This fix keeps the driver from loading the headphone controls in case they are
not defined in the selected device tree overlay. This avoids problems if a
device uses the same I2C bus address as the headphone amp. The driver issues a
warning in that case.
Adds the missing embedded newlines in some printk/info statements.
Signed-off-by: Joerg Schambacher <joerg@hifiberry.com>
Adds 2 msecs delay when switching between oscillators to allow
correct PLL settling.
Thanks to Clive Messer for the support!
Signed-off-by: Joerg Schambacher <joerg@hifiberry.com>
Adds the necessary GPIO handling and ALSA mixer extensions.
Also fixes a problem with the PLL/CLK control when switching sample rates.
Thanks to Clive Messer for the support!
Signed-off-by: Joerg Schambacher <joerg@hifiberry.com>
Commit 0a038c1c29 ("drm/vc4: Move LBM creation out of
vc4_plane_mode_set()") changed the LBM allocation logic from first
allocating the LBM memory for the plane to running mode_set,
adding a gap in the LBM, and then running the dlist allocation filling
that gap.
The gap was introduced by incrementing the dlist array index, but was
never checking whether or not we were over the array length, leading
eventually to memory corruptions if we ever crossed this limit.
vc4_dlist_write had that logic though, and was reallocating a larger
dlist array when reaching the end of the buffer. Let's share the logic
between both functions.
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: Eric Anholt <eric@anholt.net>
Fixes: 0a038c1c29 ("drm/vc4: Move LBM creation out of vc4_plane_mode_set()")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Much effort has been put into finding ways to avoid warnings from dtc
about overlays, usually to do with the presence of #address-cells and
size-cells, but not exclusively so. Since the issues being warned about
are harmless, suppress the warnings to declutter the build output and
to avoid alarming users.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Add colour denoise control to the bcm2835 driver through a new v4l2
control: V4L2_CID_USER_BCM2835_ISP_CDN.
Add the accompanying MMAL configuration structure definitions as well.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
It turns out the used CAN SPI chip is not a good way to identify the version of
the CAN HAT.
There are two different board layouts of the Seeed Studio CAN BUS FD HAT. The
v1 board doesn't have a battery holder, while the v2 board has. Update the
overlay README accordinly.
Link: https://github.com/Seeed-Studio/seeed-linux-dtoverlays/issues/13
Cc: Patrick Menschel <menschel.p@posteo.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds the overlay for the Seeed Studio CAN BUS FD HAT v1 with two CAN
FD Channels (based on mcp2517fd).
https://www.seeedstudio.com/2-Channel-CAN-BUS-FD-Shield-for-Raspberry-Pi-p-4072.html
The overlay was generated by:
ovmerge -c spi1-1cs-overlay.dts,cs0_pin=18,cs0_spidev=false \
mcp251xfd-overlay.dts,spi0-0,interrupt=25 \
mcp251xfd-overlay.dts,spi1-0,interrupt=24
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There are several versions of the Seeed Studio CAN BUS FD HAT. This is the
second version, based on the mcp2518fd, so give it a -v2 postfix.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds the overlay for the Seeed Studio CAN BUS FD HAT
with two CAN FD Channels and an RTC.
https://www.seeedstudio.com/CAN-BUS-FD-HAT-for-Raspberry-Pi-p-4742.html
The overlay was generated by
ovmerge -c mcp251xfd-overlay.dts,spi0-0,interrupt=25 \
mcp251xfd-overlay.dts,spi0-1,interrupt=24 \
i2c-rtc-overlay.dts,pcf85063
Also, add description on how to generate overlays
Signed-off-by: Patrick Menschel <menschel.p@posteo.de>
To comply with the intended usage of the V4L2 selection target when
used to retrieve a sensor image properties, adjust the rectangles
returned by the ov5647 driver.
The top/left crop coordinates of the TGT_CROP rectangle were set to
(0, 0) instead of (16, 16) which is the offset from the larger physical
pixel array rectangle. This was also a mismatch with the default values
crop rectangle value, so this is corrected. Found with v4l2-compliance.
While at it, add V4L2_SEL_TGT_CROP_BOUNDS support: CROP_DEFAULT and
CROP_BOUNDS have the same size as the non-active pixels are not readable
using the selection API. Found with v4l2-compliance.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
The overlays for the ads1015 and ads1115 I2C ADCs omitted the addresses
in the main device node names. As well as breaking the conventions for
I2C devices, this prevents the firmware from renaming them when the
"reg" property is modified, which in turn stops the overlays from being
instantiated multiple times.
See: https://www.raspberrypi.org/forums/viewtopic.php?f=107&t=294465
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The mpu6050 starts up at address 0x68 by default, but can be set to
0x69 if the ADO pin is pulled high. Give the overlay an addr parameter
to allow devices at the alternate address to be used.
See: https://github.com/Hexxeh/rpi-firmware/issues/252
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
lan78xx_link_reset explicitly clears the MAC's view of the PHY's IRQ
status. In doing so it potentially leaves the PHY with a pending
interrupt that will never be acknowledged, at which point no further
interrupts will be generated.
Avoid the problem by acknowledging any pending PHY interrupt after
clearing the MAC's status bit.
See: https://github.com/raspberrypi/linux/issues/2937
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
commit 3c78e9e0d3 upstream.
This patch adds nft_flow_rule_set_addr_type() to set the address type
from the nft_payload expression accordingly.
If the address type is not set in the control dissector then a rule that
matches either on source or destination IP address does not work.
After this patch, nft hardware offload generates the flow dissector
configuration as tc-flower does to match on an IP address.
This patch has been also tested functionally to make sure packets are
filtered out by the NIC.
This is also getting the code aligned with the existing netfilter flow
offload infrastructure which is also setting the control dissector.
Fixes: c9626a2cbd ("netfilter: nf_tables: add hardware offload support")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c0700dfa2c upstream.
There are reports wrt lockdep splat in nftables, e.g.:
------------[ cut here ]------------
WARNING: CPU: 2 PID: 31416 at net/netfilter/nf_tables_api.c:622
lockdep_nfnl_nft_mutex_not_held+0x28/0x38 [nf_tables]
...
These are caused by an earlier, unrelated bug such as a n ABBA deadlock
in a different subsystem.
In such an event, lockdep is disabled and lockdep_is_held returns true
unconditionally. This then causes the WARN() in nf_tables.
Make the WARN conditional on lockdep still active to avoid this.
Fixes: f102d66b33 ("netfilter: nf_tables: use dedicated mutex to guard transactions")
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Link: https://lore.kernel.org/linux-kselftest/CA+G9fYvFUpODs+NkSYcnwKnXm62tmP=ksLeBPmB+KFrB2rvCtQ@mail.gmail.com/
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 857c4c0a8b upstream.
Building on arch/s390/ results in this build error:
cc1: some warnings being treated as errors
../drivers/md/dm-writecache.c: In function 'persistent_memory_claim':
../drivers/md/dm-writecache.c:323:1: error: no return statement in function returning non-void [-Werror=return-type]
Fix this by replacing the BUG() with an -EOPNOTSUPP return.
Fixes: 48debafe4f ("dm: add writecache target")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d966ddcc38 upstream.
In the commit fdeba99b1e
("tipc: fix use-after-free in tipc_bcast_get_mode"), we're trying
to make sure the tipc_net_finalize_work work item finished if it
enqueued. But calling flush_scheduled_work() is not just affecting
above work item but either any scheduled work. This has turned out
to be overkill and caused to deadlock as syzbot reported:
======================================================
WARNING: possible circular locking dependency detected
5.9.0-rc2-next-20200828-syzkaller #0 Not tainted
------------------------------------------------------
kworker/u4:6/349 is trying to acquire lock:
ffff8880aa063d38 ((wq_completion)events){+.+.}-{0:0}, at: flush_workqueue+0xe1/0x13e0 kernel/workqueue.c:2777
but task is already holding lock:
ffffffff8a879430 (pernet_ops_rwsem){++++}-{3:3}, at: cleanup_net+0x9b/0xb10 net/core/net_namespace.c:565
[...]
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(pernet_ops_rwsem);
lock(&sb->s_type->i_mutex_key#13);
lock(pernet_ops_rwsem);
lock((wq_completion)events);
*** DEADLOCK ***
[...]
v1:
To fix the original issue, we replace above calling by introducing
a bit flag. When a namespace cleaned-up, bit flag is set to zero and:
- tipc_net_finalize functionial just does return immediately.
- tipc_net_finalize_work does not enqueue into the scheduled work queue.
v2:
Use cancel_work_sync() helper to make sure ONLY the
tipc_net_finalize_work() stopped before releasing bcbase object.
Reported-by: syzbot+d5aa7e0385f6a5d0f4fd@syzkaller.appspotmail.com
Fixes: fdeba99b1e ("tipc: fix use-after-free in tipc_bcast_get_mode")
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Hoang Huu Le <hoang.h.le@dektech.com.au>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 778721510e upstream.
If gfs2 tries to mount a (corrupt) file system that has no resource
groups it still tries to set preferences on the first one, which causes
a kernel null pointer dereference. This patch adds a check to function
gfs2_ri_update so this condition is detected and reported back as an
error.
Reported-by: syzbot+e3f23ce40269a4c9053a@syzkaller.appspotmail.com
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f134b89a2 upstream.
Lilith >_> and Claudio Bozzato of Cisco Talos security team reported
that collect_syscall() improperly casts the syscall registers to 64-bit
values leaking the uninitialized last 24 bytes on 32-bit platforms, that
are visible in /proc/self/syscall.
The cause is that info->data.args are u64 while syscall_get_arguments()
uses longs, as hinted by the bogus pointer cast in the function.
Let's just proceed like the other call places, by retrieving the
registers into an array of longs before assigning them to the caller's
array. This was successfully tested on x86_64, i386 and ppc32.
Reference: CVE-2020-28588, TALOS-2020-1211
Fixes: 631b7abacd ("ptrace: Remove maxargs from task_current_syscall()")
Cc: Greg KH <greg@kroah.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Tested-by: Michael Ellerman <mpe@ellerman.id.au> (ppc32)
Signed-off-by: Willy Tarreau <w@1wt.eu>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bcee527895 upstream.
When the instances were able to use their own options, the userstacktrace
option was left hardcoded for the top level. This made the instance
userstacktrace option bascially into a nop, and will confuse users that set
it, but nothing happens (I was confused when it happened to me!)
Cc: stable@vger.kernel.org
Fixes: 16270145ce ("tracing: Add trace options for core options to instances")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1de67a3dee upstream.
Arbitration Lost (IAL) can happen after every single byte transfer. If
arbitration is lost, the I2C hardware will autonomously switch from
master mode to slave. If a transfer is not aborted in this state,
consecutive transfers will not be executed by the hardware and will
timeout.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Tested (not extensively) on Vybrid VF500 (Toradex VF50):
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 384a9565f7 upstream.
According to the "VFxxx Controller Reference Manual" (and the comment
block starting at line 97), Vybrid requires writing a one for clearing
an interrupt flag. Syncing the method for clearing I2SR_IIF in
i2c_imx_isr().
Signed-off-by: Christian Eggers <ceggers@arri.de>
Fixes: 4b775022f6 ("i2c: imx: add struct to hold more configurable quirks")
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8199be001a upstream.
When investigating a slab cache bloat problem, significant amount of
negative dentry cache was seen, but confusingly they neither got shrunk
by reclaimer (the host has very tight memory) nor be shrunk by dropping
cache. The vmcore shows there are over 14M negative dentry objects on
lru, but tracing result shows they were even not scanned at all.
Further investigation shows the memcg's vfs shrinker_map bit is not set.
So the reclaimer or dropping cache just skip calling vfs shrinker. So
we have to reboot the hosts to get the memory back.
I didn't manage to come up with a reproducer in test environment, and
the problem can't be reproduced after rebooting. But it seems there is
race between shrinker map bit clear and reparenting by code inspection.
The hypothesis is elaborated as below.
The memcg hierarchy on our production environment looks like:
root
/ \
system user
The main workloads are running under user slice's children, and it
creates and removes memcg frequently. So reparenting happens very often
under user slice, but no task is under user slice directly.
So with the frequent reparenting and tight memory pressure, the below
hypothetical race condition may happen:
CPU A CPU B
reparent
dst->nr_items == 0
shrinker:
total_objects == 0
add src->nr_items to dst
set_bit
return SHRINK_EMPTY
clear_bit
child memcg offline
replace child's kmemcg_id with
parent's (in memcg_offline_kmem())
list_lru_del() between shrinker runs
see parent's kmemcg_id
dec dst->nr_items
reparent again
dst->nr_items may go negative
due to concurrent list_lru_del()
The second run of shrinker:
read nr_items without any
synchronization, so it may
see intermediate negative
nr_items then total_objects
may return 0 coincidently
keep the bit cleared
dst->nr_items != 0
skip set_bit
add scr->nr_item to dst
After this point dst->nr_item may never go zero, so reparenting will not
set shrinker_map bit anymore. And since there is no task under user
slice directly, so no new object will be added to its lru to set the
shrinker map bit either. That bit is kept cleared forever.
How does list_lru_del() race with reparenting? It is because reparenting
replaces children's kmemcg_id to parent's without protecting from
nlru->lock, so list_lru_del() may see parent's kmemcg_id but actually
deleting items from child's lru, but dec'ing parent's nr_items, so the
parent's nr_items may go negative as commit 2788cf0c40 ("memcg:
reparent list_lrus and free kmemcg_id on css offline") says.
Since it is impossible that dst->nr_items goes negative and
src->nr_items goes zero at the same time, so it seems we could set the
shrinker map bit iff src->nr_items != 0. We could synchronize
list_lru_count_one() and reparenting with nlru->lock, but it seems
checking src->nr_items in reparenting is the simplest and avoids lock
contention.
Fixes: fae91d6d8b ("mm/list_lru.c: set bit in memcg shrinker bitmap on first list_lru item appearance")
Suggested-by: Roman Gushchin <guro@fb.com>
Signed-off-by: Yang Shi <shy828301@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Roman Gushchin <guro@fb.com>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: <stable@vger.kernel.org> [4.19]
Link: https://lkml.kernel.org/r/20201202171749.264354-1-shy828301@gmail.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bde3808bc8 upstream.
Fixes sparse warnings:
drivers/md/dm.c:508:12: warning: context imbalance in 'dm_prepare_ioctl' - wrong count at exit
drivers/md/dm.c:543:13: warning: context imbalance in 'dm_unprepare_ioctl' - wrong count at exit
Fixes: 971888c469 ("dm: hold DM table for duration of ioctl rather than use blkdev_get")
Cc: stable@vger.kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9ea69a55b3 upstream.
With virtio multiqueue, normally each queue IRQ is mapped to a CPU.
Commit 0d9f0a52c8 ("virtio_scsi: use virtio IRQ affinity") exposed
an existing shortcoming of the arch code by moving virtio_scsi to
the automatic IRQ affinity assignment.
The affinity is correctly computed in msi_desc but this is not applied
to the system IRQs.
It appears the affinity is correctly passed to rtas_setup_msi_irqs() but
lost at this point and never passed to irq_domain_alloc_descs()
(see commit 06ee6d571f ("genirq: Add affinity hint to irq allocation"))
because irq_create_mapping() doesn't take an affinity parameter.
Use the new irq_create_mapping_affinity() function, which allows to forward
the affinity setting from rtas_setup_msi_irqs() to irq_domain_alloc_descs().
With this change, the virtqueues are correctly dispatched between the CPUs
on pseries.
Fixes: e75eafb9b0 ("genirq/msi: Switch to new irq spreading infrastructure")
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Greg Kurz <groug@kaod.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20201126082852.1178497-3-lvivier@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb4c6910c8 upstream.
There is currently no way to convey the affinity of an interrupt
via irq_create_mapping(), which creates issues for devices that
expect that affinity to be managed by the kernel.
In order to sort this out, rename irq_create_mapping() to
irq_create_mapping_affinity() with an additional affinity parameter that
can be passed down to irq_domain_alloc_descs().
irq_create_mapping() is re-implemented as a wrapper around
irq_create_mapping_affinity().
No functional change.
Fixes: e75eafb9b0 ("genirq/msi: Switch to new irq spreading infrastructure")
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Greg Kurz <groug@kaod.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20201126082852.1178497-2-lvivier@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67aa3ec3db upstream.
Advance the maximum number of arguments to 16.
This fixes issue where certain operations, combined with table
configured args, exceed 10 arguments.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Fixes: 48debafe4f ("dm: add writecache target")
Cc: stable@vger.kernel.org # v4.18+
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 600c0849cf upstream.
Paulian reported a crash that happens when a dock is unplugged during
hibernation:
[78436.228217] thunderbolt 0-1: device disconnected
[78436.228365] BUG: kernel NULL pointer dereference, address: 00000000000001e0
...
[78436.228397] RIP: 0010:icm_free_unplugged_children+0x109/0x1a0
...
[78436.228432] Call Trace:
[78436.228439] icm_rescan_work+0x24/0x30
[78436.228444] process_one_work+0x1a3/0x3a0
[78436.228449] worker_thread+0x30/0x370
[78436.228454] ? process_one_work+0x3a0/0x3a0
[78436.228457] kthread+0x13d/0x160
[78436.228461] ? kthread_park+0x90/0x90
[78436.228465] ret_from_fork+0x1f/0x30
This happens because remove_unplugged_switch() calls tb_switch_remove()
that releases the memory pointed by sw so the following lines reference
to a memory that might be released already.
Fix this by saving pointer to the parent device before calling
tb_switch_remove().
Reported-by: Paulian Bogdan Marinca <paulian@marinca.net>
Fixes: 4f7c2e0d87 ("thunderbolt: Make sure device runtime resume completes before taking domain lock")
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61e6fe59ed upstream.
If arbitration is lost, the master automatically changes to slave mode.
I2SR_IBB may or may not be reset by hardware. Raising a STOP condition
by resetting I2CR_MSTA has no effect and will not clear I2SR_IBB.
So calling i2c_imx_bus_busy() is not required and would busy-wait until
timeout.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Tested (not extensively) on Vybrid VF500 (Toradex VF50):
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: stable@vger.kernel.org # Requires trivial backporting, simple remove
# the 3rd argument from the calls to
# i2c_imx_bus_busy().
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6988a619f5 upstream.
A customer has reported that several files in their multi-threaded app
were left with size of 0 because most of the read(2) calls returned
-EINTR and they assumed no bytes were read. Obviously, they could
have fixed it by simply retrying on -EINTR.
We noticed that most of the -EINTR on read(2) were due to real-time
signals sent by glibc to process wide credential changes (SIGRT_1),
and its signal handler had been established with SA_RESTART, in which
case those calls could have been automatically restarted by the
kernel.
Let the kernel decide to whether or not restart the syscalls when
there is a signal pending in __smb_send_rqst() by returning
-ERESTARTSYS. If it can't, it will return -EINTR anyway.
Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
CC: Stable <stable@vger.kernel.org>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c75b0ff4e upstream.
On powerpc, kprobe-direct.tc triggered FTRACE_WARN_ON() in
ftrace_get_addr_new() followed by the below message:
Bad trampoline accounting at: 000000004222522f (wake_up_process+0xc/0x20) (f0000001)
The set of steps leading to this involved:
- modprobe ftrace-direct-too
- enable_probe
- modprobe ftrace-direct
- rmmod ftrace-direct <-- trigger
The problem turned out to be that we were not updating flags in the
ftrace record properly. From the above message about the trampoline
accounting being bad, it can be seen that the ftrace record still has
FTRACE_FL_TRAMP set though ftrace-direct module is going away. This
happens because we are checking if any ftrace_ops has the
FTRACE_FL_TRAMP flag set _before_ updating the filter hash.
The fix for this is to look for any _other_ ftrace_ops that also needs
FTRACE_FL_TRAMP.
Link: https://lkml.kernel.org/r/56c113aa9c3e10c19144a36d9684c7882bf09af5.1606412433.git.naveen.n.rao@linux.vnet.ibm.com
Cc: stable@vger.kernel.org
Fixes: a124692b69 ("ftrace: Enable trampoline when rec count returns back to one")
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 242d990c15 upstream.
The generic parser accepts the preferred_dacs[] pairs as a hint for
assigning a DAC to each pin, but this hint doesn't work always
effectively. Currently it's merely a secondary choice after the trial
with the path index failed. This made sometimes it difficult to
assign DACs without mimicking the connection list and/or the badness
table.
This patch adds a new flag, obey_preferred_dacs, that changes the
behavior of the parser. As its name stands, the parser obeys the
given preferred_dacs[] pairs by skipping the path index matching and
giving a high penalty if no DAC is assigned by the pairs. This mode
will help for assigning the fixed DACs forcibly from the codec
driver.
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201127141104.11041-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c84bfedce6 upstream.
ASUS Zephyrus G14 has two speaker pins, and the auto-parser tries to
assign an individual DAC to each pin as much as possible.
Unfortunately the third DAC has no volume control unlike the two DACs,
and this resulted in the inconsistent speaker volumes.
As a workaround, wire both speaker pins to the same DAC by modifying
the existing quirk (ALC289_FIXUP_ASUS_GA401) applied to this device.
Since this quirk entry is chained by another, we need to avoid
applying the DAC assignment change for it. Luckily, there is another
quirk entry (ALC289_FIXUP_ASUS_GA502) doing the very same thing, so we
can chain to the GA502 quirk instead.
Note that this patch uses a new flag of the generic parser,
obey_preferred_dacs, for enforcing the DACs.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=210359
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201127141104.11041-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c8bcd9c5be upstream.
Currently, locking of ->session is very inconsistent; most places
protect it using the legacy tty mutex, but disassociate_ctty(),
__do_SAK(), tiocspgrp() and tiocgsid() don't.
Two of the writers hold the ctrl_lock (because they already need it for
->pgrp), but __proc_set_tty() doesn't do that yet.
On a PREEMPT=y system, an unprivileged user can theoretically abuse
this broken locking to read 4 bytes of freed memory via TIOCGSID if
tiocgsid() is preempted long enough at the right point. (Other things
might also go wrong, especially if root-only ioctls are involved; I'm
not sure about that.)
Change the locking on ->session such that:
- tty_lock() is held by all writers: By making disassociate_ctty()
hold it. This should be fine because the same lock can already be
taken through the call to tty_vhangup_session().
The tricky part is that we need to shorten the area covered by
siglock to be able to take tty_lock() without ugly retry logic; as
far as I can tell, this should be fine, since nothing in the
signal_struct is touched in the `if (tty)` branch.
- ctrl_lock is held by all writers: By changing __proc_set_tty() to
hold the lock a little longer.
- All readers that aren't holding tty_lock() hold ctrl_lock: By
adding locking to tiocgsid() and __do_SAK(), and expanding the area
covered by ctrl_lock in tiocspgrp().
Cc: stable@kernel.org
Signed-off-by: Jann Horn <jannh@google.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54ffccbf05 upstream.
tiocspgrp() takes two tty_struct pointers: One to the tty that userspace
passed to ioctl() (`tty`) and one to the TTY being changed (`real_tty`).
These pointers are different when ioctl() is called with a master fd.
To properly lock real_tty->pgrp, we must take real_tty->ctrl_lock.
This bug makes it possible for racing ioctl(TIOCSPGRP, ...) calls on
both sides of a PTY pair to corrupt the refcount of `struct pid`,
leading to use-after-free errors.
Fixes: 47f86834bb ("redo locking of tty->pgrp")
CC: stable@kernel.org
Signed-off-by: Jann Horn <jannh@google.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c98fff7332 upstream.
This is a partial revert of commit 2bb70f0a4b ("USB: serial:
option: support dynamic Quectel USB compositions")
The Quectel BG96 is different from most other modern Quectel modems,
having serial functions with 3 endpoints using ff/ff/ff and ff/fe/ff
class/subclass/protocol. Including it in the change to accommodate
dynamic function mapping was incorrect.
Revert to interface number matching for the BG96, assuming static
layout of the RMNET function on interface 4. This restores support
for the serial functions on interfaces 2 and 3.
