
i2c-bcm2708: Increase timeouts to allow larger transfers
Use the timeout value provided by the I2C_TIMEOUT ioctl when waiting
for completion. The default timeout is 1 second.
See: https://github.com/raspberrypi/linux/issues/260
i2c-bcm2708/BCM270X_DT: Add support for I2C2
The third I2C bus (I2C2) is normally reserved for HDMI use. Careless
use of this bus can break an attached display - use with caution.
It is recommended to disable accesses by VideoCore by setting
hdmi_ignore_edid=1 or hdmi_edid_file=1 in config.txt.
The interface is disabled by default - enable using the
i2c2_iknowwhatimdoing DT parameter.
bcm2708-spi: Don't use static pin configuration with DT
Also remove superfluous error checking - the SPI framework ensures the
validity of the chip_select value.
i2c-bcm2708: Remove non-DT support
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Set the BSC_CLKT clock streching timeout to 35ms as per SMBus specs.
BCM270x: Move thermal sensor to Device Tree
Add Device Tree support to bcm2835-thermal driver.
Add thermal sensor device to Device Tree.
Don't add platform device when booting in DT mode.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
lirc_rpi: Use read_current_timer to determine transmitter delay. Thanks to jjmz and others
See: https://github.com/raspberrypi/linux/issues/525
lirc: Remove restriction on gpio pins that can be used with lirc
Compute Module, for example could use different pins
lirc_rpi: Add parameter to specify input pin pull
Depending on the connected IR circuitry it might be desirable to change the
gpios internal pull from it pull-down default behaviour. Add a module
parameter to allow the user to set it explicitly.
Signed-off-by: Julian Scheel <julian@jusst.de>
lirc-rpi: Use the higher-level irq control functions
This module used to access the irq_chip methods of the
gpio controller directly, rather than going through the
standard enable_irq/irq_set_irq_type functions. This
caused problems on pinctrl-bcm2835 which only implements
the irq_enable/disable methods and not irq_unmask/mask.
lirc-rpi: Correct the interrupt usage
1) Correct the use of enable_irq (i.e. don't call it so often)
2) Correct the shutdown sequence.
3) Avoid a bcm2708_gpio driver quirk by setting the irq flags earlier
lirc-rpi: use getnstimeofday instead of read_current_timer
read_current_timer isn't guaranteed to return values in
microseconds, and indeed it doesn't on a Pi2.
Issue: linux#827
lirc-rpi: Add device tree support, and a suitable overlay
The overlay supports DT parameters that match the old module
parameters, except that gpio_in_pull should be set using the
strings "up", "down" or "off".
lirc-rpi: Also support pinctrl-bcm2835 in non-DT mode
Add experimental support for the VideoCore shared memory service.
This allows user processes to allocate memory from VideoCore's
GPU relocatable heap and mmap the buffers. Additionally, the memory
handles can passed to other VideoCore services such as MMAL, OpenMax
and DispmanX
TODO
* This driver was originally released for BCM28155 which has a different
cache architecture to BCM2835. Consequently, in this release only
uncached mappings are supported. However, there's no fundamental
reason which cached mappings cannot be support or BCM2835
* More refactoring is required to remove the typedefs.
* Re-enable the some of the commented out debug-fs statistics which were
disabled when migrating code from proc-fs.
* There's a lot of code to support sharing of VCSM in order to support
Android. This could probably done more cleanly or perhaps just
removed.
Signed-off-by: Tim Gover <timgover@gmail.com>
config: Disable VC_SM for now to fix hang with cutdown kernel
vcsm: Use boolean as it cannot be built as module
On building the bcm_vc_sm as a module we get the following error:
v7_dma_flush_range and do_munmap are undefined in vc-sm.ko.
Fix by making it not an option to build as module
vcsm: Add ioctl for custom cache flushing
vc-sm: Move headers out of arch directory
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: popcornmix <popcornmix@gmail.com>
BCM270x: Move vc_mem
Make the vc_mem module available for ARCH_BCM2835 by moving it.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: popcornmix <popcornmix@gmail.com>
vchiq: create_pagelist copes with vmalloc memory
Signed-off-by: Daniel Stone <daniels@collabora.com>
vchiq: fix the shim message release
Signed-off-by: Daniel Stone <daniels@collabora.com>
vchiq: export additional symbols
Signed-off-by: Daniel Stone <daniels@collabora.com>
VCHIQ: Make service closure fully synchronous (drv)
This is one half of a two-part patch, the other half of which is to
the vchiq_lib user library. With these patches, calls to
vchiq_close_service and vchiq_remove_service won't return until any
associated callbacks have been delivered to the callback thread.
VCHIQ: Add per-service tracing
The new service option VCHIQ_SERVICE_OPTION_TRACE is a boolean that
toggles tracing for the specified service.
This commit also introduces vchi_service_set_option and the associated
option VCHI_SERVICE_OPTION_TRACE.
vchiq: Make the synchronous-CLOSE logic more tolerant
vchiq: Move logging control into debugfs
vchiq: Take care of a corner case tickled by VCSM
Closing a connection that isn't fully open requires care, since one
side does not know the other side's port number. Code was present to
handle the case where a CLOSE is sent immediately after an OPEN, i.e.
before the OPENACK has been received, but this was incorrectly being
used when an OPEN from a client using port 0 was rejected.
(In the observed failure, the host was attempting to use the VCSM
service, which isn't present in the 'cutdown' firmware. The failure
was intermittent because sometimes the keepalive service would
grab port 0.)
This case can be distinguished because the client's remoteport will
still be VCHIQ_PORT_FREE, and the srvstate will be OPENING. Either
condition is sufficient to differentiate it from the special case
described above.
vchiq: Avoid high load when blocked and unkillable
vchiq: Include SIGSTOP and SIGCONT in list of signals not-masked by vchiq to allow gdb to work
vchiq_arm: Complete support for SYNCHRONOUS mode
vchiq: Remove inline from suspend/resume
vchiq: Allocation does not need to be atomic
vchiq: Fix wrong condition check
The log level is checked from within the log call. Remove the check in the call.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
BCM270x: Add vchiq device to platform file and Device Tree
Prepare to turn the vchiq module into a driver.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2708: vchiq: Add Device Tree support
Turn vchiq into a driver and stop hardcoding resources.
Use devm_* functions in probe path to simplify cleanup.
A global variable is used to hold the register address. This is done
to keep this patch as small as possible.
Also make available on ARCH_BCM2835.
Based on work by Lubomir Rintel.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
vchiq: Change logging level for inbound data
vchiq_arm: Two cacheing fixes
1) Make fragment size vary with cache line size
Without this patch, non-cache-line-aligned transfers may corrupt
(or be corrupted by) adjacent data structures.
Both ARM and VC need to be updated to enable this feature. This is
ensured by having the loader apply a new DT parameter -
cache-line-size. The existence of this parameter guarantees that the
kernel is capable, and the parameter will only be modified from the
safe default if the loader is capable.
2) Flush/invalidate vmalloc'd memory, and invalidate after reads
vchiq: fix NULL pointer dereference when closing driver
The following code run as root will cause a null pointer dereference oops:
int fd = open("/dev/vc-cma", O_RDONLY);
if (fd < 0)
err(1, "open failed");
(void)close(fd);
[ 1704.877721] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[ 1704.877725] pgd = b899c000
[ 1704.877736] [00000000] *pgd=37fab831, *pte=00000000, *ppte=00000000
[ 1704.877748] Internal error: Oops: 817 [#1] PREEMPT SMP ARM
[ 1704.877765] Modules linked in: evdev i2c_bcm2708 uio_pdrv_genirq uio
[ 1704.877774] CPU: 2 PID: 3656 Comm: stress-ng-fstat Not tainted 3.19.1-12-generic-bcm2709 #12-Ubuntu
[ 1704.877777] Hardware name: BCM2709
[ 1704.877783] task: b8ab9b00 ti: b7e68000 task.ti: b7e68000
[ 1704.877798] PC is at __down_interruptible+0x50/0xec
[ 1704.877806] LR is at down_interruptible+0x5c/0x68
[ 1704.877813] pc : [<80630ee8>] lr : [<800704b0>] psr: 60080093
sp : b7e69e50 ip : b7e69e88 fp : b7e69e84
[ 1704.877817] r10: b88123c8 r9 : 00000010 r8 : 00000001
[ 1704.877822] r7 : b8ab9b00 r6 : 7fffffff r5 : 80a1cc34 r4 : 80a1cc34
[ 1704.877826] r3 : b7e69e50 r2 : 00000000 r1 : 00000000 r0 : 80a1cc34
[ 1704.877833] Flags: nZCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment user
[ 1704.877838] Control: 10c5387d Table: 3899c06a DAC: 00000015
[ 1704.877843] Process do-oops (pid: 3656, stack limit = 0xb7e68238)
[ 1704.877848] Stack: (0xb7e69e50 to 0xb7e6a000)
[ 1704.877856] 9e40: 80a1cc3c 00000000 00000010 b88123c8
[ 1704.877865] 9e60: b7e69e84 80a1cc34 fff9fee9 ffffffff b7e68000 00000009 b7e69ea4 b7e69e88
[ 1704.877874] 9e80: 800704b0 80630ea4 fff9fee9 60080013 80a1cc28 fff9fee9 b7e69edc b7e69ea8
[ 1704.877884] 9ea0: 8040f558 80070460 fff9fee9 ffffffff 00000000 00000000 00000009 80a1cb7c
[ 1704.877893] 9ec0: 00000000 80a1cb7c 00000000 00000010 b7e69ef4 b7e69ee0 803e1ba4 8040f514
[ 1704.877902] 9ee0: 00000e48 80a1cb7c b7e69f14 b7e69ef8 803e1c9c 803e1b74 b88123c0 b92acb18
[ 1704.877911] 9f00: b8812790 b8d815d8 b7e69f24 b7e69f18 803e2250 803e1bc8 b7e69f5c b7e69f28
[ 1704.877921] 9f20: 80167bac 803e222c 00000000 00000000 b7e69f54 b8ab9ffc 00000000 8098c794
[ 1704.877930] 9f40: b8ab9b00 8000efc4 b7e68000 00000000 b7e69f6c b7e69f60 80167d6c 80167b28
[ 1704.877939] 9f60: b7e69f8c b7e69f70 80047d38 80167d60 b7e68000 b7e68010 8000efc4 b7e69fb0
[ 1704.877949] 9f80: b7e69fac b7e69f90 80012820 80047c84 01155490 011549a8 00000001 00000006
[ 1704.877957] 9fa0: 00000000 b7e69fb0 8000ee5c 80012790 00000000 353d8c0f 7efc4308 00000000
[ 1704.877966] 9fc0: 01155490 011549a8 00000001 00000006 00000000 00000000 76cf3ba0 00000003
[ 1704.877975] 9fe0: 00000000 7efc42e4 0002272f 76e2ed66 60080030 00000003 00000000 00000000
[ 1704.877998] [<80630ee8>] (__down_interruptible) from [<800704b0>] (down_interruptible+0x5c/0x68)
[ 1704.878015] [<800704b0>] (down_interruptible) from [<8040f558>] (vchiu_queue_push+0x50/0xd8)
[ 1704.878032] [<8040f558>] (vchiu_queue_push) from [<803e1ba4>] (send_worker_msg+0x3c/0x54)
[ 1704.878045] [<803e1ba4>] (send_worker_msg) from [<803e1c9c>] (vc_cma_set_reserve+0xe0/0x1c4)
[ 1704.878057] [<803e1c9c>] (vc_cma_set_reserve) from [<803e2250>] (vc_cma_release+0x30/0x38)
[ 1704.878069] [<803e2250>] (vc_cma_release) from [<80167bac>] (__fput+0x90/0x1e0)
[ 1704.878082] [<80167bac>] (__fput) from [<80167d6c>] (____fput+0x18/0x1c)
[ 1704.878094] [<80167d6c>] (____fput) from [<80047d38>] (task_work_run+0xc0/0xf8)
[ 1704.878109] [<80047d38>] (task_work_run) from [<80012820>] (do_work_pending+0x9c/0xc4)
[ 1704.878123] [<80012820>] (do_work_pending) from [<8000ee5c>] (work_pending+0xc/0x20)
[ 1704.878133] Code: e50b1034 e3a01000 e50b2030 e580300c (e5823000)
..the fix is to ensure that we have actually initialized the queue before we attempt
to push any items onto it. This occurs if we do an open() followed by a close() without
any activity in between.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
vchiq_arm: Sort out the vmalloc case
See: https://github.com/raspberrypi/linux/issues/1055
vchiq: hack: Add include depecated dma include file
vchiq_arm: Tweak the logging output
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
vchiq_arm: Access the dequeue_pending flag locked
Reading through this code looking for another problem (now found in userland)
the use of dequeue_pending outside a lock didn't seem safe.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
vchiq_arm: Service callbacks must not fail
Service callbacks are not allowed to return an error. The internal callback
that delivers events and messages to user tasks does not enqueue them if
the service is closing, but this is not an error and should not be
reported as such.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
vchiq_arm: do not use page_cache_release(page) macro (#1403)
This macro is gone since 1fa64f198b.
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
vchiq: Upate to match get_user_pages prototype
vchiq_arm: Add completion records under the mutex
An issue was observed when flushing openmax components
which generate a large number of messages returning
buffers to host.
We occasionally found a duplicate message from 16
messages prior, resulting in a buffer returned twice.
While only one thread adds completions, without the
mutex you don't get the protection of the automatic
memory barrier you get with synchronisation objects.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: popcornmix <popcornmix@gmail.com>
alsa: add mmap support and some cleanups to bcm2835 ALSA driver
snd-bcm2835: Add support for spdif/hdmi passthrough
This adds a dedicated subdevice which can be used for passthrough of non-audio
formats (ie encoded a52) through the hdmi audio link. In addition to this
driver extension an appropriate card config is required to make alsa-lib
support the AES parameters for this device.
snd-bcm2708: Add mutex, improve logging
Fix for ALSA driver crash
Avoids an issue when closing and opening vchiq where a message can arrive before service handle has been written
alsa: reduce severity of expected warning message
snd-bcm2708: Fix dmesg spam for non-error case
alsa: Ensure mutexes are released through error paths
alsa: Make interrupted close paths quieter
BCM270x: Add onboard sound device to Device Tree
Add Device Tree support to alsa driver.
Add device to Device Tree.
Don't add platform devices when booting in DT mode.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2835: access controls under the audio mutex
I don't think the ALSA framework provides any kind of automatic
synchronization within the control callbacks. We most likely need
to ensure this manually, so add locking around all access to shared
mutable data. In particular, bcm2835_audio_set_ctls() should
probably always be called under our own audio lock.
Signed-off-by: popcornmix <popcornmix@gmail.com>
vc_cma: Make the vc_cma area the default contiguous DMA area
vc_cma: Provide empty functions when module is not built
Providing empty functions saves the users from guarding the
function call with an #if clause.
Move __init markings from prototypes to functions.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Some SD cards have been found that corrupt data when small blocks
are erased. Add a quirk to indicate that ERASE should not be used,
and set it for cards of that type.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
mmc: Apply QUIRK_BROKEN_ERASE to other capacities
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
mmc: Add card_quirks module parameter, log quirks
Use mmc_block.card_quirks to override the quirks for all SD or MMC
cards. The value is a bitfield using the bit positions defined in
include/linux/mmc/card.h. If the module parameter is placed in the
kernel command line (or bootargs) stored on the card then, assuming the
device only has one SD card interface, the override effectively becomes
card-specific.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM2835 has two SD card interfaces. This driver uses the other one.
bcm2835-sdhost: Error handling fix, and code clarification
bcm2835-sdhost: Adding overclocking option
Allow a different clock speed to be substitued for a requested 50MHz.
This option is exposed using the "overclock_50" DT parameter.
Note that the sdhost interface is restricted to integer divisions of
core_freq, and the highest sensible option for a core_freq of 250MHz
is 84 (250/3 = 83.3MHz), the next being 125 (250/2) which is much too
high.
Use at your own risk.
bcm2835-sdhost: Round up the overclock, so 62 works for 62.5Mhz
Also only warn once for each overclock setting.
bcm2835-sdhost: Improve error handling and recovery
1) Expose the hw_reset method to the MMC framework, removing many
internal calls by the driver.
2) Reduce overclock setting on error.
3) Increase timeout to cope with high capacity cards.
4) Add properties and parameters to control pio_limit and debug.
5) Reduce messages at probe time.
bcm2835-sdhost: Further improve overclock back-off
bcm2835-sdhost: Clear HBLC for PIO mode
Also update pio_limit default in overlay README.
bcm2835-sdhost: Add the ERASE capability
See: https://github.com/raspberrypi/linux/issues/1076
bcm2835-sdhost: Ignore CRC7 for MMC CMD1
It seems that the sdhost interface returns CRC7 errors for CMD1,
which is the MMC-specific SEND_OP_COND. Returning these errors to
the MMC layer causes a downward spiral, but ignoring them seems
to be harmless.
bcm2835-mmc/sdhost: Remove ARCH_BCM2835 differences
The bcm2835-mmc driver (and -sdhost driver that copied from it)
contains code to handle SDIO interrupts in a threaded interrupt
handler rather than waking the MMC framework thread. The change
follows a patch from Russell King that adds the facility as the
preferred way of working.
However, the new code path is only present in ARCH_BCM2835
builds, which I have taken to be a way of testing the waters
rather than making the change across the board; I can't see
any technical reason why it wouldn't be enabled for MACH_BCM270X
builds. So this patch standardises on the ARCH_BCM2835 code,
removing the old code paths.
bcm2835-sdhost: Don't log timeout errors unless debug=1
The MMC card-discovery process generates timeouts. This is
expected behaviour, so reporting it to the user serves no purpose.
Suppress the reporting of timeout errors unless the debug flag
is on.
bcm2835-sdhost: Add workaround for odd behaviour on some cards
For reasons not understood, the sdhost driver fails when reading
sectors very near the end of some SD cards. The problem could
be related to the similar issue that reading the final sector
of any card as part of a multiple read never completes, and the
workaround is an extension of the mechanism introduced to solve
that problem which ensures those sectors are always read singly.
bcm2835-sdhost: Major revision
This is a significant revision of the bcm2835-sdhost driver. It
improves on the original in a number of ways:
1) Through the use of CMD23 for reads it appears to avoid problems
reading some sectors on certain high speed cards.
2) Better atomicity to prevent crashes.
3) Higher performance.
4) Activity logging included, for easier diagnosis in the event
of a problem.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Restore ATOMIC flag to PIO sg mapping
Allocation problems have been seen in a wireless driver, and
this is the only change which might have been responsible.
SQUASH: bcm2835-sdhost: Only claim one DMA channel
With both MMC controllers enabled there are few DMA channels left. The
bcm2835-sdhost driver only uses DMA in one direction at a time, so it
doesn't need to claim two channels.
See: https://github.com/raspberrypi/linux/issues/1327
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Workaround for "slow" sectors
Some cards have been seen to cause timeouts after certain sectors are
read. This workaround enforces a minimum delay between the stop after
reading one of those sectors and a subsequent data command.
Using CMD23 (SET_BLOCK_COUNT) avoids this problem, so good cards will
not be penalised by this workaround.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Firmware manages the clock divisor
The bcm2835-sdhost driver hands control of the CDIV clock divisor
register to matching firmware, allowing it to adjust to a changing
core clock. This removes the need to use the performance governor or
to enable io_is_busy on the on-demand governor in order to get the
best SD performance.
N.B. As SD clocks must be an integer divisor of the core clock, it is
possible that the SD clock for "turbo" mode can be different (even
lower) than "normal" mode.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Reset the clock in task context
Since reprogramming the clock can now involve a round-trip to the
firmware it must not be done at atomic context, and a tasklet
is not a task.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
mmc: Disable CMD23 transfers on all cards
Pending wire-level investigation of these types of transfers
and associated errors on bcm2835-mmc, disable for now. Fallback of
CMD18/CMD25 transfers will be used automatically by the MMC layer.
Reported/Tested-by: Gellert Weisz <gellert@raspberrypi.org>
mmc: bcm2835-mmc: enable DT support for all architectures
Both ARCH_BCM2835 and ARCH_BCM270x are built with OF now.
Enable Device Tree support for all architectures.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
mmc: bcm2835-mmc: fix probe error handling
Probe error handling is broken in several places.
Simplify error handling by using device managed functions.
Replace pr_{err,info} with dev_{err,info}.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2835-mmc: Add locks when accessing sdhost registers
bcm2835-mmc: Add range of debug options for slowing things down
bcm2835-mmc: Add option to disable some delays
bcm2835-mmc: Add option to disable MMC_QUIRK_BLK_NO_CMD23
bcm2835-mmc: Default to disabling MMC_QUIRK_BLK_NO_CMD23
bcm2835-mmc: Adding overclocking option
Allow a different clock speed to be substitued for a requested 50MHz.
This option is exposed using the "overclock_50" DT parameter.
Note that the mmc interface is restricted to EVEN integer divisions of
250MHz, and the highest sensible option is 63 (250/4 = 62.5), the
next being 125 (250/2) which is much too high.
Use at your own risk.
bcm2835-mmc: Round up the overclock, so 62 works for 62.5Mhz
Also only warn once for each overclock setting.
mmc: bcm2835-mmc: Make available on ARCH_BCM2835
Make the bcm2835-mmc driver available for use on ARCH_BCM2835.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270x_DT: add bcm2835-mmc entry
Add Device Tree entry for bcm2835-mmc.
In non-DT mode, don't add the device in the board file.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2835-mmc: Don't overwrite MMC capabilities from DT
bcm2835-mmc: Don't override bus width capabilities from devicetree
Take out the force setting of the MMC_CAP_4_BIT_DATA host capability
so that the result read from devicetree via mmc_of_parse() is
preserved.
bcm2835-mmc: Only claim one DMA channel
With both MMC controllers enabled there are few DMA channels left. The
bcm2835-mmc driver only uses DMA in one direction at a time, so it
doesn't need to claim two channels.
See: https://github.com/raspberrypi/linux/issues/1327
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Add support for DMA controller of BCM2708 as used in the Raspberry Pi.
Currently it only supports cyclic DMA.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
dmaengine: expand functionality by supporting scatter/gather transfers sdhci-bcm2708 and dma.c: fix for LITE channels
DMA: fix cyclic LITE length overflow bug
dmaengine: bcm2708: Remove chancnt affectations
Mirror bcm2835-dma.c commit 9eba5536a7:
chancnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: overwrite dreq only if it is not set
dreq is set when the DMA channel is fetched from Device Tree.
slave_id is set using dmaengine_slave_config().
Only overwrite dreq with slave_id if it is not set.
dreq/slave_id in the cyclic DMA case is not touched, because I don't
have hardware to test with.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: do device registration in the board file
Don't register the device in the driver. Do it in the board file.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: don't restrict DT support to ARCH_BCM2835
Both ARCH_BCM2835 and ARCH_BCM270x are built with OF now.
Add Device Tree support to the non ARCH_BCM2835 case.
Use the same driver name regardless of architecture.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270x_DT: add bcm2835-dma entry
Add Device Tree entry for bcm2835-dma.
The entry doesn't contain any resources since they are handled
by the arch/arm/mach-bcm270x/dma.c driver.
In non-DT mode, don't add the device in the board file.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2708-dmaengine: Add debug options
BCM270x: Add memory and irq resources to dmaengine device and DT
Prepare for merging of the legacy DMA API arch driver dma.c
with bcm2708-dmaengine by adding memory and irq resources both
to platform file device and Device Tree node.
Don't use BCM_DMAMAN_DRIVER_NAME so we don't have to include mach/dma.h
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: Merge with arch dma.c driver and disable dma.c
Merge the legacy DMA API driver with bcm2708-dmaengine.
This is done so we can use bcm2708_fb on ARCH_BCM2835 (mailbox
driver is also needed).
Changes to the dma.c code:
- Use BIT() macro.
- Cutdown some comments to one line.
- Add mutex to vc_dmaman and use this, since the dev lock is locked
during probing of the engine part.
- Add global g_dmaman variable since drvdata is used by the engine part.
- Restructure for readability:
vc_dmaman_chan_alloc()
vc_dmaman_chan_free()
bcm_dma_chan_free()
- Restructure bcm_dma_chan_alloc() to simplify error handling.
- Use device irq resources instead of hardcoded bcm_dma_irqs table.
- Remove dev_dmaman_register() and code it directly.
- Remove dev_dmaman_deregister() and code it directly.
- Simplify bcm_dmaman_probe() using devm_* functions.
- Get dmachans from DT if available.
- Keep 'dma.dmachans' module argument name for backwards compatibility.
Make it available on ARCH_BCM2835 as well.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: set residue_granularity field
bcm2708-dmaengine supports residue reporting at burst level
but didn't report this via the residue_granularity field.
Without this field set properly we get playback issues with I2S cards.
dmaengine: bcm2708-dmaengine: Fix memory leak when stopping a running transfer
bcm2708-dmaengine: Use more DMA channels (but not 12)
1) Only the bcm2708_fb drivers uses the legacy DMA API, and
it requires a BULK-capable channel, so all other types
(FAST, NORMAL and LITE) can be made available to the regular
DMA API.
2) DMA channels 11-14 share an interrupt. The driver can't
handle this, so don't use channels 12-14 (12 was used, probably
because it appears to have an interrupt, but in reality that
interrupt is for activity on ANY channel). This may explain
a lockup encountered when running out of DMA channels.
The combined effect of this patch is to leave 7 DMA channels
available + channel 0 for bcm2708_fb via the legacy API.
See: https://github.com/raspberrypi/linux/issues/1110https://github.com/raspberrypi/linux/issues/1108
dmaengine: bcm2708: Make legacy API available for bcm2835-dma
bcm2708_fb uses the legacy DMA API, so in order to start using
bcm2835-dma, bcm2835-dma has to support the legacy API. Make this
possible by exporting bcm_dmaman_probe() and bcm_dmaman_remove().
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: Change DT compatible string
Both bcm2835-dma and bcm2708-dmaengine have the same compatible string.
So change compatible to "brcm,bcm2708-dma".
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: Remove driver but keep legacy API
Dropping non-DT support means we don't need this driver,
but we still need the legacy DMA API.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: popcornmix <popcornmix@gmail.com>
bcm2708_fb : Implement blanking support using the mailbox property interface
bcm2708_fb: Add pan and vsync controls
bcm2708_fb: DMA acceleration for fb_copyarea
Based on http://www.raspberrypi.org/phpBB3/viewtopic.php?p=62425#p62425
Also used Simon's dmaer_master module as a reference for tweaking DMA
settings for better performance.
For now busylooping only. IRQ support might be added later.
With non-overclocked Raspberry Pi, the performance is ~360 MB/s
for simple copy or ~260 MB/s for two-pass copy (used when dragging
windows to the right).
In the case of using DMA channel 0, the performance improves
to ~440 MB/s.
For comparison, VFP optimized CPU copy can only do ~114 MB/s in
the same conditions (hindered by reading uncached source buffer).
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
bcm2708_fb: report number of dma copies
Add a counter (exported via debugfs) reporting the
number of dma copies that the framebuffer driver
has done, in order to help evaluate different
optimization strategies.
Signed-off-by: Luke Diamand <luked@broadcom.com>
bcm2708_fb: use IRQ for DMA copies
The copyarea ioctl() uses DMA to speed things along. This
was busy-waiting for completion. This change supports using
an interrupt instead for larger transfers. For small
transfers, busy-waiting is still likely to be faster.
Signed-off-by: Luke Diamand <luke@diamand.org>
bcm2708: Make ioctl logging quieter
video: fbdev: bcm2708_fb: Don't panic on error
No need to panic the kernel if the video driver fails.
Just print a message and return an error.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
fbdev: bcm2708_fb: Add ARCH_BCM2835 support
Add Device Tree support.
Pass the device to dma_alloc_coherent() in order to get the
correct bus address on ARCH_BCM2835.
Use the new DMA legacy API header file.
Including <mach/platform.h> is not necessary.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270x_DT: Add bcm2708-fb device
Add bcm2708-fb to Device Tree and don't add the
platform device when booting in DT mode.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: popcornmix <popcornmix@gmail.com>
usb: dwc: fix lockdep false positive
Signed-off-by: Kari Suvanto <karis79@gmail.com>
usb: dwc: fix inconsistent lock state
Signed-off-by: Kari Suvanto <karis79@gmail.com>
Add FIQ patch to dwc_otg driver. Enable with dwc_otg.fiq_fix_enable=1. Should give about 10% more ARM performance.
Thanks to Gordon and Costas
Avoid dynamic memory allocation for channel lock in USB driver. Thanks ddv2005.
Add NAK holdoff scheme. Enabled by default, disable with dwc_otg.nak_holdoff_enable=0. Thanks gsh
Make sure we wait for the reset to finish
dwc_otg: fix bug in dwc_otg_hcd.c resulting in silent kernel
memory corruption, escalating to OOPS under high USB load.
dwc_otg: Fix unsafe access of QTD during URB enqueue
In dwc_otg_hcd_urb_enqueue during qtd creation, it was possible that the
transaction could complete almost immediately after the qtd was assigned
to a host channel during URB enqueue, which meant the qtd pointer was no
longer valid having been completed and removed. Usually, this resulted in
an OOPS during URB submission. By predetermining whether transactions
need to be queued or not, this unsafe pointer access is avoided.
This bug was only evident on the Pi model A where a device was attached
that had no periodic endpoints (e.g. USB pendrive or some wlan devices).
dwc_otg: Fix incorrect URB allocation error handling
If the memory allocation for a dwc_otg_urb failed, the kernel would OOPS
because for some reason a member of the *unallocated* struct was set to
zero. Error handling changed to fail correctly.
dwc_otg: fix potential use-after-free case in interrupt handler
If a transaction had previously aborted, certain interrupts are
enabled to track error counts and reset where necessary. On IN
endpoints the host generates an ACK interrupt near-simultaneously
with completion of transfer. In the case where this transfer had
previously had an error, this results in a use-after-free on
the QTD memory space with a 1-byte length being overwritten to
0x00.
dwc_otg: add handling of SPLIT transaction data toggle errors
Previously a data toggle error on packets from a USB1.1 device behind
a TT would result in the Pi locking up as the driver never handled
the associated interrupt. Patch adds basic retry mechanism and
interrupt acknowledgement to cater for either a chance toggle error or
for devices that have a broken initial toggle state (FT8U232/FT232BM).
dwc_otg: implement tasklet for returning URBs to usbcore hcd layer
The dwc_otg driver interrupt handler for transfer completion will spend
a very long time with interrupts disabled when a URB is completed -
this is because usb_hcd_giveback_urb is called from within the handler
which for a USB device driver with complicated processing (e.g. webcam)
will take an exorbitant amount of time to complete. This results in
missed completion interrupts for other USB packets which lead to them
being dropped due to microframe overruns.
This patch splits returning the URB to the usb hcd layer into a
high-priority tasklet. This will have most benefit for isochronous IN
transfers but will also have incidental benefit where multiple periodic
devices are active at once.
dwc_otg: fix NAK holdoff and allow on split transactions only
This corrects a bug where if a single active non-periodic endpoint
had at least one transaction in its qh, on frnum == MAX_FRNUM the qh
would get skipped and never get queued again. This would result in
a silent device until error detection (automatic or otherwise) would
either reset the device or flush and requeue the URBs.
Additionally the NAK holdoff was enabled for all transactions - this
would potentially stall a HS endpoint for 1ms if a previous error state
enabled this interrupt and the next response was a NAK. Fix so that
only split transactions get held off.
dwc_otg: Call usb_hcd_unlink_urb_from_ep with lock held in completion handler
usb_hcd_unlink_urb_from_ep must be called with the HCD lock held. Calling it
asynchronously in the tasklet was not safe (regression in
c4564d4a1a).
This change unlinks it from the endpoint prior to queueing it for handling in
the tasklet, and also adds a check to ensure the urb is OK to be unlinked
before doing so.
NULL pointer dereference kernel oopses had been observed in usb_hcd_giveback_urb
when a USB device was unplugged/replugged during data transfer. This effect
was reproduced using automated USB port power control, hundreds of replug
events were performed during active transfers to confirm that the problem was
eliminated.
USB fix using a FIQ to implement split transactions
This commit adds a FIQ implementaion that schedules
the split transactions using a FIQ so we don't get
held off by the interrupt latency of Linux
dwc_otg: fix device attributes and avoid kernel warnings on boot
dcw_otg: avoid logging function that can cause panics
See: https://github.com/raspberrypi/firmware/issues/21
Thanks to cleverca22 for fix
dwc_otg: mask correct interrupts after transaction error recovery
The dwc_otg driver will unmask certain interrupts on a transaction
that previously halted in the error state in order to reset the
QTD error count. The various fine-grained interrupt handlers do not
consider that other interrupts besides themselves were unmasked.
By disabling the two other interrupts only ever enabled in DMA mode
for this purpose, we can avoid unnecessary function calls in the
IRQ handler. This will also prevent an unneccesary FIQ interrupt
from being generated if the FIQ is enabled.
dwc_otg: fiq: prevent FIQ thrash and incorrect state passing to IRQ
In the case of a transaction to a device that had previously aborted
due to an error, several interrupts are enabled to reset the error
count when a device responds. This has the side-effect of making the
FIQ thrash because the hardware will generate multiple instances of
a NAK on an IN bulk/interrupt endpoint and multiple instances of ACK
on an OUT bulk/interrupt endpoint. Make the FIQ mask and clear the
associated interrupts.
Additionally, on non-split transactions make sure that only unmasked
interrupts are cleared. This caused a hard-to-trigger but serious
race condition when you had the combination of an endpoint awaiting
error recovery and a transaction completed on an endpoint - due to
the sequencing and timing of interrupts generated by the dwc_otg core,
it was possible to confuse the IRQ handler.
Fix function tracing
dwc_otg: whitespace cleanup in dwc_otg_urb_enqueue
dwc_otg: prevent OOPSes during device disconnects
The dwc_otg_urb_enqueue function is thread-unsafe. In particular the
access of urb->hcpriv, usb_hcd_link_urb_to_ep, dwc_otg_urb->qtd and
friends does not occur within a critical section and so if a device
was unplugged during activity there was a high chance that the
usbcore hub_thread would try to disable the endpoint with partially-
formed entries in the URB queue. This would result in BUG() or null
pointer dereferences.
Fix so that access of urb->hcpriv, enqueuing to the hardware and
adding to usbcore endpoint URB lists is contained within a single
critical section.
dwc_otg: prevent BUG() in TT allocation if hub address is > 16
A fixed-size array is used to track TT allocation. This was
previously set to 16 which caused a crash because
dwc_otg_hcd_allocate_port would read past the end of the array.
This was hit if a hub was plugged in which enumerated as addr > 16,
due to previous device resets or unplugs.
Also add #ifdef FIQ_DEBUG around hcd->hub_port_alloc[], which grows
to a large size if 128 hub addresses are supported. This field is
for debug only for tracking which frame an allocate happened in.
dwc_otg: make channel halts with unknown state less damaging
If the IRQ received a channel halt interrupt through the FIQ
with no other bits set, the IRQ would not release the host
channel and never complete the URB.
Add catchall handling to treat as a transaction error and retry.
dwc_otg: fiq_split: use TTs with more granularity
This fixes certain issues with split transaction scheduling.
- Isochronous multi-packet OUT transactions now hog the TT until
they are completed - this prevents hubs aborting transactions
if they get a periodic start-split out-of-order
- Don't perform TT allocation on non-periodic endpoints - this
allows simultaneous use of the TT's bulk/control and periodic
transaction buffers
This commit will mainly affect USB audio playback.
dwc_otg: fix potential sleep while atomic during urb enqueue
Fixes a regression introduced with eb1b482a. Kmalloc called from
dwc_otg_hcd_qtd_add / dwc_otg_hcd_qtd_create did not always have
the GPF_ATOMIC flag set. Force this flag when inside the larger
critical section.
dwc_otg: make fiq_split_enable imply fiq_fix_enable
Failing to set up the FIQ correctly would result in
"IRQ 32: nobody cared" errors in dmesg.
dwc_otg: prevent crashes on host port disconnects
Fix several issues resulting in crashes or inconsistent state
if a Model A root port was disconnected.
- Clean up queue heads properly in kill_urbs_in_qh_list by
removing the empty QHs from the schedule lists
- Set the halt status properly to prevent IRQ handlers from
using freed memory
- Add fiq_split related cleanup for saved registers
- Make microframe scheduling reclaim host channels if
active during a disconnect
- Abort URBs with -ESHUTDOWN status response, informing
device drivers so they respond in a more correct fashion
and don't try to resubmit URBs
- Prevent IRQ handlers from attempting to handle channel
interrupts if the associated URB was dequeued (and the
driver state was cleared)
dwc_otg: prevent leaking URBs during enqueue
A dwc_otg_urb would get leaked if the HCD enqueue function
failed for any reason. Free the URB at the appropriate points.
dwc_otg: Enable NAK holdoff for control split transactions
Certain low-speed devices take a very long time to complete a
data or status stage of a control transaction, producing NAK
responses until they complete internal processing - the USB2.0
spec limit is up to 500mS. This causes the same type of interrupt
storm as seen with USB-serial dongles prior to c8edb238.
In certain circumstances, usually while booting, this interrupt
storm could cause SD card timeouts.
dwc_otg: Fix for occasional lockup on boot when doing a USB reset
dwc_otg: Don't issue traffic to LS devices in FS mode
Issuing low-speed packets when the root port is in full-speed mode
causes the root port to stop responding. Explicitly fail when
enqueuing URBs to a LS endpoint on a FS bus.
Fix ARM architecture issue with local_irq_restore()
If local_fiq_enable() is called before a local_irq_restore(flags) where
the flags variable has the F bit set, the FIQ will be erroneously disabled.
Fixup arch_local_irq_restore to avoid trampling the F bit in CPSR.
Also fix some of the hacks previously implemented for previous dwc_otg
incarnations.
dwc_otg: fiq_fsm: Base commit for driver rewrite
This commit removes the previous FIQ fixes entirely and adds fiq_fsm.
This rewrite features much more complete support for split transactions
and takes into account several OTG hardware bugs. High-speed
isochronous transactions are also capable of being performed by fiq_fsm.
All driver options have been removed and replaced with:
- dwc_otg.fiq_enable (bool)
- dwc_otg.fiq_fsm_enable (bool)
- dwc_otg.fiq_fsm_mask (bitmask)
- dwc_otg.nak_holdoff (unsigned int)
Defaults are specified such that fiq_fsm behaves similarly to the
previously implemented FIQ fixes.
fiq_fsm: Push error recovery into the FIQ when fiq_fsm is used
If the transfer associated with a QTD failed due to a bus error, the HCD
would retry the transfer up to 3 times (implementing the USB2.0
three-strikes retry in software).
Due to the masking mechanism used by fiq_fsm, it is only possible to pass
a single interrupt through to the HCD per-transfer.
In this instance host channels would fall off the radar because the error
reset would function, but the subsequent channel halt would be lost.
Push the error count reset into the FIQ handler.
fiq_fsm: Implement timeout mechanism
For full-speed endpoints with a large packet size, interrupt latency
runs the risk of the FIQ starting a transaction too late in a full-speed
frame. If the device is still transmitting data when EOF2 for the
downstream frame occurs, the hub will disable the port. This change is
not reflected in the hub status endpoint and the device becomes
unresponsive.
Prevent high-bandwidth transactions from being started too late in a
frame. The mechanism is not guaranteed: a combination of bit stuffing
and hub latency may still result in a device overrunning.
fiq_fsm: fix bounce buffer utilisation for Isochronous OUT
Multi-packet isochronous OUT transactions were subject to a few bounday
bugs. Fix them.
Audio playback is now much more robust: however, an issue stands with
devices that have adaptive sinks - ALSA plays samples too fast.
dwc_otg: Return full-speed frame numbers in HS mode
The frame counter increments on every *microframe* in high-speed mode.
Most device drivers expect this number to be in full-speed frames - this
caused considerable confusion to e.g. snd_usb_audio which uses the
frame counter to estimate the number of samples played.
fiq_fsm: save PID on completion of interrupt OUT transfers
Also add edge case handling for interrupt transports.
Note that for periodic split IN, data toggles are unimplemented in the
OTG host hardware - it unconditionally accepts any PID.
fiq_fsm: add missing case for fiq_fsm_tt_in_use()
Certain combinations of bitrate and endpoint activity could
result in a periodic transaction erroneously getting started
while the previous Isochronous OUT was still active.
fiq_fsm: clear hcintmsk for aborted transactions
Prevents the FIQ from erroneously handling interrupts
on a timed out channel.
fiq_fsm: enable by default
fiq_fsm: fix dequeues for non-periodic split transactions
If a dequeue happened between the SSPLIT and CSPLIT phases of the
transaction, the HCD would never receive an interrupt.
fiq_fsm: Disable by default
fiq_fsm: Handle HC babble errors
The HCTSIZ transfer size field raises a babble interrupt if
the counter wraps. Handle the resulting interrupt in this case.
dwc_otg: fix interrupt registration for fiq_enable=0
Additionally make the module parameter conditional for wherever
hcd->fiq_state is touched.
fiq_fsm: Enable by default
dwc_otg: Fix various issues with root port and transaction errors
Process the host port interrupts correctly (and don't trample them).
Root port hotplug now functional again.
Fix a few thinkos with the transaction error passthrough for fiq_fsm.
fiq_fsm: Implement hack for Split Interrupt transactions
Hubs aren't too picky about which endpoint we send Control type split
transactions to. By treating Interrupt transfers as Control, it is
possible to use the non-periodic queue in the OTG core as well as the
non-periodic FIFOs in the hub itself. This massively reduces the
microframe exclusivity/contention that periodic split transactions
otherwise have to enforce.
It goes without saying that this is a fairly egregious USB specification
violation, but it works.
Original idea by Hans Petter Selasky @ FreeBSD.org.
dwc_otg: FIQ support on SMP. Set up FIQ stack and handler on Core 0 only.
dwc_otg: introduce fiq_fsm_spin(un|)lock()
SMP safety for the FIQ relies on register read-modify write cycles being
completed in the correct order. Several places in the DWC code modify
registers also touched by the FIQ. Protect these by a bare-bones lock
mechanism.
This also makes it possible to run the FIQ and IRQ handlers on different
cores.
fiq_fsm: fix build on bcm2708 and bcm2709 platforms
dwc_otg: put some barriers back where they should be for UP
bcm2709/dwc_otg: Setup FIQ on core 1 if >1 core active
dwc_otg: fixup read-modify-write in critical paths
Be more careful about read-modify-write on registers that the FIQ
also touches.
Guard fiq_fsm_spin_lock with fiq_enable check
fiq_fsm: Falling out of the state machine isn't fatal
This edge case can be hit if the port is disabled while the FIQ is
in the middle of a transaction. Make the effects less severe.
Also get rid of the useless return value.
squash: dwc_otg: Allow to build without SMP
usb: core: make overcurrent messages more prominent
Hub overcurrent messages are more serious than "debug". Increase loglevel.
usb: dwc_otg: Don't use dma_to_virt()
Commit 6ce0d20 changes dma_to_virt() which breaks this driver.
Open code the old dma_to_virt() implementation to work around this.
Limit the use of __bus_to_virt() to cases where transfer_buffer_length
is set and transfer_buffer is not set. This is done to increase the
chance that this driver will also work on ARCH_BCM2835.
transfer_buffer should not be NULL if the length is set, but the
comment in the code indicates that there are situations where this
might happen. drivers/usb/isp1760/isp1760-hcd.c also has a similar
comment pointing to a possible: 'usb storage / SCSI bug'.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: Fix crash when fiq_enable=0
dwc_otg: fiq_fsm: Make high-speed isochronous strided transfers work properly
Certain low-bandwidth high-speed USB devices (specialist audio devices,
compressed-frame webcams) have packet intervals > 1 microframe.
Stride these transfers in the FIQ by using the start-of-frame interrupt
to restart the channel at the right time.
dwc_otg: Force host mode to fix incorrect compute module boards
dwc_otg: Add ARCH_BCM2835 support
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: Simplify FIQ irq number code
Dropping ATAGS means we can simplify the FIQ irq number code.
Also add error checking on the returned irq number.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: Remove duplicate gadget probe/unregister function
dwc_otg: Properly set the HFIR
Douglas Anderson reported:
According to the most up to date version of the dwc2 databook, the FRINT
field of the HFIR register should be programmed to:
* 125 us * (PHY clock freq for HS) - 1
* 1000 us * (PHY clock freq for FS/LS) - 1
This is opposed to older versions of the doc that claimed it should be:
* 125 us * (PHY clock freq for HS)
* 1000 us * (PHY clock freq for FS/LS)
and reported lower timing jitter on a USB analyser
dcw_otg: trim xfer length when buffer larger than allocated size is received
dwc_otg: Don't free qh align buffers in atomic context
dwc_otg: Enable the hack for Split Interrupt transactions by default
dwc_otg.fiq_fsm_mask=0xF has long been a suggestion for users with audio stutters or other USB bandwidth issues.
So far we are aware of many success stories but no failure caused by this setting.
Make it a default to learn more.
See: https://www.raspberrypi.org/forums/viewtopic.php?f=28&t=70437
Signed-off-by: popcornmix <popcornmix@gmail.com>
This is a hack until a proper solution is agreed upon.
Martin Sperl is doing some work in this area.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Transfers larger than 32k cause repeated clicking with I2S soundcards.
The exact reason is yet unknown, so limit to 32k as bcm2708-dmaengine
did as an intermediate fix.
Load driver early since at least bcm2708_fb doesn't support deferred
probing and even if it did, we don't want the video driver deferred.
Support the legacy DMA API which is needed by bcm2708_fb.
Don't mask out channel 2.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2835-dma supports residue reporting at burst level but didn't report
this via the residue_granularity field.
Without this field set properly we get playback issues with I2S cards.
[by HiassofT, taken from bcm2708-dmaengine]
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Add slave transfer capability to BCM2835 dmaengine driver.
This patch is pulled from the bcm2708-dmaengine driver in the
Raspberry Pi repo. The work was done by Gellert Weisz.
Tested using the bcm2835-mmc driver from the same repo.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
The VideoCore bootloader passes in Serial number and
Revision number through Device Tree. Make these available to
userspace through /proc/cpuinfo.
Mainline status:
There is a commit in linux-next that standardize passing the serial
number through Device Tree (string: /serial-number):
ARM: 8355/1: arch: Show the serial number from devicetree in cpuinfo
There was an attempt to do the same with the revision number, but it
didn't get in:
[PATCH v2 1/2] arm: devtree: Set system_rev from DT revision
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
The spi-bcm2835 driver automatically uses GPIO chip-selects due to
some unreliability of the native ones. In doing so it chooses the
same pins as the native chip-selects would use, but the existing
code always uses pins 7 and 8, wherever the SPI function is mapped.
Search the pinctrl group assigned to the driver for pins that
correspond to native chip-selects, and use those for GPIO chip-
selects.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
When dynamically unloading overlays, it is important that freed pins are
restored to being inputs to prevent functions from being enabled in
multiple places at once.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Although the GPIO controller can generate three interrupts (four counting
the common one), the device tree files currently only specify two. In the
absence of the third, simply don't register that interrupt (as opposed to
registering 0), which has the effect of making it impossible to generate
interrupts for GPIOs 46-53 which, since they share pins with the SD card
interface, is unlikely to be a problem.
Contrary to the documentation, the BCM2835 GPIO controller actually has
four interrupt lines - one each for the three IRQ groups and one common. Rather
confusingly, the GPIO interrupt groups don't correspond directly with the GPIO
control banks. Instead, GPIOs 0-27 generate IRQ GPIO0, 28-45 GPIO1 and
46-53 GPIO2.
Awkwardly, the GPIOS for IRQ GPIO1 straddle two 32-entry GPIO banks, so it is
cleaner to split out a function to process the interrupts for a single GPIO
bank.
This bug has only just been observed because GPIOs above 27 can only be
accessed on an old Raspberry Pi with the optional P5 header fitted, where
the pins are often used for I2S instead.
Add a duplicate irq range with an offset on the hwirq's so the
driver can detect that enable_fiq() is used.
Tested with downstream dwc_otg USB controller driver.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
The old arch-specific IRQ macros included a dsb to ensure the
write to clear the mailbox interrupt completed before returning
from the interrupt. The BCM2836 irqchip driver needs the same
precaution to avoid spurious interrupts.
Spurious interrupts are still possible for other reasons,
though, so trap them early.
See commit dae803e165 -- the warning is
expected sometimes when using CMA. However, that commit still spams
my kernel log with these warnings.
Signed-off-by: Eric Anholt <eric@anholt.net>
tty_port_hangup sets a port's tty field to NULL (holding the port lock),
but uart_tx_stopped, called from __uart_start (with the port lock),
uses the tty field without checking for NULL.
Change uart_tx_stopped to treat a NULL tty field as another stopped
indication.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
If a previously-set alarm was disabled and then triggered, it may still
be pending when a new alarm is configured.
Then, if the alarm is enabled before the pending alarm is cleared, then
an interrupt is immediately raised.
Unfortunately, when the alarm is cleared and enabled during the same I²C
block write, the chip (at least the DS1339 I have) considers that the
alarm is enabled before it is cleared, and raises an interrupt.
This patch ensures that the pending alarm is cleared before the alarm is
enabled.
Signed-off-by: Nicolas Boullis <nboullis@debian.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
smsc95xx is adjusting truesize when it shouldn't, and following a recent patch from Eric this is now triggering warnings.
This patch stops smsc95xx from changing truesize.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
commit 554a5ccc4e upstream.
If we hit this error when mounted with errors=continue or
errors=remount-ro:
EXT4-fs error (device loop0): ext4_mb_mark_diskspace_used:2940: comm ext4.exe: Allocating blocks 5090-6081 which overlap fs metadata
then ext4_mb_new_blocks() will call ext4_mb_release_context() and try to
continue. However, ext4_mb_release_context() is the wrong thing to call
here since we are still actually using the allocation context.
Instead, just error out. We could retry the allocation, but there is a
possibility of getting stuck in an infinite loop instead, so this seems
safer.
[ Fixed up so we don't return EAGAIN to userspace. --tytso ]
Fixes: 8556e8f3b6 ("ext4: Don't allow new groups to be added during block allocation")
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c65d5c6c81 upstream.
If we encounter a filesystem error during orphan cleanup, we should stop.
Otherwise, we may end up in an infinite loop where the same inode is
processed again and again.
EXT4-fs (loop0): warning: checktime reached, running e2fsck is recommended
EXT4-fs error (device loop0): ext4_mb_generate_buddy:758: group 2, block bitmap and bg descriptor inconsistent: 6117 vs 0 free clusters
Aborting journal on device loop0-8.
EXT4-fs (loop0): Remounting filesystem read-only
EXT4-fs error (device loop0) in ext4_free_blocks:4895: Journal has aborted
EXT4-fs error (device loop0) in ext4_do_update_inode:4893: Journal has aborted
EXT4-fs error (device loop0) in ext4_do_update_inode:4893: Journal has aborted
EXT4-fs error (device loop0) in ext4_ext_remove_space:3068: IO failure
EXT4-fs error (device loop0) in ext4_ext_truncate:4667: Journal has aborted
EXT4-fs error (device loop0) in ext4_orphan_del:2927: Journal has aborted
EXT4-fs error (device loop0) in ext4_do_update_inode:4893: Journal has aborted
EXT4-fs (loop0): Inode 16 (00000000618192a0): orphan list check failed!
[...]
EXT4-fs (loop0): Inode 16 (0000000061819748): orphan list check failed!
[...]
EXT4-fs (loop0): Inode 16 (0000000061819bf0): orphan list check failed!
[...]
See-also: c9eb13a910 ("ext4: fix hang when processing corrupted orphaned inode list")
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b9554dc5b upstream.
If s_reserved_gdt_blocks is extremely large, it's possible for
ext4_init_block_bitmap(), which is called when ext4 sets up an
uninitialized block bitmap, to corrupt random kernel memory. Add the
same checks which e2fsck has --- it must never be larger than
blocksize / sizeof(__u32) --- and then add a backup check in
ext4_init_block_bitmap() in case the superblock gets modified after
the file system is mounted.
Reported-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6a7fd522a7 upstream.
If ext4_fill_super() fails early, it's possible for ext4_evict_inode()
to call ext4_should_journal_data() before superblock options and flags
are fully set up. In that case, the iput() on the journal inode can
end up causing a BUG().
Work around this problem by reordering the tests so we only call
ext4_should_journal_data() after we know it's not the journal inode.
Fixes: 2d859db3e4 ("ext4: fix data corruption in inodes with journalled data")
Fixes: 2b405bfa84 ("ext4: fix data=journal fast mount/umount hang")
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 646caa9c8e upstream.
Commit 06bd3c36a7 (ext4: fix data exposure after a crash) uncovered a
deadlock in ext4_writepages() which was previously much harder to hit.
After this commit xfstest generic/130 reproduces the deadlock on small
filesystems.
The problem happens when ext4_do_update_inode() sets LARGE_FILE feature
and marks current inode handle as synchronous. That subsequently results
in ext4_journal_stop() called from ext4_writepages() to block waiting for
transaction commit while still holding page locks, reference to io_end,
and some prepared bio in mpd structure each of which can possibly block
transaction commit from completing and thus results in deadlock.
Fix the problem by releasing page locks, io_end reference, and
submitting prepared bio before calling ext4_journal_stop().
[ Changed to defer the call to ext4_journal_stop() only if the handle
is synchronous. --tytso ]
Reported-and-tested-by: Eryu Guan <eguan@redhat.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f70749ca42 upstream.
An extent with lblock = 4294967295 and len = 1 will pass the
ext4_valid_extent() test:
ext4_lblk_t last = lblock + len - 1;
if (len == 0 || lblock > last)
return 0;
since last = 4294967295 + 1 - 1 = 4294967295. This would later trigger
the BUG_ON(es->es_lblk + es->es_len < es->es_lblk) in ext4_es_end().
We can simplify it by removing the - 1 altogether and changing the test
to use lblock + len <= lblock, since now if len = 0, then lblock + 0 ==
lblock and it fails, and if len > 0 then lblock + len > lblock in order
to pass (i.e. it doesn't overflow).
Fixes: 5946d0893 ("ext4: check for overlapping extents in ext4_valid_extent_entries()")
Fixes: 2f974865f ("ext4: check for zero length extent explicitly")
Cc: Eryu Guan <guaneryu@gmail.com>
Signed-off-by: Phil Turnbull <phil.turnbull@oracle.com>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2c1659b4f upstream.
As suggested by the serial port infrastructure documentation, the IRQ is
requested in ->startup(). However, it is never freed in the ->shutdown()
hook.
With simple systems that open the serial port once for all and always
have at least one process that keep the serial port opened, there was no
problem. But with a more complicated system (*cough* systemd *cough*),
the serial port is opened/closed many times, which at some point no
processes having the serial port open at all. Due to this ->startup()
gets called again, tries to request_irq() again, which fails.
Fixes: 30530791a7 ("serial: mvebu-uart: initial support for Armada-3700 serial port")
Cc: Ofer Heifetz <oferh@marvell.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5f070e81be upstream.
When there is more data to be processed, the current test in
scatterwalk_done may prevent us from calling pagedone even when
we should.
In particular, if we're on an SG entry spanning multiple pages
where the last page is not a full page, we will incorrectly skip
calling pagedone on the second last page.
This patch fixes this by adding a separate test for whether we've
reached the end of a page.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b30bdfa864 upstream.
As it is if you ask for a sync gcm you may actually end up with
an async one because it does not filter out async implementations
of ghash.
This patch fixes this by adding the necessary filter when looking
for ghash.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit da7d3abe1c upstream.
This reverts commit 790d849bf8.
Using a v4.7-rc7 kernel on a HP ProLiant triggered following messages
pcc-cpufreq: (v1.10.00) driver loaded with frequency limits: 1200 MHz, 2800 MHz
cpufreq: ondemand governor failed, too long transition latency of HW, fallback to performance governor
The last line was shown for each CPU in the system.
Testing v4.5 (where commit 790d849b was integrated) triggered
similar messages. Same behaviour on a 2nd HP Proliant system.
So commit 790d849bf (cpufreq: pcc-cpufreq: update default value of
cpuinfo_transition_latency) causes the system to use performance
governor which, I guess, was not the intention of the patch.
