The BCM2835 I2C blocks have a register to set the clock-stretch
timeout - how long the device is allowed to hold SCL low - in bus
cycles. The current driver doesn't write to the register, therefore
the default value of 64 cycles is being used for all devices.
Set the timeout to the value recommended for SMBus - 35ms.
See: https://github.com/raspberrypi/linux/issues/3064
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Seen on a VLI VL805 PCIe to USB controller. For non-stream endpoints
at least, if the xHC halts on a particular TRB due to an error then
the DCS field in the Out Endpoint Context maintained by the hardware
is not updated with the current cycle state.
Using the quirk XHCI_EP_CTX_BROKEN_DCS and instead fetch the DCS bit
from the TRB that the xHC stopped on.
See: https://github.com/raspberrypi/linux/issues/3060
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
pl011_tx_chars takes a "from_irq" parameter to reduce the number of
register accesses. When from_irq is true the function assumes that the
FIFO is half empty and writes up to half a FIFO's worth of bytes
without polling the FIFO status register, the reasoning being that
the function is being called as a result of the TX interrupt being
raised. This logic would work were it not for the fact that
pl011_rx_chars, called from pl011_int before pl011_tx_chars, releases
the spinlock before calling tty_flip_buffer_push.
A user thread writing to the UART claims the spinlock and ultimately
calls pl011_tx_chars with from_irq set to false. This reverts to the
older logic that polls the FIFO status register before sending every
byte. If this happen on an SMP system during the section of the IRQ
handler where the spinlock has been released, then by the time the TX
interrupt handler is called, the FIFO may already be full, and any
further writes are likely to be lost.
The fix involves adding a per-port flag that is true iff running from
within the interrupt handler and the spinlock has not yet been released.
This flag is then used as the value for the from_irq parameter of
pl011_tx_chars, causing polling to be used in the unsafe case.
Fixes: 1e84d22322 ("serial/amba-pl011: Refactor and simplify TX FIFO handling")
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
commit 3f93a4f297 upstream.
It is possible for an irq triggered by channel0 to be received later
after clks are disabled once firmware loaded during sdma probe. If
that happens then clearing them by writing to SDMA_H_INTR won't work
and the kernel will hang processing infinite interrupts. Actually,
don't need interrupt triggered on channel0 since it's pollling
SDMA_H_STATSTOP to know channel0 done rather than interrupt in
current code, just clear BD_INTR to disable channel0 interrupt to
avoid the above case.
This issue was brought by commit 1d069bfa3c ("dmaengine: imx-sdma:
ack channel 0 IRQ in the interrupt handler") which didn't take care
the above case.
Fixes: 1d069bfa3c ("dmaengine: imx-sdma: ack channel 0 IRQ in the interrupt handler")
Cc: stable@vger.kernel.org #5.0+
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Reported-by: Sven Van Asbroeck <thesven73@gmail.com>
Tested-by: Sven Van Asbroeck <thesven73@gmail.com>
Reviewed-by: Michael Olbrich <m.olbrich@pengutronix.de>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 637dfa0fad upstream.
scripts/package/builddeb calls "make dtbs_install" after executing
a plain make (i.e. no build targets specified). It will fail if dtbs
were not built beforehand. Match the arm64 architecture where DTBs get
built by the "all" target.
Signed-off-by: Cedric Hombourger <Cedric_Hombourger@mentor.com>
[paul.burton@mips.com: s/builddep/builddeb]
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: stable@vger.kernel.org # v4.1+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0b24cae4d5 upstream.
Add a missing EHB (Execution Hazard Barrier) in mtc0 -> mfc0 sequence.
Without this execution hazard barrier it's possible for the value read
back from the KScratch register to be the value from before the mtc0.
Reproducible on P5600 & P6600.
The hazard is documented in the MIPS Architecture Reference Manual Vol.
III: MIPS32/microMIPS32 Privileged Resource Architecture (MD00088), rev
6.03 table 8.1 which includes:
Producer | Consumer | Hazard
----------|----------|----------------------------
mtc0 | mfc0 | any coprocessor 0 register
Signed-off-by: Dmitry Korotin <dkorotin@wavecomp.com>
[paul.burton@mips.com:
- Commit message tweaks.
- Add Fixes tags.
- Mark for stable back to v3.15 where P5600 support was introduced.]
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: 3d8bfdd030 ("MIPS: Use C0_KScratch (if present) to hold PGD pointer.")
Fixes: 829dcc0a95 ("MIPS: Add MIPS P5600 probe support")
Cc: linux-mips@vger.kernel.org
Cc: stable@vger.kernel.org # v3.15+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1e091c3bbf upstream.
The DRC appears to be effectively empty after an RPC/RDMA transport
reconnect. The problem is that each connection uses a different
source port, which defeats the DRC hash.
Clients always have to disconnect before they send retransmissions
to reset the connection's credit accounting, thus every retransmit
on NFS/RDMA will miss the DRC.
An NFS/RDMA client's IP source port is meaningless for RDMA
transports. The transport layer typically sets the source port value
on the connection to a random ephemeral port. The server already
ignores it for the "secure port" check. See commit 16e4d93f6d
("NFSD: Ignore client's source port on RDMA transports").
The Linux NFS server's DRC resolves XID collisions from the same
source IP address by using the checksum of the first 200 bytes of
the RPC call header.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3b2d4dcf71 upstream.
Since commit 10a68cdf10 (nfsd: fix performance-limiting session
calculation) (Linux 5.1-rc1 and 4.19.31), shares from NFS servers with
1 TB of memory cannot be mounted anymore. The mount just hangs on the
client.
The gist of commit 10a68cdf10 is the change below.
-avail = clamp_t(int, avail, slotsize, avail/3);
+avail = clamp_t(int, avail, slotsize, total_avail/3);
Here are the macros.
#define min_t(type, x, y) __careful_cmp((type)(x), (type)(y), <)
#define clamp_t(type, val, lo, hi) min_t(type, max_t(type, val, lo), hi)
`total_avail` is 8,434,659,328 on the 1 TB machine. `clamp_t()` casts
the values to `int`, which for 32-bit integers can only hold values
−2,147,483,648 (−2^31) through 2,147,483,647 (2^31 − 1).
`avail` (in the function signature) is just 65536, so that no overflow
was happening. Before the commit the assignment would result in 21845,
and `num = 4`.
When using `total_avail`, it is causing the assignment to be
18446744072226137429 (printed as %lu), and `num` is then 4164608182.
My next guess is, that `nfsd_drc_mem_used` is then exceeded, and the
server thinks there is no memory available any more for this client.
Updating the arguments of `clamp_t()` and `min_t()` to `unsigned long`
fixes the issue.
Now, `avail = 65536` (before commit 10a68cdf10 `avail = 21845`), but
`num = 4` remains the same.
Fixes: c54f24e338 (nfsd: fix performance-limiting session calculation)
Cc: stable@vger.kernel.org
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb34e690e9 upstream.
