Add a scaler to the ttyS0 clock so that requesting 38400 baud results
in an approximately 31250 baud signal. This is analagous to
midi-uart0, except for ttyS0, which may be useful on Pi3 and also
may avoid an issue with ttyAMA0 failing to synchronise to an active
data stream.
See: https://www.raspberrypi.org/forums/viewtopic.php?f=107&t=183860
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The BCM2835 MINI UART has non-standard THRE semantics. Conventionally
the bit means that the FIFO is empty (although there may still be a
byte in the transmit register), but on 2835 it indicates that the FIFO
is not empty. This causes interrupts after every byte is transmitted,
with the FIFO providing some interrupt latency tolerance.
A consequence of this difference is that the usual strategy of writing
multiple bytes into the TX FIFO after checking THRE once is unsafe.
In the worst case of 7 bytes in the FIFO, writing 8 bytes loses all
but the first since by then the FIFO is full.
There is an HFIFO ("Hidden FIFO") bit which is almost what is needed,
but it only adds more bytes while both THRE and TEMT are set, i.e.
when the TX side is completely idle. This is unnecessarily pessimistic.
Add a new special case, predicated on CAP_MINI, that loops until THRE
is no longer set. With this change, the FIFO fills quickly but
subsequent writes are paced by the transmission rate.
See: https://github.com/raspberrypi/linux/issues/1855
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
commit 7c61b0d5e8 upstream.
Some CH340 devices appear unable to change the initial LCR settings, so
set a sane 8N1 default during probe to enable basic support for such
devices.
Also drop a redundant LCR read during device initialisation.
Signed-off-by: Johan Hovold <johan@kernel.org>
commit d087e7a991 upstream.
The AUX/mini-UART in the BCM2835 family of procesors is a cut-down
8250 clone. In particular it is lacking support for the following
features: CSTOPB PARENB PARODD CMSPAR CS5 CS6
Add a new capability (UART_CAP_MINI) that exposes the restrictions to
the user of the termios API by turning off the unsupported features in
the request.
N.B. It is almost possible to automatically discover the missing
features by reading back the LCR register, but the CSIZE bits don't
cooperate (contrary to the documentation, both bits are significant,
but CS5 and CS6 are mapped to CS7) and the code is much longer.
See: https://github.com/raspberrypi/linux/issues/1561
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the root port is in full-speed mode, transfer times at 12mbit/s
would be calculated but matched against high-speed quotas.
Reinitialise hcd->frame_usecs[i] on each port enable event so that
full-speed bandwidth can be tracked sensibly.
Also, don't bother using the FIQ for transfers when in full-speed
mode - at the slower bus speed, interrupt frequency is reduced by
an order of magnitude.
Related issue: https://github.com/raspberrypi/linux/issues/2020
Fractional clock dividers generate accurate average frequencies but
with jitter, particularly when the integer divisor is small.
Introduce a new metric of clock accuracy to penalise clocks with a good
average but worse jitter compared to clocks with an average which is no
better but with lower jitter. The metric is the ideal rate minus the
worse deviation from that ideal using the nearest integer divisors.
Use this metric for parent selection for clocks requiring low jitter
(currently just PCM).
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The mmc, sdhost, sdio and sdio-1bit overlays had a few
anachronisms and oddities which were overdue for fixing.
The new versions should be functionally equivalent.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
of zero must be changed to 0xffff, however this feature is not
supported by smsc95xx family hence enable csum offload only for
IPv4 TCP/UDP packets.
Signed-off-by: Nisar Sayed <Nisar.Sayed@microchip.com>
Reported-by: popcorn mix <popcornmix@gmail.com>
If firmware has locked up it is useful to get vcdbg log out without a firmware mbox response.
Issue the mbox call at probe time instead.
Signed-off-by: popcornmix <popcornmix@gmail.com>
In fiq_fsm_start_next_periodic() if an isochronous OUT transfer
was selected, no regard was given as to whether this was a single-packet
transfer or a multi-packet staged transfer.
For single-packet transfers, this had the effect of repeatedly sending
OUT packets with bogus data and lengths.
Eventually if the channel was repeatedly enabled enough times, this
would lock up the OTG core and no further bus transfers would happen.
Set the FSM state up properly if we select a single-packet transfer.
Fixes https://github.com/raspberrypi/linux/issues/1842
Currently if two cores access the same page concurrently one will return VM_FAULT_NOPAGE
and the other VM_FAULT_SIGBUS crashing the user code.
Also report when mapping fails.
Signed-off-by: popcornmix <popcornmix@gmail.com>
See https://github.com/raspberrypi/linux/issues/1709
Fix several issues regarding endpoint state when URBs are dequeued
- If the HCD is disconnected, flush FIQ-enabled channels properly
- Save the data toggle state for bulk endpoints if the last transfer
from an endpoint where URBs were dequeued returned a data packet
- Reset hc->start_pkt_count properly in assign_and_init_hc()
If URBs reading from non-periodic split endpoints were dequeued and
the last transfer from the endpoint was a NAK handshake, the resulting
qh->nak_frame value was stale which would result in unnecessarily long
polling intervals for the first subsequent transfer with a fresh URB.
Fixup qh->nak_frame in dwc_otg_hcd_urb_dequeue and also guard against
a case where a single URB is submitted to the endpoint, a NAK was
received on the transfer immediately prior to receiving data and the
device subsequently resubmits another URB past the qh->nak_frame interval.
Fixes https://github.com/raspberrypi/linux/issues/1709
It is unwise to use sources other than the oscillator and PLLD_PER for
the PCM peripheral (and perhaps others - TBD) because their rate can
change and they may even be switched off, so explicitly restrict the
choice using dummy entries in the list of potential parents (item index
is significant).
See: https://github.com/raspberrypi/linux/issues/1949
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The driver was failing to check that the SKB wasn't cloned
before adding checksum data.
Replace existing handling to extend/copy the header buffer
with skb_cow_head.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is an EXAMPLE CODE of Raspberry Pi TV HAT device tree overlay.
Although this is not a part of our release code, it has been used to verify
CXD2880 device driver with TV HAT.
Add the following line to /boot/config.txt to enable TV HAT:
dtoverlay=rpi-tv
Reboot Raspberry Pi and check the existance of /proc/device-tree/soc/spi@7e204000/cxd2880@0.
If exists, the installation is successful. you should be able to find the following three files.
/dev/dvb/adapter0/frontend0
/dev/dvb/adapter0/demux0
/dev/dvb/adapter0/dvr0
Signed-off-by: Yasunari Takiguchi <Yasunari.Takiguchi@sony.com>
Signed-off-by: Masayuki Yamamoto <Masayuki.Yamamoto@sony.com>
Signed-off-by: Hideki Nozawa <Hideki.Nozawa@sony.com>
Signed-off-by: Kota Yonezawa <Kota.Yonezawa@sony.com>
Signed-off-by: Toshihiko Matsumoto <Toshihiko.Matsumoto@sony.com>
Signed-off-by: Satoshi Watanabe <Satoshi.C.Watanabe@sony.com>
This patch adds new sample rates to the Audioinjector Octo sound card. The
new supported rates are (in kHz) :
96, 48, 32, 24, 16, 8, 88.2, 44.1, 29.4, 22.05, 14.7
Reference the bcm270x DT regulators in the overlay.
This patch adds a reset GPIO for the AudioInjector.net octo sound card.
The brightness_set method is intended for use cases that must not
block, and can only be used if the GPIO provider can never sleep.
Remove an accidental initialisation (a copy-and-paste error) that
sets it regardless, which has been seen to cause crashes with the
gpio expander driver.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Upcoming firmware will modify the address portion of node names when
their "reg" property is written by a dtparam. Modify the w1-gpio
overlays to write the gpiopin parameter value to "reg" properties, so
that multiple instances can be loaded simultaneously.
Note: The value of the "address" is unimportant - the w1 subsystem
assigns instance numbers to buses sequentially from 1, and it is
not necessary to know which bus a device is on in order to find it.
Without a prompt string, a config setting can't be included in a
defconfig. Give CONFIG_SND_SOC_ICS43432 a prompt so that Pi soundcards
can use the driver.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The API for port_parameter_get() requires that the
filled length is returned, or if insufficient space
that the required space is returned.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
brcmexp_gpio_set was adding gpio->gc.base to the offset
twice, so passing an invalid number to the mailbox service.
The firmware treated it modulo-8 anyway, but was logging an
assert every time.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Firmware expgpio driver reworked due to complaint over
hotplug detect.
Requires power LED to change sense as firmware is no longer
inverting the read value.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
The upstream dt-bindings documentation for bcm2835-thermal (which
exists even though the driver isn't upstreamed) says to use
dedicated compatible strings on bcm2836 and bcm2837, even though
the downstream driver doesn't support them. The Pi2 DTB uses
"brcm,bcm2836-thermal", so the driver doesn't load. The Pi3 DTB
doesn't override the base value, but the arm64 Pi3 support uses "brcm,bcm2837-thermal".
Solve the documentation problem by adding "brcm,bcm2836-thermal" and
"brcm,bcm2837-thermal" as alternative compatible strings for the
bcm2835-thermal driver.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Commit 488f9bc8e3 slightly increased the
reported rate of PLLD, so the clk driver decided that PLLD/3/8 was now
higher than our requested pixel clock rate and rejected it in favor of
PLLD/4/8, which then ran the pixel clock way out of spec.
By bumping the requested clock rate just slightly, we get back to
PLLD/3/8 like we wanted and the panel displays content again.
Signed-off-by: Eric Anholt <eric@anholt.net>
Commonly used desktop environments such as xfce4 and gnome
on debian sid can flood the graphics drivers with cursor
updates. Because the current implementation is waiting
for a vblank between cursor updates, this will cause the
display to hang for a long time since a typical refresh
rate is only 60Hz.
This is unnecessary and unexpected by user mode software,
so simply swap out the cursor frame buffer without waiting.
Signed-off-by: Michael Zoran <mzoran@crowfest.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
If a CMA allocation failed, the partially constructed BO would be
unreferenced through the normal path, and we might choose to put it in
the BO cache. If we then reused it before it expired from the cache,
the kernel would OOPS.
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes: c826a6e106 ("drm/vc4: Add a BO cache.")
The from_cache flag was actually "the BO is invisible to userspace",
so we can repurpose to just zero out a cached BO and return it to
userspace.
Improves wall time for a loop of 5 glsl-algebraic-add-add-1 by
-1.44989% +/- 0.862891% (n=28, 1 outlier removed from each that
appeared to be other system noise)
Note that there's an intel-gpu-tools test to check for the proper
zeroing behavior here, which we continue to pass.
Signed-off-by: Eric Anholt <eric@anholt.net>
In the rewrite of vc4_crtc.c for fkms, I dropped the part of the
CRTC's atomic flush handler that moved the completion event from the
proposed atomic state change to the CRTC's current state. That meant
that when full screen pageflipping happened (glxgears -fullscreen in
X, compton, por weston), the app would end up blocked firever waiting
to draw its next frame.
Signed-off-by: Eric Anholt <eric@anholt.net>
The DSI0 and DSI1 blocks on the 2835 are related hardware blocks.
Some registers move around, and the featureset is slightly different,
as DSI1 (the 4-lane DSI) is a later version of the hardware block.
This driver doesn't yet enable DSI0, since we don't have any hardware
to test against, but it does put a lot of the register definitions and
code in place.
Signed-off-by: Eric Anholt <eric@anholt.net>
We have to set a different pixel format, which tells the hardware to
use the pix_width field that's fed in sideband from the DSI encoder to
divide the "pixel" clock.
Signed-off-by: Eric Anholt <eric@anholt.net>
We want the HVS on, obviously, and we also want DSP3 (PV1's source) to
be muxed from HVS channel 2 like we expect in vc4_crtc.c. The
firmware wasn't setting the DSP3 mux up when both the LCD and HDMI
were disabled.
Signed-off-by: Eric Anholt <eric@anholt.net>
The modules stay disabled by default, and if you want to enable DSI
you'll need an overlay that connects a panel to it.
Signed-off-by: Eric Anholt <eric@anholt.net>
This driver communicates with the Atmel microcontroller for sequencing
the poweron of the TC358762 DSI-DPI bridge and controlling the
backlight PWM.
The following lines are required in config.txt, to keep the firmware
from trying to bash our I2C lines and steal the DSI interrupts:
disable_touchscreen=1
ignore_lcd=2
mask_gpu_interrupt1=0x1000
This means that the firmware won't power on the panel at boot time (no
rainbow) and the touchscreen input won't work. The native input
driver for the touchscreen still needs to be written.
v2: Set the same default orientation as the closed source firmware
used, which is the best for viewing angle.
Signed-off-by: Eric Anholt <eric@anholt.net>
This proved incredibly useful during debugging of the DSI driver, to
see if our clocks were running at rate we requested. Let's leave it
here for the next person interacting with clocks on the platform (and
so that hopefully we can just hook it up to debugfs some day).
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
(cherry picked from commit 3f9195811d)
The DSI pixel clocks are muxed from clocks generated in the analog phy
by the DSI driver. In order to set them as parents, we need to do the
same name lookup dance on them as we do for our root oscillator.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
(cherry picked from commit 8a39e9fa57)
Our core PLLs are intended to be configured once and left alone. With
the SET_RATE_PARENT, asking to set the PLLD_DSI1 clock rate would
change PLLD just to get closer to the requested DSI clock, thus
changing PLLD_PER, the UART and ethernet PHY clock rates downstream of
it, and breaking ethernet.
We *do* want PLLH to change so that PLLH_AUX can be exactly the value
we want, though. Thus, we need to have a per-divider policy of
whether to pass rate changes up.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
(cherry picked from commit 55486091bd)
These divide off of PLLD_PER and are used for the ethernet and wifi
PHYs source PLLs. Neither of them is currently represented by a phy
device that would grab the clock for us.
This keeps other drivers from killing the networking PHYs when they
disable their own clocks and trigger PLLD_PER's refcount going to 0.
v2: Skip marking as critical if they aren't on at boot.
Signed-off-by: Eric Anholt <eric@anholt.net>
Contrary to the documentation, the BCM2835 GPIO controller actually has
four interrupt lines - one each for the three IRQ groups and one common. Rather
confusingly, the GPIO interrupt groups don't correspond directly with the GPIO
control banks. Instead, GPIOs 0-27 generate IRQ GPIO0, 28-45 GPIO1 and
46-53 GPIO2.
Awkwardly, the GPIOS for IRQ GPIO1 straddle two 32-entry GPIO banks, so it is
cleaner to split out a function to process the interrupts for a single GPIO
bank.
This bug has only just been observed because GPIOs above 27 can only be
accessed on an old Raspberry Pi with the optional P5 header fitted, where
the pins are often used for I2S instead.
https://github.com/raspberrypi/linux/issues/1447
port_parameter_get() failed to account for the header
(u32 id and u32 size) in the size before memcpying
the response into the response buffer, so overrunning
the provided buffer by 8 bytes.
Account for those bytes, and also a belt-and-braces
check to ensure we never copy more than *value_size
bytes into value.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
The VPU is responsible for managing the core clock, usually under
direction from the bcm2835-cpufreq driver but not via the clk-bcm2835
driver. Since the core frequency can change without warning, it is
safer to report the maximum clock rate to users of the core clock -
I2C, SPI and the mini UART - to err on the safe side when calculating
clock divisors.
If the DT node for the clock driver includes a reference to the
firmware node, use the firmware API to query the maximum core clock
instead of reading the divider registers.
Prior to this patch, a "100KHz" I2C bus was sometimes clocked at about
160KHz. In particular, switching to the 4.9 kernel was likely to break
SenseHAT usage on a Pi3.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Add DT support for the Pi Zero W. N.B. It will not be loaded
automatically without a corresponding change to the firmware.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Pi3 and Compute Module 3 have a GPIO expander that the
VPU communicates with.
There is a mailbox service that now allows control of this
expander, so add a kernel driver that can make use of it.
Pwr_led node added to device-tree for Pi3.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
H264 header come off VC with 0 timestamps, which means they get a
strange timestamp when processed with VC/kernel start times,
particularly if used with the inline header option.
Remember the last frame timestamp and use that if set, or otherwise
use the kernel start time.
https://github.com/raspberrypi/linux/issues/1836
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
The UART clock is initialised to be as close to the requested
frequency as possible without exceeding it. Now that there is a
clock manager that returns the actual frequencies, an expected
48MHz clock is reported as 47999625. If the requested baudrate
== requested clock/16, there is no headroom and the slight
reduction in actual clock rate results in failure.
Detect cases where it looks like a "round" clock was chosen and
adjust the reported clock to match that "round" value. As the
code comment says:
/*
* If increasing a clock by less than 0.1% changes it
* from ..999.. to ..000.., round up.
*/
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
If a clock has the prediv flag set, both the integer and fractional
parts must be scaled when calculating the resulting frequency.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Fe-Pi Audio Sound Card is based on NXP SGTL5000 codec.
Mechanical specification of the board is the same the Raspberry Pi Zero.
3.5mm jacks for Headphone/Mic, Line In, and Line Out.
Signed-off-by: Henry Kupis <fe-pi@cox.net>
The code responsible for splitting periods into chunks that
can be handled by the DMA controller missed to update total_len,
the number of bytes processed in the current period, when there
are more chunks to follow.
Therefore total_len was stuck at 0 and the code didn't work at all.
This resulted in a wrong control block layout and audio issues because
the cyclic DMA callback wasn't executing on period boundaries.
Fix this by adding the missing total_len update.
Signed-off-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Tested-by: Clive Messer <clive.messer@digitaldreamtime.co.uk>
Reviewed-by: Eric Anholt <eric@anholt.net>
The claim-clocks property can be used to prevent PLLs and dividers
from being marked as critical. It contains a vector of clock IDs,
as defined by dt-bindings/clock/bcm2835.h.
Use this mechanism to claim PLLD_DSI0, PLLD_DSI1, PLLH_AUX and
PLLH_PIX for the vc4_kms_v3d driver.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The brcmfmac WiFi driver always complains about the '00' country code
and the firmware version is reported as an error. Modify the driver to
ignore '00' silently and display firmware version at INFO level.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
With an ethernet node in the DT, a suitable firmware can populate the
local-mac-address property, removing the need for a downstream patch
to the driver to read its MAC address from a module parameter.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Since driver load deferrals are expected and will already
have resulted in a kernel message, suppress an essentially
duplicate error message from the RPi audio board drivers.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
At present there is no mechanism to specify driver load order,
which can lead to deferrals and repeated retries until successful.
Since this situation is expected, reduce the dmesg level to
INFO and mention that the operation will be retried.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The VPU configures and relies on several PLLs and dividers. Mark all
enabled dividers and their PLLs as CRITICAL to prevent the kernel from
switching them off.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Kernel does not copy input data of ISO transfers to userspace
if actual_length is set only in ISO transfers and not summarized
in urb->actual_length. Fixesraspberrypi/linux#903
Note: due to problems with deferred probing of regulators
the following softdep should be added to a modprobe.d file
softdep arizona-spi pre: arizona-ldo1
Signed-off-by: Matthias Reichl <hias@horus.com>
Reference 3.3V / 5V system rails instead of instantiating local
regulators.
Add missing power supply properties for codecs where these are
required according to the DT bindings docs.
Signed-off-by: Matthias Reichl <hias@horus.com>
Christopher Alexander Tobias Schulze - May 2, 2015, 11:57 a.m.
This patch fixes a problem with VFP state save and restore related
to exception handling (panic with message "BUG: unsupported FP
instruction in kernel mode") present on VFP11 floating point units
(as used with ARM1176JZF-S CPUs, e.g. on first generation Raspberry
Pi boards). This patch was developed and discussed on
https://github.com/raspberrypi/linux/issues/859
A precondition to see the crashes is that floating point exception
traps are enabled. In this case, the VFP11 might determine that a FPU
operation needs to trap at a point in time when it is not possible to
signal this to the ARM11 core any more. The VFP11 will then set the
FPEXC.EX bit and store the trapped opcode in FPINST. (In some cases,
a second opcode might have been accepted by the VFP11 before the
exception was detected and could be reported to the ARM11 - in this
case, the VFP11 also sets FPEXC.FP2V and stores the second opcode in
FPINST2.)
If FPEXC.EX is set, the VFP11 will "bounce" the next FPU opcode issued
by the ARM11 CPU, which will be seen by the ARM11 as an undefined opcode
trap. The VFP support code examines the FPEXC.EX and FPEXC.FP2V bits
to decide what actions to take, i.e., whether to emulate the opcodes
found in FPINST and FPINST2, and whether to retry the bounced instruction.
If a user space application has left the VFP11 in this "pending trap"
state, the next FPU opcode issued to the VFP11 might actually be the
VSTMIA operation vfp_save_state() uses to store the FPU registers
to memory (in our test cases, when building the signal stack frame).
In this case, the kernel crashes as described above.
This patch fixes the problem by making sure that vfp_save_state() is
always entered with FPEXC.EX cleared. (The current value of FPEXC has
already been saved, so this does not corrupt the context. Clearing
FPEXC.EX has no effects on FPINST or FPINST2. Also note that many
callers already modify FPEXC by setting FPEXC.EN before invoking
vfp_save_state().)
This patch also addresses a second problem related to FPEXC.EX: After
returning from signal handling, the kernel reloads the VFP context
from the user mode stack. However, the current code explicitly clears
both FPEXC.EX and FPEXC.FP2V during reload. As VFP11 requires these
bits to be preserved, this patch disables clearing them for VFP
implementations belonging to architecture 1. There should be no
negative side effects: the user can set both bits by executing FPU
opcodes anyway, and while user code may now place arbitrary values
into FPINST and FPINST2 (e.g., non-VFP ARM opcodes) the VFP support
code knows which instructions can be emulated, and rejects other
opcodes with "unhandled bounce" messages, so there should be no
security impact from allowing reloading FPEXC.EX and FPEXC.FP2V.
Signed-off-by: Christopher Alexander Tobias Schulze <cat.schulze@alice-dsl.net>
The CM1 dtb contains an empty audio_pins node, but no reference to it.
Adding the usual pinctrl reference from the audio node enables the
audremap overlay (and others) to easily turn on audio.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The introduction of CM3 makes gadget mode on 2709 a useful option,
so enable the building of the required modules. Note that these
modules are not loaded by default and must be enabled with a DT
overlay.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
If it breaks on anybody, they can use the standard device tree
overlays to switch back to the dwc2 driver.
Signed-off-by: Michael Zoran <mzoran@crowfest.net>
IRQ-CPU mapping is round robined on ARM64 to increase
concurrency and allow multiple interrupts to be serviced
at a time. This reduces the need for FIQ.
Signed-off-by: Michael Zoran <mzoran@crowfest.net>
In ARM64, the FIQ mechanism used by this driver is not current
implemented. As a workaround, reqular IRQ is used instead
of FIQ.
In a separate change, the IRQ-CPU mapping is round robined
on ARM64 to increase concurrency and allow multiple interrupts
to be serviced at a time. This reduces the need for FIQ.
Tests Run:
This mechanism is most likely to break when multiple USB devices
are attached at the same time. So the system was tested under
stress.
Devices:
1. USB Speakers playing back a FLAC audio through VLC
at 96KHz.(Higher then typically, but supported on my speakers).
2. sftp transferring large files through the buildin ethernet
connection which is connected through USB.
3. Keyboard and mouse attached and being used.
Although I do occasionally hear some glitches, the music seems to
play quite well.
Signed-off-by: Michael Zoran <mzoran@crowfest.net>
The spi0-cs overlay allows the software chip selectts to be modified
using the cs0_pin and cs1_pin parameters.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
These drivers build now, so they can be enabled back
in the build configuration just like they are for
32 bit.
Signed-off-by: Michael Zoran <mzoran@crowfest.net>
These drivers use an ASM function from the base
system to compute the ipv6 checksum. These functions
are not available on ARM64, probably because nobody
has bother to write them. The base system does have
a generic "C" version, so a simple fix is to include
the header to use the generic version on ARM64 only.
A longer term solution would be to submit the necessary
ASM function to the upstream source.
With this change, these drivers now compile without
any errors on ARM64.
Signed-off-by: Michael Zoran <mzoran@crowfest.net>
Randomization allows the mapping between virtual addresses and physical
address to be different on each boot. This makes it more difficult
to exploit security vulnerabilities that require knowledge of fixed
hardware addresses.
The firmware generates a 8 byte random number during bootup and stores
it in the device tree under chosen/kaslr-seed. This number is used
to randomize the address mapping.
This change enables this feature in the build configuration for ARM64.
Signed-off-by: Michael Zoran <mzoran@crowfest.net>
In the messages sent to VCHIQ, SND_BCM2835 passes a callback
and a context into two 32 bit pointers. Since this
message is interpreted by the firmware, it can't be easily
changed. Luckily only one of these fields is actual used,
so on ARM64 only use one of the fields to store the upper
half of the 64 bit callback pointer.
The Kconfig is also changed to allow ARM audio to work for ARM64
as well.
Signed-off-by: Michael Zoran <mzoran@crowfest.net>
The function vchiq_copy_from_user contains a non-portable
cast to uint32_t. Convert this to a cast to unsigned long
which is portable.
Signed-off-by: Michael Zoran <mzoran@crowfest.net>
* Invoke the dtc compiler with the same options used in arm mode.
* ARM64 now uses the bcm2835 platform just like ARM32.
* ARM64: Update bcmrpi3_defconfig
Signed-off-by: Michael Zoran <mzoran@crowfest.net>
* Added a writable sysfs object to enable scripts / user space software
to blink MIDI activity LEDs for variable duration.
* Improved hw_param constraints setting.
* Added compatibility with S16_LE sample format.
* Exposed some simple placeholder volume controls, so the card appears
in volumealsa widget.
Signed-off-by: Giedrius Trainavicius <giedrius@blokas.io>
This adds a debug module parameter to aid in debugging transfer issues
by printing info to the kernel log. When enabled, status values are
collected in the interrupt routine and msg info in
bcm2835_i2c_start_transfer(). This is done in a way that tries to avoid
affecting timing. Having printk in the isr can mask issues.
debug values (additive):
1: Print info on error
2: Print info on all transfers
3: Print messages before transfer is started
The value can be changed at runtime:
/sys/module/i2c_bcm2835/parameters/debug
Example output, debug=3:
[ 747.114448] bcm2835_i2c_xfer: msg(1/2) write addr=0x54, len=2 flags= [i2c1]
[ 747.114463] bcm2835_i2c_xfer: msg(2/2) read addr=0x54, len=32 flags= [i2c1]
[ 747.117809] start_transfer: msg(1/2) write addr=0x54, len=2 flags= [i2c1]
[ 747.117825] isr: remain=2, status=0x30000055 : TA TXW TXD TXE [i2c1]
[ 747.117839] start_transfer: msg(2/2) read addr=0x54, len=32 flags= [i2c1]
[ 747.117849] isr: remain=32, status=0xd0000039 : TA RXR TXD RXD [i2c1]
[ 747.117861] isr: remain=20, status=0xd0000039 : TA RXR TXD RXD [i2c1]
[ 747.117870] isr: remain=8, status=0x32 : DONE TXD RXD [i2c1]
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Claiming the completion_mutex within add_completion did prevent some
messages appearing twice, but provokes a deadlock caused by vcsm using
vchiq within a page fault handler.
Revert the use of completion_mutex, and instead fix the original
problem using more memory barriers.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
An issue was observed when flushing openmax components
which generate a large number of messages returning
buffers to host.
We occasionally found a duplicate message from 16
messages prior, resulting in a buffer returned twice.
While only one thread adds completions, without the
mutex you don't get the protection of the automatic
memory barrier you get with synchronisation objects.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Service callbacks are not allowed to return an error. The internal callback
that delivers events and messages to user tasks does not enqueue them if
the service is closing, but this is not an error and should not be
reported as such.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Reading through this code looking for another problem (now found in userland)
the use of dequeue_pending outside a lock didn't seem safe.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Disable MMC_BCM2835_SDHOST and MMC_BCM2835 since these drivers are crashing at the moment.
ARM64: Modify default config to get raspbian to boot (#1686)
1. Enable emulation of deprecated instructions.
2. Enable ARM 8.1 and 8.2 features which are not detected at runtime.
3. Switch the default governer to powersave.
4. Include the watchdog timer driver in the kernel image rather then a module.
Tested with raspbian-jessie 2016-09-23.
brcmfmac: Disable power management
Disable wireless power saving in the brcmfmac WLAN driver. This is a
temporary measure until the connectivity loss resulting from power
saving is resolved.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
brcmfmac: Use original country code as a fallback
Commit 73345fd212:
brcmfmac: Configure country code using device specific settings
prevents region codes from working on devices that lack a region code
translation table. In the event of an absent table, preserve the old
behaviour of using the provided code as-is.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
brcmfmac: Plug memory leak in brcmf_fill_bss_param
See: https://github.com/raspberrypi/linux/issues/1471
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
brcmfmac: do not use internal roaming engine by default
Some evidence of curing disconnects with this disabled, so make it a default.
Can be overridden with module parameter roamoff=0
See: http://projectable.me/optimize-my-pi-wi-fi/
brcmfmac: Change stop_ap sequence
Patch from Broadcom/Cypress to resolve a customer error
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
This is a port of Pantelis Antoniou's v3 port that makes use of the
new upstreamed configfs support for binary attributes.
Original commit message:
Add a runtime interface to using configfs for generic device tree overlay
usage. With it its possible to use device tree overlays without having
to use a per-platform overlay manager.
Please see Documentation/devicetree/configfs-overlays.txt for more info.
Changes since v2:
- Removed ifdef CONFIG_OF_OVERLAY (since for now it's required)
- Created a documentation entry
- Slight rewording in Kconfig
Changes since v1:
- of_resolve() -> of_resolve_phandles().
Originally-signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
DT configfs: Fix build errors on other platforms
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
DT configfs: fix build error
There is an error when compiling rpi-4.6.y branch:
CC drivers/of/configfs.o
drivers/of/configfs.c:291:21: error: initialization from incompatible pointer type [-Werror=incompatible-pointer-types]
.default_groups = of_cfs_def_groups,
^
drivers/of/configfs.c:291:21: note: (near initialization for 'of_cfs_subsys.su_group.default_groups.next')
The .default_groups is linked list since commit
1ae1602de0.
This commit uses configfs_add_default_group to fix this problem.
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
suppress spurious messages
Add #if for 3.14 kernel change (#87)
Fixes compiling after changes in f663dd9aaf and 99932d4fc0Fixes#86
Set dev_type to wlan
Fixes#23
Tentatively added support for more 8188CUS based devices.
Add support for more 8188CUS and 8192CUS devices
Add ProductId for the Netgear N150 - WNA1000M
Fixes CONFIG_CONCURRENT_MODE CONFIG_MULTI_VIR_IFACES
Fixes compatibility with 3.13
Enables warning in the compiler and fixes some issues, reference => https://github.com/diederikdehaas/rtl8812AU
Starts device in station mode instead of monitor, fixes NetworkManager issues
Enable cfg80211 support
Fix cfg80211 for kernel >= 4.7
Fixes rtl8192cu for kernel >= 4.8
Add non-mainline source for rtl8192cu wireless driver version v4.0.2_9000 as
this is widely used. Disable older rtlwifi driver.
8192cu needs old wireless extensions
The obsolete WIRELESS_EXT configuration is used
by the old Realtek code and is needed for AP support.
8192cu: CONFIG_AP_MODE hardcoded in autoconf.h
rtl8192c_rf6052: PHY_RFShadowRefresh(): fix off-by-one
Signed-off-by: Marc Kleine-Budde <mkl@blackshift.org>
rtl8192cu: Add PID for D-Link DWA 131
The pl011 driver looks for DT aliases of the form "serial<n>",
and if found uses <n> as the device ID. This can cause
/dev/ttyAMA0 to become /dev/ttyAMA1, which is confusing if the
other serial port is provided by the 8250 driver which doesn't
use the same logic.
Add a mailbox-driven backlight controller for the Raspberry Pi DSI
touchscreen display. Requires updated GPU firmware to recognise the
mailbox request.
Signed-off-by: Gordon Hollingworth <gordon@raspberrypi.org>
Pisound dynamic overlay (#1760)
Restructuring pisound-overlay.dts, so it can be loaded and unloaded dynamically using dtoverlay.
Print a logline when the kernel module is removed.
Add initial 2 channel (stereo) support for Allo Piano DAC (2.0/2.1) boards,
using allo-piano-dac-pcm512x-audio overlay and allo-piano-dac ALSA ASoC
machine driver.
NB. The initial support is 2 channel (stereo) ONLY!
(The Piano DAC 2.1 will only support 2 channel (stereo) left/right output,
pending an update to the upstream pcm512x codec driver, which will have
to be submitted via upstream. With the initial downstream support,
provided by this patch, the Piano DAC 2.1 subwoofer outputs will
not function.)
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net>
Signed-off-by: Clive Messer <clive.messer@digitaldreamtime.co.uk>
Tested-by: Clive Messer <clive.messer@digitaldreamtime.co.uk>
Support IQAudIO Digi board with iqaudio_digi machine driver and
iqaudio-digi-wm8804-audio overlay.
NB. Machine driver is a cut and paste of hifiberry_digi code, with format
and general cleanup to comply with kernel coding standards.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
Contains the sound/soc/bcm ALSA machine driver and necessary alterations to the Kconfig and Makefile.
Adds the dts overlay and updates the Makefile and README.
Updates the relevant defconfig files to enable building for the Raspberry Pi.
Thanks to Phil Elwell (pelwell) for the review, simple-card concepts and discussion. Thanks to Clive Messer for overlay naming suggestions.
Added support for headphones, microphone and bclk_ratio settings.
This patch adds headphone and microphone capability to the Audio Injector sound card. The patch also sets the bit clock ratio for use in the bcm2835-i2s driver. The bcm2835-i2s can't handle an 8 kHz sample rate when the bit clock is at 12 MHz because its register is only 10 bits wide which can't represent the ch2 offset of 1508. For that reason, the rate constraint is added.
This commit adds basic support for the codec usage including: Device tree overlay,
binding I2S bus and setting I2S mode, clock source and frequency setting according
to spec.
Signed-off-by: Andrey Grodzovsky <andrey2805@gmail.com>
justboom-dac: Adjust for ALSA API change
As of 4.4, snd_soc_limit_volume now takes a struct snd_soc_card *
rather than a struct snd_soc_codec *.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Jan Grulich <jan@grulich.eu>
config: fix RaspiDAC Rev.3x dependencies
Change depends to SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S
like the other I2S soundcard drivers.
Signed-off-by: Matthias Reichl <hias@horus.com>
The driver contains a low-level hardware driver for the TAS5713 and the
drivers for the Raspberry Pi I2S subsystem.
TAS5713: return error if initialisation fails
Existing TAS5713 driver logs errors during initialisation, but does not return
an error code. Therefore even if initialisation fails, the driver will still be
loaded, but won't work. This patch fixes this. I2C communication error will now
reported correctly by a non-zero return code.
HiFiBerry Amp: fix device-tree problems
Some code to load the driver based on device-tree-overlays was missing. This is added by this patch.
The driver is based on the HiFiBerry DAC driver. However HiFiBerry DAC+ uses
a different codec chip (PCM5122), therefore a new driver is necessary.
Add support for the HiFiBerry DAC+ Pro.
The HiFiBerry DAC+ and DAC+ Pro products both use the existing bcm sound driver with the DAC+ Pro having a special clock device driver representing the two high precision oscillators.
An addition bug fix is included for the PCM512x codec where by the physical size of the sample frame is used in the calculation of the LRCK divisor as it was found to be wrong when using 24-bit depth sample contained in a little endian 4-byte sample frame.
Limit PCM512x "Digital" gain to 0dB by default with HiFiBerry DAC+
24db_digital_gain DT param can be used to specify that PCM512x
codec "Digital" volume control should not be limited to 0dB gain,
and if specified will allow the full 24dB gain.
Add dt param to force HiFiBerry DAC+ Pro into slave mode
"dtoverlay=hifiberry-dacplus,slave"
Add 'slave' param to use HiFiBerry DAC+ Pro in slave mode,
with Pi as master for bit and frame clock.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
Set a limit of 0dB on Digital Volume Control
The main volume control in the PCM512x DAC has a range up to
+24dB. This is dangerously loud and can potentially cause massive
clipping in the output stages. Therefore this sets a sensible
limit of 0dB for this control.
Allow up to 24dB digital gain to be applied when using IQAudIO DAC+
24db_digital_gain DT param can be used to specify that PCM512x
codec "Digital" volume control should not be limited to 0dB gain,
and if specified will allow the full 24dB gain.
Modify IQAudIO DAC+ ASoC driver to set card/dai config from dt
Add the ability to set the card name, dai name and dai stream name, from
dt config.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
IQaudIO: auto-mute for AMP+ and DigiAMP+
IQAudIO amplifier mute via GPIO22. Add dt params for "one-shot" unmute
and auto mute.
Revision 2, auto mute implementing HiassofT suggestion to mute/unmute
using set_bias_level, rather than startup/shutdown....
"By default DAPM waits 5 seconds (pmdown_time) before shutting down
playback streams so a close/stop immediately followed by open/start
doesn't trigger an amp mute+unmute."
Tested on both AMP+ (via DAC+) and DigiAMP+, with both options...
dtoverlay=iqaudio-dacplus,unmute_amp
"one-shot" unmute when kernel module loads.
dtoverlay=iqaudio-dacplus,auto_mute_amp
Unmute amp when ALSA device opened by a client. Mute, with 5 second delay
when ALSA device closed. (Re-opening the device within the 5 second close
window, will cancel mute.)
Revision 4, using gpiod.
Revision 5, clean-up formatting before adding mute code.
- Convert tab plus 4 space formatting to 2x tab
- Remove '// NOT USED' commented code
Revision 6, don't attempt to "one-shot" unmute amp, unless card is
successfully registered.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
Signed-off-by: Daniel Matuschek <daniel@matuschek.net>
Add a parameter to turn off SPDIF output if no audio is playing
This patch adds the paramater auto_shutdown_output to the kernel module.
Default behaviour of the module is the same, but when auto_shutdown_output
is set to 1, the SPDIF oputput will shutdown if no stream is playing.
bugfix for 32kHz sample rate, was missing
HiFiBerry Digi: set SPDIF status bits for sample rate
The HiFiBerry Digi driver did not signal the sample rate in the SPDIF status bits.
While this is optional, some DACs and receivers do not accept this signal. This patch
adds the sample rate bits in the SPDIF status block.
Added HiFiBerry Digi+ Pro driver
Signed-off-by: Daniel Matuschek <daniel@hifiberry.com>
This adds a machine driver for the HifiBerry DAC.
It is a sound card that can
be stacked onto the Raspberry Pi.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
The Raspberry Pi firmware manages the power-down and reboot
process. To do this it installs a pm_power_off handler, causing
the gpio-poweroff module to abort the probe function.
This patch introduces a "force" DT property that overrides that
behaviour, and also adds a DT overlay to enable and control it.
Note that running in an active-low configuration (DT parameter
"active_low") requires a custom dt-blob.bin and probably won't
allow a reboot without switching off, so an external inversion
of the trigger signal may be preferable.
Provide a __copy_from_user that uses memcpy. On BCM2708, use
optimised memcpy/memmove/memcmp/memset implementations.
arch/arm: Add mmiocpy/set aliases for memcpy/set
See: https://github.com/raspberrypi/linux/issues/1082
copy_from_user: CPU_SW_DOMAIN_PAN compatibility
The downstream copy_from_user acceleration must also play nice with
CONFIG_CPU_SW_DOMAIN_PAN.
See: https://github.com/raspberrypi/linux/issues/1381
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Fix driver detection failure Check that the buffer response is non-zero meaning the touchscreen was detected
rpi-ft5406: Use firmware API
RPI-FT5406: Enable aarch64 support through explicit iomem interface
Signed-off-by: Gerhard de Clercq <gerharddeclercq@outlook.com>
1-wire: Add support for configuring pin for w1-gpio kernel module
See: https://github.com/raspberrypi/linux/pull/457
Add bitbanging pullups, use them for w1-gpio
Allows parasite power to work, uses module option pullup=1
bcm2708: Ensure 1-wire pullup is disabled by default, and expose as module parameter
Signed-off-by: Alex J Lennon <ajlennon@dynamicdevices.co.uk>
w1-gpio: Add gpiopin module parameter and correctly free up gpio pull-up pin, if set
Signed-off-by: Alex J Lennon <ajlennon@dynamicdevices.co.uk>
w1-gpio: Sort out the pullup/parasitic power tangle
Especially on platforms with a slower CPU but a relatively high
framebuffer fill bandwidth, like current ARM devices, the existing
console monochrome imageblit function used to draw console text is
suboptimal for common pixel depths such as 16bpp and 32bpp. The existing
code is quite general and can deal with several pixel depths. By creating
special case functions for 16bpp and 32bpp, by far the most common pixel
formats used on modern systems, a significant speed-up is attained
which can be readily felt on ARM-based devices like the Raspberry Pi
and the Allwinner platform, but should help any platform using the
fb layer.
The special case functions allow constant folding, eliminating a number
of instructions including divide operations, and allow the use of an
unrolled loop, eliminating instructions with a variable shift size,
reducing source memory access instructions, and eliminating excessive
branching. These unrolled loops also allow much better code optimization
by the C compiler. The code that selects which optimized variant is used
is also simplified, eliminating integer divide instructions.
The speed-up, measured by timing 'cat file.txt' in the console, varies
between 40% and 70%, when testing on the Raspberry Pi and Allwinner
ARM-based platforms, depending on font size and the pixel depth, with
the greater benefit for 32bpp.
Signed-off-by: Harm Hanemaaijer <fgenfb@yahoo.com>
Based on the patch authored by Ali Gholami Rudi at
https://lkml.org/lkml/2009/7/13/153
Provide an ioctl for userspace applications, but only if this operation
is hardware accelerated (otherwide it does not make any sense).
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
bcm2708_fb: Add ioctl for reading gpu memory through dma
The "input" trigger makes the associated GPIO an input. This is to support
the Raspberry Pi PWR LED, which is driven by external hardware in normal use.
N.B. pwr_led is not available on Model A or B boards.
leds-gpio: Implement the brightness_get method
The power LED uses some clever logic that means it is driven
by a voltage measuring circuit when configured as input, otherwise
it is driven by the GPIO output value. This patch wires up the
brightness_get method for leds-gpio so that user-space can monitor
the LED value via /sys/class/gpio/led1/brightness. Using the input
trigger this returns an indication of the system power health,
otherwise it is just whatever value the trigger has written most
recently.
See: https://github.com/raspberrypi/linux/issues/1064
Add the bare minimum needed to boot BCM2708 from a Device Tree.
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
BCM2708: DT: change 'axi' nodename to 'soc'
Change DT node named 'axi' to 'soc' so it matches ARCH_BCM2835.
The VC4 bootloader fills in certain properties in the 'axi' subtree,
but since this is part of an upstreaming effort, the name is changed.
Signed-off-by: Noralf Tronnes notro@tronnes.org
BCM2708_DT: Correct length of the peripheral space
Use dts-dirs feature for overlays.
The kernel makefiles have a dts-dirs target that is for vendor subdirectories.
Using this fixes the install_dtbs target, which previously did not install the overlays.
BCM270X_DT: configure I2S DMA channels
Signed-off-by: Matthias Reichl <hias@horus.com>
BCM270X_DT: switch to bcm2835-i2s
I2S soundcard drivers with proper devicetree support (i.e. not linking
to the cpu_dai/platform via name but to cpu/platform via of_node)
will work out of the box without any modifications.
When the kernel is compiled without devicetree support the platform
code will instantiate the bcm2708-i2s driver and I2S soundcard drivers
will link to it via name, as before.
Signed-off-by: Matthias Reichl <hias@horus.com>
SDIO-overlay: add poll_once-boolean parameter
Add paramter to toggle sdio-device-polling
done every second or once at boot-time.
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
BCM270X_DT: Make mmc overlay compatible with current firmware
The original DT overlay logic followed a merge-then-patch procedure,
i.e. parameters are applied to the loaded overlay before the overlay
is merged into the base DTB. This sequence has been changed to
patch-then-merge, in order to support parameterised node names, and
to protect against bad overlays. As a result, overrides (parameters)
must only target labels in the overlay, but the overlay can obviously target nodes in the base DTB.
mmc-overlay.dts (that switches back to the original mmc sdcard
driver) is the only overlay violating that rule, and this patch
fixes it.
bcm270x_dt: Use the sdhost MMC controller by default
The "mmc" overlay reverts to using the other controller.
squash: Add cprman to dt
BCM270X_DT: Use clk_core for I2C interfaces
BCM270X_DT: Use bcm283x.dtsi, bcm2835.dtsi and bcm2836.dtsi
The mainline Device Tree files are quite close to downstream now.
Let's use bcm283x.dtsi, bcm2835.dtsi and bcm2836.dtsi as base files
for our dts files.
Mainline dts files are based on these files:
bcm2835-rpi.dtsi
bcm2835.dtsi bcm2836.dtsi
bcm283x.dtsi
Current downstream are based on these:
bcm2708.dtsi bcm2709.dtsi bcm2710.dtsi
bcm2708_common.dtsi
This patch introduces this dependency:
bcm2708.dtsi bcm2709.dtsi
bcm2708-rpi.dtsi
bcm270x.dtsi
bcm2835.dtsi bcm2836.dtsi
bcm283x.dtsi
And:
bcm2710.dtsi
bcm2708-rpi.dtsi
bcm270x.dtsi
bcm283x.dtsi
bcm270x.dtsi contains the downstream bcm283x.dtsi diff.
bcm2708-rpi.dtsi is the downstream version of bcm2835-rpi.dtsi.
Other changes:
- The led node has moved from /soc/leds to /leds. This is not a problem
since the label is used to reference it.
- The clk_osc reg property changes from 6 to 3.
- The gpu nodes has their interrupt property set in the base file.
- the clocks label does not point to the /clocks node anymore, but
points to the cprman node. This is not a problem since the overlays
that use the clock node refer to it directly: target-path = "/clocks";
- some nodes now have 2 labels since mainline and downstream differs in
this respect: cprman/clocks, spi0/spi, gpu/vc4.
- some nodes doesn't have an explicit status = "okay" since they're not
disabled in the base file: watchdog and random.
- gpiomem doesn't need an explicit status = "okay".
- bcm2708-rpi-cm.dts got the hpd-gpios property from bcm2708_common.dtsi,
it's now set directly in that file.
- bcm2709-rpi-2-b.dts has the timer node moved from /soc/timer to /timer.
- Removed clock-frequency property on the bcm{2709,2710}.dtsi timer nodes.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270X_DT: Use raspberrypi-power to turn on USB power
Use the raspberrypi-power driver to turn on USB power.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270X_DT: Add a .dtbo target, use for overlays
Change the filenames and extensions to keep the pre-DDT style of
overlay (<name>-overlay.dtb) distinct from new ones that use a
different style of local fixups (<name>.dtbo), and to match other
platforms.
The RPi firmware uses the DDTK trailer atom to choose which type of
overlay to use for each kernel.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: Don't generate "linux,phandle" props
The EPAPR standard says to use "phandle" properties to store phandles,
rather than the deprecated "linux,phandle" version. By default, dtc
generates both, but adding "-H epapr" causes it to only generate
"phandle"s, saving some space and clutter.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: Add overlay for enc28j60 on SPI2
Works on SPI2 for compute module
BCM270X_DT: Add midi-uart0 overlay
MIDI requires 31.25kbaud, a baudrate unsupported by Linux. The
midi-uart0 overlay configures uart0 (ttyAMA0) to use a fake clock
so that requesting 38.4kbaud actually gets 31.25kbaud.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: Add i2c-sensor overlay
The i2c-sensor overlay is a container for various pressure and
temperature sensors, currently bmp085 and bmp280. The standalone
bmp085_i2c-sensor overlay is now deprecated.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: overlays/*-overlay.dtb -> overlays/*.dtbo (#1752)
We now create overlays as .dtbo files.
build: support for .dtbo files for dtb overlays
Kernel 4.4.6+ on RaspberryPi support .dtbo files for overlays, instead of .dtb.
Patch the kernel, which has faulty rules to generate .dtbo the way yocto does
Signed-off-by: Herve Jourdain <herve.jourdain@neuf.fr>
Signed-off-by: Khem Raj <raj.khem@gmail.com>
Includes the new localfixups format.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
scripts/dtc: Fix UMR causing corrupt dtbo overlay files
struct fixup_entry is allocated from the heap but it's member
local_fixup_generated was never initialized. This lead to
corrupted dtbo files.
Fix this by initializing local_fixup_generated to false.
Signed-off-by: Matthias Reichl <hias@horus.com>
scripts/dtc: Only emit local fixups for overlays
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The Raspberry Pi firmware looks for a trailer on the kernel image to
determine whether it was compiled with Device Tree support enabled.
If the firmware finds a kernel without this trailer, or which has a
trailer indicating that it isn't DT-capable, it disables DT support
and reverts to using ATAGs.
The mkknlimg utility adds that trailer, having first analysed the
image to look for signs of DT support and the kernel version string.
knlinfo displays the contents of the trailer in the given kernel image.
scripts/mkknlimg: Add support for ARCH_BCM2835
Add a new trailer field indicating whether this is an ARCH_BCM2835
build, as opposed to MACH_BCM2708/9. If the loader finds this flag
is set it changes the default base dtb file name from bcm270x...
to bcm283y...
Also update knlinfo to show the status of the field.
scripts/mkknlimg: Improve ARCH_BCM2835 detection
The board support code contains sufficient strings to be able to
distinguish 2708 vs. 2835 builds, so remove the check for
bcm2835-pm-wdt which could exist in either.
Also, since the canned configuration is no longer built in (it's
a module), remove the config string checking.
See: https://github.com/raspberrypi/linux/issues/1157
scripts: Multi-platform support for mkknlimg and knlinfo
The firmware uses tags in the kernel trailer to choose which dtb file
to load. Current firmware loads bcm2835-*.dtb if the '283x' tag is true,
otherwise it loads bcm270*.dtb. This scheme breaks if an image supports
multiple platforms.
This patch adds '270X' and '283X' tags to indicate support for RPi and
upstream platforms, respectively. '283x' (note lower case 'x') is left
for old firmware, and is only set if the image only supports upstream
builds.
scripts/mkknlimg: Append a trailer for all input
Now that the firmware assumes an unsigned kernel is DT-capable, it is
helpful to be able to mark a kernel as being non-DT-capable.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
scripts/knlinfo: Decode DDTK atom
Show the DDTK atom as being a boolean.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
mkknlimg: Retain downstream-kernel detection
With the death of ARCH_BCM2708 and ARCH_BCM2709, a new way is needed to
determine if this is a "downstream" build that wants the firmware to
load a bcm27xx .dtb. The vc_cma driver is used downstream but not
upstream, making vc_cma_init a suitable predicate symbol.
- Supports raw YUV capture, preview, JPEG and H264.
- Uses videobuf2 for data transfer, using dma_buf.
- Uses 3.6.10 timestamping
- Camera power based on use
- Uses immutable input mode on video encoder
Signed-off-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Luke Diamand <luked@broadcom.com>
V4L2: Fixes from 6by9
V4L2: Fix EV values. Add manual shutter speed control
V4L2 EV values should be in units of 1/1000. Corrected.
Add support for V4L2_CID_EXPOSURE_ABSOLUTE which should
give manual shutter control. Requires manual exposure mode
to be selected first.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Correct JPEG Q-factor range
Should be 1-100, not 0-100
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Fix issue of driver jamming if STREAMON failed.
Fix issue where the driver was left in a partially enabled
state if STREAMON failed, and would then reject many IOCTLs
as it thought it was streaming.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Fix ISO controls.
Driver was passing the index to the GPU, and not the desired
ISO value.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Add flicker avoidance controls
Add support for V4L2_CID_POWER_LINE_FREQUENCY to set flicker
avoidance frequencies.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Add support for frame rate control.
Add support for frame rate (or time per frame as V4L2
inverts it) control via s_parm.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Improve G_FBUF handling so we pass conformance
Return some sane numbers for get framebuffer so that
we pass conformance.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Fix information advertised through g_vidfmt
Width and height were being stored based on incorrect
values.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Add support for inline H264 headers
Add support for V4L2_CID_MPEG_VIDEO_REPEAT_SEQ_HEADER
to control H264 inline headers.
Requires firmware fix to work correctly, otherwise format
has to be set to H264 before this parameter is set.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Fix JPEG timestamp issue
JPEG images were coming through from the GPU with timestamp
of 0. Detect this and give current system time instead
of some invalid value.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Fix issue when switching down JPEG resolution.
JPEG buffer size calculation is based on input resolution.
Input resolution was being configured after output port
format. Caused failures if switching from one JPEG resolution
to a smaller one.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Enable MJPEG encoding
Requires GPU firmware update to support MJPEG encoder.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Correct flag settings for compressed formats
Set flags field correctly on enum_fmt_vid_cap for compressed
image formats.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: H264 profile & level ctrls, FPS control and auto exp pri
Several control handling updates.
H264 profile and level controls.
Timeperframe/FPS reworked to add V4L2_CID_EXPOSURE_AUTO_PRIORITY to
select whether AE is allowed to override the framerate specified.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Correct BGR24 to RGB24 in format table
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Add additional pixel formats. Correct colourspace
Adds the other flavours of YUYV, and NV12.
Corrects the overlay advertised colourspace.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Drop logging msg from info to debug
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Initial pass at scene modes.
Only supports exposure mode and metering modes.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Add manual white balance control.
Adds support for V4L2_CID_RED_BALANCE and
V4L2_CID_BLUE_BALANCE. Only has an effect if
V4L2_CID_AUTO_N_PRESET_WHITE_BALANCE has
V4L2_WHITE_BALANCE_MANUAL selected.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
config: Enable V4L / MMAL driver
V4L2: Increase the MMAL timeout to 3sec
MJPEG codec flush is now taking longer and results
in a kernel panic if the driver has stopped waiting for
the result when it finally completes.
Increase the timeout value from 1 to 3secs.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Add support for setting H264_I_PERIOD
Adds support for the parameter V4L2_CID_MPEG_VIDEO_H264_I_PERIOD
to set the frequency with which I frames are produced.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Enable GPU function for removing padding from images.
GPU can now support arbitrary strides, although may require
additional processing to achieve it. Enable this feature
so that the images delivered are the size requested.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Add support for V4L2_PIX_FMT_BGR32
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Set the colourspace to avoid odd YUV-RGB conversions
Removes the amiguity from the conversion routines and stops
them dropping back to the SD vs HD choice of coeffs.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Make video/still threshold a run-time param
Move the define for at what resolution the driver
switches from a video mode capture to a stills mode
capture to module parameters.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Fix incorrect pool sizing
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Add option to disable enum_framesizes.
Gstreamer's handling of a driver that advertises
V4L2_FRMSIZE_TYPE_STEPWISE to define the supported
resolutions is broken. See bug
https://bugzilla.gnome.org/show_bug.cgi?id=726521
Optional parameter of gst_v4l2src_is_broken added.
If non-zero, the driver claims not to support that
ioctl, and gstreamer should be happy again (it
guesses a set of defaults for itself).
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Add support for more image formats
Adds YVU420 (YV12), YVU420SP (NV21), and BGR888.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Extend range for V4L2_CID_MPEG_VIDEO_H264_I_PERIOD
Request to extend the range from the fairly arbitrary
1000 frames (33 seconds at 30fps). Extend out to the
max range supported (int32 value).
Also allow 0, which is handled by the codec as only
send an I-frame on the first frame and never again.
There may be an exception if it detects a significant
scene change, but there's no easy way around that.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
bcm2835-camera: stop_streaming now has a void return
BCM2835-V4L2: Fix compliance test failures
VIDIOC_TRY_FMT and VIDIOC_S_FMT tests were faling due
to reporting V4L2_COLORSPACE_JPEG when the colour
format wasn't V4L2_PIX_FMT_JPEG.
Now reports V4L2_COLORSPACE_SMPTE170M for YUV formats.
bcm2835 camera planar/packed stride length
Added a field to the mmal_fmt struct used to compute the bytes per line
when using a particular format. This results in the correct stride being
calculated even when the format is planar.
Signed-off-by: Garrett Wilson <g@floft.net>
bcm2835: camera: check for scene not being found
static analysis by cppcheck detected some potential NULL pointer
dereference issues:
[drivers/media/platform/bcm2835/controls.c:854]: (error) Possible null
pointer dereference: scene
(and lines 858, 859 too)
it is possible that scene is not found because of an invalue ctrl->val
and is therefore NULL and hence causing a null pointer dereference.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
bcm2835: memcpy port data to m rather than rmsg
static analysis by cppcheck detected a memcpy to rmsg which is
not actually initialized at that point. The memcpy should be copying
to variable m instead.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
BCM2835-V4L2: Return buffers to videobuf2 on shutdown
https://github.com/raspberrypi/linux/issues/817
Fixes the kernel warning from videobuf2 as buffers
are now returned as they are being flushed on
stop_streaming.
squash: Fixup bcm2835-camera for changes in kernel 4.4 api
v4l2: Fix up driver to upstream timestamp changes
bcm2835-camera: fix a bug in computation of frame timestamp
Fixes#1318
V4L2 driver updates (#1393)
* BCM2835-V4L2: Correct ISO control and add V4L2_CID_ISO_SENSITIVITY_AUTO
https://github.com/raspberrypi/linux/issues/1251
V4L2_CID_ISO_SENSITIVITY was not advertising ISO*1000 as it should.
V4L2_CID_ISO_SENSITIVITY_AUTO was not implemented, so was taking
V4L2_CID_ISO_SENSITIVITY as 0 for auto mode.
Still accepts 0 for auto, but also abides by the new parameter.
Signed-off-by: Dave Stevenson <6by9@users.noreply.github.com>
* BCM2835-V4L2: Add a video_nr parameter.
Adds a kernel parameter "video_nr" to specify the preferred
/dev/videoX device node.
https://www.raspberrypi.org/forums/viewtopic.php?f=38&t=136120&p=905545
Signed-off-by: Dave Stevenson <6by9@users.noreply.github.com>
* BCM2835-V4L2: Add support for multiple cameras
Ask GPU on load how many cameras have been detected, and
enumerate that number of devices.
Only applicable on the Compute Module as no other device
exposes multiple CSI2 interfaces.
Signed-off-by: Dave Stevenson <6by9@users.noreply.github.com>
* BCM2835-V4L2: Add control of the overlay location and alpha.
Actually do something useful in vidioc_s_fmt_vid_overlay and
vidioc_try_fmt_vid_overlay, rather than effectively having
read-only fields.
Signed-off-by: Dave Stevenson <6by9@users.noreply.github.com>
* BCM2835-V4L2: V4L2-Compliance failure fix
VIDIOC_TRY_FMT was failing due to bytesperline not
being set correctly by default.
Signed-off-by: Dave Stevenson <6by9@users.noreply.github.com>
* BCM2835-V4L2: Make all module parameters static
Clean up to correct variable scope
Signed-off-by: Dave Stevenson <6by9@users.noreply.github.com>
V4L2: Request maximum resolution from GPU
Get resolution information about the sensors from the GPU
and advertise it correctly.
Signed-off-by: Dave Stevenson <6by9@users.noreply.github.com>
BCM2835-V4L2: Increase minimum resolution to 32x32
https://github.com/raspberrypi/linux/issues/1498 showed
up that 16x16 is failing to work on the GPU for some reason.
GPU bug being tracked on
https://github.com/raspberrypi/firmware/issues/607
Workaround here by increasing minimum resolution via V4L2
to 32x32.
Signed-off-by: Dave Stevenson <6by9@users.noreply.github.com>
[media]: bcm2835-camera: fix compilation error
There is an error when compiling rpi-4.6.y branch:
CC [M] drivers/media/platform/bcm2835/bcm2835-camera.o
drivers/media/platform/bcm2835/bcm2835-camera.c:639:17: error: initialization from incompatible pointer type [-Werror=incompatible-pointer-types]
.queue_setup = queue_setup,
^
drivers/media/platform/bcm2835/bcm2835-camera.c:639:17: note: (near initialization for 'bm2835_mmal_video_qops.queue_setup')
The const void *parg in setup_queue callback is not needed since commit:
df9ecb0cad.
This commit removes it.
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
bcm2835-camera: Fix max/min error when looping over cameras/resolutions
See: https://github.com/raspberrypi/linux/issues/1447#issuecomment-221303506
BCM2835-V4L2: Correct handling for BGR24 vs RGB24.
There was a bug in the GPU firmware that had reversed these
two formats.
Detect the old firmware, and reverse the formats if necessary.
Signed-off-by: Dave Stevenson <6by9@users.noreply.github.com>
BCM2835-v4l2: Fix a conformance test failure
Format ioctls:
test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK
warn: v4l2-test-formats.cpp(1195): S_PARM is supported but
doesn't report V4L2_CAP_TIMEPERFRAME.
fail: v4l2-test-formats.cpp(1118): node->has_frmintervals
&& !cap->capability
Support booting without Device Tree.
Turn on USB power.
Load driver early because of lacking support for deferred probing
in many drivers.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
firmware: bcm2835: Don't turn on USB power
The raspberrypi-power driver is now used to turn on USB power.
This partly reverts commit:
firmware: bcm2835: Support ARCH_BCM270x
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Add module for accessing the mailbox property channel through
/dev/vcio. Was previously in bcm2708-vcio.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
i2c-bcm2708: fixed baudrate
Fixed issue where the wrong CDIV value was set for baudrates below 3815 Hz (for 250MHz bus clock).
In that case the computed CDIV value was more than 0xffff. However the CDIV register width is only 16 bits.
This resulted in incorrect setting of CDIV and higher baudrate than intended.
Example: 3500Hz -> CDIV=0x11704 -> CDIV(16bit)=0x1704 -> 42430Hz
After correction: 3500Hz -> CDIV=0x11704 -> CDIV(16bit)=0xffff -> 3815Hz
The correct baudrate is shown in the log after the cdiv > 0xffff correction.
Perform I2C combined transactions when possible
Perform I2C combined transactions whenever possible, within the
restrictions of the Broadcomm Serial Controller.
Disable DONE interrupt during TA poll
Prevent interrupt from being triggered if poll is missed and transfer
starts and finishes.
i2c: Make combined transactions optional and disabled by default
i2c: bcm2708: add device tree support
Add DT support to driver and add to .dtsi file.
Setup pins in .dts file.
i2c is disabled by default.
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
bcm2708: don't register i2c controllers when using DT
The devices for the i2c controllers are in the Device Tree.
Only register devices when not using DT.
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
I2C: Only register the I2C device for the current board revision
i2c_bcm2708: Fix clock reference counting
Fix grabbing lock from atomic context in i2c driver
2 main changes:
- check for timeouts in the bcm2708_bsc_setup function as indicated by this comment:
/* poll for transfer start bit (should only take 1-20 polls) */
This implies that the setup function can now fail so account for this everywhere it's called
- Removed the clk_get_rate call from inside the setup function as it locks a mutex and that's not ok since we call it from under a spin lock.
i2c-bcm2708: When using DT, leave the GPIO setup to pinctrl
i2c-bcm2708: Increase timeouts to allow larger transfers
Use the timeout value provided by the I2C_TIMEOUT ioctl when waiting
for completion. The default timeout is 1 second.
See: https://github.com/raspberrypi/linux/issues/260
i2c-bcm2708/BCM270X_DT: Add support for I2C2
The third I2C bus (I2C2) is normally reserved for HDMI use. Careless
use of this bus can break an attached display - use with caution.
It is recommended to disable accesses by VideoCore by setting
hdmi_ignore_edid=1 or hdmi_edid_file=1 in config.txt.
The interface is disabled by default - enable using the
i2c2_iknowwhatimdoing DT parameter.
bcm2708-spi: Don't use static pin configuration with DT
Also remove superfluous error checking - the SPI framework ensures the
validity of the chip_select value.
i2c-bcm2708: Remove non-DT support
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Set the BSC_CLKT clock streching timeout to 35ms as per SMBus specs.
Fixes i2c_bcm2708: Write to FIFO correctly - v2 (#1574)
* i2c: fix i2c_bcm2708: Clear FIFO before sending data
Make sure FIFO gets cleared before trying to send
data in case of a repeated start (COMBINED=Y).
* i2c: fix i2c_bcm2708: Only write to FIFO when not full
Check if FIFO can accept data before writing.
To avoid a peripheral read on the last iteration of a loop,
both bcm2708_bsc_fifo_fill and ~drain are changed as well.
BCM270x: Move thermal sensor to Device Tree
Add Device Tree support to bcm2835-thermal driver.
Add thermal sensor device to Device Tree.
Don't add platform device when booting in DT mode.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
lirc_rpi: Use read_current_timer to determine transmitter delay. Thanks to jjmz and others
See: https://github.com/raspberrypi/linux/issues/525
lirc: Remove restriction on gpio pins that can be used with lirc
Compute Module, for example could use different pins
lirc_rpi: Add parameter to specify input pin pull
Depending on the connected IR circuitry it might be desirable to change the
gpios internal pull from it pull-down default behaviour. Add a module
parameter to allow the user to set it explicitly.
Signed-off-by: Julian Scheel <julian@jusst.de>
lirc-rpi: Use the higher-level irq control functions
This module used to access the irq_chip methods of the
gpio controller directly, rather than going through the
standard enable_irq/irq_set_irq_type functions. This
caused problems on pinctrl-bcm2835 which only implements
the irq_enable/disable methods and not irq_unmask/mask.
lirc-rpi: Correct the interrupt usage
1) Correct the use of enable_irq (i.e. don't call it so often)
2) Correct the shutdown sequence.
3) Avoid a bcm2708_gpio driver quirk by setting the irq flags earlier
lirc-rpi: use getnstimeofday instead of read_current_timer
read_current_timer isn't guaranteed to return values in
microseconds, and indeed it doesn't on a Pi2.
Issue: linux#827
lirc-rpi: Add device tree support, and a suitable overlay
The overlay supports DT parameters that match the old module
parameters, except that gpio_in_pull should be set using the
strings "up", "down" or "off".
lirc-rpi: Also support pinctrl-bcm2835 in non-DT mode
fix auto-sense in lirc_rpi driver
On a Raspberry Pi 2, the lirc_rpi driver might receive spurious
interrupts and change it's low-active / high-active setting.
When this happens, the IR remote control stops working.
This patch disables this auto-detection if the 'sense' parameter
was set in the device tree, making the driver robust to such
spurious interrupts.
Use clock manager instead of self-made clockmanager.
Also fix some error paths that showd up during development
(especially missing release of dma resources on rmmod)
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Add experimental support for the VideoCore shared memory service.
This allows user processes to allocate memory from VideoCore's
GPU relocatable heap and mmap the buffers. Additionally, the memory
handles can passed to other VideoCore services such as MMAL, OpenMax
and DispmanX
TODO
* This driver was originally released for BCM28155 which has a different
cache architecture to BCM2835. Consequently, in this release only
uncached mappings are supported. However, there's no fundamental
reason which cached mappings cannot be support or BCM2835
* More refactoring is required to remove the typedefs.
* Re-enable the some of the commented out debug-fs statistics which were
disabled when migrating code from proc-fs.
* There's a lot of code to support sharing of VCSM in order to support
Android. This could probably done more cleanly or perhaps just
removed.
Signed-off-by: Tim Gover <timgover@gmail.com>
config: Disable VC_SM for now to fix hang with cutdown kernel
vcsm: Use boolean as it cannot be built as module
On building the bcm_vc_sm as a module we get the following error:
v7_dma_flush_range and do_munmap are undefined in vc-sm.ko.
Fix by making it not an option to build as module
vcsm: Add ioctl for custom cache flushing
vc-sm: Move headers out of arch directory
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: popcornmix <popcornmix@gmail.com>
BCM270x: Move vc_mem
Make the vc_mem module available for ARCH_BCM2835 by moving it.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: popcornmix <popcornmix@gmail.com>
alsa: add mmap support and some cleanups to bcm2835 ALSA driver
snd-bcm2835: Add support for spdif/hdmi passthrough
This adds a dedicated subdevice which can be used for passthrough of non-audio
formats (ie encoded a52) through the hdmi audio link. In addition to this
driver extension an appropriate card config is required to make alsa-lib
support the AES parameters for this device.
snd-bcm2708: Add mutex, improve logging
Fix for ALSA driver crash
Avoids an issue when closing and opening vchiq where a message can arrive before service handle has been written
alsa: reduce severity of expected warning message
snd-bcm2708: Fix dmesg spam for non-error case
alsa: Ensure mutexes are released through error paths
alsa: Make interrupted close paths quieter
BCM270x: Add onboard sound device to Device Tree
Add Device Tree support to alsa driver.
Add device to Device Tree.
Don't add platform devices when booting in DT mode.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2835: access controls under the audio mutex
I don't think the ALSA framework provides any kind of automatic
synchronization within the control callbacks. We most likely need
to ensure this manually, so add locking around all access to shared
mutable data. In particular, bcm2835_audio_set_ctls() should
probably always be called under our own audio lock.
snd-bcm2835: Don't allow responses from VC to be interrupted by user signals
There should always be a response, and retry after a signal interruption is not handled, so don't report
we are interruptible.
See: https://github.com/raspberrypi/linux/issues/1560
snd-bcm2835: Use bcm2835_hw params in preallocate
Signed-off-by: popcornmix <popcornmix@gmail.com>
vc_cma: Make the vc_cma area the default contiguous DMA area
vc_cma: Provide empty functions when module is not built
Providing empty functions saves the users from guarding the
function call with an #if clause.
Move __init markings from prototypes to functions.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Some SD cards have been found that corrupt data when small blocks
are erased. Add a quirk to indicate that ERASE should not be used,
and set it for cards of that type.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
mmc: Apply QUIRK_BROKEN_ERASE to other capacities
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
mmc: Add card_quirks module parameter, log quirks
Use mmc_block.card_quirks to override the quirks for all SD or MMC
cards. The value is a bitfield using the bit positions defined in
include/linux/mmc/card.h. If the module parameter is placed in the
kernel command line (or bootargs) stored on the card then, assuming the
device only has one SD card interface, the override effectively becomes
card-specific.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM2835 has two SD card interfaces. This driver uses the other one.
bcm2835-sdhost: Error handling fix, and code clarification
bcm2835-sdhost: Adding overclocking option
Allow a different clock speed to be substitued for a requested 50MHz.
This option is exposed using the "overclock_50" DT parameter.
Note that the sdhost interface is restricted to integer divisions of
core_freq, and the highest sensible option for a core_freq of 250MHz
is 84 (250/3 = 83.3MHz), the next being 125 (250/2) which is much too
high.
Use at your own risk.
bcm2835-sdhost: Round up the overclock, so 62 works for 62.5Mhz
Also only warn once for each overclock setting.
bcm2835-sdhost: Improve error handling and recovery
1) Expose the hw_reset method to the MMC framework, removing many
internal calls by the driver.
2) Reduce overclock setting on error.
3) Increase timeout to cope with high capacity cards.
4) Add properties and parameters to control pio_limit and debug.
5) Reduce messages at probe time.
bcm2835-sdhost: Further improve overclock back-off
bcm2835-sdhost: Clear HBLC for PIO mode
Also update pio_limit default in overlay README.
bcm2835-sdhost: Add the ERASE capability
See: https://github.com/raspberrypi/linux/issues/1076
bcm2835-sdhost: Ignore CRC7 for MMC CMD1
It seems that the sdhost interface returns CRC7 errors for CMD1,
which is the MMC-specific SEND_OP_COND. Returning these errors to
the MMC layer causes a downward spiral, but ignoring them seems
to be harmless.
bcm2835-mmc/sdhost: Remove ARCH_BCM2835 differences
The bcm2835-mmc driver (and -sdhost driver that copied from it)
contains code to handle SDIO interrupts in a threaded interrupt
handler rather than waking the MMC framework thread. The change
follows a patch from Russell King that adds the facility as the
preferred way of working.
However, the new code path is only present in ARCH_BCM2835
builds, which I have taken to be a way of testing the waters
rather than making the change across the board; I can't see
any technical reason why it wouldn't be enabled for MACH_BCM270X
builds. So this patch standardises on the ARCH_BCM2835 code,
removing the old code paths.
bcm2835-sdhost: Don't log timeout errors unless debug=1
The MMC card-discovery process generates timeouts. This is
expected behaviour, so reporting it to the user serves no purpose.
Suppress the reporting of timeout errors unless the debug flag
is on.
bcm2835-sdhost: Add workaround for odd behaviour on some cards
For reasons not understood, the sdhost driver fails when reading
sectors very near the end of some SD cards. The problem could
be related to the similar issue that reading the final sector
of any card as part of a multiple read never completes, and the
workaround is an extension of the mechanism introduced to solve
that problem which ensures those sectors are always read singly.
bcm2835-sdhost: Major revision
This is a significant revision of the bcm2835-sdhost driver. It
improves on the original in a number of ways:
1) Through the use of CMD23 for reads it appears to avoid problems
reading some sectors on certain high speed cards.
2) Better atomicity to prevent crashes.
3) Higher performance.
4) Activity logging included, for easier diagnosis in the event
of a problem.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Restore ATOMIC flag to PIO sg mapping
Allocation problems have been seen in a wireless driver, and
this is the only change which might have been responsible.
SQUASH: bcm2835-sdhost: Only claim one DMA channel
With both MMC controllers enabled there are few DMA channels left. The
bcm2835-sdhost driver only uses DMA in one direction at a time, so it
doesn't need to claim two channels.
See: https://github.com/raspberrypi/linux/issues/1327
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Workaround for "slow" sectors
Some cards have been seen to cause timeouts after certain sectors are
read. This workaround enforces a minimum delay between the stop after
reading one of those sectors and a subsequent data command.
Using CMD23 (SET_BLOCK_COUNT) avoids this problem, so good cards will
not be penalised by this workaround.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Firmware manages the clock divisor
The bcm2835-sdhost driver hands control of the CDIV clock divisor
register to matching firmware, allowing it to adjust to a changing
core clock. This removes the need to use the performance governor or
to enable io_is_busy on the on-demand governor in order to get the
best SD performance.
N.B. As SD clocks must be an integer divisor of the core clock, it is
possible that the SD clock for "turbo" mode can be different (even
lower) than "normal" mode.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Reset the clock in task context
Since reprogramming the clock can now involve a round-trip to the
firmware it must not be done at atomic context, and a tasklet
is not a task.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Don't exit cmd wait loop on error
The FAIL flag can be set in the CMD register before command processing
is complete, leading to spurious "failed to complete" errors. This has
the effect of promoting harmless CRC7 errors during CMD1 processing
into errors that can delay and even prevent booting.
Also:
1) Convert the last KERN_ERROR message in the register dumping to
KERN_INFO.
2) Remove an unnecessary reset call from bcm2835_sdhost_add_host.
See: https://github.com/raspberrypi/linux/pull/1492
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
mmc: Disable CMD23 transfers on all cards
Pending wire-level investigation of these types of transfers
and associated errors on bcm2835-mmc, disable for now. Fallback of
CMD18/CMD25 transfers will be used automatically by the MMC layer.
Reported/Tested-by: Gellert Weisz <gellert@raspberrypi.org>
mmc: bcm2835-mmc: enable DT support for all architectures
Both ARCH_BCM2835 and ARCH_BCM270x are built with OF now.
Enable Device Tree support for all architectures.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
mmc: bcm2835-mmc: fix probe error handling
Probe error handling is broken in several places.
Simplify error handling by using device managed functions.
Replace pr_{err,info} with dev_{err,info}.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2835-mmc: Add locks when accessing sdhost registers
bcm2835-mmc: Add range of debug options for slowing things down
bcm2835-mmc: Add option to disable some delays
bcm2835-mmc: Add option to disable MMC_QUIRK_BLK_NO_CMD23
bcm2835-mmc: Default to disabling MMC_QUIRK_BLK_NO_CMD23
bcm2835-mmc: Adding overclocking option
Allow a different clock speed to be substitued for a requested 50MHz.
This option is exposed using the "overclock_50" DT parameter.
Note that the mmc interface is restricted to EVEN integer divisions of
250MHz, and the highest sensible option is 63 (250/4 = 62.5), the
next being 125 (250/2) which is much too high.
Use at your own risk.
bcm2835-mmc: Round up the overclock, so 62 works for 62.5Mhz
Also only warn once for each overclock setting.
mmc: bcm2835-mmc: Make available on ARCH_BCM2835
Make the bcm2835-mmc driver available for use on ARCH_BCM2835.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270x_DT: add bcm2835-mmc entry
Add Device Tree entry for bcm2835-mmc.
In non-DT mode, don't add the device in the board file.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2835-mmc: Don't overwrite MMC capabilities from DT
bcm2835-mmc: Don't override bus width capabilities from devicetree
Take out the force setting of the MMC_CAP_4_BIT_DATA host capability
so that the result read from devicetree via mmc_of_parse() is
preserved.
bcm2835-mmc: Only claim one DMA channel
With both MMC controllers enabled there are few DMA channels left. The
bcm2835-mmc driver only uses DMA in one direction at a time, so it
doesn't need to claim two channels.
See: https://github.com/raspberrypi/linux/issues/1327
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Add support for DMA controller of BCM2708 as used in the Raspberry Pi.
Currently it only supports cyclic DMA.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
dmaengine: expand functionality by supporting scatter/gather transfers sdhci-bcm2708 and dma.c: fix for LITE channels
DMA: fix cyclic LITE length overflow bug
dmaengine: bcm2708: Remove chancnt affectations
Mirror bcm2835-dma.c commit 9eba5536a7:
chancnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: overwrite dreq only if it is not set
dreq is set when the DMA channel is fetched from Device Tree.
slave_id is set using dmaengine_slave_config().
Only overwrite dreq with slave_id if it is not set.
dreq/slave_id in the cyclic DMA case is not touched, because I don't
have hardware to test with.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: do device registration in the board file
Don't register the device in the driver. Do it in the board file.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: don't restrict DT support to ARCH_BCM2835
Both ARCH_BCM2835 and ARCH_BCM270x are built with OF now.
Add Device Tree support to the non ARCH_BCM2835 case.
Use the same driver name regardless of architecture.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270x_DT: add bcm2835-dma entry
Add Device Tree entry for bcm2835-dma.
The entry doesn't contain any resources since they are handled
by the arch/arm/mach-bcm270x/dma.c driver.
In non-DT mode, don't add the device in the board file.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2708-dmaengine: Add debug options
BCM270x: Add memory and irq resources to dmaengine device and DT
Prepare for merging of the legacy DMA API arch driver dma.c
with bcm2708-dmaengine by adding memory and irq resources both
to platform file device and Device Tree node.
Don't use BCM_DMAMAN_DRIVER_NAME so we don't have to include mach/dma.h
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: Merge with arch dma.c driver and disable dma.c
Merge the legacy DMA API driver with bcm2708-dmaengine.
This is done so we can use bcm2708_fb on ARCH_BCM2835 (mailbox
driver is also needed).
Changes to the dma.c code:
- Use BIT() macro.
- Cutdown some comments to one line.
- Add mutex to vc_dmaman and use this, since the dev lock is locked
during probing of the engine part.
- Add global g_dmaman variable since drvdata is used by the engine part.
- Restructure for readability:
vc_dmaman_chan_alloc()
vc_dmaman_chan_free()
bcm_dma_chan_free()
- Restructure bcm_dma_chan_alloc() to simplify error handling.
- Use device irq resources instead of hardcoded bcm_dma_irqs table.
- Remove dev_dmaman_register() and code it directly.
- Remove dev_dmaman_deregister() and code it directly.
- Simplify bcm_dmaman_probe() using devm_* functions.
- Get dmachans from DT if available.
- Keep 'dma.dmachans' module argument name for backwards compatibility.
Make it available on ARCH_BCM2835 as well.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: set residue_granularity field
bcm2708-dmaengine supports residue reporting at burst level
but didn't report this via the residue_granularity field.
Without this field set properly we get playback issues with I2S cards.
dmaengine: bcm2708-dmaengine: Fix memory leak when stopping a running transfer
bcm2708-dmaengine: Use more DMA channels (but not 12)
1) Only the bcm2708_fb drivers uses the legacy DMA API, and
it requires a BULK-capable channel, so all other types
(FAST, NORMAL and LITE) can be made available to the regular
DMA API.
2) DMA channels 11-14 share an interrupt. The driver can't
handle this, so don't use channels 12-14 (12 was used, probably
because it appears to have an interrupt, but in reality that
interrupt is for activity on ANY channel). This may explain
a lockup encountered when running out of DMA channels.
The combined effect of this patch is to leave 7 DMA channels
available + channel 0 for bcm2708_fb via the legacy API.
See: https://github.com/raspberrypi/linux/issues/1110https://github.com/raspberrypi/linux/issues/1108
dmaengine: bcm2708: Make legacy API available for bcm2835-dma
bcm2708_fb uses the legacy DMA API, so in order to start using
bcm2835-dma, bcm2835-dma has to support the legacy API. Make this
possible by exporting bcm_dmaman_probe() and bcm_dmaman_remove().
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: Change DT compatible string
Both bcm2835-dma and bcm2708-dmaengine have the same compatible string.
So change compatible to "brcm,bcm2708-dma".
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: Remove driver but keep legacy API
Dropping non-DT support means we don't need this driver,
but we still need the legacy DMA API.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2708-dmaengine - Fix arm64 portability/build issues
Signed-off-by: popcornmix <popcornmix@gmail.com>
bcm2708_fb : Implement blanking support using the mailbox property interface
bcm2708_fb: Add pan and vsync controls
bcm2708_fb: DMA acceleration for fb_copyarea
Based on http://www.raspberrypi.org/phpBB3/viewtopic.php?p=62425#p62425
Also used Simon's dmaer_master module as a reference for tweaking DMA
settings for better performance.
For now busylooping only. IRQ support might be added later.
With non-overclocked Raspberry Pi, the performance is ~360 MB/s
for simple copy or ~260 MB/s for two-pass copy (used when dragging
windows to the right).
In the case of using DMA channel 0, the performance improves
to ~440 MB/s.
For comparison, VFP optimized CPU copy can only do ~114 MB/s in
the same conditions (hindered by reading uncached source buffer).
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
bcm2708_fb: report number of dma copies
Add a counter (exported via debugfs) reporting the
number of dma copies that the framebuffer driver
has done, in order to help evaluate different
optimization strategies.
Signed-off-by: Luke Diamand <luked@broadcom.com>
bcm2708_fb: use IRQ for DMA copies
The copyarea ioctl() uses DMA to speed things along. This
was busy-waiting for completion. This change supports using
an interrupt instead for larger transfers. For small
transfers, busy-waiting is still likely to be faster.
Signed-off-by: Luke Diamand <luke@diamand.org>
bcm2708: Make ioctl logging quieter
video: fbdev: bcm2708_fb: Don't panic on error
No need to panic the kernel if the video driver fails.
Just print a message and return an error.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
fbdev: bcm2708_fb: Add ARCH_BCM2835 support
Add Device Tree support.
Pass the device to dma_alloc_coherent() in order to get the
correct bus address on ARCH_BCM2835.
Use the new DMA legacy API header file.
Including <mach/platform.h> is not necessary.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270x_DT: Add bcm2708-fb device
Add bcm2708-fb to Device Tree and don't add the
platform device when booting in DT mode.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: popcornmix <popcornmix@gmail.com>
usb: dwc: fix lockdep false positive
Signed-off-by: Kari Suvanto <karis79@gmail.com>
usb: dwc: fix inconsistent lock state
Signed-off-by: Kari Suvanto <karis79@gmail.com>
Add FIQ patch to dwc_otg driver. Enable with dwc_otg.fiq_fix_enable=1. Should give about 10% more ARM performance.
Thanks to Gordon and Costas
Avoid dynamic memory allocation for channel lock in USB driver. Thanks ddv2005.
Add NAK holdoff scheme. Enabled by default, disable with dwc_otg.nak_holdoff_enable=0. Thanks gsh
Make sure we wait for the reset to finish
dwc_otg: fix bug in dwc_otg_hcd.c resulting in silent kernel
memory corruption, escalating to OOPS under high USB load.
dwc_otg: Fix unsafe access of QTD during URB enqueue
In dwc_otg_hcd_urb_enqueue during qtd creation, it was possible that the
transaction could complete almost immediately after the qtd was assigned
to a host channel during URB enqueue, which meant the qtd pointer was no
longer valid having been completed and removed. Usually, this resulted in
an OOPS during URB submission. By predetermining whether transactions
need to be queued or not, this unsafe pointer access is avoided.
This bug was only evident on the Pi model A where a device was attached
that had no periodic endpoints (e.g. USB pendrive or some wlan devices).
dwc_otg: Fix incorrect URB allocation error handling
If the memory allocation for a dwc_otg_urb failed, the kernel would OOPS
because for some reason a member of the *unallocated* struct was set to
zero. Error handling changed to fail correctly.
dwc_otg: fix potential use-after-free case in interrupt handler
If a transaction had previously aborted, certain interrupts are
enabled to track error counts and reset where necessary. On IN
endpoints the host generates an ACK interrupt near-simultaneously
with completion of transfer. In the case where this transfer had
previously had an error, this results in a use-after-free on
the QTD memory space with a 1-byte length being overwritten to
0x00.
dwc_otg: add handling of SPLIT transaction data toggle errors
Previously a data toggle error on packets from a USB1.1 device behind
a TT would result in the Pi locking up as the driver never handled
the associated interrupt. Patch adds basic retry mechanism and
interrupt acknowledgement to cater for either a chance toggle error or
for devices that have a broken initial toggle state (FT8U232/FT232BM).
dwc_otg: implement tasklet for returning URBs to usbcore hcd layer
The dwc_otg driver interrupt handler for transfer completion will spend
a very long time with interrupts disabled when a URB is completed -
this is because usb_hcd_giveback_urb is called from within the handler
which for a USB device driver with complicated processing (e.g. webcam)
will take an exorbitant amount of time to complete. This results in
missed completion interrupts for other USB packets which lead to them
being dropped due to microframe overruns.
This patch splits returning the URB to the usb hcd layer into a
high-priority tasklet. This will have most benefit for isochronous IN
transfers but will also have incidental benefit where multiple periodic
devices are active at once.
dwc_otg: fix NAK holdoff and allow on split transactions only
This corrects a bug where if a single active non-periodic endpoint
had at least one transaction in its qh, on frnum == MAX_FRNUM the qh
would get skipped and never get queued again. This would result in
a silent device until error detection (automatic or otherwise) would
either reset the device or flush and requeue the URBs.
Additionally the NAK holdoff was enabled for all transactions - this
would potentially stall a HS endpoint for 1ms if a previous error state
enabled this interrupt and the next response was a NAK. Fix so that
only split transactions get held off.
dwc_otg: Call usb_hcd_unlink_urb_from_ep with lock held in completion handler
usb_hcd_unlink_urb_from_ep must be called with the HCD lock held. Calling it
asynchronously in the tasklet was not safe (regression in
c4564d4a1a).
This change unlinks it from the endpoint prior to queueing it for handling in
the tasklet, and also adds a check to ensure the urb is OK to be unlinked
before doing so.
NULL pointer dereference kernel oopses had been observed in usb_hcd_giveback_urb
when a USB device was unplugged/replugged during data transfer. This effect
was reproduced using automated USB port power control, hundreds of replug
events were performed during active transfers to confirm that the problem was
eliminated.
USB fix using a FIQ to implement split transactions
This commit adds a FIQ implementaion that schedules
the split transactions using a FIQ so we don't get
held off by the interrupt latency of Linux
dwc_otg: fix device attributes and avoid kernel warnings on boot
dcw_otg: avoid logging function that can cause panics
See: https://github.com/raspberrypi/firmware/issues/21
Thanks to cleverca22 for fix
dwc_otg: mask correct interrupts after transaction error recovery
The dwc_otg driver will unmask certain interrupts on a transaction
that previously halted in the error state in order to reset the
QTD error count. The various fine-grained interrupt handlers do not
consider that other interrupts besides themselves were unmasked.
By disabling the two other interrupts only ever enabled in DMA mode
for this purpose, we can avoid unnecessary function calls in the
IRQ handler. This will also prevent an unneccesary FIQ interrupt
from being generated if the FIQ is enabled.
dwc_otg: fiq: prevent FIQ thrash and incorrect state passing to IRQ
In the case of a transaction to a device that had previously aborted
due to an error, several interrupts are enabled to reset the error
count when a device responds. This has the side-effect of making the
FIQ thrash because the hardware will generate multiple instances of
a NAK on an IN bulk/interrupt endpoint and multiple instances of ACK
on an OUT bulk/interrupt endpoint. Make the FIQ mask and clear the
associated interrupts.
Additionally, on non-split transactions make sure that only unmasked
interrupts are cleared. This caused a hard-to-trigger but serious
race condition when you had the combination of an endpoint awaiting
error recovery and a transaction completed on an endpoint - due to
the sequencing and timing of interrupts generated by the dwc_otg core,
it was possible to confuse the IRQ handler.
Fix function tracing
dwc_otg: whitespace cleanup in dwc_otg_urb_enqueue
dwc_otg: prevent OOPSes during device disconnects
The dwc_otg_urb_enqueue function is thread-unsafe. In particular the
access of urb->hcpriv, usb_hcd_link_urb_to_ep, dwc_otg_urb->qtd and
friends does not occur within a critical section and so if a device
was unplugged during activity there was a high chance that the
usbcore hub_thread would try to disable the endpoint with partially-
formed entries in the URB queue. This would result in BUG() or null
pointer dereferences.