Full lsusb output for the BG96:
Bus 002 Device 003: ID 2c7c:0296
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x2c7c
idProduct 0x0296
bcdDevice 0.00
iManufacturer 3 Qualcomm, Incorporated
iProduct 2 Qualcomm CDMA Technologies MSM
iSerial 4 d1098243
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 145
bNumInterfaces 5
bConfigurationValue 1
iConfiguration 1 Qualcomm Configuration
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 2
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 5
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x84 EP 4 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 3
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 254
bInterfaceProtocol 255
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x85 EP 5 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 5
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x86 EP 6 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 4
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x87 EP 7 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 5
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x88 EP 8 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x05 EP 5 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)
Cc: Sebastian Sjoholm <sebastian.sjoholm@gmail.com>
Fixes: 2bb70f0a4b ("USB: serial: option: support dynamic Quectel USB compositions")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 156abe2961 upstream
The pins on the Bay Trail SoC have separate input-buffer and output-buffer
enable bits and a read of the level bit of the value register will always
return the value from the input-buffer.
The BIOS of a device may configure a pin in output-only mode, only enabling
the output buffer, and write 1 to the level bit to drive the pin high.
This 1 written to the level bit will be stored inside the data-latch of the
output buffer.
But a subsequent read of the value register will return 0 for the level bit
because the input-buffer is disabled. This causes a read-modify-write as
done by byt_gpio_set_direction() to write 0 to the level bit, driving the
pin low!
Before this commit byt_gpio_direction_output() relied on
pinctrl_gpio_direction_output() to set the direction, followed by a call
to byt_gpio_set() to apply the selected value. This causes the pin to
go low between the pinctrl_gpio_direction_output() and byt_gpio_set()
calls.
Change byt_gpio_direction_output() to directly make the register
modifications itself instead. Replacing the 2 subsequent writes to the
value register with a single write.
Note that the pinctrl code does not keep track internally of the direction,
so not going through pinctrl_gpio_direction_output() is not an issue.
This issue was noticed on a Trekstor SurfTab Twin 10.1. When the panel is
already on at boot (no external monitor connected), then the i915 driver
does a gpiod_get(..., GPIOD_OUT_HIGH) for the panel-enable GPIO. The
temporarily going low of that GPIO was causing the panel to reset itself
after which it would not show an image until it was turned off and back on
again (until a full modeset was done on it). This commit fixes this.
This commit also updates the byt_gpio_direction_input() to use direct
register accesses instead of going through pinctrl_gpio_direction_input(),
to keep it consistent with byt_gpio_direction_output().
Note for backporting, this commit depends on:
commit e2b74419e5 ("pinctrl: baytrail: Replace WARN with dev_info_once
when setting direct-irq pin to output")
Cc: stable@vger.kernel.org
Fixes: 86e3ef812f ("pinctrl: baytrail: Update gpio chip operations")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[sudip: use byt_gpio and vg->pdev->dev for dev_info()]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e2b74419e5 upstream
Suspending Goodix touchscreens requires changing the interrupt pin to
output before sending them a power-down command. Followed by wiggling
the interrupt pin to wake the device up, after which it is put back
in input mode.
On Cherry Trail device the interrupt pin is listed as a GpioInt ACPI
resource so we can do this without problems as long as we release the
IRQ before changing the pin to output mode.
On Bay Trail devices with a Goodix touchscreen direct-irq mode is used
in combination with listing the pin as a normal GpioIo resource. This
works fine, but this triggers the WARN in byt_gpio_set_direction-s output
path because direct-irq support is enabled on the pin.
This commit replaces the WARN call with a dev_info_once call, fixing a
bunch of WARN splats in dmesg on each suspend/resume cycle.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
To comply with the intended usage of the V4L2 selection target when
used to retrieve a sensor image properties, adjust the rectangles
returned by the imx477 driver.
The top/left crop coordinates of the TGT_CROP rectangle were set to
(0, 0) instead of (8, 16) which is the offset from the larger physical
pixel array rectangle. This was also a mismatch with the default values
crop rectangle value, so this is corrected. Found with v4l2-compliance.
While at it, add V4L2_SEL_TGT_CROP_BOUNDS support: CROP_DEFAULT and
CROP_BOUNDS have the same size as the non-active pixels are not readable
using the selection API. Found with v4l2-compliance.
This commit mirrors 543790f777 done for
the imx219 sensor.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
commit 2ed381439e upstream.
i40iw_mmap manipulates the vma->vm_pgoff to differentiate a push page mmap
vs a doorbell mmap, and uses it to compute the pfn in remap_pfn_range
without any validation. This is vulnerable to an mmap exploit as described
in: https://lore.kernel.org/r/20201119093523.7588-1-zhudi21@huawei.com
The push feature is disabled in the driver currently and therefore no push
mmaps are issued from user-space. The feature does not work as expected in
the x722 product.
Remove the push module parameter and all VMA attribute manipulations for
this feature in i40iw_mmap. Update i40iw_mmap to only allow DB user
mmapings at offset = 0. Check vm_pgoff for zero and if the mmaps are bound
to a single page.
Cc: <stable@kernel.org>
Fixes: d374984179 ("i40iw: add files for iwarp interface")
Link: https://lore.kernel.org/r/20201125005616.1800-2-shiraz.saleem@intel.com
Reported-by: Di Zhu <zhudi21@huawei.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 310e3a4b5a upstream.
This patch reverts commit 978defee11 ("tracing: Do a WARN_ON()
if start_thread() in hwlat is called when thread exists")
.start hook can be legally called several times if according
tracer is stopped
screen window 1
[root@localhost ~]# echo 1 > /sys/kernel/tracing/events/kmem/kfree/enable
[root@localhost ~]# echo 1 > /sys/kernel/tracing/options/pause-on-trace
[root@localhost ~]# less -F /sys/kernel/tracing/trace
screen window 2
[root@localhost ~]# cat /sys/kernel/debug/tracing/tracing_on
0
[root@localhost ~]# echo hwlat > /sys/kernel/debug/tracing/current_tracer
[root@localhost ~]# echo 1 > /sys/kernel/debug/tracing/tracing_on
[root@localhost ~]# cat /sys/kernel/debug/tracing/tracing_on
0
[root@localhost ~]# echo 2 > /sys/kernel/debug/tracing/tracing_on
triggers warning in dmesg:
WARNING: CPU: 3 PID: 1403 at kernel/trace/trace_hwlat.c:371 hwlat_tracer_start+0xc9/0xd0
Link: https://lkml.kernel.org/r/bd4d3e70-400d-9c82-7b73-a2d695e86b58@virtuozzo.com
Cc: Ingo Molnar <mingo@redhat.com>
Cc: stable@vger.kernel.org
Fixes: 978defee11 ("tracing: Do a WARN_ON() if start_thread() in hwlat is called when thread exists")
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1d2bb5ad89 ]
When command interface is down, driver to reclaim all 4K page chucks that
were hold by the Firmeware. Fix a bug for 64K page size systems, where
driver repeatedly released only the first chunk of the page.
Define helper function to fill 4K chunks for a given Firmware pages.
Iterate over all unreleased Firmware pages and call the hepler per each.
Fixes: 5adff6a088 ("net/mlx5: Fix incorrect page count when in internal error")
Signed-off-by: Eran Ben Elisha <eranbe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d421e466c2 ]
STEs format for Connect-X5 and Connect-X6DX different. Currently, on
Connext-X6DX the SW steering would break at some point when building STEs
w/o giving a proper error message. Fix this by checking the STE format of
the current device when initializing domain: add mlx5_ifc definitions for
Connect-X6DX SW steering, read FW capability to get the current format
version, and check this version when domain is being created.
Fixes: 26d688e33f ("net/mlx5: DR, Add Steering entry (STE) utilities")
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 391119fb5c ]
The "skb" is freed by the transmit code in cxgb4_ofld_send() and we
shouldn't use it again. But in the current code, if we hit an error
later on in the function then the clean up code will call kfree_skb(skb)
and so it causes a double free.
Set the "skb" to NULL and that makes the kfree_skb() a no-op.
Fixes: d25f2f71f6 ("crypto: chtls - Program the TLS session Key")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/X8ilb6PtBRLWiSHp@mwanda
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6ee50c8e26 ]
The .x25_addr[] address comes from the user and is not necessarily
NUL terminated. This leads to a couple problems. The first problem is
that the strlen() in x25_bind() can read beyond the end of the buffer.
The second problem is more subtle and could result in memory corruption.
The call tree is:
x25_connect()
--> x25_write_internal()
--> x25_addr_aton()
The .x25_addr[] buffers are copied to the "addresses" buffer from
x25_write_internal() so it will lead to stack corruption.
Verify that the strings are NUL terminated and return -EINVAL if they
are not.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Fixes: a9288525d2 ("X25: Dont let x25_bind use addresses containing characters")
Reported-by: "kiyin(尹亮)" <kiyin@tencent.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Martin Schiller <ms@dev.tdt.de>
Link: https://lore.kernel.org/r/X8ZeAKm8FnFpN//B@mwanda
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 832ba59649 ]
syzkaller managed to crash the kernel using an NBMA ip6gre interface. I
could reproduce it creating an NBMA ip6gre interface and forwarding
traffic to it:
skbuff: skb_under_panic: text:ffffffff8250e927 len:148 put:44 head:ffff8c03c7a33
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:109!
Call Trace:
skb_push+0x10/0x10
ip6gre_header+0x47/0x1b0
neigh_connected_output+0xae/0xf0
ip6gre tunnel provides its own header_ops->create, and sets it
conditionally when initializing the tunnel in NBMA mode. When
header_ops->create is used, dev->hard_header_len should reflect the
length of the header created. Otherwise, when not used,
dev->needed_headroom should be used.
Fixes: eb95f52fc7 ("net: ipv6_gre: Fix GRO to work on IPv6 over GRE tap")
Cc: Maria Pasechnik <mariap@mellanox.com>
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Link: https://lore.kernel.org/r/20201130161911.464106-1-atenart@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2867e1eac6 ]
When adding support for propagating ECT(1) marking in IP headers it seems I
suffered from endianness-confusion in the checksum update calculation: In
fact the ECN field is in the *lower* bits of the first 16-bit word of the
IP header when calculating in network byte order. This means that the
addition performed to update the checksum field was wrong; let's fix that.
Fixes: b723748750 ("tunnel: Propagate ECT(1) when decapsulating as recommended by RFC6040")
Reported-by: Jonathan Morton <chromatix99@gmail.com>
Tested-by: Pete Heist <pete@heistp.net>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20201130183705.17540-1-toke@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ba246c1751 ]
TX completions received with an error return code are not
being processed properly. When an error code is seen, do not
proceed to the next completion before cleaning up the existing
entry's data structures.
Fixes: 032c5e8284 ("Driver for IBM System i/p VNIC protocol")
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b71ec95223 ]
Ensure that received Subordinate Command-Response Queue (SCRQ)
entries are properly read in order by the driver. These queues
are used in the ibmvnic device to process RX buffer and TX completion
descriptors. dma_rmb barriers have been added after checking for a
pending descriptor to ensure the correct descriptor entry is checked
and after reading the SCRQ descriptor to ensure the entire
descriptor is read before processing.
Fixes: 032c5e8284 ("Driver for IBM System i/p VNIC protocol")
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4d521943f7 ]
GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
These are simple defines so they could be used in DTS but they will not
have the same meaning:
1. GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE
2. GPIO_ACTIVE_LOW = 1 = IRQ_TYPE_EDGE_RISING
Correct the interrupt flags, assuming the author of the code wanted same
logical behavior behind the name "ACTIVE_xxx", this is:
ACTIVE_LOW => IRQ_TYPE_LEVEL_LOW
ACTIVE_HIGH => IRQ_TYPE_LEVEL_HIGH
Fixes: a1a8b4594f ("NFC: pn544: i2c: Add DTS Documentation")
Fixes: 6be88670fc ("NFC: nxp-nci_i2c: Add I2C support to NXP NCI driver")
Fixes: e3b3292215 ("dt-bindings: can: tcan4x5x: Update binding to use interrupt property")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for tcan4x5x.txt
Link: https://lore.kernel.org/r/20201026153620.89268-1-krzk@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1ebf179037 ]
When inet_rtm_getroute() was converted to use the RCU variants of
ip_route_input() and ip_route_output_key(), the TOS parameters
stopped being masked with IPTOS_RT_MASK before doing the route lookup.
As a result, "ip route get" can return a different route than what
would be used when sending real packets.
For example:
$ ip route add 192.0.2.11/32 dev eth0
$ ip route add unreachable 192.0.2.11/32 tos 2
$ ip route get 192.0.2.11 tos 2
RTNETLINK answers: No route to host
But, packets with TOS 2 (ECT(0) if interpreted as an ECN bit) would
actually be routed using the first route:
$ ping -c 1 -Q 2 192.0.2.11
PING 192.0.2.11 (192.0.2.11) 56(84) bytes of data.
64 bytes from 192.0.2.11: icmp_seq=1 ttl=64 time=0.173 ms
--- 192.0.2.11 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.173/0.173/0.173/0.000 ms
This patch re-applies IPTOS_RT_MASK in inet_rtm_getroute(), to
return results consistent with real route lookups.
Fixes: 3765d35ed8 ("net: ipv4: Convert inet_rtm_getroute to rcu versions of route lookup")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/b2d237d08317ca55926add9654a48409ac1b8f5b.1606412894.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 44f64f23ba ]
Netfilter changes PACKET_OTHERHOST to PACKET_HOST before invoking the
hooks as, while it's an expected value for a bridge, routing expects
PACKET_HOST. The change is undone later on after hook traversal. This
can be seen with pairs of functions updating skb>pkt_type and then
reverting it to its original value:
For hook NF_INET_PRE_ROUTING:
setup_pre_routing / br_nf_pre_routing_finish
For hook NF_INET_FORWARD:
br_nf_forward_ip / br_nf_forward_finish
But the third case where netfilter does this, for hook
NF_INET_POST_ROUTING, the packet type is changed in br_nf_post_routing
but never reverted. A comment says:
/* We assume any code from br_dev_queue_push_xmit onwards doesn't care
* about the value of skb->pkt_type. */
But when having a tunnel (say vxlan) attached to a bridge we have the
following call trace:
br_nf_pre_routing
br_nf_pre_routing_ipv6
br_nf_pre_routing_finish
br_nf_forward_ip
br_nf_forward_finish
br_nf_post_routing <- pkt_type is updated to PACKET_HOST
br_nf_dev_queue_xmit <- but not reverted to its original value
vxlan_xmit
vxlan_xmit_one
skb_tunnel_check_pmtu <- a check on pkt_type is performed
In this specific case, this creates issues such as when an ICMPv6 PTB
should be sent back. When CONFIG_BRIDGE_NETFILTER is enabled, the PTB
isn't sent (as skb_tunnel_check_pmtu checks if pkt_type is PACKET_HOST
and returns early).
If the comment is right and no one cares about the value of
skb->pkt_type after br_dev_queue_push_xmit (which isn't true), resetting
it to its original value should be safe.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Florian Westphal <fw@strlen.de>
Link: https://lore.kernel.org/r/20201123174902.622102-1-atenart@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 20c59ce010 ]
Registers 8-9 are used to store measurements of the kernel and its
command line (e.g., grub2 bootloader with tpm module enabled). IMA
should include them in the boot aggregate. Registers 8-9 should be
only included in non-SHA1 digests to avoid ambiguity.
Signed-off-by: Maurizio Drocco <maurizio.drocco@ibm.com>
Reviewed-by: Bruno Meneguele <bmeneg@redhat.com>
Tested-by: Bruno Meneguele <bmeneg@redhat.com> (TPM 1.2, TPM 2.0)
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 673b41e04a upstream.
There's a semantic conflict in the Octeon staging network driver, which
used the skb_reset_tc() function to reset skb state when re-using an
skb. But that inline helper function was removed in mainline by commit
2c64605b59 ("net: Fix CONFIG_NET_CLS_ACT=n and
CONFIG_NFT_FWD_NETDEV={y, m} build").
Fix it by using skb_reset_redirect() instead. Also move it out of the
This code path only ends up triggering if REUSE_SKBUFFS_WITHOUT_FREE is
enabled, which in turn only happens if you don't have CONFIG_NETFILTER
configured. Which was how this wasn't caught by the usual allmodconfig
builds.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f33d9e2b48 ]
Starting with iOS 14 released in September 2020, connectivity using the
personal hotspot USB tethering function of iOS devices is broken.
Communication between the host and the device (for example ICMP traffic
or DNS resolution using the DNS service running in the device itself)
works fine, but communication to endpoints further away doesn't work.
Investigation on the matter shows that no UDP and ICMP traffic from the
tethered host is reaching the Internet at all. For TCP traffic there are
exchanges between tethered host and server but packets are modified in
transit leading to impossible communication.
After some trials Matti Vuorela discovered that reducing the URB buffer
size by two bytes restored the previous behavior. While a better
solution might exist to fix the issue, since the protocol is not
publicly documented and considering the small size of the fix, let's do
that.
Tested-by: Matti Vuorela <matti.vuorela@bitfactor.fi>
Signed-off-by: Yves-Alexis Perez <corsac@corsac.net>
Link: https://lore.kernel.org/linux-usb/CAAn0qaXmysJ9vx3ZEMkViv_B19ju-_ExN8Yn_uSefxpjS6g4Lw@mail.gmail.com/
Link: https://github.com/libimobiledevice/libimobiledevice/issues/1038
Link: https://lore.kernel.org/r/20201119172439.94988-1-corsac@corsac.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 55472017a4 ]
When setting congestion control via a BPF program it is seen that the
SYN/ACK for packets within a given flow will not include the ECT0 flag. A
bit of simple printk debugging shows that when this is configured without
BPF we will see the value INET_ECN_xmit value initialized in
tcp_assign_congestion_control however when we configure this via BPF the
socket is in the closed state and as such it isn't configured, and I do not
see it being initialized when we transition the socket into the listen
state. The result of this is that the ECT0 bit is configured based on
whatever the default state is for the socket.
Any easy way to reproduce this is to monitor the following with tcpdump:
tools/testing/selftests/bpf/test_progs -t bpf_tcp_ca
Without this patch the SYN/ACK will follow whatever the default is. If dctcp
all SYN/ACK packets will have the ECT0 bit set, and if it is not then ECT0
will be cleared on all SYN/ACK packets. With this patch applied the SYN/ACK
bit matches the value seen on the other packets in the given stream.
Fixes: 91b5b21c7c ("bpf: Add support for changing congestion control")
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 985f733742 ]
When setting sk_err, set it to ee_errno, not ee_origin.
Commit f5f99309fa ("sock: do not set sk_err in
sock_dequeue_err_skb") disabled updating sk_err on errq dequeue,
which is correct for most error types (origins):
- sk->sk_err = err;
Commit 38b257938a ("sock: reset sk_err when the error queue is
empty") reenabled the behavior for IMCP origins, which do require it:
+ if (icmp_next)
+ sk->sk_err = SKB_EXT_ERR(skb_next)->ee.ee_origin;
But read from ee_errno.
Fixes: 38b257938a ("sock: reset sk_err when the error queue is empty")
Reported-by: Ayush Ranjan <ayushranjan@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Link: https://lore.kernel.org/r/20201126151220.2819322-1-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 025cc2fb6a ]
tls_device_offload_cleanup_rx doesn't clear tls_ctx->netdev after
calling tls_dev_del if TLX TX offload is also enabled. Clearing
tls_ctx->netdev gets postponed until tls_device_gc_task. It leaves a
time frame when tls_device_down may get called and call tls_dev_del for
RX one extra time, confusing the driver, which may lead to a crash.
This patch corrects this racy behavior by adding a flag to prevent
tls_device_down from calling tls_dev_del the second time.
Fixes: e8f6979981 ("net/tls: Add generic NIC offload infrastructure")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20201125221810.69870-1-saeedm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 20ffc7adf5 ]
In case when tcp socket received FIN after some data and the
parser haven't started before reading data caller will receive
an empty buffer. This behavior differs from plain TCP socket and
leads to special treating in user-space.
The flow that triggers the race is simple. Server sends small
amount of data right after the connection is configured to use TLS
and closes the connection. In this case receiver sees TLS Handshake
data, configures TLS socket right after Change Cipher Spec record.
While the configuration is in process, TCP socket receives small
Application Data record, Encrypted Alert record and FIN packet. So
the TCP socket changes sk_shutdown to RCV_SHUTDOWN and sk_flag with
SK_DONE bit set. The received data is not parsed upon arrival and is
never sent to user-space.
Patch unpauses parser directly if we have unparsed data in tcp
receive queue.
Fixes: fcf4793e27 ("tls: check RCV_SHUTDOWN in tls_wait_data")
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Link: https://lore.kernel.org/r/1605801588-12236-1-git-send-email-vfedorenko@novek.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c5dab0941f ]
Child sockets erroneously inherit their parent's sk_type (ie. SOCK_*),
instead of the PF_IUCV protocol that the parent was created with in
iucv_sock_create().
We're currently not using sk->sk_protocol ourselves, so this shouldn't
have much impact (except eg. getting the output in skb_dump() right).
Fixes: eac3731bd0 ("[S390]: Add AF_IUCV socket support")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Link: https://lore.kernel.org/r/20201120100657.34407-1-jwi@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b187c9b417 ]
A netdevice of a devlink port can be moved to different net namespace
than its parent devlink instance.
This scenario occurs when devlink reload is not used.
When netdevice is undergoing migration to net namespace, its ifindex
and name may change.
In such use case, devlink port query may read stale netdev attributes.
Fix it by reading them under rtnl lock.
Fixes: bfcd3a4661 ("Introduce devlink infrastructure")
Signed-off-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for the PCF85063 and PCF85063A RTC devices to the
i2c-rtc overlay.
Also enable the device to be used on i2c0 (i2c_vc) on GPIOs 0&1 (use
parameter "i2c0") and GPIOs 44 & 45 (use parameter "i2c_csi_dsi").
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Commit 65e08c4650 failed to clear the
clock state when the device stopped streaming. Fix this, as it might
again cause the same problems when doing an unprepare.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
clk_disable_unprepare() is called unconditionally in stop_streaming().
This is incorrect in the cases where start_streaming() fails, and
unprepares all clocks as part of the failure cleanup. To avoid this,
ensure that clk_disable_unprepare() is only called in stop_streaming()
if the clocks are in a prepared state.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
On a failure in start_streaming(), the error code would not propagate to
the calling function on all conditions. This would cause the userland
caller to not know of the failure.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
To comply with the intended usage of the V4L2 selection target when
used to retrieve a sensor image properties, adjust the rectangles
returned by the imx219 driver.
The top/left crop coordinates of the TGT_CROP rectangle were set to
(0, 0) instead of (8, 8) which is the offset from the larger physical
pixel array rectangle. This was also a mismatch with the default values
crop rectangle value, so this is corrected. Found with v4l2-compliance.
While at it, add V4L2_SEL_TGT_CROP_BOUNDS support: CROP_DEFAULT and
CROP_BOUNDS have the same size as the non-active pixels are not readable
using the selection API. Found with v4l2-compliance.
Fixes: e6d4ef7d58 ("media: i2c: imx219: Implement get_selection")
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[reword commit message, use macros for pixel offsets]
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
commit 2ef81057d8 upstream.
Skylake driver does the controller init operation twice:
- first during probe (only to stop it just before scheduling probe_work)
- and during said probe_work where the actual correct sequence is
executed
To properly complete boot sequence when iDisp codec is present, bus
initialization has to be called only after _i915_init() finishes.
With additional _reset_list preceding _i915_init(), iDisp codec never
gets the chance to enumerate on the link. Remove the superfluous
initialization to address the issue.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200305145314.32579-2-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org> # 5.4.x
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 184eead057 upstream
Commit 3e4f8e21c4 ("USB: core: fix check for duplicate endpoints")
aimed to make the USB stack more reliable by detecting and skipping
over endpoints that are duplicated between interfaces. This caused a
regression for a Hercules audio card (reported as Bugzilla #208357),
which contains such non-compliant duplications. Although the
duplications are harmless, skipping the valid endpoints prevented the
device from working.
