dts: bcm2711: Disable DVP by default

The HDMI DVP should be disabled by default as is the case for other
display related drivers. This changes resolves an issue when using
the legacy firmware display driver where the DVP caused the 108 MHz
clock in HDMI TX to be gated off when Linux started. This effectively
stopped the firmware from being able to change the HDMI analog PHY
registers.

Add a fragment to re-enable this in vc4-kms-v3d-pi4-overlay

.github/ISSUE_TEMPLATE/bug_report.md

@@ -0,0 +1,34 @@
+---
+name: Bug report
+about: Create a report to help us fix your issue
+
+---
+
+**Is this the right place for my bug report?**
+This repository contains the Linux kernel used on the Raspberry Pi. If you believe that the issue you are seeing is kernel-related, this is the right place. If not, we have other repositories for the GPU firmware at [github.com/raspberrypi/firmware](https://github.com/raspberrypi/firmware) and Raspberry Pi userland applications at [github.com/raspberrypi/userland](https://github.com/raspberrypi/userland). If you have problems with the Raspbian distribution packages, report them in the [github.com/RPi-Distro/repo](https://github.com/RPi-Distro/repo). If you simply have a question, then [the Raspberry Pi forums](https://www.raspberrypi.org/forums) are the best place to ask it.
+
+**Describe the bug**
+Add a clear and concise description of what you think the bug is.
+
+**To reproduce**
+List the steps required to reproduce the issue.
+
+**Expected behaviour**
+Add a clear and concise description of what you expected to happen.
+
+**Actual behaviour**
+Add a clear and concise description of what actually happened.
+
+**System**
+ Copy and paste the results of the raspinfo command in to this section. Alternatively, copy and paste a pastebin link, or add answers to the following questions:
+
+* Which model of Raspberry Pi? e.g. Pi3B+, PiZeroW
+* Which OS and version (`cat /etc/rpi-issue`)?
+* Which firmware version (`vcgencmd version`)?
+* Which kernel version (`uname -a`)?
+
+**Logs**
+If applicable, add the relevant output from `dmesg` or similar.
+
+**Additional context**
+Add any other relevant context for the problem.

.gitignore

@@ -17,6 +17,7 @@
 *.c.[012]*.*
 *.dt.yaml
 *.dtb
+*.dtbo
 *.dtb.S
 *.dwo
 *.elf

Documentation/ABI/testing/sysfs-devices-system-cpu

@@ -486,6 +486,7 @@ What:		/sys/devices/system/cpu/vulnerabilities
 		/sys/devices/system/cpu/vulnerabilities/spec_store_bypass
 		/sys/devices/system/cpu/vulnerabilities/l1tf
 		/sys/devices/system/cpu/vulnerabilities/mds
+		/sys/devices/system/cpu/vulnerabilities/srbds
 		/sys/devices/system/cpu/vulnerabilities/tsx_async_abort
 		/sys/devices/system/cpu/vulnerabilities/itlb_multihit
 Date:		January 2018

Documentation/ABI/testing/sysfs-driver-w1_therm

@@ -0,0 +1,116 @@
+What:		/sys/bus/w1/devices/.../alarms
+Date:		May 2020
+Contact:	Akira Shimahara <akira215corp@gmail.com>
+Description:
+		(RW) read or write TH and TL (Temperature High an Low) alarms.
+		Values shall be space separated and in the device range
+		(typical -55 degC to 125 degC), if not values will be trimmed
+		to device min/max capabilities. Values are integer as they are
+		stored in a 8bit register in the device. Lowest value is
+		automatically put to TL. Once set, alarms could be search at
+		master level, refer to Documentation/w1/w1_generic.rst for
+		detailed information
+Users:		any user space application which wants to communicate with
+		w1_term device
+
+
+What:		/sys/bus/w1/devices/.../eeprom
+Date:		May 2020
+Contact:	Akira Shimahara <akira215corp@gmail.com>
+Description:
+		(WO) writing that file will either trigger a save of the
+		device data to its embedded EEPROM, either restore data
+		embedded in device EEPROM. Be aware that devices support
+		limited EEPROM writing cycles (typical 50k)
+			* 'save': save device RAM to EEPROM
+			* 'restore': restore EEPROM data in device RAM
+Users:		any user space application which wants to communicate with
+		w1_term device
+
+
+What:		/sys/bus/w1/devices/.../ext_power
+Date:		May 2020
+Contact:	Akira Shimahara <akira215corp@gmail.com>
+Description:
+		(RO) return the power status by asking the device
+			* '0': device parasite powered
+			* '1': device externally powered
+			* '-xx': xx is kernel error when reading power status
+Users:		any user space application which wants to communicate with
+		w1_term device
+
+
+What:		/sys/bus/w1/devices/.../resolution
+Date:		May 2020
+Contact:	Akira Shimahara <akira215corp@gmail.com>
+Description:
+		(RW) get or set the device resolution (on supported devices,
+		if not, this entry is not present). Note that the resolution
+		will be changed only in device RAM, so it will be cleared when
+		power is lost. Trigger a 'save' to EEPROM command to keep
+		values after power-on. Read or write are :
+			* '9..12': device resolution in bit
+			or resolution to set in bit
+			* '-xx': xx is kernel error when reading the resolution
+			* Anything else: do nothing
+Users:		any user space application which wants to communicate with
+		w1_term device
+
+
+What:		/sys/bus/w1/devices/.../temperature
+Date:		May 2020
+Contact:	Akira Shimahara <akira215corp@gmail.com>
+Description:
+		(RO) return the temperature in 1/1000 degC.
+			* If a bulk read has been triggered, it will directly
+			return the temperature computed when the bulk read
+			occurred, if available. If not yet available, nothing
+			is returned (a debug kernel message is sent), you
+			should retry later on.
+			* If no bulk read has been triggered, it will trigger
+			a conversion and send the result. Note that the
+			conversion duration depend on the resolution (if
+			device support this feature). It takes 94ms in 9bits
+			resolution, 750ms for 12bits.
+Users:		any user space application which wants to communicate with
+		w1_term device
+
+
+What:		/sys/bus/w1/devices/.../w1_slave
+Date:		May 2020
+Contact:	Akira Shimahara <akira215corp@gmail.com>
+Description:
+		(RW) return the temperature in 1/1000 degC.
+		*read*: return 2 lines with the hexa output data sent on the
+		bus, return the CRC check and temperature in 1/1000 degC
+		*write* :
+			* '0' : save the 2 or 3 bytes to the device EEPROM
+			(i.e. TH, TL and config register)
+			* '9..12' : set the device resolution in RAM
+			(if supported)
+			* Anything else: do nothing
+		refer to Documentation/w1/slaves/w1_therm.rst for detailed
+		information.
+Users:		any user space application which wants to communicate with
+		w1_term device
+
+
+What:		/sys/bus/w1/devices/w1_bus_masterXX/therm_bulk_read
+Date:		May 2020
+Contact:	Akira Shimahara <akira215corp@gmail.com>
+Description:
+		(RW) trigger a bulk read conversion. read the status
+		*read*:
+			* '-1': conversion in progress on at least 1 sensor
+			* '1' :	conversion complete but at least one sensor
+				value has not been read yet
+			* '0' :	no bulk operation. Reading temperature will
+				trigger a conversion on each device
+		*write*: 'trigger': trigger a bulk read on all supporting
+			devices on the bus
+		Note that if a bulk read is sent but one sensor is not read
+		immediately, the next access to temperature on this device
+		will return the temperature measured at the time of issue
+		of the bulk read command (not the current temperature).
+Users:		any user space application which wants to communicate with
+		w1_term device

Documentation/admin-guide/hw-vuln/index.rst

@@ -14,3 +14,4 @@ are configurable at compile, boot or run time.
    mds
    tsx_async_abort
    multihit.rst
+   special-register-buffer-data-sampling.rst

Documentation/admin-guide/hw-vuln/special-register-buffer-data-sampling.rst

@@ -0,0 +1,149 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+SRBDS - Special Register Buffer Data Sampling
+=============================================
+
+SRBDS is a hardware vulnerability that allows MDS :doc:`mds` techniques to
+infer values returned from special register accesses.  Special register
+accesses are accesses to off core registers.  According to Intel's evaluation,
+the special register reads that have a security expectation of privacy are
+RDRAND, RDSEED and SGX EGETKEY.
+
+When RDRAND, RDSEED and EGETKEY instructions are used, the data is moved
+to the core through the special register mechanism that is susceptible
+to MDS attacks.
+
+Affected processors
+--------------------
+Core models (desktop, mobile, Xeon-E3) that implement RDRAND and/or RDSEED may
+be affected.
+
+A processor is affected by SRBDS if its Family_Model and stepping is
+in the following list, with the exception of the listed processors
+exporting MDS_NO while Intel TSX is available yet not enabled. The
+latter class of processors are only affected when Intel TSX is enabled
+by software using TSX_CTRL_MSR otherwise they are not affected.
+
+  =============  ============  ========
+  common name    Family_Model  Stepping
+  =============  ============  ========
+  IvyBridge      06_3AH        All
+
+  Haswell        06_3CH        All
+  Haswell_L      06_45H        All
+  Haswell_G      06_46H        All
+
+  Broadwell_G    06_47H        All
+  Broadwell      06_3DH        All
+
+  Skylake_L      06_4EH        All
+  Skylake        06_5EH        All
+
+  Kabylake_L     06_8EH        <= 0xC
+  Kabylake       06_9EH        <= 0xD
+  =============  ============  ========
+
+Related CVEs
+------------
+
+The following CVE entry is related to this SRBDS issue:
+
+    ==============  =====  =====================================
+    CVE-2020-0543   SRBDS  Special Register Buffer Data Sampling
+    ==============  =====  =====================================
+
+Attack scenarios
+----------------
+An unprivileged user can extract values returned from RDRAND and RDSEED
+executed on another core or sibling thread using MDS techniques.
+
+
+Mitigation mechanism
+-------------------
+Intel will release microcode updates that modify the RDRAND, RDSEED, and
+EGETKEY instructions to overwrite secret special register data in the shared
+staging buffer before the secret data can be accessed by another logical
+processor.
+
+During execution of the RDRAND, RDSEED, or EGETKEY instructions, off-core
+accesses from other logical processors will be delayed until the special
+register read is complete and the secret data in the shared staging buffer is
+overwritten.
+
+This has three effects on performance:
+
+#. RDRAND, RDSEED, or EGETKEY instructions have higher latency.
+
+#. Executing RDRAND at the same time on multiple logical processors will be
+   serialized, resulting in an overall reduction in the maximum RDRAND
+   bandwidth.
+
+#. Executing RDRAND, RDSEED or EGETKEY will delay memory accesses from other
+   logical processors that miss their core caches, with an impact similar to
+   legacy locked cache-line-split accesses.
+
+The microcode updates provide an opt-out mechanism (RNGDS_MITG_DIS) to disable
+the mitigation for RDRAND and RDSEED instructions executed outside of Intel
+Software Guard Extensions (Intel SGX) enclaves. On logical processors that
+disable the mitigation using this opt-out mechanism, RDRAND and RDSEED do not
+take longer to execute and do not impact performance of sibling logical
+processors memory accesses. The opt-out mechanism does not affect Intel SGX
+enclaves (including execution of RDRAND or RDSEED inside an enclave, as well
+as EGETKEY execution).
+
+IA32_MCU_OPT_CTRL MSR Definition
+--------------------------------
+Along with the mitigation for this issue, Intel added a new thread-scope
+IA32_MCU_OPT_CTRL MSR, (address 0x123). The presence of this MSR and
+RNGDS_MITG_DIS (bit 0) is enumerated by CPUID.(EAX=07H,ECX=0).EDX[SRBDS_CTRL =
+9]==1. This MSR is introduced through the microcode update.
+
+Setting IA32_MCU_OPT_CTRL[0] (RNGDS_MITG_DIS) to 1 for a logical processor
+disables the mitigation for RDRAND and RDSEED executed outside of an Intel SGX
+enclave on that logical processor. Opting out of the mitigation for a
+particular logical processor does not affect the RDRAND and RDSEED mitigations
+for other logical processors.
+
+Note that inside of an Intel SGX enclave, the mitigation is applied regardless
+of the value of RNGDS_MITG_DS.
+
+Mitigation control on the kernel command line
+---------------------------------------------
+The kernel command line allows control over the SRBDS mitigation at boot time
+with the option "srbds=".  The option for this is:
+
+  ============= =============================================================
+  off           This option disables SRBDS mitigation for RDRAND and RDSEED on
+                affected platforms.
+  ============= =============================================================
+
+SRBDS System Information
+-----------------------
+The Linux kernel provides vulnerability status information through sysfs.  For
+SRBDS this can be accessed by the following sysfs file:
+/sys/devices/system/cpu/vulnerabilities/srbds
+
+The possible values contained in this file are:
+
+ ============================== =============================================
+ Not affected                   Processor not vulnerable
+ Vulnerable                     Processor vulnerable and mitigation disabled
+ Vulnerable: No microcode       Processor vulnerable and microcode is missing
+                                mitigation
+ Mitigation: Microcode          Processor is vulnerable and mitigation is in
+                                effect.
+ Mitigation: TSX disabled       Processor is only vulnerable when TSX is
+                                enabled while this system was booted with TSX
+                                disabled.
+ Unknown: Dependent on
+ hypervisor status              Running on virtual guest processor that is
+                                affected but with no way to know if host
+                                processor is mitigated or vulnerable.
+ ============================== =============================================
+
+SRBDS Default mitigation
+------------------------
+This new microcode serializes processor access during execution of RDRAND,
+RDSEED ensures that the shared buffer is overwritten before it is released for
+reuse.  Use the "srbds=off" kernel command line to disable the mitigation for
+RDRAND and RDSEED.

Documentation/admin-guide/kernel-parameters.txt

@@ -4579,6 +4579,26 @@
 	spia_pedr=
 	spia_peddr=
 
+	srbds=		[X86,INTEL]
+			Control the Special Register Buffer Data Sampling
+			(SRBDS) mitigation.
+
+			Certain CPUs are vulnerable to an MDS-like
+			exploit which can leak bits from the random
+			number generator.
+
+			By default, this issue is mitigated by
+			microcode.  However, the microcode fix can cause
+			the RDRAND and RDSEED instructions to become
+			much slower.  Among other effects, this will
+			result in reduced throughput from /dev/urandom.
+
+			The microcode mitigation can be disabled with
+			the following option:
+
+			off:    Disable mitigation and remove
+				performance impact to RDRAND and RDSEED
+
 	srcutree.counter_wrap_check [KNL]
 			Specifies how frequently to check for
 			grace-period sequence counter wrap for the

Documentation/devicetree/bindings/clock/brcm,bcm2711-dvp.yaml

@@ -0,0 +1,47 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/clock/brcm,bcm2711-dvp.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Broadcom BCM2711 HDMI DVP Device Tree Bindings
+
+maintainers:
+  - Maxime Ripard <mripard@kernel.org>
+
+properties:
+  "#clock-cells":
+    const: 1
+
+  "#reset-cells":
+    const: 1
+
+  compatible:
+    const: brcm,brcm2711-dvp
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+required:
+  - "#clock-cells"
+  - "#reset-cells"
+  - compatible
+  - reg
+  - clocks
+
+additionalProperties: false
+
+examples:
+  - |
+    dvp: clock@7ef00000 {
+        compatible = "brcm,brcm2711-dvp";
+        reg = <0x7ef00000 0x10>;
+        clocks = <&clk_108MHz>;
+        #clock-cells = <1>;
+        #reset-cells = <1>;
+    };
+
+...

Documentation/devicetree/bindings/clock/raspberrypi,firmware-clocks.yaml

@@ -0,0 +1,39 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/clock/raspberrypi,firmware-clocks.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: RaspberryPi Firmware Clocks Device Tree Bindings
+
+maintainers:
+  - Maxime Ripard <mripard@kernel.org>
+
+properties:
+  "#clock-cells":
+    const: 1
+
+  compatible:
+    const: raspberrypi,firmware-clocks
+
+  raspberrypi,firmware:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description: >
+      Phandle to the mailbox node to communicate with the firmware.
+
+required:
+  - "#clock-cells"
+  - compatible
+  - raspberrypi,firmware
+
+additionalProperties: false
+
+examples:
+  - |
+    firmware_clocks: firmware-clocks {
+        compatible = "raspberrypi,firmware-clocks";
+        raspberrypi,firmware = <&firmware>;
+        #clock-cells = <1>;
+    };
+
+...

Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt

@@ -1,174 +0,0 @@
-Broadcom VC4 (VideoCore4) GPU
-
-The VC4 device present on the Raspberry Pi includes a display system
-with HDMI output and the HVS (Hardware Video Scaler) for compositing
-display planes.
-
-Required properties for VC4:
-- compatible:	Should be "brcm,bcm2835-vc4" or "brcm,cygnus-vc4"
-
-Required properties for Pixel Valve:
-- compatible:	Should be one of "brcm,bcm2835-pixelvalve0",
-		  "brcm,bcm2835-pixelvalve1", or "brcm,bcm2835-pixelvalve2"
-- reg:		Physical base address and length of the PV's registers
-- interrupts:	The interrupt number
-		  See bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt
-
-Required properties for HVS:
-- compatible:	Should be "brcm,bcm2835-hvs"
-- reg:		Physical base address and length of the HVS's registers
-- interrupts:	The interrupt number
-		  See bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt
-
-Required properties for HDMI
-- compatible:	Should be "brcm,bcm2835-hdmi"
-- reg:		Physical base address and length of the two register ranges
-		  ("HDMI" and "HD", in that order)
-- interrupts:	The interrupt numbers
-		  See bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt
-- ddc:		phandle of the I2C controller used for DDC EDID probing
-- clocks:	a) hdmi: The HDMI state machine clock
-		b) pixel: The pixel clock.
-
-Optional properties for HDMI:
-- hpd-gpios:	The GPIO pin for HDMI hotplug detect (if it doesn't appear
-		  as an interrupt/status bit in the HDMI controller
-		  itself).  See bindings/pinctrl/brcm,bcm2835-gpio.txt
-- dmas:		Should contain one entry pointing to the DMA channel used to
-		transfer audio data
-- dma-names:	Should contain "audio-rx"
-
-Required properties for DPI:
-- compatible:	Should be "brcm,bcm2835-dpi"
-- reg:		Physical base address and length of the registers
-- clocks:	a) core: The core clock the unit runs on
-		b) pixel: The pixel clock that feeds the pixelvalve
-- port:		Port node with a single endpoint connecting to the panel
-		  device, as defined in [1]
-
-Required properties for VEC:
-- compatible:	Should be "brcm,bcm2835-vec"
-- reg:		Physical base address and length of the registers
-- clocks:	The core clock the unit runs on
-- interrupts:	The interrupt number
-		  See bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt
-
-Required properties for V3D:
-- compatible:	Should be "brcm,bcm2835-v3d" or "brcm,cygnus-v3d"
-- reg:		Physical base address and length of the V3D's registers
-- interrupts:	The interrupt number
-		  See bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt
-
-Optional properties for V3D:
-- clocks:	The clock the unit runs on
-
-Required properties for DSI:
-- compatible:	Should be "brcm,bcm2835-dsi0" or "brcm,bcm2835-dsi1"
-- reg:		Physical base address and length of the DSI block's registers
-- interrupts:	The interrupt number
-		  See bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt
-- clocks:	a) phy: The DSI PLL clock feeding the DSI analog PHY
-		b) escape: The DSI ESC clock from CPRMAN
-		c) pixel: The DSI pixel clock from CPRMAN
-- clock-output-names:
-		The 3 clocks output from the DSI analog PHY: dsi[01]_byte,
-		dsi[01]_ddr2, and dsi[01]_ddr
-
-Required properties for the TXP (writeback) block:
-- compatible:	Should be "brcm,bcm2835-txp"
-- reg:		Physical base address and length of the TXP block's registers
-- interrupts:	The interrupt number
-		  See bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt
-
-[1] Documentation/devicetree/bindings/media/video-interfaces.txt
-
-Example:
-pixelvalve@7e807000 {
-	compatible = "brcm,bcm2835-pixelvalve2";
-	reg = <0x7e807000 0x100>;
-	interrupts = <2 10>; /* pixelvalve */
-};
-
-hvs@7e400000 {
-	compatible = "brcm,bcm2835-hvs";
-	reg = <0x7e400000 0x6000>;
-	interrupts = <2 1>;
-};
-
-hdmi: hdmi@7e902000 {
-	compatible = "brcm,bcm2835-hdmi";
-	reg = <0x7e902000 0x600>,
-	      <0x7e808000 0x100>;
-	interrupts = <2 8>, <2 9>;
-	ddc = <&i2c2>;
-	hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
-	clocks = <&clocks BCM2835_PLLH_PIX>,
-		 <&clocks BCM2835_CLOCK_HSM>;
-	clock-names = "pixel", "hdmi";
-};
-
-dpi: dpi@7e208000 {
-	compatible = "brcm,bcm2835-dpi";
-	reg = <0x7e208000 0x8c>;
-	clocks = <&clocks BCM2835_CLOCK_VPU>,
-	         <&clocks BCM2835_CLOCK_DPI>;
-	clock-names = "core", "pixel";
-	#address-cells = <1>;
-	#size-cells = <0>;
-
-	port {
-		dpi_out: endpoint@0 {
-			remote-endpoint = <&panel_in>;
-		};
-	};
-};
-
-dsi1: dsi@7e700000 {
-	compatible = "brcm,bcm2835-dsi1";
-	reg = <0x7e700000 0x8c>;
-	interrupts = <2 12>;
-	#address-cells = <1>;
-	#size-cells = <0>;
-	#clock-cells = <1>;
-
-	clocks = <&clocks BCM2835_PLLD_DSI1>,
-		 <&clocks BCM2835_CLOCK_DSI1E>,
-		 <&clocks BCM2835_CLOCK_DSI1P>;
-	clock-names = "phy", "escape", "pixel";
-
-	clock-output-names = "dsi1_byte", "dsi1_ddr2", "dsi1_ddr";
-
-	pitouchscreen: panel@0 {
-		compatible = "raspberrypi,touchscreen";
-		reg = <0>;
-
-		<...>
-	};
-};
-
-vec: vec@7e806000 {
-	compatible = "brcm,bcm2835-vec";
-	reg = <0x7e806000 0x1000>;
-	clocks = <&clocks BCM2835_CLOCK_VEC>;
-	interrupts = <2 27>;
-};
-
-v3d: v3d@7ec00000 {
-	compatible = "brcm,bcm2835-v3d";
-	reg = <0x7ec00000 0x1000>;
-	interrupts = <1 10>;
-};
-
-vc4: gpu {
-	compatible = "brcm,bcm2835-vc4";
-};
-
-panel: panel {
-	compatible = "ontat,yx700wv03", "simple-panel";
-
-	port {
-		panel_in: endpoint {
-			remote-endpoint = <&dpi_out>;
-		};
-	};
-};

Documentation/devicetree/bindings/display/brcm,bcm2835-dpi.yaml

@@ -0,0 +1,72 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/brcm,bcm2835-dpi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Broadcom VC4 (VideoCore4) DPI Controller
+
+maintainers:
+  - Eric Anholt <eric@anholt.net>
+
+properties:
+  compatible:
+    const: brcm,bcm2835-dpi
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: The core clock the unit runs on
+      - description: The pixel clock that feeds the pixelvalve
+
+  clock-names:
+    items:
+      - const: core
+      - const: pixel
+
+  port:
+    type: object
+    description: >
+      Port node with a single endpoint connecting to the panel, as
+      defined in Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - port
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/bcm2835.h>
+
+    panel: panel {
+        compatible = "ontat,yx700wv03", "simple-panel";
+
+        port {
+            panel_in: endpoint {
+                remote-endpoint = <&dpi_out>;
+            };
+        };
+    };
+
+    dpi: dpi@7e208000 {
+        compatible = "brcm,bcm2835-dpi";
+        reg = <0x7e208000 0x8c>;
+        clocks = <&clocks BCM2835_CLOCK_VPU>,
+                 <&clocks BCM2835_CLOCK_DPI>;
+        clock-names = "core", "pixel";
+
+        port {
+            dpi_out: endpoint {
+                remote-endpoint = <&panel_in>;
+            };
+        };
+    };
+
+...

Documentation/devicetree/bindings/display/brcm,bcm2835-dsi0.yaml

@@ -0,0 +1,84 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/brcm,bcm2835-dsi0.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Broadcom VC4 (VideoCore4) DSI Controller
+
+maintainers:
+  - Eric Anholt <eric@anholt.net>
+
+properties:
+  "#clock-cells":
+    const: 1
+
+  compatible:
+    enum:
+      - brcm,bcm2835-dsi0
+      - brcm,bcm2835-dsi1
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: The DSI PLL clock feeding the DSI analog PHY
+      - description: The DSI ESC clock
+      - description: The DSI pixel clock
+
+  clock-names:
+    items:
+      - const: phy
+      - const: escape
+      - const: pixel
+
+  clock-output-names: true
+    # FIXME: The meta-schemas don't seem to allow it for now
+    # items:
+    #   - description: The DSI byte clock for the PHY
+    #   - description: The DSI DDR2 clock
+    #   - description: The DSI DDR clock
+
+  interrupts:
+    maxItems: 1
+
+required:
+  - "#clock-cells"
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - clock-output-names
+  - interrupts
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/bcm2835.h>
+
+    dsi1: dsi@7e700000 {
+        compatible = "brcm,bcm2835-dsi1";
+        reg = <0x7e700000 0x8c>;
+        interrupts = <2 12>;
+        #address-cells = <1>;
+        #size-cells = <0>;
+        #clock-cells = <1>;
+
+        clocks = <&clocks BCM2835_PLLD_DSI1>,
+                 <&clocks BCM2835_CLOCK_DSI1E>,
+                 <&clocks BCM2835_CLOCK_DSI1P>;
+        clock-names = "phy", "escape", "pixel";
+
+        clock-output-names = "dsi1_byte", "dsi1_ddr2", "dsi1_ddr";
+
+        pitouchscreen: panel@0 {
+            compatible = "raspberrypi,touchscreen";
+            reg = <0>;
+
+            /* ... */
+        };
+    };
+
+...