Fix so that access of urb->hcpriv, enqueuing to the hardware and
adding to usbcore endpoint URB lists is contained within a single
critical section.
dwc_otg: prevent BUG() in TT allocation if hub address is > 16
A fixed-size array is used to track TT allocation. This was
previously set to 16 which caused a crash because
dwc_otg_hcd_allocate_port would read past the end of the array.
This was hit if a hub was plugged in which enumerated as addr > 16,
due to previous device resets or unplugs.
Also add #ifdef FIQ_DEBUG around hcd->hub_port_alloc[], which grows
to a large size if 128 hub addresses are supported. This field is
for debug only for tracking which frame an allocate happened in.
dwc_otg: make channel halts with unknown state less damaging
If the IRQ received a channel halt interrupt through the FIQ
with no other bits set, the IRQ would not release the host
channel and never complete the URB.
Add catchall handling to treat as a transaction error and retry.
dwc_otg: fiq_split: use TTs with more granularity
This fixes certain issues with split transaction scheduling.
- Isochronous multi-packet OUT transactions now hog the TT until
they are completed - this prevents hubs aborting transactions
if they get a periodic start-split out-of-order
- Don't perform TT allocation on non-periodic endpoints - this
allows simultaneous use of the TT's bulk/control and periodic
transaction buffers
This commit will mainly affect USB audio playback.
dwc_otg: fix potential sleep while atomic during urb enqueue
Fixes a regression introduced with eb1b482a. Kmalloc called from
dwc_otg_hcd_qtd_add / dwc_otg_hcd_qtd_create did not always have
the GPF_ATOMIC flag set. Force this flag when inside the larger
critical section.
dwc_otg: make fiq_split_enable imply fiq_fix_enable
Failing to set up the FIQ correctly would result in
"IRQ 32: nobody cared" errors in dmesg.
dwc_otg: prevent crashes on host port disconnects
Fix several issues resulting in crashes or inconsistent state
if a Model A root port was disconnected.
- Clean up queue heads properly in kill_urbs_in_qh_list by
removing the empty QHs from the schedule lists
- Set the halt status properly to prevent IRQ handlers from
using freed memory
- Add fiq_split related cleanup for saved registers
- Make microframe scheduling reclaim host channels if
active during a disconnect
- Abort URBs with -ESHUTDOWN status response, informing
device drivers so they respond in a more correct fashion
and don't try to resubmit URBs
- Prevent IRQ handlers from attempting to handle channel
interrupts if the associated URB was dequeued (and the
driver state was cleared)
dwc_otg: prevent leaking URBs during enqueue
A dwc_otg_urb would get leaked if the HCD enqueue function
failed for any reason. Free the URB at the appropriate points.
dwc_otg: Enable NAK holdoff for control split transactions
Certain low-speed devices take a very long time to complete a
data or status stage of a control transaction, producing NAK
responses until they complete internal processing - the USB2.0
spec limit is up to 500mS. This causes the same type of interrupt
storm as seen with USB-serial dongles prior to c8edb238.
In certain circumstances, usually while booting, this interrupt
storm could cause SD card timeouts.
dwc_otg: Fix for occasional lockup on boot when doing a USB reset
dwc_otg: Don't issue traffic to LS devices in FS mode
Issuing low-speed packets when the root port is in full-speed mode
causes the root port to stop responding. Explicitly fail when
enqueuing URBs to a LS endpoint on a FS bus.
Fix ARM architecture issue with local_irq_restore()
If local_fiq_enable() is called before a local_irq_restore(flags) where
the flags variable has the F bit set, the FIQ will be erroneously disabled.
Fixup arch_local_irq_restore to avoid trampling the F bit in CPSR.
Also fix some of the hacks previously implemented for previous dwc_otg
incarnations.
dwc_otg: fiq_fsm: Base commit for driver rewrite
This commit removes the previous FIQ fixes entirely and adds fiq_fsm.
This rewrite features much more complete support for split transactions
and takes into account several OTG hardware bugs. High-speed
isochronous transactions are also capable of being performed by fiq_fsm.
All driver options have been removed and replaced with:
- dwc_otg.fiq_enable (bool)
- dwc_otg.fiq_fsm_enable (bool)
- dwc_otg.fiq_fsm_mask (bitmask)
- dwc_otg.nak_holdoff (unsigned int)
Defaults are specified such that fiq_fsm behaves similarly to the
previously implemented FIQ fixes.
fiq_fsm: Push error recovery into the FIQ when fiq_fsm is used
If the transfer associated with a QTD failed due to a bus error, the HCD
would retry the transfer up to 3 times (implementing the USB2.0
three-strikes retry in software).
Due to the masking mechanism used by fiq_fsm, it is only possible to pass
a single interrupt through to the HCD per-transfer.
In this instance host channels would fall off the radar because the error
reset would function, but the subsequent channel halt would be lost.
Push the error count reset into the FIQ handler.
fiq_fsm: Implement timeout mechanism
For full-speed endpoints with a large packet size, interrupt latency
runs the risk of the FIQ starting a transaction too late in a full-speed
frame. If the device is still transmitting data when EOF2 for the
downstream frame occurs, the hub will disable the port. This change is
not reflected in the hub status endpoint and the device becomes
unresponsive.
Prevent high-bandwidth transactions from being started too late in a
frame. The mechanism is not guaranteed: a combination of bit stuffing
and hub latency may still result in a device overrunning.
fiq_fsm: fix bounce buffer utilisation for Isochronous OUT
Multi-packet isochronous OUT transactions were subject to a few bounday
bugs. Fix them.
Audio playback is now much more robust: however, an issue stands with
devices that have adaptive sinks - ALSA plays samples too fast.
dwc_otg: Return full-speed frame numbers in HS mode
The frame counter increments on every *microframe* in high-speed mode.
Most device drivers expect this number to be in full-speed frames - this
caused considerable confusion to e.g. snd_usb_audio which uses the
frame counter to estimate the number of samples played.
fiq_fsm: save PID on completion of interrupt OUT transfers
Also add edge case handling for interrupt transports.
Note that for periodic split IN, data toggles are unimplemented in the
OTG host hardware - it unconditionally accepts any PID.
fiq_fsm: add missing case for fiq_fsm_tt_in_use()
Certain combinations of bitrate and endpoint activity could
result in a periodic transaction erroneously getting started
while the previous Isochronous OUT was still active.
fiq_fsm: clear hcintmsk for aborted transactions
Prevents the FIQ from erroneously handling interrupts
on a timed out channel.
fiq_fsm: enable by default
fiq_fsm: fix dequeues for non-periodic split transactions
If a dequeue happened between the SSPLIT and CSPLIT phases of the
transaction, the HCD would never receive an interrupt.
fiq_fsm: Disable by default
fiq_fsm: Handle HC babble errors
The HCTSIZ transfer size field raises a babble interrupt if
the counter wraps. Handle the resulting interrupt in this case.
dwc_otg: fix interrupt registration for fiq_enable=0
Additionally make the module parameter conditional for wherever
hcd->fiq_state is touched.
fiq_fsm: Enable by default
dwc_otg: Fix various issues with root port and transaction errors
Process the host port interrupts correctly (and don't trample them).
Root port hotplug now functional again.
Fix a few thinkos with the transaction error passthrough for fiq_fsm.
fiq_fsm: Implement hack for Split Interrupt transactions
Hubs aren't too picky about which endpoint we send Control type split
transactions to. By treating Interrupt transfers as Control, it is
possible to use the non-periodic queue in the OTG core as well as the
non-periodic FIFOs in the hub itself. This massively reduces the
microframe exclusivity/contention that periodic split transactions
otherwise have to enforce.
It goes without saying that this is a fairly egregious USB specification
violation, but it works.
Original idea by Hans Petter Selasky @ FreeBSD.org.
dwc_otg: FIQ support on SMP. Set up FIQ stack and handler on Core 0 only.
dwc_otg: introduce fiq_fsm_spin(un|)lock()
SMP safety for the FIQ relies on register read-modify write cycles being
completed in the correct order. Several places in the DWC code modify
registers also touched by the FIQ. Protect these by a bare-bones lock
mechanism.
This also makes it possible to run the FIQ and IRQ handlers on different
cores.
fiq_fsm: fix build on bcm2708 and bcm2709 platforms
dwc_otg: put some barriers back where they should be for UP
bcm2709/dwc_otg: Setup FIQ on core 1 if >1 core active
dwc_otg: fixup read-modify-write in critical paths
Be more careful about read-modify-write on registers that the FIQ
also touches.
Guard fiq_fsm_spin_lock with fiq_enable check
fiq_fsm: Falling out of the state machine isn't fatal
This edge case can be hit if the port is disabled while the FIQ is
in the middle of a transaction. Make the effects less severe.
Also get rid of the useless return value.
squash: dwc_otg: Allow to build without SMP
usb: core: make overcurrent messages more prominent
Hub overcurrent messages are more serious than "debug". Increase loglevel.
usb: dwc_otg: Don't use dma_to_virt()
Commit 6ce0d20 changes dma_to_virt() which breaks this driver.
Open code the old dma_to_virt() implementation to work around this.
Limit the use of __bus_to_virt() to cases where transfer_buffer_length
is set and transfer_buffer is not set. This is done to increase the
chance that this driver will also work on ARCH_BCM2835.
transfer_buffer should not be NULL if the length is set, but the
comment in the code indicates that there are situations where this
might happen. drivers/usb/isp1760/isp1760-hcd.c also has a similar
comment pointing to a possible: 'usb storage / SCSI bug'.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: Fix crash when fiq_enable=0
dwc_otg: fiq_fsm: Make high-speed isochronous strided transfers work properly
Certain low-bandwidth high-speed USB devices (specialist audio devices,
compressed-frame webcams) have packet intervals > 1 microframe.
Stride these transfers in the FIQ by using the start-of-frame interrupt
to restart the channel at the right time.
dwc_otg: Force host mode to fix incorrect compute module boards
dwc_otg: Add ARCH_BCM2835 support
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: Simplify FIQ irq number code
Dropping ATAGS means we can simplify the FIQ irq number code.
Also add error checking on the returned irq number.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: Remove duplicate gadget probe/unregister function
dwc_otg: Properly set the HFIR
Douglas Anderson reported:
According to the most up to date version of the dwc2 databook, the FRINT
field of the HFIR register should be programmed to:
* 125 us * (PHY clock freq for HS) - 1
* 1000 us * (PHY clock freq for FS/LS) - 1
This is opposed to older versions of the doc that claimed it should be:
* 125 us * (PHY clock freq for HS)
* 1000 us * (PHY clock freq for FS/LS)
and reported lower timing jitter on a USB analyser
dcw_otg: trim xfer length when buffer larger than allocated size is received
dwc_otg: Don't free qh align buffers in atomic context
dwc_otg: Enable the hack for Split Interrupt transactions by default
dwc_otg.fiq_fsm_mask=0xF has long been a suggestion for users with audio stutters or other USB bandwidth issues.
So far we are aware of many success stories but no failure caused by this setting.
Make it a default to learn more.
See: https://www.raspberrypi.org/forums/viewtopic.php?f=28&t=70437
Signed-off-by: popcornmix <popcornmix@gmail.com>
dwc_otg: Use kzalloc when suitable
dwc_otg: Pass struct device to dma_alloc*()
This makes it possible to get the bus address from Device Tree.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: popcornmix <popcornmix@gmail.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2709: Drop platform smp and timer init code
irq-bcm2836 handles this through these functions:
bcm2835_init_local_timer_frequency()
bcm2836_arm_irqchip_smp_init()
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm270x: Use watchdog for reboot/poweroff
The watchdog driver already has support for reboot/poweroff.
Make use of this and remove the code from the platform files.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
so that special/critical clocks can get enabled early on
in the boot process avoiding the risk of disabling a clock,
pll_divider or pll when a claiming driver fails to install
propperly - maybe it needs to defer.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
The Raspberry Pi firmware looks at the RSTS register to know which
partition to boot from. The reboot syscall command
LINUX_REBOOT_CMD_RESTART2 supports passing in a string argument.
Add support for passing in a partition number 0..63 to boot from.
Partition 63 is a special partiton indicating halt.
If the partition doesn't exist, the firmware falls back to partition 0.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Load driver early since at least bcm2708_fb doesn't support deferred
probing and even if it did, we don't want the video driver deferred.
Support the legacy DMA API which is needed by bcm2708_fb.
Don't mask out channel 2.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
The VideoCore bootloader passes in Serial number and
Revision number through Device Tree. Make these available to
userspace through /proc/cpuinfo.
Mainline status:
There is a commit in linux-next that standardize passing the serial
number through Device Tree (string: /serial-number):
ARM: 8355/1: arch: Show the serial number from devicetree in cpuinfo
There was an attempt to do the same with the revision number, but it
didn't get in:
[PATCH v2 1/2] arm: devtree: Set system_rev from DT revision
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
The spi-bcm2835 driver automatically uses GPIO chip-selects due to
some unreliability of the native ones. In doing so it chooses the
same pins as the native chip-selects would use, but the existing
code always uses pins 7 and 8, wherever the SPI function is mapped.
Search the pinctrl group assigned to the driver for pins that
correspond to native chip-selects, and use those for GPIO chip-
selects.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Although the GPIO controller can generate three interrupts (four counting
the common one), the device tree files currently only specify two. In the
absence of the third, simply don't register that interrupt (as opposed to
registering 0), which has the effect of making it impossible to generate
interrupts for GPIOs 46-53 which, since they share pins with the SD card
interface, is unlikely to be a problem.
Add a duplicate irq range with an offset on the hwirq's so the
driver can detect that enable_fiq() is used.
Tested with downstream dwc_otg USB controller driver.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
The old arch-specific IRQ macros included a dsb to ensure the
write to clear the mailbox interrupt completed before returning
from the interrupt. The BCM2836 irqchip driver needs the same
precaution to avoid spurious interrupts.
Spurious interrupts are still possible for other reasons,
though, so trap them early.
See commit dae803e165 -- the warning is
expected sometimes when using CMA. However, that commit still spams
my kernel log with these warnings.
Signed-off-by: Eric Anholt <eric@anholt.net>
smsc95xx is adjusting truesize when it shouldn't, and following a recent patch from Eric this is now triggering warnings.
This patch stops smsc95xx from changing truesize.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
commit 6330d55347 upstream.
When built as a module and running with update_ms >= 0, pstore will Oops
during module unload since the work timer is still running. This makes sure
the worker is stopped before unloading.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 041939c1ec upstream.
After commit c950fd6f20 kernel registers pstore write based on flag set.
Pstore write for powerpc is broken as flags(PSTORE_FLAGS_DMESG) is not set for
powerpc architecture. On panic, kernel doesn't write message to
/fs/pstore/dmesg*(Entry doesn't gets created at all).
This patch enables pstore write for powerpc architecture by setting
PSTORE_FLAGS_DMESG flag.
Fixes: c950fd6f20 ("pstore: Split pstore fragile flags")
Signed-off-by: Ankit Kumar <ankit@linux.vnet.ibm.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d5483feda8 upstream.
Fix failures to create namespaces due to the vmem_altmap not advertising
enough free space to store the memmap.
WARNING: CPU: 15 PID: 8022 at arch/x86/mm/init_64.c:656 arch_add_memory+0xde/0xf0
[..]
Call Trace:
dump_stack+0x63/0x83
__warn+0xcb/0xf0
warn_slowpath_null+0x1d/0x20
arch_add_memory+0xde/0xf0
devm_memremap_pages+0x244/0x440
pmem_attach_disk+0x37e/0x490 [nd_pmem]
nd_pmem_probe+0x7e/0xa0 [nd_pmem]
nvdimm_bus_probe+0x71/0x120 [libnvdimm]
driver_probe_device+0x2bb/0x460
bind_store+0x114/0x160
drv_attr_store+0x25/0x30
In commit 658922e57b "libnvdimm, pfn: fix memmap reservation sizing"
we arranged for the capacity to be allocated, but failed to also update
the 'npfns' parameter. This leads to cases where there is enough
capacity reserved to hold all the allocated sections, but
vmemmap_populate_hugepages() still encounters -ENOMEM from
altmap_alloc_block_buf().
This fix is a stop-gap until we can teach the core memory hotplug
implementation to permit sub-section hotplug.
Fixes: 658922e57b ("libnvdimm, pfn: fix memmap reservation sizing")
Reported-by: Anisha Allada <anisha.allada@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 452bae0aed upstream.
A debug patch to turn the standard device_lock() into something that
lockdep can analyze yielded the following:
======================================================
[ INFO: possible circular locking dependency detected ]
4.11.0-rc4+ #106 Tainted: G O
-------------------------------------------------------
lt-libndctl/1898 is trying to acquire lock:
(&dev->nvdimm_mutex/3){+.+.+.}, at: [<ffffffffc023c948>] nd_attach_ndns+0x178/0x1b0 [libnvdimm]
but task is already holding lock:
(&nvdimm_bus->reconfig_mutex){+.+.+.}, at: [<ffffffffc022e0b1>] nvdimm_bus_lock+0x21/0x30 [libnvdimm]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&nvdimm_bus->reconfig_mutex){+.+.+.}:
lock_acquire+0xf6/0x1f0
__mutex_lock+0x88/0x980
mutex_lock_nested+0x1b/0x20
nvdimm_bus_lock+0x21/0x30 [libnvdimm]
nvdimm_namespace_capacity+0x1b/0x40 [libnvdimm]
nvdimm_namespace_common_probe+0x230/0x510 [libnvdimm]
nd_pmem_probe+0x14/0x180 [nd_pmem]
nvdimm_bus_probe+0xa9/0x260 [libnvdimm]
-> #0 (&dev->nvdimm_mutex/3){+.+.+.}:
__lock_acquire+0x1107/0x1280
lock_acquire+0xf6/0x1f0
__mutex_lock+0x88/0x980
mutex_lock_nested+0x1b/0x20
nd_attach_ndns+0x178/0x1b0 [libnvdimm]
nd_namespace_store+0x308/0x3c0 [libnvdimm]
namespace_store+0x87/0x220 [libnvdimm]
In this case '&dev->nvdimm_mutex/3' mirrors '&dev->mutex'.
Fix this by replacing the use of device_lock() with nvdimm_bus_lock() to protect
nd_{attach,detach}_ndns() operations.
Fixes: 8c2f7e8658 ("libnvdimm: infrastructure for btt devices")
Reported-by: Yi Zhang <yizhan@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b2518c78ce upstream.
The following BUG was observed when nd_pmem_notify() was called
for a BTT device. The use of a pmem_device pointer is not valid
with BTT.
BUG: unable to handle kernel NULL pointer dereference at 0000000000000030
IP: nd_pmem_notify+0x30/0xf0 [nd_pmem]
Call Trace:
nd_device_notify+0x40/0x50
child_notify+0x10/0x20
device_for_each_child+0x50/0x90
nd_region_notify+0x20/0x30
nd_device_notify+0x40/0x50
nvdimm_region_notify+0x27/0x30
acpi_nfit_scrub+0x341/0x590 [nfit]
process_one_work+0x197/0x450
worker_thread+0x4e/0x4a0
kthread+0x109/0x140
Fix nd_pmem_notify() by setting nd_region and badblocks pointers
properly for BTT.
Cc: Vishal Verma <vishal.l.verma@intel.com>
Fixes: 719994660c ("libnvdimm: async notification support")
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bc042fdfbb upstream.
In the case where a dimm does not have any associated flush hints the
ndrd->flush_wpq array may be uninitialized leading to crashes with the
following signature:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000010
IP: region_visible+0x10f/0x160 [libnvdimm]
Call Trace:
internal_create_group+0xbe/0x2f0
sysfs_create_groups+0x40/0x80
device_add+0x2d8/0x650
nd_async_device_register+0x12/0x40 [libnvdimm]
async_run_entry_fn+0x39/0x170
process_one_work+0x212/0x6c0
? process_one_work+0x197/0x6c0
worker_thread+0x4e/0x4a0
kthread+0x10c/0x140
? process_one_work+0x6c0/0x6c0
? kthread_create_on_node+0x60/0x60
ret_from_fork+0x31/0x40
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Fixes: f284a4f237 ("libnvdimm: introduce nvdimm_flush() and nvdimm_has_flush()")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6de65fcfdb upstream.
msg_written_handler() may set ssif_info->multi_data to NULL
when using ipmitool to write fru.
Before setting ssif_info->multi_data to NULL, add new local
pointer "data_to_send" and store correct i2c data pointer to
it to fix NULL pointer kernel panic and incorrect ssif_info->multi_pos.
Signed-off-by: Joeseph Chang <joechang@codeaurora.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dcb9cfaa5e upstream.
Make sure to check the tty-device pointer before looking up the sibling
platform device to avoid dereferencing a NULL-pointer when the tty is
one end of a Unix98 pty.
Fixes: 74cdad37cd ("Bluetooth: hci_intel: Add runtime PM support")
Fixes: 1ab1f239bf ("Bluetooth: hci_intel: Add support for platform driver")
Cc: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 95065a61e9 upstream.
Make sure to check the tty-device pointer before looking up the sibling
platform device to avoid dereferencing a NULL-pointer when the tty is
one end of a Unix98 pty.
Fixes: 0395ffc1ee ("Bluetooth: hci_bcm: Add PM for BCM devices")
Cc: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ab89f0bdd6 upstream.
Running 32bit userspace on 64bit kernel results in MSG_CMSG_COMPAT being
defined as 0x80000000. This results in sendmsg failure if used from 32bit
userspace running on 64bit kernel. Fix this by accounting for MSG_CMSG_COMPAT
in flags check in hci_sock_sendmsg.
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Signed-off-by: Marko Kiiskila <marko@runtime.io>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 77dae61344 upstream.
While using emacs, cat or others' commands in konsole with recent
kernels, I have met many times that CTRL-C freeze konsole. After
konsole freeze I can't type anything, then I have to open a new one,
it is very annoying.
See bug report:
https://bugs.kde.org/show_bug.cgi?id=175283
The platform in that bug report is Solaris, but now the pty in linux
has the same problem or the same behavior as Solaris :)
It has high possibility to trigger the problem follow steps below:
Note: In my test, BigFile is a text file whose size is bigger than 1G
1:open konsole
1:cat BigFile
2:CTRL-C
After some digging, I find out the reason is that commit 1d1d14da12
("pty: Fix buffer flush deadlock") changes the behavior of pty_flush_buffer.
Thread A Thread B
-------- --------
1:n_tty_poll return POLLIN
2:CTRL-C trigger pty_flush_buffer
tty_buffer_flush
n_tty_flush_buffer
3:attempt to check count of chars:
ioctl(fd, TIOCINQ, &available)
available is equal to 0
4:read(fd, buffer, avaiable)
return 0
5:konsole close fd
Yes, I know we could use the same patch included in the BUG report as
a workaround for linux platform too. But I think the data in ldisc is
belong to application of another side, we shouldn't clear it when we
want to flush write buffer of this side in pty_flush_buffer. So I think
it is better to disable ldisc flush in pty_flush_buffer, because its new
hehavior bring no benefit except that it mess up the behavior between
POLLIN, and TIOCINQ or FIONREAD.
Also I find no flush_buffer function in others' tty driver has the
same behavior as current pty_flush_buffer.
Fixes: 1d1d14da12 ("pty: Fix buffer flush deadlock")
Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 77e6fe7fd2 upstream.
Make sure to actually suspend the device before returning after a failed
(or deferred) probe.
Note that autosuspend must be disabled before runtime pm is disabled in
order to balance the usage count due to a negative autosuspend delay as
well as to make the final put suspend the device synchronously.
Fixes: 388bc26226 ("omap-serial: Fix the error handling in the omap_serial probe")
Cc: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 099bd73dc1 upstream.
An unbalanced and misplaced synchronous put was used to suspend the
device on driver unbind, something which with a likewise misplaced
pm_runtime_disable leads to external aborts when an open port is being
removed.
Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa024010
...
[<c046e760>] (serial_omap_set_mctrl) from [<c046a064>] (uart_update_mctrl+0x50/0x60)
[<c046a064>] (uart_update_mctrl) from [<c046a400>] (uart_shutdown+0xbc/0x138)
[<c046a400>] (uart_shutdown) from [<c046bd2c>] (uart_hangup+0x94/0x190)
[<c046bd2c>] (uart_hangup) from [<c045b760>] (__tty_hangup+0x404/0x41c)
[<c045b760>] (__tty_hangup) from [<c045b794>] (tty_vhangup+0x1c/0x20)
[<c045b794>] (tty_vhangup) from [<c046ccc8>] (uart_remove_one_port+0xec/0x260)
[<c046ccc8>] (uart_remove_one_port) from [<c046ef4c>] (serial_omap_remove+0x40/0x60)
[<c046ef4c>] (serial_omap_remove) from [<c04845e8>] (platform_drv_remove+0x34/0x4c)
Fix this up by resuming the device before deregistering the port and by
suspending and disabling runtime pm only after the port has been
removed.
Also make sure to disable autosuspend before disabling runtime pm so
that the usage count is balanced and device actually suspended before
returning.
Note that due to a negative autosuspend delay being set in probe, the
unbalanced put would actually suspend the device on first driver unbind,
while rebinding and again unbinding would result in a negative
power.usage_count.
Fixes: 7e9c8e7dbf ("serial: omap: make sure to suspend device before remove")
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 768d64f491 upstream.
Driver should provide its own struct device for all DMA-mapping calls instead
of extracting device pointer from DMA engine channel. Although this is harmless
from the driver operation perspective on ARM architecture, it is always good
to use the DMA mapping API in a proper way. This patch fixes following DMA API
debug warning:
WARNING: CPU: 0 PID: 0 at lib/dma-debug.c:1241 check_sync+0x520/0x9f4
samsung-uart 12c20000.serial: DMA-API: device driver tries to sync DMA memory it has not allocated [device address=0x000000006df0f580] [size=64 bytes]
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.11.0-rc1-00137-g07ca963 #51
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[<c011aaa4>] (unwind_backtrace) from [<c01127c0>] (show_stack+0x20/0x24)
[<c01127c0>] (show_stack) from [<c06ba5d8>] (dump_stack+0x84/0xa0)
[<c06ba5d8>] (dump_stack) from [<c0139528>] (__warn+0x14c/0x180)
[<c0139528>] (__warn) from [<c01395a4>] (warn_slowpath_fmt+0x48/0x50)
[<c01395a4>] (warn_slowpath_fmt) from [<c0729058>] (check_sync+0x520/0x9f4)
[<c0729058>] (check_sync) from [<c072967c>] (debug_dma_sync_single_for_device+0x88/0xc8)
[<c072967c>] (debug_dma_sync_single_for_device) from [<c0803c10>] (s3c24xx_serial_start_tx_dma+0x100/0x2f8)
[<c0803c10>] (s3c24xx_serial_start_tx_dma) from [<c0804338>] (s3c24xx_serial_tx_chars+0x198/0x33c)
Reported-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Fixes: 62c37eedb7 ("serial: samsung: add dma reqest/release functions")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 272f98f684 upstream.
To mitigate some types of offline attacks, filesystem encryption is
designed to enforce that all files in an encrypted directory tree use
the same encryption policy (i.e. the same encryption context excluding
the nonce). However, the fscrypt_has_permitted_context() function which
enforces this relies on comparing struct fscrypt_info's, which are only
available when we have the encryption keys. This can cause two
incorrect behaviors:
1. If we have the parent directory's key but not the child's key, or
vice versa, then fscrypt_has_permitted_context() returned false,
causing applications to see EPERM or ENOKEY. This is incorrect if
the encryption contexts are in fact consistent. Although we'd
normally have either both keys or neither key in that case since the
master_key_descriptors would be the same, this is not guaranteed
because keys can be added or removed from keyrings at any time.
2. If we have neither the parent's key nor the child's key, then
fscrypt_has_permitted_context() returned true, causing applications
to see no error (or else an error for some other reason). This is
incorrect if the encryption contexts are in fact inconsistent, since
in that case we should deny access.
To fix this, retrieve and compare the fscrypt_contexts if we are unable
to set up both fscrypt_infos.
While this slightly hurts performance when accessing an encrypted
directory tree without the key, this isn't a case we really need to be
optimizing for; access *with* the key is much more important.
Furthermore, the performance hit is barely noticeable given that we are
already retrieving the fscrypt_context and doing two keyring searches in
fscrypt_get_encryption_info(). If we ever actually wanted to optimize
this case we might start by caching the fscrypt_contexts.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd656375f9 upstream.
Currently, we didn't invalidate page tables during invalidate_inode_pages2()
for DAX. That could result in e.g. 2MiB zero page being mapped into
page tables while there were already underlying blocks allocated and
thus data seen through mmap were different from data seen by read(2).
The following sequence reproduces the problem:
- open an mmap over a 2MiB hole
- read from a 2MiB hole, faulting in a 2MiB zero page
- write to the hole with write(3p). The write succeeds but we
incorrectly leave the 2MiB zero page mapping intact.
- via the mmap, read the data that was just written. Since the zero
page mapping is still intact we read back zeroes instead of the new
data.
Fix the problem by unconditionally calling invalidate_inode_pages2_range()
in dax_iomap_actor() for new block allocations and by properly
invalidating page tables in invalidate_inode_pages2_range() for DAX
mappings.
Fixes: c6dcf52c23
Link: http://lkml.kernel.org/r/20170510085419.27601-3-jack@suse.cz
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4636e70bb0 upstream.
Patch series "mm,dax: Fix data corruption due to mmap inconsistency",
v4.
This series fixes data corruption that can happen for DAX mounts when
page faults race with write(2) and as a result page tables get out of
sync with block mappings in the filesystem and thus data seen through
mmap is different from data seen through read(2).
The series passes testing with t_mmap_stale test program from Ross and
also other mmap related tests on DAX filesystem.
This patch (of 4):
dax_invalidate_mapping_entry() currently removes DAX exceptional entries
only if they are clean and unlocked. This is done via:
invalidate_mapping_pages()
invalidate_exceptional_entry()
dax_invalidate_mapping_entry()
However, for page cache pages removed in invalidate_mapping_pages()
there is an additional criteria which is that the page must not be
mapped. This is noted in the comments above invalidate_mapping_pages()
and is checked in invalidate_inode_page().
For DAX entries this means that we can can end up in a situation where a
DAX exceptional entry, either a huge zero page or a regular DAX entry,
could end up mapped but without an associated radix tree entry. This is
inconsistent with the rest of the DAX code and with what happens in the
page cache case.
We aren't able to unmap the DAX exceptional entry because according to
its comments invalidate_mapping_pages() isn't allowed to block, and
unmap_mapping_range() takes a write lock on the mapping->i_mmap_rwsem.
Since we essentially never have unmapped DAX entries to evict from the
radix tree, just remove dax_invalidate_mapping_entry().
Fixes: c6dcf52c23 ("mm: Invalidate DAX radix tree entries only if appropriate")
Link: http://lkml.kernel.org/r/20170510085419.27601-2-jack@suse.cz
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Reported-by: Jan Kara <jack@suse.cz>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 565851c972 upstream.
Usage of device_lock() for dax_region attributes is unnecessary and
deadlock prone. It's unnecessary because the order of registration /
un-registration guarantees that drvdata is always valid. It's deadlock
prone because it sets up this situation:
ndctl D 0 2170 2082 0x00000000
Call Trace:
__schedule+0x31f/0x980
schedule+0x3d/0x90
schedule_preempt_disabled+0x15/0x20
__mutex_lock+0x402/0x980
? __mutex_lock+0x158/0x980
? align_show+0x2b/0x80 [dax]
? kernfs_seq_start+0x2f/0x90
mutex_lock_nested+0x1b/0x20
align_show+0x2b/0x80 [dax]
dev_attr_show+0x20/0x50
ndctl D 0 2186 2079 0x00000000
Call Trace:
__schedule+0x31f/0x980
schedule+0x3d/0x90
__kernfs_remove+0x1f6/0x340
? kernfs_remove_by_name_ns+0x45/0xa0
? remove_wait_queue+0x70/0x70
kernfs_remove_by_name_ns+0x45/0xa0
remove_files.isra.1+0x35/0x70
sysfs_remove_group+0x44/0x90
sysfs_remove_groups+0x2e/0x50
dax_region_unregister+0x25/0x40 [dax]
devm_action_release+0xf/0x20
release_nodes+0x16d/0x2b0
devres_release_all+0x3c/0x60
device_release_driver_internal+0x17d/0x220
device_release_driver+0x12/0x20
unbind_store+0x112/0x160
ndctl/2170 is trying to acquire the device_lock() to read an attribute,
and ndctl/2186 is holding the device_lock() while trying to drain all
active attribute readers.
Thanks to Yi Zhang for the reproduction script.
Fixes: d7fe1a67f6 ("dax: add region 'id', 'size', and 'align' attributes")
Reported-by: Yi Zhang <yizhan@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ed01e50acd upstream.
If device_add() fails, cleanup the cdev. Otherwise, we leak a kobj_map()
with a stale device number.
As Jason points out, there is a small possibility that userspace has
opened and mapped the device in the time between cdev_add() and the
device_add() failure. We need a new kill_dax_dev() helper to invalidate
any established mappings.
Fixes: ba09c01d2f ("dax: convert to the cdev api")
Reported-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c9d5b127f upstream.
fix_sync_read_error() modifies a bio on a newly faulty
device by setting bi_end_io to end_sync_write.
This ensure that put_buf() will still call rdev_dec_pending()
as required, but makes sure that subsequent code in
fix_sync_read_error() doesn't try to read from the device.
Unfortunately this interacts badly with sync_request_write()
which assumes that any bio with bi_end_io set to non-NULL
other than end_sync_read is safe to write to.
As the device is now faulty it doesn't make sense to write.
As the bio was recently used for a read, it is "dirty"
and not suitable for immediate submission.
In particular, ->bi_next might be non-NULL, which will cause
generic_make_request() to complain.
Break this interaction by refusing to write to devices
which are marked as Faulty.
Reported-and-tested-by: Michael Wang <yun.wang@profitbricks.com>
Fixes: 2e52d449bc ("md/raid1: add failfast handling for reads.")
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07a77929ba upstream.
The author meant to free the variable that was just allocated, instead
of the one that failed to be allocated, but made a simple typo. This
patch rectifies that.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a99f3c83d upstream.
The optimization for opaque dir create was wrongly being applied
also to non-dir create.
Fixes: 97c684cc91 ("ovl: create directories inside merged parent opaque")
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 85435d7a15 upstream.
SFM is mapping doublequote to 0xF020
Without this patch creating files with doublequote fails to Windows/Mac
Signed-off-by: Bjoern Jacke <bjacke@samba.org>
Signed-off-by: Steve French <smfrench@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d8a6e505d6 upstream.
An open directory may have a NULL private_data pointer prior to readdir.
Fixes: 0de1f4c6f6 ("Add way to query server fs info for smb3")
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Steve French <smfrench@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3998e6b87d upstream.
When the final cifsFileInfo_put() is called from cifsiod and an oplock
break work is queued, lockdep complains loudly:
=============================================
[ INFO: possible recursive locking detected ]
4.11.0+ #21 Not tainted
---------------------------------------------
kworker/0:2/78 is trying to acquire lock:
("cifsiod"){++++.+}, at: flush_work+0x215/0x350
but task is already holding lock:
("cifsiod"){++++.+}, at: process_one_work+0x255/0x8e0
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock("cifsiod");
lock("cifsiod");
*** DEADLOCK ***
May be due to missing lock nesting notation
2 locks held by kworker/0:2/78:
#0: ("cifsiod"){++++.+}, at: process_one_work+0x255/0x8e0
#1: ((&wdata->work)){+.+...}, at: process_one_work+0x255/0x8e0
stack backtrace:
CPU: 0 PID: 78 Comm: kworker/0:2 Not tainted 4.11.0+ #21
Workqueue: cifsiod cifs_writev_complete
Call Trace:
dump_stack+0x85/0xc2
__lock_acquire+0x17dd/0x2260
? match_held_lock+0x20/0x2b0
? trace_hardirqs_off_caller+0x86/0x130
? mark_lock+0xa6/0x920
lock_acquire+0xcc/0x260
? lock_acquire+0xcc/0x260
? flush_work+0x215/0x350
flush_work+0x236/0x350
? flush_work+0x215/0x350
? destroy_worker+0x170/0x170
__cancel_work_timer+0x17d/0x210
? ___preempt_schedule+0x16/0x18
cancel_work_sync+0x10/0x20
cifsFileInfo_put+0x338/0x7f0
cifs_writedata_release+0x2a/0x40
? cifs_writedata_release+0x2a/0x40
cifs_writev_complete+0x29d/0x850
? preempt_count_sub+0x18/0xd0
process_one_work+0x304/0x8e0
worker_thread+0x9b/0x6a0
kthread+0x1b2/0x200
? process_one_work+0x8e0/0x8e0
? kthread_create_on_node+0x40/0x40
ret_from_fork+0x31/0x40
This is a real warning. Since the oplock is queued on the same
workqueue this can deadlock if there is only one worker thread active
for the workqueue (which will be the case during memory pressure when
the rescuer thread is handling it).
Furthermore, there is at least one other kind of hang possible due to
the oplock break handling if there is only worker. (This can be
reproduced without introducing memory pressure by having passing 1 for
the max_active parameter of cifsiod.) cifs_oplock_break() can wait
indefintely in the filemap_fdatawait() while the cifs_writev_complete()
work is blocked:
sysrq: SysRq : Show Blocked State
task PC stack pid father
kworker/0:1 D 0 16 2 0x00000000
Workqueue: cifsiod cifs_oplock_break
Call Trace:
__schedule+0x562/0xf40
? mark_held_locks+0x4a/0xb0
schedule+0x57/0xe0
io_schedule+0x21/0x50
wait_on_page_bit+0x143/0x190
? add_to_page_cache_lru+0x150/0x150
__filemap_fdatawait_range+0x134/0x190
? do_writepages+0x51/0x70
filemap_fdatawait_range+0x14/0x30
filemap_fdatawait+0x3b/0x40
cifs_oplock_break+0x651/0x710
? preempt_count_sub+0x18/0xd0
process_one_work+0x304/0x8e0
worker_thread+0x9b/0x6a0
kthread+0x1b2/0x200
? process_one_work+0x8e0/0x8e0
? kthread_create_on_node+0x40/0x40
ret_from_fork+0x31/0x40
dd D 0 683 171 0x00000000
Call Trace:
__schedule+0x562/0xf40
? mark_held_locks+0x29/0xb0
schedule+0x57/0xe0
io_schedule+0x21/0x50
wait_on_page_bit+0x143/0x190
? add_to_page_cache_lru+0x150/0x150
__filemap_fdatawait_range+0x134/0x190
? do_writepages+0x51/0x70
filemap_fdatawait_range+0x14/0x30
filemap_fdatawait+0x3b/0x40
filemap_write_and_wait+0x4e/0x70
cifs_flush+0x6a/0xb0
filp_close+0x52/0xa0
__close_fd+0xdc/0x150
SyS_close+0x33/0x60
entry_SYSCALL_64_fastpath+0x1f/0xbe
Showing all locks held in the system:
2 locks held by kworker/0:1/16:
#0: ("cifsiod"){.+.+.+}, at: process_one_work+0x255/0x8e0
#1: ((&cfile->oplock_break)){+.+.+.}, at: process_one_work+0x255/0x8e0
Showing busy workqueues and worker pools:
workqueue cifsiod: flags=0xc
pwq 0: cpus=0 node=0 flags=0x0 nice=0 active=1/1
in-flight: 16:cifs_oplock_break
delayed: cifs_writev_complete, cifs_echo_request
pool 0: cpus=0 node=0 flags=0x0 nice=0 hung=0s workers=3 idle: 750 3
Fix these problems by creating a a new workqueue (with a rescuer) for
the oplock break work.
Signed-off-by: Rabin Vincent <rabinv@axis.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6026685de3 upstream.
As with 618763958b, an open directory may have a NULL private_data
pointer prior to readdir. CIFS_ENUMERATE_SNAPSHOTS must check for this
before dereference.
Fixes: 834170c859 ("Enable previous version support")
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Steve French <smfrench@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0e5c795592 upstream.
The server may respond with success, and an output buffer less than
sizeof(struct smb_snapshot_array) in length. Do not leak the output
buffer in this case.
Fixes: 834170c859 ("Enable previous version support")
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Steve French <smfrench@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b704e70b7c upstream.
- trailing space maps to 0xF028
- trailing period maps to 0xF029
This fix corrects the mapping of file names which have a trailing character
that would otherwise be illegal (period or space) but is allowed by POSIX.
Signed-off-by: Bjoern Jacke <bjacke@samba.org>
Signed-off-by: Steve French <smfrench@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7db0a6efdc upstream.
Macs send the maximum buffer size in response on ioctl to validate
negotiate security information, which causes us to fail the mount
as the response buffer is larger than the expected response.
Changed ioctl response processing to allow for padding of validate
negotiate ioctl response and limit the maximum response size to
maximum buffer size.
Signed-off-by: Steve French <steve.french@primarydata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26c9cb668c upstream.
Mac requires the unicode flag to be set for cifs, even for the smb
echo request (which doesn't have strings).
Without this Mac rejects the periodic echo requests (when mounting
with cifs) that we use to check if server is down
Signed-off-by: Steve French <smfrench@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd8c42968e upstream.
Incorrect return value for shares not using the prefix path means that
we will never match superblocks for these shares.
Fixes: commit c1d8b24d18 ("Compare prepaths when comparing superblocks")
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 62be1511b1 upstream.
Patch series "more robust PF_MEMALLOC handling"
This series aims to unify the setting and clearing of PF_MEMALLOC, which
prevents recursive reclaim. There are some places that clear the flag
unconditionally from current->flags, which may result in clearing a
pre-existing flag. This already resulted in a bug report that Patch 1
fixes (without the new helpers, to make backporting easier). Patch 2
introduces the new helpers, modelled after existing memalloc_noio_* and
memalloc_nofs_* helpers, and converts mm core to use them. Patches 3
and 4 convert non-mm code.
This patch (of 4):
__alloc_pages_direct_compact() sets PF_MEMALLOC to prevent deadlock
during page migration by lock_page() (see the comment in
__unmap_and_move()). Then it unconditionally clears the flag, which can
clear a pre-existing PF_MEMALLOC flag and result in recursive reclaim.
This was not a problem until commit a8161d1ed6 ("mm, page_alloc:
restructure direct compaction handling in slowpath"), because direct
compation was called only after direct reclaim, which was skipped when
PF_MEMALLOC flag was set.
Even now it's only a theoretical issue, as the new callsite of
__alloc_pages_direct_compact() is reached only for costly orders and
when gfp_pfmemalloc_allowed() is true, which means either
__GFP_NOMEMALLOC is in gfp_flags or in_interrupt() is true. There is no
such known context, but let's play it safe and make
__alloc_pages_direct_compact() robust for cases where PF_MEMALLOC is
already set.
Fixes: a8161d1ed6 ("mm, page_alloc: restructure direct compaction handling in slowpath")
Link: http://lkml.kernel.org/r/20170405074700.29871-2-vbabka@suse.cz
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Reported-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Hillf Danton <hillf.zj@alibaba-inc.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Chris Leech <cleech@redhat.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Josef Bacik <jbacik@fb.com>
Cc: Lee Duncan <lduncan@suse.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81be3dee96 upstream.
getxattr uses vmalloc to allocate memory if kzalloc fails. This is
filled by vfs_getxattr and then copied to the userspace. vmalloc,
however, doesn't zero out the memory so if the specific implementation
of the xattr handler is sloppy we can theoretically expose a kernel
memory. There is no real sign this is really the case but let's make
sure this will not happen and use vzalloc instead.
Fixes: 779302e678 ("fs/xattr.c:getxattr(): improve handling of allocation failures")
Link: http://lkml.kernel.org/r/20170306103327.2766-1-mhocko@kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Reported-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 53950ef541 upstream.
Let the server figure this out because our size might be out of date or
not present.
The bug was that
xfs_io -f -t -c "pread -v 0 100" /mnt/foo
echo "Test" > /mnt/foo
xfs_io -f -t -c "pread -v 0 100" /mnt/foo
fails because the second truncate did not happen if nothing had
requested the size after the write in echo. Thus i_size was zero (not
present) and the orangefs_setattr though i_size was zero and there was
nothing to do.
Signed-off-by: Martin Brandenburg <martin@omnibond.com>
Signed-off-by: Mike Marshall <hubcap@omnibond.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 17930b252c upstream.
Since orangefs_lookup calls orangefs_iget which calls
orangefs_inode_getattr, getattr_time will get set.
Signed-off-by: Martin Brandenburg <martin@omnibond.com>
Signed-off-by: Mike Marshall <hubcap@omnibond.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e675c5ec51 upstream.
Also don't check flags as this has been validated by the VFS already.
Fix an off-by-one error in the max size checking.
Stop logging just because userspace wants to write attributes which do
not fit.
This and the previous commit fix xfstests generic/020.
Signed-off-by: Martin Brandenburg <martin@omnibond.com>
Signed-off-by: Mike Marshall <hubcap@omnibond.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b4cc9787f upstream.
Currently the case of writing via mmap to a file with inline data is not
handled. This is maybe a rare case since it requires a writable memory
map of a very small file, but it is trivial to trigger with on
inline_data filesystem, and it causes the
'BUG_ON(ext4_test_inode_state(inode, EXT4_STATE_MAY_INLINE_DATA));' in
ext4_writepages() to be hit:
mkfs.ext4 -O inline_data /dev/vdb
mount /dev/vdb /mnt
xfs_io -f /mnt/file \
-c 'pwrite 0 1' \
-c 'mmap -w 0 1m' \
-c 'mwrite 0 1' \
-c 'fsync'
kernel BUG at fs/ext4/inode.c:2723!
invalid opcode: 0000 [#1] SMP
CPU: 1 PID: 2532 Comm: xfs_io Not tainted 4.11.0-rc1-xfstests-00301-g071d9acf3d1f #633
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-20170228_101828-anatol 04/01/2014
task: ffff88003d3a8040 task.stack: ffffc90000300000
RIP: 0010:ext4_writepages+0xc89/0xf8a
RSP: 0018:ffffc90000303ca0 EFLAGS: 00010283
RAX: 0000028410000000 RBX: ffff8800383fa3b0 RCX: ffffffff812afcdc
RDX: 00000a9d00000246 RSI: ffffffff81e660e0 RDI: 0000000000000246
RBP: ffffc90000303dc0 R08: 0000000000000002 R09: 869618e8f99b4fa5
R10: 00000000852287a2 R11: 00000000a03b49f4 R12: ffff88003808e698
R13: 0000000000000000 R14: 7fffffffffffffff R15: 7fffffffffffffff
FS: 00007fd3e53094c0(0000) GS:ffff88003e400000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fd3e4c51000 CR3: 000000003d554000 CR4: 00000000003406e0
Call Trace:
? _raw_spin_unlock+0x27/0x2a
? kvm_clock_read+0x1e/0x20
do_writepages+0x23/0x2c
? do_writepages+0x23/0x2c
__filemap_fdatawrite_range+0x80/0x87
filemap_write_and_wait_range+0x67/0x8c
ext4_sync_file+0x20e/0x472
vfs_fsync_range+0x8e/0x9f
? syscall_trace_enter+0x25b/0x2d0
vfs_fsync+0x1c/0x1e
do_fsync+0x31/0x4a
SyS_fsync+0x10/0x14
do_syscall_64+0x69/0x131
entry_SYSCALL64_slow_path+0x25/0x25
We could try to be smart and keep the inline data in this case, or at
least support delayed allocation when allocating the block, but these
solutions would be more complicated and don't seem worthwhile given how
rare this case seems to be. So just fix the bug by calling
ext4_convert_inline_data() when we're asked to make a page writable, so
that any inline data gets evicted, with the block allocated immediately.
Reported-by: Nick Alcock <nick.alcock@oracle.com>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5052b069ac upstream.
Commit b685d3d65a "block: treat REQ_FUA and REQ_PREFLUSH as
synchronous" removed REQ_SYNC flag from WRITE_FUA implementation. Since
JBD2 strips REQ_FUA and REQ_FLUSH flags from submitted IO when the
filesystem is mounted with nobarrier mount option, journal superblock
writes ended up being async writes after this patch and that caused
heavy performance regression for dbench4 benchmark with high number of
processes. In my test setup with HP RAID array with non-volatile write
cache and 32 GB ram, dbench4 runs with 8 processes regressed by ~25%.
Fix the problem by making sure journal superblock writes are always
treated as synchronous since they generally block progress of the
journalling machinery and thus the whole filesystem.
Fixes: b685d3d65a
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b6eac931b9 upstream.
The driver progress routines can call cond_resched() when
a timeslice is exhausted and irqs are enabled.
If the ULP had been holding a spin lock without disabling irqs and
the post send directly called the progress routine, the cond_resched()
could yield allowing another thread from the same ULP to deadlock
on that same lock.
Correct by replacing the current hfi1_do_send() calldown with a unique
one for post send and adding an argument to hfi1_do_send() to indicate
that the send engine is running in a thread. If the routine is not
running in a thread, avoid calling cond_resched().
Fixes: Commit 831464ce4b ("IB/hfi1: Don't call cond_resched in atomic mode when sending packets")
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb7a91746a upstream.
A warning message during SRIOV multicast cleanup should have actually been
a debug level message. The condition generating the warning does no harm
and can fill the message log.
In some cases, during testing, some tests were so intense as to swamp the
message log with these warning messages, causing a stall in the console
message log output task. This stall caused an NMI to be sent to all CPUs
(so that they all dumped their stacks into the message log).
Aside from the message flood causing an NMI, the tests all passed.
Once the message flood which caused the NMI is removed (by reducing the
warning message to debug level), the NMI no longer occurs.
Sample message log (console log) output illustrating the flood and
resultant NMI (snippets with comments and modified with ... instead
of hex digits, to satisfy checkpatch.pl):
<mlx4_ib> _mlx4_ib_mcg_port_cleanup: ... WARNING: group refcount 1!!!...
*** About 4000 almost identical lines in less than one second ***
<mlx4_ib> _mlx4_ib_mcg_port_cleanup: ... WARNING: group refcount 1!!!...
INFO: rcu_sched detected stalls on CPUs/tasks: { 17} (...)
*** { 17} above indicates that CPU 17 was the one that stalled ***
sending NMI to all CPUs:
...
NMI backtrace for cpu 17
CPU: 17 PID: 45909 Comm: kworker/17:2
Hardware name: HP ProLiant DL360p Gen8, BIOS P71 09/08/2013
Workqueue: events fb_flashcursor
task: ffff880478...... ti: ffff88064e...... task.ti: ffff88064e......
RIP: 0010:[ffffffff81......] [ffffffff81......] io_serial_in+0x15/0x20
RSP: 0018:ffff88064e257cb0 EFLAGS: 00000002
RAX: 0000000000...... RBX: ffffffff81...... RCX: 0000000000......
RDX: 0000000000...... RSI: 0000000000...... RDI: ffffffff81......
RBP: ffff88064e...... R08: ffffffff81...... R09: 0000000000......
R10: 0000000000...... R11: ffff88064e...... R12: 0000000000......
R13: 0000000000...... R14: ffffffff81...... R15: 0000000000......
FS: 0000000000......(0000) GS:ffff8804af......(0000) knlGS:000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080......
CR2: 00007f2a2f...... CR3: 0000000001...... CR4: 0000000000......
DR0: 0000000000...... DR1: 0000000000...... DR2: 0000000000......
DR3: 0000000000...... DR6: 00000000ff...... DR7: 0000000000......
Stack:
ffff88064e...... ffffffff81...... ffffffff81...... 0000000000......
ffffffff81...... ffff88064e...... ffffffff81...... ffffffff81......
ffffffff81...... ffff88064e...... ffffffff81...... 0000000000......
Call Trace:
[<ffffffff813d099b>] wait_for_xmitr+0x3b/0xa0
[<ffffffff813d0b5c>] serial8250_console_putchar+0x1c/0x30
[<ffffffff813d0b40>] ? serial8250_console_write+0x140/0x140
[<ffffffff813cb5fa>] uart_console_write+0x3a/0x80
[<ffffffff813d0aae>] serial8250_console_write+0xae/0x140
[<ffffffff8107c4d1>] call_console_drivers.constprop.15+0x91/0xf0
[<ffffffff8107d6cf>] console_unlock+0x3bf/0x400
[<ffffffff813503cd>] fb_flashcursor+0x5d/0x140
[<ffffffff81355c30>] ? bit_clear+0x120/0x120
[<ffffffff8109d5fb>] process_one_work+0x17b/0x470
[<ffffffff8109e3cb>] worker_thread+0x11b/0x400
[<ffffffff8109e2b0>] ? rescuer_thread+0x400/0x400
[<ffffffff810a5aef>] kthread+0xcf/0xe0
[<ffffffff810a5a20>] ? kthread_create_on_node+0x140/0x140
[<ffffffff81645858>] ret_from_fork+0x58/0x90
[<ffffffff810a5a20>] ? kthread_create_on_node+0x140/0x140
Code: 48 89 e5 d3 e6 48 63 f6 48 03 77 10 8b 06 5d c3 66 0f 1f 44 00 00 66 66 66 6
As indicated in the stack trace above, the console output task got swamped.
Fixes: b9c5d6a643 ("IB/mlx4: Add multicast group (MCG) paravirtualization for SR-IOV")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 99e68909d5 upstream.
In mlx4_ib_add, procedure mlx4_ib_alloc_eqs is called to allocate EQs.
However, in the mlx4_ib_add error flow, procedure mlx4_ib_free_eqs is not
called to free the allocated EQs.
Fixes: e605b743f3 ("IB/mlx4: Increase the number of vectors (EQs) available for ULPs")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 771a525840 upstream.
When udev renames the netdev devices, ipoib debugfs entries does not
get renamed. As a result, if subsequent probe of ipoib device reuse the
name then creating a debugfs entry for the new device would fail.
Also, moved ipoib_create_debug_files and ipoib_delete_debug_files as part
of ipoib event handling in order to avoid any race condition between these.
Fixes: 1732b0ef3b ([IPoIB] add path record information in debugfs)
Signed-off-by: Vijay Kumar <vijay.ac.kumar@oracle.com>
Signed-off-by: Shamir Rabinovitch <shamir.rabinovitch@oracle.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b312be3d87 upstream.
The kernel commit cited below restructured ib device management
so that the device kobject is initialized in ib_alloc_device.
As part of the restructuring, the kobject is now initialized in
procedure ib_alloc_device, and is later added to the device hierarchy
in the ib_register_device call stack, in procedure
ib_device_register_sysfs (which calls device_add).
However, in the ib_device_register_sysfs error flow, if an error
occurs following the call to device_add, the cleanup procedure
device_unregister is called. This call results in the device object
being deleted -- which results in various use-after-free crashes.
The correct cleanup call is device_del -- which undoes device_add
without deleting the device object.
The device object will then (correctly) be deleted in the
ib_register_device caller's error cleanup flow, when the caller invokes
ib_dealloc_device.
Fixes: 55aeed0654 ("IB/core: Make ib_alloc_device init the kobject")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a6a5993243 upstream.
The patch 3278682123 (make skb_copy_datagram_msg() et.al. preserve
->msg_iter on error) will revert the iov buffer if copy to iter
failed, but it didn't copy any datagram if the skb_checksum_complete
error, so no need to revert any data at this place.
v2: Sabrina notice that return -EFAULT when checksum error is not correct
here, it would confuse the caller about the return value, so fix it.
Fixes: 3278682123 ("make skb_copy_datagram_msg() et.al. preserve->msg_iter on error")
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0cfef2b741 upstream.
If the mmap_sem is contented then the vfio type1 IOMMU backend will
defer locked page accounting updates to a workqueue task. This has a
few problems and depending on which side the user tries to play, they
might be over-penalized for unmaps that haven't yet been accounted or
race the workqueue to enter more mappings than they're allowed. The
original intent of this workqueue mechanism seems to be focused on
reducing latency through the ioctl, but we cannot do so at the cost
of correctness. Remove this workqueue mechanism and update the
callers to allow for failure. We can also now recheck the limit under
write lock to make sure we don't exceed it.
vfio_pin_pages_remote() also now necessarily includes an unwind path
which we can jump to directly if the consecutive page pinning finds
that we're exceeding the user's memory limits. This avoids the
current lazy approach which does accounting and mapping up to the
fault, only to return an error on the next iteration to unwind the
entire vfio_dma.
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Kirti Wankhede <kwankhede@nvidia.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 117aceb030 upstream.
When committing era metadata to disk, it doesn't always save the latest
spacemap metadata root in superblock. Due to this, metadata is getting
corrupted sometimes when reopening the device. The correct order of update
should be, pre-commit (shadows spacemap root), save the spacemap root
(newly shadowed block) to in-core superblock and then the final commit.
Signed-off-by: Somasundaram Krishnasamy <somasundaram.krishnasamy@oracle.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c82feeec9a upstream.
The message "key wipe" used to wipe real key stored in crypto layer by
rewriting it with zeroes. Since commit 28856a9 ("crypto: xts -
consolidate sanity check for keys") this no longer works in FIPS mode
for XTS.
While running in FIPS mode the crypto key part has to differ from the
tweak key.
Fixes: 28856a9 ("crypto: xts - consolidate sanity check for keys")
Signed-off-by: Ondrej Kozina <okozina@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6263b51eb3 upstream.
The CCP has the ability to perform several operations simultaneously,
but only one interrupt. When implemented as a PCI device and using
MSI-X/MSI interrupts, use a tasklet model to service interrupts. By
disabling and enabling interrupts from the CCP, coupled with the
queuing that tasklets provide, we can ensure that all events
(occurring on the device) are recognized and serviced.
This change fixes a problem wherein 2 or more busy queues can cause
notification bits to change state while a (CCP) interrupt is being
serviced, but after the queue state has been evaluated. This results
in the event being 'lost' and the queue hanging, waiting to be
serviced. Since the status bits are never fully de-asserted, the
CCP never generates another interrupt (all bits zero -> one or more
bits one), and no further CCP operations will be executed.
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b537b24e7 upstream.
The CCP has the ability to perform several operations simultaneously,
but only one interrupt. When implemented as a PCI device and using
MSI-X/MSI interrupts, use a tasklet model to service interrupts. By
disabling and enabling interrupts from the CCP, coupled with the
queuing that tasklets provide, we can ensure that all events
(occurring on the device) are recognized and serviced.
This change fixes a problem wherein 2 or more busy queues can cause
notification bits to change state while a (CCP) interrupt is being
serviced, but after the queue state has been evaluated. This results
in the event being 'lost' and the queue hanging, waiting to be
serviced. Since the status bits are never fully de-asserted, the
CCP never generates another interrupt (all bits zero -> one or more
bits one), and no further CCP operations will be executed.
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 56467cb11c upstream.
Each CCP queue can product interrupts for 4 conditions:
operation complete, queue empty, error, and queue stopped.
This driver only works with completion and error events.
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a2a251f11 upstream.
Some cipher implementations will crash if you try to use them
without calling setkey first. This patch adds a check so that
the accept(2) call will fail with -ENOKEY if setkey hasn't been
done on the socket yet.
Fixes: 400c40cf78 ("crypto: algif - add AEAD support")
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 42d5c176b7 upstream.
Driver is capable of handling only one request at a time and it stores
it in its state container struct s5p_aes_dev. This stored request must be
protected between concurrent invocations (e.g. completing current
request and scheduling new one). Combination of lock and "busy" field
is used for that purpose.
When "busy" field is true, the driver will not accept new request thus
it will not overwrite currently handled data.
However commit 28b62b1458 ("crypto: s5p-sss - Fix spinlock recursion
on LRW(AES)") moved some of the write to "busy" field out of a lock
protected critical section. This might lead to potential race between
completing current request and scheduling a new one. Effectively the
request completion might try to operate on new crypto request.
Fixes: 28b62b1458 ("crypto: s5p-sss - Fix spinlock recursion on LRW(AES)")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2859323e35 upstream.
When registering an integrity profile: if the template's interval_exp is
not 0 use it, otherwise use the ilog2() of logical block size of the
provided gendisk.
This fixes a long-standing DM linear target bug where it cannot pass
integrity data to the underlying device if its logical block size
conflicts with the underlying device's logical block size.
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c667186f1c upstream.
Our 32bit CP14/15 handling inherited some of the ARMv7 code for handling
the trapped system registers, completely missing the fact that the
fields for Rt and Rt2 are now 5 bit wide, and not 4...
Let's fix it, and provide an accessor for the most common Rt case.
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c7a5dce22 upstream.
Fix potential races in kvm_psci_vcpu_on() by taking the kvm->lock
mutex. In general, it's a bad idea to allow more than one PSCI_CPU_ON
to process the same target VCPU at the same time. One such problem
that may arise is that one PSCI_CPU_ON could be resetting the target
vcpu, which fills the entire sys_regs array with a temporary value
including the MPIDR register, while another looks up the VCPU based
on the MPIDR value, resulting in no target VCPU found. Resolves both
races found with the kvm-unit-tests/arm/psci unit test.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Reported-by: Levente Kurusa <lkurusa@redhat.com>
Suggested-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 28bf288879 upstream.
If we already entered/are about to enter SMM, don't allow switching to
INIT/SIPI_RECEIVED, otherwise the next call to kvm_apic_accept_events()
will report a warning.
Same applies if we are already in MP state INIT_RECEIVED and SMM is
requested to be turned on. Refuse to set the VCPU events in this case.
Fixes: cd7764fe9f ("KVM: x86: latch INITs while in system management mode")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9abc74a22d upstream.
This is broken since ever but sadly nobody noticed.
Recent versions of GDB set DR_CONTROL unconditionally and
UML dies due to a heap corruption. It turns out that
the PTRACE_POKEUSER was copy&pasted from i386 and assumes
that addresses are 4 bytes long.
Fix that by using 8 as address size in the calculation.
Reported-by: jie cao <cj3054@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8376efd31d upstream.
Commit 11e63f6d92 added cache flushing for unaligned writes from an
iovec, covering the first and last cache line of a >= 8 byte write and
the first cache line of a < 8 byte write. But an unaligned write of
2-7 bytes can still cover two cache lines, so make sure we flush both
in that case.
Fixes: 11e63f6d92 ("x86, pmem: fix broken __copy_user_nocache ...")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d594aa0277 upstream.
The minimum size for a new stack (512 bytes) setup for arch/x86/boot components
when the bootloader does not setup/provide a stack for the early boot components
is not "enough".
The setup code executing as part of early kernel startup code, uses the stack
beyond 512 bytes and accidentally overwrites and corrupts part of the BSS
section. This is exposed mostly in the early video setup code, where
it was corrupting BSS variables like force_x, force_y, which in-turn affected
kernel parameters such as screen_info (screen_info.orig_video_cols) and
later caused an exception/panic in console_init().
Most recent boot loaders setup the stack for early boot components, so this
stack overwriting into BSS section issue has not been exposed.
Signed-off-by: Ashish Kalra <ashish@bluestacks.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20170419152015.10011-1-ashishkalra@Ashishs-MacBook-Pro.local
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f5cccf4942 upstream.
While running a bind/unbind stress test with the dwc3 usb driver on rk3399,
the following crash was observed.
Unable to handle kernel NULL pointer dereference at virtual address 00000218
pgd = ffffffc00165f000
[00000218] *pgd=000000000174f003, *pud=000000000174f003,
*pmd=0000000001750003, *pte=00e8000001751713
Internal error: Oops: 96000005 [#1] PREEMPT SMP
Modules linked in: uinput uvcvideo videobuf2_vmalloc cmac
ipt_MASQUERADE nf_nat_masquerade_ipv4 iptable_nat nf_nat_ipv4 nf_nat rfcomm
xt_mark fuse bridge stp llc zram btusb btrtl btbcm btintel bluetooth
ip6table_filter mwifiex_pcie mwifiex cfg80211 cdc_ether usbnet r8152 mii joydev
snd_seq_midi snd_seq_midi_event snd_rawmidi snd_seq snd_seq_device ppp_async
ppp_generic slhc tun
CPU: 1 PID: 29814 Comm: kworker/1:1 Not tainted 4.4.52 #507
Hardware name: Google Kevin (DT)
Workqueue: pm pm_runtime_work
task: ffffffc0ac540000 ti: ffffffc0af4d4000 task.ti: ffffffc0af4d4000
PC is at autosuspend_check+0x74/0x174
LR is at autosuspend_check+0x70/0x174
...
Call trace:
[<ffffffc00080dcc0>] autosuspend_check+0x74/0x174
[<ffffffc000810500>] usb_runtime_idle+0x20/0x40
[<ffffffc000785ae0>] __rpm_callback+0x48/0x7c
[<ffffffc000786af0>] rpm_idle+0x1e8/0x498
[<ffffffc000787cdc>] pm_runtime_work+0x88/0xcc
[<ffffffc000249bb8>] process_one_work+0x390/0x6b8
[<ffffffc00024abcc>] worker_thread+0x480/0x610
[<ffffffc000251a80>] kthread+0x164/0x178
[<ffffffc0002045d0>] ret_from_fork+0x10/0x40
Source:
(gdb) l *0xffffffc00080dcc0
0xffffffc00080dcc0 is in autosuspend_check
(drivers/usb/core/driver.c:1778).
1773 /* We don't need to check interfaces that are
1774 * disabled for runtime PM. Either they are unbound
1775 * or else their drivers don't support autosuspend
1776 * and so they are permanently active.
1777 */
1778 if (intf->dev.power.disable_depth)
1779 continue;
1780 if (atomic_read(&intf->dev.power.usage_count) > 0)
1781 return -EBUSY;
1782 w |= intf->needs_remote_wakeup;
Code analysis shows that intf is set to NULL in usb_disable_device() prior
to setting actconfig to NULL. At the same time, usb_runtime_idle() does not
lock the usb device, and neither does any of the functions in the
traceback. This means that there is no protection against a race condition
where usb_disable_device() is removing dev->actconfig->interface[] pointers
while those are being accessed from autosuspend_check().
To solve the problem, synchronize and validate device state between
autosuspend_check() and usb_disconnect().
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d6159640d upstream.
DWC3 driver uses of_usb_get_phy_mode() which is
implemented in drivers/usb/phy/of.c and in bare minimal
configuration it might not be pulled in kernel binary.
In case of ARC or ARM this could be easily reproduced with
"allnodefconfig" +CONFIG_USB=m +CONFIG_USB_DWC3=m.
On building all ends-up with:
---------------------->8------------------
Kernel: arch/arm/boot/Image is ready
Kernel: arch/arm/boot/zImage is ready
Building modules, stage 2.
MODPOST 5 modules
ERROR: "of_usb_get_phy_mode" [drivers/usb/dwc3/dwc3.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
---------------------->8------------------
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Jeremy Kerr <jk@ozlabs.org>
Cc: linux-snps-arc@lists.infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e253d0fbc upstream.
With commit bc49d1d17d ("usb: gadget: don't couple configfs to legacy
gadgets"),it is possible to build a modular kernel with both built-in
configfs support and modular legacy gadget drivers.
But when building a kernel without modules, it is also necessary to be
able to build with configfs but without any legacy gadget driver. This
was a possible configuration when the USB_CONFIGFS was a part of the
choice options, but not anymore.
Mark the choice for legacy gadget drivers as optional restores this.
Fixes: bc49d1d17d ("usb: gadget: don't couple configfs to legacy gadgets")
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ec04a4918 upstream.
The timer expiry routine `jr3_pci_poll_dev()` checks for expiry by
checking whether the absolute value of `jiffies` (stored in local
variable `now`) is greater than the expected expiry time in jiffy units.
This will fail when `jiffies` wraps around. Also, it seems to make
sense to handle the expiry one jiffy earlier than the current test. Use
`time_after_eq()` to check for expiry.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45292be0b3 upstream.
For some reason, the driver does not consider allocation of the
subdevice private data to be a fatal error when attaching the COMEDI
device. It tests the subdevice private data pointer for validity at
certain points, but omits some crucial tests. In particular,
`jr3_pci_auto_attach()` calls `jr3_pci_alloc_spriv()` to allocate and
initialize the subdevice private data, but the same function
subsequently dereferences the pointer to access the `next_time_min` and
`next_time_max` members without checking it first. The other missing
test is in the timer expiry routine `jr3_pci_poll_dev()`, but it will
crash before it gets that far.
Fix the bug by returning `-ENOMEM` from `jr3_pci_auto_attach()` as soon
as one of the calls to `jr3_pci_alloc_spriv()` returns `NULL`. The
COMEDI core will subsequently call `jr3_pci_detach()` to clean up.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0e490657c7 upstream.
The vif->idx value is always 0 for two interfaces.
wl->vif_num = 0;
loop {
...
vif->idx = wl->vif_num;
...
wl->vif_num = i;
....
i++;
...
}
At present, vif->idx is assigned the value of wl->vif_num
at the beginning of this block and device is initialized
based on this index value.
In the next iteration, wl->vif_num is still 0 as it is only updated
later but gets assigned to vif->idx in the beginning. This causes problems
later when we try to reference a particular interface and also while
configuring the firmware.
This patch moves the assignment to vif->idx from the beginning
of the block to after wl->vif_num is updated with latest value of i.
Fixes: commit 735bb39ca3 ("staging: wilc1000: simplify vif[i]->ndev accesses")
Signed-off-by: Aditya Shankar <aditya.shankar@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b58f45c8fc upstream.
Make sure to deregister the USB driver before releasing the tty driver
to avoid use-after-free in the USB disconnect callback where the tty
devices are deregistered.
Fixes: 61e1210476 ("staging: gdm7240: adding LTE USB driver")
Cc: Won Kang <wkang77@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 12ecd24ef9 upstream.
Since 4.9 mandated USB buffers be heap allocated this causes the driver
to fail.
Since there is a wide range of buffer sizes use kmemdup to create
allocated buffer.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05c0cf88be upstream.
Since 4.9 mandated USB buffers to be heap allocated. This causes
the driver to fail.
Create buffer for USB transfers.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1944581699 upstream.
This reverts commit 833415a3e7 ("cdc-wdm: fix "out-of-sync" due to
missing notifications")
There have been several reports of wdm_read returning unexpected EIO
errors with QMI devices using the qmi_wwan driver. The reporters
confirm that reverting prevents these errors. I have been unable to
reproduce the bug myself, and have no explanation to offer either. But
reverting is the safe choice here, given that the commit was an
attempt to work around a firmware problem. Living with a firmware
problem is still better than adding driver bugs.
Reported-by: Kasper Holtze <kasper@holtze.dk>
Reported-by: Aleksander Morgado <aleksander@aleksander.es>
Reported-by: Daniele Palmas <dnlplm@gmail.com>
Fixes: 833415a3e7 ("cdc-wdm: fix "out-of-sync" due to missing notifications")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f86a96be0 upstream.
There is race condition when two USB class drivers try to call
init_usb_class at the same time and leads to crash.
code path: probe->usb_register_dev->init_usb_class
To solve this, mutex locking has been added in init_usb_class() and
destroy_usb_class().
As pointed by Alan, removed "if (usb_class)" test from destroy_usb_class()
because usb_class can never be NULL there.
Signed-off-by: Ajay Kaher <ajay.kaher@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 31c5d1922b upstream.
This development kit has an FT4232 on it with a custom USB VID/PID.
The FT4232 provides four UARTs, but only two are used. The UART 0
is used by the FlashPro5 programmer and UART 2 is connected to the
SmartFusion2 CortexM3 SoC UART port.
Note that the USB VID is registered to Actel according to Linux USB
VID database, but that was acquired by Microsemi.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 69307ccb9a upstream.
As per [1] issue #4,
"The periodic EP scheduler always tries to schedule the EPs
that have large intervals (interval equal to or greater than
128 microframes) into different microframes. So it maintains
an internal counter and increments for each large interval
EP added. When the counter is greater than 128, the scheduler
rejects the new EP. So when the hub re-enumerated 128 times,
it triggers this condition."
This results in Bandwidth error when devices with periodic
endpoints (ISO/INT) having bInterval > 7 are plugged and
unplugged several times on a TUSB73x0 XHCI host.
Workaround this issue by limiting the bInterval to 7
(i.e. interval to 6) for High-speed or faster periodic endpoints.
[1] - http://www.ti.com/lit/er/sllz076/sllz076.pdf
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 197b806ae5 upstream.
While testing modification of per se_node_acl queue_depth forcing
session reinstatement via lio_target_nacl_cmdsn_depth_store() ->
core_tpg_set_initiator_node_queue_depth(), a hung task bug triggered
when changing cmdsn_depth invoked session reinstatement while an iscsi
login was already waiting for session reinstatement to complete.
This can happen when an outstanding se_cmd descriptor is taking a
long time to complete, and session reinstatement from iscsi login
or cmdsn_depth change occurs concurrently.
To address this bug, explicitly set session_fall_back_to_erl0 = 1
when forcing session reinstatement, so session reinstatement is
not attempted if an active session is already being shutdown.
This patch has been tested with two scenarios. The first when
iscsi login is blocked waiting for iscsi session reinstatement
to complete followed by queue_depth change via configfs, and
second when queue_depth change via configfs us blocked followed
by a iscsi login driven session reinstatement.
Note this patch depends on commit d36ad77f70 to handle multiple
sessions per se_node_acl when changing cmdsn_depth, and for
pre v4.5 kernels will need to be included for stable as well.
Reported-by: Gary Guo <ghg@datera.io>
Tested-by: Gary Guo <ghg@datera.io>
Cc: Gary Guo <ghg@datera.io>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 59ac9c0781 upstream.
This patch fixes zero-length READ and WRITE handling in target/FILEIO,
which was broken a long time back by:
Since:
commit d81cb44726
Author: Paolo Bonzini <pbonzini@redhat.com>
Date: Mon Sep 17 16:36:11 2012 -0700
target: go through normal processing for all zero-length commands
which moved zero-length READ and WRITE completion out of target-core,
to doing submission into backend driver code.
To address this, go ahead and invoke target_complete_cmd() for any
non negative return value in fd_do_rw().
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: David Disseldorp <ddiss@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a71a5dc7f8 upstream.
Following the bugfix for handling non SAM_STAT_GOOD COMPARE_AND_WRITE
status during COMMIT phase in commit 9b2792c3da, the same bug exists
for the READ phase as well.
This would manifest first as a lost SCSI response, and eventual
hung task during fabric driver logout or re-login, as existing
shutdown logic waited for the COMPARE_AND_WRITE se_cmd->cmd_kref
to reach zero.
To address this bug, compare_and_write_callback() has been changed
to set post_ret = 1 and return TCM_LOGICAL_UNIT_COMMUNICATION_FAILURE
as necessary to signal failure status.
Reported-by: Bill Borsari <wgb@datera.io>
Cc: Bill Borsari <wgb@datera.io>
Tested-by: Gary Guo <ghg@datera.io>
Cc: Gary Guo <ghg@datera.io>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 69861e0a52 upstream.
When booted as pv-guest the p2m list presented by the Xen is already
mapped to virtual addresses. In dom0 case the hypervisor might make use
of 2M- or 1G-pages for this mapping. Unfortunately while being properly
aligned in virtual and machine address space, those pages might not be
aligned properly in guest physical address space.
So when trying to obtain the guest physical address of such a page
pud_pfn() and pmd_pfn() must be avoided as those will mask away guest
physical address bits not being zero in this special case.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 19b7ccf865 upstream.
Commit 25520d55cd ("block: Inline blk_integrity in struct gendisk")
introduced blk_integrity_revalidate(), which seems to assume ownership
of the stable pages flag and unilaterally clears it if no blk_integrity
profile is registered:
if (bi->profile)
disk->queue->backing_dev_info->capabilities |=
BDI_CAP_STABLE_WRITES;
else
disk->queue->backing_dev_info->capabilities &=
~BDI_CAP_STABLE_WRITES;
It's called from revalidate_disk() and rescan_partitions(), making it
impossible to enable stable pages for drivers that support partitions
and don't use blk_integrity: while the call in revalidate_disk() can be
trivially worked around (see zram, which doesn't support partitions and
hence gets away with zram_revalidate_disk()), rescan_partitions() can
be triggered from userspace at any time. This breaks rbd, where the
ceph messenger is responsible for generating/verifying CRCs.
Since blk_integrity_{un,}register() "must" be used for (un)registering
the integrity profile with the block layer, move BDI_CAP_STABLE_WRITES
setting there. This way drivers that call blk_integrity_register() and
use integrity infrastructure won't interfere with drivers that don't
but still want stable pages.
Fixes: 25520d55cd ("block: Inline blk_integrity in struct gendisk")
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Mike Snitzer <snitzer@redhat.com>
Tested-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
[idryomov@gmail.com: backport to < 4.11: bdi is embedded in queue]
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3089c1df10 upstream.
The vm fault handler relies on the fact that the VMA owns a reference
to the BO. However, once mmap_sem is released, other tasks are free to
destroy the VMA, which can lead to the BO being freed. Fix two code
paths where that can happen, both related to vm fault retries.
Found via a lock debugging warning which flagged &bo->wu_mutex as
locked while being destroyed.
Fixes: cbe12e74ee ("drm/ttm: Allow vm fault retries")
Signed-off-by: Nicolai Hähnle <nicolai.haehnle@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 84d582d236 upstream.
Recent discussion (http://marc.info/?l=xen-devel&m=149192184523741)
established that commit 72a9b18629 ("xen: Remove event channel
notification through Xen PCI platform device") (and thus commit
da72ff5bfc ("partially revert "xen: Remove event channel
notification through Xen PCI platform device"")) are unnecessary and,
in fact, prevent HVM guests from booting on Xen releases prior to 4.0
Therefore we revert both of those commits.
The summary of that discussion is below:
Here is the brief summary of the current situation:
Before the offending commit (72a9b18629):
1) INTx does not work because of the reset_watches path.
2) The reset_watches path is only taken if you have Xen > 4.0
3) The Linux Kernel by default will use vector inject if the hypervisor
support. So even INTx does not work no body running the kernel with
Xen > 4.0 would notice. Unless he explicitly disabled this feature
either in the kernel or in Xen (and this can only be disabled by
modifying the code, not user-supported way to do it).
After the offending commit (+ partial revert):
1) INTx is no longer support for HVM (only for PV guests).
2) Any HVM guest The kernel will not boot on Xen < 4.0 which does
not have vector injection support. Since the only other mode
supported is INTx which.
So based on this summary, I think before commit (72a9b18629) we were
in much better position from a user point of view.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: x86@kernel.org
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Stefano Stabellini <sstabellini@kernel.org>
Cc: Julien Grall <julien.grall@arm.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Ross Lagerwall <ross.lagerwall@citrix.com>
Cc: xen-devel@lists.xenproject.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Cc: Anthony Liguori <aliguori@amazon.com>
Cc: KarimAllah Ahmed <karahmed@amazon.de>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b9dd46188e upstream.
F2FS uses 4 bytes to represent block address. As a result, supported
size of disk is 16 TB and it equals to 16 * 1024 * 1024 / 2 segments.
Signed-off-by: Jin Qian <jinqian@google.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 425df17ce3 ]
Commit 91572088e3 ("net: use core MTU range checking in core net
infra") changed the openvswitch internal device to use the core net
infra for controlling the MTU range, but failed to actually set the
max_mtu as described in the commit message, which now defaults to
ETH_DATA_LEN.
This patch fixes this by setting max_mtu to ETH_MAX_MTU after
ether_setup() call.
Fixes: 91572088e3 ("net: use core MTU range checking in core net infra")
Signed-off-by: Jarno Rajahalme <jarno@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 922c60e89d ]
If an error is encountered in mdio_mux_init(), the error path will call
mdiobus_free(). Since mdiobus_register() has been called prior to
mdio_mux_init(), the bus->state will not be MDIOBUS_UNREGISTERED. This
causes a BUG_ON() in mdiobus_free(). To correct this issue, add an
error path for mdio_mux_init() which calls mdiobus_unregister() prior to
mdiobus_free().
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Fixes: 98bc865a1e ("net: mdio-mux: Add MDIO mux driver for iProc SoCs")
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0d0e57697f ]
The patch fixes two things at once:
1) It checks the env->allow_ptr_leaks and only prints the map address to
the log if we have the privileges to do so, otherwise it just dumps 0
as we would when kptr_restrict is enabled on %pK. Given the latter is
off by default and not every distro sets it, I don't want to rely on
this, hence the 0 by default for unprivileged.
2) Printing of ldimm64 in the verifier log is currently broken in that
we don't print the full immediate, but only the 32 bit part of the
first insn part for ldimm64. Thus, fix this up as well; it's okay to
access, since we verified all ldimm64 earlier already (including just
constants) through replace_map_fd_with_map_ptr().
Fixes: 1be7f75d16 ("bpf: enable non-root eBPF programs")
Fixes: cbd3570086 ("bpf: verifier (add ability to receive verification log)")
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 242d3a49a2 ]
For each netns (except init_net), we initialize its null entry
in 3 places:
1) The template itself, as we use kmemdup()
2) Code around dst_init_metrics() in ip6_route_net_init()
3) ip6_route_dev_notify(), which is supposed to initialize it after
loopback registers
Unfortunately the last one still happens in a wrong order because
we expect to initialize net->ipv6.ip6_null_entry->rt6i_idev to
net->loopback_dev's idev, thus we have to do that after we add
idev to loopback. However, this notifier has priority == 0 same as
ipv6_dev_notf, and ipv6_dev_notf is registered after
ip6_route_dev_notifier so it is called actually after
ip6_route_dev_notifier. This is similar to commit 2f460933f5
("ipv6: initialize route null entry in addrconf_init()") which
fixes init_net.
Fix it by picking a smaller priority for ip6_route_dev_notifier.
Also, we have to release the refcnt accordingly when unregistering
loopback_dev because device exit functions are called before subsys
exit functions.
Acked-by: David Ahern <dsahern@gmail.com>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2f460933f5 ]
Andrey reported a crash on init_net.ipv6.ip6_null_entry->rt6i_idev
since it is always NULL.
This is clearly wrong, we have code to initialize it to loopback_dev,
unfortunately the order is still not correct.
loopback_dev is registered very early during boot, we lose a chance
to re-initialize it in notifier. addrconf_init() is called after
ip6_route_init(), which means we have no chance to correct it.
Fix it by moving this initialization explicitly after
ipv6_add_dev(init_net.loopback_dev) in addrconf_init().
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 77ef033b68 ]
IFLA_PHYS_PORT_NAME is a string attribute, so terminate it with \0.
Otherwise libnl3 fails to validate netlink messages with this attribute.
"ip -detail a" assumes too that the attribute is NUL-terminated when
printing it. It often was, due to padding.
I noticed this as libvirtd failing to start on a system with sfc driver
after upgrading it to Linux 4.11, i.e. when sfc added support for
phys_port_name.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6d717134a1 ]
Andrey reported a warning triggered by the rcu code:
------------[ cut here ]------------
WARNING: CPU: 1 PID: 5911 at lib/debugobjects.c:289
debug_print_object+0x175/0x210
ODEBUG: activate active (active state 1) object type: rcu_head hint:
(null)
Modules linked in:
CPU: 1 PID: 5911 Comm: a.out Not tainted 4.11.0-rc8+ #271
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:16
dump_stack+0x192/0x22d lib/dump_stack.c:52
__warn+0x19f/0x1e0 kernel/panic.c:549
warn_slowpath_fmt+0xe0/0x120 kernel/panic.c:564
debug_print_object+0x175/0x210 lib/debugobjects.c:286
debug_object_activate+0x574/0x7e0 lib/debugobjects.c:442
debug_rcu_head_queue kernel/rcu/rcu.h:75
__call_rcu.constprop.76+0xff/0x9c0 kernel/rcu/tree.c:3229
call_rcu_sched+0x12/0x20 kernel/rcu/tree.c:3288
rt6_rcu_free net/ipv6/ip6_fib.c:158
rt6_release+0x1ea/0x290 net/ipv6/ip6_fib.c:188
fib6_del_route net/ipv6/ip6_fib.c:1461
fib6_del+0xa42/0xdc0 net/ipv6/ip6_fib.c:1500
__ip6_del_rt+0x100/0x160 net/ipv6/route.c:2174
ip6_del_rt+0x140/0x1b0 net/ipv6/route.c:2187
__ipv6_ifa_notify+0x269/0x780 net/ipv6/addrconf.c:5520
addrconf_ifdown+0xe60/0x1a20 net/ipv6/addrconf.c:3672
...
Andrey's reproducer program runs in a very tight loop, calling
'unshare -n' and then spawning 2 sets of 14 threads running random ioctl
calls. The relevant networking sequence:
1. New network namespace created via unshare -n
- ip6tnl0 device is created in down state
2. address added to ip6tnl0
- equivalent to ip -6 addr add dev ip6tnl0 fd00::bb/1
- DAD is started on the address and when it completes the host
route is inserted into the FIB
3. ip6tnl0 is brought up
- the new fixup_permanent_addr function restarts DAD on the address
4. exit namespace
- teardown / cleanup sequence starts
- once in a blue moon, lo teardown appears to happen BEFORE teardown
of ip6tunl0
+ down on 'lo' removes the host route from the FIB since the dst->dev
for the route is loobback
+ host route added to rcu callback list
* rcu callback has not run yet, so rt is NOT on the gc list so it has
NOT been marked obsolete
5. in parallel to 4. worker_thread runs addrconf_dad_completed
- DAD on the address on ip6tnl0 completes
- calls ipv6_ifa_notify which inserts the host route
All of that happens very quickly. The result is that a host route that
has been deleted from the IPv6 FIB and added to the RCU list is re-inserted
into the FIB.
The exit namespace eventually gets to cleaning up ip6tnl0 which removes the
host route from the FIB again, calls the rcu function for cleanup -- and
triggers the double rcu trace.
The root cause is duplicate DAD on the address -- steps 2 and 3. Arguably,
DAD should not be started in step 2. The interface is in the down state,
so it can not really send out requests for the address which makes starting
DAD pointless.
Since the second DAD was introduced by a recent change, seems appropriate
to use it for the Fixes tag and have the fixup function only start DAD for
addresses in the PREDAD state which occurs in addrconf_ifdown if the
address is retained.
Big thanks to Andrey for isolating a reliable reproducer for this problem.
Fixes: f1705ec197 ("net: ipv6: Make address flushing on ifdown optional")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a9f11f963a ]
Be careful when comparing tcp_time_stamp to some u32 quantity,
otherwise result can be surprising.
Fixes: 7c106d7e78 ("[TCP]: TCP Low Priority congestion control")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 332270fdc8 ]
llvm 4.0 and above generates the code like below:
....
440: (b7) r1 = 15
441: (05) goto pc+73
515: (79) r6 = *(u64 *)(r10 -152)
516: (bf) r7 = r10
517: (07) r7 += -112
518: (bf) r2 = r7
519: (0f) r2 += r1
520: (71) r1 = *(u8 *)(r8 +0)
521: (73) *(u8 *)(r2 +45) = r1
....
and the verifier complains "R2 invalid mem access 'inv'" for insn #521.
This is because verifier marks register r2 as unknown value after #519
where r2 is a stack pointer and r1 holds a constant value.
Teach verifier to recognize "stack_ptr + imm" and
"stack_ptr + reg with const val" as valid stack_ptr with new offset.
Signed-off-by: Yonghong Song <yhs@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5e0740c445 ]
Creating a geneve link with 'udpcsum' set results in a creation of link
for which UDP checksum will NOT be computed on outbound packets, as can
be seen below.
11: gen0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN
link/ether c2:85:27:b6:b4:15 brd ff:ff:ff:ff:ff:ff promiscuity 0
geneve id 200 remote 192.168.13.1 dstport 6081 noudpcsum
Similarly, creating a link with 'noudpcsum' set results in a creation
of link for which UDP checksum will be computed on outbound packets.
Fixes: 9b4437a5b8 ("geneve: Unify LWT and netdev handling.")
Signed-off-by: Girish Moodalbail <girish.moodalbail@oracle.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Acked-by: Lance Richardson <lrichard@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c21b48cc1b ]
Andrey found a way to trigger the WARN_ON_ONCE(delta < len) in
skb_try_coalesce() using syzkaller and a filter attached to a TCP
socket.
As we did recently in commit 158f323b98 ("net: adjust skb->truesize in
pskb_expand_head()") we can adjust skb->truesize from ___pskb_trim(),
via a call to skb_condense().
If all frags were freed, then skb->truesize can be recomputed.
This call can be done if skb is not yet owned, or destructor is
sock_edemux().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7162fb242c ]
Andrey found a way to trigger the WARN_ON_ONCE(delta < len) in
skb_try_coalesce() using syzkaller and a filter attached to a TCP
socket over loopback interface.
I believe one issue with looped skbs is that tcp_trim_head() can end up
producing skb with under estimated truesize.
It hardly matters for normal conditions, since packets sent over
loopback are never truncated.
Bytes trimmed from skb->head should not change skb truesize, since
skb->head is not reallocated.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5294b83086 ]
We call skb_cow_data, which is good anyway to ensure we can actually
modify the skb as such (another error from prior). Now that we have the
number of fragments required, we can safely allocate exactly that amount
of memory.
