It is important to reinitialise the firmware array pointers to protect
against the case that the brcmfmac driver is reprobed without first
being unloaded.
The potential hazard was noticed while investigating
https://github.com/raspberrypi/firmware/issues/1644 .
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Add the ability to load the names of alternative firmwares from the
Device Tree node. This permits separate firmwares for 43436s and 43438
and allows downstream firmwares to coexist with upstream.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
This reverts commit c52581ffa4.
Replace the hardcoded alternate firmware names with mappings provided
from Device Tree.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
BCM43430/2 may be BCM43430B0 or BCM43436P, and BCM43430/1 can be either
BCM43430A1 or BCM43436S, the former being upstream names and the
latter downstream names for differently-sourced sister parts.
Make the choice of firmwares board-specific (without making the actual
firmwares board-specific) by placing the alternative firmware names for
each part in the DT node.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Retain the old names for backwards compatibility for a while, while the
necessary firmware change rolls out.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
clk-2835 is deprecated and gets an innacurate clock for VEC (107MHz).
Switch to clk-raspberrypi which uses the right PLL to get an accurate 108MHz.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
A regression introduced in https://github.com/raspberrypi/linux/pull/3887
meant that if the newly scheduled transfer immediately returned data, and
the driver resubmitted a single URB after every transfer, then the effective
polling interval would end up being approx 1ms.
Use the larger of SCHEDULE_SLOP or the configured endpoint interval.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Adds an overlay to configure the TinyDRM driver for ST7735R
based 160x128 and 128x128 (untested) displays such as the
Adafruit 1.8" display.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
This commit updates the imx519 driver to adverise support for embedded
data streams.
The imx519 sensor subdevice overloads the media pad to differentiate
between image stream (pad 0) and embedded data stream (pad 1) when
performing the v4l2_subdev_pad_ops functions.
Signed-off-by: Lee Jackson <info@arducam.com>
Adds a driver for the 16MPix IMX519 CSI2 sensor.
Whilst the sensor supports 2 or 4 CSI2 data lanes, this driver
currently only supports 2 lanes.
The following Bayer modes are currently available:
4656x3496 10-bit @ 10fps
3840x2160 10-bit (cropped) @ 21fps
2328x1748 10-bit (binned) @ 30fps
1920x1080 10-bit (cropped/binned) @ 60fps
1280x720 10-bit (cropped/binned) @ 120fps
Signed-off-by: Lee Jackson <info@arducam.com>
The Linux support for controlling card power via regulators appears to
be contentious. I would argue that the default behaviour is contrary to
the SDHCI spec - turning off the power writes a reserved value to the
SD Bus Voltage Select field of the Power Control Register, which
seems to kill the Arasan/iProc controller - but fortunately there is a
hook in sdhci_ops to override the behaviour.
Signed-off-by: Juerg Haefliger <juergh@canonical.com>
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
This reverts commit aed19399a0.
Commit 6c92ae1e45 ("mmc: sdhci: Introduce sdhci_set_power_and_bus_voltage()")
introduced a generic helper that does the same thing so use that instead in
the following commit.
Signed-off-by: Juerg Haefliger <juergh@canonical.com>
Check for errors only if we actually tried to enable the bvb clock.
Fixes: 01a6d727b4 ("vc4/drm: hdmi: Handle case when bvb clock is null")
Signed-off-by: Juerg Haefliger <juergh@canonical.com>
When doing an asynchronous page flip (PAGE_FLIP ioctl with the
DRM_MODE_PAGE_FLIP_ASYNC flag set), the current code waits for the
possible GPU buffer being rendered through a call to
vc4_queue_seqno_cb().
On the BCM2835-37, the GPU driver is part of the vc4 driver and that
function is defined in vc4_gem.c to wait for the buffer to be rendered,
and once it's done, call a callback.
However, on the BCM2711 used on the RaspberryPi4, the GPU driver is
separate (v3d) and that function won't do anything. This was working
because we were going into a path, due to uninitialized variables, that
was always scheduling the callback.
However, we were never actually waiting for the buffer to be rendered
which was resulting in frames being displayed out of order.
The generic API to signal those kind of completion in the kernel are the
DMA fences, and fortunately the v3d drivers supports them and signal
when its job is done. That API also provides an equivalent function that
allows to have a callback being executed when the fence is signalled as
done.
Let's change our driver a bit to rely on the previous function for the
older SoCs, and on DMA fences for the BCM2711.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The read and write functions did not use the correct pointer offset
when dealing with an odd number of bytes after a DMA transfer. Also,
only handle the remaining odd bytes if the DMA transfer completed
successfully.
Submitted-by: @madimario (GitHub)
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The driver was implementing a get_brightness function that
tried to read back the PWM setting of the display to report
as the current brightness.
The controller on the display does not support that, therefore
we end up reporting a brightness of 0, and that confuses
systemd's backlight service.
Remove the hook so that the framework returns the current
brightness automatically.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
This allows using the video-i2c camera driver with MLX90640 thermal
infrared sensors, connected to Raspberry Pi. CONFIG_VIDEO_V4L2_I2C
has to be selected to use the camera.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
The ISP can do H & V flips whilst resizing or converting
the image, so expose that via V4L2_CID_[H|V]FLIP.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Currently the code was only setting some controls from
bcm2835_codec_set_ctrls, but it's simpler to use
v4l2_ctrl_handler_setup to avoid forgetting to adding new
controls to the list.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Completions don't reference count, so setting the completion
on the first buffer returned and then not reinitialising it
means that the flush function doesn't behave as intended.
Signal the completion when the last buffer is returned.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Should we go through the timeout failure case with port_disable
not returning all buffers for whatever reason, the
buffers_with_vpu counter gets left at a non-zero value, which
will cause reference counting issues should the instance be
reused.
Reset the count when the port is enabled again, but before
any buffers have been sent to the VPU.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
When a buffer is returned on a port that is disabled, return it
to the videobuf2 QUEUED state instead of DONE which returns it
to the client.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The firmware defaults to not stopping video decode if only the
pixel aspect ratio or colourspace change. V4L2 requires us
to stop decoding on any change, therefore tell the firmware
of the desire for this alternate behaviour.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
When a format changed event occurs, the spec says that it
triggers an implicit drain, and that needs to be signalled
via -EPIPE.
For BCM2835, the format changed event happens at the point
the format change occurs, so no further buffers exist from
before the resolution changed point. We therefore signal the
last buffer immediately.
We don't have a V4L2 available to us at this point, so set
the videobuf2 queue last_buffer_dequeued flag directly.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The list of includes was slightly over generic, and wasn't
in alphabetical order. Clean it up.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
With video decode we now enable both input and output ports on
the component. This means that buffers will get passed to the VPU
earlier than desired if they are queued befoer STREAMON.
Check that the queue is streaming before sending buffers to the VPU.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The V4L2 stateful video decoder API requires that you can STREAMON
on only the OUTPUT queue, feed in buffers, and wait for the
SOURCE_CHANGE event.
This requires that we enable the MMAL output port at the same time
as the input port, because the output port is the one that creates
the SOURCE_CHANGED event.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Before uniniting the decode context sync with the IRQ queues to ensure
that decode no longer has any buffers in use. This fixes a problem that
manifested as ffmpeg leaking CMA buffers when it did a stream off on
OUTPUT before CAPTURE, though in reality it was probably much more
dangerous than that.
Signed-off-by: John Cox <jc@kynesim.co.uk>
Remove unused ctx state tracking variable and associated defines.
Their presence implies they might be used, but they aren't.
Signed-off-by: John Cox <jc@kynesim.co.uk>
With EDPWRDOWN set in idle, it must be cleared before checking for
ENERGYON going high, indicating that a link is being established.
The existing code allows 640ms for ENERGYON to go high, but on
Raspberry Pis that appears not to be enough, causing link detection
to fail.
Increase the polling timeout to 1500ms - with a polling interval of
10ms it shouldn't cause unnecessary delays.
See: https://github.com/raspberrypi/linux/issues/4393
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
V4L2 spec says that G/S/TRY_FMT IOCTLs should never return errors for
anything other than wrong buffer types. Improve the capture format
function such that this is so and unsupported values get converted
to supported ones properly.
Signed-off-by: John Cox <jc@kynesim.co.uk>
A failure of some CPU cores to come online has been traced to the
failure of a stm instruction while the cache is disabled. The symptom
is that the saved values read back as zeroes, a catastrophic error since
one of the values is a return address.
This patch forces a readback and retry until the correct value is
returned,
Notes:
At this stage in the boot process the core is running with its cache
disabled. Before enabling the cache its contents must be explicitly
invalidated, a process that requires quite a few registers that the
caller must preserve. Evidence suggests that something is writing a
block of zeroes over that space at a time when all other cores should
be idle, possibly some kind of write-combiner, and retrying is an
attempt to avoid the problem.
The previous attempted fix (forcing the accesses to only be 4-byte
aligned) appears to have only worked for a while and likely for less
obvious reasons such as a change in code alignment.
See: https://github.com/Hexxeh/rpi-firmware/issues/232
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
This reverts commit fe4cc0ed59.
The speculative patch that this commit reverts is proving to not be
effective any more, so revert it and try a new approach.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
As we're wanting to wrap the image_fx component for deinterlacing,
add the deinterlace algorithm values to enum mmal_parameter_imagefx
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
If the client provides a bytesperline value in try_fmt/s_fmt then
validate it and correct if necessary.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Should start_streaming fail, or buffers be queued during
stop_streaming, they should be returned to the core as QUEUED
and not (as currently) as ERROR.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The video decoder can support decoding interlaced streams, so add
the required plumbing to signal this correctly.
The encoder and ISP do NOT support interlaced data, so trying to
configure an interlaced format on those nodes will be rejected.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Adds enum mmal_interlace_type and struct
mmal_parameter_video_interlace_type to allow for querying the
interlacing mode on decoders.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
In order to effectively guarantee that a V4L2_EVENT_SOURCE_CHANGE
event occurs, adopt a default resolution of 32x32 so that it
is incredibly unlikely to be decoding a stream of that resolution
and therefore failing to note a "change" requiring the event.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The exit path of vc4_hdmi_encoder_pre_crtc_configure() is fairly hard to
maintain given its numerous error conditions.
Switch to a goto based approach to simplify it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Unlike pm_runtime_get_sync(), pm_runtime_resume_and_get() doesn't take a
reference on failure, so we don't need to call pm_runtime_put() on
failure.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Our detect function calls pm_runtime_resume_and_get() and
pm_runtime_put() to make sure the device is properly powered before
trying to access the controller.
However, it also makes sure the HSM clock is properly enabled (and
disabled), which is redundant with what runtime_pm is doing already.
Let's just remove it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The older panel-raspberrypi-touchscreen driver had issues in
that it also controlled the power for the touchscreen without
having an appropriate hook for the touchscreen driver to control
that.
Mainline has now added a Toshiba TC358762 bridge driver, and
a regulator/backlight driver for the ATTiny microcontroller on
the board. That allows clean integration with the touchscreen
driver.
Switch the overlays over to using newer drivers.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
We need independent control of the resets for the panel&bridge,
vs the touch controller.
Expose the reset lines that are on the Atmel's port C via the GPIO
API so that they can be controlled appropriately.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The Atmel was doing a load of automatic sequencing of
control lines, however it was combining the touch controller's
reset with the bridge/panel control.
Change to control the control signals directly rather than
through the automatic POWERON control.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The initial state of the Atmel is not defined, so ensure the
backlight PWM is set to 0 by default.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The driver was using the regmap lock to serialise the
individual accesses, but we really need to protect the
timings of enabling the regulators, including any communication
with the Atmel.
Use a mutex within the driver to control overall accesses to
the Atmel, instead of the regmap lock.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The Atmel is doing some things in the I2C ISR, during which
period it will not respond to further commands. This is
particularly true of the POWERON command.
Increase delays appropriately, and retry should I2C errors be
reported.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
There's no reason why 2 Raspberry Pi DSI displays can't be
attached to a Pi Compute Module, so the backlight names need to
be unique.
Use the parent dev_name. It's not as readable, but is unique.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
If no interrupt is defined then a timer and workqueue are used
to poll the controller.
On remove these were not being cleaned up correctly.
Fixes: ca61fdaba7 "Input: edt-ft5x06: Poll the device if no interrupt is
configured."
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The Raspberry Pi 7" 800x480 panel uses a Toshiba TC358762 DSI
to DPI bridge chip, so there is a requirement for the timings
to be specified for the end panel. Add such a definition.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
rpi_touchscreen_i2c_read returns any errors from i2c_transfer,
or the 8 bit received value.
Check for error values before trying to process the data as
valid.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The panel has a prepare call which is before video starts, and an
enable call which is after.
The Toshiba bridge should be configured before video, so move
the relevant power and initialisation calls to prepare.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
If a call to rpi_touchscreen_i2c_write from rpi_touchscreen_probe
fails before mipi_dsi_device_register_full is called, then
in trying to log the error message if uses ts->dsi->dev when
it is still NULL.
Use ts->i2c->dev instead, which is initialised earlier in probe.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The divider calculations tried to find the divider
just faster than the clock requested. However if
it required a divider of 7 then the for loop
aborted without handling the "error" case, and could
end up with a clock lower than requested.
Correct the loop so that we always have a clock greater
than requested.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
On Pi0-3 the driver allocates a buffer and requests a DMA channel
because the ARM can't write to DSI1's registers directly.
However unbind and the error paths in bind don't release the buffer or
the DMA channel.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The HDMI block can repeat pixels for double clocked modes,
and the firmware is now configuring the block to do this as
the PV is doing it incorrectly when at 2pixels/clock.
If the kernel doesn't reset it then we end up with strange
modes.
Reset MISC_CONTROL.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The sysfs delay_ms value is calculated live, and it is possible for
the time left to appear to be negative briefly if the timer handling
hasn't completed. Ensure the displayed value never goes below zero,
for the sake of appearances.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
A module parameter "dpc_enable" is added to allow the control of the
sensor's on-board DPC (Defective Pixel Correction) function.
This is a global setting to be configured before using the sensor;
there is no intention that this would ever be changed on-the-fly.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
drm_connector_helper_hpd_irq_event() calls
drm_kms_helper_hotplug_event() with the mode-setting lock taken while
it's supposed to be called without that lock taken.
This results in a lockdep warning, and a deadlock if we were to wake up
a TV through CEC (and possibly other cases).
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
This adds an overlay to connect the QCA7000 in UART mode via UART0.
The qcauart driver uses the serial device bus instead of deprecated
line disciplines.
Signed-off-by: Stefan Wahren <stefan.wahren@in-tech.com>
When the firmware doesn't setup the HSM rate (such as when booting
without an HDMI cable plugged in), its rate is 0 and thus any register
access results in a CPU stall, even though HSM is enabled.
Let's enforce a minimum rate at boot to avoid this issue.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Commit 9d44abbbb8 ("drm/vc4: Fall back to using an EDID probe in the
absence of a GPIO.") added some code to read the EDID through DDC in the
HDMI driver detect hook since the Pi3 had no HPD GPIO back then.
However, commit b1b8f45b31 ("ARM: dts: bcm2837: Add missing GPIOs of
Expander") changed that a couple of years later.
This causes an issue though since some TV (like the LG 55C8) when it
comes out of standy will deassert the HPD line, but the EDID will
remain readable.
It causes an issues nn platforms without an HPD GPIO, like the Pi4,
where the DDC probing will be our primary mean to detect a display, and
thus we will never detect the HPD pulse. This was fine before since the
pulse was small enough that we would never detect it, and we also didn't
have anything (like the scrambler) that needed to be set up in the
display.
However, now that we have both, the display during the HPD pulse will
clear its scrambler status, and since we won't detect the
disconnect/reconnect cycle we will never enable the scrambler back.
As our main reason for that DDC probing is gone, let's just remove it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The drm_helper_hpd_irq_event() documentation states that this function
is "useful for drivers which can't or don't track hotplug interrupts for
each connector." and that "Drivers which support hotplug interrupts for
each connector individually and which have a more fine-grained detect
logic should bypass this code and directly call
drm_kms_helper_hotplug_event()". This is thus what we ended-up doing.
However, what this actually means, and is further explained in the
drm_kms_helper_hotplug_event() documentation, is that
drm_kms_helper_hotplug_event() should be called by drivers that can
track the connection status change, and if it has changed we should call
that function.
This underlying expectation we failed to provide is that the caller of
drm_kms_helper_hotplug_event() should call drm_helper_probe_detect() to
probe the new status of the connector.
Since we didn't do it, it meant that even though we were sending the
notification to user-space and the DRM clients that something changed we
never probed or updated our internal connector status ourselves.
This went mostly unnoticed since the detect callback usually doesn't
have any side-effect. Also, if we were using the DRM fbdev emulation
(which is a DRM client), or any user-space application that can deal
with hotplug events, chances are they would react to the hotplug event
by probing the connector status eventually.
However, now that we have to enable the scrambler in detect() if it was
enabled it has a side effect, and an application such as Kodi or
modetest doesn't deal with hotplug events. This resulted with a black
screen when Kodi or modetest was running when a screen was disconnected
and then reconnected, or switched off and on.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The drm_helper_hpd_irq_event() function is iterating over all the
connectors when an hotplug event is detected.
During that iteration, it will call each connector detect function and
figure out if its status changed.
Finally, if any connector changed, it will notify the user-space and the
clients that something changed on the DRM device.
This is supposed to be used for drivers that don't have a hotplug
interrupt for individual connectors. However, drivers that can use an
interrupt for a single connector are left in the dust and can either
reimplement the logic used during the iteration for each connector or
use that helper and iterate over all connectors all the time.
Since both are suboptimal, let's create a helper that will only perform
the status detection on a single connector.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The PoE HAT cooling levels are not well suited for the PoE+ HAT - the
fan fails to come on until the temperature reaches the third trip point
(50C).
Give the rpi-poe-plus overlay a different set of cooling levels -
0 32 64 128 255, as suggested by @chris-kai-in.
See: https://github.com/raspberrypi/firmware/issues/1607
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
See https://github.com/raspberrypi/linux/issues/3981
An unknown unsafe memory access can result in the ep_state variable
in xhci_virt_ep being trampled with a stuck SET_DEQ_PENDING state
despite successful completion of a Set TR Deq Pointer command.
All URB enqueue/dequeue calls for the endpoint will fail in this state
so no transfers are possible until the device is reconnected.
As a workaround, clear the flag if we see it set and issue a new Set
TR Deq command anyway - this should be harmless, as a prior Set TR Deq
command will only have been issued in the Stopped state, and if the
endpoint is Running then the controller is required to ignore it and
respond with a Context State Error event TRB.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Reduce the default CMA allocation requested by the vc4-kms-v3d-pi4 and
vc4-fkms-v3d-pi4 overlays to 320MB.
Use magic values of the form (<n>*64 - 4)MB to encode default values
of <n>*64MB, allowing these defaults to be distinguished from values
set explicitly by the user with the usual overlay parameters (e.g.
"cma-384"). Only default values will be capped if the Pi RAM is too
small or the gpu_mem setting too large for it to be viable.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Add call to v4l2_ctrl_new_fwnode_properties to read and
create the fwnode based controls.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Add call to v4l2_ctrl_new_fwnode_properties to read and
create the fwnode based controls.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Add call to v4l2_ctrl_new_fwnode_properties to read and
create the fwnode based controls.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Add the orientation parameter to all the camera sensor overlays to
avoid libcamera complaining, and add the rotation parameter where
it hadn't been added before.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
There are no error exists once device_create has succeeded, and
therefore no need to call device_destroy from vc_mem_init.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The firmware patches the PHY MDIO address in the DTB to cope with
variations between board revisions, but the default for the CM4 PHY
is currently 1 when it should be 0.
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Pi 4s have at least 1GB, and there are advantages to having more CMA
available (HEVC works out of the box, support for more complex video
setups, etc.) without significant disadvantages.
Can be overridden by appending a parameter to the dtoverlay line, e.g.
dtoverlay=vc4-fkms-v3d,cma-256
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
In the bind hook, we actually need the device to have the HSM clock
running during the final part of the display initialisation where we
reset the controller and initialise the CEC component.
Failing to do so will result in a complete, silent, hang of the CPU.
Fixes: 411efa18e4 ("drm/vc4: hdmi: Move the HSM clock enable to runtime_pm")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
[ drm-misc commit 2eecd93b74 ]
There'a limit to how big a kmalloc buffer can be, and as memory gets
fragmented it becomes more difficult to get big buffers. The downside of
smaller buffers is that the driver has to split the transfer up which
hampers performance. Compression might also take a hit because of the
splitting.
Solve this by allocating the transfer buffer using vmalloc and create a
SG table to be passed on to the USB subsystem. vmalloc_32() is used to
avoid DMA bounce buffers on USB controllers that can only access 32-bit
addresses.
This also solves the problem that split transfers can give host side
tearing since flushing is decoupled from rendering.
usb_sg_wait() doesn't have timeout handling builtin, so it is wrapped in
a timer like 4 out of 6 users in the kernel have done.
v2:
- Use DIV_ROUND_UP (Linus)
- Add timeout note to the commit log (Linus)
- Expand note about upper buffer limit (Linus)
- Change var name s/timer/ctx/ in gud_usb_bulk_timeout()
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210701170748.58009-2-noralf@tronnes.org
[ drm-misc commit f8ac863b6a ]
Free transfer and compression buffers on device removal instead of at
DRM device removal time. This ensures that the usual 2x8MB buffers are
released when the device is unplugged and not kept around should
userspace keep the DRM device fd open.
At least Ubuntu 20.04 doesn't release the DRM device on unplug.
The damage_lock mutex is not destroyed because it is used outside the
drm_dev_enter/exit block in gud_pipe_update(). AFAICT it's possible for
an open fbdev descriptor to trigger a commit after the USB device is gone.
v2: Don't destroy damage_lock
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210701170748.58009-1-noralf@tronnes.org
[ Upstream commit 40e1a70b4a ]
This adds a USB display driver with the intention that it can be
used with future USB interfaced low end displays/adapters. The Linux
gadget device driver will serve as the canonical device implementation.
The following DRM properties are supported:
- Plane rotation
- Connector TV properties
There is also support for backlight brightness exposed as a backlight
device.
Display modes can be made available to the host driver either as DRM
display modes or through EDID. If both are present, EDID is just passed
on to userspace.
Performance is preferred over color depth, so if the device supports
RGB565, DRM_CAP_DUMB_PREFERRED_DEPTH will return 16.
If the device transfer buffer can't fit an uncompressed framebuffer
update, the update is split up into parts that do fit.
Optimal user experience is achieved by providing damage reports either by
setting FB_DAMAGE_CLIPS on pageflips or calling DRM_IOCTL_MODE_DIRTYFB.
LZ4 compression is used if the device supports it.
The driver supports a one bit monochrome transfer format: R1. This is not
implemented in the gadget driver. It is added in preparation for future
monochrome e-ink displays.
The driver is MIT licensed to smooth the path for any BSD port of the
driver.
v2:
- Use devm_drm_dev_alloc() and drmm_mode_config_init()
- drm_fbdev_generic_setup: Use preferred_bpp=0, 16 was a copy paste error
- The drm_backlight_helper is dropped, copy in the code
- Support protocol version backwards compatibility for device
v3:
- Use donated Openmoko USB pid
- Use direct compression from framebuffer when pitch matches, not only on
full frames, so split updates can benefit
- Use __le16 in struct gud_drm_req_get_connector_status
- Set edid property when the device only provides edid
- Clear compression fields in struct gud_drm_req_set_buffer
- Fix protocol version negotiation
- Remove mode->vrefresh, it's calculated
v4:
- Drop the status req polling which was a workaround for something that
turned out to be a dwc2 udc driver problem
- Add a flag for the Linux gadget to require a status request on
SET operations. Other devices will only get status req on STALL errors
- Use protocol specific error codes (Peter)
- Add a flag for devices that want to receive the entire framebuffer on
each flush (Lubomir)
- Retry a failed framebuffer flush
- If mode has changed wait for worker and clear pending damage before
queuing up new damage, fb width/height might have changed
- Increase error counter on bulk transfer failures
- Use DRM_MODE_CONNECTOR_USB
- Handle R1 kmalloc error (Peter)
- Don't try and replicate the USB get descriptor request standard for the
display descriptor (Peter)
- Make max_buffer_size optional (Peter), drop the pow2 requirement since
it's not necessary anymore.
- Don't pre-alloc a control request buffer, it was only 4k
- Let gud.h describe the whole protocol explicitly and don't let DRM
leak into it (Peter)
- Drop display mode .hskew and .vscan from the protocol
- Shorten names: s/GUD_DRM_/GUD_/ s/gud_drm_/gud_/ (Peter)
- Fix gud_pipe_check() connector picking when switching connector
- Drop gud_drm_driver_gem_create_object() cached is default now
- Retrieve USB device from struct drm_device.dev instead of keeping a
pointer
- Honour fb->offsets[0]
- Fix mode fetching when connector status is forced
- Check EDID length reported by the device
- Use drm_do_get_edid() so userspace can overrride EDID
- Set epoch counter to signal connector status change
- gud_drm_driver can be const now
v5:
- GUD_DRM_FORMAT_R1: Use non-human ascii values (Daniel)
- Change name to: GUD USB Display (Thomas, Simon)
- Change one __u32 -> __le32 in protocol header
- Always log fb flush errors, unless the previous one failed
- Run backlight update in a worker to avoid upsetting lockdep (Daniel)
- Drop backlight_ops.get_brightness, there's no readback from the device
so it doesn't really add anything.
- Set dma mask, needed by dma-buf importers
v6:
- Use obj-y in Makefile (Peter)
- Fix missing le32_to_cpu() when using GUD_DISPLAY_MAGIC (Peter)
- Set initial brightness on backlight device
v7:
- LZ4_compress_default() can return zero, check for that
- Fix memory leak in gud_pipe_check() error path (Peter)
- Improve debug and error messages (Peter)
- Don't pass length in protocol structs (Peter)
- Pass USB interface to gud_usb_control_msg() et al. (Peter)
- Improve gud_connector_fill_properties() (Peter)
- Add GUD_PIXEL_FORMAT_RGB111 (Peter)
- Remove GUD_REQ_SET_VERSION (Peter)
- Fix DRM_IOCTL_MODE_OBJ_SETPROPERTY and the rotation property
- Fix dma-buf import (Thomas)
v8:
- Forgot to filter RGB111 from reaching userspace
- Handle a device that only returns unknown device properties (Peter)
- s/GUD_PIXEL_FORMAT_RGB111/GUD_PIXEL_FORMAT_XRGB1111/ (Peter)
- Fix R1 and XRGB1111 format conversion
- Add FIXME about Big Endian being broken (Peter, Ilia)
Cc: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: Peter Stuge <peter@stuge.se>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210313112545.37527-4-noralf@tronnes.org
[ backport changes:
- Remove include drm_gem_atomic_helper.h
- s/drm_gem_simple_display_pipe_prepare_fb/drm_gem_fb_simple_display_pipe_prepare_fb/
- Remove const from gud_drm_driver
- Change drm_gem_shmem_{vmap,vunmap} signatures
- Add gud_gem_create_object() to get cached memory mapping.
]
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
The imx477 driver's line length for this mode had not been updated to
the value supplied to us by the sensor manufacturer. With this
correction the sensor delivers the framerates that are expected.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
The bcm2711 vc3-kms-v3d overlay enables the I2C instances used for
EDID data. Give these distinct I2C interface numbers (20 & 21) to
clearly separate them from other regular I2C blocks (1, 3-6) and the
mux on I2C0 (10+).
The 2711 DTS tree no longer includes i2c2, so the explicit deletion can
be removed.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Replace drm_encoder_helper_funcs::atomic_check with
drm_connector_helper_funcs::atomic_check - the former is not called
during drm_mode_obj_set_property_ioctl(). Set crtc_state->mode_changed
if TV norm changes even without explicit mode change. This makes things
like "xrandr --output Composite-1 --set mode PAL-M" work properly.
Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
Similar to the ch7006 and nouveau drivers, introduce a "tv_mode" module
parameter that allow setting the TV norm by specifying vc4.tv_norm= on
the kernel command line.
If that is not specified, try inferring one of the most popular norms
(PAL or NTSC) from the video mode specified on the command line. On
Raspberry Pis, this causes the most common cases of the sdtv_mode
setting in config.txt to be respected.
Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
Add support for the following composite output modes (all of them are
somewhat more obscure than the previously defined ones):
- NTSC_443 - NTSC-style signal with the chroma subcarrier shifted to
4.43361875 MHz (the PAL subcarrier frequency). Never used for
broadcasting, but sometimes used as a hack to play NTSC content in PAL
regions (e.g. on VCRs).
- PAL_N - PAL with alternative chroma subcarrier frequency,
3.58205625 MHz. Used as a broadcast standard in Argentina, Paraguay
and Uruguay to fit 576i50 with colour in 6 MHz channel raster.
- PAL60 - 480i60 signal with PAL-style color at normal European PAL
frequency. Another non-standard, non-broadcast mode, used in similar
contexts as NTSC_443. Some displays support one but not the other.
- SECAM - French frequency-modulated analog color standard; also have
been broadcast in Eastern Europe and various parts of Africa and Asia.
Uses the same 576i50 timings as PAL.
Also added some comments explaining color subcarrier frequency
registers.
Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
PAL-M is a Brazilian analog TV standard that uses a PAL-style chroma
subcarrier at 3.575611[888111] MHz on top of 525-line (480i60) timings.
This commit makes the driver actually use the proper VEC preset for this
mode instead of just changing PAL subcarrier frequency.
DRM mode constant names have also been changed, as they no longer
correspond to the "NTSC" or "PAL" terms.
Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
Change the mode_set function pointer logic to declarative config0,
config1 and custom_freq fields, to make TV mode setting logic more
concise and uniform.
Additionally, remove the superfluous tv_mode field, which was redundant
with the mode field in struct drm_tv_connector_state.
Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
This commit fixes vertical timings of the VEC (composite output) modes
to accurately represent the 525-line ("NTSC") and 625-line ("PAL") ITU-R
standards.
Previous timings were actually defined as 502 and 601 lines, resulting
in non-standard 62.69 Hz and 52 Hz signals being generated,
respectively.
Changes to vc4_crtc.c have also been made, to make the PixelValve
vertical timings accurately correspond to the DRM modeline in interlaced
modes. The resulting VERTA/VERTB register values have been verified
against the reference values set by the Raspberry Pi firmware.
Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
The new vec node in bcm2711.dtsi should have the correct interrupt
number to start with, rather than include the bcm283x version and
patch it later.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The calculations clipped the right/bottom edge of the clipped
range based on the left/top margins.
Fixes: 666e73587f ("drm/vc4: Take margin setup into account when updating planes")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The alternative is to move them into the source file that uses then,
but they are large and intrusive, so that strategy is being avoided.
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/vc4/vc4_hdmi_regs.h:282:39: warning: ‘vc5_hdmi_hdmi1_fields’ defined but not used [-Wunused-const-variable=]
drivers/gpu/drm/vc4/vc4_hdmi_regs.h:206:39: warning: ‘vc5_hdmi_hdmi0_fields’ defined but not used [-Wunused-const-variable=]
drivers/gpu/drm/vc4/vc4_hdmi_regs.h:145:39: warning: ‘vc4_hdmi_fields’ defined but not used [-Wunused-const-variable=]
Cc: Eric Anholt <eric@anholt.net>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20201116174112.1833368-38-lee.jones@linaro.org
idr_init() uses base 0 which is an invalid identifier for this driver.
The idr_alloc for this driver uses VC4_PERFMONID_MIN as start value for
ID range and it is #defined to 1. The new function idr_init_base allows
IDR to set the ID lookup from base 1. This avoids all lookups that
otherwise starts from 0 since 0 is always unused / available.
References: commit 6ce711f275 ("idr: Make 1-based IDRs more efficient")
Signed-off-by: Deepak R Varma <mh12gx2825@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20201105202135.GA145111@localhost
To support legacy gamma ioctls the drivers need to set
drm_crtc_funcs.gamma_set either to a custom implementation or to
drm_atomic_helper_legacy_gamma_set. Most of the atomic drivers do the
latter.
We can simplify this by making the core handle it automatically.
Move the drm_atomic_helper_legacy_gamma_set() functionality into
drm_color_mgmt.c to make drm_mode_gamma_set_ioctl() use
drm_crtc_funcs.gamma_set if set or GAMMA_LUT property if not.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201211114237.213288-2-tomi.valkeinen@ti.com
Now that atomic_check takes the global atomic state as a parameter, we
don't need to go through the pointer in the CRTC state.
This was done using the following coccinelle script:
@ crtc_atomic_func @
identifier helpers;
identifier func;
@@
static struct drm_crtc_helper_funcs helpers = {
...,
.atomic_check = func,
...,
};
@@
identifier crtc_atomic_func.func;
identifier crtc, state;
@@
func(struct drm_crtc *crtc, struct drm_atomic_state *state) {
...
- struct drm_crtc_state *crtc_state = drm_atomic_get_new_crtc_state(state, crtc);
... when != crtc_state
- crtc_state->state
+ state
...
}
@@
struct drm_crtc_state *crtc_state;
identifier crtc_atomic_func.func;
identifier crtc, state;
@@
func(struct drm_crtc *crtc, struct drm_atomic_state *state) {
...
- crtc_state->state
+ state
...
}
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201102133834.1176740-3-maxime@cerno.tech
The core clock needs to be raised temporarily during a modeset to
500MHz. However, the HVS core clock requirement might be higher than
500MHz. This rate will be enforced at the end of the mode setting,
meaning that might might end up with a core clock rate lower than
planned on the first mode set.
Use the maximum value of 500MHz and the HVS core clock rate for our
temporary boost to fix this issue.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Depending on a given HVS output (HVS to PixelValves) and input (planes
attached to a channel) load, the HVS needs for the core clock to be
raised above its boot time default.
Failing to do so will result in a vblank timeout and a stalled display
pipeline.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Now that the semaphore is gone, our atomic_commit implementation is
basically drm_atomic_helper_commit with a somewhat custom commit_tail,
the main difference being that we're using wait_for_flip_done instead of
wait_for_vblanks used in the drm_atomic_helper_commit_tail helper.
Let's switch to using drm_atomic_helper_commit.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Now that we have proper ordering guaranteed by the previous patch, the
semaphore is redundant and can be removed.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The HVS state now has both unassigned_channels that reflects the
channels that are not used in the associated state, and the in_use
boolean for each channel that says whether or not a particular channel
is in use.
Both express pretty much the same thing, and we need the in_use variable
to properly track the commits, so let's get rid of unassigned_channels.
Suggested-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20201204151138.1739736-6-maxime@cerno.tech
If we're having two subsequent, non-blocking, commits on two different
CRTCs that share no resources, there's no guarantee on the order of
execution of both commits.
However, the second one will consider the first one as the old state,
and will be in charge of freeing it once that second commit is done.
If the first commit happens after that second commit, it might access
some resources related to its state that has been freed, resulting in a
use-after-free bug.
The standard DRM objects are protected against this, but our HVS private
state isn't so let's make sure we wait for all the previous FIFO users
to finish their commit before going with our own.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we can't allocate a new channel, we can simply return instead of
having to handle both cases, and that simplifies a bit the code.