This patch fixes the regression by adding ENDPOINT_IGNORE quirks for
the Hercules card, telling the kernel to ignore the invalid duplicate
endpoints and thereby allowing the valid endpoints to be used as
intended.
Fixes: 3e4f8e21c4 ("USB: core: fix check for duplicate endpoints")
CC: <stable@vger.kernel.org>
Reported-by: Alexander Chalikiopoulos <bugzilla.kernel.org@mrtoasted.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20201119170040.GA576844@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[sudip: use usb_endpoint_blacklist and USB_QUIRK_ENDPOINT_BLACKLIST]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7589992469 upstream.
On resource group creation via a mkdir an extra kernfs_node reference is
obtained by kernfs_get() to ensure that the rdtgroup structure remains
accessible for the rdtgroup_kn_unlock() calls where it is removed on
deletion. Currently the extra kernfs_node reference count is only
dropped by kernfs_put() in rdtgroup_kn_unlock() while the rdtgroup
structure is removed in a few other locations that lack the matching
reference drop.
In call paths of rmdir and umount, when a control group is removed,
kernfs_remove() is called to remove the whole kernfs nodes tree of the
control group (including the kernfs nodes trees of all child monitoring
groups), and then rdtgroup structure is freed by kfree(). The rdtgroup
structures of all child monitoring groups under the control group are
freed by kfree() in free_all_child_rdtgrp().
Before calling kfree() to free the rdtgroup structures, the kernfs node
of the control group itself as well as the kernfs nodes of all child
monitoring groups still take the extra references which will never be
dropped to 0 and the kernfs nodes will never be freed. It leads to
reference count leak and kernfs_node_cache memory leak.
For example, reference count leak is observed in these two cases:
(1) mount -t resctrl resctrl /sys/fs/resctrl
mkdir /sys/fs/resctrl/c1
mkdir /sys/fs/resctrl/c1/mon_groups/m1
umount /sys/fs/resctrl
(2) mkdir /sys/fs/resctrl/c1
mkdir /sys/fs/resctrl/c1/mon_groups/m1
rmdir /sys/fs/resctrl/c1
The same reference count leak issue also exists in the error exit paths
of mkdir in mkdir_rdt_prepare() and rdtgroup_mkdir_ctrl_mon().
Fix this issue by following changes to make sure the extra kernfs_node
reference on rdtgroup is dropped before freeing the rdtgroup structure.
(1) Introduce rdtgroup removal helper rdtgroup_remove() to wrap up
kernfs_put() and kfree().
(2) Call rdtgroup_remove() in rdtgroup removal path where the rdtgroup
structure is about to be freed by kfree().
(3) Call rdtgroup_remove() or kernfs_put() as appropriate in the error
exit paths of mkdir where an extra reference is taken by kernfs_get().
Fixes: f3cbeacaa0 ("x86/intel_rdt/cqm: Add rmdir support")
Fixes: e02737d5b8 ("x86/intel_rdt: Add tasks files")
Fixes: 60cf5e101f ("x86/intel_rdt: Add mkdir to resctrl file system")
Reported-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Xiaochen Shen <xiaochen.shen@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1604085088-31707-1-git-send-email-xiaochen.shen@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fd8d9db355 upstream.
Willem reported growing of kernfs_node_cache entries in slabtop when
repeatedly creating and removing resctrl subdirectories as well as when
repeatedly mounting and unmounting the resctrl filesystem.
On resource group (control as well as monitoring) creation via a mkdir
an extra kernfs_node reference is obtained to ensure that the rdtgroup
structure remains accessible for the rdtgroup_kn_unlock() calls where it
is removed on deletion. The kernfs_node reference count is dropped by
kernfs_put() in rdtgroup_kn_unlock().
With the above explaining the need for one kernfs_get()/kernfs_put()
pair in resctrl there are more places where a kernfs_node reference is
obtained without a corresponding release. The excessive amount of
reference count on kernfs nodes will never be dropped to 0 and the
kernfs nodes will never be freed in the call paths of rmdir and umount.
It leads to reference count leak and kernfs_node_cache memory leak.
Remove the superfluous kernfs_get() calls and expand the existing
comments surrounding the remaining kernfs_get()/kernfs_put() pair that
remains in use.
Superfluous kernfs_get() calls are removed from two areas:
(1) In call paths of mount and mkdir, when kernfs nodes for "info",
"mon_groups" and "mon_data" directories and sub-directories are
created, the reference count of newly created kernfs node is set to 1.
But after kernfs_create_dir() returns, superfluous kernfs_get() are
called to take an additional reference.
(2) kernfs_get() calls in rmdir call paths.
Fixes: 17eafd0762 ("x86/intel_rdt: Split resource group removal in two")
Fixes: 4af4a88e0c ("x86/intel_rdt/cqm: Add mount,umount support")
Fixes: f3cbeacaa0 ("x86/intel_rdt/cqm: Add rmdir support")
Fixes: d89b737901 ("x86/intel_rdt/cqm: Add mon_data")
Fixes: c7d9aac613 ("x86/intel_rdt/cqm: Add mkdir support for RDT monitoring")
Fixes: 5dc1d5c6ba ("x86/intel_rdt: Simplify info and base file lists")
Fixes: 60cf5e101f ("x86/intel_rdt: Add mkdir to resctrl file system")
Fixes: 4e978d06de ("x86/intel_rdt: Add "info" files to resctrl file system")
Reported-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Xiaochen Shen <xiaochen.shen@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Willem de Bruijn <willemb@google.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1604085053-31639-1-git-send-email-xiaochen.shen@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 33fc379df7 upstream.
When spectre_v2_user={seccomp,prctl},ibpb is specified on the command
line, IBPB is force-enabled and STIPB is conditionally-enabled (or not
available).
However, since
21998a3515 ("x86/speculation: Avoid force-disabling IBPB based on STIBP and enhanced IBRS.")
the spectre_v2_user_ibpb variable is set to SPECTRE_V2_USER_{PRCTL,SECCOMP}
instead of SPECTRE_V2_USER_STRICT, which is the actual behaviour.
Because the issuing of IBPB relies on the switch_mm_*_ibpb static
branches, the mitigations behave as expected.
Since
1978b3a53a ("x86/speculation: Allow IBPB to be conditionally enabled on CPUs with always-on STIBP")
this discrepency caused the misreporting of IB speculation via prctl().
On CPUs with STIBP always-on and spectre_v2_user=seccomp,ibpb,
prctl(PR_GET_SPECULATION_CTRL) would return PR_SPEC_PRCTL |
PR_SPEC_ENABLE instead of PR_SPEC_DISABLE since both IBPB and STIPB are
always on. It also allowed prctl(PR_SET_SPECULATION_CTRL) to set the IB
speculation mode, even though the flag is ignored.
Similarly, for CPUs without SMT, prctl(PR_GET_SPECULATION_CTRL) should
also return PR_SPEC_DISABLE since IBPB is always on and STIBP is not
available.
[ bp: Massage commit message. ]
Fixes: 21998a3515 ("x86/speculation: Avoid force-disabling IBPB based on STIBP and enhanced IBRS.")
Fixes: 1978b3a53a ("x86/speculation: Allow IBPB to be conditionally enabled on CPUs with always-on STIBP")
Signed-off-by: Anand K Mistry <amistry@google.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20201110123349.1.Id0cbf996d2151f4c143c90f9028651a5b49a5908@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 25bc65d8dd upstream.
Currently, if mce_end() fails, no_way_out - the variable denoting
whether the machine can recover from this MCE - is determined by whether
the worst severity that was found across the MCA banks associated with
the current CPU, is of panic severity.
However, at this point no_way_out could have been already set by
mca_start() after looking at all severities of all CPUs that entered the
MCE handler. If mce_end() fails, check first if no_way_out is already
set and, if so, stick to it, otherwise use the local worst value.
[ bp: Massage. ]
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20201127161819.3106432-2-gabriele.paoloni@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9ca5751836 upstream.
Add a USB_QUIRK_DISCONNECT_SUSPEND quirk for the Lenovo TIO built-in
usb-audio. when A630Z going into S3,the system immediately wakeup 7-8
seconds later by usb-audio disconnect interrupt to avoids the issue.
eg dmesg:
....
[ 626.974091 ] usb 7-1.1: USB disconnect, device number 3
....
....
[ 1774.486691] usb 7-1.1: new full-speed USB device number 5 using xhci_hcd
[ 1774.947742] usb 7-1.1: New USB device found, idVendor=17ef, idProduct=a012, bcdDevice= 0.55
[ 1774.956588] usb 7-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1774.964339] usb 7-1.1: Product: Thinkcentre TIO24Gen3 for USB-audio
[ 1774.970999] usb 7-1.1: Manufacturer: Lenovo
[ 1774.975447] usb 7-1.1: SerialNumber: 000000000000
[ 1775.048590] usb 7-1.1: 2:1: cannot get freq at ep 0x1
.......
Seeking a better fix, we've tried a lot of things, including:
- Check that the device's power/wakeup is disabled
- Check that remote wakeup is off at the USB level
- All the quirks in drivers/usb/core/quirks.c
e.g. USB_QUIRK_RESET_RESUME,
USB_QUIRK_RESET,
USB_QUIRK_IGNORE_REMOTE_WAKEUP,
USB_QUIRK_NO_LPM.
but none of that makes any difference.
There are no errors in the logs showing any suspend/resume-related issues.
When the system wakes up due to the modem, log-wise it appears to be a
normal resume.
Introduce a quirk to disable the port during suspend when the modem is
detected.
Signed-off-by: penghao <penghao@uniontech.com>
Link: https://lore.kernel.org/r/20201118123039.11696-1-penghao@uniontech.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f3bc432aa8 upstream.
Commit 2f964780c0 ("USB: core: replace %p with %pK") used the %pK
format specifier for a bunch of __user pointers. But as the 'K' in
the specifier indicates, it is meant for kernel pointers. The reason
for the %pK specifier is to avoid leaks of kernel addresses, but when
the pointer is to an address in userspace the security implications
are minimal. In particular, no kernel information is leaked.
This patch changes the __user %pK specifiers (used in a bunch of
debugging output lines) to %px, which will always print the actual
address with no mangling. (Notably, there is no printk format
specifier particularly intended for __user pointers.)
Fixes: 2f964780c0 ("USB: core: replace %p with %pK")
CC: Vamsi Krishna Samavedam <vskrishn@codeaurora.org>
CC: <stable@vger.kernel.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20201119170228.GB576844@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d853b34069 upstream.
Clang warns:
drivers/spi/spi-bcm2835aux.c:532:50: warning: variable 'err' is
uninitialized when used here [-Wuninitialized]
dev_err(&pdev->dev, "could not get clk: %d\n", err);
^~~
./include/linux/dev_printk.h:112:32: note: expanded from macro 'dev_err'
_dev_err(dev, dev_fmt(fmt), ##__VA_ARGS__)
^~~~~~~~~~~
drivers/spi/spi-bcm2835aux.c:495:9: note: initialize the variable 'err'
to silence this warning
int err;
^
= 0
1 warning generated.
Restore the assignment so that the error value can be used in the
dev_err statement and there is no uninitialized memory being leaked.
Fixes: e13ee6cc47 ("spi: bcm2835aux: Fix use-after-free on unbind")
Link: https://github.com/ClangBuiltLinux/linux/issues/1199
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Link: https://lore.kernel.org/r/20201113180701.455541-1-natechancellor@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c0ee1d5ae8 ]
Currently perf stat shows some metrics (like IPC) for defined events.
But when no aggregation mode is used (-A option), it shows incorrect
values since it used a value from a different cpu.
Before:
$ perf stat -aA -e cycles,instructions sleep 1
Performance counter stats for 'system wide':
CPU0 116,057,380 cycles
CPU1 86,084,722 cycles
CPU2 99,423,125 cycles
CPU3 98,272,994 cycles
CPU0 53,369,217 instructions # 0.46 insn per cycle
CPU1 33,378,058 instructions # 0.29 insn per cycle
CPU2 58,150,086 instructions # 0.50 insn per cycle
CPU3 40,029,703 instructions # 0.34 insn per cycle
1.001816971 seconds time elapsed
So the IPC for CPU1 should be 0.38 (= 33,378,058 / 86,084,722)
but it was 0.29 (= 33,378,058 / 116,057,380) and so on.
After:
$ perf stat -aA -e cycles,instructions sleep 1
Performance counter stats for 'system wide':
CPU0 109,621,384 cycles
CPU1 159,026,454 cycles
CPU2 99,460,366 cycles
CPU3 124,144,142 cycles
CPU0 44,396,706 instructions # 0.41 insn per cycle
CPU1 120,195,425 instructions # 0.76 insn per cycle
CPU2 44,763,978 instructions # 0.45 insn per cycle
CPU3 69,049,079 instructions # 0.56 insn per cycle
1.001910444 seconds time elapsed
Fixes: 44d49a6002 ("perf stat: Support metrics in --per-core/socket mode")
Reported-by: Sam Xi <xyzsam@google.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lore.kernel.org/lkml/20201127041404.390276-1-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 865f5b671b ]
The threaded IRQ handler is used for the tcan4x5x driver only. The IRQ pin of
the tcan4x5x controller is active low, so better not use IRQF_TRIGGER_FALLING
when requesting the IRQ. As this can result in missing interrupts.
Further, if the device tree specified the interrupt as "IRQ_TYPE_LEVEL_LOW",
unloading and reloading of the driver results in the following error during
ifup:
| irq: type mismatch, failed to map hwirq-31 for gpio@20a8000!
| tcan4x5x spi1.1: m_can device registered (irq=0, version=32)
| tcan4x5x spi1.1 can2: TCAN4X5X successfully initialized.
| tcan4x5x spi1.1 can2: failed to request interrupt
This patch fixes the problem by removing the IRQF_TRIGGER_FALLING from the
request_threaded_irq().
Fixes: f524f829b7 ("can: m_can: Create a m_can platform framework")
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Sriram Dash <sriram.dash@samsung.com>
Cc: Pankaj Sharma <pankj.sharma@samsung.com>
Link: https://lore.kernel.org/r/20201127093548.509253-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ba1cb39fc ]
The firmware on the original USB2CAN by Geschwister Schneider Technologie
Entwicklungs- und Vertriebs UG exchanges all data between the host and the
device in host byte order. This is done with the struct
gs_host_config::byte_order member, which is sent first to indicate the desired
byte order.
The widely used open source firmware candleLight doesn't support this feature
and exchanges the data in little endian byte order. This breaks if a device
with candleLight firmware is used on big endianess systems.
To fix this problem, all u32 (but not the struct gs_host_frame::echo_id, which
is a transparent cookie) are converted to __le32.
Cc: Maximilian Schneider <max@schneidersoft.net>
Cc: Hubert Denkmair <hubert@denkmair.de>
Reported-by: Michael Rausch <mr@netadair.de>
Link: https://lore.kernel.org/r/b58aace7-61f3-6df7-c6df-69fee2c66906@netadair.de
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Fixes: d08e973a77 ("can: gs_usb: Added support for the GS_USB CAN devices")
Link: https://lore.kernel.org/r/20201120103818.3386964-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 36a237526c ]
CONFIG_EFI_EARLYCON defaults to yes, and thus is enabled on systems that
do not support EFI, or do not have EFI support enabled, but do satisfy
the symbol's other dependencies.
While drivers/firmware/efi/ won't be entered during the build phase if
CONFIG_EFI=n, and drivers/firmware/efi/earlycon.c itself thus won't be
built, enabling EFI_EARLYCON does force-enable CONFIG_FONT_SUPPORT and
CONFIG_ARCH_USE_MEMREMAP_PROT, and CONFIG_FONT_8x16, which is
undesirable.
Fix this by making CONFIG_EFI_EARLYCON depend on CONFIG_EFI.
This reduces kernel size on headless systems by more than 4 KiB.
Fixes: 69c1f396f2 ("efi/x86: Convert x86 EFI earlyprintk into generic earlycon implementation")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20201124191646.3559757-1-geert@linux-m68k.org
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff04f3b6f2 ]
The memory leak addressed by commit fe5186cf12 is a false positive:
all allocations are recorded in a linked list, and freed when the
filesystem is unmounted. This leads to double frees, and as reported
by David, leads to crashes if SLUB is configured to self destruct when
double frees occur.
So drop the redundant kfree() again, and instead, mark the offending
pointer variable so the allocation is ignored by kmemleak.
Cc: Vamshi K Sthambamkadi <vamshi.k.sthambamkadi@gmail.com>
Fixes: fe5186cf12 ("efivarfs: fix memory leak in efivarfs_create()")
Reported-by: David Laight <David.Laight@aculab.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1741e18737 ]
The AON HSP node's "reg" property size 0xa0000 will overlap with other
resources. This patch fixes that wrong value with correct size 0x90000.
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Dipen Patel <dipenp@nvidia.com>
Fixes: a38570c22e ("arm64: tegra: Add nodes for TCU on Tegra194")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 853735e404 ]
Only in smp systems the cache policy is setup as write alloc, in
single cpu systems the cache policy is set as writeback and it is
normal memory, so, it should pass the is_normal_memory check in the
share memory registration.
Add the right condition to make it work in no smp systems.
Fixes: cdbcf83d29 ("tee: optee: check type of registered shared memory")
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09323b3bca ]
The ENA driver uses the readless mechanism, which uses DMA, to find
out what the DMA mask is supposed to be.
If DMA is used without setting the dma_mask first, it causes the
Intel IOMMU driver to think that ENA is a 32-bit device and therefore
disables IOMMU passthrough permanently.
This patch sets the dma_mask to be ENA_MAX_PHYS_ADDR_SIZE_BITS=48
before readless initialization in
ena_device_init()->ena_com_mmio_reg_read_request_init(),
which is large enough to workaround the intel_iommu issue.
DMA mask is set again to the correct value after it's received from the
device after readless is initialized.
The patch also changes the driver to use dma_set_mask_and_coherent()
function instead of the two pci_set_dma_mask() and
pci_set_consistent_dma_mask() ones. Both methods achieve the same
effect.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Mike Cui <mikecui@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d8f0a86795 ]
GPIOs - as returned by of_get_named_gpio() and used by the gpiolib - are
signed integers, where negative number indicates error. The return
value of of_get_named_gpio() should not be assigned to an unsigned int
because in case of !CONFIG_GPIOLIB such number would be a valid GPIO.
Fixes: c04c674fad ("nfc: s3fwrn5: Add driver for Samsung S3FWRN5 NFC Chip")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201123162351.209100-1-krzk@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2980cbd4dc ]
Prevent VFs from resetting when PF driver is being unloaded:
- introduce new pf state: __I40E_VF_RESETS_DISABLED;
- check if pf state has __I40E_VF_RESETS_DISABLED state set,
if so, disable any further VFLR event notifications;
- when i40e_remove (rmmod i40e) is called, disable any resets on
the VFs;
Previously if there were bare-metal VFs passing traffic and PF
driver was removed, there was a possibility of VFs triggering a Tx
timeout right before iavf_remove. This was causing iavf_close to
not be called because there is a check in the beginning of iavf_remove
that bails out early if adapter->state < IAVF_DOWN_PENDING. This
makes it so some resources do not get cleaned up.
Fixes: 6a9ddb36ee ("i40e: disable IOV before freeing resources")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20201120180640.3654474-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6b79dd530 ]
Using DECLARE_STATIC_KEY_FALSE needs linux/jump_table.h.
Otherwise the build fails with eg:
arch/powerpc/include/asm/book3s/64/kup-radix.h:66:1: warning: data definition has no type or storage class
66 | DECLARE_STATIC_KEY_FALSE(uaccess_flush_key);
Fixes: 9a32a7e78b ("powerpc/64s: flush L1D after user accesses")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
[mpe: Massage change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201123184016.693fe464@canb.auug.org.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 98025bce3a ]
Commit 61d3e1d9bc ("ibmvnic: Remove netdev notify for failover resets")
excluded the failover case for notify call because it said
netdev_notify_peers() can cause network traffic to stall or halt.
Current testing does not show network traffic stall
or halt because of the notify call for failover event.
netdev_notify_peers may be used when a device wants to inform the
rest of the network about some sort of a reconfiguration
such as failover or migration.
It is unnecessary to call that in other events like
FATAL, NON_FATAL, CHANGE_PARAM, and TIMEOUT resets
since in those scenarios the hardware does not change.
If the driver must do a hard reset, it is necessary to notify peers.
Fixes: 61d3e1d9bc ("ibmvnic: Remove netdev notify for failover resets")
Suggested-by: Brian King <brking@linux.vnet.ibm.com>
Suggested-by: Pradeep Satyanarayana <pradeeps@linux.vnet.ibm.com>
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ed10e16e5 ]
When qeth_iqd_tx_complete() detects that a TX buffer requires additional
async completion via QAOB, it might fail to replace the queue entry's
metadata (and ends up triggering recovery).
Assume now that the device gets torn down, overruling the recovery.
If the QAOB notification then arrives before the tear down has
sufficiently progressed, the buffer state is changed to
QETH_QDIO_BUF_HANDLED_DELAYED by qeth_qdio_handle_aob().
The tear down code calls qeth_drain_output_queue(), where
qeth_cleanup_handled_pending() will then attempt to replace such a
buffer _again_. If it succeeds this time, the buffer ends up dangling in
its replacement's ->next_pending list ... where it will never be freed,
since there's no further call to qeth_cleanup_handled_pending().
But the second attempt isn't actually needed, we can simply leave the
buffer on the queue and re-use it after a potential recovery has
completed. The qeth_clear_output_buffer() in qeth_drain_output_queue()
will ensure that it's in a clean state again.
Fixes: 72861ae792 ("qeth: recovery through asynchronous delivery")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8908f36d20 ]
The two expected notification sequences are
1. TX_NOTIFY_PENDING with a subsequent TX_NOTIFY_DELAYED_*, when
our TX completion code first observed the pending TX and the QAOB
then completes at a later time; or
2. TX_NOTIFY_OK, when qeth_qdio_handle_aob() picked up the QAOB
completion before our TX completion code even noticed that the TX
was pending.
But as qeth_iqd_tx_complete() and qeth_qdio_handle_aob() can run
concurrently, we may end up with a race that results in a sequence of
TX_NOTIFY_DELAYED_* followed by TX_NOTIFY_PENDING. Which would confuse
the af_iucv code in its tracking of pending transmits.
Rework the notification code, so that qeth_qdio_handle_aob() defers its
notification if the TX completion code is still active.
Fixes: b333293058 ("qeth: add support for af_iucv HiperSockets transport")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 34c7f50f7d ]
Calling into socket code is ugly already, at least check whether we are
dealing with the expected sk_family. Only looking at skb->protocol is
bound to cause troubles (consider eg. af_packet).
Fixes: b333293058 ("qeth: add support for af_iucv HiperSockets transport")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f1251a48c ]
x86 Hyper-V used to essentially always overwrite the effective cache type
of guest memory accesses to WB. This was problematic in cases where there
is a physical device assigned to the VM, since that often requires that
the VM should have control over cache types. Thus, on newer Hyper-V since
2018, Hyper-V always honors the VM's cache type, but unexpectedly Linux VM
users start to complain that Linux VM's VRAM becomes very slow, and it
turns out that Linux VM should not map the VRAM uncacheable by ioremap().
Fix this slowness issue by using ioremap_cache().
On ARM64, ioremap_cache() is also required as the host also maps the VRAM
cacheable, otherwise VM Connect can't display properly with ioremap() or
ioremap_wc().
With this change, the VRAM on new Hyper-V is as fast as regular RAM, so
it's no longer necessary to use the hacks we added to mitigate the
slowness, i.e. we no longer need to allocate physical memory and use
it to back up the VRAM in Generation-1 VM, and we also no longer need to
allocate physical memory to back up the framebuffer in a Generation-2 VM
and copy the framebuffer to the real VRAM. A further big change will
address these for v5.11.