Fixes: c09440f7dc ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Acked-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c7f622120 upstream.
When any of the functions contained in NGbzero.S and GENbzero.S
vector through *bzero_from_clear_user, we may end up taking a
fault when executing one of the store alternate address space
instructions. If this happens, the exception handler does not
restore the %asi register.
This commit fixes the issue by introducing a new exception
handler that ensures the %asi register is restored when
a fault is handled.
Orabug: 25577560
Signed-off-by: Dave Aldridge <david.j.aldridge@oracle.com>
Reviewed-by: Rob Gardner <rob.gardner@oracle.com>
Reviewed-by: Babu Moger <babu.moger@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ab949d5196 upstream.
Imre Deak reported a deadlock of HD-audio driver at unbinding while
it's still in probing. Since we probe the codecs asynchronously in a
work, the codec driver probe may still be kicked off while the
controller itself is being unbound. And, azx_remove() tries to
process all pending tasks via cancel_work_sync() for fixing the other
races (see commit [0b8c82190c: ALSA: hda - Cancel probe work instead
of flush at remove]), now we may meet a bizarre deadlock:
Unbind snd_hda_intel via sysfs:
device_release_driver() ->
device_lock(snd_hda_intel) ->
azx_remove() ->
cancel_work_sync(azx_probe_work)
azx_probe_work():
codec driver probe() ->
__driver_attach() ->
device_lock(snd_hda_intel)
This deadlock is caused by the fact that both device_release_driver()
and driver_probe_device() take both the device and its parent locks at
the same time. The codec device sets the controller device as its
parent, and this lock is taken before the probe() callback is called,
while the controller remove() callback gets called also with the same
lock.
In this patch, as an ugly workaround, we unlock the controller device
temporarily during cancel_work_sync() call. The race against another
bind call should be still suppressed by the parent's device lock.
Reported-by: Imre Deak <imre.deak@intel.com>
Fixes: 0b8c82190c ("ALSA: hda - Cancel probe work instead of flush at remove")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 74e3bb7531 upstream.
The newly added function triggers a harmless warning:
drivers/staging/lustre/lustre/ptlrpc/pack_generic.c: In function 'lustre_shrink_msg':
drivers/staging/lustre/lustre/ptlrpc/pack_generic.c:472:1: error: control reaches end of non-void function [-Werror=return-type]
This probably happens because LASSERTF() contains an 'unlikely()' that
sometimes prevents gcc from analysing the control flow correctly.
Adding a return statement here seems harmless and lets us keep that
unlikely().
Fixes: 96049bd1ec ("staging: lustre: ptlrpc: embed highest XID in each request")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f3445067d upstream.
The probe function is not marked __init, but some other functions
are. This leads to a warning on older compilers (e.g. gcc-4.3),
and can cause executing freed memory when built with those
compilers:
WARNING: drivers/staging/emxx_udc/emxx_udc.o(.text+0x2d78): Section mismatch in reference from the function nbu2ss_drv_probe() to the function .init.text:nbu2ss_drv_contest_init()
This removes the annotations.
Fixes: 33aa8d45a4 ("staging: emxx_udc: Add Emma Mobile USB Gadget driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c474b8579 upstream.
Conversion macros le16_to_cpu was removed and that caused new sparse warning
sparse output:
drivers/staging/wlan-ng/p80211netdev.c:241:44: warning: incorrect type in argument 2 (different base types)
drivers/staging/wlan-ng/p80211netdev.c:241:44: expected unsigned short [unsigned] [usertype] fc
drivers/staging/wlan-ng/p80211netdev.c:241:44: got restricted __le16 [usertype] fc
Fixes: 7ad8257234 ("staging:wlan-ng:Fix sparse warning")
Signed-off-by: Igor Pylypiv <igor.pylypiv@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c13990e35 upstream.
root_squash control got accidentally moved to sysfs instead of
debugfs, and the write side of it was also broken expecting a
userspace buffer.
It contains both uid and gid values in a single file, so debugfs
is a clear place for it.
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Fixes: c948390f10 "fix inconsistencies of root squash feature"
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Reviewed-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9cc4b7cb86 upstream.
The driver was making changes to the skb_header without
ensuring it was writable (i.e. uncloned).
This patch also removes some boiler plate header size
checking/adjustment code as that is also handled by the
skb_cow_header function used to make header writable.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ed10858ead upstream.
When we have turned off RTC support, the smartpqi driver fails to build:
ERROR: "rtc_time64_to_tm" [drivers/scsi/smartpqi/smartpqi.ko] undefined!
This is easily avoided by using the generic 'struct tm' based helper rather
than the RTC specific one. While fixing this, I noticed that even though
the driver uses time64_t for storing seconds, it gets them from the
old 32-bit struct timeval. To address this, we can simplify the code
by calling ktime_get_real_seconds() directly.
Fixes: 6c223761eb ("smartpqi: initial commit of Microsemi smartpqi driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2559a1ef68 upstream.
The mac_scsi driver still gets disabled when SCSI=m. This should have
been fixed back when I enabled the tristate but I didn't see the bug.
Fixes: 6e9ae6d560 ("[PATCH] mac_scsi: Add module option to Kconfig")
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5f7c2beef8 upstream.
After a Qlogic card breaks when initializing (test case), the system can
crash in qla2xxx_eh_abort if processing anything but a scsi command type
srb.
Fixes: 1535aa75a3 ("scsi: qla2xxx: fix invalid DMA access after command aborts in PCI device remove")
Signed-off-by: Bill Kuzeja <william.kuzeja@stratus.com>
Acked-By: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd571195c9 upstream.
Without CONFIG_DEBUG_FS, we run into a link error:
drivers/scsi/qedi/qedi_iscsi.o: In function `qedi_ep_poll':
qedi_iscsi.c:(.text.qedi_ep_poll+0x134): undefined reference to `do_not_recover'
drivers/scsi/qedi/qedi_iscsi.o: In function `qedi_ep_disconnect':
qedi_iscsi.c:(.text.qedi_ep_disconnect+0x36c): undefined reference to `do_not_recover'
drivers/scsi/qedi/qedi_iscsi.o: In function `qedi_ep_connect':
qedi_iscsi.c:(.text.qedi_ep_connect+0x350): undefined reference to `do_not_recover'
drivers/scsi/qedi/qedi_fw.o: In function `qedi_tmf_work':
qedi_fw.c:(.text.qedi_tmf_work+0x3b4): undefined reference to `do_not_recover'
This defines the symbol as a constant in this case, as there is no way to
set it to anything other than zero without DEBUG_FS. In addition, I'm renaming
it to qedi_do_not_recover in order to put it into a driver specific namespace,
as "do_not_recover" is a really bad name for a kernel-wide global identifier
when it is used only in one driver.
Fixes: ace7f46ba5 ("scsi: qedi: Add QLogic FastLinQ offload iSCSI driver framework.")
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b9b22ba75 upstream.
'conn_info' is malloced in qedi_iscsi_update_conn() and should be freed
before leaving from the error handling cases, otherwise it will cause
memory leak.
Fixes: ace7f46ba5 ("scsi: qedi: Add QLogic FastLinQ offload iSCSI driver framework.")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e0f5cc650 upstream.
Otherwise the interconnect related code implementing PM runtime will
produce these errors on a failed probe:
omap_uart 48066000.serial: omap_device: omap_device_enable() called from invalid state 1
omap_uart 48066000.serial: use pm_runtime_put_sync_suspend() in driver?
Note that we now also need to check for priv in omap8250_runtime_suspend()
as it has not yet been registered if probe fails. And we need to use
pm_runtime_put_sync() to properly idle the device like we already do
in omap8250_remove().
Fixes: 61929cf016 ("tty: serial: Add 8250-core based omap driver")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a09b6a7c1 upstream.
We get the following compile errors if EXTCON is enabled as a
module but this driver is builtin:
drivers/built-in.o: In function `qcom_usb_hs_phy_power_off':
phy-qcom-usb-hs.c:(.text+0x1089): undefined reference to `extcon_unregister_notifier'
drivers/built-in.o: In function `qcom_usb_hs_phy_probe':
phy-qcom-usb-hs.c:(.text+0x11b5): undefined reference to `extcon_get_edev_by_phandle'
drivers/built-in.o: In function `qcom_usb_hs_phy_power_on':
phy-qcom-usb-hs.c:(.text+0x128e): undefined reference to `extcon_get_state'
phy-qcom-usb-hs.c:(.text+0x12a9): undefined reference to `extcon_register_notifier'
so let's mark this as needing to follow the modular status of
the extcon framework.
Fixes: 9994a33865e2427b09ba (phy: Add support for Qualcomm's USB HS phy")
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b1b23f03a upstream.
The mux_pll_src_apll_dpll_gpll_usb480m_p parent list was missing a ","
between the 3rd and 4th parent names, making them fall together and thus
lookups fail. Fix that.
Fixes: 5190c08b29 ("clk: rockchip: add clock controller for rk3036")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c0e25d883 upstream.
Make sure to detect short control-message transfers and log an error
when reading incomplete manufacturer and boot descriptors.
Note that the default all-zero descriptors will now be used after a
short transfer is detected instead of partially initialised ones.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a0467a967f upstream.
The modem-status register was read as part of device configuration at
port_probe and then again at open (and reset-resume). During open (and
reset-resume) the MSR was read before submitting the interrupt URB,
something which could lead to an MSR-change going unnoticed when it
races with open (reset-resume).
Fix this by dropping the redundant reconfiguration of the port at every
open, and only read the MSR after the interrupt URB has been submitted.
Fixes: 664d5df92e ("USB: usb-serial ch341: support for DTR/RTS/CTS")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 36356a669e upstream.
Make sure to detect short control-message transfers so that errors are
logged when reading the modem status at open.
Note that while this also avoids initialising the modem status using
uninitialised heap data, these bits could not leak to user space as they
are currently not used.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c34cb8ddf upstream.
Make sure to detect short control-message transfers when fetching
modem and line state in open and when retrieving registers.
This specifically makes sure that an errno is returned to user space on
errors in TIOCMGET instead of a zero bitmask.
Also drop the unused getdevice function which also lacked appropriate
error handling.
Fixes: f7a33e608d ("USB: serial: add quatech2 usb to serial driver")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e3e574ad85 upstream.
Make sure to detect short responses when reading the latency timer to
avoid using stale buffer data.
Note that no heap data would currently leak through sysfs as
ASYNC_LOW_LATENCY is set by default.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b631433b17 upstream.
Fix open error handling which failed to detect errors when reading the
MSR and LSR registers, something which could lead to the shadow
registers being initialised from errnos.
Note that calling the generic close implementation is sufficient in the
error paths as the interrupt urb has not yet been submitted and the
register updates have not been made.
Fixes: f4c1e8d597 ("USB: ark3116: Make existing functions 16450-aware
and add close and release functions.")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 39712e8bfa upstream.
Make sure to detect and return an error on zero-length control-message
transfers when reading from the device.
This addresses a potential failure to detect an empty transmit buffer
during close.
Also remove a redundant check for short transfer when sending a command.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e4457d9798 upstream.
Use a dedicated buffer for the DMA transfer and make sure to detect
short transfers to avoid parsing a corrupt descriptor.
Fixes: 6e8cf7751f ("USB: add EPIC support to the io_edgeport driver")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1eac5c244f upstream.
Make sure to detect short control-message transfers rather than continue
with zero-initialised data when retrieving modem status and during
device initialisation.
Fixes: 52af954599 ("USB: add USB serial ssu100 driver")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b0aed2b16 upstream.
Make sure the received data has the required headers before parsing it.
Also drop the redundant urb-status check, which has already been handled
by the caller.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a89b94b533 upstream.
We're currently emulating the vbus and id interrupts in the OTGSC
read API, but we also need to make sure that if we're handling
the events with extcon that we don't enable the interrupts for
those events in the hardware. Therefore, properly emulate this
register if we're using extcon, but don't enable the interrupts.
This allows me to get my cable connect/disconnect working
properly without getting spurious interrupts on my device that
uses an extcon for these two events.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Ivan T. Ivanov" <iivanov.xz@gmail.com>
Fixes: 3ecb3e09b0 ("usb: chipidea: Use extcon framework for VBUS and ID detect")
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f60f8ccd54 upstream.
With the id and vbus detection done via extcon we need to make
sure we poll the status of OTGSC properly by considering what the
extcon is saying, and not just what the register is saying. Let's
move this hw_wait_reg() function to the only place it's used and
simplify it for polling the OTGSC register. Then we can make
certain we only use the hw_read_otgsc() API to read OTGSC, which
will make sure we properly handle extcon events.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Ivan T. Ivanov" <iivanov.xz@gmail.com>
Fixes: 3ecb3e09b0 ("usb: chipidea: Use extcon framework for VBUS and ID detect")
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 68bd6fc3cf upstream.
Returning from for_each_available_child_of_node() loop requires cleaning
up node refcount. Error paths lacked it so for example in case of
deferred probe, the refcount of phy node was left increased.
Fixes: 6d40500ac9 ("usb: ehci/ohci-exynos: Fix of_node_put() for child when getting PHYs")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f6026b1dc upstream.
Returning from for_each_available_child_of_node() loop requires cleaning
up node refcount. Error paths lacked it so for example in case of
deferred probe, the refcount of phy node was left increased.
Fixes: 6d40500ac9 ("usb: ehci/ohci-exynos: Fix of_node_put() for child when getting PHYs")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d3fe81d2cc upstream.
ulseep_range() uses hrtimers and provides no advantage over msleep()
for larger delays. Fix up the 100ms delays here passing the adjusted "min"
value to msleep(). This helps reduce the load on the hrtimer subsystem.
Link: http://lkml.org/lkml/2017/1/11/377
Fixes: commit 2938fc63e0 ("usb: dwc2: Properly account for the force mode delays")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ab007cc94f upstream.
The PML feature is not exposed to guests so we should not be forwarding
the vmexit either.
This commit fixes BSOD 0x20001 (HYPERVISOR_ERROR) when running Hyper-V
enabled Windows Server 2016 in L1 on hardware that supports PML.
Fixes: 843e433057 ("KVM: VMX: Add PML support in VMX")
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1fb883bb82 upstream.
L2 was running with uninitialized PML fields which led to incomplete
dirty bitmap logging. This manifested as all kinds of subtle erratic
behavior of the nested guest.
Fixes: 843e433057 ("KVM: VMX: Add PML support in VMX")
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3deda5e50c upstream.
If the target vcpu for kvmppc_fast_vcpu_kick_hv() is not running on
any CPU, then we will have vcpu->arch.thread_cpu == -1, and as it
happens, kvmppc_fast_vcpu_kick_hv will call kvmppc_ipi_thread with
-1 as the cpu argument. Although this is not meaningful, in the past,
before commit 1704a81cce ("KVM: PPC: Book3S HV: Use msgsnd for IPIs
to other cores on POWER9", 2016-11-18), it was harmless because CPU
-1 is not in the same core as any real CPU thread. On a POWER9,
however, we don't do the "same core" check, so we were trying to
do a msgsnd to thread -1, which is invalid. To avoid this, we add
a check to see that vcpu->arch.thread_cpu is >= 0 before calling
kvmppc_ipi_thread() with it. Since vcpu->arch.thread_vcpu can change
asynchronously, we use READ_ONCE to ensure that the value we check is
the same value that we use as the argument to kvmppc_ipi_thread().
Fixes: 1704a81cce ("KVM: PPC: Book3S HV: Use msgsnd for IPIs to other cores on POWER9")
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 75013fb16f upstream.
Fix to the exception table entry check by using probed address
instead of the address of copied instruction.
This bug may cause unexpected kernel panic if user probe an address
where an exception can happen which should be fixup by __ex_table
(e.g. copy_from_user.)
Unless user puts a kprobe on such address, this doesn't
cause any problem.
This bug has been introduced years ago, by commit:
464846888d ("x86/kprobes: Fix a bug which can modify kernel code permanently").
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 464846888d ("x86/kprobes: Fix a bug which can modify kernel code permanently")
Link: http://lkml.kernel.org/r/148829899399.28855.12581062400757221722.stgit@devbox
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f24ecff01 upstream.
pmc_core_mtpmc_link_status() an pmc_core_check_read_lock_bit() use
test_bit() on local 32-bit variable. This causes out-of-bounds
access since test_bit() expects object at least of 'unsigned long' size:
BUG: KASAN: stack-out-of-bounds in pmc_core_probe+0x3aa/0x3b0
Call Trace:
__asan_report_load_n_noabort+0x5c/0x80
pmc_core_probe+0x3aa/0x3b0
local_pci_probe+0xf9/0x1e0
pci_device_probe+0x27b/0x350
driver_probe_device+0x419/0x830
__driver_attach+0x15f/0x1d0
bus_for_each_dev+0x129/0x1d0
driver_attach+0x42/0x70
bus_add_driver+0x385/0x690
driver_register+0x1a9/0x3d0
__pci_register_driver+0x1a2/0x290
intel_pmc_core_driver_init+0x19/0x1b
do_one_initcall+0x12e/0x280
kernel_init_freeable+0x57c/0x623
kernel_init+0x13/0x140
ret_from_fork+0x2e/0x40
Fix this by open coding bit test. While at it, also refactor this code
a little bit.
Fixes: 173943b3da ("platform/x86: intel_pmc_core: ModPhy core lanes pg status")
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
[andy: reverted not related changes, used BIT() macro]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 251fe09f13 upstream.
This is a static analysis fix. The warning is:
drivers/net/wireless/intel/iwlwifi/mvm/fw-dbg.c:912 iwl_mvm_fw_dbg_collect()
warn: integer overflows 'sizeof(*desc) + len'
I guess this code is supposed to take a NUL character, but if we write
zero bytes then it tries to write -1 characters and crashes.
Fixes: c91b865cb1 ("iwlwifi: mvm: support description for user triggered fw dbg collection")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4b70f07686 upstream.
When driver needs to access the contents of a streaming DMA buffer
without unmapping it it should call dma_sync_single_for_cpu().
Once the call has been made, the CPU "owns" the DMA buffer and can
work with it as needed.
Before the device accesses the buffer, however, ownership should be
transferred back to it with dma_sync_single_for_device().
Both calls weren't performed by the driver, resulting with odd paging
errors on some platforms. Fix it.
Fixes: a6c4fb4441 ("iwlwifi: mvm: Add FW paging mechanism for the UMAC on PCI")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c56108b58a upstream.
In DQA mode, first_agg_queue is initialized to
IWL_MVM_DQA_MIN_DATA_QUEUE. This causes two bugs in the tx response
flow:
1. When TX fails, we set IEEE80211_TX_STAT_AMPDU_NO_BACK regardless
if we actually have aggregation open on the queue. This causes
mac80211 to send a BAR frame even though there is no aggregation
open.
Fix that by simply checking the AMPDU flag that is set on by
mac80211 for AMPDU packets.
2. When reclaiming frames in aggregation mode, we reclaim based on
scheduler ssn and not the SN.
The reason is that scheduler ssn may be ahead of SN due to a hole
in the BA window that was filled.
However, if we have aggregations open on IWL_MVM_DQA_BSS_CLIENT_QUEUE
the reclaim flow will still go to the code of non-aggregation
instead of the aggregation code since IWL_MVM_DQA_BSS_CLIENT_QUEUE
is smaller than IWL_MVM_DQA_MIN_DATA_QUEUE, although it is a valid
aggregation queue.
Fix that by always using the aggregation reclaim code by default in
DQA mode (currently it is implicitly used by default for all queues
except the reserved BSS queue).
Fixes: cf961e1662 ("iwlwifi: mvm: support dqa-mode agg on non-shared queue")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 94c3e614df upstream.
In DQA mode the check whether to decrement the pending frames
counter relies on the tid status and not on the txq id.
This may result in an inconsistent state of the pending frames
counter in case frame is queued on a non aggregation queue but
with this TID, and will be followed by a failure to remove the
station and later on SYSASSERT 0x3421 when trying to remove the
MAC.
Such frames are for example bar and qos NDPs.
Fix it by aligning the condition of incrementing the counter
with the condition of decrementing it - rely on TID state for
DQA mode.
Also, avoid internal error like this affecting station removal
for DQA mode - since we can know for sure it is an internal
error.
Fixes: cf961e1662 ("iwlwifi: mvm: support dqa-mode agg on non-shared queue")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05e5a7e58d upstream.
Instead of setting the tx_cmd length in the mvm code, which is
complicated by the fact that DQA may want to temporarily store
the SKB on the side, adjust the length in the PCIe code which
also knows about this since it's responsible for duplicating
all those headers that are account for in this code.
As the PCIe code already relies on the tx_cmd->len field, this
doesn't really introduce any new dependencies.
To make this possible we need to move the memcpy() of the TX
command until after it was updated.
This does even simplify the code though, since the PCIe code
already does a lot of manipulations to build A-MSDUs correctly
and changing the length becomes a simple operation to see how
much was added/removed, rather than predicting it.
Fixes: 24afba7690 ("iwlwifi: mvm: support bss dynamic alloc/dealloc of queues")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6574dc943f upstream.
Since offchannel activity doesn't always require a BSS, e.g. ANQP
sessions, offchannel frames should not use the BSS queue, because it
might not be initialized.
Use the auxilary queue instead
Fixes: e3118ad74d ("iwlwifi: mvm: support tdls in dqa mode")
Signed-off-by: Beni Lev <beni.lev@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5351f9ab25 upstream.
When NSSN is behind the reorder buffer due to timeout
the reorder timer isn't getting re-armed until NSSN
catches up. Fix it.
Fixes: 0690405fef ("iwlwifi: mvm: add reorder timeout per frame")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c6262b754 upstream.
Our 9000 device supports 64 bit DMA address for RX only, and
not for TX.
Setting DMA mask to 64 for the whole device is erroneous - we
can do it only for a000 devices where device is capable of
both RX & TX DMA with 64 bit address space.
Fixes: 96a6497bc3 ("iwlwifi: pcie: add 9000 series multi queue rx DMA support")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ce4a03852 upstream.
shift_param is defined and set in iwl_pcie_load_cpu_sections but not
used. Fix this to avoid -Wunused-but-set-variable warning.
The code using it turned into dead code with commit dcab8ecd56
("iwlwifi: mvm: support ucode load for family_8000 B0 only") which
added a separate function iwl_pcie_load_given_ucode_8000 (then 8000b)
for IWL_DEVICE_FAMILY_8000. Commit 76f8c0e17e ("iwlwifi: pcie:
remove dead code") removed the dead code but left shift_param as is.
iwlwifi/pcie/trans.c: In function ‘iwl_pcie_load_cpu_sections’:
iwlwifi/pcie/trans.c:871:6: warning: variable ‘shift_param’ set but not used [-Wunused-but-set-variable]
Fixes: dcab8ecd56 ("iwlwifi: mvm: support ucode load for family_8000 B0 only")
Fixes: 76f8c0e17e ("iwlwifi: pcie: remove dead code")
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Cc: Sara Sharon <sara.sharon@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Liad Kaufman <liad.kaufman@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[removed some unnecessary braces]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd05a5bd6b upstream.
We don't really need clear the skb's status area nor store the
dev_cmd into it until we really commit to the frame by handing
it to the transport - defer those operations until just before
we do that.
This doesn't entirely fix the bug with frames not getting sent
out after having been deferred due to DQA, because it doesn't
restore the info->driver_data[0] place that was already set to
zero (or another value) by the A-MSDU logic.
Fixes: 24afba7690 ("iwlwifi: mvm: support bss dynamic alloc/dealloc of queues")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bac453ab37 upstream.
For unified images, we shouldn't restart the HW if suspend fails. The
only reason for restarting the HW with non-unified images is to go
back to the D0 image.
Fixes: 23ae61282b ("iwlwifi: mvm: Do not switch to D3 image on suspend")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d8320d75b5 upstream.
IWL6000G2B_UCODE_API_MAX is not defined. ucode_api_max of
IWL_DEVICE_6030 uses IWL6000G2_UCODE_API_MAX. Use this also for
MODULE_FIRMWARE.
Fixes: 9d9b21d1b6 ("iwlwifi: remove IWL_*_UCODE_API_OK")
Signed-off-by: Jürg Billeter <j@bitron.ch>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ba1c7e45ec upstream.
The mwifiex_dbg() log handler utilizes the struct device in
adapter->dev. Without it, it decides not to print anything.
As of commit 2e02b58142 ("mwifiex: Allow mwifiex early access to device
structure"), we started assigning that pointer only after we finished
mwifiex_register() -- this effectively neuters any mwifiex_dbg() logging
done before this point.
Let's move the device assignment into mwifiex_register().
Fixes: 2e02b58142 ("mwifiex: Allow mwifiex early access to device structure")
Cc: Rajat Jain <rajatja@google.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2447e2cad7 upstream.
If we don't have an out-of-band wakeup IRQ configured through DT (as
most platforms don't), then we fall out of this function with
'irq_wakeup == 0'. Other code (e.g., mwifiex_disable_wake() and
mwifiex_enable_wake()) treats 'irq_wakeup >= 0' as a valid IRQ, and so
we end up calling {enable,disable}_irq() on IRQ 0.
That seems bad, so let's not do that.
Same problem as fixed in this patch:
https://patchwork.kernel.org/patch/9531693/
[PATCH v2 2/3] btmrvl: set irq_bt to -1 when failed to parse it
with the difference that:
(a) this one is actually a regression and
(b) this affects both device tree and non-device-tree systems
While fixing the regression, also drop the verbosity on the parse
failure, so we don't see this when a DT node is present but doesn't have
an interrupt property (this is perfectly legal):
[ 21.999000] mwifiex_pcie 0000:01:00.0: fail to parse irq_wakeup from device tree
Fixes: 853402a008 ("mwifiex: Enable WoWLAN for both sdio and pcie")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Acked-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a5b60de697 upstream.
This patch fixes the issue specific to AP. AP is started with WEP
security and external station is connected to it. Data path works
in this case. Now if AP is restarted with WPA/WPA2 security,
station is able to connect but ping fails.
Driver skips the deletion of WEP keys if interface type is AP.
Removing that redundant check resolves the issue.
Fixes: e57f1734d8 ("mwifiex: add key material v2 support")
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6183468a23 upstream.
Similar to commit fcd2042e8d ("mwifiex: printk() overflow with 32-byte
SSIDs"), we failed to account for the existence of 32-char SSIDs in our
debugfs code. Unlike in that case though, we zeroed out the containing
struct first, and I'm pretty sure we're guaranteed to have some padding
after the 'ssid.ssid' and 'ssid.ssid_len' fields (the struct is 33 bytes
long).
So, this is the difference between:
# cat /sys/kernel/debug/mwifiex/mlan0/info
...
essid="0123456789abcdef0123456789abcdef "
...
and the correct output:
# cat /sys/kernel/debug/mwifiex/mlan0/info
...
essid="0123456789abcdef0123456789abcdef"
...
Fixes: 5e6e3a92b9 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0cdefd5b54 upstream.
The CPU port of the BCM53125 is configured with RGMII (no delays) but
this should actually be RGMII with transmit delay (rgmii-txid) because
STMMAC takes care of inserting the transmitter delay. This fixes
occasional packet loss encountered.
Fixes: d7b9eaff5f ("ARM: dts: sun7i: Add BCM53125 switch nodes to the lamobo-r1 board")
Reported-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f5432f0124 upstream.
commit 50e95b6b85 ("ARM: dts: am57xx-idk: Add Industrial
output support") added the TPIC2810 device-tree node under
SPI bus instead of I2C1.
Fix it. Tested on AM572x IDK by driving on-board LEDs
connected to TPIC2810
Fixes: 50e95b6b85 ("ARM: dts: am57xx-idk: Add Industrial output support")
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 179125085b upstream.
Commit d9d9cec028 ("ARM: OMAP2+: Remove legacy data from hwmod for
omap3") dropped platform data that should no longer be used as we're
booting with device tree. It turns out that smartreflex is still
using platform data and produces the following errors during probe:
smartreflex smartreflex.0: invalid resource
smartreflex smartreflex.0: omap_sr_probe: ioremap fail
smartreflex: probe of smartreflex.0 failed with error -22
smartreflex smartreflex.1: invalid resource
smartreflex smartreflex.1: omap_sr_probe: ioremap fail
smartreflex: probe of smartreflex.1 failed with error -22
Let's fix the regression by adding back the smartreflex hwmod data.
The long term is to update the smartreflex driver to use device tree
based probing.
Fixes: d9d9cec028 ("ARM: OMAP2+: Remove legacy data from hwmod
for omap3")
Reported-by: Adam Ford <aford173@gmail.com>
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 12aff99723 upstream.
After issuing a 'reboot' command the imx6sx-udoo-neo board does not
reboot as expected and it just hangs instead.
In mainline kernel only LDO enabled mode is supported. Do not provide
arm-supply/soc-supply nodes in the device tree, so that the board operates
in LDO enabled mode and can then successfully reboot via watchdog.
Fixes: 76e691fc76 ("ARM: dts: imx6sx: Add UDOO Neo support")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit acfa28b364 upstream.
The libgpio code pre-sets the GPIO values for the gpio-reset in the
device tree. This results in the device being reset during bringup.
To prevent this pre-setting, use the "open-source" flag in the device
tree.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Fixes: b1aaf88 ("ARM: dts: NSP: Add GPIO reboot method to bcm958625hr DTS file")
Fixes: 10baed1 ("ARM: dts: NSP: Add GPIO reboot method to bcm958625xmc DTS file")
Fixes: 088e3148 ("ARM: dts: NSP: Add new DT file for bcm958522er")
Fixes: e3227c1 ("ARM: dts: NSP: Add new DT file for bcm958525er")
Fixes: 2f8bc00 ("ARM: dts: NSP: Add new DT file for bcm958622hr")
Fixes: d454c37 ("ARM: dts: NSP: Add new DT file for bcm958623hr")
Fixes: f27eacf ("ARM: dts: NSP: Add new DT file for bcm988312hr")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67af5ebde1 upstream.
The camera_supply_dummy_device definition is shared between a780 and a910,
but only provided when the first is enabled and fails to build for a
configuration with only a910:
arch/arm/mach-pxa/ezx.c:1097:3: error: 'camera_supply_dummy_device' undeclared here (not in a function)
This moves the definition into its own section.
Fixes: 6c1b417adc ("ARM: pxa: ezx: use the new pxa_camera platform_data")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cbe99c538d upstream.
gcc gets confused about the control flow in ktd2692_parse_dt(), causing
it to warn about what seems like a potential bug:
drivers/leds/leds-ktd2692.c: In function 'ktd2692_probe':
drivers/leds/leds-ktd2692.c:244:15: error: '*((void *)&led_cfg+8)' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/leds/leds-ktd2692.c:225:7: error: 'led_cfg.flash_max_microamp' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/leds/leds-ktd2692.c:232:3: error: 'led_cfg.movie_max_microamp' may be used uninitialized in this function [-Werror=maybe-uninitialized]
The code is fine, and slightly reworking it in an equivalent way lets
gcc figure that out too, which gets rid of the warning.
Fixes: 77e7915b15 ("leds: ktd2692: Add missing of_node_put")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e92f0051c0 upstream.
The call to spi_master_put() in a3700_spi_remove() is redundant since
the master is registered using devm_spi_register_master() and no
reference hold by using spi_master_get() in a3700_spi_remove().
This is detected by Coccinelle semantic patch.
Fixes: 5762ab71eb ("spi: Add support for Armada 3700 SPI Controller")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ec663d967b upstream.
Commit cab15ce604 ("arm64: Introduce execute-only page access
permissions") allowed a valid user PTE to have the PTE_USER bit clear.
As a consequence, the pte_valid_not_user() macro in set_pte() was
replaced with pte_valid_global() under the assumption that only user
pages have the nG bit set. EFI mappings, however, also have the nG bit
set and set_pte() wrongly ignores issuing the DSB+ISB.
This patch reinstates the pte_valid_not_user() macro and adds the
PTE_UXN bit check since all kernel mappings have this bit set. For
clarity, pte_exec() is renamed to pte_user_exec() as it only checks for
the absence of PTE_UXN. Consequently, the user executable check in
set_pte_at() drops the pte_ng() test since pte_user_exec() is
sufficient.
Fixes: cab15ce604 ("arm64: Introduce execute-only page access permissions")
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 06dbf468a2 upstream.
The ipq board has these rates as 25MHz, and not 19.2 and 27. I
copy/pasted from other boards that have those rates but forgot
to fix the rates here.
Fixes: 30fc4212d5 ("arm: dts: qcom: Add more board clocks")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ba52e75718 upstream.
Reading both fault and status registers and logging any fault should
take priority over handling status register update.
Fix by moving the status handling to later in interrupt routine.
Fixes: d7bf353fd0 ("bq24190_charger: Add support for TI BQ24190 Battery Charger")
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 68abfb8015 upstream.
Caching the fault register after a single I2C read may not keep an accurate
value.
Fix by doing two reads in irq_handle_thread() and using the cached value
elsewhere. If a safety timer fault later clears itself, we apparently don't get
an interrupt (INT), however other interrupts would refresh the register cache.
From the data sheet: "When a fault occurs, the charger device sends out INT
and keeps the fault state in REG09 until the host reads the fault register.
Before the host reads REG09 and all the faults are cleared, the charger
device would not send any INT upon new faults. In order to read the
current fault status, the host has to read REG09 two times consecutively.
The 1st reads fault register status from the last read [1] and the 2nd reads
the current fault register status."
[1] presumably a typo; should be "last fault"
Fixes: d7bf353fd0 ("bq24190_charger: Add support for TI BQ24190 Battery Charger")
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2d9fee6a42 upstream.
We wrongly get uevents for bq24190-charger and bq24190-battery on every
register change.
Fix by checking the association with charger and battery before
emitting uevent(s).
Fixes: d7bf353fd0 ("bq24190_charger: Add support for TI BQ24190 Battery Charger")
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d62acc5ef0 upstream.
The device specific data is not fully initialized on
request_threaded_irq(). This may cause a crash when the IRQ handler
tries to reference them.
Fix the issue by installing IRQ handler at the end of the probe.
Fixes: d7bf353fd0 ("bq24190_charger: Add support for TI BQ24190 Battery Charger")
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 767eee362f upstream.
The interrupt signal is TRIGGER_FALLING. This is is specified in the
data sheet PIN FUNCTIONS: "The INT pin sends active low, 256us
pulse to host to report charger device status and fault."
Also the direction can be seen in the data sheet Figure 37 "BQ24190
with D+/D- Detection and USB On-The-Go (OTG)" which shows a 10k
pull-up resistor installed for the sample configurations.
Fixes: d7bf353fd0 ("bq24190_charger: Add support for TI BQ24190 Battery Charger")
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eac6f8b0c7 upstream.
Commit 38addce8b6 ("gcc-plugins: Add latent_entropy plugin") excludes
certain powerpc early boot code from the latent entropy plugin by adding
appropriate CFLAGS. It looks like this was supposed to cover
prom_init.o, but ended up saying init.o (which doesn't exist) instead.
Fix the typo.
Fixes: 38addce8b6 ("gcc-plugins: Add latent_entropy plugin")
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 496e9cb5b2 upstream.
The final paragraph of the help text is reversed. We want to enable
this option by default, and disable it if the toolchain has a working
-mprofile-kernel.
Fixes: 8c50b72a3b ("powerpc/ftrace: Add Kconfig & Make glue for mprofile-kernel")
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a05ef161cd upstream.
Currently the build breaks if CMA=n and SPAPR_TCE_IOMMU=y:
arch/powerpc/mm/mmu_context_iommu.c: In function ‘mm_iommu_get’:
arch/powerpc/mm/mmu_context_iommu.c:193:42: error: ‘MIGRATE_CMA’ undeclared (first use in this function)
if (get_pageblock_migratetype(page) == MIGRATE_CMA) {
^~~~~~~~~~~
Fix it by using the existing is_migrate_cma_page(), which evaulates to
false when CMA=n.
Fixes: 2e5bbb5461 ("KVM: PPC: Book3S HV: Migrate pinned pages out of CMA")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a7e0fb6c20 upstream.
Currently the opal_exit tracepoint usually shows the opcode as 0:
<idle>-0 [047] d.h. 635.654292: opal_entry: opcode=63
<idle>-0 [047] d.h. 635.654296: opal_exit: opcode=0 retval=0
kopald-1209 [019] d... 636.420943: opal_entry: opcode=10
kopald-1209 [019] d... 636.420959: opal_exit: opcode=0 retval=0
This is because we incorrectly load the opcode into r0 before calling
__trace_opal_exit(), whereas it expects the opcode in r3 (first function
parameter). In fact we are leaving the retval in r3, so opcode and
retval will always show the same value.
Instead load the opcode into r3, resulting in:
<idle>-0 [040] d.h. 636.618625: opal_entry: opcode=63
<idle>-0 [040] d.h. 636.618627: opal_exit: opcode=63 retval=0
Fixes: c49f63530b ("powernv: Add OPAL tracepoints")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4ab2537c42 upstream.
In commit a4b349540a ("powerpc/mm: Cleanup LPCR defines") we updated
LPCR_VRMASD wrongly as below.
-#define LPCR_VRMASD (0x1ful << (63-16))
+#define LPCR_VRMASD_SH 47
+#define LPCR_VRMASD (ASM_CONST(1) << LPCR_VRMASD_SH)
We initialize the VRMA bits in LPCR to 0x00 in kvm. Hence using a
different mask value as above while updating lpcr should not have any
impact.
This patch updates it to the correct value.
Fixes: a4b349540a ("powerpc/mm: Cleanup LPCR defines")
Reported-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Jia He <hejianet@gmail.com>
Acked-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 78a16d9fc1 upstream.
Since power9 does not support FAB_*_MATCH bits in MMCR1,
avoid these checks for power9. For this, patch factor out
code in isa207_get_constraint() to retain these checks
only for power8.
Patch also updates the comment in power9-pmu raw event
encode layout to remove FAB_*_MATCH.
Finally for power9, patch adds additional check for
threshold events when adding the thresh mask and value in
isa207_get_constraint().
fixes: 7ffd948fae ('powerpc/perf: factor out power8 pmu functions')
fixes: 18201b2042 ('powerpc/perf: power9 raw event format encoding')
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 78b4416aa2 upstream.
MMCRA[SDAR_MODE] specifices how the SDAR should be updated in
continous sampling mode. On P9 it must be set to 0b00 when
MMCRA[63] is set.
Fixes: c7c3f568be ('powerpc/perf: macros for power9 format encoding')
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f04d108029 upstream.
Power9 DD1 do not support PMU_HAS_SIER flag and sdsync in
perf_get_data_addr() defaults to MMCRA_SDSYNC which is wrong. Since
power9 MMCRA does not support SDSYNC bit, patch includes PPMU_NO_SIAR
flag to the check and set the sdsync with MMCRA_SAMPLE_ENABLE;
Fixes: 27593d72c4 ("powerpc/perf: Use MSR to report privilege level on P9 DD1")
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bdd9968d35 upstream.
val might become 7 in which case stime[7] (array of length 7) would be
accessed during the scnprintf call later and that will cause issues.
Obviously, string concatenation is not intended here so just a comma needs
to be added to fix the issue.
Fixes: 98a2766493 ("power_supply: Add new lp8788 charger driver")
Signed-off-by: Giedrius Statkevičius <giedrius.statkevicius@gmail.com>
Acked-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cfb725f6d3 upstream.
Shared descriptors for hash algorithms are small enough
for (split) keys to be inlined in all cases.
Since driver already does this, all what's left is to remove
unused ctx->key_dma.
Fixes: 045e36780f ("crypto: caam - ahash hmac support")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 87ec02e740 upstream.
In case ctx_dma dma mapping fails, ahash_unmap_ctx() tries to
dma unmap an invalid address:
map_seq_out_ptr_ctx() / ctx_map_to_sec4_sg() -> goto unmap_ctx ->
-> ahash_unmap_ctx() -> dma unmap ctx_dma
There is also possible to reach ahash_unmap_ctx() with ctx_dma
uninitialzed or to try to unmap the same address twice.
Fix these by setting ctx_dma = 0 where needed:
-initialize ctx_dma in ahash_init()
-clear ctx_dma in case of mapping error (instead of holding
the error code returned by the dma map function)
-clear ctx_dma after each unmapping
Fixes: 32686d34f8 ("crypto: caam - ensure that we clean up after an error")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d761119a9 upstream.
The error code handling is broken as any error code that has the same
bits set as TPM_RC_HASH passes. Implemented tpm2_rc_value() helper to
parse the error value from FMT0 and FMT1 error codes so that these types
of mistakes are prevented in the future.
Fixes: 5ca4c20cfd ("keys, trusted: select hash algorithm for TPM2 chips")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d66777caa5 upstream.
pwm4 is enabled if bit 2 of GPIO control register 4 is disabled,
not when it is enabled. Since the check is for the skip condition,
it is reversed. This applies to both IT8620 and IT8628.
Fixes: 36c4d98a78 ("hwmon: (it87) Add support for all pwm channels ...")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4617f564c0 upstream.
When calling a dm ioctl that doesn't process any data
(IOCTL_FLAGS_NO_PARAMS), the contents of the data field in struct
dm_ioctl are left initialized. Current code is incorrectly extending
the size of data copied back to user, causing the contents of kernel
stack to be leaked to user. Fix by only copying contents before data
and allow the functions processing the ioctl to override.
Signed-off-by: Adrian Salido <salidoa@google.com>
Reviewed-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f1c635b439 upstream.
Hyper-V host emulation of SCSI for virtual DVD device reports SCSI
version 0 (UNKNOWN) but is still capable of supporting REPORTLUN.
Without this patch, a GEN2 Linux guest on Hyper-V will not boot 4.11
successfully with virtual DVD ROM device. What happens is that the SCSI
scan process falls back to doing sequential probing by INQUIRY. But the
storvsc driver has a previous workaround that masks/blocks all errors
reports from INQUIRY (or MODE_SENSE) commands. This workaround causes
the scan to then populate a full set of bogus LUN's on the target and
then sends kernel spinning off into a death spiral doing block reads on
the non-existent LUNs.
By setting the correct blacklist flags, the target with the DVD device
is scanned with REPORTLUN and that works correctly.
Patch needs to go in current 4.11, it is safe but not necessary in older
kernels.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 38bd49064a upstream.
A signal can interrupt a SendReceive call which result in incoming
responses to the call being ignored. This is a problem for calls such as
open which results in the successful response being ignored. This
results in an open file resource on the server.
The patch looks into responses which were cancelled after being sent and
in case of successful open closes the open fids.
For this patch, the check is only done in SendReceive2()
RH-bz: 1403319
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Acked-by: Sachin Prabhu <sprabhu@redhat.com>
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 34a477e529 upstream.
On x86-32, with CONFIG_FIRMWARE and multiple CPUs, if you enable function
graph tracing and then suspend to RAM, it will triple fault and reboot when
it resumes.
The first fault happens when booting a secondary CPU:
startup_32_smp()
load_ucode_ap()
prepare_ftrace_return()
ftrace_graph_is_dead()
(accesses 'kill_ftrace_graph')
The early head_32.S code calls into load_ucode_ap(), which has an an
ftrace hook, so it calls prepare_ftrace_return(), which calls
ftrace_graph_is_dead(), which tries to access the global
'kill_ftrace_graph' variable with a virtual address, causing a fault
because the CPU is still in real mode.
The fix is to add a check in prepare_ftrace_return() to make sure it's
running in protected mode before continuing. The check makes sure the
stack pointer is a virtual kernel address. It's a bit of a hack, but
it's not very intrusive and it works well enough.
For reference, here are a few other (more difficult) ways this could
have potentially been fixed:
- Move startup_32_smp()'s call to load_ucode_ap() down to *after* paging
is enabled. (No idea what that would break.)
- Track down load_ucode_ap()'s entire callee tree and mark all the
functions 'notrace'. (Probably not realistic.)
- Pause graph tracing in ftrace_suspend_notifier_call() or bringup_cpu()
or __cpu_up(), and ensure that the pause facility can be queried from
real mode.
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: "Rafael J . Wysocki" <rjw@rjwysocki.net>
Cc: linux-acpi@vger.kernel.org
Cc: Borislav Petkov <bp@alien8.de>
Cc: Len Brown <lenb@kernel.org>
Link: http://lkml.kernel.org/r/5c1272269a580660703ed2eccf44308e790c7a98.1492123841.git.jpoimboe@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc434e056f upstream.
The setup/remove_state/instance() functions in the hotplug core code are
serialized against concurrent CPU hotplug, but unfortunately not serialized
against themself.
As a consequence a concurrent invocation of these function results in
corruption of the callback machinery because two instances try to invoke
callbacks on remote cpus at the same time. This results in missing callback
invocations and initiator threads waiting forever on the completion.
The obvious solution to replace get_cpu_online() with cpu_hotplug_begin()
is not possible because at least one callsite calls into these functions
from a get_online_cpu() locked region.
Extend the protection scope of the cpuhp_state_mutex from solely protecting
the state arrays to cover the callback invocation machinery as well.
Fixes: 5b7aa87e04 ("cpu/hotplug: Implement setup/removal interface")
Reported-and-tested-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: hpa@zytor.com
Cc: mingo@kernel.org
Cc: akpm@linux-foundation.org
Cc: torvalds@linux-foundation.org
Link: http://lkml.kernel.org/r/20170314150645.g4tdyoszlcbajmna@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b05c73bd1e upstream.
Allocate buffers on HEAP instead of STACK for local structures
that are to be sent using usb_control_msg().
Signed-off-by: Maksim Salau <maksim.salau@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4d6fa57b4d upstream.
While this may appear as a humdrum one line change, it's actually quite
important. An sk_buff stores data in three places:
1. A linear chunk of allocated memory in skb->data. This is the easiest
one to work with, but it precludes using scatterdata since the memory
must be linear.
2. The array skb_shinfo(skb)->frags, which is of maximum length
MAX_SKB_FRAGS. This is nice for scattergather, since these fragments
can point to different pages.
3. skb_shinfo(skb)->frag_list, which is a pointer to another sk_buff,
which in turn can have data in either (1) or (2).
The first two are rather easy to deal with, since they're of a fixed
maximum length, while the third one is not, since there can be
potentially limitless chains of fragments. Fortunately dealing with
frag_list is opt-in for drivers, so drivers don't actually have to deal
with this mess. For whatever reason, macsec decided it wanted pain, and
so it explicitly specified NETIF_F_FRAGLIST.
Because dealing with (1), (2), and (3) is insane, most users of sk_buff
doing any sort of crypto or paging operation calls a convenient function
called skb_to_sgvec (which happens to be recursive if (3) is in use!).
This takes a sk_buff as input, and writes into its output pointer an
array of scattergather list items. Sometimes people like to declare a
fixed size scattergather list on the stack; othertimes people like to
allocate a fixed size scattergather list on the heap. However, if you're
doing it in a fixed-size fashion, you really shouldn't be using
NETIF_F_FRAGLIST too (unless you're also ensuring the sk_buff and its
frag_list children arent't shared and then you check the number of
fragments in total required.)
Macsec specifically does this:
size += sizeof(struct scatterlist) * (MAX_SKB_FRAGS + 1);
tmp = kmalloc(size, GFP_ATOMIC);
*sg = (struct scatterlist *)(tmp + sg_offset);
...
sg_init_table(sg, MAX_SKB_FRAGS + 1);
skb_to_sgvec(skb, sg, 0, skb->len);
Specifying MAX_SKB_FRAGS + 1 is the right answer usually, but not if you're
using NETIF_F_FRAGLIST, in which case the call to skb_to_sgvec will
overflow the heap, and disaster ensues.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8179a101eb upstream.
ceph_set_acl() calls __ceph_setattr() if the setacl operation needs
to modify inode's i_mode. __ceph_setattr() updates inode's i_mode,
then calls posix_acl_chmod().
The problem is that __ceph_setattr() calls posix_acl_chmod() before
sending the setattr request. The get_acl() call in posix_acl_chmod()
can trigger a getxattr request. The reply of the getxattr request
can restore inode's i_mode to its old value. The set_acl() call in
posix_acl_chmod() sees old value of inode's i_mode, so it calls
__ceph_setattr() again.
Link: http://tracker.ceph.com/issues/19688
Reported-by: Jerry Lee <leisurelysw24@gmail.com>
Signed-off-by: "Yan, Zheng" <zyan@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Tested-by: Luis Henriques <lhenriques@suse.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 13bf9fbff0 upstream.
The NFSv2/v3 code does not systematically check whether we decode past
the end of the buffer. This generally appears to be harmless, but there
are a few places where we do arithmetic on the pointers involved and
don't account for the possibility that a length could be negative. Add
checks to catch these.
Reported-by: Tuomas Haanpää <thaan@synopsys.com>
Reported-by: Ari Kauppi <ari@synopsys.com>
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e6838a29ec upstream.
A client can append random data to the end of an NFSv2 or NFSv3 RPC call
without our complaining; we'll just stop parsing at the end of the
expected data and ignore the rest.
Encoded arguments and replies are stored together in an array of pages,
and if a call is too large it could leave inadequate space for the
reply. This is normally OK because NFS RPC's typically have either
short arguments and long replies (like READ) or long arguments and short
replies (like WRITE). But a client that sends an incorrectly long reply
can violate those assumptions. This was observed to cause crashes.
Also, several operations increment rq_next_page in the decode routine
before checking the argument size, which can leave rq_next_page pointing
well past the end of the page array, causing trouble later in
svc_free_pages.
So, following a suggestion from Neil Brown, add a central check to
enforce our expectation that no NFSv2/v3 call has both a large call and
a large reply.
As followup we may also want to rewrite the encoding routines to check
more carefully that they aren't running off the end of the page array.
We may also consider rejecting calls that have any extra garbage
appended. That would be safer, and within our rights by spec, but given
the age of our server and the NFS protocol, and the fact that we've
never enforced this before, we may need to balance that against the
possibility of breaking some oddball client.
Reported-by: Tuomas Haanpää <thaan@synopsys.com>
Reported-by: Ari Kauppi <ari@synopsys.com>
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e4cac23c5 upstream.
The FE setups of Intel SST bytcr_rt5640 and bytcr_rt5651 drivers carry
the ignore_suspend flag, and this prevents the suspend/resume working
properly while the stream is running, since SST core code has the
check of the running streams and returns -EBUSY. Drop these
superfluous flags for fixing the behavior.
Also, the bytcr_rt5640 driver lacks of nonatomic flag in some FE
definitions, which leads to the kernel Oops at suspend/resume like:
BUG: scheduling while atomic: systemd-sleep/3144/0x00000003
Call Trace:
dump_stack+0x5c/0x7a
__schedule_bug+0x55/0x70
__schedule+0x63c/0x8c0
schedule+0x3d/0x90
schedule_timeout+0x16b/0x320
? del_timer_sync+0x50/0x50
? sst_wait_timeout+0xa9/0x170 [snd_intel_sst_core]
? sst_wait_timeout+0xa9/0x170 [snd_intel_sst_core]
? remove_wait_queue+0x60/0x60
? sst_prepare_and_post_msg+0x275/0x960 [snd_intel_sst_core]
? sst_pause_stream+0x9b/0x110 [snd_intel_sst_core]
....
This patch addresses these appropriately, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c46f59e902 upstream.
arch_check_elf contains a usage of current_cpu_data that will call
smp_processor_id() with preemption enabled and therefore triggers a
"BUG: using smp_processor_id() in preemptible" warning when an fpxx
executable is loaded.
As a follow-up to commit b244614a60 ("MIPS: Avoid a BUG warning during
prctl(PR_SET_FP_MODE, ...)"), apply the same fix to arch_check_elf by
using raw_current_cpu_data instead. The rationale quoted from the previous
commit:
"It is assumed throughout the kernel that if any CPU has an FPU, then
all CPUs would have an FPU as well, so it is safe to perform the check
with preemption enabled - change the code to use raw_ variant of the
check to avoid the warning."
Fixes: 46490b5725 ("MIPS: kernel: elf: Improve the overall ABI and FPU mode checks")
Signed-off-by: James Cowgill <James.Cowgill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15951/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9d7f29cdb4 upstream.
calculate_min_delta() may incorrectly access a 4th element of buf2[]
which only has 3 elements. This may trigger undefined behaviour and has
been reported to cause strange crashes in start_kernel() sometime after
timer initialization when built with GCC 5.3, possibly due to
register/stack corruption:
sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
CPU 0 Unable to handle kernel paging request at virtual address ffffb0aa, epc == 8067daa8, ra == 8067da84
Oops[#1]:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.9.18 #51
task: 8065e3e0 task.stack: 80644000
$ 0 : 00000000 00000001 00000000 00000000
$ 4 : 8065b4d0 00000000 805d0000 00000010
$ 8 : 00000010 80321400 fffff000 812de408
$12 : 00000000 00000000 00000000 ffffffff
$16 : 00000002 ffffffff 80660000 806a666c
$20 : 806c0000 00000000 00000000 00000000
$24 : 00000000 00000010
$28 : 80644000 80645ed0 00000000 8067da84
Hi : 00000000
Lo : 00000000
epc : 8067daa8 start_kernel+0x33c/0x500
ra : 8067da84 start_kernel+0x318/0x500
Status: 11000402 KERNEL EXL
Cause : 4080040c (ExcCode 03)
BadVA : ffffb0aa
PrId : 0501992c (MIPS 1004Kc)
Modules linked in:
Process swapper/0 (pid: 0, threadinfo=80644000, task=8065e3e0, tls=00000000)
Call Trace:
[<8067daa8>] start_kernel+0x33c/0x500
Code: 24050240 0c0131f9 24849c64 <a200b0a8> 41606020 000000c0 0c1a45e6 00000000 0c1a5f44
UBSAN also detects the same issue:
================================================================
UBSAN: Undefined behaviour in arch/mips/kernel/cevt-r4k.c:85:41
load of address 80647e4c with insufficient space
for an object of type 'unsigned int'
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.9.18 #47
Call Trace:
[<80028f70>] show_stack+0x88/0xa4
[<80312654>] dump_stack+0x84/0xc0
[<8034163c>] ubsan_epilogue+0x14/0x50
[<803417d8>] __ubsan_handle_type_mismatch+0x160/0x168
[<8002dab0>] r4k_clockevent_init+0x544/0x764
[<80684d34>] time_init+0x18/0x90
[<8067fa5c>] start_kernel+0x2f0/0x500
=================================================================
buf2[] is intentionally only 3 elements so that the last element is the
median once 5 samples have been inserted, so explicitly prevent the
possibility of comparing against the 4th element rather than extending
the array.
Fixes: 1fa405552e ("MIPS: cevt-r4k: Dynamically calculate min_delta_ns")
Reported-by: Rabin Vincent <rabinv@axis.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Tested-by: Rabin Vincent <rabinv@axis.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15892/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 162b270c66 upstream.
KGDB is a kernel debug stub and it can't be used to debug userland as it
can only safely access kernel memory.
On MIPS however KGDB has always got the register state of sleeping
processes from the userland register context at the beginning of the
kernel stack. This is meaningless for kernel threads (which never enter
userland), and for user threads it prevents the user seeing what it is
doing while in the kernel:
(gdb) info threads
Id Target Id Frame
...
3 Thread 2 (kthreadd) 0x0000000000000000 in ?? ()
2 Thread 1 (init) 0x000000007705c4b4 in ?? ()
1 Thread -2 (shadowCPU0) 0xffffffff8012524c in arch_kgdb_breakpoint () at arch/mips/kernel/kgdb.c:201
Get the register state instead from the (partial) kernel register
context stored in the task's thread_struct for resume() to restore. All
threads now correctly appear to be in context_switch():
(gdb) info threads
Id Target Id Frame
...
3 Thread 2 (kthreadd) context_switch (rq=<optimized out>, cookie=..., next=<optimized out>, prev=0x0) at kernel/sched/core.c:2903
2 Thread 1 (init) context_switch (rq=<optimized out>, cookie=..., next=<optimized out>, prev=0x0) at kernel/sched/core.c:2903
1 Thread -2 (shadowCPU0) 0xffffffff8012524c in arch_kgdb_breakpoint () at arch/mips/kernel/kgdb.c:201
Call clobbered registers which aren't saved and exception registers
(BadVAddr & Cause) which can't be easily determined without stack
unwinding are reported as 0. The PC is taken from the return address,
such that the state presented matches that found immediately after
returning from resume().
Fixes: 8854700115 ("[MIPS] kgdb: add arch support for the kernel's kgdb core")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15829/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7661a8e5c upstream.
When instrumenting the SCSI layer to run into the
!blk_rq_nr_phys_segments(rq) case the following warning emitted from the
block layer:
blk_peek_request: bad return=-22
This happens because since commit fd3fc0b4d7 ("scsi: don't BUG_ON()
empty DMA transfers") we return the wrong error value from
scsi_prep_fn() back to the block layer.
[mkp: silenced checkpatch]
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Fixes: fd3fc0b4d7 scsi: don't BUG_ON() empty DMA transfers
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e7655fd4f upstream.
The snd_use_lock_sync() (thus its implementation
snd_use_lock_sync_helper()) has the 5 seconds timeout to break out of
the sync loop. It was introduced from the beginning, just to be
"safer", in terms of avoiding the stupid bugs.
However, as Ben Hutchings suggested, this timeout rather introduces a
potential leak or use-after-free that was apparently fixed by the
commit 2d7d54002e ("ALSA: seq: Fix race during FIFO resize"):
for example, snd_seq_fifo_event_in() -> snd_seq_event_dup() ->
copy_from_user() could block for a long time, and snd_use_lock_sync()
goes timeout and still leaves the cell at releasing the pool.
For fixing such a problem, we remove the break by the timeout while
still keeping the warning.
Suggested-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dfb00a5693 upstream.
An abstraction of asynchronous transaction for transmission of MIDI
messages was introduced in Linux v4.4. Each driver can utilize this
abstraction to transfer MIDI messages via fixed-length payload of
transaction to a certain unit address. Filling payload of the transaction
is done by callback. In this callback, each driver can return negative
error code, however current implementation assigns the return value to
unsigned variable.
This commit changes type of the variable to fix the bug.
Reported-by: Julia Lawall <Julia.Lawall@lip6.fr>
Fixes: 585d7cba5e ("ALSA: firewire-lib: add helper functions for asynchronous transactions to transfer MIDI messages")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d016d57fd upstream.
At a commit 6c29230e2a ("ALSA: oxfw: delayed registration of sound
card"), ALSA oxfw driver fails to handle SCS.1m/1d, due to -EBUSY at a call
of snd_card_register(). The cause is that the driver manages to register
two rawmidi instances with the same device number 0. This is a regression
introduced since kernel 4.7.
This commit fixes the regression, by fixing up device property after
discovering stream formats.
Fixes: 6c29230e2a ("ALSA: oxfw: delayed registration of sound card")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 105f5528b9 ]
In situations where an skb is paged, the transport header pointer and
tail pointer can be the same because the skb contents are in frags.
This results in ioctl(SIOCINQ/FIONREAD) incorrectly returning a
length of 0 when the length to receive is actually greater than zero.
skb->len is already correctly set in ip6_input_finish() with
pskb_pull(), so use skb->len as it always returns the correct result
for both linear and paged data.
Signed-off-by: Jamie Bainbridge <jbainbri@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c120144407 ]
Always zero out ca_priv data in tcp_assign_congestion_control() so that
ca_priv data is cleared out during socket creation.
Also always zero out ca_priv data in tcp_reinit_congestion_control() so
that when cc algorithm is changed, ca_priv data is cleared out as well.
We should still zero out ca_priv data even in TCP_CLOSE state because
user could call connect() on AF_UNSPEC to disconnect the socket and
leave it in TCP_CLOSE state and later call setsockopt() to switch cc
algorithm on this socket.
Fixes: 2b0a8c9ee ("tcp: add CDG congestion control")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 199ab00f3c ]
Andrey reported a out-of-bound access in ip6_tnl_xmit(), this
is because we use an ipv4 dst in ip6_tnl_xmit() and cast an IPv4
neigh key as an IPv6 address:
neigh = dst_neigh_lookup(skb_dst(skb),
&ipv6_hdr(skb)->daddr);
if (!neigh)
goto tx_err_link_failure;
addr6 = (struct in6_addr *)&neigh->primary_key; // <=== HERE
addr_type = ipv6_addr_type(addr6);
if (addr_type == IPV6_ADDR_ANY)
addr6 = &ipv6_hdr(skb)->daddr;
memcpy(&fl6->daddr, addr6, sizeof(fl6->daddr));
Also the network header of the skb at this point should be still IPv4
for 4in6 tunnels, we shold not just use it as IPv6 header.
This patch fixes it by checking if skb->protocol is ETH_P_IPV6: if it
is, we are safe to do the nexthop lookup using skb_dst() and
ipv6_hdr(skb)->daddr; if not (aka IPv4), we have no clue about which
dest address we can pick here, we have to rely on callers to fill it
from tunnel config, so just fall to ip6_route_output() to make the
decision.
Fixes: ea3dc9601b ("ip6_tunnel: Add support for wildcard tunnel endpoints.")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f555f34fdc ]
The Ethernet link on an interrupt driven PHY was not coming up if the Ethernet
cable was plugged before the Ethernet interface was brought up.
The patch trigger PHY state machine to update link state if PHY was requested to
do auto-negotiation and auto-negotiation complete flag already set.
During power-up cycle the PHY do auto-negotiation, generate interrupt and set
auto-negotiation complete flag. Interrupt is handled by PHY state machine but
doesn't update link state because PHY is in PHY_READY state. After some time
MAC bring up, start and request PHY to do auto-negotiation. If there are no new
settings to advertise genphy_config_aneg() doesn't start PHY auto-negotiation.
PHY continue to stay in auto-negotiation complete state and doesn't fire
interrupt. At the same time PHY state machine expect that PHY started
auto-negotiation and is waiting for interrupt from PHY and it won't get it.
Fixes: 321beec504 ("net: phy: Use interrupts when available in NOLINK state")
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Cc: stable <stable@vger.kernel.org> # v4.9+
Tested-by: Roger Quadros <rogerq@ti.com>
Tested-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8048ced9be ]
Taking down the loopback device wreaks havoc on IPv6 routing. By
extension, taking down a VRF device wreaks havoc on its table.
Dmitry and Andrey both reported heap out-of-bounds reports in the IPv6
FIB code while running syzkaller fuzzer. The root cause is a dead dst
that is on the garbage list gets reinserted into the IPv6 FIB. While on
the gc (or perhaps when it gets added to the gc list) the dst->next is
set to an IPv4 dst. A subsequent walk of the ipv6 tables causes the
out-of-bounds access.
Andrey's reproducer was the key to getting to the bottom of this.
With IPv6, host routes for an address have the dst->dev set to the
loopback device. When the 'lo' device is taken down, rt6_ifdown initiates
a walk of the fib evicting routes with the 'lo' device which means all
host routes are removed. That process moves the dst which is attached to
an inet6_ifaddr to the gc list and marks it as dead.
The recent change to keep global IPv6 addresses added a new function,
fixup_permanent_addr, that is called on admin up. That function restarts
dad for an inet6_ifaddr and when it completes the host route attached
to it is inserted into the fib. Since the route was marked dead and
moved to the gc list, re-inserting the route causes the reported
out-of-bounds accesses. If the device with the address is taken down
or the address is removed, the WARN_ON in fib6_del is triggered.
All of those faults are fixed by regenerating the host route if the
existing one has been moved to the gc list, something that can be
determined by checking if the rt6i_ref counter is 0.
Fixes: f1705ec197 ("net: ipv6: Make address flushing on ifdown optional")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f6478218e6 ]
When a parent macvlan device is destroyed we end up purging its
broadcast queue without dropping the device reference count on
the packet source device. This causes the source device to linger.
This patch drops that reference count.
Fixes: 260916dfb4 ("macvlan: Fix potential use-after free for...")
Reported-by: Joe Ghalam <Joe.Ghalam@dell.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4ef1b28694 ]
SOF_TIMESTAMPING_OPT_STATS can be enabled and disabled
while packets are collected on the error queue.
So, checking SOF_TIMESTAMPING_OPT_STATS in sk->sk_tsflags
is not enough to safely assume that the skb contains
OPT_STATS data.
Add a bit in sock_exterr_skb to indicate whether the
skb contains opt_stats data.
Fixes: 1c885808e4 ("tcp: SOF_TIMESTAMPING_OPT_STATS option for SO_TIMESTAMPING")
Reported-by: JongHwan Kim <zzoru007@gmail.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8605330aac ]
__sock_recv_timestamp can be called for both normal skbs (for
receive timestamps) and for skbs on the error queue (for transmit
timestamps).
Commit 1c885808e4
(tcp: SOF_TIMESTAMPING_OPT_STATS option for SO_TIMESTAMPING)
assumes any skb passed to __sock_recv_timestamp are from
the error queue, containing OPT_STATS in the content of the skb.
This results in accessing invalid memory or generating junk
data.
To fix this, set skb->pkt_type to PACKET_OUTGOING for packets
on the error queue. This is safe because on the receive path
on local sockets skb->pkt_type is never set to PACKET_OUTGOING.
With that, copy OPT_STATS from a packet, only if its pkt_type
is PACKET_OUTGOING.
Fixes: 1c885808e4 ("tcp: SOF_TIMESTAMPING_OPT_STATS option for SO_TIMESTAMPING")
Reported-by: JongHwan Kim <zzoru007@gmail.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5e82c9e4ed ]
Handler for ETHTOOL_GRXCLSRLALL must set info->data to the size
of the table, regardless of the amount of entries in it.
Existing code does not do that, and this breaks all usage of ethtool -N
or -n without explicit location, with this error:
rmgr: Invalid RX class rules table size: Success
Set info->data to the table size.
Tested:
ethtool -n ens8
ethtool -N ens8 flow-type ip4 src-ip 1.1.1.1 dst-ip 2.2.2.2 action 1
ethtool -N ens8 flow-type ip4 src-ip 1.1.1.1 dst-ip 2.2.2.2 action 1 loc 55
ethtool -n ens8
ethtool -N ens8 delete 1023
ethtool -N ens8 delete 55
Fixes: f913a72aa0 ("net/mlx5e: Add support to get ethtool flow rules")
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cbad8cddb6 ]
RX packet headers are meant to be contained in SKB linear part,
and chose a threshold of 128.
It turns out this is not enough, i.e. for IPv6 packet over VxLAN.
In this case, UDP/IPv4 needs 42 bytes, GENEVE header is 8 bytes,
and 86 bytes for TCP/IPv6. In total 136 bytes that is more than
current 128 bytes. In this case expand header flow is reached.
The warning in skb_try_coalesce() caused by a wrong truesize
was already fixed here:
commit 158f323b98 ("net: adjust skb->truesize in pskb_expand_head()").
Still, we prefer to totally avoid the expand header flow for performance reasons.
Tested regular TCP_STREAM with iperf for 1 and 8 streams, no degradation was found.
Fixes: 461017cb00 ("net/mlx5e: Support RX multi-packet WQE (Striding RQ)")
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c415f704c8 ]
On ConnectX5 the wqe inline mode is "none" and hence the FW
reports MLX5_CAP_INLINE_MODE_NOT_REQUIRED.
Fix our devlink callbacks to deal with that on get and set.
Also fix the tc flow parsing code not to fail anything when
inline isn't required.
Fixes: bffaa91658 ('net/mlx5: E-Switch, Add control for inline mode')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 55378a238e ]
If FW is stuck in initializing state we will skip the driver load, but
current error handling flow doesn't clean previously allocated command
interface resources.
Fixes: e3297246c2 ('net/mlx5_core: Wait for FW readiness on startup')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 557c44be91 ]
Andrey reported a fault in the IPv6 route code:
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] SMP KASAN
Modules linked in:
CPU: 1 PID: 4035 Comm: a.out Not tainted 4.11.0-rc7+ #250
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
task: ffff880069809600 task.stack: ffff880062dc8000
RIP: 0010:ip6_rt_cache_alloc+0xa6/0x560 net/ipv6/route.c:975
RSP: 0018:ffff880062dced30 EFLAGS: 00010206
RAX: dffffc0000000000 RBX: ffff8800670561c0 RCX: 0000000000000006
RDX: 0000000000000003 RSI: ffff880062dcfb28 RDI: 0000000000000018
RBP: ffff880062dced68 R08: 0000000000000001 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000000
R13: ffff880062dcfb28 R14: dffffc0000000000 R15: 0000000000000000
FS: 00007feebe37e7c0(0000) GS:ffff88006cb00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000205a0fe4 CR3: 000000006b5c9000 CR4: 00000000000006e0
Call Trace:
ip6_pol_route+0x1512/0x1f20 net/ipv6/route.c:1128
ip6_pol_route_output+0x4c/0x60 net/ipv6/route.c:1212
...
Andrey's syzkaller program passes rtmsg.rtmsg_flags with the RTF_PCPU bit
set. Flags passed to the kernel are blindly copied to the allocated
rt6_info by ip6_route_info_create making a newly inserted route appear
as though it is a per-cpu route. ip6_rt_cache_alloc sees the flag set
and expects rt->dst.from to be set - which it is not since it is not
really a per-cpu copy. The subsequent call to __ip6_dst_alloc then
generates the fault.
Fix by checking for the flag and failing with EINVAL.
Fixes: d52d3997f8 ("ipv6: Create percpu rt6_info")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 43170c4e0b ]
Commit 07b26c9454 ("gso: Support partial splitting at the frag_list
pointer") assumes that all SKBs in a frag_list (except maybe the last
one) contain the same amount of GSO payload.
This assumption is not always correct, resulting in the following
warning message in the log:
skb_segment: too many frags
For example, mlx5 driver in Striding RQ mode creates some RX SKBs with
one frag, and some with 2 frags.
After GRO, the frag_list SKBs end up having different amounts of payload.
If this frag_list SKB is then forwarded, the aforementioned assumption
is violated.
Validate the assumption, and fall back to software GSO if it not true.
Change-Id: Ia03983f4a47b6534dd987d7a2aad96d54d46d212
Fixes: 07b26c9454 ("gso: Support partial splitting at the frag_list pointer")
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ec9c4215fe ]
Commit a149e7c7ce ("ipv6: sr: add support for SRH injection through
setsockopt") introduced handling of IPV6_SRCRT_TYPE_4, but at the same
time restricted it to only IPV6_SRCRT_TYPE_0 and
IPV6_SRCRT_TYPE_4. Previously, ipv6_push_exthdr() and fl6_update_dst()
would also handle other values (ie STRICT and TYPE_2).
Restore previous source routing behavior, by handling IPV6_SRCRT_STRICT
and IPV6_SRCRT_TYPE_2 the same way as IPV6_SRCRT_TYPE_0 in
ipv6_push_exthdr() and fl6_update_dst().
Fixes: a149e7c7ce ("ipv6: sr: add support for SRH injection through setsockopt")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9d386cd9a7 ]
This patch is prompted by a static checker warning about a potential
use after free. The concern is that netif_rx_ni() can free "skb" and we
call it twice.
When I look at the commit that added this, it looks like some stray
lines were added accidentally. It doesn't make sense to me that we
would recieve the same data two times. I asked the author but never
recieved a response.
I can't test this code, but I'm pretty sure my patch is correct.
Fixes: 4b063258ab ("dp83640: Delay scheduled work.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1debdc8f9e ]
The DMA API debugging (when enabled) causes:
WARNING: CPU: 0 PID: 1445 at lib/dma-debug.c:519 add_dma_entry+0xe0/0x12c
DMA-API: exceeded 7 overlapping mappings of cacheline 0x01b2974d
to be printed after repeated initialization of the Ether device, e.g.
suspend/resume or 'ifconfig' up/down. This is because DMA buffers mapped
using dma_map_single() in sh_eth_ring_format() and sh_eth_start_xmit() are
never unmapped. Resolve this problem by unmapping the buffers when freeing
the descriptor rings; in order to do it right, we'd have to add an extra
parameter to sh_eth_txfree() (we rename this function to sh_eth_tx_free(),
while at it).
Based on the commit a47b70ea86 ("ravb: unmap descriptors when freeing
rings").
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1862d6208d ]
Syzkaller reported a use-after-free in ip_recv_error at line
info->ipi_ifindex = skb->dev->ifindex;
This function is called on dequeue from the error queue, at which
point the device pointer may no longer be valid.
Save ifindex on enqueue in __skb_complete_tx_timestamp, when the
pointer is valid or NULL. Store it in temporary storage skb->cb.
It is safe to reference skb->dev here, as called from device drivers
or dev_queue_xmit. The exception is when called from tcp_ack_tstamp;
in that case it is NULL and ifindex is set to 0 (invalid).
Do not return a pktinfo cmsg if ifindex is 0. This maintains the
current behavior of not returning a cmsg if skb->dev was NULL.
On dequeue, the ipv4 path will cast from sock_exterr_skb to
in_pktinfo. Both have ifindex as their first element, so no explicit
conversion is needed. This is by design, introduced in commit
0b922b7a82 ("net: original ingress device index in PKTINFO"). For
ipv6 ip6_datagram_support_cmsg converts to in6_pktinfo.
Fixes: 829ae9d611 ("net-timestamp: allow reading recv cmsg on errqueue with origin tstamp")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a2d6cbb067 ]
addrconf_ifdown() removes elements from the idev->addr_list without
holding the idev->lock.
If this happens while the loop in __ipv6_dev_get_saddr() is handling the
same element, that function ends up in an infinite loop:
NMI watchdog: BUG: soft lockup - CPU#1 stuck for 23s! [test:1719]
Call Trace:
ipv6_get_saddr_eval+0x13c/0x3a0
__ipv6_dev_get_saddr+0xe4/0x1f0
ipv6_dev_get_saddr+0x1b4/0x204
ip6_dst_lookup_tail+0xcc/0x27c
ip6_dst_lookup_flow+0x38/0x80
udpv6_sendmsg+0x708/0xba8
sock_sendmsg+0x18/0x30
SyS_sendto+0xb8/0xf8
syscall_common+0x34/0x58
Fixes: 6a923934c3 (Revert "ipv6: Revert optional address flusing on ifdown.")
Signed-off-by: Rabin Vincent <rabinv@axis.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 34b2789f1d ]
Now sctp doesn't check sock's state before listening on it. It could
even cause changing a sock with any state to become a listening sock
when doing sctp_listen.
This patch is to fix it by checking sock's state in sctp_listen, so
that it will listen on the sock with right state.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a8801799c6 ]
inet_rtm_getroute synthesizes a skeletal ICMP skb, which is passed to
ip_route_input when iif is given. If a multipath route is present for
the designated destination, ip_multipath_icmp_hash ends up being called,
which uses the source/destination addresses within the skb to calculate
a hash. However, those are not set in the synthetic skb, causing it to
return an arbitrary and incorrect result.
Instead, use UDP, which gets no such special treatment.
Signed-off-by: Florian Larysch <fl@n621.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e08293a4cc ]
Take a reference on the sessions returned by l2tp_session_find_nth()
(and rename it l2tp_session_get_nth() to reflect this change), so that
caller is assured that the session isn't going to disappear while
processing it.
For procfs and debugfs handlers, the session is held in the .start()
callback and dropped in .show(). Given that pppol2tp_seq_session_show()
dereferences the associated PPPoL2TP socket and that
l2tp_dfs_seq_session_show() might call pppol2tp_show(), we also need to
call the session's .ref() callback to prevent the socket from going
away from under us.
Fixes: fd558d186d ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts")
Fixes: 0ad6614048 ("l2tp: Add debugfs files for dumping l2tp debug info")
Fixes: 309795f4be ("l2tp: Add netlink control API for L2TP")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6f56f6186c ]
ovs_flow_key_update() is called when the flow key is invalid, and it is
used to update and revalidate the flow key. Commit 329f45bc4f
("openvswitch: add mac_proto field to the flow key") introduces mac_proto
field to flow key and use it to determine whether the flow key is valid.
However, the commit does not update the code path in ovs_flow_key_update()
to revalidate the flow key which may cause BUG_ON() on execute_recirc().
This patch addresses the aforementioned issue.
Fixes: 329f45bc4f ("openvswitch: add mac_proto field to the flow key")
Signed-off-by: Yi-Hung Wei <yihung.wei@gmail.com>
Acked-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8f8d28e4d6 ]
When calculating rb->frames_per_block * req->tp_block_nr the result
can overflow.
Add a check that tp_block_size * tp_block_nr <= UINT_MAX.
Since frames_per_block <= tp_block_size, the expression would
never overflow.
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e91793bb61 ]
The Rx path may grab the socket right before pppol2tp_release(), but
nothing guarantees that it will enqueue packets before
skb_queue_purge(). Therefore, the socket can be destroyed without its
queues fully purged.
Fix this by purging queues in pppol2tp_session_destruct() where we're
guaranteed nothing is still referencing the socket.
Fixes: 9e9cb6221a ("l2tp: fix userspace reception on plain L2TP sockets")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 94d7ee0baa ]
The code following l2tp_tunnel_find() expects that a new reference is
held on sk. Either sk_receive_skb() or the discard_put error path will
drop a reference from the tunnel's socket.
This issue exists in both l2tp_ip and l2tp_ip6.
Fixes: a3c18422a4 ("l2tp: hold socket before dropping lock in l2tp_ip{, 6}_recv()")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b1977682a3 ]
llvm can optimize the 'if (ptr > data_end)' checks to be in the order
slightly different than the original C code which will confuse verifier.
Like:
if (ptr + 16 > data_end)
return TC_ACT_SHOT;
// may be followed by
if (ptr + 14 > data_end)
return TC_ACT_SHOT;
while llvm can see that 'ptr' is valid for all 16 bytes,
the verifier could not.
Fix verifier logic to account for such case and add a test.
Reported-by: Huapeng Zhou <hzhou@fb.com>
Fixes: 969bf05eb3 ("bpf: direct packet access")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 28ee1b746f ]
Unfortunately too many devices (not under our control) use tcp_tw_recycle=1,
which depends on timestamps being identical of the same saddr.
Although tcp_tw_recycle got removed in net-next we can't make
such end hosts disappear so downgrade to per-host timestamp offsets.
4.10 note: original patch uses siphash (added in 4.11), since
ts_off is only used to obscure uptime (and doesn't use same secret
as isn generator) this uses jhash instead.
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Reported-by: Yvan Vanrossomme <yvan@vanrossomme.net>
Fixes: 95a22caee3 ("tcp: randomize tcp timestamp offsets for each connection")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 49d52e8108 ]
If the PHY is halted on stop, then do not set the state to PHY_UP. This
ensures the phy will be restarted later in phy_start when the machine is
started again.
Fixes: 00db8189d9 ("This patch adds a PHY Abstraction Layer to the Linux Kernel, enabling ethernet drivers to remain as ignorant as is reasonable of the connected PHY's design and operation details.")
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: Brad Mouring <brad.mouring@ni.com>
Acked-by: Xander Huff <xander.huff@ni.com>
Acked-by: Kyle Roeschley <kyle.roeschley@ni.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 48481c8fa1 ]
Dmitry posted a nice reproducer of a bug triggering in neigh_probe()
when dereferencing a NULL neigh->ops->solicit method.
This can happen for arp_direct_ops/ndisc_direct_ops and similar,
which can be used for NUD_NOARP neighbours (created when dev->header_ops
is NULL). Admin can then force changing nud_state to some other state
that would fire neigh timer.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit adfae8a5d8 ]
I encountered this bug when using /proc/kcore to examine the kernel. Plus a
coworker inquired about debugging tools. We computed pa but did
not use it during the maximum physical address bits test. Instead we used
the identity mapped virtual address which will always fail this test.
I believe the defect came in here:
[bpicco@zareason linus.git]$ git describe --contains bb4e6e85da
v3.18-rc1~87^2~4
.
Signed-off-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 956a4cd2c9 upstream.
The following warning triggers with a new unit test that stresses the
device-dax interface.
===============================
[ ERR: suspicious RCU usage. ]
4.11.0-rc4+ #1049 Tainted: G O
-------------------------------
./include/linux/rcupdate.h:521 Illegal context switch in RCU read-side critical section!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 0
2 locks held by fio/9070:
#0: (&mm->mmap_sem){++++++}, at: [<ffffffff8d0739d7>] __do_page_fault+0x167/0x4f0
#1: (rcu_read_lock){......}, at: [<ffffffffc03fbd02>] dax_dev_huge_fault+0x32/0x620 [dax]
Call Trace:
dump_stack+0x86/0xc3
lockdep_rcu_suspicious+0xd7/0x110
___might_sleep+0xac/0x250
__might_sleep+0x4a/0x80
__alloc_pages_nodemask+0x23a/0x360
alloc_pages_current+0xa1/0x1f0
pte_alloc_one+0x17/0x80
__pte_alloc+0x1e/0x120
__get_locked_pte+0x1bf/0x1d0
insert_pfn.isra.70+0x3a/0x100
? lookup_memtype+0xa6/0xd0
vm_insert_mixed+0x64/0x90
dax_dev_huge_fault+0x520/0x620 [dax]
? dax_dev_huge_fault+0x32/0x620 [dax]
dax_dev_fault+0x10/0x20 [dax]
__do_fault+0x1e/0x140
__handle_mm_fault+0x9af/0x10d0
handle_mm_fault+0x16d/0x370
? handle_mm_fault+0x47/0x370
__do_page_fault+0x28c/0x4f0
trace_do_page_fault+0x58/0x2a0
do_async_page_fault+0x1a/0xa0
async_page_fault+0x28/0x30
Inserting a page table entry may trigger an allocation while we are
holding a read lock to keep the device instance alive for the duration
of the fault. Use srcu for this keep-alive protection.
Fixes: dee4107924 ("/dev/dax, core: file operations and dax-mmap")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 29f72ce3e4 upstream.
MCA bank 3 is reserved on systems pre-Fam17h, so it didn't have a name.
However, MCA bank 3 is defined on Fam17h systems and can be accessed
using legacy MSRs. Without a name we get a stack trace on Fam17h systems
when trying to register sysfs files for bank 3 on kernels that don't
recognize Scalable MCA.
Call MCA bank 3 "decode_unit" since this is what it represents on
Fam17h. This will allow kernels without SMCA support to see this bank on
Fam17h+ and prevent the stack trace. This will not affect older systems
since this bank is reserved on them, i.e. it'll be ignored.
Tested on AMD Fam15h and Fam17h systems.
WARNING: CPU: 26 PID: 1 at lib/kobject.c:210 kobject_add_internal
kobject: (ffff88085bb256c0): attempted to be registered with empty name!
...
Call Trace:
kobject_add_internal
kobject_add
kobject_create_and_add
threshold_create_device
threshold_init_device
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: http://lkml.kernel.org/r/1490102285-3659-1-git-send-email-Yazen.Ghannam@amd.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9e1ba4f27f upstream.
If we set a kprobe on a 'stdu' instruction on powerpc64, we see a kernel
OOPS:
Bad kernel stack pointer cd93c840 at c000000000009868
Oops: Bad kernel stack pointer, sig: 6 [#1]
...
GPR00: c000001fcd93cb30 00000000cd93c840 c0000000015c5e00 00000000cd93c840
...
NIP [c000000000009868] resume_kernel+0x2c/0x58
LR [c000000000006208] program_check_common+0x108/0x180
On a 64-bit system when the user probes on a 'stdu' instruction, the kernel does
not emulate actual store in emulate_step() because it may corrupt the exception
frame. So the kernel does the actual store operation in exception return code
i.e. resume_kernel().
resume_kernel() loads the saved stack pointer from memory using lwz, which only
loads the low 32-bits of the address, causing the kernel crash.
Fix this by loading the 64-bit value instead.
Fixes: be96f63375 ("powerpc: Split out instruction analysis part of emulate_step()")
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Reviewed-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Reviewed-by: Ananth N Mavinakayanahalli <ananth@linux.vnet.ibm.com>
[mpe: Change log massage, add stable tag]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9cd9a21ce0 upstream.
In commit 6afaf8a484 ("UBI: flush wl before clearing update marker") I
managed to trigger and fix a similar bug. Now here is another version of
which I assumed it wouldn't matter back then but it turns out UBI has a
check for it and will error out like this:
|ubi0 warning: validate_vid_hdr: inconsistent used_ebs
|ubi0 error: validate_vid_hdr: inconsistent VID header at PEB 592
All you need to trigger this is? "ubiupdatevol /dev/ubi0_0 file" + a
powercut in the middle of the operation.
ubi_start_update() sets the update-marker and puts all EBs on the erase
list. After that userland can proceed to write new data while the old EB
aren't erased completely. A powercut at this point is usually not that
much of a tragedy. UBI won't give read access to the static volume
because it has the update marker. It will most likely set the corrupted
flag because it misses some EBs.
So we are all good. Unless the size of the image that has been written
differs from the old image in the magnitude of at least one EB. In that
case UBI will find two different values for `used_ebs' and refuse to
attach the image with the error message mentioned above.
So in order not to get in the situation, the patch will ensure that we
wait until everything is removed before it tries to write any data.
The alternative would be to detect such a case and remove all EBs at the
attached time after we processed the volume-table and see the
update-marker set. The patch looks bigger and I doubt it is worth it
since usually the write() will wait from time to time for a new EB since
usually there not that many spare EB that can be used.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0dc9c639e6 upstream.
The NFIT MCE handler callback (for handling media errors on NVDIMMs)
takes a mutex to add the location of a memory error to a list. But since
the notifier call chain for machine checks (x86_mce_decoder_chain) is
atomic, we get a lockdep splat like:
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:620
in_atomic(): 1, irqs_disabled(): 0, pid: 4, name: kworker/0:0
[..]
Call Trace:
dump_stack
___might_sleep
__might_sleep
mutex_lock_nested
? __lock_acquire
nfit_handle_mce
notifier_call_chain
atomic_notifier_call_chain
? atomic_notifier_call_chain
mce_gen_pool_process
Convert the notifier to a blocking one which gets to run only in process
context.
Boris: remove the notifier call in atomic context in print_mce(). For
now, let's print the MCE on the atomic path so that we can make sure
they go out and get logged at least.
Fixes: 6839a6d96f ("nfit: do an ARS scrub on hitting a latent media error")
Reported-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: x86-ml <x86@kernel.org>
Link: http://lkml.kernel.org/r/20170411224457.24777-1-vishal.l.verma@intel.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9e478066ea upstream.
There are two bugs in the follow-MAC code:
* it treats the radiotap header as the 802.11 header
(therefore it can't possibly work)
* it doesn't verify that the skb data it accesses is actually
present in the header, which is mitigated by the first point
Fix this by moving all of this out into a separate function.
This function copies the data it needs using skb_copy_bits()
to make sure it can be accessed if it's paged, and offsets
that by the possibly present vendor radiotap header.
This also makes all those conditions more readable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3018e947d7 upstream.
AP/AP_VLAN modes don't accept any real 802.11 multicast data
frames, but since they do need to accept broadcast management
frames the same is currently permitted for data frames. This
opens a security problem because such frames would be decrypted
with the GTK, and could even contain unicast L3 frames.
Since the spec says that ToDS frames must always have the BSSID
as the RA (addr1), reject any other data frames.
The problem was originally reported in "Predicting, Decrypting,
and Abusing WPA2/802.11 Group Keys" at usenix
https://www.usenix.org/conference/usenixsecurity16/technical-sessions/presentation/vanhoef
and brought to my attention by Jouni.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
--
commit 32fe905c17 upstream.
It is perfectly fine to link a tmpfile back using linkat().
Since tmpfiles are created with a link count of 0 they appear
on the orphan list, upon re-linking the inode has to be removed
from the orphan list again.
Ralph faced a filesystem corruption in combination with overlayfs
due to this bug.
Cc: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Cc: Amir Goldstein <amir73il@gmail.com>
Reported-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Tested-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Reported-by: Amir Goldstein <amir73il@gmail.com>
Fixes: 474b93704f ("ubifs: Implement O_TMPFILE")
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c3d9fda688 upstream.
Remove faulty leftover check in do_rename(), apparently introduced in a
merge that combined whiteout support changes with commit f03b8ad8d3
("fs: support RENAME_NOREPLACE for local filesystems")
Fixes: f03b8ad8d3 ("fs: support RENAME_NOREPLACE for local filesystems")
Fixes: 9e0a1fff8d ("ubifs: Implement RENAME_WHITEOUT")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9f32784535 upstream.
Currently for DDR50 card, it need tuning in default. We meet tuning fail
issue for DDR50 card and some data CRC error when DDR50 sd card works.
This is because the default pad I/O drive strength can't make sure DDR50
card work stable. So increase the pad I/O drive strength for DDR50 card,
and use pins_100mhz.
This fixes DDR50 card support for IMX since DDR50 tuning was enabled from
commit 9faac7b95e ("mmc: sdhci: enable tuning for DDR50")
Tested-and-reported-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a6db2c8603 upstream.
According to the SDIO standard interrupts are normally signalled in a
very complicated way. They require the card clock to be running and
require the controller to be paying close attention to the signals
coming from the card. This simply can't happen with the clock stopped
or with the controller in a low power mode.
To that end, we'll disable runtime_pm when we detect that an SDIO card
was inserted. This is much like with what we do with the special
"SDMMC_CLKEN_LOW_PWR" bit that dw_mmc supports.
NOTE: we specifically do this Runtime PM disabling at card init time
rather than in the enable_sdio_irq() callback. This is _different_
than how SDHCI does it. Why do we do it differently?
- Unlike SDHCI, dw_mmc uses the standard sdio_irq code in Linux (AKA
dw_mmc doesn't set MMC_CAP2_SDIO_IRQ_NOTHREAD).