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The private objects have a gotcha that could result in a use-after-free,
make sure it's properly documented.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Private objects storing a state shared across all CRTCs need to be
carefully handled to avoid a use-after-free issue.
The proper way to do this to track all the commits using that shared
state and wait for the previous commits to be done before going on with
the current one to avoid the reordering of commits that could occur.
However, this commit setup needs to be done after
drm_atomic_helper_setup_commit(), because before the CRTC commit
structure hasn't been allocated before, and before the workqueue is
scheduled, because we would be potentially reordered already otherwise.
That means that drivers currently have to roll their own
drm_atomic_helper_commit() function, even though it would be identical
if not for the commit setup.
Let's introduce a hook to do so that would be called as part of
drm_atomic_helper_commit, allowing us to reuse the atomic helpers.
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The vidioc_enum_input() v4l2 ioctl is capable of returning
sensor/input status as well. This is used in current
GStreamer HEAD for signal detection [1].
bcm2835-unicam does handle this syscall, but it didn't ask
the subdevice driver about the input status. The input then
appeared as always present.
This commit adds the necessary query. There is a precedent for
this - the R-Car VIN V4L2 driver does a similar call [2].
[1]: ce0be27caf/sys/v4l2/gstv4l2src.c (L553)
[2]: 7fb9d006d3/drivers/media/platform/rcar-vin/rcar-v4l2.c (L548)
Signed-off-by: Jakub Vaněk <linuxtardis@gmail.com>
Our hotplug handler will currently call the drm_kms_helper_hotplug_event
every time a hotplug interrupt is called.
However, since the device is registered after all the drivers have
finished their bind callback, we have a window between when we install
our interrupt handler and when drm_dev_register() is eventually called
where our handler can run and call drm_kms_helper_hotplug_event but the
device hasn't been registered yet, causing a null pointer dereference.
Fix this by making sure we only call drm_kms_helper_hotplug_event if our
device has been properly registered.
Fixes: f4790083c7 ("drm/vc4: hdmi: Rely on interrupts to handle hotplug")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The hotplugs interrupt handlers are registered through the
devm_request_threaded_irq function. However, while free_irq is indeed
called properly when the device is unbound or bind fails, it's called
after unbind or bind is done.
In our particular case, it means that on failure it creates a window
where our interrupt handler can be called, but we're freeing every
resource (CEC adapter, DRM objects, etc.) it might need.
In order to address this, let's switch to the non-devm variant to
control better when the handler will be unregistered and allow us to
make it safe.
Fixes: f4790083c7 ("drm/vc4: hdmi: Rely on interrupts to handle hotplug")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The CEC interrupt handlers are registered through the
devm_request_threaded_irq function. However, while free_irq is indeed
called properly when the device is unbound or bind fails, it's called
after unbind or bind is done.
In our particular case, it means that on failure it creates a window
where our interrupt handler can be called, but we're freeing every
resource (CEC adapter, DRM objects, etc.) it might need.
In order to address this, let's switch to the non-devm variant to
control better when the handler will be unregistered and allow us to
make it safe.
Fixes: 15b4511a4a ("drm/vc4: add HDMI CEC support")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
NetBSD have changed their licensing requirements such that the 2-clause
licence is preferred. Update usb.h in the downstream dwc_otg code
accordingly.
See https://www.netbsd.org/about/redistribution.html for more
information.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Commit ecdd08fd9b ("drm/vc4: hdmi: Make sure the device is powered
with CEC") made sure that the device is powered while there is
CEC-related accesses but missed one register read in the variable
declaration.
Move the variable assignment after the pm_runtime_resume_and_get.
Fixes: ecdd08fd9b ("drm/vc4: hdmi: Make sure the device is powered with CEC")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
We've had many silent hangs where the kernel would look like it just
stalled due to the access to one of the HDMI registers while the
controller was disabled.
Add a warning if we're about to do that so that it's at least not silent
anymore.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
In vc4_hdmi_encoder_pre_crtc_configure, if clk_request_start for the HSM
clock fails, we don't call clk_disable_unprepare on the pixel clock even
though it's enabled by now.
Make sure it's there to avoid leaking that reference.
Fixes: cd4cb49dc5 ("drm/vc4: hdmi: Adjust HSM clock rate depending on pixel rate")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Similarly to what we encountered with the detect hook with DRM, nothing
actually prevents any of the CEC callback from being run while the HDMI
output is disabled.
However, this is an issue since any register access to the controller
when it's powered down will result in a silent hang.
Let's make sure we run the runtime_pm hooks when the CEC adapter is
opened and closed by the userspace to avoid that issue.
Fixes: 15b4511a4a ("drm/vc4: add HDMI CEC support")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
In order to ease further additions to the CEC enable and disable, let's
split the function into two functions, one to enable and the other to
disable.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
In the vc4_hdmi_encoder_pre_crtc_configure() function error path we
never actually call pm_runtime_put() even though
pm_runtime_resume_and_get() is our very first call.
Fixes: 4f6e3d66ac ("drm/vc4: Add runtime PM support to the HDMI encoder driver")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
In the bind hook, we actually need the device to have the HSM clock
running during the final part of the display initialisation where we
reset the controller and initialise the CEC component.
Failing to do so will result in a complete, silent, hang of the CPU.
Fixes: 411efa18e4 ("drm/vc4: hdmi: Move the HSM clock enable to runtime_pm")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The HPD GPIO retrieval code on failure will jump to the
err_unprepare_hsm label that calls pm_runtime_disable.
However at that point we haven't called pm_runtime_enable, so we end up
with an unbalanced call.
The next error than can occur (and therefore the next label) needs both
pm_runtime_disable and drm_encoder_cleanup though, so let's rearrange
the labels to match what we expect.
Fixes: cd4cb49dc5 ("drm/vc4: hdmi: Adjust HSM clock rate depending on pixel rate")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
In order to access the HDMI controller, we need to make sure the HSM
clock is enabled. If we were to access it with the clock disabled, the
CPU would completely hang, resulting in an hard crash.
Since we have different code path that would require it, let's move that
clock enable / disable to runtime_pm that will take care of the
reference counting for us.
Fixes: 4f6e3d66ac ("drm/vc4: Add runtime PM support to the HDMI encoder driver")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210525091059.234116-3-maxime@cerno.tech
Add the firmware phandle to the vc4 node so that we can send it the
message that we're done with the firmware display.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Once the call to drm_fb_helper_remove_conflicting_framebuffers() has
been made, simplefb has been unregistered and the KMS driver is entirely
in charge of the display.
Thus, we can notify the firmware it can free whatever resource it was
using to maintain simplefb functional.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The bind hooks will modify their controller registers, so simplefb is
going to be unusable anyway. Let's avoid any transient state where it
could still be in the system but no longer functionnal.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The RPI_FIRMWARE_NOTIFY_DISPLAY_DONE firmware call allows to tell the
firmware the kernel is in charge of the display now and the firmware can
free whatever resources it was using.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The vc4 driver will need to tell the firmware that it takes over the
display for the firmware to free its resources (lower the clock, free
some memory, etc.)
Let's add an optional phandle to our firmware node.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The raspberrypi,firmware property has been documented as required in the
binding but was never actually used in the final version of the binding.
Remove it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Lift the set of RTCs out of i2c-rtc and i2c-rtc-gpio to update
i2c-rtc-gpio and to reduce duplication.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The imx378 sensor is almost identical to the imx477 and can be
supported as a "compatible" sensor with just a few extra register
writes.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
The bcm2835 ISP requires the base address of all input/output planes to have 32
byte alignment. Using a Y stride of 32 bytes would not guarantee that the V
plane would fulfil this, e.g. a height of 650 lines would mean the V plane
buffer is not 32 byte aligned for YUV420 formats.
Having a Y stride of 64 bytes would ensure both U and V planes have a 32 byte
alignment, as the luma height will always be an even number of lines.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
From the requesting issue:
"This option is necessary for having bridge-like networking on KVM VMs
with the host root filesystem on NFS (since regular bridge networking
doesn't work in that case),"
See: https://github.com/raspberrypi/linux/issues/4413
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
If we have a state already and disconnect/reconnect the display, the
SCDC messages won't be sent again since we didn't go through a disable /
enable cycle.
In order to fix this, let's call the vc4_hdmi_enable_scrambling function
in the detect callback if there is a mode and it needs the scrambler to
be enabled.
Fixes: 74465b84fa ("drm/vc4: hdmi: Enable the scrambler")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Before the introduction of the BCM2711 support, the HSM clock rate was
fixed, and was the CEC and audio clock source on the SoCs previously
supported.
The HSM clock is also the source of the internal state machine of the
controller and needs to run faster than the pixel clock. All these
requirements were met by running at 101% of the maximum pixel rate,
meeting the fixed clock requirement for audio and CEC, while remaining
faster than any pixel clock we might need.
However, the BCM2711 brought support for 4k and therefore increased
significantly the rate needed for the HSM, and new, independant, clocks
to feed the audio and CEC clocks. Since the HSM clock can also run much
higher, we also need to lower its rate if possible to reduce its power
consumption.
The CEC support code changes its clock divider when the HSM clock rate
is changed, but the audio support never had a similar feature and will
glitch out if audio is played back during a mode set.
Since the HSM rate was meant to be fixed on the SoCs prior to the
BCM2711 anyway, let's introduce back a fixed HSM rate and fix audio.
Fixes: cd4cb49dc5 ("drm/vc4: hdmi: Adjust HSM clock rate depending on pixel rate")
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
From the original Rockchip driver, the subdev was renamed
from the default to being "mov9281 <dev_name>" whereas the
default would have been "ov9281 <dev_name>".
Remove the override to drop back to the default rather than
a vendor custom string.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The core clock needs to be raised temporarily during a modeset to
500MHz. However, the HVS core clock requirement might be higher than
500MHz. This rate will be enforced at the end of the mode setting,
meaning that might might end up with a core clock rate lower than
planned on the first mode set.
Use the maximum value of 500MHz and the HVS core clock rate for our
temporary boost to fix this issue.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Adjust the DVP enable/disable sequence to avoid a pixel getting stuck
in an internal, non resettable FIFO within PixelValve when changing
HDMI resolution.
The blank pixels features of the DVP can prevent signals back to
pixelvalve causing it to not clear the FIFO. Adjust the ordering
and timing of operations to ensure the clear signal makes it through to
pixelvalve.
Signed-off-by: Tim Gover <tim.gover@raspberrypi.com>
A matching media bus format was added and an overlay for using it,
both with FB and VC4 was added as well.
Signed-off-by: Joerg Quinten <aBUGSworstnightmare@gmail.com>
It is legitimate, though unusual, for an aux ent associated with a slot
to be selected in phase 0 before a previous selection has been used and
released in phase 2. Fix such that if the slot is found to be in use
that the aux ent associated with it is reused rather than an new aux
ent being created. This fixes a problem where when the first aux ent
was released the second was lost track of.
This bug spotted in Nick's testing. It may explain some other occasional,
unreliable decode error reports where dmesg included "Missing DPB AUX
ent" logging.
Signed-off-by: John Cox <jc@kynesim.co.uk>
Increase the number of post-sync blanking lines on odd fields instead of
decreasing it on even fields. This makes the total number of lines
properly match the modelines.
Additionally fix the value of PV_VCONTROL_ODD_DELAY, which did not take
pixels_per_clock into account, causing some displays to invert the
fields when driven by bcm2711.
Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
Depending on a given HVS output (HVS to PixelValves) and input (planes
attached to a channel) load, the HVS needs for the core clock to be
raised above its boot time default.
Failing to do so will result in a vblank timeout and a stalled display
pipeline.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The load tracker was initially designed to report and warn about a load
too high for the HVS. To do so, it computes for each plane the impact
it's going to have on the HVS, and will warn (if it's enabled) if we go
over what the hardware can process.
While the limits being used are a bit irrelevant to the BCM2711, the
algorithm to compute the HVS load will be one component used in order to
compute the core clock rate on the BCM2711.
Let's remove the hooks to prevent the load tracker to do its
computation, but since we don't have the same limits, don't check them
against them, and prevent the debugfs file to enable it from being
created.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The encoder retrieval code has been a source of bugs and glitches in the
past and the crtc <-> encoder association been wrong in a number of
different ways.
Add some logging to quickly spot issues if they occur.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
It turns out the encoder retrieval code, in addition to being
unnecessarily complicated, has a bug when only the planes and crtcs are
affected by a given atomic commit.
Indeed, in such a case, either drm_atomic_get_old_connector_state or
drm_atomic_get_new_connector_state will return NULL and thus our encoder
retrieval code will not match on anything.
We can however simplify the code by using drm_for_each_encoder_mask, the
drm_crtc_state storing the encoders a given CRTC is connected to
directly and without relying on any other state.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
vc4_crtc_config_pv() retrieves the encoder again, even though its only
caller, vc4_crtc_atomic_enable(), already did.
Pass the encoder pointer as an argument instead of going through all the
connectors to retrieve it again.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
When the clock setups were added for the alternate external clocks,
the settings for 2 lane 720p and 4 lane 1080p were transposed.
2 lane 720p still worked, but 4 lane 1080p didn't.
Correct the assignments.
Fixes: 6b0c094a5b (media: i2c: imx290: Add support for 74.25MHz clock")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Whilst the datasheet lists the link frequency changing between
1080p and 720p modes, reality is that with the default blanking
we have
(1920 + 280) * (1080 + 45) * 60fps = 148.5MPix/s
and
(1280 + 2020) * (720 + 30) * 60fps = 148.5MPix/s
and this reflects reality whether in 10 or 12 bit readout modes.
How this relates to link frequency is unclear as it differs
from the datasheet, but all exposure and frame rate calcs need
the pixel rate to be correct, so make it so.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Commit "97589ad61c73 media: i2c: imx290: Add support for 2 data lanes"
added support for running in two lane mode (instead of 4), but
without changing the link frequency that resulted in a max of 30fps.
Commit "98e0500eadb7 media: i2c: imx290: Add configurable link frequency
and pixel rate" then doubled the link frequency when in 2 lane mode,
but didn't undo the correction for running at only 30fps, just extending
horizontal blanking instead.
It also didn't update the CSI timing registers in accordance with the
datasheet.
Remove the 30fps limit on 2 lane by correcting the register config
in accordance with the datasheet for 60fps operation over 2 lanes.
Frame rate control (via V4L2_CID_VBLANK or HBLANK) can still reduce
the frame rate on 2 lanes back to 30fps.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
In order to allow containerised Android apps to run, add the following
config settings on 64-bit builds:
CONFIG_ANDROID=y
CONFIG_ANDROID_BINDER_IPC=y
CONFIG_ANDROID_BINDERFS=y
CONFIG_ASHMEM=y
This has a memory overhead of about 130kB and no other performance
penalty.
See: https://github.com/raspberrypi/linux/issues/4162
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Enable NO_WAIT_RESP, DMA_WIDE_SOURCE, DMA_WIDE_DEST, and bump the DMA
panic and AXI priorities to avoid any DMA transfer error with HBR audio
(8 channel, 192Hz).
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The hdmi-codec brings a lot of advanced features, including the HDMI
channel mapping. Let's use it in our driver instead of our own codec.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The IEC958 status bit is usually set by the userspace after hw_params
has been called, so in order to use whatever is set by the userspace, we
need to implement the prepare hook. Let's add it to the hdmi_codec_ops,
and mandate that either prepare or hw_params is implemented.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
In some situations, like a codec probe, we need to provide an IEC status
default but don't have access to the sampling rate and width yet since
no stream has been configured yet.
Each and every driver has its own default, whereas the core iec958 code
also has some buried in the snd_pcm_create_iec958_consumer functions.
Let's split these functions in two to provide a default that doesn't
rely on the sampling rate and width, and another function to fill them
when available.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
We're going to add more controls to support the IEC958 output, so let's
rework the control registration a bit to support more of them.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Depending on a given HVS output (HVS to PixelValves) and input (planes
attached to a channel) load, the HVS needs for the core clock to be
raised above its boot time default.
Failing to do so will result in a vblank timeout and a stalled display
pipeline.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
drm_atomic_get_crtc_state relies on drm_atomic_get_existing_crtc_state
that is deprecated and isn't really clear on which state it provides.
Even worse, after the states have been swapped, if the CRTC is present
in the state drm_atomic_get_existing_crtc_state will return the old
state, whereas if the CRTC is not present, we'll use a copy of
crtc->state. crtc->state for the CRTC that is there at that point is the new
state though, which leads to confusion.
Let's provide two new helpers that make it clear what our expectations
are.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
In the event that the ENABLE signal from the codec goes low before
RELAY2 has been enabled, wait until the full 1000ms has elapsed then
enable RELAY2 and jump to amp_on_wait, i.e. as if output had been
fully enabled then disabled, rather than returning to the amp_off
idle state.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Do not scale IMX477_EXPOSURE_OFFSET with the long exposure factor during
the limit calculations. This allows larger exposure times, and does seem to be
what the sensor is doing internally.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Increasing the sleep time after clock selection to 3-4ms
allows the correct detection of all combinations of DAC+ Pro
and DAC+ADC Pro sound cards and the various PI revisions.
Signed-off-by: Joerg Schambacher <joerg@hifiberry.com>
There is a CAN protocol named J1939 which is supported by Linux Kernel
since v5.4. Recently J1939 header file turned up in
raspberrypi-kernel-headers but the module is not built for kernel
v5.10.y due to the missing flag. Therefore set it to build as module:
CONFIG_CAN_J1939=m
Signed-off-by: Patrick Menschel <menschel.p@posteo.de>
Fix stream on & off such that failures leave the driver in the correct
state. Ensure that the clock is on when we are streaming and off when
all contexts attached to this device have stopped streaming.
Signed-off-by: John Cox <jc@kynesim.co.uk>
Due to overheads in assembling controls and requests it is worth having
the slice assembly phase separate from the h/w pass1 processing. Create
a queue to service pass1 rather than have the pass1 finished callback
trigger the next slice job.
This requires a rework of the logic that splits up the buffer and
request done events. This code contains two ways of doing that, we use
Ezequiel Garcias <ezequiel@collabora.com> solution, but expect that
in the future this will be handled by the framework in a cleaner manner.
Fix up the handling of some of the memory exhaustion crashes uncovered
in the process of writing this code.
Signed-off-by: John Cox <jc@kynesim.co.uk>
This is probably not the API we will want to add, but it
should show what semantics are needed by drivers.
The goal is to allow the OUTPUT (aka source) buffer and the
controls associated to a request to be released from the request,
and in particular return the OUTPUT buffer back to userspace,
without signalling the media request fd.
This is useful for devices that are able to pre-process
the OUTPUT buffer, therefore able to release it before
the decoding is finished. These drivers should signal
the media request fd only after the CAPTURE buffer is done.
Tested-by: John Cox <jc@kynesim.co.uk>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Add an enable count to the irq Q structures to allow the irq logic to
block further callbacks if resources associated with the irq are not
yet available.
Signed-off-by: John Cox <jc@kynesim.co.uk>
Use multi-planar interface rather than single plane interface. This
allows dmabufs holding compressed data to be resized.
Signed-off-by: John Cox <jc@kynesim.co.uk>
VAAPI H265 has num entry points but never sets it. Allow a VAAPI
shim to work without requiring rewriting the VAAPI driver.
num_entry_points can be calculated from the slice_segment_addr
of the next slice so delay processing until we have that.
Also includes some minor cosmetics.
Signed-off-by: John Cox <jc@kynesim.co.uk>
When a request is re-inited it will release all control handler
objects that are still in the request. It does that by unbinding
and putting all those objects. When the object is unbound the
obj->req pointer is set to NULL, and the object's unbind op is
called. When the object it put the object's release op is called
to free the memory.
For a request object that contains a control handler that means
that v4l2_ctrl_handler_free() is called in the release op.
A control handler used in a request has a pointer to the main
control handler that is created by the driver and contains the
current state of all controls. If the device is unbound (due to
rmmod or a forced unbind), then that main handler is freed, again
by calling v4l2_ctrl_handler_free(), and any outstanding request
objects that refer to that main handler have to be unbound and put
as well.
It does that by this test:
if (!hdl->req_obj.req && !list_empty(&hdl->requests)) {
I.e. the handler has no pointer to a request, so is the main
handler, and one or more request objects refer to this main
handler.
However, this test is wrong since hdl->req_obj.req is actually
NULL when re-initing a request (the object unbind will set req to
NULL), and the only reason this seemingly worked is that the
requests list is typically empty since the request's unbind op
will remove the handler from the requests list.
But if another thread is at the same time adding a new control
to a request, then there is a race condition where one thread
is removing a control handler object from the requests list and
another thread is adding one. The result is that hdl->requests
is no longer empty and the code thinks that a main handler is
being freed instead of a control handler that is part of a request.
There are two bugs here: first the test for hdl->req_obj.req: this
should be hdl->req_obj.ops since only the main control handler will
have a NULL pointer there.
The second is that adding or deleting request objects from the
requests list of the main handler isn't protected by taking the
main handler's lock.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: John Cox <jc@kynesim.co.uk>
Fixes: 6fa6f831f0 ("media: v4l2-ctrls: add core request support")
Tested-by: John Cox <jc@kynesim.co.uk>
Reported-by: John Cox <jc@kynesim.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
(cherry picked from commit be7e8af98f)
Update the symbol as well as the alias so that other overlays will
then be applied against the right node.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Fixes the following v4l2-compliance failure:
fail: v4l2-test-controls.cpp(871): subscribe event for control 'User Controls' failed test
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Trial and error reveals that the minimum vblank value appears to be 24
(the OV5647 data sheet does not give any clues). This fixes streaming
lock-ups in full resolution mode.
Fixes: 9b5a5ebedc ("media: i2c: ov5647: Add support for V4L2_CID_VBLANK")
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
The top offset in the pixel array is actually 6 (see page 3-1 of the
OV5647 data sheet).
Fixes: f2f7ad5ce5 ("media: i2c: ov5647: Selection compliance fixes")
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
It looks like some displays (like the LG 27UL850-W) don't enable the
scrambling when the HDMI driver enables it. However, if we set later the
scrambler enable bit, the display will work as expected.
Let's create delayed work queue to periodically look at the display
scrambling status, and if it's not set yet try to enable it again.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
DRM currently polls for the HDMI connector status every 10s, which can
be an issue when we connect/disconnect a display quickly or the device
on the other end only issues a hotplug pulse (for example on EDID
change).
Switch the driver to rely on the internal controller logic for the
BCM2711/RPi4.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
When we have the entire DRM state, retrieving the connector state only
requires the drm_connector pointer. Fortunately for us, we have
allocated it as a part of the vc4_hdmi structure, so we can retrieve get
a pointer by simply accessing our field in that structure.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
If the HPD GPIO is not available and drm_probe_ddc fails, we end up
reading the HDMI_HOTPLUG register, but the controller might be powered
off resulting in a CPU hang. Make sure we have the power domain and the
HSM clock powered during the detect cycle to prevent the hang from
happening.
Fixes: 4f6e3d66ac ("drm/vc4: Add runtime PM support to the HDMI encoder driver")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
pm_runtime_get_sync increases the PM usage counter even if it fails, and
forgetting to do so will result in a reference leak. We can't really do
anything in atomic_enable in case of a failure though, and we probably
can't recover either, but at least switching to
pm_runtime_resume_and_get makes us play nice with the PM subsystem.
Fixes: 4f6e3d66ac ("drm/vc4: Add runtime PM support to the HDMI encoder driver")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
At boot, we can't rely on the vc4_get_crtc_encoder since we don't have a
state yet and thus will not be able to figure out which connector is
attached to our CRTC.
However, we have a muxing bit in the CRTC register we can use to get the
encoder currently connected to the pixelvalve. We can thus read that
register, lookup the associated register through the vc4_pv_data
structure, and then pass it to vc4_crtc_disable so that we can perform
the proper operations.
Fixes: 875a4d5368 ("drm/vc4: drv: Disable the CRTC at boot time")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The vc4_get_crtc_encoder function currently only works when the
connector->state->crtc pointer is set, which is only true when the
connector is currently enabled.
However, we use it as part of the disable path as well, and our lookup
will fail in that case, resulting in it returning a null pointer we
can't act on.
We can access the connector that used to be connected to that crtc
though using the old connector state in the disable path.
Since we want to support both the enable and disable path, we can
support it by passing the state accessor variant as a function pointer,
together with the atomic state.
Fixes: 792c3132bc ("drm/vc4: encoder: Add finer-grained encoder callbacks")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The vc4_crtc_config_pv will need to access the drm_atomic_state
structure and its only parent function, vc4_crtc_atomic_enable already
has access to it. Let's pass it as a parameter.
Fixes: 792c3132bc ("drm/vc4: encoder: Add finer-grained encoder callbacks")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
This reverts commit 3cf3d39b75.
This commit was making the assumption that we had a 1:1 mapping between
the encoders and their CRTC. While this is true for the HDMI controllers
on the BCM2711, this isn't true for the other encoders (DSI0 and DPI
share the PixelValve 0, and DSI1 and SMI share the PixelValve1), and
this isn't true at all on the older SoCs, effectively breaking the
encoder retrieval logic.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The current core while setting the min and max rate properly in the
clk_request structure will not make sure that the requested rate is
within these boundaries, leaving it to each and every driver to make
sure it is.
Add a clamp call to make sure it's always done.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The dwc2 gadget support maps and unmaps DMA buffers as necessary. When
mapping and unmapping it uses the direction of the endpoint to select
the direction of the DMA transfer, but this fails for Control OUT
transfers because the unmap occurs after the endpoint direction has
been reversed for the status phase.
A possible solution would be to unmap the buffer before the direction
is changed, but a safer, less invasive fix is to remember the buffer
direction independently of the endpoint direction.
See: https://github.com/raspberrypi/Raspberry-Pi-OS-64bit/issues/127
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
This is a simple overlay based on the simple-audio-card and the dmic
codec. It has the speciality that it is configured to use the codec
as a master I2S device. It works for example with the Si468x DAB
receiver on the uGreen DABBoard.
See: https://github.com/raspberrypi/linux/issues/4304
Signed-off-by: Christoph Orth <c.orth@ugreen.eu>
The 2711 pixel valve can't produce odd horizontal timings, and
checks were added to vc4_hdmi_encoder_atomic_check and
vc4_hdmi_encoder_mode_valid to filter out/block selection of
such modes.
Modes with DRM_MODE_FLAG_DBLCLK double all the horizontal timing
values before programming them into the PV. The PV values,
therefore, can not be odd, and so the modes can be supported.
Amend the filtering appropriately.
See https://github.com/raspberrypi/linux/issues/4307
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Keeping a copy of the old poweroff handler allows it to be restored
should this module be unloaded, but also provides a fallback if the
power hasn't been removed when the timeout elapses.
See: https://github.com/raspberrypi/rpi-eeprom/issues/330
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
There is no reason not to support multiple gpio-shutdown signals,
so add the necessary __override__ magic.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The result of dividing a u32 by a size_t is an unsigned int on arm32
and a long unsigned int on arm64. Use "%zu" (the size_t format) to
remove the build warning for 64-bit builds.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
During decode, setting the CAPTURE queue format was setting the crop
rectangle to the requested height before aligning up the format to
cater for simple clients that weren't expecting to deal with cropping
and the SELECTION API.
This caused problems on some resolution change events if the client
didn't also then use the selection API.
Disable the crop update after a resolution change.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Whilst the hardware can't achieve the limits of level 4.2 under
all situations, it can exceed level 4.0.
Allow selection of levels 4.1 and 4.2.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
MMAL has the flag MMAL_BUFFER_HEADER_FLAG_CORRUPTED but that
wasn't being passed through, so add it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Video decode supports YUV and RGB formats. YUV needs to report SMPTE170M
or REC709 appropriately, whilst RGB should report SRGB.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The driver said it supported H264 levels 4.1 and 4.2, but
was missing the V4L2 to MMAL mappings.
Add in those mappings.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The current code will first dereference the req pointer and then test if
it's NULL, resulting in a NULL pointer dereference if req is indeed
NULL. Reorder the test and derefence to avoid the issue
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The VEC's DAC on BCM2711 is slightly different compared to the one on
BCM283x and needs different configuration. In particular, bit 3
(mask 0x8) switches the BCM2711 DAC input to "self-test input data",
which makes the output unusable. Separating two compatible variants in
devicetrees and the DRM driver was therefore necessary.
The configurations used for both variants have been borrowed from
Raspberry Pi (model 3B for BCM283x, 4B for BCM2711) firmware defaults.
Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
On the BCM2711 (Raspberry Pi 4), the VEC is actually connected to
output 2 of pixelvalve3.
NOTE: This contradicts the Broadcom docs, but has been empirically
tested and confirmed by Raspberry Pi firmware devs.
Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
The VEC has a different address (0x7ec13000) on the BCM2711 (used in
e.g. Raspberry Pi 4) compared to BCM238x (e.g. Pi 3 and earlier). This
was erroneously not taken account for.
Definition of the VEC in the devicetrees had to be moved from
bcm283x.dtsi to bcm2711.dtsi and bcm2835-common.dtsi to allow for this
differentiation.
Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
Extend the spi-rtc overlay to support the ds3232 and ds3234 RTCs, as
well as adding parameters to select difference SPI controllers and
chip selects.
N.B. The default CS is now active-low - use the "cs_high" parameter to
override this.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Now that we have the infrastructure in place, we can raise the maximum
pixel rate we can reach for HDMI0 on the BCM2711.
HDMI1 is left untouched since its pixelvalve has a smaller FIFO and
would need a clock faster than what we can provide to support the same
modes.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The HDMI controller on the BCM2711 includes a scrambler in order to
reach the HDMI 2.0 modes that require it. Let's add the support for it.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
In order to reach the frequencies needed to output at 594MHz, the
firmware needs to be configured with the appropriate parameters in the
config.txt file (enable_hdmi_4kp60 and force_turbo).
Let's detect it at bind time, warn the user if we can't, and filter out
the relevant modes.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The BVB clock rate computation doesn't take into account a mode clock of
594MHz that we're going to need to support 4k60.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
We'll need to have the HVS binding before the HDMI controllers so that
we can check whether the firmware allows to run in 4kp60. Reorder a bit
the component list, and document the current constraints we're aware of.
Acked-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Since we fixed the hooks to disable the encoder at boot, we now have an
unbalanced clk_disable call at boot since we never enabled them in the
first place.
Let's mimic the state of the hardware and enable the clocks at boot if
the controller is enabled to get the use-count right.
Cc: <stable@vger.kernel.org> # v5.10+
Fixes: 09c438139b ("drm/vc4: hdmi: Implement finer-grained hooks")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Due to a FIFO that cannot be flushed between the pixelvalve and the HDMI
controllers on BCM2711, we need to carefully disable both at boot time
if they were left enabled by the firmware.
However, at the time we're running that code, the struct drm_connector
encoder pointer isn't set yet, and thus we cannot retrieve the encoder
associated to our CRTC.
We can however make use of the fact that we have a less flexible setup
than what DRM allows where we have a 1:1 relationship between our CRTCs
and encoders (and connectors), and thus store the crtc associated to our
encoder at boot time.
We cannot do that at the time the encoders are probed though, since the
CRTCs won't be probed yet and thus we don't know at that time which CRTC
index we're going to get, so let's do this in two passes: we can first
bind all the components and then once they all are bound, we can iterate
over all the encoders to find their associated CRTC and set the pointer.
This is similar to what we're doing to set the possible_crtcs field.
Fixes: 875a4d5368 ("drm/vc4: drv: Disable the CRTC at boot time")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The vc4_set_crtc_possible_masks is meant to run over all the encoders
and then set their possible_crtcs mask to their associated pixelvalve.
However, since the commit 39fcb28083 ("drm/vc4: txp: Turn the TXP into
a CRTC of its own"), the TXP has been turned to a CRTC and encoder of
its own, and while it does indeed register an encoder, it no longer has
an associated pixelvalve. The code will thus run over the TXP encoder
and set a bogus possible_crtcs mask, overriding the one set in the TXP
bind function.
In order to fix this, let's skip any virtual encoder.
Cc: <stable@vger.kernel.org> # v5.9+
Fixes: 39fcb28083 ("drm/vc4: txp: Turn the TXP into a CRTC of its own")
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The current code does a binary OR on the possible_crtcs variable of the
TXP encoder, while we want to set it to that value instead.
Cc: <stable@vger.kernel.org> # v5.9+
Fixes: 39fcb28083 ("drm/vc4: txp: Turn the TXP into a CRTC of its own")
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Credit to forum member gizmomouse on
https://www.raspberrypi.org/forums/viewtopic.php?f=98&t=253912 and
Andrey Vostrukhin of Harlab for these overlays.
See https://github.com/harlab/CM4_LCD_LT070ME05000 for
schematics and docs for the adapter board to connect this panel which
is found in the Asus/Google 2013 Nexus 7" tablet and therefore
relatively easily available.
Note that this uses 4 DSI data lanes, and therefore MUST be used
with DISP1 on a Compute Module. It can not be used on a standard
Pi.
There are two versions of the adapter board. V1 connects the
display controls to Pi GPIOs, whilst v2 uses an I2C GPIO expander
so needs no additional connections beyond the FFC and power.
The touchscreen overlay for these panels varies, so that part
is not configured.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
There is no reason why the control GPIOs for the panel can not
be connected to I2C or similar GPIO interfaces that may need to
sleep, therefore switch from gpiod_set_value to
gpiod_set_value_cansleep calls to configure them.
Without that you get complaints from gpiolib every time the state
is changed.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
vc4_dsi_encoder_disable is partially an open coded version of
drm_bridge_chain_disable, but it missed a termination condition
in the loop for ->disable which meant that no post_disable
calls were made.
Add in the termination clause.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
DSI0 seemingly had very little or no testing as a load of
the register mappings were incorrect/missing, so host
transfers always timed out due to enabling/checking incorrect
bits in the interrupt enable and status registers.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
vc4_dsi was registering both dsi0 and dsi1 as VC4_ENCODER_TYPE_DSI1
which seemed to work OK for a single DSI display, but fails
if there are two DSI displays connected.
Update to register the correct type.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
For slightly unknown reasons, dsi0 takes a different pixel format
to dsi1, and that has to be set in the pixel valve.
Amend the setup accordingly.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Replace an undeclared variable used by DWC_DEBUGPL with the real endpoint address. DWC_DEBUGPL does nothing with DEBUG undefined so it did not go wrong before.
Signed-off-by: Zixuan Wang <wangzixuan@sjtu.edu.cn>
commit c2198943e3 upstream.
The vendor mode is not always at config #1, so it is necessary to
set the correct configuration number.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 195aae321c upstream.
Support RTL8153C, RTL8153D, RTL8156A, and RTL8156B. The RTL8156A
and RTL8156B are the 2.5G ethernet.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 67ce1a806f upstream.
The different chips may have different requests when changing mtu.
Therefore, add a new help function of rtl_ops to change mtu. Besides,
reset the tx/rx after changing mtu.
Additionally, add mtu_to_size() and size_to_mtu() macros to simplify
the code.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 5133bcc748 upstream.