Fixes: 68a2d20b79 ("drivers/video: add Hyper-V Synthetic Video Frame Buffer Driver")
Tested-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Link: https://lore.kernel.org/r/20201118000305.24797-1-decui@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e92643db51 ]
If UFS host device is in runtime-suspended state while UFS shutdown
callback is invoked, UFS device shall be resumed for register
accesses. Currently only UFS local runtime resume function will be invoked
to wake up the host. This is not enough because if someone triggers
runtime resume from block layer, then race may happen between shutdown and
runtime resume flow, and finally lead to unlocked register access.
To fix this, in ufshcd_shutdown(), use pm_runtime_get_sync() instead of
resuming UFS device by ufshcd_runtime_resume() "internally" to let runtime
PM framework manage the whole resume flow.
Link: https://lore.kernel.org/r/20201119062916.12931-1-stanley.chu@mediatek.com
Fixes: 57d104c153 ("ufs: add UFS power management support")
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cef3970381 ]
Stefan Agner reported a bug when using zsram on 32-bit Arm machines
with RAM above the 4GB address boundary:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = a27bd01c
[00000000] *pgd=236a0003, *pmd=1ffa64003
Internal error: Oops: 207 [#1] SMP ARM
Modules linked in: mdio_bcm_unimac(+) brcmfmac cfg80211 brcmutil raspberrypi_hwmon hci_uart crc32_arm_ce bcm2711_thermal phy_generic genet
CPU: 0 PID: 123 Comm: mkfs.ext4 Not tainted 5.9.6 #1
Hardware name: BCM2711
PC is at zs_map_object+0x94/0x338
LR is at zram_bvec_rw.constprop.0+0x330/0xa64
pc : [<c0602b38>] lr : [<c0bda6a0>] psr: 60000013
sp : e376bbe0 ip : 00000000 fp : c1e2921c
r10: 00000002 r9 : c1dda730 r8 : 00000000
r7 : e8ff7a00 r6 : 00000000 r5 : 02f9ffa0 r4 : e3710000
r3 : 000fdffe r2 : c1e0ce80 r1 : ebf979a0 r0 : 00000000
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 30c5383d Table: 235c2a80 DAC: fffffffd
Process mkfs.ext4 (pid: 123, stack limit = 0x495a22e6)
Stack: (0xe376bbe0 to 0xe376c000)
As it turns out, zsram needs to know the maximum memory size, which
is defined in MAX_PHYSMEM_BITS when CONFIG_SPARSEMEM is set, or in
MAX_POSSIBLE_PHYSMEM_BITS on the x86 architecture.
The same problem will be hit on all 32-bit architectures that have a
physical address space larger than 4GB and happen to not enable sparsemem
and include asm/sparsemem.h from asm/pgtable.h.
After the initial discussion, I suggested just always defining
MAX_POSSIBLE_PHYSMEM_BITS whenever CONFIG_PHYS_ADDR_T_64BIT is
set, or provoking a build error otherwise. This addresses all
configurations that can currently have this runtime bug, but
leaves all other configurations unchanged.
I looked up the possible number of bits in source code and
datasheets, here is what I found:
- on ARC, CONFIG_ARC_HAS_PAE40 controls whether 32 or 40 bits are used
- on ARM, CONFIG_LPAE enables 40 bit addressing, without it we never
support more than 32 bits, even though supersections in theory allow
up to 40 bits as well.
- on MIPS, some MIPS32r1 or later chips support 36 bits, and MIPS32r5
XPA supports up to 60 bits in theory, but 40 bits are more than
anyone will ever ship
- On PowerPC, there are three different implementations of 36 bit
addressing, but 32-bit is used without CONFIG_PTE_64BIT
- On RISC-V, the normal page table format can support 34 bit
addressing. There is no highmem support on RISC-V, so anything
above 2GB is unused, but it might be useful to eventually support
CONFIG_ZRAM for high pages.
Fixes: 61989a80fb ("staging: zsmalloc: zsmalloc memory allocation library")
Fixes: 02390b87a9 ("mm/zsmalloc: Prepare to variable MAX_PHYSMEM_BITS")
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Tested-by: Stefan Agner <stefan@agner.ch>
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Link: https://lore.kernel.org/linux-mm/bdfa44bf1c570b05d6c70898e2bbb0acf234ecdf.1604762181.git.stefan@agner.ch/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 14a2e551fa ]
If THIS_MODULE is not set, the module would be removed while debugfs is
being used.
It eventually makes kernel panic.
Fixes: c6c8fea297 ("net: Add batman-adv meshing protocol")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 294a3317be ]
Based on more testing, commit 8ca5ee624b4c ("ARM: OMAP2+: Restore MPU
power domain if cpu_cluster_pm_enter() fails") is a poor fix for handling
cpu_cluster_pm_enter() returned errors.
We should not override the cpuidle states with a hardcoded PWRDM_POWER_ON
value. Instead, we should use a configured idle state that does not cause
the context to be lost. Otherwise we end up configuring a potentially
improper state for the MPUSS. We also want to update the returned state
index for the selected state.
Let's just select the highest power idle state C1 to ensure no context
loss is allowed on cpu_cluster_pm_enter() errors. With these changes we
can now unconditionally call omap4_enter_lowpower() for WFI like we did
earlier before commit 55be2f5033 ("ARM: OMAP2+: Handle errors for
cpu_pm"). And we can return the selected state index.
Fixes: 8f04aea048 ("ARM: OMAP2+: Restore MPU power domain if cpu_cluster_pm_enter() fails")
Fixes: 55be2f5033 ("ARM: OMAP2+: Handle errors for cpu_pm")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e7ae08d398 ]
Bail out early from sysc_wait_softreset() just like we do in sysc_reset()
if there's no sysstatus srst_shift to fix a bogus resetdone warning on
enable as suggested by Grygorii Strashko <grygorii.strashko@ti.com>.
We do not currently handle resets for modules that need writing to the
sysstatus register. If we at some point add that, we also need to add
SYSS_QUIRK_RESETDONE_INVERTED flag for cpsw as the sysstatus bit is low
when reset is done as described in the am335x TRM "Table 14-202
SOFT_RESET Register Field Descriptions"
Fixes: d46f9fbec7 ("bus: ti-sysc: Use optional clocks on for enable and wait for softreset bit")
Suggested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a3dcb3e7e7 ]
When the switch is hardware reset, it reads the contents of the
EEPROM. This can contain instructions for programming values into
registers and to perform waits between such programming. Reading the
EEPROM can take longer than the 100ms mv88e6xxx_hardware_reset() waits
after deasserting the reset GPIO. So poll the EEPROM done bit to
ensure it is complete.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ruslan Sushko <rus@sushko.dev>
Link: https://lore.kernel.org/r/20201116164301.977661-1-rus@sushko.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f36199355c ]
Maurizio found a race where the abort and cmd stop paths can race as
follows:
1. thread1 runs iscsit_release_commands_from_conn and sets
CMD_T_FABRIC_STOP.
2. thread2 runs iscsit_aborted_task and then does __iscsit_free_cmd. It
then returns from the aborted_task callout and we finish
target_handle_abort and do:
target_handle_abort -> transport_cmd_check_stop_to_fabric ->
lio_check_stop_free -> target_put_sess_cmd
The cmd is now freed.
3. thread1 now finishes iscsit_release_commands_from_conn and runs
iscsit_free_cmd while accessing a command we just released.
In __target_check_io_state we check for CMD_T_FABRIC_STOP and set the
CMD_T_ABORTED if the driver is not cleaning up the cmd because of a session
shutdown. However, iscsit_release_commands_from_conn only sets the
CMD_T_FABRIC_STOP and does not check to see if the abort path has claimed
completion ownership of the command.
This adds a check in iscsit_release_commands_from_conn so only the abort or
fabric stop path cleanup the command.
Link: https://lore.kernel.org/r/1605318378-9269-1-git-send-email-michael.christie@oracle.com
Reported-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe0a8a95e7 ]
iSCSI NOPs are sometimes "lost", mistakenly sent to the user-land iscsid
daemon instead of handled in the kernel, as they should be, resulting in a
message from the daemon like:
iscsid: Got nop in, but kernel supports nop handling.
This can occur because of the new forward- and back-locks, and the fact
that an iSCSI NOP response can occur before processing of the NOP send is
complete. This can result in "conn->ping_task" being NULL in
iscsi_nop_out_rsp(), when the pointer is actually in the process of being
set.
To work around this, we add a new state to the "ping_task" pointer. In
addition to NULL (not assigned) and a pointer (assigned), we add the state
"being set", which is signaled with an INVALID pointer (using "-1").
Link: https://lore.kernel.org/r/20201106193317.16993-1-leeman.duncan@gmail.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 47a3565e8b ]
We might not do the final se_cmd put from vhost_scsi_complete_cmd_work.
When the last put happens a little later then we could race where
vhost_scsi_complete_cmd_work does vhost_signal, the guest runs and sends
more IO, and vhost_scsi_handle_vq runs but does not find any free cmds.
This patch has us delay completing the cmd until the last lio core ref
is dropped. We then know that once we signal to the guest that the cmd
is completed that if it queues a new command it will find a free cmd.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Reviewed-by: Maurizio Lombardi <mlombard@redhat.com>
Link: https://lore.kernel.org/r/1604986403-4931-4-git-send-email-michael.christie@oracle.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f0d2c876c ]
If Doorbell Buffer Config command fails even 'dev->dbbuf_dbs != NULL'
which means OACS indicates that NVME_CTRL_OACS_DBBUF_SUPP is set,
nvme_dbbuf_update_and_check_event() will check event even it's not been
successfully set.
This patch fixes mismatch among dbbuf for sq/cqs in case that dbbuf
command fails.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d4c3e76e3 ]
If this is attempted by a kthread, then return -EOPNOTSUPP as we don't
currently support that. Once we can get task_pid_ptr() doing the right
thing, then this can go away again.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7940fb035a ]
The battery status is also being reported by the logitech-hidpp driver,
so ignore the standard HID battery status to avoid reporting the same
info twice.
Note the logitech-hidpp battery driver provides more info, such as properly
differentiating between charging and discharging. Also the standard HID
battery info seems to be wrong, reporting a capacity of just 26% after
fully charging the device.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c27168a04a ]
Like the MX5000 and MX5500 quad/bluetooth keyboards the Dinovo Edge also
needs the HIDPP_CONSUMER_VENDOR_KEYS quirk for some special keys to work.
Specifically without this the "Phone" and the 'A' - 'D' Smart Keys do not
send any events.
In addition to fixing these keys not sending any events, adding the
Bluetooth match, so that hid-logitech-hidpp is used instead of the
generic HID driver, also adds battery monitoring support when the
keyboard is connected over Bluetooth.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65cae18882 ]
When booting a hyperthreaded system with the kernel parameter
'mitigations=auto,nosmt', the following warning occurs:
WARNING: CPU: 0 PID: 1 at drivers/xen/events/events_base.c:1112 unbind_from_irqhandler+0x4e/0x60
...
Hardware name: Xen HVM domU, BIOS 4.2.amazon 08/24/2006
...
Call Trace:
xen_uninit_lock_cpu+0x28/0x62
xen_hvm_cpu_die+0x21/0x30
takedown_cpu+0x9c/0xe0
? trace_suspend_resume+0x60/0x60
cpuhp_invoke_callback+0x9a/0x530
_cpu_up+0x11a/0x130
cpu_up+0x7e/0xc0
bringup_nonboot_cpus+0x48/0x50
smp_init+0x26/0x79
kernel_init_freeable+0xea/0x229
? rest_init+0xaa/0xaa
kernel_init+0xa/0x106
ret_from_fork+0x35/0x40
The secondary CPUs are not activated with the nosmt mitigations and only
the primary thread on each CPU core is used. In this situation,
xen_hvm_smp_prepare_cpus(), and more importantly xen_init_lock_cpu(), is
not called, so the lock_kicker_irq is not initialized for the secondary
CPUs. Let's fix this by exiting early in xen_uninit_lock_cpu() if the
irq is not set to avoid the warning from above for each secondary CPU.
Signed-off-by: Brian Masney <bmasney@redhat.com>
Link: https://lore.kernel.org/r/20201107011119.631442-1-bmasney@redhat.com
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f59ee399de ]
Kernel 5.4 introduces HID_QUIRK_INCREMENT_USAGE_ON_DUPLICATE, devices need to
be set explicitly with this flag.
Signed-off-by: Chris Ye <lzye@google.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 06ea594051 ]
When DMA_RALINK is enabled and DMADEVICES is disabled, it results in the
following Kbuild warnings:
WARNING: unmet direct dependencies detected for DMA_ENGINE
Depends on [n]: DMADEVICES [=n]
Selected by [y]:
- DMA_RALINK [=y] && STAGING [=y] && RALINK [=y] && !SOC_RT288X [=n]
WARNING: unmet direct dependencies detected for DMA_VIRTUAL_CHANNELS
Depends on [n]: DMADEVICES [=n]
Selected by [y]:
- DMA_RALINK [=y] && STAGING [=y] && RALINK [=y] && !SOC_RT288X [=n]
The reason is that DMA_RALINK selects DMA_ENGINE and DMA_VIRTUAL_CHANNELS
without depending on or selecting DMADEVICES while DMA_ENGINE and
DMA_VIRTUAL_CHANNELS are subordinate to DMADEVICES. This can also fail
building the kernel as demonstrated in a bug report.
Honor the kconfig dependency to remove unmet direct dependency warnings
and avoid any potential build failures.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=210055
Signed-off-by: Necip Fazil Yildiran <fazilyildiran@gmail.com>
Link: https://lore.kernel.org/r/20201104181522.43567-1-fazilyildiran@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 34a9fa2025 ]
Some HID devices don't use a report ID because they only have a single
report. In those cases, the report ID in struct hid_report will be zero
and the data for the report will start at the first byte, so don't skip
over the first byte.
Signed-off-by: Pablo Ceballos <pceballos@google.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1884583fc ]
The i8042 module exports several symbols which may be used by other
modules.
Before this commit it would refuse to load (when built as a module itself)
on systems without an i8042 controller.
This is a problem specifically for the asus-nb-wmi module. Many Asus
laptops support the Asus WMI interface. Some of them have an i8042
controller and need to use i8042_install_filter() to filter some kbd
events. Other models do not have an i8042 controller (e.g. they use an
USB attached kbd).
Before this commit the asus-nb-wmi driver could not be loaded on Asus
models without an i8042 controller, when the i8042 code was built as
a module (as Arch Linux does) because the module_init function of the
i8042 module would fail with -ENODEV and thus the i8042_install_filter
symbol could not be loaded.
This commit fixes this by exiting from module_init with a return code
of 0 if no controller is found. It also adds a i8042_present bool to
make the module_exit function a no-op in this case and also adds a
check for i8042_present to the exported i8042_command function.
The latter i8042_present check should not really be necessary because
when builtin that function can already be used on systems without
an i8042 controller, but better safe then sorry.
Reported-and-tested-by: Marius Iacob <themariusus@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20201008112628.3979-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1811977cb1 ]
This device needs HID_QUIRK_MULTI_INPUT in order to be presented to userspace
in a consistent way.
Reported-and-tested-by: David Gámiz Jiménez <david.gamiz@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 652f3d00de ]
The Varmilo VA104M Keyboard (04b4:07b1, reported as Varmilo Z104M)
exposes media control hotkeys as a USB HID consumer control device, but
these keys do not work in the current (5.8-rc1) kernel due to the
incorrect HID report descriptor. Fix the problem by modifying the
internal HID report descriptor.
More specifically, the keyboard report descriptor specifies the
logical boundary as 572~10754 (0x023c ~ 0x2a02) while the usage
boundary is specified as 0~10754 (0x00 ~ 0x2a02). This results in an
incorrect interpretation of input reports, causing inputs to be ignored.
By setting the Logical Minimum to zero, we align the logical boundary
with the Usage ID boundary.
Some notes:
* There seem to be multiple variants of the VA104M keyboard. This
patch specifically targets 04b4:07b1 variant.
* The device works out-of-the-box on Windows platform with the generic
consumer control device driver (hidserv.inf). This suggests that
Windows either ignores the Logical Minimum/Logical Maximum or
interprets the Usage ID assignment differently from the linux
implementation; Maybe there are other devices out there that only
works on Windows due to this problem?
Signed-off-by: Frank Yang <puilp0502@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c785a06de ]
The usb-hid keyboard-dock for the Acer Switch 10 SW5-012 model declares
an application and hid-usage page of 0x0088 for the INPUT(4) report which
it sends. This reports contains 2 8-bit fields which are declared as
HID_MAIN_ITEM_VARIABLE.
The keyboard-touchpad combo never actually generates this report, except
when the touchpad is toggled on/off with the Fn + F7 hotkey combo. The
toggle on/off is handled inside the keyboard-dock, when the touchpad is
toggled off it simply stops sending events.
When the touchpad is toggled on/off an INPUT(4) report is generated with
the first content byte set to 120/121, before this commit the kernel
would report this as ABS_MISC 120/121 events.
Patch the descriptor to replace the HID_MAIN_ITEM_VARIABLE with
HID_MAIN_ITEM_RELATIVE (because no key-presss release events are send)
and add mappings for the 0x00880078 and 0x00880079 usages to generate
touchpad on/off key events when the touchpad is toggled on/off.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 022fc5315b ]
The Trust Flex Design Tablet has an UGTizer USB ID and requires the same
initialization as the UGTizer GP0610 to be detected as a graphics tablet
instead of a mouse.
Signed-off-by: Martijn van de Streek <martijn@zeewinde.xyz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ff1712f953 upstream.
With hardware dirty bit management, calling pte_wrprotect() on a writable,
dirty PTE will lose the dirty state and return a read-only, clean entry.
Move the logic from ptep_set_wrprotect() into pte_wrprotect() to ensure that
the dirty bit is preserved for writable entries, as this is required for
soft-dirty bit management if we enable it in the future.
Cc: <stable@vger.kernel.org>
Fixes: 2f4b829c62 ("arm64: Add support for hardware updates of the access and dirty pte bits")
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20201120143557.6715-3-will@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07509e10dc upstream.
pte_accessible() is used by ptep_clear_flush() to figure out whether TLB
invalidation is necessary when unmapping pages for reclaim. Although our
implementation is correct according to the architecture, returning true
only for valid, young ptes in the absence of racing page-table
modifications, this is in fact flawed due to lazy invalidation of old
ptes in ptep_clear_flush_young() where we elide the expensive DSB
instruction for completing the TLB invalidation.
Rather than penalise the aging path, adjust pte_accessible() to return
true for any valid pte, even if the access flag is cleared.
Cc: <stable@vger.kernel.org>
Fixes: 76c714be0e ("arm64: pgtable: implement pte_accessible()")
Reported-by: Yu Zhao <yuzhao@google.com>
Acked-by: Yu Zhao <yuzhao@google.com>
Reviewed-by: Minchan Kim <minchan@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20201120143557.6715-2-will@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 71cc849b70 upstream.
kvm_cpu_accept_dm_intr and kvm_vcpu_ready_for_interrupt_injection are
a hodge-podge of conditions, hacked together to get something that
more or less works. But what is actually needed is much simpler;
in both cases the fundamental question is, do we have a place to stash
an interrupt if userspace does KVM_INTERRUPT?
In userspace irqchip mode, that is !vcpu->arch.interrupt.injected.
Currently kvm_event_needs_reinjection(vcpu) covers it, but it is
unnecessarily restrictive.
In split irqchip mode it's a bit more complicated, we need to check
kvm_apic_accept_pic_intr(vcpu) (the IRQ window exit is basically an INTACK
cycle and thus requires ExtINTs not to be masked) as well as
!pending_userspace_extint(vcpu). However, there is no need to
check kvm_event_needs_reinjection(vcpu), since split irqchip keeps
pending ExtINT state separate from event injection state, and checking
kvm_cpu_has_interrupt(vcpu) is wrong too since ExtINT has higher
priority than APIC interrupts. In fact the latter fixes a bug:
when userspace requests an IRQ window vmexit, an interrupt in the
local APIC can cause kvm_cpu_has_interrupt() to be true and thus
kvm_vcpu_ready_for_interrupt_injection() to return false. When this
happens, vcpu_run does not exit to userspace but the interrupt window
vmexits keep occurring. The VM loops without any hope of making progress.
Once we try to fix these with something like
return kvm_arch_interrupt_allowed(vcpu) &&
- !kvm_cpu_has_interrupt(vcpu) &&
- !kvm_event_needs_reinjection(vcpu) &&
- kvm_cpu_accept_dm_intr(vcpu);
+ (!lapic_in_kernel(vcpu)
+ ? !vcpu->arch.interrupt.injected
+ : (kvm_apic_accept_pic_intr(vcpu)
+ && !pending_userspace_extint(v)));
we realize two things. First, thanks to the previous patch the complex
conditional can reuse !kvm_cpu_has_extint(vcpu). Second, the interrupt
window request in vcpu_enter_guest()
bool req_int_win =
dm_request_for_irq_injection(vcpu) &&
kvm_cpu_accept_dm_intr(vcpu);
should be kept in sync with kvm_vcpu_ready_for_interrupt_injection():
it is unnecessary to ask the processor for an interrupt window
if we would not be able to return to userspace. Therefore,
kvm_cpu_accept_dm_intr(vcpu) is basically !kvm_cpu_has_extint(vcpu)
ANDed with the existing check for masked ExtINT. It all makes sense:
- we can accept an interrupt from userspace if there is a place
to stash it (and, for irqchip split, ExtINTs are not masked).
Interrupts from userspace _can_ be accepted even if right now
EFLAGS.IF=0.
- in order to tell userspace we will inject its interrupt ("IRQ
window open" i.e. kvm_vcpu_ready_for_interrupt_injection), both
KVM and the vCPU need to be ready to accept the interrupt.
... and this is what the patch implements.
Reported-by: David Woodhouse <dwmw@amazon.co.uk>
Analyzed-by: David Woodhouse <dwmw@amazon.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Nikos Tsironis <ntsironis@arrikto.com>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Tested-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 72c3bcdcda upstream.
Centralize handling of interrupts from the userspace APIC
in kvm_cpu_has_extint and kvm_cpu_get_extint, since
userspace APIC interrupts are handled more or less the
same as ExtINTs are with split irqchip. This removes
duplicated code from kvm_cpu_has_injectable_intr and
kvm_cpu_has_interrupt, and makes the code more similar
between kvm_cpu_has_{extint,interrupt} on one side
and kvm_cpu_get_{extint,interrupt} on the other.
Cc: stable@vger.kernel.org
Reviewed-by: Filippo Sironi <sironi@amazon.de>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Tested-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23bde34771 upstream.
It was recently reported that if GICR_TYPER is accessed before the RD base
address is set, we'll suffer from the unset @rdreg dereferencing. Oops...
gpa_t last_rdist_typer = rdreg->base + GICR_TYPER +
(rdreg->free_index - 1) * KVM_VGIC_V3_REDIST_SIZE;
It's "expected" that users will access registers in the redistributor if
the RD has been properly configured (e.g., the RD base address is set). But
it hasn't yet been covered by the existing documentation.
Per discussion on the list [1], the reporting of the GICR_TYPER.Last bit
for userspace never actually worked. And it's difficult for us to emulate
it correctly given that userspace has the flexibility to access it any
time. Let's just drop the reporting of the Last bit for userspace for now
(userspace should have full knowledge about it anyway) and it at least
prevents kernel from panic ;-)
[1] https://lore.kernel.org/kvmarm/c20865a267e44d1e2c0d52ce4e012263@kernel.org/
Fixes: ba7b3f1275 ("KVM: arm/arm64: Revisit Redistributor TYPER last bit computation")
Reported-by: Keqian Zhu <zhukeqian1@huawei.com>
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/r/20201117151629.1738-1-yuzenghui@huawei.com
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1254100030 upstream.
Mid callback needs to be called only when valid data is
read into pages.
These patches address a problem found during decryption offload:
CIFS: VFS: trying to dequeue a deleted mid
that could cause a refcount use after free:
Workqueue: smb3decryptd smb2_decrypt_offload [cifs]
Signed-off-by: Rohith Surabattula <rohiths@microsoft.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
CC: Stable <stable@vger.kernel.org> #5.4+
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ac873aa3dc upstream.