Enabling debug output in pcc-cpufreq provides following verbose output:
pcc-cpufreq: (v1.10.00) driver loaded with frequency limits: 1200 MHz, 2800 MHz
pcc_get_offset: for CPU 0: pcc_cpu_data input_offset: 0x44, pcc_cpu_data output_offset: 0x48
init: policy->max is 2800000, policy->min is 1200000
get: get_freq for CPU 0
get: SUCCESS: (virtual) output_offset for cpu 0 is 0xffffc9000d7c0048, contains a value of: 0xff06. Speed is: 168000 MHz
cpufreq: ondemand governor failed, too long transition latency of HW, fallback to performance governor
target: CPU 0 should go to target freq: 2800000 (virtual) input_offset is 0xffffc9000d7c0044
target: was SUCCESSFUL for cpu 0
I am asking to revert 790d849bf to re-enable usage of ondemand
governor with pcc-cpufreq.
Fixes: 790d849bf (cpufreq: pcc-cpufreq: update default value of cpuinfo_transition_latency)
Signed-off-by: Andreas Herrmann <aherrmann@suse.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 47be61845c upstream.
We triggered soft-lockup under stress test which
open/access/write/close one file concurrently on more than
five different CPUs:
WARN: soft lockup - CPU#0 stuck for 11s! [who:30631]
...
[<ffffffc0003986f8>] dput+0x100/0x298
[<ffffffc00038c2dc>] terminate_walk+0x4c/0x60
[<ffffffc00038f56c>] path_lookupat+0x5cc/0x7a8
[<ffffffc00038f780>] filename_lookup+0x38/0xf0
[<ffffffc000391180>] user_path_at_empty+0x78/0xd0
[<ffffffc0003911f4>] user_path_at+0x1c/0x28
[<ffffffc00037d4fc>] SyS_faccessat+0xb4/0x230
->d_lock trylock may failed many times because of concurrently
operations, and dput() may execute a long time.
Fix this by replacing cpu_relax() with cond_resched().
dput() used to be sleepable, so make it sleepable again
should be safe.
Signed-off-by: Wei Fang <fangwei1@huawei.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e390b2b2f upstream.
This reverts commit f9054c70d2 ("mm, mempool: only set __GFP_NOMEMALLOC
if there are free elements").
There has been a report about OOM killer invoked when swapping out to a
dm-crypt device. The primary reason seems to be that the swapout out IO
managed to completely deplete memory reserves. Ondrej was able to
bisect and explained the issue by pointing to f9054c70d2 ("mm,
mempool: only set __GFP_NOMEMALLOC if there are free elements").
The reason is that the swapout path is not throttled properly because
the md-raid layer needs to allocate from the generic_make_request path
which means it allocates from the PF_MEMALLOC context. dm layer uses
mempool_alloc in order to guarantee a forward progress which used to
inhibit access to memory reserves when using page allocator. This has
changed by f9054c70d2 ("mm, mempool: only set __GFP_NOMEMALLOC if
there are free elements") which has dropped the __GFP_NOMEMALLOC
protection when the memory pool is depleted.
If we are running out of memory and the only way forward to free memory
is to perform swapout we just keep consuming memory reserves rather than
throttling the mempool allocations and allowing the pending IO to
complete up to a moment when the memory is depleted completely and there
is no way forward but invoking the OOM killer. This is less than
optimal.
The original intention of f9054c70d2 was to help with the OOM
situations where the oom victim depends on mempool allocation to make a
forward progress. David has mentioned the following backtrace:
schedule
schedule_timeout
io_schedule_timeout
mempool_alloc
__split_and_process_bio
dm_request
generic_make_request
submit_bio
mpage_readpages
ext4_readpages
__do_page_cache_readahead
ra_submit
filemap_fault
handle_mm_fault
__do_page_fault
do_page_fault
page_fault
We do not know more about why the mempool is depleted without being
replenished in time, though. In any case the dm layer shouldn't depend
on any allocations outside of the dedicated pools so a forward progress
should be guaranteed. If this is not the case then the dm should be
fixed rather than papering over the problem and postponing it to later
by accessing more memory reserves.
mempools are a mechanism to maintain dedicated memory reserves to
guaratee forward progress. Allowing them an unbounded access to the
page allocator memory reserves is going against the whole purpose of
this mechanism.
Bisected by Ondrej Kozina.
[akpm@linux-foundation.org: coding-style fixes]
Link: http://lkml.kernel.org/r/20160721145309.GR26379@dhcp22.suse.cz
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reported-by: Ondrej Kozina <okozina@redhat.com>
Reviewed-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: NeilBrown <neilb@suse.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Mikulas Patocka <mpatocka@redhat.com>
Cc: Ondrej Kozina <okozina@redhat.com>
Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Cc: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9ebce595f6 upstream.
fuse_flush() calls write_inode_now() that triggers writeback, but actual
writeback will happen later, on fuse_sync_writes(). If an error happens,
fuse_writepage_end() will set error bit in mapping->flags. So, we have to
check mapping->flags after fuse_sync_writes().
Signed-off-by: Maxim Patlasov <mpatlasov@virtuozzo.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Fixes: 4d99ff8f12 ("fuse: Turn writeback cache on")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ac7f052b9e upstream.
Due to implementation of fuse writeback filemap_write_and_wait_range() does
not catch errors. We have to do this directly after fuse_sync_writes()
Signed-off-by: Alexey Kuznetsov <kuznet@virtuozzo.com>
Signed-off-by: Maxim Patlasov <mpatlasov@virtuozzo.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Fixes: 4d99ff8f12 ("fuse: Turn writeback cache on")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4ce827b4cc upstream.
In kernel bug 150021, a kernel panic was reported when restoring a
hibernate image. Only a picture of the oops was reported, so I can't
paste the whole thing here. But here are the most interesting parts:
kernel tried to execute NX-protected page - exploit attempt? (uid: 0)
BUG: unable to handle kernel paging request at ffff8804615cfd78
...
RIP: ffff8804615cfd78
RSP: ffff8804615f0000
RBP: ffff8804615cfdc0
...
Call Trace:
do_signal+0x23
exit_to_usermode_loop+0x64
...
The RIP is on the same page as RBP, so it apparently started executing
on the stack.
The bug was bisected to commit ef0f3ed5a4 (x86/asm/power: Create
stack frames in hibernate_asm_64.S), which in retrospect seems quite
dangerous, since that code saves and restores the stack pointer from a
global variable ('saved_context').
There are a lot of moving parts in the hibernate save and restore paths,
so I don't know exactly what caused the panic. Presumably, a FRAME_END
was executed without the corresponding FRAME_BEGIN, or vice versa. That
would corrupt the return address on the stack and would be consistent
with the details of the above panic.
[ rjw: One major problem is that by the time the FRAME_BEGIN in
restore_registers() is executed, the stack pointer value may not
be valid any more. Namely, the stack area pointed to by it
previously may have been overwritten by some image memory contents
and that page frame may now be used for whatever different purpose
it had been allocated for before hibernation. In that case, the
FRAME_BEGIN will corrupt that memory. ]
Instead of doing the frame pointer save/restore around the bounds of the
affected functions, just do it around the call to swsusp_save().
That has the same effect of ensuring that if swsusp_save() sleeps, the
frame pointers will be correct. It's also a much more obviously safe
way to do it than the original patch. And objtool still doesn't report
any warnings.
Fixes: ef0f3ed5a4 (x86/asm/power: Create stack frames in hibernate_asm_64.S)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=150021
Reported-by: Andre Reinke <andre.reinke@mailbox.org>
Tested-by: Andre Reinke <andre.reinke@mailbox.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4b703305d9 upstream.
Usually, after we have found the proper microcode blob for the current
machine, we stash it away for later use with save_microcode_in_initrd().
However, with builtin microcode which doesn't come from the initrd, we
don't call that function because CONFIG_BLK_DEV_INITRD=n and even if
set, we don't have a valid initrd.
In order to fix this, let's make save_microcode_in_initrd() an
fs_initcall which runs before rootfs_initcall() as this was the time it
was called previously through:
rootfs_initcall(populate_rootfs)
|-> free_initrd()
|-> free_initrd_mem()
|-> save_microcode_in_initrd()
Also, we make it run independently from initrd functionality being
present or not.
And since it is called in the microcode loader only now, we can also
make it static.
Reported-and-tested-by: Jim Bos <jim876@xs4all.nl>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1465225850-7352-3-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05eb6e7263 upstream.
Radix trees may be used not only for storing page cache pages, so
unconditionally accounting radix tree nodes to the current memory cgroup
is bad: if a radix tree node is used for storing data shared among
different cgroups we risk pinning dead memory cgroups forever.
So let's only account radix tree nodes if it was explicitly requested by
passing __GFP_ACCOUNT to INIT_RADIX_TREE. Currently, we only want to
account page cache entries, so mark mapping->page_tree so.
Fixes: 58e698af4c ("radix-tree: account radix_tree_node to memory cgroup")
Link: http://lkml.kernel.org/r/1470057188-7864-1-git-send-email-vdavydov@virtuozzo.com
Signed-off-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 844e3be476 upstream.
Classic BPF JIT was never ported completely to work on little endian
powerpc. However, it can be enabled and will crash the system when used.
As such, disable use of BPF JIT on ppc64le.
Fixes: 7c105b63bd ("powerpc: Add CONFIG_CPU_LITTLE_ENDIAN kernel config option.")
Reported-by: Thadeu Lima de Souza Cascardo <cascardo@redhat.com>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a3aa256b72 upstream.
The PE primary bus cannot be got from its child devices when having
full hotplug in error recovery. The PE primary bus is cached, which
is done in commit <05ba75f84864> ("powerpc/eeh: Fix stale cached primary
bus"). In eeh_reset_device(), the flag (EEH_PE_PRI_BUS) is cleared
before the PCI hot remove. eeh_pe_bus_get() then returns NULL as the
PE primary bus in pnv_eeh_reset() and it crashes the kernel eventually.
This fixes the issue by clearing the flag (EEH_PE_PRI_BUS) before the
PCI hot add. With it, the PowerNV EEH reset backend (pnv_eeh_reset())
can get valid PE primary bus through eeh_pe_bus_get().
Fixes: 67086e32b5 ("powerpc/eeh: powerpc/eeh: Support error recovery for VF PE")
Reported-by: Pridhiviraj Paidipeddi <ppaiddipe@in.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a47241cdee upstream.
Presently, a corrupted or malicious UDF filesystem containing a very large
number (or cycle) of Logical Volume Integrity Descriptor extent
indirections may trigger a stack overflow and kernel panic in
udf_load_logicalvolint() on mount.
Replace the unnecessary recursion in udf_load_logicalvolint() with
simple iteration. Set an arbitrary limit of 1000 indirections (which would
have almost certainly overflowed the stack without this fix), and treat
such cases as if there were no LVID.
Signed-off-by: Alden Tondettar <alden.tondettar@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1886297ce0 upstream.
The following BUG_ON() crash was reported on QEMU/i386:
kernel BUG at arch/x86/mm/physaddr.c:79!
Call Trace:
phys_mem_access_prot_allowed
mmap_mem
? mmap_region
mmap_region
do_mmap
vm_mmap_pgoff
SyS_mmap_pgoff
do_int80_syscall_32
entry_INT80_32
after commit:
edfe63ec97 ("x86/mtrr: Fix Xorg crashes in Qemu sessions")
PAT is now set to disabled state when MTRRs are disabled.
Thus, reactivating the __pa(high_memory) check in
phys_mem_access_prot_allowed().
When CONFIG_DEBUG_VIRTUAL is set, __pa() calls __phys_addr(),
which in turn calls slow_virt_to_phys() for 'high_memory'.
Because 'high_memory' is set to (the max direct mapped virt
addr + 1), it is not a valid virtual address. Hence,
slow_virt_to_phys() returns 0 and hit the BUG_ON. Using
__pa_nodebug() instead of __pa() will fix this BUG_ON.
However, this code block, originally written for Pentiums and
earlier, is no longer adequate since a 32-bit Xen guest has
MTRRs disabled and supports ZONE_HIGHMEM. In this setup,
this code sets UC attribute for accessing RAM in high memory
range.
Delete this code block as it has been unused for a long time.
Reported-by: kernel test robot <ying.huang@linux.intel.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: xen-devel@lists.xenproject.org
Link: http://lkml.kernel.org/r/1460403360-25441-1-git-send-email-toshi.kani@hpe.com
Link: https://lkml.org/lkml/2016/4/1/608
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit edfe63ec97 upstream.
A Xorg failure on qemu32 was reported as a regression [1] caused by
commit 9cd25aac1f ("x86/mm/pat: Emulate PAT when it is disabled").
This patch fixes the Xorg crash.
Negative effects of this regression were the following two failures [2]
in Xorg on QEMU with QEMU CPU model "qemu32" (-cpu qemu32), which were
triggered by the fact that its virtual CPU does not support MTRRs.
#1. copy_process() failed in the check in reserve_pfn_range()
copy_process
copy_mm
dup_mm
dup_mmap
copy_page_range
track_pfn_copy
reserve_pfn_range
A WC map request was tracked as WC in memtype, which set a PTE as
UC (pgprot) per __cachemode2pte_tbl[]. This led to this error in
reserve_pfn_range() called from track_pfn_copy(), which obtained
a pgprot from a PTE. It converts pgprot to page_cache_mode, which
does not necessarily result in the original page_cache_mode since
__cachemode2pte_tbl[] redirects multiple types to UC.
#2. error path in copy_process() then hit WARN_ON_ONCE in
untrack_pfn().
x86/PAT: Xorg:509 map pfn expected mapping type uncached-
minus for [mem 0xfd000000-0xfdffffff], got write-combining
Call Trace:
dump_stack
warn_slowpath_common
? untrack_pfn
? untrack_pfn
warn_slowpath_null
untrack_pfn
? __kunmap_atomic
unmap_single_vma
? pagevec_move_tail_fn
unmap_vmas
exit_mmap
mmput
copy_process.part.47
_do_fork
SyS_clone
do_syscall_32_irqs_on
entry_INT80_32
These negative effects are caused by two separate bugs, but they
can be addressed in separate patches. Fixing the pat_init() issue
described below addresses the root cause, and avoids Xorg to hit
these cases.
When the CPU does not support MTRRs, MTRR does not call pat_init(),
which leaves PAT enabled without initializing PAT. This pat_init()
issue is a long-standing issue, but manifested as issue #1 (and then
hit issue #2) with the above-mentioned commit because the memtype
now tracks cache attribute with 'page_cache_mode'.
This pat_init() issue existed before the commit, but we used pgprot
in memtype. Hence, we did not have issue #1 before. But WC request
resulted in WT in effect because WC pgrot is actually WT when PAT
is not initialized. This is not how it was designed to work. When
PAT is set to disable properly, WC is converted to UC. The use of
WT can result in a system crash if the target range does not support
WT. Fortunately, nobody ran into such issue before.
To fix this pat_init() issue, PAT code has been enhanced to provide
pat_disable() interface. Call this interface when MTRRs are disabled.
By setting PAT to disable properly, PAT bypasses the memtype check,
and avoids issue #1.
[1]: https://lkml.org/lkml/2016/3/3/828
[2]: https://lkml.org/lkml/2016/3/4/775
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Borislav Petkov <bp@suse.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luis R. Rodriguez <mcgrof@suse.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: elliott@hpe.com
Cc: konrad.wilk@oracle.com
Cc: paul.gortmaker@windriver.com
Cc: xen-devel@lists.xenproject.org
Link: http://lkml.kernel.org/r/1458769323-24491-5-git-send-email-toshi.kani@hpe.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 86a574de45 upstream.
Don't allow RNDADDTOENTCNT or RNDADDENTROPY to accept a negative
entropy value. It doesn't make any sense to subtract from the entropy
counter, and it can trigger a warning:
random: negative entropy/overflow: pool input count -40000
------------[ cut here ]------------
WARNING: CPU: 3 PID: 6828 at drivers/char/random.c:670[< none
>] credit_entropy_bits+0x21e/0xad0 drivers/char/random.c:670
Modules linked in:
CPU: 3 PID: 6828 Comm: a.out Not tainted 4.7.0-rc4+ #4
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
ffffffff880b58e0 ffff88005dd9fcb0 ffffffff82cc838f ffffffff87158b40
fffffbfff1016b1c 0000000000000000 0000000000000000 ffffffff87158b40
ffffffff83283dae 0000000000000009 ffff88005dd9fcf8 ffffffff8136d27f
Call Trace:
[< inline >] __dump_stack lib/dump_stack.c:15
[<ffffffff82cc838f>] dump_stack+0x12e/0x18f lib/dump_stack.c:51
[<ffffffff8136d27f>] __warn+0x19f/0x1e0 kernel/panic.c:516
[<ffffffff8136d48c>] warn_slowpath_null+0x2c/0x40 kernel/panic.c:551
[<ffffffff83283dae>] credit_entropy_bits+0x21e/0xad0 drivers/char/random.c:670
[< inline >] credit_entropy_bits_safe drivers/char/random.c:734
[<ffffffff8328785d>] random_ioctl+0x21d/0x250 drivers/char/random.c:1546
[< inline >] vfs_ioctl fs/ioctl.c:43
[<ffffffff8185316c>] do_vfs_ioctl+0x18c/0xff0 fs/ioctl.c:674
[< inline >] SYSC_ioctl fs/ioctl.c:689
[<ffffffff8185405f>] SyS_ioctl+0x8f/0xc0 fs/ioctl.c:680
[<ffffffff86a995c0>] entry_SYSCALL_64_fastpath+0x23/0xc1
arch/x86/entry/entry_64.S:207
---[ end trace 5d4902b2ba842f1f ]---
This was triggered using the test program:
// autogenerated by syzkaller (http://github.com/google/syzkaller)
int main() {
int fd = open("/dev/random", O_RDWR);
int val = -5000;
ioctl(fd, RNDADDTOENTCNT, &val);
return 0;
}
It's harmless in that (a) only root can trigger it, and (b) after
complaining the code never does let the entropy count go negative, but
it's better to simply not allow this userspace from passing in a
negative entropy value altogether.
Google-Bug-Id: #29575089
Reported-By: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 43160ffd12 upstream.
Use regulator_list_voltage_linear_range in rpm_smps_ldo_ops_fixed is
wrong because it is used for fixed regulator without any linear range.
The rpm_smps_ldo_ops_fixed is used for pm8941_lnldo which has fixed_uV
set and n_voltages = 1. In this case, regulator_list_voltage() can return
rdev->desc->fixed_uV without .list_voltage implementation.
Fixes: 3bfbb4d1a4 ("regulator: qcom_smd: add list_voltage callback")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2aee309d3e upstream.
A failure in the get_txreq() inline will result in a
slow path retry using __get_txreq().
__get_txreq() attempts to procure the qp s_lock, which
is already held in all callers.
Fix by deleting the s_lock maintenance in __get_txreq()
and add sparse syntax hooks to future proof the code.
Cc: Stable <stable@vger.kernel.org> # 4.6+
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 896ce45da2 upstream.
There are several computatations of the sc in the
ud receive routine.
Besides the code duplication, all are wrong when the
sc is greater than 15. In that case the code incorrectly
or's a 1 into the computed sc instead of 1 shifted left
by 4.
Fix precomputed sc5 by using an already implemented routine
hdr2sc() and deleting flawed duplicated code.
Cc: Stable <stable@vger.kernel.org> # 4.6+
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a7ae81952c upstream.
Many Intel systems the BIOS declares a SystemIO OpRegion below the SMBus
PCI device as can be seen in ACPI DSDT table from Lenovo Yoga 900:
Device (SBUS)
{
OperationRegion (SMBI, SystemIO, (SBAR << 0x05), 0x10)
Field (SMBI, ByteAcc, NoLock, Preserve)
{
HSTS, 8,
Offset (0x02),
HCON, 8,
HCOM, 8,
TXSA, 8,
DAT0, 8,
DAT1, 8,
HBDR, 8,
PECR, 8,
RXSA, 8,
SDAT, 16
}
There are also bunch of AML methods that that the BIOS can use to access
these fields. Most of the systems in question AML methods accessing the
SMBI OpRegion are never used.
Now, because of this SMBI OpRegion many systems fail to load the SMBus
driver with an error looking like one below:
ACPI Warning: SystemIO range 0x0000000000003040-0x000000000000305F
conflicts with OpRegion 0x0000000000003040-0x000000000000304F
(\_SB.PCI0.SBUS.SMBI) (20160108/utaddress-255)
ACPI: If an ACPI driver is available for this device, you should use
it instead of the native driver
The reason is that this SMBI OpRegion conflicts with the PCI BAR used by
the SMBus driver.
It turns out that we can install a custom SystemIO address space handler
for the SMBus device to intercept all accesses through that OpRegion. This
allows us to share the PCI BAR with the AML code if it for some reason is
using it. We do not expect that this OpRegion handler will ever be called
but if it is we print a warning and prevent all access from the SMBus
driver itself.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=110041
Reported-by: Andy Lutomirski <luto@kernel.org>
Reported-by: Pali Rohár <pali.rohar@gmail.com>
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f626300a3e ]
tcp_select_initial_window() intends to advertise a window
scaling for the maximum possible window size. To do so,
it considers the maximum of net.ipv4.tcp_rmem[2] and
net.core.rmem_max as the only possible upper-bounds.
However, users with CAP_NET_ADMIN can use SO_RCVBUFFORCE
to set the socket's receive buffer size to values
larger than net.ipv4.tcp_rmem[2] and net.core.rmem_max.
Thus, SO_RCVBUFFORCE is effectively ignored by
tcp_select_initial_window().
To fix this, consider the maximum of net.ipv4.tcp_rmem[2],
net.core.rmem_max and socket's initial buffer space.
Fixes: b0573dea1f ("[NET]: Introduce SO_{SND,RCV}BUFFORCE socket options")
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Suggested-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e3a3b62601 ]
macsec_decrypt() is not called when validation is disabled and so
macsec_skb_cb(skb)->rx_sa is not set; but it is used later in
macsec_post_decrypt(), ensure that it's always initialized.
Fixes: c09440f7dc ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Beniamino Galvani <bgalvani@redhat.com>
Acked-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ea06f71764 ]
Default kernel behavior is to delete IPv6 addresses on link
down, which entails deletion of the multicast and the
subnet-router anycast addresses. These deletions do not
happen with sysctl setting to keep global IPv6 addresses on
link down, so every link down/up causes an increment of the
anycast and multicast refcounts. These bogus refcounts may
stop these addrs from being removed on subsequent calls to
delete them. The solution is to leave the groups for the
multicast and subnet anycast on link down for the callflow
when global IPv6 addresses are kept.
Fixes: f1705ec197 ("net: ipv6: Make address flushing on ifdown optional")
Signed-off-by: Mike Manning <mmanning@brocade.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit baedbe5588 ]
Commit 8626c56c82 ("bridge: fix potential use-after-free when hook
returns QUEUE or STOLEN verdict") caused LLDP packets arriving through a
bridge port to be re-injected to the Rx path with skb->dev set to the
bridge device, but this breaks the lldpad daemon.
The lldpad daemon opens a packet socket with protocol set to ETH_P_LLDP
for any valid device on the system, which doesn't not include soft
devices such as bridge and VLAN.
Since packet sockets (ptype_base) are processed in the Rx path after the
Rx handler, LLDP packets with skb->dev set to the bridge device never
reach the lldpad daemon.
Fix this by making the bridge's Rx handler re-inject LLDP packets with
RX_HANDLER_PASS, which effectively restores the behaviour prior to the
mentioned commit.
This means netfilter will never receive LLDP packets coming through a
bridge port, as I don't see a way in which we can have okfn() consume
the packet without breaking existing behaviour. I've already carried out
a similar fix for STP packets in commit 56fae404fb ("bridge: Fix
incorrect re-injection of STP packets").
Fixes: 8626c56c82 ("bridge: fix potential use-after-free when hook returns QUEUE or STOLEN verdict")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 18d3df3eab ]
macsec can't cope with mtu frames which need vlan tag insertion, and
vlan device set the default mtu equal to the underlying dev's one.
By default vlan over macsec devices use invalid mtu, dropping
all the large packets.
This patch adds a netif helper to check if an upper vlan device
needs mtu reduction. The helper is used during vlan devices
initialization to set a valid default and during mtu updating to
forbid invalid, too bit, mtu values.
The helper currently only check if the lower dev is a macsec device,
if we get more users, we need to update only the helper (possibly
reserving an additional IFF bit).
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e86663c475 ]
Nothing is decrementing the index "i" while we are cleaning up the
fragments we could not successful transmit.
Fixes: 9cde94506e ("bgmac: implement scatter/gather support")
Reported-by: coverity (CID 1352048)
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 005db31d5f ]
Commit e826eafa65 ("bonding: Call netif_carrier_off after
register_netdevice") moved netif_carrier_off() from bond_init() to
bond_create(), but the latter is called only for initial default
devices and ones created through sysfs:
$ modprobe bonding
$ echo +bond1 > /sys/class/net/bonding_masters
$ ip link add bond2 type bond
$ grep "MII Status" /proc/net/bonding/*
/proc/net/bonding/bond0:MII Status: down
/proc/net/bonding/bond1:MII Status: down
/proc/net/bonding/bond2:MII Status: up
Ensure that carrier is initially off also for devices created through
netlink.
Signed-off-by: Beniamino Galvani <bgalvani@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 083ae30828 ]
The per-socket rate limit for 'challenge acks' was introduced in the
context of limiting ack loops:
commit f2b2c582e8 ("tcp: mitigate ACK loops for connections as tcp_sock")
And I think it can be extended to rate limit all 'challenge acks' on a
per-socket basis.
Since we have the global tcp_challenge_ack_limit, this patch allows for
tcp_challenge_ack_limit to be set to a large value and effectively rely on
the per-socket limit, or set tcp_challenge_ack_limit to a lower value and
still prevents a single connections from consuming the entire challenge ack
quota.
It further moves in the direction of eliminating the global limit at some
point, as Eric Dumazet has suggested. This a follow-up to:
Subject: tcp: make challenge acks less predictable
Cc: Eric Dumazet <edumazet@google.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Yue Cao <ycao009@ucr.edu>
Signed-off-by: Jason Baron <jbaron@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 75ff39ccc1 ]
Yue Cao claims that current host rate limiting of challenge ACKS
(RFC 5961) could leak enough information to allow a patient attacker
to hijack TCP sessions. He will soon provide details in an academic
paper.
This patch increases the default limit from 100 to 1000, and adds
some randomization so that the attacker can no longer hijack
sessions without spending a considerable amount of probes.
Based on initial analysis and patch from Linus.
Note that we also have per socket rate limiting, so it is tempting
to remove the host limit in the future.
v2: randomize the count of challenge acks per second, not the period.
Fixes: 282f23c6ee ("tcp: implement RFC 5961 3.2")
Reported-by: Yue Cao <ycao009@ucr.edu>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 205e1e255c ]
Matt reported that we have a NULL pointer dereference
in ppp_pernet() from ppp_connect_channel(),
i.e. pch->chan_net is NULL.
This is due to that a parallel ppp_unregister_channel()
could happen while we are in ppp_connect_channel(), during
which pch->chan_net set to NULL. Since we need a reference
to net per channel, it makes sense to sync the refcnt
with the life time of the channel, therefore we should
release this reference when we destroy it.
Fixes: 1f461dcdd2 ("ppp: take reference on channels netns")
Reported-by: Matt Bennett <Matt.Bennett@alliedtelesis.co.nz>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linux-ppp@vger.kernel.org
Cc: Guillaume Nault <g.nault@alphalink.fr>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ee6667cd8 upstream.
The updated ndctl unit tests discovered that if a pfn configuration with
a 4K alignment is read from the namespace, that alignment will be
ignored in favor of the default 2M alignment. The result is that the
configuration will fail initialization with a message like:
dax6.1: bad offset: 0x22000 dax disabled align: 0x200000
Fix this by allowing the alignment read from the info block to override
the default which is 2M not 0 in the autodetect path. This also fixes a
similar problem with the mode and alignment settings silently being
overwritten by the kernel when userspace has changed it. We now will
either overwrite the info block if userspace changes the uuid or fail
and warn if a live setting disagrees with the info block.
Cc: Micah Parrish <micah.parrish@hpe.com>
Cc: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45a0dac045 upstream.
We want to use the alignment as the allocation and mapping unit.
Previously this information was only useful for establishing the data
offset, but now it is important to remember the granularity for the
later use.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a60ae81e5e upstream.
Fix mips_cm_max_vp_width for UP kernels where it previously referenced
smp_num_siblings, which is not declared for UP kernels. This led to
build errors such as the following:
drivers/built-in.o: In function `$L446':
irq-mips-gic.c:(.text+0x1994): undefined reference to `smp_num_siblings'
drivers/built-in.o:irq-mips-gic.c:(.text+0x199c): more undefined references to `smp_num_siblings' follow
On UP kernels simply return 1, leaving the reference to smp_num_siblings
in place only for SMP kernels.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12332/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1892c3776 upstream.
file_remove_privs() is called with inode lock on file_inode(), which
proceeds to calling notify_change() on file->f_path.dentry. Which triggers
the WARN_ON_ONCE(!inode_is_locked(inode)) in addition to deadlocking later
when ovl_setattr tries to lock the underlying inode again.
Fix this mess by not mixing the layers, but doing everything on underlying
dentry/inode.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Fixes: 07a2daab49 ("ovl: Copy up underlying inode's ->i_mode to overlay inode")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 10eec60ce7 upstream.
This prevents a double-fetch from user space that can lead to to an
undersized allocation and heap overflow.
Fixes: 54dbc15172 ("vfs: hoist the btrfs deduplication ioctl to the vfs")
Signed-off-by: Scott Bauer <sbauer@plzdonthack.me>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a36aa80f3c upstream.
Driver initialization tries to request a hub (GTH) driver module from
its probe callback, resulting in a deadlock.
This patch solves the problem by adding a deferred work for requesting
the hub module.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 06708f8152 upstream.
Commit aebea2ba0f ("net: mvneta: fix Tx interrupt delay") intended to
set coalescing threshold to a value guaranteeing interrupt generation
per each sent packet, so that buffers can be released with no delay.
In fact setting threshold to '1' was wrong, because it causes interrupt
every two packets. According to the documentation a reason behind it is
following - interrupt occurs once sent buffers counter reaches a value,
which is higher than one specified in MVNETA_TXQ_SIZE_REG(q). This
behavior was confirmed during tests. Also when testing the SoC working
as a NAS device, better performance was observed with int-per-packet,
as it strongly depends on the fact that all transmitted packets are
released immediately.
This commit enables NETA controller work in interrupt per sent packet mode
by setting coalescing threshold to 0.
Signed-off-by: Dmitri Epshtein <dima@marvell.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Fixes aebea2ba0f ("net: mvneta: fix Tx interrupt delay")
Acked-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 930c532869 upstream.
Currently, osd_weight and osd_state fields are updated in the encoding
order. This is wrong, because an incremental map may look like e.g.
new_up_client: { osd=6, addr=... } # set osd_state and addr
new_state: { osd=6, xorstate=EXISTS } # clear osd_state
Suppose osd6's current osd_state is EXISTS (i.e. osd6 is down). After
applying new_up_client, osd_state is changed to EXISTS | UP. Carrying
on with the new_state update, we flip EXISTS and leave osd6 in a weird
"!EXISTS but UP" state. A non-existent OSD is considered down by the
mapping code
2087 for (i = 0; i < pg->pg_temp.len; i++) {
2088 if (ceph_osd_is_down(osdmap, pg->pg_temp.osds[i])) {
2089 if (ceph_can_shift_osds(pi))
2090 continue;
2091
2092 temp->osds[temp->size++] = CRUSH_ITEM_NONE;
and so requests get directed to the second OSD in the set instead of
the first, resulting in OSD-side errors like:
[WRN] : client.4239 192.168.122.21:0/2444980242 misdirected client.4239.1:2827 pg 2.5df899f2 to osd.4 not [1,4,6] in e680/680
and hung rbds on the client:
[ 493.566367] rbd: rbd0: write 400000 at 11cc00000 (0)
[ 493.566805] rbd: rbd0: result -6 xferred 400000
[ 493.567011] blk_update_request: I/O error, dev rbd0, sector 9330688
The fix is to decouple application from the decoding and:
- apply new_weight first
- apply new_state before new_up_client
- twiddle osd_state flags if marking in
- clear out some of the state if osd is destroyed
Fixes: http://tracker.ceph.com/issues/14901
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Josh Durgin <jdurgin@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d4f56c7773 upstream.
index gets incremented during check to determine if the
messages can be transferred with dma. But not reset after
that, resulting in wrong start value in subsequent loop,
causing failure. Fix it.
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6519c3d7b8 upstream.
The dv_timings_cap() and enum_dv_timings() pad operations take a pad
number as an input argument and return the DV timings capabilities and
list of supported DV timings for that pad.
Commit bd3e275f3e ("[media] media: i2c: adv7604: Use v4l2-dv-timings
helpers") broke this as it started ignoring the pad number, always
returning the information associated with the currently selected input.
Fix it.
Fixes: bd3e275f3e ("[media] media: i2c: adv7604: Use v4l2-dv-timings helpers")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c13ce8f6b upstream.
Variable "now" seems to be genuinely used unintialized
if branch
if (CPUCLOCK_PERTHREAD(timer->it_clock)) {
is not taken and branch
if (unlikely(sighand == NULL)) {
is taken. In this case the process has been reaped and the timer is marked as
disarmed anyway. So none of the postprocessing of the sample is
required. Return right away.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Link: http://lkml.kernel.org/r/20160707223911.GA26483@p183.telecom.by
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aa93d1fee8 upstream.
Fix a memory leak on probe error of the airspy usb device driver.
The problem is triggered when more than 64 usb devices register with
v4l2 of type VFL_TYPE_SDR or VFL_TYPE_SUBDEV.
The memory leak is caused by the probe function of the airspy driver
mishandeling errors and not freeing the corresponding control structures
when an error occours registering the device to v4l2 core.
A badusb device can emulate 64 of these devices, and then through
continual emulated connect/disconnect of the 65th device, cause the
kernel to run out of RAM and crash the kernel, thus causing a local DOS
vulnerability.
Fixes CVE-2016-5400
Signed-off-by: James Patrick-Evans <james@jmp-e.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e7ff2ca7f upstream.
Commit b704f70ce2 ("SCSI: fix bug in scsi_dev_info_list matching")
changed the way vendor- and model-string matching was carried out in the
routine that looks up entries in a SCSI devinfo list. The new matching
code failed to take into account the case of a maximum-length string; in
such cases it could end up testing for a terminating '\0' byte beyond
the end of the memory allocated to the string. This out-of-bounds bug
was detected by UBSAN.
I don't know if anybody has actually encountered this bug. The symptom
would be that a device entry in the blacklist might not be matched
properly if it contained an 8-character vendor name or a 16-character
model name. Such entries certainly exist in scsi_static_device_list.
This patch fixes the problem by adding a check for a maximum-length
string before the '\0' test.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: b704f70ce2 ("SCSI: fix bug in scsi_dev_info_list matching")
Tested-by: Wilfried Klaebe <linux-kernel@lebenslange-mailadresse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 99ec8a3608 upstream.
When mapping an interrupt to a VP(E) we must use the identifier for the
VP that the hardware expects, and this does not always match up with the
Linux CPU number. Commit d46812bb0b ("irqchip: mips-gic: Use HW IDs
for VPE_OTHER_ADDR") corrected this for the cases that existed at the
time it was written, but commit 2af70a9620 ("irqchip/mips-gic: Add a
IPI hierarchy domain") added another case before the former patch was
merged. This leads to incorrectly using Linux CPU numbers when mapping
interrupts to VPs, which breaks on certain systems such as those with
multi-core I6400 CPUs. Fix by adding the appropriate call to
mips_cm_vp_id() to retrieve the expected VP identifier.
Fixes: d46812bb0b ("irqchip: mips-gic: Use HW IDs for VPE_OTHER_ADDR")
Fixes: 2af70a9620 ("irqchip/mips-gic: Add a IPI hierarchy domain")
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Qais Yousef <qsyousef@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Link: http://lkml.kernel.org/r/20160705132600.27730-1-paul.burton@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 25e1ed6e64 upstream.
For 'real' hardware CAN devices the netlink interface is used to set CAN
specific communication parameters. Real CAN hardware can not be created nor
removed with the ip tool ...
This patch adds a private dellink function for the CAN device driver interface
that does just nothing.
It's a follow up to commit 993e6f2fd ("can: fix oops caused by wrong rtnl
newlink usage") but for dellink.
Reported-by: ajneu <ajneu1@gmail.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bce271f255 upstream.
With upstream commit bb208f144c (can: fix handling of unmodifiable
configuration options) a new can_validate() function was introduced.
When invoking 'ip link set can0 type can' without any configuration data
can_validate() tries to validate the content without taking into account that
there's totally no content. This patch adds a check for missing content.
Reported-by: ajneu <ajneu1@gmail.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 427460c83c upstream.
When testing CAN write floods on Altera's CycloneV, the first 2 bytes
are sometimes 0x00, 0x00 or corrupted instead of the values sent. Also
observed bytes 4 & 5 were corrupted in some cases.
The D_CAN Data registers are 32 bits and changing from 16 bit writes to
32 bit writes fixes the problem.
Testing performed on Altera CycloneV (D_CAN). Requesting tests on other
C_CAN & D_CAN platforms.
Reported-by: Richard Andrysek <richard.andrysek@gomtec.de>
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 43200a4480 upstream.
At high bus load it could happen that "at91_poll()" enters with all RX
message boxes filled up. If then at the end the "quota" is exceeded as
well, "rx_next" will not be reset to the first RX mailbox and hence the
interrupts remain disabled.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Tested-by: Amr Bekhit <amrbekhit@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7dd4912594 upstream.
Starting with the following commit:
fde7d22e01 ("sched/fair: Fix overly small weight for interactive group entities")
calc_tg_weight() doesn't compute the right value as expected by effective_load().
The difference is in the 'correction' term. In order to ensure \Sum
rw_j >= rw_i we cannot use tg->load_avg directly, since that might be
lagging a correction on the current cfs_rq->avg.load_avg value.
Therefore we use tg->load_avg - cfs_rq->tg_load_avg_contrib +
cfs_rq->avg.load_avg.
Now, per the referenced commit, calc_tg_weight() doesn't use
cfs_rq->avg.load_avg, as is later used in @w, but uses
cfs_rq->load.weight instead.
So stop using calc_tg_weight() and do it explicitly.
The effects of this bug are wake_affine() making randomly
poor choices in cgroup-intense workloads.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: fde7d22e01 ("sched/fair: Fix overly small weight for interactive group entities")
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f68381a70b upstream.
The code that fills packed command header assumes that CPU runs in
little-endian mode. Hence the header is malformed in big-endian mode
and causes MMC data transfer errors:
[ 563.200828] mmcblk0: error -110 transferring data, sector 2048, nr 8, cmd response 0x900, card status 0xc40
[ 563.219647] mmcblk0: packed cmd failed, nr 2, sectors 16, failure index: -1
Convert header data to LE.
Signed-off-by: Taras Kondratiuk <takondra@cisco.com>
Fixes: ce39f9d17c ("mmc: support packed write command for eMMC4.5 devices")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bfe5b1b1e0 upstream.
Set 'idata->buf' to NULL so that it never gets returned without
initialization. This fixes a bug where mmc_blk_ioctl_cmd() would
free both 'idata' and 'idata->buf' but 'idata->buf' was returned
uninitialized.
Fixes: 1ff8950c04 ("mmc: block: change to use kmalloc when copy data from userspace")
Signed-off-by: Ville Viinikka <ville@tuxera.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 076501ff6b upstream.
The "expert" menu was broken (split) such that all entries in it after
KALLSYMS were displayed in the "General setup" area instead of in the
"Expert users" area. Fix this by adding one kconfig dependency.
Yes, the Expert users menu is fragile. Problems like this have happened
several times in the past. I will attempt to isolate the Expert users
menu if there is interest in that.
Fixes: 4d5d5664c9 ("x86: kallsyms: disable absolute percpu symbols on !SMP")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7831b4ff0d upstream.
A qeth_card contains a napi_struct linked to the net_device during
device probing. This struct must be deleted when removing the qeth
device, otherwise Panic on oops can occur when qeth devices are
repeatedly removed and added.
Fixes: a1c3ed4c9c ("qeth: NAPI support for l2 and l3 discipline")
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Tested-by: Alexander Klein <ALKL@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 096cdc6f52 upstream.
We verify "u_cmd.outsize" and "u_cmd.insize" but we need to make sure
that those values have not changed between the two copy_from_user()
calls. Otherwise it could lead to a buffer overflow.
Additionally, cros_ec_cmd_xfer() can set s_cmd->insize to a lower value.
We should use the new smaller value so we don't copy too much data to
the user.
Reported-by: Pengfei Wang <wpengfeinudt@gmail.com>
Fixes: a841178445 ('mfd: cros_ec: Use a zero-length array for command data')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cb7d224f82 upstream.
If the lockd service fails to start up then we need to be sure that the
notifier blocks are not registered, otherwise a subsequent start of the
service could cause the same notifier to be registered twice, leading to
soft lockups.
Signed-off-by: Scott Mayhew <smayhew@redhat.com>
Fixes: 0751ddf77b "lockd: Register callbacks on the inetaddr_chain..."
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 595144c114 upstream.
The flags element of clk_init_data was never initialized for mmc-
phase-clocks resulting in the element containing a random value
and thus possibly enabling unwanted clock flags.
Fixes: 89bf26cbc1 ("clk: rockchip: Add support for the mmc clock phases using the framework")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 719bd65420 upstream.
The trasfer timeout is fixed at 1000 ms. Reading a 4Mbyte flash over
1MHz SPI bus takes way longer than that. Calculate the timeout from the
actual time the transfer is supposed to take and multiply by 2 for good
measure.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4dc0dd8360 upstream.
When using DMA, the transfer_one callback should return 1 because the
transfer hasn't finished yet.
A previous commit changed the function to return 0 when the DMA channels
were correctly prepared.
This manifested in Veyron boards with this message:
[ 1.983605] cros-ec-spi spi0.0: EC failed to respond in time
Fixes: ea98491133 ("spi: rockchip: check return value of dmaengine_prep_slave_sg")
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e06b933e6d upstream.
- m_start() in fs/namespace.c expects that ns->event is incremented each
time a mount added or removed from ns->list.
- umount_tree() removes items from the list but does not increment event
counter, expecting that it's done before the function is called.
- There are some codepaths that call umount_tree() without updating
"event" counter. e.g. from __detach_mounts().
- When this happens m_start may reuse a cached mount structure that no
longer belongs to ns->list (i.e. use after free which usually leads
to infinite loop).
This change fixes the above problem by incrementing global event counter
before invoking umount_tree().
Change-Id: I622c8e84dcb9fb63542372c5dbf0178ee86bb589
Signed-off-by: Andrey Ulanov <andreyu@google.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 742c87bf27 upstream.
CPU notifications from the firmware coming in when cpufreq is
suspended cause cpufreq_update_current_freq() to return 0 which
triggers the WARN_ON() in cpufreq_update_policy() for no reason.
Avoid that by checking cpufreq_suspended before calling
cpufreq_update_current_freq().
Fixes: c9d9c929e6 (cpufreq: Abort cpufreq_update_current_freq() for cpufreq_suspended set)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b403f0e37a upstream.
v9fs may be used as lower layer of overlayfs and accessing f_path.dentry
can lead to a crash. In this case it's a NULL pointer dereference in
p9_fid_create().
Fix by replacing direct access of file->f_path.dentry with the
file_dentry() accessor, which will always return a native object.
Reported-by: Alessio Igor Bogani <alessioigorbogani@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Tested-by: Alessio Igor Bogani <alessioigorbogani@gmail.com>
Fixes: 4bacc9c923 ("overlayfs: Make f_path always point to the overlay and f_inode to the underlay")
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7bc9491645 upstream.
Although the extent tree depth of 5 should enough be for the worst
case of 2*32 extents of length 1, the extent tree code does not
currently to merge nodes which are less than half-full with a sibling
node, or to shrink the tree depth if possible. So it's possible, at
least in theory, for the tree depth to be greater than 5. However,
even in the worst case, a tree depth of 32 is highly unlikely, and if
the file system is maliciously corrupted, an insanely large eh_depth
can cause memory allocation failures that will trigger kernel warnings
(here, eh_depth = 65280):
JBD2: ext4.exe wants too many credits credits:195849 rsv_credits:0 max:256
------------[ cut here ]------------
WARNING: CPU: 0 PID: 50 at fs/jbd2/transaction.c:293 start_this_handle+0x569/0x580
CPU: 0 PID: 50 Comm: ext4.exe Not tainted 4.7.0-rc5+ #508
Stack:
604a8947 625badd8 0002fd09 00000000
60078643 00000000 62623910 601bf9bc
62623970 6002fc84 626239b0 900000125
Call Trace:
[<6001c2dc>] show_stack+0xdc/0x1a0
[<601bf9bc>] dump_stack+0x2a/0x2e
[<6002fc84>] __warn+0x114/0x140
[<6002fdff>] warn_slowpath_null+0x1f/0x30
[<60165829>] start_this_handle+0x569/0x580
[<60165d4e>] jbd2__journal_start+0x11e/0x220
[<60146690>] __ext4_journal_start_sb+0x60/0xa0
[<60120a81>] ext4_truncate+0x131/0x3a0
[<60123677>] ext4_setattr+0x757/0x840
[<600d5d0f>] notify_change+0x16f/0x2a0
[<600b2b16>] do_truncate+0x76/0xc0
[<600c3e56>] path_openat+0x806/0x1300
[<600c55c9>] do_filp_open+0x89/0xf0
[<600b4074>] do_sys_open+0x134/0x1e0
[<600b4140>] SyS_open+0x20/0x30
[<6001ea68>] handle_syscall+0x88/0x90
[<600295fd>] userspace+0x3fd/0x500
[<6001ac55>] fork_handler+0x85/0x90
---[ end trace 08b0b88b6387a244 ]---
[ Commit message modified and the extent tree depath check changed
from 5 to 32 -- tytso ]
Cc: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f0fe970df3 upstream.
There are legitimate reasons to disallow mmap on certain files, notably
in sysfs or procfs. We shouldn't emulate mmap support on file systems
that don't offer support natively.
CVE-2016-1583
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
[tyhicks: clean up f_op check by using ecryptfs_file_to_lower()]
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 78c4e17241 upstream.
This reverts commit 2f36db7100.
It fixed a local root exploit but also introduced a dependency on
the lower file system implementing an mmap operation just to open a file,
which is a bit of a heavy hammer. The right fix is to have mmap depend
on the existence of the mmap handler instead.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6343a21208 upstream.
(Another one for the f_path debacle.)
ltp fcntl33 testcase caused an Oops in selinux_file_send_sigiotask.
The reason is that generic_add_lease() used filp->f_path.dentry->inode
while all the others use file_inode(). This makes a difference for files
opened on overlayfs since the former will point to the overlay inode the
latter to the underlying inode.
So generic_add_lease() added the lease to the overlay inode and
generic_delete_lease() removed it from the underlying inode. When the file
was released the lease remained on the overlay inode's lock list, resulting
in use after free.
Reported-by: Eryu Guan <eguan@redhat.com>
Fixes: 4bacc9c923 ("overlayfs: Make f_path always point to the overlay and f_inode to the underlay")
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5bc28b93a3 upstream.
Change power_supply_read_temp() to use power_supply_get_property()
so that it will check the use_cnt and ensure it is > 0. The use_cnt
will be incremented at the end of __power_supply_register, so this
will block to case where get_property can be called before the supply
is fully registered. This fixes the issue show in the stack below:
[ 1.452598] power_supply_read_temp+0x78/0x80
[ 1.458680] thermal_zone_get_temp+0x5c/0x11c
[ 1.464765] thermal_zone_device_update+0x34/0xb4
[ 1.471195] thermal_zone_device_register+0x87c/0x8cc
[ 1.477974] __power_supply_register+0x364/0x424
[ 1.484317] power_supply_register_no_ws+0x10/0x18
[ 1.490833] bq27xxx_battery_setup+0x10c/0x164
[ 1.497003] bq27xxx_battery_i2c_probe+0xd0/0x1b0
[ 1.503435] i2c_device_probe+0x174/0x240
[ 1.509172] driver_probe_device+0x1fc/0x29c
[ 1.515167] __driver_attach+0xa4/0xa8
[ 1.520643] bus_for_each_dev+0x58/0x98
[ 1.526204] driver_attach+0x20/0x28
[ 1.531505] bus_add_driver+0x1c8/0x22c
[ 1.537067] driver_register+0x68/0x108
[ 1.542630] i2c_register_driver+0x38/0x7c
[ 1.548457] bq27xxx_battery_i2c_driver_init+0x18/0x20
[ 1.555321] do_one_initcall+0x38/0x12c
[ 1.560886] kernel_init_freeable+0x148/0x1ec
[ 1.566972] kernel_init+0x10/0xfc
[ 1.572101] ret_from_fork+0x10/0x40
Also make the same change to ps_get_max_charge_cntl_limit() and
ps_get_cur_chrage_cntl_limit() to be safe. Lastly, change the return
value of power_supply_get_property() to -EAGAIN from -ENODEV if
use_cnt <= 0.
Fixes: 297d716f62 ("power_supply: Change ownership from driver to core")
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8fa3b8d689 upstream.
If percpu_ref initialization fails during css_create(), the free path
can end up trying to free css->id of zero. As ID 0 is unused, it
doesn't cause a critical breakage but it does trigger a warning
message. Fix it by setting css->id to -1 from init_and_link_css().
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Wenwei Tao <ww.tao0320@gmail.com>
Fixes: 01e586598b ("cgroup: release css->id after css_free")
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b00c52dae6 upstream.
When create css failed, before call css_free_rcu_fn, we remove the css
id and exit the percpu_ref, but we will do these again in
css_free_work_fn, so they are redundant. Especially the css id, that
would cause problem if we remove it twice, since it may be assigned to
another css after the first remove.
tj: This was broken by two commits updating the free path without
synchronizing the creation failure path. This can be easily
triggered by trying to create more than 64k memory cgroups.
Signed-off-by: Wenwei Tao <ww.tao0320@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Vladimir Davydov <vdavydov@parallels.com>
Fixes: 9a1049da9b ("percpu-refcount: require percpu_ref to be exited explicitly")
Fixes: 01e586598b ("cgroup: release css->id after css_free")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ba562d5e54 upstream.
Some PINs do not have a MUX register, it is not an error.
It is necessary to allow the continuation of the PINs configuration,
otherwise the whole PIN-group will be configured incorrectly.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0ac3c0a402 upstream.
With many repeated suspend resume cycles, the pin specific wakeirq
may not always work on omaps. This is because the write to enable the
pin interrupt may not have reached the device over the interconnect
before suspend happens.
Let's fix the issue with a flush of posted write with a readback.
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 749d088b8e upstream.
Protocol for the "version" fields is: hypervisor raises it (making it
uneven) before it starts updating the fields and raises it again (making
it even) when it is done. Thus the guest can make sure the time values
it got are consistent by checking the version before and after reading
them.
Add CPU barries after getting version value just like what function
vread_pvclock does, because all of callees in this function is inline.
Fixes: 502dfeff23
Signed-off-by: Minfei Huang <mnghuan@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9003c9cfa upstream.
Passes input_id struct to the common probe function for the tsc200x drivers
instead of just the bustype.
This allows for the use of the product variable to set the input_dev->name
variable according to the type of touchscreen used. Note that when we
introduced support for TSC2004 we started calling everything TSC200X, so
let's keep this quirk.
Signed-off-by: Michael Welling <mwelling@ieee.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e4add7b6be upstream.
According to the RMI4 spec the maximum size of F12 control register 8 is
15 bytes. The current code incorrectly reports an error if control 8 is
greater then 14. Making sensors with a control register 8 with 15 bytes
unusable.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reported-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3e9161bfe0 upstream.
This reverts commit 5f7e5445a2 because
removal of input_mt_report_slot_state() means we no longer generate
tracking IDs for the reported contacts.
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Acked-by: Ping Cheng <pinglinux@gmail.com>
commit c7f1429389 upstream.
Xbox One controllers have multiple interfaces which all have the
same class, subclass, and protocol. One of the these interfaces
has only a single endpoint. When Xpad attempts to bind to this
interface, it causes an oops when trying initialize the output URB
by trying to access the second endpoint's descriptor.
This situation was avoided for known Xbox One devices by checking
the XTYPE constant associated with the VID and PID tuple. However,
this breaks when new or previously unknown Xbox One controllers
are attached to the system.
This change addresses the problem by deriving the XTYPE for Xbox
One controllers based on the interface protocol before checking
the interface number.
Fixes: 1a48ff81b3 ("Input: xpad - add support for Xbox One controllers")
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 60842ef812 upstream.
The VMWare EFI BIOS will expose port 0x5658 as an ACPI resource. This
causes the port to be reserved by the APCI module as the system comes up,
making it unavailable to be reserved again by other drivers, thus
preserving this VMWare port for special use in a VMWare guest.
This port is designed to be shared among multiple VMWare services, such as
the VMMOUSE. Because of this, VMMOUSE should not try to reserve this port
on its own.
The VMWare non-EFI BIOS does not do this to preserve compatibility with
existing/legacy VMs. It is known that there is small chance a VM may be
configured such that these ports get reserved by other non-VMWare devices,
and if this ever happens, the result is undefined.
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e4ec8cc803 upstream.
The stack object “r1” has a total size of 32 bytes. Its field
“event” and “val” both contain 4 bytes padding. These 8 bytes
padding bytes are sent to user without being initialized.
Signed-off-by: Kangjie Lu <kjlu@gatech.edu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a47e9cff9 upstream.
The stack object “r1” has a total size of 32 bytes. Its field
“event” and “val” both contain 4 bytes padding. These 8 bytes
padding bytes are sent to user without being initialized.
Signed-off-by: Kangjie Lu <kjlu@gatech.edu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cec8f96e49 upstream.
The stack object “tread” has a total size of 32 bytes. Its field
“event” and “val” both contain 4 bytes padding. These 8 bytes
padding bytes are sent to user without being initialized.
Signed-off-by: Kangjie Lu <kjlu@gatech.edu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit efd1535270 upstream.
Sometimes blkfront may twice receive blkback_changed() notification
(XenbusStateConnected) after migration, which will cause
talk_to_blkback() to be called twice too and confuse xen-blkback.
The flow is as follow:
blkfront blkback
blkfront_resume()
> talk_to_blkback()
> Set blkfront to XenbusStateInitialised
front changed()
> Connect()
> Set blkback to XenbusStateConnected
blkback_changed()
> Skip talk_to_blkback()
because frontstate == XenbusStateInitialised
> blkfront_connect()
> Set blkfront to XenbusStateConnected
-----
And here we get another XenbusStateConnected notification leading
to:
-----
blkback_changed()
> because now frontstate != XenbusStateInitialised
talk_to_blkback() is also called again
> blkfront state changed from
XenbusStateConnected to XenbusStateInitialised
(Which is not correct!)
front_changed():
> Do nothing because blkback
already in XenbusStateConnected
Now blkback is in XenbusStateConnected but blkfront is still
in XenbusStateInitialised - leading to no disks.
Poking of the XenbusStateConnected state is allowed (to deal with
block disk change) and has to be dealt with. The most likely
cause of this bug are custom udev scripts hooking up the disks
and then validating the size.
Signed-off-by: Bob Liu <bob.liu@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a6f71ad99 upstream.
After a migrate to another host (which may not have multiqueue
support), the number of rings (block hardware queues)
may be changed and the ring info structure will also be reallocated.
This patch fixes two related bugs:
* call blk_mq_update_nr_hw_queues() to make blk-core know the number
of hardware queues have been changed.
* Don't store rinfo pointer to hctx->driver_data, because rinfo may be
reallocated so use hctx->queue_num to get the rinfo structure instead.
Signed-off-by: Bob Liu <bob.liu@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7469be95a4 upstream.
xenbus_dev_request_and_reply() needs to track whether a transaction is
open. For XS_TRANSACTION_START messages it calls transaction_start()
and for XS_TRANSACTION_END messages it calls transaction_end().
If sending an XS_TRANSACTION_START message fails or responds with an
an error, the transaction is not open and transaction_end() must be
called.
If sending an XS_TRANSACTION_END message fails, the transaction is
still open, but if an error response is returned the transaction is
closed.
Commit 027bd7e899 ("xen/xenbus: Avoid synchronous wait on XenBus
stalling shutdown/restart") introduced a regression where failed
XS_TRANSACTION_START messages were leaving the transaction open. This
can cause problems with suspend (and migration) as all transactions
must be closed before suspending.