Set the maximum inter frame gap time (144ns) for speed 10M/half and
100M/half. It improves the performance for those speeds. And, there
is no effect for the other speeds.
For 10M/half and 100M/half, the fast inter frame gap time let the
device couldn't use the feature of the aggregation effectively,
because the transfer would be completed fastly. Therefore, use the
maximum value to improve the effect of the aggregation. However, you
may not feel the improvement for fast CPUs, because they compensate
for the effect of the aggregation.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 156c320761 upstream.
Some messages are before calling register_netdev(), so replace
netif_err() with dev_err().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
commit c79515e479 upstream.
Return error code if autosuspend_en, eee_get, or eee_set don't exist.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
commit 7a0ae61acd upstream.
U1/U2 shoued be enabled for USB 3.0 or later. The USB 2.0 doesn't
support it.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
commit 80fd850b31 upstream.
For runtime resuming, the RTL8153B may be resumed from the state
of power cut, when enabling the feature of UPS. Then, the PHY
would be reset, so it is necessary to be initailized again.
Besides, the USB_U1U2_TIMER also has to be set again, so I move
it from r8153b_init() to r8153b_hw_phy_cfg().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
commit a08c0d309d upstream.
Replace r8153_patch_request() with rtl_phy_patch_request().
Replace r8153_pre_ram_code() with rtl_pre_ram_code().
Replace r8153_post_ram_code() with rtl_post_ram_code().
Add rtl_patch_key_set().
The new functions have an additional parameter. It is used to wait
the patch request command finished. When the PHY is resumed from
the state of power cut, the PHY is at a safe mode and the
OCP_PHY_PATCH_STAT wouldn't be updated. For this situation, it is
safe to set patch request command without waiting OCP_PHY_PATCH_STAT.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
commit f3163f1cb8 upstream.
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1c ("tasklet: Introduce new initialization API")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
commit c1aedf015e upstream.
Support ECM mode based on cdc_ether with relative mii functions,
when CONFIG_USB_RTL8152 is not set, or the device is not supported
by r8152 driver.
Both r8152 and r8153_ecm would check the return value of
rtl8152_get_version() in porbe(). If rtl8152_get_version()
return none zero value, the r8152 is used for the device
with vendor mode. Otherwise, the r8153_ecm is used for the
device with ECM mode.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/1394712342-15778-392-Taiwan-albertk@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
commit 34e653efb6 upstream.
Fixes the following W=1 kernel build warning(s):
drivers/net/usb/r8152.c:934: warning: Function parameter or member 'blk_hdr' not described in 'fw_mac'
drivers/net/usb/r8152.c:934: warning: Function parameter or member 'reserved' not described in 'fw_mac'
drivers/net/usb/r8152.c:947: warning: Function parameter or member 'blk_hdr' not described in 'fw_phy_patch_key'
drivers/net/usb/r8152.c:947: warning: Function parameter or member 'reserved' not described in 'fw_phy_patch_key'
drivers/net/usb/r8152.c:986: warning: Function parameter or member 'blk_hdr' not described in 'fw_phy_nc'
drivers/net/usb/r8152.c:986: warning: Function parameter or member 'mode_pre' not described in 'fw_phy_nc'
drivers/net/usb/r8152.c:986: warning: Function parameter or member 'mode_post' not described in 'fw_phy_nc'
drivers/net/usb/r8152.c:986: warning: Function parameter or member 'reserved' not described in 'fw_phy_nc'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20201102114512.1062724-23-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The new clock request API allows us to increase the rate of the
core clock as required during mode set while decreasing it when
we're done, resulting in a better power-efficiency.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
The new clock request API allows us to increase the rate of the HSM
clock to match our pixel rate requirements while decreasing it when
we're done, resulting in a better power-efficiency.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
It's not unusual to find clocks being shared across multiple devices
that need to change the rate depending on what the device is doing at a
given time.
The SoC found on the RaspberryPi4 (BCM2711) is in such a situation
between its two HDMI controllers that share a clock that needs to be
raised depending on the output resolution of each controller.
The current clk_set_rate API doesn't really allow to support that case
since there's really no synchronisation between multiple users, it's
essentially a fire-and-forget solution.
clk_set_min_rate does allow for such a synchronisation, but has another
drawback: it doesn't allow to reduce the clock rate once the work is
over.
In our previous example, this means that if we were to raise the
resolution of one HDMI controller to the largest resolution and then
changing for a smaller one, we would still have the clock running at the
largest resolution rate resulting in a poor power-efficiency.
In order to address both issues, let's create an API that allows user to
create temporary requests to increase the rate to a minimum, before
going back to the initial rate once the request is done.
This introduces mainly two side-effects:
* There's an interaction between clk_set_rate and requests. This has
been addressed by having clk_set_rate increasing the rate if it's
greater than what the requests asked for, and in any case changing
the rate the clock will return to once all the requests are done.
* Similarly, clk_round_rate has been adjusted to take the requests
into account and return a rate that will be greater or equal to the
requested rates.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
be suspended
Webcams with microphones are composite devices, and autosuspend is set
at the device level. If uvcvideo is probed after snd-usb-audio, the effect
of the quirk applied by snd-usb-audio is undone by uvcvideo's global
application of autosuspend.
Incrementing the interface's PM refcount in such cases prevents runtime PM
from happening, thus the device is left active.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
These devices use a type of Sonix chipset that produces broken microphone
data if suspended/resumed.
They also don't support readback of the sample rate.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
https://gist.github.com/popcornmix/6b3e23103c60170b02b148e0ba5d6ed7
is the script used to generate the 601, 709 and 2020 colourspaces.
I've regenetated the existing ones using script so it is reprocable
but there are lsb dfferences compared to values here (copied from spec)
whose origin is now lost.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
When importing there was a missing call to detach the buffer,
so each import leaked the sg table entry.
Actually the release process for both locally allocated and
imported buffers is identical, so fix them to both use the same
function.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Our driver while supporting HDR didn't send the proper colorimetry info
in the AVI infoframe.
Let's add the property needed so that the userspace can let us know what
the colorspace is supposed to be.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The intel driver uses the same logic to attach the Colorspace property
in multiple places and we'll need it in vc4 too. Let's move that common
code in a helper.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
All the drivers that support the HDR metadata property have a similar
function to compare the metadata from one connector state to the next,
and force a mode change if they differ.
All these functions run pretty much the same code, so let's turn it into
an helper that can be shared across those drivers.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
All the drivers that implement HDR output call pretty much the same
function to initialise the hdr_output_metadata property, and while the
creation of that property is in a helper, every driver uses the same
code to attach it.
Provide a helper for it as well
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Commit 158e800e0f upstream
A test was added to the probe function to ensure the device was
actually connected and working before successfully completing a
probe. If the device was actually there, but the I2C bus was not
ready yet for whatever reason, the probe fails permanently.
Change the probe so that we defer the probe on a regmap read
failure so that we try the probe again when the dependent drivers
are potentially loaded. This should not affect the case where the
device truly isn't present because the probe will never successfully
complete.
Fixes: 2aa916e67d ("sc16is7xx: Read the LSR register for basic device presence check")
Cc: stable@vger.kernel.org
Signed-off-by: Annaliese McDermond <nh6z@nh6z.net>
Link: https://lore.kernel.org/r/010101787f9c3fd8-c1815c00-2d6b-4c85-a96a-a13e68597fda-000000@us-west-2.amazonses.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add unique names to the individual dac coded drivers
Remove some of the codec controls that are not used.
Signed-off-by: Paul Hermann <paul@picoreplayer.org>
# Conflicts:
# sound/soc/bcm/allo-piano-dac-plus.c
warning: address of array 'desc->wMaxPacketSize' will always evaluate to 'true'
The wMaxPacketSize field is actually a two element array which content should
be accessed via the UGETW macro.
x_off should only be within current stripe
The stripe number is accounted for elsewhere
Fixes: 9b1b1beb1c ("vc4/drm: Fix source offsets with DRM_FORMAT_P030")
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Neither CM4 nor Pi 400 have appeared upstream yet, and as a result
they have missed out on improvements to the Pi 4B platform.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
ARM: dts: Bring bcm2711-rpi-400.dts up-to-date
Pi 400 support has not appeared upstream yet, and as a result it has
missed out on improvements to the other Pi 4 platforms.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
1. Reduce the delay between RELAY1 and RELAY2 to 1000ms.
2. Rename the states to simplify LED control by an external script.
3. Claim all the required GPIOs, enabling pull-ups on the input.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The Adafruit Mini-PiTFT13 display needs offsets applying when rotated,
so use the "variant" mechanism to select a custom set_addr_win method
using a dedicated compatible string of "fbtft,minipitft13".
See: https://github.com/raspberrypi/firmware/issues/1524
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
DMABUFs are all handled by videobuf2, so there is no reason not
to enable support for them.
Note that this driver is still using the vmalloc allocator, so
the buffers it allocates will not be compatible with the codec
or ISP driver that require contiguous buffers. However this
driver should be able to import the buffers allocated by them.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
There is little harm in ignoring fractional coordinates
(they just get truncated).
Without this:
modetest -M vc4 -F tiles,gradient -s 32:1920x1080-60 -P89@74:1920x1080*.1.1@XR24
is rejected. We have the same issue in Kodi when trying to
use zoom options on video.
Note: even if all coordinates are fully integer. e.g.
src:[0,0,1920,1080] dest:[-10,-10,1940,1100]
it will still get rejected as drm_atomic_helper_check_plane_state
uses drm_rect_clip_scaled which transforms this to fractional src coords
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Spec says: bits [31:4] of the given address should point to
the 128-bit word containing the desired starting pixel,
and bits[3:0] should be between 0 and 11, indicating which
of the 12-pixels in that 128-bit word is the first pixel to be used
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Run the PoE hat fan with reduced noise when possible. The PoE hat fan will spin even at PWM=1 and spins almost silent. Tested at 17ºC, the fan PWM alternates between 1 and 10, which is a lot less noisy then alternating between PWM levels 0 and 31.
Without aliases for the new SPI interfaces in BCM2711, spidev instances
will be allocated sequential numbers that may not match the number of
the physical interface.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
In order to accommodate full PCI DMA access to memory on newer BCM2711
revisions, we're forced to map PCIe's view of physical memory with an
offset. This offset makes DMA addressing dependent on having 64bit
support on the PCI device's side. Which isn't always the case.
In order to mitigate this, introduce the pcie-32bit-dma overlay which
will forbid firmware from updating the default inbound memory window.
The default setting, albeit limited to accessing the lower 3GB of
memory, will allow for 32bit DMA addresses at the expense of having to
bounce buffers.
Link: https://github.com/raspberrypi/linux/issues/4197
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Experimentally have found PV on hvs4 reports fifo full
error with expected settings and does not with one less
This appears as:
[drm:drm_atomic_helper_wait_for_flip_done] *ERROR* [CRTC:82:crtc-3] flip_done timed out
with bit 10 of PV_STAT set "HVS driving pixels when the PV FIFO is full"
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
With HBR audio (8 channel 192kHz) we get occasional VC4_HD_MAI_CTL_DLATE error flags in
HDMI_MAI_CTL which seem to correspond with audio dropouts.
Increasing the normal AXI priority for dma is needed to avoid these
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
We are getting occasional VC4_HD_MAI_CTL_ERRORF in
HDMI_MAI_CTL which seem to correspond with audio dropouts.
Reduce the threshold where we deassert DREQ to avoid the fifo overfilling
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
v4l_cropcap calls our vidioc_g_pixelaspect function to get the pixel
aspect ratio, but also calls g_selection for V4L2_SEL_TGT_CROP_BOUNDS
and V4L2_SEL_TGT_CROP_DEFAULT. Whilst it allows for vidioc_g_pixelaspect
not to be implemented, it doesn't allow for either of the other two.
Add in support for the additional selection targets.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
If the format is detected by the driver and a V4L2_EVENT_SOURCE_CHANGE
event is generated, then pass on the pixel aspect ratio as well.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Fixes: "staging/bcm2835-codec: Log the number of excess supported formats"
Which used %u for printing a size_t, and 64bit builds then log a warning.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
In order to get the intended behaviour of the stateful video
decoder API where only the OUTPUT queue needs to be enabled and fed
buffers in order to get the SOURCE_CHANGED event that configures the
CAPTURE queue, we want the device to run should either queue be
streaming.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The recently improved RTC_HCTOSYS option now works with RTC drivers in
modules, making it much more useful in that it removes the need to run
hwclock -s in order to synchronise the system clock.
See: https://github.com/raspberrypi/linux/issues/4205
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The i2c_csi_dsi parameter of the i2c-rtc overlay (added for the CM4IO
board) causes the RTC devices to be probed on the I2C0 bus appearing
on GPIOs 44 and 45. However, it didn't enable the other nodes necessary
for it to work - "dtparam=i2c_vc=on" was also required.
Fix that.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The kernel modules aes-neon-blk and aes-neon-bs perform poorly, at least on
Cortex-A72 without crypto extensions. In fact, aes-arm64 outperforms them
on benchmarks, despite it being a simpler implementation (only accelerating
the single-block AES cipher).
For modes of operation where multiple cipher blocks can be processed in
parallel, aes-neon-bs outperforms aes-neon-blk by around 60-70% and aes-arm64
is another 10-20% faster still. But the difference is even more marked with
modes of operation with dependencies between neighbouring blocks, such as
CBC encryption, which defeat parallelism: in these cases, aes-arm64 is
typically around 250% faster than either aes-neon-blk or aes-neon-bs.
The key trade-off with aes-arm64 is that the look-up tables are situated in
RAM. This leaves them potentially open to cache timing attacks. The two other
modules, by contrast, load the look-up tables into NEON registers and so are
able to perform in constant time.
This patch aims to load aes-arm64 more often.
If none of the currently-loaded crypto modules implement a given algorithm,
a new one is typically selected for loading using a platform-neutral alias
describing the required algorithm. To enable users to still
load aes-neon-blk or aes-neon-bs if they really want them, while still
ensuring that aes-arm64 is usually selected, remove the aliases from
aes-neonbs-glue.c and aes-glue.c and apply them to aes-cipher-glue.c, but
still build the two NEON modules.
Since aes-glue.c can also be used to build aes-ce-blk, leave them enabled
if USE_V8_CRYPTO_EXTENSIONS is defined, to ensure they are selected if we
in future use a CPU which has the crypto extensions enabled.
Note that the algorithm priority specifiers are unchanged, so if
aes-neon-bs is loaded at the same time as aes-arm64, the former will be
used in preference. However, aes-neon-blk and aes-arm64 have tied priority,
so whichever module was loaded first will be used (assuming aes-neon-bs is
not loaded).
Signed-off-by: Ben Avison <bavison@riscosopen.org>
If multiple sets of interrupts occur simultaneously, it may be unsafe
to swap buffers, as the hardware may already be re-using the current
buffers. In such cases, avoid swapping buffers, and wait for the next
opportunity at the Frame End interrupt to signal completion.
Additionally, check the packet compare status when watching for frame
end for buffers swaps, as this could also signify a frame end event.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
This reverts commit 92516cd97f.
Thi commit "Bluetooth: Always request for user confirmation for Just
Works" prevents BLE devices pairing in (at least) the Raspberry Pi OS
GUI. After reverting it, pairing works again.
If another solution to the problem is found then this reversion will
be removed.
See: https://github.com/raspberrypi/linux/issues/4139
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
This reverts commit ffee202a78.
The commit "Bluetooth: Always request for user confirmation for Just
Works" prevents BLE devices pairing in (at least) the Raspberry Pi OS
GUI. After reverting it, pairing works again. Although this companion
commit ("... (LE SC)") has not been demonstrated to be problematic,
it follows the same logic and therefore could affect some use cases.
If another solution to the problem is found then this reversion will
be removed.
See: https://github.com/raspberrypi/linux/issues/4139
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The struct imx477 *ctrl parameter is not used in the function
imx477_adjust_exposure_range(), so remove it.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
The only field in this struct that is used is the format code, so
replace the struct with this single field.
Save the format code in imx477_set_pad_format() when setting up a new
mode so that imx477_get_pad_format() performs the right lookup.
Otherwise, this caused a bug where the mode lookup occurred on the
12-bit table rather than the 10-bit table.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
The existing 1012x760 120 fps mode has significant IQ problem using
the internal sensor scaler. Replace this mode with a 1332x990 120 fps
mode instead. This new mode has a smaller field of view, but does not
suffer from the bad IQ of the original mode.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
When vblank changes we must modify the exposure range. Also, with this
sensor, the effective exposure time implicitly changes when vblank
does, so we have to reset it after every vblank update.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Add support for very long exposures by using the exposure multiplier
register. Userland does not need to pass any additional controls to
enable long exposures, it simply requests a larger vblank to extend the
exposure control range appropriately.
Currently, since hblank is fixed, a maximum of approximately 124 seconds
of exposure time can be used. In a future change, hblank could also be
controlled in userland to give over 200 seconds of exposure time.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
The V4L2_CID_EXPOSURE_AUTO_PRIORITY was used to let the sensor control
frame length (effectively framerate) based on the requested exposure
time requested. Remove this feature as it is never used, and goes
against how V4L2 likes to handle exposure and vblank controls.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
If the shutdown process is delayed enough to trigger the shutdown
timeout then one or more states in the shutdown sequence might be
skipped. Ensure that all LEDs are turned off regardless by explicitly
doing so in the shutdown state, as an example of good practices.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The driver is intended to jump directly to a shutdown state in the
event of a timeout during shutdown, but the sense of the test was
inverted.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Add gpio-fsm sysfs entries under /sys/class/gpio-fsm. For each state
machine show the current state, which state (if any) will be entered
after a delay, and the current value of that delay.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
DPI hasn't really been used up until now, so the default has
been meaningless.
In theory we should be able to pass the desired format for the
adjacent bridge chip through, but framework seems to be missing
for that.
As the main device to use DPI is the VGA666 or Adafruit Kippah,
both of which use RGB666, change the default to being RGB666 instead
of RGB888.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
VGA666 uses "vga-connector" from DRM_DISPLAY_CONNECTOR, and
"dumb-vga-dac" from DRM_SIMPLE_BRIDGE to connect up, so add them
to the defconfigs.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
VGA666 doesn't use the DE or PCLK signals, therefore there is
no point in claiming their use. It's also then possible to
use GPIOs 0&1 for DDC to read the EDID from the display.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
If realloc to increase coeff size fails then attempt to re-allocate
the original size. If that also fails then flag a fatal error to abort
all further decode.
Signed-off-by: John Cox <jc@kynesim.co.uk>
According to CTA-861 specification, HDR static metadata data block allows a
sink to indicate which HDR metadata types it supports by setting the SM_0 to
SM_7 bits. Currently, only Static Metadata Type 1 is supported and this is
indicated by setting the SM_0 bit to 1.
However, the connector->hdr_sink_metadata.hdmi_type1.metadata_type is always
0, because hdr_metadata_type() in drm_edid.c checks the wrong bit.
This patch corrects the HDMI_STATIC_METADATA_TYPE1 bit position.
Signed-off-by: Laurentiu Palcu <laurentiu.palcu@nxp.com>
The gpio-fsm property "num-soft-gpios" triggers a kernel DT checker
that warns about the lack of #gpio-cells on a random node with the
phandle that just happens to match the number of soft GPIOs. Rename
the property to "num-swgpios" to avoid the warning.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
As of 5.10, the Device Tree parser warns about properties that look
like references to "suppliers" of various services. "num-soft-gpios"
resembles a declaration of a GPIO called "num-soft", causing the value
to be interpreted as a phandle, the owner of which is checked for a
"#gpio-cells" property.
To avoid this warning, rename the gpio-fsm property to "num-swgpios".
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
This reverts commit 93a3b097c4.
GIC interrupt 117 is shared with the HDMI interrupt controller
and all the standard BSC I2C controllers. Whilst the BSC driver
flags the interrupt as shared, there doesn't appear to be an
easy way to flag the controller as being on a shared parent
interrupt.
Revert to polling the I2C controllers.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Adds 2 msecs delay when switching between oscillators to allow
correct PLL settling.
Thanks to Clive Messer for the support!
Signed-off-by: Joerg Schambacher <joerg@hifiberry.com>
Each supported format now includes a mask showing the allowed colour
spaces, as well as a default colour space for when one was not
specified.
Additionally we translate the colour space to mmal format and pass it
over to the VideoCore.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
The cherry-pick of the patch that added the greyworld AWB mode
was incomplete. Fix it up.
Fixes: b3ef481fe2 "staging: bcm2835-camera: Add greyworld AWB mode"
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Unlike the previous generations, the HSM clock limitation is way above
what we can reach without scrambling, so let's move the maximum
frequency we support to the maximum clock frequency without scrambling.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The CEC and hotplug interrupts go through an interrupt controller shared
between the two HDMI controllers.
Let's add that interrupt controller and the interrupts for both HDMI
controllers
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The BSC controllers used for the HDMI DDC have an interrupt controller
shared between both instances. Let's add it to avoid polling.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The CEC and hotplug interrupts were missing when that binding was
introduced, let's add them in now that we've figured out how it works.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
We introduced the BCM2711 support to the vc4 HDMI controller with 5.10,
but this was lacking any of the interrupts of the CEC controller so we
have to deal with the backward compatibility.
Do so by simply ignoring the CEC setup if the DT doesn't have the
interrupts property.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The HDMI controller found in the BCM2711 has an external interrupt
controller for the CEC and hotplug interrupt shared between the two
instances.
Let's add a variant flag to register a single interrupt handler and
deals with the interrupt handler setup, or two interrupt handlers
relying on an external irqchip.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The BCM2711 has two different interrupt sources to transmit and receive
CEC messages, provided through an external interrupt chip shared between
the two HDMI interrupt controllers.
The rest of the CEC controller is identical though so we need to change
a bit the code organisation to share the code as much as possible, yet
still allowing to register independant handlers.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
While the BCM2835 had the CEC clock derived from the HSM clock, the
BCM2711 has a dedicated parent clock for it.
Let's introduce a separate clock for it so that we can handle both
cases.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
As part of the enable sequence we might change the HSM clock rate if the
pixel rate is different than the one we were already dealing with.
On the BCM2835 however, the CEC clock derives from the HSM clock so any
rate change will need to be reflected in the CEC clock divider to output
40kHz.
Fixes: cd4cb49dc5 ("drm/vc4: hdmi: Adjust HSM clock rate depending on pixel rate")
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The CEC clock divider needs to output a frequency of 40kHz from the HSM
rate on the BCM2835. The driver used to have a fixed frequency for it,
but that changed for the BCM2711 and we now need to compute it
dynamically to maintain the proper rate.
Fixes: cd4cb49dc5 ("drm/vc4: hdmi: Adjust HSM clock rate depending on pixel rate")
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Currently we call cec_phys_addr_invalidate on a hotplug deassert.
That may be due to a TV power cycling, or an AVR being switched
on (and switching edid).
This makes CEC unusable since our controller wouldn't have a physical
address anymore.
Set it back up again on the hotplug assert.
Fixes: 15b4511a4a ("drm/vc4: add HDMI CEC support")
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The commit 311e305fdb ("drm/vc4: hdmi: Implement a register layout
abstraction") forgot one CEC register, and made a copy and paste mistake
for another one. Fix those mistakes.
Fixes: 311e305fdb ("drm/vc4: hdmi: Implement a register layout abstraction")
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The code prior to 311e305fdb ("drm/vc4: hdmi: Implement a register
layout abstraction") was relying on the fact that the register offset
was incremented by 4 for each readl call. That worked since the register
width is 4 bytes.
However, since that commit the HDMI_READ macro is now taking an enum,
and the offset doesn't increment by 4 but 1 now. Divide the index by 4
to fix this.
Fixes: 311e305fdb ("drm/vc4: hdmi: Implement a register layout abstraction")
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The hdmi reset got moved to a later point in the commit 9045e91a47
("drm/vc4: hdmi: Add reset callback").
However, the reset now occurs after vc4_hdmi_cec_init and so tramples
the setup of registers like HDMI_CEC_CNTRL_1
This only affects pi0-3 as on pi4 the cec registers are in a separate
block
Fixes: 9045e91a47 ("drm/vc4: hdmi: Add reset callback")
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The BCM2711 has a number of instances of interrupt controllers handled
by the driver behind the BRCMSTB_L2_IRQ Kconfig option (irq-brcmstb-l2).
Let's select that driver as part of the ARCH_BCM2835 Kconfig option.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Under certain circumstance the DONE flag can appear to be set early.
Fortunately the TA flag is often still set at that time, and it can be
used as an indication that DONE is invalid.
Handle the other cases - when TA is not set but not all data is
available - by silently accepting it and hoping for a second DONE.
See: https://github.com/raspberrypi/linux/issues/3064
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The number is only a hint, but may as well be correct.
Fixes: 471e0029e9 ("media: i2c: imx290: Convert HMAX setting into V4L2_CID_HBLANK")
Fixes: be0b9b7ad1 ("media: i2c: imx290: Add support for V4L2_CID_VBLANK")
Fixes: 8483f0d759 ("media: i2c: imx290: Add exposure control to the driver.")
Fixes: 9764f3459c ("media: i2c: imx290: Add H and V flip controls")
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Most software (including libcamera) requires V4L2_CID_ANALOGUE_GAIN,
not V4L2_CID_GAIN.
The range for the control is 0 to 100 for which the sensor uses only
analogue gain; higher values would involve digital gain which this
control should not apply.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Adds the necessary GPIO handling and ALSA mixer extensions.
Also fixes a problem with the PLL/CLK control when switching sample rates.
Thanks to Clive Messer for the support!
Signed-off-by: Joerg Schambacher <joerg@hifiberry.com>
Commit 0a038c1c29 ("drm/vc4: Move LBM creation out of
vc4_plane_mode_set()") changed the LBM allocation logic from first
allocating the LBM memory for the plane to running mode_set,
adding a gap in the LBM, and then running the dlist allocation filling
that gap.
The gap was introduced by incrementing the dlist array index, but was
never checking whether or not we were over the array length, leading
eventually to memory corruptions if we ever crossed this limit.
vc4_dlist_write had that logic though, and was reallocating a larger
dlist array when reaching the end of the buffer. Let's share the logic
between both functions.
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: Eric Anholt <eric@anholt.net>
Fixes: 0a038c1c29 ("drm/vc4: Move LBM creation out of vc4_plane_mode_set()")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Much effort has been put into finding ways to avoid warnings from dtc
about overlays, usually to do with the presence of #address-cells and
size-cells, but not exclusively so. Since the issues being warned about
are harmless, suppress the warnings to declutter the build output and
to avoid alarming users.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
A relatively recent commit ([1]) contained optimisation for the PIO
SPI FIFO-filling functions. The commit message includes the phrase
"[t]he blind and counted loops are always called with nonzero count".
This is technically true, but it is still possible for count to become
zero before the loop is entered - if tfr->len is zero. Moving the loop
exit condition to the end of the loop saves a few cycles, but results
in a near-infinite loop should the revised count be zero on entry.
Strangely, zero-lengthed transfers aren't filtered by the SPI framework
and, even more strangely, the Python3 spidev library is triggering them
for no obvious reason.
Avoid the problem completely by bailing out of the main transfer
function early if trf->len is zero, although there may be a case for
moving the mitigation into the framework.
See: https://github.com/raspberrypi/linux/issues/4100
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
[1] 26751de25d ("spi: bcm2835: Micro-optimise FIFO loops")
RPi4's co-processor will copy the board's bootloader[1] configuration
into memory for the OS to consume. Specifically, for the bootloader
configuration and upgrade user-space routines to query it through
nvmem's sysfs interface.
Introduce a reserved-memory area template for the co-processor to edit
before booting the system so as for Linux not to overwrite that memory
and to expose it as an nvmem device.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
[1] https://www.raspberrypi.org/documentation/hardware/raspberrypi/bcm2711_bootloader_config.md
---
Changes since v1:
- Introduce compatible string
- Change alias name to something more explicit
Firmware/co-processors might use reserved memory areas in order to pass
data stemming from an nvmem device otherwise non accessible to Linux.
For example an EEPROM memory only physically accessible to firmware, or
data only accessible early at boot time.
In order to expose this data to other drivers and user-space, the driver
models the reserved memory area as an nvmem device.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
---
Changes since v1:
- Remove reserved memory phandle indirection by directly creating a
platform device from the reserved memory DT node
- Only map memory upon reading it to avoid corruption
- Small cosmetic cleanups
Firmware/co-processors might use reserved memory areas in order to pass
data stemming from an nvmem device otherwise non accessible to Linux.
For example an EEPROM memory only physically accessible to firmware, or
data only accessible early at boot time.
Introduce the dt-bindings to nvmem's rmem.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
---
Changes since v1:
- Update schema to new driver design
Add colour denoise control to the bcm2835 driver through a new v4l2
control: V4L2_CID_USER_BCM2835_ISP_CDN.
Add the accompanying MMAL configuration structure definitions as well.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
The arm64 version of bcm2711_defconfig is intended for Pi 4, but the
Raspberry Pi OS kernel8.img built from it is also used for Pi 3. It is
therefore necessary to include some legacy drivers such as the BCM2835
thermal driver, otherwise there is no support for reading the CPU
temperature on a Pi 3 in 64-bit mode.
See: https://github.com/raspberrypi/linux/issues/4077
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
LBM base address is measured in units of pixels per cycle.
That is 4 for 2711 (hvs5) and 2 for 2708.
We are wasting 75% of lbm by indexing without the scaling.
But we were also using too high a size for the lbm resulting
in partial corruption (right hand side) of vertically
scaled images, usually at 4K or lower resolutions with more layers.
The physical RAM of LBM on 2711 is 8 * 1920 * 16 * 12-bit
(pixels are stored 12-bits per component regardless of format).
The LBM adress indexes work in units of pixels per clock,
so for 4 pixels per clock that means we have 32 * 1920 = 60K
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
This reverts commit 1c15edc0dca002c8536e9f1f5e1ec43017815018.
This revert and its neighbour are opposites. When squashing, delete
the original commits as well.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
It turns out the used CAN SPI chip is not a good way to identify the version of
the CAN HAT.
There are two different board layouts of the Seeed Studio CAN BUS FD HAT. The
v1 board doesn't have a battery holder, while the v2 board has. Update the
overlay README accordinly.
Link: https://github.com/Seeed-Studio/seeed-linux-dtoverlays/issues/13
Cc: Patrick Menschel <menschel.p@posteo.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Update those overlays that use the regulator framework to use the
new cam1_reg node to control the camera shutdown line, and remove
the firmware workaround nodes.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The current firmware fixup of camera sensor overlays is not
particularly nice, and it stops you being able to load them
dynamically.
It's also incompatible with creating a simple DT that can be
loaded for both CAM1 and CAM0 on a CM as they would both
try to claim the one GPIO.
Almost all sensors have a hook of some form for a regulator, so
it's relatively straightforward to convert them all to use a
fixed regulator with GPIO control.
Add a fixed regulator node for each platform with the GPIO
correctly configured for the camera shutdown line. (The LED line
is ignored).
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
This patch adds the overlay for the Seeed Studio CAN BUS FD HAT v1 with two CAN
FD Channels (based on mcp2517fd).
https://www.seeedstudio.com/2-Channel-CAN-BUS-FD-Shield-for-Raspberry-Pi-p-4072.html
The overlay was generated by:
ovmerge -c spi1-1cs-overlay.dts,cs0_pin=18,cs0_spidev=false \
mcp251xfd-overlay.dts,spi0-0,interrupt=25 \
mcp251xfd-overlay.dts,spi1-0,interrupt=24
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There are several versions of the Seeed Studio CAN BUS FD HAT. This is the
second version, based on the mcp2518fd, so give it a -v2 postfix.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
To comply with the intended usage of the V4L2 selection target when
used to retrieve a sensor image properties, adjust the rectangles
returned by the ov5647 driver.
The top/left crop coordinates of the TGT_CROP rectangle were set to
(0, 0) instead of (16, 16) which is the offset from the larger physical
pixel array rectangle. This was also a mismatch with the default values
crop rectangle value, so this is corrected. Found with v4l2-compliance.
While at it, add V4L2_SEL_TGT_CROP_BOUNDS support: CROP_DEFAULT and
CROP_BOUNDS have the same size as the non-active pixels are not readable
using the selection API. Found with v4l2-compliance.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Use (reserved) bits 24 and 25 of the dreq value
(the second cell of the DT DMA descriptor) to request
that wide source reads or wide dest writes are required
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
When logging that the firmware has provided more supported formats
than we had allocated storage for, log the number allocated and
returned.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Now that the firmware supports the unpacked (16bpp) variants
of the MIPI raw formats, add the mappings.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
When logging that the firmware has provided more supported formats
than we had allocated storage for, log the number allocated and
returned.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Now that the firmware supports the unpacked (16bpp) variants
of the MIPI raw formats, add the mappings.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Support has been added for the unpacked (16bpp) versions of
the MIPI raw 10, 12, and 14 formats, so add the 4CCs for them.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
For some reason lost in history function vchiq_mmal_init used
a static variable for storing the vchiq_instance.
This value is retrieved from vchiq per instance, so worked fine
until you try to call vchiq_mmal_init multiple times concurrently
when things then go wrong. This seemed to happen quite frequently
if using the cutdown firmware (no MMAL or VCSM services running)
as the vchiq_connect then failed, and one or other vchiq_shutdown
was working on an invalid handle.
Remove the static so that each caller gets a unique vchiq_instance.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The recent change to the bulk transfer compat function missed the fact
the relevant ioctl command is VCHIQ_IOC_QUEUE_BULK_TRANSMIT32, not
VCHIQ_IOC_QUEUE_BULK_TRANSMIT, as any attempt to send a bulk block
to the VPU would have shown.
Fixes: a4367cd2b2 ("staging: vchiq: convert compat bulk transfer")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
error logs:
drivers/staging/vc04_services/vc-sm-cma/Kconfig:1:error: recursive dependency detected!
drivers/staging/vc04_services/vc-sm-cma/Kconfig:1: symbol BCM_VC_SM_CMA is selected by BCM2835_VCHIQ_MMAL
drivers/staging/vc04_services/vchiq-mmal/Kconfig:1: symbol BCM2835_VCHIQ_MMAL depends on BCM2835_VCHIQ
drivers/staging/vc04_services/Kconfig:14: symbol BCM2835_VCHIQ is selected by BCM_VC_SM_CMA
For a resolution refer to Documentation/kbuild/kconfig-language.rst
subsection "Kconfig recursive dependency limitations"
Tested-by: make ARCH=arm64 bcm2711_defconfig
Test platform: fedora 33
Branch: rpi-5.10.y
This patch adds the overlay for the Seeed Studio CAN BUS FD HAT
with two CAN FD Channels and an RTC.
https://www.seeedstudio.com/CAN-BUS-FD-HAT-for-Raspberry-Pi-p-4742.html
The overlay was generated by
ovmerge -c mcp251xfd-overlay.dts,spi0-0,interrupt=25 \
mcp251xfd-overlay.dts,spi0-1,interrupt=24 \
i2c-rtc-overlay.dts,pcf85063
Also, add description on how to generate overlays
Signed-off-by: Patrick Menschel <menschel.p@posteo.de>
The addition of the local 'userdata' pointer to
vchiq_irq_queue_bulk_tx_rx omitted the case where neither BLOCKING nor
WAITING modes are used, in which case the value provided by the
caller is replaced with a NULL.