Documentation/devicetree/bindings/display/brcm,bcm2835-hdmi.yaml

@@ -0,0 +1,180 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/brcm,bcm2835-hdmi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Broadcom VC4 (VideoCore4) HDMI Controller
+
+maintainers:
+  - Eric Anholt <eric@anholt.net>
+
+properties:
+  compatible:
+    enum:
+      - brcm,bcm2835-hdmi
+      - brcm,bcm2711-hdmi0
+      - brcm,bcm2711-hdmi1
+
+  reg:
+    oneOf:
+      - items:
+        - description: HDMI register range
+        - description: HD register range
+
+      - items:
+        - description: HDMI controller register range
+        - description: DVP register range
+        - description: HDMI PHY register range
+        - description: Rate Manager register range
+        - description: Packet RAM register range
+        - description: Metadata RAM register range
+        - description: CSC register range
+        - description: CEC register range
+        - description: HD register range
+
+  reg-names:
+    items:
+      - const: hdmi
+      - const: dvp
+      - const: phy
+      - const: rm
+      - const: packet
+      - const: metadata
+      - const: csc
+      - const: cec
+      - const: hd
+
+  interrupts:
+    minItems: 2
+
+  clocks:
+    oneOf:
+      - items:
+        - description: The pixel clock
+        - description: The HDMI state machine clock
+
+      - items:
+        - description: The HDMI state machine clock
+
+  clock-names:
+    oneOf:
+      - items:
+        - const: pixel
+        - const: hdmi
+
+      - const: hdmi
+
+  ddc:
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/phandle
+    description: >
+      Phandle of the I2C controller used for DDC EDID probing
+
+  hpd-gpios:
+    description: >
+      The GPIO pin for the HDMI hotplug detect (if it doesn't appear
+      as an interrupt/status bit in the HDMI controller itself)
+
+  dmas:
+    maxItems: 1
+    description: >
+      Should contain one entry pointing to the DMA channel used to
+      transfer audio data.
+
+  dma-names:
+    const: audio-rx
+
+  resets:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - ddc
+
+additionalProperties: false
+
+if:
+  properties:
+    compatible:
+      contains:
+        enum:
+          - brcm,bcm2711-hdmi0
+          - brcm,bcm2711-hdmi1
+
+then:
+  properties:
+    reg:
+      minItems: 9
+
+    clocks:
+      maxItems: 1
+
+    clock-names:
+      maxItems: 1
+
+  required:
+    - reg-names
+    - resets
+
+else:
+  properties:
+    reg:
+      maxItems: 2
+
+    clocks:
+      minItems: 2
+
+    clock-names:
+      minItems: 2
+
+  required:
+    - interrupts
+
+examples:
+  - |
+    #include <dt-bindings/clock/bcm2835.h>
+    #include <dt-bindings/gpio/gpio.h>
+
+    hdmi: hdmi@7e902000 {
+        compatible = "brcm,bcm2835-hdmi";
+        reg = <0x7e902000 0x600>,
+              <0x7e808000 0x100>;
+        interrupts = <2 8>, <2 9>;
+        ddc = <&i2c2>;
+        hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
+        clocks = <&clocks BCM2835_PLLH_PIX>,
+                 <&clocks BCM2835_CLOCK_HSM>;
+        clock-names = "pixel", "hdmi";
+    };
+
+  - |
+    hdmi0: hdmi@7ef00700 {
+        compatible = "brcm,bcm2711-hdmi0";
+        reg = <0x7ef00700 0x300>,
+              <0x7ef00300 0x200>,
+              <0x7ef00f00 0x80>,
+              <0x7ef00f80 0x80>,
+              <0x7ef01b00 0x200>,
+              <0x7ef01f00 0x400>,
+              <0x7ef00200 0x80>,
+              <0x7ef04300 0x100>,
+              <0x7ef20000 0x100>;
+        reg-names = "hdmi",
+                    "dvp",
+                    "phy",
+                    "rm",
+                    "packet",
+                    "metadata",
+                    "csc",
+                    "cec",
+                    "hd";
+        clocks = <&firmware_clocks 13>;
+        clock-names = "hdmi";
+        resets = <&dvp 0>;
+        ddc = <&ddc0>;
+    };
+
+...

Documentation/devicetree/bindings/display/brcm,bcm2835-hvs.yaml

@@ -0,0 +1,37 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/brcm,bcm2835-hvs.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Broadcom VC4 (VideoCore4) Hardware Video Scaler
+
+maintainers:
+  - Eric Anholt <eric@anholt.net>
+
+properties:
+  compatible:
+    const: brcm,bcm2835-hvs
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+additionalProperties: false
+
+examples:
+  - |
+    hvs@7e400000 {
+        compatible = "brcm,bcm2835-hvs";
+        reg = <0x7e400000 0x6000>;
+        interrupts = <2 1>;
+    };
+
+...

Documentation/devicetree/bindings/display/brcm,bcm2835-pixelvalve0.yaml

@@ -0,0 +1,45 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/brcm,bcm2835-pixelvalve0.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Broadcom VC4 (VideoCore4) PixelValve
+
+maintainers:
+  - Eric Anholt <eric@anholt.net>
+
+properties:
+  compatible:
+    enum:
+      - brcm,bcm2835-pixelvalve0
+      - brcm,bcm2835-pixelvalve1
+      - brcm,bcm2835-pixelvalve2
+      - brcm,bcm2711-pixelvalve0
+      - brcm,bcm2711-pixelvalve1
+      - brcm,bcm2711-pixelvalve2
+      - brcm,bcm2711-pixelvalve3
+      - brcm,bcm2711-pixelvalve4
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+additionalProperties: false
+
+examples:
+  - |
+    pixelvalve@7e807000 {
+        compatible = "brcm,bcm2835-pixelvalve2";
+        reg = <0x7e807000 0x100>;
+        interrupts = <2 10>; /* pixelvalve */
+    };
+
+...

Documentation/devicetree/bindings/display/brcm,bcm2835-txp.yaml

@@ -0,0 +1,37 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/brcm,bcm2835-txp.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Broadcom VC4 (VideoCore4) TXP (writeback) Controller
+
+maintainers:
+  - Eric Anholt <eric@anholt.net>
+
+properties:
+  compatible:
+    const: brcm,bcm2835-txp
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+additionalProperties: false
+
+examples:
+  - |
+    txp: txp@7e004000 {
+        compatible = "brcm,bcm2835-txp";
+        reg = <0x7e004000 0x20>;
+        interrupts = <1 11>;
+    };
+
+...

Documentation/devicetree/bindings/display/brcm,bcm2835-v3d.yaml

@@ -0,0 +1,42 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/brcm,bcm2835-v3d.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Broadcom VC4 (VideoCore4) V3D GPU
+
+maintainers:
+  - Eric Anholt <eric@anholt.net>
+
+properties:
+  compatible:
+    enum:
+      - brcm,bcm2835-v3d
+      - brcm,cygnus-v3d
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+additionalProperties: false
+
+examples:
+  - |
+    v3d: v3d@7ec00000 {
+        compatible = "brcm,bcm2835-v3d";
+        reg = <0x7ec00000 0x1000>;
+        interrupts = <1 10>;
+    };
+
+...

Documentation/devicetree/bindings/display/brcm,bcm2835-vc4.yaml

@@ -0,0 +1,35 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/brcm,bcm2835-vc4.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Broadcom VC4 (VideoCore4) GPU
+
+maintainers:
+  - Eric Anholt <eric@anholt.net>
+
+description: >
+  The VC4 device present on the Raspberry Pi includes a display system
+  with HDMI output and the HVS (Hardware Video Scaler) for compositing
+  display planes.
+
+properties:
+  compatible:
+    enum:
+      - brcm,bcm2711-vc5
+      - brcm,bcm2835-vc4
+      - brcm,cygnus-vc4
+
+required:
+  - compatible
+
+additionalProperties: false
+
+examples:
+  - |
+    vc4: gpu {
+        compatible = "brcm,bcm2835-vc4";
+    };
+
+...

Documentation/devicetree/bindings/display/brcm,bcm2835-vec.yaml

@@ -0,0 +1,44 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/brcm,bcm2835-vec.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Broadcom VC4 (VideoCore4) VEC
+
+maintainers:
+  - Eric Anholt <eric@anholt.net>
+
+properties:
+  compatible:
+    const: brcm,bcm2835-vec
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - interrupts
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/bcm2835.h>
+
+    vec: vec@7e806000 {
+        compatible = "brcm,bcm2835-vec";
+        reg = <0x7e806000 0x1000>;
+        clocks = <&clocks BCM2835_CLOCK_VEC>;
+        interrupts = <2 27>;
+    };
+
+...

Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt

@@ -16,6 +16,9 @@ Required properties:
   Documentation/devicetree/bindings/graph.txt. This port should be connected
   to the input port of an attached HDMI or LVDS encoder chip.
 
+Optional properties:
+- pinctrl-names: Contain "default" and "sleep".
+
 Example:
 
 dpi0: dpi@1401d000 {
@@ -26,6 +29,9 @@ dpi0: dpi@1401d000 {
 		 <&mmsys CLK_MM_DPI_ENGINE>,
 		 <&apmixedsys CLK_APMIXED_TVDPLL>;
 	clock-names = "pixel", "engine", "pll";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&dpi_pin_func>;
+	pinctrl-1 = <&dpi_pin_idle>;
 
 	port {
 		dpi0_out: endpoint {

Documentation/devicetree/bindings/hwmon/rpi-poe-fan.txt

@@ -0,0 +1,55 @@
+Bindings for the Raspberry Pi PoE HAT fan
+
+Required properties:
+- compatible	: "raspberrypi,rpi-poe-fan"
+- firmware	: Reference to the RPi firmware device node
+- pwms		: the PWM that is used to control the PWM fan
+- cooling-levels      : PWM duty cycle values in a range from 0 to 255
+			which correspond to thermal cooling states
+
+Example:
+	fan0: rpi-poe-fan@0 {
+		compatible = "raspberrypi,rpi-poe-fan";
+		firmware = <&firmware>;
+		cooling-min-state = <0>;
+		cooling-max-state = <3>;
+		#cooling-cells = <2>;
+		cooling-levels = <0 50 150 255>;
+		status = "okay";
+	};
+
+	thermal-zones {
+		cpu_thermal: cpu-thermal {
+			trips {
+				threshold: trip-point@0 {
+					temperature = <45000>;
+					hysteresis = <5000>;
+					type = "active";
+				};
+				target: trip-point@1 {
+					temperature = <50000>;
+					hysteresis = <2000>;
+					type = "active";
+				};
+				cpu_hot: cpu_hot@0 {
+					temperature = <55000>;
+					hysteresis = <2000>;
+					type = "active";
+				};
+			};
+			cooling-maps {
+				map0 {
+					trip = <&threshold>;
+					cooling-device = <&fan0 0 1>;
+				};
+				map1 {
+					trip = <&target>;
+					cooling-device = <&fan0 1 2>;
+				};
+				map2 {
+					trip = <&cpu_hot>;
+					cooling-device = <&fan0 2 3>;
+				};
+			};
+		};
+	};

Documentation/devicetree/bindings/i2c/brcm,brcmstb-i2c.yaml

@@ -0,0 +1,97 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/i2c/brcm,brcmstb-i2c.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Broadcom STB BSC IIC Master Controller
+
+maintainers:
+  - Kamal Dasu <kdasu.kdev@gmail.com>
+
+allOf:
+  - $ref: /schemas/i2c/i2c-controller.yaml#
+
+properties:
+  compatible:
+    enum:
+      - brcm,bcm2711-hdmi-i2c
+      - brcm,brcmstb-i2c
+      - brcm,brcmper-i2c
+
+  reg:
+    minItems: 1
+    maxItems: 2
+    items:
+      - description: BSC register range
+      - description: Auto-I2C register range
+
+  reg-names:
+    items:
+      - const: bsc
+      - const: auto-i2c
+
+  interrupts:
+    maxItems: 1
+
+  interrupt-names:
+    maxItems: 1
+
+  clock-frequency:
+    enum:
+      - 46875
+      - 50000
+      - 93750
+      - 97500
+      - 187500
+      - 200000
+      - 375000
+      - 390000
+
+required:
+  - compatible
+  - reg
+  - clock-frequency
+
+unevaluatedProperties: false
+
+if:
+  properties:
+    compatible:
+      contains:
+        enum:
+          - brcm,bcm2711-hdmi-i2c
+
+then:
+  properties:
+    reg:
+      minItems: 2
+
+  required:
+    - reg-names
+
+else:
+  properties:
+    reg:
+      maxItems: 1
+
+examples:
+  - |
+      bsca: i2c@f0406200 {
+          clock-frequency = <390000>;
+          compatible = "brcm,brcmstb-i2c";
+          interrupt-parent = <&irq0_intc>;
+          reg = <0xf0406200 0x58>;
+          interrupts = <0x18>;
+          interrupt-names = "upg_bsca";
+      };
+
+  - |
+      ddc0: i2c@7ef04500 {
+          compatible = "brcm,bcm2711-hdmi-i2c";
+          reg = <0x7ef04500 0x100>, <0x7ef00b00 0x300>;
+          reg-names = "bsc", "auto-i2c";
+          clock-frequency = <390000>;
+      };
+
+...

Documentation/devicetree/bindings/i2c/i2c-brcmstb.txt

@@ -1,26 +0,0 @@
-Broadcom stb bsc iic master controller
-
-Required properties:
-
-- compatible: should be "brcm,brcmstb-i2c" or "brcm,brcmper-i2c"
-- clock-frequency: 32-bit decimal value of iic master clock freqency in Hz
-		   valid values are 375000, 390000, 187500, 200000
-		   93750, 97500, 46875 and 50000
-- reg: specifies the base physical address and size of the registers
-
-Optional properties :
-
-- interrupts: specifies the interrupt number, the irq line to be used
-- interrupt-names: Interrupt name string
-
-Example:
-
-bsca: i2c@f0406200 {
-      clock-frequency = <390000>;
-      compatible = "brcm,brcmstb-i2c";
-      interrupt-parent = <&irq0_intc>;
-      reg = <0xf0406200 0x58>;
-      interrupts = <0x18>;
-      interrupt-names = "upg_bsca";
-};
-

Documentation/devicetree/bindings/media/bcm2835-unicam.txt

@@ -0,0 +1,85 @@
+Broadcom BCM283x Camera Interface (Unicam)
+------------------------------------------
+
+The Unicam block on BCM283x SoCs is the receiver for either
+CSI-2 or CCP2 data from image sensors or similar devices.
+
+The main platform using this SoC is the Raspberry Pi family of boards.
+On the Pi the VideoCore firmware can also control this hardware block,
+and driving it from two different processors will cause issues.
+To avoid this, the firmware checks the device tree configuration
+during boot. If it finds device tree nodes called csi0 or csi1 then
+it will stop the firmware accessing the block, and it can then
+safely be used via the device tree binding.
+
+Required properties:
+===================
+- compatible	: must be "brcm,bcm2835-unicam".
+- reg		: physical base address and length of the register sets for the
+		  device.
+- interrupts	: should contain the IRQ line for this Unicam instance.
+- clocks	: list of clock specifiers, corresponding to entries in
+		  clock-names property.
+- clock-names	: must contain "lp" and "vpu" entries, matching entries in the
+		  clocks property.
+
+Unicam supports a single port node. It should contain one 'port' child node
+with child 'endpoint' node. Please refer to the bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Within the endpoint node the "remote-endpoint" and "data-lanes" properties
+are mandatory.
+Data lane reordering is not supported so the data lanes must be in order,
+starting at 1. The number of data lanes should represent the number of
+usable lanes for the hardware block. That may be limited by either the SoC or
+how the platform presents the interface, and the lower value must be used.
+
+Lane reordering is not supported on the clock lane either, so the optional
+property "clock-lane" will implicitly be <0>.
+Similarly lane inversion is not supported, therefore "lane-polarities" will
+implicitly be <0 0 0 0 0>.
+Neither of these values will be checked.
+
+Example:
+	csi1: csi1@7e801000 {
+		compatible = "brcm,bcm2835-unicam";
+		reg = <0x7e801000 0x800>,
+		      <0x7e802004 0x4>;
+		interrupts = <2 7>;
+		clocks = <&clocks BCM2835_CLOCK_CAM1>,
+			 <&firmware_clocks 4>;
+		clock-names = "lp", "vpu";
+		port {
+			csi1_ep: endpoint {
+				remote-endpoint = <&tc358743_0>;
+				data-lanes = <1 2>;
+			};
+		};
+	};
+
+	i2c0: i2c@7e205000 {
+		tc358743: csi-hdmi-bridge@0f {
+			compatible = "toshiba,tc358743";
+			reg = <0x0f>;
+
+			clocks = <&tc358743_clk>;
+			clock-names = "refclk";
+
+			tc358743_clk: bridge-clk {
+				compatible = "fixed-clock";
+				#clock-cells = <0>;
+				clock-frequency = <27000000>;
+			};
+
+			port {
+				tc358743_0: endpoint {
+					remote-endpoint = <&csi1_ep>;
+					clock-lanes = <0>;
+					data-lanes = <1 2>;
+					clock-noncontinuous;
+					link-frequencies =
+						/bits/ 64 <297000000>;
+				};
+			};
+		};
+	};

Documentation/devicetree/bindings/media/i2c/imx219.yaml

@@ -0,0 +1,114 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/imx219.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Sony 1/4.0-Inch 8Mpixel CMOS Digital Image Sensor
+
+maintainers:
+  - Dave Stevenson <dave.stevenson@raspberrypi.com>
+
+description: |-
+  The Sony imx219 is a 1/4.0-inch CMOS active pixel digital image sensor
+  with an active array size of 3280H x 2464V. It is programmable through
+  I2C interface. The I2C address is fixed to 0x10 as per sensor data sheet.
+  Image data is sent through MIPI CSI-2, which is configured as either 2 or
+  4 data lanes.
+
+properties:
+  compatible:
+    const: sony,imx219
+
+  reg:
+    description: I2C device address
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  VDIG-supply:
+    description:
+      Digital I/O voltage supply, 1.8 volts
+
+  VANA-supply:
+    description:
+      Analog voltage supply, 2.8 volts
+
+  VDDL-supply:
+    description:
+      Digital core voltage supply, 1.2 volts
+
+  reset-gpios:
+    description: |-
+      Reference to the GPIO connected to the xclr pin, if any.
+      Must be released (set high) after all supplies are applied.
+
+  # See ../video-interfaces.txt for more details
+  port:
+    type: object
+    properties:
+      endpoint:
+        type: object
+        properties:
+          data-lanes:
+            description: |-
+              The sensor supports either two-lane, or four-lane operation.
+              If this property is omitted four-lane operation is assumed.
+              For two-lane operation the property must be set to <1 2>.
+            items:
+              - const: 1
+              - const: 2
+
+          clock-noncontinuous:
+            type: boolean
+            description: |-
+              MIPI CSI-2 clock is non-continuous if this property is present,
+              otherwise it's continuous.
+
+          link-frequencies:
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint64-array
+            description:
+              Allowed data bus frequencies.
+
+        required:
+          - link-frequencies
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - VANA-supply
+  - VDIG-supply
+  - VDDL-supply
+  - port
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c0 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        imx219: sensor@10 {
+            compatible = "sony,imx219";
+            reg = <0x10>;
+            clocks = <&imx219_clk>;
+            VANA-supply = <&imx219_vana>;   /* 2.8v */
+            VDIG-supply = <&imx219_vdig>;   /* 1.8v */
+            VDDL-supply = <&imx219_vddl>;   /* 1.2v */
+
+            port {
+                imx219_0: endpoint {
+                    remote-endpoint = <&csi1_ep>;
+                    data-lanes = <1 2>;
+                    clock-noncontinuous;
+                    link-frequencies = /bits/ 64 <456000000>;
+                };
+            };
+        };
+    };
+
+...

Documentation/devicetree/bindings/media/i2c/imx290.txt

@@ -0,0 +1,58 @@
+* Sony IMX290 1/2.8-Inch CMOS Image Sensor
+
+The Sony IMX290 is a 1/2.8-Inch CMOS Solid-state image sensor with
+Square Pixel for Color or Monochrome Cameras. It is programmable through I2C
+and 4-wire interfaces.
+The sensor output is available via CMOS logic parallel SDR output,
+Low voltage LVDS DDR output and CSI-2 serial data output. The CSI-2 bus is the
+default. No bindings have been defined for the other busses.
+
+Required Properties:
+- compatible: Should be "sony,imx290", or "sony,imx290-mono"
+- reg: I2C bus address of the device
+- clocks: Reference to the xclk clock.
+- clock-names: Should be "xclk".
+- clock-frequency: Frequency of the xclk clock in Hz.
+- vdddo-supply: Sensor digital IO regulator.
+- vdda-supply: Sensor analog regulator.
+- vddd-supply: Sensor digital core regulator.
+
+Optional Properties:
+- reset-gpios: Sensor reset GPIO
+
+The imx290 device node should contain one 'port' child node with
+an 'endpoint' subnode. For further reading on port node refer to
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Required Properties on endpoint:
+- data-lanes: check ../video-interfaces.txt
+- link-frequencies: check ../video-interfaces.txt
+- remote-endpoint: check ../video-interfaces.txt
+
+Example:
+	&i2c1 {
+		...
+		imx290: camera-sensor@1a {
+			compatible = "sony,imx290";
+			reg = <0x1a>;
+
+			reset-gpios = <&msmgpio 35 GPIO_ACTIVE_LOW>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&camera_rear_default>;
+
+			clocks = <&gcc GCC_CAMSS_MCLK0_CLK>;
+			clock-names = "xclk";
+			clock-frequency = <37125000>;
+
+			vdddo-supply = <&camera_vdddo_1v8>;
+			vdda-supply = <&camera_vdda_2v8>;
+			vddd-supply = <&camera_vddd_1v5>;
+
+			port {
+				imx290_ep: endpoint {
+					data-lanes = <1 2 3 4>;
+					link-frequencies = /bits/ 64 <445500000>;
+					remote-endpoint = <&csiphy0_ep>;
+				};
+			};
+		};

Documentation/devicetree/bindings/media/i2c/imx477.yaml

@@ -0,0 +1,113 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/imx477.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Sony 1/2.3-Inch 12Mpixel CMOS Digital Image Sensor
+
+maintainers:
+  - Naushir Patuck <naush@raspberypi.com>
+
+description: |-
+  The Sony IMX477 is a 1/2.3-inch CMOS active pixel digital image sensor
+  with an active array size of 4056H x 3040V. It is programmable through
+  I2C interface. The I2C address is fixed to 0x1A as per sensor data sheet.
+  Image data is sent through MIPI CSI-2, which is configured as either 2 or
+  4 data lanes.
+
+properties:
+  compatible:
+    const: sony,imx477
+
+  reg:
+    description: I2C device address
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  VDIG-supply:
+    description:
+      Digital I/O voltage supply, 1.05 volts
+
+  VANA-supply:
+    description:
+      Analog voltage supply, 2.8 volts
+
+  VDDL-supply:
+    description:
+      Digital core voltage supply, 1.8 volts
+
+  reset-gpios:
+    description: |-
+      Reference to the GPIO connected to the xclr pin, if any.
+      Must be released (set high) after all all supplies and INCK are applied.
+
+  # See ../video-interfaces.txt for more details
+  port:
+    type: object
+    properties:
+      endpoint:
+        type: object
+        properties:
+          data-lanes:
+            description: |-
+              The sensor supports either two-lane, or four-lane operation.
+              For two-lane operation the property must be set to <1 2>.
+            items:
+              - const: 1
+              - const: 2
+
+          clock-noncontinuous:
+            type: boolean
+            description: |-
+              MIPI CSI-2 clock is non-continuous if this property is present,
+              otherwise it's continuous.
+
+          link-frequencies:
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint64-array
+            description:
+              Allowed data bus frequencies.
+
+        required:
+          - link-frequencies
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - VANA-supply
+  - VDIG-supply
+  - VDDL-supply
+  - port
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c0 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        imx477: sensor@10 {
+            compatible = "sony,imx477";
+            reg = <0x1a>;
+            clocks = <&imx477_clk>;
+            VANA-supply = <&imx477_vana>;   /* 2.8v */
+            VDIG-supply = <&imx477_vdig>;   /* 1.05v */
+            VDDL-supply = <&imx477_vddl>;   /* 1.8v */
+
+            port {
+                imx477_0: endpoint {
+                    remote-endpoint = <&csi1_ep>;
+                    data-lanes = <1 2>;
+                    clock-noncontinuous;
+                    link-frequencies = /bits/ 64 <450000000>;
+                };
+            };
+        };
+    };
+
+...

Documentation/devicetree/bindings/media/i2c/irs1125.txt

@@ -0,0 +1,48 @@
+* Infineon irs1125 time of flight sensor
+
+The Infineon irs1125 is a time of flight digital image sensor with
+an active array size of 352H x 286V. It is programmable through I2C
+interface. The I2C address defaults to 0x3D, but can be reconfigured
+to address 0x3C or 0x41 via I2C commands. Image data is sent through
+MIPI CSI-2, which is configured as either 1 or 2 data lanes.
+
+Required Properties:
+- compatible: value should be "infineon,irs1125" for irs1125 sensor
+- reg: I2C bus address of the device
+- clocks: reference to the xclk input clock.
+- pwdn-gpios: reference to the GPIO connected to the reset pin.
+	      This is an active low signal to the iirs1125.
+
+The irs1125 device node should contain one 'port' child node with
+an 'endpoint' subnode. For further reading on port node refer to
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Endpoint node required properties for CSI-2 connection are:
+- remote-endpoint: a phandle to the bus receiver's endpoint node.
+- clock-lanes: should be set to <0> (clock lane on hardware lane 0)
+- data-lanes: should be set to <1> or <1 2> (one or two lane CSI-2
+  supported)
+
+Example:
+	sensor@10 {
+		compatible = "infineon,irs1125";
+		reg = <0x3D>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&irs1125_clk>;
+		pwdn-gpios = <&gpio 5 0>;
+
+		irs1125_clk: camera-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <26000000>;
+		};
+
+		port {
+			sensor_out: endpoint {
+				remote-endpoint = <&csiss_in>;
+				clock-lanes = <0>;
+				data-lanes = <1 2>;
+			};
+		};
+	};

Documentation/devicetree/bindings/media/i2c/ov5647.txt

@@ -10,6 +10,9 @@ Required properties:
 - reg			: I2C slave address of the sensor.
 - clocks		: Reference to the xclk clock.
 
+Optional Properties:
+- pwdn-gpios: reference to the GPIO connected to the pwdn pin, if any.
+
 The common video interfaces bindings (see video-interfaces.txt) should be
 used to specify link to the image data receiver. The OV5647 device
 node should contain one 'port' child node with an 'endpoint' subnode.
@@ -26,6 +29,7 @@ Example:
 			compatible = "ovti,ov5647";
 			reg = <0x36>;
 			clocks = <&camera_clk>;
+			pwdn-gpios = <&pioE 29 GPIO_ACTIVE_HIGH>;
 			port {
 				camera_1: endpoint {
 					remote-endpoint = <&csi1_ep1>;

Documentation/devicetree/bindings/media/rpivid_hevc.yaml

@@ -0,0 +1,72 @@
+# SPDX-License-Identifier: GPL-2.0-only
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/rpivid_hevc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Raspberry Pi HEVC Decoder
+
+maintainers:
+  - Raspberry Pi <kernel-list@raspberrypi.com>
+
+description: |-
+  The Camera Adaptation Layer (CAL) is a key component for image capture
+  applications. The capture module provides the system interface and the
+  processing capability to connect CSI2 image-sensor modules to the
+  DRA72x device.
+
+properties:
+  compatible:
+    enum:
+      - raspberrypi,rpivid-vid-decoder
+
+  reg:
+    minItems: 2
+    items:
+      - description: The HEVC main register region
+      - description: The Interrupt controller register region
+
+  reg-names:
+    minItems: 2
+    items:
+      - const: hevc
+      - const: intc
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: The HEVC block clock
+
+  clock-names:
+    items:
+      - const: hevc
+
+required:
+  - compatible
+  - reg
+  - reg-names
+  - interrupts
+  - clocks
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+    video-codec@7eb10000 {
+        compatible = "raspberrypi,rpivid-vid-decoder";
+        reg = <0x0 0x7eb10000 0x1000>,	/* INTC */
+              <0x0 0x7eb00000 0x10000>; /* HEVC */
+        reg-names = "intc",
+                    "hevc";
+
+        interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+
+        clocks = <&clk 0>;
+        clock-names = "hevc";
+    };
+
+...