It appears that the problematic change was added accidentally, so just
remove it.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0beef634b8 upstream.
Inability to locate a user mode specified transaction ID should not
lead to a kernel crash. For other than XS_TRANSACTION_START also
don't issue anything to xenbus if the specified ID doesn't match that
of any active transaction.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b427a5953 upstream.
Uncompleted reqs used to be 'saved and resubmitted' in blkfront_recover() during
migration, but that's too late after multi-queue was introduced.
After a migrate to another host (which may not have multiqueue support), the
number of rings (block hardware queues) may be changed and the ring and shadow
structure will also be reallocated.
The blkfront_recover() then can't 'save and resubmit' the real
uncompleted reqs because shadow structure have been reallocated.
This patch fixes this issue by moving the 'save' logic out of
blkfront_recover() to earlier place in blkfront_resume().
The 'resubmit' is not changed and still in blkfront_recover().
Signed-off-by: Bob Liu <bob.liu@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 02ef871eca upstream.
Current overlap check is evaluating to false a case where a filter
field is fully contained (proper subset) of a r/w request. This
change applies classical overlap check instead to include all the
scenarios.
More specifically, for (Hilscher GmbH CIFX 50E-DP(M/S)) device driver
the logic is such that the entire confspace is read and written in 4
byte chunks. In this case as an example, CACHE_LINE_SIZE,
LATENCY_TIMER and PCI_BIST are arriving together in one call to
xen_pcibk_config_write() with offset == 0xc and size == 4. With the
exsisting overlap check the LATENCY_TIMER field (offset == 0xd, length
== 1) is fully contained in the write request and hence is excluded
from write, which is incorrect.
Signed-off-by: Andrey Grodzovsky <andrey2805@gmail.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Jan Beulich <JBeulich@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f52e126cc7 upstream.
With recent binutils update to support dwarf CFI pseudo-ops in gas, we
now get .eh_frame vs. .debug_frame. Although the call frame info is
exactly the same in both, the CIE differs, which the current kernel
unwinder can't cope with.
This broke both the kernel unwinder as well as loadable modules (latter
because of a new unhandled relo R_ARC_32_PCREL from .rela.eh_frame in
the module loader)
The ideal solution would be to switch unwinder to .eh_frame.
For now however we can make do by just ensureing .debug_frame is
generated by removing -fasynchronous-unwind-tables
.eh_frame generated with -gdwarf-2 -fasynchronous-unwind-tables
.debug_frame generated with -gdwarf-2
Fixes STAR 9001058196
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9bd54517ee upstream.
If CONFIG_ARC_DW2_UNWIND is disabled every time arc_unwind_core()
gets called following message gets printed in debug console:
----------------->8---------------
CONFIG_ARC_DW2_UNWIND needs to be enabled
----------------->8---------------
That message makes sense if user indeed wants to see a backtrace or
get nice function call-graphs in perf but what if user disabled
unwinder for the purpose? Why pollute his debug console?
So instead we'll warn user about possibly missing feature once and
let him decide if that was what he or she really wanted.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 57675cb976 upstream.
Lengthy output of sysrq-w may take a lot of time on slow serial console.
Currently we reset NMI-watchdog on the current CPU to avoid spurious
lockup messages. Sometimes this doesn't work since softlockup watchdog
might trigger on another CPU which is waiting for an IPI to proceed.
We reset softlockup watchdogs on all CPUs, but we do this only after
listing all tasks, and this may be too late on a busy system.
So, reset watchdogs CPUs earlier, in for_each_process_thread() loop.
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1465474805-14641-1-git-send-email-aryabinin@virtuozzo.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 368301f2fe upstream.
With this command sequence:
modprobe plip
modprobe pps_parport
rmmod pps_parport
the partport_pps modules causes this crash:
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: parport_detach+0x1d/0x60 [pps_parport]
Oops: 0000 [#1] SMP
...
Call Trace:
parport_unregister_driver+0x65/0xc0 [parport]
SyS_delete_module+0x187/0x210
The sequence that builds up to this is:
1) plip is loaded and takes the parport device for exclusive use:
plip0: Parallel port at 0x378, using IRQ 7.
2) pps_parport then fails to grab the device:
pps_parport: parallel port PPS client
parport0: cannot grant exclusive access for device pps_parport
pps_parport: couldn't register with parport0
3) rmmod of pps_parport is then killed because it tries to access
pardev->name, but pardev (taken from port->cad) is NULL.
So add a check for NULL in the test there too.
Link: http://lkml.kernel.org/r/20160714115245.12651-1-jslaby@suse.cz
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Rodolfo Giometti <giometti@enneenne.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 73f576c04b upstream.
The memory controller has quite a bit of state that usually outlives the
cgroup and pins its CSS until said state disappears. At the same time
it imposes a 16-bit limit on the CSS ID space to economically store IDs
in the wild. Consequently, when we use cgroups to contain frequent but
small and short-lived jobs that leave behind some page cache, we quickly
run into the 64k limitations of outstanding CSSs. Creating a new cgroup
fails with -ENOSPC while there are only a few, or even no user-visible
cgroups in existence.
Although pinning CSSs past cgroup removal is common, there are only two
instances that actually need an ID after a cgroup is deleted: cache
shadow entries and swapout records.
Cache shadow entries reference the ID weakly and can deal with the CSS
having disappeared when it's looked up later. They pose no hurdle.
Swap-out records do need to pin the css to hierarchically attribute
swapins after the cgroup has been deleted; though the only pages that
remain swapped out after offlining are tmpfs/shmem pages. And those
references are under the user's control, so they are manageable.
This patch introduces a private 16-bit memcg ID and switches swap and
cache shadow entries over to using that. This ID can then be recycled
after offlining when the CSS remains pinned only by objects that don't
specifically need it.
This script demonstrates the problem by faulting one cache page in a new
cgroup and deleting it again:
set -e
mkdir -p pages
for x in `seq 128000`; do
[ $((x % 1000)) -eq 0 ] && echo $x
mkdir /cgroup/foo
echo $$ >/cgroup/foo/cgroup.procs
echo trex >pages/$x
echo $$ >/cgroup/cgroup.procs
rmdir /cgroup/foo
done
When run on an unpatched kernel, we eventually run out of possible IDs
even though there are no visible cgroups:
[root@ham ~]# ./cssidstress.sh
[...]
65000
mkdir: cannot create directory '/cgroup/foo': No space left on device
After this patch, the IDs get released upon cgroup destruction and the
cache and css objects get released once memory reclaim kicks in.
[hannes@cmpxchg.org: init the IDR]
Link: http://lkml.kernel.org/r/20160621154601.GA22431@cmpxchg.org
Fixes: b2052564e6 ("mm: memcontrol: continue cache reclaim from offlined groups")
Link: http://lkml.kernel.org/r/20160617162516.GD19084@cmpxchg.org
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reported-by: John Garcia <john.garcia@mesosphere.io>
Reviewed-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Nikolay Borisov <kernel@kyup.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5a49973d71 upstream.
The VM_BUG_ON_PAGE in page_move_anon_rmap() is more trouble than it's
worth: the syzkaller fuzzer hit it again. It's still wrong for some THP
cases, because linear_page_index() was never intended to apply to
addresses before the start of a vma.
That's easily fixed with a signed long cast inside linear_page_index();
and Dmitry has tested such a patch, to verify the false positive. But
why extend linear_page_index() just for this case? when the avoidance in
page_move_anon_rmap() has already grown ugly, and there's no reason for
the check at all (nothing else there is using address or index).
Remove address arg from page_move_anon_rmap(), remove VM_BUG_ON_PAGE,
remove CONFIG_DEBUG_VM PageTransHuge adjustment.
And one more thing: should the compound_head(page) be done inside or
outside page_move_anon_rmap()? It's usually pushed down to the lowest
level nowadays (and mm/memory.c shows no other explicit use of it), so I
think it's better done in page_move_anon_rmap() than by caller.
Fixes: 0798d3c022 ("mm: thp: avoid false positive VM_BUG_ON_PAGE in page_move_anon_rmap()")
Link: http://lkml.kernel.org/r/alpine.LSU.2.11.1607120444540.12528@eggly.anvils
Signed-off-by: Hugh Dickins <hughd@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e41f501d39 upstream.
If CONFIG_KASAN is enabled and gcc is configured with
--disable-initfini-array and/or gold linker is used, gcc emits
.ctors/.dtors and .text.startup/.text.exit sections instead of
.init_array/.fini_array. .dtors section is not explicitly accounted in
the linker script and messes vvar/percpu layout.
We want:
ffffffff822bfd80 D _edata
ffffffff822c0000 D __vvar_beginning_hack
ffffffff822c0000 A __vvar_page
ffffffff822c0080 0000000000000098 D vsyscall_gtod_data
ffffffff822c1000 A __init_begin
ffffffff822c1000 D init_per_cpu__irq_stack_union
ffffffff822c1000 A __per_cpu_load
ffffffff822d3000 D init_per_cpu__gdt_page
We got:
ffffffff8279a600 D _edata
ffffffff8279b000 A __vvar_page
ffffffff8279c000 A __init_begin
ffffffff8279c000 D init_per_cpu__irq_stack_union
ffffffff8279c000 A __per_cpu_load
ffffffff8279e000 D __vvar_beginning_hack
ffffffff8279e080 0000000000000098 D vsyscall_gtod_data
ffffffff827ae000 D init_per_cpu__gdt_page
This happens because __vvar_page and .vvar get different addresses in
arch/x86/kernel/vmlinux.lds.S:
. = ALIGN(PAGE_SIZE);
__vvar_page = .;
.vvar : AT(ADDR(.vvar) - LOAD_OFFSET) {
/* work around gold bug 13023 */
__vvar_beginning_hack = .;
Discard .dtors/.fini_array/.text.exit, since we don't call dtors.
Merge .text.startup into init text.
Link: http://lkml.kernel.org/r/1467386363-120030-1-git-send-email-dvyukov@google.com
Signed-off-by: Dmitry Vyukov <dvyukov@google.com>
Reviewed-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e4568d3803 upstream.
early_pfn_to_nid can return node 0 if a PFN is invalid on machines that
has no node 0. A machine with only node 1 was observed to crash with
the following message:
BUG: unable to handle kernel paging request at 000000000002a3c8
PGD 0
Modules linked in:
Hardware name: Supermicro H8DSP-8/H8DSP-8, BIOS 080011 06/30/2006
task: ffffffff81c0d500 ti: ffffffff81c00000 task.ti: ffffffff81c00000
RIP: reserve_bootmem_region+0x6a/0xef
CR2: 000000000002a3c8 CR3: 0000000001c06000 CR4: 00000000000006b0
Call Trace:
free_all_bootmem+0x4b/0x12a
mem_init+0x70/0xa3
start_kernel+0x25b/0x49b
The problem is that early_page_uninitialised uses the early_pfn_to_nid
helper which returns node 0 for invalid PFNs. No caller of
early_pfn_to_nid cares except early_page_uninitialised. This patch has
early_pfn_to_nid always return a valid node.
Link: http://lkml.kernel.org/r/1468008031-3848-3-git-send-email-mgorman@techsingularity.net
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 63d2f95d63 upstream.
The value `bytes' comes from the filesystem which is about to be
mounted. We cannot trust that the value is always in the range we
expect it to be.
Check its value before using it to calculate the length for the crc32_le
call. It value must be larger (or equal) sumoff + 4.
This fixes a kernel bug when accidentially mounting an image file which
had the nilfs2 magic value 0x3434 at the right offset 0x406 by chance.
The bytes 0x01 0x00 were stored at 0x408 and were interpreted as a
s_bytes value of 1. This caused an underflow when substracting sumoff +
4 (20) in the call to crc32_le.
BUG: unable to handle kernel paging request at ffff88021e600000
IP: crc32_le+0x36/0x100
...
Call Trace:
nilfs_valid_sb.part.5+0x52/0x60 [nilfs2]
nilfs_load_super_block+0x142/0x300 [nilfs2]
init_nilfs+0x60/0x390 [nilfs2]
nilfs_mount+0x302/0x520 [nilfs2]
mount_fs+0x38/0x160
vfs_kern_mount+0x67/0x110
do_mount+0x269/0xe00
SyS_mount+0x9f/0x100
entry_SYSCALL_64_fastpath+0x16/0x71
Link: http://lkml.kernel.org/r/1466778587-5184-2-git-send-email-konishi.ryusuke@lab.ntt.co.jp
Signed-off-by: Torsten Hilbrich <torsten.hilbrich@secunet.com>
Tested-by: Torsten Hilbrich <torsten.hilbrich@secunet.com>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a4f04f2c69 upstream.
If the memory compaction free scanner cannot successfully split a free
page (only possible due to per-zone low watermark), terminate the free
scanner rather than continuing to scan memory needlessly. If the
watermark is insufficient for a free page of order <= cc->order, then
terminate the scanner since all future splits will also likely fail.
This prevents the compaction freeing scanner from scanning all memory on
very large zones (very noticeable for zones > 128GB, for instance) when
all splits will likely fail while holding zone->lock.
compaction_alloc() iterating a 128GB zone has been benchmarked to take
over 400ms on some systems whereas any free page isolated and ready to
be split ends up failing in split_free_page() because of the low
watermark check and thus the iteration continues.
The next time compaction occurs, the freeing scanner will likely start
at the end of the zone again since no success was made previously and we
get the same lengthy iteration until the zone is brought above the low
watermark. All thp page faults can take >400ms in such a state without
this fix.
Link: http://lkml.kernel.org/r/alpine.DEB.2.10.1606211820350.97086@chino.kir.corp.google.com
Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f182270df upstream.
Currently we can have compound pages held on per cpu pagevecs, which
leads to a lot of memory unavailable for reclaim when needed. In the
systems with hundreads of processors it can be GBs of memory.
On of the way of reproducing the problem is to not call munmap
explicitly on all mapped regions (i.e. after receiving SIGTERM). After
that some pages (with THP enabled also huge pages) may end up on
lru_add_pvec, example below.
void main() {
#pragma omp parallel
{
size_t size = 55 * 1000 * 1000; // smaller than MEM/CPUS
void *p = mmap(NULL, size, PROT_READ | PROT_WRITE,
MAP_PRIVATE | MAP_ANONYMOUS , -1, 0);
if (p != MAP_FAILED)
memset(p, 0, size);
//munmap(p, size); // uncomment to make the problem go away
}
}
When we run it with THP enabled it will leave significant amount of
memory on lru_add_pvec. This memory will be not reclaimed if we hit
OOM, so when we run above program in a loop:
for i in `seq 100`; do ./a.out; done
many processes (95% in my case) will be killed by OOM.
The primary point of the LRU add cache is to save the zone lru_lock
contention with a hope that more pages will belong to the same zone and
so their addition can be batched. The huge page is already a form of
batched addition (it will add 512 worth of memory in one go) so skipping
the batching seems like a safer option when compared to a potential
excess in the caching which can be quite large and much harder to fix
because lru_add_drain_all is way to expensive and it is not really clear
what would be a good moment to call it.
Similarly we can reproduce the problem on lru_deactivate_pvec by adding:
madvise(p, size, MADV_FREE); after memset.
This patch flushes lru pvecs on compound page arrival making the problem
less severe - after applying it kill rate of above example drops to 0%,
due to reducing maximum amount of memory held on pvec from 28MB (with
THP) to 56kB per CPU.
Suggested-by: Michal Hocko <mhocko@suse.com>
Link: http://lkml.kernel.org/r/1466180198-18854-1-git-send-email-lukasz.odzioba@intel.com
Signed-off-by: Lukasz Odzioba <lukasz.odzioba@intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Kirill Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Vladimir Davydov <vdavydov@parallels.com>
Cc: Ming Li <mingli199x@qq.com>
Cc: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e838a45f93 upstream.
Commit d0164adc89 ("mm, page_alloc: distinguish between being unable
to sleep, unwilling to sleep and avoiding waking kswapd") modified
__GFP_WAIT to explicitly identify the difference between atomic callers
and those that were unwilling to sleep. Later the definition was
removed entirely.
The GFP_RECLAIM_MASK is the set of flags that affect watermark checking
and reclaim behaviour but __GFP_ATOMIC was never added. Without it,
atomic users of the slab allocator strip the __GFP_ATOMIC flag and
cannot access the page allocator atomic reserves. This patch addresses
the problem.
The user-visible impact depends on the workload but potentially atomic
allocations unnecessarily fail without this path.
Link: http://lkml.kernel.org/r/20160610093832.GK2527@techsingularity.net
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Reported-by: Marcin Wojtas <mw@semihalf.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9295c41d77 upstream.
Due to the way CUBC register is updated, a double flush is needed to
compute an accurate residue. First flush aim is to get data from the DMA
FIFO and second one ensures that we won't report data which are not in
memory.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: e1f7c9eee7 ("dmaengine: at_xdmac: creation of the atmel
eXtended DMA Controller driver")
Reviewed-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 53398f4888 upstream.
An unexpected value of CUBC can lead to a corrupted residue. A more
complex sequence is needed to detect an inaccurate value for NCA or CUBC.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: e1f7c9eee7 ("dmaengine: at_xdmac: creation of the atmel
eXtended DMA Controller driver")
Reviewed-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit abb2bafd29 upstream.
The EFI firmware on Macs contains a full-fledged network stack for
downloading OS X images from osrecovery.apple.com. Unfortunately
on Macs introduced 2011 and 2012, EFI brings up the Broadcom 4331
wireless card on every boot and leaves it enabled even after
ExitBootServices has been called. The card continues to assert its IRQ
line, causing spurious interrupts if the IRQ is shared. It also corrupts
memory by DMAing received packets, allowing for remote code execution
over the air. This only stops when a driver is loaded for the wireless
card, which may be never if the driver is not installed or blacklisted.
The issue seems to be constrained to the Broadcom 4331. Chris Milsted
has verified that the newer Broadcom 4360 built into the MacBookPro11,3
(2013/2014) does not exhibit this behaviour. The chances that Apple will
ever supply a firmware fix for the older machines appear to be zero.
The solution is to reset the card on boot by writing to a reset bit in
its mmio space. This must be done as an early quirk and not as a plain
vanilla PCI quirk to successfully combat memory corruption by DMAed
packets: Matthew Garrett found out in 2012 that the packets are written
to EfiBootServicesData memory (http://mjg59.dreamwidth.org/11235.html).
This type of memory is made available to the page allocator by
efi_free_boot_services(). Plain vanilla PCI quirks run much later, in
subsys initcall level. In-between a time window would be open for memory
corruption. Random crashes occurring in this time window and attributed
to DMAed packets have indeed been observed in the wild by Chris
Bainbridge.
When Matthew Garrett analyzed the memory corruption issue in 2012, he
sought to fix it with a grub quirk which transitions the card to D3hot:
http://git.savannah.gnu.org/cgit/grub.git/commit/?id=9d34bb85da56
This approach does not help users with other bootloaders and while it
may prevent DMAed packets, it does not cure the spurious interrupts
emanating from the card. Unfortunately the card's mmio space is
inaccessible in D3hot, so to reset it, we have to undo the effect of
Matthew's grub patch and transition the card back to D0.
Note that the quirk takes a few shortcuts to reduce the amount of code:
The size of BAR 0 and the location of the PM capability is identical
on all affected machines and therefore hardcoded. Only the address of
BAR 0 differs between models. Also, it is assumed that the BCMA core
currently mapped is the 802.11 core. The EFI driver seems to always take
care of this.
Michael Büsch, Bjorn Helgaas and Matt Fleming contributed feedback
towards finding the best solution to this problem.
The following should be a comprehensive list of affected models:
iMac13,1 2012 21.5" [Root Port 00:1c.3 = 8086:1e16]
iMac13,2 2012 27" [Root Port 00:1c.3 = 8086:1e16]
Macmini5,1 2011 i5 2.3 GHz [Root Port 00:1c.1 = 8086:1c12]
Macmini5,2 2011 i5 2.5 GHz [Root Port 00:1c.1 = 8086:1c12]
Macmini5,3 2011 i7 2.0 GHz [Root Port 00:1c.1 = 8086:1c12]
Macmini6,1 2012 i5 2.5 GHz [Root Port 00:1c.1 = 8086:1e12]
Macmini6,2 2012 i7 2.3 GHz [Root Port 00:1c.1 = 8086:1e12]
MacBookPro8,1 2011 13" [Root Port 00:1c.1 = 8086:1c12]
MacBookPro8,2 2011 15" [Root Port 00:1c.1 = 8086:1c12]
MacBookPro8,3 2011 17" [Root Port 00:1c.1 = 8086:1c12]
MacBookPro9,1 2012 15" [Root Port 00:1c.1 = 8086:1e12]
MacBookPro9,2 2012 13" [Root Port 00:1c.1 = 8086:1e12]
MacBookPro10,1 2012 15" [Root Port 00:1c.1 = 8086:1e12]
MacBookPro10,2 2012 13" [Root Port 00:1c.1 = 8086:1e12]
For posterity, spurious interrupts caused by the Broadcom 4331 wireless
card resulted in splats like this (stacktrace omitted):
irq 17: nobody cared (try booting with the "irqpoll" option)
handlers:
[<ffffffff81374370>] pcie_isr
[<ffffffffc0704550>] sdhci_irq [sdhci] threaded [<ffffffffc07013c0>] sdhci_thread_irq [sdhci]
[<ffffffffc0a0b960>] azx_interrupt [snd_hda_codec]
Disabling IRQ #17
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=79301
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=111781
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=728916
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=895951#c16
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1009819
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1098621
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1149632#c5
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1279130
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1332732
Tested-by: Konstantin Simanov <k.simanov@stlk.ru> # [MacBookPro8,1]
Tested-by: Lukas Wunner <lukas@wunner.de> # [MacBookPro9,1]
Tested-by: Bryan Paradis <bryan.paradis@gmail.com> # [MacBookPro9,2]
Tested-by: Andrew Worsley <amworsley@gmail.com> # [MacBookPro10,1]
Tested-by: Chris Bainbridge <chris.bainbridge@gmail.com> # [MacBookPro10,2]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Chris Milsted <cmilsted@redhat.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Michael Buesch <m@bues.ch>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: b43-dev@lists.infradead.org
Cc: linux-pci@vger.kernel.org
Cc: linux-wireless@vger.kernel.org
Link: http://lkml.kernel.org/r/48d0972ac82a53d460e5fce77a07b2560db95203.1465690253.git.lukas@wunner.de
[ Did minor readability edits. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 850c321027 upstream.
We used to scan secondary buses until the following commit that
was applied in 2009:
8659c406ad ("x86: only scan the root bus in early PCI quirks")
which commit constrained early quirks to the root bus only. Its
motivation was to prevent application of the nvidia_bugs quirk
on secondary buses.
We're about to add a quirk to reset the Broadcom 4331 wireless card on
2011/2012 Macs, which is located on a secondary bus behind a PCIe root
port. To facilitate that, reintroduce scanning of secondary buses.
The commit message of 8659c406ad notes that scanning only the root bus
"saves quite some unnecessary scanning work". The algorithm used prior
to 8659c406ad was particularly time consuming because it scanned
buses 0 to 31 brute force. To avoid lengthening boot time, employ a
recursive strategy which only scans buses that are actually reachable
from the root bus.
Yinghai Lu pointed out that the secondary bus number read from a
bridge's config space may be invalid, in particular a value of 0 would
cause an infinite loop. The PCI core goes beyond that and recurses to a
child bus only if its bus number is greater than the parent bus number
(see pci_scan_bridge()). Since the root bus is numbered 0, this implies
that secondary buses may not be 0. Do the same on early scanning.
If this algorithm is found to significantly impact boot time or cause
infinite loops on broken hardware, it would be possible to limit its
recursion depth: The Broadcom 4331 quirk applies at depth 1, all others
at depth 0, so the bus need not be scanned deeper than that for now. An
alternative approach would be to revert to scanning only the root bus,
and apply the Broadcom 4331 quirk to the root ports 8086:1c12, 8086:1e12
and 8086:1e16. Apple always positioned the card behind either of these
three ports. The quirk would then check presence of the card in slot 0
below the root port and do its deed.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: linux-pci@vger.kernel.org
Link: http://lkml.kernel.org/r/f0daa70dac1a9b2483abdb31887173eb6ab77bdf.1465690253.git.lukas@wunner.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c66f59ee50 upstream.
Since ed_schedule begins with marking the ED as "operational",
the ED may be left in such state even if scheduling actually
fails.
This allows future submission attempts to smuggle this ED to the
hardware behind the scheduler's back and without linking it to
the ohci->eds_in_use list.
The former causes bandwidth saturation and data loss on isoc
endpoints, the latter crashes the kernel when attempt is made
to unlink such ED from this list.
Fix ed_schedule to update ED state only on successful return.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7c0b5991d upstream.
overlay needs underlying fs to support d_type. Recently I put in a
patch in to detect this condition and started failing mount if
underlying fs did not support d_type.
But this breaks existing configurations over kernel upgrade. Those who
are running docker (partially broken configuration) with xfs not
supporting d_type, are surprised that after kernel upgrade docker does
not run anymore.
https://github.com/docker/docker/issues/22937#issuecomment-229881315
So instead of erroring out, detect broken configuration and warn
about it. This should allow existing docker setups to continue
working after kernel upgrade.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Fixes: 45aebeaf4f ("ovl: Ensure upper filesystem supports d_type")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 21765194ce upstream.
d_type check requires successful creation of workdir as iterates
through work dir and expects work dir to be present in it. If that's
not the case, this check will always return d_type not supported even
if underlying filesystem might be supporting it.
So don't do this check if work dir creation failed in previous step.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81dc0365cf upstream.
Parallel build can sporadically fail because asn1 headers may
not be built yet by the time qat_asym_algs.o is compiled:
drivers/crypto/qat/qat_common/qat_asym_algs.c:55:32: fatal error: qat_rsapubkey-asn1.h: No such file or directory
#include "qat_rsapubkey-asn1.h"
Signed-off-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7f55656703 upstream.
The well-spotted fallocate undo fix is good in most cases, but not when
fallocate failed on the very first page. index 0 then passes lend -1
to shmem_undo_range(), and that has two bad effects: (a) that it will
undo every fallocation throughout the file, unrestricted by the current
range; but more importantly (b) it can cause the undo to hang, because
lend -1 is treated as truncation, which makes it keep on retrying until
every page has gone, but those already fully instantiated will never go
away. Big thank you to xfstests generic/269 which demonstrates this.
Fixes: b9b4bb26af ("tmpfs: don't undo fallocate past its last page")
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f2d9d9921 upstream.
As of Xen 4.7 PV CPUID doesn't expose either of CPUID[1].ECX[7] and
CPUID[0x80000007].EDX[7] anymore, causing the driver to fail to load on
both Intel and AMD systems. Doing any kind of hardware capability
checks in the driver as a prerequisite was wrong anyway: With the
hypervisor being in charge, all such checking should be done by it. If
ACPI data gets uploaded despite some missing capability, the hypervisor
is free to ignore part or all of that data.
Ditch the entire check_prereq() function, and do the only valid check
(xen_initial_domain()) in the caller in its place.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45e8a2583d upstream.
POSIX allows files with trailing spaces or a trailing period but
SMB3 does not, so convert these using the normal Services For Mac
mapping as we do for other reserved characters such as
: < > | ? *
This is similar to what Macs do for the same problem over SMB3.
Signed-off-by: Steve French <steve.french@primarydata.com>
Acked-by: Pavel Shilovsky <pshilovsky@samba.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b8da344b74 upstream.
In sess_auth_rawntlmssp_authenticate(), the ntlmssp blob is allocated
statically and its size is an "empirical" 5*sizeof(struct
_AUTHENTICATE_MESSAGE) (320B on x86_64). I don't know where this value
comes from or if it was ever appropriate, but it is currently
insufficient: the user and domain name in UTF16 could take 1kB by
themselves. Because of that, build_ntlmssp_auth_blob() might corrupt
memory (out-of-bounds write). The size of ntlmssp_blob in
SMB2_sess_setup() is too small too (sizeof(struct _NEGOTIATE_MESSAGE)
+ 500).
This patch allocates the blob dynamically in
build_ntlmssp_auth_blob().
Signed-off-by: Jerome Marchand <jmarchan@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4fcd1813e6 upstream.
Azure server blocks clients that open a socket and don't do anything on it.
In our reconnect scenarios, we can reconnect the tcp session and
detect the socket is available but we defer the negprot and SMB3 session
setup and tree connect reconnection until the next i/o is requested, but
this looks suspicous to some servers who expect SMB3 negprog and session
setup soon after a socket is created.
In the echo thread, reconnect SMB3 sessions and tree connections
that are disconnected. A later patch will replay persistent (and
resilient) handle opens.
Signed-off-by: Steve French <steve.french@primarydata.com>
Acked-by: Pavel Shilovsky <pshilovsky@samba.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8beb330044 upstream.
The untagged command case in the 53c700 driver has been broken since
host wide tags were enabled because the replaced scsi_find_tag()
function had a special case for the tag value SCSI_NO_TAG to retrieve
sdev->current_cmnd. The replacement function scsi_host_find_tag() has
no such special case and returns NULL causing untagged commands to
trigger a BUG() in the driver. Inspection shows that the 53c700 is the
only driver using this SCSI_NO_TAG case, so a local fix in the driver
suffices to fix this problem globally.
Fixes: 64d513ac31 - "scsi: use host wide tags by default"
Reported-by: Helge Deller <deller@gmx.de>
Tested-by: Helge Deller <deller@gmx.de>
Signed-off-by: James Bottomley <jejb@linux.vnet.ibm.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5419447e21 upstream.
This reverts commit 852ffd0f4e.
There are use cases where an intermediate boot kernel (1) uses kexec
to boot the final production kernel (2). For this scenario we should
provide the original boot information to the production kernel (2).
Therefore clearing the boot information during kexec() should not
be done.
Reported-by: Steffen Maier <maier@linux.vnet.ibm.com>
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bcf4dd5f9e upstream.
The test_fp_ctl function is used to test if a given value is a valid
floating-point control. The inline assembly in test_fp_ctl uses an
incorrect constraint for the 'orig_fpc' variable. If the compiler
chooses the same register for 'fpc' and 'orig_fpc' the test_fp_ctl()
function always returns true. This allows user space to trigger
kernel oopses with invalid floating-point control values on the
signal stack.
This problem has been introduced with git commit 4725c86055
"s390: fix save and restore of the floating-point-control register"
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 72d8c36ec3 upstream.
sas_ata_strategy_handler() adds the works of the ata error handler to
system_unbound_wq. This workqueue asynchronously runs work items, so the
ata error handler will be performed concurrently on different CPUs. In
this case, ->host_failed will be decreased simultaneously in
scsi_eh_finish_cmd() on different CPUs, and become abnormal.
It will lead to permanently inequality between ->host_failed and
->host_busy, and scsi error handler thread won't start running. IO
errors after that won't be handled.
Since all scmds must have been handled in the strategy handler, just
remove the decrement in scsi_eh_finish_cmd() and zero ->host_busy after
the strategy handler to fix this race.
Fixes: 50824d6c56 ("[SCSI] libsas: async ata-eh")
Signed-off-by: Wei Fang <fangwei1@huawei.com>
Reviewed-by: James Bottomley <jejb@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cfc9fde0b0 upstream.
The upper dentry may become stale before we call ovl_lock_rename_workdir.
For example, someone could (mistakenly or maliciously) manually unlink(2)
it directly from upperdir.
To ensure it is not stale, let's lookup it after ovl_lock_rename_workdir
and and check if it matches the upper dentry.
Essentially, it is the same problem and similar solution as in
commit 11f3710417 ("ovl: verify upper dentry before unlink and rename").
Signed-off-by: Maxim Patlasov <mpatlasov@virtuozzo.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b99c2d9138 upstream.
Before 4bacc9c923 ("overlayfs: Make f_path...") file->f_path pointed to
the underlying file, hence suid/sgid removal on write worked fine.
After that patch file->f_path pointed to the overlay file, and the file
mode bits weren't copied to overlay_inode->i_mode. So the suid/sgid
removal simply stopped working.
The fix is to copy the mode bits, but then ovl_setattr() needs to clear
ATTR_MODE to avoid the BUG() in notify_change(). So do this first, then in
the next patch copy the mode.
Reported-by: Eryu Guan <eguan@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Fixes: 4bacc9c923 ("overlayfs: Make f_path always point to the overlay and f_inode to the underlay")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07a2daab49 upstream.
Right now when a new overlay inode is created, we initialize overlay
inode's ->i_mode from underlying inode ->i_mode but we retain only
file type bits (S_IFMT) and discard permission bits.
This patch changes it and retains permission bits too. This should allow
overlay to do permission checks on overlay inode itself in task context.
[SzM] It also fixes clearing suid/sgid bits on write.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Reported-by: Eryu Guan <eguan@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Fixes: 4bacc9c923 ("overlayfs: Make f_path always point to the overlay and f_inode to the underlay")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 03bea60409 upstream.
When truncating a file we should check write access on the underlying
inode. And we should do so on the lower file as well (before copy-up) for
consistency.
Original patch and test case by Aihua Zhang.
- - >o >o - - test.c - - >o >o - -
#include <stdio.h>
#include <errno.h>
#include <unistd.h>
int main(int argc, char *argv[])
{
int ret;
ret = truncate(argv[0], 4096);
if (ret != -1) {
fprintf(stderr, "truncate(argv[0]) should have failed\n");
return 1;
}
if (errno != ETXTBSY) {
perror("truncate(argv[0])");
return 1;
}
return 0;
}
- - >o >o - - >o >o - - >o >o - -
Reported-by: Aihua Zhang <zhangaihua1@huawei.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a4859d7594 upstream.
When using the 'default_permissions' mount option, ovl_permission() on
non-directories was missing a dput(alias), resulting in "BUG Dentry still
in use".
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Fixes: 8d3095f4ad ("ovl: default permissions")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c5379ba8fc upstream.
Until now, our understanding for HW I/O coherency to work on the
Cortex-A9 based Marvell SoC was that only the PCIe regions should be
mapped strongly-ordered. However, we were still encountering some
deadlocks, especially when testing the CESA crypto engine. After
checking with the HW designers, it was concluded that all the MMIO
registers should be mapped as strongly ordered for the HW I/O coherency
mechanism to work properly.
This fixes some easy to reproduce deadlocks with the CESA crypto engine
driver (dmcrypt on a sufficiently large disk partition).
Tested-by: Terry Stockert <stockert@inkblotadmirer.me>
Tested-by: Romain Perier <romain.perier@free-electrons.com>
Cc: Terry Stockert <stockert@inkblotadmirer.me>
Cc: Romain Perier <romain.perier@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 929e604efa upstream.
When the support for the Marvell crypto engine was added in the Device
Tree of the various Armada 385 Device Tree files in commit
d716f2e837 ("ARM: mvebu: define crypto SRAM ranges for all armada-38x
boards"), a typo was made in the MBus window attributes for the Armada
385 Linksys board: 0x09/0x05 are used instead of 0x19/0x15. This commit
fixes this typo, which makes the CESA engines operational on Armada 385
Linksys boards.
Reported-by: Terry Stockert <stockert@inkblotadmirer.me>
Cc: Terry Stockert <stockert@inkblotadmirer.me>
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: d716f2e837 ("ARM: mvebu: define crypto SRAM ranges for all armada-38x boards")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5fc39d3472 upstream.
The sun4i-timer driver registers its sched_clock only if the machine is
compatible with "allwinner,sun5i-a13", "allwinner,sun5i-a10s" or
"allwinner,sun4i-a10".
Add the missing "allwinner,sun5i-a13" string to the machine compatible.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: 465a225fb2 ("ARM: sun5i: Add C.H.I.P DTS")
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d716fb03f7 upstream.
This allows the device to correctly show up as ATI HDMI
rather than a generic one and allows the driver to use
the available caps.
Signed-off-by: Awais Belal <awais_belal@mentor.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ab58d8cc87 upstream.
register_vga_switcheroo() sets the PM ops from the hda structure which
is freed later in azx_free. Make sure that these ops are cleared.
Caught by KASAN, initially noticed due to a general protection fault.
Fixes: 246efa4a07 ("snd/hda: add runtime suspend/resume on optimus support (v4)")
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f388cdcdd1 upstream.
snd_ctl_remove() has a notification for the removal event. It's
superfluous when done during the device got disconnected. Although
the notification itself is mostly harmless, it may potentially be
harmful, and should be suppressed. Actually some components PCM may
free ctl elements during the disconnect or free callbacks, thus it's
no theoretical issue.
This patch adds the check of card->shutdown flag for avoiding
unnecessary notifications after (or during) the disconnect.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8ff48cb70 upstream.
The chmap ctls assigned to PCM streams are freed in the PCM disconnect
callback. However, since the disconnect callback isn't called when
the card gets freed before registering, the chmap ctls may still be
left assigned. They are eventually freed together with other ctls,
but it may cause an Oops at pcm_chmap_ctl_private_free(), as the
function refers to the assigned PCM stream, while the PCM objects have
been already freed beforehand.
The fix is to free the chmap ctls also at PCM free callback, not only
at PCM disconnect.
Reported-by: Laxminath Kasam <b_lkasam@codeaurora.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a132099f0 upstream.
We have some Dell laptops which can't detect headset mic, the machines
use the codec ALC225, they have some new pin configuration values,
after adding them in the alc225 pin quirk table, they work well.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3fa6993fef upstream.
The user timer tu->qused counter may go to a negative value when
multiple concurrent reads are performed since both the check and the
decrement of tu->qused are done in two individual locked contexts.
This results in bogus read outs, and the endless loop in the
user-space side.
The fix is to move the decrement of the tu->qused counter into the
same spinlock context as the zero-check of the counter.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9c6795a9b3 upstream.
'commpage_bak' is allocated with 'sizeof(struct echoaudio)' bytes.
We then copy 'sizeof(struct comm_page)' bytes in it.
On my system, smatch complains because one is 2960 and the other is 3072.
This would result in memory corruption or a oops.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 62db7152c9 upstream.
vortex_wtdma_bufshift() function does calculate the page index
wrongly, first masking then shift, which always results in zero.
The proper computation is to first shift, then mask.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f83c32925d upstream.
The new Dell laptop with codec 3246 can't detect headset mic when
headset was inserted on the machine. So adding pin configurations
into quirk table makes headset mic work correctly.
Codec: Realtek ALC3246
Vendor Id: 0x10ec0256
Subsystem Id: 0x10280781
Signed-off-by: Woodrow Shen <woodrow.shen@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8198868f0a upstream.
Call path:
1) snd_hdac_power_up_pm()
2) snd_hdac_power_up()
3) pm_runtime_get_sync()
4) __pm_runtime_resume()
5) rpm_resume()
The rpm_resume() returns 1 when the device is already active.
Because the return value is unmodified, the hdac regmap read/write
functions should allow this value for the retry I/O operation, too.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ce91714b0 upstream.
On more Dell machines (e.g. Dell Precision M3800) fan_type() call is too
expensive (CPU is too long in SMM mode) and cause kernel to hang. This is
bug in Dell SMM or BIOS.
This patch caches type for each fan (as it should not change) and changes
the way how fan presense is detected. First it try function fan_status()
as was before commit f989e55452 ("i8k: Add support for fan labels"). And
if that fails fallback to fan_type(). *_status() functions can fail in case
fan is not currently accessible (e.g. present on GPU which is currently
turned off).
Reported-by: Tolga Cakir <cevelnet@gmail.com>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=112021
Tested-by: Tolga Cakir <cevelnet@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2744d2fde0 upstream.
Some Dell machines have especially broken SMM or BIOS which cause that once
fan_type() is called then CPU fan speed going randomly up and down. And for
fixing this behaviour reboot is required.
So this patch creates fan_type blacklist of affected Dell machines and
disallow fan_type() call on them to prevent that erratic behaviour.
Old blacklist which disabled loading driver on some machines added in
commits a4b45b25f1 ("hwmon: (dell-smm) Blacklist Dell Studio XPS 8100")
and 6220f4ebd7 ("hwmon: (dell-smm) Blacklist Dell Studio XPS 8000") were
moved to FAN_TYPE blacklist.
Reported-by: Jan C Peters <jcpeters89@gmail.com>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=100121
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7613663cc1 upstream.
For security reasons ordinary user must not be able to control fan speed
via /proc/i8k by default. Some malicious software running under "nobody"
user could be able to turn fan off and cause HW problems. So this patch
changes default value of "restricted" parameter to 1.
Also restrict reading of DMI_PRODUCT_SERIAL from /proc/i8k via "restricted"
parameter. It is because non root user cannot read DMI_PRODUCT_SERIAL from
sysfs file /sys/class/dmi/id/product_serial.
Old non secure behaviour of file /proc/i8k can be achieved by loading this
module with "restricted" parameter set to 0.
Note that this patch has effects only for kernels compiled with CONFIG_I8K
and only for file /proc/i8k. Hwmon interface provided by this driver was
not changed and root access for setting fan speed was needed also before.
Reported-by: Mario Limonciello <Mario_Limonciello@dell.com>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 510cccb5b0 upstream.
The size of individual keymap in drivers/tty/vt/keyboard.c is NR_KEYS,
which is currently 256, whereas number of keys/buttons in input device (and
therefor in key_down) is much larger - KEY_CNT - 768, and that can cause
out-of-bound access when we do
sym = U(key_maps[0][k]);
with large 'k'.
To fix it we should not attempt iterating beyond smaller of NR_KEYS and
KEY_CNT.
Also while at it let's switch to for_each_set_bit() instead of open-coding
it.
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b45996d2e upstream.
We are getting somewhat random soft lockups with this signature:
[ 86.992215] [<fffffc00080935e0>] el1_irq+0xa0/0x10c
[ 86.997082] [<fffffc000841822c>] cursor_timer_handler+0x30/0x54
[ 87.002991] [<fffffc000810ec44>] call_timer_fn+0x54/0x1a8
[ 87.008378] [<fffffc000810ef88>] run_timer_softirq+0x1c4/0x2bc
[ 87.014200] [<fffffc000809077c>] __do_softirq+0x114/0x344
[ 87.019590] [<fffffc00080af45c>] irq_exit+0x74/0x98
[ 87.024458] [<fffffc00080fac20>] __handle_domain_irq+0x98/0xfc
[ 87.030278] [<fffffc000809056c>] gic_handle_irq+0x94/0x190
This is caused by the vt visual_init() function calling into
fbcon_init() with a vc_cur_blink_ms value of zero. This is a
transient condition, as it is later set to a non-zero value. But, if
the timer happens to expire while the blink rate is zero, it goes into
an endless loop, and we get soft lockup.
The fix is to initialize vc_cur_blink_ms before calling the con_init()
function.
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Scot Doyle <lkml14@scotdoyle.com>
Tested-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 68b356eb3d upstream.
Currently the ad7266 driver treats any failure to get vref as though the
regulator were not present but this means that if probe deferral is
triggered the driver will act as though the regulator were not present.
Instead only use the internal reference if we explicitly got -ENODEV which
is what is returned for absent regulators.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e5511c816e upstream.
The ad7266 driver attempts to support deciding between the use of internal
and external power supplies by checking to see if an error is returned when
requesting the regulator. This doesn't work with the current code since the
driver uses a normal regulator_get() which is for non-optional supplies
and so assumes that if a regulator is not provided by the platform then
this is a bug in the platform integration and so substitutes a dummy
regulator. Use regulator_get_optional() instead which indicates to the
framework that the regulator may be absent and provides a dummy regulator
instead.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b7f4e25f3 upstream.
All regulator_get() variants return either a pointer to a regulator or an
ERR_PTR() so testing for NULL makes no sense and may lead to bugs if we
use NULL as a valid regulator. Fix this by using IS_ERR() as expected.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c1f91b985 upstream.
These two spi_w8r8() calls return a value with is used by the code
following the error check. The dubious use was caused by a cleanup
patch.
Fixes: d34dbee8ac ("staging:iio:accel:kxsd9 cleanup and conversion to iio_chan_spec.")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09bc0ddaab upstream.
IIO_TEMP channel was being incorrectly reported back as Celsius when it
should have been milliCelsius. This is via an incorrect scale value being
returned to userspace.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0e35cf5ce0 upstream.
Apply the correct mask to enable all available humidity integration
times. Currently, the driver defaults to 6500 and all is okay with that.
However, if 3850 is selected we get a stuck bit and can't change back
to 6500 or select 2500. (Verified with HDC1008)
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Reviewed-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5138806f16 upstream.
IIO_CHAN_INFO_RAW was returning processed data which was incorrect.
This also adds the IIO_CHAN_INFO_SCALE value to convert to a processed value.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 590b92a302 upstream.
Without this, the iio:deviceX is missing in the /sys/bus/i2c/devices/0-0039
Some userspace tools use this path to identify a specific instance of the
device.
Signed-off-by: Yong Li <sdliyong@gmail.com>
Reviewed-By: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d43a41152f upstream.
Temperature channels report scaled samples in Celsius although expected as
milli degree Celsius in Documentation/ABI/testing/sysfs-bus-iio.
Gains are not implemented at all for LPS001WP pressure and temperature
channels.
This patch ensures that proper offsets and scales are exposed to userpace
for both pressure and temperature channels.
Also fix a NULL pointer exception when userspace reads content of sysfs
scale attribute when gains are not defined.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9954382335 upstream.
When attaching a pollfunc iio_trigger_attach_poll_func will allocate a
virtual irq and call the driver's set_trigger_state function. Fix error
handling to undo previous steps if any fails.
In particular this fixes handling errors from a driver's
set_trigger_state function. When using triggered buffers a failure to
enable the trigger used to make the buffer unusable.
Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef0dab4aae upstream.
The save/restore buffers for VC state is first composed of a 2-byte control
register, then a bunch of 4-byte words.
This causes unaligned accesses which trap on platform such as sparc.
This is easy to fix by simply moving the buffer pointer forward by 4 bytes
instead of 2 after dealing with the control register. The length
adjustment needs to be changed likewise as well.
Fixes: 5f8fc43217 ("PCI: Include pci/pcie/Kconfig directly from pci/Kconfig")
Reported-by: Meelis Roos <mroos@linux.ee>
Reported-by: Anatoly Pugachev <matorola@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f50b8e574 upstream.
In the omap gpmc driver it can be noticed that GPMC_CONFIG4_OEEXTRADELAY
is overwritten by the WEEXTRADELAY value from the device tree and
GPMC_CONFIG4_WEEXTRADELAY is not updated by the value from the device
tree.
As a consequence, the memory accesses cannot be configured properly when
the extra delay are needed for OE and WE.
Fix the update of GPMC_CONFIG4_WEEXTRADELAY with the value from the
device tree file and prevents GPMC_CONFIG4_OEXTRADELAY
being overwritten by the WEXTRADELAY value from the device tree.
Signed-off-by: Ocquidant, Sebastien <sebastienocquidant@eaton.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit beca4cf553 upstream.
When the surface backing a framebuffer doesn't match the framebuffer's
dimensions, the screen target code would test the framebuffer dimensions
rather than the surface dimensions when deciding whether to bind the
surface as a screen target directly. This causes a screen target -
surface dimension mismatch and a subsequent device error.
Fix this by testing against the surface dimension.
v2: Fix review comments by Sinclair Yeh.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d5f1a291e3 upstream.
For the Screen Object display unit, we need to reserve a
guest-invisible region equal to the size of the framebuffer for
the host. This region can only be reserved in VRAM, whereas
the guest-visible framebuffer can be reserved in either VRAM or
GMR.
As such priority should be given to the guest-invisible
region otherwise in a limited VRAM situation, we can fail to
allocate this region.
This patch makes it so that vmw_sou_backing_alloc() is called
before the framebuffer is pinned.
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4ed7e2242b upstream.
In certain scenarios, e.g. when fbdev is enabled, we can get into
a situation where a vmw_framebuffer_pin() is called on a buffer
that is already pinned.
When this happens, ttm_bo_validate() will unintentially remove the
TTM_PL_FLAG_NO_EVICT flag, thus unpinning it, and leaving no way
to actually pin the buffer again.
To prevent this, if a buffer is already pinned, then instead of
calling ttm_bo_validate(), just make sure the proposed placement is
compatible with the existing placement.
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c20d213dd upstream.
In a low-memory 2D VM, fbdev can take up a large percentage of
available memory, making them unavailable for other DRM clients.
Since we do not take fbdev into account when filtering modes,
we end up claiming to support more modes than we actually do.
As a result, users get a black screen when setting a mode too
large for current available memory. In a low-memory VM
configuration, users can get a black screen for a mode as low
as 1024x768.
The current mode filtering mechanism keys off of
SVGA_REG_SUGGESTED_GBOBJECT_MEM_SIZE_KB, i.e. the maximum amount
of surface memory we have. Since this value is a performance
suggestion, not a hard limit, and since there should not be much
of a performance impact for a 2D VM, rather than filtering out
more modes, we will just allow ourselves to exceed the SVGA's
performance suggestion.
Also changed assumed bpp to 32 from 16 to make sure we can
actually support all the modes listed.
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 04319d89fb upstream.
Offer an option for advanced users who want larger modes at 16bpp.
This becomes necessary after the fix: "Work around mode set
failure in 2D VMs." Without this patch, there would be no way
for existing advanced users to get to a high res mode, and the
regression is they will likely get a black screen after a software
update on their current VM.
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 94477bff39 upstream.
There are cases where it is desired to see if a proposed placement
is compatible with a buffer object before calling ttm_bo_validate().
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit afe705be38 upstream.
Since the introduction of (struct_mutex) lockless GEM bo freeing, there
are a pair of driver vfuncs for freeing the GEM bo, of which the driver
may choose to only implement driver->gem_object_free_unlocked (and so
avoid taking the struct_mutex along the free path). However, the CMA GEM
helpers were still calling driver->gem_free_object directly, now NULL,
and promptly dying on the fancy new lockless drivers. Oops.
Robert Foss bisected this to b82caafcf2 (drm/vc4: Use lockless gem BO
free callback) on his vc4 device, but that just serves as an enabler for
9f0ba539d1 (drm/gem: support BO freeing without dev->struct_mutex).
Reported-by: Robert Foss <robert.foss@collabora.com>
Fixes: 9f0ba539d1 (drm/gem: support BO freeing without dev->struct_mutex)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Robert Foss <robert.foss@collabora.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Robert Foss <robert.foss@collabora.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6709887c44 upstream.
drm_atomic_set_mode_prop_for_crtc() does not clear the state->mode, so
old data may be left there when a new mode is set, possibly causing odd
issues.
This patch improves the situation by always clearing the state->mode
first.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b201e743f4 upstream.
When setting mode via MODE_ID property,
drm_atomic_set_mode_prop_for_crtc() does not call
drm_mode_set_crtcinfo() which possibly causes:
"[drm:drm_calc_timestamping_constants [drm]] *ERROR* crtc 32: Can't
calculate constants, dotclock = 0!"
Whether the error is seen depends on the previous data in state->mode,
as state->mode is not cleared when setting new mode.
This patch adds drm_mode_set_crtcinfo() call to
drm_mode_convert_umode(), which is called in both legacy and atomic
paths. This should be fine as there's no reason to call
drm_mode_convert_umode() without also setting the crtc related fields.
drm_mode_set_crtcinfo() is removed from the legacy drm_mode_setcrtc() as
that is no longer needed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 664a84d2c7 upstream.
During hibernation the cached DP port register value will be left with
whatever value we have there when we create the hibernation image.
Currently that means the port (and eDP PLL) will be off in the cached
value. However when we resume there is no guarantee that the value
in the actual register will match the cached value. If i915 isn't
loaded in the kernel that loads the hibernation image, the port may
well be on (eg. left on by the BIOS). The encoder state readout
does the right thing in this case and updates our encoder state
to reflect the actual hardware state. However the post-resume modeset
will then use the stale cached port register value in
intel_dp_link_down() and potentially confuse the hardware.
This was caught by the following assert
WARNING: CPU: 3 PID: 5288 at ../drivers/gpu/drm/i915/intel_dp.c:2184 assert_edp_pll+0x99/0xa0 [i915]
eDP PLL state assertion failure (expected on, current off)
on account of the eDP PLL getting prematurely turned off when
shutting down the port, since the DP_PLL_ENABLE bit wasn't set
in the cached register value.
Presumably I introduced this problem in
commit 6fec766283 ("drm/i915: Use intel_dp->DP in eDP PLL setup")
as before that we didn't update the cached value after shuttting the
port down. That's assuming the port got enabled at least once prior
to hibernating. If that didn't happen then the cached value would
still have been totally out of sync with reality (eg. first boot w/o
eDP on, then hibernate, and then resume with eDP on).
So, let's fix this properly and refresh the cached register value from
the hardware register during resume.
DDI platforms shouldn't use the cached value during port disable at
least, so shouldn't have this particular issue. They might still have
issues if we skip the initial modeset and then try to retrain the link
or something. But untangling this DP vs. DDI mess is a bigger topic,
so let's jut punt on DDI for now.
Cc: Jani Nikula <jani.nikula@intel.com>
Fixes: 6fec766283 ("drm/i915: Use intel_dp->DP in eDP PLL setup")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463162036-27931-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
(cherry picked from commit 64989ca4b2)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 476490a945 upstream.
Thanks to Ville Syrjälä for pointing me towards the cause of this issue.
Unfortunately one of the sideaffects of having the refclk for a DPLL set
to SSC is that as long as it's set to SSC, the GPU will prevent us from
powering down any of the pipes or transcoders using it. A couple of
BIOSes enable SSC in both PCH_DREF_CONTROL and in the DPLL
configurations. This causes issues on the first modeset, since we don't
expect SSC to be left on and as a result, can't successfully power down
the pipes or the transcoders using it. Here's an example from this Dell
OptiPlex 990:
[drm:intel_modeset_init] SSC enabled by BIOS, overriding VBT which says disabled
[drm:intel_modeset_init] 2 display pipes available.
[drm:intel_update_cdclk] Current CD clock rate: 400000 kHz
[drm:intel_update_max_cdclk] Max CD clock rate: 400000 kHz
[drm:intel_update_max_cdclk] Max dotclock rate: 360000 kHz
vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[drm:intel_crt_reset] crt adpa set to 0xf40000
[drm:intel_dp_init_connector] Adding DP connector on port C
[drm:intel_dp_aux_init] registering DPDDC-C bus for card0-DP-1
[drm:ironlake_init_pch_refclk] has_panel 0 has_lvds 0 has_ck505 0
[drm:ironlake_init_pch_refclk] Disabling SSC entirely
… later we try committing the first modeset …
[drm:intel_dump_pipe_config] [CRTC:26][modeset] config ffff88041b02e800 for pipe A
[drm:intel_dump_pipe_config] cpu_transcoder: A
…
[drm:intel_dump_pipe_config] dpll_hw_state: dpll: 0xc4016001, dpll_md: 0x0, fp0: 0x20e08, fp1: 0x30d07
[drm:intel_dump_pipe_config] planes on this crtc
[drm:intel_dump_pipe_config] STANDARD PLANE:23 plane: 0.0 idx: 0 enabled
[drm:intel_dump_pipe_config] FB:42, fb = 800x600 format = 0x34325258
[drm:intel_dump_pipe_config] scaler:0 src (0, 0) 800x600 dst (0, 0) 800x600
[drm:intel_dump_pipe_config] CURSOR PLANE:25 plane: 0.1 idx: 1 disabled, scaler_id = 0
[drm:intel_dump_pipe_config] STANDARD PLANE:27 plane: 0.1 idx: 2 disabled, scaler_id = 0
[drm:intel_get_shared_dpll] CRTC:26 allocated PCH DPLL A
[drm:intel_get_shared_dpll] using PCH DPLL A for pipe A
[drm:ilk_audio_codec_disable] Disable audio codec on port C, pipe A
[drm:intel_disable_pipe] disabling pipe A
------------[ cut here ]------------
WARNING: CPU: 1 PID: 130 at drivers/gpu/drm/i915/intel_display.c:1146 intel_disable_pipe+0x297/0x2d0 [i915]
pipe_off wait timed out
…
---[ end trace 94fc8aa03ae139e8 ]---
[drm:intel_dp_link_down]
[drm:ironlake_crtc_disable [i915]] *ERROR* failed to disable transcoder A
Later modesets succeed since they reset the DPLL's configuration anyway,
but this is enough to get stuck with a big fat warning in dmesg.
A better solution would be to add refcounts for the SSC source, but for
now leaving the source clock on should suffice.