Fixes: 4184da4f31 ("staging: vchiq: fix __user annotations")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The BCM2711 supports higher bpc count than just 8, so let's support it in
our driver.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Unlike the previous generations, the HSM clock limitation is way above
what we can reach without scrambling, so let's move the maximum
frequency we support to the maximum clock frequency without scrambling.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The PHY initialisation parameters are not based on the pixel clock but
the TMDS clock rate which can be the pixel clock in the standard case,
but could be adjusted based on some parameters like the bits per color.
Since the TMDS clock rate is stored in our custom connector state
already, let's reuse it from there instead of computing it again.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The pixel rate is for now quite simple to compute, but with more features
(30 and 36 bits output, YUV output, etc.) will depend on a bunch of
connectors properties.
Let's store the rate we have to run the pixel clock at in our custom
connector state, and compute it in atomic_check.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
When run with a higher bpc than 8, the clock of the HDMI controller needs
to be adjusted. Let's create a connector state that will be used at
atomic_check and atomic_enable to compute and store the clock rate
associated to the state.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm_atomic_helper_connector_reset uses kmalloc which, from an API
standpoint, can fail, and thus setting connector->state to NULL.
However, our reset hook then calls drm_atomic_helper_connector_tv_reset
that will access connector->state without checking if it's a valid
pointer or not.
Make sure we don't end up accessing a NULL pointer.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Suggested-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Commit 63495f6b4a ("drm/vc4: hdmi: Make sure our clock rate is within
limits") was intended to compute the pixel rate to make sure we remain
within the boundaries of what the hardware can provide.
However, unlike what mode_valid was checking for, we forgot to take
into account the clock doubling flag that can be set for modes. Let's
honor that flag if it's there.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reported-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Fixes: 63495f6b4a ("drm/vc4: hdmi: Make sure our clock rate is within limits")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
We'll need to access the connector state in our encoder setup, so let's
just pass the whole DRM state to our private encoder hooks.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Since the CRTC setup in vc4 is split between the PixelValves/TXP and the
HVS, only the PV/TXP atomic hooks were updated in the previous commits, but
it makes sense to update the HVS ones too.
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
It appears that the V4L2 M2M framework requires the driver to manually
call vb2_clear_last_buffer_dequeued on the CAPTURE queue during a
V4L2_DEC_CMD_START.
Add such a call.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Control V4L2_CID_MPEG_VIDEO_HEADER_MODE controls whether the encoder
is meant to emit the header bytes as a separate packet or with the
first encoded frame.
Add support for it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
To comply with the intended usage of the V4L2 selection target when
used to retrieve a sensor image properties, adjust the rectangles
returned by the imx477 driver.
The top/left crop coordinates of the TGT_CROP rectangle were set to
(0, 0) instead of (8, 16) which is the offset from the larger physical
pixel array rectangle. This was also a mismatch with the default values
crop rectangle value, so this is corrected. Found with v4l2-compliance.
While at it, add V4L2_SEL_TGT_CROP_BOUNDS support: CROP_DEFAULT and
CROP_BOUNDS have the same size as the non-active pixels are not readable
using the selection API. Found with v4l2-compliance.
This commit mirrors 543790f777 done for
the imx219 sensor.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
The overlays for the ads1015 and ads1115 I2C ADCs omitted the addresses
in the main device node names. As well as breaking the conventions for
I2C devices, this prevents the firmware from renaming them when the
"reg" property is modified, which in turn stops the overlays from being
instantiated multiple times.
See: https://www.raspberrypi.org/forums/viewtopic.php?f=107&t=294465
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Eric's view was that there was no point in having zpos
support on vc4 as all the planes had the same functionality.
Can be later squashed into (and fixes):
drm/vc4: Add firmware-kms mode
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
The mpu6050 starts up at address 0x68 by default, but can be set to
0x69 if the ADO pin is pulled high. Give the overlay an addr parameter
to allow devices at the alternate address to be used.
See: https://github.com/Hexxeh/rpi-firmware/issues/252
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
lan78xx_link_reset explicitly clears the MAC's view of the PHY's IRQ
status. In doing so it potentially leaves the PHY with a pending
interrupt that will never be acknowledged, at which point no further
interrupts will be generated.
Avoid the problem by acknowledging any pending PHY interrupt after
clearing the MAC's status bit.
See: https://github.com/raspberrypi/linux/issues/2937
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The firmware by default tries to ensure that decoded frame
timestamps always increment. This is counter to the V4L2 API
which wants exactly the OUTPUT queue timestamps passed to the
CAPTURE queue buffers.
Disable the firmware option.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Add support for the PCF85063 and PCF85063A RTC devices to the
i2c-rtc overlay.
Also enable the device to be used on i2c0 (i2c_vc) on GPIOs 0&1 (use
parameter "i2c0") and GPIOs 44 & 45 (use parameter "i2c_csi_dsi").
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Although the BRCMSTB PCIe interface doesn't technically support the
MSI-X spec, in practise it seems to work provided no more than 32
MSI-Xs are required. Add the required flag to the driver to allow
experimentation with devices that demand MSI-X support.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Commit 65e08c4650 failed to clear the
clock state when the device stopped streaming. Fix this, as it might
again cause the same problems when doing an unprepare.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
clk_disable_unprepare() is called unconditionally in stop_streaming().
This is incorrect in the cases where start_streaming() fails, and
unprepares all clocks as part of the failure cleanup. To avoid this,
ensure that clk_disable_unprepare() is only called in stop_streaming()
if the clocks are in a prepared state.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
On a failure in start_streaming(), the error code would not propagate to
the calling function on all conditions. This would cause the userland
caller to not know of the failure.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
The DSI1_PHY_AFEC0_PD_DLANE1 and DSI1_PHY_AFEC0_PD_DLANE3 register
definitions were swapped, so trying to use more than a single data
lane failed as lane 1 would get powered down.
(In theory a 4 lane device would work as all lanes would remain
powered).
Correct the definitions.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The hdmi reset got moved to a later point in
"drm/vc4: hdmi: Add reset callback"
which now occurs after vc4_hdmi_cec_init
and so tramples the setup of registers like
HDMI_CEC_CNTRL_1
This only affects pi0-3 as on pi4 the cec
resgisters are in a separate block
Fixes: ed9a1f6eb4
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
BCM2711 DSI1 doesn't have the issue with the ARM not being
able to write to the registers, therefore remove the DMA
workaround for that compatible string.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
DSI1 on BCM2711 doesn't require the DMA workaround that is used
on BCM2835/6/7, therefore it needs a new compatible string.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
DSI0 was partially supported, but didn't register with the main
driver, and the code was inconsistent as to whether it checked
port == 0 or port == 1.
Add compatible string and other support to make it consistent.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Breaks out common register set and adds the different registers
for 1280x720 (cropped) and 640x480 (skipped) modes
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
CONFIG_BRIDGE_NETFILTER=m used to be the default when CONFIG_NETFILTER
was enabled, but that was removed in 5.9. The way that defconfigs work
caused this wanted setting to be lost in rpi-5.9.y and rpi-5.10.y -
restore it now.
See: https://github.com/Hexxeh/rpi-firmware/issues/248
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The CAN_ISOTP setting was in the wrong position, and it's better for
bisecting and reverting if this doesn't get rolled into the next
config-changing commit.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
In switching to the hardware I2C controller there is an issue
where we seem to not get back the correct state from the Pi
touchscreen.
Insert a delay before polling to avoid this condition.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
We now have the hardware I2C controller pinmuxed to the drive the
display I2C, but this controller does not support clock stretching.
The Atmel micro-controller in the panel requires clock stretching
to allow it to prepare any data to be read.
Split the rpi_touchscreen_i2c_read into two independent transactions with
a delay between them for the Atmel to prepare the data.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
This touchscreen controller is used by the 7" DSI panel, and
this overlay configures it for when it is NOT being polled by
the firmware.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Not all systems have the interrupt line wired up, so switch to
polling the touchscreen off a timer if no interrupt line is
configured.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Using a hdmi analyser the bytes in packet ram
registers beyond the length were visible in the
infoframes and it flagged the checksum as invalid.
Zeroing unused words of packet RAM avoids this
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
[1] replaced a single reset function with a pointer to one of two
implementations, but also removed the call asserting the reset
at the start of brcm_pcie_setup. Doing so breaks Raspberry Pis with
VL805 XHCI controllers lacking dedicated SPI EEPROMs, which have been
used for USB booting but then need to be reset so that the kernel
can reconfigure them. The lack of a reset causes the firmware's loading
of the EEPROM image to RAM to fail, breaking USB for the kernel.
See: https://www.raspberrypi.org/forums/viewtopic.php?p=1758157#p1758157
Fixes: 04356ac307 ("PCI: brcmstb: Add bcm7278 PERST# support")
[1] 04356ac307 ("PCI: brcmstb: Add bcm7278 PERST# support")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
* Add mcp251xfd driver module to the RPi kernel builds.
* Add isotp can protocol module to the RPi kernel builds.
Signed-off-by: Patrick Menschel <menschel.p@posteo.de>
The enable_headphones parameter of the snd_bcm2835 module is forced
to 1 if enable_compat_alsa is 0, so setting them both on the kernel
command line is pointless (and, in the case of Pi 400 and Pi Zeroes,
confusing).
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The sdtweak overlay has been superseded by the board-specific
sd_* parameters such as sd_poll_once, sd_overclock etc.
For example, replace:
dtoverlay=sdtweak,poll_once
with:
dtparam=sd_poll_once
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The last nibble is a revision ID, and the 54213pe is a later rev
than the 54210e. Running the 54210e setup code on a 54213pe results
in a broken RGMII interface.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Define a new mailbox (SET_REBOOT_FLAGS) which may be used to
pass optional flags to the Raspberry Pi firmware that changes
the behaviour of the bootloader and firmware during a reboot.
Currently this just defines the 'tryboot' flag which causes
the firmware to load tryboot.txt instead config.txt. This
alternate configuration file can be used to specify the
path of an alternate firmware and kernels allowing a fallback
mechanism to be implemented for OS upgrades.
Delete a large amount of unused declaration from "usb.h", some of which
were causing build warnings, and get the module building cleanly.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
RASPBERRYPI_FIRMWARE was missing from the arm64 bcm2711_defconfig.
bcmrpi3_defconfig was also missing a few options. Add the misssing
settings and regenerate all the Pi defconfigs.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Attempts to connect external GPUs to Compute Module 4's PCIe bus have
highlighted that the existing "outbound window" - the fraction of the
PCI address base that is appears in the host's memory map - is
restrictively small. Expand the window to a full 1GB.
See: https://www.raspberrypi.org/forums/viewtopic.php?f=98&t=288902
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Add a property to allow the headphone output to be disabled. Use an
integer property rather than a boolean so that an overlay can clear it.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The VL805 controller can't cope with the TR Dequeue Pointer for an endpoint
being set to a Link TRB. The hardware-maintained endpoint context ends up
stuck at the address of the Link TRB, leading to erroneous ring expansion
events whenever the enqueue pointer wraps to the dequeue position.
If the search for the end of the current TD and ring cycle state lands on
a Link TRB, move to the next segment.
See: https://github.com/raspberrypi/linux/issues/3919
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
With vc4-drv node not being under /soc on Pi4, we need to
adopt the correct DMA parameters from a suitable sub-component.
Add "brcm,bcm2711-hvs" to that list of components.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The upstream driver is checking the link frequency parameter, and
the overlay had the wrong value.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Composite gets enabled automatically if HDMI isn't detected,
which can cause some grief in X should it be not connected
and touchscreens are in use.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The upstream bcm2837.dtsi uses cortex-a53-pmu, so we can do the same
but with a fallback to the cortex-a7-pmu which is supported by the
32-bit kernel.
Now that we're using the natural fallback mechanism of compatible
strings, the RPI364 macro no longer serves any purpose - remove it.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The vc5 HDMI registers hadn't been added into the debugfs
register sets, therefore weren't dumped on request.
Add them in.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The order of precedence should be:
- hotplug GPIO being defined
- DDC probe
- hotplug register
In particular the hotplug register is not valid if a GPIO is defined
(eg on Pi0-3), but was being checked.
Fixes "943f078 vc4: cec: Restore cec physical address on reconnect"
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The gpio-fsm driver implements simple state machines that allow GPIOs
to be controlled in response to inputs from other GPIOs - real and
soft/virtual - and time delays. It can:
+ create dummy GPIOs for drivers that demand them,
+ drive multiple GPIOs from a single input, with optional delays,
+ add a debounce circuit to an input,
+ drive pattern sequences onto LEDs
etc.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Overlays are unable to remove properties in the base DTB, but they
can overwrite them. Allow a present but empty 'dmas' property
to also disable the HDMI audio interface.
See: https://github.com/raspberrypi/linux/issues/2489
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Driver for the BCM2835 ISP hardware block. This driver uses the MMAL
component to program the ISP hardware through the VC firmware.
The ISP component can produce two video stream outputs, and Bayer
image statistics. This can't be encompassed in a simple V4L2
M2M device, so create a new device that registers 4 video nodes.
This patch squashes all the development patches from the earlier
rpi-5.4.y branch into one
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
This file defines the userland interface to the bcm2835-isp driver
that will follow in a separate commit.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
If CONFIG_DMA_BCM2708 isn't enabled there's no need to mask out
one of the already scarce DMA channels.
Signed-off-by: Matthias Reichl <hias@horus.com>
This adds a V4L2 memory to memory device that wraps the MMAL
video decode and video_encode components for H264 and MJPEG encode
and decode, MPEG4, H263, and VP8 decode (and MPEG2 decode
if the appropriate licence has been purchased).
This patch squashes all the work done in developing the driver
on the Raspberry Pi rpi-5.4.y kernel branch.
Thanks to Kieran Bingham, Aman Gupta, Chen-Yu Tsai, and
Marek Behún for their contributions. Please refer to the
rpi-5.4.y branch for the full history.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
With the vc-sm-cma driver we can support zero copy of buffers between
the kernel and VPU. Add this support to mmal-vchiq.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Add Broadcom VideoCore Shared Memory support.
This new driver allows contiguous memory blocks to be imported
into the VideoCore VPU memory map, and manages the lifetime of
those objects, only releasing the source dmabuf once the VPU has
confirmed it has finished with it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
If the RBUF logic is not reset when the kernel starts then there
may be some data left over from any network boot loader. If the
64-byte packet headers are enabled then this can be fatal.
Extend bcmgenet_dma_disable to do perform the reset, but not when
called from bcmgenet_resume in order to preserve a wake packet.
N.B. This different handling of resume is just based on a hunch -
why else wouldn't one reset the RBUF as well as the TBUF? If this
isn't the case then it's easy to change the patch to make the RBUF
reset unconditional.
See: https://github.com/raspberrypi/linux/issues/3850
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Increase the delay before entering the lower power state to 2 seconds
(the maximum allowed) in order to reduce the packet latencies,
particularly for inbound packets.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Display variants are intended as a replacement for the now-deleted
fbtft_device drivers. Drivers can register additional compatible
strings with a custom callback that can make the required changes
to the fbtft_display structure.
Start the ball rolling by adding adafruit18, adafruit18_green and
sainsmart18 displays.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Since the unicam driver was modified to write to a dummy buffer when no
user-supplied buffer is available, it can now write to and return a
buffer even when there's only a single one. Enable this by changing the
min_buffers_needed in the vb2_queue; it will be useful for enabling
still captures without allocating more memory than absolutely necessary.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
The change to retrieve the pixel format always on g_fmt didn't
check whether the native or unpacked version of the format
had been requested, and always returned the packed one.
Correct this so that the packing setting is retained whereever
possible.
Fixes "9d59e89 media: bcm2835-unicam: Re-fetch mbus code from subdev
on a g_fmt call"
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
From when bringing up the driver, there was a check in the isr
to ignore interrupts (claiming them handled) should the driver
not be streaming.
The VPU now will not register a camera driver if it finds a
CSI2 node enabled in device tree, therefore this flawed check is
redundant.
https://github.com/raspberrypi/linux/issues/3602
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Parse device properties and register controls for them using the V4L2
fwnode properties helpers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Use V4L2_CID_EXPOSURE_AUTO_PRIORITY to control if the driver should
automatically adjust the sensor frame length based on exposure time,
allowing variable frame rates and longer exposures.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Adds a driver for the 12MPix Sony IMX477 CSI2 sensor.
Whilst the sensor supports 2 or 4 CSI2 data lanes, this driver
currently only supports 2 lanes.
The following Bayer modes are currently available:
4056x3040 12-bit @ 10fps
2028x1520 12-bit (binned) @ 40fps
2028x1050 12-bit (cropped/binned) @ 50fps
1012x760 10-bit (scaled) @ 120 fps
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Under FKMS, the firmware (via FKMS) also requires the VideoCore cache
aliases for image planes, as defined by the dma-ranges under /soc.
Add rpi-firmware-kms to the list of acceptable nodes to look for
to copy dma config from.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
This is a squash of all firmware-kms related patches from previous
branches, up to and including
"drm/vc4: Set the possible crtcs mask correctly for planes with FKMS"
plus a couple of minor fixups for the 5.9 branch.
Please refer to earlier branches for full history.
This patch includes work by Eric Anholt, James Hughes, Phil Elwell,
Dave Stevenson, Dom Cobley, and Jonathon Bell.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm/vc4: Fixup firmware-kms after "drm/atomic: Pass the full state to CRTC atomic enable/disable"
Prototype for those calls changed, so amend fkms (which isn't
upstream) to match.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The BT601/BT709 color encoding and limited vs full
range properties were not being exposed, defaulting
always to BT601 limited range.
Expose the parameters and set the registers appropriately.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
This currently doesn't handle non-zero source rectangles correctly,
but add support for DRM_FORMAT_P030 with DRM_FORMAT_MOD_BROADCOM_SAND128
modifier to planes when running on HVS5.
WIP still for source cropping SAND/P030 formats
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Currently we call cec_phys_addr_invalidate on a hotplug deassert.
That may be due to a TV power cycling, or an AVR being switched
on (and switching edid). This makes CEC unusable.
Set it back up again on the hotplug assert.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
This follows logic in hdmi-codec.c to use speaker layout
from ELD to choose a suitable speaker mapping based on
number of channels requested and signal that in audio
infoframe and report this back to userspace.
This allows apps like speaker-test and kodi to get the
output to the right speakers.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Without this bit set, HDMI_MAI_FORMAT doesn't pick up
the format and samplerate from DVP_CFG_MAI0_FMT and you
can't get HDMI_HDMI_13_AUDIO_STATUS_1 to indicate HBR mode
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
This was a workaround for bugs in hardware on earlier Pi models
and wasn't totally successful.
It makes audio quality worse on a Pi4 at the higher sample rates
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Configuring HDMI audio registers in prepare allows us to take
IEC958 bits into account which are set by the alsa hook after
the hw_params call.
Signed-off-by: Matthias Reichl <hias@horus.com>
Although vc4 get an IEC958 formatted stream passed in from userspace
the driver needs the info from the channel status bits to properly
set up the hardware, eg for HBR passthrough.
Add iec958 controls so the channel status bits can be passed in
from userspace.
Signed-off-by: Matthias Reichl <hias@horus.com>
The hardware uses this for generating the right audio
data island packets when using formats other than PCM
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Symptom is random switching of speakers when using multichannel.
Repeatedly running speakertest -c8 occasionally starts with
channels jumbled. This is fixed with HD_CTL_WHOLSMP.
The other bit looks beneficial and apears harmless in testing so
I'd suggest adding it too.
Documentation says: HD_CTL_WHILSMP_SET
Wait for whole sample. When this bit is set MAI transmit will start
only when there is at least one whole sample available in the fifo.
Documentation says: HD_CTL_CHALIGN_SET
Channel Align When Overflow. This bit is used to realign the audio
channels in case of an overflow.
If this bit is set, after the detection of an overflow, equal
amount of dummy words to the missing words will be written to fifo,
filling up the broken sample and maintaining alignment.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
vc4_drv isn't necessarily under the /soc node in DT as it is a
virtual device, but it is the one that does the allocations.
The DMA addresses are consumed by primarily the HVS or V3D, and
those require VideoCore cache alias address mapping, and so will be
under /soc.
During probe find the a suitable device node for HVS or V3D,
and adopt the DMA configuration of that node.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
During a bulk transfer we request a DMA allocation to hold the
scatter-gather list. Most of the time, this allocation is small
(<< PAGE_SIZE), however it can be requested at a high enough frequency
to cause fragmentation and/or stress the CMA allocator (think time
spent in compaction here, or during allocations elsewhere).
Implement a pool to serve up small DMA allocations, falling back
to a coherent allocation if the request is greater than
VCHIQ_DMA_POOL_SIZE.
Signed-off-by: Oliver Gjoneski <ogjoneski@gmail.com>
The sensor supports 8 bit mode as well as 10bit, so add the
relevant code to allow selection of this.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Fix commit "media: tc358743: Return an appropriate colorspace from
tc358743_set_fmt" to ensure that the format passed in to set_fmt
is checked to be valid, and reset to the current format if not.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Pi 0&1 pass all ARM accesses through the VPU L2 cache, therefore
the dma-ranges property sets the cache alias bits to other
than the direct alias, hence this WARN was firing.
It was overprotective coding, so assume that everything is OK
with the dma-ranges, and remove the WARN.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
MEDIA_CONTROLLER_REQUEST_API is a hidden option. If rpivid depends on it,
the user would need to first enable another driver that selects
MEDIA_CONTROLLER_REQUEST_API, and only then rpivid would become available.
By selecting it instead of depending on it, it becomes possible to enable
rpivid without having to enable other potentially unnecessary drivers.
Signed-off-by: Hristo Venev <hristo@venev.name>
In an attempt to prevent the problem of CPUn not starting, explicitly
misalign the scratch space used to save registers acros the cache
invalidation.
Notes:
At this stage in the boot process the core is running with its cache
disabled. Before enabling the cache its contents must be explicitly
invalidated, a process that requires quite a few registers that the
caller must preserve. Evidence suggests that something is writing a
block of zeroes over that space at a time when all other cores should
be idle, possibly some kind of write-combiner, and the misalignment is
designed to disrupt any write-coalescing.
In truth, I don't understand why this patch works, and when the failure
is so random it is hard to be certain that this isn't just rolling the
dice again. One interesting test would be to change the "addeq r12, #4"s
to "addeq r12, #0"s determine see if the offset itself is significant or
just the additional code.
See: https://github.com/Hexxeh/rpi-firmware/issues/232
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Although it is no longer necessary for vchiq's children to have a
different DMA configuration to the parent, they do still need to
explicitly to have their DMA configuration set - to be that of the
parent.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The actpwr trigger is a meta trigger that cycles between an inverted
mmc0 and default-on. It is written in a way that could fairly easily
be generalised to support alternative sets of source triggers.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Parse device properties and register controls for them using the V4L2
fwnode properties helpers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
When streaming with Unicam, the VPU must have a clock frequency of at
least 250Mhz. Otherwise, the input fifos could overrun, causing
image corruption.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
[g|s]_selection pass in a buffer type that needs to be validated
before passing on to the sensor subdev.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
v4l2-compliance throws a failure if the device doesn't advertise
V4L2_CAP_READWRITE but allows read or write operations.
We do support read, so reinstate the flag.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The colorspace fields were left untouched in imx290_set_fmt
which lead to a v4l2-compliance failure.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Userspace needs to know the cropping arrangements for each mode,
so expose this through g_selection.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
__v4l2_ctrl_modify_range only updates the current value should
it be invalid within the new range. That can leave modes producing
odd frame rates.
Explicitly update the HBLANK and VBLANK values so that on mode
change we revert to the default frame rate for the mode.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Vision Components have made an OV9281 module which blocks reading
back the majority of registers to comply with NDAs, and in doing
so doesn't allow auto-increment register reading as used when
reading the chip ID.
Use two reads and manually combine the results.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The Rockchip driver was based on a 4.4 kernel, and had several custom
Rockchip parts.
Update to 5.4 kernel APIs, with the relevant controls required by
libcamera, and remove custom Rockchip parts.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Adds the ov9281 parts of the Rockchip patch adding enum_frame_interval to
a large number of drivers.
Change-Id: I03344cd6cf278dd7c18fce8e97479089ef185a5c
Signed-off-by: Zefa Chen <zefa.chen@rock-chips.com>
Takes the ov9281 part only from the Rockchip's patch.
Change-Id: I30e833baf2c1bb07d6d87ddb3b00759ab45a90e4
Signed-off-by: Zefa Chen <zefa.chen@rock-chips.com>
Use bit 27 of the dreq value (the second cell of the DT DMA descriptor)
to request that the WAIT_RESP bit is not set.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Now that the 14bit non-packed Bayer formats are defined, add them
into the supported formats lookup table.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Now that V4L2_PIX_FMT_Y14 and V4L2_PIX_FMT_Y14P are defined,
allow passing 14bit mono data through the peripheral.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Now that V4L2_PIX_FMT_Y12P is defined, allow passing raw 12bit
mono packed data through the peripheral.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
imx290_set_hmax was using two independent writes to set up hmax,
when all other multi-register writes were using imx290_write_buffered_reg
which claims the group hold first.
Switch imx290_set_hmax to using imx290_write_buffered_reg too.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The IMX290 module is available as either mono or colour (Bayer).
Update the driver so that it can advertise the correct mono
formats instead of the colour ones.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The IMX290 module is available as either monochrome or colour and
the variant is not detectable at runtime.
Add a new compatible string for the monochrome version.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The sensor supports horizontal and vertical flips, so support them
through V4L2_CID_HFLIP and V4L2_CID_VFLIP.
This sensor does NOT change the Bayer order when changing the
direction of readout, therefore no special handling is required for
that.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Adds support for V4L2_CID_EXPOSURE so that userspace can control
the sensor exposure time.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
In order to calculate framerate and durations userspace needs
the vertical blanking information. This can be configurable,
and indeed the datasheet lists different values for VBLANK for
the 1080p and 720p modes.
Add the new control, and adopt the datasheet values for each mode.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Userspace needs to know HBLANK if it is to work out exposure times
and frame rates, therefore convert it to map onto V4L2_CID_HBLANK
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The datasheet lists the gain as being 0.0 to 72.0dB in 0.3dB steps, which
makes 238 steps total.
Correct the 0-72 range defined in the driver.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The existing driver only supported a clock of 37.125MHz, but the
sensor also supports 74.25MHz.
Add the relevant register modifications to support this alternate
clock frequency.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Commit d46cfdc86c upstream.
With the current driver 'media-ctl -p' issued right after the imx290 driver
is loaded prints:
pad0: Source
[fmt:unknown/0x0]
The format value of zero is due to the current_format field of the imx290
struct not being initialized yet.
As imx290_entity_init_cfg() calls imx290_set_fmt(), the current_mode field
is also initialized, so the line which set current_mode to a default value
in driver's probe() function is no longer needed.
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Older gcc versions object to = { 0 } initialisation if the first
elemtn in the structure is a substructure.
Use = { } to avoid this compiler warning.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Use the get_mbus_config pad subdev call to allow a source to use
fewer than the number of CSI2 lanes defined in device tree.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Add a driver for the Unicam camera receiver block on BCM283x processors.
Compared to the bcm2835-camera driver present in staging, this driver
handles the Unicam block only (CSI-2 receiver), and doesn't depend on
the VC4 firmware running on the VPU.
The commit is made up of a series of changes cherry-picked from the
rpi-5.4.y branch of https://github.com/raspberrypi/linux/ with
additional enhancements, forward-ported to the mainline kernel.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reported-by: kbuild test robot <lkp@intel.com>
Commit 8353fe6f1e ("Revert "staging: bcm2835-audio: Drop DT
dependency"") reverts the upstream change and makes bcm2835-audio use
device tree again, however, it also removes the MODULE_ALIAS for the
platform device. This MODULE_ALIAS is needed, because VCHIQ registers
bcm2835-audio as a child platform device since commit 25c7597af2
("staging: vchiq_arm: Register a platform device for audio"), and this
mechanism is adopted also in the downstream kernel.
This commit puts back that MODULE_ALIAS to make bcm2835-audio
autoprobing work again. The rest of VCHIQ children have their
MODULE_ALIASes in place.
Fixes: 8353fe6f1e ("Revert "staging: bcm2835-audio: Drop DT dependency"")
Signed-off-by: Maxim Mikityanskiy <maxtram95@gmail.com>
When closing the video device, the irs1125 is put in power down state.
To keep V4L2 ctrls and the HW in sync, v4l2_ctrl_handler_setup is
called after power up.
The compound ctrl IRS1125_CID_MOD_PLL however has a default value
of all zeros, which puts the imager into a non responding state.
Thus, this ctrl is not written by the driver into HW after power up.
The userspace has to take care to write senseful data.
Signed-off-by: Markus Proeller <markus.proeller@pieye.org>
Instead of changing the exposure and framerate settings for all sequences,
they can be changed for every sequence individually now. Therefore the
IRS1125_CID_SAFE_RECONFIG ctrl has been removed and replaced by
IRS1125_CID_SAFE_RECONFIG_S<seq_num>_EXPO and *_FRAME ctrls.
The consistency check in the sequence ctrl IRS1125_CID_SEQ_CONFIG
is removed.
Signed-off-by: Markus Proeller <markus.proeller@pieye.org>
Reading data over i2c is done by using i2c_transfer to ensure that this
operation can't be interrupted.
Signed-off-by: Markus Proeller <markus.proeller@pieye.org>
The BRCM PCIe block has controls to enable control of the CLKREQ#
signal by the L1SS, and to gate the refclk with the CLKREQ# input.
These controls are mutually exclusive - the upstream code sets the
latter, but some use cases require the former.
Add a Device Tree property - brcm,enable-l1ss - to switch to the
L1SS configuration.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Upstream Linux deems using output GPIOs to generate IRQs as a bogus
use case, even though the BCM2835 GPIO controller is capable of doing
so. A number of users would like to make use of this facility, so
disable the checks.
See: https://github.com/raspberrypi/linux/issues/2527
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Things don't work too well when both the vc4 driver and the firmware
driver are trying to control the same audio output:
[ 763.569406] bcm2835_audio bcm2835_audio: vchi message timeout, msg=5
Hence, when the vc4 HDMI driver is used, let it control audio. This is done
by introducing a new device tree property to the audio node, and
extending the vc4-kms-v3d overlays to set it appropriately.
Signed-off-by: Hristo Venev <hristo@venev.name>
Since the unicam driver was modified to write to a dummy buffer when no
user-supplied buffer is available, it can now write to and return a
buffer even when there's only a single one. Enable this by changing the
min_buffers_needed in the vb2_queue; it will be useful for enabling
still captures without allocating more memory than absolutely necessary.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Manage the split between addresses for the VPU and addresses for the
40-bit DMA controller with a dedicated DMA device pointer that on non-
BCM2711 platforms is the same as the main VCHIQ device. This allows
the VCHIQ node to stay in the usual place in the DT, and removes the
ugly VC_SAFE macros.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
staging: vchiq_arm: Use g_dma_dev for dma_unmap_sg
Commit "staging: vchiq_arm: Clean up 40-bit DMA support" failed to
change one of the calls to dma_unmap_sg to pass in g_dma_dev (rather
than g_dev). Correct that oversight.
See: https://github.com/raspberrypi/linux/issues/3647
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Without this patch GPIOs don't seem to work properly, primarily
noticeable as broken LEDs.
Squash with "pinctrl-bcm2835: Set base to 0 give expected gpio numbering"
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Enabling zswap support in the kernel configuration costs about 1.5MB
of RAM, even when zswap is not enabled at runtime. This cost can be
reduced significantly by deferring initialisation (including pool
creation) until the "enabled" parameter is set to true. There is a
small cost to this in that some initialisation code has to remain in
memory after the init phase, just in case they are needed later,
but the total size increase is negligible.
See: https://github.com/raspberrypi/linux/pull/3432
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The change to retrieve the pixel format always on g_fmt didn't
check whether the native or unpacked version of the format
had been requested, and always returned the packed one.
Correct this so that the packing setting is retained whereever
possible.
Fixes "9d59e89 media: bcm2835-unicam: Re-fetch mbus code from subdev
on a g_fmt call"
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The GCC plugin feature leads to different kernel configurations on what
ought to be equivalent build systems because they depend on the build
hosts native compilers rather than the cross compilers needed for the
target. This causes problems with module symbol version mismatches.
Disable GCC plugins for all build hosts.
Advanced build script hackery borrowed from a patch by milhouse.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
V4L2 wishes to have the codec header bytes in the same buffer as the
first encoded frame, so it does become 1-in 1-out for encoding.
The firmware now has an option to do this, so enable it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The SC16IS7XX hardware flow control is mishandled by the driver in
a number of ways:
1. The set_baud method accidentally clears it when setting EFR bit.
2. Even though hardware flow control is enabled, it isn't indicated
back to the serial framework.
3. Applying the flow control clears the EFR bit.
4. The CTS support is not indicated in the return from
sc16is7xx_get_mctrl.
Address all of those issues using a mixture of patches found on the
linked pages.
See: https://github.com/raspberrypi/linux/issues/2542
See: https://www.spinics.net/lists/linux-serial/msg21794.html
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
From when bringing up the driver, there was a check in the isr
to ignore interrupts (claiming them handled) should the driver
not be streaming.
The VPU now will not register a camera driver if it finds a
CSI2 node enabled in device tree, therefore this flawed check is
redundant.
https://github.com/raspberrypi/linux/issues/3602
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
If the firmware hasn't detected a display, the driver would assume
one display was available, but because it had failed to retrieve the
display size it would try to allocate a zero-sized buffer.
Avoid the allocation failure by bailing out early if no display is
found.
See: https://github.com/raspberrypi/linux/issues/3598
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The reference counting of node->open was only incremented after
a check that the node was v4l2_fh_is_singular_file, which resulted
in the counting going wrong and s_power not being called at an
appropriate time.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
unicam_release calls _vb2_fop_release, which will call stop_streaming
if that particular node was streaming. Calling it unconditionally (as
the code was) means that if a second handle was opened eg to alter
a setting, on closing that connection it also stopped Unicam.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Sensors are now reflecting cropping and scaling parameters through
the selection API, therefore Unicam needs to forward the requests
through to the subdev.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Exposure is clipped by the VTS of the mode, so needs to be updated as
and when this is changed.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
To make adding new members to the mode structures easier, use
the member names in the initialisers.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The controls for analogue gain and exposure were defined with
V4L2_CTRL_FLAG_EXECUTE_ON_WRITE. This is not required as we only need
to send changes to the sensor.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The ov5647 subdev can generate control events, therefore set
the V4L2_SUBDEV_FL_HAS_EVENTS flag.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Clients need to know the pixel rate in order to compute exposure
and frame rate values.
Advertise it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
"87f3ab9 media: ov5647: Add basic support for multiple sensor modes."
added a return path ov5647_set_fmt that didn't release the device
mutex that it had claimed.
Release the mutex.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
In order to apply lens shading correctly the client needs to know how
each mode crops or scales the image compared to the full sensor array.