Thomas reported that:
| Background:
|
| In preparation of supporting IPI shorthands I changed the CPU offline
| code to software disable the local APIC instead of just masking it.
| That's done by clearing the APIC_SPIV_APIC_ENABLED bit in the APIC_SPIV
| register.
|
| Failure:
|
| When the CPU comes back online the startup code triggers occasionally
| the warning in apic_pending_intr_clear(). That complains that the IRRs
| are not empty.
|
| The offending vector is the local APIC timer vector who's IRR bit is set
| and stays set.
|
| It took me quite some time to reproduce the issue locally, but now I can
| see what happens.
|
| It requires apicv_enabled=0, i.e. full apic emulation. With apicv_enabled=1
| (and hardware support) it behaves correctly.
|
| Here is the series of events:
|
| Guest CPU
|
| goes down
|
| native_cpu_disable()
|
| apic_soft_disable();
|
| play_dead()
|
| ....
|
| startup()
|
| if (apic_enabled())
| apic_pending_intr_clear() <- Not taken
|
| enable APIC
|
| apic_pending_intr_clear() <- Triggers warning because IRR is stale
|
| When this happens then the deadline timer or the regular APIC timer -
| happens with both, has fired shortly before the APIC is disabled, but the
| interrupt was not serviced because the guest CPU was in an interrupt
| disabled region at that point.
|
| The state of the timer vector ISR/IRR bits:
|
| ISR IRR
| before apic_soft_disable() 0 1
| after apic_soft_disable() 0 1
|
| On startup 0 1
|
| Now one would assume that the IRR is cleared after the INIT reset, but this
| happens only on CPU0.
|
| Why?
|
| Because our CPU0 hotplug is just for testing to make sure nothing breaks
| and goes through an NMI wakeup vehicle because INIT would send it through
| the boots-trap code which is not really working if that CPU was not
| physically unplugged.
|
| Now looking at a real world APIC the situation in that case is:
|
| ISR IRR
| before apic_soft_disable() 0 1
| after apic_soft_disable() 0 1
|
| On startup 0 0
|
| Why?
|
| Once the dying CPU reenables interrupts the pending interrupt gets
| delivered as a spurious interupt and then the state is clear.
|
| While that CPU0 hotplug test case is surely an esoteric issue, the APIC
| emulation is still wrong, Even if the play_dead() code would not enable
| interrupts then the pending IRR bit would turn into an ISR .. interrupt
| when the APIC is reenabled on startup.
From SDM 10.4.7.2 Local APIC State After It Has Been Software Disabled
* Pending interrupts in the IRR and ISR registers are held and require
masking or handling by the CPU.
In Thomas's testing, hardware cpu will not respect soft disable LAPIC
when IRR has already been set or APICv posted-interrupt is in flight,
so we can skip soft disable APIC checking when clearing IRR and set ISR,
continue to respect soft disable APIC when attempting to set IRR.
Reported-by: Rong Chen <rong.a.chen@intel.com>
Reported-by: Feng Tang <feng.tang@intel.com>
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rong Chen <rong.a.chen@intel.com>
Cc: Feng Tang <feng.tang@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8a3dca6325 ]
When fixing the skb leak introduced by the conversion to rbtree, I
forgot about the special case of duplicate fragments. The condition
under the 'insert_error' label isn't effective anymore as
nf_ct_frg6_gather() doesn't override the returned value anymore. So
duplicate fragments now get NF_DROP verdict.
To accept duplicate fragments again, handle them specially as soon as
inet_frag_queue_insert() reports them. Return -EINPROGRESS which will
translate to NF_STOLEN verdict, like any accepted fragment. However,
such packets don't carry any new information and aren't queued, so we
just drop them immediately.
Fixes: a0d56cb911 ("netfilter: ipv6: nf_defrag: fix leakage of unqueued fragments")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fdadd04931 ]
Michael and Sandipan report:
Commit ede95a63b5 introduced a bpf_jit_limit tuneable to limit BPF
JIT allocations. At compile time it defaults to PAGE_SIZE * 40000,
and is adjusted again at init time if MODULES_VADDR is defined.
For ppc64 kernels, MODULES_VADDR isn't defined, so we're stuck with
the compile-time default at boot-time, which is 0x9c400000 when
using 64K page size. This overflows the signed 32-bit bpf_jit_limit
value:
root@ubuntu:/tmp# cat /proc/sys/net/core/bpf_jit_limit
-1673527296
and can cause various unexpected failures throughout the network
stack. In one case `strace dhclient eth0` reported:
setsockopt(5, SOL_SOCKET, SO_ATTACH_FILTER, {len=11, filter=0x105dd27f8},
16) = -1 ENOTSUPP (Unknown error 524)
and similar failures can be seen with tools like tcpdump. This doesn't
always reproduce however, and I'm not sure why. The more consistent
failure I've seen is an Ubuntu 18.04 KVM guest booted on a POWER9
host would time out on systemd/netplan configuring a virtio-net NIC
with no noticeable errors in the logs.
Given this and also given that in near future some architectures like
arm64 will have a custom area for BPF JIT image allocations we should
get rid of the BPF_JIT_LIMIT_DEFAULT fallback / default entirely. For
4.21, we have an overridable bpf_jit_alloc_exec(), bpf_jit_free_exec()
so therefore add another overridable bpf_jit_alloc_exec_limit() helper
function which returns the possible size of the memory area for deriving
the default heuristic in bpf_jit_charge_init().
Like bpf_jit_alloc_exec() and bpf_jit_free_exec(), the new
bpf_jit_alloc_exec_limit() assumes that module_alloc() is the default
JIT memory provider, and therefore in case archs implement their custom
module_alloc() we use MODULES_{END,_VADDR} for limits and otherwise for
vmalloc_exec() cases like on ppc64 we use VMALLOC_{END,_START}.
Additionally, for archs supporting large page sizes, we should change
the sysctl to be handled as long to not run into sysctl restrictions
in future.
Fixes: ede95a63b5 ("bpf: add bpf_jit_limit knob to restrict unpriv allocations")
Reported-by: Sandipan Das <sandipan@linux.ibm.com>
Reported-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea401685a2 ]
Currently mskid is unsigned and hence comparisons with negative
error return values are always false. Fix this by making mskid an
int.
Fixes: f058e46855 ("net: hns: fix ICMP6 neighbor solicitation messages discard problem")
Addresses-Coverity: ("Operands don't affect result")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e00164a0f0 ]
err_spi is used when SERIAL_SC16IS7XX_SPI is enabled, so make
the label only available under SERIAL_SC16IS7XX_SPI option.
Otherwise, the below warning appears.
drivers/tty/serial/sc16is7xx.c:1523:1: warning: label ‘err_spi’ defined but not used [-Wunused-label]
err_spi:
^~~~~~~
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Fixes: ac0cdb3d99 ("sc16is7xx: missing unregister/delete driver on error in sc16is7xx_init()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a0d56cb911 ]
With commit 997dd96471 ("net: IP6 defrag: use rbtrees in
nf_conntrack_reasm.c"), nf_ct_frag6_reasm() is now called from
nf_ct_frag6_queue(). With this change, nf_ct_frag6_queue() can fail
after the skb has been added to the fragment queue and
nf_ct_frag6_gather() was adapted to handle this case.
But nf_ct_frag6_queue() can still fail before the fragment has been
queued. nf_ct_frag6_gather() can't handle this case anymore, because it
has no way to know if nf_ct_frag6_queue() queued the fragment before
failing. If it didn't, the skb is lost as the error code is overwritten
with -EINPROGRESS.
Fix this by setting -EINPROGRESS directly in nf_ct_frag6_queue(), so
that nf_ct_frag6_gather() can propagate the error as is.
Fixes: 997dd96471 ("net: IP6 defrag: use rbtrees in nf_conntrack_reasm.c")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 47d3d7fdb1 ]
Since ip6frag_expire_frag_queue() now pulls the head skb
from frag queue, we should no longer use skb_get(), since
this leads to an skb leak.