Changes since v4:
- Fix calculation of final for systems with LVDS panels (fixes BUG() on
CI test suite)
Changes since v3:
- Move temp variable into loop
- Move checks for using_ssc_source to after we've figured out has_ck505
- Add using_ssc_source to debug output
Changes since v2:
- Fix debug output for when we disable the CPU source
Changes since v1:
- Leave the SSC source clock on instead of just shutting it off on all
of the DPLL configurations.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Lyude <cpaul@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1465916649-10228-1-git-send-email-cpaul@redhat.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 217215041b upstream.
Fixes a regression caused by a stupid thinko from "disp/sor/gf119: both
links use the same training register".
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8953c52b9 upstream.
It appears that, for whatever reason, both link A and B use the same
register to control the training pattern. It's a little odd, as the
GPUs before this (Tesla/Fermi1) have per-link registers, as do newer
GPUs (Maxwell).
Fixes the third DP output on NVS 510 (GK107).
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fd2d2bac6e upstream.
Not clearing mst manager's proposed vcpis table for destroyed connectors when the manager is stopped leaves it pointing to unrefernced memory, this causes pagefault when the manager is restarted when plugging back a branch.
Fixes: 91a25e4631 ("drm/dp/mst: deallocate payload on port destruction")
Signed-off-by: Andrey Grodzovsky <Andrey.Grodzovsky@amd.com>
Reviewed-by: Lyude <cpaul@redhat.com>
Cc: Mykola Lysenko <Mykola.Lysenko@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bc4755a4bd upstream.
amdkfd need to destroy the debug manager in case amdkfd's notifier
function is called before the unbind function, because in that case,
the unbind function will exit without destroying debug manager.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 121b78e679 upstream.
When unbinding a process from a device (initiated by amd_iommu_v2), the
driver needs to make sure that process still exists in the process table.
There is a possibility that amdkfd's own notifier handler -
kfd_process_notifier_release() - was called before the unbind function
and it already removed the process from the process table.
v2:
Because there can be only one process with the specified pasid, and
because *p can't be NULL inside the hash_for_each_rcu macro, it is more
reasonable to just put the whole code inside the if statement that
compares the pasid value. That way, when we exit hash_for_each_rcu, we
simply exit the function as well.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 972228d874 upstream.
recover_peb() was never power cut aware,
if a power cut happened right after writing the VID header
upon next attach UBI would blindly use the new partial written
PEB and all data from the old PEB is lost.
In order to make recover_peb() power cut aware, write the new
VID with a proper crc and copy_flag set such that the UBI attach
process will detect whether the new PEB is completely written
or not.
We cannot directly use ubi_eba_atomic_leb_change() since we'd
have to unlock the LEB which is facing a write error.
Reported-by: Jörg Pfähler <pfaehler@isse.de>
Reviewed-by: Jörg Pfähler <pfaehler@isse.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 29b9c528b8 upstream.
amdgpu_cgs_acpi_eval_object() returned the value of variable "result"
without initializing it first.
This bug has been found by compiling the kernel with clang. The
compiler complained:
drivers/gpu/drm/amd/amdgpu/amdgpu_cgs.c:972:14: error: variable
'result' is used uninitialized whenever 'for' loop exits because its
condition is false [-Werror,-Wsometimes-uninitialized]
for (i = 0; i < count; i++) {
^~~~~~~~~
drivers/gpu/drm/amd/amdgpu/amdgpu_cgs.c:1011:9: note: uninitialized
use occurs here
return result;
^~~~~~
drivers/gpu/drm/amd/amdgpu/amdgpu_cgs.c:972:14: note: remove the
condition if it is always true
for (i = 0; i < count; i++) {
^~~~~~~~~
drivers/gpu/drm/amd/amdgpu/amdgpu_cgs.c:864:12: note: initialize the
variable 'result' to silence this warning
int result;
^
= 0
Fixes: 3f1d35a03b ("drm/amdgpu: implement new cgs interface for acpi
function")
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0b10029d82 upstream.
This was accidently broken for harvest cards when the
code was refactored for Polaris support.
v2: multiply by shader engines. Noticed by Nicolai.
Reviewed-by: Nicolai Hähnle <nicolai.haehnle@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05082b8bbd upstream.
When executing in a PCI passthrough based virtuzliation environment, the
hypervisor will usually attempt to send a PCIe bus reset signal to the
ASIC when the VM reboots. In this scenario, the card is not correctly
initialized, but we still consider it to be posted. Therefore, in a
passthrough based environemnt we should always post the card to guarantee
it is in a good state for driver initialization.
Ported from amdgpu commit:
amdgpu: fix asic initialization for virtualized environments
Cc: Andres Rodriguez <andres.rodriguez@amd.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 64c12921e1 upstream.
The test for !trans->blocks_used in btrfs_abort_transaction is
insufficient to determine whether it's safe to drop the transaction
handle on the floor. btrfs_cow_block, informed by should_cow_block,
can return blocks that have already been CoW'd in the current
transaction. trans->blocks_used is only incremented for new block
allocations. If an operation overlaps the blocks in the current
transaction entirely and must abort the transaction, we'll happily
let it clean up the trans handle even though it may have modified
the blocks and will commit an incomplete operation.
In the long-term, I'd like to do closer tracking of when the fs
is actually modified so we can still recover as gracefully as possible,
but that approach will need some discussion. In the short term,
since this is the only code using trans->blocks_used, let's just
switch it to a bool indicating whether any blocks were used and set
it when should_cow_block returns false.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6710e594f7 upstream.
For non-atomic allocations, pcpu_alloc() can try to extend the area
map synchronously after dropping pcpu_lock; however, the extension
wasn't synchronized against chunk destruction and the chunk might get
freed while extension is in progress.
This patch fixes the bug by putting most of non-atomic allocations
under pcpu_alloc_mutex to synchronize against pcpu_balance_work which
is responsible for async chunk management including destruction.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-and-tested-by: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Reported-by: Vlastimil Babka <vbabka@suse.cz>
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Fixes: 1a4d76076c ("percpu: implement asynchronous chunk population")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f996e234d upstream.
Atomic allocations can trigger async map extensions which is serviced
by chunk->map_extend_work. pcpu_balance_work which is responsible for
destroying idle chunks wasn't synchronizing properly against
chunk->map_extend_work and may end up freeing the chunk while the work
item is still in flight.
This patch fixes the bug by rolling async map extension operations
into pcpu_balance_work.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-and-tested-by: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Reported-by: Vlastimil Babka <vbabka@suse.cz>
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Fixes: 9c824b6a17 ("percpu: make sure chunk->map array has available space")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eb0a4a47ae upstream.
Overlayfs uses separate inodes even in the case of hard links on the
underlying filesystems. This is a problem for AF_UNIX socket
implementation which indexes sockets based on the inode. This resulted in
hard linked sockets not working.
The fix is to use the real, underlying inode.
Test case follows:
-- ovl-sock-test.c --
#include <unistd.h>
#include <err.h>
#include <sys/socket.h>
#include <sys/un.h>
#define SOCK "test-sock"
#define SOCK2 "test-sock2"
int main(void)
{
int fd, fd2;
struct sockaddr_un addr = {
.sun_family = AF_UNIX,
.sun_path = SOCK,
};
struct sockaddr_un addr2 = {
.sun_family = AF_UNIX,
.sun_path = SOCK2,
};
unlink(SOCK);
unlink(SOCK2);
if ((fd = socket(AF_UNIX, SOCK_STREAM, 0)) == -1)
err(1, "socket");
if (bind(fd, (struct sockaddr *) &addr, sizeof(addr)) == -1)
err(1, "bind");
if (listen(fd, 0) == -1)
err(1, "listen");
if (link(SOCK, SOCK2) == -1)
err(1, "link");
if ((fd2 = socket(AF_UNIX, SOCK_STREAM, 0)) == -1)
err(1, "socket");
if (connect(fd2, (struct sockaddr *) &addr2, sizeof(addr2)) == -1)
err (1, "connect");
return 0;
}
----
Reported-by: Alexander Morozov <alexandr.morozov@docker.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e19a6ee246 upstream.
If we take an exception while at EL1, the exception handler inherits
the original context's addr_limit and PSTATE.UAO values. To be consistent
always reset addr_limit and PSTATE.UAO on (re-)entry to EL1. This
prevents accidental re-use of the original context's addr_limit.
Based on a similar patch for arm from Russell King.
Acked-by: Will Deacon <will.deacon@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 20c27a4270 upstream.
__sync_icache_dcache unconditionally skips the cache maintenance for
anonymous pages, under the assumption that flushing is only required in
the presence of D-side aliases [see 7249b79f6b ("arm64: Do not flush
the D-cache for anonymous pages")].
Unfortunately, this breaks migration of anonymous pages holding
self-modifying code, where userspace cannot be reasonably expected to
reissue maintenance instructions in response to a migration.
This patch fixes the problem by removing the broken page_mapping(page)
check from the cache syncing code, otherwise we may end up fetching and
executing stale instructions from the PoU.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c5cea06be0 upstream.
If the kernel is set to show unhandled signals, and a user task does not
handle a SIGILL as a result of an instruction abort, we will attempt to
log the offending instruction with dump_instr before killing the task.
We use dump_instr to log the encoding of the offending userspace
instruction. However, dump_instr is also used to dump instructions from
kernel space, and internally always switches to KERNEL_DS before dumping
the instruction with get_user. When both PAN and UAO are in use, reading
a user instruction via get_user while in KERNEL_DS will result in a
permission fault, which leads to an Oops.
As we have regs corresponding to the context of the original instruction
abort, we can inspect this and only flip to KERNEL_DS if the original
abort was taken from the kernel, avoiding this issue. At the same time,
remove the redundant (and incorrect) comments regarding the order
dump_mem and dump_instr are called in.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reported-by: Vladimir Murzin <vladimir.murzin@arm.com>
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com>
Fixes: 57f4959bad ("arm64: kernel: Add support for User Access Override")
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ae4ea9a246 upstream.
Commit 7ea0ed2b5b ("ipmi: Make the message handler easier to use for
SMI interfaces") changed handle_new_recv_msgs() to call handle_one_recv_msg()
for a smi_msg while the smi_msg is still connected to waiting_rcv_msgs list.
That could lead to following list corruption problems:
1) low-level function treats smi_msg as not connected to list
handle_one_recv_msg() could end up calling smi_send(), which
assumes the msg is not connected to list.
For example, the following sequence could corrupt list by
doing list_add_tail() for the entry still connected to other list.
handle_new_recv_msgs()
msg = list_entry(waiting_rcv_msgs)
handle_one_recv_msg(msg)
handle_ipmb_get_msg_cmd(msg)
smi_send(msg)
spin_lock(xmit_msgs_lock)
list_add_tail(msg)
spin_unlock(xmit_msgs_lock)
2) race between multiple handle_new_recv_msgs() instances
handle_new_recv_msgs() once releases waiting_rcv_msgs_lock before calling
handle_one_recv_msg() then retakes the lock and list_del() it.
If others call handle_new_recv_msgs() during the window shown below
list_del() will be done twice for the same smi_msg.
handle_new_recv_msgs()
spin_lock(waiting_rcv_msgs_lock)
msg = list_entry(waiting_rcv_msgs)
spin_unlock(waiting_rcv_msgs_lock)
|
| handle_one_recv_msg(msg)
|
spin_lock(waiting_rcv_msgs_lock)
list_del(msg)
spin_unlock(waiting_rcv_msgs_lock)
Fixes: 7ea0ed2b5b ("ipmi: Make the message handler easier to use for SMI interfaces")
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
[Added a comment to describe why this works.]
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Tested-by: Ye Feng <yefeng.yl@alibaba-inc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce492b3b8f upstream.
Using flat regmap cache instead of RB-tree to avoid the following
lockdep warning on driver load:
WARNING: CPU: 0 PID: 1 at kernel/locking/lockdep.c:2755 lockdep_trace_alloc+0x15c/0x160()
DEBUG_LOCKS_WARN_ON(irqs_disabled_flags(flags))
The RB-tree regmap cache needs to allocate new space on first
writes. However, allocations in an atomic context (e.g. when a
spinlock is held) are not allowed. The function regmap_write
calls map->lock, which acquires a spinlock in the fast_io case.
Since the FSL DCU driver uses MMIO, the regmap bus of type
regmap_mmio is being used which has fast_io set to true.
Use flat regmap cache and specify max register to be large
enouth to cover all registers available in LS1021a and Vybrids
register space.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 522e5cb76d upstream.
There is a race condition in the AMD IOMMU init code that
causes requested unity mappings to be blocked by the IOMMU
for a short period of time. This results on boot failures
and IO_PAGE_FAULTs on some machines.
Fix this by making sure the unity mappings are installed
before all other DMA is blocked.
Fixes: aafd8ba0ca ('iommu/amd: Implement add_device and remove_device')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a4c34ff1c0 upstream.
This seems to be required on some X58 chipsets on systems
with more than one IOMMU. QI does not work until it is
enabled on all IOMMUs in the system.
Reported-by: Dheeraj CVR <cvr.dheeraj@gmail.com>
Tested-by: Dheeraj CVR <cvr.dheeraj@gmail.com>
Fixes: 5f0a7f7614 ('iommu/vt-d: Make root entry visible for hardware right after allocation')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9aeb26cfc2 upstream.
The map_sg callback is missing from arm_smmu_ops, but is required by
iommu.h. Similarly to most other IOMMU drivers, connect it to
default_iommu_map_sg.
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ae8a7910fb upstream.
rk_iommu_command() takes a struct rk_iommu and iterates over the slave
MMUs, so this is doubly wrong in that we're passing in the wrong pointer
and talking to MMUs that we shouldn't be.
Fixes: cd6438c5f8 ("iommu/rockchip: Reconstruct to support multi slaves")
Signed-off-by: John Keeping <john@metanate.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e1b1fc4da upstream.
Modules which register drivers via standard path (driver_register) in
parallel can cause a warning:
WARNING: CPU: 2 PID: 3492 at ../fs/sysfs/dir.c:31 sysfs_warn_dup+0x62/0x80
sysfs: cannot create duplicate filename '/module/saa7146/drivers'
Modules linked in: hexium_gemini(+) mxb(+) ...
...
Call Trace:
...
[<ffffffff812e63a2>] sysfs_warn_dup+0x62/0x80
[<ffffffff812e6487>] sysfs_create_dir_ns+0x77/0x90
[<ffffffff8140f2c4>] kobject_add_internal+0xb4/0x340
[<ffffffff8140f5b8>] kobject_add+0x68/0xb0
[<ffffffff8140f631>] kobject_create_and_add+0x31/0x70
[<ffffffff8157a703>] module_add_driver+0xc3/0xd0
[<ffffffff8155e5d4>] bus_add_driver+0x154/0x280
[<ffffffff815604c0>] driver_register+0x60/0xe0
[<ffffffff8145bed0>] __pci_register_driver+0x60/0x70
[<ffffffffa0273e14>] saa7146_register_extension+0x64/0x90 [saa7146]
[<ffffffffa0033011>] hexium_init_module+0x11/0x1000 [hexium_gemini]
...
As can be (mostly) seen, driver_register causes this call sequence:
-> bus_add_driver
-> module_add_driver
-> module_create_drivers_dir
The last one creates "drivers" directory in /sys/module/<...>. When
this is done in parallel, the directory is attempted to be created
twice at the same time.
This can be easily reproduced by loading mxb and hexium_gemini in
parallel:
while :; do
modprobe mxb &
modprobe hexium_gemini
wait
rmmod mxb hexium_gemini saa7146_vv saa7146
done
saa7146 calls pci_register_driver for both mxb and hexium_gemini,
which means /sys/module/saa7146/drivers is to be created for both of
them.
Fix this by a new mutex in module_create_drivers_dir which makes the
test-and-create "drivers" dir atomic.
I inverted the condition and removed 'return' to avoid multiple
unlocks or a goto.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Fixes: fe480a2675 (Modules: only add drivers/ direcory if needed)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 70c8217acd upstream.
If a task uses a non constant string for the format parameter in
trace_printk(), then the trace_printk_fmt variable is set to NULL. This
variable is then saved in the __trace_printk_fmt section.
The function hold_module_trace_bprintk_format() checks to see if duplicate
formats are used by modules, and reuses them if so (saves them to the list
if it is new). But this function calls lookup_format() that does a strcmp()
to the value (which is now NULL) and can cause a kernel oops.
This wasn't an issue till 3debb0a9dd ("tracing: Fix trace_printk() to print
when not using bprintk()") which added "__used" to the trace_printk_fmt
variable, and before that, the kernel simply optimized it out (no NULL value
was saved).
The fix is simply to handle the NULL pointer in lookup_format() and have the
caller ignore the value if it was NULL.
Link: http://lkml.kernel.org/r/1464769870-18344-1-git-send-email-zhengjun.xing@intel.com
Reported-by: xingzhen <zhengjun.xing@intel.com>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Fixes: 3debb0a9dd ("tracing: Fix trace_printk() to print when not using bprintk()")
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6dd2e27a10 upstream.
The usage Confidence is mandary to Windows Precision Touchpad devices. If
it is examined in input_mapping on a WIndows Precision Touchpad, a new add
quirk MT_QUIRK_CONFIDENCE desgned for such devices will be applied to the
device. A touch with the confidence bit is not set is determined as
invalid.
Tested on Dell XPS13 9343
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Andy Lutomirski <luto@kernel.org> # XPS 13 9350, BIOS 1.4.3
Signed-off-by: Allen Hung <allen_hung@dell.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 62630ea768 upstream.
This reverts commit 25a84db15b ("HID: multitouch: enable palm rejection
if device implements confidence usage")
The commit enables palm rejection for Win8 Precision Touchpad devices but
the quirk MT_QUIRK_VALID_IS_CONFIDENCE it is using is not working very
properly. This quirk is originally designed for some WIn7 touchscreens. Use
of this for a Win8 Precision Touchpad will cause unexpected pointer jumping
problem.
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Andy Lutomirski <luto@kernel.org> # XPS 13 9350, BIOS 1.4.3
Signed-off-by: Allen Hung <allen_hung@dell.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 93a2001bdf upstream.
This patch validates the num_values parameter from userland during the
HIDIOCGUSAGES and HIDIOCSUSAGES commands. Previously, if the report id was set
to HID_REPORT_ID_UNKNOWN, we would fail to validate the num_values parameter
leading to a heap overflow.
Signed-off-by: Scott Bauer <sbauer@plzdonthack.me>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ed596a4a88 upstream.
Flushing a work that reschedules itself is not a sensible operation. It needs
to be killed. Failure to do so leads to a kernel panic in the timer code.
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff30ef40de upstream.
I couldn't get Xen to boot a L2 HVM when it was nested under KVM - it was
getting a GP(0) on a rather unspecial vmread from Xen:
(XEN) ----[ Xen-4.7.0-rc x86_64 debug=n Not tainted ]----
(XEN) CPU: 1
(XEN) RIP: e008:[<ffff82d0801e629e>] vmx_get_segment_register+0x14e/0x450
(XEN) RFLAGS: 0000000000010202 CONTEXT: hypervisor (d1v0)
(XEN) rax: ffff82d0801e6288 rbx: ffff83003ffbfb7c rcx: fffffffffffab928
(XEN) rdx: 0000000000000000 rsi: 0000000000000000 rdi: ffff83000bdd0000
(XEN) rbp: ffff83000bdd0000 rsp: ffff83003ffbfab0 r8: ffff830038813910
(XEN) r9: ffff83003faf3958 r10: 0000000a3b9f7640 r11: ffff83003f82d418
(XEN) r12: 0000000000000000 r13: ffff83003ffbffff r14: 0000000000004802
(XEN) r15: 0000000000000008 cr0: 0000000080050033 cr4: 00000000001526e0
(XEN) cr3: 000000003fc79000 cr2: 0000000000000000
(XEN) ds: 0000 es: 0000 fs: 0000 gs: 0000 ss: 0000 cs: e008
(XEN) Xen code around <ffff82d0801e629e> (vmx_get_segment_register+0x14e/0x450):
(XEN) 00 00 41 be 02 48 00 00 <44> 0f 78 74 24 08 0f 86 38 56 00 00 b8 08 68 00
(XEN) Xen stack trace from rsp=ffff83003ffbfab0:
...
(XEN) Xen call trace:
(XEN) [<ffff82d0801e629e>] vmx_get_segment_register+0x14e/0x450
(XEN) [<ffff82d0801f3695>] get_page_from_gfn_p2m+0x165/0x300
(XEN) [<ffff82d0801bfe32>] hvmemul_get_seg_reg+0x52/0x60
(XEN) [<ffff82d0801bfe93>] hvm_emulate_prepare+0x53/0x70
(XEN) [<ffff82d0801ccacb>] handle_mmio+0x2b/0xd0
(XEN) [<ffff82d0801be591>] emulate.c#_hvm_emulate_one+0x111/0x2c0
(XEN) [<ffff82d0801cd6a4>] handle_hvm_io_completion+0x274/0x2a0
(XEN) [<ffff82d0801f334a>] __get_gfn_type_access+0xfa/0x270
(XEN) [<ffff82d08012f3bb>] timer.c#add_entry+0x4b/0xb0
(XEN) [<ffff82d08012f80c>] timer.c#remove_entry+0x7c/0x90
(XEN) [<ffff82d0801c8433>] hvm_do_resume+0x23/0x140
(XEN) [<ffff82d0801e4fe7>] vmx_do_resume+0xa7/0x140
(XEN) [<ffff82d080164aeb>] context_switch+0x13b/0xe40
(XEN) [<ffff82d080128e6e>] schedule.c#schedule+0x22e/0x570
(XEN) [<ffff82d08012c0cc>] softirq.c#__do_softirq+0x5c/0x90
(XEN) [<ffff82d0801602c5>] domain.c#idle_loop+0x25/0x50
(XEN)
(XEN)
(XEN) ****************************************
(XEN) Panic on CPU 1:
(XEN) GENERAL PROTECTION FAULT
(XEN) [error_code=0000]
(XEN) ****************************************
Tracing my host KVM showed it was the one injecting the GP(0) when
emulating the VMREAD and checking the destination segment permissions in
get_vmx_mem_address():
3) | vmx_handle_exit() {
3) | handle_vmread() {
3) | nested_vmx_check_permission() {
3) | vmx_get_segment() {
3) 0.074 us | vmx_read_guest_seg_base();
3) 0.065 us | vmx_read_guest_seg_selector();
3) 0.066 us | vmx_read_guest_seg_ar();
3) 1.636 us | }
3) 0.058 us | vmx_get_rflags();
3) 0.062 us | vmx_read_guest_seg_ar();
3) 3.469 us | }
3) | vmx_get_cs_db_l_bits() {
3) 0.058 us | vmx_read_guest_seg_ar();
3) 0.662 us | }
3) | get_vmx_mem_address() {
3) 0.068 us | vmx_cache_reg();
3) | vmx_get_segment() {
3) 0.074 us | vmx_read_guest_seg_base();
3) 0.068 us | vmx_read_guest_seg_selector();
3) 0.071 us | vmx_read_guest_seg_ar();
3) 1.756 us | }
3) | kvm_queue_exception_e() {
3) 0.066 us | kvm_multiple_exception();
3) 0.684 us | }
3) 4.085 us | }
3) 9.833 us | }
3) + 10.366 us | }
Cross-checking the KVM/VMX VMREAD emulation code with the Intel Software
Developper Manual Volume 3C - "VMREAD - Read Field from Virtual-Machine
Control Structure", I found that we're enforcing that the destination
operand is NOT located in a read-only data segment or any code segment when
the L1 is in long mode - BUT that check should only happen when it is in
protected mode.
Shuffling the code a bit to make our emulation follow the specification
allows me to boot a Xen dom0 in a nested KVM and start HVM L2 guests
without problems.
Fixes: f9eb4af67c ("KVM: nVMX: VMX instructions: add checks for #GP/#SS exceptions")
Signed-off-by: Quentin Casasnovas <quentin.casasnovas@oracle.com>
Cc: Eugene Korenevsky <ekorenevsky@gmail.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 591d215afc upstream.
kvm provides kvm_vcpu_uninit(), which amongst other things, releases the
last reference to the struct pid of the task that was last running the vcpu.
On arm64 built with CONFIG_DEBUG_KMEMLEAK, starting a guest with kvmtool,
then killing it with SIGKILL results (after some considerable time) in:
> cat /sys/kernel/debug/kmemleak
> unreferenced object 0xffff80007d5ea080 (size 128):
> comm "lkvm", pid 2025, jiffies 4294942645 (age 1107.776s)
> hex dump (first 32 bytes):
> 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
> 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
> backtrace:
> [<ffff8000001b30ec>] create_object+0xfc/0x278
> [<ffff80000071da34>] kmemleak_alloc+0x34/0x70
> [<ffff80000019fa2c>] kmem_cache_alloc+0x16c/0x1d8
> [<ffff8000000d0474>] alloc_pid+0x34/0x4d0
> [<ffff8000000b5674>] copy_process.isra.6+0x79c/0x1338
> [<ffff8000000b633c>] _do_fork+0x74/0x320
> [<ffff8000000b66b0>] SyS_clone+0x18/0x20
> [<ffff800000085cb0>] el0_svc_naked+0x24/0x28
> [<ffffffffffffffff>] 0xffffffffffffffff
On x86 kvm_vcpu_uninit() is called on the path from kvm_arch_destroy_vm(),
on arm no equivalent call is made. Add the call to kvm_arch_vcpu_free().
Signed-off-by: James Morse <james.morse@arm.com>
Fixes: 749cf76c5a ("KVM: ARM: Initial skeleton to compile KVM support")
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c343f7b0e upstream.
commit 1e133ab296 ("s390/mm: split arch/s390/mm/pgtable.c") factored
out the page table handling code from __gmap_zap and __s390_reset_cmma
into ptep_zap_unused and added a simple flag that tells which one of the
function (reset or not) is to be made. This also changed the behaviour,
as it also zaps unused page table entries on reset.
Turns out that this is wrong as s390_reset_cmma uses the page walker,
which DOES NOT take the ptl lock.
The most simple fix is to not do the zapping part on reset (which uses
the walker)
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Fixes: 1e133ab296 ("s390/mm: split arch/s390/mm/pgtable.c")
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit caf1ff26e1 upstream.
These days, we experienced one guest crash with 8 cores and 3 disks,
with qemu error logs as bellow:
qemu-system-x86_64: /build/qemu-2.0.0/kvm-all.c:984:
kvm_irqchip_commit_routes: Assertion `ret == 0' failed.
And then we found one patch(bdf026317d) in qemu tree, which said
could fix this bug.
Execute the following script will reproduce the BUG quickly:
irq_affinity.sh
========================================================================
vda_irq_num=25
vdb_irq_num=27
while [ 1 ]
do
for irq in {1,2,4,8,10,20,40,80}
do
echo $irq > /proc/irq/$vda_irq_num/smp_affinity
echo $irq > /proc/irq/$vdb_irq_num/smp_affinity
dd if=/dev/vda of=/dev/zero bs=4K count=100 iflag=direct
dd if=/dev/vdb of=/dev/zero bs=4K count=100 iflag=direct
done
done
========================================================================
The following qemu log is added in the qemu code and is displayed when
this bug reproduced:
kvm_irqchip_commit_routes: max gsi: 1008, nr_allocated_irq_routes: 1024,
irq_routes->nr: 1024, gsi_count: 1024.
That's to say when irq_routes->nr == 1024, there are 1024 routing entries,
but in the kernel code when routes->nr >= 1024, will just return -EINVAL;
The nr is the number of the routing entries which is in of
[1 ~ KVM_MAX_IRQ_ROUTES], not the index in [0 ~ KVM_MAX_IRQ_ROUTES - 1].
This patch fix the BUG above.
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Wei Tang <tangwei@cmss.chinamobile.com>
Signed-off-by: Zhang Zhuoyu <zhangzhuoyu@cmss.chinamobile.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 38327424b4 upstream.
If __key_link_begin() failed then "edit" would be uninitialized. I've
added a check to fix that.
This allows a random user to crash the kernel, though it's quite
difficult to achieve. There are three ways it can be done as the user
would have to cause an error to occur in __key_link():
(1) Cause the kernel to run out of memory. In practice, this is difficult
to achieve without ENOMEM cropping up elsewhere and aborting the
attempt.
(2) Revoke the destination keyring between the keyring ID being looked up
and it being tested for revocation. In practice, this is difficult to
time correctly because the KEYCTL_REJECT function can only be used
from the request-key upcall process. Further, users can only make use
of what's in /sbin/request-key.conf, though this does including a
rejection debugging test - which means that the destination keyring
has to be the caller's session keyring in practice.
(3) Have just enough key quota available to create a key, a new session
keyring for the upcall and a link in the session keyring, but not then
sufficient quota to create a link in the nominated destination keyring
so that it fails with EDQUOT.
The bug can be triggered using option (3) above using something like the
following:
echo 80 >/proc/sys/kernel/keys/root_maxbytes
keyctl request2 user debug:fred negate @t
The above sets the quota to something much lower (80) to make the bug
easier to trigger, but this is dependent on the system. Note also that
the name of the keyring created contains a random number that may be
between 1 and 10 characters in size, so may throw the test off by
changing the amount of quota used.
Assuming the failure occurs, something like the following will be seen:
kfree_debugcheck: out of range ptr 6b6b6b6b6b6b6b68h
------------[ cut here ]------------
kernel BUG at ../mm/slab.c:2821!
...
RIP: 0010:[<ffffffff811600f9>] kfree_debugcheck+0x20/0x25
RSP: 0018:ffff8804014a7de8 EFLAGS: 00010092
RAX: 0000000000000034 RBX: 6b6b6b6b6b6b6b68 RCX: 0000000000000000
RDX: 0000000000040001 RSI: 00000000000000f6 RDI: 0000000000000300
RBP: ffff8804014a7df0 R08: 0000000000000001 R09: 0000000000000000
R10: ffff8804014a7e68 R11: 0000000000000054 R12: 0000000000000202
R13: ffffffff81318a66 R14: 0000000000000000 R15: 0000000000000001
...
Call Trace:
kfree+0xde/0x1bc
assoc_array_cancel_edit+0x1f/0x36
__key_link_end+0x55/0x63
key_reject_and_link+0x124/0x155
keyctl_reject_key+0xb6/0xe0
keyctl_negate_key+0x10/0x12
SyS_keyctl+0x9f/0xe7
do_syscall_64+0x63/0x13a
entry_SYSCALL64_slow_path+0x25/0x25
Fixes: f70e2e0619 ('KEYS: Do preallocation for __key_link()')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 903ce4abdf ]
It was first reported and reproduced by Petr (thanks!) in
https://bugzilla.kernel.org/show_bug.cgi?id=119581
free_percpu(rt->rt6i_pcpu) used to always happen in ip6_dst_destroy().
However, after fixing a deadlock bug in
commit 9c7370a166 ("ipv6: Fix a potential deadlock when creating pcpu rt"),
free_percpu() is not called before setting non_pcpu_rt->rt6i_pcpu to NULL.
It is worth to note that rt6i_pcpu is protected by table->tb6_lock.
kmemleak somehow did not report it. We nailed it down by
observing the pcpu entries in /proc/vmallocinfo (first suggested
by Hannes, thanks!).
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Fixes: 9c7370a166 ("ipv6: Fix a potential deadlock when creating pcpu rt")
Reported-by: Petr Novopashenniy <pety@rusnet.ru>
Tested-by: Petr Novopashenniy <pety@rusnet.ru>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Petr Novopashenniy <pety@rusnet.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c086e70961 ]
Several Lenovo users have reported problems with their Sierra
Wireless EM7455 modem. The driver has loaded successfully and
the MBIM management channel has appeared to work, including
establishing a connection to the mobile network. But no frames
have been received over the data interface.
The problem affects all EM7455 and MC7455, and is assumed to
affect other modems based on the same Qualcomm chipset and
baseband firmware.
Testing narrowed the problem down to what seems to be a
firmware timing bug during initialization. Adding a short sleep
while probing is sufficient to make the problem disappear.
Experiments have shown that 1-2 ms is too little to have any
effect, while 10-20 ms is enough to reliably succeed.
Reported-by: Stefan Armbruster <ml001@armbruster-it.de>
Reported-by: Ralph Plawetzki <ralph@purejava.org>
Reported-by: Andreas Fett <andreas.fett@secunet.com>
Reported-by: Rasmus Lerdorf <rasmus@lerdorf.com>
Reported-by: Samo Ratnik <samo.ratnik@gmail.com>
Reported-and-tested-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 79c62220d7 ]
Avoid recursions of dev_queue_xmit() to the wrong net device when
frames are unprotected, since at that time skb->dev still points to
our own macsec dev and unlike macsec_encrypt_finish() dev pointer
doesn't get updated to real underlying device.
Fixes: c09440f7dc ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit eb70db8756 ]
People who use PACKET_FANOUT_HASH want a symmetric hash, meaning that
they want packets going in both directions on a flow to hash to the
same bucket.
The core kernel SKB hash became non-symmetric when the ipv6 flow label
and other entities were incorporated into the standard flow hash order
to increase entropy.
But there are no users of PACKET_FANOUT_HASH who want an assymetric
hash, they all want a symmetric one.
Therefore, use the flow dissector to compute a flat symmetric hash
over only the protocol, addresses and ports. This hash does not get
installed into and override the normal skb hash, so this change has
no effect whatsoever on the rest of the stack.
Reported-by: Eric Leblond <eric@regit.org>
Tested-by: Eric Leblond <eric@regit.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8974189222 upstream.
As per commit:
b7fa30c9cc ("sched/fair: Fix post_init_entity_util_avg() serialization")
> the code generated from update_cfs_rq_load_avg():
>
> if (atomic_long_read(&cfs_rq->removed_load_avg)) {
> s64 r = atomic_long_xchg(&cfs_rq->removed_load_avg, 0);
> sa->load_avg = max_t(long, sa->load_avg - r, 0);
> sa->load_sum = max_t(s64, sa->load_sum - r * LOAD_AVG_MAX, 0);
> removed_load = 1;
> }
>
> turns into:
>
> ffffffff81087064: 49 8b 85 98 00 00 00 mov 0x98(%r13),%rax
> ffffffff8108706b: 48 85 c0 test %rax,%rax
> ffffffff8108706e: 74 40 je ffffffff810870b0 <update_blocked_averages+0xc0>
> ffffffff81087070: 4c 89 f8 mov %r15,%rax
> ffffffff81087073: 49 87 85 98 00 00 00 xchg %rax,0x98(%r13)
> ffffffff8108707a: 49 29 45 70 sub %rax,0x70(%r13)
> ffffffff8108707e: 4c 89 f9 mov %r15,%rcx
> ffffffff81087081: bb 01 00 00 00 mov $0x1,%ebx
> ffffffff81087086: 49 83 7d 70 00 cmpq $0x0,0x70(%r13)
> ffffffff8108708b: 49 0f 49 4d 70 cmovns 0x70(%r13),%rcx
>
> Which you'll note ends up with sa->load_avg -= r in memory at
> ffffffff8108707a.
So I _should_ have looked at other unserialized users of ->load_avg,
but alas. Luckily nikbor reported a similar /0 from task_h_load() which
instantly triggered recollection of this here problem.
Aside from the intermediate value hitting memory and causing problems,
there's another problem: the underflow detection relies on the signed
bit. This reduces the effective width of the variables, IOW its
effectively the same as having these variables be of signed type.
This patch changes to a different means of unsigned underflow
detection to not rely on the signed bit. This allows the variables to
use the 'full' unsigned range. And it does so with explicit LOAD -
STORE to ensure any intermediate value will never be visible in
memory, allowing these unserialized loads.
Note: GCC generates crap code for this, might warrant a look later.
Note2: I say 'full' above, if we end up at U*_MAX we'll still explode;
maybe we should do clamping on add too.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yuyang Du <yuyang.du@intel.com>
Cc: bsegall@google.com
Cc: kernel@kyup.com
Cc: morten.rasmussen@arm.com
Cc: pjt@google.com
Cc: steve.muckle@linaro.org
Fixes: 9d89c257df ("sched/fair: Rewrite runnable load and utilization average tracking")
Link: http://lkml.kernel.org/r/20160617091948.GJ30927@twins.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4ac1c17b20 upstream.
During page migrations UBIFS might get confused
and the following assert triggers:
[ 213.480000] UBIFS assert failed in ubifs_set_page_dirty at 1451 (pid 436)
[ 213.490000] CPU: 0 PID: 436 Comm: drm-stress-test Not tainted 4.4.4-00176-geaa802524636-dirty #1008
[ 213.490000] Hardware name: Allwinner sun4i/sun5i Families
[ 213.490000] [<c0015e70>] (unwind_backtrace) from [<c0012cdc>] (show_stack+0x10/0x14)
[ 213.490000] [<c0012cdc>] (show_stack) from [<c02ad834>] (dump_stack+0x8c/0xa0)
[ 213.490000] [<c02ad834>] (dump_stack) from [<c0236ee8>] (ubifs_set_page_dirty+0x44/0x50)
[ 213.490000] [<c0236ee8>] (ubifs_set_page_dirty) from [<c00fa0bc>] (try_to_unmap_one+0x10c/0x3a8)
[ 213.490000] [<c00fa0bc>] (try_to_unmap_one) from [<c00fadb4>] (rmap_walk+0xb4/0x290)
[ 213.490000] [<c00fadb4>] (rmap_walk) from [<c00fb1bc>] (try_to_unmap+0x64/0x80)
[ 213.490000] [<c00fb1bc>] (try_to_unmap) from [<c010dc28>] (migrate_pages+0x328/0x7a0)
[ 213.490000] [<c010dc28>] (migrate_pages) from [<c00d0cb0>] (alloc_contig_range+0x168/0x2f4)
[ 213.490000] [<c00d0cb0>] (alloc_contig_range) from [<c010ec00>] (cma_alloc+0x170/0x2c0)
[ 213.490000] [<c010ec00>] (cma_alloc) from [<c001a958>] (__alloc_from_contiguous+0x38/0xd8)
[ 213.490000] [<c001a958>] (__alloc_from_contiguous) from [<c001ad44>] (__dma_alloc+0x23c/0x274)
[ 213.490000] [<c001ad44>] (__dma_alloc) from [<c001ae08>] (arm_dma_alloc+0x54/0x5c)
[ 213.490000] [<c001ae08>] (arm_dma_alloc) from [<c035cecc>] (drm_gem_cma_create+0xb8/0xf0)
[ 213.490000] [<c035cecc>] (drm_gem_cma_create) from [<c035cf20>] (drm_gem_cma_create_with_handle+0x1c/0xe8)
[ 213.490000] [<c035cf20>] (drm_gem_cma_create_with_handle) from [<c035d088>] (drm_gem_cma_dumb_create+0x3c/0x48)
[ 213.490000] [<c035d088>] (drm_gem_cma_dumb_create) from [<c0341ed8>] (drm_ioctl+0x12c/0x444)
[ 213.490000] [<c0341ed8>] (drm_ioctl) from [<c0121adc>] (do_vfs_ioctl+0x3f4/0x614)
[ 213.490000] [<c0121adc>] (do_vfs_ioctl) from [<c0121d30>] (SyS_ioctl+0x34/0x5c)
[ 213.490000] [<c0121d30>] (SyS_ioctl) from [<c000f2c0>] (ret_fast_syscall+0x0/0x34)
UBIFS is using PagePrivate() which can have different meanings across
filesystems. Therefore the generic page migration code cannot handle this
case correctly.
We have to implement our own migration function which basically does a
plain copy but also duplicates the page private flag.
UBIFS is not a block device filesystem and cannot use buffer_migrate_page().
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
[rw: Massaged changelog, build fixes, etc...]
Signed-off-by: Richard Weinberger <richard@nod.at>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1118dce773 upstream.
Export these symbols such that UBIFS can implement
->migratepage.
Signed-off-by: Richard Weinberger <richard@nod.at>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4b2312bd05 upstream.
When allocating a new device IRQ, gic_dev_domain_alloc() correctly calls
irq_domain_set_hwirq_and_chip(), but gic_irq_domain_alloc() does not. This
means that gic_irq_domain believes all IRQs from the dev domain have an
hwirq of 0 and creates incorrect mappings in the linear_revmap. As
gic_irq_domain is a parent of the gic_dev_domain, this leads to an
inability to boot on devices with a GIC. Excerpt of the error:
[ 2.297649] irq 0: nobody cared (try booting with the "irqpoll" option)
...
[ 2.436963] handlers:
[ 2.439492] Disabling IRQ #0
Fix this by calling irq_domain_set_hwirq_and_chip() for both the dev and
irq domain.
Now that we are modifying the parent domain, be sure to clear it up in
case of an allocation error.
Fixes: c98c1822ee ("irqchip/mips-gic: Add device hierarchy domain")
Fixes: 2af70a9620 ("irqchip/mips-gic: Add a IPI hierarchy domain")
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Tested-by: Govindraj Raja <Govindraj.Raja@imgtec.com> # On Pistachio SoC
Reviewed-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Qais Yousef <qsyousef@gmail.com>
Cc: jason@lakedaemon.net
Cc: marc.zyngier@arm.com
Link: http://lkml.kernel.org/r/1464001552-31174-1-git-send-email-harvey.hunt@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 797179bc4f upstream.
Copy __kvm_mips_vcpu_run() into unmapped memory, so that we can never
get a TLB refill exception in it when KVM is built as a module.
This was observed to happen with the host MIPS kernel running under
QEMU, due to a not entirely transparent optimisation in the QEMU TLB
handling where TLB entries replaced with TLBWR are copied to a separate
part of the TLB array. Code in those pages continue to be executable,
but those mappings persist only until the next ASID switch, even if they
are marked global.
An ASID switch happens in __kvm_mips_vcpu_run() at exception level after
switching to the guest exception base. Subsequent TLB mapped kernel
instructions just prior to switching to the guest trigger a TLB refill
exception, which enters the guest exception handlers without updating
EPC. This appears as a guest triggered TLB refill on a host kernel
mapped (host KSeg2) address, which is not handled correctly as user
(guest) mode accesses to kernel (host) segments always generate address
error exceptions.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cb84f6c0a2 upstream.
This is the same issue fixed in commit dcf5341f01 ("ARM: dts:
sun8i-q8-common: Do not set constraints on dc1sw regulator").
Commit message copied:
dc1sw is an on/off only regulator and as such it cannot have constraints.
This is a limitation of the kernel regulator implementation which resolves
supplies on the first regulator_get(), which is done after applying
constraints, and applying the constrains will fail because it calls
_regulator_get_voltage() and _regulator_do_set_voltage() both of which
will fail on a switch regulator when there is no supply (yet).
This causes registering of all axp22x regulators to fail with the
following errors:
[ 1.395249] vcc-lcd: failed to get the current voltage(-22)
[ 1.405131] axp20x-regulator axp20x-regulator: Failed to register dc1sw
[ 1.412436] axp20x-regulator: probe of axp20x-regulator failed with error -22
This commit removes the constrains on dc1sw / vcc-lcd fixing this problem.
Note that dcdc1 itself is contrained to the exact same values, so this
does not change anything.
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b223d6242c upstream.
This is the same issue fixed in commit dcf5341f01 ("ARM: dts:
sun8i-q8-common: Do not set constraints on dc1sw regulator").
Commit message copied:
dc1sw is an on/off only regulator and as such it cannot have constraints.
This is a limitation of the kernel regulator implementation which resolves
supplies on the first regulator_get(), which is done after applying
constraints, and applying the constrains will fail because it calls
_regulator_get_voltage() and _regulator_do_set_voltage() both of which
will fail on a switch regulator when there is no supply (yet).
This causes registering of all axp22x regulators to fail with the
following errors:
[ 1.395249] vcc-lcd: failed to get the current voltage(-22)
[ 1.405131] axp20x-regulator axp20x-regulator: Failed to register dc1sw
[ 1.412436] axp20x-regulator: probe of axp20x-regulator failed with error -22
This commit removes the constrains on dc1sw / vcc-lcd fixing this problem.
Note that dcdc1 itself is contrained to the exact same values, so this
does not change anything.
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 56530f5d2d upstream.
Currently pmd_mknotpresent will use a zero entry to respresent an
invalidated pmd.
Unfortunately this definition clashes with pmd_none, thus it is
possible for a race condition to occur if zap_pmd_range sees pmd_none
whilst __split_huge_pmd_locked is running too with pmdp_invalidate
just called.
This patch fixes the race condition by modifying pmd_mknotpresent to
create non-zero faulting entries (as is done in other architectures),
removing the ambiguity with pmd_none.
[catalin.marinas@arm.com: using L_PMD_SECT_VALID instead of PMD_TYPE_SECT]
Fixes: 8d96250700 ("ARM: mm: Transparent huge page support for LPAE systems.")
Reported-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Steve Capper <steve.capper@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6245318869 upstream.
In a subsequent patch, pmd_mknotpresent will clear the valid bit of the
pmd entry, resulting in a not-present entry from the hardware's
perspective. Unfortunately, pmd_present simply checks for a non-zero pmd
value and will therefore continue to return true even after a
pmd_mknotpresent operation. Since pmd_mknotpresent is only used for
managing huge entries, this is only an issue for the 3-level case.
This patch fixes the 3-level pmd_present implementation to take into
account the valid bit. For bisectability, the change is made before the
fix to pmd_mknotpresent.
[catalin.marinas@arm.com: comment update regarding pmd_mknotpresent patch]
Fixes: 8d96250700 ("ARM: mm: Transparent huge page support for LPAE systems.")
Cc: Russell King <linux@armlinux.org.uk>
Cc: Steve Capper <Steve.Capper@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d1e44b6b28 upstream.
After "regulator: qcom_smd: add list_voltage callback" patch adding
pm8941 lnldo regulators would bug on list_voltages as it is a fixed
regulator without any linear range.
This patch fixes that issue by adding dedicated ops for pm8941 lnldo
without list_voltages callback.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8a47540eb upstream.
This patch adds support to list_voltage callback, so that consumers
like mmc core, can get information of supported voltage range.
Without this patch there is no way for mmc core to know this voltage range.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 39a9beab5a upstream.
The spec allows backchannels for multiple clients to share the same tcp
connection. When that happens, we need to use the same xprt for all of
them. Similarly, we need the same xps.
This fixes list corruption introduced by the multipath code.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Acked-by: Trond Myklebust <trondmy@primarydata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e547f26283 upstream.
Olga Kornievskaia reports that the following test fails to trigger
an OPEN_DOWNGRADE on the wire, and only triggers the final CLOSE.
fd0 = open(foo, RDRW) -- should be open on the wire for "both"
fd1 = open(foo, RDONLY) -- should be open on the wire for "read"
close(fd0) -- should trigger an open_downgrade
read(fd1)
close(fd1)
The issue is that we're missing a check for whether or not the current
state transitioned from an O_RDWR state as opposed to having transitioned
from a combination of O_RDONLY and O_WRONLY.
Reported-by: Olga Kornievskaia <aglo@umich.edu>
Fixes: cd9288ffae ("NFSv4: Fix another bug in the close/open_downgrade code")
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d20cb71dbf upstream.
In "NFSv4: Move dentry instantiation into the NFSv4-specific atomic open code"
unconditional d_drop() after the ->open_context() had been removed. It had
been correct for success cases (there ->open_context() itself had been doing
dcache manipulations), but not for error ones. Only one of those (ENOENT)
got a compensatory d_drop() added in that commit, but in fact it should've
been done for all errors. As it is, the case of O_CREAT non-exclusive open
on a hashed negative dentry racing with e.g. symlink creation from another
client ended up with ->open_context() getting an error and proceeding to
call nfs_lookup(). On a hashed dentry, which would've instantly triggered
BUG_ON() in d_materialise_unique() (or, these days, its equivalent in
d_splice_alias()).
Tested-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e3a98883e upstream.
pnfs_generic_commit_cancel_empty_pagelist calls nfs_commitdata_release,
but that is wrong: nfs_commitdata_release puts the open context, something
that isn't valid until nfs_init_commit is called, which is never the case
when pnfs_generic_commit_cancel_empty_pagelist is called.
This was introduced in "nfs: avoid race that crashes nfs_init_commit".
Signed-off-by: Weston Andros Adamson <dros@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 999653786d upstream.
Use set_posix_acl, which includes proper permission checks, instead of
calling ->set_acl directly. Without this anyone may be able to grant
themselves permissions to a file by setting the ACL.
Lock the inode to make the new checks atomic with respect to set_acl.
(Also, nfsd was the only caller of set_acl not locking the inode, so I
suspect this may fix other races.)
This also simplifies the code, and ensures our ACLs are checked by
posix_acl_valid.
The permission checks and the inode locking were lost with commit
4ac7249e, which changed nfsd to use the set_acl inode operation directly
instead of going through xattr handlers.
Reported-by: David Sinquin <david@sinquin.eu>
[agreunba@redhat.com: use set_posix_acl]
Fixes: 4ac7249e
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5cc1fb2a09 upstream.
To avoid racing entry into nfs4_get_vfs_file().
Make init_open_stateid() return with locked stateid to be unlocked
by the caller.
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit feb9dad520 upstream.
It used to be the case that state had an rwlock that was locked for write
by downgrades, but for read for upgrades (opens). Well, the problem is
if there are two competing opens for the same state, they step on
each other toes potentially leading to leaking file descriptors
from the state structure, since access mode is a bitmap only set once.
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b7e9cde49 upstream.
For historic reasons, io_opt is in bytes and max_sectors in block layer
sectors. This interface inconsistency is error prone and should be
fixed. But for 4.4--4.7 let's make the unit difference explicit via a
wrapper function.
Fixes: d0eb20a863 ("sd: Optimal I/O size is in bytes, not sectors")
Reported-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: Andrew Patterson <andrew.patterson@hpe.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 62a584fe05 upstream.
As vm.dirty_[background_]bytes can't be applied verbatim to multiple
cgroup writeback domains, they get converted to percentages in
domain_dirty_limits() and applied the same way as
vm.dirty_[background]ratio. However, if the specified bytes is lower
than 1% of available memory, the calculated ratios become zero and the
writeback domain gets throttled constantly.
Fix it by using per-PAGE_SIZE instead of percentage for ratio
calculations. Also, the updated DIV_ROUND_UP() usages now should
yield 1/4096 (0.0244%) as the minimum ratio as long as the specified
bytes are above zero.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Miao Xie <miaoxie@huawei.com>
Link: http://lkml.kernel.org/g/57333E75.3080309@huawei.com
Fixes: 9fc3a43e17 ("writeback: separate out domain_dirty_limits()")
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adjusted comment based on Jan's suggestion.
Signed-off-by: Jens Axboe <axboe@fb.com>
commit f840ab18bd upstream.
The freq_table array is not populated before calling
thermal_of_cooling_register. The code which populates the freq table was
introduced in commit f6859014.
This should be done before registering new thermal cooling device.
The log shows effects of this wrong decision.
[ 2.172614] cpu cpu1: Failed to get voltage for frequency 1984518656000: -34
[ 2.220863] cpu cpu0: Failed to get voltage for frequency 1984524416000: -34
Fixes: f6859014c7 ("thermal: cpu_cooling: Store frequencies in descending order")
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Acked-by: Javi Merino <javi.merino@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a44323e2a8 upstream.
The current code goes through a lot of indirection just to call a
known handler. Simplify it: just call the handlers directly.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit de26859dcf upstream.
Commit 49f86ec21c ("rtlwifi: Change long delays to sleeps") was correct
for most cases; however, driver rtl8192ce calls the affected routines while
in atomic context. The kernel bug output is as follows:
BUG: scheduling while atomic: wpa_supplicant/627/0x00000002
[...]
[<ffffffff815c2b39>] __schedule+0x899/0xad0
[<ffffffff815c2dac>] schedule+0x3c/0x90
[<ffffffff815c5bb2>] schedule_hrtimeout_range_clock+0xa2/0x120
[<ffffffff810e8b80>] ? hrtimer_init+0x120/0x120
[<ffffffff815c5ba6>] ? schedule_hrtimeout_range_clock+0x96/0x120
[<ffffffff815c5c43>] schedule_hrtimeout_range+0x13/0x20
[<ffffffff815c568f>] usleep_range+0x4f/0x70
[<ffffffffa0667218>] rtl_rfreg_delay+0x38/0x50 [rtlwifi]
[<ffffffffa06dd0e7>] rtl92c_phy_config_rf_with_headerfile+0xc7/0xe0 [rtl8192ce]
To fix this bug, three of the changes from delay to sleep are reverted.
Unfortunately, one of the changes involves a delay of 50 msec. The calling
code will be modified so that this long delay can be avoided; however,
this change is being pushed now to fix the problem in kernel 4.6.0.
Fixes: 49f86ec21c ("rtlwifi: Change long delays to sleeps")
Reported-by: James Feeney <james@nurealm.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: James Feeney <james@nurealm.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e6ec03a25f upstream.
It's an analogue of commit 7500c38a (fix the braino in "namei:
massage lookup_slow() to be usable by lookup_one_len_unlocked()").
The same problem (->lookup()-returned unhashed negative dentry
just might be an autofs one with ->d_manage() that would wait
until the daemon makes it positive) applies in do_last() - we
need to do follow_managed() first.
Fortunately, remaining callers of follow_managed() are OK - only
autofs has that weirdness (negative dentry that does not mean
an instant -ENOENT)) and autofs never has its negative dentries
hashed, so we can't pick one from a dcache lookup.
->d_manage() is a bloody mess ;-/
Spotted-by: Ian Kent <raven@themaw.net>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 85b03b3033 upstream.
This reverts commit 923b93e451.
Make sure consumers do not overwrite gpio flags for pins that have
already been claimed.
While adding support for gpio drivers to refuse a request using
unsupported flags, the order of when the requested flag was checked and
the new flags were applied was reversed to that consumers could
overwrite flags for already requested gpios.
This not only affects device-tree setups where two drivers could request
the same gpio using conflicting configurations, but also allowed user
space to clear gpio flags for already claimed pins simply by attempting
to export them through the sysfs interface. By for example clearing the
FLAG_ACTIVE_LOW flag this way, user space could effectively change the
polarity of a signal.
Reverting this change obviously prevents gpio drivers from doing sanity
checks on the flags in their request callbacks. Fortunately only one
recently added driver (gpio-tps65218 in v4.6) appears to do this, and a
follow up patch could restore this functionality through a different
interface.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 87041a58d3 upstream.
This fixes the issue descirbe in bug 117531
(https://bugzilla.kernel.org/show_bug.cgi?id=117531).
It's a regression introduced in linux 4.5 that causes a Oops at load of
gpio_sch and prevents powering off the computer.
The issue is that sch_gpio_reg_set is called in sch_gpio_probe before
gpio_chip data is initialized with the pointer to the sch_gpio struct. As
sch_gpio_reg_set calls gpiochip_get_data, it returns NULL which causes
the Oops.
The patch follows Mika's advice (https://lkml.org/lkml/2016/5/9/61) and
consists in modifying sch_gpio_reg_get and sch_gpio_reg_set to take a
sch_gpio struct directly instead of a gpio_chip, which avoids the call to
gpiochip_get_data.
Thanks Mika for your patience with me :-)
Signed-off-by: Colin Pitrat <colin.pitrat@gmail.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c0a1ecb9f4 upstream.
Most functions that take a GPIO descriptor in need to check the
descriptor for IS_ERR(). We do this mostly in the VALIDATE_DESC()
macro except for the gpiod_to_irq() function which needs special
handling.
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 62e6d1e59c upstream.
If USB cable is connected prior to boot, we don't get any interrupts
so we must manually check the VBUS state and report it during probe.
If we don't do it then USB controller will never know that peripheral
cable was connected till the user unplugs and replugs the cable.
Fixes: b7aad8e268 ("extcon: palmas: Add the support for VBUS detection by using GPIO")
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ead852dd8 upstream.
Fix boot crash that triggers if this driver is built into a kernel and
run on non-AMD systems.
AMD northbridges users call amd_cache_northbridges() and it returns
a negative value to signal that we weren't able to cache/detect any
northbridges on the system.
At least, it should do so as all its callers expect it to do so. But it
does return a negative value only when kmalloc() fails.
Fix it to return -ENODEV if there are no NBs cached as otherwise, amd_nb
users like amd64_edac, for example, which relies on it to know whether
it should load or not, gets loaded on systems like Intel Xeons where it
shouldn't.
Reported-and-tested-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1466097230-5333-2-git-send-email-bp@alien8.de
Link: https://lkml.kernel.org/r/5761BEB0.9000807@cybernetics.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dcfc47248d upstream.
