bcm2708_fb: Disable warning when calling dma_alloc_coherent

When we boot the kernel on the rpi4/3/2, we sometimes could see the
warning calltrace like below:

bcm2708_fb soc:fb: FB found 1 display(s)
cma: cma_alloc: alloc failed, req-size: 1753 pages, ret: -12
WARNING: CPU: 2 PID: 1 at mm/page_alloc.c:4702 __alloc_pages_nodemask+0x284/0x2c8
Modules linked in:
CPU: 2 PID: 1 Comm: swapper/0 Not tainted 5.3.0-1013-raspi2 #15-Ubuntu
Hardware name: Raspberry Pi 3 Model B Plus Rev 1.3 (DT)
pstate: 20400005 (nzCv daif +PAN -UAO)
pc : __alloc_pages_nodemask+0x284/0x2c8
lr : __dma_direct_alloc_pages+0x100/0x1e8
sp : ffff0000100238a0
x29: ffff0000100238a0 x28: 0000000000000000
x27: ffffa7c578867580 x26: ffffa7c57786a080
...

After investigation, I found there are two situations which could
introduce this calltrace.
 1) booting the arm64 kernel on rpi4 boards without the monitor
 connected, in this situation, the xres and yres euqal to 0, so the
 dma_alloc_coherent wants to alloc a memory region with 0 size, this
 will result the get_order() returns (BITS_PER_LONG - PAGE_SHIFT),
 then it will introduce the calltrace because
 unlikely(order >= MAX_ORDER) is true (mm/page_alloc.c)
 2) booting the kernel on rpi2/3 boards with a high resolution monitor
 connected, in this case the xres * yres is too big, the cma_alloc
 doens't have enough memory for it, and finally it will also introduce
 the calltrace by unlikely(order >= MAX_ORDER) is true.

The bcm2708_fb could handle the situation of failure on calling
dma_alloc_coherent, and the driver itself will print some log to
notify users that this alloc fails. So we don't need the mm/page_alloc
to print that calltrace anymore, printing a calltrace when booting
usually makes users think the kernel has a critical problem.

Signed-off-by: Hui Wang <hui.wang@canonical.com>

.github/ISSUE_TEMPLATE/bug_report.md

@@ -0,0 +1,34 @@
+---
+name: Bug report
+about: Create a report to help us fix your issue
+
+---
+
+**Is this the right place for my bug report?**
+This repository contains the Linux kernel used on the Raspberry Pi. If you believe that the issue you are seeing is kernel-related, this is the right place. If not, we have other repositories for the GPU firmware at [github.com/raspberrypi/firmware](https://github.com/raspberrypi/firmware) and Raspberry Pi userland applications at [github.com/raspberrypi/userland](https://github.com/raspberrypi/userland). If you have problems with the Raspbian distribution packages, report them in the [github.com/RPi-Distro/repo](https://github.com/RPi-Distro/repo). If you simply have a question, then [the Raspberry Pi forums](https://www.raspberrypi.org/forums) are the best place to ask it.
+
+**Describe the bug**
+Add a clear and concise description of what you think the bug is.
+
+**To reproduce**
+List the steps required to reproduce the issue.
+
+**Expected behaviour**
+Add a clear and concise description of what you expected to happen.
+
+**Actual behaviour**
+Add a clear and concise description of what actually happened.
+
+**System**
+ Copy and paste the results of the raspinfo command in to this section. Alternatively, copy and paste a pastebin link, or add answers to the following questions:
+
+* Which model of Raspberry Pi? e.g. Pi3B+, PiZeroW
+* Which OS and version (`cat /etc/rpi-issue`)?
+* Which firmware version (`vcgencmd version`)?
+* Which kernel version (`uname -a`)?
+
+**Logs**
+If applicable, add the relevant output from `dmesg` or similar.
+
+**Additional context**
+Add any other relevant context for the problem.

.gitignore

@@ -17,6 +17,7 @@
 *.c.[012]*.*
 *.dt.yaml
 *.dtb
+*.dtbo
 *.dtb.S
 *.dwo
 *.elf

Documentation/ABI/testing/sysfs-devices-system-cpu

@@ -486,6 +486,8 @@ What:		/sys/devices/system/cpu/vulnerabilities
 		/sys/devices/system/cpu/vulnerabilities/spec_store_bypass
 		/sys/devices/system/cpu/vulnerabilities/l1tf
 		/sys/devices/system/cpu/vulnerabilities/mds
+		/sys/devices/system/cpu/vulnerabilities/tsx_async_abort
+		/sys/devices/system/cpu/vulnerabilities/itlb_multihit
 Date:		January 2018
 Contact:	Linux kernel mailing list <linux-kernel@vger.kernel.org>
 Description:	Information about CPU vulnerabilities

Documentation/admin-guide/hw-vuln/index.rst

@@ -12,3 +12,5 @@ are configurable at compile, boot or run time.
    spectre
    l1tf
    mds
+   tsx_async_abort
+   multihit.rst

Documentation/admin-guide/hw-vuln/mds.rst

@@ -265,8 +265,11 @@ time with the option "mds=". The valid arguments for this option are:
 
   ============  =============================================================
 
-Not specifying this option is equivalent to "mds=full".
+Not specifying this option is equivalent to "mds=full". For processors
-
+that are affected by both TAA (TSX Asynchronous Abort) and MDS,
+specifying just "mds=off" without an accompanying "tsx_async_abort=off"
+will have no effect as the same mitigation is used for both
+vulnerabilities.
 
 Mitigation selection guide
 --------------------------

Documentation/admin-guide/hw-vuln/multihit.rst

@@ -0,0 +1,163 @@
+iTLB multihit
+=============
+
+iTLB multihit is an erratum where some processors may incur a machine check
+error, possibly resulting in an unrecoverable CPU lockup, when an
+instruction fetch hits multiple entries in the instruction TLB. This can
+occur when the page size is changed along with either the physical address
+or cache type. A malicious guest running on a virtualized system can
+exploit this erratum to perform a denial of service attack.
+
+
+Affected processors
+-------------------
+
+Variations of this erratum are present on most Intel Core and Xeon processor
+models. The erratum is not present on:
+
+   - non-Intel processors
+
+   - Some Atoms (Airmont, Bonnell, Goldmont, GoldmontPlus, Saltwell, Silvermont)
+
+   - Intel processors that have the PSCHANGE_MC_NO bit set in the
+     IA32_ARCH_CAPABILITIES MSR.
+
+
+Related CVEs
+------------
+
+The following CVE entry is related to this issue:
+
+   ==============  =================================================
+   CVE-2018-12207  Machine Check Error Avoidance on Page Size Change
+   ==============  =================================================
+
+
+Problem
+-------
+
+Privileged software, including OS and virtual machine managers (VMM), are in
+charge of memory management. A key component in memory management is the control
+of the page tables. Modern processors use virtual memory, a technique that creates
+the illusion of a very large memory for processors. This virtual space is split
+into pages of a given size. Page tables translate virtual addresses to physical
+addresses.
+
+To reduce latency when performing a virtual to physical address translation,
+processors include a structure, called TLB, that caches recent translations.
+There are separate TLBs for instruction (iTLB) and data (dTLB).
+
+Under this errata, instructions are fetched from a linear address translated
+using a 4 KB translation cached in the iTLB. Privileged software modifies the
+paging structure so that the same linear address using large page size (2 MB, 4
+MB, 1 GB) with a different physical address or memory type.  After the page
+structure modification but before the software invalidates any iTLB entries for
+the linear address, a code fetch that happens on the same linear address may
+cause a machine-check error which can result in a system hang or shutdown.
+
+
+Attack scenarios
+----------------
+
+Attacks against the iTLB multihit erratum can be mounted from malicious
+guests in a virtualized system.
+
+
+iTLB multihit system information
+--------------------------------
+
+The Linux kernel provides a sysfs interface to enumerate the current iTLB
+multihit status of the system:whether the system is vulnerable and which
+mitigations are active. The relevant sysfs file is:
+
+/sys/devices/system/cpu/vulnerabilities/itlb_multihit
+
+The possible values in this file are:
+
+.. list-table::
+
+     * - Not affected
+       - The processor is not vulnerable.
+     * - KVM: Mitigation: Split huge pages
+       - Software changes mitigate this issue.
+     * - KVM: Vulnerable
+       - The processor is vulnerable, but no mitigation enabled
+
+
+Enumeration of the erratum
+--------------------------------
+
+A new bit has been allocated in the IA32_ARCH_CAPABILITIES (PSCHANGE_MC_NO) msr
+and will be set on CPU's which are mitigated against this issue.
+
+   =======================================   ===========   ===============================
+   IA32_ARCH_CAPABILITIES MSR                Not present   Possibly vulnerable,check model
+   IA32_ARCH_CAPABILITIES[PSCHANGE_MC_NO]    '0'           Likely vulnerable,check model
+   IA32_ARCH_CAPABILITIES[PSCHANGE_MC_NO]    '1'           Not vulnerable
+   =======================================   ===========   ===============================
+
+
+Mitigation mechanism
+-------------------------
+
+This erratum can be mitigated by restricting the use of large page sizes to
+non-executable pages.  This forces all iTLB entries to be 4K, and removes
+the possibility of multiple hits.
+
+In order to mitigate the vulnerability, KVM initially marks all huge pages
+as non-executable. If the guest attempts to execute in one of those pages,
+the page is broken down into 4K pages, which are then marked executable.
+
+If EPT is disabled or not available on the host, KVM is in control of TLB
+flushes and the problematic situation cannot happen.  However, the shadow
+EPT paging mechanism used by nested virtualization is vulnerable, because
+the nested guest can trigger multiple iTLB hits by modifying its own
+(non-nested) page tables.  For simplicity, KVM will make large pages
+non-executable in all shadow paging modes.
+
+Mitigation control on the kernel command line and KVM - module parameter
+------------------------------------------------------------------------
+
+The KVM hypervisor mitigation mechanism for marking huge pages as
+non-executable can be controlled with a module parameter "nx_huge_pages=".
+The kernel command line allows to control the iTLB multihit mitigations at
+boot time with the option "kvm.nx_huge_pages=".
+
+The valid arguments for these options are:
+
+  ==========  ================================================================
+  force       Mitigation is enabled. In this case, the mitigation implements
+              non-executable huge pages in Linux kernel KVM module. All huge
+              pages in the EPT are marked as non-executable.
+              If a guest attempts to execute in one of those pages, the page is
+              broken down into 4K pages, which are then marked executable.
+
+  off	      Mitigation is disabled.
+
+  auto        Enable mitigation only if the platform is affected and the kernel
+              was not booted with the "mitigations=off" command line parameter.
+	      This is the default option.
+  ==========  ================================================================
+
+
+Mitigation selection guide
+--------------------------
+
+1. No virtualization in use
+^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+   The system is protected by the kernel unconditionally and no further
+   action is required.
+
+2. Virtualization with trusted guests
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+   If the guest comes from a trusted source, you may assume that the guest will
+   not attempt to maliciously exploit these errata and no further action is
+   required.
+
+3. Virtualization with untrusted guests
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+   If the guest comes from an untrusted source, the guest host kernel will need
+   to apply iTLB multihit mitigation via the kernel command line or kvm
+   module parameter.

Documentation/admin-guide/hw-vuln/tsx_async_abort.rst

@@ -0,0 +1,279 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+TAA - TSX Asynchronous Abort
+======================================
+
+TAA is a hardware vulnerability that allows unprivileged speculative access to
+data which is available in various CPU internal buffers by using asynchronous
+aborts within an Intel TSX transactional region.
+
+Affected processors
+-------------------
+
+This vulnerability only affects Intel processors that support Intel
+Transactional Synchronization Extensions (TSX) when the TAA_NO bit (bit 8)
+is 0 in the IA32_ARCH_CAPABILITIES MSR.  On processors where the MDS_NO bit
+(bit 5) is 0 in the IA32_ARCH_CAPABILITIES MSR, the existing MDS mitigations
+also mitigate against TAA.
+
+Whether a processor is affected or not can be read out from the TAA
+vulnerability file in sysfs. See :ref:`tsx_async_abort_sys_info`.
+
+Related CVEs
+------------
+
+The following CVE entry is related to this TAA issue:
+
+   ==============  =====  ===================================================
+   CVE-2019-11135  TAA    TSX Asynchronous Abort (TAA) condition on some
+                          microprocessors utilizing speculative execution may
+                          allow an authenticated user to potentially enable
+                          information disclosure via a side channel with
+                          local access.
+   ==============  =====  ===================================================
+
+Problem
+-------
+
+When performing store, load or L1 refill operations, processors write
+data into temporary microarchitectural structures (buffers). The data in
+those buffers can be forwarded to load operations as an optimization.
+
+Intel TSX is an extension to the x86 instruction set architecture that adds
+hardware transactional memory support to improve performance of multi-threaded
+software. TSX lets the processor expose and exploit concurrency hidden in an
+application due to dynamically avoiding unnecessary synchronization.
+
+TSX supports atomic memory transactions that are either committed (success) or
+aborted. During an abort, operations that happened within the transactional region
+are rolled back. An asynchronous abort takes place, among other options, when a
+different thread accesses a cache line that is also used within the transactional
+region when that access might lead to a data race.
+
+Immediately after an uncompleted asynchronous abort, certain speculatively
+executed loads may read data from those internal buffers and pass it to dependent
+operations. This can be then used to infer the value via a cache side channel
+attack.
+
+Because the buffers are potentially shared between Hyper-Threads cross
+Hyper-Thread attacks are possible.
+
+The victim of a malicious actor does not need to make use of TSX. Only the
+attacker needs to begin a TSX transaction and raise an asynchronous abort
+which in turn potenitally leaks data stored in the buffers.
+
+More detailed technical information is available in the TAA specific x86
+architecture section: :ref:`Documentation/x86/tsx_async_abort.rst <tsx_async_abort>`.
+
+
+Attack scenarios
+----------------
+
+Attacks against the TAA vulnerability can be implemented from unprivileged
+applications running on hosts or guests.
+
+As for MDS, the attacker has no control over the memory addresses that can
+be leaked. Only the victim is responsible for bringing data to the CPU. As
+a result, the malicious actor has to sample as much data as possible and
+then postprocess it to try to infer any useful information from it.
+
+A potential attacker only has read access to the data. Also, there is no direct
+privilege escalation by using this technique.
+
+
+.. _tsx_async_abort_sys_info:
+
+TAA system information
+-----------------------
+
+The Linux kernel provides a sysfs interface to enumerate the current TAA status
+of mitigated systems. The relevant sysfs file is:
+
+/sys/devices/system/cpu/vulnerabilities/tsx_async_abort
+
+The possible values in this file are:
+
+.. list-table::
+
+   * - 'Vulnerable'
+     - The CPU is affected by this vulnerability and the microcode and kernel mitigation are not applied.
+   * - 'Vulnerable: Clear CPU buffers attempted, no microcode'
+     - The system tries to clear the buffers but the microcode might not support the operation.
+   * - 'Mitigation: Clear CPU buffers'
+     - The microcode has been updated to clear the buffers. TSX is still enabled.
+   * - 'Mitigation: TSX disabled'
+     - TSX is disabled.
+   * - 'Not affected'
+     - The CPU is not affected by this issue.
+
+.. _ucode_needed:
+
+Best effort mitigation mode
+^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+If the processor is vulnerable, but the availability of the microcode-based
+mitigation mechanism is not advertised via CPUID the kernel selects a best
+effort mitigation mode.  This mode invokes the mitigation instructions
+without a guarantee that they clear the CPU buffers.
+
+This is done to address virtualization scenarios where the host has the
+microcode update applied, but the hypervisor is not yet updated to expose the
+CPUID to the guest. If the host has updated microcode the protection takes
+effect; otherwise a few CPU cycles are wasted pointlessly.
+
+The state in the tsx_async_abort sysfs file reflects this situation
+accordingly.
+
+
+Mitigation mechanism
+--------------------
+
+The kernel detects the affected CPUs and the presence of the microcode which is
+required. If a CPU is affected and the microcode is available, then the kernel
+enables the mitigation by default.
+
+
+The mitigation can be controlled at boot time via a kernel command line option.
+See :ref:`taa_mitigation_control_command_line`.
+
+.. _virt_mechanism:
+
+Virtualization mitigation
+^^^^^^^^^^^^^^^^^^^^^^^^^
+
+Affected systems where the host has TAA microcode and TAA is mitigated by
+having disabled TSX previously, are not vulnerable regardless of the status
+of the VMs.
+
+In all other cases, if the host either does not have the TAA microcode or
+the kernel is not mitigated, the system might be vulnerable.
+
+
+.. _taa_mitigation_control_command_line:
+
+Mitigation control on the kernel command line
+---------------------------------------------
+
+The kernel command line allows to control the TAA mitigations at boot time with
+the option "tsx_async_abort=". The valid arguments for this option are:
+
+  ============  =============================================================
+  off		This option disables the TAA mitigation on affected platforms.
+                If the system has TSX enabled (see next parameter) and the CPU
+                is affected, the system is vulnerable.
+
+  full	        TAA mitigation is enabled. If TSX is enabled, on an affected
+                system it will clear CPU buffers on ring transitions. On
+                systems which are MDS-affected and deploy MDS mitigation,
+                TAA is also mitigated. Specifying this option on those
+                systems will have no effect.
+
+  full,nosmt    The same as tsx_async_abort=full, with SMT disabled on
+                vulnerable CPUs that have TSX enabled. This is the complete
+                mitigation. When TSX is disabled, SMT is not disabled because
+                CPU is not vulnerable to cross-thread TAA attacks.
+  ============  =============================================================
+
+Not specifying this option is equivalent to "tsx_async_abort=full". For
+processors that are affected by both TAA and MDS, specifying just
+"tsx_async_abort=off" without an accompanying "mds=off" will have no
+effect as the same mitigation is used for both vulnerabilities.
+
+The kernel command line also allows to control the TSX feature using the
+parameter "tsx=" on CPUs which support TSX control. MSR_IA32_TSX_CTRL is used
+to control the TSX feature and the enumeration of the TSX feature bits (RTM
+and HLE) in CPUID.
+
+The valid options are:
+
+  ============  =============================================================
+  off		Disables TSX on the system.
+
+                Note that this option takes effect only on newer CPUs which are
+                not vulnerable to MDS, i.e., have MSR_IA32_ARCH_CAPABILITIES.MDS_NO=1
+                and which get the new IA32_TSX_CTRL MSR through a microcode
+                update. This new MSR allows for the reliable deactivation of
+                the TSX functionality.
+
+  on		Enables TSX.
+
+                Although there are mitigations for all known security
+                vulnerabilities, TSX has been known to be an accelerator for
+                several previous speculation-related CVEs, and so there may be
+                unknown security risks associated with leaving it enabled.
+
+  auto		Disables TSX if X86_BUG_TAA is present, otherwise enables TSX
+                on the system.
+  ============  =============================================================
+
+Not specifying this option is equivalent to "tsx=off".
+
+The following combinations of the "tsx_async_abort" and "tsx" are possible. For
+affected platforms tsx=auto is equivalent to tsx=off and the result will be:
+
+  =========  ==========================   =========================================
+  tsx=on     tsx_async_abort=full         The system will use VERW to clear CPU
+                                          buffers. Cross-thread attacks are still
+					  possible on SMT machines.
+  tsx=on     tsx_async_abort=full,nosmt   As above, cross-thread attacks on SMT
+                                          mitigated.
+  tsx=on     tsx_async_abort=off          The system is vulnerable.
+  tsx=off    tsx_async_abort=full         TSX might be disabled if microcode
+                                          provides a TSX control MSR. If so,
+					  system is not vulnerable.
+  tsx=off    tsx_async_abort=full,nosmt   Ditto
+  tsx=off    tsx_async_abort=off          ditto
+  =========  ==========================   =========================================
+
+
+For unaffected platforms "tsx=on" and "tsx_async_abort=full" does not clear CPU
+buffers.  For platforms without TSX control (MSR_IA32_ARCH_CAPABILITIES.MDS_NO=0)
+"tsx" command line argument has no effect.
+
+For the affected platforms below table indicates the mitigation status for the
+combinations of CPUID bit MD_CLEAR and IA32_ARCH_CAPABILITIES MSR bits MDS_NO
+and TSX_CTRL_MSR.
+
+  =======  =========  =============  ========================================
+  MDS_NO   MD_CLEAR   TSX_CTRL_MSR   Status
+  =======  =========  =============  ========================================
+    0          0            0        Vulnerable (needs microcode)
+    0          1            0        MDS and TAA mitigated via VERW
+    1          1            0        MDS fixed, TAA vulnerable if TSX enabled
+                                     because MD_CLEAR has no meaning and
+                                     VERW is not guaranteed to clear buffers
+    1          X            1        MDS fixed, TAA can be mitigated by
+                                     VERW or TSX_CTRL_MSR
+  =======  =========  =============  ========================================
+
+Mitigation selection guide
+--------------------------
+
+1. Trusted userspace and guests
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+If all user space applications are from a trusted source and do not execute
+untrusted code which is supplied externally, then the mitigation can be
+disabled. The same applies to virtualized environments with trusted guests.
+
+
+2. Untrusted userspace and guests
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+If there are untrusted applications or guests on the system, enabling TSX
+might allow a malicious actor to leak data from the host or from other
+processes running on the same physical core.
+
+If the microcode is available and the TSX is disabled on the host, attacks
+are prevented in a virtualized environment as well, even if the VMs do not
+explicitly enable the mitigation.
+
+
+.. _taa_default_mitigations:
+
+Default mitigations
+-------------------
+
+The kernel's default action for vulnerable processors is:
+
+  - Deploy TSX disable mitigation (tsx_async_abort=full tsx=off).

Documentation/admin-guide/kernel-parameters.txt

@@ -2040,6 +2040,25 @@
 			KVM MMU at runtime.
 			Default is 0 (off)
 
+	kvm.nx_huge_pages=
+			[KVM] Controls the software workaround for the
+			X86_BUG_ITLB_MULTIHIT bug.
+			force	: Always deploy workaround.
+			off	: Never deploy workaround.
+			auto    : Deploy workaround based on the presence of
+				  X86_BUG_ITLB_MULTIHIT.
+
+			Default is 'auto'.
+
+			If the software workaround is enabled for the host,
+			guests do need not to enable it for nested guests.
+
+	kvm.nx_huge_pages_recovery_ratio=
+			[KVM] Controls how many 4KiB pages are periodically zapped
+			back to huge pages.  0 disables the recovery, otherwise if
+			the value is N KVM will zap 1/Nth of the 4KiB pages every
+			minute.  The default is 60.
+
 	kvm-amd.nested=	[KVM,AMD] Allow nested virtualization in KVM/SVM.
 			Default is 1 (enabled)
 
@@ -2430,6 +2449,12 @@
 				     SMT on vulnerable CPUs
 			off        - Unconditionally disable MDS mitigation
 
+			On TAA-affected machines, mds=off can be prevented by
+			an active TAA mitigation as both vulnerabilities are
+			mitigated with the same mechanism so in order to disable
+			this mitigation, you need to specify tsx_async_abort=off
+			too.
+
 			Not specifying this option is equivalent to
 			mds=full.
 
@@ -2612,6 +2637,13 @@
 					       ssbd=force-off [ARM64]
 					       l1tf=off [X86]
 					       mds=off [X86]
+					       tsx_async_abort=off [X86]
+					       kvm.nx_huge_pages=off [X86]
+
+				Exceptions:
+					       This does not have any effect on
+					       kvm.nx_huge_pages when
+					       kvm.nx_huge_pages=force.
 
 			auto (default)
 				Mitigate all CPU vulnerabilities, but leave SMT
@@ -2627,6 +2659,7 @@
 				be fully mitigated, even if it means losing SMT.
 				Equivalent to: l1tf=flush,nosmt [X86]
 					       mds=full,nosmt [X86]
+					       tsx_async_abort=full,nosmt [X86]
 
 	mminit_loglevel=
 			[KNL] When CONFIG_DEBUG_MEMORY_INIT is set, this
@@ -4813,6 +4846,76 @@
 			interruptions from clocksource watchdog are not
 			acceptable).
 