Stefan Bader initially reported a problem in 4.4.stable [1] caused
by the skb_get(), so this patch should also fix this issue.
296583.091021] kernel BUG at /build/linux-6VmqmP/linux-4.4.0/net/core/skbuff.c:1207!
[296583.091734] Call Trace:
[296583.091749] [<ffffffff81740e50>] __pskb_pull_tail+0x50/0x350
[296583.091764] [<ffffffff8183939a>] _decode_session6+0x26a/0x400
[296583.091779] [<ffffffff817ec719>] __xfrm_decode_session+0x39/0x50
[296583.091795] [<ffffffff818239d0>] icmpv6_route_lookup+0xf0/0x1c0
[296583.091809] [<ffffffff81824421>] icmp6_send+0x5e1/0x940
[296583.091823] [<ffffffff81753238>] ? __netif_receive_skb+0x18/0x60
[296583.091838] [<ffffffff817532b2>] ? netif_receive_skb_internal+0x32/0xa0
[296583.091858] [<ffffffffc0199f74>] ? ixgbe_clean_rx_irq+0x594/0xac0 [ixgbe]
[296583.091876] [<ffffffffc04eb260>] ? nf_ct_net_exit+0x50/0x50 [nf_defrag_ipv6]
[296583.091893] [<ffffffff8183d431>] icmpv6_send+0x21/0x30
[296583.091906] [<ffffffff8182b500>] ip6_expire_frag_queue+0xe0/0x120
[296583.091921] [<ffffffffc04eb27f>] nf_ct_frag6_expire+0x1f/0x30 [nf_defrag_ipv6]
[296583.091938] [<ffffffff810f3b57>] call_timer_fn+0x37/0x140
[296583.091951] [<ffffffffc04eb260>] ? nf_ct_net_exit+0x50/0x50 [nf_defrag_ipv6]
[296583.091968] [<ffffffff810f5464>] run_timer_softirq+0x234/0x330
[296583.091982] [<ffffffff8108a339>] __do_softirq+0x109/0x2b0
Fixes: d4289fcc9b ("net: IP6 defrag: use rbtrees for IPv6 defrag")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Stefan Bader <stefan.bader@canonical.com>
Cc: Peter Oskolkov <posk@google.com>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d84e7bc059 ]
>> net/rds/send.c:1109:42: warning: Using plain integer as NULL pointer
Fixes: ea010070d0 ("net/rds: fix warn in rds_message_alloc_sgs")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 183ab39eb0 ]
The recent commit 98081ca62c ("ALSA: hda - Record the current power
state before suspend/resume calls") made the HD-audio driver to store
the PM state in power_state field. This forgot, however, the
initialization at power up. Although the codec drivers usually don't
need to refer to this field in the normal operation, let's initialize
it properly for consistency.
Fixes: 98081ca62c ("ALSA: hda - Record the current power state before suspend/resume calls")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4d96e13ee9 ]
This patch fixes the missing device reference release-after-use in
the positive leg of the roce reset API of the HNS DSAF.
Fixes: c969c6e7ab ("net: hns: Fix object reference leaks in hns_dsaf_roce_reset()")
Reported-by: John Garry <john.garry@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15d55bae4e ]
A recent commit returns an error if icmp is used as the ip-proto for
IPv6 fib rules. Update fib_rule_tests to send ipv6-icmp instead of icmp.
Fixes: 5e1a99eae8 ("ipv4: Add ICMPv6 support when parse route ipproto")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2ffff085d ]
spin_lock_bh() is used in table_path_del() but rcu_read_unlock()
is used for unlocking. Fix it by using spin_unlock_bh() instead
of rcu_read_unlock() in the error handling case.
Fixes: b4c3fbe636 ("mac80211: Use linked list instead of rhashtable walk for mesh tables")
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c77bf7de1 ]
This fixes wrong access of address spaces of node and meta inodes after iput.
Fixes: 60aa4d5536 ("f2fs: fix use-after-free issue when accessing sbi->stat_info")
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e0d0a5fd3 ]
Virtual MFC codec's child devices must not be assigned to platform bus,
because they are allocated as raw 'struct device' and don't have the
corresponding 'platform' part. This fixes NULL pointer access revealed
recently by commit a66d972465 ("devres: Align data[] to
ARCH_KMALLOC_MINALIGN").
Fixes: c79667dd93 ("media: s5p-mfc: replace custom reserved memory handling code with generic one")
Reported-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f61bca58f6 ]
Commit <26d92e951fe0>
("net/smc: move unhash as early as possible in smc_release()")
fixes one occurrence in the smc code, but the same pattern exists
in other places. This patch covers the remaining occurrences and
makes sure, the unhash operation is done before the smc->clcsock is
released. This avoids a potential use-after-free in smc_diag_dump().
Reviewed-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e149113a74 ]
In commit 993107fea5 ("mlxsw: spectrum_switchdev: Fix VLAN device
deletion via ioctl") I fixed a bug caused by the fact that the driver
views differently the deletion of a VLAN device when it is deleted via
an ioctl and netlink.
Instead of relying on a specific order of events (device being
unregistered vs. VLAN filter being updated), simply make sure that the
driver performs the necessary cleanup when the VLAN device is unlinked,
which always happens before the other two events.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 423ea32554 ]
Make the forward declaration actually match the real function
definition, something that previous versions of gcc had just ignored.
This is another patch to fix new warnings from gcc-9 before I start the
merge window pulls. I don't want to miss legitimate new warnings just
because my system update brought a new compiler with new warnings.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit debd1c065d upstream.
Recent FITRIM work, namely bbbf7243d6 ("btrfs: combine device update
operations during transaction commit") combined the way certain
operations are recoded in a transaction. As a result an ASSERT was added
in dev_replace_finish to ensure the new code works correctly.
Unfortunately I got reports that it's possible to trigger the assert,
meaning that during a device replace it's possible to have an unfinished
chunk allocation on the source device.
This is supposed to be prevented by the fact that a transaction is
committed before finishing the replace oepration and alter acquiring the
chunk mutex. This is not sufficient since by the time the transaction is
committed and the chunk mutex acquired it's possible to allocate a chunk
depending on the workload being executed on the replaced device. This
bug has been present ever since device replace was introduced but there
was never code which checks for it.
The correct way to fix is to ensure that there is no pending device
modification operation when the chunk mutex is acquire and if there is
repeat transaction commit. Unfortunately it's not possible to just
exclude the source device from btrfs_fs_devices::dev_alloc_list since
this causes ENOSPC to be hit in transaction commit.
Fixing that in another way would need to add special cases to handle the
last writes and forbid new ones. The looped transaction fix is more
obvious, and can be easily backported. The runtime of dev-replace is
long so there's no noticeable delay caused by that.
Reported-by: David Sterba <dsterba@suse.com>
Fixes: 391cd9df81 ("Btrfs: fix unprotected alloc list insertion during the finishing procedure of replace")
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dffcac2cb8 upstream.
In production we have noticed hard lockups on large machines running
large jobs due to kswaps hoarding lru lock within isolate_lru_pages when
sc->reclaim_idx is 0 which is a small zone. The lru was couple hundred
GiBs and the condition (page_zonenum(page) > sc->reclaim_idx) in
isolate_lru_pages() was basically skipping GiBs of pages while holding
the LRU spinlock with interrupt disabled.
On further inspection, it seems like there are two issues:
(1) If kswapd on the return from balance_pgdat() could not sleep (i.e.
node is still unbalanced), the classzone_idx is unintentionally set
to 0 and the whole reclaim cycle of kswapd will try to reclaim only
the lowest and smallest zone while traversing the whole memory.