Fix kprobe_fault_handler() to clear the TF (trap flag) bit of
the flags register in the case of a fault fixup on single-stepping.
If we put a kprobe on the instruction which caused a
page fault (e.g. actual mov instructions in copy_user_*),
that fault happens on the single-stepping buffer. In this
case, kprobes resets running instance so that the CPU can
retry execution on the original ip address.
However, current code forgets to reset the TF bit. Since this
fault happens with TF bit set for enabling single-stepping,
when it retries, it causes a debug exception and kprobes
can not handle it because it already reset itself.
On the most of x86-64 platform, it can be easily reproduced
by using kprobe tracer. E.g.
# cd /sys/kernel/debug/tracing
# echo p copy_user_enhanced_fast_string+5 > kprobe_events
# echo 1 > events/kprobes/enable
And you'll see a kernel panic on do_debug(), since the debug
trap is not handled by kprobes.
To fix this problem, we just need to clear the TF bit when
resetting running kprobe.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Reviewed-by: Ananth N Mavinakayanahalli <ananth@linux.vnet.ibm.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: systemtap@sourceware.org
Link: http://lkml.kernel.org/r/20160611140648.25885.37482.stgit@devbox
[ Updated the comments. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9c77679cad upstream.
For newer versions of Syslinux, we need ldlinux.c32 in addition to
isolinux.bin to reside on the boot disk, so if the latter is found,
copy it, too, to the isoimage tree.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9bd616e3db upstream.
The cpuidle_devices per-CPU variable is only defined when CPU_IDLE is
enabled. Commit c8cc7d4de7 ("sched/idle: Reorganize the idle loop")
removed the #ifdef CONFIG_CPU_IDLE around cpuidle_idle_call() with the
compiler optimising away __this_cpu_read(cpuidle_devices). However, with
CONFIG_UBSAN && !CONFIG_CPU_IDLE, this optimisation no longer happens
and the kernel fails to link since cpuidle_devices is not defined.
This patch introduces an accessor function for the current CPU cpuidle
device (returning NULL when !CONFIG_CPU_IDLE) and uses it in
cpuidle_idle_call().
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c5ea0a9cd upstream.
The following scenario is possible:
CPU 1 CPU 2
static_key_slow_inc()
atomic_inc_not_zero()
-> key.enabled == 0, no increment
jump_label_lock()
atomic_inc_return()
-> key.enabled == 1 now
static_key_slow_inc()
atomic_inc_not_zero()
-> key.enabled == 1, inc to 2
return
** static key is wrong!
jump_label_update()
jump_label_unlock()
Testing the static key at the point marked by (**) will follow the
wrong path for jumps that have not been patched yet. This can
actually happen when creating many KVM virtual machines with userspace
LAPIC emulation; just run several copies of the following program:
#include <fcntl.h>
#include <unistd.h>
#include <sys/ioctl.h>
#include <linux/kvm.h>
int main(void)
{
for (;;) {
int kvmfd = open("/dev/kvm", O_RDONLY);
int vmfd = ioctl(kvmfd, KVM_CREATE_VM, 0);
close(ioctl(vmfd, KVM_CREATE_VCPU, 1));
close(vmfd);
close(kvmfd);
}
return 0;
}
Every KVM_CREATE_VCPU ioctl will attempt a static_key_slow_inc() call.
The static key's purpose is to skip NULL pointer checks and indeed one
of the processes eventually dereferences NULL.
As explained in the commit that introduced the bug:
706249c222 ("locking/static_keys: Rework update logic")
jump_label_update() needs key.enabled to be true. The solution adopted
here is to temporarily make key.enabled == -1, and use go down the
slow path when key.enabled <= 0.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 706249c222 ("locking/static_keys: Rework update logic")
Link: http://lkml.kernel.org/r/1466527937-69798-1-git-send-email-pbonzini@redhat.com
[ Small stylistic edits to the changelog and the code. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c61002271 upstream.
While this prior commit:
54cf809b95 ("locking,qspinlock: Fix spin_is_locked() and spin_unlock_wait()")
... fixes spin_is_locked() and spin_unlock_wait() for the usage
in ipc/sem and netfilter, it does not in fact work right for the
usage in task_work and futex.
So while the 2 locks crossed problem:
spin_lock(A) spin_lock(B)
if (!spin_is_locked(B)) spin_unlock_wait(A)
foo() foo();
... works with the smp_mb() injected by both spin_is_locked() and
spin_unlock_wait(), this is not sufficient for:
flag = 1;
smp_mb(); spin_lock()
spin_unlock_wait() if (!flag)
// add to lockless list
// iterate lockless list
... because in this scenario, the store from spin_lock() can be delayed
past the load of flag, uncrossing the variables and loosing the
guarantee.
This patch reworks spin_is_locked() and spin_unlock_wait() to work in
both cases by exploiting the observation that while the lock byte
store can be delayed, the contender must have registered itself
visibly in other state contained in the word.
It also allows for architectures to override both functions, as PPC
and ARM64 have an additional issue for which we currently have no
generic solution.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Giovanni Gherdovich <ggherdovich@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Pan Xinhui <xinhui.pan@linux.vnet.ibm.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <waiman.long@hpe.com>
Cc: Will Deacon <will.deacon@arm.com>
Fixes: 54cf809b95 ("locking,qspinlock: Fix spin_is_locked() and spin_unlock_wait()")
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3993546646 upstream.
The kernel-doc for the of_irq_get[_byname]() is clearly inadequate in
describing the return values -- of_irq_get_byname() is documented better
than of_irq_get() but it still doesn't mention that 0 is returned iff
irq_create_of_mapping() fails (it doesn't return an error code in this
case). Document all possible return value variants, making the writing
of the word "IRQ" consistent, while at it...
Fixes: 9ec36cafe4 ("of/irq: do irq resolution in platform_get_irq")
Fixes: ad69674e73 ("of/irq: do irq resolution in platform_get_irq_byname()")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b3c0a4dab7 upstream.
Because of an improper dereference, a stray 'C' character was output to
the modalias when no 'compatible' was specified. This is the case for
some old PowerMac drivers which only set the 'name' property. Fix it to
let them match again.
Reported-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Mathieu Malaterre <malat@debian.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Fixes: 6543becf26 ("mod/file2alias: make modalias generation safe for cross compiling")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 97c1df3e54 upstream.
Add this trivial missing error handling.
Fixes: 1b852bceb0 ("mnt: Refactor the logic for mounting sysfs and proc in a user namespace")
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 695e9df010 upstream.
In rare cases it is possible for s_flags & MS_RDONLY to be set but
MNT_READONLY to be clear. This starting combination can cause
fs_fully_visible to fail to ensure that the new mount is readonly.
Therefore force MNT_LOCK_READONLY in the new mount if MS_RDONLY
is set on the source filesystem of the mount.
In general both MS_RDONLY and MNT_READONLY are set at the same for
mounts so I don't expect any programs to care. Nor do I expect
MS_RDONLY to be set on proc or sysfs in the initial user namespace,
which further decreases the likelyhood of problems.
Which means this change should only affect system configurations by
paranoid sysadmins who should welcome the additional protection
as it keeps people from wriggling out of their policies.
Fixes: 8c6cf9cc82 ("mnt: Modify fs_fully_visible to deal with locked ro nodev and atime")
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d71ed6c930 upstream.
MNT_LOCKED implies on a child mount implies the child is locked to the
parent. So while looping through the children the children should be
tested (not their parent).
Typically an unshare of a mount namespace locks all mounts together
making both the parent and the slave as locked but there are a few
corner cases where other things work.
Fixes: ceeb0e5d39 ("vfs: Ignore unlocked mounts in fs_fully_visible")
Reported-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea1d39a31d upstream.
Fix warning about tainted kernel because usb-otg-fsm has no license.
WARNING: with this patch usb-otg-fsm module can be loaded
but then the kernel will hang. Tested with a udoo quad board.
Signed-off-by: Oscar <oscar@naiandei.net>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ab2a4bf839 upstream.
The USB core contains a bug that can show up when a USB-3 host
controller is removed. If the primary (USB-2) hcd structure is
released before the shared (USB-3) hcd, the core will try to do a
double-free of the common bandwidth_mutex.
The problem was described in graphical form by Chung-Geol Kim, who
first reported it:
=================================================
At *remove USB(3.0) Storage
sequence <1> --> <5> ((Problem Case))
=================================================
VOLD
------------------------------------|------------
(uevent)
________|_________
|<1> |
|dwc3_otg_sm_work |
|usb_put_hcd |
|peer_hcd(kref=2)|
|__________________|
________|_________
|<2> |
|New USB BUS #2 |
| |
|peer_hcd(kref=1) |
| |
--(Link)-bandXX_mutex|
| |__________________|
|
___________________ |
|<3> | |
|dwc3_otg_sm_work | |
|usb_put_hcd | |
|primary_hcd(kref=1)| |
|___________________| |
_________|_________ |
|<4> | |
|New USB BUS #1 | |
|hcd_release | |
|primary_hcd(kref=0)| |
| | |
|bandXX_mutex(free) |<-
|___________________|
(( VOLD ))
______|___________
|<5> |
| SCSI |
|usb_put_hcd |
|peer_hcd(kref=0) |
|*hcd_release |
|bandXX_mutex(free*)|<- double free
|__________________|
=================================================
This happens because hcd_release() frees the bandwidth_mutex whenever
it sees a primary hcd being released (which is not a very good idea
in any case), but in the course of releasing the primary hcd, it
changes the pointers in the shared hcd in such a way that the shared
hcd will appear to be primary when it gets released.
This patch fixes the problem by changing hcd_release() so that it
deallocates the bandwidth_mutex only when the _last_ hcd structure
referencing it is released. The patch also removes an unnecessary
test, so that when an hcd is released, both the shared_hcd and
primary_hcd pointers in the hcd's peer will be cleared.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Chung-Geol Kim <chunggeol.kim@samsung.com>
Tested-by: Chung-Geol Kim <chunggeol.kim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e8b3dfef1 upstream.
The HOSTPC extension registers found in some EHCI implementations form
a variable-length array, with one element for each port. Therefore
the hostpc field in struct ehci_regs should be declared as a
zero-length array, not a single-element array.
This fixes a problem reported by UBSAN.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Wilfried Klaebe <linux-kernel@lebenslange-mailadresse.de>
Tested-by: Wilfried Klaebe <linux-kernel@lebenslange-mailadresse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23e3439296 upstream.
A patch that went into Linux-4.4 to fix big-endian mode on a Lantiq
MIPS system unfortunately broke big-endian operation on PowerPC
APM82181 as reported by Christian Lamparter, and likely other
systems.
It actually introduced multiple issues:
- it broke big-endian ARM kernels: any machine that was working
correctly with a little-endian kernel is no longer using byteswaps
on big-endian kernels, which clearly breaks them.
- On PowerPC the same thing must be true: if it was working before,
using big-endian kernels is now broken. Unlike ARM, 32-bit PowerPC
usually uses big-endian kernels, so they are likely all broken.
- The barrier for dwc2_writel is on the wrong side of the __raw_writel(),
so the MMIO no longer synchronizes with DMA operations.
- On architectures that require specific CPU instructions for MMIO
access, using the __raw_ variant may turn this into a pointer
dereference that does not have the same effect as the readl/writel.
This patch is a simple revert for all architectures other than MIPS,
in the hope that we can more easily backport it to fix the regression
on PowerPC and ARM systems without breaking the Lantiq system again.
We should follow this up with a more elaborate change to add runtime
detection of endianness, to make sure it also works on all other
combinations of architectures and implementations of the usb-dwc2
device. That patch however will be fairly large and not appropriate
for backports to stable kernels.
Felipe suggested a different approach, using an endianness switching
register to always put the device into LE mode, but unfortunately
the dwc2 hardware does not provide a generic way to do that. Also,
I see no practical way of addressing the problem more generally by
patching architecture specific code on MIPS.
Fixes: 95c8bc3609 ("usb: dwc2: Use platform endianness when accessing registers")
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e96a87c54 upstream.
Userspace can quite legitimately perform an exec() syscall with a
suspended transaction. exec() does not return to the old process, rather
it load a new one and starts that, the expectation therefore is that the
new process starts not in a transaction. Currently exec() is not treated
any differently to any other syscall which creates problems.
Firstly it could allow a new process to start with a suspended
transaction for a binary that no longer exists. This means that the
checkpointed state won't be valid and if the suspended transaction were
ever to be resumed and subsequently aborted (a possibility which is
exceedingly likely as exec()ing will likely doom the transaction) the
new process will jump to invalid state.
Secondly the incorrect attempt to keep the transactional state while
still zeroing state for the new process creates at least two TM Bad
Things. The first triggers on the rfid to return to userspace as
start_thread() has given the new process a 'clean' MSR but the suspend
will still be set in the hardware MSR. The second TM Bad Thing triggers
in __switch_to() as the processor is still transactionally suspended but
__switch_to() wants to zero the TM sprs for the new process.
This is an example of the outcome of calling exec() with a suspended
transaction. Note the first 700 is likely the first TM bad thing
decsribed earlier only the kernel can't report it as we've loaded
userspace registers. c000000000009980 is the rfid in
fast_exception_return()
Bad kernel stack pointer 3fffcfa1a370 at c000000000009980
Oops: Bad kernel stack pointer, sig: 6 [#1]
CPU: 0 PID: 2006 Comm: tm-execed Not tainted
NIP: c000000000009980 LR: 0000000000000000 CTR: 0000000000000000
REGS: c00000003ffefd40 TRAP: 0700 Not tainted
MSR: 8000000300201031 <SF,ME,IR,DR,LE,TM[SE]> CR: 00000000 XER: 00000000
CFAR: c0000000000098b4 SOFTE: 0
PACATMSCRATCH: b00000010000d033
GPR00: 0000000000000000 00003fffcfa1a370 0000000000000000 0000000000000000
GPR04: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR08: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR12: 00003fff966611c0 0000000000000000 0000000000000000 0000000000000000
NIP [c000000000009980] fast_exception_return+0xb0/0xb8
LR [0000000000000000] (null)
Call Trace:
Instruction dump:
f84d0278 e9a100d8 7c7b03a6 e84101a0 7c4ff120 e8410170 7c5a03a6 e8010070
e8410080 e8610088 e8810090 e8210078 <4c000024> 48000000 e8610178 88ed023b
Kernel BUG at c000000000043e80 [verbose debug info unavailable]
Unexpected TM Bad Thing exception at c000000000043e80 (msr 0x201033)
Oops: Unrecoverable exception, sig: 6 [#2]
CPU: 0 PID: 2006 Comm: tm-execed Tainted: G D
task: c0000000fbea6d80 ti: c00000003ffec000 task.ti: c0000000fb7ec000
NIP: c000000000043e80 LR: c000000000015a24 CTR: 0000000000000000
REGS: c00000003ffef7e0 TRAP: 0700 Tainted: G D
MSR: 8000000300201033 <SF,ME,IR,DR,RI,LE,TM[SE]> CR: 28002828 XER: 00000000
CFAR: c000000000015a20 SOFTE: 0
PACATMSCRATCH: b00000010000d033
GPR00: 0000000000000000 c00000003ffefa60 c000000000db5500 c0000000fbead000
GPR04: 8000000300001033 2222222222222222 2222222222222222 00000000ff160000
GPR08: 0000000000000000 800000010000d033 c0000000fb7e3ea0 c00000000fe00004
GPR12: 0000000000002200 c00000000fe00000 0000000000000000 0000000000000000
GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR20: 0000000000000000 0000000000000000 c0000000fbea7410 00000000ff160000
GPR24: c0000000ffe1f600 c0000000fbea8700 c0000000fbea8700 c0000000fbead000
GPR28: c000000000e20198 c0000000fbea6d80 c0000000fbeab680 c0000000fbea6d80
NIP [c000000000043e80] tm_restore_sprs+0xc/0x1c
LR [c000000000015a24] __switch_to+0x1f4/0x420
Call Trace:
Instruction dump:
7c800164 4e800020 7c0022a6 f80304a8 7c0222a6 f80304b0 7c0122a6 f80304b8
4e800020 e80304a8 7c0023a6 e80304b0 <7c0223a6> e80304b8 7c0123a6 4e800020
This fixes CVE-2016-5828.
Fixes: bc2a9408fa ("powerpc: Hook in new transactional memory code")
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c2a63e301 upstream.
The recent commit 7cc851039d ("powerpc/pseries: Add POWER8NVL support
to ibm,client-architecture-support call") added a new PVR mask & value
to the start of the ibm_architecture_vec[] array.
However it missed the fact that further down in the array, we hard code
the offset of one of the fields, and then at boot use that value to
patch the value in the array. This means every update to the array must
also update the #define, ugh.
This means that on pseries machines we will misreport to firmware the
number of cores we support, by a factor of threads_per_core.
Fix it for now by updating the #define.
Fixes: 7cc851039d ("powerpc/pseries: Add POWER8NVL support to ibm,client-architecture-support call")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a934efe94 upstream.
In commit 8445a87f70 "powerpc/iommu: Remove the dependency on EEH
struct in DDW mechanism", the PE address was replaced with the PCI
config address in order to remove dependency on EEH. According to PAPR
spec, firmware (pHyp or QEMU) should accept "xxBBSSxx" format PCI config
address, not "xxxxBBSS" provided by the patch. Note that "BB" is PCI bus
number and "SS" is the combination of slot and function number.
This fixes the PCI address passed to DDW RTAS calls.
Fixes: 8445a87f70 ("powerpc/iommu: Remove the dependency on EEH struct in DDW mechanism")
Reported-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Tested-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8445a87f70 upstream.
Commit 39baadbf36 ("powerpc/eeh: Remove eeh information from pci_dn")
changed the pci_dn struct by removing its EEH-related members.
As part of this clean-up, DDW mechanism was modified to read the device
configuration address from eeh_dev struct.
As a consequence, now if we disable EEH mechanism on kernel command-line
for example, the DDW mechanism will fail, generating a kernel oops by
dereferencing a NULL pointer (which turns to be the eeh_dev pointer).
This patch just changes the configuration address calculation on DDW
functions to a manual calculation based on pci_dn members instead of
using eeh_dev-based address.
No functional changes were made. This was tested on pSeries, both
in PHyp and qemu guest.
Fixes: 39baadbf36 ("powerpc/eeh: Remove eeh information from pci_dn")
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c5122e45a upstream.
When this code was reworked for IBoE support the order of assignments
for the sl_tclass_flowlabel got flipped around resulting in
TClass & FlowLabel being permanently set to 0 in the packet headers.
This breaks IB routers that rely on these headers, but only affects
kernel users - libmlx4 does this properly for user space.
Fixes: fa417f7b52 ("IB/mlx4: Add support for IBoE")
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 47355b3cd7 upstream.
ib_device_cap_flags 64-bit expansion caused caps overlapping
and made consumers read wrong device capabilities. For example
IB_DEVICE_SG_GAPS_REG was falsely read by the iser driver causing
it to use a non-existing capability. This happened because signed
int becomes sign extended when converted it to u64. Fix this by
casting IB_DEVICE_ON_DEMAND_PAGING enumeration to ULL.
Fixes: f5aa9159a4 ('IB/core: Add arbitrary sg_list support')
Reported-by: Robert LeBlanc <robert@leblancnet.us>
Acked-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 077fa7aed1 upstream.
Mike Galbraith reported that the LTP test case futex_wake04 was broken
by commit 65d8fc777f ("futex: Remove requirement for lock_page()
in get_futex_key()").
This test case uses futexes backed by hugetlbfs pages and so there is an
associated inode with a futex stored on such pages. The problem is that
the key is being calculated based on the head page index of the hugetlbfs
page and not the tail page.
Prior to the optimisation, the page lock was used to stabilise mappings and
pin the inode is file-backed which is overkill. If the page was a compound
page, the head page was automatically looked up as part of the page lock
operation but the tail page index was used to calculate the futex key.
After the optimisation, the compound head is looked up early and the page
lock is only relied upon to identify truncated pages, special pages or a
shmem page moving to swapcache. The head page is looked up because without
the page lock, special care has to be taken to pin the inode correctly.
However, the tail page is still required to calculate the futex key so
this patch records the tail page.
On vanilla 4.6, the output of the test case is;
futex_wake04 0 TINFO : Hugepagesize 2097152
futex_wake04 1 TFAIL : futex_wake04.c:126: Bug: wait_thread2 did not wake after 30 secs.
With the patch applied
futex_wake04 0 TINFO : Hugepagesize 2097152
futex_wake04 1 TPASS : Hi hydra, thread2 awake!
Fixes: 65d8fc777f "futex: Remove requirement for lock_page() in get_futex_key()"
Reported-and-tested-by: Mike Galbraith <umgwanakikbuti@gmail.com>
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Davidlohr Bueso <dave@stgolabs.net>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/20160608132522.GM2469@suse.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c041778c96 upstream.
The PDU length of incoming LLC frames is set to the total skb payload size
in __ieee80211_data_to_8023() of net/wireless/util.c which incorrectly
includes the length of the IEEE 802.11 header.
The resulting LLC frame header has a too large PDU length, causing the
llc_fixup_skb() function of net/llc/llc_input.c to reject the incoming
skb, effectively breaking STP.
Solve the problem by properly substracting the IEEE 802.11 frame header size
from the PDU length, allowing the LLC processor to pick up the incoming
control messages.
Special thanks to Gerry Rozema for tracking down the regression and proposing
a suitable patch.
Fixes: 2d1c304cb2 ("cfg80211: add function for 802.3 conversion with separate output buffer")
Reported-by: Gerry Rozema <gerryr@rozeware.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 126e755732 upstream.
If a user space program (e.g., wpa_supplicant) deletes a STA entry that
is currently in NL80211_PLINK_ESTAB state, the number of established
plinks counter was not decremented and this could result in rejecting
new plink establishment before really hitting the real maximum plink
limit. For !user_mpm case, this decrementation is handled by
mesh_plink_deactive().
Fix this by decrementing estab_plinks on STA deletion
(mesh_sta_cleanup() gets called from there) so that the counter has a
correct value and the Beacon frame advertisement in Mesh Configuration
element shows the proper value for capability to accept additional
peers.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 62397da50b upstream.
A wmediumd that does not send this attribute causes a NULL pointer
dereference, as the attribute is accessed even if it does not exist.
The attribute was required but never checked ever since userspace frame
forwarding has been introduced. The issue gets more problematic once we
allow wmediumd registration from user namespaces.
Fixes: 7882513bac ("mac80211_hwsim driver support userspace frame tx/rx")
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6fe04128f1 upstream.
The header field is defined as u8[] but also accessed as struct
ieee80211_hdr. Enforce an alignment of 2 to prevent unnecessary
unaligned accesses, which can be very harmful for performance on many
platforms.
Fixes: e495c24731 ("mac80211: extend fast-xmit for more ciphers")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6cbf6236d5 upstream.
Since set_tx_power and set_antenna are frequently implemented
without the matching get_tx_power/get_antenna, we shouldn't
have added warnings for those. Remove them.
The remaining ones are correct and need to be implemented
symmetrically for correct operation.
Fixes: de3bb771f4 ("cfg80211: add more warnings for inconsistent ops")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4879efb34f upstream.
dwc3-exynos has two problems during init if the regulators are slow
to come up (for instance if the I2C bus driver is not on the initramfs)
and return probe deferral. First, every time this happens, the driver
leaks the USB phys created; they need to be deallocated on error.
Second, since the phy devices are created before the regulators fail,
this means that there's a new device to re-trigger deferred probing,
which causes it to essentially go into a busy loop of re-probing the
device until the regulators come up.
Move the phy creation to after the regulators have succeeded, and also
fix cleanup on failure. On my ODROID XU4 system (with Debian's initramfs
which doesn't contain the I2C driver), this reduces the number of probe
attempts (for each of the two controllers) from more than 2000 to eight.
Signed-off-by: Steinar H. Gunderson <sesse@google.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Vivek Gautam <gautam.vivek@samsung.com>
Fixes: d720f057fd ("usb: dwc3: exynos: add nop transceiver support")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f8a15a9650 upstream.
There are three EHCI controllers on Tegra SoCs, each with its own reset
line. However, the first controller contains a set of UTMI configuration
registers that are shared with its siblings. These registers will only
be reset as part of the first controller's reset. For proper operation
it must be ensured that the UTMI configuration registers are reset
before any of the EHCI controllers are enabled, irrespective of the
probe order.
Commit a47cc24cd1 ("USB: EHCI: tegra: Fix probe order issue leading to
broken USB") introduced code that ensures the first controller is always
reset before setting up any of the controllers, and is never again reset
afterwards.
This code, however, grabs the wrong reset. Each EHCI controller has two
reset controls attached: 1) the USB controller reset and 2) the UTMI
pads reset (really the first controller's reset). In order to reset the
UTMI pads registers the code must grab the second reset, but instead it
grabbing the first.
Fixes: a47cc24cd1 ("USB: EHCI: tegra: Fix probe order issue leading to broken USB")
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dcb21ad438 upstream.
parport subsystem has introduced parport_del_port() to delete a port
when it is going away. Without parport_del_port() the registered port
will not be unregistered.
To reproduce and verify the error:
Command to be used is : ls /sys/bus/parport/devices
1) without the device attached there is no output as there is no
registered parport.
2) Attach the device, and the command will show "parport0".
3) Remove the device and the command still shows "parport0".
4) Attach the device again and we get "parport1".
With the patch applied:
1) without the device attached there is no output as there is no
registered parport.
2) Attach the device, and the command will show "parport0".
3) Remove the device and there is no output as "parport0" is now
removed.
4) Attach device again to get "parport0" again.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3425aa03f4 upstream.
If commands timeout we mark them for abortion, then stop the command
ring, and turn the commands to no-ops and finally restart the command
ring.
If the host is working properly the no-op commands will finish and
pending completions are called.
If we notice the host is failing, driver clears the command ring and
completes, deletes and frees all pending commands.
There are two separate cases reported where host is believed to work
properly but is not. In the first case we successfully stop the ring
but no abort or stop command ring event is ever sent and host locks up.
The second case is if a host is removed, command times out and driver
believes the ring is stopped, and assumes it will be restarted, but
actually ends up timing out on the same command forever.
If one of the pending commands has the xhci->mutex held it will block
xhci_stop() in the remove codepath which otherwise would cleanup pending
commands.
Add a check that clears all pending commands in case host is removed,
or we are stuck timing out on the same command. Also restart the
command timeout timer when stopping the command ring to ensure we
recive an ring stop/abort event.
Tested-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d95815ba6a upstream.
I got one of these cards for testing uas with, it seems that with streams
it dma-s all over the place, corrupting memory. On my first tests it
managed to dma over the BIOS of the motherboard somehow and completely
bricked it.
Tests on another motherboard show that it does work with streams disabled.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit de95c40d5b upstream.
On some platforms, the clocks might be registered by a platform
driver. When this is the case, the clock platform driver may very well
be probed after xhci-plat, in which case the first probe() invocation
of xhci-plat will receive -EPROBE_DEFER as the return value of
devm_clk_get().
The current code handles that as a normal error, and simply assumes
that this means that the system doesn't have a clock for the XHCI
controller, and continues probing without calling
clk_prepare_enable(). Unfortunately, this doesn't work on systems
where the XHCI controller does have a clock, but that clock is
provided by another platform driver. In order to fix this situation,
we handle the -EPROBE_DEFER error condition specially, and abort the
XHCI controller probe(). It will be retried later automatically, the
clock will be available, devm_clk_get() will succeed, and the probe()
will continue with the clock prepared and enabled as expected.
In practice, such issue is seen on the ARM64 Marvell 7K/8K platform,
where the clocks are registered by a platform driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 27a41a83ec upstream.
Under stress occasions some TI devices might not return early when
reading the status register during the quirk invocation of xhci_irq made
by usb_hcd_pci_remove. This means that instead of returning, we end up
handling this interruption in the middle of a shutdown. Since
xhci->event_ring has already been freed in xhci_mem_cleanup, we end up
accessing freed memory, causing the Oops below.
commit 8c24d6d7b0 ("usb: xhci: stop everything on the first call to
xhci_stop") is the one that changed the instant in which we clean up the
event queue when stopping a device. Before, we didn't call
xhci_mem_cleanup at the first time xhci_stop is executed (for the shared
HCD), instead, we only did it after the invocation for the primary HCD,
much later at the removal path. The code flow for this oops looks like
this:
xhci_pci_remove()
usb_remove_hcd(xhci->shared)
xhci_stop(xhci->shared)
xhci_halt()
xhci_mem_cleanup(xhci); // Free the event_queue
usb_hcd_pci_remove(primary)
xhci_irq() // Access the event_queue if STS_EINT is set. Crash.
xhci_stop()
xhci_halt()
// return early
The fix modifies xhci_stop to only cleanup the xhci data when releasing
the primary HCD. This way, we still have the event_queue configured
when invoking xhci_irq. We still halt the device on the first call to
xhci_stop, though.
I could reproduce this issue several times on the mainline kernel by
doing a bind-unbind stress test with a specific storage gadget attached.
I also ran the same test over-night with my patch applied and didn't
observe the issue anymore.
[ 113.334124] Unable to handle kernel paging request for data at address 0x00000028
[ 113.335514] Faulting instruction address: 0xd00000000d4f767c
[ 113.336839] Oops: Kernel access of bad area, sig: 11 [#1]
[ 113.338214] SMP NR_CPUS=1024 NUMA PowerNV
[c000000efe47ba90] c000000000720850 usb_hcd_irq+0x50/0x80
[c000000efe47bac0] c00000000073d328 usb_hcd_pci_remove+0x68/0x1f0
[c000000efe47bb00] d00000000daf0128 xhci_pci_remove+0x78/0xb0
[xhci_pci]
[c000000efe47bb30] c00000000055cf70 pci_device_remove+0x70/0x110
[c000000efe47bb70] c00000000061c6bc __device_release_driver+0xbc/0x190
[c000000efe47bba0] c00000000061c7d0 device_release_driver+0x40/0x70
[c000000efe47bbd0] c000000000619510 unbind_store+0x120/0x150
[c000000efe47bc20] c0000000006183c4 drv_attr_store+0x64/0xa0
[c000000efe47bc60] c00000000039f1d0 sysfs_kf_write+0x80/0xb0
[c000000efe47bca0] c00000000039e14c kernfs_fop_write+0x18c/0x1f0
[c000000efe47bcf0] c0000000002e962c __vfs_write+0x6c/0x190
[c000000efe47bd90] c0000000002eab40 vfs_write+0xc0/0x200
[c000000efe47bde0] c0000000002ec85c SyS_write+0x6c/0x110
[c000000efe47be30] c000000000009260 system_call+0x38/0x108
Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Cc: Roger Quadros <rogerq@ti.com>
Cc: joel@jms.id.au
Reviewed-by: Roger Quadros <rogerq@ti.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 04471eb8c3 upstream.
Incorrect cppi dma channel is referenced in musb_rx_dma_iso_cppi41(),
which causes kernel NULL pointer reference oops later when calling
cppi41_dma_channel_program().
Fixes: 069a3fd (usb: musb: Remove ifdefs for musb_host_rx in musb_host.c
part1)
Reported-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f3eec0cf78 upstream.
shared_fifo endpoints would only get a previous tx state cleared
out, the rx state was only cleared for non shared_fifo endpoints
Change this so that the rx state is cleared for all endpoints.
This addresses an issue that resulted in rx packets being dropped
silently.
Signed-off-by: Andrew Goodbody <andrew.goodbody@cambrionix.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b2c17f829 upstream.
Ensure that the endpoint is stopped by clearing REQPKT before
clearing DATAERR_NAKTIMEOUT before rotating the queue on the
dedicated bulk endpoint.
This addresses an issue where a race could result in the endpoint
receiving data before it was reprogrammed resulting in a warning
about such data from musb_rx_reinit before it was thrown away.
The data thrown away was a valid packet that had been correctly
ACKed which meant the host and device got out of sync.
Signed-off-by: Andrew Goodbody <andrew.goodbody@cambrionix.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 84ac5d1140 upstream.
If the session bit was not set in the backup of devctl register,
restoring devctl would clear the session bit. Therefor, only restore
devctl register when the session bit was set in the backup.
This solves the device enumeration failure in otg mode exposed by commit
56f487c (PM / Runtime: Update last_busy in rpm_resume).
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 32cb0b3709 upstream.
The Acer C120 LED Projector is a USB-3 connected pico projector which
takes both its power and video data from USB-3.
In combination with some hubs this device does not play well with
lpm, so disable lpm for it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 593224ea77 upstream.
Commit 198de51dbc ("USB: uas: Limit qdepth at the scsi-host level")
removed the scsi_change_queue_depth() call from uas_slave_configure()
assuming that the slave would inherit the host's queue_depth, which
that commit sets to the same value.
This is incorrect, without the scsi_change_queue_depth() call the slave's
queue_depth defaults to 1, introducing a performance regression.
This commit restores the call, fixing the performance regression.
Fixes: 198de51dbc ("USB: uas: Limit qdepth at the scsi-host level")
Reported-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 055ddaace0 upstream.
Commit 9aa867e465 ("crypto: user - Add CRYPTO_MSG_DELRNG")
accidentally removed the minimum size check for CRYPTO_MSG_GETALG
netlink messages. This allows userland to send a truncated
CRYPTO_MSG_GETALG message as short as a netlink header only making
crypto_report() operate on uninitialized memory by accessing data
beyond the end of the netlink message.
Fix this be re-adding the minimum required size of CRYPTO_MSG_GETALG
messages to the crypto_msg_min[] array.
Fixes: 9aa867e465 ("crypto: user - Add CRYPTO_MSG_DELRNG")
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 12d3f49e1f upstream.
All of the VMX AES ciphers (AES, AES-CBC and AES-CTR) are set at
priority 1000. Unfortunately this means we never use AES-CBC and
AES-CTR, because the base AES-CBC cipher that is implemented on
top of AES inherits its priority.
To fix this, AES-CBC and AES-CTR have to be a higher priority. Set
them to 2000.
Testing on a POWER8 with:
cryptsetup benchmark --cipher aes --key-size 256
Shows decryption speed increase from 402.4 MB/s to 3069.2 MB/s,
over 7x faster. Thanks to Mike Strosaker for helping me debug
this issue.
Fixes: 8c755ace35 ("crypto: vmx - Adding CBC routines for VMX module")
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4a7d99ea1b ]
A socket connection made in ax.25 is not closed when session is
completed. The heartbeat timer is stopped prematurely and this is
where the socket gets closed. Allow heatbeat timer to run to close
socket. Symptom occurs in kernels >= 4.2.0
Originally sent 6/15/2016. Resend with distribution list matching
scripts/maintainer.pl output.
Signed-off-by: Basil Gunn <basil@pacabunga.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b560f03ddf ]
neigh_xmit() expects to be called inside an RCU-bh read side critical
section, and while one of its two current callers gets this right, the
other one doesn't.
More specifically, neigh_xmit() has two callers, mpls_forward() and
mpls_output(), and while both callers call neigh_xmit() under
rcu_read_lock(), this provides sufficient protection for neigh_xmit()
only in the case of mpls_forward(), as that is always called from
softirq context and therefore doesn't need explicit BH protection,
while mpls_output() can be called from process context with softirqs
enabled.
When mpls_output() is called from process context, with softirqs
enabled, we can be preempted by a softirq at any time, and RCU-bh
considers the completion of a softirq as signaling the end of any
pending read-side critical sections, so if we do get a softirq
while we are in the part of neigh_xmit() that expects to be run inside
an RCU-bh read side critical section, we can end up with an unexpected
RCU grace period running right in the middle of that critical section,
making things go boom.
This patch fixes this impedance mismatch in the callee, by making
neigh_xmit() always take rcu_read_{,un}lock_bh() around the code that
expects to be treated as an RCU-bh read side critical section, as this
seems a safer option than fixing it in the callers.
Fixes: 4fd3d7d9e8 ("neigh: Add helper function neigh_xmit")
Signed-off-by: David Barroso <dbarroso@fastly.com>
Signed-off-by: Lennert Buytenhek <lbuytenhek@fastly.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ceb5607035 ]
Commit dead9f29dd ("perf: Fix race in BPF program unregister") moved
destruction of BPF program from free_event_rcu() callback to __free_event(),
which is problematic if used with tail calls: if prog A is attached as
trace event directly, but at the same time present in a tail call map used
by another trace event program elsewhere, then we need to delay destruction
via RCU grace period since it can still be in use by the program doing the
tail call (the prog first needs to be dropped from the tail call map, then
trace event with prog A attached destroyed, so we get immediate destruction).
Fixes: dead9f29dd ("perf: Fix race in BPF program unregister")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Cc: Jann Horn <jann@thejh.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9a0fee2b55 ]
Diag intends to broadcast tcp_sk and udp_sk socket destruction.
Testing sk->sk_protocol for IPPROTO_TCP/IPPROTO_UDP alone is not
sufficient for this. Raw sockets can have the same type.
Add a test for sk->sk_type.
Fixes: eb4cb00852 ("sock_diag: define destruction multicast groups")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0888d5f3c0 ]
The bridge is falsly dropping ipv6 mulitcast packets if there is:
1. No ipv6 address assigned on the brigde.
2. No external mld querier present.
3. The internal querier enabled.
When the bridge fails to build mld queries, because it has no
ipv6 address, it slilently returns, but keeps the local querier enabled.
This specific case causes confusing packet loss.
Ipv6 multicast snooping can only work if:
a) An external querier is present
OR
b) The bridge has an ipv6 address an is capable of sending own queries
Otherwise it has to forward/flood the ipv6 multicast traffic,
because snooping cannot work.
This patch fixes the issue by adding a flag to the bridge struct that
indicates that there is currently no ipv6 address assinged to the bridge
and returns a false state for the local querier in
__br_multicast_querier_exists().
Special thanks to Linus Lüssing.
Fixes: d1d81d4c3d ("bridge: check return value of ipv6_dev_get_saddr()")
Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
Acked-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 70a0dec451 ]
This fixes wrong-interface signaling on 32-bit platforms for entries
created when jiffies > 2^31 + MFC_ASSERT_THRESH.
Signed-off-by: Tom Goff <thomas.goff@ll.mit.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 962fcef33b ]
Blair Steven noticed that ESN in conjunction with UDP encapsulation
is broken because we set the temporary ESP header to the wrong spot.
This patch fixes this by first of all using the right spot, i.e.,
4 bytes off the real ESP header, and then saving this information
so that after encryption we can restore it properly.
Fixes: 7021b2e1cd ("esp4: Switch to new AEAD interface")
Reported-by: Blair Steven <Blair.Steven@alliedtelesis.co.nz>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d5d8760b78 ]
Since 32b8a8e59c ("sit: add IPv4 over IPv4 support")
ipip6_err() may be called for packets whose IP protocol is
IPPROTO_IPIP as well as those whose IP protocol is IPPROTO_IPV6.
In the case of IPPROTO_IPIP packets the correct protocol value is not
passed to ipv4_update_pmtu() or ipv4_redirect().
This patch resolves this problem by using the IP protocol of the packet
rather than a hard-coded value. This appears to be consistent
with the usage of the protocol of a packet by icmp_socket_deliver()
the caller of ipip6_err().
I was able to exercise the redirect case by using a setup where an ICMP
redirect was received for the destination of the encapsulated packet.
However, it appears that although incorrect the protocol field is not used
in this case and thus no problem manifests. On inspection it does not
appear that a problem will manifest in the fragmentation needed/update pmtu
case either.
In short I believe this is a cosmetic fix. None the less, the use of
IPPROTO_IPV6 seems wrong and confusing.
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit daddef76c3 ]
The implementation of net_dbg_ratelimited in the CONFIG_DYNAMIC_DEBUG
case was added with 2c94b5373 ("net: Implement net_dbg_ratelimited() for
CONFIG_DYNAMIC_DEBUG case"). The implementation strategy was to take the
usual definition of the dynamic_pr_debug macro, but alter it by adding a
call to "net_ratelimit()" in the if statement. This is, in fact, the
correct approach.
However, while doing this, the author of the commit forgot to surround
fmt by pr_fmt, resulting in unprefixed log messages appearing in the
console. So, this commit adds back the pr_fmt(fmt) invocation, making
net_dbg_ratelimited properly consistent across DEBUG, no DEBUG, and
DYNAMIC_DEBUG cases, and bringing parity with the behavior of
dynamic_pr_debug as well.
Fixes: 2c94b5373 ("net: Implement net_dbg_ratelimited() for CONFIG_DYNAMIC_DEBUG case")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Tim Bingham <tbingham@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6c0d54f189 ]
When the qdisc is full, we drop a packet at the head of the queue,
queue the current skb and return NET_XMIT_CN
Now we track backlog on upper qdiscs, we need to call
qdisc_tree_reduce_backlog(), even if the qlen did not change.
Fixes: 2ccccf5fb4 ("net_sched: update hierarchical backlog too")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 79bb71bd1d upstream.
commit 54d77198fd
("gpio: bail out silently on NULL descriptors")
doesn't work for gpiod_to_irq(): drivers assume that NULL
descriptors will give negative IRQ numbers in return.
It has been pointed out that returning 0 is NO_IRQ and that
drivers should be amended to treat this as an error, but that
is for the longer term: now let us repair the semantics.
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Reported-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d7591f0c41 upstream.
The three variants use same copy&pasted code, condense this into a
helper and use that.
Make sure info.name is 0-terminated.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09d9686047 upstream.
This looks like refactoring, but its also a bug fix.
Problem is that the compat path (32bit iptables, 64bit kernel) lacks a few
sanity tests that are done in the normal path.
For example, we do not check for underflows and the base chain policies.
While its possible to also add such checks to the compat path, its more
copy&pastry, for instance we cannot reuse check_underflow() helper as
e->target_offset differs in the compat case.
Other problem is that it makes auditing for validation errors harder; two
places need to be checked and kept in sync.
At a high level 32 bit compat works like this:
1- initial pass over blob:
validate match/entry offsets, bounds checking
lookup all matches and targets
do bookkeeping wrt. size delta of 32/64bit structures
assign match/target.u.kernel pointer (points at kernel
implementation, needed to access ->compatsize etc.)
2- allocate memory according to the total bookkeeping size to
contain the translated ruleset
3- second pass over original blob:
for each entry, copy the 32bit representation to the newly allocated
memory. This also does any special match translations (e.g.
adjust 32bit to 64bit longs, etc).
4- check if ruleset is free of loops (chase all jumps)
5-first pass over translated blob:
call the checkentry function of all matches and targets.
The alternative implemented by this patch is to drop steps 3&4 from the
compat process, the translation is changed into an intermediate step
rather than a full 1:1 translate_table replacement.
In the 2nd pass (step #3), change the 64bit ruleset back to a kernel
representation, i.e. put() the kernel pointer and restore ->u.user.name .
This gets us a 64bit ruleset that is in the format generated by a 64bit
iptables userspace -- we can then use translate_table() to get the
'native' sanity checks.
This has two drawbacks:
1. we re-validate all the match and target entry structure sizes even
though compat translation is supposed to never generate bogus offsets.
2. we put and then re-lookup each match and target.
THe upside is that we get all sanity tests and ruleset validations
provided by the normal path and can remove some duplicated compat code.
iptables-restore time of autogenerated ruleset with 300k chains of form
-A CHAIN0001 -m limit --limit 1/s -j CHAIN0002
-A CHAIN0002 -m limit --limit 1/s -j CHAIN0003
shows no noticeable differences in restore times:
old: 0m30.796s
new: 0m31.521s
64bit: 0m25.674s
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b7eba0f35 upstream.
Quoting John Stultz:
In updating a 32bit arm device from 4.6 to Linus' current HEAD, I
noticed I was having some trouble with networking, and realized that
/proc/net/ip_tables_names was suddenly empty.
Digging through the registration process, it seems we're catching on the:
if (strcmp(t->u.user.name, XT_STANDARD_TARGET) == 0 &&
target_offset + sizeof(struct xt_standard_target) != next_offset)
return -EINVAL;
Where next_offset seems to be 4 bytes larger then the
offset + standard_target struct size.
next_offset needs to be aligned via XT_ALIGN (so we can access all members
of ip(6)t_entry struct).
This problem didn't show up on i686 as it only needs 4-byte alignment for
u64, but iptables userspace on other 32bit arches does insert extra padding.
Reported-by: John Stultz <john.stultz@linaro.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Fixes: 7ed2abddd2 ("netfilter: x_tables: check standard target size too")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 13631bfc60 upstream.
Validate that all matches (if any) add up to the beginning of
the target and that each match covers at least the base structure size.
The compat path should be able to safely re-use the function
as the structures only differ in alignment; added a
BUILD_BUG_ON just in case we have an arch that adds padding as well.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce683e5f9d upstream.
We're currently asserting that targetoff + targetsize <= nextoff.
Extend it to also check that targetoff is >= sizeof(xt_entry).
Since this is generic code, add an argument pointing to the start of the
match/target, we can then derive the base structure size from the delta.
We also need the e->elems pointer in a followup change to validate matches.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ed2abddd2 upstream.
We have targets and standard targets -- the latter carries a verdict.
The ip/ip6tables validation functions will access t->verdict for the
standard targets to fetch the jump offset or verdict for chainloop
detection, but this happens before the targets get checked/validated.
Thus we also need to check for verdict presence here, else t->verdict
can point right after a blob.
Spotted with UBSAN while testing malformed blobs.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc1221b3a1 upstream.
32bit rulesets have different layout and alignment requirements, so once
more integrity checks get added to xt_check_entry_offsets it will reject
well-formed 32bit rulesets.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aa412ba225 upstream.
Once we add more sanity testing to xt_check_entry_offsets it
becomes relvant if we're expecting a 32bit 'config_compat' blob
or a normal one.
Since we already have a lot of similar-named functions (check_entry,
compat_check_entry, find_and_check_entry, etc.) and the current
incarnation is short just fold its contents into the callers.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d35812c32 upstream.
Currently arp/ip and ip6tables each implement a short helper to check that
the target offset is large enough to hold one xt_entry_target struct and
that t->u.target_size fits within the current rule.
Unfortunately these checks are not sufficient.
To avoid adding new tests to all of ip/ip6/arptables move the current
checks into a helper, then extend this helper in followup patches.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3647234101 upstream.
When we see a jump also check that the offset gets us to beginning of
a rule (an ipt_entry).
The extra overhead is negible, even with absurd cases.
300k custom rules, 300k jumps to 'next' user chain:
[ plus one jump from INPUT to first userchain ]:
Before:
real 0m24.874s
user 0m7.532s
sys 0m16.076s
After:
real 0m27.464s
user 0m7.436s
sys 0m18.840s
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f24e230d25 upstream.
Ben Hawkes says:
In the mark_source_chains function (net/ipv4/netfilter/ip_tables.c) it
is possible for a user-supplied ipt_entry structure to have a large
next_offset field. This field is not bounds checked prior to writing a
counter value at the supplied offset.
Base chains enforce absolute verdict.
User defined chains are supposed to end with an unconditional return,
xtables userspace adds them automatically.
But if such return is missing we will move to non-existent next rule.
Reported-by: Ben Hawkes <hawkes@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f84f29ff3 upstream.
When the PM initialization was moved in the commit referenced below, the
code enabling the clock was removed from the probe function. On
CONFIG_PM=y kernels, this is not a problem as the pm resume hook enables
the clock, but when power management is disabled, all those pm_*
functions are noops and the clock is never enabled resulting in a
dysfunctional gpio controller.
Put the clock initialization back to support CONFIG_PM=n.
Signed-off-by: Helmut Grohne <h.grohne@intenta.de>
Fixes: 3773c195d3 ("gpio: zynq: Do PM initialization earlier to support gpio hogs")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7cafc0b8bf ]
We must handle data access exception as well as memory address unaligned
exceptions from return from trap window fill faults, not just normal
TLB misses.
Otherwise we can get an OOPS that looks like this:
ld-linux.so.2(36808): Kernel bad sw trap 5 [#1]
CPU: 1 PID: 36808 Comm: ld-linux.so.2 Not tainted 4.6.0 #34
task: fff8000303be5c60 ti: fff8000301344000 task.ti: fff8000301344000
TSTATE: 0000004410001601 TPC: 0000000000a1a784 TNPC: 0000000000a1a788 Y: 00000002 Not tainted
TPC: <do_sparc64_fault+0x5c4/0x700>
g0: fff8000024fc8248 g1: 0000000000db04dc g2: 0000000000000000 g3: 0000000000000001
g4: fff8000303be5c60 g5: fff800030e672000 g6: fff8000301344000 g7: 0000000000000001
o0: 0000000000b95ee8 o1: 000000000000012b o2: 0000000000000000 o3: 0000000200b9b358
o4: 0000000000000000 o5: fff8000301344040 sp: fff80003013475c1 ret_pc: 0000000000a1a77c
RPC: <do_sparc64_fault+0x5bc/0x700>
l0: 00000000000007ff l1: 0000000000000000 l2: 000000000000005f l3: 0000000000000000
l4: fff8000301347e98 l5: fff8000024ff3060 l6: 0000000000000000 l7: 0000000000000000
i0: fff8000301347f60 i1: 0000000000102400 i2: 0000000000000000 i3: 0000000000000000
i4: 0000000000000000 i5: 0000000000000000 i6: fff80003013476a1 i7: 0000000000404d4c
I7: <user_rtt_fill_fixup+0x6c/0x7c>
Call Trace:
[0000000000404d4c] user_rtt_fill_fixup+0x6c/0x7c
The window trap handlers are slightly clever, the trap table entries for them are
composed of two pieces of code. First comes the code that actually performs
the window fill or spill trap handling, and then there are three instructions at
the end which are for exception processing.
The userland register window fill handler is:
add %sp, STACK_BIAS + 0x00, %g1; \
ldxa [%g1 + %g0] ASI, %l0; \
mov 0x08, %g2; \
mov 0x10, %g3; \
ldxa [%g1 + %g2] ASI, %l1; \
mov 0x18, %g5; \
ldxa [%g1 + %g3] ASI, %l2; \
ldxa [%g1 + %g5] ASI, %l3; \
add %g1, 0x20, %g1; \
ldxa [%g1 + %g0] ASI, %l4; \
ldxa [%g1 + %g2] ASI, %l5; \
ldxa [%g1 + %g3] ASI, %l6; \
ldxa [%g1 + %g5] ASI, %l7; \
add %g1, 0x20, %g1; \
ldxa [%g1 + %g0] ASI, %i0; \
ldxa [%g1 + %g2] ASI, %i1; \
ldxa [%g1 + %g3] ASI, %i2; \
ldxa [%g1 + %g5] ASI, %i3; \
add %g1, 0x20, %g1; \
ldxa [%g1 + %g0] ASI, %i4; \
ldxa [%g1 + %g2] ASI, %i5; \
ldxa [%g1 + %g3] ASI, %i6; \
ldxa [%g1 + %g5] ASI, %i7; \
restored; \
retry; nop; nop; nop; nop; \
b,a,pt %xcc, fill_fixup_dax; \
b,a,pt %xcc, fill_fixup_mna; \
b,a,pt %xcc, fill_fixup;
And the way this works is that if any of those memory accesses
generate an exception, the exception handler can revector to one of
those final three branch instructions depending upon which kind of
exception the memory access took. In this way, the fault handler
doesn't have to know if it was a spill or a fill that it's handling
the fault for. It just always branches to the last instruction in
the parent trap's handler.
For example, for a regular fault, the code goes:
winfix_trampoline:
rdpr %tpc, %g3
or %g3, 0x7c, %g3
wrpr %g3, %tnpc
done
All window trap handlers are 0x80 aligned, so if we "or" 0x7c into the
trap time program counter, we'll get that final instruction in the
trap handler.
On return from trap, we have to pull the register window in but we do
this by hand instead of just executing a "restore" instruction for
several reasons. The largest being that from Niagara and onward we
simply don't have enough levels in the trap stack to fully resolve all
possible exception cases of a window fault when we are already at
trap level 1 (which we enter to get ready to return from the original
trap).
This is executed inline via the FILL_*_RTRAP handlers. rtrap_64.S's
code branches directly to these to do the window fill by hand if
necessary. Now if you look at them, we'll see at the end:
ba,a,pt %xcc, user_rtt_fill_fixup;
ba,a,pt %xcc, user_rtt_fill_fixup;
ba,a,pt %xcc, user_rtt_fill_fixup;
And oops, all three cases are handled like a fault.
This doesn't work because each of these trap types (data access
exception, memory address unaligned, and faults) store their auxiliary
info in different registers to pass on to the C handler which does the
real work.
So in the case where the stack was unaligned, the unaligned trap
handler sets up the arg registers one way, and then we branched to
the fault handler which expects them setup another way.
So the FAULT_TYPE_* value ends up basically being garbage, and
randomly would generate the backtrace seen above.
Reported-by: Nick Alcock <nix@esperi.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d11c2a0de2 ]
All signal frames must be at least 16-byte aligned, because that is
the alignment we explicitly create when we build signal return stack
frames.
All stack pointers must be at least 8-byte aligned.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9ea46abe22 ]
On cheetahplus chips we take the ctx_alloc_lock in order to
modify the TLB lookup parameters for the indexed TLBs, which
are stored in the context register.
This is called with interrupts disabled, however ctx_alloc_lock
is an IRQ safe lock, therefore we must take acquire/release it
properly with spin_{lock,unlock}_irq().
Reported-by: Meelis Roos <mroos@linux.ee>
Tested-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 24e49ee3d7 ]
During hugepage map/unmap, TSB and TLB flushes are currently
issued at every PAGE_SIZE'd boundary which is unnecessary.
We now issue the flush at REAL_HPAGE_SIZE boundaries only.
Without this patch workloads which unmap a large hugepage
backed VMA region get CPU lockups due to excessive TLB
flush calls.
Orabug: 22365539, 22643230, 22995196
Signed-off-by: Nitin Gupta <nitin.m.gupta@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d56c25e3b upstream.
Ascend-to-parent logics in d_walk() depends on all encountered child
dentries not getting freed without an RCU delay. Unfortunately, in
quite a few cases it is not true, with hard-to-hit oopsable race as
the result.
Fortunately, the fix is simiple; right now the rule is "if it ever
been hashed, freeing must be delayed" and changing it to "if it
ever had a parent, freeing must be delayed" closes that hole and
covers all cases the old rule used to cover. Moreover, pipes and
sockets remain _not_ covered, so we do not introduce RCU delay in
the cases which are the reason for having that delay conditional
in the first place.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 29d6455178 upstream.
Until now, hitting this BUG_ON caused a recursive oops (because oops
handling involves do_exit(), which calls into the scheduler, which in
turn raises an oops), which caused stuff below the stack to be
overwritten until a panic happened (e.g. via an oops in interrupt
context, caused by the overwritten CPU index in the thread_info).
Just panic directly.
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e54ad7f1ee upstream.
This prevents stacking filesystems (ecryptfs and overlayfs) from using
procfs as lower filesystem. There is too much magic going on inside
procfs, and there is no good reason to stack stuff on top of procfs.
(For example, procfs does access checks in VFS open handlers, and
ecryptfs by design calls open handlers from a kernel thread that doesn't
drop privileges or so.)
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 770a537022 upstream.
Christian Borntraeger reported a kernel panic after corrupt page counts,
and it turned out to be a regression introduced with commit aa88b68c3b
("thp: keep huge zero page pinned until tlb flush"), at least on s390.
put_huge_zero_page() was moved over from zap_huge_pmd() to
release_pages(), and it was replaced by tlb_remove_page(). However,
release_pages() might not always be triggered by (the arch-specific)
tlb_remove_page().
On s390 we call free_page_and_swap_cache() from tlb_remove_page(), and
not tlb_flush_mmu() -> free_pages_and_swap_cache() like the generic
version, because we don't use the MMU-gather logic. Although both
functions have very similar names, they are doing very unsimilar things,
in particular free_page_xxx is just doing a put_page(), while
free_pages_xxx calls release_pages().
This of course results in very harmful put_page()s on the huge zero
page, on architectures where tlb_remove_page() is implemented in this
way. It seems to affect only s390 and sh, but sh doesn't have THP
support, so the problem (currently) probably only exists on s390.
The following quick hack fixed the issue:
Link: http://lkml.kernel.org/r/20160602172141.75c006a9@thinkpad
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Reported-by: Christian Borntraeger <borntraeger@de.ibm.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Hugh Dickins <hughd@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d5fdff46c upstream.
iwpriv app uses iw_point structure to send data to Kernel. The iw_point
structure holds a pointer. For compatibility Kernel converts the pointer
as required for WEXT IOCTLs (SIOCIWFIRST to SIOCIWLAST). Some drivers
may use iw_handler_def.private_args to populate iwpriv commands instead
of iw_handler_def.private. For those case, the IOCTLs from
SIOCIWFIRSTPRIV to SIOCIWLASTPRIV will follow the path ndo_do_ioctl().