+	tsx=		[X86] Control Transactional Synchronization
+			Extensions (TSX) feature in Intel processors that
+			support TSX control.
+
+			This parameter controls the TSX feature. The options are:
+
+			on	- Enable TSX on the system. Although there are
+				mitigations for all known security vulnerabilities,
+				TSX has been known to be an accelerator for
+				several previous speculation-related CVEs, and
+				so there may be unknown	security risks associated
+				with leaving it enabled.
+
+			off	- Disable TSX on the system. (Note that this
+				option takes effect only on newer CPUs which are
+				not vulnerable to MDS, i.e., have
+				MSR_IA32_ARCH_CAPABILITIES.MDS_NO=1 and which get
+				the new IA32_TSX_CTRL MSR through a microcode
+				update. This new MSR allows for the reliable
+				deactivation of the TSX functionality.)
+
+			auto	- Disable TSX if X86_BUG_TAA is present,
+				  otherwise enable TSX on the system.
+
+			Not specifying this option is equivalent to tsx=off.
+
+			See Documentation/admin-guide/hw-vuln/tsx_async_abort.rst
+			for more details.
+
+	tsx_async_abort= [X86,INTEL] Control mitigation for the TSX Async
+			Abort (TAA) vulnerability.
+
+			Similar to Micro-architectural Data Sampling (MDS)
+			certain CPUs that support Transactional
+			Synchronization Extensions (TSX) are vulnerable to an
+			exploit against CPU internal buffers which can forward
+			information to a disclosure gadget under certain
+			conditions.
+
+			In vulnerable processors, the speculatively forwarded
+			data can be used in a cache side channel attack, to
+			access data to which the attacker does not have direct
+			access.
+
+			This parameter controls the TAA mitigation.  The
+			options are:
+
+			full       - Enable TAA mitigation on vulnerable CPUs
+				     if TSX is enabled.
+
+			full,nosmt - Enable TAA mitigation and disable SMT on
+				     vulnerable CPUs. If TSX is disabled, SMT
+				     is not disabled because CPU is not
+				     vulnerable to cross-thread TAA attacks.
+			off        - Unconditionally disable TAA mitigation
+
+			On MDS-affected machines, tsx_async_abort=off can be
+			prevented by an active MDS mitigation as both vulnerabilities
+			are mitigated with the same mechanism so in order to disable
+			this mitigation, you need to specify mds=off too.
+
+			Not specifying this option is equivalent to
+			tsx_async_abort=full.  On CPUs which are MDS affected
+			and deploy MDS mitigation, TAA mitigation is not
+			required and doesn't provide any additional
+			mitigation.
+
+			For details see:
+			Documentation/admin-guide/hw-vuln/tsx_async_abort.rst
+
 	turbografx.map[2|3]=	[HW,JOY]
 			TurboGraFX parallel port interface
 			Format:
@@ -4963,13 +5066,13 @@
 			Flags is a set of characters, each corresponding
 			to a common usb-storage quirk flag as follows:
 				a = SANE_SENSE (collect more than 18 bytes
-					of sense data);
+					of sense data, not on uas);
 				b = BAD_SENSE (don't collect more than 18
-					bytes of sense data);
+					bytes of sense data, not on uas);
 				c = FIX_CAPACITY (decrease the reported
 					device capacity by one sector);
 				d = NO_READ_DISC_INFO (don't use
-					READ_DISC_INFO command);
+					READ_DISC_INFO command, not on uas);
 				e = NO_READ_CAPACITY_16 (don't use
 					READ_CAPACITY_16 command);
 				f = NO_REPORT_OPCODES (don't use report opcodes
@@ -4984,17 +5087,18 @@
 				j = NO_REPORT_LUNS (don't use report luns
 					command, uas only);
 				l = NOT_LOCKABLE (don't try to lock and
-					unlock ejectable media);
+					unlock ejectable media, not on uas);
 				m = MAX_SECTORS_64 (don't transfer more
-					than 64 sectors = 32 KB at a time);
+					than 64 sectors = 32 KB at a time,
+					not on uas);
 				n = INITIAL_READ10 (force a retry of the
-					initial READ(10) command);
+					initial READ(10) command, not on uas);
 				o = CAPACITY_OK (accept the capacity
-					reported by the device);
+					reported by the device, not on uas);
 				p = WRITE_CACHE (the device cache is ON
-					by default);
+					by default, not on uas);
 				r = IGNORE_RESIDUE (the device reports
-					bogus residue values);
+					bogus residue values, not on uas);
 				s = SINGLE_LUN (the device has only one
 					Logical Unit);
 				t = NO_ATA_1X (don't allow ATA(12) and ATA(16)
@@ -5003,7 +5107,8 @@
 				w = NO_WP_DETECT (don't test whether the
 					medium is write-protected).
 				y = ALWAYS_SYNC (issue a SYNCHRONIZE_CACHE
-					even if the device claims no cache)
+					even if the device claims no cache,
+					not on uas)
 			Example: quirks=0419:aaf5:rl,0421:0433:rc
 
 	user_debug=	[KNL,ARM]
@@ -5267,6 +5372,10 @@
 				the unplug protocol
 			never -- do not unplug even if version check succeeds
 
+	xen_legacy_crash	[X86,XEN]
+			Crash from Xen panic notifier, without executing late
+			panic() code such as dumping handler.
+
 	xen_nopvspin	[X86,XEN]
 			Disables the ticketlock slowpath using Xen PV
 			optimizations.

Documentation/arm64/silicon-errata.rst

@@ -91,6 +91,11 @@ stable kernels.
 | ARM            | MMU-500         | #841119,826419  | N/A                         |
 +----------------+-----------------+-----------------+-----------------------------+
 +----------------+-----------------+-----------------+-----------------------------+
+| Broadcom       | Brahma-B53      | N/A             | ARM64_ERRATUM_845719        |
++----------------+-----------------+-----------------+-----------------------------+
+| Broadcom       | Brahma-B53      | N/A             | ARM64_ERRATUM_843419        |
++----------------+-----------------+-----------------+-----------------------------+
++----------------+-----------------+-----------------+-----------------------------+
 | Cavium         | ThunderX ITS    | #22375,24313    | CAVIUM_ERRATUM_22375        |
 +----------------+-----------------+-----------------+-----------------------------+
 | Cavium         | ThunderX ITS    | #23144          | CAVIUM_ERRATUM_23144        |
@@ -107,6 +112,8 @@ stable kernels.
 +----------------+-----------------+-----------------+-----------------------------+
 | Cavium         | ThunderX2 SMMUv3| #126            | N/A                         |
 +----------------+-----------------+-----------------+-----------------------------+
+| Cavium         | ThunderX2 Core  | #219            | CAVIUM_TX2_ERRATUM_219      |
++----------------+-----------------+-----------------+-----------------------------+
 +----------------+-----------------+-----------------+-----------------------------+
 | Freescale/NXP  | LS2080A/LS1043A | A-008585        | FSL_ERRATUM_A008585         |
 +----------------+-----------------+-----------------+-----------------------------+
@@ -122,7 +129,7 @@ stable kernels.
 +----------------+-----------------+-----------------+-----------------------------+
 | Qualcomm Tech. | Kryo/Falkor v1  | E1003           | QCOM_FALKOR_ERRATUM_1003    |
 +----------------+-----------------+-----------------+-----------------------------+
-| Qualcomm Tech. | Falkor v1       | E1009           | QCOM_FALKOR_ERRATUM_1009    |
+| Qualcomm Tech. | Kryo/Falkor v1  | E1009           | QCOM_FALKOR_ERRATUM_1009    |
 +----------------+-----------------+-----------------+-----------------------------+
 | Qualcomm Tech. | QDF2400 ITS     | E0065           | QCOM_QDF2400_ERRATUM_0065   |
 +----------------+-----------------+-----------------+-----------------------------+

Documentation/devicetree/bindings/hwmon/rpi-poe-fan.txt

@@ -0,0 +1,55 @@
+Bindings for the Raspberry Pi PoE HAT fan
+
+Required properties:
+- compatible	: "raspberrypi,rpi-poe-fan"
+- firmware	: Reference to the RPi firmware device node
+- pwms		: the PWM that is used to control the PWM fan
+- cooling-levels      : PWM duty cycle values in a range from 0 to 255
+			which correspond to thermal cooling states
+
+Example:
+	fan0: rpi-poe-fan@0 {
+		compatible = "raspberrypi,rpi-poe-fan";
+		firmware = <&firmware>;
+		cooling-min-state = <0>;
+		cooling-max-state = <3>;
+		#cooling-cells = <2>;
+		cooling-levels = <0 50 150 255>;
+		status = "okay";
+	};
+
+	thermal-zones {
+		cpu_thermal: cpu-thermal {
+			trips {
+				threshold: trip-point@0 {
+					temperature = <45000>;
+					hysteresis = <5000>;
+					type = "active";
+				};
+				target: trip-point@1 {
+					temperature = <50000>;
+					hysteresis = <2000>;
+					type = "active";
+				};
+				cpu_hot: cpu_hot@0 {
+					temperature = <55000>;
+					hysteresis = <2000>;
+					type = "active";
+				};
+			};
+			cooling-maps {
+				map0 {
+					trip = <&threshold>;
+					cooling-device = <&fan0 0 1>;
+				};
+				map1 {
+					trip = <&target>;
+					cooling-device = <&fan0 1 2>;
+				};
+				map2 {
+					trip = <&cpu_hot>;
+					cooling-device = <&fan0 2 3>;
+				};
+			};
+		};
+	};

Documentation/devicetree/bindings/media/bcm2835-unicam.txt

@@ -0,0 +1,85 @@
+Broadcom BCM283x Camera Interface (Unicam)
+------------------------------------------
+
+The Unicam block on BCM283x SoCs is the receiver for either
+CSI-2 or CCP2 data from image sensors or similar devices.
+
+The main platform using this SoC is the Raspberry Pi family of boards.
+On the Pi the VideoCore firmware can also control this hardware block,
+and driving it from two different processors will cause issues.
+To avoid this, the firmware checks the device tree configuration
+during boot. If it finds device tree nodes called csi0 or csi1 then
+it will stop the firmware accessing the block, and it can then
+safely be used via the device tree binding.
+
+Required properties:
+===================
+- compatible	: must be "brcm,bcm2835-unicam".
+- reg		: physical base address and length of the register sets for the
+		  device.
+- interrupts	: should contain the IRQ line for this Unicam instance.
+- clocks	: list of clock specifiers, corresponding to entries in
+		  clock-names property.
+- clock-names	: must contain an "lp" entry, matching entries in the
+		  clocks property.
+
+Unicam supports a single port node. It should contain one 'port' child node
+with child 'endpoint' node. Please refer to the bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Within the endpoint node the "remote-endpoint" and "data-lanes" properties
+are mandatory.
+Data lane reordering is not supported so the data lanes must be in order,
+starting at 1. The number of data lanes should represent the number of
+usable lanes for the hardware block. That may be limited by either the SoC or
+how the platform presents the interface, and the lower value must be used.
+
+Lane reordering is not supported on the clock lane either, so the optional
+property "clock-lane" will implicitly be <0>.
+Similarly lane inversion is not supported, therefore "lane-polarities" will
+implicitly be <0 0 0 0 0>.
+Neither of these values will be checked.
+
+Example:
+	csi1: csi1@7e801000 {
+		compatible = "brcm,bcm2835-unicam";
+		reg = <0x7e801000 0x800>,
+		      <0x7e802004 0x4>;
+		interrupts = <2 7>;
+		clocks = <&clocks BCM2835_CLOCK_CAM1>;
+		clock-names = "lp";
+
+		port {
+			csi1_ep: endpoint {
+				remote-endpoint = <&tc358743_0>;
+				data-lanes = <1 2>;
+			};
+		};
+	};
+
+	i2c0: i2c@7e205000 {
+		tc358743: csi-hdmi-bridge@0f {
+			compatible = "toshiba,tc358743";
+			reg = <0x0f>;
+
+			clocks = <&tc358743_clk>;
+			clock-names = "refclk";
+
+			tc358743_clk: bridge-clk {
+				compatible = "fixed-clock";
+				#clock-cells = <0>;
+				clock-frequency = <27000000>;
+			};
+
+			port {
+				tc358743_0: endpoint {
+					remote-endpoint = <&csi1_ep>;
+					clock-lanes = <0>;
+					data-lanes = <1 2>;
+					clock-noncontinuous;
+					link-frequencies =
+						/bits/ 64 <297000000>;
+				};
+			};
+		};
+	};

Documentation/devicetree/bindings/media/i2c/imx219.txt

@@ -0,0 +1,59 @@
+* Sony 1/4.0-Inch 8Mpixel CMOS Digital Image Sensor
+
+The Sony imx219 is a 1/4.0-inch CMOS active pixel digital image sensor with
+an active array size of 3280H x 2464V. It is programmable through I2C
+interface. The I2C address is fixed to 0x10 as per sensor data sheet.
+Image data is sent through MIPI CSI-2, which is configured as either 2 or 4
+data lanes.
+
+Required Properties:
+- compatible: value should be "sony,imx219" for imx219 sensor
+- reg: I2C bus address of the device
+- clocks: reference to the xclk input clock.
+- clock-names: should be "xclk".
+- DOVDD-supply: Digital I/O voltage supply, 1.8 volts
+- AVDD-supply: Analog voltage supply, 2.8 volts
+- DVDD-supply: Digital core voltage supply, 1.2 volts
+
+Optional Properties:
+- xclr-gpios: reference to the GPIO connected to the xclr pin, if any. Must be
+	      released after all supplies are applied.
+	      This is an active high signal to the imx219.
+
+The imx219 device node should contain one 'port' child node with
+an 'endpoint' subnode. For further reading on port node refer to
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Endpoint node required properties for CSI-2 connection are:
+- remote-endpoint: a phandle to the bus receiver's endpoint node.
+- clock-lanes: should be set to <0> (clock lane on hardware lane 0)
+- data-lanes: should be set to <1 2>, or  <1 2 3 4> (two or four lane CSI-2
+  supported)
+
+Example:
+	sensor@10 {
+		compatible = "sony,imx219";
+		reg = <0x10>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&imx219_clk>;
+		clock-names = "xclk";
+		xclr-gpios = <&gpio_sensor 0 0>;
+		DOVDD-supply = <&vgen4_reg>; /* 1.8v */
+		AVDD-supply = <&vgen3_reg>;  /* 2.8v */
+		DVDD-supply = <&vgen2_reg>;  /* 1.2v */
+
+		imx219_clk: camera-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <24000000>;
+		};
+
+		port {
+			sensor_out: endpoint {
+				remote-endpoint = <&csiss_in>;
+				clock-lanes = <0>;
+				data-lanes = <1 2>;
+			};
+		};
+	};

Documentation/devicetree/bindings/media/i2c/irs1125.txt

@@ -0,0 +1,48 @@
+* Infineon irs1125 time of flight sensor
+
+The Infineon irs1125 is a time of flight digital image sensor with
+an active array size of 352H x 286V. It is programmable through I2C
+interface. The I2C address defaults to 0x3D, but can be reconfigured
+to address 0x3C or 0x41 via I2C commands. Image data is sent through
+MIPI CSI-2, which is configured as either 1 or 2 data lanes.
+
+Required Properties:
+- compatible: value should be "infineon,irs1125" for irs1125 sensor
+- reg: I2C bus address of the device
+- clocks: reference to the xclk input clock.
+- pwdn-gpios: reference to the GPIO connected to the reset pin.
+	      This is an active low signal to the iirs1125.
+
+The irs1125 device node should contain one 'port' child node with
+an 'endpoint' subnode. For further reading on port node refer to
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Endpoint node required properties for CSI-2 connection are:
+- remote-endpoint: a phandle to the bus receiver's endpoint node.
+- clock-lanes: should be set to <0> (clock lane on hardware lane 0)
+- data-lanes: should be set to <1> or <1 2> (one or two lane CSI-2
+  supported)
+
+Example:
+	sensor@10 {
+		compatible = "infineon,irs1125";
+		reg = <0x3D>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&irs1125_clk>;
+		pwdn-gpios = <&gpio 5 0>;
+
+		irs1125_clk: camera-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <26000000>;
+		};
+
+		port {
+			sensor_out: endpoint {
+				remote-endpoint = <&csiss_in>;
+				clock-lanes = <0>;
+				data-lanes = <1 2>;
+			};
+		};
+	};

Documentation/devicetree/bindings/media/i2c/ov5647.txt

@@ -10,6 +10,9 @@ Required properties:
 - reg			: I2C slave address of the sensor.
 - clocks		: Reference to the xclk clock.
 
+Optional Properties:
+- pwdn-gpios: reference to the GPIO connected to the pwdn pin, if any.
+
 The common video interfaces bindings (see video-interfaces.txt) should be
 used to specify link to the image data receiver. The OV5647 device
 node should contain one 'port' child node with an 'endpoint' subnode.
@@ -26,6 +29,7 @@ Example:
 			compatible = "ovti,ov5647";
 			reg = <0x36>;
 			clocks = <&camera_clk>;
+			pwdn-gpios = <&pioE 29 GPIO_ACTIVE_HIGH>;
 			port {
 				camera_1: endpoint {
 					remote-endpoint = <&csi1_ep1>;

Documentation/devicetree/bindings/misc/brcm,bcm2835-smi-dev.txt

@@ -0,0 +1,17 @@
+* Broadcom BCM2835 SMI character device driver.
+
+SMI or secondary memory interface is a peripheral specific to certain Broadcom
+SOCs, and is helpful for talking to things like parallel-interface displays
+and NAND flashes (in fact, most things with a parallel register interface).
+
+This driver adds a character device which provides a user-space interface to
+an instance of the SMI driver.
+
+Required properties:
+- compatible: "brcm,bcm2835-smi-dev"
+- smi_handle: a phandle to the smi node.
+
+Optional properties:
+- None.
+
+

Documentation/devicetree/bindings/misc/brcm,bcm2835-smi.txt

@@ -0,0 +1,48 @@
+* Broadcom BCM2835 SMI driver.
+
+SMI or secondary memory interface is a peripheral specific to certain Broadcom
+SOCs, and is helpful for talking to things like parallel-interface displays
+and NAND flashes (in fact, most things with a parallel register interface).
+
+Required properties:
+- compatible: "brcm,bcm2835-smi"
+- reg: Should contain location and length of SMI registers and SMI clkman regs
+- interrupts: *the* SMI interrupt.
+- pinctrl-names: should be "default".
+- pinctrl-0: the phandle of the gpio pin node.
+- brcm,smi-clock-source: the clock source for clkman
+- brcm,smi-clock-divisor: the integer clock divisor for clkman
+- dmas: the dma controller phandle and the DREQ number (4 on a 2835)
+- dma-names: the name used by the driver to request its channel.
+  Should be "rx-tx".
+
+Optional properties:
+- None.
+
+Examples:
+
+8 data pin configuration:
+
+smi: smi@7e600000 {
+	compatible = "brcm,bcm2835-smi";
+	reg = <0x7e600000 0x44>, <0x7e1010b0 0x8>;
+	interrupts = <2 16>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&smi_pins>;
+	brcm,smi-clock-source = <6>;
+	brcm,smi-clock-divisor = <4>;
+	dmas = <&dma 4>;
+	dma-names = "rx-tx";
+
+	status = "okay";
+};
+
+smi_pins: smi_pins {
+	brcm,pins = <2 3 4 5 6 7 8 9 10 11 12 13 14 15>;
+	/* Alt 1: SMI */
+	brcm,function = <5 5 5 5 5 5 5 5 5 5 5 5 5 5>;
+	/* /CS, /WE and /OE are pulled high, as they are
+	   generally active low signals */
+	brcm,pull = <2 2 2 2 2 2 0 0 0 0 0 0 0 0>;
+};
+

Documentation/devicetree/bindings/net/microchip,lan78xx.txt

@@ -14,6 +14,9 @@ Optional properties of the embedded PHY:
 - microchip,led-modes: a 0..4 element vector, with each element configuring
   the operating mode of an LED. Omitted LEDs are turned off. Allowed values
   are defined in "include/dt-bindings/net/microchip-lan78xx.h".
+- microchip,downshift-after: sets the number of failed auto-negotiation
+  attempts after which the link is downgraded from 1000BASE-T. Should be one of
+  2, 3, 4, 5 or 0, where 0 means never downshift.
 
 Example:
 

Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt

@@ -81,6 +81,12 @@ Optional properties:
 	Definition: Name of external front end module used. Some valid FEM names
 		    for example: "microsemi-lx5586", "sky85703-11"
 		    and "sky85803" etc.
+- qcom,snoc-host-cap-8bit-quirk:
+	Usage: Optional
+	Value type: <empty>
+	Definition: Quirk specifying that the firmware expects the 8bit version
+		    of the host capability QMI request
+
 
 Example (to supply PCI based wifi block details):
 

Documentation/devicetree/bindings/pci/brcmstb-pcie.txt

@@ -0,0 +1,59 @@
+Brcmstb PCIe Host Controller Device Tree Bindings
+
+Required Properties:
+- compatible
+  "brcm,bcm7425-pcie" -- for 7425 family MIPS-based SOCs.
+  "brcm,bcm7435-pcie" -- for 7435 family MIPS-based SOCs.
+  "brcm,bcm7445-pcie" -- for 7445 and later ARM based SOCs (not including
+      the 7278).
+  "brcm,bcm7278-pcie"  -- for 7278 family ARM-based SOCs.
+
+- reg -- the register start address and length for the PCIe reg block.
+- interrupts -- two interrupts are specified; the first interrupt is for
+     the PCI host controller and the second is for MSI if the built-in
+     MSI controller is to be used.
+- interrupt-names -- names of the interrupts (above): "pcie" and "msi".
+- #address-cells -- set to <3>.
+- #size-cells -- set to <2>.
+- #interrupt-cells: set to <1>.
+- interrupt-map-mask and interrupt-map, standard PCI properties to define the
+     mapping of the PCIe interface to interrupt numbers.
+- ranges: ranges for the PCI memory and I/O regions.
+- linux,pci-domain -- should be unique per host controller.
+
+Optional Properties:
+- clocks -- phandle of pcie clock.
+- clock-names -- set to "sw_pcie" if clocks is used.
+- dma-ranges -- Specifies the inbound memory mapping regions when
+     an "identity map" is not possible.
+- msi-controller -- this property is typically specified to have the
+     PCIe controller use its internal MSI controller.
+- msi-parent -- set to use an external MSI interrupt controller.
+- brcm,enable-ssc -- (boolean) indicates usage of spread-spectrum clocking.
+- max-link-speed --  (integer) indicates desired generation of link:
+     1 => 2.5 Gbps (gen1), 2 => 5.0 Gbps (gen2), 3 => 8.0 Gbps (gen3).
+
+Example Node:
+
+pcie0: pcie@f0460000 {
+		reg = <0x0 0xf0460000 0x0 0x9310>;
+		interrupts = <0x0 0x0 0x4>;
+		compatible = "brcm,bcm7445-pcie";
+		#address-cells = <3>;
+		#size-cells = <2>;
+		ranges = <0x02000000 0x00000000 0x00000000 0x00000000 0xc0000000 0x00000000 0x08000000
+			  0x02000000 0x00000000 0x08000000 0x00000000 0xc8000000 0x00000000 0x08000000>;
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 7>;
+		interrupt-map = <0 0 0 1 &intc 0 47 3
+				 0 0 0 2 &intc 0 48 3
+				 0 0 0 3 &intc 0 49 3
+				 0 0 0 4 &intc 0 50 3>;
+		clocks = <&sw_pcie0>;
+		clock-names = "sw_pcie";
+		msi-parent = <&pcie0>;  /* use PCIe's internal MSI controller */
+		msi-controller;         /* use PCIe's internal MSI controller */
+		brcm,ssc;
+		max-link-speed = <1>;
+		linux,pci-domain = <0>;
+	};

Documentation/devicetree/bindings/power/reset/gpio-poweroff.txt

@@ -31,6 +31,7 @@ Optional properties:
 - inactive-delay-ms: Delay (default 100) to wait after driving gpio inactive
 - timeout-ms: Time to wait before asserting a WARN_ON(1). If nothing is
               specified, 3000 ms is used.
+- export : Export the GPIO line to the sysfs system
 