Implement this (based on the imx219 equivalent).
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Specifically:
* AWB is now off by default.
* AEC/AGC is also off by default.
* The default mode is changed to the 10-bit 2x2 binned mode.
AWB and AEC/AGC can be re-enabled using the usual V4L2 controls. The
original 8-bit mode will be respected if an application requests the
8-bit format.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
The 8-bit VGA mode remains, we add the following 10-bit modes:
Mode 0: 2592x1944 full resolution.
Mode 1: 1920x1080 full resolution, but centre-cropped.
(This mode achieves 30fps, mode 0 does not.)
Mode 2: 1296x972 full field-of-view 2x2 binned mode.
Mode 3: VGA full field of view mode.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Added basic v4l2_ctrl_handler infrastructure (there was none
previously).
Added controls to let AWB/AEC/AGC run in the sensor's auto mode or
manually. Also controls to set exposure (in lines) and analogue gain
(as a register code) from user code.
Also delete registers (just the one) from the VGA mode register set
that are now controlled by the new V4L2 controls.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Specifically:
Added a structure ov5647_mode and a list of supported_modes (though no
actual new modes as yet). The state object points to the "current mode".
ov5647_enum_mbus_code, ov5647_enum_frame_size, ov5647_set_fmt and
ov5647_get_fmt all needed upgrading to cope with multiple modes.
__sensor_init (which writes all the registers) is now called by
ov5647_stream_on (once the mode is known) rather than by
ov5647_sensor_power.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Previously they were returning positive non-zero codes for success,
which were getting passed up the call stack. Since release 4.19,
do_dentry_open (fs/open.c) has been catching these and flagging an
error. (So this driver has been broken since that date.)
Fixes: 3c2472a [media] media: i2c: Add support for OV5647 sensor
Signed-off-by: David Plowman <david.plowman@raspberrypi.org>
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
The flag V4L2_SUBDEV_FL_HAS_EVENTS is required if the subdev can
generate events. It can create events from the ctrl handler, therefore
this is required.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Like many overlays, the i2c-gpio overlay goes to efforts to avoid
generating warnings about #address-cells and #size-cells not
being defined, which it does by defining them. Unfortunately this
is fatal if they don't match what the system requires, and the
recent switch to #size-cells = 2 on 2711 made i2c-gpio very
dangerous.
In the absence of the knowledge of a clean way to fix this, just delete
the declarations and suffer the warnings.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
BCM2711 has 4 DMA channels with a 40-bit address range, allowing them
to access the full 4GB of memory on a Pi 4.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcmn2835_isp is a platform driver dependent on vchiq,
therefore add the load/unload functions for it to vchiq.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Add V4L2_META_FMT_BCM2835_ISP_STATS V4L2 format type.
This new format will be used by the BCM2835 ISP device to return
out ISP statistics for 3A.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
The sensor subdevice may change the Bayer order if a H/V flip is
requested after a s_fmt call. Unicam g_fmt must call the subdev get_fmt
in case this has happened and return out the correct format 4cc.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
This commit updates the imx219 driver to adverise support for embedded
data streams. This can then be used by the bcm2835-unicam driver, which
has recently been updated to expose the embedded data stream to
userland.
The imx219 sensor subdevice overloads the media pad to differentiate
between image stream (pad 0) and embedded data stream (pad 1) when
performing the v4l2_subdev_pad_ops functions.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
The unicam driver supports both the SOURCE_CHANGE and CTRL events. Both
events are only generated on the image video node, so the event-related
ioctls are useless on the medatada node. Disable them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
If no buffer has been queued by a userland application, we use an
internal dummy buffer for the hardware to spin in. This will allow
the driver to release the existing userland buffer back to the
application for processing.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
This patch adds a new node in the bcm2835-unicam driver to support
CSI-2 embedded data streams. The subdevice is queried to see if
embedded data is available from the sensor.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Move device node specific state out of the device state structure and
into a new node structure. This separation will be needed for future
changes where we will add an embedded data node to the driver to work
alongside the existing image data node.
Currently only use a single image node, so this commit does not add
any functional changes.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
This patch adds MEDIA_BUS_FMT_SENSOR_DATA used by the bcm2835-unicam
driver to support CSI-2 embedded data streams from camera sensors.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Add V4L2_META_FMT_SENSOR_DATA format 4CC.
This new format will be used by the BCM2835 Unicam device to return
out camera sensor embedded data.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Add driver for the Unicam camera receiver block on
BCM283x processors.
This commit is made up of a series of changes cherry-picked from the
rpi-4.19.y branch.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Limit mappings to the permitted range, but don't map more than asked
for otherwise we walk off the end of the allocated VMA.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Commit f3186dd876 ("spi: Optionally use GPIO descriptors for CS GPIOs")
amended of_spi_parse_dt() to always set SPI_CS_HIGH for SPI slaves whose
Chip Select is defined by a "cs-gpios" devicetree property.
This change breaks drivers whose probe functions set the mode field of
the spi_device because in doing so they clear the SPI_CS_HIGH flag.
Fix by setting SPI_CS_HIGH in spi_setup (under the same conditions as
in of_spi_parse_dt()).
See also: 83b2a8fe43 ("spi: spidev: Fix CS polarity if GPIO descriptors are used")
Fixes: f3186dd876 ("spi: Optionally use GPIO descriptors for CS GPIOs")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
SQUASH: spi: Demote SPI_CS_HIGH warning to KERN_DEBUG
This warning is unavoidable from a client's perspective and
doesn't indicate anything wrong (just surprising).
SQUASH with "spi: use_gpio_descriptor fixup moved to spi_setup"
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
framebuffer_check was computing a minimum pitch value and ensuring
that the provided value was greater than this.
That check is only valid if the format is linear.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The HDMI controllers found in the BCM2711 SoC need some adjustments to the
bindings, especially since the registers have been shuffled around in more
register ranges.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
When the MMC isn't plugged in, the driver will spam the console which is
pretty annoying when using NFS.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
This driver is for the HEVC/H265 decoder block on the Raspberry
Pi 4, and conforms to the V4L2 stateless decoder API.
Signed-off-by: John Cox <jc@kynesim.co.uk>
Allow the capture buffer to be detached from a v4l2 request job such
that another job can start before the capture buffer is returned. This
allows h/w codecs that can process multiple requests at the same time
to operate more efficiently.
Signed-off-by: John Cox <jc@kynesim.co.uk>
Some of the Broadcom codec blocks use a column based YUV4:2:0 image
format, so add the documentation and defines for both 8 and 10 bit
versions.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
WPP can allow greater parallelism within the decode, but needs
offset information to be passed in.
Adds num_entry_point_offsets and entry_point_offset_minus1 to
v4l2_ctrl_hevc_slice_params.
This is based on Jernej Skrabec's patches for cedrus which
implement the same feature.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
From https://patchwork.linuxtv.org/patch/60725/
Changes requested, but mainly docs.
If HEVC frame consists of multiple slices, segment address has to be
known in order to properly decode it.
Add segment address field to slice parameters.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Adds a format that is 3 10bit YUV 4:2:0 samples packed into
a 32bit work (with 2 spare bits).
Supported on Broadcom BCM2711 chips.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
This is adjustment to commit
d368ceaacd "kbuild: Allow .dtbo overlays to be built piecemeal"
prepare3 target has gone from mainline tree in branch 5.4.y
Signed-off-by: Nataliya Korovkina <malus.brandywine@gmail.com>
The DT bindings description of the Brcmstb PCIe device is described. This
node can be used by almost all Broadcom settop box chips, using
ARM, ARM64, or MIPS CPU architectures.
Signed-off-by: Jim Quinlan <jim2101024@gmail.com>
When symbols from overlays are added to the live tree their paths must
be rebased. The translated symbol is normally the result of joining
the fragment-relative path (with a leading "/") to the target path
(either copied directly from the "target-path" property or resolved
from the phandle). This translation fails when the target is the root
node (a common case for Raspberry Pi overlays) because the resulting
path starts with a double slash. For example, if target-path is "/" and
the fragment adds a node called "newnode", the label associated with
that node will be assigned the path "//newnode", which can't be found
in the tree.
Fix the failure case by explicitly replacing a target path of "/" with
an empty string.
Fixes: d1651b03c2 ("of: overlay: add overlay symbols to live device tree")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The definition of compat_ptr is now common for most platforms, but
requires the inclusion of <linux/compat.h>.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The definition of compat_ptr is now common for most platforms, but
requires the inclusion of <linux/compat.h>.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The downstream .dts files only request two GPIO IRQs. Truncate the
array of parent IRQs when irq_of_parse_and_map returns 0.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
pinctrl-bcm2835 is a combined pinctrl/gpio driver. Currently the gpio
side is registered first, but this breaks gpio hogs (which are
configured during gpiochip_add_data). Part of the hog initialisation
is a call to pinctrl_gpio_request, and since the pinctrl driver hasn't
yet been registered this results in an -EPROBE_DEFER from which it can
never recover.
Change the initialisation sequence to register the pinctrl driver
first.
See: https://www.raspberrypi.org/forums/viewtopic.php?f=107&t=260600
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
A failure in gpiochip_irqchip_add leads to a leak of a gpiochip. Fix
the leak with the use of devm_gpiochip_add_data.
Fixes: 85ae9e512f ("pinctrl: bcm2835: switch to GPIOLIB_IRQCHIP")
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
vchiq kernel clients are now instantiated as platform drivers rather
than using DT, but the children of the vchiq interface may still
benefit from access to DT properties. Give them the option of a
a sub-node of the vchiq parent for configuration and to allow
them to be disabled.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The IMA (Integrity Measurement Architecture) looks for a TPM (Trusted
Platform Module) having been registered when it initialises; otherwise
it assumes there is no TPM. It has been observed on BCM2835 that IMA
is initialised before TPM, and that initialising the BCM2835 clock
driver before the firmware driver has the effect of reversing this
order.
Change the firmware driver to initialise at core_initcall, delaying the
BCM2835 clock driver to postcore_initcall.
See: https://github.com/raspberrypi/linux/issues/3291https://github.com/raspberrypi/linux/pull/3297
Signed-off-by: Luke Hinds <lhinds@redhat.com>
Co-authored-by: Phil Elwell <phil@raspberrypi.org>
vchiq on Pi4 is no longer under the soc node, therefore it
doesn't get the dma-ranges for the VPU.
Switch to using the configuration of the old dma controller as
that will set the dma-ranges correctly.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
The VCHIQ driver now loads the audio, camera, codec, and vc-sm
drivers as platform drivers. However they were not being given
the correct DMA configuration.
Call of_dma_configure with the parent (VCHIQ) parameters to be
inherited by the child.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Both coherent_dma_mask and dma_mask act as constraints on allocations
and bounce buffer usage, so be sure to set dma_mask to the appropriate
value otherwise the effective mask could be incorrect.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
For performance/power it is beneficial to adjust gpu clocks with arm clock.
This is how the downstream cpufreq driver works
Signed-off-by: popcornmix <popcornmix@gmail.com>
Setting the v3d clock to low value allows firmware to handle dvfs in case
where v3d hardware is not being actively used (e.g. console use).
Signed-off-by: popcornmix <popcornmix@gmail.com>
Add device tree entries and code to allow the specification of
the lighting modes for the LED's on the ethernet connector.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
Following the same pattern as bcm2835-camera and bcm2835-audio,
register the V4L2 codec driver as a platform driver
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Following the same pattern as bcm2835-camera and bcm2835-audio,
register the vcsm-cma driver as a platform driver
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The irq_fence and done_fence are given a reference that is never
released. The necessary dma_fence_put()s seem to have been
deleted in error in an earlier commit.
Fixes: 0b73676836b2 ("drm/v3d: Clock V3D down when not in use.")
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The v3d driver currently encounters a lot of MMU PTE exceptions, so
only log the first to avoid swamping the kernel log.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
MMU exception conditions are reported in the V3D_MMU_CTRL register as
write-1-to-clear (W1C) bits. The MMU interrupt handling code clears any
exceptions, but does so by masking out any other bits and writing the
result back. There are some important control bits in that register,
including MMU_ENABLE, so a safer approach is to simply write back the
value just read unaltered.
This patch doesn't remove the cause of the apparent PTE errors, but it
does reduce the impact to just an error in the kernel log.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The Infineon IRS1125 is a time of flight depth sensor that
has a CSI-2 interface.
Add a V4L2 subdevice driver for this device.
Signed-off-by: Markus Proeller <markus.proeller@pieye.org>
HDMI Alsa devices renamed to match names used by DRM, to
HDMI 1 and HDMI 2
Check for which HDMI devices are connected and only create
devices for those that are present.
The rename of the devices might cause some backwards compatibility
issues, but since this particular part of the driver needs to be
specifically enabled, I suspect the number of people who will see
the problem will be very small.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
After the decision to use bcm2711 compatible for upstream, we should
switch all accepted compatibles to bcm2711. So we can boot with
one DTB the down- and the upstream kernel.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Before 4.20, it was possible to build an arbitrary overlay by copying
it to arm/boot/dts/overlays/mytest-overlay.dts and running:
make ARCH=arm overlays/mytest.dtbo
In 4.20 the .dtb build rules were centralised, requiring the dowstream
.dtbo build rules to be changed. They were, enough to support "make ...
dtbs", but not sufficiently to allow this ad-hoc, one-off building of
individual files.
Add the missing makefile rule to support this way of building.
See: https://github.com/raspberrypi/linux/issues/3250
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
This is mainly used for the NoIR camera which has no IR
filter and can completely confuse normal AWB presets.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Adds a simple greyworld white balance preset, mainly for use
with cameras without an IR filter (eg Raspberry Pi NoIR)
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
The IMX219 is an 8MPix CSI2 sensor, supporting 2 or 4 data lanes.
Document the binding for this device.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Users have reported log spam created by "Event Ring Full" xHC event
TRBs. These are caused by interrupt latency in conjunction with a very
busy set of devices on the bus. The errors are benign, but throughput
will suffer as the xHC will pause processing of transfers until the
event ring is drained by the kernel. Expand the number of event TRB slots
available by increasing the number of event ring segments in the ERST.
Controllers have a hardware-defined limit as to the number of ERST
entries they can process, so make the actual number in use
min(ERST_MAX_SEGS, hw_max).
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Some combinations of Pi 4Bs and Ethernet switches don't reliably get a
DCHP-assigned IP address, leaving the unit with a self=assigned 169.254
address. In the failure case, the Pi is left able to receive packets
but not send them, suggesting that the MAC<->PHY link is getting into
a bad state.
It has been found empirically that skipping a reset step by the genet
driver prevents the failures. No downsides have been discovered yet,
and unlike the forced renegotiation it doesn't increase the time to
get an IP address, so the workaround is enabled by default; add
genet.skip_umac_reset=n
to the command line to disable it.
See: https://github.com/raspberrypi/linux/issues/3108
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
These wireless mouse/keyboard combo remote control devices specify
multiple "wheel" events in their report descriptors. The wheel events
are incorrectly defined and apparently map to accelerometer data, leading
to spurious mouse scroll events being generated at an extreme rate when
the device is moved.
As a workaround, use HID_QUIRK_INCREMENT_USAGE_ON_DUPLICATE to mask
feeding the extra wheel events to the input subsystem.
See: https://github.com/raspberrypi/firmware/issues/1189
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Based on the gpiomem driver, allow mapping of the decoder register
spaces such that userspace can access control/status registers.
This driver is intended for use with a custom ffmpeg backend accelerator
prior to a v4l2 driver being written.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
driver: char: rpivid: Destroy the legacy device on remove
The legacy name support created a new device that was never destroyed.
If the driver was unloaded and reloaded, it failed due to the
device already existing.
Fixes: "75f1d14 driver: char: rpivid - also support legacy name"
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
driver: char: rpivid: Clean up error handling use of ERR_PTR/IS_ERR
The driver used an unnecessary intermediate void* variable so it
only called ERR_PTR once to convert to the error value.
Switch to converting as the error arises to remove these intermediate
variables.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
driver: char: rpivid: Add error handling to the legacy device load
The return value from device_create for the legacy device was never
checked or handled. Add the required error handling.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
driver: char: rpivid: Fix coding style whitespace issues.
Makes checkpatch happier.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
driver: char: rpimem: Add SPDX licence header.
Stops checkpatch complaining.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
driver: char: rpivid: Fix access to freed memory
The error path during probe frees the private memory block, and
then promptly dereferences it to log an error message.
Use the base device instead of the pointer to it in the private
structure.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
My various attempts at re-enabling runtime PM have failed, so just
crank the clock down when V3D is idle to reduce power consumption.
Signed-off-by: Eric Anholt <eric@anholt.net>
Something is still unstable -- on starting a new glxgears from an idle
X11, I get an MMU violation in high addresses. The CTS also failed
quite quickly. With this, CTS progresses for an hour before OOMing
(allocating some big buffers when my board only has 600MB available to
Linux)
Signed-off-by: Eric Anholt <eric@anholt.net>
The BCM2835 I2C blocks have a register to set the clock-stretch
timeout - how long the device is allowed to hold SCL low - in bus
cycles. The current driver doesn't write to the register, therefore
the default value of 64 cycles is being used for all devices.
Set the timeout to the value recommended for SMBus - 35ms.
See: https://github.com/raspberrypi/linux/issues/3064
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Seen on a VLI VL805 PCIe to USB controller. For non-stream endpoints
at least, if the xHC halts on a particular TRB due to an error then
the DCS field in the Out Endpoint Context maintained by the hardware
is not updated with the current cycle state.
Using the quirk XHCI_EP_CTX_BROKEN_DCS and instead fetch the DCS bit
from the TRB that the xHC stopped on.
See: https://github.com/raspberrypi/linux/issues/3060
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
In translating the runtime PM code from vc4, I missed the ".pm"
assignment to actually connect them up. Fixes missing MMU setup if
runtime PM resets V3D.
Signed-off-by: Eric Anholt <eric@anholt.net>
(cherry picked from commit ca197699af29baa8236c74c53d4904ca8957ee06)
If it's off, we know it will be reset on poweron, so the MMU won't
have any TLB cached from before this point. Avoids failed waits for
MMU flush to reply.
Signed-off-by: Eric Anholt <eric@anholt.net>
(cherry picked from commit 3ee4e2e0a9e9587eacbb69b067bbc72ab2cdc47b)
Must be called in a non-atomic context, after the endpoint
has been registered with the hardware via xhci_add_endpoint
and before the first URB is submitted for the endpoint.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
xHCI caches device and endpoint data after the interface is configured,
so an explicit command needs to be issued for any device driver wanting
to alter the polling interval of an endpoint.
Add usb_fixup_endpoint() to allow drivers to do this. The fixup must be
called after calculating endpoint bandwidth requirements but before any
URBs are submitted.
If polling intervals are shortened, any bandwidth reservations are no
longer valid but in practice polling intervals are only ever relaxed.
Limit the scope to interrupt transfers for now.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
This falls under the same "we can reprogram glitch-free as long as we
pause generation" rule as updating the div/frac fields. This can be
used for runtime reclocking of V3D to manage power leakage.
Signed-off-by: Eric Anholt <eric@anholt.net>
Without the actual power management part any more, there's a lot less
to set up for V3D. We just need to clear the RSTN field for the power
domain, and expose the reset controller for toggling it again.
This is definitely incomplete -- the old ISP and H264 is in the old
bridge, but since we have no consumers of it I've just done the
minimum to get V3D working.
Signed-off-by: Eric Anholt <eric@anholt.net>
If the VL805 EEPROM has not been programmed then boot will hang for five
seconds. The timeout seems to be arbitrary and is an unecessary
delay on the first boot. Remove the timeout.
This is common code and probably can't be upstreamed unless the timeout
can be configurable somehow or perhaps the XHCI driver can be skipped
on the first boot.
There are several warts surrounding bcmgenet_mii_probe() as this
function is called from ndo_open, but it's calling registration-type
functions. The probe should be called at probe time and refactored
such that the PHY device data can be extracted to limit the scope
of this flag to Broadcom PHYs.
For now, pass this flag in as it puts our attached PHY into a low-power
state when disconnected.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Set defaults for TX and RX packet coalescing to be equivalent to:
# ethtool -C eth0 tx-frames 10
# ethtool -C eth0 rx-usecs 50
This may be something we want to set via DT parameters in the
future.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Conditional on a new compatible string, change the pagelist encoding
such that the top 24 bits are the pfn, leaving 8 bits for run length
(-1).
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
staging/vchiq_arm: Fix bcm2711 compatible string
Fixes: "vchiq: Add 36-bit address support"
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The Linux support for controlling card power via regulators appears to
be contentious. I would argue that the default behaviour is contrary to
the SDHCI spec - turning off the power writes a reserved value to the
SD Bus Voltage Select field of the Power Control Register, which
seems to kill the Arasan/iProc controller - but fortunately there is a
hook in sdhci_ops to override the behaviour. Borrow the implementation
from sdhci_arasan_set_power.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The HWRNG on the BCM2838 is compatible to iproc-rng200, so add the
support to this driver instead of bcm2835-rng.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
hwrng: iproc-rng200: Correct SoC name
The Pi 4 SoC is called BCM2711, not BCM2838.
Fixes: "hwrng: iproc-rng200: Add BCM2838 support"
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The legacy peripherals can only address the first gigabyte of RAM, so
ensure that DMA allocations are restricted to that region.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The ioremapping creates mappings within the vmalloc area. The
equivalent early function, create_mapping, now checks that the
requested explicit virtual address is between VMALLOC_START and
VMALLOC_END. As there is no reason to have any correlation between
the physical and virtual addresses, put the required mappings at
VMALLOC_START and above.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
On error, vchiq_mmal_component_init could leave the
event context allocated for ports.
Clean them up in the error path.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
vchiq_mmal_component_init calls init_event_context for the
control port, but vchiq_mmal_component_finalise didn't free
it, causing a memory leak..
Add the free call.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
mmal_parameters.h hasn't been updated to reflect additions made
over the last few years. Update it to reflect the currently
supported parameters.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
The list of formats was copied before Bayer support was added.
The ISP supports Bayer and is being supported by the bcm2835_codec
driver, so add in the encodings for them.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
All calls to the gpio library are in contexts that can sleep,
therefore there is no issue with having those GPIOs controlled
by controllers which require sleeping (eg I2C GPIO expanders).
Switch to using gpiod_set_value_cansleep instead of gpiod_set_value
to avoid triggering the warning in gpiolib should the GPIO
controller need to sleep.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
The debug text for how many clocks have been registered
uses "%d" with a size_t. Correct it to "%zd".
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
The MMAL client_component field is used with the event
mechanism to allow the client to identify the component for
which the event is generated.
The field is only 32bits in size, therefore we can't use a
pointer to the component in a 64 bit kernel.
Component handles are already held in an array per VCHI
instance, so use the array index as the client_component handle
to avoid having to create a new IDR for this purpose.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
videobuf2 only allowed exporting a dmabuf as a file descriptor,
but there are instances where having the struct dma_buf is
useful within the kernel.
Split the current implementation into two, one step which
exports a struct dma_buf, and the second which converts that
into an fd.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Add the ability to send data to ports. This only supports
zero copy mode as the required bulk transfer setup calls
are not done.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
(Preparation for the codec driver).
The codec uses the event mechanism to report things such as
resolution changes. It is signalled by the cmd field of the buffer
being non-zero.
Add support for passing this information out to the client.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Fixes up a checkpatch error "Avoid using bool structure members
because of possible alignment issues".
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
When calling tc358743_set_fmt, the code was calling tc358743_get_fmt
to choose a valid format. However that sets the colorspace
based on what was read back from the chip. When you set the format,
then the driver would choose and program the colorspace based
on the format code.
The result was that if you called try or set format for UYVY
when the current format was RGB3 then you would get told sRGB,
and try RGB3 when current was UYVY and you would get told
SMPTE170M.
The value programmed into the chip is determined by this driver,
therefore there is no need to read back the value. Return the
colorspace based on the format set/tried instead.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Document the DT bindings for the CSI2/CCP2 receiver peripheral
(known as Unicam) on BCM283x SoCs.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Acked-by: Rob Herring <robh@kernel.org>
New helper defines that allow printing of a FOURCC using
printf(V4L2_FOURCC_CONV, V4L2_FOURCC_CONV_ARGS(fourcc));
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
The ADV7282M can support YPbPr on AIN1-3, but this was
not selectable from the driver. Add it to the list of
supported input modes.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
The hardware default is differential CVBS on AIN1 & 2, which
isn't very useful.
Select the first input that is defined as valid for the
chip variant (typically CVBS_AIN1).
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
The probe for the TC358743 reads the CHIPID register from
the device and compares it to the expected value of 0.
If the I2C request fails then that also returns 0, so
the driver loads thinking that the device is there.
Generally I2C communications are reliable so there is
limited need to check the return value on every transfer,
therefore only amend the one read during probe to check
for I2C errors.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Adds register setups for running the CSI lanes at 972Mbit/s,
which allows 1080P50 UYVY down 2 lanes.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
g_mbus_config was supposed to indicate all supported lane numbers, not
only the number of those currently in active use. Since the TC358743
can dynamically reduce the number of active lanes if the required
bandwidth allows for it, report all lane numbers up to the connected
number of lanes as supported in pdata mode.
In device tree mode, do not report lane count and clock mode at all, as
the receiver driver can determine these from the device tree.
To allow communicating the number of currently active lanes, add a new
bitfield to the v4l2_mbus_config flags. This is a temporary fix, to be
used only until a better solution is found.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The existing fixed value of 16 worked for UYVY 720P60 over
2 lanes at 594MHz, or UYVY 1080P60 over 4 lanes. (RGB888
1080P60 needs 6 lanes at 594MHz).
It doesn't allow for lower resolutions to work as the FIFO
underflows.
374 is required for 1080P24-30 UYVY over 2 lanes @ 972Mbit/s, but
>374 means that the FIFO underflows on 1080P50 UYVY over 2 lanes
@ 972Mbit/s.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
The driver was only supporting continuous clock mode
although this was not stated anywhere.
Non-continuous clock saves a small amount of power and
on some SoCs is easier to interface with.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
There's no way to query the subdevice for the supported
resolutions.
Add set_fmt and get_fmt implementations.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
The lan78xx uses a 12-byte hardware rx header, so there is no need
to allocate SKBs with NET_IP_ALIGN set. Removes alignment faults
in both dwc_otg and in ipv6 processing.
Add the ability to interpret the high bits of the dreq specifier as
flags to be included in the DMA_CS register. The motivation for this
change is the ability to set the DISDEBUG flag for SD card transfers
to avoid corruption when using the VPU debugger.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The bInterval is set to 4 (i.e. 8 microframes => 1ms) and the only bit
that the driver pays attention to is "link was reset". If there's a
flapping status bit in that endpoint data, (such as if PHY negotiation
needs a few tries to get a stable link) then polling at a slower rate
would act as a de-bounce.
See: https://github.com/raspberrypi/linux/issues/2447
The driver already reported the firmware build date during probe.
The mailbox calls have been extended to also report the variant
1 = standard start.elf
2 = start_x.elf (includes camera stack)
3 = start_db.elf (includes assert logging)
4 = start_cd.elf (cutdown version for smallest memory footprint).
Log the variant during probe.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
firmware: raspberrypi: Report the fw git hash during probe
The firmware can now report the git hash from which it was built
via the mailbox, so report it during probe.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Ethernet cables with faulty or missing pairs (specifically pairs C and
D) allow auto-negotiation to 1000Mbs, but do not support the successful
establishment of a link. Add a DT property, "microchip,downshift-after",
to configure the number of auto-negotiation failures after which it
falls back to 100Mbs. Valid values are 2, 3, 4, 5 and 0, where 0 means
never downshift.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Step wise governor increases the mitigation level when the temperature
goes above a threshold and will decrease the mitigation when the
temperature falls below the threshold. If it were a case, where the
temperature hovers around a threshold, the mitigation will be applied
and removed at every iteration. This reaction to the temperature is
inefficient for performance.
The use of hysteresis temperature could avoid this ping-pong of
mitigation by relaxing the mitigation to happen only when the
temperature goes below this lower hysteresis value.
Signed-off-by: Ram Chandrasekar <rkumbako@codeaurora.org>
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Avoid a hard userspace ABI change by adding a compatible get_throttled
sysfs entry. Its value is now feed by the GET_THROTTLED requests of the
new hwmon driver. The first access to get_throttled will generate
a warning.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Although the correct fix for low voltage warnings is to
improve the power supply, the current implementation
of the detection can fill the log if the warning
happens freqently. This replaces the logging with
slightly custom ratelimited logging.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Enable EEE mode as soon as possible after connecting to the PHY, and
before phy_start. This avoids a second link negotiation, which speeds
up booting and stops the interface failing to become ready.
See: https://github.com/raspberrypi/linux/issues/2437
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
As of 4.18, a firmware that implements the update_connect_params
method but doesn't claim to support roaming causes an error. We
disabled firmware roaming in 4.4 [1] because it appeared to
prevent disconnects, but let's try with the current firmware to see
if things have improved.
[1] dd91880117
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The published API to the dynamic overlay application mechanism now
takes a Flattened Device Tree blob as input so that it can manage the
lifetime of the unflattened tree. Conveniently, the new API call -
of_overlay_fdt_apply - is virtually a drop-in replacement for
create_overlay, which can now be deleted.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
ad83c7cb2f ("irqchip/irq-bcm2836: Add support for DT interrupt polarity")
changed the way that the BCM2836/7 local interrupts are mapped; instead
of being pre-mapped they are now mapped on-demand. A side effect of this
change is that the call to irq_of_parse_and_map from armctrl_of_init
creates a new mapping, forming a gap between the IRQs and the FIQs. This
gap breaks the FIQ<->IRQ mapping which up to now has been done by assuming:
1) that the value of FIQ_START is the same as the number of normal IRQs
that will be mapped (still true), and
2) that this value is also the offset between an IRQ and its equivalent
FIQ (which is no longer the case).
Remove both assumptions by measuring the interval between the last IRQ
and the last FIQ, passing it as the parameter to init_FIQ().
Fixes: https://github.com/raspberrypi/linux/issues/2432
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Register for reboot notifications, sending RPI_FIRMWARE_NOTIFY_REBOOT
over the mailbox interface on reception.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Add two new DT properties:
* microchip,eee-enabled - a boolean to enable EEE
* microchip,tx-lpi-timer - time in microseconds to wait before entering
low power state
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
I2C busses can be assigned specific bus numbers using aliases in
Device Tree - string properties where the name is the alias and the
value is the path to the node. The current DT parameter mechanism
does not allow property names to be derived from a parameter value
in any way, so it isn't possible to generate unique or matching
aliases for nodes from an overlay that can generate multiple
instances, e.g. i2c-gpio.
Work around this limitation (at least temporarily) by allowing
the i2c adapter number to be initialised from the "reg" property
if present.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
There is a new test in __irq_startup that the IRQ is activated, which
hasn't been the case for FIQs since they bypass some of the usual setup.
Augment enable_fiq to include a call to irq_activate to avoid the
warning.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Create a semi-static mapping for the USB registers early in the boot
process, before additional kernel threads are started, so all threads
will have the mappings from the start. This avoids the need for
data aborts to lazily update them.
See: https://github.com/raspberrypi/linux/issues/2450
Signed-off-by: Floris Bos <bos@je-eigen-domein.nl>
The VideoCore bootloader passes in Serial number and
Revision number through Device Tree. Make these available to
userspace through /proc/cpuinfo.
Mainline status:
There is a commit in linux-next that standardize passing the serial
number through Device Tree (string: /serial-number):
ARM: 8355/1: arch: Show the serial number from devicetree in cpuinfo
There was an attempt to do the same with the revision number, but it
didn't get in:
[PATCH v2 1/2] arm: devtree: Set system_rev from DT revision
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Uses the debugfs I/F to provide access to the AXI
bus performance monitors.
Requires the new mailbox peripheral access for access
to the VPU performance registers, system bus access
is done using direct register reads.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
raspberrypi_axi_monitor: suppress warning
Suppress the following warning by casting the pointer to and uintptr_t
before to u32:
Signed-off-by: Matteo Croce <mcroce@redhat.com>
IRQ-CPU mapping is round robined on ARM64 to increase
concurrency and allow multiple interrupts to be serviced
at a time. This reduces the need for FIQ.
Signed-off-by: Michael Zoran <mzoran@crowfest.net>
brcmfmac: Disable power management
Disable wireless power saving in the brcmfmac WLAN driver. This is a
temporary measure until the connectivity loss resulting from power
saving is resolved.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
brcmfmac: Use original country code as a fallback
Commit 73345fd212:
brcmfmac: Configure country code using device specific settings
prevents region codes from working on devices that lack a region code
translation table. In the event of an absent table, preserve the old
behaviour of using the provided code as-is.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
brcmfmac: Plug memory leak in brcmf_fill_bss_param
See: https://github.com/raspberrypi/linux/issues/1471
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
brcmfmac: do not use internal roaming engine by default
Some evidence of curing disconnects with this disabled, so make it a default.
Can be overridden with module parameter roamoff=0
See: http://projectable.me/optimize-my-pi-wi-fi/
brcmfmac: Change stop_ap sequence
Patch from Broadcom/Cypress to resolve a customer error
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Revert "brcmfmac: Disable power management"
Shortly after the release of the Pi 3B, a loss of SSH connectivity
over WiFi was traced to the power management handling, so power
management was disabled. And so it has remained ever since.
Enabling power management saves 55mA (~270mW) on a Pi 4B, so is very
much worth the minimal effort of reverting this patch, which was
squashed and rebased many times since then to the commit hash is
meaningless.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
This is a port of Pantelis Antoniou's v3 port that makes use of the
new upstreamed configfs support for binary attributes.
Original commit message:
Add a runtime interface to using configfs for generic device tree overlay
usage. With it its possible to use device tree overlays without having
to use a per-platform overlay manager.
Please see Documentation/devicetree/configfs-overlays.txt for more info.
Changes since v2:
- Removed ifdef CONFIG_OF_OVERLAY (since for now it's required)
- Created a documentation entry
- Slight rewording in Kconfig
Changes since v1:
- of_resolve() -> of_resolve_phandles().
Originally-signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
DT configfs: Fix build errors on other platforms
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
DT configfs: fix build error
There is an error when compiling rpi-4.6.y branch:
CC drivers/of/configfs.o
drivers/of/configfs.c:291:21: error: initialization from incompatible pointer type [-Werror=incompatible-pointer-types]
.default_groups = of_cfs_def_groups,
^
drivers/of/configfs.c:291:21: note: (near initialization for 'of_cfs_subsys.su_group.default_groups.next')
The .default_groups is linked list since commit
1ae1602de0.
This commit uses configfs_add_default_group to fix this problem.
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
configfs: New of_overlay API
Add a mailbox-driven backlight controller for the Raspberry Pi DSI
touchscreen display. Requires updated GPU firmware to recognise the
mailbox request.
Signed-off-by: Gordon Hollingworth <gordon@raspberrypi.org>
Add Raspberry Pi firmware driver to the dependencies of backlight driver
Otherwise the backlight driver fails to build if the firmware
loading driver is not in the kernel
Signed-off-by: Alex Riesen <alexander.riesen@cetitec.com>
The driver crashed while a NULL pointer returned by i2c_get_adapter()
has been used to access the i2c bus functions.