Accordingly when the filled up iw_point structure comes from 32 bit
iwpriv to 64 bit Kernel, Kernel will not convert the pointer and sends
it to driver. So, the driver may get the invalid data.
The pointer conversion for the IOCTLs (SIOCIWFIRSTPRIV to
SIOCIWLASTPRIV), which follow the path ndo_do_ioctl(), is mandatory.
This patch adds pointer conversion from 32 bit to 64 bit and vice versa,
if the ioctl comes from 32 bit iwpriv to 64 bit Kernel.
Signed-off-by: Prasun Maiti <prasunmaiti87@gmail.com>
Signed-off-by: Ujjal Roy <royujjal@gmail.com>
Tested-by: Dibyajyoti Ghosh <dibyajyotig@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a06bb78ce upstream.
memcg_offline_kmem() may be called from memcg_free_kmem() after a css
init failure. memcg_free_kmem() is a ->css_free callback which is
called without cgroup_mutex and memcg_offline_kmem() ends up using
css_for_each_descendant_pre() without any locking. Fix it by adding rcu
read locking around it.
mkdir: cannot create directory `65530': No space left on device
===============================
[ INFO: suspicious RCU usage. ]
4.6.0-work+ #321 Not tainted
-------------------------------
kernel/cgroup.c:4008 cgroup_mutex or RCU read lock required!
[ 527.243970] other info that might help us debug this:
[ 527.244715]
rcu_scheduler_active = 1, debug_locks = 0
2 locks held by kworker/0:5/1664:
#0: ("cgroup_destroy"){.+.+..}, at: [<ffffffff81060ab5>] process_one_work+0x165/0x4a0
#1: ((&css->destroy_work)#3){+.+...}, at: [<ffffffff81060ab5>] process_one_work+0x165/0x4a0
[ 527.248098] stack backtrace:
CPU: 0 PID: 1664 Comm: kworker/0:5 Not tainted 4.6.0-work+ #321
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.9.1-1.fc24 04/01/2014
Workqueue: cgroup_destroy css_free_work_fn
Call Trace:
dump_stack+0x68/0xa1
lockdep_rcu_suspicious+0xd7/0x110
css_next_descendant_pre+0x7d/0xb0
memcg_offline_kmem.part.44+0x4a/0xc0
mem_cgroup_css_free+0x1ec/0x200
css_free_work_fn+0x49/0x5e0
process_one_work+0x1c5/0x4a0
worker_thread+0x49/0x490
kthread+0xea/0x100
ret_from_fork+0x1f/0x40
Link: http://lkml.kernel.org/r/20160526203018.GG23194@mtj.duckdns.org
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b78f26088 upstream.
One of the debian buildd servers had this crash in the syslog without
any other information:
Unaligned handler failed, ret = -2
clock_adjtime (pid 22578): Unaligned data reference (code 28)
CPU: 1 PID: 22578 Comm: clock_adjtime Tainted: G E 4.5.0-2-parisc64-smp #1 Debian 4.5.4-1
task: 000000007d9960f8 ti: 00000001bde7c000 task.ti: 00000001bde7c000
YZrvWESTHLNXBCVMcbcbcbcbOGFRQPDI
PSW: 00001000000001001111100000001111 Tainted: G E
r00-03 000000ff0804f80f 00000001bde7c2b0 00000000402d2be8 00000001bde7c2b0
r04-07 00000000409e1fd0 00000000fa6f7fff 00000001bde7c148 00000000fa6f7fff
r08-11 0000000000000000 00000000ffffffff 00000000fac9bb7b 000000000002b4d4
r12-15 000000000015241c 000000000015242c 000000000000002d 00000000fac9bb7b
r16-19 0000000000028800 0000000000000001 0000000000000070 00000001bde7c218
r20-23 0000000000000000 00000001bde7c210 0000000000000002 0000000000000000
r24-27 0000000000000000 0000000000000000 00000001bde7c148 00000000409e1fd0
r28-31 0000000000000001 00000001bde7c320 00000001bde7c350 00000001bde7c218
sr00-03 0000000001200000 0000000001200000 0000000000000000 0000000001200000
sr04-07 0000000000000000 0000000000000000 0000000000000000 0000000000000000
IASQ: 0000000000000000 0000000000000000 IAOQ: 00000000402d2e84 00000000402d2e88
IIR: 0ca0d089 ISR: 0000000001200000 IOR: 00000000fa6f7fff
CPU: 1 CR30: 00000001bde7c000 CR31: ffffffffffffffff
ORIG_R28: 00000002369fe628
IAOQ[0]: compat_get_timex+0x2dc/0x3c0
IAOQ[1]: compat_get_timex+0x2e0/0x3c0
RP(r2): compat_get_timex+0x40/0x3c0
Backtrace:
[<00000000402d4608>] compat_SyS_clock_adjtime+0x40/0xc0
[<0000000040205024>] syscall_exit+0x0/0x14
This means the userspace program clock_adjtime called the clock_adjtime()
syscall and then crashed inside the compat_get_timex() function.
Syscalls should never crash programs, but instead return EFAULT.
The IIR register contains the executed instruction, which disassebles
into "ldw 0(sr3,r5),r9".
This load-word instruction is part of __get_user() which tried to read the word
at %r5/IOR (0xfa6f7fff). This means the unaligned handler jumped in. The
unaligned handler is able to emulate all ldw instructions, but it fails if it
fails to read the source e.g. because of page fault.
The following program reproduces the problem:
#define _GNU_SOURCE
#include <unistd.h>
#include <sys/syscall.h>
#include <sys/mman.h>
int main(void) {
/* allocate 8k */
char *ptr = mmap(NULL, 2*4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0);
/* free second half (upper 4k) and make it invalid. */
munmap(ptr+4096, 4096);
/* syscall where first int is unaligned and clobbers into invalid memory region */
/* syscall should return EFAULT */
return syscall(__NR_clock_adjtime, 0, ptr+4095);
}
To fix this issue we simply need to check if the faulting instruction address
is in the exception fixup table when the unaligned handler failed. If it
is, call the fixup routine instead of crashing.
While looking at the unaligned handler I found another issue as well: The
target register should not be modified if the handler was unsuccessful.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5edf673d07 upstream.
When a dual-edge irq is triggered, an incorrect irq will be reported on
condition that the external signal is not stable and this incorrect irq
has been registered.
Correct the register offset.
Signed-off-by: Hongkun Cao <hongkun.cao@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc47c0c1f8 upstream.
When we converted the asm routines to C functions, we missed updating
HPTE_R_R based on _PAGE_ACCESSED. ASM code used to copy over the lower
bits from pte via.
andi. r3,r30,0x1fe /* Get basic set of flags */
We also update the code such that we won't update the Change bit ('C'
bit) always. This was added by commit c5cf0e30bf ("powerpc: Fix
buglet with MMU hash management").
With hash64, we need to make sure that hardware doesn't do a pte update
directly. This is because we do end up with entries in TLB with no hash
page table entry. This happens because when we find a hash bucket full,
we "evict" a more/less random entry from it. When we do that we don't
invalidate the TLB (hpte_remove) because we assume the old translation
is still technically "valid". For more info look at commit
0608d692463("powerpc/mm: Always invalidate tlb on hpte invalidate and
update").
Thus it's critical that valid hash PTEs always have reference bit set
and writeable ones have change bit set. We do this by hashing a
non-dirty linux PTE as read-only and always setting _PAGE_ACCESSED (and
thus R) when hashing anything else in. Any attempt by Linux at clearing
those bits also removes the corresponding hash entry.
Commit 5cf0e30bf3d8 did that for 'C' bit by enabling 'C' bit always.
We don't really need to do that because we never map a RW pte entry
without setting 'C' bit. On READ fault on a RW pte entry, we still map
it READ only, hence a store update in the page will still cause a hash
pte fault.
This patch reverts the part of commit c5cf0e30bf ("[PATCH] powerpc:
Fix buglet with MMU hash management") and retain the updatepp part.
- If we hit the updatepp path on native, the old code without that
commit, would fail to set C bcause native_hpte_updatepp()
was implemented to filter the same bits as H_PROTECT and not let C
through thus we would "upgrade" a RO HPTE to RW without setting C
thus causing the bug. So the real fix in that commit was the change
to native_hpte_updatepp
Fixes: 89ff725051 ("powerpc/mm: Convert __hash_page_64K to C")
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7cc851039d upstream.
If we do not provide the PVR for POWER8NVL, a guest on this system
currently ends up in PowerISA 2.06 compatibility mode on KVM, since QEMU
does not provide a generic PowerISA 2.07 mode yet. So some new
instructions from POWER8 (like "mtvsrd") get disabled for the guest,
resulting in crashes when using code compiled explicitly for
POWER8 (e.g. with the "-mcpu=power8" option of GCC).
Fixes: ddee09c099 ("powerpc: Add PVR for POWER8NVL processor")
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8dd75ccb57 upstream.
We are already using the privileged versions of MMCR0, MMCR1
and MMCRA in the kernel, so for MMCR2, we should better use
the privileged versions, too, to be consistent.
Fixes: 240686c136 ("powerpc: Initialise PMU related regs on Power8")
Suggested-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Acked-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d23fac2b27 upstream.
The SIAR and SDAR registers are available twice, one time as SPRs
780 / 781 (unprivileged, but read-only), and one time as the SPRs
796 / 797 (privileged, but read and write). The Linux kernel code
currently uses the unprivileged SPRs - while this is OK for reading,
writing to that register of course does not work.
Since the KVM code tries to write to this register, too (see the mtspr
in book3s_hv_rmhandlers.S), the contents of this register sometimes get
lost for the guests, e.g. during migration of a VM.
To fix this issue, simply switch to the privileged SPR numbers instead.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Acked-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 871e178e0f upstream.
In the "ibm,configure-pe" and "ibm,configure-bridge" RTAS calls, the
spec states that values of 9900-9905 can be returned, indicating that
software should delay for 10^x (where x is the last digit, i.e. 990x)
milliseconds and attempt the call again. Currently, the kernel doesn't
know about this, and respecting it fixes some PCI failures when the
hypervisor is busy.
The delay is capped at 0.2 seconds.
Signed-off-by: Russell Currey <ruscur@russell.cc>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0106d456c4 upstream.
Commit 66dbd6e61a ("arm64: Implement ptep_set_access_flags() for
hardware AF/DBM") ensured that pte flags are updated atomically in the
face of potential concurrent, hardware-assisted updates. However, Alex
reports that:
| This patch breaks swapping for me.
| In the broken case, you'll see either systemd cpu time spike (because
| it's stuck in a page fault loop) or the system hang (because the
| application owning the screen is stuck in a page fault loop).
It turns out that this is because the 'dirty' argument to
ptep_set_access_flags is always 0 for read faults, and so we can't use
it to set PTE_RDONLY. The failing sequence is:
1. We put down a PTE_WRITE | PTE_DIRTY | PTE_AF pte
2. Memory pressure -> pte_mkold(pte) -> clear PTE_AF
3. A read faults due to the missing access flag
4. ptep_set_access_flags is called with dirty = 0, due to the read fault
5. pte is then made PTE_WRITE | PTE_DIRTY | PTE_AF | PTE_RDONLY (!)
6. A write faults, but pte_write is true so we get stuck
The solution is to check the new page table entry (as would be done by
the generic, non-atomic definition of ptep_set_access_flags that just
calls set_pte_at) to establish the dirty state.
Fixes: 66dbd6e61a ("arm64: Implement ptep_set_access_flags() for hardware AF/DBM")
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Alexander Graf <agraf@suse.de>
Tested-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e47b020a32 upstream.
This patch brings the PER_LINUX32 /proc/cpuinfo format more in line with
the 32-bit ARM one by providing an additional line:
model name : ARMv8 Processor rev X (v8l)
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ab6a11a7c8 upstream.
The ccp-crypto module for AES XTS support has a bug that can allow requests
greater than 4096 bytes in size to be passed to the CCP hardware. The CCP
hardware does not support request sizes larger than 4096, resulting in
incorrect output. The request should actually be handled by the fallback
mechanism instantiated by the ccp-crypto module.
Add a check to insure the request size is less than or equal to the maximum
supported size and use the fallback mechanism if it is not.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bad6a185b4 upstream.
In some rare randconfig builds, we can end up with
ASYMMETRIC_PUBLIC_KEY_SUBTYPE enabled but CRYPTO_AKCIPHER disabled,
which fails to link because of the reference to crypto_alloc_akcipher:
crypto/built-in.o: In function `public_key_verify_signature':
:(.text+0x110e4): undefined reference to `crypto_alloc_akcipher'
This adds a Kconfig 'select' statement to ensure the dependency
is always there.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd5f1b049d upstream.
The INTID mask is wrong, and is made a signed value, which has
nteresting effects in the KVM emulation. Let's sanitize it.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0fa963553a upstream.
The s390 BFP compiler currently uses relative branch instructions
that only support jumps up to 64 KB. Examples are "j", "jnz", "cgrj",
etc. Currently the maximum size of s390 BPF programs is set
to 0x7ffff. If branches over 64 KB are generated the, kernel can
crash due to incorrect code.
So fix this an reduce the maximum size to 64 KB. Programs larger than
that will be interpreted.
Fixes: ce2b6ad9c1 ("s390/bpf: increase BPF_SIZE_MAX")
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6edf0aa4f8 upstream.
In case of usage of skb_vlan_push/pop, in the prologue we store
the SKB pointer on the stack and restore it after BPF_JMP_CALL
to skb_vlan_push/pop.
Unfortunately currently there are two bugs in the code:
1) The wrong stack slot (offset 170 instead of 176) is used
2) The wrong register (W1 instead of B1) is saved
So fix this and use correct stack slot and register.
Fixes: 9db7f2b818 ("s390/bpf: recache skb->data/hlen for skb_vlan_push/pop")
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f4833b8cc7 upstream.
gpiolib relies on the reference counters to clean up the gpio_device
structure.
Although the number of get/put is properly aligned on gpiolib.c
itself, it does not take into consideration how the referece counters
are affected by other external functions such as cdev_add and device_add.
Because of this, after the last call to put_device, the reference counter
has a value of +3, therefore never calling gpiodevice_release.
Due to the fact that some of the device has already been cleaned on
gpiochip_remove, the library will end up OOPsing the kernel (e.g. a call
to of_gpiochip_find_and_xlate).
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 11f33a6d15 upstream.
Under some circumstances, a gpiochip might be half cleaned from the
gpio_device list.
This patch makes sure that the chip pointer is still valid, before
calling the match function.
[ 104.088296] BUG: unable to handle kernel NULL pointer dereference at
0000000000000090
[ 104.089772] IP: [<ffffffff813d2045>] of_gpiochip_find_and_xlate+0x15/0x80
[ 104.128273] Call Trace:
[ 104.129802] [<ffffffff813d2030>] ? of_parse_own_gpio+0x1f0/0x1f0
[ 104.131353] [<ffffffff813cd910>] gpiochip_find+0x60/0x90
[ 104.132868] [<ffffffff813d21ba>] of_get_named_gpiod_flags+0x9a/0x120
...
[ 104.141586] [<ffffffff8163d12b>] gpio_led_probe+0x11b/0x360
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b66b2a0adf upstream.
The bcm_kona_gpio_reset() calls bcm_kona_gpio_write_lock_regs()
with what looks like the wrong parameter. The write_lock_regs
function takes a pointer to the registers, not the bcm_kona_gpio
structure.
Fix the warning, and probably bug by changing the function to
pass reg_base instead of kona_gpio, fixing the following warning:
drivers/gpio/gpio-bcm-kona.c:550:47: warning: incorrect type in argument 1
(different address spaces)
expected void [noderef] <asn:2>*reg_base
got struct bcm_kona_gpio *kona_gpio
warning: incorrect type in argument 1 (different address spaces)
expected void [noderef] <asn:2>*reg_base
got struct bcm_kona_gpio *kona_gpio
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Markus Mayer <mmayer@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e2dfb4b880 upstream.
PTRACE_SETVFPREGS fails to properly mark the VFP register set to be
reloaded, because it undoes one of the effects of vfp_flush_hwstate().
Specifically vfp_flush_hwstate() sets thread->vfpstate.hard.cpu to
an invalid CPU number, but vfp_set() overwrites this with the original
CPU number, thereby rendering the hardware state as apparently "valid",
even though the software state is more recent.
Fix this by reverting the previous change.
Fixes: 8130b9d7b9 ("ARM: 7308/1: vfp: flush thread hwstate before copying ptrace registers")
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Simon Marchi <simon.marchi@ericsson.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e69e7e03ed upstream.
That is some different register for ALC255 and ALC256.
ALC256 can't fit with some ALC255 register.
This issue is cause from LDO output voltage control.
This patch is updated the right LDO register value.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f90d83b301 upstream.
Add the pin configuration value of this machine into the pin_quirk
table to make DELL1_MIC_NO_PRESENCE apply to this machine.
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 35639a0e98 upstream.
Kabylake shows up as PCI ID 0xa171. And Kabylake-LP as 0x9d71.
Since these are similar to Skylake add these to SKL_PLUS macro
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f254c7671 upstream.
The global variable __oprofile_cpu_pmu is set before the PMU is fully
initialized. If an error occurs before the end of the initialization,
the PMU will be freed and the variable will contain an invalid pointer.
This will result in a kernel crash when perf will be used.
Fix it by moving the setting of __oprofile_cpu_pmu when the PMU is fully
initialized (i.e when it is no longer possible to fail).
Signed-off-by: Julien Grall <julien.grall@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fa89c77e89 upstream.
When saving the state of the list registers, it is critical to
reset them zero, as we could otherwise leave unexpected EOI
interrupts pending for virtual level interrupts.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4d3afc9bad upstream.
When saving the state of the list registers, it is critical to
reset them zero, as we could otherwise leave unexpected EOI
interrupts pending for virtual level interrupts.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 00bc0ef588 ]
At present we perform an xfrm_lookup() for each UDPv6 message we
send. The lookup involves querying the flow cache (flow_cache_lookup)
and, in case of a cache miss, creating an XFRM bundle.
If we miss the flow cache, we can end up creating a new bundle and
deriving the path MTU (xfrm_init_pmtu) from on an already transformed
dst_entry, which we pass from the socket cache (sk->sk_dst_cache) down
to xfrm_lookup(). This can happen only if we're caching the dst_entry
in the socket, that is when we're using a connected UDP socket.
To put it another way, the path MTU shrinks each time we miss the flow
cache, which later on leads to incorrectly fragmented payload. It can
be observed with ESPv6 in transport mode:
1) Set up a transformation and lower the MTU to trigger fragmentation
# ip xfrm policy add dir out src ::1 dst ::1 \
tmpl src ::1 dst ::1 proto esp spi 1
# ip xfrm state add src ::1 dst ::1 \
proto esp spi 1 enc 'aes' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b
# ip link set dev lo mtu 1500
2) Monitor the packet flow and set up an UDP sink
# tcpdump -ni lo -ttt &
# socat udp6-listen:12345,fork /dev/null &
3) Send a datagram that needs fragmentation with a connected socket
# perl -e 'print "@" x 1470 | socat - udp6:[::1]:12345
2016/06/07 18:52:52 socat[724] E read(3, 0x555bb3d5ba00, 8192): Protocol error
00:00:00.000000 IP6 ::1 > ::1: frag (0|1448) ESP(spi=0x00000001,seq=0x2), length 1448
00:00:00.000014 IP6 ::1 > ::1: frag (1448|32)
00:00:00.000050 IP6 ::1 > ::1: ESP(spi=0x00000001,seq=0x3), length 1272
(^ ICMPv6 Parameter Problem)
00:00:00.000022 IP6 ::1 > ::1: ESP(spi=0x00000001,seq=0x5), length 136
4) Compare it to a non-connected socket
# perl -e 'print "@" x 1500' | socat - udp6-sendto:[::1]:12345
00:00:40.535488 IP6 ::1 > ::1: frag (0|1448) ESP(spi=0x00000001,seq=0x6), length 1448
00:00:00.000010 IP6 ::1 > ::1: frag (1448|64)
What happens in step (3) is:
1) when connecting the socket in __ip6_datagram_connect(), we
perform an XFRM lookup, miss the flow cache, create an XFRM
bundle, and cache the destination,
2) afterwards, when sending the datagram, we perform an XFRM lookup,
again, miss the flow cache (due to mismatch of flowi6_iif and
flowi6_oif, which is an issue of its own), and recreate an XFRM
bundle based on the cached (and already transformed) destination.
To prevent the recreation of an XFRM bundle, avoid an XFRM lookup
altogether whenever we already have a destination entry cached in the
socket. This prevents the path MTU shrinkage and brings us on par with
UDPv4.
The fix also benefits connected PINGv6 sockets, another user of
ip6_sk_dst_lookup_flow(), who also suffer messages being transformed
twice.
Joint work with Hannes Frederic Sowa.
Reported-by: Jan Tluka <jtluka@redhat.com>
Signed-off-by: Jakub Sitnicki <jkbs@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0b148def40 ]
The missing br_vlan_should_use() test caused creation of an unneeded
local fdb entry on changing mac address of a bridge device when there is
a vlan which is configured on a bridge port but not on the bridge
device.
Fixes: 2594e9064a ("bridge: vlan: add per-vlan struct and move to rhashtables")
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ce3cf4ec03 ]
The v6 tcp stats scan do not provide TLP and ER timer information
correctly like the v4 version . This patch fixes that.
Fixes: 6ba8a3b19e ("tcp: Tail loss probe (TLP)")
Fixes: eed530b6c6 ("tcp: early retransmit")
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5b6c1b4d46 ]
In bpf_perf_event_read() and bpf_perf_event_output(), we must use
READ_ONCE() for fetching the struct file pointer, which could get
updated concurrently, so we must prevent the compiler from potential
refetching.
We already do this with tail calls for fetching the related bpf_prog,
but not so on stored perf events. Semantics for both are the same
with regards to updates.
Fixes: a43eec3042 ("bpf: introduce bpf_perf_event_output() helper")
Fixes: 35578d7984 ("bpf: Implement function bpf_perf_event_read() that get the selected hardware PMU conuter")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 86651650d1 ]
Since NAPI works by shutting down event interrupts when theres
work and turning them on when theres none, the net driver must
make sure that interrupts are disabled when it reschedules polling.
By calling napi_reschedule, the driver switches to polling mode,
therefor there should be no interrupt interference.
Any received packets will be handled in nps_enet_poll by polling the HW
indication of received packet until all packets are handled.
Signed-off-by: Elad Kanfi <eladkan@mellanox.com>
Acked-by: Noam Camus <noamca@mellanox.com>
Tested-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ce577668a4 ]
When create a new vxlan link, example:
ip link add vtap mtu 1440 type vxlan vni 1 dev eth0
The argument "mtu" has no effect, because it is not set to conf->mtu. The
default value is used in vxlan_dev_configure function.
This problem was introduced by commit 0dfbdf4102 (vxlan: Factor out device
configuration).
Fixes: 0dfbdf4102 (vxlan: Factor out device configuration)
Signed-off-by: Chen Haiquan <oc@yunify.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 643d60bf57 ]
The memcpy() currently copies mdio_bus_data into new_bus->irq, which
makes no sense, since the mdio_bus_data structure contains more than
just irqs. The code was likely supposed to copy mdio_bus_data->irqs
into the new_bus->irq instead, so fix this.
Fixes: e7f4dc3536 ("mdio: Move allocation of interrupts into core")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 26c5f03b2a ]
This patch follows Eric Dumazet's commit 7b70176421 for Atheros
atl1c driver to fix one exactly same bug in alx driver, that the
network link will be lost in 1-5 minutes after the device is up.
My laptop Lenovo Y580 with Atheros AR8161 ethernet device hit the
same problem with kernel 4.4, and it will be cured by Jarod Wilson's
commit c406700c for alx driver which get merged in 4.5. But there
are still some alx devices can't function well even with Jarod's
patch, while this patch could make them work fine. More details on
https://bugzilla.kernel.org/show_bug.cgi?id=70761
The debug shows the issue is very likely to be related with the RX
DMA address, specifically 0x...f80, if RX buffer get 0x...f80 several
times, their will be RX overflow error and device will stop working.
For kernel 4.5.0 with Jarod's patch which works fine with my
AR8161/Lennov Y580, if I made some change to the
__netdev_alloc_skb
--> __alloc_page_frag()
to make the allocated buffer can get an address with 0x...f80,
then the same error happens. If I make it to 0x...f40 or 0x....fc0,
everything will be still fine. So I tend to believe that the
0x..f80 address cause the silicon to behave abnormally.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=70761
Cc: Eric Dumazet <edumazet@google.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Feng Tang <feng.tang@intel.com>
Tested-by: Ole Lukoie <olelukoie@mail.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f6988cb63a ]
The team_device_event() notifier calls team_compute_features() to fix
vlan_features under team->lock to protect team->port_list. The problem is
that subsequent __team_compute_features() calls netdev_change_features()
to propagate vlan_features to upper vlan devices while team->lock is still
taken. This can lead to deadlock when NETIF_F_LRO is modified on lower
devices or team device itself.
Example:
The team0 as active backup with eth0 and eth1 NICs. Both eth0 & eth1 are
LRO capable and LRO is enabled. Thus LRO is also enabled on team0.
The command 'ethtool -K team0 lro off' now hangs due to this deadlock:
dev_ethtool()
-> ethtool_set_features()
-> __netdev_update_features(team)
-> netdev_sync_lower_features()
-> netdev_update_features(lower_1)
-> __netdev_update_features(lower_1)
-> netdev_features_change(lower_1)
-> call_netdevice_notifiers(...)
-> team_device_event(lower_1)
-> team_compute_features(team) [TAKES team->lock]
-> netdev_change_features(team)
-> __netdev_update_features(team)
-> netdev_sync_lower_features()
-> netdev_update_features(lower_2)
-> __netdev_update_features(lower_2)
-> netdev_features_change(lower_2)
-> call_netdevice_notifiers(...)
-> team_device_event(lower_2)
-> team_compute_features(team) [DEADLOCK]
The bug is present in team from the beginning but it appeared after the commit
fd867d5 (net/core: generic support for disabling netdev features down stack)
that adds synchronization of features with lower devices.
Fixes: fd867d5 (net/core: generic support for disabling netdev features down stack)
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c0795bf64c ]
Otherwise, if we fail to allocate new PIO buffers, our TXQs will try to
use the old ones, which aren't there any more.
Fixes: 183233bec8 "sfc: Allocate and link PIO buffers; map them with write-combining"
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 91c45e38b9 ]
The spinlock used by the hwbm functions must be initialized by the
network driver. This commit fixes this lack and the following erros when
lockdep is enabled:
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
[<c010ff80>] (unwind_backtrace) from [<c010bd08>] (show_stack+0x10/0x14)
[<c010bd08>] (show_stack) from [<c032913c>] (dump_stack+0xb4/0xe0)
[<c032913c>] (dump_stack) from [<c01670e4>] (__lock_acquire+0x1f58/0x2060)
[<c01670e4>] (__lock_acquire) from [<c0167dec>] (lock_acquire+0xa4/0xd0)
[<c0167dec>] (lock_acquire) from [<c06f6650>] (_raw_spin_lock_irqsave+0x54/0x68)
[<c06f6650>] (_raw_spin_lock_irqsave) from [<c058e830>] (hwbm_pool_add+0x1c/0xdc)
[<c058e830>] (hwbm_pool_add) from [<c043f4e8>] (mvneta_bm_pool_use+0x338/0x490)
[<c043f4e8>] (mvneta_bm_pool_use) from [<c0443198>] (mvneta_probe+0x654/0x1284)
[<c0443198>] (mvneta_probe) from [<c03b894c>] (platform_drv_probe+0x4c/0xb0)
[<c03b894c>] (platform_drv_probe) from [<c03b7158>] (driver_probe_device+0x214/0x2c0)
[<c03b7158>] (driver_probe_device) from [<c03b72c4>] (__driver_attach+0xc0/0xc4)
[<c03b72c4>] (__driver_attach) from [<c03b5440>] (bus_for_each_dev+0x68/0x9c)
[<c03b5440>] (bus_for_each_dev) from [<c03b65b8>] (bus_add_driver+0x1a0/0x218)
[<c03b65b8>] (bus_add_driver) from [<c03b79cc>] (driver_register+0x78/0xf8)
[<c03b79cc>] (driver_register) from [<c01018f4>] (do_one_initcall+0x90/0x1dc)
[<c01018f4>] (do_one_initcall) from [<c0900de4>] (kernel_init_freeable+0x15c/0x1fc)
[<c0900de4>] (kernel_init_freeable) from [<c06eed90>] (kernel_init+0x8/0x114)
[<c06eed90>] (kernel_init) from [<c0107910>] (ret_from_fork+0x14/0x24)
Fixes: baa11ebc0c ("net: mvneta: Use the new hwbm framework")
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 612bacad78 ]
Follow-up to commit e27f4a942a ("bpf: Use mount_nodev not mount_ns
to mount the bpf filesystem"), which removes the FS_USERNS_MOUNT flag.
The original idea was to have a per mountns instance instead of a
single global fs instance, but that didn't work out and we had to
switch to mount_nodev() model. The intent of that middle ground was
that we avoid users who don't play nice to create endless instances
of bpf fs which are difficult to control and discover from an admin
point of view, but at the same time it would have allowed us to be
more flexible with regard to namespaces.
Therefore, since we now did the switch to mount_nodev() as a fix
where individual instances are created, we also need to remove userns
mount flag along with it to avoid running into mentioned situation.
I don't expect any breakage at this early point in time with removing
the flag and we can revisit this later should the requirement for
this come up with future users. This and commit e27f4a942a have
been split to facilitate tracking should any of them run into the
unlikely case of causing a regression.
Fixes: b2197755b2 ("bpf: add support for persistent maps/progs")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 049bbf589e ]
Commit fa50d974d1 ("ipv4: Namespaceify ip_default_ttl sysctl knob")
moves the default TTL assignment, and as side-effect IPv4 TTL now
has a default value only if sysctl support is enabled (CONFIG_SYSCTL=y).
The sysctl_ip_default_ttl is fundamental for IP to work properly,
as it provides the TTL to be used as default. The defautl TTL may be
used in ip_selected_ttl, through the following flow:
ip_select_ttl
ip4_dst_hoplimit
net->ipv4.sysctl_ip_default_ttl
This commit fixes the issue by assigning net->ipv4.sysctl_ip_default_ttl
in net_init_net, called during ipv4's initialization.
Without this commit, a kernel built without sysctl support will send
all IP packets with zero TTL (unless a TTL is explicitly set, e.g.
with setsockopt).
Given a similar issue might appear on the other knobs that were
namespaceify, this commit also moves them.
Fixes: fa50d974d1 ("ipv4: Namespaceify ip_default_ttl sysctl knob")
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e5aed006be ]
In case we find a socket with encapsulation enabled we should call
the encap_recv function even if just a udp header without payload is
available. The callbacks are responsible for correctly verifying and
dropping the packets.
Also, in case the header validation fails for geneve and vxlan we
shouldn't put the skb back into the socket queue, no one will pick
them up there. Instead we can simply discard them in the respective
encap_recv functions.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e27f4a942a ]
While reviewing the filesystems that set FS_USERNS_MOUNT I spotted the
bpf filesystem. Looking at the code I saw a broken usage of mount_ns
with current->nsproxy->mnt_ns. As the code does not acquire a
reference to the mount namespace it can not possibly be correct to
store the mount namespace on the superblock as it does.
Replace mount_ns with mount_nodev so that each mount of the bpf
filesystem returns a distinct instance, and the code is not buggy.
In discussion with Hannes Frederic Sowa it was reported that the use
of mount_ns was an attempt to have one bpf instance per mount
namespace, in an attempt to keep resources that pin resources from
hiding. That intent simply does not work, the vfs is not built to
allow that kind of behavior. Which means that the bpf filesystem
really is buggy both semantically and in it's implemenation as it does
not nor can it implement the original intent.
This change is userspace visible, but my experience with similar
filesystems leads me to believe nothing will break with a model of each
mount of the bpf filesystem is distinct from all others.
Fixes: b2197755b2 ("bpf: add support for persistent maps/progs")
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit addf8fc4ac ]
We used to check dev->reg_state against NETREG_REGISTERED after each
time we are woke up. But after commit 9e641bdcfa ("net-tun:
restructure tun_do_read for better sleep/wakeup efficiency"), it uses
skb_recv_datagram() which does not check dev->reg_state. This will
result if we delete a tun/tap device after a process is blocked in the
reading. The device will wait for the reference count which was held
by that process for ever.
Fixes this by using RCV_SHUTDOWN which will be checked during
sk_recv_datagram() before trying to wake up the process during uninit.
Fixes: 9e641bdcfa ("net-tun: restructure tun_do_read for better
sleep/wakeup efficiency")
Cc: Eric Dumazet <edumazet@google.com>
Cc: Xi Wang <xii@google.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1968a0b8b6 ]
In my last commit I replaced MACSEC_SA_ATTR_KEYID by
MACSEC_SA_ATTR_KEY.
Fixes: 8acca6aceb ("macsec: key identifier is 128 bits, not 64")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit da4ed55165 ]
The problem is that fib_info->nh is [0] so the struct fib_info
allocation size depends on number of nexthops. If we just copy fib_info,
we do not copy the nexthops info and driver accesses memory which is not
ours.
Given the fact that fib4 does not defer operations and therefore it does
not need copy, just pass the pointer down to drivers as it was done
before.
Fixes: 850d0cbc91 ("switchdev: remove pointers from switchdev objects")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 92964c79b3 ]
When we free cb->skb after a dump, we do it after releasing the
lock. This means that a new dump could have started in the time
being and we'll end up freeing their skb instead of ours.
This patch saves the skb and module before we unlock so we free
the right memory.
Fixes: 16b304f340 ("netlink: Eliminate kmalloc in netlink dump operation.")
Reported-by: Baozeng Ding <sploving1@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 45e093ae28 ]
Make sure the socket for which the user is listing publication exists
before parsing the socket netlink attributes.
Prior to this patch a call without any socket caused a NULL pointer
dereference in tipc_nl_publ_dump().
Tested-and-reported-by: Baozeng Ding <sploving1@gmail.com>
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.cm>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a621bac304 upstream.
When SCSI was written, all commands coming from the filesystem
(REQ_TYPE_FS commands) had data. This meant that our signal for needing
to complete the command was the number of bytes completed being equal to
the number of bytes in the request. Unfortunately, with the advent of
flush barriers, we can now get zero length REQ_TYPE_FS commands, which
confuse this logic because they satisfy the condition every time. This
means they never get retried even for retryable conditions, like UNIT
ATTENTION because we complete them early assuming they're done. Fix
this by special casing the early completion condition to recognise zero
length commands with errors and let them drop through to the retry code.
Reported-by: Sebastian Parschauer <s.parschauer@gmx.de>
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
Tested-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a215137423 upstream.
Commit 5e3ca2b349 ("regulator: Try to resolve regulators supplies on
registration") added a call to regulator_resolve_supply() within
regulator_register() where the regulator_list_mutex is held. This causes
a deadlock to occur on the Tegra114 Dalmore board when the palmas PMIC
is registered because regulator_register_resolve_supply() calls
regulator_dev_lookup() which may try to acquire the regulator_list_mutex
again.
Fix this by releasing the mutex before calling
regulator_register_resolve_supply() and update the error exit path to
ensure the mutex is released on an error.
[Made commit message more legible -- broonie]
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6979cd54c0 upstream.
A recent cleanup removed the only user of the 'kms' variable in
msm_preclose(), causing a harmless compiler warning:
drivers/gpu/drm/msm/msm_drv.c: In function 'msm_preclose':
drivers/gpu/drm/msm/msm_drv.c:468:18: error: unused variable 'kms' [-Werror=unused-variable]
This removes the variable as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 4016260ba4 ("drm/msm: fix bug after preclose removal")
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 51b07f30a7 upstream.
Some careless idiot(*) wrote crap code in commit 1a3e8f3 ("xfs:
convert inode cache lookups to use RCU locking") back in late 2010,
and so xfs_iflush_cluster checks the wrong inode for whether it is
still valid under RCU protection. Fix it to lock and check the
correct inode.
(*) Careless-idiot: Dave Chinner <dchinner@redhat.com>
Discovered-by: Brain Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b1438f4779 upstream.
When a failure due to an inode buffer occurs, the error handling
fails to abort the inode writeback correctly. This can result in the
inode being reclaimed whilst still in the AIL, leading to
use-after-free situations as well as filesystems that cannot be
unmounted as the inode log items left in the AIL never get removed.
Fix this by ensuring fatal errors from xfs_imap_to_bp() result in
the inode flush being aborted correctly.
Reported-by: Shyam Kaushik <shyam@zadarastorage.com>
Diagnosed-by: Shyam Kaushik <shyam@zadarastorage.com>
Tested-by: Shyam Kaushik <shyam@zadarastorage.com>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8179c03629 upstream.
Joe Lawrence reported a list_add corruption with 4.6-rc1 when
testing some custom md administration code that made it's own
block device nodes for the md array. The simple test loop of:
for i in {0..100}; do
mknod --mode=0600 $tmp/tmp_node b $MAJOR $MINOR
mdadm --detail --export $tmp/tmp_node > /dev/null
rm -f $tmp/tmp_node
done
Would produce this warning in bd_acquire() when mdadm opened the
device node:
list_add double add: new=ffff88043831c7b8, prev=ffff8804380287d8, next=ffff88043831c7b8.
And then produce this from bd_forget from kdevtmpfs evicting a block
dev inode:
list_del corruption. prev->next should be ffff8800bb83eb10, but was ffff88043831c7b8
This is a regression caused by commit c19b3b05 ("xfs: mode di_mode
to vfs inode"). The issue is that xfs_inactive() frees the
unlinked inode, and the above commit meant that this freeing zeroed
the mode in the struct inode. The problem is that after evict() has
called ->evict_inode, it expects the i_mode to be intact so that it
can call bd_forget() or cd_forget() to drop the reference to the
block device inode attached to the XFS inode.
In reality, the only thing we do in xfs_fs_evict_inode() that is not
generic is call xfs_inactive(). We can move the xfs_inactive() call
to xfs_fs_destroy_inode() without any problems at all, and this
will leave the VFS inode intact until it is completely done with it.
So, remove xfs_fs_evict_inode(), and do the work it used to do in
->destroy_inode instead.
Reported-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ad747e3b29 upstream.
Commit 96f859d ("libxfs: pack the agfl header structure so
XFS_AGFL_SIZE is correct") allowed the freelist to use the empty
slot at the end of the freelist on 64 bit systems that was not
being used due to sizeof() rounding up the structure size.
This has caused versions of xfs_repair prior to 4.5.0 (which also
has the fix) to report this as a corruption once the filesystem has
been grown. Older kernels can also have problems (seen from a whacky
container/vm management environment) mounting filesystems grown on a
system with a newer kernel than the vm/container it is deployed on.
To avoid this problem, change the initial free list indexes not to
wrap across the end of the AGFL, hence avoiding the initialisation
of agf_fllast to the last index in the AGFL.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0a58e8339 upstream.
Today, a kernel which refuses to mount a filesystem read-write
due to unknown ro-compat features can still transition to read-write
via the remount path. The old kernel is most likely none the wiser,
because it's unaware of the new feature, and isn't using it. However,
writing to the filesystem may well corrupt metadata related to that
new feature, and moving to a newer kernel which understand the feature
will have problems.
Right now the only ro-compat feature we have is the free inode btree,
which showed up in v3.16. It would be good to push this back to
all the active stable kernels, I think, so that if anyone is using
newer mkfs (which enables the finobt feature) with older kernel
releases, they'll be protected.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Bill O'Donnell <billodo@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c87bf43144 upstream.
Enabling CONFIG_GCOV_PROFILE_ALL produces us a lot of warnings like
lib/lz4/lz4hc_compress.c: In function 'lz4_compresshcctx':
lib/lz4/lz4hc_compress.c:514:1: warning: the frame size of 1504 bytes is larger than 1024 bytes [-Wframe-larger-than=]
After some investigation, I found that this behavior started with gcc-4.9,
and opened https://gcc.gnu.org/bugzilla/show_bug.cgi?id=69702.
A suggested workaround for it is to use the -fno-tree-loop-im
flag that turns off one of the optimization stages in gcc, so the
code runs a little slower but does not use excessive amounts
of stack.
We could make this conditional on the gcc version, but I could not
find an easy way to do this in Kbuild and the benefit would be
fairly small, given that most of the gcc version in production are
affected now.
I'm marking this for 'stable' backports because it addresses a bug
with code generation in gcc that exists in all kernel versions
with the affected gcc releases.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Michal Marek <mmarek@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 65a9f31c50 upstream.
After commit 21a59991ce ("scripts/package/Makefile: rpmbuild is needed
for rpm targets"), it is no longer possible to specify RPMOPTS.
For example, we can no longer able to control _topdir using the following
make command.
make RPMOPTS="--define '_topdir /home/xyz/workspace/'" binrpm-pkg
Fixes: 21a59991ce ("scripts/package/Makefile: rpmbuild is needed for rpm targets")
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Michal Marek <mmarek@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a17fb329d upstream.
Grygorii Strashko reports:
The PM runtime will be left disabled for the device if its
.suspend_late() callback fails and async suspend is not allowed
for this device. In this case device will not be added in
dpm_late_early_list and dpm_resume_early() will ignore this
device, as result PM runtime will be disabled for it forever
(side effect: after 8 subsequent failures for the same device
the PM runtime will be reenabled due to disable_depth overflow).
To fix this problem, add devices to dpm_late_early_list regardless
of whether or not device_suspend_late() returns errors for them.
That will ensure failures in there to be handled consistently for
all devices regardless of their async suspend/resume status.
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 935244cd54 upstream.
Currently, in ext4_mb_init(), there's a loop like the following:
do {
...
offset += 1 << (sb->s_blocksize_bits - i);
i++;
} while (i <= sb->s_blocksize_bits + 1);
Note that the updated offset is used in the loop's next iteration only.
However, at the last iteration, that is at i == sb->s_blocksize_bits + 1,
the shift count becomes equal to (unsigned)-1 > 31 (c.f. C99 6.5.7(3))
and UBSAN reports
UBSAN: Undefined behaviour in fs/ext4/mballoc.c:2621:15
shift exponent 4294967295 is too large for 32-bit type 'int'
[...]
Call Trace:
[<ffffffff818c4d25>] dump_stack+0xbc/0x117
[<ffffffff818c4c69>] ? _atomic_dec_and_lock+0x169/0x169
[<ffffffff819411ab>] ubsan_epilogue+0xd/0x4e
[<ffffffff81941cac>] __ubsan_handle_shift_out_of_bounds+0x1fb/0x254
[<ffffffff81941ab1>] ? __ubsan_handle_load_invalid_value+0x158/0x158
[<ffffffff814b6dc1>] ? kmem_cache_alloc+0x101/0x390
[<ffffffff816fc13b>] ? ext4_mb_init+0x13b/0xfd0
[<ffffffff814293c7>] ? create_cache+0x57/0x1f0
[<ffffffff8142948a>] ? create_cache+0x11a/0x1f0
[<ffffffff821c2168>] ? mutex_lock+0x38/0x60
[<ffffffff821c23ab>] ? mutex_unlock+0x1b/0x50
[<ffffffff814c26ab>] ? put_online_mems+0x5b/0xc0
[<ffffffff81429677>] ? kmem_cache_create+0x117/0x2c0
[<ffffffff816fcc49>] ext4_mb_init+0xc49/0xfd0
[...]
Observe that the mentioned shift exponent, 4294967295, equals (unsigned)-1.
Unless compilers start to do some fancy transformations (which at least
GCC 6.0.0 doesn't currently do), the issue is of cosmetic nature only: the
such calculated value of offset is never used again.
Silence UBSAN by introducing another variable, offset_incr, holding the
next increment to apply to offset and adjust that one by right shifting it
by one position per loop iteration.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=114701
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=112161
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5cb316cdf upstream.
Currently, in mb_find_order_for_block(), there's a loop like the following:
while (order <= e4b->bd_blkbits + 1) {
...
bb += 1 << (e4b->bd_blkbits - order);
}
Note that the updated bb is used in the loop's next iteration only.
However, at the last iteration, that is at order == e4b->bd_blkbits + 1,
the shift count becomes negative (c.f. C99 6.5.7(3)) and UBSAN reports
UBSAN: Undefined behaviour in fs/ext4/mballoc.c:1281:11
shift exponent -1 is negative
[...]
Call Trace:
[<ffffffff818c4d35>] dump_stack+0xbc/0x117
[<ffffffff818c4c79>] ? _atomic_dec_and_lock+0x169/0x169
[<ffffffff819411bb>] ubsan_epilogue+0xd/0x4e
[<ffffffff81941cbc>] __ubsan_handle_shift_out_of_bounds+0x1fb/0x254
[<ffffffff81941ac1>] ? __ubsan_handle_load_invalid_value+0x158/0x158
[<ffffffff816e93a0>] ? ext4_mb_generate_from_pa+0x590/0x590
[<ffffffff816502c8>] ? ext4_read_block_bitmap_nowait+0x598/0xe80
[<ffffffff816e7b7e>] mb_find_order_for_block+0x1ce/0x240
[...]
Unless compilers start to do some fancy transformations (which at least
GCC 6.0.0 doesn't currently do), the issue is of cosmetic nature only: the
such calculated value of bb is never used again.
Silence UBSAN by introducing another variable, bb_incr, holding the next
increment to apply to bb and adjust that one by right shifting it by one
position per loop iteration.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=114701
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=112161
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff0bc08454 upstream.
A failed call to dqget() returns an ERR_PTR() and not null. Fix
the check in ext4_ioctl_setproject() to handle this correctly.
Fixes: 9b7365fc1c ("ext4: add FS_IOC_FSSETXATTR/FS_IOC_FSGETXATTR interface support")
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7827a7f6eb upstream.
Instead of just printing warning messages, if the orphan list is
corrupted, declare the file system is corrupted. If there are any
reserved inodes in the orphaned inode list, declare the file system
corrupted and stop right away to avoid doing more potential damage to
the file system.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c9eb13a910 upstream.
If the orphaned inode list contains inode #5, ext4_iget() returns a
bad inode (since the bootloader inode should never be referenced
directly). Because of the bad inode, we end up processing the inode
repeatedly and this hangs the machine.
This can be reproduced via:
mke2fs -t ext4 /tmp/foo.img 100
debugfs -w -R "ssv last_orphan 5" /tmp/foo.img
mount -o loop /tmp/foo.img /mnt
(But don't do this if you are using an unpatched kernel if you care
about the system staying functional. :-)
This bug was found by the port of American Fuzzy Lop into the kernel
to find file system problems[1]. (Since it *only* happens if inode #5
shows up on the orphan list --- 3, 7, 8, etc. won't do it, it's not
surprising that AFL needed two hours before it found it.)
[1] http://events.linuxfoundation.org/sites/events/files/slides/AFL%20filesystem%20fuzzing%2C%20Vault%202016_0.pdf
Reported by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 06bd3c36a7 upstream.
Huang has reported that in his powerfail testing he is seeing stale
block contents in some of recently allocated blocks although he mounts
ext4 in data=ordered mode. After some investigation I have found out
that indeed when delayed allocation is used, we don't add inode to
transaction's list of inodes needing flushing before commit. Originally
we were doing that but commit f3b59291a6 removed the logic with a
flawed argument that it is not needed.
The problem is that although for delayed allocated blocks we write their
contents immediately after allocating them, there is no guarantee that
the IO scheduler or device doesn't reorder things and thus transaction
allocating blocks and attaching them to inode can reach stable storage
before actual block contents. Actually whenever we attach freshly
allocated blocks to inode using a written extent, we should add inode to
transaction's ordered inode list to make sure we properly wait for block
contents to be written before committing the transaction. So that is
what we do in this patch. This also handles other cases where stale data
exposure was possible - like filling hole via mmap in
data=ordered,nodelalloc mode.
The only exception to the above rule are extending direct IO writes where
blkdev_direct_IO() waits for IO to complete before increasing i_size and
thus stale data exposure is not possible. For now we don't complicate
the code with optimizing this special case since the overhead is pretty
low. In case this is observed to be a performance problem we can always
handle it using a special flag to ext4_map_blocks().
Fixes: f3b59291a6
Reported-by: "HUANG Weller (CM/ESW12-CN)" <Weller.Huang@cn.bosch.com>
Tested-by: "HUANG Weller (CM/ESW12-CN)" <Weller.Huang@cn.bosch.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 310944d148 upstream.
The component master driver imx-drm-core matches component devices using
their of_node. Since commit 950b410dd1ab ("gpu: ipu-v3: Fix imx-ipuv3-crtc
module autoloading"), the imx-ipuv3-crtc dev->of_node is not set during
probing. Before that, of_node was set and caused an of: modalias to be
used instead of the platform: modalias, which broke module autoloading.
On the other hand, if dev->of_node is not set yet when the imx-ipuv3-crtc
probe function calls component_add, component matching in imx-drm-core
fails. While dev->of_node will be set once the next component tries to
bring up the component master, imx-drm-core component binding will never
succeed if one of the crtc devices is probed last.
Add of_node to the component platform data and match against the
pdata->of_node instead of dev->of_node in imx-drm-core to work around
this problem.
Fixes: 950b410dd1ab ("gpu: ipu-v3: Fix imx-ipuv3-crtc module autoloading")
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Lothar Waßmann <LW@KARO-electronics.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b3daa5ef52 upstream.
Add a helper which aids in the identification of DP dual mode
(aka. DP++) adaptors. There are several types of adaptors
specified: type 1 DVI, type 1 HDMI, type 2 DVI, type 2 HDMI
Type 1 adaptors have a max TMDS clock limit of 165MHz, type 2 adaptors
may go as high as 300MHz and they provide a register informing the
source device what the actual limit is. Supposedly also type 1 adaptors
may optionally implement this register. This TMDS clock limit is the
main reason why we need to identify these adaptors.
Type 1 adaptors provide access to their internal registers and the sink
DDC bus through I2C. Type 2 adaptors provide this access both via I2C
and I2C-over-AUX. A type 2 source device may choose to implement either
of these methods. If a source device implements the I2C-over-AUX
method, then the driver will obviously need specific support for such
adaptors since the port is driven like an HDMI port, but DDC
communication happes over the AUX channel.
This helper should be enough to identify the adaptor type (some
type 1 DVI adaptors may be a slight exception) and the maximum TMDS
clock limit. Another feature that may be available is control over
the TMDS output buffers on the adaptor, possibly allowing for some
power saving when the TMDS link is down.
Other user controllable features that may be available in the adaptors
are downstream i2c bus speed control when using i2c-over-aux, and
some control over the CEC pin. I chose not to provide any helper
functions for those since I have no use for them in i915 at this time.
The rest of the registers in the adaptor are mostly just information,
eg. IEEE OUI, hardware and firmware revision, etc.
v2: Pass adaptor type to helper functions to ease driver implementation
Fix a bunch of typoes (Paulo)
Add DRM_DP_DUAL_MODE_UNKNOWN for the case where we don't (yet) know
the type (Paulo)
Reject 0x00 and 0xff DP_DUAL_MODE_MAX_TMDS_CLOCK values (Paulo)
Adjust drm_dp_dual_mode_detect() type2 vs. type1 detection to
ease future LSPCON enabling
Remove the unused DP_DUAL_MODE_LAST_RESERVED define
v3: Fix kernel doc function argument descriptions (Jani)
s/NONE/UNKNOWN/ in drm_dp_dual_mode_detect() docs
Add kernel doc for enum drm_dp_dual_mode_type
Actually build the docs
Fix more typoes
v4: Adjust code indentation of type2 adaptor detection (Shashank)
Add debug messages for failurs cases (Shashank)
v5: EXPORT_SYMBOL(drm_dp_dual_mode_read) (Paulo)
Cc: Tore Anderson <tore@fud.no>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com> (v4)
Link: http://patchwork.freedesktop.org/patch/msgid/1462542412-25533-1-git-send-email-ville.syrjala@linux.intel.com
(cherry picked from commit ede53344db)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c578d15226 upstream.
Try to detect the max TMDS clock limit for the DP++ adaptor (if any)
and take it into account when checking the port clock.
Note that as with the sink (HDMI vs. DVI) TMDS clock limit we'll ignore
the adaptor TMDS clock limit in the modeset path, in case users are
already "overclocking" their TMDS links. One subtle change here is that
we'll have to respect the adaptor TMDS clock limit when we decide whether
to do 12bpc or 8bpc, otherwise we might end up picking 12bpc and
accidentally driving the TMDS link out of spec even when the user chose
a mode that fits wihting the limits at 8bpc. This means you can't
"overclock" your DP++ dongle at 12bpc anymore, but you can continue to
do so at 8bpc.
Note that for simplicity we'll use the I2C access method for all dual
mode adaptors including type 2. Otherwise we'd have to start mixing
DP AUX and HDMI together. In the future we may need to do that if we
come across any board designs that don't hook up the DDC pins to the
DP++ connectors. Such boards would obviously only work with type 2
dual mode adaptors, and not type 1.
v2: Store adaptor type under indel_hdmi->dp_dual_mode
Deal with DRM_DP_DUAL_MODE_UNKNOWN
Pass adaptor type to drm_dp_dual_mode_max_tmds_clock(),
and use it for type1 adaptors as well
Reported-by: Tore Anderson <tore@fud.no>
Fixes: 7a0baa6234 ("Revert "drm/i915: Disable 12bpc hdmi for now"")
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462216105-20881-3-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
(cherry picked from commit b1ba124d8e)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 55441070ca upstream.
The memcpy of ipv6 header destination address to the skb control block
(sbk->cb) in header_create() results in currupted memory when bt_xmit()
is issued. The skb->cb is "released" in the return of header_create()
making room for lower layer to minipulate the skb->cb.
The value retrieved in bt_xmit is not persistent across header creation
and sending, and the lower layer will overwrite portions of skb->cb,
making the copied destination address wrong.
The memory corruption will lead to non-working multicast as the first 4
bytes of the copied destination address is replaced by a value that
resolves into a non-multicast prefix.
This fix removes the dependency on the skb control block between header
creation and send, by moving the destination address memcpy to the send
function path (setup_create, which is called from bt_xmit).
Signed-off-by: Glenn Ruben Bakke <glenn.ruben.bakke@nordicsemi.no>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unfortunately since we don't have Dave's connector refcounting patch
here yet, it's very possible that drm_atomic_state_default_clear() could
get called by intel_display_resume() when
intel_dp_mst_destroy_connector() isn't completely finished destroying an
mst connector, but has already finished setting connector->funcs to
NULL. As such, we need to treat the connector like it's already been
destroyed and just skip it, otherwise we'll end up dereferencing a NULL
pointer.
This fix is only required for 4.6 and below. David Airlie's patchseries
for 4.7 to add connector reference counting provides a more proper fix
for this.