(2) Fundamentally isolate_lru_pages() is really bad when the
allocation has woken kswapd for a smaller zone on a very large machine
running very large jobs. It can hoard the LRU spinlock while skipping
over 100s of GiBs of pages.
This patch only fixes (1). (2) needs a more fundamental solution. To
fix (1), in the kswapd context, if pgdat->kswapd_classzone_idx is
invalid use the classzone_idx of the previous kswapd loop otherwise use
the one the waker has requested.
Link: http://lkml.kernel.org/r/20190701201847.251028-1-shakeelb@google.com
Fixes: e716f2eb24 ("mm, vmscan: prevent kswapd sleeping prematurely due to mismatched classzone_idx")
Signed-off-by: Shakeel Butt <shakeelb@google.com>
Reviewed-by: Yang Shi <yang.shi@linux.alibaba.com>
Acked-by: Mel Gorman <mgorman@techsingularity.net>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Hillf Danton <hdanton@sina.com>
Cc: Roman Gushchin <guro@fb.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d5b844a2cf upstream.
The commit 9f255b632b ("module: Fix livepatch/ftrace module text
permissions race") causes a possible deadlock between register_kprobe()
and ftrace_run_update_code() when ftrace is using stop_machine().
The existing dependency chain (in reverse order) is:
-> #1 (text_mutex){+.+.}:
validate_chain.isra.21+0xb32/0xd70
__lock_acquire+0x4b8/0x928
lock_acquire+0x102/0x230
__mutex_lock+0x88/0x908
mutex_lock_nested+0x32/0x40
register_kprobe+0x254/0x658
init_kprobes+0x11a/0x168
do_one_initcall+0x70/0x318
kernel_init_freeable+0x456/0x508
kernel_init+0x22/0x150
ret_from_fork+0x30/0x34
kernel_thread_starter+0x0/0xc
-> #0 (cpu_hotplug_lock.rw_sem){++++}:
check_prev_add+0x90c/0xde0
validate_chain.isra.21+0xb32/0xd70
__lock_acquire+0x4b8/0x928
lock_acquire+0x102/0x230
cpus_read_lock+0x62/0xd0
stop_machine+0x2e/0x60
arch_ftrace_update_code+0x2e/0x40
ftrace_run_update_code+0x40/0xa0
ftrace_startup+0xb2/0x168
register_ftrace_function+0x64/0x88
klp_patch_object+0x1a2/0x290
klp_enable_patch+0x554/0x980
do_one_initcall+0x70/0x318
do_init_module+0x6e/0x250
load_module+0x1782/0x1990
__s390x_sys_finit_module+0xaa/0xf0
system_call+0xd8/0x2d0
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(text_mutex);
lock(cpu_hotplug_lock.rw_sem);
lock(text_mutex);
lock(cpu_hotplug_lock.rw_sem);
It is similar problem that has been solved by the commit 2d1e38f566
("kprobes: Cure hotplug lock ordering issues"). Many locks are involved.
To be on the safe side, text_mutex must become a low level lock taken
after cpu_hotplug_lock.rw_sem.
This can't be achieved easily with the current ftrace design.
For example, arm calls set_all_modules_text_rw() already in
ftrace_arch_code_modify_prepare(), see arch/arm/kernel/ftrace.c.
This functions is called:
+ outside stop_machine() from ftrace_run_update_code()
+ without stop_machine() from ftrace_module_enable()
Fortunately, the problematic fix is needed only on x86_64. It is
the only architecture that calls set_all_modules_text_rw()
in ftrace path and supports livepatching at the same time.
Therefore it is enough to move text_mutex handling from the generic
kernel/trace/ftrace.c into arch/x86/kernel/ftrace.c:
ftrace_arch_code_modify_prepare()
ftrace_arch_code_modify_post_process()
This patch basically reverts the ftrace part of the problematic
commit 9f255b632b ("module: Fix livepatch/ftrace module
text permissions race"). And provides x86_64 specific-fix.
Some refactoring of the ftrace code will be needed when livepatching
is implemented for arm or nds32. These architectures call
set_all_modules_text_rw() and use stop_machine() at the same time.
Link: http://lkml.kernel.org/r/20190627081334.12793-1-pmladek@suse.com
Fixes: 9f255b632b ("module: Fix livepatch/ftrace module text permissions race")
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Reported-by: Miroslav Benes <mbenes@suse.cz>
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
[
As reviewed by Miroslav Benes <mbenes@suse.cz>, removed return value of
ftrace_run_update_code() as it is a void function.
]
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 78c68e8f5c upstream.
Notify drm core before sending pending events during crtc disable.
This fixes the first event after disable having an old stale timestamp
by having drm_crtc_vblank_off update the timestamp to now.
This was seen while debugging weston log message:
Warning: computed repaint delay is insane: -8212 msec
This occurred due to:
1. driver starts up
2. fbcon comes along and restores fbdev, enabling vblank
3. vblank_disable_fn fires via timer disabling vblank, keeping vblank
seq number and time set at current value
(some time later)
4. weston starts and does a modeset
5. atomic commit disables crtc while it does the modeset
6. ipu_crtc_atomic_disable sends vblank with old seq number and time
Fixes: a474478642 ("drm/imx: fix crtc vblank state regression")
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit be132e1375 upstream.
When something goes wrong in the GPU init after the cmdbuf suballocator
has been constructed, we fail to destroy it properly. This causes havok
later when the GPU is unbound due to a module unload or similar.
Fixes: e66774dd6f (drm/etnaviv: add cmdbuf suballocator)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f496a555d upstream.
When KASLR and KASAN are both enabled, we keep the modules where they
are, and randomize the placement of the kernel so it is within 2 GB
of the module region. The reason for this is that putting modules in
the vmalloc region (like we normally do when KASLR is enabled) is not
possible in this case, given that the entire vmalloc region is already
backed by KASAN zero shadow pages, and so allocating dedicated KASAN
shadow space as required by loaded modules is not possible.
The default module allocation window is set to [_etext - 128MB, _etext]
in kaslr.c, which is appropriate for KASLR kernels booted without a
seed or with 'nokaslr' on the command line. However, as it turns out,
it is not quite correct for the KASAN case, since it still intersects
the vmalloc region at the top, where attempts to allocate shadow pages
will collide with the KASAN zero shadow pages, causing a WARN() and all
kinds of other trouble. So cap the top end to MODULES_END explicitly
when running with KASAN.
Cc: <stable@vger.kernel.org> # 4.9+
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 503d90b306 upstream.
This adds 4 SND_PCI_QUIRK(...) lines for several barebone models of the ODM
Clevo. The model names are written in regex syntax to describe/match all clevo
models that are similar enough and use the same PCI SSID that this fixup works
for them.
Additionally the lines regarding SSID 0x96e1 and 0x97e1 didn't fix audio for the
all our Clevo notebooks using these SSIDs (models Clevo P960* and P970*) since
ALC1220_FIXP_CLEVO_PB51ED_PINS swapped pins that are not necesarry to be
swapped. This patch initiates ALC1220_FIXUP_CLEVO_P950 instead for these model
and fixes the audio.
Fixes: 80690a276f ("ALSA: hda/realtek - Add quirk for Tuxedo XC 1509")
Signed-off-by: Richard Sailer <rs@tuxedocomputers.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2acf5a3e6e upstream.