 Examples:
 

Documentation/devicetree/bindings/serial/pl011.yaml

@@ -100,6 +100,12 @@ properties:
       - $ref: /schemas/types.yaml#/definitions/uint32
       - default: 3000
 
+  cts-event-workaround:
+    description:
+      Enables the (otherwise vendor-specific) workaround for the
+      CTS-induced TX lockup.
+    type: boolean
+
 required:
   - compatible
   - reg

Documentation/devicetree/bindings/sound/allwinner,sun4i-a10-spdif.yaml

@@ -70,7 +70,9 @@ allOf:
       properties:
         compatible:
           contains:
-            const: allwinner,sun8i-h3-spdif
+            enum:
+              - allwinner,sun8i-h3-spdif
+              - allwinner,sun50i-h6-spdif
 
     then:
       properties:

Documentation/devicetree/bindings/vendor-prefixes.txt

@@ -0,0 +1,463 @@
+Device tree binding vendor prefix registry.  Keep list in alphabetical order.
+
+This isn't an exhaustive list, but you should add new prefixes to it before
+using them to avoid name-space collisions.
+
+abilis	Abilis Systems
+abracon	Abracon Corporation
+actions	Actions Semiconductor Co., Ltd.
+active-semi	Active-Semi International Inc
+ad	Avionic Design GmbH
+adafruit	Adafruit Industries, LLC
+adapteva	Adapteva, Inc.
+adaptrum	Adaptrum, Inc.
+adh	AD Holdings Plc.
+adi	Analog Devices, Inc.
+advantech	Advantech Corporation
+aeroflexgaisler	Aeroflex Gaisler AB
+al	Annapurna Labs
+allo	Allo.com
+allwinner	Allwinner Technology Co., Ltd.
+alphascale	AlphaScale Integrated Circuits Systems, Inc.
+altr	Altera Corp.
+amarula	Amarula Solutions
+amazon	Amazon.com, Inc.
+amcc	Applied Micro Circuits Corporation (APM, formally AMCC)
+amd	Advanced Micro Devices (AMD), Inc.
+amediatech	Shenzhen Amediatech Technology Co., Ltd
+amlogic	Amlogic, Inc.
+ampire	Ampire Co., Ltd.
+ams	AMS AG
+amstaos	AMS-Taos Inc.
+analogix	Analogix Semiconductor, Inc.
+andestech	Andes Technology Corporation
+apm	Applied Micro Circuits Corporation (APM)
+aptina	Aptina Imaging
+arasan	Arasan Chip Systems
+archermind ArcherMind Technology (Nanjing) Co., Ltd.
+arctic	Arctic Sand
+aries	Aries Embedded GmbH
+arm	ARM Ltd.
+armadeus	ARMadeus Systems SARL
+arrow	Arrow Electronics
+artesyn	Artesyn Embedded Technologies Inc.
+asahi-kasei	Asahi Kasei Corp.
+aspeed	ASPEED Technology Inc.
+asus	AsusTek Computer Inc.
+atlas	Atlas Scientific LLC
+atmel	Atmel Corporation
+auo	AU Optronics Corporation
+auvidea Auvidea GmbH
+avago	Avago Technologies
+avia	avia semiconductor
+avic	Shanghai AVIC Optoelectronics Co., Ltd.
+avnet	Avnet, Inc.
+axentia	Axentia Technologies AB
+axis	Axis Communications AB
+bananapi BIPAI KEJI LIMITED
+bhf	Beckhoff Automation GmbH & Co. KG
+bitmain	Bitmain Technologies
+blokaslabs	Vilniaus Blokas UAB
+boe	BOE Technology Group Co., Ltd.
+bosch	Bosch Sensortec GmbH
+boundary	Boundary Devices Inc.
+brcm	Broadcom Corporation
+buffalo	Buffalo, Inc.
+bticino Bticino International
+calxeda	Calxeda
+capella	Capella Microsystems, Inc
+cascoda	Cascoda, Ltd.
+catalyst	Catalyst Semiconductor, Inc.
+cavium	Cavium, Inc.
+cdns	Cadence Design Systems Inc.
+cdtech	CDTech(H.K.) Electronics Limited
+ceva	Ceva, Inc.
+chipidea	Chipidea, Inc
+chipone		ChipOne
+chipspark	ChipSPARK
+chrp	Common Hardware Reference Platform
+chunghwa	Chunghwa Picture Tubes Ltd.
+ciaa	Computadora Industrial Abierta Argentina
+cirrus	Cirrus Logic, Inc.
+cloudengines	Cloud Engines, Inc.
+cnm	Chips&Media, Inc.
+cnxt	Conexant Systems, Inc.
+compulab	CompuLab Ltd.
+cortina	Cortina Systems, Inc.
+cosmic	Cosmic Circuits
+crane	Crane Connectivity Solutions
+creative	Creative Technology Ltd
+crystalfontz	Crystalfontz America, Inc.
+csky	Hangzhou C-SKY Microsystems Co., Ltd
+cubietech	Cubietech, Ltd.
+cypress	Cypress Semiconductor Corporation
+cznic	CZ.NIC, z.s.p.o.
+dallas	Maxim Integrated Products (formerly Dallas Semiconductor)
+dataimage	DataImage, Inc.
+davicom	DAVICOM Semiconductor, Inc.
+delta	Delta Electronics, Inc.
+denx	Denx Software Engineering
+devantech	Devantech, Ltd.
+dh	DH electronics GmbH
+digi	Digi International Inc.
+digilent	Diglent, Inc.
+dioo	Dioo Microcircuit Co., Ltd
+dlc	DLC Display Co., Ltd.
+dlg	Dialog Semiconductor
+dlink	D-Link Corporation
+dmo	Data Modul AG
+domintech	Domintech Co., Ltd.
+dongwoon	Dongwoon Anatech
+dptechnics	DPTechnics
+dragino	Dragino Technology Co., Limited
+ea	Embedded Artists AB
+ebs-systart EBS-SYSTART GmbH
+ebv	EBV Elektronik
+eckelmann	Eckelmann AG
+edt	Emerging Display Technologies
+eeti	eGalax_eMPIA Technology Inc
+elan	Elan Microelectronic Corp.
+elgin	Elgin S/A.
+embest	Shenzhen Embest Technology Co., Ltd.
+emlid	Emlid, Ltd.
+emmicro	EM Microelectronic
+emtrion	emtrion GmbH
+endless	Endless Mobile, Inc.
+energymicro	Silicon Laboratories (formerly Energy Micro AS)
+engicam	Engicam S.r.l.
+epcos	EPCOS AG
+epfl	Ecole Polytechnique Fédérale de Lausanne
+epson	Seiko Epson Corp.
+est	ESTeem Wireless Modems
+ettus	NI Ettus Research
+eukrea  Eukréa Electromatique
+everest	Everest Semiconductor Co. Ltd.
+everspin	Everspin Technologies, Inc.
+exar	Exar Corporation
+excito	Excito
+ezchip	EZchip Semiconductor
+facebook	Facebook
+fairphone	Fairphone B.V.
+faraday	Faraday Technology Corporation
+fastrax	Fastrax Oy
+fcs	Fairchild Semiconductor
+feiyang	Shenzhen Fly Young Technology Co.,LTD.
+firefly	Firefly
+focaltech	FocalTech Systems Co.,Ltd
+friendlyarm	Guangzhou FriendlyARM Computer Tech Co., Ltd
+fsl	Freescale Semiconductor
+fujitsu	Fujitsu Ltd.
+gateworks	Gateworks Corporation
+gcw Game Consoles Worldwide
+ge	General Electric Company
+geekbuying	GeekBuying
+gef	GE Fanuc Intelligent Platforms Embedded Systems, Inc.
+GEFanuc	GE Fanuc Intelligent Platforms Embedded Systems, Inc.
+geniatech	Geniatech, Inc.
+giantec	Giantec Semiconductor, Inc.
+giantplus	Giantplus Technology Co., Ltd.
+globalscale	Globalscale Technologies, Inc.
+globaltop	GlobalTop Technology, Inc.
+gmt	Global Mixed-mode Technology, Inc.
+goodix	Shenzhen Huiding Technology Co., Ltd.
+google	Google, Inc.
+grinn	Grinn
+grmn	Garmin Limited
+gumstix	Gumstix, Inc.
+gw	Gateworks Corporation
+hannstar	HannStar Display Corporation
+haoyu	Haoyu Microelectronic Co. Ltd.
+hardkernel	Hardkernel Co., Ltd
+hideep	HiDeep Inc.
+himax	Himax Technologies, Inc.
+hisilicon	Hisilicon Limited.
+hit	Hitachi Ltd.
+hitex	Hitex Development Tools
+holt	Holt Integrated Circuits, Inc.
+honeywell	Honeywell
+hp	Hewlett Packard
+holtek	Holtek Semiconductor, Inc.
+hwacom	HwaCom Systems Inc.
+i2se	I2SE GmbH
+ibm	International Business Machines (IBM)
+icplus	IC Plus Corp.
+idt	Integrated Device Technologies, Inc.
+ifi	Ingenieurburo Fur Ic-Technologie (I/F/I)
+ilitek	ILI Technology Corporation (ILITEK)
+img	Imagination Technologies Ltd.
+infineon Infineon Technologies
+inforce	Inforce Computing
+ingenic	Ingenic Semiconductor
+innolux	Innolux Corporation
+inside-secure	INSIDE Secure
+intel	Intel Corporation
+intercontrol	Inter Control Group
+invensense	InvenSense Inc.
+inversepath	Inverse Path
+iom	Iomega Corporation
+isee	ISEE 2007 S.L.
+isil	Intersil
+issi	Integrated Silicon Solutions Inc.
+itead	ITEAD Intelligent Systems Co.Ltd
+iwave  iWave Systems Technologies Pvt. Ltd.
+jdi	Japan Display Inc.
+jedec	JEDEC Solid State Technology Association
+jianda	Jiandangjing Technology Co., Ltd.
+karo	Ka-Ro electronics GmbH
+keithkoep	Keith & Koep GmbH
+keymile	Keymile GmbH
+khadas	Khadas
+kiebackpeter    Kieback & Peter GmbH
+kinetic Kinetic Technologies
+kingdisplay	King & Display Technology Co., Ltd.
+kingnovel	Kingnovel Technology Co., Ltd.
+koe	Kaohsiung Opto-Electronics Inc.
+kosagi	Sutajio Ko-Usagi PTE Ltd.
+kyo	Kyocera Corporation
+lacie	LaCie
+laird	Laird PLC
+lantiq	Lantiq Semiconductor
+lattice	Lattice Semiconductor
+lego	LEGO Systems A/S
+lemaker	Shenzhen LeMaker Technology Co., Ltd.
+lenovo	Lenovo Group Ltd.
+lg	LG Corporation
+libretech	Shenzhen Libre Technology Co., Ltd
+licheepi	Lichee Pi
+linaro	Linaro Limited
+linksys	Belkin International, Inc. (Linksys)
+linux	Linux-specific binding
+linx	Linx Technologies
+lltc	Linear Technology Corporation
+logicpd	Logic PD, Inc.
+lsi	LSI Corp. (LSI Logic)
+lwn	Liebherr-Werk Nenzing GmbH
+macnica	Macnica Americas
+marvell	Marvell Technology Group Ltd.
+maxim	Maxim Integrated Products
+mbvl	Mobiveil Inc.
+mcube	mCube
+meas	Measurement Specialties
+mediatek	MediaTek Inc.
+megachips	MegaChips
+mele	Shenzhen MeLE Digital Technology Ltd.
+melexis	Melexis N.V.
+melfas	MELFAS Inc.
+mellanox	Mellanox Technologies
+memsic	MEMSIC Inc.
+merrii	Merrii Technology Co., Ltd.
+micrel	Micrel Inc.
+microchip	Microchip Technology Inc.
+microcrystal	Micro Crystal AG
+micron	Micron Technology Inc.
+mikroe		MikroElektronika d.o.o.
+minix	MINIX Technology Ltd.
+miramems	MiraMEMS Sensing Technology Co., Ltd.
+mitsubishi	Mitsubishi Electric Corporation
+mosaixtech	Mosaix Technologies, Inc.
+motorola	Motorola, Inc.
+moxa	Moxa Inc.
+mpl	MPL AG
+mqmaker	mqmaker Inc.
+mscc	Microsemi Corporation
+msi	Micro-Star International Co. Ltd.
+mti	Imagination Technologies Ltd. (formerly MIPS Technologies Inc.)
+multi-inno	Multi-Inno Technology Co.,Ltd
+mundoreader	Mundo Reader S.L.
+murata	Murata Manufacturing Co., Ltd.
+mxicy	Macronix International Co., Ltd.
+myir	MYIR Tech Limited
+national	National Semiconductor
+nec	NEC LCD Technologies, Ltd.
+neonode		Neonode Inc.
+netgear	NETGEAR
+netlogic	Broadcom Corporation (formerly NetLogic Microsystems)
+netron-dy	Netron DY
+netxeon		Shenzhen Netxeon Technology CO., LTD
+nexbox	Nexbox
+nextthing	Next Thing Co.
+newhaven	Newhaven Display International
+ni	National Instruments
+nintendo	Nintendo
+nlt	NLT Technologies, Ltd.
+nokia	Nokia
+nordic	Nordic Semiconductor
+novtech NovTech, Inc.
+nutsboard	NutsBoard
+nuvoton	Nuvoton Technology Corporation
+nvd	New Vision Display
+nvidia	NVIDIA
+nxp	NXP Semiconductors
+okaya	Okaya Electric America, Inc.
+oki	Oki Electric Industry Co., Ltd.
+olimex	OLIMEX Ltd.
+olpc	One Laptop Per Child
+onion	Onion Corporation
+onnn	ON Semiconductor Corp.
+ontat	On Tat Industrial Company
+opalkelly	Opal Kelly Incorporated
+opencores	OpenCores.org
+openrisc	OpenRISC.io
+option	Option NV
+oranth	Shenzhen Oranth Technology Co., Ltd.
+ORCL	Oracle Corporation
+orisetech	Orise Technology
+ortustech	Ortus Technology Co., Ltd.
+ovti	OmniVision Technologies
+oxsemi	Oxford Semiconductor, Ltd.
+panasonic	Panasonic Corporation
+parade	Parade Technologies Inc.
+pda	Precision Design Associates, Inc.
+pericom	Pericom Technology Inc.
+pervasive	Pervasive Displays, Inc.
+phicomm PHICOMM Co., Ltd.
+phytec	PHYTEC Messtechnik GmbH
+picochip	Picochip Ltd
+pine64	Pine64
+pixcir  PIXCIR MICROELECTRONICS Co., Ltd
+plantower Plantower Co., Ltd
+plathome	Plat'Home Co., Ltd.
+plda	PLDA
+plx	Broadcom Corporation (formerly PLX Technology)
+pni	PNI Sensor Corporation
+portwell	Portwell Inc.
+poslab	Poslab Technology Co., Ltd.
+powervr	PowerVR (deprecated, use img)
+probox2	PROBOX2 (by W2COMP Co., Ltd.)
+pulsedlight	PulsedLight, Inc
+qca	Qualcomm Atheros, Inc.
+qcom	Qualcomm Technologies, Inc
+qemu	QEMU, a generic and open source machine emulator and virtualizer
+qi	Qi Hardware
+qiaodian	QiaoDian XianShi Corporation
+qnap	QNAP Systems, Inc.
+radxa	Radxa
+raidsonic	RaidSonic Technology GmbH
+ralink	Mediatek/Ralink Technology Corp.
+ramtron	Ramtron International
+raspberrypi	Raspberry Pi Foundation
+raydium	Raydium Semiconductor Corp.
+rda	Unisoc Communications, Inc.
+realtek Realtek Semiconductor Corp.
+renesas	Renesas Electronics Corporation
+richtek	Richtek Technology Corporation
+ricoh	Ricoh Co. Ltd.
+rikomagic	Rikomagic Tech Corp. Ltd
+riscv	RISC-V Foundation
+rockchip	Fuzhou Rockchip Electronics Co., Ltd
+rohm	ROHM Semiconductor Co., Ltd
+roofull	Shenzhen Roofull Technology Co, Ltd
+samsung	Samsung Semiconductor
+samtec	Samtec/Softing company
+sancloud	Sancloud Ltd
+sandisk	Sandisk Corporation
+sbs	Smart Battery System
+schindler	Schindler
+seagate	Seagate Technology PLC
+semtech	Semtech Corporation
+sensirion	Sensirion AG
+sff	Small Form Factor Committee
+sgd	Solomon Goldentek Display Corporation
+sgx	SGX Sensortech
+sharp	Sharp Corporation
+shimafuji	Shimafuji Electric, Inc.
+si-en	Si-En Technology Ltd.
+sifive	SiFive, Inc.
+sigma	Sigma Designs, Inc.
+sii	Seiko Instruments, Inc.
+sil	Silicon Image
+silabs	Silicon Laboratories
+silead	Silead Inc.
+silergy	Silergy Corp.
+siliconmitus	Silicon Mitus, Inc.
+simtek
+sirf	SiRF Technology, Inc.
+sis	Silicon Integrated Systems Corp.
+sitronix	Sitronix Technology Corporation
+skyworks	Skyworks Solutions, Inc.
+smsc	Standard Microsystems Corporation
+snps	Synopsys, Inc.
+socionext	Socionext Inc.
+solidrun	SolidRun
+solomon        Solomon Systech Limited
+sony	Sony Corporation
+spansion	Spansion Inc.
+sprd	Spreadtrum Communications Inc.
+sst	Silicon Storage Technology, Inc.
+st	STMicroelectronics
+starry	Starry Electronic Technology (ShenZhen) Co., LTD
+startek	Startek
+ste	ST-Ericsson
+stericsson	ST-Ericsson
+summit	Summit microelectronics
+sunchip	Shenzhen Sunchip Technology Co., Ltd
+SUNW	Sun Microsystems, Inc
+swir	Sierra Wireless
+syna	Synaptics Inc.
+synology	Synology, Inc.
+tbs	TBS Technologies
+tbs-biometrics	Touchless Biometric Systems AG
+tcg	Trusted Computing Group
+tcl	Toby Churchill Ltd.
+technexion	TechNexion
+technologic	Technologic Systems
+tempo	Tempo Semiconductor
+techstar	Shenzhen Techstar Electronics Co., Ltd.
+terasic	Terasic Inc.
+thine	THine Electronics, Inc.
+ti	Texas Instruments
+tianma	Tianma Micro-electronics Co., Ltd.
+tlm	Trusted Logic Mobility
+tmt	Tecon Microprocessor Technologies, LLC.
+topeet  Topeet
+toradex	Toradex AG
+toshiba	Toshiba Corporation
+toumaz	Toumaz
+tpk	TPK U.S.A. LLC
+tplink	TP-LINK Technologies Co., Ltd.
+tpo	TPO
+tronfy	Tronfy
+tronsmart	Tronsmart
+truly	Truly Semiconductors Limited
+tsd	Theobroma Systems Design und Consulting GmbH
+tyan	Tyan Computer Corporation
+u-blox	u-blox
+ucrobotics	uCRobotics
+ubnt	Ubiquiti Networks
+udoo	Udoo
+uniwest	United Western Technologies Corp (UniWest)
+upisemi	uPI Semiconductor Corp.
+urt	United Radiant Technology Corporation
+usi	Universal Scientific Industrial Co., Ltd.
+v3	V3 Semiconductor
+vamrs	Vamrs Ltd.
+variscite	Variscite Ltd.
+via	VIA Technologies, Inc.
+virtio	Virtual I/O Device Specification, developed by the OASIS consortium
+vishay	Vishay Intertechnology, Inc
+vitesse	Vitesse Semiconductor Corporation
+vivante	Vivante Corporation
+vocore VoCore Studio
+voipac	Voipac Technologies s.r.o.
+vot	Vision Optical Technology Co., Ltd.
+wd	Western Digital Corp.
+wetek	WeTek Electronics, limited.
+wexler	Wexler
+whwave  Shenzhen whwave Electronics, Inc.
+wi2wi	Wi2Wi, Inc.
+winbond Winbond Electronics corp.
+winstar	Winstar Display Corp.
+wlf	Wolfson Microelectronics
+wm	Wondermedia Technologies, Inc.
+x-powers	X-Powers
+xes	Extreme Engineering Solutions (X-ES)
+xillybus	Xillybus Ltd.
+xlnx	Xilinx
+xunlong	Shenzhen Xunlong Software CO.,Limited
+ysoft	Y Soft Corporation a.s.
+zarlink	Zarlink Semiconductor
+zeitec	ZEITEC Semiconductor Co., LTD.
+zidoo	Shenzhen Zidoo Technology Co., Ltd.
+zii	Zodiac Inflight Innovations
+zte	ZTE Corp.
+zyxel	ZyXEL Communications Corp.

Documentation/devicetree/bindings/vendor-prefixes.yaml

@@ -139,6 +139,8 @@ patternProperties:
     description: Beckhoff Automation GmbH & Co. KG
   "^bitmain,.*":
     description: Bitmain Technologies
+  "^blokaslabs,.*":
+    description: Vilniaus Blokas UAB
   "^boe,.*":
     description: BOE Technology Group Co., Ltd.
   "^bosch,.*":

Documentation/devicetree/configfs-overlays.txt

@@ -0,0 +1,31 @@
+Howto use the configfs overlay interface.
+
+A device-tree configfs entry is created in /config/device-tree/overlays
+and and it is manipulated using standard file system I/O.
+Note that this is a debug level interface, for use by developers and
+not necessarily something accessed by normal users due to the
+security implications of having direct access to the kernel's device tree.
+
+* To create an overlay you mkdir the directory:
+
+	# mkdir /config/device-tree/overlays/foo
+
+* Either you echo the overlay firmware file to the path property file.
+
+	# echo foo.dtbo >/config/device-tree/overlays/foo/path
+
+* Or you cat the contents of the overlay to the dtbo file
+
+	# cat foo.dtbo >/config/device-tree/overlays/foo/dtbo
+
+The overlay file will be applied, and devices will be created/destroyed
+as required.
+
+To remove it simply rmdir the directory.
+
+	# rmdir /config/device-tree/overlays/foo
+
+The rationalle of the dual interface (firmware & direct copy) is that each is
+better suited to different use patterns. The firmware interface is what's
+intended to be used by hardware managers in the kernel, while the copy interface
+make sense for developers (since it avoids problems with namespaces).

Documentation/filesystems/overlayfs.txt

@@ -302,7 +302,7 @@ beneath or above the path of another overlay lower layer path.
 
 Using an upper layer path and/or a workdir path that are already used by
 another overlay mount is not allowed and may fail with EBUSY.  Using
-partially overlapping paths is not allowed but will not fail with EBUSY.
+partially overlapping paths is not allowed and may fail with EBUSY.
 If files are accessed from two overlayfs mounts which share or overlap the
 upper layer and/or workdir path the behavior of the overlay is undefined,
 though it will not result in a crash or deadlock.

Documentation/hwmon/rpi-poe-fan

@@ -0,0 +1,15 @@
+Kernel driver rpi-poe-fan
+=====================
+
+This driver enables the use of the Raspberry Pi PoE HAT fan.
+
+Author: Serge Schneider <serge@raspberrypi.org>
+
+Description
+-----------
+
+The driver implements a simple interface for driving the Raspberry Pi PoE
+(Power over Ethernet) HAT fan. The driver passes commands to the Raspberry Pi
+firmware through the mailbox property interface. The firmware then forwards
+the commands to the board over I2C on the ID_EEPROM pins. The driver exposes
+the fan to the user space through the hwmon sysfs interface.

Documentation/scheduler/sched-bwc.rst

@@ -9,15 +9,16 @@ CFS bandwidth control is a CONFIG_FAIR_GROUP_SCHED extension which allows the
 specification of the maximum CPU bandwidth available to a group or hierarchy.
 