When reconnect happens Mid queue can be corrupted when both
demultiplex and offload thread try to dequeue the MID from the
pending list.
These patches address a problem found during decryption offload:
CIFS: VFS: trying to dequeue a deleted mid
that could cause a refcount use after free:
Workqueue: smb3decryptd smb2_decrypt_offload [cifs]
Signed-off-by: Rohith Surabattula <rohiths@microsoft.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
CC: Stable <stable@vger.kernel.org> #5.4+
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b9ae0c929 upstream.
When compiling inside the kernel include linux/stddef.h instead of
stddef.h. When I compile this header file in backports for power PC I
run into a conflict with ptrdiff_t. I was unable to reproduce this in
mainline kernel. I still would like to fix this problem in the kernel.
Fixes: 6989310f5d ("wireless: Use offsetof instead of custom macro.")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://lore.kernel.org/r/20200521201422.16493-1-hauke@hauke-m.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0697d9a610 upstream.
Syzbot reported a possible use-after-free when printing a duplicate device
warning device_list_add().
At this point it can happen that a btrfs_device::fs_info is not correctly
setup yet, so we're accessing stale data, when printing the warning
message using the btrfs_printk() wrappers.
==================================================================
BUG: KASAN: use-after-free in btrfs_printk+0x3eb/0x435 fs/btrfs/super.c:245
Read of size 8 at addr ffff8880878e06a8 by task syz-executor225/7068
CPU: 1 PID: 7068 Comm: syz-executor225 Not tainted 5.9.0-rc5-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1d6/0x29e lib/dump_stack.c:118
print_address_description+0x66/0x620 mm/kasan/report.c:383
__kasan_report mm/kasan/report.c:513 [inline]
kasan_report+0x132/0x1d0 mm/kasan/report.c:530
btrfs_printk+0x3eb/0x435 fs/btrfs/super.c:245
device_list_add+0x1a88/0x1d60 fs/btrfs/volumes.c:943
btrfs_scan_one_device+0x196/0x490 fs/btrfs/volumes.c:1359
btrfs_mount_root+0x48f/0xb60 fs/btrfs/super.c:1634
legacy_get_tree+0xea/0x180 fs/fs_context.c:592
vfs_get_tree+0x88/0x270 fs/super.c:1547
fc_mount fs/namespace.c:978 [inline]
vfs_kern_mount+0xc9/0x160 fs/namespace.c:1008
btrfs_mount+0x33c/0xae0 fs/btrfs/super.c:1732
legacy_get_tree+0xea/0x180 fs/fs_context.c:592
vfs_get_tree+0x88/0x270 fs/super.c:1547
do_new_mount fs/namespace.c:2875 [inline]
path_mount+0x179d/0x29e0 fs/namespace.c:3192
do_mount fs/namespace.c:3205 [inline]
__do_sys_mount fs/namespace.c:3413 [inline]
__se_sys_mount+0x126/0x180 fs/namespace.c:3390
do_syscall_64+0x31/0x70 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x44840a
RSP: 002b:00007ffedfffd608 EFLAGS: 00000293 ORIG_RAX: 00000000000000a5
RAX: ffffffffffffffda RBX: 00007ffedfffd670 RCX: 000000000044840a
RDX: 0000000020000000 RSI: 0000000020000100 RDI: 00007ffedfffd630
RBP: 00007ffedfffd630 R08: 00007ffedfffd670 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000293 R12: 000000000000001a
R13: 0000000000000004 R14: 0000000000000003 R15: 0000000000000003
Allocated by task 6945:
kasan_save_stack mm/kasan/common.c:48 [inline]
kasan_set_track mm/kasan/common.c:56 [inline]
__kasan_kmalloc+0x100/0x130 mm/kasan/common.c:461
kmalloc_node include/linux/slab.h:577 [inline]
kvmalloc_node+0x81/0x110 mm/util.c:574
kvmalloc include/linux/mm.h:757 [inline]
kvzalloc include/linux/mm.h:765 [inline]
btrfs_mount_root+0xd0/0xb60 fs/btrfs/super.c:1613
legacy_get_tree+0xea/0x180 fs/fs_context.c:592
vfs_get_tree+0x88/0x270 fs/super.c:1547
fc_mount fs/namespace.c:978 [inline]
vfs_kern_mount+0xc9/0x160 fs/namespace.c:1008
btrfs_mount+0x33c/0xae0 fs/btrfs/super.c:1732
legacy_get_tree+0xea/0x180 fs/fs_context.c:592
vfs_get_tree+0x88/0x270 fs/super.c:1547
do_new_mount fs/namespace.c:2875 [inline]
path_mount+0x179d/0x29e0 fs/namespace.c:3192
do_mount fs/namespace.c:3205 [inline]
__do_sys_mount fs/namespace.c:3413 [inline]
__se_sys_mount+0x126/0x180 fs/namespace.c:3390
do_syscall_64+0x31/0x70 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Freed by task 6945:
kasan_save_stack mm/kasan/common.c:48 [inline]
kasan_set_track+0x3d/0x70 mm/kasan/common.c:56
kasan_set_free_info+0x17/0x30 mm/kasan/generic.c:355
__kasan_slab_free+0xdd/0x110 mm/kasan/common.c:422
__cache_free mm/slab.c:3418 [inline]
kfree+0x113/0x200 mm/slab.c:3756
deactivate_locked_super+0xa7/0xf0 fs/super.c:335
btrfs_mount_root+0x72b/0xb60 fs/btrfs/super.c:1678
legacy_get_tree+0xea/0x180 fs/fs_context.c:592
vfs_get_tree+0x88/0x270 fs/super.c:1547
fc_mount fs/namespace.c:978 [inline]
vfs_kern_mount+0xc9/0x160 fs/namespace.c:1008
btrfs_mount+0x33c/0xae0 fs/btrfs/super.c:1732
legacy_get_tree+0xea/0x180 fs/fs_context.c:592
vfs_get_tree+0x88/0x270 fs/super.c:1547
do_new_mount fs/namespace.c:2875 [inline]
path_mount+0x179d/0x29e0 fs/namespace.c:3192
do_mount fs/namespace.c:3205 [inline]
__do_sys_mount fs/namespace.c:3413 [inline]
__se_sys_mount+0x126/0x180 fs/namespace.c:3390
do_syscall_64+0x31/0x70 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x44/0xa9
The buggy address belongs to the object at ffff8880878e0000
which belongs to the cache kmalloc-16k of size 16384
The buggy address is located 1704 bytes inside of
16384-byte region [ffff8880878e0000, ffff8880878e4000)
The buggy address belongs to the page:
page:0000000060704f30 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x878e0
head:0000000060704f30 order:3 compound_mapcount:0 compound_pincount:0
flags: 0xfffe0000010200(slab|head)
raw: 00fffe0000010200 ffffea00028e9a08 ffffea00021e3608 ffff8880aa440b00
raw: 0000000000000000 ffff8880878e0000 0000000100000001 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff8880878e0580: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff8880878e0600: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff8880878e0680: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff8880878e0700: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff8880878e0780: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
==================================================================
The syzkaller reproducer for this use-after-free crafts a filesystem image
and loop mounts it twice in a loop. The mount will fail as the crafted
image has an invalid chunk tree. When this happens btrfs_mount_root() will
call deactivate_locked_super(), which then cleans up fs_info and
fs_info::sb. If a second thread now adds the same block-device to the
filesystem, it will get detected as a duplicate device and
device_list_add() will reject the duplicate and print a warning. But as
the fs_info pointer passed in is non-NULL this will result in a
use-after-free.
Instead of printing possibly uninitialized or already freed memory in
btrfs_printk(), explicitly pass in a NULL fs_info so the printing of the
device name will be skipped altogether.
There was a slightly different approach discussed in
https://lore.kernel.org/linux-btrfs/20200114060920.4527-1-anand.jain@oracle.com/t/#u
Link: https://lore.kernel.org/linux-btrfs/000000000000c9e14b05afcc41ba@google.com
Reported-by: syzbot+582e66e5edf36a22c7b0@syzkaller.appspotmail.com
CC: stable@vger.kernel.org # 4.19+
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6d06b0ad94 upstream.
There are sectorsize alignment checks that are reported but then
check_extent_data_ref continues. This was not intended, wrong alignment
is not a minor problem and we should return with error.
CC: stable@vger.kernel.org # 5.4+
Fixes: 0785a9aacf ("btrfs: tree-checker: Add EXTENT_DATA_REF check")
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NF_HOOK_LIST() uses list_del() to remove skb from the linked list,
however, it is not sufficient as skb->next still points to other
skb. We should just call skb_list_del_init() to clear skb->next,
like the rest places which using skb list.
This has been fixed in upstream by commit ca58fbe06c
("netfilter: add and use nf_hook_slow_list()").
Fixes: 9f17dbf04d ("netfilter: fix use-after-free in NF_HOOK_LIST")
Reported-by: liuzx@knownsec.com
Tested-by: liuzx@knownsec.com
Cc: Florian Westphal <fw@strlen.de>
Cc: Edward Cree <ecree@solarflare.com>
Cc: stable@vger.kernel.org # between 4.19 and 5.4
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 63c5395bb7 upstream
bcm_qspi_remove() calls spi_unregister_master() even though
bcm_qspi_probe() calls devm_spi_register_master(). The spi_master is
therefore unregistered and freed twice on unbind.
Moreover, since commit 0392727c26 ("spi: bcm-qspi: Handle clock probe
deferral"), bcm_qspi_probe() leaks the spi_master allocation if the call
to devm_clk_get_optional() fails.
Fix by switching over to the new devm_spi_alloc_master() helper which
keeps the private data accessible until the driver has unbound and also
avoids the spi_master leak on probe.
While at it, fix an ordering issue in bcm_qspi_remove() wherein
spi_unregister_master() is called after uninitializing the hardware,
disabling the clock and freeing an IRQ data structure. The correct
order is to call spi_unregister_master() *before* those teardown steps
because bus accesses may still be ongoing until that function returns.
Fixes: fa236a7ef2 ("spi: bcm-qspi: Add Broadcom MSPI driver")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v4.9+: 123456789abc: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v4.9+
Cc: Kamal Dasu <kdasu.kdev@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/5e31a9a59fd1c0d0b795b2fe219f25e5ee855f9d.1605121038.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
[sudip: adjust context]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f80b08fc44 upstream.
When boosting is enabled, it is observed that rate of atomic order-0
allocation failures are high due to the fact that free levels in the
system are checked with ->watermark_boost offset. This is not a problem
for sleepable allocations but for atomic allocations which looks like
regression.
This problem is seen frequently on system setup of Android kernel running
on Snapdragon hardware with 4GB RAM size. When no extfrag event occurred
in the system, ->watermark_boost factor is zero, thus the watermark
configurations in the system are:
_watermark = (
[WMARK_MIN] = 1272, --> ~5MB
[WMARK_LOW] = 9067, --> ~36MB
[WMARK_HIGH] = 9385), --> ~38MB
watermark_boost = 0
After launching some memory hungry applications in Android which can cause
extfrag events in the system to an extent that ->watermark_boost can be
set to max i.e. default boost factor makes it to 150% of high watermark.
_watermark = (
[WMARK_MIN] = 1272, --> ~5MB
[WMARK_LOW] = 9067, --> ~36MB
[WMARK_HIGH] = 9385), --> ~38MB
watermark_boost = 14077, -->~57MB
With default system configuration, for an atomic order-0 allocation to
succeed, having free memory of ~2MB will suffice. But boosting makes the
min_wmark to ~61MB thus for an atomic order-0 allocation to be successful
system should have minimum of ~23MB of free memory(from calculations of
zone_watermark_ok(), min = 3/4(min/2)). But failures are observed despite
system is having ~20MB of free memory. In the testing, this is
reproducible as early as first 300secs since boot and with furtherlowram
configurations(<2GB) it is observed as early as first 150secs since boot.
These failures can be avoided by excluding the ->watermark_boost in
watermark caluculations for atomic order-0 allocations.
[akpm@linux-foundation.org: fix comment grammar, reflow comment]
[charante@codeaurora.org: fix suggested by Mel Gorman]
Link: http://lkml.kernel.org/r/31556793-57b1-1c21-1a9d-22674d9bd938@codeaurora.org
Signed-off-by: Charan Teja Reddy <charante@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Vinayak Menon <vinmenon@codeaurora.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Link: http://lkml.kernel.org/r/1589882284-21010-1-git-send-email-charante@codeaurora.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bfe8cc1db0 upstream.
Alexander reported a syzkaller / KASAN finding on s390, see below for
complete output.
In do_huge_pmd_anonymous_page(), the pre-allocated pagetable will be
freed in some cases. In the case of userfaultfd_missing(), this will
happen after calling handle_userfault(), which might have released the
mmap_lock. Therefore, the following pte_free(vma->vm_mm, pgtable) will
access an unstable vma->vm_mm, which could have been freed or re-used
already.
For all architectures other than s390 this will go w/o any negative
impact, because pte_free() simply frees the page and ignores the
passed-in mm. The implementation for SPARC32 would also access
mm->page_table_lock for pte_free(), but there is no THP support in
SPARC32, so the buggy code path will not be used there.
For s390, the mm->context.pgtable_list is being used to maintain the 2K
pagetable fragments, and operating on an already freed or even re-used
mm could result in various more or less subtle bugs due to list /
pagetable corruption.
Fix this by calling pte_free() before handle_userfault(), similar to how
it is already done in __do_huge_pmd_anonymous_page() for the WRITE /
non-huge_zero_page case.
Commit 6b251fc96c ("userfaultfd: call handle_userfault() for
userfaultfd_missing() faults") actually introduced both, the
do_huge_pmd_anonymous_page() and also __do_huge_pmd_anonymous_page()
changes wrt to calling handle_userfault(), but only in the latter case
it put the pte_free() before calling handle_userfault().
BUG: KASAN: use-after-free in do_huge_pmd_anonymous_page+0xcda/0xd90 mm/huge_memory.c:744
Read of size 8 at addr 00000000962d6988 by task syz-executor.0/9334
CPU: 1 PID: 9334 Comm: syz-executor.0 Not tainted 5.10.0-rc1-syzkaller-07083-g4c9720875573 #0
Hardware name: IBM 3906 M04 701 (KVM/Linux)
Call Trace:
do_huge_pmd_anonymous_page+0xcda/0xd90 mm/huge_memory.c:744
create_huge_pmd mm/memory.c:4256 [inline]
__handle_mm_fault+0xe6e/0x1068 mm/memory.c:4480
handle_mm_fault+0x288/0x748 mm/memory.c:4607
do_exception+0x394/0xae0 arch/s390/mm/fault.c:479
do_dat_exception+0x34/0x80 arch/s390/mm/fault.c:567
pgm_check_handler+0x1da/0x22c arch/s390/kernel/entry.S:706
copy_from_user_mvcos arch/s390/lib/uaccess.c:111 [inline]
raw_copy_from_user+0x3a/0x88 arch/s390/lib/uaccess.c:174
_copy_from_user+0x48/0xa8 lib/usercopy.c:16
copy_from_user include/linux/uaccess.h:192 [inline]
__do_sys_sigaltstack kernel/signal.c:4064 [inline]
__s390x_sys_sigaltstack+0xc8/0x240 kernel/signal.c:4060
system_call+0xe0/0x28c arch/s390/kernel/entry.S:415
Allocated by task 9334:
slab_alloc_node mm/slub.c:2891 [inline]
slab_alloc mm/slub.c:2899 [inline]
kmem_cache_alloc+0x118/0x348 mm/slub.c:2904
vm_area_dup+0x9c/0x2b8 kernel/fork.c:356
__split_vma+0xba/0x560 mm/mmap.c:2742
split_vma+0xca/0x108 mm/mmap.c:2800
mlock_fixup+0x4ae/0x600 mm/mlock.c:550
apply_vma_lock_flags+0x2c6/0x398 mm/mlock.c:619
do_mlock+0x1aa/0x718 mm/mlock.c:711
__do_sys_mlock2 mm/mlock.c:738 [inline]
__s390x_sys_mlock2+0x86/0xa8 mm/mlock.c:728
system_call+0xe0/0x28c arch/s390/kernel/entry.S:415
Freed by task 9333:
slab_free mm/slub.c:3142 [inline]
kmem_cache_free+0x7c/0x4b8 mm/slub.c:3158
__vma_adjust+0x7b2/0x2508 mm/mmap.c:960
vma_merge+0x87e/0xce0 mm/mmap.c:1209
userfaultfd_release+0x412/0x6b8 fs/userfaultfd.c:868
__fput+0x22c/0x7a8 fs/file_table.c:281
task_work_run+0x200/0x320 kernel/task_work.c:151
tracehook_notify_resume include/linux/tracehook.h:188 [inline]
do_notify_resume+0x100/0x148 arch/s390/kernel/signal.c:538
system_call+0xe6/0x28c arch/s390/kernel/entry.S:416
The buggy address belongs to the object at 00000000962d6948 which belongs to the cache vm_area_struct of size 200
The buggy address is located 64 bytes inside of 200-byte region [00000000962d6948, 00000000962d6a10)
The buggy address belongs to the page: page:00000000313a09fe refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x962d6 flags: 0x3ffff00000000200(slab)
raw: 3ffff00000000200 000040000257e080 0000000c0000000c 000000008020ba00
raw: 0000000000000000 000f001e00000000 ffffffff00000001 0000000096959501
page dumped because: kasan: bad access detected
page->mem_cgroup:0000000096959501
Memory state around the buggy address:
00000000962d6880: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00000000962d6900: 00 fc fc fc fc fc fc fc fc fa fb fb fb fb fb fb
>00000000962d6980: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
00000000962d6a00: fb fb fc fc fc fc fc fc fc fc 00 00 00 00 00 00
00000000962d6a80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
==================================================================
Fixes: 6b251fc96c ("userfaultfd: call handle_userfault() for userfaultfd_missing() faults")
Reported-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Signed-off-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: <stable@vger.kernel.org> [4.3+]
Link: https://lkml.kernel.org/r/20201110190329.11920-1-gerald.schaefer@linux.ibm.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a371e67dc upstream.
Currently, scan_microcode() leverages microcode_matches() to check
if the microcode matches the CPU by comparing the family and model.
However, the processor stepping and flags of the microcode signature
should also be considered when saving a microcode patch for early
update.
Use find_matching_signature() in scan_microcode() and get rid of the
now-unused microcode_matches() which is a good cleanup in itself.
Complete the verification of the patch being saved for early loading in
save_microcode_patch() directly. This needs to be done there too because
save_mc_for_early() will call save_microcode_patch() too.
The second reason why this needs to be done is because the loader still
tries to support, at least hypothetically, mixed-steppings systems and
thus adds all patches to the cache that belong to the same CPU model
albeit with different steppings.
For example:
microcode: CPU: sig=0x906ec, pf=0x2, rev=0xd6
microcode: mc_saved[0]: sig=0x906e9, pf=0x2a, rev=0xd6, total size=0x19400, date = 2020-04-23
microcode: mc_saved[1]: sig=0x906ea, pf=0x22, rev=0xd6, total size=0x19000, date = 2020-04-27
microcode: mc_saved[2]: sig=0x906eb, pf=0x2, rev=0xd6, total size=0x19400, date = 2020-04-23
microcode: mc_saved[3]: sig=0x906ec, pf=0x22, rev=0xd6, total size=0x19000, date = 2020-04-27
microcode: mc_saved[4]: sig=0x906ed, pf=0x22, rev=0xd6, total size=0x19400, date = 2020-04-23
The patch which is being saved for early loading, however, can only be
the one which fits the CPU this runs on so do the signature verification
before saving.
[ bp: Do signature verification in save_microcode_patch()
and rewrite commit message. ]
Fixes: ec400ddeff ("x86/microcode_intel_early.c: Early update ucode on Intel's CPU")
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: stable@vger.kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=208535
Link: https://lkml.kernel.org/r/20201113015923.13960-1-yu.c.chen@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 60d5356610 upstream.
A UHS setting of SDR25 can give better results for High Speed mode.
This is because there is no setting corresponding to high speed. Currently
SDHCI sets no value, which means zero which is also the setting for SDR12.
There was an attempt to change this in sdhci.c but it caused problems for
some drivers, so it was reverted and the change was made to sdhci-brcmstb
in commit 2fefc7c5f7 ("mmc: sdhci-brcmstb: Fix incorrect switch to HS
mode"). Several other drivers also do this.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v5.4+
Link: https://lore.kernel.org/r/20201112133656.20317-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d2e3fce9dd upstream.
EDID can declare the maximum supported bpc up to 16,
and apparently there are displays that do so. Currently
we assume 12 bpc is tha max. Fix the assumption and
toss in a MISSING_CASE() for any other value we don't
expect to see.
This fixes modesets with a display with EDID max bpc > 12.
Previously any modeset would just silently fail on platforms
that didn't otherwise limit this via the max_bpc property.
In particular we don't add the max_bpc property to HDMI
ports on gmch platforms, and thus we would see the raw
max_bpc coming from the EDID.
I suppose we could already adjust this to also allow 16bpc,
but seeing as no current platform supports that there is
little point.
Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2632
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201110210447.27454-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
(cherry picked from commit 2ca5a7b85b)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 92e4dc8b05 upstream.
When invoking kexec() on a Linux guest running on a Hyper-V host, the
kernel panics.
RIP: 0010:cpuhp_issue_call+0x137/0x140
Call Trace:
__cpuhp_remove_state_cpuslocked+0x99/0x100
__cpuhp_remove_state+0x1c/0x30
hv_kexec_handler+0x23/0x30 [hv_vmbus]
hv_machine_shutdown+0x1e/0x30
machine_shutdown+0x10/0x20
kernel_kexec+0x6d/0x96
__do_sys_reboot+0x1ef/0x230
__x64_sys_reboot+0x1d/0x20
do_syscall_64+0x6b/0x3d8
entry_SYSCALL_64_after_hwframe+0x44/0xa9
This was due to hv_synic_cleanup() callback returning -EBUSY to
cpuhp_issue_call() when tearing down the VMBUS_CONNECT_CPU, even
if the vmbus_connection.conn_state = DISCONNECTED. hv_synic_cleanup()
should succeed in the case where vmbus_connection.conn_state
is DISCONNECTED.
Fix is to add an extra condition to test for
vmbus_connection.conn_state == CONNECTED on the VMBUS_CONNECT_CPU and
only return early if true. This way the kexec() path can still shut
everything down while preserving the initial behavior of preventing
CPU offlining on the VMBUS_CONNECT_CPU while the VM is running.
Fixes: 8a857c5542 ("Drivers: hv: vmbus: Always handle the VMBus messages on CPU0")
Signed-off-by: Chris Co <chrco@microsoft.com>
Reviewed-by: Andrea Parri (Microsoft) <parri.andrea@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20201110190118.15596-1-chrco@linux.microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f117cb854 upstream.
When requeueing all requests on the device request queue to the blocklayer
we might get to an ERP (error recovery) request that is a copy of an
original CQR.
Those requests do not have blocklayer request information or a pointer to
the dasd_queue set. When trying to access those data it will lead to a
null pointer dereference in dasd_requeue_all_requests().
Fix by checking if the request is an ERP request that can simply be
ignored. The blocklayer request will be requeued by the original CQR that
is on the device queue right behind the ERP request.
Fixes: 9487cfd343 ("s390/dasd: fix handling of internal requests")
Cc: <stable@vger.kernel.org> #4.16
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 78d732e1f3 upstream.
This file is installed by the s390 CPU Measurement sampling
facility device driver to export supported minimum and
maximum sample buffer sizes.
This file is read by lscpumf tool to display the details
of the device driver capabilities. The lscpumf tool might
be invoked by a non-root user. In this case it does not
print anything because the file contents can not be read.
Fix this by allowing read access for all users. Reading
the file contents is ok, changing the file contents is
left to the root user only.
For further reference and details see:
[1] https://github.com/ibm-s390-tools/s390-tools/issues/97
Fixes: 69f239ed33 ("s390/cpum_sf: Dynamically extend the sampling buffer if overflows occur")
Cc: <stable@vger.kernel.org> # 3.14
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Acked-by: Sumanth Korikkar <sumanthk@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4fe40b8e15 upstream.