Documentation/devicetree/bindings/media/video-interfaces.txt

@@ -85,10 +85,374 @@ Optional properties
 
 - lens-focus: A phandle to the node of the focus lens controller.
 
-- rotation: The device, typically an image sensor, is not mounted upright,
-  but a number of degrees counter clockwise. Typical values are 0 and 180
-  (upside down).
+- rotation: The camera rotation is expressed as the angular difference in
+  degrees between two reference systems, one relative to the camera module, and
+  one defined on the external world scene to be captured when projected on the
+  image sensor pixel array.
 
+  A camera sensor has a 2-dimensional reference system 'Rc' defined by
+  its pixel array read-out order. The origin is set to the first pixel
+  being read out, the X-axis points along the column read-out direction
+  towards the last columns, and the Y-axis along the row read-out
+  direction towards the last row.
+
+  A typical example for a sensor with a 2592x1944 pixel array matrix
+  observed from the front is:
+
+              2591       X-axis          0
+                <------------------------+ 0
+                .......... ... ..........!
+                .......... ... ..........! Y-axis
+                           ...           !
+                .......... ... ..........!
+                .......... ... ..........! 1943
+                                         V
+
+  The external world scene reference system 'Rs' is a 2-dimensional
+  reference system on the focal plane of the camera module. The origin is
+  placed on the top-left corner of the visible scene, the X-axis points
+  towards the right, and the Y-axis points towards the bottom of the
+  scene. The top, bottom, left and right directions are intentionally not
+  defined and depend on the environment in which the camera is used.
+
+  A typical example of a (very common) picture of a shark swimming from
+  left to right, as seen from the camera, is:
+
+               0               X-axis
+             0 +------------------------------------->
+               !
+               !
+               !
+               !           |\____)\___
+               !           ) _____  __`<
+               !           |/     )/
+               !
+               !
+               !
+               V
+             Y-axis
+
+  with the reference system 'Rs' placed on the camera focal plane:
+
+                                  ¸.·˙!
+                              ¸.·˙    !
+                  _       ¸.·˙        !
+               +-/ \-+¸.·˙            !
+               | (o) |                ! Camera focal plane
+               +-----+˙·.¸            !
+                          ˙·.¸        !
+                              ˙·.¸    !
+                                  ˙·.¸!
+
+  When projected on the sensor's pixel array, the image and the associated
+  reference system 'Rs' are typically (but not always) inverted, due to
+  the camera module's lens optical inversion effect.
+
+  Assuming the above represented scene of the swimming shark, the lens
+  inversion projects the scene and its reference system onto the sensor
+  pixel array, seen from the front of the camera sensor, as follows:
+
+            Y-axis
+               ^
+               !
+               !
+               !
+               !            |\_____)\__
+               !            ) ____  ___.<
+               !            |/    )/
+               !
+               !
+               !
+             0 +------------------------------------->
+               0               X-axis
+
+  Note the shark being upside-down.
+
+  The resulting projected reference system is named 'Rp'.
+
+  The camera rotation property is then defined as the angular difference
+  in the counter-clockwise direction between the camera reference system
+  'Rc' and the projected scene reference system 'Rp'. It is expressed in
+  degrees as a number in the range [0, 360[.
+
+  Examples
+
+  0 degrees camera rotation:
+
+
+                    Y-Rp
+                     ^
+              Y-Rc   !
+               ^     !
+               !     !
+               !     !
+               !     !
+               !     !
+               !     !
+               !     !
+               !     !
+               !   0 +------------------------------------->
+               !     0               X-Rp
+             0 +------------------------------------->
+               0               X-Rc
+
+
+                                X-Rc                0
+               <------------------------------------+ 0
+                           X-Rp                 0   !
+           <------------------------------------+ 0 !
+                                                !   !
+                                                !   !
+                                                !   !
+                                                !   !
+                                                !   !
+                                                !   !
+                                                !   !
+                                                !   V
+                                                !  Y-Rc
+                                                V
+                                               Y-Rp
+
+  90 degrees camera rotation:
+
+               0        Y-Rc
+             0 +-------------------->
+               !   Y-Rp
+               !    ^
+               !    !
+               !    !
+               !    !
+               !    !
+               !    !
+               !    !
+               !    !
+               !    !
+               !    !
+               !  0 +------------------------------------->
+               !    0              X-Rp
+               !
+               !
+               !
+               !
+               V
+              X-Rc
+
+  180 degrees camera rotation:
+
+                                            0
+       <------------------------------------+ 0
+                        X-Rc                !
+              Y-Rp                          !
+               ^                            !
+               !                            !
+               !                            !
+               !                            !
+               !                            !
+               !                            !
+               !                            !
+               !                            V
+               !                           Y-Rc
+             0 +------------------------------------->
+               0              X-Rp
+
+  270 degrees camera rotation:
+
+               0        Y-Rc
+             0 +-------------------->
+               !                                        0
+               !    <-----------------------------------+ 0
+               !                    X-Rp                !
+               !                                        !
+               !                                        !
+               !                                        !
+               !                                        !
+               !                                        !
+               !                                        !
+               !                                        !
+               !                                        !
+               !                                        V
+               !                                       Y-Rp
+               !
+               !
+               !
+               !
+               V
+              X-Rc
+
+
+  Example one - Webcam
+
+  A camera module installed on the user facing part of a laptop screen
+  casing used for video calls. The captured images are meant to be
+  displayed in landscape mode (width > height) on the laptop screen.
+
+  The camera is typically mounted upside-down to compensate the lens
+  optical inversion effect:
+
+                    Y-Rp
+              Y-Rc   ^
+               ^     !
+               !     !
+               !     !       |\_____)\__
+               !     !       ) ____  ___.<
+               !     !       |/    )/
+               !     !
+               !     !
+               !     !
+               !   0 +------------------------------------->
+               !     0           X-Rp
+             0 +------------------------------------->
+               0            X-Rc
+
+  The two reference systems are aligned, the resulting camera rotation is
+  0 degrees, no rotation correction needs to be applied to the resulting
+  image once captured to memory buffers to correctly display it to users:
+
+               +--------------------------------------+
+               !                                      !
+               !                                      !
+               !                                      !
+               !             |\____)\___              !
+               !             ) _____  __`<            !
+               !             |/     )/                !
+               !                                      !
+               !                                      !
+               !                                      !
+               +--------------------------------------+
+
+  If the camera sensor is not mounted upside-down to compensate for the
+  lens optical inversion, the two reference systems will not be aligned,
+  with 'Rp' being rotated 180 degrees relatively to 'Rc':
+
+
+                        X-Rc                0
+       <------------------------------------+ 0
+                                            !
+              Y-Rp                          !
+               ^                            !
+               !                            !
+               !       |\_____)\__          !
+               !       ) ____  ___.<        !
+               !       |/    )/             !
+               !                            !
+               !                            !
+               !                            V
+               !                           Y-Rc
+             0 +------------------------------------->
+               0            X-Rp
+
+  The image once captured to memory will then be rotated by 180 degrees:
+
+               +--------------------------------------+
+               !                                      !
+               !                                      !
+               !                                      !
+               !              __/(_____/|             !
+               !            >.___  ____ (             !
+               !                 \(    \|             !
+               !                                      !
+               !                                      !
+               !                                      !
+               +--------------------------------------+
+
+  A software rotation correction of 180 degrees should be applied to
+  correctly display the image:
+
+               +--------------------------------------+
+               !                                      !
+               !                                      !
+               !                                      !
+               !             |\____)\___              !
+               !             ) _____  __`<            !
+               !             |/     )/                !
+               !                                      !
+               !                                      !
+               !                                      !
+               +--------------------------------------+
+
+  Example two - Phone camera
+
+  A camera installed on the back side of a mobile device facing away from
+  the user. The captured images are meant to be displayed in portrait mode
+  (height > width) to match the device screen orientation and the device
+  usage orientation used when taking the picture.
+
+  The camera sensor is typically mounted with its pixel array longer side
+  aligned to the device longer side, upside-down mounted to compensate for
+  the lens optical inversion effect:
+
+               0        Y-Rc
+             0 +-------------------->
+               !   Y-Rp
+               !    ^
+               !    !
+               !    !
+               !    !
+               !    !            |\_____)\__
+               !    !            ) ____  ___.<
+               !    !            |/    )/
+               !    !
+               !    !
+               !    !
+               !  0 +------------------------------------->
+               !    0                X-Rp
+               !
+               !
+               !
+               !
+               V
+              X-Rc
+
+  The two reference systems are not aligned and the 'Rp' reference
+  system is rotated by 90 degrees in the counter-clockwise direction
+  relatively to the 'Rc' reference system.
+
+  The image once captured to memory will be rotated:
+
+               +-------------------------------------+
+               |                 _ _                 |
+               |                \   /                |
+               |                 | |                 |
+               |                 | |                 |
+               |                 |  >                |
+               |                <  |                 |
+               |                 | |                 |
+               |                   .                 |
+               |                  V                  |
+               +-------------------------------------+
+
+  A correction of 90 degrees in counter-clockwise direction has to be
+  applied to correctly display the image in portrait mode on the device
+  screen:
+
+                        +--------------------+
+                        |                    |
+                        |                    |
+                        |                    |
+                        |                    |
+                        |                    |
+                        |                    |
+                        |   |\____)\___      |
+                        |   ) _____  __`<    |
+                        |   |/     )/        |
+                        |                    |
+                        |                    |
+                        |                    |
+                        |                    |
+                        |                    |
+                        +--------------------+
+
+- orientation: The orientation of a device (typically an image sensor or a flash
+  LED) describing its mounting position relative to the usage orientation of the
+  system where the device is installed on.
+  Possible values are:
+  0 - Front. The device is mounted on the front facing side of the system.
+  For mobile devices such as smartphones, tablets and laptops the front side is
+  the user facing side.
+  1 - Back. The device is mounted on the back side of the system, which is
+  defined as the opposite side of the front facing one.
+  2 - External. The device is not attached directly to the system but is
+  attached in a way that allows it to move freely.
 
 Optional endpoint properties
 ----------------------------

Documentation/devicetree/bindings/misc/brcm,bcm2835-smi-dev.txt

@@ -0,0 +1,17 @@
+* Broadcom BCM2835 SMI character device driver.
+
+SMI or secondary memory interface is a peripheral specific to certain Broadcom
+SOCs, and is helpful for talking to things like parallel-interface displays
+and NAND flashes (in fact, most things with a parallel register interface).
+
+This driver adds a character device which provides a user-space interface to
+an instance of the SMI driver.
+
+Required properties:
+- compatible: "brcm,bcm2835-smi-dev"
+- smi_handle: a phandle to the smi node.
+
+Optional properties:
+- None.
+
+

Documentation/devicetree/bindings/misc/brcm,bcm2835-smi.txt

@@ -0,0 +1,48 @@
+* Broadcom BCM2835 SMI driver.
+
+SMI or secondary memory interface is a peripheral specific to certain Broadcom
+SOCs, and is helpful for talking to things like parallel-interface displays
+and NAND flashes (in fact, most things with a parallel register interface).
+
+Required properties:
+- compatible: "brcm,bcm2835-smi"
+- reg: Should contain location and length of SMI registers and SMI clkman regs
+- interrupts: *the* SMI interrupt.
+- pinctrl-names: should be "default".
+- pinctrl-0: the phandle of the gpio pin node.
+- brcm,smi-clock-source: the clock source for clkman
+- brcm,smi-clock-divisor: the integer clock divisor for clkman
+- dmas: the dma controller phandle and the DREQ number (4 on a 2835)
+- dma-names: the name used by the driver to request its channel.
+  Should be "rx-tx".
+
+Optional properties:
+- None.
+
+Examples:
+
+8 data pin configuration:
+
+smi: smi@7e600000 {
+	compatible = "brcm,bcm2835-smi";
+	reg = <0x7e600000 0x44>, <0x7e1010b0 0x8>;
+	interrupts = <2 16>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&smi_pins>;
+	brcm,smi-clock-source = <6>;
+	brcm,smi-clock-divisor = <4>;
+	dmas = <&dma 4>;
+	dma-names = "rx-tx";
+
+	status = "okay";
+};
+
+smi_pins: smi_pins {
+	brcm,pins = <2 3 4 5 6 7 8 9 10 11 12 13 14 15>;
+	/* Alt 1: SMI */
+	brcm,function = <5 5 5 5 5 5 5 5 5 5 5 5 5 5>;
+	/* /CS, /WE and /OE are pulled high, as they are
+	   generally active low signals */
+	brcm,pull = <2 2 2 2 2 2 0 0 0 0 0 0 0 0>;
+};
+

Documentation/devicetree/bindings/net/microchip,lan78xx.txt

@@ -14,6 +14,9 @@ Optional properties of the embedded PHY:
 - microchip,led-modes: a 0..4 element vector, with each element configuring
   the operating mode of an LED. Omitted LEDs are turned off. Allowed values
   are defined in "include/dt-bindings/net/microchip-lan78xx.h".
+- microchip,downshift-after: sets the number of failed auto-negotiation
+  attempts after which the link is downgraded from 1000BASE-T. Should be one of
+  2, 3, 4, 5 or 0, where 0 means never downshift.
 
 Example:
 

Documentation/devicetree/bindings/pci/brcmstb-pcie.txt

@@ -0,0 +1,59 @@
+Brcmstb PCIe Host Controller Device Tree Bindings
+
+Required Properties:
+- compatible
+  "brcm,bcm7425-pcie" -- for 7425 family MIPS-based SOCs.
+  "brcm,bcm7435-pcie" -- for 7435 family MIPS-based SOCs.
+  "brcm,bcm7445-pcie" -- for 7445 and later ARM based SOCs (not including
+      the 7278).
+  "brcm,bcm7278-pcie"  -- for 7278 family ARM-based SOCs.
+
+- reg -- the register start address and length for the PCIe reg block.
+- interrupts -- two interrupts are specified; the first interrupt is for
+     the PCI host controller and the second is for MSI if the built-in
+     MSI controller is to be used.
+- interrupt-names -- names of the interrupts (above): "pcie" and "msi".
+- #address-cells -- set to <3>.
+- #size-cells -- set to <2>.
+- #interrupt-cells: set to <1>.
+- interrupt-map-mask and interrupt-map, standard PCI properties to define the
+     mapping of the PCIe interface to interrupt numbers.
+- ranges: ranges for the PCI memory and I/O regions.
+- linux,pci-domain -- should be unique per host controller.
+
+Optional Properties:
+- clocks -- phandle of pcie clock.
+- clock-names -- set to "sw_pcie" if clocks is used.
+- dma-ranges -- Specifies the inbound memory mapping regions when
+     an "identity map" is not possible.
+- msi-controller -- this property is typically specified to have the
+     PCIe controller use its internal MSI controller.
+- msi-parent -- set to use an external MSI interrupt controller.
+- brcm,enable-ssc -- (boolean) indicates usage of spread-spectrum clocking.
+- max-link-speed --  (integer) indicates desired generation of link:
+     1 => 2.5 Gbps (gen1), 2 => 5.0 Gbps (gen2), 3 => 8.0 Gbps (gen3).
+
+Example Node:
+
+pcie0: pcie@f0460000 {
+		reg = <0x0 0xf0460000 0x0 0x9310>;
+		interrupts = <0x0 0x0 0x4>;
+		compatible = "brcm,bcm7445-pcie";
+		#address-cells = <3>;
+		#size-cells = <2>;
+		ranges = <0x02000000 0x00000000 0x00000000 0x00000000 0xc0000000 0x00000000 0x08000000
+			  0x02000000 0x00000000 0x08000000 0x00000000 0xc8000000 0x00000000 0x08000000>;
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 7>;
+		interrupt-map = <0 0 0 1 &intc 0 47 3
+				 0 0 0 2 &intc 0 48 3
+				 0 0 0 3 &intc 0 49 3
+				 0 0 0 4 &intc 0 50 3>;
+		clocks = <&sw_pcie0>;
+		clock-names = "sw_pcie";
+		msi-parent = <&pcie0>;  /* use PCIe's internal MSI controller */
+		msi-controller;         /* use PCIe's internal MSI controller */
+		brcm,ssc;
+		max-link-speed = <1>;
+		linux,pci-domain = <0>;
+	};

Documentation/devicetree/bindings/power/reset/gpio-poweroff.txt

@@ -31,6 +31,7 @@ Optional properties:
 - inactive-delay-ms: Delay (default 100) to wait after driving gpio inactive
 - timeout-ms: Time to wait before asserting a WARN_ON(1). If nothing is
               specified, 3000 ms is used.
+- export : Export the GPIO line to the sysfs system
 
 Examples:
 

Documentation/devicetree/bindings/serial/pl011.yaml

@@ -100,6 +100,12 @@ properties:
       - $ref: /schemas/types.yaml#/definitions/uint32
       - default: 3000
 
+  cts-event-workaround:
+    description:
+      Enables the (otherwise vendor-specific) workaround for the
+      CTS-induced TX lockup.
+    type: boolean
+
 required:
   - compatible
   - reg

Documentation/devicetree/bindings/thermal/brcm,avs-ro-thermal.yaml

@@ -0,0 +1,45 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/thermal/brcm,avs-ro-thermal.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Broadcom AVS ring oscillator thermal
+
+maintainers:
+  - Stefan Wahren <wahrenst@gmx.net>
+
+description: |+
+  The thermal node should be the child of a syscon node with the
+  required property:
+
+  - compatible: Should be one of the following:
+                "brcm,bcm2711-avs-monitor", "syscon", "simple-mfd"
+
+  Refer to the the bindings described in
+  Documentation/devicetree/bindings/mfd/syscon.txt
+
+properties:
+  compatible:
+    const: brcm,bcm2711-thermal
+
+  reg:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+
+examples:
+  - |
+        avs-monitor@7d5d2000 {
+                compatible = "brcm,bcm2711-avs-monitor",
+                             "syscon", "simple-mfd";
+                reg = <0x7d5d2000 0xf00>;
+
+                thermal: thermal {
+                        compatible = "brcm,bcm2711-thermal";
+                        #thermal-sensor-cells = <0>;
+                };
+        };
+...