 The bandwidth allowed for a group is specified using a quota and period. Within
-each given "period" (microseconds), a group is allowed to consume only up to
+each given "period" (microseconds), a task group is allocated up to "quota"
-"quota" microseconds of CPU time.  When the CPU bandwidth consumption of a
+microseconds of CPU time. That quota is assigned to per-cpu run queues in
-group exceeds this limit (for that period), the tasks belonging to its
+slices as threads in the cgroup become runnable. Once all quota has been
-hierarchy will be throttled and are not allowed to run again until the next
+assigned any additional requests for quota will result in those threads being
-period.
+throttled. Throttled threads will not be able to run again until the next
+period when the quota is replenished.
 
-A group's unused runtime is globally tracked, being refreshed with quota units
+A group's unassigned quota is globally tracked, being refreshed back to
-above at each period boundary.  As threads consume this bandwidth it is
+cfs_quota units at each period boundary. As threads consume this bandwidth it
-transferred to cpu-local "silos" on a demand basis.  The amount transferred
+is transferred to cpu-local "silos" on a demand basis. The amount transferred
 within each of these updates is tunable and described as the "slice".
 
 Management
@@ -97,6 +98,51 @@ There are two ways in which a group may become throttled:
 In case b) above, even though the child may have runtime remaining it will not
 be allowed to until the parent's runtime is refreshed.
 
+CFS Bandwidth Quota Caveats
+---------------------------
+Once a slice is assigned to a cpu it does not expire.  However all but 1ms of
+the slice may be returned to the global pool if all threads on that cpu become
+unrunnable. This is configured at compile time by the min_cfs_rq_runtime
+variable. This is a performance tweak that helps prevent added contention on
+the global lock.
+
+The fact that cpu-local slices do not expire results in some interesting corner
+cases that should be understood.
+
+For cgroup cpu constrained applications that are cpu limited this is a
+relatively moot point because they will naturally consume the entirety of their
+quota as well as the entirety of each cpu-local slice in each period. As a
+result it is expected that nr_periods roughly equal nr_throttled, and that
+cpuacct.usage will increase roughly equal to cfs_quota_us in each period.
+
+For highly-threaded, non-cpu bound applications this non-expiration nuance
+allows applications to briefly burst past their quota limits by the amount of
+unused slice on each cpu that the task group is running on (typically at most
+1ms per cpu or as defined by min_cfs_rq_runtime).  This slight burst only
+applies if quota had been assigned to a cpu and then not fully used or returned
+in previous periods. This burst amount will not be transferred between cores.
+As a result, this mechanism still strictly limits the task group to quota
+average usage, albeit over a longer time window than a single period.  This
+also limits the burst ability to no more than 1ms per cpu.  This provides
+better more predictable user experience for highly threaded applications with
+small quota limits on high core count machines. It also eliminates the
+propensity to throttle these applications while simultanously using less than
+quota amounts of cpu. Another way to say this, is that by allowing the unused
+portion of a slice to remain valid across periods we have decreased the
+possibility of wastefully expiring quota on cpu-local silos that don't need a
+full slice's amount of cpu time.
+
+The interaction between cpu-bound and non-cpu-bound-interactive applications
+should also be considered, especially when single core usage hits 100%. If you
+gave each of these applications half of a cpu-core and they both got scheduled
+on the same CPU it is theoretically possible that the non-cpu bound application
+will use up to 1ms additional quota in some periods, thereby preventing the
+cpu-bound application from fully using its quota by that same amount. In these
+instances it will be up to the CFS algorithm (see sched-design-CFS.rst) to
+decide which application is chosen to run, as they will both be runnable and
+have remaining quota. This runtime discrepancy will be made up in the following
+periods when the interactive application idles.
+
 Examples
 --------
 1. Limit a group to 1 CPU worth of runtime::

Documentation/sound/hd-audio/models.rst

@@ -260,6 +260,9 @@ alc295-hp-x360
     HP Spectre X360 fixups
 alc-sense-combo
     Headset button support for Chrome platform
+huawei-mbx-stereo
+    Enable initialization verbs for Huawei MBX stereo speakers;
+    might be risky, try this at your own risk
 
 ALC66x/67x/892
 ==============

Documentation/sphinx/automarkup.py

@@ -25,7 +25,7 @@ RE_function = re.compile(r'([\w_][\w\d_]+\(\))')
 # to the creation of incorrect and confusing cross references.  So
 # just don't even try with these names.
 #
-Skipfuncs = [ 'open', 'close', 'read', 'write', 'fcntl', 'mmap'
+Skipfuncs = [ 'open', 'close', 'read', 'write', 'fcntl', 'mmap',
               'select', 'poll', 'fork', 'execve', 'clone', 'ioctl']
 
 #

Documentation/usb/rio.rst

@@ -1,109 +0,0 @@
-============
-Diamonds Rio
-============
-
-Copyright (C) 1999, 2000 Bruce Tenison
-
-Portions Copyright (C) 1999, 2000 David Nelson
-
-Thanks to David Nelson for guidance and the usage of the scanner.txt
-and scanner.c files to model our driver and this informative file.
-
-Mar. 2, 2000
-
-Changes
-=======
-
-- Initial Revision
-
-
-Overview
-========
-
-This README will address issues regarding how to configure the kernel
-to access a RIO 500 mp3 player.
-Before I explain how to use this to access the Rio500 please be warned:
-
-.. warning::
-
-   Please note that this software is still under development.  The authors
-   are in no way responsible for any damage that may occur, no matter how
-   inconsequential.
-
-It seems that the Rio has a problem when sending .mp3 with low batteries.
-I suggest when the batteries are low and you want to transfer stuff that you
-replace it with a fresh one. In my case, what happened is I lost two 16kb
-blocks (they are no longer usable to store information to it). But I don't
-know if that's normal or not; it could simply be a problem with the flash
-memory.
-
-In an extreme case, I left my Rio playing overnight and the batteries wore
-down to nothing and appear to have corrupted the flash memory. My RIO
-needed to be replaced as a result.  Diamond tech support is aware of the
-problem.  Do NOT allow your batteries to wear down to nothing before
-changing them.  It appears RIO 500 firmware does not handle low battery
-power well at all.
-
-On systems with OHCI controllers, the kernel OHCI code appears to have
-power on problems with some chipsets.  If you are having problems
-connecting to your RIO 500, try turning it on first and then plugging it
-into the USB cable.
-
-Contact Information
--------------------
-
-   The main page for the project is hosted at sourceforge.net in the following
-   URL: <http://rio500.sourceforge.net>. You can also go to the project's
-   sourceforge home page at: <http://sourceforge.net/projects/rio500/>.
-   There is also a mailing list: rio500-users@lists.sourceforge.net
-
-Authors
--------
-
-Most of the code was written by Cesar Miquel <miquel@df.uba.ar>. Keith
-Clayton <kclayton@jps.net> is incharge of the PPC port and making sure
-things work there. Bruce Tenison <btenison@dibbs.net> is adding support
-for .fon files and also does testing. The program will mostly sure be
-re-written and Pete Ikusz along with the rest will re-design it. I would
-also like to thank Tri Nguyen <tmn_3022000@hotmail.com> who provided use
-with some important information regarding the communication with the Rio.
-
-Additional Information and userspace tools
-
-	http://rio500.sourceforge.net/
-
-
-Requirements
-============
-
-A host with a USB port running a Linux kernel with RIO 500 support enabled.
-
-The driver is a module called rio500, which should be automatically loaded
-as you plug in your device. If that fails you can manually load it with
-
-  modprobe rio500
-
-Udev should automatically create a device node as soon as plug in your device.
-If that fails, you can manually add a device for the USB rio500::
-
-  mknod /dev/usb/rio500 c 180 64
-
-In that case, set appropriate permissions for /dev/usb/rio500 (don't forget
-about group and world permissions).  Both read and write permissions are
-required for proper operation.
-
-That's it.  The Rio500 Utils at: http://rio500.sourceforge.net should
-be able to access the rio500.
-
-Limits
-======
-
-You can use only a single rio500 device at a time with your computer.
-
-Bugs
-====
-
-If you encounter any problems feel free to drop me an email.
-
-Bruce Tenison
-btenison@dibbs.net

Documentation/x86/index.rst

@@ -27,6 +27,7 @@ x86-specific Documentation
    mds
    microcode
    resctrl_ui
+   tsx_async_abort
    usb-legacy-support
    i386/index
    x86_64/index

Documentation/x86/tsx_async_abort.rst

@@ -0,0 +1,117 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+TSX Async Abort (TAA) mitigation
+================================
+
+.. _tsx_async_abort:
+
+Overview
+--------
+
+TSX Async Abort (TAA) is a side channel attack on internal buffers in some
+Intel processors similar to Microachitectural Data Sampling (MDS).  In this
+case certain loads may speculatively pass invalid data to dependent operations
+when an asynchronous abort condition is pending in a Transactional
+Synchronization Extensions (TSX) transaction.  This includes loads with no
+fault or assist condition. Such loads may speculatively expose stale data from
+the same uarch data structures as in MDS, with same scope of exposure i.e.
+same-thread and cross-thread. This issue affects all current processors that
+support TSX.
+
+Mitigation strategy
+-------------------
+
+a) TSX disable - one of the mitigations is to disable TSX. A new MSR
+IA32_TSX_CTRL will be available in future and current processors after
+microcode update which can be used to disable TSX. In addition, it
+controls the enumeration of the TSX feature bits (RTM and HLE) in CPUID.
+
+b) Clear CPU buffers - similar to MDS, clearing the CPU buffers mitigates this
+vulnerability. More details on this approach can be found in
+:ref:`Documentation/admin-guide/hw-vuln/mds.rst <mds>`.
+
+Kernel internal mitigation modes
+--------------------------------
+
+ =============    ============================================================
+ off              Mitigation is disabled. Either the CPU is not affected or
+                  tsx_async_abort=off is supplied on the kernel command line.
+
+ tsx disabled     Mitigation is enabled. TSX feature is disabled by default at
+                  bootup on processors that support TSX control.
+
+ verw             Mitigation is enabled. CPU is affected and MD_CLEAR is
+                  advertised in CPUID.
+
+ ucode needed     Mitigation is enabled. CPU is affected and MD_CLEAR is not
+                  advertised in CPUID. That is mainly for virtualization
+                  scenarios where the host has the updated microcode but the
+                  hypervisor does not expose MD_CLEAR in CPUID. It's a best
+                  effort approach without guarantee.
+ =============    ============================================================
+
+If the CPU is affected and the "tsx_async_abort" kernel command line parameter is
+not provided then the kernel selects an appropriate mitigation depending on the
+status of RTM and MD_CLEAR CPUID bits.
+
+Below tables indicate the impact of tsx=on|off|auto cmdline options on state of
+TAA mitigation, VERW behavior and TSX feature for various combinations of
+MSR_IA32_ARCH_CAPABILITIES bits.
+
+1. "tsx=off"
+
+=========  =========  ============  ============  ==============  ===================  ======================
+MSR_IA32_ARCH_CAPABILITIES bits     Result with cmdline tsx=off
+----------------------------------  -------------------------------------------------------------------------
+TAA_NO     MDS_NO     TSX_CTRL_MSR  TSX state     VERW can clear  TAA mitigation       TAA mitigation
+                                    after bootup  CPU buffers     tsx_async_abort=off  tsx_async_abort=full
+=========  =========  ============  ============  ==============  ===================  ======================
+    0          0           0         HW default         Yes           Same as MDS           Same as MDS
+    0          0           1        Invalid case   Invalid case       Invalid case          Invalid case
+    0          1           0         HW default         No         Need ucode update     Need ucode update
+    0          1           1          Disabled          Yes           TSX disabled          TSX disabled
+    1          X           1          Disabled           X             None needed           None needed
+=========  =========  ============  ============  ==============  ===================  ======================
+
+2. "tsx=on"
+
+=========  =========  ============  ============  ==============  ===================  ======================
+MSR_IA32_ARCH_CAPABILITIES bits     Result with cmdline tsx=on
+----------------------------------  -------------------------------------------------------------------------
+TAA_NO     MDS_NO     TSX_CTRL_MSR  TSX state     VERW can clear  TAA mitigation       TAA mitigation
+                                    after bootup  CPU buffers     tsx_async_abort=off  tsx_async_abort=full
+=========  =========  ============  ============  ==============  ===================  ======================
+    0          0           0         HW default        Yes            Same as MDS          Same as MDS
+    0          0           1        Invalid case   Invalid case       Invalid case         Invalid case
+    0          1           0         HW default        No          Need ucode update     Need ucode update
+    0          1           1          Enabled          Yes               None              Same as MDS
+    1          X           1          Enabled          X              None needed          None needed
+=========  =========  ============  ============  ==============  ===================  ======================
+
+3. "tsx=auto"
+
+=========  =========  ============  ============  ==============  ===================  ======================
+MSR_IA32_ARCH_CAPABILITIES bits     Result with cmdline tsx=auto
+----------------------------------  -------------------------------------------------------------------------
+TAA_NO     MDS_NO     TSX_CTRL_MSR  TSX state     VERW can clear  TAA mitigation       TAA mitigation
+                                    after bootup  CPU buffers     tsx_async_abort=off  tsx_async_abort=full
+=========  =========  ============  ============  ==============  ===================  ======================
+    0          0           0         HW default    Yes                Same as MDS           Same as MDS
+    0          0           1        Invalid case  Invalid case        Invalid case          Invalid case
+    0          1           0         HW default    No              Need ucode update     Need ucode update
+    0          1           1          Disabled      Yes               TSX disabled          TSX disabled
+    1          X           1          Enabled       X                 None needed           None needed
+=========  =========  ============  ============  ==============  ===================  ======================
+
+In the tables, TSX_CTRL_MSR is a new bit in MSR_IA32_ARCH_CAPABILITIES that
+indicates whether MSR_IA32_TSX_CTRL is supported.
+
+There are two control bits in IA32_TSX_CTRL MSR:
+
+      Bit 0: When set it disables the Restricted Transactional Memory (RTM)
+             sub-feature of TSX (will force all transactions to abort on the
+             XBEGIN instruction).
+
+      Bit 1: When set it disables the enumeration of the RTM and HLE feature
+             (i.e. it will make CPUID(EAX=7).EBX{bit4} and
+             CPUID(EAX=7).EBX{bit11} read as 0).

MAINTAINERS

@@ -3183,6 +3183,13 @@ S:	Maintained
 N:	bcm2835
 F:	drivers/staging/vc04_services
 
+BROADCOM BCM2835 CAMERA DRIVER
+M:	Dave Stevenson <dave.stevenson@raspberrypi.org>
+L:	linux-media@vger.kernel.org
+S:	Maintained
+F:	drivers/media/platform/bcm2835/
+F:	Documentation/devicetree/bindings/media/bcm2835-unicam.txt
+
 BROADCOM BCM47XX MIPS ARCHITECTURE
 M:	Hauke Mehrtens <hauke@hauke-m.de>
 M:	Rafał Miłecki <zajec5@gmail.com>
@@ -16606,13 +16613,6 @@ W:	http://www.linux-usb.org/usbnet
 S:	Maintained
 F:	drivers/net/usb/dm9601.c
 
-USB DIAMOND RIO500 DRIVER
-M:	Cesar Miquel <miquel@df.uba.ar>
-L:	rio500-users@lists.sourceforge.net
-W:	http://rio500.sourceforge.net
-S:	Maintained
-F:	drivers/usb/misc/rio500*
-
 USB EHCI DRIVER
 M:	Alan Stern <stern@rowland.harvard.edu>
 L:	linux-usb@vger.kernel.org

Makefile

@@ -1,7 +1,7 @@
 # SPDX-License-Identifier: GPL-2.0
 VERSION = 5
 PATCHLEVEL = 3
-SUBLEVEL = 0
+SUBLEVEL = 18
 EXTRAVERSION =
 NAME = Bobtail Squid
 
@@ -751,6 +751,11 @@ else
 # These warnings generated too much noise in a regular build.
 # Use make W=1 to enable them (see scripts/Makefile.extrawarn)
 KBUILD_CFLAGS += -Wno-unused-but-set-variable
+
+# Warn about unmarked fall-throughs in switch statement.
+# Disabled for clang while comment to attribute conversion happens and
+# https://github.com/ClangBuiltLinux/linux/issues/636 is discussed.
+KBUILD_CFLAGS += $(call cc-option,-Wimplicit-fallthrough,)
 endif
 
 KBUILD_CFLAGS += $(call cc-disable-warning, unused-const-variable)
@@ -845,9 +850,6 @@ NOSTDINC_FLAGS += -nostdinc -isystem $(shell $(CC) -print-file-name=include)
 # warn about C99 declaration after statement
 KBUILD_CFLAGS += -Wdeclaration-after-statement
 
-# Warn about unmarked fall-throughs in switch statement.
-KBUILD_CFLAGS += $(call cc-option,-Wimplicit-fallthrough,)
-
 # Variable Length Arrays (VLAs) should not be used anywhere in the kernel
 KBUILD_CFLAGS += -Wvla
 
@@ -1258,6 +1260,9 @@ ifneq ($(dtstree),)
 %.dtb: prepare3 scripts_dtc
 	$(Q)$(MAKE) $(build)=$(dtstree) $(dtstree)/$@
 
+%.dtbo: prepare3 scripts_dtc
+	$(Q)$(MAKE) $(build)=$(dtstree) $(dtstree)/$@
+
 PHONY += dtbs dtbs_install dt_binding_check
 dtbs dtbs_check: prepare3 scripts_dtc
 	$(Q)$(MAKE) $(build)=$(dtstree)

arch/arc/boot/dts/hsdk.dts

@@ -264,6 +264,14 @@
 			clocks = <&input_clk>;
 			cs-gpios = <&creg_gpio 0 GPIO_ACTIVE_LOW>,
 				   <&creg_gpio 1 GPIO_ACTIVE_LOW>;
+
+			spi-flash@0 {
+				compatible = "sst26wf016b", "jedec,spi-nor";
+				reg = <0>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				spi-max-frequency = <4000000>;
+			};
 		};
 
 		creg_gpio: gpio@14b0 {

arch/arc/configs/hsdk_defconfig

@@ -31,6 +31,8 @@ CONFIG_INET=y
 CONFIG_DEVTMPFS=y
 # CONFIG_STANDALONE is not set
 # CONFIG_PREVENT_FIRMWARE_BUILD is not set
+CONFIG_MTD=y
+CONFIG_MTD_SPI_NOR=y
 CONFIG_SCSI=y
 CONFIG_BLK_DEV_SD=y
 CONFIG_NETDEVICES=y

arch/arc/kernel/perf_event.c

@@ -614,8 +614,8 @@ static int arc_pmu_device_probe(struct platform_device *pdev)
 	/* loop thru all available h/w condition indexes */
 	for (i = 0; i < cc_bcr.c; i++) {
 		write_aux_reg(ARC_REG_CC_INDEX, i);
-		cc_name.indiv.word0 = read_aux_reg(ARC_REG_CC_NAME0);
+		cc_name.indiv.word0 = le32_to_cpu(read_aux_reg(ARC_REG_CC_NAME0));
-		cc_name.indiv.word1 = read_aux_reg(ARC_REG_CC_NAME1);
+		cc_name.indiv.word1 = le32_to_cpu(read_aux_reg(ARC_REG_CC_NAME1));
 
 		arc_pmu_map_hw_event(i, cc_name.str);
 		arc_pmu_add_raw_event_attr(i, cc_name.str);

arch/arm/Kconfig

@@ -82,7 +82,7 @@ config ARM
 	select HAVE_FAST_GUP if ARM_LPAE
 	select HAVE_FTRACE_MCOUNT_RECORD if !XIP_KERNEL
 	select HAVE_FUNCTION_GRAPH_TRACER if !THUMB2_KERNEL && !CC_IS_CLANG
-	select HAVE_FUNCTION_TRACER if !XIP_KERNEL
+	select HAVE_FUNCTION_TRACER if !XIP_KERNEL && (CC_IS_GCC || CLANG_VERSION >= 100000)
 	select HAVE_GCC_PLUGINS
 	select HAVE_HW_BREAKPOINT if PERF_EVENTS && (CPU_V6 || CPU_V6K || CPU_V7)
 	select HAVE_IDE if PCI || ISA || PCMCIA
@@ -1572,8 +1572,9 @@ config ARM_PATCH_IDIV
 	  code to do integer division.
 
 config AEABI
-	bool "Use the ARM EABI to compile the kernel" if !CPU_V7 && !CPU_V7M && !CPU_V6 && !CPU_V6K
+	bool "Use the ARM EABI to compile the kernel" if !CPU_V7 && \
-	default CPU_V7 || CPU_V7M || CPU_V6 || CPU_V6K
+		!CPU_V7M && !CPU_V6 && !CPU_V6K && !CC_IS_CLANG
+	default CPU_V7 || CPU_V7M || CPU_V6 || CPU_V6K || CC_IS_CLANG
 	help
 	  This option allows for the kernel to be compiled using the latest
 	  ARM ABI (aka EABI).  This is only useful if you are using a user

arch/arm/Makefile

@@ -112,6 +112,10 @@ ifeq ($(CONFIG_ARM_UNWIND),y)
 CFLAGS_ABI	+=-funwind-tables
 endif
 
+ifeq ($(CONFIG_CC_IS_CLANG),y)
+CFLAGS_ABI	+= -meabi gnu
+endif
+
 # Accept old syntax despite ".syntax unified"
 AFLAGS_NOWARN	:=$(call as-option,-Wa$(comma)-mno-warn-deprecated,-Wa$(comma)-W)
 

arch/arm/boot/dts/Makefile

@@ -1,4 +1,18 @@
 # SPDX-License-Identifier: GPL-2.0
+
+dtb-$(CONFIG_ARCH_BCM2835) += \
+	bcm2708-rpi-b.dtb \
+	bcm2708-rpi-b-plus.dtb \
+	bcm2708-rpi-cm.dtb \
+	bcm2708-rpi-zero.dtb \
+	bcm2708-rpi-zero-w.dtb \
+	bcm2709-rpi-2-b.dtb \
+	bcm2710-rpi-2-b.dtb \
+	bcm2710-rpi-3-b.dtb \
+	bcm2711-rpi-4-b.dtb \
+	bcm2710-rpi-3-b-plus.dtb \
+	bcm2710-rpi-cm3.dtb
+
 dtb-$(CONFIG_ARCH_ALPINE) += \
 	alpine-db.dtb
 dtb-$(CONFIG_MACH_ARTPEC6) += \
@@ -83,6 +97,7 @@ dtb-$(CONFIG_ARCH_BCM2835) += \
 	bcm2837-rpi-3-b.dtb \
 	bcm2837-rpi-3-b-plus.dtb \
 	bcm2837-rpi-cm3-io3.dtb \
+	bcm2838-rpi-4-b.dtb \
 	bcm2835-rpi-zero.dtb \
 	bcm2835-rpi-zero-w.dtb
 dtb-$(CONFIG_ARCH_BCM_5301X) += \
@@ -1286,3 +1301,13 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
 	aspeed-bmc-opp-zaius.dtb \
 	aspeed-bmc-portwell-neptune.dtb \
 	aspeed-bmc-quanta-q71l.dtb
+
+targets += dtbs dtbs_install
+targets += $(dtb-y)
+
+subdir-y	:= overlays
+
+# Enable fixups to support overlays on BCM2835 platforms
+ifeq ($(CONFIG_ARCH_BCM2835),y)
+	DTC_FLAGS ?= -@
+endif

arch/arm/boot/dts/am335x-icev2.dts

@@ -432,7 +432,7 @@
 	pinctrl-0 = <&mmc0_pins_default>;
 };
 
-&gpio0 {
+&gpio0_target {
 	/* Do not idle the GPIO used for holding the VTT regulator */
 	ti,no-reset-on-init;
 	ti,no-idle-on-init;

arch/arm/boot/dts/am33xx-l4.dtsi

@@ -127,7 +127,7 @@
 			ranges = <0x0 0x5000 0x1000>;
 		};
 