Changes since v1:
- Fix leftover whitespace
Upstream fix: 0552f7651b ("drm/i915/mst: use reference counted
connectors. (v3)")
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Lyude <cpaul@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If an MST device is disconnected while the machine is suspended, the
number of connectors will change as well after we call
intel_dp_mst_resume(). This means that any previous atomic state we had
before suspending is no longer valid, since it'll still be pointing to
missing connectors. We need to check for this before committing the
state, otherwise we'll kernel panic on resume whenever if any MST
display was disconnected before we started resuming:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
IP: [<ffffffffa01588ef>] drm_atomic_helper_check_modeset+0x29f/0xb40 [drm_kms_helper]
Call Trace:
[<ffffffffa02354f4>] intel_atomic_check+0x34/0x1180 [i915]
[<ffffffff810e6c3f>] ? mark_held_locks+0x6f/0xa0
[<ffffffff810e6d99>] ? trace_hardirqs_on_caller+0x129/0x1b0
[<ffffffffa00ff1d2>] drm_atomic_check_only+0x192/0x620 [drm]
[<ffffffff813ee001>] ? pci_pm_thaw+0x21/0x90
[<ffffffffa00ff677>] drm_atomic_commit+0x17/0x60 [drm]
[<ffffffffa023e0ad>] intel_display_resume+0xbd/0x160 [i915]
[<ffffffff813ee070>] ? pci_pm_thaw+0x90/0x90
[<ffffffffa01b60d8>] i915_drm_resume+0xd8/0x160 [i915]
[<ffffffffa01b6185>] i915_pm_resume+0x25/0x30 [i915]
[<ffffffff813ee0d4>] pci_pm_resume+0x64/0xa0
[<ffffffff814d9ea0>] dpm_run_callback+0x90/0x190
[<ffffffff814da455>] device_resume+0xd5/0x1f0
[<ffffffff814da58d>] async_resume+0x1d/0x50
[<ffffffff810b6718>] async_run_entry_fn+0x48/0x150
[<ffffffff810acc19>] process_one_work+0x1e9/0x5c0
[<ffffffff810acb96>] ? process_one_work+0x166/0x5c0
[<ffffffff810ad038>] worker_thread+0x48/0x4e0
[<ffffffff810acff0>] ? process_one_work+0x5c0/0x5c0
[<ffffffff810b3794>] kthread+0xe4/0x100
[<ffffffff81742672>] ret_from_fork+0x22/0x50
[<ffffffff810b36b0>] ? kthread_create_on_node+0x200/0x200
Changes since v1:
- Move drm_atomic_state_free() call down so we're holding the
appropriate locks when destroying the atomic state
Changes since v2:
- Check that state != NULL before we start accessing it's members
This fix is only required for 4.6 and below. David Airlie's patchseries
for 4.7 to add connector reference counting provides a more proper fix
for this.
Upstream fix: 0552f7651b ("drm/i915/mst: use reference counted
connectors. (v3)")
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Lyude <cpaul@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 255f0e7c41 upstream.
During boot, MST hotplugs are generally expected (even if no physical
hotplugging occurs) and result in DRM's connector topology changing.
This means that using num_connector from the current mode configuration
can lead to the number of connectors changing under us. This can lead to
some nasty scenarios in fbcon:
- We allocate an array to the size of dev->mode_config.num_connectors.
- MST hotplug occurs, dev->mode_config.num_connectors gets incremented.
- We try to loop through each element in the array using the new value
of dev->mode_config.num_connectors, and end up going out of bounds
since dev->mode_config.num_connectors is now larger then the array we
allocated.
fb_helper->connector_count however, will always remain consistent while
we do a modeset in fb_helper.
Note: This is just polish for 4.7, Dave Airlie's drm_connector
refcounting fixed these bugs for real. But it's good enough duct-tape
for stable kernel backporting, since backporting the refcounting
changes is way too invasive.
Signed-off-by: Lyude <cpaul@redhat.com>
[danvet: Clarify why we need this. Also remove the now unused "dev"
local variable to appease gcc.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1463065021-18280-3-git-send-email-cpaul@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 14a3842a1d upstream.
During boot time, MST devices usually send a ton of hotplug events
irregardless of whether or not any physical hotplugs actually occurred.
Hotplugs mean connectors being created/destroyed, and the number of DRM
connectors changing under us. This isn't a problem if we use
fb_helper->connector_count since we only set it once in the code,
however if we use num_connector from struct drm_mode_config we risk it's
value changing under us. On top of that, there's even a chance that
dev->mode_config.num_connector != fb_helper->connector_count. If the
number of connectors happens to increase under us, we'll end up using
the wrong array size for memcpy and start writing beyond the actual
length of the array, occasionally resulting in kernel panics.
Note: This is just polish for 4.7, Dave Airlie's drm_connector
refcounting fixed these bugs for real. But it's good enough duct-tape
for stable kernel backporting, since backporting the refcounting
changes is way too invasive.
Signed-off-by: Lyude <cpaul@redhat.com>
[danvet: Clarify why we need this.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1463065021-18280-2-git-send-email-cpaul@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9d746ab681 upstream.
When porting the hdmi deep color detection code from
radeon-kms to amdgpu-kms apparently some kind of
copy and paste error happened, attaching an else
branch to the wrong if statement.
The result is that hdmi deep color mode is always
disabled, regardless of gpu and display capabilities and
user wishes, as the code mistakenly thinks that the display
doesn't provide the required max_tmds_clock limit and falls
back to 8 bpc.
This patch fixes deep color support, as tested on a
R9 380 Tonga Pro + suitable display, and should be
backported to all kernels with amdgpu-kms support.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 93cd16817a upstream.
Some global KMS state that is elsewhere protected by the mode_config
mutex here needs to be protected with a local mutex. Remove corresponding
lockdep checks and introduce a new driver-private global_kms_state_mutex,
and make sure its locking order is *after* the crtc locks in order to
avoid having to release those when the new mutex is taken.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ccca1d5bf upstream.
Fix possible out of bounds read, by adding missing comma.
The code may read pass the end of the dsi_errors array
when the most significant bit (bit #31) in the intr_stat register
is set.
This bug has been detected using CppCheck (static analysis tool).
Signed-off-by: Itai Handler <itai_handler@hotmail.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c0cb8bf3a8 upstream.
The length of the GSS MIC token need not be a multiple of four bytes.
It is then padded by XDR to a multiple of 4 B, but unwrap_integ_data()
would previously only trim mic.len + 4 B. The remaining up to three
bytes would then trigger a check in nfs4svc_decode_compoundargs(),
leading to a "garbage args" error and mount failure:
nfs4svc_decode_compoundargs: compound not properly padded!
nfsd: failed to decode arguments!
This would prevent older clients using the pre-RFC 4121 MIC format
(37-byte MIC including a 9-byte OID) from mounting exports from v3.9+
servers using krb5i.
The trimming was introduced by commit 4c190e2f91 ("sunrpc: trim off
trailing checksum before returning decrypted or integrity authenticated
buffer").
Fixes: 4c190e2f91 "unrpc: trim off trailing checksum..."
Signed-off-by: Tomáš Trnka <ttrnka@mail.muni.cz>
Acked-by: Jeff Layton <jlayton@poochiereds.net>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd14be92fb upstream.
Instead of having two functions for cycling through the E820 map in
order to count to be remapped pages and remap them later, just use one
function with a caller supplied sub-function called for each region to
be processed. This eliminates the possibility of a mismatch between
both loops which showed up in certain configurations.
Suggested-by: Ed Swierk <eswierk@skyportsystems.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5a0cdbfd17 upstream.
The function eeh_pe_reset_and_recover() is used to recover EEH
error when the passthrou device are transferred to guest and
backwards. The content in the device's config space will be lost
on PE reset issued in the middle of the recovery. The function
saves/restores it before/after the reset. However, config access
to some adapters like Broadcom BCM5719 at this point will causes
fenced PHB. The config space is always blocked and we save 0xFF's
that are restored at late point. The memory BARs are totally
corrupted, causing another EEH error upon access to one of the
memory BARs.
This restores the config space on those adapters like BCM5719
from the content saved to the EEH device when it's populated,
to resolve above issue.
Fixes: 5cfb20b9 ("powerpc/eeh: Emulate EEH recovery for VFIO devices")
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2078d9ef6 upstream.
This reverts commit 89a51df5ab.
The function eeh_add_device_early() is used to perform EEH
initialization in devices added later on the system, like in
hotplug/DLPAR scenarios. Since the commit 89a51df5ab ("powerpc/eeh:
Fix crash in eeh_add_device_early() on Cell") a new check was introduced
in this function - Cell has no EEH capabilities which led to kernel oops
if hotplug was performed, so checking for eeh_enabled() was introduced
to avoid the issue.
However, in architectures that EEH is present like pSeries or PowerNV,
we might reach a case in which no PCI devices are present on boot time
and so EEH is not initialized. Then, if a device is added via DLPAR for
example, eeh_add_device_early() fails because eeh_enabled() is false,
and EEH end up not being enabled at all.
This reverts the aforementioned patch since a new verification was
introduced by the commit d91dafc02f ("powerpc/eeh: Delay probing EEH
device during hotplug") and so the original Cell issue does not happen
anymore.
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit affeb0f2d3 upstream.
The function eeh_pe_reset_and_recover() is used to recover EEH
error when the passthrough device are transferred to guest and
backwards, meaning the device's driver is vfio-pci or none.
When the driver is vfio-pci that provides error_detected() error
handler only, the handler simply stops the guest and it's not
expected behaviour. On the other hand, no error handlers will
be called if we don't have a bound driver.
This ignores the error handler in eeh_pe_reset_and_recover()
that reports the error to device driver to avoid the exceptional
behaviour.
Fixes: 5cfb20b9 ("powerpc/eeh: Emulate EEH recovery for VFIO devices")
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ed8ab4004 upstream.
Some of the interrupt vectors on 64-bit POWER server processors are only
32 bytes long (8 instructions), which is not enough for the full
first-level interrupt handler. For these we need to branch to an
out-of-line (OOL) handler. But when we are running a relocatable kernel,
interrupt vectors till __end_interrupts marker are copied down to real
address 0x100. So, branching to labels (ie. OOL handlers) outside this
section must be handled differently (see LOAD_HANDLER()), considering
relocatable kernel, which would need at least 4 instructions.
However, branching from interrupt vector means that we corrupt the
CFAR (come-from address register) on POWER7 and later processors as
mentioned in commit 1707dd16. So, EXCEPTION_PROLOG_0 (6 instructions)
that contains the part up to the point where the CFAR is saved in the
PACA should be part of the short interrupt vectors before we branch out
to OOL handlers.
But as mentioned already, there are interrupt vectors on 64-bit POWER
server processors that are only 32 bytes long (like vectors 0x4f00,
0x4f20, etc.), which cannot accomodate the above two cases at the same
time owing to space constraint. Currently, in these interrupt vectors,
we simply branch out to OOL handlers, without using LOAD_HANDLER(),
which leaves us vulnerable when running a relocatable kernel (eg. kdump
case). While this has been the case for sometime now and kdump is used
widely, we were fortunate not to see any problems so far, for three
reasons:
1. In almost all cases, production kernel (relocatable) is used for
kdump as well, which would mean that crashed kernel's OOL handler
would be at the same place where we end up branching to, from short
interrupt vector of kdump kernel.
2. Also, OOL handler was unlikely the reason for crash in almost all
the kdump scenarios, which meant we had a sane OOL handler from
crashed kernel that we branched to.
3. On most 64-bit POWER server processors, page size is large enough
that marking interrupt vector code as executable (see commit
429d2e83) leads to marking OOL handler code from crashed kernel,
that sits right below interrupt vector code from kdump kernel, as
executable as well.
Let us fix this by moving the __end_interrupts marker down past OOL
handlers to make sure that we also copy OOL handlers to real address
0x100 when running a relocatable kernel.
This fix has been tested successfully in kdump scenario, on an LPAR with
4K page size by using different default/production kernel and kdump
kernel.
Also tested by manually corrupting the OOL handlers in the first kernel
and then kdump'ing, and then causing the OOL handlers to fire - mpe.
Fixes: c1fb6816fb ("powerpc: Add relocation on exception vector handlers")
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The router is put down twice when it was non-NULL and either orig_ifinfo is
NULL afterwards or batman-adv receives a packet with the same sequence
number. This will end up in a use-after-free when the batadv_neigh_node is
removed because the reference counter ended up too early at 0.
This patch is skipping netdev and is being sent directly to stable in
accordance with David S. Miller[1].
The reason is that this patch applies only on linux-4.6 and not on
linux-4.7/net because it was "accidentally" fixed by a refactoring
commit (more details in [2]).
It addresses a reference imbalance which systematically leads to a
use-after-free and then a kernel crash.
[1] https://www.mail-archive.com/b.a.t.m.a.n@lists.open-mesh.org/msg15258.html
[2] https://www.mail-archive.com/b.a.t.m.a.n@lists.open-mesh.org/msg15252.html
Fixes: 9323158ef9 ("batman-adv: OGMv2 - implement originators logic")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 11ca2b7ab4 upstream.
New bindings use "fsl,t1040-ucc-uart" as the compatible for qe-uart.
So add it.
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf959931dd upstream.
The following program (simplified version of generated by syzkaller)
#include <pthread.h>
#include <unistd.h>
#include <sys/ptrace.h>
#include <stdio.h>
#include <signal.h>
void *thread_func(void *arg)
{
ptrace(PTRACE_TRACEME, 0,0,0);
return 0;
}
int main(void)
{
pthread_t thread;
if (fork())
return 0;
while (getppid() != 1)
;
pthread_create(&thread, NULL, thread_func, NULL);
pthread_join(thread, NULL);
return 0;
}
creates an unreapable zombie if /sbin/init doesn't use __WALL.
This is not a kernel bug, at least in a sense that everything works as
expected: debugger should reap a traced sub-thread before it can reap the
leader, but without __WALL/__WCLONE do_wait() ignores sub-threads.
Unfortunately, it seems that /sbin/init in most (all?) distributions
doesn't use it and we have to change the kernel to avoid the problem.
Note also that most init's use sys_waitid() which doesn't allow __WALL, so
the necessary user-space fix is not that trivial.
This patch just adds the "ptrace" check into eligible_child(). To some
degree this matches the "tsk->ptrace" in exit_notify(), ->exit_signal is
mostly ignored when the tracee reports to debugger. Or WSTOPPED, the
tracer doesn't need to set this flag to wait for the stopped tracee.
This obviously means the user-visible change: __WCLONE and __WALL no
longer have any meaning for debugger. And I can only hope that this won't
break something, but at least strace/gdb won't suffer.
We could make a more conservative change. Say, we can take __WCLONE into
account, or !thread_group_leader(). But it would be nice to not
complicate these historical/confusing checks.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Jan Kratochvil <jan.kratochvil@redhat.com>
Cc: "Michael Kerrisk (man-pages)" <mtk.manpages@gmail.com>
Cc: Pedro Alves <palves@redhat.com>
Cc: Roland McGrath <roland@hack.frob.com>
Cc: <syzkaller@googlegroups.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4b50bcc7ed upstream.
Since commit 92923ca3aa ("mm: meminit: only set page reserved in the
memblock region") the reserved bit is set on reserved memblock regions.
However start and end address are passed as unsigned long. This is only
32bit on i386, so it can end up marking the wrong pages reserved for
ranges at 4GB and above.
This was observed on a 32bit Xen dom0 which was booted with initial
memory set to a value below 4G but allowing to balloon in memory
(dom0_mem=1024M for example). This would define a reserved bootmem
region for the additional memory (for example on a 8GB system there was
a reverved region covering the 4GB-8GB range). But since the addresses
were passed on as unsigned long, this was actually marking all pages
from 0 to 4GB as reserved.
Fixes: 92923ca3aa ("mm: meminit: only set page reserved in the memblock region")
Link: http://lkml.kernel.org/r/1463491221-10573-1-git-send-email-stefan.bader@canonical.com
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 06af9b0f49 upstream.
The OID_sha224 case is missing a break and it falls through
to the -ENOPKG error default. Since HASH_ALGO_SHA224 seems
to be supported, this looks like an unintentional missing break.
Fixes: 07f081fb50 ("PKCS#7: Add OIDs for sha224, sha284 and sha512 hash algos and use them")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit baf43c6eac upstream.
In v4l2-compliance utility, test VIDIOC_CREATE_BUFS will check whether reserved
filed of v4l2_create_buffers filled with zero
Reserved field is filled with zero in v4l_create_bufs.
This patch copy reserved field of v4l2_create_buffer from kernel space to user
space
Signed-off-by: Tiffany Lin <tiffany.lin@mediatek.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ad67b437f1 upstream.
b84106b4e2 ("PCI: Disable IO/MEM decoding for devices with non-compliant
BARs") disabled BAR sizing for BARs 0-5 of devices that don't comply with
the PCI spec. But it didn't do anything for expansion ROM BARs, so we
still try to size them, resulting in warnings like this on Broadwell-EP:
pci 0000:ff:12.0: BAR 6: failed to assign [mem size 0x00000001 pref]
Move the non-compliant BAR check from __pci_read_base() up to
pci_read_bases() so it applies to the expansion ROM BAR as well as
to BARs 0-5.
Note that direct callers of __pci_read_base(), like sriov_init(), will now
bypass this check. We haven't had reports of devices with broken SR-IOV
BARs yet.
[bhelgaas: changelog]
Fixes: b84106b4e2 ("PCI: Disable IO/MEM decoding for devices with non-compliant BARs")
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Ingo Molnar <mingo@redhat.com>
CC: "H. Peter Anvin" <hpa@zytor.com>
CC: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 71324fdc72 upstream.
The range is registered into a linked list which can be referenced
throughout the lifetime of the driver. Ensure the range's memory is useful
for the same lifetime by adding it to the driver's private data structure.
The bug was introduced in the driver's initial commit, which was present in
v3.10.
Fixes: f0b9a7e521 ("pinctrl: exynos5440: add pinctrl driver for Samsung EXYNOS5440 SoC")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 959ca92a32 upstream.
The current driver calculates the clock divider with
fractional support enabled.
But it does not enable fractional support in the
control register itself resulting in an integer only divider,
but in clk_set_rate responds back the fractionally divided
clock frequency.
This patch enables fractional support in the control register
whenever there is a fractional bit set in the requested clock divider.
Mash clock limits are are also handled for the PWM clock
applying the correct divider limits (2 and max_int) applicable to
basic fractional divider support (mash order of 1).
It also adds locking to protect the read/modify/write cycle of
the register modification.
Fixes: 41691b8862 ("clk: bcm2835: Add support for programming the
audio domain clocks")
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 997f16bd5d upstream.
Current clamping of a normal divider allows a value < 1 to be valid.
A divider of < 1 would actually only be possible if we had a PLL...
So this patch clamps the divider to 1.
Fixes: 41691b8862 ("clk: bcm2835: Add support for programming the
audio domain clocks")
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6727f086cf upstream.
bcm2835_pll_off is currently assigning CM_PLL_ANARST to the control
register, which may lose the other bits that are currently set by the
clock dividers.
It also now locks during the read/modify/write cycle of both
registers.
Fixes: 41691b8862 ("clk: bcm2835: Add support for programming the
audio domain clocks")
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e708b383f4 upstream.
In poweroff, we set the reset bit and the power down bit, but only
managed to unset the reset bit for poweron. This meant that if HDMI
did -EPROBE_DEFER after it had grabbed its clocks, we'd power down the
PLLH (that had been on at boot time) and never recover.
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes: 41691b8862 ("clk: bcm2835: Add support for programming the audio domain clocks")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7387da520 upstream.
Commit 0b89e9aa28 (cpuidle: delay enabling interrupts until all
coupled CPUs leave idle) rightfully fixed a regression by letting
the coupled idle state framework to handle local interrupt enabling
when the CPU is exiting an idle state.
The current code checks if the idle state is coupled and, if so, it
will let the coupled code to enable interrupts. This way, it can
decrement the ready-count before handling the interrupt. This
mechanism prevents the other CPUs from waiting for a CPU which is
handling interrupts.
But the check is done against the state index returned by the back
end driver's ->enter functions which could be different from the
initial index passed as parameter to the cpuidle_enter_state()
function.
entered_state = target_state->enter(dev, drv, index);
[ ... ]
if (!cpuidle_state_is_coupled(drv, entered_state))
local_irq_enable();
[ ... ]
If the 'index' is referring to a coupled idle state but the
'entered_state' is *not* coupled, then the interrupts are enabled
again. All CPUs blocked on the sync barrier may busy loop longer
if the CPU has interrupts to handle before decrementing the
ready-count. That's consuming more energy than saving.
Fixes: 0b89e9aa28 (cpuidle: delay enabling interrupts until all coupled CPUs leave idle)
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
[ rjw: Subject & changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c998c07836 upstream.
Currently the 'registered' member of the cpuidle_device struct is set
to 1 during cpuidle_register_device. In this same function there are
checks to see if the device is already registered to prevent duplicate
calls to register the device, but this value is never set to 0 even on
unregister of the device. Because of this, any attempt to call
cpuidle_register_device after a call to cpuidle_unregister_device will
fail which shouldn't be the case.
To prevent this, set registered to 0 when the device is unregistered.
Fixes: c878a52d3c (cpuidle: Check if device is already registered)
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0ae3aeefab upstream.
As pm_runtime_set_active() may fail because the device's parent isn't
active, we can end up executing the ->runtime_resume() callback for the
device when it isn't allowed.
Fix this by invoking pm_runtime_set_active() before running the callback
and let's also deal with the error code.
Fixes: 37f204164d (PM: Add pm_runtime_suspend|resume_force functions)
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 41a3da2b8e upstream.
All configurations are lost and the registers will have
default values when the hardware is suspended and resumed,
so saving the private register space context on suspend, and
restoring it on resume.
Fixes: 4b45efe852 (mfd: Add support for Intel Sunrisepoint LPSS devices)
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7f0c5ae18d upstream.
There is a potential resource leak in case when ->probe() fails. We have to
unregister and remove clock tree which is done here.
This is a follow up to previously pushed commit c4726abce6 ("mfd:
intel_quark_i2c_gpio: Use clkdev_create()") that prevents double free() when
clkdev_drop() followed by kfree() in devm_kcalloc() release stage.
I leave Fixes tag here, but the backporting will require to backport the commit
c4726abce6 ("mfd: intel_quark_i2c_gpio: Use clkdev_create()") first.
Fixes: 60ae5b9f5c (mfd: intel_quark_i2c_gpio: Add Intel Quark X1000 I2C-GPIO MFD Driver)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a18afe809 upstream.
On ads7828 the internal reference defaults to off upon power up. When
using internal reference, it needs to be turned on and the voltage needs
to settle before normal conversion cycle can be started. Hence perform a
dummy read in the probe to enable the internal reference allowing the
voltage to settle before performing a normal read.
Without this fix, the first read from the ADC when using internal
reference always returns incorrect data.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e3ca2b349 upstream.
Commit 6261b06de5 ("regulator: Defer lookup of supply to regulator_get")
moved the regulator supplies lookup logic from the regulators registration
to the regulators get time.
Unfortunately, that changed the behavior of the regulator core since now a
parent supply with a child regulator marked as always-on, won't be enabled
unless a client driver attempts to get the child regulator during boot.
This patch tries to resolve the parent supply for the already registered
regulators each time that a new regulator is registered. So the regulators
that have child regulators marked as always on will be enabled regardless
if a driver gets the child regulator or not.
That was the behavior before the mentioned commit, since parent supplies
were looked up at regulator registration time instead of during child get.
Since regulator_resolve_supply() checks for rdev->supply, most of the times
it will be a no-op. Errors aren't checked to keep the possible out of order
dependencies which was the motivation for the mentioned commit.
Also, the supply being available will be enforced on regulator get anyways
in case the resolve fails on regulators registration.
Fixes: 6261b06de5 ("regulator: Defer lookup of supply to regulator_get")
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 78cbccd3bd upstream.
When KDUMP is triggered the driver first talks to the firmware in INTX
mode, but the adapter firmware is still in MSIX mode. Therefore the first
driver command hangs since the driver is waiting for an INTX response and
firmware gives a MSIX response. If when the OS is installed on a RAID
drive created by the adapter KDUMP will hang since the driver does not
receive a response in sync mode.
Fixed by: Change the firmware to INTX mode if it is in MSIX mode before
sending the first sync command.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc4bf75ea3 upstream.
Typically under error conditions, it is possible for aac_command_thread()
to miss the wakeup from kthread_stop() and go back to sleep, causing it
to hang aac_shutdown.
In the observed scenario, the adapter is not functioning correctly and so
aac_fib_send() never completes (or time-outs depending on how it was
called). Shortly after aac_command_thread() starts it performs
aac_fib_send(SendHostTime) which hangs. When aac_probe_one
/aac_get_adapter_info send time outs, kthread_stop is called which breaks
the command thread out of it's hang.
The code will still go back to sleep in schedule_timeout() without
checking kthread_should_stop() so it causes aac_probe_one to hang until
the schedule_timeout() which is 30 minutes.
Fixed by: Adding another kthread_should_stop() before schedule_timeout()
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07beca2be2 upstream.
aac_fib_send has a special function case for initial commands during
driver initialization using wait < 0(pseudo sync mode). In this case,
the command does not sleep but rather spins checking for timeout.This
loop is calls cpu_relax() in an attempt to allow other processes/threads
to use the CPU, but this function does not relinquish the CPU and so the
command will hog the processor. This was observed in a KDUMP
"crashkernel" and that prevented the "command thread" (which is
responsible for completing the command from being timed out) from
starting because it could not get the CPU.
Fixed by replacing "cpu_relax()" call with "schedule()"
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 873ffe154a upstream.
In commit a269913c52 ("rtlwifi: Rework rtl_lps_leave() and
rtl_lps_enter() to use work queue"), the tests for enter/exit
power-save mode were inverted. With this change applied, the
wifi connection becomes much more stable.
Fixes: a269913c52 ("rtlwifi: Rework rtl_lps_leave() and rtl_lps_enter() to use work queue")
Signed-off-by: Wang YanQing <udknight@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit baa1702290 upstream.
The previous patch added an option to rtl8723be to manually select the
antenna for those cases when only a single antenna is present, and the
on-board EEPROM is incorrectly programmed. This patch implements the
necessary changes in the Bluetooth coexistence driver.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c18d8f5095 upstream.
A number of new laptops have been delivered with only a single antenna.
In principle, this is OK; however, a problem arises when the on-board
EEPROM is programmed to use the other antenna connection. The option
of opening the computer and moving the connector is not always possible
as it will void the warranty in some cases. In addition, this solution
breaks the Windows driver when the box dual boots Linux and Windows.
A fix involving a new module parameter has been developed. This commit
adds the new parameter and implements the changes needed for the driver.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f1925d78d7 upstream.
In case of timeout during read operation, the exit path lacked PM
runtime put. This could lead to unbalanced runtime PM usage counter thus
leaving the device in an active state.
Fixes: d7fd6075a2 ("hwrng: exynos - Add timeout for waiting on init done")
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b9bc799a4 upstream.
BugLink: http://bugs.launchpad.net/bugs/972604
Commit 09c9bae26b ("ath5k: add led pin
configuration for compaq c700 laptop") added a pin configuration for the Compaq
c700 laptop. However, the polarity of the led pin is reversed. It should be
red for wifi off and blue for wifi on, but it is the opposite. This bug was
reported in the following bug report:
http://pad.lv/972604
Fixes: 09c9bae26b ("ath5k: add led pin configuration for compaq c700 laptop")
Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4ad24a9d83 upstream.
It is observed that while loading and unloading ath10k modules
in an infinite loop, before ath10k_core_start() completion HTT
rx frames are received, while processing these frames,
dereferencing the arvifs list code is getting hit before
initilizing the arvifs list, causing a kernel panic.
This patch initilizes the arvifs list before initilizing htt.
Fixes the below issue:
[<bf88b058>] (ath10k_htt_rx_pktlog_completion_handler+0x278/0xd08 [ath10k_core])
[<bf88b058>] (ath10k_htt_rx_pktlog_completion_handler [ath10k_core])
[<bf88c0dc>] (ath10k_htt_txrx_compl_task+0x5f4/0xeb0 [ath10k_core])
[<bf88c0dc>] (ath10k_htt_txrx_compl_task [ath10k_core])
[<c0234100>] (tasklet_action+0x8c/0xec)
[<c0234100>] (tasklet_action)
[<c02337c0>] (__do_softirq+0xf8/0x228)
[<c02337c0>] (__do_softirq) [<c0233920>] (run_ksoftirqd+0x30/0x90)
Code: e5954ad8 e2899008 e1540009 0a00000d (e5943008)
---[ end trace 71de5c2e011dbf56 ]---
Kernel panic - not syncing: Fatal exception in interrupt
Fixes: 500ff9f938 ("ath10k: implement chanctx API")
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ce8c1484e upstream.
Upon firmware assert, restart work will be triggered so that mac80211
will reconfigure the driver. An issue is reported that after restart
work, survey dump data do not contain in-use (SURVEY_INFO_IN_USE) info
for operating channel. During reconfigure, since mac80211 already has
valid channel context for given radio, channel context iteration return
num_chanctx > 0. Hence rx_channel is always NULL. Fix this by assigning
channel context to rx_channel when driver restart is in progress.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a75fc5474 upstream.
commit 166de3f189 ("ath10k: remove supported chain mask") had revealed
an issue on monitor mode. Configuring NSS upon monitor interface
creation is causing target assert in all qca9888x and qca6174 firmware.
Firmware assert issue can be reproduced by below sequence even after
reverting commit 166de3f189 ("ath10k: remove supported chain mask").
ip link set wlan0 down
iw wlan0 set type monitor
iw phy0 set antenna 7
ip link set wlan0 up
This issue is originally reported on qca9888 with 10.1 firmware.
Fixes: 5572a95b4b ("ath10k: apply chainmask settings to vdev on creation")
Reported-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9ddc486aa0 upstream.
It is observed that, we are disabling the packet log if we write same
value to the pktlog_filter for the second time. Always enable pktlogs
on non zero filter.
Fixes: 90174455ae ("ath10k: add support to configure pktlog filter")
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3397c2c45b upstream.
A new element got inserted into enum mx35_clks with commit 3713e3f5e9
("clk: imx35: define two clocks for rtc"). This insertion shifted most
nummerical clock assignments to a new nummerical value which in turn
rendered most hardcoded nummeric values in imx35.dtsi incorrect.
Restore the existing order by moving the newly introduced clock to the
end of the enum. Update the dts documentation accordingly.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Fixes: 3713e3f5e9 ("clk: imx35: define two clocks for rtc")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ff5fa3c67 upstream.
After initially connecting a wired Xbox 360 controller or sending it
a command to change LEDs, a status/response packet is interpreted as
controller input. This causes the state of buttons represented in
byte 2 of the controller data packet to be incorrect until the next
valid input packet. Wireless Xbox 360 controllers are not affected.
Writing a new value to the LED device while holding the Start button
and running jstest is sufficient to reproduce this bug. An event will
come through with the Start button released.
Xboxdrv also won't attempt to read controller input from a packet
where byte 0 is non-zero. It also checks that byte 1 is 0x14, but
that value differs between wired and wireless controllers and this
code is shared by both. I think just checking byte 0 is enough to
eliminate unwanted packets.
The following are some examples of 3-byte status packets I saw:
01 03 02
02 03 00
03 03 03
08 03 00
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit affa80bd97 upstream.
When running a 32-bit userspace on a 64-bit kernel, the UI_SET_PHYS
ioctl needs to be treated with special care, as it has the pointer
size encoded in the command.
Signed-off-by: Ricky Liang <jcliang@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d3030d1196 upstream.
The ak4642 driver is using a regmap cache sync to restore the
configuration of the chip on resume but (as Peter observed) does not
actually define a register cache which means that the resume is never
going to work and we trigger asserts in regmap. Fix this by enabling
caching.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 01d6e08711 upstream.
Commit c8f33d0bec ("affs: kstrdup() memory handling") checks if the
kstrdup function returns NULL due to out-of-memory condition.
However, if we are remounting a filesystem with no change to
filesystem-specific options, the parameter data is NULL. In this case,
kstrdup returns NULL (because it was passed NULL parameter), although no
out of memory condition exists. The mount syscall then fails with
ENOMEM.
This patch fixes the bug. We fail with ENOMEM only if data is non-NULL.
The patch also changes the call to replace_mount_options - if we didn't
pass any filesystem-specific options, we don't call
replace_mount_options (thus we don't erase existing reported options).
Fixes: c8f33d0bec ("affs: kstrdup() memory handling")
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 94cc36b84a upstream.
Avoid an aliasing issue causing a build error in VDSO:
In file included from include/linux/srcu.h:34:0,
from include/linux/notifier.h:15,
from ./arch/mips/include/asm/uprobes.h:9,
from include/linux/uprobes.h:61,
from include/linux/mm_types.h:13,
from ./arch/mips/include/asm/vdso.h:14,
from arch/mips/vdso/vdso.h:27,
from arch/mips/vdso/gettimeofday.c:11:
include/linux/workqueue.h: In function 'work_static':
include/linux/workqueue.h:186:2: error: dereferencing type-punned pointer will break strict-aliasing rules [-Werror=strict-aliasing]
return *work_data_bits(work) & WORK_STRUCT_STATIC;
^
cc1: all warnings being treated as errors
make[2]: *** [arch/mips/vdso/gettimeofday.o] Error 1
with a CONFIG_DEBUG_OBJECTS_WORK configuration and GCC 5.2.0. Include
`-fno-strict-aliasing' along with compiler options used, as required for
kernel code, fixing a problem present since the introduction of VDSO
with commit ebb5e78cc6 ("MIPS: Initial implementation of a VDSO").
Thanks to Tejun for diagnosing this properly!
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Fixes: ebb5e78cc6 ("MIPS: Initial implementation of a VDSO")
Cc: Tejun Heo <tj@kernel.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13357/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 13eb192d10 upstream.
In microMIPS kernels, handle_signal() sets the isa16 mode bit in the
vdso address so that the sigreturn trampolines (which are offset from
the VDSO) get executed as microMIPS.
However commit ebb5e78cc6 ("MIPS: Initial implementation of a VDSO")
changed the offsets to come from the VDSO image, which already have the
isa16 mode bit set correctly since they're extracted from the VDSO
shared library symbol table.
Drop the isa16 mode bit handling from handle_signal() to fix sigreturn
for cores which support both microMIPS and normal MIPS. This doesn't fix
microMIPS only cores, since the VDSO is still built for normal MIPS, but
thats a separate problem.
Fixes: ebb5e78cc6 ("MIPS: Initial implementation of a VDSO")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13348/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit abf378be49 upstream.
Correct the cases missed with commit 9b26616c8d ("MIPS: Respect the
ISA level in FCSR handling") and prevent writes to read-only FCSR bits
there.
This in particular applies to FP context initialisation where any IEEE
754-2008 bits preset by `mips_set_personality_nan' are cleared before
the relevant ptrace(2) call takes effect and the PTRACE_POKEUSR request
addressing FPC_CSR where no masking of read-only FCSR bits is done.
Remove the FCSR clearing from FP context initialisation then and unify
PTRACE_POKEUSR/FPC_CSR and PTRACE_SETFPREGS handling, by factoring out
code from `ptrace_setfpregs' and calling it from both places.
This mostly matters to soft float configurations where the emulator can
be switched this way to a mode which should not be accessible and cannot
be set with the CTC1 instruction. With hard float configurations any
effect is transient anyway as read-only bits will retain their values at
the time the FP context is restored.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13239/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4249548454 upstream.
Fix a floating-point context restoration regression introduced with
commit 9b26616c8d ("MIPS: Respect the ISA level in FCSR handling")
that causes a Floating Point exception and consequently a kernel oops
with hard float configurations when one or more FCSR Enable and their
corresponding Cause bits are set both at a time via a ptrace(2) call.
To do so reinstate Cause bit masking originally introduced with commit
b1442d39fa ("MIPS: Prevent user from setting FCSR cause bits") to
address this exact problem and then inadvertently removed from the
PTRACE_SETFPREGS request with the commit referred above.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13238/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6533af4d48 upstream.
If a kernel doesn't support MSA context (ie. CONFIG_CPU_HAS_MSA=n) then
it will only keep 64 bits per FP register in thread context, and the
calls to set_fpr64 in restore_msa_extcontext will overrun the end of the
FP register context into the FCSR & MSACSR values. GCC 6.x has become
smart enough to detect this & complain like so:
arch/mips/kernel/signal.c: In function 'protected_restore_fp_context':
./arch/mips/include/asm/processor.h:114:17: error: array subscript is above array bounds [-Werror=array-bounds]
fpr->val##width[FPR_IDX(width, idx)] = val; \
~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~
./arch/mips/include/asm/processor.h:118:1: note: in expansion of macro 'BUILD_FPR_ACCESS'
BUILD_FPR_ACCESS(64)
The only way to trigger this code to run would be for a program to set
up an artificial extended MSA context structure following a sigframe &
execute sigreturn. Whilst this doesn't allow a program to write to any
state that it couldn't already, it makes little sense to allow this
"restoration" of MSA context in a system that doesn't support MSA.
Fix this by killing a program with SIGSYS if it tries something as crazy
as "restoring" fake MSA context in this way, also fixing the build error
& allowing for most of restore_msa_extcontext to be optimised out of
kernels without support for MSA.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reported-by: Michal Toman <michal.toman@imgtec.com>
Fixes: bf82cb30c7 ("MIPS: Save MSA extended context around signals")
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Michal Toman <michal.toman@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13164/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b8322576e upstream.
Commit 9791554b45 ("MIPS,prctl: add PR_[GS]ET_FP_MODE prctl options
for MIPS") added support for the PR_SET_FP_MODE prctl, which allows a
userland program to modify its FP mode at runtime. This is most notably
required if dynamic linking leads to the FP mode requirement changing at
runtime from that indicated in the initial executable's ELF header. In
order to avoid overhead in the general FP context restore code, it aimed
to have threads in the process become unable to enable the FPU during a
mode switch & have the thread calling the prctl syscall wait for all
other threads in the process to be context switched at least once. Once
that happens we can know that no thread in the process whose mode will
be switched has live FP context, and it's safe to perform the mode
switch. However in the (rare) case of modeswitches occurring in
multithreaded programs this can lead to indeterminate delays for the
thread invoking the prctl syscall, and the code monitoring for those
context switches was woefully inadequate for all but the simplest cases.
Fix this by broadcasting an IPI if other CPUs may have live FP context
for an affected thread, with a handler causing those CPUs to relinquish
their FPU ownership. Threads will then be allowed to continue running
but will stall on the wait_on_atomic_t in enable_restore_fp_context if
they attempt to use FP again whilst the mode switch is still in
progress. The end result is less fragile poking at scheduler context
switch counts & a more expedient completion of the mode switch.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: 9791554b45 ("MIPS,prctl: add PR_[GS]ET_FP_MODE prctl options for MIPS")
Reviewed-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: Adam Buchbinder <adam.buchbinder@gmail.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13145/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a3c8b48ac upstream.
In revision 1.12 of the MSA specification, the copy_u.w instruction has
been removed for MIPS32 & the copy_u.d instruction has been removed for
MIPS64. Newer toolchains (eg. Codescape SDK essentials 2015.10) will
complain about this like so:
arch/mips/kernel/r4k_fpu.S:290: Error: opcode not supported on this
processor: mips32r2 (mips32r2) `copy_u.w $1,$w26[3]'
Since we always copy to the width of a GPR, simply use copy_s instead of
copy_u to fix this.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13061/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f5b556c94c upstream.
This makes the ath79 bootconsole behave the same way as the generic 8250
bootconsole.
Also waiting for TEMT (transmit buffer is empty) instead of just THRE
(transmit buffer is not full) ensures that all characters have been
transmitted before the real serial driver starts reconfiguring the serial
controller (which would sometimes result in garbage being transmitted.)
This change does not cause a visible performance loss.
In addition, this seems to fix a hang observed in certain configurations on
many AR7xxx/AR9xxx SoCs during autoconfig of the real serial driver.
A more complete follow-up patch will disable 8250 autoconfig for ath79
altogether (the serial controller is detected as a 16550A, which is not
fully compatible with the ath79 serial, and the autoconfig may lead to
undefined behavior on ath79.)
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 37d22a0d79 upstream.
It's possible for pages to become visible prior to update_mmu_cache
running if a thread within the same address space preempts the current
thread or runs simultaneously on another CPU. That is, the following
scenario is possible:
CPU0 CPU1
write to page
flush_dcache_page
flush_icache_page
set_pte_at
map page
update_mmu_cache
If CPU1 maps the page in between CPU0's set_pte_at, which marks it valid
& visible, and update_mmu_cache where the dcache flush occurs then CPU1s
icache will fill from stale data (unless it fills from the dcache, in
which case all is good, but most MIPS CPUs don't have this property).
Commit 4d46a67a3e ("MIPS: Fix race condition in lazy cache flushing.")
attempted to fix that by performing the dcache flush in
flush_icache_page such that it occurs before the set_pte_at call makes
the page visible. However it has the problem that not all code that
writes to pages exposed to userland call flush_icache_page. There are
many callers of set_pte_at under mm/ and only 2 of them do call
flush_icache_page. Thus the race window between a page becoming visible
& being coherent between the icache & dcache remains open in some cases.
To illustrate some of the cases, a WARN was added to __update_cache with
this patch applied that triggered in cases where a page about to be
flushed from the dcache was not the last page provided to
flush_icache_page. That is, backtraces were obtained for cases in which
the race window is left open without this patch. The 2 standout examples
follow.
When forking a process:
[ 15.271842] [<80417630>] __update_cache+0xcc/0x188
[ 15.277274] [<80530394>] copy_page_range+0x56c/0x6ac
[ 15.282861] [<8042936c>] copy_process.part.54+0xd40/0x17ac
[ 15.289028] [<80429f80>] do_fork+0xe4/0x420
[ 15.293747] [<80413808>] handle_sys+0x128/0x14c
When exec'ing an ELF binary:
[ 14.445964] [<80417630>] __update_cache+0xcc/0x188
[ 14.451369] [<80538d88>] move_page_tables+0x414/0x498
[ 14.457075] [<8055d848>] setup_arg_pages+0x220/0x318
[ 14.462685] [<805b0f38>] load_elf_binary+0x530/0x12a0
[ 14.468374] [<8055ec3c>] search_binary_handler+0xbc/0x214
[ 14.474444] [<8055f6c0>] do_execveat_common+0x43c/0x67c
[ 14.480324] [<8055f938>] do_execve+0x38/0x44
[ 14.485137] [<80413808>] handle_sys+0x128/0x14c
These code paths write into a page, call flush_dcache_page then call
set_pte_at without flush_icache_page inbetween. The end result is that
the icache can become corrupted & userland processes may execute
unexpected or invalid code, typically resulting in a reserved
instruction exception, a trap or a segfault.
Fix this race condition fully by performing any cache maintenance
required to keep the icache & dcache in sync in set_pte_at, before the
page is made valid. This has the added bonus of ensuring the cache
maintenance always happens in one location, rather than being duplicated
in flush_icache_page & update_mmu_cache. It also matches the way other
architectures solve the same problem (see arm, ia64 & powerpc).
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reported-by: Ionela Voinescu <ionela.voinescu@imgtec.com>
Cc: Lars Persson <lars.persson@axis.com>
Fixes: 4d46a67a3e ("MIPS: Fix race condition in lazy cache flushing.")
Cc: Steven J. Hill <sjhill@realitydiluted.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12722/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 234859e49a upstream.
When flush_dcache_page is called on an executable page, that page is
about to be provided to userland & we can presume that the icache
contains no valid entries for its address range. However if the icache
does not fill from the dcache then we cannot presume that the pages
content has been written back as far as the memories that the dcache
will fill from (ie. L2 or further out).
This was being done for lowmem pages, but not for highmem which can lead
to icache corruption. Fix this by mapping highmem pages & flushing their
content from the dcache in __flush_dcache_page before providing the page
to userland, just as is done for lowmem pages.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Lars Persson <lars.persson@axis.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12720/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a7e89326b4 upstream.
Commit f51246efee ("MIPS: Get rid of finish_arch_switch().") moved the
__restore_watch() call from finish_arch_switch() (i.e. after resume()
returns) to before the resume() call in switch_to(). This results in
watchpoints only being restored when a task is descheduled, preventing
the watchpoints from being effective most of the time, except due to
chance before the watchpoints are lazily removed.
Fix the call sequence from switch_to() through to
mips_install_watch_registers() to pass the task_struct pointer of the
next task, instead of using current. This allows the watchpoints for the
next (non-current) task to be restored without reintroducing
finish_arch_switch().
Fixes: f51246efee ("MIPS: Get rid of finish_arch_switch().")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12726/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 987e5b8344 upstream.
Since commit 8cb48fe169 ("MIPS: Provide correct siginfo_t.si_stime"),
MIPS' uapi/asm/siginfo.h has included uapi/asm-generic/siginfo.h
directly before defining MIPS' struct siginfo, in order to get the
necessary definitions needed for the siginfo struct without the generic
copy_siginfo() hitting compiler errors due to struct siginfo not yet
being defined.
Now that the generic copy_siginfo() is moved out to linux/signal.h we
can safely include asm-generic/siginfo.h before defining the MIPS
specific struct siginfo, which avoids the uapi/ include as well as
breakage due to generic copy_siginfo() being defined before struct
siginfo.
Reported-by: Christopher Ferris <cferris@google.com>
Fixes: 8cb48fe169 ("MIPS: Provide correct siginfo_t.si_stime")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Petr Malat <oss@malat.biz>
Cc: linux-mips@linux-mips.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81a76d7119 upstream.
When showing backtraces in response to traps, for example crashes and
address errors (usually unaligned accesses) when they are set in debugfs
to be reported, unwind_stack will be used if the PC was in the kernel
text address range. However since EVA it is possible for user and kernel
address ranges to overlap, and even without EVA userland can still
trigger an address error by jumping to a KSeg0 address.
Adjust the check to also ensure that it was running in kernel mode. I
don't believe any harm can come of this problem, since unwind_stack() is
sufficiently defensive, however it is only meant for unwinding kernel
code, so to be correct it should use the raw backtracing instead.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11701/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
(cherry picked from commit d2941a975ac745c607dfb590e92bb30bc352dad9)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a816b306c6 upstream.
When unwinding through IRQs and exceptions, the unwinding only continues
if the PC is a kernel text address, however since EVA it is possible for
user and kernel address ranges to overlap, potentially allowing
unwinding to continue to user mode if the user PC happens to be in the
kernel text address range.
Adjust the check to also ensure that the register state from before the
exception is actually running in kernel mode, i.e. !user_mode(regs).
I don't believe any harm can come of this problem, since the PC is only
output, the stack pointer is checked to ensure it resides within the
task's stack page before it is dereferenced in search of the return
address, and the return address register is similarly only output (if
the PC is in a leaf function or the beginning of a non-leaf function).
However unwind_stack() is only meant for unwinding kernel code, so to be
correct the unwind should stop there.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11700/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e49d384885 upstream.
Fix a build regression from commit c9017757c5 ("MIPS: init upper 64b
of vector registers when MSA is first used"):
arch/mips/built-in.o: In function `enable_restore_fp_context':
traps.c:(.text+0xbb90): undefined reference to `_init_msa_upper'
traps.c:(.text+0xbb90): relocation truncated to fit: R_MIPS_26 against `_init_msa_upper'
traps.c:(.text+0xbef0): undefined reference to `_init_msa_upper'
traps.c:(.text+0xbef0): relocation truncated to fit: R_MIPS_26 against `_init_msa_upper'
to !CONFIG_CPU_HAS_MSA configurations with older GCC versions, which are
unable to figure out that calls to `_init_msa_upper' are indeed dead.
Of the many ways to tackle this failure choose the approach we have
already taken in `thread_msa_context_live'.
[ralf@linux-mips.org: Drop patch segment to junk file.]
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13271/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ab4a92e667 upstream.
When emulating a jalr instruction with rd == $0, the code in
isBranchInstr was incorrectly writing to GPR $0 which should actually
always remain zeroed. This would lead to any further instructions
emulated which use $0 operating on a bogus value until the task is next
context switched, at which point the value of $0 in the task context
would be restored to the correct zero by a store in SAVE_SOME. Fix this
by not writing to rd if it is $0.
Fixes: 102cedc32a ("MIPS: microMIPS: Floating point support.")
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Maciej W. Rozycki <macro@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13160/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c9c6837d39 upstream.
gcc-6 started warning by default about variables that are not
used anywhere and that are marked 'const', generating many
false positives in an allmodconfig build, e.g.:
arch/arm/mach-davinci/board-da830-evm.c:282:20: warning: 'da830_evm_emif25_pins' defined but not used [-Wunused-const-variable=]
arch/arm/plat-omap/dmtimer.c:958:34: warning: 'omap_timer_match' defined but not used [-Wunused-const-variable=]
drivers/bluetooth/hci_bcm.c:625:39: warning: 'acpi_bcm_default_gpios' defined but not used [-Wunused-const-variable=]
drivers/char/hw_random/omap-rng.c:92:18: warning: 'reg_map_omap4' defined but not used [-Wunused-const-variable=]
drivers/devfreq/exynos/exynos5_bus.c:381:32: warning: 'exynos5_busfreq_int_pm' defined but not used [-Wunused-const-variable=]
drivers/dma/mv_xor.c:1139:34: warning: 'mv_xor_dt_ids' defined but not used [-Wunused-const-variable=]
This is similar to the existing -Wunused-but-set-variable warning
that was added in an earlier release and that we disable by default
now and only enable when W=1 is set, so it makes sense to do
the same here. Once we have eliminated the majority of the
warnings for both, we can put them back into the default list.
We probably want this in backport kernels as well, to allow building
them with gcc-6 without introducing extra warnings.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Michal Marek <mmarek@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 305c2e71b3 upstream.
Now that we've done a more comprehensive fix with the intermediate
target state we can remove the previous hack introduced with commit
90a88d6ef8 ("scsi: fix soft lockup in scsi_remove_target() on module
removal").
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f05795d3d7 upstream.
Add intermediate STARGET_REMOVE state to scsi_target_state to avoid
running into the BUG_ON() in scsi_target_reap(). The STARGET_REMOVE
state is only valid in the path from scsi_remove_target() to
scsi_target_destroy() indicating this target is going to be removed.
This re-fixes the problem introduced in commits bc3f02a795 ("[SCSI]
scsi_remove_target: fix softlockup regression on hot remove") and
4099819356 ("scsi: restart list search after unlock in
scsi_remove_target") in a more comprehensive way.
[mkp: Included James' fix for scsi_target_destroy()]
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Fixes: 4099819356
Reported-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Tested-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: James Bottomley <jejb@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 037369b872 upstream.
The HPFS filesystem used generic_show_options to produce string that is
displayed in /proc/mounts. However, there is a problem that the options
may disappear after remount. If we mount the filesystem with option1
and then remount it with option2, /proc/mounts should show both option1
and option2, however it only shows option2 because the whole option
string is replaced with replace_mount_options in hpfs_remount_fs.
To fix this bug, implement the hpfs_show_options function that prints
options that are currently selected.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 44d51706b4 upstream.
Commit ce657611ba ("hpfs: kstrdup() out of memory handling") checks if
the kstrdup function returns NULL due to out-of-memory condition.
However, if we are remounting a filesystem with no change to
filesystem-specific options, the parameter data is NULL. In this case,
kstrdup returns NULL (because it was passed NULL parameter), although no
out of memory condition exists. The mount syscall then fails with
ENOMEM.
This patch fixes the bug. We fail with ENOMEM only if data is non-NULL.
The patch also changes the call to replace_mount_options - if we didn't
pass any filesystem-specific options, we don't call
replace_mount_options (thus we don't erase existing reported options).
Fixes: ce657611ba ("hpfs: kstrdup() out of memory handling")
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1900149c83 upstream.
Ezequiel reported that he's facing UBI going into read-only
mode after power cut. It turned out that this behavior happens
only when updating a static volume is interrupted and Fastmap is
used.
A possible trace can look like:
ubi0 warning: ubi_io_read_vid_hdr [ubi]: no VID header found at PEB 2323, only 0xFF bytes
ubi0 warning: ubi_eba_read_leb [ubi]: switch to read-only mode
CPU: 0 PID: 833 Comm: ubiupdatevol Not tainted 4.6.0-rc2-ARCH #4
Hardware name: SAMSUNG ELECTRONICS CO., LTD. 300E4C/300E5C/300E7C/NP300E5C-AD8AR, BIOS P04RAP 10/15/2012
0000000000000286 00000000eba949bd ffff8800c45a7b38 ffffffff8140d841
ffff8801964be000 ffff88018eaa4800 ffff8800c45a7bb8 ffffffffa003abf6
ffffffff850e2ac0 8000000000000163 ffff8801850e2ac0 ffff8801850e2ac0
Call Trace:
[<ffffffff8140d841>] dump_stack+0x63/0x82
[<ffffffffa003abf6>] ubi_eba_read_leb+0x486/0x4a0 [ubi]
[<ffffffffa00453b3>] ubi_check_volume+0x83/0xf0 [ubi]
[<ffffffffa0039d97>] ubi_open_volume+0x177/0x350 [ubi]
[<ffffffffa00375d8>] vol_cdev_open+0x58/0xb0 [ubi]
[<ffffffff8124b08e>] chrdev_open+0xae/0x1d0
[<ffffffff81243bcf>] do_dentry_open+0x1ff/0x300
[<ffffffff8124afe0>] ? cdev_put+0x30/0x30
[<ffffffff81244d36>] vfs_open+0x56/0x60
[<ffffffff812545f4>] path_openat+0x4f4/0x1190
[<ffffffff81256621>] do_filp_open+0x91/0x100
[<ffffffff81263547>] ? __alloc_fd+0xc7/0x190
[<ffffffff812450df>] do_sys_open+0x13f/0x210
[<ffffffff812451ce>] SyS_open+0x1e/0x20
[<ffffffff81a99e32>] entry_SYSCALL_64_fastpath+0x1a/0xa4
UBI checks static volumes for data consistency and reads the
whole volume upon first open. If the volume is found erroneous
users of UBI cannot read from it, but another volume update is
possible to fix it. The check is performed by running
ubi_eba_read_leb() on every allocated LEB of the volume.
For static volumes ubi_eba_read_leb() computes the checksum of all
data stored in a LEB. To verify the computed checksum it has to read
the LEB's volume header which stores the original checksum.
If the volume header is not found UBI treats this as fatal internal
error and switches to RO mode. If the UBI device was attached via a
full scan the assumption is correct, the volume header has to be
present as it had to be there while scanning to get known as mapped.
If the attach operation happened via Fastmap the assumption is no
longer correct. When attaching via Fastmap UBI learns the mapping
table from Fastmap's snapshot of the system state and not via a full
scan. It can happen that a LEB got unmapped after a Fastmap was
written to the flash. Then UBI can learn the LEB still as mapped and
accessing it returns only 0xFF bytes. As UBI is not a FTL it is
allowed to have mappings to empty PEBs, it assumes that the layer
above takes care of LEB accounting and referencing.
UBIFS does so using the LEB property tree (LPT).
For static volumes UBI blindly assumes that all LEBs are present and
therefore special actions have to be taken.
The described situation can happen when updating a static volume is
interrupted, either by a user or a power cut.
The volume update code first unmaps all LEBs of a volume and then
writes LEB by LEB. If the sequence of operations is interrupted UBI
detects this either by the absence of LEBs, no volume header present
at scan time, or corrupted payload, detected via checksum.
In the Fastmap case the former method won't trigger as no scan
happened and UBI automatically thinks all LEBs are present.
Only by reading data from a LEB it detects that the volume header is
missing and incorrectly treats this as fatal error.
To deal with the situation ubi_eba_read_leb() from now on checks
whether we attached via Fastmap and handles the absence of a
volume header like a data corruption error.
This way interrupted static volume updates will correctly get detected
also when Fastmap is used.
Reported-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c63c2454e upstream.
32-bit ioctl uses these rather than the regular FS_IOC_* versions. They can
be handled in btrfs using the same code. Without this, 32-bit {ch,ls}attr
fail.
Signed-off-by: Luke Dashjr <luke-jr+git@utopios.org>
Reviewed-by: Josef Bacik <jbacik@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca9eb49aa9 upstream.
The generic copy_siginfo() is currently defined in
asm-generic/siginfo.h, after including uapi/asm-generic/siginfo.h which
defines the generic struct siginfo. However this makes it awkward for an
architecture to use it if it has to define its own struct siginfo (e.g.
MIPS and potentially IA64), since it means that asm-generic/siginfo.h
can only be included after defining the arch-specific siginfo, which may
be problematic if the arch-specific definition needs definitions from
uapi/asm-generic/siginfo.h.
It is possible to work around this by first including
uapi/asm-generic/siginfo.h to get the constants before defining the
arch-specific siginfo, and include asm-generic/siginfo.h after. However
uapi headers can't be included by other uapi headers, so that first
include has to be in an ifdef __kernel__, with the non __kernel__ case
including the non-UAPI header instead.
Instead of that mess, move the generic copy_siginfo() definition into
linux/signal.h, which allows an arch-specific uapi/asm/siginfo.h to
include asm-generic/siginfo.h and define the arch-specific siginfo, and
for the generic copy_siginfo() to see that arch-specific definition.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Petr Malat <oss@malat.biz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Christopher Ferris <cferris@google.com>
Cc: linux-arch@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-ia64@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12478/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 092398dce8 upstream.
Introduced by upstream commit 70d9798b95
The raid0 personality does not create mddev->thread as oposed to
other personalities leading to its unconditional access in
mddev_suspend() causing an oops.
Patch checks for mddev->thread in order to keep the
intention of aforementioned commit.