Documentation/devicetree/bindings/vendor-prefixes.txt

@@ -0,0 +1,463 @@
+Device tree binding vendor prefix registry.  Keep list in alphabetical order.
+
+This isn't an exhaustive list, but you should add new prefixes to it before
+using them to avoid name-space collisions.
+
+abilis	Abilis Systems
+abracon	Abracon Corporation
+actions	Actions Semiconductor Co., Ltd.
+active-semi	Active-Semi International Inc
+ad	Avionic Design GmbH
+adafruit	Adafruit Industries, LLC
+adapteva	Adapteva, Inc.
+adaptrum	Adaptrum, Inc.
+adh	AD Holdings Plc.
+adi	Analog Devices, Inc.
+advantech	Advantech Corporation
+aeroflexgaisler	Aeroflex Gaisler AB
+al	Annapurna Labs
+allo	Allo.com
+allwinner	Allwinner Technology Co., Ltd.
+alphascale	AlphaScale Integrated Circuits Systems, Inc.
+altr	Altera Corp.
+amarula	Amarula Solutions
+amazon	Amazon.com, Inc.
+amcc	Applied Micro Circuits Corporation (APM, formally AMCC)
+amd	Advanced Micro Devices (AMD), Inc.
+amediatech	Shenzhen Amediatech Technology Co., Ltd
+amlogic	Amlogic, Inc.
+ampire	Ampire Co., Ltd.
+ams	AMS AG
+amstaos	AMS-Taos Inc.
+analogix	Analogix Semiconductor, Inc.
+andestech	Andes Technology Corporation
+apm	Applied Micro Circuits Corporation (APM)
+aptina	Aptina Imaging
+arasan	Arasan Chip Systems
+archermind ArcherMind Technology (Nanjing) Co., Ltd.
+arctic	Arctic Sand
+aries	Aries Embedded GmbH
+arm	ARM Ltd.
+armadeus	ARMadeus Systems SARL
+arrow	Arrow Electronics
+artesyn	Artesyn Embedded Technologies Inc.
+asahi-kasei	Asahi Kasei Corp.
+aspeed	ASPEED Technology Inc.
+asus	AsusTek Computer Inc.
+atlas	Atlas Scientific LLC
+atmel	Atmel Corporation
+auo	AU Optronics Corporation
+auvidea Auvidea GmbH
+avago	Avago Technologies
+avia	avia semiconductor
+avic	Shanghai AVIC Optoelectronics Co., Ltd.
+avnet	Avnet, Inc.
+axentia	Axentia Technologies AB
+axis	Axis Communications AB
+bananapi BIPAI KEJI LIMITED
+bhf	Beckhoff Automation GmbH & Co. KG
+bitmain	Bitmain Technologies
+blokaslabs	Vilniaus Blokas UAB
+boe	BOE Technology Group Co., Ltd.
+bosch	Bosch Sensortec GmbH
+boundary	Boundary Devices Inc.
+brcm	Broadcom Corporation
+buffalo	Buffalo, Inc.
+bticino Bticino International
+calxeda	Calxeda
+capella	Capella Microsystems, Inc
+cascoda	Cascoda, Ltd.
+catalyst	Catalyst Semiconductor, Inc.
+cavium	Cavium, Inc.
+cdns	Cadence Design Systems Inc.
+cdtech	CDTech(H.K.) Electronics Limited
+ceva	Ceva, Inc.
+chipidea	Chipidea, Inc
+chipone		ChipOne
+chipspark	ChipSPARK
+chrp	Common Hardware Reference Platform
+chunghwa	Chunghwa Picture Tubes Ltd.
+ciaa	Computadora Industrial Abierta Argentina
+cirrus	Cirrus Logic, Inc.
+cloudengines	Cloud Engines, Inc.
+cnm	Chips&Media, Inc.
+cnxt	Conexant Systems, Inc.
+compulab	CompuLab Ltd.
+cortina	Cortina Systems, Inc.
+cosmic	Cosmic Circuits
+crane	Crane Connectivity Solutions
+creative	Creative Technology Ltd
+crystalfontz	Crystalfontz America, Inc.
+csky	Hangzhou C-SKY Microsystems Co., Ltd
+cubietech	Cubietech, Ltd.
+cypress	Cypress Semiconductor Corporation
+cznic	CZ.NIC, z.s.p.o.
+dallas	Maxim Integrated Products (formerly Dallas Semiconductor)
+dataimage	DataImage, Inc.
+davicom	DAVICOM Semiconductor, Inc.
+delta	Delta Electronics, Inc.
+denx	Denx Software Engineering
+devantech	Devantech, Ltd.
+dh	DH electronics GmbH
+digi	Digi International Inc.
+digilent	Diglent, Inc.
+dioo	Dioo Microcircuit Co., Ltd
+dlc	DLC Display Co., Ltd.
+dlg	Dialog Semiconductor
+dlink	D-Link Corporation
+dmo	Data Modul AG
+domintech	Domintech Co., Ltd.
+dongwoon	Dongwoon Anatech
+dptechnics	DPTechnics
+dragino	Dragino Technology Co., Limited
+ea	Embedded Artists AB
+ebs-systart EBS-SYSTART GmbH
+ebv	EBV Elektronik
+eckelmann	Eckelmann AG
+edt	Emerging Display Technologies
+eeti	eGalax_eMPIA Technology Inc
+elan	Elan Microelectronic Corp.
+elgin	Elgin S/A.
+embest	Shenzhen Embest Technology Co., Ltd.
+emlid	Emlid, Ltd.
+emmicro	EM Microelectronic
+emtrion	emtrion GmbH
+endless	Endless Mobile, Inc.
+energymicro	Silicon Laboratories (formerly Energy Micro AS)
+engicam	Engicam S.r.l.
+epcos	EPCOS AG
+epfl	Ecole Polytechnique Fédérale de Lausanne
+epson	Seiko Epson Corp.
+est	ESTeem Wireless Modems
+ettus	NI Ettus Research
+eukrea  Eukréa Electromatique
+everest	Everest Semiconductor Co. Ltd.
+everspin	Everspin Technologies, Inc.
+exar	Exar Corporation
+excito	Excito
+ezchip	EZchip Semiconductor
+facebook	Facebook
+fairphone	Fairphone B.V.
+faraday	Faraday Technology Corporation
+fastrax	Fastrax Oy
+fcs	Fairchild Semiconductor
+feiyang	Shenzhen Fly Young Technology Co.,LTD.
+firefly	Firefly
+focaltech	FocalTech Systems Co.,Ltd
+friendlyarm	Guangzhou FriendlyARM Computer Tech Co., Ltd
+fsl	Freescale Semiconductor
+fujitsu	Fujitsu Ltd.
+gateworks	Gateworks Corporation
+gcw Game Consoles Worldwide
+ge	General Electric Company
+geekbuying	GeekBuying
+gef	GE Fanuc Intelligent Platforms Embedded Systems, Inc.
+GEFanuc	GE Fanuc Intelligent Platforms Embedded Systems, Inc.
+geniatech	Geniatech, Inc.
+giantec	Giantec Semiconductor, Inc.
+giantplus	Giantplus Technology Co., Ltd.
+globalscale	Globalscale Technologies, Inc.
+globaltop	GlobalTop Technology, Inc.
+gmt	Global Mixed-mode Technology, Inc.
+goodix	Shenzhen Huiding Technology Co., Ltd.
+google	Google, Inc.
+grinn	Grinn
+grmn	Garmin Limited
+gumstix	Gumstix, Inc.
+gw	Gateworks Corporation
+hannstar	HannStar Display Corporation
+haoyu	Haoyu Microelectronic Co. Ltd.
+hardkernel	Hardkernel Co., Ltd
+hideep	HiDeep Inc.
+himax	Himax Technologies, Inc.
+hisilicon	Hisilicon Limited.
+hit	Hitachi Ltd.
+hitex	Hitex Development Tools
+holt	Holt Integrated Circuits, Inc.
+honeywell	Honeywell
+hp	Hewlett Packard
+holtek	Holtek Semiconductor, Inc.
+hwacom	HwaCom Systems Inc.
+i2se	I2SE GmbH
+ibm	International Business Machines (IBM)
+icplus	IC Plus Corp.
+idt	Integrated Device Technologies, Inc.
+ifi	Ingenieurburo Fur Ic-Technologie (I/F/I)
+ilitek	ILI Technology Corporation (ILITEK)
+img	Imagination Technologies Ltd.
+infineon Infineon Technologies
+inforce	Inforce Computing
+ingenic	Ingenic Semiconductor
+innolux	Innolux Corporation
+inside-secure	INSIDE Secure
+intel	Intel Corporation
+intercontrol	Inter Control Group
+invensense	InvenSense Inc.
+inversepath	Inverse Path
+iom	Iomega Corporation
+isee	ISEE 2007 S.L.
+isil	Intersil
+issi	Integrated Silicon Solutions Inc.
+itead	ITEAD Intelligent Systems Co.Ltd
+iwave  iWave Systems Technologies Pvt. Ltd.
+jdi	Japan Display Inc.
+jedec	JEDEC Solid State Technology Association
+jianda	Jiandangjing Technology Co., Ltd.
+karo	Ka-Ro electronics GmbH
+keithkoep	Keith & Koep GmbH
+keymile	Keymile GmbH
+khadas	Khadas
+kiebackpeter    Kieback & Peter GmbH
+kinetic Kinetic Technologies
+kingdisplay	King & Display Technology Co., Ltd.
+kingnovel	Kingnovel Technology Co., Ltd.
+koe	Kaohsiung Opto-Electronics Inc.
+kosagi	Sutajio Ko-Usagi PTE Ltd.
+kyo	Kyocera Corporation
+lacie	LaCie
+laird	Laird PLC
+lantiq	Lantiq Semiconductor
+lattice	Lattice Semiconductor
+lego	LEGO Systems A/S
+lemaker	Shenzhen LeMaker Technology Co., Ltd.
+lenovo	Lenovo Group Ltd.
+lg	LG Corporation
+libretech	Shenzhen Libre Technology Co., Ltd
+licheepi	Lichee Pi
+linaro	Linaro Limited
+linksys	Belkin International, Inc. (Linksys)
+linux	Linux-specific binding
+linx	Linx Technologies
+lltc	Linear Technology Corporation
+logicpd	Logic PD, Inc.
+lsi	LSI Corp. (LSI Logic)
+lwn	Liebherr-Werk Nenzing GmbH
+macnica	Macnica Americas
+marvell	Marvell Technology Group Ltd.
+maxim	Maxim Integrated Products
+mbvl	Mobiveil Inc.
+mcube	mCube
+meas	Measurement Specialties
+mediatek	MediaTek Inc.
+megachips	MegaChips
+mele	Shenzhen MeLE Digital Technology Ltd.
+melexis	Melexis N.V.
+melfas	MELFAS Inc.
+mellanox	Mellanox Technologies
+memsic	MEMSIC Inc.
+merrii	Merrii Technology Co., Ltd.
+micrel	Micrel Inc.
+microchip	Microchip Technology Inc.
+microcrystal	Micro Crystal AG
+micron	Micron Technology Inc.
+mikroe		MikroElektronika d.o.o.
+minix	MINIX Technology Ltd.
+miramems	MiraMEMS Sensing Technology Co., Ltd.
+mitsubishi	Mitsubishi Electric Corporation
+mosaixtech	Mosaix Technologies, Inc.
+motorola	Motorola, Inc.
+moxa	Moxa Inc.
+mpl	MPL AG
+mqmaker	mqmaker Inc.
+mscc	Microsemi Corporation
+msi	Micro-Star International Co. Ltd.
+mti	Imagination Technologies Ltd. (formerly MIPS Technologies Inc.)
+multi-inno	Multi-Inno Technology Co.,Ltd
+mundoreader	Mundo Reader S.L.
+murata	Murata Manufacturing Co., Ltd.
+mxicy	Macronix International Co., Ltd.
+myir	MYIR Tech Limited
+national	National Semiconductor
+nec	NEC LCD Technologies, Ltd.
+neonode		Neonode Inc.
+netgear	NETGEAR
+netlogic	Broadcom Corporation (formerly NetLogic Microsystems)
+netron-dy	Netron DY
+netxeon		Shenzhen Netxeon Technology CO., LTD
+nexbox	Nexbox
+nextthing	Next Thing Co.
+newhaven	Newhaven Display International
+ni	National Instruments
+nintendo	Nintendo
+nlt	NLT Technologies, Ltd.
+nokia	Nokia
+nordic	Nordic Semiconductor
+novtech NovTech, Inc.
+nutsboard	NutsBoard
+nuvoton	Nuvoton Technology Corporation
+nvd	New Vision Display
+nvidia	NVIDIA
+nxp	NXP Semiconductors
+okaya	Okaya Electric America, Inc.
+oki	Oki Electric Industry Co., Ltd.
+olimex	OLIMEX Ltd.
+olpc	One Laptop Per Child
+onion	Onion Corporation
+onnn	ON Semiconductor Corp.
+ontat	On Tat Industrial Company
+opalkelly	Opal Kelly Incorporated
+opencores	OpenCores.org
+openrisc	OpenRISC.io
+option	Option NV
+oranth	Shenzhen Oranth Technology Co., Ltd.
+ORCL	Oracle Corporation
+orisetech	Orise Technology
+ortustech	Ortus Technology Co., Ltd.
+ovti	OmniVision Technologies
+oxsemi	Oxford Semiconductor, Ltd.
+panasonic	Panasonic Corporation
+parade	Parade Technologies Inc.
+pda	Precision Design Associates, Inc.
+pericom	Pericom Technology Inc.
+pervasive	Pervasive Displays, Inc.
+phicomm PHICOMM Co., Ltd.
+phytec	PHYTEC Messtechnik GmbH
+picochip	Picochip Ltd
+pine64	Pine64
+pixcir  PIXCIR MICROELECTRONICS Co., Ltd
+plantower Plantower Co., Ltd
+plathome	Plat'Home Co., Ltd.
+plda	PLDA
+plx	Broadcom Corporation (formerly PLX Technology)
+pni	PNI Sensor Corporation
+portwell	Portwell Inc.
+poslab	Poslab Technology Co., Ltd.
+powervr	PowerVR (deprecated, use img)
+probox2	PROBOX2 (by W2COMP Co., Ltd.)
+pulsedlight	PulsedLight, Inc
+qca	Qualcomm Atheros, Inc.
+qcom	Qualcomm Technologies, Inc
+qemu	QEMU, a generic and open source machine emulator and virtualizer
+qi	Qi Hardware
+qiaodian	QiaoDian XianShi Corporation
+qnap	QNAP Systems, Inc.
+radxa	Radxa
+raidsonic	RaidSonic Technology GmbH
+ralink	Mediatek/Ralink Technology Corp.
+ramtron	Ramtron International
+raspberrypi	Raspberry Pi Foundation
+raydium	Raydium Semiconductor Corp.
+rda	Unisoc Communications, Inc.
+realtek Realtek Semiconductor Corp.
+renesas	Renesas Electronics Corporation
+richtek	Richtek Technology Corporation
+ricoh	Ricoh Co. Ltd.
+rikomagic	Rikomagic Tech Corp. Ltd
+riscv	RISC-V Foundation
+rockchip	Fuzhou Rockchip Electronics Co., Ltd
+rohm	ROHM Semiconductor Co., Ltd
+roofull	Shenzhen Roofull Technology Co, Ltd
+samsung	Samsung Semiconductor
+samtec	Samtec/Softing company
+sancloud	Sancloud Ltd
+sandisk	Sandisk Corporation
+sbs	Smart Battery System
+schindler	Schindler
+seagate	Seagate Technology PLC
+semtech	Semtech Corporation
+sensirion	Sensirion AG
+sff	Small Form Factor Committee
+sgd	Solomon Goldentek Display Corporation
+sgx	SGX Sensortech
+sharp	Sharp Corporation
+shimafuji	Shimafuji Electric, Inc.
+si-en	Si-En Technology Ltd.
+sifive	SiFive, Inc.
+sigma	Sigma Designs, Inc.
+sii	Seiko Instruments, Inc.
+sil	Silicon Image
+silabs	Silicon Laboratories
+silead	Silead Inc.
+silergy	Silergy Corp.
+siliconmitus	Silicon Mitus, Inc.
+simtek
+sirf	SiRF Technology, Inc.
+sis	Silicon Integrated Systems Corp.
+sitronix	Sitronix Technology Corporation
+skyworks	Skyworks Solutions, Inc.
+smsc	Standard Microsystems Corporation
+snps	Synopsys, Inc.
+socionext	Socionext Inc.
+solidrun	SolidRun
+solomon        Solomon Systech Limited
+sony	Sony Corporation
+spansion	Spansion Inc.
+sprd	Spreadtrum Communications Inc.
+sst	Silicon Storage Technology, Inc.
+st	STMicroelectronics
+starry	Starry Electronic Technology (ShenZhen) Co., LTD
+startek	Startek
+ste	ST-Ericsson
+stericsson	ST-Ericsson
+summit	Summit microelectronics
+sunchip	Shenzhen Sunchip Technology Co., Ltd
+SUNW	Sun Microsystems, Inc
+swir	Sierra Wireless
+syna	Synaptics Inc.
+synology	Synology, Inc.
+tbs	TBS Technologies
+tbs-biometrics	Touchless Biometric Systems AG
+tcg	Trusted Computing Group
+tcl	Toby Churchill Ltd.
+technexion	TechNexion
+technologic	Technologic Systems
+tempo	Tempo Semiconductor
+techstar	Shenzhen Techstar Electronics Co., Ltd.
+terasic	Terasic Inc.
+thine	THine Electronics, Inc.
+ti	Texas Instruments
+tianma	Tianma Micro-electronics Co., Ltd.
+tlm	Trusted Logic Mobility
+tmt	Tecon Microprocessor Technologies, LLC.
+topeet  Topeet
+toradex	Toradex AG
+toshiba	Toshiba Corporation
+toumaz	Toumaz
+tpk	TPK U.S.A. LLC
+tplink	TP-LINK Technologies Co., Ltd.
+tpo	TPO
+tronfy	Tronfy
+tronsmart	Tronsmart
+truly	Truly Semiconductors Limited
+tsd	Theobroma Systems Design und Consulting GmbH
+tyan	Tyan Computer Corporation
+u-blox	u-blox
+ucrobotics	uCRobotics
+ubnt	Ubiquiti Networks
+udoo	Udoo
+uniwest	United Western Technologies Corp (UniWest)
+upisemi	uPI Semiconductor Corp.
+urt	United Radiant Technology Corporation
+usi	Universal Scientific Industrial Co., Ltd.
+v3	V3 Semiconductor
+vamrs	Vamrs Ltd.
+variscite	Variscite Ltd.
+via	VIA Technologies, Inc.
+virtio	Virtual I/O Device Specification, developed by the OASIS consortium
+vishay	Vishay Intertechnology, Inc
+vitesse	Vitesse Semiconductor Corporation
+vivante	Vivante Corporation
+vocore VoCore Studio
+voipac	Voipac Technologies s.r.o.
+vot	Vision Optical Technology Co., Ltd.
+wd	Western Digital Corp.
+wetek	WeTek Electronics, limited.
+wexler	Wexler
+whwave  Shenzhen whwave Electronics, Inc.
+wi2wi	Wi2Wi, Inc.
+winbond Winbond Electronics corp.
+winstar	Winstar Display Corp.
+wlf	Wolfson Microelectronics
+wm	Wondermedia Technologies, Inc.
+x-powers	X-Powers
+xes	Extreme Engineering Solutions (X-ES)
+xillybus	Xillybus Ltd.
+xlnx	Xilinx
+xunlong	Shenzhen Xunlong Software CO.,Limited
+ysoft	Y Soft Corporation a.s.
+zarlink	Zarlink Semiconductor
+zeitec	ZEITEC Semiconductor Co., LTD.
+zidoo	Shenzhen Zidoo Technology Co., Ltd.
+zii	Zodiac Inflight Innovations
+zte	ZTE Corp.
+zyxel	ZyXEL Communications Corp.

Documentation/devicetree/bindings/vendor-prefixes.yaml

@@ -143,6 +143,8 @@ patternProperties:
     description: Beckhoff Automation GmbH & Co. KG
   "^bitmain,.*":
     description: Bitmain Technologies
+  "^blokaslabs,.*":
+    description: Vilniaus Blokas UAB
   "^boe,.*":
     description: BOE Technology Group Co., Ltd.
   "^bosch,.*":

Documentation/devicetree/configfs-overlays.txt

@@ -0,0 +1,31 @@
+Howto use the configfs overlay interface.
+
+A device-tree configfs entry is created in /config/device-tree/overlays
+and and it is manipulated using standard file system I/O.
+Note that this is a debug level interface, for use by developers and
+not necessarily something accessed by normal users due to the
+security implications of having direct access to the kernel's device tree.
+
+* To create an overlay you mkdir the directory:
+
+	# mkdir /config/device-tree/overlays/foo
+
+* Either you echo the overlay firmware file to the path property file.
+
+	# echo foo.dtbo >/config/device-tree/overlays/foo/path
+
+* Or you cat the contents of the overlay to the dtbo file
+
+	# cat foo.dtbo >/config/device-tree/overlays/foo/dtbo
+
+The overlay file will be applied, and devices will be created/destroyed
+as required.
+
+To remove it simply rmdir the directory.
+
+	# rmdir /config/device-tree/overlays/foo
+
+The rationalle of the dual interface (firmware & direct copy) is that each is
+better suited to different use patterns. The firmware interface is what's
+intended to be used by hardware managers in the kernel, while the copy interface
+make sense for developers (since it avoids problems with namespaces).

Documentation/fb/modedb.rst

@@ -65,6 +65,9 @@ Valid options are::
   - reflect_y (boolean): Perform an axial symmetry on the Y axis
   - rotate (integer): Rotate the initial framebuffer by x
     degrees. Valid values are 0, 90, 180 and 270.
+  - panel_orientation, one of "normal", "upside_down", "left_side_up", or
+    "right_side_up". For KMS drivers only, this sets the "panel orientation"
+    property on the kms connector as hint for kms users.
 
 
 -----------------------------------------------------------------------------

Documentation/hwmon/rpi-poe-fan

@@ -0,0 +1,15 @@
+Kernel driver rpi-poe-fan
+=====================
+
+This driver enables the use of the Raspberry Pi PoE HAT fan.
+
+Author: Serge Schneider <serge@raspberrypi.org>
+
+Description
+-----------
+
+The driver implements a simple interface for driving the Raspberry Pi PoE
+(Power over Ethernet) HAT fan. The driver passes commands to the Raspberry Pi
+firmware through the mailbox property interface. The firmware then forwards
+the commands to the board over I2C on the ID_EEPROM pins. The driver exposes
+the fan to the user space through the hwmon sysfs interface.

Documentation/lzo.txt

@@ -159,11 +159,15 @@ Byte sequences
            distance = 16384 + (H << 14) + D
            state = S (copy S literals after this block)
            End of stream is reached if distance == 16384
+           In version 1 only, to prevent ambiguity with the RLE case when
+           ((distance & 0x803f) == 0x803f) && (261 <= length <= 264), the
+           compressor must not emit block copies where distance and length
+           meet these conditions.
 
         In version 1 only, this instruction is also used to encode a run of
-        zeros if distance = 0xbfff, i.e. H = 1 and the D bits are all 1.
+           zeros if distance = 0xbfff, i.e. H = 1 and the D bits are all 1.
            In this case, it is followed by a fourth byte, X.
-           run length = ((X << 3) | (0 0 0 0 0 L L L)) + 4.
+           run length = ((X << 3) | (0 0 0 0 0 L L L)) + 4
 
       0 0 1 L L L L L  (32..63)
            Copy of small block within 16kB distance (preferably less than 34B)

Documentation/media/kapi/v4l2-subdev.rst

@@ -275,8 +275,13 @@ system the .unbind() method is called. All three callbacks are optional.
 V4L2 sub-device userspace API
 -----------------------------
 
-Beside exposing a kernel API through the :c:type:`v4l2_subdev_ops` structure,
-V4L2 sub-devices can also be controlled directly by userspace applications.
+Bridge drivers traditionally expose one or multiple video nodes to userspace,
+and control subdevices through the :c:type:`v4l2_subdev_ops` operations in
+response to video node operations. This hides the complexity of the underlying
+hardware from applications. For complex devices, finer-grained control of the
+device than what the video nodes offer may be required. In those cases, bridge
+drivers that implement :ref:`the media controller API <media_controller>` may
+opt for making the subdevice operations directly accessible from userpace.
 
 Device nodes named ``v4l-subdev``\ *X* can be created in ``/dev`` to access
 sub-devices directly. If a sub-device supports direct userspace configuration
@@ -327,6 +332,50 @@ Private ioctls
 	All ioctls not in the above list are passed directly to the sub-device
 	driver through the core::ioctl operation.
 
+Read-only sub-device userspace API
+----------------------------------
+
+Bridge drivers that control their connected subdevices through direct calls to
+the kernel API realized by :c:type:`v4l2_subdev_ops` structure do not usually
+want userspace to be able to change the same parameters through the subdevice
+device node and thus do not usually register any.
+
+It is sometimes useful to report to userspace the current subdevice
+configuration through a read-only API, that does not permit applications to
+change to the device parameters but allows interfacing to the subdevice device
+node to inspect them.
+
+For instance, to implement cameras based on computational photography, userspace
+needs to know the detailed camera sensor configuration (in terms of skipping,
+binning, cropping and scaling) for each supported output resolution. To support
+such use cases, bridge drivers may expose the subdevice operations to userspace
+through a read-only API.
+
+To create a read-only device node for all the subdevices registered with the
+``V4L2_SUBDEV_FL_HAS_DEVNODE`` set, the :c:type:`v4l2_device` driver should call
+:c:func:`v4l2_device_register_ro_subdev_nodes`.
+
+Access to the following ioctls for userspace applications is restricted on
+sub-device device nodes registered with
+:c:func:`v4l2_device_register_ro_subdev_nodes`.
+
+``VIDIOC_SUBDEV_S_FMT``,
+``VIDIOC_SUBDEV_S_CROP``,
+``VIDIOC_SUBDEV_S_SELECTION``:
+
+	These ioctls are only allowed on a read-only subdevice device node
+	for the :ref:`V4L2_SUBDEV_FORMAT_TRY <v4l2-subdev-format-whence>`
+	formats and selection rectangles.
+
+``VIDIOC_SUBDEV_S_FRAME_INTERVAL``,
+``VIDIOC_SUBDEV_S_DV_TIMINGS``,
+``VIDIOC_SUBDEV_S_STD``:
+
+	These ioctls are not allowed on a read-only subdevice node.
+
+In case the ioctl is not allowed, or the format to modify is set to
+``V4L2_SUBDEV_FORMAT_ACTIVE``, the core returns a negative error code and
+the errno variable is set to ``-EPERM``.
 
 I2C sub-device drivers
 ----------------------

Documentation/media/uapi/v4l/biblio.rst

@@ -131,6 +131,15 @@ ITU-T Rec. H.264 Specification (04/2017 Edition)
 
 :author:    International Telecommunication Union (http://www.itu.ch)
 
+.. _hevc:
+
+ITU H.265/HEVC
+==============
+
+:title:     ITU-T Rec. H.265 | ISO/IEC 23008-2 "High Efficiency Video Coding"
+
+:author:    International Telecommunication Union (http://www.itu.ch), International Organisation for Standardisation (http://www.iso.ch)
+
 .. _jfif:
 
 JFIF

Documentation/media/uapi/v4l/buffer.rst

@@ -607,6 +607,19 @@ Buffer Flags
 	applications shall use this flag for output buffers if the data in
 	this buffer has not been created by the CPU but by some
 	DMA-capable unit, in which case caches have not been used.
+    * .. _`V4L2-BUF-FLAG-M2M-HOLD-CAPTURE-BUF`:
+
+      - ``V4L2_BUF_FLAG_M2M_HOLD_CAPTURE_BUF``
+      - 0x00000200
+      - Only valid if ``V4L2_BUF_CAP_SUPPORTS_M2M_HOLD_CAPTURE_BUF`` is
+	set. It is typically used with stateless decoders where multiple
+	output buffers each decode to a slice of the decoded frame.
+	Applications can set this flag when queueing the output buffer
+	to prevent the driver from dequeueing the capture buffer after
+	the output buffer has been decoded (i.e. the capture buffer is
+	'held'). If the timestamp of this output buffer differs from that
+	of the previous output buffer, then that indicates the start of a
+	new frame and the previously held capture buffer is dequeued.
     * .. _`V4L2-BUF-FLAG-LAST`:
 
       - ``V4L2_BUF_FLAG_LAST``

Documentation/media/uapi/v4l/dev-subdev.rst

@@ -39,6 +39,11 @@ will feature a character device node on which ioctls can be called to
 Sub-device character device nodes, conventionally named
 ``/dev/v4l-subdev*``, use major number 81.
 
+Drivers may opt to limit the sub-device character devices to only expose
+operations that do not modify the device state. In such a case the sub-devices
+are referred to as ``read-only`` in the rest of this documentation, and the
+related restrictions are documented in individual ioctls.
+
 
 Controls
 ========

Documentation/media/uapi/v4l/ext-ctrls-camera.rst

@@ -510,6 +510,157 @@ enum v4l2_scene_mode -
     value down. A value of zero stops the motion if one is in progress
     and has no effect otherwise.
 
+``V4L2_CID_CAMERA_ORIENTATION (menu)``
+    This read-only control describes the camera orientation by reporting its
+    mounting position on the device where the camera is installed. The control
+    value is constant and not modifiable by software. This control is
+    particularly meaningful for devices which have a well defined orientation,
+    such as phones, laptops and portable devices since the control is expressed
+    as a position relative to the device's intended usage orientation. For
+    example, a camera installed on the user-facing side of a phone, a tablet or
+    a laptop device is said to be have ``V4L2_CAMERA_ORIENTATION_FRONT``
+    orientation, while a camera installed on the opposite side of the front one
+    is said to be have ``V4L2_CAMERA_ORIENTATION_BACK`` orientation. Camera
+    sensors not directly attached to the device, or attached in a way that
+    allows them to move freely, such as webcams and digital cameras, are said to
+    have the ``V4L2_CAMERA_ORIENTATION_EXTERNAL`` orientation.
+
+
+
+.. flat-table::
+    :header-rows:  0
+    :stub-columns: 0
+
+    * - ``V4L2_CAMERA_ORIENTATION_FRONT``
+      - The camera is oriented towards the user facing side of the device.
+    * - ``V4L2_CAMERA_ORIENTATION_BACK``
+      - The camera is oriented towards the back facing side of the device.
+    * - ``V4L2_CAMERA_ORIENTATION_EXTERNAL``
+      - The camera is not directly attached to the device and is freely movable.
+
+
+
+``V4L2_CID_CAMERA_SENSOR_ROTATION (integer)``
+    This read-only control describes the rotation correction in degrees in the
+    counter-clockwise direction to be applied to the captured images once
+    captured to memory to compensate for the camera sensor mounting rotation.
+
+    For a precise definition of the sensor mounting rotation refer to the
+    extensive description of the 'rotation' properties in the device tree
+    bindings file 'video-interfaces.txt'.
+
+    A few examples are below reported, using a shark swimming from left to
+    right in front of the user as the example scene to capture. ::
+
+                 0               X-axis
+               0 +------------------------------------->
+                 !
+                 !
+                 !
+                 !           |\____)\___
+                 !           ) _____  __`<
+                 !           |/     )/
+                 !
+                 !
+                 !
+                 V
+               Y-axis
+
+    Example one - Webcam
+
+    Assuming you can bring your laptop with you while swimming with sharks,
+    the camera module of the laptop is installed on the user facing part of a
+    laptop screen casing, and is typically used for video calls. The captured
+    images are meant to be displayed in landscape mode (width > height) on the
+    laptop screen.
+
+    The camera is typically mounted upside-down to compensate the lens optical
+    inversion effect. In this case the value of the
+    V4L2_CID_CAMERA_SENSOR_ROTATION control is 0, no rotation is required to
+    display images correctly to the user.
+
+    If the camera sensor is not mounted upside-down it is required to compensate
+    the lens optical inversion effect and the value of the
+    V4L2_CID_CAMERA_SENSOR_ROTATION control is 180 degrees, as images will
+    result rotated when captured to memory. ::
+
+                 +--------------------------------------+
+                 !                                      !
+                 !                                      !
+                 !                                      !
+                 !              __/(_____/|             !
+                 !            >.___  ____ (             !
+                 !                 \(    \|             !
+                 !                                      !
+                 !                                      !
+                 !                                      !
+                 +--------------------------------------+
+
+    A software rotation correction of 180 degrees has to be applied to correctly
+    display the image on the user screen. ::
+
+                 +--------------------------------------+
+                 !                                      !
+                 !                                      !
+                 !                                      !
+                 !             |\____)\___              !
+                 !             ) _____  __`<            !
+                 !             |/     )/                !
+                 !                                      !
+                 !                                      !
+                 !                                      !
+                 +--------------------------------------+
+
+    Example two - Phone camera
+
+    It is more handy to go and swim with sharks with only your mobile phone
+    with you and take pictures with the camera that is installed on the back
+    side of the device, facing away from the user. The captured images are meant
+    to be displayed in portrait mode (height > width) to match the device screen
+    orientation and the device usage orientation used when taking the picture.
+
+    The camera sensor is typically mounted with its pixel array longer side
+    aligned to the device longer side, upside-down mounted to compensate for
+    the lens optical inversion effect.
+
+    The images once captured to memory will be rotated and the value of the
+    V4L2_CID_CAMERA_SENSOR_ROTATION will report a 90 degree rotation. ::
+
+
+                 +-------------------------------------+
+                 |                 _ _                 |
+                 |                \   /                |
+                 |                 | |                 |
+                 |                 | |                 |
+                 |                 |  >                |
+                 |                <  |                 |
+                 |                 | |                 |
+                 |                   .                 |
+                 |                  V                  |
+                 +-------------------------------------+
+
+    A correction of 90 degrees in counter-clockwise direction has to be
+    applied to correctly display the image in portrait mode on the device
+    screen. ::
+
+                          +--------------------+
+                          |                    |
+                          |                    |
+                          |                    |
+                          |                    |
+                          |                    |
+                          |                    |
+                          |   |\____)\___      |
+                          |   ) _____  __`<    |
+                          |   |/     )/        |
+                          |                    |
+                          |                    |
+                          |                    |
+                          |                    |
+                          |                    |
+                          +--------------------+
+
+
 .. [#f1]
    This control may be changed to a menu control in the future, if more
    options are required.