-		target-module@7000 {			/* 0x44e07000, ap 14 20.0 */
+		gpio0_target: target-module@7000 {	/* 0x44e07000, ap 14 20.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
 			ti,hwmods = "gpio1";
 			reg = <0x7000 0x4>,
@@ -2038,7 +2038,9 @@
 			reg = <0xe000 0x4>,
 			      <0xe054 0x4>;
 			reg-names = "rev", "sysc";
-			ti,sysc-midle ;
+			ti,sysc-midle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
 			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
 					<SYSC_IDLE_NO>,
 					<SYSC_IDLE_SMART>;

arch/arm/boot/dts/am3517-evm.dts

@@ -124,10 +124,11 @@
 	};
 
 	lcd0: display@0 {
-		compatible = "panel-dpi";
+		/* This isn't the exact LCD, but the timings meet spec */
+		/* To make it work, set CONFIG_OMAP2_DSS_MIN_FCK_PER_PCK=4 */
+		compatible = "newhaven,nhd-4.3-480272ef-atxl";
 		label = "15";
-		status = "okay";
+		backlight = <&bl>;
-		pinctrl-names = "default";
 		enable-gpios = <&gpio6 16 GPIO_ACTIVE_HIGH>;	/* gpio176, lcd INI */
 		vcc-supply = <&vdd_io_reg>;
 
@@ -136,22 +137,6 @@
 				remote-endpoint = <&dpi_out>;
 			};
 		};
-
-		panel-timing {
-			clock-frequency = <9000000>;
-			hactive = <480>;
-			vactive = <272>;
-			hfront-porch = <3>;
-			hback-porch = <2>;
-			hsync-len = <42>;
-			vback-porch = <3>;
-			vfront-porch = <4>;
-			vsync-len = <11>;
-			hsync-active = <0>;
-			vsync-active = <0>;
-			de-active = <1>;
-			pixelclk-active = <1>;
-		};
 	};
 
 	bl: backlight {

arch/arm/boot/dts/am3874-iceboard.dts

@@ -111,13 +111,13 @@
 		reg = <0x70>;
 		#address-cells = <1>;
 		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
 
 		i2c@0 {
 			/* FMC A */
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0>;
-			i2c-mux-idle-disconnect;
 		};
 
 		i2c@1 {
@@ -125,7 +125,6 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <1>;
-			i2c-mux-idle-disconnect;
 		};
 
 		i2c@2 {
@@ -133,7 +132,6 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <2>;
-			i2c-mux-idle-disconnect;
 		};
 
 		i2c@3 {
@@ -141,7 +139,6 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <3>;
-			i2c-mux-idle-disconnect;
 		};
 
 		i2c@4 {
@@ -149,14 +146,12 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <4>;
-			i2c-mux-idle-disconnect;
 		};
 
 		i2c@5 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <5>;
-			i2c-mux-idle-disconnect;
 
 			ina230@40 { compatible = "ti,ina230"; reg = <0x40>; shunt-resistor = <5000>; };
 			ina230@41 { compatible = "ti,ina230"; reg = <0x41>; shunt-resistor = <5000>; };
@@ -182,14 +177,12 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <6>;
-			i2c-mux-idle-disconnect;
 		};
 
 		i2c@7 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <7>;
-			i2c-mux-idle-disconnect;
 
 			u41: pca9575@20 {
 				compatible = "nxp,pca9575";

arch/arm/boot/dts/am4372.dtsi

@@ -337,6 +337,8 @@
 				ti,hwmods = "dss_dispc";
 				clocks = <&disp_clk>;
 				clock-names = "fck";
+
+				max-memory-bandwidth = <230000000>;
 			};
 
 			rfbi: rfbi@4832a800 {

arch/arm/boot/dts/bcm2708-rpi-b-plus.dts

@@ -0,0 +1,125 @@
+/dts-v1/;
+
+#include "bcm2708.dtsi"
+#include "bcm2708-rpi.dtsi"
+#include "bcm283x-rpi-smsc9514.dtsi"
+#include "bcm283x-rpi-csi1-2lane.dtsi"
+
+/ {
+	compatible = "raspberrypi,model-b-plus", "brcm,bcm2835";
+	model = "Raspberry Pi Model B+";
+};
+
+&gpio {
+	spi0_pins: spi0_pins {
+		brcm,pins = <9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_cs_pins: spi0_cs_pins {
+		brcm,pins = <8 7>;
+		brcm,function = <1>; /* output */
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+
+	i2s_pins: i2s {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	audio_pins: audio_pins {
+		brcm,pins = <40 45>;
+		brcm,function = <4>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
+	cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
+
+	spidev0: spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+
+	spidev1: spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "mmc0";
+		gpios = <&gpio 47 0>;
+	};
+
+	pwr_led: pwr {
+		label = "led1";
+		linux,default-trigger = "input";
+		gpios = <&gpio 35 0>;
+	};
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+};
+
+&audio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&audio_pins>;
+};
+
+/ {
+	__overrides__ {
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+
+		pwr_led_gpio = <&pwr_led>,"gpios:4";
+		pwr_led_activelow = <&pwr_led>,"gpios:8";
+		pwr_led_trigger = <&pwr_led>,"linux,default-trigger";
+	};
+};

arch/arm/boot/dts/bcm2708-rpi-b.dts

@@ -0,0 +1,115 @@
+/dts-v1/;
+
+#include "bcm2708.dtsi"
+#include "bcm2708-rpi.dtsi"
+#include "bcm283x-rpi-smsc9512.dtsi"
+#include "bcm283x-rpi-csi1-2lane.dtsi"
+
+/ {
+	compatible = "raspberrypi,model-b", "brcm,bcm2835";
+	model = "Raspberry Pi Model B";
+};
+
+&gpio {
+	spi0_pins: spi0_pins {
+		brcm,pins = <9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_cs_pins: spi0_cs_pins {
+		brcm,pins = <8 7>;
+		brcm,function = <1>; /* output */
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+
+	i2s_pins: i2s {
+		brcm,pins = <28 29 30 31>;
+		brcm,function = <6>; /* alt2 */
+	};
+
+	audio_pins: audio_pins {
+		brcm,pins = <40 45>;
+		brcm,function = <4>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
+	cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
+
+	spidev0: spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+
+	spidev1: spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "mmc0";
+		gpios = <&gpio 16 1>;
+	};
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
+};
+
+&audio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&audio_pins>;
+};
+
+/ {
+	__overrides__ {
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+	};
+};

arch/arm/boot/dts/bcm2708-rpi-cm.dts

@@ -0,0 +1,98 @@
+/dts-v1/;
+
+#include "bcm2708-rpi-cm.dtsi"
+#include "bcm283x-rpi-csi0-2lane.dtsi"
+#include "bcm283x-rpi-csi1-4lane.dtsi"
+
+/ {
+	compatible = "raspberrypi,compute-module", "brcm,bcm2835";
+	model = "Raspberry Pi Compute Module";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&gpio {
+	spi0_pins: spi0_pins {
+		brcm,pins = <9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_cs_pins: spi0_cs_pins {
+		brcm,pins = <8 7>;
+		brcm,function = <1>; /* output */
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+
+	i2s_pins: i2s {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	audio_pins: audio_pins {
+		brcm,pins;
+		brcm,function;
+	};
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
+	cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
+
+	spidev0: spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+
+	spidev1: spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+&audio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&audio_pins>;
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
+};

arch/arm/boot/dts/bcm2708-rpi-cm.dtsi

@@ -0,0 +1,18 @@
+#include "bcm2708.dtsi"
+#include "bcm2708-rpi.dtsi"
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "mmc0";
+		gpios = <&gpio 47 0>;
+	};
+};
+
+/ {
+	__overrides__ {
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+	};
+};

arch/arm/boot/dts/bcm2708-rpi-zero-w.dts

@@ -0,0 +1,163 @@
+/dts-v1/;
+
+#include "bcm2708.dtsi"
+#include "bcm2708-rpi.dtsi"
+#include "bcm283x-rpi-csi1-2lane.dtsi"
+
+/ {
+	compatible = "raspberrypi,model-zero-w", "brcm,bcm2835";
+	model = "Raspberry Pi Zero W";
+
+	chosen {
+		bootargs = "coherent_pool=1M 8250.nr_uarts=1";
+	};
+
+	aliases {
+		serial0 = &uart1;
+		serial1 = &uart0;
+		mmc1 = &mmcnr;
+	};
+};
+
+&gpio {
+	spi0_pins: spi0_pins {
+		brcm,pins = <9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_cs_pins: spi0_cs_pins {
+		brcm,pins = <8 7>;
+		brcm,function = <1>; /* output */
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+
+	i2s_pins: i2s {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	sdio_pins: sdio_pins {
+		brcm,pins = <34 35 36 37 38 39>;
+		brcm,function = <7>; /* ALT3 = SD1 */
+		brcm,pull = <0 2 2 2 2 2>;
+	};
+
+	bt_pins: bt_pins {
+		brcm,pins = <43>;
+		brcm,function = <4>; /* alt0:GPCLK2 */
+		brcm,pull = <0>; /* none */
+	};
+
+	uart0_pins: uart0_pins {
+		brcm,pins = <30 31 32 33>;
+		brcm,function = <7>; /* alt3=UART0 */
+		brcm,pull = <2 0 0 2>; /* up none none up */
+	};
+
+	uart1_pins: uart1_pins {
+		brcm,pins;
+		brcm,function;
+		brcm,pull;
+	};
+
+	audio_pins: audio_pins {
+		brcm,pins = <>;
+		brcm,function = <>;
+	};
+};
+
+&mmcnr {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdio_pins>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins &bt_pins>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
+	cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
+
+	spidev0: spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+
+	spidev1: spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "mmc0";
+		gpios = <&gpio 47 0>;
+	};
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+};
+
+&audio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&audio_pins>;
+};
+
+/ {
+	__overrides__ {
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+	};
+};

arch/arm/boot/dts/bcm2708-rpi-zero.dts

@@ -0,0 +1,118 @@
+/dts-v1/;
+
+#include "bcm2708.dtsi"
+#include "bcm2708-rpi.dtsi"
+#include "bcm283x-rpi-csi1-2lane.dtsi"
+
+/ {
+	compatible = "raspberrypi,model-zero", "brcm,bcm2835";
+	model = "Raspberry Pi Zero";
+
+	chosen {
+		bootargs = "coherent_pool=1M";
+	};
+};
+
+&gpio {
+	spi0_pins: spi0_pins {
+		brcm,pins = <9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_cs_pins: spi0_cs_pins {
+		brcm,pins = <8 7>;
+		brcm,function = <1>; /* output */
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+
+	i2s_pins: i2s {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	audio_pins: audio_pins {
+		brcm,pins = <>;
+		brcm,function = <>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
+	cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
+
+	spidev0: spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+
+	spidev1: spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "mmc0";
+		gpios = <&gpio 47 0>;
+	};
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+};
+
+&audio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&audio_pins>;
+};
+
+/ {
+	__overrides__ {
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+	};
+};

arch/arm/boot/dts/bcm2708-rpi.dtsi

@@ -0,0 +1,154 @@
+/* Downstream modifications to bcm2835-rpi.dtsi */
+
+#include "bcm2835-rpi.dtsi"
+
+/ {
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0>;
+	};
+
+	aliases {
+		audio = &audio;
+		aux = &aux;
+		sound = &sound;
+		soc = &soc;
+		dma = &dma;
+		intc = &intc;
+		watchdog = &watchdog;
+		random = &random;
+		mailbox = &mailbox;
+		gpio = &gpio;
+		uart0 = &uart0;
+		sdhost = &sdhost;
+		mmc0 = &sdhost;
+		i2s = &i2s;
+		spi0 = &spi0;
+		i2c0 = &i2c0;
+		uart1 = &uart1;
+		spi1 = &spi1;
+		spi2 = &spi2;
+		mmc = &mmc;
+		mmc1 = &mmc;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
+		usb = &usb;
+		leds = &leds;
+		fb = &fb;
+		thermal = &thermal;
+		axiperf = &axiperf;
+	};
+
+	leds: leds {
+		compatible = "gpio-leds";
+	};
+
+	soc {
+		gpiomem {
+			compatible = "brcm,bcm2835-gpiomem";
+			reg = <0x7e200000 0x1000>;
+		};
+
+		fb: fb {
+			compatible = "brcm,bcm2708-fb";
+			firmware = <&firmware>;
+			status = "okay";
+		};
+
+		vcsm: vcsm {
+			compatible = "raspberrypi,bcm2835-vcsm";
+			firmware = <&firmware>;
+			status = "okay";
+		};
+
+		/* Onboard audio */
+		audio: audio {
+			compatible = "brcm,bcm2835-audio";
+			brcm,pwm-channels = <8>;
+			status = "disabled";
+		};
+
+		/* External sound card */
+		sound: sound {
+			status = "disabled";
+		};
+	};
+
+	__overrides__ {
+		cache_line_size;
+
+		uart0 = <&uart0>,"status";
+		uart1 = <&uart1>,"status";
+		i2s = <&i2s>,"status";
+		spi = <&spi0>,"status";
+		i2c0 = <&i2c0>,"status";
+		i2c1 = <&i2c1>,"status";
+		i2c2_iknowwhatimdoing = <&i2c2>,"status";
+		i2c0_baudrate = <&i2c0>,"clock-frequency:0";
+		i2c1_baudrate = <&i2c1>,"clock-frequency:0";
+		i2c2_baudrate = <&i2c2>,"clock-frequency:0";
+
+		audio = <&audio>,"status";
+		watchdog = <&watchdog>,"status";
+		random = <&random>,"status";
+		sd_overclock = <&sdhost>,"brcm,overclock-50:0";
+		sd_force_pio = <&sdhost>,"brcm,force-pio?";
+		sd_pio_limit = <&sdhost>,"brcm,pio-limit:0";
+		sd_debug     = <&sdhost>,"brcm,debug";
+		sdio_overclock = <&mmc>,"brcm,overclock-50:0",
+				 <&mmcnr>,"brcm,overclock-50:0";
+		axiperf      = <&axiperf>,"status";
+	};
+};
+
+&hdmi {
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "disabled";
+};
+
+&txp {
+	status = "disabled";
+};
+
+&i2c0 {
+	status = "disabled";
+};
+
+&i2c1 {
+	status = "disabled";
+};
+
+&i2c2 {
+	status = "disabled";
+};
+
+&clocks {
+	firmware = <&firmware>;
+};
+
+&sdhci {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_gpio48>;
+	bus-width = <4>;
+};
+
+sdhost_pins: &sdhost_gpio48 {
+	/* Add alias */
+};
+
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	brcm,overclock-50 = <0>;
+	brcm,pio-limit = <1>;
+	status = "okay";
+};
+
+&cpu_thermal {
+	/delete-node/ trips;
+};
+
+&vec {
+	status = "disabled";
+};

arch/arm/boot/dts/bcm2708.dtsi

@@ -0,0 +1,10 @@
+#include "bcm2835.dtsi"
+#include "bcm270x.dtsi"
+
+/ {
+	/delete-node/ cpus;
+
+	__overrides__ {
+		arm_freq;
+	};
+};

arch/arm/boot/dts/bcm2709-rpi-2-b.dts

@@ -0,0 +1,125 @@
+/dts-v1/;
+
+#include "bcm2709.dtsi"
+#include "bcm2709-rpi.dtsi"
+#include "bcm283x-rpi-smsc9514.dtsi"
+#include "bcm283x-rpi-csi1-2lane.dtsi"
+
+/ {
+	compatible = "raspberrypi,2-model-b", "brcm,bcm2836";
+	model = "Raspberry Pi 2 Model B";
+};
+
+&gpio {
+	spi0_pins: spi0_pins {
+		brcm,pins = <9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_cs_pins: spi0_cs_pins {
+		brcm,pins = <8 7>;
+		brcm,function = <1>; /* output */
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+
+	i2s_pins: i2s {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	audio_pins: audio_pins {
+		brcm,pins = <40 45>;
+		brcm,function = <4>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
+	cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
+
+	spidev0: spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+
+	spidev1: spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "mmc0";
+		gpios = <&gpio 47 0>;
+	};
+
+	pwr_led: pwr {
+		label = "led1";
+		linux,default-trigger = "input";
+		gpios = <&gpio 35 0>;
+	};
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+};
+
+&audio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&audio_pins>;
+};
+
+/ {
+	__overrides__ {
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+
+		pwr_led_gpio = <&pwr_led>,"gpios:4";
+		pwr_led_activelow = <&pwr_led>,"gpios:8";
+		pwr_led_trigger = <&pwr_led>,"linux,default-trigger";
+	};
+};

arch/arm/boot/dts/bcm2709-rpi.dtsi

@@ -0,0 +1,5 @@
+#include "bcm2708-rpi.dtsi"
+
+&vchiq {
+	compatible = "brcm,bcm2836-vchiq", "brcm,bcm2835-vchiq";
+};

arch/arm/boot/dts/bcm2709.dtsi

@@ -0,0 +1,18 @@
+#include "bcm2836.dtsi"
+#include "bcm270x.dtsi"
+
+/ {
+	soc {
+		ranges = <0x7e000000 0x3f000000 0x01000000>,
+		         <0x40000000 0x40000000 0x00040000>;
+
+		/delete-node/ timer@7e003000;
+	};
+
+	__overrides__ {
+		arm_freq = <&v7_cpu0>, "clock-frequency:0",
+			   <&v7_cpu1>, "clock-frequency:0",
+			   <&v7_cpu2>, "clock-frequency:0",
+			   <&v7_cpu3>, "clock-frequency:0";
+	};
+};

arch/arm/boot/dts/bcm270x.dtsi

@@ -0,0 +1,165 @@
+/* Downstream bcm283x.dtsi diff */
+#include <dt-bindings/power/raspberrypi-power.h>
+
+/ {
+	chosen {
+		bootargs = "coherent_pool=1M";
+		/delete-property/ stdout-path;
+	};
+
+	soc: soc {
+
+		watchdog: watchdog@7e100000 {
+			/* Add label */
+		};
+
+		random: rng@7e104000 {
+			/* Add label */
+		};
+
+		gpio@7e200000 { /* gpio */
+			interrupts = <2 17>, <2 18>;
+
+			dpi_18bit_gpio0: dpi_18bit_gpio0 {
+				brcm,pins = <0 1 2 3 4 5 6 7 8 9 10 11
+					     12 13 14 15 16 17 18 19
+					     20 21>;
+				brcm,function = <BCM2835_FSEL_ALT2>;
+			};
+		};
+
+		serial@7e201000 { /* uart0 */
+			/* Enable CTS bug workaround */
+			cts-event-workaround;
+		};
+
+		i2s@7e203000 { /* i2s */
+			#sound-dai-cells = <0>;
+			reg = <0x7e203000 0x24>;
+			clocks = <&clocks BCM2835_CLOCK_PCM>;
+		};
+
+		spi0: spi@7e204000 {
+			/* Add label */
+			dmas = <&dma 6>, <&dma 7>;
+			dma-names = "tx", "rx";
+		};
+
+		pixelvalve0: pixelvalve@7e206000 {
+			/* Add label */
+			status = "disabled";
+		};
+
+		pixelvalve1: pixelvalve@7e207000 {
+			/* Add label */
+			status = "disabled";
+		};
+
+		dpi: dpi@7e208000 {
+			compatible = "brcm,bcm2835-dpi";
+			reg = <0x7e208000 0x8c>;
+			clocks = <&clocks BCM2835_CLOCK_VPU>,
+				 <&clocks BCM2835_CLOCK_DPI>;
+			clock-names = "core", "pixel";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		/delete-node/ sdhci@7e300000;
+
+		sdhci: mmc: mmc@7e300000 {
+			compatible = "brcm,bcm2835-mmc", "brcm,bcm2835-sdhci";
+			reg = <0x7e300000 0x100>;
+			interrupts = <2 30>;
+			clocks = <&clocks BCM2835_CLOCK_EMMC>;
+			dmas = <&dma 11>;
+			dma-names = "rx-tx";
+			brcm,overclock-50 = <0>;
+			status = "disabled";
+		};
+
+		/* A clone of mmc but with non-removable set */
+		mmcnr: mmcnr@7e300000 {
+			compatible = "brcm,bcm2835-mmc", "brcm,bcm2835-sdhci";
+			reg = <0x7e300000 0x100>;
+			interrupts = <2 30>;
+			clocks = <&clocks BCM2835_CLOCK_EMMC>;
+			dmas = <&dma 11>;
+			dma-names = "rx-tx";
+			brcm,overclock-50 = <0>;
+			non-removable;
+			status = "disabled";
+		};
+
+		hvs: hvs@7e400000 {
+			/* Add label */
+			status = "disabled";
+		};
+
+		firmwarekms: firmwarekms@7e600000 {
+			compatible = "raspberrypi,rpi-firmware-kms";
+			/* SMI interrupt reg */
+			reg = <0x7e600000 0x100>;
+			interrupts = <2 16>;
+			brcm,firmware = <&firmware>;
+			status = "disabled";
+		};
+
+		smi: smi@7e600000 {
+			compatible = "brcm,bcm2835-smi";
+			reg = <0x7e600000 0x100>;
+			interrupts = <2 16>;
+			clocks = <&clocks BCM2835_CLOCK_SMI>;
+			assigned-clocks = <&clocks BCM2835_CLOCK_SMI>;
+			assigned-clock-rates = <125000000>;
+			dmas = <&dma 4>;
+			dma-names = "rx-tx";
+			status = "disabled";
+		};
+
+		pixelvalve2: pixelvalve@7e807000 {
+			/* Add label */
+			status = "disabled";
+		};
+
+		hdmi@7e902000 { /* hdmi */
+			status = "disabled";
+		};
+
+		usb@7e980000 { /* usb */
+			compatible = "brcm,bcm2708-usb";
+			reg = <0x7e980000 0x10000>,
+			      <0x7e006000 0x1000>;
+			interrupt-names = "usb",
+					  "soft";
+			interrupts = <1 9>,
+				     <2 0>;
+		};
+
+		v3d@7ec00000 { /* vd3 */
+			compatible = "brcm,vc4-v3d";
+			power-domains = <&power RPI_POWER_DOMAIN_V3D>;
+			status = "disabled";
+		};
+
+		axiperf: axiperf {
+			compatible = "brcm,bcm2835-axiperf";
+			reg = <0x7e009800 0x100>,
+			      <0x7ee08000 0x100>;
+			firmware = <&firmware>;
+			status = "disabled";
+		};
+	};
+
+	__overrides__ {
+		cam0-pwdn-ctrl;
+		cam0-pwdn;
+		cam0-led-ctrl;
+		cam0-led;
+	};
+};
+
+&vc4 {
+	status = "disabled";
+};

arch/arm/boot/dts/bcm2710-rpi-2-b.dts

@@ -0,0 +1,125 @@
+/dts-v1/;
+
+#include "bcm2710.dtsi"
+#include "bcm2709-rpi.dtsi"
+#include "bcm283x-rpi-smsc9514.dtsi"
+#include "bcm283x-rpi-csi1-2lane.dtsi"
+
+/ {
+	compatible = "raspberrypi,2-model-b-rev2", "brcm,bcm2837";
+	model = "Raspberry Pi 2 Model B rev 1.2";
+};
+
+&gpio {
+	spi0_pins: spi0_pins {
+		brcm,pins = <9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_cs_pins: spi0_cs_pins {
+		brcm,pins = <8 7>;
+		brcm,function = <1>; /* output */
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+
+	i2s_pins: i2s {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	audio_pins: audio_pins {
+		brcm,pins = <40 45>;
+		brcm,function = <4>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
+	cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
+
+	spidev0: spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+
+	spidev1: spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "mmc0";
+		gpios = <&gpio 47 0>;
+	};
+
+	pwr_led: pwr {
+		label = "led1";
+		linux,default-trigger = "input";
+		gpios = <&gpio 35 0>;
+	};
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+};
+
+&audio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&audio_pins>;
+};
+
+/ {
+	__overrides__ {
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+
+		pwr_led_gpio = <&pwr_led>,"gpios:4";
+		pwr_led_activelow = <&pwr_led>,"gpios:8";
+		pwr_led_trigger = <&pwr_led>,"linux,default-trigger";
+	};
+};