- Because we use the standard sdio_irq code:
- We see a constant stream of enable_sdio_irq(0) and
enable_sdio_irq(1) calls. This is because the standard code
disables interrupts while processing and re-enables them after.
- While interrupts are disabled, there's technically a period where
we could get runtime disabled while processing interrupts.
- If we are runtime disabled while processing interrupts, we'll
reset the controller at resume time (see dw_mci_runtime_resume),
which seems like a terrible idea because we could possibly have
another interrupt pending.
To fix the above isues we'd want to put something in the standard
sdio_irq code that makes sure to call pm_runtime get/put when
interrupts are being actively being processed. That's possible to do,
but it seems like a more complicated mechanism when we really just
want the runtime pm disabled always for SDIO cards given that all the
other bits needed to get Runtime PM vs. SDIO just aren't there.
NOTE: at some point in time someone might come up with a fancy way to
do SDIO interrupts and still allow (some) amount of runtime PM.
Technically we could turn off the card clock if we used an alternate
way of signaling SDIO interrupts (and out of band interrupt is one way
to do this). We probably wouldn't actually want to fully runtime
suspend in this case though--at least not with the current
dw_mci_runtime_resume() which basically fully resets the controller at
resume time.
Fixes: e9ed8835e9 ("mmc: dw_mmc: add runtime PM callback")
Reported-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe8c470ab8 upstream.
gcc -O2 cannot always prove that the loop in acpi_power_get_inferred_state()
is enterered at least once, so it assumes that cur_state might not get
initialized:
drivers/acpi/power.c: In function 'acpi_power_get_inferred_state':
drivers/acpi/power.c:222:9: error: 'cur_state' may be used uninitialized in this function [-Werror=maybe-uninitialized]
This sets the variable to zero at the start of the loop, to ensure that
there is well-defined behavior even for an empty list. This gets rid of
the warning.
The warning first showed up when the -Os flag got removed in a bug fix
patch in linux-4.11-rc5.
I would suggest merging this addon patch on top of that bug fix to avoid
introducing a new warning in the stable kernels.
Fixes: 61b79e16c6 (ACPI: Fix incompatibility with mcount-based function graph tracing)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 704de489e0 upstream.
Temporary got a Lifebook E547 into my hands and noticed the touchpad
only works after running:
echo "1" > /sys/devices/platform/i8042/serio2/crc_enabled
Add it to the list of machines that need this workaround.
Signed-off-by: Thorsten Leemhuis <linux@leemhuis.info>
Reviewed-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8f60d1fad upstream.
On heavy paging with KSM I see guest data corruption. Turns out that
KSM will add pages to its tree, where the mapping return true for
pte_unused (or might become as such later). KSM will unmap such pages
and reinstantiate with different attributes (e.g. write protected or
special, e.g. in replace_page or write_protect_page)). This uncovered
a bug in our pagetable handling: We must remove the unused flag as
soon as an entry becomes present again.
Signed-of-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce69e2fea0 upstream.
When deploying runtime PM, it's quite verbose to print the
log of ios setting. Also it's useless to print it from system
PM as it should be the same with booting time. We also have
sysfs to get all these information from ios attribute, so let's
skip this print from PM context.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a0918f1ce6 upstream.
STATUS_BAD_NETWORK_NAME can be received during node failover,
causing the flag to be set and making the reconnect thread
always unsuccessful, thereafter.
Once the only place where it is set is removed, the remaining
bits are rendered moot.
Removing it does not prevent "mount" from failing when a non
existent share is passed.
What happens when the share really ceases to exist while the
share is mounted is undefined now as much as it was before.
Signed-off-by: Germano Percossi <germano.percossi@citrix.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 62a6cfddcc upstream.
commit 4fcd1813e6 ("Fix reconnect to not defer smb3 session reconnect
long after socket reconnect") added support for Negotiate requests to
be initiated by echo calls.
To avoid delays in calling echo after a reconnect, I added the patch
introduced by the commit b8c600120f ("Call echo service immediately
after socket reconnect").
This has however caused a regression with cifs shares which do not have
support for echo calls to trigger Negotiate requests. On connections
which need to call Negotiation, the echo calls trigger an error which
triggers a reconnect which in turn triggers another echo call. This
results in a loop which is only broken when an operation is performed on
the cifs share. For an idle share, it can DOS a server.
The patch uses the smb_operation can_echo() for cifs so that it is
called only if connection has been already been setup.
kernel bz: 194531
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Tested-by: Jonathan Liu <net147@gmail.com>
Acked-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc280fe871 upstream.
Commit 6afcf8ef0c ("mm, compaction: fix NR_ISOLATED_* stats for pfn
based migration") moved the dec_node_page_state() call (along with the
page_is_file_cache() call) to after putback_lru_page().
But page_is_file_cache() can change after putback_lru_page() is called,
so it should be called before putback_lru_page(), as it was before that
patch, to prevent NR_ISOLATE_* stats from going negative.
Without this fix, non-CONFIG_SMP kernels end up hanging in the
while(too_many_isolated()) { congestion_wait() } loop in
shrink_active_list() due to the negative stats.
Mem-Info:
active_anon:32567 inactive_anon:121 isolated_anon:1
active_file:6066 inactive_file:6639 isolated_file:4294967295
^^^^^^^^^^
unevictable:0 dirty:115 writeback:0 unstable:0
slab_reclaimable:2086 slab_unreclaimable:3167
mapped:3398 shmem:18366 pagetables:1145 bounce:0
free:1798 free_pcp:13 free_cma:0
Fixes: 6afcf8ef0c ("mm, compaction: fix NR_ISOLATED_* stats for pfn based migration")
Link: http://lkml.kernel.org/r/1492683865-27549-1-git-send-email-rabin.vincent@axis.com
Signed-off-by: Rabin Vincent <rabinv@axis.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Ming Ling <ming.ling@spreadtrum.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 78f7a45dac upstream.
I noticed that reading the snapshot file when it is empty no longer gives a
status. It suppose to show the status of the snapshot buffer as well as how
to allocate and use it. For example:
># cat snapshot
# tracer: nop
#
#
# * Snapshot is allocated *
#
# Snapshot commands:
# echo 0 > snapshot : Clears and frees snapshot buffer
# echo 1 > snapshot : Allocates snapshot buffer, if not already allocated.
# Takes a snapshot of the main buffer.
# echo 2 > snapshot : Clears snapshot buffer (but does not allocate or free)
# (Doesn't have to be '2' works with any number that
# is not a '0' or '1')
But instead it just showed an empty buffer:
># cat snapshot
# tracer: nop
#
# entries-in-buffer/entries-written: 0/0 #P:4
#
# _-----=> irqs-off
# / _----=> need-resched
# | / _---=> hardirq/softirq
# || / _--=> preempt-depth
# ||| / delay
# TASK-PID CPU# |||| TIMESTAMP FUNCTION
# | | | |||| | |
What happened was that it was using the ring_buffer_iter_empty() function to
see if it was empty, and if it was, it showed the status. But that function
was returning false when it was empty. The reason was that the iter header
page was on the reader page, and the reader page was empty, but so was the
buffer itself. The check only tested to see if the iter was on the commit
page, but the commit page was no longer pointing to the reader page, but as
all pages were empty, the buffer is also.
Fixes: 651e22f270 ("ring-buffer: Always reset iterator to reader page")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 286f3f4787 upstream.
Because HID_DG_TOOLSERIALNUMBER doesn't first cast the value recieved from HID
to an unsigned type, sign-extension rules can cause the value of
wacom_wac->serial[0] to inadvertently wind up with all 32 of its highest bits
set if the highest bit of "value" was set.
This can cause problems for Tablet PC devices which use AES sensors and the
xf86-input-wacom userspace driver. It is not uncommon for AES sensors to send a
serial number of '0' while the pen is entering or leaving proximity. The
xf86-input-wacom driver ignores events with a serial number of '0' since it
cannot match them up to an in-use tool. To ensure the xf86-input-wacom driver
does not ignore the final out-of-proximity event, the kernel does not send
MSC_SERIAL events when the value of wacom_wac->serial[0] is '0'. If the highest
bit of HID_DG_TOOLSERIALNUMBER is set by an in-prox pen which later leaves
proximity and sends a '0' for HID_DG_TOOLSERIALNUMBER, then only the lowest 32
bits of wacom_wac->serial[0] are actually cleared, causing the kernel to send
an MSC_SERIAL event. Since the 'input_event' function takes an 'int' as
argument, only those lowest (now-cleared) 32 bits of wacom_wac->serial[0] are
sent to userspace, causing xf86-input-wacom to ignore the event. If the event
was the final out-of-prox event, then xf86-input-wacom may remain in a state
where it believes the pen is in proximity and refuses to allow other devices
under its control (e.g. the touchscreen) to move the cursor.
It should be noted that EMR devices and devices which use both the
HID_DG_TOOLSERIALNUMBER and WACOM_HID_WD_SERIALHI usages (in that order) would
be immune to this issue. It appears only AES devices are affected.
Fixes: f85c9dc678 ("HID: wacom: generic: Support tool ID and additional tool types")
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df62db5be2 upstream.
Currently the snapshot trigger enables the probe and then allocates the
snapshot. If the probe triggers before the allocation, it could cause the
snapshot to fail and turn tracing off. It's best to allocate the snapshot
buffer first, and then enable the trigger. If something goes wrong in the
enabling of the trigger, the snapshot buffer is still allocated, but it can
also be freed by the user by writting zero into the snapshot buffer file.
Also add a check of the return status of alloc_snapshot().
Fixes: 77fd5c15e3 ("tracing: Add snapshot trigger to function probes")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c9f838d104 upstream.
This fixes CVE-2017-7472.
Running the following program as an unprivileged user exhausts kernel
memory by leaking thread keyrings:
#include <keyutils.h>
int main()
{
for (;;)
keyctl_set_reqkey_keyring(KEY_REQKEY_DEFL_THREAD_KEYRING);
}
Fix it by only creating a new thread keyring if there wasn't one before.
To make things more consistent, make install_thread_keyring_to_cred()
and install_process_keyring_to_cred() both return 0 if the corresponding
keyring is already present.
Fixes: d84f4f992c ("CRED: Inaugurate COW credentials")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1644fe041 upstream.
This fixes CVE-2017-6951.
Userspace should not be able to do things with the "dead" key type as it
doesn't have some of the helper functions set upon it that the kernel
needs. Attempting to use it may cause the kernel to crash.
Fix this by changing the name of the type to ".dead" so that it's rejected
up front on userspace syscalls by key_get_type_from_user().
Though this doesn't seem to affect recent kernels, it does affect older
ones, certainly those prior to:
commit c06cfb08b8
Author: David Howells <dhowells@redhat.com>
Date: Tue Sep 16 17:36:06 2014 +0100
KEYS: Remove key_type::match in favour of overriding default by match_preparse
which went in before 3.18-rc1.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee8f844e3c upstream.
This fixes CVE-2016-9604.
Keyrings whose name begin with a '.' are special internal keyrings and so
userspace isn't allowed to create keyrings by this name to prevent
shadowing. However, the patch that added the guard didn't fix
KEYCTL_JOIN_SESSION_KEYRING. Not only can that create dot-named keyrings,
it can also subscribe to them as a session keyring if they grant SEARCH
permission to the user.
This, for example, allows a root process to set .builtin_trusted_keys as
its session keyring, at which point it has full access because now the
possessor permissions are added. This permits root to add extra public
keys, thereby bypassing module verification.
This also affects kexec and IMA.
This can be tested by (as root):
keyctl session .builtin_trusted_keys
keyctl add user a a @s
keyctl list @s
which on my test box gives me:
2 keys in keyring:
180010936: ---lswrv 0 0 asymmetric: Build time autogenerated kernel key: ae3d4a31b82daa8e1a75b49dc2bba949fd992a05
801382539: --alswrv 0 0 user: a
Fix this by rejecting names beginning with a '.' in the keyctl.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
cc: linux-ima-devel@lists.sourceforge.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c4baad5029 upstream.
put_chars() stuffs the buffer it gets into an sg, but that buffer may be
on the stack. This breaks with CONFIG_VMAP_STACK=y (for me, it
manifested as printks getting turned into NUL bytes).
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Brad Spengler <spender@grsecurity.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f190e3aec upstream.
Commit 17ce039b4e ("[media] cxusb: don't do DMA on stack")
added a kmalloc'ed bounce buffer for writes, but missed to do the same
for reads. As the read only happens after the write is finished, we can
reuse the same buffer.
As dvb_usb_generic_rw handles a read length of 0 by itself, avoid calling
it using the dvb_usb_generic_read wrapper function.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Brad Spengler <spender@grsecurity.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a4866aa812 upstream.
Under CONFIG_STRICT_DEVMEM, reading System RAM through /dev/mem is
disallowed. However, on x86, the first 1MB was always allowed for BIOS
and similar things, regardless of it actually being System RAM. It was
possible for heap to end up getting allocated in low 1MB RAM, and then
read by things like x86info or dd, which would trip hardened usercopy:
usercopy: kernel memory exposure attempt detected from ffff880000090000 (dma-kmalloc-256) (4096 bytes)
This changes the x86 exception for the low 1MB by reading back zeros for
System RAM areas instead of blindly allowing them. More work is needed to
extend this to mmap, but currently mmap doesn't go through usercopy, so
hardened usercopy won't Oops the kernel.
Reported-by: Tommi Rantala <tommi.t.rantala@nokia.com>
Tested-by: Tommi Rantala <tommi.t.rantala@nokia.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Brad Spengler <spender@grsecurity.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5fa4086987 upstream.
Accessing the registers of the RTC block on Tegra requires the module
clock to be enabled. This only works because the RTC module clock will
be enabled by default during early boot. However, because the clock is
unused, the CCF will disable it at late_init time. This causes the RTC
to become unusable afterwards. This can easily be reproduced by trying
to use the RTC:
$ hwclock --rtc /dev/rtc1
This will hang the system. I ran into this by following up on a report
by Martin Michlmayr that reboot wasn't working on Tegra210 systems. It
turns out that the rtc-tegra driver's ->shutdown() implementation will
hang the CPU, because of the disabled clock, before the system can be
rebooted.
What confused me for a while is that the same driver is used on prior
Tegra generations where the hang can not be observed. However, as Peter
De Schrijver pointed out, this is because on 32-bit Tegra chips the RTC
clock is enabled by the tegra20_timer.c clocksource driver, which uses
the RTC to provide a persistent clock. This code is never enabled on
64-bit Tegra because the persistent clock infrastructure does not exist
on 64-bit ARM.
The proper fix for this is to add proper clock handling to the RTC
driver in order to ensure that the clock is enabled when the driver
requires it. All device trees contain the clock already, therefore
no additional changes are required.
Reported-by: Martin Michlmayr <tbm@cyrius.com>
Acked-By Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
[bwh: Backported to 4.9: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc272163ea upstream.
This patch fixes the following warning message seen when booting the
kernel as Dom0 with Xen on Intel machines.
[0.003000] [Firmware Bug]: CPU1: APIC id mismatch. Firmware: 0 APIC: 1]
The code generating the warning in validate_apic_and_package_id() matches
cpu_data(cpu).apicid (initialized in init_intel()->
detect_extended_topology() using cpuid) against the apicid returned from
xen_apic_read(). Now, xen_apic_read() makes a hypercall to retrieve apicid
for the boot cpu but returns 0 otherwise. Hence the warning gets thrown
for all but the boot cpu.
The idea behind xen_apic_read() returning 0 for apicid is that the
guests (even Dom0) should not need to know what physical processor their
vcpus are running on. This is because we currently do not have topology
information in Xen and also because xen allows more vcpus than physical
processors. However, boot cpu's apicid is required for loading
xen-acpi-processor driver on AMD machines. Look at following patch for
details:
commit 558daa289a ("xen/apic: Return the APIC ID (and version) for CPU
0.")
So to get rid of the warning, this patch modifies
xen_cpu_present_to_apicid() to return cpu_data(cpu).apicid instead of
calling xen_apic_read().
The warning is not seen on AMD machines because init_amd() populates
cpu_data(cpu).apicid by calling hard_smp_processor_id()->xen_apic_read()
as opposed to using apicid from cpuid as is done on Intel machines.
Signed-off-by: Mohit Gambhir <mohit.gambhir@oracle.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 98d610c373 upstream.
The accelerometer event relies on the ACERWMID_EVENT_GUID notify.
So, this patch changes the codes to setup accelerometer input device
when detected ACERWMID_EVENT_GUID. It avoids that the accel input
device created on every Acer machines.
In addition, patch adds a clearly parsing logic of accelerometer hid
to acer_wmi_get_handle_cb callback function. It is positive matching
the "SENR" name with "BST0001" device to avoid non-supported hardware.
Reported-by: Bjørn Mork <bjorn@mork.no>
Cc: Darren Hart <dvhart@infradead.org>
Signed-off-by: Lee, Chun-Yi <jlee@suse.com>
[andy: slightly massage commit message]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ebf79091bf upstream.
Select DW_DMAC_CORE like the rest of glue drivers do, e.g.
drivers/dma/dw/Kconfig.
While here group selectors under SND_SOC_INTEL_HASWELL and
SND_SOC_INTEL_BAYTRAIL.
Make platforms, which are using a common SST firmware driver, to be
dependent on DMADEVICES.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 005145378c upstream.
I ran into a stack frame size warning because of the on-stack copy of
the USB device structure:
drivers/media/usb/dvb-usb-v2/dvb_usb_core.c: In function 'dvb_usbv2_disconnect':
drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:1029:1: error: the frame size of 1104 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
Copying a device structure like this is wrong for a number of other reasons
too aside from the possible stack overflow. One of them is that the
dev_info() call will print the name of the device later, but AFAICT
we have only copied a pointer to the name earlier and the actual name
has been freed by the time it gets printed.
This removes the on-stack copy of the device and instead copies the
device name using kstrdup(). I'm ignoring the possible failure here
as both printk() and kfree() are able to deal with NULL pointers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f795cef0e upstream.
This fixes a bug in which the upper 32-bits of a 64-bit value which is
read by get_user() was lost on a 32-bit kernel.
While touching this code, split out pre-loading of %sr2 space register
and clean up code indent.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4702bbeefb upstream.
When we get an EINPROGRESS completion in lrw, we will end up marking
the request as done and freeing it. This then blows up when the
request is really completed as we've already freed the memory.
Fixes: 700cb3f5fe ("crypto: lrw - Convert to skcipher")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef0579b64e upstream.
The ahash API modifies the request's callback function in order
to clean up after itself in some corner cases (unaligned final
and missing finup).
When the request is complete ahash will restore the original
callback and everything is fine. However, when the request gets
an EBUSY on a full queue, an EINPROGRESS callback is made while
the request is still ongoing.
In this case the ahash API will incorrectly call its own callback.
This patch fixes the problem by creating a temporary request
object on the stack which is used to relay EINPROGRESS back to
the original completion function.
This patch also adds code to preserve the original flags value.
Fixes: ab6bf4e5e5 ("crypto: hash - Fix the pointer voodoo in...")
Reported-by: Sabrina Dubroca <sd@queasysnail.net>
Tested-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aa4a829bda upstream.
When we get an EINPROGRESS completion in xts, we will end up marking
the request as done and freeing it. This then blows up when the
request is really completed as we've already freed the memory.
Fixes: f1c131b454 ("crypto: xts - Convert to skcipher")
Reported-by: Nathan Royce <nroycea+kernel@gmail.com>
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e6534aebb2 upstream.
The algif_aead completion function tries to deduce the aead_request
from the crypto_async_request argument. This is broken because
the API does not guarantee that the same request will be pased to
the completion function. Only the value of req->data can be used
in the completion function.
This patch fixes it by storing a pointer to sk in areq and using
that instead of passing in sk through req->data.
Fixes: 83094e5e9e ("crypto: af_alg - add async support to...")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d879d0b8c1 upstream.
When function tracer has a pid filter, it adds a probe to sched_switch
to track if current task can be ignored. The probe checks the
ftrace_ignore_pid from current tr to filter tasks. But it misses to
delete the probe when removing an instance so that it can cause a crash
due to the invalid tr pointer (use-after-free).
This is easily reproducible with the following:
# cd /sys/kernel/debug/tracing
# mkdir instances/buggy
# echo $$ > instances/buggy/set_ftrace_pid
# rmdir instances/buggy
============================================================================
BUG: KASAN: use-after-free in ftrace_filter_pid_sched_switch_probe+0x3d/0x90
Read of size 8 by task kworker/0:1/17
CPU: 0 PID: 17 Comm: kworker/0:1 Tainted: G B 4.11.0-rc3 #198
Call Trace:
dump_stack+0x68/0x9f
kasan_object_err+0x21/0x70
kasan_report.part.1+0x22b/0x500
? ftrace_filter_pid_sched_switch_probe+0x3d/0x90
kasan_report+0x25/0x30
__asan_load8+0x5e/0x70
ftrace_filter_pid_sched_switch_probe+0x3d/0x90
? fpid_start+0x130/0x130
__schedule+0x571/0xce0
...
To fix it, use ftrace_clear_pids() to unregister the probe. As
instance_rmdir() already updated ftrace codes, it can just free the
filter safely.
Link: http://lkml.kernel.org/r/20170417024430.21194-2-namhyung@kernel.org
Fixes: 0c8916c342 ("tracing: Add rmdir to remove multibuffer instances")
Cc: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d72e9a7a93 upstream.
The copy_page is optimized memcpy for page-alinged address. If it is
used with non-page aligned address, it can corrupt memory which means
system corruption. With zram, it can happen with
1. 64K architecture
2. partial IO
3. slub debug
Partial IO need to allocate a page and zram allocates it via kmalloc.
With slub debug, kmalloc(PAGE_SIZE) doesn't return page-size aligned
address. And finally, copy_page(mem, cmem) corrupts memory.
So, this patch changes it to memcpy.
Actuaully, we don't need to change zram_bvec_write part because zsmalloc
returns page-aligned address in case of PAGE_SIZE class but it's not
good to rely on the internal of zsmalloc.
Note:
When this patch is merged to stable, clear_page should be fixed, too.
Unfortunately, recent zram removes it by "same page merge" feature so
it's hard to backport this patch to -stable tree.
I will handle it when I receive the mail from stable tree maintainer to
merge this patch to backport.
Fixes: 42e99bd ("zram: optimize memory operations with clear_page()/copy_page()")
Link: http://lkml.kernel.org/r/1492042622-12074-2-git-send-email-minchan@kernel.org
Signed-off-by: Minchan Kim <minchan@kernel.org>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f2cfa58b13 upstream.
Without a bool string present, using "# CONFIG_DEVPORT is not set" in
defconfig files would not actually unset devport. This esnured that
/dev/port was always on, but there are reasons a user may wish to
disable it (smaller kernel, attack surface reduction) if it's not being
used. Adding a message here in order to make this user visible.
Signed-off-by: Max Bires <jbires@google.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c4a3fa261b upstream.
There is a report that after commit 27622b061e ("cpufreq: Convert
to hotplug state machine"), the normal CPU offline/online cycle
fails on some platforms.
According to the ftrace result, this problem was triggered on
platforms using acpi-cpufreq as the default cpufreq driver,
and due to the lack of some ACPI freq method (eg. _PCT),
cpufreq_online() failed and returned a negative value, so the CPU
hotplug state machine rolled back the CPU online process. Actually,
from the user's perspective, the failure of cpufreq_online() should
not prevent that CPU from being brought up, although cpufreq might
not work on that CPU.
BTW, during system startup cpufreq_online() is not invoked via CPU
online but by the cpufreq device creation process, so the APs can be
brought up even though cpufreq_online() fails in that stage.
This patch ignores the return value of cpufreq_online/offline() and
lets the cpufreq framework deal with the failure. cpufreq_online()
itself will do a proper rollback in that case and if _PCT is missing,
the ACPI cpufreq driver will print a warning if the corresponding
debug options have been enabled.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=194581
Fixes: 27622b061e ("cpufreq: Convert to hotplug state machine")
Reported-and-tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a900152b5c upstream.
If the PWM was not enabled at U-Boot loader, PWM could not work for
clock always disabled at PWM driver. The PWM clock is enabled at
beginning of pwm_apply(), but disabled at end of pwm_apply().
If the PWM was enabled at U-Boot loader, PWM clock is always enabled
unless closed by ATF. The pwm-backlight might turn off the power at
early suspend, should disable PWM clock for saving power consume.
It is important to provide opportunity to enable/disable clock at PWM
driver, the PWM consumer should ensure correct order to call PWM enable
and disable, and PWM driver ensure state of PWM clock synchronized with
PWM enabled state.
Fixes: 2bf1c98aa5 ("pwm: rockchip: Add support for atomic update")
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4aa5615e08 upstream.
The following warning results from holding a lane spinlock,
preempt_disable(), or the btt map spinlock and then trying to take the
reconfig_mutex to walk the poison list and potentially add new entries.
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:747
in_atomic(): 1, irqs_disabled(): 0, pid: 17159, name: dd
[..]
Call Trace:
dump_stack+0x85/0xc8
___might_sleep+0x184/0x250
__might_sleep+0x4a/0x90
__mutex_lock+0x58/0x9b0
? nvdimm_bus_lock+0x21/0x30 [libnvdimm]
? __nvdimm_bus_badblocks_clear+0x2f/0x60 [libnvdimm]
? acpi_nfit_forget_poison+0x79/0x80 [nfit]
? _raw_spin_unlock+0x27/0x40
mutex_lock_nested+0x1b/0x20
nvdimm_bus_lock+0x21/0x30 [libnvdimm]
nvdimm_forget_poison+0x25/0x50 [libnvdimm]
nvdimm_clear_poison+0x106/0x140 [libnvdimm]
nsio_rw_bytes+0x164/0x270 [libnvdimm]
btt_write_pg+0x1de/0x3e0 [nd_btt]
? blk_queue_enter+0x30/0x290
btt_make_request+0x11a/0x310 [nd_btt]
? blk_queue_enter+0xb7/0x290
? blk_queue_enter+0x30/0x290
generic_make_request+0x118/0x3b0
As a minimal fix, disable error clearing when the BTT is enabled for the
namespace. For the final fix a larger rework of the poison list locking
is needed.
Note that this is not a problem in the blk case since that path never
calls nvdimm_clear_poison().
Fixes: 82bf1037f2 ("libnvdimm: check and clear poison before writing to pmem")
Cc: Dave Jiang <dave.jiang@intel.com>
[jeff: dynamically disable error clearing in the btt case]
Suggested-by: Jeff Moyer <jmoyer@redhat.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Reported-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0beb2012a1 upstream.
Holding the reconfig_mutex over a potential userspace fault sets up a
lockdep dependency chain between filesystem-DAX and the libnvdimm ioctl
path. Move the user access outside of the lock.
[ INFO: possible circular locking dependency detected ]
4.11.0-rc3+ #13 Tainted: G W O
-------------------------------------------------------
fallocate/16656 is trying to acquire lock:
(&nvdimm_bus->reconfig_mutex){+.+.+.}, at: [<ffffffffa00080b1>] nvdimm_bus_lock+0x21/0x30 [libnvdimm]
but task is already holding lock:
(jbd2_handle){++++..}, at: [<ffffffff813b4944>] start_this_handle+0x104/0x460
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 (jbd2_handle){++++..}:
lock_acquire+0xbd/0x200
start_this_handle+0x16a/0x460
jbd2__journal_start+0xe9/0x2d0
__ext4_journal_start_sb+0x89/0x1c0
ext4_dirty_inode+0x32/0x70
__mark_inode_dirty+0x235/0x670
generic_update_time+0x87/0xd0
touch_atime+0xa9/0xd0
ext4_file_mmap+0x90/0xb0
mmap_region+0x370/0x5b0
do_mmap+0x415/0x4f0
vm_mmap_pgoff+0xd7/0x120
SyS_mmap_pgoff+0x1c5/0x290
SyS_mmap+0x22/0x30
entry_SYSCALL_64_fastpath+0x1f/0xc2
-> #1 (&mm->mmap_sem){++++++}:
lock_acquire+0xbd/0x200
__might_fault+0x70/0xa0
__nd_ioctl+0x683/0x720 [libnvdimm]
nvdimm_ioctl+0x8b/0xe0 [libnvdimm]
do_vfs_ioctl+0xa8/0x740
SyS_ioctl+0x79/0x90
do_syscall_64+0x6c/0x200
return_from_SYSCALL_64+0x0/0x7a
-> #0 (&nvdimm_bus->reconfig_mutex){+.+.+.}:
__lock_acquire+0x16b6/0x1730
lock_acquire+0xbd/0x200
__mutex_lock+0x88/0x9b0
mutex_lock_nested+0x1b/0x20
nvdimm_bus_lock+0x21/0x30 [libnvdimm]
nvdimm_forget_poison+0x25/0x50 [libnvdimm]
nvdimm_clear_poison+0x106/0x140 [libnvdimm]
pmem_do_bvec+0x1c2/0x2b0 [nd_pmem]
pmem_make_request+0xf9/0x270 [nd_pmem]
generic_make_request+0x118/0x3b0
submit_bio+0x75/0x150
Fixes: 62232e45f4 ("libnvdimm: control (ioctl) messages for nvdimm_bus and nvdimm devices")
Cc: Dave Jiang <dave.jiang@intel.com>
Reported-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe514739d8 upstream.
Commit a1f3e4d6a0 "libnvdimm, region: update nd_region_available_dpa()
for multi-pmem support" reworked blk dpa (DIMM Physical Address)
accounting to comprehend multiple pmem namespace allocations aliasing
with a given blk-dpa range.
The following call trace is a result of failing to account for allocated
blk capacity.
WARNING: CPU: 1 PID: 2433 at tools/testing/nvdimm/../../../drivers/nvdimm/names
4 size_store+0x6f3/0x930 [libnvdimm]
nd_region region5: allocation underrun: 0x0 of 0x1000000 bytes
[..]
Call Trace:
dump_stack+0x86/0xc3
__warn+0xcb/0xf0
warn_slowpath_fmt+0x5f/0x80
size_store+0x6f3/0x930 [libnvdimm]
dev_attr_store+0x18/0x30
If a given blk-dpa allocation does not alias with any pmem ranges then
the full allocation should be accounted as busy space, not the size of
the current pmem contribution to the region.
The thinkos that led to this confusion was not realizing that the struct
resource management is already guaranteeing no collisions between pmem
allocations and blk allocations on the same dimm. Also, we do not try to
support blk allocations in aliased pmem holes.
This patch also fixes a case where the available blk goes negative.
Fixes: a1f3e4d6a0 ("libnvdimm, region: update nd_region_available_dpa() for multi-pmem support").
Reported-by: Dariusz Dokupil <dariusz.dokupil@intel.com>
Reported-by: Dave Jiang <dave.jiang@intel.com>
Reported-by: Vishal Verma <vishal.l.verma@intel.com>
Tested-by: Dave Jiang <dave.jiang@intel.com>
Tested-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3278682123 upstream.
Fixes the mess observed in e.g. rsync over a noisy link we'd been
seeing since last Summer. What happens is that we copy part of
a datagram before noticing a checksum mismatch. Datagram will be
resent, all right, but we want the next try go into the same place,
not after it...
All this family of primitives (copy/checksum and copy a datagram
into destination) is "all or nothing" sort of interface - either
we get 0 (meaning that copy had been successful) or we get an
error (and no way to tell how much had been copied before we ran
into whatever error it had been). Make all of them leave iterator
unadvanced in case of errors - all callers must be able to cope
with that (an error might've been caught before the iterator had
been advanced), it costs very little to arrange, it's safer for
callers and actually fixes at least one bug in said callers.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 27c0e3748e upstream.
opposite to iov_iter_advance(); the caller is responsible for never
using it to move back past the initial position.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9121b15b56 upstream.
Connecting to the backend isn't working reliably in xen-fbfront: in
case XenbusStateInitWait of the backend has been missed the backend
transition to XenbusStateConnected will trigger the connected state
only without doing the actions required when the backend has
connected.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 49cb77e297 upstream.
This patch closes a race between se_lun deletion during configfs
unlink in target_fabric_port_unlink() -> core_dev_del_lun()
-> core_tpg_remove_lun(), when transport_clear_lun_ref() blocks
waiting for percpu_ref RCU grace period to finish, but a new
NodeACL mappedlun is added before the RCU grace period has
completed.
This can happen in target_fabric_mappedlun_link() because it
only checks for se_lun->lun_se_dev, which is not cleared until
after transport_clear_lun_ref() percpu_ref RCU grace period
finishes.
This bug originally manifested as NULL pointer dereference
OOPsen in target_stat_scsi_att_intr_port_show_attr_dev() on
v4.1.y code, because it dereferences lun->lun_se_dev without
a explicit NULL pointer check.
In post v4.1 code with target-core RCU conversion, the code
in target_stat_scsi_att_intr_port_show_attr_dev() no longer
uses se_lun->lun_se_dev, but the same race still exists.
To address the bug, go ahead and set se_lun>lun_shutdown as
early as possible in core_tpg_remove_lun(), and ensure new
NodeACL mappedlun creation in target_fabric_mappedlun_link()
fails during se_lun shutdown.
Reported-by: James Shen <jcs@datera.io>
Cc: James Shen <jcs@datera.io>
Tested-by: James Shen <jcs@datera.io>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c856152cb upstream.
We previously made sure that the reported disk capacity was less than
0xffffffff blocks when the kernel was not compiled with large sector_t
support (CONFIG_LBDAF). However, this check assumed that the capacity
was reported in units of 512 bytes.
Add a sanity check function to ensure that we only enable disks if the
entire reported capacity can be expressed in terms of sector_t.
Reported-by: Steve Magnani <steve.magnani@digidescorp.com>
Cc: Bart Van Assche <Bart.VanAssche@sandisk.com>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf6061b17a upstream.
Add fix to read correct register value for ISP82xx, during check for
register disconnect.ISP82xx has different base register.
Fixes: a465537ad1 ("qla2xxx: Disable the adapter and skip error recovery in case of register disconnect")
Signed-off-by: Sawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6780414519 upstream.
If device reports a small max_xfer_blocks and a zero opt_xfer_blocks, we
end up using BLK_DEF_MAX_SECTORS, which is wrong and r/w of that size
may get error.
[mkp: tweaked to avoid setting rw_max twice and added typecast]
Fixes: ca369d51b3 ("block/sd: Fix device-imposed transfer length limits")
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a00a786251 upstream.
Kefeng Wang discovered that old versions of the QEMU CD driver would
return mangled mode data causing us to walk off the end of the buffer in
an attempt to parse it. Sanity check the returned mode sense data.
Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Tested-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c99de981f upstream.
Once upon a time back in 2009, a work-around was added to support
the GlobalSAN iSCSI initiator v3.3 for MacOSX, which during login
did not propose nor respond to MaxBurstLength, FirstBurstLength,
DefaultTime2Wait and DefaultTime2Retain keys.
The work-around in iscsi_check_proposer_for_optional_reply()
allowed the missing keys to be proposed, but did not require
waiting for a response before moving to full feature phase
operation. This allowed GlobalSAN v3.3 to work out-of-the
box, and for many years we didn't run into login interopt
issues with any other initiators..
Until recently, when Martin tried a QLogic 57840S iSCSI Offload
HBA on Windows 2016 which completed login, but subsequently
failed with:
Got unknown iSCSI OpCode: 0x43
The issue was QLogic MSFT side did not propose DefaultTime2Wait +
DefaultTime2Retain, so LIO proposes them itself, and immediately
transitions to full feature phase because of the GlobalSAN hack.
However, the QLogic MSFT side still attempts to respond to
DefaultTime2Retain + DefaultTime2Wait, even though LIO has set
ISCSI_FLAG_LOGIN_NEXT_STAGE3 + ISCSI_FLAG_LOGIN_TRANSIT
in last login response.
So while the QLogic MSFT side should have been proposing these
two keys to start, it was doing the correct thing per RFC-3720
attempting to respond to proposed keys before transitioning to
full feature phase.
All that said, recent versions of GlobalSAN iSCSI (v5.3.0.541)
does correctly propose the four keys during login, making the
original work-around moot.
So in order to allow QLogic MSFT to run unmodified as-is, go
ahead and drop this long standing work-around.
Reported-by: Martin Svec <martin.svec@zoner.cz>
Cc: Martin Svec <martin.svec@zoner.cz>
Cc: Himanshu Madhani <Himanshu.Madhani@cavium.com>
Cc: Arun Easi <arun.easi@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit efb2ea770b upstream.
This patch fixes a iscsi-target specific TMR reference leak
during session shutdown, that could occur when a TMR was
quiesced before the hand-off back to iscsi-target code
via transport_cmd_check_stop_to_fabric().
The reference leak happens because iscsit_free_cmd() was
incorrectly skipping the final target_put_sess_cmd() for
TMRs when transport_generic_free_cmd() returned zero because
the se_cmd->cmd_kref did not reach zero, due to the missing
se_cmd assignment in original code.
The result was iscsi_cmd and it's associated se_cmd memory
would be freed once se_sess->sess_cmd_map where released,
but the associated se_tmr_req was leaked and remained part
of se_device->dev_tmr_list.
This bug would manfiest itself as kernel paging request
OOPsen in core_tmr_lun_reset(), when a left-over se_tmr_req
attempted to dereference it's se_cmd pointer that had
already been released during normal session shutdown.
To address this bug, go ahead and treat ISCSI_OP_SCSI_CMD
and ISCSI_OP_SCSI_TMFUNC the same when there is an extra
se_cmd->cmd_kref to drop in iscsit_free_cmd(), and use
op_scsi to signal __iscsit_free_cmd() when the former
needs to clear any further iscsi related I/O state.
Reported-by: Rob Millner <rlm@daterainc.com>
Cc: Rob Millner <rlm@daterainc.com>
Reported-by: Chu Yuan Lin <cyl@datera.io>
Cc: Chu Yuan Lin <cyl@datera.io>
Tested-by: Chu Yuan Lin <cyl@datera.io>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 55d728a40d upstream.
On UEFI systems, the PCI subsystem is enumerated by the firmware,
and if a graphical framebuffer is exposed via a PCI device, its base
address and size are exposed to the OS via the Graphics Output
Protocol (GOP).
On arm64 PCI systems, the entire PCI hierarchy is reconfigured from
scratch at boot. This may result in the GOP framebuffer address to
become stale, if the BAR covering the framebuffer is modified. This
will cause the framebuffer to become unresponsive, and may in some
cases result in unpredictable behavior if the range is reassigned to
another device.
So add a non-x86 quirk to the EFI fb driver to find the BAR associated
with the GOP base address, and claim the BAR resource so that the PCI
core will not move it.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Jones <pjones@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: leif.lindholm@linaro.org
Cc: linux-efi@vger.kernel.org
Cc: lorenzo.pieralisi@arm.com
Fixes: 9822504c1f ("efifb: Enable the efi-framebuffer platform driver ...")
Link: http://lkml.kernel.org/r/20170404152744.26687-3-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 540f4c0e89 upstream.
The UEFI Specification permits Graphics Output Protocol (GOP) instances
without direct framebuffer access. This is indicated in the Mode structure
with a PixelFormat enumeration value of PIXEL_BLT_ONLY. Given that the
kernel does not know how to drive a Blt() only framebuffer (which is only
permitted before ExitBootServices() anyway), we should disregard such
framebuffers when looking for a GOP instance that is suitable for use as
the boot console.
So modify the EFI GOP initialization to not use a PIXEL_BLT_ONLY instance,
preventing attempts later in boot to use an invalid screen_info.lfb_base
address.
Signed-off-by: Eugene Cohen <eugene@hp.com>
[ Moved the Blt() only check into the loop and clarified that Blt() only GOPs are unusable by the kernel. ]
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: leif.lindholm@linaro.org
Cc: linux-efi@vger.kernel.org
Cc: lorenzo.pieralisi@arm.com
Fixes: 9822504c1f ("efifb: Enable the efi-framebuffer platform driver ...")
Link: http://lkml.kernel.org/r/20170404152744.26687-2-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 409c1b250e upstream.
The patch 554bfeceb8 ("parisc: Fix access
fault handling in pa_memcpy()") reimplements the pa_memcpy function.
Unfortunatelly, it makes the kernel unbootable. The crash happens in the
function ide_complete_cmd where memcpy is called with the same source
and destination address.
This patch fixes a few bugs in pa_memcpy:
* When jumping to .Lcopy_loop_16 for the first time, don't skip the
instruction "ldi 31,t0" (this bug made the kernel unbootable)
* Use the COND macro when comparing length, so that the comparison is
64-bit (a theoretical issue, in case the length is greater than
0xffffffff)
* Don't use the COND macro after the "extru" instruction (the PA-RISC
specification says that the upper 32-bits of extru result are undefined,
although they are set to zero in practice)
* Fix exception addresses in .Lcopy16_fault and .Lcopy8_fault
* Rename .Lcopy_loop_4 to .Lcopy_loop_8 (so that it is consistent with
.Lcopy8_fault)
Fixes: 554bfeceb8 ("parisc: Fix access fault handling in pa_memcpy()")
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b03b99a329 upstream.
While reviewing the -stable patch for commit 86ef58a4e3 "nfit,
libnvdimm: fix interleave set cookie calculation" Ben noted:
"This is returning an int, thus it's effectively doing a 32-bit
comparison and not the 64-bit comparison you say is needed."
Update the compare operation to be immune to this integer demotion problem.
Cc: Nicholas Moulin <nicholas.w.moulin@linux.intel.com>
Fixes: 86ef58a4e3 ("nfit, libnvdimm: fix interleave set cookie calculation")
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6fdc6dd902 upstream.
The vsyscall32 sysctl can racy against a concurrent fork when it switches
from disabled to enabled:
arch_setup_additional_pages()
if (vdso32_enabled)
--> No mapping
sysctl.vsysscall32()
--> vdso32_enabled = true
create_elf_tables()
ARCH_DLINFO_IA32
if (vdso32_enabled) {
--> Add VDSO entry with NULL pointer
Make ARCH_DLINFO_IA32 check whether the VDSO mapping has been set up for
the newly forked process or not.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Andy Lutomirski <luto@amacapital.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mathias Krause <minipli@googlemail.com>
Link: http://lkml.kernel.org/r/20170410151723.602367196@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 11e63f6d92 upstream.
Before we rework the "pmem api" to stop abusing __copy_user_nocache()
for memcpy_to_pmem() we need to fix cases where we may strand dirty data
in the cpu cache. The problem occurs when copy_from_iter_pmem() is used
for arbitrary data transfers from userspace. There is no guarantee that
these transfers, performed by dax_iomap_actor(), will have aligned
destinations or aligned transfer lengths. Backstop the usage
__copy_user_nocache() with explicit cache management in these unaligned
cases.
Yes, copy_from_iter_pmem() is now too big for an inline, but addressing
that is saved for a later patch that moves the entirety of the "pmem
api" into the pmem driver directly.
Fixes: 5de490daec ("pmem: add copy_from_iter_pmem() and clear_pmem()")
Cc: <x86@kernel.org>
Cc: Jan Kara <jack@suse.cz>
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f6266a561 upstream.
Reserving a runtime region results in splitting the EFI memory
descriptors for the runtime region. This results in runtime region
descriptors with bogus memory mappings, leading to interesting crashes
like the following during a kexec:
general protection fault: 0000 [#1] SMP
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.11.0-rc1 #53
Hardware name: Wiwynn Leopard-Orv2/Leopard-DDR BW, BIOS LBM05 09/30/2016
RIP: 0010:virt_efi_set_variable()
...
Call Trace:
efi_delete_dummy_variable()
efi_enter_virtual_mode()
start_kernel()
? set_init_arg()
x86_64_start_reservations()
x86_64_start_kernel()
start_cpu()
...
Kernel panic - not syncing: Fatal exception
Runtime regions will not be freed and do not need to be reserved, so
skip the memmap modification in this case.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Dave Young <dyoung@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Jones <pjones@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Fixes: 8e80632fb2 ("efi/esrt: Use efi_mem_reserve() and avoid a kmalloc()")
Link: http://lkml.kernel.org/r/20170412152719.9779-2-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1fa839b498 upstream.
This fixes Continuous Availability when errors during
file reopen are encountered.
cifs_user_readv and cifs_user_writev would wait for ever if
results of cifs_reopen_file are not stored and for later inspection.
In fact, results are checked and, in case of errors, a chain
of function calls leading to reads and writes to be scheduled in
a separate thread is skipped.
These threads will wake up the corresponding waiters once reads
and writes are done.
However, given the return value is not stored, when rc is checked
for errors a previous one (always zero) is inspected instead.
This leads to pending reads/writes added to the list, making
cifs_user_readv and cifs_user_writev wait for ever.
Signed-off-by: Germano Percossi <germano.percossi@citrix.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit da2ba564a6 upstream.
Forked from GP106 implementation.
Split out from commit enabling secboot/gr support so that it can be
added to earlier kernels.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2907e8670b upstream.
When the atomic support was added to nouveau, the DRM core did not do this.
However, later in the same merge window, a commit (drm/fence: add in-fences
support) was merged that added it, leading to use-after-frees of the fence
object.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f94773b9f5 upstream.
The NV4A (aka NV44A) is an oddity in the family. It only comes in AGP
and PCI varieties, rather than a core PCIE chip with a bridge for
AGP/PCI as necessary. As a result, it appears that the MMU is also
non-functional. For AGP cards, the vast majority of the NV4A lineup,
this worked out since we force AGP cards to use the nv04 mmu. However
for PCI variants, this did not work.
Switching to the NV04 MMU makes it work like a charm. Thanks to mwk for
the suggestion. This should be a no-op for NV4A AGP boards, as they were
using it already.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=70388
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ec1688c53 upstream.
Otherwise lockdep says:
[ 1337.483798] ================================================
[ 1337.483999] [ BUG: lock held when returning to user space! ]
[ 1337.484252] 4.11.0-rc6 #19 Not tainted
[ 1337.484423] ------------------------------------------------
[ 1337.484626] mount/14766 is leaving the kernel with locks still held!
[ 1337.484841] 1 lock held by mount/14766:
[ 1337.485017] #0: (&type->s_umount_key#33/1){+.+.+.}, at: [<ffffffff8124171f>] sget_userns+0x2af/0x520
Caught by xfstests generic/413 which tried to mount with the unsupported
mount option dax. Then xfstests generic/422 ran sync which deadlocks.
Signed-off-by: Martin Brandenburg <martin@omnibond.com>
Acked-by: Mike Marshall <hubcap@omnibond.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a5d68ba858 upstream.
For the bidirectional case, the Data-Out buffer blocks will always at
the head of the tcmu_cmd's bitmap, and before gathering the Data-In
buffer, first of all it should skip the Data-Out ones, or the device
supporting BIDI commands won't work.
Fixed: 26418649ee ("target/user: Introduce data_bitmap, replace
data_length/data_head/data_tail")
Reported-by: Ilias Tsitsimpis <iliastsi@arrikto.com>
Tested-by: Ilias Tsitsimpis <iliastsi@arrikto.com>
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit abe342a5b4 upstream.
The t_data_nents and t_bidi_data_nents are the numbers of the
segments, but it couldn't be sure the block size equals to size
of the segment.
For the worst case, all the blocks are discontiguous and there
will need the same number of iovecs, that's to say: blocks == iovs.
So here just set the number of iovs to block count needed by tcmu
cmd.
Tested-by: Ilias Tsitsimpis <iliastsi@arrikto.com>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ab22d2604c upstream.
If there has BIDI data, its first iov[] will overwrite the last
iov[] for se_cmd->t_data_sg.
To fix this, we can just increase the iov pointer, but this may
introuduce a new memory leakage bug: If the se_cmd->data_length
and se_cmd->t_bidi_data_sg->length are all not aligned up to the
DATA_BLOCK_SIZE, the actual length needed maybe larger than just
sum of them.
So, this could be avoided by rounding all the data lengthes up
to DATA_BLOCK_SIZE.
Reviewed-by: Mike Christie <mchristi@redhat.com>
Tested-by: Ilias Tsitsimpis <iliastsi@arrikto.com>
Reviewed-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 264d509637 upstream.
The retry queue is intended to provide a temporary buffer in the case
of transient errors when communicating with auditd, it is not meant
as a long life queue, that functionality is provided by the hold
queue.
This patch fixes a problem identified by Seth where the retry queue
could grow uncontrollably if an auditd instance did not connect to
the kernel to drain the queues. This commit fixes this by doing the
following:
* Make sure we always call auditd_reset() if we decide the connection
with audit is really dead. There were some cases in
kauditd_hold_skb() where we did not reset the connection, this patch
relocates the reset calls to kauditd_thread() so all the error
conditions are caught and the connection reset. As a side effect,
this means we could move auditd_reset() and get rid of the forward
definition at the top of kernel/audit.c.
* We never checked the status of the auditd connection when
processing the main audit queue which meant that the retry queue
could grow unchecked. This patch adds a call to auditd_reset()
after the main queue has been processed if auditd is not connected,
the auditd_reset() call will make sure the retry and hold queues are
correctly managed/flushed so that the retry queue remains reasonable.
Reported-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 77f88796ce upstream.
Creation of a kthread goes through a couple interlocked stages between
the kthread itself and its creator. Once the new kthread starts
running, it initializes itself and wakes up the creator. The creator
then can further configure the kthread and then let it start doing its
job by waking it up.
In this configuration-by-creator stage, the creator is the only one
that can wake it up but the kthread is visible to userland. When
altering the kthread's attributes from userland is allowed, this is
fine; however, for cases where CPU affinity is critical,
kthread_bind() is used to first disable affinity changes from userland
and then set the affinity. This also prevents the kthread from being
migrated into non-root cgroups as that can affect the CPU affinity and
many other things.
Unfortunately, the cgroup side of protection is racy. While the
PF_NO_SETAFFINITY flag prevents further migrations, userland can win
the race before the creator sets the flag with kthread_bind() and put
the kthread in a non-root cgroup, which can lead to all sorts of
problems including incorrect CPU affinity and starvation.
This bug got triggered by userland which periodically tries to migrate
all processes in the root cpuset cgroup to a non-root one. Per-cpu
workqueue workers got caught while being created and ended up with
incorrected CPU affinity breaking concurrency management and sometimes
stalling workqueue execution.
This patch adds task->no_cgroup_migration which disallows the task to
be migrated by userland. kthreadd starts with the flag set making
every child kthread start in the root cgroup with migration
disallowed. The flag is cleared after the kthread finishes
initialization by which time PF_NO_SETAFFINITY is set if the kthread
should stay in the root cgroup.
It'd be better to wait for the initialization instead of failing but I
couldn't think of a way of implementing that without adding either a
new PF flag, or sleeping and retrying from waiting side. Even if
userland depends on changing cgroup membership of a kthread, it either
has to be synchronized with kthread_create() or periodically repeat,
so it's unlikely that this would break anything.
v2: Switch to a simpler implementation using a new task_struct bit
field suggested by Oleg.
Signed-off-by: Tejun Heo <tj@kernel.org>
Suggested-by: Oleg Nesterov <oleg@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Reported-and-debugged-by: Chris Mason <clm@fb.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b6867c2ce upstream.
Subtracting tp_sizeof_priv from tp_block_size and casting to int
to check whether one is less then the other doesn't always work
(both of them are unsigned ints).
Compare them as is instead.
Also cast tp_sizeof_priv to u64 before using BLK_PLUS_PRIV, as
it can overflow inside BLK_PLUS_PRIV otherwise.
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 33fa46d7b3 upstream.
In case caam_jr_alloc() fails, ctx->dev carries the error code,
thus accessing it with dev_err() is incorrect.
Fixes: 8c419778ab ("crypto: caam - add support for RSA algorithm")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40c98cb57c upstream.
RNG instantiation was previously fixed by
commit 62743a4145 ("crypto: caam - fix RNG init descriptor ret. code checking")
while deinstantiation was not addressed.
Since the descriptors used are similar, in the sense that they both end
with a JUMP HALT command, checking for errors should be similar too,
i.e. status code 7000_0000h should be considered successful.
Fixes: 1005bccd7a ("crypto: caam - enable instantiation of all RNG4 state handles")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c25f8064c1 upstream.
Commit dda45f701c ("MIPS: Switch to the irq_stack in interrupts")
changed both the normal and vectored interrupt handlers. Unfortunately
the vectored version, "except_vec_vi_handler", was incorrectly modified
to unconditionally jal to plat_irq_dispatch, rather than doing a jalr to
the vectored handler that has been set up. This is ok for many platforms
which set the vectored handler to plat_irq_dispatch anyway, but will
cause problems with platforms that use other handlers.
Fixes: dda45f701c ("MIPS: Switch to the irq_stack in interrupts")
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15110/
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dda45f701c upstream.
When enterring interrupt context via handle_int or except_vec_vi, switch
to the irq_stack of the current CPU if it is not already in use.
The current stack pointer is masked with the thread size and compared to
the base or the irq stack. If it does not match then the stack pointer
is set to the top of that stack, otherwise this is a nested irq being
handled on the irq stack so the stack pointer should be left as it was.
The in-use stack pointer is placed in the callee saved register s1. It
will be saved to the stack when plat_irq_dispatch is invoked and can be
restored once control returns here.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Acked-by: Jason A. Donenfeld <jason@zx2c4.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14743/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 510d86362a upstream.
The SAVE_SOME macro is used to save the execution context on all
exceptions.
If an exception occurs while executing user code, the stack is switched
to the kernel's stack for the current task, and register $28 is switched
to point to the current_thread_info, which is at the bottom of the stack
region.
If the exception occurs while executing kernel code, the stack is left,
and this change ensures that register $28 is not updated. This is the
correct behaviour when the kernel can be executing on the separate irq
stack, because the thread_info will not be at the base of it.
With this change, register $28 is only switched to it's kernel
conventional usage of the currrent thread info pointer at the point at
which execution enters kernel space. Doing it on every exception was
redundant, but OK without an IRQ stack, but will be erroneous once that
is introduced.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Acked-by: Jason A. Donenfeld <jason@zx2c4.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14742/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 93c7018ec1 upstream.
We might kill TX or RX urb during rt2x00usb_flush_entry(), what can
cause anchor list corruption like shown below:
[ 2074.035633] WARNING: CPU: 2 PID: 14480 at lib/list_debug.c:33 __list_add+0xac/0xc0
[ 2074.035634] list_add corruption. prev->next should be next (ffff88020f362c28), but was dead000000000100. (prev=ffff8801d161bb70).
<snip>
[ 2074.035670] Call Trace:
[ 2074.035672] [<ffffffff813bde47>] dump_stack+0x63/0x8c
[ 2074.035674] [<ffffffff810a2231>] __warn+0xd1/0xf0
[ 2074.035676] [<ffffffff810a22af>] warn_slowpath_fmt+0x5f/0x80
[ 2074.035678] [<ffffffffa073855d>] ? rt2x00usb_register_write_lock+0x3d/0x60 [rt2800usb]
[ 2074.035679] [<ffffffff813dbe4c>] __list_add+0xac/0xc0
[ 2074.035681] [<ffffffff81591c6c>] usb_anchor_urb+0x4c/0xa0
[ 2074.035683] [<ffffffffa07322af>] rt2x00usb_kick_rx_entry+0xaf/0x100 [rt2x00usb]
[ 2074.035684] [<ffffffffa0732322>] rt2x00usb_clear_entry+0x22/0x30 [rt2x00usb]
To fix do not anchor TX and RX urb's, it is not needed as during
shutdown we kill those urbs in rt2x00usb_free_entries().
Cc: Vishal Thanki <vishalthanki@gmail.com>
Fixes: 8b4c000931 ("rt2x00usb: Use usb anchor to manage URB")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eb68d0324d upstream.
The deamon through which the kernel module communicates with the userspace
part of Orangefs, the "client-core", sends initialization data to the
kernel module with ioctl. The initialization data was built by the
client-core in a 2k buffer and copy_from_user'd into a 1k buffer
in the kernel module. When more than 1k of initialization data needed
to be sent, some was lost, reducing the usability of the control by which
debug levels are set. This patch sets the kernel side buffer to 2K to
match the userspace side...
Signed-off-by: Mike Marshall <hubcap@omnibond.com>
Signed-off-by: Martin Brandenburg <martin@omnibond.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05973c2efb upstream.
This patch is simlar to one Dan Carpenter sent me, cleans
up some return codes and whitespace errors. There was one
place where he thought inserting an error message into
the ring buffer might be too chatty, I hope I convinced him
othewise. As a consolation <g> I changed a truly chatty
error message in another location into a debug message,
system-admins had already yelled at me about that one...
Signed-off-by: Mike Marshall <hubcap@omnibond.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b7048ea12f upstream.
Currently ILK-BDW explicitly disable LP1+ watermarks from their
.init_clock_gating() hooks. Unfortunately that hook gets called way too
late since by that time we've already initialized all the watermark
state tracking which then gets out of sync with the hardware state.
We may eventually want to consider killing off the explicit LP1+
disable from .init_clock_gating(). In the meantime however, we can
avoid the problem by reordering the init sequence such that
intel_modeset_init_hw()->intel_init_clock_gating() gets called
prior to the hardware state takeover.
I suppose prior to the two stage watermark programming we were
magically saved by something that forced the watermarks to be
reprogrammed fully after .init_clock_gating() got called. But
now that no longer happens.
Note that the diff might look a bit odd as it kills off one
call of intel_update_cdclk(), but that's fine because
intel_modeset_init_hw() does the exact same thing. Previously
we just did it twice.
Actually even this new init sequence is pretty bogus as
.init_clock_gating() really should be called before any gem
hardware init since it can configure various clock gating
workarounds and whatnot that affect the GT side as well. Also
intel_modeset_init() really should get split up into better
defined init stages. Another "fun" detail is that
intel_modeset_gem_init() is where RPS/RC6 gets configured.
Why that is done from the display code is beyond me. I've
decided to leave all this be for now, and just try to fix
the init sequence enough for watermarks to work.
Cc: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Cc: David Purton <dcpurton@marshwiggle.net>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reported-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Reported-by: David Purton <dcpurton@marshwiggle.net>
Tested-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96645
Fixes: ed4a6a7ca8 ("drm/i915: Add two-stage ILK-style watermark programming (v11)")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170220140443.30891-1-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170315143158.31780-1-ville.syrjala@linux.intel.com
(cherry picked from commit 5be6e33400)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f5418e564 upstream.
This patch makes the I915_PARAM_HAS_EXEC_CONSTANTS getparam return 0
(indicating the optional feature is not supported), and makes execbuf
always return -EINVAL if the flags are used.
Apparently, no userspace ever shipped which used this optional feature:
I checked the git history of Mesa, xf86-video-intel, libva, and Beignet,
and there were zero commits showing a use of these flags. Kernel commit
72bfa19c8d apparently introduced the feature prematurely. According
to Chris, the intention was to use this in cairo-drm, but "the use was
broken for gen6", so I don't think it ever happened.
'relative_constants_mode' has always been tracked per-device, but this
has actually been wrong ever since hardware contexts were introduced, as
the INSTPM register is saved (and automatically restored) as part of the
render ring context. The software per-device value could therefore get
out of sync with the hardware per-context value. This meant that using
them is actually unsafe: a client which tried to use them could damage
the state of other clients, causing the GPU to interpret their BO
offsets as absolute pointers, leading to bogus memory reads.
These flags were also never ported to execlist mode, making them no-ops
on Gen9+ (which requires execlists), and Gen8 in the default mode.
On Gen8+, userspace can write these registers directly, achieving the
same effect. On Gen6-7.5, it likely makes sense to extend the command
parser to support them. I don't think anyone wants this on Gen4-5.
Based on a patch by Dave Gordon.
v3: Return -ENODEV for the getparam, as this is what we do for other
obsolete features. Suggested by Chris Wilson.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92448
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170215093446.21291-1-kenneth@whitecape.org
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170313170433.26843-1-chris@chris-wilson.co.uk
(cherry picked from commit ef0f411f51)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 34dc8993ee upstream.
Certain Baytrails, namely the 4 cpu core variants, have been
plaqued by spurious system hangs, mostly occurring with light loads.
Multiple bisects by various people point to a commit which changes the
reclocking strategy for Baytrail to follow its bigger brethen:
commit 8fb55197e6 ("drm/i915: Agressive downclocking on Baytrail")
There is also a review comment attached to this commit from Deepak S
on avoiding punit access on Cherryview and thus it was excluded on
common reclocking path. By taking the same approach and omitting
the punit access by not tweaking the thresholds when the hardware
has been asked to move into different frequency, considerable gains
in stability have been observed.
With J1900 box, light render/video load would end up in system hang
in usually less than 12 hours. With this patch applied, the cumulative
uptime has now been 34 days without issues. To provoke system hang,
light loads on both render and bsd engines in parallel have been used:
glxgears >/dev/null 2>/dev/null &
mpv --vo=vaapi --hwdec=vaapi --loop=inf vid.mp4
So far, author has not witnessed system hang with above load
and this patch applied. Reports from the tenacious people at
kernel bugzilla are also promising.
Considering that the punit access frequency with this patch is
considerably less, there is a possibility that this will push
the, still unknown, root cause past the triggering point on most loads.
But as we now can reliably reproduce the hang independently,
we can reduce the pain that users are having and use a
static thresholds until a root cause is found.
v3: don't break debugfs and simplification (Chris Wilson)
References: https://bugzilla.kernel.org/show_bug.cgi?id=109051
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: fritsch@xbmc.org
Cc: miku@iki.fi
Cc: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
CC: Michal Feix <michal@feix.cz>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Deepak S <deepak.s@linux.intel.com>
Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1487166779-26945-1-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit 6067a27d1f)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d595259fbb ]
This USB-SATA bridge chip is used in a StarTech enclosure for
optical drives.
Without the quirk MakeMKV fails during the key exchange with an
installed BluRay drive:
> Error 'Scsi error - ILLEGAL REQUEST:COPY PROTECTION KEY EXCHANGE FAILURE - KEY NOT ESTABLISHED'
> occurred while issuing SCSI command AD010..080002400 to device 'SG:dev_11:2'
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 71050ae7bf ]
Some Asus laptops that have an airplane-mode indicator LED, also have
the WMI WLAN user bit set, and the following bits in their DSDT:
Scope (_SB)
{
(...)
Device (ATKD)
{
(...)
Method (WMNB, 3, Serialized)
{
(...)
If (LEqual (IIA0, 0x00010002))
{
OWGD (IIA1)
Return (One)
}
}
}
}
So when asus-wmi uses ASUS_WMI_DEVID_WLAN_LED (0x00010002) to store the
wlan state, it drives the airplane-mode indicator LED (through the call
to OWGD) in an inverted fashion: the LED is ON when airplane mode is OFF
(since wlan is ON), and vice-versa.
This commit skips registering RFKill switches at all for these laptops,
to allow the asus-wireless driver to drive the airplane mode LED
correctly through the ASHS ACPI device. Relying on the presence of ASHS
and ASUS_WMI_DSTS_USER_BIT avoids adding DMI-based quirks for at least
21 different laptops.
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0b445549ea ]
In soft (no-reboot) mode, the driver self-pings watchdog upon expiration
of an interrupt. However the interrupt itself was not cleared thus on
first hit, the system enters infinite interrupt handling loop.
On Odroid U3 (Exynos4412), when booted with s3c2410_wdt.soft_noboot=1
argument the console is flooded:
# killall -9 watchdog
[ 60.523760] s3c2410-wdt 10060000.watchdog: watchdog timer expired (irq)
[ 60.536744] s3c2410-wdt 10060000.watchdog: watchdog timer expired (irq)
Fix this by writing something to the WTCLRINT register to clear the
interrupt. The register WTCLRINT however appeared in S3C6410 so a new
watchdog quirk and flavor are needed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 33be632b84 ]
The Qualcomm QDF2xxx root ports don't advertise an ACS capability, but they
do provide ACS-like features to disable peer transactions and validate bus
numbers in requests.
To be specific:
* Hardware supports source validation but it will report the issue as
Completer Abort instead of ACS Violation.
* Hardware doesn't support peer-to-peer and each root port is a root
complex with unique segment numbers.
* It is not possible for one root port to pass traffic to the other root
port. All PCIe transactions are terminated inside the root port.
Add an ACS quirk for the QDF2400 and QDF2432 products.
[bhelgaas: changelog]
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e9acc77dd0 ]
Initially all QorIQ platforms were PowerPC architecture and they didn't
support card detection except several platforms. The driver added the
quirk SDHCI_QUIRK_BROKEN_CARD_DETECTION as default and this made broken-cd
property in dts node didn't work. Now QorIQ platform turns to ARM
architecture and most of them could support card detection. However it's
a large number of dts trees that need to be fixed with broken-cd if we
remove the default SDHCI_QUIRK_BROKEN_CARD_DETECTION in driver. And the
users don't want to see this. So this patch is to remove this default
quirk just for ARM and keep it for PowerPC.(Note, QorIQ PowerPC platform
only has big-endian eSDHC while QorIQ ARM platform has big-endian or
little-endian eSDHC) This makes broken-cd property work again for ARM.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 72f2ff0deb ]
The PCIe Root Port in Hip06/Hip07 SoCs advertises an MSI capability, but it
cannot generate MSIs. It can transfer MSI/MSI-X from downstream devices,
but does not support MSI/MSI-X itself.
Add a quirk to prevent use of MSI/MSI-X by the Root Port.
[bhelgaas: changelog, sort vendor ID #define, drop device ID #define]
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ce709f8650 ]
The Broadcom Northstar2 SoC has a number of quirks for the PAXC
(internal/fake) PCI bus. Specifically, the PCI config space is shared
between the root port and the first PF (ie., PF0), and a number of fields
are tied to zero (thus preventing them from being set). These cannot be
"fixed" in device firmware, so we must fix them with a quirk.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3046ec674d ]
Commit 680a0873e1 ("arm: kernel: Add SMC structure parameter") added
a new "quirk" parameter to the SMC and HVC SMCCC backends, but only
updated the comment for the SMC version. This patch adds the new
paramater to the comment describing the HVC version too.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 82bcd08702 ]
This patch adds a Qualcomm specific quirk to the arm_smccc_smc call.
On Qualcomm ARM64 platforms, the SMC call can return before it has
completed. If this occurs, the call can be restarted, but it requires
using the returned session ID value from the interrupted SMC call.
The quirk stores off the session ID from the interrupted call in the
quirk structure so that it can be used by the caller.
This patch folds in a fix given by Sricharan R:
https://lkml.org/lkml/2016/9/28/272
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 680a0873e1 ]
This patch adds a quirk parameter to the arm_smccc_(smc/hvc) calls.
The quirk structure allows for specialized SMC operations due to SoC
specific requirements. The current arm_smccc_(smc/hvc) is renamed and
macros are used instead to specify the standard arm_smccc_(smc/hvc) or
the arm_smccc_(smc/hvc)_quirk function.
This patch and partial implementation was suggested by Will Deacon.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e7deb1570a ]
Non-generic devices have numbered_buttons set for both pen and
touch interfaces by default. The actual number of buttons on the
interface is normally manually decided later, which is different
from what those HID generic devices are processed, where number
of buttons are directly retrieved from HID descriptors.
This patch adds the missed HID_GENERIC check and moves the statement
to wacom_setup_pad_input_capabilities since it's not a quirk anymore.
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2ad6f30de7 ]
Some SoCs have a reset line that must be asserted/deasserted.
This patch adds a quirk to handle the new compatible
"allwinner,sun6i-a31-i2s" which will deassert the reset
line on probe function and assert it on remove's one.
This new compatible is useful in case of A33 codec driver, for example.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cbc00c1310 ]
In commit 821d6f0359 (ACPI / sleep: Do not save NVS for new machines to
accelerate S3), to optimize S3 suspend/resume speed, code is introduced
to ignore NVS memory saving during S3 for all the platforms later than
2012.
But, Lenovo G50-45, a platform released in 2015, still needs NVS memory
saving during S3. A quirk is introduced for this platform.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=189431
Tested-by: Przemek <soprwa@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
[ rjw: Drop unnecessary code ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a50477e55f ]
The existing code assumes a 19.2 MHz MCLK as the default
hardware configuration. This is valid for CherryTrail but
not for Baytrail.
Add explicit MCLK configuration to set the 19.2 clock on/off
depending on DAPM events.
This is a prerequisite step to enable devices with Baytrail
and RT5645 such as Asus X205TA
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 77e9a4aa9d ]
More and more platforms need the button.lid_init_state=open quirk. This
patch sets it the default behavior.
If a platform doesn't send lid open event or lid open event is lost due to
the underlying system problems, then we can compare various combinations:
1. systemd/acpid is used to suspend system or not, systemd has a special
logic forcing open event after resuming;
2. _LID returns a cached value or not.
The result is as follows:
1. lid_init_state=method
1. cached
1. resumed by lid:
(x) event=close
(x) systemd=suspends again
(x) acpid=suspends again
(x) state=close
2. resumed by other:
(o) event=close
(x) systemd=suspends again
(x) acpid=suspends again
(o) state=close
2. non-cached
1. resumed by lid:
(o) event=open
(o) systemd=resumes
(o) acpid=resumes
(o) state=open
2. resumed by other:
(o) event=close
(x) systemd=suspends again
(x) acpid=suspends again
(o) state=close
2. lid_init_state=open
1. cached
1. resumed by lid:
(o) event=open
(o) systemd=resumes
(o) acpid=resumes
(x) state=close
2. resumed by other:
(x) event=open
(o) systemd=resumes
(o) acpid=resumes
(o) state=close
2. non-cached
1. resumed by lid:
(o) event=open
(o) systemd=resumes
(o) acpid=resumes
(o) state=open
2. resumed by other:
(x) event=open
(o) systemd=resumes
(o) acpid=resumes
(o) state=close
3. lid_init_state=ignore
1. cached
1. resumed by lid:
(o) event=none
(x) systemd=suspends again
(o) acpid=resumes
(x) state=close
2. resumed by other:
(o) event=none
(x) systemd=suspends again
(o) acpid=resumes
(o) state=close
2. non-cached
1. resumed by lid:
(o) event=none
(x) systemd=suspends again
(o) acpid=resumes
(o) state=open
2. resumed by other:
(o) event=none
(x) systemd=suspends again
(o) acpid=resumes
(o) state=close
As a conclusion:
1. With systemd changed, lid_init_state=ignore has only one problem and the
problem comes from an underlying issue, not userspace and kernel lid
handling.
2. Without systemd changed, lid_init_state=open can be the default
behavior as the pass ratio is not much worse than lid_init_state=ignore.
3. lid_init_state=method is buggy, we can have a separate patch to make it
deprectated.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=187271
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f4d435f326 ]
There's an issue with the da850 SATA controller: if port multiplier
support is compiled in, but we're connecting the drive directly to
the SATA port on the board, the drive can't be detected.
To make SATA work on the da850-lcdk board: first try to softreset
with pmp - if the operation fails with -EBUSY, retry without pmp.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1ded56df32 ]
The "port" variable was allocated with devm_kzalloc() so if we free it with
kfree() it will be freed twice. Also I changed it to propogate the error
from devm_ioremap_resource() instead of returning -ENOMEM.
Fixes: c5d4603961 ("PCI: Add MCFG quirks for X-Gene host controller")
Also-posted-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Tanmay Inamdar <tinamdar@apm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7184f5b451 ]
Intel 200-series chipsets have the same errata as 100-series: the ACS
capability doesn't follow the PCIe spec, the capability and control
registers are dwords rather than words. Add PCIe root port device IDs to
existing quirk.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e42a5dbb8a ]
dwc3 revisions <=3.00a have a limitation where Port Disable command
doesn't work. Set the quirk-broken-port-ped property for such
controllers so XHCI core can do the necessary workaround.
[rogerq@ti.com] Updated code from platform data to device property.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 41135de1e7 ]
Some devices from Texas Instruments [1] suffer from
a silicon bug where Port Enabled/Disabled bit
should not be used to silence an erroneous device.
The bug is so that if port is disabled with PED
bit, an IRQ for device removal (or attachment)
will never fire.
Just for the sake of completeness, the actual
problem lies with SNPS USB IP and this affects
all known versions up to 3.00a. A separate
patch will be added to dwc3 to enabled this
quirk flag if version is <= 3.00a.
[1] - AM572x Silicon Errata http://www.ti.com/lit/er/sprz429j/sprz429j.pdf
Section i896— USB xHCI Port Disable Feature Does Not Work
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b6ffcf2108 ]
UART uses as EDMA as dma engine on AM437x SoC and therefore, requires
OMAP_DMA_TX_KICK quirk just like AM33xx. So, enable OMAP_DMA_TX_KICK
quirk for AM437x platform as well. While at that, drop use of
of_machine_is_compatible() and instead pass quirks via device data.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dd3749099c ]
The core framework already handles setting this parameter with a
platform quirk. Add the appropriate flag so that we always set
AHBBURST to 0. Technically DT should be doing this, but we always
do it for msm chipidea devices so setting the flag in the driver
works just as well. If the burst needs to be anything besides 0,
we expect the 'ahb-burst-config' dts property to be present.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 98b2f01c8d ]
Back in 2014, commit fb7023e0e2 ("drm/i915: BDW: Adding Reserved PCI
IDs.") added the reserved PCI IDs in order to try to make sure we had
working drivers in case we ever released products using these IDs
(since we had instances of this type of problem in the past). The
problem is that the patch only touched the macros used by
early-quirks.c and by the user space components that rely on
i915_pciids.h, it didn't touch the macros used by i915_pci.c. So we
correctly handled the stolen memory for these theoretical IDs, but we
didn't actually drive the devices from i915.ko.
So this patch fixes the original commit by actually making i915.ko
drive these IDs, which was the goal. There's no information on what
would be the GT count on these IDs, so we just go with the safer
intel_broadwell_info, at the risk of ignoring a possibly inexistent
BSD2_RING.
I did some checking, and it seems that these IDs are driven by
intel-gpu-tools, xf86-video-intel and libdrm (since they contain old
copies of i915_pciids.h), but they are not checked by mesa.
The alternative to this patch would be to just assume we're actually
never going to use these IDs, and then remove them from our ID lists
and make sure our user space components sync the latest i915_pciids.h
copy. I'm fine with either approaches, as long as we make sure that
every component tries to drive the same list of PCI IDs.
Fixes: fb7023e0e2 ("drm/i915: BDW: Adding Reserved PCI IDs.")
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1483473860-17644-3-git-send-email-paulo.r.zanoni@intel.com
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 06ce521af9 upstream.
handle_vmon gets a reference on VMXON region page,
but does not release it. Release the reference.
Found by syzkaller; based on a patch by Dmitry.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Charles (Chas) Williams" <ciwillia@brocade.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f5b98461cb upstream.
Now that our crng uses chacha20, we can rely on its speedy
characteristics for replacing MD5, while simultaneously achieving a
higher security guarantee. Before the idea was to use these functions if
you wanted random integers that aren't stupidly insecure but aren't
necessarily secure either, a vague gray zone, that hopefully was "good
enough" for its users. With chacha20, we can strengthen this claim,
since either we're using an rdrand-like instruction, or we're using the
same crng as /dev/urandom. And it's faster than what was before.
We could have chosen to replace this with a SipHash-derived function,
which might be slightly faster, but at the cost of having yet another
RNG construction in the kernel. By moving to chacha20, we have a single
RNG to analyze and verify, and we also already get good performance
improvements on all platforms.
Implementation-wise, rather than use a generic buffer for both
get_random_int/long and memcpy based on the size needs, we use a
specific buffer for 32-bit reads and for 64-bit reads. This way, we're
guaranteed to always have aligned accesses on all platforms. While
slightly more verbose in C, the assembly this generates is a lot
simpler than otherwise.
Finally, on 32-bit platforms where longs and ints are the same size,
we simply alias get_random_int to get_random_long.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Suggested-by: Theodore Ts'o <tytso@mit.edu>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cf01fb9985 upstream.
In the case that compat_get_bitmap fails we do not want to copy the
bitmap to the user as it will contain uninitialized stack data and leak
sensitive data.
Signed-off-by: Chris Salls <salls@cs.ucsb.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cf903e9d3a upstream.
A patch documenting how to specify which kernels a particular fix should
be backported to (seemingly) inadvertently added a minus sign after the
kernel version. This particular stable-tag format had never been used
prior to this patch, and was neither present when the patch in question
was first submitted (it was added in v2 without any comment).
Drop the minus sign to avoid any confusion.
Fixes: fdc81b7910 ("stable_kernel_rules: Add clause about specification of kernel versions to patch.")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit de288e36fe upstream.
In the case of bounced ep0 requests, we must delay DMA operation until
after ->complete() otherwise we might overwrite contents of req->buf.
This caused problems with RNDIS gadget.
Signed-off-by: Janusz Dziedzic <januszx.dziedzic@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2958b9013f upstream.
Fix to correctly assign 1ms for gvt scheduler interval time,
as previous code using HZ is pretty broken. And use no delay
for start gvt scheduler function.
Fixes: 4b63960ebd ("drm/i915/gvt: vGPU schedule policy framework")
Cc: Zhi Wang <zhi.a.wang@intel.com>
Acked-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0115f6cbf2 upstream.
On VTLB+FTLB platforms (such as Loongson-3A R2), FTLB's pagesize is
usually configured the same as PAGE_SIZE. In such a case, Huge page
entry is not suitable to write in FTLB.
Unfortunately, when a huge page is created, its page table entries
haven't created immediately. Then the TLB refill handler will fetch an
invalid page table entry which has no "HUGE" bit, and this entry may be
written to FTLB. Since it is invalid, TLB load/store handler will then
use tlbwi to write the valid entry at the same place. However, the
valid entry is a huge page entry which isn't suitable for FTLB.
Our solution is to modify build_huge_handler_tail. Flush the invalid
old entry (whether it is in FTLB or VTLB, this is in order to reduce
branches) and use tlbwr to write the valid new entry.
Signed-off-by: Rui Wang <wangr@lemote.com>
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J . Hill <Steven.Hill@caviumnetworks.com>
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15754/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5a34133167 upstream.
Loongson-3's micro TLB (ITLB) is not strictly a subset of JTLB. That
means: when a JTLB entry is replaced by hardware, there may be an old
valid entry exists in ITLB. So, a TLB miss exception may occur while
handle_ri_rdhwr() is running because it try to access EPC's content.
However, handle_ri_rdhwr() doesn't clear EXL, which makes a TLB Refill
exception be treated as a TLB Invalid exception and tlbp may fail. In
this case, if FTLB (which is usually set-associative instead of set-
associative) is enabled, a tlbp failure will cause an invalid tlbwi,
which will hang the whole system.
This patch rename handle_ri_rdhwr_vivt to handle_ri_rdhwr_tlbp and use
it for Loongson-3. It try to solve the same problem described as below,
but more straightforwards.
https://patchwork.linux-mips.org/patch/12591/
I think Loongson-2 has the same problem, but it has no FTLB, so we just
keep it as is.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: Rui Wang <wangr@lemote.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J . Hill <Steven.Hill@caviumnetworks.com>
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15753/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4b5347a24a upstream.
When building for microMIPS we need to ensure that the assembler always
knows that there is code at the target of a branch or jump. Recent
toolchains will fail to link a microMIPS kernel when this isn't the case
due to what it thinks is a branch to non-microMIPS code.
mips-mti-linux-gnu-ld kernel/built-in.o: .spinlock.text+0x2fc: Unsupported branch between ISA modes.
mips-mti-linux-gnu-ld final link failed: Bad value
This is due to inline assembly labels in spinlock.h not being followed
by an instruction mnemonic, either due to a .subsection pseudo-op or the
end of the inline asm block.
Fix this with a .insn direction after such labels.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/15325/
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e6c774773 upstream.
When a 32-bit kernel is configured to support MIPS64r6 (CPU_MIPS64_R6),
MIPS_O32_FP64_SUPPORT won't be selected as it should be because
MIPS32_O32 is disabled (o32 is already the default ABI available on
32-bit kernels).
This results in userland FP breakage as CP0_Status.FR is read-only 1
since r6 (when an FPU is present) so __enable_fpu() will fail to clear
FR. This causes the FPU emulator to get used which will incorrectly
emulate 32-bit FPU registers.
Force o32 fp64 support in this case by also selecting
MIPS_O32_FP64_SUPPORT from CPU_MIPS64_R6 if 32BIT.
Fixes: 4e9d324d42 ("MIPS: Require O32 FP64 support for MIPS64 with O32 compat")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15310/
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d09c5373e8 upstream.
Commit fd2d2b191f ("s390: get_user() should zero on failure")
intended to fix s390's get_user() implementation which did not zero
the target operand if the read from user space faulted. Unfortunately
the patch has no effect: the corresponding inline assembly specifies
that the operand is only written to ("=") and the previous value is
discarded.
Therefore the compiler is free to and actually does omit the zero
initialization.
To fix this simply change the contraint modifier to "+", so the
compiler cannot omit the initialization anymore.
Fixes: c9ca78415a ("s390/uaccess: provide inline variants of get_user/put_user")
Fixes: fd2d2b191f ("s390: get_user() should zero on failure")
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d82c0d12c9 upstream.
Reorder the operations in decompress_kernel() to ensure initrd is moved
to a safe location before the bss section is zeroed.
During decompression bss can overlap with the initrd and this can
corrupt the initrd contents depending on the size of the compressed
kernel (which affects where the initrd is placed by the bootloader) and
the size of the bss section of the decompressor.
Also use the correct initrd size when checking for overlaps with
parmblock.
Fixes: 06c0dd72ae ([S390] fix boot failures with compressed kernels)
Reviewed-by: Joy Latten <joy.latten@canonical.com>
Reviewed-by: Vineetha HariPai <vineetha.hari.pai@canonical.com>
Signed-off-by: Marcelo Henrique Cerri <marcelo.cerri@canonical.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b83878dd7 upstream.
When __pa is applied to virtual address in uncached KSEG region the
result is incorrect. Fix it by checking if the original address is in
the uncached KSEG and adjusting the result. It looks better than masking
off bits because pfn_valid would correctly work with new __pa results
and it may be made working in noMMU case, once we get definition for
uncached memory view.
This is required for the dma_common_mmap and DMA debug code to work
correctly: they both indirectly use __pa with coherent DMA addresses.
In case of DMA debug the visible effect is false reports that an address
mapped for DMA is accessed by CPU.
Tested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 921d701e6f upstream.
Make sure to reserve the boot memory for the flattened device tree.
Otherwise it might get overwritten, e.g. when initial_boot_params is
copied, leading to a corrupted FDT and a boot hang/crash:
bootconsole [early0] enabled
Early console on uart16650 initialized at 0xf8001600
OF: fdt: Error -11 processing FDT
Kernel panic - not syncing: setup_cpuinfo: No CPU found in devicetree!
---[ end Kernel panic - not syncing: setup_cpuinfo: No CPU found in devicetree!
Guenter Roeck says:
> I think I found the problem. In unflatten_and_copy_device_tree(), with added
> debug information:
>
> OF: fdt: initial_boot_params=c861e400, dt=c861f000 size=28874 (0x70ca)
>
> ... and then initial_boot_params is copied to dt, which results in corrupted
> fdt since the memory overlaps. Looks like the initial_boot_params memory
> is not reserved and (re-)allocated by early_init_dt_alloc_memory_arch().
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reference: http://lkml.kernel.org/r/20170226210338.GA19476@roeck-us.net
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4749228f02 upstream.
In crc32c_vpmsum() we call enable_kernel_altivec() without first
disabling preemption, which is not allowed:
WARNING: CPU: 9 PID: 2949 at ../arch/powerpc/kernel/process.c:277 enable_kernel_altivec+0x100/0x120
Modules linked in: dm_thin_pool dm_persistent_data dm_bio_prison dm_bufio libcrc32c vmx_crypto ...
CPU: 9 PID: 2949 Comm: docker Not tainted 4.11.0-rc5-compiler_gcc-6.3.1-00033-g308ac7563944 #381
...
NIP [c00000000001e320] enable_kernel_altivec+0x100/0x120
LR [d000000003df0910] crc32c_vpmsum+0x108/0x150 [crc32c_vpmsum]
Call Trace:
0xc138fd09 (unreliable)
crc32c_vpmsum+0x108/0x150 [crc32c_vpmsum]
crc32c_vpmsum_update+0x3c/0x60 [crc32c_vpmsum]
crypto_shash_update+0x88/0x1c0
crc32c+0x64/0x90 [libcrc32c]
dm_bm_checksum+0x48/0x80 [dm_persistent_data]
sb_check+0x84/0x120 [dm_thin_pool]
dm_bm_validate_buffer.isra.0+0xc0/0x1b0 [dm_persistent_data]
dm_bm_read_lock+0x80/0xf0 [dm_persistent_data]
__create_persistent_data_objects+0x16c/0x810 [dm_thin_pool]
dm_pool_metadata_open+0xb0/0x1a0 [dm_thin_pool]
pool_ctr+0x4cc/0xb60 [dm_thin_pool]
dm_table_add_target+0x16c/0x3c0
table_load+0x184/0x400
ctl_ioctl+0x2f0/0x560
dm_ctl_ioctl+0x38/0x50
do_vfs_ioctl+0xd8/0x920
SyS_ioctl+0x68/0xc0
system_call+0x38/0xfc
It used to be sufficient just to call pagefault_disable(), because that
also disabled preemption. But the two were decoupled in commit 8222dbe21e
("sched/preempt, mm/fault: Decouple preemption from the page fault
logic") in mid 2015.
So add the missing preempt_disable/enable(). We should also call
disable_kernel_fp(), although it does nothing by default, there is a
debug switch to make it active and all enables should be paired with
disables.
Fixes: 6dd7a82cc5 ("crypto: powerpc - Add POWER8 optimised crc32c")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 48fe9e9488 upstream.
In the past, there was only one load-with-reservation instruction,
lwarx, and if a program attempted a lwarx on a misaligned address, it
would take an alignment interrupt and the kernel handler would emulate
it as though it was lwzx, which was not really correct, but benign since
it is loading the right amount of data, and the lwarx should be paired
with a stwcx. to the same address, which would also cause an alignment
interrupt which would result in a SIGBUS being delivered to the process.
We now have 5 different sizes of load-with-reservation instruction. Of
those, lharx and ldarx cause an immediate SIGBUS by luck since their
entries in aligninfo[] overlap instructions which were not fixed up, but
lqarx overlaps with lhz and will be emulated as such. lbarx can never
generate an alignment interrupt since it only operates on 1 byte.
To straighten this out and fix the lqarx case, this adds code to detect
the l[hwdq]arx instructions and return without fixing them up, resulting
in a SIGBUS being delivered to the process.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f5f525d5b upstream.
When the kernel is compiled to use 64bit ABIv2 the _GLOBAL() macro does
not include a global entry point. A function's global entry point is
used when the function is called from a different TOC context and in the
kernel this typically means a call from a module into the vmlinux (or
vice-versa).
There are a few exported asm functions declared with _GLOBAL() and
calling them from a module will likely crash the kernel since any TOC
relative load will yield garbage.
flush_icache_range() and flush_dcache_range() are both exported to
modules, and use the TOC, so must use _GLOBAL_TOC().
Fixes: 721aeaa9fd ("powerpc: Build little endian ppc64 kernel with ABIv2")
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 88b1bf7268 upstream.
Commit 4c6d9acce1 ("powerpc/mm: Add hooks for cxl") converted local
TLB invalidates to global if the cxl driver is active. This is necessary
because the CAPP snoops invalidations to forward them to the PSL on the
cxl adapter. However one path was forgotten. native_flush_hash_range()
still does local TLB invalidates, as found out the hard way recently.
This patch fixes it by following the same logic as previously: if the
cxl driver is active, the local TLB invalidates are 'upgraded' to
global.
Fixes: 4c6d9acce1 ("powerpc/mm: Add hooks for cxl")
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ed23e1bae upstream.
On Power8 & Power9 the early CPU inititialisation in __init_HFSCR()
turns on HFSCR[TM] (Hypervisor Facility Status and Control Register
[Transactional Memory]), but that doesn't take into account that TM
might be disabled by CPU features, or disabled by the kernel being built
with CONFIG_PPC_TRANSACTIONAL_MEM=n.
So later in boot, when we have setup the CPU features, clear HSCR[TM] if
the TM CPU feature has been disabled. We use CPU_FTR_TM_COMP to account
for the CONFIG_PPC_TRANSACTIONAL_MEM=n case.
Without this a KVM guest might try use TM, even if told not to, and
cause an oops in the host kernel. Typically the oops is seen in
__kvmppc_vcore_entry() and may or may not be fatal to the host, but is
always bad news.
In practice all shipping CPU revisions do support TM, and all host
kernels we are aware of build with TM support enabled, so no one should
actually be able to hit this in the wild.
Fixes: 2a3563b023 ("powerpc: Setup in HFSCR for POWER8")
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
[mpe: Rewrite change log with input from Sam, add Fixes/stable]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 280489daa6 upstream.
The newly added a5xx support fails to build when debugfs is diabled:
drivers/gpu/drm/msm/adreno/a5xx_gpu.c:849:4: error: 'struct msm_gpu_funcs' has no member named 'show'
drivers/gpu/drm/msm/adreno/a5xx_gpu.c:849:11: error: 'a5xx_show' undeclared here (not in a function); did you mean 'a5xx_irq'?
This adds a missing #ifdef.