Documentation/media/uapi/v4l/ext-ctrls-codec.rst

@@ -1983,9 +1983,9 @@ enum v4l2_mpeg_video_h264_hierarchical_coding_type -
       - ``reference_ts``
       - Timestamp of the V4L2 capture buffer to use as reference, used
         with B-coded and P-coded frames. The timestamp refers to the
-	``timestamp`` field in struct :c:type:`v4l2_buffer`. Use the
-	:c:func:`v4l2_timeval_to_ns()` function to convert the struct
-	:c:type:`timeval` in struct :c:type:`v4l2_buffer` to a __u64.
+        ``timestamp`` field in struct :c:type:`v4l2_buffer`. Use the
+        :c:func:`v4l2_timeval_to_ns()` function to convert the struct
+        :c:type:`timeval` in struct :c:type:`v4l2_buffer` to a __u64.
     * - __u16
       - ``frame_num``
       -
@@ -3693,3 +3693,594 @@ enum v4l2_mpeg_video_hevc_size_of_length_field -
     Indicates whether to generate SPS and PPS at every IDR. Setting it to 0
     disables generating SPS and PPS at every IDR. Setting it to one enables
     generating SPS and PPS at every IDR.
+
+.. _v4l2-mpeg-hevc:
+
+``V4L2_CID_MPEG_VIDEO_HEVC_SPS (struct)``
+    Specifies the Sequence Parameter Set fields (as extracted from the
+    bitstream) for the associated HEVC slice data.
+    These bitstream parameters are defined according to :ref:`hevc`.
+    They are described in section 7.4.3.2 "Sequence parameter set RBSP
+    semantics" of the specification.
+
+.. c:type:: v4l2_ctrl_hevc_sps
+
+.. cssclass:: longtable
+
+.. flat-table:: struct v4l2_ctrl_hevc_sps
+    :header-rows:  0
+    :stub-columns: 0
+    :widths:       1 1 2
+
+    * - __u16
+      - ``pic_width_in_luma_samples``
+      -
+    * - __u16
+      - ``pic_height_in_luma_samples``
+      -
+    * - __u8
+      - ``bit_depth_luma_minus8``
+      -
+    * - __u8
+      - ``bit_depth_chroma_minus8``
+      -
+    * - __u8
+      - ``log2_max_pic_order_cnt_lsb_minus4``
+      -
+    * - __u8
+      - ``sps_max_dec_pic_buffering_minus1``
+      -
+    * - __u8
+      - ``sps_max_num_reorder_pics``
+      -
+    * - __u8
+      - ``sps_max_latency_increase_plus1``
+      -
+    * - __u8
+      - ``log2_min_luma_coding_block_size_minus3``
+      -
+    * - __u8
+      - ``log2_diff_max_min_luma_coding_block_size``
+      -
+    * - __u8
+      - ``log2_min_luma_transform_block_size_minus2``
+      -
+    * - __u8
+      - ``log2_diff_max_min_luma_transform_block_size``
+      -
+    * - __u8
+      - ``max_transform_hierarchy_depth_inter``
+      -
+    * - __u8
+      - ``max_transform_hierarchy_depth_intra``
+      -
+    * - __u8
+      - ``pcm_sample_bit_depth_luma_minus1``
+      -
+    * - __u8
+      - ``pcm_sample_bit_depth_chroma_minus1``
+      -
+    * - __u8
+      - ``log2_min_pcm_luma_coding_block_size_minus3``
+      -
+    * - __u8
+      - ``log2_diff_max_min_pcm_luma_coding_block_size``
+      -
+    * - __u8
+      - ``num_short_term_ref_pic_sets``
+      -
+    * - __u8
+      - ``num_long_term_ref_pics_sps``
+      -
+    * - __u8
+      - ``chroma_format_idc``
+      -
+    * - __u64
+      - ``flags``
+      - See :ref:`Sequence Parameter Set Flags <hevc_sps_flags>`
+
+.. _hevc_sps_flags:
+
+``Sequence Parameter Set Flags``
+
+.. cssclass:: longtable
+
+.. flat-table::
+    :header-rows:  0
+    :stub-columns: 0
+    :widths:       1 1 2
+
+    * - ``V4L2_HEVC_SPS_FLAG_SEPARATE_COLOUR_PLANE``
+      - 0x00000001
+      -
+    * - ``V4L2_HEVC_SPS_FLAG_SCALING_LIST_ENABLED``
+      - 0x00000002
+      -
+    * - ``V4L2_HEVC_SPS_FLAG_AMP_ENABLED``
+      - 0x00000004
+      -
+    * - ``V4L2_HEVC_SPS_FLAG_SAMPLE_ADAPTIVE_OFFSET``
+      - 0x00000008
+      -
+    * - ``V4L2_HEVC_SPS_FLAG_PCM_ENABLED``
+      - 0x00000010
+      -
+    * - ``V4L2_HEVC_SPS_FLAG_PCM_LOOP_FILTER_DISABLED``
+      - 0x00000020
+      -
+    * - ``V4L2_HEVC_SPS_FLAG_LONG_TERM_REF_PICS_PRESENT``
+      - 0x00000040
+      -
+    * - ``V4L2_HEVC_SPS_FLAG_SPS_TEMPORAL_MVP_ENABLED``
+      - 0x00000080
+      -
+    * - ``V4L2_HEVC_SPS_FLAG_STRONG_INTRA_SMOOTHING_ENABLED``
+      - 0x00000100
+      -
+
+``V4L2_CID_MPEG_VIDEO_HEVC_PPS (struct)``
+    Specifies the Picture Parameter Set fields (as extracted from the
+    bitstream) for the associated HEVC slice data.
+    These bitstream parameters are defined according to :ref:`hevc`.
+    They are described in section 7.4.3.3 "Picture parameter set RBSP
+    semantics" of the specification.
+
+.. c:type:: v4l2_ctrl_hevc_pps
+
+.. cssclass:: longtable
+
+.. flat-table:: struct v4l2_ctrl_hevc_pps
+    :header-rows:  0
+    :stub-columns: 0
+    :widths:       1 1 2
+
+    * - __u8
+      - ``num_extra_slice_header_bits``
+      -
+    * - __s8
+      - ``init_qp_minus26``
+      -
+    * - __u8
+      - ``diff_cu_qp_delta_depth``
+      -
+    * - __s8
+      - ``pps_cb_qp_offset``
+      -
+    * - __s8
+      - ``pps_cr_qp_offset``
+      -
+    * - __u8
+      - ``num_tile_columns_minus1``
+      -
+    * - __u8
+      - ``num_tile_rows_minus1``
+      -
+    * - __u8
+      - ``column_width_minus1[20]``
+      -
+    * - __u8
+      - ``row_height_minus1[22]``
+      -
+    * - __s8
+      - ``pps_beta_offset_div2``
+      -
+    * - __s8
+      - ``pps_tc_offset_div2``
+      -
+    * - __u8
+      - ``log2_parallel_merge_level_minus2``
+      -
+    * - __u8
+      - ``padding[4]``
+      - Applications and drivers must set this to zero.
+    * - __u64
+      - ``flags``
+      - See :ref:`Picture Parameter Set Flags <hevc_pps_flags>`
+
+.. _hevc_pps_flags:
+
+``Picture Parameter Set Flags``
+
+.. cssclass:: longtable
+
+.. flat-table::
+    :header-rows:  0
+    :stub-columns: 0
+    :widths:       1 1 2
+
+    * - ``V4L2_HEVC_PPS_FLAG_DEPENDENT_SLICE_SEGMENT``
+      - 0x00000001
+      -
+    * - ``V4L2_HEVC_PPS_FLAG_OUTPUT_FLAG_PRESENT``
+      - 0x00000002
+      -
+    * - ``V4L2_HEVC_PPS_FLAG_SIGN_DATA_HIDING_ENABLED``
+      - 0x00000004
+      -
+    * - ``V4L2_HEVC_PPS_FLAG_CABAC_INIT_PRESENT``
+      - 0x00000008
+      -
+    * - ``V4L2_HEVC_PPS_FLAG_CONSTRAINED_INTRA_PRED``
+      - 0x00000010
+      -
+    * - ``V4L2_HEVC_PPS_FLAG_TRANSFORM_SKIP_ENABLED``
+      - 0x00000020
+      -
+    * - ``V4L2_HEVC_PPS_FLAG_CU_QP_DELTA_ENABLED``
+      - 0x00000040
+      -
+    * - ``V4L2_HEVC_PPS_FLAG_PPS_SLICE_CHROMA_QP_OFFSETS_PRESENT``
+      - 0x00000080
+      -
+    * - ``V4L2_HEVC_PPS_FLAG_WEIGHTED_PRED``
+      - 0x00000100
+      -
+    * - ``V4L2_HEVC_PPS_FLAG_WEIGHTED_BIPRED``
+      - 0x00000200
+      -
+    * - ``V4L2_HEVC_PPS_FLAG_TRANSQUANT_BYPASS_ENABLED``
+      - 0x00000400
+      -
+    * - ``V4L2_HEVC_PPS_FLAG_TILES_ENABLED``
+      - 0x00000800
+      -
+    * - ``V4L2_HEVC_PPS_FLAG_ENTROPY_CODING_SYNC_ENABLED``
+      - 0x00001000
+      -
+    * - ``V4L2_HEVC_PPS_FLAG_LOOP_FILTER_ACROSS_TILES_ENABLED``
+      - 0x00002000
+      -
+    * - ``V4L2_HEVC_PPS_FLAG_PPS_LOOP_FILTER_ACROSS_SLICES_ENABLED``
+      - 0x00004000
+      -
+    * - ``V4L2_HEVC_PPS_FLAG_DEBLOCKING_FILTER_OVERRIDE_ENABLED``
+      - 0x00008000
+      -
+    * - ``V4L2_HEVC_PPS_FLAG_PPS_DISABLE_DEBLOCKING_FILTER``
+      - 0x00010000
+      -
+    * - ``V4L2_HEVC_PPS_FLAG_LISTS_MODIFICATION_PRESENT``
+      - 0x00020000
+      -
+    * - ``V4L2_HEVC_PPS_FLAG_SLICE_SEGMENT_HEADER_EXTENSION_PRESENT``
+      - 0x00040000
+      -
+
+``V4L2_CID_MPEG_VIDEO_HEVC_SLICE_PARAMS (struct)``
+    Specifies various slice-specific parameters, especially from the NAL unit
+    header, general slice segment header and weighted prediction parameter
+    parts of the bitstream.
+    These bitstream parameters are defined according to :ref:`hevc`.
+    They are described in section 7.4.7 "General slice segment header
+    semantics" of the specification.
+
+.. c:type:: v4l2_ctrl_hevc_slice_params
+
+.. cssclass:: longtable
+
+.. flat-table:: struct v4l2_ctrl_hevc_slice_params
+    :header-rows:  0
+    :stub-columns: 0
+    :widths:       1 1 2
+
+    * - __u32
+      - ``bit_size``
+      - Size (in bits) of the current slice data.
+    * - __u32
+      - ``data_bit_offset``
+      - Offset (in bits) to the video data in the current slice data.
+    * - __u32
+      - ``slice_segment_addr``
+      -
+    * - __u8
+      - ``nal_unit_type``
+      -
+    * - __u8
+      - ``nuh_temporal_id_plus1``
+      -
+    * - __u8
+      - ``slice_type``
+      -
+	(V4L2_HEVC_SLICE_TYPE_I, V4L2_HEVC_SLICE_TYPE_P or
+	V4L2_HEVC_SLICE_TYPE_B).
+    * - __u8
+      - ``colour_plane_id``
+      -
+    * - __u16
+      - ``slice_pic_order_cnt``
+      -
+    * - __u8
+      - ``num_ref_idx_l0_active_minus1``
+      -
+    * - __u8
+      - ``num_ref_idx_l1_active_minus1``
+      -
+    * - __u8
+      - ``collocated_ref_idx``
+      -
+    * - __u8
+      - ``five_minus_max_num_merge_cand``
+      -
+    * - __s8
+      - ``slice_qp_delta``
+      -
+    * - __s8
+      - ``slice_cb_qp_offset``
+      -
+    * - __s8
+      - ``slice_cr_qp_offset``
+      -
+    * - __s8
+      - ``slice_act_y_qp_offset``
+      -
+    * - __s8
+      - ``slice_act_cb_qp_offset``
+      -
+    * - __s8
+      - ``slice_act_cr_qp_offset``
+      -
+    * - __s8
+      - ``slice_beta_offset_div2``
+      -
+    * - __s8
+      - ``slice_tc_offset_div2``
+      -
+    * - __u8
+      - ``pic_struct``
+      -
+    * - __u8
+      - ``num_active_dpb_entries``
+      - The number of entries in ``dpb``.
+    * - __u8
+      - ``ref_idx_l0[V4L2_HEVC_DPB_ENTRIES_NUM_MAX]``
+      - The list of L0 reference elements as indices in the DPB.
+    * - __u8
+      - ``ref_idx_l1[V4L2_HEVC_DPB_ENTRIES_NUM_MAX]``
+      - The list of L1 reference elements as indices in the DPB.
+    * - __u8
+      - ``num_rps_poc_st_curr_before``
+      - The number of reference pictures in the short-term set that come before
+        the current frame.
+    * - __u8
+      - ``num_rps_poc_st_curr_after``
+      - The number of reference pictures in the short-term set that come after
+        the current frame.
+    * - __u8
+      - ``num_rps_poc_lt_curr``
+      - The number of reference pictures in the long-term set.
+    * - __u8
+      - ``padding[5]``
+      - Applications and drivers must set this to zero.
+    * - struct :c:type:`v4l2_hevc_dpb_entry`
+      - ``dpb[V4L2_HEVC_DPB_ENTRIES_NUM_MAX]``
+      - The decoded picture buffer, for meta-data about reference frames.
+    * - struct :c:type:`v4l2_hevc_pred_weight_table`
+      - ``pred_weight_table``
+      - The prediction weight coefficients for inter-picture prediction.
+    * - __u64
+      - ``flags``
+      - See :ref:`Slice Parameters Flags <hevc_slice_params_flags>`
+
+.. _hevc_slice_params_flags:
+
+``Slice Parameters Flags``
+
+.. cssclass:: longtable
+
+.. flat-table::
+    :header-rows:  0
+    :stub-columns: 0
+    :widths:       1 1 2
+
+    * - ``V4L2_HEVC_SLICE_PARAMS_FLAG_SLICE_SAO_LUMA``
+      - 0x00000001
+      -
+    * - ``V4L2_HEVC_SLICE_PARAMS_FLAG_SLICE_SAO_CHROMA``
+      - 0x00000002
+      -
+    * - ``V4L2_HEVC_SLICE_PARAMS_FLAG_SLICE_TEMPORAL_MVP_ENABLED``
+      - 0x00000004
+      -
+    * - ``V4L2_HEVC_SLICE_PARAMS_FLAG_MVD_L1_ZERO``
+      - 0x00000008
+      -
+    * - ``V4L2_HEVC_SLICE_PARAMS_FLAG_CABAC_INIT``
+      - 0x00000010
+      -
+    * - ``V4L2_HEVC_SLICE_PARAMS_FLAG_COLLOCATED_FROM_L0``
+      - 0x00000020
+      -
+    * - ``V4L2_HEVC_SLICE_PARAMS_FLAG_USE_INTEGER_MV``
+      - 0x00000040
+      -
+    * - ``V4L2_HEVC_SLICE_PARAMS_FLAG_SLICE_DEBLOCKING_FILTER_DISABLED``
+      - 0x00000080
+      -
+    * - ``V4L2_HEVC_SLICE_PARAMS_FLAG_SLICE_LOOP_FILTER_ACROSS_SLICES_ENABLED``
+      - 0x00000100
+      -
+
+.. c:type:: v4l2_hevc_dpb_entry
+
+.. cssclass:: longtable
+
+.. flat-table:: struct v4l2_hevc_dpb_entry
+    :header-rows:  0
+    :stub-columns: 0
+    :widths:       1 1 2
+
+    * - __u64
+      - ``timestamp``
+      - Timestamp of the V4L2 capture buffer to use as reference, used
+        with B-coded and P-coded frames. The timestamp refers to the
+	``timestamp`` field in struct :c:type:`v4l2_buffer`. Use the
+	:c:func:`v4l2_timeval_to_ns()` function to convert the struct
+	:c:type:`timeval` in struct :c:type:`v4l2_buffer` to a __u64.
+    * - __u8
+      - ``rps``
+      - The reference set for the reference frame
+        (V4L2_HEVC_DPB_ENTRY_RPS_ST_CURR_BEFORE,
+        V4L2_HEVC_DPB_ENTRY_RPS_ST_CURR_AFTER or
+        V4L2_HEVC_DPB_ENTRY_RPS_LT_CURR)
+    * - __u8
+      - ``field_pic``
+      - Whether the reference is a field picture or a frame.
+    * - __u16
+      - ``pic_order_cnt[2]``
+      - The picture order count of the reference. Only the first element of the
+        array is used for frame pictures, while the first element identifies the
+        top field and the second the bottom field in field-coded pictures.
+    * - __u8
+      - ``padding[2]``
+      - Applications and drivers must set this to zero.
+
+.. c:type:: v4l2_hevc_pred_weight_table
+
+.. cssclass:: longtable
+
+.. flat-table:: struct v4l2_hevc_pred_weight_table
+    :header-rows:  0
+    :stub-columns: 0
+    :widths:       1 1 2
+
+    * - __u8
+      - ``luma_log2_weight_denom``
+      -
+    * - __s8
+      - ``delta_chroma_log2_weight_denom``
+      -
+    * - __s8
+      - ``delta_luma_weight_l0[V4L2_HEVC_DPB_ENTRIES_NUM_MAX]``
+      -
+    * - __s8
+      - ``luma_offset_l0[V4L2_HEVC_DPB_ENTRIES_NUM_MAX]``
+      -
+    * - __s8
+      - ``delta_chroma_weight_l0[V4L2_HEVC_DPB_ENTRIES_NUM_MAX][2]``
+      -
+    * - __s8
+      - ``chroma_offset_l0[V4L2_HEVC_DPB_ENTRIES_NUM_MAX][2]``
+      -
+    * - __s8
+      - ``delta_luma_weight_l1[V4L2_HEVC_DPB_ENTRIES_NUM_MAX]``
+      -
+    * - __s8
+      - ``luma_offset_l1[V4L2_HEVC_DPB_ENTRIES_NUM_MAX]``
+      -
+    * - __s8
+      - ``delta_chroma_weight_l1[V4L2_HEVC_DPB_ENTRIES_NUM_MAX][2]``
+      -
+    * - __s8
+      - ``chroma_offset_l1[V4L2_HEVC_DPB_ENTRIES_NUM_MAX][2]``
+      -
+    * - __u8
+      - ``padding[6]``
+      - Applications and drivers must set this to zero.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_SCALING_MATRIX (struct)``
+    Specifies the scaling matrix (as extracted from the bitstream) for
+    the associated HEVC slice data. The bitstream parameters are
+    defined according to :ref:`hevc`, section 7.4.5 "Scaling list
+    data semantics". For further documentation, refer to the above
+    specification, unless there is an explicit comment stating
+    otherwise.
+
+    .. note::
+
+       This compound control is not yet part of the public kernel API and
+       it is expected to change.
+
+.. c:type:: v4l2_ctrl_hevc_scaling_matrix
+
+.. cssclass:: longtable
+
+.. flat-table:: struct v4l2_ctrl_hevc_scaling_matrix
+    :header-rows:  0
+    :stub-columns: 0
+    :widths:       1 1 2
+
+    * - __u8
+      - ``scaling_list_4x4[6][16]``
+      -
+    * - __u8
+      - ``scaling_list_8x8[6][64]``
+      -
+    * - __u8
+      - ``scaling_list_16x16[6][64]``
+      -
+    * - __u8
+      - ``scaling_list_32x32[2][64]``
+      -
+    * - __u8
+      - ``scaling_list_dc_coef_16x16[6]``
+      -
+    * - __u8
+      - ``scaling_list_dc_coef_32x32[2]``
+      -
+
+``V4L2_CID_MPEG_VIDEO_HEVC_DECODE_MODE (enum)``
+    Specifies the decoding mode to use. Currently exposes slice-based and
+    frame-based decoding but new modes might be added later on.
+    This control is used as a modifier for V4L2_PIX_FMT_HEVC_SLICE
+    pixel format. Applications that support V4L2_PIX_FMT_HEVC_SLICE
+    are required to set this control in order to specify the decoding mode
+    that is expected for the buffer.
+    Drivers may expose a single or multiple decoding modes, depending
+    on what they can support.
+
+    .. note::
+
+       This menu control is not yet part of the public kernel API and
+       it is expected to change.
+
+.. c:type:: v4l2_mpeg_video_hevc_decode_mode
+
+.. cssclass:: longtable
+
+.. flat-table::
+    :header-rows:  0
+    :stub-columns: 0
+    :widths:       1 1 2
+
+    * - ``V4L2_MPEG_VIDEO_HEVC_DECODE_MODE_SLICE_BASED``
+      - 0
+      - Decoding is done at the slice granularity.
+        The OUTPUT buffer must contain a single slice.
+    * - ``V4L2_MPEG_VIDEO_HEVC_DECODE_MODE_FRAME_BASED``
+      - 1
+      - Decoding is done at the frame granularity.
+        The OUTPUT buffer must contain all slices needed to decode the
+        frame. The OUTPUT buffer must also contain both fields.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_START_CODE (enum)``
+    Specifies the HEVC slice start code expected for each slice.
+    This control is used as a modifier for V4L2_PIX_FMT_HEVC_SLICE
+    pixel format. Applications that support V4L2_PIX_FMT_HEVC_SLICE
+    are required to set this control in order to specify the start code
+    that is expected for the buffer.
+    Drivers may expose a single or multiple start codes, depending
+    on what they can support.
+
+    .. note::
+
+       This menu control is not yet part of the public kernel API and
+       it is expected to change.
+
+.. c:type:: v4l2_mpeg_video_hevc_start_code
+
+.. cssclass:: longtable
+
+.. flat-table::
+    :header-rows:  0
+    :stub-columns: 0
+    :widths:       1 1 2
+
+    * - ``V4L2_MPEG_VIDEO_HEVC_START_CODE_NONE``
+      - 0
+      - Selecting this value specifies that HEVC slices are passed
+        to the driver without any start code.
+    * - ``V4L2_MPEG_VIDEO_HEVC_START_CODE_ANNEX_B``
+      - 1
+      - Selecting this value specifies that HEVC slices are expected
+        to be prefixed by Annex B start codes. According to :ref:`hevc`
+        valid start codes can be 3-bytes 0x000001 or 4-bytes 0x00000001.

Documentation/media/uapi/v4l/meta-formats.rst

@@ -19,8 +19,10 @@ These formats are used for the :ref:`metadata` interface only.
 .. toctree::
     :maxdepth: 1
 
+    pixfmt-meta-bcm2835-isp-stats
     pixfmt-meta-d4xx
     pixfmt-meta-intel-ipu3
+    pixfmt-meta-sensor-data
     pixfmt-meta-uvc
     pixfmt-meta-vsp1-hgo
     pixfmt-meta-vsp1-hgt

Documentation/media/uapi/v4l/pixfmt-bayer.rst

@@ -34,5 +34,6 @@ orders. See also `the Wikipedia article on Bayer filter
     pixfmt-srggb10-ipu3
     pixfmt-srggb12
     pixfmt-srggb12p
+    pixfmt-srggb14
     pixfmt-srggb14p
     pixfmt-srggb16

Documentation/media/uapi/v4l/pixfmt-compressed.rst

@@ -188,6 +188,30 @@ Compressed Formats
 	If :ref:`VIDIOC_ENUM_FMT` reports ``V4L2_FMT_FLAG_CONTINUOUS_BYTESTREAM``
 	then the decoder has no	requirements since it can parse all the
 	information from the raw bytestream.
+    * .. _V4L2-PIX-FMT-HEVC-SLICE:
+
+      - ``V4L2_PIX_FMT_HEVC_SLICE``
+      - 'S265'
+      - HEVC parsed slice data, as extracted from the HEVC bitstream.
+	This format is adapted for stateless video decoders that implement a
+	HEVC pipeline (using the :ref:`mem2mem` and :ref:`media-request-api`).
+	This pixelformat has two modifiers that must be set at least once
+	through the ``V4L2_CID_MPEG_VIDEO_HEVC_DECODE_MODE``
+        and ``V4L2_CID_MPEG_VIDEO_HEVC_START_CODE`` controls.
+	Metadata associated with the frame to decode is required to be passed
+	through the following controls :
+        * ``V4L2_CID_MPEG_VIDEO_HEVC_SPS``
+        * ``V4L2_CID_MPEG_VIDEO_HEVC_PPS``
+        * ``V4L2_CID_MPEG_VIDEO_HEVC_SLICE_PARAMS``
+        * ``V4L2_CID_MPEG_VIDEO_HEVC_SCALING_MATRIX``
+	See the :ref:`associated Codec Control IDs <v4l2-mpeg-hevc>`.
+	Buffers associated with this pixel format must contain the appropriate
+	number of macroblocks to decode a full corresponding frame.
+
+	.. note::
+
+	   This format is not yet part of the public kernel API and it
+	   is expected to change.
     * .. _V4L2-PIX-FMT-FWHT:
 
       - ``V4L2_PIX_FMT_FWHT``

Documentation/media/uapi/v4l/pixfmt-meta-bcm2835-isp-stats.rst

@@ -0,0 +1,41 @@
+.. Permission is granted to copy, distribute and/or modify this
+.. document under the terms of the GNU Free Documentation License,
+.. Version 1.1 or any later version published by the Free Software
+.. Foundation, with no Invariant Sections, no Front-Cover Texts
+.. and no Back-Cover Texts. A copy of the license is included at
+.. Documentation/media/uapi/fdl-appendix.rst.
+..
+.. TODO: replace it to GFDL-1.1-or-later WITH no-invariant-sections
+
+.. _v4l2-meta-fmt-bcm2835-isp-stats:
+
+*****************************************
+V4L2_META_FMT_BCM2835_ISP_STATS  ('BSTA')
+*****************************************
+
+BCM2835 ISP Statistics
+
+Description
+===========
+
+The BCM2835 ISP hardware calculate image statistics for an input Bayer frame.
+These statistics are obtained from the "bcm2835-isp0-capture3" device node
+using the :c:type:`v4l2_meta_format` interface. They are formatted as described
+by the :c:type:`bcm2835_isp_stats` structure below.
+
+.. code-block:: c
+
+	#define DEFAULT_AWB_REGIONS_X 16
+	#define DEFAULT_AWB_REGIONS_Y 12
+
+	#define NUM_HISTOGRAMS 2
+	#define NUM_HISTOGRAM_BINS 128
+	#define AWB_REGIONS (DEFAULT_AWB_REGIONS_X * DEFAULT_AWB_REGIONS_Y)
+	#define FLOATING_REGIONS 16
+	#define AGC_REGIONS 16
+	#define FOCUS_REGIONS 12
+
+.. kernel-doc:: include/uapi/linux/bcm2835-isp.h
+   :functions: bcm2835_isp_stats_hist bcm2835_isp_stats_region
+	             bcm2835_isp_stats_focus bcm2835_isp_stats
+

Documentation/media/uapi/v4l/pixfmt-meta-sensor-data.rst

@@ -0,0 +1,32 @@
+.. Permission is granted to copy, distribute and/or modify this
+.. document under the terms of the GNU Free Documentation License,
+.. Version 1.1 or any later version published by the Free Software
+.. Foundation, with no Invariant Sections, no Front-Cover Texts
+.. and no Back-Cover Texts. A copy of the license is included at
+.. Documentation/media/uapi/fdl-appendix.rst.
+..
+.. TODO: replace it to GFDL-1.1-or-later WITH no-invariant-sections
+
+.. _v4l2-meta-fmt-sensor-data:
+
+***********************************
+V4L2_META_FMT_SENSOR_DATA  ('SENS')
+***********************************
+
+Sensor Ancillary Metadata
+
+Description
+===========
+
+This format describes ancillary data generated by a camera sensor and
+transmitted over a stream on the camera bus. Sensor vendors generally have their
+own custom format for this ancillary data. Some vendors follow a generic
+CSI-2/SMIA embedded data format as described in the `CSI-2 specification.
+<https://mipi.org/specifications/csi-2>`_
+
+The size of the embedded buffer is defined as a single line with a pixel width
+width specified in bytes. This is obtained by a call to the
+:c:type:`VIDIOC_SUBDEV_G_FMT` ioctl on the sensor subdevice where the ``pad``
+field in :c:type:`v4l2_subdev_format` is set to 1.  Note that this size is fixed
+and cannot be modified with a call to :c:type:`VIDIOC_SUBDEV_S_FMT`.
+