arch/arm/boot/dts/bcm2710-rpi-3-b-plus.dts

@@ -0,0 +1,183 @@
+/dts-v1/;
+
+#include "bcm2710.dtsi"
+#include "bcm2709-rpi.dtsi"
+#include "bcm283x-rpi-lan7515.dtsi"
+#include "bcm283x-rpi-csi1-2lane.dtsi"
+
+/ {
+	compatible = "raspberrypi,3-model-b-plus", "brcm,bcm2837";
+	model = "Raspberry Pi 3 Model B+";
+
+	chosen {
+		bootargs = "coherent_pool=1M 8250.nr_uarts=1";
+	};
+
+	aliases {
+		serial0 = &uart1;
+		serial1 = &uart0;
+		mmc1 = &mmcnr;
+	};
+};
+
+&gpio {
+	spi0_pins: spi0_pins {
+		brcm,pins = <9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_cs_pins: spi0_cs_pins {
+		brcm,pins = <8 7>;
+		brcm,function = <1>; /* output */
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+
+	i2s_pins: i2s {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	sdio_pins: sdio_pins {
+		brcm,pins =     <34 35 36 37 38 39>;
+		brcm,function = <7>; // alt3 = SD1
+		brcm,pull =     <0 2 2 2 2 2>;
+	};
+
+	bt_pins: bt_pins {
+		brcm,pins = <43>;
+		brcm,function = <4>; /* alt0:GPCLK2 */
+		brcm,pull = <0>;
+	};
+
+	uart0_pins: uart0_pins {
+		brcm,pins = <32 33>;
+		brcm,function = <7>; /* alt3=UART0 */
+		brcm,pull = <0 2>;
+	};
+
+	uart1_pins: uart1_pins {
+		brcm,pins;
+		brcm,function;
+		brcm,pull;
+	};
+
+	audio_pins: audio_pins {
+		brcm,pins = <40 41>;
+		brcm,function = <4>;
+	};
+};
+
+&mmcnr {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdio_pins>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&firmware {
+	expgpio: expgpio {
+		compatible = "raspberrypi,firmware-gpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+		status = "okay";
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins &bt_pins>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
+	cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
+
+	spidev0: spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+
+	spidev1: spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "mmc0";
+		gpios = <&gpio 29 0>;
+	};
+
+	pwr_led: pwr {
+		label = "led1";
+		linux,default-trigger = "default-on";
+		gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
+};
+
+&audio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&audio_pins>;
+};
+
+/ {
+	__overrides__ {
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+
+		pwr_led_gpio = <&pwr_led>,"gpios:4";
+		pwr_led_activelow = <&pwr_led>,"gpios:8";
+		pwr_led_trigger = <&pwr_led>,"linux,default-trigger";
+	};
+};

arch/arm/boot/dts/bcm2710-rpi-3-b.dts

@@ -0,0 +1,194 @@
+/dts-v1/;
+
+#include "bcm2710.dtsi"
+#include "bcm2709-rpi.dtsi"
+#include "bcm283x-rpi-smsc9514.dtsi"
+#include "bcm283x-rpi-csi1-2lane.dtsi"
+
+/ {
+	compatible = "raspberrypi,3-model-b", "brcm,bcm2837";
+	model = "Raspberry Pi 3 Model B";
+
+	chosen {
+		bootargs = "coherent_pool=1M 8250.nr_uarts=1";
+	};
+
+	aliases {
+		serial0 = &uart1;
+		serial1 = &uart0;
+		mmc1 = &mmcnr;
+	};
+};
+
+&gpio {
+	spi0_pins: spi0_pins {
+		brcm,pins = <9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_cs_pins: spi0_cs_pins {
+		brcm,pins = <8 7>;
+		brcm,function = <1>; /* output */
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+
+	i2s_pins: i2s {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	sdio_pins: sdio_pins {
+		brcm,pins =     <34 35 36 37 38 39>;
+		brcm,function = <7>; // alt3 = SD1
+		brcm,pull =     <0 2 2 2 2 2>;
+	};
+
+	bt_pins: bt_pins {
+		brcm,pins = <43>;
+		brcm,function = <4>; /* alt0:GPCLK2 */
+		brcm,pull = <0>;
+	};
+
+	uart0_pins: uart0_pins {
+		brcm,pins = <32 33>;
+		brcm,function = <7>; /* alt3=UART0 */
+		brcm,pull = <0 2>;
+	};
+
+	uart1_pins: uart1_pins {
+		brcm,pins;
+		brcm,function;
+		brcm,pull;
+	};
+
+	audio_pins: audio_pins {
+		brcm,pins = <40 41>;
+		brcm,function = <4>;
+	};
+};
+
+&mmcnr {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdio_pins>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&soc {
+	virtgpio: virtgpio {
+		compatible = "brcm,bcm2835-virtgpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+		firmware = <&firmware>;
+		status = "okay";
+	};
+
+};
+
+&firmware {
+	expgpio: expgpio {
+		compatible = "raspberrypi,firmware-gpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+		status = "okay";
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins &bt_pins>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
+	cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
+
+	spidev0: spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+
+	spidev1: spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "mmc0";
+		gpios = <&virtgpio 0 0>;
+	};
+
+	pwr_led: pwr {
+		label = "led1";
+		linux,default-trigger = "input";
+		gpios = <&expgpio 7 0>;
+	};
+};
+
+&hdmi {
+	hpd-gpios = <&expgpio 4 GPIO_ACTIVE_LOW>;
+};
+
+&audio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&audio_pins>;
+};
+
+/ {
+	__overrides__ {
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+
+		pwr_led_gpio = <&pwr_led>,"gpios:4";
+		pwr_led_activelow = <&pwr_led>,"gpios:8";
+		pwr_led_trigger = <&pwr_led>,"linux,default-trigger";
+	};
+};

arch/arm/boot/dts/bcm2710-rpi-cm3.dts

@@ -0,0 +1,135 @@
+/dts-v1/;
+
+#include "bcm2710.dtsi"
+#include "bcm2709-rpi.dtsi"
+#include "bcm283x-rpi-csi0-2lane.dtsi"
+#include "bcm283x-rpi-csi1-4lane.dtsi"
+
+/ {
+	compatible = "raspberrypi,3-compute-module", "brcm,bcm2837";
+	model = "Raspberry Pi Compute Module 3";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&gpio {
+	spi0_pins: spi0_pins {
+		brcm,pins = <9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_cs_pins: spi0_cs_pins {
+		brcm,pins = <8 7>;
+		brcm,function = <1>; /* output */
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+
+	i2s_pins: i2s {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	audio_pins: audio_pins {
+		brcm,pins;
+		brcm,function;
+	};
+};
+
+&soc {
+	virtgpio: virtgpio {
+		compatible = "brcm,bcm2835-virtgpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+		firmware = <&firmware>;
+		status = "okay";
+	};
+
+};
+
+&firmware {
+	expgpio: expgpio {
+		compatible = "raspberrypi,firmware-gpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+		status = "okay";
+	};
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
+	cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
+
+	spidev0: spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+
+	spidev1: spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "mmc0";
+		gpios = <&virtgpio 0 0>;
+	};
+};
+
+&hdmi {
+	hpd-gpios = <&expgpio 0 GPIO_ACTIVE_LOW>;
+};
+
+&audio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&audio_pins>;
+};
+
+/ {
+	__overrides__ {
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+	};
+};

arch/arm/boot/dts/bcm2710.dtsi

@@ -0,0 +1,25 @@
+#include "bcm2837.dtsi"
+#include "bcm270x.dtsi"
+
+/ {
+	compatible = "brcm,bcm2837", "brcm,bcm2836";
+
+	arm-pmu {
+#ifdef RPI364
+		compatible = "arm,armv8-pmuv3", "arm,cortex-a7-pmu";
+#else
+		compatible = "arm,cortex-a7-pmu";
+#endif
+	};
+
+	soc {
+		/delete-node/ timer@7e003000;
+	};
+
+	__overrides__ {
+		arm_freq = <&cpu0>, "clock-frequency:0",
+		       <&cpu1>, "clock-frequency:0",
+		       <&cpu2>, "clock-frequency:0",
+		       <&cpu3>, "clock-frequency:0";
+	};
+};

arch/arm/boot/dts/bcm2711-rpi-4-b.dts

@@ -0,0 +1,338 @@
+/dts-v1/;
+
+#include "bcm2711.dtsi"
+#include "bcm2711-rpi.dtsi"
+#include "bcm283x-rpi-csi1-2lane.dtsi"
+
+/ {
+	compatible = "raspberrypi,4-model-b", "brcm,bcm2711";
+	model = "Raspberry Pi 4 Model B";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0>;
+	};
+
+	chosen {
+		bootargs = "coherent_pool=1M 8250.nr_uarts=1 cma=64M";
+	};
+
+	aliases {
+		serial0 = &uart1;
+		serial1 = &uart0;
+		mmc0 = &emmc2;
+		mmc1 = &mmcnr;
+		mmc2 = &sdhost;
+		i2c3 = &i2c3;
+		i2c4 = &i2c4;
+		i2c5 = &i2c5;
+		i2c6 = &i2c6;
+		/delete-property/ ethernet;
+		/delete-property/ intc;
+		ethernet0 = &genet;
+	};
+};
+
+&soc {
+	virtgpio: virtgpio {
+		compatible = "brcm,bcm2835-virtgpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+		firmware = <&firmware>;
+		status = "okay";
+	};
+};
+
+&mmcnr {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdio_pins>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&firmware {
+	expgpio: gpio {
+		compatible = "raspberrypi,firmware-gpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "BT_ON",
+				  "WL_ON",
+				  "PWR_LED_OFF",
+				  "GLOBAL_RESET",
+				  "VDD_SD_IO_SEL",
+				  "CAM_GPIO",
+				  "",
+				  "";
+		status = "okay";
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins &bt_pins>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
+	cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
+
+	spidev0: spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+
+	spidev1: spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+};
+
+// =============================================
+// Board specific stuff here
+
+/ {
+
+	sd_io_1v8_reg: sd_io_1v8_reg {
+		status = "okay";
+		compatible = "regulator-gpio";
+		vin-supply = <&vdd_5v0_reg>;
+		regulator-name = "vdd-sd-io";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+		regulator-settling-time-us = <5000>;
+
+		gpios = <&expgpio 4 GPIO_ACTIVE_HIGH>;
+		states = <1800000 0x1
+			  3300000 0x0>;
+	};
+};
+
+&sdhost {
+	status = "disabled";
+};
+
+&emmc2 {
+	status = "okay";
+	broken-cd;
+	vqmmc-supply = <&sd_io_1v8_reg>;
+};
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "mmc0";
+		gpios = <&gpio 42 GPIO_ACTIVE_HIGH>;
+	};
+
+	pwr_led: pwr {
+		label = "led1";
+		linux,default-trigger = "default-on";
+		gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&audio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&audio_pins>;
+};
+
+&sdhost_gpio48 {
+	brcm,pins = <22 23 24 25 26 27>;
+	brcm,function = <BCM2835_FSEL_ALT0>;
+};
+
+&gpio {
+	spi0_pins: spi0_pins {
+		brcm,pins = <9 10 11>;
+		brcm,function = <BCM2835_FSEL_ALT0>;
+	};
+
+	spi0_cs_pins: spi0_cs_pins {
+		brcm,pins = <8 7>;
+		brcm,function = <BCM2835_FSEL_GPIO_OUT>;
+	};
+
+	spi3_pins: spi3_pins {
+		brcm,pins = <1 2 3>;
+		brcm,function = <BCM2835_FSEL_ALT3>;
+	};
+
+	spi3_cs_pins: spi3_cs_pins {
+		brcm,pins = <0 24>;
+		brcm,function = <BCM2835_FSEL_GPIO_OUT>;
+	};
+
+	spi4_pins: spi4_pins {
+		brcm,pins = <5 6 7>;
+		brcm,function = <BCM2835_FSEL_ALT3>;
+	};
+
+	spi4_cs_pins: spi4_cs_pins {
+		brcm,pins = <4 25>;
+		brcm,function = <BCM2835_FSEL_GPIO_OUT>;
+	};
+
+	spi5_pins: spi5_pins {
+		brcm,pins = <13 14 15>;
+		brcm,function = <BCM2835_FSEL_ALT3>;
+	};
+
+	spi5_cs_pins: spi5_cs_pins {
+		brcm,pins = <12 26>;
+		brcm,function = <BCM2835_FSEL_GPIO_OUT>;
+	};
+
+	spi6_pins: spi6_pins {
+		brcm,pins = <19 20 21>;
+		brcm,function = <BCM2835_FSEL_ALT3>;
+	};
+
+	spi6_cs_pins: spi6_cs_pins {
+		brcm,pins = <18 27>;
+		brcm,function = <BCM2835_FSEL_GPIO_OUT>;
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <BCM2835_FSEL_ALT0>;
+		brcm,pull = <BCM2835_PUD_UP>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <BCM2835_FSEL_ALT0>;
+		brcm,pull = <BCM2835_PUD_UP>;
+	};
+
+	i2c3_pins: i2c3 {
+		brcm,pins = <4 5>;
+		brcm,function = <BCM2835_FSEL_ALT5>;
+		brcm,pull = <BCM2835_PUD_UP>;
+	};
+
+	i2c4_pins: i2c4 {
+		brcm,pins = <8 9>;
+		brcm,function = <BCM2835_FSEL_ALT5>;
+		brcm,pull = <BCM2835_PUD_UP>;
+	};
+
+	i2c5_pins: i2c5 {
+		brcm,pins = <12 13>;
+		brcm,function = <BCM2835_FSEL_ALT5>;
+		brcm,pull = <BCM2835_PUD_UP>;
+	};
+
+	i2c6_pins: i2c6 {
+		brcm,pins = <22 23>;
+		brcm,function = <BCM2835_FSEL_ALT5>;
+		brcm,pull = <BCM2835_PUD_UP>;
+	};
+
+	i2s_pins: i2s {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <BCM2835_FSEL_ALT0>;
+	};
+
+	sdio_pins: sdio_pins {
+		brcm,pins =     <34 35 36 37 38 39>;
+		brcm,function = <BCM2835_FSEL_ALT3>; // alt3 = SD1
+		brcm,pull =     <0 2 2 2 2 2>;
+	};
+
+	bt_pins: bt_pins {
+		brcm,pins = "-"; // non-empty to keep btuart happy, //4 = 0
+				 // to fool pinctrl
+		brcm,function = <0>;
+		brcm,pull = <2>;
+	};
+
+	uart0_pins: uart0_pins {
+		brcm,pins = <32 33>;
+		brcm,function = <BCM2835_FSEL_ALT3>;
+		brcm,pull = <0 2>;
+	};
+
+	uart1_pins: uart1_pins {
+		brcm,pins;
+		brcm,function;
+		brcm,pull;
+	};
+
+	uart2_pins: uart2_pins {
+		brcm,pins = <0 1>;
+		brcm,function = <BCM2835_FSEL_ALT4>;
+		brcm,pull = <0 2>;
+	};
+
+	uart3_pins: uart3_pins {
+		brcm,pins = <4 5>;
+		brcm,function = <BCM2835_FSEL_ALT4>;
+		brcm,pull = <0 2>;
+	};
+
+	uart4_pins: uart4_pins {
+		brcm,pins = <8 9>;
+		brcm,function = <BCM2835_FSEL_ALT4>;
+		brcm,pull = <0 2>;
+	};
+
+	uart5_pins: uart5_pins {
+		brcm,pins = <12 13>;
+		brcm,function = <BCM2835_FSEL_ALT4>;
+		brcm,pull = <0 2>;
+	};
+
+	audio_pins: audio_pins {
+		brcm,pins = <40 41>;
+		brcm,function = <4>;
+	};
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+/ {
+	__overrides__ {
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+
+		pwr_led_gpio = <&pwr_led>,"gpios:4";
+		pwr_led_activelow = <&pwr_led>,"gpios:8";
+		pwr_led_trigger = <&pwr_led>,"linux,default-trigger";
+	};
+};

arch/arm/boot/dts/bcm2711-rpi.dtsi

@@ -0,0 +1,7 @@
+#include "bcm2708-rpi.dtsi"
+#include "bcm2838-rpi.dtsi"
+
+&v3d {
+     /* Undo the overwriting by bcm270x.dtsi */
+     power-domains = <&pm BCM2835_POWER_DOMAIN_GRAFX_V3D>;
+};

arch/arm/boot/dts/bcm2711.dtsi

@@ -0,0 +1,44 @@
+#include "bcm2838.dtsi"
+#include "bcm270x.dtsi"
+
+/ {
+	soc {
+		/delete-node/ v3d@7ec00000;
+	};
+
+	__overrides__ {
+		arm_freq;
+	};
+};
+
+&v3d {
+	status = "disabled";
+};
+
+&firmwarekms {
+	interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&smi {
+	interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&mmc {
+	interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&mmcnr {
+	interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&usb {
+	reg = <0x7e980000 0x10000>,
+	      <0x7e00b200 0x200>;
+	interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&gpio {
+	interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
+};

arch/arm/boot/dts/bcm2835-common.dtsi

@@ -0,0 +1,54 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/* This include file covers the common peripherals and configuration between
+ * bcm2835, bcm2836 and bcm2837 implementations.
+ */
+
+/ {
+	soc {
+		timer@7e003000 {
+			compatible = "brcm,bcm2835-system-timer";
+			reg = <0x7e003000 0x1000>;
+			interrupts = <1 0>, <1 1>, <1 2>, <1 3>;
+			/* This could be a reference to BCM2835_CLOCK_TIMER,
+			 * but we don't have the driver using the common clock
+			 * support yet.
+			 */
+			clock-frequency = <1000000>;
+		};
+
+		intc: interrupt-controller@7e00b200 {
+			compatible = "brcm,bcm2835-armctrl-ic";
+			reg = <0x7e00b200 0x200>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		thermal: thermal@7e212000 {
+			compatible = "brcm,bcm2835-thermal";
+			reg = <0x7e212000 0x8>;
+			clocks = <&clocks BCM2835_CLOCK_TSENS>;
+			#thermal-sensor-cells = <0>;
+			status = "disabled";
+		};
+
+		v3d: v3d@7ec00000 {
+			compatible = "brcm,bcm2835-v3d";
+			reg = <0x7ec00000 0x1000>;
+			interrupts = <1 10>;
+			power-domains = <&pm BCM2835_POWER_DOMAIN_GRAFX_V3D>;
+		};
+	};
+};
+
+&gpio {
+	i2c_slave_gpio18: i2c_slave_gpio18 {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <BCM2835_FSEL_ALT3>;
+	};
+
+	jtag_gpio4: jtag_gpio4 {
+		brcm,pins = <4 5 6 12 13>;
+		brcm,function = <BCM2835_FSEL_ALT5>;
+	};
+};

arch/arm/boot/dts/bcm2835-rpi-a-plus.dts

@@ -3,6 +3,7 @@
 #include "bcm2835.dtsi"
 #include "bcm2835-rpi.dtsi"
 #include "bcm283x-rpi-usb-host.dtsi"
+#include "bcm283x-rpi-csi1-2lane.dtsi"
 
 / {
 	compatible = "raspberrypi,model-a-plus", "brcm,bcm2835";
@@ -99,6 +100,8 @@
 
 &hdmi {
 	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
 };
 
 &pwm {
@@ -107,6 +110,13 @@
 	status = "okay";
 };
 
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_gpio14>;

arch/arm/boot/dts/bcm2835-rpi-a.dts

@@ -3,6 +3,7 @@
 #include "bcm2835.dtsi"
 #include "bcm2835-rpi.dtsi"
 #include "bcm283x-rpi-usb-host.dtsi"
+#include "bcm283x-rpi-csi1-2lane.dtsi"
 
 / {
 	compatible = "raspberrypi,model-a", "brcm,bcm2835";
@@ -94,6 +95,8 @@
 
 &hdmi {
 	hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
 };
 
 &pwm {
@@ -102,6 +105,13 @@
 	status = "okay";
 };
 
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_gpio14>;

arch/arm/boot/dts/bcm2835-rpi-b-plus.dts

@@ -4,6 +4,7 @@
 #include "bcm2835-rpi.dtsi"
 #include "bcm283x-rpi-smsc9514.dtsi"
 #include "bcm283x-rpi-usb-host.dtsi"
+#include "bcm283x-rpi-csi1-2lane.dtsi"
 
 / {
 	compatible = "raspberrypi,model-b-plus", "brcm,bcm2835";
@@ -101,6 +102,8 @@
 
 &hdmi {
 	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
 };
 
 &pwm {
@@ -109,6 +112,13 @@
 	status = "okay";
 };
 
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_gpio14>;

arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts

@@ -4,6 +4,7 @@
 #include "bcm2835-rpi.dtsi"
 #include "bcm283x-rpi-smsc9512.dtsi"
 #include "bcm283x-rpi-usb-host.dtsi"
+#include "bcm283x-rpi-csi1-2lane.dtsi"
 
 / {
 	compatible = "raspberrypi,model-b-rev2", "brcm,bcm2835";
@@ -94,6 +95,8 @@
 
 &hdmi {
 	hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
 };
 
 &pwm {
@@ -102,6 +105,13 @@
 	status = "okay";
 };
 
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_gpio14>;

arch/arm/boot/dts/bcm2835-rpi-b.dts

@@ -4,6 +4,7 @@
 #include "bcm2835-rpi.dtsi"
 #include "bcm283x-rpi-smsc9512.dtsi"
 #include "bcm283x-rpi-usb-host.dtsi"
+#include "bcm283x-rpi-csi1-2lane.dtsi"
 
 / {
 	compatible = "raspberrypi,model-b", "brcm,bcm2835";
@@ -89,6 +90,8 @@
 
 &hdmi {
 	hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
 };
 
 &pwm {
@@ -97,6 +100,13 @@
 	status = "okay";
 };
 
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_gpio14>;

arch/arm/boot/dts/bcm2835-rpi-cm1-io1.dts

@@ -79,6 +79,15 @@
 
 &hdmi {
 	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
+};
+
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	status = "okay";
 };
 
 &uart0 {

arch/arm/boot/dts/bcm2835-rpi-zero-w.dts

@@ -100,12 +100,15 @@
 
 &hdmi {
 	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
 };
 
 &sdhci {
 	#address-cells = <1>;
 	#size-cells = <0>;
 	pinctrl-0 = <&emmc_gpio34 &gpclk2_gpio43>;
+	bus-width = <4>;
 	mmc-pwrseq = <&wifi_pwrseq>;
 	non-removable;
 	status = "okay";
@@ -116,6 +119,13 @@
 	};
 };
 
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_gpio32 &uart0_ctsrts_gpio30>;

arch/arm/boot/dts/bcm2835-rpi-zero.dts

@@ -7,6 +7,7 @@
 #include "bcm2835.dtsi"
 #include "bcm2835-rpi.dtsi"
 #include "bcm283x-rpi-usb-otg.dtsi"
+#include "bcm283x-rpi-csi1-2lane.dtsi"
 
 / {
 	compatible = "raspberrypi,model-zero", "brcm,bcm2835";
@@ -96,6 +97,15 @@
 
 &hdmi {
 	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
+};
+
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	status = "okay";
 };
 
 &uart0 {

arch/arm/boot/dts/bcm2835-rpi.dtsi

@@ -34,6 +34,22 @@
 			interrupts = <0 2>;
 		};
 	};
+
+	vdd_3v3_reg: fixedregulator_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	vdd_5v0_reg: fixedregulator_5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
 };
 
 &gpio {
@@ -68,19 +84,6 @@
 	status = "okay";
 };
 
-&sdhci {
-	pinctrl-names = "default";
-	pinctrl-0 = <&emmc_gpio48>;
-	bus-width = <4>;
-};
-
-&sdhost {
-	pinctrl-names = "default";
-	pinctrl-0 = <&sdhost_gpio48>;
-	status = "okay";
-	bus-width = <4>;
-};
-
 &usb {
 	power-domains = <&power RPI_POWER_DOMAIN_USB>;
 };
@@ -90,6 +93,10 @@
 	status = "okay";
 };
 