Fixes: b5f103ab98 ("drm/msm: gpu: Add A5XX target support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b884a190af upstream.
The rapf copy loops in the Meta usercopy code is missing some extable
entries for HTP cores with unaligned access checking enabled, where
faults occur on the instruction immediately after the faulting access.
Add the fixup labels and extable entries for these cases so that corner
case user copy failures don't cause kernel crashes.
Fixes: 373cd784d0 ("metag: Memory handling")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-metag@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c0b1df88b upstream.
The fixup code to rewind the source pointer in
__asm_copy_from_user_{32,64}bit_rapf_loop() always rewound the source by
a single unit (4 or 8 bytes), however this is insufficient if the fault
didn't occur on the first load in the loop, as the source pointer will
have been incremented but nothing will have been stored until all 4
register [pairs] are loaded.
Read the LSM_STEP field of TXSTATUS (which is already loaded into a
register), a bit like the copy_to_user versions, to determine how many
iterations of MGET[DL] have taken place, all of which need rewinding.
Fixes: 373cd784d0 ("metag: Memory handling")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-metag@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fd40eee129 upstream.
The fixup code for the copy_to_user rapf loops reads TXStatus.LSM_STEP
to decide how far to rewind the source pointer. There is a special case
for the last execution of an MGETL/MGETD, since it leaves LSM_STEP=0
even though the number of MGETLs/MGETDs attempted was 4. This uses ADDZ
which is conditional upon the Z condition flag, but the AND instruction
which masked the TXStatus.LSM_STEP field didn't set the condition flags
based on the result.
Fix that now by using ANDS which does set the flags, and also marking
the condition codes as clobbered by the inline assembly.
Fixes: 373cd784d0 ("metag: Memory handling")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-metag@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 563ddc1076 upstream.
Currently we try to zero the destination for a failed read from userland
in fixup code in the usercopy.c macros. The rest of the destination
buffer is then zeroed from __copy_user_zeroing(), which is used for both
copy_from_user() and __copy_from_user().
Unfortunately we fail to zero in the fixup code as D1Ar1 is set to 0
before the fixup code entry labels, and __copy_from_user() shouldn't even
be zeroing the rest of the buffer.
Move the zeroing out into copy_from_user() and rename
__copy_user_zeroing() to raw_copy_from_user() since it no longer does
any zeroing. This also conveniently matches the name needed for
RAW_COPY_USER support in a later patch.
Fixes: 373cd784d0 ("metag: Memory handling")
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-metag@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb8ea062a8 upstream.
When copying to userland on Meta, if any faults are encountered
immediately abort the copy instead of continuing on and repeatedly
faulting, and worse potentially copying further bytes successfully to
subsequent valid pages.
Fixes: 373cd784d0 ("metag: Memory handling")
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-metag@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2257211942 upstream.
Fix the error checking of the alignment adjustment code in
raw_copy_from_user(), which mistakenly considers it safe to skip the
error check when aligning the source buffer on a 2 or 4 byte boundary.
If the destination buffer was unaligned it may have started to copy
using byte or word accesses, which could well be at the start of a new
(valid) source page. This would result in it appearing to have copied 1
or 2 bytes at the end of the first (invalid) page rather than none at
all.
Fixes: 373cd784d0 ("metag: Memory handling")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-metag@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d77facb884 upstream.
A use-after-free was found using KASAN. In brcmf_p2p_del_if() the virtual
interface is removed using call to brcmf_remove_interface(). After that
the virtual interface instance has been freed and should not be referenced.
Solve this by storing the nl80211 iftype in local variable, which is used
in a couple of places anyway.
Reported-by: Daniel J Blueman <daniel@quora.org>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d65f82954 upstream.
When internal mac80211 TXQs aren't supported, netdev queues must
always started out started even when driver queues are stopped
while the interface is added. This is necessary because with the
internal TXQ support netdev queues are never stopped and packet
scheduling/dropping is done in mac80211.
Fixes: 80a83cfc43 ("mac80211: skip netdev queue control with software queuing")
Reported-and-tested-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3dd09d5a85 upstream.
When punching past EOF on XFS, fallocate(mode=PUNCH_HOLE|KEEP_SIZE) will
round the file size up to the nearest multiple of PAGE_SIZE:
calvinow@vm-disks/generic-xfs-1 ~$ dd if=/dev/urandom of=test bs=2048 count=1
calvinow@vm-disks/generic-xfs-1 ~$ stat test
Size: 2048 Blocks: 8 IO Block: 4096 regular file
calvinow@vm-disks/generic-xfs-1 ~$ fallocate -n -l 2048 -o 2048 -p test
calvinow@vm-disks/generic-xfs-1 ~$ stat test
Size: 4096 Blocks: 8 IO Block: 4096 regular file
Commit 3c2bdc912a ("xfs: kill xfs_zero_remaining_bytes") replaced
xfs_zero_remaining_bytes() with calls to iomap helpers. The new helpers
don't enforce that [pos,offset) lies strictly on [0,i_size) when being
called from xfs_free_file_space(), so by "leaking" these ranges into
xfs_zero_range() we get this buggy behavior.
Fix this by reintroducing the checks xfs_zero_remaining_bytes() did
against i_size at the bottom of xfs_free_file_space().
Reported-by: Aaron Gao <gzh@fb.com>
Fixes: 3c2bdc912a ("xfs: kill xfs_zero_remaining_bytes")
Cc: Christoph Hellwig <hch@lst.de>
Cc: Brian Foster <bfoster@redhat.com>
Signed-off-by: Calvin Owens <calvinowens@fb.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cefdc26e86 upstream.
Without this fix (and another to the userspace component itself
described later), the kernel will be unable to process any OrangeFS
requests after the userspace component is restarted (due to a crash or
at the administrator's behest).
The bug here is that inside orangefs_remount, the orangefs_request_mutex
is locked. When the userspace component restarts while the filesystem
is mounted, it sends a ORANGEFS_DEV_REMOUNT_ALL ioctl to the device,
which causes the kernel to send it a few requests aimed at synchronizing
the state between the two. While this is happening the
orangefs_request_mutex is locked to prevent any other requests going
through.
This is only half of the bugfix. The other half is in the userspace
component which outright ignores(!) requests made before it considers
the filesystem remounted, which is after the ioctl returns. Of course
the ioctl doesn't return until after the userspace component responds to
the request it ignores. The userspace component has been changed to
allow ORANGEFS_VFS_OP_FEATURES regardless of the mount status.
Mike Marshall says:
"I've tested this patch against the fixed userspace part. This patch is
real important, I hope it can make it into 4.11...
Here's what happens when the userspace daemon is restarted, without
the patch:
=============================================
[ INFO: possible recursive locking detected ]
[ 4.10.0-00007-ge98bdb3 #1 Not tainted ]
---------------------------------------------
pvfs2-client-co/29032 is trying to acquire lock:
(orangefs_request_mutex){+.+.+.}, at: service_operation+0x3c7/0x7b0 [orangefs]
but task is already holding lock:
(orangefs_request_mutex){+.+.+.}, at: dispatch_ioctl_command+0x1bf/0x330 [orangefs]
CPU: 0 PID: 29032 Comm: pvfs2-client-co Not tainted 4.10.0-00007-ge98bdb3 #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.9.3-1.fc25 04/01/2014
Call Trace:
__lock_acquire+0x7eb/0x1290
lock_acquire+0xe8/0x1d0
mutex_lock_killable_nested+0x6f/0x6e0
service_operation+0x3c7/0x7b0 [orangefs]
orangefs_remount+0xea/0x150 [orangefs]
dispatch_ioctl_command+0x227/0x330 [orangefs]
orangefs_devreq_ioctl+0x29/0x70 [orangefs]
do_vfs_ioctl+0xa3/0x6e0
SyS_ioctl+0x79/0x90"
Signed-off-by: Martin Brandenburg <martin@omnibond.com>
Acked-by: Mike Marshall <hubcap@omnibond.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7292ae3d5a upstream.
The latest change of asm goto support check added passing of KBUILD_CFLAGS
to compiler. When these flags reference gcc plugins that are not built yet,
the check fails.
When one runs "make bzImage" followed by "make modules", the kernel is always
built with HAVE_JUMP_LABEL disabled, while the modules are built depending on
CONFIG_JUMP_LABEL. If HAVE_JUMP_LABEL macro happens to be different, modules
are built with undefined references, e.g.:
ERROR: "static_key_slow_inc" [net/netfilter/xt_TEE.ko] undefined!
ERROR: "static_key_slow_dec" [net/netfilter/xt_TEE.ko] undefined!
ERROR: "static_key_slow_dec" [net/netfilter/nft_meta.ko] undefined!
ERROR: "static_key_slow_inc" [net/netfilter/nft_meta.ko] undefined!
ERROR: "nf_hooks_needed" [net/netfilter/ipvs/ip_vs.ko] undefined!
ERROR: "nf_hooks_needed" [net/ipv6/ipv6.ko] undefined!
ERROR: "static_key_count" [net/ipv6/ipv6.ko] undefined!
ERROR: "static_key_slow_inc" [net/ipv6/ipv6.ko] undefined!
This change moves the check before all these references are added
to KBUILD_CFLAGS. This is correct because subsequent KBUILD_CFLAGS
modifications are not relevant to this check.
Reported-by: Anton V. Boyarshinov <boyarsh@altlinux.org>
Fixes: 35f860f9ba ("jump label: pass kbuild_cflags when checking for asm goto support")
Signed-off-by: Gleb Fotengauer-Malinovskiy <glebfm@altlinux.org>
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Acked-by: David Lin <dtwlin@google.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b334e19ae9 upstream.
In commit a76bcf557e ("Kbuild: enable -Wmaybe-uninitialized warning
for "make W=1""), I reverted another change that happened to fix a problem
with old compilers, and now we get this report again with old compilers
(prior to gcc-4.8) and GCOV enabled:
cc1: warnings being treated as errors
drivers/gpu/drm/i915/intel_ringbuffer.c: In function 'intel_ring_setup_status_page':
drivers/gpu/drm/i915/intel_ringbuffer.c:438: error: 'mmio.reg' may be used uninitialized in this function
At top level:
>> cc1: error: unrecognized command line option "-Wno-maybe-uninitialized"
The problem is that we turn off the warning conditionally in a number
of places as we should, but one of them does it unconditionally.
Instead, change it to call cc-disable-warning as we do elsewhere.
The original patch that caused it was merged into linux-4.7, then
4.8 removed the change and 4.9 brought it back, so we probably want
a backport to 4.9 once this is merged.
Use a ':=' assignment instead of '=' to force the cc-disable-warning
call to only be evaluated once instead of every time.
Fixes: a76bcf557e ("Kbuild: enable -Wmaybe-uninitialized warning for "make W=1"")
Fixes: e72e2dfe7c ("gcov: disable -Wmaybe-uninitialized warning")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fdad4e7a87 upstream.
Commit c2a6bbaf0c (ACPI / scan: Prefer devices without _HID/_CID
for _ADR matching) added a list_empty(&adev->pnp.ids) check to
find_child_checks() so as to catch situations in which the ACPI
core attempts to decode _ADR for a device having a _HID too which
is strictly against the spec. However, it overlooked the fact that
the adev->pnp.ids list for the devices taken into account by
find_child_checks() may contain device IDs set internally by the
kernel, like "LNXVIDEO" (thanks to Zhang Rui for that realization),
and it broke the enumeration of those devices as a result.
To unbreak it, replace the overly coarse grained list_empty()
check with a much more precise check against the pnp.type.platform_id
flag which is only set for devices having a _HID (that's how it
should be done from the start, as having both _ADR and _CID is
actually permitted).
Fixes: c2a6bbaf0c (ACPI / scan: Prefer devices without _HID/_CID for _ADR matching)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=194889
Reported-and-tested-by: Mike <mike@mikewilson.me.uk>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f1a880a93b upstream.
If the hash tree itself is sufficiently corrupt in addition to data blocks,
it's possible for error correction to end up in a deep recursive loop,
which eventually causes a kernel panic. This change limits the
recursion to a reasonable level during a single I/O operation.
Fixes: a739ff3f54 ("dm verity: add support for forward error correction")
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e11f8b7b6c upstream.
While running generic/340 in my test setup I hit the following race. It
can happen with kernels that support FS DAX PMDs, so v4.10 thru
v4.11-rc5.
Thread 1 Thread 2
-------- --------
dax_iomap_pmd_fault()
grab_mapping_entry()
spin_lock_irq()
get_unlocked_mapping_entry()
'entry' is NULL, can't call lock_slot()
spin_unlock_irq()
radix_tree_preload()
dax_iomap_pmd_fault()
grab_mapping_entry()
spin_lock_irq()
get_unlocked_mapping_entry()
...
lock_slot()
spin_unlock_irq()
dax_pmd_insert_mapping()
<inserts a PMD mapping>
spin_lock_irq()
__radix_tree_insert() fails with -EEXIST
<fall back to 4k fault, and die horribly
when inserting a 4k entry where a PMD exists>
The issue is that we have to drop mapping->tree_lock while calling
radix_tree_preload(), but since we didn't have a radix tree entry to
lock (unlike in the pmd_downgrade case) we have no protection against
Thread 2 coming along and inserting a PMD at the same index. For 4k
entries we handled this with a special-case response to -EEXIST coming
from the __radix_tree_insert(), but this doesn't save us for PMDs
because the -EEXIST case can also mean that we collided with a 4k entry
in the radix tree at a different index, but one that is covered by our
PMD range.
So, correctly handle both the 4k and 2M collision cases by explicitly
re-checking the radix tree for an entry at our index once we reacquire
mapping->tree_lock.
This patch has made it through a clean xfstests run with the current
v4.11-rc5 based linux/master, and it also ran generic/340 500 times in a
loop. It used to fail within the first 10 iterations.
Link: http://lkml.kernel.org/r/20170406212944.2866-1-ross.zwisler@linux.intel.com
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: "Darrick J. Wong" <darrick.wong@oracle.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5402e97af6 upstream.
In PT_SEIZED + LISTEN mode STOP/CONT signals cause a wakeup against
__TASK_TRACED. If this races with the ptrace_unfreeze_traced at the end
of a PTRACE_LISTEN, this can wake the task /after/ the check against
__TASK_TRACED, but before the reset of state to TASK_TRACED. This
causes it to instead clobber TASK_WAKING, allowing a subsequent wakeup
against TRACED while the task is still on the rq wake_list, corrupting
it.
Oleg said:
"The kernel can crash or this can lead to other hard-to-debug problems.
In short, "task->state = TASK_TRACED" in ptrace_unfreeze_traced()
assumes that nobody else can wake it up, but PTRACE_LISTEN breaks the
contract. Obviusly it is very wrong to manipulate task->state if this
task is already running, or WAKING, or it sleeps again"
[akpm@linux-foundation.org: coding-style fixes]
Fixes: 9899d11f ("ptrace: ensure arch_ptrace/ptrace_request can never race with SIGKILL")
Link: http://lkml.kernel.org/r/xm26y3vfhmkp.fsf_-_@bsegall-linux.mtv.corp.google.com
Signed-off-by: Ben Segall <bsegall@google.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b3ef5520c1 upstream.
We got the following use-after-free KASAN report:
BUG: KASAN: use-after-free in wiphy_resume+0x591/0x5a0 [cfg80211]
at addr ffff8803fc244090
Read of size 8 by task kworker/u16:24/2587
CPU: 6 PID: 2587 Comm: kworker/u16:24 Tainted: G B 4.9.13-debug+
Hardware name: Dell Inc. XPS 15 9550/0N7TVV, BIOS 1.2.19 12/22/2016
Workqueue: events_unbound async_run_entry_fn
ffff880425d4f9d8 ffffffffaeedb541 ffff88042b80ef00 ffff8803fc244088
ffff880425d4fa00 ffffffffae84d7a1 ffff880425d4fa98 ffff8803fc244080
ffff88042b80ef00 ffff880425d4fa88 ffffffffae84da3a ffffffffc141f7d9
Call Trace:
[<ffffffffaeedb541>] dump_stack+0x85/0xc4
[<ffffffffae84d7a1>] kasan_object_err+0x21/0x70
[<ffffffffae84da3a>] kasan_report_error+0x1fa/0x500
[<ffffffffc141f7d9>] ? cfg80211_bss_age+0x39/0xc0 [cfg80211]
[<ffffffffc141f83a>] ? cfg80211_bss_age+0x9a/0xc0 [cfg80211]
[<ffffffffae48d46d>] ? trace_hardirqs_on+0xd/0x10
[<ffffffffc13fb1c0>] ? wiphy_suspend+0xc70/0xc70 [cfg80211]
[<ffffffffae84def1>] __asan_report_load8_noabort+0x61/0x70
[<ffffffffc13fb100>] ? wiphy_suspend+0xbb0/0xc70 [cfg80211]
[<ffffffffc13fb751>] ? wiphy_resume+0x591/0x5a0 [cfg80211]
[<ffffffffc13fb751>] wiphy_resume+0x591/0x5a0 [cfg80211]
[<ffffffffc13fb1c0>] ? wiphy_suspend+0xc70/0xc70 [cfg80211]
[<ffffffffaf3b206e>] dpm_run_callback+0x6e/0x4f0
[<ffffffffaf3b31b2>] device_resume+0x1c2/0x670
[<ffffffffaf3b367d>] async_resume+0x1d/0x50
[<ffffffffae3ee84e>] async_run_entry_fn+0xfe/0x610
[<ffffffffae3d0666>] process_one_work+0x716/0x1a50
[<ffffffffae3d05c9>] ? process_one_work+0x679/0x1a50
[<ffffffffafdd7b6d>] ? _raw_spin_unlock_irq+0x3d/0x60
[<ffffffffae3cff50>] ? pwq_dec_nr_in_flight+0x2b0/0x2b0
[<ffffffffae3d1a80>] worker_thread+0xe0/0x1460
[<ffffffffae3d19a0>] ? process_one_work+0x1a50/0x1a50
[<ffffffffae3e54c2>] kthread+0x222/0x2e0
[<ffffffffae3e52a0>] ? kthread_park+0x80/0x80
[<ffffffffae3e52a0>] ? kthread_park+0x80/0x80
[<ffffffffae3e52a0>] ? kthread_park+0x80/0x80
[<ffffffffafdd86aa>] ret_from_fork+0x2a/0x40
Object at ffff8803fc244088, in cache kmalloc-1024 size: 1024
Allocated:
PID = 71
save_stack_trace+0x1b/0x20
save_stack+0x46/0xd0
kasan_kmalloc+0xad/0xe0
kasan_slab_alloc+0x12/0x20
__kmalloc_track_caller+0x134/0x360
kmemdup+0x20/0x50
brcmf_cfg80211_attach+0x10b/0x3a90 [brcmfmac]
brcmf_bus_start+0x19a/0x9a0 [brcmfmac]
brcmf_pcie_setup+0x1f1a/0x3680 [brcmfmac]
brcmf_fw_request_nvram_done+0x44c/0x11b0 [brcmfmac]
request_firmware_work_func+0x135/0x280
process_one_work+0x716/0x1a50
worker_thread+0xe0/0x1460
kthread+0x222/0x2e0
ret_from_fork+0x2a/0x40
Freed:
PID = 2568
save_stack_trace+0x1b/0x20
save_stack+0x46/0xd0
kasan_slab_free+0x71/0xb0
kfree+0xe8/0x2e0
brcmf_cfg80211_detach+0x62/0xf0 [brcmfmac]
brcmf_detach+0x14a/0x2b0 [brcmfmac]
brcmf_pcie_remove+0x140/0x5d0 [brcmfmac]
brcmf_pcie_pm_leave_D3+0x198/0x2e0 [brcmfmac]
pci_pm_resume+0x186/0x220
dpm_run_callback+0x6e/0x4f0
device_resume+0x1c2/0x670
async_resume+0x1d/0x50
async_run_entry_fn+0xfe/0x610
process_one_work+0x716/0x1a50
worker_thread+0xe0/0x1460
kthread+0x222/0x2e0
ret_from_fork+0x2a/0x40
Memory state around the buggy address:
ffff8803fc243f80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff8803fc244000: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff8803fc244080: fc fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff8803fc244100: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff8803fc244180: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
What is happening is that brcmf_pcie_resume() detects a device that
is no longer responsive and it decides to unbind resulting in a
wiphy_unregister() and wiphy_free() call. Now the wiphy instance
remains allocated, because PM needs to call wiphy_resume() for it.
However, brcmfmac already does a kfree() for the struct
cfg80211_registered_device::ops field. Change the checks in
wiphy_resume() to only access the struct cfg80211_registered_device::ops
if the wiphy instance is still registered at this time.
Reported-by: Daniel J Blueman <daniel@quora.org>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09a6adf53d upstream.
After 52d7523 (arm64: mm: allow the kernel to handle alignment faults on
user accesses) commit user-land accesses that produce unaligned exceptions
like in case of aarch32 ldm/stm/ldrd/strd instructions operating on
unaligned memory received by user-land as SIGSEGV. It is wrong, it should
be reported as SIGBUS as it was before 52d7523 commit.
Changed do_bad_area function to take signal and code parameters out of esr
value using fault_info table, so in case of do_alignment_fault fault
user-land will receive SIGBUS. Wrapped access to fault_info table into
esr_to_fault_info function.
Fixes: 52d7523 (arm64: mm: allow the kernel to handle alignment faults on user accesses)
Signed-off-by: Victor Kamensky <kamensky@cisco.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4bdc902968 upstream.
The gyroscope chip might need to be reset to be used.
Without the chip being reset, the driver stopped at the first
regmap_read (to get the CHIP_ID) and failed to probe.
The datasheet of the gyroscope says that a minimum wait of 30ms after
the reset has to be done.
This patch has been checked on a BMX055 and the datasheet of the BMG160
and the BMI055 give the same reset register and bits.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 51f528a163 upstream.
This patch initializes the bootime in struct st_sensor_settings for
lps22hb sensor. Without this, sensor channels read from sysfs always
report stale values.
Signed-off-by: Shrirang Bagul <shrirang.bagul@canonical.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7fd6592d12 upstream.
Fix formatting of negative values of type IIO_VAL_FRACTIONAL_LOG2 by
switching from do_div(), which can't handle negative numbers, to
div_s64_rem(). Also use shift_right for shifting, which is safe with
negative values.
Signed-off-by: Nikolaus Schulz <nikolaus.schulz@avionic-design.de>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b3405e345 upstream.
In kvm_free_stage2_pgd() we don't hold the kvm->mmu_lock while calling
unmap_stage2_range() on the entire memory range for the guest. This could
cause problems with other callers (e.g, munmap on a memslot) trying to
unmap a range. And since we have to unmap the entire Guest memory range
holding a spinlock, make sure we yield the lock if necessary, after we
unmap each PUD range.
Fixes: commit d5d8184d35 ("KVM: ARM: Memory virtualization setup")
Cc: Paolo Bonzini <pbonzin@redhat.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
[ Avoid vCPU starvation and lockup detector warnings ]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 72f310481a upstream.
We don't hold the mmap_sem while searching for VMAs (via find_vma), in
kvm_arch_prepare_memory_region, which can end up in expected failures.
Fixes: commit 8eef91239e ("arm/arm64: KVM: map MMIO regions at creation time")
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Eric Auger <eric.auger@rehat.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
[ Handle dirty page logging failure case ]
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 90f6e150e4 upstream.
We don't hold the mmap_sem while searching for the VMAs when
we try to unmap each memslot for a VM. Fix this properly to
avoid unexpected results.
Fixes: commit 957db105c9 ("arm/arm64: KVM: Introduce stage2_unmap_vm")
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 97fbfef6bd upstream.
vfs_llseek will check whether the file mode has
FMODE_LSEEK, no return failure. But ashmem can be
lseek, so add FMODE_LSEEK to ashmem file.
Comment From Greg Hackmann:
ashmem_llseek() passes the llseek() call through to the backing
shmem file. 91360b02ab ("ashmem: use vfs_llseek()") changed
this from directly calling the file's llseek() op into a VFS
layer call. This also adds a check for the FMODE_LSEEK bit, so
without that bit ashmem_llseek() now always fails with -ESPIPE.
Fixes: 91360b02ab ("ashmem: use vfs_llseek()")
Signed-off-by: Shuxiao Zhang <zhangshuxiao@xiaomi.com>
Tested-by: Greg Hackmann <ghackmann@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c8a139d001 upstream.
ops->show() can return a negative error code.
Commit 65da3484d9 ("sysfs: correctly handle short reads on PREALLOC attrs.")
(in v4.4) caused this to be stored in an unsigned 'size_t' variable, so errors
would look like large numbers.
As a result, if an error is returned, sysfs_kf_read() will return the
value of 'count', typically 4096.
Commit 17d0774f80 ("sysfs: correctly handle read offset on PREALLOC attrs")
(in v4.8) extended this error to use the unsigned large 'len' as a size for
memmove().
Consequently, if ->show returns an error, then the first read() on the
sysfs file will return 4096 and could return uninitialized memory to
user-space.
If the application performs a subsequent read, this will trigger a memmove()
with extremely large count, and is likely to crash the machine is bizarre ways.
This bug can currently only be triggered by reading from an md
sysfs attribute declared with __ATTR_PREALLOC() during the
brief period between when mddev_put() deletes an mddev from
the ->all_mddevs list, and when mddev_delayed_delete() - which is
scheduled on a workqueue - completes.
Before this, an error won't be returned by the ->show()
After this, the ->show() won't be called.
I can reproduce it reliably only by putting delay like
usleep_range(500000,700000);
early in mddev_delayed_delete(). Then after creating an
md device md0 run
echo clear > /sys/block/md0/md/array_state; cat /sys/block/md0/md/array_state
The bug can be triggered without the usleep.
Fixes: 65da3484d9 ("sysfs: correctly handle short reads on PREALLOC attrs.")
Fixes: 17d0774f80 ("sysfs: correctly handle read offset on PREALLOC attrs")
Signed-off-by: NeilBrown <neilb@suse.com>
Acked-by: Tejun Heo <tj@kernel.org>
Reported-and-tested-by: Miroslav Benes <mbenes@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit feb199ebef upstream.
SZ_16M PEM resource size includes PEM-specific register and its children
resources. Reservation of the whole SZ_16M range leads to child device
driver failure when pcieport driver is requesting resources:
pcieport 0004:1f:00.0: can't enable device: BAR 0 [mem 0x87e0c0f00000-0x87e0c0ffffff 64bit] not claimed
So we cannot reserve full 16M here and instead we want to reserve
PEM-specific register only which is SZ_64K.
At the end increase PEM resource to SZ_16M since this is what
thunder_pem_init() call expects for proper initialization.
Fixes: 9abb27c759 ("PCI: thunder-pem: Add legacy firmware support for Cavium ThunderX host controller")
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9abb27c759 upstream.
During early days of PCI quirks support, ThunderX firmware did not provide
PNP0c02 node with PCI configuration space and PEM-specific register ranges.
This means that for legacy FW we are not reserving these resources and
cannot gather PEM-specific resources for further PEM initialization.
To support already deployed legacy FW, calculate PEM-specific ranges and
provide resources reservation as fallback scenario into PEM driver when we
could not gather PEM reg base from ACPI tables.
Tested-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Vadim Lomovtsev <Vadim.Lomovtsev@caviumnetworks.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7e11f9956 upstream.
In vmw_surface_define_ioctl(), the 'num_sizes' is the sum of the
'req->mip_levels' array. This array can be assigned any value from
the user space. As both the 'num_sizes' and the array is uint32_t,
it is easy to make 'num_sizes' overflow. The later 'mip_levels' is
used as the loop count. This can lead an oob write. Add the check of
'req->mip_levels' to avoid this.
Signed-off-by: Li Qiang <liqiang6-s@360.cn>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 53e16798b0 upstream.
The mesa winsys sometimes uses unimplemented parameter requests to
check for features. Remove the error message to avoid bloating the
kernel log.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe25deb773 upstream.
Previously, when a surface was opened using a legacy (non prime) handle,
it was verified to have been created by a client in the same master realm.
Relax this so that opening is also allowed recursively if the client
already has the surface open.
This works around a regression in svga mesa where opening of a shared
surface is used recursively to obtain surface information.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 63774069d9 upstream.
In vmw_get_cap_3d_ioctl(), a user can supply 0 for a size that is
used in vzalloc(). This eventually calls dump_stack() (in warn_alloc()),
which can leak useful addresses to dmesg.
Add check to avoid a size of 0.
Signed-off-by: Murray McAllister <murray.mcallister@insomniasec.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 36274ab8c5 upstream.
Before memory allocations vmw_surface_define_ioctl() checks the
upper-bounds of a user-supplied size, but does not check if the
supplied size is 0.
Add check to avoid NULL pointer dereferences.
Signed-off-by: Murray McAllister <murray.mcallister@insomniasec.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f7652afa8e upstream.
A malicious caller could otherwise hand over handles to other objects
causing all sorts of interesting problems.
Testing done: Ran a Fedora 25 desktop using both Xorg and
gnome-shell/Wayland.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6db28eda26 upstream.
If the device is not present, the driver should disable the queues
immediately. Prior to this, the driver was relying on the watchdog timer
to kill the queues if requests were outstanding to the device, and that
just delays removal up to one second.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f33447b90e upstream.
If a namespace has already been marked dead, we don't want to kick the
request_queue again since we may have just freed it from another thread.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit de5540d088 upstream.
Under extremely heavy uses of padata, crashes occur, and with list
debugging turned on, this happens instead:
[87487.298728] WARNING: CPU: 1 PID: 882 at lib/list_debug.c:33
__list_add+0xae/0x130
[87487.301868] list_add corruption. prev->next should be next
(ffffb17abfc043d0), but was ffff8dba70872c80. (prev=ffff8dba70872b00).
[87487.339011] [<ffffffff9a53d075>] dump_stack+0x68/0xa3
[87487.342198] [<ffffffff99e119a1>] ? console_unlock+0x281/0x6d0
[87487.345364] [<ffffffff99d6b91f>] __warn+0xff/0x140
[87487.348513] [<ffffffff99d6b9aa>] warn_slowpath_fmt+0x4a/0x50
[87487.351659] [<ffffffff9a58b5de>] __list_add+0xae/0x130
[87487.354772] [<ffffffff9add5094>] ? _raw_spin_lock+0x64/0x70
[87487.357915] [<ffffffff99eefd66>] padata_reorder+0x1e6/0x420
[87487.361084] [<ffffffff99ef0055>] padata_do_serial+0xa5/0x120
padata_reorder calls list_add_tail with the list to which its adding
locked, which seems correct:
spin_lock(&squeue->serial.lock);
list_add_tail(&padata->list, &squeue->serial.list);
spin_unlock(&squeue->serial.lock);
This therefore leaves only place where such inconsistency could occur:
if padata->list is added at the same time on two different threads.
This pdata pointer comes from the function call to
padata_get_next(pd), which has in it the following block:
next_queue = per_cpu_ptr(pd->pqueue, cpu);
padata = NULL;
reorder = &next_queue->reorder;
if (!list_empty(&reorder->list)) {
padata = list_entry(reorder->list.next,
struct padata_priv, list);
spin_lock(&reorder->lock);
list_del_init(&padata->list);
atomic_dec(&pd->reorder_objects);
spin_unlock(&reorder->lock);
pd->processed++;
goto out;
}
out:
return padata;
I strongly suspect that the problem here is that two threads can race
on reorder list. Even though the deletion is locked, call to
list_entry is not locked, which means it's feasible that two threads
pick up the same padata object and subsequently call list_add_tail on
them at the same time. The fix is thus be hoist that lock outside of
that block.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f5fe1b5190 upstream.
Commit 79bd99596b ("blk: improve order of bio handling in generic_make_request()")
changed current->bio_list so that it did not contain *all* of the
queued bios, but only those submitted by the currently running
make_request_fn.
There are two places which walk the list and requeue selected bios,
and others that check if the list is empty. These are no longer
correct.
So redefine current->bio_list to point to an array of two lists, which
contain all queued bios, and adjust various code to test or walk both
lists.
Signed-off-by: NeilBrown <neilb@suse.com>
Fixes: 79bd99596b ("blk: improve order of bio handling in generic_make_request()")
Signed-off-by: Jens Axboe <axboe@fb.com>
Cc: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 79bd99596b upstream.
To avoid recursion on the kernel stack when stacked block devices
are in use, generic_make_request() will, when called recursively,
queue new requests for later handling. They will be handled when the
make_request_fn for the current bio completes.
If any bios are submitted by a make_request_fn, these will ultimately
be handled seqeuntially. If the handling of one of those generates
further requests, they will be added to the end of the queue.
This strict first-in-first-out behaviour can lead to deadlocks in
various ways, normally because a request might need to wait for a
previous request to the same device to complete. This can happen when
they share a mempool, and can happen due to interdependencies
particular to the device. Both md and dm have examples where this happens.
These deadlocks can be erradicated by more selective ordering of bios.
Specifically by handling them in depth-first order. That is: when the
handling of one bio generates one or more further bios, they are
handled immediately after the parent, before any siblings of the
parent. That way, when generic_make_request() calls make_request_fn
for some particular device, we can be certain that all previously
submited requests for that device have been completely handled and are
not waiting for anything in the queue of requests maintained in
generic_make_request().
An easy way to achieve this would be to use a last-in-first-out stack
instead of a queue. However this will change the order of consecutive
bios submitted by a make_request_fn, which could have unexpected consequences.
Instead we take a slightly more complex approach.
A fresh queue is created for each call to a make_request_fn. After it completes,
any bios for a different device are placed on the front of the main queue, followed
by any bios for the same device, followed by all bios that were already on
the queue before the make_request_fn was called.
This provides the depth-first approach without reordering bios on the same level.
This, by itself, it not enough to remove all deadlocks. It just makes
it possible for drivers to take the extra step required themselves.
To avoid deadlocks, drivers must never risk waiting for a request
after submitting one to generic_make_request. This includes never
allocing from a mempool twice in the one call to a make_request_fn.
A common pattern in drivers is to call bio_split() in a loop, handling
the first part and then looping around to possibly split the next part.
Instead, a driver that finds it needs to split a bio should queue
(with generic_make_request) the second part, handle the first part,
and then return. The new code in generic_make_request will ensure the
requests to underlying bios are processed first, then the second bio
that was split off. If it splits again, the same process happens. In
each case one bio will be completely handled before the next one is attempted.
With this is place, it should be possible to disable the
punt_bios_to_recover() recovery thread for many block devices, and
eventually it may be possible to remove it completely.
Ref: http://www.spinics.net/lists/raid/msg54680.html
Tested-by: Jinpu Wang <jinpu.wang@profitbricks.com>
Inspired-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Cc: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c356eda22 upstream.
With the IRQ stack changes integrated, the XRX200 devices started
emitting a constant stream of kernel messages like this:
[ 565.415310] Spurious IRQ: CAUSE=0x1100c300
This is caused by IP0 getting handled by plat_irq_dispatch() rather than
its vectored interrupt handler, which is fixed by commit de856416e714
("MIPS: IRQ Stack: Fix erroneous jal to plat_irq_dispatch").
Fix plat_irq_dispatch() to handle non-vectored IPI interrupts correctly
by setting up IP2-6 as proper chained IRQ handlers and calling do_IRQ
for all MIPS CPU interrupts.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: John Crispin <john@phrozen.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15077/
[james.hogan@imgtec.com: tweaked commit message]
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c2bf9f959 upstream.
GIC_PPI flags were misconfigured for the timers, resulting in errors
like:
[ 0.000000] GIC: PPI11 is secure or misconfigured
Changing them to being edge triggered corrects the issue
Suggested-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Fixes: d27509f1 ("ARM: BCM5301X: add dts files for BCM4708 SoC")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0cefabdaf7 upstream.
Commit 0a6b76dd23 ("mm: workingset: make shadow node shrinker memcg
aware") enabled cgroup-awareness in the shadow node shrinker, but forgot
to also enable cgroup-awareness in the list_lru the shadow nodes sit on.
Consequently, all shadow nodes are sitting on a global (per-NUMA node)
list, while the shrinker applies the limits according to the amount of
cache in the cgroup its shrinking. The result is excessive pressure on
the shadow nodes from cgroups that have very little cache.
Enable memcg-mode on the shadow node LRUs, such that per-cgroup limits
are applied to per-cgroup lists.
Fixes: 0a6b76dd23 ("mm: workingset: make shadow node shrinker memcg aware")
Link: http://lkml.kernel.org/r/20170322005320.8165-1-hannes@cmpxchg.org
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Vladimir Davydov <vdavydov@tarantool.org>
Cc: Michal Hocko <mhocko@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 93a15b58cf upstream.
The kvmgt code keeps a pointer to the struct kvm associated with the
device, but doesn't actually hold a reference to it. If we do unclean
shutdown testing (ie. killing the user process), then we can see the
kvm association to the device unset, which causes kvmgt to trigger a
device release via a work queue. Naturally we cannot guarantee that
the cached struct kvm pointer is still valid at this point without
holding a reference. The observed failure in this case is a stuck
cpu trying to acquire the spinlock from the invalid reference, but
other failure modes are clearly possible. Hold a reference to avoid
this.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Cc: Jike Song <jike.song@intel.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Zhi Wang <zhi.a.wang@intel.com>
Reviewed-by: Jike Song <jike.song@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f3cd1b064f upstream.
The fence allocation needs to be protected by the GPU mutex, otherwise
the fence seqnos of concurrent submits might not match the insertion order
of the jobs in the kernel ring. This breaks the assumption that jobs
complete with monotonically increasing fence seqnos.
Fixes: d985349017 (drm/etnaviv: take GPU lock later in the submit process)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce4b4f228e upstream.
We were accidentally only overriding the first VRAM placement. For BOs
with the RADEON_GEM_NO_CPU_ACCESS flag set,
radeon_ttm_placement_from_domain creates a second VRAM placment with
fpfn == 0. If VRAM is almost full, the first VRAM placement with
fpfn > 0 may not work, but the second one with fpfn == 0 always will
(the BO's current location trivially satisfies it). Because "moving"
the BO to its current location puts it back on the LRU list, this
results in an infinite loop.
Fixes: 2a85aedd11 ("drm/radeon: Try evicting from CPU accessible to
inaccessible VRAM first")
Reported-by: Zachary Michaels <zmichaels@oblong.com>
Reported-and-Tested-by: Julien Isorce <jisorce@oblong.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 90db10434b upstream.
No caller currently checks the return value of
kvm_io_bus_unregister_dev(). This is evil, as all callers silently go on
freeing their device. A stale reference will remain in the io_bus,
getting at least used again, when the iobus gets teared down on
kvm_destroy_vm() - leading to use after free errors.
There is nothing the callers could do, except retrying over and over
again.
So let's simply remove the bus altogether, print an error and make
sure no one can access this broken bus again (returning -ENOMEM on any
attempt to access it).
Fixes: e93f8a0f82 ("KVM: convert io_bus to SRCU")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df630b8c1e upstream.
When releasing the bus, let's clear the bus pointers to mark it out. If
any further device unregister happens on this bus, we know that we're
done if we found the bus being released already.
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a6040bc610 upstream.
The reference manual for the i.MX28 recommends to calculate the divisor
as
divisor = (UARTCLK * 32) / baud rate, rounded to the nearest integer
, so let's do this. For a typical setup of UARTCLK = 24 MHz and baud
rate = 115200 this changes the divisor from 6666 to 6667 and so the
actual baud rate improves from 115211.521 Bd (error ≅ 0.01 %) to
115194.240 Bd (error ≅ 0.005 %).
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1633682053 upstream.
Using KASAN, Dmitry found a bug in the rh_call_control() routine: If
buffer allocation fails, the routine returns immediately without
unlinking its URB from the control endpoint, eventually leading to
linked-list corruption.
This patch fixes the problem by jumping to the end of the routine
(where the URB is unlinked) when an allocation failure occurs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0ab2881a40 upstream.
A control transfer that stopped at the status stage incorrectly
warned about a "unexpected TRB Type 4", and did not set the
transferred actual_length for the URB.
The URB actual_length for control transfers should contain the
bytes transferred in the data stage.
Bytes of a partially sent setup stage and missing bytes from
status stage should be left out.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 497e1e16f4 upstream.
A side effect of 89d8232411 ("tty/serial: atmel_serial: BUG: stop DMA
from transmitting in stop_tx") is that the console can be called with
TX path disabled. Then the system would hang trying to push charecters
out in atmel_console_putchar().
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Fixes: 89d8232411 ("tty/serial: atmel_serial: BUG: stop DMA from transmitting in stop_tx")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 31ca2c63fd upstream.
If uart_flush_buffer() is called between atmel_tx_dma() and
atmel_complete_tx_dma(), the circular buffer has been cleared, but not
atmel_port->tx_len.
That leads to a circular buffer overflow (dumping (UART_XMIT_SIZE -
atmel_port->tx_len) bytes).
Tested-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 08f63d9774 upstream.
No platform-device is required for IO(x)APICs, so don't even
create them.
[ rjw: This fixes a problem with leaking platform device objects
after IOAPIC/IOxAPIC hot-removal events.]
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61b79e16c6 upstream.
Paul Menzel reported a warning:
WARNING: CPU: 0 PID: 774 at /build/linux-ROBWaj/linux-4.9.13/kernel/trace/trace_functions_graph.c:233 ftrace_return_to_handler+0x1aa/0x1e0
Bad frame pointer: expected f6919d98, received f6919db0
from func acpi_pm_device_sleep_wake return to c43b6f9d
The warning means that function graph tracing is broken for the
acpi_pm_device_sleep_wake() function. That's because the ACPI Makefile
unconditionally sets the '-Os' gcc flag to optimize for size. That's an
issue because mcount-based function graph tracing is incompatible with
'-Os' on x86, thanks to the following gcc bug:
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=42109
I have another patch pending which will ensure that mcount-based
function graph tracing is never used with CONFIG_CC_OPTIMIZE_FOR_SIZE on
x86.
But this patch is needed in addition to that one because the ACPI
Makefile overrides that config option for no apparent reason. It has
had this flag since the beginning of git history, and there's no related
comment, so I don't know why it's there. As far as I can tell, there's
no reason for it to be there. The appropriate behavior is for it to
honor CONFIG_CC_OPTIMIZE_FOR_{SIZE,PERFORMANCE} like the rest of the
kernel.
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 554bfeceb8 upstream.
pa_memcpy() is the major memcpy implementation in the parisc kernel which is
used to do any kind of userspace/kernel memory copies.
Al Viro noticed various bugs in the implementation of pa_mempcy(), most notably
that in case of faults it may report back to have copied more bytes than it
actually did.
Fixing those bugs is quite hard in the C-implementation, because the compiler
is messing around with the registers and we are not guaranteed that specific
variables are always in the same processor registers. This makes proper fault
handling complicated.
This patch implements pa_memcpy() in assembler. That way we have correct fault
handling and adding a 64-bit copy routine was quite easy.
Runtime tested with 32- and 64bit kernels.
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 476e75a44b upstream.
Commit 73580dac76 ("parisc: Fix system shutdown halt") introduced an endless
loop for systems which don't provide a software power off function. But the
soft lockup detector will detect this and report stalled CPUs after some time.
Avoid those unwanted warnings by disabling the soft lockup detector.
Fixes: 73580dac76 ("parisc: Fix system shutdown halt")
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d19f5e41b3 upstream.
Al Viro noticed that userspace accesses via get_user()/put_user() can be
simplified a lot with regard to usage of the exception handling.
This patch implements a fixup routine for get_user() and put_user() in such
that the exception handler will automatically load -EFAULT into the register
%r8 (the error value) in case on a fault on userspace. Additionally the fixup
routine will zero the target register on fault in case of a get_user() call.
The target register is extracted out of the faulting assembly instruction.
This patch brings a few benefits over the old implementation:
1. Exception handling gets much cleaner, easier and smaller in size.
2. Helper functions like fixup_get_user_skip_1 (all of fixup.S) can be dropped.
3. No need to hardcode %r9 as target register for get_user() any longer. This
helps the compiler register allocator and thus creates less assembler
statements.
4. No dependency on the exception_data contents any longer.
5. Nested faults will be handled cleanly.
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 74d1cf4897 upstream.
Commit 52060836f7 ("dt-bindings: omap-rng: Document SafeXcel IP-76
device variant") update the omap_rng Device Tree binding to add support
for the IP-76 variation of the IP. As part of this change, a "clocks"
property was added, but is indicated as "Required", without indicated
it's actually only required for some compatible strings.
This commit fixes that, by explicitly stating that the clocks property
is only required with the inside-secure,safexcel-eip76 compatible
string.
Fixes: 52060836f7 ("dt-bindings: omap-rng: Document SafeXcel IP-76 device variant")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0e3d3e5df0 upstream.
Commit 63d63cbf5e "NFSv4.1: Don't recheck delegations that
have already been checked" introduced a regression where when a
client received BAD_STATEID error it would not send any TEST_STATEID
and instead go into an infinite loop of resending the IO that caused
the BAD_STATEID.
Fixes: 63d63cbf5e ("NFSv4.1: Don't recheck delegations that have already been checked")
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c70c473396 upstream.
As reported in STAR 9001165532, an SLC control reg read (for checking
busy state) right after SLC invalidate command may incorrectly return
NOT busy causing software to NOT spin-wait while operation is underway.
(and for some reason this only happens if L1 cache is also disabled - as
required by IOC programming model)
Suggested workaround is to do an additional Control Reg read, which
ensures the 2nd read gets the right status.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
[vgupta: reworte changelog a bit]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9df0eb180c upstream.
In the generic XTS and LRW algorithms, for input data > 128 bytes, a
temporary buffer is allocated to hold the values to be XOR'ed with the
data before and after encryption or decryption. If the allocation
fails, the fixed-size buffer embedded in the request buffer is meant to
be used as a fallback --- resulting in more calls to the ECB algorithm,
but still producing the correct result. However, we weren't correctly
limiting subreq->cryptlen in this case, resulting in pre_crypt()
overrunning the embedded buffer. Fix this by setting subreq->cryptlen
correctly.
Fixes: f1c131b454 ("crypto: xts - Convert to skcipher")
Fixes: 700cb3f5fe ("crypto: lrw - Convert to skcipher")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit efc989fce8 upstream.
The CCP registers its queues as channels capable of handling
general DMA operations. The NTB driver will use DMA if
directed, but as public channels can be reserved for use in
asynchronous operations some channels should be held back
as private. Since the public/private determination is
handled at a device level, reserve the "other" (secondary)
CCP channels as private.
Add a module parameter that allows for override, to be
applied to all channels on all devices.
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0918764c1 upstream.
The controller has different timings for MMC_TIMING_UHS_DDR50 and
MMC_TIMING_MMC_DDR52. Configuring the controller with SDHCI_CTRL_UHS_DDR50,
when MMC_TIMING_MMC_DDR52 timings are requested, is not correct and can
lead to unexpected behavior.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Fixes: bb5f8ea4d5 ("mmc: sdhci-of-at91: introduce driver for the Atmel SDMMC")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 923713b357 upstream.
SDIO cards may need clock to send the card interrupt to the host.
On a cherrytrail tablet with a RTL8723BS wifi chip, without this patch
pinging the tablet results in:
PING 192.168.1.14 (192.168.1.14) 56(84) bytes of data.
64 bytes from 192.168.1.14: icmp_seq=1 ttl=64 time=78.6 ms
64 bytes from 192.168.1.14: icmp_seq=2 ttl=64 time=1760 ms
64 bytes from 192.168.1.14: icmp_seq=3 ttl=64 time=753 ms
64 bytes from 192.168.1.14: icmp_seq=4 ttl=64 time=3.88 ms
64 bytes from 192.168.1.14: icmp_seq=5 ttl=64 time=795 ms
64 bytes from 192.168.1.14: icmp_seq=6 ttl=64 time=1841 ms
64 bytes from 192.168.1.14: icmp_seq=7 ttl=64 time=810 ms
64 bytes from 192.168.1.14: icmp_seq=8 ttl=64 time=1860 ms
64 bytes from 192.168.1.14: icmp_seq=9 ttl=64 time=812 ms
64 bytes from 192.168.1.14: icmp_seq=10 ttl=64 time=48.6 ms
Where as with this patch I get:
PING 192.168.1.14 (192.168.1.14) 56(84) bytes of data.
64 bytes from 192.168.1.14: icmp_seq=1 ttl=64 time=3.96 ms
64 bytes from 192.168.1.14: icmp_seq=2 ttl=64 time=1.97 ms
64 bytes from 192.168.1.14: icmp_seq=3 ttl=64 time=17.2 ms
64 bytes from 192.168.1.14: icmp_seq=4 ttl=64 time=2.46 ms
64 bytes from 192.168.1.14: icmp_seq=5 ttl=64 time=2.83 ms
64 bytes from 192.168.1.14: icmp_seq=6 ttl=64 time=1.40 ms
64 bytes from 192.168.1.14: icmp_seq=7 ttl=64 time=2.10 ms
64 bytes from 192.168.1.14: icmp_seq=8 ttl=64 time=1.40 ms
64 bytes from 192.168.1.14: icmp_seq=9 ttl=64 time=2.04 ms
64 bytes from 192.168.1.14: icmp_seq=10 ttl=64 time=1.40 ms
Cc: Dong Aisheng <b29396@freescale.com>
Cc: Ian W MORRISON <ianwmorrison@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b40735969 upstream.
A previous commit (below) adds a check for already probed interfaces to
Wacom's matching heuristic. Unfortunately this causes the Bamboo Pen
(CTL-460) to match itself to its 'ghost' touch interface. After
subsequent changes to the driver this match to the ghost causes the
kernel to crash. This patch avoids calling wacom_add_shared_data()
for the BAMBOO_PEN's ghost touch interface.
Fixes: 41372d5d40 ("HID: wacom: Augment 'oVid' and 'oPid' with heuristics for HID_GENERIC")
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d1a6fe41d3 upstream.
In 'skl_tplg_set_module_init_data()', a pointer to 'params' member of
'struct skl_algo_data' is calculated, then casted to (u32 *) and assigned
to a member of configuration data. The configuration data is passed to the
other functions and used to process intel IPC. In this processing, the
value of member is used to get message data, however this can bring invalid
memory access in 'skl_set_module_params()' as a result of calculation of
a pointer for actual message data.
(sound/soc/intel/skylake/skl-topology.c)
skl_tplg_init_pipe_modules()
->skl_tplg_set_module_init_data() (has this bug)
->skl_tplg_set_module_params()
(sound/soc/intel/skylake/skl-messages.c)
->skl_set_module_params()
((char *)param) + data_offset
This commit fixes the bug.
Fixes: abb740033b ("ASoC: Intel: Skylake: Add support to configure module params")
Signed-off-by: Takashi Sakamoto <takashi.sakamoto@miraclelinux.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f726aec19 upstream.
On this Dell AIO machine, the lineout jack does not work.
We found the pin 0x1a is assigned to lineout on this machine, and in
the past, we applied ALC298_FIXUP_DELL1_MIC_NO_PRESENCE to fix the
heaset-set mic problem for this machine, this fixup will redefine
the pin 0x1a to headphone-mic, as a result the lineout doesn't
work anymore.
After consulting with Dell, they told us this machine doesn't support
microphone via headset jack, so we add a new fixup which only defines
the pin 0x18 as the headset-mic.
[rearranged the fixup insertion position by tiwai in order to make the
merge with other branches easier -- tiwai]
Fixes: 59ec4b57bc ("ALSA: hda - Fix headset mic detection problem for two dell machines")
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2d7d54002e upstream.
When a new event is queued while processing to resize the FIFO in
snd_seq_fifo_clear(), it may lead to a use-after-free, as the old pool
that is being queued gets removed. For avoiding this race, we need to
close the pool to be deleted and sync its usage before actually
deleting it.
The issue was spotted by syzkaller.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81caa91b72 upstream.
"CAV" is the only PNP/ACPI hardware ID vendor prefix assigned to Cavium so
fix this as it should be from day one.
Fixes: 44f22bd91e ("PCI: Add MCFG quirks for Cavium ThunderX pass2.x host controller")
Tested-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e347b5e05 upstream.
The host bridge memory window resource is inserted into the iomem_resource
tree and cannot be deallocated until the host bridge itself is removed.
Previously, the window was on the stack, which meant the iomem_resource
entry pointed into the stack and was corrupted as soon as the probe
function returned, which caused memory corruption and errors like this:
pcie_iproc_bcma bcma0:8: resource collision: [mem 0x40000000-0x47ffffff] conflicts with PCIe MEM space [mem 0x40000000-0x47ffffff]
Move the memory window resource from the stack into struct iproc_pcie so
its lifetime matches that of the host bridge.
Fixes: c3245a5664 ("PCI: iproc: Request host bridge window resources")
Reported-and-tested-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7cb689fe42 upstream.
Callers of scsi_dh_activate(), e.g. dm-mpath, assume that this function
either returns an error code or calls the completion function. Make
alua_activate() call the completion function even if scsi_device_get()
fails.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Tang Junhui <tang.junhui@zte.com.cn>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9702c67c60 upstream.
The total ata xfer length may not be calculated properly, in that we do
not use the proper method to get an sg element dma length.
According to the code comment, sg_dma_len() should be used after
dma_map_sg() is called.
This issue was found by turning on the SMMUv3 in front of the hisi_sas
controller in hip07. Multiple sg elements were being combined into a
single element, but the original first element length was being use as
the total xfer length.
Fixes: ff2aeb1eb6 ("libata: convert to chained sg")
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf33f87dd0 upstream.
The user can control the size of the next command passed along, but the
value passed to the ioctl isn't checked against the usable max command
size.
Signed-off-by: Peter Chang <dpf@google.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2fcc319d24 upstream.
When a reflink operation causes the bmap code to allocate a btree block
we're currently doing single-AG allocations due to having ->firstblock
set and then try any higher AG due a little reflink quirk we've put in
when adding the reflink code. But given that we do not have a minleft
reservation of any kind in this AG we can still not have any space in
the same or higher AG even if the file system has enough free space.
To fix this use a XFS_ALLOCTYPE_FIRST_AG allocation in this fall back
path instead.
[And yes, we need to redo this properly instead of piling hacks over
hacks. I'm working on that, but it's not going to be a small series.
In the meantime this fixes the customer reported issue]
Also add a warning for failing allocations to make it easier to debug.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f65e6fad29 upstream.
Commit fa7f138 ("xfs: clear delalloc and cache on buffered write
failure") fixed one regression in the iomap error handling code and
exposed another. The fundamental problem is that if a buffered write
is a rewrite of preexisting delalloc blocks and the write fails, the
failure handling code can punch out preexisting blocks with valid
file data.
This was reproduced directly by sub-block writes in the LTP
kernel/syscalls/write/write03 test. A first 100 byte write allocates
a single block in a file. A subsequent 100 byte write fails and
punches out the block, including the data successfully written by
the previous write.
To address this problem, update the ->iomap_begin() handler to
distinguish newly allocated delalloc blocks from preexisting
delalloc blocks via the IOMAP_F_NEW flag. Use this flag in the
->iomap_end() handler to decide when a failed or short write should
punch out delalloc blocks.
This introduces the subtle requirement that ->iomap_begin() should
never combine newly allocated delalloc blocks with existing blocks
in the resulting iomap descriptor. This can occur when a new
delalloc reservation merges with a neighboring extent that is part
of the current write, for example. Therefore, drop the
post-allocation extent lookup from xfs_bmapi_reserve_delalloc() and
just return the record inserted into the fork. This ensures only new
blocks are returned and thus that preexisting delalloc blocks are
always handled as "found" blocks and not punched out on a failed
rewrite.
Reported-by: Xiong Zhou <xzhou@redhat.com>
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d5825712ee upstream.
When block size is larger than inode cluster size, the call to
XFS_B_TO_FSBT(mp, mp->m_inode_cluster_size) returns 0. Also, mkfs.xfs
would have set xfs_sb->sb_inoalignmt to 0. Hence in
xfs_set_inoalignment(), xfs_mount->m_inoalign_mask gets initialized to
-1 instead of 0. However, xfs_mount->m_sinoalign would get correctly
intialized to 0 because for every positive value of xfs_mount->m_dalign,
the condition "!(mp->m_dalign & mp->m_inoalign_mask)" would evaluate to
false.
Also, xfs_imap() worked fine even with xfs_mount->m_inoalign_mask having
-1 as the value because blks_per_cluster variable would have the value 1
and hence we would never have a need to use xfs_mount->m_inoalign_mask
to compute the inode chunk's agbno and offset within the chunk.
Signed-off-by: Chandan Rajendra <chandan@linux.vnet.ibm.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 787eb48550 upstream.
There are two different cases of buffered I/O errors:
- first we can have an already shutdown fs. In that case we should skip
any on-disk operations and just clean up the appen transaction if
present and destroy the ioend
- a real I/O error. In that case we should cleanup any lingering COW
blocks. This gets skipped in the current code and is fixed by this
patch.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3802a34532 upstream.
We only want to reclaim preallocations from our periodic work item.
Currently this is archived by looking for a dirty inode, but that check
is rather fragile. Instead add a flag to xfs_reflink_cancel_cow_* so
that the caller can ask for just cancelling unwritten extents in the COW
fork.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
[darrick: fix typos in commit message]
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 410d17f67e upstream.
In various places we currently assert that xfs_bmap_btalloc allocates
from the same as the firstblock value passed in, unless it's either
NULLAGNO or the dop_low flag is set. But the reflink code does not
fully follow this convention as it passes in firstblock purely as
a hint for the allocator without actually having previous allocations
in the transaction, and without having a minleft check on the current
AG, leading to the assert firing on a very full and heavily used
file system. As even the reflink code only allocates from equal or
higher AGs for now we can simply the check to always allow for equal
or higher AGs.
Note that we need to eventually split the two meanings of the firstblock
value. At that point we can also allow the reflink code to allocate
from any AG instead of limiting it in any way.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 48af96ab92 upstream.
The block reservation for the transaction allocated in
xfs_shift_file_space() is an artifact of the original collapse range
support. It exists to handle the case where a collapse range occurs,
the initial extent is left shifted into a location that forms a
contiguous boundary with the previous extent and thus the extents
are merged. This code was subsequently refactored and reused for
insert range (right shift) support.
If an insert range occurs under low free space conditions, the
extent at the starting offset is split before the first shift
transaction is allocated. If the block reservation fails, this
leaves separate, but contiguous extents around in the inode. While
not a fatal problem, this is unexpected and will flag a warning on
subsequent insert range operations on the inode. This problem has
been reproduce intermittently by generic/270 running against a
ramdisk device.
Since right shift does not create new extent boundaries in the
inode, a block reservation for extent merge is unnecessary. Update
xfs_shift_file_space() to conditionally reserve fs blocks for left
shift transactions only. This avoids the warning reproduced by
generic/270.
Reported-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 75d65361cf upstream.
Certain workoads that punch holes into speculative preallocation can
cause delalloc indirect reservation splits when the delalloc extent is
split in two. If further splits occur, an already short-handed extent
can be split into two in a manner that leaves zero indirect blocks for
one of the two new extents. This occurs because the shortage is large
enough that the xfs_bmap_split_indlen() algorithm completely drains the
requested indlen of one of the extents before it honors the existing
reservation.
This ultimately results in a warning from xfs_bmap_del_extent(). This
has been observed during file copies of large, sparse files using 'cp
--sparse=always.'
To avoid this problem, update xfs_bmap_split_indlen() to explicitly
apply the reservation shortage fairly between both extents. This smooths
out the overall indlen shortage and defers the situation where we end up
with a delalloc extent with zero indlen reservation to extreme
circumstances.
Reported-by: Patrick Dung <mpatdung@gmail.com>
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0e339ef855 upstream.
When a delalloc extent is created, it can be merged with pre-existing,
contiguous, delalloc extents. When this occurs,
xfs_bmap_add_extent_hole_delay() merges the extents along with the
associated indirect block reservations. The expectation here is that the
combined worst case indlen reservation is always less than or equal to
the indlen reservation for the individual extents.
This is not always the case, however, as existing extents can less than
the expected indlen reservation if the extent was previously split due
to a hole punch. If a new extent merges with such an extent, the total
indlen requirement may be larger than the sum of the indlen reservations
held by both extents.
xfs_bmap_add_extent_hole_delay() assumes that the worst case indlen
reservation is always available and assigns it to the merged extent
without consideration for the indlen held by the pre-existing extent. As
a result, the subsequent xfs_mod_fdblocks() call can attempt an
unintentional allocation rather than a free (indicated by an ASSERT()
failure). Further, if the allocation happens to fail in this context,
the failure goes unhandled and creates a filesystem wide block
accounting inconsistency.
Fix xfs_bmap_add_extent_hole_delay() to function as designed. Cap the
indlen reservation assigned to the merged extent to the sum of the
indlen reservations held by each of the individual extents.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e30c23d13 upstream.
We don't just need the structure to track busy extents which can be
avoided with a synchronous transaction, but also to keep track of
pending discard.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b20fe4730e upstream.
If pag cannot be allocated, the current error exit path will trip
a null pointer deference error when calling xfs_buf_hash_destroy
with a null pag. Fix this by adding a new error exit labels and
jumping to those accordingly, avoiding the hash destroy and
unnecessary kmem_free on pag.
Up to three things need to be properly unwound:
1) pag memory allocation
2) xfs_buf_hash_init
3) radix_tree_insert
For any given iteration through the loop, any of the above which
succeed must be unwound for /this/ pag, and then all prior
initialized pags must be unwound.
Addresses-Coverity-Id: 1397628 ("Dereference after null check")
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Bill O'Donnell <billodo@redhat.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c5ecb42342 upstream.
We're changing both metadata and data, so we need to update the
timestamps for clone operations. Dedupe on the other hand does
not change file data, and only changes invisible metadata so the
timestamps should not be updated.
This follows existing btrfs behavior.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
[darrick: remove redundant is_dedupe test]
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54a4ef8af4 upstream.
We currently fall back from direct to buffered writes if we detect a
remaining shared extent in the iomap_begin callback. But by the time
iomap_begin is called for the potentially unaligned end block we might
have already written most of the data to disk, which we'd now write
again using buffered I/O. To avoid this reject all writes to reflinked
files before starting I/O so that we are guaranteed to only write the
data once.
The alternative would be to unshare the unaligned start and/or end block
before doing the I/O. I think that's doable, and will actually be
required to support reflinks on DAX file system. But it will take a
little more time and I'd rather get rid of the double write ASAP.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4dd2eb6335 upstream.
After successful IO or permanent error, b_first_retry_time also
needs to be cleared, else the invalid first retry time will be
used by the next retry check.
Signed-off-by: Hou Tao <houtao1@huawei.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5eda430000 upstream.
Christoph Hellwig pointed out that there's a potentially nasty race when
performing simultaneous nearby directio cow writes:
"Thread 1 writes a range from B to c
" B --------- C
p
"a little later thread 2 writes from A to B
" A --------- B
p
[editor's note: the 'p' denote cowextsize boundaries, which I added to
make this more clear]
"but the code preallocates beyond B into the range where thread
"1 has just written, but ->end_io hasn't been called yet.
"But once ->end_io is called thread 2 has already allocated
"up to the extent size hint into the write range of thread 1,
"so the end_io handler will splice the unintialized blocks from
"that preallocation back into the file right after B."
We can avoid this race by ensuring that thread 1 cannot accidentally
remap the blocks that thread 2 allocated (as part of speculative
preallocation) as part of t2's write preparation in t1's end_io handler.
The way we make this happen is by taking advantage of the unwritten
extent flag as an intermediate step.
Recall that when we begin the process of writing data to shared blocks,
we create a delayed allocation extent in the CoW fork:
D: --RRRRRRSSSRRRRRRRR---
C: ------DDDDDDD---------
When a thread prepares to CoW some dirty data out to disk, it will now
convert the delalloc reservation into an /unwritten/ allocated extent in
the cow fork. The da conversion code tries to opportunistically
allocate as much of a (speculatively prealloc'd) extent as possible, so
we may end up allocating a larger extent than we're actually writing
out:
D: --RRRRRRSSSRRRRRRRR---
U: ------UUUUUUU---------
Next, we convert only the part of the extent that we're actively
planning to write to normal (i.e. not unwritten) status:
D: --RRRRRRSSSRRRRRRRR---
U: ------UURRUUU---------
If the write succeeds, the end_cow function will now scan the relevant
range of the CoW fork for real extents and remap only the real extents
into the data fork:
D: --RRRRRRRRSRRRRRRRR---
U: ------UU--UUU---------
This ensures that we never obliterate valid data fork extents with
unwritten blocks from the CoW fork.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05a630d76b upstream.
In the data fork, we only allow extents to perform the following state
transitions:
delay -> real <-> unwritten
There's no way to move directly from a delalloc reservation to an
/unwritten/ allocated extent. However, for the CoW fork we want to be
able to do the following to each extent:
delalloc -> unwritten -> written -> remapped to data fork
This will help us to avoid a race in the speculative CoW preallocation
code between a first thread that is allocating a CoW extent and a second
thread that is remapping part of a file after a write. In order to do
this, however, we need two things: first, we have to be able to
transition from da to unwritten, and second the function that converts
between real and unwritten has to be made aware of the cow fork. Do
both of those things.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit de14c5f541 upstream.
Perform basic sanity checking of the directory free block header
fields so that we avoid hanging the system on invalid data.
(Granted that just means that now we shutdown on directory write,
but that seems better than hanging...)
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b3bf607d58 upstream.
We can't handle a bmbt that's taller than BTREE_MAXLEVELS, and there's
no such thing as a zero-level bmbt (for that we have extents format),
so if we see this, send back an error code.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d5a91baeb6 upstream.
Don't let anybody load an obviously bad btree pointer. Since the values
come from disk, we must return an error, not just ASSERT.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a652bbe36 upstream.
When we open a directory, we try to readahead block 0 of the directory
on the assumption that we're going to need it soon. If the bmbt is
corrupt, the directory will never be usable and the readahead fails
immediately, so we might as well prevent the directory from being opened
at all. This prevents a subsequent read or modify operation from
hitting it and taking the fs offline.
NOTE: We're only checking for early failures in the block mapping, not
the readahead directory block itself.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4b5bd5bf3f upstream.
We use di_format and if_flags to decide whether we're grabbing the ilock
in btree mode (btree extents not loaded) or shared mode (anything else),
but the state of those fields can be changed by other threads that are
also trying to load the btree extents -- IFEXTENTS gets set before the
_bmap_read_extents call and cleared if it fails.
We don't actually need to have IFEXTENTS set until after the bmbt
records are successfully loaded and validated, which will fix the race
between multiple threads trying to read the same directory. The next
patch strengthens directory bmbt validation by refusing to open the
directory if reading the bmbt to start directory readahead fails.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e4229d6b0b upstream.
It's possible for post-eof blocks to end up being used for direct I/O
writes. dio write performs an upfront unwritten extent allocation, sends
the dio and then updates the inode size (if necessary) on write
completion. If a file release occurs while a file extending dio write is
in flight, it is possible to mistake the post-eof blocks for speculative
preallocation and incorrectly truncate them from the inode. This means
that the resulting dio write completion can discover a hole and allocate
new blocks rather than perform unwritten extent conversion.
This requires a strange mix of I/O and is thus not likely to reproduce
in real world workloads. It is intermittently reproduced by generic/299.
The error manifests as an assert failure due to transaction overrun
because the aforementioned write completion transaction has only
reserved enough blocks for btree operations:
XFS: Assertion failed: tp->t_blk_res_used <= tp->t_blk_res, \
file: fs/xfs//xfs_trans.c, line: 309
The root cause is that xfs_free_eofblocks() uses i_size to truncate
post-eof blocks from the inode, but async, file extending direct writes
do not update i_size until write completion, long after inode locks are
dropped. Therefore, xfs_free_eofblocks() effectively truncates the inode
to the incorrect size.
Update xfs_free_eofblocks() to serialize against dio similar to how
extending writes are serialized against i_size updates before post-eof
block zeroing. Specifically, wait on dio while under the iolock. This
ensures that dio write completions have updated i_size before post-eof
blocks are processed.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c3155097ad upstream.
The xfs_eofblocks.eof_scan_owner field is an internal field to
facilitate invoking eofb scans from the kernel while under the iolock.
This is necessary because the eofb scan acquires the iolock of each
inode. Synchronous scans are invoked on certain buffered write failures
while under iolock. In such cases, the scan owner indicates that the
context for the scan already owns the particular iolock and prevents a
double lock deadlock.
eofblocks scans while under iolock are still livelock prone in the event
of multiple parallel scans, however. If multiple buffered writes to
different inodes fail and invoke eofblocks scans at the same time, each
scan avoids a deadlock with its own inode by virtue of the
eof_scan_owner field, but will never be able to acquire the iolock of
the inode from the parallel scan. Because the low free space scans are
invoked with SYNC_WAIT, the scan will not return until it has processed
every tagged inode and thus both scans will spin indefinitely on the
iolock being held across the opposite scan. This problem can be
reproduced reliably by generic/224 on systems with higher cpu counts
(x16).
To avoid this problem, simplify the semantics of eofblocks scans to
never invoke a scan while under iolock. This means that the buffered
write context must drop the iolock before the scan. It must reacquire
the lock before the write retry and also repeat the initial write
checks, as the original state might no longer be valid once the iolock
was dropped.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a36b926180 upstream.
xfs_free_eofblocks() requires the IOLOCK_EXCL lock, but is called from
different contexts where the lock may or may not be held. The
need_iolock parameter exists for this reason, to indicate whether
xfs_free_eofblocks() must acquire the iolock itself before it can
proceed.
This is ugly and confusing. Simplify the semantics of
xfs_free_eofblocks() to require the caller to acquire the iolock
appropriately and kill the need_iolock parameter. While here, the mp
param can be removed as well as the xfs_mount is accessible from the
xfs_inode structure. This patch does not change behavior.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ad658b693 upstream.
The nested_ept_enabled flag introduced in commit 7ca29de213 was not
computed correctly. We are interested only in L1's EPT state, not the
the combined L0+L1 value.
In particular, if L0 uses EPT but L1 does not, nested_ept_enabled must
be false to make sure that PDPSTRs are loaded based on CR3 as usual,
because the special case described in 26.3.2.4 Loading Page-Directory-
Pointer-Table Entries does not apply.
Fixes: 7ca29de213 ("KVM: nVMX: fix CR3 load if L2 uses PAE paging and EPT")
Cc: qemu-stable@nongnu.org
Reported-by: Wanpeng Li <wanpeng.li@hotmail.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 619bd4a718 upstream.
Since the change in commit:
fd7a4bed18 ("sched, rt: Convert switched_{from, to}_rt() / prio_changed_rt() to balance callbacks")
... we don't reschedule a task under certain circumstances:
Lets say task-A, SCHED_OTHER, is running on CPU0 (and it may run only on
CPU0) and holds a PI lock. This task is removed from the CPU because it
used up its time slice and another SCHED_OTHER task is running. Task-B on
CPU1 runs at RT priority and asks for the lock owned by task-A. This
results in a priority boost for task-A. Task-B goes to sleep until the
lock has been made available. Task-A is already runnable (but not active),
so it receives no wake up.
The reality now is that task-A gets on the CPU once the scheduler decides
to remove the current task despite the fact that a high priority task is
enqueued and waiting. This may take a long time.
The desired behaviour is that CPU0 immediately reschedules after the
priority boost which made task-A the task with the lowest priority.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: fd7a4bed18 ("sched, rt: Convert switched_{from, to}_rt() prio_changed_rt() to balance callbacks")
Link: http://lkml.kernel.org/r/20170124144006.29821-1-bigeasy@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7195ee3120 upstream.
It's not clear what behaviour is sensible when doing partial write of
NT_METAG_RPIPE, so just don't bother.
This patch assumes that userspace will never rely on a partial SETREGSET
in this case, since it's not clear what should happen anyway.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d614fd58a2 upstream.
Ensure that if userspace supplies insufficient data to PTRACE_SETREGSET
to fill all the registers, the thread's old registers are preserved.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 502585c755 upstream.
regs_set() and regs_get() are vulnerable to an off-by-1 buffer overrun
if CONFIG_CPU_H8S is set, since this adds an extra entry to
register_offset[] but not to user_regs_struct.
So, iterate over user_regs_struct based on its actual size, not based on
the length of register_offset[].
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb411b837b upstream.
gpr_set won't work correctly and can never have been tested, and the
correct behaviour is not clear due to the endianness-dependent task
layout.
So, just remove it. The core code will now return -EOPNOTSUPPORT when
trying to set NT_PRSTATUS on this architecture until/unless a correct
implementation is supplied.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc8653228c upstream.
When init_vqs runs, virtio_balloon.stats is either uninitialized or
contains stale values. The host updates its state with garbage data
because it has no way of knowing that this is just a marker buffer
used for signaling.
This patch updates the stats before pushing the initial buffer.
Alternative fixes:
* Push an empty buffer in init_vqs. Not easily done with the current
virtio implementation and violates the spec "Driver MUST supply the
same subset of statistics in all buffers submitted to the statsq".
* Push a buffer with invalid tags in init_vqs. Violates the same
spec clause, plus "invalid tag" is not really defined.
Note: the spec says:
When using the legacy interface, the device SHOULD ignore all values in
the first buffer in the statsq supplied by the driver after device
initialization. Note: Historically, drivers supplied an uninitialized
buffer in the first buffer.
Unfortunately QEMU does not seem to implement the recommendation
even for the legacy interface.
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 63cb6d5f00 upstream.
This can be reproduced by running kvm-unit-tests/vmx.flat on L0 w/ vpid disabled.
Test suite: VPID
Unhandled exception 6 #UD at ip 00000000004051a6
error_code=0000 rflags=00010047 cs=00000008
rax=0000000000000000 rcx=0000000000000001 rdx=0000000000000047 rbx=0000000000402f79
rbp=0000000000456240 rsi=0000000000000001 rdi=0000000000000000
r8=000000000000000a r9=00000000000003f8 r10=0000000080010011 r11=0000000000000000
r12=0000000000000003 r13=0000000000000708 r14=0000000000000000 r15=0000000000000000
cr0=0000000080010031 cr2=0000000000000000 cr3=0000000007fff000 cr4=0000000000002020
cr8=0000000000000000
STACK: @4051a6 40523e 400f7f 402059 40028f
We should hide and forbid VPID in L1 if it is disabled on L0. However, nested VPID
enable bit is set unconditionally during setup nested vmx exec controls though VPID
is not exposed through nested VMX capablity. This patch fixes it by don't set nested
VPID enable bit if it is disabled on L0.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Fixes: 5c614b3583 (KVM: nVMX: nested VPID emulation)
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f843ee6dd0 upstream.
Kees Cook has pointed out that xfrm_replay_state_esn_len() is subject to
wrapping issues. To ensure we are correctly ensuring that the two ESN
structures are the same size compare both the overall size as reported
by xfrm_replay_state_esn_len() and the internal length are the same.
CVE-2017-7184
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 677e806da4 upstream.
When a new xfrm state is created during an XFRM_MSG_NEWSA call we
validate the user supplied replay_esn to ensure that the size is valid
and to ensure that the replay_window size is within the allocated
buffer. However later it is possible to update this replay_esn via a
XFRM_MSG_NEWAE call. There we again validate the size of the supplied
buffer matches the existing state and if so inject the contents. We do
not at this point check that the replay_window is within the allocated
memory. This leads to out-of-bounds reads and writes triggered by
netlink packets. This leads to memory corruption and the potential for
priviledge escalation.
We already attempt to validate the incoming replay information in
xfrm_new_ae() via xfrm_replay_verify_len(). This confirms that the user
is not trying to change the size of the replay state buffer which
includes the replay_esn. It however does not check the replay_window
remains within that buffer. Add validation of the contained
replay_window.
CVE-2017-7184
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c282222a45 upstream.
Dmitry reports following splat:
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 0 PID: 13059 Comm: syz-executor1 Not tainted 4.10.0-rc7-next-20170207 #1
[..]
spin_lock_bh include/linux/spinlock.h:304 [inline]
xfrm_policy_flush+0x32/0x470 net/xfrm/xfrm_policy.c:963
xfrm_policy_fini+0xbf/0x560 net/xfrm/xfrm_policy.c:3041
xfrm_net_init+0x79f/0x9e0 net/xfrm/xfrm_policy.c:3091
ops_init+0x10a/0x530 net/core/net_namespace.c:115
setup_net+0x2ed/0x690 net/core/net_namespace.c:291
copy_net_ns+0x26c/0x530 net/core/net_namespace.c:396
create_new_namespaces+0x409/0x860 kernel/nsproxy.c:106
unshare_nsproxy_namespaces+0xae/0x1e0 kernel/nsproxy.c:205
SYSC_unshare kernel/fork.c:2281 [inline]
Problem is that when we get error during xfrm_net_init we will call
xfrm_policy_fini which will acquire xfrm_policy_lock before it was
initialized. Just move it around so locks get set up first.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Fixes: 283bc9f35b ("xfrm: Namespacify xfrm state/policy locks")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6207119444 upstream.
With this reproducer:
struct sockaddr_alg alg = {
.salg_family = 0x26,
.salg_type = "hash",
.salg_feat = 0xf,
.salg_mask = 0x5,
.salg_name = "digest_null",
};
int sock, sock2;
sock = socket(AF_ALG, SOCK_SEQPACKET, 0);
bind(sock, (struct sockaddr *)&alg, sizeof(alg));
sock2 = accept(sock, NULL, NULL);
setsockopt(sock, SOL_ALG, ALG_SET_KEY, "\x9b\xca", 2);
accept(sock2, NULL, NULL);
==== 8< ======== 8< ======== 8< ======== 8< ====
one can immediatelly see an UBSAN warning:
UBSAN: Undefined behaviour in crypto/algif_hash.c:187:7
variable length array bound value 0 <= 0
CPU: 0 PID: 15949 Comm: syz-executor Tainted: G E 4.4.30-0-default #1
...
Call Trace:
...
[<ffffffff81d598fd>] ? __ubsan_handle_vla_bound_not_positive+0x13d/0x188
[<ffffffff81d597c0>] ? __ubsan_handle_out_of_bounds+0x1bc/0x1bc
[<ffffffffa0e2204d>] ? hash_accept+0x5bd/0x7d0 [algif_hash]
[<ffffffffa0e2293f>] ? hash_accept_nokey+0x3f/0x51 [algif_hash]
[<ffffffffa0e206b0>] ? hash_accept_parent_nokey+0x4a0/0x4a0 [algif_hash]
[<ffffffff8235c42b>] ? SyS_accept+0x2b/0x40
It is a correct warning, as hash state is propagated to accept as zero,
but creating a zero-length variable array is not allowed in C.
Fix this as proposed by Herbert -- do "?: 1" on that site. No sizeof or
similar happens in the code there, so we just allocate one byte even
though we do not use the array.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net> (maintainer:CRYPTO API)
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8aac7f3436 upstream.
fbcon can deal with vc_hi_font_mask (the upper 256 chars) and adjust
the vc attrs dynamically when vc_hi_font_mask is changed at
fbcon_init(). When the vc_hi_font_mask is set, it remaps the attrs in
the existing console buffer with one bit shift up (for 9 bits), while
it remaps with one bit shift down (for 8 bits) when the value is
cleared. It works fine as long as the font gets updated after fbcon
was initialized.
However, we hit a bizarre problem when the console is switched to
another fb driver (typically from vesafb or efifb to drmfb). At
switching to the new fb driver, we temporarily rebind the console to
the dummy console, then rebind to the new driver. During the
switching, we leave the modified attrs as is. Thus, the new fbcon
takes over the old buffer as if it were to contain 8 bits chars
(although the attrs are still shifted for 9 bits), and effectively
this results in the yellow color texts instead of the original white
color, as found in the bugzilla entry below.
An easy fix for this is to re-adjust the attrs before leaving the
fbcon at con_deinit callback. Since the code to adjust the attrs is
already present in the current fbcon code, in this patch, we simply
factor out the relevant code, and call it from fbcon_deinit().
Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=1000619
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 24835e442f upstream.
When writing the generic nonblocking commit code I assumed that
through clever lifetime management I can assure that the completion
(stored in drm_crtc_commit) only gets freed after it is completed. And
that worked.
I also wanted to make nonblocking helpers resilient against driver
bugs, by having timeouts everywhere. And that worked too.
Unfortunately taking boths things together results in oopses :( Well,
at least sometimes: What seems to happen is that the drm event hangs
around forever stuck in limbo land. The nonblocking helpers eventually
time out, move on and release it. Now the bug I tested all this
against is drivers that just entirely fail to deliver the vblank
events like they should, and in those cases the event is simply
leaked. But what seems to happen, at least sometimes, on i915 is that
the event is set up correctly, but somohow the vblank fails to fire in
time. Which means the event isn't leaked, it's still there waiting for
eventually a vblank to fire. That tends to happen when re-enabling the
pipe, and then the trap springs and the kernel oopses.
The correct fix here is simply to refcount the crtc commit to make
sure that the event sticks around even for drivers which only
sometimes fail to deliver vblanks for some arbitrary reasons. Since
crtc commits are already refcounted that's easy to do.
References: https://bugs.freedesktop.org/show_bug.cgi?id=96781
Cc: Jim Rees <rees@umich.edu>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161221102331.31033-1-daniel.vetter@ffwll.ch
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c74fd80f2f upstream.
Revert the main part of commit:
af42b8d12f ("xen: fix MSI setup and teardown for PV on HVM guests")
That commit introduced reading the pci device's msi message data to see
if a pirq was previously configured for the device's msi/msix, and re-use
that pirq. At the time, that was the correct behavior. However, a
later change to Qemu caused it to call into the Xen hypervisor to unmap
all pirqs for a pci device, when the pci device disables its MSI/MSIX
vectors; specifically the Qemu commit:
c976437c7dba9c7444fb41df45468968aaa326ad
("qemu-xen: free all the pirqs for msi/msix when driver unload")
Once Qemu added this pirq unmapping, it was no longer correct for the
kernel to re-use the pirq number cached in the pci device msi message
data. All Qemu releases since 2.1.0 contain the patch that unmaps the
pirqs when the pci device disables its MSI/MSIX vectors.
This bug is causing failures to initialize multiple NVMe controllers
under Xen, because the NVMe driver sets up a single MSIX vector for
each controller (concurrently), and then after using that to talk to
the controller for some configuration data, it disables the single MSIX
vector and re-configures all the MSIX vectors it needs. So the MSIX
setup code tries to re-use the cached pirq from the first vector
for each controller, but the hypervisor has already given away that
pirq to another controller, and its initialization fails.
This is discussed in more detail at:
https://lists.xen.org/archives/html/xen-devel/2017-01/msg00447.html
Fixes: af42b8d12f ("xen: fix MSI setup and teardown for PV on HVM guests")
Signed-off-by: Dan Streetman <dan.streetman@canonical.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ad0a45fd9c upstream.
If a given cpu is not in cpu_present and cpu hotplug
is disabled, arch can skip setting up the cpu_dev.
Arch cpuidle driver should pass correct cpu mask
for registration, but failing to do so by the driver
causes error to propagate and crash like this:
[ 30.076045] Unable to handle kernel paging request for data at address 0x00000048
[ 30.076100] Faulting instruction address: 0xc0000000007b2f30
cpu 0x4d: Vector: 300 (Data Access) at [c000003feb18b670]
pc: c0000000007b2f30: kobject_get+0x20/0x70
lr: c0000000007b3c94: kobject_add_internal+0x54/0x3f0
sp: c000003feb18b8f0
msr: 9000000000009033
dar: 48
dsisr: 40000000
current = 0xc000003fd2ed8300
paca = 0xc00000000fbab500 softe: 0 irq_happened: 0x01
pid = 1, comm = swapper/0
Linux version 4.11.0-rc2-svaidy+ (sv@sagarika) (gcc version 6.2.0
20161005 (Ubuntu 6.2.0-5ubuntu12) ) #10 SMP Sun Mar 19 00:08:09 IST 2017
enter ? for help
[c000003feb18b960] c0000000007b3c94 kobject_add_internal+0x54/0x3f0
[c000003feb18b9f0] c0000000007b43a4 kobject_init_and_add+0x64/0xa0
[c000003feb18ba70] c000000000e284f4 cpuidle_add_sysfs+0xb4/0x130
[c000003feb18baf0] c000000000e26038 cpuidle_register_device+0x118/0x1c0
[c000003feb18bb30] c000000000e26c48 cpuidle_register+0x78/0x120
[c000003feb18bbc0] c00000000168fd9c powernv_processor_idle_init+0x110/0x1c4
[c000003feb18bc40] c00000000000cff8 do_one_initcall+0x68/0x1d0
[c000003feb18bd00] c0000000016242f4 kernel_init_freeable+0x280/0x360
[c000003feb18bdc0] c00000000000d864 kernel_init+0x24/0x160
[c000003feb18be30] c00000000000b4e8 ret_from_kernel_thread+0x5c/0x74
Validating cpu_dev fixes the crash and reports correct error message like:
[ 30.163506] Failed to register cpuidle device for cpu136
[ 30.173329] Registration of powernv driver failed.
Signed-off-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
[ rjw: Comment massage ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c46f09175d upstream.
Commit <f2e767bb5d6e> ("mpt3sas: Force request partial completion
alignment") was not considering the case of commands not operating on
logical block size units (e.g. REQ_OP_ZONE_REPORT and its 64B aligned
partial replies). In this case, forcing alignment of resid to the device
logical block size can break the command result, e.g. in the case of
REQ_OP_ZONE_REPORT, the exact number of zone reported by the device.
Move the partial completion alignement check of mpt3sas to a generic
implementation in sd_done(). The check is added within the default
section of the initial req_op() switch case so that the report and reset
zone commands are ignored. In addition, as sd_done() is not called for
passthrough requests, resid corrections are not done as intended by the
initial mpt3sas patch.
Fixes: f2e767bb5d ("mpt3sas: Force request partial completion alignment")
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0134ed4fb9 upstream.
Jeff Moyer reports:
With a device dax alignment of 4KB or 2MB, I get sigbus when running
the attached fio job file for the current kernel (4.11.0-rc1+). If
I specify an alignment of 1GB, it works.
I turned on debug output, and saw that it was failing in the huge
fault code.
dax dax1.0: dax_open
dax dax1.0: dax_mmap
dax dax1.0: dax_dev_huge_fault: fio: write (0x7f08f0a00000 -
dax dax1.0: __dax_dev_pud_fault: phys_to_pgoff(0xffffffffcf60
dax dax1.0: dax_release
fio config for reproduce:
[global]
ioengine=dev-dax
direct=0
filename=/dev/dax0.0
bs=2m
[write]
rw=write
[read]
stonewall
rw=read
The driver fails to fallback when taking a fault that is larger than
the device alignment, or handling a larger fault when a smaller
mapping is already established. While we could support larger
mappings for a device with a smaller alignment, that change is
too large for the immediate fix. The simplest change is to force
fallback until the fault size matches the alignment.
Fixes: dee4107924 ("/dev/dax, core: file operations and dax-mmap")
Cc: <stable@vger.kernel.org>
Reported-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b581a5854e upstream.
Since ceph.git commit 4e28f9e63644 ("osd/OSDMap: clear osd_info,
osd_xinfo on osd deletion"), weight is set to IN when OSD is deleted.
This changes the result of applying an incremental for clients, not
just OSDs. Because CRUSH computations are obviously affected,
pre-4e28f9e63644 servers disagree with post-4e28f9e63644 clients on
object placement, resulting in misdirected requests.
Mirrors ceph.git commit a6009d1039a55e2c77f431662b3d6cc5a8e8e63f.
Fixes: 930c532869 ("libceph: apply new_state before new_up_client on incrementals")
Link: http://tracker.ceph.com/issues/19122
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2602b740e4 upstream.
Commit 1552011150 ("mmc: core: Further fix thread wake-up") allowed a
queue to release the host with is_waiting_last_req set to true. A queue
waiting to claim the host will not reset it, which can result in the
queue getting stuck in a loop.
Fixes: 1552011150 ("mmc: core: Further fix thread wake-up")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e030d5ce9 upstream.
When we close a channel that has been rescinded, we will leak memory since
vmbus_teardown_gpadl() returns an error. Fix this so that we can properly
cleanup the memory allocated to the ring buffers.
Fixes: ccb61f8a99 ("Drivers: hv: vmbus: Fix a rescind handling bug")
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a5476020a upstream.
If we cannot allocate memory for the channel, free the relid
associated with the channel.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e609ccef52 upstream.
Output 'activation' may fail for the reasons of the output driver,
for example, if msc's buffer is not allocated. We forget, however,
to drop the module reference in this case. So each attempt at
activation in this case leaks a reference, preventing the module
from ever unloading.
This patch adds the missing module_put() in the activation error
path.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd9cb405e0 upstream.
In journal_init_common(), if we failed to allocate the j_wbuf array, or
if we failed to create the buffer_head for the journal superblock, we
leaked the memory allocated for the revocation tables. Fix this.
Fixes: f0c9fd5458
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit abda288bb2 upstream.
The OF device table must be terminated, otherwise we'll be walking past it
and into areas unknown.
Fixes: 0cad855fbd ("auxdisplay: img-ascii-lcd: driver for simple ASCII...")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07fef36234 upstream.