The headphone probing function hb_hp_probe() now returns -EPROBE_DEFER
in case the i2c module has not been loaded yet.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
ASoC: Add support for Rpi-DAC
ASoC: Add prompt for ICS43432 codec
Without a prompt string, a config setting can't be included in a
defconfig. Give CONFIG_SND_SOC_ICS43432 a prompt so that Pi soundcards
can use the driver.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Add IQaudIO Sound Card support for Raspberry Pi
Set a limit of 0dB on Digital Volume Control
The main volume control in the PCM512x DAC has a range up to
+24dB. This is dangerously loud and can potentially cause massive
clipping in the output stages. Therefore this sets a sensible
limit of 0dB for this control.
Allow up to 24dB digital gain to be applied when using IQAudIO DAC+
24db_digital_gain DT param can be used to specify that PCM512x
codec "Digital" volume control should not be limited to 0dB gain,
and if specified will allow the full 24dB gain.
Modify IQAudIO DAC+ ASoC driver to set card/dai config from dt
Add the ability to set the card name, dai name and dai stream name, from
dt config.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
IQaudIO: auto-mute for AMP+ and DigiAMP+
IQAudIO amplifier mute via GPIO22. Add dt params for "one-shot" unmute
and auto mute.
Revision 2, auto mute implementing HiassofT suggestion to mute/unmute
using set_bias_level, rather than startup/shutdown....
"By default DAPM waits 5 seconds (pmdown_time) before shutting down
playback streams so a close/stop immediately followed by open/start
doesn't trigger an amp mute+unmute."
Tested on both AMP+ (via DAC+) and DigiAMP+, with both options...
dtoverlay=iqaudio-dacplus,unmute_amp
"one-shot" unmute when kernel module loads.
dtoverlay=iqaudio-dacplus,auto_mute_amp
Unmute amp when ALSA device opened by a client. Mute, with 5 second delay
when ALSA device closed. (Re-opening the device within the 5 second close
window, will cancel mute.)
Revision 4, using gpiod.
Revision 5, clean-up formatting before adding mute code.
- Convert tab plus 4 space formatting to 2x tab
- Remove '// NOT USED' commented code
Revision 6, don't attempt to "one-shot" unmute amp, unless card is
successfully registered.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
ASoC: iqaudio-dac: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: iqaudio-dac: use modern dai_link style
Signed-off-by: Matthias Reichl <hias@horus.com>
Added support for HiFiBerry DAC+
The driver is based on the HiFiBerry DAC driver. However HiFiBerry DAC+ uses
a different codec chip (PCM5122), therefore a new driver is necessary.
Add support for the HiFiBerry DAC+ Pro.
The HiFiBerry DAC+ and DAC+ Pro products both use the existing bcm sound driver with the DAC+ Pro having a special clock device driver representing the two high precision oscillators.
An addition bug fix is included for the PCM512x codec where by the physical size of the sample frame is used in the calculation of the LRCK divisor as it was found to be wrong when using 24-bit depth sample contained in a little endian 4-byte sample frame.
Limit PCM512x "Digital" gain to 0dB by default with HiFiBerry DAC+
24db_digital_gain DT param can be used to specify that PCM512x
codec "Digital" volume control should not be limited to 0dB gain,
and if specified will allow the full 24dB gain.
Add dt param to force HiFiBerry DAC+ Pro into slave mode
"dtoverlay=hifiberry-dacplus,slave"
Add 'slave' param to use HiFiBerry DAC+ Pro in slave mode,
with Pi as master for bit and frame clock.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
Fixed a bug when using 352.8kHz sample rate
Signed-off-by: Daniel Matuschek <daniel@hifiberry.com>
ASoC: pcm512x: revert downstream changes
This partially reverts commit 185ea05465
which was added by https://github.com/raspberrypi/linux/pull/1152
The downstream pcm512x changes caused a regression, it broke normal
use of the 24bit format with the codec, eg when using simple-audio-card.
The actual bug with 24bit playback is the incorrect usage
of physical_width in various drivers in the downstream tree
which causes 24bit data to be transmitted with 32 clock
cycles. So it's not the pcm512x that needs fixing, it's the
soundcard drivers.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: hifiberry_dacplus: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: hifiberry_dacplus: transmit S24_LE with 64 BCLK cycles
Signed-off-by: Matthias Reichl <hias@horus.com>
hifiberry_dacplus: switch to snd_soc_dai_set_bclk_ratio
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: hifiberry_dacplus: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add driver for rpi-proto
Forward port of 3.10.x driver from https://github.com/koalo
We are using a custom board and would like to use rpi 3.18.x
kernel. Patch works fine for our embedded system.
URL to the audio chip:
http://www.mikroe.com/add-on-boards/audio-voice/audio-codec-proto/
Playback tested with devicetree enabled.
Signed-off-by: Waldemar Brodkorb <wbrodkorb@conet.de>
ASoC: rpi-proto: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add Support for JustBoom Audio boards
justboom-dac: Adjust for ALSA API change
As of 4.4, snd_soc_limit_volume now takes a struct snd_soc_card *
rather than a struct snd_soc_codec *.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
ASoC: justboom-dac: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Also remove hw_params as it's no longer needed.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: justboom-dac: use modern dai_link style
Signed-off-by: Matthias Reichl <hias@horus.com>
New AudioInjector.net Pi soundcard with low jitter audio in and out.
Contains the sound/soc/bcm ALSA machine driver and necessary alterations to the Kconfig and Makefile.
Adds the dts overlay and updates the Makefile and README.
Updates the relevant defconfig files to enable building for the Raspberry Pi.
Thanks to Phil Elwell (pelwell) for the review, simple-card concepts and discussion. Thanks to Clive Messer for overlay naming suggestions.
Added support for headphones, microphone and bclk_ratio settings.
This patch adds headphone and microphone capability to the Audio Injector sound card. The patch also sets the bit clock ratio for use in the bcm2835-i2s driver. The bcm2835-i2s can't handle an 8 kHz sample rate when the bit clock is at 12 MHz because its register is only 10 bits wide which can't represent the ch2 offset of 1508. For that reason, the rate constraint is added.
ASoC: audioinjector-pi-soundcard: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
New driver for RRA DigiDAC1 soundcard using WM8741 + WM8804
ASoC: digidac1-soundcard: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add support for Dion Audio LOCO DAC-AMP HAT
Using dedicated machine driver and pcm5102a codec driver.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
ASoC: dionaudio_loco: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Allo Piano DAC boards: Initial 2 channel (stereo) support (#1645)
Add initial 2 channel (stereo) support for Allo Piano DAC (2.0/2.1) boards,
using allo-piano-dac-pcm512x-audio overlay and allo-piano-dac ALSA ASoC
machine driver.
NB. The initial support is 2 channel (stereo) ONLY!
(The Piano DAC 2.1 will only support 2 channel (stereo) left/right output,
pending an update to the upstream pcm512x codec driver, which will have
to be submitted via upstream. With the initial downstream support,
provided by this patch, the Piano DAC 2.1 subwoofer outputs will
not function.)
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net>
Signed-off-by: Clive Messer <clive.messer@digitaldreamtime.co.uk>
Tested-by: Clive Messer <clive.messer@digitaldreamtime.co.uk>
ASoC: allo-piano-dac: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Also remove hw_params and ops as they are no longer needed.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: allo-piano-dac: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add support for Allo Piano DAC 2.1 plus add-on board for Raspberry Pi.
The Piano DAC 2.1 has support for 4 channels with subwoofer.
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net>
Reviewed-by: Vijay Kumar B. <vijaykumar@zilogic.com>
Reviewed-by: Raashid Muhammed <raashidmuhammed@zilogic.com>
Add clock changes and mute gpios (#1938)
Also improve code style and adhere to ALSA coding conventions.
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net>
Reviewed-by: Vijay Kumar B. <vijaykumar@zilogic.com>
Reviewed-by: Raashid Muhammed <raashidmuhammed@zilogic.com>
PianoPlus: Dual Mono & Dual Stereo features added (#2069)
allo-piano-dac-plus: Master volume added + fixes
Master volume added, which controls both DACs volumes.
See: https://github.com/raspberrypi/linux/pull/2149
Also fix initial max volume, default mode value, and unmute.
Signed-off-by: allocom <sparky-dev@allo.com>
ASoC: allo-piano-dac-plus: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Signed-off-by: Matthias Reichl <hias@horus.com>
sound: bcm: Fix memset dereference warning
This warning appears with GCC 6.4.0 from toolchains.bootlin.com:
../sound/soc/bcm/allo-piano-dac-plus.c: In function ‘snd_allo_piano_dac_init’:
../sound/soc/bcm/allo-piano-dac-plus.c:711:30: warning: argument to ‘sizeof’ in ‘memset’ call is the same expression as the destination; did you mean to dereference it? [-Wsizeof-pointer-memaccess]
memset(glb_ptr, 0x00, sizeof(glb_ptr));
^
Suggested-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
ASoC: allo-piano-dac-plus: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add support for Allo Boss DAC add-on board for Raspberry Pi. (#1924)
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net>
Reviewed-by: Deepak <deepak@zilogic.com>
Reviewed-by: BabuSubashChandar <babusubashchandar@zilogic.com>
Add support for new clock rate and mute gpios.
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net>
Reviewed-by: Deepak <deepak@zilogic.com>
Reviewed-by: BabuSubashChandar <babusubashchandar@zilogic.com>
ASoC: allo-boss-dac: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: allo-boss-dac: transmit S24_LE with 64 BCLK cycles
Signed-off-by: Matthias Reichl <hias@horus.com>
allo-boss-dac: switch to snd_soc_dai_set_bclk_ratio
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: allo-boss-dac: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Support for Blokas Labs pisound board
Pisound dynamic overlay (#1760)
Restructuring pisound-overlay.dts, so it can be loaded and unloaded dynamically using dtoverlay.
Print a logline when the kernel module is removed.
pisound improvements:
* Added a writable sysfs object to enable scripts / user space software
to blink MIDI activity LEDs for variable duration.
* Improved hw_param constraints setting.
* Added compatibility with S16_LE sample format.
* Exposed some simple placeholder volume controls, so the card appears
in volumealsa widget.
Add missing SND_PISOUND selects dependency to SND_RAWMIDI
Without it the Pisound module fails to compile.
See https://github.com/raspberrypi/linux/issues/2366
Updates for Pisound module code:
* Merged 'Fix a warning in DEBUG builds' (1c8b82b).
* Updating some strings and copyright information.
* Fix for handling high load of MIDI input and output.
* Use dual rate oversampling ratio for 96kHz instead of single
rate one.
Signed-off-by: Giedrius Trainavicius <giedrius@blokas.io>
Fixing memset call in pisound.c
Signed-off-by: Giedrius Trainavicius <giedrius@blokas.io>
Fix for Pisound's MIDI Input getting blocked for a while in rare cases.
There was a possible race condition which could lead to Input's FIFO queue
to be underflown, causing high amount of processing in the worker thread for
some period of time.
Signed-off-by: Giedrius Trainavicius <giedrius@blokas.io>
Fix for Pisound kernel module in Real Time kernel configuration.
When handler of data_available interrupt is fired, queue_work ends up
getting called and it can block on a spin lock which is not allowed in
interrupt context. The fix was to run the handler from a thread context
instead.
Pisound: Remove spinlock usage around spi_sync
ASoC: pisound: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
ASoC: pisound: fix the parameter for spi_device_match
Signed-off-by: Hui Wang <hui.wang@canonical.com>
ASoC: Add driver for Cirrus Logic Audio Card
Note: due to problems with deferred probing of regulators
the following softdep should be added to a modprobe.d file
softdep arizona-spi pre: arizona-ldo1
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: rpi-cirrus: use modern dai_link style
Signed-off-by: Matthias Reichl <hias@horus.com>
sound: Support for Dion Audio LOCO-V2 DAC-AMP HAT
Signed-off-by: Miquel Blauw <info@dionaudio.nl>
ASoC: dionaudio_loco-v2: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Also remove hw_params and ops as they are no longer needed.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: dionaudio_loco-v2: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add support for Fe-Pi audio sound card. (#1867)
Fe-Pi Audio Sound Card is based on NXP SGTL5000 codec.
Mechanical specification of the board is the same the Raspberry Pi Zero.
3.5mm jacks for Headphone/Mic, Line In, and Line Out.
Signed-off-by: Henry Kupis <fe-pi@cox.net>
ASoC: fe-pi-audio: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add support for the AudioInjector.net Octo sound card
AudioInjector Octo: sample rates, regulators, reset
This patch adds new sample rates to the Audioinjector Octo sound card. The
new supported rates are (in kHz) :
96, 48, 32, 24, 16, 8, 88.2, 44.1, 29.4, 22.05, 14.7
Reference the bcm270x DT regulators in the overlay.
This patch adds a reset GPIO for the AudioInjector.net octo sound card.
Audioinjector octo : Make the playback and capture symmetric
This patch ensures that the sample rate and channel count of the audioinjector
octo sound card are symmetric.
audioinjector-octo: Add continuous clock feature
By user request, add a switch to prevent the clocks being stopped when
the stream is paused, stopped or shutdown. Provide access to the switch
by adding a 'non-stop-clocks' parameter to the audioinjector-addons
overlay.
See: https://github.com/raspberrypi/linux/issues/2409
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
sound: Fixes for audioinjector-octo under 4.19
1. Move the DT alias declaration to the I2C shim in the cases
where the shim is enabled. This works around a problem caused by a
4.19 commit [1] that generates DT/OF uevents for I2C drivers.
2. Fix the diagnostics in an error path of the soundcard driver to
correctly identify the reason for the failure to load.
3. Move the declaration of the clock node in the overlay outside
the I2C node to avoid warnings.
4. Sort the overlay nodes so that dependencies are only to earlier
fragments, in an attempt to get runtime dtoverlay application to
work (it still doesn't...)
See: https://github.com/Audio-Injector/Octo/issues/14
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
[1] af503716ac ("i2c: core: report OF style module alias for devices registered via OF")
ASoC: audioinjector-octo-soundcard: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Driver support for Google voiceHAT soundcard.
ASoC: googlevoicehat-codec: Use correct device when grabbing GPIO
The fixup for the VoiceHAT in 4.18 incorrectly tried to find the
sdmode GPIO pin under the card device, not the codec device.
This failed, and therefore caused the device probe to fail.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
ASoC: googlevoicehat-codec: Reformat for kernel coding standards
Fix all whitespace, indentation, and bracing errors.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
ASoC: googlevoicehat-codec: Make driver function structure const
Make voicehat_component_driver a const structure.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
ASoC: googlevoicehat-codec: Only convert from ms to jiffies once
Minor optimisation and allows to become checkpatch clean.
A msec value is read out of DT or from a define, and convert once to
jiffies, rather than every time that it is used.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Driver and overlay for Allo Katana DAC
Allo Katana DAC: Updated default values
Signed-off-by: Jaikumar <jaikumar@cem-solutions.com>
Added mute stream func
Signed-off-by: Jaikumar <jaikumar@cem-solutions.net>
codecs: Correct Katana minimum volume
Update Katana minimum volume to get the exact 0.5 dB value in each step.
Signed-off-by: Sudeep Kumar <sudeepkumar@cem-solutions.net>
ASoC: Add generic RPI driver for simple soundcards.
The RPI simple sound card driver provides a generic ALSA SOC card driver
supporting a variety of Pi HAT soundcards. The intention is to avoid
the duplication of code for cards that can't be fully supported by
the soc simple/graph cards but are otherwise almost identical.
This initial commit adds support for the ADAU1977 ADC, Google VoiceHat,
HifiBerry AMP, HifiBerry DAC and RPI DAC.
Signed-off-by: Tim Gover <tim.gover@raspberrypi.org>
ASoC: Use correct card name in rpi-simple driver
Use the specific card name from drvdata instead of the snd_rpi_simple
rpi-simple-soundcard: Use nicer driver name "RPi-simple"
Rename the driver from "RPI simple soundcard" to "RPi-simple" so that
the driver name won't be mangled allowing to be used unaltered as the
card conf filename.
ASoC: rpi-simple-soundcard: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
ASoC: Add Kconfig and Makefile for sound/soc/bcm
Signed-off-by: popcornmix <popcornmix@gmail.com>
ASoC: Create a generic Pi Hat WM8804 driver
Reduce the amount of duplicated code by creating a generic driver for
Pi Hat digi cards using the WM8804 codec.
This replaces the
Allo DigiOne, Hifiberry Digi/Pro, JustBoom Digi and IQAudIO Digi
dedicate soundcard drivers with a generic driver.
There are no significant changes to the runtime behavior of the drivers
and end users should not have to change any configuration settings
after upgrading.
Minor changes
* Check the return value of snd_soc_component_update_bits
* Added some pr_debug tracing
* Various checkpatch tidyups
* Updated allodigi-one to use use 128FS at > 96 Khz. This appears to
be an omission in the original driver code so followed the Hifiberry
DAC driver approach.
ASoC: rpi-wm8804-soundcard: use modern dai_link style
Signed-off-by: Matthias Reichl <hias@horus.com>
rpi-wm8804-soundcard: drop PWRDN register writes
Since kernel 4.0 the PWRDN register bits are under DAPM
control from the wm8804 driver.
Drop code that modifies that register to avoid interfering
with DAPM.
Signed-off-by: Matthias Reichl <hias@horus.com>
rpi-wm8804-soundcard: configure wm8804 clocks only on rate change
This should avoid clicks when stopping and immediately afterwards
starting a stream with the same samplerate as before.
Signed-off-by: Matthias Reichl <hias@horus.com>
rpi-wm8804-soundcard: Fixed MCLKDIV for Allo Digione
The Allo Digione board wants a fixed MCLKDIV of 256.
See: https://github.com/raspberrypi/linux/issues/3296
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
ASoC: Add support for AudioSense-Pi add-on soundcard
AudioSense-Pi is a RPi HAT based on a TI's TLV320AIC32x4 stereo codec
This hardware provides multiple audio I/O capabilities to the RPi.
The codec connects to the RPi's SoC through the I2S Bus.
The following devices can be connected through a 3.5mm jack
1. Line-In: Plain old audio in from mobile phones, PCs, etc.,
2. Mic-In: Connect a microphone
3. Line-Out: Connect the output to a speaker
4. Headphones: Connect a Headphone w or w/o microphones
Multiple Inputs:
It supports the following combinations
1. Two stereo Line-Inputs and a microphone
2. One stereo Line-Input and two microphones
3. Two stereo Line-Inputs, a microphone and
one mono line-input (with h/w hack)
4. One stereo Line-Input, two microphones and
one mono line-input (with h/w hack)
Multiple Outputs:
Audio output can be routed to the headphones or
speakers (with additional hardware)
Signed-off-by: b-ak <anur.bhargav@gmail.com>
ASoC: audiosense-pi: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Added driver for the HiFiBerry DAC+ ADC (#2694)
Signed-off-by: Daniel Matuschek <daniel@hifiberry.com>
hifiberry_dacplusadc: switch to snd_soc_dai_set_bclk_ratio
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: hifiberry_dacplusadc: fix DAI link setup
The driver only defines a single DAI link and the code that tries
to setup the second (non-existent) DAI link looks wrong - using dmic
as a CPU/platform driver doesn't make any sense.
The DT overlay doesn't define a dmic property, so the code was never
executed (otherwise it would have resulted in a memory corruption).
So drop the offending code to prevent issues if a dmic property
should be added to the DT overlay.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: hifiberry_dacplusadc: use modern dai_link style
Signed-off-by: Matthias Reichl <hias@horus.com>
Audiophonics I-Sabre 9038Q2M DAC driver
Signed-off-by: Audiophonics <contact@audiophonics.fr>
ASoC: i-sabre-q2m: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Added IQaudIO Pi-Codec board support (#2969)
Add support for the IQaudIO Pi-Codec board.
Signed-off-by: Gordon <gordon@iqaudio.com>
Fixed 48k timing issue
ASoC: iqaudio-codec: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
adds the Hifiberry DAC+ADC PRO version
This adds the driver for the DAC+ADC PRO version of the Hifiberry soundcard with software controlled PCM1863 ADC
Signed-off-by: Joerg Schambacher joerg@i2audio.com
Add Hifiberry DAC+DSP soundcard driver (#3224)
Adds the driver for the Hifiberry DAC+DSP. It supports capture and
playback depending on the DSP firmware.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
Allow simultaneous use of JustBoom DAC and Digi
Signed-off-by: Johannes Krude <johannes@krude.de>
Pisound: MIDI communication fixes for scaled down CPU.
* Increased maximum SPI communication speed to avoid running too slow
when the CPU is scaled down and losing MIDI data.
* Keep track of buffer usage in millibytes for higher precision.
Signed-off-by: Giedrius Trainavičius <giedrius@blokas.io>
sound: Add the HiFiBerry DAC+HD version
This adds the driver for the DAC+HD version supporting HiFiBerry's
PCM179x based DACs. It also adds PLL control for clock generation.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
Fix master mode settings of HiFiBerry DAC+ADC PRO card (#3424)
This patch fixes the board DAI setting when in master-mode.
Wrong setting could have caused random pop noise.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
adds LED OFF feature to HiFiBerry DAC+ADC PRO sound card
This adds a DT overlay parameter 'leds_off' which allows
to switch off the onboard activity LEDs at all times
which has been requested by some users.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
adds LED OFF feature to HiFiBerry DAC+ADC sound card
This adds a DT overlay parameter 'leds_off' which allows
to switch off the onboard activity LEDs at all times
which has been requested by some users.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
adds LED OFF feature to HiFiBerry DAC+/DAC+PRO sound cards
This adds a DT overlay parameter 'leds_off' which allows
to switch off the onboard activity LEDs at all times
which has been requested by some users.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
pisound: Added reading Pisound board hardware revision and exposing it (#3425)
pisound: Added reading Pisound board hardware revision and exposing it in kernel log and sysfs file:
/sys/kernel/pisound/hw_version
Signed-off-by: Giedrius <giedrius@blokas.io>
Added driver for HiFiBerry Amp amplifier add-on board
The driver contains a low-level hardware driver for the TAS5713 and the
drivers for the Raspberry Pi I2S subsystem.
TAS5713: return error if initialisation fails
Existing TAS5713 driver logs errors during initialisation, but does not return
an error code. Therefore even if initialisation fails, the driver will still be
loaded, but won't work. This patch fixes this. I2C communication error will now
reported correctly by a non-zero return code.
HiFiBerry Amp: fix device-tree problems
Some code to load the driver based on device-tree-overlays was missing. This is added by this patch.
According to 5713 pdf doc CLOCK_CTRL is a readonly status register, and it behaves so. Remove useless setting
sound: pcm512x-codec: Adding 352.8kHz samplerate support
sound/soc: only first codec is master in multicodec setup
When using multiple codecs, at most one codec should generate the master
clock. All codecs except the first are therefore configured for slave
mode.
Signed-off-by: Johannes Krude <johannes@krude.de>
ASoC: Fix snd_soc_get_pcm_runtime usage
Commit [1] changed the snd_soc_get_pcm_runtime to take a dai_link
pointer instead of a string. Patch up the downstream drivers to use
the modified API.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
[1] 4468189ff3 ("ASoC: soc-core: find rtd via dai_link pointer at snd_soc_get_pcm_runtime()")
Add support for the AudioInjector.net Isolated sound card
This patch adds support for the Audio Injector Isolated sound card.
Signed-off-by: Matt Flax <flatmax@flatmax.org>
Add support for merus-amp soundcard and ma120x0p codec
Add 96KHz rate support to MA120X0P codec and make enable and mute gpio
pins optional.
Signed-off-by: AMuszkat <ariel.muszkat@gmail.com>
Fixes a problem with clock settings of HiFiBerry DAC+ADC PRO (#3545)
This patch fixes a problem of the re-calculation of
i2s-clock and -parameter settings when only the ADC is activated.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
configs: Enable the AD193x codecs
See: https://github.com/raspberrypi/linux/issues/2850
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Switch to snd_soc_dai_set_bclk_ratio
Replaces obsolete function snd_soc_dai_set_tdm_slot
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
Enhances the DAC+ driver to control the optional headphone amplifier
Probes on the I2C bus for TPA6130A2, if successful, it sets DT-parameter
'status' from 'disabled' to 'okay' using change_sets to enable
the headphone control.
Signed-off-by: Joerg Schambacher joerg@i2audio.com
The Raspberry Pi firmware manages the power-down and reboot
process. To do this it installs a pm_power_off handler, causing
the gpio-poweroff module to abort the probe function.
This patch introduces a "force" DT property that overrides that
behaviour, and also adds a DT overlay to enable and control it.
Note that running in an active-low configuration (DT parameter
"active_low") requires a custom dt-blob.bin and probably won't
allow a reboot without switching off, so an external inversion
of the trigger signal may be preferable.
Provide a __copy_from_user that uses memcpy. On BCM2708, use
optimised memcpy/memmove/memcmp/memset implementations.
arch/arm: Add mmiocpy/set aliases for memcpy/set
See: https://github.com/raspberrypi/linux/issues/1082
copy_from_user: CPU_SW_DOMAIN_PAN compatibility
The downstream copy_from_user acceleration must also play nice with
CONFIG_CPU_SW_DOMAIN_PAN.
See: https://github.com/raspberrypi/linux/issues/1381
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Fix copy_from_user if BCM2835_FAST_MEMCPY=n
The change which introduced CONFIG_BCM2835_FAST_MEMCPY unconditionally
changed the behaviour of arm_copy_from_user. The page pinning code
is not safe on ARMv7 if LPAE & high memory is enabled and causes
crashes which look like PTE corruption.
Make __copy_from_user_memcpy conditional on CONFIG_2835_FAST_MEMCPY=y
which is really an ARMv6 / Pi1 optimization and not necessary on newer
ARM processors.
arm: fix mmap unlocks in uaccess_with_memcpy.c
This is a regression that was added with the commit 192a4e923e as of rpi-5.8.y, since that is when the move to the mmap locking API was introduced - d8ed45c5dc
The issue is that when the patch to improve performance for the __copy_to_user and __copy_from_user functions were added for the Raspberry Pi, some of the mmaps were incorrectly mapped to write instead of read. This would cause a verity of issues, and in my case, prevent the booting of a squashfs filesystem on rpi-5.8-y and above. An example of the panic you would see from this can be seen at https://pastebin.com/raw/jBz5xCzL
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Christopher Blake <chrisrblake93@gmail.com>
The "input" trigger makes the associated GPIO an input. This is to support
the Raspberry Pi PWR LED, which is driven by external hardware in normal use.
N.B. pwr_led is not available on Model A or B boards.
leds-gpio: Implement the brightness_get method
The power LED uses some clever logic that means it is driven
by a voltage measuring circuit when configured as input, otherwise
it is driven by the GPIO output value. This patch wires up the
brightness_get method for leds-gpio so that user-space can monitor
the LED value via /sys/class/gpio/led1/brightness. Using the input
trigger this returns an indication of the system power health,
otherwise it is just whatever value the trigger has written most
recently.
See: https://github.com/raspberrypi/linux/issues/1064
Add the bare minimum needed to boot BCM2708 from a Device Tree.
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
BCM2708: DT: change 'axi' nodename to 'soc'
Change DT node named 'axi' to 'soc' so it matches ARCH_BCM2835.
The VC4 bootloader fills in certain properties in the 'axi' subtree,
but since this is part of an upstreaming effort, the name is changed.
Signed-off-by: Noralf Tronnes notro@tronnes.org
BCM2708_DT: Correct length of the peripheral space
Use dts-dirs feature for overlays.
The kernel makefiles have a dts-dirs target that is for vendor subdirectories.
Using this fixes the install_dtbs target, which previously did not install the overlays.
BCM270X_DT: configure I2S DMA channels
Signed-off-by: Matthias Reichl <hias@horus.com>
BCM270X_DT: switch to bcm2835-i2s
I2S soundcard drivers with proper devicetree support (i.e. not linking
to the cpu_dai/platform via name but to cpu/platform via of_node)
will work out of the box without any modifications.
When the kernel is compiled without devicetree support the platform
code will instantiate the bcm2708-i2s driver and I2S soundcard drivers
will link to it via name, as before.
Signed-off-by: Matthias Reichl <hias@horus.com>
SDIO-overlay: add poll_once-boolean parameter
Add paramter to toggle sdio-device-polling
done every second or once at boot-time.
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
BCM270X_DT: Make mmc overlay compatible with current firmware
The original DT overlay logic followed a merge-then-patch procedure,
i.e. parameters are applied to the loaded overlay before the overlay
is merged into the base DTB. This sequence has been changed to
patch-then-merge, in order to support parameterised node names, and
to protect against bad overlays. As a result, overrides (parameters)
must only target labels in the overlay, but the overlay can obviously target nodes in the base DTB.
mmc-overlay.dts (that switches back to the original mmc sdcard
driver) is the only overlay violating that rule, and this patch
fixes it.
bcm270x_dt: Use the sdhost MMC controller by default
The "mmc" overlay reverts to using the other controller.
squash: Add cprman to dt
BCM270X_DT: Use clk_core for I2C interfaces
BCM270X_DT: Use bcm283x.dtsi, bcm2835.dtsi and bcm2836.dtsi
The mainline Device Tree files are quite close to downstream now.
Let's use bcm283x.dtsi, bcm2835.dtsi and bcm2836.dtsi as base files
for our dts files.
Mainline dts files are based on these files:
bcm2835-rpi.dtsi
bcm2835.dtsi bcm2836.dtsi
bcm283x.dtsi
Current downstream are based on these:
bcm2708.dtsi bcm2709.dtsi bcm2710.dtsi
bcm2708_common.dtsi
This patch introduces this dependency:
bcm2708.dtsi bcm2709.dtsi
bcm2708-rpi.dtsi
bcm270x.dtsi
bcm2835.dtsi bcm2836.dtsi
bcm283x.dtsi
And:
bcm2710.dtsi
bcm2708-rpi.dtsi
bcm270x.dtsi
bcm283x.dtsi
bcm270x.dtsi contains the downstream bcm283x.dtsi diff.
bcm2708-rpi.dtsi is the downstream version of bcm2835-rpi.dtsi.
Other changes:
- The led node has moved from /soc/leds to /leds. This is not a problem
since the label is used to reference it.
- The clk_osc reg property changes from 6 to 3.
- The gpu nodes has their interrupt property set in the base file.
- the clocks label does not point to the /clocks node anymore, but
points to the cprman node. This is not a problem since the overlays
that use the clock node refer to it directly: target-path = "/clocks";
- some nodes now have 2 labels since mainline and downstream differs in
this respect: cprman/clocks, spi0/spi, gpu/vc4.
- some nodes doesn't have an explicit status = "okay" since they're not
disabled in the base file: watchdog and random.
- gpiomem doesn't need an explicit status = "okay".
- bcm2708-rpi-cm.dts got the hpd-gpios property from bcm2708_common.dtsi,
it's now set directly in that file.
- bcm2709-rpi-2-b.dts has the timer node moved from /soc/timer to /timer.
- Removed clock-frequency property on the bcm{2709,2710}.dtsi timer nodes.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270X_DT: Use raspberrypi-power to turn on USB power
Use the raspberrypi-power driver to turn on USB power.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270X_DT: Add a .dtbo target, use for overlays
Change the filenames and extensions to keep the pre-DDT style of
overlay (<name>-overlay.dtb) distinct from new ones that use a
different style of local fixups (<name>.dtbo), and to match other
platforms.
The RPi firmware uses the DDTK trailer atom to choose which type of
overlay to use for each kernel.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: Don't generate "linux,phandle" props
The EPAPR standard says to use "phandle" properties to store phandles,
rather than the deprecated "linux,phandle" version. By default, dtc
generates both, but adding "-H epapr" causes it to only generate
"phandle"s, saving some space and clutter.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: Add overlay for enc28j60 on SPI2
Works on SPI2 for compute module
BCM270X_DT: Add midi-uart0 overlay
MIDI requires 31.25kbaud, a baudrate unsupported by Linux. The
midi-uart0 overlay configures uart0 (ttyAMA0) to use a fake clock
so that requesting 38.4kbaud actually gets 31.25kbaud.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: Add i2c-sensor overlay
The i2c-sensor overlay is a container for various pressure and
temperature sensors, currently bmp085 and bmp280. The standalone
bmp085_i2c-sensor overlay is now deprecated.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: overlays/*-overlay.dtb -> overlays/*.dtbo (#1752)
We now create overlays as .dtbo files.
build: support for .dtbo files for dtb overlays
Kernel 4.4.6+ on RaspberryPi support .dtbo files for overlays, instead of .dtb.
Patch the kernel, which has faulty rules to generate .dtbo the way yocto does
Signed-off-by: Herve Jourdain <herve.jourdain@neuf.fr>
Signed-off-by: Khem Raj <raj.khem@gmail.com>
BCM270X: Drop position requirement for CMA in VC4 overlay.
No longer necessary since 2aefcd5761,
and will probably let peeople that want to choose a larger CMA
allocation (particularly on pi0/1).
Signed-off-by: Eric Anholt <eric@anholt.net>
BCM270X_DT: RPi Device Tree tidy
Use the upstream sdhost node, add thermal-zones, and factor out some
common elements.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
kbuild: Silence unhelpful DTC warnings
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: DT build rules no longer arch-specific
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Support booting without Device Tree.
Turn on USB power.
Load driver early because of lacking support for deferred probing
in many drivers.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
firmware: bcm2835: Don't turn on USB power
The raspberrypi-power driver is now used to turn on USB power.
This partly reverts commit:
firmware: bcm2835: Support ARCH_BCM270x
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Add module for accessing the mailbox property channel through
/dev/vcio. Was previously in bcm2708-vcio.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
char: vcio: Add compat ioctl handling
There was no compat ioctl handler, so 32 bit userspace on a
64 bit kernel failed as IOCTL_MBOX_PROPERTY used the size
of char*.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
char: vcio: Fail probe if rpi_firmware is not found.
Device Tree is now the only supported config mechanism, therefore
uncomment the block of code that fails the probe if the
firmware node can't be found.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
i2c-bcm2708: fixed baudrate
Fixed issue where the wrong CDIV value was set for baudrates below 3815 Hz (for 250MHz bus clock).
In that case the computed CDIV value was more than 0xffff. However the CDIV register width is only 16 bits.
This resulted in incorrect setting of CDIV and higher baudrate than intended.
Example: 3500Hz -> CDIV=0x11704 -> CDIV(16bit)=0x1704 -> 42430Hz
After correction: 3500Hz -> CDIV=0x11704 -> CDIV(16bit)=0xffff -> 3815Hz
The correct baudrate is shown in the log after the cdiv > 0xffff correction.
Perform I2C combined transactions when possible
Perform I2C combined transactions whenever possible, within the
restrictions of the Broadcomm Serial Controller.
Disable DONE interrupt during TA poll
Prevent interrupt from being triggered if poll is missed and transfer
starts and finishes.
i2c: Make combined transactions optional and disabled by default
i2c: bcm2708: add device tree support
Add DT support to driver and add to .dtsi file.
Setup pins in .dts file.
i2c is disabled by default.