Fixes: 70d9798b95 ("MD: warn for potential deadlock")
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2ffa9a5d76 upstream.
If tb_drom_read() fails, sw->drom is freed but not set to NULL. sw->drom
is then freed again in the error path of tb_switch_alloc().
The bug can be triggered by unplugging a thunderbolt device shortly after
it is detected by the thunderbolt driver.
Clear sw->drom if tb_drom_read() fails.
[bhelgaas: add Fixes:, stable versions of interest]
Fixes: 343fcb8c70 ("thunderbolt: Fix nontrivial endpoint devices.")
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 86c72d1ce9 upstream.
Add the pin configuration value of this machine into the pin_quirk
table to make DELL1_MIC_NO_PRESENCE apply to this machine.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 423cd78561 upstream.
The headphone has noise when playing sound or switching microphone sources.
It uses the same codec on XPS 13 9350, but with different subsystem ID.
Applying the fixup can solve the issue.
Also, changing the model name to better differentiate models.
v2: Reorder by device ID.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dcd4f0db61 upstream.
Support new codecs for ALC234/ALC274/ALC294.
This three codecs was the same IC.
But bonding is not the same.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f75564d343 upstream.
The bar number is found in reg2 within the gdd. Therefore
we need to change the assigment from reg1 to reg2 which
is the correct location.
Signed-off-by: Andreas Werner <andreas.werner@men.de>
Fixes: '3764e82e5' drivers: Introduce MEN Chameleon Bus
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46856fabe4 upstream.
Commits 190aa4304d (Add AMD Mullins platform support) and
cca118fa2a (Add AMD Carrizo platform support) enabled the
driver on a lot more devices, but the following commit missed
a single location in the code when checking if the SB800 register
offsets should be used. This leads to the wrong register being
written which in turn causes ACPI to go haywire.
Fix this by introducing a helper function to check for the new
register layout and use this consistently.
https://bugzilla.kernel.org/show_bug.cgi?id=114201https://bugzilla.redhat.com/show_bug.cgi?id=1329910
Fixes: bdecfcdb54 (sp5100_tco: fix the device check for SB800
and later chipsets)
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ec36a5c668 upstream.
Add missing locking to:
* bcm2835_pll_divider_on
* bcm2835_pll_divider_off
to protect the read modify write cycle for the
register access protecting both cm_reg and a2w_reg
registers.
Fixes: 41691b8862 ("clk: bcm2835: Add support for programming the
audio domain clocks")
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54cf809b95 upstream.
Similar to commits:
51d7d5205d ("powerpc: Add smp_mb() to arch_spin_is_locked()")
d86b8da04d ("arm64: spinlock: serialise spin_unlock_wait against concurrent lockers")
qspinlock suffers from the fact that the _Q_LOCKED_VAL store is
unordered inside the ACQUIRE of the lock.
And while this is not a problem for the regular mutual exclusive
critical section usage of spinlocks, it breaks creative locking like:
spin_lock(A) spin_lock(B)
spin_unlock_wait(B) if (!spin_is_locked(A))
do_something() do_something()
In that both CPUs can end up running do_something at the same time,
because our _Q_LOCKED_VAL store can drop past the spin_unlock_wait()
spin_is_locked() loads (even on x86!!).
To avoid making the normal case slower, add smp_mb()s to the less used
spin_unlock_wait() / spin_is_locked() side of things to avoid this
problem.
Reported-and-tested-by: Davidlohr Bueso <dave@stgolabs.net>
Reported-by: Giovanni Gherdovich <ggherdovich@suse.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b8995f527a upstream.
This patch fixes the broken serial log when changing the clock source
of uart device. Before disabling the original clock source, this patch
enables the new clock source to protect the clock off state for a split second.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
commit c42850f1ae upstream.
There is a special register that shows interrupt status by source. In
particular case the source can be a combination of DMA Tx, DMA Rx, and UART.
Read the register and call the handlers only for sources that request an
interrupt.
Fixes: 6ede6dcd87 ("serial: 8250_mid: add support for DMA engine handling from UART MMIO")
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 107e15fc1f upstream.
Unlike Intel Medfield and Tangier platforms DNV uses PCI BAR0 for IO compatible
resources and BAR1 for MMIO. We need latter in a way to support DMA. Introduce
an additional field in the internal structure and pass PCI BAR based on device
ID.
Reported-by: "Lai, Poey Seng" <poey.seng.lai@intel.com>
Fixes: 6ede6dcd87 ("serial: 8250_mid: add support for DMA engine handling from UART MMIO")
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f210c18c1 upstream.
Since commit 21947ba654 ("serial: 8250_pci: replace switch-case by
formula"), the 8250 driver crashes in the byt_set_termios() function
with a divide error. This is caused by the fact that a baud rate of 0 (B0)
is not handled properly. Fix it by falling back to B9600 in this case.
Signed-off-by: David Müller <d.mueller@elsoft.ch>
Fixes: 21947ba654 ("serial: 8250_pci: replace switch-case by formula")
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5be605ac9a upstream.
Commit 1cf6e8fc83 ("tty/serial: at91: fix RTS line management when
hardware handshake is enabled") actually allowed to enable hardware
handshaking.
Before, the CRTSCTS flags was silently ignored.
As the DMA controller can't drive RTS (as explain in the commit message).
Ensure that hardware flow control stays disabled when DMA is used and FIFOs
are not available.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Fixes: 1cf6e8fc83 ("tty/serial: at91: fix RTS line management when hardware handshake is enabled")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d175feca89 upstream.
Dmitry reported, that the current cleanup code in n_gsm can trigger a
warning:
WARNING: CPU: 2 PID: 24238 at drivers/tty/n_gsm.c:2048 gsm_cleanup_mux+0x166/0x6b0()
...
Call Trace:
...
[<ffffffff81247ab9>] warn_slowpath_null+0x29/0x30 kernel/panic.c:490
[<ffffffff828d0456>] gsm_cleanup_mux+0x166/0x6b0 drivers/tty/n_gsm.c:2048
[<ffffffff828d4d87>] gsmld_open+0x5b7/0x7a0 drivers/tty/n_gsm.c:2386
[<ffffffff828b9078>] tty_ldisc_open.isra.2+0x78/0xd0 drivers/tty/tty_ldisc.c:447
[<ffffffff828b973a>] tty_set_ldisc+0x1ca/0xa70 drivers/tty/tty_ldisc.c:567
[< inline >] tiocsetd drivers/tty/tty_io.c:2650
[<ffffffff828a14ea>] tty_ioctl+0xb2a/0x2140 drivers/tty/tty_io.c:2883
...
But this is a legal path when open fails to find a space in the
gsm_mux array and tries to clean up. So make it a standard test
instead of a warning.
Reported-by: "Dmitry Vyukov" <dvyukov@google.com>
Cc: Alan Cox <alan@linux.intel.com>
Link: http://lkml.kernel.org/r/CACT4Y+bHQbAB68VFi7Romcs-Z9ZW3kQRvcq+BvHH1oa5NcAdLA@mail.gmail.com
Fixes: 5a640967 ("tty/n_gsm.c: fix a memory leak in gsmld_open()")
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6798df4c5f upstream.
When csw->con_startup() fails in do_register_con_driver, we return no
error (i.e. 0). This was changed back in 2006 by commit 3e795de763.
Before that we used to return -ENODEV.
So fix the return value to be -ENODEV in that case again.
Fixes: 3e795de763 ("VT binding: Add binding/unbinding support for the VT console")
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: "Dan Carpenter" <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e8df1a95b6 upstream.
When I added support for the Memory Protection Keys processor
feature, I had to reindent the REQUIRED/DISABLED_MASK macros, and
also consult the later cpufeature words.
I'm not quite sure how I bungled it, but I consulted the wrong
word at the end. This only affected required or disabled cpu
features in cpufeature words 14, 15 and 16. So, only Protection
Keys itself was screwed over here.
The result was that if you disabled pkeys in your .config, you
might still see some code show up that should have been compiled
out. There should be no functional problems, though.
In verifying this patch I also realized that the DISABLE_PKU/OSPKE
macros were defined backwards and that the cpu_has() check in
setup_pku() was not doing the compile-time disabled checks.
So also fix the macro for DISABLE_PKU/OSPKE and add a compile-time
check for pkeys being enabled in setup_pku().
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Dave Hansen <dave@sr71.net>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Fixes: dfb4a70f20 ("x86/cpufeature, x86/mm/pkeys: Add protection keys related CPUID definitions")
Link: http://lkml.kernel.org/r/20160513221328.C200930B@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 702f926067 upstream.
b4ff8389ed is incomplete: relies on nr_legacy_irqs() to get the number
of legacy interrupts when actually nr_legacy_irqs() returns 0 after
probe_8259A(). Use NR_IRQS_LEGACY instead.
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b45bacd2d0 upstream.
Writing CP0_Compare clears the timer interrupt pending bit
(CP0_Cause.TI), but this wasn't being done atomically. If a timer
interrupt raced with the write of the guest CP0_Compare, the timer
interrupt could end up being pending even though the new CP0_Compare is
nowhere near CP0_Count.
We were already updating the hrtimer expiry with
kvm_mips_update_hrtimer(), which used both kvm_mips_freeze_hrtimer() and
kvm_mips_resume_hrtimer(). Close the race window by expanding out
kvm_mips_update_hrtimer(), and clearing CP0_Cause.TI and setting
CP0_Compare between the freeze and resume. Since the pending timer
interrupt should not be cleared when CP0_Compare is written via the KVM
user API, an ack argument is added to distinguish the source of the
write.
Fixes: e30492bbe9 ("MIPS: KVM: Rewrite count/compare timer emulation")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim KrÄmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4355c44f06 upstream.
There's a particularly narrow and subtle race condition when the
software emulated guest timer is frozen which can allow a guest timer
interrupt to be missed.
This happens due to the hrtimer expiry being inexact, so very
occasionally the freeze time will be after the moment when the emulated
CP0_Count transitions to the same value as CP0_Compare (so an IRQ should
be generated), but before the moment when the hrtimer is due to expire
(so no IRQ is generated). The IRQ won't be generated when the timer is
resumed either, since the resume CP0_Count will already match CP0_Compare.
With VZ guests in particular this is far more likely to happen, since
the soft timer may be frozen frequently in order to restore the timer
state to the hardware guest timer. This happens after 5-10 hours of
guest soak testing, resulting in an overflow in guest kernel timekeeping
calculations, hanging the guest. A more focussed test case to
intentionally hit the race (with the help of a new hypcall to cause the
timer state to migrated between hardware & software) hits the condition
fairly reliably within around 30 seconds.
Instead of relying purely on the inexact hrtimer expiry to determine
whether an IRQ should be generated, read the guest CP0_Compare and
directly check whether the freeze time is before or after it. Only if
CP0_Count is on or after CP0_Compare do we check the hrtimer expiry to
determine whether the last IRQ has already been generated (which will
have pushed back the expiry by one timer period).
Fixes: e30492bbe9 ("MIPS: KVM: Rewrite count/compare timer emulation")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim KrÄmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07f8ab255f upstream.
When CONFIG_KVM_XICS is enabled, CPU_UP_PREPARE and other macros for
CPU states in linux/cpu.h are needed by arch/powerpc/kvm/book3s_hv.c.
Otherwise, build error as below is seen:
gwshan@gwshan:~/sandbox/l$ make arch/powerpc/kvm/book3s_hv.o
:
CC arch/powerpc/kvm/book3s_hv.o
arch/powerpc/kvm/book3s_hv.c: In function ‘kvmppc_cpu_notify’:
arch/powerpc/kvm/book3s_hv.c:3072:7: error: ‘CPU_UP_PREPARE’ \
undeclared (first use in this function)
This fixes the issue introduced by commit <6f3bb80944> ("KVM: PPC:
Book3S HV: kvmppc_host_rm_ops - handle offlining CPUs").
Fixes: 6f3bb80944
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f24632475d upstream.
Commit d28bc9dd25 reversed the order of two lines which initialize cr0,
allowing the current (old) cr0 value to mess up vcpu initialization.
This was observed in the checks for cr0 X86_CR0_WP bit in the context of
kvm_mmu_reset_context(). Besides, setting vcpu->arch.cr0 after vmx_set_cr0()
is completely redundant. Change the order back to ensure proper vcpu
initialization.
The combination of booting with ovmf firmware when guest vcpus > 1 and kvm's
ept=N option being set results in a VM-entry failure. This patch fixes that.
Fixes: d28bc9dd25 ("KVM: x86: INIT and reset sequences are different")
Signed-off-by: Bruce Rogers <brogers@suse.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9842df6200 upstream.
MSR 0x2f8 accessed the 124th Variable Range MTRR ever since MTRR support
was introduced by 9ba075a664 ("KVM: MTRR support").
0x2f8 became harmful when 910a6aae4e ("KVM: MTRR: exactly define the
size of variable MTRRs") shrinked the array of VR MTRRs from 256 to 8,
which made access to index 124 out of bounds. The surrounding code only
WARNs in this situation, thus the guest gained a limited read/write
access to struct kvm_arch_vcpu.
0x2f8 is not a valid VR MTRR MSR, because KVM has/advertises only 16 VR
MTRR MSRs, 0x200-0x20f. Every VR MTRR is set up using two MSRs, 0x2f8
was treated as a PHYSBASE and 0x2f9 would be its PHYSMASK, but 0x2f9 was
not implemented in KVM, therefore 0x2f8 could never do anything useful
and getting rid of it is safe.
This fixes CVE-2016-3713.
Fixes: 910a6aae4e ("KVM: MTRR: exactly define the size of variable MTRRs")
Reported-by: David Matlack <dmatlack@google.com>
Signed-off-by: Andy Honig <ahonig@google.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d375278d66 upstream.
DMA is optional with this driver. If it was not enabled the devpriv->dma
pointer will be NULL.
Fix the possible NULL pointer dereference when trying to disable the DMA
channels in das1800_ai_cancel() and tidy up the comments to fix the
checkpatch.pl issues:
WARNING: line over 80 characters
It's probably harmless in das1800_ai_setup_dma() because the 'desc' pointer
will not be used if DMA is disabled but fix it there also.
Fixes: 99dfc3357e ("staging: comedi: das1800: remove depends on ISA_DMA_API limitation")
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f879fc32aa upstream.
The firmware of R-Car USB 3.0 host controller will control the reset.
So, if the xhci driver doesn't do firmware downloading (e.g. kernel
configuration is CONFIG_USB_XHCI_PLATFORM=y and CONFIG_USB_XHCI_RCAR
is not set), the reset of USB 3.0 host controller doesn't work
correctly. Then, the host controller will cause long wait in
xhci_reset() because the CMD_RESET bit of op_regs->command is not
cleared for 10 seconds.
So, this patch modifies the Kconfig to enable both CONFIG_USB_XHCI_PLATFORM
and CONFIG_USB_XHCI_RCAR.
Fixes: 4ac8918f3a (usb: host: xhci-plat: add support for the R-Car H2 and M2 xHCI controllers)
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit feb26ac31a upstream.
The XHCI controller presents two USB buses to the system - one for USB2
and one for USB3. The hub init code (hub_port_init) is reentrant but
only locks one bus per thread, leading to a race condition failure when
two threads attempt to simultaneously initialise a USB2 and USB3 device:
[ 8.034843] xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
[ 13.183701] usb 3-3: device descriptor read/all, error -110
On a test system this failure occurred on 6% of all boots.
The call traces at the point of failure are:
Call Trace:
[<ffffffff81b9bab7>] schedule+0x37/0x90
[<ffffffff817da7cd>] usb_kill_urb+0x8d/0xd0
[<ffffffff8111e5e0>] ? wake_up_atomic_t+0x30/0x30
[<ffffffff817dafbe>] usb_start_wait_urb+0xbe/0x150
[<ffffffff817db10c>] usb_control_msg+0xbc/0xf0
[<ffffffff817d07de>] hub_port_init+0x51e/0xb70
[<ffffffff817d4697>] hub_event+0x817/0x1570
[<ffffffff810f3e6f>] process_one_work+0x1ff/0x620
[<ffffffff810f3dcf>] ? process_one_work+0x15f/0x620
[<ffffffff810f4684>] worker_thread+0x64/0x4b0
[<ffffffff810f4620>] ? rescuer_thread+0x390/0x390
[<ffffffff810fa7f5>] kthread+0x105/0x120
[<ffffffff810fa6f0>] ? kthread_create_on_node+0x200/0x200
[<ffffffff81ba183f>] ret_from_fork+0x3f/0x70
[<ffffffff810fa6f0>] ? kthread_create_on_node+0x200/0x200
Call Trace:
[<ffffffff817fd36d>] xhci_setup_device+0x53d/0xa40
[<ffffffff817fd87e>] xhci_address_device+0xe/0x10
[<ffffffff817d047f>] hub_port_init+0x1bf/0xb70
[<ffffffff811247ed>] ? trace_hardirqs_on+0xd/0x10
[<ffffffff817d4697>] hub_event+0x817/0x1570
[<ffffffff810f3e6f>] process_one_work+0x1ff/0x620
[<ffffffff810f3dcf>] ? process_one_work+0x15f/0x620
[<ffffffff810f4684>] worker_thread+0x64/0x4b0
[<ffffffff810f4620>] ? rescuer_thread+0x390/0x390
[<ffffffff810fa7f5>] kthread+0x105/0x120
[<ffffffff810fa6f0>] ? kthread_create_on_node+0x200/0x200
[<ffffffff81ba183f>] ret_from_fork+0x3f/0x70
[<ffffffff810fa6f0>] ? kthread_create_on_node+0x200/0x200
Which results from the two call chains:
hub_port_init
usb_get_device_descriptor
usb_get_descriptor
usb_control_msg
usb_internal_control_msg
usb_start_wait_urb
usb_submit_urb / wait_for_completion_timeout / usb_kill_urb
hub_port_init
hub_set_address
xhci_address_device
xhci_setup_device
Mathias Nyman explains the current behaviour violates the XHCI spec:
hub_port_reset() will end up moving the corresponding xhci device slot
to default state.
As hub_port_reset() is called several times in hub_port_init() it
sounds reasonable that we could end up with two threads having their
xhci device slots in default state at the same time, which according to
xhci 4.5.3 specs still is a big no no:
"Note: Software shall not transition more than one Device Slot to the
Default State at a time"
So both threads fail at their next task after this.
One fails to read the descriptor, and the other fails addressing the
device.
Fix this in hub_port_init by locking the USB controller (instead of an
individual bus) to prevent simultaneous initialisation of both buses.
Fixes: 638139eb95 ("usb: hub: allow to process more usb hub events in parallel")
Link: https://lkml.org/lkml/2016/2/8/312
Link: https://lkml.org/lkml/2016/2/4/748
Signed-off-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5096c4d3bf upstream.
The argument of dev_err() in usb_gadget_map_request() should be dev
instead of &gadget->dev.
Fixes: 7ace8fc ("usb: gadget: udc: core: Fix argument of dma_map_single for IOMMU")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6fb650d43d upstream.
When a USB driver is bound to an interface (either through probing or
by claiming it) or is unbound from an interface, the USB core always
disables Link Power Management during the transition and then
re-enables it afterward. The reason is because the driver might want
to prevent hub-initiated link power transitions, in which case the HCD
would have to recalculate the various LPM parameters. This
recalculation takes place when LPM is re-enabled and the new
parameters are sent to the device and its parent hub.
However, if the driver does not want to prevent hub-initiated link
power transitions then none of this work is necessary. The parameters
don't need to be recalculated, and LPM doesn't need to be disabled and
re-enabled.
It turns out that disabling and enabling LPM can be time-consuming,
enough so that it interferes with user programs that want to claim and
release interfaces rapidly via usbfs. Since the usbfs kernel driver
doesn't set the disable_hub_initiated_lpm flag, we can speed things up
and get the user programs to work by leaving LPM alone whenever the
flag isn't set.
And while we're improving the way disable_hub_initiated_lpm gets used,
let's also fix its kerneldoc.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Matthew Giassa <matthew@giassa.net>
CC: Mathias Nyman <mathias.nyman@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cdc77c82a8 upstream.
The current implemenentation restart the sent pattern for each entry in
the sg list. The receiving end expects a continuous pattern, and test
will fail unless scatterilst entries happen to be aligned with the
pattern
Fix this by calculating the pattern byte based on total sent size
instead of just the current sg entry.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Fixes: 8b52490193 ("[PATCH] USB: usbtest: scatterlist OUT data pattern testing")
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f78bbcae86 upstream.
When binding the function to usb_configuration, check whether the thread
is running before starting another one. Without that, when function
instance is added to multiple configurations, fsg_bing starts multiple
threads with all but the latest one being forgotten by the driver. This
leads to obvious thread leaks, possible lockups when trying to halt the
machine and possible more issues.
This fixes issues with legacy/multi¹ gadget as well as configfs gadgets
when mass_storage function is added to multiple configurations.
This change also simplifies API since the legacy gadgets no longer need
to worry about starting the thread by themselves (which was where bug
in legacy/multi was in the first place).
N.B., this patch doesn’t address adding single mass_storage function
instance to a single configuration twice. Thankfully, there’s no
legitimate reason for such setup plus, if I’m not mistaken, configfs
gadget doesn’t even allow it to be expressed.
¹ I have no example failure though. Conclusion that legacy/multi has
a bug is based purely on me reading the code.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Tested-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 332a5b446b upstream.
In the current implementation functionfs generates a EFAULT for async read
operations if the read buffer size is larger than the URB data size. Since
a application does not necessarily know how much data the host side is
going to send it typically supplies a buffer larger than the actual data,
which will then result in a EFAULT error.
This behaviour was introduced while refactoring the code to use iov_iter
interface in commit c993c39b86 ("gadget/function/f_fs.c: use put iov_iter
into io_data"). The original code took the minimum over the URB size and
the user buffer size and then attempted to copy that many bytes using
copy_to_user(). If copy_to_user() could not copy all data a EFAULT error
was generated. Restore the original behaviour by only generating a EFAULT
error when the number of bytes copied is not the size of the URB and the
target buffer has not been fully filled.
Commit 342f39a6c8 ("usb: gadget: f_fs: fix check in read operation")
already fixed the same problem for the synchronous read path.
Fixes: c993c39b86 ("gadget/function/f_fs.c: use put iov_iter into io_data")
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 444f94e9e6 upstream.
Added support for Gemalto's Cinterion PH8 and AHxx products
with 2 RmNet Interfaces and products with 1 RmNet + 1 USB Audio interface.
In addition some minor renaming and formatting.
Signed-off-by: Hans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com>
[johan: sort current entries and trim trailing whitespace ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c8d62957d4 upstream.
URBs and buffers allocated in attach for Epic devices would never be
deallocated in case of a later probe error (e.g. failure to allocate
minor numbers) as disconnect is then never called.
Fix by moving deallocation to release and making sure that the
URBs are first unlinked.
Fixes: f9c99bb8b3 ("USB: usb-serial: replace shutdown with disconnect,
release")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c5c0c55598 upstream.
Private data, URBs and buffers allocated for Epic devices during
attach were never released on errors (e.g. missing endpoints).
Fixes: 6e8cf7751f ("USB: add EPIC support to the io_edgeport driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 028c49f5e0 upstream.
The interface read URB is submitted in attach, but was only unlinked by
the driver at disconnect.
In case of a late probe error (e.g. due to failed minor allocation),
disconnect is never called and we would end up with active URBs for an
unbound interface. This in turn could lead to deallocated memory being
dereferenced in the completion callback.
Fixes: f7a33e608d ("USB: serial: add quatech2 usb to serial driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 35be1a71d7 upstream.
The interface instat and indat URBs were submitted in attach, but never
unlinked in release before deallocating the corresponding transfer
buffers.
In the case of a late probe error (e.g. due to failed minor allocation),
disconnect would not have been called before release, causing the
buffers to be freed while the URBs are still in use. We'd also end up
with active URBs for an unbound interface.
Fixes: f9c99bb8b3 ("USB: usb-serial: replace shutdown with disconnect,
release")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9e45284984 upstream.
The interface read and event URBs are submitted in attach, but were
never explicitly unlinked by the driver. Instead the URBs would have
been killed by usb-serial core on disconnect.
In case of a late probe error (e.g. due to failed minor allocation),
disconnect is never called and we could end up with active URBs for an
unbound interface. This in turn could lead to deallocated memory being
dereferenced in the completion callbacks.
Fixes: ee467a1f20 ("USB: serial: add Moxa UPORT 12XX/14XX/16XX
driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a377f9e906 upstream.
A bug in the CRTSCTS handling caused RTS to alternate between
CRTSCTS=0 => "RTS is transmit active signal" and
CRTSCTS=1 => "RTS is used for receive flow control"
instead of
CRTSCTS=0 => "RTS is statically active" and
CRTSCTS=1 => "RTS is used for receive flow control"
This only happened after first having enabled CRTSCTS.
Signed-off-by: Konstantin Shkolnyy <konstantin.shkolnyy@gmail.com>
Fixes: 39a66b8d22 ("[PATCH] USB: CP2101 Add support for flow control")
[johan: reword commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bc46b45a42 upstream.
Ensure that mei_cl_read_start is called under the device lock
also in the bus layer. The function updates global ctrl_wr_list
which should be locked.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9d04ee11db upstream.
When a message is received and amthif client is not in reading state
the message is ignored and left dangling in the queue. This may happen
after one of the amthif host connections is closed w/o completing the
reading. Another client will pick up a wrong message on next read
attempt which will lead to link reset.
To prevent this the driver has to properly discard the message when
amthif client is not in reading state.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6a8d648c8d upstream.
In the case when disconnection is initiated from the FW
the driver is flushing items from the write control list while
iterating over it:
mei_irq_write_handler()
list_for_each_entry_safe(ctrl_wr_list) <-- outer loop
mei_cl_irq_disconnect_rsp()
mei_cl_set_disconnected()
mei_io_list_flush(ctrl_wr_list) <-- destorying list
We move the list flushing to the completion routine.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c7c999cb18 upstream.
hci_vhci driver creates a hci device object dynamically upon each
HCI_VENDOR_PKT write. Although it checks the already created object
and returns an error, it's still racy and may build multiple hci_dev
objects concurrently when parallel writes are performed, as the device
tracks only a single hci_dev object.
This patch introduces a mutex to protect against the concurrent device
creations.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 373a32c848 upstream.
Both vhci_get_user and vhci_release race with open_timeout work. They
both contain cancel_delayed_work_sync, but do not test whether the
work actually created hdev or not. Since the work can be in progress
and _sync will wait for finishing it, we can have data->hdev allocated
when cancel_delayed_work_sync returns. But the call sites do 'if
(data->hdev)' *before* cancel_delayed_work_sync.
As a result:
* vhci_get_user allocates a second hdev and puts it into
data->hdev. The former is leaked.
* vhci_release does not release data->hdev properly as it thinks there
is none.
Fix both cases by moving the actual test *after* the call to
cancel_delayed_work_sync.
This can be hit by this program:
#include <err.h>
#include <fcntl.h>
#include <stdio.h>
#include <stdlib.h>
#include <time.h>
#include <unistd.h>
#include <sys/stat.h>
#include <sys/types.h>
int main(int argc, char **argv)
{
int fd;
srand(time(NULL));
while (1) {
const int delta = (rand() % 200 - 100) * 100;
fd = open("/dev/vhci", O_RDWR);
if (fd < 0)
err(1, "open");
usleep(1000000 + delta);
close(fd);
}
return 0;
}
And the result is:
BUG: KASAN: use-after-free in skb_queue_tail+0x13e/0x150 at addr ffff88006b0c1228
Read of size 8 by task kworker/u13:1/32068
=============================================================================
BUG kmalloc-192 (Tainted: G E ): kasan: bad access detected
-----------------------------------------------------------------------------
Disabling lock debugging due to kernel taint
INFO: Allocated in vhci_open+0x50/0x330 [hci_vhci] age=260 cpu=3 pid=32040
...
kmem_cache_alloc_trace+0x150/0x190
vhci_open+0x50/0x330 [hci_vhci]
misc_open+0x35b/0x4e0
chrdev_open+0x23b/0x510
...
INFO: Freed in vhci_release+0xa4/0xd0 [hci_vhci] age=9 cpu=2 pid=32040
...
__slab_free+0x204/0x310
vhci_release+0xa4/0xd0 [hci_vhci]
...
INFO: Slab 0xffffea0001ac3000 objects=16 used=13 fp=0xffff88006b0c1e00 flags=0x5fffff80004080
INFO: Object 0xffff88006b0c1200 @offset=4608 fp=0xffff88006b0c0600
Bytes b4 ffff88006b0c11f0: 09 df 00 00 01 00 00 00 00 00 00 00 00 00 00 00 ................
Object ffff88006b0c1200: 00 06 0c 6b 00 88 ff ff 00 00 00 00 00 00 00 00 ...k............
Object ffff88006b0c1210: 10 12 0c 6b 00 88 ff ff 10 12 0c 6b 00 88 ff ff ...k.......k....
Object ffff88006b0c1220: c0 46 c2 6b 00 88 ff ff c0 46 c2 6b 00 88 ff ff .F.k.....F.k....
Object ffff88006b0c1230: 01 00 00 00 01 00 00 00 e0 ff ff ff 0f 00 00 00 ................
Object ffff88006b0c1240: 40 12 0c 6b 00 88 ff ff 40 12 0c 6b 00 88 ff ff @..k....@..k....
Object ffff88006b0c1250: 50 0d 6e a0 ff ff ff ff 00 02 00 00 00 00 ad de P.n.............
Object ffff88006b0c1260: 00 00 00 00 00 00 00 00 ab 62 02 00 01 00 00 00 .........b......
Object ffff88006b0c1270: 90 b9 19 81 ff ff ff ff 38 12 0c 6b 00 88 ff ff ........8..k....
Object ffff88006b0c1280: 03 00 20 00 ff ff ff ff ff ff ff ff 00 00 00 00 .. .............
Object ffff88006b0c1290: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
Object ffff88006b0c12a0: 00 00 00 00 00 00 00 00 00 80 cd 3d 00 88 ff ff ...........=....
Object ffff88006b0c12b0: 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 . ..............
Redzone ffff88006b0c12c0: bb bb bb bb bb bb bb bb ........
Padding ffff88006b0c13f8: 00 00 00 00 00 00 00 00 ........
CPU: 3 PID: 32068 Comm: kworker/u13:1 Tainted: G B E 4.4.6-0-default #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.8.1-0-g4adadbd-20151112_172657-sheep25 04/01/2014
Workqueue: hci0 hci_cmd_work [bluetooth]
00000000ffffffff ffffffff81926cfa ffff88006be37c68 ffff88006bc27180
ffff88006b0c1200 ffff88006b0c1234 ffffffff81577993 ffffffff82489320
ffff88006bc24240 0000000000000046 ffff88006a100000 000000026e51eb80
Call Trace:
...
[<ffffffff81ec8ebe>] ? skb_queue_tail+0x13e/0x150
[<ffffffffa06e027c>] ? vhci_send_frame+0xac/0x100 [hci_vhci]
[<ffffffffa0c61268>] ? hci_send_frame+0x188/0x320 [bluetooth]
[<ffffffffa0c61515>] ? hci_cmd_work+0x115/0x310 [bluetooth]
[<ffffffff811a1375>] ? process_one_work+0x815/0x1340
[<ffffffff811a1f85>] ? worker_thread+0xe5/0x11f0
[<ffffffff811a1ea0>] ? process_one_work+0x1340/0x1340
[<ffffffff811b3c68>] ? kthread+0x1c8/0x230
...
Memory state around the buggy address:
ffff88006b0c1100: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff88006b0c1180: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff88006b0c1200: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff88006b0c1280: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
ffff88006b0c1300: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
Fixes: 23424c0d31 (Bluetooth: Add support creating virtual AMP controllers)
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 32ecd320db upstream.
008GE0 Toshiba mmc in some Intel Baytrail tablets responds to
MMC_SEND_EXT_CSD in 450-600ms.
This patch will...
() Increase the long read time quirk timeout from 300ms to 600ms. Original
author of that quirk says 300ms was only a guess and that the number
may need to be raised in the future.
() Add this specific MMC to the quirk
Signed-off-by: Matt Gumbel <matthew.k.gumbel@intel.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 30c9bb0d76 upstream.
The order of the _OSI related functionalities is as follows:
acpi_blacklisted()
acpi_dmi_osi_linux()
acpi_osi_setup()
acpi_osi_setup()
acpi_update_interfaces() if "!*"
<<<<<<<<<<<<<<<<<<<<<<<<
parse_args()
__setup("acpi_osi=")
acpi_osi_setup_linux()
acpi_update_interfaces() if "!*"
<<<<<<<<<<<<<<<<<<<<<<<<
acpi_early_init()
acpi_initialize_subsystem()
acpi_ut_initialize_interfaces()
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
acpi_bus_init()
acpi_os_initialize1()
acpi_install_interface_handler(acpi_osi_handler)
acpi_osi_setup_late()
acpi_update_interfaces() for "!"
>>>>>>>>>>>>>>>>>>>>>>>>
acpi_osi_handler()
Since acpi_osi_setup_linux() can override acpi_dmi_osi_linux(), the command
line setting can override the DMI detection. That's why acpi_blacklisted()
is put before __setup("acpi_osi=").
Then we can notice the following wrong invocation order. There are
acpi_update_interfaces() (marked by <<<<) calls invoked before
acpi_ut_initialize_interfaces() (marked by ^^^^). This makes it impossible
to use acpi_osi=!* correctly from OSI DMI table or from the command line.
The use of acpi_osi=!* is meant to disable both ACPICA
(acpi_gbl_supported_interfaces) and Linux specific strings
(osi_setup_entries) while the ACPICA part should have stopped working
because of the order issue.
This patch fixes this issue by moving acpi_update_interfaces() to where
it is invoked for acpi_osi=! (marked by >>>>) as this is ensured to be
invoked after acpi_ut_initialize_interfaces() (marked by ^^^^). Linux
specific strings are still handled in the original place in order to make
the following command line working: acpi_osi=!* acpi_osi="Module Device".
Note that since acpi_osi=!* is meant to further disable linux specific
string comparing to the acpi_osi=!, there is no such use case in our bug
fixing work and hence there is no one using acpi_osi=!* either from the
command line or from the DMI quirks, this issue is just a theoretical
issue.
Fixes: 741d81280a (ACPI: Add facility to remove all _OSI strings)
Tested-by: Lukas Wunner <lukas@wunner.de>
Tested-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c447116d0 upstream.
Some eMMCs set the partition switch timeout too low.
Now typically eMMCs are considered a critical component (e.g. because
they store the root file system) and consequently are expected to be
reliable. Thus we can neglect the use case where eMMCs can't switch
reliably and we might want a lower timeout to facilitate speedy
recovery.
Although we could employ a quirk for the cards that are affected (if
we could identify them all), as described above, there is little
benefit to having a low timeout, so instead simply set a minimum
timeout.
The minimum is set to 300ms somewhat arbitrarily - the examples that
have been seen had a timeout of 10ms but were sometimes taking 60-70ms.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb208f144c upstream.
As described in 'can: m_can: tag current CAN FD controllers as non-ISO'
(6cfda7fbeb) it is possible to define fixed configuration options by
setting the according bit in 'ctrlmode' and clear it in 'ctrlmode_supported'.
This leads to the incovenience that the fixed configuration bits can not be
passed by netlink even when they have the correct values (e.g. non-ISO, FD).
This patch fixes that issue and not only allows fixed set bit values to be set
again but now requires(!) to provide these fixed values at configuration time.
A valid CAN FD configuration consists of a nominal/arbitration bittiming, a
data bittiming and a control mode with CAN_CTRLMODE_FD set - which is now
enforced by a new can_validate() function. This fix additionally removed the
inconsistency that was prohibiting the support of 'CANFD-only' controller
drivers, like the RCar CAN FD.
For this reason a new helper can_set_static_ctrlmode() has been introduced to
provide a proper interface to handle static enabled CAN controller options.
Reported-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Reviewed-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b58afe6d6d upstream.
Fix static checker warning:
drivers/nfc/st21nfca/i2c.c:530 st21nfca_hci_i2c_acpi_request_resources()
error: 'gpiod_ena' dereferencing possible ERR_PTR()
Fix so that if no enable gpio can be retrieved an -ENODEV is returned.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: dfa8070d7f ("nfc: st21nfca: Add support for acpi probing for i2c device.")
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c9b973061 upstream.
The GICv3 driver wrongly assumes that it runs on the non-secure
side of a secure-enabled system, while it could be on a system
with a single security state, or a GICv3 with GICD_CTLR.DS set.
Either way, it is important to configure this properly, or
interrupts will simply not be delivered on this HW.
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f86c4fbd93 upstream.
When an IPI is generated by a CPU, the pattern looks roughly like:
<write shared data>
smp_wmb();
<write to GIC to signal SGI>
On the receiving CPU we rely on the fact that, once we've taken the
interrupt, then the freshly written shared data must be visible to us.
Put another way, the CPU isn't going to speculate taking an interrupt.
Unfortunately, this assumption turns out to be broken.
Consider that CPUx wants to send an IPI to CPUy, which will cause CPUy
to read some shared_data. Before CPUx has done anything, a random
peripheral raises an IRQ to the GIC and the IRQ line on CPUy is raised.
CPUy then takes the IRQ and starts executing the entry code, heading
towards gic_handle_irq. Furthermore, let's assume that a bunch of the
previous interrupts handled by CPUy were SGIs, so the branch predictor
kicks in and speculates that irqnr will be <16 and we're likely to
head into handle_IPI. The prefetcher then grabs a speculative copy of
shared_data which contains a stale value.
Meanwhile, CPUx gets round to updating shared_data and asking the GIC
to send an SGI to CPUy. Internally, the GIC decides that the SGI is
more important than the peripheral interrupt (which hasn't yet been
ACKed) but doesn't need to do anything to CPUy, because the IRQ line
is already raised.
CPUy then reads the ACK register on the GIC, sees the SGI value which
confirms the branch prediction and we end up with a stale shared_data
value.
This patch fixes the problem by adding an smp_rmb() to the IPI entry
code in gic_handle_irq. As it turns out, the combination of a control
dependency and an ISB instruction from the EOI in the GICv3 driver is
enough to provide the ordering we need, so we add a comment there
justifying the absence of an explicit smp_rmb().
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f49cf3b8b4 upstream.
Pwm config may sleep so defer it using a worker.
On a Freescale i.MX53 based board we ran into "BUG: scheduling while
atomic" because input_inject_event locks interrupts, but
imx_pwm_config_v2 sleeps.
Tested on Freescale i.MX53 SoC with 4.6.0.
Signed-off-by: Manfred Schlaegl <manfred.schlaegl@gmx.at>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 20878232c5 upstream.
Systems show a minimal load average of 0.00, 0.01, 0.05 even when they
have no load at all.
Uptime and /proc/loadavg on all systems with kernels released during the
last five years up until kernel version 4.6-rc5, show a 5- and 15-minute
minimum loadavg of 0.01 and 0.05 respectively. This should be 0.00 on
idle systems, but the way the kernel calculates this value prevents it
from getting lower than the mentioned values.
Likewise but not as obviously noticeable, a fully loaded system with no
processes waiting, shows a maximum 1/5/15 loadavg of 1.00, 0.99, 0.95
(multiplied by number of cores).
Once the (old) load becomes 93 or higher, it mathematically can never
get lower than 93, even when the active (load) remains 0 forever.
This results in the strange 0.00, 0.01, 0.05 uptime values on idle
systems. Note: 93/2048 = 0.0454..., which rounds up to 0.05.
It is not correct to add a 0.5 rounding (=1024/2048) here, since the
result from this function is fed back into the next iteration again,
so the result of that +0.5 rounding value then gets multiplied by
(2048-2037), and then rounded again, so there is a virtual "ghost"
load created, next to the old and active load terms.
By changing the way the internally kept value is rounded, that internal
value equivalent now can reach 0.00 on idle, and 1.00 on full load. Upon
increasing load, the internally kept load value is rounded up, when the
load is decreasing, the load value is rounded down.
The modified code was tested on nohz=off and nohz kernels. It was tested
on vanilla kernel 4.6-rc5 and on centos 7.1 kernel 3.10.0-327. It was
tested on single, dual, and octal cores system. It was tested on virtual
hosts and bare hardware. No unwanted effects have been observed, and the
problems that the patch intended to fix were indeed gone.
Tested-by: Damien Wyart <damien.wyart@free.fr>
Signed-off-by: Vik Heyndrickx <vik.heyndrickx@veribox.net>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Doug Smythies <dsmythies@telus.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 0f004f5a69 ("sched: Cure more NO_HZ load average woes")
Link: http://lkml.kernel.org/r/e8d32bff-d544-7748-72b5-3c86cc71f09f@veribox.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5a7aef1ef upstream.
This patch allows fscrypto to handle a second key prefix given by filesystem.
The main reason is to provide backward compatibility, since previously f2fs
used "f2fs:" as a crypto prefix instead of "fscrypt:".
Later, ext4 should also provide key_prefix() to give "ext4:".
One concern decribed by Ted would be kinda double check overhead of prefixes.
In x86, for example, validate_user_key consumes 8 ms after boot-up, which turns
out derive_key_aes() consumed most of the time to load specific crypto module.
After such the cold miss, it shows almost zero latencies, which treats as a
negligible overhead.
Note that request_key() detects wrong prefix in prior to derive_key_aes() even.
Cc: Ted Tso <tytso@mit.edu>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a6b27b79d upstream.
Megha Dey reported a kernel panic in crypto code. The problem is that
sha1_x8_avx2() clobbers registers r12-r15 without saving and restoring
them.
Before commit aec4d0e301 ("x86/asm/crypto: Simplify stack usage in
sha-mb functions"), those registers were saved and restored by the
callers of the function. I removed them with that commit because I
didn't realize sha1_x8_avx2() clobbered them.
Fix the potential undefined behavior associated with clobbering the
registers and make the behavior less surprising by changing the
registers to be callee saved/restored to conform with the C function
call ABI.
Also, rdx (aka RSP_SAVE) doesn't need to be saved: I verified that none
of the callers rely on it being saved, and it's not a callee-saved
register in the C ABI.
Fixes: aec4d0e301 ("x86/asm/crypto: Simplify stack usage in sha-mb functions")
Reported-by: Megha Dey <megha.dey@linux.intel.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a0974aa1a upstream.
This patch adds the CLK_SET_RATE_PARENT flag for the crypto core and
ahb blocks. Without this flag, clk_set_rate can fail for certain
frequency requests.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Fixes: 3966fab8b6 ("clk: qcom: Add MSM8916 Global Clock Controller support")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bdb6cf9f6f upstream.
The current sun4i-ss driver could generate data corruption when ciphering/deciphering.
It occurs randomly on end of handled data.
No root cause have been found and the only way to remove it is to replace
all spin_lock_bh by their irq counterparts.
Fixes: 6298e94821 ("crypto: sunxi-ss - Add Allwinner Security System crypto accelerator")
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e930c765ca upstream.
caam_jr_alloc() used to return NULL if a JR device could not be
allocated for a session. In turn, every user of this function used
IS_ERR() function to verify if anything went wrong, which does NOT look
for NULL values. This made the kernel crash if the sanity check failed,
because the driver continued to think it had allocated a valid JR dev
instance to the session and at some point it tries to do a caam_jr_free()
on a NULL JR dev pointer.
This patch is a fix for this issue.
Signed-off-by: Catalin Vasile <cata.vasile@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 59643d1535 upstream.
If the size passed to ring_buffer_resize() is greater than MAX_LONG - BUF_PAGE_SIZE
then the DIV_ROUND_UP() will return zero.
Here's the details:
# echo 18014398509481980 > /sys/kernel/debug/tracing/buffer_size_kb
tracing_entries_write() processes this and converts kb to bytes.
18014398509481980 << 10 = 18446744073709547520
and this is passed to ring_buffer_resize() as unsigned long size.
size = DIV_ROUND_UP(size, BUF_PAGE_SIZE);
Where DIV_ROUND_UP(a, b) is (a + b - 1)/b
BUF_PAGE_SIZE is 4080 and here
18446744073709547520 + 4080 - 1 = 18446744073709551599
where 18446744073709551599 is still smaller than 2^64
2^64 - 18446744073709551599 = 17
But now 18446744073709551599 / 4080 = 4521260802379792
and size = size * 4080 = 18446744073709551360
This is checked to make sure its still greater than 2 * 4080,
which it is.
Then we convert to the number of buffer pages needed.
nr_page = DIV_ROUND_UP(size, BUF_PAGE_SIZE)
but this time size is 18446744073709551360 and
2^64 - (18446744073709551360 + 4080 - 1) = -3823
Thus it overflows and the resulting number is less than 4080, which makes
3823 / 4080 = 0
an nr_pages is set to this. As we already checked against the minimum that
nr_pages may be, this causes the logic to fail as well, and we crash the
kernel.
There's no reason to have the two DIV_ROUND_UP() (that's just result of
historical code changes), clean up the code and fix this bug.
Fixes: 83f40318da ("ring-buffer: Make removal of ring buffer pages atomic")
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b94a8fba5 upstream.
The size variable to change the ring buffer in ftrace is a long. The
nr_pages used to update the ring buffer based on the size is int. On 64 bit
machines this can cause an overflow problem.
For example, the following will cause the ring buffer to crash:
# cd /sys/kernel/debug/tracing
# echo 10 > buffer_size_kb
# echo 8556384240 > buffer_size_kb
Then you get the warning of:
WARNING: CPU: 1 PID: 318 at kernel/trace/ring_buffer.c:1527 rb_update_pages+0x22f/0x260
Which is:
RB_WARN_ON(cpu_buffer, nr_removed);
Note each ring buffer page holds 4080 bytes.
This is because:
1) 10 causes the ring buffer to have 3 pages.
(10kb requires 3 * 4080 pages to hold)
2) (2^31 / 2^10 + 1) * 4080 = 8556384240
The value written into buffer_size_kb is shifted by 10 and then passed
to ring_buffer_resize(). 8556384240 * 2^10 = 8761737461760
3) The size passed to ring_buffer_resize() is then divided by BUF_PAGE_SIZE
which is 4080. 8761737461760 / 4080 = 2147484672
4) nr_pages is subtracted from the current nr_pages (3) and we get:
2147484669. This value is saved in a signed integer nr_pages_to_update
5) 2147484669 is greater than 2^31 but smaller than 2^32, a signed int
turns into the value of -2147482627
6) As the value is a negative number, in update_pages_handler() it is
negated and passed to rb_remove_pages() and 2147482627 pages will
be removed, which is much larger than 3 and it causes the warning
because not all the pages asked to be removed were removed.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=118001
Fixes: 7a8e76a382 ("tracing: unified trace buffer")
Reported-by: Hao Qin <QEver.cn@gmail.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd9e2e5d3f upstream.
In testing with HiKey, we found that since
commit 3f30b158eb ("asix: On RX avoid creating bad Ethernet
frames"),
we're seeing lots of noise during network transfers:
[ 239.027993] asix 1-1.1:1.0 eth0: asix_rx_fixup() Data Header synchronisation was lost, remaining 988
[ 239.037310] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0x54ebb5ec, offset 4
[ 239.045519] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0xcdffe7a2, offset 4
[ 239.275044] asix 1-1.1:1.0 eth0: asix_rx_fixup() Data Header synchronisation was lost, remaining 988
[ 239.284355] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0x1d36f59d, offset 4
[ 239.292541] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0xaef3c1e9, offset 4
[ 239.518996] asix 1-1.1:1.0 eth0: asix_rx_fixup() Data Header synchronisation was lost, remaining 988
[ 239.528300] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0x2881912, offset 4
[ 239.536413] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0x5638f7e2, offset 4
And network throughput ends up being pretty bursty and slow with
a overall throughput of at best ~30kB/s (where as previously we
got 1.1MB/s with the slower USB1.1 "full speed" host).
We found the issue also was reproducible on a x86_64 system,
using a "high-speed" USB2.0 port but the throughput did not
measurably drop (possibly due to the scp transfer being cpu
bound on my slow test hardware).
After lots of debugging, I found the check added in the
problematic commit seems to be calculating the offset
incorrectly.
In the normal case, in the main loop of the function, we do:
(where offset is zero, or set to "offset += (copy_length + 1) &
0xfffe" in the previous loop)
rx->header = get_unaligned_le32(skb->data +
offset);
offset += sizeof(u32);
But the problematic patch calculates:
offset = ((rx->remaining + 1) & 0xfffe) + sizeof(u32);
rx->header = get_unaligned_le32(skb->data + offset);
Adding some debug logic to check those offset calculation used
to find rx->header, the one in problematic code is always too
large by sizeof(u32).
Thus, this patch removes the incorrect " + sizeof(u32)" addition
in the problematic calculation, and resolves the issue.
Cc: Dean Jenkins <Dean_Jenkins@mentor.com>
Cc: "David B. Robins" <linux@davidrobins.net>
Cc: Mark Craske <Mark_Craske@mentor.com>
Cc: Emil Goode <emilgoode@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: YongQin Liu <yongqin.liu@linaro.org>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Ivan Vecera <ivecera@redhat.com>
Cc: linux-usb@vger.kernel.org
Cc: netdev@vger.kernel.org
Reported-by: Yongqin Liu <yongqin.liu@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cfda35d982 upstream.
See [MS-NLMP] 3.2.5.1.2 Server Receives an AUTHENTICATE_MESSAGE from the Client:
...
Set NullSession to FALSE
If (AUTHENTICATE_MESSAGE.UserNameLen == 0 AND
AUTHENTICATE_MESSAGE.NtChallengeResponse.Length == 0 AND
(AUTHENTICATE_MESSAGE.LmChallengeResponse == Z(1)
OR
AUTHENTICATE_MESSAGE.LmChallengeResponse.Length == 0))
-- Special case: client requested anonymous authentication
Set NullSession to TRUE
...
Only server which map unknown users to guest will allow
access using a non-null NTChallengeResponse.
For Samba it's the "map to guest = bad user" option.
BUG: https://bugzilla.samba.org/show_bug.cgi?id=11913
Signed-off-by: Stefan Metzmacher <metze@samba.org>
Signed-off-by: Steve French <smfrench@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 897fba1172 upstream.
Wrong return code was being returned on SMB3 rmdir of
non-empty directory.
For SMB3 (unlike for cifs), we attempt to delete a directory by
set of delete on close flag on the open. Windows clients set
this flag via a set info (SET_FILE_DISPOSITION to set this flag)
which properly checks if the directory is empty.
With this patch on smb3 mounts we correctly return
"DIRECTORY NOT EMPTY"
on attempts to remove a non-empty directory.
Signed-off-by: Steve French <steve.french@primarydata.com>
Acked-by: Sachin Prabhu <sprabhu@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef3f00a4d3 upstream.
When booting with nr_cpus=1, uncore_pci_probe tries to init the PCI/uncore
also for the other packages and fails with warning when they are not found.
The warning is bogus because it's correct to fail here for packages which are
not initialized. Remove it and return silently.
Fixes: cf6d445f68 "perf/x86/uncore: Track packages, not per CPU data"
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: stable@vger.kernel.org
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e4fe9e7dc3 upstream.
The EC field of the constructed ESR is conditionally modified by ORing in
ESR_ELx_EC_DABT_LOW for a data abort. However, ESR_ELx_EC_SHIFT is missing
from this condition.
Signed-off-by: Matt Evans <matt.evans@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d4b9e0790a upstream.
The ARM architecture mandates that when changing a page table entry
from a valid entry to another valid entry, an invalid entry is first
written, TLB invalidated, and only then the new entry being written.
The current code doesn't respect this, directly writing the new
entry and only then invalidating TLBs. Let's fix it up.
Reported-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f228b494e5 upstream.
The loop that browses the array compat_hwcap_str will stop when a NULL
is encountered, however NULL is missing at the end of array. This will
lead to overrun until a NULL is found somewhere in the following memory.
In reality, this works out because the compat_hwcap2_str array tends to
follow immediately in memory, and that *is* terminated correctly.
Furthermore, the unsigned int compat_elf_hwcap is checked before
printing each capability, so we end up doing the right thing because
the size of the two arrays is less than 32. Still, this is an obvious
mistake and should be fixed.
Note for backporting: commit 12d11817ea ("arm64: Move
/proc/cpuinfo handling code") moved this code in v4.4. Prior to that
commit, the same change should be made in arch/arm64/kernel/setup.c.
Fixes: 44b82b7700 "arm64: Fix up /proc/cpuinfo"
Signed-off-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 282aa7051b upstream.
The update to the accessed or dirty states for block mappings must be
done atomically on hardware with support for automatic AF/DBM. The
ptep_set_access_flags() function has been fixed as part of commit
66dbd6e61a ("arm64: Implement ptep_set_access_flags() for hardware
AF/DBM"). This patch brings pmdp_set_access_flags() in line with the pte
counterpart.
Fixes: 2f4b829c62 ("arm64: Add support for hardware updates of the access and dirty pte bits")
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66dbd6e61a upstream.
When hardware updates of the access and dirty states are enabled, the
default ptep_set_access_flags() implementation based on calling
set_pte_at() directly is potentially racy. This triggers the "racy dirty
state clearing" warning in set_pte_at() because an existing writable PTE
is overridden with a clean entry.
There are two main scenarios for this situation:
1. The CPU getting an access fault does not support hardware updates of
the access/dirty flags. However, a different agent in the system
(e.g. SMMU) can do this, therefore overriding a writable entry with a
clean one could potentially lose the automatically updated dirty
status
2. A more complex situation is possible when all CPUs support hardware
AF/DBM:
a) Initial state: shareable + writable vma and pte_none(pte)
b) Read fault taken by two threads of the same process on different
CPUs
c) CPU0 takes the mmap_sem and proceeds to handling the fault. It
eventually reaches do_set_pte() which sets a writable + clean pte.
CPU0 releases the mmap_sem
d) CPU1 acquires the mmap_sem and proceeds to handle_pte_fault(). The
pte entry it reads is present, writable and clean and it continues
to pte_mkyoung()
e) CPU1 calls ptep_set_access_flags()
If between (d) and (e) the hardware (another CPU) updates the dirty
state (clears PTE_RDONLY), CPU1 will override the PTR_RDONLY bit
marking the entry clean again.
This patch implements an arm64-specific ptep_set_access_flags() function
to perform an atomic update of the PTE flags.
Fixes: 2f4b829c62 ("arm64: Add support for hardware updates of the access and dirty pte bits")
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Ming Lei <tom.leiming@gmail.com>
Tested-by: Julien Grall <julien.grall@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
[will: reworded comment]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5bb1cc0ff9 upstream.
Currently, pmd_present() only checks for a non-zero value, returning
true even after pmd_mknotpresent() (which only clears the type bits).
This patch converts pmd_present() to using pte_present(), similar to the
other pmd_*() checks. As a side effect, it will return true for
PROT_NONE mappings, though they are not yet used by the kernel with
transparent huge pages.
For consistency, also change pmd_mknotpresent() to only clear the
PMD_SECT_VALID bit, even though the PMD_TABLE_BIT is already 0 for block
mappings (no functional change). The unused PMD_SECT_PROT_NONE
definition is removed as transparent huge pages use the pte page prot
values.
Fixes: 9c7e535fcc ("arm64: mm: Route pmd thp functions through pte equivalents")
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 911f56eeb8 upstream.
With hardware AF/DBM support, pmd modifications (transparent huge pages)
should be performed atomically using load/store exclusive. The initial
patches defined the get-and-clear function and __HAVE_ARCH_* macro
without the "huge" word, leaving the pmdp_huge_get_and_clear() to the
default, non-atomic implementation.
Fixes: 2f4b829c62 ("arm64: Add support for hardware updates of the access and dirty pte bits")
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-06-01 12:17:57 -07:00
1315 changed files with 299996 additions and 6464 deletions
/* Provide backwards compatible aliases for the old sdhost dtparams. */
/{
compatible = "brcm,bcm2708";
fragment@0 {
target = <&sdhost>;
frag0: __overlay__ {
brcm,overclock-50 = <0>;
brcm,pio-limit = <1>;
brcm,debug-flags = <0>;
status = "okay";
};
};
fragment@1 {
target = <&mmc>;
__overlay__ {
status = "disabled";
};
};
__overrides__ {
overclock_50 = <&frag0>,"brcm,overclock-50:0";
force_pio = <&frag0>,"brcm,force-pio?";
pio_limit = <&frag0>,"brcm,pio-limit:0";
debug = <&frag0>,"brcm,debug?";
};
};
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