With posix timers having become optional, we get a build error with
the cpts time sync option of the CPSW driver:
drivers/net/ethernet/ti/cpts.c: In function 'cpts_find_ts':
drivers/net/ethernet/ti/cpts.c:291:23: error: implicit declaration of function 'ptp_classify_raw';did you mean 'ptp_classifier_init'? [-Werror=implicit-function-declaration]
This adds a hard dependency on PTP_CLOCK to avoid the problem, as
building it without PTP support makes no sense anyway.
Fixes: baa73d9e47 ("posix-timers: Make them configurable")
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a05d4fd917 upstream.
The net_cls controller controls the classid field of each socket which
is associated with the cgroup. Because the classid is per-socket
attribute, when a task migrates to another cgroup or the configured
classid of the cgroup changes, the controller needs to walk all
sockets and update the classid value, which was implemented by
3b13758f51 ("cgroups: Allow dynamically changing net_classid").
While the approach is not scalable, migrating tasks which have a lot
of fds attached to them is rare and the cost is born by the ones
initiating the operations. However, for simplicity, both the
migration and classid config change paths call update_classid() which
scans all fds of all tasks in the target css. This is an overkill for
the migration path which only needs to cover a much smaller subset of
tasks which are actually getting migrated in.
On cgroup v1, this can lead to unexpected scalability issues when one
tries to migrate a task or process into a net_cls cgroup which already
contains a lot of fds. Even if the migration traget doesn't have many
to get scanned, update_classid() ends up scanning all fds in the
target cgroup which can be extremely numerous.
Unfortunately, on cgroup v2 which doesn't use net_cls, the problem is
even worse. Before bfc2cf6f61 ("cgroup: call subsys->*attach() only
for subsystems which are actually affected by migration"), cgroup core
would call the ->css_attach callback even for controllers which don't
see actual migration to a different css.
As net_cls is always disabled but still mounted on cgroup v2, whenever
a process is migrated on the cgroup v2 hierarchy, net_cls sees
identity migration from root to root and cgroup core used to call
->css_attach callback for those. The net_cls ->css_attach ends up
calling update_classid() on the root net_cls css to which all
processes on the system belong to as the controller isn't used. This
makes any cgroup v2 migration O(total_number_of_fds_on_the_system)
which is horrible and easily leads to noticeable stalls triggering RCU
stall warnings and so on.
The worst symptom is already fixed in upstream by bfc2cf6f61
("cgroup: call subsys->*attach() only for subsystems which are
actually affected by migration"); however, backporting that commit is
too invasive and we want to avoid other cases too.
This patch updates net_cls's cgrp_attach() to iterate fds of only the
processes which are actually getting migrated. This removes the
surprising migration cost which is dependent on the total number of
fds in the target cgroup. As this leaves write_classid() the only
user of update_classid(), open-code the helper into write_classid().
Reported-by: David Goode <dgoode@fb.com>
Fixes: 3b13758f51 ("cgroups: Allow dynamically changing net_classid")
Cc: Nina Schiff <ninasc@fb.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff010472fb upstream.
On CPU online the cpufreq core restores the previous governor (or
the previous "policy" setting for ->setpolicy drivers), but it does
not restore the min/max limits at the same time, which is confusing,
inconsistent and real pain for users who set the limits and then
suspend/resume the system (using full suspend), in which case the
limits are reset on all CPUs except for the boot one.
Fix this by making cpufreq_online() restore the limits when an inactive
policy is brought online.
The commit log and patch are inspired from Rafael's earlier work.
Reported-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit afd0e5a876 upstream.
If kernel image extends across alignment boundary, existing
code increases the KASLR offset by size of kernel image. The
offset is masked after resizing. There are cases, where after
masking, we may still have kernel image extending across
boundary. This eventually results in only 2MB block getting
mapped while creating the page tables. This results in data aborts
while accessing unmapped regions during second relocation (with
kaslr offset) in __primary_switch. To fix this problem, round up the
kernel image size, by swapper block size, before adding it for
correction.
For example consider below case, where kernel image still crosses
1GB alignment boundary, after masking the offset, which is fixed
by rounding up kernel image size.
SWAPPER_TABLE_SHIFT = 30
Swapper using section maps with section size 2MB.
CONFIG_PGTABLE_LEVELS = 3
VA_BITS = 39
_text : 0xffffff8008080000
_end : 0xffffff800aa1b000
offset : 0x1f35600000
mask = ((1UL << (VA_BITS - 2)) - 1) & ~(SZ_2M - 1)
(_text + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7c
(_end + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d
offset after existing correction (before mask) = 0x1f37f9b000
(_text + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d
(_end + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d
offset (after mask) = 0x1f37e00000
(_text + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7c
(_end + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d
new offset w/ rounding up = 0x1f38000000
(_text + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d
(_end + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d
Fixes: f80fb3a3d5 ("arm64: add support for kernel ASLR")
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Signed-off-by: Srinivas Ramana <sramana@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 60b89f1928 upstream.
On some DDR controllers, compatible with the sama5d3 one,
the sequence to enter/exit/re-enter the self-refresh mode adds
more constrains than what is currently written in the at91_idle
driver. An actual access to the DDR chip is needed between exit
and re-enter of this mode which is somehow difficult to implement.
This sequence can completely hang the SoC. It is particularly
experienced on parts which embed a L2 cache if the code run
between IDLE calls fits in it...
Moreover, as the intention is to enter and exit pretty rapidly
from IDLE, the power-down mode is a good candidate.
So now we use power-down instead of self-refresh. As we can
simplify the code for sama5d3 compatible DDR controllers,
we instantiate a new sama5d3_ddr_standby() function.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Fixes: 017b5522d5 ("ARM: at91: Add new binding for sama5d3-ddramc")
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9e10889a31 upstream.
This reverts commit cab4328268 ("ARM: at91/dt: sama5d2: Use new
compatible for ohci node")
It depends from commit 7150bc9b4d ("usb: ohci-at91: Forcibly suspend
ports while USB suspend") which was reverted and implemented
differently. With the new implementation, the compatible string must
remain the same.
The compatible string introduced by this commit has been used in the
default SAMA5D2 dtsi starting from Linux 4.8. As it has never been
working correctly in an official release, removing it should not be
breaking the stability rules.
Fixes: cab4328268 ("ARM: at91/dt: sama5d2: Use new compatible for ohci node")
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd37a296a9 upstream.
For some unknown reasons, in some cases, FLPD cache invalidation doesn't
work properly with SYSMMU v5 controllers found in Exynos5433 SoCs. This
can be observed by a firmware crash during initialization phase of MFC
video decoder available in the mentioned SoCs when IOMMU support is
enabled. To workaround this issue perform a full TLB/FLPD invalidation
in case of replacing any first level page descriptors in case of SYSMMU v5.
Fixes: 740a01eee9 ("iommu/exynos: Add support for v5 SYSMMU")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d2aa6b814 upstream.
Documentation specifies that SYSMMU should be in blocked state while
performing TLB/FLPD cache invalidation, so add needed calls to
sysmmu_block/unblock.
Fixes: 66a7ed84b3 ("iommu/exynos: Apply workaround of caching fault page table entries")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1914f0cd20 upstream.
This was broken in commit cd979883b9 ("xen/acpi-processor:
fix enabling interrupts on syscore_resume"). do_suspend (from
xen/manage.c) and thus xen_resume_notifier never get called on
the initial-domain at resume (it is if running as guest.)
The rationale for the breaking change was that upload_pm_data()
potentially does blocking work in syscore_resume(). This patch
addresses the original issue by scheduling upload_pm_data() to
execute in workqueue context.
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Based-on-patch-by: Konrad Wilk <konrad.wilk@oracle.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Ankur Arora <ankur.a.arora@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 65b1adebfe upstream.
The intent of the original warning is make sure that the mdev vendor
driver has removed any group notifiers at the point where the group
is closed by the user. Theoretically this would be through an
orderly shutdown where any devices are release prior to the group
release. We can't always count on an orderly shutdown, the user can
close the group before the notifier can be removed or the user task
might be killed. We'd like to add this sanity test when the group is
idle and the only references are from the devices within the group
themselves, but we don't have a good way to do that. Instead check
both when the group itself is removed and when the group is opened.
A bit later than we'd prefer, but better than the current over
aggressive approach.
Fixes: ccd46dbae7 ("vfio: support notifier chain in vfio_group")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Cc: Jike Song <jike.song@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b53cf9815 upstream.
Filesystem encryption ostensibly supported revoking a keyring key that
had been used to "unlock" encrypted files, causing those files to become
"locked" again. This was, however, buggy for several reasons, the most
severe of which was that when key revocation happened to be detected for
an inode, its fscrypt_info was immediately freed, even while other
threads could be using it for encryption or decryption concurrently.
This could be exploited to crash the kernel or worse.
This patch fixes the use-after-free by removing the code which detects
the keyring key having been revoked, invalidated, or expired. Instead,
an encrypted inode that is "unlocked" now simply remains unlocked until
it is evicted from memory. Note that this is no worse than the case for
block device-level encryption, e.g. dm-crypt, and it still remains
possible for a privileged user to evict unused pages, inodes, and
dentries by running 'sync; echo 3 > /proc/sys/vm/drop_caches', or by
simply unmounting the filesystem. In fact, one of those actions was
already needed anyway for key revocation to work even somewhat sanely.
This change is not expected to break any applications.
In the future I'd like to implement a real API for fscrypt key
revocation that interacts sanely with ongoing filesystem operations ---
waiting for existing operations to complete and blocking new operations,
and invalidating and sanitizing key material and plaintext from the VFS
caches. But this is a hard problem, and for now this bug must be fixed.
This bug affected almost all versions of ext4, f2fs, and ubifs
encryption, and it was potentially reachable in any kernel configured
with encryption support (CONFIG_EXT4_ENCRYPTION=y,
CONFIG_EXT4_FS_ENCRYPTION=y, CONFIG_F2FS_FS_ENCRYPTION=y, or
CONFIG_UBIFS_FS_ENCRYPTION=y). Note that older kernels did not use the
shared fs/crypto/ code, but due to the potential security implications
of this bug, it may still be worthwhile to backport this fix to them.
Fixes: b7236e21d5 ("ext4 crypto: reorganize how we store keys in the inode")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Acked-by: Michael Halcrow <mhalcrow@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c468447f4 upstream.
The CCP driver generally uses a round-robin approach when
assigning operations to available CCPs. For the DMA engine,
however, the DMA mappings of the SGs are associated with a
specific CCP. When an IOMMU is enabled, the IOMMU is
programmed based on this specific device.
If the DMA operations are not performed by that specific
CCP then addressing errors and I/O page faults will occur.
Update the CCP driver to allow a specific CCP device to be
requested for an operation and use this in the DMA engine
support.
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6be3b6cce1 upstream.
In the 'commit ebee76f7fa ("ath10k: allow setting coverage class")',
it inherits the design and the address offset from ath9k, but the address
is not applicable to QCA6174, which leads to a random crash while doing the
resume() operation, since the set_coverage_class.ops will be called from
ieee80211_reconfig() when resume() (if the wow is not configured).
Fix the incorrect address offset here to avoid the random crash.
Verified on QCA6174/hw3.0 with firmware WLAN.RM.4.4-00022-QCARMSWPZ-2.
kvalo: this also seems to fix a regression with firmware restart.
Fixes: ebee76f7fa ("ath10k: allow setting coverage class")
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e841d3eb9 upstream.
When PCIe FLR support was added, much of the remove/release code for
PCIe was migrated to ->down_dev(), but ->down_dev() is never called for
device removal. Let's refactor the cleanup to be done in both cases.
Also, drop the comments above mwifiex_cleanup_pcie(), because they were
clearly wrong, and it's better to have clear and obvious code than to
detail the code steps in comments anyway.
Fixes: 4c5dae59d2 ("mwifiex: add PCIe function level reset support")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ac8616e4c8 upstream.
The MP style clocks support an mux with pre-dividers. While the driver
correctly accounted for them in the .determine_rate callback, it did
not in the .recalc_rate and .set_rate callbacks.
This means when calculating the factors in the .set_rate callback, they
would be off by a factor of the active pre-divider. Same goes for
reading back the clock rate after it is set.
Fixes: 2ab836db50 ("clk: sunxi-ng: Add M-P factor clock support")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c75704ebc upstream.
After commit e9afc74629 ("hwrng: geode - Use linux/io.h instead of
asm/io.h") the geode-rng driver uses devres with pci_dev->dev to keep
track of resources, but does not actually register a PCI driver. This
results in the following issues:
1. The driver leaks memory because the driver does not attach to a
device. The driver only uses the PCI device as a reference. devm_*()
functions will release resources on driver detach, which the geode-rng
driver will never do. As a result,
2. The driver cannot be reloaded because there is always a use of the
ioport and region after the first load of the driver.
Revert the changes made by e9afc74629 ("hwrng: geode - Use linux/io.h
instead of asm/io.h").
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Fixes: 6e9b5e7688 ("hwrng: geode - Migrate to managed API")
Cc: Matt Mackall <mpm@selenic.com>
Cc: Corentin LABBE <clabbe.montjoie@gmail.com>
Cc: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Cc: Wei Yongjun <weiyongjun1@huawei.com>
Cc: linux-crypto@vger.kernel.org
Cc: linux-geode@lists.infradead.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 69db700931 upstream.
After commit 31b2a73c9c ("hwrng: amd - Migrate to managed API"), the
amd-rng driver uses devres with pci_dev->dev to keep track of resources,
but does not actually register a PCI driver. This results in the
following issues:
1. The message
WARNING: CPU: 2 PID: 621 at drivers/base/dd.c:349 driver_probe_device+0x38c
is output when the i2c_amd756 driver loads and attempts to register a PCI
driver. The PCI & device subsystems assume that no resources have been
registered for the device, and the WARN_ON() triggers since amd-rng has
already do so.
2. The driver leaks memory because the driver does not attach to a
device. The driver only uses the PCI device as a reference. devm_*()
functions will release resources on driver detach, which the amd-rng
driver will never do. As a result,
3. The driver cannot be reloaded because there is always a use of the
ioport and region after the first load of the driver.
Revert the changes made by 31b2a73c9c ("hwrng: amd - Migrate to managed
API").
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Fixes: 31b2a73c9c ("hwrng: amd - Migrate to managed API").
Cc: Matt Mackall <mpm@selenic.com>
Cc: Corentin LABBE <clabbe.montjoie@gmail.com>
Cc: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Cc: Wei Yongjun <weiyongjun1@huawei.com>
Cc: linux-crypto@vger.kernel.org
Cc: linux-geode@lists.infradead.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 027fb89e61 upstream.
Disabling interrupts for even a millisecond can cause problems for some
devices. That can happen when Intel host controllers wait for the present
state to propagate.
The spin lock is not necessary here. Anything that is racing with changes
to the I/O state is already broken. The mmc core already provides
synchronization via "claiming" the host.
Although the spin lock probably should be removed from the code paths that
lead to this point, such a patch would touch too much code to be suitable
for stable trees. Consequently, for this patch, just drop the spin lock
while waiting.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e2ebfb2142 upstream.
Disabling interrupts for even a millisecond can cause problems for some
devices. That can happen when sdhci changes clock frequency because it
waits for the clock to become stable under a spin lock.
The spin lock is not necessary here. Anything that is racing with changes
to the I/O state is already broken. The mmc core already provides
synchronization via "claiming" the host.
Although the spin lock probably should be removed from the code paths that
lead to this point, such a patch would touch too much code to be suitable
for stable trees. Consequently, for this patch, just drop the spin lock
while waiting.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 16681037e7 upstream.
sdhci_arasan_get_timeout_clock() divides the frequency it has with (1 <<
(13 + divisor)).
However, the divisor is not some Arasan-specific value, but instead is
just the Data Timeout Counter Value from the SDHCI Timeout Control
Register.
Applying it here like this is wrong as the sdhci driver already takes
that value into account when calculating timeouts, and in fact it *sets*
that register value based on how long a timeout is wanted.
Additionally, sdhci core interprets the .get_timeout_clock callback
return value as if it were read from hardware registers, i.e. the unit
should be kHz or MHz depending on SDHCI_TIMEOUT_CLK_UNIT capability bit.
This bit is set at least on the tested Zynq-7000 SoC.
With the tested hardware (SDHCI_TIMEOUT_CLK_UNIT set) this results in
too high a timeout clock rate being reported, causing the core to use
longer-than-needed timeouts. Additionally, on a partitioned MMC
(therefore having erase_group_def bit set) mmc_calc_max_discard()
disables discard support as it looks like controller does not support
the long timeouts needed for that.
Do not apply the extra divisor and return the timeout clock in the
expected unit.
Tested with a Zynq-7000 SoC and a partitioned Toshiba THGBMAG5A1JBAWR
eMMC card.
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Fixes: e3ec3a3d11 ("mmc: arasan: Add driver for Arasan SDHCI")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2ce0c7b655 upstream.
The SDHCI controller in the SAMA5D2 chip requires a valid voltage set
in the power control register, otherwise commands will fail with a
timeout error.
When using the regulator framework to specify the regulator used by the
mmc device, the voltage is not configured, and it is not possible to use
the connected device.
Implement a custom 'set_power' function for this specific hardware, that
configures the voltage in the register in all cases.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b52330bbf upstream.
What started as a rather straightforward race condition reported by
Dmitry using the syzkaller fuzzer ended up revealing some major
problems with how the audit subsystem managed its netlink sockets and
its connection with the userspace audit daemon. Fixing this properly
had quite the cascading effect and what we are left with is this rather
large and complicated patch. My initial goal was to try and decompose
this patch into multiple smaller patches, but the way these changes
are intertwined makes it difficult to split these changes into
meaningful pieces that don't break or somehow make things worse for
the intermediate states.
The patch makes a number of changes, but the most significant are
highlighted below:
* The auditd tracking variables, e.g. audit_sock, are now gone and
replaced by a RCU/spin_lock protected variable auditd_conn which is
a structure containing all of the auditd tracking information.
* We no longer track the auditd sock directly, instead we track it
via the network namespace in which it resides and we use the audit
socket associated with that namespace. In spirit, this is what the
code was trying to do prior to this patch (at least I think that is
what the original authors intended), but it was done rather poorly
and added a layer of obfuscation that only masked the underlying
problems.
* Big backlog queue cleanup, again. In v4.10 we made some pretty big
changes to how the audit backlog queues work, here we haven't changed
the queue design so much as cleaned up the implementation. Brought
about by the locking changes, we've simplified kauditd_thread() quite
a bit by consolidating the queue handling into a new helper function,
kauditd_send_queue(), which allows us to eliminate a lot of very
similar code and makes the looping logic in kauditd_thread() clearer.
* All netlink messages sent to auditd are now sent via
auditd_send_unicast_skb(). Other than just making sense, this makes
the lock handling easier.
* Change the audit_log_start() sleep behavior so that we never sleep
on auditd events (unchanged) or if the caller is holding the
audit_cmd_mutex (changed). Previously we didn't sleep if the caller
was auditd or if the message type fell between a certain range; the
type check was a poor effort of doing what the cmd_mutex check now
does. Richard Guy Briggs originally proposed not sleeping the
cmd_mutex owner several years ago but his patch wasn't acceptable
at the time. At least the idea lives on here.
* A problem with the lost record counter has been resolved. Steve
Grubb and I both happened to notice this problem and according to
some quick testing by Steve, this problem goes back quite some time.
It's largely a harmless problem, although it may have left some
careful sysadmins quite puzzled.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6d98ce0be5 upstream.
We concluded there may be a window where the idle wakeup code could get
to pnv_wakeup_tb_loss() (which clobbers non-volatile GPRs), but the
hardware may set SRR1[46:47] to 01b (no state loss) which would result
in the wakeup code failing to restore non-volatile GPRs.
I was not able to trigger this condition with trivial tests on real
hardware or simulator, but the ISA (at least 2.07) seems to allow for
it, and Gautham says that it can happen if there is an exception pending
when the sleep/winkle instruction is executed.
Fixes: 1706567117 ("powerpc/kvm: make hypervisor state restore a function")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b9cf625d6e upstream.
If ext4_convert_inline_data() was called on a directory with inline
data, the filesystem was left in an inconsistent state (as considered by
e2fsck) because the file size was not increased to cover the new block.
This happened because the inode was not marked dirty after i_disksize
was updated. Fix this by marking the inode dirty at the end of
ext4_finish_convert_inline_dir().
This bug was probably not noticed before because most users mark the
inode dirty afterwards for other reasons. But if userspace executed
FS_IOC_SET_ENCRYPTION_POLICY with invalid parameters, as exercised by
'kvm-xfstests -c adv generic/396', then the inode was never marked dirty
after updating i_disksize.
Fixes: 3c47d54170
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a69645dde upstream.
Usually every parallel port will have a single pardev registered with
it. But ppdev driver is an exception. This userspace parallel port
driver allows to create multiple parrallel port devices for a single
parallel port. And as a result we were having a big warning like:
"sysfs: cannot create duplicate filename '/devices/parport0/ppdev0.0'".
And with that many parallel port printers stopped working.
We have been using the minor number as the id field while registering
a parralel port device with a parralel port. But when there are
multiple parrallel port device for one single parallel port, they all
tried to register with the same name like 'pardev0.0' and everything
started failing.
Use an incremented index as the id instead of the minor number.
Fixes: 8b7d3a9d90 ("ppdev: use new parport device model")
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1414656
Bugzilla: https://bugs.archlinux.org/task/52322
Tested-by: James Feeney <james@nurealm.net>
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 03270c6ac6 upstream.
Usually every parallel port will have a single pardev registered with
it. But ppdev driver is an exception. This userspace parallel port
driver allows to create multiple parrallel port devices for a single
parallel port. And as a result we were having a nice warning like:
"sysctl table check failed:
/dev/parport/parport0/devices/ppdev0/timeslice Sysctl already exists"
Use the same logic as used in parport_register_device() and register
the proc files only once for each parallel port.
Fixes: 6fa45a2268 ("parport: add device-model to parport subsystem")
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1414656
Bugzilla: https://bugs.archlinux.org/task/52322
Tested-by: James Feeney <james@nurealm.net>
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c6240cacdb upstream.
The driver still struggles with firmwares that do not replay to the OS
version request. It is safe not waiting for the replay. First, the driver
doesn't do anything with the replay second the connection is closed
immediately, hence the packet will be just safely discarded in case it
is received and last the driver won't get stuck if the firmware won't
reply.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a733ded50b upstream.
This patch fixes 'mei: synchronize irq before initiating a reset'
The patch had introduced a deadlock between irq thread and mei_reset()
as they are both holding the same device lock.
---> device_lock:
mei_reset()
<---- interrupt thread
device_lock
---> synchornize_irq()
wait on interrupt thread == (dead lock)
The fix is to call synchronize_irq
prior to call locked mei_reset function.
Fixes: f302bb0de6ac (mei: synchronize irq before initiating a reset)
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ff861f59f upstream.
Even if bus is not hot-pluggable, devices can be unbound from the
driver via sysfs, so we should not be using __exit annotations on
remove() methods. The only exception is drivers registered with
platform_driver_probe() which specifically disables sysfs bind/unbind
attributes.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3bec247474 upstream.
In function _hid_sensor_power_state(), when hid_sensor_read_poll_value()
is called, sensor's all properties will be updated by the value from
sensor hardware/firmware.
In some implementation, sensor hardware/firmware will do a power cycle
during S3. In this case, after resume, once hid_sensor_read_poll_value()
is called, sensor's all properties which are kept by driver during S3
will be changed to default value.
But instead, if a set feature function is called first, sensor
hardware/firmware will be recovered to the last status. So change the
sensor_hub_set_feature() calling order to behind of set feature function
to avoid sensor properties lose.
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c42f821861 upstream.
Use the IS_ENABLED() helper macro to ensure that the configfs group is
initialized either when configfs is built-in or when configfs is built as a
module. Otherwise software device creation will result in undefined
behaviour when configfs is built as a module since the configfs group for
the device not properly initialized.
Similar to commit b2f0c09664 ("iio: sw-trigger: Fix config group
initialization").
Fixes: 0f3a8c3f34 ("iio: Add support for creating IIO devices via configfs")
Reported-by: Miguel Robles <miguel.robles@farole.net>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e83bb3e6f3 upstream.
The tiadc_irq_h(int irq, void *private) function is handling FIFO
overruns by clearing flags, disabling and enabling the ADC to
recover.
If the ADC is running in continuous mode a FIFO overrun happens
regularly. If the disabling of the ADC happens concurrently with
a new conversion. It might happen that the enabling of the ADC
is ignored by the hardware. This stops the ADC permanently. No
more interrupts are triggered.
According to the AM335x Reference Manual (SPRUH73H October 2011 -
Revised April 2013 - Chapter 12.4 and 12.5) it is necessary to
check the ADC FSM bits in REG_ADCFSM before enabling the ADC
again. Because the disabling of the ADC is done right after the
current conversion has been finished.
To trigger this bug it is necessary to run the ADC in continuous
mode. The ADC values of all channels need to be read in an endless
loop. The bug appears within the first 6 hours (~5.4 million
handled FIFO overruns). The user space application will hang on
reading new values from the character device.
Fixes: ca9a563805 ("iio: ti_am335x_adc: Add continuous sampling support")
Signed-off-by: Michael Engl <michael.engl@wjw-solutions.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 773dc11875 upstream.
HS400-ES devices fail to initialize with the following error messages.
mmc1: power class selection to bus width 8 ddr 0 failed
mmc1: error -110 whilst initialising MMC card
This was seen on Samsung Chromebook Plus. Code analysis points to
commit 3d4ef32975 ("mmc: core: fix multi-bit bus width without
high-speed mode"), which attempts to set the bus width for all but
HS200 devices unconditionally. However, for HS400-ES, the bus width
is already selected.
Cc: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Brian Norris <briannorris@chromium.org>
Fixes: 3d4ef32975 ("mmc: core: fix multi-bit bus width ...")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chip.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea90e0dc8c upstream.
Sowmini pointed out Dmitry's RTNL deadlock report to me, and it turns out
to be perfectly accurate - there are various error paths that miss unlock
of the RTNL.
To fix those, change the locking a bit to not be conditional in all those
nl80211_prepare_*_dump() functions, but make those require the RTNL to
start with, and fix the buggy error paths. This also let me use sparse
(by appropriately overriding the rtnl_lock/rtnl_unlock functions) to
validate the changes.
Reported-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 181302dc72 upstream.
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.
Fixes: 53f3a9e26e ("mmc: USB SD Host Controller (USHC) driver")
Cc: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit daf229b159 upstream.
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.
Note that the dereference happens in the start callback which is called
during probe.
Fixes: de520b8bd5 ("uwb: add HWA radio controller driver")
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4ce362711d upstream.
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.
Note that the dereference happens in the cmd and wait_init_done
callbacks which are called during probe.
Fixes: 1ba47da527 ("uwb: add the i1480 DFU driver")
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e47c53503 upstream.
Make sure to initialise the return value to avoid having allocation
failures going unnoticed when allocating interrupt-endpoint resources.
This prevents use-after-free or worse when the device is later unbound.
Fixes: dbf3e7f654 ("Implement an ioctl to support the USMTMC-USB488 READ_STATUS_BYTE operation.")
Cc: Dave Penkler <dpenkler@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 687e0687f7 upstream.
USBTMC devices are required to have a bulk-in and a bulk-out endpoint,
but the driver failed to verify this, something which could lead to the
endpoint addresses being taken from uninitialised memory.
Make sure to zero all private data as part of allocation, and add the
missing endpoint sanity check.
Note that this also addresses a more recently introduced issue, where
the interrupt-in-presence flag would also be uninitialised whenever the
optional interrupt-in endpoint is not present. This in turn could lead
to an interrupt urb being allocated, initialised and submitted based on
uninitialised values.
Fixes: dbf3e7f654 ("Implement an ioctl to support the USMTMC-USB488 READ_STATUS_BYTE operation.")
Fixes: 5b775f672c ("USB: add USB test and measurement class driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b2db29fbb upstream.
If usb_get_bos_descriptor() returns an error, usb->bos will be NULL.
Nevertheless, it is dereferenced unconditionally in
hub_set_initial_usb2_lpm_policy() if usb2_hw_lpm_capable is set.
This results in a crash.
usb 5-1: unable to get BOS descriptor
...
Unable to handle kernel NULL pointer dereference at virtual address 00000008
pgd = ffffffc00165f000
[00000008] *pgd=000000000174f003, *pud=000000000174f003,
*pmd=0000000001750003, *pte=00e8000001751713
Internal error: Oops: 96000005 [#1] PREEMPT SMP
Modules linked in: uinput uvcvideo videobuf2_vmalloc cmac [ ... ]
CPU: 5 PID: 3353 Comm: kworker/5:3 Tainted: G B 4.4.52 #480
Hardware name: Google Kevin (DT)
Workqueue: events driver_set_config_work
task: ffffffc0c3690000 ti: ffffffc0ae9a8000 task.ti: ffffffc0ae9a8000
PC is at hub_port_init+0xc3c/0xd10
LR is at hub_port_init+0xc3c/0xd10
...
Call trace:
[<ffffffc0007fbbfc>] hub_port_init+0xc3c/0xd10
[<ffffffc0007fbe2c>] usb_reset_and_verify_device+0x15c/0x82c
[<ffffffc0007fc5e0>] usb_reset_device+0xe4/0x298
[<ffffffbffc0e3fcc>] rtl8152_probe+0x84/0x9b0 [r8152]
[<ffffffc00080ca8c>] usb_probe_interface+0x244/0x2f8
[<ffffffc000774a24>] driver_probe_device+0x180/0x3b4
[<ffffffc000774e48>] __device_attach_driver+0xb4/0xe0
[<ffffffc000772168>] bus_for_each_drv+0xb4/0xe4
[<ffffffc0007747ec>] __device_attach+0xd0/0x158
[<ffffffc000775080>] device_initial_probe+0x24/0x30
[<ffffffc0007739d4>] bus_probe_device+0x50/0xe4
[<ffffffc000770bd0>] device_add+0x414/0x738
[<ffffffc000809fe8>] usb_set_configuration+0x89c/0x914
[<ffffffc00080a120>] driver_set_config_work+0xc0/0xf0
[<ffffffc000249bb8>] process_one_work+0x390/0x6b8
[<ffffffc00024abcc>] worker_thread+0x480/0x610
[<ffffffc000251a80>] kthread+0x164/0x178
[<ffffffc0002045d0>] ret_from_fork+0x10/0x40
Since we don't know anything about LPM capabilities without BOS descriptor,
don't attempt to enable LPM if it is not available.
Fixes: 890dae8867 ("xhci: Enable LPM support only for hardwired ...")
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0090114d33 upstream.
The CPPI 4.1 driver polls register to workaround the premature TX
interrupt issue, but it causes audio playback underrun when triggered in
Isoch transfers.
Isoch doesn't do back-to-back transfers, the TX should be done by the
time the next transfer is scheduled. So skip this polling workaround for
Isoch transfer.
Fixes: a655f481d8 ("usb: musb: musb_cppi41: handle pre-mature TX complete interrupt")
Reported-by: Alexandre Bailon <abailon@baylibre.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 03ace948a4 upstream.
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
This specifically fixes the NULL-pointer dereference when probing HWA HC
devices.
Fixes: df3654236e ("wusb: add the Wire Adapter (WA) core")
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b0addd3fa6 upstream.
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1dc56c52d2 upstream.
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should the probed device lack endpoints.
Note that this driver does not bind to any devices by default.
Fixes: ce21bfe603 ("USB: Add LVS Test device driver")
Cc: Pratyush Anand <pratyush.anand@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f259ca3eed upstream.
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
Note that the endpoint access that causes the NULL-deref is currently
only used for debugging purposes during probe so the oops only happens
when dynamic debugging is enabled. This means the driver could be
rewritten to continue to accept device with only two endpoints, should
such devices exist.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3243367b20 upstream.
Some USB 2.0 devices erroneously report millisecond values in
bInterval. The generic config code manages to catch most of them,
but in some cases it's not completely enough.
The case at stake here is a USB 2.0 braille device, which wants to
announce 10ms and thus sets bInterval to 10, but with the USB 2.0
computation that yields to 64ms. It happens that one can type fast
enough to reach this interval and get the device buffers overflown,
leading to problematic latencies. The generic config code does not
catch this case because the 64ms is considered a sane enough value.
This change thus adds a USB_QUIRK_LINEAR_FRAME_INTR_BINTERVAL quirk
to mark devices which actually report milliseconds in bInterval,
and marks Vario Ultra devices as needing it.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67b0503db9 upstream.
The buffer allocation for the firmware data was changed in
commit 43fab9793c ("[media] dvb-usb: don't use stack for firmware load")
but the same applies for the reset value.
Fixes: 43fab9793c ("[media] dvb-usb: don't use stack for firmware load")
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09424c50b7 upstream.
The streaming_maxburst module parameter is 0 offset (0..15)
so we must add 1 while using it for wBytesPerInterval
calculation for the SuperSpeed companion descriptor.
Without this host uvcvideo driver will always see the wrong
wBytesPerInterval for SuperSpeed uvc gadget and may not find
a suitable video interface endpoint.
e.g. for streaming_maxburst = 0 case it will always
fail as wBytePerInterval was evaluating to 0.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cdd7928df0 upstream.
The gadget code exports the bitfield for serial status changes
over the wire in its internal endianness. The fix is to convert
to little endian before sending it over the wire.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Tested-by: 家瑋 <momo1208@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e9f44eaae upstream.
Add Quectel UC15, UC20, EC21, and EC25. The EC20 is handled by
qcserial due to a USB VID/PID conflict with an existing Acer
device.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f307834e6 upstream.
A new Dell laptop needs to apply ALC269_FIXUP_DELL1_MIC_NO_PRESENCE to
fix the headset problem, and the pin definiton of this machine is not
in the pin quirk table yet, now adding it to the table.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f363a06642 upstream.
In the commit [15c75b09f8: ALSA: ctxfi: Fallback DMA mask to 32bit],
I forgot to put "!" at dam_set_mask() call check in cthw20k1.c (while
cthw20k2.c is OK). This patch fixes that obvious bug.
(As a side note: although the original commit was completely wrong,
it's still working for most of machines, as it sets to 32bit DMA mask
in the end. So the bug severity is low.)
Fixes: 15c75b09f8 ("ALSA: ctxfi: Fallback DMA mask to 32bit")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c520ff3d03 upstream.
When snd_seq_pool_done() is called, it marks the closing flag to
refuse the further cell insertions. But snd_seq_pool_done() itself
doesn't clear the cells but just waits until all cells are cleared by
the caller side. That is, it's racy, and this leads to the endless
stall as syzkaller spotted.
This patch addresses the racy by splitting the setup of pool->closing
flag out of snd_seq_pool_done(), and calling it properly before
snd_seq_pool_done().
BugLink: http://lkml.kernel.org/r/CACT4Y+aqqy8bZA1fFieifNxR2fAfFQQABcBHj801+u5ePV0URw@mail.gmail.com
Reported-and-tested-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 92461f5d72 upstream.
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory that lie beyond the end of the endpoint
array should a malicious device lack the expected endpoints.
Fixes: bdb5c57f20 ("Input: add sur40 driver for Samsung SUR40... ")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cb1b494663 upstream.
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ac2ee9ba95 upstream.
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.
Fixes: c04148f915 ("Input: add driver for USB VoIP phones with CM109...")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5cc4a1a9f5 upstream.
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.
Fixes: aca951a22a ("[PATCH] input-driver-yealink-P1K-usb-phone")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ba340d7b83 upstream.
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.
Fixes: bba5394ad3 ("Input: add support for Hanwang tablets")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1916d31927 upstream.
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack control-interface endpoints.
Fixes: 628329d524 ("Input: add IMS Passenger Control Unit driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 59cf8bed44 upstream.
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory that lie beyond the end of the endpoint
array should a malicious device lack the expected endpoints.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 92ef6f97a6 upstream.
EeeBook X205TA is yet another ASUS device with a special touchpad
firmware that needs to be accounted for during initialization, or
else the touchpad will go into an invalid state upon suspend/resume.
Adding the appropriate ic_type and product_id check fixes the problem.
Signed-off-by: Matjaz Hegedic <matjaz.hegedic@gmail.com>
Acked-by: KT Liao <kt.liao@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a687c5765b upstream.
When a user connects a DS4 twice using USB and BT, we reject the
second device connection after the setup work. We then perform
a cleanup, but during cleanup we are not removing the touchpad
device. This leads to leakage of an input device, which we would
never remove. It can likely result into a kernel oops as well
when the touchpad evdev node is accessed and the underlaying HID
device has been removed from the system.
[jkosina@suse.cz: added stable annotation]
Fixes: ac797b95f5 ("HID: sony: Make the DS4 touchpad a separate device")
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 39e6c8208d upstream.
While playing with mlx4 hardware timestamping of RX packets, I found
that some packets were received by TCP stack with a ~200 ms delay...
Since the timestamp was provided by the NIC, and my probe was added
in tcp_v4_rcv() while in BH handler, I was confident it was not
a sender issue, or a drop in the network.
This would happen with a very low probability, but hurting RPC
workloads.
A NAPI driver normally arms the IRQ after the napi_complete_done(),
after NAPI_STATE_SCHED is cleared, so that the hard irq handler can grab
it.
Problem is that if another point in the stack grabs NAPI_STATE_SCHED bit
while IRQ are not disabled, we might have later an IRQ firing and
finding this bit set, right before napi_complete_done() clears it.
This can happen with busy polling users, or if gro_flush_timeout is
used. But some other uses of napi_schedule() in drivers can cause this
as well.
thread 1 thread 2 (could be on same cpu, or not)
// busy polling or napi_watchdog()
napi_schedule();
...
napi->poll()
device polling:
read 2 packets from ring buffer
Additional 3rd packet is
available.
device hard irq
// does nothing because
NAPI_STATE_SCHED bit is owned by thread 1
napi_schedule();
napi_complete_done(napi, 2);
rearm_irq();
Note that rearm_irq() will not force the device to send an additional
IRQ for the packet it already signaled (3rd packet in my example)
This patch adds a new NAPI_STATE_MISSED bit, that napi_schedule_prep()
can set if it could not grab NAPI_STATE_SCHED
Then napi_complete_done() properly reschedules the napi to make sure
we do not miss something.
Since we manipulate multiple bits at once, use cmpxchg() like in
sk_busy_loop() to provide proper transactions.
In v2, I changed napi_watchdog() to use a relaxed variant of
napi_schedule_prep() : No need to set NAPI_STATE_MISSED from this point.
In v3, I added more details in the changelog and clears
NAPI_STATE_MISSED in busy_poll_stop()
In v4, I added the ideas given by Alexander Duyck in v3 review
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f43feef4e6 ]
The ECC bit positions that describe whether the ECC interrupt is for
Tx, Rx or descriptor memory and whether the it is a single correctable
or double detected error were defined in incorrectly (reversed order).
Fix the bit position definitions for these settings so that the proper
ECC handling is performed.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 15bb7745e9 ]
icsk_ack.lrcvtime has a 0 value at socket creation time.
tcpi_last_data_recv can have bogus value if no payload is ever received.
This patch initializes icsk_ack.lrcvtime for active sessions
in tcp_finish_connect(), and for passive sessions in
tcp_create_openreq_child()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1d2a6a5e4b ]
Commit 2ae0f17df1 ("genetlink: use idr to track families") replaced
if (++n < fams_to_skip)
continue;
into:
if (n++ < fams_to_skip)
continue;
This subtle change cause that on retry ctrl_dumpfamily() call we omit
one family that failed to do ctrl_fill_info() on previous call, because
cb->args[0] = n number counts also family that failed to do
ctrl_fill_info().
Patch fixes the problem and avoid confusion in the future just decrease
n counter when ctrl_fill_info() fail.
User visible problem caused by this bug is failure to get access to
some genetlink family i.e. nl80211. However problem is reproducible
only if number of registered genetlink families is big enough to
cause second call of ctrl_dumpfamily().
Cc: Xose Vazquez Perez <xose.vazquez@gmail.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Johannes Berg <johannes@sipsolutions.net>
Fixes: 2ae0f17df1 ("genetlink: use idr to track families")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a97e50cc4c ]
In sk_clone_lock(), we create a new socket and inherit most of the
parent's members via sock_copy() which memcpy()'s various sections.
Now, in case the parent socket had a BPF socket filter attached,
then newsk->sk_filter points to the same instance as the original
sk->sk_filter.
sk_filter_charge() is then called on the newsk->sk_filter to take a
reference and should that fail due to hitting max optmem, we bail
out and release the newsk instance.
The issue is that commit 278571baca ("net: filter: simplify socket
charging") wrongly combined the dismantle path with the failure path
of xfrm_sk_clone_policy(). This means, even when charging failed, we
call sk_free_unlock_clone() on the newsk, which then still points to
the same sk_filter as the original sk.
Thus, sk_free_unlock_clone() calls into __sk_destruct() eventually
where it tests for present sk_filter and calls sk_filter_uncharge()
on it, which potentially lets sk_omem_alloc wrap around and releases
the eBPF prog and sk_filter structure from the (still intact) parent.
Fix it by making sure that when sk_filter_charge() failed, we reset
newsk->sk_filter back to NULL before passing to sk_free_unlock_clone(),
so that we don't mess with the parents sk_filter.
Only if xfrm_sk_clone_policy() fails, we did reach the point where
either the parent's filter was NULL and as a result newsk's as well
or where we previously had a successful sk_filter_charge(), thus for
that case, we do need sk_filter_uncharge() to release the prior taken
reference on sk_filter.
Fixes: 278571baca ("net: filter: simplify socket charging")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c64c0b3cac ]
Alexander reported a KMSAN splat caused by reads of uninitialized
field (tb_id_in) from user provided struct fib_result_nl
It turns out nl_fib_input() sanity tests on user input is a bit
wrong :
User can pretend nlh->nlmsg_len is big enough, but provide
at sendmsg() time a too small buffer.
Reported-by: Alexander Potapenko <glider@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 31739eae73 ]
Commit 6ac3ce8295 ("net: bcmgenet: Remove excessive PHY reset")
removed the bcmgenet_mii_reset() function from bcmgenet_power_up() and
bcmgenet_internal_phy_setup() functions. In so doing it broke the reset
of the internal PHY devices used by the GENETv1-GENETv3 which required
this reset before the UniMAC was enabled. It also broke the internal
GPHY devices used by the GENETv4 because the config_init that installed
the AFE workaround was no longer occurring after the reset of the GPHY
performed by bcmgenet_phy_power_set() in bcmgenet_internal_phy_setup().
In addition the code in bcmgenet_internal_phy_setup() related to the
"enable APD" comment goes with the bcmgenet_mii_reset() so it should
have also been removed.
Commit bd4060a610 ("net: bcmgenet: Power on integrated GPHY in
bcmgenet_power_up()") moved the bcmgenet_phy_power_set() call to the
bcmgenet_power_up() function, but failed to remove it from the
bcmgenet_internal_phy_setup() function. Had it done so, the
bcmgenet_internal_phy_setup() function would have been empty and could
have been removed at that time.
Commit 5dbebbb44a ("net: bcmgenet: Software reset EPHY after power on")
was submitted to correct the functional problems introduced by
commit 6ac3ce8295 ("net: bcmgenet: Remove excessive PHY reset"). It
was included in v4.4 and made available on 4.3-stable. Unfortunately,
it didn't fully revert the commit because this bcmgenet_mii_reset()
doesn't apply the soft reset to the internal GPHY used by GENETv4 like
the previous one did. This prevents the restoration of the AFE work-
arounds for internal GPHY devices after the bcmgenet_phy_power_set() in
bcmgenet_internal_phy_setup().
This commit takes the alternate approach of removing the unnecessary
bcmgenet_internal_phy_setup() function which shouldn't have been in v4.3
so that when bcmgenet_mii_reset() was restored it should have only gone
into bcmgenet_power_up(). This will avoid the problems while also
removing the redundancy (and hopefully some of the confusion).
Fixes: 6ac3ce8295 ("net: bcmgenet: Remove excessive PHY reset")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d515684d78 ]
In the case udp_sk(sk)->pending is AF_INET6, udpv6_sendmsg() would
jump to do_append_data, skipping the initialization of sockc.tsflags.
Fix the problem by moving sockc.tsflags initialization earlier.
The bug was detected with KMSAN.
Fixes: c14ac9451c ("sock: enable timestamping using control messages")
Signed-off-by: Alexander Potapenko <glider@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8ab7e2ae15 ]
RX packets statistics ('rx_packets' counter) used to count LRO packets
as one, even though it contains multiple segments.
This patch will increment the counter by the number of segments, and
align the driver with the behavior of other drivers in the stack.
Note that no information is lost in this patch due to 'rx_lro_packets'
counter existence.
Before, ethtool showed:
$ ethtool -S ens6 | egrep "rx_packets|rx_lro_packets"
rx_packets: 435277
rx_lro_packets: 35847
rx_packets_phy: 1935066
Now, we will see the more logical statistics:
$ ethtool -S ens6 | egrep "rx_packets|rx_lro_packets"
rx_packets: 1935066
rx_lro_packets: 35847
rx_packets_phy: 1935066
Fixes: e586b3b0ba ("net/mlx5: Ethernet Datapath files")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d3a4e4da54 ]
TX packets statistics ('tx_packets' counter) used to count GSO packets
as one, even though it contains multiple segments.
This patch will increment the counter by the number of segments, and
align the driver with the behavior of other drivers in the stack.
Note that no information is lost in this patch due to 'tx_tso_packets'
counter existence.
Before, ethtool showed:
$ ethtool -S ens6 | egrep "tx_packets|tx_tso_packets"
tx_packets: 61340
tx_tso_packets: 60954
tx_packets_phy: 2451115
Now, we will see the more logical statistics:
$ ethtool -S ens6 | egrep "tx_packets|tx_tso_packets"
tx_packets: 2451115
tx_tso_packets: 60954
tx_packets_phy: 2451115
Fixes: e586b3b0ba ("net/mlx5: Ethernet Datapath files")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5f40b4ed97 ]
With ConnectX-4 sharing SRQs from the same space as QPs, we hit a
limit preventing some applications to allocate needed QPs amount.
Double the size to 256K.
Fixes: e126ba97db ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1ad9a00ae0 ]
This was added to allow the TC offloading code to identify offloading
encap/decap vxlan rules.
The VF reps are effectively related to the same mlx5 PCI device as the
PF. Since the kernel invokes the (say) delete ndo for each netdev, the
FW erred on multiple vxlan dst port deletes when the port was deleted
from the system.
We fix that by keeping the registration to be carried out only by the
PF. Since the PF serves as the uplink device, the VF reps will look
up a port there and realize if they are ok to offload that.
Tested:
<SETUP VFS>
<SETUP switchdev mode to have representors>
ip link add vxlan1 type vxlan id 44 dev ens5f0 dstport 9999
ip link set vxlan1 up
ip link del dev vxlan1
Fixes: 4a25730eb2 ('net/mlx5e: Add ndo_udp_tunnel_add to VF representors')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 375f51e2b5 ]
Changing the eswitch inline mode can potentially cause already configured
flows not to match the policy. E.g. set policy L4, add some L4 rules,
set policy to L2 --> bad! Hence we disallow it.
Keep track of how many offloaded rules are now set and refuse
inline mode changes if this isn't zero.
Fixes: bffaa91658 ("net/mlx5: E-Switch, Add control for inline mode")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d85cdccbb3 ]
Refactor the code to deal with add/del TC rules to have handler per NIC/E-switch
offloading use case, and push the latter into the e-switch code. This provides
better separation and is to be used in down-stream patch for applying a fix.
Fixes: bffaa91658 ("net/mlx5: E-Switch, Add control for inline mode")
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1f30a86c58 ]
The switch cases for the rate limit set and query commands were
missing, which could get us wrong under fw error or driver reset
flow, fix that.
Fixes: 1466cc5b23 ('net/mlx5: Rate limit tables support')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3dc857f0e8 ]
The VRF driver takes a reference to the inet6_dev on the VRF device for
its rt6_local dst when handling local traffic through the VRF device as
a loopback. When the device is deleted the driver does a put on the idev
but does not reset rt6i_idev in the rt6_info struct. When the dst is
destroyed, dst_destroy calls ip6_dst_destroy which does a second put for
what is essentially the same reference causing it to be prematurely freed.
Reset rt6i_idev after the put in the vrf driver.
Fixes: b4869aa2f8 ("net: vrf: ipv6 support for local traffic to
local addresses")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6bd845d1cf ]
This is a Dell branded Sierra Wireless EM7455. It is operating in
MBIM mode by default, but can be configured to provide two QMI/RMNET
functions.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7df9c24625 ]
Dmitry has reported that a BUG_ON() condition in unix_notinflight()
may be triggered by a simple code that forwards unix socket in an
SCM_RIGHTS message.
That is caused by incorrect unix socket GC implementation in unix_gc().
The GC first collects list of candidates, then (a) decrements their
"children's" inflight counter, (b) checks which inflight counters are
now 0, and then (c) increments all inflight counters back.
(a) and (c) are done by calling scan_children() with inc_inflight or
dec_inflight as the second argument.
Commit 6209344f5a ("net: unix: fix inflight counting bug in garbage
collector") changed scan_children() such that it no longer considers
sockets that do not have UNIX_GC_CANDIDATE flag. It also added a block
of code that that unsets this flag _before_ invoking
scan_children(, dec_iflight, ). This may lead to incorrect inflight
counters for some sockets.
This change fixes this bug by changing order of operations:
UNIX_GC_CANDIDATE is now unset only after all inflight counters are
restored to the original state.
kernel BUG at net/unix/garbage.c:149!
RIP: 0010:[<ffffffff8717ebf4>] [<ffffffff8717ebf4>]
unix_notinflight+0x3b4/0x490 net/unix/garbage.c:149
Call Trace:
[<ffffffff8716cfbf>] unix_detach_fds.isra.19+0xff/0x170 net/unix/af_unix.c:1487
[<ffffffff8716f6a9>] unix_destruct_scm+0xf9/0x210 net/unix/af_unix.c:1496
[<ffffffff86a90a01>] skb_release_head_state+0x101/0x200 net/core/skbuff.c:655
[<ffffffff86a9808a>] skb_release_all+0x1a/0x60 net/core/skbuff.c:668
[<ffffffff86a980ea>] __kfree_skb+0x1a/0x30 net/core/skbuff.c:684
[<ffffffff86a98284>] kfree_skb+0x184/0x570 net/core/skbuff.c:705
[<ffffffff871789d5>] unix_release_sock+0x5b5/0xbd0 net/unix/af_unix.c:559
[<ffffffff87179039>] unix_release+0x49/0x90 net/unix/af_unix.c:836
[<ffffffff86a694b2>] sock_release+0x92/0x1f0 net/socket.c:570
[<ffffffff86a6962b>] sock_close+0x1b/0x20 net/socket.c:1017
[<ffffffff81a76b8e>] __fput+0x34e/0x910 fs/file_table.c:208
[<ffffffff81a771da>] ____fput+0x1a/0x20 fs/file_table.c:244
[<ffffffff81483ab0>] task_work_run+0x1a0/0x280 kernel/task_work.c:116
[< inline >] exit_task_work include/linux/task_work.h:21
[<ffffffff8141287a>] do_exit+0x183a/0x2640 kernel/exit.c:828
[<ffffffff8141383e>] do_group_exit+0x14e/0x420 kernel/exit.c:931
[<ffffffff814429d3>] get_signal+0x663/0x1880 kernel/signal.c:2307
[<ffffffff81239b45>] do_signal+0xc5/0x2190 arch/x86/kernel/signal.c:807
[<ffffffff8100666a>] exit_to_usermode_loop+0x1ea/0x2d0
arch/x86/entry/common.c:156
[< inline >] prepare_exit_to_usermode arch/x86/entry/common.c:190
[<ffffffff81009693>] syscall_return_slowpath+0x4d3/0x570
arch/x86/entry/common.c:259
[<ffffffff881478e6>] entry_SYSCALL_64_fastpath+0xc4/0xc6
Link: https://lkml.org/lkml/2017/3/6/252
Signed-off-by: Andrey Ulanov <andreyu@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Fixes: 6209344 ("net: unix: fix inflight counting bug in garbage collector")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8f3dbfd79e ]
Added a case for OVS_TUNNEL_KEY_ATTR_PAD to the switch statement
in ip_tun_from_nlattr in order to prevent the default case
returning an error.
Fixes: b46f6ded90 ("libnl: nla_put_be64(): align on a 64-bit area")
Signed-off-by: Kris Murphy <kriskend@linux.vnet.ibm.com>
Acked-by: Joe Stringer <joe@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 622c36f143 ]
Newer hardware does not provide a cumulative payload length when multiple
descriptors are needed to handle the data. Once the MTU increases beyond
the size that can be handled by a single descriptor, the SKB does not get
built properly by the driver.
The driver will now calculate the size of the data buffers used by the
hardware. The first buffer of the first descriptor is for packet headers
or packet headers and data when the headers can't be split. Subsequent
descriptors in a multi-descriptor chain will not use the first buffer. The
second buffer is used by all the descriptors in the chain for payload data.
Based on whether the driver is processing the first, intermediate, or last
descriptor it can calculate the buffer usage and build the SKB properly.
Tested and verified on both old and new hardware.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 22a0e18eac ]
I mistakenly added the code to release sk->sk_frag in
sk_common_release() instead of sk_destruct()
TCP sockets using sk->sk_allocation == GFP_ATOMIC do no call
sk_common_release() at close time, thus leaking one (order-3) page.
iSCSI is using such sockets.
Fixes: 5640f76858 ("net: use a per task frag allocator")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5371bbf4b2 ]
Suspending the PHY would be putting it in a low power state where it
may no longer allow us to do Wake-on-LAN.
Fixes: cc013fb488 ("net: bcmgenet: correctly suspend and resume PHY device")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3d20f1f7bd ]
When dealing with ipv6 source tunnel key address attribute
(OVS_TUNNEL_KEY_ATTR_IPV6_SRC) we are wrongly setting the tunnel
dst ip, fix that.
Fixes: 6b26ba3a7d ('openvswitch: netlink attributes for IPv6 tunneling')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Paul Blakey <paulb@mellanox.com>
Acked-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Joe Stringer <joe@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d18c2747f upstream.
pids_can_fork() is special in that the css association is guaranteed
to be stable throughout the function and thus doesn't need RCU
protection around task_css access. When determining the css to charge
the pid, task_css_check() is used to override the RCU sanity check.
While adding a warning message on fork rejection from pids limit,
135b8b37bd ("cgroup: Add pids controller event when fork fails
because of pid limit") incorrectly added a task_css access which is
neither RCU protected or explicitly annotated. This triggers the
following suspicious RCU usage warning when RCU debugging is enabled.
cgroup: fork rejected by pids controller in
===============================
[ ERR: suspicious RCU usage. ]
4.10.0-work+ #1 Not tainted
-------------------------------
./include/linux/cgroup.h:435 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 0
1 lock held by bash/1748:
#0: (&cgroup_threadgroup_rwsem){+++++.}, at: [<ffffffff81052c96>] _do_fork+0xe6/0x6e0
stack backtrace:
CPU: 3 PID: 1748 Comm: bash Not tainted 4.10.0-work+ #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.9.3-1.fc25 04/01/2014
Call Trace:
dump_stack+0x68/0x93
lockdep_rcu_suspicious+0xd7/0x110
pids_can_fork+0x1c7/0x1d0
cgroup_can_fork+0x67/0xc0
copy_process.part.58+0x1709/0x1e90
_do_fork+0xe6/0x6e0
SyS_clone+0x19/0x20
do_syscall_64+0x5c/0x140
entry_SYSCALL64_slow_path+0x25/0x25
RIP: 0033:0x7f7853fab93a
RSP: 002b:00007ffc12d05c90 EFLAGS: 00000246 ORIG_RAX: 0000000000000038
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f7853fab93a
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000001200011
RBP: 00007ffc12d05cc0 R08: 0000000000000000 R09: 00007f78548db700
R10: 00007f78548db9d0 R11: 0000000000000246 R12: 00000000000006d4
R13: 0000000000000001 R14: 0000000000000000 R15: 000055e3ebe2c04d
/asdf
There's no reason to dereference task_css again here when the
associated css is already available. Fix it by replacing the
task_cgroup() call with css->cgroup.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Mike Galbraith <efault@gmx.de>
Fixes: 135b8b37bd ("cgroup: Add pids controller event when fork fails because of pid limit")
Cc: Kenny Yu <kennyyu@fb.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 320661b08d upstream.
Update to pcpu_nr_empty_pop_pages in pcpu_alloc() is currently done
without holding pcpu_lock. This can lead to bad updates to the variable.
Add missing lock calls.
Fixes: b539b87fed ("percpu: implmeent pcpu_nr_empty_pop_pages and chunk->nr_populated")
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 28ea06c46f upstream.
Commit 88ffbf3e03 switches to using rhashtables for glocks, hashing over
the entire struct lm_lockname instead of its individual fields. On some
architectures, struct lm_lockname contains a hole of uninitialized
memory due to alignment rules, which now leads to incorrect hash values.
Get rid of that hole.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 68c32f9c2a upstream.
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.
Fixes: cf7776dc05 ("[PATCH] isdn4linux: Siemens Gigaset drivers - direct USB connection")
Cc: Hansjoerg Lipp <hjlipp@web.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 13603685c1 upstream.
As reported by Max, the Windows 2008 R2 chkdsk utility expects
VERIFY_16 to be supported, and does not handle the returned
CHECK_CONDITION properly, resulting in an infinite loop.
The kernel will log huge amounts of this error:
kernel: TARGET_CORE[iSCSI]: Unsupported SCSI Opcode 0x8f, sending
CHECK_CONDITION.
Signed-off-by: Max Lohrmann <post@wickenrode.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8893cf6cb1 upstream.
Commit 669f044170 ("scsi: srp_transport: Move queuecommand() wait code
to SCSI core") can make scsi_internal_device_block() sleep. However,
the mpt3sas driver can call this function from an interrupt
handler. Hence add a second argument to scsi_internal_device_block()
that restores the old behavior of this function for the mpt3sas handler.
The call chain that triggered an "IRQ handler enabled interrupts"
complaint is as follows:
_base_interrupt()
-> _base_async_event()
-> mpt3sas_scsih_event_callback()
-> _scsih_check_topo_delete_events()
-> _scsih_block_io_to_children_attached_directly()
-> _scsih_block_io_device()
-> _scsih_internal_device_block()
-> scsi_internal_device_block()
Reported-by: Omar Sandoval <osandov@osandov.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Omar Sandoval <osandov@osandov.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Chaitra P B <chaitra.basappa@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Cc: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Tested-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f8830f5bb upstream.
There's a rather long standing regression from the commit "libiscsi:
Reduce locking contention in fast path"
Depending on iSCSI target behavior, it's possible to hit the case in
iscsi_complete_task where the task is still on a pending list
(!list_empty(&task->running)). When that happens the task is removed
from the list while holding the session back_lock, but other task list
modification occur under the frwd_lock. That leads to linked list
corruption and eventually a panicked system.
Rather than back out the session lock split entirely, in order to try
and keep some of the performance gains this patch adds another lock to
maintain the task lists integrity.
Major enterprise supported kernels have been backing out the lock split
for while now, thanks to the efforts at IBM where a lab setup has the
most reliable reproducer I've seen on this issue. This patch has been
tested there successfully.
Signed-off-by: Chris Leech <cleech@redhat.com>
Fixes: 659743b02c ("[SCSI] libiscsi: Reduce locking contention in fast path")
Reported-by: Prashantha Subbarao <psubbara@us.ibm.com>
Reviewed-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a04e54f2c3 upstream.
The following fixes a divide by zero OOPs with TYPE_TAPE
due to pscsi_tape_read_blocksize() failing causing a zero
sd->sector_size being propigated up via dev_attrib.hw_block_size.
It also fixes another long-standing bug where TYPE_TAPE and
TYPE_MEDIMUM_CHANGER where using pscsi_create_type_other(),
which does not call scsi_device_get() to take the device
reference. Instead, rename pscsi_create_type_rom() to
pscsi_create_type_nondisk() and use it for all cases.
Finally, also drop a dump_stack() in pscsi_get_blocks() for
non TYPE_DISK, which in modern target-core can get invoked
via target_sense_desc_format() during CHECK_CONDITION.
Reported-by: Malcolm Haak <insanemal@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61eb2b43b9 upstream.
Neil Brown pointed out a potential deadlock in raid 10 code with
bio_split/chain. The raid1 code could have the same issue, but recent
barrier rework makes it less likely to happen. The deadlock happens in
below sequence:
1. generic_make_request(bio), this will set current->bio_list
2. raid10_make_request will split bio to bio1 and bio2
3. __make_request(bio1), wait_barrer, add underlayer disk bio to
current->bio_list
4. __make_request(bio2), wait_barrer
If raise_barrier happens between 3 & 4, since wait_barrier runs at 3,
raise_barrier waits for IO completion from 3. And since raise_barrier
sets barrier, 4 waits for raise_barrier. But IO from 3 can't be
dispatched because raid10_make_request() doesn't finished yet.
The solution is to adjust the IO ordering. Quotes from Neil:
"
It is much safer to:
if (need to split) {
split = bio_split(bio, ...)
bio_chain(...)
make_request_fn(split);
generic_make_request(bio);
} else
make_request_fn(mddev, bio);
This way we first process the initial section of the bio (in 'split')
which will queue some requests to the underlying devices. These
requests will be queued in generic_make_request.
Then we queue the remainder of the bio, which will be added to the end
of the generic_make_request queue.
Then we return.
generic_make_request() will pop the lower-level device requests off the
queue and handle them first. Then it will process the remainder
of the original bio once the first section has been fully processed.
"
Note, this only happens in read path. In write path, the bio is flushed to
underlaying disks either by blk flush (from schedule) or offladed to raid1/10d.
It's queued in current->bio_list.
Cc: Coly Li <colyli@suse.de>
Suggested-by: NeilBrown <neilb@suse.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b985735be7 upstream.
The INTMASK_REG register does not exist on EIP76. Due to this, the call:
omap_rng_write(priv, RNG_INTMASK_REG, RNG_SHUTDOWN_OFLO_MASK);
ends up, through the reg_map_eip76[] array, in accessing the register at
offset 0, which is the RNG_OUTPUT_0_REG. This by itself doesn't cause
any problem, but clearly doesn't enable the interrupt as it was
expected.
On EIP76, the register that allows to enable the interrupt is
RNG_CONTROL_REG. And just like RNG_INTMASK_REG, it's bit 1 of this
register that allows to enable the shutdown_oflo interrupt.
Fixes: 383212425c ("hwrng: omap - Add device variant for SafeXcel IP-76 found in Armada 8K")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 761c251028 upstream.
The omap-rng driver currently uses of_clk_get() to get a reference to
the clock, but never releases that reference. This commit fixes that by
using devm_clk_get() instead.
Fixes: 383212425c ("hwrng: omap - Add device variant for SafeXcel IP-76 found in Armada 8K")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45c2fdde01 upstream.
Commit 383212425c ("hwrng: omap - Add device variant for SafeXcel
IP-76 found in Armada 8K") added support for the SafeXcel IP-76 variant
of the IP. This modification included getting a reference and enabling a
clock. Unfortunately, this was done *after* writing to the
RNG_INTMASK_REG register. This generally works fine when the driver is
built-in because the clock might have been left enabled by the
bootloader, but fails short when the driver is built as a module: it
causes a system hang because a register is being accessed while the
clock is not enabled.
This commit fixes that by making the register access *after* enabling
the clock.
This issue was found by the kernelci.org testing effort.
Fixes: 383212425c ("hwrng: omap - Add device variant for SafeXcel IP-76 found in Armada 8K")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 97ee351b50 upstream.
Recent toolchains force the TOC to be 256 byte aligned. We need to
enforce this alignment in the zImage linker script, otherwise pointers
to our TOC variables (__toc_start) could be incorrect. If the actual
start of the TOC and __toc_start don't have the same value we crash
early in the zImage wrapper.
Suggested-by: Alan Modra <amodra@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 63513232f8 upstream.
Since rpc_task is async, the release function should be called which
will free the impl_id, scope, and owner.
Trond pointed at 2 more problems:
-- use of client pointer after free in the nfs4_exchangeid_release() function
-- cl_count mismatch if rpc_run_task() isn't run
Fixes: 8d89bd70bc ("NFS setup async exchange_id")
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eed50879d6 upstream.
New complaint from kbuild for 4.9.y:
net/sunrpc/xprtrdma/verbs.c:489:19: sparse: incompatible types in
comparison expression (different type sizes)
verbs.c:
489 max_sge = min(ia->ri_device->attrs.max_sge, RPCRDMA_MAX_SEND_SGES);
I can't reproduce this running sparse here. Likewise, "make W=1
net/sunrpc/xprtrdma/verbs.o" never indicated any issue.
A little poking suggests that because the range of its values is
small, gcc can make the actual width of RPCRDMA_MAX_SEND_SGES
smaller than the width of an unsigned integer.
Fixes: 16f906d66c ("xprtrdma: Reduce required number of send SGEs")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0977762f6d upstream.
Before this patch, device InJournal will be included in prexor
(SYNDROME_SRC_WANT_DRAIN) but not in reconstruct (SYNDROME_SRC_WRITTEN). So it
will break parity calculation. With srctype == SYNDROME_SRC_WRITTEN, we need
include both dev with non-null ->written and dev with R5_InJournal. This fixes
logic in 1e6d690(md/r5cache: caching phase of r5cache)
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 73580dac76 upstream.
On those parisc machines which don't provide a software power off
function, the system currently kills the init process at the end of a
shutdown and unexpectedly restarts insteads of halting.
Fix it by adding a loop which will not return.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5f655322b1 upstream.
The parisc kernel doesn't work with CONFIG_MODVERSIONS since the commit
71810db27c. It can't load modules with the
error: "module unix: Unknown relocation: 41".
The commit changes __kcrctab from 64-bit valus to 32-bit values. The
assembler generates R_PARISC_SECREL32 secrel relocation for them and the
module loader doesn't support this relocation.
This patch adds the R_PARISC_SECREL32 relocation to the module loader.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 316ec0624f upstream.
The previously submitted patch did not resolve the random segmentation
faults observed on the phantom buildd system. There are still
unresolved problems with the Debian 4.8 and 4.9 kernels on C8000.
The attached patch removes the flush of the offset map pages and does a
whole data cache flush for large ranges. No other arch flushes the
offset map in these routines as far as I can tell.
I have not observed any random segmentation faults on rp3440 in two
weeks of testing with 4.10.0 and 4.10.1.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b666809e1 upstream.
When FW notify driver or driver detects low FW resource,
driver tries to send out Busy SCSI Status to tell Initiator
side to back off. During the send process, the lock was not held.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 474c90156c upstream.
gcc-7 has an "optimization" pass that completely screws up, and
generates the code expansion for the (impossible) case of calling
ilog2() with a zero constant, even when the code gcc compiles does not
actually have a zero constant.
And we try to generate a compile-time error for anybody doing ilog2() on
a constant where that doesn't make sense (be it zero or negative). So
now gcc7 will fail the build due to our sanity checking, because it
created that constant-zero case that didn't actually exist in the source
code.
There's a whole long discussion on the kernel mailing about how to work
around this gcc bug. The gcc people themselevs have discussed their
"feature" in
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=72785
but it's all water under the bridge, because while it looked at one
point like it would be solved by the time gcc7 was released, that was
not to be.
So now we have to deal with this compiler braindamage.
And the only simple approach seems to be to just delete the code that
tries to warn about bad uses of ilog2().
So now "ilog2()" will just return 0 not just for the value 1, but for
any non-positive value too.
It's not like I can recall anybody having ever actually tried to use
this function on any invalid value, but maybe the sanity check just
meant that such code never made it out in public.
Reported-by: Laura Abbott <labbott@redhat.com>
Cc: John Stultz <john.stultz@linaro.org>,
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 28b62b1458 upstream.
Running TCRYPT with LRW compiled causes spinlock recursion:
testing speed of async lrw(aes) (lrw(ecb-aes-s5p)) encryption
tcrypt: test 0 (256 bit key, 16 byte blocks): 19007 operations in 1 seconds (304112 bytes)
tcrypt: test 1 (256 bit key, 64 byte blocks): 15753 operations in 1 seconds (1008192 bytes)
tcrypt: test 2 (256 bit key, 256 byte blocks): 14293 operations in 1 seconds (3659008 bytes)
tcrypt: test 3 (256 bit key, 1024 byte blocks): 11906 operations in 1 seconds (12191744 bytes)
tcrypt: test 4 (256 bit key, 8192 byte blocks):
BUG: spinlock recursion on CPU#1, irq/84-10830000/89
lock: 0xeea99a68, .magic: dead4ead, .owner: irq/84-10830000/89, .owner_cpu: 1
CPU: 1 PID: 89 Comm: irq/84-10830000 Not tainted 4.11.0-rc1-00001-g897ca6d0800d #559
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[<c010e1ec>] (unwind_backtrace) from [<c010ae1c>] (show_stack+0x10/0x14)
[<c010ae1c>] (show_stack) from [<c03449c0>] (dump_stack+0x78/0x8c)
[<c03449c0>] (dump_stack) from [<c015de68>] (do_raw_spin_lock+0x11c/0x120)
[<c015de68>] (do_raw_spin_lock) from [<c0720110>] (_raw_spin_lock_irqsave+0x20/0x28)
[<c0720110>] (_raw_spin_lock_irqsave) from [<c0572ca0>] (s5p_aes_crypt+0x2c/0xb4)
[<c0572ca0>] (s5p_aes_crypt) from [<bf1d8aa4>] (do_encrypt+0x78/0xb0 [lrw])
[<bf1d8aa4>] (do_encrypt [lrw]) from [<bf1d8b00>] (encrypt_done+0x24/0x54 [lrw])
[<bf1d8b00>] (encrypt_done [lrw]) from [<c05732a0>] (s5p_aes_complete+0x60/0xcc)
[<c05732a0>] (s5p_aes_complete) from [<c0573440>] (s5p_aes_interrupt+0x134/0x1a0)
[<c0573440>] (s5p_aes_interrupt) from [<c01667c4>] (irq_thread_fn+0x1c/0x54)
[<c01667c4>] (irq_thread_fn) from [<c0166a98>] (irq_thread+0x12c/0x1e0)
[<c0166a98>] (irq_thread) from [<c0136a28>] (kthread+0x108/0x138)
[<c0136a28>] (kthread) from [<c0107778>] (ret_from_fork+0x14/0x3c)
Interrupt handling routine was calling req->base.complete() under
spinlock. In most cases this wasn't fatal but when combined with some
of the cipher modes (like LRW) this caused recursion - starting the new
encryption (s5p_aes_crypt()) while still holding the spinlock from
previous round (s5p_aes_complete()).
Beside that, the s5p_aes_interrupt() error handling path could execute
two completions in case of error for RX and TX blocks.
Rewrite the interrupt handling routine and the completion by:
1. Splitting the operations on scatterlist copies from
s5p_aes_complete() into separate s5p_sg_done(). This still should be
done under lock.
The s5p_aes_complete() now only calls req->base.complete() and it has
to be called outside of lock.
2. Moving the s5p_aes_complete() out of spinlock critical sections.
In interrupt service routine s5p_aes_interrupts(), it appeared in few
places, including error paths inside other functions called from ISR.
This code was not so obvious to read so simplify it by putting the
s5p_aes_complete() only within ISR level.
Reported-by: Nathan Royce <nroycea+kernel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aa2be9b3d6 upstream.
Turning on crypto self-tests on a POWER8 shows:
alg: hash: Test 1 failed for crc32c-vpmsum
00000000: ff ff ff ff
Comparing the code with the Intel CRC32c implementation on which
ours is based shows that we are doing an init with 0, not ~0
as CRC32c requires.
This probably wasn't caught because btrfs does its own weird
open-coded initialisation.
Initialise our internal context to ~0 on init.
This makes the self-tests pass, and btrfs continues to work.
Fixes: 6dd7a82cc5 ("crypto: powerpc - Add POWER8 optimised crc32c")
Cc: Anton Blanchard <anton@samba.org>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Acked-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 49ec8f5b6a upstream.
The rdtgroup_kn_unlock waits for the last user to release and put its
node. But it's calling kernfs_put on the node which calls the
rdtgroup_kn_unlock, which might not be the group's directory node, but
another group's file node.
This race could be easily reproduced by running 2 instances
of following script:
mount -t resctrl resctrl /sys/fs/resctrl/
pushd /sys/fs/resctrl/
mkdir krava
echo "krava" > krava/schemata
rmdir krava
popd
umount /sys/fs/resctrl
It triggers the slub debug error message with following command
line config: slub_debug=,kernfs_node_cache.
Call kernfs_put on the group's node to fix it.
Fixes: 60cf5e101f ("x86/intel_rdt: Add mkdir to resctrl file system")
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Shaohua Li <shli@fb.com>
Link: http://lkml.kernel.org/r/1489501253-20248-1-git-send-email-jolsa@kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 44fee88cea upstream.
Subhransu reported that convert_art_to_tsc() isn't working for him.
The ART to TSC relation is only set up for systems which use the refined
TSC calibration. Systems with known TSC frequency (available via CPUID 15)
are not using the refined calibration and therefor the ART to TSC relation
is never established.
Add the setup to the known frequency init path which skips ART
calibration. The init code needs to be duplicated as for systems which use
refined calibration the ART setup must be delayed until calibration has
been done.
The problem has been there since the ART support was introdduced, but only
detected now because Subhransu tested the first time on hardware which has
TSC frequency enumerated via CPUID 15.
Note for stable: The conditional has changed from TSC_RELIABLE to
TSC_KNOWN_FREQUENCY.
[ tglx: Rewrote changelog and identified the proper 'Fixes' commit ]
Fixes: f9677e0f83 ("x86/tsc: Always Running Timer (ART) correlated clocksource")
Reported-by: "Prusty, Subhransu S" <subhransu.s.prusty@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: christopher.s.hall@intel.com
Cc: kevin.b.stanton@intel.com
Cc: john.stultz@linaro.org
Cc: akataria@vmware.com
Link: http://lkml.kernel.org/r/20170313145712.GI3312@twins.programming.kicks-ass.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 87a6b2975f upstream.
Pavel Machek reported the following warning on x86-32:
WARNING: kernel stack frame pointer at f50cdf98 in swapper/2:0 has bad value (null)
The warning is caused by the unwinder not realizing that it reached the
end of the stack, due to an unusual prologue which gcc sometimes
generates for aligned stacks. The prologue is based on a gcc feature
called the Dynamic Realign Argument Pointer (DRAP). It's almost always
enabled for aligned stacks when -maccumulate-outgoing-args isn't set.
This issue is similar to the one fixed by the following commit:
8023e0e2a4 ("x86/unwind: Adjust last frame check for aligned function stacks")
... but that fix was specific to x86-64.
Make the fix more generic to cover x86-32 as well, and also ensure that
the return address referred to by the frame pointer is a copy of the
original return address.
Fixes: acb4608ad1 ("x86/unwind: Create stack frames for saved syscall registers")
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: http://lkml.kernel.org/r/50d4924db716c264b14f1633037385ec80bf89d2.1489465609.git.jpoimboe@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 908764f6d0 upstream.
For LSPCON initialization during system resume we need AUX
functionality, but we call the corresponding encoder reset hook with all
interrupts disabled. Without interrupts we'll do a poll-wait for AUX
transfer completions, which adds a significant delay if the transfers
timeout/need to be retried for some reason.
Fix this by enabling interrupts before calling the reset hooks. Note
that while this will enable AUX interrupts it will keep HPD interrupts
disabled, in a similar way to the init time output setup code.
This issue existed since LSPCON support was added.
v2:
- Rebased on drm-tip.
Cc: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: David Weinehall <david.weinehall@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1480448429-27739-1-git-send-email-imre.deak@intel.com
(rebased onto v4.10.4 due to missing s/dev/dev_priv/ upstream change)
(corrected stable tag)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 90922a2d03 upstream.
On Qualcomm Datacenter Technologies QDF2400 SoCs, the ITS hardware
implementation uses 16Bytes for Interrupt Translation Entry (ITE),
but reports an incorrect value of 8Bytes in GITS_TYPER.ITTE_size.
It might cause kernel memory corruption depending on the number
of MSI(x) that are configured and the amount of memory that has
been allocated for ITEs in its_create_device().
This patch fixes the potential memory corruption by setting the
correct ITE size to 16Bytes.
Cc: stable@vger.kernel.org
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6892517629 upstream.
When invalidating guest TLBs, special care must be taken to
actually shoot the guest TLBs and not the host ones if we're
running on a VHE system. This is controlled by the HCR_EL2.TGE
bit, which we forget to clear before invalidating TLBs.
Address the issue by introducing two wrappers (__tlb_switch_to_guest
and __tlb_switch_to_host) that take care of both the VTTBR_EL2
and HCR_EL2.TGE switching.
Reported-by: Tomasz Nowicki <tnowicki@caviumnetworks.com>
Tested-by: Tomasz Nowicki <tnowicki@caviumnetworks.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 72ef9c4125 ]
This patch fixes a memory leak, which happens if the connection request
is not fulfilled between parsing the DCCP options and handling the SYN
(because e.g. the backlog is full), because we forgot to free the
list of ack vectors.
Reported-by: Jianwen Ji <jiji@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b20e2d5478 ]
aszlig observed failing ssh tunnels (-w) during initialization since
commit cc9da6cc4f ("ipv6: addrconf: use stable address generator for
ARPHRD_NONE"). We already had reports that the mentioned commit breaks
Juniper VPN connections. I can't clearly say that the Juniper VPN client
has the same problem, but it is worth a try to hint to this patch.
Because of the early generation of link local addresses, the kernel now
can start asking for routers on the local subnet much earlier than usual.
Those router solicitation packets arrive inside the ssh channels and
should be transmitted to the tun fd before the configuration scripts
might have upped the interface and made it ready for transmission.
ssh polls on the interface and receives back a POLL_OUT. It tries to send
the earily router solicitation packet to the tun interface. Unfortunately
it hasn't been up'ed yet by config scripts, thus failing with -EIO. ssh
doesn't retry again and considers the tun interface broken forever.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=121131
Fixes: cc9da6cc4f ("ipv6: addrconf: use stable address generator for ARPHRD_NONE")
Cc: Bjørn Mork <bjorn@mork.no>
Reported-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Cc: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Reported-by: Jonas Lippuner <jonas@lippuner.ca>
Cc: Jonas Lippuner <jonas@lippuner.ca>
Reported-by: aszlig <aszlig@redmoonstudios.org>
Cc: aszlig <aszlig@redmoonstudios.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 45caeaa5ac ]
As Eric Dumazet pointed out this also needs to be fixed in IPv6.
v2: Contains the IPv6 tcp/Ipv6 dccp patches as well.
We have seen a few incidents lately where a dst_enty has been freed
with a dangling TCP socket reference (sk->sk_dst_cache) pointing to that
dst_entry. If the conditions/timings are right a crash then ensues when the
freed dst_entry is referenced later on. A Common crashing back trace is:
#8 [] page_fault at ffffffff8163e648
[exception RIP: __tcp_ack_snd_check+74]
.
.
#9 [] tcp_rcv_established at ffffffff81580b64
#10 [] tcp_v4_do_rcv at ffffffff8158b54a
#11 [] tcp_v4_rcv at ffffffff8158cd02
#12 [] ip_local_deliver_finish at ffffffff815668f4
#13 [] ip_local_deliver at ffffffff81566bd9
#14 [] ip_rcv_finish at ffffffff8156656d
#15 [] ip_rcv at ffffffff81566f06
#16 [] __netif_receive_skb_core at ffffffff8152b3a2
#17 [] __netif_receive_skb at ffffffff8152b608
#18 [] netif_receive_skb at ffffffff8152b690
#19 [] vmxnet3_rq_rx_complete at ffffffffa015eeaf [vmxnet3]
#20 [] vmxnet3_poll_rx_only at ffffffffa015f32a [vmxnet3]
#21 [] net_rx_action at ffffffff8152bac2
#22 [] __do_softirq at ffffffff81084b4f
#23 [] call_softirq at ffffffff8164845c
#24 [] do_softirq at ffffffff81016fc5
#25 [] irq_exit at ffffffff81084ee5
#26 [] do_IRQ at ffffffff81648ff8
Of course it may happen with other NIC drivers as well.
It's found the freed dst_entry here:
224 static bool tcp_in_quickack_mode(struct sock *sk)↩
225 {↩
226 ▹ const struct inet_connection_sock *icsk = inet_csk(sk);↩
227 ▹ const struct dst_entry *dst = __sk_dst_get(sk);↩
228 ↩
229 ▹ return (dst && dst_metric(dst, RTAX_QUICKACK)) ||↩
230 ▹ ▹ (icsk->icsk_ack.quick && !icsk->icsk_ack.pingpong);↩
231 }↩
But there are other backtraces attributed to the same freed dst_entry in
netfilter code as well.
All the vmcores showed 2 significant clues:
- Remote hosts behind the default gateway had always been redirected to a
different gateway. A rtable/dst_entry will be added for that host. Making
more dst_entrys with lower reference counts. Making this more probable.
- All vmcores showed a postitive LockDroppedIcmps value, e.g:
LockDroppedIcmps 267
A closer look at the tcp_v4_err() handler revealed that do_redirect() will run
regardless of whether user space has the socket locked. This can result in a
race condition where the same dst_entry cached in sk->sk_dst_entry can be
decremented twice for the same socket via:
do_redirect()->__sk_dst_check()-> dst_release().
Which leads to the dst_entry being prematurely freed with another socket
pointing to it via sk->sk_dst_cache and a subsequent crash.
To fix this skip do_redirect() if usespace has the socket locked. Instead let
the redirect take place later when user space does not have the socket
locked.
The dccp/IPv6 code is very similar in this respect, so fixing it there too.
As Eric Garver pointed out the following commit now invalidates routes. Which
can set the dst->obsolete flag so that ipv4_dst_check() returns null and
triggers the dst_release().
Fixes: ceb3320610 ("ipv4: Kill routes during PMTU/redirect updates.")
Cc: Eric Garver <egarver@redhat.com>
Cc: Hannes Sowa <hsowa@redhat.com>
Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 91864f5852 ]
The previous idea was to check whether a net namespace is in
net_exit_list or not. It doesn't work, because net->exit_list is used in
__register_pernet_operations and __unregister_pernet_operations where
all namespaces are added to a temporary list to make cleanup in a error
case, so list_empty(&net->exit_list) always returns false.
Reported-by: Mantas Mikulėnas <grawity@gmail.com>
Fixes: 002d8a1a6c ("net: skip genenerating uevents for network namespaces that are exiting")
Signed-off-by: Andrei Vagin <avagin@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a13b2082ec ]
Andreas reports kernel oops during rmmod of the br_netfilter module.
Hannes debugged the oops down to a NULL rt6info->rt6i_indev.
Problem is that br_netfilter has the nasty concept of adding a fake
rtable to skb->dst; this happens in a br_netfilter prerouting hook.
A second hook (in bridge LOCAL_IN) is supposed to remove these again
before the skb is handed up the stack.
However, on module unload hooks get unregistered which means an
skb could traverse the prerouting hook that attaches the fake_rtable,
while the 'fake rtable remove' hook gets removed from the hooklist
immediately after.
Fixes: 34666d467c ("netfilter: bridge: move br_netfilter out of the core")
Reported-by: Andreas Karis <akaris@redhat.com>
Debugged-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 79e49503ef ]
ip6_fragment, in case skb has a fraglist, checks if the
skb is cloned. If it is, it will move to the 'slow path' and allocates
new skbs for each fragment.
However, right before entering the slowpath loop, it updates the
nexthdr value of the last ipv6 extension header to NEXTHDR_FRAGMENT,
to account for the fragment header that will be inserted in the new
ipv6-fragment skbs.
In case original skb is cloned this munges nexthdr value of another
skb. Avoid this by doing the nexthdr update for each of the new fragment
skbs separately.
This was observed with tcpdump on a bridge device where netfilter ipv6
reassembly is active: tcpdump shows malformed fragment headers as
the l4 header (icmpv6, tcp, etc). is decoded as a fragment header.
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Reported-by: Andreas Karis <akaris@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 67e194007b ]
Commit 2759647247 ("ipv6: fix ECMP route replacement") introduced a
loop that removes all siblings of an ECMP route that is being
replaced. However, this loop doesn't stop when it has replaced
siblings, and keeps removing other routes with a higher metric.
We also end up triggering the WARN_ON after the loop, because after
this nsiblings < 0.
Instead, stop the loop when we have taken care of all routes with the
same metric as the route being replaced.
Reproducer:
===========
#!/bin/sh
ip netns add ns1
ip netns add ns2
ip -net ns1 link set lo up
for x in 0 1 2 ; do
ip link add veth$x netns ns2 type veth peer name eth$x netns ns1
ip -net ns1 link set eth$x up
ip -net ns2 link set veth$x up
done
ip -net ns1 -6 r a 2000::/64 nexthop via fe80::0 dev eth0 \
nexthop via fe80::1 dev eth1 nexthop via fe80::2 dev eth2
ip -net ns1 -6 r a 2000::/64 via fe80::42 dev eth0 metric 256
ip -net ns1 -6 r a 2000::/64 via fe80::43 dev eth0 metric 2048
echo "before replace, 3 routes"
ip -net ns1 -6 r | grep -v '^fe80\|^ff00'
echo
ip -net ns1 -6 r c 2000::/64 nexthop via fe80::4 dev eth0 \
nexthop via fe80::5 dev eth1 nexthop via fe80::6 dev eth2
echo "after replace, only 2 routes, metric 2048 is gone"
ip -net ns1 -6 r | grep -v '^fe80\|^ff00'
Fixes: 2759647247 ("ipv6: fix ECMP route replacement")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 79099aab38 ]
Multipath routes can be rendered usesless when a device in one of the
paths is deleted. For example:
$ ip -f mpls ro ls
100
nexthop as to 200 via inet 172.16.2.2 dev virt12
nexthop as to 300 via inet 172.16.3.2 dev br0
101
nexthop as to 201 via inet6 2000:2::2 dev virt12
nexthop as to 301 via inet6 2000:3::2 dev br0
$ ip li del br0
When br0 is deleted the other hop is not considered in
mpls_select_multipath because of the alive check -- rt_nhn_alive
is 0.
rt_nhn_alive is decremented once in mpls_ifdown when the device is taken
down (NETDEV_DOWN) and again when it is deleted (NETDEV_UNREGISTER). For
a 2 hop route, deleting one device drops the alive count to 0. Since
devices are taken down before unregistering, the decrement on
NETDEV_UNREGISTER is redundant.
Fixes: c89359a42e ("mpls: support for dead routes")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e37791ec1a ]
When the mpls_router module is unloaded, mpls routes are deleted but
notifications are not sent to userspace leaving userspace caches
out of sync. Add the call to mpls_notify_route in mpls_net_exit as
routes are freed.
Fixes: 0189197f44 ("mpls: Basic routing support")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d7aba644ff ]
Depending on the hardware, the amd-xgbe driver may use disable_irq_nosync()
and enable_irq() when an interrupt is received to process Rx packets. If
the napi_complete_done() return value isn't checked an unbalanced enable
for the IRQ could result, generating a warning stack trace.
Update the driver to only enable interrupts if napi_complete_done() returns
true.
Reported-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 745cb7f8a5 ]
Replace MAX_ADDR_LEN with its numeric value to fix the following
linux/packet_diag.h userspace compilation error:
/usr/include/linux/packet_diag.h:67:17: error: 'MAX_ADDR_LEN' undeclared here (not in a function)
__u8 pdmc_addr[MAX_ADDR_LEN];
This is not the first case in the UAPI where the numeric value
of MAX_ADDR_LEN is used instead of symbolic one, uapi/linux/if_link.h
already does the same:
$ grep MAX_ADDR_LEN include/uapi/linux/if_link.h
__u8 mac[32]; /* MAX_ADDR_LEN */
There are no UAPI headers besides these two that use MAX_ADDR_LEN.
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Acked-by: Pavel Emelyanov <xemul@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 294acf1c01 ]
The gso code of several tunnels type (gre and udp tunnels)
takes for granted that the skb->inner_protocol is properly
initialized and drops the packet elsewhere.
On the forwarding path no one is initializing such field,
so gro encapsulated packets are dropped on forward.
Since commit 3872035241 ("gre: Use inner_proto to obtain
inner header protocol"), this can be reproduced when the
encapsulated packets use gre as the tunneling protocol.
The issue happens also with vxlan and geneve tunnels since
commit 8bce6d7d0d ("udp: Generalize skb_udp_segment"), if the
forwarding host's ingress nic has h/w offload for such tunnel
and a vxlan/geneve device is configured on top of it, regardless
of the configured peer address and vni.
To address the issue, this change initialize the inner_protocol
field for encapsulated packets in both ipv4 and ipv6 gro complete
callbacks.
Fixes: 3872035241 ("gre: Use inner_proto to obtain inner header protocol")
Fixes: 8bce6d7d0d ("udp: Generalize skb_udp_segment")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3331aa378e ]
This restores the ability to set a team device's mtu to anything higher
than 1500. Similar to the reported issue with bonding, the team driver
calls ether_setup(), which sets an initial max_mtu of 1500, while the
underlying hardware can handle something much larger. Just set it to
ETH_MAX_MTU to support all possible values, and the limitations of the
underlying devices will prevent setting anything too large.