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
bcm2708: don't register i2c controllers when using DT
The devices for the i2c controllers are in the Device Tree.
Only register devices when not using DT.
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
I2C: Only register the I2C device for the current board revision
i2c_bcm2708: Fix clock reference counting
Fix grabbing lock from atomic context in i2c driver
2 main changes:
- check for timeouts in the bcm2708_bsc_setup function as indicated by this comment:
/* poll for transfer start bit (should only take 1-20 polls) */
This implies that the setup function can now fail so account for this everywhere it's called
- Removed the clk_get_rate call from inside the setup function as it locks a mutex and that's not ok since we call it from under a spin lock.
i2c-bcm2708: When using DT, leave the GPIO setup to pinctrl
i2c-bcm2708: Increase timeouts to allow larger transfers
Use the timeout value provided by the I2C_TIMEOUT ioctl when waiting
for completion. The default timeout is 1 second.
See: https://github.com/raspberrypi/linux/issues/260
i2c-bcm2708/BCM270X_DT: Add support for I2C2
The third I2C bus (I2C2) is normally reserved for HDMI use. Careless
use of this bus can break an attached display - use with caution.
It is recommended to disable accesses by VideoCore by setting
hdmi_ignore_edid=1 or hdmi_edid_file=1 in config.txt.
The interface is disabled by default - enable using the
i2c2_iknowwhatimdoing DT parameter.
bcm2708-spi: Don't use static pin configuration with DT
Also remove superfluous error checking - the SPI framework ensures the
validity of the chip_select value.
i2c-bcm2708: Remove non-DT support
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Set the BSC_CLKT clock streching timeout to 35ms as per SMBus specs.
Fixes i2c_bcm2708: Write to FIFO correctly - v2 (#1574)
* i2c: fix i2c_bcm2708: Clear FIFO before sending data
Make sure FIFO gets cleared before trying to send
data in case of a repeated start (COMBINED=Y).
* i2c: fix i2c_bcm2708: Only write to FIFO when not full
Check if FIFO can accept data before writing.
To avoid a peripheral read on the last iteration of a loop,
both bcm2708_bsc_fifo_fill and ~drain are changed as well.
Signed-off-by: Luke Wren <wren6991@gmail.com>
MISC: bcm2835: smi: use clock manager and fix reload issues
Use clock manager instead of self-made clockmanager.
Also fix some error paths that showd up during development
(especially missing release of dma resources on rmmod)
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
bcm2835_smi: re-add dereference to fix DMA transfers
Signed-off-by: popcornmix <popcornmix@gmail.com>
BCM270x: Move vc_mem
Make the vc_mem module available for ARCH_BCM2835 by moving it.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
char: vc_mem: Fix up compat ioctls for 64bit kernel
compat_ioctl wasn't defined, so 32bit user/64bit kernel
always failed.
VC_MEM_IOC_MEM_PHYS_ADDR was defined with parameter size
unsigned long, so the ioctl cmd changes between sizes.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
char: vc_mem: Fix all coding style issues.
Cleans up all checkpatch errors in vc_mem.c and vc_mem.h
No functional change to the code.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
BCM2835 has two SD card interfaces. This driver uses the other one.
bcm2835-sdhost: Error handling fix, and code clarification
bcm2835-sdhost: Adding overclocking option
Allow a different clock speed to be substitued for a requested 50MHz.
This option is exposed using the "overclock_50" DT parameter.
Note that the sdhost interface is restricted to integer divisions of
core_freq, and the highest sensible option for a core_freq of 250MHz
is 84 (250/3 = 83.3MHz), the next being 125 (250/2) which is much too
high.
Use at your own risk.
bcm2835-sdhost: Round up the overclock, so 62 works for 62.5Mhz
Also only warn once for each overclock setting.
bcm2835-sdhost: Improve error handling and recovery
1) Expose the hw_reset method to the MMC framework, removing many
internal calls by the driver.
2) Reduce overclock setting on error.
3) Increase timeout to cope with high capacity cards.
4) Add properties and parameters to control pio_limit and debug.
5) Reduce messages at probe time.
bcm2835-sdhost: Further improve overclock back-off
bcm2835-sdhost: Clear HBLC for PIO mode
Also update pio_limit default in overlay README.
bcm2835-sdhost: Add the ERASE capability
See: https://github.com/raspberrypi/linux/issues/1076
bcm2835-sdhost: Ignore CRC7 for MMC CMD1
It seems that the sdhost interface returns CRC7 errors for CMD1,
which is the MMC-specific SEND_OP_COND. Returning these errors to
the MMC layer causes a downward spiral, but ignoring them seems
to be harmless.
bcm2835-mmc/sdhost: Remove ARCH_BCM2835 differences
The bcm2835-mmc driver (and -sdhost driver that copied from it)
contains code to handle SDIO interrupts in a threaded interrupt
handler rather than waking the MMC framework thread. The change
follows a patch from Russell King that adds the facility as the
preferred way of working.
However, the new code path is only present in ARCH_BCM2835
builds, which I have taken to be a way of testing the waters
rather than making the change across the board; I can't see
any technical reason why it wouldn't be enabled for MACH_BCM270X
builds. So this patch standardises on the ARCH_BCM2835 code,
removing the old code paths.
bcm2835-sdhost: Don't log timeout errors unless debug=1
The MMC card-discovery process generates timeouts. This is
expected behaviour, so reporting it to the user serves no purpose.
Suppress the reporting of timeout errors unless the debug flag
is on.
bcm2835-sdhost: Add workaround for odd behaviour on some cards
For reasons not understood, the sdhost driver fails when reading
sectors very near the end of some SD cards. The problem could
be related to the similar issue that reading the final sector
of any card as part of a multiple read never completes, and the
workaround is an extension of the mechanism introduced to solve
that problem which ensures those sectors are always read singly.
bcm2835-sdhost: Major revision
This is a significant revision of the bcm2835-sdhost driver. It
improves on the original in a number of ways:
1) Through the use of CMD23 for reads it appears to avoid problems
reading some sectors on certain high speed cards.
2) Better atomicity to prevent crashes.
3) Higher performance.
4) Activity logging included, for easier diagnosis in the event
of a problem.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Restore ATOMIC flag to PIO sg mapping
Allocation problems have been seen in a wireless driver, and
this is the only change which might have been responsible.
SQUASH: bcm2835-sdhost: Only claim one DMA channel
With both MMC controllers enabled there are few DMA channels left. The
bcm2835-sdhost driver only uses DMA in one direction at a time, so it
doesn't need to claim two channels.
See: https://github.com/raspberrypi/linux/issues/1327
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Workaround for "slow" sectors
Some cards have been seen to cause timeouts after certain sectors are
read. This workaround enforces a minimum delay between the stop after
reading one of those sectors and a subsequent data command.
Using CMD23 (SET_BLOCK_COUNT) avoids this problem, so good cards will
not be penalised by this workaround.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Firmware manages the clock divisor
The bcm2835-sdhost driver hands control of the CDIV clock divisor
register to matching firmware, allowing it to adjust to a changing
core clock. This removes the need to use the performance governor or
to enable io_is_busy on the on-demand governor in order to get the
best SD performance.
N.B. As SD clocks must be an integer divisor of the core clock, it is
possible that the SD clock for "turbo" mode can be different (even
lower) than "normal" mode.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Reset the clock in task context
Since reprogramming the clock can now involve a round-trip to the
firmware it must not be done at atomic context, and a tasklet
is not a task.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Don't exit cmd wait loop on error
The FAIL flag can be set in the CMD register before command processing
is complete, leading to spurious "failed to complete" errors. This has
the effect of promoting harmless CRC7 errors during CMD1 processing
into errors that can delay and even prevent booting.
Also:
1) Convert the last KERN_ERROR message in the register dumping to
KERN_INFO.
2) Remove an unnecessary reset call from bcm2835_sdhost_add_host.
See: https://github.com/raspberrypi/linux/pull/1492
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: mmc_card_blockaddr fix
Get the definition of mmc_card_blockaddr from drivers/mmc/core/card.h.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: New timer API
mmc: bcm2835-sdhost: Support underclocking
Support underclocking of the SD bus in two ways:
1. using the max-frequency DT property (which currently has no DT
parameter), and
2. using the exiting sd_overclock parameter.
The two methods differ slightly - in the former the MMC subsystem is
aware of the underclocking, while in the latter it isn't - but the
end results should be the same.
See: https://github.com/raspberrypi/linux/issues/2350
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
mmc: bcm2835-sdhost: Add include
highmem.h (needed for kmap_atomic) is pulled in by one of the other
include files, but only with some CONFIG settings. Make the inclusion
explicit to cater for cases where the CONFIG setting is absent.
See: https://github.com/raspberrypi/linux/issues/2366
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
mmc/bcm2835-sdhost: Recover from MMC_SEND_EXT_CSD
If the user issues an "mmc extcsd read", the SD controller receives
what it thinks is a SEND_IF_COND command with an unexpected data block.
The resulting operations leave the FSM stuck in READWAIT, a state which
persists until the MMC framework resets the controller, by which point
the root filesystem is likely to have been unmounted.
A less heavyweight solution is to detect the condition and nudge the
FSM by asserting the (self-clearing) FORCE_DATA_MODE bit.
N.B. This workaround was essentially discovered by accident and without
a full understanding the inner workings of the controller, so it is
fortunate that the "fix" only modifies error paths.
See: https://github.com/raspberrypi/linux/issues/2728
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
mmc: bcm2835-sdhost: Fix warnings on arm64
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Allow for sg entries that cross pages
The dma_complete handling code calculates a virtual address for a page
then adds an offset, but if the offset is more than a page and HIGHMEM
is in use then the summed address could be in an unmapped (or just
incorrect) page.
The upstream SDHOST driver allows for this possibility - copy the code
that does so.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Fix DMA channel leak on error/remove
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
mmc: bcm2835-sdhost: Support 64-bit physical addresses
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Replace obsolete struct timeval
struct timeval has been retired due to the impending linux 32-bit tv_sec
rollover (only 18 years to go) - timespec64 is the obvious replacement.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
mmc: Disable CMD23 transfers on all cards
Pending wire-level investigation of these types of transfers
and associated errors on bcm2835-mmc, disable for now. Fallback of
CMD18/CMD25 transfers will be used automatically by the MMC layer.
Reported/Tested-by: Gellert Weisz <gellert@raspberrypi.org>
mmc: bcm2835-mmc: enable DT support for all architectures
Both ARCH_BCM2835 and ARCH_BCM270x are built with OF now.
Enable Device Tree support for all architectures.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
mmc: bcm2835-mmc: fix probe error handling
Probe error handling is broken in several places.
Simplify error handling by using device managed functions.
Replace pr_{err,info} with dev_{err,info}.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2835-mmc: Add locks when accessing sdhost registers
bcm2835-mmc: Add range of debug options for slowing things down
bcm2835-mmc: Add option to disable some delays
bcm2835-mmc: Add option to disable MMC_QUIRK_BLK_NO_CMD23
bcm2835-mmc: Default to disabling MMC_QUIRK_BLK_NO_CMD23
bcm2835-mmc: Adding overclocking option
Allow a different clock speed to be substitued for a requested 50MHz.
This option is exposed using the "overclock_50" DT parameter.
Note that the mmc interface is restricted to EVEN integer divisions of
250MHz, and the highest sensible option is 63 (250/4 = 62.5), the
next being 125 (250/2) which is much too high.
Use at your own risk.
bcm2835-mmc: Round up the overclock, so 62 works for 62.5Mhz
Also only warn once for each overclock setting.
mmc: bcm2835-mmc: Make available on ARCH_BCM2835
Make the bcm2835-mmc driver available for use on ARCH_BCM2835.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270x_DT: add bcm2835-mmc entry
Add Device Tree entry for bcm2835-mmc.
In non-DT mode, don't add the device in the board file.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2835-mmc: Don't overwrite MMC capabilities from DT
bcm2835-mmc: Don't override bus width capabilities from devicetree
Take out the force setting of the MMC_CAP_4_BIT_DATA host capability
so that the result read from devicetree via mmc_of_parse() is
preserved.
bcm2835-mmc: Only claim one DMA channel
With both MMC controllers enabled there are few DMA channels left. The
bcm2835-mmc driver only uses DMA in one direction at a time, so it
doesn't need to claim two channels.
See: https://github.com/raspberrypi/linux/issues/1327
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-mmc: New timer API
mmc: bcm2835-mmc: Support underclocking
Support underclocking of the SD bus using the max-frequency DT property
(which currently has no DT parameter). The sd_overclock parameter
already provides another way to achieve the same thing which should be
equivalent in end result, but it is a bug not to support max-frequency
as well.
See: https://github.com/raspberrypi/linux/issues/2350
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
mmc/bcm2835: Recover from MMC_SEND_EXT_CSD
If the user issues an "mmc extcsd read", the SD controller receives
what it thinks is a SEND_IF_COND command with an unexpected data block.
The resulting operations leave the FSM stuck in READWAIT, a state which
persists until the MMC framework resets the controller, by which point
the root filesystem is likely to have been unmounted.
A less heavyweight solution is to detect the condition and nudge the
FSM by asserting the (self-clearing) FORCE_DATA_MODE bit.
N.B. This workaround was essentially discovered by accident and without
a full understanding the inner workings of the controller, so it is
fortunate that the "fix" only modifies error paths.
See: https://github.com/raspberrypi/linux/issues/2728
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-mmc: Fix DMA channel leak
The BCM2835 MMC host driver requests a DMA channel on probe but neglects
to release the channel in the probe error path and on driver unbind.
I'm seeing this happen on every boot of the Compute Module 3: On first
driver probe, DMA channel 2 is allocated and then leaked with a "could
not get clk, deferring probe" message. On second driver probe, channel 4
is allocated.
Fix it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
bcm2835-mmc: Fix struct mmc_host leak on probe
The BCM2835 MMC host driver requests the bus address of the host's
register map on probe. If that fails, the driver leaks the struct
mmc_host allocated earlier.
Fix it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
bcm2835-mmc: Fix duplicate free_irq() on remove
The BCM2835 MMC host driver requests its interrupt as a device-managed
resource, so the interrupt is automatically freed after the driver is
unbound.
However on driver unbind, bcm2835_mmc_remove() frees the interrupt
explicitly to avoid invocation of the interrupt handler after driver
structures have been torn down.
The interrupt is thus freed twice, leading to a WARN splat in
__free_irq(). Fix by not requesting the interrupt as a device-managed
resource.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
bcm2835-mmc: Handle mmc_add_host() errors
The BCM2835 MMC host driver calls mmc_add_host() but doesn't check its
return value. Errors occurring in that function are therefore not
handled. Fix it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
bcm2835-mmc: Deduplicate reset of driver data on remove
The BCM2835 MMC host driver sets the device's driver data pointer to
NULL on ->remove() even though the driver core subsequently does the
same in __device_release_driver(). Drop the duplicate assignment.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
bcm2835_mmc: Remove vestigial threaded IRQ
With SDIO processing now managed by the MMC framework with a
workqueue, the bcm2835_mmc driver no longer needs a threaded
IRQ.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Add missing dma_unmap_sg calls to free relevant swiotlb bounce buffers.
This prevents DMA leaks.
Signed-off-by: Yaroslav Rosomakho <yaroslavros@gmail.com>
Limit max_req_size under arm64 (or any other platform that uses swiotlb) to prevent potential buffer overflow due to bouncing.
Signed-off-by: Yaroslav Rosomakho <yaroslavros@gmail.com>
Add support for DMA controller of BCM2708 as used in the Raspberry Pi.
Currently it only supports cyclic DMA.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
dmaengine: expand functionality by supporting scatter/gather transfers sdhci-bcm2708 and dma.c: fix for LITE channels
DMA: fix cyclic LITE length overflow bug
dmaengine: bcm2708: Remove chancnt affectations
Mirror bcm2835-dma.c commit 9eba5536a7:
chancnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: overwrite dreq only if it is not set
dreq is set when the DMA channel is fetched from Device Tree.
slave_id is set using dmaengine_slave_config().
Only overwrite dreq with slave_id if it is not set.
dreq/slave_id in the cyclic DMA case is not touched, because I don't
have hardware to test with.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: do device registration in the board file
Don't register the device in the driver. Do it in the board file.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: don't restrict DT support to ARCH_BCM2835
Both ARCH_BCM2835 and ARCH_BCM270x are built with OF now.
Add Device Tree support to the non ARCH_BCM2835 case.
Use the same driver name regardless of architecture.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270x_DT: add bcm2835-dma entry
Add Device Tree entry for bcm2835-dma.
The entry doesn't contain any resources since they are handled
by the arch/arm/mach-bcm270x/dma.c driver.
In non-DT mode, don't add the device in the board file.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2708-dmaengine: Add debug options
BCM270x: Add memory and irq resources to dmaengine device and DT
Prepare for merging of the legacy DMA API arch driver dma.c
with bcm2708-dmaengine by adding memory and irq resources both
to platform file device and Device Tree node.
Don't use BCM_DMAMAN_DRIVER_NAME so we don't have to include mach/dma.h
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: Merge with arch dma.c driver and disable dma.c
Merge the legacy DMA API driver with bcm2708-dmaengine.
This is done so we can use bcm2708_fb on ARCH_BCM2835 (mailbox
driver is also needed).
Changes to the dma.c code:
- Use BIT() macro.
- Cutdown some comments to one line.
- Add mutex to vc_dmaman and use this, since the dev lock is locked
during probing of the engine part.
- Add global g_dmaman variable since drvdata is used by the engine part.
- Restructure for readability:
vc_dmaman_chan_alloc()
vc_dmaman_chan_free()
bcm_dma_chan_free()
- Restructure bcm_dma_chan_alloc() to simplify error handling.
- Use device irq resources instead of hardcoded bcm_dma_irqs table.
- Remove dev_dmaman_register() and code it directly.
- Remove dev_dmaman_deregister() and code it directly.
- Simplify bcm_dmaman_probe() using devm_* functions.
- Get dmachans from DT if available.
- Keep 'dma.dmachans' module argument name for backwards compatibility.
Make it available on ARCH_BCM2835 as well.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: set residue_granularity field
bcm2708-dmaengine supports residue reporting at burst level
but didn't report this via the residue_granularity field.
Without this field set properly we get playback issues with I2S cards.
dmaengine: bcm2708-dmaengine: Fix memory leak when stopping a running transfer
bcm2708-dmaengine: Use more DMA channels (but not 12)
1) Only the bcm2708_fb drivers uses the legacy DMA API, and
it requires a BULK-capable channel, so all other types
(FAST, NORMAL and LITE) can be made available to the regular
DMA API.
2) DMA channels 11-14 share an interrupt. The driver can't
handle this, so don't use channels 12-14 (12 was used, probably
because it appears to have an interrupt, but in reality that
interrupt is for activity on ANY channel). This may explain
a lockup encountered when running out of DMA channels.
The combined effect of this patch is to leave 7 DMA channels
available + channel 0 for bcm2708_fb via the legacy API.
See: https://github.com/raspberrypi/linux/issues/1110https://github.com/raspberrypi/linux/issues/1108
dmaengine: bcm2708: Make legacy API available for bcm2835-dma
bcm2708_fb uses the legacy DMA API, so in order to start using
bcm2835-dma, bcm2835-dma has to support the legacy API. Make this
possible by exporting bcm_dmaman_probe() and bcm_dmaman_remove().
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: Change DT compatible string
Both bcm2835-dma and bcm2708-dmaengine have the same compatible string.
So change compatible to "brcm,bcm2708-dma".
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: Remove driver but keep legacy API
Dropping non-DT support means we don't need this driver,
but we still need the legacy DMA API.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2708-dmaengine - Fix arm64 portability/build issues
dma-bcm2708: Fix module compilation of CONFIG_DMA_BCM2708
bcm2708-dmaengine.c defines functions like bcm_dma_start which are
defined as well in dma-bcm2708.h as inline versions when
CONFIG_DMA_BCM2708 is not defined. This works fine when
CONFIG_DMA_BCM2708 is built in, but when it is selected as module build
fails with redefinition errors because in the build system when
CONFIG_DMA_BCM2708 is selected as module, the macro becomes
CONFIG_DMA_BCM2708_MODULE.
This patch makes the header use CONFIG_DMA_BCM2708_MODULE too when
available.
Fixes https://github.com/raspberrypi/linux/issues/2056
Signed-off-by: Andrei Gherzan <andrei@gherzan.com>
Especially on platforms with a slower CPU but a relatively high
framebuffer fill bandwidth, like current ARM devices, the existing
console monochrome imageblit function used to draw console text is
suboptimal for common pixel depths such as 16bpp and 32bpp. The existing
code is quite general and can deal with several pixel depths. By creating
special case functions for 16bpp and 32bpp, by far the most common pixel
formats used on modern systems, a significant speed-up is attained
which can be readily felt on ARM-based devices like the Raspberry Pi
and the Allwinner platform, but should help any platform using the
fb layer.
The special case functions allow constant folding, eliminating a number
of instructions including divide operations, and allow the use of an
unrolled loop, eliminating instructions with a variable shift size,
reducing source memory access instructions, and eliminating excessive
branching. These unrolled loops also allow much better code optimization
by the C compiler. The code that selects which optimized variant is used
is also simplified, eliminating integer divide instructions.
The speed-up, measured by timing 'cat file.txt' in the console, varies
between 40% and 70%, when testing on the Raspberry Pi and Allwinner
ARM-based platforms, depending on font size and the pixel depth, with
the greater benefit for 32bpp.
Signed-off-by: Harm Hanemaaijer <fgenfb@yahoo.com>
Based on the patch authored by Ali Gholami Rudi at
https://lkml.org/lkml/2009/7/13/153
Provide an ioctl for userspace applications, but only if this operation
is hardware accelerated (otherwide it does not make any sense).
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
bcm2708_fb: Add ioctl for reading gpu memory through dma
video: bcm2708_fb: Add compat_ioctl support.
When using a 64 bit kernel with 32 bit userspace we need
compat ioctl handling for FBIODMACOPY as one of the
parameters is a pointer.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: popcornmix <popcornmix@gmail.com>
bcm2708_fb : Implement blanking support using the mailbox property interface
bcm2708_fb: Add pan and vsync controls
bcm2708_fb: DMA acceleration for fb_copyarea
Based on http://www.raspberrypi.org/phpBB3/viewtopic.php?p=62425#p62425
Also used Simon's dmaer_master module as a reference for tweaking DMA
settings for better performance.
For now busylooping only. IRQ support might be added later.
With non-overclocked Raspberry Pi, the performance is ~360 MB/s
for simple copy or ~260 MB/s for two-pass copy (used when dragging
windows to the right).
In the case of using DMA channel 0, the performance improves
to ~440 MB/s.
For comparison, VFP optimized CPU copy can only do ~114 MB/s in
the same conditions (hindered by reading uncached source buffer).
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
bcm2708_fb: report number of dma copies
Add a counter (exported via debugfs) reporting the
number of dma copies that the framebuffer driver
has done, in order to help evaluate different
optimization strategies.
Signed-off-by: Luke Diamand <luked@broadcom.com>
bcm2708_fb: use IRQ for DMA copies
The copyarea ioctl() uses DMA to speed things along. This
was busy-waiting for completion. This change supports using
an interrupt instead for larger transfers. For small
transfers, busy-waiting is still likely to be faster.
Signed-off-by: Luke Diamand <luke@diamand.org>
bcm2708: Make ioctl logging quieter
video: fbdev: bcm2708_fb: Don't panic on error
No need to panic the kernel if the video driver fails.
Just print a message and return an error.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
fbdev: bcm2708_fb: Add ARCH_BCM2835 support
Add Device Tree support.
Pass the device to dma_alloc_coherent() in order to get the
correct bus address on ARCH_BCM2835.
Use the new DMA legacy API header file.
Including <mach/platform.h> is not necessary.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270x_DT: Add bcm2708-fb device
Add bcm2708-fb to Device Tree and don't add the
platform device when booting in DT mode.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Cleanup of bcm2708_fb file to kernel coding standards
Some minor change to function - remove a use of
in_atomic, plus replacing various debug messages
that manually specify the function name with
("%s",.__func__)
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
video: bcm2708_fb: Try allocating on the ARM and passing to VPU
Currently the VPU allocates the contiguous buffer for the
framebuffer.
Try an alternate path first where we use dma_alloc_coherent
and pass the buffer to the VPU. Should the VPU firmware not
support that path, then free the buffer and revert to the
old behaviour of using the VPU allocation.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: popcornmix <popcornmix@gmail.com>
usb: dwc: fix lockdep false positive
Signed-off-by: Kari Suvanto <karis79@gmail.com>
usb: dwc: fix inconsistent lock state
Signed-off-by: Kari Suvanto <karis79@gmail.com>
Add FIQ patch to dwc_otg driver. Enable with dwc_otg.fiq_fix_enable=1. Should give about 10% more ARM performance.
Thanks to Gordon and Costas
Avoid dynamic memory allocation for channel lock in USB driver. Thanks ddv2005.
Add NAK holdoff scheme. Enabled by default, disable with dwc_otg.nak_holdoff_enable=0. Thanks gsh
Make sure we wait for the reset to finish
dwc_otg: fix bug in dwc_otg_hcd.c resulting in silent kernel
memory corruption, escalating to OOPS under high USB load.
dwc_otg: Fix unsafe access of QTD during URB enqueue
In dwc_otg_hcd_urb_enqueue during qtd creation, it was possible that the
transaction could complete almost immediately after the qtd was assigned
to a host channel during URB enqueue, which meant the qtd pointer was no
longer valid having been completed and removed. Usually, this resulted in
an OOPS during URB submission. By predetermining whether transactions
need to be queued or not, this unsafe pointer access is avoided.
This bug was only evident on the Pi model A where a device was attached
that had no periodic endpoints (e.g. USB pendrive or some wlan devices).
dwc_otg: Fix incorrect URB allocation error handling
If the memory allocation for a dwc_otg_urb failed, the kernel would OOPS
because for some reason a member of the *unallocated* struct was set to
zero. Error handling changed to fail correctly.
dwc_otg: fix potential use-after-free case in interrupt handler
If a transaction had previously aborted, certain interrupts are
enabled to track error counts and reset where necessary. On IN
endpoints the host generates an ACK interrupt near-simultaneously
with completion of transfer. In the case where this transfer had
previously had an error, this results in a use-after-free on
the QTD memory space with a 1-byte length being overwritten to
0x00.
dwc_otg: add handling of SPLIT transaction data toggle errors
Previously a data toggle error on packets from a USB1.1 device behind
a TT would result in the Pi locking up as the driver never handled
the associated interrupt. Patch adds basic retry mechanism and
interrupt acknowledgement to cater for either a chance toggle error or
for devices that have a broken initial toggle state (FT8U232/FT232BM).
dwc_otg: implement tasklet for returning URBs to usbcore hcd layer
The dwc_otg driver interrupt handler for transfer completion will spend
a very long time with interrupts disabled when a URB is completed -
this is because usb_hcd_giveback_urb is called from within the handler
which for a USB device driver with complicated processing (e.g. webcam)
will take an exorbitant amount of time to complete. This results in
missed completion interrupts for other USB packets which lead to them
being dropped due to microframe overruns.
This patch splits returning the URB to the usb hcd layer into a
high-priority tasklet. This will have most benefit for isochronous IN
transfers but will also have incidental benefit where multiple periodic
devices are active at once.
dwc_otg: fix NAK holdoff and allow on split transactions only
This corrects a bug where if a single active non-periodic endpoint
had at least one transaction in its qh, on frnum == MAX_FRNUM the qh
would get skipped and never get queued again. This would result in
a silent device until error detection (automatic or otherwise) would
either reset the device or flush and requeue the URBs.
Additionally the NAK holdoff was enabled for all transactions - this
would potentially stall a HS endpoint for 1ms if a previous error state
enabled this interrupt and the next response was a NAK. Fix so that
only split transactions get held off.
dwc_otg: Call usb_hcd_unlink_urb_from_ep with lock held in completion handler
usb_hcd_unlink_urb_from_ep must be called with the HCD lock held. Calling it
asynchronously in the tasklet was not safe (regression in
c4564d4a1a).
This change unlinks it from the endpoint prior to queueing it for handling in
the tasklet, and also adds a check to ensure the urb is OK to be unlinked
before doing so.
NULL pointer dereference kernel oopses had been observed in usb_hcd_giveback_urb
when a USB device was unplugged/replugged during data transfer. This effect
was reproduced using automated USB port power control, hundreds of replug
events were performed during active transfers to confirm that the problem was
eliminated.
USB fix using a FIQ to implement split transactions
This commit adds a FIQ implementaion that schedules
the split transactions using a FIQ so we don't get
held off by the interrupt latency of Linux
dwc_otg: fix device attributes and avoid kernel warnings on boot
dcw_otg: avoid logging function that can cause panics
See: https://github.com/raspberrypi/firmware/issues/21
Thanks to cleverca22 for fix
dwc_otg: mask correct interrupts after transaction error recovery
The dwc_otg driver will unmask certain interrupts on a transaction
that previously halted in the error state in order to reset the
QTD error count. The various fine-grained interrupt handlers do not
consider that other interrupts besides themselves were unmasked.
By disabling the two other interrupts only ever enabled in DMA mode
for this purpose, we can avoid unnecessary function calls in the
IRQ handler. This will also prevent an unneccesary FIQ interrupt
from being generated if the FIQ is enabled.
dwc_otg: fiq: prevent FIQ thrash and incorrect state passing to IRQ
In the case of a transaction to a device that had previously aborted
due to an error, several interrupts are enabled to reset the error
count when a device responds. This has the side-effect of making the
FIQ thrash because the hardware will generate multiple instances of
a NAK on an IN bulk/interrupt endpoint and multiple instances of ACK
on an OUT bulk/interrupt endpoint. Make the FIQ mask and clear the
associated interrupts.
Additionally, on non-split transactions make sure that only unmasked
interrupts are cleared. This caused a hard-to-trigger but serious
race condition when you had the combination of an endpoint awaiting
error recovery and a transaction completed on an endpoint - due to
the sequencing and timing of interrupts generated by the dwc_otg core,
it was possible to confuse the IRQ handler.
Fix function tracing
dwc_otg: whitespace cleanup in dwc_otg_urb_enqueue
dwc_otg: prevent OOPSes during device disconnects
The dwc_otg_urb_enqueue function is thread-unsafe. In particular the
access of urb->hcpriv, usb_hcd_link_urb_to_ep, dwc_otg_urb->qtd and
friends does not occur within a critical section and so if a device
was unplugged during activity there was a high chance that the
usbcore hub_thread would try to disable the endpoint with partially-
formed entries in the URB queue. This would result in BUG() or null
pointer dereferences.
Fix so that access of urb->hcpriv, enqueuing to the hardware and
adding to usbcore endpoint URB lists is contained within a single
critical section.
dwc_otg: prevent BUG() in TT allocation if hub address is > 16
A fixed-size array is used to track TT allocation. This was
previously set to 16 which caused a crash because
dwc_otg_hcd_allocate_port would read past the end of the array.
This was hit if a hub was plugged in which enumerated as addr > 16,
due to previous device resets or unplugs.
Also add #ifdef FIQ_DEBUG around hcd->hub_port_alloc[], which grows
to a large size if 128 hub addresses are supported. This field is
for debug only for tracking which frame an allocate happened in.
dwc_otg: make channel halts with unknown state less damaging
If the IRQ received a channel halt interrupt through the FIQ
with no other bits set, the IRQ would not release the host
channel and never complete the URB.
Add catchall handling to treat as a transaction error and retry.
dwc_otg: fiq_split: use TTs with more granularity
This fixes certain issues with split transaction scheduling.
- Isochronous multi-packet OUT transactions now hog the TT until
they are completed - this prevents hubs aborting transactions
if they get a periodic start-split out-of-order
- Don't perform TT allocation on non-periodic endpoints - this
allows simultaneous use of the TT's bulk/control and periodic
transaction buffers
This commit will mainly affect USB audio playback.
dwc_otg: fix potential sleep while atomic during urb enqueue
Fixes a regression introduced with eb1b482a. Kmalloc called from
dwc_otg_hcd_qtd_add / dwc_otg_hcd_qtd_create did not always have
the GPF_ATOMIC flag set. Force this flag when inside the larger
critical section.
dwc_otg: make fiq_split_enable imply fiq_fix_enable
Failing to set up the FIQ correctly would result in
"IRQ 32: nobody cared" errors in dmesg.
dwc_otg: prevent crashes on host port disconnects
Fix several issues resulting in crashes or inconsistent state
if a Model A root port was disconnected.
- Clean up queue heads properly in kill_urbs_in_qh_list by
removing the empty QHs from the schedule lists
- Set the halt status properly to prevent IRQ handlers from
using freed memory
- Add fiq_split related cleanup for saved registers
- Make microframe scheduling reclaim host channels if
active during a disconnect
- Abort URBs with -ESHUTDOWN status response, informing
device drivers so they respond in a more correct fashion
and don't try to resubmit URBs
- Prevent IRQ handlers from attempting to handle channel
interrupts if the associated URB was dequeued (and the
driver state was cleared)
dwc_otg: prevent leaking URBs during enqueue
A dwc_otg_urb would get leaked if the HCD enqueue function
failed for any reason. Free the URB at the appropriate points.
dwc_otg: Enable NAK holdoff for control split transactions
Certain low-speed devices take a very long time to complete a
data or status stage of a control transaction, producing NAK
responses until they complete internal processing - the USB2.0
spec limit is up to 500mS. This causes the same type of interrupt
storm as seen with USB-serial dongles prior to c8edb238.
In certain circumstances, usually while booting, this interrupt
storm could cause SD card timeouts.
dwc_otg: Fix for occasional lockup on boot when doing a USB reset
dwc_otg: Don't issue traffic to LS devices in FS mode
Issuing low-speed packets when the root port is in full-speed mode
causes the root port to stop responding. Explicitly fail when
enqueuing URBs to a LS endpoint on a FS bus.
Fix ARM architecture issue with local_irq_restore()
If local_fiq_enable() is called before a local_irq_restore(flags) where
the flags variable has the F bit set, the FIQ will be erroneously disabled.
Fixup arch_local_irq_restore to avoid trampling the F bit in CPSR.
Also fix some of the hacks previously implemented for previous dwc_otg
incarnations.
dwc_otg: fiq_fsm: Base commit for driver rewrite
This commit removes the previous FIQ fixes entirely and adds fiq_fsm.
This rewrite features much more complete support for split transactions
and takes into account several OTG hardware bugs. High-speed
isochronous transactions are also capable of being performed by fiq_fsm.
All driver options have been removed and replaced with:
- dwc_otg.fiq_enable (bool)
- dwc_otg.fiq_fsm_enable (bool)
- dwc_otg.fiq_fsm_mask (bitmask)
- dwc_otg.nak_holdoff (unsigned int)
Defaults are specified such that fiq_fsm behaves similarly to the
previously implemented FIQ fixes.
fiq_fsm: Push error recovery into the FIQ when fiq_fsm is used
If the transfer associated with a QTD failed due to a bus error, the HCD
would retry the transfer up to 3 times (implementing the USB2.0
three-strikes retry in software).