Documentation/media/uapi/v4l/pixfmt-nv12-col128.rst

@@ -0,0 +1,215 @@
+.. Permission is granted to copy, distribute and/or modify this
+.. document under the terms of the GNU Free Documentation License,
+.. Version 1.1 or any later version published by the Free Software
+.. Foundation, with no Invariant Sections, no Front-Cover Texts
+.. and no Back-Cover Texts. A copy of the license is included at
+.. Documentation/media/uapi/fdl-appendix.rst.
+..
+.. TODO: replace it to GFDL-1.1-or-later WITH no-invariant-sections
+
+.. _V4L2_PIX_FMT_NV12_COL128:
+.. _V4L2_PIX_FMT_NV12_10_COL128:
+
+********************************************************************************
+V4L2_PIX_FMT_NV12_COL128, V4L2_PIX_FMT_NV12_10_COL128
+********************************************************************************
+
+
+V4L2_PIX_FMT_NV21_COL128
+Formats with ½ horizontal and vertical chroma resolution. This format
+has two planes - one for luminance and one for chrominance. Chroma
+samples are interleaved. The difference to ``V4L2_PIX_FMT_NV12`` is the
+memory layout. The image is split into columns of 128 bytes wide rather than
+being in raster order.
+
+V4L2_PIX_FMT_NV12_10_COL128
+Follows the same pattern as ``V4L2_PIX_FMT_NV21_COL128`` with 128 byte, but is
+a 10bit format with 3 10-bit samples being packed into 4 bytes. Each 128 byte
+wide column therefore contains 96 samples.
+
+
+Description
+===========
+
+This is the two-plane versions of the YUV 4:2:0 format where data is
+grouped into 128 byte wide columns. The three components are separated into
+two sub-images or planes. The Y plane has one byte per pixel and pixels
+are grouped into 128 byte wide columns. The CbCr plane has the same width,
+in bytes, as the Y plane (and the image), but is half as tall in pixels.
+The chroma plane is also in 128 byte columns, reflecting 64 Cb and 64 Cr
+samples.
+
+The chroma samples for a column follow the luma samples. If there is any
+paddding, then that will be reflected via the selection API.
+The luma height must be a multiple of 2 lines.
+
+The normal bytesperline is effectively fixed at 128. However the format
+requires knowledge of the stride between columns, therefore the bytesperline
+value has been repurposed to denote the number of 128 byte long lines between
+the start of each column.
+
+**Byte Order.**
+
+
+.. flat-table::
+    :header-rows:  0
+    :stub-columns: 0
+    :widths: 12 12 12 12 12 4 12 12 12 12
+
+    * - start + 0:
+      - Y'\ :sub:`0,0`
+      - Y'\ :sub:`0,1`
+      - Y'\ :sub:`0,2`
+      - Y'\ :sub:`0,3`
+      - ...
+      - Y'\ :sub:`0,124`
+      - Y'\ :sub:`0,125`
+      - Y'\ :sub:`0,126`
+      - Y'\ :sub:`0,127`
+    * - start + 128:
+      - Y'\ :sub:`1,0`
+      - Y'\ :sub:`1,1`
+      - Y'\ :sub:`1,2`
+      - Y'\ :sub:`1,3`
+      - ...
+      - Y'\ :sub:`1,124`
+      - Y'\ :sub:`1,125`
+      - Y'\ :sub:`1,126`
+      - Y'\ :sub:`1,127`
+    * - start + 256:
+      - Y'\ :sub:`2,0`
+      - Y'\ :sub:`2,1`
+      - Y'\ :sub:`2,2`
+      - Y'\ :sub:`2,3`
+      - ...
+      - Y'\ :sub:`2,124`
+      - Y'\ :sub:`2,125`
+      - Y'\ :sub:`2,126`
+      - Y'\ :sub:`2,127`
+    * - ...
+      - ...
+      - ...
+      - ...
+      - ...
+      - ...
+      - ...
+      - ...
+    * - start + ((height-1) * 128):
+      - Y'\ :sub:`height-1,0`
+      - Y'\ :sub:`height-1,1`
+      - Y'\ :sub:`height-1,2`
+      - Y'\ :sub:`height-1,3`
+      - ...
+      - Y'\ :sub:`height-1,124`
+      - Y'\ :sub:`height-1,125`
+      - Y'\ :sub:`height-1,126`
+      - Y'\ :sub:`height-1,127`
+    * - start + ((height) * 128):
+      - Cb\ :sub:`0,0`
+      - Cr\ :sub:`0,0`
+      - Cb\ :sub:`0,1`
+      - Cr\ :sub:`0,1`
+      - ...
+      - Cb\ :sub:`0,62`
+      - Cr\ :sub:`0,62`
+      - Cb\ :sub:`0,63`
+      - Cr\ :sub:`0,63`
+    * - start + ((height+1) * 128):
+      - Cb\ :sub:`1,0`
+      - Cr\ :sub:`1,0`
+      - Cb\ :sub:`1,1`
+      - Cr\ :sub:`1,1`
+      - ...
+      - Cb\ :sub:`1,62`
+      - Cr\ :sub:`1,62`
+      - Cb\ :sub:`1,63`
+      - Cr\ :sub:`1,63`
+    * - ...
+      - ...
+      - ...
+      - ...
+      - ...
+      - ...
+      - ...
+      - ...
+    * - start + ((height+(height/2)-1) * 128):
+      - Cb\ :sub:`(height/2)-1,0`
+      - Cr\ :sub:`(height/2)-1,0`
+      - Cb\ :sub:`(height/2)-1,1`
+      - Cr\ :sub:`(height/2)-1,1`
+      - ...
+      - Cb\ :sub:`(height/2)-1,62`
+      - Cr\ :sub:`(height/2)-1,62`
+      - Cb\ :sub:`(height/2)-1,63`
+      - Cr\ :sub:`(height/2)-1,63`
+    * - start + (bytesperline * 128):
+      - Y'\ :sub:`0,128`
+      - Y'\ :sub:`0,129`
+      - Y'\ :sub:`0,130`
+      - Y'\ :sub:`0,131`
+      - ...
+      - Y'\ :sub:`0,252`
+      - Y'\ :sub:`0,253`
+      - Y'\ :sub:`0,254`
+      - Y'\ :sub:`0,255`
+    * - ...
+      - ...
+      - ...
+      - ...
+      - ...
+      - ...
+      - ...
+      - ...
+
+V4L2_PIX_FMT_NV12_10_COL128 uses the same 128 byte column structure, but
+encodes 10-bit YUV.
+3 10-bit values are packed into 4 bytes as bits 9:0, 19:10, and 29:20, with
+bits 30 & 31 unused. For the luma plane, bits 9:0 are Y0, 19:10 are Y1, and
+29:20 are Y2. For the chroma plane the samples always come in pairs of Cr
+and Cb, so it needs to be considered 6 values packed in 8 bytes.
+
+Bit-packed representation.
+
+.. raw:: latex
+
+    \small
+
+.. tabularcolumns:: |p{1.2cm}||p{1.2cm}||p{1.2cm}||p{1.2cm}|p{3.2cm}|p{3.2cm}|
+
+.. flat-table::
+    :header-rows:  0
+    :stub-columns: 0
+    :widths: 8 8 8 8
+
+    * - Y'\ :sub:`00[7:0]`
+      - Y'\ :sub:`01[5:0] (bits 7--2)` Y'\ :sub:`00[9:8]`\ (bits 1--0)
+      - Y'\ :sub:`02[3:0] (bits 7--4)` Y'\ :sub:`01[9:6]`\ (bits 3--0)
+      - unused (bits 7--6)` Y'\ :sub:`02[9:4]`\ (bits 5--0)
+
+.. raw:: latex
+
+    \small
+
+.. tabularcolumns:: |p{1.2cm}||p{1.2cm}||p{1.2cm}||p{1.2cm}|p{3.2cm}|p{3.2cm}|
+
+.. flat-table::
+    :header-rows:  0
+    :stub-columns: 0
+    :widths: 12 12 12 12 12 12 12 12
+
+    * - Cb\ :sub:`00[7:0]`
+      - Cr\ :sub:`00[5:0]`\ (bits 7--2) Cb\ :sub:`00[9:8]`\ (bits 1--0)
+      - Cb\ :sub:`01[3:0]`\ (bits 7--4) Cr\ :sub:`00[9:6]`\ (bits 3--0)
+      - unused (bits 7--6) Cb\ :sub:`02[9:4]`\ (bits 5--0)
+      - Cr\ :sub:`01[7:0]`
+      - Cb\ :sub:`02[5:0]`\ (bits 7--2) Cr\ :sub:`01[9:8]`\ (bits 1--0)
+      - Cr\ :sub:`02[3:0]`\ (bits 7--4) Cb\ :sub:`02[9:6]`\ (bits 3--0)
+      - unused (bits 7--6) Cr\ :sub:`02[9:4]`\ (bits 5--0)
+
+.. raw:: latex
+
+    \normalsize
+
+
+
+

Documentation/media/uapi/v4l/pixfmt-nv12.rst

@@ -10,9 +10,9 @@
 .. _V4L2-PIX-FMT-NV12:
 .. _V4L2-PIX-FMT-NV21:
 
-******************************************************
-V4L2_PIX_FMT_NV12 ('NV12'), V4L2_PIX_FMT_NV21 ('NV21')
-******************************************************
+********************************************************************************
+V4L2_PIX_FMT_NV12 ('NV12'), V4L2_PIX_FMT_NV21 ('NV21'), V4L2_PIX_FMT_NV12_COL128
+********************************************************************************
 
 
 V4L2_PIX_FMT_NV21
@@ -38,6 +38,14 @@ with a Cr byte.
 If the Y plane has pad bytes after each row, then the CbCr plane has as
 many pad bytes after its rows.
 
+``V4L2_PIX_FMT_NV12_COL128`` is the tiled version of
+``V4L2_PIX_FMT_NV12`` with the image broken down into 128 pixel wide columns of
+Y followed by the associated combined CbCr plane.
+The normal bytesperline is effectively fixed at 128. However the format
+requires knowledge of the stride between columns, therefore the bytesperline
+value has been repurposed to denote the number of 128 byte long lines between
+the start of each column.
+
 **Byte Order.**
 Each cell is one byte.
 

Documentation/media/uapi/v4l/pixfmt-srggb14.rst

@@ -0,0 +1,82 @@
+.. Permission is granted to copy, distribute and/or modify this
+.. document under the terms of the GNU Free Documentation License,
+.. Version 1.1 or any later version published by the Free Software
+.. Foundation, with no Invariant Sections, no Front-Cover Texts
+.. and no Back-Cover Texts. A copy of the license is included at
+.. Documentation/media/uapi/fdl-appendix.rst.
+..
+.. TODO: replace it to GFDL-1.1-or-later WITH no-invariant-sections
+
+.. _V4L2-PIX-FMT-SRGGB14:
+.. _v4l2-pix-fmt-sbggr14:
+.. _v4l2-pix-fmt-sgbrg14:
+.. _v4l2-pix-fmt-sgrbg14:
+
+
+***************************************************************************************************************************
+V4L2_PIX_FMT_SRGGB14 ('RG14'), V4L2_PIX_FMT_SGRBG14 ('GR14'), V4L2_PIX_FMT_SGBRG14 ('GB14'), V4L2_PIX_FMT_SBGGR14 ('BG14'),
+***************************************************************************************************************************
+
+
+14-bit Bayer formats expanded to 16 bits
+
+
+Description
+===========
+
+These four pixel formats are raw sRGB / Bayer formats with 14 bits per
+colour. Each sample is stored in a 16-bit word, with two unused high
+bits filled with zeros. Each n-pixel row contains n/2 green samples
+and n/2 blue or red samples, with alternating red and blue rows. Bytes
+are stored in memory in little endian order. They are conventionally
+described as GRGR... BGBG..., RGRG... GBGB..., etc. Below is an
+example of a small V4L2_PIX_FMT_SBGGR14 image:
+
+**Byte Order.**
+Each cell is one byte, the two most significant bits in the high bytes are
+zero.
+
+
+
+.. flat-table::
+    :header-rows:  0
+    :stub-columns: 0
+    :widths:       2 1 1 1 1 1 1 1 1
+
+
+    * - start + 0:
+      - B\ :sub:`00low`
+      - B\ :sub:`00high`
+      - G\ :sub:`01low`
+      - G\ :sub:`01high`
+      - B\ :sub:`02low`
+      - B\ :sub:`02high`
+      - G\ :sub:`03low`
+      - G\ :sub:`03high`
+    * - start + 8:
+      - G\ :sub:`10low`
+      - G\ :sub:`10high`
+      - R\ :sub:`11low`
+      - R\ :sub:`11high`
+      - G\ :sub:`12low`
+      - G\ :sub:`12high`
+      - R\ :sub:`13low`
+      - R\ :sub:`13high`
+    * - start + 16:
+      - B\ :sub:`20low`
+      - B\ :sub:`20high`
+      - G\ :sub:`21low`
+      - G\ :sub:`21high`
+      - B\ :sub:`22low`
+      - B\ :sub:`22high`
+      - G\ :sub:`23low`
+      - G\ :sub:`23high`
+    * - start + 24:
+      - G\ :sub:`30low`
+      - G\ :sub:`30high`
+      - R\ :sub:`31low`
+      - R\ :sub:`31high`
+      - G\ :sub:`32low`
+      - G\ :sub:`32high`
+      - R\ :sub:`33low`
+      - R\ :sub:`33high`

Documentation/media/uapi/v4l/pixfmt-y12p.rst

@@ -0,0 +1,45 @@
+.. Permission is granted to copy, distribute and/or modify this
+.. document under the terms of the GNU Free Documentation License,
+.. Version 1.1 or any later version published by the Free Software
+.. Foundation, with no Invariant Sections, no Front-Cover Texts
+.. and no Back-Cover Texts. A copy of the license is included at
+.. Documentation/media/uapi/fdl-appendix.rst.
+..
+.. TODO: replace it to GFDL-1.1-or-later WITH no-invariant-sections
+
+.. _V4L2-PIX-FMT-Y12P:
+
+******************************
+V4L2_PIX_FMT_Y12P ('Y12P')
+******************************
+
+Grey-scale image as a MIPI RAW12 packed array
+
+
+Description
+===========
+
+This is a packed grey-scale image format with a depth of 12 bits per
+pixel. Two consecutive pixels are packed into 3 bytes. The first 2 bytes
+contain the 8 high order bits of the pixels, and the 3rd byte contains the 4
+least significants bits of each pixel, in the same order.
+
+**Byte Order.**
+Each cell is one byte.
+
+.. tabularcolumns:: |p{2.2cm}|p{1.2cm}|p{1.2cm}|p{3.1cm}|
+
+
+.. flat-table::
+    :header-rows:  0
+    :stub-columns: 0
+    :widths:       2 1 1 1
+
+
+    -  -  start + 0:
+       -  Y'\ :sub:`00high`
+       -  Y'\ :sub:`01high`
+       -  Y'\ :sub:`01low`\ (bits 7--4)
+
+          Y'\ :sub:`00low`\ (bits 3--0)
+

Documentation/media/uapi/v4l/pixfmt-y14.rst

@@ -0,0 +1,72 @@
+.. Permission is granted to copy, distribute and/or modify this
+.. document under the terms of the GNU Free Documentation License,
+.. Version 1.1 or any later version published by the Free Software
+.. Foundation, with no Invariant Sections, no Front-Cover Texts
+.. and no Back-Cover Texts. A copy of the license is included at
+.. Documentation/media/uapi/fdl-appendix.rst.
+..
+.. TODO: replace it to GFDL-1.1-or-later WITH no-invariant-sections
+
+.. _V4L2-PIX-FMT-Y14:
+
+*************************
+V4L2_PIX_FMT_Y14 ('Y14 ')
+*************************
+
+
+Grey-scale image
+
+
+Description
+===========
+
+This is a grey-scale image with a depth of 14 bits per pixel. Pixels are
+stored in 16-bit words with unused high bits padded with 0. The least
+significant byte is stored at lower memory addresses (little-endian).
+
+**Byte Order.**
+Each cell is one byte.
+
+
+
+
+.. flat-table::
+    :header-rows:  0
+    :stub-columns: 0
+
+    * - start + 0:
+      - Y'\ :sub:`00low`
+      - Y'\ :sub:`00high`
+      - Y'\ :sub:`01low`
+      - Y'\ :sub:`01high`
+      - Y'\ :sub:`02low`
+      - Y'\ :sub:`02high`
+      - Y'\ :sub:`03low`
+      - Y'\ :sub:`03high`
+    * - start + 8:
+      - Y'\ :sub:`10low`
+      - Y'\ :sub:`10high`
+      - Y'\ :sub:`11low`
+      - Y'\ :sub:`11high`
+      - Y'\ :sub:`12low`
+      - Y'\ :sub:`12high`
+      - Y'\ :sub:`13low`
+      - Y'\ :sub:`13high`
+    * - start + 16:
+      - Y'\ :sub:`20low`
+      - Y'\ :sub:`20high`
+      - Y'\ :sub:`21low`
+      - Y'\ :sub:`21high`
+      - Y'\ :sub:`22low`
+      - Y'\ :sub:`22high`
+      - Y'\ :sub:`23low`
+      - Y'\ :sub:`23high`
+    * - start + 24:
+      - Y'\ :sub:`30low`
+      - Y'\ :sub:`30high`
+      - Y'\ :sub:`31low`
+      - Y'\ :sub:`31high`
+      - Y'\ :sub:`32low`
+      - Y'\ :sub:`32high`
+      - Y'\ :sub:`33low`
+      - Y'\ :sub:`33high`

Documentation/media/uapi/v4l/pixfmt-y14p.rst

@@ -0,0 +1,54 @@
+.. Permission is granted to copy, distribute and/or modify this
+.. document under the terms of the GNU Free Documentation License,
+.. Version 1.1 or any later version published by the Free Software
+.. Foundation, with no Invariant Sections, no Front-Cover Texts
+.. and no Back-Cover Texts. A copy of the license is included at
+.. Documentation/media/uapi/fdl-appendix.rst.
+..
+.. TODO: replace it to GFDL-1.1-or-later WITH no-invariant-sections
+
+.. _V4L2-PIX-FMT-Y14P:
+
+**************************
+V4L2_PIX_FMT_Y14P ('Y14P')
+**************************
+
+Grey-scale image as a MIPI RAW14 packed array
+
+
+Description
+===========
+
+This is a packed grey-scale image format with a depth of 14 bits per
+pixel. Every four consecutive samples are packed into seven bytes. Each
+of the first four bytes contain the eight high order bits of the pixels,
+and the three following bytes contains the six least significants bits of
+each pixel, in the same order.
+
+**Byte Order.**
+Each cell is one byte.
+
+.. tabularcolumns:: |p{1.8cm}|p{1.0cm}|p{1.0cm}|p{1.0cm}|p{1.1cm}|p{3.3cm}|p{3.3cm}|p{3.3cm}|
+
+.. flat-table::
+    :header-rows:  0
+    :stub-columns: 0
+    :widths:       2 1 1 1 1 3 3 3
+
+
+    -  -  start + 0:
+       -  Y'\ :sub:`00high`
+       -  Y'\ :sub:`01high`
+       -  Y'\ :sub:`02high`
+       -  Y'\ :sub:`03high`
+       -  Y'\ :sub:`01low bits 1--0`\ (bits 7--6)
+
+	  Y'\ :sub:`00low bits 5--0`\ (bits 5--0)
+
+       -  Y'\ :sub:`02low bits 3--0`\ (bits 7--4)
+
+	  Y'\ :sub:`01low bits 5--2`\ (bits 3--0)
+
+       -  Y'\ :sub:`03low bits 5--0`\ (bits 7--2)
+
+	  Y'\ :sub:`02low bits 5--4`\ (bits 1--0)

Documentation/media/uapi/v4l/subdev-formats.rst

@@ -5792,6 +5792,43 @@ the following codes.
       - u\ :sub:`2`
       - u\ :sub:`1`
       - u\ :sub:`0`
+    * .. _MEDIA-BUS-FMT-Y14-1X14:
+
+      - MEDIA_BUS_FMT_Y14_1X14
+      - 0x202d
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      - y\ :sub:`13`
+      - y\ :sub:`12`
+      - y\ :sub:`11`
+      - y\ :sub:`10`
+      - y\ :sub:`9`
+      - y\ :sub:`8`
+      - y\ :sub:`7`
+      - y\ :sub:`6`
+      - y\ :sub:`5`
+      - y\ :sub:`4`
+      - y\ :sub:`3`
+      - y\ :sub:`2`
+      - y\ :sub:`1`
+      - y\ :sub:`0`
     * .. _MEDIA-BUS-FMT-UYVY8-1X16:
 
       - MEDIA_BUS_FMT_UYVY8_1X16
@@ -7794,3 +7831,36 @@ formats.
       - 0x5001
       - Interleaved raw UYVY and JPEG image format with embedded meta-data
 	used by Samsung S3C73MX camera sensors.
+
+
+
+.. _v4l2-mbus-sensor-data:
+
+Sensor Ancillary Metadata Formats
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+This section lists ancillary data generated by a camera sensor and
+transmitted over a stream on the camera bus.
+
+The following table lists the existing sensor ancillary metadata formats:
+
+
+.. _v4l2-mbus-pixelcode-sensor-metadata:
+
+.. tabularcolumns:: |p{8.0cm}|p{1.4cm}|p{7.7cm}|
+
+.. flat-table:: Sensor ancillary metadata formats
+    :header-rows:  1
+    :stub-columns: 0
+
+    * - Identifier
+      - Code
+      - Comments
+    * .. _MEDIA_BUS_FMT_SENSOR_DATA:
+
+      - MEDIA_BUS_FMT_SENSOR_DATA
+      - 0x7001
+      - Sensor vendor specific ancillary metadata. Some vendors follow a generic
+        CSI-2/SMIA embedded data format as described in the `CSI-2 specification.
+	<https://mipi.org/specifications/csi-2>`_
+

Documentation/media/uapi/v4l/vidioc-decoder-cmd.rst

@@ -208,7 +208,15 @@ introduced in Linux 3.3. They are, however, mandatory for stateful mem2mem decod
 	been started yet, the driver will return an ``EPERM`` error code. When
 	the decoder is already running, this command does nothing. No
 	flags are defined for this command.
-
+    * - ``V4L2_DEC_CMD_FLUSH``
+      - 4
+      - Flush any held capture buffers. Only valid for stateless decoders.
+	This command is typically used when the application reached the
+	end of the stream and the last output buffer had the
+	``V4L2_BUF_FLAG_M2M_HOLD_CAPTURE_BUF`` flag set. This would prevent
+	dequeueing the capture buffer containing the last decoded frame.
+	So this command can be used to explicitly flush that final decoded
+	frame. This command does nothing if there are no held capture buffers.
 
 Return Value
 ============

Documentation/media/uapi/v4l/vidioc-g-dv-timings.rst

@@ -57,6 +57,10 @@ pointer to the struct :c:type:`v4l2_dv_timings`
 structure as argument. If the ioctl is not supported or the timing
 values are not correct, the driver returns ``EINVAL`` error code.
 
+Calling ``VIDIOC_SUBDEV_S_DV_TIMINGS`` on a subdev device node that has been
+registered in read-only mode is not allowed. An error is returned and the errno
+variable is set to ``-EPERM``.
+
 The ``linux/v4l2-dv-timings.h`` header can be used to get the timings of
 the formats in the :ref:`cea861` and :ref:`vesadmt` standards. If
 the current input or output does not support DV timings (e.g. if
@@ -81,6 +85,8 @@ ENODATA
 EBUSY
     The device is busy and therefore can not change the timings.
 
+EPERM
+    ``VIDIOC_SUBDEV_S_DV_TIMINGS`` has been called on a read-only subdevice.
 
 .. tabularcolumns:: |p{4.4cm}|p{4.4cm}|p{8.7cm}|
 

Documentation/media/uapi/v4l/vidioc-g-std.rst

@@ -66,6 +66,9 @@ video timings (e.g. if :ref:`VIDIOC_ENUMINPUT`
 does not set the ``V4L2_IN_CAP_STD`` flag), then ``ENODATA`` error code is
 returned.
 
+Calling ``VIDIOC_SUBDEV_S_STD`` on a subdev device node that has been registered
+in read-only mode is not allowed. An error is returned and the errno variable is
+set to ``-EPERM``.
 
 Return Value
 ============
@@ -79,3 +82,6 @@ EINVAL
 
 ENODATA
     Standard video timings are not supported for this input or output.
+
+EPERM
+    ``VIDIOC_SUBDEV_S_STD`` has been called on a read-only subdevice.

Documentation/media/uapi/v4l/vidioc-queryctrl.rst

@@ -443,6 +443,12 @@ See also the examples in :ref:`control`.
       - n/a
       - A struct :c:type:`v4l2_ctrl_mpeg2_quantization`, containing MPEG-2
 	quantization matrices for stateless video decoders.
+    * - ``V4L2_CTRL_TYPE_AREA``
+      - n/a
+      - n/a
+      - n/a
+      - A struct :c:type:`v4l2_area`, containing the width and the height
+        of a rectangular area. Units depend on the use case.
     * - ``V4L2_CTRL_TYPE_H264_SPS``
       - n/a
       - n/a
@@ -473,6 +479,24 @@ See also the examples in :ref:`control`.
       - n/a
       - A struct :c:type:`v4l2_ctrl_h264_decode_params`, containing H264
 	decode parameters for stateless video decoders.
+    * - ``V4L2_CTRL_TYPE_HEVC_SPS``
+      - n/a
+      - n/a
+      - n/a
+      - A struct :c:type:`v4l2_ctrl_hevc_sps`, containing HEVC Sequence
+	Parameter Set for stateless video decoders.
+    * - ``V4L2_CTRL_TYPE_HEVC_PPS``
+      - n/a
+      - n/a
+      - n/a
+      - A struct :c:type:`v4l2_ctrl_hevc_pps`, containing HEVC Picture
+	Parameter Set for stateless video decoders.
+    * - ``V4L2_CTRL_TYPE_HEVC_SLICE_PARAMS``
+      - n/a
+      - n/a
+      - n/a
+      - A struct :c:type:`v4l2_ctrl_hevc_slice_params`, containing HEVC
+	slice parameters for stateless video decoders.
 