+&v3d {
+	power-domains = <&power RPI_POWER_DOMAIN_V3D>;
+};
+
 &vec {
 	power-domains = <&power RPI_POWER_DOMAIN_VEC>;
 	status = "okay";
@@ -102,3 +109,11 @@
 &dsi1 {
 	power-domains = <&power RPI_POWER_DOMAIN_DSI1>;
 };
+
+&csi0 {
+	power-domains = <&power RPI_POWER_DOMAIN_UNICAM0>;
+};
+
+&csi1 {
+	power-domains = <&power RPI_POWER_DOMAIN_UNICAM1>;
+};

arch/arm/boot/dts/bcm2835.dtsi

@@ -1,5 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0
 #include "bcm283x.dtsi"
+#include "bcm2835-common.dtsi"
 
 / {
 	compatible = "brcm,bcm2835";

arch/arm/boot/dts/bcm2836-rpi-2-b.dts

@@ -4,6 +4,7 @@
 #include "bcm2836-rpi.dtsi"
 #include "bcm283x-rpi-smsc9514.dtsi"
 #include "bcm283x-rpi-usb-host.dtsi"
+#include "bcm283x-rpi-csi1-2lane.dtsi"
 
 / {
 	compatible = "raspberrypi,2-model-b", "brcm,bcm2836";
@@ -105,6 +106,8 @@
 
 &hdmi {
 	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
 };
 
 &pwm {
@@ -113,6 +116,13 @@
 	status = "okay";
 };
 
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_gpio14>;

arch/arm/boot/dts/bcm2836.dtsi

@@ -1,5 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0
 #include "bcm283x.dtsi"
+#include "bcm2835-common.dtsi"
 
 / {
 	compatible = "brcm,bcm2836";

arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts

@@ -124,6 +124,8 @@
 
 &hdmi {
 	hpd-gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
 };
 
 &pwm {

arch/arm/boot/dts/bcm2837-rpi-3-b.dts

@@ -4,6 +4,7 @@
 #include "bcm2836-rpi.dtsi"
 #include "bcm283x-rpi-smsc9514.dtsi"
 #include "bcm283x-rpi-usb-host.dtsi"
+#include "bcm283x-rpi-csi1-2lane.dtsi"
 
 / {
 	compatible = "raspberrypi,3-model-b", "brcm,bcm2837";
@@ -125,6 +126,8 @@
 
 &hdmi {
 	hpd-gpios = <&expgpio 4 GPIO_ACTIVE_LOW>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
 };
 
 /* uart0 communicates with the BT module */

arch/arm/boot/dts/bcm2837-rpi-cm3.dtsi

@@ -8,6 +8,14 @@
 		reg = <0 0x40000000>;
 	};
 
+	leds {
+		/*
+		 * Since there is no upstream GPIO driver yet,
+		 * remove the incomplete node.
+		 */
+		/delete-node/ act;
+	};
+
 	reg_3v3: fixed-regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "3V3";

arch/arm/boot/dts/bcm2837.dtsi

@@ -1,4 +1,5 @@
 #include "bcm283x.dtsi"
+#include "bcm2835-common.dtsi"
 
 / {
 	compatible = "brcm,bcm2837";

arch/arm/boot/dts/bcm2838-rpi-4-b.dts

@@ -0,0 +1,118 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2838.dtsi"
+#include "bcm2835-rpi.dtsi"
+#include "bcm2838-rpi.dtsi"
+
+/ {
+	compatible = "raspberrypi,4-model-b", "brcm,bcm2711";
+	model = "Raspberry Pi 4 Model B";
+
+	chosen {
+		/* 8250 auxiliary UART instead of pl011 */
+		stdout-path = "serial1:115200n8";
+	};
+
+	memory@0 {
+		reg = <0 0 0x40000000>;
+	};
+
+	leds {
+		act {
+			gpios = <&gpio 42 GPIO_ACTIVE_HIGH>;
+		};
+
+		pwr {
+			label = "PWR";
+			gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
+	};
+
+	sd_io_1v8_reg: sd_io_1v8_reg {
+		status = "okay";
+		compatible = "regulator-gpio";
+		vin-supply = <&vdd_5v0_reg>;
+		regulator-name = "vdd-sd-io";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+		regulator-settling-time-us = <5000>;
+
+		gpios = <&expgpio 4 GPIO_ACTIVE_HIGH>;
+		states = <1800000 0x1
+			  3300000 0x0>;
+	};
+};
+
+&firmware {
+	expgpio: gpio {
+		compatible = "raspberrypi,firmware-gpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "BT_ON",
+				  "WL_ON",
+				  "PWR_LED_OFF",
+				  "GLOBAL_RESET",
+				  "VDD_SD_IO_SEL",
+				  "CAM_GPIO",
+				  "",
+				  "";
+		status = "okay";
+	};
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>;
+	status = "okay";
+};
+
+/* SDHCI is used to control the SDIO for wireless */
+&sdhci {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_gpio34>;
+	status = "okay";
+	bus-width = <4>;
+	non-removable;
+	mmc-pwrseq = <&wifi_pwrseq>;
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
+/* EMMC2 is used to drive the SD card */
+&emmc2 {
+	status = "okay";
+	broken-cd;
+	vqmmc-supply = <&sd_io_1v8_reg>;
+};
+
+/* uart0 communicates with the BT module */
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32 &gpclk2_gpio43>;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		max-speed = <2000000>;
+		shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+/* uart1 is mapped to the pin header */
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_gpio14>;
+	status = "okay";
+};

arch/arm/boot/dts/bcm2838-rpi.dtsi

@@ -0,0 +1,25 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/ {
+	soc {
+		/delete-node/ mailbox@7e00b840;
+	};
+};
+
+&scb {
+	vchiq: mailbox@7e00b840 {
+		compatible = "brcm,bcm2838-vchiq";
+		reg = <0 0x7e00b840 0x3c>;
+		interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+	};
+};
+
+&dma {
+	/* The VPU firmware uses DMA channel 11 for VCHIQ */
+	brcm,dma-channel-mask = <0x1f5>;
+};
+
+&dma40 {
+	/* The VPU firmware DMA channel 11 for VCHIQ */
+	brcm,dma-channel-mask = <0x7000>;
+};

arch/arm/boot/dts/bcm2838.dtsi

@@ -0,0 +1,746 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "bcm283x.dtsi"
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/soc/bcm2835-pm.h>
+
+/ {
+	compatible = "brcm,bcm2838";
+
+	#address-cells = <2>;
+	#size-cells = <1>;
+
+	interrupt-parent = <&gicv2>;
+
+	soc {
+		ranges = <0x7e000000  0x0 0xfe000000  0x01800000>,
+			 <0x7c000000  0x0 0xfc000000  0x02000000>,
+			 <0x40000000  0x0 0xff800000  0x00800000>;
+		/* Emulate a contiguous 30-bit address range for DMA */
+		dma-ranges = <0xc0000000  0x0 0x00000000  0x3c000000>;
+
+		/delete-node/ interrupt-controller@7e00f300;
+		/delete-node/ v3d@7ec00000;
+
+		local_intc: local_intc@40000000 {
+			compatible = "brcm,bcm2836-l1-intc";
+			reg = <0x40000000 0x100>;
+		};
+
+		gicv2: gic400@40041000 {
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			compatible = "arm,gic-400";
+			reg =	<0x40041000 0x1000>,
+				<0x40042000 0x2000>,
+				<0x40044000 0x2000>,
+				<0x40046000 0x2000>;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) |
+						 IRQ_TYPE_LEVEL_HIGH)>;
+		};
+
+		thermal: thermal@7d5d2200 {
+			compatible = "brcm,avs-tmon-bcm2838";
+			reg = <0x7d5d2200 0x2c>;
+			interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "tmon";
+			clocks = <&clocks BCM2835_CLOCK_TSENS>;
+			#thermal-sensor-cells = <0>;
+			status = "okay";
+		};
+
+		pm: watchdog@7e100000 {
+			reg = <0x7e100000 0x114>,
+			      <0x7e00a000 0x24>,
+			      <0x7ec11000 0x20>;
+		};
+
+		rng@7e104000 {
+			interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		uart2: serial@7e201400 {
+			compatible = "brcm,bcm2835-pl011", "arm,pl011", "arm,primecell";
+			reg = <0x7e201400 0x200>;
+			interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clocks BCM2835_CLOCK_UART>,
+				 <&clocks BCM2835_CLOCK_VPU>;
+			clock-names = "uartclk", "apb_pclk";
+			arm,primecell-periphid = <0x00241011>;
+			status = "disabled";
+		};
+
+		uart3: serial@7e201600 {
+			compatible = "brcm,bcm2835-pl011", "arm,pl011", "arm,primecell";
+			reg = <0x7e201600 0x200>;
+			interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clocks BCM2835_CLOCK_UART>,
+				 <&clocks BCM2835_CLOCK_VPU>;
+			clock-names = "uartclk", "apb_pclk";
+			arm,primecell-periphid = <0x00241011>;
+			status = "disabled";
+		};
+
+		uart4: serial@7e201800 {
+			compatible = "brcm,bcm2835-pl011", "arm,pl011", "arm,primecell";
+			reg = <0x7e201800 0x200>;
+			interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clocks BCM2835_CLOCK_UART>,
+				 <&clocks BCM2835_CLOCK_VPU>;
+			clock-names = "uartclk", "apb_pclk";
+			arm,primecell-periphid = <0x00241011>;
+			status = "disabled";
+		};
+
+		uart5: serial@7e201a00 {
+			compatible = "brcm,bcm2835-pl011", "arm,pl011", "arm,primecell";
+			reg = <0x7e201a00 0x200>;
+			interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clocks BCM2835_CLOCK_UART>,
+				 <&clocks BCM2835_CLOCK_VPU>;
+			clock-names = "uartclk", "apb_pclk";
+			arm,primecell-periphid = <0x00241011>;
+			status = "disabled";
+		};
+
+		spi@7e204000 {
+			reg = <0x7e204000 0x0200>;
+			interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		spi3: spi@7e204600 {
+			compatible = "brcm,bcm2835-spi";
+			reg = <0x7e204600 0x0200>;
+			interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clocks BCM2835_CLOCK_VPU>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		spi4: spi@7e204800 {
+			compatible = "brcm,bcm2835-spi";
+			reg = <0x7e204800 0x0200>;
+			interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clocks BCM2835_CLOCK_VPU>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		spi5: spi@7e204a00 {
+			compatible = "brcm,bcm2835-spi";
+			reg = <0x7e204a00 0x0200>;
+			interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clocks BCM2835_CLOCK_VPU>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		spi6: spi@7e204c00 {
+			compatible = "brcm,bcm2835-spi";
+			reg = <0x7e204c00 0x0200>;
+			interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clocks BCM2835_CLOCK_VPU>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c3: i2c@7e205600 {
+			compatible = "brcm,bcm2835-i2c";
+			reg = <0x7e205600 0x200>;
+			interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clocks BCM2835_CLOCK_VPU>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c4: i2c@7e205800 {
+			compatible = "brcm,bcm2835-i2c";
+			reg = <0x7e205800 0x200>;
+			interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clocks BCM2835_CLOCK_VPU>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c5: i2c@7e205a00 {
+			compatible = "brcm,bcm2835-i2c";
+			reg = <0x7e205a00 0x200>;
+			interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clocks BCM2835_CLOCK_VPU>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c6: i2c@7e205c00 {
+			compatible = "brcm,bcm2835-i2c";
+			reg = <0x7e205c00 0x200>;
+			interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clocks BCM2835_CLOCK_VPU>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		pixelvalve@7e206000 {
+			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		pixelvalve@7e207000 {
+			interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		pwm1: pwm@7e20c800 {
+			compatible = "brcm,bcm2835-pwm";
+			reg = <0x7e20c800 0x28>;
+			clocks = <&clocks BCM2835_CLOCK_PWM>;
+			assigned-clocks = <&clocks BCM2835_CLOCK_PWM>;
+			assigned-clock-rates = <10000000>;
+			#pwm-cells = <2>;
+			status = "disabled";
+		};
+
+		emmc2: emmc2@7e340000 {
+			compatible = "brcm,bcm2711-emmc2";
+			status = "okay";
+			interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clocks BCM2711_CLOCK_EMMC2>;
+			reg = <0x7e340000 0x100>;
+		};
+
+		hvs@7e400000 {
+			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		pixelvalve@7e807000 {
+			interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
+		};
+	};
+
+	arm-pmu {
+		compatible = "arm,cortex-a72-pmu";
+		interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) |
+					  IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) |
+					  IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) |
+					  IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) |
+					  IRQ_TYPE_LEVEL_LOW)>;
+		arm,cpu-registers-not-fw-configured;
+		always-on;
+	};
+
+	cpus: cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		enable-method = "brcm,bcm2836-smp"; // for ARM 32-bit
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a72";
+			reg = <0>;
+			enable-method = "spin-table";
+			cpu-release-addr = <0x0 0x000000d8>;
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a72";
+			reg = <1>;
+			enable-method = "spin-table";
+			cpu-release-addr = <0x0 0x000000e0>;
+		};
+
+		cpu2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a72";
+			reg = <2>;
+			enable-method = "spin-table";
+			cpu-release-addr = <0x0 0x000000e8>;
+		};
+
+		cpu3: cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a72";
+			reg = <3>;
+			enable-method = "spin-table";
+			cpu-release-addr = <0x0 0x000000f0>;
+		};
+	};
+
+	v3dbus {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <2>;
+		ranges = <0x7c500000  0x0 0xfc500000  0x0 0x03300000>,
+			 <0x40000000  0x0 0xff800000  0x0 0x00800000>;
+		dma-ranges = <0x00000000  0x0 0x00000000  0x4 0x00000000>;
+
+		v3d: v3d@7ec04000 {
+			compatible = "brcm,2711-v3d";
+			reg =
+			    <0x7ec00000 0x0 0x4000>,
+			    <0x7ec04000 0x0 0x4000>;
+			reg-names = "hub", "core0";
+
+			power-domains = <&pm BCM2835_POWER_DOMAIN_GRAFX_V3D>;
+			resets = <&pm BCM2835_RESET_V3D>;
+			clocks = <&clocks BCM2835_CLOCK_V3D>;
+			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+			status = "okay";
+		};
+	};
+
+	scb: scb {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <1>;
+
+		ranges = <0x0 0x7c000000  0x0 0xfc000000  0x03800000>,
+			 <0x0 0x40000000  0x0 0xff800000  0x00800000>,
+			 <0x6 0x00000000  0x6 0x00000000  0x40000000>,
+			 <0x0 0x00000000  0x0 0x00000000  0xfc000000>;
+		dma-ranges = <0x0 0x00000000  0x0 0x00000000  0xfc000000>;
+
+		pcie_0: pcie@7d500000 {
+			reg = <0x0 0x7d500000 0x9310>,
+			      <0x0 0x7e00f300 0x20>;
+			msi-controller;
+			msi-parent = <&pcie_0>;
+			#address-cells = <3>;
+			#interrupt-cells = <1>;
+			#size-cells = <2>;
+			bus-range = <0x0 0x01>;
+			compatible = "brcm,bcm7211-pcie", "brcm,bcm7445-pcie",
+				     "brcm,pci-plat-dev";
+			max-link-speed = <2>;
+			tot-num-pcie = <1>;
+			linux,pci-domain = <0>;
+			interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "pcie", "msi";
+			interrupt-map-mask = <0x0 0x0 0x0 0x7>;
+			interrupt-map = <0 0 0 1 &gicv2 GIC_SPI 143
+						IRQ_TYPE_LEVEL_HIGH
+					 0 0 0 2 &gicv2 GIC_SPI 144
+						IRQ_TYPE_LEVEL_HIGH
+					 0 0 0 3 &gicv2 GIC_SPI 145
+						IRQ_TYPE_LEVEL_HIGH
+					 0 0 0 4 &gicv2 GIC_SPI 146
+						IRQ_TYPE_LEVEL_HIGH>;
+
+			/* Map outbound accesses from scb:0x6_00000000-03ffffff
+			 * to pci:0x0_f8000000-fbffffff
+			 */
+			ranges = <0x02000000 0x0 0xf8000000  0x6 0x00000000
+				  0x0 0x04000000>;
+			/* Map inbound accesses from pci:0x0_00000000..ffffffff
+			 * to scb:0x0_00000000-ffffffff
+			 */
+			dma-ranges = <0x02000000 0x0 0x00000000  0x0 0x00000000
+				      0x1 0x00000000>;
+			status = "okay";
+		};
+
+		genet: genet@7d580000 {
+			compatible = "brcm,genet-v5";
+			reg = <0x0 0x7d580000 0x10000>;
+			status = "okay";
+			#address-cells = <0x1>;
+			#size-cells = <0x1>;
+			interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>;
+			phy-handle = <&phy1>;
+			phy-mode = "rgmii";
+			mdio@e14 {
+				#address-cells = <0x0>;
+				#size-cells = <0x1>;
+				compatible = "brcm,genet-mdio-v5";
+				reg = <0xe14 0x8>;
+				reg-names = "mdio";
+				phy1: genet-phy@0 {
+					compatible =
+						"ethernet-phy-ieee802.3-c22";
+					/* No interrupts - use PHY_POLL */
+					max-speed = <1000>;
+					reg = <0x1>;
+				};
+			};
+		};
+
+		dma40: dma@7e007b00 {
+			compatible = "brcm,bcm2838-dma";
+			reg = <0x0 0x7e007b00 0x400>;
+			interrupts =
+				<GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>, /* dma4 11 */
+				<GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>, /* dma4 12 */
+				<GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>, /* dma4 13 */
+				<GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>; /* dma4 14 */
+			interrupt-names = "dma11",
+				"dma12",
+				"dma13",
+				"dma14";
+			#dma-cells = <1>;
+			brcm,dma-channel-mask = <0x7800>;
+		};
+		/* DMA4 - 40 bit DMA engines */
+
+		xhci: xhci@7e9c0000 {
+			compatible = "generic-xhci";
+			status = "disabled";
+			reg = <0x0 0x7e9c0000 0x100000>;
+			interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		hevc-decoder@7eb00000 {
+			compatible = "raspberrypi,rpivid-hevc-decoder";
+			reg = <0x0 0x7eb00000 0x10000>;
+			status = "okay";
+		};
+
+		rpivid-local-intc@7eb10000 {
+			compatible = "raspberrypi,rpivid-local-intc";
+			reg = <0x0 0x7eb10000 0x1000>;
+			status = "okay";
+			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		h264-decoder@7eb20000 {
+			compatible = "raspberrypi,rpivid-h264-decoder";
+			reg = <0x0 0x7eb20000 0x10000>;
+			status = "okay";
+		};
+
+		vp9-decoder@7eb30000 {
+			compatible = "raspberrypi,rpivid-vp9-decoder";
+			reg = <0x0 0x7eb30000 0x10000>;
+			status = "okay";
+		};
+	};
+};
+
+&clk_osc {
+	clock-frequency = <54000000>;
+};
+
+&clocks {
+	compatible = "brcm,bcm2711-cprman";
+};
+
+&cpu_thermal {
+	coefficients = <(-487)  410040>;
+};
+
+&dsi0 {
+	interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&dsi1 {
+	interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&gpio {
+	compatible = "brcm,bcm2711-gpio", "brcm,bcm2835-gpio";
+
+	gpclk0_gpio49: gpclk0_gpio49 {
+		brcm,pins = <49>;
+		brcm,function = <BCM2835_FSEL_ALT1>;
+		brcm,pull = <BCM2835_PUD_OFF>;
+	};
+	gpclk1_gpio50: gpclk1_gpio50 {
+		brcm,pins = <50>;
+		brcm,function = <BCM2835_FSEL_ALT1>;
+		brcm,pull = <BCM2835_PUD_OFF>;
+	};
+	gpclk2_gpio51: gpclk2_gpio51 {
+		brcm,pins = <51>;
+		brcm,function = <BCM2835_FSEL_ALT1>;
+		brcm,pull = <BCM2835_PUD_OFF>;
+	};
+
+	i2c0_gpio46: i2c0_gpio46 {
+		brcm,pins = <46 47>;
+		brcm,function = <BCM2835_FSEL_ALT0>;
+	};
+	i2c1_gpio46: i2c1_gpio46 {
+		brcm,pins = <46 47>;
+		brcm,function = <BCM2835_FSEL_ALT1>;
+	};
+	i2c3_gpio2: i2c3_gpio2 {
+		brcm,pins = <2 3>;
+		brcm,function = <BCM2835_FSEL_ALT5>;
+	};
+	i2c3_gpio4: i2c3_gpio4 {
+		brcm,pins = <4 5>;
+		brcm,function = <BCM2835_FSEL_ALT5>;
+	};
+	i2c4_gpio6: i2c4_gpio6 {
+		brcm,pins = <6 7>;
+		brcm,function = <BCM2835_FSEL_ALT5>;
+	};
+	i2c4_gpio8: i2c4_gpio8 {
+		brcm,pins = <8 9>;
+		brcm,function = <BCM2835_FSEL_ALT5>;
+	};
+	i2c5_gpio10: i2c5_gpio10 {
+		brcm,pins = <10 11>;
+		brcm,function = <BCM2835_FSEL_ALT5>;
+	};
+	i2c5_gpio12: i2c5_gpio12 {
+		brcm,pins = <12 13>;
+		brcm,function = <BCM2835_FSEL_ALT5>;
+	};
+	i2c6_gpio0: i2c6_gpio0 {
+		brcm,pins = <0 1>;
+		brcm,function = <BCM2835_FSEL_ALT5>;
+	};
+	i2c6_gpio22: i2c6_gpio22 {
+		brcm,pins = <22 23>;
+		brcm,function = <BCM2835_FSEL_ALT5>;
+	};
+	i2c_slave_gpio8: i2c_slave_gpio8 {
+		brcm,pins = <8 9 10 11>;
+		brcm,function = <BCM2835_FSEL_ALT3>;
+	};
+
+	jtag_gpio48: jtag_gpio48 {
+		brcm,pins = <48 49 50 51 52 53>;
+		brcm,function = <BCM2835_FSEL_ALT4>;
+	};
+
+	mii_gpio28: mii_gpio28 {
+		brcm,pins = <28 29 30 31>;
+		brcm,function = <BCM2835_FSEL_ALT4>;
+	};
+	mii_gpio36: mii_gpio36 {
+		brcm,pins = <36 37 38 39>;
+		brcm,function = <BCM2835_FSEL_ALT5>;
+	};
+
+	pcm_gpio50: pcm_gpio50 {
+		brcm,pins = <50 51 52 53>;
+		brcm,function = <BCM2835_FSEL_ALT2>;
+	};
+
+	pwm0_gpio52: pwm0_gpio52 {
+		brcm,pins = <52>;
+		brcm,function = <BCM2835_FSEL_ALT1>;
+		brcm,pull = <BCM2835_PUD_OFF>;
+	};
+	pwm1_gpio53: pwm1_gpio53 {
+		brcm,pins = <53>;
+		brcm,function = <BCM2835_FSEL_ALT1>;
+		brcm,pull = <BCM2835_PUD_OFF>;
+	};
+
+	/* The following group consists of:
+         *  RGMII_START_STOP
+         *  RGMII_RX_OK
+         */
+	rgmii_gpio35: rgmii_gpio35 {
+		brcm,pins = <35 36>;
+		brcm,function = <BCM2835_FSEL_ALT4>;
+	};
+	rgmii_irq_gpio34: rgmii_irq_gpio34 {
+		brcm,pins = <34>;
+		brcm,function = <BCM2835_FSEL_ALT5>;
+	};
+	rgmii_irq_gpio39: rgmii_irq_gpio39 {
+		brcm,pins = <39>;
+		brcm,function = <BCM2835_FSEL_ALT4>;
+	};
+	rgmii_mdio_gpio28: rgmii_mdio_gpio28 {
+		brcm,pins = <28 29>;
+		brcm,function = <BCM2835_FSEL_ALT5>;
+	};
+	rgmii_mdio_gpio37: rgmii_mdio_gpio37 {
+		brcm,pins = <37 38>;
+		brcm,function = <BCM2835_FSEL_ALT4>;
+	};
+
+	spi0_gpio46: spi0_gpio46 {
+		brcm,pins = <46 47 48 49>;
+		brcm,function = <BCM2835_FSEL_ALT2>;
+	};
+	spi2_gpio46: spi2_gpio46 {
+		brcm,pins = <46 47 48 49 50>;
+		brcm,function = <BCM2835_FSEL_ALT5>;
+	};
+	spi3_gpio0: spi3_gpio0 {
+		brcm,pins = <0 1 2 3>;
+		brcm,function = <BCM2835_FSEL_ALT3>;
+	};
+	spi4_gpio4: spi4_gpio4 {
+		brcm,pins = <4 5 6 7>;
+		brcm,function = <BCM2835_FSEL_ALT3>;
+	};
+	spi5_gpio12: spi5_gpio12 {
+		brcm,pins = <12 13 14 15>;
+		brcm,function = <BCM2835_FSEL_ALT3>;
+	};
+	spi6_gpio18: spi6_gpio18 {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <BCM2835_FSEL_ALT3>;
+	};
+
+	uart2_gpio0: uart2_gpio0 {
+		brcm,pins = <0 1>;
+		brcm,function = <BCM2835_FSEL_ALT4>;
+		brcm,pull = <BCM2835_PUD_OFF BCM2835_PUD_UP>;
+	};
+	uart2_ctsrts_gpio2: uart2_ctsrts_gpio2 {
+		brcm,pins = <2 3>;
+		brcm,function = <BCM2835_FSEL_ALT4>;
+		brcm,pull = <BCM2835_PUD_UP BCM2835_PUD_OFF>;
+	};
+	uart3_gpio4: uart3_gpio4 {
+		brcm,pins = <4 5>;
+		brcm,function = <BCM2835_FSEL_ALT4>;
+		brcm,pull = <BCM2835_PUD_OFF BCM2835_PUD_UP>;
+	};
+	uart3_ctsrts_gpio6: uart3_ctsrts_gpio6 {
+		brcm,pins = <6 7>;
+		brcm,function = <BCM2835_FSEL_ALT4>;
+		brcm,pull = <BCM2835_PUD_UP BCM2835_PUD_OFF>;
+	};
+	uart4_gpio8: uart4_gpio8 {
+		brcm,pins = <8 9>;
+		brcm,function = <BCM2835_FSEL_ALT4>;
+		brcm,pull = <BCM2835_PUD_OFF BCM2835_PUD_UP>;
+	};
+	uart4_ctsrts_gpio10: uart4_ctsrts_gpio10 {
+		brcm,pins = <10 11>;
+		brcm,function = <BCM2835_FSEL_ALT4>;
+		brcm,pull = <BCM2835_PUD_UP BCM2835_PUD_OFF>;
+	};
+	uart5_gpio12: uart5_gpio12 {
+		brcm,pins = <12 13>;
+		brcm,function = <BCM2835_FSEL_ALT4>;
+		brcm,pull = <BCM2835_PUD_OFF BCM2835_PUD_UP>;
+	};
+	uart5_ctsrts_gpio14: uart5_ctsrts_gpio14 {
+		brcm,pins = <14 15>;
+		brcm,function = <BCM2835_FSEL_ALT4>;
+		brcm,pull = <BCM2835_PUD_UP BCM2835_PUD_OFF>;
+	};
+};
+
+&vec {
+	interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&usb {
+	interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+	status = "disabled";
+};
+
+&hdmi {
+	interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&uart1 {
+	interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&spi1 {
+	interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&spi2 {
+	interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&csi0 {
+	interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&csi1 {
+	interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&sdhci {
+	interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&i2c0 {
+	interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&i2c1 {
+	interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&i2c2 {
+	interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&gpio {
+	interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&mailbox {
+	interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&rng {
+	compatible = "brcm,bcm2838-rng200";
+};
+
+&sdhost {
+	interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&uart0 {
+	interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&dma {
+	reg = <0x7e007000 0xb00>;
+	interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>,
+		<GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>,
+		<GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>,
+		<GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>,
+		<GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>,
+		<GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>,
+		<GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>,
+		<GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>, /* dmalite  7 */
+		<GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>, /* dmalite  8 */
+		<GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>, /* dmalite  9 */
+		<GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>; /* dmalite 10 */
+	interrupt-names = "dma0",
+			  "dma1",
+			  "dma2",
+			  "dma3",
+			  "dma4",
+			  "dma5",
+			  "dma6",
+			  "dma7",
+			  "dma8",
+			  "dma9",
+			  "dma10";
+	brcm,dma-channel-mask = <0x07f5>;
+};
+
+&txp {
+	interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+};