Fixes: 91572088e3 ("net: use core MTU range checking in core net infra")
CC: Cong Wang <xiyou.wangcong@gmail.com>
CC: Jiri Pirko <jiri@resnulli.us>
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9ac25fc063 ]
TX skbs do not necessarily hold a reference on skb->sk->sk_refcnt
By the time TX completion happens, sk_refcnt might be already 0.
sock_hold()/sock_put() would then corrupt critical state, like
sk_wmem_alloc and lead to leaks or use after free.
Fixes: 62bccb8cdb ("net-timestamp: Make the clone operation stand-alone from phy timestamping")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 02b2faaf0a ]
Dmitry Vyukov reported a divide by 0 triggered by syzkaller, exploiting
tcp_disconnect() path that was never really considered and/or used
before syzkaller ;)
I was not able to reproduce the bug, but it seems issues here are the
three possible actions that assumed they would never trigger on a
listener.
1) tcp_write_timer_handler
2) tcp_delack_timer_handler
3) MTU reduction
Only IPv6 MTU reduction was properly testing TCP_CLOSE and TCP_LISTEN
states from tcp_v6_mtu_reduced()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2697ea5a85 ]
If an SFP module is not present, xgbe_phy_sfp_phy_settings() should
return after applying the default settings. Currently there is no return
statement and the default settings are overwritten.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b42c6761fd ]
The MDIO register mode is set when the device is probed. But when the
device is brought down and then back up, the MDIO register mode has been
reset. Be sure to reset the mode during device startup and only change
the mode of the address specified.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 402168b4c2 ]
Some configurations require the use of the hardware's MDIO support to
communicate with external PHYs. The MDIO commands indicate completion
through the device interrupt. When bringing down the device the interrupts
were released before stopping the external PHY, resulting in MDIO command
timeouts. Move the stopping of the PHY to before the releasing of the
interrupts.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d5afb6f9b6 ]
The code where sk_clone() came from created a new socket and locked it,
but then, on the error path didn't unlock it.
This problem stayed there for a long while, till b0691c8ee7 ("net:
Unlock sock before calling sk_free()") fixed it, but unfortunately the
callers of sk_clone() (now sk_clone_locked()) were not audited and the
one in dccp_create_openreq_child() remained.
Now in the age of the syskaller fuzzer, this was finally uncovered, as
reported by Dmitry:
---- 8< ----
I've got the following report while running syzkaller fuzzer on
86292b33d4 ("Merge branch 'akpm' (patches from Andrew)")
[ BUG: held lock freed! ]
4.10.0+ #234 Not tainted
-------------------------
syz-executor6/6898 is freeing memory
ffff88006286cac0-ffff88006286d3b7, with a lock still held there!
(slock-AF_INET6){+.-...}, at: [<ffffffff8362c2c9>] spin_lock
include/linux/spinlock.h:299 [inline]
(slock-AF_INET6){+.-...}, at: [<ffffffff8362c2c9>]
sk_clone_lock+0x3d9/0x12c0 net/core/sock.c:1504
5 locks held by syz-executor6/6898:
#0: (sk_lock-AF_INET6){+.+.+.}, at: [<ffffffff839a34b4>] lock_sock
include/net/sock.h:1460 [inline]
#0: (sk_lock-AF_INET6){+.+.+.}, at: [<ffffffff839a34b4>]
inet_stream_connect+0x44/0xa0 net/ipv4/af_inet.c:681
#1: (rcu_read_lock){......}, at: [<ffffffff83bc1c2a>]
inet6_csk_xmit+0x12a/0x5d0 net/ipv6/inet6_connection_sock.c:126
#2: (rcu_read_lock){......}, at: [<ffffffff8369b424>] __skb_unlink
include/linux/skbuff.h:1767 [inline]
#2: (rcu_read_lock){......}, at: [<ffffffff8369b424>] __skb_dequeue
include/linux/skbuff.h:1783 [inline]
#2: (rcu_read_lock){......}, at: [<ffffffff8369b424>]
process_backlog+0x264/0x730 net/core/dev.c:4835
#3: (rcu_read_lock){......}, at: [<ffffffff83aeb5c0>]
ip6_input_finish+0x0/0x1700 net/ipv6/ip6_input.c:59
#4: (slock-AF_INET6){+.-...}, at: [<ffffffff8362c2c9>] spin_lock
include/linux/spinlock.h:299 [inline]
#4: (slock-AF_INET6){+.-...}, at: [<ffffffff8362c2c9>]
sk_clone_lock+0x3d9/0x12c0 net/core/sock.c:1504
Fix it just like was done by b0691c8ee7 ("net: Unlock sock before calling
sk_free()").
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20170301153510.GE15145@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 13baa00ad0 ]
It is now very clear that silly TCP listeners might play with
enabling/disabling timestamping while new children are added
to their accept queue.
Meaning net_enable_timestamp() can be called from BH context
while current state of the static key is not enabled.
Lets play safe and allow all contexts.
The work queue is scheduled only under the problematic cases,
which are the static key enable/disable transition, to not slow down
critical paths.
This extends and improves what we did in commit 5fa8bbda38 ("net: use
a work queue to defer net_disable_timestamp() work")
Fixes: b90e5794c5 ("net: dont call jump_label_dec from irq context")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8953de2f02 ]
Even with multicast flooding turned off, IPv6 ND should still work so
that IPv6 connectivity is provided. Allow this by continuing to flood
multicast traffic originated by us.
Fixes: b6cb5ac833 ("net: bridge: add per-port multicast flood flag")
Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Mike Manning <mmanning@brocade.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f7df4923fa ]
When the structure of the LPM tree changes (f.e., due to the addition of
a new prefix), we unbind the old tree and then bind the new one. This
may result in temporary packet loss.
Instead, overwrite the old binding with the new one.
Fixes: 6b75c4807d ("mlxsw: spectrum_router: Add virtual router management")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 51fb60eb16 ]
l2tp_ip_backlog_recv may not return -1 if the packet gets dropped.
The return value is passed up to ip_local_deliver_finish, which treats
negative values as an IP protocol number for resubmission.
Signed-off-by: Paul Hüber <phueber@kernsp.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit edb9d1bff4 ]
When tc actions are loaded as a module and no actions have been installed,
flushing them would result in actions removed from the memory, but modules
reference count not being decremented, so that the modules would not be
unloaded.
Following is example with GACT action:
% sudo modprobe act_gact
% lsmod
Module Size Used by
act_gact 16384 0
%
% sudo tc actions ls action gact
%
% sudo tc actions flush action gact
% lsmod
Module Size Used by
act_gact 16384 1
% sudo tc actions flush action gact
% lsmod
Module Size Used by
act_gact 16384 2
% sudo rmmod act_gact
rmmod: ERROR: Module act_gact is in use
....
After the fix:
% lsmod
Module Size Used by
act_gact 16384 0
%
% sudo tc actions add action pass index 1
% sudo tc actions add action pass index 2
% sudo tc actions add action pass index 3
% lsmod
Module Size Used by
act_gact 16384 3
%
% sudo tc actions flush action gact
% lsmod
Module Size Used by
act_gact 16384 0
%
% sudo tc actions flush action gact
% lsmod
Module Size Used by
act_gact 16384 0
% sudo rmmod act_gact
% lsmod
Module Size Used by
%
Fixes: f97017cdef ("net-sched: Fix actions flushing")
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2e3ce5bc2a ]
Commit b8607805dd ("sctp: not copying duplicate addrs to the assoc's
bind address list") tried to check for duplicate address before copying
to asoc's bind_addr list from global addr list.
But all the addrs' sin_ports in global addr list are 0 while the addrs'
sin_ports are bp->port in asoc's bind_addr list. It means even if it's
a duplicate address, af->cmp_addr will still return 0 as the their
sin_ports are different.
This patch is to fix it by setting the sin_port for addr param with
bp->port before comparing the addrs.
Fixes: b8607805dd ("sctp: not copying duplicate addrs to the assoc's bind address list")
Reported-by: Wei Chen <weichen@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8bcfd0925e ]
Avoid matching of random stack value for uid when rules
are looked up on input route or when RP filter is used.
Problem should affect only setups that use ip rules with
uid range.
Fixes: 622ec2c9d5 ("net: core: add UID to flows, rules, and routes")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1158632b5a ]
When using IPv6 transport and a default dst, a pointer to the configured
source address is passed into the route lookup. If no source address is
configured, then the value is overwritten.
IPv6 route lookup ignores egress ifindex match if the source address is set,
so if egress ifindex match is desired, the source address must be passed
as any. The overwrite breaks this for subsequent lookups.
Avoid this by copying the configured address to an existing stack variable
and pass a pointer to that instead.
Fixes: 272d96a5ab ("net: vxlan: lwt: Use source ip address during route lookup.")
Signed-off-by: Brian Russell <brussell@brocade.com>
Acked-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7dcdf941cd ]
Align vti6 with vti by returning GRE_KEY flag. This enables iproute2
to display tunnel keys on "ip -6 tunnel show"
Signed-off-by: David Forster <dforster@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dfcb9f4f99 ]
commit 2dcab59848 ("sctp: avoid BUG_ON on sctp_wait_for_sndbuf")
attempted to avoid a BUG_ON call when the association being used for a
sendmsg() is blocked waiting for more sndbuf and another thread did a
peeloff operation on such asoc, moving it to another socket.
As Ben Hutchings noticed, then in such case it would return without
locking back the socket and would cause two unlocks in a row.
Further analysis also revealed that it could allow a double free if the
application managed to peeloff the asoc that is created during the
sendmsg call, because then sctp_sendmsg() would try to free the asoc
that was created only for that call.
This patch takes another approach. It will deny the peeloff operation
if there is a thread sleeping on the asoc, so this situation doesn't
exist anymore. This avoids the issues described above and also honors
the syscalls that are already being handled (it can be multiple sendmsg
calls).
Joint work with Xin Long.
Fixes: 2dcab59848 ("sctp: avoid BUG_ON on sctp_wait_for_sndbuf")
Cc: Alexander Popov <alex.popov@linux.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 36154be40a ]
In cqe compression with striding RQ, the decompression of the CQE field
wqe_counter was done with a wrong wraparound value.
This caused handling cqes with a wrong pointer to wqe (rx descriptor)
and creating SKBs with wrong data, pointing to wrong (and already consumed)
strides/pages.
The meaning of the CQE field wqe_counter in striding RQ holds the
stride index instead of the WQE index. Hence, when decompressing
a CQE, wqe_counter should have wrapped-around the number of strides
in a single multi-packet WQE.
We dropped this wrap-around mask at all in CQE decompression of striding
RQ. It is not needed as in such cases the CQE compression session would
break because of different value of wqe_id field, starting a new
compression session.
Tested:
ethtool -K ethxx lro off/on
ethtool --set-priv-flags ethxx rx_cqe_compress on
super_netperf 16 {ipv4,ipv6} -t TCP_STREAM -m 50 -D
verified no csum errors and no page refcount issues.
Fixes: 7219ab34f1 ("net/mlx5e: CQE compression")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reported-by: Tom Herbert <tom@herbertland.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6dc4b54e77 ]
When the admin enables/disables cqe compression, updating
mpwqe stride size is required:
CQE compress ON ==> stride size = 256B
CQE compress OFF ==> stride size = 64B
This is already done on driver load via mlx5e_set_rq_type_params, all we
need is just to call it on arbitrary admin changes of cqe compression
state via priv flags or when changing timestamping state
(as it is mutually exclusive with cqe compression).
This bug introduces no functional damage, it only makes cqe compression
occur less often, since in ConnectX4-LX CQE compression is performed
only on packets smaller than stride size.
Tested:
ethtool --set-priv-flags ethxx rx_cqe_compress on
pktgen with 64 < pkt size < 256 and netperf TCP_STREAM (IPv4/IPv6)
verify `ethtool -S ethxx | grep compress` are advancing more often
(rapidly)
Fixes: 7219ab34f1 ("net/mlx5e: CQE compression")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b0d4660b4c ]
Some of RQ type parameters are derived from CQE compression state flag,
CQE compression flag was initialized only after RQ type parameters
setup. This leads to load RQ with stride size smaller than what we
want for when CQE compression is on.
This bug introduces no functional damage, it only makes CQE compression
occur less often, since in ConnectX4-LX CQE compression is performed
only on packets smaller than stride size.
Fix this by marking default status of CQE compression in PFLAG prior to
calling mlx5e_set_rq_priv_params(), as it inits some fields based on it.
Tested:
load driver on systems where rx CQE compress will be on (MH)
pktgen with 64 < pkt size < 256 and netperf TCP_STREAM (IPv4/IPv6)
verify `ethtool -S ethxx | grep compress` are advancing more often
(rapidly)
Fixes: 2fc4bfb725 ("net/mlx5e: Dynamic RQ type infrastructure")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4078e637c1 ]
When rq_type is Striding RQ, no room of SKB_RESERVE is needed
as SKB allocation is not done via build_skb.
Fixes: e4b8550807 ("net/mlx5e: Slightly reduce hardware LRO size")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6f08a22c5f ]
Currently vport representors are added only on driver load and removed on
driver unload. Apparently we forgot to handle them when we added the
seamless reset flow feature. This caused to leave the representors
netdevs alive and active with open HW resources on pci shutdown and on
error reset flows.
To overcome this we move their handling to interface attach/detach, so
they would be cleaned up on shutdown and recreated on reset flows.
Fixes: 26e59d8077 ("net/mlx5e: Implement mlx5e interface attach/detach callbacks")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45bded2c21 upstream.
Make sure that the Q counters are supported by the FW before trying
to allocate/deallocte them, this will avoid driver load failure when
they aren't supported by the FW.
Fixes: 0837e86a7a ('IB/mlx5: Add per port counters')
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0d06863f90 upstream.
Fix a BUG when the kernel tries to mount a file system constructed as
follows:
echo foo > foo.txt
mke2fs -Fq -t ext4 -O encrypt foo.img 100
debugfs -w foo.img << EOF
write foo.txt a
set_inode_field a i_flags 0x80800
set_super_value s_last_orphan 12
quit
EOF
root@kvm-xfstests:~# mount -o loop foo.img /mnt
[ 160.238770] ------------[ cut here ]------------
[ 160.240106] kernel BUG at /usr/projects/linux/ext4/fs/ext4/inode.c:3874!
[ 160.240106] invalid opcode: 0000 [#1] SMP
[ 160.240106] Modules linked in:
[ 160.240106] CPU: 0 PID: 2547 Comm: mount Tainted: G W 4.10.0-rc3-00034-gcdd33b941b67 #227
[ 160.240106] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.1-1 04/01/2014
[ 160.240106] task: f4518000 task.stack: f47b6000
[ 160.240106] EIP: ext4_block_zero_page_range+0x1a7/0x2b4
[ 160.240106] EFLAGS: 00010246 CPU: 0
[ 160.240106] EAX: 00000001 EBX: f7be4b50 ECX: f47b7dc0 EDX: 00000007
[ 160.240106] ESI: f43b05a8 EDI: f43babec EBP: f47b7dd0 ESP: f47b7dac
[ 160.240106] DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
[ 160.240106] CR0: 80050033 CR2: bfd85b08 CR3: 34a00680 CR4: 000006f0
[ 160.240106] Call Trace:
[ 160.240106] ext4_truncate+0x1e9/0x3e5
[ 160.240106] ext4_fill_super+0x286f/0x2b1e
[ 160.240106] ? set_blocksize+0x2e/0x7e
[ 160.240106] mount_bdev+0x114/0x15f
[ 160.240106] ext4_mount+0x15/0x17
[ 160.240106] ? ext4_calculate_overhead+0x39d/0x39d
[ 160.240106] mount_fs+0x58/0x115
[ 160.240106] vfs_kern_mount+0x4b/0xae
[ 160.240106] do_mount+0x671/0x8c3
[ 160.240106] ? _copy_from_user+0x70/0x83
[ 160.240106] ? strndup_user+0x31/0x46
[ 160.240106] SyS_mount+0x57/0x7b
[ 160.240106] do_int80_syscall_32+0x4f/0x61
[ 160.240106] entry_INT80_32+0x2f/0x2f
[ 160.240106] EIP: 0xb76b919e
[ 160.240106] EFLAGS: 00000246 CPU: 0
[ 160.240106] EAX: ffffffda EBX: 08053838 ECX: 08052188 EDX: 080537e8
[ 160.240106] ESI: c0ed0000 EDI: 00000000 EBP: 080537e8 ESP: bfa13660
[ 160.240106] DS: 007b ES: 007b FS: 0000 GS: 0033 SS: 007b
[ 160.240106] Code: 59 8b 00 a8 01 0f 84 09 01 00 00 8b 07 66 25 00 f0 66 3d 00 80 75 61 89 f8 e8 3e e2 ff ff 84 c0 74 56 83 bf 48 02 00 00 00 75 02 <0f> 0b 81 7d e8 00 10 00 00 74 02 0f 0b 8b 43 04 8b 53 08 31 c9
[ 160.240106] EIP: ext4_block_zero_page_range+0x1a7/0x2b4 SS:ESP: 0068:f47b7dac
[ 160.317241] ---[ end trace d6a773a375c810a5 ]---
The problem is that when the kernel tries to truncate an inode in
ext4_truncate(), it tries to clear any on-disk data beyond i_size.
Without the encryption key, it can't do that, and so it triggers a
BUG.
E2fsck does *not* provide this service, and in practice most file
systems have their orphan list processed by e2fsck, so to avoid
crashing, this patch skips this step if we don't have access to the
encryption key (which is the case when processing the orphan list; in
all other cases, we will have the encryption key, or the kernel
wouldn't have allowed the file to be opened).
An open question is whether the fact that e2fsck isn't clearing the
bytes beyond i_size causing problems --- and if we've lived with it
not doing it for so long, can we drop this from the kernel replay of
the orphan list in all cases (not just when we don't have the key for
encrypted inodes).
Addresses-Google-Bug: #35209576
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 413808685d upstream.
When the protocol is set via the sysfs protocols attribute, the
decoder is loaded. However, when it is not when a device is first
plugged in or registered.
Fixes: acc1c3c ("[media] media: rc: load decoder modules on-demand")
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d67a5f4b59 upstream.
Commit df2cb6daa4 ("block: Avoid deadlocks with bio allocation by
stacking drivers") created a workqueue for every bio set and code
in bio_alloc_bioset() that tries to resolve some low-memory deadlocks
by redirecting bios queued on current->bio_list to the workqueue if the
system is low on memory. However other deadlocks (see below **) may
happen, without any low memory condition, because generic_make_request
is queuing bios to current->bio_list (rather than submitting them).
** the related dm-snapshot deadlock is detailed here:
https://www.redhat.com/archives/dm-devel/2016-July/msg00065.html
Fix this deadlock by redirecting any bios on current->bio_list to the
bio_set's rescue workqueue on every schedule() call. Consequently,
when the process blocks on a mutex, the bios queued on
current->bio_list are dispatched to independent workqueus and they can
complete without waiting for the mutex to be available.
The structure blk_plug contains an entry cb_list and this list can contain
arbitrary callback functions that are called when the process blocks.
To implement this fix DM (ab)uses the onstack plug's cb_list interface
to get its flush_current_bio_list() called at schedule() time.
This fixes the snapshot deadlock - if the map method blocks,
flush_current_bio_list() will be called and it redirects bios waiting
on current->bio_list to appropriate workqueues.
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1267650
Depends-on: df2cb6daa4 ("block: Avoid deadlocks with bio allocation by stacking drivers")
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0265634eb9 upstream.
When the interrupt requested with devm_request_irq(), serial_ir.rcdev
is still null so will cause null deference if the irq handler is called
early on.
Also ensure that timeout_timer is setup.
Link: http://lkml.kernel.org/r/CA+55aFxsh2uF8gi5sN_guY3Z+tiLv7LpJYKBw+y8vqLzp+TsnQ@mail.gmail.com
[mchehab@s-opensource.com: moved serial_ir_probe() back to its original place]
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d8e9b2b909 upstream.
send_display_send_uevent() sends two environment variable, and the
first one GVT_DISPLAY_READY is set including a new line at the end of
the string; that is obviously superfluous and wrong -- at least, it
*looks* so when you only read the code.
However, it doesn't appear in the actual output by a (supposedly
unexpected) trick. The code uses snprintf() and truncates the string
in size 20 bytes. This makes the string as GVT_DISPLAY_READY=0 or
...=1 including the trailing NUL-letter. That is, the '\n' found in
the format string is always cut off as a result.
Although the code gives the correct result, it is confusing. This
patch addresses it, just removing the superfluous '\n' from the format
string for avoiding further confusion. If the argument "ready" were
not a bool, the size 20 should be corrected as well. But it's a
bool, so we can leave the magic number 20 as is for now.
FWIW, the bug was spotted by a new GCC7 warning:
drivers/gpu/drm/i915/gvt/handlers.c: In function 'pvinfo_mmio_write':
drivers/gpu/drm/i915/gvt/handlers.c:1042:34: error: 'snprintf' output truncated before the last format character [-Werror=format-truncation=]
snprintf(display_ready_str, 20, "GVT_DISPLAY_READY=%d\n", ready);
^~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/i915/gvt/handlers.c:1042:2: note: 'snprintf' output 21 bytes into a destination of size 20
snprintf(display_ready_str, 20, "GVT_DISPLAY_READY=%d\n", ready);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: 04d348ae3f ("drm/i915/gvt: vGPU display virtualization")
Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=1025903
Reported-by: Richard Biener <rguenther@suse.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 370a0ec181 upstream.
Currently, if a vcpu thread tries to change the active state of an
interrupt which is already on the same vcpu's AP list, it will loop
forever. Since the VGIC mmio handler is called after a vcpu has
already synced back the LR state to the struct vgic_irq, we can just
let it proceed safely.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Jintack Lim <jintack@cs.columbia.edu>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e4d88009f upstream.
While we can technically not run huge page guests right now, we can
setup a guest with huge pages. Trying to migrate it will trigger a
VM_BUG_ON and, if the kernel is not configured to panic on a BUG, it
will happily try to work on non-existing page table entries.
With this patch, we always return "dirty" if we encounter a large page
when migrating. This at least fixes the immediate problem until we
have proper handling for both kind of pages.
Fixes: 15f36eb ("KVM: s390: Add proper dirty bitmap support to S390 kvm.")
Signed-off-by: Janosch Frank <frankja@linux.vnet.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f98c7bce57 upstream.
If DMA is not available (even when configured in DeviceTree), the driver
will fail the startup procedure thus making serial console not
available.
For example this causes boot failure on QEMU ARMv7 (Exynos4210, SMDKC210):
[ 1.302575] OF: amba_device_add() failed (-19) for /amba/pdma@12680000
...
[ 11.435732] samsung-uart 13800000.serial: DMA request failed
[ 72.963893] samsung-uart 13800000.serial: DMA request failed
[ 73.143361] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000000
DMA is not necessary for serial to work, so continue with UART startup
after emitting a warning.
Fixes: 62c37eedb7 ("serial: samsung: add dma reqest/release functions")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 654b404f2a upstream.
Add missing sanity check to the bulk-in completion handler to avoid an
integer underflow that can be triggered by a malicious device.
This avoids leaking 128 kB of memory content from after the URB transfer
buffer to user space.
Fixes: 8c209e6782 ("USB: make actual_length in struct urb field u32")
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0b1d250afb upstream.
Fix a NULL-pointer dereference in the interrupt callback should a
malicious device send data containing a bad port number by adding the
missing sanity check.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit de46e56653 upstream.
Make sure to verify that we have the required interrupt-out endpoint for
IOWarrior56 devices to avoid dereferencing a NULL-pointer in write
should a malicious device lack such an endpoint.
Fixes: 946b960d13 ("USB: add driver for iowarrior devices.")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b7321e81fc upstream.
Make sure to check for the required interrupt-in endpoint to avoid
dereferencing a NULL-pointer should a malicious device lack such an
endpoint.
Note that a fairly recent change purported to fix this issue, but added
an insufficient test on the number of endpoints only, a test which can
now be removed.
Fixes: 4ec0ef3a82 ("USB: iowarrior: fix oops with malicious USB descriptors")
Fixes: 946b960d13 ("USB: add driver for iowarrior devices.")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 30572418b4 upstream.
This driver needlessly took another reference to the tty on open, a
reference which was then never released on close. This lead to not just
a leak of the tty, but also a driver reference leak that prevented the
driver from being unloaded after a port had once been opened.
Fixes: 4a90f09b20 ("tty: usb-serial krefs")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c76d7cd52 upstream.
Add missing sanity check to the bulk-in completion handler to avoid an
integer underflow that could be triggered by a malicious device.
This avoids leaking up to 56 bytes from after the URB transfer buffer to
user space.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dcc7620cad upstream.
Upstream commit 98d74f9cea ("xhci: fix 10 second timeout on removal of
PCI hotpluggable xhci controllers") fixes a problem with hot pluggable PCI
xhci controllers which can result in excessive timeouts, to the point where
the system reports a deadlock.
The same problem is seen with hot pluggable xhci controllers using the
xhci-plat driver, such as the driver used for Type-C ports on rk3399.
Similar to hot-pluggable PCI controllers, the driver for this chip
removes the xhci controller from the system when the Type-C cable is
disconnected.
The solution for PCI devices works just as well for non-PCI devices
and avoids the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f95e60a7db upstream.
According to xHCI spec, HCIVERSION containing a BCD encoding
of the xHCI specification revision number, 0100h corresponds
to xHCI version 1.0. Change "100" as "0x100".
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Fixes: 04abb6de28 ("xhci: Read and parse new xhci 1.1 capability register")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eb38d913c2 upstream.
This reverts commit 4fbac5206a.
This commit breaks g_webcam when used with uvc-gadget [1].
The user space application (e.g. uvc-gadget) is responsible for
sending response to UVC class specific requests on control endpoint
in uvc_send_response() in uvc_v4l2.c.
The bad commit was causing a duplicate response to be sent with
incorrect response data thus causing UVC probe to fail at the host
and broken control transfer endpoint at the gadget.
[1] - git://git.ideasonboard.org/uvc-gadget.git
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2bfa0719ac upstream.
If we're dealing with SuperSpeed endpoints, we need
to make sure to pass along the companion descriptor
and initialize fields needed by the Gadget
API. Eventually, f_fs.c should be converted to use
config_ep_by_speed() like all other functions,
though.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 85550f9148 upstream.
In patch 2e2aa1bc7eff90ecm, USB suspend and wakeup control requests are
passed to SFR_OHCIICR register. If a processor does not have such a
register, this hub control request will be dropped.
If no such a SFR register is available, all USB suspend control requests
will now be processed using ohci_hub_control()
(like before patch 2e2aa1bc7eff90ecm.)
Tested on an Atmel AT91SAM9G20 with an on-board TI TUSB2046B hub chip
If the last USB device is unplugged from the USB hub, the hub goes into
sleep and will not wakeup when an USB devices is inserted.
Fixes: 2e2aa1bc7e ("usb: ohci-at91: Forcibly suspend ports while USB suspend")
Signed-off-by: Jelle Martijn Kok <jmkok@youcom.nl>
Tested-by: Wenyou Yang <wenyou.yang@atmel.com>
Cc: Wenyou Yang <wenyou.yang@atmel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7369090a9f upstream.
Some gadget drivers are bad, bad boys. We notice
that ADB was passing bad Burst Size which caused top
bits of param0 to be overwritten which confused DWC3
when running this command.
In order to avoid future issues, we're going to make
sure values passed by macros are always safe for the
controller. Note that ADB still needs a fix to *not*
pass bad values.
Reported-by: Mohamed Abbas <mohamed.abbas@intel.com>
Sugested-by: Adam Andruszak <adam.andruszak@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a69e2fb703 upstream.
The CPPR (Current Processor Priority Register) of a XICS interrupt
presentation controller contains a value N, such that only interrupts
with a priority "more favoured" than N will be received by the CPU,
where "more favoured" means "less than". So if the CPPR has the value 5
then only interrupts with a priority of 0-4 inclusive will be received.
In theory the CPPR can support a value of 0 to 255 inclusive.
In practice Linux only uses values of 0, 4, 5 and 0xff. Setting the CPPR
to 0 rejects all interrupts, setting it to 0xff allows all interrupts.
The values 4 and 5 are used to differentiate IPIs from external
interrupts. Setting the CPPR to 5 allows IPIs to be received but not
external interrupts.
The CPPR emulation in the OPAL XICS implementation only directly
supports priorities 0 and 0xff. All other priorities are considered
equivalent, and mapped to a single priority value internally. This means
when using icp-opal we can not allow IPIs but not externals.
This breaks Linux's use of priority values when a CPU is hot unplugged.
After migrating IRQs away from the CPU that is being offlined, we set
the priority to 5, meaning we still want the offline CPU to receive
IPIs. But the effect of the OPAL XICS emulation's use of a single
priority value is that all interrupts are rejected by the CPU. With the
CPU offline, and not receiving IPIs, we may not be able to wake it up to
bring it back online.
The first part of the fix is in icp_opal_set_cpu_priority(). CPPR values
of 0 to 4 inclusive will correctly cause all interrupts to be rejected,
so we pass those CPPR values through to OPAL. However if we are called
with a CPPR of 5 or greater, the caller is expecting to be able to allow
IPIs but not external interrupts. We know this doesn't work, so instead
of rejecting all interrupts we choose the opposite which is to allow all
interrupts. This is still not correct behaviour, but we know for the
only existing caller (xics_migrate_irqs_away()), that it is the better
option.
The other part of the fix is in xics_migrate_irqs_away(). Instead of
setting priority (CPPR) to 0, and then back to 5 before migrating IRQs,
we migrate the IRQs before setting the priority back to 5. This should
have no effect on an ICP backend with a working set_priority(), and on
icp-opal it means we will keep all interrupts blocked until after we've
finished doing the IRQ migration. Additionally we wait for 5ms after
doing the migration to make sure there are no IRQs in flight.
Fixes: d74361881f ("powerpc/xics: Add ICP OPAL backend")
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Reported-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Tested-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
[mpe: Rewrote comments and change log, change delay to 5ms]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3fb66a70a4 upstream.
On 32-bit book-e machines, hugepd_ok() no longer takes into account null
hugepd values, causing this crash at boot:
Unable to handle kernel paging request for data at address 0x80000000
...
NIP [c0018378] follow_huge_addr+0x38/0xf0
LR [c001836c] follow_huge_addr+0x2c/0xf0
Call Trace:
follow_huge_addr+0x2c/0xf0 (unreliable)
follow_page_mask+0x40/0x3e0
__get_user_pages+0xc8/0x450
get_user_pages_remote+0x8c/0x250
copy_strings+0x110/0x390
copy_strings_kernel+0x2c/0x50
do_execveat_common+0x478/0x630
do_execve+0x2c/0x40
try_to_run_init_process+0x18/0x60
kernel_init+0xbc/0x110
ret_from_kernel_thread+0x5c/0x64
This impacts all nxp (ex-freescale) 32-bit booke platforms.
This was caused by the change of hugepd_t.pd from signed to unsigned,
and the update to the nohash version of hugepd_ok(). Previously
hugepd_ok() could exclude all non-huge and NULL pgds using > 0, whereas
now we need to explicitly check that the value is not zero and also that
PD_HUGE is *clear*.
This isn't protected by the pgd_none() check in __find_linux_pte_or_hugepte()
because on 32-bit we use pgtable-nopud.h, which causes the pgd_none()
check to be always false.
Fixes: 20717e1ff5 ("powerpc/mm: Fix little-endian 4K hugetlb")
Reported-by: Madalin-Cristian Bucur <madalin.bucur@nxp.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
[mpe: Flesh out change log details.]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e148bd17f4 upstream.
emulate_step() uses a number of underlying kernel functions that were
initially not enabled for LE. This has been rectified since. So, fix
emulate_step() for LE for the corresponding instructions.
Reported-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 606142af57 upstream.
On Kernel 4.9, WARNINGs about doing DMA on stack are hit at
the dw2102 driver: one in su3000_power_ctrl() and the other in tt_s2_4600_frontend_attach().
Both were due to the use of buffers on the stack as parameters to
dvb_usb_generic_rw() and the resulting attempt to do DMA with them.
The device was non-functional as a result.
So, switch this driver over to use a buffer within the device state
structure, as has been done with other DVB-USB drivers.
Tested with TechnoTrend TT-connect S2-4600.
[mchehab@osg.samsung.com: fixed a warning at su3000_i2c_transfer() that
state var were dereferenced before check 'd']
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d1eb98143c upstream.
On ARM and arm64, we use a dedicated mm_struct to map the UEFI
Runtime Services regions, which allows us to map those regions
on demand, and in a way that is guaranteed to be compatible
with incoming kernels across kexec.
As it turns out, we don't fully initialize the mm_struct in the
same way as process mm_structs are initialized on fork(), which
results in the following crash on ARM if CONFIG_CPUMASK_OFFSTACK=y
is enabled:
...
EFI Variables Facility v0.08 2004-May-17
Unable to handle kernel NULL pointer dereference at virtual address 00000000
[...]
Process swapper/0 (pid: 1)
...
__memzero()
check_and_switch_context()
virt_efi_get_next_variable()
efivar_init()
efivars_sysfs_init()
do_one_initcall()
...
This is due to a missing call to mm_init_cpumask(), so add it.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/1488395154-29786-1-git-send-email-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 040757f738 upstream.
Always increment/decrement ucount->count under the ucounts_lock. The
increments are there already and moving the decrements there means the
locking logic of the code is simpler. This simplification in the
locking logic fixes a race between put_ucounts and get_ucounts that
could result in a use-after-free because the count could go zero then
be found by get_ucounts and then be freed by put_ucounts.
A bug presumably this one was found by a combination of syzkaller and
KASAN. JongWhan Kim reported the syzkaller failure and Dmitry Vyukov
spotted the race in the code.
Fixes: f6b2db1a3e ("userns: Make the count of user namespaces per user")
Reported-by: JongHwan Kim <zzoru007@gmail.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Reviewed-by: Andrei Vagin <avagin@gmail.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf7165cfa2 upstream.
There are several trace include files that define TRACE_INCLUDE_FILE.
Include several of them in the same .c file (as I currently have in
some code I am working on), and the compile will blow up with a
"warning: "TRACE_INCLUDE_FILE" redefined #define TRACE_INCLUDE_FILE syscalls"
Every other include file in include/trace/events/ avoids that issue
by having a #undef TRACE_INCLUDE_FILE before the #define; syscalls.h
should have one, too.
Link: http://lkml.kernel.org/r/20160928225554.13bd7ac6@annuminas.surriel.com
Fixes: b8007ef742 ("tracing: Separate raw syscall from syscall tracer")
Signed-off-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ababb08938 upstream.
Since commit e247454103 ("bcm2835: Fix hang for writing messages
larger than 16 bytes") the interrupt handler is prone to a possible
NULL pointer dereference. This could happen if an interrupt fires
before curr_msg is set by bcm2835_i2c_xfer_msg() and randomly occurs
on the RPi 3. Even this is an unexpected behavior the driver must
handle that with an error instead of a crash.
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Fixes: e247454103 ("bcm2835: Fix hang for writing messages larger than 16 bytes")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 906b268477 upstream.
kernelci.org reports a warning for this driver, as it copies a local
variable into a 'const char *' string:
drivers/mtd/maps/pmcmsp-flash.c:149:30: warning: passing argument 1 of 'strncpy' discards 'const' qualifier from pointer target type [-Wdiscarded-qualifiers]
Using kstrndup() simplifies the code and avoids the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23ca9b5223 upstream.
kernelci reports a failure of the ip28_defconfig build after upgrading its
gcc version:
arch/mips/sgi-ip22/Platform:29: *** gcc doesn't support needed option -mr10k-cache-barrier=store. Stop.
The problem apparently is that the -mr10k-cache-barrier=store option is now
rejected for CPUs other than r10k. Explicitly including the CPU in the
check fixes this and is safe because both options were introduced in
gcc-4.4.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/15049/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b617649468 upstream.
One of the last remaining failures in kernelci.org is for a gcc bug:
drivers/net/ethernet/qlogic/qlge/qlge_main.c:4819:1: error: insn does not satisfy its constraints:
drivers/net/ethernet/qlogic/qlge/qlge_main.c:4819:1: internal compiler error: in extract_constrain_insn, at recog.c:2190
This is apparently broken in gcc-6 but fixed in gcc-7, and I cannot
reproduce the problem here. However, it is clear that ip27_defconfig
does not actually need this driver as the platform has only PCI-X but
not PCIe, and the qlge adapter in turn is PCIe-only.
The driver was originally enabled in 2010 along with lots of other
drivers.
Fixes: 59d302b342 ("MIPS: IP27: Make defconfig useful again.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/15197/
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1742ac2650 upstream.
vdso.h includes <spaces.h> implicitly after defining CONFIG_32BITS.
This defeats the override in mach-ip27/spaces.h, leading to
a build error that shows up in kernelci.org:
In file included from arch/mips/include/asm/mach-ip27/spaces.h:29:0,
from arch/mips/include/asm/page.h:12,
from arch/mips/vdso/vdso.h:26,
from arch/mips/vdso/gettimeofday.c:11:
arch/mips/include/asm/mach-generic/spaces.h:28:0: error: "CAC_BASE" redefined [-Werror]
#define CAC_BASE _AC(0x80000000, UL)
An earlier patch tried to make the second definition conditional,
but that patch had the #ifdef in the wrong place, and would lead
to another warning:
arch/mips/include/asm/io.h: In function 'phys_to_virt':
arch/mips/include/asm/io.h:138:9: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
For all I can tell, there is no other reason than vdso32 to ever
include this file with CONFIG_32BITS set, and the vdso itself should
never refer to the base addresses as it is running in user space,
so adding an #ifdef here is safe.
Link: https://patchwork.kernel.org/patch/9418187/
Fixes: 3ffc17d876 ("MIPS: Adjust MIPS64 CAC_BASE to reflect Config.K0")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/15039/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9ddc16ad8e upstream.
In linux-4.10-rc, NF_CT_PROTO_UDPLITE and NF_CT_PROTO_DCCP are bool
symbols instead of tristate, and kernelci.org reports a bunch of
warnings for this, like:
arch/mips/configs/malta_kvm_guest_defconfig:63:warning: symbol value 'm' invalid for NF_CT_PROTO_UDPLITE
arch/mips/configs/malta_defconfig:62:warning: symbol value 'm' invalid for NF_CT_PROTO_DCCP
arch/mips/configs/malta_defconfig:63:warning: symbol value 'm' invalid for NF_CT_PROTO_UDPLITE
arch/mips/configs/ip22_defconfig:70:warning: symbol value 'm' invalid for NF_CT_PROTO_DCCP
arch/mips/configs/ip22_defconfig:71:warning: symbol value 'm' invalid for NF_CT_PROTO_UDPLITE
This changes all the MIPS defconfigs with these symbols to have them
built-in.
Fixes: 9b91c96c5d ("netfilter: conntrack: built-in support for UDPlite")
Fixes: c51d39010a ("netfilter: conntrack: built-in support for DCCP")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14999/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d6e910502 upstream.
An ancient gcc bug (first reported in 2003) has apparently resurfaced
on MIPS, where kernelci.org reports an overly large stack frame in the
whirlpool hash algorithm:
crypto/wp512.c:987:1: warning: the frame size of 1112 bytes is larger than 1024 bytes [-Wframe-larger-than=]
With some testing in different configurations, I'm seeing large
variations in stack frames size up to 1500 bytes for what should have
around 300 bytes at most. I also checked the reference implementation,
which is essentially the same code but also comes with some test and
benchmarking infrastructure.
It seems that recent compiler versions on at least arm, arm64 and powerpc
have a partial fix for this problem, but enabling "-fsched-pressure", but
even with that fix they suffer from the issue to a certain degree. Some
testing on arm64 shows that the time needed to hash a given amount of
data is roughly proportional to the stack frame size here, which makes
sense given that the wp512 implementation is doing lots of loads for
table lookups, and the problem with the overly large stack is a result
of doing a lot more loads and stores for spilled registers (as seen from
inspecting the object code).
Disabling -fschedule-insns consistently fixes the problem for wp512,
in my collection of cross-compilers, the results are consistently better
or identical when comparing the stack sizes in this function, though
some architectures (notable x86) have schedule-insns disabled by
default.
The four columns are:
default: -O2
press: -O2 -fsched-pressure
nopress: -O2 -fschedule-insns -fno-sched-pressure
nosched: -O2 -no-schedule-insns (disables sched-pressure)
default press nopress nosched
alpha-linux-gcc-4.9.3 1136 848 1136 176
am33_2.0-linux-gcc-4.9.3 2100 2076 2100 2104
arm-linux-gnueabi-gcc-4.9.3 848 848 1048 352
cris-linux-gcc-4.9.3 272 272 272 272
frv-linux-gcc-4.9.3 1128 1000 1128 280
hppa64-linux-gcc-4.9.3 1128 336 1128 184
hppa-linux-gcc-4.9.3 644 308 644 276
i386-linux-gcc-4.9.3 352 352 352 352
m32r-linux-gcc-4.9.3 720 656 720 268
microblaze-linux-gcc-4.9.3 1108 604 1108 256
mips64-linux-gcc-4.9.3 1328 592 1328 208
mips-linux-gcc-4.9.3 1096 624 1096 240
powerpc64-linux-gcc-4.9.3 1088 432 1088 160
powerpc-linux-gcc-4.9.3 1080 584 1080 224
s390-linux-gcc-4.9.3 456 456 624 360
sh3-linux-gcc-4.9.3 292 292 292 292
sparc64-linux-gcc-4.9.3 992 240 992 208
sparc-linux-gcc-4.9.3 680 592 680 312
x86_64-linux-gcc-4.9.3 224 240 272 224
xtensa-linux-gcc-4.9.3 1152 704 1152 304
aarch64-linux-gcc-7.0.0 224 224 1104 208
arm-linux-gnueabi-gcc-7.0.1 824 824 1048 352
mips-linux-gcc-7.0.0 1120 648 1120 272
x86_64-linux-gcc-7.0.1 240 240 304 240
arm-linux-gnueabi-gcc-4.4.7 840 392
arm-linux-gnueabi-gcc-4.5.4 784 728 784 320
arm-linux-gnueabi-gcc-4.6.4 736 728 736 304
arm-linux-gnueabi-gcc-4.7.4 944 784 944 352
arm-linux-gnueabi-gcc-4.8.5 464 464 760 352
arm-linux-gnueabi-gcc-4.9.3 848 848 1048 352
arm-linux-gnueabi-gcc-5.3.1 824 824 1064 336
arm-linux-gnueabi-gcc-6.1.1 808 808 1056 344
arm-linux-gnueabi-gcc-7.0.1 824 824 1048 352
Trying the same test for serpent-generic, the picture is a bit different,
and while -fno-schedule-insns is generally better here than the default,
-fsched-pressure wins overall, so I picked that instead.
default press nopress nosched
alpha-linux-gcc-4.9.3 1392 864 1392 960
am33_2.0-linux-gcc-4.9.3 536 524 536 528
arm-linux-gnueabi-gcc-4.9.3 552 552 776 536
cris-linux-gcc-4.9.3 528 528 528 528
frv-linux-gcc-4.9.3 536 400 536 504
hppa64-linux-gcc-4.9.3 524 208 524 480
hppa-linux-gcc-4.9.3 768 472 768 508
i386-linux-gcc-4.9.3 564 564 564 564
m32r-linux-gcc-4.9.3 712 576 712 532
microblaze-linux-gcc-4.9.3 724 392 724 512
mips64-linux-gcc-4.9.3 720 384 720 496
mips-linux-gcc-4.9.3 728 384 728 496
powerpc64-linux-gcc-4.9.3 704 304 704 480
powerpc-linux-gcc-4.9.3 704 296 704 480
s390-linux-gcc-4.9.3 560 560 592 536
sh3-linux-gcc-4.9.3 540 540 540 540
sparc64-linux-gcc-4.9.3 544 352 544 496
sparc-linux-gcc-4.9.3 544 344 544 496
x86_64-linux-gcc-4.9.3 528 536 576 528
xtensa-linux-gcc-4.9.3 752 544 752 544
aarch64-linux-gcc-7.0.0 432 432 656 480
arm-linux-gnueabi-gcc-7.0.1 616 616 808 536
mips-linux-gcc-7.0.0 720 464 720 488
x86_64-linux-gcc-7.0.1 536 528 600 536
arm-linux-gnueabi-gcc-4.4.7 592 440
arm-linux-gnueabi-gcc-4.5.4 776 448 776 544
arm-linux-gnueabi-gcc-4.6.4 776 448 776 544
arm-linux-gnueabi-gcc-4.7.4 768 448 768 544
arm-linux-gnueabi-gcc-4.8.5 488 488 776 544
arm-linux-gnueabi-gcc-4.9.3 552 552 776 536
arm-linux-gnueabi-gcc-5.3.1 552 552 776 536
arm-linux-gnueabi-gcc-6.1.1 560 560 776 536
arm-linux-gnueabi-gcc-7.0.1 616 616 808 536
I did not do any runtime tests with serpent, so it is possible that stack
frame size does not directly correlate with runtime performance here and
it actually makes things worse, but it's more likely to help here, and
the reduced stack frame size is probably enough reason to apply the patch,
especially given that the crypto code is often used in deep call chains.
Link: https://kernelci.org/build/id/58797d7559b5149efdf6c3a9/logs/
Link: http://www.larc.usp.br/~pbarreto/WhirlpoolPage.html
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=11488
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=79149
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e46565cf6 upstream.
A recent change claimed to fix an off-by-one error in the OOB-port
completion handler, but instead introduced such an error. This could
specifically led to modem-status changes going unnoticed, effectively
breaking TIOCMGET.
Note that the offending commit fixes a loop-condition underflow and is
marked for stable, but should not be backported without this fix.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: 2d38088921 ("USB: serial: digi_acceleport: fix OOB data sanity
check")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2d38088921 upstream.
Make sure to check for short transfers to avoid underflow in a loop
condition when parsing the receive buffer.
Also fix an off-by-one error in the incomplete sanity check which could
lead to invalid data being parsed.
Fixes: 8c209e6782 ("USB: make actual_length in struct urb field u32")
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca8d8e03b4 upstream.
The flag register is offset by 1 from the respective channel data
register. This patch fixes an off-by-one error when attempting to read a
channel flag register where the base address was not properly offset.
Fixes: 28e5d3bb03 ("iio: 104-quad-8: Add IIO support for the ACCES 104-QUAD-8")
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 68fd814a33 upstream.
We see reported stalls/lockups in quarantine_remove_cache() on machines
with large amounts of RAM. quarantine_remove_cache() needs to scan
whole quarantine in order to take out all objects belonging to the
cache. Quarantine is currently 1/32-th of RAM, e.g. on a machine with
256GB of memory that will be 8GB. Moreover quarantine scanning is a
walk over uncached linked list, which is slow.
Add cond_resched() after scanning of each non-empty batch of objects.
Batches are specifically kept of reasonable size for quarantine_put().
On a machine with 256GB of RAM we should have ~512 non-empty batches,
each with 16MB of objects.
Link: http://lkml.kernel.org/r/20170308154239.25440-1-dvyukov@google.com
Signed-off-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Greg Thelen <gthelen@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40e952f9d6 upstream.
mem_cgroup_free() indirectly calls wb_domain_exit() which is not
prepared to deal with a struct wb_domain object that hasn't executed
wb_domain_init(). For instance, the following warning message is
printed by lockdep if alloc_percpu() fails in mem_cgroup_alloc():
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 1 PID: 1950 Comm: mkdir Not tainted 4.10.0+ #151
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Call Trace:
dump_stack+0x67/0x99
register_lock_class+0x36d/0x540
__lock_acquire+0x7f/0x1a30
lock_acquire+0xcc/0x200
del_timer_sync+0x3c/0xc0
wb_domain_exit+0x14/0x20
mem_cgroup_free+0x14/0x40
mem_cgroup_css_alloc+0x3f9/0x620
cgroup_apply_control_enable+0x190/0x390
cgroup_mkdir+0x290/0x3d0
kernfs_iop_mkdir+0x58/0x80
vfs_mkdir+0x10e/0x1a0
SyS_mkdirat+0xa8/0xd0
SyS_mkdir+0x14/0x20
entry_SYSCALL_64_fastpath+0x18/0xad
Add __mem_cgroup_free() which skips wb_domain_exit(). This is used by
both mem_cgroup_free() and mem_cgroup_alloc() clean up.
Fixes: 0b8f73e104 ("mm: memcontrol: clean up alloc, online, offline, free functions")
Link: http://lkml.kernel.org/r/20170306192122.24262-1-tahsin@google.com
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ebb4a1b84 upstream.
The following test case triggers BUG() in munlock_vma_pages_range():
int main(int argc, char *argv[])
{
int fd;
system("mount -t tmpfs -o huge=always none /mnt");
fd = open("/mnt/test", O_CREAT | O_RDWR);
ftruncate(fd, 4UL << 20);
mmap(NULL, 4UL << 20, PROT_READ | PROT_WRITE,
MAP_SHARED | MAP_FIXED | MAP_LOCKED, fd, 0);
mmap(NULL, 4096, PROT_READ | PROT_WRITE,
MAP_SHARED | MAP_LOCKED, fd, 0);
munlockall();
return 0;
}
The second mmap() create PTE-mapping of the first huge page in file. It
makes kernel munlock the page as we never keep PTE-mapped page mlocked.
On munlockall() when we handle vma created by the first mmap(),
munlock_vma_page() returns page_mask == 0, as the page is not mlocked
anymore. On next iteration follow_page_mask() return tail page, but
page_mask is HPAGE_NR_PAGES - 1. It makes us skip to the first tail
page of the next huge page and step on
VM_BUG_ON_PAGE(PageMlocked(page)).
The fix is not use the page_mask from follow_page_mask() at all. It has
no use for us.
Link: http://lkml.kernel.org/r/20170302150252.34120-1-kirill.shutemov@linux.intel.com
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c4ea6e28d upstream.
Fengguang reported random corruptions from various locations on x86-32
after commits d2852a2240 ("arch: add ARCH_HAS_SET_MEMORY config") and
9d876e79df ("bpf: fix unlocking of jited image when module ronx not set")
that uses the former. While x86-32 doesn't have a JIT like x86_64, the
bpf_prog_lock_ro() and bpf_prog_unlock_ro() got enabled due to
ARCH_HAS_SET_MEMORY, whereas Fengguang's test kernel doesn't have module
support built in and therefore never had the DEBUG_SET_MODULE_RONX setting
enabled.
After investigating the crashes further, it turned out that using
set_memory_ro() and set_memory_rw() didn't have the desired effect, for
example, setting the pages as read-only on x86-32 would still let
probe_kernel_write() succeed without error. This behavior would manifest
itself in situations where the vmalloc'ed buffer was accessed prior to
set_memory_*() such as in case of bpf_prog_alloc(). In cases where it
wasn't, the page attribute changes seemed to have taken effect, leading to
the conclusion that a TLB invalidate didn't happen. Moreover, it turned out
that this issue reproduced with qemu in "-cpu kvm64" mode, but not for
"-cpu host". When the issue occurs, change_page_attr_set_clr() did trigger
a TLB flush as expected via __flush_tlb_all() through cpa_flush_range(),
though.
There are 3 variants for issuing a TLB flush: invpcid_flush_all() (depends
on CPU feature bits X86_FEATURE_INVPCID, X86_FEATURE_PGE), cr4 based flush
(depends on X86_FEATURE_PGE), and cr3 based flush. For "-cpu host" case in
my setup, the flush used invpcid_flush_all() variant, whereas for "-cpu
kvm64", the flush was cr4 based. Switching the kvm64 case to cr3 manually
worked fine, and further investigating the cr4 one turned out that
X86_CR4_PGE bit was not set in cr4 register, meaning the
__native_flush_tlb_global_irq_disabled() wrote cr4 twice with the same
value instead of clearing X86_CR4_PGE in the first write to trigger the
flush.
It turned out that X86_CR4_PGE was cleared from cr4 during init from
lguest_arch_host_init() via adjust_pge(). The X86_FEATURE_PGE bit is also
cleared from there due to concerns of using PGE in guest kernel that can
lead to hard to trace bugs (see bff672e630 ("lguest: documentation V:
Host") in init()). The CPU feature bits are cleared in dynamic
boot_cpu_data, but they never propagated to __flush_tlb_all() as it uses
static_cpu_has() instead of boot_cpu_has() for testing which variant of TLB
flushing to use, meaning they still used the old setting of the host
kernel.
Clearing via setup_clear_cpu_cap(X86_FEATURE_PGE) so this would propagate
to static_cpu_has() checks is too late at this point as sections have been
patched already, so for now, it seems reasonable to switch back to
boot_cpu_has(X86_FEATURE_PGE) as it was prior to commit c109bf9599
("x86/cpufeature: Remove cpu_has_pge"). This lets the TLB flush trigger via
cr3 as originally intended, properly makes the new page attributes visible
and thus fixes the crashes seen by Fengguang.
Fixes: c109bf9599 ("x86/cpufeature: Remove cpu_has_pge")
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: bp@suse.de
Cc: Kees Cook <keescook@chromium.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: lkp@01.org
Cc: Laura Abbott <labbott@redhat.com>
Link: http://lkml.kernrl.org/r/20170301125426.l4nf65rx4wahohyl@wfg-t540p.sh.intel.com
Link: http://lkml.kernel.org/r/25c41ad9eca164be4db9ad84f768965b7eb19d9e.1489191673.git.daniel@iogearbox.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d24cdcd3e4 upstream.
I ran into this compile warning, which is the result of BUG_ON(1)
not always leading to the compiler treating the code path as
unreachable:
include/linux/ceph/osdmap.h: In function 'ceph_can_shift_osds':
include/linux/ceph/osdmap.h:62:1: error: control reaches end of non-void function [-Werror=return-type]
Using BUG() here avoids the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9ad86e42d upstream.
Having "ret" be a bool type works for everything except
ret = funcs->atomic_check(). The other functions all return zero on
error but ->atomic_check() returns negative error codes. We want to
propagate the error code but instead we return 1.
I found this bug with static analysis and I don't know if it affects
run time.
Fixes: 4cd4df8080 ("drm/atomic: Add ->atomic_check() to encoder helpers")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170207234601.GA23981@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc12bccda8 upstream.
Commit deb65870b5 ("drm/imx: imx-tve: check the value returned by
regulator_set_voltage()") exposes the following probe issue:
63ff0000.tve supply dac not found, using dummy regulator
imx-drm display-subsystem: failed to bind 63ff0000.tve (ops imx_tve_ops): -22
When the 'dac-supply' is not passed in the device tree a dummy regulator is
used and setting its voltage is not allowed.
To fix this issue, do not set the dac-supply voltage inside the driver
and let its voltage be specified in the device tree.
Print a warning if the the 'dac-supply' voltage has a value different
from 2.75V.
Fixes: deb65870b5 ("drm/imx: imx-tve: check the value returned by regulator_set_voltage()")
Suggested-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 31788ca803 upstream.
vmware tools has a daemon that gets layout information from the GUI and
forwards it to DRM so that the modesetting code can set preferred connector
locations and modes. This daemon was using control nodes but since control
nodes were just removed, make it possible for the daemon to use render- or
primary nodes instead. This is a bit ugly but will allow drm to proceed with
removal of the mostly unused control-node code and allow vmware to proceed
with fixing up automatic layout settings for gnome-shell/wayland.
We bump minor to inform user-space about the api change.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170221104227.2854-1-thellstrom@vmware.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 239ac65fa5 upstream.
The current caching state may not be tt_cached, even though the
placement contains TTM_PL_FLAG_CACHED, because placement can contain
multiple caching flags. Trying to swap out such a BO would trip up the
BUG_ON(ttm->caching_state != tt_cached);
in ttm_tt_swapout.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Christian König <christian.koenig@amd.com>.
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a882f5de40 upstream.
The vfct table can contain multiple vbios images if the
platform contains multiple GPUs. Noticed by netkas on
phoronix forums. This patch fixes those platforms.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 71f677a910 upstream.
The ast driver configures a window to enable access into BMC
memory space in order to read some configuration registers.
If this window is disabled, which it can be from the BMC side,
the ast driver can't function.
Closing this window is a necessity for security if a machine's
host side and BMC side are controlled by different parties;
i.e. a cloud provider offering machines "bare metal".
A recent patch went in to try to check if that window is open
but it does so by trying to access the registers in question
and testing if the result is 0xffffffff.
This method will trigger a PCIe error when the window is closed
which on some systems will be fatal (it will trigger an EEH
for example on POWER which will take out the device).
This patch improves this in two ways:
- First, if the firmware has put properties in the device-tree
containing the relevant configuration information, we use these.
- Otherwise, a bit in one of the SCU scratch registers (which
are readable via the VGA register space and writeable by the BMC)
will indicate if the BMC has closed the window. This bit has been
defined by Y.C Chen from Aspeed.
If the window is closed and the configuration isn't available from
the device-tree, some sane defaults are used. Those defaults are
hopefully sufficient for standard video modes used on a server.
Signed-off-by: Russell Currey <ruscur@russell.cc>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 19d19e9605 upstream.
When I originally introduced using the driver-indicated station as an
optimisation to avoid the hashtable lookup/iteration, of course it
wasn't intended to really functionally change anything.
I neglected, however, to take into account VLAN interfaces, which have
the property that management and data frames are handled differently:
data frames go directly to the station and the VLAN while management
frames continue to be processed over the underlying/associated AP-type
interface. As a consequence, when a driver used this optimisation for
management frames and the user enabled VLANs, my change broke things
since any management frames, particularly disassoc/deauth, were missed
by hostapd.
Fix this by restoring the original code path for non-data frames, they
aren't critical for performance to begin with.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=194713.
Big thanks goes to Jarek who bisected the issue and provided a very
detailed bug report, including the crucial information that he was
using VLANs in his configuration.
Fixes: 771e846bea9e ("mac80211: allow passing transmitter station on RX")
Reported-and-tested-by: Jarek Kamiński <jarek@freeside.be>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 890030d3c4 upstream.
When running a BA session, the driver (or the hardware) already takes
care of retransmitting failed frames, since it has to keep the receiver
reorder window in sync.
Adding another layer of retransmit around that does not improve
anything. In fact, it can only lead to some strong reordering with huge
latency.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b7540d8f25 upstream.
When RX aggregation starts, transmitter may continue send frames
with SN smaller than SSN until the AddBA response is received.
However, the reorder buffer is already initialized at this point,
which will cause the drop of such frames as duplicates since the
head SN of the reorder buffer is set to the SSN, which is bigger.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a9e9200d86 upstream.
The issue was found when entering suspend and resume.
It triggers a warning in:
mac80211/key.c: ieee80211_enable_keys()
...
WARN_ON_ONCE(sdata->crypto_tx_tailroom_needed_cnt ||
sdata->crypto_tx_tailroom_pending_dec);
...
It points out sdata->crypto_tx_tailroom_pending_dec isn't cleaned up successfully
in a delayed_work during suspend. Add a flush_delayed_work to fix it.
Signed-off-by: Matt Chen <matt.chen@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 86ef58a4e3 upstream.
The interleave-set cookie is a sum that sanity checks the composition of
an interleave set has not changed from when the namespace was initially
created. The checksum is calculated by sorting the DIMMs by their
location in the interleave-set. The comparison for the sort must be
64-bit wide, not byte-by-byte as performed by memcmp() in the broken
case.
Fix the implementation to accept correct cookie values in addition to
the Linux "memcmp" order cookies, but only allow correct cookies to be
generated going forward. It does mean that namespaces created by
third-party-tooling, or created by newer kernels with this fix, will not
validate on older kernels. However, there are a couple mitigating
conditions:
1/ platforms with namespace-label capable NVDIMMs are not widely
available.
2/ interleave-sets with a single-dimm are by definition not affected
(nothing to sort). This covers the QEMU-KVM NVDIMM emulation case.
The cookie stored in the namespace label will be fixed by any write the
namespace label, the most straightforward way to achieve this is to
write to the "alt_name" attribute of a namespace in sysfs.
Fixes: eaf961536e ("libnvdimm, nfit: add interleave-set state-tracking infrastructure")
Reported-by: Nicholas Moulin <nicholas.w.moulin@linux.intel.com>
Tested-by: Nicholas Moulin <nicholas.w.moulin@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4ab18701c6 upstream.
FDT tag parsing is not related to whether BLK_DEV_INITRD is configured
or not, move it out of the corresponding #ifdef/#endif block.
This fixes passing external FDT to the kernel configured w/o
BLK_DEV_INITRD support.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d254a340e upstream.
When first implementing support for changing the output frequency, an
optimization was added to continue the PWM after changing the prescaler
without having to reprogram the ON and OFF registers for the duty cycle,
in case the duty cycle stayed the same. This was flawed, because we
compared the absolute value of the duty cycle in nanoseconds instead of
the ratio to the period.
Fix the problem by removing the shortcut.
Fixes: 01ec847200 ("pwm-pca9685: Support changing the output frequency")
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0c424971f upstream.
In PowerNV PCI hotplug driver, the initial PCI slot's state is set
to PNV_PHP_STATE_POPULATED if no PCI devices are connected to the
slot. The PCI devices that are hot added to the slot won't be probed
and populated because of the check in pnv_php_enable():
/* Check if the slot has been configured */
if (php_slot->state != PNV_PHP_STATE_REGISTERED)
return 0;
This fixes the issue by leaving the slot in PNV_PHP_STATE_REGISTERED
state initially if nothing is connected to the slot.
Fixes: 360aebd85a ("drivers/pci/hotplug: Support surprise hotplug in powernv driver")
Reported-by: Hank Chang <hankmax0000@gmail.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Tested-by: Willie Liauw <williel@supermicro.com.tw>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d7d55536c6 upstream.
The surprise hotplug is driven by interrupt in PowerNV PCI hotplug
driver. In the interrupt handler, pnv_php_interrupt(), we bail when
pnv_pci_get_presence_state() returns zero wrongly. It causes the
presence change event is always ignored incorrectly.
This fixes the issue by bailing on error (non-zero value) returned
from pnv_pci_get_presence_state().
Fixes: 360aebd85a ("drivers/pci/hotplug: Support surprise hotplug in powernv driver")
Reported-by: Hank Chang <hankmax0000@gmail.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Tested-by: Willie Liauw <williel@supermicro.com.tw>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd4e2d2907 upstream.
When transport_clear_lun_ref() is shutting down a se_lun via
configfs with new I/O in-flight, it's possible to trigger a
NULL pointer dereference in transport_lookup_cmd_lun() due
to the fact percpu_ref_get() doesn't do any __PERCPU_REF_DEAD
checking before incrementing lun->lun_ref.count after
lun->lun_ref has switched to atomic_t mode.
This results in a NULL pointer dereference as LUN shutdown
code in core_tpg_remove_lun() continues running after the
existing ->release() -> core_tpg_lun_ref_release() callback
completes, and clears the RCU protected se_lun->lun_se_dev
pointer.
During the OOPs, the state of lun->lun_ref in the process
which triggered the NULL pointer dereference looks like
the following on v4.1.y stable code:
struct se_lun {
lun_link_magic = 4294932337,
lun_status = TRANSPORT_LUN_STATUS_FREE,
.....
lun_se_dev = 0x0,
lun_sep = 0x0,
.....
lun_ref = {
count = {
counter = 1
},
percpu_count_ptr = 3,
release = 0xffffffffa02fa1e0 <core_tpg_lun_ref_release>,
confirm_switch = 0x0,
force_atomic = false,
rcu = {
next = 0xffff88154fa1a5d0,
func = 0xffffffff8137c4c0 <percpu_ref_switch_to_atomic_rcu>
}
}
}
To address this bug, use percpu_ref_tryget_live() to ensure
once __PERCPU_REF_DEAD is visable on all CPUs and ->lun_ref
has switched to atomic_t, all new I/Os will fail to obtain
a new lun->lun_ref reference.
Also use an explicit percpu_ref_kill_and_confirm() callback
to block on ->lun_ref_comp to allow the first stage and
associated RCU grace period to complete, and then block on
->lun_ref_shutdown waiting for the final percpu_ref_put()
to drop the last reference via transport_lun_remove_cmd()
before continuing with core_tpg_remove_lun() shutdown.
Reported-by: Rob Millner <rlm@daterainc.com>
Tested-by: Rob Millner <rlm@daterainc.com>
Cc: Rob Millner <rlm@daterainc.com>
Tested-by: Vaibhav Tandon <vst@datera.io>
Cc: Vaibhav Tandon <vst@datera.io>
Tested-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 303529d6ef upstream.
The root port or PCIe switch downstream port might have been associated
with driver other than pnv-php. The MSI or MSIx might also have been
enabled by that driver (e.g. pcieport_drv). Attempt to enable MSI incurs
below backtrace:
PowerPC PowerNV PCI Hotplug Driver version: 0.1
------------[ cut here ]------------
WARNING: CPU: 19 PID: 1004 at drivers/pci/msi.c:1071 \
__pci_enable_msi_range+0x84/0x4e0
NIP [c000000000665c34] __pci_enable_msi_range+0x84/0x4e0
LR [c000000000665c24] __pci_enable_msi_range+0x74/0x4e0
Call Trace:
[c000000384d67600] [c000000000665c24] __pci_enable_msi_range+0x74/0x4e0
[c000000384d676e0] [d00000000aa31b04] pnv_php_register+0x564/0x5a0 [pnv_php]
[c000000384d677c0] [d00000000aa31658] pnv_php_register+0xb8/0x5a0 [pnv_php]
[c000000384d678a0] [d00000000aa31658] pnv_php_register+0xb8/0x5a0 [pnv_php]
[c000000384d67980] [d00000000aa31dfc] pnv_php_init+0x60/0x98 [pnv_php]
[c000000384d679f0] [c00000000000cfdc] do_one_initcall+0x6c/0x1d0
[c000000384d67ab0] [c000000000b92354] do_init_module+0x94/0x254
[c000000384d67b40] [c00000000019719c] load_module+0x258c/0x2c60
[c000000384d67d30] [c000000000197bb0] SyS_finit_module+0xf0/0x170
[c000000384d67e30] [c00000000000b184] system_call+0x38/0xe0
This fixes the issue by skipping enabling the surprise hotplug
capability if the MSI or MSIx on the PCI slot's upstream port has
been enabled by other driver.
Fixes: 360aebd85a ("drivers/pci/hotplug: Support surprise hotplug in powernv driver")
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Tested-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 32677207dc upstream.
The child_exit errno needs to be shifted by 8 bits to compare against the
return values for the bisect variables.
Fixes: c5dacb88f0 ("ktest: Allow overriding bisect test results")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee19428950 upstream.
at91sam9_ebi_get_config() is incorrectly converting timings in clock
cycles into timings in nanoseconds by multiplying the cycle values by
the clk rate instead of the clk period.
at91sam9_ebi_xslate_config() has the same problem for the
tdf_ns -> tdf_cycles conversion.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Chris Leahy <leahycm@gmail.com>
Fixes: 6a4ec4cd08 ("memory: add Atmel EBI (External Bus Interface) driver")
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 76b42abbf7 upstream.
If we have a file with an implicit hole (NO_HOLES feature enabled) that
has an extent following the hole, delayed writes against regions of the
file behind the hole happened before but were not yet flushed and then
we truncate the file to a smaller size that lies inside the hole, we
end up persisting a wrong disk_i_size value for our inode that leads to
data loss after umounting and mounting again the filesystem or after
the inode is evicted and loaded again.
This happens because at inode.c:btrfs_truncate_inode_items() we end up
setting last_size to the offset of the extent that we deleted and that
followed the hole. We then pass that value to btrfs_ordered_update_i_size()
which updates the inode's disk_i_size to a value smaller then the offset
of the buffered (delayed) writes.
Example reproducer:
$ mkfs.btrfs -f /dev/sdb
$ mount /dev/sdb /mnt
$ xfs_io -f -c "pwrite -S 0x01 0K 32K" /mnt/foo
$ xfs_io -d -c "pwrite -S 0x02 -b 32K 64K 32K" /mnt/foo
$ xfs_io -c "truncate 60K" /mnt/foo
--> inode's disk_i_size updated to 0
$ md5sum /mnt/foo
3c5ca3c3ab42f4b04d7e7eb0b0d4d806 /mnt/foo
$ umount /dev/sdb
$ mount /dev/sdb /mnt
$ md5sum /mnt/foo
d41d8cd98f00b204e9800998ecf8427e /mnt/foo
--> Empty file, all data lost!
Fixes: 16e7549f04 ("Btrfs: incompatible format change to remove hole extents")
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 93faccbbfa upstream.
To support unprivileged users mounting filesystems two permission
checks have to be performed: a test to see if the user allowed to
create a mount in the mount namespace, and a test to see if
the user is allowed to access the specified filesystem.
The automount case is special in that mounting the original filesystem
grants permission to mount the sub-filesystems, to any user who
happens to stumble across the their mountpoint and satisfies the
ordinary filesystem permission checks.
Attempting to handle the automount case by using override_creds
almost works. It preserves the idea that permission to mount
the original filesystem is permission to mount the sub-filesystem.
Unfortunately using override_creds messes up the filesystems
ordinary permission checks.
Solve this by being explicit that a mount is a submount by introducing
vfs_submount, and using it where appropriate.
vfs_submount uses a new mount internal mount flags MS_SUBMOUNT, to let
sget and friends know that a mount is a submount so they can take appropriate
action.
sget and sget_userns are modified to not perform any permission checks
on submounts.
follow_automount is modified to stop using override_creds as that
has proven problemantic.
do_mount is modified to always remove the new MS_SUBMOUNT flag so
that we know userspace will never by able to specify it.
autofs4 is modified to stop using current_real_cred that was put in
there to handle the previous version of submount permission checking.
cifs is modified to pass the mountpoint all of the way down to vfs_submount.
debugfs is modified to pass the mountpoint all of the way down to
trace_automount by adding a new parameter. To make this change easier
a new typedef debugfs_automount_t is introduced to capture the type of
the debugfs automount function.
Fixes: 069d5ac9ae ("autofs: Fix automounts by using current_real_cred()->uid")
Fixes: aeaa4a79ff ("fs: Call d_automount with the filesystems creds")
Reviewed-by: Trond Myklebust <trond.myklebust@primarydata.com>
Reviewed-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0a6fdbdeb1 upstream.
Avoid that srp_process_rsp() overwrites the status information
in ch if the SRP target response timed out and processing of
another task management function has already started. Avoid that
issuing multiple task management functions concurrently triggers
list corruption. This patch prevents that the following stack
trace appears in the system log:
WARNING: CPU: 8 PID: 9269 at lib/list_debug.c:52 __list_del_entry_valid+0xbc/0xc0
list_del corruption. prev->next should be ffffc90004bb7b00, but was ffff8804052ecc68
CPU: 8 PID: 9269 Comm: sg_reset Tainted: G W 4.10.0-rc7-dbg+ #3
Call Trace:
dump_stack+0x68/0x93
__warn+0xc6/0xe0
warn_slowpath_fmt+0x4a/0x50
__list_del_entry_valid+0xbc/0xc0
wait_for_completion_timeout+0x12e/0x170
srp_send_tsk_mgmt+0x1ef/0x2d0 [ib_srp]
srp_reset_device+0x5b/0x110 [ib_srp]
scsi_ioctl_reset+0x1c7/0x290
scsi_ioctl+0x12a/0x420
sd_ioctl+0x9d/0x100
blkdev_ioctl+0x51e/0x9f0
block_ioctl+0x38/0x40
do_vfs_ioctl+0x8f/0x700
SyS_ioctl+0x3c/0x70
entry_SYSCALL_64_fastpath+0x18/0xad
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Israel Rukshin <israelr@mellanox.com>
Cc: Max Gurtovoy <maxg@mellanox.com>
Cc: Laurence Oberman <loberman@redhat.com>
Cc: Steve Feeley <Steve.Feeley@sandisk.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6cb72bc1b4 upstream.
After srp_process_rsp() returns there is a short time during which
the scsi_host_find_tag() call will return a pointer to the SCSI
command that is being completed. If during that time a duplicate
response is received, avoid that the following call stack appears:
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: srp_recv_done+0x450/0x6b0 [ib_srp]
Oops: 0000 [#1] SMP
CPU: 10 PID: 0 Comm: swapper/10 Not tainted 4.10.0-rc7-dbg+ #1
Call Trace:
<IRQ>
__ib_process_cq+0x4b/0xd0 [ib_core]
ib_poll_handler+0x1d/0x70 [ib_core]
irq_poll_softirq+0xba/0x120
__do_softirq+0xba/0x4c0
irq_exit+0xbe/0xd0
smp_apic_timer_interrupt+0x38/0x50
apic_timer_interrupt+0x90/0xa0
</IRQ>
RIP: srp_recv_done+0x450/0x6b0 [ib_srp] RSP: ffff88046f483e20
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Israel Rukshin <israelr@mellanox.com>
Cc: Max Gurtovoy <maxg@mellanox.com>
Cc: Laurence Oberman <loberman@redhat.com>
Cc: Steve Feeley <Steve.Feeley@sandisk.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0fd27a88c2 upstream.
When we initialize buffer to create SRQ in kernel,
the number of pages was less than actually used in
following mlx5_fill_page_array().
Fixes: e126ba97db ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b0841766a upstream.
When sending packet to destination that was not resolved yet
via path query, the driver keeps the skb and tries to re-send it
again when the path is resolved.
But when re-sending via dev_queue_xmit the kernel doesn't call
to dev_hard_header, so IPoIB needs to keep 20 bytes in the skb
and to put the destination address inside them.
In that way the dev_start_xmit will have the correct destination,
and the driver won't take the destination from the skb->data, while
nothing exists there, which causes to packet be be dropped.
The test flow is:
1. Run the SM on remote node,
2. Restart the driver.
4. Ping some destination,
3. Observe that first ICMP request will be dropped.
Fixes: fc791b6335 ("IB/ipoib: move back IB LL address into the hard header")
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Tested-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1064f874ab upstream.
Ever since mount propagation was introduced in cases where a mount in
propagated to parent mount mountpoint pair that is already in use the
code has placed the new mount behind the old mount in the mount hash
table.
This implementation detail is problematic as it allows creating
arbitrary length mount hash chains.
Furthermore it invalidates the constraint maintained elsewhere in the
mount code that a parent mount and a mountpoint pair will have exactly
one mount upon them. Making it hard to deal with and to talk about
this special case in the mount code.
Modify mount propagation to notice when there is already a mount at
the parent mount and mountpoint where a new mount is propagating to
and place that preexisting mount on top of the new mount.
Modify unmount propagation to notice when a mount that is being
unmounted has another mount on top of it (and no other children), and
to replace the unmounted mount with the mount on top of it.
Move the MNT_UMUONT test from __lookup_mnt_last into
__propagate_umount as that is the only call of __lookup_mnt_last where
MNT_UMOUNT may be set on any mount visible in the mount hash table.
These modifications allow:
- __lookup_mnt_last to be removed.
- attach_shadows to be renamed __attach_mnt and its shadow
handling to be removed.
- commit_tree to be simplified
- copy_tree to be simplified
The result is an easier to understand tree of mounts that does not
allow creation of arbitrary length hash chains in the mount hash table.
The result is also a very slight userspace visible difference in semantics.
The following two cases now behave identically, where before order
mattered:
case 1: (explicit user action)
B is a slave of A
mount something on A/a , it will propagate to B/a
and than mount something on B/a
case 2: (tucked mount)
B is a slave of A
mount something on B/a
and than mount something on A/a
Histroically umount A/a would fail in case 1 and succeed in case 2.
Now umount A/a succeeds in both configurations.
This very small change in semantics appears if anything to be a bug
fix to me and my survey of userspace leads me to believe that no programs
will notice or care of this subtle semantic change.
v2: Updated to mnt_change_mountpoint to not call dput or mntput
and instead to decrement the counts directly. It is guaranteed
that there will be other references when mnt_change_mountpoint is
called so this is safe.
v3: Moved put_mountpoint under mount_lock in attach_recursive_mnt
As the locking in fs/namespace.c changed between v2 and v3.
v4: Reworked the logic in propagate_mount_busy and __propagate_umount
that detects when a mount completely covers another mount.
v5: Removed unnecessary tests whose result is alwasy true in
find_topper and attach_recursive_mnt.
v6: Document the user space visible semantic difference.
Fixes: b90fa9ae8f ("[PATCH] shared mount handling: bind and rbind")
Tested-by: Andrei Vagin <avagin@virtuozzo.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e290cecdd upstream.
brcmf_sdio_fromevntchan() was being called on the the data frame
rather than the software header, causing some frames to be
mischaracterized as on the event channel rather than the data channel.
This fixes a major performance regression (due to dropped packets). With
this patch the download speed jumped from 1Mbit/s back up to 40MBit/s due
to the sheer amount of packets being incorrectly processed.
Fixes: c56caa9db8 ("brcmfmac: screening firmware event packet")
Signed-off-by: Gavin Li <git@thegavinli.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[kvalo@codeaurora.org: improve commit logs based on email discussion]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 171ed0fcd8 upstream.
Commit 14a3ae34bf ("cxl: Prevent read/write to AFU config space while AFU
not configured") introduced a rwsem to fix an invalid memory access that
occurred when someone attempts to access the config space of an AFU on a
vPHB whilst the AFU is deconfigured, such as during EEH recovery.
It turns out that it's possible to run into a nested locking issue when EEH
recovery fails and a full device hotplug is required.
cxl_pci_error_detected() deconfigures the AFU, taking a writer lock on
configured_rwsem. When EEH recovery fails, the EEH code calls
pci_hp_remove_devices() to remove the device, which in turn calls
cxl_remove() -> cxl_pci_remove_afu() -> pci_deconfigure_afu(), which tries
to grab the writer lock that's already held.
Standard rwsem semantics don't express what we really want to do here and
don't allow for nested locking. Fix this by replacing the rwsem with an
atomic_t which we can control more finely. Allow the AFU to be locked
multiple times so long as there are no readers.
Fixes: 14a3ae34bf ("cxl: Prevent read/write to AFU config space while AFU not configured")
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 14a3ae34bf upstream.
During EEH recovery, we deconfigure all AFUs whilst leaving the
corresponding vPHB and virtual PCI device in place.
If something attempts to interact with the AFU's PCI config space (e.g.
running lspci) after the AFU has been deconfigured and before it's
reconfigured, cxl_pcie_{read,write}_config() will read invalid values from
the deconfigured struct cxl_afu and proceed to Oops when they try to
dereference pointers that have been set to NULL during deconfiguration.
Add a rwsem to struct cxl_afu so we can prevent interaction with config
space while the AFU is deconfigured.
Reported-by: Pradipta Ghosh <pradghos@in.ibm.com>
Suggested-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 239a3b6636 upstream.
When TX descriptors are filled in, the buffer DMA address is split
between the tx_desc->buf_phys_addr field (high-order bits) and
tx_desc->packet_offset field (5 low-order bits).
However, when we re-calculate the DMA address from the TX descriptor in
mvpp2_txq_inc_put(), we do not take tx_desc->packet_offset into
account. This means that when the DMA address is not aligned on a 32
bytes boundary, we end up calling dma_unmap_single() with a DMA address
that was not the one returned by dma_map_single().
This inconsistency is detected by the kernel when DMA_API_DEBUG is
enabled. We fix this problem by properly calculating the DMA address in
mvpp2_txq_inc_put().
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4920e3cf77 upstream.
The current implementation of setup_randomness uses the stack address
and therefore the pointer to the SYSIB 3.2.2 block as input data
address. Furthermore the length of the input data is the number of
virtual-machine description blocks which is typically one.
This means that typically a single zero byte is fed to
add_device_randomness.
Fix both of these and use the address of the first virtual machine
description block as input data address and also use the correct
length.
Fixes: bcfcbb6bae ("s390: add system information as device randomness")
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit da8fd820f3 upstream.
Commit bcfcbb6bae ("s390: add system information as device
randomness") intended to add some virtual machine specific information
to the randomness pool.
Unfortunately it uses the page allocator before it is ready to use. In
result the page allocator always returns NULL and the setup_randomness
function never adds anything to the randomness pool.
To fix this use memblock_alloc and memblock_free instead.
Fixes: bcfcbb6bae ("s390: add system information as device randomness")
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8676caa4fb upstream.
The data stored by the STSI instruction can be up to a page in size
but the memblock_virt_alloc allocation for tl_info only specifies
16 bytes. The memory after the short allocation is overwritten
every time arch_update_cpu_topology is called.
Fixes: 8c91058022 "s390/numa: establish cpu to node mapping early"
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb94a687d9 upstream.
Return a sensible value if TASK_SIZE if called from a kernel thread.
This gets us around an issue with copy_mount_options that does a magic
size calculation "TASK_SIZE - (unsigned long)data" while in a kernel
thread and data pointing to kernel space.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a4a81d8eeb upstream.
In binutils/libbfd (bfd/elf.c) it is enforced that all s390 specific ELF
notes like e.g. NT_S390_PREFIX or NT_S390_CTRS have "LINUX" specified
as note name. Otherwise the notes are ignored.
For /proc/vmcore we currently use "CORE" for these notes.
Up to now this has not been a real problem because the dump analysis tool
"crash" does not check the note name. But it will break all programs that
use libbfd for processing ELF notes.
So fix this and use "LINUX" for all s390 specific notes to comply with
libbfd.
Reported-by: Philipp Rudo <prudo@linux.vnet.ibm.com>
Reviewed-by: Philipp Rudo <prudo@linux.vnet.ibm.com>
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a63f53e34d upstream.
Since commit dd22f551 "block: Change direct_access calling convention",
the device size calculation in dcssblk_direct_access() is off-by-one.
This results in bdev_direct_access() always returning -ENXIO because the
returned value is not page aligned.
Fix this by adding 1 to the dev_sz calculation.
Fixes: dd22f551 ("block: Change direct_access calling convention")
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1e4a382fdc upstream.
For devices with multiple input queues, tiqdio_call_inq_handlers()
iterates over all input queues and clears the device's DSCI
during each iteration. If the DSCI is re-armed during one
of the later iterations, we therefore do not scan the previous
queues again.
The re-arming also raises a new adapter interrupt. But its
handler does not trigger a rescan for the device, as the DSCI
has already been erroneously cleared.
This can result in queue stalls on devices with multiple
input queues.
Fix it by clearing the DSCI just once, prior to scanning the queues.
As the code is moved in front of the loop, we also need to access
the DSCI directly (ie irq->dsci) instead of going via each queue's
parent pointer to the same irq. This is not a functional change,
and a follow-up patch will clean up the other users.
In practice, this bug only affects CQ-enabled HiperSockets devices,
ie. devices with sysfs-attribute "hsuid" set. Setting a hsuid is
needed for AF_IUCV socket applications that use HiperSockets
communication.
Fixes: 104ea556ee ("qdio: support asynchronous delivery of storage blocks")
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7d5e41216 upstream.
Upon failing to acquire regulator supplies the qcom-ufs driver calls
kfree() on the devm allocated memory used to store the name of the
regulator, leading to devres corruption.
Rather than switching to using the appropriate free function the patch
acknowledge the fact that "name" is always a constant string and we
don't actually need to create a local copy of it, but rather just
reference the constant string.
Fixes: add78fc057 ("phy: qcom-ufs: Use devm sibling of kstrdup for regulator names")
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 96794e4ed4 upstream.
Guest segment selector is 16 bit field and guest segment base is natural
width field. Fix two incorrect invocations accordingly.
Without this patch, build fails when aggressive inlining is used with ICC.
Signed-off-by: Chao Peng <chao.p.peng@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e1e8a9624f upstream.
User controlled KVM guests do not support the dirty log, as they have
no single gmap that we can check for changes.
As they have no single gmap, kvm->arch.gmap is NULL and all further
referencing to it for dirty checking will result in a NULL
dereference.
Let's return -EINVAL if a caller tries to sync dirty logs for a
UCONTROL guest.
Fixes: 15f36eb ("KVM: s390: Add proper dirty bitmap support to S390 kvm.")
Signed-off-by: Janosch Frank <frankja@linux.vnet.ibm.com>
Reported-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c9c858e2f upstream.
The MKS Instruments SCOM-0800 and SCOM-0801 cards (originally by Tenta
Technologies) are 3U CompactPCI serial cards with 4 and 8 serial ports,
respectively. The first 4 ports are implemented by an OX16PCI954 chip,
and the second 4 ports are implemented by an OX16C954 chip on a local
bus, bridged by the second PCI function of the OX16PCI954. The ports
are jumper-selectable as RS-232 and RS-422/485, and the UARTs use a
non-standard oscillator frequency of 20 MHz (base_baud = 1250000).
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 82f2341c94 upstream.
Currently N_HDLC line discipline uses a self-made singly linked list for
data buffers and has n_hdlc.tbuf pointer for buffer retransmitting after
an error.
The commit be10eb7589
("tty: n_hdlc add buffer flushing") introduced racy access to n_hdlc.tbuf.
After tx error concurrent flush_tx_queue() and n_hdlc_send_frames() can put
one data buffer to tx_free_buf_list twice. That causes double free in
n_hdlc_release().
Let's use standard kernel linked list and get rid of n_hdlc.tbuf:
in case of tx error put current data buffer after the head of tx_buf_list.
Signed-off-by: Alexander Popov <alex.popov@linux.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d641df819d upstream.
add_to_page_cache_lru() can fails, so the actual pages to read
can be smaller than the initial size of osd request. We need to
update osd request size in that case.
Signed-off-by: Yan, Zheng <zyan@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ae2f5e5ed0 upstream.
Fix the following build error with binutils 2.25.
CC arch/mips/mm/sc-ip22.o
{standard input}: Assembler messages:
{standard input}:132: Error: number (0x9000000080000000) larger than 32 bits
{standard input}:159: Error: number (0x9000000080000000) larger than 32 bits
{standard input}:200: Error: number (0x9000000080000000) larger than 32 bits
scripts/Makefile.build:293: recipe for target 'arch/mips/mm/sc-ip22.o' failed
make[1]: *** [arch/mips/mm/sc-ip22.o] Error 1
MIPS has used .set mips3 to temporarily switch the assembler to 64 bit
mode in 64 bit kernels virtually forever. Binutils 2.25 broke this
behavious partially by happily accepting 64 bit instructions in .set mips3
mode but puking on 64 bit constants when generating 32 bit ELF. Binutils
2.26 restored the old behaviour again.
Fix build with binutils 2.25 by open coding the offending
dli $1, 0x9000000080000000
as
li $1, 0x9000
dsll $1, $1, 48
which is ugly be the only thing that will build on all binutils vintages.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a5544880af upstream.
While looking for early possible module loading failures I was
able to reproduce a memory leak possible with kmemleak. There
are a few rare ways to trigger a failure:
o we've run into a failure while processing kernel parameters
(parse_args() returns an error)
o mod_sysfs_setup() fails
o we're a live patch module and copy_module_elf() fails
Chances of running into this issue is really low.
kmemleak splat:
unreferenced object 0xffff9f2c4ada1b00 (size 32):
comm "kworker/u16:4", pid 82, jiffies 4294897636 (age 681.816s)
hex dump (first 32 bytes):
6d 65 6d 73 74 69 63 6b 30 00 00 00 00 00 00 00 memstick0.......
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<ffffffff8c6cfeba>] kmemleak_alloc+0x4a/0xa0
[<ffffffff8c200046>] __kmalloc_track_caller+0x126/0x230
[<ffffffff8c1bc581>] kstrdup+0x31/0x60
[<ffffffff8c1bc5d4>] kstrdup_const+0x24/0x30
[<ffffffff8c3c23aa>] kvasprintf_const+0x7a/0x90
[<ffffffff8c3b5481>] kobject_set_name_vargs+0x21/0x90
[<ffffffff8c4fbdd7>] dev_set_name+0x47/0x50
[<ffffffffc07819e5>] memstick_check+0x95/0x33c [memstick]
[<ffffffff8c09c893>] process_one_work+0x1f3/0x4b0
[<ffffffff8c09cb98>] worker_thread+0x48/0x4e0
[<ffffffff8c0a2b79>] kthread+0xc9/0xe0
[<ffffffff8c6dab5f>] ret_from_fork+0x1f/0x40
[<ffffffffffffffff>] 0xffffffffffffffff
Fixes: e180a6b775 ("param: fix charp parameters set via sysfs")
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Reviewed-by: Aaron Tomlin <atomlin@redhat.com>
Reviewed-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Jessica Yu <jeyu@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fda2d27db6 upstream.
We will set LPCR with correct value for radix during int. This make sure we
start with a sanitized value of LPCR. In case of kexec, cpus can have LPCR
value based on the previous translation mode we were running.
Fixes: fe036a0605 ("powerpc/64/kexec: Fix MMU cleanup on radix")
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c21a493a2b upstream.
Currently xmon data-breakpoint feature is broken.
Whenever there is a watchpoint match occurs, hw_breakpoint_handler will
be called by do_break via notifier chains mechanism. If watchpoint is
registered by xmon, hw_breakpoint_handler won't find any associated
perf_event and returns immediately with NOTIFY_STOP. Similarly, do_break
also returns without notifying to xmon.
Solve this by returning NOTIFY_DONE when hw_breakpoint_handler does not
find any perf_event associated with matched watchpoint, rather than
NOTIFY_STOP, which tells the core code to continue calling the other
breakpoint handlers including the xmon one.