 .. tabularcolumns:: |p{6.6cm}|p{2.2cm}|p{8.7cm}|
 

Documentation/media/uapi/v4l/vidioc-reqbufs.rst

@@ -125,6 +125,7 @@ aborting or finishing any DMA in progress, an implicit
 .. _V4L2-BUF-CAP-SUPPORTS-DMABUF:
 .. _V4L2-BUF-CAP-SUPPORTS-REQUESTS:
 .. _V4L2-BUF-CAP-SUPPORTS-ORPHANED-BUFS:
+.. _V4L2-BUF-CAP-SUPPORTS-M2M-HOLD-CAPTURE-BUF:
 
 .. cssclass:: longtable
 
@@ -150,6 +151,11 @@ aborting or finishing any DMA in progress, an implicit
       - The kernel allows calling :ref:`VIDIOC_REQBUFS` while buffers are still
         mapped or exported via DMABUF. These orphaned buffers will be freed
         when they are unmapped or when the exported DMABUF fds are closed.
+    * - ``V4L2_BUF_CAP_SUPPORTS_M2M_HOLD_CAPTURE_BUF``
+      - 0x00000020
+      - Only valid for stateless decoders. If set, then userspace can set the
+        ``V4L2_BUF_FLAG_M2M_HOLD_CAPTURE_BUF`` flag to hold off on returning the
+	capture buffer until the OUTPUT timestamp changes.
 
 Return Value
 ============

Documentation/media/uapi/v4l/vidioc-subdev-g-crop.rst

@@ -73,6 +73,11 @@ crop rectangles and stored in the sub-device file handle. Two
 applications querying the same sub-device would thus not interact with
 each other.
 
+If the subdev device node has been registered in read-only mode, calls to
+``VIDIOC_SUBDEV_S_CROP`` are only valid if the ``which`` field is set to
+``V4L2_SUBDEV_FORMAT_TRY``, otherwise an error is returned and the errno
+variable is set to ``-EPERM``.
+
 Drivers must not return an error solely because the requested crop
 rectangle doesn't match the device capabilities. They must instead
 modify the rectangle to match what the hardware can provide. The
@@ -123,3 +128,7 @@ EINVAL
     references a non-existing pad, the ``which`` field references a
     non-existing format, or cropping is not supported on the given
     subdev pad.
+
+EPERM
+    The ``VIDIOC_SUBDEV_S_CROP`` ioctl has been called on a read-only subdevice
+    and the ``which`` field is set to ``V4L2_SUBDEV_FORMAT_ACTIVE``.

Documentation/media/uapi/v4l/vidioc-subdev-g-fmt.rst

@@ -78,6 +78,11 @@ current links configuration or sub-device controls value. For instance,
 a low-pass noise filter might crop pixels at the frame boundaries,
 modifying its output frame size.
 
+If the subdev device node has been registered in read-only mode, calls to
+``VIDIOC_SUBDEV_S_FMT`` are only valid if the ``which`` field is set to
+``V4L2_SUBDEV_FORMAT_TRY``, otherwise an error is returned and the errno
+variable is set to ``-EPERM``.
+
 Drivers must not return an error solely because the requested format
 doesn't match the device capabilities. They must instead modify the
 format to match what the hardware can provide. The modified format
@@ -146,6 +151,9 @@ EINVAL
     ``pad`` references a non-existing pad, or the ``which`` field
     references a non-existing format.
 
+EPERM
+    The ``VIDIOC_SUBDEV_S_FMT`` ioctl has been called on a read-only subdevice
+    and the ``which`` field is set to ``V4L2_SUBDEV_FORMAT_ACTIVE``.
 
 ============
 

Documentation/media/uapi/v4l/vidioc-subdev-g-frame-interval.rst

@@ -65,6 +65,10 @@ struct
 contains the current frame interval as would be returned by a
 ``VIDIOC_SUBDEV_G_FRAME_INTERVAL`` call.
 
+Calling ``VIDIOC_SUBDEV_S_FRAME_INTERVAL`` on a subdev device node that has been
+registered in read-only mode is not allowed. An error is returned and the errno
+variable is set to ``-EPERM``.
+
 Drivers must not return an error solely because the requested interval
 doesn't match the device capabilities. They must instead modify the
 interval to match what the hardware can provide. The modified interval
@@ -118,3 +122,7 @@ EINVAL
     :c:type:`v4l2_subdev_frame_interval`
     ``pad`` references a non-existing pad, or the pad doesn't support
     frame intervals.
+
+EPERM
+    The ``VIDIOC_SUBDEV_S_FRAME_INTERVAL`` ioctl has been called on a read-only
+    subdevice.

Documentation/media/uapi/v4l/vidioc-subdev-g-selection.rst

@@ -53,6 +53,10 @@ function of the crop API, and more, are supported by the selections API.
 See :ref:`subdev` for more information on how each selection target
 affects the image processing pipeline inside the subdevice.
 
+If the subdev device node has been registered in read-only mode, calls to
+``VIDIOC_SUBDEV_S_SELECTION`` are only valid if the ``which`` field is set to
+``V4L2_SUBDEV_FORMAT_TRY``, otherwise an error is returned and the errno
+variable is set to ``-EPERM``.
 
 Types of selection targets
 --------------------------
@@ -123,3 +127,7 @@ EINVAL
     ``pad`` references a non-existing pad, the ``which`` field
     references a non-existing format, or the selection target is not
     supported on the given subdev pad.
+
+EPERM
+    The ``VIDIOC_SUBDEV_S_SELECTION`` ioctl has been called on a read-only
+    subdevice and the ``which`` field is set to ``V4L2_SUBDEV_FORMAT_ACTIVE``.

Documentation/media/uapi/v4l/yuv-formats.rst

@@ -35,6 +35,9 @@ to brightness information.
     pixfmt-grey
     pixfmt-y10
     pixfmt-y12
+    pixfmt-y12p
+    pixfmt-y14
+    pixfmt-y14p
     pixfmt-y10b
     pixfmt-y10p
     pixfmt-y16
@@ -57,6 +60,7 @@ to brightness information.
     pixfmt-nv12
     pixfmt-nv12m
     pixfmt-nv12mt
+    pixfmt-nv12-col128
     pixfmt-nv16
     pixfmt-nv16m
     pixfmt-nv24

Documentation/media/v4l-drivers/bcm2835-isp.rst

@@ -0,0 +1,127 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+BCM2835 ISP Driver
+==================
+
+Introduction
+------------
+
+The BCM2835 Image Sensor Pipeline (ISP) is a fixed function hardware pipeline
+for performing image processing operations.  Images are fed to the input
+of the ISP through memory frame buffers.  These images may be in various YUV,
+RGB, or Bayer formats.  A typical use case would have Bayer images obtained from
+an image sensor by the BCM2835 Unicam peripheral, written to a memory
+frame buffer, and finally fed into the input of the ISP.  Two concurrent output
+images may be generated in YUV or RGB format at different resolutions.
+Statistics output is also generated for Bayer input images.
+
+The bcm2835-isp driver exposes the following media pads as V4L2 device nodes:
+
+.. tabularcolumns:: |l|l|l|l|
+
+.. cssclass: longtable
+
+.. flat-table::
+
+    * - *Pad*
+      - *Direction*
+      - *Purpose*
+      - *Formats*
+
+    * - "bcm2835-isp0-output0"
+      - sink
+      - Accepts Bayer, RGB or YUV format frame buffers as input to the ISP HW
+        pipeline.
+      - :ref:`RAW8 <V4L2-PIX-FMT-SRGGB8>`,
+        :ref:`RAW10P <V4L2-PIX-FMT-SRGGB10P>`,
+        :ref:`RAW12P <V4L2-PIX-FMT-SRGGB12P>`,
+        :ref:`RAW14P <V4L2-PIX-FMT-SRGGB14P>`,
+        :ref:`RAW16 <V4L2-PIX-FMT-SRGGB16>`,
+        :ref:`RGB24/BGR24 <V4L2-PIX-FMT-RGB24>`,
+        :ref:`YUYV <V4L2-PIX-FMT-YUYV>`,
+        :ref:`YVYU <V4L2-PIX-FMT-YVYU>`,
+        :ref:`UYVY <V4L2-PIX-FMT-UYVY>`,
+        :ref:`VYUY <V4L2-PIX-FMT-VYUY>`,
+        :ref:`YUV420/YVU420 <V4L2-PIX-FMT-YUV420>`
+
+    * - "bcm2835-isp0-capture1"
+      - source
+      - High resolution YUV or RGB processed output from the ISP.
+      - :ref:`RGB565 <V4L2-PIX-FMT-RGB565>`,
+        :ref:`RGB24/BGR24 <V4L2-PIX-FMT-RGB24>`,
+        :ref:`ABGR32 <V4L2-PIX-FMT-ABGR32>`,
+        :ref:`YUYV <V4L2-PIX-FMT-YUYV>`,
+        :ref:`YVYU <V4L2-PIX-FMT-YVYU>`,
+        :ref:`UYVY <V4L2-PIX-FMT-UYVY>`,
+        :ref:`VYUY <V4L2-PIX-FMT-VYUY>`.
+        :ref:`YUV420/YVU420 <V4L2-PIX-FMT-YUV420>`,
+        :ref:`NV12/NV21 <V4L2-PIX-FMT-NV12>`,
+
+    * - "bcm2835-isp0-capture2"
+      - source
+      - Low resolution YUV processed output from the ISP. The output of
+        this pad cannot have a resolution larger than the "bcm2835-isp0-capture1" pad in any dimension.
+      - :ref:`YUYV <V4L2-PIX-FMT-YUYV>`,
+        :ref:`YVYU <V4L2-PIX-FMT-YVYU>`,
+        :ref:`UYVY <V4L2-PIX-FMT-UYVY>`,
+        :ref:`VYUY <V4L2-PIX-FMT-VYUY>`.
+        :ref:`YUV420/YVU420 <V4L2-PIX-FMT-YUV420>`,
+        :ref:`NV12/NV21 <V4L2-PIX-FMT-NV12>`,
+
+    * - "bcm2835-isp0-capture1"
+      - source
+      - Image statistics calculated from the input image provided on the
+        "bcm2835-isp0-output0" pad.  Statistics are only available for Bayer
+        format input images.
+      - :ref:`v4l2-meta-fmt-bcm2835-isp-stats`.
+
+Pipeline Configuration
+----------------------
+
+The ISP pipeline can be configure through user-space by calling
+:ref:`VIDIOC_S_EXT_CTRLS <VIDIOC_G_EXT_CTRLS>` on the “bcm2835-isp0-output0”
+node with the appropriate parameters as shown in the table below.
+
+.. tabularcolumns:: |p{2cm}|p{5.0cm}|
+
+.. cssclass: longtable
+
+.. flat-table::
+
+    * - *id*
+      - *Parameter*
+
+    * - ``V4L2_CID_USER_BCM2835_ISP_CC_MATRIX``
+      - struct :c:type:`bcm2835_isp_custom_ccm`
+
+    * - ``V4L2_CID_USER_BCM2835_ISP_LENS_SHADING``
+      - struct :c:type:`bcm2835_isp_lens_shading`
+
+    * - ``V4L2_CID_USER_BCM2835_ISP_BLACK_LEVEL``
+      - struct :c:type:`bcm2835_isp_black_level`
+
+    * - ``V4L2_CID_USER_BCM2835_ISP_GEQ``
+      - struct :c:type:`bcm2835_isp_geq`
+
+    * - ``V4L2_CID_USER_BCM2835_ISP_GAMMA``
+      - struct :c:type:`bcm2835_isp_gamma`
+
+    * - ``V4L2_CID_USER_BCM2835_ISP_DENOISE``
+      - struct :c:type:`bcm2835_isp_denoise`
+
+    * - ``V4L2_CID_USER_BCM2835_ISP_SHARPEN``
+      - struct :c:type:`bcm2835_isp_sharpen`
+
+    * - ``V4L2_CID_USER_BCM2835_ISP_DPC``
+      - struct :c:type:`bcm2835_isp_dpc`
+
+++++++++++++++++++++++++
+Configuration Parameters
+++++++++++++++++++++++++
+
+.. kernel-doc:: include/uapi/linux/bcm2835-isp.h
+   :functions: bcm2835_isp_rational bcm2835_isp_ccm bcm2835_isp_custom_ccm
+                bcm2835_isp_gain_format bcm2835_isp_lens_shading
+                bcm2835_isp_black_level bcm2835_isp_geq bcm2835_isp_gamma
+                bcm2835_isp_denoise bcm2835_isp_sharpen
+                bcm2835_isp_dpc_mode bcm2835_isp_dpc

Documentation/media/v4l-drivers/index.rst

@@ -35,6 +35,7 @@ For more details see the file COPYING in the source distribution of Linux.
 	v4l-with-ir
 	tuners
 	cardlist
+	bcm2835-isp
 	bttv
 	cafe_ccic
 	cpia2

Documentation/media/videodev2.h.rst.exceptions

@@ -141,6 +141,10 @@ replace symbol V4L2_CTRL_TYPE_H264_PPS :c:type:`v4l2_ctrl_type`
 replace symbol V4L2_CTRL_TYPE_H264_SCALING_MATRIX :c:type:`v4l2_ctrl_type`
 replace symbol V4L2_CTRL_TYPE_H264_SLICE_PARAMS :c:type:`v4l2_ctrl_type`
 replace symbol V4L2_CTRL_TYPE_H264_DECODE_PARAMS :c:type:`v4l2_ctrl_type`
+replace symbol V4L2_CTRL_TYPE_HEVC_SPS :c:type:`v4l2_ctrl_type`
+replace symbol V4L2_CTRL_TYPE_HEVC_PPS :c:type:`v4l2_ctrl_type`
+replace symbol V4L2_CTRL_TYPE_HEVC_SLICE_PARAMS :c:type:`v4l2_ctrl_type`
+replace symbol V4L2_CTRL_TYPE_AREA :c:type:`v4l2_ctrl_type`
 
 # V4L2 capability defines
 replace define V4L2_CAP_VIDEO_CAPTURE device-capabilities
@@ -434,6 +438,7 @@ replace define V4L2_DEC_CMD_START decoder-cmds
 replace define V4L2_DEC_CMD_STOP decoder-cmds
 replace define V4L2_DEC_CMD_PAUSE decoder-cmds
 replace define V4L2_DEC_CMD_RESUME decoder-cmds
+replace define V4L2_DEC_CMD_FLUSH decoder-cmds
 
 replace define V4L2_DEC_CMD_START_MUTE_AUDIO decoder-cmds
 replace define V4L2_DEC_CMD_PAUSE_TO_BLACK decoder-cmds

Documentation/virt/kvm/api.txt

@@ -4444,9 +4444,11 @@ EOI was received.
 #define KVM_EXIT_HYPERV_SYNIC          1
 #define KVM_EXIT_HYPERV_HCALL          2
 			__u32 type;
+			__u32 pad1;
 			union {
 				struct {
 					__u32 msr;
+					__u32 pad2;
 					__u64 control;
 					__u64 evt_page;
 					__u64 msg_page;

Documentation/w1/slaves/w1_therm.rst

@@ -26,20 +26,31 @@ W1_THERM_DS1825		0x3B
 W1_THERM_DS28EA00	0x42
 ====================	====
 
-Support is provided through the sysfs w1_slave file.  Each open and
+Support is provided through the sysfs w1_slave file. Each open and
 read sequence will initiate a temperature conversion then provide two
-lines of ASCII output.  The first line contains the nine hex bytes
+lines of ASCII output. The first line contains the nine hex bytes
 read along with a calculated crc value and YES or NO if it matched.
-If the crc matched the returned values are retained.  The second line
+If the crc matched the returned values are retained. The second line
 displays the retained values along with a temperature in millidegrees
 Centigrade after t=.
 
-Parasite powered devices are limited to one slave performing a
-temperature conversion at a time.  If none of the devices are parasite
-powered it would be possible to convert all the devices at the same
-time and then go back to read individual sensors.  That isn't
-currently supported.  The driver also doesn't support reduced
-precision (which would also reduce the conversion time) when reading values.
+Alternatively, temperature can be read using temperature sysfs, it
+return only temperature in millidegrees Centigrade.
+
+A bulk read of all devices on the bus could be done writing 'trigger'
+in the therm_bulk_read sysfs entry at w1_bus_master level. This will
+sent the convert command on all devices on the bus, and if parasite
+powered devices are detected on the bus (and strong pullup is enable
+in the module), it will drive the line high during the longer conversion
+time required by parasited powered device on the line. Reading
+therm_bulk_read will return 0 if no bulk conversion pending,
+-1 if at least one sensor still in conversion, 1 if conversion is complete
+but at least one sensor value has not been read yet. Result temperature is
+then accessed by reading the temperature sysfs entry of each device, which
+may return empty if conversion is still in progress. Note that if a bulk
+read is sent but one sensor is not read immediately, the next access to
+temperature on this device will return the temperature measured at the
+time of issue of the bulk read command (not the current temperature).
 
 Writing a value between 9 and 12 to the sysfs w1_slave file will change the
 precision of the sensor for the next readings. This value is in (volatile)
@@ -49,6 +60,27 @@ To store the current precision configuration into EEPROM, the value 0
 has to be written to the sysfs w1_slave file. Since the EEPROM has a limited
 amount of writes (>50k), this command should be used wisely.
 
+Alternatively, resolution can be set or read (value from 9 to 12) using the
+dedicated resolution sysfs entry on each device. This sysfs entry is not
+present for devices not supporting this feature. Driver will adjust the
+correct conversion time for each device regarding to its resolution setting.
+In particular, strong pullup will be applied if required during the conversion
+duration.
+
+The write-only sysfs entry eeprom is an alternative for EEPROM operations:
+  * 'save': will save device RAM to EEPROM
+  * 'restore': will restore EEPROM data in device RAM.
+
+ext_power syfs entry allow tho check the power status of each device.
+  * '0': device parasite powered
+  * '1': device externally powered
+
+sysfs alarms allow read or write TH and TL (Temperature High an Low) alarms.
+Values shall be space separated and in the device range (typical -55 degC
+to 125 degC). Values are integer as they are store in a 8bit register in
+the device. Lowest value is automatically put to TL.Once set, alarms could
+be search at master level.
+
 The module parameter strong_pullup can be set to 0 to disable the
 strong pullup, 1 to enable autodetection or 2 to force strong pullup.
 In case of autodetection, the driver will use the "READ POWER SUPPLY"

MAINTAINERS

@@ -3198,6 +3198,29 @@ N:	bcm2711
 N:	bcm2835
 F:	drivers/staging/vc04_services
 
+BROADCOM BCM2711 HEVC DECODER
+M:	Raspberry Pi Kernel Maintenance <kernel-list@raspberrypi.com>
+L:	linux-media@vger.kernel.org
+S:	Maintained
+F:	Documentation/devicetree/bindings/media/rpivid_hevc.jaml
+F:	drivers/staging/media/rpivid
+
+BROADCOM BCM2835 CAMERA DRIVER
+M:	Raspberry Pi Kernel Maintenance <kernel-list@raspberrypi.com>
+L:	linux-media@vger.kernel.org
+S:	Maintained
+F:	drivers/media/platform/bcm2835/
+F:	Documentation/devicetree/bindings/media/brcm,bcm2835-unicam.yaml
+
+BROADCOM BCM2835 ISP DRIVER
+M:	Raspberry Pi Kernel Maintenance <kernel-list@raspberrypi.com>
+L:	linux-media@vger.kernel.org
+S:	Maintained
+F:	drivers/staging/vc04_services/bcm2835-isp
+F:	include/uapi/linux/bcm2835-isp.h
+F:	Documentation/media/v4l-drivers/bcm2835-isp.rst
+F:	Documentation/media/uapi/v4l/pixfmt-meta-bcm2835-isp-stats.rst
+
 BROADCOM BCM47XX MIPS ARCHITECTURE
 M:	Hauke Mehrtens <hauke@hauke-m.de>
 M:	Rafał Miłecki <zajec5@gmail.com>
@@ -3335,7 +3358,7 @@ L:	linux-i2c@vger.kernel.org
 L:	bcm-kernel-feedback-list@broadcom.com
 S:	Supported
 F:	drivers/i2c/busses/i2c-brcmstb.c
-F:	Documentation/devicetree/bindings/i2c/i2c-brcmstb.txt
+F:	Documentation/devicetree/bindings/i2c/brcm,brcmstb-i2c.yaml
 
 BROADCOM BRCMSTB USB2 and USB3 PHY DRIVER
 M:	Al Cooper <alcooperx@gmail.com>
@@ -4939,6 +4962,24 @@ F:	include/linux/*fence.h
 F:	Documentation/driver-api/dma-buf.rst
 T:	git git://anongit.freedesktop.org/drm/drm-misc
 
+DMA-BUF HEAPS FRAMEWORK
+M:	Sumit Semwal <sumit.semwal@linaro.org>
+R:	Andrew F. Davis <afd@ti.com>
+R:	Benjamin Gaignard <benjamin.gaignard@linaro.org>
+R:	Liam Mark <lmark@codeaurora.org>
+R:	Laura Abbott <labbott@redhat.com>
+R:	Brian Starkey <Brian.Starkey@arm.com>
+R:	John Stultz <john.stultz@linaro.org>
+S:	Maintained
+L:	linux-media@vger.kernel.org
+L:	dri-devel@lists.freedesktop.org
+L:	linaro-mm-sig@lists.linaro.org (moderated for non-subscribers)
+F:	include/uapi/linux/dma-heap.h
+F:	include/linux/dma-heap.h
+F:	drivers/dma-buf/dma-heap.c
+F:	drivers/dma-buf/heaps/*
+T:	git git://anongit.freedesktop.org/drm/drm-misc
+
 DMA GENERIC OFFLOAD ENGINE SUBSYSTEM
 M:	Vinod Koul <vkoul@kernel.org>
 L:	dmaengine@vger.kernel.org
@@ -5559,7 +5600,7 @@ T:	git git://github.com/anholt/linux
 S:	Supported
 F:	drivers/gpu/drm/vc4/
 F:	include/uapi/drm/vc4_drm.h
-F:	Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt
+F:	Documentation/devicetree/bindings/display/brcm,bcm2835-*.yaml
 T:	git git://anongit.freedesktop.org/drm/drm-misc
 
 DRM DRIVERS FOR VIVANTE GPU IP
@@ -15135,6 +15176,14 @@ S:	Maintained
 F:	drivers/media/i2c/imx214.c
 F:	Documentation/devicetree/bindings/media/i2c/sony,imx214.txt
 
+SONY IMX219 SENSOR DRIVER
+M:	Dave Stevenson <dave.stevenson@raspberrypi.com>
+L:	linux-media@vger.kernel.org
+T:	git git://linuxtv.org/media_tree.git
+S:	Maintained
+F:	drivers/media/i2c/imx219.c
+F:	Documentation/devicetree/bindings/media/i2c/imx219.yaml
+
 SONY IMX258 SENSOR DRIVER
 M:	Sakari Ailus <sakari.ailus@linux.intel.com>
 L:	linux-media@vger.kernel.org
@@ -15150,6 +15199,14 @@ S:	Maintained
 F:	drivers/media/i2c/imx274.c
 F:	Documentation/devicetree/bindings/media/i2c/imx274.txt
 
+SONY IMX290 SENSOR DRIVER
+M:	Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
+L:	linux-media@vger.kernel.org
+T:	git git://linuxtv.org/media_tree.git
+S:	Maintained
+F:	drivers/media/i2c/imx290.c
+F:	Documentation/devicetree/bindings/media/i2c/imx290.txt
+
 SONY IMX319 SENSOR DRIVER
 M:	Bingbu Cao <bingbu.cao@intel.com>
 L:	linux-media@vger.kernel.org
@@ -15164,6 +15221,14 @@ T:	git git://linuxtv.org/media_tree.git
 S:	Maintained
 F:	drivers/media/i2c/imx355.c
 
+SONY IMX477 SENSOR DRIVER
+M:	Raspberry Pi Kernel Maintenance <kernel-list@raspberrypi.com>
+L:	linux-media@vger.kernel.org
+T:	git git://linuxtv.org/media_tree.git
+S:	Maintained
+F:	drivers/media/i2c/imx477.c
+F:	Documentation/devicetree/bindings/media/i2c/imx477.yaml
+
 SONY MEMORYSTICK SUBSYSTEM
 M:	Maxim Levitsky <maximlevitsky@gmail.com>
 M:	Alex Dubov <oakad@yahoo.com>

Makefile

@@ -1,7 +1,7 @@
 # SPDX-License-Identifier: GPL-2.0
 VERSION = 5
 PATCHLEVEL = 4
-SUBLEVEL = 42
+SUBLEVEL = 51
 EXTRAVERSION =
 NAME = Kleptomaniac Octopus
 
@@ -587,12 +587,8 @@ KBUILD_MODULES :=
 KBUILD_BUILTIN := 1
 
 # If we have only "make modules", don't compile built-in objects.
-# When we're building modules with modversions, we need to consider
-# the built-in objects during the descend as well, in order to
-# make sure the checksums are up to date before we record them.
-
 ifeq ($(MAKECMDGOALS),modules)
-  KBUILD_BUILTIN := $(if $(CONFIG_MODVERSIONS),1)
+  KBUILD_BUILTIN :=
 endif
 
 # If we have "make <whatever> modules", compile modules
@@ -1245,12 +1241,19 @@ ifneq ($(dtstree),)
 %.dtb: include/config/kernel.release scripts_dtc
 	$(Q)$(MAKE) $(build)=$(dtstree) $(dtstree)/$@
 
+%.dtbo: include/config/kernel.release scripts_dtc
+	$(Q)$(MAKE) $(build)=$(dtstree) $(dtstree)/$@
+
 PHONY += dtbs dtbs_install dtbs_check
-dtbs dtbs_check: include/config/kernel.release scripts_dtc
+dtbs: include/config/kernel.release scripts_dtc
 	$(Q)$(MAKE) $(build)=$(dtstree)
 