There are a couple of left shifts of unsigned 8 bit values that
first get promoted to signed ints and hence get sign extended
on the shift if the top bit of the 8 bit values are set. Fix
this by casting the 8 bit values to unsigned ints to stop the
unintentional sign extension.
Addresses-Coverity: ("Unintended sign extension")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3450121997 upstream.
LINE6 drivers allocate the buffers based on the value returned from
usb_maxpacket() calls. The manipulated device may return zero for
this, and this results in the kmalloc() with zero size (and it may
succeed) while the other part of the driver code writes the packet
data with the fixed size -- which eventually overwrites.
This patch adds a simple sanity check for the invalid buffer size for
avoiding that problem.
Reported-by: syzbot+219f00fb49874dcaea17@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7fbd1753b6 upstream.
In IEC 61883-6, 8 MIDI data streams are multiplexed into single
MIDI conformant data channel. The index of stream is calculated by
modulo 8 of the value of data block counter.
In fireworks, the value of data block counter in CIP header has a quirk
with firmware version v5.0.0, v5.7.3 and v5.8.0. This brings ALSA
IEC 61883-1/6 packet streaming engine to miss detection of MIDI
messages.
This commit fixes the miss detection to modify the value of data block
counter for the modulo calculation.
For maintainers, this bug exists since a commit 18f5ed365d ("ALSA:
fireworks/firewire-lib: add support for recent firmware quirk") in Linux
kernel v4.2. There're many changes since the commit. This fix can be
backported to Linux kernel v4.4 or later. I tagged a base commit to the
backport for your convenience.
Besides, my work for Linux kernel v5.3 brings heavy code refactoring and
some structure members are renamed in 'sound/firewire/amdtp-stream.h'.
The content of this patch brings conflict when merging -rc tree with
this patch and the latest tree. I request maintainers to solve the
conflict to replace 'tx_first_dbc' with 'ctx_data.tx.first_dbc'.
Fixes: df075feefb ("ALSA: firewire-lib: complete AM824 data block processing layer")
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c3ea60c231 upstream.
There are two occurrances of a call to snd_seq_oss_fill_addr where
the dest_client and dest_port arguments are in the wrong order. Fix
this by swapping them around.
Addresses-Coverity: ("Arguments in wrong order")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a0fad630e upstream.
cryptd_skcipher_free() fails to free the struct skcipher_instance
allocated in cryptd_create_skcipher(), leading to a memory leak. This
is detected by kmemleak on bootup on ARM64 platforms:
unreferenced object 0xffff80003377b180 (size 1024):
comm "cryptomgr_probe", pid 822, jiffies 4294894830 (age 52.760s)
backtrace:
kmem_cache_alloc_trace+0x270/0x2d0
cryptd_create+0x990/0x124c
cryptomgr_probe+0x5c/0x1e8
kthread+0x258/0x318
ret_from_fork+0x10/0x1c
Fixes: 4e0958d19b ("crypto: cryptd - Add support for skcipher")
Cc: <stable@vger.kernel.org>
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 21d4120ec6 upstream.
Michal Suchanek reported [1] that running the pcrypt_aead01 test from
LTP [2] in a loop and holding Ctrl-C causes a NULL dereference of
alg->cra_users.next in crypto_remove_spawns(), via crypto_del_alg().
The test repeatedly uses CRYPTO_MSG_NEWALG and CRYPTO_MSG_DELALG.
The crash occurs when the instance that CRYPTO_MSG_DELALG is trying to
unregister isn't a real registered algorithm, but rather is a "test
larval", which is a special "algorithm" added to the algorithms list
while the real algorithm is still being tested. Larvals don't have
initialized cra_users, so that causes the crash. Normally pcrypt_aead01
doesn't trigger this because CRYPTO_MSG_NEWALG waits for the algorithm
to be tested; however, CRYPTO_MSG_NEWALG returns early when interrupted.
Everything else in the "crypto user configuration" API has this same bug
too, i.e. it inappropriately allows operating on larval algorithms
(though it doesn't look like the other cases can cause a crash).
Fix this by making crypto_alg_match() exclude larval algorithms.
[1] https://lkml.kernel.org/r/20190625071624.27039-1-msuchanek@suse.de
[2] https://github.com/linux-test-project/ltp/blob/20190517/testcases/kernel/crypto/pcrypt_aead01.c
Reported-by: Michal Suchanek <msuchanek@suse.de>
Fixes: a38f7907b9 ("crypto: Add userspace configuration API")
Cc: <stable@vger.kernel.org> # v3.2+
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6994eefb00 upstream.
Fix two issues:
When called for PTRACE_TRACEME, ptrace_link() would obtain an RCU
reference to the parent's objective credentials, then give that pointer
to get_cred(). However, the object lifetime rules for things like
struct cred do not permit unconditionally turning an RCU reference into
a stable reference.
PTRACE_TRACEME records the parent's credentials as if the parent was
acting as the subject, but that's not the case. If a malicious
unprivileged child uses PTRACE_TRACEME and the parent is privileged, and
at a later point, the parent process becomes attacker-controlled
(because it drops privileges and calls execve()), the attacker ends up
with control over two processes with a privileged ptrace relationship,
which can be abused to ptrace a suid binary and obtain root privileges.
Fix both of these by always recording the credentials of the process
that is requesting the creation of the ptrace relationship:
current_cred() can't change under us, and current is the proper subject
for access control.
This change is theoretically userspace-visible, but I am not aware of
any code that it will actually break.
Fixes: 64b875f7ac ("ptrace: Capture the ptracer's creds not PT_PTRACE_CAP")
Signed-off-by: Jann Horn <jannh@google.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bc7b488b1d upstream.
While loading the DMC firmware we were double checking the headers made
sense, but in no place we checked that we were actually reading memory
we were supposed to. This could be wrong in case the firmware file is
truncated or malformed.
Before this patch:
# ls -l /lib/firmware/i915/icl_dmc_ver1_07.bin
-rw-r--r-- 1 root root 25716 Feb 1 12:26 icl_dmc_ver1_07.bin
# truncate -s 25700 /lib/firmware/i915/icl_dmc_ver1_07.bin
# modprobe i915
# dmesg| grep -i dmc
[drm:intel_csr_ucode_init [i915]] Loading i915/icl_dmc_ver1_07.bin
[drm] Finished loading DMC firmware i915/icl_dmc_ver1_07.bin (v1.7)
i.e. it loads random data. Now it fails like below:
[drm:intel_csr_ucode_init [i915]] Loading i915/icl_dmc_ver1_07.bin
[drm:csr_load_work_fn [i915]] *ERROR* Truncated DMC firmware, rejecting.
i915 0000:00:02.0: Failed to load DMC firmware i915/icl_dmc_ver1_07.bin. Disabling runtime power management.
i915 0000:00:02.0: DMC firmware homepage: https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git/tree/i915
Before reading any part of the firmware file, validate the input first.
Fixes: eb805623d8 ("drm/i915/skl: Add support to load SKL CSR firmware.")