Deferring sampling attempts to the second stage has some bad interactions
with drivers that process the rate table in hardware and use the probe flag
to indicate probing packets (e.g. most mt76 drivers). On affected drivers
it can lead to probing not working at all.
If the link conditions turn worse, it might not be such a good idea to
do a lot of sampling for lower rates in this case.
Fix this by simply skipping the sample attempt instead of deferring it,
but keep the checks that would allow it to be sampled if it was skipped
too often, but only if it has less than 95% success probability.
Also ensure that IEEE80211_TX_CTL_RATE_CTRL_PROBE is set for all probing
packets.
Cc: stable@vger.kernel.org
Fixes: cccf129f82 ("mac80211: add the 'minstrel' rate control algorithm")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20201111183359.43528-2-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a860d165e upstream.
Although cache alias management calls set up and tear down TLB entries
and fast_second_level_miss is able to restore TLB entry should it be
evicted they absolutely cannot preempt each other because they use the
same TLBTEMP area for different purposes.
Disable preemption around all cache alias management calls to enforce
that.
Cc: stable@vger.kernel.org
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 481535c5b4 upstream.
fast_second_level_miss handler for the TLBTEMP area has an assumption
that page table directory entry for the TLBTEMP address range is 0. For
it to be true the TLBTEMP area must be aligned to 4MB boundary and not
share its 4MB region with anything that may use a page table. This is
not true currently: TLBTEMP shares space with vmalloc space which
results in the following kinds of runtime errors when
fast_second_level_miss loads page table directory entry for the vmalloc
space instead of fixing up the TLBTEMP area:
Unable to handle kernel paging request at virtual address c7ff0e00
pc = d0009275, ra = 90009478
Oops: sig: 9 [#1] PREEMPT
CPU: 1 PID: 61 Comm: kworker/u9:2 Not tainted 5.10.0-rc3-next-20201110-00007-g1fe4962fa983-dirty #58
Workqueue: xprtiod xs_stream_data_receive_workfn
a00: 90009478 d11e1dc0 c7ff0e00 00000020 c7ff0000 00000001 7f8b8107 00000000
a08: 900c5992 d11e1d90 d0cc88b8 5506e97c 00000000 5506e97c d06c8074 d11e1d90
pc: d0009275, ps: 00060310, depc: 00000014, excvaddr: c7ff0e00
lbeg: d0009275, lend: d0009287 lcount: 00000003, sar: 00000010
Call Trace:
xs_stream_data_receive_workfn+0x43c/0x770
process_one_work+0x1a1/0x324
worker_thread+0x1cc/0x3c0
kthread+0x10d/0x124
ret_from_kernel_thread+0xc/0x18
Cc: stable@vger.kernel.org
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e844cc37a upstream.
SPI driver probing currently comprises two steps, whereas removal
comprises only one step:
spi_alloc_master()
spi_register_controller()
spi_unregister_controller()
That's because spi_unregister_controller() calls device_unregister()
instead of device_del(), thereby releasing the reference on the
spi_controller which was obtained by spi_alloc_master().
An SPI driver's private data is contained in the same memory allocation
as the spi_controller struct. Thus, once spi_unregister_controller()
has been called, the private data is inaccessible. But some drivers
need to access it after spi_unregister_controller() to perform further
teardown steps.
Introduce devm_spi_alloc_master() and devm_spi_alloc_slave(), which
release a reference on the spi_controller struct only after the driver
has unbound, thereby keeping the memory allocation accessible. Change
spi_unregister_controller() to not release a reference if the
spi_controller was allocated by one of these new devm functions.
The present commit is small enough to be backportable to stable.
It allows fixing drivers which use the private data in their ->remove()
hook after it's been freed. It also allows fixing drivers which neglect
to release a reference on the spi_controller in the probe error path.
Long-term, most SPI drivers shall be moved over to the devm functions
introduced herein. The few that can't shall be changed in a treewide
commit to explicitly release the last reference on the controller.
That commit shall amend spi_unregister_controller() to no longer release
a reference, thereby completing the migration.
As a result, the behaviour will be less surprising and more consistent
with subsystems such as IIO, which also includes the private data in the
allocation of the generic iio_dev struct, but calls device_del() in
iio_device_unregister().
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/272bae2ef08abd21388c98e23729886663d19192.1605121038.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4def49da62 upstream.
Normally the last reference on an spi_controller is released by
spi_unregister_controller(). In the case of the i.MX lpspi driver,
the spi_controller is registered with devm_spi_register_controller(),
so spi_unregister_controller() is invoked automatically after the driver
has unbound.
However the driver already releases the last reference in
fsl_lpspi_remove() through a gratuitous call to spi_master_put(),
causing a use-after-free when spi_unregister_controller() is
subsequently invoked by the devres framework.
Fix by dropping the superfluous spi_master_put().
Fixes: 944c01a889 ("spi: lpspi: enable runtime pm for lpspi")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v5.2+
Cc: Han Xu <han.xu@nxp.com>
Link: https://lore.kernel.org/r/ab3c0b18bd820501a12c85e440006e09ec0e275f.1604874488.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e5b1032a65 upstream.
Some 360 degree hinges (yoga) style 2-in-1 devices use 2 KXCJ91008-s
to allow the OS to determine the angle between the display and the base
of the device, so that the OS can determine if the 2-in-1 is in laptop
or in tablet-mode.
On Windows both accelerometers are read by a special HingeAngleService
process; and this process calls a DSM (Device Specific Method) on the
ACPI KIOX010A device node for the sensor in the display, to let the
embedded-controller (EC) know about the mode so that it can disable the
kbd and touchpad to avoid spurious input while folded into tablet-mode.
This notifying of the EC is problematic because sometimes the EC comes up
thinking that device is in tablet-mode and the kbd and touchpad do not
work. This happens for example on Irbis NB111 devices after a suspend /
resume cycle (after a complete battery drain / hard reset without having
booted Windows at least once). Other 2-in-1s which are likely affected
too are e.g. the Teclast F5 and F6 series.
The kxcjk-1013 driver may seem like a strange place to deal with this,
but since it is *the* driver for the ACPI KIOX010A device, it is also
the driver which has access to the ACPI handle needed by the DSM.
Add support for calling the DSM and on probe unconditionally tell the
EC that the device is laptop mode, fixing the kbd and touchpad sometimes
not working.
Fixes: 7f6232e695 ("iio: accel: kxcjk1013: Add KIOX010A ACPI Hardware-ID")
Reported-and-tested-by: russianneuromancer <russianneuromancer@ya.ru>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201110133835.129080-3-hdegoede@redhat.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f902b21650 upstream.
The idea of the warning in ext4_update_dx_flag() is that we should warn
when we are clearing EXT4_INODE_INDEX on a filesystem with metadata
checksums enabled since after clearing the flag, checksums for internal
htree nodes will become invalid. So there's no need to warn (or actually
do anything) when EXT4_INODE_INDEX is not set.
Link: https://lore.kernel.org/r/20201118153032.17281-1-jack@suse.cz
Fixes: 48a3431195 ("ext4: fix checksum errors with indexed dirs")
Reported-by: Eric Biggers <ebiggers@kernel.org>
Reviewed-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 44a146a44f upstream.
When VCNL4035 is enabled and IIO_BUFFER is disabled, it results in the
following Kbuild warning:
WARNING: unmet direct dependencies detected for IIO_TRIGGERED_BUFFER
Depends on [n]: IIO [=y] && IIO_BUFFER [=n]
Selected by [y]:
- VCNL4035 [=y] && IIO [=y] && I2C [=y]
The reason is that VCNL4035 selects IIO_TRIGGERED_BUFFER without depending
on or selecting IIO_BUFFER while IIO_TRIGGERED_BUFFER depends on
IIO_BUFFER. This can also fail building the kernel.
Honor the kconfig dependency to remove unmet direct dependency warnings
and avoid any potential build failures.
Fixes: 55707294c4 ("iio: light: Add support for vishay vcnl4035")
Signed-off-by: Necip Fazil Yildiran <fazilyildiran@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209883
Link: https://lore.kernel.org/r/20201102223523.572461-1-fazilyildiran@gmail.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eec231e060 upstream.
Fix an error in the mouse / INPUT(2) descriptor used for quad/bt2.0 combo
receivers. Replace INPUT with INPUT (Data,Var,Abs) for the field for the
4 extra buttons which share their report-byte with the low-res hwheel.
This is likely a copy and paste error. I've verified that the new
0x81, 0x02 value matches both the mouse descriptor for the currently
supported MX5000 / MX5500 receivers, as well as the INPUT(2) mouse
descriptors for the Dinovo receivers for which support is being
worked on.
Cc: stable@vger.kernel.org
Fixes: f2113c3020 ("HID: logitech-dj: add support for Logitech Bluetooth Mini-Receiver")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 33f16855dc upstream.
Enabling the lock dependency validator has revealed
that the way spinlocks are used in the IMX serial
port could result in a deadlock.
Specifically, imx_uart_int() acquires a spinlock
without disabling the interrupts, meaning that another
interrupt could come along and try to acquire the same
spinlock, potentially causing the two to wait for each
other indefinitely.
Use spin_lock_irqsave() instead to disable interrupts
upon acquisition of the spinlock.
Fixes: c974991d26 ("tty:serial:imx: use spin_lock instead of spin_lock_irqsave in isr")
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sam Nobs <samuel.nobs@taitradio.com>
Link: https://lore.kernel.org/r/1604955006-9363-1-git-send-email-samuel.nobs@taitradio.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d21b96c8ed upstream.
The code change for switching to non-atomic mode brought the
unexpected mutex deadlock in get_msg(). It converted the spinlock
with the existing mutex, but there were calls with the already holding
the mutex. Since the only place that needs the extra lock is the code
path from snd_mixart_send_msg(), remove the mutex lock in get_msg()
and apply in the caller side for fixing the mutex deadlock.
Fixes: 8d3a8b5cb5 ("ALSA: mixart: Use nonatomic PCM ops")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201119121440.18945-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 95a793c3bc upstream.
When processing request to add/replace user-defined element set, check
of given element identifier and decision of numeric identifier is done
in "__snd_ctl_add_replace()" helper function. When the result of check
is wrong, the helper function returns error code. The error code shall
be returned to userspace application.
Current implementation includes bug to return zero to userspace application
regardless of the result. This commit fixes the bug.
Cc: <stable@vger.kernel.org>
Fixes: e1a7bfe380 ("ALSA: control: Fix race between adding and removing a user element")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20201113092043.16148-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 02a9c6ee41 upstream.
The spin_lock/unlock_irq() functions cannot be nested. The problem is
that presumably we would want the IRQs to be re-enabled on the second
call the spin_unlock_irq() but instead it will be enabled at the first
call so IRQs will be enabled earlier than expected.
In this situation the copy_resp_to_buf() function is only called from
one function and it is called with IRQs disabled. We can just use
the regular spin_lock/unlock() functions.
Fixes: 555e8a8f7f ("ALSA: fireworks: Add command/response functionality into hwdep interface")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201113101241.GB168908@mwanda
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d412275444 upstream.
Speakup has only one speakup_tty variable to store the tty it is managing. This
makes sense since its codebase currently assumes that there is only one user who
controls the screen reading.
That however means that we have to forbid using the line discipline several
times, otherwise the second closure would try to free a NULL ldisc_data, leading to
general protection fault: 0000 [#1] SMP KASAN PTI
RIP: 0010:spk_ttyio_ldisc_close+0x2c/0x60
Call Trace:
tty_ldisc_release+0xa2/0x340
tty_release_struct+0x17/0xd0
tty_release+0x9d9/0xcc0
__fput+0x231/0x740
task_work_run+0x12c/0x1a0
do_exit+0x9b5/0x2230
? release_task+0x1240/0x1240
? __do_page_fault+0x562/0xa30
do_group_exit+0xd5/0x2a0
__x64_sys_exit_group+0x35/0x40
do_syscall_64+0x89/0x2b0
? page_fault+0x8/0x30
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Cc: stable@vger.kernel.org
Reported-by: 秦世松 <qinshisong1205@gmail.com>
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Tested-by: Shisong Qin <qinshisong1205@gmail.com>
Link: https://lore.kernel.org/r/20201110183541.fzgnlwhjpgqzjeth@function
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b4c00e7976 ]
Some users are pairing the Dinovo keyboards with the MX5000 or MX5500
receivers, instead of with the Dinovo receivers. The receivers are
mostly the same (and the air protocol obviously is compatible) but
currently the Dinovo receivers are handled by hid-lg.c while the
MX5x00 receivers are handled by logitech-dj.c.
When using a Dinovo keyboard, with its builtin touchpad, through
logitech-dj.c then the touchpad stops working because when asking the
receiver for paired devices, we get only 1 paired device with
a device_type of REPORT_TYPE_KEYBOARD. And since we don't see a paired
mouse, we have nowhere to send mouse-events to, so we drop them.
Extend the existing fix for the Dinovo Edge for this to also cover the
Dinovo Mini keyboard and also add a mapping to logitech-hidpp for the
Media key on the Dinovo Mini, so that that keeps working too.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1811424
Fixes: f2113c3020 ("HID: logitech-dj: add support for Logitech Bluetooth Mini-Receiver")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee5e58418a ]
Some quad/bluetooth keyboards, such as the Dinovo Edge (Y-RAY81) have a
builtin touchpad. In this case when asking the receiver for paired devices,
we get only 1 paired device with a device_type of REPORT_TYPE_KEYBOARD.
This means that we do not instantiate a second dj_hiddev for the mouse
(as we normally would) and thus there is no place for us to forward the
mouse input reports to, causing the touchpad part of the keyboard to not
work.
There is no way for us to detect these keyboards, so this commit adds
an array with device-ids for such keyboards and when a keyboard is on
this list it adds STD_MOUSE to the reports_supported bitmap for the
dj_hiddev created for the keyboard fixing the touchpad not working.
Using a list of device-ids for this is not ideal, but there are only
very few such keyboards so this should be fine. Besides the Dinovo Edge,
other known wireless Logitech keyboards with a builtin touchpad are:
* Dinovo Mini (TODO add its device-id to the list)
* K400 (uses a unifying receiver so is not affected)
* K600 (uses a unifying receiver so is not affected)
Cc: stable@vger.kernel.org
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1811424
Fixes: f2113c3020 ("HID: logitech-dj: add support for Logitech Bluetooth Mini-Receiver")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b59f38dbfd ]
It seems that the PID 0x4072 was missing from the list Logitech gave me
for this mouse, as I found one with it in the wild (with which I tested
this patch).
Fixes: 4435ff2f09 ("HID: logitech: Enable high-resolution scrolling on Logitech mice")
Signed-off-by: Harry Cutts <hcutts@chromium.org>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 488dac0c92 ]
The attr->set() receive a value of u64, but simple_strtoll() is used for
doing the conversion. It will lead to the error cast if user inputs a
negative value.
Use kstrtoull() instead of simple_strtoll() to convert a string got from
the user to an unsigned value. The former will return '-EINVAL' if it
gets a negetive value, but the latter can't handle the situation
correctly. Make 'val' unsigned long long as what kstrtoull() takes,
this will eliminate the compile warning on no 64-bit architectures.
Fixes: f7b88631a8 ("fs/libfs.c: fix simple_attr_write() on 32bit machines")
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Link: https://lkml.kernel.org/r/1605341356-11872-1-git-send-email-yangyicong@hisilicon.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2fe61d8be ]
Commit
d9e9a64180 ("x86/mm/pti: Allocate a separate user PGD")
changed the PGD allocation to allocate PGD_ALLOCATION_ORDER pages, so in
the error path it should be freed using free_pages() rather than
free_page().
Commit
06ace26f4e ("x86/efi: Free efi_pgd with free_pages()")
fixed one instance of this, but missed another.
Move the freeing out-of-line to avoid code duplication and fix this bug.
Fixes: d9e9a64180 ("x86/mm/pti: Allocate a separate user PGD")
Link: https://lore.kernel.org/r/20201110163919.1134431-1-nivedita@alum.mit.edu
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6fa9201a89 ]
If a socket redirects to itself and it is under memory pressure it is
possible to get a socket stuck so that recv() returns EAGAIN and the
socket can not advance for some time. This happens because when
redirecting a skb to the same socket we received the skb on we first
check if it is OK to enqueue the skb on the receiving socket by checking
memory limits. But, if the skb is itself the object holding the memory
needed to enqueue the skb we will keep retrying from kernel side
and always fail with EAGAIN. Then userspace will get a recv() EAGAIN
error if there are no skbs in the psock ingress queue. This will continue
until either some skbs get kfree'd causing the memory pressure to
reduce far enough that we can enqueue the pending packet or the
socket is destroyed. In some cases its possible to get a socket
stuck for a noticeable amount of time if the socket is only receiving
skbs from sk_skb verdict programs. To reproduce I make the socket
memory limits ridiculously low so sockets are always under memory
pressure. More often though if under memory pressure it looks like
a spurious EAGAIN error on user space side causing userspace to retry
and typically enough has moved on the memory side that it works.
To fix skip memory checks and skb_orphan if receiving on the same
sock as already assigned.
For SK_PASS cases this is easy, its always the same socket so we
can just omit the orphan/set_owner pair.
For backlog cases we need to check skb->sk and decide if the orphan
and set_owner pair are needed.
Fixes: 51199405f9 ("bpf: skb_verdict, support SK_PASS on RX BPF path")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/bpf/160556572660.73229.12566203819812939627.stgit@john-XPS-13-9370
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ecbfb06a0 ]
When we receive an skb and the ingress skb verdict program returns
SK_PASS we currently set the ingress flag and put it on the workqueue
so it can be turned into a sk_msg and put on the sk_msg ingress queue.
Then finally telling userspace with data_ready hook.
Here we observe that if the workqueue is empty then we can try to
convert into a sk_msg type and call data_ready directly without
bouncing through a workqueue. Its a common pattern to have a recv
verdict program for visibility that always returns SK_PASS. In this
case unless there is an ENOMEM error or we overrun the socket we
can avoid the workqueue completely only using it when we fall back
to error cases caused by memory pressure.
By doing this we eliminate another case where data may be dropped
if errors occur on memory limits in workqueue.
Fixes: 51199405f9 ("bpf: skb_verdict, support SK_PASS on RX BPF path")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/160226859704.5692.12929678876744977669.stgit@john-Precision-5820-Tower
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cfea28f890 ]
For sk_skb case where skb_verdict program returns SK_PASS to continue to
pass packet up the stack, the memory limits were already checked before
enqueuing in skb_queue_tail from TCP side. So, lets remove the extra checks
here. The theory is if the TCP stack believes we have memory to receive
the packet then lets trust the stack and not double check the limits.
In fact the accounting here can cause a drop if sk_rmem_alloc has increased
after the stack accepted this packet, but before the duplicate check here.
And worse if this happens because TCP stack already believes the data has
been received there is no retransmit.
Fixes: 51199405f9 ("bpf: skb_verdict, support SK_PASS on RX BPF path")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/160226857664.5692.668205469388498375.stgit@john-Precision-5820-Tower
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb8409071a ]
This reverts commit 6ff646b2ce.
Your maintainer committed a major braino in the rmap code by adding the
attr fork, bmbt, and unwritten extent usage bits into rmap record key
comparisons. While XFS uses the usage bits *in the rmap records* for
cross-referencing metadata in xfs_scrub and xfs_repair, it only needs
the owner and offset information to distinguish between reverse mappings
of the same physical extent into the data fork of a file at multiple
offsets. The other bits are not important for key comparisons for index
lookups, and never have been.
Eric Sandeen reports that this causes regressions in generic/299, so
undo this patch before it does more damage.
Reported-by: Eric Sandeen <sandeen@sandeen.net>
Fixes: 6ff646b2ce ("xfs: fix rmap key and record comparison functions")
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ba546ebe0 ]
At the start of driver initialization, we do not know what bias
setting the bootloader has configured the system for and we only know
for certain the very first time we do a transition.
However, since the initial value of the comparison index is -EINVAL,
this negative value results in an array out of bound access on the
very first transition.
Since we don't know what the setting is, we just set the bias
configuration as there is nothing to compare against. This prevents
the array out of bound access.
NOTE: Even though we could use a more relaxed check of "< 0" the only
valid values(ignoring cosmic ray induced bitflips) are -EINVAL, 0+.
Fixes: 40b1936efe ("regulator: Introduce TI Adaptive Body Bias(ABB) on-chip LDO driver")
Link: https://lore.kernel.org/linux-mm/CA+G9fYuk4imvhyCN7D7T6PMDH6oNp6HDCRiTUKMQ6QXXjBa4ag@mail.gmail.com/
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20201118145009.10492-1-nm@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 595189c25c ]
In xfs_initialize_perag(), if kmem_zalloc(), xfs_buf_hash_init(), or
radix_tree_preload() failed, the returned value 'error' is not set
accordingly.
Reported-as-fixing: 8b26c5825e ("xfs: handle ENOMEM correctly during initialisation of perag structures")
Fixes: 9b24717979 ("xfs: cache unlinked pointers in an rhashtable")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 498fe261f0 ]
We always know the correct state of the rmap record flags (attr, bmbt,
unwritten) so check them by direct comparison.
Fixes: d852657ccf ("xfs: cross-reference reverse-mapping btree")
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e95b6c3ef1 ]
The comment and logic in xchk_btree_check_minrecs for dealing with
inode-rooted btrees isn't quite correct. While the direct children of
the inode root are allowed to have fewer records than what would
normally be allowed for a regular ondisk btree block, this is only true
if there is only one child block and the number of records don't fit in
the inode root.
Fixes: 08a3a692ef ("xfs: btree scrub should check minrecs")
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd9f13c594 ]
If the CAN controller goes into bus off, the do_set_mode() callback with
CAN_MODE_START can be used to recover the controller, which then calls
flexcan_chip_start(). If configured, this is done automatically by the
framework or manually by the user.
In flexcan_chip_start() there is an explicit call to
flexcan_transceiver_enable(), which does a regulator_enable() on the
transceiver regulator. This results in a net usage counter increase, as there
is no corresponding flexcan_transceiver_disable() in the bus off code path.
This further leads to the transceiver stuck enabled, even if the CAN interface
is shut down.
To fix this problem the
flexcan_transceiver_enable()/flexcan_transceiver_disable() are moved out of
flexcan_chip_start()/flexcan_chip_stop() into flexcan_open()/flexcan_close().
Fixes: e955cead03 ("CAN: Add Flexcan CAN controller driver")
Link: https://lore.kernel.org/r/20201118150148.2664024-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4d213e76a3 ]
"intel_iommu=off" command line is used to disable iommu but iommu is force
enabled in a tboot system for security reason.
However for better performance on high speed network device, a new option
"intel_iommu=tboot_noforce" is introduced to disable the force on.
By default kernel should panic if iommu init fail in tboot for security
reason, but it's unnecessory if we use "intel_iommu=tboot_noforce,off".
Fix the code setting force_on and move intel_iommu_tboot_noforce
from tboot code to intel iommu code.
Fixes: 7304e8f28b ("iommu/vt-d: Correctly disable Intel IOMMU force on")
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@gmail.com>
Tested-by: Lukasz Hawrylko <lukasz.hawrylko@linux.intel.com>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20201110071908.3133-1-zhenzhong.duan@gmail.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c9c89dcd87 ]
If copy_page_to_iter() fails or even partially completes, but with fewer
bytes copied than expected we currently reset sg.start and return EFAULT.
This proves problematic if we already copied data into the user buffer
before we return an error. Because we leave the copied data in the user
buffer and fail to unwind the scatterlist so kernel side believes data
has been copied and user side believes data has _not_ been received.
Expected behavior should be to return number of bytes copied and then
on the next read we need to return the error assuming its still there. This
can happen if we have a copy length spanning multiple scatterlist elements
and one or more complete before the error is hit.