+ifneq ($(filter dtbs_check, $(MAKECMDGOALS)),)
+dtbs: dt_binding_check
+endif
+
 dtbs_check: export CHECK_DTBS=1
-dtbs_check: dt_binding_check
+dtbs_check: dtbs
 
 dtbs_install:
 	$(Q)$(MAKE) $(dtbinst)=$(dtstree)
@@ -1278,6 +1281,13 @@ ifdef CONFIG_MODULES
 
 all: modules
 
+# When we're building modules with modversions, we need to consider
+# the built-in objects during the descend as well, in order to
+# make sure the checksums are up to date before we record them.
+ifdef CONFIG_MODVERSIONS
+  KBUILD_BUILTIN := 1
+endif
+
 # Build modules
 #
 # A module can be listed more than once in obj-m resulting in

arch/alpha/include/asm/io.h

@@ -322,14 +322,18 @@ static inline int __is_mmio(const volatile void __iomem *addr)
 #if IO_CONCAT(__IO_PREFIX,trivial_io_bw)
 extern inline unsigned int ioread8(void __iomem *addr)
 {
-	unsigned int ret = IO_CONCAT(__IO_PREFIX,ioread8)(addr);
+	unsigned int ret;
+	mb();
+	ret = IO_CONCAT(__IO_PREFIX,ioread8)(addr);
 	mb();
 	return ret;
 }
 
 extern inline unsigned int ioread16(void __iomem *addr)
 {
-	unsigned int ret = IO_CONCAT(__IO_PREFIX,ioread16)(addr);
+	unsigned int ret;
+	mb();
+	ret = IO_CONCAT(__IO_PREFIX,ioread16)(addr);
 	mb();
 	return ret;
 }
@@ -370,7 +374,9 @@ extern inline void outw(u16 b, unsigned long port)
 #if IO_CONCAT(__IO_PREFIX,trivial_io_lq)
 extern inline unsigned int ioread32(void __iomem *addr)
 {
-	unsigned int ret = IO_CONCAT(__IO_PREFIX,ioread32)(addr);
+	unsigned int ret;
+	mb();
+	ret = IO_CONCAT(__IO_PREFIX,ioread32)(addr);
 	mb();
 	return ret;
 }
@@ -415,14 +421,18 @@ extern inline void __raw_writew(u16 b, volatile void __iomem *addr)
 
 extern inline u8 readb(const volatile void __iomem *addr)
 {
-	u8 ret = __raw_readb(addr);
+	u8 ret;
+	mb();
+	ret = __raw_readb(addr);
 	mb();
 	return ret;
 }
 
 extern inline u16 readw(const volatile void __iomem *addr)
 {
-	u16 ret = __raw_readw(addr);
+	u16 ret;
+	mb();
+	ret = __raw_readw(addr);
 	mb();
 	return ret;
 }
@@ -463,14 +473,18 @@ extern inline void __raw_writeq(u64 b, volatile void __iomem *addr)
 
 extern inline u32 readl(const volatile void __iomem *addr)
 {
-	u32 ret = __raw_readl(addr);
+	u32 ret;
+	mb();
+	ret = __raw_readl(addr);
 	mb();
 	return ret;
 }
 
 extern inline u64 readq(const volatile void __iomem *addr)
 {
-	u64 ret = __raw_readq(addr);
+	u64 ret;
+	mb();
+	ret = __raw_readq(addr);
 	mb();
 	return ret;
 }
@@ -499,14 +513,44 @@ extern inline void writeq(u64 b, volatile void __iomem *addr)
 #define outb_p		outb
 #define outw_p		outw
 #define outl_p		outl
-#define readb_relaxed(addr)	__raw_readb(addr)
-#define readw_relaxed(addr)	__raw_readw(addr)
-#define readl_relaxed(addr)	__raw_readl(addr)
-#define readq_relaxed(addr)	__raw_readq(addr)
-#define writeb_relaxed(b, addr)	__raw_writeb(b, addr)
-#define writew_relaxed(b, addr)	__raw_writew(b, addr)
-#define writel_relaxed(b, addr)	__raw_writel(b, addr)
-#define writeq_relaxed(b, addr)	__raw_writeq(b, addr)
+
+extern u8 readb_relaxed(const volatile void __iomem *addr);
+extern u16 readw_relaxed(const volatile void __iomem *addr);
+extern u32 readl_relaxed(const volatile void __iomem *addr);
+extern u64 readq_relaxed(const volatile void __iomem *addr);
+
+#if IO_CONCAT(__IO_PREFIX,trivial_io_bw)
+extern inline u8 readb_relaxed(const volatile void __iomem *addr)
+{
+	mb();
+	return __raw_readb(addr);
+}
+
+extern inline u16 readw_relaxed(const volatile void __iomem *addr)
+{
+	mb();
+	return __raw_readw(addr);
+}
+#endif
+
+#if IO_CONCAT(__IO_PREFIX,trivial_io_lq)
+extern inline u32 readl_relaxed(const volatile void __iomem *addr)
+{
+	mb();
+	return __raw_readl(addr);
+}
+
+extern inline u64 readq_relaxed(const volatile void __iomem *addr)
+{
+	mb();
+	return __raw_readq(addr);
+}
+#endif
+
+#define writeb_relaxed	writeb
+#define writew_relaxed	writew
+#define writel_relaxed	writel
+#define writeq_relaxed	writeq
 
 /*
  * String version of IO memory access ops:

arch/alpha/kernel/io.c

@@ -16,21 +16,27 @@
 unsigned int
 ioread8(void __iomem *addr)
 {
-	unsigned int ret = IO_CONCAT(__IO_PREFIX,ioread8)(addr);
+	unsigned int ret;
+	mb();
+	ret = IO_CONCAT(__IO_PREFIX,ioread8)(addr);
 	mb();
 	return ret;
 }
 
 unsigned int ioread16(void __iomem *addr)
 {
-	unsigned int ret = IO_CONCAT(__IO_PREFIX,ioread16)(addr);
+	unsigned int ret;
+	mb();
+	ret = IO_CONCAT(__IO_PREFIX,ioread16)(addr);
 	mb();
 	return ret;
 }
 
 unsigned int ioread32(void __iomem *addr)
 {
-	unsigned int ret = IO_CONCAT(__IO_PREFIX,ioread32)(addr);
+	unsigned int ret;
+	mb();
+	ret = IO_CONCAT(__IO_PREFIX,ioread32)(addr);
 	mb();
 	return ret;
 }
@@ -148,28 +154,36 @@ EXPORT_SYMBOL(__raw_writeq);
 
 u8 readb(const volatile void __iomem *addr)
 {
-	u8 ret = __raw_readb(addr);
+	u8 ret;
+	mb();
+	ret = __raw_readb(addr);
 	mb();
 	return ret;
 }
 
 u16 readw(const volatile void __iomem *addr)
 {
-	u16 ret = __raw_readw(addr);
+	u16 ret;
+	mb();
+	ret = __raw_readw(addr);
 	mb();
 	return ret;
 }
 
 u32 readl(const volatile void __iomem *addr)
 {
-	u32 ret = __raw_readl(addr);
+	u32 ret;
+	mb();
+	ret = __raw_readl(addr);
 	mb();
 	return ret;
 }
 
 u64 readq(const volatile void __iomem *addr)
 {
-	u64 ret = __raw_readq(addr);
+	u64 ret;
+	mb();
+	ret = __raw_readq(addr);
 	mb();
 	return ret;
 }
@@ -207,6 +221,38 @@ EXPORT_SYMBOL(writew);
 EXPORT_SYMBOL(writel);
 EXPORT_SYMBOL(writeq);
 
+/*
+ * The _relaxed functions must be ordered w.r.t. each other, but they don't
+ * have to be ordered w.r.t. other memory accesses.
+ */
+u8 readb_relaxed(const volatile void __iomem *addr)
+{
+	mb();
+	return __raw_readb(addr);
+}
+
+u16 readw_relaxed(const volatile void __iomem *addr)
+{
+	mb();
+	return __raw_readw(addr);
+}
+
+u32 readl_relaxed(const volatile void __iomem *addr)
+{
+	mb();
+	return __raw_readl(addr);
+}
+
+u64 readq_relaxed(const volatile void __iomem *addr)
+{
+	mb();
+	return __raw_readq(addr);
+}
+
+EXPORT_SYMBOL(readb_relaxed);
+EXPORT_SYMBOL(readw_relaxed);
+EXPORT_SYMBOL(readl_relaxed);
+EXPORT_SYMBOL(readq_relaxed);
 
 /*
  * Read COUNT 8-bit bytes from port PORT into memory starting at SRC.

arch/arc/kernel/setup.c

@@ -12,6 +12,7 @@
 #include <linux/clocksource.h>
 #include <linux/console.h>
 #include <linux/module.h>
+#include <linux/sizes.h>
 #include <linux/cpu.h>
 #include <linux/of_fdt.h>
 #include <linux/of.h>
@@ -409,12 +410,12 @@ static void arc_chk_core_config(void)
 	if ((unsigned int)__arc_dccm_base != cpu->dccm.base_addr)
 		panic("Linux built with incorrect DCCM Base address\n");
 
-	if (CONFIG_ARC_DCCM_SZ != cpu->dccm.sz)
+	if (CONFIG_ARC_DCCM_SZ * SZ_1K != cpu->dccm.sz)
 		panic("Linux built with incorrect DCCM Size\n");
 #endif
 
 #ifdef CONFIG_ARC_HAS_ICCM
-	if (CONFIG_ARC_ICCM_SZ != cpu->iccm.sz)
+	if (CONFIG_ARC_ICCM_SZ * SZ_1K != cpu->iccm.sz)
 		panic("Linux built with incorrect ICCM Size\n");
 #endif
 

arch/arc/plat-eznps/Kconfig

@@ -6,6 +6,7 @@
 
 menuconfig ARC_PLAT_EZNPS
 	bool "\"EZchip\" ARC dev platform"
+	depends on ISA_ARCOMPACT
 	select CPU_BIG_ENDIAN
 	select CLKSRC_NPS if !PHYS_ADDR_T_64BIT
 	select EZNPS_GIC

arch/arm/boot/compressed/vmlinux.lds.S

@@ -43,7 +43,7 @@ SECTIONS
   }
   .table : ALIGN(4) {
     _table_start = .;
-    LONG(ZIMAGE_MAGIC(2))
+    LONG(ZIMAGE_MAGIC(4))
     LONG(ZIMAGE_MAGIC(0x5a534c4b))
     LONG(ZIMAGE_MAGIC(__piggy_size_addr - _start))
     LONG(ZIMAGE_MAGIC(_kernel_bss_size))

arch/arm/boot/dts/Makefile

@@ -1,4 +1,20 @@
 # SPDX-License-Identifier: GPL-2.0
+
+dtb-$(CONFIG_ARCH_BCM2835) += \
+	bcm2708-rpi-b.dtb \
+	bcm2708-rpi-b-rev1.dtb \
+	bcm2708-rpi-b-plus.dtb \
+	bcm2708-rpi-cm.dtb \
+	bcm2708-rpi-zero.dtb \
+	bcm2708-rpi-zero-w.dtb \
+	bcm2709-rpi-2-b.dtb \
+	bcm2710-rpi-2-b.dtb \
+	bcm2710-rpi-3-b.dtb \
+	bcm2711-rpi-4-b.dtb \
+	bcm2710-rpi-3-b-plus.dtb \
+	bcm2710-rpi-cm3.dtb \
+	bcm2711-rpi-cm4.dtb
+
 dtb-$(CONFIG_ARCH_ALPINE) += \
 	alpine-db.dtb
 dtb-$(CONFIG_MACH_ARTPEC6) += \
@@ -83,6 +99,7 @@ dtb-$(CONFIG_ARCH_BCM2835) += \
 	bcm2837-rpi-3-b.dtb \
 	bcm2837-rpi-3-b-plus.dtb \
 	bcm2837-rpi-cm3-io3.dtb \
+	bcm2711-rpi-4-b.dtb \
 	bcm2835-rpi-zero.dtb \
 	bcm2835-rpi-zero-w.dtb
 dtb-$(CONFIG_ARCH_BCM_5301X) += \
@@ -1303,3 +1320,13 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
 	aspeed-bmc-opp-zaius.dtb \
 	aspeed-bmc-portwell-neptune.dtb \
 	aspeed-bmc-quanta-q71l.dtb
+
+targets += dtbs dtbs_install
+targets += $(dtb-y)
+
+subdir-y	:= overlays
+
+# Enable fixups to support overlays on BCM2835 platforms
+ifeq ($(CONFIG_ARCH_BCM2835),y)
+	DTC_FLAGS ?= -@
+endif

arch/arm/boot/dts/am335x-pocketbeagle.dts

@@ -88,7 +88,6 @@
 			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT3, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_MMC0_CMD, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_MMC0_CLK, PIN_INPUT_PULLUP, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_MCASP0_ACLKR, PIN_INPUT, MUX_MODE4)		/* (B12) mcasp0_aclkr.mmc0_sdwp */
 		>;
 	};
 

arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts

@@ -40,7 +40,7 @@
 
 	ahb {
 		usb0: gadget@300000 {
-			atmel,vbus-gpio = <&pioA PIN_PA27 GPIO_ACTIVE_HIGH>;
+			atmel,vbus-gpio = <&pioA PIN_PB11 GPIO_ACTIVE_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usba_vbus>;
 			status = "okay";
@@ -125,8 +125,6 @@
 			bus-width = <8>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_sdmmc0_default>;
-			non-removable;
-			mmc-ddr-1_8v;
 			status = "okay";
 		};
 

arch/arm/boot/dts/bcm-hr2.dtsi

@@ -75,7 +75,7 @@
 		timer@20200 {
 			compatible = "arm,cortex-a9-global-timer";
 			reg = <0x20200 0x100>;
-			interrupts = <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_PPI 11 IRQ_TYPE_EDGE_RISING>;
 			clocks = <&periph_clk>;
 		};
 
@@ -83,7 +83,7 @@
 			compatible = "arm,cortex-a9-twd-timer";
 			reg = <0x20600 0x20>;
 			interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) |
-						  IRQ_TYPE_LEVEL_HIGH)>;
+						  IRQ_TYPE_EDGE_RISING)>;
 			clocks = <&periph_clk>;
 		};
 
@@ -91,7 +91,7 @@
 			compatible = "arm,cortex-a9-twd-wdt";
 			reg = <0x20620 0x20>;
 			interrupts = <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(1) |
-						  IRQ_TYPE_LEVEL_HIGH)>;
+						  IRQ_TYPE_EDGE_RISING)>;
 			clocks = <&periph_clk>;
 		};
 

arch/arm/boot/dts/bcm-nsp.dtsi

@@ -257,10 +257,10 @@
 			status = "disabled";
 		};
 
-		mailbox: mailbox@25000 {
+		mailbox: mailbox@25c00 {
 			compatible = "brcm,iproc-fa2-mbox";
-			reg = <0x25000 0x445>;
-			interrupts = <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>;
+			reg = <0x25c00 0x400>;
+			interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>;
 			#mbox-cells = <1>;
 			brcm,rx-status-len = <32>;
 			brcm,use-bcm-hdr;

arch/arm/boot/dts/bcm2708-rpi-b-plus.dts

@@ -0,0 +1,128 @@
+/dts-v1/;
+
+#include "bcm2708.dtsi"
+#include "bcm2708-rpi.dtsi"
+#include "bcm283x-rpi-smsc9514.dtsi"
+#include "bcm283x-rpi-csi1-2lane.dtsi"
+#include "bcm283x-rpi-i2c0mux_0_28.dtsi"
+
+/ {
+	compatible = "raspberrypi,model-b-plus", "brcm,bcm2835";
+	model = "Raspberry Pi Model B+";
+};
+
+&gpio {
+	spi0_pins: spi0_pins {
+		brcm,pins = <9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_cs_pins: spi0_cs_pins {
+		brcm,pins = <8 7>;
+		brcm,function = <1>; /* output */
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+
+	i2s_pins: i2s {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	audio_pins: audio_pins {
+		brcm,pins = <40 45>;
+		brcm,function = <4>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
+	cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
+
+	spidev0: spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+
+	spidev1: spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+};
+
+&i2c0if {
+	clock-frequency = <100000>;
+};
+
+&i2c0mux {
+	pinctrl-0 = <&i2c0_pins>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "mmc0";
+		gpios = <&gpio 47 0>;
+	};
+
+	pwr_led: pwr {
+		label = "led1";
+		linux,default-trigger = "input";
+		gpios = <&gpio 35 0>;
+	};
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+};
+
+&audio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&audio_pins>;
+};
+
+/ {
+	__overrides__ {
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+
+		pwr_led_gpio = <&pwr_led>,"gpios:4";
+		pwr_led_activelow = <&pwr_led>,"gpios:8";
+		pwr_led_trigger = <&pwr_led>,"linux,default-trigger";
+	};
+};

arch/arm/boot/dts/bcm2708-rpi-b-rev1.dts

@@ -0,0 +1,127 @@
+/dts-v1/;
+
+#include "bcm2708.dtsi"
+#include "bcm2708-rpi.dtsi"
+#include "bcm283x-rpi-smsc9512.dtsi"
+#include "bcm283x-rpi-csi1-2lane.dtsi"
+
+/ {
+	compatible = "raspberrypi,model-b", "brcm,bcm2835";
+	model = "Raspberry Pi Model B";
+};
+
+&gpio {
+	spi0_pins: spi0_pins {
+		brcm,pins = <9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_cs_pins: spi0_cs_pins {
+		brcm,pins = <8 7>;
+		brcm,function = <1>; /* output */
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+
+	i2s_pins: i2s {
+		brcm,pins = <28 29 30 31>;
+		brcm,function = <6>; /* alt2 */
+	};
+
+	audio_pins: audio_pins {
+		brcm,pins = <40 45>;
+		brcm,function = <4>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
+	cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
+
+	spidev0: spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+
+	spidev1: spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+};
+
+/delete-node/ &i2c0mux;
+
+i2c0: &i2c0if {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	clock-frequency = <100000>;
+};
+
+i2c_csi_dsi: &i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+/ {
+	aliases {
+		i2c0 = &i2c0;
+	};
+
+	__overrides__ {
+		i2c0 = <&i2c0>, "status";
+	};
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "mmc0";
+		gpios = <&gpio 16 1>;
+	};
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
+};
+
+&audio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&audio_pins>;
+};
+
+/ {
+	__overrides__ {
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+	};
+};

arch/arm/boot/dts/bcm2708-rpi-b.dts

@@ -0,0 +1,118 @@
+/dts-v1/;
+
+#include "bcm2708.dtsi"
+#include "bcm2708-rpi.dtsi"
+#include "bcm283x-rpi-smsc9512.dtsi"
+#include "bcm283x-rpi-csi1-2lane.dtsi"
+#include "bcm283x-rpi-i2c0mux_0_28.dtsi"
+
+/ {
+	compatible = "raspberrypi,model-b", "brcm,bcm2835";
+	model = "Raspberry Pi Model B";
+};
+
+&gpio {
+	spi0_pins: spi0_pins {
+		brcm,pins = <9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_cs_pins: spi0_cs_pins {
+		brcm,pins = <8 7>;
+		brcm,function = <1>; /* output */
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+
+	i2s_pins: i2s {
+		brcm,pins = <28 29 30 31>;
+		brcm,function = <6>; /* alt2 */
+	};
+
+	audio_pins: audio_pins {
+		brcm,pins = <40 45>;
+		brcm,function = <4>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
+	cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
+
+	spidev0: spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+
+	spidev1: spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+};
+
+&i2c0if {
+	clock-frequency = <100000>;
+};
+
+&i2c0mux {
+	pinctrl-0 = <&i2c0_pins>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "mmc0";
+		gpios = <&gpio 16 1>;
+	};
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
+};
+
+&audio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&audio_pins>;
+};
+
+/ {
+	__overrides__ {
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+	};
+};

arch/arm/boot/dts/bcm2708-rpi-bt.dtsi

@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: GPL-2.0
+
+&uart0 {
+	bt: bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		max-speed = <3000000>;
+		shutdown-gpios = <&gpio 45 GPIO_ACTIVE_HIGH>;
+		status = "disabled";
+	};
+};
+
+&uart1 {
+	minibt: bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		max-speed = <460800>;
+		shutdown-gpios = <&gpio 45 GPIO_ACTIVE_HIGH>;
+		status = "disabled";
+	};
+};
+
+/ {
+	__overrides__ {
+		krnbt = <&bt>,"status";
+		krnbt_baudrate = <&bt>,"max-speed:0";
+	};
+};

arch/arm/boot/dts/bcm2708-rpi-cm.dts

@@ -0,0 +1,101 @@
+/dts-v1/;
+
+#include "bcm2708-rpi-cm.dtsi"
+#include "bcm283x-rpi-csi0-2lane.dtsi"
+#include "bcm283x-rpi-csi1-4lane.dtsi"
+#include "bcm283x-rpi-i2c0mux_0_28.dtsi"
+
+/ {
+	compatible = "raspberrypi,compute-module", "brcm,bcm2835";
+	model = "Raspberry Pi Compute Module";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&gpio {
+	spi0_pins: spi0_pins {
+		brcm,pins = <9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_cs_pins: spi0_cs_pins {
+		brcm,pins = <8 7>;
+		brcm,function = <1>; /* output */
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+
+	i2s_pins: i2s {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	audio_pins: audio_pins {
+		brcm,pins;
+		brcm,function;
+	};
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
+	cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
+
+	spidev0: spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+
+	spidev1: spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+};
+
+&i2c0if {
+	clock-frequency = <100000>;
+};
+
+&i2c0mux {
+	pinctrl-0 = <&i2c0_pins>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+&audio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&audio_pins>;
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
+};

arch/arm/boot/dts/bcm2708-rpi-cm.dtsi

@@ -0,0 +1,18 @@
+#include "bcm2708.dtsi"
+#include "bcm2708-rpi.dtsi"
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "mmc0";
+		gpios = <&gpio 47 0>;
+	};
+};
+
+/ {
+	__overrides__ {
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+	};
+};

arch/arm/boot/dts/bcm2708-rpi-zero-w.dts

@@ -0,0 +1,167 @@
+/dts-v1/;
+
+#include "bcm2708.dtsi"
+#include "bcm2708-rpi.dtsi"
+#include "bcm283x-rpi-csi1-2lane.dtsi"
+#include "bcm283x-rpi-i2c0mux_0_28.dtsi"
+#include "bcm2708-rpi-bt.dtsi"
+
+/ {
+	compatible = "raspberrypi,model-zero-w", "brcm,bcm2835";
+	model = "Raspberry Pi Zero W";
+
+	chosen {
+		bootargs = "coherent_pool=1M 8250.nr_uarts=1 snd_bcm2835.enable_compat_alsa=0 snd_bcm2835.enable_hdmi=1 snd_bcm2835.enable_headphones=1";
+	};
+
+	aliases {
+		serial0 = &uart1;
+		serial1 = &uart0;
+		mmc1 = &mmcnr;
+	};
+};
+
+&gpio {
+	spi0_pins: spi0_pins {
+		brcm,pins = <9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_cs_pins: spi0_cs_pins {
+		brcm,pins = <8 7>;
+		brcm,function = <1>; /* output */
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+
+	i2s_pins: i2s {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	sdio_pins: sdio_pins {
+		brcm,pins = <34 35 36 37 38 39>;
+		brcm,function = <7>; /* ALT3 = SD1 */
+		brcm,pull = <0 2 2 2 2 2>;
+	};
+
+	bt_pins: bt_pins {
+		brcm,pins = <43>;
+		brcm,function = <4>; /* alt0:GPCLK2 */
+		brcm,pull = <0>; /* none */
+	};
+
+	uart0_pins: uart0_pins {
+		brcm,pins = <30 31 32 33>;
+		brcm,function = <7>; /* alt3=UART0 */
+		brcm,pull = <2 0 0 2>; /* up none none up */
+	};
+
+	uart1_pins: uart1_pins {
+		brcm,pins;
+		brcm,function;
+		brcm,pull;
+	};
+
+	audio_pins: audio_pins {
+		brcm,pins = <>;
+		brcm,function = <>;
+	};
+};
+
+&mmcnr {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdio_pins>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins &bt_pins>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
+	cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
+
+	spidev0: spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+
+	spidev1: spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+};
+
+&i2c0if {
+	clock-frequency = <100000>;
+};
+
+&i2c0mux {
+	pinctrl-0 = <&i2c0_pins>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "actpwr";
+		gpios = <&gpio 47 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+};
+
+&audio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&audio_pins>;
+};
+
+/ {
+	__overrides__ {
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+	};
+};

arch/arm/boot/dts/bcm2708-rpi-zero.dts

@@ -0,0 +1,121 @@
+/dts-v1/;
+
+#include "bcm2708.dtsi"
+#include "bcm2708-rpi.dtsi"
+#include "bcm283x-rpi-csi1-2lane.dtsi"
+#include "bcm283x-rpi-i2c0mux_0_28.dtsi"
+
+/ {
+	compatible = "raspberrypi,model-zero", "brcm,bcm2835";
+	model = "Raspberry Pi Zero";
+
+	chosen {
+		bootargs = "coherent_pool=1M snd_bcm2835.enable_compat_alsa=0 snd_bcm2835.enable_hdmi=1 snd_bcm2835.enable_headphones=1";
+	};
+};
+
+&gpio {
+	spi0_pins: spi0_pins {
+		brcm,pins = <9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_cs_pins: spi0_cs_pins {
+		brcm,pins = <8 7>;
+		brcm,function = <1>; /* output */
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+
+	i2s_pins: i2s {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	audio_pins: audio_pins {
+		brcm,pins = <>;
+		brcm,function = <>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
+	cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
+
+	spidev0: spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+
+	spidev1: spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+};
+
+&i2c0if {
+	clock-frequency = <100000>;
+};
+
+&i2c0mux {
+	pinctrl-0 = <&i2c0_pins>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "actpwr";
+		gpios = <&gpio 47 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+};
+
+&audio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&audio_pins>;
+};
+
+/ {
+	__overrides__ {
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+	};
+};

arch/arm/boot/dts/bcm2708-rpi.dtsi

@@ -0,0 +1,36 @@
+/* Downstream modifications common to bcm2835, bcm2836, bcm2837 */
+
+#include "bcm2835-rpi.dtsi"
+#include "bcm270x-rpi.dtsi"
+
+/ {
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0>;
+	};
+
+	aliases {
+		i2c2 = &i2c2;
+	};
+
+	__overrides__ {
+		i2c2_iknowwhatimdoing = <&i2c2>,"status";
+		i2c2_baudrate = <&i2c2>,"clock-frequency:0";
+		sd_poll_once = <&sdhost>, "non-removable?";
+	};
+};
+
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	status = "okay";
+};
+
+&hdmi {
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "disabled";
+};
+
+&i2c2 {
+	status = "disabled";
+};

arch/arm/boot/dts/bcm2708.dtsi

@@ -0,0 +1,14 @@
+#include "bcm2835.dtsi"
+#include "bcm270x.dtsi"
+
+/ {
+	/delete-node/ cpus;
+
+	__overrides__ {
+		arm_freq;
+	};
+};
+
+&vc4 {
+	status = "disabled";
+};

arch/arm/boot/dts/bcm2709-rpi-2-b.dts

@@ -0,0 +1,128 @@
+/dts-v1/;
+
+#include "bcm2709.dtsi"
+#include "bcm2709-rpi.dtsi"
+#include "bcm283x-rpi-smsc9514.dtsi"
+#include "bcm283x-rpi-csi1-2lane.dtsi"
+#include "bcm283x-rpi-i2c0mux_0_28.dtsi"
+
+/ {
+	compatible = "raspberrypi,2-model-b", "brcm,bcm2836";
+	model = "Raspberry Pi 2 Model B";
+};
+
+&gpio {
+	spi0_pins: spi0_pins {
+		brcm,pins = <9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_cs_pins: spi0_cs_pins {
+		brcm,pins = <8 7>;
+		brcm,function = <1>; /* output */
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+
+	i2s_pins: i2s {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	audio_pins: audio_pins {
+		brcm,pins = <40 45>;
+		brcm,function = <4>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
+	cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
+
+	spidev0: spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+
+	spidev1: spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+};
+
+&i2c0if {
+	clock-frequency = <100000>;
+};
+
+&i2c0mux {
+	pinctrl-0 = <&i2c0_pins>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "mmc0";
+		gpios = <&gpio 47 0>;
+	};
+
+	pwr_led: pwr {
+		label = "led1";
+		linux,default-trigger = "input";
+		gpios = <&gpio 35 0>;
+	};
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+};
+
+&audio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&audio_pins>;
+};
+
+/ {
+	__overrides__ {
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+
+		pwr_led_gpio = <&pwr_led>,"gpios:4";
+		pwr_led_activelow = <&pwr_led>,"gpios:8";
+		pwr_led_trigger = <&pwr_led>,"linux,default-trigger";
+	};
+};