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190605235535.17791-1-lucas.demarchi@intel.com
(cherry picked from commit bc7b488b1d)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
[ Lucas: backported to 4.9+ adjusting the context ]
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c04e32e911 ]
At least for ARM64 kernels compiled with the crosstoolchain from
Debian/stretch or with the toolchain from kernel.org the line number is
not decoded correctly by 'decode_stacktrace.sh':
$ echo "[ 136.513051] f1+0x0/0xc [kcrash]" | \
CROSS_COMPILE=/opt/gcc-8.1.0-nolibc/aarch64-linux/bin/aarch64-linux- \
./scripts/decode_stacktrace.sh /scratch/linux-arm64/vmlinux \
/scratch/linux-arm64 \
/nfs/debian/lib/modules/4.20.0-devel
[ 136.513051] f1 (/linux/drivers/staging/kcrash/kcrash.c:68) kcrash
If addr2line from the toolchain is used the decoded line number is correct:
[ 136.513051] f1 (/linux/drivers/staging/kcrash/kcrash.c:57) kcrash
Link: http://lkml.kernel.org/r/20190527083425.3763-1-manut@linutronix.de
Signed-off-by: Manuel Traut <manut@linutronix.de>
Acked-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d477f8c202 ]
In the case that a process is constrained by taskset(1) (i.e.
sched_setaffinity(2)) to a subset of available cpus, and all of those are
subsequently offlined, the scheduler will set tsk->cpus_allowed to
the current value of task_cs(tsk)->effective_cpus.
This is done via a call to do_set_cpus_allowed() in the context of
cpuset_cpus_allowed_fallback() made by the scheduler when this case is
detected. This is the only call made to cpuset_cpus_allowed_fallback()
in the latest mainline kernel.
However, this is not sane behavior.
I will demonstrate this on a system running the latest upstream kernel
with the following initial configuration:
# grep -i cpu /proc/$$/status
Cpus_allowed: ffffffff,fffffff
Cpus_allowed_list: 0-63
(Where cpus 32-63 are provided via smt.)
If we limit our current shell process to cpu2 only and then offline it
and reonline it:
# taskset -p 4 $$
pid 2272's current affinity mask: ffffffffffffffff
pid 2272's new affinity mask: 4
# echo off > /sys/devices/system/cpu/cpu2/online
# dmesg | tail -3
[ 2195.866089] process 2272 (bash) no longer affine to cpu2
[ 2195.872700] IRQ 114: no longer affine to CPU2
[ 2195.879128] smpboot: CPU 2 is now offline
# echo on > /sys/devices/system/cpu/cpu2/online
# dmesg | tail -1
[ 2617.043572] smpboot: Booting Node 0 Processor 2 APIC 0x4
We see that our current process now has an affinity mask containing
every cpu available on the system _except_ the one we originally
constrained it to:
# grep -i cpu /proc/$$/status
Cpus_allowed: ffffffff,fffffffb
Cpus_allowed_list: 0-1,3-63
This is not sane behavior, as the scheduler can now not only place the
process on previously forbidden cpus, it can't even schedule it on
the cpu it was originally constrained to!
Other cases result in even more exotic affinity masks. Take for instance
a process with an affinity mask containing only cpus provided by smt at
the moment that smt is toggled, in a configuration such as the following:
# taskset -p f000000000 $$
# grep -i cpu /proc/$$/status
Cpus_allowed: 000000f0,00000000
Cpus_allowed_list: 36-39
A double toggle of smt results in the following behavior:
# echo off > /sys/devices/system/cpu/smt/control
# echo on > /sys/devices/system/cpu/smt/control
# grep -i cpus /proc/$$/status
Cpus_allowed: ffffff00,ffffffff
Cpus_allowed_list: 0-31,40-63
This is even less sane than the previous case, as the new affinity mask
excludes all smt-provided cpus with ids less than those that were
previously in the affinity mask, as well as those that were actually in
the mask.
With this patch applied, both of these cases end in the following state:
# grep -i cpu /proc/$$/status
Cpus_allowed: ffffffff,ffffffff
Cpus_allowed_list: 0-63
The original policy is discarded. Though not ideal, it is the simplest way
to restore sanity to this fallback case without reinventing the cpuset
wheel that rolls down the kernel just fine in cgroup v2. A user who wishes
for the previous affinity mask to be restored in this fallback case can use
that mechanism instead.
This patch modifies scheduler behavior by instead resetting the mask to
task_cs(tsk)->cpus_allowed by default, and cpu_possible mask in legacy
mode. I tested the cases above on both modes.
Note that the scheduler uses this fallback mechanism if and only if
_every_ other valid avenue has been traveled, and it is the last resort
before calling BUG().
Suggested-by: Waiman Long <longman@redhat.com>
Suggested-by: Phil Auld <pauld@redhat.com>
Signed-off-by: Joel Savitz <jsavitz@redhat.com>
Acked-by: Phil Auld <pauld@redhat.com>
Acked-by: Waiman Long <longman@redhat.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a0cac264a8 ]
The devm_gpiod_request_gpiod() call will add "-gpios" to
any passed connection ID before looking it up.
I do not think the reset GPIO on this platform is named
"reset-gpios-gpios" but rather "reset-gpios" in the device
tree, so fix this up so that we get a proper reset GPIO
handle.
Also drop the inclusion of the legacy GPIO header.
Fixes: 0e8ce93bdc ("i2c: pca-platform: add devicetree awareness")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb1921b17a ]
When a switch event, such as tablet mode/laptop mode or docked/undocked,
wakes a device make sure that the value of the swich is reported.
Without when a device is put in tablet mode from laptop mode when it is
suspended or vice versa the device will wake up but mode will be
incorrect.
Tested by suspending a device in laptop mode and putting it in tablet
mode, the device resumes and is in tablet mode. When suspending the
device in tablet mode and putting it in laptop mode the device resumes
and is in laptop mode.
Signed-off-by: Mathew King <mathewk@chromium.org>
Reviewed-by: Jett Rink <jettrink@chromium.org>
Reviewed-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 401fee8195 ]
Commit 78f3ac76d9 ("platform/x86: asus-wmi: Tell the EC the OS will
handle the display off hotkey") causes the backlight to be permanently off
on various EeePC laptop models using the eeepc-wmi driver (Asus EeePC
1015BX, Asus EeePC 1025C).
The asus_wmi_set_devstate(ASUS_WMI_DEVID_BACKLIGHT, 2, NULL) call added
by that commit is made conditional in this commit and only enabled in
the quirk_entry structs in the asus-nb-wmi driver fixing the broken
display / backlight on various EeePC laptop models.
Cc: João Paulo Rechi Vita <jprvita@endlessm.com>
Fixes: 78f3ac76d9 ("platform/x86: asus-wmi: Tell the EC the OS will handle the display off hotkey")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04268bf275 ]
When we call snd_soc_component_set_jack(component, NULL, NULL) we should
set rt274->jack to passed jack, so when interrupt is triggered it calls
snd_soc_jack_report(rt274->jack, ...) with proper value.
This fixes problem in machine where in register, we call
snd_soc_register(component, &headset, NULL), which just calls
rt274_mic_detect via callback.
Now when machine driver is removed "headset" will be gone, so we
need to tell codec driver that it's gone with:
snd_soc_register(component, NULL, NULL), but we also need to be able
to handle NULL jack argument here gracefully.
If we don't set it to NULL, next time the rt274_irq runs it will call
snd_soc_jack_report with first argument being invalid pointer and there
will be Oops.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d647b736a ]
During the integration of HDaudio support, we changed the way in which
we get hdev in snd_hdac_ext_bus_device_init() to use one preallocated
with devm_kzalloc(), however it still left kfree(hdev) in
snd_hdac_ext_bus_device_exit(). It leads to oopses when trying to
rmmod and modprobe. Fix it, by just removing kfree call.
SOF also uses some of the snd_hdac_ functions for HDAudio support but
allocated the memory with kzalloc. A matching fix is provided
separately to align all users of the snd_hdac_ library.