arch/arm/boot/dts/bcm283x-rpi-csi0-2lane.dtsi

@@ -0,0 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
+&csi0 {
+	port {
+		endpoint {
+			data-lanes = <1 2>;
+		};
+	};
+};

arch/arm/boot/dts/bcm283x-rpi-csi1-2lane.dtsi

@@ -0,0 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
+&csi1 {
+	port {
+		endpoint {
+			data-lanes = <1 2>;
+		};
+	};
+};

arch/arm/boot/dts/bcm283x-rpi-csi1-4lane.dtsi

@@ -0,0 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
+&csi1 {
+	port {
+		endpoint {
+			data-lanes = <1 2 3 4>;
+		};
+	};
+};

arch/arm/boot/dts/bcm283x-rpi-lan7515.dtsi

@@ -29,6 +29,9 @@
 					#size-cells = <0x0>;
 					eth_phy: ethernet-phy@1 {
 						reg = <1>;
+						microchip,eee-enabled;
+						microchip,tx-lpi-timer = <600>; /* non-aggressive*/
+						microchip,downshift-after = <2>;
 						microchip,led-modes = <
 							LAN78XX_LINK_1000_ACTIVITY
 							LAN78XX_LINK_10_100_ACTIVITY
@@ -39,3 +42,15 @@
 		};
 	};
 };
+
+
+/ {
+	__overrides__ {
+		eee = <&eth_phy>,"microchip,eee-enabled?";
+		tx_lpi_timer = <&eth_phy>,"microchip,tx-lpi-timer:0";
+		eth_led0 = <&eth_phy>,"microchip,led-modes:0";
+		eth_led1 = <&eth_phy>,"microchip,led-modes:4";
+		eth_downshift_after = <&eth_phy>,"microchip,downshift-after:0";
+		eth_max_speed = <&eth_phy>,"max-speed:0";
+	};
+};

arch/arm/boot/dts/bcm283x.dtsi

@@ -56,18 +56,7 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 
-		timer@7e003000 {
+		txp: txp@7e004000 {
-			compatible = "brcm,bcm2835-system-timer";
-			reg = <0x7e003000 0x1000>;
-			interrupts = <1 0>, <1 1>, <1 2>, <1 3>;
-			/* This could be a reference to BCM2835_CLOCK_TIMER,
-			 * but we don't have the driver using the common clock
-			 * support yet.
-			 */
-			clock-frequency = <1000000>;
-		};
-
-		txp@7e004000 {
 			compatible = "brcm,bcm2835-txp";
 			reg = <0x7e004000 0x20>;
 			interrupts = <1 11>;
@@ -114,13 +103,6 @@
 			brcm,dma-channel-mask = <0x7f35>;
 		};
 
-		intc: interrupt-controller@7e00b200 {
-			compatible = "brcm,bcm2835-armctrl-ic";
-			reg = <0x7e00b200 0x200>;
-			interrupt-controller;
-			#interrupt-cells = <2>;
-		};
-
 		pm: watchdog@7e100000 {
 			compatible = "brcm,bcm2835-pm", "brcm,bcm2835-pm-wdt";
 			#power-domain-cells = <1>;
@@ -149,7 +131,7 @@
 				<&dsi1 0>, <&dsi1 1>, <&dsi1 2>;
 		};
 
-		rng@7e104000 {
+		rng: rng@7e104000 {
 			compatible = "brcm,bcm2835-rng";
 			reg = <0x7e104000 0x10>;
 			interrupts = <2 29>;
@@ -184,8 +166,7 @@
 			interrupt-controller;
 			#interrupt-cells = <2>;
 
-			/* Defines pin muxing groups according to
+			/* Defines common pin muxing groups
-			 * BCM2835-ARM-Peripherals.pdf page 102.
 			 *
 			 * While each pin can have its mux selected
 			 * for various functions individually, some
@@ -263,15 +244,7 @@
 				brcm,pins = <44 45>;
 				brcm,function = <BCM2835_FSEL_ALT2>;
 			};
-			i2c_slave_gpio18: i2c_slave_gpio18 {
-				brcm,pins = <18 19 20 21>;
-				brcm,function = <BCM2835_FSEL_ALT3>;
-			};
 
-			jtag_gpio4: jtag_gpio4 {
-				brcm,pins = <4 5 6 12 13>;
-				brcm,function = <BCM2835_FSEL_ALT5>;
-			};
 			jtag_gpio22: jtag_gpio22 {
 				brcm,pins = <22 23 24 25 26 27>;
 				brcm,function = <BCM2835_FSEL_ALT4>;
@@ -397,7 +370,7 @@
 
 		uart0: serial@7e201000 {
 			compatible = "brcm,bcm2835-pl011", "arm,pl011", "arm,primecell";
-			reg = <0x7e201000 0x1000>;
+			reg = <0x7e201000 0x200>;
 			interrupts = <2 25>;
 			clocks = <&clocks BCM2835_CLOCK_UART>,
 				 <&clocks BCM2835_CLOCK_VPU>;
@@ -410,7 +383,7 @@
 			reg = <0x7e202000 0x100>;
 			interrupts = <2 24>;
 			clocks = <&clocks BCM2835_CLOCK_VPU>;
-			dmas = <&dma 13>;
+			dmas = <&dma (13|(1<<29))>;
 			dma-names = "rx-tx";
 			status = "disabled";
 		};
@@ -428,7 +401,7 @@
 
 		spi: spi@7e204000 {
 			compatible = "brcm,bcm2835-spi";
-			reg = <0x7e204000 0x1000>;
+			reg = <0x7e204000 0x200>;
 			interrupts = <2 22>;
 			clocks = <&clocks BCM2835_CLOCK_VPU>;
 			dmas = <&dma 6>, <&dma 7>;
@@ -440,7 +413,7 @@
 
 		i2c0: i2c@7e205000 {
 			compatible = "brcm,bcm2835-i2c";
-			reg = <0x7e205000 0x1000>;
+			reg = <0x7e205000 0x200>;
 			interrupts = <2 21>;
 			clocks = <&clocks BCM2835_CLOCK_VPU>;
 			#address-cells = <1>;
@@ -490,14 +463,6 @@
 
 		};
 
-		thermal: thermal@7e212000 {
-			compatible = "brcm,bcm2835-thermal";
-			reg = <0x7e212000 0x8>;
-			clocks = <&clocks BCM2835_CLOCK_TSENS>;
-			#thermal-sensor-cells = <0>;
-			status = "disabled";
-		};
-
 		aux: aux@7e215000 {
 			compatible = "brcm,bcm2835-aux";
 			#clock-cells = <1>;
@@ -577,6 +542,32 @@
 			status = "disabled";
 		};
 
+		csi0: csi@7e800000 {
+			compatible = "brcm,bcm2835-unicam";
+			reg = <0x7e800000 0x800>,
+			      <0x7e802000 0x4>;
+			interrupts = <2 6>;
+			clocks = <&clocks BCM2835_CLOCK_CAM0>;
+			clock-names = "lp";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#clock-cells = <1>;
+			status = "disabled";
+		};
+
+		csi1: csi@7e801000 {
+			compatible = "brcm,bcm2835-unicam";
+			reg = <0x7e801000 0x800>,
+			      <0x7e802004 0x4>;
+			interrupts = <2 7>;
+			clocks = <&clocks BCM2835_CLOCK_CAM1>;
+			clock-names = "lp";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#clock-cells = <1>;
+			status = "disabled";
+		};
+
 		i2c1: i2c@7e804000 {
 			compatible = "brcm,bcm2835-i2c";
 			reg = <0x7e804000 0x1000>;
@@ -637,13 +628,6 @@
 			phy-names = "usb2-phy";
 		};
 
-		v3d: v3d@7ec00000 {
-			compatible = "brcm,bcm2835-v3d";
-			reg = <0x7ec00000 0x1000>;
-			interrupts = <1 10>;
-			power-domains = <&pm BCM2835_POWER_DOMAIN_GRAFX_V3D>;
-		};
-
 		vc4: gpu {
 			compatible = "brcm,bcm2835-vc4";
 		};

arch/arm/boot/dts/dra7-l4.dtsi

@@ -2762,7 +2762,7 @@
 				interrupt-names = "tx", "rx";
 				dmas = <&edma_xbar 129 1>, <&edma_xbar 128 1>;
 				dma-names = "tx", "rx";
-				clocks = <&ipu_clkctrl DRA7_IPU_MCASP1_CLKCTRL 22>,
+				clocks = <&ipu_clkctrl DRA7_IPU_MCASP1_CLKCTRL 0>,
 					 <&ipu_clkctrl DRA7_IPU_MCASP1_CLKCTRL 24>,
 					 <&ipu_clkctrl DRA7_IPU_MCASP1_CLKCTRL 28>;
 				clock-names = "fck", "ahclkx", "ahclkr";
@@ -2799,8 +2799,8 @@
 				interrupt-names = "tx", "rx";
 				dmas = <&edma_xbar 131 1>, <&edma_xbar 130 1>;
 				dma-names = "tx", "rx";
-				clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP2_CLKCTRL 22>,
+				clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP2_CLKCTRL 0>,
-					 <&l4per2_clkctrl DRA7_L4PER2_MCASP2_CLKCTRL 24>,
+					 <&ipu_clkctrl DRA7_IPU_MCASP1_CLKCTRL 24>,
 					 <&l4per2_clkctrl DRA7_L4PER2_MCASP2_CLKCTRL 28>;
 				clock-names = "fck", "ahclkx", "ahclkr";
 				status = "disabled";
@@ -2818,9 +2818,8 @@
 					<SYSC_IDLE_SMART>;
 			/* Domains (P, C): l4per_pwrdm, l4per2_clkdm */
 			clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP3_CLKCTRL 0>,
-				 <&l4per2_clkctrl DRA7_L4PER2_MCASP3_CLKCTRL 24>,
+				 <&l4per2_clkctrl DRA7_L4PER2_MCASP3_CLKCTRL 24>;
-				 <&l4per2_clkctrl DRA7_L4PER2_MCASP3_CLKCTRL 28>;
+			clock-names = "fck", "ahclkx";
-			clock-names = "fck", "ahclkx", "ahclkr";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0x0 0x68000 0x2000>,
@@ -2836,7 +2835,7 @@
 				interrupt-names = "tx", "rx";
 				dmas = <&edma_xbar 133 1>, <&edma_xbar 132 1>;
 				dma-names = "tx", "rx";
-				clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP3_CLKCTRL 22>,
+				clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP3_CLKCTRL 0>,
 					 <&l4per2_clkctrl DRA7_L4PER2_MCASP3_CLKCTRL 24>;
 				clock-names = "fck", "ahclkx";
 				status = "disabled";
@@ -2854,9 +2853,8 @@
 					<SYSC_IDLE_SMART>;
 			/* Domains (P, C): l4per_pwrdm, l4per2_clkdm */
 			clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP4_CLKCTRL 0>,
-				 <&l4per2_clkctrl DRA7_L4PER2_MCASP4_CLKCTRL 24>,
+				 <&l4per2_clkctrl DRA7_L4PER2_MCASP4_CLKCTRL 24>;
-				 <&l4per2_clkctrl DRA7_L4PER2_MCASP4_CLKCTRL 28>;
+			clock-names = "fck", "ahclkx";
-			clock-names = "fck", "ahclkx", "ahclkr";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0x0 0x6c000 0x2000>,
@@ -2872,7 +2870,7 @@
 				interrupt-names = "tx", "rx";
 				dmas = <&edma_xbar 135 1>, <&edma_xbar 134 1>;
 				dma-names = "tx", "rx";
-				clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP4_CLKCTRL 22>,
+				clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP4_CLKCTRL 0>,
 					 <&l4per2_clkctrl DRA7_L4PER2_MCASP4_CLKCTRL 24>;
 				clock-names = "fck", "ahclkx";
 				status = "disabled";
@@ -2890,9 +2888,8 @@
 					<SYSC_IDLE_SMART>;
 			/* Domains (P, C): l4per_pwrdm, l4per2_clkdm */
 			clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP5_CLKCTRL 0>,
-				 <&l4per2_clkctrl DRA7_L4PER2_MCASP5_CLKCTRL 24>,
+				 <&l4per2_clkctrl DRA7_L4PER2_MCASP5_CLKCTRL 24>;
-				 <&l4per2_clkctrl DRA7_L4PER2_MCASP5_CLKCTRL 28>;
+			clock-names = "fck", "ahclkx";
-			clock-names = "fck", "ahclkx", "ahclkr";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0x0 0x70000 0x2000>,
@@ -2908,7 +2905,7 @@
 				interrupt-names = "tx", "rx";
 				dmas = <&edma_xbar 137 1>, <&edma_xbar 136 1>;
 				dma-names = "tx", "rx";
-				clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP5_CLKCTRL 22>,
+				clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP5_CLKCTRL 0>,
 					 <&l4per2_clkctrl DRA7_L4PER2_MCASP5_CLKCTRL 24>;
 				clock-names = "fck", "ahclkx";
 				status = "disabled";
@@ -2926,9 +2923,8 @@
 					<SYSC_IDLE_SMART>;
 			/* Domains (P, C): l4per_pwrdm, l4per2_clkdm */
 			clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP6_CLKCTRL 0>,
-				 <&l4per2_clkctrl DRA7_L4PER2_MCASP6_CLKCTRL 24>,
+				 <&l4per2_clkctrl DRA7_L4PER2_MCASP6_CLKCTRL 24>;
-				 <&l4per2_clkctrl DRA7_L4PER2_MCASP6_CLKCTRL 28>;
+			clock-names = "fck", "ahclkx";
-			clock-names = "fck", "ahclkx", "ahclkr";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0x0 0x74000 0x2000>,
@@ -2944,7 +2940,7 @@
 				interrupt-names = "tx", "rx";
 				dmas = <&edma_xbar 139 1>, <&edma_xbar 138 1>;
 				dma-names = "tx", "rx";
-				clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP6_CLKCTRL 22>,
+				clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP6_CLKCTRL 0>,
 					 <&l4per2_clkctrl DRA7_L4PER2_MCASP6_CLKCTRL 24>;
 				clock-names = "fck", "ahclkx";
 				status = "disabled";
@@ -2962,9 +2958,8 @@
 					<SYSC_IDLE_SMART>;
 			/* Domains (P, C): l4per_pwrdm, l4per2_clkdm */
 			clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP7_CLKCTRL 0>,
-				 <&l4per2_clkctrl DRA7_L4PER2_MCASP7_CLKCTRL 24>,
+				 <&l4per2_clkctrl DRA7_L4PER2_MCASP7_CLKCTRL 24>;
-				 <&l4per2_clkctrl DRA7_L4PER2_MCASP7_CLKCTRL 28>;
+			clock-names = "fck", "ahclkx";
-			clock-names = "fck", "ahclkx", "ahclkr";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0x0 0x78000 0x2000>,
@@ -2980,7 +2975,7 @@
 				interrupt-names = "tx", "rx";
 				dmas = <&edma_xbar 141 1>, <&edma_xbar 140 1>;
 				dma-names = "tx", "rx";
-				clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP7_CLKCTRL 22>,
+				clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP7_CLKCTRL 0>,
 					 <&l4per2_clkctrl DRA7_L4PER2_MCASP7_CLKCTRL 24>;
 				clock-names = "fck", "ahclkx";
 				status = "disabled";
@@ -2998,9 +2993,8 @@
 					<SYSC_IDLE_SMART>;
 			/* Domains (P, C): l4per_pwrdm, l4per2_clkdm */
 			clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP8_CLKCTRL 0>,
-				 <&l4per2_clkctrl DRA7_L4PER2_MCASP8_CLKCTRL 24>,
+				 <&l4per2_clkctrl DRA7_L4PER2_MCASP8_CLKCTRL 24>;
-				 <&l4per2_clkctrl DRA7_L4PER2_MCASP8_CLKCTRL 28>;
+			clock-names = "fck", "ahclkx";
-			clock-names = "fck", "ahclkx", "ahclkr";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0x0 0x7c000 0x2000>,
@@ -3016,7 +3010,7 @@
 				interrupt-names = "tx", "rx";
 				dmas = <&edma_xbar 143 1>, <&edma_xbar 142 1>;
 				dma-names = "tx", "rx";
-				clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP8_CLKCTRL 22>,
+				clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP8_CLKCTRL 0>,
 					 <&l4per2_clkctrl DRA7_L4PER2_MCASP8_CLKCTRL 24>;
 				clock-names = "fck", "ahclkx";
 				status = "disabled";

arch/arm/boot/dts/exynos5420-peach-pit.dts

@@ -440,6 +440,7 @@
 				regulator-name = "vdd_ldo10";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
 				regulator-state-mem {
 					regulator-off-in-suspend;
 				};

arch/arm/boot/dts/exynos5800-peach-pi.dts

@@ -440,6 +440,7 @@
 				regulator-name = "vdd_ldo10";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
 				regulator-state-mem {
 					regulator-off-in-suspend;
 				};

arch/arm/boot/dts/gemini-dlink-dir-685.dts

@@ -72,7 +72,6 @@
 			reg = <0>;
 			/* 50 ns min period = 20 MHz */
 			spi-max-frequency = <20000000>;
-			spi-cpol; /* Clock active low */
 			vcc-supply = <&vdisp>;
 			iovcc-supply = <&vdisp>;
 			vci-supply = <&vdisp>;

arch/arm/boot/dts/imx6-logicpd-baseboard.dtsi

@@ -328,6 +328,10 @@
 	pinctrl-0 = <&pinctrl_pwm3>;
 };
 
+&snvs_pwrkey {
+	status = "okay";
+};
+
 &ssi2 {
 	status = "okay";
 };

arch/arm/boot/dts/imx6-logicpd-som.dtsi

@@ -207,6 +207,10 @@
 	vin-supply = <&sw1c_reg>;
 };
 
+&snvs_poweroff {
+	status = "okay";
+};
+
 &iomuxc {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_hog>;

arch/arm/boot/dts/imx6qdl-sabreauto.dtsi

@@ -230,6 +230,8 @@
 			accelerometer@1c {
 				compatible = "fsl,mma8451";
 				reg = <0x1c>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_mma8451_int>;
 				interrupt-parent = <&gpio6>;
 				interrupts = <31 IRQ_TYPE_LEVEL_LOW>;
 			};
@@ -628,6 +630,12 @@
 			>;
 		};
 
+		pinctrl_mma8451_int: mma8451intgrp {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_BCLK__GPIO6_IO31		0xb0b1
+			>;
+		};
+
 		pinctrl_pwm3: pwm1grp {
 			fsl,pins = <
 				MX6QDL_PAD_SD4_DAT1__PWM3_OUT		0x1b0b1

arch/arm/boot/dts/imx7-colibri.dtsi

@@ -323,6 +323,7 @@
 	vmmc-supply = <&reg_module_3v3>;
 	vqmmc-supply = <&reg_DCDC3>;
 	non-removable;
+	sdhci-caps-mask = <0x80000000 0x0>;
 };
 
 &iomuxc {

arch/arm/boot/dts/imx7d-cl-som-imx7.dts

@@ -44,7 +44,7 @@
 			  <&clks IMX7D_ENET1_TIME_ROOT_CLK>;
 	assigned-clock-parents = <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>;
 	assigned-clock-rates = <0>, <100000000>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-handle = <&ethphy0>;
 	fsl,magic-packet;
 	status = "okay";
@@ -70,7 +70,7 @@
 			  <&clks IMX7D_ENET2_TIME_ROOT_CLK>;
 	assigned-clock-parents = <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>;
 	assigned-clock-rates = <0>, <100000000>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-handle = <&ethphy1>;
 	fsl,magic-packet;
 	status = "okay";