Due to the masking mechanism used by fiq_fsm, it is only possible to pass
a single interrupt through to the HCD per-transfer.
In this instance host channels would fall off the radar because the error
reset would function, but the subsequent channel halt would be lost.
Push the error count reset into the FIQ handler.
fiq_fsm: Implement timeout mechanism
For full-speed endpoints with a large packet size, interrupt latency
runs the risk of the FIQ starting a transaction too late in a full-speed
frame. If the device is still transmitting data when EOF2 for the
downstream frame occurs, the hub will disable the port. This change is
not reflected in the hub status endpoint and the device becomes
unresponsive.
Prevent high-bandwidth transactions from being started too late in a
frame. The mechanism is not guaranteed: a combination of bit stuffing
and hub latency may still result in a device overrunning.
fiq_fsm: fix bounce buffer utilisation for Isochronous OUT
Multi-packet isochronous OUT transactions were subject to a few bounday
bugs. Fix them.
Audio playback is now much more robust: however, an issue stands with
devices that have adaptive sinks - ALSA plays samples too fast.
dwc_otg: Return full-speed frame numbers in HS mode
The frame counter increments on every *microframe* in high-speed mode.
Most device drivers expect this number to be in full-speed frames - this
caused considerable confusion to e.g. snd_usb_audio which uses the
frame counter to estimate the number of samples played.
fiq_fsm: save PID on completion of interrupt OUT transfers
Also add edge case handling for interrupt transports.
Note that for periodic split IN, data toggles are unimplemented in the
OTG host hardware - it unconditionally accepts any PID.
fiq_fsm: add missing case for fiq_fsm_tt_in_use()
Certain combinations of bitrate and endpoint activity could
result in a periodic transaction erroneously getting started
while the previous Isochronous OUT was still active.
fiq_fsm: clear hcintmsk for aborted transactions
Prevents the FIQ from erroneously handling interrupts
on a timed out channel.
fiq_fsm: enable by default
fiq_fsm: fix dequeues for non-periodic split transactions
If a dequeue happened between the SSPLIT and CSPLIT phases of the
transaction, the HCD would never receive an interrupt.
fiq_fsm: Disable by default
fiq_fsm: Handle HC babble errors
The HCTSIZ transfer size field raises a babble interrupt if
the counter wraps. Handle the resulting interrupt in this case.
dwc_otg: fix interrupt registration for fiq_enable=0
Additionally make the module parameter conditional for wherever
hcd->fiq_state is touched.
fiq_fsm: Enable by default
dwc_otg: Fix various issues with root port and transaction errors
Process the host port interrupts correctly (and don't trample them).
Root port hotplug now functional again.
Fix a few thinkos with the transaction error passthrough for fiq_fsm.
fiq_fsm: Implement hack for Split Interrupt transactions
Hubs aren't too picky about which endpoint we send Control type split
transactions to. By treating Interrupt transfers as Control, it is
possible to use the non-periodic queue in the OTG core as well as the
non-periodic FIFOs in the hub itself. This massively reduces the
microframe exclusivity/contention that periodic split transactions
otherwise have to enforce.
It goes without saying that this is a fairly egregious USB specification
violation, but it works.
Original idea by Hans Petter Selasky @ FreeBSD.org.
dwc_otg: FIQ support on SMP. Set up FIQ stack and handler on Core 0 only.
dwc_otg: introduce fiq_fsm_spin(un|)lock()
SMP safety for the FIQ relies on register read-modify write cycles being
completed in the correct order. Several places in the DWC code modify
registers also touched by the FIQ. Protect these by a bare-bones lock
mechanism.
This also makes it possible to run the FIQ and IRQ handlers on different
cores.
fiq_fsm: fix build on bcm2708 and bcm2709 platforms
dwc_otg: put some barriers back where they should be for UP
bcm2709/dwc_otg: Setup FIQ on core 1 if >1 core active
dwc_otg: fixup read-modify-write in critical paths
Be more careful about read-modify-write on registers that the FIQ
also touches.
Guard fiq_fsm_spin_lock with fiq_enable check
fiq_fsm: Falling out of the state machine isn't fatal
This edge case can be hit if the port is disabled while the FIQ is
in the middle of a transaction. Make the effects less severe.
Also get rid of the useless return value.
squash: dwc_otg: Allow to build without SMP
usb: core: make overcurrent messages more prominent
Hub overcurrent messages are more serious than "debug". Increase loglevel.
usb: dwc_otg: Don't use dma_to_virt()
Commit 6ce0d20 changes dma_to_virt() which breaks this driver.
Open code the old dma_to_virt() implementation to work around this.
Limit the use of __bus_to_virt() to cases where transfer_buffer_length
is set and transfer_buffer is not set. This is done to increase the
chance that this driver will also work on ARCH_BCM2835.
transfer_buffer should not be NULL if the length is set, but the
comment in the code indicates that there are situations where this
might happen. drivers/usb/isp1760/isp1760-hcd.c also has a similar
comment pointing to a possible: 'usb storage / SCSI bug'.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: Fix crash when fiq_enable=0
dwc_otg: fiq_fsm: Make high-speed isochronous strided transfers work properly
Certain low-bandwidth high-speed USB devices (specialist audio devices,
compressed-frame webcams) have packet intervals > 1 microframe.
Stride these transfers in the FIQ by using the start-of-frame interrupt
to restart the channel at the right time.
dwc_otg: Force host mode to fix incorrect compute module boards
dwc_otg: Add ARCH_BCM2835 support
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: Simplify FIQ irq number code
Dropping ATAGS means we can simplify the FIQ irq number code.
Also add error checking on the returned irq number.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: Remove duplicate gadget probe/unregister function
dwc_otg: Properly set the HFIR
Douglas Anderson reported:
According to the most up to date version of the dwc2 databook, the FRINT
field of the HFIR register should be programmed to:
* 125 us * (PHY clock freq for HS) - 1
* 1000 us * (PHY clock freq for FS/LS) - 1
This is opposed to older versions of the doc that claimed it should be:
* 125 us * (PHY clock freq for HS)
* 1000 us * (PHY clock freq for FS/LS)
and reported lower timing jitter on a USB analyser
dcw_otg: trim xfer length when buffer larger than allocated size is received
dwc_otg: Don't free qh align buffers in atomic context
dwc_otg: Enable the hack for Split Interrupt transactions by default
dwc_otg.fiq_fsm_mask=0xF has long been a suggestion for users with audio stutters or other USB bandwidth issues.
So far we are aware of many success stories but no failure caused by this setting.
Make it a default to learn more.
See: https://www.raspberrypi.org/forums/viewtopic.php?f=28&t=70437
Signed-off-by: popcornmix <popcornmix@gmail.com>
dwc_otg: Use kzalloc when suitable
dwc_otg: Pass struct device to dma_alloc*()
This makes it possible to get the bus address from Device Tree.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: fix summarize urb->actual_length for isochronous transfers
Kernel does not copy input data of ISO transfers to userspace
if actual_length is set only in ISO transfers and not summarized
in urb->actual_length. Fixesraspberrypi/linux#903
fiq_fsm: Use correct states when starting isoc OUT transfers
In fiq_fsm_start_next_periodic() if an isochronous OUT transfer
was selected, no regard was given as to whether this was a single-packet
transfer or a multi-packet staged transfer.
For single-packet transfers, this had the effect of repeatedly sending
OUT packets with bogus data and lengths.
Eventually if the channel was repeatedly enabled enough times, this
would lock up the OTG core and no further bus transfers would happen.
Set the FSM state up properly if we select a single-packet transfer.
Fixes https://github.com/raspberrypi/linux/issues/1842
dwc_otg: make nak_holdoff work as intended with empty queues
If URBs reading from non-periodic split endpoints were dequeued and
the last transfer from the endpoint was a NAK handshake, the resulting
qh->nak_frame value was stale which would result in unnecessarily long
polling intervals for the first subsequent transfer with a fresh URB.
Fixup qh->nak_frame in dwc_otg_hcd_urb_dequeue and also guard against
a case where a single URB is submitted to the endpoint, a NAK was
received on the transfer immediately prior to receiving data and the
device subsequently resubmits another URB past the qh->nak_frame interval.
Fixes https://github.com/raspberrypi/linux/issues/1709
dwc_otg: fix split transaction data toggle handling around dequeues
See https://github.com/raspberrypi/linux/issues/1709
Fix several issues regarding endpoint state when URBs are dequeued
- If the HCD is disconnected, flush FIQ-enabled channels properly
- Save the data toggle state for bulk endpoints if the last transfer
from an endpoint where URBs were dequeued returned a data packet
- Reset hc->start_pkt_count properly in assign_and_init_hc()
dwc_otg: fix several potential crash sources
On root port disconnect events, the host driver state is cleared and
in-progress host channels are forcibly stopped. This doesn't play
well with the FIQ running in the background, so:
- Guard the disconnect callback with both the host spinlock and FIQ
spinlock
- Move qtd dereference in dwc_otg_handle_hc_fsm() after the early-out
so we don't dereference a qtd that has gone away
- Turn catch-all BUG()s in dwc_otg_handle_hc_fsm() into warnings.
dwc_otg: delete hcd->channel_lock
The lock serves no purpose as it is only held while the HCD spinlock
is already being held.
dwc_otg: remove unnecessary dma-mode channel halts on disconnect interrupt
Host channels are already halted in kill_urbs_in_qh_list() with the
subsequent interrupt processing behaving as if the URB was dequeued
via HCD callback.
There's no need to clobber the host channel registers a second time
as this exposes races between the driver and host channel resulting
in hcd->free_hc_list becoming corrupted.
dwcotg: Allow to build without FIQ on ARM64
Signed-off-by: popcornmix <popcornmix@gmail.com>
dwc_otg: make periodic scheduling behave properly for FS buses
If the root port is in full-speed mode, transfer times at 12mbit/s
would be calculated but matched against high-speed quotas.
Reinitialise hcd->frame_usecs[i] on each port enable event so that
full-speed bandwidth can be tracked sensibly.
Also, don't bother using the FIQ for transfers when in full-speed
mode - at the slower bus speed, interrupt frequency is reduced by
an order of magnitude.
Related issue: https://github.com/raspberrypi/linux/issues/2020
dwc_otg: fiq_fsm: Make isochronous compatibility checks work properly
Get rid of the spammy printk and local pointer mangling.
Also, there is a nominal benefit for using fiq_fsm for isochronous
transfers in FS mode (~1.1k IRQs per second vs 2.1k IRQs per second)
so remove the root port speed check.
dwc_otg: add module parameter int_ep_interval_min
Add a module parameter (defaulting to ignored) that clamps the polling rate
of high-speed Interrupt endpoints to a minimum microframe interval.
The parameter is modifiable at runtime as it is used when activating new
endpoints (such as on device connect).
dwc_otg: fiq_fsm: Add non-periodic TT exclusivity constraints
Certain hub types do not discriminate between pipe direction (IN or OUT)
when considering non-periodic transfers. Therefore these hubs get confused
if multiple transfers are issued in different directions with the same
device address and endpoint number.
Constrain queuing non-periodic split transactions so they are performed
serially in such cases.
Related: https://github.com/raspberrypi/linux/issues/2024
dwc_otg: Fixup change to DRIVER_ATTR interface
dwc_otg: Fix compilation warnings
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
USB_DWCOTG: Disable building dwc_otg as a module (#2265)
When dwc_otg is built as a module, build will fail with the following
error:
ERROR: "DWC_TASK_HI_SCHEDULE" [drivers/usb/host/dwc_otg/dwc_otg.ko] undefined!
scripts/Makefile.modpost:91: recipe for target '__modpost' failed
make[1]: *** [__modpost] Error 1
Makefile:1199: recipe for target 'modules' failed
make: *** [modules] Error 2
Even if the error is solved by including the missing
DWC_TASK_HI_SCHEDULE function, the kernel will panic when loading
dwc_otg.
As a workaround, simply prevent user from building dwc_otg as a module
as the current kernel does not support it.
See: https://github.com/raspberrypi/linux/issues/2258
Signed-off-by: Malik Olivier Boussejra <malik@boussejra.com>
dwc_otg: New timer API
dwc_otg: Fix removed ACCESS_ONCE->READ_ONCE
dwc_otg: don't unconditionally force host mode in dwc_otg_cil_init()
Add the ability to disable force_host_mode for those that want to use
dwc_otg in both device and host modes.
dwc_otg: Fix a regression when dequeueing isochronous transfers
In 282bed95 (dwc_otg: make nak_holdoff work as intended with empty queues)
the dequeue mechanism was changed to leave FIQ-enabled transfers to run
to completion - to avoid leaving hub TT buffers with stale packets lying
around.
This broke FIQ-accelerated isochronous transfers, as this then meant that
dozens of transfers were performed after the dequeue function returned.
Restore the state machine fence for isochronous transfers.
fiq_fsm: rewind DMA pointer for OUT transactions that fail (#2288)
See: https://github.com/raspberrypi/linux/issues/2140
dwc_otg: add smp_mb() to prevent driver state corruption on boot
Occasional crashes have been seen where the FIQ code dereferences
invalid/random pointers immediately after being set up, leading to
panic on boot.
The crash occurs as the FIQ code races against hcd_init_fiq() and
the hcd_init_fiq() code races against the outstanding memory stores
from dwc_otg_hcd_init(). Use explicit barriers after touching
driver state.
usb: dwc_otg: fix memory corruption in dwc_otg driver
[Upstream commit 51b1b64917]
The move from the staging tree to the main tree exposed a
longstanding memory corruption bug in the dwc2 driver. The
reordering of the driver initialization caused the dwc2 driver
to corrupt the initialization data of the sdhci driver on the
Raspberry Pi platform, which made the bug show up.
The error is in calling to_usb_device(hsotg->dev), since ->dev
is not a member of struct usb_device. The easiest fix is to
just remove the offending code, since it is not really needed.
Thanks to Stephen Warren for tracking down the cause of this.
Reported-by: Andre Heider <a.heider@gmail.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[lukas: port from upstream dwc2 to out-of-tree dwc_otg driver]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
usb: dwb_otg: Fix unreachable switch statement warning
This warning appears with GCC 7.3.0 from toolchains.bootlin.com:
../drivers/usb/host/dwc_otg/dwc_otg_fiq_fsm.c: In function ‘fiq_fsm_update_hs_isoc’:
../drivers/usb/host/dwc_otg/dwc_otg_fiq_fsm.c:595:61: warning: statement will never be executed [-Wswitch-unreachable]
st->hctsiz_copy.b.xfersize = nrpackets * st->hcchar_copy.b.mps;
~~~~~~~~~~~~~~~~~^~~~
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
dwc_otg: fiq_fsm: fix incorrect DMA register offset calculation
Rationalise the offset and update all call sites.
Fixes https://github.com/raspberrypi/linux/issues/2408
dwc_otg: fix bug with port_addr assignment for single-TT hubs
See https://github.com/raspberrypi/linux/issues/2734
The "Hub Port" field in the split transaction packet was always set
to 1 for single-TT hubs. The majority of single-TT hub products
apparently ignore this field and broadcast to all downstream enabled
ports, which masked the issue. A subset of hub devices apparently
need the port number to be exact or split transactions will fail.
usb: dwc_otg: Clean up build warnings on 64bit kernels
No functional changes. Almost all are changes to logging lines.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
usb: dwc_otg: Use dma allocation for mphi dummy_send buffer
The FIQ driver used a kzalloc'ed buffer for dummy_send,
passing a kernel virtual address to the hardware block.
The buffer is only ever used for a dummy read, so it
should be harmless, but there is the chance that it will
cause exceptions.
Use a dma allocation so that we have a genuine bus address,
and read from that.
Free the allocation when done for good measure.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
dwc_otg: only do_split when we actually need to do a split
The previous test would fail if the root port was in fullspeed mode
and there was a hub between the FS device and the root port. While
the transfer worked, the schedule mangling performed for high-speed
split transfers would break leading to an 8ms polling interval.
dwc_otg: fix locking around dequeueing and killing URBs
kill_urbs_in_qh_list() is practically only ever called with the fiq lock
already held, so don't spinlock twice in the case where we need to cancel
an isochronous transfer.
Also fix up a case where the global interrupt register could be read with
the fiq lock not held.
Fixes the deadlock seen in https://github.com/raspberrypi/linux/issues/2907
ARM64/DWC_OTG: Port dwc_otg driver to ARM64
In ARM64, the FIQ mechanism used by this driver is not current
implemented. As a workaround, reqular IRQ is used instead
of FIQ.
In a separate change, the IRQ-CPU mapping is round robined
on ARM64 to increase concurrency and allow multiple interrupts
to be serviced at a time. This reduces the need for FIQ.
Tests Run:
This mechanism is most likely to break when multiple USB devices
are attached at the same time. So the system was tested under
stress.
Devices:
1. USB Speakers playing back a FLAC audio through VLC
at 96KHz.(Higher then typically, but supported on my speakers).
2. sftp transferring large files through the buildin ethernet
connection which is connected through USB.
3. Keyboard and mouse attached and being used.
Although I do occasionally hear some glitches, the music seems to
play quite well.
Signed-off-by: Michael Zoran <mzoran@crowfest.net>
usb: dwc_otg: Clean up interrupt claiming code
The FIQ/IRQ interrupt number identification code is scattered through
the dwc_otg driver. Rationalise it, simplifying the code and solving
an existing issue.
See: https://github.com/raspberrypi/linux/issues/2612
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
dwc_otg: Choose appropriate IRQ handover strategy
2711 has no MPHI peripheral, but the ARM Control block can fake
interrupts. Use the size of the DTB "mphi" reg block to determine
which is required.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
usb: host: dwc_otg: fix compiling in separate directory
The dwc_otg Makefile does not respect the O=path argument correctly:
include paths in CFLAGS are given relatively to object path, not source
path. Compiling in a separate directory yields #include errors.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
dwc_otg: use align_buf for small IN control transfers (#3150)
The hardware will do a 4-byte write to memory on any IN packet received
that is between 1 and 3 bytes long. This tramples memory in the uvcvideo
driver, as it uses a sequence of 1- and 2-byte control transfers to
query the min/max/range/step of each individual camera control and
gives us buffers that are offsets into a struct.
Catch small control transfers in the data phase and use the align_buf
to bounce the correct number of bytes into the URB's buffer.
In general, short packets on non-control endpoints should be OK as URBs
should have enough buffer space for a wMaxPacket size transfer.
See: https://github.com/raspberrypi/linux/issues/3148
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
dwc_otg: Declare DMA capability with HCD_DMA flag
Following [1], USB controllers have to declare DMA capabilities in
order for them to be used by adding the HCD_DMA flag to their hc_driver
struct.
[1] 7b81cb6bdd ("usb: add a HCD_DMA flag instead of guestimating DMA capabilities")
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
dwc_otg: checking the urb->transfer_buffer too early (#3332)
After enable the HIGHMEM and VMSPLIT_3G, the dwc_otg driver doesn't
work well on Pi2/3 boards with 1G physical ram. Users experience
the failure when copying a file of 600M size to the USB stick. And
at the same time, the dmesg shows:
usb 1-1.1.2: reset high-speed USB device number 8 using dwc_otg
sd 0:0:0:0: [sda] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
blk_update_request: I/O error, dev sda, sector 3024048 op 0x1:(WRITE) flags 0x4000 phys_seg 15 prio class 0
When this happens, the sg_buf sent to the driver is located in the
highmem region, the usb_sg_init() in the core/message.c will leave
transfer_buffer to NULL if the sg_buf is in highmem, but in the
dwc_otg driver, it returns -EINVAL unconditionally if transfer_buffer
is NULL.
The driver can handle the situation of buffer to be NULL, if it is in
DMA mode, it will convert an address from transfer_dma.
But if the conversion fails or it is in the PIO mode, we should check
buffer and return -EINVAL if it is NULL.
BugLink: https://bugs.launchpad.net/bugs/1852510
Signed-off-by: Hui Wang <hui.wang@canonical.com>
dwc_otg: constrain endpoint max packet and transfer size on split IN
The hcd would unconditionally set the transfer length to the endpoint
packet size for non-isoc IN transfers. If the remaining buffer length
was less than the length of returned data, random memory would get
scribbled over, with bad effects if it crossed a page boundary.
Force a babble error if this happens by limiting the max transfer size
to the available buffer space. DMA will stop writing to memory on a
babble condition.
The hardware expects xfersize to be an integer multiple of maxpacket
size, so override hcchar.b.mps as well.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
dwc_otg: fiq_fsm: pause when cancelling split transactions
Non-periodic splits will DMA to/from the driver-provided transfer_buffer,
which may be freed immediately after the dequeue call returns. Block until
we know the transfer is complete.
A similar delay is needed when cleaning up disconnects, as the FIQ could
have started a periodic transfer in the previous microframe to the one
that triggered a disconnect.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
dwc_otg: fiq_fsm: add a barrier on entry into FIQ handler(s)
On BCM2835, there is no hardware guarantee that multiple outstanding
reads to different peripherals will complete in-order. The FIQ code
uses peripheral reads without barriers for performance, so in the case
where a read to a slow peripheral was issued immediately prior to FIQ
entry, the first peripheral read that the FIQ did could end up with
wrong read data returned.
Add dsb(sy) on entry so that all outstanding reads are retired.
The FIQ only issues reads to the dwc_otg core, so per-read barriers
in the handler itself are not required.
On BCM2836 and BCM2837 the barrier is not strictly required due to
differences in how the peripheral bus is implemented, but having
arch-specific handlers that introduce different latencies is risky.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Signed-off-by: popcornmix <popcornmix@gmail.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2709: Drop platform smp and timer init code
irq-bcm2836 handles this through these functions:
bcm2835_init_local_timer_frequency()
bcm2836_arm_irqchip_smp_init()
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm270x: Use watchdog for reboot/poweroff
The watchdog driver already has support for reboot/poweroff.
Make use of this and remove the code from the platform files.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
board_bcm2835: Remove coherent dma pool increase - API has gone
Under some circumstances on BCM283x processors data loss can be
observed - a single byte missing from the TX output stream. These bytes
are always the last byte of a batch of 8 written from pl011_tx_chars
when from_irq is true, meaning that the FIFO full flag is not checked
before writing.
The transmit optimisation relies on the FIFO being half-empty when the
TX interrupt is raised. Instrumenting the driver further showed that
the failure case correlated with the TX FIFO full flag being set at the
point where the last byte was written to the data register, which
explains the data loss but not how the FIFO appeared to be prematurely
full. A possible explanation is that a FIFO write was in flight at the
time the interrupt was raised, but as yet there is no hypothesis as to
how this might occur.
In the absence of a clear understanding of the failure mechanism, avoid
the problem by checking the FIFO levels before writing the last byte of
the group, which will have minimal performance impact.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The PL011 driver lacks throttle and unthrottle methods. As a result,
sending more data to the Pi than it can immediately sink while CRTSCTS
is enabled causes a NULL pointer to be followed.
Add a throttle handler that disables the RX interrupts, and an
unthrottle handler that reenables them.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
pl011_tx_chars takes a "from_irq" parameter to reduce the number of
register accesses. When from_irq is true the function assumes that the
FIFO is half empty and writes up to half a FIFO's worth of bytes
without polling the FIFO status register, the reasoning being that
the function is being called as a result of the TX interrupt being
raised. This logic would work were it not for the fact that
pl011_rx_chars, called from pl011_int before pl011_tx_chars, releases
the spinlock before calling tty_flip_buffer_push.
A user thread writing to the UART claims the spinlock and ultimately
calls pl011_tx_chars with from_irq set to false. This reverts to the
older logic that polls the FIFO status register before sending every
byte. If this happen on an SMP system during the section of the IRQ
handler where the spinlock has been released, then by the time the TX
interrupt handler is called, the FIFO may already be full, and any
further writes are likely to be lost.
The fix involves adding a per-port flag that is true iff running from
within the interrupt handler and the spinlock has not yet been released.
This flag is then used as the value for the from_irq parameter of
pl011_tx_chars, causing polling to be used in the unsafe case.
Fixes: 1e84d22322 ("serial/amba-pl011: Refactor and simplify TX FIFO handling")
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The BCM2835 PL011 implementation seems to have a bug that can lead to a
transmission lockup if CTS changes frequently. A workaround was added to
the driver with a vendor-specific flag to enable it, but this flag is
currently not set for ARM implementations.
Add a "cts-event-workaround" property to Pi DTBs and use the presence
of that property to force the flag to be enabled in the driver.
See: https://github.com/raspberrypi/linux/issues/1280
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The pl011 register accessor functions use the _relaxed versions of the
standard readl() and writel() functions, meaning that there are no
automatic memory barriers. When polling a FIFO status register to check
for fullness, it is necessary to ensure that any outstanding writes have
completed; otherwise the flags are effectively stale, making it possible
that the next write is to a full FIFO.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The UART clock is initialised to be as close to the requested
frequency as possible without exceeding it. Now that there is a
clock manager that returns the actual frequencies, an expected
48MHz clock is reported as 47999625. If the requested baudrate
== requested clock/16, there is no headroom and the slight
reduction in actual clock rate results in failure.
Detect cases where it looks like a "round" clock was chosen and
adjust the reported clock to match that "round" value. As the
code comment says:
/*
* If increasing a clock by less than 0.1% changes it
* from ..999.. to ..000.., round up.
*/
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The pl011 driver looks for DT aliases of the form "serial<n>",
and if found uses <n> as the device ID. This can cause
/dev/ttyAMA0 to become /dev/ttyAMA1, which is confusing if the
other serial port is provided by the 8250 driver which doesn't
use the same logic.
For applications of the LAN78xx that don't have valid programmed
EEPROMs or OTPs, enabling both LEDs and auto-negotiation by default
seems reasonable.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The syscon node defines a register range that duplicates that used by
the local_intc node on bcm2836/7. Since irq-bcm2835 and irq-bcm2836 are
built in and always present together (both drivers are enabled by
CONFIG_ARCH_BCM2835), it is possible to replace the syscon usage with a
global variable that simplifies the code. Doing so does lose the
locking provided by regmap, but as only one side is using the regmap
interface (irq-bcm2835 uses readl and write) there is no loss of
atomicity.
See: https://github.com/raspberrypi/firmware/issues/926
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
See commit dae803e165 -- the warning is
expected sometimes when using CMA. However, that commit still spams
my kernel log with these warnings.
Signed-off-by: Eric Anholt <eric@anholt.net>
This adds a debug module parameter to aid in debugging transfer issues
by printing info to the kernel log. When enabled, status values are
collected in the interrupt routine and msg info in
bcm2835_i2c_start_transfer(). This is done in a way that tries to avoid
affecting timing. Having printk in the isr can mask issues.
debug values (additive):
1: Print info on error
2: Print info on all transfers
3: Print messages before transfer is started
The value can be changed at runtime:
/sys/module/i2c_bcm2835/parameters/debug
Example output, debug=3:
[ 747.114448] bcm2835_i2c_xfer: msg(1/2) write addr=0x54, len=2 flags= [i2c1]
[ 747.114463] bcm2835_i2c_xfer: msg(2/2) read addr=0x54, len=32 flags= [i2c1]
[ 747.117809] start_transfer: msg(1/2) write addr=0x54, len=2 flags= [i2c1]
[ 747.117825] isr: remain=2, status=0x30000055 : TA TXW TXD TXE [i2c1]
[ 747.117839] start_transfer: msg(2/2) read addr=0x54, len=32 flags= [i2c1]
[ 747.117849] isr: remain=32, status=0xd0000039 : TA RXR TXD RXD [i2c1]
[ 747.117861] isr: remain=20, status=0xd0000039 : TA RXR TXD RXD [i2c1]
[ 747.117870] isr: remain=8, status=0x32 : DONE TXD RXD [i2c1]
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Christopher Alexander Tobias Schulze - May 2, 2015, 11:57 a.m.
This patch fixes a problem with VFP state save and restore related
to exception handling (panic with message "BUG: unsupported FP
instruction in kernel mode") present on VFP11 floating point units
(as used with ARM1176JZF-S CPUs, e.g. on first generation Raspberry
Pi boards). This patch was developed and discussed on
https://github.com/raspberrypi/linux/issues/859
A precondition to see the crashes is that floating point exception
traps are enabled. In this case, the VFP11 might determine that a FPU
operation needs to trap at a point in time when it is not possible to
signal this to the ARM11 core any more. The VFP11 will then set the
FPEXC.EX bit and store the trapped opcode in FPINST. (In some cases,
a second opcode might have been accepted by the VFP11 before the
exception was detected and could be reported to the ARM11 - in this
case, the VFP11 also sets FPEXC.FP2V and stores the second opcode in
FPINST2.)
If FPEXC.EX is set, the VFP11 will "bounce" the next FPU opcode issued
by the ARM11 CPU, which will be seen by the ARM11 as an undefined opcode
trap. The VFP support code examines the FPEXC.EX and FPEXC.FP2V bits
to decide what actions to take, i.e., whether to emulate the opcodes
found in FPINST and FPINST2, and whether to retry the bounced instruction.
If a user space application has left the VFP11 in this "pending trap"
state, the next FPU opcode issued to the VFP11 might actually be the
VSTMIA operation vfp_save_state() uses to store the FPU registers
to memory (in our test cases, when building the signal stack frame).
In this case, the kernel crashes as described above.
This patch fixes the problem by making sure that vfp_save_state() is
always entered with FPEXC.EX cleared. (The current value of FPEXC has
already been saved, so this does not corrupt the context. Clearing
FPEXC.EX has no effects on FPINST or FPINST2. Also note that many
callers already modify FPEXC by setting FPEXC.EN before invoking
vfp_save_state().)
This patch also addresses a second problem related to FPEXC.EX: After
returning from signal handling, the kernel reloads the VFP context
from the user mode stack. However, the current code explicitly clears
both FPEXC.EX and FPEXC.FP2V during reload. As VFP11 requires these
bits to be preserved, this patch disables clearing them for VFP
implementations belonging to architecture 1. There should be no
negative side effects: the user can set both bits by executing FPU
opcodes anyway, and while user code may now place arbitrary values
into FPINST and FPINST2 (e.g., non-VFP ARM opcodes) the VFP support
code knows which instructions can be emulated, and rejects other
opcodes with "unhandled bounce" messages, so there should be no
security impact from allowing reloading FPEXC.EX and FPEXC.FP2V.
Signed-off-by: Christopher Alexander Tobias Schulze <cat.schulze@alice-dsl.net>
At present there is no mechanism to specify driver load order,
which can lead to deferrals and repeated retries until successful.
Since this situation is expected, reduce the dmesg level to
INFO and mention that the operation will be retried.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The VPU is responsible for managing the core clock, usually under
direction from the bcm2835-cpufreq driver but not via the clk-bcm2835
driver. Since the core frequency can change without warning, it is
safer to report the maximum clock rate to users of the core clock -
I2C, SPI and the mini UART - to err on the safe side when calculating
clock divisors.
If the DT node for the clock driver includes a reference to the
firmware node, use the firmware API to query the maximum core clock
instead of reading the divider registers.
Prior to this patch, a "100KHz" I2C bus was sometimes clocked at about
160KHz. In particular, switching to the 4.9 kernel was likely to break
SenseHAT usage on a Pi3.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The claim-clocks property can be used to prevent PLLs and dividers
from being marked as critical. It contains a vector of clock IDs,
as defined by dt-bindings/clock/bcm2835.h.
Use this mechanism to claim PLLD_DSI0, PLLD_DSI1, PLLH_AUX and
PLLH_PIX for the vc4_kms_v3d driver.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The VPU configures and relies on several PLLs and dividers. Mark all
enabled dividers and their PLLs as CRITICAL to prevent the kernel from
switching them off.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The Raspberry Pi firmware looks at the RSTS register to know which
partition to boot from. The reboot syscall command
LINUX_REBOOT_CMD_RESTART2 supports passing in a string argument.
Add support for passing in a partition number 0..63 to boot from.
Partition 63 is a special partiton indicating halt.
If the partition doesn't exist, the firmware falls back to partition 0.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Load driver early since at least bcm2708_fb doesn't support deferred
probing and even if it did, we don't want the video driver deferred.
Support the legacy DMA API which is needed by bcm2708_fb.
Don't mask out channel 2.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
An alternative strategy would be to use "rpi,spidev" instead, but that
would require many Raspberry Pi Device Tree changes.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Add a duplicate irq range with an offset on the hwirq's so the
driver can detect that enable_fiq() is used.
Tested with downstream dwc_otg USB controller driver.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
smsc95xx is adjusting truesize when it shouldn't, and following a recent patch from Eric this is now triggering warnings.
This patch stops smsc95xx from changing truesize.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
This reverts commit c7dacf5b0f.
The Pi 400 shutdown/poweroff mechanism relies on being able to set
a GPIO on the expander in the pm_power_off handler, something that
requires two mailbox calls - GET_GPIO_STATE and SET_GPIO_STATE. A
recent kernel change introduces a reasonable possibility that the
GET call doesn't completes, and bisecting led to a commit from
October that changes the timer usage of the mailbox.
My theory is that there is a race condition in the new code that breaks
the poll timer, but that it normally goes unnoticed because subsequent
mailbox activity wakes it up again. The power-off mailbox calls happen
at a time when other subsystems have been shut down, so if one of them
fails then there is nothing to allow it to recover.
See: https://github.com/raspberrypi/linux/issues/3941
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
This repository contains the Linux kernel used on the Raspberry Pi. If you believe that the issue you are seeing is kernel-related, this is the right place. If not, we have other repositories for the GPU firmware at [github.com/raspberrypi/firmware](https://github.com/raspberrypi/firmware) and Raspberry Pi userland applications at [github.com/raspberrypi/userland](https://github.com/raspberrypi/userland). If you have problems with the Raspbian distribution packages, report them in the [github.com/RPi-Distro/repo](https://github.com/RPi-Distro/repo). If you simply have a question, then [the Raspberry Pi forums](https://www.raspberrypi.org/forums) are the best place to ask it.
**Describe the bug**
Add a clear and concise description of what you think the bug is.
**To reproduce**
List the steps required to reproduce the issue.
**Expected behaviour**
Add a clear and concise description of what you expected to happen.
**Actual behaviour**
Add a clear and concise description of what actually happened.
**System**
Copy and paste the results of the raspinfo command in to this section. Alternatively, copy and paste a pastebin link, or add answers to the following questions:
* Which model of Raspberry Pi? e.g. Pi3B+, PiZeroW
* Which OS and version (`cat /etc/rpi-issue`)?
* Which firmware version (`vcgencmd version`)?
* Which kernel version (`uname -a`)?
**Logs**
If applicable, add the relevant output from `dmesg` or similar.
/* Pi3 uses a GPIO expander to drive the LEDs which can only be accessed
from the VPU. There is a special driver for this with a separate DT node,
which has the unfortunate consequence of breaking the act_led_gpio and
act_led_activelow dtparams.
This overlay changes the GPIO controller back to the standard one and
restores the dtparams.
*/
/{
compatible = "brcm,bcm2835";
fragment@0 {
target = <&act_led>;
frag0: __overlay__ {
gpios = <&gpio 0 0>;
};
};
__overrides__ {
gpio = <&frag0>,"gpios:4";
activelow = <&frag0>,"gpios:8";
};
};
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