Fixes: 6298542fa3 ("ALSA: hdac: remove memory allocation from snd_hdac_ext_bus_device_init")
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fbc318afad ]
Gadget drivers may queue request in interrupt context. This would lead to
a descriptor allocation in that context. In that case we would hit
BUG_ON(in_interrupt()) in __get_vm_area_node.
Also remove the unnecessary cast.
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Tested-by: James Grant <jamesg@zaltys.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62fd0e0a24 ]
There is no deallocation of fusb300->ep[i] elements, allocated at
fusb300_probe.
The patch adds deallocation of fusb300->ep array elements.
Signed-off-by: Young Xiao <92siuyang@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9927000cb ]
Whilst testing the capture functionality of the i2s on the newer
SoCs it was noticed that the recording was somewhat distorted.
This was due to the offset not being set correctly on the receiver
side.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5628c89796 ]
The supported formats are S16_LE and S24_LE now. However, by datasheet
of max98090, S24_LE is only supported when it is in the right justified
mode. We should remove 24-bit format if it is not in that mode to avoid
triggering error.
Signed-off-by: Yu-Hsuan Hsu <yuhsuan@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2458d9d6d9 ]
mtk_dsi_stop() should be called after mtk_drm_crtc_atomic_disable(), which
needs ovl irq for drm_crtc_wait_one_vblank(), since after mtk_dsi_stop() is
called, ovl irq will be disabled. If drm_crtc_wait_one_vblank() is called
after last irq, it will timeout with this message: "vblank wait timed out
on crtc 0". This happens sometimes when turning off the screen.
In drm_atomic_helper.c#disable_outputs(),
the calling sequence when turning off the screen is:
1. mtk_dsi_encoder_disable()
--> mtk_output_dsi_disable()
--> mtk_dsi_stop(); /* sometimes make vblank timeout in
atomic_disable */
--> mtk_dsi_poweroff();
2. mtk_drm_crtc_atomic_disable()
--> drm_crtc_wait_one_vblank();
...
--> mtk_dsi_ddp_stop()
--> mtk_dsi_poweroff();
mtk_dsi_poweroff() has reference count design, change to make
mtk_dsi_stop() called in mtk_dsi_poweroff() when refcount is 0.
Fixes: 0707632b5b ("drm/mediatek: update DSI sub driver flow for sending commands to panel")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a4cd1d2b01 ]
num_pipes is used for mutex created in mtk_drm_crtc_create(). If we
don't clear num_pipes count, when rebinding driver, the count will
be accumulated. From mtk_disp_mutex_get(), there can only be at most
10 mutex id. Clear this number so it starts from 0 in every rebind.
Fixes: 119f517362 ("drm/mediatek: Add DRM Driver for Mediatek SoC MT8173.")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f0fd848342 ]
Unbinding components (i.e. mtk_dsi and mtk_disp_ovl/rdma/color) will
trigger master(mtk_drm)'s .unbind(), and currently mtk_drm's unbind
won't actually unbind components. During the next bind,
mtk_drm_kms_init() is called, and the components are added back.
.unbind() should call mtk_drm_kms_deinit() to unbind components.
And since component_master_del() in .remove() will trigger .unbind(),
which will also unregister device, it's fine to remove original functions
called here.
Fixes: 119f517362 ("drm/mediatek: Add DRM Driver for Mediatek SoC MT8173.")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8fd7a37b19 ]
detatch panel in mtk_dsi_destroy_conn_enc(), since .bind will try to
attach it again.
Fixes: 2e54c14e31 ("drm/mediatek: Add DSI sub driver")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 176a11834b ]
snd_soc_component_update_bits() may return 1 if operation
was successful and the value of the register changed.
Return a non-zero in ak4458_rstn_control for an error only.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Viorel Suman <viorel.suman@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5087a8f17d ]
If playback/capture is paused and system enters S3, after system returns
from suspend, BE dai needs to call prepare() callback when playback/capture
is released from pause if RESUME_INFO flag is not set.
Currently, the dpcm_be_dai_prepare() function will block calling prepare()
if the pcm is in SND_SOC_DPCM_STATE_PAUSED state. This will cause the
following test case fail if the pcm uses BE:
playback -> pause -> S3 suspend -> S3 resume -> pause release
The playback may exit abnormally when pause is released because the BE dai
prepare() is not called.
This patch allows dpcm_be_dai_prepare() to call dai prepare() callback in
SND_SOC_DPCM_STATE_PAUSED state.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a8dee20d79 ]
AK4458 is probed successfully even if AK4458 is not present - this
is caused by probe function returning no error on i2c access failure.
Return an error on probe if i2c access has failed.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Viorel Suman <viorel.suman@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3df05c805 ]
The cs4265_readable_register function stopped short of the maximum
register.
An example bug is taken from :
https://github.com/Audio-Injector/Ultra/issues/25
Where alsactl store fails with :
Cannot read control '2,0,0,C Data Buffer,0': Input/output error
This patch fixes the bug by setting the cs4265 to have readable
registers up to the maximum hardware register CS4265_MAX_REGISTER.
Signed-off-by: Matt Flax <flatmax@flatmax.org>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 91a9048f23 upstream.
We can't deal with tcp sequence number rewrite in flow_offload.
While at it, simplify helper check, we only need to know if the extension
is present, we don't need the helper data.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8437a6209f upstream.
Without it, whenever a packet has to be pushed up the stack (e.g. because
of mtu mismatch), then conntrack will flag packets as invalid, which in
turn breaks NAT.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e75b3e1c9b upstream.
Its irrelevant if the DF bit is set or not, we must pass packet to
stack in either case.
If the DF bit is set, we must pass it to stack so the appropriate
ICMP error can be generated.
If the DF is not set, we must pass it to stack for fragmentation.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----------------------------------------------------------------
This patch is not on mainline and is meant to 4.19 stable *only*.
After the patch description there's a reasoning about that.
-----------------------------------------------------------------
Commit cd4a4ae468 ("block: don't use blocking queue entered for
recursive bio submits") introduced the flag BIO_QUEUE_ENTERED in order
split bios bypass the blocking queue entering routine and use the live
non-blocking version. It was a result of an extensive discussion in
a linux-block thread[0], and the purpose of this change was to prevent
a hung task waiting on a reference to drop.
Happens that md raid0 split bios all the time, and more important,
it changes their underlying device to the raid member. After the change
introduced by this flag's usage, we experience various crashes if a raid0
member is removed during a large write. This happens because the bio
reaches the live queue entering function when the queue of the raid0
member is dying.
A simple reproducer of this behavior is presented below:
a) Build kernel v4.19.56-stable with CONFIG_BLK_DEV_THROTTLING=y.
b) Create a raid0 md array with 2 NVMe devices as members, and mount
it with an ext4 filesystem.
c) Run the following oneliner (supposing the raid0 is mounted in /mnt):
(dd of=/mnt/tmp if=/dev/zero bs=1M count=999 &); sleep 0.3;
echo 1 > /sys/block/nvme1n1/device/device/remove
(whereas nvme1n1 is the 2nd array member)
This will trigger the following warning/oops:
------------[ cut here ]------------
BUG: unable to handle kernel NULL pointer dereference at 0000000000000155
PGD 0 P4D 0
Oops: 0000 [#1] SMP PTI
RIP: 0010:blk_throtl_bio+0x45/0x970
[...]