The error is rare enough though that my normal testing with server side
programs, such as nginx, httpd, envoy, etc., I have never seen this. The
only reliable way to reproduce that I've found is to stream movies over
my browser for a day or so and wait for it to hang. Not very scientific,
but with a few extra WARN_ON()s in the code the bug was obvious.
When we review the errors from copy_page_to_iter() it seems we are hitting
a page fault from copy_page_to_iter_iovec() where the code checks
fault_in_pages_writeable(buf, copy) where buf is the user buffer. It
also seems typical server applications don't hit this case.
The other way to try and reproduce this is run the sockmap selftest tool
test_sockmap with data verification enabled, but it doesn't reproduce the
fault. Perhaps we can trigger this case artificially somehow from the
test tools. I haven't sorted out a way to do that yet though.
Fixes: 604326b41a ("bpf, sockmap: convert to generic sk_msg interface")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/bpf/160556566659.73229.15694973114605301063.stgit@john-XPS-13-9370
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac3b57adf8 ]
If the clk_register fails, we should free h before
function returns to prevent memleak.
Fixes: 474402291a ("MIPS: Alchemy: clock framework integration of onchip clocks")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a584e9bc1b ]
There might be some requests pending in the buffer when the interface close
sequence occurs. In some devices, these pending requests might lead to the
module not shutting down properly when m_can_clk_stop() is called.
Therefore, move the device to init state before potentially powering it down.
Fixes: e0d1f4816f ("can: m_can: add Bosch M_CAN controller support")
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200825055442.16994-1-faiz_abbas@ti.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd0d83eab2 ]
m_can_handle_state_change() is called with the new_state as an argument.
In the switch statements for CAN_STATE_ERROR_ACTIVE, the comment and the
following code indicate that a CAN_STATE_ERROR_WARNING is handled.
This patch fixes this problem by changing the case to CAN_STATE_ERROR_WARNING.
Signed-off-by: Wu Bo <wubo.oduw@gmail.com>
Link: http://lore.kernel.org/r/20200129022330.21248-2-wubo.oduw@gmail.com
Cc: Dan Murphy <dmurphy@ti.com>
Fixes: e0d1f4816f ("can: m_can: add Bosch M_CAN controller support")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3fcce133f0 ]
regmap is a library function that gets selected by drivers that need it. No
driver modules should depend on it. Instead depends on SPI and select
REGMAP_SPI. Depending on REGMAP_SPI makes this driver only build if another
driver already selected REGMAP_SPI, as the symbol can't be selected through the
menu kernel configuration.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: http://lore.kernel.org/r/20200413141013.506613-1-enric.balletbo@collabora.com
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Fixes: 5443c226ba ("can: tcan4x5x: Add tcan4x5x driver to the kernel")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b7ee5bc3e1 ]
pm_runtime_get_sync() will increment pm usage at first and it will resume the
device later. If runtime of the device has error or device is in inaccessible
state(or other error state), resume operation will fail. If we do not call put
operation to decrease the reference, it will result in reference leak in the
two functions flexcan_get_berr_counter() and flexcan_open().
Moreover, this device cannot enter the idle state and always stay busy or other
non-idle state later. So we should fix it through adding
pm_runtime_put_noidle().
Fixes: ca10989632 ("can: flexcan: implement can Runtime PM")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201108083000.2599705-1-zhangqilong3@huawei.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a68cc0d69 ]
The left shift of int 32 bit integer constant 1 is evaluated using 32 bit
arithmetic and then assigned to a signed 64 bit variable. In the case where
time_ref->adapter->ts_used_bits is 32 or more this can lead to an oveflow.
Avoid this by shifting using the BIT_ULL macro instead.
Fixes: bb4785551f ("can: usb: PEAK-System Technik USB adapters driver core")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20201105112427.40688-1-colin.king@canonical.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9aa9379d8f ]
In canfd_rcv(), cfd->len is uninitialized when skb->len = 0, and this
uninitialized cfd->len is accessed nonetheless by pr_warn_once().
Fix this uninitialized variable access by checking cfd->len's validity
condition (cfd->len > CANFD_MAX_DLEN) separately after the skb->len's
condition is checked, and appropriately modify the log messages that
are generated as well.
In case either of the required conditions fail, the skb is freed and
NET_RX_DROP is returned, same as before.
Fixes: d468984688 ("can: af_can: canfd_rcv(): replace WARN_ONCE by pr_warn_once")
Reported-by: syzbot+9bcb0c9409066696d3aa@syzkaller.appspotmail.com
Tested-by: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Link: https://lore.kernel.org/r/20201103213906.24219-3-anant.thazhemadam@gmail.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8c958a58f ]
In can_rcv(), cfd->len is uninitialized when skb->len = 0, and this
uninitialized cfd->len is accessed nonetheless by pr_warn_once().
Fix this uninitialized variable access by checking cfd->len's validity
condition (cfd->len > CAN_MAX_DLEN) separately after the skb->len's
condition is checked, and appropriately modify the log messages that
are generated as well.
In case either of the required conditions fail, the skb is freed and
NET_RX_DROP is returned, same as before.
Fixes: 8cb68751c1 ("can: af_can: can_rcv(): replace WARN_ONCE by pr_warn_once")
Reported-by: syzbot+9bcb0c9409066696d3aa@syzkaller.appspotmail.com
Tested-by: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Link: https://lore.kernel.org/r/20201103213906.24219-2-anant.thazhemadam@gmail.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0e5a05cc9 ]
When execute command "perf lock report", it hits failure and outputs log
as follows:
perf: builtin-lock.c:623: report_lock_release_event: Assertion `!(seq->read_count < 0)' failed.
Aborted
This is an imbalance issue. The locking sequence structure
"lock_seq_stat" contains the reader counter and it is used to check if
the locking sequence is balance or not between acquiring and releasing.
If the tool wrongly frees "lock_seq_stat" when "read_count" isn't zero,
the "read_count" will be reset to zero when allocate a new structure at
the next time; thus it causes the wrong counting for reader and finally
results in imbalance issue.
To fix this issue, if detects "read_count" is not zero (means still have
read user in the locking sequence), goto the "end" tag to skip freeing
structure "lock_seq_stat".
Fixes: e4cef1f650 ("perf lock: Fix state machine to recognize lock sequence")
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Link: https://lore.kernel.org/r/20201104094229.17509-2-leo.yan@linaro.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1e678bf29 ]
dma_virt_ops requires that all pages have a kernel virtual address.
Introduce a INFINIBAND_VIRT_DMA Kconfig symbol that depends on !HIGHMEM
and make all three drivers depend on the new symbol.
Also remove the ARCH_DMA_ADDR_T_64BIT dependency, which has been obsolete
since commit 4965a68780 ("arch: define the ARCH_DMA_ADDR_T_64BIT config
symbol in lib/Kconfig")
Fixes: 551199aca1 ("lib/dma-virt: Add dma_virt_ops")
Link: https://lore.kernel.org/r/20201106181941.1878556-2-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 94e2bd0b25 ]
If a device is getting removed or reprobed during resume, use-after-free
might happen. For example, h5_btrtl_resume() schedules a work queue for
device reprobing, which of course requires removal first.
If the removal happens in parallel with the device_resume() and wins the
race to acquire device_lock(), removal may remove the device from the PM
lists and all, but device_resume() is already running and will continue
when the lock can be acquired, thus calling rfkill_resume().
During this, if rfkill_set_block() is then called after the corresponding
*_unregister() and kfree() are called, there will be an use-after-free
in hci_rfkill_set_block():
BUG: KASAN: use-after-free in hci_rfkill_set_block+0x58/0xc0 [bluetooth]
...
Call trace:
dump_backtrace+0x0/0x154
show_stack+0x20/0x2c
dump_stack+0xbc/0x12c
print_address_description+0x88/0x4b0
__kasan_report+0x144/0x168
kasan_report+0x10/0x18
check_memory_region+0x19c/0x1ac
__kasan_check_write+0x18/0x24
hci_rfkill_set_block+0x58/0xc0 [bluetooth]
rfkill_set_block+0x9c/0x120
rfkill_resume+0x34/0x70
dpm_run_callback+0xf0/0x1f4
device_resume+0x210/0x22c
Fix this by checking rfkill->registered in rfkill_resume(). device_del()
in rfkill_unregister() requires device_lock() and the whole rfkill_resume()
is also protected by the same lock via device_resume(), we can make sure
either the rfkill->registered is false before rfkill_resume() starts or the
rfkill device won't be unregistered before rfkill_resume() returns.
As async_resume() holds a reference to the device, at this level there can
be no use-after-free; only in the user that doesn't expect this scenario.
Fixes: 8589086f4e ("Bluetooth: hci_h5: Turn off RTL8723BS on suspend, reprobe on resume")
Signed-off-by: Claire Chang <tientzu@chromium.org>
Link: https://lore.kernel.org/r/20201110084908.219088-1-tientzu@chromium.org
[edit commit message for clarity and add more info provided later]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 676650d007 ]
When TOUCHSCREEN_ADC is enabled and IIO_BUFFER is disabled, it results
in the following Kbuild warning:
WARNING: unmet direct dependencies detected for IIO_BUFFER_CB
Depends on [n]: IIO [=y] && IIO_BUFFER [=n]
Selected by [y]:
- TOUCHSCREEN_ADC [=y] && !UML && INPUT [=y] && INPUT_TOUCHSCREEN [=y] && IIO [=y]
The reason is that TOUCHSCREEN_ADC selects IIO_BUFFER_CB without depending
on or selecting IIO_BUFFER while IIO_BUFFER_CB depends on IIO_BUFFER. This
can also fail building the kernel.
Honor the kconfig dependency to remove unmet direct dependency warnings
and avoid any potential build failures.
Fixes: aa132ffb6b ("input: touchscreen: resistive-adc-touch: add generic resistive ADC touchscreen")
Signed-off-by: Necip Fazil Yildiran <fazilyildiran@gmail.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20201102221504.541279-1-fazilyildiran@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 33d0d84387 ]
The SPI chip selects are represented as:
cs-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>, <&gpio4 13 GPIO_ACTIVE_LOW>;
, which means that they are used in GPIO function instead of native
SPI mode.
Fix the IOMUX for the chip select 1 to use GPIO4_13 instead of
the native CSPI_SSI function.
Fixes: c605cbf5e1 ("ARM: dts: imx: add device tree support for Freescale imx50evk board")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d19d2152ca ]
The datasheet for both the industrial and consumer variant of the
SoC lists a typical voltage of 0.95V for the 1.6GHz CPU operating
point.
Fixes: e85c9d0faa (arm64: dts: imx8mm: Add cpufreq properties)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f51778db08 ]
After merging the drm-misc tree, linux-next build (arm
multi_v7_defconfig) failed like this:
In file included from drivers/gpu/drm/nouveau/nouveau_ttm.c:26:
include/linux/swiotlb.h: In function 'swiotlb_max_mapping_size':
include/linux/swiotlb.h:99:9: error: 'SIZE_MAX' undeclared (first use in this function)
99 | return SIZE_MAX;
| ^~~~~~~~
include/linux/swiotlb.h:7:1: note: 'SIZE_MAX' is defined in header '<stdint.h>'; did you forget to '#include <stdint.h>'?
6 | #include <linux/init.h>
+++ |+#include <stdint.h>
7 | #include <linux/types.h>
include/linux/swiotlb.h:99:9: note: each undeclared identifier is reported only once for each function it appears in
99 | return SIZE_MAX;
| ^~~~~~~~
Caused by commit
abe420bfae ("swiotlb: Introduce swiotlb_max_mapping_size()")
but only exposed by commit "drm/nouveu: fix swiotlb include"
Fix it by including linux/limits.h as appropriate.
Fixes: abe420bfae ("swiotlb: Introduce swiotlb_max_mapping_size()")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20201102124327.2f82b2a7@canb.auug.org.au
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf5abb0132 ]
According to the i.MX8MN TRM, there is only one OTG port. The
address for OTG2 is reserved on Nano.
This patch removes the non-existent OTG2, usbphynop2, and the usbmisc2
nodes.
Fixes: 6c3debcbae ("arm64: dts: freescale: Add i.MX8MN dtsi support")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a9a8910b2 ]
The Ethernet PHY on the Bananapi M64 has the RX and TX delays
enabled on the PHY, using pull-ups on the RXDLY and TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: e729549990 ("arm64: allwinner: bananapi-m64: Enable dwmac-sun8i")
Fixes: 94f4428867 ("arm64: dts: allwinner: A64: Restore EMAC changes")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201024162515.30032-10-wens@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3914160ffc ]
The Ethernet PHY on the Bananapi M2+ has the RX and TX delays
enabled on the PHY, using pull-ups on the RXDLY and TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: 8c7ba536e7 ("ARM: sun8i: bananapi-m2-plus: Enable dwmac-sun8i")
Fixes: 4904337fe3 ("ARM: dts: sunxi: Restore EMAC changes (boards)")
Fixes: aa8fee415f ("ARM: dts: sun8i: h3: Split out non-SoC-specific parts of Bananapi M2 Plus")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201024162515.30032-8-wens@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1064037e8 ]
The Ethernet PHY on the Cubieboard 4 and A80 Optimus have the RX
and TX delays enabled on the PHY, using pull-ups on the RXDLY and
TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: 98048143b7 ("ARM: dts: sun9i: cubieboard4: Enable GMAC")
Fixes: bc9bd03a44 ("ARM: dts: sun9i: a80-optimus: Enable GMAC")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201024162515.30032-7-wens@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 57dbe55845 ]
The Ethernet PHY on the Bananapi M3 and Cubietruck Plus have the RX
and TX delays enabled on the PHY, using pull-ups on the RXDLY and
TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: 039359948a ("ARM: dts: sun8i: a83t: Enable Ethernet on two boards")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201024162515.30032-6-wens@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e080ab31a0 ]
The Ethernet PHY on the Orange Pi Plus 2E has the RX and TX delays
enabled on the PHY, using pull-ups on the RXDLY and TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: 4904337fe3 ("ARM: dts: sunxi: Restore EMAC changes (boards)")
Fixes: 7a78ef92cd ("ARM: sun8i: h3: Enable EMAC with external PHY on Orange Pi Plus 2E")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201024162515.30032-5-wens@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f94f78bd93 ]
The Ethernet PHY on the Bananapi M1+ has the RX and TX delays
enabled on the PHY, using pull-ups on the RXDLY and TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: 04c85ecad3 ("ARM: dts: sun7i: Add dts file for Bananapi M1 Plus board")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201024162515.30032-4-wens@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 353c3de130 ]
The Ethernet PHY on the Cubietruck has the RX and TX delays
enabled on the PHY, using pull-ups on the RXDLY and TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: 67073d9767 ("ARM: dts: sun7i: cubietruck: Enable the GMAC")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Emilio López <emilio@elopez.com.ar>
Reviewed-by: Emilio López <emilio@elopez.com.ar>
Link: https://lore.kernel.org/r/20201024162515.30032-3-wens@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e76724153f ]
The Ethernet PHY on the A31 Hummingbird has the RX and TX delays
enabled on the PHY, using pull-ups on the RXDLY and TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: c220aec2bb ("ARM: dts: sun6i: Add Merrii A31 Hummingbird support")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201024162515.30032-2-wens@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 927f42fcc1 ]
According to board schematic, PHY provides both, RX and TX delays.
However, according to "fix" Realtek provided for this board, only TX
delay should be provided by PHY.
Tests show that both variants work but TX only PHY delay works
slightly better.
Update ethernet node to reflect the fact that PHY provides TX delay.
Fixes: 94f4428867 ("arm64: dts: allwinner: A64: Restore EMAC changes")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201022211301.3548422-1-jernej.skrabec@siol.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 97a38c1c21 ]
Before the commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e rx/tx
delay config"), the software overwrite for RX/TX delays of the RTL8211e
were not working properly and the Beelink GS1 had both RX/TX delay of RGMII
interface set using pull-up on the TXDLY and RXDLY pins.
Now that these delays are working properly they overwrite the HW
config and set this to 'rgmii' meaning no delay on both RX/TX.
This makes the ethernet of this board not working anymore.
Set the phy-mode to 'rgmii-id' meaning RGMII with RX/TX delays
in the device-tree to keep the correct configuration.
Fixes: 089bee8dd1 ("arm64: dts: allwinner: h6: Introduce Beelink GS1 board")
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20201018172409.1754775-1-peron.clem@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd8feec665 ]
To convert the number of pulses counted into an RPM estimation, we need
to divide by the width of our measurement interval instead of
multiplying by it. If the width of the measurement interval is zero we
don't update the RPM value to avoid dividing by zero.
We also don't need to do 64-bit division, with 32-bits we can handle a
fan running at over 4 million RPM.
Signed-off-by: Paul Barker <pbarker@konsulko.com>
Link: https://lore.kernel.org/r/20201111164643.7087-1-pbarker@konsulko.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc923818b1 ]
In the fail path of gfs2_check_blk_type, forgetting to call
gfs2_glock_dq_uninit will result in rgd_gh reference leak.
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 22843291ef ]
__sb_start_write has some weird looking lockdep code that claims to
exist to handle nested freeze locking requests from xfs. The code as
written seems broken -- if we think we hold a read lock on any of the
higher freeze levels (e.g. we hold SB_FREEZE_WRITE and are trying to
lock SB_FREEZE_PAGEFAULT), it converts a blocking lock attempt into a
trylock.
However, it's not correct to downgrade a blocking lock attempt to a
trylock unless the downgrading code or the callers are prepared to deal
with that situation. Neither __sb_start_write nor its callers handle
this at all. For example:
sb_start_pagefault ignores the return value completely, with the result
that if xfs_filemap_fault loses a race with a different thread trying to
fsfreeze, it will proceed without pagefault freeze protection (thereby
breaking locking rules) and then unlocks the pagefault freeze lock that
it doesn't own on its way out (thereby corrupting the lock state), which
leads to a system hang shortly afterwards.
Normally, this won't happen because our ownership of a read lock on a
higher freeze protection level blocks fsfreeze from grabbing a write
lock on that higher level. *However*, if lockdep is offline,
lock_is_held_type unconditionally returns 1, which means that
percpu_rwsem_is_held returns 1, which means that __sb_start_write
unconditionally converts blocking freeze lock attempts into trylocks,
even when we *don't* hold anything that would block a fsfreeze.
Apparently this all held together until 5.10-rc1, when bugs in lockdep
caused lockdep to shut itself off early in an fstests run, and once
fstests gets to the "race writes with freezer" tests, kaboom. This
might explain the long trail of vanishingly infrequent livelocks in
fstests after lockdep goes offline that I've never been able to
diagnose.
We could fix it by spinning on the trylock if wait==true, but AFAICT the
locking works fine if lockdep is not built at all (and I didn't see any
complaints running fstests overnight), so remove this snippet entirely.
NOTE: Commit f4b554af99 in 2015 created the current weird logic (which
used to exist in a different form in commit 5accdf82ba from 2012) in
__sb_start_write. XFS solved this whole problem in the late 2.6 era by
creating a variant of transactions (XFS_TRANS_NO_WRITECOUNT) that don't
grab intwrite freeze protection, thus making lockdep's solution
unnecessary. The commit claims that Dave Chinner explained that the
trylock hack + comment could be removed, but nobody ever did.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04e613ded8 ]
Commit ce3d31ad3c ("arm64/smp: Move rcu_cpu_starting() earlier") ensured
that RCU is informed early about incoming CPUs that might end up calling
into printk() before they are online. However, if such a CPU fails the
early CPU feature compatibility checks in check_local_cpu_capabilities(),
then it will be powered off or parked without informing RCU, leading to
an endless stream of stalls:
| rcu: INFO: rcu_preempt detected stalls on CPUs/tasks:
| rcu: 2-O...: (0 ticks this GP) idle=002/1/0x4000000000000000 softirq=0/0 fqs=2593
| (detected by 0, t=5252 jiffies, g=9317, q=136)
| Task dump for CPU 2:
| task:swapper/2 state:R running task stack: 0 pid: 0 ppid: 1 flags:0x00000028
| Call trace:
| ret_from_fork+0x0/0x30
Ensure that the dying CPU invokes rcu_report_dead() prior to being powered
off or parked.
Cc: Qian Cai <cai@redhat.com>
Cc: "Paul E. McKenney" <paulmck@kernel.org>
Reviewed-by: Paul E. McKenney <paulmck@kernel.org>
Suggested-by: Qian Cai <cai@redhat.com>
Link: https://lore.kernel.org/r/20201105222242.GA8842@willie-the-truck
Link: https://lore.kernel.org/r/20201106103602.9849-3-will@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7daaa06357 ]
The Medion Akoya E2228T's ACPI _LID implementation is quite broken,
it has the same issues as the one from the Medion Akoya E2215T:
1. For notifications it uses an ActiveLow Edge GpioInt, rather then
an ActiveBoth one, meaning that the device is only notified when the
lid is closed, not when it is opened.
2. Matching with this its _LID method simply always returns 0 (closed)
In order for the Linux LID code to work properly with this implementation,
the lid_init_state selection needs to be set to ACPI_BUTTON_LID_INIT_OPEN,
add a DMI quirk for this.
While working on this I also found out that the MD60### part of the model
number differs per country/batch while all of the E2215T and E2228T models
have this issue, so also remove the " MD60198" part from the E2215T quirk.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df11f7dd58 ]
Fix the layout of 'struct desc64' to match the layout described in the
SDM Vol 3, Chapter 3 "Protected-Mode Memory Management", section 3.4.5
"Segment Descriptors", Figure 3-8 "Segment Descriptor". The test added
later in this series relies on this and crashes if this layout is not
correct.
Signed-off-by: Aaron Lewis <aaronlewis@google.com>
Reviewed-by: Alexander Graf <graf@amazon.com>
Message-Id: <20201012194716.3950330-2-aaronlewis@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d5179458d ]
When removing the driver we would hit BUG_ON(!list_empty(&dev->ptype_specific))
in net/core/dev.c due to still having the NC-SI packet handler
registered.
# echo 1e660000.ethernet > /sys/bus/platform/drivers/ftgmac100/unbind
------------[ cut here ]------------
kernel BUG at net/core/dev.c:10254!
Internal error: Oops - BUG: 0 [#1] SMP ARM
CPU: 0 PID: 115 Comm: sh Not tainted 5.10.0-rc3-next-20201111-00007-g02e0365710c4 #46
Hardware name: Generic DT based system
PC is at netdev_run_todo+0x314/0x394
LR is at cpumask_next+0x20/0x24
pc : [<806f5830>] lr : [<80863cb0>] psr: 80000153
sp : 855bbd58 ip : 00000001 fp : 855bbdac
r10: 80c03d00 r9 : 80c06228 r8 : 81158c54
r7 : 00000000 r6 : 80c05dec r5 : 80c05d18 r4 : 813b9280
r3 : 813b9054 r2 : 8122c470 r1 : 00000002 r0 : 00000002
Flags: Nzcv IRQs on FIQs off Mode SVC_32 ISA ARM Segment none
Control: 00c5387d Table: 85514008 DAC: 00000051
Process sh (pid: 115, stack limit = 0x7cb5703d)
...
Backtrace:
[<806f551c>] (netdev_run_todo) from [<80707eec>] (rtnl_unlock+0x18/0x1c)
r10:00000051 r9:854ed710 r8:81158c54 r7:80c76bb0 r6:81158c10 r5:8115b410
r4:813b9000
[<80707ed4>] (rtnl_unlock) from [<806f5db8>] (unregister_netdev+0x2c/0x30)
[<806f5d8c>] (unregister_netdev) from [<805a8180>] (ftgmac100_remove+0x20/0xa8)
r5:8115b410 r4:813b9000
[<805a8160>] (ftgmac100_remove) from [<805355e4>] (platform_drv_remove+0x34/0x4c)
Fixes: bd466c3fb5 ("net/faraday: Support NCSI mode")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20201117024448.1170761-1-joel@jms.id.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1922a46b8c ]
If a user unbinds and re-binds a NC-SI aware driver the kernel will
attempt to register the netlink interface at runtime. The structure is
marked __ro_after_init so registration fails spectacularly at this point.