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 16f906d66c upstream.
The MAX_SEND_SGES check introduced in commit 655fec6987
("xprtrdma: Use gathered Send for large inline messages") fails
for devices that have a small max_sge.
Instead of checking for a large fixed maximum number of SGEs,
check for a minimum small number. RPC-over-RDMA will switch to
using a Read chunk if an xdr_buf has more pages than can fit in
the device's max_sge limit. This is considerably better than
failing all together to mount the server.
This fix supports devices that have as few as three send SGEs
available.
Reported-by: Selvin Xavier <selvin.xavier@broadcom.com>
Reported-by: Devesh Sharma <devesh.sharma@broadcom.com>
Reported-by: Honggang Li <honli@redhat.com>
Reported-by: Ram Amrani <Ram.Amrani@cavium.com>
Fixes: 655fec6987 ("xprtrdma: Use gathered Send for large ...")
Tested-by: Honggang Li <honli@redhat.com>
Tested-by: Ram Amrani <Ram.Amrani@cavium.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c95a3c6b88 upstream.
Commit d5440e27d3 ("xprtrdma: Enable pad optimization") made the
Linux client omit XDR round-up padding in normal Read and Write
chunks so that the client doesn't have to register and invalidate
3-byte memory regions that contain no real data.
Unfortunately, my cheery 2014 assessment that this optimization "is
supported now by both Linux and Solaris servers" was premature.
We've found bugs in Solaris in this area since commit d5440e27d3
("xprtrdma: Enable pad optimization") was merged (SYMLINK is the
main offender).
So for maximum interoperability, I'm disabling this optimization
again. If a CM private message is exchanged when connecting, the
client recognizes that the server is Linux, and enables the
optimization for that connection.
Until now the Solaris server bugs did not impact common operations,
and were thus largely benign. Soon, less capable devices on Linux
NFS/RDMA clients will make use of Read chunks more often, and these
Solaris bugs will prevent interoperation in more cases.
Fixes: 677eb17e94 ("xprtrdma: Fix XDR tail buffer marshalling")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5f0afbea4 upstream.
Pad optimization is changed by echoing into
/proc/sys/sunrpc/rdma_pad_optimize. This is a global setting,
affecting all RPC-over-RDMA connections to all servers.
The marshaling code picks up that value and uses it for decisions
about how to construct each RPC-over-RDMA frame. Having it change
suddenly in mid-operation can result in unexpected failures. And
some servers a client mounts might need chunk round-up, while
others don't.
So instead, copy the pad_optimize setting into each connection's
rpcrdma_ia when the transport is created, and use the copy, which
can't change during the life of the connection, instead.
This also removes a hack: rpcrdma_convert_iovs was using
the remote-invalidation-expected flag to predict when it could leave
out Write chunk padding. This is because the Linux server handles
implicit XDR padding on Write chunks correctly, and only Linux
servers can set the connection's remote-invalidation-expected flag.
It's more sensible to use the pad optimization setting instead.
Fixes: 677eb17e94 ("xprtrdma: Fix XDR tail buffer marshalling")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 24abdf1be1 upstream.
When pad optimization is disabled, rpcrdma_convert_iovs still
does not add explicit XDR round-up padding to a Read chunk.
Commit 677eb17e94 ("xprtrdma: Fix XDR tail buffer marshalling")
incorrectly short-circuited the test for whether round-up padding
is needed that appears later in rpcrdma_convert_iovs.
However, if this is indeed a regular Read chunk (and not a
Position-Zero Read chunk), the tail iovec _always_ contains the
chunk's padding, and never anything else.
So, it's easy to just skip the tail when padding optimization is
enabled, and add the tail in a subsequent Read chunk segment, if
disabled.
Fixes: 677eb17e94 ("xprtrdma: Fix XDR tail buffer marshalling")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit adee40b265 upstream.
Commit 3d8cc00073 ("dmaengine: ipu: Consolidate duplicated irq handlers")
consolidated the two interrupts routines into one, but the remaining
interrupt routine only checks the status of the error interrupts, not the
normal interrupts.
This patch fixes that problem (tested on i.MX31 PDK board).
Fixes: 3d8cc00073 ("dmaengine: ipu: Consolidate duplicated irq handlers")
Cc: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 656441478e upstream.
The commit 7a65417216 ("mtd/ifc: Add support for IFC controller
version 2.0") added support for version 2.0 of the IFC controller.
The version 2.0 controller has the ECC status registers at a different
location to the previous versions.
Correct the fsl_ifc_nand structure so that the ECC status can be read
from the correct location for both version 1.0 and 2.0 of the controller.
Fixes: 7a65417216 ("mtd/ifc: Add support for IFC controller version 2.0")
Signed-off-by: Mark Marshall <mark.marshall@omicronenergy.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 03a9e24ef2 upstream.
Recently I receive a bug report that on Linux v3.0 based kerenl, hot add
disk to a md linear device causes kernel crash at linear_congested(). From
the crash image analysis, I find in linear_congested(), mddev->raid_disks
contains value N, but conf->disks[] only has N-1 pointers available. Then
a NULL pointer deference crashes the kernel.
There is a race between linear_add() and linear_congested(), RCU stuffs
used in these two functions cannot avoid the race. Since Linuv v4.0
RCU code is replaced by introducing mddev_suspend(). After checking the
upstream code, it seems linear_congested() is not called in
generic_make_request() code patch, so mddev_suspend() cannot provent it
from being called. The possible race still exists.
Here I explain how the race still exists in current code. For a machine
has many CPUs, on one CPU, linear_add() is called to add a hard disk to a
md linear device; at the same time on other CPU, linear_congested() is
called to detect whether this md linear device is congested before issuing
an I/O request onto it.
Now I use a possible code execution time sequence to demo how the possible
race happens,
seq linear_add() linear_congested()
0 conf=mddev->private
1 oldconf=mddev->private
2 mddev->raid_disks++
3 for (i=0; i<mddev->raid_disks;i++)
4 bdev_get_queue(conf->disks[i].rdev->bdev)
5 mddev->private=newconf
In linear_add() mddev->raid_disks is increased in time seq 2, and on
another CPU in linear_congested() the for-loop iterates conf->disks[i] by
the increased mddev->raid_disks in time seq 3,4. But conf with one more
element (which is a pointer to struct dev_info type) to conf->disks[] is
not updated yet, accessing its structure member in time seq 4 will cause a
NULL pointer deference fault.
To fix this race, there are 2 parts of modification in the patch,
1) Add 'int raid_disks' in struct linear_conf, as a copy of
mddev->raid_disks. It is initialized in linear_conf(), always being
consistent with pointers number of 'struct dev_info disks[]'. When
iterating conf->disks[] in linear_congested(), use conf->raid_disks to
replace mddev->raid_disks in the for-loop, then NULL pointer deference
will not happen again.
2) RCU stuffs are back again, and use kfree_rcu() in linear_add() to
free oldconf memory. Because oldconf may be referenced as mddev->private
in linear_congested(), kfree_rcu() makes sure that its memory will not
be released until no one uses it any more.
Also some code comments are added in this patch, to make this modification
to be easier understandable.
This patch can be applied for kernels since v4.0 after commit:
3be260cc18 ("md/linear: remove rcu protections in favour of
suspend/resume"). But this bug is reported on Linux v3.0 based kernel, for
people who maintain kernels before Linux v4.0, they need to do some back
back port to this patch.
Changelog:
- V3: add 'int raid_disks' in struct linear_conf, and use kfree_rcu() to
replace rcu_call() in linear_add().
- v2: add RCU stuffs by suggestion from Shaohua and Neil.
- v1: initial effort.
Signed-off-by: Coly Li <colyli@suse.de>
Cc: Shaohua Li <shli@fb.com>
Cc: Neil Brown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb61bb82cb upstream.
The RTC is clocked from either an internal, imprecise, oscillator or an
external one, which is usually much more accurate.
The difference perceived between the time elapsed and the time reported by
the RTC is in a 10% scale, which prevents the RTC from being useful at all.
Fortunately, the external oscillator is reported to be mandatory in the
Allwinner datasheet, so we can just switch to it.
Fixes: 9765d2d943 ("rtc: sun6i: Add sun6i RTC driver")
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7bb3a371d1 upstream.
The introduction of the multi-device feature partially broke the support
for zoned block devices. In the function f2fs_scan_devices, sbi->devs
allocation and initialization is skipped in the case of a single device
mount. This result in no device information structure being allocated
for the device. This is fine if the device is a regular device, but in
the case of a zoned block device, the device zone type array is not
initialized, which causes the function __f2fs_issue_discard_zone to fail
as get_blkz_type is unable to determine the zone type of a section.
Fix this by always allocating and initializing the sbi->devs device
information array even in the case of a single device if that device is
zoned. For this particular case, make sure to obtain a reference on the
single device so that the call to blkdev_put() in destroy_device_list
operates as expected.
Fixes: 3c62be17d4 ("f2fs: support multiple devices")
Signed-off-by: Masato Suzuki <masato.suzuki@wdc.com>
Acked-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b107f5b97 upstream.
If segs_per_sec is over 1 like under SMR, previously f2fs issues discard
commands redundantly on the same section, since we didn't move end position
for the previous discard command.
E.g.,
start end
| |
prefree_bitmap = [01111100111100]
And, after issue discard for this section,
end start
| |
prefree_bitmap = [01111100111100]
Select this section again by searching from (end + 1),
start end
| |
prefree_bitmap = [01111100111100]
Fixes: 36abef4e79 ("f2fs: introduce mode=lfs mount option")
Cc: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e93b986525 upstream.
For foreground gc, greedy algorithm should be adapted, which makes
this formula work well:
(2 * (100 / config.overprovision + 1) + 6)
But currently, we fg_gc have a prior to select bg_gc victim segments to gc
first, these victims are selected by cost-benefit algorithm, we can't guarantee
such segments have the small valid blocks, which may destroy the f2fs rule, on
the worstest case, would consume all the free segments.
This patch fix this by add a filter in check_bg_victims, if segment's has # of
valid blocks over overprovision ratio, skip such segments.
Signed-off-by: Hou Pengyang <houpengyang@huawei.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 88c5c13a50 upstream.
It turns out a stakable filesystem like sdcardfs in AOSP can trigger multiple
vfs_create() to lower filesystem. In that case, f2fs will add multiple dentries
having same name which breaks filesystem consistency.
Until upper layer fixes, let's work around by f2fs, which shows actually not
much performance regression.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ed92d8c137 upstream.
We're not taking into account that the space needed for the (variable
length) attr bitmap, with the result that we'd sometimes get a spurious
ERANGE when the ACL data got close to the end of a page.
Just add in an extra page to make sure.
Signed-off-by: Weston Andros Adamson <dros@primarydata.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6682c14bbe upstream.
Bitmap and attrlen follow immediately after the op reply header. This
was an oversight from commit bf118a342f.
Consequences of this are just minor efficiency (extra calls to
xdr_shrink_bufhead).
Fixes: bf118a342f "NFSv4: include bitmap in nfsv4 get acl data"
Reviewed-by: Kinglong Mee <kinglongmee@gmail.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df3ab232e4 upstream.
If we see that our pNFS READ/WRITE/COMMIT operation failed, but we
also see that our layout segment is no longer valid, then we need to
get a new layout segment before retrying.
Fixes: 90816d1dda ("NFSv4.1/flexfiles: Don't mark the entire deviceid...")
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9d8cacbf56 upstream.
Copy offload code needs to be hooked into the code for handling
NFS4ERR_BAD_STATEID by ensuring that we set the "stateid" field
in struct nfs4_exception.
Reported-by: Olga Kornievskaia <aglo@umich.edu>
Fixes: 2e72448b07 ("NFS: Add COPY nfs operation")
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a974deee47 upstream.
If we exit because the file access check failed, we currently
leak the struct nfs4_state. We need to attach it to the
open context before returning.
Fixes: 3efb972247 ("NFSv4: Refactor _nfs4_open_and_get_state..")
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 783112f740 upstream.
Both the NFS protocols and the Linux VFS use a setattr operation with a
bitmap of attributes to set to set various file attributes including the
file size and the uid/gid.
The Linux syscalls never mix size updates with unrelated updates like
the uid/gid, and some file systems like XFS and GFS2 rely on the fact
that truncates don't update random other attributes, and many other file
systems handle the case but do not update the other attributes in the
same transaction. NFSD on the other hand passes the attributes it gets
on the wire more or less directly through to the VFS, leading to updates
the file systems don't expect. XFS at least has an assert on the
allowed attributes, which caught an unusual NFS client setting the size
and group at the same time.
To handle this issue properly this splits the notify_change call in
nfsd_setattr into two separate ones.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9797484ba8 upstream.
Commit 050c3d52cc ("vme: make core
vme support explicitly non-modular") dropped the remove function
because it appeared as if it was for removal of the bus, which is
not supported.
However, vme_bus_remove() is called when a VME device is removed
from the bus and not when the bus is removed; as it calls the VME
device driver's cleanup function. Without this function, the
remove() in the VME device driver is never called and VME device
drivers cannot be reloaded again.
Here we restore the remove function that was deleted in that
commit, and the reference to the function in the bus structure.
Fixes: 050c3d52cc ("vme: make core vme support explicitly non-modular")
Cc: Manohar Vanga <manohar.vanga@gmail.com>
Acked-by: Martyn Welch <martyn@welchs.me.uk>
Cc: devel@driverdev.osuosl.org
Signed-off-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6773386f97 upstream.
Kernels built with CONFIG_KASAN=y report the following BUG for rtl8192cu
and rtl8192c-common:
==================================================================
BUG: KASAN: slab-out-of-bounds in rtl92c_dm_bt_coexist+0x858/0x1e40
[rtl8192c_common] at addr ffff8801c90edb08
Read of size 1 by task kworker/0:1/38
page:ffffea0007243800 count:1 mapcount:0 mapping: (null)
index:0x0 compound_mapcount: 0
flags: 0x8000000000004000(head)
page dumped because: kasan: bad access detected
CPU: 0 PID: 38 Comm: kworker/0:1 Not tainted 4.9.7-gentoo #3
Hardware name: Gigabyte Technology Co., Ltd. To be filled by
O.E.M./Z77-DS3H, BIOS F11a 11/13/2013
Workqueue: rtl92c_usb rtl_watchdog_wq_callback [rtlwifi]
0000000000000000 ffffffff829eea33 ffff8801d7f0fa30 ffff8801c90edb08
ffffffff824c0f09 ffff8801d4abee80 0000000000000004 0000000000000297
ffffffffc070b57c ffff8801c7aa7c48 ffff880100000004 ffffffff000003e8
Call Trace:
[<ffffffff829eea33>] ? dump_stack+0x5c/0x79
[<ffffffff824c0f09>] ? kasan_report_error+0x4b9/0x4e0
[<ffffffffc070b57c>] ? _usb_read_sync+0x15c/0x280 [rtl_usb]
[<ffffffff824c0f75>] ? __asan_report_load1_noabort+0x45/0x50
[<ffffffffc06d7a88>] ? rtl92c_dm_bt_coexist+0x858/0x1e40 [rtl8192c_common]
[<ffffffffc06d7a88>] ? rtl92c_dm_bt_coexist+0x858/0x1e40 [rtl8192c_common]
[<ffffffffc06d0cbe>] ? rtl92c_dm_rf_saving+0x96e/0x1330 [rtl8192c_common]
...
The problem is due to rtl8192ce and rtl8192cu sharing routines, and having
different layouts of struct rtl_pci_priv, which is used by rtl8192ce, and
struct rtl_usb_priv, which is used by rtl8192cu. The problem was resolved
by placing the struct bt_coexist_info at the head of each of those private
areas.
Reported-and-tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40b368af4b upstream.
The addresses of Wlan NIC registers are natural alignment, but some
drivers have bugs. These are evident on platforms that need natural
alignment to access registers. This change contains the following:
1. Function _rtl8821ae_dbi_read() is used to read one byte from DBI,
thus it should use rtl_read_byte().
2. Register 0x4C7 of 8192ee is single byte.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3e8b571a9a upstream.
The "fw" firmware object is passed from the remoteproc core and should
not be overwritten, as that results in leaked buffers and a double free
of the the last firmware object.
Fixes: 051fb70fd4 ("remoteproc: qcom: Driver for the self-authenticating Hexagon v5")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f38e5fb95a upstream.
We must hold the rcu read lock across looking up glocks and trying to
bump their refcount to prevent the glocks from being freed in between.
Signed-off-by: Andrew Price <anprice@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 55efcfcd77 upstream.
The RDMA core uses ib_pack() to convert from unpacked CPU structs
to on-the-wire bitpacked structs.
This process requires that 1 bit fields are declared as u8 in the
unpacked struct, otherwise the packing process does not read the
value properly and the packed result is wired to 0. Several
places wrongly used int.
Crucially this means the kernel has never, set reversible
correctly in the path record request. It has always asked for
irreversible paths even if the ULP requests otherwise.
When the kernel is used with a SM that supports this feature, it
completely breaks communication management if reversible paths are
not properly requested.
The only reason this ever worked is because opensm ignores the
reversible bit.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d77044d142 upstream.
VSS may use a char device to support the communication between
the user level daemon and the driver. When the VSS channel is rescinded
we need to make sure that the char device is fully cleaned up before
we can process a new VSS offer from the host. Implement this logic.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 20951c7535 upstream.
Fcopy may use a char device to support the communication between
the user level daemon and the driver. When the Fcopy channel is rescinded
we need to make sure that the char device is fully cleaned up before
we can process a new Fcopy offer from the host. Implement this logic.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5a66fecbf6 upstream.
KVP may use a char device to support the communication between
the user level daemon and the driver. When the KVP channel is rescinded
we need to make sure that the char device is fully cleaned up before
we can process a new KVP offer from the host. Implement this logic.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ccb61f8a99 upstream.
The host can rescind a channel that has been offered to the
guest and once the channel is rescinded, the host does not
respond to any requests on that channel. Deal with the case where
the guest may be blocked waiting for a response from the host.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7e97dd8b7 upstream.
After the channel is rescinded, the host does not read from the rescinded channel.
Fail writes to a channel that has already been rescinded. If we permit writes on a
rescinded channel, since the host will not respond we will have situations where
we will be unable to unload vmbus drivers that cannot have any outstanding requests
to the host at the point they are unoaded.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 56ef6718a1 upstream.
It may happen that secondary CPUs are still alive and resetting
hv_context.tsc_page will cause a consequent crash in read_hv_clock_tsc()
as we don't check for it being not NULL there. It is safe as we're not
freeing this page anyways.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c7630d350 upstream.
Initializing hv_context.percpu_list in hv_synic_alloc() helps to prevent a
crash in percpu_channel_enq() when not all CPUs were online during
initialization and it naturally belongs there.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 421b8f20d3 upstream.
It may happen that not all CPUs are online when we do hv_synic_alloc() and
in case more CPUs come online later we may try accessing these allocated
structures.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 749494b6bd upstream.
Since commit: ba1582f222 ("usb: gadget: f_hid: use alloc_ep_req()")
we cannot allocate any requests in bind() as we check if we should
align request buffer based on endpoint descriptor which is assigned
in set_alt().
Allocating request in bind() function causes a NULL pointer
dereference.
This commit moves allocation of IN request from bind() to set_alt()
to prevent this issue.
Fixes: ba1582f222 ("usb: gadget: f_hid: use alloc_ep_req()")
Tested-by: David Lechner <david@lechnology.com>
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 33e4c1a998 upstream.
As IN request has to be allocated in set_alt() and released in
disable() we cannot use mutex to protect it as we cannot sleep
in those funcitons. Let's replace this mutex with a spinlock.
Tested-by: David Lechner <david@lechnology.com>
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aa65d11aa0 upstream.
When we unlock our spinlock to copy data to user we may get
disabled by USB host and free the whole list of completed out
requests including the one from which we are copying the data
to user memory.
To prevent from this let's remove our working element from
the list and place it back only if there is sth left when we
finish with it.
Fixes: 99c5150058 ("usb: gadget: hidg: register OUT INT endpoint for SET_REPORT")
Tested-by: David Lechner <david@lechnology.com>
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 20d2ca955b upstream.
Requests for out endpoint are allocated in bind() function
but never released.
This commit ensures that all pending requests are released
when we disable out endpoint.
Fixes: 99c5150058 ("usb: gadget: hidg: register OUT INT endpoint for SET_REPORT")
Tested-by: David Lechner <david@lechnology.com>
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5528954a1a upstream.
Commit 304f7e5e1d ("usb: gadget: Refactor request completion")
removed check if req->req.complete is non-NULL, resulting in a NULL
pointer derefence and a kernel panic.
This patch adds an empty complete function instead of re-introducing
the req->req.complete check.
Fixes: 304f7e5e1d ("usb: gadget: Refactor request completion")
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8236800da1 upstream.
Since:
commit 855ed04a37 ("usb: gadget: udc-core: independent registration
of gadgets and gadget drivers")
if we load gadget module but there is no free udc available
then it will be stored on a pending gadgets list.
$ modprobe g_zero.ko
$ modprobe g_ether.ko
[] udc-core: couldn't find an available UDC - added [g_ether] to list
of pending drivers
We scan this list each time when new UDC appears in system.
But we can get a free UDC each time after gadget unbind.
This commit add scanning of that list directly after unbinding
gadget from udc.
Thanks to this, when we unload first gadget:
$ rmmod g_zero.ko
gadget which is pending is automatically
attached to that UDC (if name matches).
Fixes: 855ed04a37 ("usb: gadget: udc-core: independent registration of gadgets and gadget drivers")
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5de4e1ea9a upstream.
The commit 4ac53087d6 ("usb: xhci: plat: Create both
HCDs before adding them") move add hcd to the end of
probe, this cause hcc_params uninitiated, because xHCI
driver sets hcc_params in xhci_gen_setup() called from
usb_add_hcd().
This patch checks the Maximum Primary Stream Array Size
in the hcc_params register after add primary hcd.
Signed-off-by: William wu <william.wu@rock-chips.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Fixes: 4ac53087d6 ("usb: xhci: plat: Create both HCDs before adding them")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ffb80fc672 upstream.
At least macOS seems to be sending
ClearFeature(ENDPOINT_HALT) to endpoints which
aren't Halted. This makes DWC3's CLEARSTALL command
time out which causes several issues for the driver.
Instead, let's just return 0 and bail out early.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a994ce2d7e upstream.
DA8xx driver is registering and using the CPPI 3.0 DMA controller but
actually, the DA8xx has a CPPI 4.1 DMA controller.
Remove the CPPI 3.0 quirk and methods.
Fixes: f8e9f34f80 ("usb: musb: Fix up DMA related macros")
Fixes: 7f6283ed6f ("usb: musb: Set up function pointers for DMA")
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61cd1b4cd1 upstream.
ds2490 driver was doing USB transfers from / to buffers on a stack.
This is not permitted and made the driver non-working with vmapped stacks.
Since all these transfers are done under the same bus_mutex lock we can
simply use shared buffers in a device private structure for two most common
of them.
While we are at it, let's also fix a comparison between int and size_t in
ds9490r_search() which made the driver spin in this function if state
register get requests were failing.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d2ce4ea1a0 upstream.
Near the beginning of w1_attach_slave_device() we increment a w1 master
reference count.
Later, when we are going to exit this function without actually attaching
a slave device (due to failure of __w1_attach_slave_device()) we need to
decrement this reference count back.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Fixes: 9fcbbac5de ("w1: process w1 netlink commands in w1_process thread")
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c42631376 upstream.
The priv->cmd_msg_buffer is allocated in the probe function, but never
kfree()ed. This patch converts the kzalloc() to resource-managed
kzalloc.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c919a3069c upstream.
Fixes: 05ca527000 can: gs_usb: add ethtool set_phys_id callback to locate physical device
The gs_usb driver is performing USB transfers using buffers allocated on
the stack. This causes the driver to not function with vmapped stacks.
Instead, allocate memory for the transfer buffers.
Signed-off-by: Ethan Zonca <e@ethanzonca.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9cf6cdba58 upstream.
Fixes a regression triggered by a change in the layout of
struct iio_chan_spec, but the real bug is in the driver which assumed
a specific structure layout in the first place. Hint: the two bits were
not OR:ed together as implied by the indentation prior to this patch,
there was a comma between them, which accidentally moved the ..._SCALE
bit to the next structure field. That field was .info_mask_shared_by_type
before the _available attributes was added by commit 5123960007
("iio:core: add a callback to allow drivers to provide _available
attributes") and .info_mask_separate_available afterwards, and the
regression happened.
info_mask_shared_by_type is actually a better choice than the originally
intended info_mask_separate for the ..._SCALE bit since a constant is
returned from mpl3115_read_raw for the scale. Using
info_mask_shared_by_type also preserves the behavior from before the
regression and is therefore less likely to cause other interesting side
effects.
The above mentioned regression causes an unintended sysfs attibute to
show up that is not backed by code, in turn causing the following NULL
pointer defererence to happen on access.
Segmentation fault
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = ecc3c000
[00000000] *pgd=87f91831
Internal error: Oops: 80000007 [#1] SMP ARM
Modules linked in:
CPU: 1 PID: 1051 Comm: cat Not tainted 4.10.0-rc5-00009-gffd8858-dirty #3
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
task: ed54ec00 task.stack: ee2bc000
PC is at 0x0
LR is at iio_read_channel_info_avail+0x40/0x280
pc : [<00000000>] lr : [<c06fbc1c>] psr: a0070013
sp : ee2bdda8 ip : 00000000 fp : ee2bddf4
r10: c0a53c74 r9 : ed79f000 r8 : ee8d1018
r7 : 00001000 r6 : 00000fff r5 : ee8b9a00 r4 : ed79f000
r3 : ee2bddc4 r2 : ee2bddbc r1 : c0a86dcc r0 : ee8d1000
Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control: 10c5387d Table: 3cc3c04a DAC: 00000051
Process cat (pid: 1051, stack limit = 0xee2bc210)
Stack: (0xee2bdda8 to 0xee2be000)
dda0: ee2bddc0 00000002 c016d720 c016d394 ed54ec00 00000000
ddc0: 60070013 ed413780 00000001 edffd480 ee8b9a00 00000fff 00001000 ee8d1018
dde0: ed79f000 c0a53c74 ee2bde0c ee2bddf8 c0513c58 c06fbbe8 edffd480 edffd540
de00: ee2bde3c ee2bde10 c0293474 c0513c40 c02933e4 ee2bde60 00000001 ed413780
de20: 00000001 ed413780 00000000 edffd480 ee2bde4c ee2bde40 c0291d00 c02933f0
de40: ee2bde9c ee2bde50 c024679c c0291ce0 edffd4b0 b6e37000 00020000 ee2bdf78
de60: 00000000 00000000 ed54ec00 ed013200 00000817 c0a111fc edffd540 ed413780
de80: b6e37000 00020000 00020000 ee2bdf78 ee2bded4 ee2bdea0 c0292890 c0246604
dea0: c0117940 c016ba50 00000025 c0a111fc b6e37000 ed413780 ee2bdf78 00020000
dec0: ee2bc000 b6e37000 ee2bdf44 ee2bded8 c021d158 c0292770 c0117764 b6e36004
dee0: c0f0d7c4 ee2bdfb0 b6f89228 00021008 ee2bdfac ee2bdf00 c0101374 c0117770
df00: 00000000 00000000 ee2bc000 00000000 ee2bdf34 ee2bdf20 c016ba04 c0171080
df20: 00000000 00020000 ed413780 b6e37000 00000000 ee2bdf78 ee2bdf74 ee2bdf48
df40: c021e7a0 c021d130 c023e300 c023e280 ee2bdf74 00000000 00000000 ed413780
df60: ed413780 00020000 ee2bdfa4 ee2bdf78 c021e870 c021e71c 00000000 00000000
df80: 00020000 00020000 b6e37000 00000003 c0108084 00000000 00000000 ee2bdfa8
dfa0: c0107ee0 c021e838 00020000 00020000 00000003 b6e37000 00020000 0001a2b4
dfc0: 00020000 00020000 b6e37000 00000003 7fffe000 00000000 00000000 00020000
dfe0: 00000000 be98eb4c 0000c740 b6f1985c 60070010 00000003 00000000 00000000
Backtrace:
[<c06fbbdc>] (iio_read_channel_info_avail) from [<c0513c58>] (dev_attr_show+0x24/0x50)
r10:c0a53c74 r9:ed79f000 r8:ee8d1018 r7:00001000 r6:00000fff r5:ee8b9a00
r4:edffd480
[<c0513c34>] (dev_attr_show) from [<c0293474>] (sysfs_kf_seq_show+0x90/0x110)
r5:edffd540 r4:edffd480
[<c02933e4>] (sysfs_kf_seq_show) from [<c0291d00>] (kernfs_seq_show+0x2c/0x30)
r10:edffd480 r9:00000000 r8:ed413780 r7:00000001 r6:ed413780 r5:00000001
r4:ee2bde60 r3:c02933e4
[<c0291cd4>] (kernfs_seq_show) from [<c024679c>] (seq_read+0x1a4/0x4e0)
[<c02465f8>] (seq_read) from [<c0292890>] (kernfs_fop_read+0x12c/0x1cc)
r10:ee2bdf78 r9:00020000 r8:00020000 r7:b6e37000 r6:ed413780 r5:edffd540
r4:c0a111fc
[<c0292764>] (kernfs_fop_read) from [<c021d158>] (__vfs_read+0x34/0x118)
r10:b6e37000 r9:ee2bc000 r8:00020000 r7:ee2bdf78 r6:ed413780 r5:b6e37000
r4:c0a111fc
[<c021d124>] (__vfs_read) from [<c021e7a0>] (vfs_read+0x90/0x11c)
r8:ee2bdf78 r7:00000000 r6:b6e37000 r5:ed413780 r4:00020000
[<c021e710>] (vfs_read) from [<c021e870>] (SyS_read+0x44/0x90)
r8:00020000 r7:ed413780 r6:ed413780 r5:00000000 r4:00000000
[<c021e82c>] (SyS_read) from [<c0107ee0>] (ret_fast_syscall+0x0/0x1c)
r10:00000000 r8:c0108084 r7:00000003 r6:b6e37000 r5:00020000 r4:00020000
Code: bad PC value
---[ end trace 9c4938ccd0389004 ]---
Fixes: cc26ad455f ("iio: Add Freescale MPL3115A2 pressure / temperature sensor driver")
Fixes: 5123960007 ("iio:core: add a callback to allow drivers to provide _available attributes")
Reported-by: Ken Lin <ken.lin@advantech.com>
Tested-by: Ken Lin <ken.lin@advantech.com>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6a6e1d56a0 upstream.
Fixes a regression triggered by a change in the layout of
struct iio_chan_spec, but the real bug is in the driver which assumed
a specific structure layout in the first place. Hint: the three bits were
not OR:ed together as implied by the indentation prior to this patch,
there was a comma between the first two, which accidentally moved the
..._SCALE and ..._OFFSET bits to the next structure field. That field
was .info_mask_shared_by_type before the _available attributes was added
by commit 5123960007 ("iio:core: add a callback to allow drivers to
provide _available attributes") and .info_mask_separate_available
afterwards, and the regression happened.
info_mask_shared_by_type is actually a better choice than the originally
intended info_mask_separate for the ..._SCALE and ..._OFFSET bits since
a constant is returned from mpl115_read_raw for the scale/offset. Using
info_mask_shared_by_type also preserves the behavior from before the
regression and is therefore less likely to cause other interesting side
effects.
The above mentioned regression causes unintended sysfs attibutes to
show up that are not backed by code, in turn causing a NULL pointer
defererence to happen on access.
Fixes: 3017d90e89 ("iio: Add Freescale MPL115A2 pressure / temperature sensor driver")
Fixes: 5123960007 ("iio:core: add a callback to allow drivers to provide _available attributes")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d81bbe6d88 upstream.
This reverts commit 0bfc445dec.
When we change the permissions of regions mapped using contiguous
entries, the architecture requires us to follow a Break-Before-Make
strategy, breaking *all* associated entries before we can change any of
the following properties from the entries:
- presence of the contiguous bit
- output address
- attributes
- permissiones
Failure to do so can result in a number of problems (e.g. TLB conflict
aborts and/or erroneous results from TLB lookups).
See ARM DDI 0487A.k_iss10775, "Misprogramming of the Contiguous bit",
page D4-1762.
We do not take this into account when altering the permissions of kernel
segments in mark_rodata_ro(), where we change the permissions of live
contiguous entires one-by-one, leaving them transiently inconsistent.
This has been observed to result in failures on some fast model
configurations.
Unfortunately, we cannot follow Break-Before-Make here as we'd have to
unmap kernel text and data used to perform the sequence.
For the timebeing, revert commit 0bfc445dec so as to avoid issues
resulting from this misuse of the contiguous bit.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reported-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <Will.Deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0bdbf3b071 upstream.
The IRQFD framework calls the architecture dependent function
twice if the corresponding GSI type is edge triggered. For ARM,
the function kvm_set_msi() is getting called twice whenever the
IRQFD receives the event signal. The rest of the code path is
trying to inject the MSI without any validation checks. No need
to call the function vgic_its_inject_msi() second time to avoid
an unnecessary overhead in IRQ queue logic. It also avoids the
possibility of VM seeing the MSI twice.
Simple fix, return -1 if the argument 'level' value is zero.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d0928f18b upstream.
Since it was introduced in commit da8d02d19f ("arm64/capabilities:
Make use of system wide safe value"), __raw_read_system_reg() has
erroneously mapped some sysreg IDs to other registers.
For the fields in ID_ISAR5_EL1, our local feature detection will be
erroneous. We may spuriously detect that a feature is uniformly
supported, or may fail to detect when it actually is, meaning some
compat hwcaps may be erroneous (or not enforced upon hotplug).
This patch corrects the erroneous entries.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Fixes: da8d02d19f ("arm64/capabilities: Make use of system wide safe value")
Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit adbe7e26f4 upstream.
When bypassing SWIOTLB on small-memory systems, we need to avoid calling
into swiotlb_dma_mapping_error() in exactly the same way as we avoid
swiotlb_dma_supported(), because the former also relies on SWIOTLB state
being initialised.
Under the assumptions for which we skip SWIOTLB, dma_map_{single,page}()
will only ever return the DMA-offset-adjusted physical address of the
page passed in, thus we can report success unconditionally.
Fixes: b67a8b29df ("arm64: mm: only initialize swiotlb when necessary")
CC: Jisheng Zhang <jszhang@marvell.com>
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f36ebaf21 upstream.
When we fault in a page, we flush it to the PoC (Point of Coherency)
if the faulting vcpu has its own caches off, so that it can observe
the page we just brought it.
But if the vcpu has its caches on, we skip that step. Bad things
happen when *another* vcpu tries to access that page with its own
caches disabled. At that point, there is no garantee that the
data has made it to the PoC, and we access stale data.
The obvious fix is to always flush to PoC when a page is faulted
in, no matter what the state of the vcpu is.
Fixes: 2d58b733c8 ("arm64: KVM: force cache clean on page fault when caches are off")
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 58ab9a088d upstream.
Kirill reported a warning from UBSAN about undefined behavior when using
protection keys. He is running on hardware that actually has support for
it, which is not widely available.
The warning triggers because of very large shifts of integers when doing a
pkey_free() of a large, invalid value. This happens because we never check
that the pkey "fits" into the mm_pkey_allocation_map().
I do not believe there is any danger here of anything bad happening
other than some aliasing issues where somebody could do:
pkey_free(35);
and the kernel would effectively execute:
pkey_free(8);
While this might be confusing to an app that was doing something stupid, it
has to do something stupid and the effects are limited to the app shooting
itself in the foot.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: linux-kselftest@vger.kernel.org
Cc: shuah@kernel.org
Cc: kirill.shutemov@linux.intel.com
Link: http://lkml.kernel.org/r/20170223222603.A022ED65@viggo.jf.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e38bea99a upstream.
fuse_file_put() was missing the "force" flag for the RELEASE request when
sending synchronously (fuseblk).
If this flag is not set, then a sync request may be interrupted before it
is dequeued by the userspace filesystem. In this case the OPEN won't be
balanced with a RELEASE.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Fixes: 5a18ec176c ("fuse: fix hang of single threaded fuseblk filesystem")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 89027579bc upstream.
When we're used as a fallback algorithm, we should propagate
the NEED_FALLBACK bit when searching for the underlying ECB mode.
This just happens to fix a hang too because otherwise the search
may end up loading the same module that triggered this XTS creation.
Fixes: f1c131b454 ("crypto: xts - Convert to skcipher")
Reported-by: Harald Freudenberger <freude@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c68bb0f62 upstream.
Running with KASAN and crypto tests currently gives
BUG: KASAN: global-out-of-bounds in __test_aead+0x9d9/0x2200 at addr ffffffff8212fca0
Read of size 16 by task cryptomgr_test/1107
Address belongs to variable 0xffffffff8212fca0
CPU: 0 PID: 1107 Comm: cryptomgr_test Not tainted 4.10.0+ #45
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.9.1-1.fc24 04/01/2014
Call Trace:
dump_stack+0x63/0x8a
kasan_report.part.1+0x4a7/0x4e0
? __test_aead+0x9d9/0x2200
? crypto_ccm_init_crypt+0x218/0x3c0 [ccm]
kasan_report+0x20/0x30
check_memory_region+0x13c/0x1a0
memcpy+0x23/0x50
__test_aead+0x9d9/0x2200
? kasan_unpoison_shadow+0x35/0x50
? alg_test_akcipher+0xf0/0xf0
? crypto_skcipher_init_tfm+0x2e3/0x310
? crypto_spawn_tfm2+0x37/0x60
? crypto_ccm_init_tfm+0xa9/0xd0 [ccm]
? crypto_aead_init_tfm+0x7b/0x90
? crypto_alloc_tfm+0xc4/0x190
test_aead+0x28/0xc0
alg_test_aead+0x54/0xd0
alg_test+0x1eb/0x3d0
? alg_find_test+0x90/0x90
? __sched_text_start+0x8/0x8
? __wake_up_common+0x70/0xb0
cryptomgr_test+0x4d/0x60
kthread+0x173/0x1c0
? crypto_acomp_scomp_free_ctx+0x60/0x60
? kthread_create_on_node+0xa0/0xa0
ret_from_fork+0x2c/0x40
Memory state around the buggy address:
ffffffff8212fb80: 00 00 00 00 01 fa fa fa fa fa fa fa 00 00 00 00
ffffffff8212fc00: 00 01 fa fa fa fa fa fa 00 00 00 00 01 fa fa fa
>ffffffff8212fc80: fa fa fa fa 00 05 fa fa fa fa fa fa 00 00 00 00
^
ffffffff8212fd00: 01 fa fa fa fa fa fa fa 00 00 00 00 01 fa fa fa
ffffffff8212fd80: fa fa fa fa 00 00 00 00 00 05 fa fa fa fa fa fa
This always happens on the same IV which is less than 16 bytes.
Per Ard,
"CCM IVs are 16 bytes, but due to the way they are constructed
internally, the final couple of bytes of input IV are dont-cares.
Apparently, we do read all 16 bytes, which triggers the KASAN errors."
Fix this by padding the IV with null bytes to be at least 16 bytes.
Fixes: 0bc5a6c5c7 ("crypto: testmgr - Disable rfc4309 test and convert test vectors")
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c0bb03924f upstream.
DoS protection conditions were altered in WS2016 and now it's easy to get
-EAGAIN returned from vmbus_post_msg() (e.g. when we try changing MTU on a
netvsc device in a loop). All vmbus_post_msg() callers don't retry the
operation and we usually end up with a non-functional device or crash.
While host's DoS protection conditions are unknown to me my tests show that
it can take up to 10 seconds before the message is sent so doing udelay()
is not an option, we really need to sleep. Almost all vmbus_post_msg()
callers are ready to sleep but there is one special case:
vmbus_initiate_unload() which can be called from interrupt/NMI context and
we can't sleep there. I'm also not sure about the lonely
vmbus_send_tl_connect_request() which has no in-tree users but its external
users are most likely waiting for the host to reply so sleeping there is
also appropriate.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a7275a3d8 upstream.
eb5767122f ("PCI: altera: Simplify TLB_CFG_DW0 usage") used
TLP_FMTTYPE_CFGRD* (instead of TLP_FMTTYPE_CFGWR*) for TLP writes, which
causes writing to configuration space to fail. Fix it by using correct
FMTTYPE for write operation.
Fixes: eb5767122f ("PCI: altera: Simplify TLB_CFG_DW0 usage")
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 49f4b08e61 upstream.
pnv_php_disable_irq() can be called in two paths: Bailing path in
pnv_php_enable_irq() or releasing slot. The MSI (or MSIx) interrupts
is disabled unconditionally in pnv_php_disable_irq(). It's wrong
because that might be enabled by drivers other than pnv-php.
This disables MSI (or MSIx) interrupts and the PCI device only if
it was enabled by pnv-php. In the error path of pnv_php_enable_irq(),
we rely on the newly added parameter @disable_device. In the path
of releasing slot, @pnv_php->irq is checked.
Fixes: 360aebd85a ("drivers/pci/hotplug: Support surprise hotplug in powernv driver")
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 60e2e2fbaf upstream.
The devfn of 00:02.0 is 0x10. devfn_to_wslot(0x10) == 0x2, and
wslot_to_devfn(0x2) should be 0x10, while it's 0x2 in the current code.
Due to this, hv_eject_device_work() -> pci_get_domain_bus_and_slot()
returns NULL and pci_stop_and_remove_bus_device() is not called.
Later when the real device driver's .remove() is invoked by
hv_pci_remove() -> pci_stop_root_bus(), some warnings can be noticed
because the VM has lost the access to the underlying device at that
time.
Signed-off-by: Jake Oshins <jakeo@microsoft.com>
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Haiyang Zhang <haiyangz@microsoft.com>
CC: K. Y. Srinivasan <kys@microsoft.com>
CC: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c9f1e32600 upstream.
This patch fixes the OTP register definitions for the AR934x and AR9550
WMAC SoC.
Previously, the ath9k driver was unable to initialize the integrated
WMAC on an Aerohive AP121:
| ath: phy0: timeout (1000 us) on reg 0x30018: 0xbadc0ffe & 0x00000007 != 0x00000004
| ath: phy0: timeout (1000 us) on reg 0x30018: 0xbadc0ffe & 0x00000007 != 0x00000004
| ath: phy0: Unable to initialize hardware; initialization status: -5
| ath9k ar934x_wmac: failed to initialize device
| ath9k: probe of ar934x_wmac failed with error -5
It turns out that the AR9300_OTP_STATUS and AR9300_OTP_DATA
definitions contain a typo.
Cc: Gabor Juhos <juhosg@openwrt.org>
Fixes: add295a4af "ath9k: use correct OTP register offsets for AR9550"
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a5e969bb2 upstream.
The code currently relies on refcounting to disable IRQs from within the
IRQ handler and re-enabling them again after the tasklet has run.
However, due to race conditions sometimes the IRQ handler might be
called twice, or the tasklet may not run at all (if interrupted in the
middle of a reset).
This can cause nasty imbalances in the irq-disable refcount which will
get the driver permanently stuck until the entire radio has been stopped
and started again (ath_reset will not recover from this).
Instead of using this fragile logic, change the code to ensure that
running the irq handler during tasklet processing is safe, and leave the
refcount untouched.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cb4281528b upstream.
Rx filter reset and the dynamic tx switch mode (EXT_RESOURCE_CFG)
configuration are causing the following errors when UTF firmware
is loaded to the target.
Error message 1:
[ 598.015629] ath10k_pci 0001:01:00.0: failed to ping firmware: -110
[ 598.020828] ath10k_pci 0001:01:00.0: failed to reset rx filter: -110
[ 598.141556] ath10k_pci 0001:01:00.0: failed to start core (testmode): -110
Error message 2:
[ 668.615839] ath10k_ahb a000000.wifi: failed to send ext resource cfg command : -95
[ 668.618902] ath10k_ahb a000000.wifi: failed to start core (testmode): -95
Avoiding these configurations while bringing the target in
testmode is solving the problem.
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cb97fbbcac upstream.
Parallel reads from multiple threads on a file descriptor
are not well defined and racy. It is safer to return to original
behavior and simply fail the additional read.
The solution is to remove request for next read credit.
Fixes: ff1586a7ea ("mei: enqueue consecutive reads")
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4753d8a24d upstream.
If the file system requires journal recovery, and the device is
read-ony, return EROFS to the mount system call. This allows xfstests
generic/050 to pass.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 97abd7d4b5 upstream.
If the journal is aborted, the needs_recovery feature flag should not
be removed. Otherwise, it's the journal might not get replayed and
this could lead to more data getting lost.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eb5efbcb76 upstream.
The write_end() function must always unlock the page and drop its ref
count, even on an error.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd01b690f8 upstream.
In the case where the child's encryption context was inconsistent with
its parent directory, we were using inode->i_sb and inode->i_ino after
the inode had already been iput(). Fix this by doing the iput() in the
correct places.
Note: only ext4 had this bug, not f2fs and ubifs.
Fixes: d9cdc90331 ("ext4 crypto: enforce context consistency")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3b136499e9 upstream.
ext4_journalled_write_end() did not propely handle all the cases when
generic_perform_write() did not copy all the data into the target page
and could mark buffers with uninitialized contents as uptodate and dirty
leading to possible data corruption (which would be quickly fixed by
generic_perform_write() retrying the write but still). Fix the problem
by carefully handling the case when the page that is written to is not
uptodate.
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd648b8a8f upstream.
If filesystem groups are artifically small (using parameter -g to
mkfs.ext4), ext4_mb_normalize_request() can result in a request that is
larger than a block group. Trim the request size to not confuse
allocation code.
Reported-by: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 03e916fa8b upstream.
Inside ext4_ext_shift_extents() function ext4_find_extent() is called
without EXT4_EX_NOCACHE flag, which should prevent cache population.
This leads to oudated offsets in the extents tree and wrong blocks
afterwards.
Patch fixes the problem providing EXT4_EX_NOCACHE flag for each
ext4_find_extents() call inside ext4_ext_shift_extents function.
Fixes: 331573febb
Signed-off-by: Roman Pen <roman.penyaev@profitbricks.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: Namjae Jeon <namjae.jeon@samsung.com>
Cc: Andreas Dilger <adilger.kernel@dilger.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a9b8cba62 upstream.
While doing 'insert range' start block should be also shifted right.
The bug can be easily reproduced by the following test:
ptr = malloc(4096);
assert(ptr);
fd = open("./ext4.file", O_CREAT | O_TRUNC | O_RDWR, 0600);
assert(fd >= 0);
rc = fallocate(fd, 0, 0, 8192);
assert(rc == 0);
for (i = 0; i < 2048; i++)
*((unsigned short *)ptr + i) = 0xbeef;
rc = pwrite(fd, ptr, 4096, 0);
assert(rc == 4096);
rc = pwrite(fd, ptr, 4096, 4096);
assert(rc == 4096);
for (block = 2; block < 1000; block++) {
rc = fallocate(fd, FALLOC_FL_INSERT_RANGE, 4096, 4096);
assert(rc == 0);
for (i = 0; i < 2048; i++)
*((unsigned short *)ptr + i) = block;
rc = pwrite(fd, ptr, 4096, 4096);
assert(rc == 4096);
}
Because start block is not included in the range the hole appears at
the wrong offset (just after the desired offset) and the following
pwrite() overwrites already existent block, keeping hole untouched.
Simple way to verify wrong behaviour is to check zeroed blocks after
the test:
$ hexdump ./ext4.file | grep '0000 0000'
The root cause of the bug is a wrong range (start, stop], where start
should be inclusive, i.e. [start, stop].
This patch fixes the problem by including start into the range. But
not to break left shift (range collapse) stop points to the beginning
of the a block, not to the end.
The other not obvious change is an iterator check on validness in a
main loop. Because iterator is unsigned the following corner case
should be considered with care: insert a block at 0 offset, when stop
variables overflows and never becomes less than start, which is 0.
To handle this special case iterator is set to NULL to indicate that
end of the loop is reached.
Fixes: 331573febb
Signed-off-by: Roman Pen <roman.penyaev@profitbricks.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: Namjae Jeon <namjae.jeon@samsung.com>
Cc: Andreas Dilger <adilger.kernel@dilger.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e02898b423 upstream.
loop_reread_partitions() needs to do I/O, but we just froze the queue,
so we end up waiting forever. This can easily be reproduced with losetup
-P. Fix it by moving the reread to after we unfreeze the queue.
Fixes: ecdd09597a ("block/loop: fix race between I/O and set_status")
Reported-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e112666b49 upstream.
If the journal has been aborted, we shouldn't mark the underlying
buffer head as dirty, since that will cause the metadata block to get
modified. And if the journal has been aborted, we shouldn't allow
this since it will almost certainly lead to a corrupted file system.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 907565337e upstream.
Userspace applications should be allowed to expect the membarrier system
call with MEMBARRIER_CMD_SHARED command to issue memory barriers on
nohz_full CPUs, but synchronize_sched() does not take those into
account.
Given that we do not want unrelated processes to be able to affect
real-time sensitive nohz_full CPUs, simply return ENOSYS when membarrier
is invoked on a kernel with enabled nohz_full CPUs.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
CC: Josh Triplett <josh@joshtriplett.org>
CC: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Rik van Riel <riel@redhat.com>
Acked-by: Lai Jiangshan <jiangshanlai@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0b0408745e upstream.
LPDDR memories can only handle up to 400 uncontrolled power off. Ensure the
proper power off sequence is used before shutting down the platform.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 857de6e007 upstream.
The device handler needs to check if a given queue belongs to a scsi
device; only then does it make sense to attach a device handler.
[mkp: dropped flags]
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c421530bf8 upstream.
The driver currently checks the SELF_TEST_FAILED first and then
KERNEL_PANIC next. Under error conditions(boot code failure) both
SELF_TEST_FAILED and KERNEL_PANIC can be set at the same time.
The driver has the capability to reset the controller on an KERNEL_PANIC,
but not on SELF_TEST_FAILED.
Fixed by first checking KERNEL_PANIC and then the others.
Fixes: e8b12f0fb8 ([SCSI] aacraid: Add new code for PMC-Sierra's SRC base controller family)
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <David.Carroll@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f54f2cb540 upstream.
This patch cleaned up queue configuration code, such that once
initialized, we should not touch msix_count value. This will prevent
incorrect numbers of MSI-X vectors requested while performing target
mode configuration.
[mkp: fixed Fixes: hash]
Fixes: d74595278f ("scsi: qla2xxx: Add multiple queue pair functionality.")
Signed-off-by: Michael Hernandez <michael.hernandez@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40630f4628 upstream.
On I/O errors, the Windows driver doesn't set data_transfer_length
on error conditions other than SRB_STATUS_DATA_OVERRUN.
In these cases we need to set data_transfer_length to 0,
indicating there is no data transferred. On SRB_STATUS_DATA_OVERRUN,
data_transfer_length is set by the Windows driver to the actual data transferred.
Reported-by: Shiva Krishna <Shiva.Krishna@nimblestorage.com>
Signed-off-by: Long Li <longli@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bba5dc332e upstream.
When sense message is present on error, we should pass along to the upper
layer to decide how to deal with the error.
This patch fixes connectivity issues with Fiber Channel devices.
Signed-off-by: Long Li <longli@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d36a19541f upstream.
The lvm2 sequence to manage dm-raid constructor flags that trigger a
rebuild or a reshape is defined as:
1) load table with flags (e.g. rebuild/delta_disks/data_offset)
2) clear out the flags in lvm2 metadata
3) store the lvm2 metadata, reload the table to reset the flags
previously established during the initial load (1) -- in order to
prevent repeatedly requesting a rebuild or a reshape on activation
Currently, loading an inactive table with rebuild/reshape flags
specified will cause dm-raid to rebuild/reshape on resume and thus start
updating the raid metadata (about the progress). When the second table
reload, to reset the flags, occurs the constructor accesses the volatile
progress state kept in the raid superblocks. Because the active mapping
is still processing the rebuild/reshape, that position will be stale by
the time the device is resumed.
In the reshape case, this causes data corruption by processing already
reshaped stripes again. In the rebuild case, it does _not_ cause data
corruption but instead involves superfluous rebuilds.
Fix by keeping the raid set frozen during the first resume and then
allow the rebuild/reshape during the second resume.
Fixes: 9dbd1aa3a ("dm raid: add reshaping support to the target")
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 37a098e9d1 upstream.
The sloppy nature of lockless access to percpu pointers
(s->current_path) in rr_select_path(), from multiple threads, is
causing some paths to used more than others -- which results in less
IO performance being observed.
Revert these upstream commits to restore truly symmetric round-robin
IO submission in DM multipath:
b0b477c dm round robin: use percpu 'repeat_count' and 'current_path'
802934b dm round robin: do not use this_cpu_ptr() without having preemption disabled
There is no benefit to all this complexity if repeat_count = 1 (which is
the recommended default).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca763d0a53 upstream.
A rounding bug due to compiler generated temporary being 32bit was found
in remap_to_cache(). A localized cast in remap_to_cache() fixes the
corruption but this preferred fix (changing from uint32_t to sector_t)
eliminates potential for future rounding errors elsewhere.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 30582c25a4 upstream.
Until now, the trans_stat information of passive devfreq is not updated.
This patch updates the trans_stat information after setting the target
frequency of passive devfreq device.
Fixes: 996133119f ("PM / devfreq: Add new passive governor")
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bcf23c79c4 upstream.
The devfreq using passive governor is not able to change the governor.
So, the user can not change the governor through 'available_governor' sysfs
entry. Also, the devfreq which don't use the passive governor is not able to
change to 'passive' governor on the fly.
Fixes: 996133119f ("PM / devfreq: Add new passive governor")
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bc15ed663e upstream.
On failure to return a pathname from ima_d_path(), a pointer to
dname is returned, which is subsequently used in the IMA measurement
list, the IMA audit records, and other audit logging. Saving the
pointer to dname for later use has the potential to race with rename.
Intead of returning a pointer to dname on failure, this patch returns
a pointer to a copy of the filename.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 95e91b831f upstream.
The issue is described here, with a nice testcase:
https://bugzilla.kernel.org/show_bug.cgi?id=192931
The problem is that shmat() calls do_mmap_pgoff() with MAP_FIXED, and
the address rounded down to 0. For the regular mmap case, the
protection mentioned above is that the kernel gets to generate the
address -- arch_get_unmapped_area() will always check for MAP_FIXED and
return that address. So by the time we do security_mmap_addr(0) things
get funky for shmat().
The testcase itself shows that while a regular user crashes, root will
not have a problem attaching a nil-page. There are two possible fixes
to this. The first, and which this patch does, is to simply allow root
to crash as well -- this is also regular mmap behavior, ie when hacking
up the testcase and adding mmap(... |MAP_FIXED). While this approach
is the safer option, the second alternative is to ignore SHM_RND if the
rounded address is 0, thus only having MAP_SHARED flags. This makes the
behavior of shmat() identical to the mmap() case. The downside of this
is obviously user visible, but does make sense in that it maintains
semantics after the round-down wrt 0 address and mmap.
Passes shm related ltp tests.
Link: http://lkml.kernel.org/r/1486050195-18629-1-git-send-email-dave@stgolabs.net
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Reported-by: Gareth Evans <gareth.evans@contextis.co.uk>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 71ab6cfe88 upstream.
get_scan_count() considers the whole node LRU size when
- doing SCAN_FILE due to many page cache inactive pages
- calculating the number of pages to scan
In both cases this might lead to unexpected behavior especially on 32b
systems where we can expect lowmem memory pressure very often.
A large highmem zone can easily distort SCAN_FILE heuristic because
there might be only few file pages from the eligible zones on the node
lru and we would still enforce file lru scanning which can lead to
trashing while we could still scan anonymous pages.
The later use of lruvec_lru_size can be problematic as well. Especially
when there are not many pages from the eligible zones. We would have to
skip over many pages to find anything to reclaim but shrink_node_memcg
would only reduce the remaining number to scan by SWAP_CLUSTER_MAX at
maximum. Therefore we can end up going over a large LRU many times
without actually having chance to reclaim much if anything at all. The
closer we are out of memory on lowmem zone the worse the problem will
be.
Fix this by filtering out all the ineligible zones when calculating the
lru size for both paths and consider only sc->reclaim_idx zones.
The patch would need to be tweaked a bit to apply to 4.10 and older but
I will do that as soon as it hits the Linus tree in the next merge
window.
Link: http://lkml.kernel.org/r/20170117103702.28542-3-mhocko@kernel.org
Fixes: b2e18757f2 ("mm, vmscan: begin reclaiming pages on a per-node basis")
Signed-off-by: Michal Hocko <mhocko@suse.com>
Tested-by: Trevor Cordes <trevor@tecnopolis.ca>
Acked-by: Minchan Kim <minchan@kernel.org>
Acked-by: Hillf Danton <hillf.zj@alibaba-inc.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd8416c477 upstream.
With rw_page, page_endio is used for completing IO on a page and it
propagates write error to the address space if the IO fails. The
problem is it accesses page->mapping directly which might be okay for
file-backed pages but it shouldn't for anonymous page. Otherwise, it
can corrupt one of field from anon_vma under us and system goes panic
randomly.
swap_writepage
bdev_writepage
ops->rw_page
I encountered the BUG during developing new zram feature and it was
really hard to figure it out because it made random crash, somtime
mmap_sem lockdep, sometime other places where places never related to
zram/zsmalloc, and not reproducible with some configuration.
When I consider how that bug is subtle and people do fast-swap test with
brd, it's worth to add stable mark, I think.
Fixes: dd6bd0d9c7 ("swap: use bdev_read_page() / bdev_write_page()")
Signed-off-by: Minchan Kim <minchan@kernel.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e02dc017c3 upstream.
When @node_reclaim_node isn't 0, the page allocator tries to reclaim
pages if the amount of free memory in the zones are below the low
watermark. On Power platform, none of NUMA nodes are scanned for page
reclaim because no nodes match the condition in zone_allows_reclaim().
On Power platform, RECLAIM_DISTANCE is set to 10 which is the distance
of Node-A to Node-A. So the preferred node even won't be scanned for
page reclaim.
__alloc_pages_nodemask()
get_page_from_freelist()
zone_allows_reclaim()
Anton proposed the test code as below:
# cat alloc.c
:
int main(int argc, char *argv[])
{
void *p;
unsigned long size;
unsigned long start, end;
start = time(NULL);
size = strtoul(argv[1], NULL, 0);
printf("To allocate %ldGB memory\n", size);
size <<= 30;
p = malloc(size);
assert(p);
memset(p, 0, size);
end = time(NULL);
printf("Used time: %ld seconds\n", end - start);
sleep(3600);
return 0;
}
The system I use for testing has two NUMA nodes. Both have 128GB
memory. In below scnario, the page caches on node#0 should be reclaimed
when it encounters pressure to accommodate request of allocation.
# echo 2 > /proc/sys/vm/zone_reclaim_mode; \
sync; \
echo 3 > /proc/sys/vm/drop_caches; \
# taskset -c 0 cat file.32G > /dev/null; \
grep FilePages /sys/devices/system/node/node0/meminfo
Node 0 FilePages: 33619712 kB
# taskset -c 0 ./alloc 128
# grep FilePages /sys/devices/system/node/node0/meminfo
Node 0 FilePages: 33619840 kB
# grep MemFree /sys/devices/system/node/node0/meminfo
Node 0 MemFree: 186816 kB
With the patch applied, the pagecache on node-0 is reclaimed when its
free memory is running out. It's the expected behaviour.
# echo 2 > /proc/sys/vm/zone_reclaim_mode; \
sync; \
echo 3 > /proc/sys/vm/drop_caches
# taskset -c 0 cat file.32G > /dev/null; \
grep FilePages /sys/devices/system/node/node0/meminfo
Node 0 FilePages: 33605568 kB
# taskset -c 0 ./alloc 128
# grep FilePages /sys/devices/system/node/node0/meminfo
Node 0 FilePages: 1379520 kB
# grep MemFree /sys/devices/system/node/node0/meminfo
Node 0 MemFree: 317120 kB
Fixes: 5f7a75acdb ("mm: page_alloc: do not cache reclaim distances")
Link: http://lkml.kernel.org/r/1486532455-29613-1-git-send-email-gwshan@linux.vnet.ibm.com
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9c25702cee upstream.
Currently we call copy_page_to_iter() for uncached reading into a pipe.
This is wrong because it treats pages as VFS cache pages and copies references
rather than actual data. When we are trying to read from the pipe we end up
calling page_cache_pipe_buf_confirm() which returns -ENODATA. This error
is translated into 0 which is returned to a user.
This issue is reproduced by running xfs-tests suite (generic test #249)
against mount points with "cache=none". Fix it by mapping pages manually
and calling copy_to_iter() that copies data into the pipe.
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d70fe9d9c upstream.
Since commit 1107d065fd ("tpm_tis: Introduce intermediate layer for
TPM access") Atmel 3203 TPM on ThinkPad X61S (TPM firmware version 13.9)
no longer works. The initialization proceeds fine until we get and
start using chip-reported timeouts - and the chip reports C and D
timeouts of zero.
It turns out that until commit 8e54caf407 ("tpm: Provide a generic
means to override the chip returned timeouts") we had actually let
default timeout values remain in this case, so let's bring back this
behavior to make chips like Atmel 3203 work again.
Use a common code that was introduced by that commit so a warning is
printed in this case and /sys/class/tpm/tpm*/timeouts correctly says the
timeouts aren't chip-original.
Fixes: 1107d065fd ("tpm_tis: Introduce intermediate layer for TPM access")
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e42a46b6f5 upstream.
It is allowed to call regulator_get with a NULL dev argument
(_regulator_get explicitly checks for it) but this causes an error later
when printing /sys/kernel/debug/regulator_summary.
Fix this by explicitly handling "deviceless" consumers in the debugfs code.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4474f4c40a upstream.
The stm is automatically enabled when an application sets the policy
via ->link() call back by using coresight_enable(), which keeps the
refcount of the current users of the STM. However, the unlink() callback
issues stm_disable() directly, which leaves the STM turned off, without
the coresight layer knowing about it. This prevents any further uses
of the STM hardware as the coresight layer still thinks the STM is
turned on and doesn't enable the hardware when required. Even manually
enabling the STM via sysfs can't really enable the hw.
e.g,
$ echo 1 > $CS_DEVS/$ETR/enable_sink
$ mkdir -p $CONFIG_FS/stp-policy/$source.0/stm_test/
$ echo 32768 65535 > $CONFIG_FS/stp-policy/$source.0/stm_test/channels
$ echo 64 > $CS_DEVS/$source/traceid
$ ./stm_app
Sending 64000 byte blocks of pattern 0 at 0us intervals
Success to map channel(32768~32783) to 0xffffa95fa000
Sending on channel 32768
$ dd if=/dev/$ETR of=~/trace.bin.1
597+1 records in
597+1 records out
305920 bytes (306 kB) copied, 0.399952 s, 765 kB/s
$ ./stm_app
Sending 64000 byte blocks of pattern 0 at 0us intervals
Success to map channel(32768~32783) to 0xffff7e9e2000
Sending on channel 32768
$ dd if=/dev/$ETR of=~/trace.bin.2
0+0 records in
0+0 records out
0 bytes (0 B) copied, 0.0232083 s, 0.0 kB/s
Note that we don't get any data from the ETR for the second session.
Also dmesg shows :
[ 77.520458] coresight-tmc 20800000.etr: TMC-ETR enabled
[ 77.537097] coresight-replicator etr_replicator@20890000: REPLICATOR enabled
[ 77.558828] coresight-replicator main_replicator@208a0000: REPLICATOR enabled
[ 77.581068] coresight-funnel 208c0000.main_funnel: FUNNEL inport 0 enabled
[ 77.602217] coresight-tmc 20840000.etf: TMC-ETF enabled
[ 77.618422] coresight-stm 20860000.stm: STM tracing enabled
[ 139.554252] coresight-stm 20860000.stm: STM tracing disabled
# End of first tracing session
[ 146.351135] coresight-tmc 20800000.etr: TMC read start
[ 146.514486] coresight-tmc 20800000.etr: TMC read end
# Note that the STM is not turned on via stm_generic_link()->coresight_enable()
# and hence none of the components are turned on.
[ 152.479080] coresight-tmc 20800000.etr: TMC read start
[ 152.542632] coresight-tmc 20800000.etr: TMC read end
This patch fixes the problem by balancing the unlink operation by using
the coresight_disable(), keeping the coresight layer in sync with the
hardware state and thus allowing normal usage of the STM component.
Fixes: commit 237483aa5c ("coresight: stm: adding driver for CoreSight STM component")
Cc: Pratik Patel <pratikp@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Reported-by: Robert Walker <robert.walker@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e01700602 upstream.
gcc-7 detects that wlanhdr_to_ethhdr() in two drivers calls memcpy() with
a destination argument that an earlier function call may have set to NULL:
staging/rtl8188eu/core/rtw_recv.c: In function 'wlanhdr_to_ethhdr':
staging/rtl8188eu/core/rtw_recv.c:1318:2: warning: argument 1 null where non-null expected [-Wnonnull]
staging/rtl8712/rtl871x_recv.c: In function 'r8712_wlanhdr_to_ethhdr':
staging/rtl8712/rtl871x_recv.c:649:2: warning: argument 1 null where non-null expected [-Wnonnull]
I'm fixing this by adding a NULL pointer check and returning failure
from the function, which is hopefully already handled properly.
This seems to date back to when the drivers were originally added,
so backporting the fix to stable seems appropriate. There are other
related realtek drivers in the kernel, but none of them contain a
function with a similar name or produce this warning.
Fixes: 1cc18a22b9 ("staging: r8188eu: Add files for new driver - part 5")
Fixes: 2865d42c78 ("staging: r8712u: Add the new driver to the mainline kernel")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc7ffefdcc upstream.
This is unbreaking another of those "stealth" janitor
patches that got in and subtly broke some things.
sv_cpt_data is a pointer to pointer, so need to
dereference it twice to allocate the correct structure size.
Fixes: 9899cb68c6 ("Staging: lustre: rpc: Use sizeof type *pointer instead of sizeof type.")
CC: Sandhya Bankar <bankarsandhya512@gmail.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Reviewed-by: James Simmons <jsimmons@infradead.org>
Reviewed-by: Doug Oucharek <doug.s.oucharek@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 33b8807a6f upstream.
The loopback driver allows the user to set a minimum delay of up to one
second to be inserted between test iterations (i.e. request
submissions). The delay is currently specified in microseconds and is
implemented using udelay.
Busy looping for long periods is not just anti-social; udelay must not
be used for delays longer than a few milliseconds due to the risk of
integer overflow.
Replace the broken udelay with a usleep_range with a 100 us range for
short delays (< 20 ms) and otherwise revert to using msleep.
Fixes: b36f04fa94 ("greybus: loopback: Convert thread delay to microseconds")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 82dbe987b7 upstream.
If sensor attributes were never read, the pwm control data has not been
initiialized, which can cause wrong driver behavior. Ensure that cached
data is current before acting on it.
Reported-by: Kevin Folz <kfolz@evertz.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c7b8ca1ae upstream.
In IT8620E, after setting pwm control to manual, it was observed that
pwm values for fan 4..6 have reversed results (writing 0 results in fans
running at full speed, writing 255 results in fans turned off).
With the new PWM control, pwm polarity for pwm control 4..6 is specified
in its pwm control registers. Those registers are overwritten when setting
the pwm mode or the temperature mapping. Do not touch bit 2..6 of pwm
control registers on register writes to fix the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 29693efcea upstream.
On this machine, the micmute button is connected to Line2 of the
codec and the micmute led is connected to GPIO2 of the codec.
After applying this quirk, both hotkey and led work well.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f3ac9f7376 upstream.
The sequencer FIFO management has a bug that may lead to a corruption
(shortage) of the cell linked list. When a sequencer client faces an
error at the event delivery, it tries to put back the dequeued cell.
When the first queue was put back, this forgot the tail pointer
tracking, and the link will be screwed up.
Although there is no memory corruption, the sequencer client may stall
forever at exit while flushing the pending FIFO cells in
snd_seq_pool_done(), as spotted by syzkaller.
This patch addresses the missing tail pointer tracking at
snd_seq_fifo_cell_putback(). Also the patch makes sure to clear the
cell->enxt pointer at snd_seq_fifo_event_in() for avoiding a similar
mess-up of the FIFO linked list.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 15c75b09f8 upstream.
Currently ctxfi driver tries to set only the 64bit DMA mask on 64bit
architectures, and bails out if it fails. This causes a problem on
some platforms since the 64bit DMA isn't always guaranteed. We should
fall back to the default 32bit DMA when 64bit DMA fails.
Fixes: 6d74b86d3c ("ALSA: ctxfi - Allow 64bit DMA")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 71321eb3f2 upstream.
When a user sets a too small ticks with a fine-grained timer like
hrtimer, the kernel tries to fire up the timer irq too frequently.
This may lead to the condensed locks, eventually the kernel spinlock
lockup with warnings.
For avoiding such a situation, we define a lower limit of the
resolution, namely 1ms. When the user passes a too small tick value
that results in less than that, the kernel returns -EINVAL now.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7480b34ad upstream.
Like for Sunrise Point, the total stream number of Lewisburg's
input and output stream exceeds 15 (GCAP is 0x9701), which will
cause some streams do not work because of the overflow on
SDxCTL.STRM field if using the legacy stream tag allocation method.
Fixes: 5cf92c8b3d ("ALSA: hda - Add Intel Lewisburg device IDs Audio")
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9f1bc2c4c5 upstream.
The issue is the same as "dd9aa335c880 ALSA: hda/realtek - Can't adjust
speaker's volume on a Dell AIO", the output requires to connect to a node
with Amp-out capability.
Applying the same fixup "ALC298_FIXUP_SPK_VOLUME" can fix the issue.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef8d02d4a2 upstream.
Enable DMA on usart3 to get a more reliable console. This is especially
useful for automation and kernelci were a kernel with PROVE_LOCKING enabled
is quite susceptible to character loss, resulting in tests failure.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 379f831a92 upstream.
Commit a92e7c3d82 ("spi: s3c64xx: consider the case when the CS
line is not connected") introduced an inconsistency between the
binding, where the disconnected CS line was marked as
'no-cs-readback', and the driver.
The driver is erroneously checking for that attribute with
property name of 'broken-cs'.
Check for 'no-cs-readback' in the driver as well.
Fixes: a92e7c3d82 ("spi: s3c64xx: consider the case when the CS line is not connected")
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 98d85f3cb9 upstream.
When the functions replaced media entity types, the range which was
allowed for the types was incorrect. This meant that media entity types
for specific devices were not passed correctly to the userspace through
MEDIA_IOC_ENUM_ENTITIES. Fix it.
Fixes: commit b2cd27448b ("[media] media-device: map new functions into old types for legacy API")
Reported-and-tested-by: Antti Laakso <antti.laakso@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0ffb94b6cc upstream.
Setting GPIOs during probe causes null pointer deference when
GPIOLIB was not selected by Kconfig. Initialize driver private
field before calling set gpios.
It is regressing bug since 4.9.
Fixes: 07fdf7d9f1 ("[media] cxd2820r: add I2C driver bindings")
Reported-by: Chris Rankin <rankincj@gmail.com>
Tested-by: Chris Rankin <rankincj@gmail.com>
Tested-by: Håkan Lennestål <hakan.lennestal@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ebf75774f upstream.
In vpfe_s_fmt(), when the sensor format and the requested format were
the same, bpp was assigned to vpfe->bpp without being initialized first.
Grab the bpp value that is currently used by using __vpfe_get_format()
instead of its wrapper, vpfe_try_fmt().
This use of uninitialized variable has been found by compiling the
kernel with clang.
Fixes: 417d2e507e ("[media] media: platform: add VPFE capture driver
support for AM437X")
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb9bc4689b upstream.
get_frame_info() calculates the offset of the return address within a
stack frame simply by dividing a the bottom 16 bits of the instruction,
treated as a signed integer, by the size of a long. Whilst this works
for MIPS32 & MIPS64 ISAs where the sw or sd instructions are used, it's
incorrect for microMIPS where encodings differ. The result is that we
typically completely fail to unwind the stack on microMIPS.
Fix this by adjusting is_ra_save_ins() to calculate the return address
offset, and take into account the various different encodings there in
the same place as we consider whether an instruction is storing the
ra/$31 register.
With this we are now able to unwind the stack for kernels targetting the
microMIPS ISA, for example we can produce:
Call Trace:
[<80109e1f>] show_stack+0x63/0x7c
[<8011ea17>] __warn+0x9b/0xac
[<8011ea45>] warn_slowpath_fmt+0x1d/0x20
[<8013fe53>] register_console+0x43/0x314
[<8067c58d>] of_setup_earlycon+0x1dd/0x1ec
[<8067f63f>] early_init_dt_scan_chosen_stdout+0xe7/0xf8
[<8066c115>] do_early_param+0x75/0xac
[<801302f9>] parse_args+0x1dd/0x308
[<8066c459>] parse_early_options+0x25/0x28
[<8066c48b>] parse_early_param+0x2f/0x38
[<8066e8cf>] setup_arch+0x113/0x488
[<8066c4f3>] start_kernel+0x57/0x328
---[ end trace 0000000000000000 ]---
Whereas previously we only produced:
Call Trace:
[<80109e1f>] show_stack+0x63/0x7c
---[ end trace 0000000000000000 ]---
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: 34c2f668d0 ("MIPS: microMIPS: Add unaligned access support.")
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14532/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b6c7a324df upstream.
get_frame_info() is meant to iterate over up to the first 128
instructions within a function, but for microMIPS kernels it will not
reach that many instructions unless the function is 512 bytes long since
we calculate the maximum number of instructions to check by dividing the
function length by the 4 byte size of a union mips_instruction. In
microMIPS kernels this won't do since instructions are variable length.
Fix this by instead checking whether the pointer to the current
instruction has reached the end of the function, and use max_insns as a
simple constant to check the number of iterations against.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: 34c2f668d0 ("MIPS: microMIPS: Add unaligned access support.")
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14530/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a3552dace7 upstream.
During stack unwinding we call a number of functions to determine what
type of instruction we're looking at. The union mips_instruction pointer
provided to them may be pointing at a 2 byte, but not 4 byte, aligned
address & we thus cannot directly access the 4 byte wide members of the
union mips_instruction. To avoid this is_ra_save_ins() copies the
required half-words of the microMIPS instruction to a correctly aligned
union mips_instruction on the stack, which it can then access safely.
The is_jump_ins() & is_sp_move_ins() functions do not correctly perform
this temporary copy, and instead attempt to directly dereference 4 byte
fields which may be misaligned and lead to an address exception.
Fix this by copying the instruction halfwords to a temporary union
mips_instruction in get_frame_info() such that we can provide a 4 byte
aligned union mips_instruction to the is_*_ins() functions and they do
not need to deal with misalignment themselves.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: 34c2f668d0 ("MIPS: microMIPS: Add unaligned access support.")
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14529/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ccaf7caf2c upstream.
get_frame_info() can be called in microMIPS kernels with the ISA bit
already clear. For example this happens when unwind_stack_by_address()
is called because we begin with a PC that has the ISA bit set & subtract
the (odd) offset from the preceding symbol (which does not have the ISA
bit set). Since get_frame_info() unconditionally subtracts 1 from the PC
in microMIPS kernels it incorrectly misaligns the address it then
attempts to access code at, leading to an address error exception.
Fix this by using msk_isa16_mode() to clear the ISA bit, which allows
get_frame_info() to function regardless of whether it is provided with a
PC that has the ISA bit set or not.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: 34c2f668d0 ("MIPS: microMIPS: Add unaligned access support.")
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14528/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 774f0c6419 upstream.
Disabling ethernet during reboot (only to enable it again when the
ethernet driver attaches) can put the chip into a faulty state where it
corrupts the header of all incoming packets.
This happens if packets arrive during the time window where the core is
disabled, and it can be easily reproduced by rebooting while sending a
flood ping to the broadcast address.
Fixes: 95135bfa7e ("MIPS: Lantiq: Deactivate most of the devices by default")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: John Crispin <john@phrozen.org>
Cc: hauke.mehrtens@lantiq.com
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15078/
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 884b426917 upstream.
If copy_from_user is called with a large buffer (>= 128 bytes) and the
userspace buffer refers partially to unreadable memory, then it is
possible for Octeon's copy_from_user to report the wrong number of bytes
have been copied. In the case where the buffer size is an exact multiple
of 128 and the fault occurs in the last 64 bytes, copy_from_user will
report that all the bytes were copied successfully but leave some
garbage in the destination buffer.
The bug is in the main __copy_user_common loop in octeon-memcpy.S where
in the middle of the loop, src and dst are incremented by 128 bytes. The
l_exc_copy fault handler is used after this but that assumes that
"src < THREAD_BUADDR($28)". This is not the case if src has already been
incremented.
Fix by adding an extra fault handler which rewinds the src and dst
pointers 128 bytes before falling though to l_exc_copy.
Thanks to the pwritev test from the strace test suite for originally
highlighting this bug!
Fixes: 5b3b16880f ("MIPS: Add Cavium OCTEON processor support ...")
Signed-off-by: James Cowgill <James.Cowgill@imgtec.com>
Acked-by: David Daney <david.daney@cavium.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14978/
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66fd848cad upstream.
For certain arguments such as saddr = 0xc0a8fd60, daddr = 0xc0a8fda1,
len = 80, proto = 17, sum = 0x7eae049d there will be a carry when
folding the intermediate 64 bit checksum to 32 bit but the code doesn't
add the carry back to the one's complement sum, thus an incorrect result
will be generated.
Reported-by: Mark Zhang <bomb.zhang@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fa7f138ac4 upstream.
The buffered write failure handling code in
xfs_file_iomap_end_delalloc() has a couple minor problems. First, if
written == 0, start_fsb is not rounded down and it fails to kill off a
delalloc block if the start offset is block unaligned. This results in a
lingering delalloc block and broken delalloc block accounting detected
at unmount time. Fix this by rounding down start_fsb in the unlikely
event that written == 0.
Second, it is possible for a failed overwrite of a delalloc extent to
leave dirty pagecache around over a hole in the file. This is because is
possible to hit ->iomap_end() on write failure before the iomap code has
attempted to allocate pagecache, and thus has no need to clean it up. If
the targeted delalloc extent was successfully written by a previous
write, however, then it does still have dirty pages when ->iomap_end()
punches out the underlying blocks. This ultimately results in writeback
over a hole. To fix this problem, unconditionally punch out the
pagecache from XFS before the associated delalloc range.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 575ddce050 upstream.
In the function rtl_usb_start we pre-allocate a certain number of urbs
for RX path but they will not be freed when calling rtl_usb_stop. This
results in leaking urbs when doing ifconfig up and down. Eventually,
the system has no available urbs.
Signed-off-by: Michael Schenk <michael.schenk@albis-elcon.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5f478e4ea5 upstream.
When !CONFIG_CGROUP_WRITEBACK, bdi has single bdi_writeback_congested
at bdi->wb_congested. cgwb_bdi_init() allocates it with kzalloc() and
doesn't do further initialization. This usually works fine as the
reference count gets bumped to 1 by wb_init() and the put from
wb_exit() releases it.
However, when wb_init() fails, it puts the wb base ref automatically
freeing the wb and the explicit kfree() in cgwb_bdi_init() error path
ends up trying to free the same pointer the second time causing a
double-free.
Fix it by explicitly initilizing the refcnt to 1 and putting the base
ref from cgwb_bdi_destroy().
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Fixes: a13f35e871 ("writeback: don't embed root bdi_writeback_congested in bdi_writeback")
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ffab9188e4 upstream.
ACPICA commit b59347d0b8b676cb555fe8da5cad08fcd4eeb0d3
The following commit cleans up compiler specific inclusions:
Commit: 9fa1cebdbf
Subject: ACPICA: OSL: Cleanup the inclusion order of the compiler-specific headers
But breaks one thing due to the following old issue:
Buidling Linux kernel with Intel compiler originally depends on acgcc.h
not acintel.h.
So after making Intel compiler build working in ACPICA upstream by
correctly using acintel.h, it becomes unable to build Linux kernel using
Intel compiler as there is no acintel.h in the kernel source tree.
This patch releases acintel.h to Linux kernel and fixes its inclusion in
acenv.h.
Fixes: 9fa1cebdbf (ACPICA: OSL: Cleanup the inclusion order of the compiler-specific headers)
Link: https://github.com/acpica/acpica/commit/b59347d0
Tested-by: Stepan M Mishura <stepan.m.mishura@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dfe75ff8ca upstream.
Commit 3bb398d925 ("netfilter: nf_ct_helper: disable automatic helper
assignment") is causing behavior regressions in firewalls, as traffic
handled by conntrack helpers is now by default not passed through even
though it was before due to missing CT targets (which were not necessary
before this commit).
The default had to be switched off due to security reasons [1] [2] and
therefore should stay the way it is, but let's be friendly to firewall
admins and issue a warning the first time we're in situation where packet
would be likely passed through with the old default but we're likely going
to drop it on the floor now.
Rewrite the code a little bit as suggested by Linus, so that we avoid
spaghettiing the code even more -- namely the whole decision making
process regarding helper selection (either automatic or not) is being
separated, so that the whole logic can be simplified and code (condition)
duplication reduced.
[1] https://cansecwest.com/csw12/conntrack-attack.pdf
[2] https://home.regit.org/netfilter-en/secure-use-of-helpers/
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6cf18e6927 upstream.
This interrupt handler is broken in several ways:
- It loops forever when the op code is not decodeable
- It never returns IRQ_HANDLED because the only way to exit the loop
returns IRQ_NONE unconditionally.
The whole concept of this is broken. Creating devices in an interrupt
handler is beyond any point of sanity.
Make it at least behave halfways sane so accidental users do not have to
deal with a hard to debug lockup.
Fixes: e809c22b8f ("goldfish: add the goldfish virtual bus")
Reported-by: Gabriel C <nix.or.die@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 47512cfd0d upstream.
The goldfish platform code registers the platform device unconditionally
which causes havoc in several ways if the goldfish_pdev_bus driver is
enabled:
- Access to the hardcoded physical memory region, which is either not
available or contains stuff which is completely unrelated.
- Prevents that the interrupt of the serial port can be requested
- In case of a spurious interrupt it goes into a infinite loop in the
interrupt handler of the pdev_bus driver (which needs to be fixed
seperately).
Add a 'goldfish' command line option to make the registration opt-in when
the platform is compiled in.
I'm seriously grumpy about this engineering trainwreck, which has seven
SOBs from Intel developers for 50 lines of code. And none of them figured
out that this is broken. Impressive fail!
Fixes: ddd70cf93d ("goldfish: platform device for x86")
Reported-by: Gabriel C <nix.or.die@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 14816b16fa upstream.
Since commit 4a51096937 ("tty: Make tty_files_lock per-tty") a new
tty_struct spin lock is taken in the tty release path, but the
USB-serial-console hack was never updated hence leaving the lock of its
"fake" tty uninitialised. This was eventually detected by lockdep.
Make sure to initialise the new lock also for the fake tty to address
this regression.
Yes, this code is a mess, but cleaning it up is left for another day.
Fixes: 4a51096937 ("tty: Make tty_files_lock per-tty")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9fef37d7cf upstream.
The current implementation failed to detect short transfers, something
which could lead to bits of the uninitialised heap transfer buffer
leaking to user space.
Fixes: 149fc791a4 ("USB: ark3116: Setup some basic infrastructure for new ark3116 driver.")
Fixes: f4c1e8d597 ("USB: ark3116: Make existing functions 16450-aware and add close and release functions.")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2eee05020a upstream.
The opticon driver used a control request at open to trigger a CTS
status notification to be sent over the bulk-in pipe. When the driver
was converted to using the generic read implementation, an inverted test
prevented this request from being sent, something which could lead to
TIOCMGET reporting an incorrect CTS state.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 7a6ee2b027 ("USB: opticon: switch to generic read implementation")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ed8d41023 upstream.
Make sure to detect short control transfers and return zero on success
when retrieving the modem status.
This fixes the TIOCMGET implementation which since e1ed212d85 ("USB:
spcp8x5: add proper modem-status support") has returned TIOCM_LE on
successful retrieval, and avoids leaking bits from the stack on short
transfers.
This also fixes the carrier-detect implementation which since the above
mentioned commit unconditionally has returned true.
Fixes: e1ed212d85 ("USB: spcp8x5: add proper modem-status support")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a6bb1e17a3 upstream.
FTDI devices use a receive latency timer to periodically empty the
receive buffer and report modem and line status (also when the buffer is
empty).
When a break or error condition is detected the corresponding status
flags will be set on a packet with nonzero data payload and the flags
are not updated until the break is over or further characters are
received.
In order to avoid over-reporting break and error conditions, these flags
must therefore only be processed for packets with payload.
This specifically fixes the case where after an overrun, the error
condition is continuously reported and NULL-characters inserted until
further data is received.
Reported-by: Michael Walle <michael@walle.cc>
Fixes: 72fda3ca6f ("USB: serial: ftd_sio: implement sysrq handling on
break")
Fixes: 166ceb6907 ("USB: ftdi_sio: clean up line-status handling")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c6dce26266 upstream.
Since commit 557aaa7ffa ("ft232: support the ASYNC_LOW_LATENCY
flag") the FTDI driver has been using a receive latency-timer value of
1 ms instead of the device default of 16 ms.
The latency timer is used to periodically empty a non-full receive
buffer, but a status header is always sent when the timer expires
including when the buffer is empty. This means that a two-byte bulk
message is received every millisecond also for an otherwise idle port as
long as it is open.
Let's restore the pre-2009 behaviour which reduces the rate of the
status messages to 1/16th (e.g. interrupt frequency drops from 1 kHz to
62.5 Hz) by not setting ASYNC_LOW_LATENCY by default.
Anyone willing to pay the price for the minimum-latency behaviour should
set the flag explicitly instead using the TIOCSSERIAL ioctl or a tool
such as setserial (e.g. setserial /dev/ttyUSB0 low_latency).
Note that since commit 0cbd81a9f6 ("USB: ftdi_sio: remove
tty->low_latency") the ASYNC_LOW_LATENCY flag has no other effects but
to set a minimal latency timer.
Reported-by: Antoine Aubert <a.aubert@overkiz.com>
Fixes: 557aaa7ffa ("ft232: support the ASYNC_LOW_LATENCY flag")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 427c3a95e3 upstream.
Make sure to detect short responses when fetching the modem status in
order to avoid parsing uninitialised buffer data and having bits of it
leak to user space.
Note that we still allow for short 1-byte responses.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5182c2cf2a upstream.
Fix another NULL-pointer dereference at open should a malicious device
lack an interrupt-in endpoint.
Note that the driver has a broken check for an interrupt-in endpoint
which means that an interrupt URB has never even been submitted.
Fixes: 3f5429746d ("USB: Moschip 7840 USB-Serial Driver")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit abe81f3b8e upstream.
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/tty/serial/msm_serial.ko | grep alias
$
After this patch:
$ modinfo drivers/tty/serial/msm_serial.ko | grep alias
alias: of:N*T*Cqcom,msm-uartdmC*
alias: of:N*T*Cqcom,msm-uartdm
alias: of:N*T*Cqcom,msm-uartC*
alias: of:N*T*Cqcom,msm-uart
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e623a9e9de ]
Commit 34b88a68f2 ("net: Fix use after free in the recvmmsg exit path"),
changed the exit path of recvmmsg to always return the datagrams
variable and modified the error paths to set the variable to the error
code returned by recvmsg if necessary.
However in the case sock_error returned an error, the error code was
then ignored, and recvmmsg returned 0.
Change the error path of recvmmsg to correctly return the error code
of sock_error.
The bug was triggered by using recvmmsg on a CAN interface which was
not up. Linux 4.6 and later return 0 in this case while earlier
releases returned -ENETDOWN.
Fixes: 34b88a68f2 ("net: Fix use after free in the recvmmsg exit path")
Signed-off-by: Maxime Jayat <maxime.jayat@mobile-devices.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ca4ef4574f ]
The skbs processed by ip_cmsg_recv() are not guaranteed to
be linear e.g. when sending UDP packets over loopback with
MSGMORE.
Using csum_partial() on [potentially] the whole skb len
is dangerous; instead be on the safe side and use skb_checksum().
Thanks to syzkaller team to detect the issue and provide the
reproducer.
v1 -> v2:
- move the variable declaration in a tighter scope
Fixes: ad6f939ab1 ("ip: Add offset parameter to ip_cmsg_recv")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e716953071 ]
Resizing currently drops consumer lock. This can cause entries to be
reordered, which isn't good in itself. More importantly, consumer can
detect a false ring empty condition and block forever.
Further, nesting of consumer within producer lock is problematic for
tun, since it produces entries in a BH, which causes a lock order
reversal:
CPU0 CPU1
---- ----
consume:
lock(&(&r->consumer_lock)->rlock);
resize:
local_irq_disable();
lock(&(&r->producer_lock)->rlock);
lock(&(&r->consumer_lock)->rlock);
<Interrupt>
produce:
lock(&(&r->producer_lock)->rlock);
To fix, nest producer lock within consumer lock during resize,
and keep consumer lock during the whole swap operation.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: stable@vger.kernel.org
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-02-26 11:09:17 +01:00
1735 changed files with 319029 additions and 10177 deletions
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