Call Trace:
generic_make_request_checks+0x1bf/0x690
generic_make_request+0x64/0x3f0
raid0_make_request+0x184/0x620 [raid0]
? raid0_make_request+0x184/0x620 [raid0]
md_handle_request+0x126/0x1a0
md_make_request+0x7b/0x180
generic_make_request+0x19e/0x3f0
submit_bio+0x73/0x140
[...]
This patch changes raid0 driver to fallback to the "old" blocking queue
entering procedure, by clearing the BIO_QUEUE_ENTERED from raid0 bios.
This prevents the crashes and restores the regular behavior of raid0
arrays when a member is removed during a large write.
[0] lore.kernel.org/linux-block/343bbbf6-64eb-879e-d19e-96aebb037d47@I-love.SAKURA.ne.jp
----------------------------
Why this is not on mainline?
----------------------------
The patch was originally submitted upstream in linux-raid and
linux-block mailing-lists - it was initially accepted by Song Liu,
but Christoph Hellwig[1] observed that there was a clean-up series
ready to be accepted from Ming Lei[2] that fixed the same issue.
The accepted patches from Ming's series in upstream are: commit
47cdee29ef ("block: move blk_exit_queue into __blk_release_queue") and
commit fe2008640a ("block: don't protect generic_make_request_checks
with blk_queue_enter"). Those patches basically do a clean-up in the
block layer involving:
1) Putting back blk_exit_queue() logic into __blk_release_queue(); that
path was changed in the past and the logic from blk_exit_queue() was
added to blk_cleanup_queue().
2) Removing the guard/protection in generic_make_request_checks() with
blk_queue_enter().
The problem with Ming's series for -stable is that it relies in the
legacy request IO path removal. So it's "backport-able" to v5.0+,
but doing that for early versions (like 4.19) would incur in complex
code changes. Hence, it was suggested by Christoph and Song Liu that
this patch was submitted to stable only; otherwise merging it upstream
would add code to fix a path removed in a subsequent commit.
[1] lore.kernel.org/linux-block/20190521172258.GA32702@infradead.org
[2] lore.kernel.org/linux-block/20190515030310.20393-1-ming.lei@redhat.com
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Fixes: cd4a4ae468 ("block: don't use blocking queue entered for recursive bio submits")
Signed-off-by: Guilherme G. Piccoli <gpiccoli@canonical.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----------------------------------------------------------------
This patch is not on mainline and is meant to 4.19 stable *only*.
After the patch description there's a reasoning about that.
-----------------------------------------------------------------
Commit 37f9579f4c ("blk-mq: Avoid that submitting a bio concurrently
with device removal triggers a crash") introduced a NULL pointer
dereference in generic_make_request(). The patch sets q to NULL and
enter_succeeded to false; right after, there's an 'if (enter_succeeded)'
which is not taken, and then the 'else' will dereference q in
blk_queue_dying(q).
This patch just moves the 'q = NULL' to a point in which it won't trigger
the oops, although the semantics of this NULLification remains untouched.
A simple test case/reproducer is as follows:
a) Build kernel v4.19.56-stable with CONFIG_BLK_CGROUP=n.
b) Create a raid0 md array with 2 NVMe devices as members, and mount
it with an ext4 filesystem.
c) Run the following oneliner (supposing the raid0 is mounted in /mnt):
(dd of=/mnt/tmp if=/dev/zero bs=1M count=999 &); sleep 0.3;
echo 1 > /sys/block/nvme1n1/device/device/remove
(whereas nvme1n1 is the 2nd array member)
This will trigger the following oops:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000078
PGD 0 P4D 0
Oops: 0000 [#1] SMP PTI
RIP: 0010:generic_make_request+0x32b/0x400
Call Trace:
submit_bio+0x73/0x140
ext4_io_submit+0x4d/0x60
ext4_writepages+0x626/0xe90
do_writepages+0x4b/0xe0
[...]
This patch has no functional changes and preserves the md/raid0 behavior
when a member is removed before kernel v4.17.
----------------------------
Why this is not on mainline?
----------------------------
The patch was originally submitted upstream in linux-raid and
linux-block mailing-lists - it was initially accepted by Song Liu,
but Christoph Hellwig[0] observed that there was a clean-up series
ready to be accepted from Ming Lei[1] that fixed the same issue.
The accepted patches from Ming's series in upstream are: commit
47cdee29ef ("block: move blk_exit_queue into __blk_release_queue") and
commit fe2008640a ("block: don't protect generic_make_request_checks
with blk_queue_enter"). Those patches basically do a clean-up in the
block layer involving:
1) Putting back blk_exit_queue() logic into __blk_release_queue(); that
path was changed in the past and the logic from blk_exit_queue() was
added to blk_cleanup_queue().
2) Removing the guard/protection in generic_make_request_checks() with
blk_queue_enter().
The problem with Ming's series for -stable is that it relies in the
legacy request IO path removal. So it's "backport-able" to v5.0+,
but doing that for early versions (like 4.19) would incur in complex
code changes. Hence, it was suggested by Christoph and Song Liu that
this patch was submitted to stable only; otherwise merging it upstream
would add code to fix a path removed in a subsequent commit.
[0] lore.kernel.org/linux-block/20190521172258.GA32702@infradead.org
[1] lore.kernel.org/linux-block/20190515030310.20393-1-ming.lei@redhat.com
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Tested-by: Eric Ren <renzhengeek@gmail.com>
Fixes: 37f9579f4c ("blk-mq: Avoid that submitting a bio concurrently with device removal triggers a crash")
Signed-off-by: Guilherme G. Piccoli <gpiccoli@canonical.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "bus" parameter has two functions - providing unique names for
multiple instances of the overlay, and allowing the number of the bus
(i.e. "i2c-<bus>") to be specified. The second function hasn't worked
as intended because the overlay doesn't include a "reg" property and
the firmware intentionally won't create a "reg" property if one doesn't
already exist.
Allow the bus numbering scheme to work as intended by providing a "reg"
with a default value that means "the next available one".
See: https://github.com/raspberrypi/linux/issues/3062
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Commit 9de93b04df upstream.
Probe function fails to recognize that upstream clock actually
doesn't yet exist because clock driver has not been initialized.
Actually try to go get the clock and test for its existence
before trying to set up a downstream clock based upon it.
This fixes a bug that causes the i2c driver not to work with
monolithic kernels.
Fixes: bebff81fb8 ("i2c: bcm2835: Model Divider in CCF")
Signed-off-by: Annaliese McDermond <nh6z@nh6z.net>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit 4a5cfa3946 upstream.
If any of the clock code in the probe fails and returns, the IRQ
will not be freed. Moving the IRQ request to last allows it to
be freed on any errors further up in the probe function. devm_
calls can apparently not be used because there are some potential
race conditions that will arise.
Fixes: bebff81fb8 ("i2c: bcm2835: Model Divider in CCF")
Signed-off-by: Annaliese McDermond <nh6z@nh6z.net>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Rename the various pi3- overlays to be more generic, listing
the devices they apply to in the README. The original names are
retained for backwards compatibility as files that just include
the new versions - the README marks them as being deprecated.
See: https://github.com/raspberrypi/firmware/issues/1174
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
As a result of being loaded by the POE HAT EEPROM, the rpi-poe overlay
doesn't expose parameters in the usual way; instead it adds them to
the base Device Tree, and the user is expected to use "dtparam=..."
to access them.
To make the documentation correct and to protect users who load the
overlay explicitly, expecting to be able to use the parameters, add
real parameters to the overlay as well.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
2019-07-05 09:22:10 +01:00
106 changed files with 792 additions and 428 deletions
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