# echo 1e660000.ethernet > /sys/bus/platform/drivers/ftgmac100/unbind
# echo 1e660000.ethernet > /sys/bus/platform/drivers/ftgmac100/bind
ftgmac100 1e660000.ethernet: Read MAC address 52:54:00:12:34:56 from chip
ftgmac100 1e660000.ethernet: Using NCSI interface
8<--- cut here ---
Unable to handle kernel paging request at virtual address 80a8f858
pgd = 8c768dd6
[80a8f858] *pgd=80a0841e(bad)
Internal error: Oops: 80d [#1] SMP ARM
CPU: 0 PID: 116 Comm: sh Not tainted 5.10.0-rc3-next-20201111-00003-gdd25b227ec1e #51
Hardware name: Generic DT based system
PC is at genl_register_family+0x1f8/0x6d4
LR is at 0xff26ffff
pc : [<8073f930>] lr : [<ff26ffff>] psr: 20000153
sp : 8553bc80 ip : 81406244 fp : 8553bd04
r10: 8085d12c r9 : 80a8f73c r8 : 85739000
r7 : 00000017 r6 : 80a8f860 r5 : 80c8ab98 r4 : 80a8f858
r3 : 00000000 r2 : 00000000 r1 : 81406130 r0 : 00000017
Flags: nzCv IRQs on FIQs off Mode SVC_32 ISA ARM Segment none
Control: 00c5387d Table: 85524008 DAC: 00000051
Process sh (pid: 116, stack limit = 0x1f1988d6)
...
Backtrace:
[<8073f738>] (genl_register_family) from [<80860ac0>] (ncsi_init_netlink+0x20/0x48)
r10:8085d12c r9:80c8fb0c r8:85739000 r7:00000000 r6:81218000 r5:85739000
r4:8121c000
[<80860aa0>] (ncsi_init_netlink) from [<8085d740>] (ncsi_register_dev+0x1b0/0x210)
r5:8121c400 r4:8121c000
[<8085d590>] (ncsi_register_dev) from [<805a8060>] (ftgmac100_probe+0x6e0/0x778)
r10:00000004 r9:80950228 r8:8115bc10 r7:8115ab00 r6:9eae2c24 r5:813b6f88
r4:85739000
[<805a7980>] (ftgmac100_probe) from [<805355ec>] (platform_drv_probe+0x58/0xa8)
r9:80c76bb0 r8:00000000 r7:80cd4974 r6:80c76bb0 r5:8115bc10 r4:00000000
[<80535594>] (platform_drv_probe) from [<80532d58>] (really_probe+0x204/0x514)
r7:80cd4974 r6:00000000 r5:80cd4868 r4:8115bc10
Jakub pointed out that ncsi_register_dev is obviously broken, because
there is only one family so it would never work if there was more than
one ncsi netdev.
Fix the crash by registering the netlink family once on boot, and drop
the code to unregister it.
Fixes: 955dc68cb9 ("net/ncsi: Add generic netlink family")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Link: https://lore.kernel.org/r/20201112061210.914621-1-joel@jms.id.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 470b747582 ]
Currently when QoS is enabled for VF and any min_rate is configured,
the driver sets bw_share value to at least 1 and doesn’t allow to set
it to 0 to make minimal rate unlimited. It means there is always a
minimal rate configured for every VF, even if user tries to remove it.
In order to make QoS disable possible, check whether all vports have
configured min_rate = 0. If this is true, set their bw_share to 0 to
disable min_rate limitations.
Fixes: c9497c9890 ("net/mlx5: Add support for setting VF min rate")
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1b9e2a8c99 ]
During loss recovery, retransmitted packets are forced to use TCP
timestamps to calculate the RTT samples, which have a millisecond
granularity. BBR is designed using a microsecond granularity. As a
result, multiple RTT samples could be truncated to the same RTT value
during loss recovery. This is problematic, as BBR will not enter
PROBE_RTT if the RTT sample is <= the current min_rtt sample, meaning
that if there are persistent losses, PROBE_RTT will constantly be
pushed off and potentially never re-entered. This patch makes sure
that BBR enters PROBE_RTT by checking if RTT sample is < the current
min_rtt sample, rather than <=.
The Netflix transport/TCP team discovered this bug in the Linux TCP
BBR code during lab tests.
Fixes: 0f8782ea14 ("tcp_bbr: add BBR congestion control")
Signed-off-by: Ryan Sharpelletti <sharpelletti@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Link: https://lore.kernel.org/r/20201116174412.1433277-1-sharpelletti.kdev@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 057a10fa1f ]
A call trace was found in Hangbin's Codenomicon testing with debug kernel:
[ 2615.981988] ODEBUG: free active (active state 0) object type: timer_list hint: sctp_generate_proto_unreach_event+0x0/0x3a0 [sctp]
[ 2615.995050] WARNING: CPU: 17 PID: 0 at lib/debugobjects.c:328 debug_print_object+0x199/0x2b0
[ 2616.095934] RIP: 0010:debug_print_object+0x199/0x2b0
[ 2616.191533] Call Trace:
[ 2616.194265] <IRQ>
[ 2616.202068] debug_check_no_obj_freed+0x25e/0x3f0
[ 2616.207336] slab_free_freelist_hook+0xeb/0x140
[ 2616.220971] kfree+0xd6/0x2c0
[ 2616.224293] rcu_do_batch+0x3bd/0xc70
[ 2616.243096] rcu_core+0x8b9/0xd00
[ 2616.256065] __do_softirq+0x23d/0xacd
[ 2616.260166] irq_exit+0x236/0x2a0
[ 2616.263879] smp_apic_timer_interrupt+0x18d/0x620
[ 2616.269138] apic_timer_interrupt+0xf/0x20
[ 2616.273711] </IRQ>
This is because it holds asoc when transport->proto_unreach_timer starts
and puts asoc when the timer stops, and without holding transport the
transport could be freed when the timer is still running.
So fix it by holding/putting transport instead for proto_unreach_timer
in transport, just like other timers in transport.
v1->v2:
- Also use sctp_transport_put() for the "out_unlock:" path in
sctp_generate_proto_unreach_event(), as Marcelo noticed.
Fixes: 50b5d6ad63 ("sctp: Fix a race between ICMP protocol unreachable and connect()")
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Link: https://lore.kernel.org/r/102788809b554958b13b95d33440f5448113b8d6.1605331373.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d8c19014bb ]
The ethernet driver may allocate skb (and skb->data) via napi_alloc_skb().
This ends up to page_frag_alloc() to allocate skb->data from
page_frag_cache->va.
During the memory pressure, page_frag_cache->va may be allocated as
pfmemalloc page. As a result, the skb->pfmemalloc is always true as
skb->data is from page_frag_cache->va. The skb will be dropped if the
sock (receiver) does not have SOCK_MEMALLOC. This is expected behaviour
under memory pressure.
However, once kernel is not under memory pressure any longer (suppose large
amount of memory pages are just reclaimed), the page_frag_alloc() may still
re-use the prior pfmemalloc page_frag_cache->va to allocate skb->data. As a
result, the skb->pfmemalloc is always true unless page_frag_cache->va is
re-allocated, even if the kernel is not under memory pressure any longer.
Here is how kernel runs into issue.
1. The kernel is under memory pressure and allocation of
PAGE_FRAG_CACHE_MAX_ORDER in __page_frag_cache_refill() will fail. Instead,
the pfmemalloc page is allocated for page_frag_cache->va.
2: All skb->data from page_frag_cache->va (pfmemalloc) will have
skb->pfmemalloc=true. The skb will always be dropped by sock without
SOCK_MEMALLOC. This is an expected behaviour.
3. Suppose a large amount of pages are reclaimed and kernel is not under
memory pressure any longer. We expect skb->pfmemalloc drop will not happen.
4. Unfortunately, page_frag_alloc() does not proactively re-allocate
page_frag_alloc->va and will always re-use the prior pfmemalloc page. The
skb->pfmemalloc is always true even kernel is not under memory pressure any
longer.
Fix this by freeing and re-allocating the page instead of recycling it.
References: https://lore.kernel.org/lkml/20201103193239.1807-1-dongli.zhang@oracle.com/
References: https://lore.kernel.org/linux-mm/20201105042140.5253-1-willy@infradead.org/
Suggested-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Aruna Ramakrishna <aruna.ramakrishna@oracle.com>
Cc: Bert Barbe <bert.barbe@oracle.com>
Cc: Rama Nichanamatlu <rama.nichanamatlu@oracle.com>
Cc: Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com>
Cc: Manjunath Patil <manjunath.b.patil@oracle.com>
Cc: Joe Jin <joe.jin@oracle.com>
Cc: SRINIVAS <srinivas.eeda@oracle.com>
Fixes: 79930f5892 ("net: do not deplete pfmemalloc reserve")
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20201115201029.11903-1-dongli.zhang@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4ee18c179e ]
The x25_disconnect function in x25_subr.c would decrease the refcount of
"x25->neighbour" (struct x25_neigh) and reset this pointer to NULL.
However, the x25_rx_call_request function in af_x25.c, which is called
when we receive a connection request, does not increase the refcount when
it assigns the pointer.
Fix this issue by increasing the refcount of "struct x25_neigh" in
x25_rx_call_request.
This patch fixes frequent kernel crashes when using AF_X25 sockets.
Fixes: 4becb7ee5b ("net/x25: Fix x25_neigh refcnt leak when x25 disconnect")
Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Link: https://lore.kernel.org/r/20201112103506.5875-1-xie.he.0141@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3fe16edf67 ]
If tcp socket has more data than Encrypted Handshake Message then
tls_sw_recvmsg will try to decrypt next record instead of returning
full control message to userspace as mentioned in comment. The next
message - usually Application Data - gets corrupted because it uses
zero copy for decryption that's why the data is not stored in skb
for next iteration. Revert check to not decrypt next record if
current is not Application Data.
Fixes: 692d7b5d1f ("tls: Fix recvmsg() to be able to peek across multiple records")
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Link: https://lore.kernel.org/r/1605413760-21153-1-git-send-email-vfedorenko@novek.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fc70f5bf5e ]
During rmnet unregistration, the real device rx_handler is first cleared
followed by the removal of rx_handler_data after the rcu synchronization.
Any packets in the receive path may observe that the rx_handler is NULL.
However, there is no check when dereferencing this value to use the
rmnet_port information.
This fixes following splat by adding the NULL check.
Unable to handle kernel NULL pointer dereference at virtual
address 000000000000000d
pc : rmnet_rx_handler+0x124/0x284
lr : rmnet_rx_handler+0x124/0x284
rmnet_rx_handler+0x124/0x284
__netif_receive_skb_core+0x758/0xd74
__netif_receive_skb+0x50/0x17c
process_backlog+0x15c/0x1b8
napi_poll+0x88/0x284
net_rx_action+0xbc/0x23c
__do_softirq+0x20c/0x48c
Fixes: ceed73a2cf ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Link: https://lore.kernel.org/r/1605298325-3705-1-git-send-email-subashab@codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6d9c8d15af ]
Slave function read the following capabilities from the wrong offset:
1. log_mc_entry_sz
2. fs_log_entry_sz
3. log_mc_hash_sz
Fix that by adjusting these capabilities offset to match firmware
layout.
Due to the wrong offset read, the following issues might occur:
1+2. Negative value reported at max_mcast_qp_attach.
3. Driver to init FW with multicast hash size of zero.
Fixes: a40ded6043 ("net/mlx4_core: Add masking for a few queries on HCA caps")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Eran Ben Elisha <eranbe@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20201118081922.553-1-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2a1828e378 ]
A user reports (slightly shortened from the original message):
libphy: lantiq,xrx200-mdio: probed
mdio_bus 1e108000.switch-mii: MDIO device at address 17 is missing.
gswip 1e108000.switch lan: no phy at 2
gswip 1e108000.switch lan: failed to connect to port 2: -19
lantiq,xrx200-net 1e10b308.eth eth0: error -19 setting up slave phy
This is a single-port board using the internal Fast Ethernet PHY. The
user reports that switching to PHY scanning instead of configuring the
PHY within device-tree works around this issue.
The documentation for the standalone variant of the PHY11G (which is
probably very similar to what is used inside the xRX200 SoCs but having
the firmware burnt onto that standalone chip in the factory) states that
the PHY needs 300ms to be ready for MDIO communication after releasing
the reset.
Add a 300ms delay after initializing all GPHYs to ensure that the GPHY
firmware had enough time to initialize and to appear on the MDIO bus.
Unfortunately there is no (known) documentation on what the minimum time
to wait after releasing the reset on an internal PHY so play safe and
take the one for the external variant. Only wait after the last GPHY
firmware is loaded to not slow down the initialization too much (
xRX200 has two GPHYs but newer SoCs have at least three GPHYs).
Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20201115165757.552641-1-martin.blumenstingl@googlemail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 866358ec33 ]
The current NetLabel code doesn't correctly keep track of the netlink
dump state in some cases, in particular when multiple interfaces with
large configurations are loaded. The problem manifests itself by not
reporting the full configuration to userspace, even though it is
loaded and active in the kernel. This patch fixes this by ensuring
that the dump state is properly reset when necessary inside the
netlbl_unlabel_staticlist() function.
Fixes: 8cc44579d1 ("NetLabel: Introduce static network labels for unlabeled connections")
Signed-off-by: Paul Moore <paul@paul-moore.com>
Link: https://lore.kernel.org/r/160484450633.3752.16512718263560813473.stgit@sifl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1532b97784 ]
DSA network devices rely on having their DSA management interface up and
running otherwise their ndo_open() will return -ENETDOWN. Without doing
this it would not be possible to use DSA devices as netconsole when
configured on the command line. These devices also do not utilize the
upper/lower linking so the check about the netpoll device having upper
is not going to be a problem.
The solution adopted here is identical to the one done for
net/ipv4/ipconfig.c with 728c02089a ("net: ipv4: handle DSA enabled
master network devices"), with the network namespace scope being
restricted to that of the process configuring netpoll.
Fixes: 04ff53f96a ("net: dsa: Add netconsole support")
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20201117035236.22658-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 92307069a9 ]
As soon as you add the second port to a VLAN, all other port
membership configuration is overwritten with zeroes. The HW interprets
this as all ports being "unmodified members" of the VLAN.
In the simple case when all ports belong to the same VLAN, switching
will still work. But using multiple VLANs or trying to set multiple
ports as tagged members will not work.
On the 6352, doing a VTU GetNext op, followed by an STU GetNext op
will leave you with both the member- and state- data in the VTU/STU
data registers. But on the 6097 (which uses the same implementation),
the STU GetNext will override the information gathered from the VTU
GetNext.
Separate the two stages, parsing the result of the VTU GetNext before
doing the STU GetNext.
We opt to update the existing implementation for all applicable chips,
as opposed to creating a separate callback for 6097, because although
the previous implementation did work for (at least) 6352, the
datasheet does not mention the masking behavior.
Fixes: ef6fcea37f ("net: dsa: mv88e6xxx: get STU entry on VTU GetNext")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Link: https://lore.kernel.org/r/20201112114335.27371-1-tobias@waldekranz.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1f492eab67 ]
The driver sends Ethernet Management Datagram (EMAD) packets to the
device for configuration purposes and waits for up to 200ms for a reply.
A request is retried up to 5 times.
When the system is under heavy load, replies are not always processed in
time and EMAD transactions fail.
Make the process more robust to such delays by using exponential
backoff. First wait for up to 200ms, then retransmit and wait for up to
400ms and so on.
Fixes: caf7297e7a ("mlxsw: core: Introduce support for asynchronous EMAD register access")
Reported-by: Denis Yulevich <denisyu@nvidia.com>
Tested-by: Denis Yulevich <denisyu@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 796a2665ca ]
On arm imx6, when opening the chip's netdev, the whole Linux
kernel intermittently hangs/freezes.
This is caused by a bug in the driver code which tests if pcie
interrupts are working correctly, using the software interrupt:
1. open: enable the software interrupt
2. open: tell the chip to assert the software interrupt
3. open: wait for flag
4. ISR: acknowledge s/w interrupt, set flag
5. open: notice flag, disable the s/w interrupt, continue
Unfortunately the ISR only acknowledges the s/w interrupt, but
does not disable it. This will re-trigger the ISR in a tight
loop.
On some (lucky) platforms, open proceeds to disable the s/w
interrupt even while the ISR is 'spinning'. On arm imx6,
the spinning ISR does not allow open to proceed, resulting
in a hung Linux kernel.
Fix minimally by disabling the s/w interrupt in the ISR, which
will prevent it from spinning. This won't break anything because
the s/w interrupt is used as a one-shot interrupt.
Note that this is a minimal fix, overlooking many possible
cleanups, e.g.:
- lan743x_intr_software_isr() is completely redundant and reads
INT_STS twice for no apparent reason
- disabling the s/w interrupt in lan743x_intr_test_isr() is now
redundant, but harmless
- waiting on software_isr_flag can be converted from a sleeping
poll loop to wait_event_timeout()
Fixes: 23f0703c12 ("lan743x: Add main source files for new lan743x driver")
Tested-by: Sven Van Asbroeck <thesven73@gmail.com> # arm imx6 lan7430
Signed-off-by: Sven Van Asbroeck <thesven73@gmail.com>
Link: https://lore.kernel.org/r/20201112204741.12375-1-TheSven73@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e35df62e04 ]
When running this chip on arm imx6, we intermittently observe
the following kernel warning in the log, especially when the
system is under high load:
[ 50.119484] ------------[ cut here ]------------
[ 50.124377] WARNING: CPU: 0 PID: 303 at kernel/softirq.c:169 __local_bh_enable_ip+0x100/0x184
[ 50.132925] IRQs not enabled as expected
[ 50.159250] CPU: 0 PID: 303 Comm: rngd Not tainted 5.7.8 #1
[ 50.164837] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
[ 50.171395] [<c0111a38>] (unwind_backtrace) from [<c010be28>] (show_stack+0x10/0x14)
[ 50.179162] [<c010be28>] (show_stack) from [<c05b9dec>] (dump_stack+0xac/0xd8)
[ 50.186408] [<c05b9dec>] (dump_stack) from [<c0122e40>] (__warn+0xd0/0x10c)
[ 50.193391] [<c0122e40>] (__warn) from [<c0123238>] (warn_slowpath_fmt+0x98/0xc4)
[ 50.200892] [<c0123238>] (warn_slowpath_fmt) from [<c012b010>] (__local_bh_enable_ip+0x100/0x184)
[ 50.209860] [<c012b010>] (__local_bh_enable_ip) from [<bf09ecbc>] (destroy_conntrack+0x48/0xd8 [nf_conntrack])
[ 50.220038] [<bf09ecbc>] (destroy_conntrack [nf_conntrack]) from [<c0ac9b58>] (nf_conntrack_destroy+0x94/0x168)
[ 50.230160] [<c0ac9b58>] (nf_conntrack_destroy) from [<c0a4aaa0>] (skb_release_head_state+0xa0/0xd0)
[ 50.239314] [<c0a4aaa0>] (skb_release_head_state) from [<c0a4aadc>] (skb_release_all+0xc/0x24)
[ 50.247946] [<c0a4aadc>] (skb_release_all) from [<c0a4b4cc>] (consume_skb+0x74/0x17c)
[ 50.255796] [<c0a4b4cc>] (consume_skb) from [<c081a2dc>] (lan743x_tx_release_desc+0x120/0x124)
[ 50.264428] [<c081a2dc>] (lan743x_tx_release_desc) from [<c081a98c>] (lan743x_tx_napi_poll+0x5c/0x18c)
[ 50.273755] [<c081a98c>] (lan743x_tx_napi_poll) from [<c0a6b050>] (net_rx_action+0x118/0x4a4)
[ 50.282306] [<c0a6b050>] (net_rx_action) from [<c0101364>] (__do_softirq+0x13c/0x53c)
[ 50.290157] [<c0101364>] (__do_softirq) from [<c012b29c>] (irq_exit+0x150/0x17c)
[ 50.297575] [<c012b29c>] (irq_exit) from [<c0196a08>] (__handle_domain_irq+0x60/0xb0)
[ 50.305423] [<c0196a08>] (__handle_domain_irq) from [<c05d44fc>] (gic_handle_irq+0x4c/0x90)
[ 50.313790] [<c05d44fc>] (gic_handle_irq) from [<c0100ed4>] (__irq_usr+0x54/0x80)
[ 50.321287] Exception stack(0xecd99fb0 to 0xecd99ff8)
[ 50.326355] 9fa0: 1cf1aa74 00000001 00000001 00000000
[ 50.334547] 9fc0: 00000001 00000000 00000000 00000000 00000000 00000000 00004097 b6d17d14
[ 50.342738] 9fe0: 00000001 b6d17c60 00000000 b6e71f94 800b0010 ffffffff
[ 50.349364] irq event stamp: 2525027
[ 50.352955] hardirqs last enabled at (2525026): [<c0a6afec>] net_rx_action+0xb4/0x4a4
[ 50.360892] hardirqs last disabled at (2525027): [<c0d6d2fc>] _raw_spin_lock_irqsave+0x1c/0x50
[ 50.369517] softirqs last enabled at (2524660): [<c01015b4>] __do_softirq+0x38c/0x53c
[ 50.377446] softirqs last disabled at (2524693): [<c012b29c>] irq_exit+0x150/0x17c
[ 50.385027] ---[ end trace c0b571db4bc8087d ]---
The driver is calling dev_kfree_skb() from code inside a spinlock,
where h/w interrupts are disabled. This is forbidden, as documented
in include/linux/netdevice.h. The correct function to use
dev_kfree_skb_irq(), or dev_kfree_skb_any().
Fix by using the correct dev_kfree_skb_xxx() functions:
in lan743x_tx_release_desc():
called by lan743x_tx_release_completed_descriptors()
called by in lan743x_tx_napi_poll()
which holds a spinlock
called by lan743x_tx_release_all_descriptors()
called by lan743x_tx_close()
which can-sleep
conclusion: use dev_kfree_skb_any()
in lan743x_tx_xmit_frame():
which holds a spinlock
conclusion: use dev_kfree_skb_irq()
in lan743x_tx_close():
which can-sleep
conclusion: use dev_kfree_skb()
in lan743x_rx_release_ring_element():
called by lan743x_rx_close()
which can-sleep
called by lan743x_rx_open()
which can-sleep
conclusion: use dev_kfree_skb()
Fixes: 23f0703c12 ("lan743x: Add main source files for new lan743x driver")
Signed-off-by: Sven Van Asbroeck <thesven73@gmail.com>
Link: https://lore.kernel.org/r/20201112185949.11315-1-TheSven73@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8cf8821e15 ]
Commit 58956317c8 ("neighbor: Improve garbage collection")
guarantees neighbour table entries a five-second lifetime. Processes
which make heavy use of multicast can fill the neighour table with
multicast addresses in five seconds. At that point, neighbour entries
can't be GC-ed because they aren't five seconds old yet, the kernel
log starts to fill up with "neighbor table overflow!" messages, and
sends start to fail.
This patch allows multicast addresses to be thrown out before they've
lived out their five seconds. This makes room for non-multicast
addresses and makes messages to all addresses more reliable in these
circumstances.
Fixes: 58956317c8 ("neighbor: Improve garbage collection")
Signed-off-by: Jeff Dike <jdike@akamai.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20201113015815.31397-1-jdike@akamai.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4260330b32 ]
The module eeprom address range returned by bnxt_get_module_eeprom()
should be 256 bytes of A0h address space, the lower half of the A2h
address space, and page 0 for the upper half of the A2h address space.
Fix the firmware call by passing page_number 0 for the A2h slave address
space.
Fixes: 42ee18fe4c ("bnxt_en: Add Support for ETHTOOL_GMODULEINFO and ETHTOOL_GMODULEEEPRO")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6dceaa9f56 ]
The `skb' is mapped for DMA in ns_send() but does not unmap DMA in case
push_scqe() fails to submit the `skb'. The memory of the `skb' is
released so only the DMA mapping is leaking.
Unmap the DMA mapping in case push_scqe() failed.
Fixes: 864a3ff635 ("atm: [nicstar] remove virt_to_bus() and support 64-bit platforms")
Cc: Chas Williams <3chas3@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
